Evaluation of P-Listed Pharmaceutical Residues in Empty ...

Science.gov (United States)

Under the Resource Conservation and Recovery Act (RCRA), some pharmaceuticals are considered acute hazardous wastes because their sole active pharmaceutical ingredients are P-listed commercial chemical products (40 CFR 261.33). Hospitals and other healthcare facilities have struggled with RCRA's empty container requirements when it comes to disposing of visually empty warfarin and nicotine containers, and this issue is in need of investigation. For example, nicotine gums, patches and lozenges are hazardous wastes because nicotine and its salts are listed as P075, and Coumadin (also known as warfarin) is hazardous because warfarin and its salts are listed as P001 (when warfarin is present at concentrations greater than 0.3%). Therefore, when unused nicotine-based smoking cessation products (e.g., patches, gum and lozenges) and Coumadin are discarded, they are acute hazardous wastes and must be managed in accordance with all applicable RCRA regulations. Furthermore, due to additional management requirements for P-listed wastes, any acute hazardous water residues remaining in containers (and therefore the container itself) must be managed as hazardous unless the container has been rendered

Earthquake Hazard in the New Madrid Seismic Zone Remains a Concern

Science.gov (United States)

Frankel, A.D.; Applegate, D.; Tuttle, M.P.; Williams, R.A.

2009-01-01

There is broad agreement in the scientific community that a continuing concern exists for a major destructive earthquake in the New Madrid seismic zone. Many structures in Memphis, Tenn., St. Louis, Mo., and other communities in the central Mississippi River Valley region are vulnerable and at risk from severe ground shaking. This assessment is based on decades of research on New Madrid earthquakes and related phenomena by dozens of Federal, university, State, and consulting earth scientists. Considerable interest has developed recently from media reports that the New Madrid seismic zone may be shutting down. These reports stem from published research using global positioning system (GPS) instruments with results of geodetic measurements of strain in the Earth's crust. Because of a lack of measurable strain at the surface in some areas of the seismic zone over the past 14 years, arguments have been advanced that there is no buildup of stress at depth within the New Madrid seismic zone and that the zone may no longer pose a significant hazard. As part of the consensus-building process used to develop the national seismic hazard maps, the U.S. Geological Survey (USGS) convened a workshop of experts in 2006 to evaluate the latest findings in earthquake hazards in the Eastern United States. These experts considered the GPS data from New Madrid available at that time that also showed little to no ground movement at the surface. The experts did not find the GPS data to be a convincing reason to lower the assessment of earthquake hazard in the New Madrid region, especially in light of the many other types of data that are used to construct the hazard assessment, several of which are described here.

Evaluation of PAH depletion of subsurface Exxon Valdez oil residues remaining in Prince William Sound in 2007-2008 and their likely bioremediation potential

Energy Technology Data Exchange (ETDEWEB)

Atlas, R. [Louisville Univ., Louisville, KY (United States); Bragg, J.R. [Creative Petroleum Solutions LLC, Houston, TX (United States)

2009-07-01

This study examined the extent of oil weathering at the Exxon Valdez oil spill (EVOS) sites and estimated the bioremediation potential for shoreline segments by examining the depletion of total polycyclic aromatic hydrocarbons (PAHs) relative to an estimated applicability threshold of 70 per cent. The distribution of oil was examined by location and current ratios of nitrogen and non-polar oil in order to assess if biodegradation rates were nutrient-limited. The impact of sequestration on the effectiveness of bioremediation was also studied. Results of the study showed that the EVOS residues are patchy and infrequently found on sites that were heavily oiled in 1989. Only 0.4 per cent of the oil originally stranded in 1989 remained. The remaining EVOS residues are sequestered under boulder and cobble armour in areas with limited contact with flowing water. The study also showed that concentrations of nitrogen and dissolved oxygen in pore waters within strata adjacent to the sequestered oil can support biodegradation. Most remaining EVOS residues are highly weathered and biodegraded. It was concluded that nutrients added to the shorelines are unlikely to effectively contact the sequestered oil. 31 refs., 2 tabs., 14 figs.

40 CFR 180.34 - Tests on the amount of residue remaining.

Science.gov (United States)

2010-07-01

...) PESTICIDE PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Procedural Regulations..., cauliflower, kohlrabi. (12) Cantaloups, honeydew melons, muskmelons, pumpkins, watermelons, winter squash. (13...

Managing hazards in place: The risks of residual risks.

Science.gov (United States)

Silbergeld, Ellen K

2017-10-01

Managing hazards in place (MHP) is a policy instrument in environmental health that allows less than complete removal, abatement, or remediation of environmental hazards. The practice of minimizing exposure to hazards rather than removing them is widely recognized as part of the toolbox of environmental protection for human and ecosystem health. The concept of managing hazards in place is embedded in several environmental statutes and regulations in the US notably the waste management regulations, as well as in the Safe Drinking Water Act and the Clean Water Act. While this commentary focuses largely on applications of MHP in the US, this policy is also utilized by agencies in many other countries for managing hazardous waste sites, lead in housing and drinking water systems, and environmental contamination of rivers and estuaries. The rationale for this concept is not difficult to understand: MHP policies can reduce the costs of meeting environmental goals; it can provide opportunities for access to resources that have been contaminated by past actions such as waste disposal, and it can enhance land and property values as well as tax revenues all of which are important to home owners and communities. The concerns related to this concept are also not difficult to understand: an incompletely abated or contained hazard may present future exposure risks to humans and environmental biota. Further, the compromise implicit in MHP is the assurance of indefinite oversight and monitoring to detect any releases. To that extent, MHP involves both sociology as well as toxicology and the exposure sciences. Because of the prevalence of managing hazards in place, this commentary suggests that evaluation of its performance is needed. Copyright © 2017 Elsevier Inc. All rights reserved.

Proposal for management and alkalinity transformation of bauxite residue in China.

Science.gov (United States)

Xue, Shengguo; Kong, Xiangfeng; Zhu, Feng; Hartley, William; Li, Xiaofei; Li, Yiwei

2016-07-01

Bauxite residue is a hazardous solid waste produced during the production of alumina. Its high alkalinity is a potential threat to the environment which may disrupt the surrounding ecological balance of its disposal areas. China is one of the major global producers of alumina and bauxite residue, but differences in alkalinity and associated chemistry exist between residues from China and those from other countries. A detailed understanding of the chemistry of bauxite residue remains the key to improving its management, both in terms of minimizing environmental impacts and reducing its alkaline properties. The nature of bauxite residue and the chemistry required for its transformation are still poorly understood. This review focuses on various transformation processes generated from the Bayer process, sintering process, and combined Bayer-sintering process in China. Problems associated with transformation mechanisms, technical methods, and relative merits of these technologies are reviewed, while current knowledge gaps and research priorities are recommended. Future research should focus on transformation chemistry and its associated mechanisms and for the development of a clear and economic process to reduce alkalinity and soda in bauxite residue.

77 FR 24671 - Compliance Guide for Residue Prevention and Agency Testing Policy for Residues

Science.gov (United States)

2012-04-25

... Hazard Analysis and Critical Control Points (HACCP) inspection system, another important component of the NRP is to provide verification of residue control in HACCP systems. As part of the HACCP regulation... guide, and FSIS finds violative residues, the establishment's HACCP system may be inadequate under 9 CFR...

77 FR 12497 - Hazardous Waste Management System; Identification and Listing of Hazardous Waste Exclusion

Science.gov (United States)

2012-03-01

...,'' from the list of hazardous wastes, a maximum of 200 cubic yards per year of residual solids from sludge... accept the delisted processed storm water tank sludge. This rule also imposes testing conditions for... of F037 residual solids from processing (for oil recovery) sludge removed from two storm water tanks...

75 FR 61356 - Hazardous Waste Management System; Identification and Listing of Hazardous Waste; Correction

Science.gov (United States)

2010-10-05

... Waste Management System; Identification and Listing of Hazardous Waste; Correction AGENCY: Environmental... thermal desorber residual solids with Hazardous Waste Numbers: F037, F038, K048, K049, K050, and K051. In... and correcting it in Table 1 of appendix IX to part 261--Waste Excluded Under Sec. Sec. 260.20 and 260...

Potential hazards in smoke-flavored fish

Science.gov (United States)

Lin, Hong; Jiang, Jie; Li, Donghua

2008-08-01

Smoking is widely used in fish processing for the color and flavor. Smoke flavorings have evolved as a successful alternative to traditional smoking. The hazards of the fish products treated by liquid-smoking process are discussed in this review. The smoke flavoring is one important ingredient in the smoke-flavored fish. This paper gives the definition of smoke flavorings and the hazard of polycyclic aromatic hydrocarbons (PAHs) residue in the smoke flavorings on the market. It gives also an assessment of chemical hazards such as carcinogenic PAHs, especially Benzo-[ a]pyrene, as well as biological hazards such as Listeria monocytogenes, Clostridium botulinum, histamine and parasites in smoke-flavored fish. The limitations in regulations or standards are discussed. Smoke flavored fish have lower content of PAHs as compared with the traditional smoking techniques if the PAHs residue in smoke flavorings is controlled by regulations or standards.

Facilitating the enzymatic saccharification of pulped bamboo residues by degrading the remained xylan and lignin-carbohydrates complexes.

Science.gov (United States)

Huang, Caoxing; He, Juan; Li, Xin; Min, Douyong; Yong, Qiang

2015-09-01

Kraft pulping was performed on bamboo residues and its impact on the chemical compositions and the enzymatic digestibility of the samples were investigated. To improve the digestibility of sample by degrading the xylan and lignin-carbohydrates complexes (LCCs), xylanase and α-L-arabinofuranosidase (AF) were supplemented with cellulase. The results showed more carbohydrates were remained in the samples pulped with low effective alkali (EA) charge, compared to conventional kraft pulping. When 120 IU/g xylanase and 15 IU/g AF were supplemented with 20 FPU/g cellulase, the xylan degradation yield of the sample pulped with 12% EA charge increased from 68.20% to 88.35%, resulting in an increased enzymatic saccharification efficiency from 58.98% to 83.23%. The amount of LCCs in this sample decreased from 8.63/100C9 to 2.99/100C9 after saccharification with these enzymes. The results indicated that degrading the remained xylan and LCCs in the pulp could improve its enzymatic digestibility. Copyright © 2015 Elsevier Ltd. All rights reserved.

Studies of the magnitude and nature of pesticide residues in stored products, using radiotracer techniques

International Nuclear Information System (INIS)

1990-01-01

Growing world population and food demand have dictated the introduction of intensive agricultural practices, including the use of an increasing range of agrochemicals. The utilization of these chemicals has a positive and often dramatic impact on agricultural production, but every effort has to be made to ensure safety in use. This is a dynamic challenge for many countries and necessitates the implementation of adequate monitoring programmes. Even when pesticide use conforms to currently adopted standards of good management practice, undesirable side effects may occur and could, at times, endanger public health. Nuclear techniques provide a valuable tool for studying pesticide residues in stored food commodities. Radioisotopes can be used to determine total quantities of residue present, the nature of the residue (i.e. both undecomposed parent material and reaction products), rates of breakdown and loss and distribution in the food material. All of this information is essential for health and regulatory authorities to establish and maintain comprehensive tolerance standards that will protect the health of the consumer. The use of 14 C labelled compounds constitutes a superior and unrivalled tool, in particular for the detection and quantification of grain bound residues. All pesticide residues remaining on or in food materials are of potential concern to human health. Surface residues that remain on commodities such as grain may present an occupational risk to workers exposed to dust emanating from the commodity; residues that remain in food may be a hazard to the consumer. The nature of the residue, the quantity present and its toxicological significance should be known so that tolerance levels can be established and complied with. Refs, figs and tabs

Classification and identification of hazardous residues; Clasificacion e identificacion de residuos peligrosos

Energy Technology Data Exchange (ETDEWEB)

Soto V, Federico; Obaya V, Adolfo; Guerrero, Claudia [Universidad Nacional Autonoma de Mexico, Mexico, D.F. (Mexico)

1996-06-01

In this work, we present the classification and identification of hazardous industrial residues. Mexico has had a wide industrial development in last years, for instance the chemical, steel and petroleum industries, and it has had important effects in the waste industrial generation from different processes. For this reason it is important to diffuse how the correct classification and identification of industrial wastes is made, for insuring their handling, treatment and adequate disposal. [Spanish] En este articulo se presentan los principales aspectos a considerar en la clasificacion e identificacion de los residuos industriales peligrosos. Mexico, considerado como un pais en vias de desarrollo, ha mantenido en los ultimos anos un amplio crecimiento industrial y uno de los mas altos del mundo en poblacion. Esta situacion ha orillado a intensificar la explotacion de los recursos naturales mediante la actividad minera, la siderurgica, la industria quimica, la petrolera, etcetera. Todo esto ha repercutido indudablemente en la generacion de residuos de tan diversa naturaleza como lo son los procesos y las materias primas involucradas, con caracteristicas que van desde los poco riesgosos hasta los altamente peligrosos. Por esta razon, la clasificacion e identificacion de los residuos peligrosos es de suma importancia para asegurar su adecuado manejo, tratamiento y disposicion.

Thermal treatment system of hazardous residuals in three heating zones based on a microprocessor; Sistema de tratamiento termico de residuos peligrosos en tres zonas de calentamiento a base de un microcontrolador.

Energy Technology Data Exchange (ETDEWEB)

Luna H, C L

1997-12-01

Thermal treatment system consists of a high power electric oven of three heating zones where each zone works up to 1200 Centigrades; it has the capacity of rising the central zone temperature up to 1000 Centigrades in 58 minutes approximately. This configuration of three zones could be programmed to different temperatures and they will be digitally controlled by a control microprocessor, which has been controlled by its own assembler language, in function of the PID control. There are also other important controls based on this microprocessor, as a signal amplification, starting and shutdown of high power step relays, activation and deactivation of both analogic/digital and digital/analogic convertors, port activation and basic data storage of the system. Two main characteristics were looked for this oven design; the first was the possibility of controlling the three zone temperature and the second was to reduce the rising and stabilization operation time and its digitized control. The principal function of the three zone oven is to accelerate the degradation of hazardous residuals by an oxidation instead combustion, through relatively high temperatures (minimum 800 Centigrades and maximum 1200 Centigrades); this process reduces the ash and volatile particulate production. The hazardous residuals will be pumped into the degradation system and after atomized through a packaged column; this step will avoid the direct contact of the residuals with the oven cores. These features make this system as closed process, which means that the residuals can not leak to the working area, reducing the exposure risk to the personnel. This three step oven system is the first stage of the complete hazardous residuals degradation system; after this, the flow will go into a cold plasma region where the process is completed, making a closed system. (Author).

Electrodialytic remediation of air pollution control residues

DEFF Research Database (Denmark)

Jensen, Pernille Erland

Air pollution control (APC) residue from municipal solid waste incineration (MSWI) consists of the fly ash, and, in dry and semi-dry systems, also the reaction products from the flue gas cleaning process. APC residue is considered a hazardous waste due to its high alkalinity, high content of salt...

Occupational health hazards in mining: an overview

Energy Technology Data Exchange (ETDEWEB)

Donoghue, A.M. [Alcoa World Alumina Australia, Perth, WA (Australia)

2004-08-01

This review article outlines the physical, chemical, biological, ergonomic and psychosocial occupational health hazards of mining and associated metallurgical processes. Mining remains an important industrial sector in many parts of the world and although substantial progress has been made in the control of occupational health hazards, there remains room for further risk reduction. This applies particularly to traumatic injury hazards, ergonomic hazards and noise. Vigilance is also required to ensure exposures to coal dust and crystalline silica remain effectively controlled.

Quadratic residues and non-residues selected topics

CERN Document Server

Wright, Steve

2016-01-01

This book offers an account of the classical theory of quadratic residues and non-residues with the goal of using that theory as a lens through which to view the development of some of the fundamental methods employed in modern elementary, algebraic, and analytic number theory. The first three chapters present some basic facts and the history of quadratic residues and non-residues and discuss various proofs of the Law of Quadratic Reciprosity in depth, with an emphasis on the six proofs that Gauss published. The remaining seven chapters explore some interesting applications of the Law of Quadratic Reciprocity, prove some results concerning the distribution and arithmetic structure of quadratic residues and non-residues, provide a detailed proof of Dirichlet’s Class-Number Formula, and discuss the question of whether quadratic residues are randomly distributed. The text is a valuable resource for graduate and advanced undergraduate students as well as for mathematicians interested in number theory.

Criteria and Processes for the Certification of Non-Radioactive Hazardous and Non-Hazardous Wastes

International Nuclear Information System (INIS)

Dominick, J.

2008-01-01

This document details Lawrence Livermore National Laboratory's (LLNL) criteria and processes for determining if potentially volumetrically contaminated or potentially surface contaminated wastes are to be managed as material containing residual radioactivity or as non-radioactive. This document updates and replaces UCRL-AR-109662, Criteria and Procedures for the Certification of Nonradioactive Hazardous Waste (Reference 1), also known as 'The Moratorium', and follows the guidance found in the U.S. Department of Energy (DOE) document, Performance Objective for Certification of Non-Radioactive Hazardous Waste (Reference 2). The 1992 Moratorium document (UCRL-AR-109662) is three volumes and 703 pages. The first volume provides an overview of the certification process and lists the key radioanalytical methods and their associated Limits of Sensitivities. Volumes Two and Three contain supporting documents and include over 30 operating procedures, QA plans, training documents and organizational charts that describe the hazardous and radioactive waste management system in place in 1992. This current document is intended to update the previous Moratorium documents and to serve as the top-tier LLNL institutional Moratorium document. The 1992 Moratorium document was restricted to certification of Resource Conservation and Recovery Act (RCRA), State and Toxic Substances Control Act (TSCA) hazardous waste from Radioactive Material Management Areas (RMMA). This still remains the primary focus of the Moratorium; however, this document increases the scope to allow use of this methodology to certify other LLNL wastes and materials destined for off-site disposal, transfer, and re-use including non-hazardous wastes and wastes generated outside of RMMAs with the potential for DOE added radioactivity. The LLNL organization that authorizes off-site transfer/disposal of a material or waste stream is responsible for implementing the requirements of this document. The LLNL Radioactive and

Electrodialytically treated MSWI APC residue as substitute for cement in mortar

DEFF Research Database (Denmark)

Kirkelund, Gunvor Marie; Geiker, Mette Rica; Jensen, Pernille Erland

2014-01-01

Air pollution control (APC) residues from municipal solid waste incineration (MSWI) are considered hazardous waste and need pretreatment prior to possible reuse. Here, two MSWI APC residues, from which the most mobile fraction of heavy metals and salts has been removed by carbonation and/or elect......Air pollution control (APC) residues from municipal solid waste incineration (MSWI) are considered hazardous waste and need pretreatment prior to possible reuse. Here, two MSWI APC residues, from which the most mobile fraction of heavy metals and salts has been removed by carbonation and....../or electrodialytic remediation, were used in Portland cement mortar. Mortar bars with 15 % weight replacement of cement by APC residues showed compressive strengths up to 40 MPa after 28/32 days. Heavy metal and salt leaching from both crushed and monolithic mortars with APC residues was generally similar...

Residues in food derived from animals

International Nuclear Information System (INIS)

Grossklaus, D.

1989-01-01

The first chapter presents a survey of fundamentals and methods of the detection and analysis of residues in food derived from animals, also referring to the resulting health hazards to man, and to the relevant legal provisions. The subsequent chapters have been written by experts of the Federal Health Office, each dealing with particular types of residues such as those of veterinary drugs, additives to animal feeds, pesticide residues, and with environmental pollutants and the contamination of animal products with radionuclides. (MG) With 35 figs., 61 tabs [de

Electroremediation of air pollution control residues in a continuous reactor

DEFF Research Database (Denmark)

Jensen, Pernille Erland; Ferreira, Célia M. D.; Hansen, Henrik K.

2010-01-01

Air pollution control (APC) residue from municipal solid waste incineration is considered hazardous waste due to its alkalinity and high content of salts and mobile heavy metals. Various solutions for the handling of APC-residue exist, however most commercial solutions involve landfilling. A demand...... were made with raw residue, water-washed residue, acid washed residue and acid-treated residue with emphasis on reduction of heavy metal mobility. Main results indicate that the reactor successfully removes toxic elements lead, copper, cadmium and zinc from the feed stream, suggesting...

77 FR 43002 - Hazardous Waste Management System: Identification and Listing of Hazardous Waste Amendment

Science.gov (United States)

2012-07-23

... ConocoPhillips filter press processing of storm water Billings Refinery). tank sludge (F037) generated at... residual solids from the processed storm water tank sludge meet the delisting levels in 40 CFR 261 Appendix... ENVIRONMENTAL PROTECTION AGENCY 40 CFR Part 261 [FRL 9704-1] Hazardous Waste Management System...

Statistical inference on residual life

CERN Document Server

Jeong, Jong-Hyeon

2014-01-01

This is a monograph on the concept of residual life, which is an alternative summary measure of time-to-event data, or survival data. The mean residual life has been used for many years under the name of life expectancy, so it is a natural concept for summarizing survival or reliability data. It is also more interpretable than the popular hazard function, especially for communications between patients and physicians regarding the efficacy of a new drug in the medical field. This book reviews existing statistical methods to infer the residual life distribution. The review and comparison includes existing inference methods for mean and median, or quantile, residual life analysis through medical data examples. The concept of the residual life is also extended to competing risks analysis. The targeted audience includes biostatisticians, graduate students, and PhD (bio)statisticians. Knowledge in survival analysis at an introductory graduate level is advisable prior to reading this book.

Electrodialytic remediation of air pollution control residues in bench scale

DEFF Research Database (Denmark)

Jensen, Pernille Erland; Ferreira, Celia; Hansen, Henrik K.

2008-01-01

Air pollution control (APC) residue from municipal solid waste incineration (MSWI) is considered a hazardous waste due to its alkalinity and high content of salts and mobile heavy metals. Various solutions for the handling of APC-residue exist in different regions; however, most commercial soluti...

Characterisation and management of concrete grinding residuals.

Science.gov (United States)

Kluge, Matt; Gupta, Nautasha; Watts, Ben; Chadik, Paul A; Ferraro, Christopher; Townsend, Timothy G

2018-02-01

Concrete grinding residue is the waste product resulting from the grinding, cutting, and resurfacing of concrete pavement. Potential beneficial applications for concrete grinding residue include use as a soil amendment and as a construction material, including as an additive to Portland cement concrete. Concrete grinding residue exhibits a high pH, and though not hazardous, it is sufficiently elevated that precautions need to be taken around aquatic ecosystems. Best management practices and state regulations focus on reducing the impact on such aquatic environment. Heavy metals are present in concrete grinding residue, but concentrations are of the same magnitude as typically recycled concrete residuals. The chemical composition of concrete grinding residue makes it a useful product for some soil amendment purposes at appropriate land application rates. The presence of unreacted concrete in concrete grinding residue was examined for potential use as partial replacement of cement in new concrete. Testing of Florida concrete grinding residue revealed no dramatic reactivity or improvement in mortar strength.

Recycling of hazardous solid waste material using high-temperature solar process heat

Energy Technology Data Exchange (ETDEWEB)

Schaffner, B.; Meier, A.; Wuillemin, D.; Hoffelner, W.; Steinfeld, A.

2003-03-01

A novel high-temperature solar chemical reactor is proposed for the thermal recycling of hazardous solid waste material using concentrated solar power. A 10 kW solar reactor prototype was designed and tested for the carbothermic reduction of electric arc furnace dusts (EAFD). The reactor was subjected to mean solar flux intensities of 2000 kW/m2 and operated in both batch and continuous mode within the temperature range 1120-1400 K. Extraction of up to 99% and 90% of the Zn originally contained in the EAFD was achieved in the residue for the batch and continuous solar experiments, respectively. The condensed off-gas products consisted mainly of Zn, Pb, and Cl. No ZnO was detected when the O{sub 2} concentration remained below 2 vol.-%. The use of concentrated solar energy as the source of process heat offers the possibility of converting hazardous solid waste material into valuable commodities for processes in closed and sustainable material cycles. (author)

Microseismic Precursory Characteristics of Rock Burst Hazard in Mining Areas Near a Large Residual Coal Pillar: A Case Study from Xuzhuang Coal Mine, Xuzhou, China

Science.gov (United States)

Cao, An-ye; Dou, Lin-ming; Wang, Chang-bin; Yao, Xiao-xiao; Dong, Jing-yuan; Gu, Yu

2016-11-01

Identification of precursory characteristics is a key issue for rock burst prevention. The aim of this research is to provide a reference for assessing rock burst risk and determining potential rock burst risk areas in coal mining. In this work, the microseismic multidimensional information for the identification of rock bursts and spatial-temporal pre-warning was investigated in a specific coalface which suffered high rock burst risk in a mining area near a large residual coal pillar. Firstly, microseismicity evolution prior to a disastrous rock burst was qualitatively analysed, and the abnormal clustering of seismic sources, abnormal variations in daily total energy release, and event counts can be regarded as precursors to rock burst. Secondly, passive tomographic imaging has been used to locate high seismic activity zones and assess rock burst hazard when the coalface passes through residual pillar areas. The results show that high-velocity or velocity anomaly regions correlated well with strong seismic activities in future mining periods and that passive tomography has the potential to describe, both quantitatively and periodically, hazardous regions and assess rock burst risk. Finally, the bursting strain energy index was further used for short-term spatial-temporal pre-warning of rock bursts. The temporal sequence curve and spatial contour nephograms indicate that the status of the danger and the specific hazardous zones, and levels of rock burst risk can be quantitatively and rapidly analysed in short time and in space. The multidimensional precursory characteristic identification of rock bursts, including qualitative analysis, intermediate and short-time quantitative predictions, can guide the choice of measures implemented to control rock bursts in the field, and provides a new approach to monitor and forecast rock bursts in space and time.

Acid transformation of bauxite residue: Conversion of its alkaline characteristics

OpenAIRE

Kong, X.; Li, M.; Xue, S.; Hartley, W.; Chen, C.; Wu, C.; Li, X.; Li, Y.

2016-01-01

Bauxite residue (BR) is a highly alkaline solid hazardous waste produced from bauxite processing for alumina production. Alkaline transformation appears to reduce the environmental risk of bauxite residue disposal areas (BRDAs) whilst potentially providing opportunities for the sustainable reuse and on-going management of BR. Mineral acids, a novel citric acid and a hybrid combination of acid-gypsum treatments were investigated for their potential to reduce residue pH and total alkalinity and...

Proceedings of emerging technologies for hazardous waste management

International Nuclear Information System (INIS)

Tedder, D.W.

1992-01-01

This book contains proceedings of emerging technologies for hazardous waste management. Topics covered include: Low-temperature oxidation of organic chemical wastes; Advanced waste minimization strategies; Treatment of manufactured gas plant (MGP) and similar wastes; Bioremediation of soils and sediments; Advances in radioactive waste treatment; Computer aides approaches to hazardous waste management; Advances in soil remediation; Low-temperature oxidation of organic chemical waste; Boremediation: Micro, meso, and macro-scale processes; In situ remediation techniques; Treatment of hazardous organics with radiation or solar energy; Technologies for management of municipal waste combustion residues; Environmental restoration and waste management; and Advanced separation and stabilization technologies

Regression models for the restricted residual mean life for right-censored and left-truncated data

DEFF Research Database (Denmark)

Cortese, Giuliana; Holmboe, Stine A.; Scheike, Thomas H.

2017-01-01

The hazard ratios resulting from a Cox's regression hazards model are hard to interpret and to be converted into prolonged survival time. As the main goal is often to study survival functions, there is increasing interest in summary measures based on the survival function that are easier to inter......The hazard ratios resulting from a Cox's regression hazards model are hard to interpret and to be converted into prolonged survival time. As the main goal is often to study survival functions, there is increasing interest in summary measures based on the survival function that are easier...... to interpret than the hazard ratio; the residual mean time is an important example of those measures. However, because of the presence of right censoring, the tail of the survival distribution is often difficult to estimate correctly. Therefore, we consider the restricted residual mean time, which represents...... a partial area under the survival function, given any time horizon τ, and is interpreted as the residual life expectancy up to τ of a subject surviving up to time t. We present a class of regression models for this measure, based on weighted estimating equations and inverse probability of censoring weighted...

Hazardous industrial waste management

International Nuclear Information System (INIS)

Quesada, Hilda; Salas, Juan Carlos; Romero, Luis Guillermo

2007-01-01

The appropriate managing of hazardous wastes is a problem little dealed in the wastes management in the country. A search of available information was made about the generation and handling to internal and external level of the hazardous wastes by national industries. It was worked with eleven companies of different types of industrial activities for, by means of a questionnaire, interviews and visits, to determine the degree of integral and suitable handling of the wastes that they generate. It was concluded that exist only some isolated reports on the generation of hazardous industrial wastes and handling. The total quantity of wastes generated in the country was impossible to establish. The companies consulted were deficient in all stages of the handling of their wastes: generation, accumulation and storage, transport, treatment and final disposition. The lack of knowledge of the legislation and of the appropriate managing of the wastes is showed as the principal cause of the poor management of the residues. The lack of state or private entities entrusted to give services of storage, transport, treatment and final disposition of hazardous wastes in the country was evident. (author) [es

Determination of neomycin residues in pasteurized milks produced in some dairy processing establishments in East-Azarbaijan Province, Iran

Directory of Open Access Journals (Sweden)

M.H Movassagh

2014-11-01

Full Text Available Antibiotic residues in milk have a potential hazard for the consumer and may cause allergic reactions, interference in the intestinal flora that result in development of resistant populations of bacteria, thereby rendering antibiotic treatment ineffective. The aim of this study was to determine neomycin residues in pasteurized milk in East-Azarbaijan province. For this, a total of 200 samples of pasteurized milk produced by five dairy processing establishments of East Azarbaijan province was randomly collected. The samples were obtained over the spring and autumn (100 samples for each season of 2010. First, antibiotic residues were determined by Copan milk test. Afterwards, the competitive ELISA assay was used for the determination of neomycin concentration in positive samples. Of all samples, neomycin residues were observed in 9 and 13 samples and the mean neomycin residues amount were 43.20 ± 8.10 and 26.63±2.08 µg/L in spring and autumn, respectively. According to the limit of neomycin (1500 µg/l in cow raw milk in Iran, despite all the remaining drugs in pasteurized milk, in any of the samples exceeded level of neomycin was not observed.Based on the results, continuousmonitoringofantibiotic residues inmilk samples is recommended.

Effects of Adopting Different Kinds of Collecting Method for Years on Film Residual Coefficient and Maize Yields

Directory of Open Access Journals (Sweden)

TANG Wen-xue

2017-03-01

Full Text Available Wide usage of mulching technology has increased crop yields, but the large amounts of mulching film residue resulting from widespread use of plastic film in China has brought about a series of pollution hazards. Based on a 4-year (2011-2014 long-term experiment, the effects of different kinds of collecting mothod (zero plastic film residues, conventional plastic film residues, whole plastic film residues remainded on plastic film residues, residual coefficient and maize yield were explored. Plastic film residues mainly remained in 0~10 cm, 10~20 cm soil layers. In 0~30 cm soil layers, the two types of mulch residues (>25 cm2, 4~25 cm2 under zero plastic film residues treatment were much less than conventional plastic film residues and whole plastic film residues remainded treatments, no significant differences were observed in the mulch residues (2 among 3 treatments. After maize harvest, the amount of plastic film residues under zero plastic film residues, conventional plastic film residues and whole plastic film residues remainded treatments were 52.71, 80.85 kg·hm-2 and 152.65 kg·hm-2, respectively, the residual coefficient for zero plastic film residues, conventional plastic film residues and whole plastic film residues remainded treatments were -9.45%, 8.53% and 54.42%, respectively. The stem diameter, ear length, ear width, ear row number, grain number per row and 100-grain weight of maize decreased with the increase of residual film amount. Compared with the conventional plastic film residues, the mean grain yield of whole plastic film residues remainded treatment decreased by 15.08%, whereas the zero plastic film residues treatment increased by 4.70%. The plastic film residues, residual coefficient and maize yield were comprehensively analyzed, the conventional plastic film residues practice should be adopted currently without appropriate plastic film residues collector. But from the long-term development, we should speed up the

A New Seismic Hazard Model for Mainland China

Science.gov (United States)

Rong, Y.; Xu, X.; Chen, G.; Cheng, J.; Magistrale, H.; Shen, Z. K.

2017-12-01

We are developing a new seismic hazard model for Mainland China by integrating historical earthquake catalogs, geological faults, geodetic GPS data, and geology maps. To build the model, we construct an Mw-based homogeneous historical earthquake catalog spanning from 780 B.C. to present, create fault models from active fault data, and derive a strain rate model based on the most complete GPS measurements and a new strain derivation algorithm. We divide China and the surrounding regions into about 20 large seismic source zones. For each zone, a tapered Gutenberg-Richter (TGR) magnitude-frequency distribution is used to model the seismic activity rates. The a- and b-values of the TGR distribution are calculated using observed earthquake data, while the corner magnitude is constrained independently using the seismic moment rate inferred from the geodetically-based strain rate model. Small and medium sized earthquakes are distributed within the source zones following the location and magnitude patterns of historical earthquakes. Some of the larger earthquakes are distributed onto active faults, based on their geological characteristics such as slip rate, fault length, down-dip width, and various paleoseismic data. The remaining larger earthquakes are then placed into the background. A new set of magnitude-rupture scaling relationships is developed based on earthquake data from China and vicinity. We evaluate and select appropriate ground motion prediction equations by comparing them with observed ground motion data and performing residual analysis. To implement the modeling workflow, we develop a tool that builds upon the functionalities of GEM's Hazard Modeler's Toolkit. The GEM OpenQuake software is used to calculate seismic hazard at various ground motion periods and various return periods. To account for site amplification, we construct a site condition map based on geology. The resulting new seismic hazard maps can be used for seismic risk analysis and management.

Research on Toxicity Evaluation of Waste Incineration Residues of Printed Circuit Boards

Directory of Open Access Journals (Sweden)

Rasa Volungevičienė

2014-10-01

Full Text Available Recycling waste printed circuit boards (PCB is an extremely complicated process, because PCBs consist of a number of complex components – hazardous and non-hazardous materials sets. Pyrolysis and combustion are currently the most effective treatment technologies for waste printed circuit boards. Pyrolysis can be used for thermally decomposing PCBs allowing for the simultaneous recovery of valuable materials. Following the extraction of valuable materials, the problem of residual ash utilization is encountered. Determining the qualitative and quantitative characteristics of incineration residue helps with choosing effective ash management technologies. This paper analyzes PCB ash generated at three different temperatures of 400 °C, 500 °C and 600 °C. Ash residues have been analysed to determine the quantity and type of metals present. Furthermore, the experiment of leaching heavy metals from ash has been described.

Functional form diagnostics for Cox's proportional hazards model.

Science.gov (United States)

León, Larry F; Tsai, Chih-Ling

2004-03-01

We propose a new type of residual and an easily computed functional form test for the Cox proportional hazards model. The proposed test is a modification of the omnibus test for testing the overall fit of a parametric regression model, developed by Stute, González Manteiga, and Presedo Quindimil (1998, Journal of the American Statistical Association93, 141-149), and is based on what we call censoring consistent residuals. In addition, we develop residual plots that can be used to identify the correct functional forms of covariates. We compare our test with the functional form test of Lin, Wei, and Ying (1993, Biometrika80, 557-572) in a simulation study. The practical application of the proposed residuals and functional form test is illustrated using both a simulated data set and a real data set.

Obtention of ceramic pigments with residue from electroplating

International Nuclear Information System (INIS)

Boss, A.; Kniess, C.T.; Aguiar, B.M. de; Prates, P.B.; Milanez, K.

2011-01-01

The incorporation of industrial residues in industrial processes opens up new business opportunities and reduces the volume of extraction of raw materials, preserving natural resources, which are limited. An important residue is the mud from galvanic industry, consisting of alkali and transition metals. According to NBR 10004/2004, this residue can be classified as Class I (hazardous), depending on the concentration of metals present in the mud. This paper proposes a method for reusing the residue from electroplating in ceramic pigments. The characterization of residual plating was obtained by chemical analysis, mineralogical analysis and pH measurements. The electroplating waste was incorporated in different percentages on a standard pigment formula of industrial ceramic, consisting mainly of Zn, Fe and Cr. The obtained pigments were applied in ceramic glazes to colorimetric and visual analysis, which showed good results with the addition of up to 15% of industrial waste. (author)

Contribution of microorganisms to non-extractable residue formation during biodegradation of ibuprofen in soil

Energy Technology Data Exchange (ETDEWEB)

Nowak, Karolina M., E-mail: karolina.nowak@ufz.de [UFZ, Helmholtz Centre for Environmental Research, Department of Environmental Biotechnology, Permoserstraße 15, 04318 Leipzig (Germany); Department of Environmental Biology and Chemodynamics, Institute for Environmental Research (Biology V), RWTH Aachen University, Worringerweg 1, 52074 Aachen (Germany); Girardi, Cristobal; Miltner, Anja [UFZ, Helmholtz Centre for Environmental Research, Department of Environmental Biotechnology, Permoserstraße 15, 04318 Leipzig (Germany); Gehre, Matthias [UFZ, Helmholtz Centre for Environmental Research, Department of Isotope Biogeochemistry, Permoserstraße 15, 04318 Leipzig (Germany); Schäffer, Andreas [Department of Environmental Biology and Chemodynamics, Institute for Environmental Research (Biology V), RWTH Aachen University, Worringerweg 1, 52074 Aachen (Germany); Kästner, Matthias [UFZ, Helmholtz Centre for Environmental Research, Department of Environmental Biotechnology, Permoserstraße 15, 04318 Leipzig (Germany)

2013-02-15

Non-extractable residues (NER) formed during biodegradation of organic contaminants in soil are considered to be mainly composed of parent compounds or their primary metabolites with hazardous potential. However, in the case of biodegradable organic compounds, the soil NER may also contain microbial biomass components, for example fatty acids (FA) and amino acids (AA). After cell death, these biomolecules are subsequently incorporated into non-living soil organic matter (SOM) and are stabilised ultimately forming hardly extractable residues of biogenic origin. We investigated biodegradation of {sup 13}C{sub 6}-ibuprofen, in particular the metabolic incorporation of the {sup 13}C-label into FA and AA and their fate in soil over 90 days. {sup 13}C-FA and {sup 13}C-AA amounts in the living microbial biomass fraction initially increased, then decreased over time and were continuously incorporated into the non-living SOM pool. The {sup 13}C-FA in the non-living SOM remained stable from day 59 whereas the contents of {sup 13}C-AA slightly increased until the end. After 90 days, nearly all NER were biogenic as they were made up almost completely by natural biomass compounds. The presented data demonstrated that the potential environmental risks related to the ibuprofen-derived NER are overestimated. - Highlights: ► Biogenic residue formation during microbial degradation of ibuprofen was studied. ► Nearly all non-extractable residues derived from ibuprofen were biogenic. ► Fatty acids and amino acids formed biogenic non-extractable residues and were stabilised in soil. ► Environmental risks of ibuprofen-derived non-extractable residues are overestimated.

Contribution of microorganisms to non-extractable residue formation during biodegradation of ibuprofen in soil

International Nuclear Information System (INIS)

Nowak, Karolina M.; Girardi, Cristobal; Miltner, Anja; Gehre, Matthias; Schäffer, Andreas; Kästner, Matthias

2013-01-01

Non-extractable residues (NER) formed during biodegradation of organic contaminants in soil are considered to be mainly composed of parent compounds or their primary metabolites with hazardous potential. However, in the case of biodegradable organic compounds, the soil NER may also contain microbial biomass components, for example fatty acids (FA) and amino acids (AA). After cell death, these biomolecules are subsequently incorporated into non-living soil organic matter (SOM) and are stabilised ultimately forming hardly extractable residues of biogenic origin. We investigated biodegradation of 13 C 6 -ibuprofen, in particular the metabolic incorporation of the 13 C-label into FA and AA and their fate in soil over 90 days. 13 C-FA and 13 C-AA amounts in the living microbial biomass fraction initially increased, then decreased over time and were continuously incorporated into the non-living SOM pool. The 13 C-FA in the non-living SOM remained stable from day 59 whereas the contents of 13 C-AA slightly increased until the end. After 90 days, nearly all NER were biogenic as they were made up almost completely by natural biomass compounds. The presented data demonstrated that the potential environmental risks related to the ibuprofen-derived NER are overestimated. - Highlights: ► Biogenic residue formation during microbial degradation of ibuprofen was studied. ► Nearly all non-extractable residues derived from ibuprofen were biogenic. ► Fatty acids and amino acids formed biogenic non-extractable residues and were stabilised in soil. ► Environmental risks of ibuprofen-derived non-extractable residues are overestimated

Effect of drying on leaching testing of treated municipal solid waste incineration APC-residues

DEFF Research Database (Denmark)

Hu, Y.; Hyks, Jiri; Astrup, Thomas

2008-01-01

Air-pollution-control (APC) residues from waste incinerators are hazardous waste according to European legislation and must be treated prior to landfilling. Batch and column leaching data determine which type of landfill can receive the treated APC-residues. CEN standards are prescribed...

Residual radioactive contamination of the Maralinga range from nuclear weapons tests conducted in 1956 and 1957

International Nuclear Information System (INIS)

Cooper, M.B.; Duggleby, J.C.; Kotler, L.H.; Wise, K.N.

1978-12-01

Detailed geographical distributions and concentrations of long-lived radionuclides remaining from the major trials of nuclear weapons conducted at Maralinga in 1956 and 1957 are presented. It is shown that residual contamination due to fission products - mainly strontium-90, caesium-137 and europium-155 - are well below levels that could constitute a health hazard to occupants of the area. In the regions near the ground zeroes however, long-lived neutron activation products in soil - mainly cobalt-60 and europium-152 - are present in sufficient abundance to give rise to gamma-radiation dose-rates up to 2 milliroentgen per hour, which exceed maximum recommended dose-rates for continuous occupancy

Potential hazard by toxic substances in foods. Environmental protection

Energy Technology Data Exchange (ETDEWEB)

Unterhalt, B

1974-01-01

This paper reviews various toxic substances found in foods. These toxic substances include not only natural occurring toxins but also bacterial food poisons, pesticide residues, heavy metals, and food additives. The potential hazard of each toxic substance is discussed. 74 references.

Predicting the residual life of plant equipment - Why worry

International Nuclear Information System (INIS)

Jaske, C.E.

1985-01-01

Predicting the residual life of plant equipment that has been in service for 20 to 30 years or more is a major concern of many industries. This paper reviews the reasons for increased concern for residual-life assessment and the general procedures used in performing such assessments. Some examples and case histories illustrating procedures for assessing remaining service life are discussed. Areas where developments are needed to improve the technology for remaining-life estimation are pointed out. Then, some of the critical issues involved in residual-life assessment are identified. Finally, the future role of residual-life prediction is addressed

Improving sensitivity of residual current transformers to high frequency earth fault currents

Directory of Open Access Journals (Sweden)

Czapp Stanislaw

2017-09-01

Full Text Available For protection against electric shock in low voltage systems residual current devices are commonly used. However, their proper operation can be interfered when high frequency earth fault current occurs. Serious hazard of electrocution exists then. In order to detect such a current, it is necessary to modify parameters of residual current devices, especially the operating point of their current transformer. The authors proposed the modification in the structure of residual current devices. This modification improves sensitivity of residual current devices when high frequency earth fault current occurs. The test of the modified residual current device proved that the authors’ proposition is appropriate.

Environmental and occupational hazards associated with decontamination solutions (a)

International Nuclear Information System (INIS)

Levanthal, L.

1985-01-01

Some of the reagents employed in the decontamination of reactor coolant systems are potentially hazardous. Potential exposure to decontamination agents by operating personnel, or members of the general population, could occur during use, processing, transportation to, or disposal at a low-level waste site. Federal and state agencies have promulgated regulations relevant to the disposal of decontamination solution waste to prevent acute or chronic exposures. In particular, the Nuclear Regulatory Commission (NRC), U.S. Environmental Protection Agency (EPA), Department of Transportation (DOT), Department of Labor - Occupational Safety and Health Administration (OSHA), State of South Carolina, State of Nevada, and the State of Washington have such regulations. These regulations may impact on the choice of decontamination solutions, operations procedures, processing methods, or disposal methods. Laws and regulations relate to both chemically hazardous, or toxic materials and to radioactive hazards. Laws which regulate the exposure of workers and the general public to effluents and emissions during processing, disposal and transport have been abstracted. As a result of these regulations, utilities are required to obtain permits to perform monitoring and sampling of personnel and the on-site and off-site environment, provide proper protective clothing and ventilation, make certain the solutions are properly contained during use, storage and processing, and destroy and/or properly immobilize the residues for disposal. Waste treatment processes such as neutralization, ion exchange, evaporation, incineration, etc., must not produce, nor result in hazardous emissions, effluents, residues, or hazards to workers. The laws also stipulate record keeping and documentation

Prevalence, Predictors and Clinical Outcome of Residual Pulmonary Hypertension Following Tricuspid Annuloplasty.

Science.gov (United States)

Chen, Yan; Liu, Ju-Hua; Chan, Daniel; Sit, Ko-Yung; Wong, Chun-Ka; Ho, Kar-Lai; Ho, Lai-Ming; Zhen, Zhe; Lam, Yui-Ming; Lau, Chu-Pak; Au, Wing-Kok; Tse, Hung-Fat; Yiu, Kai-Hang

2016-07-22

Tricuspid annuloplasty is increasingly performed during left heart valve surgery, but the long-term clinical outcome postoperatively is not satisfactory. The aim of this study was to determine whether residual pulmonary hypertension (PHT) contributes to the adverse outcome. One-hundred thirty-seven patients (age 61±11 years; men, 30%) who underwent tricuspid annuloplasty during left-side valve surgery were enrolled. The mean pulmonary artery systolic pressure before surgery was 49±13 mm Hg and 32±15 mm Hg following surgery. Patients were divided into 3 groups according to postoperative pulmonary artery systolic pressure: no residual PHT (n=78, 57%), mild residual PHT (n=43, 31%), or significant residual PHT (n=16, 12%). A preoperative larger right ventricular (RV) geometry and tricuspid valve tethering area were associated with mild or significant residual PHT. A total of 24 adverse events (20 heart failures and 4 cardiovascular deaths) occurred during a median follow-up of 25 months. Kaplan-Meier survival curve demonstrated that patients with significant residual PHT had the highest percentage of adverse events followed by those with mild residual PHT. Patients with no residual PHT had a very low risk of adverse events. Multivariable Cox regression analysis revealed that both mild (hazard ratio=4.94; 95% CI =1.34-18.16; P=0.02) and significant residual PHT (hazard ratio=8.67; 95% CI =2.43-30.98; P<0.01) were independent factors associated with adverse events. The present study demonstrated that 43% of patients who underwent tricuspid annuloplasty had residual PHT. The presence of mild or significant residual PHT was associated with adverse events in these patients. © 2016 The Authors. Published on behalf of the American Heart Association, Inc., by Wiley Blackwell.

Hazardous constituent source term. Revision 2

International Nuclear Information System (INIS)

1994-01-01

The Department of Energy (DOE) has several facilities that either generate and/or store transuranic (TRU)-waste from weapons program research and production. Much of this waste also contains hazardous waste constituents as regulated under Subtitle C of the Resource Conservation and Recovery Act (RCRA). Toxicity characteristic metals in the waste principally include lead, occurring in leaded rubber gloves and shielding. Other RCRA metals may occur as contaminants in pyrochemical salt, soil, debris, and sludge and solidified liquids, as well as in equipment resulting from decontamination and decommissioning activities. Volatile organic compounds (VOCS) contaminate many waste forms as a residue adsorbed on surfaces or occur in sludge and solidified liquids. Due to the presence of these hazardous constituents, applicable disposal regulations include land disposal restrictions established by Hazardous and Solid Waste Amendments (HSWA). The DOE plans to dispose of TRU-mixed waste from the weapons program in the Waste Isolation Pilot Plant (WIPP) by demonstrating no-migration of hazardous constituents. This paper documents the current technical basis for methodologies proposed to develop a post-closure RCRA hazardous constituent source term. For the purposes of demonstrating no-migration, the hazardous constituent source term is defined as the quantities of hazardous constituents that are available for transport after repository closure. Development of the source term is only one of several activities that will be involved in the no-migration demonstration. The demonstration will also include uncertainty and sensitivity analyses of contaminant transport

Effects of Adopting Different Kinds of Collecting Method for Years on Film Residual Coefficient and Maize Yields

OpenAIRE

TANG Wen-xue; MA Zhong-ming; WEI Tao

2017-01-01

Wide usage of mulching technology has increased crop yields, but the large amounts of mulching film residue resulting from widespread use of plastic film in China has brought about a series of pollution hazards. Based on a 4-year (2011-2014) long-term experiment, the effects of different kinds of collecting mothod (zero plastic film residues, conventional plastic film residues, whole plastic film residues remainded) on plastic film residues, residual coefficient and maize yield were explored....

Facts about food irradiation: Irradiation and food additives and residues

International Nuclear Information System (INIS)

1991-01-01

This fact sheet considers the issue of the irradiation of food containing food additives or pesticide residues. The conclusion is that there is no health hazard posed by radiolytic products of pesticides or food additives. 1 ref

Fact Sheet for Friction Materials Manufacturing Facilities Residual Risk and Technology Review

Science.gov (United States)

proposed amendments to the National Emission Standards for Hazardous Air Pollutants (NESHAP) for Friction Materials Manufacturing Facilities to address the results of the residual risk and technology review

Hazard Classification for Fuel Supply Shutdown Facility

International Nuclear Information System (INIS)

BENECKE, M.W.

2000-01-01

Final hazard classification for the 300 Area N Reactor fuel storage facility resulted in the assignment of Nuclear Facility Hazard Category 3 for the uranium metal fuel and feed material storage buildings (303-A, 303-B, 303-G, 3712, and 3716). Radiological for the residual uranium and thorium oxide storage building and an empty former fuel storage building that may be used for limited radioactive material storage in the future (303-K/3707-G, and 303-E), and Industrial for the remainder of the Fuel Supply Shutdown buildings (303-F/311 Tank Farm, 303-M, 313-S, 333, 334 and Tank Farm, 334-A, and MO-052)

40 CFR Appendix Viii to Part 266 - Organic Compounds for Which Residues Must Be Analyzed

Science.gov (United States)

2010-07-01

... AGENCY (CONTINUED) SOLID WASTES (CONTINUED) STANDARDS FOR THE MANAGEMENT OF SPECIFIC HAZARDOUS WASTES AND SPECIFIC TYPES OF HAZARDOUS WASTE MANAGEMENT FACILITIES Pt. 266, App. VIII Appendix VIII to Part 266... 40 Protection of Environment 26 2010-07-01 2010-07-01 false Organic Compounds for Which Residues...

Preliminary Hazard Classification for the Remediation of the 100-B/C Area Remaining Sites (Confirmatory Sampling Effort)

International Nuclear Information System (INIS)

Routt, T.M.

2000-01-01

This document provides the preliminary hazard classification for the sampling and characterization activities to be conducted at the 100-B/C confirmatory sampling effort sites in support of remedial design and eventual remediation of these sites

Pasteurised milk and implementation of HACCP (Hazard Analysis Critical Control Point

Directory of Open Access Journals (Sweden)

T.B Murdiati

2004-10-01

Full Text Available The purpose of pasteurisation is to destroy pathogen bacteria without affecting the taste, flavor, and nutritional value. A study on the implementation of HACCP (Hazard Analysis Critical Control Point in producing pasteurized milk was carried out in four processing unit of pasteurised milk, one in Jakarta, two in Bandung and one in Bogor. The critical control points in the production line were identified. Milk samples were collected from the critical points and were analysed for the total number of microbes. Antibiotic residues were detected on raw milks. The study indicated that one unit in Bandung dan one unit in Jakarta produced pasteurized milk with lower number of microbes than the other units, due to better management and control applied along the chain of production. Penisilin residues was detected in raw milk used by unit in Bogor. Six critical points and the hazard might arise in those points were identified, as well as how to prevent the hazards. Quality assurance system such as HACCP would be able to produce high quality and safety of pasteurised milk, and should be implemented gradually.

Mixed-waste treatment -- What about the residuals?

International Nuclear Information System (INIS)

Carlson, T.; Carpenter, C.; Cummins, L.; Haas, P.; MacInnis, J.; Maxwell, C.

1993-01-01

Incineration currently is the best demonstrated available technology for the large inventory of U.S. Department of Energy (DOE) mixed waste. However, molten salt oxidation (MSO) is an alternative thermal treatment technology with the potential to treat a number of these wastes. Of concern for both technologies is the final waste forms, or residuals, that are generated by the treatment process. An evaluation of the two technologies focuses on 10 existing DOE waste streams and current hazardous-waste regulations, specifically for the delisting of ''derived-from'' residuals. Major findings include that final disposal options are more significantly impacted by the type of waste treated and existing regulations than by the type of treatment technology; typical DOE waste streams are not good candidates for delisting; and mass balance calculations indicate that MSO and incineration generate similar quantities (dry) and types of residuals

Small WEEE: determining recyclables and hazardous substances in plastics.

Science.gov (United States)

Dimitrakakis, Emmanouil; Janz, Alexander; Bilitewski, Bernd; Gidarakos, Evangelos

2009-01-30

An examination regarding the determination of recyclables and hazardous substances in small waste electrical and electronic equipment (WEEE) found in the residual household waste stream of the city of Dresden, Germany, is described. Firstly, attitudes towards the disposal of small WEEE in the latter are assessed, and product types and categories which mostly contribute to its composition are identified. Physical parameters which could be used as mechanical sorting criteria are measured, and the material composition of the small WEEE found is determined. The hazardous substances' "base" charge in the residual waste is established by means of atomic absorption spectrometry and ionic chromatography, as a first step in estimating the contribution of small WEEE to its pollutant load. Consequently, the content of small WEEE plastics in key heavy metals and halogens is determined. Key conclusions are drawn concerning the future strategic development and practical implementation of the 2002/96/EC Directive, in relation to small WEEE management and recycling.

Small WEEE: Determining recyclables and hazardous substances in plastics

International Nuclear Information System (INIS)

Dimitrakakis, Emmanouil; Janz, Alexander; Bilitewski, Bernd; Gidarakos, Evangelos

2009-01-01

An examination regarding the determination of recyclables and hazardous substances in small waste electrical and electronic equipment (WEEE) found in the residual household waste stream of the city of Dresden, Germany, is described. Firstly, attitudes towards the disposal of small WEEE in the latter are assessed, and product types and categories which mostly contribute to its composition are identified. Physical parameters which could be used as mechanical sorting criteria are measured, and the material composition of the small WEEE found is determined. The hazardous substances' 'base' charge in the residual waste is established by means of atomic absorption spectrometry and ionic chromatography, as a first step in estimating the contribution of small WEEE to its pollutant load. Consequently, the content of small WEEE plastics in key heavy metals and halogens is determined. Key conclusions are drawn concerning the future strategic development and practical implementation of the 2002/96/EC Directive, in relation to small WEEE management and recycling

Use of residual hydrocarbons treated by Thermal Plasma (recovery of energy by-products)

International Nuclear Information System (INIS)

Carreno B, J.A.; Pacheco S, J.O.; Ramos F, F.; Cruz A, A.; Duran G, M.

2001-01-01

The emergence of new technologies is getting greater importance for the control of pollution. One of them is the destruction of hazardous wastes treated by thermal plasma, which is of special interest for the efficient treatment of the hazardous wastes since the heat generated by thermal plasma is able to destroy the molecular bonds generating solids and gaseous products which do not represent danger for the human being and the environment. The thermal plasma is the suitable technology for treating a wide range of hazardous wastes, including the residual hydrocarbons from the refinement process of petroleum, plasma exceeds the barrier of 3000 Centigrade. The efficiency of the degradation of residues is greater than 99.99%. Toxic emissions are not generated to environment as SO 2 , NO x and CO 2 neither dioxins and furans by being a pyrolysis process. The use of hydrogen as fuel does not generate pollution to environment. (Author)

40 CFR Appendix Vii to Part 266 - Health-Based Limits for Exclusion of Waste-Derived Residues*

Science.gov (United States)

2010-07-01

... Waste-Derived Residues* VII Appendix VII to Part 266 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) SOLID WASTES (CONTINUED) STANDARDS FOR THE MANAGEMENT OF SPECIFIC HAZARDOUS WASTES AND SPECIFIC TYPES OF HAZARDOUS WASTE MANAGEMENT FACILITIES Pt. 266, App. VII Appendix VII to Part 266—Health...

Environmental dredging residual generation and management.

Science.gov (United States)

Patmont, Clay; LaRosa, Paul; Narayanan, Raghav; Forrest, Casey

2018-05-01

The presence and magnitude of sediment contamination remaining in a completed dredge area can often dictate the success of an environmental dredging project. The need to better understand and manage this remaining contamination, referred to as "postdredging residuals," has increasingly been recognized by practitioners and investigators. Based on recent dredging projects with robust characterization programs, it is now understood that the residual contamination layer in the postdredging sediment comprises a mixture of contaminated sediments that originate from throughout the dredge cut. This mixture of contaminated sediments initially exhibits fluid mud properties that can contribute to sediment transport and contamination risk outside of the dredge area. This article reviews robust dredging residual evaluations recently performed in the United States and Canada, including the Hudson River, Lower Fox River, Ashtabula River, and Esquimalt Harbour, along with other projects. These data better inform the understanding of residuals generation, leading to improved models of dredging residual formation to inform remedy evaluation, selection, design, and implementation. Data from these projects confirm that the magnitude of dredging residuals is largely determined by site conditions, primarily in situ sediment fluidity or liquidity as measured by dry bulk density. While the generation of dredging residuals cannot be avoided, residuals can be successfully and efficiently managed through careful development and implementation of site-specific management plans. Integr Environ Assess Manag 2018;14:335-343. © 2018 The Authors. Integrated Environmental Assessment and Management Published by Wiley Periodicals, Inc. on behalf of Society of Environmental Toxicology & Chemistry (SETAC). © 2018 The Authors. Integrated Environmental Assessment and Management Published by Wiley Periodicals, Inc. on behalf of Society of Environmental Toxicology & Chemistry (SETAC).

Residual radioactive contamination at Maralinga and Emu, 1985

International Nuclear Information System (INIS)

Lokan, K.H.

