γ-Oryzanol and tocopherol contents in residues of rice bran oil refining.

Science.gov (United States)

Pestana-Bauer, Vanessa Ribeiro; Zambiazi, Rui C; Mendonça, Carla R B; Beneito-Cambra, Miriam; Ramis-Ramos, Guillermo

2012-10-01

Rice bran oil (RBO) contains significant amounts of the natural antioxidants γ-oryzanol and tocopherols, which are lost to a large degree during oil refining. This results in a number of industrial residues with high contents of these phytochemicals. With the aim of supporting the development of profitable industrial procedures for γ-oryzanol and tocopherol recovery, the contents of these phytochemicals in all the residues produced during RBO refining were evaluated. The samples included residues from the degumming, soap precipitation, bleaching earth filtering, dewaxing and deodorisation distillation steps. The highest phytochemical concentrations were found in the precipitated soap for γ-oryzanol (14.2 mg g(-1), representing 95.3% of total γ-oryzanol in crude RBO), and in the deodorisation distillate for tocopherols (576 mg 100 g(-1), representing 6.7% of total tocopherols in crude RBO). Therefore, among the residues of RBO processing, the deodorisation distillate was the best source of tocopherols. As the soap is further processed for the recovery of fatty acids, samples taken from every step of this secondary process, including hydrosoluble fraction, hydrolysed soap, distillation residue and purified fatty acid fraction, were also analyzed. The distillation residue left after fatty acid recovery from soap was found to be the best source of γ-oryzanol (43.1 mg g(-1), representing 11.5% of total γ-oryzanol in crude RBO). Copyright © 2012 Elsevier Ltd. All rights reserved.

Acephate and buprofezin residues in olives and olive oil.

Science.gov (United States)

Cabras, P; Angioni, A; Garau, V L; Pirisi, F M; Cabitza, F; Pala, M

2000-10-01

Field trials were carried out to study the persistence of acephate and buprofezin on olives. Two cultivars, pizz'e carroga and pendolino, with very large and small fruits respectively were used. After treatment, no difference was found between the two pesticide deposits on the olives. The disappearance rates, calculated as pseudo first order kinetics, were similar for both pesticides (on average 12 days). Methamidophos, the acephate metabolite, was always present on all olives, and in some pendolino samples it showed higher residues than the maximum residue limit (MRL). During washing, the first step of olive processing, the residue level of both pesticides on the olives did not decrease. After processing of the olives into oil, no residues of acephate or methamidophos were found in the olive oil, while the residues of buprofezin were on average four times higher than on olives.

Efficiency of the refining processes in removing 14C-dichlorvos residues in soybean oil

International Nuclear Information System (INIS)

Soliman, S.M.

2006-01-01

Crude soybean oil extracted from grains treated with 14 C-dichlorvos at a dose 24 mg insecticide / kg seeds and stored for 30 weeks was subjected to different refining processes such as alkali treatment, bleaching, winterization and deodorization. The effect of the refining processes on the nature and magnitude of the originally present residues was investigated. The insecticide residues in crude oil and cake amounted to 9.5% and 55% , respectively, of original residues inside the seeds. Extraction of the seeds with hexane gave crude oil with 9.5 % of original residues in seeds. The l4 C-activity in the crude stored Soya beans oil could be reduced by about 82% of radioactivity originally present in crude oil eliminated by simulated commercial processes locally used for oil refining. A high percentage of the residues (50-55%) were eliminated during alkali treatment and bleaching. Refining of soybeans oil fortified with '1 4 C-dichlorovos. The final refined oil had only 13% of the radioactivity originally present, mainly in the form of dichlorvos, dimethyl and monomethyl phosphate in addition to desmethyl dichlorvos in oil with aged residues

Biodiesel production from residual oils recovered from spent bleaching earth

International Nuclear Information System (INIS)

Huang, Yi-Pin; Chang, James I.

2010-01-01

This work was to study technical and economic feasibilities of converting residual oils recovered from spent bleaching earth generated at soybean oil refineries into useable biodiesel. Experimental results showed that fatty acids in the SBE residual oil were hexadecenoic acid (58.19%), stearic acid (21.49%) and oleic acid (20.32%), which were similar to those of vegetable oils. The methyl ester conversion via a transesterification process gave a yield between 85 and 90%. The biodiesel qualities were in reasonable agreement with both EN 14214 and ASTM D6751 standards. A preliminary financial analysis showed that the production cost of biodiesel from SBE oils was significantly lower than the pre-tax price of fossil diesel or those made of vegetable oils or waste cooking oils. The effects of the crude oil price and the investment on the production cost and the investment return period were also conducted. The result showed that the investment would return faster at higher crude oil price. (author)

The Effect of Processing on 14C- Chlofenvinphos Residues in Maize Oil and Bioavailability of its Cake Residues on Rats

International Nuclear Information System (INIS)

Mahdy, F.; El-Maghraby, S.

2008-01-01

Maize seed obtained from 14 C-chlofenvinphos treated plants contained 0.12 % of the applied dose. The insecticide residues in crude oil, methanol and coke amounted to 10 %, 6 % and 69 %, respectively of original residues inside the seeds.The 14 C activity in the crude oil could be a gradual reduced by the refining processes. The alkali treatment and bleaching steps are more effective steps in the refining processes remove about (63 %). The refined oil contained only about 17 % of the 14 C-residues originally present. The major residues in processed oil contain parent compound, in addition to five metabolites of the insecticide. When rats fed the extracted seeds (cake), the bound residues were found to be considerably bioavailable. After feeding rats for 5 days with the cake, a substantial amount of 14 C-residues was eliminated in the urine (59.5 %), while about 20 % was excreted in the feces. About 15 % of the radioactivity was distribution among various organs

Research within the coordinated programme on isotopic-tracer-aided studies of chemical residues in cotton seed, oil, feed and related products

International Nuclear Information System (INIS)

Qureshi, M.J.

1981-06-01

14 C-methyl and 14 C-ring-labelled carbaryl (1-naphthyl-N-methyl carbamate) were used to study the fate and magnitude of the insecticide in the plant and cotton seed products. Under conditions of actual agricultural practice, 0.08-0.09, 0.23-0.30 and 0.05 mg/kg of 14 C-residues were found in the seed, crude oil and cake respectively. In oil, the residue was resolved into 4 compounds, 2 identified as carbaryl and 1-naphthol. Residues from the soil did not exceed 0.3 mg/kg after the first week and declined to 0.1 mg/kg after 5 weeks. Parallel experiments were conducted under field conditions using 14 C-phenyl leptophos (4-bromo-2,5-dichlorophenyl methyl phenyl phosphorothioate). Leptophos residues were determined in the cotton seed products during 1975, 1976 and 1977, with mean values for leptophos residues in the cotton seed, crude oil and cake of 0.26, 1.10 and 0.07 mg/kg, respectively. Experiments with non-labelled monocrotophos [3-(dimethoxy phosphinyloxy)-N-methyl cis-crotonamide] gave residues of 0.30, 1.56 and 0.02 mg/kg in the seed, crude oil and cake, respectively. Carbaryl residues in two local maize varieties were determined by a colorimetric method. Cooking in aqueous, oil or aqueous-oil media led to 63-83% loss of carbaryl residues, after 30 minutes. Storage of corn oil for one year had essentially no effect on the concentration of carbaryl residues under laboratory conditions (presumably similar to regular storage conditions). An overall effect of simulated commercial processing procedures (saponification, deodorization and winterization) gave a loss of 70% of the original carbaryl in the oil. Commercial cooking procedures for national popular dishes resulted in near-complete elimination of carbaryl residues (up to 98%). Frying onions and potatoes in carbaryl-spiked corn oil for 3 min. up to 210 0 C resulted in 55-60% loss of the residue

Assessing food allergy risks from residual peanut protein in highly refined vegetable oil

NARCIS (Netherlands)

Blom, W.M.; Kruizinga, A.G.; Rubingh, C.M.; Remington, B.C.; Crevel, R.W.R.; Houben, G.F.

2017-01-01

Refined vegetable oils including refined peanut oil are widely used in foods. Due to shared production processes, refined non-peanut vegetable oils can contain residual peanut proteins. We estimated the predicted number of allergic reactions to residual peanut proteins using probabilistic risk

Estimation of polycyclic aromatic hydrocarbon concentrations in the water column based on tissue residues in mussels and salmon: An equilibrium partitioning approach

International Nuclear Information System (INIS)

Neff, J.M.; Burns, W.A.

1996-01-01

Equilibrium partitioning was used to estimate concentrations of dissolved polycyclic aromatic hydrocarbons (PAHs) in the water column from PAH residues in tissues of mussels and juvenile pink salmon collected from coastal marine waters affected by the Exxon Valdez oil spill. Estimated concentrations were within factors of 2 to 5 for fish and 5 to 10 for mussels of average total dissolved and particulate PAHs measured in concurrent water samples. Temporal trends of estimated and measured water-column PAH concentrations were comparable. Water-column PAH concentrations estimated from residues in tissues of mussels (Mytilus trossulus) were higher than estimates based on residues in tissues of juvenile pink salmon (Oncorhynchus gorbuscha). Possible reasons for this difference include seasonal variations in mussel lipid content, differences in PAH uptake and depuration rates between fish and mussels, differences in how fish and mussels interact with particulate oil, and possible short exposure times for juvenile pink salmon. All of these factors may play a role. In any event, estimates of dissolved PAHs in the water column, based on PAH residues in either fish or mussel tissue, confirm that PAH concentrations generally did not exceed water quality standards for protection of marine life

Effect of commercial processing procedures on 14C-LINDANE residues in corn oil

International Nuclear Information System (INIS)

Soliman, S.M.

2006-01-01

At blooming, maize plants were sprayed twice, 23 days apart, at a dose of 22 mg equivalent to 5 μCi/ plant. At post harvest, maize seeds had a radioactivity corresponding to 0.36% of the applied dose. The insecticide residues in crude oil, cake and methanolic extract were amounted to 8 % and 60 % 5 % , respectively, of original residues inside the seeds.The 14 C-activity in the crude oil could be reduced by commercial processes locally used for refining. The refined oil had a residue level of about 0.7 ppm mainly in the form of unchanged lindane in addition to a number of chloro phenols as main metabolites. Refining of corn oil fortified with 14 C-lindane led to a high reduction of 14 C-lindane (88%). The refined oil contained a residue consisting lindane and its chloro phenols

Construction of a predictive model for concentration of nickel and vanadium in vacuum residues of crude oils using artificial neural networks and LIBS.

Science.gov (United States)

Tarazona, José L; Guerrero, Jáder; Cabanzo, Rafael; Mejía-Ospino, E

2012-03-01

A predictive model to determine the concentration of nickel and vanadium in vacuum residues of Colombian crude oils using laser-induced breakdown spectroscopy (LIBS) and artificial neural networks (ANNs) with nodes distributed in multiple layers (multilayer perceptron) is presented. ANN inputs are intensity values in the vicinity of the emission lines 300.248, 301.200 and 305.081 nm of the Ni(I), and 309.310, 310.229, and 311.070 nm of the V(II). The effects of varying number of nodes and the initial weights and biases in the ANNs were systematically explored. Average relative error of calibration/prediction (REC/REP) and average relative standard deviation (RSD) metrics were used to evaluate the performance of the ANN in the prediction of concentrations of two elements studied here. © 2012 Optical Society of America

PREPARATION OF VARIOUS TYPES OF PULP FROM OIL PALM LIGNOCELLULOSIC RESIDUES

Institute of Scientific and Technical Information of China (English)

RyoheiTanaka; LehCheuPeng; WanRosliWanDaud

2004-01-01

Oil palm, Elaeis Guineensis, (Figure 1) is one of the most important plants in Malaysia. It produces palm oil and palm kernel oil, which is widely being used in food and other industries such as detergents and cosmetics. Malaysia is the world's largest producer and exporter of the oil, so that the country's economy is very much dependent on these oil products. Although oil from the palm tree is an excellent product for the country, residues from oil palm have not been used sufficiently. In this 10-15 years, development in new technologies for utilizing this lignocellulosic waste is categorized as one of the most important issues in science policy of Malaysia. Here we would like to introduce recent situation of palm oil and oil palm lignocellulosic residues at the first part of this paper. In the second part, our recent studies on the preparation of pulps for different purposes will be summarized.

Preparing hydraulic cement from oil-shale residue

Energy Technology Data Exchange (ETDEWEB)

1921-08-28

A process for preparation of hydraulic cement from oil-shale residue is characterized in that, as flux is used, rich-in-lime poor-in-sulfur portland-cement clinker, by which the usual gypsum addition, is avoided.

NMR and Chemometric Characterization of Vacuum Residues and Vacuum Gas Oils from Crude Oils of Different Origin

Directory of Open Access Journals (Sweden)

Jelena Parlov Vuković

2015-03-01

Full Text Available NMR spectroscopy in combination with statistical methods was used to study vacuum residues and vacuum gas oils from 32 crude oils of different origin. Two chemometric metodes were applied. Firstly, principal component analysis on complete spectra was used to perform classification of samples and clear distinction between vacuum residues and vacuum light and heavy gas oils were obtained. To quantitatively predict the composition of asphaltenes, principal component regression models using areas of resonance signals spaned by 11 frequency bins of the 1H NMR spectra were build. The first 5 principal components accounted for more than 94 % of variations in the input data set and coefficient of determination for correlation between measured and predicted values was R2 = 0.7421. Although this value is not significant, it shows the underlying linear dependence in the data. Pseudo two-dimensional DOSY NMR experiments were used to assess the composition and structural properties of asphaltenes in a selected crude oil and its vacuum residue on the basis of their different hydrodynamic behavior and translational diffusion coefficients. DOSY spectra showed the presence of several asphaltene aggregates differing in size and interactions they formed. The obtained results have shown that NMR techniques in combination with chemometrics are very useful to analyze vacuum residues and vacuum gas oils. Furthermore, we expect that our ongoing investigation of asphaltenes from crude oils of different origin will elucidate in more details composition, structure and properties of these complex molecular systems.

Laboratory studies of the properties of in-situ burn residues: chemical composition of residues

International Nuclear Information System (INIS)

Trudel, B.K.; Buist, I.A.; Schatzke, D.; Aurand, D.

1996-01-01

The chemical composition of the residue from small-scale burns of thick oil slicks was studied. The objective was to describe the changes in chemical composition in oils burning on water and to determine how these changes were influenced by the condition of the burn. Small-scale test burns involved burning 40-cm diameter pools of oil on water. A range of eight oil types including seven crude oils and an automotive diesel were burned. For each oil, slicks of fresh oil of three different thicknesses were tested. Two of the oils were tested before and after weathering. Results showed that the composition of the residue differed greatly from the parent oil. Asphaltenes, high-boiling-point aromatics and resins remained concentrated in the burn residue. The burning of slicks appeared to remove most of the lower-molecular weight aromatic hydrocarbons which included the more toxic and more bioavailable components of the crude oils. 11 refs., 6 tabs

Decrease of noxious emissions in the residual fuel oil combustion; Disminucion de emisiones nocivas en la combustion de aceite combustible residual

Energy Technology Data Exchange (ETDEWEB)

Mandoki W, Jorge [Econergia S. de R. L. de C. V. Mexico, D. F. (Mexico)

1994-12-31

The residual fuel oil combustion emits noxious substances such as carbonaceous particulate, nitrogen oxides, and sulfur trioxide at unacceptable levels. Water emulsified in the fuel substantially reduces such emissions, achieving besides, in most of the cases, a net saving in the fuel consumption. The beneficial effects are shown in burning the residual fuel oil as a water emulsion, as well as the method to produce an adequate emulsion. The emulsified fuel technology offers a low cost option to reduce air pollution. The fuel oil quality has been declining during the last decades due to: 1. Increase in the production of crude heavy oils, generally with higher content of asphaltens and sulfur. 2. Less availability of vacuum distillation residues due to its conversion into greater value products. 3. More intensive conversion processes such as catalytic cracking, visbreaking, etc. that increase the asphaltenes concentration in the bottoms, causing instability problems. 4. The increase in the vanadium and other metals content as the concentration of asphaltenes increases. The use of emulsified fuel oil provides an efficient and economical method to substantially reduce the noxious emissions to the atmosphere. The emulsion contains water particles in a diameter between 2 and 20 microns, uniformly distributed in the fuel oil, generally in a proportion generally of 5 to 10%; besides, it contains a tensioactive agent to assure a stable emulsion capable of withstanding the shearing forces of the pumping and distribution systems. When the atomized oil drops get into the combustion chamber, the emulsified water flashes into high pressure steam, originating a violent secondary atomization. The effect of this secondary atomization is the rupture of the oil drops of various hundred microns, producing drops of 5 to 15 microns in diameter. Since the necessary time for combustion is an exponential function of the drop diameter, a very substantial improvement in the combustion is

Radionuclide concentrations in oil extraction and production processes in Northeast Brazil

International Nuclear Information System (INIS)

Gazineu, Maria Helena Paranhos

2005-06-01

Since the beginning of the twentieth century the presence of naturally occurring radioactive material (NORM) was detected in the water and oil extracted from wells both onshore and offshore. The oil is extracted together with water and sediments which contain radionuclides of the uranium and thorium series. Among the radionuclides present, especial attention should be given to 226 Ra and 228 Ra, due to its long half-life and importance, from the radiological point of view. The objective of this work was to identify the natural radionuclides in the oil industry, to determine their activity concentration, and from these results, to evaluate the risks the employees of the oil industry are exposed to. Samples of sludge, scale and produced water extracted with the oil were collected from three oil processing stations in the state of Sergipe, Brazil. The activity concentrations of the radionuclides were determined in the solid samples before and after the extraction of the oil. The chemical and mineralogical composition of the samples without oil was evaluated. Water samples, on the other hand, were analyzed for their contents of radionuclides and barium concentration. It was observed that the activity concentrations of the analyzed radionuclides ( 226 Ra, 228 Ra, 228 Th and 210 Pb) in sludge and scales were very high when compared with the literature, particularly much higher than the values for 226 Ra and 228 Ra obtained for sludge and scales from the oil platforms near the city of Campos, state of Rio de Janeiro. The maximum concentration values for 226 Ra, 228 Ra, 228 Th and 210 Pb (3,500, 2,195, 2,248.6 and 201 kBq kg -1 , respectively) were obtained for the scales after the extraction of the oil. The analysis of the samples showed that barium sulphate (barite) and strontium sulphate (celestite) are the main constituents of the scales, while carbonates and silicates, together with other compounds are the components of sludge. A correlation between barium, 226 Ra and

Evaluation of PAH depletion of subsurface Exxon Valdez oil residues remaining in Prince William Sound in 2007-2008 and their likely bioremediation potential

Energy Technology Data Exchange (ETDEWEB)

Atlas, R. [Louisville Univ., Louisville, KY (United States); Bragg, J.R. [Creative Petroleum Solutions LLC, Houston, TX (United States)

2009-07-01

This study examined the extent of oil weathering at the Exxon Valdez oil spill (EVOS) sites and estimated the bioremediation potential for shoreline segments by examining the depletion of total polycyclic aromatic hydrocarbons (PAHs) relative to an estimated applicability threshold of 70 per cent. The distribution of oil was examined by location and current ratios of nitrogen and non-polar oil in order to assess if biodegradation rates were nutrient-limited. The impact of sequestration on the effectiveness of bioremediation was also studied. Results of the study showed that the EVOS residues are patchy and infrequently found on sites that were heavily oiled in 1989. Only 0.4 per cent of the oil originally stranded in 1989 remained. The remaining EVOS residues are sequestered under boulder and cobble armour in areas with limited contact with flowing water. The study also showed that concentrations of nitrogen and dissolved oxygen in pore waters within strata adjacent to the sequestered oil can support biodegradation. Most remaining EVOS residues are highly weathered and biodegraded. It was concluded that nutrients added to the shorelines are unlikely to effectively contact the sequestered oil. 31 refs., 2 tabs., 14 figs.

DEVELOPMENT OF BIOSURFACTANT-MEDIATED OIL RECOVERY IN MODEL POROUS SYSTEMS AND COMPUTER SIMULATIONS OF BIOSURFACTANT-MEDIATED OIL RECOVERY

Energy Technology Data Exchange (ETDEWEB)

M.J. McInerney; S.K. Maudgalya; R. Knapp; M. Folmsbee

2004-05-31

Current technology recovers only one-third to one-half of the oil that is originally present in an oil reservoir. Entrapment of petroleum hydrocarbons by capillary forces is a major factor that limits oil recovery (1, 3, 4). Hydrocarbon displacement can occur if interfacial tension (IFT) between the hydrocarbon and aqueous phases is reduced by several orders of magnitude. Microbially-produced biosurfactants may be an economical method to recover residual hydrocarbons since they are effective at low concentrations. Previously, we showed that substantial mobilization of residual hydrocarbon from a model porous system occurs at biosurfactant concentrations made naturally by B. mojavensis strain JF-1 if a polymer and 2,3-butanediol were present (2). In this report, we include data on oil recovery from Berea sandstone experiments along with our previous data from sand pack columns in order to relate biosurfactant concentration to the fraction of oil recovered. We also investigate the effect that the JF-2 biosurfactant has on interfacial tension (IFT). The presence of a co-surfactant, 2,3-butanediol, was shown to improve oil recoveries possibly by changing the optimal salinity concentration of the formulation. The JF-2 biosurfactant lowered IFT by nearly 2 orders of magnitude compared to typical values of 28-29 mN/m. Increasing the salinity increased the IFT with or without 2,3-butanediol present. The lowest interfacial tension observed was 0.1 mN/m. Tertiary oil recovery experiments showed that biosurfactant solutions with concentrations ranging from 10 to 60 mg/l in the presence of 0.1 mM 2,3-butanediol and 1 g/l of partially hydrolyzed polyacrylamide (PHPA) recovered 10-40% of the residual oil present in Berea sandstone cores. When PHPA was used alone, about 10% of the residual oil was recovered. Thus, about 10% of the residual oil recovered in these experiments was due to the increase in viscosity of the displacing fluid. Little or no oil was recovered at

Biodiesel Production from Residual Palm Oil Contained in Spent Bleaching Earth by In Situ Trans-Esterification

Directory of Open Access Journals (Sweden)

A S Fahmil QRM

2014-06-01

Full Text Available Spent Bleaching Earth (SBE is an industrial solid waste of vegetable oil industry that has a high residual oil to be potentialy converted to biodiesel. This study aims at developing a biodiesel production process technology by utilizing residual palm oil contained in SBE and to test the use of hexane in the trans-esterification process. Optimization process was done by using the Response Surface Method (RSM. The variables studied included catalyst concentration and reaction time. On the other hand, the deoiled SBE resulted from biodiesel production was tested as an adsorbent on biodiesel purification after being reactivated. The method used in the biodiesel production included an in situ acid catalysed esterification followed by in situ base catalysed trans-esterification. The results of RSM showed that the optimum process was obtained at NaOH concentration of 1.8% and reaction time of 104.73 minutes, with a predicted response rate of 97.18% and 95.63% for validation results. The use of hexane could also increase the yield of biodiesel which was obtained on the ratio of hexane to methanol of 0.4:1 (volume of hexane: volume of methanol. On the other hand, the reactivated bleaching earth was effective as an adsorbent in biodiesel production, which was still conform with the Indonesian National Standard.

Radiotracer studies on the fate and transformation of pesticide residues in the environment and food chains. Part of a coordinated programme on isotopic-tracer-aided studies of chemical residues in cotton seed, feed, oil and related products

International Nuclear Information System (INIS)

Lee, S.R.

1980-10-01

The magnitude and fate of some pesticide chemicals in Korean foods were studied with particular reference to oil-bearing crops and related products. Application of the chemicals was made under conditions of actual agricultural practice. Analytical methodologies included nuclear activation, gas chromatographic, spectrophotometric and radiotracer techniques. Residues of benzene hexachloride, heptachlor, heptachlor epoxide, aldrin, dieldrin, endrin and DDT found in refined vegetable oil samples were below or within the tolerance limits set by international organizations and as such, these are unlikely to present any toxicological hazard to the consumer. Also, residues of the herbicides nitrogen, alachlor and butachlor applied to oil-bearing crops were not detected in the seeds. Studies on 14 C-BHC residues in rice revealed that polishing and washing play an important role in removing a considerable portion of the residue. Data on the arsenic-containing neoasozine residues suggest that the products consumed by the human (grain and oil) contained residues below the tolerance limit and are unlikely to present any toxicological hazard to the consumer. On the other hand, relatively high arsenic concentrations (2.2 mg/kg) were found in the cake (serving as animal feed) and should be carefully evaluated in the light of toxicological data

Rhizosphere biodegradation of xenobiotics: Microbiological study of a rice field polluted by oil refinery residues

Energy Technology Data Exchange (ETDEWEB)

Rasolomanana, J.L.; Balandreau, J.

1987-07-01

A rice field had been studied in which the disposal of oil residues from a refinery plant seemed to improve rice growth and soil N content. To check the hypothesis that nitrogen fixation by oil-adapted bacteria could explain this observation we isolated and studied dominant diazotrophic bacteria from the rhizosphere of an actively N/sub 2/-fixing rice plant growing on the polluted soil; for this purpose we used an axenic plant as an enrichment step. The rhizosphere did not contain more than 10/sup 5/ N/sub 2/-fixing bacteria per g dry soil, essentially Bacillus polymyxa; one of the isolates, strain R3 could grow and reduce C/sub 2/H/sub 2/ on oil residues only in the presence of glucose or of exudates from an axenic plant (spermosphere model); the presence of R3 diminished the inhibition of rice growth due to the oil residues; R3 nitrogenase activity in the rhizosphere of rice was increased in the presence of these residues. This cometabolism of oil residues in the presence of exudates and their stimulating effect on N/sub 2/ fixation provide a likely explanation for observed positive effects of the disposal of oil residues on arable lands, and are conducive to the hypothesis that rhizosphere cometabolism could greatly enhance soil organic matter turn over and humification rates.

Production of petroleum bitumen by oxidation of heavy oil residue with sulfur

Science.gov (United States)

Tileuberdi, Ye.; Akkazyn, Ye. A.; Ongarbayev, Ye. K.; Imanbayev, Ye. I.; Mansurov, Z. A.

2018-03-01

In this paper production of bitumen adding elemental sulfur at oxidation of oil residue are investigated. The objects of research were distilled residue of Karazhanbas crude oil and elemental sulfur. These oil residue characterized by a low output of easy fractions and the high content of tar-asphaltene substances, therefore is the most comprehensible feedstock for producing bitumen. The sulfur is one of the oil product collected in oil extraction regions. Oxidation process of hydrocarbons carried out at temperatures from 180 up to 210 °С without addition of sulfur and with the addition of sulfur (5-10 wt. %) for 4 hours. At 200 °С oxidation of hydrocarbons with 5, 7 and 10 wt.% sulfur within 3-4 h allows receiving paving bitumen on the mark BND 200/300, BND 130/200, BN 90/130 and BN 70/30. Physical and mechanical characteristics of oxidation products with the addition of 5-7 wt. % sulfur corresponds to grade of paving bitumen BND 40/60. At the given temperature oxidized for 2.5-3 h, addition of 10 wt. % sulfur gave the products of oxidation describing on parameters of construction grades of bitumen (BN 90/10).

Prediction of Hexaconazole Concentration in the Top Most Layer of Oil Palm Plantation Soil Using Exploratory Data Analysis (EDA).

Science.gov (United States)

Maznah, Zainol; Halimah, Muhamad; Shitan, Mahendran; Kumar Karmokar, Provash; Najwa, Sulaiman

2017-01-01

Ganoderma boninense is a fungus that can affect oil palm trees and cause a serious disease called the basal stem root (BSR). This disease causes the death of more than 80% of oil palm trees midway through their economic life and hexaconazole is one of the particular fungicides that can control this fungus. Hexaconazole can be applied by the soil drenching method and it will be of interest to know the concentration of the residue in the soil after treatment with respect to time. Hence, a field study was conducted in order to determine the actual concentration of hexaconazole in soil. In the present paper, a new approach that can be used to predict the concentration of pesticides in the soil is proposed. The statistical analysis revealed that the Exploratory Data Analysis (EDA) techniques would be appropriate in this study. The EDA techniques were used to fit a robust resistant model and predict the concentration of the residue in the topmost layer of the soil.

Characterization of virgin walnut oils and their residual cakes produced from different varieties.

Science.gov (United States)

Ojeda-Amador, Rosa M; Salvador, María Desamparados; Gómez-Alonso, Sergio; Fregapane, Giuseppe

2018-06-01

This study addresses the composition and properties of different walnut varieties (Chandler, Hartley and Lara), in particular their virgin oils and residual cakes obtained by screw pressing employing different cultivars. Among nuts, walnut (Juglans regia L.) exhibits interesting nutritional value, mainly due to their high content in linoleic acid, phenolic and tocopherol compounds, which show antioxidant and other healthy properties. Valuable results related to fatty acid profile and minor components were observed. Virgin walnut oil is a rich source in linoleic acid (60-62%) and γ-tocopherol (517-554 mg/kg). Moreover, walnuts show a very high content in total phenolic compounds (10,045-12,474 mg/kg; as gallic acid), which contribute to a great antioxidant activity (105-170 mmol/kg for DPPH, and 260-393 mmol/kg for ORAC), being the hydrolysable tannins (2132-4204 mg/kg) and flavanols (796-2433 mg/kg) their main phenolic groups. Aldehydes account for the highest contribution to aromatic volatiles in virgin walnut oil (about 35% of total). As expected, polar phenolic compounds concentrate in the residual cake, after the separation of the oily phase, reaching a content of up to 19,869 mg/kg, leading to potential added value and applications as source of bioactive compounds to this by-product. Copyright © 2018 Elsevier Ltd. All rights reserved.

Residues in cottonseed oil and cake resulting from the combined application of DDT and dimethoate

International Nuclear Information System (INIS)

El Zorgani, G.A.; Ahmed, M.M.

1981-01-01

Cotton plants were treated with a combination of DDT and dimethoate under conditions of local agricultural practice to study the fate and magnitude of both chemicals in the cottonseed and related products. GLC and nuclear (using 14 C-DDT) techniques were used. DDT residues in the crude oil averaged 0.115 mg/kg; mainly as p,p'-DDT while residues in the cake were not detected. Dimethoate and dimethoxon in the crude oil were 0.13 and 0.01 mg/kg respectively. The cake contained 0.14 mg/kg dimethoate and 0.01 mg/kg dimethoxon. By simulating commercial oil processing in the laboratory using 14 C-DDT fortified oil samples it was found that alkali treatment and bleaching removed only 7% of the total residue, while deodorization effected removal of 40-50% of the residue. (author)

Enhancement of recovery of residual oil using a biosurfactant slug ...

African Journals Online (AJOL)

Characterization of the biosurfactant extract revealed a mixture of glycolipid and phospholipid in a ratio of 3.35:1. The irreducible water saturation (Swi) and initial residual oil saturation (Sor) of the sand-pack were 0.280 ± 0.003 and 0.373 ± 0.006, respectively. Core flooding experiment showed that an optimum oil recovery ...

Biodiesel of distilled hydrogenated fat and biodiesel of distilled residual oil: fuel consumption in agricultural tractor

Energy Technology Data Exchange (ETDEWEB)

Camara, Felipe Thomaz da; Lopes, Afonso; Silva, Rouverson Pereira da; Oliveira, Melina Cais Jejcic; Furlani, Carlos Eduardo Angeli [Universidade Estadual Paulista (UNESP), Jaboticabal, SP (Brazil); Dabdoub, Miguel Joaquim [Universidade de Sao Paulo (USP), Ribeirao Preto (Brazil)

2008-07-01

Great part of the world-wide oil production is used in fry process; however, after using, such product becomes an undesirable residue, and the usual methods of discarding of these residues, generally contaminate the environment, mainly the rivers. In function of this, using oil and residual fat for manufacturing biodiesel, besides preventing ambient contamination, turning up an undesirable residue in to fuel. The present work had as objective to evaluate the fuel consumption of a Valtra BM100 4x2 TDA tractor functioning with methylic biodiesel from distilled hydrogenated fat and methylic biodiesel from distilled residual oil, in seven blends into diesel. The work was conducted at the Department of Agricultural Engineering, at UNESP - Jaboticabal, in an entirely randomized block statistical design, factorial array of 2 x 7, with three repetitions. The factors combinations were two types of methylic distilled biodiesel (residual oil and hydrogenated fat) and seven blends (B{sub 0}, B{sub 5}, B{sub 1}5, B{sub 2}5, B{sub 5}0, B{sub 7}5 and B{sub 1}00). The results had evidenced that additioning 15% of biodiesel into diesel, the specific consumption was similar, and biodiesel of residual oil provided less consumption than biodiesel from hydrogenated fat. (author)

Assessment of bioavailability of weathered oil residues using caged bivalves (Crassostrea gigas and Mytilus edulis) as indicator organisms

International Nuclear Information System (INIS)

Bleczinski, C.F.; Costa, H.J.; Rigatti, M.J.; Wong, M.C.; Boehm, P.D.

1993-01-01

In April 1988, an estimated 400,000 gallons of San Joaquin Valley crude oil spilled into Peyton Slough and subsequently into Suisun Bay from an oil refinery in Martinez, California. The crude oil initially impacted a number of ecologically sensitive environments including estuarine water, marsh grasses, marsh and shoreline sediment, and intertidal sediment. A four-year oil weathering study was performed to determine the concentrations of environmentally important compounds in the stranded oil, to monitor changes in these concentrations over time, and to assess the potential long-term impact of the spilled oil in these various environments. As a result of marked differences in the rate of weathering at the different sites, a bioaccumulation component was added to the original study design in order to assess the bioavailability of crude oil residues remaining four-years post spill. Caged bivalves (Crassostrea gigas and Mytilus edulis) were deployed at the three study sites as sentinel organisms and exposed for three months. Sediments and organism tissues were analyzed using gas chromatography/mass spectrometry for polynuclear aromatic hydrocarbon (PAH) assemblages characteristics of the spilled oil. Advanced hydrocarbon fingerprinting techniques (e.g., double ratio plots of characteristic alkyl PAHs) were used to match distributions in the organisms and in the study site sediments

PREPARATION OF VARIOUS TYPES OF PULP FROM OIL PALM LIGNOCELLULOSIC RESIDUES

Institute of Scientific and Technical Information of China (English)

Ryohei Tanaka; Leh Cheu Peng; Wan Rosli Wan Daud

2004-01-01

@@ INTRODUCTION Oil palm, Elaeis Guineensis, (Figure 1) is one of the most important plants in Malaysia. It produces palm oil and palm kernel oil, which is widely being used in food and other industries such as detergents and cosmetics. Malaysia is the world′s largest producer and exporter of the oil, so that the country′s economy is very much dependent on these oil products. Although oil from the palm tree is an excellent product for the country, residues from oil palm have not been used sufficiently. In this 10～15 years, development in new technologies for utilizing this lignocellulosic waste is categorized as one of the most important issues in science policy of Malaysia.

proximate and ultimate analysis of fuel pellets from oil palm residues

African Journals Online (AJOL)

HOD

Keywords: Oil Palm Residues, Fuel Pellets, Proximate Analysis, Ultimate Analysis. 1. INTRODUCTION ... Pelletizing of this biomass resources into pellets is a way of ensuring a ... demand for pellets [3], and alternative feed-stocks such as palm kernel ... agro-residues, selection of the best pellets has to be made based on ...

Prediction of Hexaconazole Concentration in the Top Most Layer of Oil Palm Plantation Soil Using Exploratory Data Analysis (EDA.

Directory of Open Access Journals (Sweden)

Zainol Maznah

Full Text Available Ganoderma boninense is a fungus that can affect oil palm trees and cause a serious disease called the basal stem root (BSR. This disease causes the death of more than 80% of oil palm trees midway through their economic life and hexaconazole is one of the particular fungicides that can control this fungus. Hexaconazole can be applied by the soil drenching method and it will be of interest to know the concentration of the residue in the soil after treatment with respect to time. Hence, a field study was conducted in order to determine the actual concentration of hexaconazole in soil. In the present paper, a new approach that can be used to predict the concentration of pesticides in the soil is proposed. The statistical analysis revealed that the Exploratory Data Analysis (EDA techniques would be appropriate in this study. The EDA techniques were used to fit a robust resistant model and predict the concentration of the residue in the topmost layer of the soil.

Effect of the inclusion of fish residue oils in diets on the fatty acid profile of muscles of males and females lambari (Astyanax altiparanae

Directory of Open Access Journals (Sweden)

Ligia Uribe Gonçalves

2012-09-01

Full Text Available This study evaluated the effects of two lipids sources of fish residue (tilapia and salmon compared with a vegetable oil source (soybean oil on the fatty acid profiles of male and female lambari. This experiment was developed in a completely randomized experimental design in a 3 × 2 factorial arrangement, totaling 6 treatments resulting from the combination of the three experimental diets for both sexes, with four replications for each treatment. This study involved 120 male (2.58±0.13 g and 72 female lambari (4.00±0.09 g, fed the experimental diets twice a day until apparent satiation for a period of 60 days. Oleic, linoleic, palmitic and stearic fatty acids were found at higher concentrations in all experimental oils and diets, as well in the muscle of male and female lambari. The low amounts of arachidonic, eicosapentaenoic and docosahexaenoic acids in the experimental diets and subsequent greater concentrations in muscle tissue, suggested that lambari are able to desaturate and elongate the chain of fatty acids with 18 carbons. The fish of both sexes that received the diet with soybean oil showed high levels of n-6 fatty acids, especially of C18: 2n-6 and low levels of eicosapentaenoic and docosahexaenoic acids. The diet with salmon residue oil promoted higher levels of fatty acids of the n-3 series and resulted in the best n-3/n-6 ratio in the muscle of male and female lambari. The oils from fish residues can be a substitute for traditional fish oil and its use in the lambari diets does not impair its growth.

Decomposition of residual oil by large scale HSC plant

Energy Technology Data Exchange (ETDEWEB)

Washimi, Koichi; Ogata, Yoshitaka; Limmer, H.; Schuetter, H. (Toyo Engineering Corp., funabashi, Japan VEB Petrolchemisches Kombinat Schwedt, Schwedt (East Germany))

1989-07-01

Regarding large scale and high decomposition ratio visbreaker HSC, characteristic points and operation conditions of a new plant in East Germany were introduced. As for the characteristics of the process, high decomposition ratio and stable decpmposed oil, availability of high sulfur content oil or even decomposed residuum of visbreaker, stableness of produced light oil with low content of unsaturated components, low investment with low running cost, were indicated. For the realization of high decomposition ratio, designing for suppressing the decomposition in heating furnace and accelaration of it in soaking drum, high space velocity of gas phase for better agitation, were raised. As the main subject of technical development, design of soaking drum was indicated with main dimensions for the designing. Operation conditions of the process in East Germany using residual oil supplied from already working visbreaker for USSR crude oil were introduced. 6 refs., 4 figs., 2 tabs.

Effect of oil refining processes on 14 C-tetrachlorvinphos residues in soya bean oil

International Nuclear Information System (INIS)

Farghaly, M.; Zayed, S.M.A.D.

1986-01-01

Crude soya bean oil extracted from grains treated with 14 C-tetrachlorvinphos and stored for 30 weeks was subjected to different refining processes. The effect of commercial refining processes, namely: alkali treatment, bleaching, winterization and deodorization on the nature and magnitude of the originally present residues was investigated. A high percentage (52%) of the residues was eliminated during alkali neutralization. No potentially toxic materials were detected among the identified degradation products. The obtained data showed that the ultimate degradation products were dimethyl phosphate and mono methyl phosphate.2 tab.,2 scheme

MODEL FOR THE CORRECTION OF THE SPECIFIC GRAVITY OF BIODIESEL FROM RESIDUAL OIL

Directory of Open Access Journals (Sweden)

Tatiana Aparecida Rosa da Silva

2013-06-01

Full Text Available Biodiesel is a important fuel with economic benefits, social and environmental. The production cost of the biodiesel can be significantly lowered if the raw material is replaced by a alternative material as residual oil. In this study, the variation of specific gravity with temperature increase for diesel and biodiesel from residual oil obtained by homogeneous basic catalysis. All properties analyzed for biodiesel are within specification Brazil. The determination of the correction algorithm for the specific gravity function of temperature is also presented, and the slope of the line to diesel fuel, methylic biodiesel (BMR and ethylic biodiesel (BER from residual oil were respectively the values -0.7089, -0.7290 and -0.7277. This demonstrates the existence of difference of the model when compared chemically different fuels, like diesel and biodiesel from different sources, indicating the importance of determining the specific algorithm for the operations of conversion of volume to the reference temperature.

Catalyst systems in the production of biodiesel from residual oil; Sistemas cataliticos na producao de biodiesel por meio de oleo residual

Energy Technology Data Exchange (ETDEWEB)

Souza, Carlos Alexandre de [Universidade Federal de Itajuba (UNIFEI), MG (Brazil)

2006-07-01

The vegetable oils and fat animals appear like an alternative for substitution the diesel oil in ignition engines for compression. Submitting the oil on transesterification reaction, we obtain a fuel with same characteristics as diesel, called biodiesel. Generally, 85 per cent of biodiesel cost is from the oil production. Through transesterification vegetable oil can be transformed in a mixture of esters of fatty acids. The residual oil from frying has been used as a possibility of raw materials of biodiesel, due to its easy acquisition and the viability of not being discarded as waste. (author)

Natural radioactivity in petroleum residues

International Nuclear Information System (INIS)

Gazineu, M.H.P.; Gazineu, M.H.P.; Hazin, C.A.; Hazin, C.A.

2006-01-01

The oil extraction and production industry generates several types of solid and liquid wastes. Scales, sludge and water are typical residues that can be found in such facilities and that can be contaminated with Naturally Occurring Radioactive Material (N.O.R.M.). As a result of oil processing, the natural radionuclides can be concentrated in such residues, forming the so called Technologically Enhanced Naturally Occurring Radioactive Material, or T.E.N.O.R.M.. Most of the radionuclides that appear in oil and gas streams belong to the 238 U and 232 Th natural series, besides 40 K. The present work was developed to determine the radionuclide content of scales and sludge generated during oil extraction and production operations. Emphasis was given to the quantification of 226 Ra, 228 Ra and 40 K since these radionuclides,are responsible for most of the external exposure in such facilities. Samples were taken from the P.E.T.R.O.B.R.A.S. unity in the State of Sergipe, in Northeastern Brazil. They were collected directly from the inner surface of water pipes and storage tanks, or from barrels stored in the waste storage area of the E and P unit. The activity concentrations for 226 Ra, 228 Ra and 40 K were determined by using an HP Ge gamma spectrometric system. The results showed concentrations ranging from 42.7 to 2,110.0 kBq/kg for 226 Ra, 40.5 to 1,550.0 kBq/kg for 228 Ra, and 20.6 to 186.6 kBq/kg for 40 K. The results highlight the importance of determining the activity concentration of those radionuclides in oil residues before deciding whether they should be stored or discarded to the environment. (authors)

Development of a field testing protocol for identifying Deepwater Horizon oil spill residues trapped near Gulf of Mexico beaches

Science.gov (United States)

Han, Yuling

2018-01-01

The Deepwater Horizon (DWH) accident, one of the largest oil spills in U.S. history, contaminated several beaches located along the Gulf of Mexico (GOM) shoreline. The residues from the spill still continue to be deposited on some of these beaches. Methods to track and monitor the fate of these residues require approaches that can differentiate the DWH residues from other types of petroleum residues. This is because, historically, the crude oil released from sources such as natural seeps and anthropogenic discharges have also deposited other types of petroleum residues on GOM beaches. Therefore, identifying the origin of these residues is critical for developing effective management strategies for monitoring the long-term environmental impacts of the DWH oil spill. Advanced fingerprinting methods that are currently used for identifying the source of oil spill residues require detailed laboratory studies, which can be cost-prohibitive. Also, most agencies typically use untrained workers or volunteers to conduct shoreline monitoring surveys and these worker will not have access to advanced laboratory facilities. Furthermore, it is impractical to routinely fingerprint large volumes of samples that are collected after a major oil spill event, such as the DWH spill. In this study, we propose a simple field testing protocol that can identify DWH oil spill residues based on their unique physical characteristics. The robustness of the method is demonstrated by testing a variety of oil spill samples, and the results are verified by characterizing the samples using advanced chemical fingerprinting methods. The verification data show that the method yields results that are consistent with the results derived from advanced fingerprinting methods. The proposed protocol is a reliable, cost-effective, practical field approach for differentiating DWH residues from other types of petroleum residues. PMID:29329313

Development of a field testing protocol for identifying Deepwater Horizon oil spill residues trapped near Gulf of Mexico beaches.

Science.gov (United States)

Han, Yuling; Clement, T Prabhakar

2018-01-01

The Deepwater Horizon (DWH) accident, one of the largest oil spills in U.S. history, contaminated several beaches located along the Gulf of Mexico (GOM) shoreline. The residues from the spill still continue to be deposited on some of these beaches. Methods to track and monitor the fate of these residues require approaches that can differentiate the DWH residues from other types of petroleum residues. This is because, historically, the crude oil released from sources such as natural seeps and anthropogenic discharges have also deposited other types of petroleum residues on GOM beaches. Therefore, identifying the origin of these residues is critical for developing effective management strategies for monitoring the long-term environmental impacts of the DWH oil spill. Advanced fingerprinting methods that are currently used for identifying the source of oil spill residues require detailed laboratory studies, which can be cost-prohibitive. Also, most agencies typically use untrained workers or volunteers to conduct shoreline monitoring surveys and these worker will not have access to advanced laboratory facilities. Furthermore, it is impractical to routinely fingerprint large volumes of samples that are collected after a major oil spill event, such as the DWH spill. In this study, we propose a simple field testing protocol that can identify DWH oil spill residues based on their unique physical characteristics. The robustness of the method is demonstrated by testing a variety of oil spill samples, and the results are verified by characterizing the samples using advanced chemical fingerprinting methods. The verification data show that the method yields results that are consistent with the results derived from advanced fingerprinting methods. The proposed protocol is a reliable, cost-effective, practical field approach for differentiating DWH residues from other types of petroleum residues.

Characterization of enzymatically extracted sunflower seed oil as well as the protein residues

Directory of Open Access Journals (Sweden)

Sitohy, M. Z.

1993-12-01

Full Text Available Sunflower seed oil was enzymatically extracted with six different enzymes: cellulase, hemicellulase, animal proteinase, acid proteinase, pectinase and pectinex under the following conditions: substrate concentration in phosphate buffer (0.5M, pH 5 30%, enzyme concentration 2% (E/S, temperature 50°C and time 3 hours. The obtained oils were analyzed for physicochemical properties and fatty acid profiles. The protein residues were analyzed for amino acid compositions. The results showed that the enzymatic extraction with cellulase or hemicellulase could maintain good oil quality of the extracted oils as their levels of linoleic and oleic acids recorded similar values to those of the control oil extracted with organic solvents. Also the level of iodine value was in the same level of control. On the other hand, the use of proteases in the enzymatic extraction of sunflower seed oil caused some reductions in the levels of the unsaturated fatty acids as well as the iodine value. The pectinases showed a similar trend to that of the proteinase with the least recovery of linoleic acid among the different oils under study. Similarly, the use of cellulases did not change the amino acid composition of the protein residue as compared to the control, in the contrary to the extraction with the proteinases which caused reduction of some amino acids from the protein residues especially lysine, leucine, iso-leucine, alanine, arginine and aspartic. In that respect the use of pectinases behaved similar to cellulases.

Aceite de semilla de girasol fue extraído enzimáticamente con seis enzimas diferentes: celulasa, hemicelulasa, proteinasa animal, proteinase acida, pectinasa y pectinex bajo las condiciones siguientes: concentración de sustrato en tampón fosfato (0,5M, pH 5 30%, concentración enzimática 2% (E/S, temperatura 50°C y tiempo 3 horas. Los aceites obtenidos fueron analizados por sus propiedades fisicoquímicas y perfiles de ácidos grasos

AN ALTERNATIVE APPROACH TO THE USE OF HEAVY OIL RESIDUE

Directory of Open Access Journals (Sweden)

Eugene Dashut

2013-01-01

Full Text Available We consider an alternative approach to the existing oil refining, in which instead of a single priority that emerged in the traditional approach, we consider two: get the light component and a heavy residue used for the production of new construction materials.

Compositional changes of aromatic steroid hydrocarbons in naturally weathered oil residues in the Egyptian western desert

International Nuclear Information System (INIS)

Barakat, A.O.; Qian, Y.; Kim, M.; Kennicutt, M.C. II

2002-01-01

Aromatic steranes are geochemical markers that can be used to study the maturation of organic matter of sediments and to correlate crude oils and source rocks. In this study, naturally weathered oil residues from an arid waste disposal site in Al-Alamein, Egypt, were analyzed for monoaromatic and triaromatic steranes to show the usefulness of biomarker compounds in assessing changes in chemical composition during the degradation of oil residues that have been released onto terrestrial environments. Gas chromatography and mass spectrometry were used to characterize the individual aromatic compounds. Results indicate that triaromatic sterane distributions are similar in oil residues with varying extents of weathering. The distribution correlated with a fresh crude oil sample from Western Desert-sourced oil. Molecular ratios of triaromatic sterane compounds were found to be suitable for source identification. The major changes in chemical compositions resulting from the weathering of the oil included the depletion of short chain mono- and tri-aromatic steranes in extremely weathered samples. The results of the triaromatic sterane distribution correspond with weathering classifications based on the analyses of saturated and aromatic hydrocarbons and the ratios of n-alkanes, polycyclic aromatic hydrocarbons, and saturate biomarker compounds. 15 refs., 3 tabs., 3 figs

Asphalts tests using onshore drilling oil wells residues; Ensaios asfalticos utilizando residuos de perfuracao onshore

Energy Technology Data Exchange (ETDEWEB)

Lucena, Adriano Elisio de F.L.; Rodrigues, John Kennedy G.; Ferreira, Heber Carlos; Lucena, Leda Christiane de F.L. [Universidade Federal de Campina Grande (UFCG), PB (Brazil); Lucena, Luciana de F.L. [Faculdade de Ciencias Sociais Aplicada (FACISA), Campina Grande, PB (Brazil)

2008-07-01

The drilling cuttings are one of the residues produced by the oils industries in large amounts during the drilling of oil wells. An alternative of final disposal of the drilling cutting residue is its utilization in asphalt mixtures. Based on this alternative, it was realized chemical and granulometric analysis and tests (Marshall and indirect tensile strength), on the asphaltic mixture using the residue from the oil drilling wells (well: 1-POTI-4-RN, located at Governador DIX-Sept Rosado - RN - Brazil). The achieved results to Marshall test indicated that for the analyzed mixture, the ideal content of residue that can be incorporated to the asphaltic composition and attend at the DNIT-ES 31 (2006) is 5%. To the indirect tensile strength test, the results showed a strength value higher than the minimum limit requested by the DNIT (0,65 MPa). The achieved results indicated the possibility of the utilization of the drilling cuttings in asphaltic pavements as fine aggregate, obeying the percentage limits, as an alternative to the final disposal. (author)

Microbial Physiology of the Conversion of Residual Oil to Methane: A Protein Prospective

Science.gov (United States)

Morris, Brandon E. L.; Bastida-Lopez, Felipe; von Bergen, Martin; Richnow, Hans-Hermann; Suflita, Joseph M.

2010-05-01

Traditional petroleum recovery techniques are unable to extract the majority of oil in most petroliferous deposits. The recovery of even a fraction of residual hydrocarbon in conventional reserves could represent a substantive energy supply. To this end, the microbial conversion of residual oil to methane has gained increasing relevance in recent years [1,2]. Worldwide demand for methane is expected to increase through 2030 [3], as it is a cleaner-burning alternative to traditional fuels [4]. To investigate the microbial physiology of hydrocarbon-decomposition and ultimate methanogenesis, we initiated a two-pronged approach. First, a model alkane-degrading sulfate-reducing bacterium, Desulfoglaeba alkanexedens, was used to interrogate the predominant metabolic pathway(s) differentially expressed during growth on either n-decane or butyrate. A total of 81 proteins were differentially expressed during bacterial growth on butyrate, while 100 proteins were unique to the alkane-grown condition. Proteins related to alkylsuccinate synthase, or the homologous 1-methyl alkylsuccinate synthase, were identified only in the presence of the hydrocarbon. Secondly, we used a newly developed stable isotope probing technique [5] targeted towards proteins to monitor the flux of carbon through a residual oil-degrading bacterial consortium enriched from a gas-condensate contaminated aquifer [1]. Combined carbon and hydrogen stable isotope fractionation identified acetoclastic methanogenesis as the dominant process in this system. Such findings agree with the previous clone library characterization of the consortium. Furthermore, hydrocarbon activation was determined to be the rate-limiting process during the net conversion of residual oil to methane. References 1. Gieg, L.M., K.E. Duncan, and J.M. Suflita, Bioenegy production via microbial conversion of residual oil to natural gas. Appl Environ Micro, 2008. 74(10): p. 3022-3029. 2. Jones, D.M., et al., Crude-oil biodegradation via

Research on the porous flow of the mechanism of viscous-elastic fluids displacing residual oil droplets in micro pores

Science.gov (United States)

Dong, Guanyu

2018-03-01

In order to analyze the microscopic stress field acting on residual oil droplets in micro pores, calculate its deformation, and explore the hydrodynamic mechanism of viscous-elastic fluids displacing oil droplets, the viscous-elastic fluid flow equations in micro pores are established by choosing the Upper Convected Maxwell constitutive equation; the numerical solutions of the flow field are obtained by volume control and Alternate Direction Implicit methods. From the above, the velocity field and microscopic stress field; the forces acting on residual oil droplets; the deformations of residual oil droplets by various viscous-elastic displacing fluids and at various Wiesenberg numbers are calculated and analyzed. The result demonstrated that both the normal stress and horizontal force acting on the residual oil droplets by viscous-elastic fluids are much larger compared to that of inelastic fluid; the distribution of normal stress changes abruptly; under the condition of the same pressure gradient in the system under investigation, the ratio of the horizontal forces acting on the residual oil droplets by different displacing fluids is about 1:8:20, which means that under the above conditions, the driving force on a oil droplet is 20 times higher for a viscous-elastic fluid compared to that of a Newtonian Fluid. The conclusions are supportive of the mechanism that viscous-elastic driving fluids can increase the Displacement Efficiency. This should be of help in designing new chemicals and selecting Enhanced Oil Recovery systems.

