WorldWideScience

Sample records for residual gas conduction

  1. Residual gas analysis

    International Nuclear Information System (INIS)

    Berecz, I.

    1982-01-01

    Determination of the residual gas composition in vacuum systems by a special mass spectrometric method was presented. The quadrupole mass spectrometer (QMS) and its application in thin film technology was discussed. Results, partial pressure versus time curves as well as the line spectra of the residual gases in case of the vaporization of a Ti-Pd-Au alloy were demonstrated together with the possible construction schemes of QMS residual gas analysers. (Sz.J.)

  2. RESIDUAL RISK ASSESSMENT: GAS DISTRIBUTION STAGE ...

    Science.gov (United States)

    This document describes the residual risk assessment for the Gas Distribution Stage 1 souce category. For stationary sources, section 112 (f) of the Clean Air Act requires EPA to assess risks to human health and the environment following implementation of technology-based control standards. If these technology-based control standards do not provide an ample margin of safety, then EPA is required to promulgate addtional standards. This document describes the methodology and results of the residual risk assessment performed for the Gas Distribution Stage 1 source category. The results of this analyiss will assist EPA in determining whether a residual risk rule for this source category is appropriate.

  3. Profile Monitors Based on Residual Gas Interaction

    CERN Document Server

    Forck, P; Giacomini, T; Peters, A

    2005-01-01

    The precise determination of transverse beam profiles at high current hadron accelerators has to be performed non-interceptingly. Two methods will be discussed based on the excitation of the residual gas molecules by the beam particles: Firstly, by beam induced fluorescence (BIF) light is emitted from the residual gas molecules and is observed with an image intensified CCD camera. At most laboratories N2 gas is inserted, which has a large cross section for emission in the blue wave length region. Secondly, a larger signal strength is achieved by detecting the ionization products in an Ionization Profile Monitor (IPM). By applying an electric field all ionization products are accelerated toward a spatial resolving Micro-Channel Plate. The signal read-out can either be performed by observing the light from a phosphor screen behind the MCP or electronically by a wire array. Methods to achieve a high spatial resolution and a fast turn-by-turn readout capability are discussed. Even though various approaches at dif...

  4. Chloroxyanion residues in cantaloupe and tomatoes after chlorine dioxide gas sanitation

    Science.gov (United States)

    Chlorine dioxide gas is effective at cleansing fruits and vegetables of bacterial pathogens and(or) rot organisms, but few data are available on chemical residues remaining subsequent to chlorine gas treatment. Therefore, studies were conducted to quantify chlorate and perchlorate residues after tom...

  5. Gas storage carbon with enhanced thermal conductivity

    Science.gov (United States)

    Burchell, Timothy D.; Rogers, Michael Ray; Judkins, Roddie R.

    2000-01-01

    A carbon fiber carbon matrix hybrid adsorbent monolith with enhanced thermal conductivity for storing and releasing gas through adsorption and desorption is disclosed. The heat of adsorption of the gas species being adsorbed is sufficiently large to cause hybrid monolith heating during adsorption and hybrid monolith cooling during desorption which significantly reduces the storage capacity of the hybrid monolith, or efficiency and economics of a gas separation process. The extent of this phenomenon depends, to a large extent, on the thermal conductivity of the adsorbent hybrid monolith. This invention is a hybrid version of a carbon fiber monolith, which offers significant enhancements to thermal conductivity and potential for improved gas separation and storage systems.

  6. The new method for the residual gas density measurements

    CERN Document Server

    Anashin, V V; Krasnov, A A; Malyshev, O B; Nas'mov, V P; Pyata, E I; Shaftan, T V

    2001-01-01

    A new method of measurement for residual gas density in the vacuum chambers in presence of synchrotron radiation (SR) is described. The method is based on using a photomultiplier tube for the detection of the SR-stimulated residual gas luminescence, which is proportional to the residual gas density and SR intensity. The design of the experimental setup and results of the measurements of densities of residual gases (H sub 2 , CO sub 2 , CO, N sub 2 , Ar and O sub 2) are submitted.

  7. Gas Sensors Based on Conducting Polymers

    Directory of Open Access Journals (Sweden)

    Gaoquan Shi

    2007-03-01

    Full Text Available The gas sensors fabricated by using conducting polymers such as polyaniline (PAni, polypyrrole (PPy and poly (3,4-ethylenedioxythiophene (PEDOT as the active layers have been reviewed. This review discusses the sensing mechanism and configurations of the sensors. The factors that affect the performances of the gas sensors are also addressed. The disadvantages of the sensors and a brief prospect in this research field are discussed at the end of the review.

  8. Chloroxyanion Residues in Cantaloupe and Tomatoes after Chlorine Dioxide Gas Sanitation.

    Science.gov (United States)

    Smith, D J; Ernst, W; Herges, G R

    2015-11-04

    Chlorine dioxide gas is effective at cleansing fruits and vegetables of bacterial pathogens and(or) rot organisms, but little data are available on chemical residues remaining subsequent to chlorine gas treatment. Therefore, studies were conducted to quantify chlorate and perchlorate residues after tomato and cantaloupe treatment with chlorine dioxide gas. Treatments delivered 50 mg of chlorine dioxide gas per kg of tomato (2-h treatment) and 100 mg of gas per kg of cantaloupe (6-h treatment) in sealed, darkened containers. Chlorate residues in tomato and cantaloupe edible flesh homogenates were less than the LC-MS/MS limit of quantitation (60 and 30 ng/g respectively), but were 1319 ± 247 ng/g in rind + edible flesh of cantaloupe. Perchlorate residues in all fractions of chlorine dioxide-treated tomatoes and cantaloupe were not different (P > 0.05) than perchlorate residues in similar fractions of untreated tomatoes and cantaloupe. Data from this study suggest that chlorine dioxide sanitation of edible vegetables and melons can be conducted without the formation of unwanted residues in edible fractions.

  9. A modeled experiment of gas behavior in aquifer and residual gas formation

    Science.gov (United States)

    Takahashi, K.; Yamada, Y.; Murata, S.; Nakano, M.; Matsuoka, T.

    2007-12-01

    National and international concern is rising about the possible effects of greenhouse gases (GHGs) on the climate. Several methods are proposed to reduce the gas in the atmosphere and underground sequestration is recently expected as an effective concept. Especially, residual gas can be the most effective method to store the gas in reservoir. Underground sequestration requires the gas injected into a reservoir. When the gas is injected into a water- saturated aquifer, it pushes water out of the pore space. As the gas bubbles go upward, the gas space is filled with water again, but small gas bubbles are trapped in the pore space by surface force and capillary pressure of water. This is the residual gas formation. Once the residual gas is formed, it seldom moves again from the pore space. Residual gas formation needs neither cap-rock nor structural trap, thus has a potential to be applied to broader regions. The purpose of this study is to examine the fundamental mechanism of residual gas formation and gas migration underground by injecting the gas into a modeled and visualized aquifer. We designed and constructed an experimental apparatus to measure the distribution and the saturation of the residual gas. We used glass beads of 1 or 2mm diameters as porous media to construct some reservoir models that have various porosity, permeability, and wettability. The glass beads packed in our apparatus which has 30cm width, 33.5cm height, and 1cm thickness. It has 1§¤volume in amount. The pore space was filled with viscous liquid, then air was injected from the bottom. Some conditions in the injection time and rate were tested. We observed air behavior and measured the volume of the distribution area of residual gas from its digital photographs, and the volume of residual gas from the amount of water that was pushed out from the apparatus. The experimental results showed that differences of reservoir properties made changes in the gas behavior and residual gas volume. It

  10. Washing of Rocky Flats Combustible Residues (Conducted March - May 1995)

    Energy Technology Data Exchange (ETDEWEB)

    Mary E. Barr; Ann R. Schake; David A. Romero; Gordon D. Jarvinen

    1999-03-01

    The scope of this project is to determine the feasibility of washing plutonium-containing combustible residues using ultrasonic disruption as a method for dislodging particulate. Removal of plutonium particulate and, to a lesser extent, solubilized plutonium from the organic substrate should substantially reduce potential fire, explosion or radioactive release hazards due to radiolytic hydrogen generation or high flammability. Tests were conducted on polypropylene filters which were used as pre-filters in the rich-residue ion-exchange process at the Los Alamos Plutonium Facility. These filters are similar to the Ful-Flo{reg_sign} cartridges used at Rocky Flats that make up a substantial fraction of the combustible residues with the highest hazard rating. Batch experiments were run on crushed filter material in order to determine the amount of Pu removed by stirring, stirring and sonication, and stirring and sonication with the introduction of Pu-chelating water-soluble polymers or surfactants. Significantly more Pu is removed using sonication and sonication with chelators than is removed with mechanical stirring alone.

  11. Graphic Three-Axes Presentation of Residual Gas Analyser Data

    Science.gov (United States)

    Johnson, Kenneth R.; Levi, Alejandro G.

    1996-01-01

    Residual gas analyzers (RGA) are commonly used to measure the composition of residual gases in thermal-vacuum test chambers. Measurements from RGAs are often used to identify and quantify outgassing contaminants from a test article during thermal-vacuum testing. RGA data is typically displayed as snapshots in time, showing instantaneous concentrations of ions from ionized residual gas molecules at different atomic masses. A method was devised by the authors to present RGA data in a three-axis format, plotting atomic mass unit (AMU), ion concentration as a function of AMU, and time, to provide a clear graphic visualization ot trends in gas concentration changes and to initiate a valuable analytical tool to interpret test article outgassing rates during thermal-vacuum testing.

  12. Evaluation of chlorine dioxide gas residues on selected food produce.

    Science.gov (United States)

    Trinetta, Valentina; Vaidya, Nirupama; Linton, Richard; Morgan, Mark

    2011-01-01

    In recent years, the consumption of fresh fruits and vegetables has greatly increased, and so has its association with contamination of several foodborne pathogens (Listeria, Salmonella, and Escherichia coli). Hence, there is a need to investigate effective sanitizer systems for produce decontamination. Chlorine dioxide (ClO(2)), a strong oxidizing gas with broad spectrum and sanitizing properties, has previously been studied for use on selected fruits and vegetables. ClO(2) gas treatments show great potential for surface pathogen reduction; however its use from a residue safety standpoint has yet to be assessed. Thus, the objective of this study was to evaluate residues of ClO(2), chlorite, chlorate, and chloride on selected fresh produce surfaces after treatment with ClO(2) gas. A rinse procedure was used and water samples were analyzed by N, N-diethyl-p-phenylenediamine and ion chromatography method (300.0). Seven different foods--tomatoes, oranges, apples, strawberries, lettuce, alfalfa sprouts, and cantaloupe--were analyzed after ClO(2) treatment for surface residues. Very low residues were detectable for all the food products except lettuce and alfalfa sprouts, where the measured concentrations were significantly higher. Chlorine dioxide technology leaves minimal to no detectable chemical residues in several food products, thus result in no significant risks to consumers. Practical Application: Potential for chlorine dioxide gas treatments as an effective pathogen inactivation technology to produce with minimal risk for consumers.

  13. Residue management in the Bolivia-Brazil gas pipeline construction

    International Nuclear Information System (INIS)

    Freitas, Eduardo Lopes; Henrique, Paulo Roberto Pereira; Cantarino, Anderson Americo Alves

    2000-01-01

    The construction of the gas pipeline is a process sequential of assembly phases, where each one of those phases generates residues of the most varied types and amounts, being necessary the forecast of your generation in agreement with the activity that is being executed. During the accomplishment of the works they are generated a lot of times situations where are observed the inadequate disposition of the residues. Those practices, besides the environmental impact that they cause, it can cart in the future, the need of additional investments be proceeded in the recovery of the areas and removal of the residues. This work presents the Program of administration of Residues instituted during the construction of the pipeline Bolivia - Brazil, seeking, on a side to reduce to the minimum the generation of residues and of the other, moths handling guidelines and disposition, in way to minimize the environmental impacts caused by the same ones. (author)

  14. CO2 storage in depleted gas reservoirs: A study on the effect of residual gas saturation

    Directory of Open Access Journals (Sweden)

    Arshad Raza

    2018-03-01

    Full Text Available Depleted gas reservoirs are recognized as the most promising candidate for carbon dioxide storage. Primary gas production followed by injection of carbon dioxide after depletion is the strategy adopted for secondary gas recovery and storage practices. This strategy, however, depends on the injection strategy, reservoir characteristics and operational parameters. There have been many studies to-date discussing critical factors influencing the storage performance in depleted gas reservoirs while little attention was given to the effect of residual gas. In this paper, an attempt was made to highlight the importance of residual gas on the capacity, injectivity, reservoir pressurization, and trapping mechanisms of storage sites through the use of numerical simulation. The results obtained indicated that the storage performance is proportionally linked to the amount of residual gas in the medium and reservoirs with low residual fluids are a better choice for storage purposes. Therefore, it would be wise to perform the secondary recovery before storage in order to have the least amount of residual gas in the medium. Although the results of this study are useful to screen depleted gas reservoirs for the storage purpose, more studies are required to confirm the finding presented in this paper.

  15. Fuel gas production from animal residue. Dynatech report No. 1551

    Energy Technology Data Exchange (ETDEWEB)

    Ashare, E.; Wise, D.L.; Wentworth, R.L.

    1977-01-14

    A comprehensive mathematical model description of anaerobic digestion of animal residues was developed, taking into account material and energy balances, kinetics, and economics of the process. The model has the flexibility to be applicable to residues from any size or type of animal husbandry operation. A computer program was written for this model and includes a routine for optimization to minimum unit gas cost, with the optimization variables being digester temperature, retention time, and influent volatile solids concentration. The computer program was used to determine the optimum base-line process conditions and economics for fuel gas production via anaerobic digestion of residues from a 10,000 head environmental beef feedlot. This feedlot at the conditions for minimum unit gas cost will produce 300 MCF/day of methane at a cost of $5.17/MCF (CH/sub 4/), with a total capital requirement of $1,165,000, a total capital investment of $694,000, and an annual average net operating cost of $370,000. The major contributions to this unit gas cost are due to labor (37 percent), raw manure (11 percent), power for gas compression (10 percent), and digester cost (13 percent). A conceptual design of an anaerobic digestion process for the baseline conditions is presented. A sensitivity analysis of the unit gas cost to changes in the major contributions to unit gas cost was performed, and the results of this analysis indicate areas in the anaerobic digestion system design where reasonable improvements could be expected so as to produce gas at an economically feasible cost. This sensitivity analysis includes the effects on unit gas cost of feedlot size and type, digester type, digester operating conditions, and economic input data.

  16. Fuel gas production from animal and agricultural residues and biomass

    Energy Technology Data Exchange (ETDEWEB)

    Wise, D. L; Wentworth, R. L

    1978-05-30

    Progress was reported by all contractors. Topics presented include: solid waste to methane gas; pipeline fuel gas from an environmental cattle feed lot; heat treatment of organics for increasing anaerobic biodegradability; promoting faster anaerobic digestion; permselective membrane control of algae and wood digesters for increased production and chemicals recovery; anaerobic fermentation of agricultural residues; pilot plant demonstration of an anaerobic, fixed-film bioreactor for wastewater treatment; enhancement of methane production in the anaerobic diegestion of sewage; evaluation of agitation concepts for biogasification of sewage sludge; operation of a 50,000 gallon anaerobic digester; biological conversion of biomass to methane; dirt feedlot residue experiments; anaerobic fermentation of livestock and crop residues; current research on methanogenesis in Europe; and summary of EPA programs in digestion technology. (DC)

  17. Graphic Three-Axes Presentation of Residual Gas Analyzer Data

    Science.gov (United States)

    Johnson, Kenneth R.; Levi, Alejandro G.

    1997-01-01

    Residual gas analyzers (RGA) are commonly used to measure the composition of residual gases in thermal-vacuum test chambers. Measurements from RGA's are often used to identify and quantify outgassing contaminants from a test article during thermal-vacuum testing. RGA data is typically displayed as snapshots in time, showing instantaneous concentrations of ions from ionized residual gas molecules at different atomic masses. This ion concentration information can be interpreted to be representative of the composition of the residual gas in the chamber at the instant of analysis. Typically, test personnel are most interested in tracking the time history of changes in the composition of chamber residual gas to determine the relative cleanliness and the clean-up rate of the test article under vacuum. However, displays of instantaneous RGA data cannot provide test personnel with the preferred time history information. In order to gain an understanding of gas composition trends, a series of plots of individual data snapshots must be analyzed. This analysis is cumbersome and still does not provide a very satisfactory view of residual gas composition trends. A method was devised by the authors to present RCA data in a three-axis format, plotting Atomic Mass Unit (AMU), the Ionization Signal Response (ISR) as amps/torr as a function of AMU, and Time, to provide a clear graphic visualization of trends of changes in ISR with respect to time and AMU (representative of residual gas composition). This graphic visualization method provides a valuable analytical tool to interpret test article outgassing rates during thermal vacuum tests. Raw RGA data was extracted from a series of delimited ASCII files and then converted to a data array in a spreadsheet. Consequently, using the 3-D plotting functionality provided by the spreadsheet program, 3-D plots were produced. After devising the data format conversion process, the authors began developing a program to provide real-time 3-D

  18. Chloroxyanion Residue Quantification in Cantaloupes Treated with Chlorine Dioxide Gas.

    Science.gov (United States)

    Kaur, Simran; Smith, David J; Morgan, Mark T

    2015-09-01

    Previous studies show that treatment of cantaloupes with chlorine dioxide (ClO2) gas at 5 mg/liter for 10 min results in a significant reduction (P chlorine dioxide ((36)ClO2) gas was used to describe the identity and distribution of chloroxyanion residues in or on cantaloupe subsequent to fumigation with ClO2 gas at a mean concentration of 5.1 ± 0.7 mg/liter for 10 min. Each treated cantaloupe was separated into rind, flesh, and mixed (rind and flesh) sections, which were blended and centrifuged to give the corresponding sera fractions. Radioactivity detected, ratio of radioactivity to mass of chlorite in initial ClO2 gas generation reaction, and distribution of chloroxyanions in serum samples were used to calculate residue concentrations in flesh, rind, and mixed samples. Anions detected on the cantaloupe were Cl(-) (∼ 90%) and ClO3(-) (∼ 10%), located primarily in the rind (19.3 ± 8.0 μg of Cl(-)/g of rind and 4.8 ± 2.3 μg of ClO3(-)/g of rind, n = 6). Cantaloupe flesh (∼ 200 g) directly exposed to(36)ClO2 gas treatment showed the presence of only Cl(-) residues (8.1 ± 1.0 μg of Cl(-)/g of flesh, n = 3). Results indicate chloroxyanion residues Cl(-) and ClO3(-) are only present on the rind of whole cantaloupes treated with ClO2 gas. However during cutting, residues may be transferred to the fruit flesh. Because Cl(-) is not toxic, only ClO3(-) would be a toxicity concern, but the levels transferred from rind to flesh are very low. In the case of fruit flesh directly exposed to ClO2 gas, only nontoxic Cl(-) was detected. This indicates that ClO2 gas that comes into contact with edible flesh would not pose a health concern.

  19. Minimizing Residual Pressure within a Windowless Gas Target System - JENSA

    Science.gov (United States)

    Gomez, Orlando; Browne, Justin; Kontos, Antonios; Montes, Fernando; Jensa Collaboration

    2015-04-01

    Nuclear reactions between light gases and radioactive isotope beams are essential to address open questions in nuclear structure and astrophysics. Pure light gas targets are critical for the measurements of proton- and alpha-induced reactions. J _ et E _ xperiments in N _ uclear S _ tructure and A _ strophysics (JENSA) is the world's most dense (~ 1019 atoms/cm2) windowless gas target system. Most of the gas flow is localized; however, escaping gas creates a pressure gradient which degrades experimental measurements and contaminates the beam line. JENSA contains a differential pumping system to maintain a vacuum. The previous design configuration was not optimized for experiments (pressure measurements 70 cm downstream from the jet were ~ 10-3 torr; optimal is less than 10-4 torr). We have altered the current differential pumping system to minimize the residual pressure profile. Several configurations of two gas-receiving catchers were tested, and the most efficient ones identified using Enhanced Pirani and Cold Cathode gauges. We have determined the 30 mm outer and 20 mm inner gas-receiving cones minimize JENSA central chamber pressure to 200 millitorr at 16,000 torr of discharge pressure. Altering the tubing configuration has additionally lowered the pressure 70 cm downstream to 10-5 torr. The new residual pressure allows operation of JENSA with planned expansion of a recoil mass separator SECAR.

  20. Residual Gas Fluorescence for Profile Measurements at the GSI UNILAC

    CERN Document Server

    Forck, P

    2002-01-01

    The high beam currents, delivered at the LINAC at GSI (UNILAC) can destroy intercepting diagnostics within one macro-pulse. As an alternative for a non-destructive profile measurement the methode for residual-gas-fluorescence is investigated. The fluorescence light is emitted by the N2 molecules of the residual gas at the blue wavelength range and can be monitored with a modern CCD-camera. The images are transferred via digital bus (IEEE 1394 'FireWire') and the profiles are generated by analysis of the images with a modern software tool (National Instruments 'LabView'). Due to the short beam pulses (about 0.2 ms) the light intensities emitted by the residual gas are low and require a high amplification (gain >106) which is realized with an image intensifier with double MCP (multi channel plate), connected with a fiber taper to the CCD-chip. The design parameters of the optics and electronics are discussed as well as the advantages of the digital data transmission. Measurements with heavy ion beams of several...

  1. Residual stresses evaluation in a gas-pipeline crossing

    Energy Technology Data Exchange (ETDEWEB)

    Fonseca, Maria Cindra [Universidade Federal Fluminense (UFF), Niteroi, RJ (Brazil); Almeida, Manoel Messias [COMPAGAS, Curitiba, PR (Brazil); Rebello, Joao Marcos Alcoforado [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil); Souza Filho, Byron Goncalves de [PETROBRAS, Rio de Janeiro, RJ (Brazil)

    2009-07-01

    The X-rays diffraction technique is a well established and effectiveness method in the determination of the residual and applied stresses in fine grained crystalline materials. It allows to characterize and to quantify the magnitude and direction of the existing surface stresses in the studied point of the material. The objective of this work is the evaluation of the surface stresses in a 10 in diameter Natural Gas Distribution Pipeline manufactured from API 5 L Gr B steel of COMPAGAS company, in a crossing with a Natural Gas Transportation Pipeline, in Araucaria-PR. This kind of evaluation is important to establish weather you have to perform a repositioning of one of the pipeline or not. The measurements had been made in two transversal sections of the pipe, the one upstream (170 mm of the external wall of the pipeline) and another one downstream (840 mm of the external wall of the pipeline). Each transversal section measurements where carried out in 3 points: 9 hours, 12 hours and 3 hours. In each measured point of the pipe surface, the longitudinal and transversal stresses had been measured. The magnitude of the surface residual stresses in the pipe varied of +180 MPa at the -210 MPa. The residual stress state on the surface of the points 12 hours region is characterized by tensile stresses and by compressive stresses in the points of 3 and 9 hours region. The surface residual stresses in gas-pipeline have been measured using X-ray diffraction method, by double exposure technique, using a portable apparatus, with Cr-K-alpha radiation. (author)

  2. Monitoring volatilization products using Residual Gas Analyzers during MeV ion beam irradiations

    Science.gov (United States)

    Wetteland, C. J.; Kriewaldt, K.; Taylor, L. A.; McSween, H. Y.; Sickafus, K. E.

    2018-03-01

    The use of Residual Gas Analyzers (RGAs) during irradiation experiments can provide valuable information when incorporated into experimental end-stations. The instruments can track the volatilization products of beam-sensitive materials, which may ultimately aid researchers in selecting appropriate flux values for conducting experiments. Furthermore, the type of gaseous species released during an irradiation can be monitored directly, which may lead to new insights into the radiolysis and/or heating mechanisms responsible for gas evolution. A survey of several classes of materials exposed to extremes in particle flux is presented to show how RGA instrumentation can be incorporated to qualitatively assess ion-solid interactions in a variety of fields.

  3. Determination of gas residues in uranium dioxide pellets

    International Nuclear Information System (INIS)

    Riella, H.G.

    1978-01-01

    The measurement of low amounts of residual gases, excluding water, in ceramic grade uranium dioxide pellets, using high temperature vacuum extraction technique, is dealt with. The high temperature extraction gas analysis apparatus was designed and assembled for sequential analysis of up to eight uranium dioxide pellets by run. The system consists of three major units, namely outgassing unit, transfer unit and analytical unit. The whole system is evacuated to a final pressure of less then 10 -5 torr. A weighed pellet is transfered into the outgassing unit for subsequent dropping into a Platinum-Rhodium crucible which is heated inductively up to 1600 0 C during 30 minutes. The released gases are imediately transfered from the outgassing to analytical unit passing through a cold trap at -95 0 C to remove water vapor. The gases are transfered to previously calibrated volumetric bulb where the total pressure and temperature are determined. An estimate of the gas content in the pellets at STP condition is obtained from the measured volume, pressure and temperature of the gas mixture by applying ideal gases equation. Analysis to two lots (fourteen samples) of uranium dioxide pellets by the method described here indicated a mean gas content of 0,060cm 3 /g UO 2 . The lower limit of this technique is 0,03cm 3 /g UO 2 (STP). The time required for the analysis of eight pellets is about 9 hours [pt

  4. Fungicide residue identification and discrimination using a conducting polymer electronic-nose

    Science.gov (United States)

    Alphus D. Wilson

    2013-01-01

    The identification of fungicide residues on crop foliage is necessary to make periodic pest management decisions. The determination of fungicide residue identities currently is difficult and time consuming using conventional chemical analysis methods such as gas chromatography-mass spectroscopy. Different fungicide types produce unique electronic aroma signature...

  5. Thermal Conductivity of Gas Mixtures in Chemical Equilibrium

    Science.gov (United States)

    Brokaw, Richard S.

    1960-01-01

    The expression for the thermal conductivity of gas mixtures in chemical equilibrium is presented in a simpler and less restrictive form. This new form is shown to be equivalent to the previous equations.

  6. Study of Residual Gas Analyser (RGA) Response towards Known Leaks

    International Nuclear Information System (INIS)

    Pathan, Firozkhan S; Khan, Ziauddin; Semwal, Pratibha; George, Siju; Raval, Dilip C; Thankey, Prashant L; Manthena, Himabindu; Yuvakiran, Paravastu; Dhanani, Kalpesh R

    2012-01-01

    Helium leak testing is the most versatile form of weld qualification test for any vacuum application. Almost every ultra-high vacuum (UHV) system utilizes this technique for insuring leak tightness for the weld joints as well as demountable joints. During UHV system under operational condition with many other integrated components, in-situ developed leaks identification becomes one of the prime aspect for maintaining the health of such system and for continuing the experiments onwards. Since online utilization of leak detector (LD) has many practical limitations, residual gas analyser (RGA) can be used as a potential instrument for online leak detection. For this purpose, a co-relation for a given leak rate between Leak Detector and RGA is experimentally established. This paper describes the experimental aspect and the relationship between leak detector and RGA.

  7. RESIDUAL-GAS-IONIZATION BEAM PROFILE MONITORS IN RHIC.

    Energy Technology Data Exchange (ETDEWEB)

    CONNOLLY, R.; MICHNOFF, R.; TEPIKIAN, S.

    2005-05-16

    Four ionization profile monitors (IPMs) in RHIC measure vertical and horizontal beam profiles in the two rings by measuring the distribution of electrons produced by beam ionization of residual gas. During the last three years both the collection accuracy and signal/noise ratio have been improved. An electron source is mounted across the beam pipe from the collector to monitor microchannel plate (MCP) aging and the signal electrons are gated to reduce MCP aging and to allow charge replenishment between single-turn measurements. Software changes permit simultaneous measurements of any number of individual bunches in the ring. This has been used to measure emittance growth rates on six bunches of varying intensities in a single store. Also the software supports FFT analysis of turn-by-turn profiles of a single bunch at injection to detect dipole and quadrupole oscillations.

  8. The emission of fluorine gas during incineration of fluoroborate residue

    Energy Technology Data Exchange (ETDEWEB)

    Feng, Yuheng, E-mail: fengyh@tongji.edu.cn [Thermal & Environmental Engineering Institute, Tongji University, Shanghai 200092 (China); Jiang, Xuguang [State Key Laboratory of Clean Energy Utilization, Zhejiang University, Hangzhou 310027 (China); Chen, Dezhen [Thermal & Environmental Engineering Institute, Tongji University, Shanghai 200092 (China)

    2016-05-05

    Highlights: • Gaseous fluorine products were identified when combusting fluoroborate residue. • BF{sub 3} and SiF{sub 4} tend to be hydrolyzed into HF with the increase of temperature. • The emission of BF{sub 3} and SiF{sub 4} from the chamber could be negligible at 1100 °C. - Abstract: The emission behaviors of wastes from fluorine chemical industry during incineration have raised concerns because multiple fluorine products might danger human health. In this study, fluorine emission from a two-stage incineration system during the combustion of fluoroborate residue was examined. In a TG-FTIR analysis BF{sub 3}, SiF{sub 4} and HF were identified as the initial fluorine forms to be released, while fluorine gases of greenhouse effect such as CF{sub 4} and SF{sub 6} were not found. Below 700 °C, NaBF{sub 4} in the sample decomposed to generate BF{sub 3}. Then part of BF{sub 3} reacted with SiO{sub 2} in the system to form SiF{sub 4} or hydrolyzed to HF. At higher temperatures, the NaF left in the sample was gradually hydrolyzed to form HF. A lab-scale two-stage tube furnace is established to simulate the typical two-stage combustion chamber in China. Experimental tests proved that HF was the only fluorine gas in the flue gas, and emissions of BF{sub 3} and SiF{sub 4} can be negligible. Thermodynamic equilibrium model predicted that all SiF{sub 4} would be hydrolyzed at 1100 °C in the secondary-chamber, which agreed well with the experimental results.

  9. Conductivity modeling of gas sensors based on copper ...

    African Journals Online (AJOL)

    The main objective of this work is to study the electronic conductivity of copper phthalocyanine (CuPc) thin films in presence of certain strong oxidizing gases involved in air pollution, particularly NO2, for use as gas sensor devices. To achieve this objective, the first part presents a study of the conductivity evolution of these ...

  10. Electrical Conductive Mechanism of Gas Hydrate-Bearing Reservoirs in the Permafrost Region of Qilian Mountain

    Science.gov (United States)

    Peng, C.; Zou, C.; Tang, Y.; Liu, A.; Hu, X.

    2017-12-01

    In the Qilian Mountain, gas hydrates not only occur in pore spaces of sandstones, but also fill in fractures of mudstones. This leads to the difficulty in identification and evaluation of gas hydrate reservoir from resistivity and velocity logs. Understanding electrical conductive mechanism is the basis for log interpretation. However, the research is insufficient in this area. We have collected well logs from 30 wells in this area. Well logs and rock samples from DK-9, DK-11 and DK-12 wells were used in this study. The experiments including SEM, thin section, NMR, XRD, synthesis of gas hydrate in consolidated rock cores under low temperature and measurement of their resistivity and others were performed for understanding the effects of pore structure, rock composition, temperature and gas hydrate on conductivity. The results show that the porosity of reservoir of pore filling type is less than 10% and its clay mineral content is high. As good conductive passages, fractures can reduce resistivity of water-saturated rock. If fractures in the mudstone are filled by calcite, resistivity increases significantly. The resistivity of water-saturated rock at 2°C is twice of that at 18°C. The gas hydrate formation process in the sandstone was studied by resistivity recorded in real time. In the early stage of gas hydrate formation, the increase of residual water salinity may lead to the decrease of resistivity. In the late stage of gas hydrate formation, the continuity decrease of water leads to continuity increase of resistivity. In summary, fractures, rock composition, temperature and gas hydrate are important factors influencing resistivity of formation. This study is helpful for more accurate evaluation of gas hydrate from resistivity log. Acknowledgment: We acknowledge the financial support of the National Special Program for Gas Hydrate Exploration and Test-production (GZH201400302).

  11. Injection, flow, and mixing of CO2 in porous media with residual gas.

    Energy Technology Data Exchange (ETDEWEB)

    Oldenburg, C.M.; Doughty, C.A.

    2010-09-01

    Geologic structures associated with depleted natural gas reservoirs are desirable targets for geologic carbon sequestration (GCS) as evidenced by numerous pilot and industrial-scale GCS projects in these environments world-wide. One feature of these GCS targets that may affect injection is the presence of residual CH{sub 4}. It is well known that CH{sub 4} drastically alters supercritical CO{sub 2} density and viscosity. Furthermore, residual gas of any kind affects the relative permeability of the liquid and gas phases, with relative permeability of the gas phase strongly dependent on the time-history of imbibition or drainage, i.e., dependent on hysteretic relative permeability. In this study, the effects of residual CH{sub 4} on supercritical CO{sub 2} injection were investigated by numerical simulation in an idealized one-dimensional system under three scenarios: (1) with no residual gas; (2) with residual supercritical CO{sub 2}; and (3) with residual CH{sub 4}. We further compare results of simulations that use non-hysteretic and hysteretic relative permeability functions. The primary effect of residual gas is to decrease injectivity by decreasing liquid-phase relative permeability. Secondary effects arise from injected gas effectively incorporating residual gas and thereby extending the mobile gas plume relative to cases with no residual gas. Third-order effects arise from gas mixing and associated compositional effects on density that effectively create a larger plume per unit mass. Non-hysteretic models of relative permeability can be used to approximate some parts of the behavior of the system, but fully hysteretic formulations are needed to accurately model the entire system.

  12. Origins of the residual pulse height deficit in propane-filled gas ionization detectors

    International Nuclear Information System (INIS)

    Weijers-Dall, T.D.M.; Timmers, H.; Elliman, R.G.

    2005-01-01

    This work investigates the origins of the residual pulse height deficit in gas ionization detectors. It is motivated by the recent observation that the species dependence of gas detector response cannot be accounted for solely by considering the energy loss of the ions in the detector window and non-ionizing energy loss processes in the detector gas. It was found that the residual pulse height deficit is approximately proportional to the square of the ionization density. However, only a weak dependence of the residual deficit on gas pressure (in the range 70-120mbar) was observed. It is hypothesized that the residual pulse height deficit in gas ionization detectors results from the effect of multiple ionization of individual gas molecules at high ionization densities on the energy required to create an electron-ion pair

  13. Conductivity modeling of gas sensors based on copper ...

    African Journals Online (AJOL)

    On the lower side of the substrate, a screen-printed platinum resistor is devoted to sensor temperature control (Fig. 1). Interdigitated Pt electrodes (IDEs), polarized under 1 volt dc, are used to measure conductivity variations of the CuPc thin film which depend, in time, of gas concentration in sensor environment [26].

  14. Electrical Resistivity Survey For Conductive Soils At Gas Turbine ...

    African Journals Online (AJOL)

    Ten (10) vertical electrical soundings (VES) using Schlumberger configuration were carried out to delineate subsurface conductive soils for the design of earthling grid for electrical materials installation at the Gas Turbine Station, Ajaokuta, SW Nigeria. Interpretation of the resistivity data revealed three major geoelectric ...

  15. Study of residual gas adsorption on GaN nanowire arrays photocathode

    Energy Technology Data Exchange (ETDEWEB)

    Xia, Sihao; Liu, Lei, E-mail: liu1133_cn@sina.com.cn; Diao, Yu; Kong, Yike

    2017-05-01

    Highlights: • H{sub 2}O is more easily to absorb on the nanowire surface. • The work function increase after residual gas adsorption. • Bandgaps of the nanowire increase slightly. • Absorption coefficient is reduced and moves to higher energy side. - Abstract: In order to find out the influences of residual gas on GaN nanowire arrays photocathode, the optoelectronic properties of adsorption system are calculated on the basis of first principles. Results suggest that the residual gas adsorption will increase the work function and introduce a dipole moment with a direction from the nanowire to the adsorbates. The surface structures are changed and electrons transfer from nanowire to gas molecule. The bandgaps are enhanced after adsorption. Besides, the peak of absorption coefficients is reduced and moves to higher energy side. It is discovered that residual gas will drastically degrade the characteristics and lifetime of GaN nanowire arrays photocathode.

  16. Development of microstrip gas chambers on substrata with electronic conductivity

    International Nuclear Information System (INIS)

    Bouclier, R.; Garabatos, C.; Manzin, G.; Sauli, F.; Shekhtman, L.; Temmel, T.; Della Mea, G.; Maggioni, G.; Rigato, V.; Logachenko, I.

    1994-01-01

    This paper describes several recent developments on Microstrip Gas Chambers (MSGCs). The authors have studied the operating behavior of the detectors in different gas mixtures; maximum stable gains have been achieved in mixtures of argon and dimethyl-ether (DME) in almost equal proportions. Using detectors manufactured on semi-conducting glass substrates, capable of withstanding very high rates (above 10 6 mm -2 s -1 ), they have demonstrated extended lifetime without gain modifications up to a collected charge of 130 mC cm -1 in clean laboratory operating conditions. They have also verified that relaxing the requirements on cleanness conditions, either in the gas mixing system or in the detector construction, may result in fast aging of the devices under irradiation. As an alternative to the semi-conducting glass, they have developed a novel technique to coat regular glass with a thin lead silicate layer having electron conductivity; a new development consisting in coating already manufactured MSGCs with the thin semi-conducting layer is also described. The preliminary results show an excellent rate capability of this kind of devices, intrinsically simpler to manufacture

  17. DSMC Convergence for Microscale Gas-Phase Heat Conduction

    Science.gov (United States)

    Rader, D. J.; Gallis, M. A.; Torczynski, J. R.

    2004-11-01

    The convergence of Bird's Direct Simulation Monte Carlo (DSMC) method is investigated for gas-phase heat conduction at typical microscale conditions. A hard-sphere gas is confined between two fully accommodating walls of unequal temperature. Simulations are performed for small system and local Knudsen numbers, so continuum flow exists outside the Knudsen layers. The ratio of the DSMC thermal conductivity to the Chapman-Enskog value in the central region is determined for over 200 combinations of time step, cell size, and number of computational molecules per cell. In the limit of vanishing error, this ratio approaches 1.000 to within the correlation uncertainty. In the limit of infinite computational molecules per cell, the difference from unity depends quadratically on time step and cell size as these quantities become small. The coefficients of these quadratic terms are in good agreement with Green-Kubo values found by Hadjiconstantinou, Garcia, and co-workers. These results demonstrate that DSMC can accurately simulate microscale gas-phase heat conduction. Sandia is a multiprogram laboratory operated by Sandia Corporation, a Lockheed Martin Company, for the United States Department of Energy's National Nuclear Security Administration under contract DE-AC04-94AL85000.

  18. On residual gas analysis during high temperature baking of graphite tiles

    International Nuclear Information System (INIS)

    Prakash, A A; Chaudhuri, P; Khirwadkar, S; Reddy, D Chenna; Saxena, Y C; Chauhan, N; Raole, P M

    2008-01-01

    Steady-state Super-conducting Tokamak-1 (SST-1) is a medium size tokamak with major radius of 1.1 m and minor radius of 0.20 m. It is designed for plasma discharge duration of 1000 seconds to obtain fully steady-state plasma operation. Plasma Facing Components (PFC), consisting of divertors, passive stabilizers, baffles and poloidal limiters are also designed to be UHV compatible for steady state operation. All PFC are made up of graphite tiles mechanically attached to the copper alloy substrate. Graphite is one of the preferred first wall armour material in present day tokamaks. High thermal shock resistance and low atomic number of carbon are the most important properties of graphite for this application. High temperature vacuum baking of graphite tiles is the standard process to remove the impurities. Residual Gas Analyzer (RGA) has been used for qualitative and quantitative measurements of released gases from graphite tiles during baking. Surface Analysis of graphite tiles has also been done before and after baking. This paper describes the residual gas analysis during baking and surface analysis of graphite tiles

  19. On residual gas analysis during high temperature baking of graphite tiles

    Science.gov (United States)

    Prakash, A. A.; Chaudhuri, P.; Khirwadkar, S.; Chauhan, N.; Raole, P. M.; Reddy, D. Chenna; Saxena, Y. C.

    2008-05-01

    Steady-state Super-conducting Tokamak-1 (SST-1) is a medium size tokamak with major radius of 1.1 m and minor radius of 0.20 m. It is designed for plasma discharge duration of 1000 seconds to obtain fully steady-state plasma operation. Plasma Facing Components (PFC), consisting of divertors, passive stabilizers, baffles and poloidal limiters are also designed to be UHV compatible for steady state operation. All PFC are made up of graphite tiles mechanically attached to the copper alloy substrate. Graphite is one of the preferred first wall armour material in present day tokamaks. High thermal shock resistance and low atomic number of carbon are the most important properties of graphite for this application. High temperature vacuum baking of graphite tiles is the standard process to remove the impurities. Residual Gas Analyzer (RGA) has been used for qualitative and quantitative measurements of released gases from graphite tiles during baking. Surface Analysis of graphite tiles has also been done before and after baking. This paper describes the residual gas analysis during baking and surface analysis of graphite tiles.

  20. Gas composition of sludge residue profiles in a sludge treatment reed bed between loadings

    DEFF Research Database (Denmark)

    Larsen, Julie Dam; Nielsen, Steen M; Scheutz, Charlotte

    2017-01-01

    Treatment of sludge in sludge treatment reed bed systems includes dewatering and mineralization. The mineralization process, which is driven by microorganisms, produces different gas species as by-products. The pore space composition of the gas species provides useful information on the biological...... processes occurring in the sludge residue. In this study, we measured the change in composition of gas species in the pore space at different depth levels in vertical sludge residue profiles during a resting period of 32 days. The gas composition of the pore space in the sludge residue changed during...... the resting period. As the resting period proceeded, atmospheric air re-entered the pore space at all depth levels. The methane (CH4) concentration was at its highest during the first part of the resting period, and then declined as the sludge residue became more dewatered and thereby aerated. In the pore...

  1. Thermal conductivity of aerogel blanket insulation under cryogenic-vacuum conditions in different gas environments

    Science.gov (United States)

    E Fesmire, J.; Ancipink, J. B.; Swanger, A. M.; White, S.; Yarbrough, D.

    2017-12-01

    Thermal conductivity of low-density materials in thermal insulation systems varies dramatically with the environment: cold vacuum pressure, residual gas composition, and boundary temperatures. Using a reference material of aerogel composite blanket (reinforcement fibers surrounded by silica aerogel), an experimental basis for the physical heat transmission model of aerogel composites and other low-density, porous materials is suggested. Cryogenic-vacuum testing between the boundary temperatures of 78 K and 293 K is performed using a one meter cylindrical, absolute heat flow calorimeter with an aerogel blanket specimen exposed to different gas environments of nitrogen, helium, argon, or CO2. Cold vacuum pressures include the full range from 1×10-5 torr to 760 torr. The soft vacuum region, from about 0.1 torr to 10 torr, is complex and difficult to model because all modes of heat transfer - solid conduction, radiation, gas conduction, and convection - are significant contributors to the total heat flow. Therefore, the soft vacuum tests are emphasized for both heat transfer analysis and practical thermal data. Results for the aerogel composite blanket are analyzed and compared to data for its component materials. With the new thermal conductivity data, future applications of aerogel-based insulation systems are also surveyed. These include Mars exploration and surface systems in the 5 torr CO2 environment, field joints for vacuum-jacketed cryogenic piping systems, common bulkhead panels for cryogenic tanks on space launch vehicles, and liquid hydrogen cryofuel systems with helium purged conduits or enclosures.

  2. Determination of organophosphorus pesticide residues in tomatoes by gas chromatography

    International Nuclear Information System (INIS)

    Souissi, Sihem

    2010-01-01

    Chloropyriphos and malathion are two organophosphorus pesticides from many others pesticides widely used by famers in agriculture .Because of their bad effect on human health, officials standards are set by the international organisations and communities to ensure safer food for consumer .In the same way, scientists over the world are working hard to develop new detection techniques responding to the international requirements. In this study, an ' IAEA-ethylacetate method ', an adaptation of the popular QuEChERS multi residue method, was optimized to analyse chloropyriphos and Malathion residues in tomatoes .Ethyl-Acetate was used as an extraction solvent the PSA was kept for the clean up procedure. GC-NPD is used for samples analysis .The method optimized is specifique, selective with a recovery averaged more than 70 pour cent. A complete validation of the method is necessary to be used for routine analysis.

  3. Residual lifetime assessment of uPVC gas pipes

    OpenAIRE

    Visser, HA

    2010-01-01

    The Dutch gas distribution network consists of about 20% (22,500 km) of unplasticised poly(vinyl chloride) (uPVC) pipes, most of which have been installed from the mid-sixties up to the mid-seventies of the previous century and have been in service ever since. Replacing the uPVC gas pipes exactly after the specified service lifetime of 50 years will lead to a costly and extremely labour intensive project in the next decade. Postponing the replacement is only an option when it can be done with...

  4. Changes in entrapped gas content and hydraulic conductivity with pressure.

    Science.gov (United States)

    Marinas, Maricris; Roy, James W; Smith, James E

    2013-01-01

    Water table fluctuations continuously introduce entrapped air bubbles into the otherwise saturated capillary fringe and groundwater zone, which reduces the effective (quasi-saturated) hydraulic conductivity, K(quasi), thus impacting groundwater flow, aquifer recharge and solute and contaminant transport. These entrapped gases will be susceptible to compression or expansion with changes in water pressure, as would be expected with water table (and barometric pressure) fluctuations. Here we undertake laboratory experiments using sand-packed columns to quantify the effect of water table changes of up to 250 cm on the entrapped gas content and the quasi-saturated hydraulic conductivity, and discuss our ability to account for these mechanisms in ground water models. Initial entrapped air contents ranged between 0.080 and 0.158, with a corresponding K(quasi) ranging between 2 and 6 times lower compared to the K(s) value. The application of 250 cm of water pressure caused an 18% to 26% reduction in the entrapped air content, resulting in an increase in K(quasi) by 1.16 to 1.57 times compared to its initial (0 cm water pressure) value. The change in entrapped air content measured at pressure step intervals of 50 cm, was essentially linear, and could be modeled according to the ideal gas law. Meanwhile, the changes in K(quasi) with compression-expansion of the bubbles because of pressure changes could be adequately captured with several current hydraulic conductivity models. © Ground Water 2012 and © Her Majesty the Queen in Right of Canada 2012. Ground Water © 2012, National Ground Water Association.

  5. Procedure of Active Residual Heat Removal after Emergency Shutdown of High-Temperature-Gas-Cooled Reactor

    Directory of Open Access Journals (Sweden)

    Xingtuan Yang

    2014-01-01

    Full Text Available After emergency shutdown of high-temperature-gas-cooled reactor, the residual heat of the reactor core should be removed. As the natural circulation process spends too long period of time to be utilized, an active residual heat removal procedure is needed, which makes use of steam generator and start-up loop. During this procedure, the structure of steam generator may suffer cold/heat shock because of the sudden load of coolant or hot helium at the first few minutes. Transient analysis was carried out based on a one-dimensional mathematical model for steam generator and steam pipe of start-up loop to achieve safety and reliability. The results show that steam generator should be discharged and precooled; otherwise, boiling will arise and introduce a cold shock to the boiling tubes and tube sheet when coolant began to circulate prior to the helium. Additionally, in avoiding heat shock caused by the sudden load of helium, the helium circulation should be restricted to start with an extreme low flow rate; meanwhile, the coolant of steam generator (water should have flow rate as large as possible. Finally, a four-step procedure with precooling process of steam generator was recommended; sensitive study for the main parameters was conducted.

