WorldWideScience

Sample records for residual gas levels

  1. Residual gas analysis

    International Nuclear Information System (INIS)

    Berecz, I.

    1982-01-01

    Determination of the residual gas composition in vacuum systems by a special mass spectrometric method was presented. The quadrupole mass spectrometer (QMS) and its application in thin film technology was discussed. Results, partial pressure versus time curves as well as the line spectra of the residual gases in case of the vaporization of a Ti-Pd-Au alloy were demonstrated together with the possible construction schemes of QMS residual gas analysers. (Sz.J.)

  2. RESIDUAL RISK ASSESSMENT: GAS DISTRIBUTION STAGE ...

    Science.gov (United States)

    This document describes the residual risk assessment for the Gas Distribution Stage 1 souce category. For stationary sources, section 112 (f) of the Clean Air Act requires EPA to assess risks to human health and the environment following implementation of technology-based control standards. If these technology-based control standards do not provide an ample margin of safety, then EPA is required to promulgate addtional standards. This document describes the methodology and results of the residual risk assessment performed for the Gas Distribution Stage 1 source category. The results of this analyiss will assist EPA in determining whether a residual risk rule for this source category is appropriate.

  3. Assessment of Pesticide Residue Levels in Vegetables sold in some ...

    African Journals Online (AJOL)

    This study investigated pesticide residue levels in the two vegetables commonly eaten in Lagos state Nigeria. The vegetables (Telfairia occidentalis and Celosia argentea) were purchased from six markets (Oyingbo, Mile 12, Mushin, Ajah, Agege and Festac) in Lagos. The pesticide residue levels were determined using gas ...

  4. Profile Monitors Based on Residual Gas Interaction

    CERN Document Server

    Forck, P; Giacomini, T; Peters, A

    2005-01-01

    The precise determination of transverse beam profiles at high current hadron accelerators has to be performed non-interceptingly. Two methods will be discussed based on the excitation of the residual gas molecules by the beam particles: Firstly, by beam induced fluorescence (BIF) light is emitted from the residual gas molecules and is observed with an image intensified CCD camera. At most laboratories N2 gas is inserted, which has a large cross section for emission in the blue wave length region. Secondly, a larger signal strength is achieved by detecting the ionization products in an Ionization Profile Monitor (IPM). By applying an electric field all ionization products are accelerated toward a spatial resolving Micro-Channel Plate. The signal read-out can either be performed by observing the light from a phosphor screen behind the MCP or electronically by a wire array. Methods to achieve a high spatial resolution and a fast turn-by-turn readout capability are discussed. Even though various approaches at dif...

  5. Chloroxyanion Residue Quantification in Cantaloupes Treated with Chlorine Dioxide Gas.

    Science.gov (United States)

    Kaur, Simran; Smith, David J; Morgan, Mark T

    2015-09-01

    Previous studies show that treatment of cantaloupes with chlorine dioxide (ClO2) gas at 5 mg/liter for 10 min results in a significant reduction (P chlorine dioxide ((36)ClO2) gas was used to describe the identity and distribution of chloroxyanion residues in or on cantaloupe subsequent to fumigation with ClO2 gas at a mean concentration of 5.1 ± 0.7 mg/liter for 10 min. Each treated cantaloupe was separated into rind, flesh, and mixed (rind and flesh) sections, which were blended and centrifuged to give the corresponding sera fractions. Radioactivity detected, ratio of radioactivity to mass of chlorite in initial ClO2 gas generation reaction, and distribution of chloroxyanions in serum samples were used to calculate residue concentrations in flesh, rind, and mixed samples. Anions detected on the cantaloupe were Cl(-) (∼ 90%) and ClO3(-) (∼ 10%), located primarily in the rind (19.3 ± 8.0 μg of Cl(-)/g of rind and 4.8 ± 2.3 μg of ClO3(-)/g of rind, n = 6). Cantaloupe flesh (∼ 200 g) directly exposed to(36)ClO2 gas treatment showed the presence of only Cl(-) residues (8.1 ± 1.0 μg of Cl(-)/g of flesh, n = 3). Results indicate chloroxyanion residues Cl(-) and ClO3(-) are only present on the rind of whole cantaloupes treated with ClO2 gas. However during cutting, residues may be transferred to the fruit flesh. Because Cl(-) is not toxic, only ClO3(-) would be a toxicity concern, but the levels transferred from rind to flesh are very low. In the case of fruit flesh directly exposed to ClO2 gas, only nontoxic Cl(-) was detected. This indicates that ClO2 gas that comes into contact with edible flesh would not pose a health concern.

  6. An accurate, residue-level, pair potential of mean force for folding and binding based on the distance-scaled, ideal-gas reference state.

    Science.gov (United States)

    Zhang, Chi; Liu, Song; Zhou, Hongyi; Zhou, Yaoqi

    2004-02-01

    Structure prediction on a genomic scale requires a simplified energy function that can efficiently sample the conformational space of polypeptide chains. A good energy function at minimum should discriminate native structures against decoys. Here, we show that a recently developed, residue-specific, all-atom knowledge-based potential (167 atomic types) based on distance-scaled, finite ideal-gas reference state (DFIRE-all-atom) can be substantially simplified to 20 residue types located at side-chain center of mass (DFIRE-SCM) without a significant change in its capability of structure discrimination. Using 96 standard multiple decoy sets, we show that there is only a small reduction (from 80% to 78%) in success rate of ranking native structures as the top 1. The success rate is higher than two previously developed, all-atom distance-dependent statistical pair potentials. Applied to structure selections of 21 docking decoys without modification, the DFIRE-SCM potential is 29% more successful in recognizing native complex structures than an all-atom statistical potential trained by a database of dimeric interfaces. The potential also achieves 92% accuracy in distinguishing true dimeric interfaces from artificial crystal interfaces. In addition, the DFIRE potential with the C(alpha) positions as the interaction centers recognizes 123 native structures out of a comprehensive 125-protein TOUCHSTONE decoy set in which each protein has 24,000 decoys with only C(alpha) positions. Furthermore, the performance by DFIRE-SCM on newly established 25 monomeric and 31 docking Rosetta-decoy sets is comparable to (or better than in the case of monomeric decoy sets) that of a recently developed, all-atom Rosetta energy function enhanced with an orientation-dependent hydrogen bonding potential.

  7. The new method for the residual gas density measurements

    CERN Document Server

    Anashin, V V; Krasnov, A A; Malyshev, O B; Nas'mov, V P; Pyata, E I; Shaftan, T V

    2001-01-01

    A new method of measurement for residual gas density in the vacuum chambers in presence of synchrotron radiation (SR) is described. The method is based on using a photomultiplier tube for the detection of the SR-stimulated residual gas luminescence, which is proportional to the residual gas density and SR intensity. The design of the experimental setup and results of the measurements of densities of residual gases (H sub 2 , CO sub 2 , CO, N sub 2 , Ar and O sub 2) are submitted.

  8. Determination of low-level agricultural residues in soft drinks and sports drinks by gas chromatography with mass-selective detection: single-laboratory validation.

    Science.gov (United States)

    Paske, Nathan; Berry, Bryan; Schmitz, John; Sullivan, Darryl

    2007-01-01

    In this study, sponsored by PepsiCo Inc., a method was validated for measurement of 19 pesticide residues in soft drinks and sports drinks by gas chromatography/mass spectrometry (GC/MS) with mass selective detection The pesticide residues determined in this validation were alpha-benzenehexachloride (BHC); beta-BHC; gamma-BHC; delta-BHC; methyl parathion; malathion; chlorpyrifos; aldrin; 2,4-dichlorodiphenyldichloroethylene (DDE); alpha-endosulfan; 4,4-DDE; 2,4-dichlorodiphenyldichloroethane (DDD); dieldrin; ethion; 4,4-DDD; 2,4-dichlorodiphenyltrichloroethylene (DDT); beta-endosulfan; 4,4-DDT; and endosulfan sulfate when spiked into a 200 mL matrix sample at 0.50 microg/L. The samples were diluted with acetonitrile and water, then liquid-liquid phase extracted into petroleum ether. The resulting extract was concentrated to near dryness and diluted with hexane:dichloromethane (50:50). The concentrated samples were purified by gel permeation chromatography. The resulting solution was concentrated and separated on a Florisil substrate. The eluent was concentrated to near dryness, reconstituted to produce a 200-fold concentration, and analyzed using a GC/MS instrument operated in the selective ion monitoring mode. The GC/MS instrument was equipped with a large volume injector capable of injecting 25 microL. External standards prepared in dichloromethane were used for quantification without the need for matrix-matched calibration because the extraction step minimized the matrix effects. The calibration curves for all agricultural residues had coefficients of determination (r2) of greater than or equal to 0.9900, with the exception of one value that was 0.988. Fortification spikes at 0.50 microg/L in 3 matrixes (7UP, Gatorade, and Diet Pepsi) over the course of 2 days (4 days for Gatorade), where n=8 each day, yielded average percent recoveries (and percent relative standard deviations) as follows (n=64): 95.6 (24.8) for alpha-BHC; 91.9 (23.6) for beta-BHC; 89.1 (21

  9. Low-level Determination of Residual Methyl Methane Sulfonate and Ethyl Methane Sulfonate in Pharmaceuticals by Gas Chromatography with Mass Spectrometry

    Directory of Open Access Journals (Sweden)

    M. Sarat

    2010-01-01

    Full Text Available A capillary gas chromatographic method using mass spectrometric detection was developed and validated for the trace analysis (ppm level of methyl methane sulfonate and ethyl methane sulfonate in pharmaceutical drug substances. The method utilizes a capillary column (DB-624 with 6% cyanopropyl phenyl and 94% dimethyl polysiloxane stationary phase. A dissolve-and-injection approach was adopted for sample introduction in a split less mode. Mixture of (80:20 ratio of methanol and chloroform was used as a diluent or sample solvent. A limit of detection of about 0.17 μg/g (0.17 ppm for methyl methane sulfonate and 0.18 μg/g (0.18 ppm for ethyl methane sulfonate were achieved and limit of quantitation of 0.52 μg/g (0.52 ppm for methyl methane sulfonate and 0.54 μg/g (0.54 ppm for ethyl methane sulfonate were achieved for alkyl sulfonates in drug substance samples.

  10. Gas composition of sludge residue profiles in a sludge treatment reed bed between loadings

    DEFF Research Database (Denmark)

    Larsen, Julie Dam; Nielsen, Steen M; Scheutz, Charlotte

    2017-01-01

    Treatment of sludge in sludge treatment reed bed systems includes dewatering and mineralization. The mineralization process, which is driven by microorganisms, produces different gas species as by-products. The pore space composition of the gas species provides useful information on the biological...... processes occurring in the sludge residue. In this study, we measured the change in composition of gas species in the pore space at different depth levels in vertical sludge residue profiles during a resting period of 32 days. The gas composition of the pore space in the sludge residue changed during...... the resting period. As the resting period proceeded, atmospheric air re-entered the pore space at all depth levels. The methane (CH4) concentration was at its highest during the first part of the resting period, and then declined as the sludge residue became more dewatered and thereby aerated. In the pore...

  11. A modeled experiment of gas behavior in aquifer and residual gas formation

    Science.gov (United States)

    Takahashi, K.; Yamada, Y.; Murata, S.; Nakano, M.; Matsuoka, T.

    2007-12-01

    National and international concern is rising about the possible effects of greenhouse gases (GHGs) on the climate. Several methods are proposed to reduce the gas in the atmosphere and underground sequestration is recently expected as an effective concept. Especially, residual gas can be the most effective method to store the gas in reservoir. Underground sequestration requires the gas injected into a reservoir. When the gas is injected into a water- saturated aquifer, it pushes water out of the pore space. As the gas bubbles go upward, the gas space is filled with water again, but small gas bubbles are trapped in the pore space by surface force and capillary pressure of water. This is the residual gas formation. Once the residual gas is formed, it seldom moves again from the pore space. Residual gas formation needs neither cap-rock nor structural trap, thus has a potential to be applied to broader regions. The purpose of this study is to examine the fundamental mechanism of residual gas formation and gas migration underground by injecting the gas into a modeled and visualized aquifer. We designed and constructed an experimental apparatus to measure the distribution and the saturation of the residual gas. We used glass beads of 1 or 2mm diameters as porous media to construct some reservoir models that have various porosity, permeability, and wettability. The glass beads packed in our apparatus which has 30cm width, 33.5cm height, and 1cm thickness. It has 1§¤volume in amount. The pore space was filled with viscous liquid, then air was injected from the bottom. Some conditions in the injection time and rate were tested. We observed air behavior and measured the volume of the distribution area of residual gas from its digital photographs, and the volume of residual gas from the amount of water that was pushed out from the apparatus. The experimental results showed that differences of reservoir properties made changes in the gas behavior and residual gas volume. It

  12. Graphic Three-Axes Presentation of Residual Gas Analyser Data

    Science.gov (United States)

    Johnson, Kenneth R.; Levi, Alejandro G.

    1996-01-01

    Residual gas analyzers (RGA) are commonly used to measure the composition of residual gases in thermal-vacuum test chambers. Measurements from RGAs are often used to identify and quantify outgassing contaminants from a test article during thermal-vacuum testing. RGA data is typically displayed as snapshots in time, showing instantaneous concentrations of ions from ionized residual gas molecules at different atomic masses. A method was devised by the authors to present RGA data in a three-axis format, plotting atomic mass unit (AMU), ion concentration as a function of AMU, and time, to provide a clear graphic visualization ot trends in gas concentration changes and to initiate a valuable analytical tool to interpret test article outgassing rates during thermal-vacuum testing.

  13. Evaluation of chlorine dioxide gas residues on selected food produce.

    Science.gov (United States)

    Trinetta, Valentina; Vaidya, Nirupama; Linton, Richard; Morgan, Mark

    2011-01-01

    In recent years, the consumption of fresh fruits and vegetables has greatly increased, and so has its association with contamination of several foodborne pathogens (Listeria, Salmonella, and Escherichia coli). Hence, there is a need to investigate effective sanitizer systems for produce decontamination. Chlorine dioxide (ClO(2)), a strong oxidizing gas with broad spectrum and sanitizing properties, has previously been studied for use on selected fruits and vegetables. ClO(2) gas treatments show great potential for surface pathogen reduction; however its use from a residue safety standpoint has yet to be assessed. Thus, the objective of this study was to evaluate residues of ClO(2), chlorite, chlorate, and chloride on selected fresh produce surfaces after treatment with ClO(2) gas. A rinse procedure was used and water samples were analyzed by N, N-diethyl-p-phenylenediamine and ion chromatography method (300.0). Seven different foods--tomatoes, oranges, apples, strawberries, lettuce, alfalfa sprouts, and cantaloupe--were analyzed after ClO(2) treatment for surface residues. Very low residues were detectable for all the food products except lettuce and alfalfa sprouts, where the measured concentrations were significantly higher. Chlorine dioxide technology leaves minimal to no detectable chemical residues in several food products, thus result in no significant risks to consumers. Practical Application: Potential for chlorine dioxide gas treatments as an effective pathogen inactivation technology to produce with minimal risk for consumers.

  14. Residue management in the Bolivia-Brazil gas pipeline construction

    International Nuclear Information System (INIS)

    Freitas, Eduardo Lopes; Henrique, Paulo Roberto Pereira; Cantarino, Anderson Americo Alves

    2000-01-01

    The construction of the gas pipeline is a process sequential of assembly phases, where each one of those phases generates residues of the most varied types and amounts, being necessary the forecast of your generation in agreement with the activity that is being executed. During the accomplishment of the works they are generated a lot of times situations where are observed the inadequate disposition of the residues. Those practices, besides the environmental impact that they cause, it can cart in the future, the need of additional investments be proceeded in the recovery of the areas and removal of the residues. This work presents the Program of administration of Residues instituted during the construction of the pipeline Bolivia - Brazil, seeking, on a side to reduce to the minimum the generation of residues and of the other, moths handling guidelines and disposition, in way to minimize the environmental impacts caused by the same ones. (author)

  15. Pesticides residue levels in selected fruits from some Ghanaian markets

    International Nuclear Information System (INIS)

    Bempah, K.C.

    2009-02-01

    The amount of some pesticide residues in fruits was monitored at five (5) Accra Metropolis markets. Locally produced fruits (pawpaw and tomato) and imported apples were purchased from two supermarkets and three urban markets in Accra metropolis and analyzed by gas chromatography equipped with electron capture detector for pesticide residues. A total of 220 samples of fruits were extracted and analyzed for pesticide residues, mainly organochlorines (γ-HCH, δ-HCH, aldrin, heptachlor, γ-chlordane, heptachlor epoxide, α-endosulfan, p,p'-DDE, endrin, β-endosulfan, o,p'-DDT, endrin aldehyde, p,p'- DDT, endrin ketone and methoxychlor). The data showed that most of the fruit samples analyzed contain residues of the monitored pesticides above the accepted maximum residue limit (MRL) as adopted by the FAO/WHO Codex Alimentarius Commission (CAC). The results obtained showed that 38.6 % fruit samples showed results above the MRL, 48.7 % were below the MRL and 12.7 % contained no detectable level of the monitored pesticides. Data analysis of health risk estimates indicated that, particularly γ-HCH, δ-HCH, o,p'-DDT, p,p'-DDE or p,p'-DDT do not pose a direct hazard to human health, although present in the three fruits (pawpaw, tomato and apple). However, heptachlor, heptachlor epoxide, endrin aldehyde, and endrin ketone levels exceeded the reference dose, indicating a great potential for systemic toxicity, especially in children who are considered to be the most vulnerable population subgroup. Lastly, the public is aware of pesticide residues in fruits and advocates for the curtailing of pesticide use on horticulture produce or strong educational programmes for farmers on control and safer use of pesticides. (au)

  16. CO2 storage in depleted gas reservoirs: A study on the effect of residual gas saturation

    Directory of Open Access Journals (Sweden)

    Arshad Raza

    2018-03-01

    Full Text Available Depleted gas reservoirs are recognized as the most promising candidate for carbon dioxide storage. Primary gas production followed by injection of carbon dioxide after depletion is the strategy adopted for secondary gas recovery and storage practices. This strategy, however, depends on the injection strategy, reservoir characteristics and operational parameters. There have been many studies to-date discussing critical factors influencing the storage performance in depleted gas reservoirs while little attention was given to the effect of residual gas. In this paper, an attempt was made to highlight the importance of residual gas on the capacity, injectivity, reservoir pressurization, and trapping mechanisms of storage sites through the use of numerical simulation. The results obtained indicated that the storage performance is proportionally linked to the amount of residual gas in the medium and reservoirs with low residual fluids are a better choice for storage purposes. Therefore, it would be wise to perform the secondary recovery before storage in order to have the least amount of residual gas in the medium. Although the results of this study are useful to screen depleted gas reservoirs for the storage purpose, more studies are required to confirm the finding presented in this paper.

  17. Fuel gas production from animal residue. Dynatech report No. 1551

    Energy Technology Data Exchange (ETDEWEB)

    Ashare, E.; Wise, D.L.; Wentworth, R.L.

    1977-01-14

    A comprehensive mathematical model description of anaerobic digestion of animal residues was developed, taking into account material and energy balances, kinetics, and economics of the process. The model has the flexibility to be applicable to residues from any size or type of animal husbandry operation. A computer program was written for this model and includes a routine for optimization to minimum unit gas cost, with the optimization variables being digester temperature, retention time, and influent volatile solids concentration. The computer program was used to determine the optimum base-line process conditions and economics for fuel gas production via anaerobic digestion of residues from a 10,000 head environmental beef feedlot. This feedlot at the conditions for minimum unit gas cost will produce 300 MCF/day of methane at a cost of $5.17/MCF (CH/sub 4/), with a total capital requirement of $1,165,000, a total capital investment of $694,000, and an annual average net operating cost of $370,000. The major contributions to this unit gas cost are due to labor (37 percent), raw manure (11 percent), power for gas compression (10 percent), and digester cost (13 percent). A conceptual design of an anaerobic digestion process for the baseline conditions is presented. A sensitivity analysis of the unit gas cost to changes in the major contributions to unit gas cost was performed, and the results of this analysis indicate areas in the anaerobic digestion system design where reasonable improvements could be expected so as to produce gas at an economically feasible cost. This sensitivity analysis includes the effects on unit gas cost of feedlot size and type, digester type, digester operating conditions, and economic input data.

  18. Fuel gas production from animal and agricultural residues and biomass

    Energy Technology Data Exchange (ETDEWEB)

    Wise, D. L; Wentworth, R. L

    1978-05-30

    Progress was reported by all contractors. Topics presented include: solid waste to methane gas; pipeline fuel gas from an environmental cattle feed lot; heat treatment of organics for increasing anaerobic biodegradability; promoting faster anaerobic digestion; permselective membrane control of algae and wood digesters for increased production and chemicals recovery; anaerobic fermentation of agricultural residues; pilot plant demonstration of an anaerobic, fixed-film bioreactor for wastewater treatment; enhancement of methane production in the anaerobic diegestion of sewage; evaluation of agitation concepts for biogasification of sewage sludge; operation of a 50,000 gallon anaerobic digester; biological conversion of biomass to methane; dirt feedlot residue experiments; anaerobic fermentation of livestock and crop residues; current research on methanogenesis in Europe; and summary of EPA programs in digestion technology. (DC)

  19. Graphic Three-Axes Presentation of Residual Gas Analyzer Data

    Science.gov (United States)

    Johnson, Kenneth R.; Levi, Alejandro G.

    1997-01-01

    Residual gas analyzers (RGA) are commonly used to measure the composition of residual gases in thermal-vacuum test chambers. Measurements from RGA's are often used to identify and quantify outgassing contaminants from a test article during thermal-vacuum testing. RGA data is typically displayed as snapshots in time, showing instantaneous concentrations of ions from ionized residual gas molecules at different atomic masses. This ion concentration information can be interpreted to be representative of the composition of the residual gas in the chamber at the instant of analysis. Typically, test personnel are most interested in tracking the time history of changes in the composition of chamber residual gas to determine the relative cleanliness and the clean-up rate of the test article under vacuum. However, displays of instantaneous RGA data cannot provide test personnel with the preferred time history information. In order to gain an understanding of gas composition trends, a series of plots of individual data snapshots must be analyzed. This analysis is cumbersome and still does not provide a very satisfactory view of residual gas composition trends. A method was devised by the authors to present RCA data in a three-axis format, plotting Atomic Mass Unit (AMU), the Ionization Signal Response (ISR) as amps/torr as a function of AMU, and Time, to provide a clear graphic visualization of trends of changes in ISR with respect to time and AMU (representative of residual gas composition). This graphic visualization method provides a valuable analytical tool to interpret test article outgassing rates during thermal vacuum tests. Raw RGA data was extracted from a series of delimited ASCII files and then converted to a data array in a spreadsheet. Consequently, using the 3-D plotting functionality provided by the spreadsheet program, 3-D plots were produced. After devising the data format conversion process, the authors began developing a program to provide real-time 3-D

  20. Minimizing Residual Pressure within a Windowless Gas Target System - JENSA

    Science.gov (United States)

    Gomez, Orlando; Browne, Justin; Kontos, Antonios; Montes, Fernando; Jensa Collaboration

    2015-04-01

    Nuclear reactions between light gases and radioactive isotope beams are essential to address open questions in nuclear structure and astrophysics. Pure light gas targets are critical for the measurements of proton- and alpha-induced reactions. J _ et E _ xperiments in N _ uclear S _ tructure and A _ strophysics (JENSA) is the world's most dense (~ 1019 atoms/cm2) windowless gas target system. Most of the gas flow is localized; however, escaping gas creates a pressure gradient which degrades experimental measurements and contaminates the beam line. JENSA contains a differential pumping system to maintain a vacuum. The previous design configuration was not optimized for experiments (pressure measurements 70 cm downstream from the jet were ~ 10-3 torr; optimal is less than 10-4 torr). We have altered the current differential pumping system to minimize the residual pressure profile. Several configurations of two gas-receiving catchers were tested, and the most efficient ones identified using Enhanced Pirani and Cold Cathode gauges. We have determined the 30 mm outer and 20 mm inner gas-receiving cones minimize JENSA central chamber pressure to 200 millitorr at 16,000 torr of discharge pressure. Altering the tubing configuration has additionally lowered the pressure 70 cm downstream to 10-5 torr. The new residual pressure allows operation of JENSA with planned expansion of a recoil mass separator SECAR.

  1. Residual Gas Fluorescence for Profile Measurements at the GSI UNILAC

    CERN Document Server

    Forck, P

    2002-01-01

    The high beam currents, delivered at the LINAC at GSI (UNILAC) can destroy intercepting diagnostics within one macro-pulse. As an alternative for a non-destructive profile measurement the methode for residual-gas-fluorescence is investigated. The fluorescence light is emitted by the N2 molecules of the residual gas at the blue wavelength range and can be monitored with a modern CCD-camera. The images are transferred via digital bus (IEEE 1394 'FireWire') and the profiles are generated by analysis of the images with a modern software tool (National Instruments 'LabView'). Due to the short beam pulses (about 0.2 ms) the light intensities emitted by the residual gas are low and require a high amplification (gain >106) which is realized with an image intensifier with double MCP (multi channel plate), connected with a fiber taper to the CCD-chip. The design parameters of the optics and electronics are discussed as well as the advantages of the digital data transmission. Measurements with heavy ion beams of several...

  2. Residual stresses evaluation in a gas-pipeline crossing

    Energy Technology Data Exchange (ETDEWEB)

    Fonseca, Maria Cindra [Universidade Federal Fluminense (UFF), Niteroi, RJ (Brazil); Almeida, Manoel Messias [COMPAGAS, Curitiba, PR (Brazil); Rebello, Joao Marcos Alcoforado [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil); Souza Filho, Byron Goncalves de [PETROBRAS, Rio de Janeiro, RJ (Brazil)

    2009-07-01

    The X-rays diffraction technique is a well established and effectiveness method in the determination of the residual and applied stresses in fine grained crystalline materials. It allows to characterize and to quantify the magnitude and direction of the existing surface stresses in the studied point of the material. The objective of this work is the evaluation of the surface stresses in a 10 in diameter Natural Gas Distribution Pipeline manufactured from API 5 L Gr B steel of COMPAGAS company, in a crossing with a Natural Gas Transportation Pipeline, in Araucaria-PR. This kind of evaluation is important to establish weather you have to perform a repositioning of one of the pipeline or not. The measurements had been made in two transversal sections of the pipe, the one upstream (170 mm of the external wall of the pipeline) and another one downstream (840 mm of the external wall of the pipeline). Each transversal section measurements where carried out in 3 points: 9 hours, 12 hours and 3 hours. In each measured point of the pipe surface, the longitudinal and transversal stresses had been measured. The magnitude of the surface residual stresses in the pipe varied of +180 MPa at the -210 MPa. The residual stress state on the surface of the points 12 hours region is characterized by tensile stresses and by compressive stresses in the points of 3 and 9 hours region. The surface residual stresses in gas-pipeline have been measured using X-ray diffraction method, by double exposure technique, using a portable apparatus, with Cr-K-alpha radiation. (author)

  3. Determination of gas residues in uranium dioxide pellets

    International Nuclear Information System (INIS)

    Riella, H.G.

    1978-01-01

    The measurement of low amounts of residual gases, excluding water, in ceramic grade uranium dioxide pellets, using high temperature vacuum extraction technique, is dealt with. The high temperature extraction gas analysis apparatus was designed and assembled for sequential analysis of up to eight uranium dioxide pellets by run. The system consists of three major units, namely outgassing unit, transfer unit and analytical unit. The whole system is evacuated to a final pressure of less then 10 -5 torr. A weighed pellet is transfered into the outgassing unit for subsequent dropping into a Platinum-Rhodium crucible which is heated inductively up to 1600 0 C during 30 minutes. The released gases are imediately transfered from the outgassing to analytical unit passing through a cold trap at -95 0 C to remove water vapor. The gases are transfered to previously calibrated volumetric bulb where the total pressure and temperature are determined. An estimate of the gas content in the pellets at STP condition is obtained from the measured volume, pressure and temperature of the gas mixture by applying ideal gases equation. Analysis to two lots (fourteen samples) of uranium dioxide pellets by the method described here indicated a mean gas content of 0,060cm 3 /g UO 2 . The lower limit of this technique is 0,03cm 3 /g UO 2 (STP). The time required for the analysis of eight pellets is about 9 hours [pt

  4. Comparison of thin layer chromatographic and gas chromatographic determination of propoxur residues in a cocoa ecosystem

    International Nuclear Information System (INIS)

    Yeboah, P.O.; Lowor, S.; Akpabli, C.K.

    2005-01-01

    The fate of propoxur in a cocoa ecosystem has been studied using thin layer chromatographic (TLC) and gas chromatographic (GC) methods. Residues of propoxur as determined by both TLC and GC were not significantly different. TLC analysis of propoxur residues in soil, cocoa leaves and pods did not require any rigorous cleanup since residues measured from cleaned extracts and without cleanup were not significantly different. The residue levels of propoxur in the soil were found to decrease rapidly and, by the 21st day, none was detected in the topsoil (0-15 cm). Evidence of leaching of propoxur residues in the soil has also been demonstrated. The amount left in the top soil after the first seven days were 27%, 23% and 24% of the initial one as determined by the TLC without cleanup, TLC with cleanup and GLC, respectively. No propoxur residue was detected in topsoil 21 days after spraying. About 38% of pesticides detected on the cocoa pod on the day of treatment remained on the pod seven days after treatment. The residue detected on the leaves on the day of treatment was higher than that in or on the soil. This decreased rapidly to 1.7% in 21 days compared to 16% for the soil and 23% for the pod. (author)

  5. Study of Residual Gas Analyser (RGA) Response towards Known Leaks

    International Nuclear Information System (INIS)

    Pathan, Firozkhan S; Khan, Ziauddin; Semwal, Pratibha; George, Siju; Raval, Dilip C; Thankey, Prashant L; Manthena, Himabindu; Yuvakiran, Paravastu; Dhanani, Kalpesh R

    2012-01-01

    Helium leak testing is the most versatile form of weld qualification test for any vacuum application. Almost every ultra-high vacuum (UHV) system utilizes this technique for insuring leak tightness for the weld joints as well as demountable joints. During UHV system under operational condition with many other integrated components, in-situ developed leaks identification becomes one of the prime aspect for maintaining the health of such system and for continuing the experiments onwards. Since online utilization of leak detector (LD) has many practical limitations, residual gas analyser (RGA) can be used as a potential instrument for online leak detection. For this purpose, a co-relation for a given leak rate between Leak Detector and RGA is experimentally established. This paper describes the experimental aspect and the relationship between leak detector and RGA.

  6. RESIDUAL-GAS-IONIZATION BEAM PROFILE MONITORS IN RHIC.

    Energy Technology Data Exchange (ETDEWEB)

    CONNOLLY, R.; MICHNOFF, R.; TEPIKIAN, S.

    2005-05-16

    Four ionization profile monitors (IPMs) in RHIC measure vertical and horizontal beam profiles in the two rings by measuring the distribution of electrons produced by beam ionization of residual gas. During the last three years both the collection accuracy and signal/noise ratio have been improved. An electron source is mounted across the beam pipe from the collector to monitor microchannel plate (MCP) aging and the signal electrons are gated to reduce MCP aging and to allow charge replenishment between single-turn measurements. Software changes permit simultaneous measurements of any number of individual bunches in the ring. This has been used to measure emittance growth rates on six bunches of varying intensities in a single store. Also the software supports FFT analysis of turn-by-turn profiles of a single bunch at injection to detect dipole and quadrupole oscillations.

  7. The emission of fluorine gas during incineration of fluoroborate residue

    Energy Technology Data Exchange (ETDEWEB)

    Feng, Yuheng, E-mail: fengyh@tongji.edu.cn [Thermal & Environmental Engineering Institute, Tongji University, Shanghai 200092 (China); Jiang, Xuguang [State Key Laboratory of Clean Energy Utilization, Zhejiang University, Hangzhou 310027 (China); Chen, Dezhen [Thermal & Environmental Engineering Institute, Tongji University, Shanghai 200092 (China)

    2016-05-05

    Highlights: • Gaseous fluorine products were identified when combusting fluoroborate residue. • BF{sub 3} and SiF{sub 4} tend to be hydrolyzed into HF with the increase of temperature. • The emission of BF{sub 3} and SiF{sub 4} from the chamber could be negligible at 1100 °C. - Abstract: The emission behaviors of wastes from fluorine chemical industry during incineration have raised concerns because multiple fluorine products might danger human health. In this study, fluorine emission from a two-stage incineration system during the combustion of fluoroborate residue was examined. In a TG-FTIR analysis BF{sub 3}, SiF{sub 4} and HF were identified as the initial fluorine forms to be released, while fluorine gases of greenhouse effect such as CF{sub 4} and SF{sub 6} were not found. Below 700 °C, NaBF{sub 4} in the sample decomposed to generate BF{sub 3}. Then part of BF{sub 3} reacted with SiO{sub 2} in the system to form SiF{sub 4} or hydrolyzed to HF. At higher temperatures, the NaF left in the sample was gradually hydrolyzed to form HF. A lab-scale two-stage tube furnace is established to simulate the typical two-stage combustion chamber in China. Experimental tests proved that HF was the only fluorine gas in the flue gas, and emissions of BF{sub 3} and SiF{sub 4} can be negligible. Thermodynamic equilibrium model predicted that all SiF{sub 4} would be hydrolyzed at 1100 °C in the secondary-chamber, which agreed well with the experimental results.

  8. Levels and distribution of pesticide residues in soil and sediments in ...

    African Journals Online (AJOL)

    The aim of this study was to investigate the types, levels and distribution of pesticide residues in Eastern Lake Tanganyika basin in Tanzania. Water, soil and sediments samples were collected from various sites in Kigoma region. Analyses of cleaned sample extracts were performed using gas chromatographyelectron ...

  9. Assessment of pesticide residues in some fruits using gas chromatography coupled with micro electron capture detector

    International Nuclear Information System (INIS)

    Latif, Y.; Sherazi, S.T.H.; Bhanger, M.I.

    2011-01-01

    A very sensitive analytical method for the determination of 26 pesticides in some fruits based on solid phase extraction (SPE) cleanup was developed using gas chromatography (GC) coupled with micro electron capture detector (mu ECD). The identity of the pesticides was confirmed by gas chromatography mass spectroscopy (GC-MS) using selected ion monitoring (SIM) mode. Ethyl acetate was used as a solvent for the extraction of pesticide residues with assistance of sonication. For cleanup an octadecyl, C18 SPE column was used. A linear response of mu ECD was observed for all pesticides with good correlation coefficients (>0.9992). Proposed method was successfully applied for the determination of pesticide residues in the orange, apple, and grape fruits. Average recoveries achieved for all of the pesticides at fortification levels of 0.05, 1.0 and 2.0 mu g g/sup -1/ in analyzed fruits were above 90% with relative standard deviations (RSD) less than 6%. (author)

  10. Tokamak residual zonal flow level in near-separatrix region

    International Nuclear Information System (INIS)

    Bing-Ren, Shi

    2010-01-01

    Residual zonal flow level is calculated for tokamak plasmas in the near-separatrix region of a diverted tokamak. A recently developed method is used to construct an analytic divertor tokamak configuration. It is shown that the residual zonal flow level becomes smaller but still keeps finite near the separatrix because the neoclassical polarisation mostly due to the trapped particles goes larger in this region. (fluids, plasmas and electric discharges)

  11. Effects of storage and processing on residue levels of chlorpyrifos in soybeans.

    Science.gov (United States)

    Zhao, Liuwei; Ge, Jing; Liu, Fengmao; Jiang, Naiwen

    2014-05-01

    The residue levels of chlorpyrifos in soybeans during storage and processing were investigated. Soybeans were treated with chlorpyrifos aqueous solution and placed in a sealed plastic container. The residue of chlorpyrifos was determined in soybeans at six time points within 0 and 112days during storage and oil processing of the soybeans was conducted. The analysis of the residues of chlorpyrifos was carried out by gas chromatography-mass spectrometry (GC-MS). Results show that the dissipation of chlorpyrifos in soybeans is about 62% during the storage period. Moreover, the carryover of the residues from soybeans into oil is found to be related to the processing methods. Processing factor, which is defined as the ratio of chlorpyrifos residue concentration in oil sample to that in the soybean samples, was 11 and 0.25 after cold and hot pressing, respectively. Copyright © 2013 Elsevier Ltd. All rights reserved.

  12. Residual Gas and Dust around Transition Objects and Weak T Tauri Stars

    Energy Technology Data Exchange (ETDEWEB)

    Doppmann, Greg W. [W. M. Keck Observatory, 65-1120 Mamalahoa Hwy., Kamuela, HI 96743 (United States); Najita, Joan R. [National Optical Astronomy Observatory, 950 N. Cherry Avenue, Tucson, AZ 85719 (United States); Carr, John S., E-mail: gdoppmann@keck.hawaii.edu, E-mail: najita@noao.edu, E-mail: carr@nrl.navy.mil [Naval Research Laboratory, Code 7213, Washington, DC 20375 (United States)

    2017-02-20

    Residual gas in disks around young stars can spin down stars, circularize the orbits of terrestrial planets, and whisk away the dusty debris that is expected to serve as a signpost of terrestrial planet formation. We have carried out a sensitive search for residual gas and dust in the terrestrial planet region surrounding young stars ranging in age from a few to ∼10 Myr. Using high-resolution 4.7 μ m spectra of transition objects (TOs) and weak T Tauri stars, we searched for weak continuum excesses and CO fundamental emission, after making a careful correction for the stellar contribution to the observed spectrum. We find that the CO emission from TOs is weaker and located farther from the star than CO emission from nontransition T Tauri stars with similar stellar accretion rates. The difference is possibly the result of chemical and/or dynamical effects (i.e., a low CO abundance or close-in low-mass planets). The weak T Tauri stars show no CO fundamental emission down to low flux levels (5 × 10{sup −20} to 10{sup −18} W m{sup −2}). We illustrate how our results can be used to constrain the residual disk gas content in these systems and discuss their potential implications for star and planet formation.

  13. Chloroxyanion residues in cantaloupe and tomatoes after chlorine dioxide gas sanitation

    Science.gov (United States)

    Chlorine dioxide gas is effective at cleansing fruits and vegetables of bacterial pathogens and(or) rot organisms, but few data are available on chemical residues remaining subsequent to chlorine gas treatment. Therefore, studies were conducted to quantify chlorate and perchlorate residues after tom...

  14. [Simultaneous determination of seven residual solvents in bovis calculus artifactus by headspace gas chromatography].

    Science.gov (United States)

    Chi, Shuyao; Wu, Dike; Sun, Jinhong; Ye, Ruhan; Wang, Xiaoyan

    2014-05-01

    A headspace gas chromatography (HS-GC) method was developed for the simultaneous determination of seven residual solvents (petroleum ether (60-90 degrees C), acetone, ethyl acetate, methanol, methylene chloride, ethanol and butyl acetate) in bovis calculus artifactus. The DB-WAX capillary column and flame ionization detector (FID) were used for the separation and detection of the residual solvents, and the internal standard method was used for the quantification. The chromatographic conditions, such as equilibrium temperature and equilibrium time, were optimized. Under the optimized conditions, all of the seven residual solvents showed good linear relationships with good correlation coefficients (not less than 0.999 3) in the prescribed concentration range. At three spiked levels, the recoveries for the seven residual solvents were 94.7%-105.2% with the relative standard deviations (RSDs) less than 3.5%. The limits of detection (LODs) of the method were 0.43-5.23 mg/L, and the limits of quantification (LOQs) were 1.25-16.67 mg/L. The method is simple, rapid, sensitive and accurate, and is suitable for the simultaneous determination of the seven residual solvents in bovis calculus artifactus.

  15. Residue levels and dissipation behaviors for trifloxystrobin and tebuconazole in mango fruit and soil.

    Science.gov (United States)

    Mohapatra, Soudamini

    2015-03-01

    An evaluation of residue levels of trifloxystrobin and tebuconazole was carried out on mango fruits after treatments with the combined formulation, trifloxystrobin (25 % w/w) and tebuconazole (50 % w/w), at standard and double doses of 250 + 500 and 500 + 1000 g a.i. ha(-1), respectively. Extraction and purification of the mango fruit samples were carried out by the QuEChERS method after validating the analytical parameters. Determination of the fungicides was carried out by gas chromatography (GC) and gas chromatography-mass spectrometry (GC-MS). The limits of detection (LOD) and limits of quantification (LOQ) for both fungicides were 0.015 μg mL(-1) and 0.05 mg kg(-1), respectively. The residue levels of trifloxystrobin for standard and double-dose treatments were 0.492 and 0.901 mg kg(-1) and for tebuconazole were 0.535 and 1.124 mg kg(-1), respectively. A faster dissipation of tebuconazole in mango fruit was observed compared with that for tebuconazole. Dissipation of trifloxystrobin and tebuconazole in mango followed first-order kinetics, and the half-lives were 9 and 6 days, respectively. The preharvest intervals (PHI), the time taken for the combined residues of trifloxystrobin and tebuconazole to dissipate to their permissible levels (maximum residue limits), were 14 and 20 days for standard and double doses, respectively. At harvest, mature mango fruit and soil were free from fungicide residues.

  16. Injection, flow, and mixing of CO2 in porous media with residual gas.

    Energy Technology Data Exchange (ETDEWEB)

    Oldenburg, C.M.; Doughty, C.A.

    2010-09-01

    Geologic structures associated with depleted natural gas reservoirs are desirable targets for geologic carbon sequestration (GCS) as evidenced by numerous pilot and industrial-scale GCS projects in these environments world-wide. One feature of these GCS targets that may affect injection is the presence of residual CH{sub 4}. It is well known that CH{sub 4} drastically alters supercritical CO{sub 2} density and viscosity. Furthermore, residual gas of any kind affects the relative permeability of the liquid and gas phases, with relative permeability of the gas phase strongly dependent on the time-history of imbibition or drainage, i.e., dependent on hysteretic relative permeability. In this study, the effects of residual CH{sub 4} on supercritical CO{sub 2} injection were investigated by numerical simulation in an idealized one-dimensional system under three scenarios: (1) with no residual gas; (2) with residual supercritical CO{sub 2}; and (3) with residual CH{sub 4}. We further compare results of simulations that use non-hysteretic and hysteretic relative permeability functions. The primary effect of residual gas is to decrease injectivity by decreasing liquid-phase relative permeability. Secondary effects arise from injected gas effectively incorporating residual gas and thereby extending the mobile gas plume relative to cases with no residual gas. Third-order effects arise from gas mixing and associated compositional effects on density that effectively create a larger plume per unit mass. Non-hysteretic models of relative permeability can be used to approximate some parts of the behavior of the system, but fully hysteretic formulations are needed to accurately model the entire system.

  17. Origins of the residual pulse height deficit in propane-filled gas ionization detectors

    International Nuclear Information System (INIS)

    Weijers-Dall, T.D.M.; Timmers, H.; Elliman, R.G.

    2005-01-01

    This work investigates the origins of the residual pulse height deficit in gas ionization detectors. It is motivated by the recent observation that the species dependence of gas detector response cannot be accounted for solely by considering the energy loss of the ions in the detector window and non-ionizing energy loss processes in the detector gas. It was found that the residual pulse height deficit is approximately proportional to the square of the ionization density. However, only a weak dependence of the residual deficit on gas pressure (in the range 70-120mbar) was observed. It is hypothesized that the residual pulse height deficit in gas ionization detectors results from the effect of multiple ionization of individual gas molecules at high ionization densities on the energy required to create an electron-ion pair

  18. Determination of dichlorvos residue levels in vegetables sold in ...

    African Journals Online (AJOL)

    To ensure maximum yield they apply various types of pesticides to control pests and diseases that attack these vegetables. Organophosphate pesticides are widely used in agriculture for the control of various insect pests mainly in developing countries. The purpose of the study was to determine the residual levels of the ...

  19. Study of residual gas adsorption on GaN nanowire arrays photocathode

    Energy Technology Data Exchange (ETDEWEB)

    Xia, Sihao; Liu, Lei, E-mail: liu1133_cn@sina.com.cn; Diao, Yu; Kong, Yike

    2017-05-01

    Highlights: • H{sub 2}O is more easily to absorb on the nanowire surface. • The work function increase after residual gas adsorption. • Bandgaps of the nanowire increase slightly. • Absorption coefficient is reduced and moves to higher energy side. - Abstract: In order to find out the influences of residual gas on GaN nanowire arrays photocathode, the optoelectronic properties of adsorption system are calculated on the basis of first principles. Results suggest that the residual gas adsorption will increase the work function and introduce a dipole moment with a direction from the nanowire to the adsorbates. The surface structures are changed and electrons transfer from nanowire to gas molecule. The bandgaps are enhanced after adsorption. Besides, the peak of absorption coefficients is reduced and moves to higher energy side. It is discovered that residual gas will drastically degrade the characteristics and lifetime of GaN nanowire arrays photocathode.

  20. Gas chromatographic determination of pesticide residues in white mustard.

    Science.gov (United States)

    Słowik-Borowiec, Magdalena; Szpyrka, Ewa; Walorczyk, Stanisław

    2015-04-15

    A new analytical method employing gas chromatography coupled to electron capture and nitrogen phosphorus detection (GC-ECD/NPD) has been developed and validated for the screening and quantification of 51 pesticides in a matrix of high chlorophyll content - white mustard (Sinapis alba L.). For preparation of the sample extract, the citrate buffered QuEChERS procedure was followed. However certain changes were made to adapt the method to our needs and available laboratory resources. The sample size was reduced to 5 g, 10 mL water was added and exchange of solvent before GC analysis was done. The samples spiked with the target pesticides at the concentration level 0.01 mg/kg and a higher level (depending on the compound) yielded average recoveries in the range of 70-120% with relative standard deviations (RSDs) 0-19% except for HCB, S-metolachlor and teflubenzuron, and displayed very good linearity (R(2)>0.99) for nearly all the analytes. Limit of quantification was 0.01 mg/kg for the majority of the analytes. The expanded measurement uncertainties were estimated employing a "top-down" empirical model as being between 6% and 32% and yielding an average value of 18% (coverage factor k=2, confidence level 95%). Copyright © 2014 Elsevier Ltd. All rights reserved.

  1. Microstructural damage and residual mechanical properties in helium-bearing gas metal Arc weldments

    Science.gov (United States)

    Goods, S. H.; Yang, N. Y. C.

    1992-03-01

    The influence of entrapped helium on microstructural damage and residual mechanical properties subsequent to applying low-penetration gas metal arc (GMA) weld overlays was examined for an AISI Type 304 stainless steel. Two helium levels were examined: 22.5 and 85.0 atomic parts per million (appm) He. Detailed scanning electron microscopy (SEM) revealed the presence of intergranular cracks in the weld heat-affected zone (HAZ). The crack surfaces exhibited a dimple structure that was characteristic of a gas bubble embrittled material. Transmission electron microscopy (TEM) revealed that the size and spacing of the grain boundary helium gas bubbles remained virtually unchanged (relative to that established by the charging and aging procedure) at distances greater than 1 mm from the fusion line. Within this first millimeter, the diameter of the bubbles increased rapidly, and the bubble spacing increased to the characteristic spacing of the dimples that decorated weld-induced cracks. Mechanical testing revealed a loss in strain-to-fracture and ultimate tensile strength (UTS) at the higher helium level. While the majority of the fracture occurred in a transgranular, ductile manner, some deformation-induced intergranular cracking was observed. This cracking occurred over a very narrow region localized to the HAZ of the weldment. At the lower helium level, ductility and strength were unaffected compared to helium-free specimens.

  2. Assessment of Pesticide Residues in Some Fruits Using Gas Chromatography Coupled with Micro Electron Capture Detector

    Directory of Open Access Journals (Sweden)

    M. I. Bhanger

    2011-12-01

    Full Text Available A very sensitive analytical method for the determination of 26 pesticides in some fruits based on solid phase extraction (SPE cleanup was developed using gas chromatography (GC coupled with micro electron capture detector (μECD. The identity of the pesticides was confirmed by gas chromatography mass spectroscopy (GC-MS using selected ion monitoring (SIM mode. Ethyl acetate was used as a solvent for the extraction of pesticide residues with assistance of sonication. For cleanup an octadecyl, C18 SPE column was used. A linear response of μECD was observed for all pesticides with good correlation coefficients (>0.9992. Proposed method was successfully applied for the determination of pesticide residues in the orange, apple, and grape fruits. Average recoveries achieved for all of the pesticides at fortification levels of 0.05, 1.0 and 2.0 μg g-1 in analyzed fruits were above 90% with relative standard deviations (RSD less than 6

  3. Chloroxyanion Residues in Cantaloupe and Tomatoes after Chlorine Dioxide Gas Sanitation.

    Science.gov (United States)

    Smith, D J; Ernst, W; Herges, G R

    2015-11-04

    Chlorine dioxide gas is effective at cleansing fruits and vegetables of bacterial pathogens and(or) rot organisms, but little data are available on chemical residues remaining subsequent to chlorine gas treatment. Therefore, studies were conducted to quantify chlorate and perchlorate residues after tomato and cantaloupe treatment with chlorine dioxide gas. Treatments delivered 50 mg of chlorine dioxide gas per kg of tomato (2-h treatment) and 100 mg of gas per kg of cantaloupe (6-h treatment) in sealed, darkened containers. Chlorate residues in tomato and cantaloupe edible flesh homogenates were less than the LC-MS/MS limit of quantitation (60 and 30 ng/g respectively), but were 1319 ± 247 ng/g in rind + edible flesh of cantaloupe. Perchlorate residues in all fractions of chlorine dioxide-treated tomatoes and cantaloupe were not different (P > 0.05) than perchlorate residues in similar fractions of untreated tomatoes and cantaloupe. Data from this study suggest that chlorine dioxide sanitation of edible vegetables and melons can be conducted without the formation of unwanted residues in edible fractions.

  4. Determination of organophosphorus pesticide residues in tomatoes by gas chromatography

    International Nuclear Information System (INIS)

    Souissi, Sihem

    2010-01-01

    Chloropyriphos and malathion are two organophosphorus pesticides from many others pesticides widely used by famers in agriculture .Because of their bad effect on human health, officials standards are set by the international organisations and communities to ensure safer food for consumer .In the same way, scientists over the world are working hard to develop new detection techniques responding to the international requirements. In this study, an ' IAEA-ethylacetate method ', an adaptation of the popular QuEChERS multi residue method, was optimized to analyse chloropyriphos and Malathion residues in tomatoes .Ethyl-Acetate was used as an extraction solvent the PSA was kept for the clean up procedure. GC-NPD is used for samples analysis .The method optimized is specifique, selective with a recovery averaged more than 70 pour cent. A complete validation of the method is necessary to be used for routine analysis.

  5. Residual lifetime assessment of uPVC gas pipes

    OpenAIRE

    Visser, HA

    2010-01-01

    The Dutch gas distribution network consists of about 20% (22,500 km) of unplasticised poly(vinyl chloride) (uPVC) pipes, most of which have been installed from the mid-sixties up to the mid-seventies of the previous century and have been in service ever since. Replacing the uPVC gas pipes exactly after the specified service lifetime of 50 years will lead to a costly and extremely labour intensive project in the next decade. Postponing the replacement is only an option when it can be done with...

  6. Characteristics of gas and residues produced from electric arc pyrolysis of waste lubricating oil.

    Science.gov (United States)

    Song, Geum-Ju; Seo, Yong-Chil; Pudasainee, Deepak; Kim, In-Tae

    2010-07-01

    An attempt has been made to recover high-calorific fuel gas and useful carbonaceous residue by the electric arc pyrolysis of waste lubricating oil. The characteristics of gas and residues produced from electric arc pyrolysis of waste lubricating oil were investigated in this study. The produced gas was mainly composed of hydrogen (35-40%), acetylene (13-20%), ethylene (3-4%) and other hydrocarbons, whereas the concentration of CO was very low. Calorific values of gas ranged from 11,000 to 13,000 kcal kg(-1) and the concentrations of toxic gases, such as NO(x), HCl and HF, were below the regulatory emissions limit. Gas chromatography-mass spectrometry (GC/MS) analysis of liquid-phase residues showed that high molecular-weight hydrocarbons in waste lubricating oil were pyrolyzed into low molecular-weight hydrocarbons and hydrogen. Dehydrogenation was found to be the main pyrolysis mechanism due to the high reaction temperature induced by electric arc. The average particle size of soot as carbonaceous residue was about 10 microm. The carbon content and heavy metals in soot were above 60% and below 0.01 ppm, respectively. The utilization of soot as industrial material resources such as carbon black seems to be feasible after refining and grinding. Copyright (c) 2009 Elsevier Ltd. All rights reserved.

  7. Levels of organochlorine pesticide residue in grasscutter (Thryonomys swinderianus) tissues

    International Nuclear Information System (INIS)

    Blankson-Arthur, S.

    2009-06-01

    the kidney. The level of endrin ketone was higher than endrin aldehyde in all the tissues analyzed. The mean concentration of endrin ketone was 0.347 μg /kg in the kidney. The mean concentration of α-endosulfan was 0.140μg /kg wet weight. Endosulfan sulfate was detected at 0.033 μg /kg in the kidney. The mean concentration of gamma-chlordane was 0.020 μg /kg kidney. Methoxychlor was detected at 0.183μg /kg, wet weight in the kidney. The levels of organochlorine pesticides residues detected in all the tissues were below the accepted maximum residue limits (MRL), as adopted by the WHO/FAO Codex Alimentarius Commission.

  8. Validation of a methodology multi-residue for the determination of pesticides residuals in strawberry (fragraria spp.) by gas chromatography

    International Nuclear Information System (INIS)

    Montano Garces, Mauricio; Guerrero Dallos, Jairo Arturo

    2001-01-01

    This study describes the validation of multi-residue analytical methodology for the simultaneous determination of 19 organ chlorine, organophosphorus and organ nitrogen pesticides in strawberry. Pesticides residues were extracted from strawberry samples with ethyl acetate, the extracts were cleaned-up by GPC, the quantitative analysis was carried out by high resolution gas chromatography (GC) with a pulsed splitless injection mode and simultaneous detection by m-ECD and NPD coupled in parallel. The methodology is specific, selective, and accurate and robust the calibration curves in matrix matched analytical standards show linearity over the concentration range of 0.04-5.00 mg/kg with limits of detection and quantitation between 0.007-0.5 mg/kg and 0.01-1.00 mg/kg respectively. The recovery experiments yielding averages between 80-110% for most of the pesticides. The distribution of analyze in the laboratory sample was evaluated and it was found its homogeneity. The methodology was applied in field samples and was mainly found Captan residues below MRL

  9. Effect of flue gas desulfurization residue on plant establishment and soil and leachate quality

    Energy Technology Data Exchange (ETDEWEB)

    Punshon, T.; Adriano, D.C.; Weber, J.T. [University of Georgia, Savannah, GA (USA). Savannah River Ecology Lab.

    2001-06-01

    Effects on soil quality and crop establishment after incorporation of flue gas desulfurization by-product (FGD) into soil as an amendment was assessed in a mesocosm study. Mesocosm units received applications equivalent to 0, 2.5, 5.0, 7.5 and 10% FGD residue. Germination, biomass production, and elemental composition of corn, radish and cotton were determined. The quality of leachates and soil were also determined periodically. Flue gas desulfurization residue did not affect germination and all application rates stimulated aboveground biomass. Plants grown in FGD-amended soil contained significantly elevated tissue concentrations of As, B, Se, and Mo. The FGD residue elevated surface soil pH from 5.5 to 8.1. Leachate pH was unaffected by FGD, but salinity rose sharply with increasing application rates of FGD. Leachates contained higher concentrations of B, with small increases in Se and As. Flue gas desulfurization residue application caused an increase in total B, As, Mo, Se and extractable Ca in the soil, but decreased Mn and Zn. Using FGD residues could have beneficial effects on crop establishment without detrimental effects on soil or leachate quality, at an optimum rate of approximately 2.5%. This material could alleviate surface acidity, and B and Mo deficiencies in plants. 27 refs., 6 figs., 4 tabs.

  10. Analysis of residual swirl in tangentially-fired natural gas-boiler

    International Nuclear Information System (INIS)

    Hasril Hasini; Muhammad Azlan Muad; Mohd Zamri Yusoff; Norshah Hafeez Shuaib

    2010-01-01

    This paper describes the investigation on residual swirl flow in a 120 MW natural gas, full-scale, tangential-fired boiler. Emphasis is given towards the understanding of the behavior of the combustion gas flow pattern and temperature distribution as a result of the tangential firing system of the boiler. The analysis was carried out based on three-dimensional computational modeling on full scale boiler with validation from key design parameter as well as practical observation. Actual operating parameters of the actual boiler are taken as the boundary conditions for this modeling. The prediction of total heat flux was found to be in agreement with the key design parameter while the residual swirl predicted at the upper furnace agrees qualitatively with the practical observation. Based on this comparison, detail analysis was carried out for comprehensive understanding on the generation and destruction of the residual swirl behavior in boiler especially those with high capacity. (author)

  11. The Continuation Study of the Measurement of Residual Monomer from theDenture Base After Three Month Worn by Gas Chromatography on the Radiationand Non Radiation Worker

    International Nuclear Information System (INIS)

    Isyuniarto; Winoto

    2000-01-01

    Residual monomer measurement on the radiation and non radiation workerafter three month worn the denture has been done. The aim of the research isto investigated residual monomer concentration on after three month worn. Thedenture base material, made of resin acrylic, sometimes is cause mucosairritation in the mouth, and dental irritation or allergic reaction, becauseof residual monomer that left on the mouth cavity. In this research two groupwere needed there are the radiation and non radiation worker, the level ofthe residual monomer count by gas chromatography analysis. The result of thisresearch showed that the level of residual monomer of two group are same orthere have same level of the limit value. The measurement result is in therange of 0.1783 ± 0.011 mg/l to 0.1790 ± 0.004 mg/l. (author)

  12. Residue Levels and Risk Assessment of Pesticides in Pistachio Nuts in Iran

    Directory of Open Access Journals (Sweden)

    Azadeh Emami

    2017-02-01

    Full Text Available Background: Pistachio is one of the main nutrients, not only as a strategic crop but also as a main type of nut, in Iranians’ food cycle. The aim of this study was to measure the relative safety of Iranian pistachio based on the standard pesticide’s residue limits, which should be monitored and assessed in the cultivation of pistachio in order to confirm its public health. Methods: Fifty samples of pistachios of different brands were collected from Tehran markets in 2015. QuEChERS (Quick, Easy, Cheap, Effective, Rugged and Safe sampling method was used in order to determine the pesticide’s residue in the pistachio nuts by Gas chromatography/Mass spectrometry (GC/MS.The method was validated with related parameters. Recovery took place at five concentration rates (n=3 ranging from 81.40% to 93.08% with the majority of RelativeStandard Deviation being lower than 20%. Limits of detection and quantification for all the pesticides were 2µg/kg and10µg/kg, respectively. The validated method seemed to be appropriate for the analysis of pesticide’s residue in pistachio nuts. Results: Identified pesticides included Fenitrothion, Carbaryl and Diazinon. Detectable pesticide’s residue existed in 10% (5 samples of the samples. Conclusion: All the results were compared with the Iran’s National Standards and the European Maximum Residue Limits. As compared to the acceptable daily intake, the calculated daily intake of each pesticide was much lower than the standard level, which could not cause any public health problem.

  13. Controlling residual hydrogen gas in mass spectra during pulsed laser atom probe tomography.

    Science.gov (United States)

    Kolli, R Prakash

    2017-01-01

    Residual hydrogen (H 2 ) gas in the analysis chamber of an atom probe instrument limits the ability to measure H concentration in metals and alloys. Measuring H concentration would permit quantification of important physical phenomena, such as hydrogen embrittlement, corrosion, hydrogen trapping, and grain boundary segregation. Increased insight into the behavior of residual H 2 gas on the specimen tip surface in atom probe instruments could help reduce these limitations. The influence of user-selected experimental parameters on the field adsorption and desorption of residual H 2 gas on nominally pure copper (Cu) was studied during ultraviolet pulsed laser atom probe tomography. The results indicate that the total residual hydrogen concentration, H TOT , in the mass spectra exhibits a generally decreasing trend with increasing laser pulse energy and increasing laser pulse frequency. Second-order interaction effects are also important. The pulse energy has the greatest influence on the quantity H TOT , which is consistently less than 0.1 at.% at a value of 80 pJ.

  14. A method to determine residue levels of persistent organochlorine pesticides in human milk from Indonesian women.

    Science.gov (United States)

    Burke, Emma R; Holden, Alexis J; Shaw, Ian C

    2003-01-01

    A method has been developed for the analysis of organochlorine pesticides in human milk using solvent extraction, Florisil solid phase extraction clean-up and analysis by gas chromatography with an electron capture detector. The recovery of analytes from spiked milk samples was in the range 53 +/- 1% to 109 +/- 7% (n = 9). A small number of samples were obtained from women in a rural and an urban area of Indonesia and analysed using the developed method. The results are reported on a milk fat basis. All samples contained detectable residues of p,p'-DDT (urban mean 0.11 +/- 0.18 mgkg(-1) (n = 5), rural mean 0.07 +/- 0.03 mg kg(-1) (n = 5)) and p,p'-DDE (urban mean 0.05 +/- 0.04 m kg(-1) (n = 5), rural mean 0.76 +/- 1.46 mg kg(-1) (n = 5)). Residues of HCB, betaHCH, alpha-endosulfan and dieldrin were also detected in some samples. There was no significant difference (at the 95% confidence level) in levels of pesticides between urban and rural areas. The levels of organochlorine pesticides in milk from Indonesian women were lower than those reported from Indonesian women exposed to DDT through malaria eradication schemes and were similar to levels reported from UK and Japan.

  15. Determination of Profenofos Pesticidal Residue in Lettuce (Lactuca sativa L. by Gas Chromatographic Method

    Directory of Open Access Journals (Sweden)

    Yohannes Alen

    2015-05-01

    Full Text Available The determination of profenofos pesticidal residue in the lettuce (Lactuca sativa L. by using gas chromatography using flame photometric detector (FPD had been investigated. The lettuce was collected from Padang Luar area, Agam distric, West Sumatera. Sample for determination of profenofos residue divided into three groups: unwashed (A, washed with water (B, and washed with detergent (C. Maceration with sonication was used for the extraction using ethylacetateas a solvent. The results showed that profenofos pesticide residue in sample A, B and C were 0.204, 0.080 and 0.061 ppm, respectively. These profenofos pesticidal residue are over than the Maximum Residue Limits (MRL that established by The Japan Food Chemical Research Foundation (0.05 ppm even though World Health Organization (WHO has not established Maximum Residue Limits (MRL profenofos on lettuce. Based on the statistical analysis one-way method (Anova using SPSS 20.0 showed that there was a significant concentrations difference between lettuce A from lettuce B and lettuce C with p < 0.05.

  16. Monitoring volatilization products using Residual Gas Analyzers during MeV ion beam irradiations

    Science.gov (United States)

    Wetteland, C. J.; Kriewaldt, K.; Taylor, L. A.; McSween, H. Y.; Sickafus, K. E.

    2018-03-01

    The use of Residual Gas Analyzers (RGAs) during irradiation experiments can provide valuable information when incorporated into experimental end-stations. The instruments can track the volatilization products of beam-sensitive materials, which may ultimately aid researchers in selecting appropriate flux values for conducting experiments. Furthermore, the type of gaseous species released during an irradiation can be monitored directly, which may lead to new insights into the radiolysis and/or heating mechanisms responsible for gas evolution. A survey of several classes of materials exposed to extremes in particle flux is presented to show how RGA instrumentation can be incorporated to qualitatively assess ion-solid interactions in a variety of fields.

  17. Residual entropy and waterlike anomalies in the repulsive one dimensional lattice gas

    Energy Technology Data Exchange (ETDEWEB)

    Silva, Fernando Barbosa V. da [Instituto de Física, Universidade de Brasília, Brasília-DF (Brazil); Instituto Federal de Brasília, Campus São Sebastião, São Sebastião-DF (Brazil); Oliveira, Fernando Albuquerque, E-mail: fao@fis.unb.br [Instituto de Física, Universidade de Brasília, Brasília-DF (Brazil); Barbosa, Marco Aurélio A., E-mail: aureliobarbosa@gmail.com [Programa de Pós-Graduação em Ciência de Materiais, Faculdade UnB Planaltina, Universidade de Brasília, Planaltina-DF (Brazil)

    2015-04-14

    The thermodynamics and kinetics of the one dimensional lattice gas with repulsive interaction are investigated using transfer matrix technique and Monte Carlo simulations. This simple model is shown to exhibit waterlike anomalies in density, thermal expansion coefficient, and self-diffusion. An unified description for the thermodynamic anomalies in this model is achieved based on the ground state residual entropy which appears in the model due to mixing entropy in a ground state phase transition.

  18. Predicting the residual aluminum level in water treatment process

    OpenAIRE

    J. Tomperi; M. Pelo; K. Leiviskä

    2013-01-01

    In water treatment processes, aluminum salts are widely used as coagulation chemical. High dose of aluminum has been proved to be at least a minor health risk and some evidence points out that aluminum could increase the risk of Alzheimer's disease. Thus it is important to minimize the amount of residual aluminum in drinking water and water used at food industry. In this study, the data of a water treatment plant (WTP) was analyzed and the residual aluminum in drinking water was predicted usi...

  19. Predicting the residual aluminum level in water treatment process

    OpenAIRE

    J. Tomperi; M. Pelo; K. Leiviskä

    2012-01-01

    In water treatment processes, aluminum salts are widely used as coagulation chemical. High dose of aluminum has been proved to be at least a minor health risk and some evidence points out that aluminum could increase the risk of Alzheimer's disease thus it is important to minimize the amount of residual aluminum in drinking water and water used at food industry. In this study, the data of a water treatment plant (WTP) was analyzed and the residual aluminum in drinking water was predicted usin...

  20. Effect of Residual Gas Composition on Epitaxial Growth of Graphene on SiC

    Science.gov (United States)

    Kunc, J.; Rejhon, M.; Belas, E.; Dědič, V.; Moravec, P.; Franc, J.

    2017-10-01

    In recent years, graphene growth optimization has been one of the key routes towards large-scale, high-quality graphene production. We measure in situ residual gas content during epitaxial-graphene growth on silicon carbide (SiC) to find detrimental factors of epitaxial-graphene growth. The growth conditions in high vacuum, in argon, purified argon, and the flow of argon are compared. The grown epitaxial graphene is studied by Raman-scattering mapping. We determine mechanical strain, number of graphene layers and the graphene quality. The surface topography is measured by atomic force microscopy. Charge density and carrier mobility are studied by Hall-effect measurements in van der Pauw configuration. We identify the major role of the chemical reaction of carbon and residual water. The rate of the reaction is lowered when purified argon is used. We also show that, according to time-varying gas content, it is preferable to grow graphene at higher temperatures and shorter times. Other sources of growth environment contamination are also discussed. The reaction of residual gas and SiC is discussed as one of the factors decreasing the lateral size of SiC atomically flat terraces and leading to their irregular shape. The importance of purified argon and its sufficient flow rate is concluded to be important for high-quality graphene growth as it reduces the rate of undesired chemical reactions and provides a more stable and defined growth ambient.

  1. The difference of acrylic resin residual monomer levels with various polymerization method

    Directory of Open Access Journals (Sweden)

    Sherman Salim

    2011-12-01

    Full Text Available Background: After polymerization process, heat cured acrylic resin denture base actually still contains residual monomers that can become potential irritants later in oral cavity. Polymerization process is essential to obtain acrylic resin which can meet the requirements of the biocompatible and good physical properties. To meet the requirements, there are several methods of polymerization process used. Purpose: The purpose of this study was to determine the differences of the residual monomer levels of acrylic resin processed by various polymerization methods. Methods: Acrylic resin powder and liquid were mixed based on the rules of factory, and sample was made with size of 30 mm × 50 mm × 3 mm and then polymerized by using microwave at 70° C for 24 hours based on the methods of Japan Industrial Standard (JIS. Each group of samples was cut with weight of ± 0.2 g, dissolved in 5 ml of methyl ethyl ketone in test tubes, and then stored at ± 5° C for four days. Residual monomer level was conducted by using gas chromatograph mass spectrometer. Data obtained were then analyzed by using One-Way ANOVA test with p < 0.05. Results: After the level of polymerizing residual monomer with JIS method was compared to that at 70° C for 24 hours using microwave, it is known that there were significant differences (p < 0.05. Conclusion: The highest level of residual monomer of acrylic resin was that polymerized at 70° C for 24 hours.Latar belakang: Basis gigi tiruan yang berbahan dasar resin akrilik jenis heat cured setelah proses polimerisasi selesai masih mengandung monomer sisa yang berpotensi sebagai bahan iritan dalam rongga mulut. Proses polimerisasi sangat penting untuk mendapatkan resin akrilik yang memenuhi persyaratan biokompatibilitas dan fisik yang baik. Untuk persyaratan tersebut digunakan berbagai macam proses polimerisasi. Tujuan: Penelitian ini bertujuan untuk menentukan kadar monomer sisa resin akrilik yang diproses dengan metode

  2. Analysis of residual toluene in food packaging via headspace extraction method using gas chromatography

    International Nuclear Information System (INIS)

    Lim, Ying Chin; Mohd Marsin Sanagi

    2008-01-01

    Polymeric materials are used in many food contact applications as packaging material. The presence of residual toluene in this food packaging material can migrate into food and thus affect the quality of food. In this study, a manual headspace analysis was successfully designed and developed. The determination of residual toluene was carried out with standard addition method and multiple headspace extraction, MHE) method using gas chromatography-flame ionization detector, GC-FID). Identification of toluene was performed by comparison of its retention time with standard toluene and GC-MS. It was found that the suitable heating temperature was 180 degree Celsius with an optimum heating time of 10 minutes. The study also found that the concentration of residual toluene in multicolored sample was higher compared to mono colored sample whereas residual toluene in sample analyzed using standard addition method was higher compared to MHE method. However, comparison with the results obtained from De Paris laboratory, France found that MHE method gave higher accuracy for sample with low analyte concentration. On the other hand, lower accuracy was obtained for sample with high concentration of residual toluene due to systematic errors. Comparison between determination methods showed that MHE method is more precise compared to standard addition method. (author)

  3. Evaluation of residue management practices effects on corn productivity, soil quality, and greenhouse gas emissions

    Science.gov (United States)

    Guzman, Jose German

    The removal of crop residues left after harvest is being considered as a potential feedstock source for bioethanol production which can contribute to the reduction of fossil fuel use and net greenhouse gas (GHG). The objectives of this study were to: (i) examine how tillage, N fertilization rates, residue removal, and their interactions affect crop productivity, (ii) SOC and soil physical properties, and (iii) GHG emissions, and (iv) calculated a soil C budget to determine how much crop residue can be sustainably be removed in Central and Southwest Iowa. After three years of residue removal under different management practices, the findings of this study suggest that a portion of the corn residue that is left on the soil surface after harvest can be removed, with no negative impacts in the short term continuous corn yield in sites at Central and Southwest Iowa. However, significant decreases in SOC sequestration rates, microbial biomass-C, bulk density, soil penetration resistance, wet aggregate stability, and infiltration rates were observed, but varied with soil type and management practices. Additionally, soil surface CO2 and N2O emissions were responsive to management practices; primarily by altering soil temperature, soil water content, soil mineral N, and crop growth. Results from soil C budget show that in 2010 when corn growth was not water stressed (lack of moisture), approximately 35 and 30% of the residue could be sustainably removed in the Central and Southwest sites, respectively. In 2011, drier soil conditions resulted in approximately 2 and 49% of the residue could be sustainably removed in the Central and Southwest sites, respectively.

  4. Determination of insecticides malathion and lambda-cyhalothrin residues in zucchini by gas chromatography

    Directory of Open Access Journals (Sweden)

    Hayam M. Lofty

    2013-12-01

    Full Text Available A sensitive gas chromatographic method has been developed for the determination of malathion and lambda-cyhalothrin (λ-cyhalothrin insecticide residues in zucchini. The developed method consists of extraction with acetone, purification and partitioning with methylene chloride, column chromatographic clean-up, and finally capillary gas chromatographic determination of the insecticides. The recoveries of method were greater than 90% and limit of determination was 0.001 ppm for both insecticides. The method was applied to determine residues and the rate of disappearance of malathion and λ-cyhalothrin from fruits of zucchini (open field treatment, 50 cc of Malason/Cormandel 57% EC (emulsifiable concentrate for 100 L of water, 20 cc of LAMBDA SUPER FOG 5% liquid for 100 L of water. The insecticide incorporated into the plants decreased rapidly with a half-life time around 0.77 day (18.5h for malathion and 4 days for λ-cyhalothrin. It is not recommended to use zucchini before 12 h of malathion application. For λ-cyhalothrin, the preharvest interval is 5 days. Four market samples were chosen from different regions from A.R.E. and all of them showed no residues of malathion or λ-cyhalothrin.

  5. Alternative Gas Mixtures in Arc Spraying: A Chance to Improve Coating Properties and Residual Stress States

    Science.gov (United States)

    Hauer, Michél; Henkel, Knuth Michael; Krebs, Sebastian; Kroemmer, Werner

    2018-01-01

    The highly cavitation erosion-resistant propeller alloys CuAl9Ni5Fe4Mn (Ni-Al-Bronze) and CuMn13Al8Fe3Ni2 (Mn-Al-Bronze) were arc-sprayed using a mixture of nitrogen and 2% of hydrogen as atomizing gas and different traverse speeds. The objective was to identify the influences of the different spraying conditions, such as temperature regime and melting loss, on the resulting residual stress states and coating properties. Residual stresses were measured by the incremental hole-drilling method using ESPI. Temperature measurements were carried out by thermographic imaging. Microstructural, chemical and mechanical analyses were realized to examine adhesive and cohesive properties. Additionally, the cavitation erosion behavior was investigated to analyze cohesive coating properties. The spraying process itself was improved, which was apparent by mainly enhanced deposition efficiency and reduced surface temperatures. The amount of oxides and pores as well as the melting loss of alloying elements were reduced. Moreover, an increased cavitation erosion resistance and thus coating cohesion as well as less residual stresses were identified. The change in atomizing gas diminished the impact of the quenching stresses on the coating properties. In contrast, the adhesive strength, Young's moduli and partially the hardness were slightly reduced. With regard to materials, Ni-Al-Bronze revealed superior coating properties in comparison with Mn-Al-Bronze.

  6. Technical assessment of synthetic natural gas (SNG) production from agriculture residuals

    Science.gov (United States)

    Song, Guohui; Feng, Fei; Xiao, Jun; Shen, Laihong

    2013-08-01

    This paper presents thermodynamic evaluations of the agriculture residual-to-SNG process by thermochemical conversion, which mainly consists of the interconnected fluidized beds, hot gas cleaning, fluidized bed methanation reactor and Selexol absorption unit. The process was modeled using Aspen Plus software. The process performances, i.e., CH4 content in SNG, higher heating value and yield of SNG, exergy efficiencies with and without heat recovery, unit power consumption, were evaluated firstly. The results indicate that when the other parameters remain unchanged, the steam-to-biomass ratio at carbon boundary point is the optimal value for the process. Improving the preheating temperatures of air and gasifying agent is beneficial for the SNG yield and exergy efficiencies. Due to the effects of CO2 removal efficiency, there are two optimization objectives for the SNG production process: (I) to maximize CH4 content in SNG, or (II) to maximize SNG yield. Further, the comparison among different feedstocks indicates that the decreasing order of SNG yield is: corn stalk > wheat straw > rice straw. The evaluation on the potential of agriculture-based SNG shows that the potential annual production of agriculture residual-based SNG could be between 555×108 ˜ 611×108 m3 with utilization of 100% of the available unexplored resources. The agriculture residual-based SNG could play a significant role on solving the big shortfall of China's natural gas supply in future.