Improvement of Dune Sands by Residual Oil in Order to Use in Construction of Lagoons

Directory of Open Access Journals (Sweden)

Alborz Hajian nia

2011-10-01

Full Text Available This research which is based on experimental work, devoted to study the improvement and stabilization of dune sands in order to create strong layer and stabilize slope and floor construction of sewage Lagoons. Materials used stabilizing these soils are residual oil from the refinery. To confirm the effectiveness of the use of residual oil to improve the mechanical properties of the sand, various samples with different percentages were tested. In besides, the geotechnical and environmental tests were done. Results demonstrate that samples made with 5% oil have highest shear and unconfined compaction strength. It revealed that in compare with natural samples, cohesion and loading capacity highly increased and permeability decrease well. Percentage of fine aggregate, minerals and durability of oil in soil material were also investigated. Finally, effects of sewage on the samples were analyzed, and performance the oils were evaluated in order to use in lagoons.

Radioactivity concentration and heavy metal content in fuel oil and oil-ashes in Venezuela

International Nuclear Information System (INIS)

Barros, H.; Sajo-Bohus, L.; Abril, J.M.; Greaves, E.D.

2004-01-01

During the last years an intensive national program was developed to determine the environmental radioactivity levels in Venezuela. Gamma dose and the radon concentrations indoors, in drinking water, in caves and in artificial cavities including the effect of radon transported to the surface with the earth gas have been studied. To continue this project the oil and other natural energy resource should be considered. It is expected that the environmental radiation level is modified in regions where the oil industrial activity is more aggressive such as in the Zulia State and the Faja Petrolifera del Orinoco, (Central Region). In these regions Venezuela is producing 1.750 thousand barrels of oil from the near-to-the- surface or deep oil drilling. Petroleum constitutes an important source of energy and as the majority of natural source contains radionuclides and their disintegration products, being U, Ra, Pb, Bi, Po and K the most often encountered. The combustion of petroleum concentrate in the ashes those radioelements, and later enter the environment by different ways producing adverse effects on the quality of man life. The concentration of radioelements varies greatly between oil fields, then we still requiring local survey studies in this area. Moreover due to the recent national interest in recycling processes, it becomes important to take precaution in the selection of materials that may contain by-products of industrial origin, including oil. In fact the oil ashes, oil slurry and other mining by-products are thought to be employable in the building industry. The concentration of radioactivity in the ash from thermoelectric power plants that use petroleum as a primary energy source was determined. The analysis include the two major thermoelectric power plants in Venezuela, Ricardo Zuluaga on the northern sea side of Caracas and Planta Centro on the littoral of Carabobo State. The study cover different samples: fuel oil No 6, ashes, heavy and medium petroleum

Carbaryl and monocrotophos residues in cottonseed products. Part of a coordinated programme on isotopic tracer-aided studies of chemical residues in cotton seed, feed, oil and related products

International Nuclear Information System (INIS)

Pablo, F.E.

1981-03-01

Cotton plants of Deltapine variety were treated with carbaryl (naphthyl-1- 14 C), (6.7 mg/plant) three times at two week intervals. Seeds were collected at maturity and 14 C-residues were determined in the oil and cake by standard procedures. 14 C-carbaryl and/or metabolite residues were 0.42 and 0.15 mg/kg in the crude oil and cake respectively. Parallel studies were conducted with spectrophotometric techniques using p-nitrobenzene diazonium fluoborate as chromogenic agent. Applications were made three times at a rate of 14 mg/plant. Residues in the crude oil and cake were found to be 0.83 and 0.04 mg/kg respectively. The higher residue level in the oil - compared to the radiometric technique - probably relates to higher application rates. Cotton plants of Deltapine variety were treated with (N-methyl- 14 C) monocrotophos (0.09 mg/plant) three times at two week intervals, as recommended for agricultural practice. Seeds were collected at maturity and standard procedures for extraction, clean-up and paper and thin-layer chromatography were adopted for the ultimate determination of residues in seed, oil and cake. Parallel experiments, using spectrophotometric techniques, were made for comparison. 14 C-residues of monocrotophos and/or metabolites in cottonseed, crude oil and cake were found to be 0.06, 0.12 and 0.05 mg/kg respectively. Corresponding data obtained by non-nuclear techniques were 0.18, 0.42 and 0.15 mg/kg respectively. The discrepancy between the two sets of results may be related to different rates of application: 0.3 mg and 0.09 mg/plant for non-nuclear and radiometric techniques respectively. Among the major metabolites identified in the cottonseed were dimethyl phosphate and O-desmethyl monocrotophos. N-demethylated monocrotophos and sugar conjugates were also identified

Effect of inorganic chelate of zinc and restaurant residual oil added ...

African Journals Online (AJOL)

Jane

2011-08-01

Aug 1, 2011 ... residual oil added to feed mixture on the biochemical traits of thigh muscles in .... The basal diet (Soybean + corn); T2 = basal diet + 0% RRO + 50 mg/kg ZnO; T3 = basal ... fatty acids, using gas chromatography (AOAC, 1999).

Integrated project: Microbiological and physiological studies on the presence of residual concentrations in mineral-oil-contaminated soils after rehabilitation. Final report. Pt. 2; Mikrobiologische und physiologische Untersuchungen zur Frage der Restkonzentration bei der Sanierung mineraloelkontaminierter Boeden. Abschlussbericht. T. 2

Energy Technology Data Exchange (ETDEWEB)

Miethe, D.; Riis, V.; Stimming, M.

1996-01-04

It has been known for a long time that microorganisms are able to utilise mineral oils. Today various methods are practised which exploit autochthonous microorganisms` ability to utilise mineral oils. The main problem of microbial decomposition of hydrocarbons is that mineral oil residues remain. The aim of the present research project was therefore to determine the limits of the metabolisability of the substrate and find out why residues remain. Mineral oils and residual fractions differ markedly in their decomposability. Intermediate distillates are easily decomposed to a degree of 95-97% by well-adapted consorts. For high-boiling mineral oils (bp>400 C) the degree of decomposition is approx. 60%. Extracts from contaminated sites range from 40 to 60% in their degree of decomposability. The incomplete microbial decomposition of mineral oils is mainly due to their structure. There remain chemically and thermally extremely, inert hydrocarbons (mainly aliphatic and aromatic fused-ring systems) which are either hardly metabolisable or not at all. An important factor in soils or at other contaminated sites is that some of the substrate is not available because it is bound to the matrix thus increasing the proportion of residue. The next task after examining and presenting the causes of incomplete decomposition is to minimise residual mineral oil concentrations remaining after microbial decomposition. Here the use of special surfactants or of auxiliary substrates could point a way. Project applications to this end have already been submitted to the Federal Ministry for Education and Research. (orig.) [Deutsch] Dass Mikroorganismen in der Lage sind, Mineraloele zu verwerten, ist seit langem bekannt. Verfahren, die das Potential autochthoner Mikroorganismen zur Verwertung von Mineraloelen nutzen sind Praxis. Hauptproblem beim mikrobiellen Abbau der Kohlenwasserstoffe ist das Verbleiben von Mineraloelresten. Das Ziel des Forschungsvorhabens war die Ermittlung der Grenzen

Heating oil, distillates and residuals outlook

International Nuclear Information System (INIS)

Ervin, M.J.

2004-01-01

M.J. Ervin and Associates offers strategic planning support to the downstream petroleum industry in terms of price market monitoring, market analysis, media commentary and benchmarking of marketing operations. This presentation included graphs depicting supply and demand for heating oil distillates and residuals from the mid 1990s to 2004. It was noted that the long-term decline in residuals demand in the United States and Canada are due to environmental issues, the use of natural gas as an alternative, and the increasing complexity of refineries. Graphs depicting market impacts of refinery utilization and inventory trends showed that middle distillate production will increase at the expense of gasoline production. Middle distillates and gasoline markets will be more sensitive to supply disruptions, resulting in more frequent price spikes. Inventory trends indicate a greater reliance on product imports. The demand for heating fuel has stabilized due to the continued penetration of natural gas in eastern states and provinces. The demand for diesel fuel has growth 1.5 to 2 per cent while the demand for jet fuel has remained relatively flat and depends greatly on the growth of the gross national product (GNP). tabs., figs

Removal of emulsified oil in residual waters by means of dissolved air flotation

International Nuclear Information System (INIS)

Echeverri Londono, Carlos Alberto

1996-01-01

In this article is consigned a theoretical and experimental study on the treatment of industrial residual waters with emulsified oil, through the flotation process for dissolved air (FAD), changing some operation parameters and some importance topics, related with the process. The experimental results and the theoretical pattern, show that the removal of oil depends fundamentally on the chemical pretreatment. Efficiencies of removal of oil up of 99% they were obtained, using the dissolved air flotation with the help of coagulants

Processing and display of nuclear magnetism logging signals: application to residual oil determination

International Nuclear Information System (INIS)

Brown, R.J.S.; Neuman, C.H.

1980-01-01

A presentation is made of a series of computations and signal displays which help to show the nature of NML signals in general as well as to show the response to particular formation, hole, and tool conditions. Such processing of digitally recorded signals enables improved accuracy and bed resolution over that presented with the raw log. The treatment of drilling mud filtrate to eliminate NML signal from the brine phase in the invaded zone is described. Logs are shown as recorded before and after invasion of treated mud filtrate. This treatment causes the NML signal to correspond to residual oil only, enabling accurate and relatively inexpensive measurement of residual oil. 24 refs

Effect of inorganic chelate of zinc and restaurant residual oil added ...

African Journals Online (AJOL)

Effect of inorganic chelate of zinc and restaurant residual oil added to feed mixture ... The interaction effects of RRO and ZnO did not result to a significant change in ... Therefore, the effects of RRO deteriorated the quality of meat by raising the ...

Concentration measurements of biodiesel in engine oil and in diesel fuel

International Nuclear Information System (INIS)

Mäder, A; Eskiner, M; Burger, C; Rossner, M; Krahl, J; Ruck, W

2012-01-01

This work comprised a method for concentration measurements of biodiesel in engine oil as well as biodiesel in diesel fuel by a measurement of the permittivity of the mixture at a frequency range from 100 Hz to 20 kHz. For this purpose a special designed measurement cell with high sensitivity was designed. The results for the concentration measurements of biodiesel in the engine oil and diesel fuel shows linearity to the measurement cell signal for the concentration of biodiesel in the engine oil between 0.5% Vol. to 10% Vol. and for biodiesel in the diesel fuel between 0% Vol. to 100% Vol. The method to measure the concentration of biodiesel in the engine oil or the concentration of biodiesel in the diesel fuel is very accurate and low concentration of about 0.5% Vol. biodiesel in engine oil or in diesel fuel can be measured with high accuracy.

Iron utilization and liver mineral concentrations in rats fed safflower oil, flaxseed oil, olive oil, or beef tallow in combination with different concentrations of dietary iron.

Science.gov (United States)

Shotton, Andrea D; Droke, Elizabeth A

2004-03-01

Diets with a higher proportion of polyunsaturated fatty acids (i.e., linoleic acid) have decreased iron absorption and utilization compared with diets containing a higher proportion of the saturated fatty acid stearic acid (e.g., beef tallow). However, less is known regarding the influence of other polyunsaturated or monounsaturated fatty acids, along with higher dietary iron, on iron absorption and utilization. The present study was conducted to compare the effects of dietary fat sources known to vary in (n-3), (n-6), and (n-9) fatty acids on iron utilization and liver mineral concentrations. Male weanling rats were fed a diet containing 10, 35, or 100 microg/g iron in combination with safflower oil, flaxseed oil, olive oil, or beef tallow for 8 wk. Indicators of iron status, iron utilization, and liver iron concentrations were unaffected by an interaction between the fat source and iron concentration. Plasma copper was the only variable affected by an interaction between the fat source and dietary iron. Findings of this study demonstrate that flaxseed oil and olive oil may alter tissue minerals and affect iron utilization. Further studies should be conducted to establish the effect of varying (n-3), (n-6), and (n-9) fatty acids on trace mineral status and iron utilization.

Influence of lubricant oil residual fraction on recycled high density polyethylene properties and plastic packaging reverse logistics proposal

Directory of Open Access Journals (Sweden)

Harley Moraes Martins

2015-10-01

Full Text Available Abstract To recycle post-consumer HDPE contaminated with waste lubricating oils, companies include prior washing and drying in the process. This consumes large amounts of water and energy, generates significant effluent requiring treatment. This study assesses lubricating oil influence on HDPE properties to evaluate the feasibility of its direct mechanical recycling without washing. The current lubricating oil packaging reverse logistics in Rio de Janeiro municipality is also analyzed. HDPE bottle samples were processed with seven oil contents ranging from 1.6-29.4 (wt%. The results indicated the possibility to reprocess the polymer with oily residue not exceeding 3.2%. At higher levels, the external oil lubricating action affects the plastic matrix processing in the extruder and injection, and the recycled material has a burnt oil odor and free oil on the surface. Small residual oil amounts retain the plastic properties comparable to the washed recycled polymer and exhibited benefits associated with the oil plasticizer action. However, oil presence above 7.7% significantly changes the properties and reduces the elasticity and flexural modulus and the plastic matrix crystallinity.

Experimental investigation of wettability alteration on residual oil saturation using nonionic surfactants: Capillary pressure measurement

Directory of Open Access Journals (Sweden)

Masoud Amirpour

2015-12-01

Full Text Available Introducing the novel technique for enhancing oil recovery from available petroleum reservoirs is one of the important issues in future energy demands. Among of all operative factors, wettability may be the foremost parameter affecting residual oil saturation in all stage of oil recovery. Although wettability alteration is one of the methods which enhance oil recovery from the petroleum reservoir. Recently, the studies which focused on this subject were more than the past and many contributions have been made on this area. The main objective of the current study is experimentally investigation of the two nonionic surfactants effects on altering wettability of reservoir rocks. Purpose of this work is to change the wettability to preferentially the water-wet condition. Also reducing the residual oil saturation (Sor is the other purpose of this work. The wettability alteration of reservoir rock is measured by two main quantitative methods namely contact angle and the USBM methods. Results of this study showed that surfactant flooding is more effective in oil-wet rocks to change their wettability and consequently reducing Sor to a low value. Cedar (Zizyphus Spina Christi is low priced, absolutely natural, and abundantly accessible in the Middle East and Central Asia. Based on the results, this material can be used as a chemical surfactant in field for enhancing oil recovery.

Microbial enhanced oil recovery and compositions therefor

Science.gov (United States)

Bryant, Rebecca S.

1990-01-01

A method is provided for microbial enhanced oil recovery, wherein a combination of microorganisms is empirically formulated based on survivability under reservoir conditions and oil recovery efficiency, such that injection of the microbial combination may be made, in the presence of essentially only nutrient solution, directly into an injection well of an oil bearing reservoir having oil present at waterflood residual oil saturation concentration. The microbial combination is capable of displacing residual oil from reservoir rock, which oil may be recovered by waterflooding without causing plugging of the reservoir rock. Further, the microorganisms are capable of being transported through the pores of the reservoir rock between said injection well and associated production wells, during waterflooding, which results in a larger area of the reservoir being covered by the oil-mobilizing microorganisms.

Gasification of coal as efficient means of environment protection and hydrogenation of heavy oils residues

Energy Technology Data Exchange (ETDEWEB)

Krichko, A.A.; Maloletnev, A.S. [Fossil Fuel Institute, Moscow (Russian Federation)

1995-12-31

The Russia`s more then 50% of coals produced in its European part contain over 2,5% of sulphur, and the coals containing less than 1.5% of sulphurs comprise ca.20%. Thus, utilisation of the sulphide coals is inevitable, and there a problem arises concerning the technology of their sensible use and considering the requirements on the environment protection. Russia`s specialists have developed a design and construction for a steam-gas installation with a closed cycle gasification of the solid fuel. The gasification process will proceed in the fluidized bed under forced pressure of the steam-air blast. Characteristic features of this process are the following: a higher efficiency (the capacity of one gas generator is 3-3,5 times larger than that attained in the present gas generators of the Lurgy`s type): 2-2,5 times decreased fuel losses as compared to the Winkler`s generators; retention of the sensible heat, resulting in an increased total energy efficiency. The main task for petroleum refining industry at the present stage is the increase of depth of oil processing with the aim to intensify motor fuel production. One of the ways to solve the problem is to involve heavy oil residues into the processing. But the high metal and asphaltenes contents in the latter make the application of traditional methods and processes more difficult. Up to now there is no simple and effective technology which could give the opportunity to use oil residues for distillate fractions production. In Fossil fuel institute a process for hydrogenation of high boiling oil products, including with high sulphur, vanadium and nickel contents ones, into distillates and metals concentrates. The main point of the new process is as follows: the water solution of catalytic additive, for which purpose water soluble metal salts of VI-VIII groups are used, is mixed with tar, dispersed and then subjected to additional supercavitation in a special apparatus.

STUDY OF THE THERMAL CRACKING DURING THE VACUUM DISTILLATION OF ATMOSPHERIC RESIDUE OF CRUDE OIL

Directory of Open Access Journals (Sweden)

JAOUAD ELAYANE

2017-03-01

Full Text Available This article concerns the study of the thermal cracking as undesirable phenomenon in the vacuum distillation of atmospheric residue of crude oil. In this point, we have sought to identify and characterize the effect of the increase in the temperature of vacuum distillation on the separation and the modification of the constituents of atmospheric residue of crude oil whose origin is Arabian Light. This study has been carried out by several techniques of analysis such as the density (ASTM D4052, distillation (ASTM D1160, determination of heavy metals nickel and vanadium (IFP9422, dosing of Conradson Carbon (ASTM D189, dosing of asphaltenes (ASTM D2549 and dosage of PCI (polycyclic aromatics (ASTM D 5186. The results showed a clear idea on the decomposition of the atmospheric residue and their influence on the performance of the vacuum distillation unit.

Oil concentrations below a demulsifier treated slick

International Nuclear Information System (INIS)

Lunel, T.; Lewis, A.

1993-01-01

During field trials in the North Sea in 1992, three 20-tonne slicks of a relatively weak 30% water-in-oil emulsion were released. Two of the slicks were treated with demulsifier from spray aircraft and one of the treated slicks was sprayed with dispersant seven hours later. The experiment used flow-through fluorometry to determine oil concentrations below the control and demulsifier-treated slick. Remote sensing imagery was used to determine the area of the surface slicks. Emulsion formation was slowed down in the two demulsifier-treated slicks relative to the control slick. The demulsifier-treated slicks resulted in maximum oil concentrations in water some five times higher than the control slick and spread over a volume 10-20 times as large. The control slick was therefore more persistent on the sea surface than either of the treated slicks. 5 refs., 5 figs., 5 tabs

Microfluidic acoustophoretic force based low-concentration oil separation and detection from the environment.

Science.gov (United States)

Wang, Han; Liu, Zhongzheng; Kim, Sungman; Koo, Chiwan; Cho, Younghak; Jang, Dong-Young; Kim, Yong-Joe; Han, Arum

2014-03-07

Detecting and quantifying extremely low concentrations of oil from the environment have broad applications in oil spill monitoring in ocean and coastal areas as well as in oil leakage monitoring on land. Currently available methods for low-concentration oil detection are bulky or costly with limited sensitivities. Thus they are difficult to be used as portable and field-deployable detectors in the case of oil spills or for monitoring the long-term effects of dispersed oil on marine and coastal ecosystems. Here, we present a low-concentration oil droplet trapping and detection microfluidic system based on the acoustophoresis phenomenon where oil droplets in water having a negative acoustic contrast factor move towards acoustic pressure anti-nodes. By trapping oil droplets from water samples flowing through a microfluidic channel, even very low concentrations of oil droplets can be concentrated to a detectable level for further analyses, which is a significant improvement over currently available oil detection systems. Oil droplets in water were successfully trapped and accumulated in a circular acoustophoretic trapping chamber of the microfluidic device and detected using a custom-built compact fluorescent detector based on the natural fluorescence of the trapped crude oil droplets. After the on-line detection, crude oil droplets released from the trapping chamber were successfully separated into a collection outlet by acoustophoretic force for further off-chip analyses. The developed microfluidic system provides a new way of trapping, detecting, and separating low-concentration crude oil from environmental water samples and holds promise as a low-cost field-deployable oil detector with extremely high sensitivity. The microfluidic system and operation principle are expected to be utilized in a wide range of applications where separating, concentrating, and detecting small particles having a negative acoustic contrast factor are required.

Production of vanillin from waste residue of rice bran oil by Aspergillus niger and Pycnoporus cinnabarinus.

Science.gov (United States)

Zheng, Lirong; Zheng, Pu; Sun, Zhihao; Bai, Yanbing; Wang, Jun; Guo, Xinfu

2007-03-01

A new technology of transforming ferulic acid, which was from waste residue of rice bran oil, into vanillin was developed by a combination of fungal strains Aspergillus niger CGMCC0774 and Pycnoporus cinnabarinus CGMCC1115. Various concentrations of ferulic acid were compared, and the highest yield reached 2.2 g l(-1) of vanillic acid by A. niger CGMCC0774 in a 25 l fermenter when concentration of ferulic acid was 4 g l(-1). The filtrate of A. niger CGMCC0774 culture was concentrated and vanillic acid in the filtrate was bio-converted into vanillin by P. cinnabarinus CGMCC1115. The yield of vanillin reached 2.8 g l(-1) when 5 g l(-1) of glucose and 25 g of HZ802 resin were supplemented in the bioconversion medium. The 13C isotope analysis indicated that delta13C(PDB) of vanillin prepared was much different from chemically synthesized vanillin.

Effects of storage and processing on residue levels of chlorpyrifos in soybeans.

Science.gov (United States)

Zhao, Liuwei; Ge, Jing; Liu, Fengmao; Jiang, Naiwen

2014-05-01

The residue levels of chlorpyrifos in soybeans during storage and processing were investigated. Soybeans were treated with chlorpyrifos aqueous solution and placed in a sealed plastic container. The residue of chlorpyrifos was determined in soybeans at six time points within 0 and 112days during storage and oil processing of the soybeans was conducted. The analysis of the residues of chlorpyrifos was carried out by gas chromatography-mass spectrometry (GC-MS). Results show that the dissipation of chlorpyrifos in soybeans is about 62% during the storage period. Moreover, the carryover of the residues from soybeans into oil is found to be related to the processing methods. Processing factor, which is defined as the ratio of chlorpyrifos residue concentration in oil sample to that in the soybean samples, was 11 and 0.25 after cold and hot pressing, respectively. Copyright © 2013 Elsevier Ltd. All rights reserved.

Time course of pulmonary burden in mice exposed to residual oil fly ash

OpenAIRE

Giovanna Marcella Cavalcante Carvalho; Lilian Katie Nagato; Sheila da Silva Fagundes; Flavia Brandão dos Santos; Andrea Surrage Calheiros; Olaf eMalm; Patricia Torres Bozza; Paulo Hilario Nascimento Saldiva; Debora Souza Faffe; Patricia Rieken Macedo Rocco; Walter Araujo Zin

2014-01-01

Residual oil fly ash (ROFA) is a common pollutant in areas where oil is burned. This particulate matter (PM) with a broad distribution of particle diameters can be inhaled by human beings and putatively damage their respiratory system. Although some studies deal with cultured cells, animals, and even epidemiological issues, so far a comprehensive analysis of respiratory outcomes as a function of the time elapsed after exposure to a low dose of ROFA is wanted. Thus, we aimed to investigate the...

Genetic control of soybean seed oil: I. QTL and genes associated with seed oil concentration in RIL populations derived from crossing moderately high-oil parents.

Science.gov (United States)

Eskandari, Mehrzad; Cober, Elroy R; Rajcan, Istvan

2013-02-01

Soybean seed is a major source of oil for human consumption worldwide and the main renewable feedstock for biodiesel production in North America. Increasing seed oil concentration in soybean [Glycine max (L.) Merrill] with no or minimal impact on protein concentration could be accelerated by exploiting quantitative trait loci (QTL) or gene-specific markers. Oil concentration in soybean is a polygenic trait regulated by many genes with mostly small effects and which is negatively associated with protein concentration. The objectives of this study were to discover and validate oil QTL in two recombinant inbred line (RIL) populations derived from crosses between three moderately high-oil soybean cultivars, OAC Wallace, OAC Glencoe, and RCAT Angora. The RIL populations were grown across several environments over 2 years in Ontario, Canada. In a population of 203 F(3:6) RILs from a cross of OAC Wallace and OAC Glencoe, a total of 11 genomic regions on nine different chromosomes were identified as associated with oil concentration using multiple QTL mapping and single-factor ANOVA. The percentage of the phenotypic variation accounted for by each QTL ranged from 4 to 11 %. Of the five QTL that were tested in a population of 211 F(3:5) RILs from the cross RCAT Angora × OAC Wallace, a "trait-based" bidirectional selective genotyping analysis validated four QTL (80 %). In addition, a total of seven two-way epistatic interactions were identified for oil concentration in this study. The QTL and epistatic interactions identified in this study could be used in marker-assisted introgression aimed at pyramiding high-oil alleles in soybean cultivars to increase oil concentration for biodiesel as well as edible oil applications.

Aqueous Rare Earth Element Patterns and Concentration in Thermal Brines Associated With Oil and Gas Production

Energy Technology Data Exchange (ETDEWEB)

Nye, Charles [University of Wyoming; Quillinan, Scott Austin [University of Wyoming; Neupane, Ghanashyam [Idaho National Lab. (INL), Idaho Falls, ID (United States); McLing, Travis [Idaho National Lab. (INL), Idaho Falls, ID (United States)

2017-02-13

This study is part of a joint effort by the University of Wyoming (UW) School of Energy Resources (SER), the UW Engineering Department, Idaho National Laboratories (INL), and the United States Geological Survey (USGS) to describe rare earth element concentrations in oil and gas produced waters and in coal-fired power station ash ponds. In this work we present rare earth element (REE) and trace metal behavior in produced water from four Wyoming oil and gas fields and surface ash pond water from two coal-fired power stations. The concentration of REEs in oil and gas produced waters is largely unknown. For example, of the 150,000 entries in the USGS National Produced Waters Geochemical Database less than 5 include data for REEs. Part of the reason for this scarcity is the analytical challenge of measuring REEs in high salinity, hydrocarbon-bearing waters. The industry standard for water analysis struggles to detect REEs in natural waters under ideal conditions. The detection of REEs in oil and gas field samples becomes all but impossible with the background noise and interferences caused by high concentrations of non-REE ions and residual hydrocarbons. The INL team members have overcome many of these challenges (e.g. McLing, 2014), and continue to develop their methods. Using the methods of the INL team members we measured REEs in high salinity oil and gas produced waters. Our results show that REEs exist as a dissolved species in all waters measured for this project, typically within the parts per trillion range. The samples may be grouped into two broad categories analytically, and these categories match their genesis: Wyoming oil and gas brines contain elevated levels of Europium, and Wyoming industrial pond waters show elevation in heavy REEs (HREEs). While broadly true, important variations exist within both groups. In the same field Europium can vary by more than an order of magnitude, and likewise HREEs in industrial ponds at the same site can vary by more than

Decarboxylation Of Palm And Groundnut Oils In Medium Uv ...

African Journals Online (AJOL)

denise

INTRODUCTION. Vegetable oils undergo appreciable deterioration during processing and storage. The residual free fatty acid (FFA) concentration of vegetable oils is a function of the processing and storage conditions. Vegetable oils spoilage, usually defined as rancidity, is the result of fatty acid moity has been recognized ...

[Pretreatment of oil palm residues by dilute alkali for cellulosic ethanol production].

Science.gov (United States)

Zhang, Haiyan; Zhou, Yujie; Li, Jinping; Dai, Lingmei; Liu, Dehua; Zhang, Jian'an; Choo, Yuen May; Loh, Soh Kheang

2013-04-01

In the study, we used oil palm residues (empty fruit bunch, EFB) as raw material to produce cellulosic ethanol by pretreatment, enzymatic hydrolysis and fermentation. Firstly, the pretreatment of EFB with alkali, alkali/hydrogen peroxide and the effects on the components and enzymatic hydrolysis of cellulose were studied. The results show that dilute alkali was the suitable pretreatment method and the conditions were first to soak the substrate with 1% sodium hydroxide with a solid-liquid ratio of 1:10 at 40 degrees C for 24 h, and then subjected to 121 degrees C for 30 min. Under the conditions, EFB solid recovery was 74.09%, and glucan, xylan and lignin content were 44.08%, 25.74% and 13.89%, respectively. After separated with alkali solution, the pretreated EFB was washed and hydrolyzed for 72 h with 5% substrate concentration and 30 FPU/g dry mass (DM) enzyme loading, and the conversion of glucan and xylan reached 84.44% and 89.28%, respectively. We further investigated the effects of substrate concentration and enzyme loading on enzymatic hydrolysis and ethanol batch simultaneous saccharification and fermentation (SSF). The results show that when enzyme loading was 30 FPU/g DM and substrate concentration was increased from 5% to 25%, ethanol concentration were 9.76 g/L and 35.25 g/L after 72 h fermentation with Saccharomyces cerevisiae (inoculum size 5%, V/V), which was 79.09% and 56.96% of ethanol theory yield.

Residual biomass potential in olive tree cultivation and olive oil industry in Spain: valorization proposal in a biorefinery contex

Energy Technology Data Exchange (ETDEWEB)

Manzanares, P.; Ruiz, E.; Ballesteros, M.; Negro, M.J.; Gallego, F.J.; López-Linares, J.C.; Castro, E.

2017-07-01

Olive crop and olive oil industry generates several residues, i.e., olive tree pruning biomass (OTPB), extracted olive pomace (EOP) and olive leaves (OL) that could be used to produce high-added value products in an integrated biorefinery. OTPB is generated in the field as a result of pruning operation to remove old branches; EOP is the main residue of the pomace olive oil extracting industry after extraction with hexane of residual oil contained in olive pomace; and OL comes from the olive cleaning process carried out at olive mills, where small branches and leaves are separated by density. In this work, an analysis of the potential of OTPB, EOP and OL residues was addressed by estimating the production volumes at national level and the spatial distribution of these residues using geographic information system software. Information provided by public institutions and personal surveys to the industries was evaluated. Moreover, chemical analysis of the residues was undertaken and the results used to make a first assessment of valorization into biofuels such as bioethanol and bio based chemicals. Results show that close to 4.2 million tons/year of EOP, OL and OTPB derived from olive oil industry and olive tree cultivation in Spain could be available as a raw material for biorefineries in Spain. The analysis of the chemical characteristics indicates the relevant potential of these feedstocks for the production of bioethanol and other compounds such as phenols based on suitable processing and conversion routes, although techno-economic evaluations must be tackled to refine this approach.

Residual biomass potential in olive tree cultivation and olive oil industry in Spain: valorization proposal in a biorefinery context

Directory of Open Access Journals (Sweden)

Paloma Manzanares

2017-12-01

Full Text Available Olive crop and olive oil industry generates several residues, i.e., olive tree pruning biomass (OTPB, extracted olive pomace (EOP and olive leaves (OL that could be used to produce high-added value products in an integrated biorefinery. OTPB is generated in the field as a result of pruning operation to remove old branches; EOP is the main residue of the pomace olive oil extracting industry after extraction with hexane of residual oil contained in olive pomace; and OL comes from the olive cleaning process carried out at olive mills, where small branches and leaves are separated by density. In this work, an analysis of the potential of OTPB, EOP and OL residues was addressed by estimating the production volumes at national level and the spatial distribution of these residues using geographic information system software. Information provided by public institutions and personal surveys to the industries was evaluated. Moreover, chemical analysis of the residues was undertaken and the results used to make a first assessment of valorization into biofuels such as bioethanol and bio based chemicals. Results show that close to 4.2 million tons/year of EOP, OL and OTPB derived from olive oil industry and olive tree cultivation in Spain could be available as a raw material for biorefineries in Spain. The analysis of the chemical characteristics indicates the relevant potential of these feedstocks for the production of bioethanol and other compounds such as phenols based on suitable processing and conversion routes, although techno-economic evaluations must be tackled to refine this approach.

Determination of residual oil saturation from time-lapse pulsed neutron capture logs in a large sandstone reservoir

International Nuclear Information System (INIS)

Syed, E.V.; Salaita, G.N.; McCaffery, F.G.

1991-01-01

Cased hole logging with pulsed neutron tools finds extensive use for identifying zones of water breakthrough and monitoring oil-water contacts in oil reservoirs being depleted by waterflooding or natural water drive. Results of such surveys then find direct use for planning recompletions and water shutoff treatments. Pulsed neutron capture (PNC) logs are useful for estimating water saturation changes behind casing in the presence of a constant, high-salinity environment. PNC log surveys run at different times, i.e., in a time-lapse mode, are particularly amenable to quantitative analysis. The combined use of the original open hole and PNC time-lapse log information can then provide information on remaining or residual oil saturations in a reservoir. This paper reports analyses of historical pulsed neutron capture log data to assess residual oil saturation in naturally water-swept zones for selected wells from a large sandstone reservoir in the Middle East. Quantitative determination of oil saturations was aided by PNC log information obtained from a series of tests conducted in a new well in the same field

Effects of dressing and cooking on DDT concentrations in certain fish from Lake Michigan

Science.gov (United States)

Reinert, Robert E.; Stewart, Donald; Seagran, Harry L.

1972-01-01

Concentrations of DDT residues were highest in parts of the body with the highest oil content in four species of fish from Lake Michigan: yellow perch (Perca flavescens), bloater (Coregonus hoyi), lake trout (Salvelinus namaycush), and coho salmon (Oncorhynchus kisutch). Dressing reduced the DDT residues and oil content by more than 90% in yellow perch but had little effect in the other three species. The concentration of DDT residues in bloaters was changed little by smoking but was reduced 64–72% by other methods of cooking: from 8.0 ppm (raw) to 2.2 ppm after frying in corn oil; from 10.7 to 3.9 ppm after frying in lard; and from 9.1 to 3.2 ppm after broiling. The concentration of DDT residues in fillets of yellow perch changed only from 0.3 ppm (raw) to 0.4 or 0.5 ppm after baking, frying, or broiling.

Extra heavy oil and refinery residues upgrading through Eni Slurry Technology : first EST commercial unit

Energy Technology Data Exchange (ETDEWEB)

Rispoli, G.; Sanfilippo, D.; Amoroso, A [Eni S.p.A., Rome (Italy)

2009-07-01

The production of heavy crude oils is projected to continue to grow in the upstream oil industry given that large reserves of unconventional extra heavy crude and bitumen exist in several geographic areas including Canada and Venezuela. As reserves of conventional crude oil continue to decline, these unconventional feedstocks are becoming an opportunity to pursue, but they require effective technologies for upgrading and meeting the growing demand for light and middle distillate fuels. This paper described the proprietary technology that offers a solution to upstream and downstream oil producers for bottom-of-the-barrel upgrading. En i Slurry Technology (EST) is constructing an industrial plant in its Sannazzaro refinery in Italy. The plant is designed to convert 23,000 BPSD of vacuum residue into high quality diesel and other valuable refinery streams such as liquefied petroleum gas, naphtha and jet fuel. EST is an H-addition process characterized by the use of a special homogeneous isothermal intrinsically safe reactor, and of a nano-dispersed non-ageing catalyst. EST converts more than 98 per cent of any type of residues to about 110 per cent volume of light products and distillates or extra heavy oils to high quality bottomless SCO. In typical performance, HDS is greater than 85 per cent, HDM greater than 99 per cent and HDCCR greater than 97 per cent. EST also achieves the target of zero fuel oil - zero coke. 12 refs., 4 tabs., 5 figs.

A fundamental research for upgrading heavy oil using syngas as hydrogen source

Energy Technology Data Exchange (ETDEWEB)

Yan, D.; Yuan, M.; Sun, X.; Zhao, S. [China Univ. of Petroleum, Beijing (China). State Key Laboratory of Heavy Oil Processing

2006-07-01

The stock of heavy oil and residue from petroleum fractions has become more important as a component in supplying demands for fuel and petrochemical feeds. Finding economical means of upgrading heavy oils is extremely important in order to ensure future fuel supply. A number of new technologies for upgrading heavy oils have been evaluated, including residual fluid catalytic cracking (RFCC), hydrogenation, thermal conversion, and solvent deasphalting. However, the commercial application of such technologies is mainly constrained by the metal and residual carbon concentrations that are present in all heavy oils. Conventional technologies used to upgrade vacuum residue (VR) result in heavy coke formation, with a consequential reduction in the life of expensive, high-performance catalysts. The hydro upgrading process can significantly remove the concentration of heteroatom such as sulfur, nitrogen, and metals in the liquid products. This paper investigated upgrading of heavy oil using syngas as an alternative hydrogen source with a dispersed catalyst. The paper discussed the experiment with reference to the feedstock and catalyst precursors; finely dispersed catalysts preparation; experimental apparatus; experimental design and procedure; and analysis. The results were presented in terms of effects of catalyst dispersion; effect of hydro-upgrading heavy oil using syngas as alternative source; and effects of different catalysts on residue hydrocracking. Last, the paper discussed the properties of the hydrocracked oil treated with syngas. The study confirmed the effectiveness of the slurry bed hydrocracking catalyst using syngas as a hydrogen source. 23 refs., 8 tabs., 16 figs.

Genetic control of soybean seed oil: II. QTL and genes that increase oil concentration without decreasing protein or with increased seed yield.

Science.gov (United States)

Eskandari, Mehrzad; Cober, Elroy R; Rajcan, Istvan

2013-06-01

Soybean [Glycine max (L.) Merrill] seed oil is the primary global source of edible oil and a major renewable and sustainable feedstock for biodiesel production. Therefore, increasing the relative oil concentration in soybean is desirable; however, that goal is complex due to the quantitative nature of the oil concentration trait and possible effects on major agronomic traits such as seed yield or protein concentration. The objectives of the present study were to study the relationship between seed oil concentration and important agronomic and seed quality traits, including seed yield, 100-seed weight, protein concentration, plant height, and days to maturity, and to identify oil quantitative trait loci (QTL) that are co-localized with the traits evaluated. A population of 203 F4:6 recombinant inbred lines, derived from a cross between moderately high oil soybean genotypes OAC Wallace and OAC Glencoe, was developed and grown across multiple environments in Ontario, Canada, in 2009 and 2010. Among the 11 QTL associated with seed oil concentration in the population, which were detected using either single-factor ANOVA or multiple QTL mapping methods, the number of QTL that were co-localized with other important traits QTL were six for protein concentration, four for seed yield, two for 100-seed weight, one for days to maturity, and one for plant height. The oil-beneficial allele of the QTL tagged by marker Sat_020 was positively associated with seed protein concentration. The oil favorable alleles of markers Satt001 and GmDGAT2B were positively correlated with seed yield. In addition, significant two-way epistatic interactions, where one of the interacting markers was solely associated with seed oil concentration, were identified for the selected traits in this study. The number of significant epistatic interactions was seven for yield, four for days to maturity, two for 100-seed weight, one for protein concentration, and one for plant height. The identified molecular

Prediction of ambient concentration of volatile organic compounds (VOCs) from the Sea Empress oil spill using vapour and oil property models

International Nuclear Information System (INIS)

Carruthers, D.J.; Ellis, K.L.

1997-09-01

Modelling has been used to estimate concentrations of benzene, toluene, ethyl benzene and xylene (BTEX), 1,3 butadiene and total hydrocarbons due to evaporation of volatiles from the Sea Empress oil spill. This involved estimating the release rates of oil during each tidal cycle, calculating the spread and evaporation rate of the oil and then using the dispersion model ADMS to determine concentrations in air of the species. The calculations generally show that the highest concentrations occur directly above recently released oil (released within the last 12 hours). Concentrations on land were generally small as the predominant wind directions were seaward throughout the period when the oil spill would have been evaporating. However, total hydrocarbon concentrations measured at various land sites were significant during the spill period even when the wind was blowing away from the monitoring sites. The measured concentrations were also high for a further period after the spill when evaporation of the spilled oil would have decreased to small levels. This suggests that much of the measured hydrocarbons were emitted from other sources (e.g. the oil refineries). (author)

Determination of macro nickel, vanadium and iron in crude oil and residues by derivative spectrophotometry

International Nuclear Information System (INIS)

Liu, W.; Wang, L.; Li, X.

1992-01-01

In this paper, a new method with derivative spectrophotometry and 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol as the chromogenic reagent in buffer solution of different pH developed for determining micro amounts of nickel. Vanadium and iron in crude oil and residues is reported. Forth-, Second- and Third-, Fourth-order derivative spectrophotometry were applied to determine nickel, nickel and vanadium, nickel and iron in crude oil and residues, respectively. The derivative maximums chosen for the measurement were at 556 nm for nickel, 540 nm and 643 nm for nickel and vanadium, 524 nm and 604 nm for nickel and iron. Beer's law is valid for the range 1.0 x 10 -6 to 2.5 x 10 -5 M

Effect of Residue Nitrogen Concentration and Time Duration on Carbon Mineralization Rate of Alfalfa Residues in Regions with Different Climatic Conditions

Directory of Open Access Journals (Sweden)

saeid shafiei

2017-08-01

Full Text Available Introduction Various factors like climatic conditions, vegetation, soil properties, topography, time, plant residue quality and crop management strategies affect the decomposition rate of organic carbon (OC and its residence time in soil. Plant residue management concerns nutrients recycling, carbon recycling in ecosystems and the increasing CO2 concentration in the atmosphere. Plant residue decomposition is a fundamental process in recycling of organic matter and elements in most ecosystems. Soil management, particularly plant residue management, changes soil organic matter both qualitatively and quantitatively. Soil respiration and carbon loss are affected by soil temperature, soil moisture, air temperature, solar radiation and precipitation. In natural agro-ecosystems, residue contains different concentrations of nitrogen. It is important to understand the rate and processes involved in plant residue decomposition, as these residues continue to be added to the soil under different weather conditions, especially in arid and semi-arid climates. Material and methods Organic carbon mineralization of alfalfa residue with different nitrogen concentrations was assessed in different climatic conditions using split-plot experiments over time and the effects of climate was determined using composite analysis. The climatic conditions were classified as warm-arid (Jiroft, temperate arid (Narab and cold semi-arid (Sardouiyeh using cluster analysis and the nitrogen (N concentrations of alfalfa residue were low, medium and high. The alfalfa residue incubated for four different time periods (2, 4, 6 and 8 months. The dynamics of organic carbon in different regions measured using litter bags (20×10 cm containing 20 g alfalfa residue of 2-10 mm length which were placed on the soil surface. Results and discussion The results of this study showed that in a warm-arid (Jiroft, carbon loss and the carbon decomposition rate constant were low in a cold semi

Determination of potassium concentration in salt water for residual beta radioactivity measurements

International Nuclear Information System (INIS)

Suarez-Navarro, J.A.; Pujol, Ll.

2004-01-01

High interferences may arise in the determination of potassium concentration in salt water. Several analytical methods were studied to determine which method provided the most accurate measurements of potassium concentration. This study is relevant for radiation protection because the exact amount of potassium in water samples must be known for determinations of residual beta activity concentration. The fitting algorithm of the calibration curve and estimation of uncertainty in potassium determinations were also studied. The reproducibility of the proposed analytical method was tested by internal and external validation. Furthermore, the residual beta activity concentration of several Spanish seawater and brackish river water samples was determined using the proposed method

PHYSICOCHEMICAL CHARACTERISTICS, PESTICIDE RESIDUE AND AFLATOXIN CONTAMINATION OF COLD PRESSED PUMPKIN SEED (Cucurbita pepo L. OILS FROM CENTRAL ANATOLIA REGION OF TURKEY

Directory of Open Access Journals (Sweden)

FATMA NUR ARSLAN

2017-06-01

Full Text Available In this study, physicochemical characteristics, pesticide residues and aflatoxin contaminations of cold pressed pumpkin seed (Cucurbita pepo L. oils cultivated in four different central Anatolia regions of Turkey, were investigated. Lab-scale screw press machine was used to produce cold pressed pumpkin seed oils and the oil contents were found between 42.8%−47.4% for naked seeds. The physicochemical characteristic (refractive index, viscosity, color value, triglyceride profile analysis, peroxide value, iodine value, free fatty acid, saponification number, unsaponified matter, specific extinction values at 232 and 270 nm of cold pressed oils were determined by using different analytical techniques. The results showed that there was a non-significant difference between cold pressed pumpkin seed oils from different regions, in terms of physicochemical characteristics. The contents of pesticide residue and aflatoxin B1, B2, G1 and G2 contamination were determined by using validated UHPLC-MS/MS method. The chlorpyrifos pesticide residue was detected under the limit value declared by official authorities for the quality assessment of edible oils. Aflatoxins weren’t detected in any of studied pumpkin seed oils. Therefore, in food industry the positive effect of screw-pressing application could be useful for preservation of bioactive compounds during edible oil production and also enhancing of their functional properties.

Chemical durability of glass and glass-ceramic materials, developed in laboratory scale, from industrial oil shale residue. Preliminary results

International Nuclear Information System (INIS)

Araujo Fonseca, M.V. de; Souza Santos, P. de

1990-01-01

Industrial developments frequently drive to the natural resources extinction. The recycling era has come out a long time ago and it has been evident that great part of industrial work's problems are related to the pollution and the raw materials extinction. These problems should be solved, with advantages, through industrial residues recycling. This study deals with glass and glass-ceramics materials obtained from oil shale (Irati Formation-Sao Mateus do Sul-Parana State) industrialization residues. The reached results show that a controled devitrification of retorted oil shale glass improves its performance related to chemical attack. The crystallinity caracterization of the oil shales glass-ceramic was made through X-ray diffraction. (author) [pt

Stability of tetrachlorvinphos residues in faba beans and soya bean oil towards different processing procedures

International Nuclear Information System (INIS)

Zayed, S.M.A.D.; Farghaly, M.

1987-01-01

Cooking of contaminated faba beans did not degrade the originally present potentially toxic residues, namely, tetrachlorvinphos and its desmethyl derivative to any appreciable extent. Processing of contaminated soya bean oil, on the other hand, led to degradation of tetrachlorvinphos and its metabolites to give mono and dimethyl phosphates. Feeding of mice with bound residues of tetrachlorvinphos in beans for 90 days led to an apparent decrease in the rate of body weight gain. (author)

Antimicrobial Efficacy of Various Essential Oils at Varying Concentrations against Periopathogen Porphyromonas gingivalis

Science.gov (United States)

Grover, Harpreet Singh; Deswal, Himanshu; Agarwal, Preeti

2016-01-01

Introduction Porphyromonas gingivalis (P.gingivalis) is a notorious perio-pathogen with the ability to evade host defense mechanism and invade into the periodontal tissues. Many antimicrobial agents have been tested that curb its growth, although these agents tend to produce side effects such as antibiotic resistance and opportunistic infections. Therefore search for naturally occurring anti-microbials with lesser side effects is the need of the hour. Aim The aim of this study was to substantiate the antimicrobial activity of various essential oils; eucalyptus oil, chamomile oil, tea tree oil and turmeric oil against P. gingivalis. Materials and Methods Pure cultures of P. gingivalis were grown on selective blood agar. Antimicrobial efficacy of various concentrations of essential oils (0%, 25%, 50% and 100%) was assessed via disc diffusion test. Zone of inhibition were measured around disc after 48 hours in millimeters. Results Zones of inhibition were directly proportional to the concentration of essential oils tested. At 100% concentration all the tested oils possess antimicrobial activity against P.gingivalis with eucalyptus oil being most effective followed by tea tree oil, chamomile oil and turmeric oil. Conclusion All essential oils tested were effective against P.gingivalis. After testing for their clinical safety they could be developed into local agents to prevent and treat periodontitis. PMID:27790572

Aerobic microbial enhanced oil recovery

Energy Technology Data Exchange (ETDEWEB)

Torsvik, T. [Univ. of Bergen (Norway); Gilje, E.; Sunde, E.

1995-12-31

In aerobic MEOR, the ability of oil-degrading bacteria to mobilize oil is used to increase oil recovery. In this process, oxygen and mineral nutrients are injected into the oil reservoir in order to stimulate growth of aerobic oil-degrading bacteria in the reservoir. Experiments carried out in a model sandstone with stock tank oil and bacteria isolated from offshore wells showed that residual oil saturation was lowered from 27% to 3%. The process was time dependent, not pore volume dependent. During MEOR flooding, the relative permeability of water was lowered. Oxygen and active bacteria were needed for the process to take place. Maximum efficiency was reached at low oxygen concentrations, approximately 1 mg O{sub 2}/liter.

Essential oil extraction with concentrating solar thermal energy

OpenAIRE

Veynandt, François

2015-01-01

Material complementari del cas estudi "Essential oil extraction with concentrating solar thermal energy”, part component del llibre "Case studies for developing globally responsible engineers" Peer Reviewed

Geographic Concentration of Oil Infrastructure: Issues and Options

Science.gov (United States)

2007-03-24

along the Gulf of Mexico. 28 Figure 3 reveals the travel pattern of the two hurricanes and the scope of impact on oil and natural gas platforms...road to travel before this level of cooperation is achieved. 15 Consideration of this issue of geographic concentration of oil infrastructure...million), Port Security Grants ($201 million), Intercity Bus Security Grants ($12 million), Trucking Security Grants ($12 million), and Buffer Zone

Radiotracer studies of pesticide residues in edible oil seeds and related products

International Nuclear Information System (INIS)

1979-01-01

Ten papers were presented in which chemical pollution due to insecticides was examined in edible oil seeds and their products. They include hexachlorocyclohexane residues in groundnut; carbaryl in groundnut; maize and cotton seed products, and in lactating goats; propoxur in cocoa beans; and leptophos residues in cotton seed and its products and in lactating goats. Eight of these papers constitute separate INIS entries. Egypt, Ghana, India, Korea, Lebanon, Pakistan, the Philippines, Poland, and the Sudan participated under the coordinated research programme. The progress of the programme is reviewed, and problems and priorities for future development of the programme are identified. A number of recommendations are addressed to the Joint FAO/IAEA Secretariat

Thermogravimetric investigation of the co-combustion between the pyrolysis oil distillation residue and lignite.

Science.gov (United States)

Li, Hao; Xia, Shuqian; Ma, Peisheng

2016-10-01

Co-combustion of lignite with distillation residue derived from rice straw pyrolysis oil was investigated by non-isothermal thermogravimetric analysis (TGA). The addition of distillation residue improved the reactivity and combustion efficiency of lignite, such as increasing the weight loss rate at peak temperature and decreasing the burnout temperature and the total burnout. With increasing distillation residue content in the blended fuels, the synergistic interactions between distillation residue and lignite firstly increased and then decreased during co-combustion stage. Results of XRF, FTIR, (13)C NMR and SEM analysis indicated that chemical structure, mineral components and morphology of samples have great influence on the synergistic interactions. The combustion mechanisms and kinetic parameters were calculated by the Coats Redfern model, suggesting that the lowest apparent activation energy (120.19kJ/mol) for the blended fuels was obtained by blending 60wt.% distillation residue during main co-combustion stage. Copyright © 2016 Elsevier Ltd. All rights reserved.

Residual Effect of Chemical and Animal Fertilizers and Compost on Yield, YieldComponents, Physiological Characteristics and Essential Oil Content of Matricaria chamomilla L. under Drought Stress conditions

Directory of Open Access Journals (Sweden)

a Ahmadian

2011-02-01

Full Text Available Abstract The residual effect of inorganic and organic fertilizers on growth and yield of plants is one of the important problems in nutrition. This study was conducted to determine the residual effect of different fertilizers on yield, yield components, physiological parameters and essential oil percentage of Matricaria chamomilla under drought stress. A split plot arrangement based on randomized completely block design (RCBD with three replication was conducted in 2009, at the University of Zabol. Treatments included W1 (non stress, W2 (75% FC and W3 (50% FC as main plot and three types of residual’s fertilizers: F1 (non fertilizer, F2 (chemical fertilizer, F3 (manure fertilizer and F4 (compost as sub plot. Results showed that water stress at W3 treatment reduced dry flower yield. Low water stress increased essential oil percentage and the highest oil was obtained in W2. In this experiment, free proline and total soluble carbohydrate concentration were increased under water stress. The residual’s manure and compost enhanced flower yield, percentage and yield of essential oil of chamomile at the second year. At a glance, animal manure application and light water stress (75% FC was recommended to obtain best quantitative and qualitative yield. Keywords: Water Stress, Fertilizer, Carbohydrate, Proline, Chamomile

Biogas from Agricultural Residues as Energy Source in Hybrid Concentrated Solar Power

NARCIS (Netherlands)

Corré, W.J.; Conijn, J.G.

2016-01-01

This paper explores the possibilities of sustainable biogas use for hybridisation of Concentrated Solar Power (HCSP) in Europe. The optimal system for the use of biogas from agricultural residues (manure and crop residues) in HCSP involves anaerobic digestion with upgrading of biogas to

DEVELOPMENT OF MICROORGANISMS WITH IMPROVED TRANSPORT AND BIOSURFACTANT ACTIVITY FOR ENHANCED OIL RECOVERY

Energy Technology Data Exchange (ETDEWEB)

M.J. McInerney; N. Youssef; T. Fincher; S.K. Maudgalya; M.J. Folmsbee; R. Knapp; D. Nagle

2004-05-31

.1 mM 2,3-butanediol and 1 g/l of partially hydrolyzed polyacrylamide (PHPA) recovered 10-40% of residual oil from Berea sandstone cores. When PHPA was used alone, about 10% of the residual oil was recovered. Interfacial tension (IFT) decreased in a stepwise manner as biosurfactant concentration increased with marked reductions in IFT occurring at biosurfactant concentrations of 10 and 40 mg/l. When the biosurfactant concentration was greater than 10 mg/l, residual oil recovery linearly increased with biosurfactant concentration. A mathematical model that relates oil recovery to biosurfactant concentration was modified to include the stepwise changes in IFT as biosurfactant concentrations changes. This model adequately predicted the experimentally observed changes in IFT as a function of biosurfactant concentration. Our work shows that (1) diverse microorganisms produce biosurfactants, (2) nutrient manipulation may provide a mechanism to increase biosurfactant activity, (3) biosurfactant concentrations in excess of the critical micelle concentration recover substantial amounts of residual oil, and (4) equations that describe the effect of the biosurfactant on IFT adequately predict residual oil recovery in sandstone cores.