  6. Conductive component after cochlear implantation in patients with residual hearing conservation.

    Science.gov (United States)

    Chole, Richard A; Hullar, Timothy E; Potts, Lisa G

    2014-12-01

    Changes in auditory thresholds following cochlear implantation are generally assumed to be due to damage to neural elements. Theoretical studies have suggested that placement of a cochlear implant can cause a conductive hearing loss. Identification of a conductive component following cochlear implantation could guide improvements in surgical techniques or device designs. The purpose of this study is to characterize new-onset conductive hearing losses after cochlear implantation. In a prospective study, air- and bone-conduction audiometric testing were completed on cochlear implant recipients. An air-bone gap equal to or greater than 15 dB HL at 2 frequencies determined the presence of a conductive component. Of the 32 patients with preoperative bone-conduction hearing, 4 patients had a new-onset conductive component resulting in a mixed hearing loss, with air-conduction thresholds ranging from moderate to profound and an average air-bone gap of 30 dB HL. One had been implanted through the round window, 2 had an extended round window, and 1 had a separate cochleostomy. Loss of residual hearing following cochlear implantation may be due in part to a conductive component. Identifying the mechanism for this conductive component may help minimize hearing loss. Postoperative hearing evaluation should measure both air- and bone-conduction thresholds.

  7. Characteristics of gas and residues produced from electric arc pyrolysis of waste lubricating oil.

    Science.gov (United States)

    Song, Geum-Ju; Seo, Yong-Chil; Pudasainee, Deepak; Kim, In-Tae

    2010-07-01

    An attempt has been made to recover high-calorific fuel gas and useful carbonaceous residue by the electric arc pyrolysis of waste lubricating oil. The characteristics of gas and residues produced from electric arc pyrolysis of waste lubricating oil were investigated in this study. The produced gas was mainly composed of hydrogen (35-40%), acetylene (13-20%), ethylene (3-4%) and other hydrocarbons, whereas the concentration of CO was very low. Calorific values of gas ranged from 11,000 to 13,000 kcal kg(-1) and the concentrations of toxic gases, such as NO(x), HCl and HF, were below the regulatory emissions limit. Gas chromatography-mass spectrometry (GC/MS) analysis of liquid-phase residues showed that high molecular-weight hydrocarbons in waste lubricating oil were pyrolyzed into low molecular-weight hydrocarbons and hydrogen. Dehydrogenation was found to be the main pyrolysis mechanism due to the high reaction temperature induced by electric arc. The average particle size of soot as carbonaceous residue was about 10 microm. The carbon content and heavy metals in soot were above 60% and below 0.01 ppm, respectively. The utilization of soot as industrial material resources such as carbon black seems to be feasible after refining and grinding. Copyright (c) 2009 Elsevier Ltd. All rights reserved.

  8. Conductive polymer nanowire gas sensor fabricated by nanoscale soft lithography

    Science.gov (United States)

    Tang, Ning; Jiang, Yang; Qu, Hemi; Duan, Xuexin

    2017-12-01

    Resistive devices composed of one-dimensional nanostructures are promising candidates for the next generation of gas sensors. However, the large-scale fabrication of nanowires is still challenging, which restricts the commercialization of such devices. Here, we report a highly efficient and facile approach to fabricating poly(3,4-ethylenedioxythiophene)-poly(styrenesulfonate) (PEDOT:PSS) nanowire chemiresistive gas sensors by nanoscale soft lithography. Well-defined sub-100 nm nanowires are fabricated on silicon substrate, which facilitates device integration. The nanowire chemiresistive gas sensor is demonstrated for NH3 and NO2 detection at room temperature and shows a limit of detection at ppb level, which is compatible with nanoscale PEDOT:PSS gas sensors fabricated with the conventional lithography technique. In comparison with PEDOT:PSS thin-film gas sensors, the nanowire gas sensor exhibits higher sensitivity and a much faster response to gas molecules.

  9. The effects of rape residue mulching on net global warming potential and greenhouse gas intensity from no-tillage paddy fields.

    Science.gov (United States)

    Zhang, Zhi-Sheng; Cao, Cou-Gui; Guo, Li-Jin; Li, Cheng-Fang

    2014-01-01

    A field experiment was conducted to provide a complete greenhouse gas (GHG) accounting for global warming potential (GWP), net GWP, and greenhouse gas intensity (GHGI) from no-tillage (NT) paddy fields with different amounts of oilseed rape residue mulch (0, 3000, 4000, and 6000 kg dry matter (DM) ha(-1)) during a rice-growing season after 3 years of oilseed rape-rice cultivation. Residue mulching treatments showed significantly more organic carbon (C) density for the 0-20 cm soil layer at harvesting than no residue treatment. During a rice-growing season, residue mulching treatments sequestered significantly more organic C from 687 kg C ha(-1) season(-1) to 1654 kg C ha(-1) season(-1) than no residue treatment. Residue mulching significantly increased emissions of CO2 and N2O but decreased CH4 emissions. Residue mulching treatments significantly increased GWP by 9-30% but significantly decreased net GWP by 33-71% and GHGI by 35-72% relative to no residue treatment. These results suggest that agricultural economic viability and GHG mitigation can be achieved simultaneously by residue mulching on NT paddy fields in central China.

  10. The Effects of Rape Residue Mulching on Net Global Warming Potential and Greenhouse Gas Intensity from No-Tillage Paddy Fields

    Science.gov (United States)

    Zhang, Zhi-Sheng; Cao, Cou-Gui; Guo, Li-Jin; Li, Cheng-Fang

    2014-01-01

    A field experiment was conducted to provide a complete greenhouse gas (GHG) accounting for global warming potential (GWP), net GWP, and greenhouse gas intensity (GHGI) from no-tillage (NT) paddy fields with different amounts of oilseed rape residue mulch (0, 3000, 4000, and 6000 kg dry matter (DM) ha−1) during a rice-growing season after 3 years of oilseed rape-rice cultivation. Residue mulching treatments showed significantly more organic carbon (C) density for the 0–20 cm soil layer at harvesting than no residue treatment. During a rice-growing season, residue mulching treatments sequestered significantly more organic C from 687 kg C ha−1 season−1 to 1654 kg C ha−1 season−1 than no residue treatment. Residue mulching significantly increased emissions of CO2 and N2O but decreased CH4 emissions. Residue mulching treatments significantly increased GWP by 9–30% but significantly decreased net GWP by 33–71% and GHGI by 35–72% relative to no residue treatment. These results suggest that agricultural economic viability and GHG mitigation can be achieved simultaneously by residue mulching on NT paddy fields in central China. PMID:25140329

  11. Gas chromatographic determination of pesticide residues in white mustard.

    Science.gov (United States)

    Słowik-Borowiec, Magdalena; Szpyrka, Ewa; Walorczyk, Stanisław

    2015-04-15

    A new analytical method employing gas chromatography coupled to electron capture and nitrogen phosphorus detection (GC-ECD/NPD) has been developed and validated for the screening and quantification of 51 pesticides in a matrix of high chlorophyll content - white mustard (Sinapis alba L.). For preparation of the sample extract, the citrate buffered QuEChERS procedure was followed. However certain changes were made to adapt the method to our needs and available laboratory resources. The sample size was reduced to 5 g, 10 mL water was added and exchange of solvent before GC analysis was done. The samples spiked with the target pesticides at the concentration level 0.01 mg/kg and a higher level (depending on the compound) yielded average recoveries in the range of 70-120% with relative standard deviations (RSDs) 0-19% except for HCB, S-metolachlor and teflubenzuron, and displayed very good linearity (R(2)>0.99) for nearly all the analytes. Limit of quantification was 0.01 mg/kg for the majority of the analytes. The expanded measurement uncertainties were estimated employing a "top-down" empirical model as being between 6% and 32% and yielding an average value of 18% (coverage factor k=2, confidence level 95%). Copyright © 2014 Elsevier Ltd. All rights reserved.

  12. Validation of a methodology multi-residue for the determination of pesticides residuals in strawberry (fragraria spp.) by gas chromatography

    International Nuclear Information System (INIS)

    Montano Garces, Mauricio; Guerrero Dallos, Jairo Arturo

    2001-01-01

    This study describes the validation of multi-residue analytical methodology for the simultaneous determination of 19 organ chlorine, organophosphorus and organ nitrogen pesticides in strawberry. Pesticides residues were extracted from strawberry samples with ethyl acetate, the extracts were cleaned-up by GPC, the quantitative analysis was carried out by high resolution gas chromatography (GC) with a pulsed splitless injection mode and simultaneous detection by m-ECD and NPD coupled in parallel. The methodology is specific, selective, and accurate and robust the calibration curves in matrix matched analytical standards show linearity over the concentration range of 0.04-5.00 mg/kg with limits of detection and quantitation between 0.007-0.5 mg/kg and 0.01-1.00 mg/kg respectively. The recovery experiments yielding averages between 80-110% for most of the pesticides. The distribution of analyze in the laboratory sample was evaluated and it was found its homogeneity. The methodology was applied in field samples and was mainly found Captan residues below MRL

  13. Effect of flue gas desulfurization residue on plant establishment and soil and leachate quality

    Energy Technology Data Exchange (ETDEWEB)

    Punshon, T.; Adriano, D.C.; Weber, J.T. [University of Georgia, Savannah, GA (USA). Savannah River Ecology Lab.

    2001-06-01

    Effects on soil quality and crop establishment after incorporation of flue gas desulfurization by-product (FGD) into soil as an amendment was assessed in a mesocosm study. Mesocosm units received applications equivalent to 0, 2.5, 5.0, 7.5 and 10% FGD residue. Germination, biomass production, and elemental composition of corn, radish and cotton were determined. The quality of leachates and soil were also determined periodically. Flue gas desulfurization residue did not affect germination and all application rates stimulated aboveground biomass. Plants grown in FGD-amended soil contained significantly elevated tissue concentrations of As, B, Se, and Mo. The FGD residue elevated surface soil pH from 5.5 to 8.1. Leachate pH was unaffected by FGD, but salinity rose sharply with increasing application rates of FGD. Leachates contained higher concentrations of B, with small increases in Se and As. Flue gas desulfurization residue application caused an increase in total B, As, Mo, Se and extractable Ca in the soil, but decreased Mn and Zn. Using FGD residues could have beneficial effects on crop establishment without detrimental effects on soil or leachate quality, at an optimum rate of approximately 2.5%. This material could alleviate surface acidity, and B and Mo deficiencies in plants. 27 refs., 6 figs., 4 tabs.

  14. Residual radioactive contamination of the Maralinga range from nuclear weapons tests conducted in 1956 and 1957

    International Nuclear Information System (INIS)

    Cooper, M.B.; Duggleby, J.C.; Kotler, L.H.; Wise, K.N.

    1978-12-01

    Detailed geographical distributions and concentrations of long-lived radionuclides remaining from the major trials of nuclear weapons conducted at Maralinga in 1956 and 1957 are presented. It is shown that residual contamination due to fission products - mainly strontium-90, caesium-137 and europium-155 - are well below levels that could constitute a health hazard to occupants of the area. In the regions near the ground zeroes however, long-lived neutron activation products in soil - mainly cobalt-60 and europium-152 - are present in sufficient abundance to give rise to gamma-radiation dose-rates up to 2 milliroentgen per hour, which exceed maximum recommended dose-rates for continuous occupancy

  15. Analysis of residual swirl in tangentially-fired natural gas-boiler

    International Nuclear Information System (INIS)

    Hasril Hasini; Muhammad Azlan Muad; Mohd Zamri Yusoff; Norshah Hafeez Shuaib

    2010-01-01

    This paper describes the investigation on residual swirl flow in a 120 MW natural gas, full-scale, tangential-fired boiler. Emphasis is given towards the understanding of the behavior of the combustion gas flow pattern and temperature distribution as a result of the tangential firing system of the boiler. The analysis was carried out based on three-dimensional computational modeling on full scale boiler with validation from key design parameter as well as practical observation. Actual operating parameters of the actual boiler are taken as the boundary conditions for this modeling. The prediction of total heat flux was found to be in agreement with the key design parameter while the residual swirl predicted at the upper furnace agrees qualitatively with the practical observation. Based on this comparison, detail analysis was carried out for comprehensive understanding on the generation and destruction of the residual swirl behavior in boiler especially those with high capacity. (author)

  16. Radiation and gas conduction heat transport across a helium dewar multilayer insulation system

    International Nuclear Information System (INIS)

    Green, M.A.

    1994-01-01

    This report describes a method for calculating mixed heat transfer through the multilayer insulation used to insulate a 4 K liquid helium cryostat. The method described here permits one to estimate the insulation potential for a multilayer insulation system from first principles. The heat transfer regimes included are: radiation, conduction by free molecule gas conduction, and conduction through continuum gas conduction. Heat transfer in the transition region between the two gas conduction regimes is also included

  17. Application of Conductive Carbon Nanotube Fibers and Composites: Gas Sensor

    Science.gov (United States)

    2013-05-01

    interfering vapors such as hexane by using a 2-micron thick barrier film of chemical-selective polymer polyiobutylene ( PIB ) on the SWNT surface...Gas Resistance -- (57) 2006 Kyle DMMP, DIMP SWNT PET, PIB Gas Resistance 299 ppm (21) 2005 Choi DMMP, DPGME, DCM -- Al2O3, In2O3, Pt, Pd, ZnO

  18. Near-Surface Residual Stress-Profiling with High Frequency Eddy Current Conductivity Measurement

    Science.gov (United States)

    Hillmann, S.; Heuer, H.; Baron, H.-U.; Bamberg, J.; Yashan, A.; Meyendorf, N.

    2009-03-01

    The lifetime of aero engine components can be extended by applying an additional strain to the material. Typical aero engine-alloys like Nickel-Base superalloys or Titanium alloys can be surface-treated by use of shot peening to induce the compressive strain near the surface. However, in order to use the additional life for critical aero engine components, a quantitative determination of strain gradients near the surface has to be carried out periodically. We propose to measure the depth-profile of residual stresses non-destructively by use of high frequency eddy current techniques. This paper presents results obtained with an experimental set-up based on a high precision impedance analyzer. Test samples prepared from IN718 by shot peening of different intensities can be easily distinguished. By sweeping the frequency from 100 kHz up to 100 MHz a depth profile for the electrical conductivity from 50 μm to 500 μm can be obtained. The measured conductivity profile is a resultant from residual stresses, cold work, surface roughness and the texture of the material. In addition, first results for strain profiling obtained with industry applicable NDE instrument will be presented.

  19. Comparison of thin layer chromatographic and gas chromatographic determination of propoxur residues in a cocoa ecosystem

    International Nuclear Information System (INIS)

    Yeboah, P.O.; Lowor, S.; Akpabli, C.K.

    2005-01-01

    The fate of propoxur in a cocoa ecosystem has been studied using thin layer chromatographic (TLC) and gas chromatographic (GC) methods. Residues of propoxur as determined by both TLC and GC were not significantly different. TLC analysis of propoxur residues in soil, cocoa leaves and pods did not require any rigorous cleanup since residues measured from cleaned extracts and without cleanup were not significantly different. The residue levels of propoxur in the soil were found to decrease rapidly and, by the 21st day, none was detected in the topsoil (0-15 cm). Evidence of leaching of propoxur residues in the soil has also been demonstrated. The amount left in the top soil after the first seven days were 27%, 23% and 24% of the initial one as determined by the TLC without cleanup, TLC with cleanup and GLC, respectively. No propoxur residue was detected in topsoil 21 days after spraying. About 38% of pesticides detected on the cocoa pod on the day of treatment remained on the pod seven days after treatment. The residue detected on the leaves on the day of treatment was higher than that in or on the soil. This decreased rapidly to 1.7% in 21 days compared to 16% for the soil and 23% for the pod. (author)

  20. Controlling residual hydrogen gas in mass spectra during pulsed laser atom probe tomography.

    Science.gov (United States)

    Kolli, R Prakash

    2017-01-01

    Residual hydrogen (H 2 ) gas in the analysis chamber of an atom probe instrument limits the ability to measure H concentration in metals and alloys. Measuring H concentration would permit quantification of important physical phenomena, such as hydrogen embrittlement, corrosion, hydrogen trapping, and grain boundary segregation. Increased insight into the behavior of residual H 2 gas on the specimen tip surface in atom probe instruments could help reduce these limitations. The influence of user-selected experimental parameters on the field adsorption and desorption of residual H 2 gas on nominally pure copper (Cu) was studied during ultraviolet pulsed laser atom probe tomography. The results indicate that the total residual hydrogen concentration, H TOT , in the mass spectra exhibits a generally decreasing trend with increasing laser pulse energy and increasing laser pulse frequency. Second-order interaction effects are also important. The pulse energy has the greatest influence on the quantity H TOT , which is consistently less than 0.1 at.% at a value of 80 pJ.

  1. Determination of Profenofos Pesticidal Residue in Lettuce (Lactuca sativa L. by Gas Chromatographic Method

    Directory of Open Access Journals (Sweden)

    Yohannes Alen

    2015-05-01

    Full Text Available The determination of profenofos pesticidal residue in the lettuce (Lactuca sativa L. by using gas chromatography using flame photometric detector (FPD had been investigated. The lettuce was collected from Padang Luar area, Agam distric, West Sumatera. Sample for determination of profenofos residue divided into three groups: unwashed (A, washed with water (B, and washed with detergent (C. Maceration with sonication was used for the extraction using ethylacetateas a solvent. The results showed that profenofos pesticide residue in sample A, B and C were 0.204, 0.080 and 0.061 ppm, respectively. These profenofos pesticidal residue are over than the Maximum Residue Limits (MRL that established by The Japan Food Chemical Research Foundation (0.05 ppm even though World Health Organization (WHO has not established Maximum Residue Limits (MRL profenofos on lettuce. Based on the statistical analysis one-way method (Anova using SPSS 20.0 showed that there was a significant concentrations difference between lettuce A from lettuce B and lettuce C with p < 0.05.

  2. Analytical model for thermal boundary conductance and equilibrium thermal accommodation coefficient at solid/gas interfaces.

    Science.gov (United States)

    Giri, Ashutosh; Hopkins, Patrick E

    2016-02-28

    We develop an analytical model for the thermal boundary conductance between a solid and a gas. By considering the thermal fluxes in the solid and the gas, we describe the transmission of energy across the solid/gas interface with diffuse mismatch theory. From the predicted thermal boundary conductances across solid/gas interfaces, the equilibrium thermal accommodation coefficient is determined and compared to predictions from molecular dynamics simulations on the model solid-gas systems. We show that our model is applicable for modeling the thermal accommodation of gases on solid surfaces at non-cryogenic temperatures and relatively strong solid-gas interactions (ε(sf) ≳ k(B)T).

  3. Assessment of pesticide residues in some fruits using gas chromatography coupled with micro electron capture detector

    International Nuclear Information System (INIS)

    Latif, Y.; Sherazi, S.T.H.; Bhanger, M.I.

    2011-01-01

    A very sensitive analytical method for the determination of 26 pesticides in some fruits based on solid phase extraction (SPE) cleanup was developed using gas chromatography (GC) coupled with micro electron capture detector (mu ECD). The identity of the pesticides was confirmed by gas chromatography mass spectroscopy (GC-MS) using selected ion monitoring (SIM) mode. Ethyl acetate was used as a solvent for the extraction of pesticide residues with assistance of sonication. For cleanup an octadecyl, C18 SPE column was used. A linear response of mu ECD was observed for all pesticides with good correlation coefficients (>0.9992). Proposed method was successfully applied for the determination of pesticide residues in the orange, apple, and grape fruits. Average recoveries achieved for all of the pesticides at fortification levels of 0.05, 1.0 and 2.0 mu g g/sup -1/ in analyzed fruits were above 90% with relative standard deviations (RSD) less than 6%. (author)

  4. Residual entropy and waterlike anomalies in the repulsive one dimensional lattice gas

    Energy Technology Data Exchange (ETDEWEB)

    Silva, Fernando Barbosa V. da [Instituto de Física, Universidade de Brasília, Brasília-DF (Brazil); Instituto Federal de Brasília, Campus São Sebastião, São Sebastião-DF (Brazil); Oliveira, Fernando Albuquerque, E-mail: fao@fis.unb.br [Instituto de Física, Universidade de Brasília, Brasília-DF (Brazil); Barbosa, Marco Aurélio A., E-mail: aureliobarbosa@gmail.com [Programa de Pós-Graduação em Ciência de Materiais, Faculdade UnB Planaltina, Universidade de Brasília, Planaltina-DF (Brazil)

    2015-04-14

    The thermodynamics and kinetics of the one dimensional lattice gas with repulsive interaction are investigated using transfer matrix technique and Monte Carlo simulations. This simple model is shown to exhibit waterlike anomalies in density, thermal expansion coefficient, and self-diffusion. An unified description for the thermodynamic anomalies in this model is achieved based on the ground state residual entropy which appears in the model due to mixing entropy in a ground state phase transition.

  5. Identification and discrimination of herbicide residues using a conducting polymer electronic nose

    Science.gov (United States)

    Alphus Dan Wilson

    2016-01-01

    The identification of herbicide residues on crop foliage is necessary to make crop-management decisions for weed pest control and to monitor pesticide residue levels on food crops. Electronic-nose (e-nose) methods were tested as a cheaper, alternative means of discriminating between herbicide residue types (compared with conventional chromatography methods), by...

  6. Residual Gas and Dust around Transition Objects and Weak T Tauri Stars

    Energy Technology Data Exchange (ETDEWEB)

    Doppmann, Greg W. [W. M. Keck Observatory, 65-1120 Mamalahoa Hwy., Kamuela, HI 96743 (United States); Najita, Joan R. [National Optical Astronomy Observatory, 950 N. Cherry Avenue, Tucson, AZ 85719 (United States); Carr, John S., E-mail: gdoppmann@keck.hawaii.edu, E-mail: najita@noao.edu, E-mail: carr@nrl.navy.mil [Naval Research Laboratory, Code 7213, Washington, DC 20375 (United States)

    2017-02-20

    Residual gas in disks around young stars can spin down stars, circularize the orbits of terrestrial planets, and whisk away the dusty debris that is expected to serve as a signpost of terrestrial planet formation. We have carried out a sensitive search for residual gas and dust in the terrestrial planet region surrounding young stars ranging in age from a few to ∼10 Myr. Using high-resolution 4.7 μ m spectra of transition objects (TOs) and weak T Tauri stars, we searched for weak continuum excesses and CO fundamental emission, after making a careful correction for the stellar contribution to the observed spectrum. We find that the CO emission from TOs is weaker and located farther from the star than CO emission from nontransition T Tauri stars with similar stellar accretion rates. The difference is possibly the result of chemical and/or dynamical effects (i.e., a low CO abundance or close-in low-mass planets). The weak T Tauri stars show no CO fundamental emission down to low flux levels (5 × 10{sup −20} to 10{sup −18} W m{sup −2}). We illustrate how our results can be used to constrain the residual disk gas content in these systems and discuss their potential implications for star and planet formation.

  7. Effect of Residual Gas Composition on Epitaxial Growth of Graphene on SiC

    Science.gov (United States)

    Kunc, J.; Rejhon, M.; Belas, E.; Dědič, V.; Moravec, P.; Franc, J.

    2017-10-01

    In recent years, graphene growth optimization has been one of the key routes towards large-scale, high-quality graphene production. We measure in situ residual gas content during epitaxial-graphene growth on silicon carbide (SiC) to find detrimental factors of epitaxial-graphene growth. The growth conditions in high vacuum, in argon, purified argon, and the flow of argon are compared. The grown epitaxial graphene is studied by Raman-scattering mapping. We determine mechanical strain, number of graphene layers and the graphene quality. The surface topography is measured by atomic force microscopy. Charge density and carrier mobility are studied by Hall-effect measurements in van der Pauw configuration. We identify the major role of the chemical reaction of carbon and residual water. The rate of the reaction is lowered when purified argon is used. We also show that, according to time-varying gas content, it is preferable to grow graphene at higher temperatures and shorter times. Other sources of growth environment contamination are also discussed. The reaction of residual gas and SiC is discussed as one of the factors decreasing the lateral size of SiC atomically flat terraces and leading to their irregular shape. The importance of purified argon and its sufficient flow rate is concluded to be important for high-quality graphene growth as it reduces the rate of undesired chemical reactions and provides a more stable and defined growth ambient.

  8. A stochastic logical system approach to model and optimal control of cyclic variation of residual gas fraction in combustion engines

    International Nuclear Information System (INIS)

    Wu, Yuhu; Kumar, Madan; Shen, Tielong

    2016-01-01

    Highlights: • An in-cylinder pressure based measuring method for the RGF is derived. • A stochastic logical dynamical model is proposed to represent the transient behavior of the RGF. • The receding horizon controller is designed to reduce the variance of the RGF. • The effectiveness of the proposed model and control approach is validated by the experimental evidence. - Abstract: In four stroke internal combustion engines, residual gas from the previous cycle is an important factor influencing the combustion quality of the current cycle, and the residual gas fraction (RGF) is a popular index to monitor the influence of residual gas. This paper investigates the cycle-to-cycle transient behavior of the RGF in the view of systems theory and proposes a multi-valued logic-based control strategy for attenuation of RGF fluctuation. First, an in-cylinder pressure sensor-based method for measuring the RGF is provided by following the physics of the in-cylinder transient state of four-stroke internal combustion engines. Then, the stochastic property of the RGF is examined based on statistical data obtained by conducting experiments on a full-scale gasoline engine test bench. Based on the observation of the examination, a stochastic logical transient model is proposed to represent the cycle-to-cycle transient behavior of the RGF, and with the model an optimal feedback control law, which targets on rejection of the RGF fluctuation, is derived in the framework of stochastic logical system theory. Finally, experimental results are demonstrated to show the effectiveness of the proposed model and the control strategy.

  9. [Simultaneous determination of seven residual solvents in bovis calculus artifactus by headspace gas chromatography].

    Science.gov (United States)

    Chi, Shuyao; Wu, Dike; Sun, Jinhong; Ye, Ruhan; Wang, Xiaoyan

    2014-05-01

    A headspace gas chromatography (HS-GC) method was developed for the simultaneous determination of seven residual solvents (petroleum ether (60-90 degrees C), acetone, ethyl acetate, methanol, methylene chloride, ethanol and butyl acetate) in bovis calculus artifactus. The DB-WAX capillary column and flame ionization detector (FID) were used for the separation and detection of the residual solvents, and the internal standard method was used for the quantification. The chromatographic conditions, such as equilibrium temperature and equilibrium time, were optimized. Under the optimized conditions, all of the seven residual solvents showed good linear relationships with good correlation coefficients (not less than 0.999 3) in the prescribed concentration range. At three spiked levels, the recoveries for the seven residual solvents were 94.7%-105.2% with the relative standard deviations (RSDs) less than 3.5%. The limits of detection (LODs) of the method were 0.43-5.23 mg/L, and the limits of quantification (LOQs) were 1.25-16.67 mg/L. The method is simple, rapid, sensitive and accurate, and is suitable for the simultaneous determination of the seven residual solvents in bovis calculus artifactus.

  10. Analysis of residual toluene in food packaging via headspace extraction method using gas chromatography

    International Nuclear Information System (INIS)

    Lim, Ying Chin; Mohd Marsin Sanagi

    2008-01-01

    Polymeric materials are used in many food contact applications as packaging material. The presence of residual toluene in this food packaging material can migrate into food and thus affect the quality of food. In this study, a manual headspace analysis was successfully designed and developed. The determination of residual toluene was carried out with standard addition method and multiple headspace extraction, MHE) method using gas chromatography-flame ionization detector, GC-FID). Identification of toluene was performed by comparison of its retention time with standard toluene and GC-MS. It was found that the suitable heating temperature was 180 degree Celsius with an optimum heating time of 10 minutes. The study also found that the concentration of residual toluene in multicolored sample was higher compared to mono colored sample whereas residual toluene in sample analyzed using standard addition method was higher compared to MHE method. However, comparison with the results obtained from De Paris laboratory, France found that MHE method gave higher accuracy for sample with low analyte concentration. On the other hand, lower accuracy was obtained for sample with high concentration of residual toluene due to systematic errors. Comparison between determination methods showed that MHE method is more precise compared to standard addition method. (author)

  11. Evaluation of residue management practices effects on corn productivity, soil quality, and greenhouse gas emissions

    Science.gov (United States)

    Guzman, Jose German

    The removal of crop residues left after harvest is being considered as a potential feedstock source for bioethanol production which can contribute to the reduction of fossil fuel use and net greenhouse gas (GHG). The objectives of this study were to: (i) examine how tillage, N fertilization rates, residue removal, and their interactions affect crop productivity, (ii) SOC and soil physical properties, and (iii) GHG emissions, and (iv) calculated a soil C budget to determine how much crop residue can be sustainably be removed in Central and Southwest Iowa. After three years of residue removal under different management practices, the findings of this study suggest that a portion of the corn residue that is left on the soil surface after harvest can be removed, with no negative impacts in the short term continuous corn yield in sites at Central and Southwest Iowa. However, significant decreases in SOC sequestration rates, microbial biomass-C, bulk density, soil penetration resistance, wet aggregate stability, and infiltration rates were observed, but varied with soil type and management practices. Additionally, soil surface CO2 and N2O emissions were responsive to management practices; primarily by altering soil temperature, soil water content, soil mineral N, and crop growth. Results from soil C budget show that in 2010 when corn growth was not water stressed (lack of moisture), approximately 35 and 30% of the residue could be sustainably removed in the Central and Southwest sites, respectively. In 2011, drier soil conditions resulted in approximately 2 and 49% of the residue could be sustainably removed in the Central and Southwest sites, respectively.

  12. Multiscale development of a fission gas thermal conductivity model: Coupling atomic, meso and continuum level simulations

    Science.gov (United States)

    Tonks, Michael R.; Millett, Paul C.; Nerikar, Pankaj; Du, Shiyu; Andersson, David; Stanek, Christopher R.; Gaston, Derek; Andrs, David; Williamson, Richard

    2013-09-01

    Fission gas production and evolution significantly impact the fuel performance, causing swelling, a reduction in the thermal conductivity and fission gas release. However, typical empirical models of fuel properties treat each of these effects separately and uncoupled. Here, we couple a fission gas release model to a model of the impact of fission gas on the fuel thermal conductivity. To quantify the specific impact of grain boundary (GB) bubbles on the thermal conductivity, we use atomistic and mesoscale simulations. Atomistic molecular dynamic simulations were employed to determine the GB thermal resistance. These values were then used in mesoscale heat conduction simulations to develop a mechanistic expression for the effective GB thermal resistance of a GB containing gas bubbles, as a function of the percentage of the GB covered by fission gas. The coupled fission gas release and thermal conductivity model was implemented in Idaho National Laboratory's BISON fuel performance code to model the behavior of a 10-pellet LWR fuel rodlet, showing how the fission gas impacts the UO2 thermal conductivity. Furthermore, additional BISON simulations were conducted to demonstrate the impact of average grain size on both the fuel thermal conductivity and the fission gas release.

  13. Multiscale development of a fission gas thermal conductivity model: Coupling atomic, meso and continuum level simulations

    International Nuclear Information System (INIS)

    Tonks, Michael R.; Millett, Paul C.; Nerikar, Pankaj; Du, Shiyu; Andersson, David; Stanek, Christopher R.; Gaston, Derek; Andrs, David; Williamson, Richard

    2013-01-01

    Fission gas production and evolution significantly impact the fuel performance, causing swelling, a reduction in the thermal conductivity and fission gas release. However, typical empirical models of fuel properties treat each of these effects separately and uncoupled. Here, we couple a fission gas release model to a model of the impact of fission gas on the fuel thermal conductivity. To quantify the specific impact of grain boundary (GB) bubbles on the thermal conductivity, we use atomistic and mesoscale simulations. Atomistic molecular dynamic simulations were employed to determine the GB thermal resistance. These values were then used in mesoscale heat conduction simulations to develop a mechanistic expression for the effective GB thermal resistance of a GB containing gas bubbles, as a function of the percentage of the GB covered by fission gas. The coupled fission gas release and thermal conductivity model was implemented in Idaho National Laboratory’s BISON fuel performance code to model the behavior of a 10-pellet LWR fuel rodlet, showing how the fission gas impacts the UO 2 thermal conductivity. Furthermore, additional BISON simulations were conducted to demonstrate the impact of average grain size on both the fuel thermal conductivity and the fission gas release

  14. Thermal conductivity of gas by pulse injection techniques using specific thermal conductivity detector (TCD)

    OpenAIRE

    Cataluña, Renato; Silva, Rosângela da; Menezes, Eliana W.; Samios, Dimitrios

    2004-01-01

    This paper presents a procedure to determine the thermal conductivity of gases by pulse injection, using a thermal conductivity detector (TCD). The measurements are taken at 323K and atmospheric pressure with a 160 omega tungsten filament sensor. Under well defined approximations the original nonlinear second order equation, which describes the sensors output, as a function of thermal conductivity and constant volume specific heat was transformed into a linear first order equation. According ...

  15. Determination of insecticides malathion and lambda-cyhalothrin residues in zucchini by gas chromatography

    Directory of Open Access Journals (Sweden)

    Hayam M. Lofty

    2013-12-01

    Full Text Available A sensitive gas chromatographic method has been developed for the determination of malathion and lambda-cyhalothrin (λ-cyhalothrin insecticide residues in zucchini. The developed method consists of extraction with acetone, purification and partitioning with methylene chloride, column chromatographic clean-up, and finally capillary gas chromatographic determination of the insecticides. The recoveries of method were greater than 90% and limit of determination was 0.001 ppm for both insecticides. The method was applied to determine residues and the rate of disappearance of malathion and λ-cyhalothrin from fruits of zucchini (open field treatment, 50 cc of Malason/Cormandel 57% EC (emulsifiable concentrate for 100 L of water, 20 cc of LAMBDA SUPER FOG 5% liquid for 100 L of water. The insecticide incorporated into the plants decreased rapidly with a half-life time around 0.77 day (18.5h for malathion and 4 days for λ-cyhalothrin. It is not recommended to use zucchini before 12 h of malathion application. For λ-cyhalothrin, the preharvest interval is 5 days. Four market samples were chosen from different regions from A.R.E. and all of them showed no residues of malathion or λ-cyhalothrin.

  16. Alternative Gas Mixtures in Arc Spraying: A Chance to Improve Coating Properties and Residual Stress States

    Science.gov (United States)

    Hauer, Michél; Henkel, Knuth Michael; Krebs, Sebastian; Kroemmer, Werner

    2018-01-01

    The highly cavitation erosion-resistant propeller alloys CuAl9Ni5Fe4Mn (Ni-Al-Bronze) and CuMn13Al8Fe3Ni2 (Mn-Al-Bronze) were arc-sprayed using a mixture of nitrogen and 2% of hydrogen as atomizing gas and different traverse speeds. The objective was to identify the influences of the different spraying conditions, such as temperature regime and melting loss, on the resulting residual stress states and coating properties. Residual stresses were measured by the incremental hole-drilling method using ESPI. Temperature measurements were carried out by thermographic imaging. Microstructural, chemical and mechanical analyses were realized to examine adhesive and cohesive properties. Additionally, the cavitation erosion behavior was investigated to analyze cohesive coating properties. The spraying process itself was improved, which was apparent by mainly enhanced deposition efficiency and reduced surface temperatures. The amount of oxides and pores as well as the melting loss of alloying elements were reduced. Moreover, an increased cavitation erosion resistance and thus coating cohesion as well as less residual stresses were identified. The change in atomizing gas diminished the impact of the quenching stresses on the coating properties. In contrast, the adhesive strength, Young's moduli and partially the hardness were slightly reduced. With regard to materials, Ni-Al-Bronze revealed superior coating properties in comparison with Mn-Al-Bronze.

  17. Technical assessment of synthetic natural gas (SNG) production from agriculture residuals

    Science.gov (United States)

    Song, Guohui; Feng, Fei; Xiao, Jun; Shen, Laihong

    2013-08-01

    This paper presents thermodynamic evaluations of the agriculture residual-to-SNG process by thermochemical conversion, which mainly consists of the interconnected fluidized beds, hot gas cleaning, fluidized bed methanation reactor and Selexol absorption unit. The process was modeled using Aspen Plus software. The process performances, i.e., CH4 content in SNG, higher heating value and yield of SNG, exergy efficiencies with and without heat recovery, unit power consumption, were evaluated firstly. The results indicate that when the other parameters remain unchanged, the steam-to-biomass ratio at carbon boundary point is the optimal value for the process. Improving the preheating temperatures of air and gasifying agent is beneficial for the SNG yield and exergy efficiencies. Due to the effects of CO2 removal efficiency, there are two optimization objectives for the SNG production process: (I) to maximize CH4 content in SNG, or (II) to maximize SNG yield. Further, the comparison among different feedstocks indicates that the decreasing order of SNG yield is: corn stalk > wheat straw > rice straw. The evaluation on the potential of agriculture-based SNG shows that the potential annual production of agriculture residual-based SNG could be between 555×108 ˜ 611×108 m3 with utilization of 100% of the available unexplored resources. The agriculture residual-based SNG could play a significant role on solving the big shortfall of China's natural gas supply in future.

  18. Identification of insecticide residues with a conducting-polymer electronic nose

    Science.gov (United States)

    A.D. Wilson

    2014-01-01

    The identification of insecticide residues on crop foliage is needed to make periodic pest management decisions. Electronic-nose (e-nose) methods were developed and tested as a means of acquiring rapid identifications of insecticide residue types at relatively low cost by detection of headspace volatiles released from inert surfaces in vitro. Detection methods were...

  19. Thermal Conductivity of ZIF-8 Thin-Film under Ambient Gas Pressure.

    Science.gov (United States)

    Cui, Boya; Audu, Cornelius O; Liao, Yijun; Nguyen, SonBinh T; Farha, Omar K; Hupp, Joseph T; Grayson, Matthew

    2017-08-30

    Thermal conductivity is a crucial parameter for managing exothermal gas adsorption in metal organic frameworks (MOFs), but experimental studies have been limited. In this work, the thermal conductivity of a zeolitic imidazolate framework ZIF-8 was experimentally determined on thin films using the 3ω technique at different partial pressures in perfluorohexane, nitrogen, air, and vacuum ambients at 300 K. In contrast to theoretical prediction, the thermal conductivity κ = 0.326 ± 0.002 W/m K was approximately independent of ambient gas species and pressure from atmospheric pressure to vacuum. This work introduces a useful approach for probing MOF thermal conductivity under gas adsorption.

  20. Comparison of Postoperative Pain and Residual Gas Between Restrictive and Liberal Fluid Therapy in Patients Undergoing Laparoscopic Cholecystectomy.

    Science.gov (United States)

    Yao, Lei; Wang, Yulan; Du, Boxiang; Song, Jie; Ji, Fuhai

    2017-10-01

    Different fluid regimens are used in the clinical management of perioperative fluid therapy, but there still is the argument about which fluid regimen is better for patients. This study was mainly designed to compare different fluid regimens on postoperative pain and residual gas in patients undergoing laparoscopic cholecystectomy. A total of 100 patients were equally randomized to receive restrictive fluid infusion (n=50) with lactated Ringer (LR) solution 5 mL/kg/h or liberal fluid infusion (n=50), with 30 mL/kg/h lactated Ringer solution. Postoperative pain was evaluated at 1, 6, and 24 hours after surgery using a visual analog scale (VAS). Postoperative subdiaphragmatic residual gas was monitored by x-ray at 24 hours after surgery. Patients in the restrictive group had significantly higher VAS pain scores at 6 hours after surgery than those in the liberal group (P=0.009). The incidence of subdiaphragmatic residual gas in the restrictive group was higher than in the liberal group (P=0.045). Patients who had residual gas had higher VAS pain scores than those with no residual gas in the restrictive group at 6 hours after surgery (P=0.02). Patients undergoing laparoscopic cholecystectomy with restrictive fluid therapy may suffer more severe postoperative pain than those receiving liberal fluid therapy. It suggests that the higher incidence of subdiaphragmatic residual gas may have occurred with restrictive fluid therapy.

  1. A Simple and Rapid Extraction for Gas Chromatographic Determination of Thiabendazole and Imazalil Residues in Lemons

    Directory of Open Access Journals (Sweden)

    Navickiene Sandro

    2002-01-01

    Full Text Available A rapid and efficient method is described for the determination of thiabendazole and imazalil residues in lemons (peel and pulp. The procedure is based on the extraction with an hexane:ethyl acetate mixture (1:1, v/v and gas chromatographic analysis using thermionic specific detection (TSD. The possibility of matrix effect was also studied. Mean recoveries from 8 replicates of fortified samples ranged from 79% to 109%, with relative standard deviation values between 2.4% to 12.8%. The detection and quantification limits of the method were 0.2 mg kg-1 and 0.5 mg kg-1, respectively.

  2. Analysis of Petroleum Products in Fire Debris Residues by Gas Chromatography: A Literature Review

    Directory of Open Access Journals (Sweden)

    Gurvinder Singh Bumbrah

    2017-06-01

    Full Text Available This review gives a brief overview of developments in the analysis of petroleum products (PP in fire debris residues (FDR by gas chromatography (GC. The review covers different aspects of analysis such as the substrates involved, isolation procedures, column and mobile phase used, and subsequent detection in tabular form. This paper covers detection of PP such as petrol, kerosene, and diesel in various types’ of samples of interest to fire debris analysts. Solid phase microextraction is most frequently used along with gas chromatography-mass spectrometry (GC-MS for the extraction and identification of PP from FDR. Chemometric tools should be used to improve the significance and reliability of results obtained from the analysis of FDR. However, the potential utility of portable GC-MS in fire debris analysis cannot be ignored, and its proper development and validation is required before using it for this purpose.

  3. Disposition of transuranic residues from plutonium isentropic compression experiment (Pu-ice) conducted at Z machine

    Energy Technology Data Exchange (ETDEWEB)

    Goyal, Kapil K [Los Alamos National Laboratory; French, David M [Los Alamos National Laboratory; Humphrey, Betty J [WESTON SOLUTIONS INC.; Gluth, Jeffry [SNL

    2010-01-01

    In 1992, the U.S. Congress passed legislation to discontinue above- and below-ground testing of nuclear weapons. Because of this, the U.S. Department of Energy (DOE) must rely on laboratory experiments and computer-based calculations to verify the reliability of the nation's nuclear stockpile. The Sandia National Laboratories/New Mexico (SNL/NM) Z machine was developed by the DOE to support its science-based approach to stockpile stewardship. SNL/NM researchers also use the Z machine to test radiation effects on various materials in experiments designed to mimic nuclear explosions. Numerous components, parts, and materials have been tested. These experiments use a variety of radionuclides; however, plutonium (Pu) isotopes with greater than ninety-eight percent enrichment are the primary radionuclides used in the experiments designed for stockpile stewardship. In May 2006, SNL/NM received authority that the Z Machine Isentropic Compression Experiments could commence. Los Alamos National Laboratory (LANL) provided the plutonium targets and loaded the target assemblies, which were fabricated by SNL/NM. LANL shipped the loaded assemblies to SNL/NM for Z machine experiments. Three experiments were conducted from May through July 2006. The residues from each experiment, which weighed up to 913 pounds, were metallic and packaged into a respective 55-gallon drum each. Based on a memorandum of understanding between the two laboratories, LANL provides the plutonium samples and the respective radio-isotopic information. SNL/NM conducts the experiments and provides temporary storage for the drums until shipment to LANL for final waste certification for disposal at the Waste Isolation Pilot Plant (WIPP) in southeastern New Mexico. This paper presents a comprehensive approach for documenting generator knowledge for characterization of waste in cooperation with scientists at the two laboratories and addresses a variety of topics such as material control and accountability

  4. Study of radiolytic effect on residual ethylene oxide in perfusion devices for single use by using gas chromatography

    International Nuclear Information System (INIS)

    Wang Mingsuo; Teng Weifang; Liu Keliang; Feng Jixin; Su Liaoyuan

    1993-01-01

    The efficiency of the 60 Co γ-rays irradiation induced elimination reaction of residual ethylene oxide (RETO) in the perfusion devices for single use conducted with RETO gas chromatography has been studied. The observations show: 1. the splinting reaction of RETO absorbed by the infusion sets after ethylene oxide (ETO) sterilization occurred accompanied with 4 kGy irradiation, therefore the relative elimination percentage (RELP) calculated from RETO is over 90%. 2. the optimum radiation conditions are as following irradiation dose 4 kGy, dose rate 8 Gy/min, irradiation temperature 20 degree C. 3. the RETO content within medical infusion sets at 2 weeks storing time after radiation was probably controlled under 2.0 ppm. 4. the radiation chemistry mechanism of the RETO elimination reaction is discussed in relation to the primary and secondary actions of elimination reaction

  5. Laboratory-based validation of the baseline sensors of the ITER diagnostic residual gas analyzer

    Energy Technology Data Exchange (ETDEWEB)

    Biewer, Theodore M. [ORNL; Marcus, Chris [ORNL; Klepper, C Christopher [ORNL; Andrew, Philip [ITER Organization, Cadarache, France; Gardner, W. L. [United States ITER Project Office; Graves, Van B. [ORNL; Hughes, Shaun [ITER Organization, Saint Paul Lez Durance, France

    2017-10-01

    The divertor-specific ITER Diagnostic Residual Gas Analyzer (DRGA) will provide essential information relating to DT fusion plasma performance. This includes pulse-resolving measurements of the fuel isotopic mix reaching the pumping ducts, as well as the concentration of the helium generated as the ash of the fusion reaction. In the present baseline design, the cluster of sensors attached to this diagnostic's differentially pumped analysis chamber assembly includes a radiation compatible version of a commercial quadrupole mass spectrometer, as well as an optical gas analyzer using a plasma-based light excitation source. This paper reports on a laboratory study intended to validate the performance of this sensor cluster, with emphasis on the detection limit of the isotopic measurement. This validation study was carried out in a laboratory set-up that closely prototyped the analysis chamber assembly configuration of the baseline design. This includes an ITER-specific placement of the optical gas measurement downstream from the first turbine of the chamber's turbo-molecular pump to provide sufficient light emission while preserving the gas dynamics conditions that allow for \\textasciitilde 1 s response time from the sensor cluster [1].

  6. Laboratory-based validation of the baseline sensors of the ITER diagnostic residual gas analyzer

    Science.gov (United States)

    Klepper, C. C.; Biewer, T. M.; Marcus, C.; Andrew, P.; Gardner, W. L.; Graves, V. B.; Hughes, S.

    2017-10-01

    The divertor-specific ITER Diagnostic Residual Gas Analyzer (DRGA) will provide essential information relating to DT fusion plasma performance. This includes pulse-resolving measurements of the fuel isotopic mix reaching the pumping ducts, as well as the concentration of the helium generated as the ash of the fusion reaction. In the present baseline design, the cluster of sensors attached to this diagnostic's differentially pumped analysis chamber assembly includes a radiation compatible version of a commercial quadrupole mass spectrometer, as well as an optical gas analyzer using a plasma-based light excitation source. This paper reports on a laboratory study intended to validate the performance of this sensor cluster, with emphasis on the detection limit of the isotopic measurement. This validation study was carried out in a laboratory set-up that closely prototyped the analysis chamber assembly configuration of the baseline design. This includes an ITER-specific placement of the optical gas measurement downstream from the first turbine of the chamber's turbo-molecular pump to provide sufficient light emission while preserving the gas dynamics conditions that allow for \\textasciitilde 1 s response time from the sensor cluster [1].

  7. [Determination of residual toluene diisocyanate in sponge bra by gas chromatography].

    Science.gov (United States)

    Wang, Aixia; Ye, Ping; Huang, Nan; Chen, Yan; Li, Xinggen

    2017-06-08

    A gas chromatography (GC) with internal standard method was developed for the determination of residual toluene diisocyanate (TDI) in sponge bra. The samples were extracted with ethyl acetate dehydrated, and cleaned up with 0.22 μm microfiltration membrane. The residual toluene diisocyanate was separated on a DB-624 capillary column using temperature programming. The flame ionization detector (FID) was used at 250 ℃. The inlet temperature was 180 ℃ with nitrogen as carrier gas. The linear range was 10-200 mg/L ( R 2 =0.9989) for TDI. The average recovery ranged from 80.5% to 91.6% with RSD not more than 7.9%( n =6). The limit of detection (LOD) and limit of quantification (LOQ) were 10 mg/kg and 100 mg/kg, respectively. The developed method was then utilized to analyse the 100 batches of sponge bra samples from the manufacturing enterprises, the entity shops and electric business platforms. The method is simple, time-saving and environment friendly with high sensitivity and good reproducibility, and has practical application value due to its low-cost and short-circle.