  7. Energy level transitions of gas in a 2D nanopore

    Energy Technology Data Exchange (ETDEWEB)

    Grinyaev, Yurii V., E-mail: grn@ispms.tsc.ru [Institute of Strength Physics and Materials Science SB RAS, Tomsk, 634055 (Russian Federation); National Research Tomsk State University, Tomsk, 634050 (Russian Federation); Chertova, Nadezhda V., E-mail: chertova@ispms.tsc.ru [Institute of Strength Physics and Materials Science SB RAS, Tomsk, 634055 (Russian Federation); Psakhie, Sergei G., E-mail: sp@ispms.tsc.ru [Institute of Strength Physics and Materials Science SB RAS, Tomsk, 634055 (Russian Federation); National Research Tomsk Polytechnic University, Tomsk, 634050 (Russian Federation)

    2015-10-27

    An analytical study of gas behavior in a 2D nanopore was performed. It is shown that the temperature dependence of gas energy can be stepwise due to transitions from one size-quantized subband to another. Taking into account quantum size effects results in energy level transitions governed by the nanopore size, temperature and gas density. This effect leads to an abrupt change of gas heat capacity in the nanopore at the above varying system parameters.

  8. Comparison of Postoperative Pain and Residual Gas Between Restrictive and Liberal Fluid Therapy in Patients Undergoing Laparoscopic Cholecystectomy.

    Science.gov (United States)

    Yao, Lei; Wang, Yulan; Du, Boxiang; Song, Jie; Ji, Fuhai

    2017-10-01

    Different fluid regimens are used in the clinical management of perioperative fluid therapy, but there still is the argument about which fluid regimen is better for patients. This study was mainly designed to compare different fluid regimens on postoperative pain and residual gas in patients undergoing laparoscopic cholecystectomy. A total of 100 patients were equally randomized to receive restrictive fluid infusion (n=50) with lactated Ringer (LR) solution 5 mL/kg/h or liberal fluid infusion (n=50), with 30 mL/kg/h lactated Ringer solution. Postoperative pain was evaluated at 1, 6, and 24 hours after surgery using a visual analog scale (VAS). Postoperative subdiaphragmatic residual gas was monitored by x-ray at 24 hours after surgery. Patients in the restrictive group had significantly higher VAS pain scores at 6 hours after surgery than those in the liberal group (P=0.009). The incidence of subdiaphragmatic residual gas in the restrictive group was higher than in the liberal group (P=0.045). Patients who had residual gas had higher VAS pain scores than those with no residual gas in the restrictive group at 6 hours after surgery (P=0.02). Patients undergoing laparoscopic cholecystectomy with restrictive fluid therapy may suffer more severe postoperative pain than those receiving liberal fluid therapy. It suggests that the higher incidence of subdiaphragmatic residual gas may have occurred with restrictive fluid therapy.

  9. Levels of pesticides residues in the White Nile water in the Sudan.

    Science.gov (United States)

    Nesser, Gibreel A A; Abdelbagi, Azhari O; Hammad, Ahmed Mohammed Ali; Tagelseed, Mirghani; Laing, Mark D

    2016-06-01

    Twenty-two commonly used pesticides were monitored during autumn, winter, and summer of 2004-2005 in 27 water samples from three sites along the White Nile in Sudan (former Sudan). Sites were selected to reflect pesticides gathered from drainage canals in central Sudan and from upstream sources. Collected samples were extracted and subjected to gas chromatographic analysis. Pesticides levels were measured in nanograms per liter. Pesticides residues were detected in 96 % of the samples with a total residue burden of 4132.6 ng L(-1), and an overall mean concentration and range of 50.99 and not detected-1570 ng L(-1), respectively. Ororganochlorines were the most frequently detected contaminants, which were found in 70 % of the samples, causing a total burden of 2852.8 ng L(-1), followed by pyrethroids 15 % of the samples, with a total burden of 926.5 ng L(-1). The tested herbicides were detected in ˂4 % of the samples with a total burden of 353.3 ng L(-1), while organophosphorus levels were below the detection limit. The most frequent contaminants were the following: heptachlor and its epoxide (52 % of samples), followed by DDTs (dichlorodiphenyltrichloroethanes) (DDT and DDE, in 19 % of the samples), cypermethrin and fenvalerate (in 11 % of the samples), and pendimethalin (in oxyfluorfen were not detected in the analyzed samples. Generally, levels were least in autumn, and followed by summer and winter. Sources of contamination might include agricultural lands in central Sudan and upstream sources. Both recent and old contaminations were indicated.

  10. Plasma sprayed hydroxyapatite coatings on titanium substrates. Part 1: Mechanical properties and residual stress levels.

    Science.gov (United States)

    Tsui, Y C; Doyle, C; Clyne, T W

    1998-11-01

    Hydroxyapatite (HA) coatings have been sprayed on to substrates of Ti-6Al-4V, using a range of input power levels and plasma gas mixtures. Coatings have also been produced on substrates of mild steel and tungsten, in order to explore certain aspects of the mechanical behaviour of HA without the complication of yielding or creep in the substrate. Studies have been made of the phase constitution, porosity, degree of crystallinity, OH ion content, microstructure and surface roughness of the HA coatings. The Young's moduli in tension and in compression were evaluated by the cantilever beam bend test using a tungsten/HA composite beam. The flexural Young's modulus was determined using a free-standing deposit under the same test. Adhesion was characterised using the single-edge notch-bend test; this is considered superior to the tensile bond strength test in common use. Measured interfacial fracture energies were of the order 1-10 J m(-2). Stress levels were investigated using specimen curvature measurements in conjunction with a numerical process model. The quenching stress for HA was measured to be about 10-25 MPa and the residual stress level in HA coatings at room temperature are predicted to lie in the approximate range of 20-40 MPa (tensile). These residual stresses could be reduced in magnitude by maintaining the substrate at a low temperature (possibly below room temperature) during spraying and it may be worthwhile to explore this. Ideally, the HA coating should have low porosity, high cohesive strength, good adhesion to the substrate, a high degree of crystallinity and high chemical purity and phase stability. In practice, such combinations are rather difficult to achieve by just varying the spraying parameters.

  11. A Simple and Rapid Extraction for Gas Chromatographic Determination of Thiabendazole and Imazalil Residues in Lemons

    Directory of Open Access Journals (Sweden)

    Navickiene Sandro

    2002-01-01

    Full Text Available A rapid and efficient method is described for the determination of thiabendazole and imazalil residues in lemons (peel and pulp. The procedure is based on the extraction with an hexane:ethyl acetate mixture (1:1, v/v and gas chromatographic analysis using thermionic specific detection (TSD. The possibility of matrix effect was also studied. Mean recoveries from 8 replicates of fortified samples ranged from 79% to 109%, with relative standard deviation values between 2.4% to 12.8%. The detection and quantification limits of the method were 0.2 mg kg-1 and 0.5 mg kg-1, respectively.

  12. Effect of household and industrial processing on levels of pesticide residues and degradation products in melons

    OpenAIRE

    Bonnechère, Aurore; Hanot, Vincent; Bragard, Claude; Bedoret, Thomas; Van Loco, Joris

    2012-01-01

    Abstract Two varieties of melons (Cucumis melo) were treated by two fungicides (carbendazim and maneb) and four insecticides (acetamiprid, cyromazin, imazalil and thiamethoxam) to quantify the effect of household processing on the pesticide residues. To ensure sufficiently high levels of residues in flesh and peels, the most concentrated formulations were applied pursuant to Good Agricultural Practices (GAPs). The peeling step decreased the concentration of pesticide residues for ...

  13. Acoustical gas-leak detection in the presence of multiple reflections, dispersion, and uncorrelated noise using optimized residual complexity.

    Science.gov (United States)

    Ahmadi, A M; Amjadi, A; Bahrampour, A R; Ravanbod, H; Tofighi, S

    2016-09-01

    Precise acoustical leak detection calls for robust time-delay estimates, which minimize the probability of false alarms in the face of dispersive propagation, multiple reflections, and uncorrelated background noise. Providing evidence that higher order modes and multi-reflected signals behave like sets of correlated noise, this work uses a regression model to optimize residual complexity in the presence of both correlated and uncorrelated noise. This optimized residual complexity (ORC) is highly robust since it takes into account both the level and complexity of noise. The lower complexity of the dispersive modes and multiple reflections, compared to the complexity of the plane mode, points to the robustness of ORC against multiple reflections and dispersion. Experimental investigations using recorded sounds of gas leaking from a pipe confirm the robustness of ORC against multiple reflections. Numerical simulations also show robustness against dispersive modes, even when they disturb the linearity of the cross-spectrum phase. Comparisons with other methods-mutual information, cross correlation, and residual complexity-underline the general advantages of ORC in terms of robustness in the presence of reflection and dispersion, against both correlated and uncorrelated noise, and to short signals.

  14. Analysis of Petroleum Products in Fire Debris Residues by Gas Chromatography: A Literature Review

    Directory of Open Access Journals (Sweden)

    Gurvinder Singh Bumbrah

    2017-06-01

    Full Text Available This review gives a brief overview of developments in the analysis of petroleum products (PP in fire debris residues (FDR by gas chromatography (GC. The review covers different aspects of analysis such as the substrates involved, isolation procedures, column and mobile phase used, and subsequent detection in tabular form. This paper covers detection of PP such as petrol, kerosene, and diesel in various types’ of samples of interest to fire debris analysts. Solid phase microextraction is most frequently used along with gas chromatography-mass spectrometry (GC-MS for the extraction and identification of PP from FDR. Chemometric tools should be used to improve the significance and reliability of results obtained from the analysis of FDR. However, the potential utility of portable GC-MS in fire debris analysis cannot be ignored, and its proper development and validation is required before using it for this purpose.

  15. Determination of 86 Pesticide Residues in Leafy Vegetables using gas Chromatography Mass Spectrometry

    OpenAIRE

    , M. T. Selim; , I. Al-Dossary

    2016-01-01

    A multiresidue method is described for detection and determination of 86 compounds of pesticide residues which commonly used in the pest control programs for crop protection. Good sensitivity and selectivity of the method are obtained with limits of quantiŞcation 0.01 mg/kg in almost all cases. The method was applied very satisfactorily to routine analysis as a complement to traditional GC-MS method and Şnally, limit of detection were also 10-20 times lower than maximum residue levels (MRL) e...

  16. Laboratory-based validation of the baseline sensors of the ITER diagnostic residual gas analyzer

    Energy Technology Data Exchange (ETDEWEB)

    Biewer, Theodore M. [ORNL; Marcus, Chris [ORNL; Klepper, C Christopher [ORNL; Andrew, Philip [ITER Organization, Cadarache, France; Gardner, W. L. [United States ITER Project Office; Graves, Van B. [ORNL; Hughes, Shaun [ITER Organization, Saint Paul Lez Durance, France

    2017-10-01

    The divertor-specific ITER Diagnostic Residual Gas Analyzer (DRGA) will provide essential information relating to DT fusion plasma performance. This includes pulse-resolving measurements of the fuel isotopic mix reaching the pumping ducts, as well as the concentration of the helium generated as the ash of the fusion reaction. In the present baseline design, the cluster of sensors attached to this diagnostic's differentially pumped analysis chamber assembly includes a radiation compatible version of a commercial quadrupole mass spectrometer, as well as an optical gas analyzer using a plasma-based light excitation source. This paper reports on a laboratory study intended to validate the performance of this sensor cluster, with emphasis on the detection limit of the isotopic measurement. This validation study was carried out in a laboratory set-up that closely prototyped the analysis chamber assembly configuration of the baseline design. This includes an ITER-specific placement of the optical gas measurement downstream from the first turbine of the chamber's turbo-molecular pump to provide sufficient light emission while preserving the gas dynamics conditions that allow for \\textasciitilde 1 s response time from the sensor cluster [1].

  17. Laboratory-based validation of the baseline sensors of the ITER diagnostic residual gas analyzer

    Science.gov (United States)

    Klepper, C. C.; Biewer, T. M.; Marcus, C.; Andrew, P.; Gardner, W. L.; Graves, V. B.; Hughes, S.

    2017-10-01

    The divertor-specific ITER Diagnostic Residual Gas Analyzer (DRGA) will provide essential information relating to DT fusion plasma performance. This includes pulse-resolving measurements of the fuel isotopic mix reaching the pumping ducts, as well as the concentration of the helium generated as the ash of the fusion reaction. In the present baseline design, the cluster of sensors attached to this diagnostic's differentially pumped analysis chamber assembly includes a radiation compatible version of a commercial quadrupole mass spectrometer, as well as an optical gas analyzer using a plasma-based light excitation source. This paper reports on a laboratory study intended to validate the performance of this sensor cluster, with emphasis on the detection limit of the isotopic measurement. This validation study was carried out in a laboratory set-up that closely prototyped the analysis chamber assembly configuration of the baseline design. This includes an ITER-specific placement of the optical gas measurement downstream from the first turbine of the chamber's turbo-molecular pump to provide sufficient light emission while preserving the gas dynamics conditions that allow for \\textasciitilde 1 s response time from the sensor cluster [1].

  18. [Determination of residual toluene diisocyanate in sponge bra by gas chromatography].

    Science.gov (United States)

    Wang, Aixia; Ye, Ping; Huang, Nan; Chen, Yan; Li, Xinggen

    2017-06-08

    A gas chromatography (GC) with internal standard method was developed for the determination of residual toluene diisocyanate (TDI) in sponge bra. The samples were extracted with ethyl acetate dehydrated, and cleaned up with 0.22 μm microfiltration membrane. The residual toluene diisocyanate was separated on a DB-624 capillary column using temperature programming. The flame ionization detector (FID) was used at 250 ℃. The inlet temperature was 180 ℃ with nitrogen as carrier gas. The linear range was 10-200 mg/L ( R 2 =0.9989) for TDI. The average recovery ranged from 80.5% to 91.6% with RSD not more than 7.9%( n =6). The limit of detection (LOD) and limit of quantification (LOQ) were 10 mg/kg and 100 mg/kg, respectively. The developed method was then utilized to analyse the 100 batches of sponge bra samples from the manufacturing enterprises, the entity shops and electric business platforms. The method is simple, time-saving and environment friendly with high sensitivity and good reproducibility, and has practical application value due to its low-cost and short-circle.

  19. On residual gas analysis during high temperature baking of graphite tiles

    International Nuclear Information System (INIS)

    Prakash, A A; Chaudhuri, P; Khirwadkar, S; Reddy, D Chenna; Saxena, Y C; Chauhan, N; Raole, P M

    2008-01-01

    Steady-state Super-conducting Tokamak-1 (SST-1) is a medium size tokamak with major radius of 1.1 m and minor radius of 0.20 m. It is designed for plasma discharge duration of 1000 seconds to obtain fully steady-state plasma operation. Plasma Facing Components (PFC), consisting of divertors, passive stabilizers, baffles and poloidal limiters are also designed to be UHV compatible for steady state operation. All PFC are made up of graphite tiles mechanically attached to the copper alloy substrate. Graphite is one of the preferred first wall armour material in present day tokamaks. High thermal shock resistance and low atomic number of carbon are the most important properties of graphite for this application. High temperature vacuum baking of graphite tiles is the standard process to remove the impurities. Residual Gas Analyzer (RGA) has been used for qualitative and quantitative measurements of released gases from graphite tiles during baking. Surface Analysis of graphite tiles has also been done before and after baking. This paper describes the residual gas analysis during baking and surface analysis of graphite tiles

  20. On residual gas analysis during high temperature baking of graphite tiles

    Science.gov (United States)

    Prakash, A. A.; Chaudhuri, P.; Khirwadkar, S.; Chauhan, N.; Raole, P. M.; Reddy, D. Chenna; Saxena, Y. C.

    2008-05-01

    Steady-state Super-conducting Tokamak-1 (SST-1) is a medium size tokamak with major radius of 1.1 m and minor radius of 0.20 m. It is designed for plasma discharge duration of 1000 seconds to obtain fully steady-state plasma operation. Plasma Facing Components (PFC), consisting of divertors, passive stabilizers, baffles and poloidal limiters are also designed to be UHV compatible for steady state operation. All PFC are made up of graphite tiles mechanically attached to the copper alloy substrate. Graphite is one of the preferred first wall armour material in present day tokamaks. High thermal shock resistance and low atomic number of carbon are the most important properties of graphite for this application. High temperature vacuum baking of graphite tiles is the standard process to remove the impurities. Residual Gas Analyzer (RGA) has been used for qualitative and quantitative measurements of released gases from graphite tiles during baking. Surface Analysis of graphite tiles has also been done before and after baking. This paper describes the residual gas analysis during baking and surface analysis of graphite tiles.

  1. Determination of residual dimethylsulphoxide in drug loaded gelatin using thermal desorber - gas chromatography.

    Science.gov (United States)

    Asfaw, Adissu Alemayehu; Wolfs, Kris; Van Schepdael, Ann; Adams, Erwin

    2018-05-10

    Traditional headspace - gas chromatography (HS-GC) methods for the determination of residual solvents (RS) start from a homogenous sample solution. Subsequently, it is challenging to determine RS using HS-GC techniques from insoluble solid samples like gelatin which is practically impossible to dissolve or distribute uniformly in water and common organic solvents. In this study, a thermal desorber combined with capillary gas chromatography and flame ionization detection/mass spectrometry (TD-GC-FID/MS) was used for quantitative determination of residual dimethylsulfoxide (DMSO) in gelatin without sample pretreatment. A sample of gelatin was sandwiched between two quartz filter double layers in a polytetrafluoroethylene insert which was then placed in its entirety into a thermal desorption tube. Factors affecting the performance of TD-GC including desorption time, desorption temperature, desorption flow and type of adsorbent were studied by applying a standard solution of DMSO in methanol on a blank gelatin bed. Validation results of the proposed method showed good linearity with an R 2 -value higher than 0.999 for a wide concentration range and good sensitivity with a limit of detection and limit of quantification of 0.1 μg and 0.2 μg on tube, respectively. The proposed method shows recovery values close to 100%. In addition, a conventional HS-GC method following enzymatic degradation of gelatin was developed to verify the proposed TD-GC method. Both methods were applied for the determination of residual DMSO in gelatin that was loaded with an experimental drug. Results were comparable, but the enzyme assisted HS-GC method was more time consuming and expensive. Copyright © 2018 Elsevier B.V. All rights reserved.

  2. Simultaneous determination of lincomycin and spectinomycin residues in animal tissues by gas chromatography-nitrogen phosphorus detection and gas chromatography-mass spectrometry with accelerated solvent extraction.

    Science.gov (United States)

    Tao, Y; Chen, D; Yu, G; Yu, H; Pan, Y; Wang, Y; Huang, L; Yuan, Z

    2011-02-01

    A new multi-dimensional analytical method using gas chromatography-nitrogen phosphorus detection (GC-NPD) and gas chromatography-mass spectrometry (GC-MS) was developed for qualitative and quantitative measurement of lincomycin and spectinomycin residues in food animal tissues. This method is based on a new extraction procedure using accelerated solvent extraction (ASE). The analytes were extracted by phosphate buffer with trichloroacetic acid deproteinization and clean-up by C₁₈ solid-phase extraction (SPE) adding dodecanesulfonic acid sodium salt as an ion-pair reagent. The eluted fraction was evaporated and derivatised with N,O-bis(trimethylsilyl) trifluoroacetamide (BSTFA) for GC-NPD analysis and GC-MS confirmation. Parameters for extraction pressure, temperature and cycle of ASE, clean-up, derivatisation and analysis procedure were optimised. The method was validated in muscle, kidney and liver of swine, bovine with a low concentration (limit of quantification) of 16.4 and 21.4 µg kg⁻¹ for these two analytes using GC-NPD. For GC-MS, the limits of quantification were 4.1 and 5.6 µg kg⁻¹, respectively. Spiked recoveries from levels of 20 to 200 µg kg⁻¹ were found to be between 73% and 99% with a relative standard deviation (RSD) of less than 17% in GC-NPD. For GC-MS, levels from 5 to 20 µg kg⁻¹ had between 70% and 93% with an RSD of less than 21%. This rapid and reliable method can be used for the characterisation and quantification of residues of lincomycin and spectinomycin in animal tissues.

  3. Computer simulation of void formation in residual gas atom free metals by dual beam irradiation experiments

    International Nuclear Information System (INIS)

    Shimomura, Y.; Nishiguchi, R.; La Rubia, T.D. de; Guinan, M.W.

    1992-01-01

    In our recent experiments (1), we found that voids nucleate at vacancy clusters which trap gas atoms such as hydrogen and helium in ion- and neutron-irradiated copper. A molecular dynamics computer simulation, which implements an empirical embedded atom method to calculate forces that act on atoms in metals, suggests that a void nucleation occurs in pure copper at six and seven vacancy clusters. The structure of six and seven vacancy clusters in copper fluctuates between a stacking fault tetrahedron and a void. When a hydrogen is trapped at voids of six and seven vacancy, a void can keep their structure for appreciably long time; that is, the void do not relax to a stacking fault tetrahedron and grows to a large void. In order to explore the detailed atomics of void formation, it is emphasized that dual-beam irradiation experiments that utilize beams of gas atoms and self-ions should be carried out with residual gas atom free metal specimens. (author)

  4. Multi-Residue Analysis of Pesticides in Pistachio Using Gas Chromatography-Mass Spectrometry (GC/MS

    Directory of Open Access Journals (Sweden)

    Azadeh Emami

    2014-12-01

    Full Text Available Background: Analysis of pesticide residues in food and other environmental commodities have become an essential requirement for consumers, producers, food inspectors and authorities. This study is focused on validation of an accurate, rapid and reliable method for multi-residual analysis of pesticides in pistachio as a strategic crop for export and one of the main nuts in Iranian food basket. Methods: We developed a "Quick, Easy, Cheap, Effective, Rugged, and Safe (QuEChERS method based on spiking blank samples and used the data for drawing calibration curves instead of standard solutions. Sample preparations were developed for determination of 12 pesticide residues in pistachio by gas chromatography-mass spectrometry (GC/MS. Results: Recovery of pesticides at 5 concentration levels (n=3 was in the range of 81.40% - 93.08 %. The method proved to be repeatable in the majority of samples with relative standard deviation (RSD of lower than 20%. The limits of detection and quantification for all pesticides were 2 ppb and 10 ppb, respectively. Conclusion: The calibration curves of pesticides were linear in the range of 10-500 (ng/g and correlation coefficient of entire pesticides was higher than 0.994. The recovery of pesticides at 5 concentration levels (n=3 was in range of 81.41- 91.80 %. The method was proved to be repeatable with the majority of RSDs being lower than 20%. The limits of detection and quantification for all pesticides were 2 and 10 ppb, respectively. The recoveries and repeatabilities were in accordance with the criteria set by SANCO Guideline (Commission of the European Communities, 2006.

  5. Morphogenic and structural traits of Brachiaria brizantha cv. Marandu under different nitrogen levels and residues heights

    Directory of Open Access Journals (Sweden)

    Eleuza Clarete Junqueira de Sales

    2014-10-01

    Full Text Available The objective of this study was to evaluate the rate of leaf appearance, leaf elongation rate, number of green leaves, length of blade and stem of Brachiaria brizantha cv. Marandu under different nitrogen levels and two residue heights. A randomized block design was used in a 4 x 2 factorial scheme, four doses of nitrogen (100, 200, 300 and 400 kg N ha-1 year-1 and two residue heights (5 and 15 cm. There was significant interaction between residue height and nitrogen levels for leaf appearance rate (P> 0.05 of signal grass, which was influenced negatively and linearly (P 0.05 between the levels of nitrogen x residue height on the number of green leaves. The dosage that provided the highest stalk in the residue height of 5 cm was of 271.5 kg N ha -1. An increase of 0.0745 cm tiller -1 day-1 for 1 kg of N ha -1 applied to height of 15 cm of residue was observed. Nitrogen fertilization contributes positively to growth and development of rates of appearance and leaf extension. The management of pasture of Brachiaria brizantha cv. Marandu with 5 cm of residue and fertilization with 100 kg N ha -1 provided better answer morphogenic traits.

  6. Electron space charge effects in ion sources for residual gas analysis

    International Nuclear Information System (INIS)

    Cowen, M.C.; Allison, W.

    1993-01-01

    An electron impact ionization source suitable for residual gas analysis (RGA) with a quadrupole mass spectrometer has been studied both experimentally and by computer simulation. The electronic space charge is shown to play a role in limiting the extracted current from RGA ion sources and the simulation treats this aspect of the problem self-consistently. Under certain source conditions, the ion extraction efficiency is observed to decrease for electron currents above approximately 1 mA - well below the current at which space charge limiting of the electron emission is expected. The observed effects are well reproduced by the simulation. We show that whereas the electron trajectories are only weakly perturbed by space charge effects, the loss of ionization efficiency can be attributed to drastic changes in the ion trajectories. (author)

  7. Comparison pesticide residue levels in the surface of Bertam River in Cameron Highlands, Pahang

    Energy Technology Data Exchange (ETDEWEB)

    Haron, S. H., E-mail: ismail@ukm.edu.my; Ismail, B. S., E-mail: sthumaira@yahoo.com [School of Environmental and Natural Resource Sciences, Faculty of Science and Technology, Universiti Kebangsaan Malaysia 43600 UKM, Bangi, Selangor (Malaysia)

    2015-09-25

    The presence of pesticide residues in the surface water of Bertam River in the agricultural areas of Cameron Highlands in Pahang, Malaysia was monitored from May to October 2014. The sampling sites were located at 10 sampling points along the Bertam River in the vegetable planting areas. The extraction method of the pesticide (organophosphate/pyrethroid) from the river samples used solid phase extraction followed by gas chromatography (with electron capture detector, ECD). Insecticides, cypermethrin and chlorpyrifos were found in the surface water of Bertam River. High level concentrations of those insecticides in the river were observed during the period from May to October 2014, a period which included both seasons (wet and dry seasons). The highest concentration of 2.66 µg/mL and 1.23 µg/mL of cypermethrin was observed during the wet and dry seasons respectively. This could be due to the frequent usage of the above-mentioned insecticides coupled with contamination that could have originated from the application sites. Meanwhile, the lowest concentration detected in the surface water was chlorpyrifos (0.11 µg/mL and 0.17 µg/mL) during the dry and wet seasons, respectively.

  8. Comparison pesticide residue levels in the surface of Bertam River in Cameron Highlands, Pahang

    International Nuclear Information System (INIS)

    Haron, S. H.; Ismail, B. S.

    2015-01-01

    The presence of pesticide residues in the surface water of Bertam River in the agricultural areas of Cameron Highlands in Pahang, Malaysia was monitored from May to October 2014. The sampling sites were located at 10 sampling points along the Bertam River in the vegetable planting areas. The extraction method of the pesticide (organophosphate/pyrethroid) from the river samples used solid phase extraction followed by gas chromatography (with electron capture detector, ECD). Insecticides, cypermethrin and chlorpyrifos were found in the surface water of Bertam River. High level concentrations of those insecticides in the river were observed during the period from May to October 2014, a period which included both seasons (wet and dry seasons). The highest concentration of 2.66 µg/mL and 1.23 µg/mL of cypermethrin was observed during the wet and dry seasons respectively. This could be due to the frequent usage of the above-mentioned insecticides coupled with contamination that could have originated from the application sites. Meanwhile, the lowest concentration detected in the surface water was chlorpyrifos (0.11 µg/mL and 0.17 µg/mL) during the dry and wet seasons, respectively

  9. Pyrolysis of automotive shredder residue for the production of fuel-grade gas

    International Nuclear Information System (INIS)

    Sharp, L.L.; Ness, R.O. Jr.

    1993-01-01

    Every year eight to ten million cars and trucks are disposed of by shredding at one of the 200 auto shredders located in the United States. Automotive shredder residue (ASR) is a by-product created in the dismantling of automobiles. Figure 1 illustrates the process by which ASR is generated. An automobile is stripped of useful and/or hazardous items, such as the gas tank, battery, tires, and radiator. Although it is beneficial to have these items removed for safety and environmental concerns, this is not always accomplished. After removal of some or all of these items, the automobile is shredded to provide a material less than 4 inches in size and composed of approximately 50% organic and 50% inorganic fractions. Ferrous scrap is then separated out magnetically. This ferrous scrap supplies the steel industry with 12 to 14 million tons per year for electric arc furnace feedstock. Air cyclone separators isolate a low density open-quotes fluffclose quotes from the nonferrous fraction (aluminum, copper, etc.). This fluff (shredder residue) is composed of a variety of plastics, fabrics, foams, glass, rubber, and an assortment of contaminants. Fluff bulk density is approximately 20 lb/ft

  10. Procedure of Active Residual Heat Removal after Emergency Shutdown of High-Temperature-Gas-Cooled Reactor

    Directory of Open Access Journals (Sweden)

    Xingtuan Yang

    2014-01-01

    Full Text Available After emergency shutdown of high-temperature-gas-cooled reactor, the residual heat of the reactor core should be removed. As the natural circulation process spends too long period of time to be utilized, an active residual heat removal procedure is needed, which makes use of steam generator and start-up loop. During this procedure, the structure of steam generator may suffer cold/heat shock because of the sudden load of coolant or hot helium at the first few minutes. Transient analysis was carried out based on a one-dimensional mathematical model for steam generator and steam pipe of start-up loop to achieve safety and reliability. The results show that steam generator should be discharged and precooled; otherwise, boiling will arise and introduce a cold shock to the boiling tubes and tube sheet when coolant began to circulate prior to the helium. Additionally, in avoiding heat shock caused by the sudden load of helium, the helium circulation should be restricted to start with an extreme low flow rate; meanwhile, the coolant of steam generator (water should have flow rate as large as possible. Finally, a four-step procedure with precooling process of steam generator was recommended; sensitive study for the main parameters was conducted.

  11. Multipesticide residue levels in UHT and raw milk samples by GC-μECD after QuEChER extraction method.

    Science.gov (United States)

    Jawaid, Sana; Talpur, Farah N; Nizamani, Shafi M; Khaskheli, Abid A; Afridi, H I

    2016-04-01

    In the present study, milk samples including raw and ultra-high temperature (UHT) processed milk were analyzed for pesticide residue levels, including five pesticides, viz chloripyrifos, endosulfan (α and β), profenofos and bifenthrin by gas chromatography microelectron capture detector (GC-μECD) after extraction by QuEChERS method. Further confirmation of the pesticide residue was done by GC-MS. The pesticide residual level in raw and UHT milk samples (n = 70) was determined in the range of 0.1-30 μg L(-1). All UHT processed milk samples contain pesticide residues within permissible limit set by the World Health Organization (WHO); however, among raw milk samples, chloripyrifos (12 %), α (24 %), and β (14 %) endosulfan were found above the maximum residue limit (MRL). The estimated daily intake (EDI) of these four pesticide residues were also calculated as 1.32, 16.16, 5.30, 10.20, and 9.93 μg kg(-1) body weight for chloripyrifos, endosulfan α, profenofos, endosulfan β, and bifenthrin, respectively. It is concluded that the raw milk samples showed higher prevalence of pesticide residues as compared to UHT processed milk. Graphical abstract Determination of pesticide residues in dairy milk by GC-μECD after QuEChERS extraction method.

  12. Gas Chromatographic Method: Tool for Rapid and Sensitive Analysis of Residual Solvents in Amoxicillin and Ampicillin Tablets

    Directory of Open Access Journals (Sweden)

    Sk Manirul Haque

    2015-12-01

    Full Text Available A simple and sensitive static head space gas chromatographic (SH-GC method equipped with FID has been developed and validated for simultaneous determination of residual solvents e.g.,  methanol, dichloromethane and toluene in two therapeutic drugs such as amoxicillin  and ampicillin. The separation was achieved with 30 m long Elite - 5 fused silica capillary column and 0.32 mm inner diameter. The developed SH-GC method offered symmetric peak shape, good resolution and reasonable retention time for all the solvents. Beer’s law was obeyed in the concentration ranges 100 – 1200, 50 – 1000 and 50 – 500 ppm for methanol, dichloromethane and toluene, respectively. The method was validated according to international conference on harmonization (ICH guidelines in terms of specificity, linearity, precision, accuracy, limit of detection, limit of quantitation, robustness and solution stability. The degrees of linearity of the calibration curves, the percent recoveries, relative standard deviation for the method were also determined. All the validation parameters were within the acceptable range. The developed SH-GC method could, therefore, be suitable for simple and rapid detection of trace levels residual solvents in other pharmaceutical products and thereby it could be used for routine analysis in any analytical laboratory.

  13. Influence of different disease control pesticide strategies on multiple pesticide residue levels in apple

    DEFF Research Database (Denmark)

    Poulsen, Mette Erecius; Naef, A.; Gasser, S.

    2009-01-01

    Seven pesticide application strategies were investigated to control apple scab (Venturia inaequalis) and powdery mildew (Podosphaera leucotricha) and, at the same time.. fulfil the new quality standards implemented by some German retailers. These demand that pesticide residues should be below 80......% of European Maximum Residue Levels (EU MRL) and that the number of residues present at levels above 0.01 mg kg(-1) should be limited to a maximum of four. The strategies fulfilled the requirement to use combinations of different active substances in order to prevent the emergence of resistance to pesticides....... The trials were conducted at two sites in Switzerland, in 2007, and all strategies and applications were in accordance with actual practice. Four replicates of apple samples from each strategy were then analysed for pesticide residues. The incidence of infection with apple scab and powdery mildew were...

  14. Rapid gas chromatographic method for the determination of famoxadone, trifloxystrobin and fenhexamid residues in tomato, grape and wine samples.

    Science.gov (United States)

    Likas, D T; Tsiropoulos, N G; Miliadis, G E

    2007-05-25

    Trifloxystrobin, fenhexamid and famoxadone belong to the generation of fungicides acting against a broad spectrum of fungi and widely used in Integrated Pest Management strategies in different agricultural crops but mainly in viticulture. In the present work, a gas chromatographic (GC) method for their determination was developed and validated on tomato, grape and wine matrices. The method was based on a simple one step liquid-liquid microextraction with cyclohexane/dichloromethane (9+1, v/v) and determination of fungicides by gas chromatography with nitrogen phosphorous (NP-) and electron capture (EC-) detection, and ion trap mass spectrometry (ITMS) for confirmation. The method was validated by recovery experiments, assessment of matrix effect and calculation of the associated uncertainty. Recoveries for GC-NPD and GC-ECD were found in the range of 81-102% with RSD NPD, respectively, depending on the sensitivity of each compound with trifloxystrobin being the most sensitive. The expanded uncertainty, calculated for a sample concentration of 0.10 mg/kg, ranged from 4.8 to 13% for the GC-ECD and from 5.4 to 29% for the GC-NPD. The concentration levels for famoxadone residues found in tomato and grape samples from field experiments were clearly below the EU established MRL values, thus causing no problems in terms of food safety.

  15. Quantifying and reporting greenhouse gas emissions at local level

    OpenAIRE

    Sόwka Izabela; Bezyk Yaroslav

    2017-01-01

    Cities as global centers of consumption and production often are a significant and growing source of greenhouse gas (GHG) emissions. At the same time, local authorities are increasingly taking action on climate change by focusing on reducing GHG emissions and efficiency improvement opportunities. To assess and reduce the overall greenhouse gas emission level from an urban area, it is necessary to identify all the activities and processes which generate these emissions. GHG inventory gives an ...

  16. Methodology for determining acceptable residual radioactive contamination levels at decommissioned nuclear facilities/sites

    International Nuclear Information System (INIS)

    Watson, E.C.; Kennedy, W.E. Jr.; Hoenes, G.R.; Waite, D.A.

    1979-01-01

    The ultimate disposition of decommissioned nuclear facilities and their surrrounding sites depends upon the degree and type of residual contamination. Examination of existing guidelines and regulations has led to the conclusion that there is a need for a general method to derive residual radioactive contamination levels that are acceptable for public use of any decommissioned nuclear facility or site. This paper describes a methodology for determining acceptable residual radioactive contamination levels based on the concept of limiting the annual dose to members of the public. It is not the purpose of this paper to recommend or even propose dose limits for the exposure of the public to residual radioactive contamination left at decommissioned nuclear facilities or sites. Unrestricted release of facilities and/or land is based on the premise that the potential annual dose to any member of the public using this property from all possible exposure pathways will not exceed appropriate limits as may be defined by Federal regulatory agencies. For decommissioned land areas, consideration should be given to people living directly on previously contaminated areas, growing crops, grazing food animals and using well water. Mixtures of radionuclides in the residual contamination representative of fuel reprocessing plants, light water reactors and their respective sites are presented. These mixtures are then used to demonstrate the methodology. Example acceptable residual radioactive contamination levels, based on an assumed maximum annual dose of one millirem, are calculated for several selected times following shutdown of a facility. It is concluded that the methodology presented in this paper results in defensible acceptable residual contamination levels that are directly relatable to risk assessment with the proviso that an acceptable limit to the maximum annual dose will be established. (author)

  17. Residual solvent determination by head space gas chromatography with flame ionization detector in omeprazole API

    Directory of Open Access Journals (Sweden)

    Saurabh Pandey

    2011-06-01

    Full Text Available Residual solvents in pharmaceutical samples are monitored using gas chromatography with head space. Based on good manufacturing practices, measuring residual solvents is mandatory for the release testing of all active pharmaceutical ingredients (API. The analysis of residual organic solvents (methanol, acetone, cyclohexane, dichloromethane, toluene in Omeprazole, an active pharmaceutical ingredient was investigated. Omeprazole is a potent reversible inhibitor of the gastric proton pump H+/K+-ATPase. The Head space gas chromatography (HSGC method described in this investigation utilized a SPB TM-624, Supelco, 30 m long x 0.25 mm internal diameter, 1.4µm-thick column. Since Omeprazole is a thermally labile compound, the selection of the proper injector temperature is critical to the success of the analysis. The injector temperature was set at 170ºC to prevent degradation. The initial oven temperature was set at 40ºC for 12 min and programmed at a rate of 10ºC min-1 to a final temperature of 220ºC for 5 min. Nitrogen was used as a carrier gas. The sample solvent selected was N,N-dimethylacetamide. The method was validated to be specific, linear, precise, sensitive, rugged and showed excellent recovery.Solventes residuais em amostras farmacêuticas são monitoradas utilizando-se cromatografia a gás "headspace". Com base nas boas práticas de fabricação, a medida de solventes residuais é obrigatória para o teste de liberação de todos os ingredientes farmacêuticos (API. Efetuou-se a análise de solventes orgânicos residuais (metanol, acetona, cicloexano, diclorometano, tolueno em omeprazol, ingrediente farmacêutico ativo. O omeprazol é potente inibidor reversível da bomba de prótons H+/K+-ATPase. A cromatografia a gás "headspace" (HSGC descrita nessa pesquisa utilizou um SPB TM-624, Supelco, de 30 m de comprimento x 0,25 mm de diâmetro interno, e coluna de 1,4 µm de espessura. Considerando-se que o omeprazol é termicamente l

  18. Morphology and composition of pyrotechnic residues formed at different levels of confinement.

    Science.gov (United States)

    Vermeij, Erwin; Duvalois, Willem; Webb, Rutger; Koeberg, Mattijs

    2009-04-15

    Post explosion residues (PER) are residues from pyrotechnic compositions or explosives that are generated during an explosion. In the recent past SEM/EDX was used several times to analyze PER from pyrotechnic compositions. The results from these studies suggest that there might be a difference in morphology and composition of pyrotechnic residues formed at different levels of confinement. Also because of general thermodynamic principles it is believed that at higher levels of confinement the final pressure and temperature during the explosion is probably (but not necessarily) higher, eventually resulting in smaller and more spherical particles and a more homogeneous elemental composition. If there is a relation between morphology and composition of pyrotechnic residues and the level of confinement at which these are formed, it would be possible to draw conclusions about the conditions at which pyrotechnic residues were formed and the kind and construction of the device used. This may aid forensic scientists not only in the determination of the original explosive composition, but also of the explosive device. To perform controlled experiments with pyrotechnic charges at, at least, two pre-set levels of confinement a test vessel was built by TNO Defence, Security and Safety. For this study, three different flash powder compositions and black powder were selected. The generated residues were sampled on collecting plates and Nucleopore filters connected to a pump system in the immediate vicinity of the venting area for further analyses by SEM/EDX and XRD. From the results it follows that in the pressure range studied, the level of confinement seems to have a minor effect on the features of the generated residue particles. Because passive sampling by means of collector plates seemed doubtful and because the number of experiments had to be limited it is impossible to draw definitive conclusions. In addition to the level of confinement several other variables may affect

  19. Residue analysis of organophosphorus and organochlorine pesticides in fatty matrices by gas chromatography coupled with electron-capture detection.

    Science.gov (United States)

    Park, Jae-Woo; Abd El-Aty, A M; Lee, Myoung-Heon; Song, Sung-Ok; Shim, Jae-Han

    2006-01-01

    A multiresidue method for the simultaneous determination of 22 organochlorine (OCs) and organophosphorus (Ops) pesticides (including isomers and metabolites), representing a wide range of physicochemical properties, was developed in fatty matrices extracted from meat. Pesticides were extracted from samples with acetonitrile/n-hexane (v:v, 1:1). The analytical screening was performed by gas chromatography coupled with electron-capture detection (ECD). The identification of compounds was based on their retention time and on comparison of the primary and secondary ions. The optimized method was validated by determining accuracy (recovery percentages), precision (repeatability and reproducibility), and sensitivity (detection and quantitation limits) from analyses of samples fortified at 38 to 300 ng/g levels. Correlation coefficients for the 22 extracted pesticide standard curves (linear regression analysis, n = 3) ranged from 0.998 to 1.000. Recovery studies from 2 g samples fortified at 3 levels demonstrated that the GC-ECD method provides 64.4-96.0% recovery for all pesticides except 2,4'-DDE (44.6-50.4%), 4,4'-DDE (51.1-57.5%) and 2,4'-DDT (50.0-51.2%). Both repeatability and reproducibility relative standard deviation values were < 20% for all residues. Detection limits ranged from 0.31 to 1.27 ng/g and quantification limits were between 1.04 and 4.25 ng/g. The proposed analytical method may be used as a simple procedure in routine determinations of OCs and Ops in meat. It can also be applied to the determination of pesticide multi-residues in other animal products such as butter and milk.

  20. Determination of pesticide residues in animal origin baby foods by gas chromatography coupled with triple quadrupole mass spectrometry.

    Science.gov (United States)

    Amendola, Graziella; Pelosi, Patrizia; Attard Barbini, Danilo

    2015-01-01

    A simple, fast and multiresidue method for the determination of pesticide residues in baby foods of animal origin has been developed in order to check the compliance with the Maximum Residue Levels (MRLs) set at a general value of 0.01 mg/kg by Commission Directive 2006/125/EC for infant foods. The main classes of organochlorine, organophosphorus and pyrethroid compounds have been considered, which are mainly fat soluble pesticides. The analytical procedure consists in the extraction of baby food samples by acetonitrile (ACN) followed by a clean up using C18 solid-phase extraction column eluted with ACN. The compounds were determined by gas chromatography-triple quadrupole mass spectrometry equipped with a Programmed Temperature Vaporizer (PTV) injection and a backflush system. In order to compensate for matrix effects PTV and matrix matched standard calibrations have been used. The method has been fully validated for 57 pesticides according to the Document SANCO/12571/2013. Accuracy and precision (repeatability) have been studied by recoveries at two spiking levels, the Limit of Quantitation (LOQ) (0.003-0.008 mg/kg) and 10 time greater (0.03-0.08 mg/kg), and the results were in the acceptable range of 70-120% with Relative Standards Deviations (RSD) ≤20%. Selectivity, linearity, LOQ and uncertainty of measurement were also determined for all the compounds. The method has been also applied for the analysis of 18 baby food animal origin samples, bought form the local market in Rome (Italy), and no pesticide in the scope of the method has been found above the MRL or the LOQ.

  1. Suitability of the charm HVS and a microbiological multiplate system for detection of residues in raw milk at EU maximum residue levels

    NARCIS (Netherlands)

    Nouws, J.F.M.; Egmond, van H.; Loeffen, G.; Schouten, J.; Keukens, H.; Smulders, I.; Stegeman, H.

    1999-01-01

    In this paper we assessed the suitability of the Charm HVS and a newly developed microbiological multiplate system as post-screening tests to confirm the presence of residues in raw milk at or near the maximum permissible residue level (MRL). The multiplate system is composed of Bacillus

  2. Removal of element mercury by medicine residue derived biochars in presence of various gas compositions

    International Nuclear Information System (INIS)

    Li, Guoliang; Shen, Boxiong; Li, Yongwang; Zhao, Bin; Wang, Fumei; He, Chuan; Wang, Yinyin; Zhang, Min

    2015-01-01

    Highlights: • Both physisorption and chemisorption of Hg 0 occurred on the surface of M6WN5. • Chemisorption process was an absolute predominant route for Hg 0 removal by M6WN5. • The effect of NO, H 2 O, SO 2 and O 2 on Hg 0 removal by M6WN5 was investigated. • M6WN5 demonstrated to be a promising Hg 0 sorbent in flue gas. - Abstract: Pyrolyzed biochars from an industrial medicinal residue waste were modified by microwave activation and NH 4 Cl impregnation. Mercury adsorption of different modified biochars was investigated in a quartz fixed-bed reactor. The results indicated that both physisorption and chemisorption of Hg 0 occurred on the surface of M6WN5 which was modified both microwave and 5 wt.% NH 4 Cl loading, and exothermic chemisorption process was a dominant route for Hg 0 removal. Microwave activation improved pore properties and NH 4 Cl impregnation introduced good active sites for biochars. The presence of NO and O 2 increased Hg 0 adsorption whereas H 2 O inhibited Hg 0 adsorption greatly. A converse effect of SO 2 was observed on Hg 0 removal, namely, low concentration of SO 2 promoted Hg 0 removal obviously whereas high concentration of SO 2 suppressed Hg 0 removal. The Hg 0 removal by M6WN5 was mainly due to the reaction of the C−Cl with Hg 0 to form HgCl 2 , and the active state of C−Cl * groups might be an intermediate group in this process. Thermodynamic analysis showed that mercury adsorption by the biochars was exothermic process and apparent adsorption energy was 43.3 kJ/mol in the range of chemisorption. In spite of low specific surface area, M6WN5 proved to be a promising Hg 0 sorbent in flue gas when compared with other sorbents

  3. Levels of organochlorine pesticide residues in butter samples collected from the Black Sea Region of Turkey.

    Science.gov (United States)

    Aksoy, Abdurrahman; Dervisoglu, Muhammed; Guvenc, Dilek; Gul, Osman; Yazici, Fehmi; Atmaca, Enes

    2013-01-01

    The aim of the present study was to evaluate the levels of 9 organochlorine compounds (aldrin, hexachlorobenzene, 2,4-DDE, 4,4-DDE, 2,4-DDT, 4,4-DDT, and α-, β-, and γ-HCH) in butter samples collected in the Eastern, Middle and Western Black Sea Regions of Turkey between October 2009 and June 2010. The liquid-liquid extraction method was used to extract the organochlorine compounds from the samples and the measurements were performed by using a gas chromatograph-electron capture detector system. DDT metabolites, aldrin, hexachlorobenzene (HCB), and α-, and γ-HCH were not detected in the samples but β-HCH was detected in 3 of a total of 88 samples. In the first period, only one sample from the West Black Sea Region was β-HCH positive (0.014 mg kg(-1)). The other β-HCH positive samples collected in Middle and West Black Sea Regions in the second period had a concentration of 0.066 and 0.019 mg kg(-1), respectively. All concentrations of the detected compounds exceeded the legal limits of 0.003 mg kg(-1) for β-HCH, as prescribed by the Turkish Food Codex, and therefore pose a potential health risk for consumers. The contamination detected is most likely due to the past usage of β-HCH in agriculture and its long term persistence in the environment. These results strongly suggest that further research should be focused on the detection of pesticide residues in agricultural areas across the nation.

  4. Thermal desorption-Gas chromatographic methodology for the determination of residual solvents in mesoporous silica.

    Science.gov (United States)

    Asfaw, Adissu Alemayehu; Wolfs, Kris; Schepdael, Ann Van; Adams, Erwin

    2017-06-02

    In this work, thermal desorption-gas chromatography-flame ionization detection (TD-GC-FID) was adapted to enable the determination of residual solvents (RS) in mesoporous silica (MPSi). MPSi is often utilized in various pharmaceutical formulations or drug delivery systems and the accurate determination of RS is an important part of pharmaceutical quality control. Seven commonly used solvents (methanol, ethanol, acetone, isopropanol, dichloromethane, tetrahydrofuran and hexafluoroisopropanol) were evaluated in combination with 3 types of MPSi having pore sizes of 2-3, 15 and 25nm. Validation results showed general recovery values >98% and good linearity over the concentration ranges studied. The limits of detection (LOD) and limits of quantification (LOQ) for the different solvents ranged from 0.03 to 0.08μg and from 0.1 to 0.2μg per tube, respectively. Verification of the accuracy of the TD method was investigated by using an alternative method based on complete dissolution of MPSi in hydrofluoric acid (HF) followed by full evaporation headspace-GC (HS-GC). The results obtained from both procedures were not statistically different (p>0.05) when applied to actual experimental drug samples consisting of itraconazole loaded on MPSi. Copyright © 2017 Elsevier B.V. All rights reserved.

  5. Prediction of Gas Chromatography-Mass Spectrometry Retention Times of Pesticide Residues by Chemometrics Methods

    Directory of Open Access Journals (Sweden)

    Elaheh Konoz

    2013-01-01

    Full Text Available A quantitative structure-retention relationships (QSRRs method is employed to predict the retention time of 300 pesticide residues in animal tissues separated by gas chromatography-mass spectroscopy (GC-MS. Firstly, a six-parameter QSRR model was developed by means of multiple linear regression. The six molecular descriptors that were considered to account for the effect of molecular structure on the retention time are number of nitrogen, Solvation connectivity index-chi 1, Balaban Y index, Moran autocorrelation-lag 2/weighted by atomic Sanderson electronegativity, total absolute charge, and radial distribution function-6.0/unweighted. A 6-7-1 back propagation artificial neural network (ANN was used to improve the accuracy of the constructed model. The standard error values of ANN model for training, test, and validation sets are 1.559, 1.517, and 1.249, respectively, which are less than those obtained reveals by multiple linear regressions model (2.402, 1.858, and 2.036, resp.. Results obtained the reliability and good predictability of nonlinear QSRR model to predict the retention time of pesticides.

  6. Computational fluid dynamics (CFD) analysis of the combustion process of a leather residuals gasification fuel gas: influence of fuel moisture content

    Energy Technology Data Exchange (ETDEWEB)

    Antonietti, Anderson Jose; Beskow, Arthur Bortolin; Silva, Cristiano Vitorino da [Universidade Regional Integrada do Alto Uruguai e das Missoes (URI), Erechim, RS (Brazil)], E-mails: arthur@uricer.edu.br, mlsperb@unisinos.br; Indrusiak, Maria Luiza Sperb [Universidade do Vale do Rio dos Sinos (UNISINOS), Sao Leopoldo, RS (Brazil)], E-mail: cristiano@uricer.edu.br

    2010-07-01

    This work presents a numerical study of the combustion process of leather residuals gasification gas, aiming the improvement of the process efficiency, considering different concentrations of water on the gas. The heating produced in this combustion process can be used to generation of thermal and/or electrical energy, for use at the leather industrial plant. However, the direct burning of this leather-residual-gas into the chambers is not straightforward. The alternative in development consists in processing this leather residuals by gasification or pyrolysis, separating the volatiles and products of incomplete combustion, for after use as fuel in a boiler. At these processes, different quantities of water can be used, resulting at different levels of moisture content in this fuel gas. This humidity can affect significantly the burning of this fuel, producing unburnt gases, as the carbon monoxide, or toxic gases as NOx, which must have their production minimized on the process, with the purpose of reducing the emission of pollutants to the atmosphere. Other environment-harmful-gases, remaining of the chemical treatment employed at leather manufacture, as cyanide, and hydrocarbons as toluene, must burn too, and the moisture content has influence on it. At this way, to increase understanding of the influence of moisture in the combustion process, it was made a numerical investigation study of reacting flow in the furnace, evaluating the temperature field, the chemical species concentration fields, flow mechanics and heat transfer at the process. The commercial CFD code CFX Ansys Inc. was used. Considering different moisture contents in the fuel used on the combustion process, with this study was possible to achieve the most efficient burning operation parameters, with improvement of combustion efficiency, and reduction of environmental harmful gases emissions. It was verified that the different moisture contents in the fuel gas demand different operation conditions

  7. Atmospheric Pressure Effect of Retained Gas in High Level Waste

    International Nuclear Information System (INIS)

    Weber, A.H.

    1999-01-01

    Isolated high level waste tanks in H-Area have unexplained changes in waste-level which have been attributed to environmental effects including pressure, temperature, and relative humidity. Previous studies at SRS have considered waste-level changes from causes not including the presence of gas in the salt cake. This study was undertaken to determine the effect of atmospheric pressure on gas in the salt cake and resultant changes in the supernate level of Tank 41H, and to model that effect if possible. A simple theory has been developed to account for changes in the supernate level in a high level waste tank containing damp salt cake as the response of trapped gases to changes in the ambient pressure. The gas is modeled as an ideal gas retained as bubbles within the interstitial spaces in the salt cake and distributed uniformly throughout the tank. The model does not account for consistent long term increases or decreases in the tank level. Any such trend in the tank level is attributed to changes in the liquid content in the tank (from condensation, evaporation, etc.) and is removed from the data prior to the void estimation. Short term fluctuations in the tank level are explained as the response of the entrained gas volume to changes in the ambient pressure. The model uses the response of the tank level to pressure changes to estimate an average void fraction for the time period of interest. This estimate of the void is then used to predict the expected level response. The theory was applied to three separate time periods of the level data for tank 41H as follows: (1) May 3, 1993 through August 3, 1993, (2) January 23, 1994 through April 21, 1994, and (3) June 4, 1994 through August 24, 1994. A strong correlation was found between fluctuations in the tank level and variations in the ambient pressure. This correlation is a clear marker of the presence of entrained gases in the tank. From model calculations, an average void fraction of 11 percent was estimated to

  8. NMR and Chemometric Characterization of Vacuum Residues and Vacuum Gas Oils from Crude Oils of Different Origin

    Directory of Open Access Journals (Sweden)

    Jelena Parlov Vuković

    2015-03-01

    Full Text Available NMR spectroscopy in combination with statistical methods was used to study vacuum residues and vacuum gas oils from 32 crude oils of different origin. Two chemometric metodes were applied. Firstly, principal component analysis on complete spectra was used to perform classification of samples and clear distinction between vacuum residues and vacuum light and heavy gas oils were obtained. To quantitatively predict the composition of asphaltenes, principal component regression models using areas of resonance signals spaned by 11 frequency bins of the 1H NMR spectra were build. The first 5 principal components accounted for more than 94 % of variations in the input data set and coefficient of determination for correlation between measured and predicted values was R2 = 0.7421. Although this value is not significant, it shows the underlying linear dependence in the data. Pseudo two-dimensional DOSY NMR experiments were used to assess the composition and structural properties of asphaltenes in a selected crude oil and its vacuum residue on the basis of their different hydrodynamic behavior and translational diffusion coefficients. DOSY spectra showed the presence of several asphaltene aggregates differing in size and interactions they formed. The obtained results have shown that NMR techniques in combination with chemometrics are very useful to analyze vacuum residues and vacuum gas oils. Furthermore, we expect that our ongoing investigation of asphaltenes from crude oils of different origin will elucidate in more details composition, structure and properties of these complex molecular systems.

  9. Characterisation of polycyclic aromatic hydrocarbons in flue gas and residues of a full scale fluidized bed combustor combusting non-hazardous industrial waste.

    Science.gov (United States)

    Van Caneghem, J; Vandecasteele, C

    2014-11-01

    This paper studies the fate of PAHs in full scale incinerators by analysing the concentration of the 16 EPA-PAHs in both the input waste and all the outputs of a full scale Fluidized Bed Combustor (FBC). Of the analysed waste inputs i.e. Waste Water Treatment (WWT) sludge, Refuse Derived Fuel (RDF) and Automotive Shredder Residue (ASR), RDF and ASR were the main PAH sources, with phenanthrene, fluoranthene and pyrene being the most important PAHs. In the flue gas sampled at the stack, naphthalene was the only predominant PAH, indicating that the PAHs in FBC's combustion gas were newly formed and did not remain from the input waste. Of the other outputs, the boiler and fly ash contained no detectable levels of PAHs, whereas the flue gas cleaning residue contained only low concentrations of naphthalene, probably adsorbed from the flue gas. The PAH fingerprint of the bottom ash corresponded rather well to the PAH fingerprint of the RDF and ASR, indicating that the PAHs in this output, in contrast to the other outputs, were mainly remainders from the PAHs in the waste inputs. A PAH mass balance showed that the total PAH input/output ratio of the FBC ranged from about 100 to about 2600 depending on the waste input composition and the obtained combustion conditions. In all cases, the FBC was clearly a net PAH sink. Copyright © 2014 Elsevier Ltd. All rights reserved.

  10. [Determination of propargite, tebuconazole and bromopropylate pesticide residues in Taiwan green jujubes by gas chromatography-tandem mass spectrometry].

    Science.gov (United States)

    Zhang, Qun; Liu, Chunhua; Wu, Nancun; Wu, Xiaofang; Li, Shuhuai

    2014-08-01

    An analytical method was established for the determination of propargite, tebuconazole and bromopropylate in Taiwan green jujubes (Zizyphus mauritiana Lam) by gas chromatography-tandem mass spectrometry (GC-MS/MS). The sample was extracted with acetonitrile from the Taiwan green jujubes after treated with a homogenizer. The organic phase was then separated from water phase by adding NaCl. The extract was further purified on a carbon/ NH2 cartridge with elution solvents of acetonitrile/toluene (3:1, v/v). Finally, the target analytes were separated by a capillary gas chromatographic column SLB-5MS (30 m x 0. 25 mm x 0. 25 μm). A tandem quadrupole mass spectrometer operated in either full scan mode or in MS/MS mode for multiple reaction monitoring (MRM) was used for the qualitative and quantitative analysis of the constituents, respectively. The results showed that the average recoveries of the three pesticides ranged from 75. 8% to 103. 6% with the RSDs of 1. 7%-9. 3% at the spiking levels from 0.01 mg/kg to 0. 50 mg/kg (n= 5). The calibration curves showed good linearity in the range of 0.01-0.50 mg/kg, with the determination coefficients over 0.99 (R2>0.99). The limits of quantification (LOQs) were 0.01 mg/kg for propargite, tebuconazole and bromopropylate in Taiwan green jujubes. The method is available for the determination of propargite, tebuconazole and bromopropylate pesticide residues in Taiwan green jujubes.

  11. Removal of element mercury by medicine residue derived biochars in presence of various gas compositions

    Energy Technology Data Exchange (ETDEWEB)

    Li, Guoliang [School of Energy and Environmental Engineering, Hebei University of Technology, Tianjin 300401 (China); College of Environmental Science and Engineering, Nankai University, Tianjin 300071 (China); Shen, Boxiong, E-mail: shenbx@nankai.edu.cn [School of Energy and Environmental Engineering, Hebei University of Technology, Tianjin 300401 (China); College of Environmental Science and Engineering, Nankai University, Tianjin 300071 (China); Li, Yongwang [College of Environmental Science and Engineering, Nankai University, Tianjin 300071 (China); Zhao, Bin [School of Chemical Engineering, Hebei University of Technology, Tianjin 300401 (China); Wang, Fumei; He, Chuan; Wang, Yinyin; Zhang, Min [College of Environmental Science and Engineering, Nankai University, Tianjin 300071 (China)

    2015-11-15

    Highlights: • Both physisorption and chemisorption of Hg{sup 0} occurred on the surface of M6WN5. • Chemisorption process was an absolute predominant route for Hg{sup 0} removal by M6WN5. • The effect of NO, H{sub 2}O, SO{sub 2} and O{sub 2} on Hg{sup 0} removal by M6WN5 was investigated. • M6WN5 demonstrated to be a promising Hg{sup 0} sorbent in flue gas. - Abstract: Pyrolyzed biochars from an industrial medicinal residue waste were modified by microwave activation and NH{sub 4}Cl impregnation. Mercury adsorption of different modified biochars was investigated in a quartz fixed-bed reactor. The results indicated that both physisorption and chemisorption of Hg{sup 0} occurred on the surface of M6WN5 which was modified both microwave and 5 wt.% NH{sub 4}Cl loading, and exothermic chemisorption process was a dominant route for Hg{sup 0} removal. Microwave activation improved pore properties and NH{sub 4}Cl impregnation introduced good active sites for biochars. The presence of NO and O{sub 2} increased Hg{sup 0} adsorption whereas H{sub 2}O inhibited Hg{sup 0} adsorption greatly. A converse effect of SO{sub 2} was observed on Hg{sup 0} removal, namely, low concentration of SO{sub 2} promoted Hg{sup 0} removal obviously whereas high concentration of SO{sub 2} suppressed Hg{sup 0} removal. The Hg{sup 0} removal by M6WN5 was mainly due to the reaction of the C−Cl with Hg{sup 0} to form HgCl{sub 2}, and the active state of C−Cl{sup *} groups might be an intermediate group in this process. Thermodynamic analysis showed that mercury adsorption by the biochars was exothermic process and apparent adsorption energy was 43.3 kJ/mol in the range of chemisorption. In spite of low specific surface area, M6WN5 proved to be a promising Hg{sup 0} sorbent in flue gas when compared with other sorbents.

  12. Determination of cyflumetofen residue in water, soil, and fruits by modified quick, easy, cheap, effective, rugged, and safe method coupled to gas chromatography/tandem mass spectrometry.

    Science.gov (United States)

    Li, Minmin; Liu, Xingang; Dong, Fengshou; Xu, Jun; Qin, Dongmei; Zheng, Yongquan

    2012-10-01

    A new, highly sensitive, and selective method was developed for the determination of the cyflumetofen residue in water, soil, and fruits by using gas chromatography quadruple mass spectrometry. The target compound was extracted using acetonitrile and then cleaned up using dispersive solid-phase extraction with primary and secondary amine and graphitized carbon black, and optionally by a freezing-out cleanup step. The matrix-matched standards gave satisfactory recoveries and relative standard deviation values in different matrices at three fortified levels (0.05, 0.5, and 1.0 mg kg(-1) ). The overall average recoveries for this method in water, soil, and all fruits matrix at three fortified levels ranged from 76.3 to 101.5% with relative standard deviations in the range of 1.2-11.8% (n = 5). The calculated limits of detection and quantification were typically below 0.005 and 0.015 μg kg(-1), which were much lower than the maximum residue levels established by Japanese Positive List. This study provides a theoretical basis for China to draw up maximum residue level and analytical method for cyflumetofen acaricide in different fruits. © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  13. Effect of the Leveling Conditions on Residual Stress Evolution of Hot Rolled High Strength Steels for Cold Forming

    Science.gov (United States)

    Park, Keecheol; Oh, Kyungsuk

    2017-09-01

    In order to investigate the effect of leveling conditions on residual stress evolution during the leveling process of hot rolled high strength steels, the in-plane residual stresses of sheet processed under controlled conditions at skin-pass mill and levelers were measured by cutting method. The residual stress was localized near the edge of sheet. As the thickness of sheet was increased, the residual stress occurred region was expanded. The magnitude of residual stress within the sheet was reduced as increasing the deformation occurred during the leveling process. But the residual stress itself was not removed completely. The magnitude of camber occurred at cut plate was able to be predicted by the residual stress distribution. A numerical algorithm was developed for analysing the effect of leveling conditions on residual stress. It was able to implement the effect of plastic deformation in leveling, tension, work roll bending, and initial state of sheet (residual stress and curl distribution). The validity of simulated results was verified from comparison with the experimentally measured residual stress and curl in a sheet.

  14. Greenhouse gas reductions through enhanced use of residues in the life cycle of Malaysian palm oil derived biodiesel

    DEFF Research Database (Denmark)

    Hansen, Sune Balle; Olsen, Stig Irving; Ujang, Zaini

    2012-01-01

    This study identifies the potential greenhouse gas (GHG) reductions, which can be achieved by optimizing the use of residues in the life cycle of palm oil derived biodiesel. This is done through compilation of data on existing and prospective treatment technologies as well as practical experiments...... on methane potentials from empty fruit bunches. Methane capture from the anaerobic digestion of palm oil mill effluent was found to result in the highest GHG reductions. Among the solid residues, energy extraction from shells was found to constitute the biggest GHG savings per ton of residue, whereas energy...... extraction from empty fruit bunches was found to be the most significant in the biodiesel production life cycle. All the studied waste treatment technologies performed significantly better than the conventional practices and with dedicated efforts of optimized use in the palm oil industry, the production...

  15. Lead and PCB's in canvasback ducks: Relationship between enzyme levels and residues in blood

    Science.gov (United States)

    Dieter, M.P.; Perry, M.C.; Mulhern, B.M.

    1976-01-01

    Blood samples were taken for two successive years from canvasback ducks trapped in the Chesapeake Bay. The first winter (1972?1973) five plasma enzymes known to respond to organochlorine poisoning were examined. Abnormal enzyme elevations suggested that 20% of the population sampled (23/115 ducks) might contain organochlorine contaminants, but no residue analyses were performed. The second winter (1974) two of the same enzymes, aspartate aminotransferase and lactate dehydrogenase, and a third enzyme known to be specifically inhibited by lead, delta-aminolevulinic acid dehydratase, were assayed in 95 blood samples. Blood residues of organochlorine compounds and of lead were determined in representative samples, and the correlations between residue levels and enzyme changes were examined. The enzyme bioassays in 1974 indicated that lead was a more prevalent environmental contaminant than organochlorine compounds in canvasback ducks; 17% of the blood samples had less than one-half of the normal delta-aminolevulinic acid dehydratase activity, but only 11% exhibited abnormal aspartate aminotransferase or lactate dehydrogenase activities. These findings were confirmed by residue analyses that demonstrated lead concentrations four times higher than background levels, but only relatively low organochlorine concentrations. There was a highly significant inverse correlation between delta-aminolevulinic acid dehydratase activity and blood lead concentrations (Pheme synthesis and is regarded as detrimental in humans.

  16. Multi-level learning: improving the prediction of protein, domain and residue interactions by allowing information flow between levels.

    Science.gov (United States)

    Yip, Kevin Y; Kim, Philip M; McDermott, Drew; Gerstein, Mark

    2009-08-05

    Proteins interact through specific binding interfaces that contain many residues in domains. Protein interactions thus occur on three different levels of a concept hierarchy: whole-proteins, domains, and residues. Each level offers a distinct and complementary set of features for computationally predicting interactions, including functional genomic features of whole proteins, evolutionary features of domain families and physical-chemical features of individual residues. The predictions at each level could benefit from using the features at all three levels. However, it is not trivial as the features are provided at different granularity. To link up the predictions at the three levels, we propose a multi-level machine-learning framework that allows for explicit information flow between the levels. We demonstrate, using representative yeast interaction networks, that our algorithm is able to utilize complementary feature sets to make more accurate predictions at the three levels than when the three problems are approached independently. To facilitate application of our multi-level learning framework, we discuss three key aspects of multi-level learning and the corresponding design choices that we have made in the implementation of a concrete learning algorithm. 1) Architecture of information flow: we show the greater flexibility of bidirectional flow over independent levels and unidirectional flow; 2) Coupling mechanism of the different levels: We show how this can be accomplished via augmenting the training sets at each level, and discuss the prevention of error propagation between different levels by means of soft coupling; 3) Sparseness of data: We show that the multi-level framework compounds data sparsity issues, and discuss how this can be dealt with by building local models in information-rich parts of the data. Our proof-of-concept learning algorithm demonstrates the advantage of combining levels, and opens up opportunities for further research. The software

  17. Multi-level learning: improving the prediction of protein, domain and residue interactions by allowing information flow between levels

    Directory of Open Access Journals (Sweden)

    McDermott Drew

    2009-08-01

    Full Text Available Abstract Background Proteins interact through specific binding interfaces that contain many residues in domains. Protein interactions thus occur on three different levels of a concept hierarchy: whole-proteins, domains, and residues. Each level offers a distinct and complementary set of features for computationally predicting interactions, including functional genomic features of whole proteins, evolutionary features of domain families and physical-chemical features of individual residues. The predictions at each level could benefit from using the features at all three levels. However, it is not trivial as the features are provided at different granularity. Results To link up the predictions at the three levels, we propose a multi-level machine-learning framework that allows for explicit information flow between the levels. We demonstrate, using representative yeast interaction networks, that our algorithm is able to utilize complementary feature sets to make more accurate predictions at the three levels than when the three problems are approached independently. To facilitate application of our multi-level learning framework, we discuss three key aspects of multi-level learning and the corresponding design choices that we have made in the implementation of a concrete learning algorithm. 1 Architecture of information flow: we show the greater flexibility of bidirectional flow over independent levels and unidirectional flow; 2 Coupling mechanism of the different levels: We show how this can be accomplished via augmenting the training sets at each level, and discuss the prevention of error propagation between different levels by means of soft coupling; 3 Sparseness of data: We show that the multi-level framework compounds data sparsity issues, and discuss how this can be dealt with by building local models in information-rich parts of the data. Our proof-of-concept learning algorithm demonstrates the advantage of combining levels, and opens up

  18. the effect of varying levels of supplements on degradability, gas ...

    African Journals Online (AJOL)

    ansi

    stages, mixed with varying types and levels of roughage and fermented for 72 h in vitro, using the gas ... 676.6 and 685.0 g/kg, respectively) between ELP rations. The roughages had similar but lower degradability in LLP rations. (means 633.4, 632.6 and 631.1 g/kg for MM, MD and GH, ...... Tilley, J.M.A. & Terry, R.A., 1963.

  19. A residue level protein-protein interaction model in electrolyte solutions

    Science.gov (United States)

    Song, Xueyu

    2014-03-01

    The osmotic second virial coefficients B2 are directly related to the solubility of protein molecules in electrolyte solutions and can be useful to narrow down the search parameter space of protein crystallization conditions. Using a residue level model of protein-protein interaction in electrolyte solutions B2 of bovine pancreatic trypsin inhibitor and lysozyme in various solution conditions such as salt concentration, pH and temperature are calculated using an extended Fast Multipole Methods in combination with the boundary element formulation. Overall, the calculated B2 are well correlated with the experimental observations for various solution conditions. In combination with our previous work on the binding affinity calculations of protein complexes it is demonstrated that our residue level model can be used as a reliable model to describe protein-protein interaction in solutions.

  20. Analysis of residual stress in metal-inert-gas-welded Al-2024 using neutron and synchrotron X-ray diffraction

    International Nuclear Information System (INIS)

    Ganguly, S.; Stelmukh, V.; Edwards, L.; Fitzpatrick, M.E.

    2008-01-01

    A combination of neutron and synchrotron X-ray diffraction was used to measure and map the full three-dimensional state of residual stress across the cross-section in coupon samples of metal-inert-gas (MIG)-welded 2024 aluminium alloy. Samples were analysed both as-welded and following a post-welding skim which served to remove the weld flash and reduce the plate thickness. The profile of the residual stress and its evolution following skimming has been accurately characterized. The longitudinal direction shows the highest residual stress, approaching 300 MPa in tension. The skimming treatment did not change the peak stress, but the overall profile of stress was altered: this is slightly unexpected as machining away stressed material would generally be expected to reduce the peak residual stress. The results are discussed in terms of the generation of stress during welding and its evolution during skimming. Finally a comparison is made with the stress generated in the as-welded and skimmed conditions of a variable polarity plasma arc (VPPA)-welded specimen of similar dimensions, to show the effects of different weld processes on the residual stress generated. The stress measurement in the VPPA sample was carried out under near identical experimental conditions

  1. Gas chromatographic determination of residual hydrazine and morpholine in boiler feed water and steam condensates

    International Nuclear Information System (INIS)

    Vatsala, S.; Bansal, V.; Tuli, D.K.; Rai, M.M.; Jain, S.K.; Srivastava, S.P.; Bhatnagar, A.K.

    1994-01-01

    Hydrazine, an oxygen scavenger in boiler water, was derivatised to the corresponding acetone azine and determined at the ng ml -1 level by gas chromatography. Morpholine, a corrosion inhibitor used in steam boilers, was estimated either directly (if >2.0 μg ml -1 ) or by quantitative preconcentration (0.1 ng-2.0 μg ml -1 ). To obtain symmetrical peaks for these amines, the column packing was coated with KOH. Use of a nitrogen-specific detector improved accuracy of estimation of hydrazine and morpholine, giving a RSD of 1.9-3.6%. Chromatographic analysis of these amines in boiler feed water and steam condensate samples collected from boilers servicing a pertroleum refinery is described. Environmental safety regulations calls for monitoring of hydrazine and the methods developed can easily be adapted for this purpose. (orig.)

  2. Correlation between residual level of DNA double-strand breaks and the radiosensitivity of cancer cells

    International Nuclear Information System (INIS)

    Sun Jianxiang; Sun Weijian; Sui Jianli; Zhou Pingkun

    2008-01-01

    Objective: To understand the variation of the DNA double-strand break rejoining capacity among different cultured cancer cell lines and the primary cancer cells from brain cancer patients, and to explore the predictor of radiotherapy responses of cancers. Methods: DNA double-strand breaks (DSBs) were induced by 60 Co γ-irradiation. Pulsed-field gel electrophoresis was used to analyze the initial production and rejoining of DNA DSBs. Radiosensitivity was determined by in vitro assay of clonogenic-forming capacity. Results: A wide variation of radiosensitivity, e.g. the survival parameter of Do varied from 0.65 to 2.15 Gy, was displayed among the eight cell lines derived from different type of cancers. Although differential level of initial DNA DSBs induced by 20 Gy γ-rays was observed among various cell lines, it was not correlated with the radiosensitivity. The deficiency of DNA DSB rejoining in radiosensitive cell lines was shown either in the early rapid-rejoining phase (SX-10 cells) or in the late slow-rejoining phase (A2780 cells). A significant relationship was observed between the residual level of DNA DSBs measured at 2 h post-20 Gy irradiation and the cellular radiosensitivity (D 0 or SF 2 ). The kinetic curves of rejoining DNA DSBs in the primary human brain tumor cells indicated a variation on DSB rejoining capacity among different individual tumor. The residual level of DNA DSBs after 2 h of rejoining post 20 Gy irradiation in primary human brain tumor cells is compatible to the results obtained in vitro culture cancer cell lines. Conclusions: The residual level of DNA DSBs is correlated with radioresistance of cancer cells, and the residual DNA damage is a useful parameter in predicting the response of tumor tissue to radiotherapy. (authors)

  3. (210)Pb content in natural gas pipeline residues ("black-powder") and its correlation with the chemical composition.