1985-04-01

An account is provided of residual contamination at Maralinga and Emu, in South Australia, where the United Kingdom Atomic Weapons Research Establishment conducted nuclear weapons development trials between 1953 and 1963. Detailed information is presented about contamination levels at sites on the range where radioactive materials were dispersed. Some of these were associated with trials involving natural uranium or short-lived isotopes which are no longer present. There are four sites where plutonium-239 was dispersed in substantial quantities from minor trials and information is presented about its distribution. Much of this material has been diluted by mixing with local soil, but there is a significant quantity of material present in the form of contaminated fragments, particularly at Taranaki. A considerable quantity of uranium-235 is also present at Taranaki. An assessment is made of the radiological significance of the dispersed plutonium and it is concluded that the material represents a potential long term hazard while it remains in its present form. Residual radioactivity associated with all but one of the seven major trial sites involving nuclear explosions continues to decay in a predictable way and will in the worst case, fall below levels considered safe for continuous occupancy within about fifty years. One site, Tadje, contains significant concentrations of plutonium over a small area and onsidered to be an additional plutonium-contaminated locality. Measurements of beryllium concentrations in soil are presented

Instructive of chemical residues waste administration

International Nuclear Information System (INIS)

Alfaro Vargas, Ariel

2014-01-01

An instructive is established for the waste management system of chemical residues generated at the Universidad de Costa Rica, ensuring the collection, separation, transportation, reuse, recycling and final disposal. The laboratory waste management system is conditioned to the volume and type of waste generated. The respective procedures are listed in data sheets according to the corresponding model: avoid, reduce, recycle, treat, delete. The materials are identified as: expired products, materials or damaged products, substances that have lost some of the required characteristics, waste from the regular activities of the lab, unused products that now no longer used because they are considered inadequate. The chemicals reagents or hazardous are transformed into small amounts of derivatives safe products, or less hazardous, to allow for removal or to pick up a spill of these without problem [es

Sedentary behavior and residual-specific mortality

OpenAIRE

Paul D. Loprinzi; Meghan K. Edwards; Eveleen Sng; Ovuokerie Addoh

2016-01-01

Background: The purpose of this study was to examine the association of accelerometer-assessed sedentary behavior and residual-specific mortality. Methods: Data from the 2003-2006 National Health and Nutrition Examination Survey (NHANES) were used (N = 5536), with follow-up through 2011. Sedentary behavior was objectively measured over 7 days via accelerometry. Results: When expressing sedentary behavior as a 60 min/day increase, the hazard ratio across the models ranged from 1.07-1.40 (P < 0...

Radiotracer studies on the fate and transformation of pesticide residues in the environment and food chains. Part of a coordinated programme on isotopic-tracer-aided studies of chemical residues in cotton seed, feed, oil and related products

International Nuclear Information System (INIS)

Lee, S.R.

1980-10-01

The magnitude and fate of some pesticide chemicals in Korean foods were studied with particular reference to oil-bearing crops and related products. Application of the chemicals was made under conditions of actual agricultural practice. Analytical methodologies included nuclear activation, gas chromatographic, spectrophotometric and radiotracer techniques. Residues of benzene hexachloride, heptachlor, heptachlor epoxide, aldrin, dieldrin, endrin and DDT found in refined vegetable oil samples were below or within the tolerance limits set by international organizations and as such, these are unlikely to present any toxicological hazard to the consumer. Also, residues of the herbicides nitrogen, alachlor and butachlor applied to oil-bearing crops were not detected in the seeds. Studies on 14 C-BHC residues in rice revealed that polishing and washing play an important role in removing a considerable portion of the residue. Data on the arsenic-containing neoasozine residues suggest that the products consumed by the human (grain and oil) contained residues below the tolerance limit and are unlikely to present any toxicological hazard to the consumer. On the other hand, relatively high arsenic concentrations (2.2 mg/kg) were found in the cake (serving as animal feed) and should be carefully evaluated in the light of toxicological data

Persistence of pirimiphos methyl residues in stored wheat

International Nuclear Information System (INIS)

Zennouche, B.; Bennaceur, M.

1991-03-01

The persistence of 14C pirimiphos methyl in stored wheat was investigated under local conditions during a storage period of 6 months. Surface, methanol extractable and bound residues were quantified. There was a gradual increase in the surface residues over the storage period. 27,97% of the applied amount was found in the surface residues and 54,16% in the extractable and bound residues one month after treatment. After 6 months storage, about 17,8% of the total quantity of the applied pirimiphos methyl remained on the surface and about 58,6% was present in the grains (extractable and bound residues). During cooking 10,91% of the extractable and bound residues were lost

Analysis of Infiltration-Suction Response in Unsaturated Residual Soil Slope in Gelugor, Penang

Science.gov (United States)

Ashraf Mohamad Ismail, Mohd; Hasliza Hamzah, Nur; Min, Ng Soon; Hazreek Zainal Abidin, Mohd; Tajudin, Saiful Azhar Ahmad; Madun, Aziman

2018-04-01

Rainfall infiltration on residual soil slope may impair slope stability by altering the pore-water pressure in the soil. A study has been carried out on unsaturated residual soil slope in Gelugor, Penang to determine the changes in matric suction of residual soils at different depth due to rainwater infiltration. The sequence of this study includes the site investigation, field instrumentation, laboratory experiment and numerical modeling. Void ratio and porosity of soil were found to be decreasing with depth while the bulk density and dry density of soil increased due to lower porosity of soil at greater depth. Soil infiltration rate and matric suction of all depths decrease with the increase of volumetric water content as well as the degree of saturation. Numerical modeling was used to verify and predict the relationship between infiltration-suction response and degree of saturation. Numerical models can be used to integrate the rainfall scenarios into quantitative landslide hazard assessments. Thus, development plans and mitigation measures can be designed for estimated impacts from hazard assessments based on collected data.

Vitrification of high-level radioactive and hazardous wastes

International Nuclear Information System (INIS)

Lutze, W.

1993-12-01

The main objective is to summarize work conducted on glasses as waste forms for high-level radioactive fission product solutions up to the late 1980's (section I and II). Section III addresses the question, whether waste forms designed for the immobilization of radioactive residues can be used for the same purpose for hazardous wastes. Of particular interest are those types of hazardous wastes, e.g., fly ashes from municipal combustion plants, easy to convert into glasses or ceramic materials. A large number of base glass compositions has been studied to vitrify waste from reprocessing but only borosilicate glasses with melting temperatures between 1100 C and 1200 C and very good hydrolytic stability is used today. (orig./HP) [de

Analysis of imidacloprid residues in fruits, vegetables, cereals, fruit juices, and baby foods, and daily intake estimation in and around Lucknow, India.

Science.gov (United States)

Kapoor, Upasana; Srivastava, M K; Srivastava, Ashutosh Kumar; Patel, D K; Garg, Veena; Srivastava, L P

2013-03-01

A total of 250 samples-including fruits, fruit juices, and baby foods (50 samples each), vegetables (70 samples), and cereals (30 samples)-were collected from Lucknow, India, and analyzed for the presence of imidacloprid residues. The QuEChERS (quick, easy, cheap, effective, rugged, and safe) method of extraction coupled with high-performance liquid chromatographic analysis were carried out, and imidacloprid residues were qualitatively confirmed by liquid chromatography-mass spectrometry. Imidacloprid was not detected in samples of fruit juices and baby foods. It was, however, detected in 38 samples of fruits, vegetables, and cereals, which is about 15.20% of the total samples. Of samples of fruits, 22% showed the presence of imidacloprid, and 2% of samples showed residues above the maximal residue limit. Although imidacloprid was detected in 24% of vegetable samples, only 5.71% showed the presence of imidacloprid above the maximal residue limit. However, 33% of cereal samples showed the presence of imidacloprid, and about 3% of samples were above the maximal residue limit. The calculated estimated daily intake ranged between 0.004 and 0.131 µg/kg body weight, and the hazard indices ranged from 0.007 to 0.218 for these food commodities. It is therefore indicated that lifetime consumption of vegetables, fruits, fruit juices, baby foods, wheat, rice, and pulses may not pose a health hazard for the population of Lucknow because the hazard indices for imidacloprid residues were below one. Copyright © 2012 SETAC.

BTC method for evaluation of remaining strength and service life of bridge cables.

Science.gov (United States)

2011-09-01

"This report presents the BTC method; a comprehensive state-of-the-art methodology for evaluation of remaining : strength and residual life of bridge cables. The BTC method is a probability-based, proprietary, patented, and peerreviewed : methodology...

Determination of hazardous substances in food basket eggs in Tehran, Iran: A preliminary study

OpenAIRE

Salar-Amoli, Jamileh; Ali-Esfahani, Tahereh

2015-01-01

Extensive distribution of hazardous substances in food chain and the deleterious effect of their residues on public health are a great concern of the society. Chicken eggs, as one of the most popular food commodities, in different parts of Tehran (Iran) were analyzed for two groups of hazardous substances including some organochlorine pesticides (OC) such as aldrin, lindane, dieldrin, dichlorodiphenyltrichloroethane, heptachlor and endusulfan) and heavy metals namely mercury (Hg), arsenic (As...

Assessment of the radiological conditions in areas of Kuwait with residues of depleted uranium

International Nuclear Information System (INIS)

Cabianca, T.; Danesi, P.R.; Linsley, G.

2004-01-01

The 1991 Gulf War was the first conflict in which DU munitions were used extensively. After this conflict, questions arose regarding the possible link between exposure to ionizing radiation from DU and harmful biological effects. In view of these concerns, the Government of Kuwait, in February 2001, requested the IAEA to conduct an assessment to evaluate the possible radiological impact of residues of DU munitions from the 1991 Gulf War at 11 locations in Kuwait. For this purpose, the IAEA assembled a team of senior experts, who visited Kuwait in September 2001 to carry out a preliminary assessment of the sites and to evaluate the available information. In February 2002 scientists from the IAEA, the Spiez Laboratory (Switzerland), representing UNEP, and the Radiation Protection Department of the Ministry of Health of Kuwait, carried out a sampling campaign at these sites. Around 200 environmental samples, including soil, water and vegetation, were collected during the campaign and subsequently analysed. This study constitutes the first comprehensive radiological assessment of compliance with international radiation protection criteria and standards for areas with residues of DU munitions conducted under the auspices of the IAEA. The findings of this investigation indicate that DU does not pose a radiological hazard to the population of Kuwait. Annual radiation doses arising from exposure to DU residues would be of a few micro-sieverts, well below the annual doses from natural sources of radiation and far below the reference level recommended by the IAEA as a criterion to help establish whether remedial actions are necessary. DU penetrators can still be found at some of the locations visited. Prolonged skin contact with these residues is the only possible pathway that could result in exposures of radiological significance. As long as access to these areas remains restricted, the likelihood that members of the public could come into contact with these residues is low

Bioemulsifier production byMicrobacterium SP. strains isolated from mangrove and their application to remove cadmiun and zinc from hazardous industrial residue

Science.gov (United States)

Aniszewski, Erick; Peixoto, Raquel Silva; Mota, Fábio Faria; Leite, Selma Gomes Ferreira; Rosado, Alexandre Soares

2010-01-01

The contamination of ecosystems with heavy metals is an important issue in current world and remediation technologies should be in according to environmental sustainability concept. Bioemulsifier are promising agents to be used in metal removal and could be effective to many applications in environmental industries. The aims of this work was screening the potential production of bioemulsifier by microorganisms isolated from an oil contaminated mangrove, and evaluate cadmium and zinc removal potential of those strains from a hazardous industrial residue. From that, bioemulsifier-producing bacteria were isolated from urban mangrove sediments. Four isolates were identified as Microbacterium sp by 16S rRNA analysis and were able to reduce up to 53.3% of culture medium surface tension (TS) when using glucose as carbon and energy source and 20.2% when sucrose was used. Suspensions containing bioemulsifier produced by Microbacterium sp. strains show to be able to remove cadmium and zinc from contaminated industrial residue, and its ability varied according carbon source. Significant differences in metal removal were observed by all strains depending on the carbon source. When glucose was used, Cd and Zn removal varied from 17 to 41%, and 14 to 68%, respectively. However, when sucrose was used it was observed only 4 to a maximum of 15% of Cd removal, and 4 to 17% of Zn removal. When the same tests were performed after ethanol precipitation, the results were different: the percentages of removal of Zn (7–27%) and Cd (14–32%) were higher from sucrose cultures. This is the first report of heavy metals removal by bioemulsifier from Microbacterium sp. PMID:24031486

Ethanol production from residual wood chips of cellulose industry: acid pretreatment investigation, hemicellulosic hydrolysate fermentation, and remaining solid fraction fermentation by SSF process.

Science.gov (United States)

Silva, Neumara Luci Conceição; Betancur, Gabriel Jaime Vargas; Vasquez, Mariana Peñuela; Gomes, Edelvio de Barros; Pereira, Nei

2011-04-01

Current research indicates the ethanol fuel production from lignocellulosic materials, such as residual wood chips from the cellulose industry, as new emerging technology. This work aimed at evaluating the ethanol production from hemicellulose of eucalyptus chips by diluted acid pretreatment and the subsequent fermentation of the generated hydrolysate by a flocculating strain of Pichia stipitis. The remaining solid fraction generated after pretreatment was subjected to enzymatic hydrolysis, which was carried out simultaneously with glucose fermentation [saccharification and fermentation (SSF) process] using a strain of Saccharomyces cerevisiae. The acid pretreatment was evaluated using a central composite design for sulfuric acid concentration (1.0-4.0 v/v) and solid to liquid ratio (1:2-1:4, grams to milliliter) as independent variables. A maximum xylose concentration of 50 g/L was obtained in the hemicellulosic hydrolysate. The fermentation of hemicellulosic hydrolysate and the SSF process were performed in bioreactors and the final ethanol concentrations of 15.3 g/L and 28.7 g/L were obtained, respectively.

Management of Hazardous Waste and Contaminated Land

OpenAIRE

Hilary Sigman; Sarah Stafford

2010-01-01

Regulation of hazardous waste and cleanup of contaminated sites are two major components of modern public policy for environmental protection. We review the literature on these related areas, with emphasis on empirical analyses. Researchers have identified many behavioral responses to regulation of hazardous waste, including changes in the location of economic activity. However, the drivers behind compliance with these costly regulations remain a puzzle, as most research suggests a limited ro...

Bioassay-based risk assessment of hazardous waste

Energy Technology Data Exchange (ETDEWEB)

Donnelly, K.C.; Brown, K.W.; He, L.Y. [Texas A and M Univ., College Station, TX (United States)

1994-12-31

Microbial bioassays have been used to assess the genotoxic hazard at more than 30 different hazardous waste sites. Environmental samples were extracted with dichloromethane and methanol, and the resulting residue tested using GC/MS analysis as well as the Salmonella Microsomal and E. coli Prophage Induction assays. At a munitions wastewater contaminated site, there was no correlation between mutagenicity in bacteria, and the risk as estimated from chemical analysis data of trinitrotoluene. Samples 202 and 204 from a coal gasification site contained 72 mg/kg and 9 mg/kg benzo(a)pyrene, whereas the mutagenic responses of these samples were 231 net revertants/mg and 902 revertants/mg, respectively. The data suggest that microbial bioassays provide a valuable tool for monitoring the interactions of the components of a complex mixture.

The never ending burden: Germany in the year 1 past Chernobyl: Confused experts, distressed mothers, contaminated milk. Radiation doses went down, but the cancer risk and genetic hazards remain

International Nuclear Information System (INIS)

Brunner, E.; Janssen, K.H.

1986-01-01

Becquerel values in milk and meat are due to rise again during the next few weeks. The Federal Republic of Germany continues to live with the radioactive burden brought by the Chernobyl clouds. It is true that the radiation doses are lower than expected, but low-dose exposure, too, can have evil effects; the cancer risk and genetic hazards still remain incalculable. The article presents a survey of the radiation exposure in the country as a function of geographic data, and a rough assessment of possible consequences emanating from ingestion of contaminated food. (orig./GL) [de

Assessment of alternatives for long-term management of uranium ore residues and contaminated soils located at DOE's Niagara Falls Storage Site

International Nuclear Information System (INIS)

Merry-Libby, P.

1985-01-01

About 11,000 m 3 of uranium ore residues and 180,000 m 3 of slightly contaminated soils (wastes) are consolidated within a diked containment area at the Niagara Falls Storage Site located about 30 km north of Buffalo, New York. The residues account for less than 6% of the total volume of contaminated materials but almost 99% of the radioactivity. The average radium-226 concentration in the residues is 67,000 pCi/g. The US Department of Energy is considering several alternatives for long-term management of the wastes and residues, including: improvement of the containment at NFSS, modification of the form of the residues, management of the residues separately from the wastes, management of the wastes and residues at another humid site (Oak Ridge, Tennessee) or an arid site (Hanford, Washington), and dispersal of the wastes in the ocean. Potential radiological risks associated with implementation of any of the alternatives are expected to be smaller than the nonradiological risks of occupational and transportation-related injuries and deaths. Dispersal of the slightly contaminated wastes in the ocean is not expected to result in any significant radiological risk to humans. The residues and wastes will remain hazardous for thousands of years. After controls cease, the radioactive materials will eventually be dispersed in the environment. Loss of the earthen covers over the buried materials is predicted to occur from several hundred to more than two million years, depending primarily on the use of the land surface. Groundwater will eventually be contaminated in all alternatives; however, the groundwater pathway is relatively insignificant with respect to radiological risks to the general population. 2 references, 2 figures, 6 tables

Organic amendments for risk mitigation of organochlorine pesticide residues in old orchard soils

Science.gov (United States)

Centofantia, Tiziana; McConnell, Laura L.; Chaney, Rufus L.; Beyer, W. Nelson; Andradea, Natasha A.; Hapeman, Cathleen J.; Torrents, Alba; Nguyen, Anh; Anderson, Marya O.; Novak, J. M.; Jackson, Dana

2015-01-01

Performance of compost and biochar amendments for in situ risk mitigation of aged DDT, DDE and dieldrin residues in an old orchard soil was examined. The change in bioavailability of pesticide residues to Lumbricus terrestris L. relative to the unamended control soil was assessed using 4-L soil microcosms with and without plant cover in a 48-day experiment. The use of aged dairy manure compost and biosolids compost was found to be effective, especially in the planted treatments, at lowering the bioavailability factor (BAF) by 18–39%; however, BAF results for DDT in the unplanted soil treatments were unaffected or increased. The pine chip biochar utilized in this experiment was ineffective at lower the BAF of pesticides in the soil. The US EPA Soil Screening Level approach was used with our measured values. Addition of 10% of the aged dairy manure compost reduced the average hazard quotient values to below 1.0 for DDT + DDE and dieldrin. Results indicate this sustainable approach is appropriate to minimize risks to wildlife in areas of marginal organochlorine pesticide contamination. Application of this remediation approach has potential for use internationally in areas where historical pesticide contamination of soils remains a threat to wildlife populations.

Cyolane residues in milk of lactating goats

International Nuclear Information System (INIS)

Zayed, S.M.A.D.; Osman, A.; Fakhr, I.M.I.

1981-01-01

Consecutive feeding of lactating goats with 14 C-alkyl labelled cyolane for 5 days at dietary levels 8 and 16 ppm resulted in the appearance of measurable insecticide residues in milk (0.02-0.04 mg/kg). The residue levels were markedly reduced after a withdrawal period of 7 days. Analysis of urine and milk residues showed the presence of similar metabolites in addition to the parent compound. The major part of the residue consisted of mono-, diethyl phosphate and 2 hydrophilic unknown metabolites. The erythrocyte cholinesterase activity was reduced to about 50% after 24 hours whereas the plasma enzyme was only slightly affected. The animals remained symptom-free during the experimental period. (author)

Assessing insecticide hazard to bumble bees foraging on flowering weeds in treated lawns.

Directory of Open Access Journals (Sweden)

Jonathan L Larson

Full Text Available Maintaining bee-friendly habitats in cities and suburbs can help conserve the vital pollination services of declining bee populations. Despite label precautions not to apply them to blooming plants, neonicotinoids and other residual systemic insecticides may be applied for preventive control of lawn insect pests when spring-flowering weeds are present. Dietary exposure to neonicotinoids adversely affects bees, but the extent of hazard from field usage is controversial. We exposed colonies of the bumble bee Bombus impatiens to turf with blooming white clover that had been treated with clothianidin, a neonicotinoid, or with chlorantraniliprole, the first anthranilic diamide labeled for use on lawns. The sprays were applied at label rate and lightly irrigated. After residues had dried, colonies were confined to forage for six days, and then moved to a non-treated rural site to openly forage and develop. Colonies exposed to clothianidin-treated weedy turf had delayed weight gain and produced no new queens whereas those exposed to chlorantraniliprole-treated plots developed normally compared with controls. Neither bumble bees nor honey bees avoided foraging on treated white clover in open plots. Nectar from clover blooms directly contaminated by spray residues contained 171±44 ppb clothianidin. Notably, neither insecticide adversely impacted bee colonies confined on the treated turf after it had been mown to remove clover blooms present at the time of treatment, and new blooms had formed. Our results validate EPA label precautionary statements not to apply neonicotinoids to blooming nectar-producing plants if bees may visit the treatment area. Whatever systemic hazard through lawn weeds they may pose appears transitory, however, and direct hazard can be mitigated by adhering to label precautions, or if blooms inadvertently are contaminated, by mowing to remove them. Chlorantraniliprole usage on lawns appears non-hazardous to bumble bees.

Assessing Insecticide Hazard to Bumble Bees Foraging on Flowering Weeds in Treated Lawns

Science.gov (United States)

Larson, Jonathan L.; Redmond, Carl T.; Potter, Daniel A.

2013-01-01

Maintaining bee-friendly habitats in cities and suburbs can help conserve the vital pollination services of declining bee populations. Despite label precautions not to apply them to blooming plants, neonicotinoids and other residual systemic insecticides may be applied for preventive control of lawn insect pests when spring-flowering weeds are present. Dietary exposure to neonicotinoids adversely affects bees, but the extent of hazard from field usage is controversial. We exposed colonies of the bumble bee Bombus impatiens to turf with blooming white clover that had been treated with clothianidin, a neonicotinoid, or with chlorantraniliprole, the first anthranilic diamide labeled for use on lawns. The sprays were applied at label rate and lightly irrigated. After residues had dried, colonies were confined to forage for six days, and then moved to a non-treated rural site to openly forage and develop. Colonies exposed to clothianidin-treated weedy turf had delayed weight gain and produced no new queens whereas those exposed to chlorantraniliprole-treated plots developed normally compared with controls. Neither bumble bees nor honey bees avoided foraging on treated white clover in open plots. Nectar from clover blooms directly contaminated by spray residues contained 171±44 ppb clothianidin. Notably, neither insecticide adversely impacted bee colonies confined on the treated turf after it had been mown to remove clover blooms present at the time of treatment, and new blooms had formed. Our results validate EPA label precautionary statements not to apply neonicotinoids to blooming nectar-producing plants if bees may visit the treatment area. Whatever systemic hazard through lawn weeds they may pose appears transitory, however, and direct hazard can be mitigated by adhering to label precautions, or if blooms inadvertently are contaminated, by mowing to remove them. Chlorantraniliprole usage on lawns appears non-hazardous to bumble bees. PMID:23776667

Estimating Residual Solids Volume In Underground Storage Tanks

International Nuclear Information System (INIS)

Clark, Jason L.; Worthy, S. Jason; Martin, Bruce A.; Tihey, John R.

2014-01-01

The Savannah River Site liquid waste system consists of multiple facilities to safely receive and store legacy radioactive waste, treat, and permanently dispose waste. The large underground storage tanks and associated equipment, known as the 'tank farms', include a complex interconnected transfer system which includes underground transfer pipelines and ancillary equipment to direct the flow of waste. The waste in the tanks is present in three forms: supernatant, sludge, and salt. The supernatant is a multi-component aqueous mixture, while sludge is a gel-like substance which consists of insoluble solids and entrapped supernatant. The waste from these tanks is retrieved and treated as sludge or salt. The high level (radioactive) fraction of the waste is vitrified into a glass waste form, while the low-level waste is immobilized in a cementitious grout waste form called saltstone. Once the waste is retrieved and processed, the tanks are closed via removing the bulk of the waste, chemical cleaning, heel removal, stabilizing remaining residuals with tailored grout formulations and severing/sealing external penetrations. The comprehensive liquid waste disposition system, currently managed by Savannah River Remediation, consists of 1) safe storage and retrieval of the waste as it is prepared for permanent disposition; (2) definition of the waste processing techniques utilized to separate the high-level waste fraction/low-level waste fraction; (3) disposition of LLW in saltstone; (4) disposition of the HLW in glass; and (5) closure state of the facilities, including tanks. This paper focuses on determining the effectiveness of waste removal campaigns through monitoring the volume of residual solids in the waste tanks. Volume estimates of the residual solids are performed by creating a map of the residual solids on the waste tank bottom using video and still digital images. The map is then used to calculate the volume of solids remaining in the waste tank. The ability to

Food contamination with environmentally hazardous chemical substances. Kontamination von Lebensmitteln mit Umweltchemikalien

Energy Technology Data Exchange (ETDEWEB)

Petz, M [Wuppertal Univ. (Gesamthochschule) (Germany, F.R.). Fachbereich 9 - Naturwissenschaften 2 - Chemie - Biologie

1990-01-01

The author explains the difference between residues and contaminants in food. Of the contaminants, the heavy metals lead, cadmium and mercury are discussed at length, e.g. their pathway through the food chain and their accumulation in plants, animals, and humans etc. PCB in food and in mother's milk are gone into, as are the consequences of this contamination. Finally, dibenzofuranes and dibenzodioxins are mentioned, again with a view to the contamination of mother's milk. The health hazards from contaminated food is related to the health hazards of malnutrition and overeating. (MG).

Implementing DOE guidance for hazards assessments at Rocky Flats Plant

International Nuclear Information System (INIS)

Zimmerman, G.A.

1993-01-01

Hazards Assessments are performed for a variety of activities and facilities at Rocky Flats Plant. Prior to 1991, there was no guidance for performing Hazards Assessments. Each organization that performed Hazards Assessments used its own methodology with no attempt at standardization. In 1991, DOE published guidelines for the performance of Hazards Assessments for Emergency Planning (DOE-EPG-5500.1, ''Guidance for a Hazards Assessment Methodology''). Subsequently, in 1992, DOE published a standard for the performance of Hazards Assessments (DOE-STD-1027-92, ''Hazard Categorization and Accident Analysis, Techniques for Compliance with DOE Order 5480.23, Nuclear Safety Analysis Reports''). Although these documents are a step in the direction of standardization, there remains a great deal of interpretation and subjective implementation in the performance of Hazards Assessments. Rocky Flats Plant has initiated efforts to develop a uniform and standard process to be used for Hazards Assessments

Comprehensive characterization and hazard assessment of the DOE-Niagara Falls storage site

International Nuclear Information System (INIS)

Anderson, T.L.; Dettorre, J.F.; Jackson, D.R.; Ausmus, B.S.

1981-06-01

A comprehensive radioecological and nonradiological characterization and hazards assessment was conducted on DOE-Niagara Falls Storage Site. Pitchblende residues and other low-level nuclear waste have been stored on the site since 1944. The most highly radioactive residues were stored in four abandoned buildings, while other wastes were deposited in pits or piled on surface soils on the Site. Several ditches were constructed on the Site to facilitate drainage or excess precipitation. Results of the study will permit the US DOE to form an appropriate remedial action plan for the Site

Drug and chemical residues in domestic animals.

Science.gov (United States)

Mussman, H C

1975-02-01

Given the large number of chemical substances that may find their way into the food supply, a system is needed to monitor their presence. The U. S. Department of Agriculture's Meat and Poultry Inspection Program routinely tests for chemical residues in animals coming to slaughter. Pesticides, heavy metals, growth promotants (hormones and hormonelike agents), and antibiotics are included. Samples are taken statistically so that inferences as to national incidence of residues can be drawn. When a problem is identified, a more selective sampling is designed to help follow up on the initial regulatory action. In testing for pesticides, only DDT and dieldrin are found with any frequency and their levels are decreasing; violative residues of any chlorinated hydrocarbon are generally a result of an industrial accident rather than agricultural usage. Analyses for heavy metals have revealed detectable levels of mercury, lead, and others, but none at levels that are considered a health hazard. Of the hormone or hormonelike substances, only diethylstilbestrol has been a residue problem and its future is uncertain. The most extensive monitoring for veterinary drugs is on the antimicrobials, including sulfonamides, streptomycin, and the tetracycline group of antibiotics that constitute the bulk of the violations; their simultaneous use prophylactically and therapeutically has contributed to the problem in certain cases. A strong, well-designed user education program on proper application of pesticides, chemicals, and veterinary drugs appears to be one method of reducing the incidence of unwanted residues.

Contribution of microorganisms to non-extractable residue formation during biodegradation of ibuprofen in soil.

Science.gov (United States)

Nowak, Karolina M; Girardi, Cristobal; Miltner, Anja; Gehre, Matthias; Schäffer, Andreas; Kästner, Matthias

2013-02-15

Non-extractable residues (NER) formed during biodegradation of organic contaminants in soil are considered to be mainly composed of parent compounds or their primary metabolites with hazardous potential. However, in the case of biodegradable organic compounds, the soil NER may also contain microbial biomass components, for example fatty acids (FA) and amino acids (AA). After cell death, these biomolecules are subsequently incorporated into non-living soil organic matter (SOM) and are stabilised ultimately forming hardly extractable residues of biogenic origin. We investigated biodegradation of (13)C(6)-ibuprofen, in particular the metabolic incorporation of the (13)C-label into FA and AA and their fate in soil over 90 days. (13)C-FA and (13)C-AA amounts in the living microbial biomass fraction initially increased, then decreased over time and were continuously incorporated into the non-living SOM pool. The (13)C-FA in the non-living SOM remained stable from day 59 whereas the contents of (13)C-AA slightly increased until the end. After 90 days, nearly all NER were biogenic as they were made up almost completely by natural biomass compounds. The presented data demonstrated that the potential environmental risks related to the ibuprofen-derived NER are overestimated. Copyright © 2012 Elsevier B.V. All rights reserved.

EFSA BIOHAZ Panel (EFSA Panel on Biological Hazards, 2013. Scientific Opinion on the public health hazards to be covered by inspection of meat from sheep and goats

DEFF Research Database (Denmark)

Hald, Tine; Baggesen, Dorte Lau

A risk ranking process identified Toxoplasma gondii and pathogenic verocytotoxin-producing Escherichia coli (VTEC) as the most relevant biological hazards for meat inspection of sheep and goats. As these are not detected by traditional meat inspection, a meat safety assurance system using risk......-based interventions was proposed. Further studies are required on T. gondii and pathogenic VTEC. If new information confirms these hazards as a high risk to public health from meat from sheep or goats, setting targets at carcass level should be considered. Other elements of the system are risk...... the extensive production systems used, and the ranking of chemical substances, which should be regularly updated and include new hazards. Control programmes across the food chain, national residue control plans, feed control and monitoring of environmental contaminants should be better integrated. Meat...

Mineral remains of early life on Earth? On Mars?

Science.gov (United States)

Iberall, Robbins E.; Iberall, A.S.

1991-01-01

The oldest sedimentary rocks on Earth, the 3.8-Ga Isua Iron-Formation in southwestern Greenland, are metamorphosed past the point where organic-walled fossils would remain. Acid residues and thin sections of these rocks reveal ferric microstructures that have filamentous, hollow rod, and spherical shapes not characteristic of crystalline minerals. Instead, they resemble ferric-coated remains of bacteria. Because there are no earlier sedimentary rocks to study on Earth, it may be necessary to expand the search elsewhere in the solar system for clues to any biotic precursors or other types of early life. A study of morphologies of iron oxide minerals collected in the southern highlands during a Mars sample return mission may therefore help to fill in important gaps in the history of Earth's earliest biosphere. -from Authors

Atherogenic Dyslipidemia and Residual Cardiovascular Risk in Statin-Treated Patients

DEFF Research Database (Denmark)

Sirimarco, Gaia; Labreuche, Julien; Bruckert, Eric

2014-01-01

BACKGROUND AND PURPOSE: Treatment with statins reduces the rate of cardiovascular events in high-risk patients, but residual risk persists. At least part of that risk may be attributable to atherogenic dyslipidemia characterized by low high-density lipoprotein cholesterol (≤40 mg/dL) and high......% of subjects in PERFORM and 9% in SPARCL had atherogenic dyslipidemia after ≥3 months on start statin therapy. After a follow-up of 2.3 years (PERFORM) and 4.9 years (SPARCL), a major cardiovascular event occurred in 1123 and 485 patients in the 2 trials, respectively. The risk of major cardiovascular events...... was higher in subjects with versus those without atherogenic dyslipidemia in both PERFORM (hazard ratio, 1.36; 95% confidence interval, 1.14-1.63) and SPARCL (hazard ratio, 1.40; 95% confidence interval, 1.06-1.85). The association was attenuated after multivariable adjustment (hazard ratio, 1.23; 95...

The transport of hazardous materials

International Nuclear Information System (INIS)

Goemmel, F.

1987-01-01

The rapid development of all kinds of transports has been leading to a continuously increasing number of accidents involving the release and escape of hazardous materials. The risks involved for men and the environment have to be realized and reduced to a minimum. Efforts in this field have meanwhile been accumulating an enormous quantity of rules, recommendations and regulations. They comprise, among others, both national and international rail transport, maritime transport, inland shipping, air and road transport regulations adding up to a total of about 5000 pages. The publication discusses the necessity and justification of the existing quantity of regulations, it deals with their possible simplification and modified user-oriented arrangement as well as with a possible international harmonization of regulations. Apart from giving a general survey of the transport of hazardous materials the author reviews the intensive efforts which are going into the safety of the transport of hazardous materials and points out technical and legal problems which have remained unsolved so far. The publication essentially contributes to clearing up the background, perspectives and prospects of the complex regulations controlling the transport of hazardous materials. (orig./HP) [de

Electricity remains a serious workplace hazard.

Science.gov (United States)

Proctor, Laura; Kuchibotla, Srin

2013-08-01

Anyone who works in an industrial environment or is employed in the utility, mass transit, industrial goods manufacturing, or telecommunications industry - as well as many others - may be at risk for electrocution. Electric shock costs workers' lives and results in painful and debilitating injuries every year. Lockout/tagout procedures protect against electrocution, as do rubber insulating gloves, which must be worn any time workers are exposed to energized parts operating at 50 volts or higher. Some newer styles of rubber insulating gloves not only protect against electric shock, but also offer the dexterity and flexibility workers need for hours of comfortable wear.

Food contamination with environmentally hazardous chemical substances. Kontamination von Lebensmitteln mit Umweltchemikalien

Energy Technology Data Exchange (ETDEWEB)

Petz, M. (Wuppertal Univ. (Gesamthochschule) (Germany, F.R.). Fachbereich 9 - Naturwissenschaften 2 - Chemie - Biologie)

1990-01-01

The author explains the difference between residues and contaminants in food. Of the contaminants, the heavy metals lead, cadmium and mercury are discussed at length, e.g. their pathway through the food chain and their accumulation in plants, animals, and humans etc. PCB in food and in mother's milk are gone into, as are the consequences of this contamination. Finally, dibenzofuranes and dibenzodioxins are mentioned, again with a view to the contamination of mother's milk. The health hazards from contaminated food is related to the health hazards of malnutrition and overeating. (MG).

Remaining Sites Verification Package for the 126-B-2, 183-B Clearwells

International Nuclear Information System (INIS)

Dittmer, L.M.

2007-01-01

The 126-B-2, 183-B Clearwells were built as part of the 183-B Water Treatment Facility and are composed of 2 covered concrete reservoirs. The bulk of the water stored in the clearwells was used as process water to cool the 105-B Reactor and as a source of potable water. Residual conditions were determined to meet the remedial action objectives specified in the Remaining Sites ROD through an evaluation of the available process knowledge. The results of the evaluation do not preclude any future uses and allow for unrestricted use of shallow zone soils. The results also indicate that residual concentrations are protective of groundwater and the Columbia River.

Methyl bromide residues in fumigated cocoa beans with particular reference to inorganic bromide

International Nuclear Information System (INIS)

Adomako, D.

1976-01-01

Inorganic bromide residues and 14 C-labelled methylated products (expressed as CH 3 Br equivalent) in cocoa beans fumigated with [ 14 C]-methyl bromide have been determined by radiometric and chemical methods. Determination of 14 C by direct combustion in an oxygen chamber followed by liquid scintillation counting confirmed previous findings with respect to the magnitude, distribution and chemical nature of the residues. Although recovery of added bromide was good, the values of total bromide obtained by the chemical method were only half of those estimated from the total residual 14 C-activity. This is attributed to loss of organic (presumably, protein-bound) bromide. In agreement with the total 14 C-labelled residue contents, total bromide in shells was 20 times greater than that in nibs. The low levels of residues in the nib (12ppm as CH 3 Br equivalent, 10ppm Br) and the further reduction of organic residues by roasting suggest that no toxicological and nutritional hazards may be expected from fumigation of cocoa beans with methyl bromide. (author)

Estimation of average causal effect using the restricted mean residual lifetime as effect measure

DEFF Research Database (Denmark)

Mansourvar, Zahra; Martinussen, Torben

2017-01-01

with respect to their survival times. In observational studies where the factor of interest is not randomized, covariate adjustment is needed to take into account imbalances in confounding factors. In this article, we develop an estimator for the average causal treatment difference using the restricted mean...... residual lifetime as target parameter. We account for confounding factors using the Aalen additive hazards model. Large sample property of the proposed estimator is established and simulation studies are conducted in order to assess small sample performance of the resulting estimator. The method is also......Although mean residual lifetime is often of interest in biomedical studies, restricted mean residual lifetime must be considered in order to accommodate censoring. Differences in the restricted mean residual lifetime can be used as an appropriate quantity for comparing different treatment groups...

Residues of 14C-paclobutrazol in mangoes

International Nuclear Information System (INIS)

Costa, Maria A.; Tornisielo, Valdemar L.; Castanho, Giuliane M.

2009-01-01

Paclobutrazol (PBZ) is a growth regulator used in agricultural systems whose purpose is the control of vegetative growth, stimulating the reproductive capacity of plants. This growth regulator remains active in soil for a long time and its half-life varies with the type of soil and climatic conditions, can severely affect the development of crops. This work aimed to study the residues / metabolites of 14 C-PBZ in mango pulp Tommy Atkins. The tests were performed with mangoes grown in pots stainless steel and application of 14 C-PBZ was performed by the soil projection of the crown, and the mangoes tested in two periods, one year and two years after application. To evaluate the levels of residues of 14 C-PBZ was realize the burning of 200 mg of pulp on biological oxidized and detached 14 CO 2 was detected by liquid scintillation spectrophotometer. The results were 1.65 % of residue of PBZ on fruit collected after two years of application and 4.30 % of residue of PBZ collected on fruit after a year of application and also can see that the product remained in the soil for more than one year, is translocated to the plant and reach the edible part, the pulp fruit. The identification of residual 14 C- PBZ/metabolites by thin-layer chromatography did not reveal any pattern of PBZ / metabolites due to the low activity detected in the samples. Therefore, another procedure was performed for extraction and then analyzed by high performance liquid chromatography (HPLC) for detection of metabolites in the PBZ of mango pulp. (author)

Double-pulse standoff laser-induced breakdown spectroscopy for versatile hazardous materials detection

Energy Technology Data Exchange (ETDEWEB)

Gottfried, Jennifer L. [U.S. Army Research Laboratory, AMSRD-ARL-WM-BD, Aberdeen Proving Ground, MD, 21005-5069 (United States)], E-mail: jennifer.gottfried@arl.army.mil; De Lucia, Frank C.; Munson, Chase A.; Miziolek, Andrzej W. [U.S. Army Research Laboratory, AMSRD-ARL-WM-BD, Aberdeen Proving Ground, MD, 21005-5069 (United States)

2007-12-15

We have developed a double-pulse standoff laser-induced breakdown spectroscopy (ST-LIBS) system capable of detecting a variety of hazardous materials at tens of meters. The use of a double-pulse laser improves the sensitivity and selectivity of ST-LIBS, especially for the detection of energetic materials. In addition to various metallic and plastic materials, the system has been used to detect bulk explosives RDX and Composition-B, explosive residues, biological species such as the anthrax surrogate Bacillus subtilis, and chemical warfare simulants at 20 m. We have also demonstrated the discrimination of explosive residues from various interferents on an aluminum substrate.

Chloroxyanion residues in cantaloupe and tomatoes after chlorine dioxide gas sanitation

Science.gov (United States)

Chlorine dioxide gas is effective at cleansing fruits and vegetables of bacterial pathogens and(or) rot organisms, but few data are available on chemical residues remaining subsequent to chlorine gas treatment. Therefore, studies were conducted to quantify chlorate and perchlorate residues after tom...

Laboratory studies of the properties of in-situ burn residues: chemical composition of residues

International Nuclear Information System (INIS)

Trudel, B.K.; Buist, I.A.; Schatzke, D.; Aurand, D.

1996-01-01

The chemical composition of the residue from small-scale burns of thick oil slicks was studied. The objective was to describe the changes in chemical composition in oils burning on water and to determine how these changes were influenced by the condition of the burn. Small-scale test burns involved burning 40-cm diameter pools of oil on water. A range of eight oil types including seven crude oils and an automotive diesel were burned. For each oil, slicks of fresh oil of three different thicknesses were tested. Two of the oils were tested before and after weathering. Results showed that the composition of the residue differed greatly from the parent oil. Asphaltenes, high-boiling-point aromatics and resins remained concentrated in the burn residue. The burning of slicks appeared to remove most of the lower-molecular weight aromatic hydrocarbons which included the more toxic and more bioavailable components of the crude oils. 11 refs., 6 tabs

Baltic Sea hazardous substances management: results and challenges.

Science.gov (United States)

Selin, Henrik; VanDeveer, Stacy D

2004-05-01

The introduction into the Baltic Sea of hazardous substances that are persistent, bioaccumulate, and are toxic is an important environmental and human health problem. Multilateral efforts to address this problem have primarily been taken under the Helsinki Commission (HELCOM). This article examines past HELCOM efforts on hazardous substances, and discusses future challenges regarding their management. The article finds that past actions on hazardous substances have had a positive effect on improving Baltic environmental quality and reducing human health risks, although there are remaining issues and difficulties that need to be addressed. In particular, four related future challenges for HELCOM management of hazardous substances are identified and discussed: i) the need to engender further implementation and building public and private sector capacities; ii) the need to improve data availability, quality and comparability across the region and international fora; iii) the need to strengthen existing regulations and incorporate new issues; and iv) the need to effectively coordinate HELCOM activities with efforts on hazardous substances in other international fora.

14 CFR 417.415 - Post-launch and post-flight-attempt hazard controls.

Science.gov (United States)

2010-01-01

...-flight-attempt hazard controls. (a) A launch operator must establish, maintain and perform procedures for... system operation. The flight termination system receivers must remain captured by the command control... launch operator must establish procedural controls for hazards associated with an unsuccessful flight...

Management of solid residues in waste-to-energy and biomass systems

Energy Technology Data Exchange (ETDEWEB)

Vehlow, J.; Bergfeldt, B. [Forschungszentrum Karlsruhe GmbH Technik und Umwelt (Germany). Inst. fuer Technische Chemie; Wilen, C.; Ranta, J. [VTT Technical Research Centre of Finland, Espoo (Finland); Schwaiger, H. [Forschungsgesellschaft Joanneum mbH, Graz (Austria); Visser, H.J.M. [ECN Energy Research Centre of the Netherlands, Petten (Netherlands); Gu, S.; Gyftopoulou, E.; Brammer, J. [Aston Univ., Birmingham (United Kingdom)

2007-12-15

A literature review has been performed for getting in-depth information about quality of residues from thermal processes for waste and biomass as well as their disposal or utilisation options and current practices. Residues from waste incineration have been subject to intense research programs for many years and it can be concluded that the quality of bottom ashes has meanwhile a high standard. The question whether an utilisation as secondary building material is accepted or not depends on the definition of acceptable economic impac. For filter ashes and gas cleaning residues the situation is more complex. Their quality is known: due to their high inventory of heavy metals and organic micro-pollutants they are classified as hazardous waste which means they require specific measures for their safe long-term disposal. A number of stabilisation and treatment processes for filter ashes and gas cleaning residues including the recovery of species out of these materials have been developed but none has been implemented in full scale due to economic constraints. There is reason to speculate that even recovery processes which are not profitable for private companies might point out economically useful if future and long-term costs which have to be covered of the society, e.g. for rehabilitation of contaminated sites, are taken into account. Their quality as well as that of residues from combustion of contaminated biomass is mainly depending on the quality of the fuel. The inventory of critical ingredients in fuel produced from waste or waste fractions, especially of halogens and heavy metals, is often rather high and shows typically a wide range of variation. A reliable quality control for such fuels is very difficult. Other residues can - like gas cleaning residues from waste incineration - be inertised in order to meet the criteria for the access to cheaper landfills than those for hazardous waste. A similar conclusion can be drawn for the quality and management of

Checking Fine and Gray subdistribution hazards model with cumulative sums of residuals

DEFF Research Database (Denmark)

Li, Jianing; Scheike, Thomas; Zhang, Mei Jie

2015-01-01

Recently, Fine and Gray (J Am Stat Assoc 94:496–509, 1999) proposed a semi-parametric proportional regression model for the subdistribution hazard function which has been used extensively for analyzing competing risks data. However, failure of model adequacy could lead to severe bias in parameter...... estimation, and only a limited contribution has been made to check the model assumptions. In this paper, we present a class of analytical methods and graphical approaches for checking the assumptions of Fine and Gray’s model. The proposed goodness-of-fit test procedures are based on the cumulative sums...

Can hazard risk be communicated through a virtual experience?

Science.gov (United States)

Mitchell, J T

1997-09-01

Cyberspace, defined by William Gibson as a consensual hallucination, now refers to all computer-generated interactive environments. Virtual reality, one of a class of interactive cyberspaces, allows us to create and interact directly with objects not available in the everyday world. Despite successes in the entertainment and aviation industries, this technology has been called a 'solution in search of a problem'. The purpose of this commentary is to suggest such a problem: the inability to acquire experience with a hazard to motivate mitigation. Direct experience with a hazard has been demonstrated as a powerful incentive to adopt mitigation measures. While we lack the ability to summon hazard events at will in order to gain access to that experience, a virtual environment can provide an arena where potential victims are exposed to a hazard's effects. Immersion as an active participant within the hazard event through virtual reality may stimulate users to undertake mitigation steps that might otherwise remain undone. This paper details the possible direction in which virtual reality may be applied to hazards mitigation through a discussion of the technology, the role of hazard experience, the creation of a hazard stimulation and the issues constraining implementation.

Coalbed methane: from hazard to resource

Science.gov (United States)

Flores, R.M.

1998-01-01

Coalbed gas, which mainly consists of methane, has remained a major hazard affecting safety and productivity in underground coal mines for more than 100 yr. Coalbed gas emissions have resulted in outbursts and explosions where ignited by open lights, smoking or improper use of black blasting powder, and machinery operations. Investigations of coal gas outbursts and explosions during the past century were aimed at predicting and preventing this mine hazard. During this time, gas emissions were diluted with ventilation by airways (eg, tunnels, vertical and horizontal drillholes, shsfts) and by drainage boreholes. The 1970s 'energy crisis' led to studies of the feasibility of producing the gas for commercial use. Subsequent research on the origin, accumulation, distribution, availability, and recoverability has been pursued vigorously during the past two decades. Since the 1970s research investigations on the causes and effects of coal mine outbursts and gas emissions have led to major advances towards the recovery and development of coalbed methane for commercial use. Thus, coalbed methane as a mining hazard was harnessed as a conventional gas resource.Coalbed gas, which mainly consists of methane, has remained a major hazard affecting safety and productivity in underground coal mines for more than 100 years. Coalbed gas emissions have resulted in outbursts and explosions where ignited by open lights, smoking or improper use of black blasting powder, and machinery operations. Investigations of coal gas outbursts and explosions during the past century were aimed at predicting and preventing this mine hazard. During this time, gas emissions were diluted with ventilation by airways (e.g., tunnels, vertical and horizontal drillholes, shafts) and by drainage boreholes. The 1970's `energy crisis' led to studies of the feasibility of producing the gas for commercial use. Subsequent research on the origin, accumulation, distribution, availability, and recoverability has been

Progress in stabilization of plutonium and residues since DNFSB recommendation 94-1

International Nuclear Information System (INIS)

Ball, J.M.; Dustin, D.F.

1998-01-01

There are approximately 100 metric tons of residues at the Rocky Flats Environmental Technology Site containing approximately 3 metric tons of plutonium. The residues are byproducts of past plutonium operations incinerator ash; pyrochemical salts; graphite; sand, slag, and crucible; and miscellaneous forms of combustibles, glass, metal, and sludges. In September 1993, a report was released (Reference 1) which identified concerns with the chemical stability of the residues and with the integrity of packaging. In May 1997, the Defense Nuclear Facility Safety Board published recommendation 94-1 citing a concern for the residue stability and requiring that the possibly unstable residues be processed within 3 years and all others within 5 years. A risk categorization scheme was developed which assigned a numerical risk to each residue type based on the probability and consequence of occurrence of failures associated with the hazards identified. The residues were ranked for priority of stabilization actions. Urgent concerns were resolved. All residue drums were vented to eliminate the potential for hydrogen and other explosive gas accumulation. Leaded rubber gloves and ion exchange resins were washed to eliminate the explosion potential. An aggressive characterization program was implemented to search for any additional safety or environmental concerns and to gain more definitive information concerning the choice of processes for stabilization and disposition of the residues. This paper provides background on the safety issues and summarizes recent characterization data. The residue processing and disposition plans, including schedule and cost, are also summarized in the paper. Finally, the paper addresses initiatives undertaken by Safe Sites of Colorado to accelerate the residue program

Contracting in the wine supply chain with bilateral moral hazard, residual claimancy and multitasking

DEFF Research Database (Denmark)

Steiner, Bodo

2012-01-01

This paper takes a quasi-case-study approach to stylised wine industry facts to assess predictions about the optimal sharing rule from a principal–agent model with residual claimancy. An optimal sharing contract is developed between a grape grower and a winery, when a risk-averse grower allocates...

Fermentative utilization of glycerol residue for the production of acetic acid

Science.gov (United States)

Irvan; Trisakti, B.; Hasibuan, R.; Joli, M.

2018-02-01

Glycerol residue, frequently known as pitch, is a waste produced from the downstream product of crude glycerine distillation. With the increasing need of pure glycerine in the world, the glycerol residue produced is also increasing. Glycerol residue is a solid waste at room temperature, highly alkaline (pH > 13), corrosive, and categorized as hazardous and poisonous waste. In this research, acetic acid was produced from glycerol residue through the anaerobic fermentation process by using purple non-sulphur photosynthetic bacteria. The purpose of this study was to find out the influence of concentration change of glycerol residue on time and to find out the possibility of glycerol residue to be utilized as acetic acid. In this research, at first 400 g of glycerol residue was diluted with 200 ml of distilled water to change the glycerine phase, from solid to liquid at room temperature, acidified by using hydrochloric acid until pH 2. The top layer formed was fatty acid and triglycerides that should be removed. Meanwhile, the bottom layer was diluted glycerol residue which was then neutralized with caustic soda. To produce acetic acid, glycerol residue with various concentrations, salt, and purple non-sulphur photosynthetic bacteria were put together into a 100 ml bottle which had been previously sterilized, then incubated for four weeks under the light of 40-watt bulb. The result showed that on the 28th day of fermentation, the produced acetic acid were 0.28, 1.85, and 0.2% (w/w) by using glycerine with the concentration of 0.5, 1.0, and 1.5% (w/w), respectively.

A Study of Residual Image in Charged-Coupled Device

Directory of Open Access Journals (Sweden)

Ho Jin

2005-12-01

Full Text Available For an image sensor CCD, electrons can be trapped at the front-side Si-SiO_2 surface interface in a case of exceeding the full well by bright source. Residual images can be made by the electrons remaining in the interface. These residual images are seen in the front-side-illuminated CCDs especially. It is not easy to find a quantitative analysis for this phenomenon in the domestic reports, although it is able to contaminate observation data. In this study, we find residual images in dark frames which were obtained from the front-side-illuminated CCD at Mt. Lemmon Optical Astronomy Observatory (LOAO, and analyze the effect to contaminated observation data by residual charges.

Low-residue euthanasia of stranded mysticetes.

Science.gov (United States)

Harms, Craig A; McLellan, William A; Moore, Michael J; Barco, Susan G; Clarke, Elsburgh O; Thayer, Victoria G; Rowles, Teresa K

2014-01-01

Euthanasia of stranded large whales poses logistic, safety, pharmaceutical, delivery, public relations, and disposal challenges. Reasonable arguments may be made for allowing a stranded whale to expire naturally. However, slow cardiovascular collapse from gravitational effects outside of neutral buoyancy, often combined with severely debilitating conditions, motivate humane efforts to end the animal's suffering. The size of the animal and prevailing environmental conditions often pose safety concerns for stranding personnel, which take priority over other considerations. When considering chemical euthanasia, the size of the animal also necessitates large quantities of euthanasia agents. Drug residues are a concern for relay toxicity to scavengers, particularly for pentobarbital-containing euthanasia solutions. Pentobarbital is also an environmental concern because of its stability and long persistence in aquatic environments. We describe a euthanasia technique for stranded mysticetes using readily available, relatively inexpensive, preanesthetic and anesthetic drugs (midazolam, acepromazine, xylazine) followed by saturated KCl delivered via custom-made needles and a low-cost, basic, pressurized canister. This method provides effective euthanasia while moderating personnel exposure to hazardous situations and minimizing drug residues of concern for relay toxicity.

Occupational hazards to dental staff

Directory of Open Access Journals (Sweden)

Jamshid Ayatollahi

2012-01-01

Full Text Available Dental professionals are predisposed to a number of occupational hazards. These include exposure to infections (including Human Immunodeficiency Virus and viral hepatitis; percutaneous exposure incidents, dental materials, radiation, and noise; musculoskeletal disorders; psychological problems and dermatitis; respiratory disorders; and eye insults. Percutaneous exposure incidents remain a main concern, as exposure to serious infectious agents is a virtual risk. Minimizing percutaneous exposure incidents and their consequences should continue to be considered, including sound infection control practices, continuing education, and hepatitis B vaccination. Basically, for any infection control strategies, dentists should be aware of individual protective measures and appropriate sterilization or other high-level disinfection utilities. Strained posture at work disturbs the musculoskeletal alignment and leads to stooped spine. The stooped posture also involved certain groups of muscles and joints. This may lead to diseases of the musculoskeletal system. Continuous educating and appropriate intervention studies are needed to reduce the complication of these hazards. So, it is important for dentists to remain constantly up-to-date about measures on how to deal with newer strategies and dental materials, and implicates the need for special medical care for this professional group.

Electrodialytic upgrading of MSWI APC residue from hazardous waste to secondary resource

DEFF Research Database (Denmark)

Jensen, Pernille Erland; Kirkelund, Gunvor Marie; Parés Viader, Raimon

.g. for substitution of cement or fillers in concrete. In general leaching could not be reduced by optimizing current density and treatment time in the pilot scale stack treatment unit, as hypothesized, even though there was evidence of dependency on current density for e.g. zinc, this was not true for most elements......The aim of this project was to contribute to the development of electrodialytic treatment technology of air pollution control residues (APC) from municipal solid waste incineration (MSWI) to obtain maximal leaching reduction by optimization of treatment time and current density for different types...

A centralized hazardous waste treatment plant: the facilities of the ZVSMM at Schwabach as an example

Energy Technology Data Exchange (ETDEWEB)

Amsoneit, Norbert [Zweckverband Sondermuell-Entsorgung Mittelfranken, Rednitzhembach (Germany)

1994-12-31

In this work a centralized hazardous waste treatment plant is described and its infra-structure is presented. Special emphasis is given to the handling of the residues produced and the different treatment processes at the final disposal. 2 refs., 4 figs.

A centralized hazardous waste treatment plant: the facilities of the ZVSMM at Schwabach as an example

Energy Technology Data Exchange (ETDEWEB)

Amsoneit, Norbert [Zweckverband Sondermuell-Entsorgung Mittelfranken, Rednitzhembach (Germany)

1993-12-31

In this work a centralized hazardous waste treatment plant is described and its infra-structure is presented. Special emphasis is given to the handling of the residues produced and the different treatment processes at the final disposal. 2 refs., 4 figs.

A proposal for a test method for assessment of hazard property HP 12 ("Release of an acute toxic gas") in hazardous waste classification - Experience from 49 waste.

Science.gov (United States)

Hennebert, Pierre; Samaali, Ismahen; Molina, Pauline

2016-12-01

A stepwise method for assessment of the HP 12 is proposed and tested with 49 waste samples. The hazard property HP 12 is defined as "Release of an acute toxic gas": waste which releases acute toxic gases (Acute Tox. 1, 2 or 3) in contact with water or an acid. When a waste contains a substance assigned to one of the following supplemental hazards EUH029, EUH031 and EUH032, it shall be classified as hazardous by HP 12 according to test methods or guidelines (EC, 2014a, 2014b). When the substances with the cited hazard statement codes react with water or an acid, they can release HCl, Cl 2 , HF, HCN, PH 3 , H 2 S, SO 2 (and two other gases very unlikely to be emitted, hydrazoic acid HN 3 and selenium oxide SeO 2 - a solid with low vapor pressure). Hence, a method is proposed:For a set of 49 waste, water addition did not produce gas. Nearly all the solid waste produced a gas in contact with hydrochloric acid in 5 min in an automated calcimeter with a volume >0.1L of gas per kg of waste. Since a plateau of pressure is reached only for half of the samples in 5 min, 6 h trial with calorimetric bombs or glass flasks were done and confirmed the results. Identification of the gases by portable probes showed that most of the tested samples emit mainly CO 2 . Toxic gases are emitted by four waste: metallic dust from the aluminum industry (CO), two air pollution control residue of industrial waste incinerator (H 2 S) and a halogenated solvent (organic volatile(s) compound(s)). HF has not been measured in these trials started before the present definition of HP 12. According to the definition of HP 12, only the H 2 S emission of substances with hazard statement EUH031 is accounted for. In view of the calcium content of the two air pollution control residue, the presence of calcium sulphide (EUH031) can be assumed. These two waste are therefore classified potentially hazardous for HP 12, from a total of 49 waste. They are also classified as hazardous for other properties (HP 7

Risk assessment for children exposed to DDT residues in various milk types from the Greek market.

Science.gov (United States)

Tsakiris, Ioannis N; Goumenou, Marina; Tzatzarakis, Manolis N; Alegakis, Athanasios K; Tsitsimpikou, Christina; Ozcagli, Eren; Vynias, Dionysios; Tsatsakis, Aristidis M

2015-01-01

The occurrence of residues of DDT and its metabolites was monitored in 196 cow milk samples of various pasteurized commercial types collected from the Greek market. Residue levels were determined by GC-MS analysis. In 97.4% of the samples at least one DDT isomer or one of the DDT metabolites was detected, in levels not exceeding the maximum permitted residue level by the EU. Hazard Index for both carcinogenic and non-carcinogenic effects was estimated under two assumptions: a) using DDT concentrations from positive samples and b) imputing LOD/2 as an arbitrary concentration for negative samples. No statistically significant differences in detected or summed residue (p > 0.05) concentrations between different milk types were observed, with the exception of specific metabolites of DDT in some milk types. Exposure assessment scenarios were developed for children aged 1, 3, 5, 7 and 12 years old based on estimated body weights and daily milk consumption. Hazard Indices for non-carcinogenic effects were below 0.109 covering also carcinogenic effects according to WHO approach. The cancer risk values for carcinogenic effects according to the US EPA Cancer Benchmark Concentration approach, ranged from 0.4 to 18. For both effects the highest values were calculated for the 1- to 3-year-old age groups. Copyright © 2014 Elsevier Ltd. All rights reserved.