  8. Assessment of Pesticide Residues in Some Fruits Using Gas Chromatography Coupled with Micro Electron Capture Detector

    Directory of Open Access Journals (Sweden)

    M. I. Bhanger

    2011-12-01

    Full Text Available A very sensitive analytical method for the determination of 26 pesticides in some fruits based on solid phase extraction (SPE cleanup was developed using gas chromatography (GC coupled with micro electron capture detector (μECD. The identity of the pesticides was confirmed by gas chromatography mass spectroscopy (GC-MS using selected ion monitoring (SIM mode. Ethyl acetate was used as a solvent for the extraction of pesticide residues with assistance of sonication. For cleanup an octadecyl, C18 SPE column was used. A linear response of μECD was observed for all pesticides with good correlation coefficients (>0.9992. Proposed method was successfully applied for the determination of pesticide residues in the orange, apple, and grape fruits. Average recoveries achieved for all of the pesticides at fortification levels of 0.05, 1.0 and 2.0 μg g-1 in analyzed fruits were above 90% with relative standard deviations (RSD less than 6

  9. Determination of residual dimethylsulphoxide in drug loaded gelatin using thermal desorber - gas chromatography.

    Science.gov (United States)

    Asfaw, Adissu Alemayehu; Wolfs, Kris; Van Schepdael, Ann; Adams, Erwin

    2018-05-10

    Traditional headspace - gas chromatography (HS-GC) methods for the determination of residual solvents (RS) start from a homogenous sample solution. Subsequently, it is challenging to determine RS using HS-GC techniques from insoluble solid samples like gelatin which is practically impossible to dissolve or distribute uniformly in water and common organic solvents. In this study, a thermal desorber combined with capillary gas chromatography and flame ionization detection/mass spectrometry (TD-GC-FID/MS) was used for quantitative determination of residual dimethylsulfoxide (DMSO) in gelatin without sample pretreatment. A sample of gelatin was sandwiched between two quartz filter double layers in a polytetrafluoroethylene insert which was then placed in its entirety into a thermal desorption tube. Factors affecting the performance of TD-GC including desorption time, desorption temperature, desorption flow and type of adsorbent were studied by applying a standard solution of DMSO in methanol on a blank gelatin bed. Validation results of the proposed method showed good linearity with an R 2 -value higher than 0.999 for a wide concentration range and good sensitivity with a limit of detection and limit of quantification of 0.1 μg and 0.2 μg on tube, respectively. The proposed method shows recovery values close to 100%. In addition, a conventional HS-GC method following enzymatic degradation of gelatin was developed to verify the proposed TD-GC method. Both methods were applied for the determination of residual DMSO in gelatin that was loaded with an experimental drug. Results were comparable, but the enzyme assisted HS-GC method was more time consuming and expensive. Copyright © 2018 Elsevier B.V. All rights reserved.

  10. Stabilizing effect of gas conductivity evolution on the resistive sausage mode of a propagating beam

    International Nuclear Information System (INIS)

    Lampe, M.; Joyce, G.

    1983-01-01

    Previous theoretical work has shown that a highly current-neutralized charged particle beam propagating in a preionized plasma channel of fixed conductivity is subject to a resistive sausage instability. It is shown that the instability is stabilized, for the case of beam propagation into an initially un-ionized gas, when the effect of beam-collisional ionization on the gas conductivity is modeled fully self-consistently

  11. Technology on In-Situ Gas Generation to Recover Residual Oil Reserves

    Energy Technology Data Exchange (ETDEWEB)

    Sayavur Bakhtiyarov

    2008-02-29

    This final technical report covers the period October 1, 1995 to February 29, 2008. This chapter begins with an overview of the history of Enhanced Oil Recovery techniques and specifically, CO2 flood. Subsequent chapters conform to the manner consistent with the Activities, Tasks, and Sub-tasks of the project as originally provided in Exhibit C1 in the Project Management Plan dated September 20, 1995. These chapters summarize the objectives, status and conclusions of the major project activities performed during the project period. The report concludes by describing technology transfer activities stemming from the project and providing a reference list of all publications of original research work generated by the project team or by others regarding this project. The overall objective of this project was a final research and development in the United States a technology that was developed at the Institute for Geology and Development of Fossil Fuels in Moscow, Russia. Before the technology can be convincingly adopted by United States oil and gas producers, the laboratory research was conducted at Mew Mexico Institute of Mining and Technology. The experimental studies were conducted to measure the volume and the pressure of the CO{sub 2} gas generated according to the new Russian technology. Two experimental devices were designed, built and used at New Mexico Tech facilities for these purposes. The designed setup allowed initiating and controlling the reaction between the 'gas-yielding' (GY) and 'gas-forming' (GF) agents proposed by Russian technology. The temperature was controlled, and the generated gas pressure and volume were recorded during the reaction process. Additionally, the effect of surfactant addition on the effectiveness of the process was studied. An alternative GY reactant was tested in order to increase the efficiency of the CO2 gas generation process. The slim tube and the core flood experimental studies were conducted to define

  12. Computer simulation of void formation in residual gas atom free metals by dual beam irradiation experiments

    International Nuclear Information System (INIS)

    Shimomura, Y.; Nishiguchi, R.; La Rubia, T.D. de; Guinan, M.W.

    1992-01-01

    In our recent experiments (1), we found that voids nucleate at vacancy clusters which trap gas atoms such as hydrogen and helium in ion- and neutron-irradiated copper. A molecular dynamics computer simulation, which implements an empirical embedded atom method to calculate forces that act on atoms in metals, suggests that a void nucleation occurs in pure copper at six and seven vacancy clusters. The structure of six and seven vacancy clusters in copper fluctuates between a stacking fault tetrahedron and a void. When a hydrogen is trapped at voids of six and seven vacancy, a void can keep their structure for appreciably long time; that is, the void do not relax to a stacking fault tetrahedron and grows to a large void. In order to explore the detailed atomics of void formation, it is emphasized that dual-beam irradiation experiments that utilize beams of gas atoms and self-ions should be carried out with residual gas atom free metal specimens. (author)

  13. Microstructural damage and residual mechanical properties in helium-bearing gas metal Arc weldments

    Science.gov (United States)

    Goods, S. H.; Yang, N. Y. C.

    1992-03-01

    The influence of entrapped helium on microstructural damage and residual mechanical properties subsequent to applying low-penetration gas metal arc (GMA) weld overlays was examined for an AISI Type 304 stainless steel. Two helium levels were examined: 22.5 and 85.0 atomic parts per million (appm) He. Detailed scanning electron microscopy (SEM) revealed the presence of intergranular cracks in the weld heat-affected zone (HAZ). The crack surfaces exhibited a dimple structure that was characteristic of a gas bubble embrittled material. Transmission electron microscopy (TEM) revealed that the size and spacing of the grain boundary helium gas bubbles remained virtually unchanged (relative to that established by the charging and aging procedure) at distances greater than 1 mm from the fusion line. Within this first millimeter, the diameter of the bubbles increased rapidly, and the bubble spacing increased to the characteristic spacing of the dimples that decorated weld-induced cracks. Mechanical testing revealed a loss in strain-to-fracture and ultimate tensile strength (UTS) at the higher helium level. While the majority of the fracture occurred in a transgranular, ductile manner, some deformation-induced intergranular cracking was observed. This cracking occurred over a very narrow region localized to the HAZ of the weldment. At the lower helium level, ductility and strength were unaffected compared to helium-free specimens.

  14. Oscillatory conductive heat transfer for a fiber in an ideal gas

    Science.gov (United States)

    Kuntz, H. L.; Perreira, N. D.

    1985-01-01

    A description of the thermal effects created by placing a cylindrical fiber in an inviscid, ideal gas, through which an acoustic wave propagates, is presented. The fibers and the gas have finite heat capacities and thermal conductivities. Expressions for the temperature distribution in the gas and in the material are determined. The temperature distribution is caused by pressure oscillations in the gas which, in turn, are caused by the passage of an acoustic wave. The relative value of a dimensionless parameter is found to be indicative of whether the exact or approximate equations should be used in the solution. This parameter is a function of the thermal conductivities and heat capacities of the fiber and gas, the acoustic frequency, and the fiber diameter.

  15. Electron space charge effects in ion sources for residual gas analysis

    International Nuclear Information System (INIS)

    Cowen, M.C.; Allison, W.

    1993-01-01

    An electron impact ionization source suitable for residual gas analysis (RGA) with a quadrupole mass spectrometer has been studied both experimentally and by computer simulation. The electronic space charge is shown to play a role in limiting the extracted current from RGA ion sources and the simulation treats this aspect of the problem self-consistently. Under certain source conditions, the ion extraction efficiency is observed to decrease for electron currents above approximately 1 mA - well below the current at which space charge limiting of the electron emission is expected. The observed effects are well reproduced by the simulation. We show that whereas the electron trajectories are only weakly perturbed by space charge effects, the loss of ionization efficiency can be attributed to drastic changes in the ion trajectories. (author)

  16. Pyrolysis of automotive shredder residue for the production of fuel-grade gas

    International Nuclear Information System (INIS)

    Sharp, L.L.; Ness, R.O. Jr.

    1993-01-01

    Every year eight to ten million cars and trucks are disposed of by shredding at one of the 200 auto shredders located in the United States. Automotive shredder residue (ASR) is a by-product created in the dismantling of automobiles. Figure 1 illustrates the process by which ASR is generated. An automobile is stripped of useful and/or hazardous items, such as the gas tank, battery, tires, and radiator. Although it is beneficial to have these items removed for safety and environmental concerns, this is not always accomplished. After removal of some or all of these items, the automobile is shredded to provide a material less than 4 inches in size and composed of approximately 50% organic and 50% inorganic fractions. Ferrous scrap is then separated out magnetically. This ferrous scrap supplies the steel industry with 12 to 14 million tons per year for electric arc furnace feedstock. Air cyclone separators isolate a low density open-quotes fluffclose quotes from the nonferrous fraction (aluminum, copper, etc.). This fluff (shredder residue) is composed of a variety of plastics, fabrics, foams, glass, rubber, and an assortment of contaminants. Fluff bulk density is approximately 20 lb/ft

  17. Equilibrium and nonequilibrium molecular dynamics simulations of thermal conductance at solid-gas interfaces.

    Science.gov (United States)

    Liang, Zhi; Evans, William; Keblinski, Pawel

    2013-02-01

    The thermal conductance at solid-gas interfaces with different interfacial bonding strengths is calculated through Green-Kubo equilibrium molecular dynamics (EMD) simulations. Due to the finite size of the simulation system, the long-time integral of the time correlation function of heat power across the solid-gas interface exhibits an exponential decay, which contains the information on interfacial thermal conductance. If an adsorbed gas layer is formed on the solid surface, it is found that the solid-gas interface needs to be defined at a plane outside the adsorbed layer so as to obtain the correct result from the Green-Kubo formula. The EMD simulation result agrees very well with that obtained from nonequilibrium molecular dynamics simulations. By calculating the average solid-gas interaction time as a function of solid-gas interaction strength, we find the incident gas atoms thermalize with the metal surface much more rapidly when the surface is covered by adsorbed gas molecules.

  18. Analysis of residual trifluoroacetic acid in a phosphate-buffered saline matrix by ion chromatography with suppressed conductivity detection.

    Science.gov (United States)

    Fernando, P N; McLean, M A; Egwu, I N; deGuzman, E; Weyker, C

    2001-06-22

    As part of the formulation of a cell-based pharmaceutical product, cells were harvested from mice and incubated in a cocktail containing cell culture media and high levels of trifluoroacetic acid (TFA). The cells were washed with a phosphate-buffered saline solution to remove residual cell culture media and other reagents before the cells were infused back into the mice from which they originated. Because of the potentially toxic nature of the TFA, the cells were washed multiple times and the final wash was monitored for residual TFA in order to demonstrate the efficient removal of the reagent before the cell product could be reintroduced into the test animal. This report describes the method that was developed incorporating anion-exchange chromatography with suppressed conductivity detection for the analysis of residual TFA (down to 50 ng/ml) in the presence of high concentrations of phosphate and chloride interferences. The ultimate sensitivity of the method was improved by selectively removing halide anions using a silver cartridge before sample analysis. The method proved to be rugged and reproducible enough to be validated and used to monitor residual TFA levels in cell washes in support of an acute toxicological study. Results demonstrating the method's sensitivity, selectivity, precision and linearity were reported.

  19. Analytical accuracy of hydrogen measurement using gas chromatography with thermal conductivity detection.

    Science.gov (United States)

    Weijun, Yao

    2015-08-01

    Gas chromatography employing a thermal conductivity detector with a nitrogen carrier gas and a molecular sieve 5 Å column is commonly used for the analysis of widely varying hydrogen concentrations. Flow variation of the column, caused by carrier gas adsorption, affects the peak shape and impacts the analytical accuracy. The mechanism and factors affecting the adsorption effect are explored, errors caused by the deviation from the linearity of the detector's response are considered, and practical advice is given for improving the analytical accuracy. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  20. Cobalt Doped SnO2 Thick Film Gas Sensors: Conductance and Gas Response Characteristics for LPG and CNG Gas

    OpenAIRE

    V. Kumar; S. K. Srivastava; Kiran Jain

    2009-01-01

    Cobalt doped thick films tin oxide sensors were studied for their LPG and CNG gas sensitivity. SnO2 powder was synthesized by precipitation technique and doped with cobalt sulphate (0 to 10 wt %) by impregnation technique. The sensing characteristics were found to depend on the cobalt concentration and operating temperature. Best performance for LPG and CNG detection was obtained for 3 wt % addition of cobalt sulphate. Cobalt doped SnO2 sensors showed a decrease in the optimum temperature for...

  1. Residual solvent determination by head space gas chromatography with flame ionization detector in omeprazole API

    Directory of Open Access Journals (Sweden)

    Saurabh Pandey

    2011-06-01

    Full Text Available Residual solvents in pharmaceutical samples are monitored using gas chromatography with head space. Based on good manufacturing practices, measuring residual solvents is mandatory for the release testing of all active pharmaceutical ingredients (API. The analysis of residual organic solvents (methanol, acetone, cyclohexane, dichloromethane, toluene in Omeprazole, an active pharmaceutical ingredient was investigated. Omeprazole is a potent reversible inhibitor of the gastric proton pump H+/K+-ATPase. The Head space gas chromatography (HSGC method described in this investigation utilized a SPB TM-624, Supelco, 30 m long x 0.25 mm internal diameter, 1.4µm-thick column. Since Omeprazole is a thermally labile compound, the selection of the proper injector temperature is critical to the success of the analysis. The injector temperature was set at 170ºC to prevent degradation. The initial oven temperature was set at 40ºC for 12 min and programmed at a rate of 10ºC min-1 to a final temperature of 220ºC for 5 min. Nitrogen was used as a carrier gas. The sample solvent selected was N,N-dimethylacetamide. The method was validated to be specific, linear, precise, sensitive, rugged and showed excellent recovery.Solventes residuais em amostras farmacêuticas são monitoradas utilizando-se cromatografia a gás "headspace". Com base nas boas práticas de fabricação, a medida de solventes residuais é obrigatória para o teste de liberação de todos os ingredientes farmacêuticos (API. Efetuou-se a análise de solventes orgânicos residuais (metanol, acetona, cicloexano, diclorometano, tolueno em omeprazol, ingrediente farmacêutico ativo. O omeprazol é potente inibidor reversível da bomba de prótons H+/K+-ATPase. A cromatografia a gás "headspace" (HSGC descrita nessa pesquisa utilizou um SPB TM-624, Supelco, de 30 m de comprimento x 0,25 mm de diâmetro interno, e coluna de 1,4 µm de espessura. Considerando-se que o omeprazol é termicamente l

  2. Electrical conduction and NO{sub 2} gas sensing properties of ZnO nanorods

    Energy Technology Data Exchange (ETDEWEB)

    Şahin, Yasin [Council of Forensic Medicine, Bahçelievler, 34196 Istanbul (Turkey); Öztürk, Sadullah, E-mail: sadullahozturk@gyte.edu.tr [Gebze Institute of Technology, Science Faculty, Department of Physics, 41400 Gebze, Kocaeli (Turkey); Kılınç, Necmettin [Gebze Institute of Technology, Science Faculty, Department of Physics, 41400 Gebze, Kocaeli (Turkey); Koc University, Department of Electrical and Electronics Engineering, Sariyer, 34450 Istanbul (Turkey); Kösemen, Arif [Gebze Institute of Technology, Science Faculty, Department of Physics, 41400 Gebze, Kocaeli (Turkey); Mus Alparslan University, Department of Physics, 49100 Mus (Turkey); Erkovan, Mustafa [SAKARYA University, Engineering Faculty, Department of Metallurgical and Materials Engineering, Esentepe Campus, 54187 Sakarya (Turkey); Öztürk, Zafer Ziya [Gebze Institute of Technology, Science Faculty, Department of Physics, 41400 Gebze, Kocaeli (Turkey); TÜBİTAK-Marmara Research Center, Materials Institute, 41470 Gebze, Kocaeli (Turkey)

    2014-06-01

    Thermally stimulated current (TSC), photoresponse and gas sensing properties of zinc oxide (ZnO) nanorods were investigated depending on heating rates, illumination and dark aging times with using sandwich type electrode system. Vertically aligned ZnO nanorods were grown on indium tin oxide (ITO) coated glass substrate by hydrothermal process. TSC measurements were performed at different heating rates under constant potential. Photoresponse and gas sensing properties were investigated in dry air ambient at 200 °C. For gas sensing measurements, ZnO nanorods were exposed to NO{sub 2} (100 ppb to 1 ppm) in dark and illuminated conditions and the resulting resistance transient was recorded. It was found from dark electrical measurements that the dependence of the dc conductivity on temperature followed Mott's variable range hopping (VRH) model. In addition, response time and recovery times of ZnO nanorods to NO{sub 2} gas decreased by exposing to white light.

  3. Conductive polymer gas sensor for quantitative detection of methanol in Brazilian sugar-cane spirit

    OpenAIRE

    Péres, Laura Oliveira [UNIFESP; Li, Rosamaria W. C.; Yamauchi, Elaine Y.; Lippi, Renata; Gruber, Jonas

    2012-01-01

    A low-cost chemiresistive gas sensor is described, made by the deposition of a thin film of a conductive polymer, poly(2-dodecanoylsulfanyl-p-phenylenevinylene), doped with dodecylbenzenesulfonic acid (10%, w/w), onto interdigitated electrodes. the sensor exhibits linear electrical conductance changes in function of the concentration of methanol present in sugar-cane spirit in the range between 0.05% and 4.0%. Since the sensor is cheap, easy to fabricate, durable, presents low power consumpti...

  4. Removal of element mercury by medicine residue derived biochars in presence of various gas compositions

    International Nuclear Information System (INIS)

    Li, Guoliang; Shen, Boxiong; Li, Yongwang; Zhao, Bin; Wang, Fumei; He, Chuan; Wang, Yinyin; Zhang, Min

    2015-01-01

    Highlights: • Both physisorption and chemisorption of Hg 0 occurred on the surface of M6WN5. • Chemisorption process was an absolute predominant route for Hg 0 removal by M6WN5. • The effect of NO, H 2 O, SO 2 and O 2 on Hg 0 removal by M6WN5 was investigated. • M6WN5 demonstrated to be a promising Hg 0 sorbent in flue gas. - Abstract: Pyrolyzed biochars from an industrial medicinal residue waste were modified by microwave activation and NH 4 Cl impregnation. Mercury adsorption of different modified biochars was investigated in a quartz fixed-bed reactor. The results indicated that both physisorption and chemisorption of Hg 0 occurred on the surface of M6WN5 which was modified both microwave and 5 wt.% NH 4 Cl loading, and exothermic chemisorption process was a dominant route for Hg 0 removal. Microwave activation improved pore properties and NH 4 Cl impregnation introduced good active sites for biochars. The presence of NO and O 2 increased Hg 0 adsorption whereas H 2 O inhibited Hg 0 adsorption greatly. A converse effect of SO 2 was observed on Hg 0 removal, namely, low concentration of SO 2 promoted Hg 0 removal obviously whereas high concentration of SO 2 suppressed Hg 0 removal. The Hg 0 removal by M6WN5 was mainly due to the reaction of the C−Cl with Hg 0 to form HgCl 2 , and the active state of C−Cl * groups might be an intermediate group in this process. Thermodynamic analysis showed that mercury adsorption by the biochars was exothermic process and apparent adsorption energy was 43.3 kJ/mol in the range of chemisorption. In spite of low specific surface area, M6WN5 proved to be a promising Hg 0 sorbent in flue gas when compared with other sorbents

  5. Tradeoffs between metabolic rate and spiracular conductance in discontinuous gas exchange of Samia cynthia (Lepidoptera, Saturniidae).

    Science.gov (United States)

    Moerbitz, Christian; Hetz, Stefan K

    2010-05-01

    The insect tracheal system is a unique respiratory system, designed for maximum oxygen delivery at high metabolic demands, e.g. during activity and at high ambient temperatures. Therefore, large safety margins are required for tracheal and spiracular conductance. Spiracles are the entry to the tracheal system and play an important role in controlling discontinuous gas exchange (DGC) between tracheal system and atmosphere in moth pupae. We investigated the effect of modulated metabolic rate (by changing ambient temperature) and modulated spiracular conductance (by blocking all except one spiracles) on gas exchange patterns in Samia pupae. Both, spiracle blocking and metabolic rates, affected respiratory behavior in Samia cynthia pupae. While animals showed discontinuous gas exchange cycles at lower temperatures with unblocked spiracles, the respiratory patterns were cyclic at higher temperatures, with partly blocked spiracles or a combination of these two factors. The threshold for the transition from a discontinuous (DGC) to a cyclic gas exchange ((cyc)GE) was significantly higher in animals with unblocked spiracles (18.7 nmol g(-1) min(-1) vs. 7.9 nmol g(-1) min(-1)). These findings indicate an important influence of spiracle conductance on the DGC, which may occur mostly in insects showing high spiracular conductances and low metabolic rates. Copyright 2009 Elsevier Ltd. All rights reserved.

  6. Real-Time Gas Identification by Analyzing the Transient Response of Capillary-Attached Conductive Gas Sensor

    Directory of Open Access Journals (Sweden)

    Behzad Bahraminejad

    2010-05-01

    Full Text Available In this study, the ability of the Capillary-attached conductive gas sensor (CGS in real-time gas identification was investigated. The structure of the prototype fabricated CGS is presented. Portions were selected from the beginning of the CGS transient response including the first 11 samples to the first 100 samples. Different feature extraction and classification methods were applied on the selected portions. Validation of methods was evaluated to study the ability of an early portion of the CGS transient response in target gas (TG identification. Experimental results proved that applying extracted features from an early part of the CGS transient response along with a classifier can distinguish short-chain alcohols from each other perfectly. Decreasing time of exposition in the interaction between target gas and sensing element improved the reliability of the sensor. Classification rate was also improved and time of identification was decreased. Moreover, the results indicated the optimum interval of the early transient response of the CGS for selecting portions to achieve the best classification rates.

  7. Thermal desorption-Gas chromatographic methodology for the determination of residual solvents in mesoporous silica.

    Science.gov (United States)

    Asfaw, Adissu Alemayehu; Wolfs, Kris; Schepdael, Ann Van; Adams, Erwin

    2017-06-02

    In this work, thermal desorption-gas chromatography-flame ionization detection (TD-GC-FID) was adapted to enable the determination of residual solvents (RS) in mesoporous silica (MPSi). MPSi is often utilized in various pharmaceutical formulations or drug delivery systems and the accurate determination of RS is an important part of pharmaceutical quality control. Seven commonly used solvents (methanol, ethanol, acetone, isopropanol, dichloromethane, tetrahydrofuran and hexafluoroisopropanol) were evaluated in combination with 3 types of MPSi having pore sizes of 2-3, 15 and 25nm. Validation results showed general recovery values >98% and good linearity over the concentration ranges studied. The limits of detection (LOD) and limits of quantification (LOQ) for the different solvents ranged from 0.03 to 0.08μg and from 0.1 to 0.2μg per tube, respectively. Verification of the accuracy of the TD method was investigated by using an alternative method based on complete dissolution of MPSi in hydrofluoric acid (HF) followed by full evaporation headspace-GC (HS-GC). The results obtained from both procedures were not statistically different (p>0.05) when applied to actual experimental drug samples consisting of itraconazole loaded on MPSi. Copyright © 2017 Elsevier B.V. All rights reserved.

  8. Prediction of Gas Chromatography-Mass Spectrometry Retention Times of Pesticide Residues by Chemometrics Methods

    Directory of Open Access Journals (Sweden)

    Elaheh Konoz

    2013-01-01

    Full Text Available A quantitative structure-retention relationships (QSRRs method is employed to predict the retention time of 300 pesticide residues in animal tissues separated by gas chromatography-mass spectroscopy (GC-MS. Firstly, a six-parameter QSRR model was developed by means of multiple linear regression. The six molecular descriptors that were considered to account for the effect of molecular structure on the retention time are number of nitrogen, Solvation connectivity index-chi 1, Balaban Y index, Moran autocorrelation-lag 2/weighted by atomic Sanderson electronegativity, total absolute charge, and radial distribution function-6.0/unweighted. A 6-7-1 back propagation artificial neural network (ANN was used to improve the accuracy of the constructed model. The standard error values of ANN model for training, test, and validation sets are 1.559, 1.517, and 1.249, respectively, which are less than those obtained reveals by multiple linear regressions model (2.402, 1.858, and 2.036, resp.. Results obtained the reliability and good predictability of nonlinear QSRR model to predict the retention time of pesticides.

  9. Cobalt Doped SnO2 Thick Film Gas Sensors: Conductance and Gas Response Characteristics for LPG and CNG Gas

    Directory of Open Access Journals (Sweden)

    V. Kumar

    2009-02-01

    Full Text Available Cobalt doped thick films tin oxide sensors were studied for their LPG and CNG gas sensitivity. SnO2 powder was synthesized by precipitation technique and doped with cobalt sulphate (0 to 10 wt % by impregnation technique. The sensing characteristics were found to depend on the cobalt concentration and operating temperature. Best performance for LPG and CNG detection was obtained for 3 wt % addition of cobalt sulphate. Cobalt doped SnO2 sensors showed a decrease in the optimum temperature for CNG detection from 450°C to 350°C. The transient response characteristics were determined at different temperatures and doping concentrations to understand the effect of doping on the rate kinetics. A correlation was established between response time, sensor response and the intergranular potential barriers.

  10. NMR and Chemometric Characterization of Vacuum Residues and Vacuum Gas Oils from Crude Oils of Different Origin

    Directory of Open Access Journals (Sweden)

    Jelena Parlov Vuković

    2015-03-01

    Full Text Available NMR spectroscopy in combination with statistical methods was used to study vacuum residues and vacuum gas oils from 32 crude oils of different origin. Two chemometric metodes were applied. Firstly, principal component analysis on complete spectra was used to perform classification of samples and clear distinction between vacuum residues and vacuum light and heavy gas oils were obtained. To quantitatively predict the composition of asphaltenes, principal component regression models using areas of resonance signals spaned by 11 frequency bins of the 1H NMR spectra were build. The first 5 principal components accounted for more than 94 % of variations in the input data set and coefficient of determination for correlation between measured and predicted values was R2 = 0.7421. Although this value is not significant, it shows the underlying linear dependence in the data. Pseudo two-dimensional DOSY NMR experiments were used to assess the composition and structural properties of asphaltenes in a selected crude oil and its vacuum residue on the basis of their different hydrodynamic behavior and translational diffusion coefficients. DOSY spectra showed the presence of several asphaltene aggregates differing in size and interactions they formed. The obtained results have shown that NMR techniques in combination with chemometrics are very useful to analyze vacuum residues and vacuum gas oils. Furthermore, we expect that our ongoing investigation of asphaltenes from crude oils of different origin will elucidate in more details composition, structure and properties of these complex molecular systems.

  11. Gas Phase Pressure Effects on the Apparent Thermal Conductivity of JSC-1A Lunar Regolith Simulant

    Science.gov (United States)

    Yuan, Zeng-Guang; Kleinhenz, Julie E.

    2011-01-01

    Gas phase pressure effects on the apparent thermal conductivity of a JSC-1A/air mixture have been experimentally investigated under steady state thermal conditions from 10 kPa to 100 kPa. The result showed that apparent thermal conductivity of the JSC-1A/air mixture decreased when pressure was lowered to 80 kPa. At 10 kPa, the conductivity decreased to 0.145 W/m/degree C, which is significantly lower than 0.196 W/m/degree C at 100 kPa. This finding is consistent with the results of previous researchers. The reduction of the apparent thermal conductivity at low pressures is ascribed to the Knudsen effect. Since the characteristic length of the void space in bulk JSC-1A varies over a wide range, both the Knudsen regime and continuum regime can coexist in the pore space. The volume ratio of the two regimes varies with pressure. Thus, as gas pressure decreases, the gas volume controlled by Knudsen regime increases. Under Knudsen regime the resistance to the heat flow is higher than that in the continuum regime, resulting in the observed pressure dependency of the apparent thermal conductivity.

  12. Residual radioactive contamination of the test site at Emu from nuclear weapons tests conducted in 1953

    International Nuclear Information System (INIS)

    Maclagan, D.S.; Cooper, M.B.; Duggleby, J.C.

    1979-08-01

    The detailed distributions and soil concentrations of long-lived radionuclides remaining from nuclear weapons trials conducted at Emu in October 1953, are presented. Significant radiation levels due to long-lived neutron activation products in soil, 60 Co and 152 Eu, occur only in the immediate vicinity of the ground zeros of TOTEM 1 and TOTEM 2. It is shown that the levels of contamination due to fallout products in the soil are well below those which would constitute a health hazard to occupants of the area

  13. Modeling the sensing characteristics of chemi-resistive thin film semi-conducting gas sensors.

    Science.gov (United States)

    Ghosh, Abhishek; Majumder, S B

    2017-08-30

    For chemi-resistive thin film gas sensors a generic theoretical model is proposed to predict the variation of sensor response with the operating temperature and thickness of the sensing film. A diffusion equation is formulated assuming that inflammable target gases move through the sensing film by Knudsen diffusion and react with the adsorbed oxygen following first-order kinetics. We have assumed a realistic non-linear variation between the conductance and test gas concentration and derived a general expression relating the sensor response to the operating temperature and thickness of the film. Assuming Langmuir adsorption kinetics, we have theoretically predicted the response and recovery transients during gas sensing using thin film sensing elements. It is predicted that for irreversible type sensing, the response time is reduced with an increase in test gas concentration, whereas for reversible sensing, the response time is independent of test gas concentration. For zinc oxide thin film sensors, an excellent match is obtained between the model prediction and experimental data for their thickness (122 nm to 380 nm) and temperature variation (200 °C to 325 °C) in 500 ppm carbon monoxide (CO) sensing. The maximum CO response% (∼53%) was achieved in 320 nm thick ZnO films. The conductance transients for response and recovery for CO sensing closely follow Langmuir adsorption kinetics and as predicted theoretically, indeed for irreversible sensing, the response time reduces from 350 s to 220 s with an increase in test gas concentration from 20 to 550 ppm. In the case of reversible sensing we found that the response time is ∼55 s irrespective of the CO gas concentration in the range of 5-500 ppm. The models developed in the present work are quite generic in nature and we have discussed their applicability to a wide variety of sensing materials with various types of surface morphologies.

  14. Temperature Dependence of the Thermal Conductivity of a Trapped Dipolar Bose-Condensed Gas

    Science.gov (United States)

    Yavari, H.

    2018-02-01

    The thermal conductivity of a trapped dipolar Bose condensed gas is calculated as a function of temperature in the framework of linear response theory. The contributions of the interactions between condensed and noncondensed atoms and between noncondensed atoms in the presence of both contact and dipole-dipole interactions are taken into account to the thermal relaxation time, by evaluating the self-energies of the system in the Beliaev approximation. We will show that above the Bose-Einstein condensation temperature ( T > T BEC ) in the absence of dipole-dipole interaction, the temperature dependence of the thermal conductivity reduces to that of an ideal Bose gas. In a trapped Bose-condensed gas for temperature interval k B T > k B T, since the relaxation rate {τ}_{c12}^{-1} is independent of temperature and the relaxation rate due to dipolar interaction goes to zero exponentially, the T 2 temperature behavior for the thermal conductivity comes from the thermal mean velocity of the particles. We will also show that in the high-temperature limit ( k B T > n 0 g B ) and low momenta, the relaxation rates {τ}_{c12}^{-1} and {τ}_{dd12}^{-1} change linearly with temperature for both dipolar and contact interactions and the thermal conductivity scales linearly with temperature.

  15. Removal of element mercury by medicine residue derived biochars in presence of various gas compositions

    Energy Technology Data Exchange (ETDEWEB)

    Li, Guoliang [School of Energy and Environmental Engineering, Hebei University of Technology, Tianjin 300401 (China); College of Environmental Science and Engineering, Nankai University, Tianjin 300071 (China); Shen, Boxiong, E-mail: shenbx@nankai.edu.cn [School of Energy and Environmental Engineering, Hebei University of Technology, Tianjin 300401 (China); College of Environmental Science and Engineering, Nankai University, Tianjin 300071 (China); Li, Yongwang [College of Environmental Science and Engineering, Nankai University, Tianjin 300071 (China); Zhao, Bin [School of Chemical Engineering, Hebei University of Technology, Tianjin 300401 (China); Wang, Fumei; He, Chuan; Wang, Yinyin; Zhang, Min [College of Environmental Science and Engineering, Nankai University, Tianjin 300071 (China)

    2015-11-15

    Highlights: • Both physisorption and chemisorption of Hg{sup 0} occurred on the surface of M6WN5. • Chemisorption process was an absolute predominant route for Hg{sup 0} removal by M6WN5. • The effect of NO, H{sub 2}O, SO{sub 2} and O{sub 2} on Hg{sup 0} removal by M6WN5 was investigated. • M6WN5 demonstrated to be a promising Hg{sup 0} sorbent in flue gas. - Abstract: Pyrolyzed biochars from an industrial medicinal residue waste were modified by microwave activation and NH{sub 4}Cl impregnation. Mercury adsorption of different modified biochars was investigated in a quartz fixed-bed reactor. The results indicated that both physisorption and chemisorption of Hg{sup 0} occurred on the surface of M6WN5 which was modified both microwave and 5 wt.% NH{sub 4}Cl loading, and exothermic chemisorption process was a dominant route for Hg{sup 0} removal. Microwave activation improved pore properties and NH{sub 4}Cl impregnation introduced good active sites for biochars. The presence of NO and O{sub 2} increased Hg{sup 0} adsorption whereas H{sub 2}O inhibited Hg{sup 0} adsorption greatly. A converse effect of SO{sub 2} was observed on Hg{sup 0} removal, namely, low concentration of SO{sub 2} promoted Hg{sup 0} removal obviously whereas high concentration of SO{sub 2} suppressed Hg{sup 0} removal. The Hg{sup 0} removal by M6WN5 was mainly due to the reaction of the C−Cl with Hg{sup 0} to form HgCl{sub 2}, and the active state of C−Cl{sup *} groups might be an intermediate group in this process. Thermodynamic analysis showed that mercury adsorption by the biochars was exothermic process and apparent adsorption energy was 43.3 kJ/mol in the range of chemisorption. In spite of low specific surface area, M6WN5 proved to be a promising Hg{sup 0} sorbent in flue gas when compared with other sorbents.

  16. Greenhouse gas reductions through enhanced use of residues in the life cycle of Malaysian palm oil derived biodiesel

    DEFF Research Database (Denmark)

    Hansen, Sune Balle; Olsen, Stig Irving; Ujang, Zaini

    2012-01-01

    This study identifies the potential greenhouse gas (GHG) reductions, which can be achieved by optimizing the use of residues in the life cycle of palm oil derived biodiesel. This is done through compilation of data on existing and prospective treatment technologies as well as practical experiments...... on methane potentials from empty fruit bunches. Methane capture from the anaerobic digestion of palm oil mill effluent was found to result in the highest GHG reductions. Among the solid residues, energy extraction from shells was found to constitute the biggest GHG savings per ton of residue, whereas energy...... extraction from empty fruit bunches was found to be the most significant in the biodiesel production life cycle. All the studied waste treatment technologies performed significantly better than the conventional practices and with dedicated efforts of optimized use in the palm oil industry, the production...

  17. Silver ionic and electronic conductivity in Ag9GaS6

    NARCIS (Netherlands)

    Hellstrom, E.E.; Schoonman, J.

    Electrical measurements on the mixed ionic, electronic conductor Ag9GaS6, which undergoes a phase transition at 303 K, were performed. The silver ionic conductivity in the low-temperature α-form measured using an ionic 4-probe method, is given by σT = 4.3 × 106 exp [(-29.8kJ/mol)/ RT] S m-1 K. The

  18. New portable instrument for the measurement of thermal conductivity in gas process conditions

    Energy Technology Data Exchange (ETDEWEB)

    Queirós, C. S. G. P.; Lourenço, M. J. V., E-mail: mjlourenco@fc.ul.pt; Vieira, S. I.; Nieto de Castro, C. A. [Centro de Química Estrutural, Faculdade de Ciências da Universidade de Lisboa, Campo Grande, 1749-016 Lisboa (Portugal); Serra, J. M. [Instituto Dom Luiz, Faculdade de Ciências da Universidade de Lisboa, Campo Grande, 1749-016 Lisboa (Portugal)

    2016-06-15

    The development of high temperature gas sensors for the monitoring and determination of thermophysical properties of complex process mixtures at high temperatures faces several problems, related with the materials compatibility, active sensing parts sensitivity, and lifetime. Ceramic/thin metal films based sensors, previously developed for the determination of thermal conductivity of molten materials up to 1200 °C, were redesigned, constructed, and applied for thermal conductivity measuring sensors. Platinum resistance thermometers were also developed using the same technology, to be used in the temperature measurement, which were also constructed and tested. A new data acquisition system for the thermal conductivity sensors, based on a linearization of the transient hot-strip model, including a portable electronic bridge for the measurement of the thermal conductivity in gas process conditions was also developed. The equipment is capable of measuring the thermal conductivity of gaseous phases with an accuracy of 2%-5% up to 840 °C (95% confidence level). The development of sensors up to 1200 °C, present at the core of the combustion chambers, will be done in a near future.

  19. Analysis of residual stress in metal-inert-gas-welded Al-2024 using neutron and synchrotron X-ray diffraction

    International Nuclear Information System (INIS)

    Ganguly, S.; Stelmukh, V.; Edwards, L.; Fitzpatrick, M.E.

    2008-01-01

    A combination of neutron and synchrotron X-ray diffraction was used to measure and map the full three-dimensional state of residual stress across the cross-section in coupon samples of metal-inert-gas (MIG)-welded 2024 aluminium alloy. Samples were analysed both as-welded and following a post-welding skim which served to remove the weld flash and reduce the plate thickness. The profile of the residual stress and its evolution following skimming has been accurately characterized. The longitudinal direction shows the highest residual stress, approaching 300 MPa in tension. The skimming treatment did not change the peak stress, but the overall profile of stress was altered: this is slightly unexpected as machining away stressed material would generally be expected to reduce the peak residual stress. The results are discussed in terms of the generation of stress during welding and its evolution during skimming. Finally a comparison is made with the stress generated in the as-welded and skimmed conditions of a variable polarity plasma arc (VPPA)-welded specimen of similar dimensions, to show the effects of different weld processes on the residual stress generated. The stress measurement in the VPPA sample was carried out under near identical experimental conditions

  20. Tunneling conductance of a two-dimensional electron gas with Dresselhaus spin-orbit coupling

    International Nuclear Information System (INIS)

    Srisongmuang, B.; Ka-oey, A.

    2012-01-01

    We theoretically studied the spin-dependent charge transport in a two-dimensional electron gas with Dresselhaus spin-orbit coupling (DSOC) and metal junctions. It is shown that the DSOC energy can be directly measured from the tunneling conductance spectrum. We found that spin polarization of the conductance in the propagation direction can be obtained by injecting from the DSOC system. We also considered the effect of the interfacial scattering barrier (both spin-flip and non-spin-flip scattering) on the overall conductance and the spin polarization of the conductance. It is found that the increase of spin-flip scattering can enhance the conductance under certain conditions. Moreover, both types of scattering can increase the spin polarization below the branches crossing of the energy band. - Highlights: → DSOC energy can be directly measured from tunneling conductance spectrum. → Spin polarization of conductance in the propagation direction can be obtained by injecting from DSOC system. → Both types of scattering can increase spin polarization.

  1. (210)Pb content in natural gas pipeline residues ("black-powder") and its correlation with the chemical composition.

    Science.gov (United States)

    Godoy, José Marcus; Carvalho, Franciane; Cordilha, Aloisio; Matta, Luiz Ernesto; Godoy, Maria Luiza

    2005-01-01

    The present work was carried out to assess the (210)Pb content in "black-powder" found in pigging operations on gas pipelines in Brazil, in particular, on the Campos Basin gas pipeline. Additionally, the chemical composition of such deposits was determined and an eventual correlation with (210)Pb concentration evaluated. Typical "black-powder" generated in the natural gas pipeline from Campos Basin oilfield contains mainly iron oxide ( approximately 81%) and residual organic matter ( approximately 9%). The (210)Pb content ranges from 4.9 to 0.04k Bqkg(-1) and seems to be inversely correlated with the distance to the platforms. On the other hand, (226)Ra concentration is higher on the pipeline branch between the platform and the onshore installations. (228)Ra was only observed in few samples, in particular, in the samples with the highest (226)Ra content.

  2. Design of internal structures of conductance sensors for gas-water two-phase flow measurement

    Science.gov (United States)

    Yu, Xuelian; Dong, Feng; Tan, Chao; Wei, Can

    2012-03-01

    Conductance sensor array is widely used in measuring two-phase flow parameters, in this paper we propose a new configuration of conductance sensors with six rectangular electrodes of same size from the pipe facing to an inner ring-type electrode and use it to measure gas cross-sectional-averaged water holdup value. The designed six rectangular electrodes are axially flush-mounted on the inside wall of an insulating duct. The geometry of six electrodes conductance sensor was determined with finite element numerical analysis. Sensor optimization of the electric field such as uniformity, spatial sensitivity is proposed. This configuration can improve measurement accuracy, through analyze sensitivity distribution, the role of soft field is discussed, and acquired the final size of the electrodes in the end. The simulation results were obtained from COMSOL Multiphysics finite element software.

  3. RESIDUAL GAS MOTIONS IN THE INTRACLUSTER MEDIUM AND BIAS IN HYDROSTATIC MEASUREMENTS OF MASS PROFILES OF CLUSTERS

    International Nuclear Information System (INIS)

    Lau, Erwin T.; Kravtsov, Andrey V.; Nagai, Daisuke

    2009-01-01

    We present analysis of bulk and random gas motions in the intracluster medium using high-resolution Eulerian cosmological simulations of 16 simulated clusters, including both very relaxed and unrelaxed systems and spanning a virial mass range of 5 x 10 13 - 2 x 10 15 h -1 M-odot. We investigate effects of the residual subsonic gas motions on the hydrostatic estimates of mass profiles and concentrations of galaxy clusters. In agreement with previous studies, we find that the gas motions contribute up to ∼5%-15% of the total pressure support in relaxed clusters with contribution increasing with the cluster-centric radius. The fractional pressure support is higher in unrelaxed systems. This contribution would not be accounted for in hydrostatic estimates of the total mass profile and would lead to systematic underestimate of mass. We demonstrate that total mass can be recovered accurately if pressure due to gas motions measured in simulations is explicitly taken into account in the equation of hydrostatic equilibrium. Given that the underestimate of mass is increasing at larger radii, where gas is less relaxed and contribution of gas motions to pressure is larger, the total density profile derived from hydrostatic analysis is more concentrated than the true profile. This may at least partially explain some high values of concentrations of clusters estimated from hydrostatic analysis of X-ray data.

  4. Transport properties of N2 gas at cryogenic temperatures. [computation of viscosity and thermal conductivity

    Science.gov (United States)

    Pearson, W. E.

    1974-01-01

    The viscosity and thermal conductivity of nitrogen gas for the temperature range 5 K - 135 K have been computed from the second Chapman-Enskog approximation. Quantum effects, which become appreciable at the lower temperatures, are included by utilizing collision integrals based on quantum theory. A Lennard-Jones (12-6) potential was assumed. The computations yield viscosities about 20 percent lower than those predicted for the high end of this temperature range by the method of corresponding states, but the agreement is excellent when the computed values are compared with existing experimental data.

  5. Water-Gas Shift Reaction Catalyzed by Redox Enzymes on Conducting Graphite Platelets

    OpenAIRE

    Lazarus, Oliver; Woolerton, Thomas W.; Parkin, Alison; Lukey, Michael J.; Reisner, Erwin; Seravalli, Javier; Pierce, Elizabeth; Ragsdale, Stephen W.; Sargent, Frank; Armstrong, Fraser A.

    2009-01-01

    The water-gas shift (WGS) reaction (CO + H2O ⇆ CO2 + H2) is of major industrial significance in the production of H2 from hydrocarbon sources. High temperatures are required, typically in excess of 200 °C, using d-metal catalysts on oxide supports. In our study the WGS process is separated into two half-cell electrochemical reactions (H+ reduction and CO oxidation), catalyzed by enzymes attached to a conducting particle. The H+ reduction reaction is catalyzed by a hydrogenase, Hyd-2, from Esc...

  6. Direct gas-solid carbonation of serpentinite residues in the absence and presence of water vapor: a feasibility study for carbon dioxide sequestration.

    Science.gov (United States)

    Veetil, Sanoopkumar Puthiya; Pasquier, Louis-César; Blais, Jean-François; Cecchi, Emmanuelle; Kentish, Sandra; Mercier, Guy

    2015-09-01

    Mineral carbonation of serpentinite mining residue offers an environmentally secure and permanent storage of carbon dioxide. The strategy of using readily available mining residue for the direct treatment of flue gas could improve the energy demand and economics of CO2 sequestration by avoiding the mineral extraction and separate CO2 capture steps. The present is a laboratory scale study to assess the possibility of CO2 fixation in serpentinite mining residues via direct gas-solid reaction. The degree of carbonation is measured both in the absence and presence of water vapor in a batch reactor. The gas used is a simulated gas mixture reproducing an average cement flue gas CO2 composition of 18 vol.% CO2. The reaction parameters considered are temperature, total gas pressure, time, and concentration of water vapor. In the absence of water vapor, the gas-solid carbonation of serpentinite mining residues is negligible, but the residues removed CO2 from the feed gas possibly due to reversible adsorption. The presence of small amount of water vapor enhances the gas-solid carbonation, but the measured rates are too low for practical application. The maximum CO2 fixation obtained is 0.07 g CO2 when reacting 1 g of residue at 200 °C and 25 barg (pCO2 ≈ 4.7) in a gas mixture containing 18 vol.% CO2 and 10 vol.% water vapor in 1 h. The fixation is likely surface limited and restricted due to poor gas-solid interaction. It was identified that both the relative humidity and carbon dioxide-water vapor ratio have a role in CO2 fixation regardless of the percentage of water vapor.