    Science.gov (United States)

    Godoy, José Marcus; Carvalho, Franciane; Cordilha, Aloisio; Matta, Luiz Ernesto; Godoy, Maria Luiza

    2005-01-01

    The present work was carried out to assess the (210)Pb content in "black-powder" found in pigging operations on gas pipelines in Brazil, in particular, on the Campos Basin gas pipeline. Additionally, the chemical composition of such deposits was determined and an eventual correlation with (210)Pb concentration evaluated. Typical "black-powder" generated in the natural gas pipeline from Campos Basin oilfield contains mainly iron oxide ( approximately 81%) and residual organic matter ( approximately 9%). The (210)Pb content ranges from 4.9 to 0.04k Bqkg(-1) and seems to be inversely correlated with the distance to the platforms. On the other hand, (226)Ra concentration is higher on the pipeline branch between the platform and the onshore installations. (228)Ra was only observed in few samples, in particular, in the samples with the highest (226)Ra content.

  4. Quantifying and reporting greenhouse gas emissions at local level

    Directory of Open Access Journals (Sweden)

    Sόwka Izabela

    2017-01-01

    Full Text Available Cities as global centers of consumption and production often are a significant and growing source of greenhouse gas (GHG emissions. At the same time, local authorities are increasingly taking action on climate change by focusing on reducing GHG emissions and efficiency improvement opportunities. To assess and reduce the overall greenhouse gas emission level from an urban area, it is necessary to identify all the activities and processes which generate these emissions. GHG inventory gives an opportunity to get wider knowledge for city’s community about spatial emission processes and emissions contribution of key sources categories at the local scale. Inventory is being used for decision-making purposes and strategic planning in emission reduction policy. The goal of this paper was to clarify the major methodological challenges of GHG monitoring at the urban level. The paper is based on the discussion of different methods and approaches to assessing GHG emissions at the local level. It is presented sectoral GHGs emission trends in selected urban areas and compared CO2 emission level in different countries and metropolises and variable European cities guidance. The study determines the inventory tools of GHGs emission taking into account the characteristics of main sources at local levels.

  5. Cyanide residue levels in extracted honey, comb honey and wax cappings.

    Science.gov (United States)

    Ihnat, M; Nelson, D L

    1979-01-01

    Cyanide (CN) residue levels were determined in samples of extracted honey, comb honey and was cappings at 1 hr, 24 hr, and 48 hr intervals after destroying the bees in honey bee colonies with normal (ca. 8.5 g) and twice normal (ca. 17 g) doses of CyanogasR A-dust. Applications of CyanogasR A-dust, administered by means of a dust pump at normal and twice normal doses, gave an average residue of 0.01 and 0.04 microgram CN/g of extracted honey, 0.01 and 0.02 microgram CN/g of comb honey and 0.04 and 0.06 microgram CN/g of wax cappings, respectively. When the CyanogasR A-dust (ca. 17 g) was placed on a tray and placed on the bottom board of the hive, the average residue levels for extracted honey, comb honey and wax cappings were less than 0.004, 0.01 and 0.02 microgram CN/g, respectively. Random honey samples from beekeepers, who used CyanogasR to destroy bees, had a median level of 0.031 microgram CN/g, whereas honey from a packing plant and other commercial samples contained less than 0.004--0.026, median less than 0.004 microgram CN/g. Based on residue data from this study, the temporary registration for CyanogasR, to kill honey bees after crop removal, was revised to a full registration in May 1977.

  6. RESIDUAL GAS MOTIONS IN THE INTRACLUSTER MEDIUM AND BIAS IN HYDROSTATIC MEASUREMENTS OF MASS PROFILES OF CLUSTERS

    International Nuclear Information System (INIS)

    Lau, Erwin T.; Kravtsov, Andrey V.; Nagai, Daisuke

    2009-01-01

    We present analysis of bulk and random gas motions in the intracluster medium using high-resolution Eulerian cosmological simulations of 16 simulated clusters, including both very relaxed and unrelaxed systems and spanning a virial mass range of 5 x 10 13 - 2 x 10 15 h -1 M-odot. We investigate effects of the residual subsonic gas motions on the hydrostatic estimates of mass profiles and concentrations of galaxy clusters. In agreement with previous studies, we find that the gas motions contribute up to ∼5%-15% of the total pressure support in relaxed clusters with contribution increasing with the cluster-centric radius. The fractional pressure support is higher in unrelaxed systems. This contribution would not be accounted for in hydrostatic estimates of the total mass profile and would lead to systematic underestimate of mass. We demonstrate that total mass can be recovered accurately if pressure due to gas motions measured in simulations is explicitly taken into account in the equation of hydrostatic equilibrium. Given that the underestimate of mass is increasing at larger radii, where gas is less relaxed and contribution of gas motions to pressure is larger, the total density profile derived from hydrostatic analysis is more concentrated than the true profile. This may at least partially explain some high values of concentrations of clusters estimated from hydrostatic analysis of X-ray data.

  7. Soil gas surveying at low-level radioactive waste sites

    International Nuclear Information System (INIS)

    Crockett, A.B.; Moor, K.S.; Hull, L.C.

    1990-01-01

    Soil gas sampling is a useful screening technique for determining whether volatile organic compounds are present at low-level radioactive waste burial sites. The technique was used at several DOE sites during the DOE Environmental Survey to determine the presence and extent of volatile organic compound contamination. The advantages of the soil gas sampling are that near real time data can be obtained, no excavation is required, safety concerns are relatively minor, costs are relatively low, and large amounts of data can be obtained rapidly on the contaminants that may pose the greatest threat to groundwater resources. The disadvantages are that the data are difficult to interpret and relate to soil concentrations and environmental standards. This paper discusses the experiences of INEL sampling and analysis personnel, the advantages and disadvantages of the technique, and makes recommendations for improving the sampling and procedures. 11 refs., 8 figs., 3 tabs

  8. Light Path Model of Fiber Optic Liquid Level Sensor Considering Residual Liquid Film on the Wall

    Directory of Open Access Journals (Sweden)

    Zhijun Zhang

    2015-01-01

    Full Text Available The working principle of the refractive-type fiber optic liquid level sensor is analyzed in detail based on the light refraction principle. The optic path models are developed in consideration of common simplification and the residual liquid film on the glass tube wall. The calculating formulae for the model are derived, constraint conditions are obtained, influencing factors are discussed, and the scopes and skills of application are analyzed through instance simulations. The research results are useful in directing the correct usage of the fiber optic liquid level sensor, especially in special cases, such as those involving viscous liquid in the glass tube monitoring.

  9. Residual energy level based clustering routing protocol for wireless sensor networks

    Science.gov (United States)

    Yuan, Xu; Zhong, Fangming; Chen, Zhikui; Yang, Deli

    2015-12-01

    The wireless sensor networks, which nodes prone to premature death, with unbalanced energy consumption and a short life time, influenced the promotion and application of this technology in internet of things in agriculture. This paper proposes a clustering routing protocol based on the residual energy level (RELCP). RELCP includes three stages: the selection of cluster head, establishment of cluster and data transmission. RELCP considers the remaining energy level and distance to base station, while election of cluster head nodes and data transmitting. Simulation results demonstrate that the protocol can efficiently balance the energy dissipation of all nodes, and prolong the network lifetime.

  10. Validation of QuEChERS based method for determination of fenitrothion residues in tomatoes by gas chromatography-flame photometric detector: Decline pattern and risk assessment.

    Science.gov (United States)

    Malhat, Farag; Boulangé, Julien; Abdelraheem, Ehab; Abd Allah, Osama; Abd El-Hamid, Rania; Abd El-Salam, Shokr

    2017-08-15

    A simple and rapid gas chromatography with flame photometric detector (GC-FPD) determination method was developed to detect residue levels and investigate the dissipation pattern and safe use of fenitrothion in tomatoes. A modified quick, easy, cheap, effective, rugged, and safe (QuEChERS) using an ethyl acetate-based extraction, followed by a dispersive solid-phase extraction (d-SPE) with primary-secondary amine (PSA) and graphite carbon black (GCB) for clean up, was applied prior to GC-FPD analysis. The method showed satisfactory linearity, recovery and precision. The limits of detection (LOD) and quantification (LOQ) were 0.005 and 0.01mg/kg, respectively. The residue levels of fenitrothion were best described by first order kinetics with a half-life of 2.2days in tomatoes. The potential health risks posed by fenitrothion were not significant, based on supervised residue trial data. The current findings could provide guidance for safe and reasonable use of fenitrothion in tomatoes and prevent health problems to consumers. Copyright © 2017 Elsevier Ltd. All rights reserved.

  11. Residual mitochondrial transmembrane potential decreases unsaturated fatty acid level in sake yeast during alcoholic fermentation

    Directory of Open Access Journals (Sweden)

    Kazutaka Sawada

    2016-01-01

    Full Text Available Oxygen, a key nutrient in alcoholic fermentation, is rapidly depleted during this process. Several pathways of oxygen utilization have been reported in the yeast Saccharomyces cerevisiae during alcoholic fermentation, namely synthesis of unsaturated fatty acid, sterols and heme, and the mitochondrial electron transport chain. However, the interaction between these pathways has not been investigated. In this study, we showed that the major proportion of unsaturated fatty acids of ester-linked lipids in sake fermentation mash is derived from the sake yeast rather than from rice or koji (rice fermented with Aspergillus. Additionally, during alcoholic fermentation, inhibition of the residual mitochondrial activity of sake yeast increases the levels of unsaturated fatty acids of ester-linked lipids. These findings indicate that the residual activity of the mitochondrial electron transport chain reduces molecular oxygen levels and decreases the synthesis of unsaturated fatty acids, thereby increasing the synthesis of estery flavors by sake yeast. This is the first report of a novel link between residual mitochondrial transmembrane potential and the synthesis of unsaturated fatty acids by the brewery yeast during alcoholic fermentation.

  12. Residual mitochondrial transmembrane potential decreases unsaturated fatty acid level in sake yeast during alcoholic fermentation

    Science.gov (United States)

    Sawada, Kazutaka

    2016-01-01

    Oxygen, a key nutrient in alcoholic fermentation, is rapidly depleted during this process. Several pathways of oxygen utilization have been reported in the yeast Saccharomyces cerevisiae during alcoholic fermentation, namely synthesis of unsaturated fatty acid, sterols and heme, and the mitochondrial electron transport chain. However, the interaction between these pathways has not been investigated. In this study, we showed that the major proportion of unsaturated fatty acids of ester-linked lipids in sake fermentation mash is derived from the sake yeast rather than from rice or koji (rice fermented with Aspergillus). Additionally, during alcoholic fermentation, inhibition of the residual mitochondrial activity of sake yeast increases the levels of unsaturated fatty acids of ester-linked lipids. These findings indicate that the residual activity of the mitochondrial electron transport chain reduces molecular oxygen levels and decreases the synthesis of unsaturated fatty acids, thereby increasing the synthesis of estery flavors by sake yeast. This is the first report of a novel link between residual mitochondrial transmembrane potential and the synthesis of unsaturated fatty acids by the brewery yeast during alcoholic fermentation. PMID:26839744

  13. Determination of pesticide residues (> 0.5 microg/L) in soft drinks and sports drinks by gas chromatography with mass spectrometry: collaborative study.

    Science.gov (United States)

    Miller, Kathleen D; Milne, Paul

    2008-01-01

    A collaborative study was conducted on a method for the measurement of 19 low-level pesticide residues in soft drinks and sports drinks by gas chromatography with mass spectrometry (GC/MS). The pesticide residues determined were 2,4'-dichlorodiphenyldichloroethylene (2,4'-DDE); 2,4'-dichlorodiphenyldichloroethane (2,4'-DDD); 4,4'-dichlorodiphenyldichloroethylene (4,4'-DDE); 2,4'-dichlorodiphenyltrichloroethane (2,4'-DDT); 4,4'-dichlorodiphenyltrichloroethane (4,4'-DDT); 4,4'-dichlorodiphenyldichloroethane (4,4'-DDD); alpha-endosulfan; endosulfan-sulfate; dieldrin; aldrin; ethion; chlorpyrifos; beta-endosulfan; malathion; methyl-parathion; alpha-hexachlorocyclohexane (alpha-HCH); beta-HCH; delta-HCH; and gamma-HCH. Blind fortification solutions containing 4 different levels of pesticide residues (0, 0.1, 0.5, and 1.0 microg/L) were provided to 8 collaborating laboratories who used them to create test samples in 6 matrixes (also provided): 2 colas, a diet cola, a clear lemon-lime soft drink, an orange soft drink, and a sports drink. Reproducibility (RSDR) for all 19 pesticide residues in all matrixes ranged from 7 to 151% at the 0.1 microg/L level, 11 to 121% at 0.5 microg/L, and 14 to 67% at 1.0 microg/L. Repeatability (RSDr), applicable to the diet cola and the sports drink, ranged from 1 to 76% for the 19 pesticide residues at the 0.1 microg/L level, 9 to 38% at 0.5 microg/L, and 9 to 38% at 1.0 microg/L. Recoveries for the 19 pesticide residues in all matrixes ranged from 77 to 645% at the 0.1 microg/L level, 60 to 231% at 0.5 microg/L, and 61 to 146% at 1.0 microg/L. It is recommended that the method be accepted by AOAC as Official First Action with a limit of quantification (LOQ) equal to 0.5 microg/L for 4,4'-DDT; 2,4'-DDT; 2,4'-DDD; 4,4'-DDE; 4,4'-DDD; 2,4'-DDE; aldrin; dieldrin; alpha-endosulfan; endosulfan-sulfate; chlorpyrifos; and ethion, and an LOQ equal to 1.0 microg/L for beta-endosulfan; alpha-HCH; beta-HCH; delta-HCH; gamma-HCH; methyl-parathion; and

  14. Residues levels of organochlorine pesticide in cow's milk from industrial farms in Hidalgo, Mexico.

    Science.gov (United States)

    Gutierrez, Rey; Ortiz, Rutilio; Vega, Salvador; Schettino, Beatriz; Ramirez, Maria L; Perez, Jose J

    2013-01-01

    A survey was carried out from 2008 to 2010 to determine the concentrations of 16 organochlorine pesticide residues (OPRs) from Tizayuca, Hidalgo, Mexico. Organochlorine residue determinations were made from milk fat, using chromatographic cleanup and analysis by gas chromatography with an electron capture detector. The OPR concentrations found were from below the detection limit (DL) to 0.91 ng g(-1) in 2008, DL to 0.38 ng g(-1) in 2009 and DL to 0.59 ng g(-1) in 2010. In general concentrations of organochlorine pesticides were higher in the wet season (3.37 ng g(-1) and 4.79 ng g(-1)) than the dry season (1.92 ng g(-1) and 2.71 ng g(-1)) for 2009 and 2010, due to control of pests in the pasture and sheds. According to Codex Alimentarius regulations, individual pesticides did not exceed the permissible limits, which for example were 10 μg kg(-)1 for alpha hexachlorocyclohexane (HCH) and endosulfan I, 20 μg kg(-1) for p,p'-DDT, and 6 μg kg(-1) for dieldrin, endrin and heptachlor. A reduction of organochlorine pesticide concentrations in cow's milk was noted, indicating that the Mexican government has achieved reduction or elimination of some organochlorine pesticides in response to global agreements on persistent organic pollutants.

  15. ELISA validation and determination of cut-off level for chloramphenicol residues in honey

    Directory of Open Access Journals (Sweden)

    Biernacki Bogumił

    2015-09-01

    Full Text Available An analytical validation of a screening ELISA for detection of chloramphenicol (CAP in honey was conducted according to the Commission Decision 2002/657/EC and Guidelines for the Validation of Screening Methods for Residues of Veterinary Medicines. The analyte was extracted from honey with a water and ethyl acetate mixture, and CAP concentrations were measured photometrically at 450 nm. The recovery rate of the analyte from spiked samples was 79%. The cut-off level of CAP in honey as the minimum recovery (0.17 units was established. Detection capability (CCβ was fixed at 0.25 μg kg−1. No relevant interferences between matrix effects and structurally related substances including florfenicol and thiamphenicol were observed. The ELISA method should be useful for determination of CAP residues in honey monitoring.

  16. A comparative study of allowable pesticide residue levels on produce in the United States

    Directory of Open Access Journals (Sweden)

    Neff Roni A

    2012-01-01

    Full Text Available Abstract Background The U.S. imports a substantial and increasing portion of its fruits and vegetables. The U.S. Food and Drug Administration currently inspects less than one percent of import shipments. While countries exporting to the U.S. are expected to comply with U.S. tolerances, including allowable pesticide residue levels, there is a low rate of import inspections and few other incentives for compliance. Methods This analysis estimates the quantity of excess pesticide residue that could enter the U.S. if exporters followed originating country requirements but not U.S. pesticide tolerances, for the top 20 imported produce items based on quantities imported and U.S. consumption levels. Pesticide health effects data are also shown. Results The model estimates that for the identified items, 120 439 kg of pesticides in excess of U.S. tolerances could potentially be imported to the U.S., in cases where U.S. regulations are more protective than those of originating countries. This figure is in addition to residues allowed on domestic produce. In the modeling, the top produce item, market, and pesticide of concern were oranges, Chile, and Zeta-Cypermethrin. Pesticides in this review are associated with health effects on 13 body systems, and some are associated with carcinogenic effects. Conclusions There is a critical information gap regarding pesticide residues on produce imported to the U.S. Without a more thorough sampling program, it is not possible accurately to characterize risks introduced by produce importation. The scenario presented herein relies on assumptions, and should be considered illustrative. The analysis highlights the need for additional investigation and resources for monitoring, enforcement, and other interventions, to improve import food safety and reduce pesticide exposures in originating countries.

  17. Direct gas-solid carbonation of serpentinite residues in the absence and presence of water vapor: a feasibility study for carbon dioxide sequestration.

    Science.gov (United States)

    Veetil, Sanoopkumar Puthiya; Pasquier, Louis-César; Blais, Jean-François; Cecchi, Emmanuelle; Kentish, Sandra; Mercier, Guy

    2015-09-01

    Mineral carbonation of serpentinite mining residue offers an environmentally secure and permanent storage of carbon dioxide. The strategy of using readily available mining residue for the direct treatment of flue gas could improve the energy demand and economics of CO2 sequestration by avoiding the mineral extraction and separate CO2 capture steps. The present is a laboratory scale study to assess the possibility of CO2 fixation in serpentinite mining residues via direct gas-solid reaction. The degree of carbonation is measured both in the absence and presence of water vapor in a batch reactor. The gas used is a simulated gas mixture reproducing an average cement flue gas CO2 composition of 18 vol.% CO2. The reaction parameters considered are temperature, total gas pressure, time, and concentration of water vapor. In the absence of water vapor, the gas-solid carbonation of serpentinite mining residues is negligible, but the residues removed CO2 from the feed gas possibly due to reversible adsorption. The presence of small amount of water vapor enhances the gas-solid carbonation, but the measured rates are too low for practical application. The maximum CO2 fixation obtained is 0.07 g CO2 when reacting 1 g of residue at 200 °C and 25 barg (pCO2 ≈ 4.7) in a gas mixture containing 18 vol.% CO2 and 10 vol.% water vapor in 1 h. The fixation is likely surface limited and restricted due to poor gas-solid interaction. It was identified that both the relative humidity and carbon dioxide-water vapor ratio have a role in CO2 fixation regardless of the percentage of water vapor.

  18. Dietary exposure to pesticide residues from commodities alleged to contain the highest contamination levels.

    Science.gov (United States)

    Winter, Carl K; Katz, Josh M

    2011-01-01

    Probabilistic techniques were used to characterize dietary exposure of consumers to pesticides found in twelve commodities implicated as having the greatest potential for pesticide residue contamination by a United States-based environmental advocacy group. Estimates of exposures were derived for the ten most frequently detected pesticide residues on each of the twelve commodities based upon residue findings from the United States Department of Agriculture's Pesticide Data Program. All pesticide exposure estimates were well below established chronic reference doses (RfDs). Only one of the 120 exposure estimates exceeded 1% of the RfD (methamidophos on bell peppers at 2% of the RfD), and only seven exposure estimates (5.8 percent) exceeded 0.1% of the RfD. Three quarters of the pesticide/commodity combinations demonstrated exposure estimates below 0.01% of the RfD (corresponding to exposures one million times below chronic No Observable Adverse Effect Levels from animal toxicology studies), and 40.8% had exposure estimates below 0.001% of the RfD. It is concluded that (1) exposures to the most commonly detected pesticides on the twelve commodities pose negligible risks to consumers, (2) substitution of organic forms of the twelve commodities for conventional forms does not result in any appreciable reduction of consumer risks, and (3) the methodology used by the environmental advocacy group to rank commodities with respect to pesticide risks lacks scientific credibility.

  19. A stochastic logical system approach to model and optimal control of cyclic variation of residual gas fraction in combustion engines

    International Nuclear Information System (INIS)

    Wu, Yuhu; Kumar, Madan; Shen, Tielong

    2016-01-01

    Highlights: • An in-cylinder pressure based measuring method for the RGF is derived. • A stochastic logical dynamical model is proposed to represent the transient behavior of the RGF. • The receding horizon controller is designed to reduce the variance of the RGF. • The effectiveness of the proposed model and control approach is validated by the experimental evidence. - Abstract: In four stroke internal combustion engines, residual gas from the previous cycle is an important factor influencing the combustion quality of the current cycle, and the residual gas fraction (RGF) is a popular index to monitor the influence of residual gas. This paper investigates the cycle-to-cycle transient behavior of the RGF in the view of systems theory and proposes a multi-valued logic-based control strategy for attenuation of RGF fluctuation. First, an in-cylinder pressure sensor-based method for measuring the RGF is provided by following the physics of the in-cylinder transient state of four-stroke internal combustion engines. Then, the stochastic property of the RGF is examined based on statistical data obtained by conducting experiments on a full-scale gasoline engine test bench. Based on the observation of the examination, a stochastic logical transient model is proposed to represent the cycle-to-cycle transient behavior of the RGF, and with the model an optimal feedback control law, which targets on rejection of the RGF fluctuation, is derived in the framework of stochastic logical system theory. Finally, experimental results are demonstrated to show the effectiveness of the proposed model and the control strategy.

  20. Biochemical effects of manufactured gas plant residue following ingestion by B6C3F1 mice

    Energy Technology Data Exchange (ETDEWEB)

    Weyand, E.H.; Wu, Yun; Patel, S. (State Univ. of New Jersey, Piscataway, NJ (United States)); Goldstein, L. (Electric Power Research Institute, Palto Alto, CA (United States))

    1994-01-01

    The toxic potential of manufactured gas plant residue (MGP) given in the diet to male and female B6C3F1 mice was evaluated. In addition, the bioavailability of chemical components of MGP were also investigated by monitoring polycyclic aromatic hydrocarbon (PAH) metabolites in urine and DNA adduct formation in forestomach and lung tissue. Basal gel diets containing 0.05, 0.25, 0.50% benzo[a]pyrene (BaP) were fed to animals for 94 and 185 d. Mice readily consumed adulterated diets without any evidence of acute toxicity. The total amount of MGP and BaP consumed by mice ranged from 118 to 2604 mg and from 12 to 29 mg, respectively. Male mice fed a control or BaP diet and female mice fed a 0.05% MGP diet had the highest body weight gains. Male and female mice fed a 0.50% MGP diet had the lowest body weight gains. the bioavailability of chemical components of MGP was evaluated by monitoring the urinary excretion of PAH metabolites by male mice fed a 0.25% MGP diet. 1-Hydroxypyrene was determined by high-performance liquid chromatography analysis to be the major fluorescent metabolite excreted by mice throughout the 185 d of diet administration. At necropsy, no chemical-related gross lesions were detected. In addition, no treatment-related microscopic lesions were evident in tissues obtained from animals fed a 0.50% MGP- or BaP-adulterated diet. The [sup 32]P-postlabeling assay was used to evaluate MGP- and BaP-induced DNA adduct formation in lung and forestomach tissue. The level of DNA adducts formed from the chemical components of MGP paralleled the amount of material ingested by animals. Lung DNA adduct levels were considerably higher than forestomach levels when mice ingested a 0.25% or 0.50% MGP diet. These studies demonstrate that the continuous ingestion of MGP or BaP for 185 d does not result in acute toxicity or chemical-related lesions at doses up to 0.50% MGP or 0.005% BaP. 36 refs., 3 figs., 4 tabs.

  1. Energy and greenhouse gas balance of the use of forest residues for bioenergy production in the UK

    International Nuclear Information System (INIS)

    Whittaker, Carly; Mortimer, Nigel; Murphy, Richard; Matthews, Robert

    2011-01-01

    Life cycle analysis is used to assess the energy requirements and greenhouse gas (GHG) emissions associated with extracting UK forest harvesting residues for use as a biomass resource. Three forest harvesting residues were examined (whole tree thinnings, roundwood and brash bales), and each have their own energy and emission profile. The whole forest rotation was examined, including original site establishment, forest road construction, biomass harvesting during thinning and final clear-fell events, chipping and transportation. Generally, higher yielding sites give lower GHG emissions per ‘oven dried tonne’ (ODT) forest residues, but GHG emissions ‘per hectare’ are higher as more biomass is extracted. Greater quantities of biomass, however, ultimately mean greater displacement of conventional fuels and therefore greater potential for GHG emission mitigation. Although forest road construction and site establishment are “one off” events they are highly energy-intensive operations associated with high diesel fuel consumption, when placed in context with the full forest rotation, however, their relative contributions to the overall energy requirements and GHG emissions are small. The lower bulk density of wood chips means that transportation energy requirements and GHG emissions are higher compared with roundwood logs and brash bales, suggesting that chipping should occur near the end-user of application. -- Highlights: ► GHGs and fuel consumption assessed for UK clear-fell conifer forest residues. ► Energy use and GHG emissions for forest road construction characterised. ► Lower energy requirements and GHG emissions per ODT for higher yielding sites. ► Transport energy and GHG emissions higher for wood chip than roundwood or brash bales. ► Results useful in predicting GHG mitigation potential from UK commercial conifer forest residues.

  2. JV Task 5 - Evaluation of Residual Oil Fly Ash As A Mercury Sorbent For Coal Combustion Flue Gas

    Energy Technology Data Exchange (ETDEWEB)

    Robert Patton

    2006-12-31

    The mercury adsorption capacity of a residual oil fly ash (ROFA) sample collected form Florida Power and Light Company's Port Everglades Power Plant was evaluated using a bituminous coal combustion flue gas simulator and fixed-bed testing protocol. A size-segregated (>38 {micro}g) fraction of ROFA was ground to a fine powder and brominated to potentially enhance mercury capture. The ROFA and brominated-ROFA were ineffective in capturing or oxidizing the Hg{sup 0} present in a simulated bituminous coal combustion flue gas. In contrast, a commercially available DARCO{reg_sign} FGD initially adsorbed Hg{sup 0} for about an hour and then catalyzed Hg{sup 0} oxidation to produce Hg{sup 2+}. Apparently, the unburned carbon in ROFA needs to be more rigorously activated in order for it to effectively capture and/or oxidize Hg{sup 0}.

  3. Development of a multi-residue screening method for the determination of pesticides in cereals and dry animal feed using gas chromatography-triple quadrupole tandem mass spectrometry.

    Science.gov (United States)

    Walorczyk, Stanisław

    2007-09-21

    A multi-residue screening method for simultaneous analysis of 122 gas chromatography amenable pesticides in dry matrices such as cereal grain and certain feedingstuffs was developed. The method entails a simple extraction of re-hydrated sample with acetonitrile followed by a dispersive solid phase extraction (dispersive-SPE) clean-up step prior to the final determination by gas chromatography/triple quadrupole tandem mass spectrometry (GC-MS/MS). Due to complexity of analyzed matrices, two MS/MS transitions were set for each pesticide to eliminate the need for re-analysis of potentially positive samples, and provide unequivocal identification of detected pesticides in accordance with recent guidelines, in a single analytical run. Thus, in the developed GC-MS/MS acquisition method, a total of 216 different multiple reactions monitoring (MRM) transitions were monitored in one set of experimental conditions. To evaluate performance of the method, validation experiments were carried out on wheat grain at three spiking levels (0.01, 0.02 and 0.05 mg kg(-1)). Additional recovery tests at 0.05 mg kg(-1) were carried out on several other matrices. The recoveries ranged between 73 and 129% with associated relative standard deviations between 1 and 29% for the majority of pesticides. Limits of detection were less or equal to 0.01 mg kg(-1) for approximately 68% of pesticides. The applicability of the proposed method to detect and quantify pesticide residues has been demonstrated in the analysis of 136 real samples. Additionally, the method was favorably compared with an acetone extraction method (accepted as a reference method by some of European and U.S. authorities) in the analysis of real samples known to contain pesticide residues.

  4. Residual ground-water levels of the neonicotinoid thiacloprid perturb chemosensing of Caenorhabditis elegans.

    Science.gov (United States)

    Hopewell, Hannah; Floyd, Kieran G; Burnell, Daniel; Hancock, John T; Allainguillaume, Joel; Ladomery, Michael R; Wilson, Ian D

    2017-09-01

    This study investigated the neurological effects of residual ground-water levels of thiacloprid on the non-target organism Caenorhabditis elegans. Nematodes treated with thiacloprid showed a dose-dependent and significantly increased twitch response at concentrations above 50 ng mL -1 that disabled their forward locomotion in liquid culture. In comparison with untreated controls, 10 ng mL -1 thiacloprid perturbed the chemosensory ability of C. elegans such that the nematodes no longer demonstrated positive chemotaxis towards a NaCl chemo-attractant, reducing their chemotaxis index from +0.48 to near to zero. Nematodes also exhibited a locomotion characteristic of those devoid of chemo-attraction, making significantly more pirouetting turns of ≥90° than the untreated controls. Compared to the untreated controls, expression of the endocytosis-associated gene, Rab-10, was also increased in C. elegans that had developed to adulthood in the presence of 10 ng mL -1 thiacloprid, suggesting their active engagement in increased recycling of affected cellular components, such as their nAChRs. Thus, even residual, low levels of this less potent neonicotinoid that may be found in field ground-water had measurable effects on a beneficial soil organism which may have environmental and ecological implications that are currently poorly understood.

  5. Establishing the level of exposure to radon gas in dwellings

    International Nuclear Information System (INIS)

    Karupa, Jackson Uakaningirua

    2016-04-01

    The main source of natural internal irradiation of man is radon and its decay products. In this study, the radon concentration levels in selected dwellings in Erongo region, Swakopmund, Namibia will be estimated using passive or active radon detector. The primary objective of the study is to measure and establish radon levels in selected dwellings in Erongo region, Swakopmund of Namibia. Measurements will be carried out for the period of twelve months and after three months period the detectors will be exchanged for laboratory analysis. The results obtained from the study will reveal the concentration of radon in most of the selected dwellings in Erongo region, Swakopmund, Namibia. Once Radon level is measured or identified, the results with data from work done in other environments in Africa and elsewhere will be compared. In case of high radon concentrations in dwelling, the occupants will be advised to ensure good ventilation practices as cost effective means of mitigation of indoor radon gas level in the area. (au)

  6. Simultaneous determination of organochlorine and pyrethriod pesticide residues in the Chinese patent medicines by gas chromatography-tandem mass spectrometry.

    Science.gov (United States)

    Mao, Xue J; Zhong, Yao; Yan, Ai P; Wang, Bin; Wang, Yuan X; Wan, Yi Q

    2018-02-01

    A simple, sensitive, reliable method was developed for the simultaneous determination of organochlorine and pyrethriod pesticide residues in Chinese patent medicines Six ingredient rehmannia pills and Xiaoyao pills. These pesticides were extracted by ethyl acetate. The extraction time and volume of ethyl acetate were optimized. Cleanup of extracts was performed with dispersive-solid phase extraction using graphitized carbon black as the sorbent. The determination of pesticides in the final extracts was carried out by gas chromatography-tandem mass spectrometry in multiple reaction monitoring mode (GC-MS/MS, MRM). The linearity of the calibration curves is good in matrix-matched standard and yields the coefficients of determination (R 2 ) ≥0.99 for all of the target analytes. Under optimized conditions, the average recoveries (five replicates) for most pesticides range from 75.5% to 114.6%, and RSDs are less than 10.0%. The LODs of 18 pesticides in Six ingredient rehmannia pill and Xiaoyao pills are in the range of 0.01-8.82 μg kg -1 . The developed method meets the requirements of pesticide residue analysis and could be effectively used for routine analysis of the organochlorine and pyrethriod pesticide residues in Six ingredient rehmannia pills and Xiaoyao pills.

  7. Control of postharvest diseases of fruit by heat and fungicides: efficacy, residue levels, and residue persistence. A review.

    Science.gov (United States)

    Schirra, Mario; D'Aquino, Salvatore; Cabras, Paolo; Angioni, Alberto

    2011-08-24

    Extensive research has been done in recent years to reduce the heavy dependence on chemical fungicides to control postharvest diseases and disorders of horticultural crops. Alternative strategies were based on improved cultural practices, biological control, plant-defense promoters, and physical treatments such as UV illumination, radiofrequency treatment, heat therapy, and storage technologies. Among these, postharvest heat treatments such as hot water dips, short hot water rinsing and brushing, and hot air conditioning have reduced rot development and enhanced fruit resistance to chilling injury in sensitive cultivars while retaining fruit quality during cold storage and shelf life. Additive or synergistic increases in effectiveness were observed by integrating heat therapy with various chemical compounds, thus leading to significant reductions in the application of active ingredients to protect produce from decay. This paper highlights the knowledge on this topic with emphasis on heat therapy effects and factors affecting the uptake, persistence, and performance of fungicide residues when they are applied in combination with hot water.

  8. The effects of rape residue mulching on net global warming potential and greenhouse gas intensity from no-tillage paddy fields.

    Science.gov (United States)

    Zhang, Zhi-Sheng; Cao, Cou-Gui; Guo, Li-Jin; Li, Cheng-Fang

    2014-01-01

    A field experiment was conducted to provide a complete greenhouse gas (GHG) accounting for global warming potential (GWP), net GWP, and greenhouse gas intensity (GHGI) from no-tillage (NT) paddy fields with different amounts of oilseed rape residue mulch (0, 3000, 4000, and 6000 kg dry matter (DM) ha(-1)) during a rice-growing season after 3 years of oilseed rape-rice cultivation. Residue mulching treatments showed significantly more organic carbon (C) density for the 0-20 cm soil layer at harvesting than no residue treatment. During a rice-growing season, residue mulching treatments sequestered significantly more organic C from 687 kg C ha(-1) season(-1) to 1654 kg C ha(-1) season(-1) than no residue treatment. Residue mulching significantly increased emissions of CO2 and N2O but decreased CH4 emissions. Residue mulching treatments significantly increased GWP by 9-30% but significantly decreased net GWP by 33-71% and GHGI by 35-72% relative to no residue treatment. These results suggest that agricultural economic viability and GHG mitigation can be achieved simultaneously by residue mulching on NT paddy fields in central China.

  9. The Effects of Rape Residue Mulching on Net Global Warming Potential and Greenhouse Gas Intensity from No-Tillage Paddy Fields

    Science.gov (United States)

    Zhang, Zhi-Sheng; Cao, Cou-Gui; Guo, Li-Jin; Li, Cheng-Fang

    2014-01-01

    A field experiment was conducted to provide a complete greenhouse gas (GHG) accounting for global warming potential (GWP), net GWP, and greenhouse gas intensity (GHGI) from no-tillage (NT) paddy fields with different amounts of oilseed rape residue mulch (0, 3000, 4000, and 6000 kg dry matter (DM) ha−1) during a rice-growing season after 3 years of oilseed rape-rice cultivation. Residue mulching treatments showed significantly more organic carbon (C) density for the 0–20 cm soil layer at harvesting than no residue treatment. During a rice-growing season, residue mulching treatments sequestered significantly more organic C from 687 kg C ha−1 season−1 to 1654 kg C ha−1 season−1 than no residue treatment. Residue mulching significantly increased emissions of CO2 and N2O but decreased CH4 emissions. Residue mulching treatments significantly increased GWP by 9–30% but significantly decreased net GWP by 33–71% and GHGI by 35–72% relative to no residue treatment. These results suggest that agricultural economic viability and GHG mitigation can be achieved simultaneously by residue mulching on NT paddy fields in central China. PMID:25140329

  10. Technology on In-Situ Gas Generation to Recover Residual Oil Reserves

    Energy Technology Data Exchange (ETDEWEB)

    Sayavur Bakhtiyarov

    2008-02-29

    This final technical report covers the period October 1, 1995 to February 29, 2008. This chapter begins with an overview of the history of Enhanced Oil Recovery techniques and specifically, CO2 flood. Subsequent chapters conform to the manner consistent with the Activities, Tasks, and Sub-tasks of the project as originally provided in Exhibit C1 in the Project Management Plan dated September 20, 1995. These chapters summarize the objectives, status and conclusions of the major project activities performed during the project period. The report concludes by describing technology transfer activities stemming from the project and providing a reference list of all publications of original research work generated by the project team or by others regarding this project. The overall objective of this project was a final research and development in the United States a technology that was developed at the Institute for Geology and Development of Fossil Fuels in Moscow, Russia. Before the technology can be convincingly adopted by United States oil and gas producers, the laboratory research was conducted at Mew Mexico Institute of Mining and Technology. The experimental studies were conducted to measure the volume and the pressure of the CO{sub 2} gas generated according to the new Russian technology. Two experimental devices were designed, built and used at New Mexico Tech facilities for these purposes. The designed setup allowed initiating and controlling the reaction between the 'gas-yielding' (GY) and 'gas-forming' (GF) agents proposed by Russian technology. The temperature was controlled, and the generated gas pressure and volume were recorded during the reaction process. Additionally, the effect of surfactant addition on the effectiveness of the process was studied. An alternative GY reactant was tested in order to increase the efficiency of the CO2 gas generation process. The slim tube and the core flood experimental studies were conducted to define

  11. Evaluation of gas chromatography – electron ionization – full scan high resolution Orbitrap mass spectrometry for pesticide residue analysis

    Energy Technology Data Exchange (ETDEWEB)

    Mol, Hans G.J., E-mail: hans.mol@wur.nl; Tienstra, Marc; Zomer, Paul

    2016-09-07

    Gas chromatography with electron ionization and full scan high resolution mass spectrometry with an Orbitrap mass analyzer (GC-EI-full scan Orbitrap HRMS) was evaluated for residue analysis. Pesticides in fruit and vegetables were taken as an example application. The relevant aspects for GC-MS based residue analysis, including the resolving power (15,000 to 120,000 FWHM at m/z 200), scan rate, dynamic range, selectivity, sensitivity, analyte identification, and utility of existing EI-libraries, are assessed and discussed in detail. The optimum acquisition conditions in full scan mode (m/z 50–500) were a resolving power of 60,000 and an automatic-gain-control target value of 3E6. These conditions provided (i) an optimum mass accuracy: within 2 ppm over a wide concentration range, with/without matrix, enabling the use of ±5 ppm mass extraction windows (ii) adequate scan speed: minimum 12 scans/peak, (iii) an intra-scan dynamic range sufficient to achieve LOD/LOQs ≤0.5 pg in fruit/vegetable matrices (corresponding to ≤0.5 μg kg{sup −1}) for most pesticides. EI-Orbitrap spectra were consistent over a very wide concentration range (5 orders) with good match values against NIST (EI-quadrupole) spectra. The applicability for quantitative residue analysis was verified by validation of 54 pesticides in three matrices (tomato, leek, orange) at 10 and 50 μg/kg. The method involved a QuEChERS-based extraction with a solvent switch into iso-octane, and 1 μL hot splitless injection into the GC-HRMS system. A recovery between 70 and 120% and a repeatability RSD <10% was obtained in most cases. Linearity was demonstrated for the range ≤5–250 μg kg{sup −1}. The pesticides could be identified according to the applicable EU criteria for GC-HRMS (SANTE/11945/2015). GC-EI-full scan Orbitrap HRMS was found to be highly suited for quantitative pesticide residue analysis. The potential of qualitative screening to extend the scope makes it an attractive

  12. Control levels for residual contamination in materials considered for recycle and reuse

    International Nuclear Information System (INIS)

    Hill, R.L.; Aaberg, R.L.; Baker, D.A.; Kennedy, W.E. Jr.

    1993-09-01

    Pacific Northwest Laboratory (PNL) is collecting data and conducting technical analyses to support joint efforts by the U.S. Department of Energy (DOE), Office of Environmental Guidance, Air, Water and Radiation Division (DOE/EH-232); by the U.S. Environmental Protection Agency (EPA); and by the U.S. Nuclear Regulatory Commission (NRC) to develop radiological control criteria for the recycle and reuse of scrap materials and equipment that contain residual radioactive contamination. The initial radiological control levels are the concentrations in or on materials considered for recycle or reuse that meet the individual (human) or industrial (electronics/film) dose criteria. The analysis identifies relevant radionuclides, potential mechanisms of exposure, and methods to determine possible non-health-related impacts from residual radioactive contamination in materials considered for recycle or reuse. The generic methodology and scenarios described here provide a basic framework for numerically deriving radiological control criteria for recycle or reuse. These will be adequately conservative for most situations

  13. Levels of organochlorine pesticide residues in blood plasma of various species of birds from India.

    Science.gov (United States)

    Dhananjayan, Venugopal; Muralidharan, Subramanian

    2010-08-01

    Concentrations of organochlorine pesticides (OCPs) were measured in blood plasma of 13 species of birds collected from Ahmedabad, India. Among the various OCPs determined, HCHs and its isomers had higher contribution to the total OCPs. Concentration of summation operatorHCHs varied from 11.4 ng/mL in White ibis Threskiornis melanocephalus to 286 ng/mL in Sarus Crane Grus antigone, while summation operatorDDT ranged between 19 ng/mL in Black Ibis Pseudibis papillosa and 147 ng/mL in Painted Stork Mycteria leucocephala. p,p'-DDE was accounted for more than 50% of total DDT in many of the samples analysed. However, a p,p'-DDT to p,p'-DDE ratio higher than one obtained for many species of birds indicates the recent use of DDT in this study region. The concentrations of cyclodiene insecticides, heptachlor epoxide, dieldrin and total endosulfan ranged from 15.8 to 296.2 ng/mL, below detectable level to 15 and 41.1-153.2 ng/mL, respectively. The pattern of total OCP load generally occurred in the following order: granivores organochlorine residues detected in blood plasma of birds are not indicative of toxicity, the presence of residues in birds over the years (2005-2007) indicates continued exposure to organochlorine compounds. However, continuous monitoring is recommended to facilitate the early identification of risks to the survival of a species.

  14. Determination of daminozide residues in apples using gas chromatography with nitrogen-phosphorus detection

    NARCIS (Netherlands)

    Brinkman, J.H.W.; Dijk, A.G. van; Wagenaar, R.; Quirijns, J.K.

    1996-01-01

    A method was developed for the determination of daminozide in apples using gas chromatography (GC) with nitrogen-phosphorus detection (NPD). Daminozide is hydrolysed to 1,1-dimethylhydrazine (UDMH) by alkaline digestion. The UDMH generated is distilled from the apple matrix, derivatized with

  15. Conversion of forest residues to a clean gas for fuel or synthesis

    Energy Technology Data Exchange (ETDEWEB)

    Feldmann, H.F.; Liu, K.T.; Longanbach, J.R.; Curran, L.M.; Chauhan, S.P.

    1979-01-01

    A program is described for developing a gasification system specifically for wood and other biomass materials which allows greatly increased gasifier throughputs and direct catalysis of wood. Wood ash, which is a by-product of a wood gasification plant, can be used as a gasification catalyst for wood, as it increases gasification rates and promotes the water-gas shift reaction. The high reactivity of even uncatalyzed biomass allows the potential of very high gasifier throughputs. However, the achievement of this potential requires that the gasifier operate at gas velocities higher than those attainable in conventional reactor systems. Stable and very smooth fluidization with uniform mixing and distribution of chips throughout the bed was observed on addition of an entrained sand phase to a fluidized bed of alumina and wood chips. Economc feasibility studies based on utilization of a proprietary Battelle gasification system which utilizes an entrained-phase heat carrier indicated that an intermediate-Btu gas can be produced in 1000 ton/day plants at a price competitive with liquefied natural gas and No. 2 heating oil.

  16. The influence of electrodialytic remediation on dioxin (PCDD/PCDF) levels in fly ash and air pollution control residues

    DEFF Research Database (Denmark)

    Dias-Ferreira, Celia; Kirkelund, Gunvor Marie; Jensen, Pernille Erland

    2016-01-01

    materials dissolve, leaving behind the non-water soluble compounds, such as PCDD/PCDF. According to the Basel Convention, PCDD/PCDF levels in these materials is low (residue could eventually be valorized, for instance as construction material, provided end......Fly ash and Air Pollution Control (APC) residues collected from three municipal solid waste incinerators in Denmark and Greenland were treated by electrodialytic remediation at pilot scale for 8-10 h. This work presents for the first time the effect of electrodialytic treatment on polychlorinated...... dibenzo-p-dioxins (PCDD) and polychlorinated dibenzofurans (PCDF), and how these levels impact on the valorization options for fly ash and APC residue.PCDD/PCDF levels in the original residues ranged between 4.85 and 197 ng g-1, being higher for the electrostatic precipitator fly ash. The toxic equivalent...

  17. Mercury Levels In Fly Ash And Apc Residue From Municipal Solid Waste Incineration Before And After Electrodialytic Remediation

    DEFF Research Database (Denmark)

    Dias-Ferreira, Celia; Kirkelund, Gunvor Marie; Jensen, Pernille Erland

    2016-01-01

    Fly ash (FA) and Air Pollution Control (APC) residues collected from three municipal solid waste incinerators (MSWI) in Denmark and Greenland were treated by electrodialytic remediation at pilot scale for 8 to 10 h. The original residues and the treated material were analysed for mercury (Hg......) in order to assess the influence of the electrodialytic treatment on the concentrations of this element. Mercury levels varied with the MSWI residue, ranging from 0.41 mg kg−1 in FA sample from electrostatic precipitator (ESP) to 8.38 mg kg−1 in MSWI residues from a semi-dry system with lime and activated...... carbon. Two distinct behaviours were observed for mercury as a result of the electrodialytic treatment. This element became enriched in the MSWI residues from the semi-dry system with activated carbon, whereas it decreased in ESP’s and cyclone’s FA. This work presents for the first time information about...

  18. Determination of some selected pesticide residues in apple juice by solid-phase microextraction coupled to gas chromatography – mass spectrometry

    Directory of Open Access Journals (Sweden)

    Andrea Hercegová

    2011-01-01

    Full Text Available The performance of solid phase microextraction (SPME for enrichment of pesticides from apple juice was investigated. Samples were diluted with water, extracted by solid-phase microextraction and analysed by gas chromatography using mass-spectrometry detector (MSD in selected ion monitoring mode (SIM. The method was tested for the following pesticides used mostly in fruit culturing at Slovakia: tebuthylazine, fenitrothion, chlorpyrifos, myclobutanil, cyprodinil, phosalone, pyrimethanil, tebuconazole, kresoxim-methyl, methidathion, penconazole. All pesticides were extracted with polydimethylsiloxane fibre 100 μm thickness. The linear concentration range of application was 0.05 μg dm−3–10 μg dm−3. The method described provides detectabilities complying with the maximum residue levels (MRLs set by regulatory organizations for pesticides in apple juice matrices. The solvent – free SPME procedure was found to be quicker and more cost effective then the solvent extraction methods commonly used.

  19. Pyrolysis Gas as a Renewable Reducing Agent for the Recycling of Zinc- and Lead-Bearing Residues: A Status Report

    Science.gov (United States)

    Pichler, C.; Antrekowitsch, J.

    2017-04-01

    The topic "Zero Waste" has been in existence for several years in the industry, and the metallurgical industry has also made efforts to reduce the amounts of residues occurring and have started several investigations to cut down on metallurgical by-products which have to be landfilled. Especially, the additional costs for CO2 emissions in different metallurgical steps have led to investigations into alternative carbon carriers. Charcoal has been identified to serve as an ideal substitute due its CO2-neutrality. For the applications of this renewable carbon carrier in metallurgical processes, charcoal production by means of a carbonization process needs to be optimized. As a by-product during the heating of agricultural wastes or wood by excluding air, pyrolysis gas occurs. Due to the existence of combustible compounds in this gas, an application as a reduction agent instead of fossil carbon carriers in metallurgy is possible. Based on the prevention of dumping metallurgical by-products, an investigation has been developed to treat zinc- and lead-containing materials. To realize this, a dedicated process concept has been designed and developed. As the main focuses, the usage of the pyrolysis gas from charcoal production for the Waelz kiln process and the recycling of zinc- and lead-containing Waelz slag, resulting from the processing of steel mill dust in a vertical retort, have to be mentioned. Within this research, the process concept was executed from laboratory-scale up to pilot-scale testing, described in this article.

  20. Conversion of forest residues to a methane-rich gas: Interim Report

    Energy Technology Data Exchange (ETDEWEB)

    Feldmann, H.G.; Paisley, M.A.; Appelbaum, H.R.

    1986-03-01

    A process is being developed that produces a fuel gas with a heating value of 500 Btu/SCF from diverse forms of biomass, including shredded bark, wood chips, and sawdust. The system uses a high throughput, non-oxygen gasifier that employs sand circulation to supply process heat. Results obtained with a 10-inch I.D. gasifier are presented and compared with those in a 6-inch I.D. reactor. Feed rates up to 12 tons/day (dry) have been achieved corresponding to a specific wood throughput of 2000 lbs/ft/sup 2/-hr. Gas compositions in the two reactors are in excellent agreement and performance in the larger reactor, as measured by carbon conversion, is significantly improved. Cost projections comparing this process with direct combustion are presented that indicate gasification technology should have very significant cost advantages for both generation of plant steam and cogeneration of electricity. 5 refs., 14 figs., 5 tabs.

  1. A Vapor Challenge Method of Measuring the Residual Life of Gas Filters

    Science.gov (United States)

    1990-08-01

    reaction with chromium complexes . Protection against these gases is so effective that these gases are no longer used in gas warfare; however...To do otherwise, would increase the complexity of the test, and provide a less direct measurement of filter performance under actual operation. Second...detected by colorimetric reactions with: * chromotropic acid; 6 J-acid; 0 metal precipitation from nickel dimethylglyoxime ; or 0 metal precipitation from

  2. Determination of the residue levels of nicarbazin and combination nicarbazin-narasin in broiler chickens after oral administration

    Science.gov (United States)

    da Silva, Guilherme Resende; de Assis, Débora Cristina Sampaio; Cançado, Silvana de Vasconcelos

    2017-01-01

    The depletion times of the anticoccidial nicarbazin administered individually and of nicarbazin and narasin administered in combination were evaluated by determining the presence and levels of 4,4'-dinitrocarbanilide (DNC), the marker residue for nicarbazin, and narasin residues in the muscle tissues of broiler chickens subjected to a pharmacological treatment. A high-performance liquid chromatography-tandem mass spectrometry (HPLC-MS/MS) method was used. The results showed the presence of all anticoccidial residues; however, the DNC levels were higher when the nicarbazin was administered individually than when it was used in association with narasin throughout the experimental period. After six days of withdrawal, the DNC level following nicarbazin administration alone was lower than the maximum residue level (MRL) of 200 μg kg-1. However, when the nicarbazin was co-administered with narasin, the concentrations of DNC were lower than the MRL after four days of withdrawal. These results may be justified because the dosage of nicarbazin, when administrated individually, is greater than when it is used in combination with narasin. The levels of narasin were lower than the MRL of 15 μg kg-1 throughout the evaluation period. It was concluded that nicarbazin is rapidly metabolized from the broiler muscles up to six days of withdrawal since the DNC levels were lower than the maximum residue level (MRL) and the concentrations of narasin were lower than the MRL throughout the evaluation period. PMID:28750013

  3. Determination of the residue levels of nicarbazin and combination nicarbazin-narasin in broiler chickens after oral administration.

    Science.gov (United States)

    Lima, Arina Lopes de; Barreto, Fabiano; Rau, Renata Batista; Silva, Guilherme Resende da; Lara, Leonardo José Camargos; Figueiredo, Tadeu Chaves de; Assis, Débora Cristina Sampaio de; Cançado, Silvana de Vasconcelos

    2017-01-01

    The depletion times of the anticoccidial nicarbazin administered individually and of nicarbazin and narasin administered in combination were evaluated by determining the presence and levels of 4,4'-dinitrocarbanilide (DNC), the marker residue for nicarbazin, and narasin residues in the muscle tissues of broiler chickens subjected to a pharmacological treatment. A high-performance liquid chromatography-tandem mass spectrometry (HPLC-MS/MS) method was used. The results showed the presence of all anticoccidial residues; however, the DNC levels were higher when the nicarbazin was administered individually than when it was used in association with narasin throughout the experimental period. After six days of withdrawal, the DNC level following nicarbazin administration alone was lower than the maximum residue level (MRL) of 200 μg kg-1. However, when the nicarbazin was co-administered with narasin, the concentrations of DNC were lower than the MRL after four days of withdrawal. These results may be justified because the dosage of nicarbazin, when administrated individually, is greater than when it is used in combination with narasin. The levels of narasin were lower than the MRL of 15 μg kg-1 throughout the evaluation period. It was concluded that nicarbazin is rapidly metabolized from the broiler muscles up to six days of withdrawal since the DNC levels were lower than the maximum residue level (MRL) and the concentrations of narasin were lower than the MRL throughout the evaluation period.

  4. [Analysis of residues of organochlorine compounds in plant drugs. 3. Identification of residues of polychlorobiphenyl compounds by comparison of gas chromatography on packed and capillary columns and GCMS coupling].

    Science.gov (United States)

    Benecke, R; Brotka, J; Wijsbeek, J; Franke, J P; Bruins, A P; de Zeeuw, R A

    1988-02-01

    The identification of residues of polychlorinated biphenyls in a test sample of Flores Chamomillae could be achieved by the retention behavior at gas chromatographic analyses on packed and capillary columns compared with reference standard Clophen A 60, respectively as well as well by capillary GC/MS using single ion monitoring of substance-characteristic ion mass.

  5. Determination of residual acetone and acetone related impurities in drug product intermediates prepared as Spray Dried Dispersions (SDD) using gas chromatography with headspace autosampling (GCHS).

    Science.gov (United States)

    Quirk, Emma; Doggett, Adrian; Bretnall, Alison

    2014-08-05

    Spray Dried Dispersions (SDD) are uniform mixtures of a specific ratio of amorphous active pharmaceutical ingredient (API) and polymer prepared via a spray drying process. Volatile solvents are employed during spray drying to facilitate the formation of the SDD material. Following manufacture, analytical methodology is required to determine residual levels of the spray drying solvent and its associated impurities. Due to the high level of polymer in the SDD samples, direct liquid injection with Gas Chromatography (GC) is not a viable option for analysis. This work describes the development and validation of an analytical approach to determine residual levels of acetone and acetone related impurities, mesityl oxide (MO) and diacetone alcohol (DAA), in drug product intermediates prepared as SDDs using GC with headspace (HS) autosampling. The method development for these analytes presented a number of analytical challenges which had to be overcome before the levels of the volatiles of interest could be accurately quantified. GCHS could be used after two critical factors were implemented; (1) calculation and application of conversion factors to 'correct' for the reactions occurring between acetone, MO and DAA during generation of the headspace volume for analysis, and the addition of an equivalent amount of polymer into all reference solutions used for quantitation to ensure comparability between the headspace volumes generated for both samples and external standards. This work describes the method development and optimisation of the standard preparation, the headspace autosampler operating parameters and the chromatographic conditions, together with a summary of the validation of the methodology. The approach has been demonstrated to be robust and suitable to accurately determine levels of acetone, MO and DAA in SDD materials over the linear concentration range 0.008-0.4μL/mL, with minimum quantitation limits of 20ppm for acetone and MO, and 80ppm for DAA. Copyright

  6. Study of radiolytic effect on residual ethylene oxide in perfusion devices for single use by using gas chromatography

    International Nuclear Information System (INIS)

    Wang Mingsuo; Teng Weifang; Liu Keliang; Feng Jixin; Su Liaoyuan

    1993-01-01

    The efficiency of the 60 Co γ-rays irradiation induced elimination reaction of residual ethylene oxide (RETO) in the perfusion devices for single use conducted with RETO gas chromatography has been studied. The observations show: 1. the splinting reaction of RETO absorbed by the infusion sets after ethylene oxide (ETO) sterilization occurred accompanied with 4 kGy irradiation, therefore the relative elimination percentage (RELP) calculated from RETO is over 90%. 2. the optimum radiation conditions are as following irradiation dose 4 kGy, dose rate 8 Gy/min, irradiation temperature 20 degree C. 3. the RETO content within medical infusion sets at 2 weeks storing time after radiation was probably controlled under 2.0 ppm. 4. the radiation chemistry mechanism of the RETO elimination reaction is discussed in relation to the primary and secondary actions of elimination reaction

  7. Derivation of residual radionuclide inventory guidelines for implace closure of high-level waste tanks

    International Nuclear Information System (INIS)

    Yuan, L.; Yuan, Y.

    1999-01-01

    Residual radionuclide inventory guidelines were derived for the high-level waste tanks at a vitrification facility. The decommissioning scenario assumed for this derivation was that the tanks were to be stabilized at the present locations and the site is released for unrestricted use following a 100-year institutional control period. It was assumed that loss of institutional control would occur at 100-years following tank closure. The derivation of the residual radionuclide inventory guidelines was based on the requirement that the effective dose equivalent (EDE) to a hypothetical individual who lives in the vicinity of the site should not exceed a dose of 0.15 mSv/yr off-site and 5 mSv/yr on-site following closure of the tanks. The RESRAD computer code, modified for exposure scenarios specific for the site, was used for this evaluation. The results of the derivation indicate that the allowable off-site dose limit will not be exceeded. The estimated potential doses to individuals using water offsite from a creek are negligibly small fractions of the 0.15 mSv/yr allowable dose limit. With an assumed 3% heel remaining in the tanks, the estimated peak dose rate for the future offsite water user is about 0.00025 mSv/yr. The residual radionuclide inventory guidelines derived based on potential doses to the on-site resident farmer indicate that, with the exception of Tc-99 and C-14, a 3% heel remaining in the tanks would not result in doses exceeding the 5 mSv/yr allowable dose limit. For this on-site exposure scenario, the peak dose rates occur at about 2000 years after tank closure. The peak dose rate is calculated to be 25 mSv/yr, with greater than 99% produced by four radionuclides: C-14, Tc-99, Np-237, and Am-241. Ingestion of contaminated vegetation contributes most (90%) of the peak dose. Since the inventories used for the derivation are mostly estimated from fuel depletion calculations. There is a need to determine further the actual inventories of these

  8. Validation of a new analytical procedure for determination of residual solvents in [{sup 18}F]FDG by gas chromatography

    Energy Technology Data Exchange (ETDEWEB)

    Costa, Flávia M.; Costa, Cassiano L.S.; Silva, Juliana B.; Ferreira, Soraya M.Z.M.D., E-mail: flaviabiomedica@yahoo.com.br [Centro de Desenvolvimento da Tecnologia Nuclear (UPPR/CDTN/CNEN-MG), Belo Horizonte, MG (Brazil). Unidade de Pesquisa e Produção de Radiofármacos

    2017-07-01

    Fludeoxyglucose F 18 ([{sup 18}F]FDG) is the most used radiopharmaceutical for positron emission tomography, especially on oncology. Organic solvents such as ether, ethanol and acetonitrile might be used in the synthesis of [{sup 18}F]FDG; however, they might not be completely removed during purification steps. The determination of residual solvents in [{sup 18}F]FDG is required in the European Pharmacopoeia (EP) and the United States Pharmacopeia (USP) monographs. While the procedure described in the EP is quite general, the one described in the USP requires a long runtime (about 13 minutes). In this work a simple and fast (4-minute) analytical procedure was developed and validated for determination of residual solvents in [{sup 18}F]FDG. Analyses were carried out in a Perkin Elmer gas chromatograph equipped with a flame ionization detector. The separation was obtained on a 0.53-mm x 30 m fused-silica column. Validation included the evaluation of various parameters, such as: specificity, linearity and range, limits of detection and quantitation, precision (repeatability and intermediate precision), accuracy, and robustness. Results were found to be within acceptable limits, indicating the developed procedure is suitable for its intended application. Considering the short half-life of fluorine-18 (109.7 minutes), this new method could be a valuable alternative for routine quality control of [{sup 18}F]FDG. (author)

  9. [Determination of pesticide residues in fugu, eel and prawn using gas chromatography-mass spectrometry with gel permeation chromatographic clean-up].

    Science.gov (United States)

    Zheng, Feng; Pang, Guofang; Li, Yan; Wang, Minglin; Fan, Chunlin

    2009-09-01

    A multiresidue analytical method was developed for the determination of 191 pesticides in fugu, eel and prawn using gas chromatography-mass spectrometry (GC-MS). The samples were extracted with ethyl acetate and cyclohexane (1:1, v/v), and cleaned-up by gel permeation chromatography (GPC). The GPC eluant collected from 26 min to 44 min was concentrated to 1 mL, then analyzed using GC-MS. A DB-1701 column was used for the separation. The MS detection was performed in selected ion monitoring mode. The recoveries were determined at the two spiked levels of I LOQ and 4 LOQ (LOQ: limit of quantification). The overall recoveries were from 50.2% to 120%, and in which the recoveries of 89.5% pesticides were from 70% to 120%. The relative standard deviations (RSDs) of the recoveries were from 0.6% to 21.6%. The calibration curves of all pesticides showed good linearities in the respective ranges with the correlation coefficient above 0.97. The limits of detection and the limits of quantification were 0.002-0.3 mg/kg and 0.007-1.2 mg/kg, respectively. The sensitivity and accuracy of the method met the requirements of the multiple pesticide residues. This method was applicable to determine 191 multiple pesticide residues in fugu, eel, prawn and other fishes.

  10. Determination of an acceptable assimilable organic carbon (AOC) level for biological stability in water distribution systems with minimized chlorine residual.

    Science.gov (United States)

    Ohkouchi, Yumiko; Ly, Bich Thuy; Ishikawa, Suguru; Kawano, Yoshihiro; Itoh, Sadahiko

    2013-02-01

    There is considerable interest in minimizing the chlorine residual in Japan because of increasing complaints about a chlorinous odor in drinking water. However, minimizing the chlorine residual causes the microbiological water quality to deteriorate, and stricter control of biodegradable organics in finished water is thus needed to maintain biological stability during water distribution. In this investigation, an acceptable level of assimilable organic carbon (AOC) for biologically stable water with minimized chlorine residual was determined based on the relationship between AOC, the chlorine residual, and bacterial regrowth. In order to prepare water samples containing lower AOC, the fractions of AOC and biodegradable organic matter (BOM) in tap water samples were reduced by converting into biomass after thermal hydrolysis of BOM at alkaline conditions. The batch-mode incubations at different conditions of AOC and chlorine residual were carried out at 20 °C, and the presence or absence of bacterial regrowth was determined. The determined curve for biologically stable water indicated that the acceptable AOC was 10.9 μg C/L at a minimized chlorine residual (0.05 mg Cl(2)/L). This result indicated that AOC removal during current water treatment processes in Japan should be significantly enhanced prior to minimization of the chlorine residual in water distribution.

  11. The residuals analysis project: Evaluating disposal options for treated mixed low-level waste

    International Nuclear Information System (INIS)

    Waters, R.D.; Gruebel, M.M.; Case, J.T.; Letourneau, M.J.

    1997-01-01

    For almost four years, the U.S. Department of Energy (DOE) through its Federal Facility Compliance Act Disposal Workgroup has been working with state regulators and governors' offices to develop an acceptable configuration for disposal of its mixed low-level waste (MLLW). These interactions have resulted in screening the universe of potential disposal sites from 49 to 15 and conducting ''performance evaluations'' for those fifteen sites to estimate their technical capabilities for disposal of MLLW. In the residuals analysis project, we estimated the volume of DOE's MLLW that will require disposal after treatment and the concentrations of radionuclides in the treated waste. We then compared the radionuclide concentrations with the disposal limits determined in the performance evaluation project for each of the fifteen sites. The results are a scoping-level estimate of the required volumetric capacity for MLLW disposal and the identification of waste streams that may pose problems for disposal based on current treatment plans. The analysis provides technical information for continued discussions between the DOE and affected States about disposal of MLLW and systematic input to waste treatment developers on disposal issues

  12. Allowable residual contamination levels for decommissioning. Part 2. A summary of example results

    International Nuclear Information System (INIS)

    Kennedy, W.E. Jr.; Napier, B.A.

    1985-01-01

    This paper contains a description of the results of a study sponsored by UNC Nuclear Industries to determine Allowable Residual Contamination Levels (ARCL) for decommissioning facilities in the 100 Areas of the Hanford Site. ARCL results are presented both for surface contamination remaining in facilities (in dpm/100 cm 2 ) and for unconfined surface and confined subsurface soil conditions (in pCi/g). Two confined soil conditions are considered: contamination at depths between 1 and 4 m, and contamination at depths greater than or equal to 5 m. A set of worksheets are discussed for modifying the ARCL values to accommodate changes in the radionuclide mixture or concentrations, to consider the impacts of radioactive decay, and to predict instrument responses. Finally, a comparison is made between the unrestricted release ARCL values for the 100 Area facilities and existing decommissioning and land disposal regulations. For surface contamination, the comparison shows good agreement for a selected annual dose limit. For soil contamination, the comparison shows good agreement if reasonable modification factors are applied to account for the differences in modeling soil contamination and licensed low-level waste. 6 references, 1 figures, 4 tables

  13. Morphology and composition of pyrotechnic residues formed at different levels of confinement

    NARCIS (Netherlands)

    Vermeij, E.; Duvalois, W.; Webb, R.; Koeberg, M.

    2009-01-01

    Post explosion residues (PER) are residues from pyrotechnic compositions or explosives that are generated during an explosion. In the recent past SEM/EDX was used several times to analyze PER from pyrotechnic compositions. The results from these studies suggest that there might be a difference in

  14. Levels of pesticide residues in irrigation effluent from tomato fields in ...

    African Journals Online (AJOL)

    Pesticide residues lindane, chlorpyrifos and endosulfan sulphate were detected in water from the spring source, within field and return channel of vegetable farms in Ngarenanyuki, Tanzania. Extraction of the pesticide residues were conducted by liquid-liquid extraction (LLE) method. The detection and concentrations of ...

  15. Method for Reduction of Pesticide Residue Levels in Raspberry and Blackcurrant Based on Utilization of Ozone

    Directory of Open Access Journals (Sweden)

    Balawejder Maciej

    2014-12-01

    Full Text Available The method for the reduction of pesticide residues in soft fruits based on utilization of ozone was proposed. The procedure allows for effective reduction of boscalid residues by 38% in raspberries, and about 58% thiram in blackcurrants. Furthermore, it can be used on an industrial scale.

  16. The influence of electrodialytic remediation on dioxin (PCDD/PCDF) levels in fly ash and air pollution control residues.

    Science.gov (United States)

    Dias-Ferreira, Celia; Kirkelund, Gunvor M; Jensen, Pernille E

    2016-04-01

    Fly ash and Air Pollution Control (APC) residues collected from three municipal solid waste incinerators in Denmark and Greenland were treated by electrodialytic remediation at pilot scale for 8-10 h. This work presents for the first time the effect of electrodialytic treatment on polychlorinated dibenzo-p-dioxins (PCDD) and polychlorinated dibenzofurans (PCDF), and how these levels impact on the valorization options for fly ash and APC residue. PCDD/PCDF levels in the original residues ranged between 4.85 and 197 ng g(-1), being higher for the electrostatic precipitator fly ash. The toxic equivalent (TEQ) varied ten fold, ranging 0.18-2.0 ng g(-1) I-TEQ, with penta and hexa-homologs being most significant for toxicity. After the electrodialytic treatment PCDD/PCDF levels increased in the residues (between 1.4 and 2.0 times). This does not mean PCDD/PCDF were synthesized, but else that soluble materials dissolve, leaving behind the non-water soluble compounds, such as PCDD/PCDF. According to the Basel Convention, PCDD/PCDF levels in these materials is low (residue could eventually be valorized, for instance as construction material, provided end-of-waste criteria are set and that a risk assessment of individual options is carried out, including the end-of-life stage when the materials become waste again. Copyright © 2016 Elsevier Ltd. All rights reserved.

  17. [Residual levels of acetochlor in source water and drinking water of China's major cities].

    Science.gov (United States)

    Yu, Zhi-Yong; Jin, Fen; Li, Hong-Yan; An, Wei; Yang, Min

    2014-05-01

    The concentration levels of acetochlor were investigated in source water and drinking water from 36 major cities in China by solid phase extraction (SPE) combined with gas chromatography - mass spectrometry (GC-MS). Acetochlor detection rate was 66.9% in all the 145 source water samples collected with an average concentration of 33.9 ng L-1. The average removal rate of acetochlor was limited through the drinking water treatment process. The detection concentration of the northeast region was the highest. The concentrations of acetochlor detected in lake were higher than those in river and groundwater as source water. The detection rate and concentration of Liaohe river watershed and the coastal watershed were the highest.

  18. Radiation exposure and radon levels in some stations of the Syrian gas company

    International Nuclear Information System (INIS)

    Al-Masri, M. S.; Shwekani, R.; Jerbi, B.; Awad, I.

    2006-06-01

    In the present study, exposure levels and radon concentrations have been measured in natural gas production lines at the Syrian gas company. The study area includes gas stations for directories of Der Ezzor, Al-Jbessa, Al-Hassaka, and the middle region. The results showed that radiation exposure rates in remote stations and internal stations were within the natural levels except for two main locations, viz reflex pumps and propane production unites; 3 μSvhr -1 was reported. Radon concentration in Syrian natural gas varied between 15.4 Bqm - 3 and 1141 Bqm - 3; coproduced natural gas was found to contain higher concentration that the free natural gas. In addition, radon concentrations were higher in the central processing facilities that the well heads; these high levels are due to pressurizing and concentrating processes that enhance radon gas and its daughters concentrations in these stations. Moreover, a value of 659 Bqm - 3 in Al-Jbessa directorate gas and 225 Bqm - 3 in Al-Hassaka directorate gas were reported. While the concentration was lower in gas producing safur; a value of 80 Bqm - 3 was observed. On the other hand, maximum radon gas concentrations and its daughters in workplace air environment was found to be relatively high in the gas analysis laboratory and they are due to gas release inside the lab during analysis in addition to good separation of these laboratories from the surrounding environment. (author)

  19. A method for determining allowable residual contamination levels of radionuclide mixtures in soil

    International Nuclear Information System (INIS)

    Napier, B.A.

    1982-05-01

    An important consideration in the disposal of radioactive wastes, and consequently in the preparation of plans for remedial actions at contaminated sites, is the amount of radioactive contamination that may be allowed to remain at any particular waste site. The allowable residual contamination level (ARCL) is dependent on the radiation dose limit imposed, the physical and environmental characteristics of the waste site, and the time at which exposure to the wastes is assumed to occur. The steps in generating an ARCL are generally as follows: (1) develop plausible, credible site-specific exposure scenario; (2) calculate maximum annual radiation doses to an individual for each radionuclide based on the existing physical characteristics of the waste site and the site-specific exposure scenario; (3) calculate the ARCL for the dose limit desired, including all radionuclides present, uncorrected for site cleanup or barrier considerations; and (4) apply any corrections for proposed cleanup activity or addition of barriers to waste migration or uptake to obtain the ARCL applicable to the proposed action. Use of this method allows appropriate application of resources to achieve uniform compliance with a single regulatory standard, i.e., a radiation dose rate limit. Application and modification of the ARCL method requires appropriate models of the environmental transport and fate of radionuclides. Example calculations are given for several specific waste forms and waste site types in order to demonstrate the technique and generate comparisons with other approaches

  20. Allowable Residual Contamination Levels in soil for decommissioning the Shippingport Atomic Power Station site

    International Nuclear Information System (INIS)

    Kennedy, W.E. Jr.; Napier, B.A.; Soldat, J.K.

    1983-09-01

    As part of decommissioning the Shippingport Atomic Power Station, a fundamental concern is the determination of Allowable Residual Contamination Levels (ARCL) for radionuclides in the soil at the site. The ARCL method described in this report is based on a scenario/exposure-pathway analysis and compliance with an annual dose limit for unrestricted use of the land after decommissioning. In addition to naturally occurring radionuclides and fallout from weapons testing, soil contamination could potentially come from five other sources. These include operation of the Shippingport Station as a pressurized water reactor, operations of the Shippingport Station as a light-water breeder, operation of the nearby Beaver Valley reactors, releases during decommissioning, and operation of other nearby industries, including the Bruce-Mansfield coal-fired power plants. ARCL values are presented for 29 individual radionculides and a worksheet is provided so that ARCL values can be determined for any mixture of the individual radionuclides for any annual dose limit selected. In addition, a worksheet is provided for calculating present time soil concentration value that will decay to the ARCL values after any selected period of time, such as would occur during a period of restricted access. The ARCL results are presented for both unconfined (surface) and confined (subsurface) soil contamination. The ARCL method and results described in this report provide a flexible means of determining unrestricted-use site release conditions after decommissioning the Shippingport Atomic Power Station

  1. Variability of matrix effects in liquid and gas chromatography - mass spectrometry analysis of pesticide residues after QuEChERS sample preparation of different food crops

    Science.gov (United States)

    Gas and liquid chromatography (GC and LC) coupled to sophisticated mass spectrometry (MS) instruments are among the most powerful analytical tools currently available to monitor pesticide residues in food, among other applications. However, both GC-MS and LC-MS are susceptible to matrix effects whi...

  2. Adaptive nitrogen and integrated weed management in conservation agriculture: impacts on agronomic productivity, greenhouse gas emissions, and herbicide residues.

    Science.gov (United States)

    Oyeogbe, Anthony Imoudu; Das, T K; Bhatia, Arti; Singh, Shashi Bala

    2017-04-01

    Increasing nitrogen (N) immobilization and weed interference in the early phase of implementation of conservation agriculture (CA) affects crop yields. Yet, higher fertilizer and herbicide use to improve productivity influences greenhouse gase emissions and herbicide residues. These tradeoffs precipitated a need for adaptive N and integrated weed management in CA-based maize (Zea mays L.)-wheat [Triticum aestivum (L.) emend Fiori & Paol] cropping system in the Indo-Gangetic Plains (IGP) to optimize N availability and reduce weed proliferation. Adaptive N fertilization was based on soil test value and normalized difference vegetation index measurement (NDVM) by GreenSeeker™ technology, while integrated weed management included brown manuring (Sesbania aculeata L. co-culture, killed at 25 days after sowing), herbicide mixture, and weedy check (control, i.e., without weed management). Results indicated that the 'best-adaptive N rate' (i.e., 50% basal + 25% broadcast at 25 days after sowing + supplementary N guided by NDVM) increased maize and wheat grain yields by 20 and 14% (averaged for 2 years), respectively, compared with whole recommended N applied at sowing. Weed management by brown manuring (during maize) and herbicide mixture (during wheat) resulted in 10 and 21% higher grain yields (averaged for 2 years), respectively, over the weedy check. The NDVM in-season N fertilization and brown manuring affected N 2 O and CO 2 emissions, but resulted in improved carbon storage efficiency, while herbicide residuals in soil were significantly lower in the maize season than in wheat cropping. This study concludes that adaptive N and integrated weed management enhance synergy between agronomic productivity, fertilizer and herbicide efficiency, and greenhouse gas mitigation.