Availability of residual nitrogen from fertilizers in soil

International Nuclear Information System (INIS)

Jakovljevic, M.; Filipovic, R.; Petrovic, M.

1983-01-01

The plant availability of residual fertilizer nitrogen for the next crop was studied in chernozem and pseudogley soils. Release of nitrogen was examined after incubation at 3 and 30 0 C. It was found that the use of increased doses of nitrogen fertilizer (ammonium nitrate) led to an increased release of residual fertilizer nitrogen into plant available forms. The release of this nitrogen fraction was 5-10 times faster in comparison with the remaining soil nitrogen. (author)

Availability of residual nitrogen from fertilizers in soil

Energy Technology Data Exchange (ETDEWEB)

Jakovljevic, M.; Filipovic, R.; Petrovic, M. (Institut za Primeni Nuklearne Energije u Poljoprivedri, Veterinarstvu i Sumarstvu, Zemun (Yugoslavia))

1983-05-01

The plant availability of residual fertilizer nitrogen for the next crop was studied in chernozem and pseudogley soils. Release of nitrogen was examined after incubation at 3 and 30/sup 0/C. It was found that the use of increased doses of nitrogen fertilizer (ammonium nitrate) led to an increased release of residual fertilizer nitrogen into plant available forms. The release of this nitrogen fraction was 5-10 times faster in comparison with the remaining soil nitrogen.

Survey of pesticide residues in table grapes: Determination of processing factors, intake and risk assessment

DEFF Research Database (Denmark)

Poulsen, Mette Erecius; Hansen, H.K.; Sloth, Jens Jørgen

2007-01-01

of the European Union maximum residue limit (MRL) were found in five samples from Italy. A number of samples were rinsed to study the possible reduction of residues. For copper, iprodione, procymidone and dithiocarbamates a significant effect of rinsing was found (20-49% reduction of residues). However......(-1) for pesticides and 21 mu g day(-1) for copper. Correspondingly, the intakes from South African grapes were 2.6 and 5.7 mu g day(-1) respectively. When the total exposure of pesticides from grapes were related to acceptable daily intake, expressed as the sum of Hazard Quotients, the exposure were...... approximately 0.5% for Italian samples and 1% for South African samples....

Final evaluation of PETC coal conversion solid and hazardous wastes. Final report, September 15, 1977-November 30, 1979. [PETC's own operations

Energy Technology Data Exchange (ETDEWEB)

Neufeld, R.D.; Shapiro, M.; Bern, J.

1979-08-01

Hazards and pollutional impacts from residuals generated at the Pittsburgh Energy Technology Center are explained in the context of hazardous waste regulations proposed by the federal government (RCRA). Nine hazard characteristics are defined and an overview of their significance to PETC is presented. Pollutional impacts on air, water and land are discussed in the energy research perspective. Legislative and statutory relationships between the Center and local, county, state and federal enforcement agencies are listed and analyzed. Expected liability resting on the Center in this framework is outlined. One hundred seven different chemical and indeterminate wastes were reported in an inventory conducted as an earlier task of this project. All of these are tabulated, classified in accordance with the latest proposed federal regulations, with recommended treatment and disposal methodologies included. The existing residuals management system is described to establish baseline conditions in preparing the recommended system. Management policies as they are presently practiced are included in the presentation. A recommended residuals management plan is offered for consideration. It includes the organizational arrangement of PETC personnel, a description of authority and responsibilities of the various human elements of the plan, an information network with detailed data sheets and installation of a mandatory manifest system, a carefully designed hazardous chemical storage area, and short as well as long term choices.

Remaining Sites Verification Package for 100-F-38 Stained Soil Site. Attachment to Waste Site Reclassification Form 2004-093

International Nuclear Information System (INIS)

Carlson, R.A.

2006-01-01

The 100-F-38 Stained Soil site was an area of yellow stained soil that was discovered while excavating a trench for the placement of electrical conduit. The 100-F-38 Stained Soil site meets the remedial action objectives specified in the Remaining Sites ROD. The results of verification sampling show demonstrate that residual contaminant concentrations support future unrestricted land uses that can be represented by a rural-residential scenario. The results also show that residual contaminant concentrations do not preclude any future uses and allow for unrestricted use of shallow zone soils and the contaminant concentrations remaining in the soil are protective of groundwater and the Columbia River

Limitations of Cox Proportional Hazards Analysis in Mortality Prediction of Patients with Acute Coronary Syndrome

Directory of Open Access Journals (Sweden)

Babińska Magdalena

2015-12-01

Full Text Available The aim of this study was to evaluate the possibility of incorrect assessment of mortality risk factors in a group of patients affected by acute coronary syndrome, due to the lack of hazard proportionality in the Cox regression model. One hundred and fifty consecutive patients with acute coronary syndrome (ACS and no age limit were enrolled. Univariable and multivariable Cox proportional hazard analyses were performed. The proportional hazard assumptions were verified using Schoenfeld residuals, χ2 test and rank correlation coefficient t between residuals and time. In the total group of 150 patients, 33 (22.0% deaths from any cause were registered in the follow-up time period of 64 months. The non-survivors were significantly older and had increased prevalence of diabetes and erythrocyturia, longer history of coronary artery disease, higher concentrations of serum creatinine, cystatin C, uric acid, glucose, C-reactive protein (CRP, homocysteine and B-type natriuretic peptide (NT-proBNP, and lower concentrations of serum sodium. No significant differences in echocardiography parameters were observed between groups. The following factors were risk of death factors and fulfilled the proportional hazard assumption in the univariable model: smoking, occurrence of diabetes and anaemia, duration of coronary artery disease, and abnormal serum concentrations of uric acid, sodium, homocysteine, cystatin C and NT-proBNP, while in the multivariable model, the risk of death factors were: smoking and elevated concentrations of homocysteine and NT-proBNP. The study has demonstrated that violation of the proportional hazard assumption in the Cox regression model may lead to creating a false model that does not include only time-independent predictive factors.

Guidance for classification of residues from combustion and incineration in accordance with the Swedish ordinance for waste; Vaegledning foer klassificering av foerbraenningsrester enligt Avfallsfoerordningen

Energy Technology Data Exchange (ETDEWEB)

Adler, Peter [AaF Energi och Miljoe AB, Stockholm (Sweden); Haglund, Jan-Erik [Soederenergi AB, Stockholm (Sweden); Sjoeblom, Rolf [Tekedo AB, Nykoeping (Sweden)

2004-05-01

A new ordinance for waste came into force in Sweden on the first of January 2002, replacing some previous ordinances. The new ordinance is based on certain EU directives and contains amongst other things new rules regarding how certain streams of waste are to be classified into hazardous waste and non-hazardous waste. In a number of cases, the classification is to be made according to whether or not the waste possesses one or more of a number o properties H1 - H14, i e if the waste contains hazardous substances. The new rules are based on the regulation that exists for chemical substances and preparations. When attempts have been made to use these new rules in practice - e g for residues from incineration and combustion - it has become apparent that they are very difficult or even impossible to apply. The primary reason for this is that the residues contain a very large number (thousands) of substances which would have to be analysed and for which the hazard would have to be assessed correctly in accordance with the criteria for the properties (H4 - H8 and H10 - H11). Furthermore, some of the properties listed in the ordinance for waste lack criteria for assessment of hazard. These are H13 (can give rise to another substance which may be hazardous, e g leachate) and H14 (hazardous to the environment). Moreover, there are significant differences between the Ordinance of waste and the regulation of the National Chemicals Inspectorate. It is on the latter that the rules in the Ordinance of waste are based, and this is also the cause of many of the questions and of the uncertainties in the classification. In the present report, a method is developed and described for classification of residues from combustion and incineration. The method is to be applicable in practice without compromising environmental and health aspects. As a part of the present work, a compilation of content and alteration of chemical substances in is carried out. In another chapter, the experience

Detecting organic gunpowder residues from handgun use

Science.gov (United States)

MacCrehan, William A.; Ricketts, K. Michelle; Baltzersen, Richard A.; Rowe, Walter F.

1999-02-01

The gunpowder residues that remain after the use of handguns or improvised explosive devices pose a challenge for the forensic investigator. Can these residues be reliably linked to a specific gunpowder or ammunition? We investigated the possibility by recovering and measuring the composition of organic additives in smokeless powder and its post-firing residues. By determining gunpowder additives such as nitroglycerin, dinitrotoluene, ethyl- and methylcentralite, and diphenylamine, we hope to identify the type of gunpowder in the residues and perhaps to provide evidence of a match to a sample of unfired powder. The gunpowder additives were extracted using an automated technique, pressurized fluid extraction (PFE). The conditions for the quantitative extraction of the additives using neat and solvent-modified supercritical carbon dioxide were investigated. All of the major gunpowder additives can be determined with baseline resolution using capillary electrophoresis (CE) with a micellar agent and UV absorbance detection. A study of candidate internal standards for use in the CE method is also presented. The PFE/CE technique is used to evaluate a new residue sampling protocol--asking shooters to blow their noses. In addition, an initial investigation of the compositional differences among unfired and post-fired .22 handgun residues is presented.

Residual nilpotence and residual solubility of groups

International Nuclear Information System (INIS)

Mikhailov, R V

2005-01-01

The properties of the residual nilpotence and the residual solubility of groups are studied. The main objects under investigation are the class of residually nilpotent groups such that each central extension of these groups is also residually nilpotent and the class of residually soluble groups such that each Abelian extension of these groups is residually soluble. Various examples of groups not belonging to these classes are constructed by homological methods and methods of the theory of modules over group rings. Several applications of the theory under consideration are presented and problems concerning the residual nilpotence of one-relator groups are considered.

The newest achievements of studies on the reutilization, treatment, and disposal technology of hazardous wastes

Energy Technology Data Exchange (ETDEWEB)

Liu Peizhe [Chinese Research Academy of Environmental Sciences, Beijing (China)

1996-12-31

From 1991 to 1996, key studies on the reutilization, treatment, and disposal technology of hazardous wastes have been incorporated into the national plan for environmental protection science and technology. At present, the research achievements have been accomplished, have passed national approval, and have been accepted. The author of this paper, as leader of the national group for this research work, expounds the newest achievements of the studies involving four parts: (1) the reutilization technology of electroplating sludge, including the ion-exchange process for recovering the sludge and waste liquor for producing chromium tanning agent and extracting chromium and colloidal protein from tanning waste residue; on the recovery of heavy metals from the electroplating waste liquor with microbic purification; on the demonstration project of producing modified plastics from the sludge and the waste plastics; and on the demonstration of the recovery of heavy metals from waste electroplating sludge by using the ammonia-leaching process; (2) the demonstrative research of reutilization technology of chromium waste residues, including production of self-melting ore and smelting of chromium-containing pig iron, and of pyrolytic detoxification of the residue with cyclone furnace; (3) the incineration technology of hazardous wastes with successful results of the industrial incinerator system for polychlorinated biphenyls; and (4) the safety landfill technology for disposal of hazardous wastes, with a complete set of technology for pretreatment, selection of the site, development of the antipercolating materials, and design and construction of the landfill. Only a part of the achievements is introduced in this paper, most of which has been built and is being operated for demonstration to further spreading application and accumulate experience. 6 refs., 7 figs., 6 tabs.

PESTICIDES: BENEFITS AND HAZARDS

Directory of Open Access Journals (Sweden)

Ivan Maksymiv

2015-05-01

Full Text Available Pesticides are an integral part of modern life used to prevent growth of unwanted living  organisms. Despite the fact that scientific statements coming from many toxicological works provide indication on the low risk of the pesticides and their residues, the community especially last years is deeply concerned about massive application of pesticides in diverse fields. Therefore evaluation of hazard risks particularly in long term perspective is very important. In the fact there are at least two clearly different approaches for evaluation of pesticide using: the first one is defined as an objective or probabilistic risk assessment, while the second one is the potential economic and agriculture benefits. Therefore, in this review the author has considered scientifically based assessment of positive and negative effects of pesticide application and discusses possible approaches to find balance between them.

The Conversion and Sustainable Use of Alumina Refinery Residues: Global Solution Examples

Science.gov (United States)

Fergusson, Lee

This paper introduces current industry best practice for the conversion of alumina refinery residues (or "red mud") from hazardous waste to benign, inert material. The paper will examine four neutralization methods and Basecon Technology, a sustainable conversion process. The paper will consider ways through which this converted material can be combined and processed for sustainable applications in the treatment of hazardous waste streams (such as industrial wastewater and sludges, biosolids, and CCA wastes), contaminated brownfield sites, and mine site wastes. Recent discoveries and applications, such as the successful treatment of high levels of radium in drinking water in the USA, will also be discussed. Examples of global solutions and their technical merits will be assessed.

Health Risk Assessment of Pesticide Residues via Dietary Intake of Market Vegetables from Dhaka, Bangladesh

Directory of Open Access Journals (Sweden)

Md. Shakhaoat Hossain

2013-02-01

Full Text Available The present study was designed to assess the health risk of pesticide residues via dietary intake of vegetables collected from four top agro-based markets of Dhaka, Bangladesh. High performance liquid chromatography with a photo diode array detector (HPLC-PDA was used to determine six organophosphorus (chlorpyrifos, fenitrothion, parathion, ethion, acephate, fenthion, two carbamate (carbaryl and carbofuran and one pyrethroid (cypermethrin pesticide residues in twelve samples of three common vegetables (tomato, lady’s finger and brinjal. Pesticide residues ranged from below detectable limit (<0.01 to 0.36 mg/kg. Acephate, chlorpyrifos, ethion, carbaryl and cypermethrin were detected in only one sample, while co-occurrence occurred twice for fenitrothion and parathion. Apart from chlorpyrifos in tomato and cypermethrin in brinjal, all pesticide residues exceeded the maximum residue limit (MRL. Hazard risk index (HRI for ethion (10.12 and carbaryl (1.09 was found in lady’s finger and tomato, respectively. Rest of the pesticide residues were classified as not a health risk. A continuous monitoring and strict regulation should be enforced regarding control of pesticide residues in vegetables and other food commodities.

Risk Analysis on Organochlorine Pesticides Residue in Potato and Carrot from Conventional and Organic Farms in Citarum Watershed Area, West Java Province, Indonesia

Directory of Open Access Journals (Sweden)

Suphia Rahmawati

2017-03-01

Full Text Available Six samples of carrot and potatoes were collected from conventional and organic farms. Organochlorine pesticides (OCPs residue was analyzed using liquid-liquid extraction. The concentration of OCPs residue together with the consumption pattern were used to calculate the potential risk. Estimated Daily Intake (EDI of OCPs residue in carrots and potatoes both from conventional and organic farms were below the standard given in SNI 7313:2008 and the Maximum Residue Limit (MRLs from USEPA . Hazard quotient (HQ and Hazard Index (HI as effect analysis were below the unity, thus there may not be a concern for non-carcinogenic effect. Risk analysis on cancer effects indicated that potatoes samples were above the recommended risk by EPA (10-6. In addition, risk of potatoes samples from organic samples was higher compare to that of the conventional farm. Cancer risk analysis of carrot samples were found below the recommended risk by EPA. Cancer risk effect of carrot samples from conventional farm was slightly higher compare to that of the organic farm.

Monitoring of Benomyl Residue in Mushroom Marketed in Hamadan City

Directory of Open Access Journals (Sweden)

S. Abdi

2015-07-01

Full Text Available Introduction & Objective: Pesticide residues in environment and food have a negative impact on the health of living organisms. Therefore, this study was carried out for evaluation of benomyl residues in mushroom marketed in Hamadan city in 2014 using spectrophotometry. Materials & Methods: 10 specimens of mushroom were collected from greenhouses and market basket of Hamadan city. After preparation and processing the samples in the laboratory, be-nomyl residues in samples were determined using a spectrophotometric method in 3 replica-tions. All statistical analyses were performed using the SPSS statistical package. Results: The mean concentration of benomyl residues in samples were 5.90±0.75, 2.10± 0.487, 40.04±1.346, 0.32±0.044, 14.0±0.785, 1.54±0.304, 40.0±0.45, 0.87±0.055, 0.66± 0.032 and 49.60±0.303 µg kg-1 and more than the maximum residue limit (MRL provided by the World Health Organization (10 ppb. The results of the comparison of the mean concentration of pesticide residues among samples revealed significant differences in most of the samples (P<0.05. Conclusion: The results showed that mean concentrations of benomyl residues in mushroom samples were exceeding that of the MRL. Therefore, it is essential to impart proper education to the farming community about hazards involved in the overuse of toxic pesticides. Also, codification of laws and their enforcement and implementation of programs for the regular periodic monitoring of pesticide residues in foodstuffs especially in vegetables cultivated un-der greenhouse conditions at the national level to protect consumers’ health are recom-mended.(Sci J Hamadan Univ Med Sci 2015; 22 (2: 137-143

Remaining Sites Verification Package for the 100-C-9:2 Sanitary Sewer Pipelines, Waste Site Reclassification Form 2004-013

Energy Technology Data Exchange (ETDEWEB)

L. M. Dittmer

2007-07-11

The 100-C-9:2 sanitary sewer pipelines include the feeder pipelines associated with the 1607-B8, the 1607-B9, the 1607-B10 and the 1607-B11 septic systems. Contaminated soil and piping from the feeder lines to the septic systems were removed and disposed of. The remaining soil in the excavations has been shown to meet the remedial action objectives specified in the Remaining Sites ROD. The results of verification sampling show that residual contaminant concentrations do not preclude any future uses and allow for unrestricted use of shallow zone soils. The results also demonstrate that residual contaminant concentrations are protective of groundwater and the Columbia River.

Radioactivity of combustion residues from coal-fired power stations

International Nuclear Information System (INIS)

Vom Berg, W.; Puch, K.H.

1996-01-01

Each year in Germany, about 18 mill. t of combustion residues are produced from the combustion of bituminous coal and lignite. They are utilized to a great extent in the construction industry and in mining. During the combustion of coal, the radio-nuclides remain predominantly in the ash. The radionuclide concentration in lignite ash is within the range of that in natural soil. The combustion residues of bituminous coal contain radio-nuclides of a similar order of magnitude as also can occur in natural rock. The utilization of combustion residues in construction materials makes a negligible contribution to radiation exposure through retention in buildings. (orig.) [de

Residues of {sup 14}C-paclobutrazol in mangoes

Energy Technology Data Exchange (ETDEWEB)

Costa, Maria A.; Tornisielo, Valdemar L.; Castanho, Giuliane M., E-mail: macosta@cena.usp.b [Centro de Energia Nuclear na Agricultura (CENA/USP), Piracicaba, SP (Brazil). Lab. de Ecotoxicologia

2009-07-01

Paclobutrazol (PBZ) is a growth regulator used in agricultural systems whose purpose is the control of vegetative growth, stimulating the reproductive capacity of plants. This growth regulator remains active in soil for a long time and its half-life varies with the type of soil and climatic conditions, can severely affect the development of crops. This work aimed to study the residues / metabolites of {sup 14}C-PBZ in mango pulp Tommy Atkins. The tests were performed with mangoes grown in pots stainless steel and application of {sup 14}C-PBZ was performed by the soil projection of the crown, and the mangoes tested in two periods, one year and two years after application. To evaluate the levels of residues of {sup 14}C-PBZ was realize the burning of 200 mg of pulp on biological oxidized and detached {sup 14}CO{sub 2} was detected by liquid scintillation spectrophotometer. The results were 1.65 % of residue of PBZ on fruit collected after two years of application and 4.30 % of residue of PBZ collected on fruit after a year of application and also can see that the product remained in the soil for more than one year, is translocated to the plant and reach the edible part, the pulp fruit. The identification of residual {sup 14}C- PBZ/metabolites by thin-layer chromatography did not reveal any pattern of PBZ / metabolites due to the low activity detected in the samples. Therefore, another procedure was performed for extraction and then analyzed by high performance liquid chromatography (HPLC) for detection of metabolites in the PBZ of mango pulp. (author)

Acid transformation of bauxite residue: Conversion of its alkaline characteristics.

Science.gov (United States)

Kong, Xiangfeng; Li, Meng; Xue, Shengguo; Hartley, William; Chen, Chengrong; Wu, Chuan; Li, Xiaofei; Li, Yiwei

2017-02-15

Bauxite residue (BR) is a highly alkaline solid hazardous waste produced from bauxite processing for alumina production. Alkaline transformation appears to reduce the environmental risk of bauxite residue disposal areas (BRDAs) whilst potentially providing opportunities for the sustainable reuse and on-going management of BR. Mineral acids, a novel citric acid and a hybrid combination of acid-gypsum treatments were investigated for their potential to reduce residue pH and total alkalinity and transform the alkaline mineral phase. XRD results revealed that with the exception of andradite, the primary alkaline solid phases of cancrinite, grossular and calcite were transformed into discriminative products based on the transformation used. Supernatants separated from BR and transformed bauxite residue (TBR) displayed distinct changes in soluble Na, Ca and Al, and a reduction in pH and total alkalinity. SEM images suggest that mineral acid transformations promote macro-aggregate formation, and the positive promotion of citric acid, confirming the removal or reduction in soluble and exchangeable Na. NEXAFS analysis of Na K-edge revealed that the chemical speciation of Na in TBRs was consistent with BR. Three acid treatments and gypsum combination had no effect on Na speciation, which affects the distribution of Na revealed by sodium STXM imaging. Copyright © 2016 Elsevier B.V. All rights reserved.

Biosorbents for Removing Hazardous Metals and Metalloids

Directory of Open Access Journals (Sweden)

Katsutoshi Inoue

2017-07-01

Full Text Available Biosorbents for remediating aquatic environmental media polluted with hazardous heavy metals and metalloids such as Pb(II, Cr(VI, Sb(III and V, and As(III and V were prepared from lignin waste, orange and apple juice residues, seaweed and persimmon and grape wastes using simple and cheap methods. A lignophenol gel such as lignocatechol gel was prepared by immobilizing the catechol functional groups onto lignin from sawdust, while lignosulfonate gel was prepared directly from waste liquor generated during pulp production. These gels effectively removed Pb(II. Orange and apple juice residues, which are rich in pectic acid, were easily converted using alkali (e.g., calcium hydroxide into biosorbents that effectively removed Pb(II. These materials also effectively removed Sb(III and V and As(III and V when these were preloaded with multi-valent metal ions such as Zr(IV and Fe(III. Similar biosorbents were prepared from seaweed waste, which is rich in alginic acid. Other biosorbents, which effectively removed Cr(VI, were prepared by simply treating persimmon and grape wastes with concentrated sulfuric acid.

TREATMENT OF METAL-LADEN HAZARDOUS WASTES WITH ADVANCED CLEAN COAL TECHNOLOGY BY-PRODUCTS

Energy Technology Data Exchange (ETDEWEB)

James T. Cobb, Jr.

2003-09-12

Metal-laden wastes can be stabilized and solidified using advanced clean coal technology by-products (CCTBs)--fluid bed combustor ash and spray drier solids. These utility-generated treatment chemicals are available for purchase through brokers, and commercial applications of this process are being practiced by treaters of metal-laden hazardous waste. A complex of regulations governs this industry, and sensitivities to this complex has discouraged public documentation of treatment of metal-laden hazardous wastes with CCTBs. This report provides a comprehensive public documentation of laboratory studies that show the efficacy of the stabilization and solidification of metal-laden hazardous wastes--such as lead-contaminated soils and sandblast residues--through treatment with CCTBs. It then describes the extensive efforts that were made to obtain the permits allowing a commercial hazardous waste treater to utilize CCTBs as treatment chemicals and to install the equipment required to do so. It concludes with the effect of this lengthy process on the ability of the treatment company to realize the practical, physical outcome of this effort, leading to premature termination of the project.

Solid and hazardous waste management practices onboard ocean going vessels: a review.

Science.gov (United States)

Swamy, Yeddanapudi V R P P

2012-01-01

Shipping or carriage of goods play an important role in the development of human societies and international shipping industry, which carries 90% of the world trade, is the life blood of global economy. During ships operational activity a number of solid and hazardous wastes, also referred as garbage are produced from galleys, crew cabins and engine/deck departments stores. This review provides an overview of the current practices onboard and examines the evidence that links waste management plan regulations to shipping trade. With strict compliance to International Maritime Organization's MARPOL regulations, which prevents the pollution of sea from ships various discharges, well documented solid and hazardous waste management practices are being followed onboard ships. All ship board wastes are collected, segregated, stored and disposed of in appropriate locations, in accordance with shipping company's environmental protection policy and solid and hazardous waste management plan. For example, food residues are ground onboard and dropped into the sea as fish food. Cardboard and the like are burned onboard in incinerators. Glass is sorted into dark/light and deposited ashore, as are plastics, metal, tins, batteries, fluorescent tubes, etc. The residue from plastic incineration which is still considered as plastic is brought back to shore for disposal. New targets are being set up to reduce the volume of garbage generated and disposed of to shore facilities, and newer ships are using baling machines which compress cardboard etc into bales to be taken ashore. The garbage management and its control system work as a 'continual improvement' process to achieve new targets.

Enhanced Contaminated Human Remains Pouch: initial development and preliminary performance assessments

Energy Technology Data Exchange (ETDEWEB)

Iseli, A.M.; Kwen, H.D.; Ul-Alam, M.; Balasubramanian, M.; Rajagopalan, S.

2011-11-07

The objective is to produce a proof of concept prototype Enhanced Contaminated Human Remains Pouch (ECHRP) with self-decontamination capability to provide increased protection to emergency response personnel. The key objective was to decrease the concentration of toxic chemicals through the use of an absorbent and reactive nanocellulose liner. Additionally, nanomaterials with biocidal properties were developed and tested as a 'stand-alone' treatment. The setting was a private company research laboratory. The main outcome measures were production of a functional prototype. A functional prototype capable of mitigating the threats due to sulfur mustard, Soman, and a large variety of liquid and vapor toxic industrial chemicals was produced. Stand-alone biocidal treatment efficacy was validated. The ECHRP provides superior protection from both chemical and biological hazards to various emergency response personnel and human remains handlers.

Remaining Sites Verification Package for the 1607-F4 Sanitary Sewer System. Attachment to Waste Site Reclassification Form 2004-131

International Nuclear Information System (INIS)

Dittmer, L.M.

2007-01-01

The 1607-F4 waste site is the former location of the sanitary sewer system that serviced the former 115-F Gas Recirculation Building. The system included a septic tank, drain field, and associated pipeline that were in use from 1944 to 1965. The 1607-F4 waste site received unknown amounts of sanitary sewage from the 115-F Gas Recirculation Building and may have potentially contained hazardous and radioactive contamination. In accordance with this evaluation, the verification sampling results support a reclassification of this site to Interim Closed Out. The results of verification sampling demonstrated that residual contaminant concentrations do not preclude any future uses and allow for unrestricted use of shallow zone soils. The results also showed that residual contaminant concentrations are protective of groundwater and the Columbia River

NPR hazards review: (Phase 1, Production only appendixes). Volume 2

Energy Technology Data Exchange (ETDEWEB)

Miller, N.R.; Trumble, R.E.

1962-08-15

The NPR Hazards Review is being issued in a series of volumes. Volume 1, which has already been published, was of the nature of an expanded summary. It included the results of hazards analyses with some explanatory material to put the results in context. Volume 2 presents results of reviews made after the preparation of Volume 1. It also contains supporting material and details not included in Volume 1. Volumes 1 and 2 together provide a nearly complete ``Design Hazards Review of the NPR.`` However, certain remaining problems still exist and are to be the subject of a continuing R&D program. These problems and programs are discussed in Appendix H. Neither Volume 1 nor Volume 2 treat operational aspects of reactor hazards in detail. This area of concern will be the primary subject of a third volume of the NPR Hazards Review. This third volume, to be prepared and issued at a later date, may also contain information supplementing Volumes 1 and 2.

Transportation of Hazardous Materials Emergency Preparedness Hazards Assessment

Energy Technology Data Exchange (ETDEWEB)

Blanchard, A.

2000-02-28

This report documents the Emergency Preparedness Hazards Assessment (EPHA) for the Transportation of Hazardous Materials (THM) at the Department of Energy (DOE) Savannah River Site (SRS). This hazards assessment is intended to identify and analyze those transportation hazards significant enough to warrant consideration in the SRS Emergency Management Program.

Transportation of Hazardous Materials Emergency Preparedness Hazards Assessment

International Nuclear Information System (INIS)

Blanchard, A.

2000-01-01

This report documents the Emergency Preparedness Hazards Assessment (EPHA) for the Transportation of Hazardous Materials (THM) at the Department of Energy (DOE) Savannah River Site (SRS). This hazards assessment is intended to identify and analyze those transportation hazards significant enough to warrant consideration in the SRS Emergency Management Program

Transportation of hazardous materials emergency preparedness hazards assessment

International Nuclear Information System (INIS)

Blanchard, A.

2000-01-01

This report documents the Emergency Preparedness Hazards Assessment (EPHA) for the Transportation of Hazardous Materials (THM) at the Department of Energy (DOE) Savannah River Site (SRS). This hazards assessment is intended to identify and analyze those transportation hazards significant enough to warrant consideration in the SRS Emergency Management Program

Landfill Mining of Shredder Residues

DEFF Research Database (Denmark)

Hansen, Jette Bjerre; Hyks, Jiri; Shabeer Ahmed, Nassera

In Denmark, shredder residues (SR) are classified as hazardous waste and until January 2012 the all SR were landfilled. It is estimated that more than 1.8 million tons of SR have been landfilled in mono cells. This paper describes investigations conducted at two Danish landfills. SR were excavated...... from the landfills and size fractionated in order to recover potential resources such as metal and energy and to reduce the amounts of SR left for re-landfilling. Based on the results it is estimated that 60-70% of the SR excavated could be recovered in terms of materials or energy. Only a fraction...... with particle size less than 5 mm needs to be re-landfilled at least until suitable techniques are available for recovery of materials with small particle sizes....

On the ASR and ASR thermal residues characterization of full scale treatment plant.

Science.gov (United States)

Mancini, G; Viotti, P; Luciano, A; Fino, D

2014-02-01

In order to obtain 85% recycling, several procedures on Automotive Shredder Residue (ASR) could be implemented, such as advanced metal and polymer recovery, mechanical recycling, pyrolysis, the direct use of ASR in the cement industry, and/or the direct use of ASR as a secondary raw material. However, many of these recovery options appear to be limited, due to the possible low acceptability of ASR based products on the market. The recovery of bottom ash and slag after an ASR thermal treatment is an option that is not usually considered in most countries (e.g. Italy) due to the excessive amount of contaminants, especially metals. The purpose of this paper is to provide information on the characteristics of ASR and its full-scale incineration residues. Experiments have been carried out, in two different experimental campaigns, in a full-scale tyre incineration plant specifically modified to treat ASR waste. Detailed analysis of ASR samples and combustion residues were carried out and compared with literature data. On the basis of the analytical results, the slag and bottom ash from the combustion process have been classified as non-hazardous wastes, according to the EU waste acceptance criteria (WAC), and therefore after further tests could be used in future in the construction industry. It has also been concluded that ASR bottom ash (EWC - European Waste Catalogue - code 19 01 12) could be landfilled in SNRHW (stabilized non-reactive hazardous waste) cells or used as raw material for road construction, with or without further treatment for the removal of heavy metals. In the case of fly ash from boiler or Air Pollution Control (APC) residues, it has been found that the Cd, Pb and Zn concentrations exceeded regulatory leaching test limits therefore their removal, or a stabilization process, would be essential prior to landfilling the use of these residues as construction material. Copyright © 2013 Elsevier Ltd. All rights reserved.

Removal of residual particulate matter from filter media

Science.gov (United States)

Almlie, Jay C; Miller, Stanley J

2014-11-11

A method for removing residual filter cakes that remain adhered to a filter after typical particulate removal methodologies have been employed, such as pulse-jet filter element cleaning, for all cleanable filters used for air pollution control, dust control, or powder control.

Quantification and characterization of cotton crop biomass residue

Science.gov (United States)

Cotton crop residual biomass remaining in the field after mechanical seed cotton harvest is not typically harvested and utilized off-site thereby generating additional revenue for producers. Recently, interest has increased in utilizing biomass materials as feedstock for the production of fuel and ...

Removal of residual particulate matter from filter media

Energy Technology Data Exchange (ETDEWEB)

Almlie, Jay C.; Miller, Stanley J.

2018-01-09

A method for removing residual filter cakes that remain adhered to a filter after typical particulate removal methodologies have been employed, such as pulse-jet filter element cleaning, for all cleanable filters used for air pollution control, dust control, or powder control.

An Update on the Hazards and Risks of Forensic Anthropology, Part II: Field and Laboratory Considerations.

Science.gov (United States)

Roberts, Lindsey G; Dabbs, Gretchen R; Spencer, Jessica R

2016-01-01

This paper focuses on potential hazards and risks to forensic anthropologists while working in the field and laboratory in North America. Much has changed since Galloway and Snodgrass published their seminal article addressing these issues. The increased number of forensic practitioners combined with new information about potential hazards calls for an updated review of these pathogens and chemicals. Discussion of pathogen hazards (Brucella, Borrelia burgdorferi, Yersinia pestis, Clostridium tetani and West Nile virus) includes important history, exposure routes, environmental survivability, early symptoms, treatments with corresponding morbidity and mortality rates, and decontamination measures. Additionally, data pertaining to the use of formaldehyde in the laboratory environment have resulted in updated safety regulations, and these are highlighted. These data should inform field and laboratory protocols. The hazards of working directly with human remains are discussed in a companion article, "An Update on the Hazards and Risks of Forensic Anthropology, Part I: Human Remains." © 2015 American Academy of Forensic Sciences.

Hazard function theory for nonstationary natural hazards

Science.gov (United States)

Read, L.; Vogel, R. M.

2015-12-01

Studies from the natural hazards literature indicate that many natural processes, including wind speeds, landslides, wildfires, precipitation, streamflow and earthquakes, show evidence of nonstationary behavior such as trends in magnitudes through time. Traditional probabilistic analysis of natural hazards based on partial duration series (PDS) generally assumes stationarity in the magnitudes and arrivals of events, i.e. that the probability of exceedance is constant through time. Given evidence of trends and the consequent expected growth in devastating impacts from natural hazards across the world, new methods are needed to characterize their probabilistic behavior. The field of hazard function analysis (HFA) is ideally suited to this problem because its primary goal is to describe changes in the exceedance probability of an event over time. HFA is widely used in medicine, manufacturing, actuarial statistics, reliability engineering, economics, and elsewhere. HFA provides a rich theory to relate the natural hazard event series (x) with its failure time series (t), enabling computation of corresponding average return periods and reliabilities associated with nonstationary event series. This work investigates the suitability of HFA to characterize nonstationary natural hazards whose PDS magnitudes are assumed to follow the widely applied Poisson-GP model. We derive a 2-parameter Generalized Pareto hazard model and demonstrate how metrics such as reliability and average return period are impacted by nonstationarity and discuss the implications for planning and design. Our theoretical analysis linking hazard event series x, with corresponding failure time series t, should have application to a wide class of natural hazards.

Hazard function theory for nonstationary natural hazards

Science.gov (United States)

Read, Laura K.; Vogel, Richard M.

2016-04-01

Impact from natural hazards is a shared global problem that causes tremendous loss of life and property, economic cost, and damage to the environment. Increasingly, many natural processes show evidence of nonstationary behavior including wind speeds, landslides, wildfires, precipitation, streamflow, sea levels, and earthquakes. Traditional probabilistic analysis of natural hazards based on peaks over threshold (POT) generally assumes stationarity in the magnitudes and arrivals of events, i.e., that the probability of exceedance of some critical event is constant through time. Given increasing evidence of trends in natural hazards, new methods are needed to characterize their probabilistic behavior. The well-developed field of hazard function analysis (HFA) is ideally suited to this problem because its primary goal is to describe changes in the exceedance probability of an event over time. HFA is widely used in medicine, manufacturing, actuarial statistics, reliability engineering, economics, and elsewhere. HFA provides a rich theory to relate the natural hazard event series (X) with its failure time series (T), enabling computation of corresponding average return periods, risk, and reliabilities associated with nonstationary event series. This work investigates the suitability of HFA to characterize nonstationary natural hazards whose POT magnitudes are assumed to follow the widely applied generalized Pareto model. We derive the hazard function for this case and demonstrate how metrics such as reliability and average return period are impacted by nonstationarity and discuss the implications for planning and design. Our theoretical analysis linking hazard random variable X with corresponding failure time series T should have application to a wide class of natural hazards with opportunities for future extensions.

Volcanology and hazards of phreatomagmatic basaltic eruptions

DEFF Research Database (Denmark)

Schmith, Johanne

Iceland is one of the most active terrestrial volcanic regions on Earth with an average of more than 20 eruptions per century. Around 80% of all events are tephra generating explosive eruptions, but less than 10 % of all known tephra layers have been mapped. Recent hazard assessment models show...... that the two key parameters for hazard assessment modeling are total grain size distribution (TGSD) and eruptive style. These two parameters have been determined for even fewer eruptive events in Iceland. One of the most hazardous volcanoes in Iceland is Katla and no data set of TGSD or other eruptive...... parameters exist. Katla has not erupted for 99 years, but at least 2 of the 20 eruptions since the settlement of Iceland in 871 have reached Northern Europe as visible tephra fall. These eruptions occurred in 1755 and 1625 and remain enigmatic both in terms of actual size and eruption dynamics. This work...

Recovery of Trace and Heavy Metals from Coal Combustion Residues for Reuse and Safe Disposal: A Review

Science.gov (United States)

Kumar, Ashvani; Samadder, Sukha Ranjan; Elumalai, Suresh Pandian

2016-09-01

The safe disposal of coal combustion residues (CCRs) will remain a major public issue as long as coal is used as a fuel for energy production. Both dry and wet disposal methods of CCRs create serious environmental problems. The dry disposal method creates air pollution initially, and the wet disposal method creates water pollution as a result of the presence of trace and heavy metals. These leached heavy metals from fly ash may become more hazardous when they form toxic compounds such as arsenic sulfite (As2S3) and lead nitrate (N2O6Pb). The available studies on trace and heavy metals present in CCRs cannot ensure environmentally safe utilization. In this work, a novel approach has been offered for the retrieval of trace and heavy metals from CCRs. If the proposed method becomes successful, then the recovered trace and heavy metals may become a resource and environmentally safe use of CCRs may be possible.

Hazards assessment for the Hazardous Waste Storage Facility

International Nuclear Information System (INIS)

Knudsen, J.K.; Calley, M.B.

1994-04-01

This report documents the hazards assessment for the Hazardous Waste Storage Facility (HWSF) located at the Idaho National Engineering Laboratory. The hazards assessment was performed to ensure that this facility complies with DOE and company requirements pertaining to emergency planning and preparedness for operational emergencies. The hazards assessment identifies and analyzes hazards that are significant enough to warrant consideration in a facility's operational emergency management program. The area surrounding HWSF, the buildings and structures at HWSF, and the processes used at HWSF are described in this report. All nonradiological hazardous materials at the HWSF were identified (radiological hazardous materials are not stored at HWSF) and screened against threshold quantities according to DOE Order 5500.3A guidance. Two of the identified hazardous materials exceeded their specified threshold quantity. This report discusses the potential release scenarios and consequences associated with an accidental release for each of the two identified hazardous materials, lead and mercury. Emergency considerations, such as emergency planning zones, emergency classes, protective actions, and emergency action levels, are also discussed based on the analysis of potential consequences. Evaluation of the potential consequences indicated that the highest emergency class for operational emergencies at the HWSF would be a Site Area Emergency

Pesticide residues in birds and mammals

Science.gov (United States)

Stickel, L.F.; Edwards, C.A.

1973-01-01

exposure to an organochlorine pesticide, the concentrations of residues in the different tissues are ordinarily directly correlated with each other. When the dosage is at lethal levels, or when stored residues are mobilised to lethal levels, the balanced relationship is disrupted. The concentrations of residues in the brain provide the most rigorous criteria for diagnosis of death due to these chemicals, and levels are generally similar across a wide range of species of birds and mammals. Residues in liver are closely correlated with recent dose, either from direct intake or from mobilisation from storage, and so reflect hazardous exposure. Residues in the whole carcass show the storage reserve, and so indicate the potential for adverse effects from lethal mobilisation or from the continuous slow mobilisation that occurs during the normal processes of metabolism and excretion. A synchronous, rapid, and widespread decline in weight and thickness of shells of eggs laid by many species of wild birds occurred in the late 1940's and has persisted. Birds of prey were primarily affected; exceptions apparently are the result of lesser exposure because of different food habits. Many species of fish-eating birds are also affected. Others, however, appear to be more resistant and to accumulate much higher residues before shell-thinning occurs. Seed-eating birds do not appear to have been generally affected; their exposure is ordinarily lower, but physiological factors also seem to be involved. A relationship between shell-thinning and population decline has been established for many species. In exceptional cases, such as the herring gull, persistent re-nesting and other population reactions have overcome adverse effects at the population level. The discovery of shell-thinning among natural populations, and the hypothesis that this thinning was related to the occurrence of organochlorine pesticides, stimulated experimental studies to determine wheth

Chemical hazard evaluation of material disposal area (MDA) B closure project

Energy Technology Data Exchange (ETDEWEB)

Laul, Jagdish C [Los Alamos National Laboratory

2010-04-19

TA-21, MDA-B (NES) is the 'contaminated dump,' landfill with radionuclides and chemicals from process waste disposed in 1940s. This paper focuses on chemical hazard categorization and hazard evaluation of chemicals of concern (e.g., peroxide, beryllium). About 170 chemicals were disposed in the landfill. Chemicals included products, unused and residual chemicals, spent, waste chemicals, non-flammable oils, mineral oil, etc. MDA-B was considered a High hazard site. However, based on historical records and best engineering judgment, the chemical contents are probably at best 5% of the chemical inventory. Many chemicals probably have oxidized, degraded or evaporated for volatile elements due to some fire and limited shelf-life over 60 yrs, which made it possible to downgrade from High to Low chemical hazard site. Knowing the site history and physical and chemical properties are very important in characterizing a NES site. Public site boundary is only 20 m, which is a major concern. Chemicals of concern during remediation are peroxide that can cause potential explosion and beryllium exposure due to chronic beryllium disease (CBD). These can be prevented or mitigated using engineering control (EC) and safety management program (SMP) to protect the involved workers and public.

Presence of pesticide residues on produce cultivated in Suriname.

Science.gov (United States)

Abdoel Wahid, F; Wickliffe, J; Wilson, M; Van Sauers, A; Bond, N; Hawkins, W; Mans, D; Lichtveld, M

2017-06-01

Agricultural pesticides are widely used in Suriname, an upper middle-income Caribbean country located in South America. Suriname imported 1.8 million kg of agricultural pesticides in 2015. So far, however, national monitoring of pesticides in crops is absent. Reports from the Netherlands on imported Surinamese produce from 2010 to 2015 consistently showed that samples exceeded plant-specific pesticide maximum residue limits (MRLs) of the European Union (EU). Consumption of produce containing unsafe levels of pesticide residues can cause neurological disorders, and particularly, pregnant women and children may be vulnerable. This pilot study assessed the presence of pesticide residues in commonly consumed produce items cultivated in Suriname. Thirty-two insecticides (organophosphates, organochlorines, carbamates, and pyrethroids) and 12 fungicides were evaluated for their levels in nine types of produce. Pesticide residue levels exceeding MRLs in this study regarded cypermethrin (0.32 μg/g) in tomatoes (USA MRL 0.20 μg/g), lambda-cyhalothrin (1.08 μg/g) in Chinese cabbage (USA MRL 0.40 μg/g), endosulfan (0.07 μg/g) in tannia (EU MRL 0.05 μg/g), and lindane (0.02 and 0.03 μg/g, respectively) in tannia (EU MRL 0.01 μg/g). While only a few pesticide residues were detected in this small pilot study, these residues included two widely banned pesticides (endosulfan and lindane). There is a need to address environmental policy gaps. A more comprehensive sampling and analysis of produce from Suriname is warranted to better understand the scope of the problem. Preliminary assessments, using intake rate, hazard quotient, and level of concern showed that it is unlikely that daily consumption of tannia leads to adverse health effects.

Report 6: Guidance document. Man-made hazards and Accidental Aircraft Crash hazards modelling and implementation in extended PSA

International Nuclear Information System (INIS)

Kahia, S.; Brinkman, H.; Bareith, A.; Siklossy, T.; Vinot, T.; Mateescu, T.; Espargilliere, J.; Burgazzi, L.; Ivanov, I.; Bogdanov, D.; Groudev, P.; Ostapchuk, S.; Zhabin, O.; Stojka, T.; Alzbutas, R.; Kumar, M.; Nitoi, M.; Farcasiu, M.; Borysiewicz, M.; Kowal, K.; Potempski, S.

2016-01-01

analysis. As it was recommended by end users (WP10), this guidance covers questions of developing integrated and/or separated man-made PSA models. Methods to model the combinations/correlations/dependencies of hazards, possible secondary effects, mitigating and aggravating factors are also proposed in the report. This report contains approaches to model mobile equipment but despite this fact, input data related to this (reliability and related human actions, assessment of time for its running) remains a source of significant uncertainty. From an industrial end-user perspective, the PSA methodology must be proportionate to the importance of risks (this can be also required by national laws such as the French Law). The adoption of a graded approach for External Hazards PSA would better focus resources and direct them to identify and address issues that present the highest significance to NPP Risks and Safety. Therefore, there is no relevance to use complex methodologies if a simplified analysis gives sufficient and representative insights. (authors)

Impact of residual pulmonary obstruction on the long-term outcome of patients with pulmonary embolism.

Science.gov (United States)

Pesavento, Raffaele; Filippi, Lucia; Palla, Antonio; Visonà, Adriana; Bova, Carlo; Marzolo, Marco; Porro, Fernando; Villalta, Sabina; Ciammaichella, Maurizio; Bucherini, Eugenio; Nante, Giovanni; Battistelli, Sandra; Muiesan, Maria Lorenza; Beltramello, Giampietro; Prisco, Domenico; Casazza, Franco; Ageno, Walter; Palareti, Gualtiero; Quintavalla, Roberto; Monti, Simonetta; Mumoli, Nicola; Zanatta, Nello; Cappelli, Roberto; Cattaneo, Marco; Moretti, Valentino; Corà, Francesco; Bazzan, Mario; Ghirarduzzi, Angelo; Frigo, Anna Chiara; Miniati, Massimo; Prandoni, Paolo

2017-05-01

The impact of residual pulmonary obstruction on the outcome of patients with pulmonary embolism is uncertain.We recruited 647 consecutive symptomatic patients with a first episode of pulmonary embolism, with or without concomitant deep venous thrombosis. They received conventional anticoagulation, were assessed for residual pulmonary obstruction through perfusion lung scanning after 6 months and then were followed up for up to 3 years. Recurrent venous thromboembolism and chronic thromboembolic pulmonary hypertension were assessed according to widely accepted criteria.Residual pulmonary obstruction was detected in 324 patients (50.1%, 95% CI 46.2-54.0%). Patients with residual pulmonary obstruction were more likely to be older and to have an unprovoked episode. After a 3-year follow-up, recurrent venous thromboembolism and/or chronic thromboembolic pulmonary hypertension developed in 34 out of the 324 patients (10.5%) with residual pulmonary obstruction and in 15 out of the 323 patients (4.6%) without residual pulmonary obstruction, leading to an adjusted hazard ratio of 2.26 (95% CI 1.23-4.16).Residual pulmonary obstruction, as detected with perfusion lung scanning at 6 months after a first episode of pulmonary embolism, is an independent predictor of recurrent venous thromboembolism and/or chronic thromboembolic pulmonary hypertension. Copyright ©ERS 2017.

What remains of the Arrow oil?

International Nuclear Information System (INIS)

Sergy, G.; Owens, E.

1993-01-01

In February 1970, the tanker Arrow became grounded 6.5 km off the north shore of Chedabucto Bay, Nova Scotia, and nearly 72,000 bbl of Bunker C fuel oil were released from the vessel during its subsequent breakup and sinking. The oil was washed ashore in various degrees over an estimated 305 km of the bay's 604-km shoreline, of which only 48 km were cleaned. In addition, the tanker Kurdistan broke in two in pack ice in March 1979 in the Cabot Strait area, spilling ca 54,000 bbl of Bunker C, some of which was later found at 16 locations along the northeast and east shorelines of Chedabucto Bay. In summer 1992, a systematic ground survey of the bay's shorelines was conducted using Environment Canada Shoreline Cleanup Assessment Team (SCAT) procedures. Standard observations were made of oil distribution and width, thickness, and character of the oil residues in 419 coastal segments. Results from the survey are summarized. Oil was found to be present on 13.3 km of the shoreline, with heavy oiling restricted to 1.3 km primarily in the areas of Black Duck Cove and Lennox Passage. Some of this residual oil was identified as coming from the Arrow. Natural weathering processes account for removal of most of the spilled oil from the bay. Oil remaining on the shore was found in areas outside of the zone of physical wave action, in areas of nearshore mixing where fine sediments are not present to weather the oil through biophysical processes, or in crusts formed by oil weathered on the surface. The systematic description of oiled shorelines using the SCAT methodology proved very successful, even for such an old spill. 6 refs

Obtention of ceramic pigments with residue from electroplating; Obtencao de pigmentos ceramicos a partir de residuo de galvanoplastia

Energy Technology Data Exchange (ETDEWEB)

Boss, A. [Servico Nacional de Aprendizagem Industrial (SENAI), Tijucas, SC (Brazil); Kniess, C.T. [Universidade Nove de Julho (UNINOVE), SP (Brazil); Aguiar, B.M. de [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil); Prates, P.B.; Milanez, K., E-mail: kniesscl@gmail.com [Universidade Federal de Santa Catarina (EMC/UFSC), SC (Brazil). Depto de Engenharia Mecanica

2011-07-01

The incorporation of industrial residues in industrial processes opens up new business opportunities and reduces the volume of extraction of raw materials, preserving natural resources, which are limited. An important residue is the mud from galvanic industry, consisting of alkali and transition metals. According to NBR 10004/2004, this residue can be classified as Class I (hazardous), depending on the concentration of metals present in the mud. This paper proposes a method for reusing the residue from electroplating in ceramic pigments. The characterization of residual plating was obtained by chemical analysis, mineralogical analysis and pH measurements. The electroplating waste was incorporated in different percentages on a standard pigment formula of industrial ceramic, consisting mainly of Zn, Fe and Cr. The obtained pigments were applied in ceramic glazes to colorimetric and visual analysis, which showed good results with the addition of up to 15% of industrial waste. (author)

Methodology for Extraction of Remaining Sodium of Used Sodium Containers

International Nuclear Information System (INIS)

Jung, Minhwan; Kim, Jongman; Cho, Youngil; Jeong, Jiyoung

2014-01-01

Sodium used as a coolant in the SFR (Sodium-cooled Fast Reactor) reacts easily with most elements due to its high reactivity. If sodium at high temperature leaks outside of a system boundary and makes contact with oxygen, it starts to burn and toxic aerosols are produced. In addition, it generates flammable hydrogen gas through a reaction with water. Hydrogen gas can be explosive within the range of 4.75 vol%. Therefore, the sodium should be handled carefully in accordance with standard procedures even though there is a small amount of target sodium remainings inside the containers and drums used for experiment. After the experiment, all sodium experimental apparatuses should be dismantled carefully through a series of draining, residual sodium extraction, and cleaning if they are no longer reused. In this work, a system for the extraction of the remaining sodium of used sodium drums has been developed and an operation procedure for the system has been established. In this work, a methodology for the extraction of remaining sodium out of the used sodium container has been developed as one of the sodium facility maintenance works. The sodium extraction system for remaining sodium of the used drums was designed and tested successfully. This work will contribute to an establishment of sodium handling technology for PGSFR. (Prototype Gen-IV Sodium-cooled Fast Reactor)

Assessment of major technical hazards in the insurance business

International Nuclear Information System (INIS)

Huppmann, H.

1981-01-01

Major technical hazards are covered by means of demand premium rates and subjective corrections according to the degree of innovation and different environmental impacts. The insurer compensates remaining risks by compensatory payments or he moderates them at least in their effects. (DG) [de

Analysis Method for Pesticides Residues by GC/MS in Lebanese Apple

International Nuclear Information System (INIS)

Jaber, F.; Al Iskandarani, M.

2008-01-01

The apple's crop can be affected by many pests during the growing season, which requires careful monitoring. Both apple fruit and apple tree need to be treated by pesticides in order to protect them from pests. Such treatment often leads to the accumulation of stable pesticides inside the fruit. The local market provides a large variety of pesticides allowing farmers to use more than one active substance in order to protect their crop, often without proper advice. Monitoring pesticides on apples and other agricultural crops is the best way to protect consumers health from the hazards of pesticides residues. The development of new, rapid and effective method to analyze the multi pesticides residues at trace levels in apple samples is essential. This work describes the extraction procedure and the analytical method developed to detect the pesticide residues using the gas-chromatographic-mass spectrometric approach (GC-MS). The developed method was successfully applied to analyze apple samples collected from different Lebanese markets for a one year period in order to monitor the presence of pesticides and their stability in apple fruits during storage. (author)

Pesticides residue levels in selected fruits from some Ghanaian markets

International Nuclear Information System (INIS)

Bempah, K.C.

2009-02-01

The amount of some pesticide residues in fruits was monitored at five (5) Accra Metropolis markets. Locally produced fruits (pawpaw and tomato) and imported apples were purchased from two supermarkets and three urban markets in Accra metropolis and analyzed by gas chromatography equipped with electron capture detector for pesticide residues. A total of 220 samples of fruits were extracted and analyzed for pesticide residues, mainly organochlorines (γ-HCH, δ-HCH, aldrin, heptachlor, γ-chlordane, heptachlor epoxide, α-endosulfan, p,p'-DDE, endrin, β-endosulfan, o,p'-DDT, endrin aldehyde, p,p'- DDT, endrin ketone and methoxychlor). The data showed that most of the fruit samples analyzed contain residues of the monitored pesticides above the accepted maximum residue limit (MRL) as adopted by the FAO/WHO Codex Alimentarius Commission (CAC). The results obtained showed that 38.6 % fruit samples showed results above the MRL, 48.7 % were below the MRL and 12.7 % contained no detectable level of the monitored pesticides. Data analysis of health risk estimates indicated that, particularly γ-HCH, δ-HCH, o,p'-DDT, p,p'-DDE or p,p'-DDT do not pose a direct hazard to human health, although present in the three fruits (pawpaw, tomato and apple). However, heptachlor, heptachlor epoxide, endrin aldehyde, and endrin ketone levels exceeded the reference dose, indicating a great potential for systemic toxicity, especially in children who are considered to be the most vulnerable population subgroup. Lastly, the public is aware of pesticide residues in fruits and advocates for the curtailing of pesticide use on horticulture produce or strong educational programmes for farmers on control and safer use of pesticides. (au)

40 CFR 261.5 - Special requirements for hazardous waste generated by conditionally exempt small quantity...

Science.gov (United States)

2010-07-01

...(e). (2) A total of 100 kilograms of any residue or contaminated soil, waste, or other debris... accumulation, only in an on-site process subject to regulation under 40 CFR 261.6(c)(2); or (4) Is used oil... waste, so long as the hazardous waste that is treated was counted once; or (3) Spent materials that are...

Hazard interactions and interaction networks (cascades) within multi-hazard methodologies

Science.gov (United States)

Gill, Joel C.; Malamud, Bruce D.

2016-08-01

This paper combines research and commentary to reinforce the importance of integrating hazard interactions and interaction networks (cascades) into multi-hazard methodologies. We present a synthesis of the differences between multi-layer single-hazard approaches and multi-hazard approaches that integrate such interactions. This synthesis suggests that ignoring interactions between important environmental and anthropogenic processes could distort management priorities, increase vulnerability to other spatially relevant hazards or underestimate disaster risk. In this paper we proceed to present an enhanced multi-hazard framework through the following steps: (i) description and definition of three groups (natural hazards, anthropogenic processes and technological hazards/disasters) as relevant components of a multi-hazard environment, (ii) outlining of three types of interaction relationship (triggering, increased probability, and catalysis/impedance), and (iii) assessment of the importance of networks of interactions (cascades) through case study examples (based on the literature, field observations and semi-structured interviews). We further propose two visualisation frameworks to represent these networks of interactions: hazard interaction matrices and hazard/process flow diagrams. Our approach reinforces the importance of integrating interactions between different aspects of the Earth system, together with human activity, into enhanced multi-hazard methodologies. Multi-hazard approaches support the holistic assessment of hazard potential and consequently disaster risk. We conclude by describing three ways by which understanding networks of interactions contributes to the theoretical and practical understanding of hazards, disaster risk reduction and Earth system management. Understanding interactions and interaction networks helps us to better (i) model the observed reality of disaster events, (ii) constrain potential changes in physical and social vulnerability

The prospect of hazardous sludge reduction through gasification process

Science.gov (United States)

Hakiki, R.; Wikaningrum, T.; Kurniawan, T.

2018-01-01

Biological sludge generated from centralized industrial WWTP is classified as toxic and hazardous waste based on the Indonesian’s Government Regulation No. 101/2014. The amount of mass and volume of sludge produced have an impact in the cost to manage or to dispose. The main objective of this study is to identify the opportunity of gasification technology which can be applied to reduce hazardous sludge quantity before sending to the final disposal. This preliminary study covers the technical and economic assessment of the application of gasification process, which was a combination of lab-scale experimental results and assumptions based on prior research. The results showed that the process was quite effective in reducing the amount and volume of hazardous sludge which results in reducing the disposal costs without causing negative impact on the environment. The reduced mass are moisture and volatile carbon which are decomposed, while residues are fix carbon and other minerals which are not decomposed by thermal process. The economical simulation showed that the project will achieve payback period in 2.5 years, IRR value of 53 % and BC Ratio of 2.3. The further study in the pilot scale to obtain the more accurate design and calculations is recommended.

Distribution of 19 organochlorinated pesticides residues in ginseng ...

African Journals Online (AJOL)

The organochlorinated pesticides widely applied and still remains in soils, has become toxic to ginseng production in Jilin Province. In this study, 19 trace organochlorinated pesticide residues in five types of ginseng products and soil samples from four ginseng production areas were analyzed using a gas ...

Use of fly ash, phosphogypsum and red mud as a liner material for the disposal of hazardous zinc leach residue waste.