  7. Study of electrical conductivity response upon formation of ice and gas hydrates from salt solutions by a second generation high pressure electrical conductivity probe

    Science.gov (United States)

    Sowa, Barbara; Zhang, Xue Hua; Kozielski, Karen A.; Dunstan, Dave E.; Hartley, Patrick G.; Maeda, Nobuo

    2014-11-01

    We recently reported the development of a high pressure electrical conductivity probe (HP-ECP) for experimental studies of formation of gas hydrates from electrolytes. The onset of the formation of methane-propane mixed gas hydrate from salt solutions was marked by a temporary upward spike in the electrical conductivity. To further understand hydrate formation a second generation of window-less HP-ECP (MkII), which has a much smaller heat capacity than the earlier version and allows access to faster cooling rates, has been constructed. Using the HP-ECP (MkII) the electrical conductivity signal responses of NaCl solutions upon the formation of ice, tetrahydrofuran hydrates, and methane-propane mixed gas hydrate has been measured. The concentration range of the NaCl solutions was from 1 mM to 3M and the driving AC frequency range was from 25 Hz to 5 kHz. This data has been used to construct an "electrical conductivity response phase diagrams" that summarize the electrical conductivity response signal upon solid formation in these systems. The general trend is that gas hydrate formation is marked by an upward spike in the conductivity at high concentrations and by a drop at low concentrations. This work shows that HP-ECP can be applied in automated measurements of hydrate formation probability distributions of optically opaque samples using the conductivity response signals as a trigger.

  8. Code of Conduct for Gas Marketers : rule made under part 3 of the Ontario Energy Board Act, 1998

    International Nuclear Information System (INIS)

    1999-01-01

    Text of the code of conduct for gas marketers in Ontario is presented. This code sets the minimum standards under which a gas marketer may sell or offer to sell gas to a low-volume consumer, or act as an agent or broker with respect to the sale of gas. The document describes the standards and principles regarding: (1) fair marketing practices, (2) identification, (3) information to be maintained by a gas marketer, (4) confidentiality of consumer information, (5) conditions in offers, (6) contracts, (7) contract renewals, (8) assignment, sale and transfer contracts, (9) independent arms-length consumer complaints resolution process, and (10) penalties for breach of this code

  9. Code of Conduct for Gas Marketers : rule made under part 3 of the Ontario Energy Board Act, 1998

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-02

    Text of the code of conduct for gas marketers in Ontario is presented. This code sets the minimum standards under which a gas marketer may sell or offer to sell gas to a low-volume consumer, or act as an agent or broker with respect to the sale of gas. The document describes the standards and principles regarding: (1) fair marketing practices, (2) identification, (3) information to be maintained by a gas marketer, (4) confidentiality of consumer information, (5) conditions in offers, (6) contracts, (7) contract renewals, (8) assignment, sale and transfer contracts, (9) independent arms-length consumer complaints resolution process, and (10) penalties for breach of this code.

  10. Determination of 86 Pesticide Residues in Leafy Vegetables using gas Chromatography Mass Spectrometry

    OpenAIRE

    , M. T. Selim; , I. Al-Dossary

    2016-01-01

    A multiresidue method is described for detection and determination of 86 compounds of pesticide residues which commonly used in the pest control programs for crop protection. Good sensitivity and selectivity of the method are obtained with limits of quantiŞcation 0.01 mg/kg in almost all cases. The method was applied very satisfactorily to routine analysis as a complement to traditional GC-MS method and Şnally, limit of detection were also 10-20 times lower than maximum residue levels (MRL) e...

  11. Screening of the presence organophosphates and organochlorines pesticide residues in vegetables and fruits using gas chromatography-mass spectrometry

    Science.gov (United States)

    Putri, Dillani; Aryana, Nurhani; Aristiawan, Yosi; Styarini, Dyah

    2017-01-01

    Pesticides is commonly used to improve the quality of agricultural product, especially in vegetables and fruits. Due to pesticide residues in the product become a concern to consumer health, monitoring and analysis of pesticide residues in agriculture product need to be established. The certified reference material (CRM) is often benefited to obtain accurate results in analysis. It is required as the quality control to improve quality assurance of the testing results. Unfortunately in Indonesia, the development of matrix CRM for the analysis of pesticide residues in vegetables and fruits is still limited. This study is aimed to determine the type of commodity and target analyte to be employed in the development of CRM for pesticides in vegetables and fruits. As the preliminary study, the screening of 11 commodities of fresh vegetables and fruits has been conducted to review the information about the presence of organophosphates (OPs) and organochlorines (OCs) in the sample. In this analysis, QuEChERS technique was used in the extraction process and the qualitative analysis was evaluated by using GC-MS. The results showed that strawberry and celery contain residues of pesticide chlorpyrifos. Further analysis of the commodity celery from seven different places has been conducted, resulting that from 3 of all 7 samples (43%) were positive containing chlorpyrifos. Therefore, the development of CRM for chlorpyrifos in celery will be our next research project.

  12. Energy and greenhouse gas balance of the use of forest residues for bioenergy production in the UK

    International Nuclear Information System (INIS)

    Whittaker, Carly; Mortimer, Nigel; Murphy, Richard; Matthews, Robert

    2011-01-01

    Life cycle analysis is used to assess the energy requirements and greenhouse gas (GHG) emissions associated with extracting UK forest harvesting residues for use as a biomass resource. Three forest harvesting residues were examined (whole tree thinnings, roundwood and brash bales), and each have their own energy and emission profile. The whole forest rotation was examined, including original site establishment, forest road construction, biomass harvesting during thinning and final clear-fell events, chipping and transportation. Generally, higher yielding sites give lower GHG emissions per ‘oven dried tonne’ (ODT) forest residues, but GHG emissions ‘per hectare’ are higher as more biomass is extracted. Greater quantities of biomass, however, ultimately mean greater displacement of conventional fuels and therefore greater potential for GHG emission mitigation. Although forest road construction and site establishment are “one off” events they are highly energy-intensive operations associated with high diesel fuel consumption, when placed in context with the full forest rotation, however, their relative contributions to the overall energy requirements and GHG emissions are small. The lower bulk density of wood chips means that transportation energy requirements and GHG emissions are higher compared with roundwood logs and brash bales, suggesting that chipping should occur near the end-user of application. -- Highlights: ► GHGs and fuel consumption assessed for UK clear-fell conifer forest residues. ► Energy use and GHG emissions for forest road construction characterised. ► Lower energy requirements and GHG emissions per ODT for higher yielding sites. ► Transport energy and GHG emissions higher for wood chip than roundwood or brash bales. ► Results useful in predicting GHG mitigation potential from UK commercial conifer forest residues.

  13. JV Task 5 - Evaluation of Residual Oil Fly Ash As A Mercury Sorbent For Coal Combustion Flue Gas

    Energy Technology Data Exchange (ETDEWEB)

    Robert Patton

    2006-12-31

    The mercury adsorption capacity of a residual oil fly ash (ROFA) sample collected form Florida Power and Light Company's Port Everglades Power Plant was evaluated using a bituminous coal combustion flue gas simulator and fixed-bed testing protocol. A size-segregated (>38 {micro}g) fraction of ROFA was ground to a fine powder and brominated to potentially enhance mercury capture. The ROFA and brominated-ROFA were ineffective in capturing or oxidizing the Hg{sup 0} present in a simulated bituminous coal combustion flue gas. In contrast, a commercially available DARCO{reg_sign} FGD initially adsorbed Hg{sup 0} for about an hour and then catalyzed Hg{sup 0} oxidation to produce Hg{sup 2+}. Apparently, the unburned carbon in ROFA needs to be more rigorously activated in order for it to effectively capture and/or oxidize Hg{sup 0}.

  14. Determination of pesticide residues (> 0.5 microg/L) in soft drinks and sports drinks by gas chromatography with mass spectrometry: collaborative study.

    Science.gov (United States)

    Miller, Kathleen D; Milne, Paul

    2008-01-01

    A collaborative study was conducted on a method for the measurement of 19 low-level pesticide residues in soft drinks and sports drinks by gas chromatography with mass spectrometry (GC/MS). The pesticide residues determined were 2,4'-dichlorodiphenyldichloroethylene (2,4'-DDE); 2,4'-dichlorodiphenyldichloroethane (2,4'-DDD); 4,4'-dichlorodiphenyldichloroethylene (4,4'-DDE); 2,4'-dichlorodiphenyltrichloroethane (2,4'-DDT); 4,4'-dichlorodiphenyltrichloroethane (4,4'-DDT); 4,4'-dichlorodiphenyldichloroethane (4,4'-DDD); alpha-endosulfan; endosulfan-sulfate; dieldrin; aldrin; ethion; chlorpyrifos; beta-endosulfan; malathion; methyl-parathion; alpha-hexachlorocyclohexane (alpha-HCH); beta-HCH; delta-HCH; and gamma-HCH. Blind fortification solutions containing 4 different levels of pesticide residues (0, 0.1, 0.5, and 1.0 microg/L) were provided to 8 collaborating laboratories who used them to create test samples in 6 matrixes (also provided): 2 colas, a diet cola, a clear lemon-lime soft drink, an orange soft drink, and a sports drink. Reproducibility (RSDR) for all 19 pesticide residues in all matrixes ranged from 7 to 151% at the 0.1 microg/L level, 11 to 121% at 0.5 microg/L, and 14 to 67% at 1.0 microg/L. Repeatability (RSDr), applicable to the diet cola and the sports drink, ranged from 1 to 76% for the 19 pesticide residues at the 0.1 microg/L level, 9 to 38% at 0.5 microg/L, and 9 to 38% at 1.0 microg/L. Recoveries for the 19 pesticide residues in all matrixes ranged from 77 to 645% at the 0.1 microg/L level, 60 to 231% at 0.5 microg/L, and 61 to 146% at 1.0 microg/L. It is recommended that the method be accepted by AOAC as Official First Action with a limit of quantification (LOQ) equal to 0.5 microg/L for 4,4'-DDT; 2,4'-DDT; 2,4'-DDD; 4,4'-DDE; 4,4'-DDD; 2,4'-DDE; aldrin; dieldrin; alpha-endosulfan; endosulfan-sulfate; chlorpyrifos; and ethion, and an LOQ equal to 1.0 microg/L for beta-endosulfan; alpha-HCH; beta-HCH; delta-HCH; gamma-HCH; methyl-parathion; and

  15. Acoustical gas-leak detection in the presence of multiple reflections, dispersion, and uncorrelated noise using optimized residual complexity.

    Science.gov (United States)

    Ahmadi, A M; Amjadi, A; Bahrampour, A R; Ravanbod, H; Tofighi, S

    2016-09-01

    Precise acoustical leak detection calls for robust time-delay estimates, which minimize the probability of false alarms in the face of dispersive propagation, multiple reflections, and uncorrelated background noise. Providing evidence that higher order modes and multi-reflected signals behave like sets of correlated noise, this work uses a regression model to optimize residual complexity in the presence of both correlated and uncorrelated noise. This optimized residual complexity (ORC) is highly robust since it takes into account both the level and complexity of noise. The lower complexity of the dispersive modes and multiple reflections, compared to the complexity of the plane mode, points to the robustness of ORC against multiple reflections and dispersion. Experimental investigations using recorded sounds of gas leaking from a pipe confirm the robustness of ORC against multiple reflections. Numerical simulations also show robustness against dispersive modes, even when they disturb the linearity of the cross-spectrum phase. Comparisons with other methods-mutual information, cross correlation, and residual complexity-underline the general advantages of ORC in terms of robustness in the presence of reflection and dispersion, against both correlated and uncorrelated noise, and to short signals.

  16. Simultaneous determination of organochlorine and pyrethriod pesticide residues in the Chinese patent medicines by gas chromatography-tandem mass spectrometry.

    Science.gov (United States)

    Mao, Xue J; Zhong, Yao; Yan, Ai P; Wang, Bin; Wang, Yuan X; Wan, Yi Q

    2018-02-01

    A simple, sensitive, reliable method was developed for the simultaneous determination of organochlorine and pyrethriod pesticide residues in Chinese patent medicines Six ingredient rehmannia pills and Xiaoyao pills. These pesticides were extracted by ethyl acetate. The extraction time and volume of ethyl acetate were optimized. Cleanup of extracts was performed with dispersive-solid phase extraction using graphitized carbon black as the sorbent. The determination of pesticides in the final extracts was carried out by gas chromatography-tandem mass spectrometry in multiple reaction monitoring mode (GC-MS/MS, MRM). The linearity of the calibration curves is good in matrix-matched standard and yields the coefficients of determination (R 2 ) ≥0.99 for all of the target analytes. Under optimized conditions, the average recoveries (five replicates) for most pesticides range from 75.5% to 114.6%, and RSDs are less than 10.0%. The LODs of 18 pesticides in Six ingredient rehmannia pill and Xiaoyao pills are in the range of 0.01-8.82 μg kg -1 . The developed method meets the requirements of pesticide residue analysis and could be effectively used for routine analysis of the organochlorine and pyrethriod pesticide residues in Six ingredient rehmannia pills and Xiaoyao pills.

  17. Evaluation of gas chromatography – electron ionization – full scan high resolution Orbitrap mass spectrometry for pesticide residue analysis

    Energy Technology Data Exchange (ETDEWEB)

    Mol, Hans G.J., E-mail: hans.mol@wur.nl; Tienstra, Marc; Zomer, Paul

    2016-09-07

    Gas chromatography with electron ionization and full scan high resolution mass spectrometry with an Orbitrap mass analyzer (GC-EI-full scan Orbitrap HRMS) was evaluated for residue analysis. Pesticides in fruit and vegetables were taken as an example application. The relevant aspects for GC-MS based residue analysis, including the resolving power (15,000 to 120,000 FWHM at m/z 200), scan rate, dynamic range, selectivity, sensitivity, analyte identification, and utility of existing EI-libraries, are assessed and discussed in detail. The optimum acquisition conditions in full scan mode (m/z 50–500) were a resolving power of 60,000 and an automatic-gain-control target value of 3E6. These conditions provided (i) an optimum mass accuracy: within 2 ppm over a wide concentration range, with/without matrix, enabling the use of ±5 ppm mass extraction windows (ii) adequate scan speed: minimum 12 scans/peak, (iii) an intra-scan dynamic range sufficient to achieve LOD/LOQs ≤0.5 pg in fruit/vegetable matrices (corresponding to ≤0.5 μg kg{sup −1}) for most pesticides. EI-Orbitrap spectra were consistent over a very wide concentration range (5 orders) with good match values against NIST (EI-quadrupole) spectra. The applicability for quantitative residue analysis was verified by validation of 54 pesticides in three matrices (tomato, leek, orange) at 10 and 50 μg/kg. The method involved a QuEChERS-based extraction with a solvent switch into iso-octane, and 1 μL hot splitless injection into the GC-HRMS system. A recovery between 70 and 120% and a repeatability RSD <10% was obtained in most cases. Linearity was demonstrated for the range ≤5–250 μg kg{sup −1}. The pesticides could be identified according to the applicable EU criteria for GC-HRMS (SANTE/11945/2015). GC-EI-full scan Orbitrap HRMS was found to be highly suited for quantitative pesticide residue analysis. The potential of qualitative screening to extend the scope makes it an attractive

  18. Determination of daminozide residues in apples using gas chromatography with nitrogen-phosphorus detection

    NARCIS (Netherlands)

    Brinkman, J.H.W.; Dijk, A.G. van; Wagenaar, R.; Quirijns, J.K.

    1996-01-01

    A method was developed for the determination of daminozide in apples using gas chromatography (GC) with nitrogen-phosphorus detection (NPD). Daminozide is hydrolysed to 1,1-dimethylhydrazine (UDMH) by alkaline digestion. The UDMH generated is distilled from the apple matrix, derivatized with

  19. Conversion of forest residues to a clean gas for fuel or synthesis

    Energy Technology Data Exchange (ETDEWEB)

    Feldmann, H.F.; Liu, K.T.; Longanbach, J.R.; Curran, L.M.; Chauhan, S.P.

    1979-01-01

    A program is described for developing a gasification system specifically for wood and other biomass materials which allows greatly increased gasifier throughputs and direct catalysis of wood. Wood ash, which is a by-product of a wood gasification plant, can be used as a gasification catalyst for wood, as it increases gasification rates and promotes the water-gas shift reaction. The high reactivity of even uncatalyzed biomass allows the potential of very high gasifier throughputs. However, the achievement of this potential requires that the gasifier operate at gas velocities higher than those attainable in conventional reactor systems. Stable and very smooth fluidization with uniform mixing and distribution of chips throughout the bed was observed on addition of an entrained sand phase to a fluidized bed of alumina and wood chips. Economc feasibility studies based on utilization of a proprietary Battelle gasification system which utilizes an entrained-phase heat carrier indicated that an intermediate-Btu gas can be produced in 1000 ton/day plants at a price competitive with liquefied natural gas and No. 2 heating oil.

  20. Pyrolysis Gas as a Renewable Reducing Agent for the Recycling of Zinc- and Lead-Bearing Residues: A Status Report

    Science.gov (United States)

    Pichler, C.; Antrekowitsch, J.

    2017-04-01

    The topic "Zero Waste" has been in existence for several years in the industry, and the metallurgical industry has also made efforts to reduce the amounts of residues occurring and have started several investigations to cut down on metallurgical by-products which have to be landfilled. Especially, the additional costs for CO2 emissions in different metallurgical steps have led to investigations into alternative carbon carriers. Charcoal has been identified to serve as an ideal substitute due its CO2-neutrality. For the applications of this renewable carbon carrier in metallurgical processes, charcoal production by means of a carbonization process needs to be optimized. As a by-product during the heating of agricultural wastes or wood by excluding air, pyrolysis gas occurs. Due to the existence of combustible compounds in this gas, an application as a reduction agent instead of fossil carbon carriers in metallurgy is possible. Based on the prevention of dumping metallurgical by-products, an investigation has been developed to treat zinc- and lead-containing materials. To realize this, a dedicated process concept has been designed and developed. As the main focuses, the usage of the pyrolysis gas from charcoal production for the Waelz kiln process and the recycling of zinc- and lead-containing Waelz slag, resulting from the processing of steel mill dust in a vertical retort, have to be mentioned. Within this research, the process concept was executed from laboratory-scale up to pilot-scale testing, described in this article.

  1. Conversion of forest residues to a methane-rich gas: Interim Report

    Energy Technology Data Exchange (ETDEWEB)

    Feldmann, H.G.; Paisley, M.A.; Appelbaum, H.R.

    1986-03-01

    A process is being developed that produces a fuel gas with a heating value of 500 Btu/SCF from diverse forms of biomass, including shredded bark, wood chips, and sawdust. The system uses a high throughput, non-oxygen gasifier that employs sand circulation to supply process heat. Results obtained with a 10-inch I.D. gasifier are presented and compared with those in a 6-inch I.D. reactor. Feed rates up to 12 tons/day (dry) have been achieved corresponding to a specific wood throughput of 2000 lbs/ft/sup 2/-hr. Gas compositions in the two reactors are in excellent agreement and performance in the larger reactor, as measured by carbon conversion, is significantly improved. Cost projections comparing this process with direct combustion are presented that indicate gasification technology should have very significant cost advantages for both generation of plant steam and cogeneration of electricity. 5 refs., 14 figs., 5 tabs.

  2. A Vapor Challenge Method of Measuring the Residual Life of Gas Filters

    Science.gov (United States)

    1990-08-01

    reaction with chromium complexes . Protection against these gases is so effective that these gases are no longer used in gas warfare; however...To do otherwise, would increase the complexity of the test, and provide a less direct measurement of filter performance under actual operation. Second...detected by colorimetric reactions with: * chromotropic acid; 6 J-acid; 0 metal precipitation from nickel dimethylglyoxime ; or 0 metal precipitation from

  3. Simultaneous determination of lincomycin and spectinomycin residues in animal tissues by gas chromatography-nitrogen phosphorus detection and gas chromatography-mass spectrometry with accelerated solvent extraction.

    Science.gov (United States)

    Tao, Y; Chen, D; Yu, G; Yu, H; Pan, Y; Wang, Y; Huang, L; Yuan, Z

    2011-02-01

    A new multi-dimensional analytical method using gas chromatography-nitrogen phosphorus detection (GC-NPD) and gas chromatography-mass spectrometry (GC-MS) was developed for qualitative and quantitative measurement of lincomycin and spectinomycin residues in food animal tissues. This method is based on a new extraction procedure using accelerated solvent extraction (ASE). The analytes were extracted by phosphate buffer with trichloroacetic acid deproteinization and clean-up by C₁₈ solid-phase extraction (SPE) adding dodecanesulfonic acid sodium salt as an ion-pair reagent. The eluted fraction was evaporated and derivatised with N,O-bis(trimethylsilyl) trifluoroacetamide (BSTFA) for GC-NPD analysis and GC-MS confirmation. Parameters for extraction pressure, temperature and cycle of ASE, clean-up, derivatisation and analysis procedure were optimised. The method was validated in muscle, kidney and liver of swine, bovine with a low concentration (limit of quantification) of 16.4 and 21.4 µg kg⁻¹ for these two analytes using GC-NPD. For GC-MS, the limits of quantification were 4.1 and 5.6 µg kg⁻¹, respectively. Spiked recoveries from levels of 20 to 200 µg kg⁻¹ were found to be between 73% and 99% with a relative standard deviation (RSD) of less than 17% in GC-NPD. For GC-MS, levels from 5 to 20 µg kg⁻¹ had between 70% and 93% with an RSD of less than 21%. This rapid and reliable method can be used for the characterisation and quantification of residues of lincomycin and spectinomycin in animal tissues.

  4. [Analysis of residues of organochlorine compounds in plant drugs. 3. Identification of residues of polychlorobiphenyl compounds by comparison of gas chromatography on packed and capillary columns and GCMS coupling].

    Science.gov (United States)

    Benecke, R; Brotka, J; Wijsbeek, J; Franke, J P; Bruins, A P; de Zeeuw, R A

    1988-02-01

    The identification of residues of polychlorinated biphenyls in a test sample of Flores Chamomillae could be achieved by the retention behavior at gas chromatographic analyses on packed and capillary columns compared with reference standard Clophen A 60, respectively as well as well by capillary GC/MS using single ion monitoring of substance-characteristic ion mass.

  5. Multi-Residue Analysis of Pesticides in Pistachio Using Gas Chromatography-Mass Spectrometry (GC/MS

    Directory of Open Access Journals (Sweden)

    Azadeh Emami

    2014-12-01

    Full Text Available Background: Analysis of pesticide residues in food and other environmental commodities have become an essential requirement for consumers, producers, food inspectors and authorities. This study is focused on validation of an accurate, rapid and reliable method for multi-residual analysis of pesticides in pistachio as a strategic crop for export and one of the main nuts in Iranian food basket. Methods: We developed a "Quick, Easy, Cheap, Effective, Rugged, and Safe (QuEChERS method based on spiking blank samples and used the data for drawing calibration curves instead of standard solutions. Sample preparations were developed for determination of 12 pesticide residues in pistachio by gas chromatography-mass spectrometry (GC/MS. Results: Recovery of pesticides at 5 concentration levels (n=3 was in the range of 81.40% - 93.08 %. The method proved to be repeatable in the majority of samples with relative standard deviation (RSD of lower than 20%. The limits of detection and quantification for all pesticides were 2 ppb and 10 ppb, respectively. Conclusion: The calibration curves of pesticides were linear in the range of 10-500 (ng/g and correlation coefficient of entire pesticides was higher than 0.994. The recovery of pesticides at 5 concentration levels (n=3 was in range of 81.41- 91.80 %. The method was proved to be repeatable with the majority of RSDs being lower than 20%. The limits of detection and quantification for all pesticides were 2 and 10 ppb, respectively. The recoveries and repeatabilities were in accordance with the criteria set by SANCO Guideline (Commission of the European Communities, 2006.

  6. Validation of a new analytical procedure for determination of residual solvents in [{sup 18}F]FDG by gas chromatography

    Energy Technology Data Exchange (ETDEWEB)

    Costa, Flávia M.; Costa, Cassiano L.S.; Silva, Juliana B.; Ferreira, Soraya M.Z.M.D., E-mail: flaviabiomedica@yahoo.com.br [Centro de Desenvolvimento da Tecnologia Nuclear (UPPR/CDTN/CNEN-MG), Belo Horizonte, MG (Brazil). Unidade de Pesquisa e Produção de Radiofármacos

    2017-07-01

    Fludeoxyglucose F 18 ([{sup 18}F]FDG) is the most used radiopharmaceutical for positron emission tomography, especially on oncology. Organic solvents such as ether, ethanol and acetonitrile might be used in the synthesis of [{sup 18}F]FDG; however, they might not be completely removed during purification steps. The determination of residual solvents in [{sup 18}F]FDG is required in the European Pharmacopoeia (EP) and the United States Pharmacopeia (USP) monographs. While the procedure described in the EP is quite general, the one described in the USP requires a long runtime (about 13 minutes). In this work a simple and fast (4-minute) analytical procedure was developed and validated for determination of residual solvents in [{sup 18}F]FDG. Analyses were carried out in a Perkin Elmer gas chromatograph equipped with a flame ionization detector. The separation was obtained on a 0.53-mm x 30 m fused-silica column. Validation included the evaluation of various parameters, such as: specificity, linearity and range, limits of detection and quantitation, precision (repeatability and intermediate precision), accuracy, and robustness. Results were found to be within acceptable limits, indicating the developed procedure is suitable for its intended application. Considering the short half-life of fluorine-18 (109.7 minutes), this new method could be a valuable alternative for routine quality control of [{sup 18}F]FDG. (author)

  7. Gas Chromatographic Method: Tool for Rapid and Sensitive Analysis of Residual Solvents in Amoxicillin and Ampicillin Tablets

    Directory of Open Access Journals (Sweden)

    Sk Manirul Haque

    2015-12-01

    Full Text Available A simple and sensitive static head space gas chromatographic (SH-GC method equipped with FID has been developed and validated for simultaneous determination of residual solvents e.g.,  methanol, dichloromethane and toluene in two therapeutic drugs such as amoxicillin  and ampicillin. The separation was achieved with 30 m long Elite - 5 fused silica capillary column and 0.32 mm inner diameter. The developed SH-GC method offered symmetric peak shape, good resolution and reasonable retention time for all the solvents. Beer’s law was obeyed in the concentration ranges 100 – 1200, 50 – 1000 and 50 – 500 ppm for methanol, dichloromethane and toluene, respectively. The method was validated according to international conference on harmonization (ICH guidelines in terms of specificity, linearity, precision, accuracy, limit of detection, limit of quantitation, robustness and solution stability. The degrees of linearity of the calibration curves, the percent recoveries, relative standard deviation for the method were also determined. All the validation parameters were within the acceptable range. The developed SH-GC method could, therefore, be suitable for simple and rapid detection of trace levels residual solvents in other pharmaceutical products and thereby it could be used for routine analysis in any analytical laboratory.

  8. The Continuation Study of the Measurement of Residual Monomer from theDenture Base After Three Month Worn by Gas Chromatography on the Radiationand Non Radiation Worker

    International Nuclear Information System (INIS)

    Isyuniarto; Winoto

    2000-01-01

    Residual monomer measurement on the radiation and non radiation workerafter three month worn the denture has been done. The aim of the research isto investigated residual monomer concentration on after three month worn. Thedenture base material, made of resin acrylic, sometimes is cause mucosairritation in the mouth, and dental irritation or allergic reaction, becauseof residual monomer that left on the mouth cavity. In this research two groupwere needed there are the radiation and non radiation worker, the level ofthe residual monomer count by gas chromatography analysis. The result of thisresearch showed that the level of residual monomer of two group are same orthere have same level of the limit value. The measurement result is in therange of 0.1783 ± 0.011 mg/l to 0.1790 ± 0.004 mg/l. (author)

  9. Transparent conducting films of hierarchically nanostructured polyaniline networks on flexible substrates for high-performance gas sensors.

    Science.gov (United States)

    Bai, Shouli; Sun, Chaozheng; Wan, Pengbo; Wang, Cheng; Luo, Ruixian; Li, Yaping; Liu, Junfeng; Sun, Xiaoming

    2015-01-21

    Transparent chemical gas sensors are assembled from a transparent conducting film of hierarchically nanostructured polyaniline (PANI) networks fabricated on a flexible PET substrate, by coating silver nanowires (Ag NWs) followed by the in situ polymerization of aniline near the sacrificial Ag NW template. The sensor exhibits enhanced gas sensing performance at room temperature in both sensitivity and selectivity to NH3 compared to pure PANI film. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  10. Effect of wall thermal conductivity on the heat transfer process in annular turbulent gas flow for constant wall temperature

    International Nuclear Information System (INIS)

    Groshev, A.I.; Anisimov, V.V.; Kashcheev, V.M.; Khudasko, V.V.; Yur'ev, Yu.S.

    1987-01-01

    The effect of wall material on convective heat transfer of turbulent gas flow in an annular tube with account of longitudinal diffusion both in the wall and in the liquid is studied numerically. The conjugated problem is solved for P r =0.7 (Re=10 4 -10 6 ). Based on numerical calculations it is stated that thermal conductivity of the wall and gas essentially affects the degree of preliminary heating of liquid in the range of a non-heated section

  11. A gas chromatography-thermal conductivity detection method for helium detection in postmortem blood and tissue specimens.

    Science.gov (United States)

    Schaff, Jason E; Karas, Roman P; Marinetti, Laureen

    2012-03-01

    In cases of death by inert gas asphyxiation, it can be difficult to obtain toxicological evidence supporting assignment of a cause of death. Because of its low mass and high diffusivity, and its common use as a carrier gas, helium presents a particular challenge in this respect. We describe a rapid and simple gas chromatography-thermal conductivity detection method to qualitatively screen a variety of postmortem biological specimens for the presence of helium. Application of this method is demonstrated with three case examples, encompassing an array of different biological matrices.

  12. Self-assembly of conducting polymer nanowires at air-water interface and its application for gas sensors

    International Nuclear Information System (INIS)

    Xu Jianhua; Jiang Yadong; Yang Yajie; Yu Junsheng

    2009-01-01

    Conducting polymer poly (3, 4-ethylenedioxythiophene) (PEDOT) nanowires were prepared by wetting Al 2 O 3 membrane (AAO) template method, which could be well dispersed in organic solvent with ultrasonic treatment. In order to obtain highly ordered structure of nanowires, the self-assembly film of nanowires at air/water interface was investigated by Langmuir-Blodgett (LB) technique. The results showed that PEDOT nanowire-surfactant complex at air/water interface had well self-assembly capability, and the stable float layer was formed with collapse pressure more than 50 mN/m. This well arranged nanowire film was transferred onto interdigitated electrode successfully as novel gas sensing layer through a vertical dipping method. The as-prepared PEDOT nanowire gas sensor was applied to the precise detection of NH 3 and HCl gas, especially for low gas concentration (lower than 5 ppm), and showed higher gas sensitivity than conventional nanowire gas sensor. The chemical sensors based on ordered PEDOT nanowires presented good reversibility and reproducibility in response. Notably, our work presents an appropriate methodology for fabricating ordered conducting polymer nanomaterial for gas sensor and other applications

  13. Rapid gas chromatographic method for the determination of famoxadone, trifloxystrobin and fenhexamid residues in tomato, grape and wine samples.

    Science.gov (United States)

    Likas, D T; Tsiropoulos, N G; Miliadis, G E

    2007-05-25

    Trifloxystrobin, fenhexamid and famoxadone belong to the generation of fungicides acting against a broad spectrum of fungi and widely used in Integrated Pest Management strategies in different agricultural crops but mainly in viticulture. In the present work, a gas chromatographic (GC) method for their determination was developed and validated on tomato, grape and wine matrices. The method was based on a simple one step liquid-liquid microextraction with cyclohexane/dichloromethane (9+1, v/v) and determination of fungicides by gas chromatography with nitrogen phosphorous (NP-) and electron capture (EC-) detection, and ion trap mass spectrometry (ITMS) for confirmation. The method was validated by recovery experiments, assessment of matrix effect and calculation of the associated uncertainty. Recoveries for GC-NPD and GC-ECD were found in the range of 81-102% with RSD NPD, respectively, depending on the sensitivity of each compound with trifloxystrobin being the most sensitive. The expanded uncertainty, calculated for a sample concentration of 0.10 mg/kg, ranged from 4.8 to 13% for the GC-ECD and from 5.4 to 29% for the GC-NPD. The concentration levels for famoxadone residues found in tomato and grape samples from field experiments were clearly below the EU established MRL values, thus causing no problems in terms of food safety.

  14. Gas chromatographic determination of residual hydrazine and morpholine in boiler feed water and steam condensates

    International Nuclear Information System (INIS)

    Vatsala, S.; Bansal, V.; Tuli, D.K.; Rai, M.M.; Jain, S.K.; Srivastava, S.P.; Bhatnagar, A.K.

    1994-01-01

    Hydrazine, an oxygen scavenger in boiler water, was derivatised to the corresponding acetone azine and determined at the ng ml -1 level by gas chromatography. Morpholine, a corrosion inhibitor used in steam boilers, was estimated either directly (if >2.0 μg ml -1 ) or by quantitative preconcentration (0.1 ng-2.0 μg ml -1 ). To obtain symmetrical peaks for these amines, the column packing was coated with KOH. Use of a nitrogen-specific detector improved accuracy of estimation of hydrazine and morpholine, giving a RSD of 1.9-3.6%. Chromatographic analysis of these amines in boiler feed water and steam condensate samples collected from boilers servicing a pertroleum refinery is described. Environmental safety regulations calls for monitoring of hydrazine and the methods developed can easily be adapted for this purpose. (orig.)

  15. Magnetogasdynamic spherical shock wave in a non-ideal gas under gravitational field with conductive and radiative heat fluxes

    Science.gov (United States)

    Nath, G.; Vishwakarma, J. P.

    2016-11-01

    Similarity solutions are obtained for the flow behind a spherical shock wave in a non-ideal gas under gravitational field with conductive and radiative heat fluxes, in the presence of a spatially decreasing azimuthal magnetic field. The shock wave is driven by a piston moving with time according to power law. The radiation is considered to be of the diffusion type for an optically thick grey gas model and the heat conduction is expressed in terms of Fourier's law for heat conduction. Similarity solutions exist only when the surrounding medium is of constant density. The gas is assumed to have infinite electrical conductivity and to obey a simplified van der Waals equation of state. It is shown that an increase of the gravitational parameter or the Alfven-Mach number or the parameter of the non-idealness of the gas decreases the compressibility of the gas in the flow-field behind the shock, and hence there is a decrease in the shock strength. The pressure and density vanish at the inner surface (piston) and hence a vacuum is formed at the center of symmetry. The shock waves in conducting non-ideal gas under gravitational field with conductive and radiative heat fluxes can be important for description of shocks in supernova explosions, in the study of a flare produced shock in the solar wind, central part of star burst galaxies, nuclear explosion etc. The solutions obtained can be used to interpret measurements carried out by space craft in the solar wind and in neighborhood of the Earth's magnetosphere.

  16. Measurement and evaluation of pumping speed and gas discharge characteristics of titanium getter pump by conductance modulation method

    International Nuclear Information System (INIS)

    Terada, Keiko; Okano, Tatsuo; Tsuji, Hiroshi.

    1989-01-01

    The conductance modulation method is designed to determine the pumping speed from a known conductance. With the method, the intrinsic pumping speed Sp and net pumping speed S * can be determined in a wide range up to near the ultimate pressure. In the present study, the pumping speed and gas discharge rate of a titanium getter pump at 77K are analyzed, and the results are compared with measurements made at room temperature. The pressure in a vacuum chamber depends on the gas load and the pumping speed. The pressure varies from P A to P B as the conductance of the orifice is changed from C A to C B . The ultimate pressure also changes from P AO to P BO . The intrinsic and net pumping speeds can be calculated from P A , P B , P AO and P BO . The major feature of the conductance modulation method is that the intrinsic and net pumping speeds can be determined from a change in the conductance without knowing the sensitivity of the vacuum meter or the flow rate of gas entering the chamber from outside. With this feature, the method is very effective for measuring the balance between the gas discharge and pumping speed near the ultimate pressure. (N.K.)

  17. Variability of matrix effects in liquid and gas chromatography - mass spectrometry analysis of pesticide residues after QuEChERS sample preparation of different food crops

    Science.gov (United States)

    Gas and liquid chromatography (GC and LC) coupled to sophisticated mass spectrometry (MS) instruments are among the most powerful analytical tools currently available to monitor pesticide residues in food, among other applications. However, both GC-MS and LC-MS are susceptible to matrix effects whi...

  18. Estimation of Knudsen diffusion coefficients from tracer experiments conducted with a binary gas system and a porous medium.

    Science.gov (United States)

    Hibi, Yoshihiko; Kashihara, Ayumi

    2018-03-01

    A previous study has reported that Knudsen diffusion coefficients obtained by tracer experiments conducted with a binary gas system and a porous medium are consistently smaller than those obtained by permeability experiments conducted with a single-gas system and a porous medium. To date, however, that study is the only one in which tracer experiments have been conducted with a binary gas system. Therefore, to confirm this difference in Knudsen diffusion coefficients, we used a method we had developed previously to conduct tracer experiments with a binary carbon dioxide-nitrogen gas system and five porous media with permeability coefficients ranging from 10 -13 to 10 -11  m 2 . The results showed that the Knudsen diffusion coefficient of N 2 (D N2 ) (cm 2 /s) was related to the effective permeability coefficient k e (m 2 ) as D N2  = 7.39 × 10 7 k e 0.767 . Thus, the Knudsen diffusion coefficients of N 2 obtained by our tracer experiments were consistently 1/27 of those obtained by permeability experiments conducted with many porous media and air by other researchers. By using an inversion simulation to fit the advection-diffusion equation to the distribution of concentrations at observation points calculated by mathematically solving the equation, we confirmed that the method used to obtain the Knudsen diffusion coefficient in this study yielded accurate values. Moreover, because the Knudsen diffusion coefficient did not differ when columns with two different lengths, 900 and 1500 mm, were used, this column property did not influence the flow of gas in the column. The equation of the dusty gas model already includes obstruction factors for Knudsen diffusion and molecular diffusion, which relate to medium heterogeneity and tortuosity and depend only on the structure of the porous medium. Furthermore, there is no need to take account of any additional correction factor for molecular diffusion except the obstruction factor because molecular diffusion is

  19. Doping and defect structure of mixed-conducting ceramics for gas separation

    Science.gov (United States)

    Zuo, Chendong

    A worldwide energy crisis and increasing environmental concerns are strong incentives for using hydrogen as a sustainable and clean energy source. "Hydrogen economy" has been around since 1970s, but it started to look practicable only in recent years. The trend in the future is to switch from using hydrogen as the basic raw material in the chemical industry to the energy carrier in the transportation and distributed energy industries. To meet the expected rising demand, hydrogen has to be generated in a more cost-effective manner. As one of the most important operation units in the hydrogen production, a high performance hydrogen separation membrane system is essential to the coming hydrogen economy. The project of hydrogen separation membrane based on Mixed ionic and electronic conductor (MIEC) composite was initiated by DoE years ago, and the MIEC membrane has been developed in Argonne National Laboratory (ANL) for several years. The goal at ANL is to develop a dense, ceramic-based MIEC membrane that is highly selective, chemical stable in practical environments at operative temperatures up to ≈900°C, and can separate hydrogen from mixed gases at commercially significant fluxes under industrially relevant operating conditions, without the need for electrodes or electrical circuitry. The effort at ANL initially focused on BCY20 (BaCe0.8Y 0.2O3). BCY20 forms the matrix of ANL-1a and -2a ceramic-metal composite membranes (40-50 vol.% of a metal is dispersed in a ceramic matrix) and its bulk transport properties, including ionic transfer number, ionic and electronic conductivity, and chemical and mechanical stability have been systematically studied. However, exposure to CO2 and H2O-containing atmospheres, as would be present in a practical environment, will degrade the material as it reacts to form insulating barium carbonate (BaCO3 ) and cerium oxide (CeO2). This decomposition greatly limits its applicability in hydrogen separation, despite the promising

  20. Adaptive nitrogen and integrated weed management in conservation agriculture: impacts on agronomic productivity, greenhouse gas emissions, and herbicide residues.

    Science.gov (United States)

    Oyeogbe, Anthony Imoudu; Das, T K; Bhatia, Arti; Singh, Shashi Bala

    2017-04-01

    Increasing nitrogen (N) immobilization and weed interference in the early phase of implementation of conservation agriculture (CA) affects crop yields. Yet, higher fertilizer and herbicide use to improve productivity influences greenhouse gase emissions and herbicide residues. These tradeoffs precipitated a need for adaptive N and integrated weed management in CA-based maize (Zea mays L.)-wheat [Triticum aestivum (L.) emend Fiori & Paol] cropping system in the Indo-Gangetic Plains (IGP) to optimize N availability and reduce weed proliferation. Adaptive N fertilization was based on soil test value and normalized difference vegetation index measurement (NDVM) by GreenSeeker™ technology, while integrated weed management included brown manuring (Sesbania aculeata L. co-culture, killed at 25 days after sowing), herbicide mixture, and weedy check (control, i.e., without weed management). Results indicated that the 'best-adaptive N rate' (i.e., 50% basal + 25% broadcast at 25 days after sowing + supplementary N guided by NDVM) increased maize and wheat grain yields by 20 and 14% (averaged for 2 years), respectively, compared with whole recommended N applied at sowing. Weed management by brown manuring (during maize) and herbicide mixture (during wheat) resulted in 10 and 21% higher grain yields (averaged for 2 years), respectively, over the weedy check. The NDVM in-season N fertilization and brown manuring affected N 2 O and CO 2 emissions, but resulted in improved carbon storage efficiency, while herbicide residuals in soil were significantly lower in the maize season than in wheat cropping. This study concludes that adaptive N and integrated weed management enhance synergy between agronomic productivity, fertilizer and herbicide efficiency, and greenhouse gas mitigation.

  1. Residue analysis of organophosphorus and organochlorine pesticides in fatty matrices by gas chromatography coupled with electron-capture detection.

    Science.gov (United States)

    Park, Jae-Woo; Abd El-Aty, A M; Lee, Myoung-Heon; Song, Sung-Ok; Shim, Jae-Han

    2006-01-01

    A multiresidue method for the simultaneous determination of 22 organochlorine (OCs) and organophosphorus (Ops) pesticides (including isomers and metabolites), representing a wide range of physicochemical properties, was developed in fatty matrices extracted from meat. Pesticides were extracted from samples with acetonitrile/n-hexane (v:v, 1:1). The analytical screening was performed by gas chromatography coupled with electron-capture detection (ECD). The identification of compounds was based on their retention time and on comparison of the primary and secondary ions. The optimized method was validated by determining accuracy (recovery percentages), precision (repeatability and reproducibility), and sensitivity (detection and quantitation limits) from analyses of samples fortified at 38 to 300 ng/g levels. Correlation coefficients for the 22 extracted pesticide standard curves (linear regression analysis, n = 3) ranged from 0.998 to 1.000. Recovery studies from 2 g samples fortified at 3 levels demonstrated that the GC-ECD method provides 64.4-96.0% recovery for all pesticides except 2,4'-DDE (44.6-50.4%), 4,4'-DDE (51.1-57.5%) and 2,4'-DDT (50.0-51.2%). Both repeatability and reproducibility relative standard deviation values were < 20% for all residues. Detection limits ranged from 0.31 to 1.27 ng/g and quantification limits were between 1.04 and 4.25 ng/g. The proposed analytical method may be used as a simple procedure in routine determinations of OCs and Ops in meat. It can also be applied to the determination of pesticide multi-residues in other animal products such as butter and milk.

  2. Determination of pesticide residues in animal origin baby foods by gas chromatography coupled with triple quadrupole mass spectrometry.

    Science.gov (United States)

    Amendola, Graziella; Pelosi, Patrizia; Attard Barbini, Danilo

    2015-01-01

    A simple, fast and multiresidue method for the determination of pesticide residues in baby foods of animal origin has been developed in order to check the compliance with the Maximum Residue Levels (MRLs) set at a general value of 0.01 mg/kg by Commission Directive 2006/125/EC for infant foods. The main classes of organochlorine, organophosphorus and pyrethroid compounds have been considered, which are mainly fat soluble pesticides. The analytical procedure consists in the extraction of baby food samples by acetonitrile (ACN) followed by a clean up using C18 solid-phase extraction column eluted with ACN. The compounds were determined by gas chromatography-triple quadrupole mass spectrometry equipped with a Programmed Temperature Vaporizer (PTV) injection and a backflush system. In order to compensate for matrix effects PTV and matrix matched standard calibrations have been used. The method has been fully validated for 57 pesticides according to the Document SANCO/12571/2013. Accuracy and precision (repeatability) have been studied by recoveries at two spiking levels, the Limit of Quantitation (LOQ) (0.003-0.008 mg/kg) and 10 time greater (0.03-0.08 mg/kg), and the results were in the acceptable range of 70-120% with Relative Standards Deviations (RSD) ≤20%. Selectivity, linearity, LOQ and uncertainty of measurement were also determined for all the compounds. The method has been also applied for the analysis of 18 baby food animal origin samples, bought form the local market in Rome (Italy), and no pesticide in the scope of the method has been found above the MRL or the LOQ.

  3. Analysis Proton Conducting Electrolyte IT-SOFC Hybrid System Exhaust Gas With External Reforming of Biofuel

    Directory of Open Access Journals (Sweden)

    Nizar Amir

    2013-03-01

    Full Text Available In this analysis, a hybrid system containing proton SOFC (P-SOFC combine with micro gas turbine (MGT with biofuel external reforming is investigation to decrease the greenhouse gases problem facing in electrical power plant. The hybrid system consist of a proton solid oxide fuel cell stack, a micro gas turbine, a combustor, compressors, heat exchangers and external reformer. The main operating parameter such as, fuel utilization and steam - carbon ratio is determined in this analysis.

  4. [Determination of propargite, tebuconazole and bromopropylate pesticide residues in Taiwan green jujubes by gas chromatography-tandem mass spectrometry].

    Science.gov (United States)

    Zhang, Qun; Liu, Chunhua; Wu, Nancun; Wu, Xiaofang; Li, Shuhuai

    2014-08-01

    An analytical method was established for the determination of propargite, tebuconazole and bromopropylate in Taiwan green jujubes (Zizyphus mauritiana Lam) by gas chromatography-tandem mass spectrometry (GC-MS/MS). The sample was extracted with acetonitrile from the Taiwan green jujubes after treated with a homogenizer. The organic phase was then separated from water phase by adding NaCl. The extract was further purified on a carbon/ NH2 cartridge with elution solvents of acetonitrile/toluene (3:1, v/v). Finally, the target analytes were separated by a capillary gas chromatographic column SLB-5MS (30 m x 0. 25 mm x 0. 25 μm). A tandem quadrupole mass spectrometer operated in either full scan mode or in MS/MS mode for multiple reaction monitoring (MRM) was used for the qualitative and quantitative analysis of the constituents, respectively. The results showed that the average recoveries of the three pesticides ranged from 75. 8% to 103. 6% with the RSDs of 1. 7%-9. 3% at the spiking levels from 0.01 mg/kg to 0. 50 mg/kg (n= 5). The calibration curves showed good linearity in the range of 0.01-0.50 mg/kg, with the determination coefficients over 0.99 (R2>0.99). The limits of quantification (LOQs) were 0.01 mg/kg for propargite, tebuconazole and bromopropylate in Taiwan green jujubes. The method is available for the determination of propargite, tebuconazole and bromopropylate pesticide residues in Taiwan green jujubes.