Characterization of oil shale, isolated kerogen, and post-pyrolysis residues using advanced 13 solid-state nuclear magnetic resonance spectroscopy

Science.gov (United States)

Cao, Xiaoyan; Birdwell, Justin E.; Chappell, Mark A.; Li, Yuan; Pignatello, Joseph J.; Mao, Jingdong

2013-01-01

Characterization of oil shale kerogen and organic residues remaining in postpyrolysis spent shale is critical to the understanding of the oil generation process and approaches to dealing with issues related to spent shale. The chemical structure of organic matter in raw oil shale and spent shale samples was examined in this study using advanced solid-state 13C nuclear magnetic resonance (NMR) spectroscopy. Oil shale was collected from Mahogany zone outcrops in the Piceance Basin. Five samples were analyzed: (1) raw oil shale, (2) isolated kerogen, (3) oil shale extracted with chloroform, (4) oil shale retorted in an open system at 500°C to mimic surface retorting, and (5) oil shale retorted in a closed system at 360°C to simulate in-situ retorting. The NMR methods applied included quantitative direct polarization with magic-angle spinning at 13 kHz, cross polarization with total sideband suppression, dipolar dephasing, CHn selection, 13C chemical shift anisotropy filtering, and 1H-13C long-range recoupled dipolar dephasing. The NMR results showed that, relative to the raw oil shale, (1) bitumen extraction and kerogen isolation by demineralization removed some oxygen-containing and alkyl moieties; (2) unpyrolyzed samples had low aromatic condensation; (3) oil shale pyrolysis removed aliphatic moieties, leaving behind residues enriched in aromatic carbon; and (4) oil shale retorted in an open system at 500°C contained larger aromatic clusters and more protonated aromatic moieties than oil shale retorted in a closed system at 360°C, which contained more total aromatic carbon with a wide range of cluster sizes.

Concentration of vanadium in crude oil and water using inductively-coupled plasma spectrometry

International Nuclear Information System (INIS)

Amin, Y.M.; Hassan, M.A.; Junkin, K.; Mahat, R.H.; Raphie, B.

1991-01-01

Vanadium is a trace element that is usually associated to crude oil and its products. In this study the concentration of vanadium in a few samples of local crude oil, sea and river water were determined using inductively-coupled plasma spectrometry (ICP). It is hoped that the concentration of vanadium in water can be used to indicate the possible extent of oil contamination

Pro biotic as Alternative to Antibiotic for Broiler Chicken fed Food Industrial Residual Oil

International Nuclear Information System (INIS)

EL-Faramawy, A.A.; El-Maghraby, A.F.; El-Danasoury, M.M.; Hussien, H.A.; Hegazy, E.S.

2016-01-01

This study aimed to evaluate the effect of pro biotic (some lactic acid bacteria) with different levels of food industrial residual oil in broiler commercial diets on growth performance, meat yield, internal organs, economical efficiency and performance index. One hundred and eighty one day old Cobb chicks (45 ± 0.4 g) were equally and randomly divided into 6 groups namely; the antibiotic with fresh oil (FO), the antibiotic with mixed oil (MO) [FO+RO ( 1:1 w/w)], the antibiotic with food industrial residual oil (RO), the pro biotic with FO, the pro biotic with MO and the pro biotic with RO. Virginiamycin, Phibro, USA (15 ppm), was the antibiotic, while a mixture of lactic acid bacteria is chosen as pro biotic. Both were added to the water. During the experiment which lasted for 42 days, the body weight, the feed intake and the mortality rate were recorded at 2, 4 and 6 weeks of age then the body weight gain, feed conversion ratio, economical efficiency and performance index were calculated. The results revealed that the average body weight, body weight gain and feed consumption significantly (P 0.05) while liver increased significantly (P<0.05) in pro biotic FO and gizzard in all pro biotic group and antibiotic MO. The highest performance index was observed in groups of birds treated with pro biotic with MO followed by birds treated with pro biotic FO without significant difference. It could be concluded that supplementation of pro biotic in broiler diet containing different levels of RO was economically more beneficial than antibiotic

Method of concentrating oil shale by flotation

Energy Technology Data Exchange (ETDEWEB)

Larsson, M

1941-01-28

A method is described of concentrating oil shale by flotation. It is characterized by grinding the shale to a grain size which, roughly speaking, is less than 0.06 mm. and more conveniently should be less than 0.05 mm., and followed by flotation. During the process the brown foam formed is separated as concentrate, while the black-brown to all-black foam is separated as a middle product, ground fine again, and thereafter floated once more. The patent contains five additional claims.

Effects of essential oil exposure on salivary estrogen concentration in perimenopausal women.

Science.gov (United States)

Shinohara, Kazuyuki; Doi, Hirokazu; Kumagai, Chizu; Sawano, Erika; Tarumi, Wataru

2017-01-01

The menopausal transition is the time from the onset of menstrual changes until one year after the final menstrual period. During this phase, perimenopausal women experience a variety of health-related symptoms, which seemingly derive from declining level of estrogen secretion. It has long been recognized that some essential oils have the efficacy of alleviating menopausal symptoms. On the basis of this, it is possible that these essential oils have the potency to facilitate estrogen secretion in women. The present study investigated this possibility by examining if the olfactory exposure to the essential oil increase salivary estrogen concentration. We tested the effect of ten essential oils; clary sage, frankincense, geranium, lavender, jasmine absolute, neroli, rose otto, ylang ylang, orange and roman chamomile, which are thought to relieve perimenopasal symptoms. The results have shown increase of salivary estrogen concentration induced by exposure to geranium and rose otto compared to control odor. Together with the previous studies, the present study may give support to the notion that olfactory exposure to some essential oils can influence salivary concentration of estrogen.

Dependences of deposition rate and OH content on concentration of added trichloroethylene in low-temperature silicon oxide films deposited using silicone oil and ozone gas

Science.gov (United States)

Horita, Susumu; Jain, Puneet

2018-03-01

We investigated the dependences of the deposition rate and residual OH content of SiO2 films on the concentration of trichloroethylene (TCE), which was added during deposition at low temperatures of 160-260 °C with the reactant gases of silicone oil (SO) and O3. The deposition rate depends on the TCE concentration and is minimum at a concentration of ˜0.4 mol/m3 at 200 °C. The result can be explained by surface and gas-phase reactions. Experimentally, we also revealed that the thickness profile is strongly affected by gas-phase reaction, in which the TCE vapor was blown directly onto the substrate surface, where it mixed with SO and O3. Furthermore, it was found that adding TCE vapor reduces residual OH content in the SiO2 film deposited at 200 °C because TCE enhances the dehydration reaction.

Safflower oil consumption does not increase plasma conjugated linoleic acid concentrations in humans.

Science.gov (United States)

Herbel, B K; McGuire, M K; McGuire, M A; Shultz, T D

1998-02-01

Conjugated linoleic acid (CLA) is a mixture of positional and geometric isomers of linoleic acid (LA) with conjugated double bonds. CLA has anticarcinogenic properties and has been identified in human tissues, dairy products, meats, and certain vegetable oils. A variety of animal products are good sources of CLA, but plant oils contain much less. However, plant oils are a rich source of LA, which may be isomerized to CLA by intestinal microorganisms in humans. To investigate the effect of triacylglycerol-esterified LA consumption on plasma concentrations of esterified CLA in total lipids, a dietary intervention (6 wk) was conducted with six men and six women. During the intervention period a salad dressing containing 21 g safflower oil providing 16 g LA/d was added to the subjects' daily diets. Three-day diet records and fasting blood were obtained initially and during dietary and postdietary intervention periods. Although LA intake increased significantly during the dietary intervention, plasma CLA concentrations were not affected. Plasma total cholesterol and LDL-cholesterol concentrations were significantly lower after addition of safflower oil to the diet. In summary, consumption of triacylglycerol-esterified LA in safflower oil did not increase plasma concentrations of esterified CLA in total lipids.

Characterization of oil-palm trunk residue degradation enzymes derived from the isolated fungus, Penicillium rolfsii c3-2(1) IBRL.

Science.gov (United States)

Lee, Kok Chang; Arai, Takamitsu; Ibrahim, Darah; Deng, Lan; Murata, Yoshinori; Mori, Yutaka; Kosugi, Akihiko

2016-01-01

This study characterizes crude enzymes derived from Penicillium rolfsii c3-2(1) IBRL, a mesophilic fungus isolated from the local soil of Malaysia. Prior to enzyme activity evaluation, P. rolfsii c3-2(1) IBRL was inoculated into a broth medium containing oil-palm trunk residues for the preparation of crude enzymes. Oil-palm trunk residues were optimally hydrolysed at pH5.0 and 50°C. P. rolfsii c3-2(1) IBRL-derived crude enzymes displayed higher thermal stability compared with the commercial enzymes, Celluclast 1.5 L and Acellerase 1500. Moreover, the hydrolysing activities of the P. rolfsii c3-2(1) IBRL-derived crude enzymes (xylan, arabinan, and laminarin) were superior compared to that of Celluclast 1.5 L and Acellerase 1500, and exhibit 2- to 3-fold and 3- to 4-fold higher oil-palm trunk residues-hydrolysing specific activity, respectively. This higher hydrolysis efficiency may be attributed to the weak 'lignin-binding' ability of the P. rolfsii c3-2(1) IBRL-derived enzymes compared to the commercial enzymes.

Feasibility study on energy saving and environmental improvement via utilization of residual oil at Petron Bataan Refinery

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

A feasibility study has been performed on reduction of global warming gas emission at Bataan Refinery of Petron Company in the Republic of the Philippines by utilizing residual oil in the refinery at high efficiency. In the project, installation will be implemented on thermal power generation equipment using a low-speed diesel engine that uses residual oil as fuel, and a waste heat recovered steam generation system having NOx removing equipment at Bataan Revinary of Petron Company, in addition to the existing boiler-turbine power generation system. As a result of the discussions, the annual energy saving effect in 8 years after the installation will correspond to crude oil of 50,409 tons, and in 20 years cumulatively, it will correspond to 1,017,224 tons. The annual reduction of the global warming gas emission in 8 years after the installation will be 131,698 t-CO2, or 2,657,599 t-CO2 for 20 years cumulatively. The total investment amount for these facilities is about 4.1 billion yen, whereas the investment and energy saving effects were 10.7 tons of crude oil equivalent/year-one million yen. In addition, the investment and global warming gas emission reducing effects were 28.1 t-CO2/year-one million yen. (NEDO)

Study on the pelletizing of sulfate residue with magnetite concentrate in grate-kiln system

Directory of Open Access Journals (Sweden)

Shufeng Y.

2010-01-01

Full Text Available The experiment on the feasibility of pelletizing with magnetite concentrate and the wasted sulfate residue was carried out, to research the performance of pellet in grate-kiln system and simulate the grate-kiln pelletizing process in the micro-pellet roasting simulation system in laboratory, and the process experiments on preheating and roasting sections were conducted. The results show that in order to obtain pellet with good performance and the magnetite concentrate should be over 20 in mass percent, the suitable pelletizing time is about 10 min and moisture is around 12.5%. Also, according to the process parameters of drying and preheating sections obtained from experiment, it will be successful to use magnetite concentrate and the wasted sulfate residue for pelletizing, which exploits a new way for the use of sulfate residue.

Uncertainty of pesticide residue concentration determined from ordinary and weighted linear regression curve.

Science.gov (United States)

Yolci Omeroglu, Perihan; Ambrus, Árpad; Boyacioglu, Dilek

2018-03-28

Determination of pesticide residues is based on calibration curves constructed for each batch of analysis. Calibration standard solutions are prepared from a known amount of reference material at different concentration levels covering the concentration range of the analyte in the analysed samples. In the scope of this study, the applicability of both ordinary linear and weighted linear regression (OLR and WLR) for pesticide residue analysis was investigated. We used 782 multipoint calibration curves obtained for 72 different analytical batches with high-pressure liquid chromatography equipped with an ultraviolet detector, and gas chromatography with electron capture, nitrogen phosphorus or mass spectrophotometer detectors. Quality criteria of the linear curves including regression coefficient, standard deviation of relative residuals and deviation of back calculated concentrations were calculated both for WLR and OLR methods. Moreover, the relative uncertainty of the predicted analyte concentration was estimated for both methods. It was concluded that calibration curve based on WLR complies with all the quality criteria set by international guidelines compared to those calculated with OLR. It means that all the data fit well with WLR for pesticide residue analysis. It was estimated that, regardless of the actual concentration range of the calibration, relative uncertainty at the lowest calibrated level ranged between 0.3% and 113.7% for OLR and between 0.2% and 22.1% for WLR. At or above 1/3 of the calibrated range, uncertainty of calibration curve ranged between 0.1% and 16.3% for OLR and 0% and 12.2% for WLR, and therefore, the two methods gave comparable results.

Separation of thorium (IV) from lanthanide concentrate (LC) and water leach purification (WLP) residue

International Nuclear Information System (INIS)

AL-Areqi, Wadeeah M.; Majid, Amran Ab.; Sarmani, Sukiman

2014-01-01

Thorium (IV) content in industrial residue produced from rare earth elements production industry is one of the challenges to Malaysian environment. Separation of thorium from the lanthanide concentrate (LC) and Water Leach Purification (WLP) residue from rare earth elements production plant is described. Both materials have been tested by sulphuric acid and alkaline digestions. Th concentrations in LC and WLP were determined to be 1289.7 ± 129 and 1952.9±17.6 ppm respectively. The results of separation show that the recovery of Th separation from rare earth in LC after concentrated sulphuric acid dissolution and reduction of acidity to precipitate Th was found 1.76-1.20% whereas Th recovery from WLP was less than 4% after concentrated acids and alkali digestion processes. Inductively Coupled Plasma-Mass Spectroscopy (ICP-MS) was used to determine Th concentrations in aqueous phase during separation stages. This study indicated that thorium maybe exists in refractory and insoluble form which is difficult to separate by these processes and stays in WLP residue as naturally occurring radioactive material (NORM)

Fungitoxic effect of concentrations of essential oils on Colletotrichum gloeosporioides, isolated from the passion fruit

Directory of Open Access Journals (Sweden)

Ismail Teodoro Souza Júnior

2009-09-01

Full Text Available This study aimed to evaluate the effect of different concentrations of essential oils on the fungus Colletotrichum gloeosporioides. The essential oils were obtained from shoots of the plants Lippia sidoides, Ocimum gratissimum, Lippia citriodora, Cymbopogon citratus and Psidium guayava var. pomifera. After the incorporation of oil in water-agar and PDA medium, in concentrations of 1μL/mL, 3μL/mL 5μL/mL and 10μL/mL and witness at 0μL/mL (oil/the culture medium, the inhibitions of conidia germination and mycelial growth, respectively, were evaluates. The results showed that from the concentration of 1μL/mL, essential oils of all plant species had an effect on conidia germination, with an inhibition of 100%. The species Lippia sidoides, Ocimum gratissimum, Lippia citriodora and Cymbopogon citratus inhibited the growth of the fungus mycelium by 100%. The oil of Psidium guayava var. pomifera had progressive control over the mycelium of C. gloeosporioides, in accordance with the increase in concentrations of essential oil.

The Effect of Kaffir Lime Leaves Distillation Residue Oleoresin Concentration on Active Paper Packaging Characteristics

Science.gov (United States)

Kawiji; Utami, R.; Ulum, S.; Khasanah, L. U.; Manuhara, G. J.; Atmaka, W.

2018-03-01

Oleoresin of kaffir lime leaves distillation residue still contains some active compounds such as Citronellal, β-Citronellol, and Linalool which potential to incorporated on the active paper packaging. The purposes of this study were to determine the effect of kaffir lime leaves distillation residue oleoresin concentration on the physical characteristics, sensory characteristics, and antimicrobial activity of the active paper packaging incorporated with kaffir lime leaves distillation residue oleoresin and to determine the functional groups of active paper packaging. The concentration of kaffir lime leaves distillation residue oleoresin were varied at 0%, 2%, 4% and 6%. The result showed that the addition of kaffir lime leaves distillation residue oleoresin increased the thickness and moisture content of the paper and decreased the tensile strengths and folding endurances of active paper packaging. The microbial inhibition tends to increase along with the higher oleoresin concentration addition. Aromatic CH group were found at a wavelength of 897.90 cm-1 of on paper packaging with 2% oleoresin indicated as functional aromatic functional group allegedly obtained from the kaffir lime leaves oleoresin.

Different effects of diets rich in olive oil, rapeseed oil and sunflower-seed oil on postprandial lipid and lipoprotein concentrations and on lipoprotein oxidation susceptibility

DEFF Research Database (Denmark)

Nielsen, Nina Skall; Pedersen, A.; Sandstrøm, B.

2002-01-01

oxidation of fasting and postprandial lipoproteins eighteen males consumed diets enriched with rapeseed oil (RO), olive oil (OO), or sunflower-seed oil (SO) in randomised order for periods of 3 weeks followed by a RO test meal. In the postprandial state the concentrations of cholesterol and triacylglycerol...

Concentrations of viable oil-degrading microorganisms are increased in feces from Calanus finmarchicus feeding in petroleum oil dispersions.

Science.gov (United States)

Størdal, Ingvild Fladvad; Olsen, Anders Johny; Jenssen, Bjørn Munro; Netzer, Roman; Hansen, Bjørn Henrik; Altin, Dag; Brakstad, Odd Gunnar

2015-09-15

Zooplankton are suggested to be biotic contributors to the transport and weathering of oil in marine environments due to their ingestion of oil. In the present experiment, feeding activity and microbial communities in feces from Calanus finmarchicus feeding in oil dispersions were characterized. Feeding activity was significantly reduced in oil dispersions. The microbial communities in clean and oil-containing copepod feces were dominated by Rhodobacteraceae family bacteria (Lesingera, Phaeobacter, Rugeria, and Sulfitobacter), which were suggested to be indigenous to copepod feces. The results also indicated that these bacteria were metabolizing oil compounds, as a significant increase in the concentrations of viable oil degrading microorganisms was observed in oil-containing feces. This study shows that bacteria in feces from copepods feeding in dilute oil dispersions have capacity for degradation of oil. Zooplankton may therefore contribute to weathering of oil by excreting feces with microbial communities already adapted to degradation of oil. Copyright © 2015 Elsevier Ltd. All rights reserved.

Biodegradation of marine oil spill residues using aboriginal bacterial consortium based on Penglai 19-3 oil spill accident, China.

Science.gov (United States)

Wang, Chuanyuan; Liu, Xing; Guo, Jie; Lv, Yingchun; Li, Yuanwei

2018-09-15

Bioremediation, mainly by indigenous bacteria, has been regarded as an effective way to deal with the petroleum pollution after an oil spill accident. The biodegradation of crude oil by microorganisms co-incubated from sediments collected from the Penglai 19-3 oil platform, Bohai Sea, China, was examined. The relative susceptibility of the isomers of alkylnaphthalenes, alkylphenanthrenes and alkyldibenzothiophene to biodegradation was also discussed. The results showed that the relative degradation values of total petroleum hydrocarbon (TPH) are 43.56% and 51.29% for sediments with untreated microcosms (S-BR1) and surfactant-treated microcosms (S-BR2), respectively. TPH biodegradation results showed an obvious decrease in saturates (biodegradation rate: 67.85-77.29%) and a slight decrease in aromatics (biodegradation rate: 47.13-57.21%), while no significant difference of resins and asphaltenes was detected. The biodegradation efficiency of alkylnaphthalenes, alkylphenanthrenes and alkyldibenzothiophene for S-BR1 and S-BR2 samples reaches 1.28-84.43% and 42.56-86.67%, respectively. The efficiency of crude oil degradation in sediment with surfactant-treated microcosms cultures added Tween 20, was higher than that in sediment with untreated microcosms. The biodegradation and selective depletion is not only controlled by thermodynamics but also related to the stereochemical structure of individual isomer compounds. Information on the biodegradation of oil spill residues by the bacterial community revealed in this study will be useful in developing strategies for bioremediation of crude oil dispersed in the marine ecosystem. Copyright © 2018 Elsevier Inc. All rights reserved.

Carbaryl residues in maize and processed products

International Nuclear Information System (INIS)

Qureshi, M.J.; Sattar, A. Jr.; Naqvi, M.H.

1981-01-01

Carbaryl residues in two local maize varieties were determined using a colorimetric method. No significant differences were observed for residues of the two varieties which ranged between 12.0 to 13.75 mg/kg in the crude oil, and averaged 1.04 and 0.67 mg/kg in the flour and cake respectively. In whole maize plants, carbaryl residues declined to approximately 2 mg/kg 35 days after treatment. Cooking in aqueous, oil or aqueous-oil media led to 63-83% loss of carbaryl residues, after 30 minutes. (author)

Characterization of Whey Protein Oil-In-Water Emulsions with Different Oil Concentrations Stabilized by Ultra-High Pressure Homogenization

Directory of Open Access Journals (Sweden)

Essam Hebishy

2017-02-01

Full Text Available In this study, the effect of ultra-high-pressure homogenization (UHPH: 100 or 200 MPa at 25 °C, in comparison to colloid mill (CM: 5000 rpm at 20 °C and conventional homogenization (CH: 15 MPa at 60 °C, on the stability of oil-in-water emulsions with different oil concentrations (10, 30 or 50 g/100 g emulsified by whey protein isolate (4 g/100 g was investigated. Emulsions were characterized for their microstructure, rheological properties, surface protein concentration (SPC, stability to creaming and oxidative stability under light (2000 lux/m2. UHPH produced emulsions containing lipid droplets in the sub-micron range (100–200 nm and with low protein concentrations on droplet surfaces. Droplet size (d3.2, µm was increased in CH and UHPH emulsions by increasing the oil concentration. CM emulsions exhibited Newtonian flow behaviour at all oil concentrations studied; however, the rheological behaviour of CH and UHPH emulsions varied from Newtonian flow (n ≈ 1 to shear-thinning (n ˂ 1 and thixotropic behaviour in emulsions containing 50% oil. This was confirmed by the non-significant differences in the d4.3 (µm value between the top and bottom of emulsions in tubes left at room temperature for nine days and also by a low migration velocity measured with a Turbiscan LAB instrument. UHPH emulsions showed significantly lower oxidation rates during 10 days storage in comparison to CM and CH emulsions as confirmed by hydroperoxides and thiobarbituric acid-reactive substances (TBARS. UHPH emulsions treated at 100 MPa were less oxidized than those treated at 200 MPa. The results from this study suggest that UHPH treatment generates emulsions that have a higher stability to creaming and lipid oxidation compared to colloid mill and conventional treatments.

Computed Tomographic-Guided Radiofrequency Ablation of Recurrent or Residual Hepatocellular Carcinomas around Retained Iodized Oil after Transarterial Chemoembolization

Energy Technology Data Exchange (ETDEWEB)

Koh, Young Hwan [Center for Liver Cancer, National Cancer Center, Goyang 410-769 (Korea, Republic of); Department of Radiology, Research Institute and Hospital, National Cancer Center, Goyang 410-769 (Korea, Republic of); Choi, Joon-Il [Center for Liver Cancer, National Cancer Center, Goyang 410-769 (Korea, Republic of); Department of Radiology, Research Institute and Hospital, National Cancer Center, Goyang 410-769 (Korea, Republic of); Department of Radiology, Seoul St. Mary' s Hospital, College of Medicine, The Catholic University of Korea, Seoul 137-701 (Korea, Republic of); Kim, Hyun Beom [Center for Liver Cancer, National Cancer Center, Goyang 410-769 (Korea, Republic of); Department of Radiology, Research Institute and Hospital, National Cancer Center, Goyang 410-769 (Korea, Republic of); Kim, Min Ju [Department of Radiology, Research Institute and Hospital, National Cancer Center, Goyang 410-769 (Korea, Republic of)

2013-07-01

To assess the clinical efficacy, safety, and risk factors influencing local tumor progression, following CT-guided radiofrequency ablation (RFA) of recurrent or residual hepatocellular carcinoma (HCC), around iodized oil retention. Sixty-four patients (M : F = 51 : 13, 65.0 ± 8.2 years old) with recurrent or residual HCC (75 index tumors, size = 14.0 ± 4.6 mm) had been treated by CT-guided RFA, using retained iodized oil as markers for targeting. The technical success, technique effectiveness rate and complications of RFA were then assessed. On pre-ablative and immediate follow-up CT after RFA, we evaluated the size of enhancing index tumors and iodized oil retention, presence of abutting vessels, completeness of ablation of iodized oil retention, and the presence of ablative margins greater than 5 mm. Also, the time interval between transarterial chemoembolization and RFA was assessed. The cumulative local tumor progression rate was calculated using the Kaplan-Meier method, and the Cox proportional hazards model was adopted, to clarify the independent factors affecting local tumor progression. The technical success and technique effectiveness rate was 100% and 98.7%, respectively. Major complications were observed in 5.6%. The cumulative rates of local tumor progression at 1 and 2 years were 17.5% and 37.5%, respectively. In multivariate analyses, partial ablation of the targeted iodized oil retention was the sole independent predictor of a higher local tumor progression rate. CT-guided RFA of HCC around iodized oil retention was effective and safe. Local tumor progression can be minimized by complete ablation of not only index tumors, but targeted iodized oil deposits as well.

Dual catalyst system for the hydrocracking of heavy oils and residues

Energy Technology Data Exchange (ETDEWEB)

Bellussi, G. [ENI S.p.A., San Donato Milanese (Italy)

2011-07-01

One of the major challenges for our and for the future generations is the development of a sustainable energy supply system based mainly on renewable sources with no environmental impact. This task is necessary to limit the negative effects of green-house gas on the hearth and to allows the forecasted population growth. However, it is not yet clear the time span needed to reach the objective. The total world energy consumption in 2008 amounted to 8428 Mtoe. In a reference scenario, this amount is expected to grow to 16790 Mtoe in 2030 and the contribution expected by sources, according to the International Energy Agency, will be: oil 29.8 %, coal 29.1 %, natural gas 21,2 %, nuclear 5.7 %, hydroelectric 2.4 %, others (Renewable and waste, geothermal, solar, wind, tide,..) [1]. This picture indicates that for several decades, we must still rely on fossil fuels, avoid running out of this precious energy reserves of our planet and reducing the environmental damage arising from their use. For these reason there is a growing need for the efficient upgrading of the heavy oil streams for a better utilization of every barrel of oil produced and for bringing to production also the huge reserves of unconventional fossil sources, such as the heavy oils and the tar sands. Since several years many companies have R and D project aimed to the conversion of heavy residues through a hydrocracking slurry technology, which, with respect to other competing technologies, such as those based on fixed or ebullated bed, can convert all the feedstock to distillates, avoiding the production of fuel oil or coke. In this lecture the advancement in this area will be presented and discussed, highlighting the potentiality offered by the improvement of the catalyst system. (orig.)

Treatment of the press residues of pressed grapes on an industrial scale

Energy Technology Data Exchange (ETDEWEB)

1978-04-24

EtOH and tartaric acid are recovered from press residues of grapes by distillation and concentration of the EtOH and extraction of the dried residue after removal of seeds with a mixture of H/sub 2/O and mineral acid. Vegetable oil is extracted from the seeds. Collidal substances are coagulated by roasting prior to extraction of tartaric acid. The grape skins are recovered in flake form.

Isotope aided studies of pesticide residues during food processing. Report of a final research co-ordination meeting held in Bangkok, Thailand, 31 January - 4 February 1994

International Nuclear Information System (INIS)

1995-08-01

The use of agrochemicals in general and pesticides in particular has greatly aided crop production, protected man from diseases, decreased losses of stored grains and has generally improved man's welfare. One of the steps in ensuring safety of pesticides is adequate monitoring programmes for residue levels in food products and the agricultural environment. Oil-bearing plants often receive heavy pesticide treatment and known to accumulate high concentration of pesticide residues. Technical documents included in this volume report effect of refining or processing of various oil crops like soybean, olive oil, coconut, rapeseed, sunflower cottonseed corn, peanut oil on 14 C-compound pesticide residues. Refs, figs and tabs

Isotope aided studies of pesticide residues during food processing. Report of a final research co-ordination meeting held in Bangkok, Thailand, 31 January - 4 February 1994

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-08-01

The use of agrochemicals in general and pesticides in particular has greatly aided crop production, protected man from diseases, decreased losses of stored grains and has generally improved man`s welfare. One of the steps in ensuring safety of pesticides is adequate monitoring programmes for residue levels in food products and the agricultural environment. Oil-bearing plants often receive heavy pesticide treatment and known to accumulate high concentration of pesticide residues. Technical documents included in this volume report effect of refining or processing of various oil crops like soybean, olive oil, coconut, rapeseed, sunflower cottonseed corn, peanut oil on {sup 14}C-compound pesticide residues.

Estimating sub-surface dispersed oil concentration using acoustic backscatter response.

Science.gov (United States)

Fuller, Christopher B; Bonner, James S; Islam, Mohammad S; Page, Cheryl; Ojo, Temitope; Kirkey, William

2013-05-15

The recent Deepwater Horizon disaster resulted in a dispersed oil plume at an approximate depth of 1000 m. Several methods were used to characterize this plume with respect to concentration and spatial extent including surface supported sampling and autonomous underwater vehicles with in situ instrument payloads. Additionally, echo sounders were used to track the plume location, demonstrating the potential for remote detection using acoustic backscatter (ABS). This study evaluated use of an Acoustic Doppler Current Profiler (ADCP) to quantitatively detect oil-droplet suspensions from the ABS response in a controlled laboratory setting. Results from this study showed log-linear ABS responses to oil-droplet volume concentration. However, the inability to reproduce ABS response factors suggests the difficultly in developing meaningful calibration factors for quantitative field analysis. Evaluation of theoretical ABS intensity derived from the particle size distribution provided insight regarding method sensitivity in the presence of interfering ambient particles. Copyright © 2013 Elsevier Ltd. All rights reserved.

Heavy mineral concentration from oil sand tailings

Energy Technology Data Exchange (ETDEWEB)

Chachula, F.; Erasmus, N. [Titanium Corp. Inc., Regina, SK (Canada)

2008-07-01

This presentation described a unique technique to recover heavy minerals contained in the froth treatment tailings produced by oil sand mining extraction operations in Fort McMurray, Alberta. In an effort to process waste material into valuable products, Titanium Corporation is developing technology to recover heavy minerals, primarily zircon, and a portion of bitumen contained in the final stage of bitumen processing. The process technology is being developed to apply to all mined oil sands operations in the Fort McMurray region. In 2004, Titanium Corporation commissioned a pilot research facility at the Saskatchewan Research Council to test dry oil sands tailings. In 2005, a bulk sampling pilot plant was connected to the fresh oil sands tailings pipeline on-site in Fort McMurray, where washed sands containing heavy minerals were processed at a pilot facility. The mineral content in both deposited tailings and fresh pipeline tailings was assessed. Analysis of fresh tailings on a daily basis identified a constant proportion of zircon and higher levels of associated bitumen compared with the material in the deposited tailings. The process flow sheet design was then modified to remove bitumen from the heavy minerals and concentrate the minerals. A newly modified flotation process was shown to be a viable processing route to recover the heavy minerals from froth treatment tailings. 8 refs., 9 tabs., 12 figs.

STUDY OF ASPHALT BINDER OIL RESIDUE AND MUNICIPAL SOLID WASTE ASH TO BE USED IN LOW TRAFFIC PAVEMENTS

Directory of Open Access Journals (Sweden)

Michéle Dal Toé Casagrande

2014-12-01

Full Text Available The great generation of urban solid has been a concern in several countries. This work presents a study with two materials: the asphalt binder oil residue accumulated in the bottom of asphalt tanks and the municipal solid waste ash, to be used, respectively, as a substitute of conventional binder in asphalt mixtures and for soil stabilization in pavements base layers. Were evaluated properties as the mechanical behavior of the mixtures through experimental tests. The results show the potential of incorporating these residues for low traffic roads, allowing the construction of low cost roads and an environmental use of the residue.

Blood parameters and apparent digestibility of concentrate with rice oil for horses

Directory of Open Access Journals (Sweden)

Helio Alberto Cumani Garcia

2013-10-01

Full Text Available Apparent digestibility coefficients and serum parameters were measured to evaluate the effect of supplementing feed concentrates with rice bran oil in horses. Twelve horses (6 males and 6 females with a mean age of 18 ± 4 months old and mean live weight of 306 ± 22.6 kg were used. Treatments consisted of increasing rice bran oil concentrate levels of 0, 3.5, 7.0, 10.5, 14.0 and 17.5%, considering a daily intake of 2.25% live weight on a dry matter basis. A dietary effect of supplementation on the apparent digestibility of gross energy (y = 64.55 - 0.58x was observed (P0.05. Supplementation did not affect serum glucose levels (P>0.05, but cholesterol was affected (P0.05. A dietary effect on the triglyceride (y = 15.73 - 0.96x + 0.0524x² and HDL (high-density lipoprotein (y = 45.24 + 1.0499x parameters was observed (P<0.01. While the use of rice bran oil does affect blood parameters associated with lipid metabolism, rice bran oil levels up to 17.5% concentrate do not negatively affect the apparent digestibility of dietary nutrients.

The relationship between total phenol concentration and the perceived style of extra virgin olive oil

Energy Technology Data Exchange (ETDEWEB)

Gawel, R.; Rogers, D. A. G.

2009-07-01

The degree of bitterness and pungency of a virgin olive oil largely defines its style, and therefore how it is most appropriately used by consumers. In order to assess how Australian olive oil producers interpret the style of their oils, 920 Australian virgin olive oils were classified by their producers as either being mild, medium or robust in style. Although in general, the classifications by producers were associated with the oils total phenol concentration, significant variability in phenol concentration within each style category was observed. The perceived styles of a subset of these oils were further assessed by panels of expert tasters. The expert panels were more discriminating when assigning oils to style categories based on total phenol levels. The producers and the expert panels were in moderate agreement with respect to oil style, with the interpretation of what constitutes a mild oil being the most contentious. (Author) 16 refs.

Using the candidate gene approach for detecting genes underlying seed oil concentration and yield in soybean.

Science.gov (United States)

Eskandari, Mehrzad; Cober, Elroy R; Rajcan, Istvan

2013-07-01

Increasing the oil concentration in soybean seeds has been given more attention in recent years because of demand for both edible oil and biodiesel production. Oil concentration in soybean is a complex quantitative trait regulated by many genes as well as environmental conditions. To identify genes governing seed oil concentration in soybean, 16 putative candidate genes of three important gene families (GPAT: acyl-CoA:sn-glycerol-3-phosphate acyltransferase, DGAT: acyl-CoA:diacylglycerol acyltransferase, and PDAT: phospholipid:diacylglycerol acyltransferase) involved in triacylglycerol (TAG) biosynthesis pathways were selected and their sequences retrieved from the soybean database ( http://www.phytozome.net/soybean ). Three sequence mutations were discovered in either coding or noncoding regions of three DGAT soybean isoforms when comparing the parents of a 203 recombinant inbreed line (RIL) population; OAC Wallace and OAC Glencoe. The RIL population was used to study the effects of these mutations on seed oil concentration and other important agronomic and seed composition traits, including seed yield and protein concentration across three field locations in Ontario, Canada, in 2009 and 2010. An insertion/deletion (indel) mutation in the GmDGAT2B gene in OAC Wallace was significantly associated with reduced seed oil concentration across three environments and reduced seed yield at Woodstock in 2010. A mutation in the 3' untranslated (3'UTR) region of GmDGAT2C was associated with seed yield at Woodstock in 2009. A mutation in the intronic region of GmDGAR1B was associated with seed yield and protein concentration at Ottawa in 2010. The genes identified in this study had minor effects on either seed yield or oil concentration, which was in agreement with the quantitative nature of the traits. However, the novel gene-specific markers designed in the present study can be used in soybean breeding for marker-assisted selection aimed at increasing seed yield and oil

Multiresidue analysis of pesticides in olive oil by gel permeation chromatography followed by gas chromatography-tandem mass-spectrometric determination

International Nuclear Information System (INIS)

Sanchez, Andres Garcia; Martos, Natividad Ramos; Ballesteros, Evaristo

2006-01-01

A method for the multiresidue analysis of olive oil samples for 26 pesticides is proposed. Residual pesticides are extracted from oil using an n-hexane/acetonitrile mixture, extracts being cleaned-up by gel permeation chromatography (GPC) for analysis by gas chromatography-tandem mass spectrometry (GC-MS/MS). Electron ionization and chemical ionization are employed in a single analysis for the determination of pesticides. Pesticide recoveries from virgin and refined olive oil spiked with 10, 100 and 250 μg/kg concentrations of the pesticides ranged from 83.8 to 110.3%. The proposed method features good sensitivity: its limits of quantification are low enough to allow pesticide residues to be determined at concentrations below the maximum residue levels legally accepted. The precision, expressed as relative standard deviation, ranges from 4.93 to 8.11%. Applicability was tested on 40 olive oil samples. Several pesticides were detected in most of the virgin olive oil samples. By contrast, refined olive samples contained few pesticides, and only endosulfan sulphate was detected in all

Adsorption of crude oil from aqueous solution by hydrogel of chitosan based polyacrylamide prepared by radiation induced graft polymerization

Energy Technology Data Exchange (ETDEWEB)

Sokker, H.H., E-mail: hesham_sokkre@yahoo.com [Jazan University, Faculty of Science (Saudi Arabia); National Center for Radiation Research and Technology, Polymer Chemistry Department, P.O. Box 29, Cairo (Egypt); El-Sawy, Naeem M. [National Center for Radiation Research and Technology, Polymer Chemistry Department, P.O. Box 29, Cairo (Egypt); Hassan, M.A. [Scib Company of Paints, Cairo (Egypt); El-Anadouli, Bahgat E. [Chemistry Department, Faculty of Science, Cairo University, Giza 12613 (Egypt)

2011-06-15

The adsorption of crude oil (initial concentration 0.5-30 g/L) from aqueous solution using hydrogel of chitosan based polyacrylamide (PAM) prepared by radiation induced graft polymerization has been investigated. The prepared hydrogel was characterized by FTIR and SEM micrographs. The experiments were carried out as a function of different initial concentrations of oil residue, acrylamide concentration, contact time and pH to determine the optimum condition for the adsorption of residue oil from aqueous solution and sea water. The results obtained showed that the hydrogel prepared at concentration of 40% acrylamide (AAm) and at a radiation dose of 5 kGy has high removal efficiency of crude oil 2.3 g/g at pH 3. Equilibrium studies have been carried out to determine the capacity of the hydrogel for adsorption of crude oil, Langmuir and Freundlich adsorption models were applied to describe the experimental isotherms and isotherms constants. Equilibrium data were found to fit very well with both Freundlich and Langmuir models. Also the adsorption of oil onto the hydrogel behaves as a pseudo-second-order kinetic models rather than the pseudo-first-order kinetic model.

INVESTIGATION OF DEPENDENCE OF ANTIOXIDANT ACTIVITY OF ESSENTIAL OILS FROM LEMON, MACE, FENNEL AND BLACK PEPPER ON OIL CONCENTRATION BY CAPILLARY GAS-LIQUID CHROMATOGRAPHY

OpenAIRE

Самусенко, Алексей Леонидович

2014-01-01

In recent time the biological activity of essential oils from spicy-aromatic herbs, including the antioxidant one, have been evaluated in numerous studies. Earlier we have demonstrated the high antioxidant activity of the oils contained monoterpenes, such as γ-terpinene and α-terpinolene, or sesquiterpenes (zingeberene and β-caryofillene). However the concentration value of oils in the «aldehyde – essential oil» system was too high and the investigation of various concentrations was not carri...

Degradability of n-alkanes during ex situ natural bioremediation of soil contaminated by heavy residual fuel oil (mazut

Directory of Open Access Journals (Sweden)

Ali Ramadan Mohamed Muftah

2013-01-01

Full Text Available It is well known that during biodegradation of oil in natural geological conditions, or oil pollutants in the environment, a degradation of hydrocarbons occurs according to the well defined sequence. For example, the major changes during the degradation process of n-alkanes occur in the second, slight and third, moderate level (on the biodegradation scale from 1 to 10. According to previous research, in the fourth, heavy level, when intensive changes of phenanthrene and its methyl isomers begin, n-alkanes have already been completely removed. In this paper, the ex situ natural bioremediation (unstimulated bioremediation, without addition of biomass, nutrient substances and biosurfactant of soil contaminated with heavy residual fuel oil (mazut was conducted during the period of 6 months. Low abundance of n-alkanes in the fraction of total saturated hydrocarbons in the initial sample (identification was possible only after concentration by urea adduction technique showed that the investigated oil pollutant was at the boundary between the third and the fourth biodegradation level. During the experiment, an intense degradation of phenanthrene and its methyl-, dimethyl-and trimethyl-isomers was not followed by the removal of the remaining n-alkanes. The abundance of n-alkanes remained at the initial low level, even at end of the experiment when the pollutant reached one of the highest biodegradation levels. These results showed that the unstimulated biodegradation of some hydrocarbons, despite of their high biodegradability, do not proceed completely to the end, even at final degradation stages. In the condition of the reduced availability of some hydrocarbons, microorganisms tend to opt for less biodegradable but more accessible hydrocarbons.

Radiation protection and management of NORM residues in the oil and gas industry

International Nuclear Information System (INIS)

Haridasan, P.P.; )

2014-01-01

The radionuclides in oil and gas streams belong to the decay chains of 238 U and 232 Th originate from the reservoir rock that contains oil, gas and formation water. Formation water contains significant concentrations of isotopes of radium dissolved from the reservoir rock. The parent isotopes of uranium and thorium are not mobilized from the rock and hence the radium isotopes appear in the water co-produced with the oil and gas. When the ions of Group II elements are present in the produced water, drops in pressure and temperature can lead to precipitation of sulphate and carbonate scales on the inner walls of production tubulars, well heads, valves, pumps, separators, water treatment vessels, gas treatment and oil storage tanks. The mixed stream of oil, gas and water carries the radon gas generated in the reservoir rock and in the production stream it preferentially follows the dry export gases. Consequently the equipment from gas treatment and transport facilities may accumulate a thin film of 210 Pb in the inner surfaces of gas lines. The radionuclide concentrations in produced water, hard scale and sludge will be presented. Indication on typical quantities of wastes generated and best practices followed in the industry in managing such wastes will be outlined. Information on external gamma exposure and potential internal exposure as well as global emerging issues will be discussed

Radionuclide concentrations in oil extraction and production processes in Northeast Brazil; Teores de radionuclideos em processos de extracao e de producao de petroleo no nordeste do Brasil

Energy Technology Data Exchange (ETDEWEB)

Gazineu, Maria Helena Paranhos

2005-06-15

Since the beginning of the twentieth century the presence of naturally occurring radioactive material (NORM) was detected in the water and oil extracted from wells both onshore and offshore. The oil is extracted together with water and sediments which contain radionuclides of the uranium and thorium series. Among the radionuclides present, especial attention should be given to {sup 226}Ra and {sup 228}Ra, due to its long half-life and importance, from the radiological point of view. The objective of this work was to identify the natural radionuclides in the oil industry, to determine their activity concentration, and from these results, to evaluate the risks the employees of the oil industry are exposed to. Samples of sludge, scale and produced water extracted with the oil were collected from three oil processing stations in the state of Sergipe, Brazil. The activity concentrations of the radionuclides were determined in the solid samples before and after the extraction of the oil. The chemical and mineralogical composition of the samples without oil was evaluated. Water samples, on the other hand, were analyzed for their contents of radionuclides and barium concentration. It was observed that the activity concentrations of the analyzed radionuclides ({sup 226}Ra, {sup 228}Ra, {sup 228}Th and {sup 210}Pb) in sludge and scales were very high when compared with the literature, particularly much higher than the values for {sup 226}Ra and {sup 228}Ra obtained for sludge and scales from the oil platforms near the city of Campos, state of Rio de Janeiro. The maximum concentration values for {sup 226}Ra, {sup 228}Ra, {sup 228}Th and {sup 210}Pb (3,500, 2,195, 2,248.6 and 201 kBq kg{sup -1}, respectively) were obtained for the scales after the extraction of the oil. The analysis of the samples showed that barium sulphate (barite) and strontium sulphate (celestite) are the main constituents of the scales, while carbonates and silicates, together with other compounds are the

Effect of safflower oil, flaxseed oil, monensin, and vitamin E on concentration of conjugated linoleic acid in bovine milk fat.

Science.gov (United States)

Bell, J A; Griinari, J M; Kennelly, J J

2006-02-01

Conjugated linoleic acid (CLA) refers to a mixture of conjugated octadecadienoic acids of predominantly ruminant origin. The main isomer in bovine milk fat is the cis-9, trans-11 CLA. Interest in CLA increased after the discovery of its health-promoting properties, including potent anticarcinogenic activity. Two experiments were conducted to evaluate dietary strategies aimed at increasing the concentration of CLA in bovine milk fat. Both experiments were organized as a randomized complete block design with a repeated measures treatment structure. In Experiment 1, 28 Holstein cows received either a control diet or one of 3 treatments for a period of 2 wk. The control diet consisted of 60% forage (barley silage, alfalfa silage, and alfalfa hay) and 40% concentrate on a dry matter (DM) basis, fed as a total mixed ration (TMR). The concentrate was partially replaced in the treatment groups with 24 ppm of monensin (MON), 6% of DM safflower oil (SAFF), or 6% of DM safflower oil plus 24 ppm of monensin (SAFF/M). Average cis-9, trans-11 CLA levels in milk fat after 2 wk of feeding were 0.45, 0.52, 3.36, and 5.15% of total fatty acids for control, MON, SAFF, and SAFF/M, respectively. In Experiment 2, 62 Holstein cows received either a control diet or one of 5 treatment diets for a period of 9 wk. The control diet consisted of 60% forage (barley silage, alfalfa silage, and alfalfa hay) and 40% concentrate on a DM basis, fed as a TMR. The concentrate was partially replaced in the treatment groups with 6% of DM safflower oil (SAFF), 6% of DM safflower oil plus 150 IU of vitamin E/kg of DM (SAFF/E), 6% of DM safflower oil plus 24 ppm of monensin (SAFF/M), 6% of DM safflower oil plus 24 ppm of monensin plus 150 IU of vitamin E/kg of DM (SAFF/ME), or 6% of DM flaxseed oil plus 150 IU of vitamin E/kg of DM (FLAX/E). Average cis-9, trans-11 CLA levels during the treatment period were 0.68, 4.12, 3.48, 4.55, 4.75, and 2.80% of total fatty acids for control, SAFF, SAFF/E, SAFF

Improvement of a Vertical Falling Ball Viscometer for Measuring Engine Oil Properties using 532nm diode laser, with Estimation of the Concentration of operated Oil

Directory of Open Access Journals (Sweden)

Dawood O. Altaify

2017-05-01

Full Text Available In this work, an improvement of falling ball viscometer was presented using laser beam. Several parameters such as viscosity, shear stress, shear rate, Reynolds number and drag coefficient were calculated for a sample of unused engine oil. In the other words, during the operation of engine, the variation of viscosity occurs due to the increasing in the engine temperature and may in the increasing of the concentration of engine body particles inside the oil due to friction force even with existing the oil filter there are tiny particles that pass through the oil filter, therefore a Lambert’s law was used to estimate the particles concentrations of the operated oil, the resulted graphs show increasing of the impurities concentration with operation time.

Design and characterization of copaiba oil/alginate films for wound dressings application: Effect of copaiba oil concentration on the film properties

International Nuclear Information System (INIS)

Martins, Aryane Christine Neves; Silva, Classius Ferreira da

2016-01-01

Full text: Polymeric films have been used as wound dressings for burns and wounds. The healing, anti-inflammatory and antibiotic properties of these films can be induced or potentiated by the incorporation of bioactive like herbal medicines. In this work, alginate films were produced incorporating copaiba oil (Copaifera L.) which has the properties as mentioned above. The casting technique was used to prepare the copaiba oil/alginate films. The copaiba oil was previously emulsified in an alginate solution, and the emulsion was cast in a Petri dish before slow drying. The copaiba oil concentration was evaluated. The films were characterized according to the permeability to water vapor, differential scanning calorimetry, scanning electron microscopy, X-ray diffraction, and mechanical properties. The emulsified films showed appropriate properties for use as wound dressings. The main effect on the properties occurred in the highest concentration of copaiba oil. (author)

Design and characterization of copaiba oil/alginate films for wound dressings application: Effect of copaiba oil concentration on the film properties

Energy Technology Data Exchange (ETDEWEB)

Martins, Aryane Christine Neves; Silva, Classius Ferreira da, E-mail: aryanemartins_@hotmail.com [Universidade Federal de Sao Paulo (UNIFESP), Diadema, SP (Brazil)

2016-07-01

Full text: Polymeric films have been used as wound dressings for burns and wounds. The healing, anti-inflammatory and antibiotic properties of these films can be induced or potentiated by the incorporation of bioactive like herbal medicines. In this work, alginate films were produced incorporating copaiba oil (Copaifera L.) which has the properties as mentioned above. The casting technique was used to prepare the copaiba oil/alginate films. The copaiba oil was previously emulsified in an alginate solution, and the emulsion was cast in a Petri dish before slow drying. The copaiba oil concentration was evaluated. The films were characterized according to the permeability to water vapor, differential scanning calorimetry, scanning electron microscopy, X-ray diffraction, and mechanical properties. The emulsified films showed appropriate properties for use as wound dressings. The main effect on the properties occurred in the highest concentration of copaiba oil. (author)

Chronic fuel oil toxicity in American mink (Mustela vison): systemic and hematological effects of ingestion of a low-concentration of bunker C fuel oil

International Nuclear Information System (INIS)

Schwartz, Julie A.; Aldridge, Brian M.; Lasley, Bill L.; Snyder, Paul W.; Stott, Jeff L.; Mohr, F. Charles

2004-01-01

Petroleum oil enters the coastal marine environment through various sources; marine mammals such as sea otters that inhabit this environment may be exposed to low concentrations of petroleum hydrocarbons through ingestion of contaminated prey. The inability to perform controlled studies in free-ranging animals hinders investigations of the effects of chronic petroleum oil exposure on sea otter morbidity and mortality, necessitating the development of a reliable laboratory model. We examined the effects of oral exposure to 500 ppm bunker C fuel oil over 113-118 days on American mink, a species phylogenetically related to the sea otter. Hematological parameters and organs were examined for fuel oil-associated changes. Hepatic cytochrome P4501A1 mRNA expression and fecal cortisol concentrations were also measured. Ingestion of fuel oil was associated with a decrease in erythrocyte count, hemoglobin concentration (Hgb), hematocrit (HCT), and an increase in mean corpuscular volume (MCV). Total leukocytes were elevated in the fuel oil group from increases in neutrophils, lymphocytes, and monocytes. Significant interactions between fuel oil and antigen challenge were found for erythrocyte parameters, monocyte and lymphocyte counts. Liver and adrenal weights were increased although mesenteric lymph node weights were decreased in the fuel oil group. Hepatic cytochrome P4501A1 mRNA was elevated in the fuel oil group. Fecal cortisol concentration did not vary between the two groups. Our findings show that fuel oil exposure alters circulating leukocyte numbers, erythrocyte homeostasis, hepatic metabolism and adrenal physiology and establish a framework to use mink as a model for sea otters in studying the systemic effects of marine contaminants

Use of pre-industrial floodplain lake sediments to establish baseline river metal concentrations downstream of Alberta oil sands: a new approach for detecting pollution of rivers

International Nuclear Information System (INIS)

Wiklund, Johan A; Hall, Roland I; Farwell, Andrea J; George Dixon, D; Wolfe, Brent B; Edwards, Thomas WD

2014-01-01

In the Alberta oil sands region, insufficient knowledge of pre-disturbance reference conditions has undermined the ability of the Regional Aquatics Monitoring Program (RAMP) to detect pollution of the Athabasca River, because sampling began three decades after the industry started and the river naturally erodes oil-bearing strata. Here, we apply a novel approach to characterize pre-industrial reference metal concentrations in river sediment downstream of Alberta oil sands development by analyzing metal concentrations in sediments deposited in floodplain lakes of the Athabasca Delta during 1700–1916, when they were strongly influenced by Athabasca River floodwaters. We compared results to metal concentrations in surficial bottom sediments sampled by RAMP (2010–2013) at downstream sites of the Athabasca River and distributaries. When normalized to lithium content, concentrations of vanadium (a metal of concern in the oil sands region) and other priority pollutants (Be, Cd, Cr, Cu, Pb, Ni, Zn) in nearly all of the RAMP river sediment samples lie below the upper 95% prediction interval linearly extrapolated from the river-derived lake sediments. Assuming the RAMP protocols obtained recently deposited sediment, this indicates that the metal concentrations in downstream Athabasca River sediment have not increased above pre-disturbance levels. Reference conditions derived from the lake sediment data were used to develop profiles of metal residual concentrations versus time for the RAMP river sediment data, which provides an excellent tool for decision-makers to identify and quantify levels of metal pollution for any given sample, and to monitor for future trends. We recommend that the approach be applied to resurrect the utility of RAMP data at other river sampling locations closer to the development, and for ongoing risk assessment. The approach is also readily transferable to other rivers where insufficient pre-disturbance reference data impairs an ability to

Carbaryl residues in cottonseed products in the Philippines

International Nuclear Information System (INIS)

Pablo, F.E.