Science.gov (United States)

Coruh, Semra; Ergun, Osman Nuri

2010-01-15

Increasing amounts of residues and waste materials coming from industrial activities in different processes have become an increasingly urgent problem for the future. The release of large quantities of heavy metals into the environment has resulted in a number of environmental problems. The present study investigated the safe disposal of the zinc leach residue waste using industrial residues such as fly ash, phosphogypsum and red mud. In the study, leachability of heavy metals from the zinc leach residue has been evaluated by mine water leaching procedure (MWLP) and toxicity characteristic leaching procedure (TCLP). Zinc removal from leachate was studied using fly ash, phosphogypsum and red mud. The adsorption capacities and adsorption efficiencies were determined. The adsorption rate data was analyzed according to the pseudo-second-order kinetic, Elovich kinetic and intra-particle diffusion kinetic models. The pseudo-second-order kinetic was the best fit kinetic model for the experimental data. The results show that addition of fly ash, phosphogypsum and red mud to the zinc leach residue drastically reduces the heavy metal content in the leachate and could be used as liner materials.

Landslides Zonation Hazard: relation between geological structures and landslides occurrence in hilly tropical regions of Brazil

Directory of Open Access Journals (Sweden)

RODRIGO I. CERRI

2017-08-01

Full Text Available ABSTRACT This paper presents a new approach of landslides zonation hazard studies, based on an integrated study of structural data along with geomorphological and external factors, in a hilly regions of Brazil, covered by a tropical humid rain-forest, called Serra do Mar. The Serra do Mar consists of a hilly region along the east coast of Brazil, with high slopes and many geological structures in a gneiss - migmatitic terrain. In contrast to traditional approaches, this method proposes that structural data (foliation, fractures and bedding planes and its relation with the slope geometry, is important to be consider in the landslide zonation hazard, along with declivity, relative relief, soil and rock properties, land use and vegetation cover and hydrogeological and climate factors. Results show that slopes with high hazard have the same dip direction of geological structures. Landslide zonation hazard using structural data contributes to a better understanding of how these structures, preserved in tropical residual soils, influence on slope stability and generates landslides.

Landslides Zonation Hazard: relation between geological structures and landslides occurrence in hilly tropical regions of Brazil.

Science.gov (United States)

Cerri, Rodrigo I; Reis, Fábio A G V; Gramani, Marcelo F; Giordano, Lucilia C; Zaine, José Eduardo

2017-01-01

This paper presents a new approach of landslides zonation hazard studies, based on an integrated study of structural data along with geomorphological and external factors, in a hilly regions of Brazil, covered by a tropical humid rain-forest, called Serra do Mar. The Serra do Mar consists of a hilly region along the east coast of Brazil, with high slopes and many geological structures in a gneiss - migmatitic terrain. In contrast to traditional approaches, this method proposes that structural data (foliation, fractures and bedding planes) and its relation with the slope geometry, is important to be consider in the landslide zonation hazard, along with declivity, relative relief, soil and rock properties, land use and vegetation cover and hydrogeological and climate factors. Results show that slopes with high hazard have the same dip direction of geological structures. Landslide zonation hazard using structural data contributes to a better understanding of how these structures, preserved in tropical residual soils, influence on slope stability and generates landslides.

Prediction of the residual strength of clay using functional networks

Directory of Open Access Journals (Sweden)

S.Z. Khan

2016-01-01

Full Text Available Landslides are common natural hazards occurring in most parts of the world and have considerable adverse economic effects. Residual shear strength of clay is one of the most important factors in the determination of stability of slopes or landslides. This effect is more pronounced in sensitive clays which show large changes in shear strength from peak to residual states. This study analyses the prediction of the residual strength of clay based on a new prediction model, functional networks (FN using data available in the literature. The performance of FN was compared with support vector machine (SVM and artificial neural network (ANN based on statistical parameters like correlation coefficient (R, Nash--Sutcliff coefficient of efficiency (E, absolute average error (AAE, maximum average error (MAE and root mean square error (RMSE. Based on R and E parameters, FN is found to be a better prediction tool than ANN for the given data. However, the R and E values for FN are less than SVM. A prediction equation is presented that can be used by practicing geotechnical engineers. A sensitivity analysis is carried out to ascertain the importance of various inputs in the prediction of the output.

Protein structure based prediction of catalytic residues.

Science.gov (United States)

Fajardo, J Eduardo; Fiser, Andras

2013-02-22

Worldwide structural genomics projects continue to release new protein structures at an unprecedented pace, so far nearly 6000, but only about 60% of these proteins have any sort of functional annotation. We explored a range of features that can be used for the prediction of functional residues given a known three-dimensional structure. These features include various centrality measures of nodes in graphs of interacting residues: closeness, betweenness and page-rank centrality. We also analyzed the distance of functional amino acids to the general center of mass (GCM) of the structure, relative solvent accessibility (RSA), and the use of relative entropy as a measure of sequence conservation. From the selected features, neural networks were trained to identify catalytic residues. We found that using distance to the GCM together with amino acid type provide a good discriminant function, when combined independently with sequence conservation. Using an independent test set of 29 annotated protein structures, the method returned 411 of the initial 9262 residues as the most likely to be involved in function. The output 411 residues contain 70 of the annotated 111 catalytic residues. This represents an approximately 14-fold enrichment of catalytic residues on the entire input set (corresponding to a sensitivity of 63% and a precision of 17%), a performance competitive with that of other state-of-the-art methods. We found that several of the graph based measures utilize the same underlying feature of protein structures, which can be simply and more effectively captured with the distance to GCM definition. This also has the added the advantage of simplicity and easy implementation. Meanwhile sequence conservation remains by far the most influential feature in identifying functional residues. We also found that due the rapid changes in size and composition of sequence databases, conservation calculations must be recalibrated for specific reference databases.

Effect of cooking on enrofloxacin residues in chicken tissue.

Science.gov (United States)

Lolo, M; Pedreira, S; Miranda, J M; Vázquez, B I; Franco, C M; Cepeda, A; Fente, C

2006-10-01

The aim of this study was to determine the effect of different cooking processes (microwaving, roasting, boiling, grilling and frying) on naturally incurred enrofloxacin residues in chicken muscle. Enrofloxacin and its metabolite, ciprofloxacin, were analysed using a validated LC-MS method with limits of detection (LOD) and quantification (LOQ), respectively, of 2 and 5 ng g-1 quinolones in muscle samples. The method was shown to be linear over the range 5-500 ng g-1. Mean intra-day relative standard deviation (RSD) at a concentration of 50 ng g-1 (n = 6) was 6%; inter-day RSD was 12%. A recovery study demonstrated that 65-101%, of the drug and metabolite could be recovered from the tissue. The RSD with naturally incurred roasted chicken breast was 9.18% at a concentration of 11 +/- 1.01 ng g-1 (n = 6). In water, enrofloxacin remained stable for 3 h when heated at 100 degrees C. It was concluded that residue data from raw tissue are valid for estimation of consumer exposure to this drug, as well as the ADI calculations because cooking procedures did not affect enrofloxacin residues, which remained stable during heating. However, there was an apparent decrease in quinolone concentration in tissue because some was lost by exudation into the liquid used for cooking. Conversely, for a cooking procedure with water loss, there was an apparent increase in residue concentration.

Biosorbents for Removing Hazardous Metals and Metalloids †

Science.gov (United States)

Inoue, Katsutoshi; Parajuli, Durga; Ghimire, Kedar Nath; Biswas, Biplob Kumar; Kawakita, Hidetaka; Oshima, Tatsuya; Ohto, Keisuke

2017-01-01

Biosorbents for remediating aquatic environmental media polluted with hazardous heavy metals and metalloids such as Pb(II), Cr(VI), Sb(III and V), and As(III and V) were prepared from lignin waste, orange and apple juice residues, seaweed and persimmon and grape wastes using simple and cheap methods. A lignophenol gel such as lignocatechol gel was prepared by immobilizing the catechol functional groups onto lignin from sawdust, while lignosulfonate gel was prepared directly from waste liquor generated during pulp production. These gels effectively removed Pb(II). Orange and apple juice residues, which are rich in pectic acid, were easily converted using alkali (e.g., calcium hydroxide) into biosorbents that effectively removed Pb(II). These materials also effectively removed Sb(III and V) and As(III and V) when these were preloaded with multi-valent metal ions such as Zr(IV) and Fe(III). Similar biosorbents were prepared from seaweed waste, which is rich in alginic acid. Other biosorbents, which effectively removed Cr(VI), were prepared by simply treating persimmon and grape wastes with concentrated sulfuric acid. PMID:28773217

Peptides containing internal residues of pyroglutamic acid: proton NMR characteristics

International Nuclear Information System (INIS)

Khan, S.A.

1986-01-01

The proton NMR characteristics of internal pyroglutamic acid (Glp; 5-oxoproline) residues in seven tripeptides of the general structure Boc-Xxx-Glp-Yyy-NH 2 were studied. In general, the chemical shifts of several diagnostic protons moved downfield on going from the Glu-containing peptides (Boc-Xxx-Glu-Yyy-NH 2 ) to the corresponding Glp-containing peptides. The C-2 proton of the Xxx residue was shifted by about 1.1 ppm. The N-2 proton of the Yyy residue was shifted by about 0.5 ppm. The C-2 proton of the Glx residue itself was shifted by about 0.5 ppm. One of the Glx C-3 protons was also shifted by about 0.5 ppm, but the other remained essentially unchanged. Finally, the Glx C-4 protons were shifted by about 0.3 ppm. Internal Glu residues are readily converted chemically into internal Glp residues. This conversion also occurs as a side reaction during HP cleavage of the protecting group from Glu(OBzl) residues. The spontaneous fragmentation of serum proteins C3, C4 and λ 2 -macroglobulin under denaturing conditions is probably due to regioselective hydrolysis of an internal Glp residue formed in each of these proteins upon denaturation. These proton NMR characteristics may be useful in establishing the presence of internal Glp residues in synthetic and natural peptides

Remaining Sites Verification Package for the 100-C-9:2 Sanitary Sewer Pipelines. Attachment to Waste Site Reclassification Form 2004-013

International Nuclear Information System (INIS)

Dittmer, L.M.

2007-01-01

The 100-C-9:2 sanitary sewer pipelines include the feeder pipelines associated with the 1607-B8, the 1607-B9, the 1607-B10 and the 1607-B11 septic systems. Contaminated soil and piping from the feeder lines to the septic systems were removed and disposed of. The remaining soil in the excavations has been shown to meet the remedial action objectives specified in the Remaining Sites ROD. The results of verification sampling show that residual contaminant concentrations do not preclude any future uses and allow for unrestricted use of shallow zone soils. The results also demonstrate that residual contaminant concentrations are protective of groundwater and the Columbia River

Remaining Sites Verification Package for the 128-B-3 Burn Pit Site, Waste Site Reclassification Form 2006-058

Energy Technology Data Exchange (ETDEWEB)

L. M. Dittmer

2006-11-17

The 128-B-3 waste site is a former burn and disposal site for the 100-B/C Area, located adjacent to the Columbia River. The 128-B-3 waste site has been remediated to meet the remedial action objectives specified in the Remaining Sites ROD. The results of verification sampling demonstrated that residual contaminant concentrations do not preclude any future uses and allow for unrestricted use of shallow zone soils. The results of sampling at upland areas of the site also showed that residual contaminant concentrations are protective of groundwater and the Columbia River.

Remaining Sites Verification Package for the 100-B-24 Spillway. Attachment to Waste Site Reclassification Form 2006-051

International Nuclear Information System (INIS)

Dittmer, L.M.

2006-01-01

The 100-B-24 Spillway is a spillway that was designed to serve as an emergency discharge point for the 116-B-7 outfall in the event that the 100-B-15 river effluent pipelines were blocked, damaged, or undergoing maintenance. The site meets the remedial action objectives specified in the Remaining Sites ROD. The results of confirmatory sampling show that residual contaminant concentrations do not preclude any future uses and allow for unrestricted use of shallow zone soils. The results also demonstrate that residual contaminant concentrations are protective of groundwater and the Columbia River

Radiological hazard assessment at the Monte Bello Islands

International Nuclear Information System (INIS)

Cooper, M.B.; Martin, L.J.; Wilks, M.J.; Wiliams, G.A.

1990-12-01

Field and laboratory measurements are described and data presented which enabled dose assessments for exposure to artificial radionuclides at the Monte Bello Islands, the sites of U.K. atomic weapons tests in 1952 and 1956. The report focuses on quantifying the inhalation hazard as exposure via the ingestion and wound contamination pathways is considered inconsequential. Surface soil concentrations of radionuclides and particle size analyses are presented for various sampling sites. Analyses of the distribution with depth indicated that, in general, the activity is more or less uniformly mixed through the top 40 mm, although in a few cases the top 10 mm contains the bulk of the activity. The 239 Pu/ 241 Am activity ratios were measured for selected samples. The only potential hazards to health from residual radioactive contamination on the Monte Bello Islands are due to the inhalation of actinides (specifically plutonium and americium) and from the external gamma-radiation field. Only one area, in the fallout plume of HURRICANE to the north-west of Main Beach, is a potential inhalation hazard. For an average inhalable dust loading of 0.1 mg/m 3 , three days occupancy of the most contaminated site will result in a committed effective dose equivalent of 1 mSv. The two ground zeros could not be considered inhalation hazards, considering the small areas concerned and the habits of visitors (full-time occupancy, over a period of one year or more, of the most contaminated sites at either of the G1 or G2 ground zeros would be required to reach 1 mSv). 25 refs., 23 tabs., 3 figs

Research items regarding seismic residual risk evaluation

Energy Technology Data Exchange (ETDEWEB)

NONE

2013-08-15

After learning the Fukushima Dai-ichi NPP severe accidents in 2011, the government investigation committee proposed the effective use of probabilistic safety assessment (PSA), and now it is required to establish new safety rules reflecting the results of probabilistic risk assessment (PRA) and proposed severe accident measures. Since the Seismic Design Guide has been revised on September 19, 2006, JNES has been discussing seismic PRA (Levels 1-3) methods to review licensees' residual risk assessment while preparing seismic PRA models. Meanwhile, new safety standards for light water reactors are to be issued and enforced on July 2013, which require the residual risk of tsunami, in addition to earthquakes, should be lowered as much as possible. The Fukushima accidents raised the problems related to risk assessment, e.g. approaches based on multi-hazard (earthquake and tsunami), multi-unit, multi-site, and equipment's common cause failure. This fiscal year, while performing seismic and/or tsunami PRA to work on these problems, JNES picked up the equipment whose failure greatly contribute to core damage, surveyed accident management measures on those equipment as well as effectiveness to reduce core damage probability. (author)

THE METHOD OF ASSESSING ROCK BURSTING HAZARD IN MINING

Directory of Open Access Journals (Sweden)

Anna MANOWSKA

2015-04-01

Full Text Available The article discusses a concept of forecasting accident risk during longwall extraction in crump-risk conditions. In Polish mines rock burst hazard can be described as high compared to other mines around the world. It's related to increase of depth of longwall field operation, preparation works, including drilling of mine face pavements which leads to systematic deterioration of geological and mining conditions. Depletion of coal is also the reason why mines operate in high mining tremor risk conditions. Mines more and more often operate in decks, where there is large number of edges and remains of older decks. Rocks bursts still remain one of the most dangerous natural hazards and therefore are fundamental prob-lem and have the greatest impact on safety in mining industry. The proposed method for forecasting accidents and loss-es in people and goods can contribute to improvement of work organization methods and mine safety management system.

Property-close source separation of hazardous waste and waste electrical and electronic equipment - A Swedish case study

International Nuclear Information System (INIS)

Bernstad, Anna; Cour Jansen, Jes la; Aspegren, Henrik

2011-01-01

Through an agreement with EEE producers, Swedish municipalities are responsible for collection of hazardous waste and waste electrical and electronic equipment (WEEE). In most Swedish municipalities, collection of these waste fractions is concentrated to waste recycling centres where households can source-separate and deposit hazardous waste and WEEE free of charge. However, the centres are often located on the outskirts of city centres and cars are needed in order to use the facilities in most cases. A full-scale experiment was performed in a residential area in southern Sweden to evaluate effects of a system for property-close source separation of hazardous waste and WEEE. After the system was introduced, results show a clear reduction in the amount of hazardous waste and WEEE disposed of incorrectly amongst residual waste or dry recyclables. The systems resulted in a source separation ratio of 70 wt% for hazardous waste and 76 wt% in the case of WEEE. Results show that households in the study area were willing to increase source separation of hazardous waste and WEEE when accessibility was improved and that this and similar collection systems can play an important role in building up increasingly sustainable solid waste management systems.

Residues of PCDDs and PCDFs in human milk samples in Ahmedabad, India

Energy Technology Data Exchange (ETDEWEB)

Kashyap, R.; Bhatnagar, V.; Sadhu, H.; Jhamb, N.; Karanjkar, R.; Saiyed, H. [National Inst. of Occupational Health, Ahmedabad (India)

2004-09-15

Polychlorinated dibenzo-p-dioxins (PCDDs) and Polychlorinated dibenzo furans (PCDFs) represent a class of organic environmental pollutants. They are unwanted byproduct of incineration, uncontrolled burning and certain industrial processes. They are persistent in nature and bioaccumulates through food chain. These are hazardous to human health and environment. The residues of these toxicants have been detected in human adipose tissue, blood and milk. WHO has coordinated two rounds of follow up studies on levels of PCDD/Fs and PCBs in human milk and the data shows a decreasing trend during the last 30 years. However, in India there is no data available on the exposure and residues of these contaminants. This study presents first time the levels of dioxin and furans in human milk samples collected from the Ahmedabad city in India.

Report 5: Guidance document. Implementation of biological infestation hazards in extended PSA

International Nuclear Information System (INIS)

Hasnaoui, C.; Georgescu, G.; Joel, P.; Sperbeck, S.; Kollasko, H.; Kumar, M.

2016-01-01

This report covers the assessment of biological hazards with PSA. It provides an overview of the available data and available practices in modelling this type of hazard. First researches in the national and international literature regarding PSA for external and internal hazards shows that probabilistic analyses were very rarely carried out in order to quantify the risk induced by biological hazards. Nevertheless, Section 3 provides some data from some countries. History has shown that this hazard can happened and can be highly safety significant. Screening out this event must be done with great care. The overall analysis approach for Level 1 PSA for internal events can be used for the biological hazards with some care to take into impact the nature of the hazard as it impacts many systems at different times and duration. A proposed detailed methodology is described in Section 4. Still some open issues remain: the methodology must also consider event combination of biological infestation with other external hazards wind or flooding or rainfall and multi-units impact. These aspects present still a lot of challenges to PSA developers. The ASAMPSA-E report recommends that further emphasis shall be put on these two aspects of PSA modelling: multi-units site impact and hazards combinations. (authors)

Residual stresses in weld-clad reactor pressure vessel steel

International Nuclear Information System (INIS)

Bertram, W.

1975-01-01

Cladding of low alloy nuclear reactor pressure vessel steel with austenitic stainless steel introduces in heavy section components high residual stresses which may cause microcrack formation in stress relief heat treatment. In this investigation an attempt is made to contribute to the solution of the stress relief cracking problem by determining quantitatively the magnitude and distribution of the residual stresses after cladding and after subsequent stress relief heat treatment. The distribution of residual stresses was determined on the basis of a combined experimental-mathematical procedure. Heavy section plate specimens of low alloy steel as base material were given an austenitic monolayer-cladding using the techniques of strip electrode and plasma hot wire cladding, respectively. A number of plates was stress relief heat treated. Starting from the cladded surface the thickness of the plates was reduced by subsequent removal of layers of material. The elastic strain reaction to the removal of each layer was measured by strain gauges. From the data obtained the biaxial residual stress distribution was computed as a function of thickness using relations which are derived for this particular case. In summary, lower residual stresses are caused by reduced thickness of the components. As the heat input, is decreased at identical base material thickness, the residual stresses are lowered also. The height of the tensile residual stress peak, however, remains approximataly constant. In stress relief annealed condition the residual stresses in the cladding are in tension; in the base material the residual stresses are negligibly small

Hydrodesulfurization and hydrodemetallization of different origin vacuum residues : new modeling approach.

OpenAIRE

Ferreira , Cristina; Tayakout-Fayolle , Melaz; Guibard , Isabelle; Lemos , Francisco

2014-01-01

International audience; In order to be able to upgrade the heaviest part of the crude oil one needs to remove several impurities, such as sulfur or metals. Residue hydrotreatment in fixed beds, under high hydrogen pressure can achieve high removal performances, with an industrial catalysts optimized staging. Despite the recent improvements, petroleum residues remain very difficult to describe and characterize in detail. Several kinetic models have been developed, but mostly they are feed depe...

Residual stress measurement of large scaled welded pipe using neutron diffraction method. Effect of SCC crack propagation and repair weld on residual stress distribution

International Nuclear Information System (INIS)

Suzuki, Hiroshi; Katsuyama, Jinya; Tobita, Tohru; Morii, Yukio

2011-01-01

The RESA-1 neutron engineering diffractometer in the JRR-3 (Japan Research Reactor No.3) at the Japan Atomic Energy Agency, which is used for stress measurements, was upgraded to realize residual stress measurements of large scaled mechanical components. A series of residual stress measurements was made to obtain through-thickness residual stress distributions in a Type 304 stainless steel butt-welded pipe of 500A-sch.80 using the upgraded RESA-1 diffractometer. We evaluated effects of crack propagation such as stress corrosion cracking (SCC) and a part-circumference repair weld on the residual stress distributions induced by girth welding. Measured residual stress distributions near original girth weld revealed good agreement with typical results shown in some previous works using finite element method, deep hole drilling as well as neutron diffraction. After introducing a mock crack with 10 mm depth in the heat affected zone on the inside wall of the pipe by electro discharge machining, the axial residual stresses were found to be released in the part of the mock crack. However, changes in the through-wall bending stress component and the self-equilibrated stress component were negligible and hence the axial residual stress distribution in the ligament was remained in the original residual stresses near girth weld without the mock crack. Furthermore, changes in hoop and radial residual stress were also small. The residual stress distributions after a part repair welding on the outer circumference of the girth weld were significantly different from residual stress distributions near the original girth weld. The through-thickness average axial residual stress was increased due to increase of the tensile membrane stress and mitigation of the bending stress after repair welding. Throughout above studies, we evidenced that the neutron diffraction technique is useful and powerful tool for measuring residual stress distributions in large as well as thick mechanical

Fluoroquinolone residues in raw meat from open markets in Ibadan, Southwest, Nigeria

Directory of Open Access Journals (Sweden)

Adekunbi Bridget Omotoso

2015-07-01

Full Text Available Misuse of fluoroquinolones in livestock production may lead to the presence of their residues in tissues of meat animals after slaughter, constituting health hazards to consumers. The present study was designed to screen for residues of three fluoroquinolones (ciprofloxacin, norfloxacin and ofloxacin in raw meat. Microbiological assay, followed by High Performance Liquid Chromatography (HPLC was used to screen three hundred and twenty samples of beef, chicken, pork and chevon purchased from open markets. Initial screening by microbiological assay revealed that 50%, 55%, 40% and 40% of beef, chicken, pork and chevon, respectively were positive for residues of antibiotics. Further analysis by HPLC with UV detection revealed the presence of ciprofloxacin, norfloxacin and ofloxacin at varying concentrations in the meat samples. Ofloxacin was the least in frequency and abundance in all meat types. Results obtained in this study have implications for public health and will lead to steps that will further enhance the safety of animal foods in order to protect consumers and the animal production industry

Analysis of long-term impacts of TRU waste remaining at generator/storage sites for No Action Alternative 2

International Nuclear Information System (INIS)

Buck, J.W.; Bagaasen, L.M.; Bergeron, M.P.; Streile, G.P.

1997-09-01

This report is a supplement to the Waste Isolation Pilot Plant Disposal-Phase Final Supplemental Environmental Impact Statement (SEIS-II). Described herein are the underlying information, data, and assumptions used to estimate the long-term human-health impacts from exposure to radionuclides and hazardous chemicals in transuranic (TRU) waste remaining at major generator/storage sites after loss of institutional control under No Action Alternative 2. Under No Action Alternative 2, TRU wastes would not be emplaced at the Waste Isolation Pilot Plant (WIPP) but would remain at generator/storage sites in surface or near-surface storage. Waste generated at smaller sites would be consolidated at the major generator/storage sites. Current TRU waste management practices would continue, but newly generated waste would be treated to meet the WIPP waste acceptance criteria. For this alternative, institutional control was assumed to be lost 100 years after the end of the waste generation period, with exposure to radionuclides and hazardous chemicals in the TRU waste possible from direct intrusion and release to the surrounding environment. The potential human-health impacts from exposure to radionuclides and hazardous chemicals in TRU waste were analyzed for two different types of scenarios. Both analyses estimated site-specific, human-health impacts at seven major generator/storage sites: the Hanford Site (Hanford), Idaho National Engineering and Environmental Laboratory (INEEL), Lawrence Livermore National Laboratory (LLNL), Los Alamos National Laboratory (LANL), Oak Ridge National Laboratory (ORNL), Rocky Flats Environmental Technology Site (RFETS), and Savannah River Site (SRS). The analysis focused on these seven sites because 99 % of the estimated TRU waste volume and inventory would remain there under the assumptions of No Action Alternative 2

How to remain nonfolded and pliable: the linkers in modular α-amylases as a case study.

Science.gov (United States)

Feller, Georges; Dehareng, Dominique; Lage, Jean-Luc Da

2011-07-01

The primary structure of linkers in a new class of modular α-amylases constitutes a paradigm of the structural basis that allows a polypeptide to remain nonfolded, extended and pliable. Unfolding is mediated through a depletion of hydrophobic residues and an enrichment of hydrophilic residues, amongst which Ser and Thr are over-represented. An extended and flexible conformation is promoted by the sequential arrangement of Pro and Gly, which are the most abundant residues in these linkers. This is complemented by charge repulsion, charge clustering and disulfide-bridged loops. Molecular dynamics simulations suggest the existence of conformational transitions resulting from a transient and localized hydrophobic collapse, arising from the peculiar composition of the linkers. Accordingly, these linkers should not be regarded as fully disordered, but rather as possessing various discrete structural patterns allowing them to fulfill their biological function as a free energy reservoir for concerted motions between structured domains. © 2011 The Authors Journal compilation © 2011 FEBS.

78 FR 66107 - National Emissions Standards for Hazardous Air Pollutants Residual Risk and Technology Review for...

Science.gov (United States)

2013-11-04

... estimate VCS voluntary consensus standards WWW world wide web Organization of this Document. The... oxidizer RTR residual risk and technology review SAB Science Advisory Board SBA Small Business... acceptable in the world in which we live'' (Risk Report at 178, quoting NRDC v. EPA, 824 F.2d 1146, 1165 (D.C...

Nitrogen recycling from fuel-extracted algal biomass: residuals as the sole nitrogen source for culturing Scenedesmus acutus.

Science.gov (United States)

Gu, Huiya; Nagle, Nick; Pienkos, Philip T; Posewitz, Matthew C

2015-05-01

In this study, the reuse of nitrogen from fuel-extracted algal residues was investigated. The alga Scenedesmus acutus was found to be able to assimilate nitrogen contained in amino acids, yeast extracts, and proteinaceous alga residuals. Moreover, these alternative nitrogen resources could replace nitrate in culturing media. The ability of S. acutus to utilize the nitrogen remaining in processed algal biomass was unique among the promising biofuel strains tested. This alga was leveraged in a recycling approach where nitrogen is recovered from algal biomass residuals that remain after lipids are extracted and carbohydrates are fermented to ethanol. The protein-rich residuals not only provided an effective nitrogen resource, but also contributed to a carbon "heterotrophic boost" in subsequent culturing, improving overall biomass and lipid yields relative to the control medium with only nitrate. Prior treatment of the algal residues with Diaion HP20 resin was required to remove compounds inhibitory to algal growth. Copyright © 2014 Elsevier Ltd. All rights reserved.

Food processing as a means for pesticide residue dissipation

Directory of Open Access Journals (Sweden)

Đorđević Tijana

2016-01-01

Full Text Available Pesticides are one of the major inputs used for increasing agricultural productivity of crops. However, their inadequate application may produce large quantities of residues in the environment and, once the environment is contaminated with pesticides, they may easily enter into the human food chain through plants, creating a potentially serious health hazard. Nowadays, consumers are becoming more aware of the importance of safe and high quality food products. Thus it is pertinent to explore simple, cost-effective strategies for decontaminating food from pesticides. Various food processing techniques, at industrial and/or domestical level, have been found to significantly reduce the contents of pesticide residues in most food materials. The extent of reduction varies with the nature of pesticides, type of commodity and processing steps. Pesticides, especially those with limited movement and penetration ability, can be removed with reasonable efficiency by washing, and the effectiveness of washing depends on pesticide solubility in water or in different chemical solvents. Peeling of fruit and vegetable skin can dislodge pesticide residues to varying degrees, depending on constitution of a commodity, chemical nature of the pesticide and environmental conditions. Different heat treatments (drying, pasteurization, sterilization, blanching, steaming, boiling, cooking, frying or roasting during various food preparation and preservation processes can cause losses of pesticide residues through evaporation, co-distillation and/or thermal degradation. Product manufactures, from the simplest grain milling, through oil extraction and processing, juicing/pureeing or canning of fruits and vegetables, to complex bakery and dairy production, malting and brewing, wine making and various fermentation processes, play a role in the reduction of pesticide contents, whereby each operation involved during processing usually adds to a cumulative effect of reduction of

Approaches for Modelling the Residual Service Life of Marine Concrete Structures

Directory of Open Access Journals (Sweden)

Amir Rahimi

2014-01-01

Full Text Available This paper deals with the service life design of existing reinforced concrete structures in a marine environment. The general procedure of condition assessment for estimating the residual service life of structures before a repair measure is illustrated. For assessment of the residual service life of structures which have undergone a repair measure a simplified mathematical model of chloride diffusion in a 2-layer system is presented. Preliminary probabilistic calculations demonstrate the effect of various conditions on the residual service life. First studies of the chloride diffusion in a 2-layer system have been conducted using the finite element method. Results of a long-term exposure test are presented to illustrate the performance of two different repair materials. The distribution of residual chlorides after application of a repair material is being studied in laboratory investigations. The residual chlorides migrate from the concrete layer into the new layer immediately after the repair material has been applied to the concrete member. The content and gradient of residual chlorides, along with the thickness and the chloride ingress resistance of both the remaining and the new layer of cover, will determine the residual service life of the repaired structures.

Detection of antibiotic residues in food by Charm II test

International Nuclear Information System (INIS)

Addali, Mohamed

2014-01-01

Antibiotics are used in food to: -therapy and prophylaxis, -increase the productivity of the food producing animals. The presence of antimicrobial residues: -constitutes a potential human health hazard. has significant impact on international food trade. has implications on technological process in dairy industry. Detection of antibiotic residues is of great interest. It helps protect humans against the effects of such residues, the more it can support the participation of our country in international trade. Charm II test is one of the methods of detection of antimicrobial residues. The tests utilize microbial or antibody receptor assay technology. The sample is incubated with a binding agent (microbial cells with specific receptor sites or with specific antibodies attached) and a tracer (the radio-labeled version of the antibiotic to be detected). The amount of tracer on the binding agent is measured using a scintillation counter and is compared to a pre-determined cut-off or control point. If contaminating antibiotic is present, it will prevent the binding of the tracer by occupying the receptors on the binding agent. The less labeled tracer detected, the more contaminating antibiotic there is present in the sample. This work, carried out at the Radiochemical Laboratory of the National Centre of Nuclear Science and Technology, has two parts: 1/ The first is reserved to a literature review provides an overview on antibiotics and the charm II method. 2/ The second is devoted to the experimental study and presentation of results.

Monitoring pesticides residues and contaminants for some leafy vegetables at the market level

International Nuclear Information System (INIS)

Ibrahim, A. B. H.

2004-03-01

Pesticide residues and contaminants in selected leafy vegetables, namely (lettuce, garden rocket and salad onion) were monitored at market level in Riyadh City in Saudi Arabia, during the period june to july 2001. Fifteen samples of vegetables from the City vegetable market of Riyadh were collected and subjected to multi-pesticide residue detection and analysis by gas chromatography with mass spectrometer and electron capture detectors (GC/MS,ECD). Results of sample extracts analysis showed that the two vegetables of: garden rocket and salad onion contain pesticide residues and contaminants which have no Maximum Residue Limits (MRL) prescribed by Codex Alimentarius Commission (CAC) collaborate with World Health and Food and Agriculture Organizations (WHO/FAO). Whereas lettuce vegetable was found free of any identified pesticide residues or contaminants. Garden rocket was shown to contain dibutyl phthalate (0.04 ppm)-steryl chloride (0.02 ppm) tridecane (0.06 ppm)-hexadecane (0.07 ppm)-BIS (ethylhexyl) phthalate (0.006 ppm) and pyridinium, 1-hexyl chloride (0.01 ppm). The salad onion was found to contain 9-octadecanamide (0.13 ppm)-tridecane (0.15 ppm) and tetradecane (0.16 ppm). There are no established MRL s for these pesticides and contaminants detected in garden rocket and salad onion, although when impacts on human health were reviewed some of them were found probably hazardous. (Author)

Evaluation of the effectiveness of olive cake residue as an expansive soil stabilizer

Science.gov (United States)

Nalbantoglu, Zalihe; Tawfiq, Salma

2006-08-01

The quantity of the by-product olive cake residue generated in most parts of the Mediterranean countries continues to increase and expected to double in amount within 10 15 years. This increase intensifies the problems associated with the disposal of this by-product. Olive cake residue has a potential for use as a soil stabilizer and large volumes can be beneficially used. This study is directed toward determining if olive cake residue can be utilized to increase the strength and stability of expansive soils which constitute a costly natural hazard to lightweight structures on shallow foundations. A series of laboratory tests using engineering properties, such as Atterberg limits, moisture-density relationship (compaction), swell, unconfined compressive strength were undertaken to evaluate the effectiveness and performance of the olive cake residue as a soil stabilizer. Test results indicate that an addition of only 3% burned olive waste into the soil causes a reduction in plasticity, volume change and an increase in the unconfined compressive strength. However, it was observed that the presence of burned olive waste in the soil greater than 3% caused an increase in the compressibility and a decrease in the unconfined compressive strength. Test results indicate that the use of olive waste in soil stabilization gives greater benefits to the environment than simply disposing of the by-product, olive cake residue.

GO/NO-GO - When is medical hazard mitigation acceptable for launch?

Science.gov (United States)

Hamilton, Douglas R.; Polk, James D.

2005-01-01

Medical support of spaceflight missions is composed of complex tasks and decisions that dedicated to maintaining the health and performance of the crew and the completion of mission objectives. Spacecraft represent one of the most complex vehicles built by humans, and are built to very rigorous design specifications. In the course of a Flight Readiness Review (FRR) or a mission itself, the flight surgeon must be able to understand the impact of hazards and risks that may not be completely mitigated by design alone. Some hazards are not mitigated because they are never actually identified. When a hazard is identified, it must be reduced or waivered. Hazards that cannot be designed out of the vehicle or mission, are usually mitigated through other means to bring the residual risk to an acceptable level. This is possible in most engineered systems because failure modes are usually predictable and analysis can include taking these systems to failure. Medical support of space missions is complicated by the inability of flight surgeons to provide "exact" hazard and risk numbers to the NASA engineering community. Taking humans to failure is not an option. Furthermore, medical dogma is mostly comprised of "medical prevention" strategies that mitigate risk by examining the behaviour of a cohort of humans similar to astronauts. Unfortunately, this approach does not lend itself well for predicting the effect of a hazard in the unique environment of space. This presentation will discuss how Medical Operations uses an evidence-based approach to decide if hazard mitigation strategies are adequate to reduce mission risk to acceptable levels. Case studies to be discussed will include: 1. Risk of electrocution risk during EVA 2. Risk of cardiac event risk during long and short duration missions 3. Degraded cabin environmental monitoring on the ISS. Learning Objectives 1.) The audience will understand the challenges of mitigating medical risk caused by nominal and off

Hazards and hazard combinations relevant for the safety of nuclear power plants

Science.gov (United States)

Decker, Kurt; Brinkman, Hans; Raimond, Emmanuel

2017-04-01

The potential of the contemporaneous impact of different, yet causally related, hazardous events and event cascades on nuclear power plants is a major contributor to the overall risk of nuclear installations. In the aftermath of the Fukushima accident, which was caused by a combination of severe ground shaking by an earthquake, an earthquake-triggered tsunami and the disruption of the plants from the electrical grid by a seismically induced landslide, hazard combinations and hazard cascades moved into the focus of nuclear safety research. We therefore developed an exhaustive list of external hazards and hazard combinations which pose potential threats to nuclear installations in the framework of the European project ASAMPSAE (Advanced Safety Assessment: Extended PSA). The project gathers 31 partners from Europe, North Amerika and Japan. The list comprises of exhaustive lists of natural hazards, external man-made hazards, and a cross-correlation matrix of these hazards. The hazard list is regarded comprehensive by including all types of hazards that were previously cited in documents by IAEA, the Western European Nuclear Regulators Association (WENRA), and others. 73 natural hazards and 24 man-made external hazards are included. Natural hazards are grouped into seismotectonic hazards, flooding and hydrological hazards, extreme values of meteorological phenomena, rare meteorological phenomena, biological hazards / infestation, geological hazards, and forest fire / wild fire. The list of external man-made hazards includes industry accidents, military accidents, transportation accidents, pipeline accidents and other man-made external events. The large number of different hazards results in the extremely large number of 5.151 theoretically possible hazard combinations (not considering hazard cascades). In principle all of these combinations are possible to occur by random coincidence except for 82 hazard combinations that - depending on the time scale - are mutually

Hazardous Waste

Science.gov (United States)

... chemicals can still harm human health and the environment. When you throw these substances away, they become hazardous waste. Some hazardous wastes come from products in our homes. Our garbage can include such hazardous wastes as old batteries, bug spray cans and paint thinner. U.S. residents ...

Improving residue-residue contact prediction via low-rank and sparse decomposition of residue correlation matrix.

Science.gov (United States)

Zhang, Haicang; Gao, Yujuan; Deng, Minghua; Wang, Chao; Zhu, Jianwei; Li, Shuai Cheng; Zheng, Wei-Mou; Bu, Dongbo

2016-03-25

Strategies for correlation analysis in protein contact prediction often encounter two challenges, namely, the indirect coupling among residues, and the background correlations mainly caused by phylogenetic biases. While various studies have been conducted on how to disentangle indirect coupling, the removal of background correlations still remains unresolved. Here, we present an approach for removing background correlations via low-rank and sparse decomposition (LRS) of a residue correlation matrix. The correlation matrix can be constructed using either local inference strategies (e.g., mutual information, or MI) or global inference strategies (e.g., direct coupling analysis, or DCA). In our approach, a correlation matrix was decomposed into two components, i.e., a low-rank component representing background correlations, and a sparse component representing true correlations. Finally the residue contacts were inferred from the sparse component of correlation matrix. We trained our LRS-based method on the PSICOV dataset, and tested it on both GREMLIN and CASP11 datasets. Our experimental results suggested that LRS significantly improves the contact prediction precision. For example, when equipped with the LRS technique, the prediction precision of MI and mfDCA increased from 0.25 to 0.67 and from 0.58 to 0.70, respectively (Top L/10 predicted contacts, sequence separation: 5 AA, dataset: GREMLIN). In addition, our LRS technique also consistently outperforms the popular denoising technique APC (average product correction), on both local (MI_LRS: 0.67 vs MI_APC: 0.34) and global measures (mfDCA_LRS: 0.70 vs mfDCA_APC: 0.67). Interestingly, we found out that when equipped with our LRS technique, local inference strategies performed in a comparable manner to that of global inference strategies, implying that the application of LRS technique narrowed down the performance gap between local and global inference strategies. Overall, our LRS technique greatly facilitates

Visualization of residual organic liquid trapped in aquifers

International Nuclear Information System (INIS)

Conrad, S.H.; Wilson, J.L.; Mason, W.R.; Peplinski, W.J.

1992-01-01

Organic liquids that are essentially immiscible with water migrate through the subsurface under the influence of capillary, viscous, and buoyancy forces. These liquids originate from the improper disposal of hazardous wastes, and the spills and leaks of petroleum hydrocarbons and solvents. The flow visualization experiments described in this study examined the migration of organic liquids through the saturated zone of aquifers, with a primary focus on the behavior of the residual organic liquid saturation, referring to that portion of the organic liquid that is trapped by capillary forces. Etched glass micromodels were used to visually observe dynamic multiphase displacement processes in pore networks. The resulting fluid distributions were photographed. Pore and blob casts were produced by a technique in which an organic liquid was solidified in place within a sand column at the conclusion of a displacement. The columns were sectioned and examined under optical and scanning electron microscopes. Photomicrographs of these sections show the morphology of the organic phase and its location within the sand matrix. The photographs from both experimental techniques reveal that in the saturated zone large amounts of residual organic liquid are trapped as isolated blobs of microscopic size. The size, shape, and spatial distribution of these blobs of residual organic liquid affect the dissolution of organic liquid into the water phase and the biotransformation of organic components. These processes are of concern for the prediction of pollution migration and the design of aquifer remediation schemes

Hazard perception in traffic. [previously knows as: Hazard perception.

NARCIS (Netherlands)

2008-01-01

Hazard perception is an essential part of the driving task. There are clear indications that insufficient skills in perceiving hazards play an important role in the occurrence of crashes, especially those involving novice drivers. Proper hazard perception not only consists of scanning and perceiving

Residual neurovascular function and retinotopy in a case of hemianopia

DEFF Research Database (Denmark)

Ho, Yi-Ching; Cheze, Amandine; Sitoh, Yih-Yian

2009-01-01

INTRODUCTION: For occipital cortex strokes resulting in vision disorders, questions about the viability of residual visual cortex remain. CLINICAL PICTURE: In a patient with a one-year-old, left, complete, homonymous hemianopia due to a right, posterior cerebral artery, ischaemic infarct, we...

Study of radionuclide leaching from the residues of K Basin sludge dissolution

International Nuclear Information System (INIS)

Bechtold, D.B.

1998-01-01

The sludges remaining in the K Basins after removal of the spent N Reactor nuclear fuel will be conditioned for disposal. After conditioning, an acid-insoluble residue will remain that may require further leaching to properly condition it for disposal. This document presents a literature study to identify and recommend one or more chemical leaching treatments for laboratory testing, based on the likely compositions of the residues. The processes identified are a nitric acid cerate leach, a silver-catalyzed persulfate leach, a nitric hydrofluoric acid leach, an oxalic citric acid reactor decontamination leach, a nitric hydrochloric acid leach, a ammonium fluoride nitrate leach, and a HEOPA formate dehydesulfoxylate leach. All processes except the last two are recommended for testing in that order

Identification of Potential Hazard using Hazard Identification and Risk Assessment

Science.gov (United States)

Sari, R. M.; Syahputri, K.; Rizkya, I.; Siregar, I.

2017-03-01

This research was conducted in the paper production’s company. These Paper products will be used as a cigarette paper. Along in the production’s process, Company provides the machines and equipment that operated by workers. During the operations, all workers may potentially injured. It known as a potential hazard. Hazard identification and risk assessment is one part of a safety and health program in the stage of risk management. This is very important as part of efforts to prevent occupational injuries and diseases resulting from work. This research is experiencing a problem that is not the identification of potential hazards and risks that would be faced by workers during the running production process. The purpose of this study was to identify the potential hazards by using hazard identification and risk assessment methods. Risk assessment is done using severity criteria and the probability of an accident. According to the research there are 23 potential hazard that occurs with varying severity and probability. Then made the determination Risk Assessment Code (RAC) for each potential hazard, and gained 3 extreme risks, 10 high risks, 6 medium risks and 3 low risks. We have successfully identified potential hazard using RAC.

Solid radioactive waste: evaluation of residual activity in nuclear medicine services

International Nuclear Information System (INIS)

Alabarse, Frederico G.; Xavier, Ana M.; Magalhaes, Maisa H.; Guerrero, Jesus S.P.

2009-01-01

An experimental programme to estimate, with a better degree of accuracy, the activity that remains adsorbed in flasks and syringes used in Nuclear Medicine Services for the administration of radionuclides to patients submitted to diagnostic or therapy is been conducted under the coordination of the Radioactive Waste Division of the Brazilian Nuclear Energy Commission, CNEN. The adopted recommendation in Brazil to allow an expedite solid waste management in nuclear medicine facilities, up to the present, is to consider that 2% of the initial activity remains adsorbed in the solid waste, which easily allows the calculation of the storage time to achieve regulatory clearance levels by decay. This research evaluates 17 different kinds of radiopharmaceuticals and three radioisotopes: 99m Tc, 67 Ga and 201 Tl. Results obtained by means of a weighting method to estimate the residual mass in flasks show that the ratio of the mass of the liquid that remains in the solid waste to the mass of the empty flask is constant. This suggests that the residual activity depends on the initial activity concentration of radiopharmaceutical contained in each flask, as assumed by the regulatory body. Additionally, results obtained by determining the remaining activity in flasks, shortly after the injection of its radionuclide contents in patients, indicate that an average value for the residual activity of the order of 10% of the initial activity contained in the flasks or syringes should be adopted to determine the decay storage time before the release of solid waste in the urban conventional land fill disposal system. The 'rule of thumb' of 10 half-lives for storage before clearance is also discussed in the present work. (author)

Residual Prostate Cancer in Patients Treated With Endocrine Therapy With or Without Radical Radiotherapy: A Side Study of the SPCG-7 Randomized Trial

International Nuclear Information System (INIS)

Solberg, Arne; Haugen, Olav A.; Viset, Trond; Bergh, Anders; Tasdemir, Ilker; Ahlgren, Goeran; Widmark, Anders; Angelsen, Anders

2011-01-01

Purpose: The Scandinavian Prostate Cancer Group-7 randomized trial demonstrated a survival benefit of combined endocrine therapy and external-beam radiotherapy over endocrine therapy alone in patients with high-risk prostate cancer. In a subset of the study population, the incidence and clinical implications of residual prostate cancer in posttreatment prostate biopsy specimens was evaluated. Methods and Materials: Biopsy specimens were obtained from 120 of 875 men in the Scandinavian Prostate Cancer Group-7 study. Results: Biopsies were performed at median of 45 months follow-up. In 63 patients receiving endocrine treatment only and 57 patients receiving combined treatment, residual cancer was found in 66% (n = 41) and 22% (n = 12), respectively (p < 0.0001). The vast majority of residual tumors were poorly differentiated (Gleason score ≥8). Endocrine therapy alone was predictive of residual prostate cancer: odds ratio 7.49 (3.18-17.7), p < 0.0001. In patients with positive vs. negative biopsy the incidences of clinical events were as follows: biochemical recurrence 74% vs. 27% (p < 0.0001), local progression 26% vs. 4.7% (p = 0.002), distant recurrence 17% vs. 9.4% (p = 0.27), clinical recurrence 36% vs. 13% (p = 0.006), cancer-specific death 19% vs. 9.7% (p = 0.025). In multivariable analysis, biochemical recurrence was significantly associated with residual cancer: hazard ratio 2.69 (1.45-4.99), p = 0.002, and endocrine therapy alone hazard ratio 3.45 (1.80-6.62), p < 0.0001. Conclusions: Radiotherapy combined with hormones improved local tumor control in comparison with endocrine therapy alone. Residual prostate cancer was significantly associated with serum prostate-specific antigen recurrence, local tumor progression, clinical recurrence, and cancer-specific death in univariable analysis. Residual cancer was predictive of prostate-specific antigen recurrence in multivariable analysis.

Investigation of antibiotic residues in edible tissues of slaughtered broilers in Maragheh abattoir using FPT method (short comunication

Directory of Open Access Journals (Sweden)

Masumeh Abasi

2016-05-01

Full Text Available Antibiotic residues in food stuff and their transmission to the consumers have some consequences such as bacterial resistance, allergic reactions, intoxication, carcinogenic effects and disturbing of intestine natural flora. Among microbiologic methods, four plate test (FPT is used to detect antibiotic residues in food stuff, which performs in four culture media with different pH values and test bacteria. The aim of this study was investigation of antibiotic residues in edible tissues of slaughtered broilers in Maragheh abattoir using FPT method. For this reason, 40 slaughtered broilers carcasses in Maragheh abattoir (from 10 different poultry farms were sampled. The sampling was conducted randomly from breast and leg muscles, gizzard as well as liver of each carcass. According to results of current study, 60% of liver samples, 55% of leg samples, 52.5% of breast samples and 52.5% of gizzard samples contained antibiotic residues. Moreover, the amount of antibiotic residues among different samples did not show statistical significance (p>0.05. The highest occurrence of antibiotic residue was found in two flocks (100% and the lowest occurrence was recorded for another two flocks (0%. According to the health hazard of antibiotic residues in foods, continuous monitoring is recommended for edible tissues of broilers.

Residual stresses

International Nuclear Information System (INIS)

Sahotra, I.M.

2006-01-01

The principal effect of unloading a material strained into the plastic range is to create a permanent set (plastic deformation), which if restricted somehow, gives rise to a system of self-balancing within the same member or reaction balanced by other members of the structure., known as residual stresses. These stresses stay there as locked-in stresses, in the body or a part of it in the absence of any external loading. Residual stresses are induced during hot-rolling and welding differential cooling, cold-forming and extruding: cold straightening and spot heating, fabrication and forced fitting of components constraining the structure to a particular geometry. The areas which cool more quickly develop residual compressive stresses, while the slower cooling areas develop residual tensile stresses, and a self-balancing or reaction balanced system of residual stresses is formed. The phenomenon of residual stresses is the most challenging in its application in surface modification techniques determining endurance mechanism against fracture and fatigue failures. This paper discusses the mechanism of residual stresses, that how the residual stresses are fanned and what their behavior is under the action of external forces. Such as in the case of a circular bar under limit torque, rectangular beam under limt moment, reclaiming of shafts welds and peening etc. (author)

Modeling Residual NAPL in Water-Wet Porous Media

Directory of Open Access Journals (Sweden)

R.J. Lenhard

2002-06-01

Full Text Available A model is outlined that predicts NAPL which is held in pore wedges and as films or lenses on solid and water surfaces and contributes negligibly to NAPL advection. This is conceptually referred to as residual NAPL. Since residual NAPL is immobile, it remains in the vadose zone after all free NAPL has drained. Residual NAPL is very important because it is a long-term source for groundwater contamination. Recent laboratory experiments have demonstrated that current models for predicting subsurface NAPL behavior are inadequate because they do not correctly predict residual NAPL. The main reason for the failure is a deficiency in the current constitutive theories for multiphase flow that are used in numerical simulators. Multiphase constitutive theory governs the relations among relative permeability, saturation, and pressure for fluid systems (i.e., air, NAPL, water. In this paper, we outline a model describing relations between fluid saturations and pressures that can be combined with existing multiphase constitutive theory to predict residual NAPL. We test the revised constitutive theory by applying it to a scenario involving NAPL imbibition and drainage, as well as water imbibition and drainage. The results suggest that the revised constitutive theory is able to predict the distribution of residual NAPL in the vadose zone as a function of saturation-path history. The revised model describing relations between fluid saturation and pressures will help toward developing or improving numerical multiphase flow simulators.

Direct stamping of silver nanoparticles toward residue-free thick electrode

Directory of Open Access Journals (Sweden)

Jiseok Kim, Kevin Wubs, Byeong-Soo Bae and Woo Soo Kim

2012-01-01

Full Text Available Direct stamping of functional materials has been developed for cost-effective and process-effective manufacturing of nano/micro patterns. However, there remain several challenging issues like the perfect removal of the residual layer and realization of high aspect ratio. We have demonstrated facile fabrication of flexible strain sensors that have microscale thick interdigitated capacitors with no residual layer by a simple direct stamping with silver nanoparticles (AgNPs. Polyurethane (PU prepolymer was utilized as an adhesive layer to transfer AgNPs more efficiently during the separation step of the flexible stamp from directly stamped AgNPs. Scanning electron microscopy images and energy dispersive x-ray spectroscopy analysis revealed residue-free transfer of microscale thick interdigitated electrodes onto two different flexible substrates (elastomeric and brittle for the application to highly sensitive strain sensors.

Assessment of long-term pH developments in leachate from waste incineration residues

DEFF Research Database (Denmark)

Astrup, Thomas; Jakobsen, Rasmus; Christensen, Thomas Højlund

2006-01-01

influenced by changes in pH over time. The paper presents an approach for assessing pH changes in leachate from municipal solid waste incineration (MSWI) air-pollution-control (APC) residues. Residue samples were subjected to a stepwise batch extraction method in order to obtain residue samples at a range...... of pH Values (similar to common pH-dependence tests), and then on these samples to determine leaching of alkalinity as well as remaining solid phase alkalinity. On a range of APC residues covering various pretreatment and disposal options, this procedure was used to determine leachable and residual...... alkalinity as a function of pH. Mass balance calculations for typical disposal scenarios were used to provide data on pH as a function of the liquid-to-solid (L/S) ratio in the leaching system. Regardless of residue type and pretreatment, pH was found to stay above 7 for L/S ratios up to about 2000 L kg(-1...

Significance of residual abdominal masses in children with abdominal Burkitt's lymphoma

International Nuclear Information System (INIS)

Karmazyn, B.; Horev, G.; Kornreich, L.; Ash, S.; Goshen, Y.; Yaniv, I.

2001-01-01

Purpose: To evaluate the natural history of children with abdominal Burkitt's lymphoma who had complete clinical remission and residual abdominal mass after treatment. Material and methods: The charts and imaging findings of all children with abdominal Burkitt's lymphoma treated and followed at our medical center between 1988 and 1999 were reviewed for the presence, management, clinical course, and prognosis of residual mass. Results: Only children who achieved complete clinical remission were included. The study group consisted of 33 children (20 boys and 13 girls) aged 2.6-17.6 years (mean 7.2 years). Of these, seven (20.6 %) were found to have a residual abdominal mass. Two underwent second-look operation with no evidence of viable tumor on histology. The remaining five were followed by imaging studies for 2.2-9.1 years (mean 6.1 years); none relapsed. Conclusion: Residual mass is not uncommon in children with abdominal Burkitt's lymphoma. The presence of residual mass in a child with complete clinical remission does not alter the long-term prognosis. Therefore, in children with Burkitt's lymphoma and residual mass with no other signs of disease activity, expectant watching may be appropriate. (orig.)

Recycling of air pollution control residues from municipal solid waste incineration into lightweight aggregates.

Science.gov (United States)

Quina, Margarida J; Bordado, João M; Quinta-Ferreira, Rosa M

2014-02-01

This work focuses on the assessment of technological properties and on the leaching behavior of lightweight aggregates (LWA) produced by incorporating different quantities of air pollution control (APC) residues from municipal solid waste (MSW) incineration. Currently this hazardous waste has been mostly landfilled after stabilization/solidification. The LWA were produced by pelletizing natural clay, APC residues as-received from incineration plant, or after a washing treatment, a small amount of oil and water. The pellets were fired in a laboratory chamber furnace over calcium carbonate. The main technological properties of the LWA were evaluated, mainly concerning morphology, bulk and particle densities, compressive strength, bloating index, water adsorption and porosity. Given that APC residues do not own expansive (bloating) properties, the incorporation into LWA is only possible in moderate quantities, such as 3% as received or 5% after pre-washing treatment. The leaching behavior of heavy metals from sintered LWA using water or acid solutions was investigated, and despite the low acid neutralization capacity of the synthetic aggregates, the released quantities were low over a wide pH range. In conclusion, after a washing pre-treatment and if the percentage of incorporation is low, these residues may be incorporated into LWA. However, the recycling of APC residues from MSW incineration into LWA does not revealed any technical advantage. Copyright © 2013 Elsevier Ltd. All rights reserved.

Effective removal of hazardous trace metals from recovery boiler fly ashes.

Science.gov (United States)

Kinnarinen, Teemu; Golmaei, Mohammad; Jernström, Eeva; Häkkinen, Antti

2018-02-15

The objective of this study is to introduce a treatment sequence enabling straightforward and effective recovery of hazardous trace elements from recovery boiler fly ash (RBFA) by a novel method, and to demonstrate the subsequent removal of Cl and K with the existing crystallization technology. The treatment sequence comprises two stages: dissolution of most other RBFA components than the hazardous trace elements in water in Step 1 of the treatment, and crystallization of the process chemicals in Step 2. Solid-liquid separation has an important role in the treatment, due to the need to separate first the small solid residue containing the trace elements, and to separate the valuable crystals, containing Na and S, from the liquid rich in Cl and K. According to the results, nearly complete recovery of cadmium, lead and zinc can be reached even without pH adjustment. Some other metals, such as Mg and Mn, are removed together with the hazardous metals. Regarding the removal of Cl and K from the process, in this non-optimized case the removal efficiency was satisfactory: 60-70% for K when 80% of sodium was recovered, and close to 70% for Cl when 80% of sulfate was recovered. Copyright © 2017 Elsevier B.V. All rights reserved.

Projecting community changes in hazard exposure to support long-term risk reduction: A case study of tsunami hazards in the U.S. Pacific Northwest

Science.gov (United States)

Sleeter, Benjamin M.; Wood, Nathan J.; Soulard, Christopher E.; Wilson, Tamara

2017-01-01

Tsunamis have the potential to cause considerable damage to communities along the U.S. Pacific Northwest coastline. As coastal communities expand over time, the potential societal impact of tsunami inundation changes. To understand how community exposure to tsunami hazards may change in coming decades, we projected future development (i.e. urban, residential, and rural), households, and residents over a 50-year period (2011–2061) along the Washington, Oregon, and northern California coasts. We created a spatially explicit, land use/land cover, state-and-transition simulation model to project future developed land use based on historical development trends. We then compared our development projection results to tsunami-hazard zones associated with a Cascadia subduction zone (CSZ) earthquake. Changes in tsunami-hazard exposure by 2061 were estimated for 50 incorporated cities, 7 tribal reservations, and 17 counties relative to current (2011) estimates. Across the region, 2061 population exposure in tsunami-hazard zones was projected to increase by 3880 households and 6940 residents. The top ten communities with highest population exposure to CSZ-related tsunamis in 2011 are projected to remain the areas with the highest population exposure by 2061. The largest net population increases in tsunami-hazard zones were projected in the unincorporated portions of several counties, including Skagit, Coos, and Humboldt. Land-change simulation modeling of projected future development serves as an exploratory tool aimed at helping local governments understand the hazard-exposure implications of community growth and to include this knowledge in risk-reduction planning.