  5. Conductive Polymer Synthesis with Single-Crystallinity via a Novel Plasma Polymerization Technique for Gas Sensor Applications

    Directory of Open Access Journals (Sweden)

    Choon-Sang Park

    2016-09-01

    Full Text Available This study proposes a new nanostructured conductive polymer synthesis method that can grow the single-crystalline high-density plasma-polymerized nanoparticle structures by enhancing the sufficient nucleation and fragmentation of the pyrrole monomer using a novel atmospheric pressure plasma jet (APPJ technique. Transmission electron microscopy (TEM, Fourier transform infrared spectroscopy (FT-IR, X-ray photoelectron spectroscopy (XPS, and field emission scanning electron microscopy (FE-SEM results show that the plasma-polymerized pyrrole (pPPy nanoparticles have a fast deposition rate of 0.93 µm·min−1 under a room-temperature process and have single-crystalline characteristics with porous properties. In addition, the single-crystalline high-density pPPy nanoparticle structures were successfully synthesized on the glass, plastic, and interdigitated gas sensor electrode substrates using a novel plasma polymerization technique at room temperature. To check the suitability of the active layer for the fabrication of electrochemical toxic gas sensors, the resistance variations of the pPPy nanoparticles grown on the interdigitated gas sensor electrodes were examined by doping with iodine. As a result, the proposed APPJ device could obtain the high-density and ultra-fast single-crystalline pPPy thin films for various gas sensor applications. This work will contribute to the design of highly sensitive gas sensors adopting the novel plasma-polymerized conductive polymer as new active layer.

  6. Environmental Stress Testing of the Single Sample Cylinder: A Proven Consensus Standard for Internal Gas Analysis (IGA) or Residual Gas Analysis (RGA)

    Science.gov (United States)

    Schuessler, Philipp WH

    2010-01-01

    In August 2008, Schuessler Consulting was contracted by NASA GSFC in support of the NASA Electronic Parts and Packaging (NEPP) program to perform two separate studies on moisture laden air in a stainless steel cylinder that had been designed to become a consensus standard for Test Method 1018. This Test Method was originally released for hybrids under Mil. Std. 883 but was quickly utilized on other microelectronic devices under the auspice of Mil. Std. 750. The cylinder had subsequently been fabricated for the 750 community. It was back-filled with moist air and subsequently analyzed over a period of time under a previous NASA contract. It had been shown that moisture in the 4000 - 5000 ppm range could be analyzed rather precisely with a mass spectrometer, commonly referred to as a Residual Gas Analyzer (RGA). The scope of this study was to ascertain if the composition and precision varied as a function of thermal shock at sub-zero temperatures and whether there was consensus when the standard was submitted to other RGA units. It was demonstrated and published that the consensus standard would yield precise RGA data for moisture within +/- 1% when optimized for a given RGA unit. It has been subsequently shown in this study at Oneida Research Services, that sub-zero storage did not affect that precision when a well-defined protocol for the analysis was followed. The consensus standard was taken to a second facility for analysis where it was found that moisture adsorption on the transfer lines caused precision to drop to +/- 12%. The Single Sample Cylinder (SSC) is a one liter stainless steel cylinder with associated sampling valves and has considerable weight and volume. But this considerable size allows for approximately 300 gas samples of the same composition to be delivered to any RGA unit. Lastly, a smaller cylinder, approximately 75 cc, of a second consensus standard was fabricated and tested with a different mix of fixed gases where moisture was kept in the

  7. Evaluation of Pentachlorophenol Residues in Some Hygienic Papers Prepared from Virgin and Secondary Pulp by Electron Capture Gas Chromatographic Method

    Directory of Open Access Journals (Sweden)

    Behrouz Akbari-adergani

    2016-01-01

    Full Text Available In this study, residual amount of pentachlorophenol (PCP as the most important paper preservative, which is extremely hazardous pollutant, was determined in some tissue papers and napkins. Twenty-five samples of two producing hygienic paper factories prepared from virgin and secondary pulp were analyzed for the presence of trace amount of PCP. The analytical procedure involved direct extraction of PCP from hygienic paper and its determination by gas chromatography with electron capture detection. The statistical results for the analysis of all samples revealed that there were significant differences between mean of PCP in hygienic papers prepared from virgin and secondary pulp (P<0.05. This method gave recoveries of 86-98% for hygienic paper made from virgin pulp and 79-92% for hygienic paper made from secondary pulp. The limit of detection (LOD and limit of quantification (LOQ for PCP were 6.3 and 21.0 mg/kg, respectively. The analytical method has the requisite sensitivity, accuracy, precision and specificity to assay PCP in hygienic papers. This study demonstrates a concern with exposition to PCP considering that hygienic paper is largely consumed in the society.

  8. Residual gas analysis of a cryostat vacuum chamber during the cool down of SST - 1 superconducting magnet field coil

    International Nuclear Information System (INIS)

    Semwal, P.; Joshi, K.S.; Thankey, P.L.; Pathan, F.S.; Raval, D.C.; Patel, R.J.; Pathak, H.A.

    2005-01-01

    One of the most important feature of Steady state Superconducting Tokamak -1 (SST-l) is the Nb-Ti superconducting magnet field coils. The coils will be kept in a high vacuum chamber (Cryostat) and liquid Helium will be flown through it to cool it down to its critical temperature of 4.5K. The coil along with its hydraulics has four types of joints (1) Stainless Steel (S.S.) to Copper (Cu) weld joints (2) S. S. to S. S. weld joints (3) Cu to Cu brazed joints and (4) G-10 to S. S. joints with Sti-cast as the binding material. The joints were leak tested with a Helium mass spectrometer leak detector in vacuum as well as in sniffer mode. However during the cool-down of the coil, these joints may develop leaks. This would deteriorate the vacuum inside the cryostat and coil cool-down would subsequently become more difficult. To study the effect of cooling on the vacuum condition of the Cryostat, a dummy Cryostat chamber was fabricated and a toroidal Field (TF) magnet was kept inside this chamber and cooled down to 4.5 K.A residual gas analyzer (RGA) was connected to the Cryostat chamber to study the behaviour of major gases inside this chamber with temperature. An analysis of the RGA data acquired during the coo-down has been presented in this chamber. (author)

  9. Determination of alkylphenolic residues in fresh fruits and vegetables by extractive steam distillation and gas chromatography-mass spectrometry.

    Science.gov (United States)

    Yang, Deng-Kai; Ding, Wang-Hsien

    2005-09-23

    This study describes a simple and sensitive method for determining the alkylphenolic compounds, 4-tert-octylphenol (4-t-OP), 4-nonylphenol isomers (4-NPs), and their monoethoxylates (4-t-OP1EO and 4-NP1EOs), in fresh fruits and vegetables. The method involves extracting a sample by a modified Nielson-Kryger steam distillation extraction using n-hexane for 1 h. The alkylphenolic compounds were identified and quantitated by gas chromatography-mass spectrometry (GC-MS) in selected ion monitoring (SIM) mode. Various pH values and amounts of NaCl added to the sample solution were evaluated as extraction conditions. The quantitation limit of this method was less than 0.2 ng/g in 10 g (fresh weight) of sample. Recovery of alkylphenolic compounds in spiked samples exceeded 64% while R.S.D. ranged from 1.0 to 9.8%. Alkylphenolic residues were detected in fresh fruits and vegetables at concentrations of 4-NPs and 4-t-OP from n.d. to 16 ng/g and from n.d. to 4.8 ng/g (fresh weight), respectively. NP1EO and OP1EO were always below the quantitation limit.

  10. Determination of alkylphenol residues in baby-food purees by steam distillation extraction and gas chromatography-mass spectrometry.

    Science.gov (United States)

    Li, Chia-Tien; Cheng, Chin-Yuan; Ding, Wang-Hsien

    2008-02-01

    This paper describes a simple and sensitive method for determining alkylphenols namely 4-tert-octylphenol (4-t-OP) and the isomers of 4-nonylphenol (4-NPs) present in various types of baby-food purees. The method involves extracting a sample with n-hexane for 1h using a modified Nielson-Kryger steam distillation extraction system and then identifying and quantitating the alkylphenols using a gas chromatography-mass spectrometry (GC-MS) operated in the selected ion monitoring (SIM) mode. The extraction conditions were evaluated at various values of pH of the sample solution. The limits of quantitation for this method were 0.2 ng/g from 1.0 g (wet weight) samples of 4-t-OP and the 4-NPs. The intra- and interbatch precisions and accuracies were also determined. The precision, in terms of the relative standard deviation (RSD), were less than 8%. Most of the recoveries of the alkylphenols from various spiked samples exceeded 60%, while the values of RSD ranged from 1% to 10%. Alkylphenol residues were detected in baby-food purees at concentrations of up to 19 ng/g (wet weight) for 4-t-OP and up to 21 ng/g (wet weight) for the 4-NPs.

  11. A conserved residue, PomB-F22, in the transmembrane segment of the flagellar stator complex, has a critical role in conducting ions and generating torque.

    Science.gov (United States)

    Terauchi, Takashi; Terashima, Hiroyuki; Kojima, Seiji; Homma, Michio

    2011-08-01

    Bacterial flagellar motors exploit the electrochemical potential gradient of a coupling ion (H(+) or Na(+)) as their energy source, and are composed of stator and rotor proteins. Sodium-driven and proton-driven motors have the stator proteins PomA and PomB or MotA and MotB, respectively, which interact with each other in their transmembrane (TM) regions to form an ion channel. The single TM region of PomB or MotB, which forms the ion-conduction pathway together with TM3 and TM4 of PomA or MotA, respectively, has a highly conserved aspartate residue that is the ion binding site and is essential for rotation. To investigate the ion conductivity and selectivity of the Na(+)-driven PomA/PomB stator complex, we replaced conserved residues predicted to be near the conserved aspartate with H(+)-type residues, PomA-N194Y, PomB-F22Y and/or PomB-S27T. Motility analysis revealed that the ion specificity was not changed by either of the PomB mutations. PomB-F22Y required a higher concentration of Na(+) to exhibit swimming, but this effect was suppressed by additional mutations, PomA-N194Y or PomB-S27T. Moreover, the motility of the PomB-F22Y mutant was resistant to phenamil, a specific inhibitor for the Na(+) channel. When PomB-F22 was changed to other amino acids and the effects on swimming ability were investigated, replacement with a hydrophilic residue decreased the maximum swimming speed and conferred strong resistance to phenamil. From these results, we speculate that the Na(+) flux is reduced by the PomB-F22Y mutation, and that PomB-F22 is important for the effective release of Na(+) from PomB-D24.

  12. Different Analytical Procedures for the Study of Organic Residues in Archeological Ceramic Samples with the Use of Gas Chromatography-mass Spectrometry.

    Science.gov (United States)

    Kałużna-Czaplińska, Joanna; Rosiak, Angelina; Kwapińska, Marzena; Kwapiński, Witold

    2016-01-01

    The analysis of the composition of organic residues present in pottery is an important source of information for historians and archeologists. Chemical characterization of the materials provides information on diets, habits, technologies, and original use of the vessels. This review presents the problem of analytical studies of archeological materials with a special emphasis on organic residues. Current methods used in the determination of different organic compounds in archeological ceramics are presented. Particular attention is paid to the procedures of analysis of archeological ceramic samples used before gas chromatography-mass spectrometry. Advantages and disadvantages of different extraction methods and application of proper quality assurance/quality control procedures are discussed.

  13. Residual radioactive contamination of the Monte Bello Islands from nuclear weapons tests conducted in 1952 and 1956

    International Nuclear Information System (INIS)

    Cooper, M.B.

    1979-04-01

    Distributions of long-lived radionuclides remaining from nuclear weapons trials conducted at the Monte Bello Islands in 1952 and 1956 are presented. These data are derived from a field survey carried out in 1978 and augmented with earlier data from a survey in 1972

  14. The hydraulic conductance of Fraxinus ornus leaves is constrained by soil water availability and coordinated with gas exchange rates.

    Science.gov (United States)

    Gortan, Emmanuelle; Nardini, Andrea; Gascó, Antonio; Salleo, Sebastiano

    2009-04-01

    Leaf hydraulic conductance (Kleaf) is known to be an important determinant of plant gas exchange and photosynthesis. Little is known about the long-term impact of different environmental factors on the hydraulic construction of leaves and its eventual consequences on leaf gas exchange. In this study, we investigate the impact of soil water availability on Kleaf of Fraxinus ornus L. as well as the influence of Kleaf on gas exchange rates and plant water status. With this aim, Kleaf, leaf conductance to water vapour (gL), leaf water potential (Psileaf) and leaf mass per area (LMA) were measured in F. ornus trees, growing in 21 different sites with contrasting water availability. Plants growing in arid sites had lower Kleaf, gL and Psileaf than those growing in sites with higher water availability. On the contrary, LMA was similar in the two groups. The Kleaf values recorded in sites with two different levels of soil water availability were constantly different from each other regardless of the amount of precipitation recorded over 20 days before measurements. Moreover, Kleaf was correlated with gL values. Our data suggest that down-regulation of Kleaf is a component of adaptation of plants to drought-prone habitats. Low Kleaf implies reduced gas exchange which may, in turn, influence the climatic conditions on a local/regional scale. It is concluded that leaf hydraulics and its changes in response to resource availability should receive greater attention in studies aimed at modelling biosphere-atmosphere interactions.

  15. EFFECTS OF TRITIUM GAS EXPOSURE ON THE GLASS TRANSITION TEMPERATURE OF EPDM ELASTOMER AND ON THE CONDUCTIVITY OF POLYANILINE

    Energy Technology Data Exchange (ETDEWEB)

    Clark, E; Marie Kane, M

    2008-12-12

    Four formulations of EPDM (ethylene-propylene diene monomer) elastomer were exposed to tritium gas initially at one atmosphere and ambient temperature for between three and four months in closed containers. Material properties that were characterized include density, volume, mass, appearance, flexibility, and dynamic mechanical properties. The glass transition temperature was determined by analysis of the dynamic mechanical property data per ASTM standards. EPDM samples released significant amounts of gas when exposed to tritium, and the glass transition temperature increased by about 3 C. during the exposure. Effects of ultraviolet and gamma irradiation on the surface electrical conductivity of two types of polyaniline films are also documented as complementary results to planned tritium exposures. Future work will determine the effects of tritium gas exposure on the electrical conductivity of polyaniline films, to demonstrate whether such films can be used as a sensor to detect tritium. Surface conductivity was significantly reduced by irradiation with both gamma rays and ultraviolet light. The results of the gamma and UV experiments will be correlated with the tritium exposure results.

  16. Vacuum stability and residual gas density estimation for the vacuum chamber upgrade of the ATLAS interaction region of the Large Hadron Collider

    CERN Document Server

    Bregliozzi, G; Baglin, V; Jimenez, J M

    2012-01-01

    The CERN Large Hadron Collider (LHC) has 54 km of ultra-high vacuum (UHV) beam chambers out of which about 90% are at cryogenic temperature (1.9 K) and the rest at room temperature. During operation, the residual gas density in the beam pipes is dominated by beam induced effect such ion, electron and photon-stimulated gas desorption. Therefore, the computation of gas density profile is of great importance to confirm the vacuum stability, and to estimate the beam lifetime. Moreover, the gas density profiles are essential to determine the machine induced background in the experimental areas, and to define the pressure profile in the cryogenic sectors where there is no vacuum instrumentation available. In this paper, the vacuum stability is studied for a newly proposed upgrade of the vacuum chamber at the ATLAS interaction point, using the vacuum stability code called VASCO. The residual gas density profile along the ATLAS vacuum chambers and the effects of photon and electron flux hitting the vacuum chamber wal...

  17. Thin film electronic devices with conductive and transparent gas and moisture permeation barriers

    Energy Technology Data Exchange (ETDEWEB)

    Simpson, Lin Jay

    2015-07-28

    Thin film electronic devices (or stacks integrated with a substrate) that include a permeation barrier formed of a thin layer of metal that provides a light transmitting and electrically conductive layer, wherein the electrical conductive layer is formed on a surface of the substrate or device layer such as a transparent conducting material layer with pin holes or defects caused by manufacturing and the thin layer of metal is deposited on the conductive layer and formed from a self-healing metal that forms self-terminating oxides. A permeation plug or block is formed in or adjacent to the thin film of metal at or proximate to the pin holes to block further permeation of contaminants through the pin holes.

  18. The defect level and ideal thermal conductivity of graphene uncovered by residual thermal reffusivity at the 0 K limit.

    Science.gov (United States)

    Xie, Yangsu; Xu, Zaoli; Xu, Shen; Cheng, Zhe; Hashemi, Nastaran; Deng, Cheng; Wang, Xinwei

    2015-06-14

    Due to its intriguing thermal and electrical properties, graphene has been widely studied for potential applications in sensor and energy devices. However, the reported value for its thermal conductivity spans from dozens to thousands of W m(-1) K(-1) due to different levels of alternations and defects in graphene samples. In this work, the thermal diffusivity of suspended four-layered graphene foam (GF) is characterized from room temperature (RT) down to 17 K. For the first time, we identify the defect level in graphene by evaluating the inverse of thermal diffusivity (termed "thermal reffusivity": Θ) at the 0 K limit. By using the Debye model of Θ = Θ0 + C× e(-θ/2T) and fitting the Θ-T curve to the point of T = 0 K, we identify the defect level (Θ0) and determine the Debye temperature of graphene. Θ0 is found to be 1878 s m(-2) for the studied GF and 43-112 s m(-2) for three highly crystalline graphite materials. This uncovers a 16-43-fold higher defect level in GF than that in pyrolytic graphite. In GF, the phonon mean free path solely induced by defects and boundary scattering is determined as 166 nm. The Debye temperature of graphene is determined to be 1813 K, which is very close to the average theoretical Debye temperature (1911 K) of the three acoustic phonon modes in graphene. By subtracting the defect effect, we report the ideal thermal diffusivity and conductivity (κideal) of graphene presented in the 3D foam structure in the range of 33-299 K. Detailed physics based on chemical composition and structure analysis are given to explain the κideal-T profile by comparing with those reported for suspended graphene.

  19. Analysis of residual crosslinking agent content in UV cross-linked poly(ethylene oxide hydrogels for dermatological application by gas chromatography

    Directory of Open Access Journals (Sweden)

    Rachel Shet Hui Wong

    2016-10-01

    Full Text Available Acrylates have been widely used in the synthesis of pharmaceutical polymers. The quantitation of residual acrylate monomers is vital as they are strong irritants and allergens, but after polymerization, are relatively inert, causing no irritation and allergies. Poly(ethylene oxide (PEO hydrogels were prepared using pentaerythritol tetra-acrylate (PETRA as UV crosslinking agent. A simple, accurate, and robust quantitation method was developed based on gas chromatographic techniques (GC, which is suitable for routine analysis of residual PETRA monomers in these hydrogels. Unreacted PETRA was initially identified using gas chromatography–mass spectrometry (GC–MS. The quantitation of analyte was performed and validated using gas chromatography equipped with a flame ionization detector (GC–FID. A linear relationship was obtained over the range of 0.0002%–0.0450% (m/m with a correlation coefficient (r2 greater than 0.99. The recovery (>90%, intra-day precision (%RSD <0.67, inter-day precision (%RSD <2.5%, and robustness (%RSD <1.62% of the method were within the acceptable values. The limit of detection (LOD and limit of quantitation (LOQ were 0.0001% (m/m and 0.0002% (m/m, respectively. This assay provides a simple and quick way of screening for residual acrylate monomer in hydrogels.

  20. Gas Diffusion-Derived Tortuosity Governs Saturated Hydraulic Conductivity in Sandy Soils

    DEFF Research Database (Denmark)

    Masís-Meléndez, F.; Chamindu, Deepagoda; de Jonge, Lis Wollesen

    2014-01-01

    Accurate prediction of saturated hydraulic conductivity (Ksat) is essential for the development of better distributed hydrological models and area-differentiated risk assessment of chemical leaching. The saturated hydraulic conductivity is often estimated from basic soil properties such as particle......, potential relationships between Ksat and Dp/Do were investigated. A total of 84 undisturbed soil cores were extracted from the topsoil of a field site, and Dp/Do and Ksat were measured in the laboratory. Water-induced and solids-induced tortuosity factors were obtained by applying a two-parameter Dp....../Do model to measured data, and subsequently linked to the cementation exponent of the wellestablished Revil and Cathles predictive model for saturated hydraulic conductivity. Furthermore, a two-parameter model, analogue to the Kozeny-Carman equation, was developed for the Ksat - Dp/Do relationships. All 44...

  1. Computational fluid dynamics (CFD) analysis of the combustion process of a leather residuals gasification fuel gas: influence of fuel moisture content

    Energy Technology Data Exchange (ETDEWEB)

    Antonietti, Anderson Jose; Beskow, Arthur Bortolin; Silva, Cristiano Vitorino da [Universidade Regional Integrada do Alto Uruguai e das Missoes (URI), Erechim, RS (Brazil)], E-mails: arthur@uricer.edu.br, mlsperb@unisinos.br; Indrusiak, Maria Luiza Sperb [Universidade do Vale do Rio dos Sinos (UNISINOS), Sao Leopoldo, RS (Brazil)], E-mail: cristiano@uricer.edu.br

    2010-07-01

    This work presents a numerical study of the combustion process of leather residuals gasification gas, aiming the improvement of the process efficiency, considering different concentrations of water on the gas. The heating produced in this combustion process can be used to generation of thermal and/or electrical energy, for use at the leather industrial plant. However, the direct burning of this leather-residual-gas into the chambers is not straightforward. The alternative in development consists in processing this leather residuals by gasification or pyrolysis, separating the volatiles and products of incomplete combustion, for after use as fuel in a boiler. At these processes, different quantities of water can be used, resulting at different levels of moisture content in this fuel gas. This humidity can affect significantly the burning of this fuel, producing unburnt gases, as the carbon monoxide, or toxic gases as NOx, which must have their production minimized on the process, with the purpose of reducing the emission of pollutants to the atmosphere. Other environment-harmful-gases, remaining of the chemical treatment employed at leather manufacture, as cyanide, and hydrocarbons as toluene, must burn too, and the moisture content has influence on it. At this way, to increase understanding of the influence of moisture in the combustion process, it was made a numerical investigation study of reacting flow in the furnace, evaluating the temperature field, the chemical species concentration fields, flow mechanics and heat transfer at the process. The commercial CFD code CFX Ansys Inc. was used. Considering different moisture contents in the fuel used on the combustion process, with this study was possible to achieve the most efficient burning operation parameters, with improvement of combustion efficiency, and reduction of environmental harmful gases emissions. It was verified that the different moisture contents in the fuel gas demand different operation conditions

  2. Standard test method for conducting erosion tests by solid particle impingement using gas jets

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2007-01-01

    1.1 This test method covers the determination of material loss by gas-entrained solid particle impingement erosion with jetnozzle type erosion equipment. This test method may be used in the laboratory to measure the solid particle erosion of different materials and has been used as a screening test for ranking solid particle erosion rates of materials in simulated service environments (1,2 ). Actual erosion service involves particle sizes, velocities, attack angles, environments, and so forth, that will vary over a wide range (3-5). Hence, any single laboratory test may not be sufficient to evaluate expected service performance. This test method describes one well characterized procedure for solid particle impingement erosion measurement for which interlaboratory test results are available. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determi...

  3. Characterisation of polycyclic aromatic hydrocarbons in flue gas and residues of a full scale fluidized bed combustor combusting non-hazardous industrial waste.

    Science.gov (United States)

    Van Caneghem, J; Vandecasteele, C

    2014-11-01

    This paper studies the fate of PAHs in full scale incinerators by analysing the concentration of the 16 EPA-PAHs in both the input waste and all the outputs of a full scale Fluidized Bed Combustor (FBC). Of the analysed waste inputs i.e. Waste Water Treatment (WWT) sludge, Refuse Derived Fuel (RDF) and Automotive Shredder Residue (ASR), RDF and ASR were the main PAH sources, with phenanthrene, fluoranthene and pyrene being the most important PAHs. In the flue gas sampled at the stack, naphthalene was the only predominant PAH, indicating that the PAHs in FBC's combustion gas were newly formed and did not remain from the input waste. Of the other outputs, the boiler and fly ash contained no detectable levels of PAHs, whereas the flue gas cleaning residue contained only low concentrations of naphthalene, probably adsorbed from the flue gas. The PAH fingerprint of the bottom ash corresponded rather well to the PAH fingerprint of the RDF and ASR, indicating that the PAHs in this output, in contrast to the other outputs, were mainly remainders from the PAHs in the waste inputs. A PAH mass balance showed that the total PAH input/output ratio of the FBC ranged from about 100 to about 2600 depending on the waste input composition and the obtained combustion conditions. In all cases, the FBC was clearly a net PAH sink. Copyright © 2014 Elsevier Ltd. All rights reserved.

  4. Development, manufacturing and testing of a gas-loaded variable conductance methanol heat pipe

    Science.gov (United States)

    Vanbuggenum, R. I. J.; Daniels, D. H. W.

    1987-02-01

    The experimental technology required to measure the performance of moderate temperature heat pipes is presented. The heat pipe manufacturing process is described. The hydrodynamic characteristics of the porous structure inside the heat pipe envelope were examined using a specially developed test rig, based upon a steady-state evaporation test. A fully automated test facility was developed and validated by testing constant conductance and variable conductance heat pipes (VCHP). Theoretical performance predictions are illustrated in terms of pressure, depicted in 3D-plots, and compared with the test results of the heat pipe performance tests. The design of the VCHP was directed towards the verification of the VCHP mathematical model. The VCHP design is validated and ready for the final testing and model verification.

  5. Biochemical effects of manufactured gas plant residue following ingestion by B6C3F1 mice

    Energy Technology Data Exchange (ETDEWEB)

    Weyand, E.H.; Wu, Yun; Patel, S. (State Univ. of New Jersey, Piscataway, NJ (United States)); Goldstein, L. (Electric Power Research Institute, Palto Alto, CA (United States))

    1994-01-01

    The toxic potential of manufactured gas plant residue (MGP) given in the diet to male and female B6C3F1 mice was evaluated. In addition, the bioavailability of chemical components of MGP were also investigated by monitoring polycyclic aromatic hydrocarbon (PAH) metabolites in urine and DNA adduct formation in forestomach and lung tissue. Basal gel diets containing 0.05, 0.25, 0.50% benzo[a]pyrene (BaP) were fed to animals for 94 and 185 d. Mice readily consumed adulterated diets without any evidence of acute toxicity. The total amount of MGP and BaP consumed by mice ranged from 118 to 2604 mg and from 12 to 29 mg, respectively. Male mice fed a control or BaP diet and female mice fed a 0.05% MGP diet had the highest body weight gains. Male and female mice fed a 0.50% MGP diet had the lowest body weight gains. the bioavailability of chemical components of MGP was evaluated by monitoring the urinary excretion of PAH metabolites by male mice fed a 0.25% MGP diet. 1-Hydroxypyrene was determined by high-performance liquid chromatography analysis to be the major fluorescent metabolite excreted by mice throughout the 185 d of diet administration. At necropsy, no chemical-related gross lesions were detected. In addition, no treatment-related microscopic lesions were evident in tissues obtained from animals fed a 0.50% MGP- or BaP-adulterated diet. The [sup 32]P-postlabeling assay was used to evaluate MGP- and BaP-induced DNA adduct formation in lung and forestomach tissue. The level of DNA adducts formed from the chemical components of MGP paralleled the amount of material ingested by animals. Lung DNA adduct levels were considerably higher than forestomach levels when mice ingested a 0.25% or 0.50% MGP diet. These studies demonstrate that the continuous ingestion of MGP or BaP for 185 d does not result in acute toxicity or chemical-related lesions at doses up to 0.50% MGP or 0.005% BaP. 36 refs., 3 figs., 4 tabs.

  6. Tritium Sequestration in Gen IV NGNP Gas Stream via Proton Conducting Ceramic Pumps

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Fanglin Frank [Univ. of South Carolina, Columbia, SC (United States); Adams, Thad M. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Brinkman, Kyle [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Reifsnider, Kenneth [Univ. of South Carolina, Columbia, SC (United States)

    2011-09-30

    Several types of high-temperature proton conductors based on SrCeO3 and BaCeO3 have been systematically investigated in this project for tritium separation in NGNP applications. One obstacle for the field application is the chemical stability issues in the presence of steam and CO2 for these proton conductors. Several strategies to overcome such issues have been evaluated, including A site doping and B site co-doping method for perovskite-structured proton conductors. Novel zirconium-free proton conductors have also been developed with improved electrical conductivity and enhanced chemical stability. Novel catalytic materials for the proton-conducting separation membranes have been investigated. A tubular geometry proton-conducting membrane has been developed for the proton separation membranes. Total dose rate estimated from tritium decay (beta emission) under realistic membrane operating conditions, combined with electron irradiation experiments, indicates that proton ceramic materials possess the appropriate radiation stability for this application.

  7. [Design of amplifier circuit for thermal conductivity detector in micro gas chromatography].

    Science.gov (United States)

    Liu, Hongfei; Chen, Zhong

    2010-08-01

    Agilent 3000 + is a typical micro gas chromatograph (micro GC) which is widely used for its fast analysis, high resolution, wide dynamic range and energy-efficient. However its amplifier circuit and analog-to-digital convertor (ADC) are of high power consumption and high working temperature. Based on the results of theoretical calculation, ADS1255, a 24-bit delta-sigma ADC from TI, was selected as the core component for its low noise and energy-efficient. Furthermore, a low noise, high common-mode voltage durable full differential amplifier circuit was designed to accomplish the functions of impedance matching, filtering, and level shifting in front of ADC. The full differential amplifier was optimized with the analysis of noise model and theoretical calculation. In addition, a testing platform was developed to test the full differential amplifier and ADC. The testing results showed that the American Society for Testing and Materials (ASTM) noise value of new full different amplifier and ADC was as low as 1.25 microV and the power dissipation was 3.7 W lower than that of the old circuit. The new circuit is low noise, energy-efficient, compact and cheap and can cater for the requirement of the micro GC of next generation.

  8. Numerical study of the viscous heat-conducting gas flow in a long shock tube

    Science.gov (United States)

    Kudryavtsev, Alexey; Khotyanovsky, Dmitry

    2017-10-01

    The results of numerical simulations of the propagation of the shock wave in a cylindrical shock tube of large length are presented. The results of the numerical computations agree well with the experimental data of Duff. The effects of viscous friction and heat conduction cause significant difference of the shock wave velocity from its inviscid theoretical value. The results of the computations at the considered flow parameters show that the shock wave and the contact surface, starting from a certain moment of time, propagate with equal speeds.

  9. Tritium Sequestration in Gen IV NGNP Gas Stream via Proton Conducting Ceramic Pumps

    International Nuclear Information System (INIS)

    Chen, Franglin Frank; Adams, Thad M.; Brinkman, Kyle; Reifsnider, Kenneth

    2011-01-01

    Several perovskite structured proton conductors based on SrCeO 3 and BaCeO 3 have been investigated in the project. The solid solutions for SrCeO 3 and BaCeO 3 were first investigated. The morphological and electrical properties of Ba 1-x Sr x Ce 0.8 Y 0.2 O 3-δ with x varying from 0 to 1 prepared by a modified Pechini method were investigated as potential high temperature proton conductors. Dense microstructures were achieved for all the samples upon sintering at 1500ees)C for 5 h. The phase structure analysis indicated that perovskite phase was formed for 0≤x≤0.2, while for x larger than 0.5, impurity phases of Sr 2 CeO 4 and Y 2 O 3 appeared. The stability tests indicated that the resistance to boiling water for Ba 1-x Sr x Ce 0.8 Y 0.2 O 3-δ was between that of BaCe 0.8 Y 0.2 O 3-δ and SrCe 0.8 Y 0.2 O 3-δ Due to the tendency of the reaction with CO 2 for both BaCe 0.8 Y 0.2 O 3-δ and SrCe 0.8 Y 0.2 O 3-δ , it was not surprising that Ba 1-x Sr x Ce 0.8 Y 0.2 O 3-δ was also not stable in CO 2 containing atmospheres. The conductivity tests indicated that Ba 1-x Sr x Ce 0.8 Y 0.2 O 3-δ possessed the electrical conductivity between BaCe 0.8 Y 0.2 O 3-δ and SrCe 0.8 Y 0.2 O 3-δ . The conductivity decreased and the activation energy increased with the increase in Sr content in Ba 1-x Sr x Ce 0.8 Y 0.2 O 3-δ .

  10. Thin film electronic devices with conductive and transparent gas and moisture permeation barriers

    Energy Technology Data Exchange (ETDEWEB)

    Simpson, Lin Jay

    2013-12-17

    A thin film stack (100, 200) is provided for use in electronic devices such as photovoltaic devices. The stack (100, 200) may be integrated with a substrate (110) such as a light transmitting/transmissive layer. A electrical conductor layer (120, 220) is formed on a surface of the substrate (110) or device layer such as a transparent conducting (TC) material layer (120,220) with pin holes or defects (224) caused by manufacturing. The stack (100) includes a thin film (130, 230) of metal that acts as a barrier for environmental contaminants (226, 228). The metal thin film (130,230) is deposited on the conductor layer (120, 220) and formed from a self-healing metal such as a metal that forms self-terminating oxides. A permeation plug or block (236) is formed in or adjacent to the thin film (130, 230) of metal at or proximate to the pin holes (224) to block further permeation of contaminants through the pin holes (224).

  11. Decision in the matter of a generic hearing in respect to market issues and conduct related to the sale of gas and customer services in the natural gas industry in New Brunswick

    International Nuclear Information System (INIS)

    2003-01-01

    In response to changes in the Gas Distribution Act and the Gas Distributor Marketing Regulation, the New Brunswick Board of Commissioners of Public Utilities (Board), issued an order in June 2003 for a generic hearing regarding the sale of gas and customer services in the natural gas industry in New Brunswick. The purpose of the hearing was to have an open discussion among intervenors regarding several issues, such as whether the Code of Conduct provides fair and adequate rules for marketers; should Enbridge Gas New Brunswick (EGNB) be required to follow rules similar to the Code of Conduct; the requirements surrounding letters of credit; the Board's decision on Rules and Regulations regarding the billing conduct of gas distributors and marketers; the information that should be provided by a gas marketer or a distributor to the customer before the customer enters into an agreement for the supply of gas; the need for information on price volatility; the need for EGNB to notify potential customers of all possible suppliers of gas; the removal of automatic renewal clauses from gas retailers' contracts; how the Board should determine if prices are reasonably and sufficiently competitive; financial reporting requirements; the role of the Board in response to customer complaints regarding the sale of gas by a distributor; and, the Board's action regarding Enbridge Atlantic's plan to exit the New Brunswick market. This report provided the response to these issues by 10 intervenors

  12. Fuel gas production from animal and agricultural residues and biomass. Quarterly coordination meeting, December 11-12, 1978, Denver, Colorado. Second Quarterly progress report

    Energy Technology Data Exchange (ETDEWEB)

    Wise, D L; Ashare, E; Wentworth, R L

    1979-01-05

    The tenth quarterly coordination meeting of the methane production group of the Fuels from Biomass Systems Branch, US Department of Energy was held at Denver, Colorado, December 11-12, 1978. Progress reports were presented by the contractors and a site visit was made to the Solar Energy Research Institute, Golden, Colorado. A meeting agenda, a list of attendees, and progress are presented. Report titles are: pipeline fuel gas from an environmental feedlot; operation of a 50,000 gallon anaerobic digester at the Monroe State Dairy Farm near Monroe, Washington; anaerobic fermentation of livestock and crop residues; anaerobic fermentation of agricultural residues - potential for improvement and implementation; heat treatment of organics for increasing anaerobic biodegradability; and biological conversion of biomass to methane. (DC)

  13. Influence of soil organic C content on the greenhouse gas emission potential after application of biogas residues or cattle slurry - Results from a pot experiment

    Science.gov (United States)

    Heintze, Gawan

    2017-04-01

    Influence of soil organic C content on the greenhouse gas emission potential after application of biogas residues or cattle slurry - Results from a pot experiment Gawan Heintze1,2, Tim Eickenscheidt1, Urs Schmidthalter2 and Matthias Drösler1 1University of Applied Sciences Weihenstephan-Triesdorf, Chair of Vegetation Ecology, Weihenstephaner Berg 4, 85354 Freising, Germany 2Technische Universität München, Chair of Plant Nutrition, Emil-Ramann-Str. 2, 85354 Freising, Germany The European Union Renewable Energy Directive, which sets a binding target of a final energy consumption of 20% from renewable sources by 2020, has markedly promoted the increase of biogas plants, particularly in Germany. As a consequence, a large amount of biogas residue remains as a by-product of the fermentative process. These residues are now widely used instead of mineral fertilizers or animal slurries to maintain soil fertility and productivity. However, to date, the effect of the application of biogas residue on greenhouse gas (GHG) emission, compared to that of other organic fertilizers, is contradictory in literature, not having been completely understood. It is often stated that GHG fluxes are closely related to the quality of the raw material, particularly the type of soil to which the digestates are applied. This study addresses the questions (a) to what extent are the applications of biogas digestate and cattle slurry different in terms of their GHG emission (CO2, CH4 and N2O) potential, and (b) how do different soil organic carbon contents (SOCs) influence the rate of GHG exchange. We hypothesize that, i) cattle slurry application enhances the CO2 and N2O fluxes compared to the biogas digestate due to the overall higher C and N input, and ii) that with increasing SOC and N content, higher emissions of CO2 and N2O can be expected. The study was conducted as a pot experiment. Biogas digestate and cattle slurry were applied to and incorporated into three different soil types with

  14. Development of proton conducting materials and membranes based on lanthanum tungstate for hydrogen separation from gas mixtures

    International Nuclear Information System (INIS)

    Seeger, Janka

    2013-01-01

    Lanthanum tungstate La 6-x WO 12-δ (named LWO) is a ceramic material with mixed protonic electronic conductivity. Thereby it is a good candidate membrane material for hydrogen separation from synthesis gas in a fossil pre-combustion power plant. This work shows a material optimization by substitution targeted to clearly enhance the mixed conductivity and thereby the hydrogen flow through the LWO membrane. The first part of the work shows the synthesis and characterization of unsubstituted LWO. It points out that monophase LWO powder can be reproducibly synthesized. The La/W-ratio has to be considerably smaller than the nominal ratio of La/W = 6.0. It also depends on the used sintering conditions. Different relevant properties of LWO like stability in conditions close to application, thermal expansion, sintering behavior or microstructure were determined. Furthermore, the electrical conductivity of the material was investigated. LWO exhibits a prevailing protonic conductivity up to 750 C in wet atmospheres. Under dry atmospheres n-type conductivity was dominating. Oxygen ion and n-type conductivity dominated in wet and dry atmospheres above 750 C. The main part of the work is concerned with the development of new LWO based materials by substitutions. The aim is to achieve an improved mixed protonic electronic conductivity. Substitution elements for lanthanum side were Mg, Ca, Sr, Ba, Ce, Nd, Tb, Y and Al, while for the tungsten side Mo, Re and Ir were used. The total conductivity of the developed materials was investigated and compared to that of the unsubstituted LWO. The substitution of lanthanum led to no appreciable enhancement of the conductivity whereas the substitution of tungsten with 20 mol% molybdenum or 20 mol% rhenium clearly improved it. This caused a hydrogen flow about seven times higher for 20 mol% molybdenum- and about ten times higher for 20 mol% rhenium-substituted LWO in comparison with the unsubstituted LWO at 700 C. In the last part of the

  15. Effect of the Basic Residue on the Energetics, Dynamics and Mechanisms of Gas- Phase Fragmentation of Protonated Peptides

    Energy Technology Data Exchange (ETDEWEB)

    Laskin, Julia; Yang, Zhibo; Song, Tao; Lam, Corey; Chu, Ivan K.

    2010-11-17

    The effect of the basic residue on the energetics, dynamics and mechanisms of backbone fragmentation of protonated peptides was investigated. Time- and collision energy-resolved surface-induced dissociation (SID) of singly protonated peptides with the N-terminal arginine residue and their analogs, in which arginine is replaced with less basic lysine and histidine residues was examined using in a specially configured Fourier transform ion cyclotron resonance mass spectrometer (FT-ICR MS). SID experiments demonstrated very different kinetics of formation of several primary product ions of peptides with and without arginine residue. The energetics and dynamics of these pathways were determined from the RRKM modeling of the experimental data. Comparison between the kinetics and energetics of fragmentation of arginine-containing peptides and the corresponding methyl ester derivatives provides important information on the effect of dissociation pathways involving salt bridge (SB) intermediates on the observed fragmentation behavior. It is found that because pathways involving SB intermediates are characterized by low threshold energies, they efficiently compete with classical oxazolone pathways of arginine-containing peptides on a long timescale of the FT-ICR instrument. In contrast, fragmentation of histidine- and lysine-containing peptides is largely determined by classical oxazolone pathways. Because SB pathways are characterized by negative activation entropies, fragmentation of arginine-containing peptides is kinetically hindered and observed at higher collision energies as compared to their lysine- and histidine-containing analogs.

  16. Analysis of a gas-phase partitioning tracer test conducted in an unsaturated fractured-clay formation.

    Science.gov (United States)

    Simon, Michelle A; Brusseau, Mark L

    2007-03-20

    The gas-phase partitioning tracer method was used to estimate non-aqueous phase liquid (NAPL), water, and air saturations in the vadose zone at a chlorinated-solvent contaminated field site in Tucson, AZ. The tracer test was conducted in a fractured-clay system that is the confining layer for the underlying regional aquifer. Three suites of three tracers were injected into wells located 14, 24, and 24 m from a single, central extraction well. The tracers comprised noble gases (traditionally thought to be nonsorbing), alkanes (primarily water partitioning), perfluorides (primarily NAPL partitioning), and halons (both NAPL and water partitioning). Observations of vacuum response were consistent with flow in a fractured system. The halon tracers exhibited the greatest amount of retardation, and helium and the perfluoride tracers the least. The alkane tracers were unexpectedly more retarded than the perfluoride tracers, indicating low NAPL saturations and high water saturations. An NAPL saturation of 0.01, water saturation of 0.215, and gas saturation of 0.775 was estimated based on analysis of the suite of tracers comprising helium, perfluoromethylcyclohexane and dibromodifluoromethane, which was considered to be the most robust set. The estimated saturations compare reasonably well to independently determined values.

  17. DRY WELLS IN QUADRANT 25, 26 & 30 – GEOCHEMICAL INVESTIGATIONS INTO RESIDUAL OIL & GAS IN DRY WELLS

    OpenAIRE

    Maqbool, Waqas

    2014-01-01

    This thesis represents the findings concerning core samples from 15 examined exploration wells (with a total of 91 samples) on the eastern flank of the Viking Graben, North Sea, that were classified as dry by NPD (meaning no discovery of oil and gas). These samples were studied using geochemical methodology and analytical methods to evaluate if there might exist the remains of migrated oil or gas. Sample selection at NPD was based on apparent coloration or staining of the sandstone cores. The...

  18. Development and validation of a stability-indicating gas chromatographic method for quality control of residual solvents in blonanserin: a novel atypical antipsychotic agent.

    Science.gov (United States)

    Peng, Ming; Liu, Jin; Lu, Dan; Yang, Yong-Jian

    2012-09-01

    Blonanserin is a novel atypical antipsychotic agent for the treatment of schizophrenia. Ethyl alcohol, isopropyl alcohol and toluene are utilized in the synthesis route of this bulk drug. A new validated gas chromatographic (GC) method for the simultaneous determination of residual solvents in blonanserin is described in this paper. Blonanserin was dissolved in N, N-dimethylformamide to make a sample solution that was directly injected into a DB-624 column. A postrun oven temperature at 240°C for approximately 2 h after the analysis cycle was performed to wash out blonanserin residue in the GC column. Quantitation was performed by external standard analyses and the validation was carried out according to International Conference on Harmonization validation guidelines Q2A and Q2B. The method was shown to be specific (no interference in the blank solution), linear (correlation coefficients ≥0.99998, n = 10), accurate (average recoveries between 94.1 and 101.7%), precise (intra-day and inter-day precision ≤2.6%), sensitive (limit of detection ≤0.2 ng, and limit of quantitation ≤0.7 ng), robust (small variations of carrier gas flow, initial oven temperature, temperature ramping rate, injector and detector temperatures did not significantly affect the system suitability test parameters and peak areas) and stable (reference standard and sample solutions were stable over 48 h). This extensively validated method is ready to be used for the quality control of blonanserin.

  19. CO2 Biofixation by the Cyanobacterium Spirulina sp. LEB 18 and the Green Alga Chlorella fusca LEB 111 Grown Using Gas Effluents and Solid Residues of Thermoelectric Origin.

    Science.gov (United States)

    da Silva Vaz, Bruna; Costa, Jorge Alberto Vieira; de Morais, Michele Greque

    2016-01-01

    The concentration of carbon dioxide (CO2) in the atmosphere has increased from 280 to 400 ppm in the last 10 years, and the coal-fired power plants are responsible for approximately 22 % of these emissions. The burning of fossil fuel also produces a great amount of solid waste that causes serious industrial and environmental problems. The biological processes become interesting alternative in combating pollution and developing new products. The objective of this study was to evaluate the CO2 biofixation potential of microalgae that were grown using gaseous effluents and solid residues of thermoelectric origin. The microalgae Chlorella fusca LEB 111 presented higher rate of CO2 biofixation (42.8 %) (p Spirulina sp. LEB 18. The values for the CO2 biofixation rates and the kinetic parameters of Spirulina and Chlorella cells grown using combustion gas did not differ significantly from those of cells grown using CO2 and a carbon source in the culture media. These microalgae could be grown using ash derived from coal combustion, using the minerals present in this residue as the source of the essential metals required for their growth and the CO2 derived from the combustion gas as their carbon source.

  20. Validation of QuEChERS based method for determination of fenitrothion residues in tomatoes by gas chromatography-flame photometric detector: Decline pattern and risk assessment.

    Science.gov (United States)

    Malhat, Farag; Boulangé, Julien; Abdelraheem, Ehab; Abd Allah, Osama; Abd El-Hamid, Rania; Abd El-Salam, Shokr

    2017-08-15

    A simple and rapid gas chromatography with flame photometric detector (GC-FPD) determination method was developed to detect residue levels and investigate the dissipation pattern and safe use of fenitrothion in tomatoes. A modified quick, easy, cheap, effective, rugged, and safe (QuEChERS) using an ethyl acetate-based extraction, followed by a dispersive solid-phase extraction (d-SPE) with primary-secondary amine (PSA) and graphite carbon black (GCB) for clean up, was applied prior to GC-FPD analysis. The method showed satisfactory linearity, recovery and precision. The limits of detection (LOD) and quantification (LOQ) were 0.005 and 0.01mg/kg, respectively. The residue levels of fenitrothion were best described by first order kinetics with a half-life of 2.2days in tomatoes. The potential health risks posed by fenitrothion were not significant, based on supervised residue trial data. The current findings could provide guidance for safe and reasonable use of fenitrothion in tomatoes and prevent health problems to consumers. Copyright © 2017 Elsevier Ltd. All rights reserved.

  1. Determination of cyflumetofen residue in water, soil, and fruits by modified quick, easy, cheap, effective, rugged, and safe method coupled to gas chromatography/tandem mass spectrometry.

    Science.gov (United States)

    Li, Minmin; Liu, Xingang; Dong, Fengshou; Xu, Jun; Qin, Dongmei; Zheng, Yongquan

    2012-10-01

    A new, highly sensitive, and selective method was developed for the determination of the cyflumetofen residue in water, soil, and fruits by using gas chromatography quadruple mass spectrometry. The target compound was extracted using acetonitrile and then cleaned up using dispersive solid-phase extraction with primary and secondary amine and graphitized carbon black, and optionally by a freezing-out cleanup step. The matrix-matched standards gave satisfactory recoveries and relative standard deviation values in different matrices at three fortified levels (0.05, 0.5, and 1.0 mg kg(-1) ). The overall average recoveries for this method in water, soil, and all fruits matrix at three fortified levels ranged from 76.3 to 101.5% with relative standard deviations in the range of 1.2-11.8% (n = 5). The calculated limits of detection and quantification were typically below 0.005 and 0.015 μg kg(-1), which were much lower than the maximum residue levels established by Japanese Positive List. This study provides a theoretical basis for China to draw up maximum residue level and analytical method for cyflumetofen acaricide in different fruits. © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  2. Development of a multi-residue screening method for the determination of pesticides in cereals and dry animal feed using gas chromatography-triple quadrupole tandem mass spectrometry.