  3. Illegal treatment of barrows with nandrolone ester: effect on growth, histology and residue levels in urine and hair

    NARCIS (Netherlands)

    Groot, M.J.; Lasaroms, J.J.P.; Bennekom, van E.O.; Meijer, T.; Vinyeta, E.; Klis, van der J.D.; Nielen, M.W.F.

    2012-01-01

    The effect of 17ß-19-nortestosterone (17ßNT) treatment of barrows on residue levels and growth was evaluated. Five barrows were treated three times during the fattening period with 17ßNT phenylpropionate (Nandrosol, nandrolone phenylpropionate 50¿mg/ml,1¿mg/kg body weight). Another five barrows were

  4. Environmental Stress Testing of the Single Sample Cylinder: A Proven Consensus Standard for Internal Gas Analysis (IGA) or Residual Gas Analysis (RGA)

    Science.gov (United States)

    Schuessler, Philipp WH

    2010-01-01

    In August 2008, Schuessler Consulting was contracted by NASA GSFC in support of the NASA Electronic Parts and Packaging (NEPP) program to perform two separate studies on moisture laden air in a stainless steel cylinder that had been designed to become a consensus standard for Test Method 1018. This Test Method was originally released for hybrids under Mil. Std. 883 but was quickly utilized on other microelectronic devices under the auspice of Mil. Std. 750. The cylinder had subsequently been fabricated for the 750 community. It was back-filled with moist air and subsequently analyzed over a period of time under a previous NASA contract. It had been shown that moisture in the 4000 - 5000 ppm range could be analyzed rather precisely with a mass spectrometer, commonly referred to as a Residual Gas Analyzer (RGA). The scope of this study was to ascertain if the composition and precision varied as a function of thermal shock at sub-zero temperatures and whether there was consensus when the standard was submitted to other RGA units. It was demonstrated and published that the consensus standard would yield precise RGA data for moisture within +/- 1% when optimized for a given RGA unit. It has been subsequently shown in this study at Oneida Research Services, that sub-zero storage did not affect that precision when a well-defined protocol for the analysis was followed. The consensus standard was taken to a second facility for analysis where it was found that moisture adsorption on the transfer lines caused precision to drop to +/- 12%. The Single Sample Cylinder (SSC) is a one liter stainless steel cylinder with associated sampling valves and has considerable weight and volume. But this considerable size allows for approximately 300 gas samples of the same composition to be delivered to any RGA unit. Lastly, a smaller cylinder, approximately 75 cc, of a second consensus standard was fabricated and tested with a different mix of fixed gases where moisture was kept in the

  5. Determination of pyrethroid pesticide residues in processed fruits and vegetables by gas chromatography with electron capture and mass spectrometric detection.

    Science.gov (United States)

    Sannino, Anna; Bandini, Mirella; Bolzoni, Luciana

    2003-01-01

    A gas chromatographic method was developed for the simultaneous determination of 12 pyrethroids (tefluthrin, bifenthrin, fenpropathrin, cyhalothrin, permethrin, cyfluthrin, cypermethrin, alpha-cypermethrin, flucythrinate, fenvalerate, fluvalinate, and deltamethrin) in tomato puree, peach nectar, orange juice, and canned peas. A miniaturized extraction-partition procedure requiring small amounts of nonchlorinated solvents is used. Samples are extracted with acetone, partitioned with ethyl acetate-cyclohexane (50 + 50, v/v), and cleaned up on a Florisil cartridge. The final extract is analyzed by gas chromatography with both electron capture and mass spectrometric detection modes. Studies at fortification levels of 0.010-0.100 mg/kg gave mean recoveries ranging from 70.2 to 96.0% and coefficients of variation between 4.0 and 13.9% for all compounds. Quantitation limits were < 0.010 mg/kg for electron capture detection.

  6. Evaluation of Pentachlorophenol Residues in Some Hygienic Papers Prepared from Virgin and Secondary Pulp by Electron Capture Gas Chromatographic Method

    Directory of Open Access Journals (Sweden)

    Behrouz Akbari-adergani

    2016-01-01

    Full Text Available In this study, residual amount of pentachlorophenol (PCP as the most important paper preservative, which is extremely hazardous pollutant, was determined in some tissue papers and napkins. Twenty-five samples of two producing hygienic paper factories prepared from virgin and secondary pulp were analyzed for the presence of trace amount of PCP. The analytical procedure involved direct extraction of PCP from hygienic paper and its determination by gas chromatography with electron capture detection. The statistical results for the analysis of all samples revealed that there were significant differences between mean of PCP in hygienic papers prepared from virgin and secondary pulp (P<0.05. This method gave recoveries of 86-98% for hygienic paper made from virgin pulp and 79-92% for hygienic paper made from secondary pulp. The limit of detection (LOD and limit of quantification (LOQ for PCP were 6.3 and 21.0 mg/kg, respectively. The analytical method has the requisite sensitivity, accuracy, precision and specificity to assay PCP in hygienic papers. This study demonstrates a concern with exposition to PCP considering that hygienic paper is largely consumed in the society.

  7. Residual gas analysis of a cryostat vacuum chamber during the cool down of SST - 1 superconducting magnet field coil

    International Nuclear Information System (INIS)

    Semwal, P.; Joshi, K.S.; Thankey, P.L.; Pathan, F.S.; Raval, D.C.; Patel, R.J.; Pathak, H.A.

    2005-01-01

    One of the most important feature of Steady state Superconducting Tokamak -1 (SST-l) is the Nb-Ti superconducting magnet field coils. The coils will be kept in a high vacuum chamber (Cryostat) and liquid Helium will be flown through it to cool it down to its critical temperature of 4.5K. The coil along with its hydraulics has four types of joints (1) Stainless Steel (S.S.) to Copper (Cu) weld joints (2) S. S. to S. S. weld joints (3) Cu to Cu brazed joints and (4) G-10 to S. S. joints with Sti-cast as the binding material. The joints were leak tested with a Helium mass spectrometer leak detector in vacuum as well as in sniffer mode. However during the cool-down of the coil, these joints may develop leaks. This would deteriorate the vacuum inside the cryostat and coil cool-down would subsequently become more difficult. To study the effect of cooling on the vacuum condition of the Cryostat, a dummy Cryostat chamber was fabricated and a toroidal Field (TF) magnet was kept inside this chamber and cooled down to 4.5 K.A residual gas analyzer (RGA) was connected to the Cryostat chamber to study the behaviour of major gases inside this chamber with temperature. An analysis of the RGA data acquired during the coo-down has been presented in this chamber. (author)

  8. Determination of alkylphenolic residues in fresh fruits and vegetables by extractive steam distillation and gas chromatography-mass spectrometry.

    Science.gov (United States)

    Yang, Deng-Kai; Ding, Wang-Hsien

    2005-09-23

    This study describes a simple and sensitive method for determining the alkylphenolic compounds, 4-tert-octylphenol (4-t-OP), 4-nonylphenol isomers (4-NPs), and their monoethoxylates (4-t-OP1EO and 4-NP1EOs), in fresh fruits and vegetables. The method involves extracting a sample by a modified Nielson-Kryger steam distillation extraction using n-hexane for 1 h. The alkylphenolic compounds were identified and quantitated by gas chromatography-mass spectrometry (GC-MS) in selected ion monitoring (SIM) mode. Various pH values and amounts of NaCl added to the sample solution were evaluated as extraction conditions. The quantitation limit of this method was less than 0.2 ng/g in 10 g (fresh weight) of sample. Recovery of alkylphenolic compounds in spiked samples exceeded 64% while R.S.D. ranged from 1.0 to 9.8%. Alkylphenolic residues were detected in fresh fruits and vegetables at concentrations of 4-NPs and 4-t-OP from n.d. to 16 ng/g and from n.d. to 4.8 ng/g (fresh weight), respectively. NP1EO and OP1EO were always below the quantitation limit.

  9. Determination of alkylphenol residues in baby-food purees by steam distillation extraction and gas chromatography-mass spectrometry.

    Science.gov (United States)

    Li, Chia-Tien; Cheng, Chin-Yuan; Ding, Wang-Hsien

    2008-02-01

    This paper describes a simple and sensitive method for determining alkylphenols namely 4-tert-octylphenol (4-t-OP) and the isomers of 4-nonylphenol (4-NPs) present in various types of baby-food purees. The method involves extracting a sample with n-hexane for 1h using a modified Nielson-Kryger steam distillation extraction system and then identifying and quantitating the alkylphenols using a gas chromatography-mass spectrometry (GC-MS) operated in the selected ion monitoring (SIM) mode. The extraction conditions were evaluated at various values of pH of the sample solution. The limits of quantitation for this method were 0.2 ng/g from 1.0 g (wet weight) samples of 4-t-OP and the 4-NPs. The intra- and interbatch precisions and accuracies were also determined. The precision, in terms of the relative standard deviation (RSD), were less than 8%. Most of the recoveries of the alkylphenols from various spiked samples exceeded 60%, while the values of RSD ranged from 1% to 10%. Alkylphenol residues were detected in baby-food purees at concentrations of up to 19 ng/g (wet weight) for 4-t-OP and up to 21 ng/g (wet weight) for the 4-NPs.

  10. Optimization of a multi-residue method for 101 pesticides in green tea leaves using gas chromatography–tandem mass spectrometry

    Directory of Open Access Journals (Sweden)

    Xue Hou

    Full Text Available ABSTRACT A method for analysis of 101 pesticide residues in tea leaves was developed and validated for the first time. Pure acetonitrile was used as extraction solvent rather than acetonitrile after matrix hydration based on the amount of co-extracts and recoveries performance. During clean-up procedure, primary-secondary amine/graphitized carbon black (500 mg was selected, which exhibited outstanding properties in clean-up capabilities and recoveries of pesticides comparing to primary-secondary amine/graphitized carbon black (250 mg, NH2-Carbon and TPT absorbents. The method was validated employing gas chromatography coupled to tandem mass spectrometry at the spiked concentration levels of 0.050 and 0.100 mg kg−1. For most of the targeted pesticides, the percent recoveries range from 70 to 120%, with relative standard deviations <20%. The linear correlation coefficients (r 2 were higher than 0.99 at concentration levels of 0.025–0.250 mg kg−1. Limits of quantification ranged from 1.1 to 25.3 µg kg−1 for all pesticides. The developed method was successfully applied to the determination of pesticides in tea leaf samples.

  11. Determination of Levels of Organochlorine, Organophosphorus, and Pyrethroid Pesticide Residues in Vegetables from Markets in Dar es Salaam by GC-MS

    Directory of Open Access Journals (Sweden)

    John A. M. Mahugija

    2017-01-01

    Full Text Available This study investigated the levels of pesticides and metabolites in vegetables from major markets in Dar es Salaam city, Tanzania. Samples of fresh cabbage, spinach, and onions from the markets were analysed for pesticide residues. Extraction was performed using acetone followed by dichloromethane : cyclohexane mixture and the extracts were cleaned up using Florisil. The compounds were determined by gas chromatography-mass spectrometry (GC-MS. Pesticides and metabolites were detected in 72.2% of the samples. The detected pesticide residues and their highest mean concentrations were p,p′-DDT 4.00 × 10−3 mg/kg, p,p′-DDD 6.40 × 10−1 mg/kg, o,p′-DDD 1.00 × 10−2 mg/kg, α-endosulfan 6.00 × 10−1 mg/kg, β-endosulfan 2.10 × 10−1 mg/kg, chlorpyrifos 3.00 mg/kg, and cypermethrin 4.00 × 10−2 mg/kg. The most frequently detected compounds were p,p′-DDD and chlorpyrifos. The order of contamination was spinach > cabbage > onions. Generally, there were no significant variations in concentrations of pesticide residues among samples and sampling sites, which indicated similarities in contamination patterns. The concentrations of contaminants were above the maximum residue limits (MRLs in 33.3–50% of the samples. The findings indicated risks and concerns for public health.

  12. Effect of household and industrial processing on the levels of pesticide residues and degradation products in melons.

    Science.gov (United States)

    Bonnechère, A; Hanot, V; Bragard, C; Bedoret, T; van Loco, J

    2012-01-01

    Two varieties of melons (Cucumis melo) were treated with two fungicides (carbendazim and maneb) and four insecticides (acetamiprid, cyromazin, imazalil and thiamethoxam) to quantify the effect of household processing on the pesticide residues. To ensure sufficiently high levels of residues in flesh and peel, the most concentrated formulations were applied observing good agricultural practice. The peeling step decreased the concentration of pesticide residues for maneb, imazalil and acetamiprid by more than 90%. Cyromazin, carbendazim and thiamethoxam were reduced by approximately 50%. The reduction of the pesticides could not be fully explained by the systemic character of the pesticides. However, the agricultural practices (time of application), solubility and mode of action (systemic versus contact pesticide) of the pesticides could be used to explain the difference in processing factors for the studied pesticides. Degradation products (melamine and ethylenethiourea) were also investigated in this study, but were not detected.

  13. Atomic Level Cleaning of Poly Methyl Methacrylate Residues from the Graphene Surface Using Radiolized Water at High Temperatures (Postprint)

    Science.gov (United States)

    2017-09-05

    AFRL-RX-WP-JA-2017-0321 ATOMIC LEVEL CLEANING OF POLY-METHYL- METHACRYLATE RESIDUES FROM THE GRAPHENE SURFACE USING RADIOLIZED WATER AT...COVERED (From - To) 9 March 2017 Interim 8 September 2014 – 9 February 2017 4. TITLE AND SUBTITLE ATOMIC LEVEL CLEANING OF POLY-METHYL- METHACRYLATE...graphene surfaces and can only provide atomically clean graphene surfaces in areas as large as ˜10-4 µm2. Here, we transfer CVD-grown graphene using

  14. Country-Level Life Cycle Assessment of Greenhouse Gas Emissions from Liquefied Natural Gas Trade for Electricity Generation.

    Science.gov (United States)

    Kasumu, Adebola S; Li, Vivian; Coleman, James W; Liendo, Jeanne; Jordaan, Sarah M

    2018-02-20

    In the determination of the net impact of liquefied natural gas (LNG) on greenhouse gas emissions, life cycle assessments (LCA) of electricity generation have yet to combine the effects of transport distances between exporting and importing countries, country-level infrastructure in importing countries, and the fuel sources displaced in importing countries. To address this, we conduct a LCA of electricity generated from LNG export from British Columbia, Canada with a three-step approach: (1) a review of viable electricity generation markets for LNG, (2) the development of results for greenhouse gas emissions that account for transport to importing nations as well as the infrastructure required for power generation and delivery, and (3) emissions displacement scenarios to test assumptions about what electricity is being displaced in the importing nation. Results show that while the ultimate magnitude of the greenhouse gas emissions associated with natural gas production systems is still unknown, life cycle greenhouse gas emissions depend on country-level infrastructure (specifically, the efficiency of the generation fleet, transmission and distribution losses and LNG ocean transport distances) as well as the assumptions on what is displaced in the domestic electricity generation mix. Exogenous events such as the Fukushima nuclear disaster have unanticipated effects on the emissions displacement results. We highlight national regulations, environmental policies, and multilateral agreements that could play a role in mitigating emissions.

  15. Different Analytical Procedures for the Study of Organic Residues in Archeological Ceramic Samples with the Use of Gas Chromatography-mass Spectrometry.

    Science.gov (United States)

    Kałużna-Czaplińska, Joanna; Rosiak, Angelina; Kwapińska, Marzena; Kwapiński, Witold

    2016-01-01

    The analysis of the composition of organic residues present in pottery is an important source of information for historians and archeologists. Chemical characterization of the materials provides information on diets, habits, technologies, and original use of the vessels. This review presents the problem of analytical studies of archeological materials with a special emphasis on organic residues. Current methods used in the determination of different organic compounds in archeological ceramics are presented. Particular attention is paid to the procedures of analysis of archeological ceramic samples used before gas chromatography-mass spectrometry. Advantages and disadvantages of different extraction methods and application of proper quality assurance/quality control procedures are discussed.

  16. Influence of different disease control pesticide strategies on multiple pesticide residue levels in apple

    DEFF Research Database (Denmark)

    Poulsen, Mette Erecius; Naef, A.; Gasser, S.

    2009-01-01

    Seven pesticide application strategies were investigated to control apple scab (Venturia inaequalis) and powdery mildew (Podosphaera leucotricha) and, at the same time.. fulfil the new quality standards implemented by some German retailers. These demand that pesticide residues should be below 80...

  17. Prediction of hydrodynamic and other solution properties of rigid proteins from atomic- and residue-level models.

    Science.gov (United States)

    Ortega, A; Amorós, D; García de la Torre, J

    2011-08-17

    Here we extend the ability to predict hydrodynamic coefficients and other solution properties of rigid macromolecular structures from atomic-level structures, implemented in the computer program HYDROPRO, to models with lower, residue-level resolution. Whereas in the former case there is one bead per nonhydrogen atom, the latter contains one bead per amino acid (or nucleotide) residue, thus allowing calculations when atomic resolution is not available or coarse-grained models are preferred. We parameterized the effective hydrodynamic radius of the elements in the atomic- and residue-level models using a very large set of experimental data for translational and rotational coefficients (intrinsic viscosity and radius of gyration) for >50 proteins. We also extended the calculations to very large proteins and macromolecular complexes, such as the whole 70S ribosome. We show that with proper parameterization, the two levels of resolution yield similar and rather good agreement with experimental data. The new version of HYDROPRO, in addition to considering various computational and modeling schemes, is far more efficient computationally and can be handled with the use of a graphical interface. Copyright © 2011 Biophysical Society. Published by Elsevier Inc. All rights reserved.

  18. Vacuum stability and residual gas density estimation for the vacuum chamber upgrade of the ATLAS interaction region of the Large Hadron Collider

    CERN Document Server

    Bregliozzi, G; Baglin, V; Jimenez, J M

    2012-01-01

    The CERN Large Hadron Collider (LHC) has 54 km of ultra-high vacuum (UHV) beam chambers out of which about 90% are at cryogenic temperature (1.9 K) and the rest at room temperature. During operation, the residual gas density in the beam pipes is dominated by beam induced effect such ion, electron and photon-stimulated gas desorption. Therefore, the computation of gas density profile is of great importance to confirm the vacuum stability, and to estimate the beam lifetime. Moreover, the gas density profiles are essential to determine the machine induced background in the experimental areas, and to define the pressure profile in the cryogenic sectors where there is no vacuum instrumentation available. In this paper, the vacuum stability is studied for a newly proposed upgrade of the vacuum chamber at the ATLAS interaction point, using the vacuum stability code called VASCO. The residual gas density profile along the ATLAS vacuum chambers and the effects of photon and electron flux hitting the vacuum chamber wal...

  19. The residue levels of narasin in eggs of laying hens fed with unmedicated and medicated feed.

    Science.gov (United States)

    Rokka, Mervi; Eerola, Susanna; Perttilä, Ulla; Rossow, Laila; Venäläinen, Eija; Valkonen, Eija; Valaja, Jarmo; Peltonen, Kimmo

    2005-01-01

    Laying hens were fed contaminated feed containing narasin 2.5 mg/kg for 21 days followed by a 7 day withdrawal period, hens in the control group were fed unmedicated feed. Eggs were collected during trial days 0, 3, 7, 14, 21 and after the withdrawal period of 7 days. The concentration of narasin in yolks and egg whites was analyzed by a liquid chromatography-mass spectrometry method. Narasin was found to accumulate in yolks, where the narasin concentration increased during the treatment. The concentration of narasin varied from 5.9 to 13.8 microg/kg (mean 10.6 microg/kg) in yolks after 21 day feeding periods. The concentrations of narasin ranged from residues were not found in egg whites of the laying hens fed contaminated feed nor in either yolks or egg whites of the laying hens fed unmedicated feed. The effect of cooking was also tested on the amount of narasin residues in eggs. Cooking for 10 min did not significantly influence the narasin residues in eggs. Traces of lasalocid were also found in the yolks. The traces of lasalocid are attributable to an accidental contamination of the feed during its manufacture.

  20. Simulation of Water Level Fluctuations in a Hydraulic System Using a Coupled Liquid-Gas Model

    Directory of Open Access Journals (Sweden)

    Chao Wang

    2015-08-01

    Full Text Available A model for simulating vertical water level fluctuations with coupled liquid and gas phases is presented. The Preissmann implicit scheme is used to linearize the governing equations for one-dimensional transient flow for both liquid and gas phases, and the linear system is solved using the chasing method. Some classical cases for single liquid and gas phase transients in pipelines and networks are studied to verify that the proposed methods are accurate and reliable. The implicit scheme is extended using a dynamic mesh to simulate the water level fluctuations in a U-tube and an open surge tank without consideration of the gas phase. Methods of coupling liquid and gas phases are presented and used for studying the transient process and interaction between the phases, for gas phase limited in a chamber and gas phase transported in a pipeline. In particular, two other simplified models, one neglecting the effect of the gas phase on the liquid phase and the other one coupling the liquid and gas phases asynchronously, are proposed. The numerical results indicate that the asynchronous model performs better, and are finally applied to a hydropower station with surge tanks and air shafts to simulate the water level fluctuations and air speed.

  1. ENTRIA 2014. Memorandum on the disposal of high-level radioactive residuals; ENTRIA 2014. Memorandum zur Entsorgung hochradioaktiver Reststoffe

    Energy Technology Data Exchange (ETDEWEB)

    Roehlig, Klaus-Juergen; Walther, Clemens; Bach, Friedrich-Wilhelm [Niedersaechsische Technische Hochschule, Braunschweig, Clausthal-Zellerfeld, Hannover (Germany); and others

    2014-04-30

    The memorandum on the disposal of high-level radioactive residuals covers the following issues: description of the problem: a ''wicked problem'', risks and NIMBY, the site selection law, international boundary conditions; disposal strategy and types of facilities: safety and reversibility, long-term surface storage, deep storage; risk and safety; procedural justice and the site selection process; social innovations and the requirement of long-term institutions; conclusion - central stress fields.

  2. The level density parameters for fermi gas model

    International Nuclear Information System (INIS)

    Zuang Youxiang; Wang Cuilan; Zhou Chunmei; Su Zongdi

    1986-01-01

    Nuclear level densities are crucial ingredient in the statistical models, for instance, in the calculations of the widths, cross sections, emitted particle spectra, etc. for various reaction channels. In this work 667 sets of more reliable and new experimental data are adopted, which include average level spacing D D , radiative capture width Γ γ 0 at neutron binding energy and cumulative level number N 0 at the low excitation energy. They are published during 1973 to 1983. Based on the parameters given by Gilbert-Cameon and Cook the physical quantities mentioned above are calculated. The calculated results have the deviation obviously from experimental values. In order to improve the fitting, the parameters in the G-C formula are adjusted and new set of level density parameters is obsained. The parameters is this work are more suitable to fit new measurements

  3. Serum Growth Arrest Specific Protein 6 (Gas-6 Levels in Patients with Schizophrenia

    Directory of Open Access Journals (Sweden)

    Fethullah Gerin

    2016-03-01

    Full Text Available Objective: We have investigated serum growth ar­rest-specific protein 6 (GAS-6 levels from patients with schizophrenia divided into acute phase remission phases as well as control group. Methods: This study was conducted in Psychiatry De­partment of Istanbul University Cerrahpasa Medical Fac­ulty. The patients who were diagnosed with schizophrenia after regular psychiatric examination according to DSM-IV criteria (n=22 as well as control subjects were includ­ed in the study. Schizophrenia patients with acute phase and remission phase were evaluated by Positive and Negative Syndrome Scale (PANSS and Clinical global Impression Scale (CGI-S. The serum GAS-6 levels of schizophrenia patients during acute phase and remission phase were compared with the serum GAS-6 levels of healthy controls. Serum GAS-6 levels were measured by commercial ELISA kits. Results: No difference was found in serum GAS-6 levels among the three groups; schizophrenia with acute phase, schizophrenia with remission phase, and controls. There were no correlations between serum GAS-6 levels and PANSS and CGI scores. Conclusion: To reach a definitive data and better in­terpretation about the relationship between GAS-6 and schizophrenia, future studies with larger groups of pa­tients with schizophrenia subdivided by drug naïve and treated with antipsychotics/other treatment modalities and controls are needed.

  4. Analysis of residual crosslinking agent content in UV cross-linked poly(ethylene oxide hydrogels for dermatological application by gas chromatography

    Directory of Open Access Journals (Sweden)

    Rachel Shet Hui Wong

    2016-10-01

    Full Text Available Acrylates have been widely used in the synthesis of pharmaceutical polymers. The quantitation of residual acrylate monomers is vital as they are strong irritants and allergens, but after polymerization, are relatively inert, causing no irritation and allergies. Poly(ethylene oxide (PEO hydrogels were prepared using pentaerythritol tetra-acrylate (PETRA as UV crosslinking agent. A simple, accurate, and robust quantitation method was developed based on gas chromatographic techniques (GC, which is suitable for routine analysis of residual PETRA monomers in these hydrogels. Unreacted PETRA was initially identified using gas chromatography–mass spectrometry (GC–MS. The quantitation of analyte was performed and validated using gas chromatography equipped with a flame ionization detector (GC–FID. A linear relationship was obtained over the range of 0.0002%–0.0450% (m/m with a correlation coefficient (r2 greater than 0.99. The recovery (>90%, intra-day precision (%RSD <0.67, inter-day precision (%RSD <2.5%, and robustness (%RSD <1.62% of the method were within the acceptable values. The limit of detection (LOD and limit of quantitation (LOQ were 0.0001% (m/m and 0.0002% (m/m, respectively. This assay provides a simple and quick way of screening for residual acrylate monomer in hydrogels.

  5. Levels and distribution of pesticide residues in soil and sediments in ...

    African Journals Online (AJOL)

    Analyses of cleaned sample extracts were performed using gas chromatography- ... toxicity and bioaccumulation) most of the organochlorine pesticides were banned in the 1990s and replaced by organophosphorus pesticides, pyrethroids and carbamates which are readily ... for other applications and they function well.

  6. County-level Oil and Gas Production in the U.S.

    Data.gov (United States)

    Department of Agriculture — County-level data from oil and/or natural gas producing States—for onshore production in the lower 48 States only—are compiled on a State-by-State basis. Most States...

  7. Proposed systematic methodology for analysis of Pb-210 radioactivity in residues produced in Brazilian natural gas pipes

    International Nuclear Information System (INIS)

    Ferreira, Aloisio Cordilha

    2003-11-01

    Since the 80's, the potential radiological hazards due to the handling of solid wastes contaminated with Rn-222 long-lived progeny - Pb-210 in special - produced in gas pipes and removed by pig operations have been subject of growing concern abroad our country. Nevertheless, little or no attention has been paid to this matter in the Brazilian plants up to now, being these hazards frequently underestimated or even ignored. The main purpose of this work was to propose a systematic methodology for analysis of Pb-210 radioactivity in black powder samples from some Brazilian plants, through the evaluation of direct Pb-210 gamma spectrometry and Bi-210 beta counting technical viabilities. In both cases, one in five samples of black powder analysed showed relevant activity (above 1Bq/kg) of Pb-210, being these results probably related to particular features of each specific plant (production levels, reservoir geochemical profile, etc.), in such a way that a single pattern is not observed. For the proposed methodology, gamma spectrometry proved to be the most reliable technique, showing a 3.5% standard deviation, and, for a 95% confidence level, overall fitness in the range of Pb-210 concentration of activity presented in the standard sample reference sheet, provided by IAEA for intercomparison purposes. In the Brazilian scene, however, the availability of statistically supported evidences is insufficient to allow the potential radiological hazard due to the management of black powder to be discarded. Thus, further research efforts are recommended in order to detect the eventually critical regions or plants where gas exploration, production and processing practices will require a regular program of radiological surveillance, in the near future. (author)

  8. Tropospheric gas at potentially toxic levels in air

    Science.gov (United States)

    Bhattacharya, Atreyee

    2012-08-01

    Forest fires and emission of air pollutants, such as fumes from vehicles running on diesel and slow burning of coal and charcoal, release isocyanic acid in the troposphere. In 2011, scientists first detected isocyanic acid in the ambient atmosphere at levels toxic to human populations; at concentrations exceeding 1 part per billion by volume (ppbv), human beings could experience tissue decay when exposed to the toxin. For the first time, using a chemical transport model designed to estimate the distribution and budget of isocyanic acid in the troposphere, Young et al. showed that in several parts of the world, local emissions may increase the concentration of isocyanic acid in the ambient atmosphere, thereby exposing large populations to potentially toxic levels of the acid.

  9. Residual radioactive contamination from decommissioning: Technical basis for translating contamination levels to annual dose

    Energy Technology Data Exchange (ETDEWEB)

    Kennedy, W.E. Jr.; Peloquin, R.A. (Pacific Northwest Lab., Richland, WA (USA))

    1990-01-01

    This document describes the generic modeling of the total effective dose equivalent (TEDE) to an individual in a population from a unit concentration of residual radioactive contamination. Radioactive contamination inside buildings and soil contamination are considered. Unit concentration TEDE factors by radionuclide, exposure pathway, and exposure scenario are calculated. Reference radiation exposure scenarios are used to derive unit concentration TEDE factors for about 200 individual radionuclides and parent-daughter mixtures. For buildings, these unit concentration factors list the annual TEDE for volume and surface contamination situations. For soil, annual TEDE factors are presented for unit concentrations of radionuclides in soil during residential use of contaminated land and the TEDE per unit total inventory for potential use of drinking water from a ground-water source. Because of the generic treatment of potentially complex ground-water systems, the annual TEDE factors for drinking water for a given inventory may only indicate when additional site data or modeling sophistication are warranted. Descriptions are provided of the models, exposure pathways, exposure scenarios, parameter values, and assumptions used. An analysis of the potential annual TEDE resulting from reference mixtures of residual radionuclides is provided to demonstrate application of the TEDE factors. 62 refs., 5 figs., 66 tabs.

  10. Residual radioactive contamination from decommissioning: Technical basis for translating contamination levels to annual dose

    International Nuclear Information System (INIS)

    Kennedy, W.E. Jr.; Peloquin, R.A.

    1990-01-01

    This document describes the generic modeling of the total effective dose equivalent (TEDE) to an individual in a population from a unit concentration of residual radioactive contamination. Radioactive contamination inside buildings and soil contamination are considered. Unit concentration TEDE factors by radionuclide, exposure pathway, and exposure scenario are calculated. Reference radiation exposure scenarios are used to derive unit concentration TEDE factors for about 200 individual radionuclides and parent-daughter mixtures. For buildings, these unit concentration factors list the annual TEDE for volume and surface contamination situations. For soil, annual TEDE factors are presented for unit concentrations of radionuclides in soil during residential use of contaminated land and the TEDE per unit total inventory for potential use of drinking water from a ground-water source. Because of the generic treatment of potentially complex ground-water systems, the annual TEDE factors for drinking water for a given inventory may only indicate when additional site data or modeling sophistication are warranted. Descriptions are provided of the models, exposure pathways, exposure scenarios, parameter values, and assumptions used. An analysis of the potential annual TEDE resulting from reference mixtures of residual radionuclides is provided to demonstrate application of the TEDE factors. 62 refs., 5 figs., 66 tabs

  11. Polyethylene encapsulation of molten salt oxidation mixed low-level radioactive salt residues

    International Nuclear Information System (INIS)

    Lageraaen, P.R.; Kalb, P.D.; Grimmett, D.L.; Gay, R.L.; Newman, C.D.

    1995-01-01

    A limited scope treatability study was conducted for polyethylene encapsulation of salt residues generated by a Molten Salt Oxidation (MSO) technology demonstration at the Energy Technology Engineering Center (ETEC), operated by Rockwell International for the US Department of Energy (DOE). During 1992 and 1993, ETEC performed a demonstration with a prototype MSO unit and treated approximately 50 gallons of mixed waste comprised of radioactively contaminated oils produced by hot cell operations. A sample of the mixed waste contaminated spent salt was used during the BNL polyethylene encapsulation treatability study. A nominal waste loading of 50 wt % was successfully processed and waste form test specimens were made for Toxicity Characteristic Leaching Procedure (TCLP) testing. The encapsulated product was compared with base-line TCLP results for total chromium and was found to be well within allowable EPA guidelines

  12. Simple and rapid analysis of residual aminopolyether (K222) levels in [18F]-labeled imaging agents

    International Nuclear Information System (INIS)

    Tang Xiaolan; Liao Wenjie; Tang Ganghua

    2008-01-01

    Aminopolyether (K222) is a commonly used catalyst in the routine preparation of [ 18 F]-labeled tracers as PET imaging agents. Determination of residual K222 levels in [ 18 F]-labeled radiopharmaceuticals is a quality control criterion required before they can be released for human use. However, there is no simple and rapid method for the determination of K222 levels. A universal iodine-vapor TLC stain method was developed for the semiquantitative analysis of K222 levels in [ 18 F]-labeled radiopharmaceuticals in this study. Compared with the spectrophotometry and the potassium permanganate TLC stain approach, the iodine-vapor TLC stain method is simple, rapid, accurate and reliable. It can be used as a routine method for the determination of K222 levels. (authors)

  13. New developments in low-level gas counting of tritium

    International Nuclear Information System (INIS)

    Povinec, P.; Szarka, J.; Usacev, S.; Chudy, M.

    1977-01-01

    The design is described of a proportional counter for low-level counting of soft radiation. The body of the counter is made of a stainless steel pipe 123 mm in dia and 250 mm in length. The outer cathode of the multiple anode ring counter is formed by a stainless steel pipe and the inner cathode is made of molybdenum plated gold wires 1OO μm in dia. The ring anticoincidence counter contains 40 wire anodes 50 μm in diameter. The sensitive volume of the ring counter is 0.7 l. Teflon and plexiglas are used as insulation materials for the counter. The diagram is presented of the decision-making logical digital unit and a block diagram is presented of the pulse shape discrimination system connected to the described counter. The total background of the counter in lead shielding is 3.2O cps. Using internal anticoincidence the background of the counter is reduced to O.35 cps. The final background using concurrent internal and external anticoincidence is 1.O cpm. (J.B.)

  14. Human health risks associated with residual pesticide levels in edible tissues of slaughtered cattle in Benin City, Southern Nigeria

    Directory of Open Access Journals (Sweden)

    Isioma Tongo

    2015-01-01

    Full Text Available Pesticide residues in meat is of growing concern due to possible adverse effects on humans. Pesticide levels were assessed in five edible cattle parts: muscle, liver, kidney and tongue tissues to determine human health risk associated with consumption of these tissues. Health risk estimates were analysed using estimated daily intake (EDI, hazard quotient (HQ and hazard index (HI for two (2 age/weight categories: 1–11years/30 kg for children while 70 kg was used for adult. Risks were categorized for non-carcinogenic and carcinogenic health effects and measured at the average, maximum, 50th and 95th percentiles of the measured exposure concentrations (MEC. Total pesticide residues ranged from 2.38 to 3.86 μg/kg (muscle, 3.58 to 6.3 μg/kg (liver, 1.87 to 4.59 μg/kg (kidney and 2.54 to 4.35 μg/kg (tongue. Residual pesticide concentrations in the tissues were in the order: Liver > Tongue > Muscle > Kidney. The concentrations of all the assessed pesticides observed in the tissues were however lower than the recommended maximum residual limits (MRLs. Human health risk estimations for the children showed EDI values for heptachlor epoxide, aldrin and dieldrin exceeding threshold values. Non-cancer risk posed to children on consumption of contaminated cattle parts showed HQ values for heptachlor epoxide, aldrin, dieldrin and HI values for organochlorines exceeding 1, indicating the possibility of non-carcinogenic health risks to consumers especially children from consumption of cattle meat from the selected abattoirs.

  15. Design and operation of off-gas cleaning systems at high level liquid waste conditioning facilities

    International Nuclear Information System (INIS)

    1988-01-01

    The immobilization of high level liquid wastes from the reprocessing of irradiated nuclear fuels is of great interest and serious efforts are being undertaken to find a satisfactory technical solution. Volatilization of fission product elements during immobilization poses the potential for the release of radioactive substances to the environment and necessitates effective off-gas cleaning systems. This report describes typical off-gas cleaning systems used in the most advanced high level liquid waste immobilization plants and considers most of the equipment and components which can be used for the efficient retention of the aerosols and volatile contaminants. In the case of a nuclear facility consisting of several different facilities, release limits are generally prescribed for the nuclear facility as a whole. Since high level liquid waste conditioning (calcination, vitrification, etc.) facilities are usually located at fuel reprocessing sites (where the majority of the high level liquid wastes originates), the off-gas cleaning system should be designed so that the airborne radioactivity discharge of the whole site, including the emission of the waste conditioning facility, can be kept below the permitted limits. This report deals with the sources and composition of different kinds of high level liquid wastes and describes briefly the main high level liquid waste solidification processes examining the sources and characteristics of the off-gas contaminants to be retained by the off-gas cleaning system. The equipment and components of typical off-gas systems used in the most advanced (large pilot or industrial scale) high level liquid waste solidification plants are described. Safety considerations for the design and safe operation of the off-gas systems are discussed. 60 refs, 31 figs, 17 tabs

  16. Residues in the analyst of the patient's symbiotic connection at a somatic level: unrepresented states in the patient and analyst.

    Science.gov (United States)

    Godsil, Geraldine

    2018-02-01

    This paper discusses the residues of a somatic countertransference that revealed its meaning several years after apparently successful analytic work had ended. Psychoanalytic and Jungian analytic ideas on primitive communication, dissociation and enactment are explored in the working through of a shared respiratory symptom between patient and analyst. Growth in the analyst was necessary so that the patient's communication at a somatic level could be understood. Bleger's concept that both the patient's and analyst's body are part of the setting was central in the working through. © 2018, The Society of Analytical Psychology.

  17. Residue level description of in vivo self-association of Plasmodium falciparum P2.

    Science.gov (United States)

    Mishra, Pushpa; Sharma, Shobhona; Hosur, Ramakrishna V

    2014-04-01

    Plasmodium falciparum P2 (PfP2) is a ribosomal stalk protein. It also performs extra ribosomal novel functions that seem to be associated with homo oligomerization . Previous in vitro studies have demonstrated that the protein has a high tendency to self-associate predominantly into an 8-mer. In vitro Heteronuclear Single Quantum Coherence (HSQC) of the pure recombinant protein (rPfP2) and its in-cell (Escherichia coli) HSQC spectrum has very similar features, indicating that the protein intrinsically, both inside the cell and under in vitro conditions, has similar aggregation tendencies. In view of this, we have characterized here the folding and concomitant self-association of rPfP2, using an in vitro dissociation-association strategy. We observed that the residue stretch, (Met31-Leu44) of the rPfP2, mapping to Met1-Leu14 of PfP2 protein acts as a nucleation site for helix formation and subsequent self-association. Further association appears to be driven by hydrophobic and complimentary electrostatic charge interactions on the surfaces formed. One stretch of rPfP2, (Ile97-Ala116), always remains floppy, and this may serve as "hinge" for protein segmental motions. Based on these, we have proposed a possible model for rPfP2 self-association into an 8-mer.

  18. Residue levels of molinate in rice field soil: their effects on populations of aquatic flora and fauna under recycling and non-recycling practices in the MUDA area

    International Nuclear Information System (INIS)

    Nashriyah Mat; Azimahtol Hawariah Lope Pihie

    2002-01-01

    A study to evaluate the effects of Molinate residue levels in rice field soil on populations of weed and aquatic fauna in the recycling and the non-recycling areas of Muda was carried out. Molinate residue levels in soil, Simpson Index of Diversity and Importance Value (IV) of weeds, and Sequential Comparison Index of aquatic fauna were measured. No marked variation between the recycled (B 111) and non-recycled (D 111) area was observed for the population parameters and residue levels measured. (Author)

  19. Fuel gas production from animal and agricultural residues and biomass. Quarterly coordination meeting, December 11-12, 1978, Denver, Colorado. Second Quarterly progress report

    Energy Technology Data Exchange (ETDEWEB)

    Wise, D L; Ashare, E; Wentworth, R L

    1979-01-05

    The tenth quarterly coordination meeting of the methane production group of the Fuels from Biomass Systems Branch, US Department of Energy was held at Denver, Colorado, December 11-12, 1978. Progress reports were presented by the contractors and a site visit was made to the Solar Energy Research Institute, Golden, Colorado. A meeting agenda, a list of attendees, and progress are presented. Report titles are: pipeline fuel gas from an environmental feedlot; operation of a 50,000 gallon anaerobic digester at the Monroe State Dairy Farm near Monroe, Washington; anaerobic fermentation of livestock and crop residues; anaerobic fermentation of agricultural residues - potential for improvement and implementation; heat treatment of organics for increasing anaerobic biodegradability; and biological conversion of biomass to methane. (DC)

  20. Fast gas chromatographic residue analysis in animal feed using split injection and atmospheric pressure chemical ionisation tandem mass spectrometry.

    Science.gov (United States)

    Tienstra, M; Portolés, T; Hernández, F; Mol, J G J

    2015-11-27

    Significant speed improvement for instrumental runtime would make GC–MS much more attractive for determination of pesticides and contaminants and as complementary technique to LC–MS. This was the trigger to develop a fast method (time between injections less than 10 min) for the determination of pesticides and PCBs that are not (or less) amenable to LC–MS. A key factor in achieving shorter analysis time was the use of split injection (1:10) which allowed the use of a much higher initial GC oven temperature. A shorter column (15 m), higher temperature ramp, and higher carrier gas flow rate (6 mL/min) further contributed to analysis-time reduction. Chromatographic resolution was slightly compromised but still well fit-for-purpose. Due to the high sensitivity of the technique used (GC–APCI-triple quadrupole MS/MS), quantification and identification were still possible down to the 10 μg/kg level, which was demonstrated by successful validation of the method for complex feed matrices according to EU guidelines. Other advantages of the method included a better compatibility of acetonitrile extracts (e.g. QuEChERS) with GC, and a reduced transfer of co-extractants into the GC column and mass spectrometer.

  1. Multi-Level Risk Assessment of a Power Plant Gas Turbine Applying ...

    African Journals Online (AJOL)

    Multi-Level Risk Assessment of a Power Plant Gas Turbine Applying the Criticality Index Model. ... Journal of the Nigerian Association of Mathematical Physics ... This study has carefully shown and expressed a step by step computation of the severity level of the Turbine component parts, using the Criticality Index model.

  2. Persistent organochlorine residues in foodstuffs from Australia, Papua New Guinea and the Solomon Islands: contamination levels and human dietary exposure.

    Science.gov (United States)

    Kannan, K; Tanabe, S; Williams, R J; Tatsukawa, R

    1994-08-15

    Concentrations of polychlorinated biphenyls (PCBs), DDT and its metabolites (DDTs), HCH isomers (HCHs), chlordane compounds (CHLs), aldrin, dieldrin, heptachlor, heptachlor epoxide and HCB were determined in a wide variety of foodstuffs collected from different locations in Australia, Papua New Guinea and the Solomon Islands. Elevated levels of PCBs, CHLs, DDTs and dieldrin were detected in most of the foodstuffs of animal origin. Fish samples collected near the coast of Sydney recorded noticeable concentrations of PCBs, CHLs and DDTs. PCB contamination was generally prominent in samples collected in urban areas, whereas organochlorine pesticides were distributed uniformly throughout Australia. The widespread usage of CHLs was evident from the composition of its compounds in various foods while HCHs and DDTs were found to have been used sporadically in space and time. For the most part, residue levels of organochlorines in foodstuffs were below the tolerance limits established by national and international health organizations. The exception was CHLs in some fish samples, which exceeded the maximum residue limits recommended by the National Health and Medical Research Council of the Australian government. Although the number of samples analysed in each class of foods is small for the purpose of estimating human dietary exposure, we tentatively conclude that the dietary intake of PCBs in Australia was higher than those observed in most developed and developing nations, whereas the intake of organochlorine pesticides was higher than in developed nations but lower than in developing countries. Meat products contributed to the higher dietary intakes of most of the organochlorines. The contamination pattern and the residual concentrations of organochlorines in foodstuffs of Papua New Guinea and the Solomon Islands resembled those observed in Australia.

  3. Detection of residues in urine and tissues of sheep treated with trace levels of dietary ractopamine HCl.

    Science.gov (United States)

    Smith, D J; Shelver, W L; Marx, A

    2016-12-01

    Qualitative assays are sometimes used as the sole basis for detecting drug residues in live animals or in animal products. Such assays have become increasingly sensitive as detection technologies have improved, yet the limitations of such assays to discriminate purposeful and accidental drug exposures remain poorly defined. A study was conducted to determine the ability of a ractopamine lateral flow assay to accurately detect incurred ractopamine residues in contaminated feeds and in sheep fed trace quantities of ractopamine HCl. False positive and negative samples were determined using a quantitative liquid chromatography-tandem mass spectrometric (LC-MS/MS) method. Ractopamine HCl was fed to sheep at 0 (Zero), 1 (Low), 10 (Med), or 100 (High) µg/kg of diet ( = 4 per level, 0.5 kg of feed/d) for 7 consecutive d and urine was collected daily about ∼16 h post exposure. On-site lateral flow assays were able to reliably (0% false negatives) detect 20 μg of ractopamine HCl per kg of feed. Urine from treated sheep tested positive for ractopamine residues by lateral flow assay in 7.4 (Zero), 0 (Low), 82 (Med), and 86% (High) of the urine samples from each group. Parent ractopamine was below the assay limit of quantification (LOQ, 0.7 ng/mL) in all urine samples using LC-MS/MS. After hydrolysis of ractopamine conjugates, total ractopamine (parent + hydrolyzed metabolites) in urine of Low animals was always less than the LOQ, but in 7 of 28 samples were above the limit of detection (LOD, 0.22 ng/mL). In contrast, urine in Med animals contained 1.08 to 9.13 ng/mL of total ractopamine, while urine of High animals contained 4.85-32.82 ng/mL of total ractopamine. Ractopamine is rapidly eliminated; nevertheless, > 80% of urine samples from sheep exposed to 5 µg/d (M) of ractopamine HCl had detectable residues by the screening assay and a 100% of samples had measurable ractopamine using LC-MS/MS methods. Tissue residues of ractopamine were not detected in any of the sheep

  4. Proteomic Investigation of Protein Profile Changes and Amino Acid Residue Level Modification in Cooked Lamb Meat: The Effect of Boiling.

    Science.gov (United States)

    Yu, Tzer-Yang; Morton, James D; Clerens, Stefan; Dyer, Jolon M

    2015-10-21

    Hydrothermal treatment (heating in water) is a common method of general food processing and preparation. For red-meat-based foods, boiling is common; however, how the molecular level effects of this treatment correlate to the overall food properties is not yet well-understood. The effects of differing boiling times on lamb meat and the resultant cooking water were here examined through proteomic evaluation. The longer boiling time was found to result in increased protein aggregation involving particularly proteins such as glyceraldehyde-3-phosphate dehydrogenase, as well as truncation in proteins such as in α-actinin-2. Heat-induced protein backbone cleavage was observed adjacent to aspartic acid and asparagine residues. Side-chain modifications of amino acid residues resulting from the heating, including oxidation of phenylalanine and formation of carboxyethyllysine, were characterized in the cooked samples. Actin and myoglobin bands from the cooked meat per se remained visible on sodium dodecyl sulfate-polyacrylamide gel electrophoresis, even after significant cooking time. These proteins were also found to be the major source of observed heat-induced modifications. This study provides new insights into molecular-level modifications occurring in lamb meat proteins during boiling and a protein chemistry basis for better understanding the effect of this common treatment on the nutritional and functional properties of red-meat-based foods.

  5. COPRED: prediction of fold, GO molecular function and functional residues at the domain level.

    Science.gov (United States)

    López, Daniel; Pazos, Florencio

    2013-07-15

    Only recently the first resources devoted to the functional annotation of proteins at the domain level started to appear. The next step is to develop specific methodologies for predicting function at the domain level based on these resources, and to implement them in web servers to be used by the community. In this work, we present COPRED, a web server for the concomitant prediction of fold, molecular function and functional sites at the domain level, based on a methodology for domain molecular function prediction and a resource of domain functional annotations previously developed and benchmarked. COPRED can be freely accessed at http://csbg.cnb.csic.es/copred. The interface works in all standard web browsers. WebGL (natively supported by most browsers) is required for the in-line preview and manipulation of protein 3D structures. The website includes a detailed help section and usage examples. pazos@cnb.csic.es.

  6. The impact of small scale cogeneration on the gas demand at distribution level

    International Nuclear Information System (INIS)

    Vandewalle, J.; D’haeseleer, W.

    2014-01-01

    Highlights: • Impact on the gas network of a massive implementation of cogeneration. • Distributed energy resources in a smart grid environment. • Optimisation of cogeneration scheduling. - Abstract: Smart grids are often regarded as an important step towards the future energy system. Combined heat and power (CHP) or cogeneration has several advantages in the context of the smart grid, which include the efficient use of primary energy and the reduction of electrical losses through transmission. However, the role of the gas network is often overlooked in this context. Therefore, this work presents an analysis of the impact of a massive implementation of small scale (micro) cogeneration units on the gas demand at distribution level. This work shows that using generic information in the simulations overestimates the impact of CHP. Furthermore, the importance of the thermal storage tank capacity on the impact on the gas demand is shown. Larger storage tanks lead to lower gas demand peaks and hence a lower impact on the gas distribution network. It is also shown that the use of an economically led controller leads to similar results compared to classical heat led control. Finally, it results that a low sell back tariff for electricity increases the impact of cogeneration on the gas demand peak

  7. Effect of the Basic Residue on the Energetics, Dynamics and Mechanisms of Gas- Phase Fragmentation of Protonated Peptides

    Energy Technology Data Exchange (ETDEWEB)

    Laskin, Julia; Yang, Zhibo; Song, Tao; Lam, Corey; Chu, Ivan K.

    2010-11-17

    The effect of the basic residue on the energetics, dynamics and mechanisms of backbone fragmentation of protonated peptides was investigated. Time- and collision energy-resolved surface-induced dissociation (SID) of singly protonated peptides with the N-terminal arginine residue and their analogs, in which arginine is replaced with less basic lysine and histidine residues was examined using in a specially configured Fourier transform ion cyclotron resonance mass spectrometer (FT-ICR MS). SID experiments demonstrated very different kinetics of formation of several primary product ions of peptides with and without arginine residue. The energetics and dynamics of these pathways were determined from the RRKM modeling of the experimental data. Comparison between the kinetics and energetics of fragmentation of arginine-containing peptides and the corresponding methyl ester derivatives provides important information on the effect of dissociation pathways involving salt bridge (SB) intermediates on the observed fragmentation behavior. It is found that because pathways involving SB intermediates are characterized by low threshold energies, they efficiently compete with classical oxazolone pathways of arginine-containing peptides on a long timescale of the FT-ICR instrument. In contrast, fragmentation of histidine- and lysine-containing peptides is largely determined by classical oxazolone pathways. Because SB pathways are characterized by negative activation entropies, fragmentation of arginine-containing peptides is kinetically hindered and observed at higher collision energies as compared to their lysine- and histidine-containing analogs.

  8. Screening of the presence organophosphates and organochlorines pesticide residues in vegetables and fruits using gas chromatography-mass spectrometry

    Science.gov (United States)

    Putri, Dillani; Aryana, Nurhani; Aristiawan, Yosi; Styarini, Dyah

    2017-01-01

    Pesticides is commonly used to improve the quality of agricultural product, especially in vegetables and fruits. Due to pesticide residues in the product become a concern to consumer health, monitoring and analysis of pesticide residues in agriculture product need to be established. The certified reference material (CRM) is often benefited to obtain accurate results in analysis. It is required as the quality control to improve quality assurance of the testing results. Unfortunately in Indonesia, the development of matrix CRM for the analysis of pesticide residues in vegetables and fruits is still limited. This study is aimed to determine the type of commodity and target analyte to be employed in the development of CRM for pesticides in vegetables and fruits. As the preliminary study, the screening of 11 commodities of fresh vegetables and fruits has been conducted to review the information about the presence of organophosphates (OPs) and organochlorines (OCs) in the sample. In this analysis, QuEChERS technique was used in the extraction process and the qualitative analysis was evaluated by using GC-MS. The results showed that strawberry and celery contain residues of pesticide chlorpyrifos. Further analysis of the commodity celery from seven different places has been conducted, resulting that from 3 of all 7 samples (43%) were positive containing chlorpyrifos. Therefore, the development of CRM for chlorpyrifos in celery will be our next research project.

  9. Test Plan for Measuring Ventilation Rates and Combustible Gas Levels in TWRS Active Catch Tanks

    International Nuclear Information System (INIS)

    NGUYEN, D.M.

    2000-01-01

    The purpose of this data collection activity is to obtain data for a screening of combustible gases in catch tanks that are currently operated by the River Protection Project (RPP). The results will be used to support closure of the flammable gas unreviewed safety question for these facilities. The data collection will be conducted in accordance with the ''Tank Safety Screening Data Quality Objective'' (Dukelow et al. 1995). Combustible gas, ammonia, and organic vapor levels in the headspace of the catch tanks will be field-measured using hand-held instruments. If a combustible gas level measurement in a tank exceeds an established threshold, vapor grab samples (i.e., Hoke and SUMMA) will be collected for laboratory analysis. In addition, ventilation rates of some catch tanks will be determine using the tracer gas injection method to evaluate removal of flammable gas by air flowing through the tanks. This test plan identifies the field tests, sample collection, laboratory analysis, quality assurance, and reporting objectives for this data collection effort. The plan also provides step-by-step direction for field measurement of combustible gas concentrations and determination of ventilation rates

  10. Test Plan for Measuring Ventilation Rates and Combustible Gas Levels in TWRS Active Catch Tanks

    International Nuclear Information System (INIS)

    NGUYEN, D.M.

    2000-01-01

    The purpose of this data collection activity is to obtain data for a screening of combustible gases in catch tanks that are currently operated by the River Protection Project (RPP). The results will be used to support closure of the flammable gas unreviewed safety question for these facilities. The data collection will be conducted in accordance with the ''Tank Safety Screening Data Quality Objective'' (Dukelow et a1 1995). Combustible gas, ammonia, and organic vapor levels in the headspace of the catch tanks will be field-measured using hand-held instruments. If a combustible gas level measurement in a tank exceeds an established threshold, vapor grab samples will be collected for laboratory analysis. In addition, ventilation rates of some catch tanks will be determined using the tracer gas injection method to evaluate removal of flammable gas by air flowing through the tanks. This test plan identifies the field tests, sample collection, laboratory analysis, quality assurance, and reporting objectives for this data collection effort. The plan also provides step by-step direction for field measurement of combustible gas concentrations and determination of ventilation rates

  11. High residue levels and the chemical form of mercury in tissues and organs of seabirds

    Energy Technology Data Exchange (ETDEWEB)

    Kim, E.Y.; Murakami, Toru; Saeki, Kazutoshi; Tatsukawa, Ryo [Ehime Univ. (Japan). Dept. of Environment Conservation

    1995-12-31

    Total and organic (methyl) mercury in liver, muscle, kidney and feather of 9 species of seabirds were analyzed to determine the levels and their distribution and to clarify the occurrences of high mercury levels and their detoxification process in seabirds. Total mercury levels in liver showed great variations in intra and interspecies, while organic mercury levels were less variable. As compared with species in relatively low mercury levels, the species which accumulated the high concentration of mercury like black-footed albatross exhibited the different distribution of mercury in the body: in total mercury burden, albatross species contained less than 10% in feather and over 50% in liver, while other species contained over 40% in feather and less than 20% in liver. The order of organic mercury concentrations in tissues were as follows: liver > kidney > muscle in seabirds examined, except oldsquaw. The mean percentage of organic mercury in total was 35%, 66%, and 36% in liver, muscle and kidney, respectively, for all the species. The significant negative correlations were found between organic mercury percentage to total mercury and total mercury concentrations in the liver and muscle of black-footed albatross and in the liver of laysan albatross. Furthermore, in liver, muscle, and kidney of all the species, the percentages of organic mercury had a negative trend with an increase of total mercury concentrations. The results suggest that albatross species may be capable for demethylating organic mercury in the tissues (mainly in liver), and for storing the mercury as immobilizable inorganic form in the liver as substitution for delivering organic mercury to other organs. It is noteworthy that the species with high degree of demethylation showed the lower mercury burdens in feather and slow moulting pattern.

  12. Impact of natural gas extraction on Pah levels in ambient air

    Science.gov (United States)

    Paulik, L. Blair; Donald, Carey E.; Smith, Brian W.; Tidwell, Lane G.; Hobbie, Kevin A.; Kincl, Laurel; Haynes, Erin N.; Anderson, Kim A.

    2015-01-01

    Natural gas extraction, often referred to as “fracking,” has increased rapidly in the U.S. in recent years. To address potential health impacts, passive air samplers were deployed in a rural community heavily affected by the natural gas boom. Samplers were analyzed for 62 polycyclic aromatic hydrocarbons (PAHs). Results were grouped based on distance from each sampler to the nearest active well. PAH levels were highest when samplers were closest to active wells. Additionally, PAH levels closest to natural gas activity were an order of magnitude higher than levels previously reported in rural areas. Sourcing ratios indicate that PAHs were predominantly petrogenic, suggesting that elevated PAH levels were influenced by direct releases from the earth. Quantitative human health risk assessment estimated the excess lifetime cancer risks associated with exposure to the measured PAHs. Closest to active wells, the risk estimated for maximum residential exposure was 2.9 in 10,000, which is above the U.S. EPA's acceptable risk level. Overall, risk estimates decreased 30% when comparing results from samplers closest to active wells to those farthest. This work suggests that natural gas extraction may be contributing significantly to PAHs in air, at levels that are relevant to human health. PMID:25810398

  13. DRY WELLS IN QUADRANT 25, 26 & 30 – GEOCHEMICAL INVESTIGATIONS INTO RESIDUAL OIL & GAS IN DRY WELLS

    OpenAIRE

    Maqbool, Waqas

    2014-01-01

    This thesis represents the findings concerning core samples from 15 examined exploration wells (with a total of 91 samples) on the eastern flank of the Viking Graben, North Sea, that were classified as dry by NPD (meaning no discovery of oil and gas). These samples were studied using geochemical methodology and analytical methods to evaluate if there might exist the remains of migrated oil or gas. Sample selection at NPD was based on apparent coloration or staining of the sandstone cores. The...

  14. Gas generation from low-level radioactive waste: Concerns for disposal

    International Nuclear Information System (INIS)

    Siskind, B.

    1992-01-01

    The Advisory Committee on Nuclear Waste (ACNW) has urged the Nuclear Regulatory Commission (NRC) to reexamine the topic of hydrogen gas generation from low-level radioactive waste (LLW) in closed spaces to ensure that the slow buildup of hydrogen from water-bearing wastes in sealed containers does not become a problem for long-term safe disposal. Brookhaven National Laboratory (BNL) has prepared a report, summarized in this paper, for the NRC to respond to these concerns. The paper discusses the range of values for G(H 2 ) reported for materials of relevance to LLW disposal; most of these values are in the range of 0.1 to 0.6. Most studies of radiolytic hydrogen generation indicate a leveling off of pressurization, probably because of chemical kinetics involving, in many cases, the radiolysis of water within the waste. Even if no leveling off occurs, realistic gas leakage rates (indicating poor closure by gaskets on drums and liners) will result in adequate relief of pressure for radiolytic gas generation from the majority of commercial sector LLW packages. Biodegradative gas generation, however, could pose a pressurization hazard even at realistic gas leakage rates. Recommendations include passive vents on LLW containers (as already specified for high integrity containers) and upper limits to the G values and/or the specific activity of the LLW

  15. Development and validation of a stability-indicating gas chromatographic method for quality control of residual solvents in blonanserin: a novel atypical antipsychotic agent.

    Science.gov (United States)

    Peng, Ming; Liu, Jin; Lu, Dan; Yang, Yong-Jian

    2012-09-01

    Blonanserin is a novel atypical antipsychotic agent for the treatment of schizophrenia. Ethyl alcohol, isopropyl alcohol and toluene are utilized in the synthesis route of this bulk drug. A new validated gas chromatographic (GC) method for the simultaneous determination of residual solvents in blonanserin is described in this paper. Blonanserin was dissolved in N, N-dimethylformamide to make a sample solution that was directly injected into a DB-624 column. A postrun oven temperature at 240°C for approximately 2 h after the analysis cycle was performed to wash out blonanserin residue in the GC column. Quantitation was performed by external standard analyses and the validation was carried out according to International Conference on Harmonization validation guidelines Q2A and Q2B. The method was shown to be specific (no interference in the blank solution), linear (correlation coefficients ≥0.99998, n = 10), accurate (average recoveries between 94.1 and 101.7%), precise (intra-day and inter-day precision ≤2.6%), sensitive (limit of detection ≤0.2 ng, and limit of quantitation ≤0.7 ng), robust (small variations of carrier gas flow, initial oven temperature, temperature ramping rate, injector and detector temperatures did not significantly affect the system suitability test parameters and peak areas) and stable (reference standard and sample solutions were stable over 48 h). This extensively validated method is ready to be used for the quality control of blonanserin.

  16. CO2 Biofixation by the Cyanobacterium Spirulina sp. LEB 18 and the Green Alga Chlorella fusca LEB 111 Grown Using Gas Effluents and Solid Residues of Thermoelectric Origin.

    Science.gov (United States)

    da Silva Vaz, Bruna; Costa, Jorge Alberto Vieira; de Morais, Michele Greque

    2016-01-01

    The concentration of carbon dioxide (CO2) in the atmosphere has increased from 280 to 400 ppm in the last 10 years, and the coal-fired power plants are responsible for approximately 22 % of these emissions. The burning of fossil fuel also produces a great amount of solid waste that causes serious industrial and environmental problems. The biological processes become interesting alternative in combating pollution and developing new products. The objective of this study was to evaluate the CO2 biofixation potential of microalgae that were grown using gaseous effluents and solid residues of thermoelectric origin. The microalgae Chlorella fusca LEB 111 presented higher rate of CO2 biofixation (42.8 %) (p Spirulina sp. LEB 18. The values for the CO2 biofixation rates and the kinetic parameters of Spirulina and Chlorella cells grown using combustion gas did not differ significantly from those of cells grown using CO2 and a carbon source in the culture media. These microalgae could be grown using ash derived from coal combustion, using the minerals present in this residue as the source of the essential metals required for their growth and the CO2 derived from the combustion gas as their carbon source.

  17. Pesticide residues in locally available cereals and vegetables

    International Nuclear Information System (INIS)

    Cunanan, S.A.; Santos, F.L.; Bonoan, L.S.

    1976-03-01

    Vegetable samples (pechay, cabbage, lettuce, green beans and tomatoes) bought from public markets in the Metro Manila area were analyzed for pesticide residues using gas chromatography. The samples analyzed in 1968-69 contained high levels of chlorinated pesticides such as DDT, Aldrin, Endrin, and Thiodan, while in the samples analyzed in January 1976, no chlorinated and organophosphate pesticides were detected. Cereal samples (rice, corn and sorghum) were obtained from the National Grains Authority and analyzed for pesticide residues and bromine residues. Total bromine residues was determined by neutron activation analysis. In most of the samples analyzed, the concentrations of pesticide residues were below the tolerance levels set by the FAO/WHO Committee on Pesticide Residues in Foods. An exception was one rice sample from Thailand, the bromine residue content (110ppm) of which exceeds the tolerance level of 50ppm

  18. Determination of pesticide residues in leafy vegetables at parts per billion levels by a chemometric study using GC-ECD in Cameron Highlands, Malaysia.

    Science.gov (United States)

    Farina, Yang; Abdullah, Md Pauzi; Bibi, Nusrat; Khalik, Wan Mohd Afiq Wan Mohd

    2017-06-01

    A simple and sensitive analytical method has been developed employing gas chromatography coupled with electron capture detector (GC-ECD), and validated for screening and quantification of 15 pesticide residues at trace levels in cabbage, broccoli, cauliflower, lettuce, celery, spinach, and mustard. The method consists of two steps, first, to determine the significance of each factor by Pareto chart followed by optimization of these significant factors using central composite design (CCD). Minitab statistical software was used for these multivariate experiments for the generation of 2 4-1 design and CCD matrices. The method evaluation was done by external standard calibration with linearity range between 0.5 and 3mg/kg, with correlation coefficient 0.99, limit of detection (LOD) ranges between 0.02 and 4.5ng/g, and limit of quantification (LOQ) ranges between 0.2 and 45ng/g. The average recovery was between 60% and 128%, with RSD 0.2-19.8%. The method was applied on real vegetable samples from Cameron Highlands. Copyright © 2016 Elsevier Ltd. All rights reserved.

  19. Circulating microRNA levels predict residual beta cell function and glycaemic control in children with type 1 diabetes mellitus

    DEFF Research Database (Denmark)

    Samandari, Nasim; Mirza, Aashiq H.; Nielsen, Lotte B.

    2017-01-01

    from the Danish Remission Phase Cohort, and profiled for miRNAs. At the same time points, meal-stimulated C-peptide and HbA1c levels were measured and insulin-dose adjusted HbA1c (IDAA1c) calculated. miRNAs that at 3 months after diagnosis predicted residual beta cell function and glycaemic control...... in this subgroup were further validated in the remaining cohort (n = 83). Statistical analysis of miRNA prediction for disease progression was performed by multiple linear regression analysis adjusted for age and sex. Results: In the discovery analysis, six miRNAs (hsa-miR-24-3p, hsa-miR-146a-5p, hsa-miR-194-5p...

  20. Allowable residual contamination levels of radionuclides in soil from pathway analysis

    International Nuclear Information System (INIS)

    Nyquist, J.E.; Baes, C.F. III.

    1987-01-01

    The uncertainty regarding radionuclide distributions among Remedial Action Program (RAP) sites and long-term decommissioning and closure options for these sites requires a flexible approach capable of handling different levels of contamination, dose limits, and closure scenarios. We identified a commercially available pathway analysis model, DECOM, which had been used previously in support of remedial activities involving contaminated soil at the Savannah River Plant. The DECOM computer code, which estimates concentrations of radionuclides uniformly distributed in soil that correspond to an annual effective dose equivalent, is written in BASIC and runs on an IBM PC or compatible microcomputer. We obtained the latest version of DECOM and modified it to make it more user friendly and applicable to the Oak Ridge National Laboratory (ORNL) RAP. Some modifications involved changes in default parameters or changes in models based on approaches used by the EPA in regulating remedial actions for hazardous substances. We created a version of DECOM as a LOTUS spreadsheet, using the same models as the BASIC version of DECOM. We discuss the specific modeling approaches taken, the regulatory framework that guided our efforts, the strengths and limitations of each approach, and areas for improvement. We also demonstrate how the LOTUS version of DECOM can be applied to specific problems that may be encountered during ORNL RAP activities. 18 refs., 2 figs., 3 tabs

  1. Evaluation of the 14C-prochloraz residue levels in irradiated mangoes (Mangifera indica) and apples (Malus domestica)

    International Nuclear Information System (INIS)

    Costa, Maria Aparecida

    1998-01-01

    The Brazilian crops mangoes and apples has expanding in the last years. However, tropical fruits crops are susceptible to infection that harms the crop yield. The control of these diseases is made through fungicides such as prochloraz which possesses protecting eradicating action by controlling anthracnose in mangoes and scabies in apples. Agrochemicals are of great importance in the agriculture considering the of relationship cost/benefit. However they may cause a series of problems in the ecosystem, being the levels of agrochemicals residues in fruits one of these factors. The aim of this work was to evaluate the prochloraz levels in mangoes treated in both stages of pre and post harvest, and in apples treated in the pre harvest. In the treatment of the mangoes, the interaction, fungicide with the gamma radiation with dose of 1,0 kGy, was used to induce prochloraz degradation. Treated post harvest mangoes were stored, at 12 deg C during 21 days. The results showed that the prochloraz did not present reduction in the residual levels of the mangoes after 21 day storage, that is the safe period established by the Brazilian legislation on agrochemicals, in treated mangoes. The refrigerated storage (12 deg C) and the gamma radiation also did not contribute to the degradation of the fungicide in mangoes. In average the concentration of the fungicide prochloraz in the peels (bar X = 1,64 mug/g) was higher than in the mangoes pulp (bar x = 0,06 mug/g), which allows the consumption of this fruit, since the peel is always discarded. The degradation product, formed in peels of mangoes in fruits treated in the pre and post harvest was the metabolite BIS 44596; for mangoes treated in the pre-post harvest the metabolite formed was the BIS 445186. Both metabolites were found in very low levels, confirming that occurs degradation of the fungicide in mangoes. In apples treated with the prochloraz, reduction of 500/0 in the levels. (author)

  2. A Novel Acoustic Liquid Level Determination Method for Coal Seam Gas Wells Based on Autocorrelation Analysis

    Directory of Open Access Journals (Sweden)

    Ximing Zhang

    2017-11-01

    Full Text Available In coal seam gas (CSG wells, water is periodically removed from the wellbore in order to keep the bottom-hole flowing pressure at low levels, facilitating the desorption of methane gas from the coal bed. In order to calculate gas flow rate and further optimize well performance, it is necessary to accurately monitor the liquid level in real-time. This paper presents a novel method based on autocorrelation function (ACF analysis for determining the liquid level in CSG wells under intense noise conditions. The method involves the calculation of the acoustic travel time in the annulus and processing the autocorrelation signal in order to extract the weak echo under high background noise. In contrast to previous works, the non-linear dependence of the acoustic velocity on temperature and pressure is taken into account. To locate the liquid level of a coal seam gas well the travel time is computed iteratively with the non-linear velocity model. Afterwards, the proposed method is validated using experimental laboratory investigations that have been developed for liquid level detection under two scenarios, representing the combination of low pressure, weak signal, and intense noise generated by gas flowing and leakage. By adopting an evaluation indicator called Crest Factor, the results have shown the superiority of the ACF-based method compared to Fourier filtering (FFT. In the two scenarios, the maximal measurement error from the proposed method was 0.34% and 0.50%, respectively. The latent periodic characteristic of the reflected signal can be extracted by the ACF-based method even when the noise is larger than 1.42 Pa, which is impossible for FFT-based de-noising. A case study focused on a specific CSG well is presented to illustrate the feasibility of the proposed approach, and also to demonstrate that signal processing with autocorrelation analysis can improve the sensitivity of the detection system.

  3. Impact of Natural Gas Appliances on Pollutant Levels in California Homes

    Energy Technology Data Exchange (ETDEWEB)

    Mullen, Nasim A.; Li, Jina; Singer, Brett C.

    2012-12-01

    This report presents results from the first year of a 2-year study, investigating associations of five air pollutants (CO, NO2, NOX, formaldehyde and acetaldehyde) with the presence of natural gas appliances in California homes. From November 2011 to March 2012, pollutant concentration and occupant activity data were collected in 155 homes for 6-day periods. The sample population included both single-family (68%) and multi-family (32%) dwellings, with 87% having at least one gas appliance and 77% having an unvented gas cooking appliance. The geometric mean (GM) NO2 levels measured in the kitchen, bedroom and outside of homes were similar at values of 15, 12 and 11 ppb, respectively. In contrast, the GM NOx levels measured in the kitchen and bedroom of homes were much higher than levels measured outdoors, at levels of 42 and 41 ppb, compared to 19 ppb, respectively. Roughly 10% of sampled homes had 6-day average NO2 levels that exceeded the outdoor annual average limit set by the California Ambient Air Quality Standards (CAAQS) (30 ppb). The GMs of the highest 1-h and 8-h CO level measured in homes were 2.5 and 1.1 ppm, respectively. Four homes had a 1-h or 8-h concentration that exceeded the outdoor limits set by the CAAQS. The GM formaldehyde and acetaldehyde concentrations measured in homes were 15 and 7 ppb, respectively. Roughly 95% of homes had average formaldehyde levels indoors that exceeded the Chronic Reference Exposure Level set by the California EPA (7 ppb). Concentrations of NO2 and NOx, and to a lesser extent CO were associated with use of gas appliances, particularly unvented gas cooking appliances. Based on first principles, it is expected that effective venting of cooking pollutant emissions at the source will lead to a reduction of pollutant concentrations. However, no statistical association was detected between kitchen exhaust fan use and pollutant concentrations in homes in this study where gas cooking occurred frequently. The lack of

  4. Effects of Cholesterol Levels on Mortality in Patients with Long-Term Peritoneal Dialysis Based on Residual Renal Function

    Directory of Open Access Journals (Sweden)

    Yen-Chung Lin

    2018-03-01

    Full Text Available The effect of dyslipidemia on peritoneal dialysis (PD patients based on the presence of residual renal function (RRF; renal creatinine clearance >2 mL/min/1.73 m2 is unknown. Data from the Taiwan Renal Registry Data System between 2005 and 2012 were analyzed to estimate the association between dyslipidemia and mortality in PD patients. Long-term PD patients (n = 8032 were divided into groups with (RRF; n = 2691, 33.5% and without RRF (non-RRF; n = 5341, 66.5%. The primary outcome was three-year mortality, and multivariate Cox regression was used for survival analysis. After stratifying the total cholesterol (TC level between the first and third years, the hazard ratio for mortality was estimated. In the non-RRF group, TC < 120 mg/dL was associated with independently increased risk of mortality. In the RRF group, low TC was not independently correlated with increased mortality, but TC > 285 mg/dL was associated with increased risk. PD patients with higher level of TC (>200 mg/dL in both first and third years of dialysis had significantly lower risk of mortality. In this nationwide cohort study, PD patients without RRF who had low TC level had the highest mortality, in contrast to those with RRF. Malnutrition in long-term PD patients without RRF is an important issue to be monitored.

  5. Hydrogen gas alleviates oxygen toxicity by reducing hydroxyl radical levels in PC12 cells.

    Directory of Open Access Journals (Sweden)

    Junchao Yu

    Full Text Available Hyperbaric oxygen (HBO therapy through breathing oxygen at the pressure of above 1 atmosphere absolute (ATA is useful for varieties of clinical conditions, especially hypoxic-ischemic diseases. Because of generation of reactive oxygen species (ROS, breathing oxygen gas at high pressures can cause oxygen toxicity in the central nervous system, leading to multiple neurological dysfunction, which limits the use of HBO therapy. Studies have shown that Hydrogen gas (H2 can diminish oxidative stress and effectively reduce active ROS associated with diseases. However, the effect of H2 on ROS generated from HBO therapy remains unclear. In this study, we investigated the effect of H2 on ROS during HBO therapy using PC12 cells. PC12 cells cultured in medium were exposed to oxygen gas or mixed oxygen gas and H2 at 1 ATA or 5 ATA. Cells viability and oxidation products and ROS were determined. The data showed that H2 promoted the cell viability and inhibited the damage in the cell and mitochondria membrane, reduced the levels of lipid peroxidation and DNA oxidation, and selectively decreased the levels of •OH but not disturbing the levels of O2•-, H2O2, or NO• in PC12 cells during HBO therapy. These results indicated that H2 effectively reduced •OH, protected cells against oxygen toxicity resulting from HBO therapy, and had no effect on other ROS. Our data supported that H2 could be potentially used as an antioxidant during HBO therapy.