Residual stresses analysis of friction stir welding using one-way FSI simulation

International Nuclear Information System (INIS)

Kang, Sung Wook; Jang, Beom Seon; Song, Ha Cheol

2015-01-01

When certain mechanisms, such as plastic deformations and temperature gradients, occur and are released in a structure, stresses remain because of the shape of the structure and external constraints. These stresses are referred to as residual stresses. The base material locally expands during heating in the welding process. When the welding is completed and cooled to room temperature, the residual stresses are left at nearly the yield strength level. In the case of friction stir welding, the maximum temperature is 80% to 90% of the melting point of the materials. Thus, the residual stresses in the welding process are smaller than those in other fusion welding processes; these stresses have not been considered previously. However, friction stir welding residual stresses are sometimes measured at approximately 70% or above. These residual stresses significantly affect fatigue behavior and lifetime. The present study investigates the residual stress distributions in various welding conditions and shapes of friction stir welding. In addition, the asymmetric feature is considered in temperature and residual stress distribution. Heat transfer analysis is conducted using the commercial computational fluid dynamics program Fluent, and results are used in the finite element structural analysis with the ANSYS Multiphysics software. The calculated residual stresses are compared with experimental values using the X-ray diffraction method.

Residual stresses

International Nuclear Information System (INIS)

Macherauch, E.

1978-01-01

Residual stresses are stresses which exist in a material without the influence of external powers and moments. They come into existence when the volume of a material constantly changes its form as a consequence of mechanical, thermal, and/or chemical processes and is hindered by neighbouring volumes. Bodies with residual stress are in mechanical balance. These residual stresses can be manifested by means of all mechanical interventions disturbing this balance. Acoustical, optical, radiological, and magnetical methods involving material changes caused by residual stress can also serve for determining residual stress. Residual stresses have an ambivalent character. In technical practice, they are feared and liked at the same time. They cause trouble because they can be the cause for unexpected behaviour of construction elements. They are feared since they can cause failure, in the worst case with catastrophical consequences. They are appreciated, on the other hand, because, in many cases, they can contribute to improvements of the material behaviour under certain circumstances. But they are especially liked for their giving convenient and (this is most important) mostly uncontrollable explanations. For only in very few cases we have enough knowledge and possibilities for the objective evaluation of residual stresses. (orig.) [de

Modification of bauxite residue generated in the Bayer process by thermal treatment

International Nuclear Information System (INIS)

Garcia, M.C.S.; Pileggi, R.G.; John, V.M.; Gouvea, D.

2011-01-01

Red mud is the waste generated by the aluminum industry, and as other industrial waste presents complex characteristics with numerous difficulties in handling, as well as being a hazardous material due to its low granulometry, alkalinity and high amount generated. It is a waste with potential high polluter, aggravated by the generally adopted vulnerable disposal form, being this, the disposition of the residue in ponds designed for this purpose. The study and development of sustainable alternatives for the use of sludge, treated as raw materials from other processes, are important tendency and necessary trends in the global context of environmental preservation. This work deals with the thermal treatment as a method of modification of the characteristics of the residue, suggesting the reduction of alkalinity together with the lower leaching of alkaline ions. This approach can be a more reliable and environmentally safe disposal alternatives

Sources and management of hazardous waste in Papua New Guinea

Energy Technology Data Exchange (ETDEWEB)

Singh, K. [Univ. of Papua New Guinea (Papua New Guinea)

1996-12-31

Papua New Guinea (PNG) has considerable mineral wealth, especially in gold and copper. Large-scale mining takes place, and these activities are the source of most of PNG`s hazardous waste. Most people live in small farming communities throughout the region. Those living adjacent to mining areas have experienced some negative impacts from river ecosystem damage and erosion of their lands. Industry is centered mainly in urban areas and Generates waste composed of various products. Agricultural products, pesticide residues, and chemicals used for preserving timber and other forestry products also produce hazardous waste. Most municipal waste comes from domestic and commercial premises; it consists mainly of combustibles, noncombustibles, and other wastes. Hospitals generate pathogenic organisms, radioactive materials, and chemical and pharmaceutical laboratory waste. Little is known about the actual treatment of waste before disposal in PNG. Traditional low-cost waste disposal methods are usually practiced, such as use of landfills; storage in surface impoundments; and disposal in public sewers, rivers, and the sea. Indiscriminate burning of domestic waste in backyards is also commonly practiced in urban and rural areas. 10 refs., 4 tabs.

Statistical power to detect violation of the proportional hazards assumption when using the Cox regression model.

Science.gov (United States)

Austin, Peter C

2018-01-01

The use of the Cox proportional hazards regression model is widespread. A key assumption of the model is that of proportional hazards. Analysts frequently test the validity of this assumption using statistical significance testing. However, the statistical power of such assessments is frequently unknown. We used Monte Carlo simulations to estimate the statistical power of two different methods for detecting violations of this assumption. When the covariate was binary, we found that a model-based method had greater power than a method based on cumulative sums of martingale residuals. Furthermore, the parametric nature of the distribution of event times had an impact on power when the covariate was binary. Statistical power to detect a strong violation of the proportional hazards assumption was low to moderate even when the number of observed events was high. In many data sets, power to detect a violation of this assumption is likely to be low to modest.

Evaluation of residue-residue contact predictions in CASP9

KAUST Repository

Monastyrskyy, Bohdan

2011-01-01

This work presents the results of the assessment of the intramolecular residue-residue contact predictions submitted to CASP9. The methodology for the assessment does not differ from that used in previous CASPs, with two basic evaluation measures being the precision in recognizing contacts and the difference between the distribution of distances in the subset of predicted contact pairs versus all pairs of residues in the structure. The emphasis is placed on the prediction of long-range contacts (i.e., contacts between residues separated by at least 24 residues along sequence) in target proteins that cannot be easily modeled by homology. Although there is considerable activity in the field, the current analysis reports no discernable progress since CASP8.

Residual Fragments after Percutaneous Nephrolithotomy

Directory of Open Access Journals (Sweden)

Kaan Özdedeli

2012-09-01

Full Text Available Clinically insignificant residual fragments (CIRFs are described as asymptomatic, noninfectious and nonobstructive stone fragments (≤4 mm remaining in the urinary system after the last session of any intervention (ESWL, URS or PCNL for urinary stones. Their insignificance is questionable since CIRFs could eventually become significant, as their presence may result in recurrent stone growth and they may cause pain and infection due to urinary obstruction. They may become the source of persistent infections and a significant portion of the patients will have a stone-related event, requiring auxilliary interventions. CT seems to be the ultimate choice of assessment. Although there is no concensus about the timing, recent data suggests that it may be performed one month after the procedure. However, imaging can be done in the immediate postoperative period, if there are no tubes blurring the assessment. There is some evidence indicating that selective medical therapy may have an impact on decreasing stone formation rates. Retrograde intrarenal surgery, with its minimally invasive nature, seems to be the best way to deal with residual fragments.

Microwave calcination for plutonium immobilization and residue stabilization

Energy Technology Data Exchange (ETDEWEB)

Harris, M.J.; Rising, T.L.; Roushey, W.J.; Sprenger, G.S. [Kaiser-Hill Co., Golden, CO (United States)

1995-12-01

In the late 1980`s development was begun on a process using microwave energy to vitrify low level mixed waste sludge and transuranic mixed waste sludge generated in Building 374 at Rocky Flats. This process was shown to produce a dense, highly durable waste form. With the cessation of weapons production at Rocky Flats, the emphasis has changed from treatment of low level and TRU wastes to stabilizaiton of plutonium oxide and residues. This equipment is versatile and can be used as a heat source to calcine, react or vitrify many types of residues and oxides. It has natural economies in that it heats only the material to be treated, significantly reducing cycle times over conventional furnaces. It is inexpensive to operate in that most of the working components remain outside of any necessary contamination enclosure and therefore can easily be maintained. Limited testing has been successfully performed on cerium oxide (as a surrogate for plutonium oxide), surrogate electrorefining salts, surrogate residue sludge and residue ash. Future plans also include tests on ion exchange resins. In an attempt to further the usefullness of this technology, a mobile, self-contained microwave melting system is currently under development and expected to be operational at Rocky Flats Enviromental Technology Site by the 4th quarter of FY96.

Microwave calcination for plutonium immobilization and residue stabilization

International Nuclear Information System (INIS)

Harris, M.J.; Rising, T.L.; Roushey, W.J.; Sprenger, G.S.

1995-01-01

In the late 1980's development was begun on a process using microwave energy to vitrify low level mixed waste sludge and transuranic mixed waste sludge generated in Building 374 at Rocky Flats. This process was shown to produce a dense, highly durable waste form. With the cessation of weapons production at Rocky Flats, the emphasis has changed from treatment of low level and TRU wastes to stabilizaiton of plutonium oxide and residues. This equipment is versatile and can be used as a heat source to calcine, react or vitrify many types of residues and oxides. It has natural economies in that it heats only the material to be treated, significantly reducing cycle times over conventional furnaces. It is inexpensive to operate in that most of the working components remain outside of any necessary contamination enclosure and therefore can easily be maintained. Limited testing has been successfully performed on cerium oxide (as a surrogate for plutonium oxide), surrogate electrorefining salts, surrogate residue sludge and residue ash. Future plans also include tests on ion exchange resins. In an attempt to further the usefullness of this technology, a mobile, self-contained microwave melting system is currently under development and expected to be operational at Rocky Flats Enviromental Technology Site by the 4th quarter of FY96

Working towards a clearer and more helpful hazard map: investigating the influence of hazard map design on hazard communication

Science.gov (United States)

Thompson, M. A.; Lindsay, J. M.; Gaillard, J.

2015-12-01

Globally, geological hazards are communicated using maps. In traditional hazard mapping practice, scientists analyse data about a hazard, and then display the results on a map for stakeholder and public use. However, this one-way, top-down approach to hazard communication is not necessarily effective or reliable. The messages which people take away will be dependent on the way in which they read, interpret, and understand the map, a facet of hazard communication which has been relatively unexplored. Decades of cartographic studies suggest that variables in the visual representation of data on maps, such as colour and symbology, can have a powerful effect on how people understand map content. In practice, however, there is little guidance or consistency in how hazard information is expressed and represented on maps. Accordingly, decisions are often made based on subjective preference, rather than research-backed principles. Here we present the results of a study in which we explore how hazard map design features can influence hazard map interpretation, and we propose a number of considerations for hazard map design. A series of hazard maps were generated, with each one showing the same probabilistic volcanic ashfall dataset, but using different verbal and visual variables (e.g., different colour schemes, data classifications, probabilistic formats). Following a short pilot study, these maps were used in an online survey of 110 stakeholders and scientists in New Zealand. Participants answered 30 open-ended and multiple choice questions about ashfall hazard based on the different maps. Results suggest that hazard map design can have a significant influence on the messages readers take away. For example, diverging colour schemes were associated with concepts of "risk" and decision-making more than sequential schemes, and participants made more precise estimates of hazard with isarithmic data classifications compared to binned or gradational shading. Based on such

Microbiological Hazards of Household Toilets: Droplet Production and the Fate of Residual Organisms

Science.gov (United States)

Gerba, Charles P.; Wallis, Craig; Melnick, Joseph L.

1975-01-01

Large numbers of bacteria and viruses when seeded into household toilets were shown to remain in the bowl after flushing, and even continual flushing could not remove a persistent fraction. This was found to be due to the adsorption of the organisms to the porcelain surfaces of the bowl, with gradual elution occurring after each flush. Droplets produced by flushing toilets were found to harbor both bacteria and viruses which had been seeded. The detection of bacteria and viruses falling out onto surfaces in bathrooms after flushing indicated that they remain airborne long enough to settle on surface throughout the bathroom. Thus, there is a possibility that a person may acquire an infection from an aerosol produced by a toilet. PMID:169732

Hazard Analysis Database Report

Energy Technology Data Exchange (ETDEWEB)

GAULT, G.W.

1999-10-13

The Hazard Analysis Database was developed in conjunction with the hazard analysis activities conducted in accordance with DOE-STD-3009-94, Preparation Guide for US Department of Energy Nonreactor Nuclear Facility Safety Analysis Reports, for the Tank Waste Remediation System (TWRS) Final Safety Analysis Report (FSAR). The FSAR is part of the approved TWRS Authorization Basis (AB). This document describes, identifies, and defines the contents and structure of the TWRS FSAR Hazard Analysis Database and documents the configuration control changes made to the database. The TWRS Hazard Analysis Database contains the collection of information generated during the initial hazard evaluations and the subsequent hazard and accident analysis activities. The database supports the preparation of Chapters 3,4, and 5 of the TWRS FSAR and the USQ process and consists of two major, interrelated data sets: (1) Hazard Evaluation Database--Data from the results of the hazard evaluations; and (2) Hazard Topography Database--Data from the system familiarization and hazard identification.

Investigation of lithium thionyl chloride battery safety hazards

Science.gov (United States)

McDonald, R. C.; Dampier, F. W.; Wang, P.; Bennett, J. M.

1983-01-01

The chemistry of discharge and overdischarge in Li/SOCl2 cells has been examined with Raman emission, Fourier transform infrared, and electron spin resonance spectroscopies to determine if any hazardous reactions can occur. Under moderate discharge rate at room temperature, the electrolyte from discharged and cathode limited overdischarged cells contains primarily LiAlCl4.3 SO2, LiAlCl.2 SOCl2, and perhaps LiAlCl4.SOCl2.SO2; traces of SO3 are indicated. Three free radicals are present at low concentrations on discharge and cathode limited overdischarged with two additional radicals appearing on extended anode limited overdischarge. At least one of these is cationic polymeric sulfur. Both FTIR and ESR suggest intermediates exist with lifetimes on the order of days from discharge and overcharge. No hazardous reactions were observed at anytime. Pressure from SO2, a principal result of discharge, remains low due to the LiAlCl4.3 SO2, complex in solution. Scanning electron and optical microscopic investigations lithium dendrite structure. Individual dendrites do not grow any longer than about 50 microns or any thicker that about four microns in diameter before branching at random angles. The extent of dendritic growth and the fate of the dentrites depends on the discharge conditions. No overcharged hazards were encountered in this study though several hazard scenarios suggested themselves.

Organochlorine pesticide residues in sardinella aurita from the coastal waters of Accra-Tema, Ghana and their potential health risks

International Nuclear Information System (INIS)

Nyarko, E.; Botwe, B.O.; Bampoe, A.A.; Addo, S.; Armah, A.K.; Ntow, W.J.; Kelderman, P.

2011-01-01

Sardinella aurita and seawater samples from the Accra-Tema coast of Ghana were analysed for organochlorine (OC) pesticides using gas chromatography (GC) with electron capture detection (ECD). Residues of DDTs (p,p'-DDT, p'p'-DDE,p,p'-DDD), hexachlorocyclohexane (HCHs - α-HCH, β-HCH and γ-HCH), endosulfan (α-endosulfan, β-endosulfan, endosulfan sulphate) and heptachlor were detected in fish at average concentrations ranging from 3.0 to 1235.0 μg/kg wet wt. These residues were, however, below the detection limit in seawater samples. Significant differences (p < 0.05) in residue levels were also observed across sites, decreasing from Chorkor to Kpone for seven (7) of the residues that were detected in S. aurita. Evaluation of hazard ratios (HRs) and the health risk associated with OC exposure from consumption of sardinellas revealed a probability of adverse health effect due to p,p'-DDT, γ-HCH and heptachlor. Hence, p,p'-DDT, γ-HCH and heptachlor may be of particular health concern. (au)

Mixed-waste treatment -- What about the residuals? A comparative analysis of MSO and incineration

Energy Technology Data Exchange (ETDEWEB)

NONE

1993-06-01

This report examines the issues concerning final waste forms, or residuals, that result from the treatment of mixed waste in molten salt oxidation (MSO) and incinerator systems. MSO is a technology with the potential to treat a certain segment of the waste streams at US Department of Energy (DOE) sites. MSO was compared with incineration because incineration is the best demonstrated available technology (BDAT) for the same waste streams. The Grand Junction Projects Office (GJPO) and Oak Ridge National Laboratory (ORNL) prepared this report for the DOE Office of Environmental Restoration (OER). The goals of this study are to objectively evaluate the anticipated residuals from MSO and incineration, examine regulatory issues for these final waste forms, and determine secondary treatment options. This report, developed to address concerns that MSO residuals present unique disposal difficulties, is part of a larger effort to successfully implement MSO as a treatment technology for mixed and hazardous waste. A Peer Review Panel reviewed the MSO technology in November 1991, and the implementation effort is ongoing under the guidance of the MSO Task Force.

Mixed-waste treatment -- What about the residuals? A comparative analysis of MSO and incineration

International Nuclear Information System (INIS)

1993-06-01

This report examines the issues concerning final waste forms, or residuals, that result from the treatment of mixed waste in molten salt oxidation (MSO) and incinerator systems. MSO is a technology with the potential to treat a certain segment of the waste streams at US Department of Energy (DOE) sites. MSO was compared with incineration because incineration is the best demonstrated available technology (BDAT) for the same waste streams. The Grand Junction Projects Office (GJPO) and Oak Ridge National Laboratory (ORNL) prepared this report for the DOE Office of Environmental Restoration (OER). The goals of this study are to objectively evaluate the anticipated residuals from MSO and incineration, examine regulatory issues for these final waste forms, and determine secondary treatment options. This report, developed to address concerns that MSO residuals present unique disposal difficulties, is part of a larger effort to successfully implement MSO as a treatment technology for mixed and hazardous waste. A Peer Review Panel reviewed the MSO technology in November 1991, and the implementation effort is ongoing under the guidance of the MSO Task Force

Yields from pyrolysis of refinery residue using a batch process

Directory of Open Access Journals (Sweden)

S. Prithiraj

2017-12-01

Full Text Available Batch pyrolysis was a valuable process of assessing the potential of recovering and characterising products from hazardous waste materials. This research explored the pyrolysis of hydrocarbon-rich refinery residue, from crude oil processes, in a 1200 L electrically-heated batch retort. Furthermore, the off-gases produced were easily processed in compliance with existing regulatory emission standards. The methodology offers a novel, cost-effective and environmentally compliant method of assessing recovery potential of valuable products. The pyrolysis experiments yielded significant oil (70% with high calorific value (40 MJ/kg, char (14% with carbon content over 80% and non-condensable gas (6% with significant calorific value (240 kJ/mol. The final gas stream was subjected to an oxidative clean-up process with continuous on-line monitoring demonstrating compliance with South African emission standards. The gas treatment was overall economically optimal as only a smaller portion of the original residue was subjected to emission-controlling steps. Keywords: Batch pyrolysis, Volatiles, Oil yields, Char, Emissions, Oil recovery

Cavity pressure/residual stress measurements from the Non-Proliferation Experiment

Energy Technology Data Exchange (ETDEWEB)

Heinle, R.A.; Hudson, B.C. [Lawrence Livermore National Lab., CA (United States); Hatch, M.A. Jr.

1994-12-31

The Lawrence Livermore National Laboratory planned and conducted experiments on the Non-Proliferation Experiment to determine post-detonation gas pressure inside the explosive cavity and the residual rock stress in the region immediately outside the cavity. Before detonation there was significant concern that steam and detonation products would create very high temperatures and pressure in the blast cavity that would exist for weeks and months after firing. This could constitute a safety hazard to personnel re-entering the tunnel. Consequently the Lawrence Livermore National Laboratory was asked to field its Cavity Pressure/Residual stress monitor system on the Non-Proliferation Experiment. We obtained experimental data for the first 600 ms after the explosion and again several weeks after detonation upon tunnel re-entry. We recorded early-time cavity pressure of about 8.3 MPa. In addition we believe that the ends of our sensor hoses were subjected to an ambient driving pressure of about 0.5 MPa (absolute) that persisted until at least three weeks after zero time.

Exploration of resilience assessments for natural hazards

Science.gov (United States)

Lo Jacomo, Anna; Han, Dawei; Champneys, Alan

2017-04-01

The occurrence of extreme events due to natural hazards is difficult to predict. Extreme events are stochastic in nature, there is a lack of long term data on their occurrence, and there are still gaps in our understanding of their physical processes. This difficulty in prediction will be exacerbated by climate change and human activities. Yet traditional risk assessments measure risk as the probability of occurrence of a hazard, multiplied by the consequences of the hazard occurring, which ignores the recovery process. In light of the increasing concerns on disaster risks and the related system recovery, resilience assessments are being used as an approach which complements and builds on traditional risk assessments and management. In mechanical terms, resilience refers to the amount of energy per unit volume that a material can absorb while maintaining its ability to return to its original shape. Resilience was first applied in the fields of psychology and ecology, and more recently has been used in areas such as social sciences, economics, and engineering. A common metaphor for understanding resilience is the stability landscape. The landscape consists of a surface of interconnected basins, where each basin represents different states of a system, which is a point on the stability landscape. The resilience of the system is its capacity and tendency to remain within a particular basin. This depends on the topology of the landscape, on the system's current position, and on its reaction to different shocks and stresses. In practical terms, resilience assessments have been conducted for various purposes in different sectors. These assessments vary in their required inputs, the methodologies applied, and the output they produce. Some measures used for resilience assessments are hazard independent. These focus on the intrinsic capabilities of a system, for example the insurance coverage of a community, or the buffer capacity of a water storage reservoir. Other

Organic amendments for risk mitigation of organochlorine pesticide residues in old orchard soils

International Nuclear Information System (INIS)

Centofanti, Tiziana; McConnell, Laura L.; Chaney, Rufus L.; Beyer, W. Nelson; Andrade, Natasha A.; Hapeman, Cathleen J.; Torrents, Alba; Nguyen, Anh; Anderson, Marya O.; Novak, Jeffrey M.

2016-01-01

Performance of compost and biochar amendments for in situ risk mitigation of aged DDT, DDE and dieldrin residues in an old orchard soil was examined. The change in bioavailability of pesticide residues to Lumbricus terrestris L. relative to the unamended control soil was assessed using 4-L soil microcosms with and without plant cover in a 48-day experiment. The use of aged dairy manure compost and biosolids compost was found to be effective, especially in the planted treatments, at lowering the bioavailability factor (BAF) by 18–39%; however, BAF results for DDT in the unplanted soil treatments were unaffected or increased. The pine chip biochar utilized in this experiment was ineffective at lower the BAF of pesticides in the soil. The US EPA Soil Screening Level approach was used with our measured values. Addition of 10% of the aged dairy manure compost reduced the average hazard quotient values to below 1.0 for DDT + DDE and dieldrin. Results indicate this sustainable approach is appropriate to minimize risks to wildlife in areas of marginal organochlorine pesticide contamination. Application of this remediation approach has potential for use internationally in areas where historical pesticide contamination of soils remains a threat to wildlife populations. - Highlights: • Historical applications of organochlorine pesticides are a risk to local ecosystems. • Low cost and sustainable mitigation measures are needed to reduce risks. • Organic matter rich amendments were added to contaminated soil. • Earthworms microcosms were used to measure bioaccumulation factors. • Aged composts were most effective at mitigating risks to ecosystems. - Incorporation of aged dairy manure and biosolids compost amendments is an effective, low cost approach to mitigate risks to terrestrial wildlife from organochlorine pesticides in soils.

Handbook of hazardous waste management

International Nuclear Information System (INIS)

Metry, A.A.

1980-01-01

The contents of this work are arranged so as to give the reader a detailed understanding of the elements of hazardous waste management. Generalized management concepts are covered in Chapters 1 through 5 which are entitled: Introduction, Regulations Affecting Hazardous Waste Management, Comprehensive Hazardous Waste Management, Control of Hazardous Waste Transportation, and Emergency Hazardous Waste Management. Chapters 6 through 11 deal with treatment concepts and are entitled: General Considerations for Hazardous Waste Management Facilities, Physical Treatment of Hazardous Wastes, Chemical Treatment of Hazardous Wastes, Biological Treatment of Hazardous Wastes, Incineration of Hazardous Wastes, and Hazardous Waste Management of Selected Industries. Chapters 12 through 15 are devoted to ultimate disposal concepts and are entitled: Land Disposal Facilities, Ocean Dumping of Hazardous Wastes, Disposal of Extremely Hazardous Wastes, and Generalized Criteria for Hazardous Waste Management Facilities

Influence of turkey meat on residual nitrite in cured meat products.

Science.gov (United States)

Kilic, B; Cassens, R G; Borchert, L L

2001-02-01

A response surface experimental design was employed to estimate residual nitrite level at various initial nitrite concentrations, percent turkey meat in the formula, and heat quantity (F) values using a typical wiener as the test system. Pork and mechanically separated turkey were used as the meat ingredients. Residual nitrite and pH were measured at day 1, 7 days, 14 days, and 49 days after processing. Protein, fat, salt, moisture, and CIE (L*a*b*) color values were also determined. Results showed that the effect of turkey meat on residual nitrite level was significant (P meat in the formula resulted in lower residual nitrite levels at a fixed pH. The residual nitrite level was initially proportional to initial nitrite concentration, but it became a nonsignificant factor during longer storage time. Differences in heat quantity had a significant effect (P nitrite level initially. Greater heat quantity decreased residual nitrite level in finished cured meat products at a fixed pH. However, this effect became nonsignificant during longer storage. Reduction of residual nitrite in wieners because of turkey meat addition at a fixed pH was due to characteristics of the turkey tissue, but the mechanism of action remains unknown. It was also established that commercial wieners had a higher pH if poultry meat was included in the formulation.

Pesticide residue profile and nutrient characteristics of the Densu River Basin in Ghana

International Nuclear Information System (INIS)

Fianko, J.R.

2010-01-01

�-chlordane, endrin and δ-HCH were detected in fish, water and sediment samples. Aldrin and dieldrin levels detected were above the recommended limit of 0.03 μL -1 with endosulfan, endrin and chlordane registering levels above their recommended limits of 20.0μL -1 and 0.2 μL -1 respectively for drinking water. Pesticide residues in fish samples varied between 0.10 μgKg -1 to 30.90 μgKg -1 . The highest level was detected in Hepsetus odoe (HO-N). Contamination pattern of pesticide residues in fish samples was generally in the order of p'p'-DDE > heptachlor > γ- HCH > p'p'-DDT > endosulfan Sulphate > α-endosulfan > δ- HCH > γ-chlordane > dieldrin > endrin ketone > methoxychlor > endrin > aldrin > endrin aldehyde. Data obtained from the field survey regarding safe use of pesticides, toxicity awareness and symptoms among farmers indicated that a very high proportion of farmers were at high risk of pesticide poisoning from occupational exposure. More than 90% of farm workers did not practice safety precaution during pesticide formulation and application leading to considerable prevalence of pesticide related illness in this agricultural community. The presence of pesticide residues in fish was of further concern because fish is the main protein diet for humans in the basin. The estimated dose for aldrin, methoxychlor, γ-chlordane, endrin aldehyde, endrin ketone, endrin, p'p'-DDT and δ-HCH do not pose a direct hazard to human health, although present in fish samples since the values registered were lower than the reference doses. However, γ- HCH, heptachlor, α-endosulfan, endosulfan sulphate, p'p'-DDE and dieldrin levels exceeded the reference dose, indicating a great potential for systemic toxicity in children who are considered to be the most vulnerable population subgroup. In children, between the ages of 0 - 1year, the hazard indices of 2.64, 1.720, 1.736 and 0.792 were computed for α-endosulfan, heptachlor, endosulfan sulphate and dieldrin respectively while for

Egyptian Environmental Activities and Regulations for Management of Hazardous Substances and Hazardous Wastes

International Nuclear Information System (INIS)

El Zarka, M.

1999-01-01

A substantial use of hazardous substances is essential to meet the social and economic goals of the community in Egypt. Agrochemicals are being used extensively to increase crop yield. The outdated agrochemicals and their empty containers represent a serious environmental problem. Industrial development in different sectors in Egypt obligates handling of huge amounts of hazardous substances and hazardous wastes. The inappropriate handling of such hazardous substances creates several health and environmental problems. Egypt faces many challenges to control safe handling of such substances and wastes. Several regulations are governing handling of hazardous substances in Egypt. The unified Environmental Law 4 for the year 1994 includes a full chapter on the Management of Hazardous Substances and Hazardous Wastes. National and international activities have been taken to manage hazardous substances and hazardous wastes in an environmental sound manner

Hazard classification methodology

International Nuclear Information System (INIS)

Brereton, S.J.

1996-01-01

This document outlines the hazard classification methodology used to determine the hazard classification of the NIF LTAB, OAB, and the support facilities on the basis of radionuclides and chemicals. The hazard classification determines the safety analysis requirements for a facility

Anglesite and silver recovery from jarosite residues through roasting and sulfidization-flotation in zinc hydrometallurgy.

Science.gov (United States)

Han, Haisheng; Sun, Wei; Hu, Yuehua; Jia, Baoliang; Tang, Honghu

2014-08-15

Hazardous jarosite residues contain abundant valuable minerals that are difficult to be recovered by traditional flotation process. This study presents a new route, roasting combined with sulfidization-flotation, for the recovery of anglesite and silver from jarosite residues of zinc hydrometallurgy. Surface appearance and elemental distribution of jarosite residues was examined by scanning electron microscopy and energy dispersive X-ray spectrometry analysis, respectively. Decomposition and transformation mechanisms of jarosite residues were illustrated by differential thermal analysis. Results showed that after roasting combined with flotation, the grade and recovery of lead were 43.89% and 66.86%, respectively, and those of silver were 1.3 kg/t and 81.60%, respectively. At 600-700 °C, jarosite was decomposed to release encapsulated valuable minerals such as anglesite (PbSO4) and silver mineral; silver jarosite decomposed into silver sulfate (Ag2SO4); and zinc ferrite (ZnO · Fe2O3) decomposed into zinc sulfate (ZnSO4) and hematite (Fe2O3). Bared anglesite and silver minerals were modified by sodium sulfide and easily collected by flotation collectors. This study demonstrates that the combination of roasting and sulfidization-flotation provides a promising process for the recovery of zinc, lead, and silver from jarosite residues of zinc hydrometallurgy. Copyright © 2014 Elsevier B.V. All rights reserved.

Remaining Sites Verification Package for the 100-F-31, 144-F Sanitary Sewer System, Waste Site Reclassification Form 2006-033

Energy Technology Data Exchange (ETDEWEB)

L. M. Dittmer

2006-08-24

The 100-F-31 waste site is a former septic system that supported the inhalation laboratories, also referred to as the 144-F Particle Exposure Laboratory (132-F-2 waste site), which housed animals exposed to particulate material. The 100-F-31 waste site has been remediated to achieve the remedial action objectives specified in the Remaining Sites ROD. The results of verification sampling show that residual contaminant concentrations do not preclude any future uses and allow for unrestricted use of shallow zone soils. The results also demonstrate that residual contaminant concentrations are protective of groundwater and the Columbia River.

Testing to fulfill HACCP (Hazard Analysis Critical Control Points) requirements: principles and examples.

Science.gov (United States)

Gardner, I A

1997-12-01

On-farm HACCP (hazard analysis critical control points) monitoring requires cost-effective, yet accurate and reproducible tests that can determine the status of cows, milk, and the dairy environment. Tests need to be field-validated, and their limitations need to be established so that appropriate screening strategies can be initiated and test results can be rationally interpreted. For infections and residues of low prevalence, tests or testing strategies that are highly specific help to minimize false-positive results and excessive costs to the dairy industry. The determination of the numbers of samples to be tested in HACCP monitoring programs depends on the specific purpose of the test and the likely prevalence of the agent or residue at the critical control point. The absence of positive samples from a herd test should not be interpreted as freedom from a particular agent or residue unless the entire herd has been tested with a test that is 100% sensitive. The current lack of field-validated tests for most of the chemical and infectious agents of concern makes it difficult to ensure that the stated goals of HACCP programs are consistently achieved.

Human health risks associated with residual pesticide levels in edible tissues of slaughtered cattle in Benin City, Southern Nigeria

Directory of Open Access Journals (Sweden)

Isioma Tongo

2015-01-01

Full Text Available Pesticide residues in meat is of growing concern due to possible adverse effects on humans. Pesticide levels were assessed in five edible cattle parts: muscle, liver, kidney and tongue tissues to determine human health risk associated with consumption of these tissues. Health risk estimates were analysed using estimated daily intake (EDI, hazard quotient (HQ and hazard index (HI for two (2 age/weight categories: 1–11years/30 kg for children while 70 kg was used for adult. Risks were categorized for non-carcinogenic and carcinogenic health effects and measured at the average, maximum, 50th and 95th percentiles of the measured exposure concentrations (MEC. Total pesticide residues ranged from 2.38 to 3.86 μg/kg (muscle, 3.58 to 6.3 μg/kg (liver, 1.87 to 4.59 μg/kg (kidney and 2.54 to 4.35 μg/kg (tongue. Residual pesticide concentrations in the tissues were in the order: Liver > Tongue > Muscle > Kidney. The concentrations of all the assessed pesticides observed in the tissues were however lower than the recommended maximum residual limits (MRLs. Human health risk estimations for the children showed EDI values for heptachlor epoxide, aldrin and dieldrin exceeding threshold values. Non-cancer risk posed to children on consumption of contaminated cattle parts showed HQ values for heptachlor epoxide, aldrin, dieldrin and HI values for organochlorines exceeding 1, indicating the possibility of non-carcinogenic health risks to consumers especially children from consumption of cattle meat from the selected abattoirs.

Potential ligand-binding residues in rat olfactory receptors identified by correlated mutation analysis

Science.gov (United States)

Singer, M. S.; Oliveira, L.; Vriend, G.; Shepherd, G. M.

1995-01-01

A family of G-protein-coupled receptors is believed to mediate the recognition of odor molecules. In order to identify potential ligand-binding residues, we have applied correlated mutation analysis to receptor sequences from the rat. This method identifies pairs of sequence positions where residues remain conserved or mutate in tandem, thereby suggesting structural or functional importance. The analysis supported molecular modeling studies in suggesting several residues in positions that were consistent with ligand-binding function. Two of these positions, dominated by histidine residues, may play important roles in ligand binding and could confer broad specificity to mammalian odor receptors. The presence of positive (overdominant) selection at some of the identified positions provides additional evidence for roles in ligand binding. Higher-order groups of correlated residues were also observed. Each group may interact with an individual ligand determinant, and combinations of these groups may provide a multi-dimensional mechanism for receptor diversity.

Mapping residual stresses in PbWO4 crystals using photo-elastic analysis

International Nuclear Information System (INIS)

Lebeau, M.; Gobbi, L.; Majni, G.; Paone, N.; Pietroni, P.; Rinaldi, D.

2005-01-01

Large scintillating crystals are affected by internal stresses induced by the crystal growth temperature gradient remanence. Cutting boules (ingots) into finished crystal shapes allows for a partial tension relaxation but residual stresses remain the main cause of breaking. Quality control of residual stresses is essential in the application of Scintillating Crystals to high-energy physics calorimeters (e.g. CMS ECAL at CERN LHC). In this context the industrial process optimisation towards stress reduction is mandatory. We propose a fast technique for testing samples during the production process in order to evaluate the residual stress distribution after the first phases of mechanical processing. We mapped the stress distribution in PbWO 4 slabs cut from the same production boule. The analysis technique is based on the stress intensity determination using the photo-elastic properties of the samples. The stress distribution is mapped in each sample. The analysis shows that there are regions of high residual tension close to the seed position and at the boule periphery. These results should allow for adapting the industrial process to producing crystals with lower residual stresses

Efficacy of residual bifenthrin applied to landscape vegetation against Aedes albopictus.

Science.gov (United States)

Doyle, Melissa A; Kline, Daniel L; Allan, Sandra A; Kaufman, Phillip E

2009-06-01

The daytime biting mosquito Aedes albopictus is a nuisance pest commonly found in suburban yards. The recommended course of treatment for Ae. albopictus is to keep yards free of water-holding containers; however, infestations may require additional control methods such as residual pesticide applications to vegetation. Five plants commonly found in yards or in uncultivated areas in Gainesville, FL were chosen as substrates for evaluation of the effectiveness of residual bifenthrin against 5-7-day-old female Ae. albopictus. Knockdown of mosquitoes after 1 h of exposure was highest the day of and 7 days after treatment. Plant species clearly impacted the effectiveness of residual bifenthrin. One-hour knockdown 7 days after treatment remained high (>62%) only on azalea and holly bush vegetation. Knockdown counts 24 h after exposure demonstrated that residual efficacy of bifenthrin was highest on azalea, with >77% mortality for up to 35 days. Additional bioassays revealed significant differences in the knockdown rates of male, female, gravid, and blood-fed Ae. albopictus exposed to residual bifenthrin treatments, with the highest knockdown observed on the day of and 7 days after treatment.

Toward a federal/state/local partnership in hazardous materials transportation safety

International Nuclear Information System (INIS)

1982-09-01

In recognition of the federal government's responsibility for initiating a national strategy for hazardous materials transportation safety, the Materials Transportation Bureau (MTB) prepared an internal strategy paper for creating a federal/state/local partnership in hazardous materials transportation safety in August 1981. The paper outlined the scope of the hazardous materials transportation problem and established MTB's approach for creating an intergovernmental partnership for its resolution. This paper represents an update and refinement of the original plan, and is designed to chart the direction of the emerging federal/state/local relationship. The cornerstone of the plan remains the establishment of a single national set of safety regulations. It is on achievement of this objective that MTB's plan for development of enforcement, training, and emergency response capabilities at all levels of government is based. Chapter I introduces the problem with a desription of the economic importance of hazardous materials and discusses its implications for public safety. Chapter II defines the appropriate role for each level of government in the areas of rulemaking, enforcement, emergency response, and education. Chapter III demonstrates the need for uniform national safety standards and describes the economic and safety benefits of this approach. Chapter IV contains a detailed description of MTB's program for developing a successful intergovernmental partnership in hazardous materials transportation safety

Stabilization and plant uptake of N from 15N-labelled pea residue 16.5 years after incorporation in soil

DEFF Research Database (Denmark)

Laberge, G.; Ambus, P.; Hauggaard-Nielsen, H.

2006-01-01

The decline of N from N-15-labelled mature pea residues was followed in unplanted soil over 16.5 yr. Eight years after residue incorporation, 24% of the residue N-15 input was still present in the soil and, after 16.5 yr, 16% of the residue N-15 input remained. A double exponential model......-amended soils were obtaining 1.7% of their N from residue N. This is, to our knowledge, the longest study on decay of N in soils from N-15-labelled crop residues. The current study thus provides a unique data set for our empirical understanding of N-dynamics in agricultural systems, which is a prerequisite...

The contribution of coevolving residues to the stability of KDO8P synthase.

Directory of Open Access Journals (Sweden)

Sharon H Ackerman

2011-03-01

Full Text Available The evolutionary tree of 3-deoxy-D-manno-octulosonate 8-phosphate (KDO8P synthase (KDO8PS, a bacterial enzyme that catalyzes a key step in the biosynthesis of bacterial endotoxin, is evenly divided between metal and non-metal forms, both having similar structures, but diverging in various degrees in amino acid sequence. Mutagenesis, crystallographic and computational studies have established that only a few residues determine whether or not KDO8PS requires a metal for function. The remaining divergence in the amino acid sequence of KDO8PSs is apparently unrelated to the underlying catalytic mechanism.The multiple alignment of all known KDO8PS sequences reveals that several residue pairs coevolved, an indication of their possible linkage to a structural constraint. In this study we investigated by computational means the contribution of coevolving residues to the stability of KDO8PS. We found that about 1/4 of all strongly coevolving pairs probably originated from cycles of mutation (decreasing stability and suppression (restoring it, while the remaining pairs are best explained by a succession of neutral or nearly neutral covarions.Both sequence conservation and coevolution are involved in the preservation of the core structure of KDO8PS, but the contribution of coevolving residues is, in proportion, smaller. This is because small stability gains or losses associated with selection of certain residues in some regions of the stability landscape of KDO8PS are easily offset by a large number of possible changes in other regions. While this effect increases the tolerance of KDO8PS to deleterious mutations, it also decreases the probability that specific pairs of residues could have a strong contribution to the thermodynamic stability of the protein.

The residues and environmental risks of multiple veterinary antibiotics in animal faeces.

Science.gov (United States)

Li, Yan-Xia; Zhang, Xue-Lian; Li, Wei; Lu, Xiao-Fei; Liu, Bei; Wang, Jing

2013-03-01

To understand the residues and ecological risks of veterinary antibiotics (VAs) in animal faeces from concentrated animal feeding operations in northeastern China, 14 VAs were identified by high performance liquid chromatography, and the preliminary risks of six antibiotics were assessed using the hazard quotient (HQ). The investigated VAs occurred in 7.41 to 57.41 % of the 54 samples, and the levels ranged from 0.08 to 56.81 mg kg(-1). Tetracyclines were predominant with a maximum level of 56.81 mg kg(-1) mostly detected in pig faeces. Sulfonamides were common and detected with the highest concentration of 7.11 mg kg(-1). Fluoroquinolones were more widely detected in chicken faeces rather than in pig or cow faeces, which contained the dominant antibiotic enrofloxacin. In comparison, the residue of tylosin was less frequently found. The risk evaluations of the six antibiotics revealed that tetracyclines, especially oxytetracycline, displayed the greatest ecological risk because of its high HQ value of 15.75. The results of this study imply that multiple kinds of VAs were jointly used in animal feeding processes in the study area. These medicine residues in animal faeces may potentially bring ecological risks if the animal manure is not treated effectively.

Antibiotic residues in milk from small dairy farms in rural Peru.

Science.gov (United States)

Redding, L E; Cubas-Delgado, F; Sammel, M D; Smith, G; Galligan, D T; Levy, M Z; Hennessy, S

2014-01-01

The use of antibiotics in livestock can pose a public health threat, especially if antibiotic residues remain in the food product. Understanding how often and why farmers sell products with antibiotic residues is critical to improving the quality of these products. To understand how often milk with antibiotic residues is sold on small farms in a major dairy-producing region of Peru and identify factors associated with selling milk with antibiotic residues, we tested milk samples for antibiotic residues from every provider on three routes of commercial milk companies and from bulk tanks of farmers currently treating cows with antibiotics. We also asked farmers if they sold milk from treated cows and examined factors associated with the tendency to do so. The prevalence of milk contamination with antibiotic residues on commercial routes was low (0-4.2%); however, 33/36 farmers treating their animals with antibiotics sold milk that tested positive for antibiotic residues. The self-reported sale of milk from treated cows had a sensitivity, specificity, and positive and negative predictive values of 75.8%, 100%, 100% and 27.2%, respectively (with testing of milk for residues as the gold standard). Finally, 69/156 randomly selected farmers reported selling milk from treated cows, and farmers' knowledge of antibiotics and the milk purchaser were significantly associated with a farmer's tendency to report doing so. Educating farmers on the risks associated with antibiotics and enforcement of penalties for selling contaminated milk by milk companies are needed to improve milk quality.

''Hazardous'' terminology

International Nuclear Information System (INIS)

Powers, J.

1991-01-01

A number of terms (e.g., ''hazardous chemicals,'' ''hazardous materials,'' ''hazardous waste,'' and similar nomenclature) refer to substances that are subject to regulation under one or more federal environmental laws. State laws and regulations also provide additional, similar, or identical terminology that may be confused with the federally defined terms. Many of these terms appear synonymous, and it easy to use them interchangeably. However, in a regulatory context, inappropriate use of narrowly defined terms can lead to confusion about the substances referred to, the statutory provisions that apply, and the regulatory requirements for compliance under the applicable federal statutes. This information Brief provides regulatory definitions, a brief discussion of compliance requirements, and references for the precise terminology that should be used when referring to ''hazardous'' substances regulated under federal environmental laws. A companion CERCLA Information Brief (EH-231-004/0191) addresses ''toxic'' nomenclature

Effect of applied stress on the compressive residual stress introduced by laser peening

International Nuclear Information System (INIS)

Sumiya, Rie; Tazawa, Toshiyuki; Narazaki, Chihiro; Saito, Toshiyuki; Kishimoto, Kikuo

2016-01-01

Peening is the process which is able to be generated compressive residual stress and is known to be effective for preventing SCC initiation and improvement of fatigue strength. Laser peening is used for the nuclear power plant components in order to prevent SCC initiation. Although it is reported that the compressive residual stress decreases due to applied stresses under general operating condition, the change of residual stress might be large under excessive loading such as an earthquake. The objectives of this study are to evaluate the relaxation behavior of the compressive residual stress due to laser peening and to confirm the surface residual stress after loading. Therefore laser peened round bar test specimens of SUS316L which is used for the reactor internals of nuclear power plant were loaded at room temperature and elevated temperature and then surface residual stresses were measured by X-ray diffraction method. In the results of this test, it was confirmed that the compressive residual stress remained after applying uniform stress larger than 0.2% proof stress, and the effect of cyclic loading on the residual stress was small. The effect of applying compressive stress on the residual stress relaxation was confirmed to be less than that of applying tensile stress. Plastic deformation through a whole cross section causes the change in the residual stress distribution. As a result, the surface compressive residual stress is released. It was shown that the effect of specimen size on residual stress relaxation and the residual stress relaxation behavior in the stress concentration region can be explained by assumed stress relaxation mechanism. (author)

Hazard Analysis Database Report

CERN Document Server

Grams, W H

2000-01-01

The Hazard Analysis Database was developed in conjunction with the hazard analysis activities conducted in accordance with DOE-STD-3009-94, Preparation Guide for U S . Department of Energy Nonreactor Nuclear Facility Safety Analysis Reports, for HNF-SD-WM-SAR-067, Tank Farms Final Safety Analysis Report (FSAR). The FSAR is part of the approved Authorization Basis (AB) for the River Protection Project (RPP). This document describes, identifies, and defines the contents and structure of the Tank Farms FSAR Hazard Analysis Database and documents the configuration control changes made to the database. The Hazard Analysis Database contains the collection of information generated during the initial hazard evaluations and the subsequent hazard and accident analysis activities. The Hazard Analysis Database supports the preparation of Chapters 3 ,4 , and 5 of the Tank Farms FSAR and the Unreviewed Safety Question (USQ) process and consists of two major, interrelated data sets: (1) Hazard Analysis Database: Data from t...

Effect of Residue Nitrogen Concentration and Time Duration on Carbon Mineralization Rate of Alfalfa Residues in Regions with Different Climatic Conditions

Directory of Open Access Journals (Sweden)

saeid shafiei

2017-08-01

-arid (Sardouiyeh. The most suitable temperatures occurred from April to October in arid and semiarid climates and soil moisture is probably the key contributor to the rate of decomposition. The highest carbon loss in alfalfa in the cold, semiarid climate for a period of 8 months was 32.64%. The highest carbon decomposition rate constant was observed in the first 2 months of the incubation time. These results indicate that higher nitrogen residue resulted in greater decomposition of plant residue and lower carbon remaining in all tested climates. The higher nitrogen content of plant residue potentially increases the concentration of nitrogen in crop residue and may increase the decomposition rate. The strong relation between decomposition and climate has led to the belief that favorable climatic conditions can increase the decomposition rate on a global scale and positively decrease and distribute greenhouse gases in the atmosphere. In arid and semi-arid ecosystems, it is difficult to assess the decomposition rate based on climatic data; it seems to be related to temperature and available humidity. Furthermore, Austin & Vivanco (2006 reported that, in semi-arid climates, the litter decomposition rate decreased by 60 % when solar radiation was attenuated; they concluded that photodegradation exerts dominant control over litter decomposition in a dry ecosystem. Conclusions The results showed that, precipitation of the study area and soil moisture played a key role in the plant residue decomposition rate. In the cold semi-arid climate which moisture was available for decomposition of plant residues for a longer period of time, OC loss and decomposition rate constant were higher than those obtained for warm-arid and temperate-arid climatic conditions. It may be concluded that crop fertilization, which increases P and N concentrations of plant residue, increases decomposition rate of plant residue but decrease its mean residence time in soils.

Residual and Past Entropy for Concomitants of Ordered Random Variables of Morgenstern Family

Directory of Open Access Journals (Sweden)

M. M. Mohie EL-Din

2015-01-01

Full Text Available For a system, which is observed at time t, the residual and past entropies measure the uncertainty about the remaining and the past life of the distribution, respectively. In this paper, we have presented the residual and past entropy of Morgenstern family based on the concomitants of the different types of generalized order statistics (gos and give the linear transformation of such model. Characterization results for these dynamic entropies for concomitants of ordered random variables have been considered.

Anglesite and silver recovery from jarosite residues through roasting and sulfidization-flotation in zinc hydrometallurgy

International Nuclear Information System (INIS)

Han, Haisheng; Sun, Wei; Hu, Yuehua; Jia, Baoliang; Tang, Honghu

2014-01-01

Highlights: • Jarosite precipitate hindered the recovery of valuable minerals. • Under 600–700 °C, jarosite decomposed and released the encapsulated valuable minerals. • The bared valuable minerals were easily collected by flotation process. • The new process was promising for dealing with jarosite residues. - Abstract: Hazardous jarosite residues contain abundant valuable minerals that are difficult to be recovered by traditional flotation process. This study presents a new route, roasting combined with sulfidization-flotation, for the recovery of anglesite and silver from jarosite residues of zinc hydrometallurgy. Surface appearance and elemental distribution of jarosite residues was examined by scanning electron microscopy and energy dispersive X-ray spectrometry analysis, respectively. Decomposition and transformation mechanisms of jarosite residues were illustrated by differential thermal analysis. Results showed that after roasting combined with flotation, the grade and recovery of lead were 43.89% and 66.86%, respectively, and those of silver were 1.3 kg/t and 81.60%, respectively. At 600–700 °C, jarosite was decomposed to release encapsulated valuable minerals such as anglesite (PbSO 4 ) and silver mineral; silver jarosite decomposed into silver sulfate (Ag 2 SO 4 ); and zinc ferrite (ZnO·Fe 2 O 3 ) decomposed into zinc sulfate (ZnSO 4 ) and hematite (Fe 2 O 3 ). Bared anglesite and silver minerals were modified by sodium sulfide and easily collected by flotation collectors. This study demonstrates that the combination of roasting and sulfidization-flotation provides a promising process for the recovery of zinc, lead, and silver from jarosite residues of zinc hydrometallurgy

Remaining Sites Verification Package for the 1607-F7, 141-M Building Septic Tank. Attachment to Waste Site Reclassification Form 2006-040

International Nuclear Information System (INIS)

Dittmer, L.M.

2006-01-01

The 1607-F7, 141-M Building Septic Tank waste site was a septic tank and drain field that received sanitary sewage from the former 141-M Building. Remedial action was performed in August and November 2005. The results of verification sampling demonstrate that residual contaminant concentrations support future unrestricted land uses that can be represented by a rural-residential scenario. These results also show that residual concentrations support unrestricted future use of shallow zone soil and that contaminant levels remaining in the soil are protective of groundwater and the Columbia River

Experimental outgassing of toxic chemicals to simulate the characteristics of hazards tainting globally shipped products.

Directory of Open Access Journals (Sweden)

Lygia Therese Budnik

Full Text Available Ambient monitoring analyses may identify potential new public health hazards such as residual levels of fumigants and industrial chemicals off gassing from products and goods shipped globally. We analyzed container air with gas chromatography coupled to mass spectrometry (TD-2D-GC-MS/FPD and assessed whether the concentration of the volatiles benzene and 1,2-dichloroethane exceeded recommended exposure limits (REL. Products were taken from transport containers and analyzed for outgassing of volatiles. Furthermore, experimental outgassing was performed on packaging materials and textiles, to simulate the hazards tainting from globally shipped goods. The mean amounts of benzene in analyzed container air were 698-fold higher, and those of ethylene dichloride were 4.5-fold higher than the corresponding REL. More than 90% of all containers struck with toluene residues higher than its REL. For 1,2-dichloroethane 53% of containers, transporting shoes exceeded the REL. In standardized experimental fumigation of various products, outgassing of 1,2-dichloroethane under controlled laboratory conditions took up to several months. Globally produced transported products tainted with toxic industrial chemicals may contribute to the mixture of volatiles in indoor air as they are likely to emit for a long period. These results need to be taken into account for further evaluation of safety standards applying to workers and consumers.

Coil occlusion of residual shunts after surgical closure of patent ductus arteriosus.

Science.gov (United States)

Fujii, Yoko; Keene, Bruce W; Mathews, Kyle G; Atkins, Clarke E; Defrancesco, Teresa C; Hardie, Elizabeth M; Wakao, Yoshito

2006-12-01

OBJECTIVE; To describe use of coil embolization to occlude residual flow through a patent ductus arteriosus (PDA) after incomplete surgical ligation. Clinical study. Dogs (n=4) with continuous murmur after surgical ligation of PDA. After PDA ligation, residual ductal flow through the PDA was visible on color-flow Doppler examination and left ventricular end-diastolic diameter remained increased. Coil embolization by an arterial approach was performed to achieve complete occlusion of the PDA. Embolization coils were delivered without complications and hemodynamically successful occlusion was achieved. Doppler-visible flow resolved in 2 dogs within 3 months after embolization. Left ventricular end-diastolic diameter indexed to body weight decreased in all dogs. Transcatheter coil embolization appears to be a safe and minimally invasive procedure for complete occlusion of residual PDA flow after incomplete surgical ligation. Transcatheter coil embolization should be considered for correction of hemodynamically significant residual shunts in dogs that have incomplete PDA occlusion after open surgical ligation.

Electrodialytic removal of heavy metals and chloride from municipal solid waste incineration fly ash and air pollution control residue in suspension - test of a new two compartment experimental cell

DEFF Research Database (Denmark)

Kirkelund, Gunvor Marie; Magro, Cátia; Guedes, Paula

2015-01-01

Municipal solid waste incineration (MSWI) residues such as fly ash and air pollution control (APC) residues are classified as hazardous waste and disposed of, although they contain potential resources. The most problematic elements in MSWI residues are leachable heavy metals and salts. For reuse...... of MSWI residues in for instance concrete, the aim of remediation should be reduction of the heavy metal leaching, while at the same time keeping the alkaline pH, so the residue can replace cement. In this study a MSWI residues were subjected to electrodialytic remediation under various experimental...... heavy metal leaching except when the pH was reduced to a level below 8 for the fly ash. On the other hand, Cr leaching increased by the electrodialytic treatment. Cl leaching from the MSWI residues was less dependent on experimental conditions and was reduced in all experiments compared to the initial...

ThinkHazard!: an open-source, global tool for understanding hazard information

Science.gov (United States)

Fraser, Stuart; Jongman, Brenden; Simpson, Alanna; Nunez, Ariel; Deparday, Vivien; Saito, Keiko; Murnane, Richard; Balog, Simone

2016-04-01

Rapid and simple access to added-value natural hazard and disaster risk information is a key issue for various stakeholders of the development and disaster risk management (DRM) domains. Accessing available data often requires specialist knowledge of heterogeneous data, which are often highly technical and can be difficult for non-specialists in DRM to find and exploit. Thus, availability, accessibility and processing of these information sources are crucial issues, and an important reason why many development projects suffer significant impacts from natural hazards. The World Bank's Global Facility for Disaster Reduction and Recovery (GFDRR) is currently developing a new open-source tool to address this knowledge gap: ThinkHazard! The main aim of the ThinkHazard! project is to develop an analytical tool dedicated to facilitating improvements in knowledge and understanding of natural hazards among non-specialists in DRM. It also aims at providing users with relevant guidance and information on handling the threats posed by the natural hazards present in a chosen location. Furthermore, all aspects of this tool will be open and transparent, in order to give users enough information to understand its operational principles. In this presentation, we will explain the technical approach behind the tool, which translates state-of-the-art probabilistic natural hazard data into understandable hazard classifications and practical recommendations. We will also demonstrate the functionality of the tool, and discuss limitations from a scientific as well as an operational perspective.

Final hazard classification and auditable safety analysis for the 105-C Reactor Interim Safe Storage Project

International Nuclear Information System (INIS)

Rodovsky, T.J.; Larson, A.R.; Dexheimer, D.

1996-12-01

This document summarizes the inventories of radioactive and hazardous materials present in the 105-C Reactor Facility and the operations associated with the Interim Safe Storage Project which includes decontamination and demolition and interim safe storage of the remaining facility. This document also establishes a final hazard classification and verifies that appropriate and adequate safety functions and controls are in place to reduce or mitigate the risk associated with those operations

Remaining Sites Verification Package for the 100-F-33, 146-F Aquatic Biology Fish Ponds, Waste Site Reclassification Form 2006-021

Energy Technology Data Exchange (ETDEWEB)

L. M. Dittmer

2006-08-25

The 100-F-33, 146-F Aquatice Biology Fish Ponds waste site was an area with six small rectangular ponds and one large circular pond used to conduct tests on fish using various mixtures of river and reactor effluent water. The current site conditions achieve the remedial action objectives specified in the Remaining Sites ROD. The results of verification and applicable confirmatory sampling show that residual contaminant concentrations do not preclude any future uses and allow for unrestricted use of shallow zone soils. The results also demonstrate that residual contaminant concentrations are protective of groundwater and the Columbia River.

78 FR 79359 - Receipt of Several Pesticide Petitions Filed for Residues of Pesticide Chemicals in or on Various...

Science.gov (United States)

2013-12-30

... derivatization steps that was required for gas chromatography/mass spectrometry detection (GC/MSD), but not for... residues of ammonium acetate (CAS Registry No. 631-61-8), under 40 CFR 180.920, when used at not more than... ammonium acetate, there is little likelihood of foliar residues remaining on treated crops. Ammonium...

Propoxur (2-iso propoxy-phenyl-N-methylcarbamate) residues in cocoa beans. Part of a coordinated programme on isotopic-tracer aided studies of chemical residues in cotton seed, feed, oil and related products

International Nuclear Information System (INIS)

Adomako, D.

1982-05-01

Pod-bearing Amazon and Amelonado cocoa plants were sprayed with Unden 20% (propoxur, arprocarb, baygon) at the recommended rate of 210 g a.i./ha and twice the recommended rate at monthly intervals from July to October 1976, and cured beans from the ripe pods analysed for propoxur residues by gas chromatography. In a radiotracer study with 14 C-labelled propoxur, the effect of processing methods on residues and systemic uptake of propoxur from insecticide deposits on pod surfaces were also investigated. Residues did not exceed 0.03 mg/kg. There was no relationship between residues and harvesting time, cocoa type or rate of application. Contamination of beans with insecticide deposits on the pod surface during processing, and systemic uptake of insecticide from pod surfaces were negligible. Experiments were also designed to provide data on 14 C-propoxur residues in cocoa beans, uptake of the chemical from pod surfaces and persistence on the leaves and in the soil. Leaves were picked from the lowest five branches of the cocoa trees, 13 months after the application of 14 C-propoxur, dried at 80 0 for 4 days, stored and analysed for their 14 C-activity. Soil samples were collected at 15 cm and 30 cm distances from the trunk base of treated trees, dried, stored and analysed. The analytical procedure involved extraction and clean-up steps after a standard method using acetone, chloroform and a coagulating agent. Propoxur residues in cocoa leaves collected 13 months after the insecticide application ranged from 0.01 to 0.04 mg/kg. Residues in shells from cocoa pods treated with 14 C-propoxur 2 months prior to harvest did not exceed 0.02 mg/kg. Propoxur residues in soil samples collected at 6, 16, and 19 months following application ranged from 0.01 to 0.03 mg/kg. These low levels are probably related to volatilization and heavy rains. Possible binding to soil cannot be precluded. The low levels of propoxur are unlikely to present any toxicological hazard to humans

RESIDU PESTISIDA PADA SAYURAN KUBIS (Brassica oleracea L. DAN KACANG PANJANG ( Vigna sinensis L. YANG DIPASARKAN DI PASAR BADUNG DENPASAR

Directory of Open Access Journals (Sweden)

K Agung Sudewa

2012-11-01

Full Text Available Pesticides residue of organophosphate and carbamate i.e. diazinon, chlorpyriphos, fentoate, carbaril and BPMC were tested on cabbage (Brassica oleracea L. and long bean (Vigna sinensis L.. The purpose of this study was to know the level of pesticides residue remaining on cabbage and long bean marketed in Badung Market, Denpasar.The samples were determined proportionally based on purposive sampling method. The proportion of sample was 10% of the total cabbage and snake bean sold in Badung market.Result of present study showed that residue of insecticides such as diazinon, chlorpyriphos, fentoate, carbaril, and BPMC remaining on the head of cabbage and snake bean marketed in Badung market was affected by the frequencies of their use in the field, in which chlorpyriphos was used by 60-65% of the farmers and carbaril by 40% of the farmers. Their residues on cabbage anf snake bean were 0.525 ppm and 1.296 ppm for chlorpyriphos (organophosphate; 0.303 ppm and 0.471 ppm for carbaril (carbamate. These result suggested that residue of chlorpyriphos on cabbage and snake bean were higher than MRL (Maximum Residue Limit for vegetable crops, i.e. 0.5 ppm.