    Science.gov (United States)

    Walorczyk, Stanisław

    2007-09-21

    A multi-residue screening method for simultaneous analysis of 122 gas chromatography amenable pesticides in dry matrices such as cereal grain and certain feedingstuffs was developed. The method entails a simple extraction of re-hydrated sample with acetonitrile followed by a dispersive solid phase extraction (dispersive-SPE) clean-up step prior to the final determination by gas chromatography/triple quadrupole tandem mass spectrometry (GC-MS/MS). Due to complexity of analyzed matrices, two MS/MS transitions were set for each pesticide to eliminate the need for re-analysis of potentially positive samples, and provide unequivocal identification of detected pesticides in accordance with recent guidelines, in a single analytical run. Thus, in the developed GC-MS/MS acquisition method, a total of 216 different multiple reactions monitoring (MRM) transitions were monitored in one set of experimental conditions. To evaluate performance of the method, validation experiments were carried out on wheat grain at three spiking levels (0.01, 0.02 and 0.05 mg kg(-1)). Additional recovery tests at 0.05 mg kg(-1) were carried out on several other matrices. The recoveries ranged between 73 and 129% with associated relative standard deviations between 1 and 29% for the majority of pesticides. Limits of detection were less or equal to 0.01 mg kg(-1) for approximately 68% of pesticides. The applicability of the proposed method to detect and quantify pesticide residues has been demonstrated in the analysis of 136 real samples. Additionally, the method was favorably compared with an acetone extraction method (accepted as a reference method by some of European and U.S. authorities) in the analysis of real samples known to contain pesticide residues.

  3. The Role of Pore-Formers on Grain Interior and Grain Boundary Conductivity in Tape-Cast Porous Sheets for Electrochemical Flue Gas Purification

    DEFF Research Database (Denmark)

    Schmidt, Cristine Grings; Andersen, Kjeld Bøhm; Stamate, Eugen

    2018-01-01

    Ce0.9Gd0.1O1.95 (CGO) electrolytes for electrochemical flue gas purification were fabricated by means of tape casting with different types, shapes and sizes of pore-formers. The sintered bodies were characterized with electrochemical impedance spectroscopy, to investigate the role of the different...... pore-formers on the electrochemical properties of the cast tapes. A strong effect of the different pore-formers on the conductivity (both grain interior and grain boundary conductivities) was observed. In addition, the conductivity data were also correlated with previously obtained gas permeability...

  4. Magnetogasdynamics shock waves in a rotational axisymmetric non-ideal gas with increasing energy and conductive and radiative heat-fluxes

    Science.gov (United States)

    Nath, Gorakh

    2016-07-01

    Self-similar solutions are obtained for one-dimensional adiabatic flow behind a magnetogasdynamics cylindrical shock wave propagating in a rotational axisymmetric non ideal gas with increasing energy and conductive and radiative heat fluxes in presence of an azimuthal magnetic field. The fluid velocities and the azimuthal magnetic field in the ambient medium are assume to be varying and obeying power laws. In order to find the similarity solutions the angular velocity of the ambient medium is taken to be decreasing as the distance from the axis increases. The heat conduction is expressed in terms of Fourier's law and the radiation is considered to be the diffusion type for an optically thick grey gas model. The thermal conductivity and the absorption coefficient are assumed to vary with temperature and density. The effects of the presence of radiation and conduction, the non-idealness of the gas and the magnetic field on the shock propagation and the flow behind the shock are investigated.

  5. High-resolution diffraction for residual stress determination in the NiCrMoV wheel of an axial compressor for a heavy-duty gas turbine

    Science.gov (United States)

    Rogante, M.; Török, G.; Ceschini, G. F.; Tognarelli, L.; Füzesy, I.; Rosta, L.

    2004-07-01

    The wheel of an axial compressor for a heavy-duty gas turbine has been investigated for residual stresses (RS) evaluation of the teeth-section where SANS measurements have previously been performed. Such a component can contain internal RS, either due to the manufacturing process, or to the operating cycles fatigue. The constitutive material is a NiCrMoV steel to ASTM A 471 (type 2) norms (equivalent to B50A420B10); this material is usually adopted in the manufacturing of forged components for gas turbines. Internal radial and hoop RS have been determined, whose values are under the limit of 200kPa. Hoop RS, in general, resulted in higher value than the radial ones. The present experiment represents a particularly important step in the RS determination for gas turbine components, since the measurements reveal that the fatigue of the wheel is also a lifetime limiting factor although, in the same technological field, the available data in the actual neutron techniques literature mainly concern turbine buckets.

  6. High-resolution diffraction for residual stress determination in the NiCrMoV wheel of an axial compressor for a heavy-duty gas turbine

    International Nuclear Information System (INIS)

    Rogante, M.; Toeroek, G.; Ceschini, G.F.; Tognarelli, L.; Fuezesy, I.; Rosta, L.

    2004-01-01

    The wheel of an axial compressor for a heavy-duty gas turbine has been investigated for residual stresses (RS) evaluation of the teeth-section where SANS measurements have previously been performed. Such a component can contain internal RS, either due to the manufacturing process, or to the operating cycles fatigue. The constitutive material is a NiCrMoV steel to ASTM A 471 (type 2) norms (equivalent to B50A420B10); this material is usually adopted in the manufacturing of forged components for gas turbines. Internal radial and hoop RS have been determined, whose values are under the limit of 200 kPa. Hoop RS, in general, resulted in higher value than the radial ones. The present experiment represents a particularly important step in the RS determination for gas turbine components, since the measurements reveal that the fatigue of the wheel is also a lifetime limiting factor although, in the same technological field, the available data in the actual neutron techniques literature mainly concern turbine buckets

  7. Similarity solution for the flow behind a shock wave in a non-ideal gas with heat conduction and radiation heat-flux in magnetogasdynamics

    Science.gov (United States)

    Nath, G.; Vishwakarma, J. P.

    2014-05-01

    The propagation of a spherical (or cylindrical) shock wave in a non-ideal gas with heat conduction and radiation heat-flux, in the presence of a spacially decreasing azimuthal magnetic field, driven out by a moving piston is investigated. The heat conduction is expressed in terms of Fourier's law and the radiation is considered to be of the diffusion type for an optically thick grey gas model. The thermal conductivity K and the absorption coefficient αR are assumed to vary with temperature and density. The gas is assumed to have infinite electrical conductivity and to obey a simplified van der Waals equation of state. The shock wave moves with variable velocity and the total energy of the wave is non-constant. Similarity solutions are obtained for the flow-field behind the shock and the effects of variation of the heat transfer parameters, the parameter of the non-idealness of the gas, both, decreases the compressibility of the gas and hence there is a decrease in the shock strength. Further, it is investigated that with an increase in the parameters of radiative and conductive heat transfer the tendency of formation of maxima in the distributions of heat flux, density and isothermal speed of sound decreases. The pressure and density vanish at the inner surface (piston) and hence a vacuum is form at the center of symmetry. The shock waves in conducting non-ideal gas with conductive and radiative heat fluxes can be important for description of shocks in supernova explosions, in the study of central part of star burst galaxies, nuclear explosion, chemical detonation, rupture of a pressurized vessels, in the analysis of data from exploding wire experiments, and cylindrically symmetric hypersonic flow problems associated with meteors or reentry vehicles, etc. The findings of the present works provided a clear picture of whether and how the non-idealness parameter, conductive and radiative heat transfer parameters and the magnetic field affect the flow behind the shock

  8. Application of Gas Chromatography Coupled to Quadrupole-Orbitrap Mass Spectrometry for Pesticide Residue Analysis in Cereals and Feed Ingredients.

    Science.gov (United States)

    Tienstra, Marc; Mol, Hans G J

    2018-03-01

    A method for residue analysis of pesticides and polychlorinated biphenyls in cereals and feed ingredients based on QuEChERS extraction, programmed temperature vaporizer large-volume injection, and GC with electron ionization (EI) quadrupole Orbitrap full-scan high-resolution MS (60 000 full width at half-maximum at m/z 200) has been developed. In addition to full-scan acquisition, simultaneous full-scan and selected-ion monitoring acquisition was used to improve detectability in incidental cases in which analytes coeluted with intense signals from coextractants. The method was successfully validated down to 10 µg/kg for a single commodity (wheat) using matrix-matched calibration, and for multiple-feed matrixes using standard addition. Identification according to European Union requirements was achieved in >90% of the analyte/matrix combinations, and suggestions for further increasing identification rates have been made. Performance characteristics were compared to an existing method for residue analysis based on GC with EI tandem MS (triple quadrupole).

  9. Determination of pyrethroid pesticide residues in processed fruits and vegetables by gas chromatography with electron capture and mass spectrometric detection.

    Science.gov (United States)

    Sannino, Anna; Bandini, Mirella; Bolzoni, Luciana

    2003-01-01

    A gas chromatographic method was developed for the simultaneous determination of 12 pyrethroids (tefluthrin, bifenthrin, fenpropathrin, cyhalothrin, permethrin, cyfluthrin, cypermethrin, alpha-cypermethrin, flucythrinate, fenvalerate, fluvalinate, and deltamethrin) in tomato puree, peach nectar, orange juice, and canned peas. A miniaturized extraction-partition procedure requiring small amounts of nonchlorinated solvents is used. Samples are extracted with acetone, partitioned with ethyl acetate-cyclohexane (50 + 50, v/v), and cleaned up on a Florisil cartridge. The final extract is analyzed by gas chromatography with both electron capture and mass spectrometric detection modes. Studies at fortification levels of 0.010-0.100 mg/kg gave mean recoveries ranging from 70.2 to 96.0% and coefficients of variation between 4.0 and 13.9% for all compounds. Quantitation limits were < 0.010 mg/kg for electron capture detection.

  10. Detecting Pesticide Residue by Using Modulating Temperature Over a Single SnO2-Based Gas Sensor

    Directory of Open Access Journals (Sweden)

    Zengliang Yu

    2003-09-01

    Full Text Available A new rapid detecting method (called dynamic measurements was reported to detect and distinguish the presence of two pesticide gases in the ambient atmosphere. The method employed only a single SnO2-based gas sensor in a rectangular temperature mode to perform the qualitative analysis of a binary gas mixture (acephate and trichlorphon in air. Polar plots was used for quantitative analysis which the feature extraction was performed by FFT. Experimental results showed that high selectivity of the sensor achieved in the range of 250~3000C and modulating frequency 20mHz, one can easily observe the qualitative difference among the response to pure acephate and trichlorphon gases of the same concentration and to the mixture, and the concentration of pesticide gases can be obtained based on the changes of polar plots.

  11. Multiple fault detection and diagnosis in a gas turbine using nonlinear principal component analysis and structured residuals

    OpenAIRE

    Rincon-Charris, Amilcar; Quevedo Casín, Joseba Jokin

    2013-01-01

    Multiple fault detection and diagnosis is a challenging problem because the number of candidates grows exponentially in the number of faults. In add ition, multiple faults in dynamic systems may be hard to detect, because they can mask or compensate each other’s effects. This paper presents the study of the detection and diagnosis of multiple faults in a SR-30 Gas Turbine using nonlinear principal component analys is as the detection method and structured residua...

  12. Gas

    International Nuclear Information System (INIS)

    1996-01-01

    The French government has decided to modify the conditions of extension of local natural gas authorities to neighbouring districts. The European Union is studying the conditions of internal gas market with the objective of more open markets although considering public service requirements

  13. Towards realizable hyperbolic moment closures for viscous heat-conducting gas flows based on a maximum-entropy distribution

    Science.gov (United States)

    McDonald, James G.; Groth, Clinton P. T.

    2013-09-01

    The ability to predict continuum and transition-regime flows by hyperbolic moment methods offers the promise of several advantages over traditional techniques. These methods offer an extended range of physical validity as compared with the Navier-Stokes equations and can be used for the prediction of many non-equilibrium flows with a lower expense than particle-based methods. Also, the hyperbolic first-order nature of the resulting partial differential equations leads to mathematical and numerical advantages. Moment equations generated through an entropy-maximization principle are particularly attractive due to their apparent robustness; however, their application to practical situations involving viscous, heat-conducting gases has been hampered by several issues. Firstly, the lack of closed-form expressions for closing fluxes leads to numerical expense as many integrals of distribution functions must be computed numerically during the course of a flow computation. Secondly, it has been shown that there exist physically realizable moment states for which the entropy-maximizing problem on which the method is based cannot be solved. Following a review of the theory surrounding maximum-entropy moment closures, this paper shows that both of these problems can be addressed in practice, at least for a simplified one-dimensional gas, and that the resulting flow predictions can be surprisingly good. The numerical results described provide significant motivations for the extension of these ideas to the fully three-dimensional case.

  14. Tuning the conductivity threshold and carrier density of two-dimensional electron gas at oxide interfaces through interface engineering

    Directory of Open Access Journals (Sweden)

    H. J. Harsan Ma

    2015-08-01

    Full Text Available The two-dimensional electron gas (2DEG formed at the perovskite oxides heterostructures is of great interest because of its potential applications in oxides electronics and nanoscale multifunctional devices. A canonical example is the 2DEG at the interface between a polar oxide LaAlO3 (LAO and non-polar SrTiO3 (STO. Here, the LAO polar oxide can be regarded as the modulating or doping layer and is expected to define the electronic properties of 2DEG at the LAO/STO interface. However, to practically implement the 2DEG in electronics and device design, desired properties such as tunable 2D carrier density are necessary. Here, we report the tuning of conductivity threshold, carrier density and electronic properties of 2DEG in LAO/STO heterostructures by insertion of a La0.5Sr0.5TiO3 (LSTO layer of varying thicknesses, and thus modulating the amount of polarization of the oxide over layers. Our experimental result shows an enhancement of carrier density up to a value of about five times higher than that observed at the LAO/STO interface. A complete thickness dependent metal-insulator phase diagram is obtained by varying the thickness of LAO and LSTO providing an estimate for the critical thickness needed for the metallic phase. The observations are discussed in terms of electronic reconstruction induced by polar oxides.

  15. Determination of some selected pesticide residues in apple juice by solid-phase microextraction coupled to gas chromatography – mass spectrometry

    Directory of Open Access Journals (Sweden)

    Andrea Hercegová

    2011-01-01

    Full Text Available The performance of solid phase microextraction (SPME for enrichment of pesticides from apple juice was investigated. Samples were diluted with water, extracted by solid-phase microextraction and analysed by gas chromatography using mass-spectrometry detector (MSD in selected ion monitoring mode (SIM. The method was tested for the following pesticides used mostly in fruit culturing at Slovakia: tebuthylazine, fenitrothion, chlorpyrifos, myclobutanil, cyprodinil, phosalone, pyrimethanil, tebuconazole, kresoxim-methyl, methidathion, penconazole. All pesticides were extracted with polydimethylsiloxane fibre 100 μm thickness. The linear concentration range of application was 0.05 μg dm−3–10 μg dm−3. The method described provides detectabilities complying with the maximum residue levels (MRLs set by regulatory organizations for pesticides in apple juice matrices. The solvent – free SPME procedure was found to be quicker and more cost effective then the solvent extraction methods commonly used.

  16. Determination of pesticide residues and related compounds in water and industrial effluent by solid-phase extraction and gas chromatography coupled to triple quadrupole mass spectrometry.

    Science.gov (United States)

    Martins, Manoel L; Donato, Filipe F; Prestes, Osmar D; Adaime, Martha B; Zanella, Renato

    2013-09-01

    Pollution of drinking water supplies from industrial waste is a result of several industrial processes and disposal practices, and the establishment of analytical methods for monitoring organic compounds related to environmental and health problems is very important. In this work, a method using solid-phase extraction (SPE) and gas chromatography coupled to triple quadrupole tandem mass spectrometry (GC-QqQ-MS/MS) was developed and validated for the simultaneous determination of pesticide residues and related compounds in drinking and surface water as well as in industrial effluent. Optimization of the method was achieved by using a central composite design approach on parameters such as the sample pH and SPE eluent composition. A single SPE consisting of the loading on a polymeric sorbent of 100 mL of sample adjusted to pH 3 and elution with methanol/methylene chloride (10:90, v/v) permitted the obtaining of acceptable recoveries in most cases. The concentration factor associated with sensitivity of the chromatographic analysis permitted the achievement of the method limit of detection values between 0.01 and 0.25 μg L(-1). Recovery assays presented mean recoveries between 70 and 120% for most of the compounds with very good precision, despite the different chemical nature of the compounds analyzed. The selectivity of the method, evaluated through the relative intensity of quantification and qualification ions obtained by GC-QqQ-MS/MS, was considered adequate. The developed method was finally applied to the determination of target analytes in real samples. River water and treated industrial effluent samples presented residues of some compounds, but no detectable residues were found in the drinking water samples evaluated.

  17. [Determination of pesticide residues in fugu, eel and prawn using gas chromatography-mass spectrometry with gel permeation chromatographic clean-up].

    Science.gov (United States)

    Zheng, Feng; Pang, Guofang; Li, Yan; Wang, Minglin; Fan, Chunlin

    2009-09-01

    A multiresidue analytical method was developed for the determination of 191 pesticides in fugu, eel and prawn using gas chromatography-mass spectrometry (GC-MS). The samples were extracted with ethyl acetate and cyclohexane (1:1, v/v), and cleaned-up by gel permeation chromatography (GPC). The GPC eluant collected from 26 min to 44 min was concentrated to 1 mL, then analyzed using GC-MS. A DB-1701 column was used for the separation. The MS detection was performed in selected ion monitoring mode. The recoveries were determined at the two spiked levels of I LOQ and 4 LOQ (LOQ: limit of quantification). The overall recoveries were from 50.2% to 120%, and in which the recoveries of 89.5% pesticides were from 70% to 120%. The relative standard deviations (RSDs) of the recoveries were from 0.6% to 21.6%. The calibration curves of all pesticides showed good linearities in the respective ranges with the correlation coefficient above 0.97. The limits of detection and the limits of quantification were 0.002-0.3 mg/kg and 0.007-1.2 mg/kg, respectively. The sensitivity and accuracy of the method met the requirements of the multiple pesticide residues. This method was applicable to determine 191 multiple pesticide residues in fugu, eel, prawn and other fishes.

  18. Determination of 1,2-dibromoethane, 1,4-dichlorobenzene and naphthalene residues in honey by gas chromatography--mass spectrometry using purge and trap thermal desorption extraction.

    Science.gov (United States)

    Tananaki, Chrisoula; Zotou, Anastasia; Thrasyvoulou, Andreas

    2005-08-12

    A highly sensitive method for the determination of 1,2-dibromoethane, 1,2-dichlorobenzene and naphthalene residues in honey was developed, using gas chromatography-mass spectrometry combined with a purge and trap thermal desorption system as the extraction technique. Optimal conditions for isolation and separation were established and calibration curves were constructed. Linearity was held between 2.4 and 300 microg kg(-1) honey for 1,2-dibromoethane, 0.5 and 300 microg kg(-1) for 1,4-dichlorobenzene and 0.125 and 3000 microg kg(-1) for naphthalene. The detection limits were found to be 0.8, 0.15 and 0.05 microg kg(-1) honey for 1,2-dibromoethane, 1,4-dichlorobenzene and naphthalene, respectively. The method was applied to the analysis of 25 Greek honey samples. 1,2-Dibromoethane was not found in the majority of the samples, while only one sample was found to contain both 1,4-dichlorobenzene and naphthalene residues at concentrations exceeding 10 microg kg(-1).

  19. Determination of Pesticide Residues in Cannabis Smoke

    Directory of Open Access Journals (Sweden)

    Nicholas Sullivan

    2013-01-01

    Full Text Available The present study was conducted in order to quantify to what extent cannabis consumers may be exposed to pesticide and other chemical residues through inhaled mainstream cannabis smoke. Three different smoking devices were evaluated in order to provide a generalized data set representative of pesticide exposures possible for medical cannabis users. Three different pesticides, bifenthrin, diazinon, and permethrin, along with the plant growth regulator paclobutrazol, which are readily available to cultivators in commercial products, were investigated in the experiment. Smoke generated from the smoking devices was condensed in tandem chilled gas traps and analyzed with gas chromatography-mass spectrometry (GC-MS. Recoveries of residues were as high as 69.5% depending on the device used and the component investigated, suggesting that the potential of pesticide and chemical residue exposures to cannabis users is substantial and may pose a significant toxicological threat in the absence of adequate regulatory frameworks.

  20. Residual deposits (residual soil)

    International Nuclear Information System (INIS)

    Khasanov, A.Kh.

    1988-01-01

    Residual soil deposits is accumulation of new formate ore minerals on the earth surface, arise as a result of chemical decomposition of rocks. As is well known, at the hyper genes zone under the influence of different factors (water, carbonic acid, organic acids, oxygen, microorganism activity) passes chemical weathering of rocks. Residual soil deposits forming depends from complex of geologic and climatic factors and also from composition and physical and chemical properties of initial rocks

  1. Environmental performance, mechanical and microstructure analysis of concrete containing oil-based drilling cuttings pyrolysis residues of shale gas.

    Science.gov (United States)

    Wang, Chao-Qiang; Lin, Xiao-Yan; He, Ming; Wang, Dan; Zhang, Si-Lan

    2017-09-15

    The overall objective of this research project is to investigate the feasibility of incorporating oil-based drilling cuttings pyrolysis residues (ODPR) and fly ash serve as replacements for fine aggregates and cementitious materials in concrete. Mechanical and physical properties, detailed environmental performances, and microstructure analysis were carried out. Meanwhile, the early hydration process and hydrated products of ODPR concrete were analyzed with X-ray diffraction (XRD), Fourier transform infrared (FT-IR), scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDX). The results indicated that ODPR could not be categorize into hazardous wastes. ODPR had specific pozzolanic characteristic and the use of ODPR had certain influence on slump and compressive strength of concrete. The best workability and optimal compressive strength were achieved with the help of 35% ODPR. Environmental performance tests came to conclusion that ODPR as recycled aggregates and admixture for the preparation of concrete, from the technique perspective, were the substance of mere environmental contamination. Copyright © 2017 Elsevier B.V. All rights reserved.

  2. Design of a compressed air modulator to be used in comprehensive multidimensional gas chromatography and its application in the determination of pesticide residues in grapes.

    Science.gov (United States)

    Pizzutti, Ionara R; Vreuls, René J J; de Kok, André; Roehrs, Rafael; Martel, Samile; Friggi, Caroline A; Zanella, Renato

    2009-04-10

    In this study, a new modulator that is simple, robust and presents low operation costs, was developed. This modulator uses compressed air to cool two small portions in the first centimeters of the second chromatographic column of a comprehensive multidimensional gas chromatography (GCxGC) system. The results show a variation in the peak area less than 3 and 5% to alkanes and pesticides, respectively. The standard deviations for the retention times in the first and second dimension are around 0.05 min and 0.05s for all the compounds. The system was optimized with n-alkanes. The GCxGC system proposed was applied in the determination of pyrethroid pesticides (bifenthrin, cypermethrin, deltamethrin, fenvalerate, esfenvalerate, cis- and trans-permethrin) in grape samples. Samples were extracted by the mini-Luke modified method and pesticides were quantified by comprehensive multidimensional gas chromatography with micro electron-capture detection (microECD). The values of method limit of quantification (LOQ) were 0.01-0.02 mg kg(-1) for all studied pyrethroid and the values of recovery were between 94.3 and 115.2%, with good precision (RSDcompressed air has the potential for application in the analysis of a wider range of pesticide residues in other commodities since it provides low values of LOQ with acceptable accuracy and precision.

  3. Proposed systematic methodology for analysis of Pb-210 radioactivity in residues produced in Brazilian natural gas pipes

    International Nuclear Information System (INIS)

    Ferreira, Aloisio Cordilha

    2003-11-01

    Since the 80's, the potential radiological hazards due to the handling of solid wastes contaminated with Rn-222 long-lived progeny - Pb-210 in special - produced in gas pipes and removed by pig operations have been subject of growing concern abroad our country. Nevertheless, little or no attention has been paid to this matter in the Brazilian plants up to now, being these hazards frequently underestimated or even ignored. The main purpose of this work was to propose a systematic methodology for analysis of Pb-210 radioactivity in black powder samples from some Brazilian plants, through the evaluation of direct Pb-210 gamma spectrometry and Bi-210 beta counting technical viabilities. In both cases, one in five samples of black powder analysed showed relevant activity (above 1Bq/kg) of Pb-210, being these results probably related to particular features of each specific plant (production levels, reservoir geochemical profile, etc.), in such a way that a single pattern is not observed. For the proposed methodology, gamma spectrometry proved to be the most reliable technique, showing a 3.5% standard deviation, and, for a 95% confidence level, overall fitness in the range of Pb-210 concentration of activity presented in the standard sample reference sheet, provided by IAEA for intercomparison purposes. In the Brazilian scene, however, the availability of statistically supported evidences is insufficient to allow the potential radiological hazard due to the management of black powder to be discarded. Thus, further research efforts are recommended in order to detect the eventually critical regions or plants where gas exploration, production and processing practices will require a regular program of radiological surveillance, in the near future. (author)

  4. Drude weight and optical conductivity of a two-dimensional heavy-hole gas with k-cubic spin-orbit interactions

    Energy Technology Data Exchange (ETDEWEB)

    Mawrie, Alestin; Ghosh, Tarun Kanti [Department of Physics, Indian Institute of Technology-Kanpur, Kanpur 208 016 (India)

    2016-01-28

    We present a detailed theoretical study on zero-frequency Drude weight and optical conductivity of a two-dimensional heavy-hole gas (2DHG) with k-cubic Rashba and Dresselhaus spin-orbit interactions. The presence of k-cubic spin-orbit couplings strongly modifies the Drude weight in comparison to the electron gas with k-linear spin-orbit couplings. For large hole density and strong k-cubic spin-orbit couplings, the density dependence of Drude weight deviates from the linear behavior. We establish a relation between optical conductivity and the Berry connection. Unlike two-dimensional electron gas with k-linear spin-orbit couplings, we explicitly show that the optical conductivity does not vanish even for equal strength of the two spin-orbit couplings. We attribute this fact to the non-zero Berry phase for equal strength of k-cubic spin-orbit couplings. The least photon energy needed to set in the optical transition in hole gas is one order of magnitude smaller than that of electron gas. Types of two van Hove singularities appear in the optical spectrum are also discussed.

  5. Novel and rapid method for determination of organophosphorus pesticide residues in edible fungus using direct gas purge microsyringe extraction coupled on-line with gas chromatography-mass spectrometry.

    Science.gov (United States)

    Nan, Jingxi; Wang, Juan; Piao, Xiangfan; Yang, Cui; Wu, Xue; Quinto, Maurizio; Li, Donghao

    2015-09-01

    In this work a new analytical method for a rapid and simultaneous determination of 28 organophosphorus pesticides (OPPs) residues in edible fungus using gas purge microsyringe extraction (GP-MSE), coupled with on-line gas chromatography-mass spectrometry (GP-MSE-GC-MS) has been developed and optimized. GP-MSE, a novel gas flow liquid-phase microextraction technique, has been then fruitfully used as innovative and one-step extraction procedure, allowing a direct injection into the gas chromatograph coupled with a mass spectrometry detector (GC-MS) system without any further cleaning step. Once optimized, the GP-MSE-GC-MS analysis procedure showed reproducibility values, resolutions, linear responses, detection and quantification limits that allowed to consider this method suitable for the analysis of the 28 OPPs in real samples. Furthermore, OPP recoveries and the relative standard deviations (RSDs) ranged from 85.26% to 100.21%, and from 1.6% to 6.9%, respectively. This procedure was then used for the analysis of real samples and the obtained results were compared with those of ultrasonic extraction-solid phase extraction. Among the 28 OPPs, 14 of them were found in Lentinus edodes and Enoki mushrooms fungus samples, with a total concentrations of 112.7 and 210.7 μg kg(-1), respectively. This work demonstrated then that GP-MSE-GC-MS provided a highly efficient, solvent-saving, accurate and sensitive quantitative analysis method for a rapid determination of OPPs in edible fungus. Copyright © 2015 Elsevier B.V. All rights reserved.

  6. Collimator system for the stabilization of the dynamical residual-gas pressure in the heavy-ion synchrotron SIS18; Kollimatorsystem zur Stabilisierung des dynamischen Restgasdruckes im Schwerionensynchrotron SIS18

    Energy Technology Data Exchange (ETDEWEB)

    Omet, Carsten

    2009-01-15

    In order to achieve higher beam intensities of heavy ion beams in ring accelerators, low charge state ions can be used. By lowering the charge state, the space charge limit is shifted to higher particle numbers and stripping losses can be avoided. During test operation of the SIS18 at GSI with high intensity low charge state heavy ion beams, strong intensity dependent beam losses have been observed. It was found that these beam losses are originated to a large extent by the change of charge state of the circulating ions during collisions with residual gas atoms. The resulting deviation of m/q relative to the reference ion leads, in combination with dispersive elements in the ion optic lattice, to a modified trajectory, followed by the loss of the ion on the beam pipe. At the impact position, loosely bound residual gas molecules are released by ion stimulated desorption which increases the residual gas pressure locally. This pressure rise itself enhances the charge exchange rate, which can develop into a self amplifying process of pressure rise and subsequent beam loss. A method for the stabilization of the dynamic residual gas pressure is the use of special catcher systems, which minimize the production of desorption gases and remove them by strong pumping. Therefore, the pressure on the beam axis should remain as stable as possible. Other processes, e.g. Coulomb scattering of the beam ions by residual gas particles and unavoidable systematic beam losses can increase the gas pressure additionally. The pressure in the accelerator is further subjected to ionization of the residual gas atoms themselves, thermal out gassing of the beam pipes, insertions and pumps. In this work, a detailed numerical model of the interplay between the residual gas pressure dynamics in the accelerator, possible stabilization measures, e.g. by catchers and the resulting beam life time has been developed. The forecasted beam life times and pressures are verified by machine experiments, as

  7. On possibility of using E, H - crossed fields and gas-dynamic flowing of argon in the processes of degassing by the method of ion-stimulated desorption of residual gas in the KUTI-20

    International Nuclear Information System (INIS)

    Sharapov, V.E.

    1985-01-01

    In the project considered if the possibility to use the degassing of an adhezatior chamber inner walls, using the method of ion-stimulated desorption (ISD) of residual gas in the glow discharge is considered. It is suggested that the experiment should be realized using the model or the KUTI (PKUTI) prototype to decrease operation pressure to p -7 Pa (2x10 -9 Tor) at the expense of introduction of the technology described and certain modifications in the processes of leak-in and pumping. The use of crossed E,H-fields and gasodynamic regime of argon flow in the process of preliminary degassing of the adhezator chamber by the glow discharge is the main idea of the project

  8. Fast gas chromatographic residue analysis in animal feed using split injection and atmospheric pressure chemical ionisation tandem mass spectrometry.

    Science.gov (United States)

    Tienstra, M; Portolés, T; Hernández, F; Mol, J G J

    2015-11-27

    Significant speed improvement for instrumental runtime would make GC–MS much more attractive for determination of pesticides and contaminants and as complementary technique to LC–MS. This was the trigger to develop a fast method (time between injections less than 10 min) for the determination of pesticides and PCBs that are not (or less) amenable to LC–MS. A key factor in achieving shorter analysis time was the use of split injection (1:10) which allowed the use of a much higher initial GC oven temperature. A shorter column (15 m), higher temperature ramp, and higher carrier gas flow rate (6 mL/min) further contributed to analysis-time reduction. Chromatographic resolution was slightly compromised but still well fit-for-purpose. Due to the high sensitivity of the technique used (GC–APCI-triple quadrupole MS/MS), quantification and identification were still possible down to the 10 μg/kg level, which was demonstrated by successful validation of the method for complex feed matrices according to EU guidelines. Other advantages of the method included a better compatibility of acetonitrile extracts (e.g. QuEChERS) with GC, and a reduced transfer of co-extractants into the GC column and mass spectrometer.

  9. Theoretical reconsiderations when estimating the mesophyll conductance to CO2 diffusion in leaves of C3 plants by analysis of combined gas exchange and chlorophyll fluorescence measurements

    NARCIS (Netherlands)

    Yin, X.; Struik, P.C.

    2009-01-01

    Existing methods to estimate the mesophyll conductance to CO2 diffusion (gm) are often based on combined gas exchange and chlorophyll fluorescence measurements. However, estimations of average gm by these methods are often unreliable either because the range of usable data is too narrow or because

  10. Application of acetone acetals as water scavengers and derivatization agents prior to the gas chromatographic analysis of polar residual solvents in aqueous samples.

    Science.gov (United States)

    van Boxtel, Niels; Wolfs, Kris; Van Schepdael, Ann; Adams, Erwin

    2015-12-18

    The sensitivity of gas chromatography (GC) combined with the full evaporation technique (FET) for the analysis of aqueous samples is limited due to the maximum tolerable sample volume in a headspace vial. Using an acetone acetal as water scavenger prior to FET-GC analysis proved to be a useful and versatile tool for the analysis of high boiling analytes in aqueous samples. 2,2-Dimethoxypropane (DMP) was used in this case resulting in methanol and acetone as reaction products with water. These solvents are relatively volatile and were easily removed by evaporation enabling sample enrichment leading to 10-fold improvement in sensitivity compared to the standard 10μL FET sample volumes for a selection of typical high boiling polar residual solvents in water. This could be improved even further if more sample is used. The method was applied for the determination of residual NMP in an aqueous solution of a cefotaxime analogue and proved to be considerably better than conventional static headspace (sHS) and the standard FET approach. The methodology was also applied to determine trace amounts of ethylene glycol (EG) in aqueous samples like contact lens fluids, where scavenging of the water would avoid laborious extraction prior to derivatization. During this experiment it was revealed that DMP reacts quantitatively with EG to form 2,2-dimethyl-1,3-dioxolane (2,2-DD) under the proposed reaction conditions. The relatively high volatility (bp 93°C) of 2,2-DD makes it possible to perform analysis of EG using the sHS methodology making additional derivatization reactions superfluous. Copyright © 2015 Elsevier B.V. All rights reserved.

  11. Determination of residual acetone and acetone related impurities in drug product intermediates prepared as Spray Dried Dispersions (SDD) using gas chromatography with headspace autosampling (GCHS).

    Science.gov (United States)

    Quirk, Emma; Doggett, Adrian; Bretnall, Alison

    2014-08-05

    Spray Dried Dispersions (SDD) are uniform mixtures of a specific ratio of amorphous active pharmaceutical ingredient (API) and polymer prepared via a spray drying process. Volatile solvents are employed during spray drying to facilitate the formation of the SDD material. Following manufacture, analytical methodology is required to determine residual levels of the spray drying solvent and its associated impurities. Due to the high level of polymer in the SDD samples, direct liquid injection with Gas Chromatography (GC) is not a viable option for analysis. This work describes the development and validation of an analytical approach to determine residual levels of acetone and acetone related impurities, mesityl oxide (MO) and diacetone alcohol (DAA), in drug product intermediates prepared as SDDs using GC with headspace (HS) autosampling. The method development for these analytes presented a number of analytical challenges which had to be overcome before the levels of the volatiles of interest could be accurately quantified. GCHS could be used after two critical factors were implemented; (1) calculation and application of conversion factors to 'correct' for the reactions occurring between acetone, MO and DAA during generation of the headspace volume for analysis, and the addition of an equivalent amount of polymer into all reference solutions used for quantitation to ensure comparability between the headspace volumes generated for both samples and external standards. This work describes the method development and optimisation of the standard preparation, the headspace autosampler operating parameters and the chromatographic conditions, together with a summary of the validation of the methodology. The approach has been demonstrated to be robust and suitable to accurately determine levels of acetone, MO and DAA in SDD materials over the linear concentration range 0.008-0.4μL/mL, with minimum quantitation limits of 20ppm for acetone and MO, and 80ppm for DAA. Copyright

  12. An accurate, residue-level, pair potential of mean force for folding and binding based on the distance-scaled, ideal-gas reference state.

    Science.gov (United States)

    Zhang, Chi; Liu, Song; Zhou, Hongyi; Zhou, Yaoqi

    2004-02-01

    Structure prediction on a genomic scale requires a simplified energy function that can efficiently sample the conformational space of polypeptide chains. A good energy function at minimum should discriminate native structures against decoys. Here, we show that a recently developed, residue-specific, all-atom knowledge-based potential (167 atomic types) based on distance-scaled, finite ideal-gas reference state (DFIRE-all-atom) can be substantially simplified to 20 residue types located at side-chain center of mass (DFIRE-SCM) without a significant change in its capability of structure discrimination. Using 96 standard multiple decoy sets, we show that there is only a small reduction (from 80% to 78%) in success rate of ranking native structures as the top 1. The success rate is higher than two previously developed, all-atom distance-dependent statistical pair potentials. Applied to structure selections of 21 docking decoys without modification, the DFIRE-SCM potential is 29% more successful in recognizing native complex structures than an all-atom statistical potential trained by a database of dimeric interfaces. The potential also achieves 92% accuracy in distinguishing true dimeric interfaces from artificial crystal interfaces. In addition, the DFIRE potential with the C(alpha) positions as the interaction centers recognizes 123 native structures out of a comprehensive 125-protein TOUCHSTONE decoy set in which each protein has 24,000 decoys with only C(alpha) positions. Furthermore, the performance by DFIRE-SCM on newly established 25 monomeric and 31 docking Rosetta-decoy sets is comparable to (or better than in the case of monomeric decoy sets) that of a recently developed, all-atom Rosetta energy function enhanced with an orientation-dependent hydrogen bonding potential.

  13. Multi-residue method for the determination of organochlorine pesticides in fish feed based on a cleanup approach followed by gas chromatography-triple quadrupole tandem mass spectrometry.

    Science.gov (United States)

    Nardelli, Valeria; dell'Oro, Daniela; Palermo, Carmen; Centonze, Diego

    2010-07-23

    A multi-residue method for the determination of organochlorine pesticides in fish feed samples was developed and optimized. The method is based on a cleanup step of the extracted fat, carried out by liquid-liquid extraction on diatomaceous earth cartridge with n-hexane/acetonitrile (80/20, v/v) followed by solid phase extraction (SPE) with silica gel-SCX cartridge, before the identification and quantification of the residues by gas chromatography-triple quadrupole tandem spectrometry (GC-MS/MS). Performance characteristics, such as accuracy, precision, linear range, limits of detection (LOD) and quantification (LOQ), for each pesticide were determined. Instrumental LODs ranged from 0.01 to 0.11 microg L(-1), LOQs were in the range of 0.02-0.35 microg L(-1), and calibration curves were linear (r2>0.999) in the whole range of explored concentrations (5-100 microg L(-1)). Repeatability values were in the range of 3-15%, evaluated from the relative standard deviation of six samples spiked at 100 microg kg(-1) of fat, and in compliance with that derived by the Horwitz's equation. No matrix effects or interfering substances were observed in fish feed analyses. The proposed method allowed high recoveries (92-116%) of spiked extracted fat samples at 100 microg kg(-1), and very low LODs (between 0.02 and 0.63 microg kg(-1)) and LOQs (between 0.05 and 2.09 microg kg(-1)) determined in fish feed samples. Copyright (c) 2010 Elsevier B.V. All rights reserved.

  14. [Monitoring of the residue of fosthiazate in water samples using solid-phase extraction coupled with gas chromatography/mass spectrometry].

    Science.gov (United States)

    Zhu, Jing; Zhou, Xin; Fu, Chunmei; Liu, Sankang; Li, Zhangwan

    2004-11-01

    Solid-phase extraction (SPE) coupled with gas chromatography/mass spectrometry (GC/MS) was used to determine the fosthiazate residue in water samples. The water samples were first filtered through cellulose filters (0.45 microm pore size). A 100 mL volume of filtered water, in which 1 mL of methanol has been added, was then passed through a pre-conditioned 3 cm C18 cartridge at a flow-rate of 1.5 mL/min. Elution was performed by 1 mL of methanol. The eluant was finally dried under reduced pressure for solvent evaporation. The volume was quantitatively adjusted to 0.5 mL with methanol. The analysis was carried out on GC/MS. The mass spectrometer was operated in selected ion monitoring (SIM) mode. According to mass spectrum of fosthiazate, three selected ions at m/z of 126, 195, 283, respectively, were monitored for identification and quantification. High sensitivity and selectivity were achieved by using this method. The limit of detection for fosthiazate in water samples was determined to be 56.4 ng/L. The linearity was demonstrated over a wide range of concentrations covering from 0.282 to 141 microg/L. The recoveries were more than 85.5% and the relative standard deviations for the overall procedure were less than 4.42%. The fosthiazate residue was detected in the water samples from a pool near cropland where fosthiazate was used. The results demonstrate the suitability of the SPE-GC/MS approach for the analysis of fosthiazate in water.

  15. Conversion of direct process high-boiling residue to monosilanes

    Science.gov (United States)

    Brinson, Jonathan Ashley; Crum, Bruce Robert; Jarvis, Jr., Robert Frank

    2000-01-01

    A process for the production of monosilanes from the high-boiling residue resulting from the reaction of hydrogen chloride with silicon metalloid in a process typically referred to as the "direct process." The process comprises contacting a high-boiling residue resulting from the reaction of hydrogen chloride and silicon metalloid, with hydrogen gas in the presence of a catalytic amount of aluminum trichloride effective in promoting conversion of the high-boiling residue to monosilanes. The present process results in conversion of the high-boiling residue to monosilanes. At least a portion of the aluminum trichloride catalyst required for conduct of the process may be formed in situ during conduct of the direct process and isolation of the high-boiling residue.

  16. Deep eutectic solvent based gas-assisted dispersive liquid-phase microextraction combined with gas chromatography and flame ionization detection for the determination of some pesticide residues in fruit and vegetable samples.

    Science.gov (United States)

    Farajzadeh, Mir Ali; Sattari Dabbagh, Masoumeh; Yadeghari, Adeleh

    2017-05-01

    In this study, a gas-assisted dispersive liquid-phase microextraction method using a deep eutectic solvent as the extraction solvent combined with gas chromatography and flame ionization detection was developed for the extraction and determination of some pesticide residues in vegetable and fruit juice samples. In this method, choline chloride and 4-chlorophenol at a molar ratio of 1:2 were mixed. By heating and vortexing, a clear, water-immiscible, and homogeneous liquid was formed. The obtained deep eutectic solvent was added to an aqueous solution of the analytes in a conical test tube. Air was bubbled into the aqueous solution and a cloudy solution was obtained. During this step, the analytes were extracted into the fine droplets of the extraction solvent. After centrifugation, an aliquot of the settled phase was injected into the separation system. Under the optimum extraction conditions, enrichment factors, and extraction recoveries were obtained in the ranges of 247-355 and 49-71%, respectively. The obtained values for the limits of detection and quantification were in the ranges of 0.24-1.4 and 0.71-4.2 μg/L, respectively. The proposed method is simple, fast, efficient, and inexpensive. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  17. The electrical conductivity of the flame front, as a characteristic of the rate of heat release and composition of gas fuel in SI engines

    Science.gov (United States)

    Smolenskaya, N. M.

    2018-01-01

    The paper considers the possibility of using the electrical conductivity of the flame front as a characteristic of the rate of heat release and composition of gas fuel in a SI engines. Based on the analysis of the experimental data, the dependences of the parameters of the electrical conductivity of the flame front on the rate of heat release are obtained with the variation of the chemical activity of the gas fuel in a SI engines. The influence of the composition of the mixture and the effect of the amount of added hydrogen on the increase in the rate of heat release and, consequently, on the increase in the electrical conductivity of the flame. The obtained dependences will allow to increase the efficiency and reduce the toxicity of the SI engines operation during the regulation of the working process by ionization sensors.

  18. Penetration of gas discharge through the gas–liquid interface into the bulk volume of conductive aqueous solution

    Czech Academy of Sciences Publication Activity Database

    Hoffer, Petr; Koláček, Karel; Stelmashuk, Vitaliy; Lukeš, Petr

    2015-01-01

    Roč. 43, č. 11 (2015), s. 3868-3875 ISSN 0093-3813 R&D Projects: GA ČR(CZ) GA15-12987S Institutional support: RVO:61389021 Keywords : atmospheric-pressure plasmas * electric discharges * liquids * water Subject RIV: BL - Plasma and Gas Discharge Physics Impact factor: 0.958, year: 2015

  19. Gas chromatographic determination of electron capture sensitive volatile industrial chemical residues in foods, using AOAC pesticide multiresidue extraction and cleanup procedures.

    Science.gov (United States)

    Yurawecz, M P; Puma, B J

    1986-01-01

    Electron capture (EC) gas chromatographic (GC) parameters have been developed for determining some of the more volatile industrial chemicals that can be determined by the AOAC multiresidue method for organochlorine and organophosphorus pesticides with modified GC operating conditions. Retention times relative to pentachlorobenzene are reported for 143 industrial chemicals, pesticides, and related compounds on OV-101 GC columns at 130 degrees C. Also reported for most of the compounds are recoveries from fortified samples carried through the AOAC extraction and cleanup procedures for fatty and/or nonfatty foods, Florisil elution characteristics, and GC relative retention times on mixed OV-101 + OV-210 columns at 130 degrees C. Our laboratory has used the modified EC/GC parameters with the AOAC multiresidue extraction/cleanup procedures to determine many volatile halogenated industrial chemical contaminants in foods, chiefly in samples of fresh-water fish. Other modifications of the AOAC method are described to improve the tentative identification and quantitative measurement of these volatile residues.

  20. Determination of the limits of identification and quantitation of selected organochlorine and organophosphorous pesticide residues in surface water by full-scan gas chromatography/mass spectrometry.

    Science.gov (United States)

    Tahboub, Yahya R; Zaater, Mohammad F; Al-Talla, Zeiad A

    2005-12-09

    In this work, we report a reliable method for quantitation and determination of the limits of identification of 14 organochlorine and organophosphorous pesticide (OPP) residues in surface water. The method features the simultaneous identification and quantitation of targeted pesticides and the possibility of identification of any other eluting compounds. The method is based on liquid-liquid extraction (LLE) with a mixture of petroleum ether and dichloromethane (70:30, v/v) followed by gas chromatographic separation and a full-scan mass spectrometric detection (GC-MS). The method presents a new validation parameter, limit of identification (LOI) which is defined for our purpose as the lowest analyte concentration that yields a library searchable mass spectrum. The method is linear over the range 0.048-1.20microgL(-1) for nine pesticides and 0.024-0.60microgL(-1) for the other five pesticides. Correlation coefficients vary between 0.988 and 0.998. Limits of detection (LODs) vary between 0.005 and 0.05microgL(-1) for 4,4'-DDT and LOIs vary between 0.012 and 0.048microgL(-1).

  1. Optimization of a multi-residue method for 101 pesticides in green tea leaves using gas chromatography–tandem mass spectrometry

    Directory of Open Access Journals (Sweden)

    Xue Hou

    Full Text Available ABSTRACT A method for analysis of 101 pesticide residues in tea leaves was developed and validated for the first time. Pure acetonitrile was used as extraction solvent rather than acetonitrile after matrix hydration based on the amount of co-extracts and recoveries performance. During clean-up procedure, primary-secondary amine/graphitized carbon black (500 mg was selected, which exhibited outstanding properties in clean-up capabilities and recoveries of pesticides comparing to primary-secondary amine/graphitized carbon black (250 mg, NH2-Carbon and TPT absorbents. The method was validated employing gas chromatography coupled to tandem mass spectrometry at the spiked concentration levels of 0.050 and 0.100 mg kg−1. For most of the targeted pesticides, the percent recoveries range from 70 to 120%, with relative standard deviations <20%. The linear correlation coefficients (r 2 were higher than 0.99 at concentration levels of 0.025–0.250 mg kg−1. Limits of quantification ranged from 1.1 to 25.3 µg kg−1 for all pesticides. The developed method was successfully applied to the determination of pesticides in tea leaf samples.