  6. High-resolution diffraction for residual stress determination in the NiCrMoV wheel of an axial compressor for a heavy-duty gas turbine

    Science.gov (United States)

    Rogante, M.; Török, G.; Ceschini, G. F.; Tognarelli, L.; Füzesy, I.; Rosta, L.

    2004-07-01

    The wheel of an axial compressor for a heavy-duty gas turbine has been investigated for residual stresses (RS) evaluation of the teeth-section where SANS measurements have previously been performed. Such a component can contain internal RS, either due to the manufacturing process, or to the operating cycles fatigue. The constitutive material is a NiCrMoV steel to ASTM A 471 (type 2) norms (equivalent to B50A420B10); this material is usually adopted in the manufacturing of forged components for gas turbines. Internal radial and hoop RS have been determined, whose values are under the limit of 200kPa. Hoop RS, in general, resulted in higher value than the radial ones. The present experiment represents a particularly important step in the RS determination for gas turbine components, since the measurements reveal that the fatigue of the wheel is also a lifetime limiting factor although, in the same technological field, the available data in the actual neutron techniques literature mainly concern turbine buckets.

  7. High-resolution diffraction for residual stress determination in the NiCrMoV wheel of an axial compressor for a heavy-duty gas turbine

    International Nuclear Information System (INIS)

    Rogante, M.; Toeroek, G.; Ceschini, G.F.; Tognarelli, L.; Fuezesy, I.; Rosta, L.

    2004-01-01

    The wheel of an axial compressor for a heavy-duty gas turbine has been investigated for residual stresses (RS) evaluation of the teeth-section where SANS measurements have previously been performed. Such a component can contain internal RS, either due to the manufacturing process, or to the operating cycles fatigue. The constitutive material is a NiCrMoV steel to ASTM A 471 (type 2) norms (equivalent to B50A420B10); this material is usually adopted in the manufacturing of forged components for gas turbines. Internal radial and hoop RS have been determined, whose values are under the limit of 200 kPa. Hoop RS, in general, resulted in higher value than the radial ones. The present experiment represents a particularly important step in the RS determination for gas turbine components, since the measurements reveal that the fatigue of the wheel is also a lifetime limiting factor although, in the same technological field, the available data in the actual neutron techniques literature mainly concern turbine buckets

  8. System-level modeling for economic evaluation of geological CO2 storage in gas reservoirs

    International Nuclear Information System (INIS)

    Zhang, Yingqi; Oldenburg, Curtis M.; Finsterle, Stefan; Bodvarsson, Gudmundur S.

    2007-01-01

    One way to reduce the effects of anthropogenic greenhouse gases on climate is to inject carbon dioxide (CO 2 ) from industrial sources into deep geological formations such as brine aquifers or depleted oil or gas reservoirs. Research is being conducted to improve understanding of factors affecting particular aspects of geological CO 2 storage (such as storage performance, storage capacity, and health, safety and environmental (HSE) issues) as well as to lower the cost of CO 2 capture and related processes. However, there has been less emphasis to date on system-level analyses of geological CO 2 storage that consider geological, economic, and environmental issues by linking detailed process models to representations of engineering components and associated economic models. The objective of this study is to develop a system-level model for geological CO 2 storage, including CO 2 capture and separation, compression, pipeline transportation to the storage site, and CO 2 injection. Within our system model we are incorporating detailed reservoir simulations of CO 2 injection into a gas reservoir and related enhanced production of methane. Potential leakage and associated environmental impacts are also considered. The platform for the system-level model is GoldSim [GoldSim User's Guide. GoldSim Technology Group; 2006, http://www.goldsim.com]. The application of the system model focuses on evaluating the feasibility of carbon sequestration with enhanced gas recovery (CSEGR) in the Rio Vista region of California. The reservoir simulations are performed using a special module of the TOUGH2 simulator, EOS7C, for multicomponent gas mixtures of methane and CO 2 . Using a system-level modeling approach, the economic benefits of enhanced gas recovery can be directly weighed against the costs and benefits of CO 2 injection

  9. Application of Gas Chromatography Coupled to Quadrupole-Orbitrap Mass Spectrometry for Pesticide Residue Analysis in Cereals and Feed Ingredients.

    Science.gov (United States)

    Tienstra, Marc; Mol, Hans G J

    2018-03-01

    A method for residue analysis of pesticides and polychlorinated biphenyls in cereals and feed ingredients based on QuEChERS extraction, programmed temperature vaporizer large-volume injection, and GC with electron ionization (EI) quadrupole Orbitrap full-scan high-resolution MS (60 000 full width at half-maximum at m/z 200) has been developed. In addition to full-scan acquisition, simultaneous full-scan and selected-ion monitoring acquisition was used to improve detectability in incidental cases in which analytes coeluted with intense signals from coextractants. The method was successfully validated down to 10 µg/kg for a single commodity (wheat) using matrix-matched calibration, and for multiple-feed matrixes using standard addition. Identification according to European Union requirements was achieved in >90% of the analyte/matrix combinations, and suggestions for further increasing identification rates have been made. Performance characteristics were compared to an existing method for residue analysis based on GC with EI tandem MS (triple quadrupole).

  10. Detecting Pesticide Residue by Using Modulating Temperature Over a Single SnO2-Based Gas Sensor

    Directory of Open Access Journals (Sweden)

    Zengliang Yu

    2003-09-01

    Full Text Available A new rapid detecting method (called dynamic measurements was reported to detect and distinguish the presence of two pesticide gases in the ambient atmosphere. The method employed only a single SnO2-based gas sensor in a rectangular temperature mode to perform the qualitative analysis of a binary gas mixture (acephate and trichlorphon in air. Polar plots was used for quantitative analysis which the feature extraction was performed by FFT. Experimental results showed that high selectivity of the sensor achieved in the range of 250~3000C and modulating frequency 20mHz, one can easily observe the qualitative difference among the response to pure acephate and trichlorphon gases of the same concentration and to the mixture, and the concentration of pesticide gases can be obtained based on the changes of polar plots.

  11. Multiple fault detection and diagnosis in a gas turbine using nonlinear principal component analysis and structured residuals

    OpenAIRE

    Rincon-Charris, Amilcar; Quevedo Casín, Joseba Jokin

    2013-01-01

    Multiple fault detection and diagnosis is a challenging problem because the number of candidates grows exponentially in the number of faults. In add ition, multiple faults in dynamic systems may be hard to detect, because they can mask or compensate each other’s effects. This paper presents the study of the detection and diagnosis of multiple faults in a SR-30 Gas Turbine using nonlinear principal component analys is as the detection method and structured residua...

  12. Gas

    International Nuclear Information System (INIS)

    1996-01-01

    The French government has decided to modify the conditions of extension of local natural gas authorities to neighbouring districts. The European Union is studying the conditions of internal gas market with the objective of more open markets although considering public service requirements

  13. Determination of leveled costs of electric generation for gas plants, coal and nuclear

    International Nuclear Information System (INIS)

    Alonso V, G.; Palacios H, J.C.; Ramirez S, J.R.; Gomez, A.

    2005-01-01

    The present work analyzes the leveled costs of electric generation for different types of nuclear reactors known as Generation III, these costs are compared with the leveled costs of electric generation of plants with the help of natural gas and coal. In the study several discount rates were used to determine their impact in the initial investment. The obtained results are comparable with similar studies and they show that it has more than enough the base of the leveled cost the nuclear option it is quite competitive in Mexico. Also in this study it is also thinks about the economic viability of a new nuclear power station in Mexico. (Author)

  14. Effects of different levels of sunflower residue silage replacement with alfalfa hay on Azari male buffalo calves fattening performance

    Directory of Open Access Journals (Sweden)

    S. Razzagzadeh

    2010-02-01

    Full Text Available An experiment was conducted to study the effects of replacing alfalfa hay with different levels of sunflower residual silage (SRS on fattening performance of Azari male buffalo calves. Thirty calves with 138.33 Kg of BW fed experimental diets in a completely randomized design with 5 groups and 6 replicates. The five groups (1, 2, 3, 4 and 5 included 0 (control, 25, 50, 75 and 100 percent replacement of alfalfa hay with SRS, respectively in basal diet. The results showed that dry matter intake (DMI was significantly different between the groups (p<0.05. The highest and the lowest DMI were shown at the groups 1 and 5, respectively, however there was no significant difference between the groups 2, 3, and 4 with control. Daily weight gain (DWG was significantly different between the groups (p<0.05. Group 5 had significantly lower DWG than groups 1, 2 and 3, furthermore there were no significant difference between groups 1, 2, 3 and 4. Feed conversion ratio (FCR was significantly different among the groups (p<0.05. There was no significant difference among the groups 1, 2, 3 and 4. But these groups had significantly better FCR than the group 5. The best FCR was obtained for group3. It may conclude that alfalfa hay can be substituted with SRS at 50 % level with no negative effects on Azari male buffalo calves fattening performance.

  15. Detection of pyridaben residue levels in hot pepper fruit and leaves by liquid chromatography-tandem mass spectrometry: effect of household processes.

    Science.gov (United States)

    Kim, Sung-Woo; Abd El-Aty, A M; Rahman, Md Musfiqur; Choi, Jeong-Heui; Choi, Ok-Ja; Rhee, Gyu-Seek; Chang, Moon-Ik; Kim, Heejung; Abid, Morad D N; Shin, Sung Chul; Shim, Jae-Han

    2015-07-01

    Following quick, easy, cheap, effective, rugged and safe (QuEChERS) and LC/MS/MS analysis, pyridaben residual levels were determined in unprocessed and processed hot pepper fruit and leaves. The linearities were satisfactory with determination coefficients (R(2)) in excess of 0.995 in processed and unprocessed pepper fruit and leaves. Recoveries at various concentrations were 79.9-105.1% with relative standard deviations ≤15%. The limits of quantitation of 0.003-0.012 mg/kg were very low compared with the maximum residue limits (2-5 mg/kg) set by the Ministry of Food and Drug Safety, Republic of Korea. The effects of various household processes, including washing, blanching, frying and drying under different conditions (water volume, blanching time and temperature) on residual concentrations were evaluated. Both washing and blanching (in combination with high water volume and time factor) significantly reduced residue levels in hot pepper fruit and leaves compared with other processes. In sum, the developed method was satisfactory and could be used to accurately detect residues in unprocessed and processed pepper fruit and leaves. It is recommended that pepper fruit/leaves be blanched after washing before being consumed to protect consumers from the negative health effects of detected pesticide residues. Copyright © 2014 John Wiley & Sons, Ltd.

  16. Determination of pesticide residues and related compounds in water and industrial effluent by solid-phase extraction and gas chromatography coupled to triple quadrupole mass spectrometry.

    Science.gov (United States)

    Martins, Manoel L; Donato, Filipe F; Prestes, Osmar D; Adaime, Martha B; Zanella, Renato

    2013-09-01

    Pollution of drinking water supplies from industrial waste is a result of several industrial processes and disposal practices, and the establishment of analytical methods for monitoring organic compounds related to environmental and health problems is very important. In this work, a method using solid-phase extraction (SPE) and gas chromatography coupled to triple quadrupole tandem mass spectrometry (GC-QqQ-MS/MS) was developed and validated for the simultaneous determination of pesticide residues and related compounds in drinking and surface water as well as in industrial effluent. Optimization of the method was achieved by using a central composite design approach on parameters such as the sample pH and SPE eluent composition. A single SPE consisting of the loading on a polymeric sorbent of 100 mL of sample adjusted to pH 3 and elution with methanol/methylene chloride (10:90, v/v) permitted the obtaining of acceptable recoveries in most cases. The concentration factor associated with sensitivity of the chromatographic analysis permitted the achievement of the method limit of detection values between 0.01 and 0.25 μg L(-1). Recovery assays presented mean recoveries between 70 and 120% for most of the compounds with very good precision, despite the different chemical nature of the compounds analyzed. The selectivity of the method, evaluated through the relative intensity of quantification and qualification ions obtained by GC-QqQ-MS/MS, was considered adequate. The developed method was finally applied to the determination of target analytes in real samples. River water and treated industrial effluent samples presented residues of some compounds, but no detectable residues were found in the drinking water samples evaluated.

  17. Determination of 1,2-dibromoethane, 1,4-dichlorobenzene and naphthalene residues in honey by gas chromatography--mass spectrometry using purge and trap thermal desorption extraction.

    Science.gov (United States)

    Tananaki, Chrisoula; Zotou, Anastasia; Thrasyvoulou, Andreas

    2005-08-12

    A highly sensitive method for the determination of 1,2-dibromoethane, 1,2-dichlorobenzene and naphthalene residues in honey was developed, using gas chromatography-mass spectrometry combined with a purge and trap thermal desorption system as the extraction technique. Optimal conditions for isolation and separation were established and calibration curves were constructed. Linearity was held between 2.4 and 300 microg kg(-1) honey for 1,2-dibromoethane, 0.5 and 300 microg kg(-1) for 1,4-dichlorobenzene and 0.125 and 3000 microg kg(-1) for naphthalene. The detection limits were found to be 0.8, 0.15 and 0.05 microg kg(-1) honey for 1,2-dibromoethane, 1,4-dichlorobenzene and naphthalene, respectively. The method was applied to the analysis of 25 Greek honey samples. 1,2-Dibromoethane was not found in the majority of the samples, while only one sample was found to contain both 1,4-dichlorobenzene and naphthalene residues at concentrations exceeding 10 microg kg(-1).

  18. Respiratory mechanics and plasma levels of tumor necrosis factor alpha and interleukin 6 are affected by gas humidification during mechanical ventilation in dogs.

    Directory of Open Access Journals (Sweden)

    Claudia Hernández-Jiménez

    Full Text Available The use of dry gases during mechanical ventilation has been associated with the risk of serious airway complications. The goal of the present study was to quantify the plasma levels of TNF-alpha and IL-6 and to determine the radiological, hemodynamic, gasometric, and microscopic changes in lung mechanics in dogs subjected to short-term mechanical ventilation with and without humidification of the inhaled gas. The experiment was conducted for 24 hours in 10 dogs divided into two groups: Group I (n = 5, mechanical ventilation with dry oxygen dispensation, and Group II (n = 5, mechanical ventilation with oxygen dispensation using a moisture chamber. Variance analysis was used. No changes in physiological, hemodynamic, or gasometric, and radiographic constants were observed. Plasma TNF-alpha levels increased in group I, reaching a maximum 24 hours after mechanical ventilation was initiated (ANOVA p = 0.77. This increase was correlated to changes in mechanical ventilation. Plasma IL-6 levels decreased at 12 hours and increased again towards the end of the study (ANOVA p>0.05. Both groups exhibited a decrease in lung compliance and functional residual capacity values, but this was more pronounced in group I. Pplat increased in group I (ANOVA p = 0.02. Inhalation of dry gas caused histological lesions in the entire respiratory tract, including pulmonary parenchyma, to a greater extent than humidified gas. Humidification of inspired gases can attenuate damage associated with mechanical ventilation.

  19. Respiratory mechanics and plasma levels of tumor necrosis factor alpha and interleukin 6 are affected by gas humidification during mechanical ventilation in dogs.

    Science.gov (United States)

    Hernández-Jiménez, Claudia; García-Torrentera, Rogelio; Olmos-Zúñiga, J Raúl; Jasso-Victoria, Rogelio; Gaxiola-Gaxiola, Miguel O; Baltazares-Lipp, Matilde; Gutiérrez-González, Luis H

    2014-01-01

    The use of dry gases during mechanical ventilation has been associated with the risk of serious airway complications. The goal of the present study was to quantify the plasma levels of TNF-alpha and IL-6 and to determine the radiological, hemodynamic, gasometric, and microscopic changes in lung mechanics in dogs subjected to short-term mechanical ventilation with and without humidification of the inhaled gas. The experiment was conducted for 24 hours in 10 dogs divided into two groups: Group I (n = 5), mechanical ventilation with dry oxygen dispensation, and Group II (n = 5), mechanical ventilation with oxygen dispensation using a moisture chamber. Variance analysis was used. No changes in physiological, hemodynamic, or gasometric, and radiographic constants were observed. Plasma TNF-alpha levels increased in group I, reaching a maximum 24 hours after mechanical ventilation was initiated (ANOVA p = 0.77). This increase was correlated to changes in mechanical ventilation. Plasma IL-6 levels decreased at 12 hours and increased again towards the end of the study (ANOVA p>0.05). Both groups exhibited a decrease in lung compliance and functional residual capacity values, but this was more pronounced in group I. Pplat increased in group I (ANOVA p = 0.02). Inhalation of dry gas caused histological lesions in the entire respiratory tract, including pulmonary parenchyma, to a greater extent than humidified gas. Humidification of inspired gases can attenuate damage associated with mechanical ventilation.

  20. Residual deposits (residual soil)

    International Nuclear Information System (INIS)

    Khasanov, A.Kh.

    1988-01-01

    Residual soil deposits is accumulation of new formate ore minerals on the earth surface, arise as a result of chemical decomposition of rocks. As is well known, at the hyper genes zone under the influence of different factors (water, carbonic acid, organic acids, oxygen, microorganism activity) passes chemical weathering of rocks. Residual soil deposits forming depends from complex of geologic and climatic factors and also from composition and physical and chemical properties of initial rocks

  1. Multi-residue method for detecting coccidiostats at carry-over level in feed by HPLC-MS/MS.

    Science.gov (United States)

    Delahaut, Ph; Pierret, G; Ralet, N; Dubois, M; Gillard, N

    2010-06-01

    A multi-residue HPLC-ESI-MS/MS method has been developed for the simultaneous extraction, detection and confirmation of the 11 coccidiostats referenced by Regulation 2009/8/EC (lasalocid sodium, narasin, salinomycin sodium, monensin sodium, semduramicin sodium, maduramicin ammonium alpha, robenidine hydrochloride, decoquinate, halofuginone hydrobromide, nicarbazin, and diclazuril) in feedstuffs at carry-over level. The sensitivity of the method allows quantification and confirmation for all coccidiostats below target concentration. The method was in-house validated and meets all criteria of European legislation (2002/657/EC). The precision of the method was determined under repeatability and within-laboratory reproducibility conditions; RSD(r) and RSD(R) were below the maximum permitted values for every tested concentration. The specificity was checked by analysing representative blank samples and blank samples fortified with potentially interfering substances (benzimidazoles, corticosteroides, triphenylmethane dyes, quinolones, nitrofurans, nitroimidazoles, phenicols); no interference were found. Concerning quantification, a quadratic regression model was fitted to every calibration curve with a regression coefficient r2 above 0.99 on each data set. Finally, the expanded uncertainty U was calculated with data obtained within the laboratory while applying the method during validation and in routine tests.

  2. Allowable residual contamination levels for decommissioning the 115-F and 117-F facilities at the Hanford Site

    International Nuclear Information System (INIS)

    Kennedy, W.E. Jr.; Napier, B.A.

    1983-07-01

    This report contains the results of a study sponsored by UNC Nuclear Industries to determine Allowable Residual Contamination Levels (ARCL) for the 115-F and 117-F facilities at the Hanford Site. The purpose of this study is to provide data useful to UNC engineers in conducting safety and cost comparisons for decommissioning alternatives. The ARCL results are based on a scenario/exposure-pathway analysis and compliance with an annual dose limit for three specific modes of future use of the land and facilities. These modes of use are restricted, controlled, and unrestricted. Information on restricted and controlled use is provided to permit a full consideration of decommissioning alternatives. Procedures are presented for modifying the ARCL values to accommodate changes in the radionuclide mixture or concentrations and to determine instrument responses for various mixtures of radionuclides. Finally, a comparison is made between existing decommissioning guidance and the ARCL values calculated for unrestricted release of the 115-F and 117-F facilities. The comparison shows a good agreement

  3. Environmental performance, mechanical and microstructure analysis of concrete containing oil-based drilling cuttings pyrolysis residues of shale gas.

    Science.gov (United States)

    Wang, Chao-Qiang; Lin, Xiao-Yan; He, Ming; Wang, Dan; Zhang, Si-Lan

    2017-09-15

    The overall objective of this research project is to investigate the feasibility of incorporating oil-based drilling cuttings pyrolysis residues (ODPR) and fly ash serve as replacements for fine aggregates and cementitious materials in concrete. Mechanical and physical properties, detailed environmental performances, and microstructure analysis were carried out. Meanwhile, the early hydration process and hydrated products of ODPR concrete were analyzed with X-ray diffraction (XRD), Fourier transform infrared (FT-IR), scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDX). The results indicated that ODPR could not be categorize into hazardous wastes. ODPR had specific pozzolanic characteristic and the use of ODPR had certain influence on slump and compressive strength of concrete. The best workability and optimal compressive strength were achieved with the help of 35% ODPR. Environmental performance tests came to conclusion that ODPR as recycled aggregates and admixture for the preparation of concrete, from the technique perspective, were the substance of mere environmental contamination. Copyright © 2017 Elsevier B.V. All rights reserved.

  4. System-Level Value of a Gas Engine Power Plant in Electricity and Reserve Production

    Directory of Open Access Journals (Sweden)

    Antti Alahäivälä

    2017-07-01

    Full Text Available Power systems require a certain amount of flexibility to meet varying demand and to be able to cope with unexpected events, and this requirement is expected to increase with the emergence of variable power generation. In this paper, we focus on gas engine power plant technology and the beneficial influence its flexible operation can have on a power system. The study introduces the concept of a combined-cycle gas engine power plant (CCGE, which comprises a combination of several gas-fired combustion engines and a steam turbine. The operation of CCGE is then comprehensively analyzed in electricity and reserve production in the South African power system and compared with combined-cycle gas turbine (CCGT technology. Even though CCGE is a form of technology that has already been commercialized, it is rarely considered as a source of flexibility in the academic research. That is the notion providing the motivation for this study. Our core contribution is to show that the flexibility of CCGE can be valuable in power systems. The methodology is based on the unit-level model of the studied system and the solving of a day-ahead unit commitment problem for each day of the simulated 11-year period. The simulation studies reveal how a CCGE is able to offer system flexibility to follow hourly load variations and capacity to provide reserve power effectively.

  5. Indoor pollutant levels from the use of unvented natural gas fireplaces in Boulder, Colorado.

    Science.gov (United States)

    Dutton, S J; Hannigan, M P; Miller, S L

    2001-12-01

    High CO and NO2 concentrations have been documented in homes with unvented combustion appliances, such as natural gas fireplaces. In addition, polycyclic aromatic hydrocarbons (PAH) are emitted from incomplete natural gas combustion. The acute health risks of CO and NO2 exposure have been well established for the general population and for certain high-risk groups, including infants, the elderly, and people with heart disease or asthma. Health effects from PAH exposure are less well known, but may include increased risk of cancer. We monitored CO emissions during the operation of unvented natural gas fireplaces in two residences in Boulder, CO, at various times between 1997 and 2000. During 1999, we expanded our tests to include measurements of NO2 and PAH. Results show significant pollutant accumulation indoors when the fireplaces were used for extended periods of time. In one case, CO concentrations greater than 100 ppm accumulated in under 2 hr of operation; a person at rest exposed for 10 hr to this environment would get a mild case of CO poisoning with an estimated 10% carboxyhemoglobin level. Appreciable NO2 concentrations were also detected, with a 4-hr time average reaching 0.36 ppm. Similar time-average total PAH concentrations reached 35 ng/m3. The results of this study provide preliminary insights to potential indoor air quality problems in homes operating unvented natural gas fireplaces in Boulder.

  6. Design of a compressed air modulator to be used in comprehensive multidimensional gas chromatography and its application in the determination of pesticide residues in grapes.

    Science.gov (United States)

    Pizzutti, Ionara R; Vreuls, René J J; de Kok, André; Roehrs, Rafael; Martel, Samile; Friggi, Caroline A; Zanella, Renato

    2009-04-10

    In this study, a new modulator that is simple, robust and presents low operation costs, was developed. This modulator uses compressed air to cool two small portions in the first centimeters of the second chromatographic column of a comprehensive multidimensional gas chromatography (GCxGC) system. The results show a variation in the peak area less than 3 and 5% to alkanes and pesticides, respectively. The standard deviations for the retention times in the first and second dimension are around 0.05 min and 0.05s for all the compounds. The system was optimized with n-alkanes. The GCxGC system proposed was applied in the determination of pyrethroid pesticides (bifenthrin, cypermethrin, deltamethrin, fenvalerate, esfenvalerate, cis- and trans-permethrin) in grape samples. Samples were extracted by the mini-Luke modified method and pesticides were quantified by comprehensive multidimensional gas chromatography with micro electron-capture detection (microECD). The values of method limit of quantification (LOQ) were 0.01-0.02 mg kg(-1) for all studied pyrethroid and the values of recovery were between 94.3 and 115.2%, with good precision (RSDcompressed air has the potential for application in the analysis of a wider range of pesticide residues in other commodities since it provides low values of LOQ with acceptable accuracy and precision.

  7. A bi-level programming for multistage co-expansion planning of the integrated gas and electricity system

    DEFF Research Database (Denmark)

    Zeng, Qing; Zhang, Baohua; Fang, Jiakun

    2017-01-01

    This paper focuses on the coordinated expansion planning of the integrated natural gas and electrical power systems with bi-directional energy conversion. Both the Gas-fired Power Generations (GPGs) and Power-to-Gas stations (P2Gs) are considered as the linkages between the natural gas and electric...... as the generation capacities, while the lower-level is formulated as an optimal economic dispatch under the operational constraints given by the upper-level decision. To solve the bi-level multi-stage programming problem, a hybrid algorithm is proposed combining the modified binary particle swarm optimization (BPSO......) and the interior point method (IPM). The BPSO is used for the upper-level sub-problem, and the IPM is adopted for the lower-level sub-problem. Numerical case studies have been carried out on the practical gas and electricity transmission network in western Denmark. Simulation results demonstrate the effectiveness...

  8. Rapid analytical method for the determination of pesticide residues in sunflower seeds based on focused microwave-assisted Soxhlet extraction prior to gas chromatography-tandem mass spectrometry.

    Science.gov (United States)

    Prados-Rosales, R C; Luque García, J L; Luque de Castro, M D

    2003-04-18

    A rapid analytical method for determination of organochlorine pesticide residues in sunflower seeds based on focused microwave-assisted Soxhlet extraction has been developed. The main factors affecting the extraction efficiency--namely microwave power, irradiation time, volume of extractant and number of cycles--were optimized by a two-level factorial fractional design. After extraction, a liquid-liquid extraction and a clean-up step including the use of Florisil macrocolumns were required prior to injection of the extracts into the chromatograph in order to isolate the pesticide residues from the lipid fraction of the original extract. The MS-MS ion preparation mode was selected due to the high sensitivity and selectivity it provides. Seed samples were used collected near a crop subjected to aerial pesticide application. Residues of hexachlorocyclohexane isomers and endosulfan were found in the seeds although they were not subjected to pesticide application, thus showing the spray-drift contamination. The validation of the proposed approach was carried out by comparison with the ISO 659-1988 reference extraction method obtaining similar, or even better efficiencies by the proposed approach.

  9. Detection of Residual Levels and Associated Health Risk of Seven Pesticides in Fresh Eggplant and Tomato Samples from Narayanganj District, Bangladesh

    Directory of Open Access Journals (Sweden)

    Md. Nur Alam

    2015-01-01

    Full Text Available Residual levels of seven frequently used pesticides were investigated in 140 samples of two common vegetables, eggplants and tomatoes, from agricultural fields in the Narayanganj district of Bangladesh. The analysis of pesticide residues was performed by high-performance liquid chromatography with photodiode array detection. A large percentage of the eggplants (50% and tomatoes (60% from the Narayanganj district were contaminated with pesticides, and all of the levels were above the maximum residual limit (MRL proposed by the EC regulation. Diazinon was the most common (35% pesticide detected in the vegetable samples at a concentration of 45–450 times higher than the MRL. The health risk index for diazinon was highest for both eggplant and tomato samples, which may be due to its physiochemical properties. Fenitrothion and linuron are the two second most common types of pesticides detected in the vegetable samples. Regular monitoring of the use of common pesticides on vegetables should be conducted.

  10. Assessment of microbial processes on gas production at radioactive low-level waste disposal sites

    International Nuclear Information System (INIS)

    Weiss, A.J.; Tate, R.L. III; Colombo, P.

    1982-05-01

    Factors controlling gaseous emanations from low level radioactive waste disposal sites are assessed. Importance of gaseous fluxes of methane, carbon dioxide, and possible hydrogen from the site, stems from the inclusion of tritium and/or carbon-14 into the elemental composition of these compounds. In that the primary source of these gases is the biodegradation of organic components of the waste material, primary emphasis of the study involved an examination of the biochemical pathways producing methane, carbon dioxide, and hydrogen, and the environmental parameters controlling the activity of the microbial community involved. Initial examination of the data indicates that the ecosystem is anaerobic. As the result of the complexity of the pathway leading to methane production, factors such as substrate availability, which limit the initial reaction in the sequence, greatly affect the overall rate of methane evolution. Biochemical transformations of methane, hydrogen and carbon dioxide as they pass through the soil profile above the trench are discussed. Results of gas studies performed at three commercial low level radioactive waste disposal sites are reviewed. Methods used to obtain trench and soil gas samples are discussed. Estimates of rates of gas production and amounts released into the atmosphere (by the GASFLOW model) are evaluated. Tritium and carbon-14 gaseous compounds have been measured in these studies; tritiated methane is the major radionuclide species in all disposal trenches studied. The concentration of methane in a typical trench increases with the age of the trench, whereas the concentration of carbon dioxide is similar in all trenches

  11. Novel and rapid method for determination of organophosphorus pesticide residues in edible fungus using direct gas purge microsyringe extraction coupled on-line with gas chromatography-mass spectrometry.

    Science.gov (United States)

    Nan, Jingxi; Wang, Juan; Piao, Xiangfan; Yang, Cui; Wu, Xue; Quinto, Maurizio; Li, Donghao

    2015-09-01

    In this work a new analytical method for a rapid and simultaneous determination of 28 organophosphorus pesticides (OPPs) residues in edible fungus using gas purge microsyringe extraction (GP-MSE), coupled with on-line gas chromatography-mass spectrometry (GP-MSE-GC-MS) has been developed and optimized. GP-MSE, a novel gas flow liquid-phase microextraction technique, has been then fruitfully used as innovative and one-step extraction procedure, allowing a direct injection into the gas chromatograph coupled with a mass spectrometry detector (GC-MS) system without any further cleaning step. Once optimized, the GP-MSE-GC-MS analysis procedure showed reproducibility values, resolutions, linear responses, detection and quantification limits that allowed to consider this method suitable for the analysis of the 28 OPPs in real samples. Furthermore, OPP recoveries and the relative standard deviations (RSDs) ranged from 85.26% to 100.21%, and from 1.6% to 6.9%, respectively. This procedure was then used for the analysis of real samples and the obtained results were compared with those of ultrasonic extraction-solid phase extraction. Among the 28 OPPs, 14 of them were found in Lentinus edodes and Enoki mushrooms fungus samples, with a total concentrations of 112.7 and 210.7 μg kg(-1), respectively. This work demonstrated then that GP-MSE-GC-MS provided a highly efficient, solvent-saving, accurate and sensitive quantitative analysis method for a rapid determination of OPPs in edible fungus. Copyright © 2015 Elsevier B.V. All rights reserved.

  12. Collimator system for the stabilization of the dynamical residual-gas pressure in the heavy-ion synchrotron SIS18; Kollimatorsystem zur Stabilisierung des dynamischen Restgasdruckes im Schwerionensynchrotron SIS18

    Energy Technology Data Exchange (ETDEWEB)

    Omet, Carsten

    2009-01-15

    In order to achieve higher beam intensities of heavy ion beams in ring accelerators, low charge state ions can be used. By lowering the charge state, the space charge limit is shifted to higher particle numbers and stripping losses can be avoided. During test operation of the SIS18 at GSI with high intensity low charge state heavy ion beams, strong intensity dependent beam losses have been observed. It was found that these beam losses are originated to a large extent by the change of charge state of the circulating ions during collisions with residual gas atoms. The resulting deviation of m/q relative to the reference ion leads, in combination with dispersive elements in the ion optic lattice, to a modified trajectory, followed by the loss of the ion on the beam pipe. At the impact position, loosely bound residual gas molecules are released by ion stimulated desorption which increases the residual gas pressure locally. This pressure rise itself enhances the charge exchange rate, which can develop into a self amplifying process of pressure rise and subsequent beam loss. A method for the stabilization of the dynamic residual gas pressure is the use of special catcher systems, which minimize the production of desorption gases and remove them by strong pumping. Therefore, the pressure on the beam axis should remain as stable as possible. Other processes, e.g. Coulomb scattering of the beam ions by residual gas particles and unavoidable systematic beam losses can increase the gas pressure additionally. The pressure in the accelerator is further subjected to ionization of the residual gas atoms themselves, thermal out gassing of the beam pipes, insertions and pumps. In this work, a detailed numerical model of the interplay between the residual gas pressure dynamics in the accelerator, possible stabilization measures, e.g. by catchers and the resulting beam life time has been developed. The forecasted beam life times and pressures are verified by machine experiments, as

  13. On possibility of using E, H - crossed fields and gas-dynamic flowing of argon in the processes of degassing by the method of ion-stimulated desorption of residual gas in the KUTI-20

    International Nuclear Information System (INIS)

    Sharapov, V.E.

    1985-01-01

    In the project considered if the possibility to use the degassing of an adhezatior chamber inner walls, using the method of ion-stimulated desorption (ISD) of residual gas in the glow discharge is considered. It is suggested that the experiment should be realized using the model or the KUTI (PKUTI) prototype to decrease operation pressure to p -7 Pa (2x10 -9 Tor) at the expense of introduction of the technology described and certain modifications in the processes of leak-in and pumping. The use of crossed E,H-fields and gasodynamic regime of argon flow in the process of preliminary degassing of the adhezator chamber by the glow discharge is the main idea of the project

  14. Influence of post-harvest application rates of cyprodinil, treatment time and temperature on residue levels and efficacy in controlling green mould on 'Valencia' oranges.

    Science.gov (United States)

    Schirra, Mario; D'Aquino, Salvatore; Cabras, Paolo; Angioni, Alberto

    2009-07-01

    The effectiveness of heat treatments with water and cyprodinil in controlling post-harvest green mould caused by Penicillium digitatum was investigated on artificially inoculated 'Valencia' oranges. Residue levels of cyprodinil were determined in the oranges as a function of active ingredient concentration, temperature and treatment time. Cyprodinil residues were significantly dependent on treatment time when applied at 600 mg l(-1) and 20 degrees C, but not when fruit were treated at 150-300 mg l(-1). The application of cyprodinil at 50 or 100 mg l(-1) at 55 degrees C for 30 s produced similar residue levels, while residues increased when the application rate was 150 mg l(-1). Cyprodinil at 100 mg l(-1) and 60 degrees C produced a significant increase in residues compared to treatment at 50 mg l(-1); no significant increase in residues was found when the application rate was raised from 100 to 150 mg l(-1). In comparison to treatments performed at 20 degrees C, the application of a heated cyprodinil mixture resulted in significantly higher residues in fruit. All treatments with cyprodinil at 20 degrees C similarly reduced green mould after 7 days of storage at 20 degrees C. After 18 days, treatment with cyprodinil at 600 mg l(-1) for 30 s was more effective than at 150-300 mg l(-1). When dip time was extended to 90 or 180 s, treatment efficacy was positively related to fungicide concentration. Treatments with water at 55 degrees C for 30 s were as effective as cyprodinil at 50-100 mg l(-1), but less effective than cyprodinil at 150 mg l(-1). After 7 days, treatment with water or cyprodinil at 50-150 mg l(-1) and 60 degrees C were equally effective in controlling green mould; while, after 18 days, treatment with cyprodinil at 150 mg l(-1) was consistently more effective than at 50-100 mg l(-1) or hot water alone.

  15. Inversion of double-difference measurements from optical levelling for the Groningen gas field

    Directory of Open Access Journals (Sweden)

    P. A. Fokker

    2015-11-01

    Full Text Available Hydrocarbon extraction lead to compaction of the gas reservoir which is visible as subsidence on the surface. Subsidence measurements can therefore be used to better estimate reservoir parameters. Total subsidence is derived from the result of the measurement of height differences between optical benchmarks. The procedure from optical height difference measurements to absolute subsidence is an inversion, and the result is often used as an input for consequent inversions on the reservoir. We have used the difference measurements directly to invert for compaction of the Groningen gas reservoir in the Netherlands. We have used a linear inversion exercise to update an already existing reservoir compaction model of the field. This procedure yielded areas of increased and decreased levels of compaction compared to the existing compaction model in agreement with observed discrepancies in porosity and aquifer activity.

  16. Levelized Costs for Nuclear, Gas and Coal for Electricity, under the Mexican Scenario

    International Nuclear Information System (INIS)

    Palacios, J.C.; Alonso, G.; Ramirez, R.; Gomez, A.; Ortiz, J.; Longoria, L.C.

    2004-01-01

    In the case of new nuclear power stations, it is necessary to pay special attention to the financial strategy that will be applied, time of construction, investment cost, and the discount and return rate. The levelized cost quantifies the unitary cost of the electricity (the kWh) generated during the lifetime of the nuclear power plant; and allows the immediate comparison with the cost of other alternative technologies. The present paper shows levelized cost for different nuclear technologies and it provides comparison among them as well as with gas and coal electricity plants. For the calculations we applied our own methodology to evaluate the levelized cost considering investment, fuel and operation and maintenance costs, making assumptions for the Mexican market, and taking into account the gas prices projections. The study also shows comparisons using different discount rates (5% and 10%), and some comparisons between our results and an OECD 1998 study. The results are i n good agreement and shows that nuclear option is cost competitive in Mexico on the basis of levelized costs

  17. Levelized Costs for Nuclear, Gas and Coal for Electricity, under the Mexican Scenario

    Energy Technology Data Exchange (ETDEWEB)

    Palacios, J.C.; Alonso, G.; Ramirez, R.; Gomez, A.; Ortiz, J.; Longoria, L.C.

    2004-10-06

    In the case of new nuclear power stations, it is necessary to pay special attention to the financial strategy that will be applied, time of construction, investment cost, and the discount and return rate. The levelized cost quantifies the unitary cost of the electricity (the kWh) generated during the lifetime of the nuclear power plant; and allows the immediate comparison with the cost of other alternative technologies. The present paper shows levelized cost for different nuclear technologies and it provides comparison among them as well as with gas and coal electricity plants. For the calculations we applied our own methodology to evaluate the levelized cost considering investment, fuel and operation and maintenance costs, making assumptions for the Mexican market, and taking into account the gas prices projections. The study also shows comparisons using different discount rates (5% and 10%), and some comparisons between our results and an OECD 1998 study. The results are i n good agreement and shows that nuclear option is cost competitive in Mexico on the basis of levelized costs.

  18. Effects of post-disposal gas generation in a repository for spent fuel, high-level waste and long-lived intermediate level waste sited in opalinus clay

    International Nuclear Information System (INIS)

    Johnson, L.; Marschall, P.; Zuidema, P.; Gribi, P.

    2004-07-01

    This comprehensive report issued by the Swiss National Cooperative for the Disposal of Radioactive Waste NAGRA takes a look at post-disposal gas generation in a repository for spent fuel and highly radioactive wastes in Opalinus clay strata. This study provides a comprehensive treatment of the issue of gas generation in a repository for spent fuel (SF), vitrified high-level waste (HLW) and long-lived intermediate-level waste (ILW), sited in the Opalinus clay of the Zuercher Weinland in northern Switzerland. The issue of how gas generation in and transport from waste repositories may influence disposal system performance has been under study for many years, both at Nagra and internationally. The report consists of three main parts: (i) A synthesis of basic information on the host rock and on details of repository construction; (ii) A discussion on gas transport characteristics of the engineered barrier system and the geosphere; (iii) A discussion on the effects of gas on system performance, based on the available information on gas generation, gas transport properties and gas pathways provided in the previous parts of the report. Simplified model calculations based on a mass balance approach for the gas generated within the repository are presented and discussed

  19. Chemical Composition, in vitro Digestibility and Fermentative Gas Production of Kochia scoparia Irrigated by Water Containing Different Level of Salinity

    Directory of Open Access Journals (Sweden)

    reza valizadeh

    2016-11-01

    al. 1991. Procedure of in vitro gas production was performed according to Menke and Steingass (1988. Rumen fluid was obtained from three fistulated Baluchi male lamb before morning feeding. The DM degradation data were fitted to the exponential equation p = a + b (1 - e-ct. The in vitro dry matter, NDF and organic matter digestibility were determined according to the Arroquy et al (2005 procedure. Test samples were incubated for different hrs and then filtered through the nylon cloth with the pore size of 44microns. The remaining materials were dried at 60 °C for 72 hrs and utilized for the subsequent analysis according to the procedure. In vitro gas production was completed according to the procedure described by Menke and Steingass (1988. Each sample, both original forages and insoluble residues, weighing about 200mg, were put into 100ml calibrated glass syringes (FORTUNA®, Häberle Labortechnik, Germany together with 30ml rumen liquid media solution on a 1:2 ratio. Syringes were incubated in a water bath at 39°C, where a transparent plastic lid with holes held the syringes upright. Two blanks and a standard hay sample of known gas production were included in each run. Results and Discussion NDF content of Kochia scoparia without salinity (irrigate with tap water was higher than that for Kochia samples irrigated with various levels of salinity. Crude protein (CP content of the control Kochia sample (11% was significantly (p

  20. Application of acetone acetals as water scavengers and derivatization agents prior to the gas chromatographic analysis of polar residual solvents in aqueous samples.

    Science.gov (United States)

    van Boxtel, Niels; Wolfs, Kris; Van Schepdael, Ann; Adams, Erwin

    2015-12-18

    The sensitivity of gas chromatography (GC) combined with the full evaporation technique (FET) for the analysis of aqueous samples is limited due to the maximum tolerable sample volume in a headspace vial. Using an acetone acetal as water scavenger prior to FET-GC analysis proved to be a useful and versatile tool for the analysis of high boiling analytes in aqueous samples. 2,2-Dimethoxypropane (DMP) was used in this case resulting in methanol and acetone as reaction products with water. These solvents are relatively volatile and were easily removed by evaporation enabling sample enrichment leading to 10-fold improvement in sensitivity compared to the standard 10μL FET sample volumes for a selection of typical high boiling polar residual solvents in water. This could be improved even further if more sample is used. The method was applied for the determination of residual NMP in an aqueous solution of a cefotaxime analogue and proved to be considerably better than conventional static headspace (sHS) and the standard FET approach. The methodology was also applied to determine trace amounts of ethylene glycol (EG) in aqueous samples like contact lens fluids, where scavenging of the water would avoid laborious extraction prior to derivatization. During this experiment it was revealed that DMP reacts quantitatively with EG to form 2,2-dimethyl-1,3-dioxolane (2,2-DD) under the proposed reaction conditions. The relatively high volatility (bp 93°C) of 2,2-DD makes it possible to perform analysis of EG using the sHS methodology making additional derivatization reactions superfluous. Copyright © 2015 Elsevier B.V. All rights reserved.

  1. Multi-residue method for the determination of organochlorine pesticides in fish feed based on a cleanup approach followed by gas chromatography-triple quadrupole tandem mass spectrometry.

    Science.gov (United States)

    Nardelli, Valeria; dell'Oro, Daniela; Palermo, Carmen; Centonze, Diego

    2010-07-23

    A multi-residue method for the determination of organochlorine pesticides in fish feed samples was developed and optimized. The method is based on a cleanup step of the extracted fat, carried out by liquid-liquid extraction on diatomaceous earth cartridge with n-hexane/acetonitrile (80/20, v/v) followed by solid phase extraction (SPE) with silica gel-SCX cartridge, before the identification and quantification of the residues by gas chromatography-triple quadrupole tandem spectrometry (GC-MS/MS). Performance characteristics, such as accuracy, precision, linear range, limits of detection (LOD) and quantification (LOQ), for each pesticide were determined. Instrumental LODs ranged from 0.01 to 0.11 microg L(-1), LOQs were in the range of 0.02-0.35 microg L(-1), and calibration curves were linear (r2>0.999) in the whole range of explored concentrations (5-100 microg L(-1)). Repeatability values were in the range of 3-15%, evaluated from the relative standard deviation of six samples spiked at 100 microg kg(-1) of fat, and in compliance with that derived by the Horwitz's equation. No matrix effects or interfering substances were observed in fish feed analyses. The proposed method allowed high recoveries (92-116%) of spiked extracted fat samples at 100 microg kg(-1), and very low LODs (between 0.02 and 0.63 microg kg(-1)) and LOQs (between 0.05 and 2.09 microg kg(-1)) determined in fish feed samples. Copyright (c) 2010 Elsevier B.V. All rights reserved.

  2. [Monitoring of the residue of fosthiazate in water samples using solid-phase extraction coupled with gas chromatography/mass spectrometry].

    Science.gov (United States)

    Zhu, Jing; Zhou, Xin; Fu, Chunmei; Liu, Sankang; Li, Zhangwan

    2004-11-01

    Solid-phase extraction (SPE) coupled with gas chromatography/mass spectrometry (GC/MS) was used to determine the fosthiazate residue in water samples. The water samples were first filtered through cellulose filters (0.45 microm pore size). A 100 mL volume of filtered water, in which 1 mL of methanol has been added, was then passed through a pre-conditioned 3 cm C18 cartridge at a flow-rate of 1.5 mL/min. Elution was performed by 1 mL of methanol. The eluant was finally dried under reduced pressure for solvent evaporation. The volume was quantitatively adjusted to 0.5 mL with methanol. The analysis was carried out on GC/MS. The mass spectrometer was operated in selected ion monitoring (SIM) mode. According to mass spectrum of fosthiazate, three selected ions at m/z of 126, 195, 283, respectively, were monitored for identification and quantification. High sensitivity and selectivity were achieved by using this method. The limit of detection for fosthiazate in water samples was determined to be 56.4 ng/L. The linearity was demonstrated over a wide range of concentrations covering from 0.282 to 141 microg/L. The recoveries were more than 85.5% and the relative standard deviations for the overall procedure were less than 4.42%. The fosthiazate residue was detected in the water samples from a pool near cropland where fosthiazate was used. The results demonstrate the suitability of the SPE-GC/MS approach for the analysis of fosthiazate in water.

  3. The technology level of modular devices in outfitting an oil and gas complex in Western Siberia

    Energy Technology Data Exchange (ETDEWEB)

    Berezin, V.L.; Permikin, Yu.N.; Sannikov, Yu.V.; Telegin, L.G.

    1984-01-01

    The status of the problem of ensuring the technology level of modular devices (BKU) is analyzed. It is shown that insufficient consideration in design of the specific production, transport and assembly and operational specifications on the technology level is the cause for creation of irrational designs for modular devices and additional expenditures on their realization. A methodology for controlling the technology level of modular devices being designed is described, which increases the effectiveness of their use (in outfitting petroleum pumping stations (NPS), one of the most important elements of the oil and gas complex). A numerical method for designing the technological structures of the modular devices and an algorithm which ensures practical realization of the method on a computer (EVM) are examined.

  4. New Look at odorization levels for propane gas. [Ethyl mercaptan; thiophane; equilibrium K values

    Energy Technology Data Exchange (ETDEWEB)

    Whisman, M.L.; Goetzinger, J.W.; Cotton, F.O.; Brinkman, D.W.; Thompson, C.J.

    1977-09-01

    Nearly 4,000 persons participated in a study to evaluate three odorant systems in four test modes and at 24 different test sites. Participants included trained panels, untrained ERDA employees, and several thousand untrained volunteer evaluators. The classical testing technique and three modified test modes were used to represent a spectrum of conditions that would define the effect of environmental familiarity and mental distractions upon olfactory responses to LP-gas. Significant efforts were directed toward determination of odorant levels that not only can be detected but also will be detected. The study showed that in addition to defects of the nasal anatomy, psychological factors also affect olfactory responses, and that unfamiliarity with a given environment as well as anxieties or mental distractions can produce reduced awareness to odorants intended to warn individuals of the presence of LP-gas. A second part of the study involved a laboratory determination of equilibrium K-values for both ethyl mercaptan and thiophane at three temperatures. Novel sample handling and gas chromatographic techniques provided reproducible results which were in close agreement with theoretical predictions. (28 tables, 29 tables)

  5. Deep eutectic solvent based gas-assisted dispersive liquid-phase microextraction combined with gas chromatography and flame ionization detection for the determination of some pesticide residues in fruit and vegetable samples.

    Science.gov (United States)

    Farajzadeh, Mir Ali; Sattari Dabbagh, Masoumeh; Yadeghari, Adeleh

    2017-05-01

    In this study, a gas-assisted dispersive liquid-phase microextraction method using a deep eutectic solvent as the extraction solvent combined with gas chromatography and flame ionization detection was developed for the extraction and determination of some pesticide residues in vegetable and fruit juice samples. In this method, choline chloride and 4-chlorophenol at a molar ratio of 1:2 were mixed. By heating and vortexing, a clear, water-immiscible, and homogeneous liquid was formed. The obtained deep eutectic solvent was added to an aqueous solution of the analytes in a conical test tube. Air was bubbled into the aqueous solution and a cloudy solution was obtained. During this step, the analytes were extracted into the fine droplets of the extraction solvent. After centrifugation, an aliquot of the settled phase was injected into the separation system. Under the optimum extraction conditions, enrichment factors, and extraction recoveries were obtained in the ranges of 247-355 and 49-71%, respectively. The obtained values for the limits of detection and quantification were in the ranges of 0.24-1.4 and 0.71-4.2 μg/L, respectively. The proposed method is simple, fast, efficient, and inexpensive. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  6. Gas chromatographic-mass spectrometric determination of levodropropizine plasma levels in healthy volunteers.

    Science.gov (United States)

    Zaratin, P; De Angelis, L; Cattabeni, F

    1988-08-01

    A gas chromatographic-mass spectrometric method for the qualitative and quantitative analysis of levodropropizine (S(-)-3-(4-phenyl-piperazin-1-yl)-propane-1,2-diol, DF 526) in plasma is described. The method proved to be highly selective and sensitive. Drug concentrations as low as 5 ng/ml could be measured. Levodropropizine plasma levels were measured in 6 healthy volunteers after administration of an acute 60 mg dose. Peak concentrations were reached between 40 and 60 min and measurable amounts of drug were present till 8 h after administration.

  7. Novel potentiometric sensors for the determination of the dinotefuran insecticide residue levels in cucumber and soil samples.

    Science.gov (United States)

    Abdel-Ghany, Maha F; Hussein, Lobna A; El Azab, Noha F

    2017-03-01

    Five new potentiometric membrane sensors for the determination of the dinotefuran levels in cucumber and soil samples have been developed. Four of these sensors were based on a newly designed molecularly imprinted polymer (MIP) material consisting of acrylamide or methacrylic acid as a functional monomer in a plasticized PVC (polyvinyl chloride) membrane before and after elution of the template. A fifth sensor, a carboxylated PVC-based sensor plasticized with dioctyl phthalate, was also prepared and tested. Sensor 1 (acrylamide washed) and sensor 3 (methacrylic acid washed) exhibited significantly enhanced responses towards dinotefuran over the concentration range of 10 -7 -10 -2 molL -1 . The limit of detection (LOD) for both sensors was 0.35µgL -1 . The response was near-Nernstian, with average slopes of 66.3 and 50.8mV/decade for sensors 1 and 3 respectively. Sensors 2 (acrylamide non-washed), 4 (methacrylic acid non-washed) and 5 (carboxylated-PVC) exhibited non-Nernstian responses over the concentration range of 10 -7 -10 -3 molL -1 , with LODs of 10.07, 6.90, and 4.30µgL -1 , respectively, as well as average slopes of 39.1, 27.2 and 33mV/decade, respectively. The application of the proposed sensors to the determination of the dinotefuran levels in spiked soil and cucumber samples was demonstrated. The average recoveries from the cucumber samples were from 7.93% to 106.43%, with a standard deviation of less than 13.73%, and recoveries from soil samples were from 97.46% to 108.71%, with a standard deviation of less than 10.66%. The sensors were applied successfully to the determination of the dinotefuran residue, its rate of disappearance and its half-life in cucumbers in soil in which a safety pre-harvest interval for dinotefuran was suggested. Copyright © 2016 Elsevier B.V. All rights reserved.

  8. Assessment of the effect of washing and boiling on the levels of pesticide residues in vegetables cultivated in Akuapem North Municipality

    International Nuclear Information System (INIS)

    Opare-Boafo, Maame Serwa

    2016-07-01

    Vegetables play an important role in human nutrition and health. Pesticides are extensively used by vegetable farmers in crop production and this may contaminate the crop. Traditional method of washing vegetables prior to consumption has been assumed to reduce pesticide residues. The study seeks to assess the effect of washing with various solutions and with boiling on the concentration of pesticide residues in vegetables and to estimate the potential human health risk associated with pesticide ingestion via vegetable diet using the Quick, Easy, Cheap, Effective, Rugged and Safe (QuEChERS) method. Results of the study indicated that the farmers involved in vegetable farming in the Akwapim North Municipality are in the middle age group and use pesticides in their farming activities. Majority (65%) of them have no formal training in pesticide usage and apply pesticides in mixtures made of combinations of up to four (4) pesticides in a single tank mixture. The farmers do not use any protective clothing and stores agrochemicals in multipurpose storage structures together with food containers and farm implements. As a result of pesticide exposure, 67% of farmers experienced various kinds of discomfort including headache, tingling or burning of skin, irritation of eyes or skin. Chloropyrifos residue was the only pesticide residue that gave positive detection in the analysed vegetable samples. The raw (non-spiked) vegetable samples (cabbage, lettuce and squash) had 0.29 mg kg -1 , 0.19 mg kg -1 and 0.14 mg kg -1 of Chloropyrifos residue in cabbage, squash and lettuce respectively. The level of chloropyrifos residues detected in raw cabbage samples from the study area was below the maximum permissible limit (MPLs) of 1 mg/kg (Codex, 2003) but the residues found in raw squash was above the maximum permissible limit of 0.01 mg/kg and that of lettuce was also above the maximum permissible limit (0.05mg/kg). Washing of vegetables vigorously in water for 2 minutes before

  9. LPS levels in root canals after the use of ozone gas and high frequency electrical pulses

    Directory of Open Access Journals (Sweden)

    Tiago André Fontoura de MELO

    2016-01-01

    Full Text Available Abstract The present study aims to verify the effect of ozone gas (OZY® System and high frequency electric pulse (Endox® System systems on human root canals previously contaminated with Escherichia colilipopolysaccharide (LPS. Fifty single-rooted teeth had their dental crowns removed and root lengths standardized to 16 mm. The root canals were prepared up to #60 hand K-files and sterilized using gamma radiation with cobalt 60. The specimens were divided into the following five groups (n = 10 based on the disinfection protocol used: OZY® System, one 120-second-pulse (OZY 1p; OZY® System, four 24-second-pulses (OZY 4p; and Endox® System (ENDOX. Contaminated and non-contaminated canals were exposed only to apyrogenic water and used as positive (C+ and negative (C- controls, respectively. LPS (O55:B55 was administered in all root canals except those belonging to group C-. After performing disinfection, LPS samples were collected from the canals using apyrogenic paper tips. Limulus Amoebocyte Lysate (LAL was used to quantify the LPS levels, and the data obtained was analyzed using one-way ANOVA. The disinfection protocols used were unable to reduce the LPS levels significantly (p = 0.019. The use of ozone gas and high frequency electric pulses was not effective in eliminating LPS from the root canals.

  10. Two-level hierarchical structure in nano-powder agglomerates in gas media

    Science.gov (United States)

    de Martin, Lilian; Bouwman, Wim G.; van Ommen, J. Ruud

    2012-11-01

    Nanoparticles in high concentration in a gas form agglomerates due to the interparticle van der Waals forces. The size and the internal structure of these nanoparticles agglomerates strongly influence their dynamics and their interaction with other objects. This information is crucial, for example, when studying inhalation of nanoparticles. It is common to model the structure of these agglomerates using a fractal approach and to compare their dimension with the dimension obtained from aggregation models, such diffusion limited aggregation (DLA). In this work we have analyzed the structure of nanoparticles agglomerates in situ by means of Spin-Echo Small-Angle Neutron Scattering (SESANS), while they were fluidized in a gas stream. The advantage of SESANS over conventional SANS is that SESANS can measure scales up to 20 microns, while SANS does not exceed a few hundred of nanometers. We have observed that when agglomerates interact, their structure cannot be characterized by using only one scaling parameter, the fractal dimension. We have found that there are at least two structure levels in the agglomerates and hence, we need at least two parameters to describe the autocorrelation function in each level.

  11. Quantifying the Industrial Facility-Level Emission Rate of Methane in Various Segments of the Natural Gas Industry

    Science.gov (United States)

    Herndon, S. C.; Roscioli, J. R.; Yacovitch, T. I.; Floerchinger, C. R.; Mitchell, A.; Tkacik, D. S.; Subramanian, R.; Robinson, A. L.; Martinez, D. M.; Vaughn, T. L.; Williams, L.; Zimmerle, D.; Marchese, A.

    2014-12-01

    Methane, the dominant component in natural gas, is a potent short-lived radiative forcer. Recent technological advances in the extraction of oil and gas have increased the production rate dramatically since early 2000. In the context of CO2 emissions per energy generated, natural gas promises a tantalizing thermodynamic advantage over coal and other hydrocarbons. Natural gas emissions to the atmosphere along the entire path from well to customer, however, can wipe out the radiative forcing advantage once they surpass a threshold fraction of distributed gas. Recent studies have been undertaken to assess the methane emissions at various types of facilities within different sectors of the oil and gas industry. The distribution of observed facility level emission rates along with other results and conclusions from those studies will be presented. The implications that these findings have on the emissions inventories from these sectors will be discussed.

  12. Examination of background contamination levels for gas counting and AMS target preparation in Trondheim

    DEFF Research Database (Denmark)

    Gulliksen, S.; Thomsen, M.S.

    1992-01-01

    conventional gas proportional counting (GPC) system. We have also studied contamination levels of our target preparation for C-14 accelerator mass spectrometry (AMS) dating in Uppsala. A significant lower background is obtained for Icelandic double spar than for marbles, probably due to a crystal structure......The Radiological Dating Laboratory in Trondheim relatively often dates samples with ages >30 ka BP. Contaminated background materials are known to affect the accuracy of very old dates. We have found, by measurements of different materials, that such contamination is small when using our...... of the double spar that is more insensitive to contaminating processes. The background for combusted samples is at the same level as for samples of double spar, indicating that additional C-14 contamination due to combustion is negligible. Dates obtained on interstadial samples (T >30 ka BP) by both GPC and AMS...

  13. GFR and Blood Lead Levels in Gas Station Workers Based on δ-Alad Gene Polymorphisms

    Directory of Open Access Journals (Sweden)

    Lantip Rujito

    2015-04-01

    showed that the proportion of ALAD genotype for ALAD 1-1, 1-2 and 2-2 were 94.7%, 5.3%, and 0% respectively. The mean of serum levels in homozygous 1-1 was 15.94 ppb and heterozygote 1-2 was 1.15 ppb. GFR of participants ranged from 71.11 mL/min to 185.20 mL/min with a mean of 117.34mL/min. There was no correlation between serum Pb and GFR (p = 0.19. Study also could not determine the correlation between GFR and ALAD gene Polymorphism. Discussion: Study then concluded that there was no correlation between blood lead levels in the GFR on each δ-ALAD genotypes. Keywords: Lead intoxication, GFR, δ-ALAD, gas station workers

  14. Gas chromatographic determination of electron capture sensitive volatile industrial chemical residues in foods, using AOAC pesticide multiresidue extraction and cleanup procedures.

    Science.gov (United States)

    Yurawecz, M P; Puma, B J

    1986-01-01

    Electron capture (EC) gas chromatographic (GC) parameters have been developed for determining some of the more volatile industrial chemicals that can be determined by the AOAC multiresidue method for organochlorine and organophosphorus pesticides with modified GC operating conditions. Retention times relative to pentachlorobenzene are reported for 143 industrial chemicals, pesticides, and related compounds on OV-101 GC columns at 130 degrees C. Also reported for most of the compounds are recoveries from fortified samples carried through the AOAC extraction and cleanup procedures for fatty and/or nonfatty foods, Florisil elution characteristics, and GC relative retention times on mixed OV-101 + OV-210 columns at 130 degrees C. Our laboratory has used the modified EC/GC parameters with the AOAC multiresidue extraction/cleanup procedures to determine many volatile halogenated industrial chemical contaminants in foods, chiefly in samples of fresh-water fish. Other modifications of the AOAC method are described to improve the tentative identification and quantitative measurement of these volatile residues.

  15. Determination of the limits of identification and quantitation of selected organochlorine and organophosphorous pesticide residues in surface water by full-scan gas chromatography/mass spectrometry.

    Science.gov (United States)

    Tahboub, Yahya R; Zaater, Mohammad F; Al-Talla, Zeiad A

    2005-12-09

    In this work, we report a reliable method for quantitation and determination of the limits of identification of 14 organochlorine and organophosphorous pesticide (OPP) residues in surface water. The method features the simultaneous identification and quantitation of targeted pesticides and the possibility of identification of any other eluting compounds. The method is based on liquid-liquid extraction (LLE) with a mixture of petroleum ether and dichloromethane (70:30, v/v) followed by gas chromatographic separation and a full-scan mass spectrometric detection (GC-MS). The method presents a new validation parameter, limit of identification (LOI) which is defined for our purpose as the lowest analyte concentration that yields a library searchable mass spectrum. The method is linear over the range 0.048-1.20microgL(-1) for nine pesticides and 0.024-0.60microgL(-1) for the other five pesticides. Correlation coefficients vary between 0.988 and 0.998. Limits of detection (LODs) vary between 0.005 and 0.05microgL(-1) for 4,4'-DDT and LOIs vary between 0.012 and 0.048microgL(-1).

  16. Determination of residual volatile organic compounds migrated from polystyrene food packaging into food simulant by headspace solid phase micro extraction-gas chromatography

    International Nuclear Information System (INIS)

    Mohd Marsin Sanagi; Ling, Susie Lu; Zalilah Nasir; Wan Aini Wan Ibrahim; Abu Naim, Ahmedy

    2008-01-01

    The residual styrene and other volatile organic compounds (VOCs) present in the polystyrene food packaging are of concern as these compounds have the potential to migrate into the food in contact. This work describes a method for quantitative determination of VOCs, namely styrene, toluene, ethyl benzene, iso-propylbenzene and n-propylbenzene that have migrated from polystyrene food packaging into food stimulant by gas chromatography-flame ionization detection (GC-FID). Headspace solid phase micro extraction (HS-SPME) technique was applied for migration test using water as food stimulant. The effects of extraction variables including sample volume, eluotropic strength, extraction temperature, extraction time, desorption time, sample agitation, and salt addition on the amounts of the extracted analyses were studied to obtain the optimal HS-SPME conditions. The optimized method was applied to test the VOCs migrated from polystyrene bowls and cups at storage temperatures ranging from 24 to 80 degree Celsius for 30 min. Styrene and ethyl benzene were found to migrate from the samples into the food stimulant. The migration of analyze was found to be strongly dependent upon the storage temperature. The HS-SPME is useful as an alternative method to determine the migration of VOCs from food packaging material into food stimulant. (author)

  17. A multi-residue method for determination of 70 organic micropollutants in surface waters by solid-phase extraction followed by gas chromatography coupled to tandem mass spectrometry.

    Science.gov (United States)

    Terzopoulou, Evangelia; Voutsa, Dimitra; Kaklamanos, George

    2015-01-01

    A multi-residue method, based on gas chromatography coupled to tandem mass spectrometry (GC-MS/MS), has been developed for the determination of 70 organic micropollutants from various chemical classes (organochlorinated, organophosphorous, triazines, carbamate and urea, polycyclic aromatic hydrocarbons, polychlorinated biphenyls, pharmaceuticals, phenols, etc.) in surface waters. A single-step SPE extraction using OASIS HLB cartridges was employed for the recovery of target micropollutants. The method has been validated according to monitoring performance criteria of the Water Framework Directive, taking into account the approved guidelines on quality assurance and quality control. The recoveries ranged from 60 to 110 %, the coefficient of variation from 0.84 to 27.4 %, and the uncertainty from 6 to 37 %. The LOD varied from 6.0 to 40 ng/L. The limits of quantification for the priority pollutants anthracene, alachlor, atrazine, benzo(a)pyrene, chlorfenvinphos, diuron, isoproturon, nonylphenol, simazine, and terbutryn fulfill the criterion of diuron, isoproturon, salicylic acid, chlorfenvinphos, 1,2-benzanthracene, pyrene, diflubenzuron, and carbaryl exhibited the highest detection frequencies.

  18. Measurement of ampicillin residue levels in chicken eggs during and after medicated feed administration by LC-MS/MS.

    Science.gov (United States)

    Hamamoto, Kouko; Akama, Ryoko; Mizuno, Yasuharu

    2015-01-01

    A simple and sensitive LC-MS/MS method was developed and validated for the determination of ampicillin (ABPC) in chicken eggs. Residues were extracted by reverse-phase solid-phase extraction. Chromatographic separation was performed using a reverse-phase column with an elution gradient. The limits of detection and quantification were 0.01 and 0.1 ng g(-1), respectively. For the 0.1-50 ng g(-1) concentration range, mean recovery and accuracy values were 93.9-98.5% and 100.2-118.0%, respectively. ABPC residue concentrations in eggs before, during and after 7 days of medicated feeding of maximum dosage (40 mg kg(-1) body weight day(-1)) of ABPC were determined with the LC-MS/MS method. The maximum concentration of ABPC in eggs was 3.6 ± 1.7 ng g(-1) (mean ± SD) on the last day of the administration period. Residue concentrations of ABPC in eggs during and after ABPC administration were not over the Japanese maximum residue limit of 0.01 mg kg(-1).

  19. Evaluation of mechanical vibration effect on the residual stresses levels in steel welded joints using an Interface Matlab based on Norm API 579

    Directory of Open Access Journals (Sweden)

    R Rodrigues

    2016-10-01

    Full Text Available Nowadays with the high growth of petrochemical welding technology a great development due to high manufacturing offshore structures, storage tanks of petroleum, boilers and pressure vessels for refining plants have been done. Due to various metallurgical changes and restrictions to contraction and expansion undergone by materials when subjected to welding thermal cycle, internal stresses are generated in welded joint which are nominated residual stresses. It is generally undesirable because it can lead to several problems, such as cracks, cold stress fracture, stress corrosion, among others. Although several studies involving residual stresses have been developed in recent years, few information about the variation of the residual stresses level in welded joints when subjected to stress relief treatment by mechanical vibration have been done. Likewise, there are few information related to the comparison between the degree of efficiency by using the post-weld heat treatment and those treatment. Therefore, the goal of this work was to apply the relieve residual stresses treatment by mechanical vibration in steel welded joints used in oil industry, and compare the results with those obtained by post heat treatment and evaluate the efficiency level of this technique In addition, this works also hope to contribute for a better understanding of this technique and to find which parameters have a greater influence on the results.

  20. Estimating Greenhouse Gas Emissions Level of A Natural Gas Pipeline – Case Study from A to B Point in West Java-Indonesia

    Directory of Open Access Journals (Sweden)

    Dianita Cindy

    2016-01-01

    Full Text Available Indonesia is one of the highest greenhouse emitters in the world. As a response of this problem, Indonesia declared the national action plan to focus on national greenhouse gas (GHG reduction by 26 % by 2020. To achieve this target, Government puts energy sector as one of the top priorities since it is the second strongest contributor to national GHG emissions. The main purpose of this paper is to apply the method of fugitive emissions calculation to the existing natural gas pipeline in Indonesia. Fugitive emissions are the major component of GHG emissions from natural gas systems and methane (CH4, the primary component of natural gas pipeline, is a potent GHG. Tiered approaches from Interstate Natural Gas Association of America (INGAA are implemented in this paper as the estimation guidelines. A case study of a natural gas pipeline system in Indonesia is analyzed to compare the GHG emissions level resulted from Tier 1 and Tier 2 methods. In these methods, the input data are pipeline length, the number of compressor stations, and the number of meter and pressure regulation stations. In this case, the GHG emissions level of Tier 2 is significantly different from Tier 1. The variation of pipeline length shows that for the length under 479.2 miles, Tier 1 gives lower amount of CO2 equivalent than Tier 2. The differences of these estimation methods and results can be furtherly developed to provide relevant information and recommendation for the Companies and Government to record the emissions level from natural gas transmission pipeline according to their needs and purposes.

  1. Determination of low-level pesticide residues in soft drinks and sports drinks by liquid chromatography with tandem mass spectrometry: collaborative study.

    Science.gov (United States)

    Miller, Kathleen D; Milne, Paul

    2008-01-01

    A collaborative study was conducted on a method for the measurement of 11 low-level pesticide residues in soft drinks and sports drinks by liquid chromatography with tandem mass spectrometry. The pesticide residues determined in this study were alachlor, atrazine, butachlor, isoproturon, malaoxon, monocrotophos, methyl paraoxon, phorate, phorate sulfone, phorate sulfoxide, and 2,4-dichlorophenoxyacetic acid (2,4-D). Blind fortification solutions containing 3 different levels of pesticide residues were provided to 9 collaborating laboratories to create test samples at concentrations of 0, 0.1, and 0.5 microg/L with a 10-fold concentration for phorate in a total of 6 matrixes (2 colas, 1 diet cola, 1 clear lemon-lime soft drink, 1 orange soft drink, and 1 sports drink). Good qualitative performance of the method was demonstrated for all pesticide residues. Reproducibility relative standard deviation (RSDR) ranged from 7 to 151% for alachlor, atrazine, butachlor, isoproturon, malaoxon, monocrotophos, methyl paraoxon, phorate, phorate sulfone, phorate sulfoxide, and 2,4-D at the 0.1 microg/L level (1.0 microg/L for phorate). At 0.5 microg/L (5.0 microg/L for phorate), RSDR ranged from 9 to 57% for alachlor, atrazine, butachlor isoproturon, malaoxon, monocrotophos, methyl paraoxon, phorate, phorate sulfone, phorate sulfoxide, and 2,4-D in all matrixes. Repeatability relative standard deviation (RSDr), applicable to the diet cola and sports drink, ranged from 0 to 124% for the 11 pesticide residues at the 0.1 microg/L level (1.0 microg/L for phorate). At 0.5 microg/L (5.0 microg/L for phorate), RSDr ranged from 4 to 26%. Recoveries for the 11 pesticide residues in all matrixes ranged from 84 to 300% at the 0.1 microg/L level (1.0 microg/L for phorate) and from 66 to 127% at the 0.5 microg/L (5.0 microg/L for phorate) level. Coefficients of determination (r2) of the matrix-matched calibration curves were > or = 0.95. It is recommended that the method be accepted by AOAC

  2. PAHs levels in gas and particle-bound phase in schools at different locations in Serbia

    Directory of Open Access Journals (Sweden)

    Živković Marija

    2015-01-01

    Full Text Available This study investigated seasonal variation of PAHs and their partition between gas and particulate-bounded phases in indoor and outdoor air in 4 schools in Serbia located at different locations. The sampling campaigns were conducted during one workweek at each school successively. Campaigns were conducted in schools during heating and non-heating seasons in December 2011 and June 2012. Seasonal variations of gas and particle-bounded PAHs concentrations were observed with higher levels during heating season. The highest total PAH values were associated with the gas phase in both sampling periods. The total PAHs concentration at indoor and at the outdoor sites, during heating season, ranged from 88.45 to 447.72 ng/m3 and 201.69 to 1017.15 ng/m3, respectively. During non-heating season, the total PAHs concentration ranged from 36.91 to 271.57 ng/m3 in indoor environment and 27.00 to 132.32 ng/m3 in outdoor environment. Most of the I/O ratios were less than 1, which indicated that the indoor PAHs were mostly from outdoor sources. The use of diagnostic ratio showed that traffic emission and coal combustion are the major sources of PAHs. Only the diagnostic ratios for the school, located near the industrial area, showed significant deviation compared to other schools. [Projekat Ministarstva nauke Republike Srbije, br. TR33036: Development of new meteorological mast for turbulence parameters characterization and br. III42008: Evaluation of Energy Performances and Indoor Environment Quality of Educational Buildings in Serbia with Impact to Health

  3. Growth response of Spirulina platensis PCC9108 to elevated CO2 levels and flue gas

    Directory of Open Access Journals (Sweden)

    Seyedmahdi Hoseini

    2014-01-01

    Full Text Available Introduction: Because their ability to capture CO2, photosynthetical microorganisms have some advantages to CO2 mitigation from high CO2 streams such as flue gases and they can use CO2 as carbon source. Recently, experts have made efforts to exploit microorganisms intended for recovering CO2 from power plants. Materials and methods: To achieve this purpose, we studied the growth response of the cyanobacterium Spirulina platensis PCC9108 under different concentrations of carbon dioxide (ranging from 0.036% to 10% and flue gas in a bench-scale system. Preparation of different concentrations of CO2 and injection into Erlenmeyer flasks was performed by a system including air compressor, CO2 capsule, pressure gauge and flow meter. Results: The main goal of studying this paper is a survey of organism's potential to grow by generated CO2 from flue gas of power plant. It already had the potential and highest biomass production recorded at 8% CO2 (v/v. Also we proved that S.platensis PCC9108 can be grown under flue gas, although biomass production decreased fairly. Total lipid content of algae interestingly enhanced with elevated CO2 levels from ambient air to 4% and 6% which ranged from 14.5 to 15.8 and 16 dry weight (wt. % respectively. In contrast, total protein content illustrated no difference between all treatment and its value was about 46 wt.%. Discussion and conclusion: The results of present study suggested that understudied S.platensis PCC9108 is appropriate for mitigating CO2 because of its carbon fixation ability. Also due to its high protein content, this cyanobacterium is a good candidate to produce SCP (single cell protein.

  4. Nonlinear Adaptive Power-Level Control for Modular High Temperature Gas-Cooled Reactors

    Science.gov (United States)

    Dong, Zhe

    2013-04-01

    After the Fukushima nuclear accident, much more attention has to be drawn on the safety issues. The improvement of safety has already become the focus of the developing trend of the nuclear energy systems. Due to the inherent safety feature and the potential economic competitiveness, the modular high temperature gas-cooled reactor (MHTGR) has been seen as the central part of the next generation of nuclear plant (NGNP). Power-level control is one of the key techniques that guarantee the safe, stable and efficient operation for nuclear reactors. Since the MHTGR dynamics has the features of strong nonlinearity and uncertainty, in order to improve the operation performance, it is meaningful to develop the nonlinear adaptive power-level control law for the MHTGR. Based on using the natural dynamic features beneficial to system stabilization, a novel nonlinear adaptive power-level control is given for the MHTGR in this paper. It is theoretically proved that this newly-built controller does not only provide globally asymptotic closed-loop stability but is also adaptive to the system uncertainty. This control law is then applied to the power-level regulation of the pebble-bed MHTGR of the HTR-PM power plant. Numerical simulation results show the feasibility of this control law and the relationship between the performance and controller parameters.