1981-01-01

Residues of carbaryl in cottonseed products were determined by spectrophotometry. Carbaryl residues in oil and cake were 0.83 and 0.04 mg/kg respectively. Parallel experiments with 14 C-carbaryl gave comparable results. 14 C-carbaryl residues in oil and cake were 0.42 and 0.15 mg/kg respectively. (author)

Identification and concentration of selected pesticide residues in Ghanaian cocoa beans

International Nuclear Information System (INIS)

Sefakor, Adzo Fialor

2017-07-01

Pest and disease have been the major causes of low cocoa production worldwide and the use of chemicals in the form of pesticides is one of the main ways of mitigating their undesirable outcome. However, inappropriate application of pesticides does not only affect the quality of cocoa bean products and the well being of consumers of such products but can also damage the natural flora and fauna in the environment. Hence the reason why evaluating the concentrations of pesticide residues is necessary in establishing the quality of a cocoa. The goal of this study was therefore to determine the concentrations and distribution of specific pesticide residues in cocoa beans from the six cocoa growing regions of Ghana. Three classes of pesticides were tested for in cocoa beans obtained from seventeen (17) districts in the Brong Ahafo, Eastern, Central, Western North, Ashanti and Western South cocoa growing regions of Ghana. These were the neonicotinoids (Thiamethoxam, Clothianidin, Imidacloprid and Acetamiprid); the synthetic pyrethroids (Cypermethrin, Deltamethrin, Fenvalerate, Lambda Cyhalothrin and Permethrin) and the organophosphorous compound Chlorpyrifos. Pesticide residue analyses were done separately on the whole unshelled beans, the nibs and the shells using a GC/ECD for the synthetic pyrethroids and organophosphorous compound and a QqQ-LC/MS for the neonicotinoids. The results obtained showed that the mean concentrations of the neonicotinoids in all the three matrices ranged from <0.001 to 0.018 mg/kg in the shells, <0.001 to 0.0025 mg/kg in the nibs and <0.001 to 0.005 mg/kg in the whole beans with Imidacloprid being the predominant one. Ashanti Region had the highest concentration of Imidacloprid in all the three matrices whilst Eastern Region recorded the least concentration of Imidacloprid in the shells (0.009 mg/kg) and whole unshelled beans (0.002 mg/kg). In relations to the synthetic pyrethroids tested for, the results obtained indicated that out of the

Fish oil concentrate delays sensitivity to thermal nociception in mice

Science.gov (United States)

Veigas, Jyothi M.; Williams, Paul J.; Halade, Ganesh; Rahman, Mizanur M.; Yoneda, Toshiyuki; Fernandes, Gabriel

2011-01-01

Fish oil has been used to alleviate pain associated with inflammatory conditions such as rheumatoid arthritis. The anti-inflammatory property of fish oil is attributed to the n-3 fatty acids docosahexaenoic acid and eicosapentaenoic acid. Contrarily, vegetable oils such as safflower oil are rich in n-6 fatty acids which are considered to be mediators of inflammation. This study investigates the effect of n-3 and n-6 fatty acids rich oils as dietary supplements on the thermally induced pain sensitivity in healthy mice. C57Bl/6J mice were fed diet containing regular fish oil, concentrated fish oil formulation (CFO) and safflower oil (SO) for 6 months. Pain sensitivity was measured by plantar test and was correlated to the expression of acid sensing ion channels (ASICs), transient receptor potential vanilloid 1 (TRPV1) and c-fos in dorsal root ganglion cells. Significant delay in sensitivity to thermal nociception was observed in mice fed CFO compared to mice fed SO (p<0.05). A significant diminution in expression of ion channels such as ASIC1a (64%), ASIC13 (37%) and TRPV1 (56%) coupled with reduced expression of c-fos, a marker of neuronal activation, was observed in the dorsal root ganglion cells of mice fed CFO compared to that fed SO. In conclusion, we describe here the potential of fish oil supplement in reducing sensitivity to thermal nociception in normal mice. PMID:21345372

Bioremediation potential of coal-tar-oil-contaminated soil

International Nuclear Information System (INIS)

Lajoie, C.A.

1991-01-01

The bioremediation of coal tar oil contaminated soil was investigated in 90 day laboratory simulation experiments. The effect of soil moisture, humic acid amendment, and coal tar oil concentration on the rate of disappearance of individual coal tar oil constituents (PAHs and related compounds) was determined by methylene chloride extraction and gas chromatography. Mass balance experiments determined the fate of both the individual 14 C-labeled PAHs phenanthrene, pyrene, and benzo(a)pyrene, and the total coal tar oil carbon. Mineralization, volatilization, incorporation into microbial biomass, disappearance of individual coal tar oil constitutents, and the distribution of residual 14 C-activity in different soil fractions were measured. The rate of disappearance of coal tar oil constituents increased with increasing soil moisture over the experimental range. Humic acid amendment initially enhanced the rate of disappearance, but decreased the extent of disappearance. The amount of contamination removed decreased at higher coal tar oil concentrations. The practical limit for biodegradation in the system tested appeared to be between 1.0 and 2.5% coal tar oil. Mineralization accounted for 40 to 50% of the applied coal tar oil. Volatilization was a minor pathway of disappearance

Determination of oil and fatty acids concentration in seeds of coastal halophytic Sueada aegyptica plant

Directory of Open Access Journals (Sweden)

Tahereh Assadi

2013-04-01

Full Text Available Background: Suaeda aegyptica (S. aegyptica species belong to the Chenepodiaceae family, the second largest family in the world of plants kingdom. It is indigenous to arid and semi-arid regions of the world and salty coastal zones Persian Gulf of Iran. It is an annual succulent halophyte plant which is characterized by producing oily seeds, high growth rate and large number of biomass. The aim of this study was analysis and determination of oil and fatty acids concentration in the S. aegyptica seed. Material and Methods: The seeds of S. aegyptica were collected form coastal zones of Persian Gulf in Bushehr province, washed and dried. The fatty acids content of the dried seeds were extracted in n-hexane solvent by soxhellet apparatus. The residue of n-hexane in oily phase was evaporated by rotary evaporator and remaining oil was collected for fatty acids analysis. In the presence of potassium hydroxide and BF3 by refluxing for 30 minutes, the methyl ester derivative of fatty acids were produced. Then the resulted derivatives were analyzed by gas chromatography (GC-FID. Results: The seeds of S. aegyptica contains eight fatty acids as: Pelargonic (C9, Capric (C10, Undecylic (C11, Tridecylic (C13, Myristic (C14, Palmitic (C16, Stearic (C18, Linoleic (18:2 and Linolenic (18:3. Average oil content in seeds 014/0 ± 87 / percent. Conclusion: The ratio of unsaturated fatty acids was higher than the saturated ones. Linoleic and Palmitic acids are major unsaturated and saturated fatty acids of S. aegyptica seed respectively.

Could residual oil from the Exxon Valdez spill create a long-term population "sink" for sea otters in Alaska?

Science.gov (United States)

Monson, Daniel H.; Doak, Daniel F.; Ballachey, Brenda E.; Bodkin, James L.

2011-01-01

Over 20 years ago, the Exxon Valdez oil tanker spilled 42 million L of crude oil into the waters of Prince William Sound, Alaska, USA. At the time of the spill, the sea otter (Enhydra lutris) population inhabiting the spill area suffered substantial acute injuries and loss. Subsequent research has resulted in one of the best-studied species responses to an oil spill in history. However, the question remains: Is the spill still influencing the Prince William Sound sea otter population? Here we fit time-varying population models to data for the sea otter population of western Prince William Sound to quantify the duration and extent of mortality effects from the spill. We hypothesize that the patchy nature of residual oil left in the environment has created a source-sink population dynamic. We fit models using the age distributions of both living and dying animals and estimates of sea otter population size to predict the number of sea otters in the hypothesized sink population and the number lost to this sink due to chronic exposure to residual oil. Our results suggest that the sink population has remained at just over 900 individuals (95% CI: 606-960) between 1990 and 2009, during which time prime-age survival remained 2-6% below pre-spill levels. This reduced survival led to chronic losses of ???900 animals over the past two decades, which is similar in magnitude to the number of sea otter deaths documented in western Prince William Sound during the acute phase of the spill. However, the unaffected source population appears to be counterbalancing these losses, with the model indicating that the sea otter population increased from ???2150 individuals in 1990 to nearly 3000 in 2009. The most optimistic interpretation of our results suggests that mortality effects dissipated between 2005 and 2007. Our results suggest that residual oil can affect wildlife populations on time scales much longer than previously believed and that cumulative chronic effects can be as

Dual-fuel production from restaurant grease trap waste: bio-fuel oil extraction and anaerobic methane production from the post-extracted residue.

Science.gov (United States)

Kobayashi, Takuro; Kuramochi, Hidetoshi; Maeda, Kouji; Tsuji, Tomoya; Xu, Kaiqin

2014-10-01

An effective way for restaurant grease trap waste (GTW) treatment to generate fuel oil and methane by the combination of physiological and biological processes was investigated. The heat-driven extraction could provide a high purity oil equivalent to an A-grade fuel oil of Japanese industrial standard with 81-93 wt% of extraction efficiency. A post-extracted residue was treated as an anaerobic digestion feedstock, and however, an inhibitory effect of long chain fatty acid (LCFA) was still a barrier for high-rate digestion. From the semi-continuous experiment fed with the residual sludge as a single substrate, it can be concluded that the continuous addition of calcium into the reactor contributed to reducing LCFA inhibition, resulting in the long-term stable operation over one year. Furthermore, the anaerobic reactor performed well with 70-80% of COD reduction and methane productivity under an organic loading rate up to 5.3g-COD/L/d. Copyright © 2014 Elsevier Ltd. All rights reserved.

Multiclass pesticide determination in olives and their processing factors in olive oil: comparison of different olive oil extraction systems.

Science.gov (United States)

Amvrazi, Elpiniki G; Albanis, Triantafyllos A

2008-07-23

The processing factors (pesticide concentration found in olive oil/pesticide concentration found in olives) of azinphos methyl, chlorpyrifos, lambda-cyhalothrin, deltamethrin, diazinon, dimethoate, endosulfan, and fenthion were determined in olive oil production process in various laboratory-scale olive oil extractions based on three- or two-phase centrifugation systems in comparison with samples collected during olive oil extractions in conventional olive mills located at different olive oil production areas in Greece. Pesticide analyses were performed using a multiresidue method developed in our laboratory for the determination of different insecticides and herbicides in olive oil by solid-phase extraction techniques coupled to gas chromatography detection (electron capture detection and nitrogen phosphorus detection), optimized, and validated for olive fruits sample preparation. Processing factors were found to vary among the different pesticides studied. Water addition in the oil extraction procedure (as in a three-phase centrifugation system) was found to decrease the processing factors of dimethoate, alpha-endosulfan, diazinon, and chlorpyrifos, whereas those of fenthion, azinphos methyl, beta-endosulfan, lambda-cyhalothrin, and deltamethrin residues were not affected. The water content of olives processed was found to proportionally affect pesticide processing factors. Fenthion sulfoxide and endosulfan sulfate were the major metabolites of fenthion and endosulfan, respectively, that were detected in laboratory-produced olive oils, but only the concentration of fenthion sulfoxide was found to increase with the increase of water addition in the olive oil extraction process.

The variability in iron speciation in size fractionated residual oil fly ash particulate matter (ROFA PM).

Science.gov (United States)

Pattanaik, Sidhartha; Huggins, Frank E; Huffman, Gerald P

2016-08-15

Ambient particulate matter (PM) containing iron can catalyze Fenton reaction leading to the production of reactive oxygen species in cells. It can also catalyze atmospheric redox reaction. These reactions are governed by the physicochemical characteristics of iron in ambient PM. As a surrogate for ambient PM, we prepared residual oil fly ash PM (ROFA PM) in a practical fire tube boiler firing residual oils with varying sulfur and ash contents. The ROFA particles were resolved into fine PM or PM2.5 (aerodynamic diameter (AD)iron speciation in PM2.5+ was ascertained using X-ray absorption spectroscopy and leaching method while that in PM2.5 was reported earlier. The results of both studies are compared to get an insight into the variability in the iron speciation in different size fractions. The results show the predominance of ferric sulfate, with a minor spinal ferrite in both PM (i.e. ZnxNi1-xFe2O4 in PM2.5, ZnFe2O4 in PM2.5+). The iron solubility in ROFA PM depends on its speciation, mode of incorporation of iron into particle's carbonaceous matrix, the grade and composition of oils, and pH of the medium. The soluble fraction of iron in PM is critical in assessing its interaction with the biological systems and its toxic potential. Copyright © 2016 Elsevier B.V. All rights reserved.

Plasma corticosterone and thyroxine concentrations during chronic ingestion of crude oil in mallard ducks (Anas platyrhynchos)

Science.gov (United States)

Rattner, B.A.; Eastin, W.C.

1981-01-01

1. Blood samples were collected from mallard ducks after 6, 12, and 18 weeks of dietary exposure to mash containing 0.015%, 0.150%, and 1.500% crude oil.2. Plasma corticosterone concentrations in ducks fed mash containing 0.150% or 1.500% Alaskan Prudhoe Bay crude oil were uniformly depressed when compared to values in untreated control birds.3. Plasma thyroxine concentration was not altered in ducks chronically exposed to crude oil.4. The observed alteration in corticosterone concentration could reduce tolerance to temperature and dietary fluctuations in the environment.

eDNA-based bioassessment of coastal sediments impacted by an oil spill.

Science.gov (United States)

Xie, Yuwei; Zhang, Xiaowei; Yang, Jianghua; Kim, Seonjin; Hong, Seongjin; Giesy, John P; Yim, Un Hyuk; Shim, Won Joon; Yu, Hongxia; Khim, Jong Seong

2018-07-01

Oil spills offshore can cause long-term ecological effects on coastal marine ecosystems. Despite their important ecological roles in the cycling of energy and nutrients in food webs, effects on bacteria, protists or arthropods are often neglected. Environmental DNA (eDNA) metabarcoding was applied to characterize changes in the structure of micro- and macro-biota communities of surface sediments over a 7-year period since the occurrence of Hebei Spirit oil spill on December 7, 2007. Alterations in diversities and structures of micro- and macro-biota were observed in the contaminated area where concentrations of polycyclic aromatic hydrocarbons were greater. Successions of bacterial, protists and metazoan communities revealed long-term ecological effects of residual oil. Residual oil dominated the largest cluster of the community-environment association network. Presence of bacterial families (Aerococcaceae and Carnobacteriaceae) and the protozoan family (Platyophryidae) might have conferred sensitivity of communities to oil pollution. Hydrocarbon-degrading bacterial families (Anaerolinaceae, Desulfobacteraceae, Helicobacteraceae and Piscirickettsiaceae) and algal family (Araphid pennate) were resistant to adverse effects of spilt oil. The protistan family (Subulatomonas) and arthropod families (Folsomia, Sarcophagidae Opomyzoidea, and Anomura) appeared to be positively associated with residual oil pollution. eDNA metabarcoding can provide a powerful tool for assessing effects of anthropogenic pollution, such as oil spills on sediment communities and its long-term trends in coastal marine environments. Copyright © 2018 Elsevier Ltd. All rights reserved.

An assessment of ground-level ozone concentrations in the Athabasca oil sands region

International Nuclear Information System (INIS)

1997-01-01

Syncrude and Suncor have plans to develop new oil sands leases and to increase crude oil and bitumen recovery in the Athabasca oil sands region. A first air quality assessment was prepared as part of the Alberta Energy and Utilities Board application, in order to evaluate the emissions and potential impacts associated with the development. The Pembina Institute raised several issues with respect to potential future changes in ambient ozone levels as a result of the Aurora Mine operations. In response to these concerns, another more rigorous assessment was conducted to predict future ground-level ozone concentrations in the Fort McMurray area. This report includes: (1) ambient air quality guidelines for ozone, (2) emissions inventory for dispersion modelling, (3) dispersion modelling methodology, and (4) predicted ambient ozone concentrations. Ground level ozone (O 3 ) concentrations result from anthropogenically produced ozone, and from naturally occurring ozone. Ozone is not directly emitted to the atmosphere from industrial sources, but is formed as a result of chemical reactions between NO x and VOCs, which are emitted from industrial sources within the Athabasca oil sands region. NO x and VOC emissions associated with the Aurora Mine operation are predicted to increase hourly average ozone concentrations in the Fort McMurray area by only 0.001 ppm. 17 refs., 18 tabs., 5 figs

Comprehensive profiling and marker identification in non-volatile citrus oil residues by mass spectrometry and nuclear magnetic resonance.

Science.gov (United States)

Marti, Guillaume; Boccard, Julien; Mehl, Florence; Debrus, Benjamin; Marcourt, Laurence; Merle, Philippe; Delort, Estelle; Baroux, Lucie; Sommer, Horst; Rudaz, Serge; Wolfender, Jean-Luc

2014-05-01

The detailed characterization of cold-pressed lemon oils (CPLOs) is of great importance for the flavor and fragrance (F&F) industry. Since a control of authenticity by standard analytical techniques can be bypassed using elaborated adulterated oils to pretend a higher quality, a combination of advanced orthogonal methods has been developed. The present study describes a combined metabolomic approach based on UHPLC-TOF-MS profiling and (1)H NMR fingerprinting to highlight metabolite differences on a set of representative samples used in the F&F industry. A new protocol was set up and adapted to the use of CPLO residues. Multivariate analysis based on both fingerprinting methods showed significant chemical variations between Argentinian and Italian samples. Discriminating markers identified in mixtures belong to furocoumarins, flavonoids, terpenoids and fatty acids. Quantitative NMR revealed low citropten and high bergamottin content in Italian samples. The developed metabolomic approach applied to CPLO residues gives some new perspectives for authenticity assessment. Copyright © 2013 Elsevier Ltd. All rights reserved.

Improved surfactants formulation for remediation of oil sludge recovery

International Nuclear Information System (INIS)

Syed Hakimi Sakuma Syed Ahmad; Shahidan Radiman

2000-01-01

Surfactant enhanced remediation based on mobilisation of the residual NAPLs (oil sludge) which is radioactive depends on the tendency of the surfactants to lower interfacial tension. Mobilisation has greater potential than solubilisation to increase the rate of remediation. Optimised surfactants formulation was determined with concentration of Aqua 2000 and D Bond of 1% wt respectively, sodium chloride concentration of 2 gmL -1 and addition of 3% wt butanol as cosolvent. The formulation was of benefit not only able to decrease further the interfacial tension of aqueous solution containing oil emulsion, but also to make possible to be more mobile and destruction of mixed liquid crystals that formed. Formation of liquid crystals can hinders significantly recovery efficiency of aqueous solution containing oil emulsion in field remediation work. In a 100 litres soil column experiment conducted containing oil emulsion in field sludge soil and using the surfactants formulation for flushing, miniemulsion formed sizes maintained at average size between 125 nm and 280 nm before and after remediation. Total oil and grease concentration removed from the soil were significant due to the decreased in oil emulsion sizes, increase mobility and solubility. (Author)

Greenhouse gas reductions through enhanced use of residues in the life cycle of Malaysian palm oil derived biodiesel

DEFF Research Database (Denmark)

Hansen, Sune Balle; Olsen, Stig Irving; Ujang, Zaini

2012-01-01

This study identifies the potential greenhouse gas (GHG) reductions, which can be achieved by optimizing the use of residues in the life cycle of palm oil derived biodiesel. This is done through compilation of data on existing and prospective treatment technologies as well as practical experiments...... extraction from empty fruit bunches was found to be the most significant in the biodiesel production life cycle. All the studied waste treatment technologies performed significantly better than the conventional practices and with dedicated efforts of optimized use in the palm oil industry, the production...

Reusing a residue of the oil industry (FCC) in the production of building elements

OpenAIRE

Caicedo Casso, Eduard Andrés; Universidad del Valle; Mejía de Gutiérrez, Ruby; Universidad del Valle; Gordillo Suárez, Marisol; Universidad Autónoma de Occidente; Torres Agredo, Janneth; Universidad Nacional de Colombia, sede Palmira

2015-01-01

This paper analyzes the feasibility of using a residue of spent catalyst (FCC) of the cracking process, from a Colombian oil company, in the production of building elements such as locks and pavers. To define the optimal mix of portland cement/FCC, Portland cement mortars with FCC ratios between 0 and 70% as replacement of cement were prepared and its compressive strength is evaluated at ages up to 28 days of curing. Using a statistical processing, applying the methodology of response, the pr...

Field instruments for real time in-situ crude oil concentration measurements

International Nuclear Information System (INIS)

Fuller, C.B.; Bonner, J.S.; Page, C.A.; Arrambide, G.; Sterling, M.C.Jr.; Ojo, T.O.

2003-01-01

Accidental oil spills, contaminant release during resuspension, storms, and harmful algal blooms are all episodic events that can effect coastal margins. It is important to quantitatively describe water and ecological quality evolution and predict the impact to these areas by such events, but traditional sampling methods miss environmental activity during cyclical events. This paper presents a new sampling approach that involves continuous, real-time in-situ monitoring to provide data for development of comprehensive modeling protocols. It gives spill response coordinators greater assurance in making decisions using the latest visualization tools which are based on a good understanding of the physical processes at work in pulsed events. Five sensors for rapid monitoring of crude oil concentrations in aquatic systems were described. The in-situ and ex-situ sensors can measure plume transport and estimate polycyclic aromatic hydrocarbon exposure concentrations to assess risk of toxicity. A brief description and evaluation of the following 5 sensors was provided: the LISST-100 by Sequoia Instrument, a submersible multi-angle laser scattering instrument; the AU-10 field fluorometer by Turner Designs, an ex-situ single wavelength fluorometer; the Flashlamp by WET Labs Inc., an in-situ single wavelength fluorometer; and, the ECO-FL3 and SAFire by WET Labs Inc., two in-situ multiple wavelength fluorometers. These instruments were used to analyze crude oil emissions of various concentrations. All of the instruments followed a linear response within the tested concentration range. At the lowest concentrations the LISST-100 was not as effective as the fluorometers because of limited particle volume for scatter. For the AU-10 field fluorometer, the highest concentrations tested were above the measurement range of the instrument. 6 refs., 5 figs

Subinhibitory concentrations of perilla oil affect the expression of secreted virulence factor genes in Staphylococcus aureus.

Directory of Open Access Journals (Sweden)

Jiazhang Qiu

Full Text Available BACKGROUND: The pathogenicity of staphylococcus aureus is dependent largely upon its ability to secrete a number of virulence factors, therefore, anti-virulence strategy to combat S. aureus-mediated infections is now gaining great interest. It is widely recognized that some plant essential oils could affect the production of staphylococcal exotoxins when used at subinhibitory concentrations. Perilla [Perilla frutescens (L. Britton], a natural medicine found in eastern Asia, is primarily used as both a medicinal and culinary herb. Its essential oil (perilla oil has been previously demonstrated to be active against S. aureus. However, there are no data on the influence of perilla oil on the production of S. aureus exotoxins. METHODOLOGY/PRINCIPAL FINDINGS: A broth microdilution method was used to determine the minimum inhibitory concentrations (MICs of perilla oil against S. aureus strains. Hemolysis, tumour necrosis factor (TNF release, Western blot, and real-time RT-PCR assays were performed to evaluate the effects of subinhibitory concentrations of perilla oil on exotoxins production in S. aureus. The data presented here show that perilla oil dose-dependently decreased the production of α-toxin, enterotoxins A and B (the major staphylococcal enterotoxins, and toxic shock syndrome toxin 1 (TSST-1 in both methicillin-sensitive S. aureus (MSSA and methicillin-resistant S. aureus (MRSA. CONCLUSIONS/SIGNIFICANCE: The production of α-toxin, SEA, SEB, and TSST-1 in S. aureus was decreased by perilla oil. These data suggest that perilla oil may be useful for the treatment of S. aureus infections when used in combination with β-lactam antibiotics, which can increase exotoxins production by S. aureus at subinhibitory concentrations. Furthermore, perilla oil could be rationally applied in food systems as a novel food preservative both to inhibit the growth of S. aureus and to repress the production of exotoxins, particularly staphylococcal enterotoxins.

Oxidizing oils, etc. [British patent

Energy Technology Data Exchange (ETDEWEB)

Penniman, W B.D.

1926-03-02

The oxidation of crude petroleum and its distillates, shale oils and tars, waxes, sludges, petroleum residues, asphaltic oils, asphalt, malthas, cracked oils and residues from cracking stills, wood tar oils and wood tar, peat and lignite distillates, coal tar oils and coal tar, and oils containing powdered coal, coke or peat, sulphur in suspension, is effected by passing air or other oxygen-containig gas through a layer of the material of a depth sufficient substantially to deoxygenate the air, the pressure being at or below atmospheric pressure.

Upgrading Unconventional Oil Resources with the EST Process

Energy Technology Data Exchange (ETDEWEB)

Delbianco, Alberto; Meli, Salvatori; Panariti, Nicolleta; Rispoli, Giacomo

2007-07-01

We strongly believe that unconventional oils will play a much larger role in the growth of supply than is currently recognized. As a matter of fact, whereas the earth's conventional proven world oil reserves are 1.3 trillion barrels, extra-heavy plus bitumen resources amount to about 4 trillion barrels. The unconventional oils are characterized by low API gravity (<10), high viscosity and high concentration of poisons such as sulphur, nitrogen, metals, and asphaltenes. For this reason, a key role for the full exploitation of these hydrocarbon resources is played by the downstream processes that are required to upgrade and convert them into valuable products. In this scenario, Eni has developed a novel hydrocracking process (EST: Eni Slurry Technology) which is particularly well-suited for the conversion and upgrading of heavy feedstocks (conventional vacuum residues, extra-heavy oils and bitumen). EST employs nano-sized hydrogenation catalysts and an original process scheme that allow complete feedstock conversion to an upgraded synthetic crude oil (SCO) with an API gravity gain greater than 20 and avoid the production of residual by-products, such as pet-coke or heavy fuel oil. A Commercial Demonstration Unit (CDP) of 1200 bbl/d capacity is successfully operating in the Eni's Taranto refinery since November 2005. (auth)

Production performance of lactating dairy cows at pasture fed concentrate supplemented with licuri oil

Directory of Open Access Journals (Sweden)

Luciano dos Santos Lima

2011-12-01

Full Text Available The objective of this study was to determine the optimal level of licuri oil to use in the concentrate of lactating dairy cows on pasture, through growth performance, feed conversion and cost of the supplementation. A total of 16 dairy cows, Holstein × Zebu crossbreed, were kept on Tanzania grass pasture. Cows were divided into four Latin squares, 4 × 4, formed by four experimental periods of 21 days, divided into 17 days for adaptation and four days for data collection. Cows received three kg of concentrate per day at the time of milking, and the treatments consisted of four diets containing licuri oil at levels of 0.0, 1.5, 3.0, and 4.5% of the concentrated dry matter. There was a linear increase in the daily milk yield, corrected to 3.5% fat, and an improvement in the feed conversion of the dry matter and neutral detergent fiber with the inclusion of the licuri oil. The optimal level of licuri oil was 1.5% of the concentrated DM for dairy cows on pasture, whose level has the best profit sale of milk, with positive results in the corrected daily milk production and conversion of the feed nutrients.

Effects of oil and oil burn residues on seabird feathers

DEFF Research Database (Denmark)

Fritt-Rasmussen, Janne; Linnebjerg, Jannie Fries; Sørensen, Martin X.

2016-01-01

It is well known, that in case of oil spill, seabirds are among the groups of animals most vulnerable. Even small amounts of oil can have lethal effects by destroying the waterproofing of their plumage, leading to loss of insulation and buoyancy. In the Arctic these impacts are intensified...

Impact of hydrocarbon type, concentration and weathering on its biodegradability in soil.

Science.gov (United States)

Maletić, Snežana P; Dalmacija, Božo D; Rončević, Srđan D; Agbaba, Jasmina R; Perović, Svetlana D Ugarčina

2011-01-01

The objective of this research was to investigate the impact of the hydrocarbon type and concentration, as well as the total effect of the natural weathering process to hydrocarbon biodegradability in sandy soil and the environment. In this experiment, sandy soil was separately contaminated with 0.5%, 1.0%, 2.0% and 3.5% of diesel and crude oils. Oil contaminated soil was taken from the Oil Refinery dumping sites after 9 years of weathering, and its concentration was adjusted to the above-mentioned levels. The biodegradation process was monitored by measuring CO(2), evolution rate, hydrocarbon degradation rate and dehydrogenase activity. The favourable concentration ranges for the soil contaminated with diesel oil were 1.0%, with concentrations at about 2.0% causing slightly adverse effects to CO(2) production which was overcome after 2 weeks, and with 3.5% diesel oil causing significant toxicity. For soil contaminated with crude oil, 2.0% was found to be optimum for effective biodegradation, with 3.5% crude oil also causing adverse effects to CO(2) production, although less so than the same concentration of diesel oil. No adverse effect was obtained for any concentration of the weathered oil, as after the weathering process, the remaining contaminants in the soil were mostly poorly degradable constituents like asphaltenes, resins etc. It has been proposed that such residual material from oil degradation is analogous to, and can even be regarded as, humic material. Due to its inert characteristics, insolubility and similarity to humic materials it is unlikely to be environmentally hazardous.

In Situ Biodiesel Production from Residual Oil Recovered from Spent Bleaching Earth

Directory of Open Access Journals (Sweden)

Ramli Mat

2011-05-01

Full Text Available Currently, semi-refined and refined vegetable oils are used as a feedstock in biodiesel production. However, due to competition with conventional fossil fuel, economic reasons, shortage supply of food and its social impact on the global scale has somewhat slowed the development of biodiesel industry. Studies have been conducted to recover oil from mill palm oil operation especially from the spent bleaching earth. Hence, the study was to investigate the potential recovery of oil from spent bleaching earth to be used as a feedstock for biodiesel production. The effect of different types of catalysts (sodium hydroxide alkali and sulfuric acid catalysts on biodiesel yield was studied. In addition, the effect of volume addition of methanol to the weight of spent bleaching earth on the product yield was also studied. Furthermore, the effect of ratio of hexane to methanol was also carried out to determine its product yield. The studies were carried out in an in-situ biodiesel reactor system and the biodiesel product was analyzed using gas chromatography mass spectrometry. Result shows that the use of alkali catalyst produced the highest yield of biodiesel and the most optimum biodiesel yield was obtained when the methanol to spent bleaching earth ratio was 3.2:1 (gram of methanol: gram of SBE and hexane to methanol ratio of 0.6:1 (volume of hexane: volume of methanol. © 2011 BCREC UNDIP. All rights reserved(Received: 19th December 2010, Revised: 10th May 2011; Accepted: 18th May 2011[How to Cite: R. Mat, O.S. Ling, A. Johari, M. Mohamed. (2011. In Situ Biodiesel Production from Residual Oil Recovered from Spent Bleaching Earth. Bulletin of Chemical Reaction Engineering & Catalysis, 6(1: 53-57. doi:10.9767/bcrec.6.1.678.53-57][How to Link / DOI: http://dx.doi.org/10.9767/bcrec.6.1.678.53-57 || or local:  http://ejournal.undip.ac.id/index.php/bcrec/article/view/678 ] | View in 

Shale oil. I. Genesis of oil shales and its relation to petroleum and other fuels

Energy Technology Data Exchange (ETDEWEB)

McKee, R H; Manning, P D.V.

1927-01-01

Oil-shale kerogen originated from resinous vegetation residues of past eras, whereas well petroleum was formed from oil shales by pressure and mild heat. Petroleum migrated to its present reservoir from neighboring oil-shale deposits, leaving a residue of black bituminous shales. The high carbon dioxide content of gases present in petroleum wells originated from kerogen, as it gives off carbon dioxide gas before producing soluble oil or bitumen.

Irradiation of residual muds and its use in the oat cultivation

International Nuclear Information System (INIS)

Moreno, A.J.; Colin, C.A.; Gomeztagle, M.M.; Frias, P.H.

1997-01-01

The irradiation of residual muds samples from a wastewater treatment plant at gamma radiation dose of 15 kGy removes from muds on average: fats and oils (33%), detergent (92%), phenols (50%) and over 99% of microorganisms of total account. The evaluation of irradiated residual mud and without irradiation as soil conditioner in oat growing (avena safira), was realized by triplicate, using different rates (80, 60, 40 and 20%) of frank sandy soil and irradiated and non-irradiated residual mud. The growing with rates 60/40 % of soil and irradiated mud respectively, resulted being more adequate as soil conditioner. It is important to clarify that for putting residual mud it is necessary that metals concentration not exceed the maximum permissible levels for the soil type and the corresponding growing. (Author)

Isolation of Crude Oil from Polluted Waters Using Biosurfactants Pseudomonas Bacteria: Assessment of Bacteria Concentration Effects

Directory of Open Access Journals (Sweden)

A. Khalifeh

2013-04-01

Full Text Available Biological decomposition techniques and isolation of environmental pollutions using biosurfactants bacteria are effective methods of environmental protection. Surfactants are amphiphilic compounds that are produced by local microorganisms and are able to reduce the surface and the stresses between surfaces. As a result, they will increase solubility, biological activity, and environmental decomposition of organic compounds. This study analyzes the effects of biosurfactants on crude oil recovery and its isolation using pseudomonas sea bacteria species. Preparation of biosurfactants was done in glass flasks and laboratory conditions. Experiments were carried out to obtain the best concentration of biosurfactants for isolating oil from water and destroying oil-in-water or water-in-oil emulsions in two pH ranges and four saline solutions of different concentrations. The most effective results were gained when a concentration of 0.1% biosurfactants was applied.

Synergistic potential of dillapiole-rich essential oil with synthetic pyrethroid insecticides against fall armyworm

Directory of Open Access Journals (Sweden)

Murilo Fazolin

2016-03-01

Full Text Available ABSTRACT: The objective of this study was to evaluate the synergy and response homogeneity of the Spodoptera frugiperda larvae population to the Piper aduncum essential oil in combination with pyrethroid insecticides (alpha-cypermethrin, beta-cypermethrin, fenpropathrin, and gamma-cyhalothrin compared to piperonylbutoxide (PBO as positive control. Synergism (SF comparisons were obtained using lethal concentration (LC50 and lethal dose (LD50 ratios of insecticides individually and in their respective synergistic combinations with essential oil and PBO. Dose/concentration-mortality slope curves were used to establish relative toxicity increase promoted by synergism. They also determined homogeneity response. Residual contact revealed significant potentiation for commercial insecticides formulated with beta-cypermethrin (SF=9.05-0.5 and fenpropathrin (SF=34.05-49.77 when combined with the P. aduncum essential oil. For topical contact, significant potentiation occurred only for alpha-cypermethrin (SF=7.55-3.68, fenpropathrin (SF=3.37-1.21, and gamma-cyhalothrin (SF=5.79-10.48 insecticides when combined with essential oil. With the exception of fenpropathrin and gamma-cyhalothrin, insecticides synergistic combinations presented homogeneous response by topical as well as residual contact at least with essential oil. The SF significance values ​​of the P. aduncum essential oil combined with alpha-cypermethrin, beta-cypermethrin, fenpropathrin, and gamma-cyhalothrin insecticides indicated potential for this oil to be used as an alternative to PBO.

Application of environmental management system for a energetic plant with oil residual biomass; Aplicacion de un sistema de gestion medio ambiental a una planta generadora de energia que utiliza la biomasa residual del olivar

Energy Technology Data Exchange (ETDEWEB)

Linan Veganzones, M.J.; Soca Olazabal, N.; Pizarro Camacho, D

1998-12-01

Being the alpechin one of the most contaminant residues by the mediterranean agrarian industry, as of today there is no integral depuration procedure. In this paper we show the innovative approach being used to eliminate the alpechin along with the oil miller residual biomass. What it more, the only agroindustrial complex which has introduced such approach is using an EMAS so that actual achievements could be realistically measured. (Author) 12 refs.

Effects of the concentration of emulsion of oil-in-water on the propagation velocity and attenuation

International Nuclear Information System (INIS)

Silva, L S F; Bibiano, D S; Figueiredo, M K K; Costa-Félix, R P B

2015-01-01

Soybean oil is an important feedstock for production of biodiesel that generates about 20 % of oily effluents. This paper studied the effect of concentration of soybean oil-inwater emulsions, in the range from 6 000 to 14 000 ppm, on the propagation velocity and ultrasonic attenuation. The Emission-Reception method has shown that the propagation velocity depends linearly on the concentration. The behavior of attenuation is similar to the velocity. Thus, both parameters can be used to measure oils and greases content in water

Residues of 14C-cyolane in cottonseed products

International Nuclear Information System (INIS)

Zayed, S.M.A.D.; Osman, A.Z.; Fakhr, I.M.I.; Bahig, M.E.

1981-01-01

The systemic insecticide cyolane [2-(0,0-diethylphosphoryl)-imino-1,3-dithiolane] was prepared from 14 C-ethanol, phosphorus oxychloride and 2-amino-1,3-dithiolane. Cotton plants were treated with two applications of the insecticide under conditions of local agricultural practice. 14 C-residues in the crude oil and cake of the harvested cotton seeds amounted to 1.63 and 0.014 mg/kg respectively. About 50% of the 14 C-activity present in the crude oil was found to be eliminated by simulated commercial processes used for refining of the oil. Alkali treatment and bleaching removed 16% and 25% of the radioactive residues respectively. Winterization of the bleached oil at 5-7 0 C for 3 days effected a further elimination of 13%. 14 C-residues in the cotton seed products and in the samples of the refined oil were characterized and the main constituents identified using chromatographic techniques. (author)

Biosurfactants and their role in oil recovery

Energy Technology Data Exchange (ETDEWEB)

McInerney, Michael J. [University of Oklahoma (United States)

2011-07-01

This paper presents the role of biosurfactants in oil recovery. Types of biosurfactants include, among others, lipopeptides, rhamnolipids, sophorolipids. The process of oil recovery and the involvement of microbes are explained. The objective is to know if lipopeptide biosurfactants lower interfacial tension. Fatty acid composition is important for lipopeptide biosurfactant activity and microbial surfactants are hydrophilic and Interfacial Tension (IFT) values are high. Examples of biosurfactants with lower IFT values with mixtures are also given. An experiment was conducted to determine whether lipopeptides recovery entrapped oil or not. The procedure and experimental setup are shown. It is seen that with higher concentration of biosurfactants, the percentage of residual oil recovery is higher. Another experiment was conducted to see if biosurfactants greater than 40 mg/l can be produced in oil reservoirs. The experimental design and the analysis with the results are given. It was seen that more oil was produced. Conclusions from the study were, among other findings, that, in situ biosurfactant production and inoculation are possible.

Evaluation of gastrointestinal solubilization of petroleum hydrocarbon residues in soil using an in vitro physiologically based model.

Science.gov (United States)

Holman, Hoi-Ying N; Goth-Goldstein, Regine; Aston, David; Yun, Mao; Kengsoontra, Jenny

2002-03-15

Petroleum hydrocarbon residues in weathered soils may pose risks to humans through the ingestion pathway. To understand the factors controlling their gastrointestinal (GI) absorption, a newly developed experimental extraction protocol was used to model the GI solubility of total petroleum hydrocarbon (TPH) residues in highly weathered soils from different sites. The GI solubility of TPH residues was significantly higher for soil contaminated with diesel than with crude oil. Compared to the solubility of TPH residues during fasted state,the solubility of TPH residues during fat digestion was much greater. Diesel solubility increased from an average of 8% during the "gallbladder empty" phase of fasting (and less than 0.2% during the otherfasting phase) to an average of 16% during fat digestion. For crude oil, the solubility increased from an average of 1.2% during the gallbladder empty phase of fasting (and undetectable during the other fasting phase) to an average of 4.5% during fat digestion. Increasing the concentration of bile salts also increased GI solubility. GI solubility was reduced by soil organic carbon but enhanced by the TPH content.

Preparation of function-enhanced vegetable oils

Directory of Open Access Journals (Sweden)

Hiroshi Maeda

2016-01-01

Full Text Available Background: Previously, we (HM found that most commercially available edible oils, which were processed by hexane extraction followed by a number of purification steps, were extremely low in anti-peroxy radical (ROO., or radical scavenging activity. This is a great contrast to the respective virgin oils as exemplified by extra-virgin olive oil or crude rape seed oil [1-4] (Figure 1. Therefore, such highly purified oils will became prooxidant and less desirable food components in terms of health oriented diet. Oxidized oils may eventually cause DNA cleavages, modification of proteins, RNA, and lipids, as well as cellular damage, or promote inflammation and carcinogenesis at later time [5-9]. These commercial oils of low antioxidant activity may be improved by adding functionally effective antioxidative components, by using dried vegetable-waste such as tomato-juice-waste-residues and wine-ferment-waste-residues. Their antioxiative components will be transferred into the functionally poor grade edible oils, and consequently, one can improve the quality of such functionally poor oils and thereby contributing human health [2,8,9]. The purpose of this paper is to report a practical procedure to fortify functionally low grade conventional edible oils to functionally enriched edible oils using dried vegetable-waste residues such as tomato juice waste, and wine-ferment-residues, or other vegetable-waste residues. Methods: (1 Preparation and measurements of lycopene and carotenoid enriched oils. To 5.0g or 1.0g of the dried residue of tomato juice waste, 100ml of commercial rape seed (canola oil was added respectively. Each mixture was incubated at room temperature in dark for several weeks. Amount of lycopene and carotenoids extracted into the oil was monitored by increase of absorption (400-550nm and fluorescence at 470nm of carotenoid. Grape-juice ferment (wine waste was similarly prepared after hot air drying, and immersed in canola oil. (2

Soil TPH Concentration Estimation Using Vegetation Indices in an Oil Polluted Area of Eastern China

Science.gov (United States)

Zhu, Linhai; Zhao, Xuechun; Lai, Liming; Wang, Jianjian; Jiang, Lianhe; Ding, Jinzhi; Liu, Nanxi; Yu, Yunjiang; Li, Junsheng; Xiao, Nengwen; Zheng, Yuanrun; Rimmington, Glyn M.

2013-01-01

Assessing oil pollution using traditional field-based methods over large areas is difficult and expensive. Remote sensing technologies with good spatial and temporal coverage might provide an alternative for monitoring oil pollution by recording the spectral signals of plants growing in polluted soils. Total petroleum hydrocarbon concentrations of soils and the hyperspectral canopy reflectance were measured in wetlands dominated by reeds (Phragmites australis) around oil wells that have been producing oil for approximately 10 years in the Yellow River Delta, eastern China to evaluate the potential of vegetation indices and red edge parameters to estimate soil oil pollution. The detrimental effect of oil pollution on reed communities was confirmed by the evidence that the aboveground biomass decreased from 1076.5 g m−2 to 5.3 g m−2 with increasing total petroleum hydrocarbon concentrations ranging from 9.45 mg kg−1 to 652 mg kg−1. The modified chlorophyll absorption ratio index (MCARI) best estimated soil TPH concentration among 20 vegetation indices. The linear model involving MCARI had the highest coefficient of determination (R 2 = 0.73) and accuracy of prediction (RMSE = 104.2 mg kg−1). For other vegetation indices and red edge parameters, the R2 and RMSE values ranged from 0.64 to 0.71 and from 120.2 mg kg−1 to 106.8 mg kg−1 respectively. The traditional broadband normalized difference vegetation index (NDVI), one of the broadband multispectral vegetation indices (BMVIs), produced a prediction (R 2 = 0.70 and RMSE = 110.1 mg kg−1) similar to that of MCARI. These results corroborated the potential of remote sensing for assessing soil oil pollution in large areas. Traditional BMVIs are still of great value in monitoring soil oil pollution when hyperspectral data are unavailable. PMID:23342066

Refining shale-oil distillates

Energy Technology Data Exchange (ETDEWEB)

Altpeter, J

1952-03-17

A process is described for refining distillates from shale oil, brown coal, tar, and other tar products by extraction with selective solvents, such as lower alcohols, halogen-hydrins, dichlorodiethyl ether, liquid sulfur dioxide, and so forth, as well as treating with alkali solution, characterized in that the distillate is first treated with completely or almost completely recovered phenol or cresotate solution, the oil is separated from the phenolate with solvent, for example concentrated or adjusted to a determined water content of lower alcohol, furfural, halogen-hydrin, dichlorodiethyl ether, liquid sulfur dioxide, or the like, extracted, and the raffinate separated from the extract layer, if necessary after distillation or washing out of solvent, and freeing with alkali solution from residual phenol or creosol.

Emissions of polycyclic aromatic hydrocarbons from the combustion of crude oil on water

International Nuclear Information System (INIS)

Benner, B.A. Jr.; Bryner, N. P.; Wise, S.A.; Mulholland, G.W.; Evans, D.D.; Fingas, M.F.; Li, K.

1991-01-01

A study was conducted to examine some of the factors necessary to assess the environmental impact of an in-situ burn of an oil spill on water. These factors include the fraction of an oil layer which can be burned, the quantity of smoke emitted, and the concentrations of 18 polycyclic aromatic hydrocarbons (PAHs) in the smoke, crude oil, and burn residue. Alberta sweet mixed blend crude in 1, 3, 5, 10, and 30 mm layers on water was burned in the laboratory and smoke samples were collected at elevated and ambient temperatures and analyzed by two independent laboratories. While burning the crude oil produced less total PAHs than was in the original crude, the concentrations of PAHs with 5 or more rings were 10-20 times greater in the smoke than in the oil. The organic carbon fraction of the smoke was in the 14-21% range. As the fuel layer thickness was increased from 2 to 10 mm, the smoke yield increased from 0.035 g smoke/g fuel and the percentage of oil residue decreased from 46% to 17%. By consuming much of the oil spill and reducing the amount of PAHs in the water, and by dispersing the combustion products over a larger area, in-situ burning can mitigate the local environmental impact of an oil spill. There appears to be a range of situations, such as in Arctic ice fields, where in-situ burning might be the most viable cleanup method. 25 refs., 6 figs., 6 tabs

On-site monitoring of Hebei Spirit oil spill by fluorometric detection of oil residues in coastal waters off Taean, Korea

Energy Technology Data Exchange (ETDEWEB)

Kim, M.; Yim, U.H.; Hong, S.H.; Jung, J.H.; Won, J.; An, J.; Choi, H.W.; Shim, W.J. [Korea Ocean Research and Development Inst., Geoje (Korea, Republic of)

2009-07-01

This paper discussed activities conducted to monitor a crude oil spill that contaminated over 70 km of the western Korean coastline. Contamination levels and temporal variations of dissolved and dispersed oils in sea and pore water at 40 beaches were monitored using a portable fluorimeter for 10 months after the spill. More than 980 samples from the heavily-impacted Mallipo Beach area were analyzed. The analysis showed that oil concentrations in the sea water were as high as 16,600 {mu}g/L directly after the spill, and decreased to below the Korean marine water quality standard of 10 {mu}g/L at most sites 10 months after the spill. However, the oil content in pore water remained high, with levels of up to 2,320 {mu}g/L for the first few months following the spill. Higher oil contamination levels were observed at some sites for up to 10 months after the spill. Results of the study suggested that oil in pore water persisted in confined areas along the coastline. Results from the fluorescence detection technique were then compared with traditional gas chromatography (GC) techniques of total petroleum hydrocarbon analysis. It was concluded that fluorescence detection was capable of generating accurate results more quickly and cost-effectively than traditional GC techniques. 22 refs., 7 figs.

Modification of Optical Properties of Seawater Exposed to Oil Contaminants Based on Excitation-Emission Spectra

Science.gov (United States)

Baszanowska, E.; Otremba, Z.

2015-10-01

The optical behaviour of seawater exposed to a residual amount of oil pollution is presented and a comparison of the fluorescence spectra of oil dissolved in both n-hexane and seawater is discussed based on excitation-emission spectra. Crude oil extracted from the southern part of the Baltic Sea was used to characterise petroleum properties after contact with seawater. The wavelength-independent fluorescence maximum for natural seawater and seawater artificially polluted with oil were determined. Moreover, the specific excitation-emission peaks for natural seawater and polluted water were analysed to identify the natural organic matter composition. It was found that fluorescence spectra identification is a promising method to detect even an extremely low concentration of petroleum residues directly in the seawater. In addition, alien substances disturbing the fluorescence signatures of natural organic substances in a marine environment is also discussed.

INFLUENCE OF SELENIUM CONTENT AND OIL SOURCES IN FEED ON CONCENTRATION OF THYROID GLAND HORMONES AND ELECTROLYTE IN BROILER BLOOD

Directory of Open Access Journals (Sweden)

Zlata Kralik

2014-12-01

Full Text Available The research aimed to elaborate the influence of designed mixtures used in broilers fattening on the concentration of electrolytes and thyroid gland hormones in the blood.. The research was carried out on 120 male Ross 308 hybrid broilers. The fattening lasted for 42 days. During the first three weeks of fattening broilers were fed standard starter diet containing 22% crude protein and 13.90 MJ/kg ME. During the last three weeks of fattening, broilers were divided into 6 experimental groups, each fed specially prepared finisher diets (P1=6% sunflower oil+0.0 mg Se/kg of feed, P2=6% linseed oil+0.0 mg Se/kg of feed, P3=6% sunflower oil+0.3 mg Se/kg of feed, P4=6% linseed oil+0.3 mg Se/kg of feed, P5=6% sunflower oil+0.5 mg Se/kg of feed, P6=6% linseed oil+0.5 mg Se/kg of feed. Finisher diet was balanced at 18.02% crude protein and 14.40 MJ/kg ME. It was found out that the type of oil in chicken feed influenced to blood pH (P <0.001, whereas selenium level (P=0.014 in the feed, as well as the oil type and selenium level interaction (P<0.001 influenced the concentration of potassium in the blood. Oil type (P=0.037 influenced the concentration of fT3, which was lower in chickens fed mixtures with addition of linseed oil than in the chickens fed sunflower oil added mixtures. Interaction of selenium content and oil type had influence on differences in concentration of fT4 as well as on the ratio of fT3/fT4, (P<0.001, i.e. P=0.021. The research results indicated that oils supplemented to broiler diets and combined with different organic selenium concentrations affected pH, concentration of some electrolytes and thyroid gland hormones in broiler blood, however, all obtained values were within reference range for poultry.

Preparation of hydraulic cement from oil-shale

Energy Technology Data Exchange (ETDEWEB)

1921-08-28

A process for the preparation of hydraulic cement from oil-shale or oil-shale residue is characterized in that, the oil-shale or shale-coke together with a slight amount of marl is burned under sintering conditions and the residue obtained is ground to a fine dust.

A Review of distribution and quantity of lingering subsurface oil from the Exxon Valdez Oil Spill

Science.gov (United States)

Nixon, Zachary; Michel, Jacqueline

2018-01-01

Remaining lingering subsurface oil residues from the Exxon Valdez oil spill (EVOS) are, at present, patchily distributed across the geologically complex and spatially extensive shorelines of Prince William Sound and the Gulf of Alaska. We review and synthesize previous literature describing the causal geomorphic and physical mechanisms for persistence of oil in the intertidal subsurface sediments of these areas. We also summarize previous sampling and modeling efforts, and refine previously presented models with additional data to characterize the present-day linear and areal spatial extent, and quantity of lingering subsurface oil. In the weeks after the spill in March of 1989, approximately 17,750 t of oil were stranded along impacted shorelines, and by October of 1992, only 2% of the mass of spilled oil was estimated to remain in intertidal areas. We estimate that lingering subsurface residues, generally between 5 and 20 cm thick and sequestered below 10-20 cm of clean sediment, are present over 30 ha of intertidal area, along 11.4 km of shoreline, and represent approximately 227 t or 0.6% of the total mass of spilled oil. These residues are typically located in finer-grained sand and gravel sediments, often under an armor of cobble- or boulder-sized clasts, in areas with limited groundwater flow and porosity. Persistence of these residues is correlated with heavy initial oil loading together with localized sheltering from physical disturbance such as wave energy within the beach face. While no longer generally bioavailable and increasingly chemically weathered, present removal rates for these remaining subsurface oil residues have slowed to nearly zero. The only remaining plausible removal mechanisms will operate over time scales of decades.

The residual C concentration control for low temperature growth p-type GaN

International Nuclear Information System (INIS)

Liu Shuang-Tao; Zhao De-Gang; Yang Jing; Jiang De-Sheng; Liang Feng; Chen Ping; Zhu Jian-Jun; Liu Zong-Shun; Li Xiang; Liu Wei; Xing Yao; Zhang Li-Qun

2017-01-01

In this work, the influence of C concentration to the performance of low temperature growth p-GaN is studied. Through analyses, we have confirmed that the C impurity has a compensation effect to p-GaN. At the same time we have found that several growth and annealing parameters have influences on the residual C concentration: (i) the C concentration decreases with the increase of growth pressure; (ii) we have found there exists a Ga memory effect when changing the Cp 2 Mg flow which will lead the growth rate and C concentration increase along the increase of Cp 2 Mg flow; (iii) annealing outside of metal–organic chemical vapor deposition (MOCVD) could decrease the C concentration while in situ annealing in MOCVD has an immobilization role to C concentration. (paper)

GC/MS determination of bicyclic sesquiterpanes in crude oils and petroleum products

International Nuclear Information System (INIS)

Yang, C.; Wang, Z.; Hollebone, B.; Brown, C.E.; Landriault, M.

2008-01-01

A study was conducted in which sesquiterpanes, a component of crude oils and petroleum products, were identified and characterized in an effort to determine the feasibility of using them as biomarkers for fingerprinting and identifying unknown lighter petroleum product spills. The study compared the distributions of sesquiterpanes in different oils, oil distillation fractions and refined products, including light and mid-range distillate fuels, residual fuels and lubricating oils. Evaporative weathering effects on sesquiterpane distribution and concentration were quantitatively studied and several diagnostic indices of sesquiterpane were developed for oil correlation and differentiation. Bicyclic sesquiterpanes in crude oils and oil products have much different abundances and distributions. Therefore, the relevant sesquiterpane ratios are different. Bicyclic sesquiterpanes are mostly partitioned into the medium distillation fractions. The study showed that concentrations of sesquiterpanes in crude oil and diesel fuel increase in proportion with the increase of weathering percentages. Relevant diagnostic ratios therefore remained stable. It was concluded that C 15 and C 16 sesquiterpanes may be alternative internal tracers to provide a direct way to estimate the depletion of oils, particularly diesels, in oil spill investigations. 13 refs., 6 tabs., 4 figs

Linseed oil supplemented concentrate fed to Brahman crossbred fattening steers on carcass quality traits and intramuscular fatty acid profiles

Directory of Open Access Journals (Sweden)

Pitunart Noosen

2017-02-01

Full Text Available The objective of this study was to determine the linseed oil supplemented concentrate fed to Brahman crossbred fattening steers on carcass quality trait and intramuscular fatty acid (FA profiles. All steers were fed 14% CP concentrate. The treatments included: (1 7 kg/d concentrate; (2 4 kg/d concentrate supplemented with 200 g/d palm oil (PO; (3 4 kg/d concentrate supplemented with 100 g/d PO and 100 g/d linseed oil (LSO; and (4 4 kg/d concentrate supplemented with 200 g/d LSO. The animals in the treatment 1 were fed ad libitum rice straw (RS, whereas the animals in other treatments were fed ad libitum fresh grass (FG. Dietary treatments had no effect on nutrient intake while oil supplement decreased dry matter intake (DMI. Inclusion of LSO did not negatively affect carcass quality, but increasing amount of LSO supplement increased the n-3 fatty acids and lowered the n-6/n-3 ratio in beef

The effect of andiroba oil and chitosan concentration on the physical properties of chitosan emulsion film

Directory of Open Access Journals (Sweden)

Vanessa Tiemi Kimura

Full Text Available Abstract Chitosan film is used as a dressing to heal burns. The physical and biological properties of the film can be modified by the addition of phytotherapic compounds. This work used the casting -solvent evaporation technique to prepare chitosan film containing andiroba oil (Carapa guianensis which has anti-inflammatory, antibiotic, and healing properties. The objective of this study was to determine the effect of the concentrations of chitosan and andiroba oil on the physical properties of chitosan films. The emulsion films were evaluated concerning the mechanical properties and fluid handling capacity. Additionally, scanning electron microscopy and thermal analysis were performed. The results showed that the barrier and mechanical properties were affected by the addition of andiroba oil, and these may be modulated as a function of the concentration of oil added to the film. The thermal analysis showed no evidence of chemical interactions between the oil and chitosan.

A tiered analytical protocol for the characterization of heavy oil residues at petroleum-contaminated hazardous waste sites

International Nuclear Information System (INIS)

Pollard, S.J.T.; Kenefick, S.L.; Hrudey, S.E.; Fuhr, B.J.; Holloway, L.R.; Rawluk, M.