Household hazardous waste data for the UK by direct sampling.

Science.gov (United States)

Slack, Rebecca J; Bonin, Michael; Gronow, Jan R; Van Santen, Anton; Voulvoulis, Nikolaos

2007-04-01

The amount of household hazardous waste (HHW) disposed of in the United Kingdom (UK) requires assessment. This paper describes a direct analysis study carried out in three areas in southeast England involving over 500 households. Each participating householder was provided with a special bin in which to place items corresponding to a list of HHW. The amount of waste collected was split into nine broad categories: batteries, home maintenance (DIY), vehicle upkeep, pesticides, pet care, pharmaceuticals, photographic chemicals, household cleaners, and printer cartridges. Over 1 T of waste was collected from the sample households over a 32-week period, which would correspond to an estimated 51,000 T if extrapolated to the UK population for the same period or over 7,000 T per month. Details of likely disposal routes adopted by householders were also sought, demonstrating the different pathways selected for different waste categories. Co-disposal with residual household waste dominated for waste batteries and veterinary medicines, hence avoiding classification as hazardous waste under new UK waste regulations. The information can be used to set a baseline for the management of HHW and provides information for an environmental risk assessment of the disposal of such wastes to landfill.

Volcanic hazards and public response

Science.gov (United States)

Peterson, Donald W.

1988-05-01

Although scientific understanding of volcanoes is advancing, eruptions continue to take a substantial toll of life and property. Some of these losses could be reduced by better advance preparation, more effective flow of information between scientists and public officials, and better understanding of volcanic behavior by all segments of the public. The greatest losses generally occur at volcanoes that erupt infrequently where people are not accustomed to dealing with them. Scientists sometimes tend to feel that the blame for poor decisions in emergency management lies chiefly with officials or journalists because of their failure to understand the threat. However, the underlying problem embraces a set of more complex issues comprising three pervasive factors. The first factor is the volcano: signals given by restless volcanoes are often ambiguous and difficult to interpret, especially at long-quiescent volcanoes. The second factor is people: people confront hazardous volcanoes in widely divergent ways, and many have difficulty in dealing with the uncertainties inherent in volcanic unrest. The third factor is the scientists: volcanologists correctly place their highest priority on monitoring and hazard assessment, but they sometimes fail to explain clearly their conclusions to responsible officials and the public, which may lead to inadequate public response. Of all groups in society, volcanologists have the clearest understanding of the hazards and vagaries of volcanic activity; they thereby assume an ethical obligation to convey effectively their knowledge to benefit all of society. If society resists, their obligation nevertheless remains. They must use the same ingenuity and creativity in dealing with information for the public that they use in solving scientific problems. When this falls short, even excellent scientific results may be nullified.

Multi-Hazard Interactions in Guatemala

Science.gov (United States)

Gill, Joel; Malamud, Bruce D.

2017-04-01

In this paper, we combine physical and social science approaches to develop a multi-scale regional framework for natural hazard interactions in Guatemala. The identification and characterisation of natural hazard interactions is an important input for comprehensive multi-hazard approaches to disaster risk reduction at a regional level. We use five transdisciplinary evidence sources to organise and populate our framework: (i) internationally-accessible literature; (ii) civil protection bulletins; (iii) field observations; (iv) stakeholder interviews (hazard and civil protection professionals); and (v) stakeholder workshop results. These five evidence sources are synthesised to determine an appropriate natural hazard classification scheme for Guatemala (6 hazard groups, 19 hazard types, and 37 hazard sub-types). For a national spatial extent (Guatemala), we construct and populate a "21×21" hazard interaction matrix, identifying 49 possible interactions between 21 hazard types. For a sub-national spatial extent (Southern Highlands, Guatemala), we construct and populate a "33×33" hazard interaction matrix, identifying 112 possible interactions between 33 hazard sub-types. Evidence sources are also used to constrain anthropogenic processes that could trigger natural hazards in Guatemala, and characterise possible networks of natural hazard interactions (cascades). The outcomes of this approach are among the most comprehensive interaction frameworks for national and sub-national spatial scales in the published literature. These can be used to support disaster risk reduction and civil protection professionals in better understanding natural hazards and potential disasters at a regional scale.

ASEAN grid-connected biomass residues fired cogeneration plants

International Nuclear Information System (INIS)

Adnan, M.F.; Alias, R.

2006-01-01

Energy supply is one of the major concerns in the world. With uncertainty in the main oil suppliers, the oil price is expected to remain high due to continuous demand from the world. Since oil is mostly used for electricity and transportation, its shortage would cause major disruptions in our daily activities. Thus to counter this scenario and faster depletion of fossil fuel resources, various measures have been taken to find alternative source of energy such as renewable energy. One of the renewable energy sources is from biomass residues which is aplenty particularly in ASEAN. Through one of the collaboration programme between ASEAN and EC which is The EC-ASEAN Cogeneration Programme, a number of Full-Scale Demonstration Projects (FSDP) using biomass residues have been commissioned and implemented successfully. Four of the FSDPs in Thailand and Malaysia are connected to the grid. These projects have been operating very well and since the fuel is commonly available in this ASEAN region, duplication should not be a problem. Thus, this paper would highlight the success stories in implementing biomass residues grid connected project while enhancing cooperation between ASEAN and EC. (Author)

Assessment of volcanic hazards, vulnerability, risk and uncertainty (Invited)

Science.gov (United States)

Sparks, R. S.

2009-12-01

A volcanic hazard is any phenomenon that threatens communities . These hazards include volcanic events like pyroclastic flows, explosions, ash fall and lavas, and secondary effects such as lahars and landslides. Volcanic hazards are described by the physical characteristics of the phenomena, by the assessment of the areas that they are likely to affect and by the magnitude-dependent return period of events. Volcanic hazard maps are generated by mapping past volcanic events and by modelling the hazardous processes. Both these methods have their strengths and limitations and a robust map should use both approaches in combination. Past records, studied through stratigraphy, the distribution of deposits and age dating, are typically incomplete and may be biased. Very significant volcanic hazards, such as surge clouds and volcanic blasts, are not well-preserved in the geological record for example. Models of volcanic processes are very useful to help identify hazardous areas that do not have any geological evidence. They are, however, limited by simplifications and incomplete understanding of the physics. Many practical volcanic hazards mapping tools are also very empirical. Hazards maps are typically abstracted into hazards zones maps, which are some times called threat or risk maps. Their aim is to identify areas at high levels of threat and the boundaries between zones may take account of other factors such as roads, escape routes during evacuation, infrastructure. These boundaries may change with time due to new knowledge on the hazards or changes in volcanic activity levels. Alternatively they may remain static but implications of the zones may change as volcanic activity changes. Zone maps are used for planning purposes and for management of volcanic crises. Volcanic hazards maps are depictions of the likelihood of future volcanic phenomena affecting places and people. Volcanic phenomena are naturally variable, often complex and not fully understood. There are

A review of experimental methods for determining residual creep life

International Nuclear Information System (INIS)

Bolton, C.J.

1977-11-01

Experimental methods available for determining how much creep life remains at a particular time in the high temperature service of a component are reviewed. After a brief consideration of the limitations of stress rupture extrapolation techniques, the application of post-exposure creep testing is considered. Ways of assessing the effect of microstructural degradation on residual life are then reviewed. It is pointed out that while this type of work will be useful for certain materials, there are other materials in which 'mechanical damage' such as cavitation will be more important. Cavitation measurement techniques are therefore reviewed. The report ends with a brief consideration of the use of crack growth measurements in assessing the residual life of cracked components. (author)

A survey of residual analysis and a new test of residual trend.

Science.gov (United States)

McDowell, J J; Calvin, Olivia L; Klapes, Bryan

2016-05-01

A survey of residual analysis in behavior-analytic research reveals that existing methods are problematic in one way or another. A new test for residual trends is proposed that avoids the problematic features of the existing methods. It entails fitting cubic polynomials to sets of residuals and comparing their effect sizes to those that would be expected if the sets of residuals were random. To this end, sampling distributions of effect sizes for fits of a cubic polynomial to random data were obtained by generating sets of random standardized residuals of various sizes, n. A cubic polynomial was then fitted to each set of residuals and its effect size was calculated. This yielded a sampling distribution of effect sizes for each n. To test for a residual trend in experimental data, the median effect size of cubic-polynomial fits to sets of experimental residuals can be compared to the median of the corresponding sampling distribution of effect sizes for random residuals using a sign test. An example from the literature, which entailed comparing mathematical and computational models of continuous choice, is used to illustrate the utility of the test. © 2016 Society for the Experimental Analysis of Behavior.

77 FR 44528 - Dry Cargo Residue Discharges in the Great Lakes

Science.gov (United States)

2012-07-30

... occurs during cargo unloading. Within tunnels, large pieces of DCR that remain after unloading should be...) as a condition in which deck residues ``consist only of dust, powder, or isolated and random pieces... associated with the amount of DCR going dealing with removal of this IR into the water and voluntary...

Antibiotic, Pesticide, and Microbial Contaminants of Honey: Human Health Hazards

Directory of Open Access Journals (Sweden)

Noori Al-Waili

2012-01-01

Full Text Available Agricultural contamination with pesticides and antibiotics is a challenging problem that needs to be fully addressed. Bee products, such as honey, are widely consumed as food and medicine and their contamination may carry serious health hazards. Honey and other bee products are polluted by pesticides, heavy metals, bacteria and radioactive materials. Pesticide residues cause genetic mutations and cellular degradation and presence of antibiotics might increase resistant human or animal's pathogens. Many cases of infant botulisms have been attributed to contaminated honey. Honey may be very toxic when produced from certain plants. Ingestion of honey without knowing its source and safety might be problematic. Honey should be labeled to explore its origin, composition, and clear statement that it is free from contaminants. Honey that is not subjected for analysis and sterilization should not be used in infants, and should not be applied to wounds or used for medicinal purposes. This article reviews the extent and health impact of honey contamination and stresses on the introduction of a strict monitoring system and validation of acceptable minimal concentrations of pollutants or identifying maximum residue limits for bee products, in particular, honey.

78 FR 46940 - Hazardous and Solid Waste Management System: Identification and Listing of Special Wastes...

Science.gov (United States)

2013-08-02

...The U.S. Environmental Protection Agency (EPA or the Agency) invites comment on additional information obtained in conjunction with the proposed rule: Hazardous and Solid Waste Management System: Identification and Listing of Special Wastes; Disposal of Coal Combustion Residuals From Electric Utilities that was published in the Federal Register on June 21, 2010. This information is categorized as: additional data to supplement the Regulatory Impact Analysis and risk assessment, information on large scale fill, and data on the surface impoundment structural integrity assessments. EPA is also seeking comment on two issues associated with the requirements for coal combustion residual management units. The Agency is not reopening any other aspect of the proposal or underlying support documents, and will consider comments on any issues other than those raised in the NODA to be late comments and not part of the rulemaking record.

Association between mortality and residual radiation in Nagasaki atomic bomb survivors exposed at long-distance from the hypocenter

International Nuclear Information System (INIS)

Kondo, Hisayoshi; Mine, Mariko; Yokota, Kenichi; Shibata, Yoshisada

2012-01-01

Mortality of Nagasaki A-bomb survivors exposed at 3 km or longer distance from the hypocenter was compared with that of those who were additionally exposed to residual radiation because of their entrance in the area at 1 km or closer to the center within 24 hr post explosion. The latter survivors (group I), 2,357 men with average age of 28.4 y and 2,618 women of 26.5 y at the exposure, were alive at 1970, and the former (group II, without exposure to residual radiation) was selected to match their numbers in sex, exposed distance, ages at exposure and at start of the follow-up study to those of group I. Follow-up was conducted from 1970 to 2007, and their total, malignant, cerebrovascular, cardiac and pneumonic deaths were observed. Cox proportional hazard model was used for estimation of mortality risk with covariates of sex and age at start of the study. The risk in group II was defined to be standard. Ages at start of the study were 53.3 and 51.4 y in men and women, respectively. Crude mortality tended to be higher in men of group I at ages of 40-49 and 50-59 y at start of the study. Hazard ratios of total and malignant tumor deaths in group I were 0.965 and 1.092, respectively, without statistic significance from group II and of other deaths, 0.982-0.999, also of statistic insignificance. Thus increased mortality due to residual radiation was not observed. (T.T.)

Scoring protein interaction decoys using exposed residues (SPIDER): a novel multibody interaction scoring function based on frequent geometric patterns of interfacial residues.

Science.gov (United States)

Khashan, Raed; Zheng, Weifan; Tropsha, Alexander

2012-08-01

Accurate prediction of the structure of protein-protein complexes in computational docking experiments remains a formidable challenge. It has been recognized that identifying native or native-like poses among multiple decoys is the major bottleneck of the current scoring functions used in docking. We have developed a novel multibody pose-scoring function that has no theoretical limit on the number of residues contributing to the individual interaction terms. We use a coarse-grain representation of a protein-protein complex where each residue is represented by its side chain centroid. We apply a computational geometry approach called Almost-Delaunay tessellation that transforms protein-protein complexes into a residue contact network, or an undirectional graph where vertex-residues are nodes connected by edges. This treatment forms a family of interfacial graphs representing a dataset of protein-protein complexes. We then employ frequent subgraph mining approach to identify common interfacial residue patterns that appear in at least a subset of native protein-protein interfaces. The geometrical parameters and frequency of occurrence of each "native" pattern in the training set are used to develop the new SPIDER scoring function. SPIDER was validated using standard "ZDOCK" benchmark dataset that was not used in the development of SPIDER. We demonstrate that SPIDER scoring function ranks native and native-like poses above geometrical decoys and that it exceeds in performance a popular ZRANK scoring function. SPIDER was ranked among the top scoring functions in a recent round of CAPRI (Critical Assessment of PRedicted Interactions) blind test of protein-protein docking methods. Copyright © 2012 Wiley Periodicals, Inc.

Hazard management at the workplace

International Nuclear Information System (INIS)

Hasfazilah Hassan; Azimawati Ahmad; Syed Asraf Fahlawi Wafa S M Ghazi; Hairul Nizam Idris

2005-01-01

Failure to ensure health and safety environment at workplace will cause an accident involving loss to the time, human resource, finance and for the worse case effect the moral value of an organization. If we go through to the cause of the accident, it is impossible to have a totally safety workplace. It is because every process in work activities has it own hazard elements. The purpose of this paper is to discuss the best action to prevent from the hazard with a comprehensive and effectiveness hazard management. Hazard management is the one of the pro-active hazard control. With this we manage to identify and evaluate the hazard and control the hazard risk. Therefore, hazard management should be screened constantly and continuously to make sure work hazard always in control. (Author)

DOE Hazardous Waste Program

International Nuclear Information System (INIS)

Eyman, L.D.; Craig, R.B.

1985-01-01

The goal of the DOE Hazardous Waste Program is to support the implementation and improvement of hazardous-chemical and mixed-radioactive-waste management such that public health, safety, and the environment are protected and DOE missions are effectively accomplished. The strategy for accomplishing this goal is to define the character and magnitude of hazardous wastes emanating from DOE facilities, determine what DOE resources are available to address these problems, define the regulatory and operational constraints, and develop programs and plans to resolve hazardous waste issues. Over the longer term the program will support the adaptation and application of technologies to meet hazardous waste management needs and to implement an integrated, DOE-wide hazardous waste management strategy. 1 reference, 1 figure

Hazardous and mixed waste management at UMTRA sites

International Nuclear Information System (INIS)

Hampill, H.G.

1988-01-01

During the early stages of the Uranium Mill Tailings Remedial Action Project, there were some serious questions regarding the ownership of and consequently the responsibility for disposal of hazardous wastes at UMTRA sites. In addition to State and Indian Tribe waste disposal regulations, UMTRA must also conform to guidelines established by the NRC, OSHA, EPA, and DOT. Because of the differing regulatory thrusts of these agencies, UMTRA has to be vigilant in order to ensure that the disposal of each parcel of waste material is in compliance with all regulations. Mixed-waste disposal presents a particularly difficult problem. No single agency is willing to lay claim to the regulation of mixed-wastes, and no conventional waste disposal facility is willing to accept it. Consequently, the disposal of each lot of mixed-waste at UMTRA sites must be handled on a case by case basis. A recently published position paper which spells out UMTRA policy on waste materials indicates that wastes found at UMTRA sites are either residual radioactive wastes, or mixed-wastes, or for the disposal of hazardous waste is determined by the time the original material arrived. If it arrived prior to the termination of the AEC uranium supply contract, its disposal is the responsibility of UMTRA. If it arrived after the end of the contract, the responsibility for disposal lies with the former operator

Temporal Changes in Community Resilience to Drought Hazard

Science.gov (United States)

Mihunov, V.

2017-12-01

The threat of droughts and their associated impacts on the landscape and human communities have long been recognized. While considerable research on the climatological aspect of droughts has been conducted, studies on the resilience of human communities to the effects of drought remain limited. Understanding how different communities respond to and recover from the drought hazard, i.e. their community resilience, should inform the development of better strategies to cope with the hazard. This research assesses community resilience to drought hazard in South-Central U.S. and captures the temporal changes of community resilience in the region facing the climate change. First, the study applies the Resilience Inference Measurement (RIM) framework using the existing drought incidence, crop damage, socio-economic and food-water-energy nexus variables, which allows to assign county-level resilience scores in the study region and derive variables contributing to the resilience. Second, it captures the temporal changes in community resilience by using the model extracted from the RIM study and socio-economic data from several consecutive time periods. The resilience measurement study should help understand the complex process underlying communities' response to the drought impacts. The results identify gaps in resilience planning and help the improvement of the community resilience to the droughts of increasing frequency and intensity.

Modelling of the long-term fate of pesticide residues in agricultural soils and their surface exchange with the atmosphere: Part II. Projected long-term fate of pesticide residues.

Science.gov (United States)

Scholtz, M T; Bidleman, T F

2007-05-01

In the first part of this paper, a simple coupled dynamic soil-atmosphere model for studying the gaseous exchange of pesticide soil residues with the atmosphere is described and evaluated by comparing model results with published measurements of pesticide concentrations in air and soil. In Part II, the model is used to study the concentration profiles of pesticide residues in both undisturbed and annually tilled agricultural soils. Future trends are estimated for the measured air and soil concentrations of lindane and six highly persistent pesticides (toxaphene, p,p'-DDE, dieldrin, cis- and trans-chlordane and trans-nonachlor) over a twenty-year period due to volatilization and leaching into the deeper soil. Wet deposition and particle associated pesticide deposition (that increase soil residue concentrations) and soil erosion, degradation in the soil (other than for lindane) and run-off in precipitation are not considered in this study. Estimates of the rain deposition fluxes are reported that show that, other than for lindane, net volatilization fluxes greatly exceed rain deposition fluxes. The model shows that the persistent pesticides studied are highly immobile in soil and that loss of these highly persistent residues from the soil is by volatilization rather than leaching into the deeper soil. The soil residue levels of these six pesticides are currently sources of net volatilization to the atmosphere and will remain so for many years. The maximum rate of volatilization from the soil was simulated by setting the atmospheric background concentration to zero; these simulations show that the rates of volatilization will not be significantly increased since soil resistance rather than the atmospheric concentration controls the volatilization rates. Annual tilling of the soils increases the volatilization loss to the atmosphere. Nonetheless, the model predicts that, if only air-soil exchange is considered, more than 76% of current persistent pesticide residues

Relative Hazard Calculation Methodology

International Nuclear Information System (INIS)

DL Strenge; MK White; RD Stenner; WB Andrews

1999-01-01

The methodology presented in this document was developed to provide a means of calculating the RH ratios to use in developing useful graphic illustrations. The RH equation, as presented in this methodology, is primarily a collection of key factors relevant to understanding the hazards and risks associated with projected risk management activities. The RH equation has the potential for much broader application than generating risk profiles. For example, it can be used to compare one risk management activity with another, instead of just comparing it to a fixed baseline as was done for the risk profiles. If the appropriate source term data are available, it could be used in its non-ratio form to estimate absolute values of the associated hazards. These estimated values of hazard could then be examined to help understand which risk management activities are addressing the higher hazard conditions at a site. Graphics could be generated from these absolute hazard values to compare high-hazard conditions. If the RH equation is used in this manner, care must be taken to specifically define and qualify the estimated absolute hazard values (e.g., identify which factors were considered and which ones tended to drive the hazard estimation)

Phytotoxicity and groundwater impacts of leaching from thermal treatment residues in roadways.

Science.gov (United States)

Phoungthong, Khamphe; Shao, Li-Ming; He, Pin-Jing; Zhang, Hua

2018-01-01

The use of coal fly ash (CFA), municipal solid waste incinerator bottom ash (MSWIBA) and flue gas desulfurization residue (FGDR) in road construction has become very common owing to its economical advantages. However, these residues may contain toxic constituents that pose an environmental risk if they leach out and flow through the soil, surface water and groundwater. Therefore, it is necessary to assess the ecotoxicity and groundwater impact of these residues before decisions can be made regarding their utilization for road construction. In this study, the physico-chemical characteristics, leaching and phytotoxicity of these residues were investigated. Specifically, multivariate analyses were used to evaluate the contributions of the leaching constituents of the CFA, MSWIBA and FGDR leachates to the germination index of wheat seeds. B, Ba, Cr, Cu, Fe and Pb were found to be more toxic to the wheat seeds than the other heavy metals. Furthermore, the leached concentrations of the constituents from the CFA, MSWIBA and FGDR were below the regulatory threshold limits of the Chinese identification standard for hazardous wastes. Analyses conducted using a numerical groundwater model (WiscLEACH) indicated that the predicted field concentrations of metals from the CFA, MSWIBA and FGDR increased with time up to about 30years at the point of compliance, then decreased with time and distance. Overall, this study demonstrated that the risks resulting from MSWIBA, CFA and FGDR leaching could be assessed before its utilization for road construction, providing crucial information for the adoption of these alternative materials. Copyright © 2016. Published by Elsevier B.V.

Child Labour Remains "Massive Problem."

Science.gov (United States)

World of Work, 2002

2002-01-01

Despite significant progress in efforts to abolish child labor, an alarming number of children are engaged in its worst forms. Although 106 million are engaged in acceptable labor (light work for those above the minimum age for employment), 246 million are involved in child labor that should be abolished (under minimum age, hazardous work). (JOW)

Effectiveness of dynamic MRI for diagnosing pericicatricial minimal residual breast cancer following excisional biopsy

International Nuclear Information System (INIS)

Kawashima, Hiroko; Tawara, Mari; Suzuki, Masayuki; Matsui, Osamu; Kadoya, Masumi

2001-01-01

The purpose of this study was to investigate the effectiveness of dynamic MRI for diagnosing pericicatricial minimal residual breast cancer following excisional biopsy. Twenty-six patients who underwent excisional biopsy of a tumor or calcified lesion of the breast underwent gadolinium-enhanced dynamic MRI by the fat-saturated 2D fast spoiled gradient echo (SPGR) sequence (group 1), 24 patients by the spectral IR enhanced 3D fast gradient echo (Efgre3d) sequence (group 2). Pericicatricial residual cancer was confirmed histologically in 29 of the 50 patients. The overall sensitivity, specificity, accuracy, positive predictive value, and negative predictive value of MRI for residual cancer diagnosis was 66, 81, 72, 83 and 63%. A nodular, thick and discontinuous enhanced rim around the scar is indicative of a residual tumor. However, false-positive findings due to granulation or proliferative fibrocystic change remain limitations

Effectiveness of dynamic MRI for diagnosing pericicatricial minimal residual breast cancer following excisional biopsy

Energy Technology Data Exchange (ETDEWEB)

Kawashima, Hiroko E-mail: hirokok@med.kanazawa-u.ac.jp; Tawara, Mari; Suzuki, Masayuki; Matsui, Osamu; Kadoya, Masumi

2001-10-01

The purpose of this study was to investigate the effectiveness of dynamic MRI for diagnosing pericicatricial minimal residual breast cancer following excisional biopsy. Twenty-six patients who underwent excisional biopsy of a tumor or calcified lesion of the breast underwent gadolinium-enhanced dynamic MRI by the fat-saturated 2D fast spoiled gradient echo (SPGR) sequence (group 1), 24 patients by the spectral IR enhanced 3D fast gradient echo (Efgre3d) sequence (group 2). Pericicatricial residual cancer was confirmed histologically in 29 of the 50 patients. The overall sensitivity, specificity, accuracy, positive predictive value, and negative predictive value of MRI for residual cancer diagnosis was 66, 81, 72, 83 and 63%. A nodular, thick and discontinuous enhanced rim around the scar is indicative of a residual tumor. However, false-positive findings due to granulation or proliferative fibrocystic change remain limitations.

Improving material and energy recovery from the sewage sludge and biomass residues

International Nuclear Information System (INIS)

Kliopova, Irina; Makarskienė, Kristina

2015-01-01

Highlights: • SRF production from 10–40 mm fraction of pre-composted sludge and biomass residues. • The material and energy balance of compost and SRF production. • Characteristics of raw materials and classification of produced SRF. • Results of the efficiency of energy recovery, comparison analysis with – sawdust. - Abstract: Sewage sludge management is a big problem all over the world because of its large quantities and harmful impact on the environment. Energy conversion through fermentation, compost production from treated sludge for agriculture, especially for growing energetic plants, and treated sludge use for soil remediation are widely used alternatives of sewage sludge management. Recently, in many EU countries the popularity of these methods has decreased due to the sewage sludge content (heavy metals, organic pollutions and other hazards materials). This paper presents research results where the possibility of solid recovered fuel (SRF) production from the separate fraction (10–40 mm) of pre-composted materials – sewage sludge from municipal waste water treatment plant and biomass residues has been evaluated. The remaining fractions of pre-composted materials can be successfully used for compost or fertiliser production, as the concentration of heavy metals in the analysed composition is reduced in comparison with sewage sludge. During the experiment presented in this paper the volume of analysed biodegradable waste was reduced by 96%: about 20% of input biodegradable waste was recovered to SRF in the form of pellets with 14.25 MJ kg −1 of the net calorific value, about 23% were composted, the rest – evaporated and discharged in a wastewater. The methods of material-energy balances and comparison analysis of experiment data have been chosen for the environmental impact assessment of this biodegradable waste management alternative. Results of the efficiency of energy recovery from sewage sludge by SRF production and burning

Improving material and energy recovery from the sewage sludge and biomass residues

Energy Technology Data Exchange (ETDEWEB)

Kliopova, Irina, E-mail: irina.kliopova@ktu.lt; Makarskienė, Kristina

2015-02-15

Highlights: • SRF production from 10–40 mm fraction of pre-composted sludge and biomass residues. • The material and energy balance of compost and SRF production. • Characteristics of raw materials and classification of produced SRF. • Results of the efficiency of energy recovery, comparison analysis with – sawdust. - Abstract: Sewage sludge management is a big problem all over the world because of its large quantities and harmful impact on the environment. Energy conversion through fermentation, compost production from treated sludge for agriculture, especially for growing energetic plants, and treated sludge use for soil remediation are widely used alternatives of sewage sludge management. Recently, in many EU countries the popularity of these methods has decreased due to the sewage sludge content (heavy metals, organic pollutions and other hazards materials). This paper presents research results where the possibility of solid recovered fuel (SRF) production from the separate fraction (10–40 mm) of pre-composted materials – sewage sludge from municipal waste water treatment plant and biomass residues has been evaluated. The remaining fractions of pre-composted materials can be successfully used for compost or fertiliser production, as the concentration of heavy metals in the analysed composition is reduced in comparison with sewage sludge. During the experiment presented in this paper the volume of analysed biodegradable waste was reduced by 96%: about 20% of input biodegradable waste was recovered to SRF in the form of pellets with 14.25 MJ kg{sup −1} of the net calorific value, about 23% were composted, the rest – evaporated and discharged in a wastewater. The methods of material-energy balances and comparison analysis of experiment data have been chosen for the environmental impact assessment of this biodegradable waste management alternative. Results of the efficiency of energy recovery from sewage sludge by SRF production and burning

Natural hazards science strategy

Science.gov (United States)

Holmes, Robert R.; Jones, Lucile M.; Eidenshink, Jeffery C.; Godt, Jonathan W.; Kirby, Stephen H.; Love, Jeffrey J.; Neal, Christina A.; Plant, Nathaniel G.; Plunkett, Michael L.; Weaver, Craig S.; Wein, Anne; Perry, Suzanne C.

2012-01-01

The mission of the U.S. Geological Survey (USGS) in natural hazards is to develop and apply hazard science to help protect the safety, security, and economic well-being of the Nation. The costs and consequences of natural hazards can be enormous, and each year more people and infrastructure are at risk. USGS scientific research—founded on detailed observations and improved understanding of the responsible physical processes—can help to understand and reduce natural hazard risks and to make and effectively communicate reliable statements about hazard characteristics, such as frequency, magnitude, extent, onset, consequences, and where possible, the time of future events.To accomplish its broad hazard mission, the USGS maintains an expert workforce of scientists and technicians in the earth sciences, hydrology, biology, geography, social and behavioral sciences, and other fields, and engages cooperatively with numerous agencies, research institutions, and organizations in the public and private sectors, across the Nation and around the world. The scientific expertise required to accomplish the USGS mission in natural hazards includes a wide range of disciplines that this report refers to, in aggregate, as hazard science.In October 2010, the Natural Hazards Science Strategy Planning Team (H–SSPT) was charged with developing a long-term (10-year) Science Strategy for the USGS mission in natural hazards. This report fulfills that charge, with a document hereinafter referred to as the Strategy, to provide scientific observations, analyses, and research that are critical for the Nation to become more resilient to natural hazards. Science provides the information that decisionmakers need to determine whether risk management activities are worthwhile. Moreover, as the agency with the perspective of geologic time, the USGS is uniquely positioned to extend the collective experience of society to prepare for events outside current memory. The USGS has critical statutory

Radiation hazards

International Nuclear Information System (INIS)

Rausch, L.

1979-01-01

On a scientific basis and with the aid of realistic examples, the author gives a popular introduction to an understanding and judgment of the public discussion over radiation hazards: Uses and hazards of X-ray examinations, biological radiation effects, civilisation risks in comparison, origins and explanation of radiation protection regulations. (orig.) [de

The Scientific Management of Hazardous Wastes

Science.gov (United States)

Porter, Keith S.

According to the jacket of this book, three independent scientists carefully define the limits of scientific knowledge applicable to the management of hazardous wastes. It is claimed that the extrapolation and application of this knowledge is examined, significant areas of uncertainty are identified, and the authors reveal “the fallibility of certain interpretations.” It would be more accurate to claim these as possible goals of the book rather than its accomplishments.Chapter 1, Hazardous Wastes and Their Recycling Potential, includes 11 pages of lists of chemicals, some of which are poorly reproduced. The remaining pages describe, superficially, several recycling schemes. Connections between the chemicals previously listed and the recycling schemes are not given. Concerning the potential for recycling, the last sentence of the chapter reads, “Indeed, the concept of waste recycling, itself a contradiction in terms, is better politics than business.” Taken literally, this assertion itself contradicts venerable practice, as the farmer might observe as he transfers waste from his cows to the crops in his field. More pertinently, it can be argued that the recovery of solvents, metals, and oil from waste flows is much more than a political gesture.

Anglesite and silver recovery from jarosite residues through roasting and sulfidization-flotation in zinc hydrometallurgy

Energy Technology Data Exchange (ETDEWEB)

Han, Haisheng; Sun, Wei, E-mail: hanhaishengjingji@126.com; Hu, Yuehua; Jia, Baoliang; Tang, Honghu

2014-08-15

Highlights: • Jarosite precipitate hindered the recovery of valuable minerals. • Under 600–700 °C, jarosite decomposed and released the encapsulated valuable minerals. • The bared valuable minerals were easily collected by flotation process. • The new process was promising for dealing with jarosite residues. - Abstract: Hazardous jarosite residues contain abundant valuable minerals that are difficult to be recovered by traditional flotation process. This study presents a new route, roasting combined with sulfidization-flotation, for the recovery of anglesite and silver from jarosite residues of zinc hydrometallurgy. Surface appearance and elemental distribution of jarosite residues was examined by scanning electron microscopy and energy dispersive X-ray spectrometry analysis, respectively. Decomposition and transformation mechanisms of jarosite residues were illustrated by differential thermal analysis. Results showed that after roasting combined with flotation, the grade and recovery of lead were 43.89% and 66.86%, respectively, and those of silver were 1.3 kg/t and 81.60%, respectively. At 600–700 °C, jarosite was decomposed to release encapsulated valuable minerals such as anglesite (PbSO{sub 4}) and silver mineral; silver jarosite decomposed into silver sulfate (Ag{sub 2}SO{sub 4}); and zinc ferrite (ZnO·Fe{sub 2}O{sub 3}) decomposed into zinc sulfate (ZnSO{sub 4}) and hematite (Fe{sub 2}O{sub 3}). Bared anglesite and silver minerals were modified by sodium sulfide and easily collected by flotation collectors. This study demonstrates that the combination of roasting and sulfidization-flotation provides a promising process for the recovery of zinc, lead, and silver from jarosite residues of zinc hydrometallurgy.

Hazard screening application guide

International Nuclear Information System (INIS)

1992-06-01

The basic purpose of hazard screening is to group precesses, facilities, and proposed modifications according to the magnitude of their hazards so as to determine the need for and extent of follow on safety analysis. A hazard is defined as a material, energy source, or operation that has the potential to cause injury or illness in human beings. The purpose of this document is to give guidance and provide standard methods for performing hazard screening. Hazard screening is applied to new and existing facilities and processes as well as to proposed modifications to existing facilities and processes. The hazard screening process evaluates an identified hazards in terms of the effects on people, both on-site and off-site. The process uses bounding analyses with no credit given for mitigation of an accident with the exception of certain containers meeting DOT specifications. The process is restricted to human safety issues only. Environmental effects are addressed by the environmental program. Interfaces with environmental organizations will be established in order to share information

Software safety hazard analysis

International Nuclear Information System (INIS)

Lawrence, J.D.

1996-02-01

Techniques for analyzing the safety and reliability of analog-based electronic protection systems that serve to mitigate hazards in process control systems have been developed over many years, and are reasonably well understood. An example is the protection system in a nuclear power plant. The extension of these techniques to systems which include digital computers is not well developed, and there is little consensus among software engineering experts and safety experts on how to analyze such systems. One possible technique is to extend hazard analysis to include digital computer-based systems. Software is frequently overlooked during system hazard analyses, but this is unacceptable when the software is in control of a potentially hazardous operation. In such cases, hazard analysis should be extended to fully cover the software. A method for performing software hazard analysis is proposed in this paper

Mapping and quantification of organic agro-industrial residues in East Africa

Energy Technology Data Exchange (ETDEWEB)

Jungersen, G. [Dansk Teknologisk Inst. (Denmark); Kivaisi, A.; Rubindamayugi, M. [Univ. of Dar es Salaam (Tanzania, United Republic of)

1998-05-01

The East-African agro-industries generate very large quantities of organic residues from production and processing of different crops. These residues form a major contribution to the pollution of air, soil and water ways, but, at the same time they constitute a large potential for production of bioenergy through anaerobic digestion as well as potential substrate for other biological fermentation processes. The utilization of these resources for production of valuable products would contribute significantly to: Improvement of the local energy supply, through production of bio-energy; Improvement of the economy of the East African agro-industry; Reduction of the environmental impact from the agro-industrial sector. Except for production of cane sugar, most agro-industrial residues are generated from cash crops, which are produced and processed in the developing countries and where the final products mainly are used for export. In the East-African Region the most important of these crops are: Sisal, coffee, Cashew nuts and Pineapple. In addition significant quantities of organic residues are generated from other food processing activities like breweries, consumption of bananas etc. The total potential methane production of the residues available for use in biomethanization systems in East Africa is 189.61 million m{sup 3} of methane per year. Converted to diesel oil equivalents and including the residues only feasible for combustion systems, the total bioenergy potential of agro-industrial residues in Eastern Africa is 279,176 TOE. If this potential was fully utilized for production of electricity, it would correspond to installed effects of 37,68 and 31 MW in Tanzania, Kenya and Uganda, respectively, equivalent to 10%, 11% and 18% of the currently installed effect is these countries. Residues from sisal and coffee processing constitute the main part of the bioenergy potential, on average approximately 75%, while the remaining 25% of the potential are formed by the

Evaluation of residue-residue contact predictions in CASP9

KAUST Repository

Monastyrskyy, Bohdan; Fidelis, Krzysztof; Tramontano, Anna; Kryshtafovych, Andriy

2011-01-01

This work presents the results of the assessment of the intramolecular residue-residue contact predictions submitted to CASP9. The methodology for the assessment does not differ from that used in previous CASPs, with two basic evaluation measures

Drug residues in urban water: A database for ecotoxicological risk management.

Science.gov (United States)

Destrieux, Doriane; Laurent, François; Budzinski, Hélène; Pedelucq, Julie; Vervier, Philippe; Gerino, Magali

2017-12-31

Human-use drug residues (DR) are only partially eliminated by waste water treatment plants (WWTPs), so that residual amounts can reach natural waters and cause environmental hazards. In order to properly manage these hazards in the aquatic environment, a database is made available that integrates the concentration ranges for DR, which cause adverse effects for aquatic organisms, and the temporal variations of the ecotoxicological risks. To implement this database for the ecotoxicological risk assessment (ERA database), the required information for each DR is the predicted no effect concentrations (PNECs), along with the predicted environmental concentrations (PECs). The risk assessment is based on the ratio between the PNECs and the PECs. Adverse effect data or PNECs have been found in the publicly available literature for 45 substances. These ecotoxicity test data have been extracted from 125 different sources. This ERA database contains 1157 adverse effect data and 287 PNECs. The efficiency of this ERA database was tested with a data set coming from a simultaneous survey of WWTPs and the natural environment. In this data set, 26 DR were searched for in two WWTPs and in the river. On five sampling dates, concentrations measured in the river for 10 DR could pose environmental problems of which 7 were measured only downstream of WWTP outlets. From scientific literature and measurements, data implementation with unit homogenisation in a single database facilitates the actual ecotoxicological risk assessment, and may be useful for further risk coming from data arising from the future field survey. Moreover, the accumulation of a large ecotoxicity data set in a single database should not only improve knowledge of higher risk molecules but also supply an objective tool to help the rapid and efficient evaluation of the risk. Copyright © 2017 Elsevier B.V. All rights reserved.

Research and Development for Health and Environmental Hazard Assessment -Task Order 2. Problem Definition of R and D Requirements for Field Sanitation and Water Supply.

Science.gov (United States)

1982-09-01

34Development of a Kit for Hazardous Material Spills into Waterways," Edgewood Arsenal Special Publication ED- SP - 76023, 1976. Department of the Army...hepatitis, entamoeba hystolitica are more resistant and require free available chlorine residuals of 10 mg/l in cold weather and levels of 2, 5, 10

The Relationship Between Low-Frequency Motions and Community Structure of Residue Network in Protein Molecules.

Science.gov (United States)

Sun, Weitao

2018-01-01

The global shape of a protein molecule is believed to be dominant in determining low-frequency deformational motions. However, how structure dynamics relies on residue interactions remains largely unknown. The global residue community structure and the local residue interactions are two important coexisting factors imposing significant effects on low-frequency normal modes. In this work, an algorithm for community structure partition is proposed by integrating Miyazawa-Jernigan empirical potential energy as edge weight. A sensitivity parameter is defined to measure the effect of local residue interaction on low-frequency movement. We show that community structure is a more fundamental feature of residue contact networks. Moreover, we surprisingly find that low-frequency normal mode eigenvectors are sensitive to some local critical residue interaction pairs (CRIPs). A fair amount of CRIPs act as bridges and hold distributed structure components into a unified tertiary structure by bonding nearby communities. Community structure analysis and CRIP detection of 116 catalytic proteins reveal that breaking up of a CRIP can cause low-frequency allosteric movement of a residue at the far side of protein structure. The results imply that community structure and CRIP may be the structural basis for low-frequency motions.

Organochlorine and organophosphorus pesticide residues in fodder and milk samples along Musi river belt, India

Directory of Open Access Journals (Sweden)

Korrapati Kotinagu

2015-04-01

Full Text Available Aim: The present study was conducted to find the organochlorine pesticide (OCP and organophosphorus pesticide (OPP residues in fodder and milk samples along Musi river belt, India. Materials and Methods: Fodder and milk samples collected from the six zones of Musi river belt, Hyderabad India were analyzed by gas chromatography with electron capture detector for OCP residues and pulsated flame photometric detector for the presence of OPP residues. Results: The gas chromatographic analysis of fodder samples of Zone 5 of Musi river showed the residues of dicofol at concentration of 0.07±0.0007 (0.071-0.077. Among organophosphorus compounds, dimetheoate was present in milk samples collected from Zone 6 at a level of 0.13±0.006 (0.111-0.167. The residues of OCPs, OPPs and cyclodies were below the detection limit in the remaining fodder and milk samples collected from Musi river belt in the present study. Conclusion: The results indicate that the pesticide residues in fodder and milk samples were well below the maximum residue level (MRL values, whereas dicofol in fodder and dimethoate in milk were slightly above the MRL values specified by EU and CODEX.

Organochlorine and organophosphorus pesticide residues in fodder and milk samples along Musi river belt, India.

Science.gov (United States)

Kotinagu, Korrapati; Krishnaiah, Nelapati

2015-04-01

The present study was conducted to find the organochlorine pesticide (OCP) and organophosphorus pesticide (OPP) residues in fodder and milk samples along Musi river belt, India. Fodder and milk samples collected from the six zones of Musi river belt, Hyderabad India were analyzed by gas chromatography with electron capture detector for OCP residues and pulsated flame photometric detector for the presence of OPP residues. The gas chromatographic analysis of fodder samples of Zone 5 of Musi river showed the residues of dicofol at concentration of 0.07±0.0007 (0.071-0.077). Among organophosphorus compounds, dimetheoate was present in milk samples collected from Zone 6 at a level of 0.13±0.006 (0.111-0.167). The residues of OCPs, OPPs and cyclodies were below the detection limit in the remaining fodder and milk samples collected from Musi river belt in the present study. The results indicate that the pesticide residues in fodder and milk samples were well below the maximum residue level (MRL) values, whereas dicofol in fodder and dimethoate in milk were slightly above the MRL values specified by EU and CODEX.

Job Hazard Analysis

National Research Council Canada - National Science Library

1998-01-01

.... Establishing proper job procedures is one of the benefits of conducting a job hazard analysis carefully studying and recording each step of a job, identifying existing or potential job hazards...

Is residual memory variance a valid method for quantifying cognitive reserve? A longitudinal application

Science.gov (United States)

Zahodne, Laura B.; Manly, Jennifer J.; Brickman, Adam M.; Narkhede, Atul; Griffith, Erica Y.; Guzman, Vanessa A.; Schupf, Nicole; Stern, Yaakov

2016-01-01

Cognitive reserve describes the mismatch between brain integrity and cognitive performance. Older adults with high cognitive reserve are more resilient to age-related brain pathology. Traditionally, cognitive reserve is indexed indirectly via static proxy variables (e.g., years of education). More recently, cross-sectional studies have suggested that reserve can be expressed as residual variance in episodic memory performance that remains after accounting for demographic factors and brain pathology (whole brain, hippocampal, and white matter hyperintensity volumes). The present study extends these methods to a longitudinal framework in a community-based cohort of 244 older adults who underwent two comprehensive neuropsychological and structural magnetic resonance imaging sessions over 4.6 years. On average, residual memory variance decreased over time, consistent with the idea that cognitive reserve is depleted over time. Individual differences in change in residual memory variance predicted incident dementia, independent of baseline residual memory variance. Multiple-group latent difference score models revealed tighter coupling between brain and language changes among individuals with decreasing residual memory variance. These results suggest that changes in residual memory variance may capture a dynamic aspect of cognitive reserve and could be a useful way to summarize individual cognitive responses to brain changes. Change in residual memory variance among initially non-demented older adults was a better predictor of incident dementia than residual memory variance measured at one time-point. PMID:26348002

Analysis of shot-peening and residual stress relaxation in the nickel-based superalloy RR1000

International Nuclear Information System (INIS)

Foss, B.J.; Gray, S.; Hardy, M.C.; Stekovic, S.; McPhail, D.S.; Shollock, B.A.

2013-01-01

This work assesses the residual stress relaxation of the nickel-based alloy RR1000 due to thermal exposure and dwell-fatigue loading. A number of different characterization methods, including X-ray residual stress analysis, electron back-scattered diffraction, microhardness testing and focused ion beam secondary electron imaging, contributed to a detailed study of the shot-peened region. Thermal exposure at 700 °C resulted in a large reduction in the residual stresses and work-hardening effects in the alloy, but the subsurface remained in a beneficial compressive state. Oxidizing environments caused recrystallization in the near surface, but did not affect the residual stress-relaxation behaviour. Dwell-fatigue loading caused the residual stresses to return to approximately zero at nearly all depths. This work forms part of an ongoing investigation to determine the effects of shot-peening in this alloy with the motivation to improve the fatigue and oxidation resistance at 700 °C

Non-destructive measurement of residual stresses in U-0.8 wt.% Ti by neutron diffraction

International Nuclear Information System (INIS)

Salinas-Rodriguez, A.; Root, J.H.; Holden, T.M.; Macewen, S.R.; Ludtka, G.M.

1990-01-01

The macroscopic residual stress distribution in γ-quenched and stress levelled U-0.8wt% Ti alloy tubes was studied using neutron diffraction techniques. Residual strains were evaluated from the difference in d-spacings measured in the tubes and in small reference samples machined from each tube. Residual stresses were calculated with the isotropic bulk value of the elastic constraints for polycrystalline α-U. Quenching from the γ field resulted in a nearly equi-biaxial stress state at every point across the wall thickness of the tube. The magnitude of the radial stress was very small compared with that of the axial and hoop stresses which were compressive at the surfaces and tensile in the interior. Stress levelling relieved almost completely the hoop residual stress without affecting the radial stress. The axial residual stress becomes tensile through the wall thickness and remains constant at about 20% of its magnitude in the as-quenched condition

Introduction: Hazard mapping

Science.gov (United States)

Baum, Rex L.; Miyagi, Toyohiko; Lee, Saro; Trofymchuk, Oleksandr M

2014-01-01

Twenty papers were accepted into the session on landslide hazard mapping for oral presentation. The papers presented susceptibility and hazard analysis based on approaches ranging from field-based assessments to statistically based models to assessments that combined hydromechanical and probabilistic components. Many of the studies have taken advantage of increasing availability of remotely sensed data and nearly all relied on Geographic Information Systems to organize and analyze spatial data. The studies used a range of methods for assessing performance and validating hazard and susceptibility models. A few of the studies presented in this session also included some element of landslide risk assessment. This collection of papers clearly demonstrates that a wide range of approaches can lead to useful assessments of landslide susceptibility and hazard.

Biological treatment of concentrated hazardous, toxic, andradionuclide mixed wastes without dilution

Energy Technology Data Exchange (ETDEWEB)

Stringfellow, William T.; Komada, Tatsuyuki; Chang, Li-Yang

2004-06-15

Approximately 10 percent of all radioactive wastes produced in the U. S. are mixed with hazardous or toxic chemicals and therefore can not be placed in secure land disposal facilities. Mixed wastes containing hazardous organic chemicals are often incinerated, but volatile radioactive elements are released directly into the biosphere. Some mixed wastes do not currently have any identified disposal option and are stored locally awaiting new developments. Biological treatment has been proposed as a potentially safer alternative to incineration for the treatment of hazardous organic mixed wastes, since biological treatment would not release volatile radioisotopes and the residual low-level radioactive waste would no longer be restricted from land disposal. Prior studies have shown that toxicity associated with acetonitrile is a significant limiting factor for the application of biotreatment to mixed wastes and excessive dilution was required to avoid inhibition of biological treatment. In this study, we demonstrate that a novel reactor configuration, where the concentrated toxic waste is drip-fed into a complete-mix bioreactor containing a pre-concentrated active microbial population, can be used to treat a surrogate acetonitrile mixed waste stream without excessive dilution. Using a drip-feed bioreactor, we were able to treat a 90,000 mg/L acetonitrile solution to less than 0.1 mg/L final concentration using a dilution factor of only 3.4. It was determined that the acetonitrile degradation reaction was inhibited at a pH above 7.2 and that the reactor could be modeled using conventional kinetic and mass balance approaches. Using a drip-feed reactor configuration addresses a major limiting factor (toxic inhibition) for the biological treatment of toxic, hazardous, or radioactive mixed wastes and suggests that drip-feed bioreactors could be used to treat other concentrated toxic waste streams, such as chemical warfare materiel.

Can Chlorella pyrenoidosa be a bioindicator for hazardous solid waste detoxification?

Energy Technology Data Exchange (ETDEWEB)

Hu, Li-Fang, E-mail: hulif127@163.com [College of Quality and Safety Engineering, China Jiliang University, Hangzhou 310018 (China); Long, Yu-Yang; Shen, Dong-Sheng [School of Environmental Science and Engineering, Zhejiang Gongshang University, Hangzhou 310012 (China); Jiang, Chen-Jing [The Second Institute of Oceanography, SOA, Hangzhou 310012 (China)

2012-02-01

Four kinds of solid waste residue (SWR, S1 to S4) from different stages in a sequential detoxification process were chosen. The biotoxicity of the leachates from S1 to S4 was tested by Chlorella pyrenoidosa. The growth inhibition, the chlorophyll a (chla) and chlorophyll b (chlb) concentrations, and the ultrastructural morphology of cells of C. pyrenoidosa were studied. It shows that the growth inhibition of C. pyrenoidosa significantly increased with increasing leachate concentration when exposed to the leachates from S1, S2, S3, and S4, respectively. It well reflects the toxicity difference of leachate from SWR at different treatment stages, namely S1 > S2 > S3 > S4. Correspondingly, the chla and chlb concentrations of C. pyrenoidosa increased gradually as SWR was treated deeply. Leachate disrupted chlorophyll synthesis and inhibited cell growth. The changing of the ultrastructural morphology of cells under different leachate exposures, such as volume of chloroplasts and quantity of thylakoids reducing, confirmed the toxicity decrease of leachates from different stages. C. pyrenoidosa is a good bioindicator for hazardous solid waste detoxification. The EC{sub 50} at difference scenarios also suggests that it was feasible to estimate ecological toxicity of leachates to C. pyrenoidosa after exposure times of 72 h. C. pyrenoidosa can be introduced to evaluate the effect of hazardous solid waste disposal by biotoxicity assessment. - Highlights: Black-Right-Pointing-Pointer The detoxification process of hazardous solid waste was evaluated by Chlorella pyrenoidosa. Black-Right-Pointing-Pointer The best exposure time of ecological toxicity assessment of Chlorella pyrenoidosa was presented. Black-Right-Pointing-Pointer The possible toxicity of the hazardous solid waste at different disposal stage on Chlorella pyrenoidosa was explored from cell tissue.

Residual Stresses in a NiCrY-Coated Powder Metallurgy Disk Superalloy

Science.gov (United States)

Gabb, Timothy P.; Rogers, Richard B.; Nesbitt, James A.; Puleo, Bernadette J.; Miller, Robert A.; Telesman, Ignacy; Draper, Susan L.; Locci, Ivan E.

2017-01-01

Protective ductile coatings will be necessary to mitigate oxidation and corrosion attack on superalloy disks exposed to increasing operating temperatures in some turbine engine environments. However, such coatings must be resistant to harmful surface cracking during service. The objective of this study was to investigate how residual stresses evolve in such coatings. Cylindrical gage fatigue specimens of powder metallurgy-processed disk superalloy LSHR were coated with a NiCrY coating, shot peened, and then subjected to fatigue in air at room and high temperatures. The effects of shot peening and fatigue cycling on average residual stresses and other aspects of the coating were assessed. Shot peening did induce beneficial compressive residual stresses in the coating and substrate. However, these stresses became more tensile in the coating with subsequent heating and contributed to cracking of the coating in long intervals of cycling at 760 C. Substantial compressive residual stresses remained in the substrate adjacent to the coating, sufficient to suppress fatigue cracking. The coating continued to protect the substrate from hot corrosion pitting, even after fatigue cracks initiated in the coating.

Exposure assessment of chemical hazards in pork meat, liver, and kidney, and health impact implication in Hung Yen and Nghe An provinces, Vietnam.

Science.gov (United States)

Tuyet-Hanh, Tran Thi; Sinh, Dang Xuan; Phuc, Pham Duc; Ngan, Tran Thi; Van Tuat, Chu; Grace, Delia; Unger, Fred; Nguyen-Viet, Hung

2017-02-01

This study assesses the risk of exposure to hazardous chemical residues in pork meat, liver, and kidney collected at wet markets in Nghe An and Hung Yen provinces and discusses health impact implication. 514 pig feed, kidney, liver, and pork samples were pooled and qualitatively and quantitatively analyzed for tetracyclines, fluoroquinolones, sulphonamide, chloramphenicol, β-agonists, and heavy metals. We compare the results with current regulations on chemical residues and discuss health implications. Legal antibiotics were found in feed. Tetracycline and fluoroquinolones were not present in pork, but 11% samples were positive with sulfamethazine above maximum residue limits (MRL); 11% of packaged feed and 4% of pork pooled samples were positive for chloramphenicol, a banned substance; two feed, two liver, and one pork samples were positive for β-agonists but did not exceed current MRL; 28% of pooled samples had lead, but all were below MRL; and all samples were negative for cadmium and arsenic. Thus, the health risks due to chemical hazards in pork in Hung Yen and Nghe An seemed not as serious as what were recently communicated to the public on the mass media. There is potential exposure to sulphonamide, chloramphenicol, and β-agonists from pork. Risk communication needs to focus on banned chemicals, while informing the public about the minimal risks associated with heavy metals.

Opportunities and Barriers to Resource Recovery and Recycling from Shredder Residue in the United States

Science.gov (United States)

Nayak, Naren; Apelian, Diran

2014-11-01

Shredder residue is the by-product remaining after ferrous and nonferrous metals have been recovered from the processing of vehicles, white goods, and peddler scrap. Shredder residue consists of glass, plastics, rubber, dirt, and small amounts of metal. It is estimated that 5-7 million tons of this shredder residue are landfilled each year in the United States. Technical advancements, coupled with European Union directives and the economic climate, have transformed the recycling of shredder residue in Europe. In the United States, however, regulatory controls and the cheap cost of landfill have worked against the advancement of recycling and recovery of this resource. The Argonne National Laboratory, which is funded by the U.S. Department of Energy, has investigated the effectiveness of recycling shredder residue into polymers. Other research has examined the use of shredder residue in waste-to-energy applications. To improve our ability to process and recycle shredder residue, an investigation of the regulatory, economic, and technological challenges was undertaken. The objective was to conduct a comprehensive review of work done to date, to document the composition of typical shredder output and to identify potential recoverable items (residual metals, plastics, rubber, foam, etc.). Along with uncovering potential new markets, the research would identify the technical, regulatory, and economic barriers to developing those markets.

Aflatoxin B1 residues in imported and local broiler, s breast and thigh muscle in Kurdistan region

Directory of Open Access Journals (Sweden)

E.P. Candlan

2015-06-01

Full Text Available Residues of Aflatoxins and their metabolites might be present in meat and other products of animals receiving Aflatoxin contaminated feeds which could subsequently create health problems in man. Eighty nine imported (Iran/Khosh pokht; (Turkey/Yam-tapilic, Lades, Senplic, Kapidac, Kozoa, Oznesilpilic and (Brazil, hilal, Sadia, and 90 locally produced (Hoshiar poultry farm, Nihad poultry farm, Hokar poultry farm, Mansoor poultry farm, AL-Shimal poultry house, Mardin poultry house and AL-Eetimad poultry slaughterhouse broiler breast and thigh muscle samples were examined for residual Aflatoxin B1 using ELIZA test. Results revealed that out of 89 imported samples only 21 (23.59% were positive, but only 2 (2.24% were rejected, while the remaining 87 samples (97.75% were acceptable. Concerning the local samples, results showed that 19 samples (21.11% were positive, but 10 (11.11% were rejected, while the remaining 80 samples (88.88% were accepted. The public health importance of residual AFB1 in broiler meat samples was discussed.

Tyrosine Residues Regulate Multiple Nuclear Functions of P54nrb.

Science.gov (United States)

Lee, Ahn R; Hung, Wayne; Xie, Ning; Liu, Liangliang; He, Leye; Dong, Xuesen

2017-04-01

The non-POU-domain-containing octamer binding protein (NONO; also known as p54nrb) has various nuclear functions ranging from transcription, RNA splicing, DNA synthesis and repair. Although tyrosine phosphorylation has been proposed to account for the multi-functional properties of p54nrb, direct evidence on p54nrb as a phosphotyrosine protein remains unclear. To investigate the tyrosine phosphorylation status of p54nrb, we performed site-directed mutagenesis on the five tyrosine residues of p54nrb, replacing the tyrosine residues with phenylalanine or alanine, and immunoblotted for tyrosine phosphorylation. We then preceded with luciferase reporter assays, RNA splicing minigene assays, co-immunoprecipitation, and confocal microscopy to study the function of p54nrb tyrosine residues on transcription, RNA splicing, protein-protein interaction, and cellular localization. We found that p54nrb was not phosphorylated at tyrosine residues. Rather, it has non-specific binding affinity to anti-phosphotyrosine antibodies. However, replacement of tyrosine with phenylalanine altered p54nrb activities in transcription co-repression and RNA splicing in gene context-dependent fashions by means of differential regulation of p54nrb protein association with its interacting partners and co-regulators of transcription and splicing. These results demonstrate that tyrosine residues, regardless of phosphorylation status, are important for p54nrb function. J. Cell. Physiol. 232: 852-861, 2017. © 2016 Wiley Periodicals, Inc. © 2016 Wiley Periodicals, Inc.