  5. Poly-use multi-level sampling system for soil-gas transport analysis in the vadose zone.

    Science.gov (United States)

    Nauer, Philipp A; Chiri, Eleonora; Schroth, Martin H

    2013-10-01

    Soil-gas turnover is important in the global cycling of greenhouse gases. The analysis of soil-gas profiles provides quantitative information on below-ground turnover and fluxes. We developed a poly-use multi-level sampling system (PMLS) for soil-gas sampling, water-content and temperature measurement with high depth resolution and minimal soil disturbance. It is based on perforated access tubes (ATs) permanently installed in the soil. A multi-level sampler allows extraction of soil-gas samples from 20 locations within 1 m depth, while a capacitance probe is used to measure volumetric water contents. During idle times, the ATs are sealed and can be equipped with temperature sensors. Proof-of-concept experiments in a field lysimeter showed good agreement of soil-gas samples and water-content measurements compared with conventional techniques, while a successfully performed gas-tracer test demonstrated the feasibility of the PMLS to determine soil-gas diffusion coefficients in situ. A field application of the PMLS to quantify oxidation of atmospheric CH4 in a field lysimeter and in the forefield of a receding glacier yielded activity coefficients and soil-atmosphere fluxes well in agreement with previous studies. With numerous options for customization, the presented tool extends the methodological choices to investigate soil-gas transport in the vadose zone.

  6. An approximate-reasoning-based method for screening high-level waste tanks for flammable gas

    International Nuclear Information System (INIS)

    Eisenhawer, S.W.; Bott, T.F.; Smith, R.E.

    1998-01-01

    The in situ retention of flammable gas produced by radiolysis and thermal decomposition in high-level waste can pose a safety problem if the gases are released episodically into the dome space of a storage tank. Screening efforts at Hanford have been directed at identifying tanks in which this situation could exist. Problems encountered in screening motivated an effort to develop an improved screening methodology. Approximate reasoning (AR) is a formalism designed to emulate the kinds of complex judgments made by subject matter experts. It uses inductive logic structures to build a sequence of forward-chaining inferences about a subject. AR models incorporate natural language expressions known as linguistic variables to represent evidence. The use of fuzzy sets to represent these variables mathematically makes it practical to evaluate quantitative and qualitative information consistently. The authors performed a pilot study to investigate the utility of AR for flammable gas screening. They found that the effort to implement such a model was acceptable and that computational requirements were reasonable. The preliminary results showed that important judgments about the validity of observational data and the predictive power of models could be made. These results give new insights into the problems observed in previous screening efforts

  7. Dynamics of gas-surface interactions atomic-level understanding of scattering processes at surfaces

    CERN Document Server

    Díez Muniño, Ricardo

    2013-01-01

    This book gives a representative survey of the state of the art of research on gas-surface interactions. It provides an overview of the current understanding of gas surface dynamics and, in particular, of the reactive and non-reactive processes of atoms and small molecules at surfaces. Leading scientists in the field, both from the theoretical and the experimental sides, write in this book about their most recent advances. Surface science grew as an interdisciplinary research area over the last decades, mostly because of new experimental technologies (ultra-high vacuum, for instance), as well as because of a novel paradigm, the ‘surface science’ approach. The book describes the second transformation which is now taking place pushed by the availability of powerful quantum-mechanical theoretical methods implemented numerically. In the book, experiment and theory progress hand in hand with an unprecedented degree of accuracy and control. The book presents how modern surface science targets the atomic-level u...

  8. Studies Related to Chemical Mechanisms of Gas Formation in Hanford High-Level Nuclear Wastes

    International Nuclear Information System (INIS)

    Barefield, E. Kent; Liotta, Charles L.; Neumann, Henry M.

    2002-01-01

    The objective of this work is to develop a more detailed mechanistic understanding of the thermal reactions that lead to gas production in certain high-level waste storage tanks at the Hanford, Washington site. Prediction of the combustion hazard for these wastes and engineering parameters for waste processing depend upon both a knowledge of the composition of stored wastes and the changes that they undergo as a result of thermal and radiolytic decomposition. Since 1980 when Delagard first demonstrated that gas production (H2and N2O initially, later N2 and NH3)in the affected tanks was related to oxidative degradation of metal complexants present in the waste, periodic attempts have been made to develop detailed mechanisms by which the gases were formed. These studies have resulted in the postulation of a series of reactions that account for many of the observed products, but which involve several reactions for which there is limited, or no, precedent. For example, Al(OH)4 has been postulated to function as a Lewis acid to catalyze the reaction of nitrite ion with the metal complexants, NO is proposed as an intermediate, and the ratios of gaseous products may be a result of the partitioning of NO between two or more reactions. These reactions and intermediates have been the focus of this project since its inception in 1996

  9. An approximate-reasoning-based method for screening high-level waste tanks for flammable gas

    Energy Technology Data Exchange (ETDEWEB)

    Eisenhawer, S.W.; Bott, T.F.; Smith, R.E.

    1998-07-01

    The in situ retention of flammable gas produced by radiolysis and thermal decomposition in high-level waste can pose a safety problem if the gases are released episodically into the dome space of a storage tank. Screening efforts at Hanford have been directed at identifying tanks in which this situation could exist. Problems encountered in screening motivated an effort to develop an improved screening methodology. Approximate reasoning (AR) is a formalism designed to emulate the kinds of complex judgments made by subject matter experts. It uses inductive logic structures to build a sequence of forward-chaining inferences about a subject. AR models incorporate natural language expressions known as linguistic variables to represent evidence. The use of fuzzy sets to represent these variables mathematically makes it practical to evaluate quantitative and qualitative information consistently. The authors performed a pilot study to investigate the utility of AR for flammable gas screening. They found that the effort to implement such a model was acceptable and that computational requirements were reasonable. The preliminary results showed that important judgments about the validity of observational data and the predictive power of models could be made. These results give new insights into the problems observed in previous screening efforts.

  10. J-shape ventilation system for controlling high gas emission at fully mechanized sub-level caving face

    Energy Technology Data Exchange (ETDEWEB)

    Wang, K.; Yu, Q.; Miao, X. (and others) [CUMT, Xuzhou (China). School of Mineral and Safety Engineering

    2004-07-01

    Considering the practical condition of No. 5201 fully mechanized sub-level caving face in Wangzhuang Coal Mine of Lu'an Mining Group, and based on the successfully retaining of small section entry along gob side, a method of J-shape ventilation system and its regulating technology were put forward for controlling high gas emission at fully mechanized sub-level caving face. Essentially, the J-shape ventilation system has one intake and two returns for controlling high gas emission according to different gas sources using ventilation measure. Through practical application it is proved that local gas accumulation at coal face and its upper corner can be eliminated by adopting J-shape ventilation system, thus high-production and high-efficiency of fully mechanized sub-level caving face can be also realized. 6 refs., 6 figs., 1 tab.

  11. An assessment of the possible fate of gas generated in a repository for low- and intermediate-level waste

    International Nuclear Information System (INIS)

    Leupin, O.X.; Cloet, V.; Marschall, P.; Schwyn, B.; Smith, P.; Zeyer, J.; Bernier-Latmani, R.; Papafotiou, A.; Stroes-Gascoyne, S.

    2016-12-01

    The present study provides an assessment of reactions that result in a gas pressure reduction - also called gas sinks - in a generic deep geological repository for low- and intermediate-level waste in Opalinus Clay. Both chemical reactions and microbial activity may contribute to or reduce gas pressure build-up. A complete synopsis is given, comprising the current state of chemical, microbial and geoscientific understanding of gas generation and consumption in a L/ILW repository. The degradation of organic materials (by both microbial and chemical reactions) and the anoxic corrosion of metals will generate various gaseous products such as hydrogen, carbon dioxide, methane, hydrogen sulphide and ammonia. Some of these gas species are expected to further react with materials present at the point of origin. More particularly, carbon dioxide and hydrogen sulphide are expected to react entirely with e.g. cement, water or iron. Thus, they do not contribute to a gas pressure build-up in the repository. The remaining gas species - mainly hydrogen, methane and small amounts of ammonia - are assumed not to react at the point of origin and can thus contribute to gas pressure build-up. Gas pressure build-up in the L/ILW emplacement caverns will result in gas migrating through the gas permeable seals and through the excavation-damaged zone to reach the operational and construction tunnels where microorganisms may utilise the gas and thus reduce gas pressure build-up. In order to allow bacteria to thrive over longer periods, the backfill material of the operational tunnel needs to have sufficient porosity and a pore water composition for favourable living conditions. Experimental findings at the Mont Terri underground rock laboratory show that bacteria found in borehole water are efficient at oxidising hydrogen as long as sulphate is present in the borehole water. Examples from nature and engineered underground structures provide supporting evidence that these assumptions are

  12. Surface gas pollutants in Lhasa, a highland city of Tibet: current levels and pollution implications

    Science.gov (United States)

    Ran, L.; Lin, W. L.; Deji, Y. Z.; La, B.; Tsering, P. M.; Xu, X. B.; Wang, W.

    2014-05-01

    Through several years of development, the city of Lhasa has become one of the most populated and urbanized areas on the highest plateau in the world. In the process of urbanization, current and potential air quality issues have been gradually concerned. To investigate the current status of air pollution in Lhasa, various gas pollutants including NOx, CO, SO2 and O3 were continuously measured from June 2012 to May 2013 at an urban site (29.40° N, 91.08° E, 3650 m a.s.l.). The seasonal variations of primary gas pollutants exhibited a peak from November to January with a large variability. High concentrations of primary trace gases almost exclusively occurred under low wind speed and showed no distinct dependence on wind direction, implying local urban emissions to be predominant. A comparison of NO2, CO and SO2 concentrations in summer between 1998 and 2012 indicated a significant increase in emissions of these gas pollutants and a change in their intercorrelations, as a result of a substantial growth in the demand of energy consumption using fossil fuels instead of previously widely used biofuels. The pronounced diurnal double peaks of primary trace gases in all seasons suggested automobile exhaust to be a major emission source in Lhasa. The secondary gas pollutant O3 displayed an average diurnal cycle of a shallow flat peak for about 4-5 h in the afternoon and a minimum in the early morning. Nighttime O3 was sometimes completely consumed by the high level of NOx. Seasonally, the variations of O3 concentrations displayed a low valley in winter and a peak in spring. In autumn and winter, transport largely contributed to the observed O3 concentrations, given its dependence on wind speed and wind direction, while in spring and summer photochemistry played an important role. A more efficient buildup of O3 concentrations in the morning and a higher peak in the afternoon was found in summer 2012 than in 1998. An enhancement in O3 concentrations would be expected in the

  13. Surface gas pollutants in Lhasa, a highland city of Tibet - current levels and pollution implications

    Science.gov (United States)

    Ran, L.; Lin, W. L.; Deji, Y. Z.; La, B.; Tsering, P. M.; Xu, X. B.; Wang, W.

    2014-10-01

    Through several years of development, the city of Lhasa has become one of the most populated and urbanized areas on the highest plateau in the world. In the process of urbanization, current and potential air quality issues have been gradually concerned. To investigate the current status of air pollution in Lhasa, various gas pollutants including NOx, CO, SO2, and O3, were continuously measured from June 2012 to May 2013 at an urban site (29.40° N, 91.08° E, 3650 m a.s.l.). The seasonal variations of primary gas pollutants exhibited a peak from November to January with a large variability. High mixing ratios of primary trace gases almost exclusively occurred under low wind speed and showed no distinct dependence on wind direction, implying local urban emissions to be predominant. A comparison of NO2, CO, and SO2 mixing ratios in summer between 1998 and 2012 indicated a significant increase in emissions of these gas pollutants and a change in their intercorrelations, as a result of a substantial growth in the demand of energy consumption using fossil fuels instead of previously widely used biomass. The pronounced diurnal double peaks of primary trace gases in all seasons suggested automobile exhaust to be a major emission source in Lhasa. The secondary gas pollutant O3 displayed an average diurnal cycle of a shallow flat peak for about 4-5 h in the afternoon and a minimum in the early morning. Nighttime O3 was sometimes completely consumed by the high level of NOx. Seasonally, the variations of O3 mixing ratios displayed a low valley in winter and a peak in spring. In autumn and winter, transport largely contributed to the observed O3 mixing ratios, given its dependence on wind speed and wind direction, while in spring and summer photochemistry played an important role. A more efficient buildup of O3 mixing ratios in the morning and a higher peak in the afternoon was found in summer 2012 than in 1998. An enhancement in O3 mixing ratios would be expected in the

  14. Common bean growth, N uptake and seed production in sandy loam soil as affected by application of plant residues, nitrogen and irrigation level

    International Nuclear Information System (INIS)

    Abdallah, A.A.G.

    2002-01-01

    Field experiment was conducted at the experimental farm, Inshas, atomic energy authority, egypt. Common bean seeds e.v. Nebrasks were cultivated in sandy loan soil using drip irrigation system prepared for this purpose. Two water regimes, i.e., 100% (793.0 m 3 /fed.) and 65% (513.0 m 3 /fed.) of maximum available water were used in main plots. Where in sub plots two fertilizers types were applied i.e., soybean plant residues which contains N 15 labelled as an organic matter without any addition of any fertilizer and nitrogen as chemical fertilizer without using organic matter. The obtained results indicated that, application of plant residues was superior for total seed yield comparing to nitrogen fertilization treatments. This N source with irrigation level of 793.33 m 3 /fed. had a slight increase in total seed yield comparing with (513.0 m 3 /fed.). Irrigation level of 513.0 m 3 /fed. (65% MAW) as well as application of soybean plant residues showed the highest value of water use efficiency. The highest value of N seed percentage was obtained irrigation level with (513.0 m 3 /fed.). Soybean plant residues improved and increased seeds N content, and total seeds protein content. Both N chemical and irrigation level (65% Maw) recorded highest values with N 15 % atom excess. This result has been obtained at two growth stages and seed yield. The same trend of N 15 % atom excess reflected N utilized with both growth stages and seed yield

  15. Reasoned opinion on the dietary risk assessment for proposed temporary maximum residue levels (MRLs) of didecyldimethylammonium chloride (DDAC) and benzalkonium chloride (BAC)

    OpenAIRE

    European Food Safety Authority

    2014-01-01

    EFSA was requested by the European Commission to perform a dietary exposure assessment for the proposed temporary maximum residue levels (MRLs) for didecyldimethylammonium chloride (DDAC) and benzalkonium chloride (BAC) (0.1 mg/kg, respectively, for all food commodities covered by the EU MRL legislation). Based on the information, EFSA did not identify potential consumer health risks for these proposed MRLs. Thus, the proposed MRLs are considered to be sufficiently protective. However, due to...

  16. SequenceCEROSENE: a computational method and web server to visualize spatial residue neighborhoods at the sequence level.

    Science.gov (United States)

    Heinke, Florian; Bittrich, Sebastian; Kaiser, Florian; Labudde, Dirk

    2016-01-01

    To understand the molecular function of biopolymers, studying their structural characteristics is of central importance. Graphics programs are often utilized to conceive these properties, but with the increasing number of available structures in databases or structure models produced by automated modeling frameworks this process requires assistance from tools that allow automated structure visualization. In this paper a web server and its underlying method for generating graphical sequence representations of molecular structures is presented. The method, called SequenceCEROSENE (color encoding of residues obtained by spatial neighborhood embedding), retrieves the sequence of each amino acid or nucleotide chain in a given structure and produces a color coding for each residue based on three-dimensional structure information. From this, color-highlighted sequences are obtained, where residue coloring represent three-dimensional residue locations in the structure. This color encoding thus provides a one-dimensional representation, from which spatial interactions, proximity and relations between residues or entire chains can be deduced quickly and solely from color similarity. Furthermore, additional heteroatoms and chemical compounds bound to the structure, like ligands or coenzymes, are processed and reported as well. To provide free access to SequenceCEROSENE, a web server has been implemented that allows generating color codings for structures deposited in the Protein Data Bank or structure models uploaded by the user. Besides retrieving visualizations in popular graphic formats, underlying raw data can be downloaded as well. In addition, the server provides user interactivity with generated visualizations and the three-dimensional structure in question. Color encoded sequences generated by SequenceCEROSENE can aid to quickly perceive the general characteristics of a structure of interest (or entire sets of complexes), thus supporting the researcher in the initial

  17. Neutron residual stress measurements in linepipe

    Science.gov (United States)

    Law, Michael; Gnaëpel-Herold, Thomas; Luzin, Vladimir; Bowie, Graham

    2006-11-01

    Residual stresses in gas pipelines are generated by manufacturing and construction processes and may affect the subsequent pipe integrity. In the present work, the residual stresses in eight samples of linepipe were measured by neutron diffraction. Residual stresses changed with some coating processes. This has special implications in understanding and mitigating stress corrosion cracking, a major safety and economic problem in some gas pipelines.

  18. Neutron residual stress measurements in linepipe

    International Nuclear Information System (INIS)

    Law, Michael; Gnaepel-Herold, Thomas; Luzin, Vladimir; Bowie, Graham

    2006-01-01

    Residual stresses in gas pipelines are generated by manufacturing and construction processes and may affect the subsequent pipe integrity. In the present work, the residual stresses in eight samples of linepipe were measured by neutron diffraction. Residual stresses changed with some coating processes. This has special implications in understanding and mitigating stress corrosion cracking, a major safety and economic problem in some gas pipelines

  19. Dechlorane Plus flame retardant in kingfishers (Alcedo atthis) from an electronic waste recycling site and a reference site, South China: Influence of residue levels on the isomeric composition

    International Nuclear Information System (INIS)

    Mo, Ling; Wu, Jiang-Ping; Luo, Xiao-Jun; Sun, Yu-Xin; Zheng, Xiao-Bo; Zhang, Qiang; Zou, Fa-Shen; Mai, Bi-Xian

    2013-01-01

    Dechlorane Plus (DP) isomers were examined in common kingfishers (Alcedo atthis) and their prey fishes collected from an electronic waste (e-waste) recycling site and a reference site in South China, to investigate the possible influence of DP residue levels on the isomeric compositions. ∑DP (sum of syn-DP and anti-DP) concentrations in kingfishers from the e-waste recycling site ranged from 29 to 150 (median of 58) ng/g lipid weight (lw), which were one order of magnitude greater than those from the reference site (median = 3.9 ng/g lw). The isomer fractions of anti-DP (f anti ) in kingfishers from the e-waste recycling site (mean of 0.65) were significantly smaller than those from the reference site (0.76). Additionally, the f anti values were negatively correlated to logarithm of ∑DP concentrations in the kingfishers (r 2 = 0.41, p 11 -DP in the kingfishers is likely originated from the diet. ► The f anti values were negatively correlated to DP residue levels in the kingfishers. -- DP residue levels influence the isomeric compositions in the investigated kingfishers

  20. Measurement of trace impurities in ultra pure hydrogen and deuterium at the parts-per-billion level using gas chromatography

    Science.gov (United States)

    Ganzha, V.; Ivshin, K.; Kammel, P.; Kravchenko, P.; Kravtsov, P.; Petitjean, C.; Trofimov, V.; Vasilyev, A.; Vorobyov, A.; Vznuzdaev, M.; Wauters, F.

    2018-02-01

    A series of muon experiments at the Paul Scherrer Institute in Switzerland deploy ultra-pure hydrogen active targets. A new gas impurity analysis technique was developed, based on conventional gas chromatography, with the capability to measure part-per-billion (ppb) traces of nitrogen and oxygen in hydrogen and deuterium. Key ingredients are a cryogenic admixture accumulation, a directly connected sampling system and a dedicated calibration setup. The dependence of the measured concentration on the sample volume was investigated, confirming that all impurities from the sample gas are collected in the accumulation column and measured with the gas chromatograph. The system was calibrated utilizing dynamic dilution of admixtures into the gas flow down to sub-ppb level concentrations. The total amount of impurities accumulated in the purification system during a three month long experimental run was measured and agreed well with the calculated amount based on the measured concentrations in the flow.

  1. Development and comparison of two multi-residue methods for the analysis of select pesticides in honey bees, pollen, and wax by gas chromatography-quadrupole mass spectrometry.

    Science.gov (United States)

    Li, Yuanbo; Kelley, Rebecca A; Anderson, Troy D; Lydy, Michael J

    2015-08-01

    One of the hypotheses that may help explain the loss of honey bee colonies worldwide is the increasing potential for exposure of honey bees to complex mixtures of pesticides. To better understand this phenomenon, two multi-residue methods based on different extraction and cleanup procedures have been developed, and compared for the determination of 11 relevant pesticides in honey bees, pollen, and wax by gas chromatography-quadrupole mass spectrometry. Sample preparatory methods included solvent extraction followed by gel permeation chromatography (GPC) cleanup and cleanup using a dispersive solid-phase extraction with zirconium-based sorbents (Z-Sep). Matrix effects, method detection limits, recoveries, and reproducibility were evaluated and compared. Method detection limits (MDL) of the pesticides for the GPC method in honey bees, pollen, and wax ranged from 0.65 to 5.92 ng/g dw, 0.56 to 6.61 ng/g dw, and 0.40 to 8.30 ng/g dw, respectively, while MDLs for the Z-Sep method were from 0.33 to 4.47 ng/g dw, 0.42 to 5.37 ng/g dw, and 0.51 to 5.34 ng/g dw, respectively. The mean recoveries in all matrices and at three spiking concentrations ranged from 64.4% to 149.5% and 71.9% to 126.2% for the GPC and Z-Sep methods, with relative standard deviation between 1.5-25.3% and 1.3-15.9%, respectively. The results showed that the Z-Sep method was more suitable for the determination of the target pesticides, especially chlorothalonil, in bee hive samples. The Z-Sep method was then validated using a series of field-collected bee hive samples taken from honey bee colonies in Virginia. Copyright © 2015 Elsevier B.V. All rights reserved.

  2. Influence of soil organic C content on the greenhouse gas emission potential after application of biogas residues or cattle slurry - Results from a pot experiment

    Science.gov (United States)

    Heintze, Gawan

    2017-04-01

    Influence of soil organic C content on the greenhouse gas emission potential after application of biogas residues or cattle slurry - Results from a pot experiment Gawan Heintze1,2, Tim Eickenscheidt1, Urs Schmidthalter2 and Matthias Drösler1 1University of Applied Sciences Weihenstephan-Triesdorf, Chair of Vegetation Ecology, Weihenstephaner Berg 4, 85354 Freising, Germany 2Technische Universität München, Chair of Plant Nutrition, Emil-Ramann-Str. 2, 85354 Freising, Germany The European Union Renewable Energy Directive, which sets a binding target of a final energy consumption of 20% from renewable sources by 2020, has markedly promoted the increase of biogas plants, particularly in Germany. As a consequence, a large amount of biogas residue remains as a by-product of the fermentative process. These residues are now widely used instead of mineral fertilizers or animal slurries to maintain soil fertility and productivity. However, to date, the effect of the application of biogas residue on greenhouse gas (GHG) emission, compared to that of other organic fertilizers, is contradictory in literature, not having been completely understood. It is often stated that GHG fluxes are closely related to the quality of the raw material, particularly the type of soil to which the digestates are applied. This study addresses the questions (a) to what extent are the applications of biogas digestate and cattle slurry different in terms of their GHG emission (CO2, CH4 and N2O) potential, and (b) how do different soil organic carbon contents (SOCs) influence the rate of GHG exchange. We hypothesize that, i) cattle slurry application enhances the CO2 and N2O fluxes compared to the biogas digestate due to the overall higher C and N input, and ii) that with increasing SOC and N content, higher emissions of CO2 and N2O can be expected. The study was conducted as a pot experiment. Biogas digestate and cattle slurry were applied to and incorporated into three different soil types with

  3. The High Level Mathematical Models in Calculating Aircraft Gas Turbine Engine Parameters

    Directory of Open Access Journals (Sweden)

    Yu. A. Ezrokhi

    2017-01-01

    Full Text Available The article describes high-level mathematical models developed to solve special problems arising at later stages of design with regard to calculation of the aircraft gas turbine engine (GTE under real operating conditions. The use of blade row mathematics models, as well as mathematical models of a higher level, including 2D and 3D description of the working process in the engine units and components, makes it possible to determine parameters and characteristics of the aircraft engine under conditions significantly different from the calculated ones.The paper considers application of mathematical modelling methods (MMM for solving a wide range of practical problems, such as forcing the engine by injection of water into the flowing part, estimate of the thermal instability effect on the GTE characteristics, simulation of engine start-up and windmill starting condition, etc. It shows that the MMM use, when optimizing the laws of the compressor stator control, as well as supplying cooling air to the hot turbine components in the motor system, can significantly improve the integral traction and economic characteristics of the engine in terms of its gas-dynamic stability, reliability and resource.It ought to bear in mind that blade row mathematical models of the engine are designed to solve purely "motor" problems and do not replace the existing models of various complexity levels used in calculation and design of compressors and turbines, because in “quality” a description of the working processes in these units is inevitably inferior to such specialized models.It is shown that the choice of the mathematical modelling level of an aircraft engine for solving a particular problem arising in its designing and computational study is to a large extent a compromise problem. Despite the significantly higher "resolution" and information ability the motor mathematical models containing 2D and 3D approaches to the calculation of flow in blade machine

  4. Monitoring of Pesticide Residues in Commonly Used Fruits and Vegetables in Kuwait

    OpenAIRE

    Jallow, Mustapha F. A.; Awadh, Dawood G.; Albaho, Mohammed S.; Devi, Vimala Y.; Ahmad, Nisar

    2017-01-01

    The presence of pesticide residues in primary and derived agricultural products raises serious health concerns for consumers. The aim of this study was to assess the level of pesticide residues in commonly consumed fruits and vegetables in Kuwait. A total of 150 samples of different fresh vegetables and fruits were analyzed for the presence of 34 pesticides using the quick easy cheap effective rugged and safe (QuEChERS) multi-residue extraction, followed by gas chromatography-mass spectrometr...

  5. SigniSite: Identification of residue-level genotype-phenotype correlations in protein multiple sequence alignments

    DEFF Research Database (Denmark)

    Jessen, Leon Ivar; Hoof, Ilka; Lund, Ole

    2013-01-01

    Site does not require any pre-definition of subgroups or binary classification. Input is a set of protein sequences where each sequence has an associated real number, quantifying a given phenotype. SigniSite will then identify which amino acid residues are significantly associated with the data set......) using a set of human immunodeficiency virus protease-inhibitor genotype–phenotype data and corresponding resistance mutation scores from the Stanford University HIV Drug Resistance Database, and a data set of protein families with experimentally annotated SDPs. For both data sets, SigniSite was found...

  6. Comparing facility-level methane emission rate estimates at natural gas gathering and boosting stations

    Directory of Open Access Journals (Sweden)

    Timothy L. Vaughn

    2017-11-01

    Full Text Available Coordinated dual-tracer, aircraft-based, and direct component-level measurements were made at midstream natural gas gathering and boosting stations in the Fayetteville shale (Arkansas, USA. On-site component-level measurements were combined with engineering estimates to generate comprehensive facility-level methane emission rate estimates (“study on-site estimates (SOE” comparable to tracer and aircraft measurements. Combustion slip (unburned fuel entrained in compressor engine exhaust, which was calculated based on 111 recent measurements of representative compressor engines, accounts for an estimated 75% of cumulative SOEs at gathering stations included in comparisons. Measured methane emissions from regenerator vents on glycol dehydrator units were substantially larger than predicted by modelling software; the contribution of dehydrator regenerator vents to the cumulative SOE would increase from 1% to 10% if based on direct measurements. Concurrent measurements at 14 normally-operating facilities show relative agreement between tracer and SOE, but indicate that tracer measurements estimate lower emissions (regression of tracer to SOE = 0.91 (95% CI = 0.83–0.99, R2 = 0.89. Tracer and SOE 95% confidence intervals overlap at 11/14 facilities. Contemporaneous measurements at six facilities suggest that aircraft measurements estimate higher emissions than SOE. Aircraft and study on-site estimate 95% confidence intervals overlap at 3/6 facilities. The average facility level emission rate (FLER estimated by tracer measurements in this study is 17–73% higher than a prior national study by Marchese et al.

  7. Determination of leveled costs of electric generation for gas plants, coal and nuclear; Determinacion de costos nivelados de generacion electrica para plantas de gas, carbon y nucleares

    Energy Technology Data Exchange (ETDEWEB)

    Alonso V, G.; Palacios H, J.C.; Ramirez S, J.R.; Gomez, A. [ININ, 52045 Ocoyoacac, Estado de Mexico (Mexico)]. e-mail: galonso@nuclear.inin.mx

    2005-07-01

    The present work analyzes the leveled costs of electric generation for different types of nuclear reactors known as Generation III, these costs are compared with the leveled costs of electric generation of plants with the help of natural gas and coal. In the study several discount rates were used to determine their impact in the initial investment. The obtained results are comparable with similar studies and they show that it has more than enough the base of the leveled cost the nuclear option it is quite competitive in Mexico. Also in this study it is also thinks about the economic viability of a new nuclear power station in Mexico. (Author)

  8. Residues of pharmaceutical products in recycled organic manure produced from sewage sludge and solid waste from livestock and relationship to their fermentation level.

    Science.gov (United States)

    Motoyama, Miki; Nakagawa, Shuhei; Tanoue, Rumi; Sato, Yuri; Nomiyama, Kei; Shinohara, Ryota

    2011-07-01

    In recent years, sludge generated in sewage treatment plants (STPs) and solid waste from livestock being utilized is useful for circulation of nourishment in farmlands as recycled organic manure (ROM). In this study, we determined the residue levels and patterns of 12 pharmaceutical products generated by human activity in the ROMs produced from human waste sludge (HWS), sewage sludge (SS), cattle manure (CM), poultry manure (PM), swine manure (SM) and horse manure (HM). The kind and number of pharmaceutical products detected in ROMs were different. Fluoroquinolones (FQs) were detected at high levels in HWS and SS samples. In addition, the detection frequency and concentration levels of sulfonamides (SAs) in PM and SM were high. Moreover, high concentrations of chlortetracycline (CTC) were found in only SM. These differences reflect specific adherence adsorption of the pharmaceutical products to different livestock and humans. Moreover, it was found that the concentrations of pharmaceutical products and fermentation levels of ROMs had significant positive correlation (r=0.41, p=0.024). When the fermentation test of ROM was conducted in a rotary fermentor in a lab scale test, the residue levels of pharmaceutical products decreased effectively except carbamazepine (CBZ). The rates of decrease were in the case of tetracyclines (TCs): 85-92%, FQs: 81-100%, erythromycine: 67%, SAs: 79-95%, trimethoprim: 86% and CBZ: 37% by 30 d. Pharmaceutical products that can be decomposed by fermentation process at the lowest impact of residual antibiotic activities may therefore be considered as environmentally friendly medicines. Copyright © 2011 Elsevier Ltd. All rights reserved.

  9. Leveling the playing field of transportation fuels: Accounting for indirect emissions of natural gas

    International Nuclear Information System (INIS)

    Sexton, Steven; Eyer, Jonathan

    2016-01-01

    Natural gas transportation fuels are credited in prior studies with greenhouse gas emissions savings relative to petroleum-based fuels and relative to the total emissions of biofuels. These analyses, however, overlook a source of potentially large indirect emissions from natural gas transportation fuels, namely the emissions from incremental coal-fired generation caused by price-induced substitutions away from natural-gas-fired electricity generation. Because coal-fired generation emits substantially more greenhouse gases and criteria air pollutants than natural-gas-fired generation, this indirect coal-use change effect diminishes potential emissions savings from natural gas transportation fuels. Estimates from a parameterized multi-market model suggest the indirect coal-use change effect rivals in magnitude the indirect land-use change effect of biofuels and renders natural gas fuels as carbon intensive as petroleum fuels. - Highlights: •Natural gas used in transport causes indirect emissions in the electricity sector. •These emissions result from increased coal use in electricity generation. •They rival in magnitude indirect land use change (ILUC) emissions of biofuels. •Natural gas fuels are estimated to be as carbon intensive as the petroleum fuels. •Policy ignores indirect emissions from natural gas.

  10. Hydrocarbon gas standards at the pmol/mol level to support ambient atmospheric measurements.

    Science.gov (United States)

    Rhoderick, George C; Duewer, David L; Ning, Li; DeSirant, Kathryn

    2010-02-01

    Studies of climate change increasingly recognize the diverse influences exerted by hydrocarbons in the atmosphere, including roles in particulates and ozone formation. Measurements of key non-methane hydrocarbons (NMHCs) suggest atmospheric concentrations ranging from low pmol/mol to nmol/mol, depending on location and compound. To accurately establish concentration trends and to relate measurement records from many laboratories and researchers, it is essential to have good calibration standards. Several of the world's National Metrology Institutes (NMIs) are developing primary and secondary reference gas standards at the nmol/mol level. While the U.S. NMI, the National Institute of Standards and Technology (NIST), has developed pmol/mol standards for halocarbons and some volatile organics, the feasibility of preparing well-characterized, stable standards for NMHCs at the pmol/mol level is not yet established. NIST recently developed a suite of primary standards by gravimetric dilution that contains 18 NMHCs covering the concentration range of 60 pmol/mol to 230 pmol/mol. Taking into account the small but chemically significant contribution of NMHCs in the high-purity diluent nitrogen used in their preparation, the relative concentrations and short-term stability (2 to 3 months) of these NMHCs in the primary standards have been confirmed by chromatographic analysis. The gravimetric values assigned from the methods used to prepare the materials and the analytical concentrations determined from chromatographic analysis generally agree to within +/-2 pmol/mol. However, anomalous results for several of the compounds reflect the difficulties inherent in avoiding contamination and making accurate measurements at these very low levels.

  11. Residue levels of organochlorines and mercury in Cattle Egret, Bubulcus ibis, eggs from the Faiyum Oasis, Egypt

    Energy Technology Data Exchange (ETDEWEB)

    Mullie, W.C. (Wageningen Agricultural Univ. (Netherlands) Foundation for Ornithological Research in Egypt, Belfort (Netherlands)); Massi, A.; Focardi, S.; Renzoni, A. (Universita di Siena (Italy))

    1992-05-01

    In Egypt, the Cattle Egret Bubulcus ibis is a common resident bird of the Nile Valley, the southern part of the Nile Delta, and the Suez Canal area. In the 1970s it disappeared as a breeding bird from the greater part of the Nile Delta, as did several other bird species, notably birds of prey. Only in recent years some of the species that had declined are markedly recovering, such as the Black-shouldered Kite Elanus caeruleus and the Cattle Egret. There is circumstancial evidence that these birds declined - at least partially - as a result of pesticide use in the main cotton growing areas, but this has never been substantiated. The recent recovery of some bird populations, commencing in the 1980s, coincides with a general shift from the use of organochlorines (except for endrin and HCH which are still in use) towards synthetic pyrethroids, organophosphates and carbamates in Egyptian agriculture: 30 million kg of formulated product annually, of which 70% are applied to cotton. The number of breeding pairs of Cattle Egrets in a well-known colony at Giza (30[degrees].01'N 31[degrees].13'E) steadily declined from 2500 in 1977 to 1100 in 1984. Therefore, it was decided to collect some eggs for residue analysis. Cattle Egrets are not piscivores, such as most other egrets, but mainly insectivores. They feed in agricultural areas and likely are good indicators for pesticide use in these habitats. Based on gizzard contents analysis, Kirkpatrick (1925) concluded that Cattle Egrets in Egypt only occasionally take (semi) aquatic prey, such as toads, and further predominantly Orthoptera and Diptera on arable land. Various studies have been published with respect to pesticides or heavy metals in the Egyptian environment but, surprisingly, birds have been almost completely ignored. The data presented are the first residue analyses of bird eggs from an agricultural area in Egypt, and as such they can be considered as baseline data for future research. 36 refs., 2 tabs.

  12. Trace analysis of residual methyl methanesulfonate, ethyl methanesulfonate and isopropyl methanesulfonate in pharmaceuticals by capillary gas chromatography with flame ionization detection.

    Science.gov (United States)

    Li, Weiyong

    2004-08-13

    A capillary gas chromatographic method using flame ionization detection was developed and validated for the trace analysis (ppm level) of methyl methanesulfonate, ethyl methanesulfonate, and isopropyl methanesulfonate in pharmaceutical drug substance. The method utilizes a megabore capillary column with bonded and crosslinked polyethylene glycol stationary phase. A dissolve-and-injection approach was adopted for sample introduction in a splitless mode. The investigated sample solvents include acetonitrile, ethyl acetate, methylene chloride, 1,2-dichloromethane, and toluene. Aqueous mixtures of acetonitrile and water can also be used as sample solvent. A limit of detection of about 1 microg/g (1 ppm) and limit of quantitation of 5 microg/g (5 ppm) were achieved for the mesylate esters in drug substance samples. The method optimization and validation are also discussed in this paper.

  13. Multiscale development of a fission gas thermal conductivity model: Coupling atomic, meso and continuum level simulations

    Science.gov (United States)

    Tonks, Michael R.; Millett, Paul C.; Nerikar, Pankaj; Du, Shiyu; Andersson, David; Stanek, Christopher R.; Gaston, Derek; Andrs, David; Williamson, Richard

    2013-09-01

    Fission gas production and evolution significantly impact the fuel performance, causing swelling, a reduction in the thermal conductivity and fission gas release. However, typical empirical models of fuel properties treat each of these effects separately and uncoupled. Here, we couple a fission gas release model to a model of the impact of fission gas on the fuel thermal conductivity. To quantify the specific impact of grain boundary (GB) bubbles on the thermal conductivity, we use atomistic and mesoscale simulations. Atomistic molecular dynamic simulations were employed to determine the GB thermal resistance. These values were then used in mesoscale heat conduction simulations to develop a mechanistic expression for the effective GB thermal resistance of a GB containing gas bubbles, as a function of the percentage of the GB covered by fission gas. The coupled fission gas release and thermal conductivity model was implemented in Idaho National Laboratory's BISON fuel performance code to model the behavior of a 10-pellet LWR fuel rodlet, showing how the fission gas impacts the UO2 thermal conductivity. Furthermore, additional BISON simulations were conducted to demonstrate the impact of average grain size on both the fuel thermal conductivity and the fission gas release.

  14. Multiscale development of a fission gas thermal conductivity model: Coupling atomic, meso and continuum level simulations

    International Nuclear Information System (INIS)

    Tonks, Michael R.; Millett, Paul C.; Nerikar, Pankaj; Du, Shiyu; Andersson, David; Stanek, Christopher R.; Gaston, Derek; Andrs, David; Williamson, Richard

    2013-01-01

    Fission gas production and evolution significantly impact the fuel performance, causing swelling, a reduction in the thermal conductivity and fission gas release. However, typical empirical models of fuel properties treat each of these effects separately and uncoupled. Here, we couple a fission gas release model to a model of the impact of fission gas on the fuel thermal conductivity. To quantify the specific impact of grain boundary (GB) bubbles on the thermal conductivity, we use atomistic and mesoscale simulations. Atomistic molecular dynamic simulations were employed to determine the GB thermal resistance. These values were then used in mesoscale heat conduction simulations to develop a mechanistic expression for the effective GB thermal resistance of a GB containing gas bubbles, as a function of the percentage of the GB covered by fission gas. The coupled fission gas release and thermal conductivity model was implemented in Idaho National Laboratory’s BISON fuel performance code to model the behavior of a 10-pellet LWR fuel rodlet, showing how the fission gas impacts the UO 2 thermal conductivity. Furthermore, additional BISON simulations were conducted to demonstrate the impact of average grain size on both the fuel thermal conductivity and the fission gas release

  15. The Effect of Exposure to Low Levels of Chlorine Gas on the Pulmonary Function and Symptoms in a Chloralkali Unit.

    Science.gov (United States)

    Neghab, Masoud; Amiri, Fatemeh; Soleimani, Esmaeel; Hosseini, Seyed Younus

    2016-01-01

    The present study was undertaken to ascertain whether (or not) long term occupational exposure to low (sub-TLV levels) atmospheric concentrations of chlorine gas was associated with any significant decrements in the parameters of pulmonary function and/or  increased prevalence of respiratory symptoms. In this retrospective cohort study that was performed in 2012, 54 workers of a local chloralkali unit and 38 non-exposed office staff were enrolled and compared. Atmospheric concentrations of chlorine gas were measured by numerous sampling with gas detector tubes. Data on respiratory symptoms were gathered using a standard questionnaire. Furthermore, spirometry test was performed for subjects both prior to and at the end of shift. Mean atmospheric concentration of chlorine gas was 0.27 ±0.05 ppm that was lower than the existing TLV value for this toxic irritant gas. Symptoms of respiratory diseases were significantly more frequent among exposed subjects than in referent individuals. Additionally, mean values of most parameters of pulmonary function including FEV1 (P=0.031), FEV1/FVC ratio (P=0.003) and PEF (P=0.005) were significantly lower than their corresponding values for unexposed subjects. Additional cross shift decrements were also noted in some lung functional capacities, although changes were not statistically significant. Exposure to sub-TLV levels of chlorine gas is associated with statistically significant decrements in the parameters of pulmonary function as well as increased prevalence of respiratory symptoms.

  16. Investigating the Possibility to Reduce the Residual Stress Level in 2.5D Cutting Using Titanium Coated Carbide Ball End Mill

    Directory of Open Access Journals (Sweden)

    N. Masmiati

    2014-01-01

    Full Text Available End milling is a multipoint cutting process in which material is removed from a workpiece by a rotating tool. It is widely used in cutting 2.5D profiles such as point-to-point, contouring, and pocketing operations. 2.5D machining possesses the capability to translate in all 3 axes but can perform the cutting operation in only 2 of the 3 axes at a time. This study focuses on optimizing the cutting parameters, such as machined surface inclinationangle, axial depth of cut, spindle speed, and feed rate for better surface integrity, namely, microhardness, residual stress, and microstructure in 2.5D cutting utilizing a titanium-coated carbide ball end mill. An optimization method known as Taguchi optimization, which includes planning, conducting, and analyzing results of matrix experiments, was used in order to achieve the best cutting parameter level. Data analysis was conducted using signal-to-noise (S/N and target performance measurement (TPM response analysis and analysis of variance (Pareto ANOVA. The optimum condition results obtained through analysis show improvements in microhardness of about 0.7%, residual stress in the feed direction of about 18.6%, and residual stress in the cutting direction of about 15.4%.

  17. PESTICIDE RESIDUES IN THE WATER AND FISH (LAGOON ...

    African Journals Online (AJOL)

    Liquid-liquid and liquid-solid extraction technique was employed to extract pesticide residues in water and fish samples, respectively, using 1:1 (v/v) ethyl acetate/dichloromethane mixture before being analyzed by gas chromatography. The highest level of pesticide contaminations was recorded in the Chemu lagoon as ...

  18. Development of multicomponent parts-per-billion-level gas standards of volatile toxic organic compounds

    International Nuclear Information System (INIS)

    Rhoderick, G.C.; Zielinski, W.L. Jr.

    1990-01-01

    This paper reports that the demand for stable, low-concentration multicomponent standards of volatile toxic organic compounds for quantifying national and state measurement of ambient air quality and hazardous waste incineration emissions has markedly increased in recent years. In response to this demand, a microgravimetric technique was developed and validated for preparing such standards; these standards ranged in concentration from several parts per million (ppm) down to one part per billion (ppb) and in complexity from one organic up to 17. Studies using the gravimetric procedure to prepare mixtures of different groups of organics. including multi-components mixtures in the 5 to 20 ppb range, revealed a very low imprecision. This procedure is based on the separate gravimetric introduction of individual organics into an evacuated gas cylinder, followed by the pressurized addition of a precalculated amount of pure nitrogen. Additional studies confirmed the long-term stability of these mixtures. The uncertainty of the concentrations of the individual organics at the 95% confidence level ranged from less than 1% relative at 1 ppm to less than 10% relative at 1 ppb. Over 100 primary gravimetric standards have been developed, validated, and used for certifying the concentrations of a variety of mixtures for monitoring studies

  19. Gas exchange and organic solutes in forage sorghum genotypes grown under different salinity levels

    Directory of Open Access Journals (Sweden)

    Daniela S. Coelho

    Full Text Available ABSTRACT Adaptation of plants to saline environments depends on the activation of mechanisms that minimize the effects of excess ions on vital processes, such as photosynthesis. The objective of this study was to evaluate the leaf gas exchange, chlorophyll, and organic solute in ten genotypes of forage sorghum irrigated with solutions of different salinity levels. The experiment was conducted in a randomized block design, in a 10 x 6 factorial arrangement, with three replications, using ten genotypes - F305, BRS-655, BRS-610, Volumax, 1.015.045, 1.016.005, 1.016.009, 1.016.013, 1.016.015 and 1.016.031 - and six saline solutions, with electrical conductivity (ECw of 0, 2.5, 5.0, 7.5, 10 and 12.5 dS m-1. The photosynthetic activity in forage sorghum plants reduces with increasing salinity, and this response was found in the ten genotypes evaluated. The chlorophyll and protein contents were not affected by salinity, whereas carbohydrates and amino acid contents increased with increasing ECw. Soluble sugars are essential for osmoregulation of forage sorghum due to its high content in leaves.

  20. Landscape-level variation in greenhouse gas emissions in vineyards of central California

    Science.gov (United States)

    Berbeco, M.; Steenwerth, K. L.; Jackson, L. E.; Higgins, C.; Yu, O.; Greenhut, R. F.; O'Geen, T.

    2011-12-01

    during pulse events (i.e., precipitation, irrigation, tillage) and that the magnitude of the differences will lessen with increased soil moisture and cooler temperatures in the winter. Though management such as tilling and irrigation can cause pulses of greenhouse gases from vineyard soils, our initial findings suggest that on a landscape level over longer time periods, differences between the soils and geologic history may be a better predictor of greenhouse gas emissions than management alone.

  1. Comparison of surface vacuum ultraviolet emissions with resonance level number densities. II. Rare-gas plasmas and Ar-molecular gas mixtures

    Energy Technology Data Exchange (ETDEWEB)

    Boffard, John B., E-mail: jboffard@wisc.edu; Lin, Chun C. [Department of Physics, University of Wisconsin, Madison, Wisconsin 53706 (United States); Wang, Shicong; Wendt, Amy E. [Department of Electrical and Computer Engineering, University of Wisconsin, Madison, Wisconsin 53706 (United States); Culver, Cody [Materials Science Program, University of Wisconsin, Madison, Wisconsin 53706 (United States); Radovanov, Svetlana; Persing, Harold [Applied Materials Inc., Gloucester, Massachusetts 01939 (United States)

    2015-03-15

    Vacuum ultraviolet (VUV) emissions from excited plasma species can play a variety of roles in processing plasmas, including damaging the surface properties of materials used in semiconductor processing. Depending on their wavelength, VUV photons can easily transmit thin upper dielectric layers and affect the electrical characteristics of the devices. Despite their importance, measuring VUV fluxes is complicated by the fact that few materials transmit at VUV wavelengths, and both detectors and windows are easily damaged by plasma exposure. The authors have previously reported on measuring VUV fluxes in pure argon plasmas by monitoring the concentrations of Ar(3p{sup 5}4s) resonance atoms that produce the VUV emissions using noninvasive optical emission spectroscopy in the visible/near-infrared wavelength range [Boffard et al., J. Vac. Sci. Technol., A 32, 021304 (2014)]. Here, the authors extend this technique to other rare-gases (Ne, Kr, and Xe) and argon-molecular gas plasmas (Ar/H{sub 2}, Ar/O{sub 2}, and Ar/N{sub 2}). Results of a model for VUV emissions that couples radiation trapping and the measured rare-gas resonance level densities are compared to measurements made with both a calibrated VUV photodiode and a sodium salicylate fluorescence detection scheme. In these more complicated gas mixtures, VUV emissions from a variety of sources beyond the principal resonance levels of the rare gases are found to contribute to the total VUV flux.

  2. LBA-ECO CD-02 Leaf Level Gas Exchange, Chemistry, and Isotopes, Amazonia, Brazil

    Data.gov (United States)

    National Aeronautics and Space Administration — ABSTRACT: This data set reports leaf gas flux and leaf properties from samples collected from trees, liana, pasture saplings, and pasture grass located at eight...

  3. LBA-ECO CD-02 Leaf Level Gas Exchange, Chemistry, and Isotopes, Amazonia, Brazil

    Data.gov (United States)

    National Aeronautics and Space Administration — This data set reports leaf gas flux and leaf properties from samples collected from trees, liana, pasture saplings, and pasture grass located at eight different...

  4. Six-month low level chlorine dioxide gas inhalation toxicity study with two-week recovery period in rats

    Directory of Open Access Journals (Sweden)

    Akamatsu Akinori

    2012-02-01

    Full Text Available Abstract Background Chlorine dioxide (CD gas has a potent antimicrobial activity at extremely low concentration and may serve as a new tool for infection control occupationally as well as publicly. However, it remains unknown whether the chronic exposure of CD gas concentration effective against microbes is safe. Therefore, long-term, low concentration CD gas inhalation toxicity was studied in rats as a six-month continuous whole-body exposure followed by a two-week recovery period, so as to prove that the CD gas exposed up to 0.1 ppm (volume ratio is judged as safe on the basis of a battery of toxicological examinations. Methods CD gas at 0.05 ppm or 0.1 ppm for 24 hours/day and 7 days/week was exposed to rats for 6 months under an unrestrained condition with free access to chow and water in a chamber so as to simulate the ordinary lifestyle in human. The control animals were exposed to air only. During the study period, the body weight as well as the food and water consumptions were recorded. After the 6-month exposure and the 2-week recovery period, animals were sacrificed and a battery of toxicological examinations, including biochemistry, hematology, necropsy, organ weights and histopathology, were performed. Results Well regulated levels of CD gas were exposed throughout the chamber over the entire study period. No CD gas-related toxicity sign was observed during the whole study period. No significant difference was observed in body weight gain, food and water consumptions, and relative organ weight. In biochemistry and hematology examinations, changes did not appear to be related to CD gas toxicity. In necropsy and histopathology, no CD gas-related toxicity was observed even in expected target respiratory organs. Conclusions CD gas up to 0.1 ppm, exceeding the level effective against microbes, exposed to whole body in rats continuously for six months was not toxic, under a condition simulating the conventional lifestyle in human.

  5. CURRENT LEVEL OF TECHNOLOGICAL DEVELOPMENT OF INTERNATIONAL OIL AND GAS COMPANIES

    Directory of Open Access Journals (Sweden)

    O. B. Lomakina

    2013-01-01

    Full Text Available In the article the questions of modern situation of the development of oil and gas branch of Russian economy are arisen with the accent to the problems, difficulties and role of high technologies in their overcoming. The comparative analysis of investment volumes and their efficiency in oil and gas branch of different countries is made. There is an attempt to investigate the reasons of the modern situation of this branch of economy and to give some recommendations.

  6. Bringing gas prices to economic levels. An overview of some of the barriers and challenges

    International Nuclear Information System (INIS)

    Dorssen, R. van

    1996-01-01

    This presentation is a general overview of the situation in Central and Eastern Europe regarding gas pricing. The experience in Central and Eastern Europe shows that many countries have embarked on the road towards a sound gas pricing. The speed of this differs among countries, depending on their specific circumstances. It has been a difficult process, despite the fact that all market players will benefit: the industry, the governments and the end consumers

  7. An assessment of natural radioactivity levels and radiation hazards for oil and gas production area

    International Nuclear Information System (INIS)

    Humbatov, F.Y.; Mustafayev, I.I.

    2017-01-01

    Natural radionuclides are always present in the earth's crust, whereas a large number of radionuclides are produced technologically during processes like oil and gas production. Mainly Uranium and thorium are present in the oil and gas source rocks. The water associated with the rock formation often contains radium along with chemically similar elements, such as strontium, barium and calcium due to their greater solubility than uranium and thorium under saline conditions. Radium isotopes, 226 Ra and 228 Ra are co-precipitated with barium and strontium salts from the formation water during the extraction and separation of the oil and gas. Every year a large amount of produced waters discharged from platforms to oil-gas production area. This process results in enhanced radium concentrations in both sludges and scales in pipes and other production equipment. The oil stream is further treated to remove the geological formation water that is extracted with the oil and gas. After separation from the oil, the formation water, also termed production water at this stage, is usually treated and discharged to the Caspian Sea or stored in oil and gas production area and forms produced water lake. Sand and oily sludge from the reservoir are also removed during this treatment. Solids deposit on the internal surfaces of the oil field extraction and production equipment, such as tubulars, other pipes, heat exchangers and pumps.

  8. Residuation theory

    CERN Document Server

    Blyth, T S; Sneddon, I N; Stark, M

    1972-01-01

    Residuation Theory aims to contribute to literature in the field of ordered algebraic structures, especially on the subject of residual mappings. The book is divided into three chapters. Chapter 1 focuses on ordered sets; directed sets; semilattices; lattices; and complete lattices. Chapter 2 tackles Baer rings; Baer semigroups; Foulis semigroups; residual mappings; the notion of involution; and Boolean algebras. Chapter 3 covers residuated groupoids and semigroups; group homomorphic and isotone homomorphic Boolean images of ordered semigroups; Dubreil-Jacotin and Brouwer semigroups; and loli

  9. Dechlorane Plus flame retardant in kingfishers (Alcedo atthis) from an electronic waste recycling site and a reference site, South China: influence of residue levels on the isomeric composition.

    Science.gov (United States)

    Mo, Ling; Wu, Jiang-Ping; Luo, Xiao-Jun; Sun, Yu-Xin; Zheng, Xiao-Bo; Zhang, Qiang; Zou, Fa-Shen; Mai, Bi-Xian

    2013-03-01

    Dechlorane Plus (DP) isomers were examined in common kingfishers (Alcedo atthis) and their prey fishes collected from an electronic waste (e-waste) recycling site and a reference site in South China, to investigate the possible influence of DP residue levels on the isomeric compositions. ∑DP (sum of syn-DP and anti-DP) concentrations in kingfishers from the e-waste recycling site ranged from 29 to 150 (median of 58) ng/g lipid weight (lw), which were one order of magnitude greater than those from the reference site (median = 3.9 ng/g lw). The isomer fractions of anti-DP (f(anti)) in kingfishers from the e-waste recycling site (mean of 0.65) were significantly smaller than those from the reference site (0.76). Additionally, the f(anti) values were negatively correlated to logarithm of ∑DP concentrations in the kingfishers (r(2) = 0.41, p < 0.0001). These results suggested that DP residue levels could influence its isomeric composition in the piscivorous bird. Copyright © 2012 Elsevier Ltd. All rights reserved.

  10. Output Feedback Dissipation Control for the Power-Level of Modular High-Temperature Gas-Cooled Reactors

    OpenAIRE

    Dong, Zhe

    2011-01-01

    Because of its strong inherent safety features and the high outlet temperature, the modular high temperature gas-cooled nuclear reactor (MHTGR) is the chosen technology for a new generation of nuclear power plants. Such power plants are being considered for industrial applications with a wide range of power levels, thus power-level regulation is very important for their efficient and stable operation. Exploiting the large scale asymptotic closed-loop stability provided by nonlinear controller...

  11. Proposed systematic methodology for analysis of Pb-210 radioactivity in residues produced in Brazilian natural gas pipes; Proposicao de um modelo analitico sistematico da atividade de Pb-210 em residuos gerados em linhas de gas

    Energy Technology Data Exchange (ETDEWEB)

    Ferreira, Aloisio Cordilha

    2003-11-15

    Since the 80's, the potential radiological hazards due to the handling of solid wastes contaminated with Rn-222 long-lived progeny - Pb-210 in special - produced in gas pipes and removed by pig operations have been subject of growing concern abroad our country. Nevertheless, little or no attention has been paid to this matter in the Brazilian plants up to now, being these hazards frequently underestimated or even ignored. The main purpose of this work was to propose a systematic methodology for analysis of Pb-210 radioactivity in black powder samples from some Brazilian plants, through the evaluation of direct Pb-210 gamma spectrometry and Bi-210 beta counting technical viabilities. In both cases, one in five samples of black powder analysed showed relevant activity (above 1Bq/kg) of Pb-210, being these results probably related to particular features of each specific plant (production levels, reservoir geochemical profile, etc.), in such a way that a single pattern is not observed. For the proposed methodology, gamma spectrometry proved to be the most reliable technique, showing a 3.5% standard deviation, and, for a 95% confidence level, overall fitness in the range of Pb-210 concentration of activity presented in the standard sample reference sheet, provided by IAEA for intercomparison purposes. In the Brazilian scene, however, the availability of statistically supported evidences is insufficient to allow the potential radiological hazard due to the management of black powder to be discarded. Thus, further research efforts are recommended in order to detect the eventually critical regions or plants where gas exploration, production and processing practices will require a regular program of radiological surveillance, in the near future. (author)

  12. Overexpression of hydroxynitrile lyase in cassava roots elevates protein and free amino acids while reducing residual cyanogen levels.

    Science.gov (United States)

    Narayanan, Narayanan N; Ihemere, Uzoma; Ellery, Claire; Sayre, Richard T

    2011-01-01

    Cassava is the major source of calories for more than 250 million Sub-Saharan Africans, however, it has the lowest protein-to-energy ratio of any major staple food crop in the world. A cassava-based diet provides less than 30% of the minimum daily requirement for protein. Moreover, both leaves and roots contain potentially toxic levels of cyanogenic glucosides. The major cyanogen in cassava is linamarin which is stored in the vacuole. Upon tissue disruption linamarin is deglycosylated by the apolplastic enzyme, linamarase, producing acetone cyanohydrin. Acetone cyanohydrin can spontaneously decompose at pHs >5.0 or temperatures >35°C, or is enzymatically broken down by hydroxynitrile lyase (HNL) to produce acetone and free cyanide which is then volatilized. Unlike leaves, cassava roots have little HNL activity. The lack of HNL activity in roots is associated with the accumulation of potentially toxic levels of acetone cyanohydrin in poorly processed roots. We hypothesized that the over-expression of HNL in cassava roots under the control of a root-specific, patatin promoter would not only accelerate cyanogenesis during food processing, resulting in a safer food product, but lead to increased root protein levels since HNL is sequestered in the cell wall. Transgenic lines expressing a patatin-driven HNL gene construct exhibited a 2-20 fold increase in relative HNL mRNA levels in roots when compared with wild type resulting in a threefold increase in total root protein in 7 month old plants. After food processing, HNL overexpressing lines had substantially reduced acetone cyanohydrin and cyanide levels in roots relative to wild-type roots. Furthermore, steady state linamarin levels in intact tissues were reduced by 80% in transgenic cassava roots. These results suggest that enhanced linamarin metabolism contributed to the elevated root protein levels.

  13. Performance of Pleurotus pulmonarius mushroom grown on maize stalk residues supplemented with various levels of maize flour and wheat bran

    Directory of Open Access Journals (Sweden)

    Senzosenkosi Surprise MKHIZE

    2017-10-01

    Full Text Available Abstract The use of supplemented agricultural waste in mushroom cultivation can be one of the environmentally friendly strategies for poverty alleviation. The study evaluated the performance of Pleurotus pulmonarius mushroom grown on maize stalk supplemented with varying levels of wheat bran (WB and maize flour (MF. A completely random design was used for the experiments. It was observed that Pleurotus pulmonarius was significantly affected by varying levels of supplementation, as 20% WB supplementation encountered higher contamination. The lower supplementation levels gave significantly shorter colonisation period with better mycelial growth rate (MGR. The 2% MF, 2% WB and 4% WB gave significantly higher MGR and faster colonisation. The shortest pinning time (TP was observed at the first flush with the minimum of 2 days. Higher supplementation levels gave maximum yield and biological efficiency (BE. With further increase of supplementation above a 12% WB and 14% MF, the BE and yield declined. Lower supplementation levels resulted in quicker colonisation period and improved growth rate, whereas high supplementation gave better production in terms of yield and BE. Therefore, for the purpose of maximum production, 12% WB and 14% MF may be recommended while for fast production time, 2% MF and 2% WB are recommended.

  14. Analysis of organo-chlorine pesticides residue in raw coffee with a modified "quick easy cheap effective rugged and safe" extraction/clean up procedure for reducing the impact of caffeine on the gas chromatography-mass spectrometry measurement.

    Science.gov (United States)

    Bresin, Bruno; Piol, Maria; Fabbro, Denis; Mancini, Maria Antonietta; Casetta, Bruno; Del Bianco, Clorinda

    2015-01-09

    The control of pesticide residues on raw coffee is a task of great importance due to high consumption of this beverage in Italy and in many other countries. High caffeine content can hamper extraction and measurement of any pesticide residue. A tandem extraction protocol has been devised by exploiting the quick easy cheap effective rugged and safe (QuEChERS) scheme for extraction, coupled to a dispersive liquid-liquid micro-extraction (DLLME) in order to drastically reduce caffeine content in the final extract. Gas chromatography-mass spectrometry (GC-MS) has been used for quantification of organo-chlorine pesticides in single ion monitoring (SIM) mode. Method has been validated and performances meet the criteria prescribed by European Union regulations. Copyright © 2014 Elsevier B.V. All rights reserved.

  15. Development and validation of a multi-residue method for the detection of a wide range of hormonal anabolic compounds in hair using gas chromatography-tandem mass spectrometry

    International Nuclear Information System (INIS)

    Rambaud, Lauriane; Monteau, Fabrice; Deceuninck, Yoann; Bichon, Emmanuelle; Andre, Francois; Le Bizec, Bruno

    2007-01-01

    The monitoring of anabolic steroid residues in hair is undoubtedly one of the most efficient strategies to demonstrate the long-term administration of these molecules in meat production animals. A multi-residue sample preparation procedure was developed and validated for 28 steroids. A 100 mg hair sample was grinded into powder and extracted at 50 deg. C with methanol. After acidic hydrolysis and extraction with ethyl acetate, phenolsteroids, such as estrogens, resorcyclic acid lactones and stilbens in one hand, are separated from androgens and progestagens in the other hand. Solid phase extractions were performed before applying a specific derivatisation for each compound sub-group. Detection and identification were achieved using gas chromatography-tandem mass spectrometry with acquisition in the selected reaction monitoring mode after electron ionisation. The method was validated according to the 2002/657/EC guideline. Decision limits (CCα) for main steroids were in the 0.1-10 μg kg -1 range

  16. Effects of delayed cord clamping on residual placental blood volume, hemoglobin and bilirubin levels in term infants: a randomized controlled trial.

    Science.gov (United States)

    Mercer, J S; Erickson-Owens, D A; Collins, J; Barcelos, M O; Parker, A B; Padbury, J F

    2017-03-01

    The objective of the study was to measure the effects of a 5-min delay (DCC) versus immediate cord clamping (ICC) on residual placental blood volume (RPBV) at birth, and hemoglobin and serum bilirubin at 24 to 48 h of age. In this prospective randomized controlled trial, 73 women with term (37 to 41 weeks) singleton fetuses were randomized to DCC (⩾5 min; n=37) or ICC (protocol violations. Cord milking was the proxy for DCC (n=11) when the provider could not wait. Infants randomized to DCC compared with ICC had significantly less RPBV (20.0 versus 30.8 ml kg -1 , Phemoglobin levels (19.4 versus 17.8 g dl -1 , P=0.002) at 24 to 48 h, with no difference in bilirubin levels. Term infants had early hematological advantage of DCC without increases in hyperbilirubinemia or symptomatic polycythemia.

  17. A multi-residue method for pesticides analysis in green coffee beans using gas chromatography-negative chemical ionization mass spectrometry in selective ion monitoring mode.

    Science.gov (United States)

    Pizzutti, Ionara R; de Kok, Andre; Dickow Cardoso, Carmem; Reichert, Bárbara; de Kroon, Marijke; Wind, Wouter; Weber Righi, Laís; Caiel da Silva, Rosselei

    2012-08-17

    In this study, a new gas chromatography-mass spectrometry (GC-MS) method, using the very selective negative chemical ionization (NCI) mode, was developed and applied in combination with a modified acetonitrile-based extraction method (QuEChERS) for the analysis of a large number of pesticide residues (51 pesticides, including isomers and degradation products) in green coffee beans. A previously developed integrated sample homogenization and extraction method for both pesticides and mycotoxins analysis was used. An homogeneous slurry of green milled coffee beans and water (ratio 1:4, w/w) was prepared and extracted with acetonitrile/acetic acid (1%), followed by magnesium sulfate addition for phase separation. Aliquots from this extract could be used directly for LC-MS/MS analysis of mycotoxins and LC-amenable pesticides. For GC-MS analysis, a further clean-up was necessary. C18- and PSA-bonded silica were tested as dispersive solid-phase extraction (d-SPE) sorbents, separate and as a mixture, and the best results were obtained using C18-bonded silica. For the optimal sensitivity and selectivity, GC-MS detection in the NCI-selected ion monitoring (SIM) mode had to be used to allow the fast analysis of the difficult coffee bean matrix. The validation was performed by analyzing recovery samples at three different spike concentrations, 10, 20 and 50 μg kg(-1), with 6 replicates (n=6) at each concentration. Linearity (r(2)) of calibration curves, estimated instrument and method limits of detection and limits of quantification (LOD(i), LOD(m), LOQ(i) and LOQ(m), respectively), accuracy (as recovery %), precision (as RSD%) and matrix effects (%) were determined for each individual pesticide. From the 51 analytes (42 parent pesticides, 4 isomers and 5 degradation products) determined by GC-MS (NCI-SIM), approximately 76% showed average recoveries between 70-120% and 75% and RSD ≤ 20% at the lowest spike concentration of 10 μg kg(-1), the target method LOQ. For the

  18. Multi-residue analysis of legacy POPs and emerging organic contaminants in Singapore's coastal waters using gas chromatography-triple quadrupole tandem mass spectrometry.

    Science.gov (United States)

    Zhang, Hui; Bayen, Stéphane; Kelly, Barry C

    2015-08-01

    A gas chromatography-triple quadrupole mass spectrometry (GC-MS/MS) based method was developed for determination of 86 hydrophobic organic compounds in seawater. Solid-phase extraction (SPE) was employed for sequestration of target analytes in the dissolved phase. Ultrasound assisted extraction (UAE) and florisil chromatography were utilized for determination of concentrations in suspended sediments (particulate phase). The target compounds included multi-class hydrophobic contaminants with a wide range of physical-chemical properties. This list includes several polycyclic and nitro-aromatic musks, brominated and chlorinated flame retardants, methyl triclosan, chlorobenzenes, organochlorine pesticides (OCPs) and polychlorinated biphenyls (PCBs). Spiked MilliQ water and seawater samples were used to evaluate the method performance. Analyte recoveries were generally good, with the exception of some of the more volatile target analytes (chlorobenzenes and bromobenzenes). The method is very sensitive, with method detection limits typically in the low parts per quadrillion (ppq) range. Analysis of 51 field-collected seawater samples (dissolved and particulate-bound phases) from four distinct coastal sites around Singapore showed trace detection of several polychlorinated biphenyl congeners and other legacy POPs, as well as several current-use emerging organic contaminants (EOCs). Polycyclic and nitro-aromatic musks, bromobenzenes, dechlorane plus isomers (syn-DP, anti-DP) and methyl triclosan were frequently detected at appreciable levels (2-20,000pgL(-1)). The observed concentrations of the monitored contaminants in Singapore's marine environment were generally comparable to previously reported levels in other coastal marine systems. To our knowledge, these are the first measurements of these emerging contaminants of concern in Singapore or Southeast Asia. The developed method may prove beneficial for future environmental monitoring of hydrophobic organic contaminants

  19. Biomass Production and Soil Carbon Level Changes in Various Tillage, Residue Management, and Cropping Systems in Moderately High Organic Matter Soils in Eastern South Dakota, U.S.A.

    Science.gov (United States)

    Woodard, H. J.; Bly, A.

    2003-12-01

    A four-year replicated field study was conducted in eastern South Dakota to assess the impact of maize (Zea mays L.), soybean (Glycine max L.), and spring wheat (Triticum aestivum L.) on crop residue accumulation and soil carbon when various tillage, crop residue management, and crop rotation scenarios were applied. Before planting, half the plots were chisel plowed and harrowed (tilled vs. no-till treatments). Corn-soybean, soybean-wheat, or corn-wheat-soybean rotations were established (rotation treatments). After grain harvest, crop residues were removed on half of the plots (residue-removed vs. residue-retained treatments). The range of initial soil carbon levels (loss by ignition method) for the 0-15cm depth was 1.7-3.0%. Post-harvest crop residue accumulation was greatest for the residue-retained treatment compared to the residue-removed treatment and for the no-till treatment compared to the tilled treatment. In addition, surface biomass accumulation was greatest when maize was part of a crop rotation. Maize can produce greater levels of biomass compared to either spring wheat or soybean. The least surface biomass accumulation was measured in the soybean-wheat rotation.

  20. Acclimation to Low Level Exposure of Copper in Bufo arenarum Embryos: Linkage of Effects to Tissue Residues

    Directory of Open Access Journals (Sweden)

    Cristina Silvia Pérez-Coll

    2007-06-01

    Full Text Available The acclimation possibilities to copper in Bufo arenarum embryos was evaluated by means of three different low level copper exposure conditions during 14 days. By the end of the acclimation period the copper content in control embryos was 1.04 ± 0.09 μg.g-1 (wet weight while in all the acclimated embryos a reduction of about 25% of copper was found. Thus copper content could be considered as a biomarker of low level exposure conditions. Batches of 10 embryos (by triplicate from each acclimation condition were challenged with three different toxic concentrations of copper. As a general pattern, the acclimation protocol to copper exerted a transient beneficial effect on the survival of the Bufo arenarum embryos. The acclimation phenomenon could be related to the selection of pollution tolerant organisms within an adaptive process and therefore the persistence of information within an ecological system following a toxicological stressor.

  1. [Plant drugs with residues of organochlorine compounds. 2. Identification of residues of DDT and its analogs by comparison of gas chromatography on packed and capillary columns and GC/MS coupling].

    Science.gov (United States)

    Benecke, R; Brotka, J; Wijsbeek, J; Franke, J P; Bruins, A P; de Zeeuw, R A

    1986-07-01

    For the GC analysis of DDT isomers and metabolites in extracts of Flores Chamomillae end Radix Valerianae the separation on a packed QF-1/OV-17 column was compared with various capillary columns of the CP-Sil type. Identification of the individual compounds could be achieved by comparing the retention behavior, chemical transformation of DDT and DDE, as well as by capillary GC-MS using single ion monitoring of substance-characteristic ion mass. In this way, residues of p,p'-DDT, o,p'-DDE and p,p'-TDE could be identified.

  2. The defect level and ideal thermal conductivity of graphene uncovered by residual thermal reffusivity at the 0 K limit.

    Science.gov (United States)

    Xie, Yangsu; Xu, Zaoli; Xu, Shen; Cheng, Zhe; Hashemi, Nastaran; Deng, Cheng; Wang, Xinwei

    2015-06-14

    Due to its intriguing thermal and electrical properties, graphene has been widely studied for potential applications in sensor and energy devices. However, the reported value for its thermal conductivity spans from dozens to thousands of W m(-1) K(-1) due to different levels of alternations and defects in graphene samples. In this work, the thermal diffusivity of suspended four-layered graphene foam (GF) is characterized from room temperature (RT) down to 17 K. For the first time, we identify the defect level in graphene by evaluating the inverse of thermal diffusivity (termed "thermal reffusivity": Θ) at the 0 K limit. By using the Debye model of Θ = Θ0 + C× e(-θ/2T) and fitting the Θ-T curve to the point of T = 0 K, we identify the defect level (Θ0) and determine the Debye temperature of graphene. Θ0 is found to be 1878 s m(-2) for the studied GF and 43-112 s m(-2) for three highly crystalline graphite materials. This uncovers a 16-43-fold higher defect level in GF than that in pyrolytic graphite. In GF, the phonon mean free path solely induced by defects and boundary scattering is determined as 166 nm. The Debye temperature of graphene is determined to be 1813 K, which is very close to the average theoretical Debye temperature (1911 K) of the three acoustic phonon modes in graphene. By subtracting the defect effect, we report the ideal thermal diffusivity and conductivity (κideal) of graphene presented in the 3D foam structure in the range of 33-299 K. Detailed physics based on chemical composition and structure analysis are given to explain the κideal-T profile by comparing with those reported for suspended graphene.

  3. Detection of residues in urine and tissues of sheep treated with trace levels of dietary ractopamine HCl

    Science.gov (United States)

    Ractopamine HCl was fed to sheep at 0 (Z), 0.001 (L), 0.01 (M), or 0.1 (H) mg/kg of diet (n = 4 per level, 0.5 kg of feed/day) for seven consecutive days and urine was collected daily about ~16 h post exposure. On-site lateral flow assays were able to reliably (0% false negatives) detect 20 ng of r...

  4. Microbial aspects of gas generation from low level radioactive waste simulant

    International Nuclear Information System (INIS)

    Kidby, D.W.; Billington, R.S.

    1992-01-01

    This report details the experimental work undertaken to further the understanding of the kinetics of methanogenesis associated with radioactive LLW disposal. A series of treatments were established by inoculating a LLW simulant and investigating the kinetics of methanogenesis in small Wheaton bottles. Treatments were set up to study the effects of waste compaction, the addition of metal to the simulant, the initial aerobic phase, pH and temperature on gas production. A separate experiment was also established to determine whether cellulose in the simulant acted as a biogas precursor. Results are presented from the head space gas analysis and the solid and liquid phase analyses undertaken over a 600 day period. (Author)

  5. Radiolytic gas generation from cement-based waste hosts for DOE low-level radioactive wastes

    International Nuclear Information System (INIS)

    Dole, L.R.; Friedman, H.A.

    1986-01-01

    Using cement-based immobilization binders with simulated radioactive waste containing sulfate, nitrate, nitrite, phosphate, and fluoride anions, the gamma- and alpha-radiolytic gas generation factors (G/sub t/, molecules/100 eV) and gas compositions were measured on specimens of cured grouts. These tests studied the effects of; (1) waste composition; (2) the sample surface-to-volume ratio; (3) the waste slurry particle size; and (4) the water content of the waste host formula. The radiolysis test vessels were designed to minimize the ''dead'' volume and to simulate the configuration of waste packages

  6. Levels of persistent organic pollutants and residual pattern of DDTs in small cetaceans from the coast of São Paulo, Brazil.

    Science.gov (United States)

    Yogui, G T; Santos, M C O; Bertozzi, C P; Montone, R C

    2010-10-01

    The State of São Paulo is the most developed area in Brazil and was impacted by persistent organic pollutants for several decades. This study investigated organochlorines in five species of small cetaceans (Pontoporia blainvillei, Stenella frontalis, Sotalia guianensis, Tursiops truncatus and Steno bredanensis) found dead along the coast of São Paulo between 1997 and 2003. DDTs (15.9 μg g(-1) lipid; mean for all pooled individuals) and PCBs (8.08 μg g(-1)) exhibited the highest concentrations in the animals, reflecting large amounts formerly used in Brazil. Lower levels of mirex (0.149 μg g(-1)), HCB (0.051 μg g(-1)), CHLs (0.008 μg g(-1)) and HCHs (0.007 μg g(-1)) were detected in all species. Residual pattern of DDTs in dolphins suggests that o,p'-DDT is more recalcitrant than p,p'-DDT in the body of the animals and/or the environment. In contrast to p,p'-DDT, residues of o,p'-DDT seem to be preferentially converted into o,p'-DDD rather than o,p'-DDE. Copyright © 2010 Elsevier Ltd. All rights reserved.