1994-01-01

The analysis of hydrocarbon-contaminated soils from abandoned refinery sites in Alberta, Canada is used to illustrate a tiered analytical approach to the characterization of complex hydrocarbon wastes. Soil extracts isolated from heavy oil- and creosote-contaminated sites were characterized by thin layer chromatography with flame ionization detection (TLC-FID), ultraviolet fluorescence, simulated distillation (GC-SIMDIS) and chemical ionization GC-MS analysis. The combined screening and detailed analytical methods provided information essential to remedial technology selection including the extent of contamination, the class composition of soil extracts, the distillation profile of component classes and the distribution of individual class components within various waste fractions. Residual contamination was characteristic of heavy, degraded oils, consistent with documented site operations and length of hydrocarbon exposure at the soil surface

Study of the sediment contamination levels in a mangrove swamp polluted by a marine oil spill

Energy Technology Data Exchange (ETDEWEB)

Wong, T.W.Y.; Ke, L.; Wong, Y.S.; Tam, N.F.Y. [City University of Hong Kong, Hong Kong SAR (China)

2002-07-01

The pattern of oil retention in mangrove sediments was studied in an effort to determine the temporal changes of petroleum hydrocarbon concentrations and composition several months after oil spills occur. Mangroves are inter-tidal wetlands in tropical and subtropical coastlines. Due to the anoxic and water logging characteristics of mangrove sediments, oil residues linger much longer in these wetlands compared to other coastal habitats. In November 2000, an accidental oil spill occurred in the Pearl River Estuary in which approximately 230,000 litres of crude oil was leaked from an oil tanker. The spilled oil migrated to the YiO, a typical mangrove swamp in Hong Kong Special Administrative Region. The degree of oil contamination in the sediments depended on the sediment texture and topography of the mangrove. The total petroleum hydrocarbon (TPH) concentration of the sediments in the most affected area near a freshwater creek flowing into the sea was 130 times higher than normal, one month after the accident. The mean TPH concentration was 2862 ug/g of dry sediment while the mean carbon preference index was 1.22 compared to the background value of 3.97. The temporal changes of the petroleum hydrocarbon level in 5 defined areas were examined for 7 months after the spill. The most polluted area next to the creek was determined to have very high TPH levels in the muddy sediments even 7 months after the spill. Oil residues infiltrated as deep as 20 cm into the sediments, making it more difficult to degrade than surface pollution and posing long-term adverse effects on trees in the area. It was determined that with growing industrialization and increasing demands for fuel and energy supply, mangroves in South China should be ranked as top priority for protection from oil spills. 19 refs., 6 tabs., 6 figs.

Study of the sediment contamination levels in a mangrove swamp polluted by a marine oil spill

International Nuclear Information System (INIS)

Wong, T.W.Y.; Ke, L.; Wong, Y.S.; Tam, N.F.Y.

2002-01-01

The pattern of oil retention in mangrove sediments was studied in an effort to determine the temporal changes of petroleum hydrocarbon concentrations and composition several months after oil spills occur. Mangroves are inter-tidal wetlands in tropical and subtropical coastlines. Due to the anoxic and water logging characteristics of mangrove sediments, oil residues linger much longer in these wetlands compared to other coastal habitats. In November 2000, an accidental oil spill occurred in the Pearl River Estuary in which approximately 230,000 litres of crude oil was leaked from an oil tanker. The spilled oil migrated to the YiO, a typical mangrove swamp in Hong Kong Special Administrative Region. The degree of oil contamination in the sediments depended on the sediment texture and topography of the mangrove. The total petroleum hydrocarbon (TPH) concentration of the sediments in the most affected area near a freshwater creek flowing into the sea was 130 times higher than normal, one month after the accident. The mean TPH concentration was 2862 ug/g of dry sediment while the mean carbon preference index was 1.22 compared to the background value of 3.97. The temporal changes of the petroleum hydrocarbon level in 5 defined areas were examined for 7 months after the spill. The most polluted area next to the creek was determined to have very high TPH levels in the muddy sediments even 7 months after the spill. Oil residues infiltrated as deep as 20 cm into the sediments, making it more difficult to degrade than surface pollution and posing long-term adverse effects on trees in the area. It was determined that with growing industrialization and increasing demands for fuel and energy supply, mangroves in South China should be ranked as top priority for protection from oil spills. 19 refs., 6 tabs., 6 figs

Prediction of Dissolved Gas Concentrations in Transformer Oil Based on the KPCA-FFOA-GRNN Model

Directory of Open Access Journals (Sweden)

Jun Lin

2018-01-01

Full Text Available The purpose of analyzing the dissolved gas in transformer oil is to determine the transformer’s operating status and is an important basis for fault diagnosis. Accurate prediction of the concentration of dissolved gas in oil can provide an important reference for the evaluation of the state of the transformer. A combined predicting model is proposed based on kernel principal component analysis (KPCA and a generalized regression neural network (GRNN using an improved fruit fly optimization algorithm (FFOA to select the smooth factor. Firstly, based on the idea of using the dissolved gas ratio of oil to diagnose the transformer fault, gas concentration ratios are also used as characteristic parameters. Secondly, the main parameters are selected from the feature parameters using the KPCA method, and the GRNN is then used to predict the gas concentration in the transformer oil. In the training process of the network, the FFOA is used to select the smooth factor of the neural network. Through a concrete example, it is shown that the method proposed in this paper has better data fitting ability and more accurate prediction ability compared with the support vector machine (SVM and gray model (GM methods.

Evaluating the effect of chemical agents on the displacement coefficient of crude oils using a centrifuging method

Energy Technology Data Exchange (ETDEWEB)

Kuznetsov, B M; Tulbovich, B I

1974-01-01

A centrifuge was used to determine effectiveness of surfactants in displacing oil from carbonate and terrigenous cores. Essential procedure was to centrifuge the cores, weigh them after each experimental step, and extract to determine residual oil saturation. The 3 surfactants used in this experimental program were a nonionic agent, trisodium phosphate, and a mixture of benzene sulfonates and alkylphenol ethers. The agents were used at 0.05 to 1% concentration. From 9 to 27% of normally unrecoverable oil was recovered with surfactants. The most effective material was the mixture of benzene sulfonates and alkylphenol ethers, used at 0.1% concentration.

Monitoring and modeling wetland chloride concentrations in relationship to oil and gas development

Science.gov (United States)

Post van der Burg, Max; Tangen, Brian A.

2015-01-01

Extraction of oil and gas via unconventional methods is becoming an important aspect of energy production worldwide. Studying the effects of this development in countries where these technologies are being widely used may provide other countries, where development may be proposed, with some insight in terms of concerns associated with development. A fairly recent expansion of unconventional oil and gas development in North America provides such an opportunity. Rapid increases in energy development in North America have caught the attention of managers and scientists as a potential stressor for wildlife and their habitats. Of particular concern in the Northern Great Plains of the U.S. is the potential for chloride-rich produced water associated with unconventional oil and gas development to alter the water chemistry of wetlands. We describe a landscape scale modeling approach designed to examine the relationship between potential chloride contamination in wetlands and patterns of oil and gas development. We used a spatial Bayesian hierarchical modeling approach to assess multiple models explaining chloride concentrations in wetlands. These models included effects related to oil and gas wells (e.g. age of wells, number of wells) and surficial geology (e.g. glacial till, outwash). We found that the model containing the number of wells and the surficial geology surrounding a wetland best explained variation in chloride concentrations. Our spatial predictions showed regions of localized high chloride concentrations. Given the spatiotemporal variability of regional wetland water chemistry, we do not regard our results as predictions of contamination, but rather as a way to identify locations that may require more intensive sampling or further investigation. We suggest that an approach like the one outlined here could easily be extended to more of an adaptive monitoring approach to answer questions about chloride contamination risk that are of interest to managers.

Insecticides authorized for use on olive trees and the relationship between their registration and residues in olive oil

Directory of Open Access Journals (Sweden)

Lentza-Rizos, Ch.

1996-12-01

Full Text Available In order to eliminate losses due to insect attack, several insecticides are used on olive trees. Their residues in olive oil constitute an important parameter of its quality and must be monitored regularly and kept as low possible in order to ensure consumer protection. In this paper the insecticides authorized for use on olive trees are listed and their ADIs and Codex Alimentarius MRLs reported. The existing registrations are discussed from the point of view of their residues in oil.

Diversos insecticidas son usados para eliminar las pérdidas debidas al ataque de insectos en olivos. Sus residuos en el aceite de oliva constituyen un parámetro importante de su calidad y deben ser controlados con regularidad y mantenidos tan bajos como sea posible en orden a asegurar la protección del consumidor. En este artículo se incluyen los distintos insecticidas autorizados para su uso en olivos así como los valores de ingesta diaria aceptable para el hombre y los límites máximos autorizados de los mismos. Los registros existentes se discuten desde el punto de vista de sus residuos en el aceite.

Air Pollution Modelling to Predict Maximum Ground Level Concentration for Dust from a Palm Oil Mill Stack

Directory of Open Access Journals (Sweden)

Regina A. A.

2010-12-01

Full Text Available The study is to model emission from a stack to estimate ground level concentration from a palm oil mill. The case study is a mill located in Kuala Langat, Selangor. Emission source is from boilers stacks. The exercise determines the estimate the ground level concentrations for dust to the surrounding areas through the utilization of modelling software. The surround area is relatively flat, an industrial area surrounded by factories and with palm oil plantations in the outskirts. The model utilized in the study was to gauge the worst-case scenario. Ambient air concentrations were garnered calculate the increase to localized conditions. Keywords: emission, modelling, palm oil mill, particulate, POME

Residual Sorption and leaching of the herbicide diuron following de-oiled two-phase olive mill waste addition to soil

Energy Technology Data Exchange (ETDEWEB)

Lopez-Pineiro, A.; Albarran, A.; Cabrera, D.; Rato, J. M.; Munoz, A.; Flores, S.

2009-07-01

The residual sorption, desorption, degradation, and leaching of the herbicide diuron (3-(3,4-dichlorophenyl)-1,1-dimethylurea) a herbicide widely used in olive groves, was studied following the addition to soils of de oiled two-phase olive mill waste (DTPOMW). Field experiments were conducted on an olive grove soil amended over seven years with DTPOMW. (Author)

Residual Sorption and leaching of the herbicide diuron following de-oiled two-phase olive mill waste addition to soil

International Nuclear Information System (INIS)

Lopez-Pineiro, A.; Albarran, A.; Cabrera, D.; Rato, J. M.; Munoz, A.; Flores, S.

2009-01-01

The residual sorption, desorption, degradation, and leaching of the herbicide diuron (3-(3,4-dichlorophenyl)-1,1-dimethylurea) a herbicide widely used in olive groves, was studied following the addition to soils of de oiled two-phase olive mill waste (DTPOMW). Field experiments were conducted on an olive grove soil amended over seven years with DTPOMW. (Author)

Oxidation in fish oil-enriched mayonnaise 4 : Effect of tocopherol concentration on oxidative deterioration

DEFF Research Database (Denmark)

Jacobsen, Charlotte; Hartvigsen, Karsten; Lund, Pia

2001-01-01

The effect of the water-dispersible tocopherol preparation, Grindox 1032, and the oil-soluble tocopherol preparation, Toco 70, on oxidative stability in fish oil-enriched mayonnaise was examined. The two commercial antioxidant preparations were supplemented in different levels corresponding to 20......-280 ppm tocopherol in addition to the 600 ppm present in the oils used for the mayonnaise. The oxidative stability was assessed by sensory analysis, the tendency of formation of free radicals, and concentrations of lipid hydroperoxides and volatile oxidation products. The effect of tocopherol on oxidation...... depended on the nature and the concentration of the tocopherol preparation employed, and it also depended on the parameters evaluated. Addition of high levels of Grindox 1032 (similar to 140-280 ppm tocopherol) thus decreased the intensity of rancid off-flavor, but increased the formation of fishy off...

Experimental and theoretical study of the influence of water on hydrolyzed product formation during the feruloylation of vegetable oil.

Science.gov (United States)

Compton, David L; Evans, Kervin O; Appell, Michael

2017-07-01

Feruloylated vegetable oil is a valuable green bioproduct that has several cosmeceutical applications associated with its inherent anti-oxidant and ultraviolet-absorption properties. Hydrolyzed vegetable oil by-products can influence product quality and consistency. The formation of by-products by residual water in the enzymatic synthesis of feruloylated vegetable oil was investigated using chemical theory and experimental studies by monitoring the reaction over a 22-day period. The hydrolysis of vegetable oil is thermodynamically favored over the hydrolysis of the ethyl ferulate starting material. These results suggest that hydrolyzed vegetable oil products will be experimentally observed in greater concentrations compared to hydrolyzed ethyl ferulate products. Quantum chemical studies identified several reaction mechanisms that explain the formation of side products by water, suggesting that residual water influences product quality. Efforts to reduce residual water can improve product consistency and reduce purification costs. Published 2016. This article is a U.S. Government work and is in the public domain in the USA. Published 2016. This article is a U.S. Government work and is in the public domain in the USA.

Distribution of radium in oil and gas industry wastes from Malaysia

International Nuclear Information System (INIS)

Omar, M.; Ali, H.M.; Abu, M.P.; Kontol, K.M.; Ahmad, Z.; Ahmad, S.H.S.S.; Sulaiman, I.; Hamzah, R.

2004-01-01

Radium concentrations in 470 samples of the various types of waste from oil and gas industries were analysed using gamma spectrometers. The results showed that the radium concentration varied within a wide range. The highest mean 226 Ra and 228 Ra concentrations of 114,300 and 130,120 Bq/kg, respectively, were measured in scales. Overall, 75% of the waste, mostly sludge and extraction residue lies within the normal range of radium concentration in soils of Malaysia. However, some platform sludge can have radium concentration up to 560 Bq/kg

Distribution of radium in oil and gas industry wastes from Malaysia.

Science.gov (United States)

Omar, M; Ali, H M; Abu, M P; Kontol, K M; Ahmad, Z; Ahmad, S H S S; Sulaiman, I; Hamzah, R

2004-05-01

Radium concentrations in 470 samples of the various types of waste from oil and gas industries were analysed using gamma spectrometers. The results showed that the radium concentration varied within a wide range. The highest mean 226Ra and 228Ra concentrations of 114,300 and 130,120 Bq/kg, respectively, were measured in scales. Overall, 75% of the waste, mostly sludge and extraction residue lies within the normal range of radium concentration in soils of Malaysia. However, some platform sludge can have radium concentration up to 560 Bq/kg.

Crude oil burning mechanisms

DEFF Research Database (Denmark)

van Gelderen, Laurens; Malmquist, L.M.V.; Jomaas, Grunde

2015-01-01

In order to improve predictions for the burning efficiency and the residue composition of in-situ burning of crude oil, the burning mechanism of crude oil was studied in relation to the composition of its hydrocarbon mixture, before, during and after the burning. The surface temperature, flame...... height, mass loss rate and residues of three hydrocarbon liquids (n-octane, dodecane and hexadecane), two crude oils (DUC and REBCO) and one hydrocarbon liquid mixture of the aforementioned hydrocarbon liquids were studied using the Crude Oil Flammability Apparatus. The experimental results were compared...... on the highest achievable oil slick temperature. Based on this mechanism, predictions can then be made depending on the hydrocarbon composition of the fuel and the measured surface temperature....

40 CFR 279.47 - Management of residues.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 26 2010-07-01 2010-07-01 false Management of residues. 279.47 Section 279.47 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) SOLID WASTES (CONTINUED... Management of residues. Transporters who generate residues from the storage or transport of used oil must...

Impact of heavy metals on the oil products biodegradation process.

Science.gov (United States)

Zukauskaite, Audrone; Jakubauskaite, Viktorija; Belous, Olga; Ambrazaitiene, Dalia; Stasiskiene, Zaneta

2008-12-01

Oil products continue to be used as a principal source of energy. Wide-scale production, transport, global use and disposal of petroleum have made them major contaminants in prevalence and quantity in the environment. In accidental spills, actions are taken to remove or remediate or recover the contaminants immediately, especially if they occur in environmentally sensitive areas, for example, in coastal zones. Traditional methods to cope with oil spills are confined to physical containment. Biological methods can have an advantage over the physical-chemical treatment regimes in removing spills in situ as they offer biodegradation of oil fractions by the micro-organisms. Recently, biological methods have been known to play a significant role in bioremediation of oil-polluted coastal areas. Such systems are likely to be of significance in the effective management of sensitive coastal ecosystems chronically subjected to oil spillage. For this reason the aim of this paper is to present an impact of Mn, Cu, Co and Mo quantities on oil biodegradation effectiveness in coastal soil and to determine the relationship between metal concentrations and degradation of two oil products (black oil and diesel fuel). Soil was collected in the Baltic Sea coastal zone oil products degradation area (Klaipeda, Lithuania). The experiment consisted of two parts: study on the influence of micro-elements on the oil product biodegradation process; and analysis of the influence of metal concentration on the number of HDMs. The analysis performed and results obtained address the following areas: impact of metal on a population of hydrocarbon degrading micro-organisms, impact of metals on residual concentrations of oil products, influence of metals on the growth of micro-organisms, inter-relation of metal concentrations with degradation rates. Statistical analysis was made using ;Statgraphics plus' software. The influence of metals on the growth of micro-organisms, the biodegradation process

The Effects of Combination of High Intensity Intermittent Exercise and Supplement Flaxseed Oil 1 ICAM- Plasma Concentration in Male Rats

Directory of Open Access Journals (Sweden)

Y Khademi

2017-01-01

Full Text Available Introduction: Prevalence of cardiovascular diseases is rooted in inflammation and inflammation is along with the increase of ICAM-1. The aim of the present study was to review the effect of combination of high interval training and flaxseed oil supplementation on plasma concentration of ICAM-1 of rats. Methods: In this experimental study, 30 rats were selected and divided into six groups of five male rats, including (1 control, (2 training, (3 10 mg/kg Flaxseed oil, (4 30 mg/kg Flaxseed oil, (5 training with 10 mg/kg Flaxseed oil and (6 training with 30 mg/kg Flaxseed oil. Groups of 2, 5 and 6 were trained with high intensity interval training for 10 weeks and five sessions per week, also groups 3 to 6 received flaxseed oil for 10 weeks. For statistical analysis of data two way ANOVA test was used (p≤0.05. Results: 10 weeks  treating high intensity interval training  for 10 weeks had significant effect on the increase of the plasma concentration of ICAM-1 of male rats (p=0.001. Nevertheless, Taking 10 weeks 10 and 30 mg/kg flaxseed oil supplementation for 10 weeks has significant effect on reducing  the plasma concentration of ICAM-1 of rats (p=0.001. Training and taking flaxseed oil supplementation have interactional effect on reduingc the plasma concentration of ICAM-1 of male rats (p=0.001. Conclusion: Combination of high intensity interval training and flaxseed oil supplementation has interactional effects on the improvement of plasma concentration of ICAM-1 in male rats.

Life-Cycle Assessment of Pyrolysis Bio-Oil Production*

Energy Technology Data Exchange (ETDEWEB)

Steele, Philip; Puettmann, Maureen E.; Penmetsa, Venkata Kanthi; Cooper, Jerome E.

2012-07-01

As part ofthe Consortium for Research on Renewable Industrial Materials' Phase I life-cycle assessments ofbiofuels, lifecycle inventory burdens from the production of bio-oil were developed and compared with measures for residual fuel oil. Bio-oil feedstock was produced using whole southern pine (Pinus taeda) trees, chipped, and converted into bio-oil by fast pyrolysis. Input parameters and mass and energy balances were derived with Aspen. Mass and energy balances were input to SimaPro to determine the environmental performance of bio-oil compared with residual fuel oil as a heating fuel. Equivalent functional units of 1 MJ were used for demonstrating environmental preference in impact categories, such as fossil fuel use and global warming potential. Results showed near carbon neutrality of the bio-oil. Substituting bio-oil for residual fuel oil, based on the relative carbon emissions of the two fuels, estimated a reduction in CO2 emissions by 0.075 kg CO2 per MJ of fuel combustion or a 70 percent reduction in emission over residual fuel oil. The bio-oil production life-cycle stage consumed 92 percent of the total cradle-to-grave energy requirements, while feedstock collection, preparation, and transportation consumed 4 percent each. This model provides a framework to better understand the major factors affecting greenhouse gas emissions related to bio-oil production and conversion to boiler fuel during fast pyrolysis.

Estimation of the residual bromine concentration after disinfection of cooling water by statistical evaluation.

Science.gov (United States)

Megalopoulos, Fivos A; Ochsenkuehn-Petropoulou, Maria T

2015-01-01

A statistical model based on multiple linear regression is developed, to estimate the bromine residual that can be expected after the bromination of cooling water. Make-up water sampled from a power plant in the Greek territory was used for the creation of the various cooling water matrices under investigation. The amount of bromine fed to the circuit, as well as other important operational parameters such as concentration at the cooling tower, temperature, organic load and contact time are taken as the independent variables. It is found that the highest contribution to the model's predictive ability comes from cooling water's organic load concentration, followed by the amount of bromine fed to the circuit, the water's mean temperature, the duration of the bromination period and finally its conductivity. Comparison of the model results with the experimental data confirms its ability to predict residual bromine given specific bromination conditions.

Concentrations of the genotoxic metals, chromium and nickel, in whales, tar balls, oil slicks, and released oil from the gulf of Mexico in the immediate aftermath of the deepwater horizon oil crisis: is genotoxic metal exposure part of the deepwater horizon legacy?

Science.gov (United States)

Wise, John Pierce; Wise, James T F; Wise, Catherine F; Wise, Sandra S; Gianios, Christy; Xie, Hong; Thompson, W Douglas; Perkins, Christopher; Falank, Carolyne; Wise, John Pierce

2014-01-01

Concern regarding the Deepwater Horizon oil crisis has largely focused on oil and dispersants while the threat of genotoxic metals in the oil has gone largely overlooked. Genotoxic metals, such as chromium and nickel, damage DNA and bioaccumulate in organisms, resulting in persistent exposures. We found chromium and nickel concentrations ranged from 0.24 to 8.46 ppm in crude oil from the riser, oil from slicks on surface waters and tar balls from Gulf of Mexico beaches. We found nickel concentrations ranged from 1.7 to 94.6 ppm wet weight with a mean of 15.9 ± 3.5 ppm and chromium concentrations ranged from 2.0 to 73.6 ppm wet weight with a mean of 12.8 ± 2.6 ppm in tissue collected from Gulf of Mexico whales in the wake of the crisis. Mean tissue concentrations were significantly higher than those found in whales collected around the world prior to the spill. Given the capacity of these metals to damage DNA, their presence in the oil, and their elevated concentrations in whales, we suggest that metal exposure is an important understudied concern for the Deepwater Horizon oil disaster.

Residual antibiofilm effects of various concentrations of double antibiotic paste used during regenerative endodontics after different application times.

Science.gov (United States)

Jenks, Daniel B; Ehrlich, Ygal; Spolnik, Kenneth; Gregory, Richard L; Yassen, Ghaeth H

2016-10-01

We investigated the residual antibiofilm effects of different concentrations of double antibiotic paste (DAP) applied on radicular dentin for 1 or 4 weeks. Dentin samples were prepared (n=120), sterilized and pretreated for 1 or 4 weeks with the clinically used concentration of DAP (500mg/mL), low concentrations of DAP (1, 5 or 50mg/mL) loaded into a methylcellulose system, calcium hydroxide (Ca(OH) 2 ), or placebo paste. After the assigned treatment time, treatment pastes were rinsed off and the samples were kept independently in phosphate buffered saline for 3 weeks. Pretreated dentin samples were then inoculated with Enterococcus faecalis and bacterial biofilms were allowed to grow for an additional 3 weeks. Biofilms were then retrieved from dentin using biofilm disruption assays, diluted, spiral plated, and quantified. Fisher's Exact and Wilcoxon rank sum tests were used for statistical comparisons (α=0.05). Dentin pretreatment for 4 weeks with 5, 50 or 500mg/mL of DAP demonstrated significantly higher residual antibiofilm effects and complete eradication of E. faecalis biofilms in comparison to a 1 week pretreatment with similar concentrations. However, dentin pretreated with 1mg/mL of DAP or Ca(OH) 2 did not provide a substantial residual antibiofilm effect regardless of the application time. Dentin pretreatment with 5mg/mL of DAP or higher for 4 weeks induced significantly higher residual antibiofilm effects in comparison to a 1 week pretreatment with the same concentrations. Copyright © 2016 Elsevier Ltd. All rights reserved.

Fuel oil and kerosene sales 1997

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-08-01

The Fuel Oil and Kerosene Sales 1997 report provides information, illustrations and state-level statistical data on end-use sales of kerosene; No. 1, No. 2, and No. 4 distillate fuel oil; and residual fuel oil. State-level kerosene sales include volumes for residential, commercial, industrial, farm, and all other uses. State-level distillate sales include volumes for residential, commercial, industrial, oil company, railroad, vessel bunkering, military, electric utility, farm, on-highway, off highway construction, and other uses. State-level residual fuel sales include volumes for commercial, industrial, oil company, vessel bunkering, military, electric utility, and other uses. 24 tabs.

Fuel oil and kerosene sales 1997

International Nuclear Information System (INIS)

1998-08-01

The Fuel Oil and Kerosene Sales 1997 report provides information, illustrations and state-level statistical data on end-use sales of kerosene; No. 1, No. 2, and No. 4 distillate fuel oil; and residual fuel oil. State-level kerosene sales include volumes for residential, commercial, industrial, farm, and all other uses. State-level distillate sales include volumes for residential, commercial, industrial, oil company, railroad, vessel bunkering, military, electric utility, farm, on-highway, off highway construction, and other uses. State-level residual fuel sales include volumes for commercial, industrial, oil company, vessel bunkering, military, electric utility, and other uses. 24 tabs

Decomposition of PCBs in transformer oil using an electron beam accelerator

International Nuclear Information System (INIS)

Jung, In-Ha; Lee, Myun-Joo; Mah, Yoon-Jung

2012-01-01

Decomposition of PCBs in commercially used transformer oil used for more than 30 years has been carried out at normal temperature and pressure without any additives using an electron beam accelerator. The experiments were carried out in two ways: batch and continuous pilot plant with 1.5 MeV of energy, a 50 mA current, and 75 kW of power in a commercial scale accelerator. The electron beam irradiation seemed to transform large molecular weight compounds into lower ones, but the impact was considered too small on the physical properties of oil. Residual concentrations of PCBs after irradiation depend on the absorption dose of the electron beam energy, but aliphatic chloride compounds were produced at higher doses of irradiation. As the results from FT-NMR, chloride ions decomposed from the PCBs are likely to react with aliphatic hydro carbon compounds rather than existing as free radical ions in the transformer oil. Since this is a dry process, treated oil can be used as cutting oil or machine oil for heavy equipment without any additional treatments. - Highlights: ► We developed a novel technology of decomposing PCBs in transformer oil using an electron beam. ► Distinct feature is accomplishing at ambient temperature and pressure without any additives. ► Residual PCBs were depended on absorption dose, but aliphatic chlorides were produced at higher dose. ► Treated oil can be reused as heating oil with chlorine removal technology developed here.

Antioxidant activity of rosemary essential oil fractions obtained by molecular distillation and their effect on oxidative stability of sunflower oil.

Science.gov (United States)

Mezza, Gabriela N; Borgarello, Ana V; Grosso, Nelson R; Fernandez, Héctor; Pramparo, María C; Gayol, María F

2018-03-01

The objective of this study was to evaluate the antioxidant activity of rosemary essential oil fractions obtained by molecular distillation (MD) and investigate their effect on the oxidative stability of sunflower oil. MD fractions were prepared in a series of low-pressure stages where rosemary essential oil was the first feed. Subsequently, a distillate (D1) and residue (R1) were obtained and the residue fraction from the previous stage used as the feed for the next. The residue fractions had the largest capacity to capture free radicals, and the lowest peroxide values, conjugated dienes and conjugated trienes. The antioxidant activity of the fractions was due to oxygenated monoterpenes, specifically α-terpineol and cis-sabinene hydrate. Oxidative stability results showed the residues (R1 and R4) and butylated hydroxytoluene had greater antioxidant activity than either the distillate fractions or original rosemary essential oil. The residue fractions obtained by short path MD of rosemary essential oil could be used as a natural antioxidants by the food industry. Copyright © 2017. Published by Elsevier Ltd.

Hydrogenizing oils, asphalts, etc

Energy Technology Data Exchange (ETDEWEB)

1925-03-14

The hydrogenation of carbonaceous solids in presence of combined sulfur, e.g., sulfides as described in the parent specification is applied to the treatment of rock oils, shale oils, resins, ozokerite, asphalt, and the like, or fractions, residues, or acid sludge or other conversion products thereof, alone or mixed. Preferably the hydrogen or other reducing gas is in excess and under pressure, and is either circuited or led through a series of treatment vessels, hydrogen being added for that used. In an example, residues from American crude oil are passed continuously with hydrogen at 200 atmospheres and 450 to 500/sup 0/C over pressed precipitated cobalt sulfide, the issuing gases being cooled to condense the light oil produced.

Proceedings: 1993 fuel oil utilization workshop

International Nuclear Information System (INIS)

1994-08-01

The primary objective of the Workshop was to utilize the experiences of utility personnel and continue the interchange of information related to fuel oil issues. Participants also identified technical problem areas in which EPRI might best direct its efforts in research and development of fuel oil utilization and to improve oil-fired steam generating systems' performance. Speakers presented specific fuel projects conducted at their particular utilities, important issues in the utilization of fuel oil, studies conducted or currently in the process of being completed, and information on current and future regulations for fuel utilization. Among the major topics addressed at the 1993 Fuel Oil Utilization Workshop were burner and ESP improvements for the reduction of particulate and NO x emissions, practical experience in utilization of low API gravity residual fuel oils, the use of models to predict the spread of oil spills on land, implementing OPA 90 preparedness and response strategies planning, a report on the annual Utility Oil Buyers Conference, ASTM D-396 specification for No. 6 fuel oil, the utilization of Orimulsion reg-sign in utility boilers, recent progress on research addressing unburned carbon and opacity from oil-fired utility boilers, EPRI's hazardous air pollutant monitoring and implications for residual fuel oil, and the feasibility of toxic metals removal from residual fuel oils. Selected papers are indexed separately for inclusion in the Energy Science and Technology Database

The Galeta Oil Spill. III. Chronic Reoiling, Long-term Toxicity of Hydrocarbon Residues and Effects on Epibiota in the Mangrove Fringe

Science.gov (United States)

Levings, Sally C.; Garrity, Stephen D.; Burns, Kathryn A.

1994-04-01

In April 1986, 75 000-100 000 barrels of medium-weight crude oil (˜ 10 000-13 500 metric tons) spilled into Bahía las Minas, a large mangrove-lined bay on the Caribbean coast of Panamá. Between 1986 and 1991, biological and chemical effects of this spill were studied. The epibiota of fringing mangroves ( Rhizophora mangle L.) were examined in three habitats: (1) the shoreward margins of reef flats that fronted the open sea, (2) the edges of channels and lagoons, and (3) the banks of streams and man-made cuts that drained interior mangroves or uplands into lagoons. Chemical analyses of bivalves collected from submerged prop roots (oysters and false mussels) and records of slicks and tarry deposits on artificial roots documented chronic reoiling. Each habitat was repeatedly oiled between 1986 and 1991, with petroleum residues identified as the oil spilled in 1986. There was a decline in the release of tarry oils recorded as slicks and on roots over time, but not in tissue burdens of hydrocarbons in bivalves. This suggested that the processes that released these different types of oil residues were at least partially independent and that toxic hydrocarbons were likely to be released from sediments over the long term. The submerged prop roots of fringing mangroves in each habitat had a characteristic epibiota. On the open coast, roots were covered with a diverse assemblage of sessile invertebrates and algae. In channels, the most abundant species on roots was the edible oyster Crassostrea virginica ( rhizophorae morph). In streams, the false mussel Mytilopsis sallei covered the most space on roots. Cover of sessile invertebrates was significantly reduced at oiled compared with unoiled sites on the open coast for 4 years after oiling, while oysters and false mussels were reduced in cover at oiled sites in channels and streams through at least 1991, when observations ended. False mussels transplanted from an unoiled stream to oiled and unoiled streams were

Pre-concentration of pesticide residues in environmental water samples using Silica nanoparticles and identification of residues By GC-MS method

OpenAIRE

Tentu. Nageswara Rao; A. Muralidhar Reddy; SNVS. Murthy; Prathipati Revathi; K. Suneel Kumar

2016-01-01

The silica nanoparticles prepared by stober’s mechanism by reaction of tetraethylorthosilicate (TEOS) with ammonia was tested for their adsorption capacity in the pre-concentration of residues of pesticides in water. The synthesized nanoparticles were characterized by Scanning Electron Microscope (SEM), Transmission Electron Microscope (TEM) and X-Ray Diffraction (XRD). The size of the silica nanoparticles were 50 to 250 nm. The solid phase extraction (SPE) cartridges were prepared by filling...

Membranes obtained from alumina from separation water/oil; Membranas obtidas a partir do residuo de alumina para separacao de agua/oleo

Energy Technology Data Exchange (ETDEWEB)

Rosas Neto, M.I.; Lira, H.L; Guimaraes, I.O; Franca, K.B., E-mail: moisesnetu@gmail.com [Universidade Federal de Campina Grande (UFCG), PB, (Brazil)

2016-07-01

This study aims to evaluate by flow test emulsion water/oil a membrane obtained from a crude residue of the alumina industry and see if this membrane is able to filter this emulsion within the limits specified by CONAMA. In this work, tubular membranes composed of the alumina and the residue bentonite clay were produced by extrusion and were sintered at 900, 1000 and 1100 ° C. tangential flow tests were conducted with deionized water and subsequently with an emulsion of water / oil, all done with a pressure of 1.5 bar. The results showed that membranes produced from the crude residue the alumina industry were quite efficient the emulsion's oil removal, reducing the concentration of about 100 ppm in the feed, to below 5ppm and flow rates of around 30L/h.m{sup 2}. (author)

Compositional analysis and projected biofuel potentials from common West African agricultural residues

DEFF Research Database (Denmark)

Thomsen, Sune Tjalfe; Kádár, Zsófia; Schmidt, Jens Ejbye

2014-01-01

In recent years the focus on sustainable biofuel production from agricultural residues has increased considerably. However, the scientific work within this field has predominantly been concentrated upon bioresources from industrialised and newly industrialised countries, while analyses of the res......In recent years the focus on sustainable biofuel production from agricultural residues has increased considerably. However, the scientific work within this field has predominantly been concentrated upon bioresources from industrialised and newly industrialised countries, while analyses......, cassava stalks, plantain peelings, plantain trunks, plantain leaves, cocoa husks, cocoa pods, maize cobs, maize stalks, rice straw, groundnut straw and oil palm empty fruit bunches. The yam peelings showed the highest methane and bioethanol potentials, with 439 L methane (kg Total Solids)−1 and 0.61 L...... bioethanol (kg TS)−1 based on starch and cellulose alone due to their high starch content and low content of un-biodegradable lignin and ash. A complete biomass balance was done for each of the 13 residues, providing a basis for further research into the production of biofuels or biorefining from West...

Predicting the concentration of residual methanol in industrial formalin using machine learning

OpenAIRE

Heidkamp, William

2016-01-01

In this thesis, a machine learning approach was used to develop a predictive model for residual methanol concentration in industrial formalin produced at the Akzo Nobel factory in Kristinehamn, Sweden. The MATLABTM computational environment supplemented with the Statistics and Machine LearningTM toolbox from the MathWorks were used to test various machine learning algorithms on the formalin production data from Akzo Nobel. As a result, the Gaussian Process Regression algorithm was found to pr...

Oxidizing oils, etc. [British patent

Energy Technology Data Exchange (ETDEWEB)

Penniman, W B.D.

1926-03-02

The oxidation of crude petroleum and its distillates, shale oils and tars, waxes, sludges, petroleum residues, asphaltic oils, asphalt, malthas, cracked oils and residues from cracking stills, wood tar oils and wood tar, peat and lignite distillates, coal tar oils and coal tars, and oils containing powdered coal, coke, oreat, sulphur in suspension, by passing air or other oxygen-containing gas through a layer of the material of a depth sufficient substantially to deoxygenate the air and c., is carried out in stages in a series of treatment zones, the pressure in at least one of the zones being above atmospheric pressre. The products of oxidation include acetaldehyde, propionaldehyde, formic, acetic, propionic, butyric, acrylic and phthalic acids, alcohols, acetone, solvents, gums, and substances adapted for use as motor fuels or burnign oils. The oxidizing gas may be enriched with oxygen or be diluted with steam, and its point of entry into the oil and c. layer may be varied to promote or retard settlement of suspended solids.

Advances in biofuel production from oil palm and palm oil processing wastes: A review

Directory of Open Access Journals (Sweden)

Jundika C. Kurnia

2016-03-01

Full Text Available Over the last decades, the palm oil industry has been growing rapidly due to increasing demands for food, cosmetic, and hygienic products. Aside from producing palm oil, the industry generates a huge quantity of residues (dry and wet which can be processed to produce biofuel. Driven by the necessity to find an alternative and renewable energy/fuel resources, numerous technologies have been developed and more are being developed to process oil-palm and palm-oil wastes into biofuel. To further develop these technologies, it is essential to understand the current stage of the industry and technology developments. The objective of this paper is to provide an overview of the palm oil industry, review technologies available to process oil palm and palm oil residues into biofuel, and to summarise the challenges that should be overcome for further development. The paper also discusses the research and development needs, technoeconomics, and life cycle analysis of biofuel production from oil-palm and palm-oil wastes.

Residual concentrations of micropollutants in benthic mussels in the coastal areas of Bohai Sea, North China

International Nuclear Information System (INIS)

Liu Wenxin; Chen Jianglin; Lin Xiumei; Fan Yongsheng; Tao Shu

2007-01-01

Studies of heavy metals and organic pollutants in different benthic mussel species from Bohai Sea show that concentrations of Cd in mussels commonly exceed national biological quality standards. In addition, a site located in Laizhou Bay exhibits higher average concentrations of As, Hg and Pb with respect to the other sites. Residual levels of petroleum hydrocarbons at several sites in Liaodong Bay also exceed quality guidelines. Contents and compositional characteristics of DDT and its metabolites in mussels suggest the probability of recent inputs and potential ecological risks to the local benthic environment. - Residual Cd contents of mussels at many sites in Bohai Sea exceed national marine biological quality standard and compositions of DDT metabolites indicate recent inputs and potential risk

Fuel oil and kerosene sales 1994

International Nuclear Information System (INIS)

1995-01-01

This publication contains the 1994 survey results of the ''Annual Fuel Oil and Kerosene Sales Report'' (Form EIA-821). This is the sixth year that the survey data have appeared in a separate publication. Prior to the 1989 report, the statistics appeared in the Petroleum Marketing Annual (PMA)for reference year 1988 and the Petroleum Marketing Monthly (PMM) for reference years 1984 through 1987. The 1994 edition marks the 11th annual presentation of the results of the ongoing ''Annual Fuel Oil and Kerosene Sales Report'' survey. Distillate and residual fuel oil sales continued to move in opposite directions during 1994. Distillate sales rose for the third year in a row, due to a growing economy. Residual fuel oil sales, on the other hand, declined for the sixth year in a row, due to competitive natural gas prices, and a warmer heating season than in 1993. Distillate fuel oil sales increased 4.4 percent while residual fuel oil sales declined 1.6 percent. Kerosene sales decreased 1.4 percent in 1994

Use of ultrasound in petroleum residue upgradation

Energy Technology Data Exchange (ETDEWEB)

Sawarkar, A.N.; Pandit, A.B.; Samant, S.D.; Joshi, J.B. [Mumbai Univ., Mumbai (India). Inst. of Chemical Technology

2009-06-15

The importance of bottom-of-the barrel upgrading has increased in the current petroleum refining scenario because of the progressively heavier nature of crude oil. Heavy residues contain large concentrations of metals such as vanadium and nickel which foul catalysts and reduce the potential effect of residue fluidized catalytic cracking. This study showed that the cavitational energy induced by ultrasound be be successfully used to upgrade hydrocarbon mixtures. Conventional processes for the upgrading of residual feedstocks, such as thermal cracking and catalytic cracking, were carried out in the temperature range of 400-520 degrees C. Experiments were performed on 2 vacuum residues, Arabian mix vacuum residue (AMVR) and Bombay high vacuum residue (BHVR) and 1 Haldia asphalt (HA). These were subjected to acoustic cavitation for different reaction times from 15 to 120 minutes at ambient temperature and pressure. Two acoustic cavitation devices were compared, namely the ultrasonic bath and ultrasonic horn. In particular, this study compared the ability of these 2 devices to upgrade the petroleum residues to lighter, more value-added products. Different surfactants were used to examine the effect of ultrasound on upgrading the residue when emulsified in water. In order to better understand the reaction mechanism, a kinetic model was developed based on the constituents of the residue. The ultrasonic horn was found to be more effective in bringing about the upgrading than ultrasonic bath. The study also showed that the acoustic cavitation of the aqueous emulsified hydrocarbon mixture could reduce the asphaltenes content to a greater extent than the acoustic cavitation of non-emulsified hydrocarbon mixture. 20 refs., 11 tabs., 17 figs.

The Other Major 2010 Oil Spill: Oil weathering after the Kalamazoo River Dilbit Spill

Science.gov (United States)

Swarthout, B.; Reddy, C. M.; Nelson, R. K.; Hamilton, S. K.; Aeppli, C.; Valentine, D. L.; Fundaun, S. E.; Oliveira, A. H.

2016-02-01

Diluted bitumen (dilbit) from the oil sands (tar sands) of western Canada is increasingly being transported to US markets. North America's largest inland oil spill and the first major oil sands spill in a freshwater environment occurred in 2010, when at least 843,000 gallons leaked from a pipeline into the Kalamazoo River of southwest Michigan. Cleanup of this oil was unusually difficult and protracted, lasting through 2014 and costing over a billion dollars, largely because a substantial fraction of the oil became submersed and deposited in slack water areas over 60 km of river channel, reservoirs, and floodplain backwaters. To investigate the fate of the spilled dilbit from the 2010 Kalamazoo River release, black rings, presumably oil residues, on the bark of dead trees were collected in 2015. These residues were deposited on the trees during high flood levels that have not been observed since the spill and represent an opportunity to constrain weathering processes excluding dissolution. This material contained a major non-GC amenable fraction of 90-95%, presumably oxygenated hydrocarbons. The GC amenable portion was consistent with laboratory weathered dilbit. We used a variety of analytical tools to characterize the dilbit residues, as well as to identify dilbit weathering processes that occurred since the spill.

Residual diesel measurement in sand columns after surfactant/alcohol washing

International Nuclear Information System (INIS)

Martel, R.; Gelinas, P.J.

1996-01-01

A new simple gravimetric technique has been designed to determine residual oil saturation of complex hydrocarbon mixtures (e.g., diesel) in sand column experiments because reliable methods are lacking. The He/N 2 technique is based on drying of sand columns by circulating helium gas to drag oil droplets in a cold trap (liquid nitrogen). With this technique, residual diesel measurement can be performed easily immediately after alcohol/surfactant washing and in the same lab. For high residual diesel content in Ottawa sand (25 to 30 g/kg), the technique is much more accurate (± 2% or 600 mg/kg) than the standard analytical methods for the determination of mineral oil and grease. The average relative error on partial diesel dissolution in sand column estimated after alcohol/surfactant flooding (residual saturation of 10 to 15 g/kg) is as low as 5%. The precision of the He/N 2 technique is adequate to compare relative efficiency of washing solutions when partial extraction of residual oil in Ottawa sand columns is performed. However, this technique is not adapted for determination of traces of oil in sediment or for environmental control of contaminated soils. Each diesel determination by the He/N 2 technique costs less than $8 in chemical products (helium and liquid nitrogen). A simple laboratory drying setup can be built for less than $400 which makes this technique valuable for diesel analyses when a large number of tests are required

CFD (Computational Fluid Dynamics) simulators and thermal cracking of heavy oil and ultraheavy residues using microreactor

Energy Technology Data Exchange (ETDEWEB)

Jardini, Andre L.; Bineli, Aulus R.R.; Viadana, Adriana M.; Maciel, Maria Regina Wolf; Maciel Filho, Rubens [State University of Campinas (UNICAMP), SP (Brazil). School of Chemical Engineering; Medina, Lilian C.; Gomes, Alexandre de O. [PETROBRAS S.A., Rio de Janeiro, RJ (Brazil). Centro de Pesquisas (CENPES); Barros, Ricardo S. [University Foundation Jose Bonifacio (FUJB), Rio de Janeiro, RJ (Brazil)

2008-07-01

In this paper, the design of microreactor with microfluidics channels has been carried out in Computer Aided Design Software (CAD) and constructed in rapid prototyping system to be used in chemical reaction processing of the heavy oil fractions. The flow pattern properties of microreactor (fluid dynamics, mixing behavior) have been considered through CFD (computational fluid dynamics) simulations. CFD calculations are also used to study the design and specification of new microreactor developments. The potential advantages of using a microreactor include better control of reaction conditions, improved safety and portability. A more detailed crude assay of the raw national oil, whose importance was evidenced by PETROBRAS/CENPES allows establishing the optimum strategies and processing conditions, aiming at a maximum utilization of the heavy oil fractions, towards valuable products. These residues are able to be processed in microreactor, in which conventional process like as hydrotreating, catalytic and thermal cracking may be carried out in a much more intensified fashion. The whole process development involves a prior thermal study to define the possible operating conditions for a particular task, the microreactor design through computational fluid dynamics and construction using rapid prototyping. This gives high flexibility for process development, shorter time, and costumer/task oriented process/product development. (author)

Analysis and modelling of the factors controlling seed oil concentration in sunflower: a review

Directory of Open Access Journals (Sweden)

Andrianasolo Fety Nambinina

2016-03-01

Full Text Available Sunflower appears as a potentially highly competitive crop, thanks to the diversification of its market and the richness of its oil. However, seed oil concentration (OC – a commercial criterion for crushing industry – is subjected to genotypic and environmental effects that make it sometimes hardly predictable. It is assumed that more understanding of oil physiology combined with the use of crop models should permit to improve prediction and management of grain quality for various end-users. Main effects of temperature, water, nitrogen, plant density and fungal diseases were reviewed in this paper. Current generic and specific crop models which simulate oil concentration were found to be empirical and to lack of proper evaluation processes. Recently two modeling approaches integrating ecophysiological knowledge were developed by Andrianasolo (2014, Statistical and dynamic modelling of sunflower (Helianthus annuus L. grain composition as a function of agronomic and environmental factors, Ph.D. Thesis, INP Toulouse: (i a statistical approach relating OC to a range of explanatory variables (potential OC, temperature, water and nitrogen stress indices, intercepted radiation, plant density which resulted in prediction quality from 1.9 to 2.5 oil points depending on the nature of the models; (ii a dynamic approach, based on “source-sink” relationships involving leaves, stems, receptacles (as sources and hulls, proteins and oil (as sinks and using priority rules for carbon and nitrogen allocation. The latter model reproduced dynamic patterns of all source and sink components faithfully, but tended to overestimate OC. A better description of photosynthesis and nitrogen uptake, as well as genotypic parameters is expected to improve its performance.

Innovation on Street Food Products (Instant Porridge and Cookies Based on Fortified Patin Fish Protein Concentrate with Red Palm Oil and Encaptulated Oil Fish

Directory of Open Access Journals (Sweden)

Dewita Dewita

2015-02-01

Full Text Available This research aimed to establish innovation on street food (instant porridge and cookiesfrom Patin Fish Protein Concentrate fortified by blending red palm oil and encaptulated patinfish’s oil. The Encaptulation was conducted by blending of red palm oil and patin fish’s oil usingspray dryer. The blending was consisted of three combinations namely 50 : 50 (A1, 40 : 60 (A2and 60 : 40 (A3 for ratio between red palm oil and patin fish’s oil. The best combination’s resultswas fortified into street food (instant porridge and cookies. The blending was tested by measureyield, fat and fatty acid profile. Moreover, organoleptics and proximate tests were carrie out for thebest treatment of blending in instant porridge and cookies. The results show that encaptulatedyield reached 55 % that rise from A1 treatment as the best treatment with fat content of 17.26%.Profile of unsaturated fatty acid especially fatty acid omega 9 from blending fish oil and palm oilwas 59.29%. The number of fatty acid omega 9 was higher than saturated fatty acid which was18.56%. Furthermore, based on organoleptic tests of instant porridge and cookies using under fiveyear children respondents, it was proven that 93% of children was like the products. Proximate analysis of instant porridge revealed that protein content was 11.04 %, water content was 5.03%,fat content was 1.92 % and ash was 0.64 %. However, proximate analysis showed that cookiesowned protein of 9.11%, fat of 17.03% , water content was 3.93% and ash of 1.38%.Keywords : Encaptulated fish, street food, patin fish protein concentrate, palm oil

Nanofluid of graphene-based amphiphilic Janus nanosheets for tertiary or enhanced oil recovery: High performance at low concentration.

Science.gov (United States)

Luo, Dan; Wang, Feng; Zhu, Jingyi; Cao, Feng; Liu, Yuan; Li, Xiaogang; Willson, Richard C; Yang, Zhaozhong; Chu, Ching-Wu; Ren, Zhifeng

2016-07-12

The current simple nanofluid flooding method for tertiary or enhanced oil recovery is inefficient, especially when used with low nanoparticle concentration. We have designed and produced a nanofluid of graphene-based amphiphilic nanosheets that is very effective at low concentration. Our nanosheets spontaneously approached the oil-water interface and reduced the interfacial tension in a saline environment (4 wt % NaCl and 1 wt % CaCl2), regardless of the solid surface wettability. A climbing film appeared and grew at moderate hydrodynamic condition to encapsulate the oil phase. With strong hydrodynamic power input, a solid-like interfacial film formed and was able to return to its original form even after being seriously disturbed. The film rapidly separated oil and water phases for slug-like oil displacement. The unique behavior of our nanosheet nanofluid tripled the best performance of conventional nanofluid flooding methods under similar conditions.

Cannabinoids concentration variability in cannabis olive oil galenic preparations.

Science.gov (United States)

Carcieri, Chiara; Tomasello, Cristina; Simiele, Marco; De Nicolò, Amedeo; Avataneo, Valeria; Canzoneri, Luca; Cusato, Jessica; Di Perri, Giovanni; D'Avolio, Antonio

2018-01-01

Knowledge of the exact concentration of active compounds in galenic preparations is crucial to be able to ensure their quality and to properly administer the prescribed dose. Currently, the need for titration of extracts is still debated. Considering this, together with the absence of a standard preparation method, the aim of this study was to evaluate cannabinoids concentrations variability in galenic olive oil extracts, to evaluate the interlot and interlaboratory variability in the extraction yield and in the preparation composition. Two hundred and one extracts (123 (61.2%) from Bedrocan ® , 54 (26.9%) from Bediol ® , 11 (5.5%) from Bedrolite ® , and 13 (6.5%) from mixed preparations) were analysed by liquid chromatography coupled with tandem mass spectrometry, quantifying cannabinoids (THC, CBD, THCA, CBDA and CBN) concentrations. The RSD% of THC and CBD concentrations resulted higher than 50%. Specifically for Bedrocan ® , Bediol ® , Bedrolite ® (5 g/50 ml), these were THC 82%, THC 53% and CBD 91%, THC 58% and CBD 59%, respectively. The median extraction yields were greater than 75% for all preparations. Our results highlighted a wide variability in THC and CBD concentrations that justify the need for titration and opens further questions about other pharmaceutical preparations without regulatory indication for this procedure. © 2017 Royal Pharmaceutical Society.

Catalytic copyrolysis of cork oak and bio-oil distillation residue

Science.gov (United States)

Lee, Yejin; Oh, Daejun; Kim, Young-Min; Jae, Jungho; Jung, Sang-Chul; Jeon, Jong-Ki; Kim, Sang Chai; Park, Young-Kwon

2018-01-01

The atmospheric distillation residue (ADR) of cork oak (CO) pyrolysis oil was used as the co-feeding material for the catalytic pyrolysis of CO over HZSM-5 catalysts to improve the formation of aromatic hydrocarbons. Although the non-catalytic copyrolysis of CO and ADR did not improve the formation of aromatic hydrocarbons, the catalytic copyrolysis of CO and ADR promoted the synergistic formation of aromatic hydrocarbons. HZSM-5(30), having a lower SiO2/Al2O3(30), showed better performance for the formation of aromatic hydrocarbons than HZSM-5(80) because of its higher acidity. The catalytic copyrolysis of CO and ADR also decreased the formation of coke. The largest quantity of aromatic hydrocarbons was obtained from the catalytic copyrolysis of CO and ADR over HZSM-5 (30) at 600 °C, whereas the lowest coke yield was achieved at 700 °C. When the catalyst to sample ratio was increased from 2:1 to 5:1, the synergistic formation of aromatic hydrocarbons was limited, resulting in a lower experimental yield of aromatic hydrocarbons than the theoretical yield. A lower coke yield was also achieved at a high catalyst to sample ratio (5:1).

Soy Sauce Residue Oil Extracted by a Novel Continuous Phase Transition Extraction under Low Temperature and Its Refining Process.

Science.gov (United States)

Zhao, Lichao; Zhang, Yong; He, Liping; Dai, Weijie; Lai, Yingyi; Yao, Xueyi; Cao, Yong

2014-04-09

On the basis of previous single-factor experiments, extraction parameters of soy sauce residue (SSR) oil extracted using a self-developed continuous phase transition extraction method at low temperature was optimized using the response surface methodology. The established optimal conditions for maximum oil yield were n-butane solvent, 0.5 MPa extraction pressure, 45 °C temperature, 62 min extraction time, and 45 mesh raw material granularity. Under these conditions, the actual yield was 28.43% ± 0.17%, which is relatively close to the predicted yield. Meanwhile, isoflavone was extracted from defatted SSR using the same method, but the parameters and solvent used were altered. The new solvent was 95% (v/v) ethanol, and extraction was performed under 1.0 MPa at 60 °C for 90 min. The extracted isoflavones, with 0.18% ± 0.012% yield, mainly comprised daidzein and genistein, two kinds of aglycones. The novel continuous phase transition extraction under low temperature could provide favorable conditions for the extraction of nonpolar or strongly polar substances. The oil physicochemical properties and fatty acids compositions were analyzed. Results showed that the main drawback of the crude oil was the excess of acid value (AV, 63.9 ± 0.1 mg KOH/g) and peroxide value (POV, 9.05 ± 0.3 mmol/kg), compared with that of normal soybean oil. However, through molecular distillation, AV and POV dropped to 1.78 ± 0.12 mg KOH/g and 5.9 ± 0.08 mmol/kg, respectively. This refined oil may be used as feedstuff oil.