International symposium on restoration of environments with radioactive residues. Contributed papers

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-07-01

After the use of radioactive materials or the utilization of nuclear energy, some radioactive residues may remain in the environment and give rise to the exposure of persons living or working in that environment. Most commonly, these residues are the result of human activities that have been carried out in the past without proper regard to the internationally accepted radiation protection requirements for practices, or at that time when those requirements were less stringent than today. Of course unforeseen events such as accidents of concentrations of naturally occurring radioactive material can also lead to higher levels of radioactive residues in theenvironment. The purpose of this Symposium is to foster an information exchange on the restoration of environments with radioactive residues. This includes the principles and criteria for guiding decision making and the methodologies for assessing the radiological situation and developing remediation plans for the human habitats affected. The overall aim is to promote an international consensus on the relevant issues in these areas. This document contains 51 presentations delivered during oral and poster sessions. Each of the presentations was separately indexed and provided with an abstract.

International symposium on restoration of environments with radioactive residues. Contributed papers

International Nuclear Information System (INIS)

1999-01-01

After the use of radioactive materials or the utilization of nuclear energy, some radioactive residues may remain in the environment and give rise to the exposure of persons living or working in that environment. Most commonly, these residues are the result of human activities that have been carried out in the past without proper regard to the internationally accepted radiation protection requirements for practices, or at that time when those requirements were less stringent than today. Of course unforeseen events such as accidents of concentrations of naturally occurring radioactive material can also lead to higher levels of radioactive residues in the environment. The purpose of this Symposium is to foster an information exchange on the restoration of environments with radioactive residues. This includes the principles and criteria for guiding decision making and the methodologies for assessing the radiological situation and developing remediation plans for the human habitats affected. The overall aim is to promote an international consensus on the relevant issues in these areas. This document contains 51 presentations delivered during oral and poster sessions. Each of the presentations was separately indexed and provided with an abstract

Barrow hazards survey

International Nuclear Information System (INIS)

1980-06-01

Following a series of public meetings at which PERG presented the results of a literature review and site specific accident study of the hazards of the maritime transport of spent nuclear reactor fuel to Barrow (en route to the Windscale reprocessing works), PERG was requested by the Planning Committee of Barrow Town Council to prepare an assessment of the interaction of the hazards arising from the concentration of nuclear activities in the area with those of a proposed gas-terminal. This report presents a preliminary review of the Environmental Impact Assessments prepared by the Borough Surveyor and a critical appraisal of the hazard analyses undertaken by the Health and Safety Executive, and the consultants to Cumbria County Council on this matter, the Safety and Reliability Directorate of the United Kingdom Atomic Energy Authority. After a general and historical introduction, the document continues under the following headings: a description of the hazards (BNFL spent fuel shipments; the gas terminal; gas condensate storage; the Vickers shipyard (involving nuclear powered submarines)); the interaction of hazards; planning implications and democratic decisions; recommendations. (U.K.)

Hazardous waste management system design under population and environmental impact considerations.

Science.gov (United States)

Yilmaz, Ozge; Kara, Bahar Y; Yetis, Ulku

2017-12-01

This paper presents a multi objective mixed integer location/routing model that aims to minimize transportation cost and risks for large-scale hazardous waste management systems (HWMSs). Risks induced by hazardous wastes (HWs) on both public and the environment are addressed. For this purpose, a new environmental impact definition is proposed that considers the environmentally vulnerable elements including water bodies, agricultural areas, coastal regions and forestlands located within a certain bandwidth around transportation routes. The solution procedure yields to Pareto optimal curve for two conflicting objectives. The conceptual model developed prior to mathematical formulation addresses waste-to-technology compatibility and HW processing residues to assure applicability of the model to real-life HWMSs. The suggested model was used in a case study targeting HWMS in Turkey. Based on the proposed solution, it was possible to identify not only the transportation routes but also a set of information on HW handling facilities including the types, locations, capacities, and investment/operational cost. The HWMS of this study can be utilized both by public authorities and private sector investors for planning purposes. Copyright © 2016 Elsevier Ltd. All rights reserved.

Effect of texture and grain size on the residual stress of nanocrystalline thin films

Science.gov (United States)

Cao, Lei; Sengupta, Arkaprabha; Pantuso, Daniel; Koslowski, Marisol

2017-10-01

Residual stresses develop in thin film interconnects mainly as a result of deposition conditions and multiple thermal loading cycles during the manufacturing flow. Understanding the relation between the distribution of residual stress and the interconnect microstructure is of key importance to manage the nucleation and growth of defects that can lead to failure under reliability testing and use conditions. Dislocation dynamics simulations are performed in nanocrystalline copper subjected to cyclic loading to quantify the distribution of residual stresses as a function of grain misorientation and grain size distribution. The outcomes of this work help to evaluate the effect of microstructure in thin films failure by identifying potential voiding sites. Furthermore, the simulations show how dislocation structures are influenced by texture and grain size distribution that affect the residual stress. For example, when dislocation loops reach the opposite grain boundary during loading, these dislocations remain locked during unloading.

Coping with residual stresses in the integrity assessment of an as-welded repair

International Nuclear Information System (INIS)

Knee, N.

1989-11-01

One of a series of large scale tests on pressure vessels is described, in which a defect was deliberately introduced into an as-welded (i.e. not stress relieved) repair weld. The behaviour of the vessel during pressurization to failure was carefully monitored and the actual performance compared with theoretical predictions. The influence of residual welding stresses on ductile crack growth from pre-existing defects is discussed in the light of the results of this test and of previous tests in the series. The tests have confirmed that residual stresses can exert a significant effect on the growth of fatigue cracks. However, in tests for which the failure mechanism is predominantly controlled by collapse of the remaining ligament, the development of plasticity during pressurization to failure will tend to remove any local residual stresses. (author)

Utility residual fuel oil market conditions: An update

International Nuclear Information System (INIS)

Mueller, H.A. Jr.

1992-01-01

Planning for residual fuel oil usage and management remains an important part of the generation fuel planning and management function for many utilities. EPRI's Utility Planning Methods Center has maintained its analytical overview of the fuel oil markets as part of its overall fuel planning and management research program. This overview provides an update of recent fuel oil market directions. Several key events of the past year have had important implications for residual fuel oil markets. The key events have been the changes brought about by the Persian Gulf War and its aftermath, as well as continuing environmental policy developments. The Persian Gulf conflict has created renewed interest in reducing fuel oil use by utilities as part of an overall reduction in oil imports. The policy analysis performed to date has generally failed to properly evaluate utility industry capability. The Persian Gulf conflict has also resulted in an important change in the structure of international oil markets. The result of this policy-based change is likely to be a shift in oil pricing strategy. Finally, continued change in environmental requirements is continuing to shift utility residual oil requirements, but is also changing the nature of the US resid market itself

76 FR 4823 - Hazardous Waste Management System; Identifying and Listing Hazardous Waste Exclusion

Science.gov (United States)

2011-01-27

... Waste Management System; Identifying and Listing Hazardous Waste Exclusion AGENCY: Environmental... hazardous wastes. The Agency has decided to grant the petition based on an evaluation of waste-specific... excludes the petitioned waste from the requirements of hazardous waste regulations under the Resource...

Structural comparison of hazardous and non-hazardous coals based on gas sorption experiments

Energy Technology Data Exchange (ETDEWEB)

Lakatos, J.; Toth, J. [Research Lab. for Mining Chemistry, Hungarian Academy of Sciences, Miskolc-Egyetemvaros (Hungary); Radnai-Gyoengyoes, Z. [Geopard Ltd., Pecs (Hungary); Bokanyi, L. [Miskolc Univ., Miskolc-Egyetemvaros (Hungary). Dept. of Process Engineering

1997-12-31

Comparison of carbon-dioxide and propane sorption at ambient temperature was used for characterising the difference of the structure of hazardous and non hazardous coals. However, hazardous coals were found more microporous or contain more closed pores than non hazardous ones, this difference couldn`t have been enlarged and attributed to one petrographic component by producing the density fractions. Gas sorption isobars (nitrogen, methane, ethane) are proposed to make a distinction between fine pore structure of coals. (orig.)

Bayesian network learning for natural hazard assessments

Science.gov (United States)

Vogel, Kristin

2016-04-01

Even though quite different in occurrence and consequences, from a modelling perspective many natural hazards share similar properties and challenges. Their complex nature as well as lacking knowledge about their driving forces and potential effects make their analysis demanding. On top of the uncertainty about the modelling framework, inaccurate or incomplete event observations and the intrinsic randomness of the natural phenomenon add up to different interacting layers of uncertainty, which require a careful handling. Thus, for reliable natural hazard assessments it is crucial not only to capture and quantify involved uncertainties, but also to express and communicate uncertainties in an intuitive way. Decision-makers, who often find it difficult to deal with uncertainties, might otherwise return to familiar (mostly deterministic) proceedings. In the scope of the DFG research training group „NatRiskChange" we apply the probabilistic framework of Bayesian networks for diverse natural hazard and vulnerability studies. The great potential of Bayesian networks was already shown in previous natural hazard assessments. Treating each model component as random variable, Bayesian networks aim at capturing the joint distribution of all considered variables. Hence, each conditional distribution of interest (e.g. the effect of precautionary measures on damage reduction) can be inferred. The (in-)dependencies between the considered variables can be learned purely data driven or be given by experts. Even a combination of both is possible. By translating the (in-)dependences into a graph structure, Bayesian networks provide direct insights into the workings of the system and allow to learn about the underlying processes. Besides numerous studies on the topic, learning Bayesian networks from real-world data remains challenging. In previous studies, e.g. on earthquake induced ground motion and flood damage assessments, we tackled the problems arising with continuous variables

[Situation analysis and standard formulation of pesticide residues in traditional Chinese medicines].

Science.gov (United States)

Yang, Wan-Zhen; Kang, Chuan-Zhi; Ji, Rui-Feng; Zhou, L I; Wang, Sheng; Li, Zhen-Hao; Ma, Zhong-Hua; Guo, Lan-Ping

2017-06-01

Chinese Pharmacopoeia provides nine pesticide Maximum Residual Limits(MRLs) of traditional Chinese medicines(TCMs), The number of pesticides used in production are far more than those listed in pharmacopoeia. The lack of the standards make it's hard to reflect the real situation of pesticide residues in TCMs correctly. The paper is aimed to analyze the data of pesticide residues in TCMs from 7 089 items in 140 reports, and judging the exceedance rate of pesticides in TCMs using the MRLs of European pharmacopoeia，which is widely accepted in many countries. The results show that：①Pesticide residues in 18 kinds of TCMs are higher than MRLs，while in 137 kinds are below MRLs, such as Atractylodis Macrocephalae Rhizoma, Menthae Haplocalycis Herba and Fritillariae Thunbergii Bulbus. The average exceedance rate of all TCMs is 1.72%. The average exceedance rates of organochlorine, organophosphorus and pyrethroid are 2.26%, 1.51%, 0.37%，respectively. ②The average exceedance rate of pesticides is 2.00%, and the exceedance rate is more than 5%, accounting for 8.33%, the exceedance rate is between 1%-5%, accounting for 18.75%. the exceedance rate is between 0%-1%, accounting for 18.75%. The remaining 29 kinds of pesticides were not exceeded, accounting for 60.42%.Some reports like Greenpeace's organization exaggerated the pesticide residues in TCMs.But the pesticide residue question is still worthy of attention, so we proposed to amend the Chinese Pharmacopoeia pesticide residues standards, to increase the pesticide species of traditional Chinese medicine in production on the basis of retaining the existing types of pesticide residues, to strengthen the system research of pesticide residues in TCMs, providing a basis for making standard and promoting import and export trade in TCMs. Copyright© by the Chinese Pharmaceutical Association.

The use of permanganate as a sequencing reagent for identification of 5-methylcytosine residues in DNA.

OpenAIRE

Fritzsche, E; Hayatsu, H; Igloi, G L; Iida, S; Kössel, H

1987-01-01

The use of permanganate as a reagent for DNA sequencing by chemical degradation has been studied with respect to its specificity for 5-methylcytosine residues. At weakly acidic pH and room temperature, 0.2 mM potassium permanganate reacts preferentially with thymine, 5-methylcytosine, and to a lesser extent with purine residues, while cytosine remains essentially intact. Permanganate oxidation is, therefore, a suitable DNA sequencing reaction for positive discrimination between 5-methylcytosi...

Informing Workers of Chemical Hazards: The OSHA Hazard Communication Standard.

Science.gov (United States)

American Chemical Society, Washington, DC.

Practical information on how to implement a chemical-related safety program is outlined in this publication. Highlights of the federal Occupational Safety and Health Administrations (OSHA) Hazard Communication Standard are presented and explained. These include: (1) hazard communication requirements (consisting of warning labels, material safety…

Transport of hazardous goods

International Nuclear Information System (INIS)

1989-01-01

The course 'Transport of hazardous goods' was held in Berlin in November 1988 in cooperation with the Bundesanstalt fuer Materialforschung und -pruefung. From all lecturs, two are recorded separately: 'Safety of tank trucks - requirements on the tank, development possibiities of active and passive safety' and 'Requirements on the transport of radioactive materials - possible derivations for other hazardous goods'. The other lectures deal with hazardous goods law, requirements on packinging, risk assessment, railroad transport, hazardous goods road network, insurance matters, EC regulations, and waste tourism. (HSCH) [de

Seismic hazard maps for Haiti

Science.gov (United States)

Frankel, Arthur; Harmsen, Stephen; Mueller, Charles; Calais, Eric; Haase, Jennifer

2011-01-01

We have produced probabilistic seismic hazard maps of Haiti for peak ground acceleration and response spectral accelerations that include the hazard from the major crustal faults, subduction zones, and background earthquakes. The hazard from the Enriquillo-Plantain Garden, Septentrional, and Matheux-Neiba fault zones was estimated using fault slip rates determined from GPS measurements. The hazard from the subduction zones along the northern and southeastern coasts of Hispaniola was calculated from slip rates derived from GPS data and the overall plate motion. Hazard maps were made for a firm-rock site condition and for a grid of shallow shear-wave velocities estimated from topographic slope. The maps show substantial hazard throughout Haiti, with the highest hazard in Haiti along the Enriquillo-Plantain Garden and Septentrional fault zones. The Matheux-Neiba Fault exhibits high hazard in the maps for 2% probability of exceedance in 50 years, although its slip rate is poorly constrained.

An ecotoxic risk assessment of residue materials produced by the plasma pyrolysis/vitrification (PP/V) process.

Science.gov (United States)

Lapa, N; Santos, Oliveira J F; Camacho, S L; Circeo, L J

2002-01-01

Plasma is the fourth state of matter, following the three states of solid, liquid and gas. Experience has amply demonstrated that solids exposed to the oxygen-deficient plasma flame are converted to liquid, and liquid exposed to the same flame is converted to gas. A low amount of vitrified solid residue material usually remains at the end of this process. Plasma pyrolysis/vitrification (PP/V) has been demonstrated as a safe, efficient, cost-effective technology for the treatment of wastes, including hazardous wastes. Besides the low amounts of gaseous byproducts that PP/V produces, the solid vitrified residue presents a low leachability of pollutants. Studies have been performed in many countries in order to assess the leachability of chemical substances. But from the results of identified studies, none has reported results on the ecotoxicological properties of the leachates. The aim of this study was to contribute to the assessment of ecotoxic risk of four different vitrified materials. Vitrified samples of contaminated soils, municipal solid wastes, and incinerator bottom ashes were submitted to the European leaching pre-standard test number prEN 12457-2. The leachates were analyzed for 22 chemical parameters. The biological characterization comprised the assessment of bioluminescence inhibition of Photobacterium phosphoreum bacterium, growth inhibition of Pseudokirchneriella subcapitata algae and the germination inhibition of Lactuca sativa vegetable. The chemical and ecotoxicological results were analyzed according to the French proposal of Criteria on the Evaluation Methods of Waste Toxicity (CEMWT) and a Toxicity Classification System (TCS). The chemical and ecotoxicological results indicated a low leachability of pollutants and a low toxicity level of leachates. All samples studied were as below the TCS class 1 level (no significant toxicity observed) and as non-ecotoxic for CEMWT. Therefore, the environmental ecotoxic risk of the analyzed vitrified samples

Rigid Residue Scan Simulations Systematically Reveal Residue Entropic Roles in Protein Allostery.

Directory of Open Access Journals (Sweden)

Robert Kalescky

2016-04-01

Full Text Available Intra-protein information is transmitted over distances via allosteric processes. This ubiquitous protein process allows for protein function changes due to ligand binding events. Understanding protein allostery is essential to understanding protein functions. In this study, allostery in the second PDZ domain (PDZ2 in the human PTP1E protein is examined as model system to advance a recently developed rigid residue scan method combining with configurational entropy calculation and principal component analysis. The contributions from individual residues to whole-protein dynamics and allostery were systematically assessed via rigid body simulations of both unbound and ligand-bound states of the protein. The entropic contributions of individual residues to whole-protein dynamics were evaluated based on covariance-based correlation analysis of all simulations. The changes of overall protein entropy when individual residues being held rigid support that the rigidity/flexibility equilibrium in protein structure is governed by the La Châtelier's principle of chemical equilibrium. Key residues of PDZ2 allostery were identified with good agreement with NMR studies of the same protein bound to the same peptide. On the other hand, the change of entropic contribution from each residue upon perturbation revealed intrinsic differences among all the residues. The quasi-harmonic and principal component analyses of simulations without rigid residue perturbation showed a coherent allosteric mode from unbound and bound states, respectively. The projection of simulations with rigid residue perturbation onto coherent allosteric modes demonstrated the intrinsic shifting of ensemble distributions supporting the population-shift theory of protein allostery. Overall, the study presented here provides a robust and systematic approach to estimate the contribution of individual residue internal motion to overall protein dynamics and allostery.

Aeromedical Hazard Comparison of FAA Medically Certified Third-Class and Medically Uncertified Pilots.

Science.gov (United States)

Ricaurte, Eduard M; Mills, William D; DeJohn, Charles A; Laverde-Lopez, Maria C; Porras-Sanchez, Daniel F

2016-07-01

Since 2004, in the United States, light sport aircraft (LSA) and some aircraft with standard airworthiness certificates can be operated for recreational purposes with a valid state driver's license rather than a Federal Aviation Administration (FAA)-issued aeromedical certificate. There have been recent efforts to allow operation of much larger, heavier, faster, and more complex aircraft without requiring a medical certificate. The primary objective of this research was to compare hazards to flight safety identified in fatally injured pilots required to possess a valid FAA third-class medical certificate to hazards in fatally injured pilots who were not required to possess a valid medical certificate. A search of all fatal U.S. aircraft accidents in the FAA Medical ANalysis and TRAcking (MANTRA) registry between January 1, 2011, and April 30, 2014, identified 1084 individuals. A review of accident pilots' medical, autopsy, and toxicological data was conducted. After applying exclusion criteria, 467 pilots remained, including 403 medically certified and 64 medically uncertified pilots. A significant difference was found in a surrogate measure for risk between medically certified and uncertified pilots (25% vs. 59%). This difference remained significant after adjustment for age. No significant difference was found in the proportions of hazards identified on toxicological review. The results of this study suggest that the risk of an adverse medical event is reduced in pilots required to possess a valid medical certificate. Ricaurte EM, Mills WD, DeJohn CA, Laverde-Lopez MC, Porras-Sanchez DF. Aeromedical hazard comparison of FAA medically certified third-class and medically uncertified pilots. Aerosp Med Hum Perform. 2016; 87(7):618-621.

INTERNAL HAZARDS ANALYSIS FOR LICENSE APPLICATION

Energy Technology Data Exchange (ETDEWEB)

R.J. Garrett

2005-02-17

The purpose of this internal hazards analysis is to identify and document the internal hazards and potential initiating events associated with preclosure operations of the repository at Yucca Mountain. Internal hazards are those hazards presented by the operation of the facility and by its associated processes that can potentially lead to a radioactive release or cause a radiological hazard. In contrast to external hazards, internal hazards do not involve natural phenomena and external man-made hazards. This internal hazards analysis was performed in support of the preclosure safety analysis and the License Application for the Yucca Mountain Project. The methodology for this analysis provides a systematic means to identify internal hazards and potential initiating events that may result in a radiological hazard or radiological release during the repository preclosure period. These hazards are documented in tables of potential internal hazards and potential initiating events (Section 6.6) for input to the repository event sequence categorization process. The results of this analysis will undergo further screening and analysis based on the criteria that apply to the performance of event sequence analyses for the repository preclosure period. The evolving design of the repository will be re-evaluated periodically to ensure that internal hazards that have not been previously evaluated are identified.

INTERNAL HAZARDS ANALYSIS FOR LICENSE APPLICATION

International Nuclear Information System (INIS)

Garrett, R.J.

2005-01-01

The purpose of this internal hazards analysis is to identify and document the internal hazards and potential initiating events associated with preclosure operations of the repository at Yucca Mountain. Internal hazards are those hazards presented by the operation of the facility and by its associated processes that can potentially lead to a radioactive release or cause a radiological hazard. In contrast to external hazards, internal hazards do not involve natural phenomena and external man-made hazards. This internal hazards analysis was performed in support of the preclosure safety analysis and the License Application for the Yucca Mountain Project. The methodology for this analysis provides a systematic means to identify internal hazards and potential initiating events that may result in a radiological hazard or radiological release during the repository preclosure period. These hazards are documented in tables of potential internal hazards and potential initiating events (Section 6.6) for input to the repository event sequence categorization process. The results of this analysis will undergo further screening and analysis based on the criteria that apply to the performance of event sequence analyses for the repository preclosure period. The evolving design of the repository will be re-evaluated periodically to ensure that internal hazards that have not been previously evaluated are identified

Heating oil, distillates and residuals outlook

International Nuclear Information System (INIS)

Ervin, M.J.

2004-01-01

M.J. Ervin and Associates offers strategic planning support to the downstream petroleum industry in terms of price market monitoring, market analysis, media commentary and benchmarking of marketing operations. This presentation included graphs depicting supply and demand for heating oil distillates and residuals from the mid 1990s to 2004. It was noted that the long-term decline in residuals demand in the United States and Canada are due to environmental issues, the use of natural gas as an alternative, and the increasing complexity of refineries. Graphs depicting market impacts of refinery utilization and inventory trends showed that middle distillate production will increase at the expense of gasoline production. Middle distillates and gasoline markets will be more sensitive to supply disruptions, resulting in more frequent price spikes. Inventory trends indicate a greater reliance on product imports. The demand for heating fuel has stabilized due to the continued penetration of natural gas in eastern states and provinces. The demand for diesel fuel has growth 1.5 to 2 per cent while the demand for jet fuel has remained relatively flat and depends greatly on the growth of the gross national product (GNP). tabs., figs

Remaining Sites Verification Package for the 100-F-33, 146-F Aquatic Biology Fish Ponds. Attachment to Waste Site Reclassification Form 2006-021

International Nuclear Information System (INIS)

Dittmer, L.M.

2006-01-01

The 100-F-33, 146-F Aquatice Biology Fish Ponds waste site was an area with six small rectangular ponds and one large circular pond used to conduct tests on fish using various mixtures of river and reactor effluent water. The current site conditions achieve the remedial action objectives specified in the Remaining Sites ROD. The results of verification and applicable confirmatory sampling show that residual contaminant concentrations do not preclude any future uses and allow for unrestricted use of shallow zone soils. The results also demonstrate that residual contaminant concentrations are protective of groundwater and the Columbia River

Residual stress in deuterium implanted nominal copper coatings

International Nuclear Information System (INIS)

Inal, M. Y.; Alam, M.; Peascoe, R. A.; Watkins, T. R.

2000-01-01

The effects of deuterium (D) implantation on the residual stresses in Cu and CuAl 2 phases present in nominal Cu coatings (containing Al) deposited on Al-alloy (Al-6061) substrates were measured using an x-ray diffraction technique. The coatings were deposited by radio frequency magnetron sputtering of a pure Cu target under identical conditions and Al was incorporated in the coatings during growth by diffusion from the substrate. Deuterium was implanted in the coatings at energies of 40 or 40+120 keV with fluences of 1x10 21 , 2x10 21 , or 3x10 21 D + /m 2 . Pole figures of the Cu phase in the coatings prior to and after implantation indicated no effect of implantation on the fibrous texture. Triaxial stress analysis indicated the surface normal stress component to be negligible in Cu and slightly tensile in CuAl 2 under all conditions. Furthermore, under all conditions, the in-plane residual stresses in both phases were found to be compressive and nearly isotropic. The magnitude of the isotropic compressive stress was always higher in CuAl 2 as compared to Cu. The compressive residual stresses in the Cu phase changed only mildly with increasing coating weight, ion energy, and fluence. However, in the CuAl 2 phase the compressive residual stresses changed markedly with increasing ion energy (initial decrease followed by leveling off) and increasing ion fluence (initial decrease followed by an increase), but remained unaffected by increasing coating weight. (c) 2000 American Institute of Physics

Investigation and analysis of hazardous waste in the Three Gorges Area of Chongqing region

Institute of Scientific and Technical Information of China (English)

LIU Li; LIU Xi-rong; WANG Li-ao; ZHOU Zai-jiang

2004-01-01

This article describes the investigation of hazardous waste (HW) in the Three Gorges Area of Chongqing region, which indicates that by May 2002, the dumped HW therein amounted to 14 600 t and was mainly distributed in five districts and counties with 11 000 t in Fuling, 1 650 t in Fengdu, 950 t in Wanzhou; 630 t in Wushan and 430 t in Yunyang. The total amount was composed of 9 670 t chromic residue, 2 310 t waste oil and residue, 410 t waste (false) fertilizer, 28 t waste chemical medicine, 26 t waste materials and 2 200 t other things including acid residue, waste asbestos, fluorine silicate,pigment, additive, waste acid, alkali, nitric acid, vitriol, lead mud, storage battery, calcium carbide, potassium cyanide, polluted soil, discard dynamite, waste packing barrel of cyanides, etc. In all of the HW, 578 t can be treated by chemical neutralization and stabilization technology such as redox, chemical precipitation, acid and alkali neutralization, etc., and the rest is temporarily untreatble and should be removed and piled at a temporary storage site above the 177 m water level of the dam with an aim to be transported to a future disposal site for innocuous treatment.

Effect of sewage sludge content on gas quality and solid residues produced by cogasification in an updraft gasifier

Energy Technology Data Exchange (ETDEWEB)

Seggiani, Maurizia, E-mail: m.seggiani@diccism.unipi.it [Department of Chemical Engineering, Industrial Chemistry and Material Science, University of Pisa, Largo Lucio Lazzarino 1, 56126 Pisa (Italy); Puccini, Monica, E-mail: m.puccini@diccism.unipi.it [Department of Chemical Engineering, Industrial Chemistry and Material Science, University of Pisa, Largo Lucio Lazzarino 1, 56126 Pisa (Italy); Raggio, Giovanni, E-mail: g.raggio@tiscali.it [Italprogetti Engineering SPA, Lungarno Pacinotti, 59/A, 56020 San Romano (Pisa) (Italy); Vitolo, Sandra, E-mail: s.vitolo@diccism.unipi.it [Department of Chemical Engineering, Industrial Chemistry and Material Science, University of Pisa, Largo Lucio Lazzarino 1, 56126 Pisa (Italy)

2012-10-15

Highlights: Black-Right-Pointing-Pointer Cogasification of sewage sludge with wood pellets in updraft gasifier was analysed. Black-Right-Pointing-Pointer The effects of sewage sludge content on the gasification process were examined. Black-Right-Pointing-Pointer Sewage sludge addition up to 30 wt.% reduces moderately the process performance. Black-Right-Pointing-Pointer At high sewage sludge content slagging and clinker formation occurred. Black-Right-Pointing-Pointer Solid residues produced resulted acceptable at landfills for non-hazardous waste. - Abstract: In the present work, the gasification with air of dehydrated sewage sludge (SS) with 20 wt.% moisture mixed with conventional woody biomass was investigated using a pilot fixed-bed updraft gasifier. Attention was focused on the effect of the SS content on the gasification performance and on the environmental impact of the process. The results showed that it is possible to co-gasify SS with wood pellets (WPs) in updraft fixed-bed gasification installations. However, at high content of sewage sludge the gasification process can become instable because of the very high ash content and low ash fusion temperatures of SS. At an equivalent ratio of 0.25, compared with wood pellets gasification, the addition of sewage sludge led to a reduction of gas yield in favor of an increase of condensate production with consequent cold gas efficiency decrease. Low concentrations of dioxins/furans and PAHs were measured in the gas produced by SS gasification, well below the limiting values for the exhaust gaseous emissions. NH{sub 3}, HCl and HF contents were very low because most of these compounds were retained in the wet scrubber systems. On the other hand, high H{sub 2}S levels were measured due to high sulfur content of SS. Heavy metals supplied with the feedstocks were mostly retained in gasification solid residues. The leachability tests performed according to European regulations showed that metals leachability was

76 FR 55846 - Hazardous Waste Management System: Identification and Listing of Hazardous Waste: Carbon Dioxide...

Science.gov (United States)

2011-09-09

... carbon dioxide (CO 2 ) streams that are hazardous from the definition of hazardous waste, provided these... management under the Resource Conservation and Recovery Act (RCRA) to conditionally exclude carbon dioxide... 2050-AG60 Hazardous Waste Management System: Identification and Listing of Hazardous Waste: Carbon...

HAZARD ANALYSIS SOFTWARE

International Nuclear Information System (INIS)

Sommer, S; Tinh Tran, T.

2008-01-01

Washington Safety Management Solutions, LLC developed web-based software to improve the efficiency and consistency of hazard identification and analysis, control selection and classification, and to standardize analysis reporting at Savannah River Site. In the new nuclear age, information technology provides methods to improve the efficiency of the documented safety analysis development process which includes hazard analysis activities. This software provides a web interface that interacts with a relational database to support analysis, record data, and to ensure reporting consistency. A team of subject matter experts participated in a series of meetings to review the associated processes and procedures for requirements and standard practices. Through these meetings, a set of software requirements were developed and compiled into a requirements traceability matrix from which software could be developed. The software was tested to ensure compliance with the requirements. Training was provided to the hazard analysis leads. Hazard analysis teams using the software have verified its operability. The software has been classified as NQA-1, Level D, as it supports the analysis team but does not perform the analysis. The software can be transported to other sites with alternate risk schemes. The software is being used to support the development of 14 hazard analyses. User responses have been positive with a number of suggestions for improvement which are being incorporated as time permits. The software has enforced a uniform implementation of the site procedures. The software has significantly improved the efficiency and standardization of the hazard analysis process

Determination of Effective Criteria for location Selection of WPC Plants from agricultural residues in Iran by AHP Technique

Directory of Open Access Journals (Sweden)

hasan alizadeh

2017-02-01

Full Text Available This study was aimed at determining the effective criteria for location selection of WPC Plants from agricultural residues in Iran. For this purpose, after review and studies papers and books, Six criteria" products and materials, regulations, technical and human, economic, infrastructure and environmental and also 30 sub-criteria were identified. The priority rates of these criteria and sub-criteria were evaluated by AHP technique. The results indicated that among 30 effective sub-criteria in location selection of the WPC plants from agricultural residues, amount of wastes supply (0.087, continuity of wastes supply, cost of wastes supply, amount of sales and export, granted facilities and less Hazards for the environment and forest had the highest priorities, which were rated as 0.071, 0.067, 0.065, 0.064 and 0.062 respectively.

Integrated approach for coastal hazards and risks in Sri Lanka

Science.gov (United States)

Garcin, M.; Desprats, J. F.; Fontaine, M.; Pedreros, R.; Attanayake, N.; Fernando, S.; Siriwardana, C. H. E. R.; de Silva, U.; Poisson, B.

2008-06-01

The devastating impact of the tsunami of 26 December 2004 on the shores of the Indian Ocean recalled the importance of knowledge and the taking into account of coastal hazards. Sri Lanka was one of the countries most affected by this tsunami (e.g. 30 000 dead, 1 million people homeless and 70% of the fishing fleet destroyed). Following this tsunami, as part of the French post-tsunami aid, a project to establish a Geographical Information System (GIS) on coastal hazards and risks was funded. This project aims to define, at a pilot site, a methodology for multiple coastal hazards assessment that might be useful for the post-tsunami reconstruction and for development planning. This methodology could be applied to the whole coastline of Sri Lanka. The multi-hazard approach deals with very different coastal processes in terms of dynamics as well as in terms of return period. The first elements of this study are presented here. We used a set of tools integrating a GIS, numerical simulations and risk scenario modelling. While this action occurred in response to the crisis caused by the tsunami, it was decided to integrate other coastal hazards into the study. Although less dramatic than the tsunami these remain responsible for loss of life and damage. Furthermore, the establishment of such a system could not ignore the longer-term effects of climate change on coastal hazards in Sri Lanka. This GIS integrates the physical and demographic data available in Sri Lanka that is useful for assessing the coastal hazards and risks. In addition, these data have been used in numerical modelling of the waves generated during periods of monsoon as well as for the December 2004 tsunami. Risk scenarios have also been assessed for test areas and validated by field data acquired during the project. The results obtained from the models can be further integrated into the GIS and contribute to its enrichment and to help in better assessment and mitigation of these risks. The coastal-hazards

Integrated approach for coastal hazards and risks in Sri Lanka

Directory of Open Access Journals (Sweden)

M. Garcin

2008-06-01

Full Text Available The devastating impact of the tsunami of 26 December 2004 on the shores of the Indian Ocean recalled the importance of knowledge and the taking into account of coastal hazards. Sri Lanka was one of the countries most affected by this tsunami (e.g. 30 000 dead, 1 million people homeless and 70% of the fishing fleet destroyed. Following this tsunami, as part of the French post-tsunami aid, a project to establish a Geographical Information System (GIS on coastal hazards and risks was funded. This project aims to define, at a pilot site, a methodology for multiple coastal hazards assessment that might be useful for the post-tsunami reconstruction and for development planning. This methodology could be applied to the whole coastline of Sri Lanka.

The multi-hazard approach deals with very different coastal processes in terms of dynamics as well as in terms of return period. The first elements of this study are presented here. We used a set of tools integrating a GIS, numerical simulations and risk scenario modelling. While this action occurred in response to the crisis caused by the tsunami, it was decided to integrate other coastal hazards into the study. Although less dramatic than the tsunami these remain responsible for loss of life and damage. Furthermore, the establishment of such a system could not ignore the longer-term effects of climate change on coastal hazards in Sri Lanka.

This GIS integrates the physical and demographic data available in Sri Lanka that is useful for assessing the coastal hazards and risks. In addition, these data have been used in numerical modelling of the waves generated during periods of monsoon as well as for the December 2004 tsunami. Risk scenarios have also been assessed for test areas and validated by field data acquired during the project. The results obtained from the models can be further integrated into the GIS and contribute to its enrichment and to help in better assessment and mitigation

Characterization of hazardous waste residuals from Environmental Restoration Program activities at DOE installations: Waste management implications

International Nuclear Information System (INIS)

Lazaro, M.A.; Esposito, M.P.

1995-01-01

Investigators at Argonne National Laboratory (ANL), with support from associates at the Pacific Northwest Laboratory (PNL), have assembled an inventory of the types and volumes of radioactive, toxic or hazardous, and mixed waste likely to be generated over the next 30 years as the US Department of Energy (DOE) implements its nationwide Environmental Restoration (ER) Program. The inventory and related analyses are being considered for integration into DOE's Programmatic Environmental Impact Statement (PEIS) covering the potential environmental impacts and risks associated with alternative management practices and programs for wastes generated from routine operations. If this happens, the ER-generated waste could be managed under a set of alternatives considered under the PEIS and selected at the end of the current National Environmental Policy Act process

Standard test method for determining residual stresses by the hole-drilling strain-gage method

CERN Document Server

American Society for Testing and Materials. Philadelphia

2008-01-01

1.1 Residual Stress Determination: 1.1.1 This test method specifies a hole-drilling procedure for determining residual stress profiles near the surface of an isotropic linearly elastic material. The test method is applicable to residual stress profile determinations where in-plane stress gradients are small. The stresses may remain approximately constant with depth (“uniform” stresses) or they may vary significantly with depth (“non-uniform” stresses). The measured workpiece may be “thin” with thickness much less than the diameter of the drilled hole or “thick” with thickness much greater than the diameter of the drilled hole. Only uniform stress measurements are specified for thin workpieces, while both uniform and non-uniform stress measurements are specified for thick workpieces. 1.2 Stress Measurement Range: 1.2.1 The hole-drilling method can identify in-plane residual stresses near the measured surface of the workpiece material. The method gives localized measurements that indicate the...

Hazardous Chemicals

Centers for Disease Control (CDC) Podcasts

Chemicals are a part of our daily lives, providing many products and modern conveniences. With more than three decades of experience, The Centers for Disease Control and Prevention (CDC) has been in the forefront of efforts to protect and assess people's exposure to environmental and hazardous chemicals. This report provides information about hazardous chemicals and useful tips on how to protect you and your family from harmful exposure.

Technical Guidance for Hazardous Analysis, Emergency Planning for Extremely Hazardous Substances

Science.gov (United States)

This current guide supplements NRT-1 by providing technical assistance to LEPCs to assess the lethal hazards related to potential airborne releases of extremely hazardous substances (EHSs) as designated under Section 302 of Title Ill of SARA.

Is residual memory variance a valid method for quantifying cognitive reserve? A longitudinal application.

Science.gov (United States)

Zahodne, Laura B; Manly, Jennifer J; Brickman, Adam M; Narkhede, Atul; Griffith, Erica Y; Guzman, Vanessa A; Schupf, Nicole; Stern, Yaakov

2015-10-01

Cognitive reserve describes the mismatch between brain integrity and cognitive performance. Older adults with high cognitive reserve are more resilient to age-related brain pathology. Traditionally, cognitive reserve is indexed indirectly via static proxy variables (e.g., years of education). More recently, cross-sectional studies have suggested that reserve can be expressed as residual variance in episodic memory performance that remains after accounting for demographic factors and brain pathology (whole brain, hippocampal, and white matter hyperintensity volumes). The present study extends these methods to a longitudinal framework in a community-based cohort of 244 older adults who underwent two comprehensive neuropsychological and structural magnetic resonance imaging sessions over 4.6 years. On average, residual memory variance decreased over time, consistent with the idea that cognitive reserve is depleted over time. Individual differences in change in residual memory variance predicted incident dementia, independent of baseline residual memory variance. Multiple-group latent difference score models revealed tighter coupling between brain and language changes among individuals with decreasing residual memory variance. These results suggest that changes in residual memory variance may capture a dynamic aspect of cognitive reserve and could be a useful way to summarize individual cognitive responses to brain changes. Change in residual memory variance among initially non-demented older adults was a better predictor of incident dementia than residual memory variance measured at one time-point. Copyright © 2015. Published by Elsevier Ltd.

Optimization of ethanol production from garcinia cambogia residues and the effects of its medicinal component on production yield

International Nuclear Information System (INIS)

Ma, H.; Zhang, F.

2017-01-01

Garcinia cambogia, a Chinese herbal medicine, was popular due to its effect for weight loss. The main medical component inside was determined to be hydroxycitric acid (HCA). To realize the resource technology of garcinia cambogia residue, Optimum ethanol production from residues was investigated, and the effects of remaining HCA on the ethanol yield were investigated. A Plackett-Burman experimental design was used to screen the significance of several influencing factors, and cellulase, yeast extract, and KH2PO4 were observed to exert important effects. The optimum ethanol fermentation conditions were determined through an orthogonal design to include a cellulase concentration of 100 U/g, a yeast extract concentration of 15 g/L, and a KH2PO4 concentration of 1.0 g/L. The ethanol concentration obtained under optimal conditions was 4.0 g/L. The remained HCA in the residues showed minimal influences on ethanol fermentation and could even increase ethanol yield at low concentrations. (author)

Estimation of residual life of boiler tubes using steamside oxide scale thickness

International Nuclear Information System (INIS)

Vikrant, K.S.N.; Ramareddy, G.V.; Pavan, A.H.V.; Singh, Kulvir

2013-01-01

In thermal power plants, remaining-life-estimation of boiler tubes is required at regular intervals for a safer and a better functionality of boilers. In this paper, a new method is proposed for the residual life estimation of service exposed boiler tubes using Non-Destructive Ultrasonic Oxide scale thickness measurements, average metal temperature and creep master curve. While steady state conduction heat transfer equations are solved to calculate the average metal temperature, creep master curve is generated from short term stress rupture data of rupture life less than 5000 h on a virgin material. In the present study, the residual life of T22 (2.25Cr-1Mo) service exposed Platen Superheater tube is estimated using two master creep curves, i.e. Larson-Miller Parametric (LMP) method of standard ASME T22 creep data and Wilshire approach of short term stress rupture data of T22. As the residual life is calculated from fundamental conduction heat transfer theory and creep rupture data, the proposed method can be applied for different grades of boiler materials. -- Highlights: ► Residual life is calculated from non-destructive oxide scale thickness, creep master curve and average metal temperature. ► A new method is proposed for calculating residual life using above parameters and from conduction heat transfer principles. ► The method can be applied to different boiler grades for estimating residual life and hence the method is generic

Residual gas analysis

International Nuclear Information System (INIS)

Berecz, I.

1982-01-01

Determination of the residual gas composition in vacuum systems by a special mass spectrometric method was presented. The quadrupole mass spectrometer (QMS) and its application in thin film technology was discussed. Results, partial pressure versus time curves as well as the line spectra of the residual gases in case of the vaporization of a Ti-Pd-Au alloy were demonstrated together with the possible construction schemes of QMS residual gas analysers. (Sz.J.)

Identification and quantification of pesticide residues in water samples of Dhamrai Upazila, Bangladesh

Science.gov (United States)

Hasanuzzaman, M.; Rahman, M. A.; Salam, M. A.

2017-10-01

Being agricultural country, different types of pesticides are widely used in Bangladesh to prevent the crop losses due to pest attack which are ultimately drain to the water bodies. The present study was conducted to identify and quantify the organochlorine (DDT, DDE and DDD), organophosphorus (malathion, diazinon and chloropyrifos) and carbamate (carbaryl) residues in water samples of different sources from Dhamrai upazila of Bangladesh using high performance liquid chromatography (HPLC) equipped with ultra violate (UV) detector. Thirty water samples from fish pond, cultivated land and tube-well were collected in winter season to analyze the pesticide residues. Among the organophosphorus pesticides, malathion was present in seven water samples ranging from 42.58 to 922.8 μg/L, whereas diazinon was detected in water sample-8 (WS-8) and the concentration was 31.5 μg/L. None of the tested water samples was found to be contaminated with chlorpyrifos, carbaryl or DDT and its metabolites (DDE and DDD). Except for a tube-well water sample, concentrations of the detected residues are above the acceptable limit for human body as assigned by different organizations. To avoid the possible health hazards, the indiscriminate application of pesticides should be restricted and various substitute products like bio-pesticide should be introduced in a broad scale as soon as possible.

The Coastal Hazard Wheel system for coastal multi-hazard assessment & management in a changing climate

DEFF Research Database (Denmark)

Appelquist, Lars Rosendahl; Halsnæs, Kirsten

2015-01-01

This paper presents the complete Coastal Hazard Wheel (CHW) system, developed for multi-hazard-assessment and multi-hazard-management of coastal areas worldwide under a changing climate. The system is designed as a low-tech tool that can be used in areas with limited data availability...... screening and management. The system is developed to assess the main coastal hazards in a single process and covers the hazards of ecosystem disruption, gradual inundation, salt water intrusion, erosion and flooding. The system was initially presented in 2012 and based on a range of test......-applications and feedback from coastal experts, the system has been further refined and developed into a complete hazard management tool. This paper therefore covers the coastal classification system used by the CHW, a standardized assessment procedure for implementation of multi-hazard-assessments, technical guidance...

Disposal of hazardous wastes

International Nuclear Information System (INIS)

Barnhart, B.J.

1978-01-01

The Fifth Life Sciences Symposium entitled Hazardous Solid Wastes and Their Disposal on October 12 through 14, 1977 was summarized. The topic was the passage of the National Resources Conservation and Recovery Act of 1976 will force some type of action on all hazardous solid wastes. Some major points covered were: the formulation of a definition of a hazardous solid waste, assessment of long-term risk, list of specific materials or general criteria to specify the wastes of concern, Bioethics, sources of hazardous waste, industrial and agricultural wastes, coal wastes, radioactive wastes, and disposal of wastes

Assessing the Availability of Wood Residues and Residue Markets in Virginia

OpenAIRE

Alderman, Delton R. Jr.

1998-01-01

A statewide mail survey of primary and secondary wood product manufacturers was undertaken to quantify the production and consumption of wood residues in Virginia. Two hundred and sixty-six wood product manufacturers responded to the study and they provided information on the production, consumption, markets, income or disposal costs, and disposal methods of wood residues. Hardwood and pine sawmills produce approximately 66 percent of Virginia's wood residues. Virginia's wood product man...

Improved Performance and Safety for High Energy Batteries Through Use of Hazard Anticipation and Capacity Prediction

Science.gov (United States)

Atwater, Terrill

1993-01-01

Prediction of the capacity remaining in used high rate, high energy batteries is important information to the user. Knowledge of the capacity remaining in used batteries results in better utilization. This translates into improved readiness and cost savings due to complete, efficient use. High rate batteries, due to their chemical nature, are highly sensitive to misuse (i.e., over discharge or very high rate discharge). Battery failure due to misuse or manufacturing defects could be disastrous. Since high rate, high energy batteries are expensive and energetic, a reliable method of predicting both failures and remaining energy has been actively sought. Due to concerns over safety, the behavior of lithium/sulphur dioxide cells at different temperatures and current drains was examined. The main thrust of this effort was to determine failure conditions for incorporation in hazard anticipation circuitry. In addition, capacity prediction formulas have been developed from test data. A process that performs continuous, real-time hazard anticipation and capacity prediction was developed. The introduction of this process into microchip technology will enable the production of reliable, safe, and efficient high energy batteries.

Evaluation of residual activity of solid waste generated in nuclear medicine services of Porto Alegre - Brazil

International Nuclear Information System (INIS)

Xavier, Ana M.; Alabarse, Frederico Gil; Magalhaes, Maisa Haiidamus; Guerrero, Jesus Salvador Perez

2008-01-01

An experimental programme to estimate, with a better degree of accuracy, the activity that remains adsorbed in flasks and syringes used in Nuclear Medicine Services for the administration of radionuclides to patients submitted to diagnostic or therapy was conducted under the coordination of the Radioactive Waste Division of the Brazilian Nuclear Energy Commission. The adopted recommendation in Brazil to allow an expedite solid waste management in nuclear medicine facilities, up to the present, is to consider that 2% of the initial activity remains adsorbed in the solid waste, which easily allows the calculation of the storage time to achieve regulatory clearance levels by decay. This research evaluates 17 different kinds of radio pharmaceuticals and three radioisotopes: 99m Tc, 67 Ga and 201 Tl. Results obtained by means of a weighting method to estimate the residual mass in flasks show that the ratio of the mass of the liquid that remains in the solid waste to the mass of the empty flask is constant. This suggests that the residual activity depends on the initial activity concentration of radiopharmaceutical contained in each flask, as assumed by the regulatory body. Additionally, results obtained by determining the remaining activity in flasks, shortly after the injection of its radionuclides contents in patients, indicate that an average value for the residual activity of the order of 10% of the initial activity contained in the flasks or syringes can be adopted instead of the previously assumed 2%. It is suggested that the more conservative average value obtained in the present work for the activity that remains in flasks and syringes, that is, 10% of the initial activity, could be adopted to determine the decay storage time before the release of solid waste in the urban conventional land fill disposal system. (author)

Assessment for the management of NORM wastes in conventional hazardous and nonhazardous waste landfills

Energy Technology Data Exchange (ETDEWEB)

Mora, Juan C., E-mail: jc.mora@ciemat.es [Unit for Radiation Protection of the Public and the Environment (PRPYMA), CIEMAT, Avda. Complutense, 40, 28040 Madrid (Spain); Energy Engineering Department, Power Engineering, Nuclear Area, ETSII, UNED (Spain); Baeza, Antonio [LARUEX, Dpt. Applied Physics, Faculty of Veterinary Science, University of Extremadura, Avda. Universidad, s/n, 10071 Cáceres (Spain); Robles, Beatriz [Unit for Radiation Protection of the Public and the Environment (PRPYMA), CIEMAT, Avda. Complutense, 40, 28040 Madrid (Spain); Sanz, Javier [Energy Engineering Department, Power Engineering, Nuclear Area, ETSII, UNED (Spain)

2016-06-05

Highlights: • Before 2010 NORM waste is managed as non-radioactive, disposed in landfills. • After 2010 radiological impact of the management of NORM wastes must be assessed. • Quantities that can be disposed in hazardous or non-hazardous landfills are given. • Uncertainty analysis is included to provide consistency to the calculations. - Abstract: Naturally Occurring Radioactive Materials (NORM) wastes are generated in huge quantities in several industries and their management has been carried out under considerations of industrial non-radioactive wastes, before the concern on the radioactivity content was included in the legislation. Therefore these wastes were conditioned using conventional methods and the waste disposals were designed to isolate toxic elements from the environment for long periods of time. Spanish regulation for these conventional toxic waste disposals includes conditions that assure adequate isolation to minimize the impact of the wastes to the environment in present and future conditions. After 1996 the radiological impact of the management of NORM wastes is considered and all the aspects related with natural radiations and the radiological control regarding the management of residues from NORM industries were developed in the new regulation. One option to be assessed is the disposal of NORM wastes in hazardous and non-hazardous waste disposals, as was done before this new regulation. This work analyses the management of NORM wastes in these landfills to derive the masses that can be disposed without considerable radiological impact. Generic dose assessments were carried out under highly conservative hypothesis and a discussion on the uncertainty and variability sources was included to provide consistency to the calculations.

Assessment for the management of NORM wastes in conventional hazardous and nonhazardous waste landfills

International Nuclear Information System (INIS)

Mora, Juan C.; Baeza, Antonio; Robles, Beatriz; Sanz, Javier

2016-01-01

Highlights: • Before 2010 NORM waste is managed as non-radioactive, disposed in landfills. • After 2010 radiological impact of the management of NORM wastes must be assessed. • Quantities that can be disposed in hazardous or non-hazardous landfills are given. • Uncertainty analysis is included to provide consistency to the calculations. - Abstract: Naturally Occurring Radioactive Materials (NORM) wastes are generated in huge quantities in several industries and their management has been carried out under considerations of industrial non-radioactive wastes, before the concern on the radioactivity content was included in the legislation. Therefore these wastes were conditioned using conventional methods and the waste disposals were designed to isolate toxic elements from the environment for long periods of time. Spanish regulation for these conventional toxic waste disposals includes conditions that assure adequate isolation to minimize the impact of the wastes to the environment in present and future conditions. After 1996 the radiological impact of the management of NORM wastes is considered and all the aspects related with natural radiations and the radiological control regarding the management of residues from NORM industries were developed in the new regulation. One option to be assessed is the disposal of NORM wastes in hazardous and non-hazardous waste disposals, as was done before this new regulation. This work analyses the management of NORM wastes in these landfills to derive the masses that can be disposed without considerable radiological impact. Generic dose assessments were carried out under highly conservative hypothesis and a discussion on the uncertainty and variability sources was included to provide consistency to the calculations.

Offsite transportation hazards assessment

International Nuclear Information System (INIS)

Burnside, M.E.

1997-01-01

This report documents the emergency preparedness Hazards Assessment for the offsite transportation of hazardous material from the Hanford Site. The assessment is required by the US Department of Energy (DOE) Order 151.1. Offsite transportation accidents are categorized using the DOE system to assist communication within the DOE and assure that appropriate assistance is provided to the people in charge at the scene. The assistance will initially include information about the load and the potential hazards. Local authorities will use the information to protect the public following a transportation accident. This Hazards Assessment will focus on the material being transported from the Hanford Site. Shipments coming to Hanford are the responsibility of the shipper and the carrier and, therefore, are not included in this Hazards Assessment, unless the DOE elects to be the shipper of record

Assessment of the effect of washing and boiling on the levels of pesticide residues in vegetables cultivated in Akuapem North Municipality

International Nuclear Information System (INIS)

Opare-Boafo, Maame Serwa

2016-07-01

cutting into pieces was found to cause percentage reduction of chloropyrifos residues between 9% and 14%. But with 3% of NaCl in water the percentage reduction was between 31% and 42%. Vinegar was found to have significant effect on the reduction of chloropyrifos residue in different vegetables. The percent reduction of chloropyrifos residue after washing with 3% of vinegar in water was between 57% and 69%. Boiling/cooking for 15 minutes at a temperature of 75 °C was observed to be more effective in reducing the pesticide among the various washing treatments. The cooking process reduced the residues between 84 and 93%. Estimated dose values recorded indicated that consumption of vegetables from the Akwapim North Municipality does not pose a direct hazard to human health since their values were lower than toxic thresholds (reference dose) because all the hazard indices were less than 1. Even though the various treatments reduce the residues in vegetables, none of the treatment methods reduced the residue level to zero. Hence, there is no zero risk because pesticides were detected in all the vegetable samples. (au)

Radiological hazards of alpha-contaminated waste

International Nuclear Information System (INIS)

Rodgers, J.C.

1982-01-01

The radiological hazards of alpha-contaminated wastes are discussed in this overview in terms of two components of hazard: radiobiological hazard, and radioecological hazard. Radiobiological hazard refers to human uptake of alpha-emitters by inhalation and ingestion, and the resultant dose to critical organs of the body. Radioecological hazard refers to the processes of release from buried wastes, transport in the environment, and translocation to man through the food chain. Besides detailing the sources and magnitude of hazards, this brief review identifies the uncertainties in their estimation, and implications for the regulatory process

Hazards from aircraft

International Nuclear Information System (INIS)

Grund, J.E.; Hornyik, K.

1975-01-01

The siting of nuclear power plants has created innumerable environmental concerns. Among the effects of the ''man-made environment'' one of increasing importance in recent nuclear plant siting hazards analysis has been the concern about aircraft hazards to the nuclear plant. These hazards are of concern because of the possibility that an aircraft may have a malfunction and crash either near the plant or directly into it. Such a crash could be postulated to result, because of missile and/or fire effects, in radioactive releases which would endanger the public health and safety. The majority of studies related to hazards from air traffic have been concerned with the determination of the probability associated with an aircraft striking vulnerable portions of a given plant. Other studies have focused on the structural response to such a strike. This work focuses on the problem of strike probability. 13 references

Residual limb skin temperature and thermal comfort in people with amputation during activity in a cold environment.

Science.gov (United States)

Segal, Ava D; Klute, Glenn K

2016-01-01

Thermal comfort remains a common problem for people with lower-limb amputation. Both donning a prosthesis and engaging in activity at room temperature can increase residual limb skin temperature; however, the effects of activity on skin temperature and comfort in more extreme environments remain unknown. We examined residual limb skin temperatures and perceived thermal comfort (PTC; 11-point Likert scale) of participants with unilateral transtibial amputation (n = 8) who were snowshoeing in a cold environment. Residual limb skin temperature increased by 3.9°C [3.0°C to 4.7°C] (mean difference [95% confidence interval (CI)], p < 0.001) after two 30 min exercise sessions separated by a 5 min rest session. Minimal cooling (-0.2°C [-1.1°C to 0.6°C]) occurred during the rest period. Similar changes in PTC were found for the residual limb, intact limb, and whole body, with a mean scale increase of 1.6 [1.1 to 2.1] and 1.3 [0.8 to 1.8] for the first and second exercise sessions, respectively (p < 0.001). Activity in a cold environment caused similar increases in residual limb skin temperature as those found in studies conducted at room temperature. Participants with amputation perceived warming as their skin temperature increased during exercise followed by the perception of cooling during rest, despite minimal associated decreases in skin temperature.

A survey of the Maralinga atomic weapons testing range for residual plutonium contamination

International Nuclear Information System (INIS)

Ellis, W.R.

1979-06-01

Residual plutonium levels in soil, flora, fauna and the air of the Maralinga (South Australia) Atomic Weapons Testing Range are presented and discussed. It is shown that only on rare occasions (and possibly never) would the plutonium concentration in air from wind resuspended dust exceed the maximum allowable concentration for continuous exposure of the general public. In the case of artificially resuspended dust, this maximum concentration could be exceeded for short periods, but the accompanying dust level would be such that working conditions would be uncomfortable, if not intolerable. Potential hazards from other possible exposure routes are so low that they are of no consequence

Exploring the effects of driving experience on hazard awareness and risk perception via real-time hazard identification, hazard classification, and rating tasks.

Science.gov (United States)

Borowsky, Avinoam; Oron-Gilad, Tal

2013-10-01

This study investigated the effects of driving experience on hazard awareness and risk perception skills. These topics have previously been investigated separately, yet a novel approach is suggested where hazard awareness and risk perception are examined concurrently. Young, newly qualified drivers, experienced drivers, and a group of commercial drivers, namely, taxi drivers performed three consecutive tasks: (1) observed 10 short movies of real-world driving situations and were asked to press a button each time they identified a hazardous situation; (2) observed one of three possible sub-sets of 8 movies (out of the 10 they have seen earlier) for the second time, and were asked to categorize them into an arbitrary number of clusters according to the similarity in their hazardous situation; and (3) observed the same sub-set for a third time and following each movie were asked to rate its level of hazardousness. The first task is considered a real-time identification task while the other two are performed using hindsight. During it participants' eye movements were recorded. Results showed that taxi drivers were more sensitive to hidden hazards than the other driver groups and that young-novices were the least sensitive. Young-novice drivers also relied heavily on materialized hazards in their categorization structure. In addition, it emerged that risk perception was derived from two major components: the likelihood of a crash and the severity of its outcome. Yet, the outcome was rarely considered under time pressure (i.e., in real-time hazard identification tasks). Using hindsight, when drivers were provided with the opportunity to rate the movies' hazardousness more freely (rating task) they considered both components. Otherwise, in the categorization task, they usually chose the severity of the crash outcome as their dominant criterion. Theoretical and practical implications are discussed. Copyright © 2013 Elsevier Ltd. All rights reserved.

Probabilistic Tsunami Hazard Analysis

Science.gov (United States)

Thio, H. K.; Ichinose, G. A.; Somerville, P. G.; Polet, J.