  2. Determination of residual volatile organic compounds migrated from polystyrene food packaging into food simulant by headspace solid phase micro extraction-gas chromatography

    International Nuclear Information System (INIS)

    Mohd Marsin Sanagi; Ling, Susie Lu; Zalilah Nasir; Wan Aini Wan Ibrahim; Abu Naim, Ahmedy

    2008-01-01

    The residual styrene and other volatile organic compounds (VOCs) present in the polystyrene food packaging are of concern as these compounds have the potential to migrate into the food in contact. This work describes a method for quantitative determination of VOCs, namely styrene, toluene, ethyl benzene, iso-propylbenzene and n-propylbenzene that have migrated from polystyrene food packaging into food stimulant by gas chromatography-flame ionization detection (GC-FID). Headspace solid phase micro extraction (HS-SPME) technique was applied for migration test using water as food stimulant. The effects of extraction variables including sample volume, eluotropic strength, extraction temperature, extraction time, desorption time, sample agitation, and salt addition on the amounts of the extracted analyses were studied to obtain the optimal HS-SPME conditions. The optimized method was applied to test the VOCs migrated from polystyrene bowls and cups at storage temperatures ranging from 24 to 80 degree Celsius for 30 min. Styrene and ethyl benzene were found to migrate from the samples into the food stimulant. The migration of analyze was found to be strongly dependent upon the storage temperature. The HS-SPME is useful as an alternative method to determine the migration of VOCs from food packaging material into food stimulant. (author)

  3. A multi-residue method for determination of 70 organic micropollutants in surface waters by solid-phase extraction followed by gas chromatography coupled to tandem mass spectrometry.

    Science.gov (United States)

    Terzopoulou, Evangelia; Voutsa, Dimitra; Kaklamanos, George

    2015-01-01

    A multi-residue method, based on gas chromatography coupled to tandem mass spectrometry (GC-MS/MS), has been developed for the determination of 70 organic micropollutants from various chemical classes (organochlorinated, organophosphorous, triazines, carbamate and urea, polycyclic aromatic hydrocarbons, polychlorinated biphenyls, pharmaceuticals, phenols, etc.) in surface waters. A single-step SPE extraction using OASIS HLB cartridges was employed for the recovery of target micropollutants. The method has been validated according to monitoring performance criteria of the Water Framework Directive, taking into account the approved guidelines on quality assurance and quality control. The recoveries ranged from 60 to 110 %, the coefficient of variation from 0.84 to 27.4 %, and the uncertainty from 6 to 37 %. The LOD varied from 6.0 to 40 ng/L. The limits of quantification for the priority pollutants anthracene, alachlor, atrazine, benzo(a)pyrene, chlorfenvinphos, diuron, isoproturon, nonylphenol, simazine, and terbutryn fulfill the criterion of diuron, isoproturon, salicylic acid, chlorfenvinphos, 1,2-benzanthracene, pyrene, diflubenzuron, and carbaryl exhibited the highest detection frequencies.

  4. Propagation of a spherical shock wave in mixture of non-ideal gas and small solid particles under gravitational field with conductive and radiative heat fluxes

    Science.gov (United States)

    Nath, Gorakh

    Self-similar solutions are obtained for one-dimensional unsteady adiabatic flow behind a spherical shock wave propagating in a dusty gas with conductive and radiative heat fluxes under a gravitational field. The shock is assumed to be driven out by a moving piston and the dusty gas to be a mixture of non-ideal (or perfect) gas and small solid particles, in which solid particles are continuously distributed. It is assumed that the equilibrium flow-conditions are maintained and variable energy input is continuously supplied by the piston. The heat conduction is express in terms of Fourier’s law and the radiation is considered to be of the diffusion type for an optically thick grey gas model. The thermal conductivity and the absorption coefficient are assumed to vary with temperature and density. The medium is assumed to be under a gravitational field due to heavy nucleus at the origin (Roche Model). The unsteady model of Roche consists of a dusty gas distributed with spherical symmetry around a nucleus having large mass It is assumed that the gravitational effect of the mixture itself can be neglected compared with the attraction of the heavy nucleus. The density of the ambient medium is taken to be constant. Our analysis reveals that after inclusion of gravitational field effect surprisingly the shock strength increases and remarkable difference can be found in the distribution of flow variables. The effects of the variation of the heat transfer parameters, the gravitational parameter and non-idealness of the gas in the mixture are investigated. Also, the effects of an increase in (i) the mass concentration of solid particles in the mixture and (ii) the ratio of the density of solid particles to the initial density of the gas on the flow variables are investigated. It is found that the shock strength is increased with an increase in the value of gravitational parameter. Further, it is investigated that the presence of gravitational field increases the

  5. Analisis Pemodelan Sistem Hibrid Proton Conducting Solid Oxide Fuel Cell (pSOFC – Turbin Gas Mikro Pada Matlab-Simulink

    Directory of Open Access Journals (Sweden)

    Bayu Pranoto

    2016-05-01

    Full Text Available This study simulated Proton Conducting Solid Oxide Fuel Cell (pSOFC – Micro Gas Turbine (MGT hybrid system on three different configuration. The first configuration use bypass hot gas from combustor going to fuel heater without  pass the turbine first. The second configuration use bypass hot gas out of turbine going to fuel heater. The third configuration is combined bypass out of combustor and also bypass out of turbine. The performance of these system are analyzed by using variation of operating pressure, fuel utilization (Uf, steam to carbon ratio (S/C, and bypass valve. Moreover, the impact of different bypass position were also evaluated. The result shows that the efficiency of using a double bypass hot gas flow after combustor and turbine is about 67%. This configuration became the best one among of another two configuration which proposed in this research.  The utilization of heat by using a double bypass hot flow gas after turbine and combustor has proven more effective to increase the system efficiency. Means that it can reduce the heat losses of the system.

  6. Determination of hydrogen in zirconium and its alloys by melt extraction under carrier gas flow using thermal conductivity cell as detector

    International Nuclear Information System (INIS)

    Akhtar, J.; Ahmed, M.; Mohammad, B.; Jan, S.; Waqar, F.

    1987-06-01

    In the production of zirconium metal and its alloys the presence of hydrogen impurity affects mechanical and corrosion resistance properties of the product. Therefore, determination of hydrogen contents of the product is necessary. Conditions for its analysis by melt extraction under carrier gas stream using thermal conductivity cell as detector were studied and optimised. The method is capable of measuring hydrogen impurity in parts per million range. (author)

  7. Potential use of only Yb2O3 in producing dense Si3N4 ceramics with high thermal conductivity by gas pressure sintering

    OpenAIRE

    Zhu, Xinwen; Zhou, You; Hirao, Kiyoshi; Ishigaki, Takamasa; Sakka, Yoshio

    2010-01-01

    Yb2O3 is an efficient sintering additive for enhancing not only thermal conductivity but also the high-temperature mechanical properties of Si3N4 ceramics. Here we report the fabrication of dense Si3N4 ceramics with high thermal conductivity by the gas pressure sintering of α-Si3N4 powder compacts, using only Yb2O3 as an additive, at 1900 °C under a nitrogen pressure of 1 MPa. The effects of Yb2O3 content, sample packing condition and sintering time on the densification, microstructure and th...

  8. Constant-pressure well test analysis of finite-conductivity hydraulically fractured gas wells influenced by non-Darcy flow effects

    Energy Technology Data Exchange (ETDEWEB)

    Nashawi, Ibrahim Sami [Department of Petroleum Engineering, College of Engineering and Petroleum, Kuwait University, P.O. Box 5969, Safat 13060 (Kuwait)

    2006-09-15

    Non-Darcy flow effects have long been recognized to have serious adverse impact on the performance of high flow rate gas wells. These effects may mask the presence of fractures around the wellbores of naturally fractured reservoirs and may render the effective fracture conductivity and fracture half-length of hydraulically fractured wells much less than the designed parameters. Even though the effects of non-Darcy flow have been identified in the field and properly acknowledged in the well testing literature, little has been done to improve the well test analysis results. This paper presents a new technique that accurately determines the fracture conductivity of hydraulically fractured gas wells producing at constant-bottomhole pressure and provides direct means to calculate the magnitude of turbulence in the fracture around the wellbore from a single well test. A semi-analytical equation that incorporates the effects of non-Darcy flow in the fracture is presented for the first time. A detailed investigation of the various parameters that influence the flow behavior of real gas in the fracture nearby the wellbore is also illustrated. Furthermore, a systematic method for calculating the fracture conductivity and non-Darcy flow coefficient from a single well test is outlined. The final working equations are presented in such a way that permits a straightforward, simple, yet accurate analysis of the variable flow rate with time. No type-curve matching, multirate tests or correlations are required. The methodology of the proposed technique is illustrated using several synthetic examples. (author)

  9. Nanoduct Sweat Conductivity Measurements in 2664 Patients: Relationship to Age, Arterial Blood Gas, Serum Electrolyte Profiles and Clinical Diagnosis

    Science.gov (United States)

    Sezer, Rabia Gonul; Aydemir, Gokhan; Akcan, Abdullah Baris; Paketci, Cem; Karaoglu, Abdulbaki; Aydinoz, Secil; Bozaykut, Abdulkadir

    2013-01-01

    Background The Nanoduct® device has acceptable diagnostic accuracy, but there is not enough systematic data supporting its usage in the diagnosis of cystic fibrosis (CF). Methods A retrospective review of patients with an indication for the sweat test was conducted. The conductivity test was repeated in patients who had values higher than 60 mmol/L, and they were referred for sweat chloride measurements. Associations between sweat conductivity measurements and age, gender, (pH, HCO3, pCO2, Na, K, Cl), family history, consanguinity, indications for the test and number of hospitalization were studied. Results Among 2,664 patients, 16 children had sweat conductivity values higher than 80. The median age of patients diagnosed with CF was 4 months old. Age, pH, HCO3, Na, Cl, K and the sweat conductivity test were statistically related (P conductivity test and the sweat test. Conclusions Patients suspected to have CF can be screened using the Nanoduct® conductivity device in non-qualified centers. PMID:23390474

  10. Neutron residual stress measurements in linepipe

    Science.gov (United States)

    Law, Michael; Gnaëpel-Herold, Thomas; Luzin, Vladimir; Bowie, Graham

    2006-11-01

    Residual stresses in gas pipelines are generated by manufacturing and construction processes and may affect the subsequent pipe integrity. In the present work, the residual stresses in eight samples of linepipe were measured by neutron diffraction. Residual stresses changed with some coating processes. This has special implications in understanding and mitigating stress corrosion cracking, a major safety and economic problem in some gas pipelines.

  11. Neutron residual stress measurements in linepipe

    International Nuclear Information System (INIS)

    Law, Michael; Gnaepel-Herold, Thomas; Luzin, Vladimir; Bowie, Graham

    2006-01-01

    Residual stresses in gas pipelines are generated by manufacturing and construction processes and may affect the subsequent pipe integrity. In the present work, the residual stresses in eight samples of linepipe were measured by neutron diffraction. Residual stresses changed with some coating processes. This has special implications in understanding and mitigating stress corrosion cracking, a major safety and economic problem in some gas pipelines

  12. An electron conductive polymer, poly-aniline, in gas separation: optimisation of transport properties by alternated acid-base treatment

    International Nuclear Information System (INIS)

    Rebattet, Laurence

    1994-01-01

    The objective of this research thesis is to study the variation of gas permeation properties of poly-aniline during a doping/de-doping/re-doping cycle, and to study the evolution of the separation power of this polymer. Scanning electronic microscopy is used to study the microstructure and more particularly how the doping agent is distributed within the polymer. Permeabilities, diffusion coefficients, sorption solubilities and interaction energies are measured by using coupled permeation and micro-gravimetry-calorimetry methods. A range of gases (H 2 , O 2 , CO 2 , N 2 , CH 4 ) is analysed [fr

  13. Determination of low-level agricultural residues in soft drinks and sports drinks by gas chromatography with mass-selective detection: single-laboratory validation.

    Science.gov (United States)

    Paske, Nathan; Berry, Bryan; Schmitz, John; Sullivan, Darryl

    2007-01-01

    In this study, sponsored by PepsiCo Inc., a method was validated for measurement of 19 pesticide residues in soft drinks and sports drinks by gas chromatography/mass spectrometry (GC/MS) with mass selective detection The pesticide residues determined in this validation were alpha-benzenehexachloride (BHC); beta-BHC; gamma-BHC; delta-BHC; methyl parathion; malathion; chlorpyrifos; aldrin; 2,4-dichlorodiphenyldichloroethylene (DDE); alpha-endosulfan; 4,4-DDE; 2,4-dichlorodiphenyldichloroethane (DDD); dieldrin; ethion; 4,4-DDD; 2,4-dichlorodiphenyltrichloroethylene (DDT); beta-endosulfan; 4,4-DDT; and endosulfan sulfate when spiked into a 200 mL matrix sample at 0.50 microg/L. The samples were diluted with acetonitrile and water, then liquid-liquid phase extracted into petroleum ether. The resulting extract was concentrated to near dryness and diluted with hexane:dichloromethane (50:50). The concentrated samples were purified by gel permeation chromatography. The resulting solution was concentrated and separated on a Florisil substrate. The eluent was concentrated to near dryness, reconstituted to produce a 200-fold concentration, and analyzed using a GC/MS instrument operated in the selective ion monitoring mode. The GC/MS instrument was equipped with a large volume injector capable of injecting 25 microL. External standards prepared in dichloromethane were used for quantification without the need for matrix-matched calibration because the extraction step minimized the matrix effects. The calibration curves for all agricultural residues had coefficients of determination (r2) of greater than or equal to 0.9900, with the exception of one value that was 0.988. Fortification spikes at 0.50 microg/L in 3 matrixes (7UP, Gatorade, and Diet Pepsi) over the course of 2 days (4 days for Gatorade), where n=8 each day, yielded average percent recoveries (and percent relative standard deviations) as follows (n=64): 95.6 (24.8) for alpha-BHC; 91.9 (23.6) for beta-BHC; 89.1 (21

  14. Development and comparison of two multi-residue methods for the analysis of select pesticides in honey bees, pollen, and wax by gas chromatography-quadrupole mass spectrometry.

    Science.gov (United States)

    Li, Yuanbo; Kelley, Rebecca A; Anderson, Troy D; Lydy, Michael J

    2015-08-01

    One of the hypotheses that may help explain the loss of honey bee colonies worldwide is the increasing potential for exposure of honey bees to complex mixtures of pesticides. To better understand this phenomenon, two multi-residue methods based on different extraction and cleanup procedures have been developed, and compared for the determination of 11 relevant pesticides in honey bees, pollen, and wax by gas chromatography-quadrupole mass spectrometry. Sample preparatory methods included solvent extraction followed by gel permeation chromatography (GPC) cleanup and cleanup using a dispersive solid-phase extraction with zirconium-based sorbents (Z-Sep). Matrix effects, method detection limits, recoveries, and reproducibility were evaluated and compared. Method detection limits (MDL) of the pesticides for the GPC method in honey bees, pollen, and wax ranged from 0.65 to 5.92 ng/g dw, 0.56 to 6.61 ng/g dw, and 0.40 to 8.30 ng/g dw, respectively, while MDLs for the Z-Sep method were from 0.33 to 4.47 ng/g dw, 0.42 to 5.37 ng/g dw, and 0.51 to 5.34 ng/g dw, respectively. The mean recoveries in all matrices and at three spiking concentrations ranged from 64.4% to 149.5% and 71.9% to 126.2% for the GPC and Z-Sep methods, with relative standard deviation between 1.5-25.3% and 1.3-15.9%, respectively. The results showed that the Z-Sep method was more suitable for the determination of the target pesticides, especially chlorothalonil, in bee hive samples. The Z-Sep method was then validated using a series of field-collected bee hive samples taken from honey bee colonies in Virginia. Copyright © 2015 Elsevier B.V. All rights reserved.

  15. Calculation of the thermal conductivity of low-density CH4-N2 gas mixtures using an improved kinetic theory approach.

    Science.gov (United States)

    Hellmann, Robert; Bich, Eckard; Vesovic, Velisa

    2016-04-07

    The thermal conductivity of low-density CH4-N2 gas mixtures has been calculated by means of the classical trajectory method using state-of-the-art intermolecular potential energy surfaces for the CH4-CH4, N2-N2, and CH4-N2 interactions. Results are reported in the temperature range from 70 K to 1200 K. Since the thermal conductivity is influenced by the vibrational degrees of freedom of the molecules, which are not included in the rigid-rotor classical trajectory computations, a new correction scheme to account for vibrational degrees of freedom in a dilute gas mixture is presented. The calculations show that the vibrational contribution at the highest temperature studied amounts to 46% of the total thermal conductivity of an equimolar mixture compared to 13% for pure nitrogen and 58% for pure methane. The agreement with the available experimental thermal conductivity data at room temperature is good, within ±1.4%, whereas at higher temperatures, larger deviations up to 4.5% are observed, which can be tentatively attributed to deteriorating performance of the measuring technique employed. Results are also reported for the magnitude and temperature dependence of the rotational collision number, Z(rot), for CH4 relaxing in collisions with N2 and for N2 relaxing in collisions with CH4. Both collision numbers increase with temperature, with the former being consistently about twice the value of the latter.

  16. Potential use of only Yb2O3in producing dense Si3N4ceramics with high thermal conductivity by gas pressure sintering.

    Science.gov (United States)

    Zhu, Xinwen; Zhou, You; Hirao, Kiyoshi; Ishigaki, Takamasa; Sakka, Yoshio

    2010-12-01

    Yb 2 O 3 is an efficient sintering additive for enhancing not only thermal conductivity but also the high-temperature mechanical properties of Si 3 N 4 ceramics. Here we report the fabrication of dense Si 3 N 4 ceramics with high thermal conductivity by the gas pressure sintering of α-Si 3 N 4 powder compacts, using only Yb 2 O 3 as an additive, at 1900 °C under a nitrogen pressure of 1 MPa. The effects of Yb 2 O 3 content, sample packing condition and sintering time on the densification, microstructure and thermal conductivity were investigated. Curves of the density plotted against the Yb 2 O 3 content exhibited a characteristic ' N ' shape with a local minimum at 3 mol% Yb 2 O 3 and nearly complete densification below and above this concentration. The effects of the sample packing condition on the densification, microstructure and thermal conductivity strongly depended on the Yb 2 O 3 content. The embedded condition led to more complete densification but also to a decrease in thermal conductivity from 119 to 94 W m -1 K -1 upon 1 mol% Yb 2 O 3 addition. The sample packing condition had little effect on the density and thermal conductivity (102-106 W m -1 K -1 ) at 7 mol% Yb 2 O 3 . The thermal conductivity value was strongly related to the microstructure.

  17. Potential use of only Yb2O3 in producing dense Si3N4 ceramics with high thermal conductivity by gas pressure sintering

    Directory of Open Access Journals (Sweden)

    Xinwen Zhu, You Zhou, Kiyoshi Hirao, Takamasa Ishigaki and Yoshio Sakka

    2010-01-01

    Full Text Available Yb2O3 is an efficient sintering additive for enhancing not only thermal conductivity but also the high-temperature mechanical properties of Si3N4 ceramics. Here we report the fabrication of dense Si3N4 ceramics with high thermal conductivity by the gas pressure sintering of α-Si3N4 powder compacts, using only Yb2O3 as an additive, at 1900 °C under a nitrogen pressure of 1 MPa. The effects of Yb2O3 content, sample packing condition and sintering time on the densification, microstructure and thermal conductivity were investigated. Curves of the density plotted against the Yb2O3 content exhibited a characteristic 'N' shape with a local minimum at 3 mol% Yb2O3 and nearly complete densification below and above this concentration. The effects of the sample packing condition on the densification, microstructure and thermal conductivity strongly depended on the Yb2O3 content. The embedded condition led to more complete densification but also to a decrease in thermal conductivity from 119 to 94 W m-1 K−1 upon 1 mol% Yb2O3 addition. The sample packing condition had little effect on the density and thermal conductivity (102–106 W m−1 K−1 at 7 mol% Yb2O3. The thermal conductivity value was strongly related to the microstructure.

  18. Electric characteristics of thin films and gas sensors with varying conductivity: from purely organic materials to nano-composite architectures

    International Nuclear Information System (INIS)

    Pradeau, Jean Paul

    1998-01-01

    This research thesis reports a work which aimed at producing active molecular devices which could be used for gas detection, and which notably display better electric characteristics than existing ones. The author first outlines that these devices present a high sensitivity, and then discusses why they display these reliability problems in terms of electric characteristics. Thus, he studied the influence of the electrode/material interface, and the influence of the material thickness on measured electric characteristics. He highlighted the non negligible influence of a control of physical-chemical properties of the electrode/material interface on the measurement of electric characteristics. Then, in order to solve these problems, the author proposes and reports the study of a mixing, within the same material, of organic molecules (for detection purposes) and metallic particles (for transduction purposes) [fr

  19. Geophysical exploration to estimate the surface conductivity of residual argillaceous bands in the groundwater repositories of coastal sediments of EOLGA, Nigeria

    Directory of Open Access Journals (Sweden)

    N.J. George

    2017-06-01

    Full Text Available Electrical geophysical applications exploit a petrophysical relationship governing the electrical properties of rocks/sediments when field data are coupled with laboratory data. Given the robust analytical techniques of electrical method and the interrelationship with laboratory measurements, it seems natural to classify, and hence simplify, the spatially aggregated conductivity information on the basis of rock/sediment lithology. This provides a unique link between lithological sediment/rock parameters and the physical parameters controlling bulk conductivity. In this work vertical electrical sounding (VES technique employing Schlumberger configuration integrated with sediment and water analysis have been used to determine the conductivity of argillaceous bands of aquifer sands (fine- coarse sands in Eastern Obolo Local Government Area (EOLGA. The analysis of the data shows that the aquifer systems composing of fine sands, siltstones and coarse sand have bulk and pore-water resistivities ranging from 40.1–2049.4 Ω m (average = 995.18 Ω m to 2.7–256.9 Ω m (average = 91.2 Ω m respectively. These ranges respectively correspond to porosity and formation factor of (19.5–40.6%; average = 29.2% and (7.1–19.7%; average = 12.95%. Within the limit of experimental errors clearly specified in the work, the intrinsic (clay-free formation factor (Fi was estimated to be 16.34 while the intrinsic porosity and the conductivity of the pore-scale clay (σA were respectively estimated to be 20.4% and 3.2679 mS/m. Accounting for this conductivity magnitude of argillaceous bands from bulk conductivity (σb of aquifer sands makes the aquifer systems in the area to be consistent with Archie’s law that is valid only in clay-free sandy formation. The graphical deductions and contour distribution of parameters realised from data processing could be used to derive input parameters for contaminant migration modelling and to improve the

  20. Preparation, Characterization and Sensitive Gas Sensing of Conductive Core-sheath TiO(2)-PEDOT Nanocables.

    Science.gov (United States)

    Wang, Ying; Jia, Wenzhao; Strout, Timothy; Ding, Yu; Lei, Yu

    2009-01-01

    Conductive core-sheath TiO(2)-PEDOT nanocables were prepared using electrospun TiO(2) nanofibers as template, followed by vapor phase polymerization of EDOT. Various techniques were employed to characterize the sample. The results reveal that the TiO(2) core has an average diameter of ∼78 nm while the PEDOT sheath has a uniform thickness of ∼6 nm. The as-prepared TiO(2)-PEDOT nanocables display a fast and reversible response to gaseous NO(2) and NH(3) with a limit of detection as low as 7 ppb and 675 ppb (S/N=3), respectively. This study provides a route for the synthesis of conductive nanostructures which show excellent performance for sensing applications.

  1. Preparation, Characterization and Sensitive Gas Sensing of Conductive Core-sheath TiO2-PEDOT Nanocables

    Science.gov (United States)

    Wang, Ying; Jia, Wenzhao; Strout, Timothy; Ding, Yu; Lei, Yu

    2009-01-01

    Conductive core-sheath TiO2-PEDOT nanocables were prepared using electrospun TiO2 nanofibers as template, followed by vapor phase polymerization of EDOT. Various techniques were employed to characterize the sample. The results reveal that the TiO2 core has an average diameter of ∼78 nm while the PEDOT sheath has a uniform thickness of ∼6 nm. The as-prepared TiO2-PEDOT nanocables display a fast and reversible response to gaseous NO2 and NH3 with a limit of detection as low as 7 ppb and 675 ppb (S/N=3), respectively. This study provides a route for the synthesis of conductive nanostructures which show excellent performance for sensing applications. PMID:22423197

  2. Preparation, Characterization and Sensitive Gas Sensing of Conductive Core-sheath TiO2-PEDOT Nanocables

    Directory of Open Access Journals (Sweden)

    Yu Lei

    2009-08-01

    Full Text Available Conductive core-sheath TiO2-PEDOT nanocables were prepared using electrospun TiO2 nanofibers as template, followed by vapor phase polymerization of EDOT. Various techniques were employed to characterize the sample. The results reveal that the TiO2 core has an average diameter of ~78 nm while the PEDOT sheath has a uniform thickness of ~6 nm. The as-prepared TiO2-PEDOT nanocables display a fast and reversible response to gaseous NO2 and NH3 with a limit of detection as low as 7 ppb and 675 ppb (S/N=3, respectively. This study provides a route for the synthesis of conductive nanostructures which show excellent performance for sensing applications.

  3. Large-time behavior of the motion of a viscous heat-conducting one-dimensional gas coupled to radiation

    Czech Academy of Sciences Publication Activity Database

    Ducomet, B.; Nečasová, Šárka

    2012-01-01

    Roč. 191, č. 2 (2012), s. 219-260 ISSN 0373-3114 R&D Projects: GA ČR GA201/08/0012 Institutional research plan: CEZ:AV0Z10190503 Keywords : compressible * viscous * heat -conducting Subject RIV: BA - General Mathematics Impact factor: 0.680, year: 2012 http://www.springerlink.com/content/0gw2j0311w430012/

  4. Correction factor to determine total hydrogen+deuterium concentration obtained by inert gas fusion-thermal conductivity detection (IGF- TCD) technique

    International Nuclear Information System (INIS)

    Ramakumar, K.L.; Sesha Sayi, Y.; Shankaran, P.S.; Chhapru, G.C; Yadav, C.S.; Venugopal, V.

    2004-01-01

    The limitation of commercially available dedicated equipment based on Inert Gas Fusion- Thermal Conductivity Detection (IGF - TCD) for the determination of hydrogen+deuterium is described. For a given molar concentration, deuterium is underestimated vis a vis hydrogen because of lower thermal conductivity and not considering its molecular weight in calculations. An empirical correction factor based on the differences between the thermal conductivities of hydrogen, deuterium and the carrier gas argon, and the mole fraction of deuterium in the sample has been derived to correct the observed hydrogen+deuterium concentration. The corrected results obtained by IGF - TCD technique have been validated by determining hydrogen and deuterium contents in a few samples using an independent method based on hot vacuum extraction-quadrupole mass spectrometry (HVE-QMS). Knowledge of mole fraction of deuterium (XD) is necessary to effect the correction. The correction becomes insignificant at low X D values (XD < 0.2) as the precision in the IGF measurements is comparable with the extent of correction. (author)

  5. CO2Explorer: Conducting Greenhouse-Gas Measurements of Landfills using a Small Fixed-wing UAV

    Science.gov (United States)

    Hollingsworth, Peter; Allen, Grant; Kabbabe, Khristopher; Pitt, Joseph

    2017-04-01

    Quantifying inventories of Greenhouse gas emissions, primarily Methane and Carbon Dioxide, from distributed sources such as a landfill has historically been undertaken using one of several ground based measurement techniques. These methods are either time and/or resource intensive. As a result regulatory agencies have started looking at the potential of using small-unmanned aircraft to supplement or supplant the current methods. The challenge of using a UAV to perform these tasks is the trade-off between accuracy, operational flexibility and operational productivity. This is driven by the state-of-the-art in measurement instruments, the operating environment at landfills and the regulatory/safety environment surrounding UAV operations. This work describes the development of the operational concept, and associated UAV measurement platform for the CO2Explorer. It looks at the scientific, engineering and possible policy trades and compares the use of small rotary and fixed-wing UAVs from both an operational and measurement perspective. This work also makes recommendations on system development and operation for users lacking in both systems engineering and operational experience.

  6. Validation of a gas chromatography/thermal conductivity detection method for the determination of the water content of oxygenated solvents.

    Science.gov (United States)

    O'Keefe, W K; Ng, F T T; Rempel, G L

    2008-02-22

    A gas chromatographic (GC) method for the determination of the water content of acetone solutions containing methyl isobutyl ketone (MIBK) and other by-products of MIBK synthesis was developed and validated. Linearity is demonstrated (R2=0.9999) over a broad range of water concentrations in acetone ranging from 0.04 to 15.2% (w/w). The quantitation limit (QL) of this technique was found to be 0.346% (w/w) and the detection limit (DL) was estimated to be 13ppm. Validation of this analytical method's accuracy against a coulometric Karl Fischer titration (KFT) method showed excellent agreement between these two techniques. The GC/TCD method is accurate to within a relative error of 3.49% with respect to the KFT method for water concentration above the QL. However, the analysis of six samples below the QL showed an average relative error of 10.96%. Consequently, the KFT method is recommended for the moisture analysis of samples for water concentrations below 0.35% (w/w). Excellent precision is realized for water concentration above the QL (RSD<0.8%). Good precision (RSD=1.1%) was obtained for the sample with the lowest water concentration investigated (0.04%, w/w). Repeatability, robustness and excellent specificity of this technique are demonstrated.

  7. Changes in the hydrogen-bonding strength of internal water molecules and cysteine residues in the conductive state of channelrhodopsin-1

    Science.gov (United States)

    Lórenz-Fonfría, Víctor A.; Muders, Vera; Schlesinger, Ramona; Heberle, Joachim

    2014-12-01

    Water plays an essential role in the structure and function of proteins, particularly in the less understood class of membrane proteins. As the first of its kind, channelrhodopsin is a light-gated cation channel and paved the way for the new and vibrant field of optogenetics, where nerve cells are activated by light. Still, the molecular mechanism of channelrhodopsin is not understood. Here, we applied time-resolved FT-IR difference spectroscopy to channelrhodopsin-1 from Chlamydomonas augustae. It is shown that the (conductive) P2380 intermediate decays with τ ≈ 40 ms and 200 ms after pulsed excitation. The vibrational changes between the closed and the conductive states were analyzed in the X-H stretching region (X = O, S, N), comprising vibrational changes of water molecules, sulfhydryl groups of cysteine side chains and changes of the amide A of the protein backbone. The O-H stretching vibrations of "dangling" water molecules were detected in two different states of the protein using H218O exchange. Uncoupling experiments with a 1:1 mixture of H2O:D2O provided the natural uncoupled frequencies of the four O-H (and O-D) stretches of these water molecules, each with a very weakly hydrogen-bonded O-H group (3639 and 3628 cm-1) and with the other O-H group medium (3440 cm-1) to moderately strongly (3300 cm-1) hydrogen-bonded. Changes in amide A and thiol vibrations report on global and local changes, respectively, associated with the formation of the conductive state. Future studies will aim at assigning the respective cysteine group(s) and at localizing the "dangling" water molecules within the protein, providing a better understanding of their functional relevance in CaChR1.

  8. Findings of a retrospective survey conducted after the Lodgepole sour gas well blowout to determine if the natural occurrence of bovine abortions and fetal anomalies increased

    International Nuclear Information System (INIS)

    Klavano, G.G.; Christian, R.G.

    1992-01-01

    A survey was conducted after the Lodgepole sour gas well blowout of October 1982 to determine if the incident changed the number and type of bovine abortions and abnormal bovine feti submitted to the diagnostic laboratory from the blowout area. The records of the total number of bovine feti submitted were compared between three areas to determine if there was a significant difference between the areas closer to the well site and the larger total area. No changes or trends could be ascribed to the well blowout. 2 refs., 5 tabs

  9. Structures and electrochemical properties of pyrolytic carbon films infiltrated from gas phase into electro-conductive substrates derived from wood

    International Nuclear Information System (INIS)

    Ohzawa, Yoshimi; Mitani, Masami; Li, Jianling; Nakajima, Tsuyoshi

    2004-01-01

    Using the pressure-pulsed chemical vapor infiltration technique, pyrolytic carbon (pyrocarbon) films were deposited into two sorts of conductive porous substrates, that is, the carbonized wood (A) and the TiN-coated wood (B). Structures and electrochemical properties were investigated as the negative electrodes of lithium-ion secondary battery. The electrodes had the three-dimensionally continuous current paths in the pyrocarbon-based anodes without the organic binders and the additional conductive fillers. The pyrocarbon films adhered tightly to the carbonized wood or TiN as current collector. These macro-structures of electrodes were effective in improving the high rate property. The sort of substrates affected the nano-structure of pyrocarbon. The pyrocarbon in sample (A) had the relatively high crystallinity, whereas the pyrocarbon in sample (B) was disordered. The capacity of pyrocarbon in sample (B) was higher than that of sample (A), reflecting the disordered microstructure of pyrocarbon film (B). However, sample (A) showed higher Coulombic efficiency at first cycle (i.e. 87%) than that of sample (B), which would result from the high crystallinity, laminar microstructure and low surface area of pyrocarbon in sample (A)

  10. The effects of a polyacrylamide-derived water treatment residue on the hydraulic conductivity, water retention and evaporation of four contrasting South African soils and implications for land disposal.

    Science.gov (United States)

    Moodley, M; Hughes, J C

    2006-01-01

    Water treatment residue (WTR), a by-product from the production of potable water, was traditionally disposed of to landfill but there is growing interest in applying this waste to land as an alternative disposal option. Because WTR consists mainly of flocculated fine silt and clay, there is concern that should the residue decompose back to its original constituents, there is an adverse risk for soil water storage and transmission properties of soil. In a laboratory study, four different soil types were amended with a polyacrylamide WTR at rates ranging from 0 to 1280 Mg ha(-1). The treatments were evaluated for changes in water retention, hydraulic conductivity and evaporation. The results showed that WTR decreased bulk density and evaporation and actually increased hydraulic conductivity and water retention, mainly because of the sustained performance of the polymer in binding the silt and clay into gravel-sized aggregates. Such changes were, however, only significant at the 1280 Mg ha(-1) application rate. Therefore, very large amounts of WTR would have to be applied in order to markedly change these inherent physical properties of the soils. In view of this finding, the land treatment of WTR appears possible.

  11. Annual report on compliance with the codes of good conduct and independence of electricity grid and natural gas network operators. November 2005

    International Nuclear Information System (INIS)

    2005-11-01

    In France, system operators belong to groups that also conduct business in the energy sector, in fields governed by competition rules. They could therefore be tempted to use their privileged position to their group's benefit, which would disadvantage end consumers. Non-discriminatory access to electricity and gas transmission and distribution networks is at the core of the market opening to competition approach implemented by the European Union since the end of the 1990's. EU and national enactments in force highlight two tools to ensure nondiscrimination: compliance programmes and independence of system operators with regard to their parent companies. Firstly, compliance programs contain measures taken to ensure that discrimination is completely excluded and that their application is subject to appropriate monitoring. Secondly, system operator independence plays a part in preventing discrimination against competitors with other business activities (generation, supply, etc.) within the same group. In application of these enactments, every electricity or natural gas transmission or distribution system operator serving more than 100,000 customers provided CRE, the Energy Regulatory Commission, with their annual reports on the application of their compliance programs. This document is CRE's November 2005 report about compliance programmes and independence of electricity and natural gas system operators. It has been prepared using the codes of good conduct and the annual reports supplied by network operators. CRE also launched a public consultation of the market players in October 2005 and listened to what the network operators had to say. Moreover, it carried out a certain number of checks on operators' practices

  12. Compaction and gas loss in welded pyroclastic deposits as revealed by porosity, permeability, and electrical conductivity measurements of the Shevlin Park Tuff

    Science.gov (United States)

    Wright, Heather M.; Cashman, Katharine V.

    2014-01-01

    Pyroclastic flows produced by large volcanic eruptions commonly densify after emplacement. Processes of gas escape, compaction, and welding in pyroclastic-flow deposits are controlled by the physical and thermal properties of constituent material. Through measurements of matrix porosity, permeability, and electrical conductivity, we provide a framework for understanding the evolution of pore structure during these processes. Using data from the Shevlin Park Tuff in central Oregon, United States, and from the literature, we find that over a porosity range of 0%–70%, matrix permeability varies by almost 10 orders of magnitude (from 10–20 to 10–11 m2), with over three orders of magnitude variation at any given porosity. Part of the variation at a given porosity is due to permeability anisotropy, where oriented core samples indicate higher permeabilities parallel to foliation (horizontally) than perpendicular to foliation (vertically). This suggests that pore space is flattened during compaction, creating anisotropic crack-like networks, a geometry that is supported by electrical conductivity measurements. We find that the power law equation: k1 = 1.3 × 10–21 × ϕ5.2 provides the best approximation of dominant horizontal gas loss, where k1 = permeability, and ϕ = porosity. Application of Kozeny-Carman fluid-flow approximations suggests that permeability in the Shevlin Park Tuff is controlled by crack- or disk-like pore apertures with minimum widths of 0.3 and 7.5 μm. We find that matrix permeability limits compaction over short times, but deformation is then controlled by competition among cooling, compaction, water resorption, and permeable gas escape. These competing processes control the potential for development of overpressure (and secondary explosions) and the degree of welding in the deposit, processes that are applicable to viscous densification of volcanic deposits in general. Further, the general relationships among porosity, permeability, and

  13. Perda de carga em tubos de PVC conduzindo água residuária do processamento de café Head loss for PVC pipes conducting wasterwater of coffee processing

    Directory of Open Access Journals (Sweden)

    Jacinto de A. Carvalho

    2009-12-01

    Full Text Available Visando determinar a perda de carga distribuída e avaliar a variação dos coeficientes de atrito das equações Universal e de Hazen-Williams em tubulações comerciais de PVC, conduzindo águas residuárias do processamento do café (descascamento e demucilagem, ensaios foram conduzidos no Laboratório de Hidráulica do Departamento de Engenharia da Universidade Federal de Lavras, em que os resultados apontaram aumento do fator de atrito "f" e, conseqüentemente, da perda de carga, de 5 a 35% para águas residuárias da demucilagem e de 2 a 11% para água de descascamento, em relação à água pura, para tubulações de 75 e 25 mm, respectivamente. Ocorreu redução na perda de carga com a diluição das águas residuárias. O coeficiente "C", da equação de Hazen-Williams, variou de 125 (água de demucilagem e diâmetro 25 mm a 148 (água residuária do descascamento e diâmetro 75 mm.Experiments were conducted in the Hydraulics Laboratory of the Federal University of Lavras to determine the head loss and the friction coefficients of the Universal and Hazen-Williams equations in PVC commercials pipes conducting wastewater of coffee processing. The results indicated an increase of the attrition " factor f " and, consequently, of the head loss, from 5 to 35% for despulping wastewater, and from 2 to 11% for peeling wastewater in relation to water, for pipes of 75 and 25 mm respectively; the load loss decreased with the dilution of the wastewaters; the coefficient "C" of the Hazen-Williams equation varied from 125 (despulping wastewater and diameter 25 mm to 148 (peeling wastewater and diameter 75 mm.

  14. A novel approach to determine the in-plane thermal conductivity of gas diffusion layers in proton exchange membrane fuel cells

    Science.gov (United States)

    Sadeghi, E.; Djilali, N.; Bahrami, M.

    Heat transfer through the gas diffusion layer (GDL) is a key process in the design and operation of a proton exchange membrane (PEM) fuel cell. The analysis of this process requires determination of the effective thermal conductivity. This transport property differs significantly in the through-plane and in-plane directions due to the anisotropic micro-structure of the GDL. A novel test bed that allows separation of in-plane effective thermal conductivity and thermal contact resistance in GDLs is described in this paper. Measurements are performed using Toray carbon paper TGP-H-120 samples with varying polytetrafluoroethylene (PTFE) content at a mean temperature of 65-70 °C. The measurements are complemented by a compact analytical model that achieves good agreement with experimental data. The in-plane effective thermal conductivity is found to remain approximately constant, k ≈ 17.5 W m -1 K -1, over a wide range of PTFE content, and its value is about 12 times higher than that for through-plane conductivity.

  15. Rapid and long-term effects of water deficit on gas exchange and hydraulic conductance of silver birch trees grown under varying atmospheric humidity.

    Science.gov (United States)

    Sellin, Arne; Niglas, Aigar; Õunapuu-Pikas, Eele; Kupper, Priit

    2014-03-24

    Effects of water deficit on plant water status, gas exchange and hydraulic conductance were investigated in Betula pendula under artificially manipulated air humidity in Eastern Estonia. The study was aimed to broaden an understanding of the ability of trees to acclimate with the increasing atmospheric humidity predicted for northern Europe. Rapidly-induced water deficit was imposed by dehydrating cut branches in open-air conditions; long-term water deficit was generated by seasonal drought. The rapid water deficit quantified by leaf (ΨL) and branch water potentials (ΨB) had a significant (P exchange parameters, while inclusion of ΨB in models resulted in a considerably better fit than those including ΨL, which supports the idea that stomatal openness is regulated to prevent stem rather than leaf xylem dysfunction. Under moderate water deficit (ΨL≥-1.55 MPa), leaf conductance to water vapour (gL), transpiration rate and leaf hydraulic conductance (KL) were higher (P higher soil water potential in H treatment. Two functional characteristics (gL, KL) exhibited higher (P higher air humidity exhibit higher sensitivity to rapid water deficit with respect to two characteristics - leaf conductance to water vapour and leaf hydraulic conductance. Disproportionate changes in sensitivity of stomatal versus leaf hydraulic conductance to water deficit will impose greater risk of desiccation-induced hydraulic dysfunction on the plants, grown under high atmospheric humidity, in case of sudden weather fluctuations, and might represent a potential threat in hemiboreal forest ecosystems. There is no trade-off between plant hydraulic capacity and photosynthetic water-use efficiency on short time scale.

  16. Residuation theory

    CERN Document Server

    Blyth, T S; Sneddon, I N; Stark, M

    1972-01-01

    Residuation Theory aims to contribute to literature in the field of ordered algebraic structures, especially on the subject of residual mappings. The book is divided into three chapters. Chapter 1 focuses on ordered sets; directed sets; semilattices; lattices; and complete lattices. Chapter 2 tackles Baer rings; Baer semigroups; Foulis semigroups; residual mappings; the notion of involution; and Boolean algebras. Chapter 3 covers residuated groupoids and semigroups; group homomorphic and isotone homomorphic Boolean images of ordered semigroups; Dubreil-Jacotin and Brouwer semigroups; and loli

  17. Analysis of organo-chlorine pesticides residue in raw coffee with a modified "quick easy cheap effective rugged and safe" extraction/clean up procedure for reducing the impact of caffeine on the gas chromatography-mass spectrometry measurement.

    Science.gov (United States)

    Bresin, Bruno; Piol, Maria; Fabbro, Denis; Mancini, Maria Antonietta; Casetta, Bruno; Del Bianco, Clorinda

    2015-01-09

    The control of pesticide residues on raw coffee is a task of great importance due to high consumption of this beverage in Italy and in many other countries. High caffeine content can hamper extraction and measurement of any pesticide residue. A tandem extraction protocol has been devised by exploiting the quick easy cheap effective rugged and safe (QuEChERS) scheme for extraction, coupled to a dispersive liquid-liquid micro-extraction (DLLME) in order to drastically reduce caffeine content in the final extract. Gas chromatography-mass spectrometry (GC-MS) has been used for quantification of organo-chlorine pesticides in single ion monitoring (SIM) mode. Method has been validated and performances meet the criteria prescribed by European Union regulations. Copyright © 2014 Elsevier B.V. All rights reserved.

  18. Development and validation of a multi-residue method for the detection of a wide range of hormonal anabolic compounds in hair using gas chromatography-tandem mass spectrometry

    International Nuclear Information System (INIS)

    Rambaud, Lauriane; Monteau, Fabrice; Deceuninck, Yoann; Bichon, Emmanuelle; Andre, Francois; Le Bizec, Bruno

    2007-01-01

    The monitoring of anabolic steroid residues in hair is undoubtedly one of the most efficient strategies to demonstrate the long-term administration of these molecules in meat production animals. A multi-residue sample preparation procedure was developed and validated for 28 steroids. A 100 mg hair sample was grinded into powder and extracted at 50 deg. C with methanol. After acidic hydrolysis and extraction with ethyl acetate, phenolsteroids, such as estrogens, resorcyclic acid lactones and stilbens in one hand, are separated from androgens and progestagens in the other hand. Solid phase extractions were performed before applying a specific derivatisation for each compound sub-group. Detection and identification were achieved using gas chromatography-tandem mass spectrometry with acquisition in the selected reaction monitoring mode after electron ionisation. The method was validated according to the 2002/657/EC guideline. Decision limits (CCα) for main steroids were in the 0.1-10 μg kg -1 range

  19. A multi-residue method for pesticides analysis in green coffee beans using gas chromatography-negative chemical ionization mass spectrometry in selective ion monitoring mode.

    Science.gov (United States)

    Pizzutti, Ionara R; de Kok, Andre; Dickow Cardoso, Carmem; Reichert, Bárbara; de Kroon, Marijke; Wind, Wouter; Weber Righi, Laís; Caiel da Silva, Rosselei

    2012-08-17

    In this study, a new gas chromatography-mass spectrometry (GC-MS) method, using the very selective negative chemical ionization (NCI) mode, was developed and applied in combination with a modified acetonitrile-based extraction method (QuEChERS) for the analysis of a large number of pesticide residues (51 pesticides, including isomers and degradation products) in green coffee beans. A previously developed integrated sample homogenization and extraction method for both pesticides and mycotoxins analysis was used. An homogeneous slurry of green milled coffee beans and water (ratio 1:4, w/w) was prepared and extracted with acetonitrile/acetic acid (1%), followed by magnesium sulfate addition for phase separation. Aliquots from this extract could be used directly for LC-MS/MS analysis of mycotoxins and LC-amenable pesticides. For GC-MS analysis, a further clean-up was necessary. C18- and PSA-bonded silica were tested as dispersive solid-phase extraction (d-SPE) sorbents, separate and as a mixture, and the best results were obtained using C18-bonded silica. For the optimal sensitivity and selectivity, GC-MS detection in the NCI-selected ion monitoring (SIM) mode had to be used to allow the fast analysis of the difficult coffee bean matrix. The validation was performed by analyzing recovery samples at three different spike concentrations, 10, 20 and 50 μg kg(-1), with 6 replicates (n=6) at each concentration. Linearity (r(2)) of calibration curves, estimated instrument and method limits of detection and limits of quantification (LOD(i), LOD(m), LOQ(i) and LOQ(m), respectively), accuracy (as recovery %), precision (as RSD%) and matrix effects (%) were determined for each individual pesticide. From the 51 analytes (42 parent pesticides, 4 isomers and 5 degradation products) determined by GC-MS (NCI-SIM), approximately 76% showed average recoveries between 70-120% and 75% and RSD ≤ 20% at the lowest spike concentration of 10 μg kg(-1), the target method LOQ. For the

  20. [Plant drugs with residues of organochlorine compounds. 2. Identification of residues of DDT and its analogs by comparison of gas chromatography on packed and capillary columns and GC/MS coupling].