Catalytic oxidation of concentrated orange oil phase by synthetic metallic complexes biomimetic to MMO enzyme.

Science.gov (United States)

Fernandes, Ilizandra A; Esmelindro, Maria Carolina; Corazza, Marcos L; Franceschi, Elton; Treichel, Helen; de Oliveira, Debora; Frizzo, Caren D; Oliveira, J Vladimir

2010-07-01

This paper reports the catalytic oxidation of the concentrated orange oil phase using the complexes [Fe(III)(BMPP)Cl(micro-O)Fe(III)Cl(3)], [Cu(II)(BTMEA)(2)Cl]Cl and [Co(II)(BMPP)]Cl(2) biomimetic to methane monooxygenase enzyme as catalysts and hydrogen peroxide as oxidant. The reaction products of oil oxidation, mainly nootkatone, were identified by gas chromatography/mass spectrometry. A screening of catalysts was performed through a full 2(3) experimental design, varying the temperature from 30 to 70 degrees C, the catalyst concentration from 7.0 x 10(-4) to 1.5 x 10(-3) mol L(-1) and the oxidant/substrate molar ratio from 1:1 to 3:1. The results of reaction kinetics employing the most promising catalysts showed that conversions to nootkatone of up to 8% were achieved after 16 h at 70 degrees C. The results obtained in this study in terms of nootkatone production should be considered encouraging, since a real, industrially collected, raw material, instead of pure valencene, was employed in the reaction experiments, with a final content about ten times that present in the original concentrated oil.

Influence of phosphorus content of coconut oil on deposit and performance of plant oil pressure stoves

Energy Technology Data Exchange (ETDEWEB)

Kratzeisen, M.; Mueller, J. [Institut fuer Agrartechnik, Universitaet Hohenheim (440e), Garbenstrasse 9, D-70593 Stuttgart (Germany)

2010-11-15

Influence of phosphorus lipids on formation of deposits and performance of plant oil pressure stoves was investigated. Refined coconut oil with an original phosphorous content of 5.9 mg/kg was used as base for fuel blends by adding lecithin to adjust increased phosphorous concentrations of 32.2, 51.6 and 63.0 mg/kg. The fuel blends were analysed for acid value, iodine value, total contamination, ash content and Conradson carbon residue according to standard methods. In burning trials, the specific fuel consumption, the required frequency of nozzle cleaning and the amount of deposits in the vaporizer were measured. Results showed an exponential increase of deposits in the vaporizer when phosphorous content was increased: deposits amounted to 0.12 g/kg of consumed fuel for unblended coconut oil and 0.92 g/kg for the blend with the highest phosphorous content. Furthermore, increased phosphorous content caused higher fuel consumption of 0.375 kg/h compared to 0.316 kg/h for the control. (author)

Spray dried microparticles of chia oil using emulsion stabilized by whey protein concentrate and pectin by electrostatic deposition.

Science.gov (United States)

Noello, C; Carvalho, A G S; Silva, V M; Hubinger, M D

2016-11-01

Chia seed oil has a high content of α-linolenic acid (60%) and linoleic acid (20%). Use of this oil in different products is limited due to its liquid state, and the presence of insaturation is a trigger for oxidation. In this context, to facilitate the incorporation of chia oil in food products and increase its protection against oxidation, the aim of this work was to produce chia oil microparticles by spray drying using emulsions stabilized by whey protein concentrate (ζ-potential +13.4 at pH3.8) and pectin (ζ-potential -40.4 at pH3.8) through the electrostatic layer-by-layer deposition technique and emulsions prepared with only whey protein concentrate. Emulsions stabilized by whey protein concentrate and stabilized by whey protein concentrate-pectin were prepared using maltodextrin (10 DE) and modified starch (Hi-Cap® 100). They were characterized in relation to stability, droplet size, ζ-Potential and optical microscopy. The microparticles were characterized in relation to moisture content, water activity, particle size, microstructure and oxidative stability by the Rancimat method. Emulsions stabilized by whey protein concentrate-pectin with added maltodextrin 10 DE and emulsions stabilized by whey protein concentrate with added modified starch (Hi-Cap® 100) were stable after 24h. Emulsions stabilized by whey protein concentrate and by whey protein concentrate-pectin showed droplets with mean diameter ranging from 0.80 to 1.31μm, respectively and ζ-potential varying from -6.9 to -27.43mV, respectively. After spray drying, the microparticles showed an mean diameter ranging from 7.00 to 9.00μm. All samples presented high encapsulation efficiency values, above 99%. Microparticles produced with modified starch showed a smoother spherical surface than particles with maltodextrin 10 DE, which presented a wrinkled surface. All microparticles exhibited higher oxidative stability than chia oil in pure form. Copyright © 2016 Elsevier Ltd. All rights reserved.

Concentration of eicosapentaenoic acid (EPA and docosahexaenoic acid (DHA of Asian catfish oil by urea complexation: optimization of reaction conditions

Directory of Open Access Journals (Sweden)

Pornpisanu Thammapat

2016-04-01

Full Text Available Optimization of the concentrating conditions of eicosapentaenoic acid (EPA and docosahexaenoic acid (DHA extracted from Asian catfish oil was studied to obtain a maximum concentration. The crude fish oil was extracted from the belly flap and adipose tissue of Asian catfish, and the extracted oil was used as fresh crude oil. The EPA and DHA were concentrated by the urea complexation method. A hexagonal rotatable design was applied to examine the effects of crystallization temperature and urea-to-fatty acid ratio on the total content of EPA and DHA (Y1 and the liquid recovery yield (Y2 . The second order polynomial regression models for Y1 and Y2 were employed to generate the response surfaces. Under the optimum conditions of -20 °C and a urea-to-fatty acid ratio of 4 (w/w, the total concentration of EPA and DHA could be increased by up to 88%, while a liquid recovery yield of 26% was obtained.

Origin of oil shale

Energy Technology Data Exchange (ETDEWEB)

Cunningham-Craig, E H

1915-01-01

Kerogen was believed to be formed by the inspissation of petroleum. During this process nitrogen and sulfur compounds were concentrated in the most inspissated or weathered products. At a certain stage, reached gradually, the organic matter became insoluble in carbon-disulfide and ceased to be a bitumen. Oil shale was formed by the power of certain clays or shales to absorb inspissated petroleum, particularly unsaturated hydrocarbons. This adsorption apparently depended on the colloid content of the argillaceous rock. This rock retained these impregnated petroleum residues long after porous sandstones in the vicinity had lost all traces of petroleum by weathering and leaching.

Sulfur compounds and species in Russian residues by XPS and PY-GC-PFPO

Energy Technology Data Exchange (ETDEWEB)

Quan, S.; Suoqi, Z.; Chunming, X. [University of Petroleum, State Key Laboraory of Heavy Oil Processing, Beijing (China); Kotlyar, L.; Kung, J. [National Research Council of Canada, Institute for Chemical processand Environmental Technology, Ottawa, ON (Canada); Chung, K. H. [Syncrude Canada Limited, Edmonton, AB (Canada)

2004-07-01

Distribution and structure of sulfur components of Russian crude oil were investigated by separating vacuum residues from the oil into 17 narrow cuts and one end-cut using the supercritical fluid extraction and fractionation technique (SFEF). The cuts were analyzed by gas chromatography, with conditions optimized from 600 degrees C to 1,000 degrees C, and between two and twenty seconds. In general, the total amount of of the sulfur compounds in pyrolizates was found to be proportional to the sulfur content in the vacuum residues. Thiophenes, benzothiophenes and dibenzothiophene content varied from vacuum residue to vacuum residue. Benzothiophens were identified as the dominant sulfur compounds in the pyrolizate of Russian crude oil.

1D Simulations for Microbial Enhanced Oil Recovery with Metabolite Partitioning

DEFF Research Database (Denmark)

Nielsen, Sidsel Marie; Shapiro, Alexander; Michelsen, Michael Locht

2010-01-01

We have developed a mathematical model describing the process of microbial enhanced oil recovery (MEOR). The one-dimensional isothermal model comprises displacement of oil bywater containing bacteria and substrate for their feeding. The bacterial products are both bacteria andmetabolites....... The characteristics for the water phase saturation profiles and the oil recovery curves are elucidated. However, the effect from the surfactant is not necessarily restricted to influence only interfacial tension, but it can also be an approach for changing, e.g., wettability. The distribution coefficient determines...... the time lag, until residual oil mobilization is initialized. It has also been found that the final recovery depends on the distance from the inlet before the surfactant effect takes place. The surfactant effect position is sensitive to changes in maximum growth rate, and injection concentrations...

A method for assessing residual NAPL based on organic chemical concentrations in soil samples

International Nuclear Information System (INIS)

Feenstra, S.; Mackay, D.M.; Cherry, J.A.

1991-01-01

Ground water contamination by non-aqueous phase liquid (NAPL) chemicals is a serious concern at many industrial facilities and waste disposal sites. NAPL in the form of immobile residual contamination, or pools of mobile or potentially mobile NAPL, can represent continuing sources of ground water contamination. In order to develop rational and cost-effective plans for remediation of soil and ground water contamination at such sites, it is essential to determine if non-aqueous phase liquid (NAPL) chemicals are present in the subsurface and delineate the zones of NAPL contamination. Qualitatively, soil analyses that exhibit chemical concentrations in the percent range or >10,000 mg/kg would generally be considered to indicate the presence of NAPL. However, the results of soil analyses are seldom used in a quantitative manner to assess the possible presence of residual NAPL contamination when chemical concentrations are lower and the presence of NAPL is not obvious. The assessment of the presence of NAPL in soil samples is possible using the results of chemical and physical analyses of the soil, and the fundamental principles of chemical partitioning in unsaturated or saturated soil. The method requires information on the soil of the type typically considered in ground water contamination studies and provides a simple tool for the investigators of chemical spill and waste disposal sites to assess whether soil chemical analyses indicate the presence of residual NAPL in the subsurface

Steam injection and enhanced bioremediation of heavy fuel oil contamination

International Nuclear Information System (INIS)

Dablow, J.; Hicks, R.; Cacciatore, D.

1995-01-01

Steam injection has been shown to be successful in remediating sites impacted by heavy fuel oils. Field demonstrations at both pilot and full scale have removed No. 2 diesel fuel and Navy Special Fuel Oil (No. 5 fuel oil) from impacted soils. Removal mechanisms include enhanced volatilization of vapor- and adsorbed-phase contaminants and enhanced mobility due to decreased viscosity and associated residual saturation of separate- and adsorbed-phase contaminants. Laboratory studies have shown that indigenous biologic populations are significantly reduced, but are not eliminated by steam injection operations. Populations were readily reestablished by augmentation with nutrients. This suggests that biodegradation enhanced by warm, moist, oxygenated environments can be expected to further reduce concentrations of contaminants following cessation of steam injection operations

Theory and application of landfarming to remediate polycyclic aromatic hydrocarbons and mineral oil-contaminated sediments: beneficial reuse

NARCIS (Netherlands)

Harmsen, J.; Rulkens, W.H.; Sims, R.C.; Rijtema, P.E.; Zweers, A.J.

2007-01-01

When applying landfarming for the remediation of contaminated soil and sediment, a fraction of the soil-bound contaminant is rapidly degraded; however, a residual concentration may remain, which slowly degrades. Degradation of polycyclic aromatic hydrocarbons (PAHs) and mineral oil can be described

Processing of oil products using complex radiation-thermal treatment and radiation oxonolysis

International Nuclear Information System (INIS)

Zaikin, Yu.A.; Zaikina, R.F.

2002-01-01

compound due to disintegration of condensed polyarene nuclei included in molecules of pitches and asphaltenes. It also leads to considerable decrease in the mean molecular mass of the residue, elimination of the part of sulfur and nitrogen atoms, and enrichment of the heavy residue by oxygen. At the same time the degree of hydrogen deficiency becomes lower due to the opening of the part of aromatic rings. Splitting of pyrrol and thiophene cycles diminishes sulfur contents and simultaneously causes a rise in oxygen concentration. Data of infra-red spectroscopy confirm that radiation oxonolysis in the bubbling mode causes disintegration of aromatic nuclei and oxidation of sulfuric compounds. The results obtained open new opportunities for upgrading high-viscous oils and raising their potential fuel yields due to higher commercial validity of heavy residue after combined radiation-thermal processing and oxonolysis

[Identification of spill oil species based on low concentration synchronous fluorescence spectra and RBF neural network].

Science.gov (United States)

Liu, Qian-qian; Wang, Chun-yan; Shi, Xiao-feng; Li, Wen-dong; Luan, Xiao-ning; Hou, Shi-lin; Zhang, Jin-liang; Zheng, Rong-er

2012-04-01

In this paper, a new method was developed to differentiate the spill oil samples. The synchronous fluorescence spectra in the lower nonlinear concentration range of 10(-2) - 10(-1) g x L(-1) were collected to get training data base. Radial basis function artificial neural network (RBF-ANN) was used to identify the samples sets, along with principal component analysis (PCA) as the feature extraction method. The recognition rate of the closely-related oil source samples is 92%. All the results demonstrated that the proposed method could identify the crude oil samples effectively by just one synchronous spectrum of the spill oil sample. The method was supposed to be very suitable to the real-time spill oil identification, and can also be easily applied to the oil logging and the analysis of other multi-PAHs or multi-fluorescent mixtures.

Partial least squares modeling of combined infrared, 1H NMR and 13C NMR spectra to predict long residue properties of crude oils

NARCIS (Netherlands)

de Peinder, P.; Visser, T.; Petrauskas, D.D.; Salvatori, F.; Soulimani, F.; Weckhuysen, B.M.

2009-01-01

Research has been carried out to determine the potential of partial least squares (PLS) modeling of mid-infrared (IR) spectra of crude oils combined with the corresponding 1H and 13C nuclear magnetic resonance (NMR) data, to predict the long residue (LR) properties of these substances. The study

Metagenome enrichment approach used for selection of oil-degrading bacteria consortia for drill cutting residue bioremediation.

Science.gov (United States)

Guerra, Alaine B; Oliveira, Jorge S; Silva-Portela, Rita C B; Araújo, Wydemberg; Carlos, Aline C; Vasconcelos, Ana Tereza R; Freitas, Ana Teresa; Domingos, Yldeney Silva; de Farias, Mirna Ferreira; Fernandes, Glauber José Turolla; Agnez-Lima, Lucymara F

2018-04-01

Drill cuttings leave behind thousands of tons of residues without adequate treatment, generating a large environmental liability. Therefore knowledge about the microbial community of drilling residue may be useful for developing bioremediation strategies. In this work, samples of drilling residue were enriched in different culture media in the presence of petroleum, aiming to select potentially oil-degrading bacteria and biosurfactant producers. Total DNA was extracted directly from the drill cutting samples and from two enriched consortia and sequenced using the Ion Torrent platform. Taxonomic analysis revealed the predominance of Proteobacteria in the metagenome from the drill cuttings, while Firmicutes was enriched in consortia samples. Functional analysis using the Biosurfactants and Biodegradation Database (BioSurfDB) revealed a similar pattern among the three samples regarding hydrocarbon degradation and biosurfactants production pathways. However, some statistical differences were observed between samples. Namely, the pathways related to the degradation of fatty acids, chloroalkanes, and chloroalkanes were enriched in consortia samples. The degradation colorimetric assay using dichlorophenolindophenol as an indicator was positive for several hydrocarbon substrates. The consortia were also able to produce biosurfactants, with biosynthesis of iturin, lichnysin, and surfactin among the more abundant pathways. A microcosms assay followed by gas chromatography analysis showed the efficacy of the consortia in degrading alkanes, as we observed a reduction of around 66% and 30% for each consortium in total alkanes. These data suggest the potential use of these consortia in the bioremediation of drilling residue based on autochthonous bioaugmentation. Copyright © 2018 Elsevier Ltd. All rights reserved.

High hole mobility p-type GaN with low residual hydrogen concentration prepared by pulsed sputtering

Science.gov (United States)

Arakawa, Yasuaki; Ueno, Kohei; Kobayashi, Atsushi; Ohta, Jitsuo; Fujioka, Hiroshi

2016-08-01

We have grown Mg-doped GaN films with low residual hydrogen concentration using a low-temperature pulsed sputtering deposition (PSD) process. The growth system is inherently hydrogen-free, allowing us to obtain high-purity Mg-doped GaN films with residual hydrogen concentrations below 5 × 1016 cm-3, which is the detection limit of secondary ion mass spectroscopy. In the Mg profile, no memory effect or serious dopant diffusion was detected. The as-deposited Mg-doped GaN films showed clear p-type conductivity at room temperature (RT) without thermal activation. The GaN film doped with a low concentration of Mg (7.9 × 1017 cm-3) deposited by PSD showed hole mobilities of 34 and 62 cm2 V-1 s-1 at RT and 175 K, respectively, which are as high as those of films grown by a state-of-the-art metal-organic chemical vapor deposition apparatus. These results indicate that PSD is a powerful tool for the fabrication of GaN-based vertical power devices.

Thermochemical recycling of mixture of scrap tyres and waste lubricating oil into high caloric value products

International Nuclear Information System (INIS)

Abdul-Raouf, Manar E.; Maysour, Nermine E.; Abdul-Azim, Abdul-Azim A.; Amin, Mahasen S.

2010-01-01

Scrap tyres and used lubricating oils represent together growing environmental problem because they are not biodegradable and their components cannot readily be recovered. In the present investigation, the thermochemical recycling of mixture of old tyres with waste lubricating oil by pyrolysis and the value of the products obtained have been studied. First, thermobalance experiments were carried out, studying the influence of the following variables: temperature, type of catalyst and catalyst concentration on the pyrolysis reaction of a mixture of 1/1 wt./wt. oil/tyre ratio. These thermobalance results were thoroughly investigated to study the effect of the main process variables on yields of derived products: oils, gases and solid residue.

Development of Microorganisms with Improved Transport and Biosurfactant Activity for Enhanced Oil Recovery

Energy Technology Data Exchange (ETDEWEB)

M.J. McInerney; K.E. Duncan; N. Youssef; T. Fincher; S.K. Maudgalya; M.J. Folmsbee; R. Knapp; Randy R. Simpson; N.Ravi; D. Nagle

2005-08-15

The project had three objectives: (1) to develop microbial strains with improved biosurfactant properties that use cost-effective nutrients, (2) to obtain biosurfactant strains with improved transport properties through sandstones, and (3) to determine the empirical relationship between surfactant concentration and interfacial tension and whether in situ reactions kinetics and biosurfactant concentration meets appropriate engineering design criteria. Here, we show that a lipopeptide biosurfactant produced by Bacillus mojavensis strain JF-2 mobilized substantial amounts of residual hydrocarbon from sand-packed columns and Berea sandstone cores when a viscosifying agent and a low molecular weight alcohol were present. The amount of residual hydrocarbon mobilized depended on the biosurfactant concentration. Tertiary oil recovery experiments showed that 10 to 40 mg/l of JF-2 biosurfactant in the presence of 0.1 mM 2,3-butanediol and 1 g/l of partially hydrolyzed polyacrylamide (PHPA) recovered 10-40% of residual oil from Berea sandstone cores. Even low biosurfactant concentrations (16 mg/l) mobilized substantial amounts of residual hydrocarbon (29%). The bio-surfactant lowered IFT by nearly 2 orders of magnitude compared to typical IFT values of 28-29 mN/m. Increasing the salinity increased the IFT with or without 2,3-butanediol present. The lowest interfacial tension observed was 0.1 mN/m. A mathematical model that relates oil recovery to biosurfactant concentration was modified to include the stepwise changes in IFT as biosurfactant concentrations changes. This model adequately predicted the experimentally observed changes in IFT as a function of biosurfactant concentration. Theses data show that lipopeptide biosurfactant systems may be effective in removing hydrocarbon contamination sources in soils and aquifers and for the recovery of entrapped oil from low production oil reservoirs. Diverse microorganisms were screened for biosurfactant production and anaerobic

An evaluation of bioremediation of oiled sediments buried within a mudflat environment

International Nuclear Information System (INIS)

Swannell, R. P. J.; Mitchell, D. J.; Jones, D. M.; Willis, A. L.; Lee, K.

1997-01-01

An investigation was carried out to determine the potential of bioremediation to treat an oil-contaminated shoreline sediment in the southwest of England. The specific objective was to determine whether periodic additions of inorganic nitrate and phosphate could be used to enhance the biodegradation rate of weathered and emulsified Arabian Light crude oil-contaminated sediment stranded on the beach at a depth of about 15 cm. To measure the potential for successful treatment, changes in the chemical composition and concentration of residual hydrocarbons, microbial carbon dioxide production rates in situ and in the hydrocarbon-degrading microbial community, were monitored. Results showed that regular additions of inorganic nutrients significantly enhanced the rate of oil biodegradation in comparison with unfertilized oil sediments, indicating that bioremediation could be successful in treating buried oil in aerobic fine sediments.17 refs., 4 tabs., 4 figs

Use of Plackett-Burman design for rapid screening of nitrogen and carbon sources for the production of lipase in solid state fermentation by Yarrowia lipolytica from mustard oil cake (Brassica napus

Directory of Open Access Journals (Sweden)

Sarat Babu Imandi

2013-09-01

Full Text Available Mustard oil cake (Brassica napus, the residue obtained after extraction of mustard oil from mustard oil seeds, was investigated for the production of lipase under solid state fermentation (SSF using the marine yeast Yarrowia lipolytica NCIM 3589. Process parameters such as incubation time, biomass concentration, initial moisture content, carbon source concentration and nitrogen source concentration of the medium were optimized. Screening of ten nitrogen and five carbon sources has been accomplished with the help of Plackett-Burman design. The highest lipase activity of 57.89 units per gram of dry fermented substrate (U/gds was observed with the substrate of mustard oil cake in four days of fermentation.

Analysis of heavy oils: Method development and application to Cerro Negro heavy petroleum

Energy Technology Data Exchange (ETDEWEB)

None

1989-12-01

On March 6, 1980, the US Department of Energy (DOE) and the Ministry of Energy and Mines of Venezuela (MEMV) entered into a joint agreement which included analysis of heavy crude oils from the Venezuelan Orinoco oil belt. The purpose of this report is to present compositional data and describe new analytical methods obtained from work on the Cerro Negro Orinoco belt crude oil since 1980. Most of the chapters focus on the methods rather than the resulting data on Cerro Negro oil, and results from other oils obtained during the verification of the method are included. In addition, published work on analysis of heavy oils, tar sand bitumens, and like materials is reviewed, and the overall state of the art in analytical methodology for heavy fossil liquids is assessed. The various phases of the work included: distillation and determination of routine'' physical/chemical properties (Chapter 1); preliminary separation of >200{degrees} C distillates and the residue into acid, base, neutral, saturated hydrocarbon and neutral-aromatic concentrates (Chapter 2); further separation of acid, base, and neutral concentrates into subtypes (Chapters 3--5); and determination of the distribution of metal-containing compounds in all fractions (Chapter 6).

Analysis of heavy oils: Method development and application to Cerro Negro heavy petroleum

Energy Technology Data Exchange (ETDEWEB)

Carbognani, L.; Hazos, M.; Sanchez, V. (INTEVEP, Filial de Petroleos de Venezuela, SA, Caracas (Venezuela)); Green, J.A.; Green, J.B.; Grigsby, R.D.; Pearson, C.D.; Reynolds, J.W.; Shay, J.Y.; Sturm, G.P. Jr.; Thomson, J.S.; Vogh, J.W.; Vrana, R.P.; Yu, S.K.T.; Diehl, B.H.; Grizzle, P.L.; Hirsch, D.E; Hornung, K.W.; Tang, S.Y.

1989-12-01

On March 6, 1980, the US Department of Energy (DOE) and the Ministry of Energy and Mines of Venezuela (MEMV) entered into a joint agreement which included analysis of heavy crude oils from the Venezuelan Orinoco oil belt.The purpose of this report is to present compositional data and describe new analytical methods obtained from work on the Cerro Negro Orinoco belt crude oil since 1980. Most of the chapters focus on the methods rather than the resulting data on Cerro Negro oil, and results from other oils obtained during the verification of the method are included. In addition, published work on analysis of heavy oils, tar sand bitumens, and like materials is reviewed, and the overall state of the art in analytical methodology for heavy fossil liquids is assessed. The various phases of the work included: distillation and determination of routine'' physical/chemical properties (Chapter 1); preliminary separation of >200{degree}C distillates and the residue into acid, base, neutral, saturated hydrocarbon and neutral-aromatic concentrates (Chapter 2); further separation of acid, base, and neutral concentrates into subtypes (Chapters 3-5); and determination of the distribution of metal-containing compounds in all fractions (Chapter 6).

Fifth DOE symposium on enhanced oil and gas recovery and improved drilling technology. Volume 2. Oil

Energy Technology Data Exchange (ETDEWEB)

Linville, B. [ed.

1979-01-01

Volume 2 contains papers from the following sessions: residual oil determination; thermal methods; heavy oil-tar sands; technology transfer; and carbon dioxide flooding. Individual papers were processed.

Separation of oil and grease from oil sludge using surfactant

International Nuclear Information System (INIS)

Ainon Abdul Aziz; Syed Hakimi Sakuma Syed Ahmad; Zalina Laili

2005-01-01

The objective of the experiments was to observe the efficiency of the surfactant to remove oil and grease from oil sludges using various surfactant concentration ranging from 10 %, 15 %, 20 % and 30 %. The surfactant solution consists of two mixtures of Aqua 2000 and D Bond. The oil sludge were subjected to heating and surfactant treatment process. Remaining oil and grease concentration were observed on the oil sludges after treatment. Small scale experiments were conducted by heating process, without heating process and heating process with addition of sodium chloride. Surfactant solution was added in each process. Results shows that there is separation of oil and grease from the oil sludges. There were formation of mini emulsions (oil in water). The higher the concentration of surfactant used, the higher the concentrations of mini emulsion formed as observed. Solid remains after the treatment process were found to contain lesser oil concentration with presence of bitumen, sediment, organic and inorganic materials. After a washing process using distilled water, the solid was still black but less oily than before the treatment. There is no separation of oil occurred in aqueous solution for the control experiment. (Author)

Super oil cracking update

International Nuclear Information System (INIS)

Mulraney, D.

1997-01-01

The conversion of residual fuel oil to usable middle distillates was discussed. The residue conversion processing paths are usually based on separation, carbon rejection, or hydrogen addition principles. Super Oil Cracking (SOC) uses a slurry catalyst system in a new, tubular reactor to achieve high levels of hydrothermal conversion. SOC can upgrade a variety of heavy, high metals residue feedstocks with high yields of middle distillates. The SOC products can also be further treated into feedstocks for FCC or hydrocracking. The SOC process can be incorporated easily into a refinery to obtain incremental residue conversion directly. It can also be integrated with other residue processes, acting as a demetallization and decarbonization step which results in enhanced overall conversion. The relative rate of coke formation and its handling are distinguishing characteristics between residue upgrading technologies. The SOC process operates at higher temperatures that other residue hydrocracking processes resulting in higher rates of thermal decomposition, thus preventing coke formation. SOC process can operate as a stand-alone upgrader or can be integrated with other bottoms processing steps to extend the refiner's range of options for increasing bottoms conversion.3 tabs., 14 figs

Atmospheric BTEX concentrations in the vicinity of the crude oil refinery of the Baltic region.

Science.gov (United States)

Baltrėnas, Pranas; Baltrėnaitė, Edita; Serevičienė, Vaida; Pereira, Paulo

2011-11-01

Among chemical industries, petroleum refineries have been identified as large emitters of a wide variety of pollutants. Benzene, toluene, ethylbenzene, and xylene (BTEX) form an important group of aromatic volatile organic compounds (VOCs) because of their role in the troposphere chemistry and the risk posed to human health. A very large crude oil refinery of the Baltic States (200,000 bbl/day) is situated in the northern, rural part of Lithuania, 10 km from the town of Mažeikiai (Lithuania). The objectives of this study were: (1) to determine of atmospheric levels of BTEX in the region rural and urban parts at the vicinity of the crude oil refinery; and (2) to investigate the effect of meteorological parameters (wind speed, wind direction, temperature, pressure, humidity) on the concentrations measured. The averaged concentration of benzene varied from 2.12 ppbv in the rural areas to 2.75 ppbv in the urban areas where the traffic was determined to be a dominant source of BTEX emissions. Our study showed that concentration of benzene, as strictly regulated air pollutant by EU Directive 2008/50/EC, did not exceed the limit of 5 ppbv in the region in the vicinity of the crude oil refinery during the investigated period. No significant change in air quality in the vicinity of the oil refinery was discovered, however, an impact of the industry on the background air quality was detected. The T/B ratio (0.50-0.81) that was much lower than 2.0, identified other sources of pollution than traffic.

Charred olive stones: experimental and archaeological evidence for recognizing olive processing residues used as fuel

NARCIS (Netherlands)

Braadbaart, Freek; Marinova, E.; Sarpaki, A.

After extracting oil from olives a residue is left usually referred to as the olive oil processing residue (OPR). This study explores the way in which ancient societies may have used OPR as fuel for fires to generate heat and the various issues that are related to the residues of this fuel. After

Characterization of hams added with nut residual pastes from the mechanical extraction of oil

Directory of Open Access Journals (Sweden)

Juan José Luna Guevara

2013-06-01

Full Text Available Nuts contain in their composition nutrients and bioactive compounds that when consumed in sufficient amounts may provide health benefits. In this study was evaluated the influence of the addition of residual pastes (10%, obtained from the extraction of oil from walnut (Juglans regia L., pecan (Carya illinoinensis (Wangenh. K. Koch, variety Western Shley, and peanut (Arachis hypogaea, on the modification of some textural, proximate, physicochemical, microbiological and sensory characteristics of cooked hams. Hams were stored at 4 ° C for 21 days. Hams containing pastes significantly increased (P ≤ 0.05 the protein, fat, and total fiber content. Hams added with paste presented a less rigid structures (P ≤ 0.05. The color parameters (L*, a*, and b* of hams decrease slightly during the storage time, except for the ham added with walnut paste, which was darker. The nut pastes contributed significantly (P ≤ 0.05 to decrease the shelf life of hams. However, the yeast and mold counts in ham were less than 10 CFU/g at 21 days of storage. aw and pH decreased significantly (P ≤ 0.05 and syneresis increased during storage. Hams added with residual pastes were well sensory accepted regarding color, aroma, taste, appearance, and overall acceptability.

Bioavailability of chemically-dispersed crude oil

International Nuclear Information System (INIS)

Harris, B.C.; Bonner, J.S.; McDonald, T.J.; Fuller, C.B.; Page, C.A.; Dimitriou-Christidis, P.; Sterling, M.C.; Autenrieth, R.L.

2002-01-01

Oil spills can be treated with surfactant compounds to disperse them. This method enables the hydrophobic compounds to overcome their repulsion for water, enter the water phase and be diluted. Once in the water, the biodegradation fraction of the oil biodegrades over time and the residual fraction is deposited over a large area. One major issue which is not fully understood is whether oil compounds pass through the water phase to free floating cells or directly enter oil-attached microbial cells from the oil particle. In this study, crude oil was placed in a swirling flask with Corpus Christi Bay water and was then chemically dispersed with Corexit 9500. The biodegradation was then monitored and assessed. First order rate coefficients were determined based on the disappearance of specific compounds. The rate coefficients for total target PAHs were consistent for all tests. Napthalene, phenanthrene, dibenzothiophene and their alkylated homologs were among the target compounds. The trend was also observed for total target analytes and for total target saturates. The results indicate that the biodegradation rate coefficient was not dependent on the bulk concentration of oil in the water column. It was concluded that biodegradation rates was controlled by partitioning of the compounds between the two phases, and other factors such as particle size distribution and the capability of the microbial culture, temperature and nutrients. 13 refs., 1 tab., 6 figs

Study on the Antimicrobial activity and Minimum Inhibitory Concentration of Essential Oils of Spices

Directory of Open Access Journals (Sweden)

R.V.N.Srujan and M.Sravanthi

Full Text Available Antibacterial activity and minimum inhibitory concentration (MIC of essential oils of garlic, clove and cinnamon were estimated by using various bacterial pathogens. Among the bacterial pathogens tested against essential oil of garlic, Staphylococcus aureus was found to be highly sensitive followed by E.coli. L.monocytogenes and S.pyogenes were found to be less sensitive. The essential oil of clove was found to be most active against S.aureus followed by E.coli. B.cereus and C. jejuni. The essential oil of cinnamon was also most active against S.aureus followed by E.coli and C.jejuni. Essential oil of cinnamon was found to be active against all the bacterial pathogens tested, when compared to garlic and clove oils. However Staph. aureus, E. coli and C.jejuni were found to be most sensitive to the action of essential oils of garlic, clove and cinnamon. Among the bacterial pathogens tested against essential oils of spices to know the MIC by agar diffusion method, C.jejuni was found to be most sensitive to the essential oil of garlic followed by E.coli, S. typhimurium and Staphylococcus aureus. L. monocytogenes and Methicillin resistant Staph. aureus were found to be comparatively less sensitive. Essential oil of clove was also found to be highly effective against C.jejuni followed by E.coli, S.typhimurium and S.aureus. Again L.monocytogenes and Methicillin resistant S.aureus were comparatively less sensitive to the action of essential oil of clove. All most all the bacterial pathogens tested were found to be sensitive to the essential oil of cinnamon. However C.jejuni and E.coli were found to be most sensitive followed by S.typhimurium, Staph. aureus and Methicillin resistant Staph. aureus . [Vet. World 2011; 4(7.000: 311-316

Concentrations and dissipation of difenoconazole and fluxapyroxad residues in apples and soil, determined by ultrahigh-performance liquid chromatography electrospray ionization tandem mass spectrometry.

Science.gov (United States)

He, Min; Jia, Chunhong; Zhao, Ercheng; Chen, Li; Yu, Pingzhong; Jing, Junjie; Zheng, Yongquan

2016-03-01

A new combined difenoconazole and fluxapyroxad fungicide formulation, as an 11.7 % suspension concentrate (SC), has been introduced as part of a resistance management strategy. The dissipation of difenoconazole and fluxapyroxad applied to apples and the residues remaining in the apples were determined. The 11.7 % SC was sprayed onto apple trees and soil in Beijing, Shandong, and Anhui provinces, China, at an application rate of 118 g a.i. ha(-1), then the dissipation of difenoconazole and fluxapyroxad was monitored. The residual difenoconazole and fluxapyroxad concentrations were determined by ultrahigh-performance liquid chromatography tandem mass spectrometry. The difenoconazole half-lives in apples and soil were 6.2-9.5 and 21.0-27.7 days, respectively. The fluxapyroxad half-lives in apples and soil were 9.4-12.6 and 10.3-36.5 days, respectively. Difenoconazole and fluxapyroxad residues in apples and soil after the 11.7 % SC had been sprayed twice and three times, with 10 days between applications, at 78 and 118 g a.i. ha(-1) were measured. Representative apple and soil samples were collected after the last treatment, at preharvest intervals of 14, 21, and 28 days. The difenoconazole residue concentrations in apples and soil were 0.002-0.052 and 0.002-0.298 mg kg(-1), respectively. The fluxapyroxad residue concentrations in apples and soil were 0.002-0.093 and 0.008-1.219 mg kg(-1), respectively. The difenoconazole and fluxapyroxad residue concentrations in apples were lower than the maximum residue limits (0.5 and 0.8 mg kg(-1), respectively). An application rate of 78 g a.i. ha(-1) is therefore recommended to ensure that treated apples can be considered safe for humans to consume.

Investigation of Technological Operations Affecting the Determination of Concentration of Ionol Additive in Insulating Oil in High-Voltage Equipment

Directory of Open Access Journals (Sweden)

Korobeynikov S.M.

2018-04-01

Full Text Available Ionol oxidation inhibitor level control is included into normative indicators list for diagnostics of internal insulation condition of any oil-filled high voltage device. Concentration of oxidation inhibitor in dielectric liquid should be from 0,08 % to 0,40 % mass. Power supply network chemistry laboratories use such methods as spectroscopy, spectrometry, chromatography and many others. Russian insulation service specialists use the method of ionol concentration measurement in oils based on gas-liquid chromatography. In the first place it is related to the fact that gas chromatographs are installed for several tasks, including definition of inhibitor’s mass concentration. However, as practice shows, the use of this method for additive analysis, especially in old acidified mineral oils is linked to some difficulties. The aim of this work is identify technologic faults that may occur during definition of ionol inhibitive additive in dielectric liquid with gas-liquid chromatography method, and, as a consequence, may lead to incorrect calculation of ionol additional concentration to oil, necessary for its antioxygenic properties maintenance and high insulation quality provision during high voltage device functioning. The object of the research is insulating oil with more than 35 years’ operating cycle, presenting a complex multiplex matrix of hydrocarbons and oxygenates preventing reliable determination of ionol additive with gas-liquid chromatography method. Executed researches show that the main input into “correct” final result obtention during calculation of additional additive concentration was made by such technological operations as water content in extractant and technology of sample introduction into chromatograph’s evaporation tank

Thorium, uranium and rare earth elements content in lanthanide concentrate (LC) and water leach purification (WLP) residue of Lynas advanced materials plant (LAMP)

Science.gov (United States)

AL-Areqi, Wadeeah M.; Majid, Amran Ab.; Sarmani, Sukiman

2014-02-01

Lynas Advanced Materials Plant (LAMP) has been licensed to produce the rare earths elements since early 2013 in Malaysia. LAMP processes lanthanide concentrate (LC) to extract rare earth elements and subsequently produce large volumes of water leach purification (WLP) residue containing naturally occurring radioactive material (NORM). This residue has been rising up the environmental issue because it was suspected to accumulate thorium with significant activity concentration and has been classified as radioactive residue. The aim of this study is to determine Th-232, U-238 and rare earth elements in lanthanide concentrate (LC) and water leach purification (WLP) residue collected from LAMP and to evaluate the potential radiological impacts of the WLP residue on the environment. Instrumental Neutron Activation Analysis and γ-spectrometry were used for determination of Th, U and rare earth elements concentrations. The results of this study found that the concentration of Th in LC was 1289.7 ± 129 ppm (5274.9 ± 527.6Bq/kg) whereas the Th and U concentrations in WLP were determined to be 1952.9±17.6 ppm (7987.4 ± 71.9 Bq/kg) and 17.2 ± 2.4 ppm respectively. The concentrations of Th and U in LC and WLP samples determined by γ- spectrometry were 1156 ppm (4728 ± 22 Bq/kg) & 18.8 ppm and 1763.2 ppm (7211.4 Bq/kg) &29.97 ppm respectively. This study showed that thorium concentrations were higher in WLP compare to LC. This study also indicate that WLP residue has high radioactivity of 232Th compared to Malaysian soil natural background (63 - 110 Bq/kg) and come under preview of Act 304 and regulations. In LC, the Ce and Nd concentrations determined by INAA were 13.2 ± 0.6% and 4.7 ± 0.1% respectively whereas the concentrations of La, Ce, Nd and Sm in WLP were 0.36 ± 0.04%, 1.6%, 0.22% and 0.06% respectively. This result showed that some amount of rare earth had not been extracted and remained in the WLP and may be considered to be reextracted.

Thorium, uranium and rare earth elements content in lanthanide concentrate (LC) and water leach purification (WLP) residue of Lynas advanced materials plant (LAMP)

International Nuclear Information System (INIS)

AL-Areqi, Wadeeah M.; Majid, Amran Ab.; Sarmani, Sukiman

2014-01-01

Lynas Advanced Materials Plant (LAMP) has been licensed to produce the rare earths elements since early 2013 in Malaysia. LAMP processes lanthanide concentrate (LC) to extract rare earth elements and subsequently produce large volumes of water leach purification (WLP) residue containing naturally occurring radioactive material (NORM). This residue has been rising up the environmental issue because it was suspected to accumulate thorium with significant activity concentration and has been classified as radioactive residue. The aim of this study is to determine Th-232, U-238 and rare earth elements in lanthanide concentrate (LC) and water leach purification (WLP) residue collected from LAMP and to evaluate the potential radiological impacts of the WLP residue on the environment. Instrumental Neutron Activation Analysis and γ-spectrometry were used for determination of Th, U and rare earth elements concentrations. The results of this study found that the concentration of Th in LC was 1289.7 ± 129 ppm (5274.9 ± 527.6Bq/kg) whereas the Th and U concentrations in WLP were determined to be 1952.9±17.6 ppm (7987.4 ± 71.9 Bq/kg) and 17.2 ± 2.4 ppm respectively. The concentrations of Th and U in LC and WLP samples determined by γ- spectrometry were 1156 ppm (4728 ± 22 Bq/kg) and 18.8 ppm and 1763.2 ppm (7211.4 Bq/kg) and 29.97 ppm respectively. This study showed that thorium concentrations were higher in WLP compare to LC. This study also indicate that WLP residue has high radioactivity of 232 Th compared to Malaysian soil natural background (63 - 110 Bq/kg) and come under preview of Act 304 and regulations. In LC, the Ce and Nd concentrations determined by INAA were 13.2 ± 0.6% and 4.7 ± 0.1% respectively whereas the concentrations of La, Ce, Nd and Sm in WLP were 0.36 ± 0.04%, 1.6%, 0.22% and 0.06% respectively. This result showed that some amount of rare earth had not been extracted and remained in the WLP and may be considered to be reextracted

Thorium, Uranium and Rare Earth Elements content in lanthanide concentrate (LC) and water leach purification (WLP) residue of Lynas Advanced Materials Plant (LAMP)

International Nuclear Information System (INIS)

Al-Areqi, W.M.; Amran Abdul Majid; Sukiman Sarmani

2013-01-01

Full-text: Lynas Advanced Materials Plant (LAMP) has been licensed to produce the rare earths elements since early 2013 in Malaysia. LAMP processes lanthanide concentrate (LC) to extract rare earth elements and subsequently produce large volumes of water leach purification (WLP) residue containing naturally occurring radioactive material (NORM). This residue has been rising up the environmental issue because it was suspected to accumulate thorium with significant activity concentration and has been classified as radioactive residue. The aim of this study is to determine Th-232, U-238 and rare earth elements in lanthanide concentrate (LC) and water leach purification (WLP) residue collected from LAMP and to evaluate the potential radiological impacts of the WLP residue on the environment. Instrumental Neutron Activation Analysis and γ-spectrometry were used for determination of Th, U and rare earth elements concentrations. The results of this study found that the concentration of Th in LC was 1289.7 ± 129 ppm (5274.9 ± 527.6 Bq/ kg) whereas the Th and U concentrations in WLP were determined to be 1952.9 ± 17.6 ppm (7987.4 ± 71.9 Bq/ kg) and 17.2 ± 2.4 ppm respectively. The concentrations of Th and U in LC and WLP samples determined by γ- spectrometry were 1156 ppm (4728 ± 22 Bq/ kg) and 18.8 ppm and 1763.2 ppm (7211.4 Bq/ kg) and 29.97 ppm respectively. This study showed that thorium concentrations were higher in WLP compare to LC. This study also indicate that WLP residue has high radioactivity of 232 Th compared to Malaysian soil natural background (63 - 110 Bq/ kg) and come under preview of Act 304 and regulations. In LC, the Ce and Nd concentrations determined by INAA were 13.2 ± 0.6 % and 4.7 ± 0.1 % respectively whereas the concentrations of La, Ce, Nd and Sm in WLP were 0.36 ± 0.04 %, 1.6 %, 0.22 % and 0.06 % respectively. This result showed that some amount of rare earth had not been extracted and remained in the WLP and may be considered to be re

Thorium, uranium and rare earth elements content in lanthanide concentrate (LC) and water leach purification (WLP) residue of Lynas advanced materials plant (LAMP)

Energy Technology Data Exchange (ETDEWEB)

AL-Areqi, Wadeeah M., E-mail: walareqi@yahoo.com; Majid, Amran Ab., E-mail: walareqi@yahoo.com; Sarmani, Sukiman, E-mail: walareqi@yahoo.com [Nuclear Science Programme, School of Chemical Sciences and Food Technology, Faculty of Science and Technology, Universiti Kebangsaan Malaysia, 43600 Bangi (Malaysia)

2014-02-12

Lynas Advanced Materials Plant (LAMP) has been licensed to produce the rare earths elements since early 2013 in Malaysia. LAMP processes lanthanide concentrate (LC) to extract rare earth elements and subsequently produce large volumes of water leach purification (WLP) residue containing naturally occurring radioactive material (NORM). This residue has been rising up the environmental issue because it was suspected to accumulate thorium with significant activity concentration and has been classified as radioactive residue. The aim of this study is to determine Th-232, U-238 and rare earth elements in lanthanide concentrate (LC) and water leach purification (WLP) residue collected from LAMP and to evaluate the potential radiological impacts of the WLP residue on the environment. Instrumental Neutron Activation Analysis and γ-spectrometry were used for determination of Th, U and rare earth elements concentrations. The results of this study found that the concentration of Th in LC was 1289.7 ± 129 ppm (5274.9 ± 527.6Bq/kg) whereas the Th and U concentrations in WLP were determined to be 1952.9±17.6 ppm (7987.4 ± 71.9 Bq/kg) and 17.2 ± 2.4 ppm respectively. The concentrations of Th and U in LC and WLP samples determined by γ- spectrometry were 1156 ppm (4728 ± 22 Bq/kg) and 18.8 ppm and 1763.2 ppm (7211.4 Bq/kg) and 29.97 ppm respectively. This study showed that thorium concentrations were higher in WLP compare to LC. This study also indicate that WLP residue has high radioactivity of {sup 232}Th compared to Malaysian soil natural background (63 - 110 Bq/kg) and come under preview of Act 304 and regulations. In LC, the Ce and Nd concentrations determined by INAA were 13.2 ± 0.6% and 4.7 ± 0.1% respectively whereas the concentrations of La, Ce, Nd and Sm in WLP were 0.36 ± 0.04%, 1.6%, 0.22% and 0.06% respectively. This result showed that some amount of rare earth had not been extracted and remained in the WLP and may be considered to be reextracted.

Prediction of long-residue properties of potential blends from mathematically mixed infrared spectra of pure crude oils by partial least-squares regression models

NARCIS (Netherlands)

de Peinder, P.; Visser, T.; Petrauskas, D.D.; Salvatori, F.; Soulimani, F.; Weckhuysen, B.M.

2009-01-01

Research has been carried out to determine the feasibility of partial least-squares (PLS) regression models to predict the long-residue (LR) properties of potential blends from infrared (IR) spectra that have been created by linearly co-adding the IR spectra of crude oils. The study is the follow-up

The relationship between total phenol concentration and the perceived style of extra virgin olive oil

Directory of Open Access Journals (Sweden)

2009-06-01

Full Text Available The degree of bitterness and pungency of a virgin olive oil largely defines its style, and therefore how it is most appropriately used by consumers. In order to assess how Australian olive oil producers interpret the style of their oils, 920 Australian virgin olive oils were classified by their producers as either being mild, medium or robust in style. Although in general, the classifications by producers were associated with the oils’ total phenol concentration, significant variability in phenol concentration within each style category was observed. The perceived styles of a subset of these oils were further assessed by panels of expert tasters. The expert panels were more discriminating when assigning oils to style categories based on total phenol levels. The producers and the expert panels were in moderate agreement with respect to oil style, with the interpretation of what constitutes a mild oil being the most contentious.

El grado de amargor y picante de un aceite de oliva define en gran manera su tipo, y, por tanto, también su uso más apropiado por el consumidor. Para evaluar cómo los productores australianos de aceite de oliva interpretan el tipo de sus aceites, 920 aceites de oliva virgen australianos fueron clasificados por sus productores en tipo suave, medio o fuerte. Aunque, en general, la clasificación de los productores estuvo asociada a la concentración de fenoles totales de los aceites, se observó una variabilidad significativa en la concentración de fenoles en cada tipo de aceite. Los tipos percibidos en un subgrupo de estos aceites fueron además evaluados por paneles de catadores expertos. Los paneles de expertos fueron más discriminantes cuando asignaron los aceites a los diversos tipos basándose en el nivel de fenoles totales. Los productores y los paneles de expertos estuvieron en relativamente de acuerdo con respecto al tipo de aceite, si bien la interpretación de qué es un aceite suave fue la m

Global sensitivity analysis of Alkali-Surfactant-Polymer enhanced oil recovery processes

Energy Technology Data Exchange (ETDEWEB)

Carrero, Enrique; Queipo, Nestor V.; Pintos, Salvador; Zerpa, Luis E. [Applied Computing Institute, Faculty of Engineering, University of Zulia, Zulia (Venezuela)

2007-08-15

After conventional waterflooding processes the residual oil in the reservoir remains as a discontinuous phase in the form of oil drops trapped by capillary forces and is likely to be around 70% of the original oil in place (OOIP). The EOR method so-called Alkaline-Surfactant-Polymer (ASP) flooding has been proved to be effective in reducing the oil residual saturation in laboratory experiments and field projects through reduction of interfacial tension and mobility ratio between oil and water phases. A critical step for the optimal design and control of ASP recovery processes is to find the relative contributions of design variables such as, slug size and chemical concentrations, in the variability of given performance measures (e.g., net present value, cumulative oil recovery), considering a heterogeneous and multiphase petroleum reservoir (sensitivity analysis). Previously reported works using reservoir numerical simulation have been limited to local sensitivity analyses because a global sensitivity analysis may require hundreds or even thousands of computationally expensive evaluations (field scale numerical simulations). To overcome this issue, a surrogate-based approach is suggested. Surrogate-based analysis/optimization makes reference to the idea of constructing an alternative fast model (surrogate) from numerical simulation data and using it for analysis/optimization purposes. This paper presents an efficient global sensitivity approach based on Sobol's method and multiple surrogates (i.e., Polynomial Regression, Kriging, Radial Base Functions and a Weighed Adaptive Model), with the multiple surrogates used to address the uncertainty in the analysis derived from plausible alternative surrogate-modeling schemes. The proposed approach was evaluated in the context of the global sensitivity analysis of a field scale Alkali-Surfactant-Polymer flooding process. The design variables and the performance measure in the ASP process were selected as slug size/concentration

Anaerobic digestion of residues from production and refining of vegetable oils as an alternative to conventional solutions.

Science.gov (United States)

Torrijos, M; Thalla, Arun Kumar; Sousbie, P; Bosque, F; Delgenès, J P

2008-01-01

The purpose of this work was to study the anaerobic digestion of by-products generated during the production and refining of oil with the objective of proposing an alternative solution (methanisation) to the conventional solutions while reducing the energy consumption of fossil origin on refinery sites. The production of sunflower oil was taken as example. Glycerine from the production of biodiesel was also included in this study. The results show that glycerine has a high potential for methanisation because of its high methane potential (465 ml CH4/g VS) and high metabolization rates (0.42 g VS/g VSS.d). The use of oil cake as substrate for anaerobic digestion is not interesting because it has a low methane potential of 215 ml CH4/g VS only and because it is easily recovered in animal feed. Six residues have quite a high methane potential (465 to 850 ml CH4/g VS) indicating a good potential for anaerobic digestion. However, they contain a mixture of rapidly and slowly biodegradable organic matter and the loading rates must remain quite low (0.03 to 0.09 g VS/g VSS.d) to prevent any accumulation of slowly biodegradable solids in the digesters. IWA Publishing 2008.

Role of the thickening agent concentration and surfactant additions in the system's soap-oil

Energy Technology Data Exchange (ETDEWEB)

Shchegolev, G.G.; Trapeznikov, A.A.; Taranenko, V.G.

1973-03-01

The effect of the thickening agent concentration, surfactant additions and mechanical treatment on the microstructure and structural-mechanical properties of the system's lithium stearate-oil has been studied. The rate of cooling of the soap-oil system has been shown also to be of importance. The surfactants are less effective when introduced into a finished pseudogel, than when added during crystallization.

Carotenoids concentration of Gac (Momordica cochinchinensis Spreng.) fruit oil using cross-flow filtration technology.

Science.gov (United States)

Mai, Huỳnh Cang; Truong, Vinh; Debaste, Frédéric

2014-11-01

Gac (Momordica cochinchinensis Spreng.) fruit, a traditional fruit in Vietnam and other countries of eastern Asia, contains an oil rich in carotenoids, especially lycopene and β-carotene. Carotenoids in gac fruit oil were concentrated using cross-flow filtration. In total recycle mode, effect of membrane pore size, temperature, and transmembrane pressure (TMP) on permeate flux and on retention coefficients has been exploited. Resistance of membrane, polarization concentration, and fouling were also analyzed. Optimum conditions for a high permeate flux and a good carotenoids retention are 5 nm, 2 bars, and 40 °C of membrane pore size, TMP, and temperature, respectively. In batch mode, retentate was analyzed through index of acid, phospholipids, total carotenoids content (TCC), total antioxidant activity, total soluble solids, total solid content, color measurement, and viscosity. TCC in retentate is higher 8.6 times than that in feeding oil. Lipophilic antioxidant activities increase 6.8 times, while hydrophilic antioxidant activities reduce 40%. The major part of total resistance is due to polarization (55%) while fouling and intrinsic membrane contribute about 30% and 24%, respectively. © 2014 Institute of Food Technologists®

Effects of sodium caseinate concentration and storage conditions on the oxidative stability of oil-in-water emulsions.

Science.gov (United States)

O' Dwyer, Sandra P; O' Beirne, David; Eidhin, Deirdre Ní; O' Kennedy, Brendan T

2013-06-01

The oxidative stability of various oils (sunflower, camelina and fish) and 20% oil-in-water (O/W) emulsions, were examined. The mean particle size decreased from 1179 to 325 nm as sodium caseinate (emulsifier) concentration was increased from 0.25% to 3% in O/W emulsions (Psodium caseinate concentration increased, and similarly decreased as microfluidisation pressure increased (P<0.05). Increasing storage temperature of the emulsions from 5 to 60°C, resulted in lower detectable lipid oxidation products during storage (P<0.05). Copyright © 2012 Elsevier Ltd. All rights reserved.

Mechanisms of microbial oil recovery by Clostridium acetobutylicum and Bacillus strain JF-2

Energy Technology Data Exchange (ETDEWEB)

Marsh, T.L.; Zhang, X.; Knapp, R.M.; McInerney, M.J.; Sharma, P.K.; Jackson, B.E.