  7. A quantitative description of state-level taxation of oil and gas production in the continental U.S

    International Nuclear Information System (INIS)

    Weber, Jeremy G.; Wang, Yongsheng; Chomas, Maxwell

    2016-01-01

    We provide a quantitative description of state-level taxation of oil and gas production in the continental U.S. for 2004–2013. Aggregate revenues from production taxes nearly doubled in real terms over the period, reaching $10.3 billion and accounting for 20% of tax receipts in the top ten revenue states. The average state had a tax rate of 3.6%; nationally, the average dollar of production was taxed at 4.2%. The oil-specific rate estimated for the study period is $2.4 per barrel or $5.5 per ton of carbon. Lastly, state-level tax rates are two-thirds higher in states excluding oil and gas wells from local property taxes, suggesting that the policies are substitutes for one another. - Highlights: •State tax revenue from oil and gas production nearly doubled from 2004 to 2013. •Nationally, the typical dollar of production is taxed at 4.2%. •The rate applied to the typical dollar of production did not increase over time. •On average oil is taxed at $2.4 per barrel or $5.5 per ton of carbon. •State tax rates are two-thirds higher where oil and gas are not taxed as property.

  8. Mitigation of greenhouse gas emissions from reed canary grass in paludiculture: effect of groundwater level

    DEFF Research Database (Denmark)

    Karki, Sandhya; Elsgaard, Lars; Audet, Joachim

    2014-01-01

    Background and aims Combination of rewetting and wetland crop cultivation (paludiculture) is pursued as a wider carbon dioxide (CO2) mitigation option in drained peatland. However, information on the overall greenhouse gas (GHG) balance for paludiculture is lacking. We investigated the GHG balance...

  9. Two generators to produce SI-traceable reference gas mixtures for reactive compounds at atmospheric levels

    Science.gov (United States)

    Pascale, C.; Guillevic, M.; Ackermann, A.; Leuenberger, D.; Niederhauser, B.

    2017-12-01

    To answer the needs of air quality and climate monitoring networks, two new gas generators were developed and manufactured at METAS in order to dynamically generate SI-traceable reference gas mixtures for reactive compounds at atmospheric concentrations. The technical features of the transportable generators allow for the realization of such gas standards for reactive compounds (e.g. NO2, volatile organic compounds) in the nmol · mol-1 range (ReGaS2), and fluorinated gases in the pmol ṡ mol-1 range (ReGaS3). The generation method is based on permeation and dynamic dilution. The transportable generators have multiple individual permeation chambers allowing for the generation of mixtures containing up to five different compounds. This mixture is then diluted using mass flow controllers, thus making the production process adaptable to generate the required amount of substance fraction. All parts of ReGaS2 in contact with the gas mixture are coated to reduce adsorption/desorption processes. Each input parameter required to calculate the generated amount of substance fraction is calibrated with SI-primary standards. The stability and reproducibility of the generated amount of substance fractions were tested with NO2 for ReGaS2 and HFC-125 for ReGaS3. They demonstrate stability over 1-4 d better than 0.4% and 0.8%, respectively, and reproducibility better than 0.7% and 1%, respectively. Finally, the relative expanded uncertainty of the generated amount of substance fraction is smaller than 3% with the major contributions coming from the uncertainty of the permeation rate and/or of the purity of the matrix gas. These relative expanded uncertainties meet then the needs of the data quality objectives fixed by the World Meteorological Organization.

  10. Analyses of organochlorine pesticides residues in eels (Anguilla anguilla from Lake Garda using Gas chromatography coupled with Tandem Mass Spectrometry (GC-MS/MS.

    Directory of Open Access Journals (Sweden)

    Giuseppe Federico Labella

    2017-05-01

    Full Text Available Lake Garda is located in Insubria region, that is known for being the most populated and industrialized area of Italy (Camusso et al., 2001. Therefore, the Lake water, and also the fish species present, could be affected by environmental contamination.  European eel (Anguilla anguilla are considered as suitable matrix for biomonitoring environmental contaminants in European water (Belpaire et al., 2007, being widespread in many European waters and highly contaminated by lipophilic compounds, due to the high lipid content (up to 40% (Larsson et al., 1991. Moreover, eel is an edible species (its farming currently supplies approximately 45,000 tons/year (Nielsen et al., 2008, so it also represents a public health issue. Based on these considerations, the aim of this study was to evaluate the occurrence of fourteen organochlorine pesticides (OCs in forty-five eels (Anguilla anguilla from Lake Garda, using Accelerated Solvent Extraction (ASE procedure for the analytes extraction and Gas chromatography coupled with Tandem Mass Spectrometry (GC-MS/MS for the analysis of OCs. GC-MS/MS analysis was developed and validated according to the SANTE/11945/2015 guidelines.  Uncontaminated eel sample (previously checked for the presence of OCs and considered blank with a concentration of compounds < Limit of Detection were used for all procedure's optimization steps. For all the OCs analysed, satisfactory results were achieved. Regarding eel samples, several pesticides were detected, but DDTs (DDT and its metabolites were found with the highest prevalence (92 %. The concentration rage was from not detected (n.d. to 19000 ng g-1. Although DDTs levels in the environment are declining (Albaiges et al., 2011, they continue to bioaccumulate in tissues of human and animal and biomagnify in food chains.

  11. The relative contribution of waves, tides, and nontidal residuals to extreme total water levels on U.S. West Coast sandy beaches

    Science.gov (United States)

    Serafin, Katherine A.; Ruggiero, Peter; Stockdon, Hilary F.

    2017-01-01

    To better understand how individual processes combine to cause flooding and erosion events, we investigate the relative contribution of tides, waves, and nontidal residuals to extreme total water levels (TWLs) at the shoreline of U.S. West Coast sandy beaches. Extreme TWLs, defined as the observed annual maximum event and the simulated 100 year return level event, peak in Washington, and are on average larger in Washington and Oregon than in California. The relative contribution of wave-induced and still water levels (SWL) to the 100 year TWL event is similar to that of the annual maximum event; however, the contribution of storm surge to the SWL doubles across events. Understanding the regional variability of TWLs will lead to a better understanding of how sea level rise, changes in storminess, and possible changes in the frequency of major El Niños may impact future coastal flooding and erosion along the U.S. West Coast and elsewhere.

  12. The use of multilevel modeling and the level two residual file to explore the relationship between middle years programme student performance and diploma programme student performance.

    Science.gov (United States)

    Gordon, Melissa; Bergeron, Liz

    2015-03-01

    Multilevel modeling has recently found a substantial niche in the context of educational research, although several details about the methodological application of these models have yet to be explored in an achievement data framework. This paper makes use of data provided by the International Baccalaureate (IB) in order to investigate modeling decisions and certain applications of the level two residual file in an effort to increase understanding about the way linear and logistic multilevel models function. The focus of this research is on the relationship between performances in two IB programmes: the Middle Years Programme (MYP) and the Diploma Programme (DP). The impact of predictors on the interpretation of the unconditional and conditional variance-covariance matrix as well as the reliability coefficients is discussed. Empirical findings suggest that students who perform better during MYP moderation tend to perform better on DP exams. Copyright © 2014 Elsevier Inc. All rights reserved.

  13. Steady-State Flammable Gas Release Rate Calculation And Lower Flammability Level Evaluation For Hanford Tank Waste

    International Nuclear Information System (INIS)

    Hu, T.A.

    2007-01-01

    Assess the steady-state flammability level at normal and off-normal ventilation conditions. The methodology of flammability analysis for Hanford tank waste is developed. The hydrogen generation rate model was applied to calculate the gas generation rate for 177 tanks. Flammability concentrations and the time to reach 25% and 100% of the lower flammability limit, and the minimum ventilation rate to keep from 100 of the LFL are calculated for 177 tanks at various scenarios.

  14. Numerical simulation of interface movement in gas-liquid two-phase flows with Level Set method

    International Nuclear Information System (INIS)

    Li Huixiong; Chinese Academy of Sciences, Beijing; Deng Sheng; Chen Tingkuan; Zhao Jianfu; Wang Fei

    2005-01-01

    Numerical simulation of gas-liquid two-phase flow and heat transfer has been an attractive work for a quite long time, but still remains as a knotty difficulty due to the inherent complexities of the gas-liquid two-phase flow resulted from the existence of moving interfaces with topology changes. This paper reports the effort and the latest advances that have been made by the authors, with special emphasis on the methods for computing solutions to the advection equation of the Level set function, which is utilized to capture the moving interfaces in gas-liquid two-phase flows. Three different schemes, i.e. the simple finite difference scheme, the Superbee-TVD scheme and the 5-order WENO scheme in combination with the Runge-Kutta method are respectively applied to solve the advection equation of the Level Set. A numerical procedure based on the well-verified SIMPLER method is employed to numerically calculate the momentum equations of the two-phase flow. The above-mentioned three schemes are employed to simulate the movement of four typical interfaces under 5 typical flowing conditions. Analysis of the numerical results shows that the 5-order WENO scheme and the Superbee-TVD scheme are much better than the simple finite difference scheme, and the 5-order WENO scheme is the best to compute solutions to the advection equation of the Level Set. The 5-order WENO scheme will be employed as the main scheme to get solutions to the advection equations of the Level Set when gas-liquid two-phase flows are numerically studied in the future. (authors)

  15. STEADY-STATE FLAMMABLE GAS RELEASE RATE CALCULATION AND LOWER FLAMMABILITY LEVEL EVALUATION FOR HANFORD TANK WASTE

    Energy Technology Data Exchange (ETDEWEB)

    HU TA

    2007-10-26

    Assess the steady-state flammability level at normal and off-normal ventilation conditions. The methodology of flammability analysis for Hanford tank waste is developed. The hydrogen generation rate model was applied to calculate the gas generation rate for 177 tanks. Flammability concentrations and the time to reach 25% and 100% of the lower flammability limit, and the minimum ventilation rate to keep from 100 of the LFL are calculated for 177 tanks at various scenarios.

  16. Drought limitations to leaf-level gas exchange: results from a model linking stomatal optimization and cohesion-tension theory

    Science.gov (United States)

    Kimberly A. Novick; Chelcy F. Miniat; James M. Vose

    2016-01-01

    We merge concepts from stomatal optimization theory and cohesion–tension theory to examine the dynamics of three mechanisms that are potentially limiting to leaf-level gas exchange in trees during drought: (1) a ‘demand limitation’ driven by an assumption of optimal stomatal functioning; (2) ‘hydraulic limitation’ of water movement from the roots to the leaves...

  17. Damage structure in Nimonic PE16 alloy ion bombarded to high doses and gas levels

    International Nuclear Information System (INIS)

    Farrell, K.; Packan, N.H.

    1981-01-01

    The Nimonic PE16 alloy in solution-treated-and-aged condition was bombarded simultaneously with nickel ions and α and deuteron beams at 625 0 C to doses of 80 to 313 dpa at He/dpa = 10 and D/dpa = 25. Microstructural changes consisted of the introduction of dislocations and of cavities, and the redistribuion of γ' precipitates to these defects. Cavitational swelling remained below 1%. Cavities were represented by several distinct size classes, the smaller ones believed to be gas bubbles, and some larger ones associated with preferred growth of precipitate. Formation of bubbles at grain boundaries, and large cavities at incoherent twins intensified the possibility of mechanical separation of interfaces under high-gas irradiation conditions

  18. Residue processing

    Energy Technology Data Exchange (ETDEWEB)

    Gieg, W.; Rank, V.

    1942-10-15

    In the first stage of coal hydrogenation, the liquid phase, light and heavy oils were produced; the latter containing the nonliquefied parts of the coal, the coal ash, and the catalyst substances. It was the problem of residue processing to extract from these so-called let-down oils that which could be used as pasting oils for the coal. The object was to obtain a maximum oil extraction and a complete removal of the solids, because of the latter were returned to the process they would needlessly burden the reaction space. Separation of solids in residue processing could be accomplished by filtration, centrifugation, extraction, distillation, or low-temperature carbonization (L.T.C.). Filtration or centrifugation was most suitable since a maximum oil yield could be expected from it, since only a small portion of the let-down oil contained in the filtration or centrifugation residue had to be thermally treated. The most satisfactory centrifuge at this time was the Laval, which delivered liquid centrifuge residue and centrifuge oil continuously. By comparison, the semi-continuous centrifuges delivered plastic residues which were difficult to handle. Various apparatus such as the spiral screw kiln and the ball kiln were used for low-temperature carbonization of centrifuge residues. Both were based on the idea of carbonization in thin layers. Efforts were also being made to produce electrode carbon and briquette binder as by-products of the liquid coal phase.

  19. Dynamics of gas levels inside packages containing minimally processed Pera orange

    Directory of Open Access Journals (Sweden)

    Maria Cecília de Arruda Palharini

    2012-12-01

    Full Text Available The purpose of this study was to evaluate the changes in concentrations of O2 and CO2 inside packages of minimally processed Pera orange. Previously selected oranges that were washed, sanitized, and chilled were peeled using hydrothermal treatment (immersion of fruits in water at 50 °C for 8 minutes. The peeled oranges were then packed in five different plastic packages under passive and active modified atmosphere (5% O2 + 10% CO2 + 85% N2. The fruits were stored at 6 °C and 12 °C. The package headspace gas composition was evaluated for twelve days at 6 °C and nine days at 12 °C. The polypropylene film (32 µm promoted modified atmosphere similar to that initially injected (5% O2 + 10% CO2 + 85% N2 at 6 °C and 12 °C. With regard to the atmosphere modification system, the injection of a gas mixture anticipated achieving an equilibrium atmosphere inside the packages at 12 °C. At 6 °C, the gas composition inside the packages was kept close to that of the injection, but the equilibrium was not verified.

  20. Analysis of class 1 residual solvents in pharmaceuticals using headspace-programmed temperature vaporization-fast gas chromatography-mass spectrometry.

    Science.gov (United States)

    Pérez Pavón, José Luis; Del Nogal Sánchez, Miguel; Fernández Laespada, M A Esther; García Pinto, Carmelo; Moreno Cordero, Bernardo

    2007-02-02

    A sensitive method is presented for the fast screening and determination of residual class 1 solvents (1,1-dichloroethene, 1,2-dichloroethane, 1,1,1-trichloroethane, carbon tetrachloride and benzene) in pharmaceutical products. The applicability of a headspace (HS) autosampler in combination with GC equipped with a programmed temperature vaporizer (PTV) and a MS detector is explored. Different injection techniques were compared. The benefits of using solvent vent injection instead of split or splitless-hot injection for the measurement of volatile compounds are shown: better peak shapes, better signal-to-noise ratios, and hence better detection limits. The proposed method is extremely sensitive. The limits of detection ranged from 4.9 ppt (benzene) to 7.9 ppt (1,2-dichloroethane) and precision (measured as the relative standard deviation) was equal to or lower than 12% in all cases. The method was applied to the determination of residual solvents in nine different pharmaceutical products. The analytical performance of the method shows that it is appropriate for the determination of residual class 1 solvents and has much lower detection limits than the concentration limits proposed by the International Conference on Harmonization (ICH) of Technical Requirements for the Registration of Pharmaceuticals for Human Use. The proposed method achieves a clear improvement in sensitivity with respect to conventional headspace methods due to the use of the PTV.

  1. A rapid, solid phase extraction (SPE technique for the extraction and gas chromatographic determination lindane pesticide residue in tissue and milk

    Directory of Open Access Journals (Sweden)

    Yuningsih

    2006-03-01

    Full Text Available Organochlorine pesticide contamination in feed can cause residue in animal product (tissue and milk, so its become a problem in food safety. Solid phase extraction (SPE has been carried out for determination organochlorine pesticide residues in food animal production. The technique was rapid, not costly and produce limited amount of hazardous-waste. Samples were homogenized with acetonitrile trough cartridge C18, eluted in fluorocyl column with 2% ether-petroleum or acetonitrile fortissue and milk samples respectively. The recoveries of tissue sample by addition lindane standard solution: 0.50 and 1.00 μg are 85.10 and 103.10% respectively, while that of milk with the addition of 0.50, 1.00 and 1.50 μg are 83.80, 88.69 and 91.24% respectively. Three replicates were carried out for every sample. According of validation criteria of FAO/IAEA the recovery for analysis of pesticide residues was 70-110%. Therefore, the method is applicable.

  2. Effect of Magnesium on Gas Exchange and Photosynthetic Efficiency of Coffee Plants Grown under Different Light Levels

    Directory of Open Access Journals (Sweden)

    Kaio Gonçalves de Lima Dias

    2017-09-01

    Full Text Available The aim of the present study was to investigate the effects of magnesium on the gas exchange and photosynthetic efficiency of Coffee seedlings grown in nutrient solution under different light levels. The experiment was conducted under controlled conditions in growth chambers and nutrient solution at the Department of Plant Pathology of the Federal University of Lavras. The treatments consisted of five different Mg concentrations (0, 48, 96, 192 and 384 mg·L−1 and four light levels (80, 160, 240 and 320 µmol photon m−2·s−1. Both the Mg concentration and light levels affected gas exchange in the coffee plants. Photosynthesis increased linearly with the increasing light, indicating that the light levels tested were low for this crop. The highest CO2 assimilation rate, lowest transpiration, and highest water use efficiency were observed with 250 mg·Mg·L−1, indicating that this concentration was the optimal Mg supply for the tested light levels.

  3. Oxidative Stress and Genotoxicity of Long-Term Occupational Exposure to Low Levels of BTEX in Gas Station Workers

    Directory of Open Access Journals (Sweden)

    Feng Xiong

    2016-12-01

    Full Text Available Atmospheric benzene, toluene, ethylbenzene, and xylenes (BTEX can lead to multiple health injuries. However, what remains uncertain is the effect of long-term exposure to low levels of BTEX. Thus, we determined the BTEX levels in the air from the refueling and office areas in gas stations. Then we collected workers’ (200 refueling vs. 52 office workers peripheral blood samples to analyze the serum total-superoxide dismutase (T-SOD, glutathione (GSH, malondialdehyde (MDA, and 8-hydroxydeoxyguanosine (8-OHdG levels. DNA damage was analyzed by the comet assay and micronucleus test in buccal epithelial cells. We found that the levels of BTEX in refueling areas were significantly higher than those in office areas (p < 0.001. The serum T-SOD and GSH of refueling workers were significantly lower than those in office workers (p < 0.001. By contrast, the serum MDA and 8-OHdG of refueling workers were significantly higher than those of office workers (p < 0.001, MDA; p = 0.025, 8-OHdG. Furthermore, tail and Olive tail moments in refueling workers were longer (p = 0.004, tail moment; p = 0.001, Olive tail moment, and the micronucleus rate was higher (p < 0.001 than those in office workers. Taken together, long-term exposure to low levels of BTEX may reduce the antioxidant ability and increase the risk of DNA damage in refueling workers of gas stations.

  4. Management of NORM Residues

    International Nuclear Information System (INIS)

    2013-06-01

    The IAEA attaches great importance to the dissemination of information that can assist Member States in the development, implementation, maintenance and continuous improvement of systems, programmes and activities that support the nuclear fuel cycle and nuclear applications, and that address the legacy of past practices and accidents. However, radioactive residues are found not only in nuclear fuel cycle activities, but also in a range of other industrial activities, including: - Mining and milling of metalliferous and non-metallic ores; - Production of non-nuclear fuels, including coal, oil and gas; - Extraction and purification of water (e.g. in the generation of geothermal energy, as drinking and industrial process water; in paper and pulp manufacturing processes); - Production of industrial minerals, including phosphate, clay and building materials; - Use of radionuclides, such as thorium, for properties other than their radioactivity. Naturally occurring radioactive material (NORM) may lead to exposures at some stage of these processes and in the use or reuse of products, residues or wastes. Several IAEA publications address NORM issues with a special focus on some of the more relevant industrial operations. This publication attempts to provide guidance on managing residues arising from different NORM type industries, and on pertinent residue management strategies and technologies, to help Member States gain perspectives on the management of NORM residues

  5. Trained and consumer panel evaluation of sparkling wines sweetened to brut or demi sec residual sugar levels with three different sugars.

    Science.gov (United States)

    McMahon, Kenneth M; Diako, Charles; Aplin, Jesse; Mattinson, D Scott; Culver, Caleb; Ross, Carolyn F

    2017-09-01

    The dosage liquid, added at the final stage of sparkling wine production, imparts residual sweetness to the wine. No study has yet analyzed the influence of dosage composition on the final wine's sensory profile or consumer acceptance. In this study, dosage composition was altered through the addition of different sugar types (ST; fructose, glucose, or sucrose) to produce seven sparkling wines of varying residual sugar levels (RSL), including no sugar added, brut (5.3-8.4gST/L) or demi sec (34.9-37.8gST/L). As evaluated by a trained panel (n=9), the interaction between ST and RSL influenced the perception of caramelized/vanilla/honey (CVH) flavor, sweet taste, and sour taste attributes (pConsumers (n=126) also evaluated the sparkling wines and ST, RSL, and their interaction influenced consumer acceptance of different attributes, as well as the perception of the "refreshing" aspect of the wine (pconsumer acceptance of sparkling wines was highly correlated (r 2 ≤0.88) to CVH, floral, and fruity flavors, as well as sweet taste and creamy mouthfeel. External preference mapping revealed two clusters of consumers. Both consumer clusters liked wines sweetened with fructose, but Cluster 1 liked the demi sec sparkling wine sweetened with fructose (32.8g/L fructose) while Cluster 2 preferred the brut wine sweetened with fructose (8.4g/L fructose). These results suggest that consumer preference for sparkling wine was segmented based on sweetness preference. The results of this study offer winemakers knowledge about the influence of dosage composition on the sensory profile of sparkling wine. Copyright © 2017 Elsevier Ltd. All rights reserved.

  6. Modeling shock waves in an ideal gas: Going beyond the Navier-Stokes level

    International Nuclear Information System (INIS)

    Holian, B.L.; Patterson, C.W.; Mareschal, M.; Salomons, E.

    1993-01-01

    We model a shock wave in an ideal gas by solving a modified version of the compressible Navier-Stokes equations of hydrodynamics, where, following an earlier conjecture by Holian [Phys. Rev. A 37, 2562 (1988)], we use the temperature in the direction of shock propagation T xx , rather than the average temperature T=(T xx +T yy +T zz )/3, in the evaluation of the linear transport coefficients. The results are found to agree much better with the molecular-dynamics simulations of Salomons and Mareschal [Phys. Rev. Lett. 69, 269 (1992)] than standard Navier-Stokes theory

  7. SI-traceable and dynamic reference gas mixtures for water vapour at polar and high troposphere atmospheric levels

    Science.gov (United States)

    Guillevic, Myriam; Pascale, Céline; Mutter, Daniel; Wettstein, Sascha; Niederhauser, Bernhard

    2017-04-01

    In the framework of METAS' AtmoChem-ECV project, new facilities are currently being developed to generate reference gas mixtures for water vapour at concentrations measured in the high troposphere and polar regions, in the range 1-20 µmol/mol (ppm). The generation method is dynamic (the mixture is produced continuously over time) and SI-traceable (i.e. the amount of substance fraction in mole per mole is traceable to the definition of SI-units). The generation process is composed of three successive steps. The first step is to purify the matrix gas, nitrogen or synthetic air. Second, this matrix gas is spiked with the pure substance using a permeation technique: a permeation device contains a few grams of pure water in liquid form and loses it linearly over time by permeation through a membrane. In a third step, to reach the desired concentration, the first, high concentration mixture exiting the permeation chamber is then diluted with a chosen flow of matrix gas with one or two subsequent dilution steps. All flows are piloted by mass flow controllers. All parts in contact with the gas mixture are passivated using coated surfaces, to reduce adsorption/desorption processes as much as possible. The mixture can eventually be directly used to calibrate an analyser. The standard mixture produced by METAS' dynamic setup was injected into a chilled mirror from MBW Calibration AG, the designated institute for absolute humidity calibration in Switzerland. The used chilled mirror, model 373LX, is able to measure frost point and sample pressure and therefore calculate the water vapour concentration. This intercomparison of the two systems was performed in the range 4-18 ppm water vapour in synthetic air, at two different pressure levels, 1013.25 hPa and 2000 hPa. We present here METAS' dynamic setup, its uncertainty budget and the first results of the intercomparison with MBW's chilled mirror.

  8. STEADY STATE FLAMMABLE GAS RELEASE RATE CALCULATION & LOWER FLAMMABILITY LEVEL EVALUATION FOR HANFORD TANK WASTE [SEC 1 & 2

    Energy Technology Data Exchange (ETDEWEB)

    HU, T.A.

    2003-09-30

    Flammable gases such as hydrogen, ammonia, and methane are observed in the tank dome space of the Hanford Site high-level waste tanks. This report assesses the steady-state flammability level under normal and off-normal ventilation conditions in the tank dome space for 177 double-shell tanks and single-shell tanks at the Hanford Site. The steady-state flammability level was estimated from the gas concentration of the mixture in the dome space using estimated gas release rates, Le Chatelier's rule and lower flammability limits of fuels in an air mixture. A time-dependent equation of gas concentration, which is a function of the gas release and ventilation rates in the dome space, has been developed for both soluble and insoluble gases. With this dynamic model, the time required to reach the specified flammability level at a given ventilation condition can be calculated. In the evaluation, hydrogen generation rates can be calculated for a given tank waste composition and its physical condition (e.g., waste density, waste volume, temperature, etc.) using the empirical rate equation model provided in Empirical Rate Equation Model and Rate Calculations of Hydrogen Generation for Hanford Tank Waste, HNF-3851. The release rate of other insoluble gases and the mass transport properties of the soluble gas can be derived from the observed steady-state gas concentration under normal ventilation conditions. The off-normal ventilation rate is assumed to be natural barometric breathing only. A large body of data is required to do both the hydrogen generation rate calculation and the flammability level evaluation. For tank waste that does not have sample-based data, a statistical-based value from probability distribution regression was used based on data from tanks belonging to a similar waste group. This report (Revision 3) updates the input data of hydrogen generation rates calculation for 177 tanks using the waste composition information in the Best-Basis Inventory Detail

  9. Improved Screening Test for Idiopathic Infantile Hypercalcemia Confirms Residual Levels of Serum 24,25-(OH)2 D3 in Affected Patients.

    Science.gov (United States)

    Kaufmann, Martin; Morse, Nicole; Molloy, Billy Joe; Cooper, Donald P; Schlingmann, Karl Peter; Molin, Arnaud; Kottler, Marie Laure; Gallagher, J Christopher; Armas, Laura; Jones, Glenville

    2017-07-01

    CYP24A1 mutations are now accepted as a cause of idiopathic infantile hypercalcemia (IIH). A rapid liquid-chromatography tandem mass spectrometry (LC-MS/MS)-based blood test enabling measurement of the 25-OH-D 3 :24,25-(OH) 2 D 3 ratio (R) can identify IIH patients on the basis of reduced C24-hydroxylation of 25-OH-D 3 by CYP24A1 in vivo. Although values of this ratio are significantly elevated in IIH, somewhat surprisingly, serum 24,25-(OH) 2 D 3 remains detectable. The current study explores possible explanations for this including: residual CYP24A1 enzyme activity in individuals with certain CYP24A1 genotypes, expression of alternative C24-hydroxylases, and the possibility of isobaric contamination of the 24,25-(OH) 2 D 3 peak on LC-MS/MS. We employed an extended 20-min run time on LC-MS/MS to study serum vitamin D metabolites in patients with IIH due to mutations of CYP24A1 or SLC34A1; in unaffected heterozygotes and dialysis patients; in patients with vitamin D deficiency; as well as in normal subjects exhibiting a broad range of 25-OH-D levels. We identified 25,26-(OH) 2 D 3 as a contaminant of the 24,25-(OH) 2 D 3 peak. In normals, the concentration of 24,25-(OH) 2 D 3 greatly exceeds 25,26-(OH) 2 D 3 ; however, 25,26-(OH) 2 D 3 becomes more significant in IIH with CYP24A1 mutations and in dialysis patients, where 24,25-(OH) 2 D 3 levels are low when CYP24A1 function is compromised. Mean R in 30 IIH-CYP24A1 patients was 700 (range, 166 to 2168; cutoff = 140) as compared with 31 in 163 controls. Furthermore, patients possessing CYP24A1 L409S alleles exhibited higher 24,25-(OH) 2 D 3 levels and lower R (mean R = 268; n = 8) than patients with other mutations. We conclude that a chromatographic approach which resolves 24,25-(OH) 2 D 3 from 25,26-(OH) 2 D 3 produces a more accurate R that can be used to differentiate pathological states where CYP24A1 activity is altered. The origin of the residual serum 24,25-(OH) 2 D 3 in IIH patients appears to be

  10. Design of a compressed air modulator to be used in comprehensive multidimensional gas chromatography and its application in the determination of pesticide residues in grapes

    NARCIS (Netherlands)

    Pizzutti, I.R.; Vreuls, J.J.; Kok, A; Roehrs, R.; Martel, S.; Friggi, C.A.; Zanella, R.

    2009-01-01

    In this study, a new modulator that is simple, robust and presents low operation costs, was developed. This modulator uses compressed air to cool two small portions in the first centimeters of the second chromatographic column of a comprehensive multidimensional gas chromatography (GC × GC) system.

  11. Design and initial results from a kilojoule level Dense Plasma Focus with hollow anode and cylindrically symmetric gas puff.

    Science.gov (United States)

    Ellsworth, J L; Falabella, S; Tang, V; Schmidt, A; Guethlein, G; Hawkins, S; Rusnak, B

    2014-01-01

    We have designed and built a Dense Plasma Focus (DPF) Z-pinch device using a kJ-level capacitor bank and a hollow anode, and fueled by a cylindrically symmetric gas puff. Using this device, we have measured peak deuteron beam energies of up to 400 keV at 0.8 kJ capacitor bank energy and pinch lengths of ∼6 mm, indicating accelerating fields greater than 50 MV/m. Neutron yields of on the order of 10(7) per shot were measured during deuterium operation. The cylindrical gas puff system permitted simultaneous operation of DPF with a radiofrequency quadrupole accelerator for beam-into-plasma experiments. This paper describes the machine design, the diagnostic systems, and our first results.

  12. Numerical modeling of gas migration at a proposed repository for low and intermediate level nuclear wastes at Oberbauenstock, Switzerland

    International Nuclear Information System (INIS)

    Pruess, K.

    1990-03-01

    Hydrologic impacts of corrosive gas release from a hypothetical L/ILW nuclear waste repository at Oberbauenstock are explored by means of numerical simulation. A schematic two dimensional vertical section through the mountain is modeled with the simulator TOUGH, which describes two-phase flow of water and gas in porous and fractured media. Two reference cases are considered which represent the formations as a porous and as a fractured-porous (dual permeability) medium, respectively. Both cases predict similar and rather modest pressure increases, from ambient 10 bars to near 25 bars at the repository level. These results are to be considered preliminary because important parameters affecting two-phase flow, such as relative permeabilities of a fractured medium, are not well known at present. 24 refs., 15 figs., 5 tabs

  13. Comparison of high temperature gas particulate collectors for low level radwaste incinerator volume reduction systems

    International Nuclear Information System (INIS)

    Moscardini, R.L.; Johnston, J.R.; Waters, R.M.; Zievers, J.F.

    1983-01-01

    Incinerator system off-gases must be treated to prevent the release of particulates, noxious gases and radioactive elements to the environment. Fabric filters, venturi scrubbers, cyclone separators, an ceramic or metal filter candles have been used for particulate removal. Dry high temperature particulate collectors have the advantage of not creating additional liquid wastes. This paper presents a graphical comparison of different methods for filtering particles from high temperature incineration system off-gases. Eight methods of off-gas handling are compared. A much larger group may be present, but some judicious selection of different, but related systems was done for this paper based on experience with the Combustion Engineering Waste Incineration System (CE/WIS) Prototype. The eight types are: Inertial Devices, Electrostatic Precipitators (ESP), Standard Fabric Bags, Woven Ceramic Bags, Granular Beds, Sintered Metal Tubes, Felted Ceramic Bags and Ceramic Filter Candles. For high temperature LLRW particulate collection in incinerator off-gas systems, ceramic filter candles are the best overall choice

  14. Differing opinions about natural gas drilling in two adjacent counties with different levels of drilling activity

    International Nuclear Information System (INIS)

    Kriesky, J.; Goldstein, B.D.; Zell, K.; Beach, S.

    2013-01-01

    The pace of development of shale gas plays varies greatly among US states and globally. Through analysis of telephone survey responses, we explore support for natural gas drilling in residents of Washington County (WC), PA (n=502) vs. residents of Allegheny County (AC), PA (n=799). WC has had intense Marcellus Shale (MS) drilling activity, in comparison to adjacent AC, which has had little drilling activity. WC residents are marginally more supportive of MS drilling than are AC residents (p=0.0768). Residents of WC are more likely to perceive MS as an economic opportunity than are AC residents (p=0.0015); to be in a family that has signed a MS lease (p<0.0001); to follow the MS issue closely (p=0.0003); to get MS information from neighbors, friends, and relatives (p<0.0001); and are marginally less likely to perceive MS as an environmental threat (p=0.1090). WC leaseholders are significantly more supportive of MS drilling than WC non-leaseholders and AC non-leaseholders (p=0.0024). Mediation analyses show that county-based differences in support of MS drilling are due to WC residents seeing more of an economic opportunity in the MS and their greater likelihood of having a family-held lease. - Highlights: • Telephone survey analysis of sources of support for Marcellus Shale drilling. • Perceived positive economic impact of drilling drives support among respondents. • Mineral rights leaseholders are significantly more supportive than non-leaseholders

  15. Levels of radon gas concentration and progeny in homes of Potosi City, Bolivia to 4000 m

    International Nuclear Information System (INIS)

    Mamani M, R.; Claros J, J.; Vasquez A, R.

    2015-10-01

    Full text: In this work the presence of radon gas was determined, which is a radioactive contaminant that comes from underground, able to penetrate the houses. The danger is that when mixed air and when inhaled can cause serious damage to the lungs, for the short life time that has radon and progeny for decay, damaging the pulmonary alveoli and reducing breathing capacity of the habitants, then causing polycythemia in some cases. The study was carried out in homes in the city of Potosi, Bolivia located at 4000 m. The quantification of radon gas and progeny was performed with the equipment Alpha-Zaeller-2 (Az-2), quantification was realized in 6 zones of the city of Potosi, chosen randomly. In each zone were carried out measurements in 40 homes (2 rooms more permanent), both day and night, for a period of 3 days in two different seasons and with concentrations of average humidity of 20, 50 and 80%. The values obtained for each period vary depending on the season and 30 to 50% of the allowable values given by the EPA and Who for housing. (Author)

  16. Multi-class, multi-residue analysis of pesticides, polychlorinated biphenyls, polycyclic aromatic hydrocarbons, polybrominated diphenyl ethers and novel flame retardants in fish using fast, low-pressure gas chromatography-tandem mass spectrometry

    Energy Technology Data Exchange (ETDEWEB)

    Sapozhnikova, Yelena, E-mail: yelena.sapozhnikova@ars.usda.gov [US Department of Agriculture, Agricultural Research Service, Eastern Regional Research Center, 600 East Mermaid Lane, Wyndmoor, PA 193038 (United States); Lehotay, Steven J. [US Department of Agriculture, Agricultural Research Service, Eastern Regional Research Center, 600 East Mermaid Lane, Wyndmoor, PA 193038 (United States)

    2013-01-03

    Highlights: Black-Right-Pointing-Pointer A method for analysis of POPs and novel flame retardants in catfish was developed. Black-Right-Pointing-Pointer The method is based on a QuEChERS extraction, d-SPE clean-up and low pressure GC/MS-MS. Black-Right-Pointing-Pointer The method validation demonstrated good recoveries and low detection limits. Black-Right-Pointing-Pointer The method was successfully applied for analysis of catfish samples from the market. - Abstract: A multi-class, multi-residue method for the analysis of 13 novel flame retardants, 18 representative pesticides, 14 polychlorinated biphenyl (PCB) congeners, 16 polycyclic aromatic hydrocarbons (PAHs), and 7 polybrominated diphenyl ether (PBDE) congeners in catfish muscle was developed and evaluated using fast low pressure gas chromatography triple quadrupole tandem mass spectrometry (LP-GC/MS-MS). The method was based on a QuEChERS (quick, easy, cheap, effective, rugged, safe) extraction with acetonitrile and dispersive solid-phase extraction (d-SPE) clean-up with zirconium-based sorbent prior to LP-GC/MS-MS analysis. The developed method was evaluated at 4 spiking levels and further validated by analysis of NIST Standard Reference Materials (SRMs) 1974B and 1947. Sample preparation for a batch of 10 homogenized samples took about 1 h/analyst, and LP-GC/MS-MS analysis provided fast separation of multiple analytes within 9 min achieving high throughput. With the use of isotopically labeled internal standards, recoveries of all but one analyte were between 70 and 120% with relative standard deviations less than 20% (n = 5). The measured values for both SRMs agreed with certified/reference values (72-119% accuracy) for the majority of analytes. The detection limits were 0.1-0.5 ng g{sup -1} for PCBs, 0.5-10 ng g{sup -1} for PBDEs, 0.5-5 ng g{sup -1} for select pesticides and PAHs and 1-10 ng g{sup -1} for flame retardants. The developed method was successfully applied for analysis of catfish samples

  17. Effects of intensive induction and consolidation chemotherapy with idarubicin and high dose cytarabine on minimal residual disease levels in newly diagnosed adult precursor-B acute lymphoblastic leukemia

    Directory of Open Access Journals (Sweden)

    Kenneth F. Bradstock

    2016-12-01

    Full Text Available An intensive induction regimen, consisting of idarubicin and high dose cytarabine, was assessed in 19 adult patients, median age 44 years, with newly diagnosed precursor-B acute lymphoblastic leukemia (ALL. Patients achieving a complete response (CR were given an attenuated consolidation course. The primary endpoints were induction death rate and incidence of serious non-hematological toxicity. Grades 3–4 diarrhoea occurred in 47% of patients during induction. Two patients (11% died during induction therapy, and 2 were withdrawn due to resistant disease or prolonged marrow hypoplasia. Fifteen patients achieved CR (79%, but levels of minimal residual disease (MRD after induction were comparable with those previously observed using a modified pediatric protocol. Overall survival at 5 years was 36.8% while leukemia-free survival was 44.1%. An intensive AML protocol used in adults with ALL resulted in substantial toxicity and provided similar levels of cytoreduction to conventional ALL protocols, without improving long-term outcomes.

  18. [Residual levels in air, soil and soil-air exchange of organochlorine pesticides in Hami region of Xinjiang and its potential ecological risk].

    Science.gov (United States)

    Ma, Zi-Long; Mao, Xiao-Xuan; Ding, Zhong-Yuan; Gao, Hong; Huang, Tao; Tian, Hui; Guo, Qiang

    2013-03-01

    The concentrations of HCHs and DDTs in soil and air of urban/rural/forestry centre locations in the Hami region of Xinjiang were monitored for a year by passive atmospheric sampling in order to study the residual levels and air-soil exchange and evaluate ecological risk. The study results showed that the annual average concentrations of HCHs and DDTs in the air of Hami were 107.1 pg x m(-3) and 43.9 pg x m(-3), respectively, and the concentrations of HCHs and DDTs in summer and autumn were generally higher than those in winter and spring. It was deduced that the HCHs and DDTs tended to evaporate into the air because of the higher temperatures in summer and autumn. For OCPs in the air of study area, HCHs were dominanted the main pollution compared with DDTs. Meanwhile, alpha-HCH contributed the largest portion among all HCHs isomers, and p,p'-DDE dominated the residual levels of DDTs. Moreover, the values of alpha-HCH/gamma-HCH were in the range of 3 to 7, which indicated that the use of technical HCHs or the long distance atmosphere transport of HCHs may play a significant role for HCHs in the air of Hami region. Furthermore, ratios of (DDD + DDE)/DDTs were in the range of 0.4-0.9, 71.4% of which were higher than 0.5, indicating that DDTs in the air were mainly from historical usage and no new DDTs sources emerged in Hami recently. The concentrations of HCHs and DDTs in soil were between 0.344-6.954 ng x g(-1) and 0.104-26.397 ng x g(-1), respectively, which did not exceed the National Soil Quality Standard Level I. In addition, DDTs predominated in soil OCPs, in which beta-HCH accounting for a huge percentage in HCHs isomers, while o,p'-DDT predominated in pollution caused by DDTs isomers. From study results, it was also suggested that the important cause of DDTs residues in soil of Hami area could be the recent inputs of new sources since the value of (DDD + DDE)/DDTs were lower than 0.5. The sources of HCHs and DDTs in soil and atmosphere were not consistent

  19. International comparison of a hydrocarbon gas standard at the picomol per mol level.

    Science.gov (United States)

    Rhoderick, George C; Duewer, David L; Apel, Eric; Baldan, Annarita; Hall, Bradley; Harling, Alice; Helmig, Detlev; Heo, Gwi Suk; Hueber, Jacques; Kim, Mi Eon; Kim, Yong Doo; Miller, Ben; Montzka, Steve; Riemer, Daniel

    2014-03-04

    Studies of climate change increasingly recognize the diverse influences of hydrocarbons in the atmosphere, including roles in particulates and ozone formation. Measurements of key nonmethane hydrocarbons (NMHCs) suggest atmospheric mole fractions ranging from low picomoles per mol (ppt) to nanomoles per mol (ppb), depending on location and compound. To accurately establish mole fraction trends and to relate measurement records from many laboratories and researchers, it is essential to have accurate, stable, calibration standards. In February of 2008, the National Institute of Standards and Technology (NIST) developed and reported on picomoles per mol standards containing 18 nonmethane hydrocarbon compounds covering the mole fraction range of 60 picomoles per mol to 230 picomoles per mol. The stability of these gas mixtures was only characterized over a short time period (2 to 3 months). NIST recently prepared a suite of primary standard gas mixtures by gravimetric dilution to ascertain the stability of the 2008 picomoles per mol NMHC standards suite. The data from this recent chromatographic intercomparison of the 2008 to the 2011 suites confirm a much longer stability of almost 5 years for 15 of the 18 hydrocarbons; the double-bonded alkenes of propene, isobutene, and 1-pentene showed instability, in line with previous publications. The agreement between the gravimetric values from preparation and the analytical mole fractions determined from regression illustrate the internal consistency of the suite within ±2 pmol/mol. However, results for several of the compounds reflect stability problems for the three double-bonded hydrocarbons. An international intercomparison on one of the 2008 standards has also been completed. Participants included National Metrology Institutes, United States government laboratories, and academic laboratories. In general, results for this intercomparison agree to within about ±5% with the gravimetric mole fractions of the hydrocarbons.

  20. Using landfill gas as the primary fuel for a 200 WTPD thermal dryer[Held jointly with the 4. Canadian organic residuals and biosolids managment conference

    Energy Technology Data Exchange (ETDEWEB)

    Shulmister, D. [Manattee County, Manatee, FL (United States). Wastewater Division; Monroe, A. [McKim and Creed, Cary, NC (United States)

    2007-07-01

    Although there is no evidence of health problems, there is a growing opposition to class B land application of biosolids in many localities in the United States, resulting in less sites available to dispose of class B biosolids. Manatee County, located on the West Coast of Florida, decided to implement thermal drying of its biosolids. This produced a class A pellet that could be used without restriction as a fertilizer or soil amendment. The dryer will be located at the county's southeast water reclamation facility, adjacent to the county's Lena Road landfill. The methane gas from the landfill will be used as the primary fuel for the dryer. This paper presented how Manatee County, Florida decided to meet its long term biosolids handling and disposal needs. The paper provided background information on Manatee County, Florida. It discussed the reasons for the dryer technology selection, location of the dryer, sizing criteria as well as listing the components of the dryer. The paper also discussed dryer procurement. Other topics that were presented included fuel requirements and an analysis of landfill gas. The County expects to save approximately two million dollars per year by selecting landfill gas from its Lena Road landfill as the primary fuel for the dryer. 5 tabs.

  1. Residual risk

    African Journals Online (AJOL)

    ing the residual risk of transmission of HIV by blood transfusion. An epidemiological approach assumed that all HIV infections detected serologically in first-time donors were pre-existing or prevalent infections, and that all infections detected in repeat blood donors were new or incident infections. During 1986 - 1987,0,012%.

  2. Utilizing patch and site level greenhouse-gas concentration measurements in tandem with the prognostic model, ecosys

    Science.gov (United States)

    Morin, T. H.; Rey Sanchez, C.; Bohrer, G.; Riley, W. J.; Angle, J.; Mekonnen, Z. A.; Stefanik, K. C.; Wrighton, K. C.

    2016-12-01

    Estimates of wetland greenhouse gas (GHG) budgets currently have large uncertainties. While wetlands are the largest source of natural methane (CH4) emissions worldwide, they are also important carbon dioxide (CO2) sinks. Determining the GHG budget of a wetland is challenging, particularly because wetlands have intrinsically temporally and spatially heterogeneous land cover patterns and complex dynamics of CH4 production and emissions. These issues pose challenges to both measuring and modeling GHG budgets from wetlands. To improve wetland GHG flux predictability, we utilized the ecosys model to predict CH4 fluxes from a natural temperate estuarine wetland in northern Ohio. Multiple patches of terrain (that included Typha spp. and Nelumbo lutea) were represented as separate grid cells in the model. Cells were initialized with measured values but were allowed to dynamically evolve in response to meteorological, hydrological, and thermodynamic conditions. Trace gas surface emissions were predicted as the end result of microbial activity, physical transport, and plant processes. Corresponding to each model gridcell, measurements of dissolved gas concentrations were conducted with pore-water dialysis samplers (peepers). The peeper measurements were taken via a series of tubes, providing an undisturbed observation of the pore water concentrations of in situ dissolved gases along a vertical gradient. Non-steady state chambers and a flux tower provided both patch level and integrated site-level fluxes of CO2 and CH4. New Typha chambers were also developed to enclose entire plants and segregate the plant fluxes from soil/water fluxes. We expect ecosys to predict the seasonal and diurnal fluxes of CH4 from within each land cover type and to resolve where CH4 is generated within the soil column and its transmission mechanisms. We demonstrate the need for detailed information at both the patch and site level when using models to predict whole wetland ecosystem-scale GHG

  3. Impact of natural gas development in the Marcellus and Utica shales on regional ozone and fine particulate matter levels

    Science.gov (United States)

    Roohani, Yusuf H.; Roy, Anirban A.; Heo, Jinhyok; Robinson, Allen L.; Adams, Peter J.

    2017-04-01

    The Marcellus and Utica shale formations have recently been the focus of intense natural gas development and production, increasing regional air pollutant emissions. Here we examine the effects of these emissions on regional ozone and fine particulate matter (PM2.5) levels using the chemical transport model, CAMx, and estimate the public health costs with BenMAP. Simulations were performed for three emissions scenarios for the year 2020 that span a range potential development storylines. In areas with the most gas development, the 'Medium Emissions' scenario, which corresponds to an intermediate level of development and widespread adoption of new equipment with lower emissions, is predicted to increase 8-hourly ozone design values by up to 2.5 ppbv and average annual PM2.5 concentrations by as much as 0.27 μg/m3. These impacts could range from as much as a factor of two higher to a factor of three lower depending on the level of development and the adoption of emission controls. Smaller impacts (e.g. 0.1-0.5 ppbv of ozone, depending on the emissions scenario) are predicted for non-attainment areas located downwind of the Marcellus region such as New York City, Philadelphia and Washington, DC. Premature deaths for the 'Medium Emissions' scenario are predicted to increase by 200-460 annually. The health impacts as well as the changes in ozone and PM2.5 were all driven primarily by NOx emissions.

  4. Monitoring of Level of Radiation Hazards to the Community in the Settlement Around the Incandescent Gas Mantle Factory

    International Nuclear Information System (INIS)

    Suryawati

    2000-01-01

    The analyze of radiation internal hazards level of thoron (Rn-220) and its daughter to the community settlement around the incandescent gas mantle factory. The radiation hazard level can be indicated in the form of working level (WL) and sffsctive dose lungs received by the community. The working level and effective dose lungs is got from the measurement of radioactivity level of thoron (Rn-220) and its daugther and by using the mathematical formula calculation. The measurement of thoron radioactive concentration and its daughter. The value of woking level obtained, performance level for community range from 0,001-0,013 WL, equivalent with dose range from 0,014- 0,467 mSv. From the research result, it can be identified that the radiation hazard, because exceed the mean value of threshold thorium radioactive nuclide and its daughter product of natural radiation in back ground per year for word mean i.e. 0,336 mSv, but the value of this research result is far below the allowed value limit for the community is 0,12 WL and 1 mSv/year

  5. Clinical value of determination of changes of serum Gas, IL-2, IL-10 and IL-18 levels after transfusion of Red blood cells in patients with peptic ulcer

    International Nuclear Information System (INIS)

    Liu Tingting; Li Xinghua

    2011-01-01

    Objective: To investigation the changes of serum Gas, IL-2, IL-10 and IL-18 contents after transfusion of red blood cells in patients with peptic ulcer. Methods: Serum Gas, IL-2, IL-10 (with RIA), serum IL-18 (with ELISA) levels were measured in 31 patients with peptic ulcer and 35 controls. Results: Before transfusion,the serum IL-2 level in the patients was significantly lower than that in controls (P 0.05). Conclusion: Detection of serum Gas, IL-2, IL-10 and IL-18 levels is clinically useful for monitoring progress and favourable prognosis of patients with peptic ulcer possess important clinical value. (authors)

  6. Parameterization of Leaf-Level Gas Exchange for Plant Functional Groups From Amazonian Seasonal Tropical Rain Forest

    Science.gov (United States)

    Domingues, T. F.; Berry, J. A.; Ometto, J. P.; Martinelli, L. A.; Ehleringer, J. R.

    2004-12-01

    Plant communities exert strong influence over the magnitude of carbon and water cycling through ecosystems by controlling photosynthetic gas exchange and respiratory processes. Leaf-level gas exchange fluxes result from a combination of physiological properties, such as carboxylation capacity, respiration rates and hydraulic conductivity, interacting with environmental drivers such as water and light availability, leaf-to-air vapor pressure deficit, and temperature. Carbon balance models concerned with ecosystem-scale responses have as a common feature the description of eco-physiological properties of vegetation. Here we focus on the parameterization of ecophysiological gas-exchange properties of plant functional groups from a pristine Amazonian seasonally dry tropical rain forest ecosystem (FLONA-Tapajós, Santarém, PA, Brazil). The parameters were specific leaf weight, leaf nitrogen content, leaf carbon isotope ratio, maximum photosynthetic assimilation rate, photosynthetic carboxylation capacity, dark respiration rates, and stomatal conductance to water vapor. Our plant functional groupings were lianas at the top of the canopy, trees at the top of the canopy, mid-canopy trees and undestory trees. Within the functional groups, we found no evidence that leaves acclimated to seasonal changes in precipitation. However, there were life-form dependent distinctions when a combination of parameters was included. Top-canopy lianas were statistically different from top-canopy trees for leaf carbon isotope ratio, maximum photosynthetic assimilation rate, and stomatal conductance to water vapor, suggesting that lianas are more conservative in the use of water, causing a stomatal limitation on photosynthetic assimilation. Top-canopy, mid canopy and understory groupings were distinct for specific leaf weight, leaf nitrogen content, leaf carbon isotope ratio, maximum photosynthetic assimilation rate, and photosynthetic carboxylation capacity. The recognition that plant

  7. Leveling off the energy demand. Air conditioning by town gas NEXT STAGE. Energy juyo no heijunka wo motomete. Gas reibo NEXT STAGE

    Energy Technology Data Exchange (ETDEWEB)

    Watanabe, K. (Keio Univ., Tokyo (Japan). Faculty of Science and Technology)

    1994-07-01

    Utilizing various types of energy with combining them rationally is now drawing attention. One of these types of energy is the town gas. The air conditioning by town gas draws a special attention. The town gas is characterized by environmental conservation, energy saving, and comfortability. The town gas does not contain sulfur compounds which cause the acid rain. The town gas produces the least amount of carbon dioxide among all the fossil fuel. The air conditioning by the town gas is getting popular. Examples are Tokyo Dome in Tokyo, Pavilion Plaza, a new shopping spot in Fukuoka, Umeda Sky Building in Osaka, Dai-ich Apparel Center in Tokyo, Ohno Memorial Hospital in Osaka, Nagoya Municipal Integrated Stadium in Nagoya, Meguro-Gajoen in Tokyo, and New Yomiuri-Shimbun Building in Sapporo. 41 figs.

  8. Gas chromatography and isotope ratio mass spectrometry of Pinot Noir wine volatile compounds (δ13C) and solid residues (δ13C, δ15N) for the reassessment of vineyard water-status.

    Science.gov (United States)

    Spangenberg, Jorge E; Vogiatzaki, Maria; Zufferey, Vivian

    2017-09-29

    This paper describes a novel approach to reassess the water status in vineyards based on compound-specific isotope analysis (CSIA) of wine volatile organic compounds (δ 13 C VOC/VPDB ) and bulk carbon and nitrogen isotopes, and the C/N molar ratios of the wine solid residues (δ 13 C SR/VPDB , δ 15 N SR/Air-N2 ). These analyses link gas chromatography/combustion and elemental analysis to isotope ratio mass spectrometry (GC/C/IRMS, EA/IRMS). Field-grown cultivars of Pinot Noir grapevines were exposed during six growing seasons (2009-2014) to controlled soil water availability, while maintaining identical the other environmental variables and agricultural techniques. Wines were produced from the grapes by the same oenological protocol. This permitted for the assessment of the effects in the biochemistry of wines solely induced by the changes in the plant-soil water status. This mimicked the more recurrent and prolonged periods of soil water deficiency due to climate changes. Water stress in grapevine was assessed by the measurement of the predawn leaf water potential (Ψ pd ) and the stable carbon isotope composition of the berry sugars during harvest (must sugars). For quantitation purposes and the normalization of the measured stable carbon isotope ratios of the VOCs, the wine samples were spiked with three standard compounds with known concentration and δ 13 C VPDB values. VOCs were extracted by liquid-liquid extraction and analyzed by gas chromatography/flame ionization detection (GC/FID), gas chromatography/mass spectrometry (GC/MS), and GC/C/IRMS. δ 13 C values were obtained for eighteen VOCs. The solid residues were obtained by freeze-drying wine aliquots and were analyzed for their C and N content and isotope composition by EA/IRMS. All the isotopic ratios (δ 13 C SR , δ 15 N SR , δ 13 C VOC ) are highly correlated with the Ψ pd values, indicating that the proposed gas chromatography and isotope ratio mass spectrometry approach is a useful tool to

  9. Gas Exchange Characteristics in Tectona grandis L. Clones under Varying Concentrations of CO2 Levels

    Directory of Open Access Journals (Sweden)

    S. Saravanan

    2014-08-01

    Full Text Available The Institute of Forest Genetics and Tree Breeding, Coimbatore, India functioning under the Indian Council of Forestry Research and Education, Dehara Dun, has a long term systematic tree improvement program for Tectona grandis aimed to enhancing productivity and screening of clones for site specific. In the process, twenty clones of T. grandis L. were studied for the physiological parameters and water use efficiency with reference to the elevated CO2 levels. CO2 enrichment studies in special chambers help in understanding the changes at individual level, and also at physiological, biochemical and genetic level. It also provides valuable information for establishing plantations at different geographic locations. Considerable variations were observed when the selected 20 clones of T. grandis were subjected to physiological studies under elevated CO2 conditions (600 and 900 mol mol-1. Eight clones exhibited superior growth coupled with favorable physiological characteristics including high photosynthetic rate, carboxylation and water use efficiency under elevated CO2 levels. Clones with minimal variation in physiological characteristics under elevated levels of CO2 suggest their ability to overcome physiological stresses and adapt to varying climatic conditions.

  10. Methodology for the determination of residues of organophosphorous pesticides in milk of domestic consumption by means of gas chromatography and extraction in solid phase

    International Nuclear Information System (INIS)

    Romero Blanco, Eric; Meza Nunez, Humberto; Poveda Calvo, Vanessa

    2005-01-01

    A new method oriented to the detection and quantification of 15 organophosphate pesticide in raw milk samples for national consumption has been developed by using a gas chromatograph equipped with polydimethylsiloxane capillary column and a nitrogen-phosphorus detector (NPD), in combination with the extraction technique in solid phase (SPE) for the sample cleaning process and pesticide extraction. Recovery percentages obtained were close to 100% and the detection limits obtained were lower than 20 μg/L for 13 of the organophosphates analyzed. Overall, the method showed important improvement as compared to conventional liquid/liquid extraction methodologies. (Author) [es

  11. Composition of carbonization residues

    Energy Technology Data Exchange (ETDEWEB)

    Hupfer; Leonhardt

    1943-11-27

    This report compared the composition of samples from Wesseling and Leuna. In each case the sample was a residue from carbonization of the residues from hydrogenation of the brown coal processed at the plant. The composition was given in terms of volatile components, fixed carbon, ash, water, carbon, hydrogen, oxygen, nitrogen, volatile sulfur, and total sulfur. The result of carbonization was given in terms of (ash and) coke, tar, water, gas and losses, and bitumen. The composition of the ash was given in terms of silicon dioxide, ferric oxide, aluminum oxide, calcium oxide, magnesium oxide, potassium and sodium oxides, sulfur trioxide, phosphorus pentoxide, chlorine, and titanium oxide. The most important difference between the properties of the two samples was that the residue from Wesseling only contained 4% oil, whereas that from Leuna had about 26% oil. Taking into account the total amount of residue processed yearly, the report noted that better carbonization at Leuna could save 20,000 metric tons/year of oil. Some other comparisons of data included about 33% volatiles at Leuna vs. about 22% at Wesseling, about 5 1/2% sulfur at Leuna vs. about 6 1/2% at Leuna, but about 57% ash for both. Composition of the ash differed quite a bit between the two. 1 table.

  12. Development and validation of a multi-residue method for the detection of a wide range of hormonal anabolic compounds in hair using gas chromatography-tandem mass spectrometry

    Energy Technology Data Exchange (ETDEWEB)

    Rambaud, Lauriane [LABERCA, Ecole Nationale Veterinaire de Nantes, Route de Gachet, BP50707, 44307 Nantes Cedex 3 (France); Monteau, Fabrice [LABERCA, Ecole Nationale Veterinaire de Nantes, Route de Gachet, BP50707, 44307 Nantes Cedex 3 (France); Deceuninck, Yoann [LABERCA, Ecole Nationale Veterinaire de Nantes, Route de Gachet, BP50707, 44307 Nantes Cedex 3 (France); Bichon, Emmanuelle [LABERCA, Ecole Nationale Veterinaire de Nantes, Route de Gachet, BP50707, 44307 Nantes Cedex 3 (France); Andre, Francois [LABERCA, Ecole Nationale Veterinaire de Nantes, Route de Gachet, BP50707, 44307 Nantes Cedex 3 (France); Le Bizec, Bruno [LABERCA, Ecole Nationale Veterinaire de Nantes, Route de Gachet, BP50707, 44307 Nantes Cedex 3 (France)]. E-mail: lebizec@vet-nantes.fr

    2007-03-14

    The monitoring of anabolic steroid residues in hair is undoubtedly one of the most efficient strategies to demonstrate the long-term administration of these molecules in meat production animals. A multi-residue sample preparation procedure was developed and validated for 28 steroids. A 100 mg hair sample was grinded into powder and extracted at 50 deg. C with methanol. After acidic hydrolysis and extraction with ethyl acetate, phenolsteroids, such as estrogens, resorcyclic acid lactones and stilbens in one hand, are separated from androgens and progestagens in the other hand. Solid phase extractions were performed before applying a specific derivatisation for each compound sub-group. Detection and identification were achieved using gas chromatography-tandem mass spectrometry with acquisition in the selected reaction monitoring mode after electron ionisation. The method was validated according to the 2002/657/EC guideline. Decision limits (CC{alpha}) for main steroids were in the 0.1-10 {mu}g kg{sup -1} range.

  13. Doses de boro e água residuária na produção do girassol Levels of boron and wastewater in production of sunflower

    Directory of Open Access Journals (Sweden)

    José Amilton Santos Junior

    2011-12-01

    Full Text Available A disponibilidade hídrica de qualidade tem se tornado em todo o mundo, um dos principais entraves à expansão das fronteiras agrícolas. Dentro deste contexto o presente trabalho teve como objetivo avaliar os efeitos de doses de boro e da irrigação com dois tipos de água, residuária e de abastecimento, nos componentes de produção do girassol (Helianthus annuus L. cv. EMBRAPA 122/V-2000. A pesquisa foi realizada em ambiente protegido da Universidade Federal de Campina Grande, em delineamento em blocos casualizados, analisados em esquema fatorial 5 x 2 sendo cinco doses de boro (0 - testemunha; 1,0; 2,0; 3,0 e 4,0 mg L-1 combinados com dois tipos de água de irrigação (R - residuária e AB - abastecimento, com três repetições. A análise estatística compreendeu análises de variância (teste F e as médias foram comparadas pelo teste de Tukey para comparar os fatores qualitativos em 0,05 de probabilidade. Verificou-se que as doses de boro e tipos de água utilizados não influenciaram nenhuma variável ligada à produção de aquênios; no entanto, a irrigação com água residuária influenciou positivamente as variáveis fitomassa fresca e seca das folhas, do caule e da parte aérea, todas ligadas à produção de forragem.The availability of water of quality has become worldwide, a major constraint to expanding agricultural frontiers. Within this context, this study aimed to evaluate the effects of boron doses and irrigation with two types of water, wastewater and municipal supply water, on yield components of sunflower (Helianthus annuus L. cv. EMBRAPA 122/V-2000. The study was conducted in a greenhouse at the Federal University of Campina Grande, in a randomized block design, analyzed in a 5 x 2 factorial with five B of boron (0; 1.0; 2.0; 3.0 and 4.0 mg L-1 combined with two types of irrigation water (R - wastewater and AB - municipal supply water with three replications. Statistical analysis consisted of analysis of variance

  14. Quantification of trace level of fluoride content in uranium oxide produced by deconversion of HEX gas by ion chromatography

    International Nuclear Information System (INIS)

    Unnikrishnan, E.K.; Padmakumar, P.R.; Shanmugavelu, P.; Sudhakar, T.M.; Bhowmik, A.

    2015-01-01

    Fluoride content in nuclear fuel is detrimental due to its corrosion behavior with cladding material. It is essential to monitor and control the fluoride concentration in nuclear material at various processing stages. Deconversion of upgraded HEX gas is carried out to produce uranium oxide. The performance of the deconversion process of HEX gas is evaluated for which trace level of fluoride concentration accompanying uranium oxide is considered as a marker. An analytical method has been developed for testing the uranium oxide produced from deconversion process of HEX gas. The method involves sample pretreatment followed by analysis using ion chromatography. The test method was validated for its performance using in house synthetic uranyl fluoride (UO 2 F 2 ) standard solutions prepared with different level of fluoride content. The results are in agreement with the expected values with the recovery in the range of 80-95%. This method has been successfully implemented for routine analysis of samples at our lab. Since UO 2 F 2 reference material is not available to validate this method, in house UO 2 F 2 standards were prepared from U 3 O 8 prepared from nuclear grade uranyl nitrate solution. UO 2 F 2 standards were prepared by converting U 3 O 8 to UO 2 F 2 by the addition of HF followed by H 2 O 2 at 200°C on a hot plate. The entire yellow colored UO 2 F 2 was dissolved in nano pure water and recrystallised several times to ensure that all free HF is removed. The crystals dried in air oven at 120° for three hours. Samples containing 1000 mg kg -1 fluoride prepared from this UO 2 F 2 , and subsequently from this sample containing 5 mg kg -1 to 35 mg kg -1 fluoride samples were prepared and analysed against fluoride CRM and the fluoride concentration obtained was analysed

  15. Permissible level of toxaphene residues in fish from the German market based on in vivo and in vitro effects to tumor promotion.

    Science.gov (United States)

    Ekici, Perihan; Friess, Albrecht; Parlar, Harun

    2008-07-01

    Toxaphene is a chlorinated pesticide consisting of more than 200 congeners that are mainly chlorobornanes and chlorocamphenes. As the congeners exhibit different stability properties in the environment, only between 20 and 30 compounds can be observed in, e.g., fish, which are represented by technical toxaphene as a mixture. In human body, the congeners Parlar #26, #40, #41, #44, #50, and #62 are detected frequently. Three of them, #26, #50, and #62, pose a potential risk to human health due to their persistent characteristic. By using experimental results of a European Union study (MATT, 2000. Investigation into the Monitoring, Analysis and Toxicity of Toxaphene in Marine Foodstuffs, European Union, Brussels, Final report, FAIR CT PL.96.3131. Investigation into the Monitoring, Analysis and Toxicity of Toxaphene in Marine Foodstuffs), a reference dose related to tumor promotion was calculated for these representative persistent toxaphene congeners. In Germany, the sum of the congeners #26, #50, and #62 is defined as the official standard for toxaphene residues in food. In this work, different fish samples obtained from German markets were studied regarding their contamination with toxaphene congeners, presented either in sum, or as single constitutes. The obtained data were used to define the acceptable total concentration of the sum of Parlar #26, #50, and #62 with regard to prevention of tumor promotion in human. The results showed that the currently existing permissible level of the sum of these congeners (0.1 mg/kg) is higher than the acceptable concentration in fish samples determined by this work and calculated at ca. 0.090 mg/kg. It is therefore recommended to improve the permissible level of toxaphene in German food samples.

  16. Effect of different formulations on tebuconazole residues in stone fruits.

    Science.gov (United States)

    Lucini, Luigi; Molinari, Gian Pietro

    2009-04-01

    The correlation between pesticide residue levels and formulation of an active substance is often not considered, even if it is reasonable to expect some differences arising from behaviour during dilution and spraying, from adhesion to plant and from degradation. An experimental study to investigate the magnitude of tebuconazole residues as a function of different tebuconazole formulated products was carried out in Italy. The fungicide was applied as wettable powder (WP) and water-dispersible granule (WG) formulations to peach, plum, apricot and nectarine orchards, on four different sites. The fruit samples gained from the field trials were quantitatively analysed by gas chromatography with a nitrogen phosphorus detector (GC/NPD) for tebuconazole residues. Tebuconazole residues in the fruits gained from the plot treated with the WP formulation, 14 days after application, were in the range 0.01-0.07 mg kg(-1), while corresponding residues in the plot treated with the WG formulation were in the range 0.01-0.06 mg kg(-1). No significant differences in the residue levels of tebuconazole could be observed between the trials conducted with the WP and the WG formulation. Copyright (c) 2009 Society of Chemical Industry.

  17. Analysis of trace levels of impurities and hydrogen isotopes in helium purge gas using gas chromatography for tritium extraction system of an Indian lead lithium ceramic breeder test blanket module.

    Science.gov (United States)

    Devi, V Gayathri; Sircar, Amit; Yadav, Deepak; Parmar, Jayraj

    2018-01-12

    In the fusion fuel cycle, the accurate analysis and understanding of the chemical composition of any gas mixture is of great importance for the efficient design of a tritium extraction and purification system or any tritium handling system. Methods like laser Raman spectroscopy and gas chromatography with thermal conductivity detector have been considered for hydrogen isotopes analyses in fuel cycles. Gas chromatography with a cryogenic separation column has been used for the analysis of hydrogen isotopes gas mixtures in general due to its high reliability and ease of operation. Hydrogen isotopes gas mixture analysis with cryogenic columns has been reported earlier using different column materials for percentage level composition. In the present work, trace levels of hydrogen isotopes (∼100 ppm of H 2 and D 2 ) have been analyzed with a Zeolite 5A and a modified γ-Al 2 O 3 column. Impurities in He gas (∼10 ppm of H 2 , O 2 , and N 2 ) have been analyzed using a Zeolite 13-X column. Gas chromatography with discharge ionization detection has been utilized for this purpose. The results of these experiments suggest that the columns developed were able to separate ppm levels of the desired components with a small response time (<6 min) and good resolution in both cases. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  18. STEADY STATE FLAMMABLE GAS RELEASE RATE CALCULATION & LOWER FLAMMABILITY LEVEL EVALUATION FOR HANFORD TANK WASTE

    Energy Technology Data Exchange (ETDEWEB)

    HU, T.A.

    2005-10-27

    Assess the steady-state flammability level at normal and off-normal ventilation conditions. The hydrogen generation rate was calculated for 177 tanks using the rate equation model. Flammability calculations based on hydrogen, ammonia, and methane were performed for 177 tanks for various scenarios.

  19. STEADY STATE FLAMMABLE GAS RELEASE RATE CALCULATION AND LOWER FLAMMABILITY LEVEL EVALUATION FOR HANFORD TANK WASTE

    Energy Technology Data Exchange (ETDEWEB)

    HU TA

    2009-10-26

    Assess the steady-state flammability level at normal and off-normal ventilation conditions. The hydrogen generation rate was calculated for 177 tanks using the rate equation model. Flammability calculations based on hydrogen, ammonia, and methane were performed for 177 tanks for various scenarios.

  20. Residual basins

    International Nuclear Information System (INIS)

    D'Elboux, C.V.; Paiva, I.B.

    1980-01-01

    Exploration for uranium carried out over a major portion of the Rio Grande do Sul Shield has revealed a number of small residual basins developed along glacially eroded channels of pre-Permian age. Mineralization of uranium occurs in two distinct sedimentary units. The lower unit consists of rhythmites overlain by a sequence of black shales, siltstones and coal seams, while the upper one is dominated by sandstones of probable fluvial origin. (Author) [pt

  1. Effects of graded levels of cupric citrate on growth performance, antioxidant status, serum lipid metabolites and immunity, and tissue residues of trace elements in weaned pigs

    Directory of Open Access Journals (Sweden)

    Chu Cai Peng

    2017-04-01

    Full Text Available Objective The goal of this study was to investigate the effects of cupric citrate (CuCit on growth performance, antioxidant indices, serum lipid metabolites, serum immune indices, and tissue residues of copper (Cu, zinc, and iron in weaned pigs. Methods A total of 180 weaned pigs (Duroc×Landrace×Large White with an average body weight of 8.98±1.21 kg were randomly assigned to a corn-soybean meal control ration, or 4 similar rations with 30, 60, 120, or 240 mg/kg Cu as CuCit. All diets contained 10 mg/kg Cu as cupric sulfate from the vitamin-mineral premix. The experiment was divided into two phases: 0 to 14 d (phase 1 and 15 to 28 d (phase 2. Results Average daily gain (ADG; linearly, p<0.01 and average daily feed intake (ADFI; linearly and quadratically, p<0.05 were affected by an increase in CuCit during phase 2. Overall period, ADG (p<0.05 and ADFI (p<0.01 were linearly increased with increasing dietary levels of CuCit. Serum malondialdehyde concentrations (p<0.05 and glutathione peroxidase activity (p<0.01 linearly decreased and increased respectively with an increase in CuCit. Serum levels of Cu-Zn superoxide dismutase were linearly affected with an increase in CuCit (p<0.01. Hepatic malondialdehyde levels decreased with an increase in CuCit (linearly and quadratically, p<0.01. Serum total cholesterol concentrations were quadratically affected (p<0.05 and decreased in pigs fed Cu as CuCit at 60 and 120 mg/kg and increased in pigs fed 240 mg/kg Cu as CuCit. Serum high-density lipoprotein concentrations were linearly affected with an increase in CuCit (p<0.01. Serum IL-1β levels were quadratically affected (p<0.05 by dietary treatment. Compared with other treatments, 240 mg/kg Cu from CuCit quadratically increased hepatic (p<0.01 and renal (p<0.05 Cu concentrations, and quadratically decreased hepatic and renal iron concentrations (p<0.05. Conclusion Cu administered in the form of CuCit at a dosage range of 30 to 60 mg/kg, effectively

  2. Residue analysis of organochlorine pesticides in water and ...

    African Journals Online (AJOL)

    Mr Willims

    2013-05-12

    May 12, 2013 ... residues were performed by injecting 1 µL of purified extract into the injection port of a gas chromatograph with a 63Ni electron capture .... Identification and determination of OCP residues by gas chromatography. A gas chromatograph with ..... Distribution of chlorine- ted pesticides in shellfishes from Lagos ...

  3. Boreal forests can have a remarkable role in reducing greenhouse gas emissions locally: Land use-related and anthropogenic greenhouse gas emissions and sinks at the municipal level

    International Nuclear Information System (INIS)

    Vanhala, Pekka; Bergström, Irina; Haaspuro, Tiina; Kortelainen, Pirkko; Holmberg, Maria; Forsius, Martin

    2016-01-01

    Ecosystem services have become an important concept in policy-making. Carbon (C) sequestration into ecosystems is a significant ecosystem service, whereas C losses can be considered as an ecosystem disservice. Municipalities are in a position to make decisions that affect local emissions and therefore are important when considering greenhouse gas (GHG) mitigation. Integrated estimations of fluxes at a regional level help local authorities to develop land use policies for minimising GHG emissions and maximising C sinks. In this study, the Finnish national GHG accounting system is modified and applied at the municipal level by combining emissions and sinks from agricultural land, forest areas, water bodies and mires (land use-related GHG emissions) with emissions from activities such as energy production and traffic (anthropogenic GHG emissions) into the LUONNIKAS calculation tool. The study area consists of 14 municipalities within the Vanajavesi catchment area located in Southern Finland. In these municipalities, croplands, peat extraction sites, water bodies and undrained mires are emission sources, whereas forests are large carbon sinks that turn the land use-related GHG budget negative, resulting in C sequestration into the ecosystem. The annual land use-related sink in the study area was 78 t CO 2 eq km −2 and 2.8 t CO 2 eq per capita. Annual anthropogenic GHG emissions from the area amounted to 250 t CO 2 eq km −2 and 9.2 t CO 2 eq per capita. Since forests are a significant carbon sink and the efficiency of this sink is heavily affected by forest management practices, forest management policy is a key contributing factor for mitigating municipal GHG emissions. - Highlights: • The significance of natural landscapes in the regional C budgets is shown. • Boreal forests can be remarkable C sinks enabling net C sequestration in ecosystems. • The large area of forest may compensate for all C emissions in the municipality. • Forest management policy can

  4. A variational approach to multi-phase motion of gas, liquid and solid based on the level set method

    Science.gov (United States)

    Yokoi, Kensuke

    2009-07-01

    We propose a simple and robust numerical algorithm to deal with multi-phase motion of gas, liquid and solid based on the level set method [S. Osher, J.A. Sethian, Front propagating with curvature-dependent speed: Algorithms based on Hamilton-Jacobi formulation, J. Comput. Phys. 79 (1988) 12; M. Sussman, P. Smereka, S. Osher, A level set approach for capturing solution to incompressible two-phase flow, J. Comput. Phys. 114 (1994) 146; J.A. Sethian, Level Set Methods and Fast Marching Methods, Cambridge University Press, 1999; S. Osher, R. Fedkiw, Level Set Methods and Dynamics Implicit Surface, Applied Mathematical Sciences, vol. 153, Springer, 2003]. In Eulerian framework, to simulate interaction between a moving solid object and an interfacial flow, we need to define at least two functions (level set functions) to distinguish three materials. In such simulations, in general two functions overlap and/or disagree due to numerical errors such as numerical diffusion. In this paper, we resolved the problem using the idea of the active contour model [M. Kass, A. Witkin, D. Terzopoulos, Snakes: active contour models, International Journal of Computer Vision 1 (1988) 321; V. Caselles, R. Kimmel, G. Sapiro, Geodesic active contours, International Journal of Computer Vision 22 (1997) 61; G. Sapiro, Geometric Partial Differential Equations and Image Analysis, Cambridge University Press, 2001; R. Kimmel, Numerical Geometry of Images: Theory, Algorithms, and Applications, Springer-Verlag, 2003] introduced in the field of image processing.