2006-12-01

The recent tsunami disaster caused by the 2004 Sumatra-Andaman earthquake has focused our attention to the hazard posed by large earthquakes that occur under water, in particular subduction zone earthquakes, and the tsunamis that they generate. Even though these kinds of events are rare, the very large loss of life and material destruction caused by this earthquake warrant a significant effort towards the mitigation of the tsunami hazard. For ground motion hazard, Probabilistic Seismic Hazard Analysis (PSHA) has become a standard practice in the evaluation and mitigation of seismic hazard to populations in particular with respect to structures, infrastructure and lifelines. Its ability to condense the complexities and variability of seismic activity into a manageable set of parameters greatly facilitates the design of effective seismic resistant buildings but also the planning of infrastructure projects. Probabilistic Tsunami Hazard Analysis (PTHA) achieves the same goal for hazards posed by tsunami. There are great advantages of implementing such a method to evaluate the total risk (seismic and tsunami) to coastal communities. The method that we have developed is based on the traditional PSHA and therefore completely consistent with standard seismic practice. Because of the strong dependence of tsunami wave heights on bathymetry, we use a full waveform tsunami waveform computation in lieu of attenuation relations that are common in PSHA. By pre-computing and storing the tsunami waveforms at points along the coast generated for sets of subfaults that comprise larger earthquake faults, we can efficiently synthesize tsunami waveforms for any slip distribution on those faults by summing the individual subfault tsunami waveforms (weighted by their slip). This efficiency make it feasible to use Green's function summation in lieu of attenuation relations to provide very accurate estimates of tsunami height for probabilistic calculations, where one typically computes

Mutational properties of amino acid residues: implications for evolvability of phosphorylatable residues

DEFF Research Database (Denmark)

Creixell, Pau; Schoof, Erwin M.; Tan, Chris Soon Heng

2012-01-01

in terms of their mutational activity. Moreover, we highlight the importance of the genetic code and physico-chemical properties of the amino acid residues as likely causes of these inequalities and uncover serine as a mutational hot spot. Finally, we explore the consequences that these different......; it is typically assumed that all amino acid residues are equally likely to mutate or to result from a mutation. Here, by reconstructing ancestral sequences and computing mutational probabilities for all the amino acid residues, we refute this assumption and show extensive inequalities between different residues...... mutational properties have on phosphorylation site evolution, showing that a higher degree of evolvability exists for phosphorylated threonine and, to a lesser extent, serine in comparison with tyrosine residues. As exemplified by the suppression of serine's mutational activity in phosphorylation sites, our...

Flood hazards for nuclear power plants

International Nuclear Information System (INIS)

Yen, B.C.

1988-01-01

Flooding hazards for nuclear power plants may be caused by various external geophysical events. In this paper the hydrologic hazards from flash floods, river floods and heavy rain at the plant site are considered. Depending on the mode of analysis, two types of hazard evaluation are identified: 1) design hazard which is the probability of flooding over an expected service period, and 2) operational hazard which deals with real-time forecasting of the probability of flooding of an incoming event. Hazard evaluation techniques using flood frequency analysis can only be used for type 1) design hazard. Evaluation techniques using rainfall-runoff simulation or multi-station correlation can be used for both types of hazard prediction. (orig.)

Investigation of patient, tumour and treatment variables affecting residual motion for respiratory-gated radiotherapy

International Nuclear Information System (INIS)

George, R; Ramakrishnan, V; Siebers, J V; Chung, T D; Keall, P J

2006-01-01

Respiratory gating can reduce the apparent respiratory motion during imaging and treatment; however, residual motion within the gating window remains. Respiratory training can improve respiratory reproducibility and, therefore, the efficacy of respiratory-gated radiotherapy. This study was conducted to determine whether residual motion during respiratory gating is affected by patient, tumour or treatment characteristics. The specific aims of this study were to: (1) identify significant characteristics affecting residual motion, (2) investigate time trends of residual motion over a period of days (inter-session) and (3) investigate time trends of residual motion within the same day (intra-session). Twenty-four lung cancer patients were enrolled in an Institutional Review Board (IRB)-approved protocol. For approximately five sessions, 331 four-minute, respiratory motion traces were acquired with free breathing, audio instructions and audio-visual biofeedback for each patient. The residual motion was quantified by the standard deviation of the displacement within the gating window. The generalized linear model was used to obtain coefficients for each variable within the model and to evaluate the clinical and statistical significance. The statistical significance was determined by a p-value <0.05, while effect sizes of ≥0.1 cm (one standard deviation) were considered clinically significant. This data analysis was applied to patient, tumour and treatment variables. Inter- and intra-session variations were also investigated. The only variable that was significant for both inhale- and exhale-based gating was disease type. In addition, visual-training displacement, breathing type and Karnofsky performance status (KPS) values were significant for inhale-based gating, and dose-per-fraction was significant for exhale-based gating. Temporal respiratory variations within and between sessions were observed for individual patients. However inter- and intra-session analyses did

Investigation of patient, tumour and treatment variables affecting residual motion for respiratory-gated radiotherapy

Energy Technology Data Exchange (ETDEWEB)

George, R [Department of Radiation Oncology, Virginia Commonwealth University, Richmond, VA (United States); Ramakrishnan, V [Department of Biostatistics, Virginia Commonwealth University, Richmond, VA (United States); Siebers, J V [Department of Radiation Oncology, Virginia Commonwealth University, Richmond, VA (United States); Chung, T D [Department of Radiation Oncology, Virginia Commonwealth University, Richmond, VA (United States); Keall, P J [Department of Radiation Oncology, Virginia Commonwealth University, Richmond, VA (United States)

2006-10-21

Respiratory gating can reduce the apparent respiratory motion during imaging and treatment; however, residual motion within the gating window remains. Respiratory training can improve respiratory reproducibility and, therefore, the efficacy of respiratory-gated radiotherapy. This study was conducted to determine whether residual motion during respiratory gating is affected by patient, tumour or treatment characteristics. The specific aims of this study were to: (1) identify significant characteristics affecting residual motion, (2) investigate time trends of residual motion over a period of days (inter-session) and (3) investigate time trends of residual motion within the same day (intra-session). Twenty-four lung cancer patients were enrolled in an Institutional Review Board (IRB)-approved protocol. For approximately five sessions, 331 four-minute, respiratory motion traces were acquired with free breathing, audio instructions and audio-visual biofeedback for each patient. The residual motion was quantified by the standard deviation of the displacement within the gating window. The generalized linear model was used to obtain coefficients for each variable within the model and to evaluate the clinical and statistical significance. The statistical significance was determined by a p-value <0.05, while effect sizes of {>=}0.1 cm (one standard deviation) were considered clinically significant. This data analysis was applied to patient, tumour and treatment variables. Inter- and intra-session variations were also investigated. The only variable that was significant for both inhale- and exhale-based gating was disease type. In addition, visual-training displacement, breathing type and Karnofsky performance status (KPS) values were significant for inhale-based gating, and dose-per-fraction was significant for exhale-based gating. Temporal respiratory variations within and between sessions were observed for individual patients. However inter- and intra-session analyses did

Biological treatment of concentrated hazardous, toxic, and radionuclide mixed wastes without dilution

International Nuclear Information System (INIS)

Stringfellow, William T.; Komada, Tatsuyuki; Chang, Li-Yang

2004-01-01

Approximately 10 percent of all radioactive wastes produced in the U. S. are mixed with hazardous or toxic chemicals and therefore can not be placed in secure land disposal facilities. Mixed wastes containing hazardous organic chemicals are often incinerated, but volatile radioactive elements are released directly into the biosphere. Some mixed wastes do not currently have any identified disposal option and are stored locally awaiting new developments. Biological treatment has been proposed as a potentially safer alternative to incineration for the treatment of hazardous organic mixed wastes, since biological treatment would not release volatile radioisotopes and the residual low-level radioactive waste would no longer be restricted from land disposal. Prior studies have shown that toxicity associated with acetonitrile is a significant limiting factor for the application of biotreatment to mixed wastes and excessive dilution was required to avoid inhibition of biological treatment. In this study, we demonstrate that a novel reactor configuration, where the concentrated toxic waste is drip-fed into a complete-mix bioreactor containing a pre-concentrated active microbial population, can be used to treat a surrogate acetonitrile mixed waste stream without excessive dilution. Using a drip-feed bioreactor, we were able to treat a 90,000 mg/L acetonitrile solution to less than 0.1 mg/L final concentration using a dilution factor of only 3.4. It was determined that the acetonitrile degradation reaction was inhibited at a pH above 7.2 and that the reactor could be modeled using conventional kinetic and mass balance approaches. Using a drip-feed reactor configuration addresses a major limiting factor (toxic inhibition) for the biological treatment of toxic, hazardous, or radioactive mixed wastes and suggests that drip-feed bioreactors could be used to treat other concentrated toxic waste streams, such as chemical warfare materiel

Metals accumulations during thermal processing of sewage sludge - characterization of bottom ash and air pollution control (APC) residues

Science.gov (United States)

Kasina, Monika; Kowalski, Piotr R.; Michalik, Marek

2016-04-01

Due to increasing mass of sewage sludge, problems in its management have appeared. Over years sewage sludge was landfilled, however due to EU directives concerning environmental issues this option is no longer possible. This type of material is considered hazardous due to highly concentrated metals and harmful elements, toxic organic substances and biological components (e.g. parasites, microbes). Currently in Europe, incineration is considered to be the most reasonable method for sewage sludge treatment. As a result of sludge incineration significant amount of energy is recovered due to high calorific value of sewage sludge but bottom ash and APC residues are being produced. In this study we show the preliminary results of chemical and mineral analyses of both bottom ash and APC residues produced in fluidized bed boiler in sewage sludge incineration plant in Poland, with a special emphasis on metals which, as a part of incombustible fraction can accumulate in the residual materials after thermal processing. The bottom ash was a SiO2-P2O5-Fe2O3-CaO-Al2O3 dominated material. Main mineral phases identified in X-ray diffraction patterns were: quartz, feldspar, hematite, and phosphates (apatite and scholzite). The bottom ash was characterized by high content of Zn - 4472 mg kg-1, Cu - 665.5 mg kg-1, Pb - 138 mg kg-1, Ni - 119.5 mg kg-1, and interestingly high content of Au - 0.858 mg kg-1 The APC residues composition was dominated by soluble phases which represent more than 90% of the material. The XRD patterns indicated thenardite, halite, anhydrite, calcite and apatite as main mineral phases. The removal of soluble phases by dissolution in deionised water caused a significant mass reduction (ca. 3% of material remained on the filters). Calcite, apatite and quartz were main identified phases. The content of metals in insoluble material is relatively high: Zn - 6326 mg kg-1, Pb - 514.3 mg kg-1, Cu - 476.6 mg kg-1, Ni - 43.3 mg kg-1. The content of Cd, As, Se and Hg was

Remaining Sites Verification Package for the 100-B-1 Surface Chemical and Solid Waste Dumping Area,. Attachment to Waste Site Reclassification Form 2006-003

International Nuclear Information System (INIS)

Carlson, R.A.

2006-01-01

The 100-B-1 waste site was a dumping site that was divided into two areas. One area was used as a laydown area for construction materials, and the other area was used as a chemical dumping area. The 100-B-1 Surface Chemical and Solid Waste Dumping Area site meets the remedial action objectives specified in the Remaining Sites ROD. The results demonstrate that residual contaminant concentrations support future unrestricted land uses that can be represented by a rural-residential scenario. The results also demonstrate that residual contaminant concentrations are protective of groundwater and the Columbia River

Preclosure seismic hazards and their impact on site suitability of Yucca Mountain, Nevada

International Nuclear Information System (INIS)

Gibson, J.D.

1992-01-01

This paper presents an overview of the preclosure seismic hazards and the influence of these hazards on determining the suitability of Yucca Mountain as a national high-level nuclear-waste repository. Geologic data, engineering analyses, and regulatory guidelines must be examined collectively to assess this suitability. An environmental assessment for Yucca Mountain, written in 1986, compiled and evaluated the existing tectonic data and presented arguments to satisfy, in part, the regulatory requirements that must be met if the Yucca Mountain site is to become a national waste repository. Analyses have been performed in the past five years that better quantify the local seismic hazards and the possibility that these hazards could lead to release of radionuclides to the environment. The results from these analyses increase the confidence in the ability of Yucca Mountain and the facilities that may be built there to function satisfactorily in their role as a waste repository. Uncertainties remain, however, primarily in the input parameters and boundary conditions for the models that were used to complete the analyses. These models must be validated and uncertainties reduced before Yucca Mountain can qualify as a viable high-level nuclear waste repository

Hazardous substances in the aquatic environment of Estonia.

Science.gov (United States)

Roots, Ott; Roose, Antti

2013-09-01

The Water Framework Directive (WFD) aims to regulate the management of European surface water bodies. Directive 2008/105/EC, which establishes the environmental quality standards of priority substances and certain other pollutants, the content of which in the surface water should be monitored, has been transposed by the Estonian Ministry of Environment 9 September 2010 Regulation No. 49. Sampled hazardous substances were selected primarily based on their toxicity, as well as their lifetime in environment and ability to accumulate in living organisms (bioaccumulation). The contents of hazardous substances and their groups determined from Estonian surface waters remained below the limits of quantifications of used analysis methods in most cases. However, the content of some heavy metals, mono- and dibasic phenols in the surface water/waste water and sewage sludge/bottom sediments can still reach the delicate levels in the Estonian oil shale region in particular. Among new substances analysed in Estonia historically first time in 2010, amounts of organotin compounds in sediments and some alkylphenols, their ethoxylates and phthalates were found in various sample matrices. Copyright © 2013 Elsevier Ltd. All rights reserved.

Evaluation of residue-residue contact prediction in CASP10

KAUST Repository

Monastyrskyy, Bohdan

2013-08-31

We present the results of the assessment of the intramolecular residue-residue contact predictions from 26 prediction groups participating in the 10th round of the CASP experiment. The most recently developed direct coupling analysis methods did not take part in the experiment likely because they require a very deep sequence alignment not available for any of the 114 CASP10 targets. The performance of contact prediction methods was evaluated with the measures used in previous CASPs (i.e., prediction accuracy and the difference between the distribution of the predicted contacts and that of all pairs of residues in the target protein), as well as new measures, such as the Matthews correlation coefficient, the area under the precision-recall curve and the ranks of the first correctly and incorrectly predicted contact. We also evaluated the ability to detect interdomain contacts and tested whether the difficulty of predicting contacts depends upon the protein length and the depth of the family sequence alignment. The analyses were carried out on the target domains for which structural homologs did not exist or were difficult to identify. The evaluation was performed for all types of contacts (short, medium, and long-range), with emphasis placed on long-range contacts, i.e. those involving residues separated by at least 24 residues along the sequence. The assessment suggests that the best CASP10 contact prediction methods perform at approximately the same level, and comparably to those participating in CASP9.

ABOUT COMPLEX OPERATIONS IN NON-POSITIONAL RESIDUE NUMBER SYSTEM

Directory of Open Access Journals (Sweden)

Yu. D. Polissky

2016-04-01

Full Text Available Purpose. The purpose of this work is the theoretical substantiation of methods for increased efficiency of execution of difficult, so-called not modular, operations in non-positional residue number system for which it is necessary to know operand digits for all grade levels. Methodology. To achieve the target the numbers are presented in odd module system, while the result of the operation is determined on the basis of establishing the operand parity. The parity is determined by finding the sum modulo for the values of the number positional characteristics for all of its modules. Algorithm of position characteristics includes two types of iteration. The first iteration is to move from this number to a smaller number, in which the remains of one or more modules are equal to zero. This is achieved by subtracting out of all the residues the value of one of them. The second iteration is to move from this number to a smaller number due to exclusion of modules, which residues are zero, by dividing this number by the product of these modules. Iterations are performed until the residues of one, some or all of the modules equal to zero and other modules are excluded. The proposed method is distinguished by its simplicity and allows you to obtain the result of the operation quickly. Findings. There are obtained rather simple solutions of not modular operations for definition of outputs beyond the range of the result of adding or subtracting pairs of numbers, comparing pairs of numbers, determining the number belonging to the specific half of the range, defining parity of numbers presented in non-positional residue number system. Originality. The work offered the new effective approaches to solve the non-modular operations of the non-positional residue number system. It seems appropriate to consider these approaches as research areas to enhance the effectiveness of the modular calculation. Practical value. The above solutions have high performance and can

An integrated unscented kalman filter and relevance vector regression approach for lithium-ion battery remaining useful life and short-term capacity prediction

International Nuclear Information System (INIS)

Zheng, Xiujuan; Fang, Huajing

2015-01-01

The gradual decreasing capacity of lithium-ion batteries can serve as a health indicator for tracking the degradation of lithium-ion batteries. It is important to predict the capacity of a lithium-ion battery for future cycles to assess its health condition and remaining useful life (RUL). In this paper, a novel method is developed using unscented Kalman filter (UKF) with relevance vector regression (RVR) and applied to RUL and short-term capacity prediction of batteries. A RVR model is employed as a nonlinear time-series prediction model to predict the UKF future residuals which otherwise remain zero during the prediction period. Taking the prediction step into account, the predictive value through the RVR method and the latest real residual value constitute the future evolution of the residuals with a time-varying weighting scheme. Next, the future residuals are utilized by UKF to recursively estimate the battery parameters for predicting RUL and short-term capacity. Finally, the performance of the proposed method is validated and compared to other predictors with the experimental data. According to the experimental and analysis results, the proposed approach has high reliability and prediction accuracy, which can be applied to battery monitoring and prognostics, as well as generalized to other prognostic applications. - Highlights: • An integrated method is proposed for RUL prediction as well as short-term capacity prediction. • Relevance vector regression model is employed as a nonlinear time-series prediction model. • Unscented Kalman filter is used to recursively update the states for battery model parameters during the prediction. • A time-varying weighting scheme is utilized to improve the accuracy of the RUL prediction. • The proposed method demonstrates high reliability and prediction accuracy.

Geomorphological hazards in Swat valley, Pakistan

International Nuclear Information System (INIS)

Usman, A.

1999-01-01

This study attempts to describe, interpret and analyze, in depth, the varied geomorphological hazards and their impacts prevailing in the swat valley locate in the northern hilly and mountainous regions of Pakistan. The hills and mountains re zones of high geomorphological activity with rapid rates of weathering, active tectonic activities, abundant precipitation, rapid runoff and heavy sediment transport. Due to the varied topography, lithology, steep slope, erodible soil, heavy winter snowfall and intensive rainfall in the spring and summer seasons, several kinds of geomorphological hazards, such as geomorphic gravitational hazards, Fluvial hazards, Glacial hazards, Geo tectonic hazards, are occurring frequently in swat valley. Amongst them, geomorphic gravitational hazards, such as rock fall rock slide, debris slide mud flow avalanches, are major hazards in mountains and hills while fluvial hazards and sedimentation are mainly confined to the alluvial plain and lowlands of the valley. The Getechtonic hazards, on the other hand, have wide spread distribution in the valley the magnitude and occurrence of each king of hazard is thus, varied according to intensity of process and physical geographic environment. This paper discusses the type distribution and damage due to the various geomorphological hazards and their reduction treatments. The study would to be of particular importance and interest to both natural and social scientists, as well as planner, environmentalists and decision-makers for successful developmental interventions in the region. (author)

Welding hazards

International Nuclear Information System (INIS)

Khan, M.A.

1992-01-01

Welding technology is advancing rapidly in the developed countries and has converted into a science. Welding involving the use of electricity include resistance welding. Welding shops are opened in residential area, which was causing safety hazards, particularly the teenagers and children who eagerly see the welding arc with their naked eyes. There are radiation hazards from ultra violet rays which irritate the skin, eye irritation. Welding arc light of such intensity could damage the eyes. (Orig./A.B.)

Proceedings of the 7. biennial residue-to-revenue residual wood conference 2007

International Nuclear Information System (INIS)

Raulin, J.

2007-01-01

This conference provided information on the highest and best use of residual wood, which is quickly becoming a valuable commodity. Issues concerning forest residues, sawmill wastes, agricultural residues and urban organic materials were discussed along with trends in Canadian surplus mill waste production. The evolving nature and technologies of the biomass business were highlighted with particular focus on how to generate energy and save money through the use of residual wood. Residual wood energy projects and developments in Canada, North America and Europe were outlined along with biomass development in relation to forest fires and insect disturbances. Cogeneration technologies using wood wastes for thermal heat, steam and electricity were also presented, along with transportation fuel technologies for the production of ethanol. It was noted that with the rising cost of energy, the forest industry is seeking energy solutions based on the use of residual wood. The range of economically practical residual wood solutions continues to grow as energy prices increase. The conference was attended by more than 200 delegates from the forest industry, suppliers and government representatives, to discuss policies and procedures currently in place. Industry investment is being stimulated by the potential for biofuels and biochemicals, as well as the co-operation between the forest and energy sectors. The conference featured 23 presentations, of which 12 have been catalogued separately for inclusion in this database. refs., tabs., figs

Quantitative assessment of lipoprotein metabolism by positron emission tomography with an 18F-containing residualizing label

International Nuclear Information System (INIS)

Daugherty, A.; Sobel, B.; Kilbourn, M.R.; Dence, C.S.; Thorpe, S.R.

1992-01-01

Residualizing labels for proteins are designed to remain entrapped within cells following uptake and degradation of the carrier protein. In the present work we report the synthesis of a novel residualizing label, N-lactitol-S-([ 18 F]fluorophenacyl)-cysteamine ([ 18 F]LCSH), and its use for quantifying the accumulation of low density lipoprotein in tissues in vivo by positron emission tomography (PET). The retention of degradation products in tissues from lipoprotein or from other rapidly catabolized protein pharmaceuticals tagged with [ 18 F]LCSH reduces leakage of tracer into the plasma compartment. Thus, residualizing labels provide a valuable tool for enhancing signal-to-noise ratios, even during the relatively short interval of PET studies. (author)

Final hazard classification and auditable safety analysis for the N basin segment

International Nuclear Information System (INIS)

Kloster, G.; Smith, R.I.; Larson, A.R.; Duncan, G.M.

1996-12-01

The purpose of this report is to provide the following: To serve as the auditable safety analysis (ASA) for the N Basin Segment, including both the quiescent state and planned intrusive activities. The ASA is developed through the realistic evaluation of potential hazards that envelope the threat to personnel. The ASA also includes the specification of the programmatic, baseline, and activity- specific controls that are necessary for the protection of workers. To determine and document the final hazard classification (FHC) for the N Basin Segment. The FHC is developed through the use of bounding accident analyses that envelope the potential exposures to personnel. The FHC also includes the specification of the special controls that are necessary to remain within the envelope of those accident analyses

Relative consequences of transporting hazardous materials

International Nuclear Information System (INIS)

Fullwood, R.R.; Rhyne, W.R.; Simmons, J.A.; Reese, R.T.

1980-01-01

The objective of this paper is to discuss methods under study at Transportation Technology Center to develop a perspective on how technical measures of hazard and risk relate to perception of hazards, harm, and risks associated with transporting hazardous materials. This paper is concerned with two major aspects of the relative hazards problem. The first aspect is the analyses of the possible effects associated with exposure to hazardous materials as contained in the following two parts: outlines of possible problems and controversies that could be encountered in the evaluation and comparisons of hazards and risks; and description of the various measures of harm (hazards or dangers) and subsequent comparisons thereof. The second aspect of this paper leads into a presentation of the results of a study which had the following purposes: to develop analytical techniques for a consistent treatment of the phenomenology of the consequences of a release of hazardous materials; to reduce the number of variables in the consequence analyses by development of transportation accident scenarios which have the same meteorological conditions, demography, traffic and population densities, geographical features and other appropriate conditions and to develop consistent methods for presenting the results of studies and analyses that describe the phenomenology and compare hazards. The results of the study are intended to provide a bridge between analytical certainty and perception of the hazards involved. Understanding the differences in perception of hazards resulting from transport of various hazardous materials is fraught with difficulties in isolating the qualitative and quantitative features of the problem. By relating the quantitative impacts of material hazards under identical conditions, it is hoped that the perceived differences in material hazards can be delineated and evaluated

A rapid, solid phase extraction (SPE technique for the extraction and gas chromatographic determination lindane pesticide residue in tissue and milk

Directory of Open Access Journals (Sweden)

Yuningsih

2006-03-01

Full Text Available Organochlorine pesticide contamination in feed can cause residue in animal product (tissue and milk, so its become a problem in food safety. Solid phase extraction (SPE has been carried out for determination organochlorine pesticide residues in food animal production. The technique was rapid, not costly and produce limited amount of hazardous-waste. Samples were homogenized with acetonitrile trough cartridge C18, eluted in fluorocyl column with 2% ether-petroleum or acetonitrile fortissue and milk samples respectively. The recoveries of tissue sample by addition lindane standard solution: 0.50 and 1.00 μg are 85.10 and 103.10% respectively, while that of milk with the addition of 0.50, 1.00 and 1.50 μg are 83.80, 88.69 and 91.24% respectively. Three replicates were carried out for every sample. According of validation criteria of FAO/IAEA the recovery for analysis of pesticide residues was 70-110%. Therefore, the method is applicable.

Pyrolysis of automotive shredder residue for the production of fuel-grade gas

International Nuclear Information System (INIS)

Sharp, L.L.; Ness, R.O. Jr.

1993-01-01

Every year eight to ten million cars and trucks are disposed of by shredding at one of the 200 auto shredders located in the United States. Automotive shredder residue (ASR) is a by-product created in the dismantling of automobiles. Figure 1 illustrates the process by which ASR is generated. An automobile is stripped of useful and/or hazardous items, such as the gas tank, battery, tires, and radiator. Although it is beneficial to have these items removed for safety and environmental concerns, this is not always accomplished. After removal of some or all of these items, the automobile is shredded to provide a material less than 4 inches in size and composed of approximately 50% organic and 50% inorganic fractions. Ferrous scrap is then separated out magnetically. This ferrous scrap supplies the steel industry with 12 to 14 million tons per year for electric arc furnace feedstock. Air cyclone separators isolate a low density open-quotes fluffclose quotes from the nonferrous fraction (aluminum, copper, etc.). This fluff (shredder residue) is composed of a variety of plastics, fabrics, foams, glass, rubber, and an assortment of contaminants. Fluff bulk density is approximately 20 lb/ft

Remaining Sites Verification Package for the 100-D-9 Boiler Fuel Oil Tank Site. Attachment to Waste Site Reclassification Form 2006-030

International Nuclear Information System (INIS)

Dittmer, L.M.

2006-01-01

The 100-D-9 site is the former location of an underground storage tank used for holding fuel for the 184-DA Boiler House. Results of soil-gas samples taken from six soil-gas probes in a rectangle around the site the tank had been removed from concluded that there were no volatile organic compounds at detectable levels in the area. The 100-D-9 Boiler Fuel Oil Tank Site meets the remedial action objectives specified in the Remaining Sites ROD. The results demonstrated that residual contaminant concentrations do not preclude any future uses and allow for unrestricted use of shallow zone soils. The results also demonstrate that residual contaminant concentrations are protective of groundwater and the Columbia River

Seismic hazard assessment: Issues and alternatives

Science.gov (United States)

Wang, Z.

2011-01-01

Seismic hazard and risk are two very important concepts in engineering design and other policy considerations. Although seismic hazard and risk have often been used inter-changeably, they are fundamentally different. Furthermore, seismic risk is more important in engineering design and other policy considerations. Seismic hazard assessment is an effort by earth scientists to quantify seismic hazard and its associated uncertainty in time and space and to provide seismic hazard estimates for seismic risk assessment and other applications. Although seismic hazard assessment is more a scientific issue, it deserves special attention because of its significant implication to society. Two approaches, probabilistic seismic hazard analysis (PSHA) and deterministic seismic hazard analysis (DSHA), are commonly used for seismic hazard assessment. Although PSHA has been pro-claimed as the best approach for seismic hazard assessment, it is scientifically flawed (i.e., the physics and mathematics that PSHA is based on are not valid). Use of PSHA could lead to either unsafe or overly conservative engineering design or public policy, each of which has dire consequences to society. On the other hand, DSHA is a viable approach for seismic hazard assessment even though it has been labeled as unreliable. The biggest drawback of DSHA is that the temporal characteristics (i.e., earthquake frequency of occurrence and the associated uncertainty) are often neglected. An alternative, seismic hazard analysis (SHA), utilizes earthquake science and statistics directly and provides a seismic hazard estimate that can be readily used for seismic risk assessment and other applications. ?? 2010 Springer Basel AG.

Derivation of guidelines for uranium residual radioactive material in soil at the New Brunswick Site, Middlesex County, New Jersey

International Nuclear Information System (INIS)

Dunning, D.; Kamboj, S.; Nimmagadda, M.; Yu, C.

1996-02-01

Residual radioactive material guidelines for uranium in soil were derived for the New Brunswick Site, located in Middlesex County, New Jersey. This site has been designated for remedial action under the Formerly Utilized Sites Remedial Action Program of the US Department of Energy (DOE). Residual radioactive material guidelines for individual radionuclides of concern and total uranium were derived on the basis of the requirement that the 50-year committed effective dose equivalent to a hypothetical individual who lives or works in the immediate vicinity of the New Brunswick Site should not exceed a dose of 30 mrem/yr following remedial action for the current-use and likely future-use scenarios or a dose of 100 mrem/yr for less likely future-use scenarios. The DOE residual radioactive material guideline computer code, RESRAD, was used in this evaluation; RESRAD implements the methodology described in the DOE manual for establishing residual radioactive material guidelines. The guidelines derived in this report are intended to apply to the remediation of these remaining residual radioactive materials at the site. The primary radionuclides of concern in these remaining materials are expected to be radium-226 and, to a lesser extent, natural uranium and thorium. The DOE has established generic cleanup guidelines for radium and thorium in soil; however, cleanup guidelines for other radionuclides must be derived on a site-specific basis

Effect of systematic ergonomic hazard identification and control implementation on musculoskeletal disorder and injury risk.

Science.gov (United States)

Cantley, Linda F; Taiwo, Oyebode A; Galusha, Deron; Barbour, Russell; Slade, Martin D; Tessier-Sherman, Baylah; Cullen, Mark R

2014-01-01

This study aimed to examine the effect of an ergonomic hazard control (HC) initiative, undertaken as part of a company ergonomics standard, on worker injury risk. Using the company's ergonomic hazards database to identify jobs with and without ergonomic HC implementation and linking to individual job and injury histories, injury risk among person-jobs with HC implementation (the HC group) was compared to those without HC (NoHC group) using random coefficient models. Further analysis of the HC group was conducted to determine the effect of additional ergonomic hazards controlled on injury risk. Among 123 jobs at 17 plant locations, 347 ergonomic hazards were quantitatively identified during the study period. HC were implemented for 204 quantified ergonomic hazards in 84 jobs, impacting 10 385 persons (12 967 person-jobs). No HC were implemented for quantified ergonomic hazards in the remaining 39 jobs affecting 4155 persons (5046 person-jobs). Adjusting for age, sex, plant origin, and year to control for any temporal trend in injury risk, the relative risk (RR) for musculoskeletal disorder (MSD) was 0.85 and the RR for any injury or MSD was 0.92 in the HC compared to NoHC group. Among the HC group, each ergonomic hazard controlled was associated with risk reduction for MSD and acute injury outcomes (RR 0.93). Systematic ergonomic HC through participatory ergonomics, as part of a mandatory company ergonomics standard, is associated with MSD and injury risk reduction among workers in jobs with HC implemented.

The new regulations on handling the materials hazardous to water. Consequences for the operation of biowaste processing plants; Die neue Verordnung ueber Anlagen zum Umgang mit wassergefaehrdenden Stoffen. Konsequenzen fuer den Betrieb von Bioabfallbehandlungsanlagen

Energy Technology Data Exchange (ETDEWEB)

Oexle, Anno [Koehler und Klett Rechtsanwaelte Partnerschaft, Koeln (Germany)

2013-07-01

The new regulations on the handling materials hazardous to water include the classification of materials and mixtures, the categorization of wastes, plant specific requirements: general requirements, specific requirements with respect to the capacity of fermentation residual storage.

Solid residues

International Nuclear Information System (INIS)

Mulder, E.; Duin, P.J. van; Grootenboer, G.J.

1995-01-01

A summary is presented of the many investigations that have been done on solid residues of atmospheric fluid bed combustion (AFBC). These residues are bed ash, cyclone ash and bag filter ash. Physical and chemical properties are discussed and then the various uses of residues (in fillers, bricks, gravel, and for recovery of aluminium) are summarised. Toxicological properties of fly ash and stack ash are discussed as are risks of pneumoconiosis for workers handling fly ash, and contamination of water by ashes. On the basis of present information it is concluded that risks to public health from exposure to emissions of coal fly ash from AFBC appear small or negligible as are health risk to workers in the coal fly ash processing industry. 35 refs., 5 figs., 12 tabs

Automatic detection of photoresist residual layer in lithography using a neural classification approach

KAUST Repository

Gereige, Issam

2012-09-01

Photolithography is a fundamental process in the semiconductor industry and it is considered as the key element towards extreme nanoscale integration. In this technique, a polymer photo sensitive mask with the desired patterns is created on the substrate to be etched. Roughly speaking, the areas to be etched are not covered with polymer. Thus, no residual layer should remain on these areas in order to insure an optimal transfer of the patterns on the substrate. In this paper, we propose a nondestructive method based on a classification approach achieved by artificial neural network for automatic residual layer detection from an ellipsometric signature. Only the case of regular defect, i.e. homogenous residual layer, will be considered. The limitation of the method will be discussed. Then, an experimental result on a 400 nm period grating manufactured with nanoimprint lithography is analyzed with our method. © 2012 Elsevier B.V. All rights reserved.

21 CFR 123.6 - Hazard analysis and Hazard Analysis Critical Control Point (HACCP) plan.

Science.gov (United States)

2010-04-01

... Control Point (HACCP) plan. 123.6 Section 123.6 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF... Provisions § 123.6 Hazard analysis and Hazard Analysis Critical Control Point (HACCP) plan. (a) Hazard... fish or fishery product being processed in the absence of those controls. (b) The HACCP plan. Every...

Residual life estimation of electrical insulation system for rotating equipment

International Nuclear Information System (INIS)

Vashishtha, Y.D.; Gupta, A.K.; Bhattacharyya, A.K.; Verma, A.K.

1994-01-01

Residual life assessment gains significance towards the end of designed life for granting plant life extensions and resource planning for costly equipment replacement. A critical review of all the diagnostic techniques presently used to assess either health of insulation system or to infer qualitatively the remaining life for rotating machines is presented. However more emphasis is required on developing quantitative methods. This paper also formulates the experimental plan for progressively censored ageing tests, measurement of partial discharge parameters, micro-structural study for delamination and electrical tree growth and measurement of electrical breakdown strength. Partial discharge (PD) patterns, electrical tree growth and time to failure data shall be taken as training set for the neural network learning which can be useful to predict residual life with only one candidate parameter i.e. PD patterns. (author). 9 refs

Preliminary Performance Assessment for the Waste Management Area C at the Hanford Site in Southeast Washington

International Nuclear Information System (INIS)

Bergeron, Marcel P.; Singleton, Kristin M.; Eberlein, Susan J.

2015-01-01

A performance assessment (PA) of Single-Shell Tank (SST) Waste Management Area C (WMA C) located at the U.S. Department of Energy's (DOE) Hanford Site in southeastern Washington is being conducted to satisfy the requirements of the Hanford Federal Facility Agreement and Consent Order (HFFACO), as well as other Federal requirements and State-approved closure plans and permits. The WMP C PA assesses the fate, transport, and impacts of radionuclides and hazardous chemicals within residual wastes left in tanks and ancillary equipment and facilities in their assumed closed configuration and the subsequent risks to humans into the far future. The part of the PA focused on radiological impacts is being developed to meet the requirements for a closure authorization under DOE Order 435.1 that includes a waste incidental to reprocessing determination for residual wastes remaining in tanks, ancillary equipment, and facilities. An additional part of the PA will evaluate human health and environmental impacts from hazardous chemical inventories in residual wastes remaining in WMA C tanks, ancillary equipment, and facilities needed to meet the requirements for permitted closure under RCRA.

Preliminary Performance Assessment for the Waste Management Area C at the Hanford Site in Southeast Washington

Energy Technology Data Exchange (ETDEWEB)

Bergeron, Marcel P. [Washington River Protection Solutions LLC, Richland, WA (United States); Singleton, Kristin M. [Washington River Protection Solutions LLC, Richland, WA (United States); Eberlein, Susan J. [Washington River Protection Solutions LLC, Richland, WA (United States)

2015-01-07

A performance assessment (PA) of Single-Shell Tank (SST) Waste Management Area C (WMA C) located at the U.S. Department of Energy's (DOE) Hanford Site in southeastern Washington is being conducted to satisfy the requirements of the Hanford Federal Facility Agreement and Consent Order (HFFACO), as well as other Federal requirements and State-approved closure plans and permits. The WMP C PA assesses the fate, transport, and impacts of radionuclides and hazardous chemicals within residual wastes left in tanks and ancillary equipment and facilities in their assumed closed configuration and the subsequent risks to humans into the far future. The part of the PA focused on radiological impacts is being developed to meet the requirements for a closure authorization under DOE Order 435.1 that includes a waste incidental to reprocessing determination for residual wastes remaining in tanks, ancillary equipment, and facilities. An additional part of the PA will evaluate human health and environmental impacts from hazardous chemical inventories in residual wastes remaining in WMA C tanks, ancillary equipment, and facilities needed to meet the requirements for permitted closure under RCRA.

Remaining Sites Verification Package for the 600-233 Waste Site, Vertical Pipe Near 100-B Electrical Laydown Area. Attachment to Waste Site Reclassification Form 2005-041

International Nuclear Information System (INIS)

Carlson, R.A.

2005-01-01

The 600-233 waste site consisted of three small-diameter pipelines within the 600-232 waste site, including previously unknown diesel fuel supply lines discovered during site remediation. The 600-233 waste site has been remediated to achieve the remedial action objectives specified in the Remaining Sites ROD. The results of verification sampling show that residual contaminant concentrations do not preclude any future uses and allow for unrestricted use of shallow zone soils. The results also demonstrate that residual contaminant concentrations are protective of groundwater and the Columbia River

Resilience to Interacting multi-natural hazards

Science.gov (United States)

Zhuo, Lu; Han, Dawei

2016-04-01

Conventional analyses of hazard assessment tend to focus on individual hazards in isolation. However, many parts of the world are usually affected by multiple natural hazards with the potential for interacting relationships. The understanding of such interactions, their impacts and the related uncertainties, are an important and topical area of research. Interacting multi-hazards may appear in different forms, including 1) CASCADING HAZARDS (a primary hazard triggering one or more secondary hazards such as an earthquake triggering landslides which may block river channels with dammed lakes and ensued floods), 2) CONCURRING HAZARDS (two or more primary hazards coinciding to trigger or exacerbate secondary hazards such as an earthquake and a rainfall event simultaneously creating landslides), and 3) ALTERING HAZARDS (a primary hazard increasing the probability of a secondary hazard occurring such as major earthquakes disturbing soil/rock materials by violent ground shaking which alter the regional patterns of landslides and debris flows in the subsequent years to come). All three types of interacting multi-hazards may occur in natural hazard prone regions, so it is important that research on hazard resilience should cover all of them. In the past decades, great progresses have been made in tackling disaster risk around the world. However, there are still many challenging issues to be solved, and the disasters over recent years have clearly demonstrated the inadequate resilience in our highly interconnected and interdependent systems. We have identified the following weaknesses and knowledge gaps in the current disaster risk management: 1) although our understanding in individual hazards has been greatly improved, there is a lack of sound knowledge about mechanisms and processes of interacting multi-hazards. Therefore, the resultant multi-hazard risk is often significantly underestimated with severe consequences. It is also poorly understood about the spatial and

Removal of residual nuclei following a cavitation event using low-amplitude ultrasound.

Science.gov (United States)

Duryea, Alexander P; Cain, Charles A; Tamaddoni, Hedieh A; Roberts, William W; Hall, Timothy L

2014-10-01

Microscopic residual bubble nuclei can persist on the order of 1 s following a cavitation event. These bubbles can limit the efficacy of ultrasound therapies such as shock wave lithotripsy and histotripsy, because they attenuate pulses that arrive subsequent to their formation and seed repetitive cavitation activity at a discrete set of sites (cavitation memory). Here, we explore a strategy for the removal of these residual bubbles following a cavitation event, using low-amplitude ultrasound pulses to stimulate bubble coalescence. All experiments were conducted in degassed water and monitored using high-speed photography. In each case, a 2-MHz histotripsy transducer was used to initiate cavitation activity (a cavitational bubble cloud), the collapse of which generated a population of residual bubble nuclei. This residual nuclei population was then sonicated using a 1 ms pulse from a separate 500-kHz transducer, which we term the bubble removal pulse. Bubble removal pulse amplitudes ranging from 0 to 1.7 MPa were tested, and the backlit area of shadow from bubbles remaining in the field following bubble removal was calculated to quantify efficacy. It was found that an ideal amplitude range exists (roughly 180 to 570 kPa) in which bubble removal pulses stimulate the aggregation and subsequent coalescence of residual bubble nuclei, effectively removing them from the field. Further optimization of bubble removal pulse sequences stands to provide an adjunct to cavitation-based ultrasound therapies such as shock wave lithotripsy and histotripsy, mitigating the effects of residual bubble nuclei that currently limit their efficacy.

Hazardous materials and waste management a guide for the professional hazards manager

CERN Document Server

Cheremisinoff, Nicholas P

1995-01-01

The management of hazardous materials and industrial wastes is complex, requiring a high degree of knowledge over very broad technical and legal subject areas. Hazardous wastes and materials are diverse, with compositions and properties that not only vary significantly between industries, but within industries, and indeed within the complexity of single facilities. Proper management not only requires an understanding of the numerous and complex regulations governing hazardous materials and waste streams, but an understanding and knowledge of the treatment, post-treatment, and waste minimizatio

Residue Geometry Networks: A Rigidity-Based Approach to the Amino Acid Network and Evolutionary Rate Analysis

Science.gov (United States)

Fokas, Alexander S.; Cole, Daniel J.; Ahnert, Sebastian E.; Chin, Alex W.

2016-01-01

Amino acid networks (AANs) abstract the protein structure by recording the amino acid contacts and can provide insight into protein function. Herein, we describe a novel AAN construction technique that employs the rigidity analysis tool, FIRST, to build the AAN, which we refer to as the residue geometry network (RGN). We show that this new construction can be combined with network theory methods to include the effects of allowed conformal motions and local chemical environments. Importantly, this is done without costly molecular dynamics simulations required by other AAN-related methods, which allows us to analyse large proteins and/or data sets. We have calculated the centrality of the residues belonging to 795 proteins. The results display a strong, negative correlation between residue centrality and the evolutionary rate. Furthermore, among residues with high closeness, those with low degree were particularly strongly conserved. Random walk simulations using the RGN were also successful in identifying allosteric residues in proteins involved in GPCR signalling. The dynamic function of these residues largely remain hidden in the traditional distance-cutoff construction technique. Despite being constructed from only the crystal structure, the results in this paper suggests that the RGN can identify residues that fulfil a dynamical function. PMID:27623708

Hazards in the chemical laboratory

International Nuclear Information System (INIS)

Bretherick, L.

1987-01-01

The contents of this book are: Preface; Introduction; Health and Safety at Work Act 1974; Safety Planning and Management; Fire Protection; Reactive Chemical Hazards; Chemical Hazards and Toxicology; Health Care and First Aid; Hazardous Chemicals; Precautions against Radiations; and An American View

Pencil kernel correction and residual error estimation for quality-index-based dose calculations

International Nuclear Information System (INIS)

Nyholm, Tufve; Olofsson, Joergen; Ahnesjoe, Anders; Georg, Dietmar; Karlsson, Mikael

2006-01-01

Experimental data from 593 photon beams were used to quantify the errors in dose calculations using a previously published pencil kernel model. A correction of the kernel was derived in order to remove the observed systematic errors. The remaining residual error for individual beams was modelled through uncertainty associated with the kernel model. The methods were tested against an independent set of measurements. No significant systematic error was observed in the calculations using the derived correction of the kernel and the remaining random errors were found to be adequately predicted by the proposed method

Change of residual stresses during plastic deformation under uniaxial tension test; Variacion de las tensiones residuales con la deformacion plastica en el ensayo de traccion

Energy Technology Data Exchange (ETDEWEB)

Benito, J. A.; Jorba, J.; Roca, A.

2001-07-01

Hang of longitudinal and transverse residual stresses was studied by X Ray diffraction method as the applied plastic deformation, measured as A% was increased in a standard tension test. The starting material, hot rolling Armco iron, has values close to 0 MPa in longitudinal direction. But it reaches 600 MPa with only A=1,5%, this value remains constant until necking is produced. In transverse direction the stating values are 300 MPa, changes are small and residual stresses remain compressive until the end of tension test. In addition, studies of the changes of residual stresses with time and with misalignment between incident X Ray and drawing direction are presented. (Author) 5 refs.

Investigation of the possibility of using residual heat reactor energy

Science.gov (United States)

Aminov, R. Z.; Yurin, V. E.; Bessonov, V. N.

2017-11-01

The largest contribution to the probable frequency of core damage is blackout events. The main component of the heat capacity at each reactor within a few minutes following a blackout is the heat resulting from the braking of beta-particles and the transfer of gamma-ray energy by the fission fragments and their decay products, which is known as the residual heat. The power of the residual heat changes gradually over a long period of time and for a VVER-1000 reactor is about 15-20 MW of thermal power over 72 hours. Current cooldown systems increase the cost of the basic nuclear power plants (NPP) funds without changing the amount of electricity generated. Such systems remain on standby, accelerating the aging of the equipment and accordingly reducing its reliability. The probability of system failure increases with the duration of idle time. Furthermore, the reactor residual heat energy is not used. A proposed system for cooling nuclear power plants involves the use of residual thermal power to supply the station’s own needs in emergency situations accompanied by a complete blackout. The thermal power of residual heat can be converted to electrical energy through an additional low power steam turbine. In normal mode, the additional steam turbine generates electricity, which makes it possible to ensure spare NPP and a return on the investment in the reservation system. In this work, experimental data obtained from a Balakovo NPP was analyzed to determine the admissibility of cooldown of the reactors through the 2nd circuit over a long time period, while maintaining high-level parameters for the steam generated by the steam generators.

St. Louis area earthquake hazards mapping project; seismic and liquefaction hazard maps

Science.gov (United States)

Cramer, Chris H.; Bauer, Robert A.; Chung, Jae-won; Rogers, David; Pierce, Larry; Voigt, Vicki; Mitchell, Brad; Gaunt, David; Williams, Robert; Hoffman, David; Hempen, Gregory L.; Steckel, Phyllis; Boyd, Oliver; Watkins, Connor M.; Tucker, Kathleen; McCallister, Natasha

2016-01-01

We present probabilistic and deterministic seismic and liquefaction hazard maps for the densely populated St. Louis metropolitan area that account for the expected effects of surficial geology on earthquake ground shaking. Hazard calculations were based on a map grid of 0.005°, or about every 500 m, and are thus higher in resolution than any earlier studies. To estimate ground motions at the surface of the model (e.g., site amplification), we used a new detailed near‐surface shear‐wave velocity model in a 1D equivalent‐linear response analysis. When compared with the 2014 U.S. Geological Survey (USGS) National Seismic Hazard Model, which uses a uniform firm‐rock‐site condition, the new probabilistic seismic‐hazard estimates document much more variability. Hazard levels for upland sites (consisting of bedrock and weathered bedrock overlain by loess‐covered till and drift deposits), show up to twice the ground‐motion values for peak ground acceleration (PGA), and similar ground‐motion values for 1.0 s spectral acceleration (SA). Probabilistic ground‐motion levels for lowland alluvial floodplain sites (generally the 20–40‐m‐thick modern Mississippi and Missouri River floodplain deposits overlying bedrock) exhibit up to twice the ground‐motion levels for PGA, and up to three times the ground‐motion levels for 1.0 s SA. Liquefaction probability curves were developed from available standard penetration test data assuming typical lowland and upland water table levels. A simplified liquefaction hazard map was created from the 5%‐in‐50‐year probabilistic ground‐shaking model. The liquefaction hazard ranges from low (60% of area expected to liquefy) in the lowlands. Because many transportation routes, power and gas transmission lines, and population centers exist in or on the highly susceptible lowland alluvium, these areas in the St. Louis region are at significant potential risk from seismically induced liquefaction and associated

Hazardous solvent substitution

International Nuclear Information System (INIS)

Twitchell, K.E.

1995-01-01

This article is an overview of efforts at INEL to reduce the generation of hazardous wastes through the elimination of hazardous solvents. To aid in their efforts, a number of databases have been developed and will become a part of an Integrated Solvent Substitution Data System. This latter data system will be accessible through Internet

Modified hazard ranking system for sites with mixed radioactive and hazardous wastes. User manual

International Nuclear Information System (INIS)

Hawley, K.A.; Peloquin, R.A.; Stenner, R.D.

1986-04-01

This document describes both the original Hazard Ranking System and the modified Hazard Ranking System as they are to be used in evaluating the relative potential for uncontrolled hazardous substance facilities to cause human health or safety problems or ecological or environmental damage. Detailed instructions for using the mHRS/HRS computer code are provided, along with instructions for performing the calculations by hand. Uniform application of the ranking system will permit the DOE to identify those releases of hazardous substances that pose the greatest hazard to humans or the environment. However, the mHRS/HRS by itself cannot establish priorities for the allocation of funds for remedial action. The mHRS/HRS is a means for applying uniform technical judgment regarding the potential hazards presented by a facility relative to other facilities. It does not address the feasibility, desirability, or degree of cleanup required. Neither does it deal with the readiness or ability of a state to carry out such remedial action, as may be indicated, or to meet other conditions prescribed in CERCLA. 13 refs., 13 figs., 27 tabs

Modified hazard ranking system for sites with mixed radioactive and hazardous wastes. User manual.

Energy Technology Data Exchange (ETDEWEB)

Hawley, K.A.; Peloquin, R.A.; Stenner, R.D.

1986-04-01

This document describes both the original Hazard Ranking System and the modified Hazard Ranking System as they are to be used in evaluating the relative potential for uncontrolled hazardous substance facilities to cause human health or safety problems or ecological or environmental damage. Detailed instructions for using the mHRS/HRS computer code are provided, along with instructions for performing the calculations by hand. Uniform application of the ranking system will permit the DOE to identify those releases of hazardous substances that pose the greatest hazard to humans or the environment. However, the mHRS/HRS by itself cannot establish priorities for the allocation of funds for remedial action. The mHRS/HRS is a means for applying uniform technical judgment regarding the potential hazards presented by a facility relative to other facilities. It does not address the feasibility, desirability, or degree of cleanup required. Neither does it deal with the readiness or ability of a state to carry out such remedial action, as may be indicated, or to meet other conditions prescribed in CERCLA. 13 refs., 13 figs., 27 tabs.

Hazardous solvent substitution

International Nuclear Information System (INIS)

Twitchell, K.E.

1995-01-01

Eliminating hazardous solvents is good for the environment, worker safety, and the bottom line. However, even though we are motivated to find replacements, the big question is 'What can we use as replacements for hazardous solvents?'You, too, can find replacements for your hazardous solvents. All you have to do is search for them. Search through the vendor literature of hundreds of companies with thousands of products. Ponder the associated material safety data sheets, assuming of course that you can obtain them and, having obtained them, that you can read them. You will want to search the trade magazines and other sources for product reviews. You will want to talk to users about how well the product actually works. You may also want to check US Environmental Protection Agency (EPA) and other government reports for toxicity and other safety information. And, of course, you will want to compare the product's constituent chemicals with the many hazardous constituency lists to ensure the safe and legal use of the product in your workplace

Estimating residual life of alloy 600 RPV penetrations

International Nuclear Information System (INIS)

Hunt, E.S.; White, G.A.; Pathania, R.; Arey, M.L.; Whitaker, D.E.

1996-01-01

Primary water stress corrosion cracking (PWSCC) of Alloy 600 penetrations PWR in reactor pressure vessel (RPV) heads has become a significant economic concern worldwide. PWSCC of these penetrations has led to extended maintenance outages, expensive inspections and repairs, and in some cases, replacement of the entire vessel head. This paper describes methodology developed to predict the remaining life of Alloy 600 penetrations in reactor vessel heads. Predictions of remaining life are an important input to planning models used by utilities to select a strategy for responding to the PWSCC issue at the lowest life cycle cost with an acceptably low risk of leakage. The remaining life of RPV penetrations is determined using the results of inspections of penetrations and statistical methods to predict future degradation. The analysis takes into account the effects of material properties, welding residual stresses, and operating temperature on PWSCC initiation and growth. The probability of developing cracks of various depths is assessed using Monte Carlo methods which provide for uncertainties in the input assumptions. For plants which have not yet performed inspections, remaining life predictions are based on inspection results from similar plants which have performed inspections with corrections made for known differences in design details, material properties and operating conditions

Urbanization as Socioenvironmental Succession: The Case of Hazardous Industrial Site Accumulation.

Science.gov (United States)

Elliott, James R; Frickel, Scott

2015-05-01

This study rehabilitates concepts from classical human ecology and synthesizes them with contemporary urban and environmental sociology to advance a theory of urbanization as socioenvironmental succession. The theory illuminates how social and biophysical phenomena interact endogenously at the local level to situate urban land use patterns recursively and reciprocally in place. To demonstrate this theory we conduct a historical-comparative analysis of hazardous industrial site accumulation in four U.S. cities, using a relational database that was assembled for more than 11,000 facilities that operated during the past half century--most of which remain unacknowledged in government reports. Results show how three iterative processes--hazardous industrial churning, residential churning, and risk containment--intersect to produce successive socioenvironmental changes that are highly relevant to but often missed by research on urban growth machines, environmental inequality, and systemic risk.

Risk assessment and risk management at the Canadian Food Inspection Agency (CFIA): a perspective on the monitoring of foods for chemical residues.

Science.gov (United States)

Bietlot, Henri P; Kolakowski, Beata

2012-08-01

The Canadian Food Inspection Agency (CFIA) uses 'Ranked Risk Assessment' (RRA) to prioritize chemical hazards for inclusion in monitoring programmes or method development projects based on their relative risk. The relative risk is calculated for a chemical by scoring toxicity and exposure in the 'risk model scoring system' of the Risk Priority Compound List (RPCL). The relative ranking and the risk management options are maintained and updated in the RPCL. The ranking may be refined by the data generated by the sampling and testing programs. The two principal sampling and testing programmes are the National Chemical Residue Monitoring Program (NCRMP) and the Food Safety Action Plan (FSAP). The NCRMP sampling plans focus on the analysis of federally registered products (dairy, eggs, honey, meat and poultry, fresh and processed fruit and vegetable commodities, and maple syrup) for residues of veterinary drugs, pesticides, environmental contaminants, mycotoxins, and metals. The NCRMP is complemented by the Food Safety Action Plan (FSAP) targeted surveys. These surveys focus on emerging chemical hazards associated with specific foods or geographical regions for which applicable maximum residue limits (MRLs) are not set. The data from the NCRMP and FSAP also influence the risk management (follow-up) options. Follow-up actions vary according to the magnitude of the health risk, all with the objective of preventing any repeat occurrence to minimize consumer exposure to a product representing a potential risk to human health. © Her Majesty the Queen in Right of Canada 2012. Drug Testing and Analysis © 2012 John Wiley & Sons, Ltd.

Radon and its hazards

International Nuclear Information System (INIS)

Chang Guilan

2002-01-01

The author describes basic physical and chemical properties of radon and the emanation, introduces methods of radon measurement, expounds the hazards of non-mine radon accumulation to the health of human being and the protection, as well as the history how the human being recognizes the hazards of radon through the specific data and examples, and finally proposes protecting measures to avoid the hazards of radon to the health of human being, and to do ecologic evaluation of environments

Industrial hazard and safety handbook

CERN Document Server

King, Ralph W

1979-01-01

Industrial Hazard and Safety Handbook (Revised Impression) describes and exposes the main hazards found in industry, with emphasis on how these hazards arise, are ignored, are identified, are eliminated, or are controlled. These hazard conditions can be due to human stresses (for example, insomnia), unsatisfactory working environments, as well as secret industrial processes. The book reviews the cost of accidents, human factors, inspections, insurance, legal aspects, planning for major emergencies, organization, and safety measures. The text discusses regulations, codes of practice, site layou

Global Landslide Hazard Distribution

Data.gov (United States)

National Aeronautics and Space Administration — Global Landslide Hazard Distribution is a 2.5 minute grid of global landslide and snow avalanche hazards based upon work of the Norwegian Geotechnical Institute...

Performance evaluation of the PITBULL trademark pump for the removal of hazardous waste

International Nuclear Information System (INIS)

Hatchell, B.K.; Combs, W.H.; Hymas, C.R.; Powell, M.R.; Rinker, M.W.; White, M.

1998-09-01

One objective of the Waste Removal Project at the Department of Energy's Savannah River Site (SRS) is to explore methods to successfully remove waste heels that will remain in the high-level waste tanks after bulk waste removal has been completed. Tank closure is not possible unless this residue is removed. As much as 151,000 liters of residue can remain after a conventional waste removal campaign. The waste heels can be comprised of sludge, zeolite, and silica. The heels are generally hardened or compacted insoluble particulate with relatively rapid settling velocities. A PITBULL trademark pump is being considered by SRS to retrieve sludge-type waste from Tank 19. Sections 1 through 4 of this report present the scope and objectives of the test program, describe the principles of operation of the PITBULL, and present the test approach, set-up, and instrumentation. Test results, including pumping rates with water and slurry, are provided in Section 5, along with considerations for remote operation. Conclusions and recommendations are provided in Section 6

A two-stage bioprocess for hydrogen and methane production from rice straw bioethanol residues.

Science.gov (United States)

Cheng, Hai-Hsuan; Whang, Liang-Ming; Wu, Chao-Wei; Chung, Man-Chien

2012-06-01

This study evaluates a two-stage bioprocess for recovering hydrogen and methane while treating organic residues of fermentative bioethanol from rice straw. The obtained results indicate that controlling a proper volumetric loading rate, substrate-to-biomass ratio, or F/M ratio is important to maximizing biohydrogen production from rice straw bioethanol residues. Clostridium tyrobutyricum, the identified major hydrogen-producing bacteria enriched in the hydrogen bioreactor, is likely utilizing lactate and acetate for biohydrogen production. The occurrence of acetogenesis during biohydrogen fermentation may reduce the B/A ratio and lead to a lower hydrogen production. Organic residues remained in the effluent of hydrogen bioreactor can be effectively converted to methane with a rate of 2.8 mmol CH(4)/gVSS/h at VLR of 4.6 kg COD/m(3)/d. Finally, approximately 75% of COD in rice straw bioethanol residues can be removed and among that 1.3% and 66.1% of COD can be recovered in the forms of hydrogen and methane, respectively. Copyright © 2012 Elsevier Ltd. All rights reserved.

Natural Hazards, Second Edition

Science.gov (United States)

Rouhban, Badaoui