1995-12-31

Core displacement experiments at elevated pressures were conducted to determine whether microbial processes are effective under conditions that simulate those found in an actual oil reservoir. The in-situ growth of Clostridium acetobutylicum and Bacillus strain JF-2 resulted in the recovery of residual oil. About 21 and 23% of the residual oil was recovered by C. acetobutylicum and Bacillus strain JF-2, respectively. Flooding cores with cell-free culture fluids of C. acetobutylicum with and without the addition of 50 mM acetone and 100 mM butanol did not result in the recovery of residual oil. Mathematical simulations showed that the amount of gas produced by the clostridial fermentation was not showed that the amount of gas produced by the clostridial fermentation was not sufficient to recover residual oil. Oil recovery by Bacillus strain JF-2 was highly correlated to surfactant production. A biosurfactant-deficient mutant of strain JF-2 was not capable of recovering residual oil. These data show that surfactant production is an important mechanism for microbially enhanced oil recovery. The mechanism for oil recovery by C. acetobutylicum is not understood at this time, but the production of acids, solvents, or gases alone cannot explain the observed increases in oil recovery by this organism.

EVALUATION OF FERRIC CHLORIDE AND ALUM EFFICIENCIES IN ENHANCED COAGULATION FOR TOC REMOVAL AND RELATED RESIDUAL METAL CONCENTRATIONS

Directory of Open Access Journals (Sweden)

A. Mesdaghinia, M. T. Rafiee, F. Vaezi and A. H. Mahvi

2005-07-01

Full Text Available Although the removal of colloidal particles continues to be an important reason for using coagulation, a newer objective, the removal of natural organic matter (NOM to reduce the formation of disinfection by-products (DBPs, is growing in importance. Enhanced coagulation is thus introduced to most water utilities treating surface water. Bench-scale experiments were conducted to compare the effectiveness of alum and ferric chloride in removing DBPs precursors from eight synthetic water samples, each representing a different element of the USEPA’s 3×3 enhanced coagulation matrix. The effect of enhanced coagulation on the residual metal (aluminum/iron concentration in the treated water was assessed as well. The removal of total organic carbon (TOC was dependent on the coagulant type and was enhanced with increasing coagulant dose, but the latter had no further considerable effect in case of increasing to high levels. For all the treated samples coagulation with ferric chloride proved to be more effective than alum at similar doses and the mean values of treatment efficiencies were 51% and 32% for ferric chloride and alum, respectively. Ferric chloride was therefore considered the better chemical for enhancing the coagulation process. Besides, due to less production of sludge by this coagulant, it would be predicted that treatment plants would be confronted to fewer problems with respect to final sludge disposal. Measurements of residual metal in treated water indicated that iron and aluminum concentrations had been increased as expected but the quality of water concerning the residual metal deteriorated much more in cases of under-dosing. Despite expecting high residual Al and Fe concentrations under enhanced coagulation, metal concentrations were frequently remained low and were not increased appreciably.

A Study of the Use of Jatropha Oil Blends in Boilers

Energy Technology Data Exchange (ETDEWEB)

Krishna, C.R.

2010-10-01

Executive Summary: This project investigated the combustion performance of blends of unrefined Jatropha oil and its blends in laboratory boilers. Although a very limited amount of testing blends in distillate oil, ASTM No. 2 oil or heating oil was conducted, the primary interest was in testing the performance of blends with residual ASTM No. 6 oil. The basic idea is to provide a renewable fuel option to residual oil used in space heating and in industrial applications. The intent also was to explore the use of non-edible plant oil and one that might be potentially cheaper than biodiesel. The characteristics of No. 6 oil, such as high viscosity at ambient temperature, which requires it to be kept heated, make the blending with such oils feasible. Jatropha oil is one such oil and there is currently considerable interest building up in its use as a source for making biodiesel and jet fuel. A 10% blend of Jatropha oil with heating oil was burned using a standard burner in a residential boiler. Combustion performance was shown to be comparable with that of burning heating oil by itself with some noticeable differences. Typical heating oil has about 2000 ppm of sulfur, while the Jatropha oil has about 50 ppm leading to lower levels of sulphur dioxide emissions. Stack measurements also showed that the NOx emission was lower with the blend. We have previously reported similar reductions in NOx with blends of biodiesel in heating oil as well as slight reductions in PM2.5, particulates below 2.5 microns in size. Long term tests were not part of this project and hence deleterious effects on pumps, seals etc., if any, were not measured. The majority of the work involved testing blends of Jatropha oil with residual oil in a 1.5 million Btu/hr boiler with a burner modified to burn residual oil. Blends of 20 and 60% Jatropha oil and 100% Jatropha oil were burned in the combustion performance tests. The residual oil used had a sulfur content of over 2000 ppm and hence dramatic

Factors inhibiting bioremediation of soil contaminated with weathered oils and drill cuttings

International Nuclear Information System (INIS)

Chaillan, F.; Chaineau, C.H.; Point, V.; Saliot, A.; Oudot, J.

2006-01-01

Oily drill cuttings and a soil contaminated with weathered crude oils were treated by enhanced biodegradation under tropical conditions in industrial scaled experiments. Oil contaminants were characterized by gas chromatography and mass spectrometry. This allowed for the identification of a mixture of two crude oils in the contaminated soil. After 12 months of bioremediation process, the removal of hydrocarbons reached by biodegradation an extent of 60% although nutrient amendment with elevated concentration of N-urea had highly detrimental effects on the hydrocarbon degrading fungal populations due to the production of toxic concentration of ammonia gas by nitrification. The saturated hydrocarbons were extensively assimilated, though n-alkanes were not completely removed. Aromatic hydrocarbons were less degraded than saturated whereas resin and asphaltene fractions were, surprisingly, partly assimilated. In laboratory conditions, the residual hydrocarbons in the field-treated materials were 15-20% further degraded when metabolic byproducts resulting from biodegradation were diluted or removed. - Bioremediation of oil-polluted soils can be impaired if urea is used as nitrogen source, and metabolic byproducts can limit biodegradation rates in industrial scaled experiments

Capillary-Physics Mechanism of Elastic-Wave Mobilization of Residual Oil

Science.gov (United States)

Beresnev, I. A.; Pennington, W. D.; Turpening, R. M.

2003-12-01

Much attention has been given to the possibility of vibratory mobilization of residual oil as a method of enhanced recovery. The common features of the relevant applications have nonetheless been inconsistency in the results of field tests and the lack of understanding of a physical mechanism that would explain variable experiences. Such a mechanism can be found in the physics of capillary trapping of oil ganglia, driven through the pore channels by an external pressure gradient. Entrapping of ganglia occurs due to the capillary pressure building on the downstream meniscus entering a narrow pore throat. The resulting internal-pressure imbalance acts against the external gradient, which needs to exceed a certain threshold to carry the ganglion through. The ganglion flow thus exhibits the properties of the Bingham (yield-stress) flow, not the Darcy flow. The application of vibrations is equivalent to the addition of an oscillatory forcing to the constant gradient. When this extra forcing acts along the gradient, an instant "unplugging" occurs, while, when the vibration reverses direction, the flow is plugged. This asymmetry results in an average non-zero flow over one period of vibration, which explains the mobilization effect. The minimum-amplitude and maximum-frequency thresholds apply for the mobilization to occur. When the vibration amplitude exceeds a certain "saturation" level, the flow returns to the Darcy regime. The criterion of the mobilization of a particular ganglion involves the parameters of both the medium (pore geometry, interfacial and wetting properties, fluid viscosity) and the oscillatory field (amplitude and frequency). The medium parameters vary widely under natural conditions. It follows that an elastic wave with a given amplitude and frequency will always produce a certain mobilization effect, mobilizing some ganglia and leaving others intact. The exact macroscopic effect is hard to predict, as it will represent a response of the populations

Clay-oil flocculation and its role in natural cleansing in Prince William Sound following the Exxon Valdez oil spill

International Nuclear Information System (INIS)

Bragg, J.R.; Yang, S.H.

1995-01-01

Natural interactions of fine mineral particles with residue oil and seawater, in a process called clay-oil flocculation, were found to create solids-stabilized oil-in-water emulsions on shoreline sediments at numerous locations in Prince William Sound following the Exxon Valdez spill. In laboratory tests using oiled sediment samples from Prince William Sound, these emulsions were shown to facilitate natural cleansing and dispersion of oil from sediments by moving water. To investigate the effect of flocculation on natural cleansing, studies were conducted to determine the hydrodynamic energy needed for seawater to remove flocculated oil residues from sediments sampled from shorelines. Water was pumped at different velocities through a column packed with oiled sediment, and the amount and composition of oil removed from the sediment were measured as functions of water velocity and sediment movement. In separate tests, oil removal was observed in a wave tank that generated wave heights less than and greater than needed to move sediments. 28 refs., 13 figs., 7 tabs

Control of coffee berry borer, Hypothenemus hampei (Ferrari (Coleoptera: Curculionidae: Scolytinae with botanical insecticides and mineral oils

Directory of Open Access Journals (Sweden)

Flávio Neves Celestino

2016-01-01

Full Text Available The objective of this study was to evaluate botanical oils, mineral oils and an insecticide that contained azadirachtin (ICA for the control of Hypothenemus hampei, in addition to the effects of residual castor oil. We evaluated the effectiveness of the vegetable oils of canola, sunflower, corn, soybean and castor, two mineral oils (assist® and naturol®, and the ICA for the control of H. hampei. The compounds were tested at a concentration of 3.0% (v v-1. The median lethal concentration (LC50 was estimated with Probit analysis. The oil of castor bean and extract of castor bean cake were also evaluated at concentrations of 3.0% (v v-1 and 3.0% (m v-1, respectively. The mortality rates for H. hampei caused by the ICA and the castor oil were 40.8 and 53.7%, with LC50 values of 6.71 and 3.49% (v v-1, respectively. In the castor oil, the methyl esters of the fatty acids were palmitic (1.10%, linoleic (4.50%, oleic (4.02%, stearic (0.50% and ricinoleic acids (88.04%. The extract of the castor bean cake was not toxic to H. hampei. The persistence of the castor oil in the environment was low, and the cause of mortality for H. hampei was most likely the blockage of the spiracles, which prevented the insects from breathing.

Unilever food safety assurance system for refined vegetable oils and fats

Directory of Open Access Journals (Sweden)

van Duijn Gerrit

2010-03-01

Full Text Available The Unilever Food Safety Assurance system for refined oils and fats is based on risk assessments for the presence of contaminants or pesticide residues in crude oils, and refining process studies to validate the removal of these components. Crude oil risk assessments were carried out by combining supply chain visits, and analyses of the contaminant and pesticide residue levels in a large number of crude oil samples. Contaminants like poly-aromatic hydrocarbons and hydrocarbons of mineral origin, and pesticide residues can largely be removed by refining. For many years, this Food Safety Assurance System has proven to be effective in controlling contaminant levels in refined vegetable oils and fats.

Access to residual carrier concentration in ZnO nanowires by calibrated scanning spreading resistance microscopy

Energy Technology Data Exchange (ETDEWEB)

Wang, L., E-mail: lin.wang@insa-lyon.fr; Brémond, G. [Institut des Nanotechnologies de Lyon (INL), Université de Lyon, CNRS UMR 5270, INSA Lyon, Bat. Blaise Pascal, 7 Avenue Jean Capelle, 69621 Villeurbanne (France); Chauveau, J. M. [Centre de Recherche sur l' Hétéro-Epitaxie et ses Applications (CRHEA), CNRS UPR10, rue Bernard Grégory 06560 Valbonne Sophia Antipolis (France); Physics Department, University of Nice Sophia Antipolis (UNS), Parc Valrose, 06103 Nice (France); Brenier, R. [Institut Lumière Matière (ILM), Université de Lyon, CNRS UMR 5306, Université Claude Bernard Lyon 1, 43 Boulevard du 11 Novembre 1918, 69622 Villeurbanne (France); Sallet, V.; Jomard, F.; Sartel, C. [Groupe d' Étude de la Matière Condensée (GEMaC), CNRS-Université de Versailles St Quentin en Yvelines, Université Paris-Saclay, 45 Avenue des Etats-Unis, 78035 Versailles (France)

2016-03-28

Scanning spreading resistance microscopy (SSRM) was performed on non-intentionally doped (nid) ZnO nanowires (NWs) grown by metal-organic chemical vapor deposition in order to measure their residual carrier concentration. For this purpose, an SSRM calibration profile has been developed on homoepitaxial ZnO:Ga multilayer staircase structures grown by molecular beam epitaxy. The Ga density measured by SIMS varies in the 1.7 × 10{sup 17 }cm{sup −3} to 3 × 10{sup 20 }cm{sup −3} range. From measurements on such Ga doped multi-layers, a monotonic decrease in SSRM resistance with increasing Ga density was established, indicating SSRM being a well-adapted technique for two dimensional dopant/carrier profiling on ZnO at nanoscale. Finally, relevant SSRM signal contrasts were detected on nid ZnO NWs, and the residual carrier concentration is estimated in the 1–3 × 10{sup 18 }cm{sup −3} range, in agreement with the result from four-probe measurements.

Sequential enrichment of microbial population exhibiting enhanced biodegradation of crude oil

International Nuclear Information System (INIS)

Venkateswaran, Kasthuri; Harayama, Shigeaki.

1995-01-01

The distribution of oil-degrading bacteria in the coastal waters and sediments of Hokkaido, Japan, was surveyed. It was found that the potential of mixed microbial populations to degrade weathered crude oil was not confined to any ecological components (water or sediment) nor to the sampling stations. One microbial culture that was stable during repeated subculturing degraded 45% of the saturates and 20% of the aromatics present in crude oil in 10 days during the initial screening. The residual hydrocarbons in this culture were extracted by chloroform and dispersed in a fresh seawater-based medium and subsequently inoculated with microorganisms from the first culture. After full growth of the second culture, the residual hydrocarbons were extracted and dispersed in a fresh medium in which microorganisms from the second culture had been inoculated. This sequential process was carried out six times to enrich those microorganisms that grew on the recalcitrant components of crude oil. After repeated exposure of the residual crude oil to the enriched microorganisms, about 80% of the initially added crude oil was degraded. The cultures obtained after each enrichment cycle were kept, and the degradation of fresh crude oil by the enriched microorganisms was monitored. The degrading activity of the enriched cultures increased as the number of enrichment cycles increased. A microbial population that had been selected six times on the residual crude oil could degrade 70% of the saturates and 30% of the aromatics of crude oil, indicating that growth of a microbial population on residual crude oil improved its ability to biodegrade crude oil. 21 refs., 2 tabs., 7 figs

Utilization of oil palm biodiesel solid residue as renewable sources for preparation of granular activated carbon by microwave induced KOH activation.

Science.gov (United States)

Foo, K Y; Hameed, B H

2013-02-01

In this work, preparation of granular activated carbon from oil palm biodiesel solid residue, oil palm shell (PSAC) by microwave assisted KOH activation has been attempted. The physical and chemical properties of PSAC were characterized using scanning electron microscopy, volumetric adsorption analyzer and elemental analysis. The adsorption behavior was examined by performing batch adsorption experiments using methylene blue as dye model compound. Equilibrium data were simulated using the Langmuir, Freundlich and Temkin isotherm models. Kinetic modeling was fitted to the pseudo-first-order, pseudo-second-order and Elovich kinetic models, while the adsorption mechanism was determined using the intraparticle diffusion and Boyd equations. The result was satisfactory fitted to the Langmuir isotherm model with a monolayer adsorption capacity of 343.94mg/g at 30°C. The findings support the potential of oil palm shell for preparation of high surface area activated carbon by microwave assisted KOH activation. Copyright © 2012 Elsevier Ltd. All rights reserved.

Quarterly oil statistics. Second quarter, 1978

Energy Technology Data Exchange (ETDEWEB)

1978-01-01

This issue presents rapid and accurate information on supply and disposal of crude oil, oil products, and natural gas, including production, refinery output, trade, bunkers, refinery fuel and losses and stock changes. Detailed import and export data are given for 42 origins and 29 destinations for crude oil and products. NGL, feedstocks, naphtha, LPG, gasoline, kerosene, gas/diesel oil, and heavy fuel oil (residual) are covered. (DLC)

Assessing fuel spill risks in polar waters: Temporal dynamics and behaviour of hydrocarbons from Antarctic diesel, marine gas oil and residual fuel oil.

Science.gov (United States)

Brown, Kathryn E; King, Catherine K; Kotzakoulakis, Konstantinos; George, Simon C; Harrison, Peter L

2016-09-15

As part of risk assessment of fuel oil spills in Antarctic and subantarctic waters, this study describes partitioning of hydrocarbons from three fuels (Special Antarctic Blend diesel, SAB; marine gas oil, MGO; and intermediate grade fuel oil, IFO 180) into seawater at 0 and 5°C and subsequent depletion over 7days. Initial total hydrocarbon content (THC) of water accommodated fraction (WAF) in seawater was highest for SAB. Rates of THC loss and proportions in equivalent carbon number fractions differed between fuels and over time. THC was most persistent in IFO 180 WAFs and most rapidly depleted in MGO WAF, with depletion for SAB WAF strongly affected by temperature. Concentration and composition remained proportionate in dilution series over time. This study significantly enhances our understanding of fuel behaviour in Antarctic and subantarctic waters, enabling improved predictions for estimates of sensitivities of marine organisms to toxic contaminants from fuels in the region. Copyright © 2016 Elsevier Ltd. All rights reserved.

Thermochemical recycling of mixture of scrap tyres and waste lubricating oil into high caloric value products

Energy Technology Data Exchange (ETDEWEB)

Abdul-Raouf, Manar E.; Maysour, Nermine E.; Abdul-Azim, Abdul-Azim A. [Egyptian Petroleum Research Institute, Nasr City, Cairo (Egypt); Amin, Mahasen S. [Faculty of Science, Benha University, Benha (Egypt)

2010-06-15

Scrap tyres and used lubricating oils represent together growing environmental problem because they are not biodegradable and their components cannot readily be recovered. In the present investigation, the thermochemical recycling of mixture of old tyres with waste lubricating oil by pyrolysis and the value of the products obtained have been studied. First, thermobalance experiments were carried out, studying the influence of the following variables: temperature, type of catalyst and catalyst concentration on the pyrolysis reaction of a mixture of 1/1 wt./wt. oil/tyre ratio. These thermobalance results were thoroughly investigated to study the effect of the main process variables on yields of derived products: oils, gases and solid residue. (author)

Environmental Impacts and Recovery After the Hebei Spirit Oil Spill in Korea.

Science.gov (United States)

Yim, U H; Khim, J S; Kim, M; Jung, J-H; Shim, W J

2017-07-01

The Hebei Spirit oil spill (HSOS) on December 7, 2007 was the worst oil spill recorded in Korea, with the release of approximately 10,900 tons of crude oil and 375 km of coastline polluted along the west coast of Korea. Cleanup operation was conducted by official and contract responders as well as volunteers for massive oil containment and removal of heavy accumulations of stranded oil. Together with the oil cleanup, a long-term environmental impact assessment (EIA) of the HSOS was initiated based on the Marine Environmental Management Act, which covers oil contamination in a multimedia environment, toxic effects on organisms, and ecosystem injury. This review summarizes the long-term monitoring results of HSOS EIA focused on (1) pollution status of seawater, sediment, and bivalves, (2) ecotoxicological effects, and (3) ecosystem recovery. Overall, concentrations of petroleum hydrocarbons in the environment indicated that their concentrations were well down to at or near background or pre-spill contamination levels at most sites after 1 year. The potential toxic effects of residual oils in sediments have decreased to background levels in most coastal areas of Taean. The entire ecosystem in the most affected area of the Taean coasts appear to be considerably, but not fully, recovered at present, namely after 8 years of the HSOS. The presence of lingering oil and elevated contamination levels at several sites still require continuous long-term monitoring.

Optimization of elution salt concentration in stepwise elution of protein chromatography using linear gradient elution data. Reducing residual protein A by cation-exchange chromatography in monoclonal antibody purification.

Science.gov (United States)

Ishihara, Takashi; Kadoya, Toshihiko; Endo, Naomi; Yamamoto, Shuichi

2006-05-05

Our simple method for optimization of the elution salt concentration in stepwise elution was applied to the actual protein separation system, which involves several difficulties such as detection of the target. As a model separation system, reducing residual protein A by cation-exchange chromatography in human monoclonal antibody (hMab) purification was chosen. We carried out linear gradient elution experiments and obtained the data for the peak salt concentration of hMab and residual protein A, respectively. An enzyme-linked immunosorbent assay was applied to the measurement of the residual protein A. From these data, we calculated the distribution coefficient of the hMab and the residual protein A as a function of salt concentration. The optimal salt concentration of stepwise elution to reduce the residual protein A from the hMab was determined based on the relationship between the distribution coefficient and the salt concentration. Using the optimized condition, we successfully performed the separation, resulting in high recovery of hMab and the elimination of residual protein A.

Higher prices at Canadian gas pumps: international crude oil prices or local market concentration? An empirical investigation

International Nuclear Information System (INIS)

Anindya Sen

2003-01-01

There is little consensus on whether higher retail gasoline prices in Canada are the result of international crude oil price fluctuations or local market power exercised by large vertically-integrated firms. I find that although both increasing local market concentration and higher average monthly wholesale prices are positively and significantly associated with higher retail prices, wholesale prices are more important than local market concentration. Similarly, crude oil prices are more important than the number of local wholesalers in determining wholesale prices. These results suggest that movements in gasoline prices are largely the result of input price fluctuations rather than local market structure. (author)

Effect of Safflower Oil on Concentration of Conjugated Linoleic Acid of Kefir Prepared by Low-fat Milk.

Science.gov (United States)

Farsad-Naeimi, Alireza; Imani, Saeid; Arefhosseini, Seyed R; Alizadeh, Mohammad

2015-01-01

Conjugated linoleic acid (CLA) is a special fatty acid in dairy products with unique antioxidant and anti-cancerous effects. Kefir, a milk product, comprises normalized homogenized cow's milk, the fructose and lactulose syrup as well as a symbiotic starter which has improved probiotic characteristics. The study was aimed to discuss patents and to examine the effect of different safflower oil concentrations on CLA content of the kefir drink prepared by low-fat milk. Safflower oil was added at 0.1, 0.3 and 0.5% (V/V) to low-fat cow's milk and six formulations of kefir samples were prepared. The CLA content of the kefir products was measured at pH=6.0 and pH=6.8 by gas chromatography. Acid and bile tolerance of bacterial microenvironment in the products were also determined. Substitution of natural fat content of milk with safflower oil resulted in proportional increase in the CLA contents of kefir in a dose dependent manner. The highest concentration of CLA was found under 0.5% (V/V) of safflower oil at pH 6.0 and temperature of 37 °C. Adding the Safflower oil into milk used for kefir production, increased CLA content from 0.123 (g/100 g) in pure safflower free samples to 0.322 (g/100 g) in samples with 0.5% (V/V) of safflower oil. The current study revealed that substitution of safflower oil with natural fat of cow's milk may help the production of kefir samples with remarkable increase in CLA content of final product.

Total and methyl mercury concentrations in sediment and water of a constructed wetland in the Athabasca Oil Sands Region

International Nuclear Information System (INIS)

Oswald, Claire J.; Carey, Sean K.

2016-01-01

In the Athabasca Oil Sands Region in northeastern Alberta, Canada, oil sands operators are testing the feasibility of peatland construction on the post-mining landscape. In 2009, Syncrude Canada Ltd. began construction of the 52 ha Sandhill Fen pilot watershed, including a 15 ha, hydrologically managed fen peatland built on sand-capped soft oil sands tailings. An integral component of fen reclamation is post-construction monitoring of water quality, including salinity, fluvial carbon, and priority pollutant elements. In this study, the effects of fen reclamation and elevated sulfate levels on mercury (Hg) fate and transport in the constructed system were assessed. Total mercury (THg) and methylmercury (MeHg) concentrations in the fen sediment were lower than in two nearby natural fens, which may be due to the higher mineral content of the Sandhill Fen peat mix and/or a loss of Hg through evasion during the peat harvesting, stockpiling and placement processes. Porewater MeHg concentrations in the Sandhill Fen typically did not exceed 1.0 ng L −1 . The low MeHg concentrations may be a result of elevated porewater sulfate concentrations (mean 346 mg L −1 ) and an increase in sulphide concentrations with depth in the peat, which are known to suppress MeHg production. Total Hg and MeHg concentrations increased during a controlled mid-summer flooding event where the water table rose above the ground surface in most of the fen. The Hg dynamics during this event showed that hydrologic fluctuations in this system exacerbate the release of THg and MeHg downstream. In addition, the elevated SO 4 2− concentrations in the peat porewaters may become a problem with respect to downstream MeHg production once the fen is hydrologically connected to a larger wetland network that is currently being constructed. - Highlights: • A constructed fen peatland in the Athabasca Oil Sands Region was studied. • Total and methyl mercury concentrations in fen sediment and waters

Dietary fish oil alters the lysophospholipid metabolomic profile and decreases urinary 11-dehydro thromboxane B₂ concentration in healthy Beagles.

Science.gov (United States)

Hall, Jean A; Brockman, Jeffrey A; Jewell, Dennis E

2011-12-15

Increased concentrations of dietary fish oil and antioxidants have been shown previously to change circulating concentrations of individual fatty acids (FAs) and vitamin E. The purpose of this study was to further investigate the effects of vitamins E and C, in combination with dietary fish oil, on selected blood and urinary biomarkers. Fifty adult Beagle dogs (mean age 5.3 years, range 1.4-14.2 years) were randomized into five dietary treatment groups for 90 days. All foods were complete and balanced and met the nutrient profiles of AAFCO for adult dogs. For 60 days before study initiation, dogs consumed a pretrial food that contained 74 IU/kg vitaminE and 0mg/kg vitaminC. The five experimental foods were confirmed by analytical methods to contain ≥ 640 IU/kg vitaminE and 130 mg/kg vitaminC (as fed). Experimental foods ranged from low levels of EPA and DHA (pretrial food and lowest experimental food had 0.01% EPA and no detectable DHA) to the highest experimental food with 0.25% EPA and 0.17% DHA. Serum was analyzed for FAs, vitamin E, and cholesterol concentrations; urine was analyzed for 11-dehydro thromboxane B(2) (TXB(2)). Serum was also used for metabolomic analysis. FA intake ranged from 0.02 g/day EPA and 0.02 g/day DHA to 0.58 g/day EPA and 0.39 g/day DHA. Increasing dietary concentrations of EPA and DHA resulted in increased serum concentrations of EPA and DHA in a dose-dependent fashion. Greater dietary vitamin E intake resulted in increased serum vitamin E concentrations (Pvitamin E concentrations (Pvitamin E concentration is enhanced primarily by feeding vitamin E and secondarily by serum cholesterol concentration. When feeding diets enriched with fish oil, the major negative predictor of urinary 11-dehydro TXB(2) concentration is serum EPA concentration. Plasma lysophospholipids can be dynamically regulated by dietary fish oil supplementation. Copyright © 2011 Elsevier B.V. All rights reserved.

Antioxidant, Anti-Tyrosinase and Anti-Inflammatory Activities of Oil Production Residues from Camellia tenuifloria

Directory of Open Access Journals (Sweden)

Shu-Yuan Chiou

2015-12-01

Full Text Available Camellia tenuifloria is an indigenous Camellia species used for the production of camellia oil in Taiwan. This study investigated for the first time the potential antioxidant, anti-tyrosinase and anti-inflammatory activities of oil production byproducts, specifically those of the fruit shell, seed shell, and seed pomace from C. tenuifloria. It was found that the crude ethanol extract of the seed shell had the strongest DPPH scavenging and mushroom tyrosinase inhibitory activities, followed by the fruit shell, while seed pomace was the weakest. The IC50 values of crude extracts and fractions on monophenolase were smaller than diphenolase. The phenolic-rich methanol fraction of seed shell (SM reduced nitric oxide (NO production, and inducible nitric oxide synthase (iNOS expression in lipopolysaccharide (LPS-stimulated RAW 264.7 cells. It also repressed the expression of IL-1β, and secretion of prostaglandin E2 (PGE2 and IL-6 in response to LPS. SM strongly stimulated heme oxygenase 1 (HO-1 expression and addition of zinc protoporphyrin (ZnPP, a HO-1 competitive inhibitor, reversed the inhibition of NO production, indicating the involvement of HO-1 in its anti-inflammatory activity. The effects observed in this study provide evidence for the reuse of residues from C. tenuifloria in the food additive, medicine and cosmetic industries.

Sustainable utilization of waste palm oil and sulfonated carbon catalyst derived from coconut meal residue for biodiesel production.

Science.gov (United States)

Thushari, Indika; Babel, Sandhya

2018-01-01

In this study, an inexpensive, environmental benign acid catalyst is prepared using coconut meal residue (CMR) and employed for biodiesel production from waste palm oil (WPO). The total acid density of the catalyst is found to be 3.8mmolg -1 . The catalyst shows a unique amorphous structure with 1.33m 2 g -1 of surface area and 0.31cm 3 g -1 of mean pore volume. Successful activation is confirmed by Fourier transform infrared (FT-IR) spectroscopy and X-ray photoelectron spectroscopy (XPS). The highest biodiesel yield of 92.7% was obtained from WPO in an open reflux system using the catalyst. Results show that biodiesel yield increases with increasing methanol:oil (molar ratio) and reaction time up to an optimum value. It is found that the catalyst can be reused for at least four cycles for >80% biodiesel yield. Fuel properties of the produced biodiesel meet international biodiesel standards. Copyright © 2017 Elsevier Ltd. All rights reserved.

Potential of glycerol and soybean oil for bioremediation of weathered oily-sludge contaminated soil

Energy Technology Data Exchange (ETDEWEB)

Nascimento, T.C.F.; Franca, F.P. [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil). Escola de Quimica], E-mail: fpfranca@eq.ufrj.br; Oliveira, F.J.S. [Petroleo Brasileiro S.A. (PETROBRAS), Rio de Janeiro, RJ (Brazil)

2012-04-15

The bioremediation of petroleum-contaminated soil was investigated on laboratory scale. This work evaluated the effect of co-substrate addition in tropical climate soil highly contaminated with oily residue. Glycerol and soybean oil were used as auxiliary co-substrates for contaminant degradation. Three different concentrations of co-substrate were tested, and the experiments were carried out over 60 days. The following parameters were monitored: humidity, pH, total heterotrophic bacteria, total fungi, total petroleum hydrocarbons (TPH), and the concentrations of benzo[a]pyrene and chrysene. The soil supplementation with renewable co-substrates improved the efficiency of the biodegradation TPH, with removals of 85% and 83% for glycerol and soybean oil, respectively, compared to a 55% removal yielded by the biodegradation process without supplementation. The use of glycerol increased Chrysene and Benzo[a]pyrene biodegradation by 50%, while soybean oil supplementation increased their removal by 36%. (author)

Petroleum hydrocarbon residues in the marine environment of Bassein-Mumbai

International Nuclear Information System (INIS)

Chouksey, M.K.; Kadam, A.N.; Zingde, M.D.

2005-01-01

The paper reports PHc contamination in water, sediment and biota of the coastal area of Bassein-Mumbai in relation to relatively less polluted sites (Dabhol and Ratnagiri) off the west coast of India. To facilitate inter-comparison three standards have been used though the results are reported in terms of SAM (Residue of Saudi Arabian Mix crude). The concentration of PHc in water off Bassein-Mumbai varies widely (2.9-39.2 μg l -1 ) as compared to the average baseline (2.8 μgl -1 ) with higher values generally confined to creeks and estuaries. The higher concentration of PHc in the bottom water of shallow areas is attributed to the contribution from the sediment-associated petroleum residue. High concentration of PHc in the surficial sediment of inshore area Ratnagiri (107.7 ppm, dry wt) is perhaps the remnants of an oil spill that occurred in the Bombay High region on May 17, 1993. The majority of values of PHc concentration in the surficial sediment of the Bassein-Mumbai region exceed 15 ppm (dry wt) against the expected background ( -1 respectively is estimated for cores U11 and U12. Substantial increase in the concentration of PHc in sediment after 1950 in cores T8 and T10 correlates well with the establishment of refineries on the western shore of the Thane Creek in 1955-1960. A minor peak in most cores in the top 10 cm sediment probably results from biological transfer of PHc lower into the sediment by benthic organisms. Excess of PHc retained in the sediment of the Bassein-Mumbai region over the biogenic background is estimated at 40,000 t. The PHc residues (1.8-10.8 ppm, wet wt) in fish caught off Bassein-Mumbai do not suggest bioaccumulation. (author)

The deep processing of oil residues conjunction with shales

Directory of Open Access Journals (Sweden)

Anatoly Maloletnev

2012-12-01

Full Text Available The results of studies on the development of a new process of thermal cracking of tar oil as a slurry with crushed oil shale to obtain components of motor fuels. The results suggest doubtless advantages of the process before the industrial of thermo cracking, since the single-stage processing of raw materials in relatively in the mild conditions (5 MPa, 425ºC, volumetric feed rate 1.0 h-1 is achieved deep destruction of tar oil (the yield petrol fraction with a bp amounts to up to 180ºC - ~12 mass % of middle distillates with a bp 180-360ºC – 43-44 mass %, of raw material for catalytic cracking of a bp 360-520ºC – ~15-16%, based on the initial tar oil. Formed like coke products and raw materials contained in V and Ni is postponed on the mineral part of slate and removed from the reaction zone with the liquid products of the process.

Oil supply and demand

International Nuclear Information System (INIS)

Rech, O.

2004-01-01

World oil demand, driven by economic development in China, posted the highest growth rate in 20 years. In a context of geopolitical uncertainty, prices are soaring, encouraged by low inventory and the low availability of residual production capacity. Will 2004 bring a change in the oil market paradigm? (author)

Oil supply and demand

Energy Technology Data Exchange (ETDEWEB)

Rech, O

2004-07-01

World oil demand, driven by economic development in China, posted the highest growth rate in 20 years. In a context of geopolitical uncertainty, prices are soaring, encouraged by low inventory and the low availability of residual production capacity. Will 2004 bring a change in the oil market paradigm? (author)

The H-Oil Process : Preferred configurations for application to western Canadian feedstocks

International Nuclear Information System (INIS)

Colyar, J.J.; Peer, E.D.

1997-01-01

The technical and economic evaluation of a method used to convert and upgrade petroleum residua and heavy oils into lighter products was described. The feasibility of applying the process to typical western Canadian oil sand feedstocks was evaluated. The H-Oil process, developed by HRI Inc., is an ebullated-bed catalytic hydrocracking process that accounts for more than 50 per cent of the worldwide vacuum residue hydroprocessing market. It has a unique flexibility to handle many different types of heavy crudes while producing clean transportation fuels. The unconverted vacuum residue from the process can be used for fuel oil production, blended into asphalt, or routed to a resid catalytic cracker or coker. The residue can also be directly combusted or gasified to produce hydrogen. Four different technologies that have been used commercially in Canada to upgrade western Canadian heavy oil residue have been reviewed and evaluated from a technical and economic viewpoint. The following improvements in the H-oil process have resulted in greater economy and product quality: (1) development of a new generation of high activity catalysts, (2) development of an improved recycle cup, and (3) new outlets for unconverted residue. It was suggested that the H-Oil process produces more revenue than the delayed coker process. As coke becomes harder to dispose of, the H-Oil process will become more attractive for producing synthetic crude from heavy oil. 6 refs., 9 tabs., 9 figs

Preparation of a Nanoemulsion with Carapa guianensis Aublet (Meliaceae Oil by a Low-Energy/Solvent-Free Method and Evaluation of Its Preliminary Residual Larvicidal Activity

Directory of Open Access Journals (Sweden)

Flávia L. M. Jesus

2017-01-01

Full Text Available Andiroba (Carapa guianensis seeds are the source of an oil with a wide range of biological activities and ethnopharmacological uses. However, few studies have devoted attention to innovative formulations, including nanoemulsions. The present study aimed to obtain a colloidal system with the andiroba oil using a low-energy and organic-solvent-free method. Moreover, the preliminary residual larvicidal activity of the nanoemulsion against Aedes aegypti was evaluated. Oleic and palmitic acids were the major fatty acids, in addition to the phytosterol β-sitosterol and limonoids (tetranortriterpenoids. The required hydrophile-lipophile was around 11.0 and the optimal nanoemulsion was obtained using polysorbate 85. The particle size distribution suggested the presence of small droplets (mean diameter around 150 nm and low polydispersity index (around 0.150. The effect of temperature on particle size distribution revealed that no major droplet size increase occurred. The preliminary residual larvicidal assay suggested that the mortality increased as a function of time. The present study allowed achievement of a potential bioactive oil in water nanoemulsion that may be a promising controlled release system. Moreover, the ecofriendly approach involved in the preparation associated with the great bioactive potential of C. guianensis makes this nanoemulsion very promising for valorization of this Amazon raw material.

The critical micelle concentration of lecithin in bulk oils and medium chain triacylglycerol is influenced by moisture content and total polar materials.

Science.gov (United States)

Kim, JiSu; Kim, Mi-Ja; Lee, JaeHwan

2018-09-30

Effects of different moisture contents and oxidised compounds on the critical micelle concentration (CMC) of lecithin were determined in bulk oils and in medium-chain triacylglycerols (MCT). CMC of lecithin in MCT was significantly higher than that in other vegetable oils including olive, soybean, corn, and rapeseed oils (p < 0.05). Presence of moisture significantly affected the CMC of lecithin in MCT (p < 0.05). CMC of lecithin was high when the moisture content was below 900 ppm, whereas at a moisture content of 1000 ppm, CMC of lecithin decreased significantly (p < 0.05), and then started to increase. Addition of total polar materials (TPM), which are oxidation products, at 3 and 5% concentrations, decreased CMC of lecithin significantly (p < 0.05) in MCT, compared to when 0, 1, and 1.5% of TPM was added to MCT. As the degree of oxidation increased in corn oil, CMC of lecithin gradually decreased. Additionally, under different moisture contents, corn oils showed a similar pattern of CMC of lecithin in MCT, whereas oxidised corn oil had a little lower CMC of lecithin than unoxidised corn oil. The results clearly showed that the concentration of lecithin for the formation of micelles is greatly influenced by the presence of oxidation products and the moisture content in bulk oils. Copyright © 2018 Elsevier Ltd. All rights reserved.

Evaluation of the toxicity of the weathered crude oil used at the Newfoundland Offshore Burn Experiment (NOBE) and the resultant burn residue

International Nuclear Information System (INIS)

Blenkinsopp, S.; Sergy, G.; Doe, K.; Wohlgeschaffen, G.; Li, K.; Fingas, M.

1997-01-01

Toxicity of the weathered crude oil Alberta Sweet Mixed Blend (ASMB) used at the Newfoundland Offshore Burn Experiment (NOBE), and the resultant burn residue was evaluated using the newly developed Environment Canada water-accomodated fraction (WAF) method and exposure protocol. Rainbow trout, three-spine stickleback and gametes of sea urchins were exposed to saltwater WAF prepared from both weathered ASMB and burn residue. Gas chromatography/ mass spectrometry headspace analysis of 28 analytes showed low levels of volatile hydrocarbons after 96 hours of exposure (except for sea urchins, in which case the test was only 20 minutes in duration). All samples were found to be not toxic to all species tested. 10 refs., 2 tabs

Decomposition of PCBs in transformer oil using an electron beam accelerator

Science.gov (United States)

Jung, In-Ha; Lee, Myun-Joo; Mah, Yoon-Jung

2012-07-01

Decomposition of PCBs in commercially used transformer oil used for more than 30 years has been carried out at normal temperature and pressure without any additives using an electron beam accelerator. The experiments were carried out in two ways: batch and continuous pilot plant with 1.5 MeV of energy, a 50 mA current, and 75 kW of power in a commercial scale accelerator. The electron beam irradiation seemed to transform large molecular weight compounds into lower ones, but the impact was considered too small on the physical properties of oil. Residual concentrations of PCBs after irradiation depend on the absorption dose of the electron beam energy, but aliphatic chloride compounds were produced at higher doses of irradiation. As the results from FT-NMR, chloride ions decomposed from the PCBs are likely to react with aliphatic hydro carbon compounds rather than existing as free radical ions in the transformer oil. Since this is a dry process, treated oil can be used as cutting oil or machine oil for heavy equipment without any additional treatments.

Plasma triacylglycerol and coagulation factor concentrations predict the anticoagulant effect of dietary fish oil in overweight subjects

DEFF Research Database (Denmark)

Vanschoonbeek, Kristof; Feijge, Marion A H; Saris, Wim H M

2007-01-01

fish-oil effects. In study 1, 54 overweight subjects consumed 3.1 g (n-3) PUFA daily. In study 2, which involved 42 overweight patients with type 2 diabetes, 20 subjects consumed (n-3) PUFA, whereas 22 others ingested a preparation rich in (n-6) PUFA. Tissue factor-induced thrombin generation (thrombin...... potential) was determined as an integrated measure of plasma coagulant activity. In both studies, multivariate analysis indicated a strong clustering of fasting concentrations of triacylglycerols, prothrombin, factor V, factor VII, and factor X with one another at baseline. This cluster of factors......-induced lowering of triacylglycerol and coagulation factor V, VII, and X concentrations, and thrombin generation. We conclude that high fasting triacylglycerol concentrations predict high procoagulant activity and a lowering of thrombin potential with dietary fish oil....

Properties of Residue from Olive Oil Extraction as a Raw Material for Sustainable Construction Materials. Part I: Physical Properties

Directory of Open Access Journals (Sweden)

Almudena Díaz-García

2017-01-01

Full Text Available Action on climate, the environment, and the efficient use of raw materials and resources are important challenges facing our society. Against this backdrop, the construction industry must adapt to new trends and environmentally sustainable construction systems, thus requiring lines of research aimed at keeping energy consumption in new buildings as low as possible. One of the main goals of this research is to efficiently contribute to reducing the amount of residue from olive oil extraction using a two-phase method. This can be achieved by producing alternative structural materials to be used in the construction industry by means of a circular economy. The technical feasibility of adding said residue to ceramic paste was proven by analyzing the changes produced in the physical properties of the paste, which were then compared to the properties of the reference materials manufactured with clay without residue. Results obtained show that the heating value of wet pomace can contribute to the thermal needs of the sintering process, contributing 30% of energy in pieces containing 3% of said material. Likewise, adding larger amounts of wet pomace to the clay body causes a significant decrease in bulk density values.

Properties of Residue from Olive Oil Extraction as a Raw Material for Sustainable Construction Materials. Part I: Physical Properties.

Science.gov (United States)

Díaz-García, Almudena; Martínez-García, Carmen; Cotes-Palomino, Teresa

2017-01-25

Action on climate, the environment, and the efficient use of raw materials and resources are important challenges facing our society. Against this backdrop, the construction industry must adapt to new trends and environmentally sustainable construction systems, thus requiring lines of research aimed at keeping energy consumption in new buildings as low as possible. One of the main goals of this research is to efficiently contribute to reducing the amount of residue from olive oil extraction using a two-phase method. This can be achieved by producing alternative structural materials to be used in the construction industry by means of a circular economy. The technical feasibility of adding said residue to ceramic paste was proven by analyzing the changes produced in the physical properties of the paste, which were then compared to the properties of the reference materials manufactured with clay without residue. Results obtained show that the heating value of wet pomace can contribute to the thermal needs of the sintering process, contributing 30% of energy in pieces containing 3% of said material. Likewise, adding larger amounts of wet pomace to the clay body causes a significant decrease in bulk density values.

Interpreting residues of petroleum hydrocarbons in wildlife tissues

International Nuclear Information System (INIS)

Hall, R.J.; Coon, N.C.

1988-08-01

This report is the first publication in the field of environmental-contaminant effects on wildlife to tell the reader how to interpret the results of analytical chemical results. Specifically, the publication describes how to interpret residues of petroleum hydrocarbons in wildlife tissues. Pollutant oil residues in avian species are emphasized

Protein-Protein Multilayer Oil-in-Water Emulsions for the Microencapsulation of Flaxseed Oil: Effect of Whey and Fish Gelatin Concentration.

Science.gov (United States)

Fustier, Patrick; Achouri, Allaoua; Taherian, Ali R; Britten, Michel; Pelletier, Marylène; Sabik, Hassan; Villeneuve, Sébastien; Mondor, Martin

2015-10-28

The impact of whey protein isolate (WPI) and fish gelatin (FG) deposited sequentially at concentrations of 0.1, 0.5, and 0.75% on the surface of primary oil-in-water emulsions containing 5% flaxseed oil stabilized with either 0.5% fish gelatin or whey protein, respectively, was investigated. The results revealed that the adsorption of WPI/FG or FG/WPI complexes to the emulsion interface led to the formation of oil-in-water (o/w) emulsions with different stabilities and different protection degrees of the flaxseed oil. Deposition of FG on the WPI primary emulsion increased the particle size (from 0.53 to 1.58 μm) and viscosity and decreased electronegativity (from -23.91 to -11.15 mV) of the complexes. Different trends were noted with the deposition of WPI on the FG primary emulsion, resulting in decreasing particle size and increasing electronegativity and viscosity to a lower extent. Due to the superior tension-active property of WPI, the amount of protein load in the WPI primary emulsion as well as in WPI/FG complex was significantly higher than the FG counterparts. A multilayer emulsion made with 0.5% WPI/0.75% FG exhibited the lowest oxidation among all of the multilayered emulsions tested (0.32 ppm of hexanal) after 21 days, likely due to the charge effect of FG that may prevent pro-oxidant metals to interact with the flaxseed oil.

Numerical approach for enhanced oil recovery with surfactant flooding

Directory of Open Access Journals (Sweden)

Sadegh Keshtkar

2016-03-01

Full Text Available The remained oil in the reservoir after conventional water-flooding processes, forms a dispersed phase in the form of oil drops which is trapped by capillary forces and is almost about 70% of the original oil in the place (OOIP. To reduce oil residual saturation in laboratory experiments and field projects, surfactant flooding is effective via decreasing the interfacial tension mobility ratio between oil and water phases. Estimation of the role of design variables, like chemical concentrations, partition coefficient and injection rate in different performance quantities, considering a heterogeneous and multiphase oil reservoir is a critical stage for optimal design. Increasing demand for oil production from water-flooded reservoirs has caused an increasing interest in surfactant-polymer (SP and alkali-surfactant-polymer (ASP. Modeling minimizes the risk of high cost of chemicals by improving our insight of process. In the present paper, a surfactant compositional flood model for a three-component (water, petroleum and surfactant, two phase (aqueous and oleic system is studied. A homogeneous, two-dimensional, isothermal reservoir with no free gas or alkali is assumed. The governing equations are in three categories: the continuity equations for the transport of each component, Darcy's equation for the transport of each phase and other auxiliary equations. The equations are solved by finite-differences using a procedure implicit in pressure and explicit in saturation. The validation of the model is achieved through comparing the modeling results with CMG simulators and Buckley–Leverett theory. The results of modeling showed good agreement with CMG results, and the comparison with Buckley–Leverett theory is explained according to different assumptions. After validation of the model, in order to investigate sensitivity analysis, the effects of system variables (partition coefficient, surface tension, oil viscosity and surface injection

Radon Concentration in Outdoors and Indoors Around the Flare in Oil Mine Sites

International Nuclear Information System (INIS)

Sutarman; Wahyudi; Luhantara

2003-01-01

The flares are much found at the oil exploration areas which appear the combustion gases emission to the environment that pass through a pipe at about 8 m high from the ground level. The flare is released into the environment together with the hydrocarbon and radon gases. This study has been carried out the measurement of the radon gas concentration only. Radon is a radioactive gas which comes from the natural radioactive decay of uranium ( 238 U). The outdoor radon concentrations were measured in 23 locations with the two-filter method. The locations were determined by a circle which the flare as the point center. The outdoor radon concentrations were measured in 74 houses (more than distance of 600 m from the flare) with the alpha track detector (CR-39) placed in the living rooms for about three months. The measurements of the radon concentrations were carried out in Cepu, Cirebon, and Prabumulih oil mine sites. The results showed that the outdoor radon concentrations a range of 108 Bq/m 3 to 256 Bq/m 3 in Cepu, 248 Bq/m 3 to 3525 Bq/m 3 in Cirebon, and 51 Bq/m 3 to 114 Bq/m 3 in Prabumulih. The results showed that the indoor radon concentrations a range of 11 Bq/m 3 to 38 Bq/m 3 in Cepu, 28 Bq/m 3 to 184 Bq/m 3 in Cirebon, and 12 Bq/m 3 to 38 Bq/m 3 in Prabumulih. The data of the maximum radon concentration in outdoor air was higher than an actual level which recommended by International Atomic Energy Agency (IAEA) for workplaces. The maximum radon concentration in indoor air was lower than an actual level which recommended by IAEA for dwellings. IAEA recommends the actual level of 1000 Bq/m 3 for workplaces and 200 Bq/m 3 for dwellings. These data will be used for the baseline data of the environmental radioactivity in Indonesia. (author)

Influence of pretreatment of agriculture residues on phytase ...

African Journals Online (AJOL)

phytase production. Pretreatment of agriculture residues with water to remove excess inorganic phosphate has significantly enhanced the phytase activity in case of de-oiled rice bran, wheat bran, peanut cake (low and high oil) and coconut cake. Maximum increase of 20.3 times in phytase activity was observed in case of ...

Sun drying of residual annatto seed powder

Directory of Open Access Journals (Sweden)

Dyego da Costa Santos

2015-01-01

Full Text Available Residual annatto seeds are waste from bixin extraction in the food, pharmaceutical and cosmetic industries. Most of this by-product is currently discarded; however, the use of these seeds in human foods through the elaboration of powder added to other commercial powders is seen as a viable option. This study aimed at drying of residual annatto powder, with and without the oil layer derived from the industrial extraction of bixin, fitting different mathematical models to experimental data and calculating the effective moisture diffusivity of the samples. Powder containing oil exhibited the shortest drying time, highest drying rate (≈ 5.0 kg kg-1 min-1 and highest effective diffusivity (6.49 × 10-12 m2 s-1. All mathematical models assessed were a suitable representation of the drying kinetics of powders with and without oil, with R2 above 0.99 and root mean square error values lower than 1.0.

Management of industrial solid residues; Gerenciamento de residuos solidos industriais

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-07-01

This chapter gives an overview on the management of industrial solid wastes, approaching the following subjects: classification of industrial solid residues; directives and methodologies for the management of industrial solid residues; instruments for the management of industrial solid residues; handling, packing, storage and transportation; treatment of industrial solid residues; final disposal - landfill for industrial residues; the problem of treatment and final disposer of domestic garbage in Brazil; recycling of the lubricant oils used in brazil; legislation.

[Development of a portable mid-infrared rapid analyzer for oil concentration in water based on MEMS linear sensor array].

Science.gov (United States)

Gao, Zhi-fan; Zeng, Li-bo; Shi, Lei; Li, Kai; Yang, Yuan-zhou; Wu, Qiong-shui

2014-06-01

Aiming at the existing problems such as weak environmental adaptability, low analytic efficiency and poor measuring repeatability in the traditional spectral oil analyzers, the present paper designed a portable mid-infrared rapid analyzer for oil concentration in water. To reduce the volume of the instrument, the non-symmetrical folding M-type Czerny-Turner optical structure was adopted in the core optical path. With a periodically rotating chopper, controlled by digital PID algorithm, applied for infrared light modulation, the modulating accuracy reached ±0.5%. Different from traditional grating-scanning spectrophotometers, this instrument used a fixed grating for light dispersion and avoided rotating error in the course of the measuring procedures. A new-type MEMS infrared linear sensor array was applied for modulated spectral signals detection, which improved the measuring efficiency remarkably. Optical simulation and experimental results indicate that the spectral range is 2 800 - 3 200 cm(-1), the spectral resolution is 6 cm(-1) (@3 130 cm(-1)), and the signal to noise ratio is up to 5 200 : 1. The acquisition time is 13 milliseconds per spectrogram, and the standard deviation of absorbance is less than 3 x 10(-3). These performances meet the standards of oil concentration measurements perfectly. Compared with traditional infrared spectral analyzers for oil concentration, the instrument demonstrated in this paper has many advantages such as smaller size, more efficiency, higher precision, and stronger vibration & moisture isolation. In addition, the proposed instrument is especially suitable for the environmental monitoring departments to implement real-time measurements in the field for oil concentration in water, hence it has broad prospects of application in the field of water quality monitoring.

ASEAN grid-connected biomass residues fired cogeneration plants

International Nuclear Information System (INIS)

Adnan, M.F.; Alias, R.

2006-01-01

Energy supply is one of the major concerns in the world. With uncertainty in the main oil suppliers, the oil price is expected to remain high due to continuous demand from the world. Since oil is mostly used for electricity and transportation, its shortage would cause major disruptions in our daily activities. Thus to counter this scenario and faster depletion of fossil fuel resources, various measures have been taken to find alternative source of energy such as renewable energy. One of the renewable energy sources is from biomass residues which is aplenty particularly in ASEAN. Through one of the collaboration programme between ASEAN and EC which is The EC-ASEAN Cogeneration Programme, a number of Full-Scale Demonstration Projects (FSDP) using biomass residues have been commissioned and implemented successfully. Four of the FSDPs in Thailand and Malaysia are connected to the grid. These projects have been operating very well and since the fuel is commonly available in this ASEAN region, duplication should not be a problem. Thus, this paper would highlight the success stories in implementing biomass residues grid connected project while enhancing cooperation between ASEAN and EC. (Author)

Thermal Adsorption Processing Of Hydrocarbon Residues

Directory of Open Access Journals (Sweden)

Sudad H. Al.

2017-04-01

Full Text Available The raw materials of secondary catalytic processes must be pre-refined. Among these refining processes are the deasphalting and demetallization including their thermo adsorption or thermo-contact adsorption variety. In oil processing four main processes of thermo-adsorption refining of hydrocarbon residues are used ART Asphalt Residual Treating - residues deasphaltizing 3D Discriminatory Destructive Distillation developed in the US ACT Adsorption-Contact Treatment and ETCC Express Thermo-Contact Cracking developed in Russia. ART and ACT are processes with absorbers of lift type reactor while 3D and ETCC processes are with an adsorbing reactor having ultra-short contact time of the raw material with the adsorbent. In all these processes refining of hydrocarbon residues is achieved by partial Thermo-destructive transformations of hydrocarbons and hetero-atomic compounds with simultaneous adsorption of the formed on the surface of the adsorbents resins asphaltene and carboids as well as metal- sulphur - and nitro-organic compounds. Demetallized and deasphalted light and heavy gas oils or their mixtures are a quality raw material for secondary deepening refining processes catalytic and hydrogenation cracking etc. since they are characterized by low coking ability and low content of organometallic compounds that lead to irreversible deactivation of the catalysts of these deepening processes.