  5. Using Market Forces to Reduce Greenhouse Gas Emissions Through Product-Level Life Cycle Analysis and Eco-Labeling

    Science.gov (United States)

    Sweeney, J. F.; Davis, S. J.

    2007-12-01

    Established protocols allow entity-level accounting of greenhouse gas (GHG) emissions. The information contained within GHG inventories is used by entities to manage their carbon footprint and to anticipate future exposure to compulsory GHG markets or taxes. The efficacy of such inventories, as experienced by the consumer, can be improved upon by product-level GHG inventories applying the methods of traditional life cycle analysis (LCA). A voluntary product-level assessment of this type, coupled with an eco-label, would 1) empower consumers with information about the total embodied GHG content of a product, 2) allow companies to understand and manage GHG emissions outside the narrow scope of their entities, and 3) drive reduction of GHG emissions throughout product value chains. The Climate Conservancy (TCC) is a non-profit organization founded to help companies calculate their GHG emissions at the level of individual product units, and to inform consumers about the GHG intensity of the products they choose to purchase. With the assistance of economists, policy experts and scientists, TCC has developed a useful metric for reporting product-level GHG emissions that allows for a normalized comparison of a product's GHG intensity irrespective of industry sector or competitors, where GHG data are often unavailable or incomplete. Using this metric, we envision our Climate Conscious label becoming an important arbiter of choice for consumers seeking ways to mitigate their climate impacts without the need for governmental regulation.

  6. Combustion noise from gas turbine aircraft engines measurement of far-field levels

    Science.gov (United States)

    Krejsa, Eugene A.

    1987-01-01

    Combustion noise can be a significant contributor to total aircraft noise. Measurement of combustion noise is made difficult by the fact that both jet noise and combustion noise exhibit broadband spectra and peak in the same frequency range. Since in-flight reduction of jet noise is greater than that of combustion noise, the latter can be a major contributor to the in-flight noise of an aircraft but will be less evident, and more difficult to measure, under static conditions. Several methods for measuring the far-field combustion noise of aircraft engines are discussed in this paper. These methods make it possible to measure combustion noise levels even in situations where other noise sources, such as jet noise, dominate. Measured far-field combustion noise levels for several turbofan engines are presented. These levels were obtained using a method referred to as three-signal coherence, requiring that fluctuating pressures be measured at two locations within the engine core in addition to the far-field noise measurement. Cross-spectra are used to separate the far-field combustion noise from far-field noise due to other sources. Spectra and directivities are presented. Comparisons with existing combustion noise predictions are made.

  7. Assessing fuel spill risks in polar waters: Temporal dynamics and behaviour of hydrocarbons from Antarctic diesel, marine gas oil and residual fuel oil.

    Science.gov (United States)

    Brown, Kathryn E; King, Catherine K; Kotzakoulakis, Konstantinos; George, Simon C; Harrison, Peter L

    2016-09-15

    As part of risk assessment of fuel oil spills in Antarctic and subantarctic waters, this study describes partitioning of hydrocarbons from three fuels (Special Antarctic Blend diesel, SAB; marine gas oil, MGO; and intermediate grade fuel oil, IFO 180) into seawater at 0 and 5°C and subsequent depletion over 7days. Initial total hydrocarbon content (THC) of water accommodated fraction (WAF) in seawater was highest for SAB. Rates of THC loss and proportions in equivalent carbon number fractions differed between fuels and over time. THC was most persistent in IFO 180 WAFs and most rapidly depleted in MGO WAF, with depletion for SAB WAF strongly affected by temperature. Concentration and composition remained proportionate in dilution series over time. This study significantly enhances our understanding of fuel behaviour in Antarctic and subantarctic waters, enabling improved predictions for estimates of sensitivities of marine organisms to toxic contaminants from fuels in the region. Copyright © 2016 Elsevier Ltd. All rights reserved.

  8. A Multi-Factor Analysis of Sustainable Agricultural Residue Removal Potential

    Energy Technology Data Exchange (ETDEWEB)

    Jared Abodeely; David Muth; Paul Adler; Eleanor Campbell; Kenneth Mark Bryden

    2012-10-01

    Agricultural residues have significant potential as a near term source of cellulosic biomass for bioenergy production, but sustainable removal of agricultural residues requires consideration of the critical roles that residues play in the agronomic system. Previous work has developed an integrated model to evaluate sustainable agricultural residue removal potential considering soil erosion, soil organic carbon, greenhouse gas emission, and long-term yield impacts of residue removal practices. The integrated model couples the environmental process models WEPS, RUSLE2, SCI, and DAYCENT. This study uses the integrated model to investigate the impact of interval removal practices in Boone County, Iowa, US. Residue removal of 4.5 Mg/ha was performed annually, bi-annually, and tri-annually and were compared to no residue removal. The study is performed at the soil type scale using a national soil survey database assuming a continuous corn rotation with reduced tillage. Results are aggregated across soil types to provide county level estimates of soil organic carbon changes and individual soil type soil organic matter content if interval residue removal were implemented. Results show interval residue removal is possible while improving soil organic matter. Implementation of interval removal practices provide greater increases in soil organic matter while still providing substantial residue for bioenergy production.

  9. Determination of residual 1,4-dioxane in surfactants and cleaning agents using headspace single-drop microextraction followed by gas chromatography-flame ionization detection.

    Science.gov (United States)

    Saraji, M; Shirvani, N

    2017-02-01

    Polyethoxylated surfactants are widely used in the formulation of different cleaning agents such as shampoo, dish washing and hand washing products and lotion formulation. During the production of polyethoxylated surfactants, 1,4-dioxane as a toxic and carcinogenic by-product is formed. A simple low-cost method based on headspace single-drop microextraction combined with gas chromatography-flame ionization detection was developed for the determination of 1,4-dioxane in surfactants and cleaning agents. In this method, 1,4-dioxane was extracted from 8.0 mL sample solution into a microdrop of an organic solvent, and then, it was injected to gas chromatography. The effects of such parameters as the solvent type, salt addition, microdrop volume, stirring rate, equilibrium time, extraction time and the temperature of sample solution on the extraction performance were studied and optimized. An ethoxylated surfactant containing 1,4-dioxane was used as the sample for the optimization of the extraction parameters. The linear range, determination coefficient, limit of detection and relative standard deviation of the method were 0.5-100 μg g -1 , 0.9977, 0.4 μg g -1 and 7.2% (n = 5), respectively. Different real samples including sodium lauryl ether sulphate, sodium lauryl sulphate (SLS), four brands of shampoo, and hand washing and dish washing liquids were analysed by the method. 1,4-Dioxane was detected at the concentration range of 2.4-201 μg g -1 in the samples, except dish washing liquid and SLS. A new method with the merits of simplicity, low cost, low organic solvent consumption, short analysis time, good repeatability and suitable detection limit was developed for the analysis of 1,4-dioxane in surfactants and cleaning agents. © 2016 Society of Cosmetic Scientists and the Société Française de Cosmétologie.

  10. Leaf-level gas-exchange uniformity and photosynthetic capacity among loblolly pine (Pinus taeda L.) genotypes of contrasting inherent genetic variation

    Science.gov (United States)

    Michael J. Aspinwall; John S. King; Steven E. McKeand; Jean-Christophe Domec

    2011-01-01

    Variation in leaf-level gas exchange among widely planted genetically improved loblolly pine (Pinus taeda L.) genotypes could impact stand-level water use, carbon assimilation, biomass production, C allocation, ecosystem sustainability and biogeochemical cycling under changing environmental conditions. We examined uniformity in leaf-level light-saturated photosynthesis...

  11. Unintended greenhouse gas consequences of lowering level of service in urban transit systems

    International Nuclear Information System (INIS)

    Griswold, Julia B; Cheng, Han; Madanat, Samer; Horvath, Arpad

    2014-01-01

    Public transit is often touted as a ‘green’ transportation option and a way for users to reduce their environmental footprint by avoiding automobile emissions, but that may not be the case when systems run well below passenger capacity. In previous work, we explored an approach to optimizing the design and operations of transit systems for both costs and emissions, using continuum approximation models and assuming fixed demand. In this letter, we expand upon our previous work to explore how the level of service for users impacts emissions. We incorporate travel time elasticities into the optimization to account for demand shifts from transit to cars, resulting from increases in transit travel time. We find that emissions reductions are moderated, but not eliminated, for relatively inelastic users. We consider two scenarios: the first is where only the agency faces an emissions budget; the second is where the entire city faces an emissions budget. In the latter scenario, the emissions reductions resulting from reductions in transit level of service are mitigated as users switch to automobile. (letter)

  12. An Artificial Neural Network Compensated Output Feedback Power-Level Control for Modular High Temperature Gas-Cooled Reactors

    Directory of Open Access Journals (Sweden)

    Zhe Dong

    2014-02-01

    Full Text Available Small modular reactors (SMRs could be beneficial in providing electricity power safely and also be viable for applications such as seawater desalination and heat production. Due to its inherent safety features, the modular high temperature gas-cooled reactor (MHTGR has been seen as one of the best candidates for building SMR-based nuclear power plants. Since the MHTGR dynamics display high nonlinearity and parameter uncertainty, it is necessary to develop a nonlinear adaptive power-level control law which is not only beneficial to the safe, stable, efficient and autonomous operation of the MHTGR, but also easy to implement practically. In this paper, based on the concept of shifted-ectropy and the physically-based control design approach, it is proved theoretically that the simple proportional-differential (PD output-feedback power-level control can provide asymptotic closed-loop stability. Then, based on the strong approximation capability of the multi-layer perceptron (MLP artificial neural network (ANN, a compensator is established to suppress the negative influence caused by system parameter uncertainty. It is also proved that the MLP-compensated PD power-level control law constituted by an experientially-tuned PD regulator and this MLP-based compensator can guarantee bounded closed-loop stability. Numerical simulation results not only verify the theoretical results, but also illustrate the high performance of this MLP-compensated PD power-level controller in suppressing the oscillation of process variables caused by system parameter uncertainty.

  13. Output Feedback Dissipation Control for the Power-Level of Modular High-Temperature Gas-Cooled Reactors

    Directory of Open Access Journals (Sweden)

    Zhe Dong

    2011-11-01

    Full Text Available Because of its strong inherent safety features and the high outlet temperature, the modular high temperature gas-cooled nuclear reactor (MHTGR is the chosen technology for a new generation of nuclear power plants. Such power plants are being considered for industrial applications with a wide range of power levels, thus power-level regulation is very important for their efficient and stable operation. Exploiting the large scale asymptotic closed-loop stability provided by nonlinear controllers, a nonlinear power-level regulator is presented in this paper that is based upon both the techniques of feedback dissipation and well-established backstepping. The virtue of this control strategy, i.e., the ability of globally asymptotic stabilization, is that it takes advantage of the inherent zero-state detectability property of the MHTGR dynamics. Moreover, this newly built power-level regulator is also robust towards modeling uncertainty in the control rod dynamics. If modeling uncertainty of the control rod dynamics is small enough to be omitted, then this control law can be simplified to a classical proportional feedback controller. The comparison of the control performance between the newly-built power controller and the simplified controller is also given through numerical study and theoretical analysis.

  14. Incorporating regional growth into forecasts of greenhouse gas emissions from project-level residential and commercial development

    International Nuclear Information System (INIS)

    Rowangould, Dana; Eldridge, Melody; Niemeier, Deb

    2013-01-01

    To better understand the greenhouse gas (GHG) implications of land use planning decisions, regional planning organizations have developed tools to forecast the emissions from project-level residential and commercial development. This paper reviews the state of GHG emissions forecasting methods for project-level development. We argue that when forecasting changes in regional emissions it is important to make explicit what is assumed about a project′s effect on the population of residents and businesses in the region. We present five regional growth assumptions capturing the range of ways that project-level development might influence (i) construction and occupancy of similar developments elsewhere in a region and (ii) relocation of the initial activities that occur on-site before the project is built. We show that current forecasting tools inconsistently address the latter when they are interpreted as forecasted changes in regional emissions. Using a case study in Yolo County, California we demonstrate that forecasted changes in regional emissions are greatly affected by the regional growth assumption. In the absence of information about which regional growth assumption is accurate, we provide guidelines for selection of a conservative regional growth assumption. - Highlights: • Current tools inconsistently forecast GHG emissions from project-level development. • We outline five assumptions about how projects may affect regional growth. • Our assumptions capture a range of economic and population effects of projects. • Our case study shows that growth assumptions greatly affect regional GHG estimates. • We provide guidelines for selecting a conservative regional growth assumption

  15. Overview of Hanford Site High-Level Waste Tank Gas and Vapor Dynamics

    Energy Technology Data Exchange (ETDEWEB)

    Huckaby, James L.; Mahoney, Lenna A.; Droppo, James G.; Meacham, Joseph E.

    2004-08-31

    Hanford Site processes associated with the chemical separation of plutonium from uranium and other fission products produced a variety of volatile, semivolatile, and nonvolatile organic and inorganic waste chemicals that were sent to high-level waste tanks. These chemicals have undergone and continue to undergo radiolytic and thermal reactions in the tanks to produce a wide variety of degradation reaction products. The origins of the organic wastes, the chemical reactions they undergo, and their reaction products have recently been examined by Stock (2004). Stock gives particular attention to explaining the presence of various types of volatile and semivolatile organic species identified in headspace air samples. This report complements the Stock report by examining the storage of volatile and semivolatile species in the waste, their transport through any overburden of waste to the tank headspaces, the physical phenomena affecting their concentrations in the headspaces, and their eventual release into the atmosphere above the tanks.

  16. Carbon Monoxide, Nitric Oxide, and Nitrogen Dioxide Levels in Gas Ovens Related to Surface Pinking of Cooked Beef and Turkey.

    Science.gov (United States)

    Cornforth; Rabovitser; Ahuja; Wagner; Hanson; Cummings; Chudnovsky

    1998-01-19

    Carbon monoxide (CO) and total nitrogen oxide (NO(x)()) levels were monitored during meat cookery with a standard Ovenpak and a new ultralow-NO(x)() (ULN) cyclonic gas burner. With the standard burner, CO varied from 103 to 152 ppm, NO(x)() was 1.3-10.7 ppm, and surface pinking was observed on both beef and turkey. The ULN burner at optimal efficiency produced only 6.7 ppm of CO and 1 ppm of NO(x)(), insufficient to cause surface pinking. To determine the relative contribution of CO and NO(x)() to pinking, trials were also conducted in an electric oven with various pure gases. Pinking was not observed with up to 149 ppm of CO or 5 ppm of NO. However, as little as 0.4 ppm of nitrogen dioxide (NO(2)) caused pinking of turkey rolls. Beef roasts were pink at >2.5 ppm of NO(2). Thus, pinking previously attributed to CO and NO in gas ovens is instead due to NO(2), which has much greater reactivity than NO with moisture at meat surfaces.

  17. Estimating Greenhouse Gas Emissions Level of A Natural Gas Pipeline – Case Study from A to B Point in West Java-Indonesia

    OpenAIRE

    Dianita Cindy; Saputra Asep Handaya

    2016-01-01

    Indonesia is one of the highest greenhouse emitters in the world. As a response of this problem, Indonesia declared the national action plan to focus on national greenhouse gas (GHG) reduction by 26 % by 2020. To achieve this target, Government puts energy sector as one of the top priorities since it is the second strongest contributor to national GHG emissions. The main purpose of this paper is to apply the method of fugitive emissions calculation to the existing natural gas pipeline in Indo...

  18. Determination of triazole pesticide residues in edible oils using air-assisted liquid-liquid microextraction followed by gas chromatography with flame ionization detection.

    Science.gov (United States)

    Farajzadeh, Mir Ali; Feriduni, Behruz; Mogaddam, Mohammad Reza Afshar

    2015-03-01

    In the present study, a rapid, simple, and highly efficient sample preparation method based on air-assisted liquid-liquid microextraction followed by gas chromatography with flame ionization detection was developed for the extraction, preconcentration, and determination of five triazole pesticides (penconazole, hexaconazole, diniconazole, tebuconazole, and triticonazole) in edible oils. Initially, the oil samples were diluted with hexane and a few microliter of a less soluble organic solvent (extraction solvent) in hexane was added. To form fine and dispersed extraction solvent droplets, the mixture of oil sample solution and extraction solvent is repeatedly aspirated and dispersed with a syringe. Under the optimum extraction conditions, the method showed low limits of detection and quantification between 2.2-6.1 and 7.3-20 μg/L, respectively. Enrichment factors and extraction recoveries were in the ranges of 71-96 and 71-96%, respectively. The relative standard deviations for the extraction of 100 and 250 μg/L of each pesticide were less than 5% for intraday (n = 6) and interday (n = 3) precisions. Finally edible oil samples were successfully analyzed using the proposed method, and hexaconazole was found in grape seed oil. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  19. An inexact two-stage stochastic energy systems planning model for managing greenhouse gas emission at a municipal level

    International Nuclear Information System (INIS)

    Energy management systems are highly complicated with greenhouse-gas emission reduction issues and a variety of social, economic, political, environmental and technical factors. To address such complexities, municipal energy systems planning models are desired as they can take account of these factors and their interactions within municipal energy management systems. This research is to develop an interval-parameter two-stage stochastic municipal energy systems planning model (ITS-MEM) for supporting decisions of energy systems planning and GHG (greenhouse gases) emission management at a municipal level. ITS-MEM is then applied to a case study. The results indicated that the developed model was capable of supporting municipal energy systems planning and environmental management under uncertainty. Solutions of ITS-MEM would provide an effective linkage between the pre-regulated environmental policies (GHG-emission reduction targets) and the associated economic implications (GHG-emission credit trading).

  20. Integrated solar combined cycles using gas turbines with partial recuperation and solar integration at different pressure levels

    Science.gov (United States)

    Rovira, Antonio; Sánchez, Consuelo; Fernández, Santiago; Muñoz, Marta; Barbero, Rubén

    2017-06-01

    This work studies and compares two alternatives to improve the solar-to-electricity energy conversion efficiency in integrated solar combined cycle power plants (ISCC), which are based on the use of combined cycles including partial recuperative gas turbines. Each alternative has been integrated into dual and triple pressure levels with reheat heat recovery steam generators (HRSG). Partial recuperation conveys lower heat recovery at the steam generator than in conventional plants, because each MW exchanged in the recuperator is not available at the HRSG. This thermal power decrease at the HRSG may be overcome by the integration of solar energy that is implemented using parabolic trough collectors. Moreover, with such an implementation each solar thermal MW integrated allows a MW of heat recuperation and, thus a MW of fossil fuel saving, thus the solar heat-to-electricity energy conversion rate may reach values up to 50 %, which makes the proposal interesting.

  1. Greenhouse Gas (CH4, CO2 and N2O) Emission Levels by Wastewater Treatment Plant (WWTP) Ponds in Brazil

    Science.gov (United States)

    Rossete, A. L. M.; Sundefeld Junior, G.; Aparicio, C.; Baldi, G. G.; Montes, C. R.; Piveli, R. P.; Melfi, A. J.

    2015-12-01

    This study measured greenhouse gas emissions (GHG) by Facultative Ponds on Wastewater Treatment Plants. The most studied GHGs include CO2, CH4and N2O. The level of GHG (CO2, CH4 and N2O) emissions by WWTPs in Australian-type stabilization ponds was measured in the city of Lins (22º21'S, 49º50'W), state of São Paulo (SP), Brazil. GHG collection was carried outusing a collection chamber installed at the center of the facultative pond's final third. The effluent's pH and temperature (ET) were registered by probes, and meteorological information regarding air temperature (AT) and solar radiation (SR) were obtained from INMET, Brazil. GHG collection was carried out for 72 consecutive hours in June 2014, on an hourly basis, once every 5 minutes, for the first 30 minutes, and once every 10 minutes from 30 to 50 minutesand subsequently analyzed by gas chromatograph (GC).After three days of data collection, the average AT, SR, ET and pH values were, respectively, 18oC, 2583kJm-2, 23oC and 8.2. Average values for GHG emission levels (CH4, CO2 and N2O) were 79.01; 100.65 and 0.0 mg m-2 h-1, respectively. GHG emission levels were divided into light periods (morning, afternoon and evening)in order to verify the periods with the highest GHG emissions.The highest CH4 emission levels were measured between morning and early afternoon. The maximum CO2 emissions were observed from evening to early morning. N2O emissions were constant and values were close to the ones found in the atmosphere, which shows the emission of N2O by facultative ponds does not contribute to greenhouse gases emissions.The results enabled us to characterize and quantify GHG emission levels per Facultative Pond on Wastewater Treatment Plant. Acknowledgment to FAPESP and SABESP, Brazil.

  2. Boreal forests can have a remarkable role in reducing greenhouse gas emissions locally: Land use-related and anthropogenic greenhouse gas emissions and sinks at the municipal level

    Energy Technology Data Exchange (ETDEWEB)

    Vanhala, Pekka, E-mail: pekka.vanhala@ymparisto.fi [Finnish Environment Institute, Natural Environment Centre, P.O. Box 140, Mechelininkatu 34 a, FI-00251 Helsinki (Finland); Bergström, Irina [Finnish Environment Institute, Natural Environment Centre, P.O. Box 140, Mechelininkatu 34 a, FI-00251 Helsinki (Finland); Haaspuro, Tiina [University of Helsinki, Department of Environmental Sciences, P.O. Box 65, Viikinkaari 1, 00014 Helsinki (Finland); Kortelainen, Pirkko; Holmberg, Maria; Forsius, Martin [Finnish Environment Institute, Natural Environment Centre, P.O. Box 140, Mechelininkatu 34 a, FI-00251 Helsinki (Finland)

    2016-07-01

    Ecosystem services have become an important concept in policy-making. Carbon (C) sequestration into ecosystems is a significant ecosystem service, whereas C losses can be considered as an ecosystem disservice. Municipalities are in a position to make decisions that affect local emissions and therefore are important when considering greenhouse gas (GHG) mitigation. Integrated estimations of fluxes at a regional level help local authorities to develop land use policies for minimising GHG emissions and maximising C sinks. In this study, the Finnish national GHG accounting system is modified and applied at the municipal level by combining emissions and sinks from agricultural land, forest areas, water bodies and mires (land use-related GHG emissions) with emissions from activities such as energy production and traffic (anthropogenic GHG emissions) into the LUONNIKAS calculation tool. The study area consists of 14 municipalities within the Vanajavesi catchment area located in Southern Finland. In these municipalities, croplands, peat extraction sites, water bodies and undrained mires are emission sources, whereas forests are large carbon sinks that turn the land use-related GHG budget negative, resulting in C sequestration into the ecosystem. The annual land use-related sink in the study area was 78 t CO{sub 2} eq km{sup −2} and 2.8 t CO{sub 2} eq per capita. Annual anthropogenic GHG emissions from the area amounted to 250 t CO{sub 2} eq km{sup −2} and 9.2 t CO{sub 2} eq per capita. Since forests are a significant carbon sink and the efficiency of this sink is heavily affected by forest management practices, forest management policy is a key contributing factor for mitigating municipal GHG emissions. - Highlights: • The significance of natural landscapes in the regional C budgets is shown. • Boreal forests can be remarkable C sinks enabling net C sequestration in ecosystems. • The large area of forest may compensate for all C emissions in the municipality.

  3. Variations of the blood gas levels and thermodilutional parameters during ICP monitoring after severe head trauma in children.

    Science.gov (United States)

    Lubrano, Riccardo; Elli, Marco; Stoppa, Francesca; Di Traglia, Mario; Di Nardo, Matteo; Perrotta, Daniela; David, Piero; Paoli, Sara; Cecchetti, Corrado

    2015-08-01

    The purpose of this study was to define, in children following head trauma and GSC ≤ 8, at which level of intracranial pressure (ICP), the thermodilutional, and gas analytic parameters implicated in secondary cerebral insults shows initial changes. We enrolled in the study 56 patients: 30 males and 26 females, mean age 71 ± 52 months. In all children, volumetric hemodynamic and blood gas parameters were monitored following initial resuscitation and every 4 h thereafter or whenever a hemodynamic deterioration was suspected. During the cumulative hospital stay, a total of 1050 sets of measurements were done. All parameters were stratified in seven groups according to ICP (group A1 = 0-5 mmHg, group A2 = 6-10 mmHg, group A3 = 11-15 mmHg, group A4 16-20 mmHg, group A5 21-25 mmHg, group A6 26-30 mmHg, group A7 >31 mmHg). Mean values of jugular oxygen saturation (SJO2), jugular oxygen partial pressure (PJO2), extravascular lung water (EVLWi), pulmonary vascular permeability (PVPi), fluid overload (FO), and cerebral extraction of oxygen (CEO2) vary significantly from A3 (11-15 mmHg) to A4 (16-20 mmHg). They relate to ICP in a four-parameter sigmoidal function (4PS function with: r(2) = 0.90), inflection point of 15 mmHg of ICP, and a maximum curvature point on the left horizontal asymptote at 13 mmHg of ICP. Mean values of SJO2, PJO2, EVLWi, PVPi, FO, and CEO2 become pathologic at 15 mmHg of ICP; however, the curve turns steeper at 13 mmHg, possibly a warning level in children for the development of post head trauma secondary insult.

  4. Effect of Machine Smoking Intensity and Filter Ventilation Level on Gas-Phase Temperature Distribution Inside a Burning Cigarette

    Directory of Open Access Journals (Sweden)

    Li Bin

    2015-01-01

    Full Text Available Accurate measurements of cigarette coal temperature are essential to understand the thermophysical and thermo-chemical processes in a burning cigarette. The last system-atic studies of cigarette burning temperature measurements were conducted in the mid-1970s. Contemporary cigarettes have evolved in design features and multiple standard machine-smoking regimes have also become available, hence there is a need to re-examine cigarette combustion. In this work, we performed systematic measurements on gas-phase temperature of burning cigarettes using an improved fine thermocouple technique. The effects of machine-smoking parameters (puff volume and puff duration and filter ventilation levels were studied with high spatial and time resolutions during single puffs. The experimental results were presented in a number of differ-ent ways to highlight the dynamic and complex thermal processes inside a burning coal. A mathematical distribution equation was used to fit the experimental temperature data. Extracting and plotting the distribution parameters against puffing time revealed complex temperature profiles under different coal volume as a function of puffing intensities or filter ventilation levels. By dividing the coal volume prior to puffing into three temperature ranges (low-temperature from 200 to 400 °C, medium-temperature from 400 to 600 °C, and high-temperature volume above 600 °C by following their development at different smoking regimes, useful mechanistic details were obtained. Finally, direct visualisation of the gas-phase temperature through detailed temperature and temperature gradient contour maps provided further insights into the complex thermo-physics of the burning coal. [Beitr. Tabakforsch. Int. 26 (2014 191-203

  5. Entrepreneurial orientation and corporate governance structures at the firm level in the South African oil and gas industry

    Directory of Open Access Journals (Sweden)

    Vincent B. Molokwu

    2013-03-01

    Full Text Available Orientation: Corporate governance systems (CGS have been observed as one of the most important structures and mechanisms that regulate the relationships between executives and shareholders. By having well-defined and established CGS, company board members and executives are able to shape company vision and increase managerial commitment towards formulating strategies that espouse an entrepreneurial orientation (EO. Firms with high levels of EO tend to be innovative and encourage creative initiatives in new products and technology developments.Research purpose: In an emerging economy such as South Africa, one of the primary goals of an organisation is growth and good governance, which can be achieved through wellgoverned structures and continuous innovation in the face of challenges. This study identified potential links between the multidimensional constructs of CGS and EO at the firm level in the South African oil and gas industry.Motivation for the study: One of the greatest challenges faced by organisations when implementing CGS is to ensure compliance.Research design, approach and method: Board members and senior decision-makers were surveyed in the South African oil and gas industry, using a structured questionnaire. A series of correlational analyses were used to determine the strength of relationships between the dimensions of EO and CGS.Main findings: By drawing extensively on existing theory on EO, this study found that the different dimensions of CGS have a significant and positive relationship with each of the EO dimensions – innovation, risk-taking and proactiveness.Practical/managerial implications: Corporate boards supportive of entrepreneurship must provide appropriate reward systems, top management support, explicit goals and appropriate organisational values which signal to employees that entrepreneurial behaviour action is desirable. Practitioners should scrutinise their governance structures in their organisations to ensure

  6. Entrepreneurial orientation and corporate governance structures at the firm level in the South African oil and gas industry

    Directory of Open Access Journals (Sweden)

    Vincent B. Molokwu

    2013-03-01

    Full Text Available Orientation: Corporate governance systems (CGS have been observed as one of the most important structures and mechanisms that regulate the relationships between executives and shareholders. By having well-defined and established CGS, company board members and executives are able to shape company vision and increase managerial commitment towards formulating strategies that espouse an entrepreneurial orientation (EO. Firms with high levels of EO tend to be innovative and encourage creative initiatives in new products and technology developments. Research purpose: In an emerging economy such as South Africa, one of the primary goals of an organisation is growth and good governance, which can be achieved through wellgoverned structures and continuous innovation in the face of challenges. This study identified potential links between the multidimensional constructs of CGS and EO at the firm level in the South African oil and gas industry. Motivation for the study: One of the greatest challenges faced by organisations when implementing CGS is to ensure compliance. Research design, approach and method: Board members and senior decision-makers were surveyed in the South African oil and gas industry, using a structured questionnaire. A series of correlational analyses were used to determine the strength of relationships between the dimensions of EO and CGS. Main findings: By drawing extensively on existing theory on EO, this study found that the different dimensions of CGS have a significant and positive relationship with each of the EO dimensions – innovation, risk-taking and proactiveness. Practical/managerial implications: Corporate boards supportive of entrepreneurship must provide appropriate reward systems, top management support, explicit goals and appropriate organisational values which signal to employees that entrepreneurial behaviour action is desirable. Practitioners should scrutinise their governance structures in their organisations to

  7. RESIDUAL RISK ASSESSMENTS - RESIDUAL RISK ...

    Science.gov (United States)

    This source category previously subjected to a technology-based standard will be examined to determine if health or ecological risks are significant enough to warrant further regulation for Coke Ovens. These assesments utilize existing models and data bases to examine the multi-media and multi-pollutant impacts of air toxics emissions on human health and the environment. Details on the assessment process and methodologies can be found in EPA's Residual Risk Report to Congress issued in March of 1999 (see web site). To assess the health risks imposed by air toxics emissions from Coke Ovens to determine if control technology standards previously established are adequately protecting public health.

  8. Electrodialytic remediation of air pollution control residues

    DEFF Research Database (Denmark)

    Jensen, Pernille Erland

    Air pollution control (APC) residue from municipal solid waste incineration (MSWI) consists of the fly ash, and, in dry and semi-dry systems, also the reaction products from the flue gas cleaning process. APC residue is considered a hazardous waste due to its high alkalinity, high content of salts...

  9. Improvement and extension to new analytes of a multi-residue method for the determination of pesticides in cereals and dry animal feed using gas chromatography-tandem quadrupole mass spectrometry revisited.

    Science.gov (United States)

    Walorczyk, Stanisław; Drożdżyński, Dariusz

    2012-08-17

    This article describes a substantially improved multi-residue method for the determination of a large number of pesticides in cereal samples (wheat, rye, barley, oats, maze, buckwheat etc.) and various animal feeds. The sample preparation method and the GC-MS/MS acquisition method were modified to accommodate new complex cereal and feed matrices and to extend the existing analytical scope to 167 pesticides. The co-extractives were reduced by the joint use of primary secondary amine (PSA) and octadecyl (C18), 75 mg and 50 mg/1 mL of acetonitrile extract, in the presence of MgSO(4), and thus the optimal recovery and analytical selectivity were obtained simultaneously. The new cleanup procedure was faster and easier to handle than our previously applied cleanup procedure. The overall recoveries of the pesticides from buckwheat and rye at the three spiking levels of 0.01, 0.05 and 0.25 mg kg(-1) were 96 ± 9% with relative standard deviations of 10 ± 4% on average. At the lowest spiking level of 0.01 mg kg(-1), 137 of 167 pesticide residues (82%) fulfilled the validation criteria with recoveries in the range of 70-120% and RSDs less or equal 20% whereas in the previous approach it was 93 out of 140 analytes (66%). The developed method was implemented in a routine analysis of approximately 900 real samples, providing an increased scope of the analysis, improved analytical performance parameters and improved ruggedness versus the previous approach. A total of 17% analyzed samples contained pesticide residues. There were 24 different compounds encountered in the samples, of which pirimiphos-methyl, tebuconazole, deltamethrin, and chlorpyrifos-methyl were the most frequent ones. Copyright © 2012 Elsevier B.V. All rights reserved.

  10. Development of a multi-residue method for the determination of pesticides in cereals and dry animal feed using gas chromatography-tandem quadrupole mass spectrometry II. Improvement and extension to new analytes.

    Science.gov (United States)

    Walorczyk, Stanisław

    2008-10-24

    This paper describes the extension and re-validation of a previously published multi-residue method to currently 140 pesticides and 4 pesticide degradation products in cereals and feedingstuffs. The pesticides were extracted using buffered QuEChERS ("quick, easy, cheap, rugged, effective and safe") method and then cleaned up using dispersive solid-phase extraction with Bondesil PSA and C18 sorbents, and optionally by a freezing-out clean-up step. The final extracts were analyzed in a single injection gas chromatographic-tandem quadrupole mass spectrometric (GC-MS/MS) acquisition method. A high degree of confidence was achieved by entering two multiple reaction monitoring transitions per compound. In this way, quantification of analytical results and unequivocal identification of pesticide residues in compliance with the recent European Union criteria could be done in a single analysis. Thorough optimization of the GC-MS/MS acquisition conditions and application of an effective clean-up procedure has resulted in a remarkable enhancement of the validation parameters. The linearity of the calibration curves was excellent in matrix-matched standards, and yielded the coefficients of determination (R(2))> or =0.99 for approximately 96% of the target analytes. Average recoveries of the pesticides spiked at 0.01mgkg(-1) into a feed mixture and wheat grain were in the range 70-120% with associated RSD values feed mixtures and other samples such as malt, starch and dry vegetables have been analyzed. A total of 15 different pesticides have been detected, among which pirimiphos methyl (19 cases), deltamethrin (14 cases), tolylfluanid (5 cases), dichlofluanid (5 cases), and tebuconazole (4 cases) were the most frequently encountered ones.

  11. Sensing Parts per Million Level Ammonia and Parts per Billion Level Acetic Acid in the Gas Phase by Common Black Film with a Fluorescent pH Probe.

    Science.gov (United States)

    Fu, Jingni; Zhang, Luning

    2018-01-16

    Relying on the nanometer-thick water core and large surface area-to-volume ratio (∼2 × 10 8 m -1 ) of common black film (CBF), we are able to use a pH-sensitive dye (carboxy-seminaphthorhodafluor-1, SNARF-1) to detect ammonia and acetic acid gas adsorption into the CBF, with the limit of detection reaching 0.8 ppm for NH 3 gas and 3 ppb for CH 3 COOH gas in the air. Data analysis reveals that fluorescence signal change is linearly proportional to the gas concentration up to 15 ppm and 65 ppb for NH 3 and CH 3 COOH, respectively.

  12. Distribution, Identification, and Quantification of Residues after Treatment of Ready-To-Eat Salami with36Cl-Labeled or Nonlabeled Chlorine Dioxide Gas.

    Science.gov (United States)

    Smith, David J; Giddings, J Michael; Herges, Grant R; Ernst, William

    2016-11-09

    When ready-to-eat salami was treated in a closed system with 36 Cl-labeled ClO 2 (5.5 mg/100 g of salami), essentially all radioactivity was deposited onto the salami. Administered 36 ClO 2 was converted to 36 Cl-chloride ion (>97%), trace levels of chlorate (chlorine dioxide treated (128 ± 31.2 ng/g) salami. If sanitation occurred under conditions of illumination, detectable levels (3.7 ± 1.5 ng/g) of perchlorate were formed along with greater quantities of sodium chlorate (183.6 ± 75.4 ng/g). Collectively, these data suggest that ClO 2 is chemically reduced by salami and that slow-release formulations might be appropriate for applications involving the sanitation of ready-to-eat meat products.

  13. Pesticide residue levels in strawberry processing by-products that are rich in ellagitannins and an assessment of their dietary risk to consumers

    Directory of Open Access Journals (Sweden)

    Michał Sójka

    2015-06-01

    Conclusion: Although the pesticide residue contents in strawberry by-products are higher than in fresh fruits, the suggested doses of the by-products are lower. Therefore, the dietary risk to consumers from strawberry by-products is comparable to that from fresh fruits.

  14. Rapid trace level determination of sulfonamide residues in honey with online extraction using short C-18 column by high-performance liquid chromatography with fluorescence detection.

    Science.gov (United States)

    Sajid, Muhammad; Na, Na; Safdar, Muhammad; Lu, Xin; Ma, Lin; He, Lan; Ouyang, Jin

    2013-11-01

    A sensitive and inexpensive quantification method with online extraction using a short C-18 column for sulfonamide residues in honey by high performance liquid chromatography with fluorescence detector was developed and validated. In sample preparation, acid hydrolysis was used to break the N-glycoside bond between the honey sugar and sulfonamide drugs and derivatization of sulfonamide residues with fluorescamine was conducted at pH 3.5 using a citrate buffer (0.5M) in the honey matrix. The chromatography was carried out on Zorbax Extended C-18 (250mm×4.6mm; 5μm) column, using a mixture of acetonitrile and an acetate buffer (pH 4.50, 20mM) as a mobile phase. A Zorbax Extended C-18 (12mm×4.6mm; 5μm) column was used for online extraction of fifteen sulfonamide residues from honey sample with the help of a two position valve. The limit of quantification of sulfonamide residues in honey was less than 3ngg(-1), and the percentage recovery of study compounds in spiked honey sample was from 80% for sulfacetamide to 100% of sulfachloropyridazine. The developed method has excellent linearity for all studied sulfonamides with a correlation coefficient 0.993. Copyright © 2013 Elsevier B.V. All rights reserved.

  15. Residual effect of injectable moxidectin against lungworm and gastrointestinal nematodes in calves exposed to high pasture infectivity levels in the Netherlands.

    NARCIS (Netherlands)

    Eysker, M.; Boersema, J.H.; Cornelissen, J.B.W.J.; Kloosterman, A.; Kooyman, F.N.J.

    1996-01-01

    The residual effect of a 0.2 mg kg−1 injectable formulation of moxidectin against lungworm and gastrointestinal nematodes in cattle was studied in a grazing experiment in the Netherlands. Five groups of four calves were grazed between May and October 1991 and one similar group was used as

  16. Residual replacement strategies for Krylov subspace iterative methods for the convergence of true residuals

    NARCIS (Netherlands)

    Vorst, H.A. van der; Ye, Q.

    1999-01-01

    In this paper, a strategy is proposed for alternative computations of the residual vectors in Krylov subspace methods, which improves the agreement of the computed residuals and the true residuals to the level of O(u)kAkkxk. Building on earlier ideas on residual replacement and on insights in

  17. Clean-up of cereal extracts for gas chromatography-tandem quadrupole mass spectrometry pesticide residues analysis using primary secondary amine and C18

    DEFF Research Database (Denmark)

    Herrmann, Susan Strange; Poulsen, Mette Erecius

    2015-01-01

    The level of co-extracted matrix in wheat and oat extracts obtained by the QuEChERS method (EN 15662) is high and the occurrence of free fatty acids generates a major matrix peak in TIC chromatograms (rt. 13-22min). Matrix can compromise the analytical performance in pesticide analysis using GC-MS/MS...... low intensity of the matrix peak. For oat the analytical responses of the target pesticides generally increased with increasing amount of PSA. C18 had no significant effect on the intensity of the major matrix peaks and even resulted in lower analytical responses for several of the target pesticides...

  18. Residual nilpotence and residual solubility of groups

    International Nuclear Information System (INIS)

    Mikhailov, R V

    2005-01-01

    The properties of the residual nilpotence and the residual solubility of groups are studied. The main objects under investigation are the class of residually nilpotent groups such that each central extension of these groups is also residually nilpotent and the class of residually soluble groups such that each Abelian extension of these groups is residually soluble. Various examples of groups not belonging to these classes are constructed by homological methods and methods of the theory of modules over group rings. Several applications of the theory under consideration are presented and problems concerning the residual nilpotence of one-relator groups are considered.

  19. Water level, vegetation composition, and plant productivity explain greenhouse gas fluxes in temperate cutover fens after inundation

    Science.gov (United States)

    Minke, Merten; Augustin, Jürgen; Burlo, Andrei; Yarmashuk, Tatsiana; Chuvashova, Hanna; Thiele, Annett; Freibauer, Annette; Tikhonov, Vitalij; Hoffmann, Mathias

    2016-07-01

    Peat extraction leaves a land surface with a strong relief of deep cutover areas and higher ridges. Rewetting inundates the deep parts, while less deeply extracted zones remain at or above the water level. In temperate fens the flooded areas are colonized by helophytes such as Eriophorum angustifolium, Carex spp., Typha latifolia or Phragmites australis dependent on water depth. Reeds of Typha and Phragmites are reported as large sources of methane, but data on net CO2 uptake are contradictory for Typha and rare for Phragmites. Here, we analyze the effect of vegetation, water level and nutrient conditions on greenhouse gas (GHG) emissions for representative vegetation types along water level gradients at two rewetted cutover fens (mesotrophic and eutrophic) in Belarus. Greenhouse gas emissions were measured campaign-wise with manual chambers every 2 to 4 weeks for 2 years and interpolated by modelling. All sites had negligible nitrous oxide exchange rates. Most sites were carbon sinks and small GHG sources. Methane emissions generally increased with net ecosystem CO2 uptake. Mesotrophic small sedge reeds with water table around the land surface were small GHG sources in the range of 2.3 to 4.2 t CO2 eq. ha-1 yr-1. Eutrophic tall sedge - Typha latifolia reeds on newly formed floating mats were substantial net GHG emitters in the range of 25.1 to 39.1 t CO2 eq. ha-1 yr. They represent transient vegetation stages. Phragmites reeds ranged between -1.7 to 4.2 t CO2 eq. ha-1 yr-1 with an overall mean GHG emission of 1.3 t CO2 eq. ha-1 yr-1. The annual CO2 balance was best explained by vegetation biomass, which includes the role of vegetation composition and species. Methane emissions were obviously driven by biological activity of vegetation and soil organisms. Shallow flooding of cutover temperate fens is a suitable measure to arrive at low GHG emissions. Phragmites australis establishment should be promoted in deeper flooded areas and will lead to moderate, but

  20. Detection of clenbuterol at trace levels in doping analysis using different gas chromatographic-mass spectrometric techniques.

    Science.gov (United States)

    Yang, Sheng; Liu, Xin; Xing, Yanyi; Zhang, Dapeng; Wang, Shan; Wang, Xiaobing; Xu, Youxuan; Wu, Moutian; He, Zhenwen; Zhao, Jian

    2013-01-01

    This study demonstrates the development of a gas chromatography-triple quadrupole tandem mass spectrometry (GC-MS-MS) assay to detect clenbuterol in human urine and the comparison of this method with GC-MS techniques and gas chromatography-high resolution mass spectrometry (GC-HRMS) techniques. Urine samples were hydrolyzed with β-glucuronidase, extracted with methyl tert-butyl ether and dried under nitrogen. The derivative reagent was N-methyl-N-(trimethylsilyl)-trifluoroacetamide with NH4I and was analyzed by GC-MS, GC-MS-MS and GC-HRMS. A validation study was conducted by GC-MS-MS. The analyses of clenbuterol using different mass spectrometric techniques were compared. The limit of detection (LOD) for clenbuterol in human urine was 2 ng/mL by GC-MS (selected ion monitoring mode: SIM mode), 0.06 ng/mL by GC-HRMS and 0.03 ng/mL by GC-MS-MS, respectively, while the LOD by GC-HRMS was 0.06. With GC-MS-MS, the intra-assay and inter-assay precisions were less than 15%, the recoveries were 86 to 112% and the linear range was 0.06 to 8.0 ng/mL. The GC-MS under SIM mode can be used as a screening tool to detect clenbuterol at trace levels in human urine. The GC-MS-MS and GC-HRMS methods can confirm clenbuterol when its concentration is below 2 ng/mL. The results demonstrate that the GC-MS-MS method is quite sensitive, specific and reliable for the detection of clenbuterol in doping analysis.

  1. Determination of physiological levels of volatile organic compounds in blood using static headspace capillary gas chromatography with serial triple detection.

    Science.gov (United States)

    Schroers, H J; Jermann, E; Begerow, J; Hajimiragha, H; Chiarotti-Omar, A M; Dunemann, L

    1998-04-01

    A static capillary gas chromatographic method using three different detectors [photoionization detector (PID), electron capture detector (ECD) and flame ionization detector (FID)] switched in series is presented for the determination of volatile organic compounds (VOCs) in sub microgram l-1 levels. The method was applied for the analysis of selected environmentally and occupationally relevant non-halogenated and chlorinated aromatic hydrocarbons (e.g., benzene, toluene, xylenes, dichlorobenzenes) as well as chlorinated aliphatic hydrocarbons (e.g., trichloroethene, tetrachloroethene) in blood samples. Detailed investigations, in respect to the figures of merit were carried out. For most of the selected VOCs detection limits (calculated as the three-fold standard deviation of low level calibration standards) in the range from 26 (benzene) to 67 ng l-1 (m/p-xylene) were achieved which are comparable with those reported for dynamic headspace techniques in combination with mass spectrometric detection. For the individual VOCs the within-series precision varied from 4 to 19% and the day-to-day precision from 11 to 28%. Regarding PID as well as FID the calibration graphs for all substances were linear up to at least 10 micrograms l-1 while the ECD response was linear up to concentrations of about 0.6 microgram l-1 for the halogenated compounds. Our method is applicable for the quantitative determination of VOCs in blood in the occupationally as well as in the physiologically relevant (normal) concentration range.

  2. Forest residues in cattle feed

    Directory of Open Access Journals (Sweden)

    João Elzeário Castelo Branco Iapichini

    2012-12-01

    amount of 1% over the live weight + 10% of intake. The results of the first phase of the research, for steers supplemented in pasture, showed good acceptability and consumption in the three levels of substitution, with an average of 3.0 kg of concentrate per head. No rejection was observed for consumption of the mixture, as well as any physiological negative / change and clinical levels tested The pine cone (strobilus without the pine nuts (seeds was obtained as a residue of genetically improved seed collection. Likely source of tannins and fiber, dried and triturated pine cones can contribute to lower production costs due to the substitution of an ingredient in feed formulation, as an aid in control of internal parasites and also in the possible mitigation of methane gas production, resulting from digestion of ruminants, one of the gases responsible for the greenhouse effect. The potential use of pine cone as an ingredient in replacement of roughage and concentrate in the diet of ruminants qualifies as a new source of revenue in pine forestry activity, since no such product currently has no commercial value timber and its accumulation along the dried leaves among the trees, increase the risk of forest fires. Finally, these technological and social innovations result in remarkable potential to leverage Regional Programs Sustainable Development.

  3. Reducing residual stresses and deformations in selective laser melting through multi-level multi-scale optimization of cellular scanning strategy

    DEFF Research Database (Denmark)

    Mohanty, Sankhya; Hattel, Jesper Henri

    2016-01-01

    Residual stresses and deformations continue to remain one of the primary challenges towards expanding the scope of selective laser melting as an industrial scale manufacturing process. While process monitoring and feedback-based process control of the process has shown significant potential......, there is still dearth of techniques to tackle the issue. Numerical modelling of selective laser melting process has thus been an active area of research in the last few years. However, large computational resource requirements have slowed the usage of these models for optimizing the process.In this paper......, a calibrated, fast, multiscale thermal model coupled with a 3D finite element mechanical model is used to simulate residual stress formation and deformations during selective laser melting. The resulting reduction in thermal model computation time allows evolutionary algorithm-based optimization of the process...

  4. Saturated Adaptive Output-Feedback Power-Level Control for Modular High Temperature Gas-Cooled Reactors

    Directory of Open Access Journals (Sweden)

    Zhe Dong

    2014-11-01

    Full Text Available Small modular reactors (SMRs are those nuclear fission reactors with electrical output powers of less than 300 MWe. Due to its inherent safety features, the modular high temperature gas-cooled reactor (MHTGR has been seen as one of the best candidates for building SMR-based nuclear plants with high safety-level and economical competitive power. Power-level control is crucial in providing grid-appropriation for all types of SMRs. Usually, there exists nonlinearity, parameter uncertainty and control input saturation in the SMR-based plant dynamics. Motivated by this, a novel saturated adaptive output-feedback power-level control of the MHTGR is proposed in this paper. This newly-built control law has the virtues of having relatively neat form, of being strong adaptive to parameter uncertainty and of being able to compensate control input saturation, which are given by constructing Lyapunov functions based upon the shifted-ectropies of neutron kinetics and reactor thermal-hydraulics, giving an online tuning algorithm for the controller parameters and proposing a control input saturation compensator respectively. It is proved theoretically that input-to-state stability (ISS can be guaranteed for the corresponding closed-loop system. In order to verify the theoretical results, this new control strategy is then applied to the large-range power maneuvering control for the MHTGR of the HTR-PM plant. Numerical simulation results show not only the relationship between regulating performance and control input saturation bound but also the feasibility of applying this saturated adaptive control law practically.

  5. Evaluation of ground level concentration of pollutant due to gas flaring by computer simulation: A case study of Niger - Delta area of Nigeria

    Directory of Open Access Journals (Sweden)

    A. S. ABDULKAREEM

    2005-01-01

    Full Text Available The disposal of associated gases through flaring has been a major problem for the Nigerian oil and gas industries and most of theses gases are flared due to the lack of commercial out lets. The resultant effects of gas flaring are the damaging effect of the environment due to acid rain formation, green house effect, global warming and ozone depletion.This writes up is aimed at evaluating ground level concentration of CO2, SO2, NO2 and total hydrocarbon (THC, which are product of gas flared in oil producing areas. Volumes of gas flared at different flow station were collected as well as geometrical parameters. The results of simulation of model developed based on the principles of gaseous dispersion by Gaussian showed a good agreement with dispersion pattern.The results showed that the dispersion pattern of pollutants at ground level depends on the volume of gas flared, wind speed, velocity of discharge and nearness to the source of flaring. The results shows that continuous gas flaring irrespective of the quantity deposited in the immediate environment will in long run lead to change in the physicochemical properties of soil.

  6. Petroleum product refining: plant level analysis of costs and competitiveness. Implications of greenhouse gas emission reductions. Vol 1

    International Nuclear Information System (INIS)

    Kelly, S.J.; Crandall, G.R.; Houlton, G.A.; Kromm, R.B.

    1999-01-01

    Implications on the Canadian refining industry of reducing greenhouse gas (GHG) emissions to meet Canada's Kyoto commitment are assessed, based on a plant-level analysis of costs, benefits and economic and competitive impacts. It was determined on the basis of demand estimates prepared by Natural Resources Canada that refining industry carbon dioxide emissions could be as much a 38 per cent higher than 1990 levels in 2010. Achieving a six per cent reduction below 1990 levels from this business-as-usual case is considered a very difficult target to achieve, unless refinery shutdowns occur. This would require higher imports to meet Canada's petroleum products demand, leaving total carbon dioxide emissions virtually unchanged. A range of options, classified as (1) low capital, operating efficiency projects, (2) medium capital, process/utility optimization projects, (3) high capital, refinery specific projects, and (4) high operating cost GHG projects, were evaluated. Of these four alternatives, the low capital or operating efficiency projects were the only ones judged to have the potential to be economically viable. Energy efficiency projects in these four groups were evaluated under several policy initiatives including accelerated depreciation and a $200 per tonne of carbon tax. Result showed that an accelerated depreciation policy would lower the hurdle rate for refinery investments, and could achieve a four per cent reduction in GHG emissions below 1990 levels, assuming no further shutdown of refinery capacity. The carbon tax was judged to be potentially damaging to the Canadian refinery industry since it would penalize cracking refineries (most Canadian refineries are of this type); it would provide further uncertainty and risk, such that industry might not be able to justify investments to reduce emissions. The overall assessment is that the Canadian refinery industry could not meet the pro-rata Kyoto GHG reduction target through implementation of economically

  7. Transparency, consultation and conflict: Assessing the micro-level risks surrounding the drive to develop Peru's Amazonian oil and gas resources

    DEFF Research Database (Denmark)

    Haselip, James Arthur

    2011-01-01

    Since the 1990s, successive Governments in Peru have sought to expand the exploration and production of the country's oil and gas resources. This economic agenda poses significant opportunities and risks which are usually considered at the macro-level and framed by debates regarding the so....... In the case of Peru, this is especially relevant to the vast areas of ecologically sensitive and previously under-developed Amazonia that are now under concession to oil and gas companies. Low levels of industry transparency combined with a lack of uniform free, prior and informed consent are exacerbating...

  8. RESIDUES IN CARROTS TREATED WITH LINURON

    DEFF Research Database (Denmark)

    Løkke, Hans

    1974-01-01

    Investigations have been carried out on residues of linuron and its breakdown products in carrots sprayed with Jinuron at 1, 2, or 4 kg a.i./ha, 0, 19, 28, 36 or 60 days after sowing (up to 57 days before harvesting). The extracted residues were separated into three fractions by liquid......,4-dichloroaniline and iodide ion, followed by gas chromatography with electron capture detector. Only 5-13% of the extract-able residues were breakdown products. Most of the detectable residue (87-95%) was identified as linuron. The relative proportions of linuron and breakdown products in carrots at the time...

  9. Steady-State Flammable Gas Release Rate Calculation And Lower Flammability Level Evaluation For Hanford Tank Waste

    International Nuclear Information System (INIS)

    Meacham, J.E.

    2009-01-01

    This report assesses the steady state flammability level under off normal ventilation conditions in the tank headspace for 28 double-shell tanks (DST) and 149 single shell-tanks (SST) at the Hanford Site. Flammability was calculated using estimated gas release rates, Le Chatelier's rule, and lower flammability limits of fuels in an air mixture. This revision updates the hydrogen generation rate input data for all 177 tanks using waste composition information from the Best Basis Inventory Detail Report (data effective as of August 4,2008). Assuming only barometric breathing, the shortest time to reach 25% of the lower flammability limit is 11 days for DSTs (i.e., tank 241-AZ-10l) and 36 days for SSTs (i.e., tank 241-B-203). Assuming zero ventilation, the shortest time to reach 25% of the lower flammability limit is 10 days for DSTs (i.e., tank 241-AZ-101) and 34 days for SSTs (i.e., tank 241-B-203).

  10. Steady-State Flammable Gas Release Rate Calculation And Lower Flammability Level Evaluation For Hanford Tank Waste

    International Nuclear Information System (INIS)

    Meacham, J.E.

    2008-01-01

    This report assesses the steady state flammability level under off normal ventilation conditions in the tank headspace for 28 double-shell tanks (DST) and 149 single shell-tanks (SST) at the Hanford Site. Flammability was calculated using estimated gas release rates, Le Chatelier's rule, and lower flammability limits of fuels in an air mixture. This revision updates the hydrogen generation rate input data for al1 177 tanks using waste composition information from the Best Basis Inventory Detail Report (data effective as of August 4,2008). Assuming only barometric breathing, the shortest time to reach 25% of the lower flammability limit is 13 days for DSTs (i.e., tank 241-AZ-102) and 36 days for SSTs (i.e., tank 241-B-203). Assuming zero ventilation, the shortest time to reach 25% of the lower flammability limit is 12 days for DSTs (i.e., tank 241-AZ-102) and 34 days for SSTs (i.e., tank 241-B-203).

  11. Achievement of the level 1 PSA in support to the CEA 2400 MWth gas-cooled fast reactor

    International Nuclear Information System (INIS)

    Balmain, M.; Bassi, C.; Azria, P.

    2012-01-01

    Within Generation IV International Forum, the CEA has developed since 2006 a Level 1 PSA to support the design of the 2400 MWth GFR (Gas-cooled Fast Reactor). A first period, with insights published in 2008, consisted in a model with few initiators representative of medium and high pressure situations, those used for the deterministic design of the Decay Heat Removal (DHR) dedicated loops. In a second period, an iterative work reached the probabilistic targets used for generation III reactors, with prior use of normal loops, and increase of DHR reliability in high pressure conditions. The PSA team covered all the internal initiators, and supported the design of components with instrumentation and control and electrical supplies, and the shutdown operating modes of secondary, tertiary circuits, with possible re-alignment to dedicated DHR loops. Besides, the completed PSA integrated more realistic success criteria than the preliminary model and than the deterministic approach, thanks to CATHARE2 code. In case of loss of Forced Convection, the probability of success of the Natural Convection DHR was assessed by a reliability method for passive systems. The paper underlines the PSA methodology knowledge from the EDF expertise, the improvements co-developed with CEA, and the iteration design-PSA-design. (authors)

  12. Statistical inference on residual life

    CERN Document Server

    Jeong, Jong-Hyeon

    2014-01-01

    This is a monograph on the concept of residual life, which is an alternative summary measure of time-to-event data, or survival data. The mean residual life has been used for many years under the name of life expectancy, so it is a natural concept for summarizing survival or reliability data. It is also more interpretable than the popular hazard function, especially for communications between patients and physicians regarding the efficacy of a new drug in the medical field. This book reviews existing statistical methods to infer the residual life distribution. The review and comparison includes existing inference methods for mean and median, or quantile, residual life analysis through medical data examples. The concept of the residual life is also extended to competing risks analysis. The targeted audience includes biostatisticians, graduate students, and PhD (bio)statisticians. Knowledge in survival analysis at an introductory graduate level is advisable prior to reading this book.

  13. Assessment of pesticide residues in vegetables from the Western Usambara and Uruguru Mountains in Tanzania.

    Science.gov (United States)

    Mtashobya, Lewis A

    2017-09-25

    Assessment of levels of pesticide residues in vegetables was carried out in some villages in the Western Usambara and Uluguru Mountains of Tanzania where varieties of vegetables are grown. Tomatoes and cabbages were the most popular enterprise grown all year round and therefore were selected as the model crops for this study. Analysis of the cleaned sample extracts on a gas chromatography with electron capture detector (GC-ECD) and confirmation on the Gas chromatography-mass spectrometry (GC-MS) revealed dominance of organochlorine pesticides. Organophosphorous pesticides (parathion and marathion) were only detected in some samples, however, in most cases with higher concentrations compared to organochlorine pesticides. Levels of pesticide residues detected in vegetables were up to: parathion 5.07 μg/Kg, marathion 3.73 μg/Kg, α-endosulfan 0.32 μg/Kg, β-endosulfan 0.53 μg/Kg, dieldrin 1.36 μg/Kg, γ-HCH 0.25 μg/Kg, α-HCH 0.09 μg/Kg, and p, p'-DDT 0.64 μg/Kg. These results clearly show that vegetables are contaminated with different pesticide residues. However, the total levels of pesticide residues in both tomatoes and cabbages are lower than their respective codex alimentarius maximum residue levels (MRLs). This means that the vegetables produced in the area are suitable for human consumption.

  14. Monitoring of Pesticide Residues in Commonly Used Fruits and Vegetables in Kuwait.

    Science.gov (United States)

    Jallow, Mustapha F A; Awadh, Dawood G; Albaho, Mohammed S; Devi, Vimala Y; Ahmad, Nisar

    2017-07-25

    The presence of pesticide residues in primary and derived agricultural products raises serious health concerns for consumers. The aim of this study was to assess the level of pesticide residues in commonly consumed fruits and vegetables in Kuwait. A total of 150 samples of different fresh vegetables and fruits were analyzed for the presence of 34 pesticides using the quick easy cheap effective rugged and safe (QuEChERS) multi-residue extraction, followed by gas chromatography-mass spectrometry (GC-MS) or liquid chromatography-tandem mass spectrometry (LC - MS / MS). Pesticide residues above the maximum residue limits (MRL) were detected in 21% of the samples and 79% of the samples had no residues of the pesticides surveyed or contained residues below the MRL. Multiple residues were present in 40% of the samples with two to four pesticides, and four samples were contaminated with more than four pesticide residues. Of the pesticides investigated, 16 were detected, of which imidacloprid, deltamethrin, cypermethrin, malathion, acetamiprid, monocrotophos, chlorpyrifos-methyl, and diazinon exceeded their MRLs. Aldrin, an organochlorine pesticide, was detected in one apple sample, with residues below the MRL. The results indicate the occurrence of pesticide residues in commonly consumed fruits and vegetables in Kuwait, and pointed to an urgent need to develop comprehensive intervention measures to reduce the potential health risk to consumers. The need for the regular monitoring of pesticide residues and the sensitization of farmers to better pesticide safety practices, especially the need to adhere to recommended pre-harvest intervals is recommended.

  15. Monitoring of Pesticide Residues in Commonly Used Fruits and Vegetables in Kuwait

    Directory of Open Access Journals (Sweden)

    Mustapha F. A. Jallow

    2017-07-01

    Full Text Available The presence of pesticide residues in primary and derived agricultural products raises serious health concerns for consumers. The aim of this study was to assess the level of pesticide residues in commonly consumed fruits and vegetables in Kuwait. A total of 150 samples of different fresh vegetables and fruits were analyzed for the presence of 34 pesticides using the quick easy cheap effective rugged and safe (QuEChERS multi-residue extraction, followed by gas chromatography-mass spectrometry (GC-MS or liquid chromatography-tandem mass spectrometry (LC-MS/MS. Pesticide residues above the maximum residue limits (MRL were detected in 21% of the samples and 79% of the samples had no residues of the pesticides surveyed or contained residues below the MRL. Multiple residues were present in 40% of the samples with two to four pesticides, and four samples were contaminated with more than four pesticide residues. Of the pesticides investigated, 16 were detected, of which imidacloprid, deltamethrin, cypermethrin, malathion, acetamiprid, monocrotophos, chlorpyrifos-methyl, and diazinon exceeded their MRLs. Aldrin, an organochlorine pesticide, was detected in one apple sample, with residues below the MRL. The results indicate the occurrence of pesticide residues in commonly consumed fruits and vegetables in Kuwait, and pointed to an urgent need to develop comprehensive intervention measures to reduce the potential health risk to consumers. The need for the regular monitoring of pesticide residues and the sensitization of farmers to better pesticide safety practices, especially the need to adhere to recommended pre-harvest intervals is recommended.

  16. Trace gas emissions from combustion of peat, crop residue, domestic biofuels, grasses, and other fuels: configuration and Fourier transform infrared (FTIR) component of the fourth Fire Lab at Missoula Experiment (FLAME-4)

    Science.gov (United States)

    Stockwell, C. E.; Yokelson, R. J.; Kreidenweis, S. M.; Robinson, A. L.; DeMott, P. J.; Sullivan, R. C.; Reardon, J.; Ryan, K. C.; Griffith, D. W. T.; Stevens, L.

    2014-09-01

    During the fourth Fire Lab at Missoula Experiment (FLAME-4, October-November 2012) a large variety of regionally and globally significant biomass fuels was burned at the US Forest Service Fire Sciences Laboratory in Missoula, Montana. The particle emissions were characterized by an extensive suite of instrumentation that measured aerosol chemistry, size distribution, optical properties, and cloud-nucleating properties. The trace gas measurements included high-resolution mass spectrometry, one- and two-dimensional gas chromatography, and open-path Fourier transform infrared (OP-FTIR) spectroscopy. This paper summarizes the overall experimental design for FLAME-4 - including the fuel properties, the nature of the burn simulations, and the instrumentation employed - and then focuses on the OP-FTIR results. The OP-FTIR was used to measure the initial emissions of 20 trace gases: CO2, CO, CH4, C2H2, C2H4, C3H6, HCHO, HCOOH, CH3OH, CH3COOH, glycolaldehyde, furan, H2O, NO, NO2, HONO, NH3, HCN, HCl, and SO2. These species include most of the major trace gases emitted by biomass burning, and for several of these compounds, this is the first time their emissions are reported for important fuel types. The main fire types included African grasses, Asian rice straw, cooking fires (open (three-stone), rocket, and gasifier stoves), Indonesian and extratropical peat, temperate and boreal coniferous canopy fuels, US crop residue, shredded tires, and trash. Comparisons of the OP-FTIR emission factors (EFs) and emission ratios (ERs) to field measurements of biomass burning verify that the large body of FLAME-4 results can be used to enhance the understanding of global biomass burning and its representation in atmospheric chemistry models. Crop residue fires are widespread globally and account for the most burned area in the US, but their emissions were previously poorly characterized. Extensive results are presented for burning rice and wheat straw: two major global crop residues

  17. The Effect of Increased Salinity and Temperature in Peat Soils from the Everglades: Implications for Biogenic Gas Production and Release Under a Sea Level Rise Scenario

    Science.gov (United States)

    Sirianni, M.; Comas, X.

    2015-12-01

    Sea level rise (SLR) is an increasingly important topic for many low-lying coastal areas such as South Florida. The United States Army Corps of Engineers (USACE) projects that sea level change in South Florida, over the next 50 years, will increase between 0.1 and 0.6 meters. Given the low elevation and its shallow slope, the Everglades region is highly susceptible to changes in sea level. Based on the USACE SLR projections it seems inevitable that previously unexposed freshwater areas of the southern Everglades will become increasingly exposed to saline water. The effects of such saline water intrusion into the current C dynamics of the Everglades (particularly in terms of biogenic gas production and emissions, i.e. CH4 and CO2) is however uncertain. As previously proposed by others, increases in salinity in peat soils will result in dilation of pore spaces and thus increases in hydraulic conductivity, while limiting methanogenesis. However, increases in temperature may induce the opposite effect, particularly in terms of methanogenic activity. Previous studies investigating the effects of increased salinity on freshwater peat soils in the Everglades are very limited, and to our knowledge none have intended to monitor the internal gas dynamics within the peat matrix using an array of geophysical and hydrological methods such as ground penetrating radar (GPR), time-lapse photography, gas chromatography, and constant head permeameter tests. Preliminary laboratory results showed (1) a progressive decrease in gas content within the peat matrix (i.e. production) and gas releases once fluid conductivity is increased; (2) a progressive increase in hydraulic conductivity once fluid conductivity is increased; and (3) maximum gas releases detected during early stages of pore dilation (after increasing salinity) followed by a progressive decrease in gas release as salinity increased. This study has implications for better understanding how C dynamics in the Everglades may be

  18. Determination of low-level agricultural residues in soft drinks and sports drinks by liquid chromatography/tandem mass spectrometry: single-laboratory validation.

    Science.gov (United States)

    Paske, Nathan; Berry, Bryan; Schmitz, John; Sullivan, Darryl

    2007-01-01

    In this study, sponsored by PepsiCo Inc., a method was validated for measurement of 11 pesticide residues in soft drinks and sports drinks. The pesticide residues determined in this validation were alachlor, atrazine, butachlor, isoproturon, malaoxon, monocrotophos, paraoxon-methyl, phorate, phorate sulfone, phorate sulfoxide, and 2,4-dichlorophenoxyacetic acid (2,4-D) when spiked at 0.100 microg/L (1.00 microg/L for phorate). Samples were filtered (if particulate matter was present), degassed (if carbonated), and analyzed using liquid chromatography with tandem mass spectrometry. Quantitation was performed with matrix-matched external standard calibration solutions. The standard curve range for this assay was 0.0750 to 10.0 microg/L. The calibration curves for all agricultural residues had coefficient of determination (r2) values greater than or equal to 0.9900 with the exception of 2 values that were 0.9285 and 0.8514. Fortification spikes at 0.100 microg/L (1.00 microg/L for phorate) over the course of 2 days (n=8 each day) for 3 matrixes (7UP, Gatorade, and Diet Pepsi) yielded average percent recoveries (and percent relative standard deviations) as follows (n=48): 94.4 (15.2) for alachlor, 98.2 (13.5) for atrazine, 83.1 (41.6) for butachlor, 89.6 (24.5) for isoproturon, 87.9 (24.4) for malaoxon, 96.1 (9.26) for monocrotophos, 101 (25.7) for paraoxon-methyl, 86.6 (20.4) for phorate, 101 (16.5) for phorate sulfone, 93.6 (25.5) for phorate sulfoxide, and 98.2 (6.02) for 2,4-D.

  19. Estratégias de amostragem para determinação do nitrato residual no solo após o cultivo do tomateiro adubado em sulcos = Sampling strategies for determining residual nitrate soil levels after growing tomatoes in fertilized furrows

    Directory of Open Access Journals (Sweden)

    Charles de Araújo

    2010-07-01

    Full Text Available O efeito de diferentes critérios para o manejo da adubação nitrogenada e do posicionamento de amostragem para a quantificação do N-NO3 residual no solo foi determinado após o cultivo do tomateiro adubado por sulcos. Dois experimentos foram conduzidos, no campo sem proteção, com aplicação de adubo sólido e irrigação por sulcos. Em cada experimento, os tratamentos foram arranjados em parcela subdivida, com dez critérios para o manejo da adubação nitrogenada na parcela e posições de amostragem do solo na subparcela. Esses foram arranjados no delineamento experimental de blocos ao acaso. Foi determinado o teor de N-NO3 no solo de amostras retiradas no final do ciclo de cada experimento, em diferentes posições. Em todos os experimentos o teor de N-NO3 residual no solo foi proporcional àquantidade de N aplicada nos diferentes critérios. Em condições de campo sem proteção e fertilizante nitrogenado aplicado em sulco, a melhor estratégia de amostragem do solo para a determinação do teor de N-NO3 residual foi obtida pela utilização de amostra composta tomada em posições sobre o sulco e entre o sulco e as plantas.Management of nitrogen fertilizer programs and sampling strategies to determine the levels of N-NO3 in the soil after growing tomatoes in fertilized furrows were studied. Two groups were studied, one without protection and another grown in an irrigated furrow in which a solid nitrogen fertilizer had been applied. In each plot, 10 treatments or criteria were evaluated. In each experiment, the treatments were arranged in a split-plot design, with 10 different nitrogen fertilizer conditions as the main treatment and soil sampling positions in a split-plot treatment. The sampling positions were arranged in a randomized complete block design. Soil N-NO3 levels were determined at the end of each sampling cycle. In all groups, residual soil N-NO3 levels were proportional to the amount of N applied. In fields without

  20. ASSESSMENT OF DIVERSITY OF POLISH VOIVODSHIPS BY LEVEL OF GAS PIPELINE INFRASTRUCTURE DEVELOPMENT USING MULTIDIMENSIONAL COMPARATIVE ANALYSIS

    Directory of Open Access Journals (Sweden)

    Marek URBANIK

    2016-06-01

    Full Text Available In the paper differentiation of gas pipeline infrastructure development in the Polish voivodships was presented. To illustrate this diversity the method of cluster analysis is used, obtained on the basis of statistical data collected by the Central Statistical Office (CSO. In order to conduct a preliminary review procedure for classification of individual provinces in relation to the assessment of the development of gas pipeline infrastructure linear classification was used, involved determining synthetic measure, which is the average of the variable components, through which voivodships were ordered. In order to estimate the distance between the clusters the variance analysis was used with the implementation of the Ward method. The analysis was performed on the basis of the following indicators: average increase in length of the gas network (an average for the total voivodoship 164.2 km, growth of the gas network in comparison to the first year of observation (123%, number of gas connections per 1 km of gas pipe (18.87 no∙km-1, the length of the network per unit area (5.37 m∙ha-1, intensity of network loading (84.15 m3∙d-1∙km-1, inhabitants having access to the gas system in % of total population (51.33%. In the analysis five clusters were grouped. Critical value was determined and segregation of individual clusters was made, taking into account the dominant parameters.

  1. Life cycle assessment of greenhouse gas emissions and water-energy optimization for shale gas supply chain planning based on multi-level approach: Case study in Barnett, Marcellus, Fayetteville, and Haynesville shales

    International Nuclear Information System (INIS)

    Chen, Yizhong; He, Li; Guan, Yanlong; Lu, Hongwei; Li, Jing

    2017-01-01

    Highlights: • Detailed model developed for the shale gas supply chain system in the US. • Dynamic integration of multi-level programming and life cycle assessment. • Analysis of the objectives with environmental, economic and energy concerns. • Identification of GHG emissions and water-energy consumption at life cycle stages. • Comparison of management performances obtained from the MLP, MOP, and BLP methods. - Abstract: This study develops a multi-level programming model from a life cycle perspective for performing shale-gas supply chain system. A set of leader-follower-interactive objectives with emphases of environmental, economic and energy concerns are incorporated into the synergistic optimization process, named MGU-MEM-MWL model. The upper-level model quantitatively investigates the life-cycle greenhouse gas (GHG) emissions as controlled by the environmental sector. The middle-level one focuses exclusively on system benefits as determined by the energy sector. The lower-level one aims to recycle water to minimize the life-cycle water supply as required by the enterprises. The capabilities and effectiveness of the developed model are illustrated through real-world case studies of the Barnett, Marcellus, Fayetteville, and Haynesville Shales in the US. An improved multi-level interactive solution algorithm based on satisfactory degree is then presented to improve computational efficiency. Results indicate that: (a) the end-use phase (i.e., gas utilization for electricity generation) would not only dominate the life-cycle GHG emissions, but also account for 76.1% of the life-cycle system profits; (b) operations associated with well hydraulic fracturing would be the largest contributor to the life-cycle freshwater consumption when gas use is not considered, and a majority of freshwater withdrawal would be supplied by surface water; (c) nearly 95% of flowback water would be recycled for hydraulic fracturing activities and only about 5% of flowback water

  2. Pyrethroid residue dynamics in insects depends on the circadian clock.

    Science.gov (United States)

    Maliszewska, Justyna; Piechowicz, Bartosz; Maciąga, Gabriela; Zaręba, Lech; Marcinkowska, Sonia

    2018-02-27

    Many factors may affect pesticide effectiveness against pests. One of the factors that should be considered is circadian rhythmicity. In this study, we evaluated daily variations in pyrethroid susceptibility in the house cricket, Acheta domesticus L. Crickets were exposed to a standard dose of ß-cyfluthrin at different times of a day, and pesticide residue levels were evaluated using gas chromatography. Results demonstrate that the time of pyrethroid disappearance is correlated with the circadian clock, with the highest decomposition rate at night. Furthermore, crickets also showed the highest resistance to the insecticide at night, expressed as a high survival rate. Moreover, ß-cyfluthrin induced significant changes in thermal preferences of intoxicated crickets. This is the first report showing that pyrethroid