Recovery of transuranics from process residues

International Nuclear Information System (INIS)

Gray, J.H.; Gray, L.W.

1987-01-01

Process residues are generated at both the Rocky Flats Plant (RFP) and the Savannah River Plant (SRP) during aqueous chemical and pyrochemical operations. Frequently, process operations will result in either impure products or produce residues sufficiently contaminated with transuranics to be nondiscardable as waste. Purification and recovery flowsheets for process residues have been developed to generate solutions compatible with subsequent Purex operations and either solid or liquid waste suitable for disposal. The ''scrub alloy'' and the ''anode heel alloy'' are examples of materials generated at RFP which have been processed at SRP using the developed recovery flowsheets. Examples of process residues being generated at SRP for which flowsheets are under development include LECO crucibles and alpha-contaminated hydraulic oil

Development of More Effective Biosurfactants for Enhanced Oil Recovery

Energy Technology Data Exchange (ETDEWEB)

McInerney, J.J.; Han, S.O.; Maudgalya, S.; Mouttaki, H.; Folmsbee, M.; Knapp, R.; Nagle, D.; Jackson, B.E.; Stuadt, M.; Frey, W.

2003-01-16

The objectives of this were two fold. First, core displacement studies were done to determine whether microbial processes could recover residual oil at elevated pressures. Second, the importance of biosurfactant production for the recovery of residual oil was studies. In these studies, a biosurfactant-producing, microorganisms called Bacillus licheniformis strain JF-2 was used. This bacterium produces a cyclic peptide biosurfactant that significantly reduces the interfacial tension between oil and brine (7). The use of a mutant deficient in surfactant production and a mathematical MEOR simulator were used to determine the major mechanisms of oil recovery by these two strains.

Joint ventures and concentrations in oil market

International Nuclear Information System (INIS)

Tabarelli, D.

1996-01-01

Many are the joint ventures taken during last year by the oil companies as a move towards the ever existing rules of the oil market: integration, economies of scale and reduction of competitive market uncertainty. This article discusses some of the most interesting points of the recent events and the initiatives in the Italian market

Liquid oil and residual characteristics of printed circuit board recycle by pyrolysis

Energy Technology Data Exchange (ETDEWEB)

Lin, Kuo-Hsiung [Department of Environmental Engineering and Science, Fooyin University, Kaohsiung, Taiwan (China); Chiang, Hung-Lung, E-mail: hlchiang@mail.cmu.edu.tw [Department of Health Risk Management, China Medical University, Taichung, Taiwan (China)

2014-04-01

Highlights: • Pyrolysis is a technology for recycling of the non-metal fraction of PCBs. • Liquid product constituents were analyzed for PCB pyrolysis. • Water-soluble ionic species were determined for PCB pyrolysis exhaust. - Abstract: Non-metal fractions of waste printed circuit boards (PCBs) were thermally treated (200–500 °C) under nitrogen atmosphere. Carbon, hydrogen, and nitrogen were determined by elemental analyzer, bromine by instrumental neutron activation analysis (INAA), phosphorus by energy dispersive X-ray spectrometer (EDX), and 29 trace elements by inductively coupled plasma atomic emission spectrometer (ICP-AES) and mass spectrometry (ICP-MS) for raw material and pyrolysis residues. Organic compositions of liquid oil were identified by GC (gas chromatography)–MS, trace element composition by ICP system, and 12 water-soluble ions by IC (ionic chromatography). Elemental content of carbon was >450 mg/g, oxygen 300 mg/g, bromine and hydrogen 60 mg/g, nitrogen 30 mg/g, and phosphorus 28 mg/g. Sulfur was trace in PCBs. Copper content was 25–28 mg/g, iron 1.3–1.7 mg/g, tin 0.8–1.0 mg/g and magnesium 0.4–1.0 mg/g; those were the main metals in the raw materials and pyrolytic residues. In the liquid products, carbon content was 68–73%, hydrogen was 10–14%, nitrogen was 4–5%, and sulfur was less than 0.05% at pyrolysis temperatures from 300 to 500 °C. Phenol, 3-bromophenol, 2-methylphenol and 4-propan-2-ylphenol were major species in liquid products, accounting for >50% of analyzed organic species. Bromides, ammonium and phosphate were the main species in water sorption samples for PCB pyrolysis exhaust.

Soils washing for removal of heavy oil: Naval Air Engineering Center, Lakehurst, NJ

International Nuclear Information System (INIS)

Nash, J.H.; Traver, R.P.

1991-01-01

With the recognition that large tracts of land are currently unusable as a result of either accidental spills or past industrial practices (such as oil field development), the USEPA Office of Research and Development evaluated soil washing as an alternative remedial technology for heavy oil contaminated soil at a site located on the Naval Air Engineering Center (NAEC), Lakehurst, New Jersey. The researchers used a self-contained, 100-pound-per-hour soil washer. Electrical, pneumatic, and fluid-pumping capabilities were provided by the trailer-mounted system at a remote No. 6 type oil spill site at the Navy base. Chloroform extracts of the contaminated sandy soil recovered a 0.91 gram/milliliter, 950 centistoke viscosity, dark brown, non-PCB oil. By using a surfactant/solvent solution at ambient temperatures, contaminant levels on the soil were reduced from 3.8% (38,000 milligram/kilogram-RCRA hazardous waste designation) to as low as 0.035% (350 milligram/kilogram) oil concentration. Supplemental laboratory evaluations extending the pilot field evaluations showed at elevated temperatures (120F) that residual oil contamination was less than 0.01% (100 milligram/kilogram). This final oil concentration in the treated soil would be defined as clean under the New Jersey Environmental Cleanup and Responsibilities Act (ECRA). A continuous belt press filter was used to recover the oil in a 47% solids cake that could be used as a secondary fuel feed to a waste boiler. The wash water solution was treated and recycled permitting economical operations

Comparative evaluation of thermal oxidative decomposition for oil-plant residues via thermogravimetric analysis: Thermal conversion characteristics, kinetics, and thermodynamics.

Science.gov (United States)

Chen, Jianbiao; Wang, Yanhong; Lang, Xuemei; Ren, Xiu'e; Fan, Shuanshi

2017-11-01

Thermal oxidative decomposition characteristics, kinetics, and thermodynamics of rape straw (RS), rapeseed meal (RM), camellia seed shell (CS), and camellia seed meal (CM) were evaluated via thermogravimetric analysis (TGA). TG-DTG-DSC curves demonstrated that the combustion of oil-plant residues proceeded in three stages, including dehydration, release and combustion of organic volatiles, and chars oxidation. As revealed by combustion characteristic parameters, the ignition, burnout, and comprehensive combustion performance of residues were quite distinct from each other, and were improved by increasing heating rate. The kinetic parameters were determined by Coats-Redfern approach. The results showed that the most possible combustion mechanisms were order reaction models. The existence of kinetic compensation effect was clearly observed. The thermodynamic parameters (ΔH, ΔG, ΔS) at peak temperatures were calculated through the activated complex theory. With the combustion proceeding, the variation trends of ΔH, ΔG, and ΔS for RS (RM) similar to those for CS (CM). Copyright © 2017 Elsevier Ltd. All rights reserved.

Total lead (Pb) concentration in oil shale ash samples based on correlation to isotope Pb-210 gamma-spectrometric measurements

Energy Technology Data Exchange (ETDEWEB)

Vaasma, T.; Kiisk, M.; Tkaczyk, A.H. [University of Tartu (Estonia); Bitjukova, L. [Tallinn University of Technology (Estonia)

2014-07-01

Estonian oil shale consists of organic matter and mineral material and contains various amounts of heavy metals as well as natural radionuclides (from the U-238 and Th-232 series and K-40). Previous research has shown that burning oil shale in the large power plants causes these radionuclides to become enriched in different ash fractions and be partially emitted to the atmosphere via fly ash and flue gases. The activity concentrations (Bq/kg) of these nuclides in different oil shale ash fractions vary significantly. This is influenced by the boiler parameters and combustion conditions - prevailing temperatures, pressure, ash circulating mechanisms, fly ash particle size, chemical composition of ash and coexistence of macro and micro components. As with radionuclides, various heavy metals remain concentrated in the ash fractions and are released to the atmosphere (over 20 tons of Pb per year from Estonian oil shale power plants). Lead is a heavy metal with toxic influence on the nervous system, reproductive system and different organs in human body. Depending on the exposure pathways, lead could pose a long term health hazard. Ash samples are highly heterogeneous and exhibit great variability in composition and particle size. Determining the lead concentration in ash samples by modern methods like inductively coupled plasma mass spectroscopy (ICP-MS), flame atomic absorption spectrometry (FAAS), graphite furnace atomic absorption spectroscopy (GFAAS) and other techniques often requires time consuming, multistage and complex chemical sample preparation. The list of possible methods to use is lengthy, but it is a challenge to choose a suitable one to meet measurement needs and practical considerations. The detection limits, capital costs and maintenance expenses vary between the instruments. This work presents the development of an alternative measurement technique for our oil shale ash samples. Oil shale ash was collected from different boilers using pulverized fuel

Development of Bottom Oil Recovery Systems. Revised

Science.gov (United States)

2014-02-01

ahead of the filtration process. Stage 6 Disposal: Collection of oil , oiled debris, and decontaminated sand/sediments. 7 NET ENVIRONMENTAL BENEFIT......Sea HFO / 10.7 X 1983 T/V Hanon Jade Yosu, South Korea Heavy Arabian Crude Oil X (salt) ( burn residue) 1984 T/V Alvenus Louisiana Merey

Raman spectroscopy for the evaluation of the effects of different concentrations of Copper on the chemical composition and biological activity of basil essential oil

Science.gov (United States)

Nawaz, Haq; Hanif, Muhammad Asif; Ayub, Muhammad Adnan; Ishtiaq, Faiqa; Kanwal, Nazish; Rashid, Nosheen; Saleem, Muhammad; Ahmad, Mushtaq

2017-10-01

The present study is performed to evaluate the effect of different concentrations of Cu as fertilizer on the chemical composition of basil essential oil and its biological activity including antioxidant and antifungal activities by employing Raman spectroscopy. Moreover, the effect of Cu is also determined on the vegetative growth and essential oil yield. Both, antifungal and antioxidant activities were found to be maximum with essential oils obtained at 0.04 mg/l concentration of Cu fertilizer. The results of the GC-MS and Raman spectroscopy have revealed that the linalool and estragole are found to be as a major chemical compound in basil essential oil. The Raman spectral changes associated with these biological components lead to the conclusion that estragole seems to have dominating effect in the biological activities of the basil essential oil as compared to linalool although the latter is observed in greater concentration.

Hydrocarbon oils

Energy Technology Data Exchange (ETDEWEB)

Foorwood, G F; Taplay, J G

1916-12-12

Hydrocarbon oils are hydrogenated, cracked, or treated for the removal of sulfur by bringing their vapors mixed with steam at temperatures between 450 and 600/sup 0/C into contact with a form of carbon that is capable of decomposing steam with the production of nascent hydrogen at those temperatures. The forms of carbon used include lamp-black, soot, charcoals derived from wood, cellulose, and lignite, and carbons obtained by carbonizing oil residues and other organic bodies at temperatures below 600/sup 0/C. The process is applied to the treatment of coal oil, shale oil, petroleum, and lignite oil. In examples, kerosene is cracked at 570/sup 0/C, cracked spirit is hydrogenated at 500/sup 0/C, and shale spirit is desulfurized at 530/sup 0/C. The products are led to a condenser and thence to a scrubber, where they are washed with creosote oil. After desulfurization, the products are washed with dilute caustic soda to remove sulfurretted hydrogen.

Monitoring polycyclic aromatic hydrocarbon pollution in the marine environment after the Prestige oil spill by means of seabird blood analysis.

Science.gov (United States)

Pérez, Cristóbal; Velando, Alberto; Munilla, Ignacio; López-Alonso, Marta; Oro, Daniel

2008-02-01

In this study we tested the use of seabird blood as a bioindicator of polycyclic aromatic hydrocarbon (PAH) pollution in the marine environment. Blood cells of breeding yellow-legged gulls (Larus michahellis) were able to track spatial and temporal changes consistent with the massive oil pollution pulse that resulted from the Prestige oil spill. Thus, in 2004, blood samples from yellow-legged gulls breeding in colonies that were in the trajectory of the spill doubled in theirtotal PAH concentrations when compared to samples from unoiled colonies. Furthermore, PAH levels in gulls from an oiled colony decreased by nearly a third in two consecutive breeding seasons (2004 and 2005). Experimental evidence was gathered by means of an oil-ingestion field experiment. The total concentration of PAHs in the blood of gulls given oil supplements was 30% higher compared to controls. This strongly suggested that measures of PAHs in the blood of gulls are sensitive to the ingestion of small quantities of oil. Our study provides evidence that seabirds were exposed to residual Prestige oil 17 months after the spill commenced and gives support to the nondestructive use of seabirds as biomonitors of oil pollution in marine environments.

Effects of fish oil replacement and re-feeding on the bioaccumulation of organochlorine compounds in gilthead sea bream (Sparus aurata L.) of market size.

Science.gov (United States)

Nácher-Mestre, Jaime; Serrano, Roque; Benedito-Palos, Laura; Navarro, Juan C; López, Francisco J; Pérez-Sánchez, Jaume

2009-08-01

Organochlorine pesticide residues and polychlorinated biphenyls were determined in raw materials, fish feeds and fillets from fish exposed through the productive cycle (14 months) to experimental diets with different percentages of fish oil replacement with vegetable oils. Detectable amounts of organochlorine compounds were found in raw materials derived from fish sources with none being detected in vegetable ingredients. Fish feeds presented trace concentrations of contaminants at the ng/g level, which varied according to the contribution of the different resources used in their manufacture. Contaminants did not accumulate during the first 11 months of exposure, and low concentrations of organochlorine compounds were found both at the start and at the end of this feeding period. Fillets from fish fed the fish oil diet presented the highest concentrations of organochlorine compounds, with these decreasing in proportion to fish oil replacement. Three months of fish oil re-feeding during the finishing phase only produced significant bioaccumulation over the course of the first month. By optimizing fish meal and fish oil replacement with vegetable oils alternative feeds can contribute to significantly reduce the risk of organochlorine uptake by consumers.

Application of preservatives for residual fuels

International Nuclear Information System (INIS)

Gorozpe y Munoz, Tomas

2000-01-01

Due to the high costs of the combust oils (fuel oil 6) used in generators of vapor and in other treatments, makes important consider the use of preservatives that improve the operation of the units from the operative point of view and of environmental control. The author enumerates several of the problems of corrosion, of efficiency in the combustion and of thermal efficiency; in a same way it enumerates several useful preservatives, to be used in residual fuel

Agrochemical characterization of vermicomposts produced from residues of Palo Santo (Bursera graveolens) essential oil extraction.

Science.gov (United States)

Carrión-Paladines, Vinicio; Fries, Andreas; Gómez-Muñoz, Beatriz; García-Ruiz, Roberto

2016-12-01

Fruits of Palo Santo (Bursera graveolens) are used for essential oil extraction. The extraction process is very efficient, because up to 3% of the fresh fruits can be transformed into essential oil; however, a considerable amount of waste is concurrently produced (>97% of the fresh biomass). Recent developments in Ecuadorian policies to foster environmentally friendly agroforestry and industrial practices have led to widespread interest in reusing the waste. This study evaluated the application of four vermicomposts (VMs), which are produced from the waste of the Palo Santo fruit distillation in combination with other raw materials (kitchen leftovers, pig manure, goat manure, and King Grass), for agrochemical use and for carbon (C) and nitrogen (N) decomposition in two soils with different textures. The results showed that the vermicompost mixtures (VMM) were valuable for agricultural utilisation, because total N (min. 2.63%) was relatively high and the C/N ratio (max. 13.3), as well as the lignin (max. 3.8%) and polyphenol (max. 1.6%) contents were low. In addition, N availability increased for both soil types after the application of the VMM. In contrast, N became immobile during decomposition if the VM of the pure waste was added. This likely occurred because of the relatively low total N (1.16%) content and high C/N ratio (35.0). However, the comparatively low C decomposition of this VM type makes its application highly recommendable as a strategy to increase the levels of organic matter and C, as well as for soil reclamation. Overall, these results suggest that the residues of the Palo Santo essential oil extraction are a potential source for vermicompost production and sustainable agriculture. Copyright © 2016 Elsevier Ltd. All rights reserved.

Vaporization order and burning efficiency of crude oils during in-situ burning on water

DEFF Research Database (Denmark)

van Gelderen, Laurens; Malmquist, Linus M.V.; Jomaas, Grunde

2017-01-01

furthermore showed that the vaporization was diffusion-limited. Analysis of the heat transfer balance for the crude oils indicated that the energy available for evaporation decreased over time due to increasing heat losses, which were caused by the volatility controlled vaporization order. Presumably, larger......In order to improve the understanding of the burning efficiency and its observed size dependency of in-situ burning of crude oil on water, the vaporization order of the components in crude oils was studied. The vaporization order of such multicomponent fuels was assessed by studying the surface...... these results. The crude oils did not show any steady state behavior, but instead had an increasing surface temperature and decreasing burning rate and flame height, indicating a volatility controlled vaporization order. An increasing concentration gradient from the medium to heavy fraction in the burn residues...

Revitalizing a mature oil play: Strategies for finding and producing unrecovered oil in frio fluvial-deltaic sandstone reservoirs at South Texas. Annual report, October 1994--October 1995

Energy Technology Data Exchange (ETDEWEB)

Holtz, M.; Knox, P.; McRae, L. [and others

1996-02-01

The Frio Fluvial-Deltaic Sandstone oil play of South Texas has produced nearly 1 billion barrels of oil, yet it still contains about 1.6 billion barrels of unrecovered mobile oil and nearly the same amount of residual oil resources. Interwell-scale geologic facise models of Frio Fluvial-deltaic reservoirs are being combined with engineering assessments and geophysical evaluations in order to determine the controls that these characteristics exert on the location and volume or unrecovered mobile and residual oil. Progress in the third year centered on technology transfer. An overview of project tasks is presented.

Dual-Polarized L-Band SAR Imagery for Temporal Monitoring of Marine Oil Slick Concentration

Directory of Open Access Journals (Sweden)

Sébastien Angelliaume

2018-06-01

Full Text Available SAR sensors are usually used in the offshore domain to detect marine oil slicks which allows the authorities to guide cleanup operations or prosecute polluters. As radar imagery can be used any time of day or year and in almost any weather conditions, the use and programming of such remote sensing data is usually favored over optical imagery. Nevertheless, images collected in the optical domain provide access to key information not accessible today by SAR instruments, such as the thickness or the amount of pollutant. To address this knowledge gap, a methodology based on the joint use of a scattering model (U-WCA and remote sensing data collected by a low frequency (e.g., L-band imaging radar over controlled release of mineral oil spill is reported in this paper. The proposed method allows estimation of the concentration of pollutant within an oil-in-water mixture as well as the temporal variation of this quantity due to weathering processes.

Rapid detection of chlorpyrifos pesticide residue concentration in agro-product using Raman spectroscopy

Science.gov (United States)

Dhakal, Sagar; Peng, Yankun; Li, Yongyu; Chao, Kuanglin; Qin, Jianwei; Zhang, Leilei; Xu, Tianfeng

2014-05-01

Different chemicals are sprayed in fruits and vegetables before and after harvest for better yield and longer shelf-life of crops. Cases of pesticide poisoning to human health are regularly reported due to excessive application of such chemicals for greater economic benefit. Different analytical technologies exist to detect trace amount of pesticides in fruits and vegetables, but are expensive, sample destructive, and require longer processing time. This study explores the application of Raman spectroscopy for rapid and non-destructive detection of pesticide residue in agricultural products. Raman spectroscopy with laser module of 785 nm was used to collect Raman spectral information from the surface of Gala apples contaminated with different concentrations of commercially available organophosphorous (48% chlorpyrifos) pesticide. Apples within 15 days of harvest from same orchard were used in this study. The Raman spectral signal was processed by Savitzky-Golay (SG) filter for noise removal, Multiplicative Scatter Correction (MSC) for drift removal and finally polynomial fitting was used to eliminate the fluorescence background. The Raman spectral peak at 677 cm-1 was recognized as Raman fingerprint of chlorpyrifos. Presence of Raman peak at 677 cm-1 after fluorescence background removal was used to develop classification model (presence and absence of pesticide). The peak intensity was correlated with actual pesticide concentration obtained using Gas Chromatography and MLR prediction model was developed with correlation coefficient of calibration and validation of 0.86 and 0.81 respectively. Result shows that Raman spectroscopy is a promising tool for rapid, real-time and non-destructive detection of pesticide residue in agro-products.

Alkaline hydrothermal liquefaction of swine carcasses to bio-oil

Energy Technology Data Exchange (ETDEWEB)

Zheng, Ji-Lu, E-mail: triace@163.com; Zhu, Ming-Qiang; Wu, Hai-tang

2015-09-15

Highlights: • Swine carcasses can be converted to bio-oil by alkaline hydrothermal liquefaction. • It seems that the use of the bio-oil for heat or CHP is technically suitable. • Some valuable chemicals were found in the bio-oils. • The bio-oil and the solid residue constituted an energy efficiency of 93.63% for the feedstock. • The solid residue can be used as a soil amendment, to sequester C and for preparing activated carbon. - Abstract: It is imperative that swine carcasses are disposed of safely, practically and economically. Alkaline hydrothermal liquefaction of swine carcasses to bio-oil was performed. Firstly, the effects of temperature, reaction time and pH value on the yield of each liquefaction product were determined. Secondly, liquefaction products, including bio-oil and solid residue, were characterized. Finally, the energy recovery ratio (ERR), which was defined as the energy of the resultant products compared to the energy input of the material, was investigated. Our experiment shows that reaction time had certain influence on the yield of liquefaction products, but temperature and pH value had bigger influence on the yield of liquefaction products. Yields of 62.2 wt% bio-oil, having a high heating value of 32.35 MJ/kg and a viscosity of 305cp, and 22 wt% solid residue were realized at a liquefaction temperature of 250 °C, a reaction time of 60 min and a pH value of 9.0. The bio-oil contained up to hundreds of different chemical components that may be classified according to functional groups. Typical compound classes in the bio-oil were hydrocarbons, organic acids, esters, ketones and heterocyclics. The energy recovery ratio (ERR) reached 93.63%. The bio-oil is expected to contribute to fossil fuel replacement in stationary applications, including boilers and furnaces, and upgrading processes for the bio-oil may be used to obtain liquid transport fuels.

Alkaline hydrothermal liquefaction of swine carcasses to bio-oil

International Nuclear Information System (INIS)

Zheng, Ji-Lu; Zhu, Ming-Qiang; Wu, Hai-tang

2015-01-01

Highlights: • Swine carcasses can be converted to bio-oil by alkaline hydrothermal liquefaction. • It seems that the use of the bio-oil for heat or CHP is technically suitable. • Some valuable chemicals were found in the bio-oils. • The bio-oil and the solid residue constituted an energy efficiency of 93.63% for the feedstock. • The solid residue can be used as a soil amendment, to sequester C and for preparing activated carbon. - Abstract: It is imperative that swine carcasses are disposed of safely, practically and economically. Alkaline hydrothermal liquefaction of swine carcasses to bio-oil was performed. Firstly, the effects of temperature, reaction time and pH value on the yield of each liquefaction product were determined. Secondly, liquefaction products, including bio-oil and solid residue, were characterized. Finally, the energy recovery ratio (ERR), which was defined as the energy of the resultant products compared to the energy input of the material, was investigated. Our experiment shows that reaction time had certain influence on the yield of liquefaction products, but temperature and pH value had bigger influence on the yield of liquefaction products. Yields of 62.2 wt% bio-oil, having a high heating value of 32.35 MJ/kg and a viscosity of 305cp, and 22 wt% solid residue were realized at a liquefaction temperature of 250 °C, a reaction time of 60 min and a pH value of 9.0. The bio-oil contained up to hundreds of different chemical components that may be classified according to functional groups. Typical compound classes in the bio-oil were hydrocarbons, organic acids, esters, ketones and heterocyclics. The energy recovery ratio (ERR) reached 93.63%. The bio-oil is expected to contribute to fossil fuel replacement in stationary applications, including boilers and furnaces, and upgrading processes for the bio-oil may be used to obtain liquid transport fuels

Semipermeable membrane devices concentrate mixed function oxygenase inducers from oil sands and refinery wastewaters

International Nuclear Information System (INIS)

Parrott, J.L.; Hewitt, L.M.

2002-01-01

The health of fish in the Athabasca River was examined to determine the effects of both natural and anthropogenic oil sands exposure on liver mixed function oxygenase (MFO) enzymes. Semipermeable membrane devices (SPMD) were used to concentrate bioavailable compounds that may result in MFO induction. The SPMDs were used for a period of 2 weeks in the Steepbank River as well as in oil refinery wastewater and intake ponds. They were then tested to see if they induced ethoxyresorufin-O-deethylase (EROD) activity in hepatoma cells, a cell line derived from a liver cancer of a small fish. SPMDs from the wastewater pond contained potent EROD inducers in fish liver cells. SPMDs from the Athabasca River exhibited some EROD inducers, but they were 1/100 as potent as those of the refinery wastewater. The characteristics of MFO inducers from refinery wastewater were different from natural inducers from the oil sands in the Athabasca and Steepbank Rivers. For instance, log Kow was less than 5 for refinery wastewater, but it was greater than 5 for Athabasca River wastewater and from natural oil sands exposure. In the case of the Steepbank River, the pattern of MFO induction was similar to the MFO induction seen in wild fish.The highest MFO inducers were found to be in the area of the mine, suggesting and anthropogenic pollution source. The less potent inducers were in the area of the natural and undisturbed oil sands. Very few inducers were found outside of the oil sands formation

Solid biofuels production from agricultural residues and processing by-products by means of torrefaction treatment: the case of sunflower chain

Directory of Open Access Journals (Sweden)

Daniele Duca

2014-11-01

Full Text Available The high heterogeneity of some residual biomasses makes rather difficult their energy use. Their standardisation is going to be a key aspect to get good quality biofuels from those residues. Torrefaction is an interesting process to improve the physical and chemical properties of lignocellulosic biomasses and to achieve standardisation. In the present study torrefaction has been employed on residues and by-products deriving from sunflower production chain, in particular sunflower stalks, husks and oil press cake. The thermal behaviour of these materials has been studied at first by thermogravimetric analysis in order to identify torrefaction temperatures range. Afterwards, different residence time and torrefaction temperatures have been tested in a bench top torrefaction reactor. Analyses of raw and torrefied materials have been carried out to assess the influence of the treatment. As a consequence of torrefaction, the carbon and ash contents increase while the volatilisation range reduces making the material more stable and standardised. Mass yield, energy yield and energy densification reach values of about 60%, 80% and 1.33 for sunflower stalks and 64%, 85% and 1.33 for sunflower oil press cake respectively. As highlighted by the results, torrefaction is more interesting for sunflower stalks than oil cake and husks due to their different original characteristics. Untreated oil press cake and husks, in fact, already show a good high heating value and, for this reason, their torrefaction should be mild to avoid an excessive ash concentration. On the contrary, for sunflower stalks the treatment is more useful and could be more severe.

Ex situ bioremediation of oil-contaminated soil.

Science.gov (United States)

Lin, Ta-Chen; Pan, Po-Tsen; Cheng, Sheng-Shung

2010-04-15

An innovative bioprocess method, Systematic Environmental Molecular Bioremediation Technology (SEMBT) that combines bioaugmentation and biostimulation with a molecular monitoring microarray biochip, was developed as an integrated bioremediation technology to treat S- and T-series biopiles by using the landfarming operation and reseeding process to enhance the bioremediation efficiency. After 28 days of the bioremediation process, diesel oil (TPH(C10-C28)) and fuel oil (TPH(C10-C40)) were degraded up to approximately 70% and 63% respectively in the S-series biopiles. When the bioaugmentation and biostimulation were applied in the beginning of bioremediation, the microbial concentration increased from approximately 10(5) to 10(6) CFU/g dry soil along with the TPH biodegradation. Analysis of microbial diversity in the contaminated soils by microarray biochips revealed that Acinetobacter sp. and Pseudomonas aeruginosa were the predominant groups in indigenous consortia, while the augmented consortia were Gordonia alkanivorans and Rhodococcus erythropolis in both series of biopiles during bioremediation. Microbial respiration as influenced by the microbial activity reflected directly the active microbial population and indirectly the biodegradation of TPH. Field experimental results showed that the residual TPH concentration in the complex biopile was reduced to less than 500 mg TPH/kg dry soil. The above results demonstrated that the SEMBT technology is a feasible alternative to bioremediate the oil-contaminated soil. Crown Copyright 2009. Published by Elsevier B.V. All rights reserved.

Carbaryl residues in maize products

International Nuclear Information System (INIS)

Zayed, S.M.A.D.; Mansour, S.A.; Mostafa, I.Y.; Hassan, A.

1976-01-01

The 14 C-labelled insecticide carbaryl was synthesized from [1- 14 C]-1-naphthol at a specific activity of 3.18mCig -1 . Maize plants were treated with the labelled insecticide under simulated conditions of agricultural practice. Mature plants were harvested and studied for distribution of total residues in untreated grains as popularly roasted and consumed, and in the corn oil and corn germ products. Total residues found under these conditions in the respective products were 0.2, 0.1, 0.45 and 0.16ppm. (author)

Comparative assessment of structural-mechanical properties of heavy oils of timano-pechorskaya province

Directory of Open Access Journals (Sweden)

Н. К. Кондрашева

2017-06-01

Full Text Available The physicochemical properties of heavy oils of Yaregskoe and Usinskoe deposits and the residues of atmospheric distillation of petroleum (fuel oil recovered from them are presented. The group composition of oil and the residues of its atmospheric distillation (fuel oil is determined. When using X-ray fluorescence energy dispersive spectrometer, the content of metals in the products is determined. A conclusion is drawn about the distribution of metals in the initial oil and fuel oil. On the basis of rheological characteristics, the type of liquids is determined in accordance with Newton's law, as well as the presence of an anomaly in the viscosity of the studied media at different temperatures. The energy values of the thixotropy of heavy oils of Usinskoe and Yaregskoe deposits, as well as the activation energy of the viscous flow of all media studied, are obtained. The phase transition of atmospheric residues at 60 °C is discovered. Dependences of the enthalpy and entropy of the viscous flow of the studied hydrocarbon media are obtained with an increase in temperature from 10 to 140 °C. The dependences of the oil molecules and atmospheric residues jumping frequency on viscosity are obtained for the first time.

Characterization of Bottom and Fly Ashes Generated Co-incineration of Biomass with Automotive Shredder Residue

Directory of Open Access Journals (Sweden)

Othaman Muhamad Fazli

2017-01-01

Full Text Available One of the viable techniques to reduce land filling of automotive shredder residue is by co-incinerating them with biomass. This study focuses on characterization of bottom and fly ashes produced from the coincineration of the automotive shredded residue with oil palm biomass. The co-incineration was carried out in a pilot-scale fluidized bed incinerator. The oil palm biomass used was oil palm shell while the automotive shredded residue was obtained from a local recycling company. The characterization was done based on particle size distribution, morphology (SEM analysis and chemical composition (EDS analysis. In term of chemical composition the ashes contain C (Carbon, O (Oxygen, Si (Silicon, K (Potassium, Ca (Calcium and Fe (Ferum.

Oils, paintings and chemistry

Directory of Open Access Journals (Sweden)

Maria Eduarda Machado de Araújo

2005-01-01

Full Text Available In oil paintings artists use oils to apply pigments. These oils firstly are liquid and then solidify in a thin film. Many chemical reactions are involved in drying and also in the aging of these oils. Drying is a continuous process that begins with the oxidation of insaturated fatty acids from triglycerides to originate peroxides. These compounds suffer a cascade of reactions that lead to cross linking bonds between fatty acids residues, transforming the oil in a solid film. Identification of the film oil is possible using the palmitic/stearic ratio (P/S by chromatographic (GC and/or spectroscopic techniques. Sterol composition, phytosterols or cholesterol, determined by GC-MS or FTIR techniques, allows investigators to distinguish between oil painting and a temper one that used egg as the binding medium.

Comparison of questionnaire-based estimation of pesticide residue intake from fruits and vegetables with urinary concentrations of pesticide biomarkers.

Science.gov (United States)

Chiu, Yu-Han; Williams, Paige L; Mínguez-Alarcón, Lidia; Gillman, Matthew; Sun, Qi; Ospina, Maria; Calafat, Antonia M; Hauser, Russ; Chavarro, Jorge E

2018-01-01

We developed a pesticide residue burden score (PRBS) based on a food frequency questionnaire and surveillance data on food pesticide residues to characterize dietary exposure over the past year. In the present study, we evaluated the association of the PRBS with urinary concentrations of pesticide biomarkers. Fruit and vegetable (FV) intake was classified as having high (PRBS≥4) or low (PRBSEARTH study. Two urine samples per man were analyzed for seven biomarkers of organophosphate and pyrethroid insecticides, and the herbicide 2,4-dichlorophenoxyacetic acid. We used generalized estimating equations to analyze the association of the PRBS with urinary concentrations of pesticide biomarkers. Urinary concentrations of pesticide biomarkers were positively related to high pesticide FV intake but inversely related to low pesticide FV intake. The molar sum of urinary concentrations of pesticide biomarkers was 21% (95% confidence interval (CI): 2%, 44%) higher for each one serving/day increase in high pesticide FV intake, and 10% (95% CI: 1%, 18%) lower for each one serving/day increase in low pesticide FV intake. Furthermore, intake of high pesticide FVs positively related to most individual urinary biomarkers. Our findings support the usefulness of the PRBS approach to characterize dietary exposure to select pesticides.

Preparation of a novel carbon-based solid acid from cassava stillage residue and its use for the esterification of free fatty acids in waste cooking oil.

Science.gov (United States)

Wang, Lingtao; Dong, Xiuqin; Jiang, Haoxi; Li, Guiming; Zhang, Minhua

2014-04-01

A novel carbon-based solid acid catalyst was prepared by the sulfonation of incompletely carbonized cassava stillage residue (CSR) with concentrated sulfuric acid, and employed to catalyze the esterification of methanol and free fatty acids (FFAs) in waste cooking oil (WCO). The effects of the carbonization and the sulfonation temperatures on the pore structure, acid density and catalytic activity of the CSR-derived catalysts were systematically investigated. Low temperature carbonization and high temperature sulfonation can cause the collapse of the carbon framework, while high temperature carbonization is not conducive to the attachment of SO3H groups on the surface. The catalyst showed high catalytic activity for esterification, and the acid value for WCO is reduced to below 2mg KOH/g after reaction. The activity of catalyst can be well maintained after five cycles. CSR can be considered a promising raw material for the production of a new eco-friendly solid acid catalyst. Copyright © 2014 Elsevier Ltd. All rights reserved.

Isotopic insights into microbial sulfur cycling in oil reservoirs

Directory of Open Access Journals (Sweden)

Christopher G Hubbard

2014-09-01

Full Text Available Microbial sulfate reduction in oil reservoirs (biosouring is often associated with secondary oil production where seawater containing high sulfate concentrations (~28 mM is injected into a reservoir to maintain pressure and displace oil. The sulfide generated from biosouring can cause corrosion of infrastructure, health exposure risks, and higher production costs. Isotope monitoring is a promising approach for understanding microbial sulfur cycling in reservoirs, enabling early detection of biosouring, and understanding the impact of souring. Microbial sulfate reduction is known to result in large shifts in the sulfur and oxygen isotope compositions of the residual sulfate, which can be distinguished from other processes that may be occurring in oil reservoirs, such as precipitation of sulfate and sulfide minerals. Key to the success of this method is using the appropriate isotopic fractionation factors for the conditions and processes being monitored. For a set of batch incubation experiments using a mixed microbial culture with crude oil as the electron donor, we measured a sulfur fractionation factor for sulfate reduction of -30‰. We have incorporated this result into a simplified 1D reservoir reactive transport model to highlight how isotopes can help discriminate between biotic and abiotic processes affecting sulfate and sulfide concentrations. Modeling results suggest that monitoring sulfate isotopes can provide an early indication of souring for reservoirs with reactive iron minerals that can remove the produced sulfide, especially when sulfate reduction occurs in the mixing zone between formation waters containing elevated concentrations of volatile fatty acids and injection water containing elevated sulfate. In addition, we examine the role of reservoir thermal, geochemical, hydrological, operational and microbiological conditions in determining microbial souring dynamics and hence the anticipated isotopic signatures.

Oil-in-Water Emulsions Stabilized by Saponified Epoxidized Soybean Oil-Grafted Hydroxyethyl Cellulose.

Science.gov (United States)

Huang, Xujuan; Li, Qiaoguang; Liu, He; Shang, Shibin; Shen, Minggui; Song, Jie

2017-05-03

An oil-in-water emulsion stabilized by saponified epoxidized soybean oil-grafted hydroxyethyl cellulose (H-ESO-HEC) was investigated. By using an ultrasonic method, oil-in-water emulsions were prepared by blending 50 wt % soybean oil and 50 wt % H-ESO-HEC aqueous suspensions. The influence of H-ESO-HEC concentrations on the properties of oil-in-water emulsions was examined. The H-ESO-HEC concentrations in the aqueous phase varied from 0.02 to 0.40 wt %. When the H-ESO-HEC concentration was 0.4 wt %, the emulsion remained stable for >80 days. The mean droplet sizes of the emulsions decreased by increasing the H-ESO-HEC concentration and extending the ultrasonic time. The adsorption amounts of H-ESO-HEC at the oil-water interface increased when the H-ESO-HEC concentrations in the aqueous phase increased. The rheological property revealed that the apparent viscosity of the H-ESO-HEC-stabilized oil-in-water emulsions increased when the H-ESO-HEC concentrations increased. Steady flow curves indicated an interfacial film formation in the emulsions. The evolution of G', G″, and tan η indicated the predominantly elastic behaviors of all the emulsions.

Characterization of residual oils for biodiesel production

Directory of Open Access Journals (Sweden)

Edmilson Antonio Canesin

2014-01-01

Conclusions: The obtained results suggesting that it is possible to take advantage of these residues for biodiesel production as the obtained products were approved according to the rules established by the National Association of Petroleum (ANP; the bovine samples were the exception regarding moisture and acidity.

Efficacy of essential oil of Piper aduncum against nymphs and adults of Diaphorina citri.

Science.gov (United States)

Volpe, Haroldo Xl; Fazolin, Murilo; Garcia, Rafael B; Magnani, Rodrigo F; Barbosa, José Carlos; Miranda, Marcelo P

2016-06-01

Insecticide application is the main way to control Diaphorina citri. However, it causes environmental contamination, has a negative impact on beneficial organisms and leads to psyllid resistance. The essential oil of Piper aduncum has low toxicity towards the environment and contains dillapiol, which has proven to be effective against several crop pests. Here, we studied its efficacy against nymphs and adults of D. citri under laboratory conditions. Oils with three concentrations of dillapiol (69.3, 79.9 and 85.4%) at 0.5, 0.75 and 1.0% dilutions plus 0.025% adjuvant were tested. All treatments caused 90-100% mortality in nymphs. Topical treatments with oil containing 79.9 and 85.4% dillapiol at 0.75% and 1% dilutions were effective (mortality ≥80%) in adults. However, the essential oil showed no residual activity against adults (mortality ≤30%). Dillapiol-rich oil is a promising compound for D. citri control. © 2015 Society of Chemical Industry. © 2015 Society of Chemical Industry.

Effectiveness of control strategies against Botrytis cinerea in vineyard and evaluation of the residual fungicide concentrations.

Science.gov (United States)

Gabriolotto, Chiara; Monchiero, Matteo; Negre, Michele; Spadaro, Davide; Gullino, Maria Lodovica

2009-05-01

This investigation was undertaken to test different control strategies against Botrytis cinerea vineyards. Two commercial vineyards, "Barbera" and "Moscato," located in Piedmont (Northern Italy) were divided into seven plots and treated with different combinations of fungicides including fenhexamid, pyrimethanil, fludioxonil + cyprodinil, iprodione, and boscalid, a new carboxamide compound. An integrated strategy including a chemical (pyrimethanil) and a biocontrol agent (Trichoderma spp. t2/4ph1) was also included. At harvest, the percentage of bunches and berries attacked by B. cinerea and the concentration of the chemical fungicides were determined. All the pesticide residues at harvest were below the maximum residue level (MRL), except when two applications of pyrimethanil per season were applied. Boscalid was the most effective active ingredient against B. cinerea among the tested chemicals. When boscalid application was followed by a treatment with pyrimethanil, its efficacy was similar to that shown by two treatments of pyrimethanil. However, this second strategy was not feasible due to the risks of resistance development in the pathogen and to the residue accumulation as indicated by the analysis.

Radioactive contamination of oil produced from nuclear-broken shale

International Nuclear Information System (INIS)

Arnold, W.D.; Crouse, D.J.

1970-01-01

The results of small-scale exposure and retorting tests indicate that oil recovered from shale that has been broken with nuclear explosives will be contaminated with tritium. When oil shale was heated in sealed flasks with tritiated water vapor or with tritiated hydrogen, both the shale and the oil subsequently retorted from the shale contained tritium. There was much less contamination of the shale or oil, however, when the shale was exposed to tritiated methane and ethane. Contamination of shale and oil with tritium, as the result, of exposure to tritiated water, increased as the exposure temperature, exposure pressure, and the tritium concentration in the water were increased. This contamination also increased as the exposure time was increased up to 25 days, but not significantly thereafter. More than 90% of the tritium was removed from contaminated shale by treating the shale with moist air at elevated temperatures. Only small amounts of the tritium were removed from crude oil by contacting it with solid drying agents or with water. When tritium-contaminated shale oil was distilled, the tritium contents of the recovered fractions were found to be approximately equal. After being heated with a sample of underground test-shot debris, liquid shale oil became contaminated with radioactive fission products. Most of the radioactivity of the oil was due to finely dispersed solids rather than to dissolved radionuclides. Filtration of the oil removed a major fraction of the radioactive material. When the contaminated oil was distilled, more than 99% of the radionuclides remained in the pot residue. (author)

Radioactive contamination of oil produced from nuclear-broken shale

Energy Technology Data Exchange (ETDEWEB)

Arnold, W D; Crouse, D J

1970-05-15

The results of small-scale exposure and retorting tests indicate that oil recovered from shale that has been broken with nuclear explosives will be contaminated with tritium. When oil shale was heated in sealed flasks with tritiated water vapor or with tritiated hydrogen, both the shale and the oil subsequently retorted from the shale contained tritium. There was much less contamination of the shale or oil, however, when the shale was exposed to tritiated methane and ethane. Contamination of shale and oil with tritium, as the result, of exposure to tritiated water, increased as the exposure temperature, exposure pressure, and the tritium concentration in the water were increased. This contamination also increased as the exposure time was increased up to 25 days, but not significantly thereafter. More than 90% of the tritium was removed from contaminated shale by treating the shale with moist air at elevated temperatures. Only small amounts of the tritium were removed from crude oil by contacting it with solid drying agents or with water. When tritium-contaminated shale oil was distilled, the tritium contents of the recovered fractions were found to be approximately equal. After being heated with a sample of underground test-shot debris, liquid shale oil became contaminated with radioactive fission products. Most of the radioactivity of the oil was due to finely dispersed solids rather than to dissolved radionuclides. Filtration of the oil removed a major fraction of the radioactive material. When the contaminated oil was distilled, more than 99% of the radionuclides remained in the pot residue. (author)

Surfactant-aided recovery/in situ bioremediation for oil-contaminated sites

International Nuclear Information System (INIS)

Ducreaux, J.; Baviere, M.; Seabra, P.; Razakarisoa, O.; Shaefer, G.; Arnaud, C.

1995-01-01

Bioremediation has been the most commonly used method way for in situ cleaning of soils contaminated with low-volatility petroleum products such as diesel oil. However, whatever the process (bioventing, bioleaching, etc.), it is a time-consuming technique that may be efficiency limited by both accessibility and too high concentrations of contaminants. A currently developed process aims at quickly recovering part of the residual oil in the vadose and capillary zones by surfactant flushing, then activating in situ biodegradation of the remaining oil in the presence of the same or other surfactants. The process has been tested in laboratory columns and in an experimental pool, located at the Institut Franco-Allemand de Recherche sur l'Environnement (IFARE) in Strasbourg, France. Laboratory column studies were carried out to fit physico-chemical and hydraulic parameters of the process to the field conditions. The possibility of recovering more than 80% of the oil in the flushing step was shown. For the biodegradation step, forced aeration as a mode of oxygen supply, coupled with nutrient injection aided by surfactants, was tested

Catalytic hydroprocessing of heavy oil feedstocks

International Nuclear Information System (INIS)

Okunev, A G; Parkhomchuk, E V; Lysikov, A I; Parunin, P D; Semeikina, V S; Parmon, V N

2015-01-01

A grave problem of modern oil refining industry is continuous deterioration of the produced oil quality, on the one hand, and increase in the demand for motor fuels, on the other hand. This necessitates processing of heavy oil feedstock with high contents of sulfur, nitrogen and metals and the atmospheric residue. This feedstock is converted to light oil products via hydrogenation processes catalyzed by transition metal compounds, first of all, cobalt- or nickel-promoted molybdenum and tungsten compounds. The processing involves desulfurization, denitrogenation and demetallization reactions as well as reactions converting heavy hydrocarbons to lighter fuel components. The review discusses the mechanisms of reactions involved in the heavy feedstock hydroprocessing, the presumed structure and state of the catalytically active components and methods for the formation of supports with the desired texture. Practically used and prospective approaches to catalytic upgrading of heavy oil feedstock as well as examples of industrial processing of bitumen and vacuum residues in the presence of catalysts are briefly discussed. The bibliography includes 140 references

Catalytic hydroprocessing of heavy oil feedstocks

Science.gov (United States)

Okunev, A. G.; Parkhomchuk, E. V.; Lysikov, A. I.; Parunin, P. D.; Semeikina, V. S.; Parmon, V. N.

2015-09-01

A grave problem of modern oil refining industry is continuous deterioration of the produced oil quality, on the one hand, and increase in the demand for motor fuels, on the other hand. This necessitates processing of heavy oil feedstock with high contents of sulfur, nitrogen and metals and the atmospheric residue. This feedstock is converted to light oil products via hydrogenation processes catalyzed by transition metal compounds, first of all, cobalt- or nickel-promoted molybdenum and tungsten compounds. The processing involves desulfurization, denitrogenation and demetallization reactions as well as reactions converting heavy hydrocarbons to lighter fuel components. The review discusses the mechanisms of reactions involved in the heavy feedstock hydroprocessing, the presumed structure and state of the catalytically active components and methods for the formation of supports with the desired texture. Practically used and prospective approaches to catalytic upgrading of heavy oil feedstock as well as examples of industrial processing of bitumen and vacuum residues in the presence of catalysts are briefly discussed. The bibliography includes 140 references.

Oils from different depth in the Alagoas sub-basin distribution and concentration; Oleos em diferentes profundidades na sub-bacia Alagoas: distribuicao e econcentracao

Energy Technology Data Exchange (ETDEWEB)

Reboucas, Lucia M.C.; Sant' Ana, Antonio E.G.; Sabino, Adilson R.; Nogueira, Fred A.R.; Moraes, Reinaldo J.R.; Crispim, Alessandre [Universidade Federal de Alagoas (UFAL), Maceio, AL (Brazil). Inst. de Quimica e Biotecnologia . Lab. de Analises de Biomarcadores e Semioquimicos]. E-mail: lmcr@qui.ufal.br

2008-07-01

This paper reports the distribution and the concentration of n-alkane homologue series and the HPA compounds in 22 oils from Alagoas sub-basin, Pilar Field, Brazil. The n-alkane profile of whole oil gas chromatograms (CG-FID) to light, medium and heave oils represented no-biodegraded oils. The light and medium oils have n-alkane distribution with a maximum in nC{sub 10} and nC{sub 17}. The ration pristine/phytane (P/F) between 1,5 and 2,7 suggest Lacustrine origin. The nalkane distribution from the heavy oils show two maximum between nC{sub 15} and nC{sub 23}. The concentrations of n-alkane are different to all the 22 oils. The F2 fraction classified as light (API>39), medium (36oils show that they can be readily distinguished to three or four oil families in each oil class. Therefore, it seems that the same oil can belong to different family accord to abundance of n-alkane or to the HPA, F2 fraction, compounds. By the F2 fraction we can suggest different families or different migration route. The oils show by GC-MS (characteristic ion m/z to each class) abundant fluorenone and alkylfluorenones compounds. Other HPA homologue series compounds as: naphthalene, biphenyl, phenanthrene, dibenzothiophene, dibenzofuran, chrysene, mono- and triaromatic steroid, benzohopane and their alkyl derivates, were identified in the oils. (author)

Oil spills

International Nuclear Information System (INIS)

Katsouros, M.H.

1992-01-01

The world annually transports 1.7 billion tons of oil by sea, and oil spills, often highly concentrated discharges, are increasing from a variety of sources. The author discusses sources of oils spills: natural; marine transportation; offshore oil production; atmospheric sources; municipal industrial wastes and runoff. Other topics include: the fate of the spilled oil; the effects of the oil; the response to oil spills; and prevention of oil spills. 30 refs., 1 fig., 4 tabs

Efficiency of methods for Karl Fischer determination of water in oils based on oven evaporation and azeotropic distillation.

Science.gov (United States)

Larsson, William; Jalbert, Jocelyn; Gilbert, Roland; Cedergren, Anders

2003-03-15

The efficiency of azeotropic distillation and oven evaporation techniques for trace determination of water in oils has recently been questioned by the National Institute of Standards and Technology (NIST), on the basis of measurements of the residual water found after the extraction step. The results were obtained by volumetric Karl Fischer (KF) titration in a medium containing a large excess of chloroform (> or = 65%), a proposed prerequisite to ensure complete release of water from the oil matrix. In this work, the extent of this residual water was studied by means of a direct zero-current potentiometric technique using a KF medium containing more than 80% chloroform, which is well above the concentration recommended by NIST. A procedure is described that makes it possible to correct the results for dilution errors as well as for chemical interference effects caused by the oil matrix. The corrected values were found to be in the range of 0.6-1.5 ppm, which should be compared with the 12-34 ppm (uncorrected values) reported by NIST for the same oils. From this, it is concluded that the volumetric KF method used by NIST gives results that are much too high.

A diet rich in monounsaturated rapeseed oil reduces the lipoprotein cholesterol concentration and increases the relative content of n-3 fatty acids in serum in hyperlipidemic subjects.

Science.gov (United States)

Gustafsson, I B; Vessby, B; Ohrvall, M; Nydahl, M

1994-03-01

The effects of 3 wk on a diet rich in monounsaturated rapeseed oil were compared with those of a diet containing sunflower oil within a lipid-lowering diet. Ninety-five subjects with moderate hyperlipoproteinemia were randomly assigned to one of the two well-controlled diets prepared at the hospital kitchen. Total serum, low-density- and high-density-lipoprotein cholesterol concentrations decreased by 15%, 16%, and 11% (P oil diet and by 16%, 14%, and 13% (P oil diet. Serum triglycerides decreased more markedly (by 29%, P oil than on the rapeseed oil diet (14%, P oil diet but decreased on the sunflower oil diet. There was an increase in the alpha-tocopherol concentrations after both diets. The findings indicate that low erucic acid rapeseed oil can replace oils and fats rich in polyunsaturated fatty acids in a lipid-lowering diet.

Investigation of biosurfactant-producing indigenous microorganisms that enhance residue oil recovery in an oil reservoir after polymer flooding.

Science.gov (United States)

She, Yue-Hui; Zhang, Fan; Xia, Jing-Jing; Kong, Shu-Qiong; Wang, Zheng-Liang; Shu, Fu-Chang; Hu, Ji-Ming

2011-01-01

Three biosurfactant-producing indigenous microorganisms (XDS1, XDS2, XDS3) were isolated from a petroleum reservoir in the Daqing Oilfield (China) after polymer flooding. Their metabolic, biochemical, and oil-degradation characteristics, as well as their oil displacement in the core were studied. These indigenous microorganisms were identified as short rod bacillus bacteria with white color, round shape, a protruding structure, and a rough surface. Strains have peritrichous flagella, are able to produce endospores, are sporangia, and are clearly swollen and terminal. Bacterial cultures show that the oil-spreading values of the fermentation fluid containing all three strains are more than 4.5 cm (diameter) with an approximate 25 mN/m surface tension. The hydrocarbon degradation rates of each of the three strains exceeded 50%, with the highest achieving 84%. Several oil recovery agents were produced following degradation. At the same time, the heavy components of crude oil were degraded into light components, and their flow characteristics were also improved. The surface tension and viscosity of the crude oil decreased after being treated by the three strains of microorganisms. The core-flooding tests showed that the incremental oil recoveries were 4.89-6.96%. Thus, XDS123 treatment may represent a viable method for microbial-enhanced oil recovery.

Potential of castor bean (Ricinus communis L.) for phytoremediation of mine tailings and oil production.

Science.gov (United States)

Ruiz Olivares, Alejandro; Carrillo-González, Rogelio; González-Chávez, Ma del Carmen A; Soto Hernández, Ramón Marcos

2013-01-15

Bioenergy production combined with phytoremediation has been suggested to help in solving two critical world problems: the gradual reduction of fossil fuels and soil contamination. The aim of this research was to investigate the potential for the use of Ricinus communis L. (castor oil plant) as an energy crop and plant species to remediate metal-polluted sites. This study was performed in mine tailings containing high concentrations of Cu, Zn, Mn, Pb and Cd. Physico-chemical characterization, total, DTPA-extractable and water-soluble metals in rhizospheric tailings heap samples were carried. Metal concentrations in plant tissues and translocation factors (TFs) were also determined. The Ricinus seed-oil content was high between 41 and 64%, seeds from San Francisco site 6 had the highest oil content, while these from site 7 had the lowest. No trend between oil yield vs seed origin site was observed. Seed-oil content was negatively correlated with root concentration of Cu, Zn, Pb and Cd, but no correlation was observed with the extractable-metals. According to its shoot metal concentrations and TFs, castor bean is not a metal accumulator plant. This primary colonizing plant is well suited to cope with the local toxic conditions and can be useful for the stabilization of these residues, and for then decreasing metal bioavailability, dispersion and human health risks on these barren tailings heaps and in the surrounding area. Our work is the first report regarding combined oil production and a phytostabilization role for Ricinus plants in metal mine tailings and may give a new value to suitable metal-polluted areas. Copyright © 2012 Elsevier Ltd. All rights reserved.