    Science.gov (United States)

    Benecke, R; Brotka, J; Wijsbeek, J; Franke, J P; Bruins, A P; de Zeeuw, R A

    1986-07-01

    For the GC analysis of DDT isomers and metabolites in extracts of Flores Chamomillae end Radix Valerianae the separation on a packed QF-1/OV-17 column was compared with various capillary columns of the CP-Sil type. Identification of the individual compounds could be achieved by comparing the retention behavior, chemical transformation of DDT and DDE, as well as by capillary GC-MS using single ion monitoring of substance-characteristic ion mass. In this way, residues of p,p'-DDT, o,p'-DDE and p,p'-TDE could be identified.

  1. Theoretical reconsiderations when estimating the mesophyll conductance to CO(2) diffusion in leaves of C(3) plants by analysis of combined gas exchange and chlorophyll fluorescence measurements.

    Science.gov (United States)

    Yin, Xinyou; Struik, Paul C

    2009-11-01

    Existing methods to estimate the mesophyll conductance to CO(2) diffusion (g(m)) are often based on combined gas exchange and chlorophyll fluorescence measurements. However, estimations of average g(m) by these methods are often unreliable either because the range of usable data is too narrow or because the estimations are very sensitive to measurement errors. We describe three method variants to estimate g(m), for which a wider range of data are usable. They use curve-fitting techniques, which minimise the sum of squared model deviations from the data for A (CO(2) assimilation rate) or for J (linear electron transport rate). Like the existing approaches, they are all based on common physiological principles assuming that electron transport limits A. The proposed variants were far less sensitive than the existing approaches to 'measurement noise' either created randomly in the generated data set or inevitably existing in real data sets. Yet, the estimates of g(m) from the three variants differed by approximately 15%. Moreover, for each variant, a stoichiometric uncertainty in linear electron transport-limited photosynthesis can cause another 15% difference. Any estimation of g(m) using gas exchange and chlorophyll fluorescence measurements should be considered with caution, especially when g(m) is high.

  2. Rapid analysis of ethanol and water in commercial products using ionic liquid capillary gas chromatography with thermal conductivity detection and/or barrier discharge ionization detection.

    Science.gov (United States)

    Weatherly, Choyce A; Woods, Ross M; Armstrong, Daniel W

    2014-02-26

    Analysis of ethanol and water in consumer products is important in a variety of processes and often is mandated by regulating agencies. A method for the simultaneous quantitation of ethanol and water that is simple, accurate, precise, rapid, and cost-effective is demonstrated. This approach requires no internal standard for the quantitation of both ethanol and water at any/all levels in commercial products. Ionic liquid based gas chromatography (GC) capillary columns are used to obtain a fast analysis with high selectivity and resolution of water and ethanol. Typical run times are just over 3 min. Examination of the response range of water and ethanol with GC, thermal conductivity detection (TCD), and barrier ionization detection (BID) is performed. Quantitation of both ethanol and water in consumer products is accomplished with both TCD and BID GC detectors using a nonlinear calibration. Validation of method accuracy is accomplished by using standard reference materials.

  3. Thermal conductivity measurements in unsaturated hydrate-bearing sediments

    Science.gov (United States)

    Dai, Sheng; Cha, Jong-Ho; Rosenbaum, Eilis J.; Zhang, Wu; Seol, Yongkoo

    2015-08-01

    Current database on the thermal properties of hydrate-bearing sediments remains limited and has not been able to capture their consequential changes during gas production where vigorous phase changes occur in this unsaturated system. This study uses the transient plane source (TPS) technique to measure the thermal conductivity of methane hydrate-bearing sediments with various hydrate/water/gas saturations. We propose a simplified method to obtain thermal properties from single-sided TPS signatures. Results reveal that both volume fraction and distribution of the pore constituents govern the thermal conductivity of unsaturated specimens. Thermal conductivity hysteresis is observed due to water redistribution and fabric change caused by hydrate formation and dissociation. Measured thermal conductivity increases evidently when hydrate saturation Sh > 30-40%, shifting upward from the geometric mean model prediction to a Pythagorean mixing model. These observations envisage a significant drop in sediment thermal conductivity when residual hydrate/water saturation falls below ~40%, hindering further gas production.

  4. Gas exchange by the mesic-origin, arid land plantation species Robinia pseudoacacia under annual summer reduction in plant hydraulic conductance.

    Science.gov (United States)

    Miyazawa, Yoshiyuki; Du, Sheng; Taniguchi, Takeshi; Yamanaka, Norikazu; Kumagai, Tomo'omi

    2018-03-28

    The mesic-origin plantation species Robinia pseudoacacia L. has been successfully grown in many arid land plantations around the world but often exhibits dieback and reduced growth due to drought. Therefore, to explore the behavior of this species under changing environmental conditions, we examined the relationship between ecophysiological traits, gas exchange and plant hydraulics over a 3-year period in trees that experienced reduced plant hydraulic conductance (Gp) in summer. We found that the transpiration rate, stomatal conductance (Gs) and minimum leaf water potential (Ψlmin) decreased in early summer in response to a decrease in Gp, and that Gp did not recover until the expansion of new leaves in spring. However, we did not observe any changes in the leaf area index or other ecophysiological traits at the leaf level in response to this reduction in Gp. Furthermore, model simulations based on measured data revealed that the canopy-scale photosynthetic rate (Ac) was 15-25% higher than the simulated Ac when it was assumed that Ψlmin remained constant after spring but almost the same as the simulated Ac when it was assumed that Gp remained high even after spring. These findings indicate that R. pseudoacacia was frequently exposed to a reduced Gp at the study site but offset its effects on Ac by plastically lowering Ψlmin to avoid experiencing any further reduction in Gp or Gs.

  5. Residue processing

    Energy Technology Data Exchange (ETDEWEB)

    Gieg, W.; Rank, V.

    1942-10-15

    In the first stage of coal hydrogenation, the liquid phase, light and heavy oils were produced; the latter containing the nonliquefied parts of the coal, the coal ash, and the catalyst substances. It was the problem of residue processing to extract from these so-called let-down oils that which could be used as pasting oils for the coal. The object was to obtain a maximum oil extraction and a complete removal of the solids, because of the latter were returned to the process they would needlessly burden the reaction space. Separation of solids in residue processing could be accomplished by filtration, centrifugation, extraction, distillation, or low-temperature carbonization (L.T.C.). Filtration or centrifugation was most suitable since a maximum oil yield could be expected from it, since only a small portion of the let-down oil contained in the filtration or centrifugation residue had to be thermally treated. The most satisfactory centrifuge at this time was the Laval, which delivered liquid centrifuge residue and centrifuge oil continuously. By comparison, the semi-continuous centrifuges delivered plastic residues which were difficult to handle. Various apparatus such as the spiral screw kiln and the ball kiln were used for low-temperature carbonization of centrifuge residues. Both were based on the idea of carbonization in thin layers. Efforts were also being made to produce electrode carbon and briquette binder as by-products of the liquid coal phase.

  6. Residual Stresses In 3013 Containers

    International Nuclear Information System (INIS)

    Mickalonis, J.; Dunn, K.

    2009-01-01

    The DOE Complex is packaging plutonium-bearing materials for storage and eventual disposition or disposal. The materials are handled according to the DOE-STD-3013 which outlines general requirements for stabilization, packaging and long-term storage. The storage vessels for the plutonium-bearing materials are termed 3013 containers. Stress corrosion cracking has been identified as a potential container degradation mode and this work determined that the residual stresses in the containers are sufficient to support such cracking. Sections of the 3013 outer, inner, and convenience containers, in both the as-fabricated condition and the closure welded condition, were evaluated per ASTM standard G-36. The standard requires exposure to a boiling magnesium chloride solution, which is an aggressive testing solution. Tests in a less aggressive 40% calcium chloride solution were also conducted. These tests were used to reveal the relative stress corrosion cracking susceptibility of the as fabricated 3013 containers. Significant cracking was observed in all containers in areas near welds and transitions in the container diameter. Stress corrosion cracks developed in both the lid and the body of gas tungsten arc welded and laser closure welded containers. The development of stress corrosion cracks in the as-fabricated and in the closure welded container samples demonstrates that the residual stresses in the 3013 containers are sufficient to support stress corrosion cracking if the environmental conditions inside the containers do not preclude the cracking process.

  7. Analysis of class 1 residual solvents in pharmaceuticals using headspace-programmed temperature vaporization-fast gas chromatography-mass spectrometry.

    Science.gov (United States)

    Pérez Pavón, José Luis; Del Nogal Sánchez, Miguel; Fernández Laespada, M A Esther; García Pinto, Carmelo; Moreno Cordero, Bernardo

    2007-02-02

    A sensitive method is presented for the fast screening and determination of residual class 1 solvents (1,1-dichloroethene, 1,2-dichloroethane, 1,1,1-trichloroethane, carbon tetrachloride and benzene) in pharmaceutical products. The applicability of a headspace (HS) autosampler in combination with GC equipped with a programmed temperature vaporizer (PTV) and a MS detector is explored. Different injection techniques were compared. The benefits of using solvent vent injection instead of split or splitless-hot injection for the measurement of volatile compounds are shown: better peak shapes, better signal-to-noise ratios, and hence better detection limits. The proposed method is extremely sensitive. The limits of detection ranged from 4.9 ppt (benzene) to 7.9 ppt (1,2-dichloroethane) and precision (measured as the relative standard deviation) was equal to or lower than 12% in all cases. The method was applied to the determination of residual solvents in nine different pharmaceutical products. The analytical performance of the method shows that it is appropriate for the determination of residual class 1 solvents and has much lower detection limits than the concentration limits proposed by the International Conference on Harmonization (ICH) of Technical Requirements for the Registration of Pharmaceuticals for Human Use. The proposed method achieves a clear improvement in sensitivity with respect to conventional headspace methods due to the use of the PTV.

  8. A rapid, solid phase extraction (SPE technique for the extraction and gas chromatographic determination lindane pesticide residue in tissue and milk

    Directory of Open Access Journals (Sweden)

    Yuningsih

    2006-03-01

    Full Text Available Organochlorine pesticide contamination in feed can cause residue in animal product (tissue and milk, so its become a problem in food safety. Solid phase extraction (SPE has been carried out for determination organochlorine pesticide residues in food animal production. The technique was rapid, not costly and produce limited amount of hazardous-waste. Samples were homogenized with acetonitrile trough cartridge C18, eluted in fluorocyl column with 2% ether-petroleum or acetonitrile fortissue and milk samples respectively. The recoveries of tissue sample by addition lindane standard solution: 0.50 and 1.00 μg are 85.10 and 103.10% respectively, while that of milk with the addition of 0.50, 1.00 and 1.50 μg are 83.80, 88.69 and 91.24% respectively. Three replicates were carried out for every sample. According of validation criteria of FAO/IAEA the recovery for analysis of pesticide residues was 70-110%. Therefore, the method is applicable.

  9. Rapid analytical method for the determination of pesticide residues in sunflower seeds based on focused microwave-assisted Soxhlet extraction prior to gas chromatography-tandem mass spectrometry.

    Science.gov (United States)

    Prados-Rosales, R C; Luque García, J L; Luque de Castro, M D

    2003-04-18

    A rapid analytical method for determination of organochlorine pesticide residues in sunflower seeds based on focused microwave-assisted Soxhlet extraction has been developed. The main factors affecting the extraction efficiency--namely microwave power, irradiation time, volume of extractant and number of cycles--were optimized by a two-level factorial fractional design. After extraction, a liquid-liquid extraction and a clean-up step including the use of Florisil macrocolumns were required prior to injection of the extracts into the chromatograph in order to isolate the pesticide residues from the lipid fraction of the original extract. The MS-MS ion preparation mode was selected due to the high sensitivity and selectivity it provides. Seed samples were used collected near a crop subjected to aerial pesticide application. Residues of hexachlorocyclohexane isomers and endosulfan were found in the seeds although they were not subjected to pesticide application, thus showing the spray-drift contamination. The validation of the proposed approach was carried out by comparison with the ISO 659-1988 reference extraction method obtaining similar, or even better efficiencies by the proposed approach.

  10. Wood ethanol and synthetic natural gas pathways

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2006-11-30

    This report provided details of updates to the wood ethanol pathway recently added to the GHGenius model, an analytical tool used to analyze emissions from conventional and alternative fuel combustion processes. The pathway contains data developed by the United States Department of Energy. A number of co-products were added to the wood and agricultural residue pathways, including furfural, xylitol, lignin, and glycerol. New chemical inputs included nitrogen gas, ammonia, enzymes and yeast. Biological ethanol pathways were reviewed, and separate inputs for wood, agricultural residues, corn ethanol, and wheat ethanol were added. The model was updated to reflect current research conducted on the gasification of wood and the upgrading of the gas to produce pipeline quality natural gas. New process developments in producing pipeline quality gas from coal were also added. The ability to model enzyme consumption was added to all ethanol pathways. 25 refs., 41 tabs., 8 figs.

  11. Wood wastes and residues generated along the Colorado Front Range as a potential fuel source

    Science.gov (United States)

    Julie E. Ward; Kurt H. Mackes; Dennis L. Lynch

    2004-01-01

    Throughout the United States there is interest in utilizing renewable fuel sources as an alternative to coal and nat-ural gas. This project was initiated to determine the availability of wood wastes and residues for use as fuel in ce-ment kilns and power plants located along the Colorado Front Range. Research was conducted through literature searches, phone surveys,...

  12. Management of NORM Residues

    International Nuclear Information System (INIS)

    2013-06-01

    The IAEA attaches great importance to the dissemination of information that can assist Member States in the development, implementation, maintenance and continuous improvement of systems, programmes and activities that support the nuclear fuel cycle and nuclear applications, and that address the legacy of past practices and accidents. However, radioactive residues are found not only in nuclear fuel cycle activities, but also in a range of other industrial activities, including: - Mining and milling of metalliferous and non-metallic ores; - Production of non-nuclear fuels, including coal, oil and gas; - Extraction and purification of water (e.g. in the generation of geothermal energy, as drinking and industrial process water; in paper and pulp manufacturing processes); - Production of industrial minerals, including phosphate, clay and building materials; - Use of radionuclides, such as thorium, for properties other than their radioactivity. Naturally occurring radioactive material (NORM) may lead to exposures at some stage of these processes and in the use or reuse of products, residues or wastes. Several IAEA publications address NORM issues with a special focus on some of the more relevant industrial operations. This publication attempts to provide guidance on managing residues arising from different NORM type industries, and on pertinent residue management strategies and technologies, to help Member States gain perspectives on the management of NORM residues

  13. Fungicide and insecticide residues in rice grains

    Directory of Open Access Journals (Sweden)

    Gustavo Mack Teló

    2017-01-01

    Full Text Available The objective of this study was to analyse residues of fungicides and insecticides in rice grains that were subjected to different forms of processing. Field work was conducted during three crop seasons, and fungicides and insecticides were applied at different crop growth stages on the aerial portion of the rice plants. Azoxystrobin, difenoconazole, propiconazole, tebuconazole, and trifloxystrobin fungicides were sprayed only once at the R2 growth stage or twice at the R2 and R4 growth stages; cypermethrin, lambda-cyhalothrin, permethrin, and thiamethoxam insecticides were sprayed at the R2 growth stage; and permethrin was sprayed at 5-day intervals from the R4 growth stage up to one day prior to harvest. Pesticide residues were analysed in uncooked, cooked, parboiled, polished and brown rice grains as well as rice hulls during the three crop seasons, for a total of 1458 samples. The samples were analysed by gas chromatography with electron capture detection (GC-ECD using modified QuEChERS as the extraction method. No fungicide or insecticide residues were detected in rice grain samples; however, azoxystrobin and cypermethrin residues were detected in rice hull samples.

  14. Design of a compressed air modulator to be used in comprehensive multidimensional gas chromatography and its application in the determination of pesticide residues in grapes

    NARCIS (Netherlands)

    Pizzutti, I.R.; Vreuls, J.J.; Kok, A; Roehrs, R.; Martel, S.; Friggi, C.A.; Zanella, R.

    2009-01-01

    In this study, a new modulator that is simple, robust and presents low operation costs, was developed. This modulator uses compressed air to cool two small portions in the first centimeters of the second chromatographic column of a comprehensive multidimensional gas chromatography (GC × GC) system.

  15. Effect of processing conditions on residual stress distributions by bead-on-plate welding after surface machining

    International Nuclear Information System (INIS)

    Ihara, Ryohei; Mochizuki, Masahito

    2014-01-01

    Residual stress is important factor for stress corrosion cracking (SCC) that has been observed near the welded zone in nuclear power plants. Especially, surface residual stress is significant for SCC initiation. In the joining processes of pipes, butt welding is conducted after surface machining. Residual stress is generated by both processes, and residual stress distribution due to surface machining is varied by the subsequent butt welding. In previous paper, authors reported that residual stress distribution generated by bead on plate welding after surface machining has a local maximum residual stress near the weld metal. The local maximum residual stress shows approximately 900 MPa that exceeds the stress threshold for SCC initiation. Therefore, for the safety improvement of nuclear power plants, a study on the local maximum residual stress is important. In this study, the effect of surface machining and welding conditions on residual stress distribution generated by welding after surface machining was investigated. Surface machining using lathe machine and bead on plate welding with tungsten inert gas (TIG) arc under various conditions were conducted for plate specimens made of SUS316L. Then, residual stress distributions were measured by X-ray diffraction method (XRD). As a result, residual stress distributions have the local maximum residual stress near the weld metal in all specimens. The values of the local maximum residual stresses are almost the same. The location of the local maximum residual stress is varied by welding condition. It could be consider that the local maximum residual stress is generated by same generation mechanism as welding residual stress in surface machined layer that has high yield stress. (author)

  16. Using landfill gas as the primary fuel for a 200 WTPD thermal dryer[Held jointly with the 4. Canadian organic residuals and biosolids managment conference

    Energy Technology Data Exchange (ETDEWEB)

    Shulmister, D. [Manattee County, Manatee, FL (United States). Wastewater Division; Monroe, A. [McKim and Creed, Cary, NC (United States)

    2007-07-01

    Although there is no evidence of health problems, there is a growing opposition to class B land application of biosolids in many localities in the United States, resulting in less sites available to dispose of class B biosolids. Manatee County, located on the West Coast of Florida, decided to implement thermal drying of its biosolids. This produced a class A pellet that could be used without restriction as a fertilizer or soil amendment. The dryer will be located at the county's southeast water reclamation facility, adjacent to the county's Lena Road landfill. The methane gas from the landfill will be used as the primary fuel for the dryer. This paper presented how Manatee County, Florida decided to meet its long term biosolids handling and disposal needs. The paper provided background information on Manatee County, Florida. It discussed the reasons for the dryer technology selection, location of the dryer, sizing criteria as well as listing the components of the dryer. The paper also discussed dryer procurement. Other topics that were presented included fuel requirements and an analysis of landfill gas. The County expects to save approximately two million dollars per year by selecting landfill gas from its Lena Road landfill as the primary fuel for the dryer. 5 tabs.

  17. Residual risk

    African Journals Online (AJOL)

    ing the residual risk of transmission of HIV by blood transfusion. An epidemiological approach assumed that all HIV infections detected serologically in first-time donors were pre-existing or prevalent infections, and that all infections detected in repeat blood donors were new or incident infections. During 1986 - 1987,0,012%.

  18. Gas chromatography and isotope ratio mass spectrometry of Pinot Noir wine volatile compounds (δ13C) and solid residues (δ13C, δ15N) for the reassessment of vineyard water-status.

    Science.gov (United States)

    Spangenberg, Jorge E; Vogiatzaki, Maria; Zufferey, Vivian

    2017-09-29

    This paper describes a novel approach to reassess the water status in vineyards based on compound-specific isotope analysis (CSIA) of wine volatile organic compounds (δ 13 C VOC/VPDB ) and bulk carbon and nitrogen isotopes, and the C/N molar ratios of the wine solid residues (δ 13 C SR/VPDB , δ 15 N SR/Air-N2 ). These analyses link gas chromatography/combustion and elemental analysis to isotope ratio mass spectrometry (GC/C/IRMS, EA/IRMS). Field-grown cultivars of Pinot Noir grapevines were exposed during six growing seasons (2009-2014) to controlled soil water availability, while maintaining identical the other environmental variables and agricultural techniques. Wines were produced from the grapes by the same oenological protocol. This permitted for the assessment of the effects in the biochemistry of wines solely induced by the changes in the plant-soil water status. This mimicked the more recurrent and prolonged periods of soil water deficiency due to climate changes. Water stress in grapevine was assessed by the measurement of the predawn leaf water potential (Ψ pd ) and the stable carbon isotope composition of the berry sugars during harvest (must sugars). For quantitation purposes and the normalization of the measured stable carbon isotope ratios of the VOCs, the wine samples were spiked with three standard compounds with known concentration and δ 13 C VPDB values. VOCs were extracted by liquid-liquid extraction and analyzed by gas chromatography/flame ionization detection (GC/FID), gas chromatography/mass spectrometry (GC/MS), and GC/C/IRMS. δ 13 C values were obtained for eighteen VOCs. The solid residues were obtained by freeze-drying wine aliquots and were analyzed for their C and N content and isotope composition by EA/IRMS. All the isotopic ratios (δ 13 C SR , δ 15 N SR , δ 13 C VOC ) are highly correlated with the Ψ pd values, indicating that the proposed gas chromatography and isotope ratio mass spectrometry approach is a useful tool to

  19. Effects of storage and processing on residue levels of chlorpyrifos in soybeans.

    Science.gov (United States)

    Zhao, Liuwei; Ge, Jing; Liu, Fengmao; Jiang, Naiwen

    2014-05-01

    The residue levels of chlorpyrifos in soybeans during storage and processing were investigated. Soybeans were treated with chlorpyrifos aqueous solution and placed in a sealed plastic container. The residue of chlorpyrifos was determined in soybeans at six time points within 0 and 112days during storage and oil processing of the soybeans was conducted. The analysis of the residues of chlorpyrifos was carried out by gas chromatography-mass spectrometry (GC-MS). Results show that the dissipation of chlorpyrifos in soybeans is about 62% during the storage period. Moreover, the carryover of the residues from soybeans into oil is found to be related to the processing methods. Processing factor, which is defined as the ratio of chlorpyrifos residue concentration in oil sample to that in the soybean samples, was 11 and 0.25 after cold and hot pressing, respectively. Copyright © 2013 Elsevier Ltd. All rights reserved.

  20. Methodology for the determination of residues of organophosphorous pesticides in milk of domestic consumption by means of gas chromatography and extraction in solid phase

    International Nuclear Information System (INIS)

    Romero Blanco, Eric; Meza Nunez, Humberto; Poveda Calvo, Vanessa

    2005-01-01

    A new method oriented to the detection and quantification of 15 organophosphate pesticide in raw milk samples for national consumption has been developed by using a gas chromatograph equipped with polydimethylsiloxane capillary column and a nitrogen-phosphorus detector (NPD), in combination with the extraction technique in solid phase (SPE) for the sample cleaning process and pesticide extraction. Recovery percentages obtained were close to 100% and the detection limits obtained were lower than 20 μg/L for 13 of the organophosphates analyzed. Overall, the method showed important improvement as compared to conventional liquid/liquid extraction methodologies. (Author) [es

  1. Composition of carbonization residues

    Energy Technology Data Exchange (ETDEWEB)

    Hupfer; Leonhardt

    1943-11-27

    This report compared the composition of samples from Wesseling and Leuna. In each case the sample was a residue from carbonization of the residues from hydrogenation of the brown coal processed at the plant. The composition was given in terms of volatile components, fixed carbon, ash, water, carbon, hydrogen, oxygen, nitrogen, volatile sulfur, and total sulfur. The result of carbonization was given in terms of (ash and) coke, tar, water, gas and losses, and bitumen. The composition of the ash was given in terms of silicon dioxide, ferric oxide, aluminum oxide, calcium oxide, magnesium oxide, potassium and sodium oxides, sulfur trioxide, phosphorus pentoxide, chlorine, and titanium oxide. The most important difference between the properties of the two samples was that the residue from Wesseling only contained 4% oil, whereas that from Leuna had about 26% oil. Taking into account the total amount of residue processed yearly, the report noted that better carbonization at Leuna could save 20,000 metric tons/year of oil. Some other comparisons of data included about 33% volatiles at Leuna vs. about 22% at Wesseling, about 5 1/2% sulfur at Leuna vs. about 6 1/2% at Leuna, but about 57% ash for both. Composition of the ash differed quite a bit between the two. 1 table.

  2. Development and validation of a multi-residue method for the detection of a wide range of hormonal anabolic compounds in hair using gas chromatography-tandem mass spectrometry

    Energy Technology Data Exchange (ETDEWEB)

    Rambaud, Lauriane [LABERCA, Ecole Nationale Veterinaire de Nantes, Route de Gachet, BP50707, 44307 Nantes Cedex 3 (France); Monteau, Fabrice [LABERCA, Ecole Nationale Veterinaire de Nantes, Route de Gachet, BP50707, 44307 Nantes Cedex 3 (France); Deceuninck, Yoann [LABERCA, Ecole Nationale Veterinaire de Nantes, Route de Gachet, BP50707, 44307 Nantes Cedex 3 (France); Bichon, Emmanuelle [LABERCA, Ecole Nationale Veterinaire de Nantes, Route de Gachet, BP50707, 44307 Nantes Cedex 3 (France); Andre, Francois [LABERCA, Ecole Nationale Veterinaire de Nantes, Route de Gachet, BP50707, 44307 Nantes Cedex 3 (France); Le Bizec, Bruno [LABERCA, Ecole Nationale Veterinaire de Nantes, Route de Gachet, BP50707, 44307 Nantes Cedex 3 (France)]. E-mail: lebizec@vet-nantes.fr

    2007-03-14

    The monitoring of anabolic steroid residues in hair is undoubtedly one of the most efficient strategies to demonstrate the long-term administration of these molecules in meat production animals. A multi-residue sample preparation procedure was developed and validated for 28 steroids. A 100 mg hair sample was grinded into powder and extracted at 50 deg. C with methanol. After acidic hydrolysis and extraction with ethyl acetate, phenolsteroids, such as estrogens, resorcyclic acid lactones and stilbens in one hand, are separated from androgens and progestagens in the other hand. Solid phase extractions were performed before applying a specific derivatisation for each compound sub-group. Detection and identification were achieved using gas chromatography-tandem mass spectrometry with acquisition in the selected reaction monitoring mode after electron ionisation. The method was validated according to the 2002/657/EC guideline. Decision limits (CC{alpha}) for main steroids were in the 0.1-10 {mu}g kg{sup -1} range.

  3. Effect of different formulations on tebuconazole residues in stone fruits.

    Science.gov (United States)

    Lucini, Luigi; Molinari, Gian Pietro

    2009-04-01

    The correlation between pesticide residue levels and formulation of an active substance is often not considered, even if it is reasonable to expect some differences arising from behaviour during dilution and spraying, from adhesion to plant and from degradation. An experimental study to investigate the magnitude of tebuconazole residues as a function of different tebuconazole formulated products was carried out in Italy. The fungicide was applied as wettable powder (WP) and water-dispersible granule (WG) formulations to peach, plum, apricot and nectarine orchards, on four different sites. The fruit samples gained from the field trials were quantitatively analysed by gas chromatography with a nitrogen phosphorus detector (GC/NPD) for tebuconazole residues. Tebuconazole residues in the fruits gained from the plot treated with the WP formulation, 14 days after application, were in the range 0.01-0.07 mg kg(-1), while corresponding residues in the plot treated with the WG formulation were in the range 0.01-0.06 mg kg(-1). No significant differences in the residue levels of tebuconazole could be observed between the trials conducted with the WP and the WG formulation. Copyright (c) 2009 Society of Chemical Industry.

  4. Residual basins

    International Nuclear Information System (INIS)

    D'Elboux, C.V.; Paiva, I.B.

    1980-01-01

    Exploration for uranium carried out over a major portion of the Rio Grande do Sul Shield has revealed a number of small residual basins developed along glacially eroded channels of pre-Permian age. Mineralization of uranium occurs in two distinct sedimentary units. The lower unit consists of rhythmites overlain by a sequence of black shales, siltstones and coal seams, while the upper one is dominated by sandstones of probable fluvial origin. (Author) [pt

  5. Residue analysis of organochlorine pesticides in water and ...

    African Journals Online (AJOL)

    Mr Willims

    2013-05-12

    May 12, 2013 ... residues were performed by injecting 1 µL of purified extract into the injection port of a gas chromatograph with a 63Ni electron capture .... Identification and determination of OCP residues by gas chromatography. A gas chromatograph with ..... Distribution of chlorine- ted pesticides in shellfishes from Lagos ...

  6. Assessing fuel spill risks in polar waters: Temporal dynamics and behaviour of hydrocarbons from Antarctic diesel, marine gas oil and residual fuel oil.

    Science.gov (United States)

    Brown, Kathryn E; King, Catherine K; Kotzakoulakis, Konstantinos; George, Simon C; Harrison, Peter L

    2016-09-15

    As part of risk assessment of fuel oil spills in Antarctic and subantarctic waters, this study describes partitioning of hydrocarbons from three fuels (Special Antarctic Blend diesel, SAB; marine gas oil, MGO; and intermediate grade fuel oil, IFO 180) into seawater at 0 and 5°C and subsequent depletion over 7days. Initial total hydrocarbon content (THC) of water accommodated fraction (WAF) in seawater was highest for SAB. Rates of THC loss and proportions in equivalent carbon number fractions differed between fuels and over time. THC was most persistent in IFO 180 WAFs and most rapidly depleted in MGO WAF, with depletion for SAB WAF strongly affected by temperature. Concentration and composition remained proportionate in dilution series over time. This study significantly enhances our understanding of fuel behaviour in Antarctic and subantarctic waters, enabling improved predictions for estimates of sensitivities of marine organisms to toxic contaminants from fuels in the region. Copyright © 2016 Elsevier Ltd. All rights reserved.

  7. Trace analysis of residual methyl methanesulfonate, ethyl methanesulfonate and isopropyl methanesulfonate in pharmaceuticals by capillary gas chromatography with flame ionization detection.

    Science.gov (United States)

    Li, Weiyong

    2004-08-13

    A capillary gas chromatographic method using flame ionization detection was developed and validated for the trace analysis (ppm level) of methyl methanesulfonate, ethyl methanesulfonate, and isopropyl methanesulfonate in pharmaceutical drug substance. The method utilizes a megabore capillary column with bonded and crosslinked polyethylene glycol stationary phase. A dissolve-and-injection approach was adopted for sample introduction in a splitless mode. The investigated sample solvents include acetonitrile, ethyl acetate, methylene chloride, 1,2-dichloromethane, and toluene. Aqueous mixtures of acetonitrile and water can also be used as sample solvent. A limit of detection of about 1 microg/g (1 ppm) and limit of quantitation of 5 microg/g (5 ppm) were achieved for the mesylate esters in drug substance samples. The method optimization and validation are also discussed in this paper.

  8. Determination of residual 1,4-dioxane in surfactants and cleaning agents using headspace single-drop microextraction followed by gas chromatography-flame ionization detection.

    Science.gov (United States)

    Saraji, M; Shirvani, N

    2017-02-01

    Polyethoxylated surfactants are widely used in the formulation of different cleaning agents such as shampoo, dish washing and hand washing products and lotion formulation. During the production of polyethoxylated surfactants, 1,4-dioxane as a toxic and carcinogenic by-product is formed. A simple low-cost method based on headspace single-drop microextraction combined with gas chromatography-flame ionization detection was developed for the determination of 1,4-dioxane in surfactants and cleaning agents. In this method, 1,4-dioxane was extracted from 8.0 mL sample solution into a microdrop of an organic solvent, and then, it was injected to gas chromatography. The effects of such parameters as the solvent type, salt addition, microdrop volume, stirring rate, equilibrium time, extraction time and the temperature of sample solution on the extraction performance were studied and optimized. An ethoxylated surfactant containing 1,4-dioxane was used as the sample for the optimization of the extraction parameters. The linear range, determination coefficient, limit of detection and relative standard deviation of the method were 0.5-100 μg g -1 , 0.9977, 0.4 μg g -1 and 7.2% (n = 5), respectively. Different real samples including sodium lauryl ether sulphate, sodium lauryl sulphate (SLS), four brands of shampoo, and hand washing and dish washing liquids were analysed by the method. 1,4-Dioxane was detected at the concentration range of 2.4-201 μg g -1 in the samples, except dish washing liquid and SLS. A new method with the merits of simplicity, low cost, low organic solvent consumption, short analysis time, good repeatability and suitable detection limit was developed for the analysis of 1,4-dioxane in surfactants and cleaning agents. © 2016 Society of Cosmetic Scientists and the Société Française de Cosmétologie.

  9. Calibration of a Mass Spectrometer for Analysis of Ultramicro Gas Samples Using a Dynamic Method of Analysis.

    Science.gov (United States)

    1982-08-16

    tubes. Because of device-related constraints that made it necessary to transport ultramicro amounts of gas to the analyzer, a dynamic method of analysis was...as the results of residual gas analyses conducted with production-quality traveling wave tubes, have validated the dynamic method of analysis . (Author)

  10. Low-level Determination of Residual Methyl Methane Sulfonate and Ethyl Methane Sulfonate in Pharmaceuticals by Gas Chromatography with Mass Spectrometry

    Directory of Open Access Journals (Sweden)

    M. Sarat

    2010-01-01

    Full Text Available A capillary gas chromatographic method using mass spectrometric detection was developed and validated for the trace analysis (ppm level of methyl methane sulfonate and ethyl methane sulfonate in pharmaceutical drug substances. The method utilizes a capillary column (DB-624 with 6% cyanopropyl phenyl and 94% dimethyl polysiloxane stationary phase. A dissolve-and-injection approach was adopted for sample introduction in a split less mode. Mixture of (80:20 ratio of methanol and chloroform was used as a diluent or sample solvent. A limit of detection of about 0.17 μg/g (0.17 ppm for methyl methane sulfonate and 0.18 μg/g (0.18 ppm for ethyl methane sulfonate were achieved and limit of quantitation of 0.52 μg/g (0.52 ppm for methyl methane sulfonate and 0.54 μg/g (0.54 ppm for ethyl methane sulfonate were achieved for alkyl sulfonates in drug substance samples.

  11. Determination of triazole pesticide residues in edible oils using air-assisted liquid-liquid microextraction followed by gas chromatography with flame ionization detection.

    Science.gov (United States)

    Farajzadeh, Mir Ali; Feriduni, Behruz; Mogaddam, Mohammad Reza Afshar

    2015-03-01

    In the present study, a rapid, simple, and highly efficient sample preparation method based on air-assisted liquid-liquid microextraction followed by gas chromatography with flame ionization detection was developed for the extraction, preconcentration, and determination of five triazole pesticides (penconazole, hexaconazole, diniconazole, tebuconazole, and triticonazole) in edible oils. Initially, the oil samples were diluted with hexane and a few microliter of a less soluble organic solvent (extraction solvent) in hexane was added. To form fine and dispersed extraction solvent droplets, the mixture of oil sample solution and extraction solvent is repeatedly aspirated and dispersed with a syringe. Under the optimum extraction conditions, the method showed low limits of detection and quantification between 2.2-6.1 and 7.3-20 μg/L, respectively. Enrichment factors and extraction recoveries were in the ranges of 71-96 and 71-96%, respectively. The relative standard deviations for the extraction of 100 and 250 μg/L of each pesticide were less than 5% for intraday (n = 6) and interday (n = 3) precisions. Finally edible oil samples were successfully analyzed using the proposed method, and hexaconazole was found in grape seed oil. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  12. 78 FR 11126 - Receipt of Several Pesticide Petitions Filed for Residues of Pesticide Chemicals in or on Various...

    Science.gov (United States)

    2013-02-15

    ... may be warranted. Additional data may be needed before EPA can make a final determination on these...) purification. Detection and quantitation are conducted by gas chromatograph equipped with nitrogen phosphorus... outlining the ``Method Validation for the Determination of Residues of Halauxifen-methyl Ester, and...

  13. Multi-residue analysis of legacy POPs and emerging organic contaminants in Singapore's coastal waters using gas chromatography-triple quadrupole tandem mass spectrometry.

    Science.gov (United States)

    Zhang, Hui; Bayen, Stéphane; Kelly, Barry C

    2015-08-01

    A gas chromatography-triple quadrupole mass spectrometry (GC-MS/MS) based method was developed for determination of 86 hydrophobic organic compounds in seawater. Solid-phase extraction (SPE) was employed for sequestration of target analytes in the dissolved phase. Ultrasound assisted extraction (UAE) and florisil chromatography were utilized for determination of concentrations in suspended sediments (particulate phase). The target compounds included multi-class hydrophobic contaminants with a wide range of physical-chemical properties. This list includes several polycyclic and nitro-aromatic musks, brominated and chlorinated flame retardants, methyl triclosan, chlorobenzenes, organochlorine pesticides (OCPs) and polychlorinated biphenyls (PCBs). Spiked MilliQ water and seawater samples were used to evaluate the method performance. Analyte recoveries were generally good, with the exception of some of the more volatile target analytes (chlorobenzenes and bromobenzenes). The method is very sensitive, with method detection limits typically in the low parts per quadrillion (ppq) range. Analysis of 51 field-collected seawater samples (dissolved and particulate-bound phases) from four distinct coastal sites around Singapore showed trace detection of several polychlorinated biphenyl congeners and other legacy POPs, as well as several current-use emerging organic contaminants (EOCs). Polycyclic and nitro-aromatic musks, bromobenzenes, dechlorane plus isomers (syn-DP, anti-DP) and methyl triclosan were frequently detected at appreciable levels (2-20,000pgL(-1)). The observed concentrations of the monitored contaminants in Singapore's marine environment were generally comparable to previously reported levels in other coastal marine systems. To our knowledge, these are the first measurements of these emerging contaminants of concern in Singapore or Southeast Asia. The developed method may prove beneficial for future environmental monitoring of hydrophobic organic contaminants

  14. Analyses of organochlorine pesticides residues in eels (Anguilla anguilla from Lake Garda using Gas chromatography coupled with Tandem Mass Spectrometry (GC-MS/MS.

    Directory of Open Access Journals (Sweden)

    Giuseppe Federico Labella

    2017-05-01

    Full Text Available Lake Garda is located in Insubria region, that is known for being the most populated and industrialized area of Italy (Camusso et al., 2001. Therefore, the Lake water, and also the fish species present, could be affected by environmental contamination.  European eel (Anguilla anguilla are considered as suitable matrix for biomonitoring environmental contaminants in European water (Belpaire et al., 2007, being widespread in many European waters and highly contaminated by lipophilic compounds, due to the high lipid content (up to 40% (Larsson et al., 1991. Moreover, eel is an edible species (its farming currently supplies approximately 45,000 tons/year (Nielsen et al., 2008, so it also represents a public health issue. Based on these considerations, the aim of this study was to evaluate the occurrence of fourteen organochlorine pesticides (OCs in forty-five eels (Anguilla anguilla from Lake Garda, using Accelerated Solvent Extraction (ASE procedure for the analytes extraction and Gas chromatography coupled with Tandem Mass Spectrometry (GC-MS/MS for the analysis of OCs. GC-MS/MS analysis was developed and validated according to the SANTE/11945/2015 guidelines.  Uncontaminated eel sample (previously checked for the presence of OCs and considered blank with a concentration of compounds < Limit of Detection were used for all procedure's optimization steps. For all the OCs analysed, satisfactory results were achieved. Regarding eel samples, several pesticides were detected, but DDTs (DDT and its metabolites were found with the highest prevalence (92 %. The concentration rage was from not detected (n.d. to 19000 ng g-1. Although DDTs levels in the environment are declining (Albaiges et al., 2011, they continue to bioaccumulate in tissues of human and animal and biomagnify in food chains.

  15. RESIDUAL RISK ASSESSMENTS - RESIDUAL RISK ...

    Science.gov (United States)

    This source category previously subjected to a technology-based standard will be examined to determine if health or ecological risks are significant enough to warrant further regulation for Coke Ovens. These assesments utilize existing models and data bases to examine the multi-media and multi-pollutant impacts of air toxics emissions on human health and the environment. Details on the assessment process and methodologies can be found in EPA's Residual Risk Report to Congress issued in March of 1999 (see web site). To assess the health risks imposed by air toxics emissions from Coke Ovens to determine if control technology standards previously established are adequately protecting public health.

  16. Electrodialytic remediation of air pollution control residues

    DEFF Research Database (Denmark)

    Jensen, Pernille Erland

    Air pollution control (APC) residue from municipal solid waste incineration (MSWI) consists of the fly ash, and, in dry and semi-dry systems, also the reaction products from the flue gas cleaning process. APC residue is considered a hazardous waste due to its high alkalinity, high content of salts...

  17. Development of a multi-residue method for the determination of pesticides in cereals and dry animal feed using gas chromatography-tandem quadrupole mass spectrometry II. Improvement and extension to new analytes.

    Science.gov (United States)

    Walorczyk, Stanisław

    2008-10-24

    This paper describes the extension and re-validation of a previously published multi-residue method to currently 140 pesticides and 4 pesticide degradation products in cereals and feedingstuffs. The pesticides were extracted using buffered QuEChERS ("quick, easy, cheap, rugged, effective and safe") method and then cleaned up using dispersive solid-phase extraction with Bondesil PSA and C18 sorbents, and optionally by a freezing-out clean-up step. The final extracts were analyzed in a single injection gas chromatographic-tandem quadrupole mass spectrometric (GC-MS/MS) acquisition method. A high degree of confidence was achieved by entering two multiple reaction monitoring transitions per compound. In this way, quantification of analytical results and unequivocal identification of pesticide residues in compliance with the recent European Union criteria could be done in a single analysis. Thorough optimization of the GC-MS/MS acquisition conditions and application of an effective clean-up procedure has resulted in a remarkable enhancement of the validation parameters. The linearity of the calibration curves was excellent in matrix-matched standards, and yielded the coefficients of determination (R(2))> or =0.99 for approximately 96% of the target analytes. Average recoveries of the pesticides spiked at 0.01mgkg(-1) into a feed mixture and wheat grain were in the range 70-120% with associated RSD values feed mixtures and other samples such as malt, starch and dry vegetables have been analyzed. A total of 15 different pesticides have been detected, among which pirimiphos methyl (19 cases), deltamethrin (14 cases), tolylfluanid (5 cases), dichlofluanid (5 cases), and tebuconazole (4 cases) were the most frequently encountered ones.

  18. Proposed systematic methodology for analysis of Pb-210 radioactivity in residues produced in Brazilian natural gas pipes; Proposicao de um modelo analitico sistematico da atividade de Pb-210 em residuos gerados em linhas de gas

    Energy Technology Data Exchange (ETDEWEB)

    Ferreira, Aloisio Cordilha

    2003-11-15

    Since the 80's, the potential radiological hazards due to the handling of solid wastes contaminated with Rn-222 long-lived progeny - Pb-210 in special - produced in gas pipes and removed by pig operations have been subject of growing concern abroad our country. Nevertheless, little or no attention has been paid to this matter in the Brazilian plants up to now, being these hazards frequently underestimated or even ignored. The main purpose of this work was to propose a systematic methodology for analysis of Pb-210 radioactivity in black powder samples from some Brazilian plants, through the evaluation of direct Pb-210 gamma spectrometry and Bi-210 beta counting technical viabilities. In both cases, one in five samples of black powder analysed showed relevant activity (above 1Bq/kg) of Pb-210, being these results probably related to particular features of each specific plant (production levels, reservoir geochemical profile, etc.), in such a way that a single pattern is not observed. For the proposed methodology, gamma spectrometry proved to be the most reliable technique, showing a 3.5% standard deviation, and, for a 95% confidence level, overall fitness in the range of Pb-210 concentration of activity presented in the standard sample reference sheet, provided by IAEA for intercomparison purposes. In the Brazilian scene, however, the availability of statistically supported evidences is insufficient to allow the potential radiological hazard due to the management of black powder to be discarded. Thus, further research efforts are recommended in order to detect the eventually critical regions or plants where gas exploration, production and processing practices will require a regular program of radiological surveillance, in the near future. (author)

  19. Residual nilpotence and residual solubility of groups

    International Nuclear Information System (INIS)

    Mikhailov, R V

    2005-01-01

    The properties of the residual nilpotence and the residual solubility of groups are studied. The main objects under investigation are the class of residually nilpotent groups such that each central extension of these groups is also residually nilpotent and the class of residually soluble groups such that each Abelian extension of these groups is residually soluble. Various examples of groups not belonging to these classes are constructed by homological methods and methods of the theory of modules over group rings. Several applications of the theory under consideration are presented and problems concerning the residual nilpotence of one-relator groups are considered.

  20. Cooling of Gas Turbines I - Effects of Addition of Fins to Blade Tips and Rotor, Admission of Cooling Air Through Part of Nozzles, and Change in Thermal Conductivity of Turbine Components

    Science.gov (United States)

    Brown, Byron

    1947-01-01

    An analysis was developed for calculating the radial temperature distribution in a gas turbine with only the temperatures of the gas and the cooling air and the surface heat-transfer coefficient known. This analysis was applied to determine the temperatures of a complete wheel of a conventional single-stage impulse exhaust-gas turbine. The temperatures were first calculated for the case of the turbine operating at design conditions of speed, gas flow, etc. and with only the customary cooling arising from exposure of the outer blade flange and one face of the rotor to the air. Calculations were next made for the case of fins applied to the outer blade flange and the rotor. Finally the effects of using part of the nozzles (from 0 to 40 percent) for supplying cooling air and the effects of varying the metal thermal conductivity from 12 to 260 Btu per hour per foot per degree Farenheit on the wheel temperatures were determined. The gas temperatures at the nozzle box used in the calculations ranged from 1600F to 2000F. The results showed that if more than a few hundred degrees of cooling of turbine blades are required other means than indirect cooling with fins on the rotor and outer blade flange would be necessary. The amount of cooling indicated for the type of finning used could produce some improvement in efficiency and a large increase in durability of the wheel. The results also showed that if a large difference is to exist between the effective temperature of the exhaust gas and that of the blade material, as must be the case with present turbine materials and the high exhaust-gas temperatures desired (2000F and above), two alternatives are suggested: (a) If metal with a thermal conductivity comparable with copper is used, then the blade temperature can be reduced by strong cooling at both the blade tip and root. The center of the blade will be less than 2000F hotter than the ends; (b) With low conductivity materials some method of direct cooling other than

  1. Modeling daily gas exchange of a Douglas-fir forest : comparison of three stomatal conductance models with and without a soil water stress function

    NARCIS (Netherlands)

    Wijk, van M.T.; Dekker, S.C.; Bouten, W.; Bosveld, F.C.; Kohsiek, W.; Kramer, K.; Mohren, G.M.J.

    2000-01-01

    Modeling stomatal conductance is a key element in predicting tree growth and water use at the stand scale. We compared three commonly used models of stomatal conductance, the Jarvis-Loustau, Ball-Berry and Leuning models, for their suitability for incorporating soil water stress into their

  2. Propagation of a spherical shock wave in mixture of non-ideal gas and small solid particles under the influence of gravitational field with conductive and radiative heat fluxes

    Science.gov (United States)

    Nath, G.

    2016-01-01

    Self-similar solutions are obtained for one-dimensional unsteady adiabatic flow behind a spherical shock wave propagating in a dusty gas with conductive and radiative heat fluxes under the influence of a gravitational field. The shock is assumed to be driven out by a moving piston and the dusty gas to be a mixture of non-ideal gas and small solid particles, in which solid particles are uniformly distributed. It is assumed that the equilibrium flow-conditions are maintained and variable energy input is continuously supplied by the piston. The heat conduction is expressed in terms of Fourier's law and the radiation is considered to be of the diffusion type for an optically thick grey gas model. The thermal conductivity K and the absorption coefficient αR are assumed to vary with temperature and density. The medium is assumed to be under the influence of a gravitational field due to central mass ( bar{m} ) at the origin (Roche Model). It is assumed that the gravitational effect of the mixture itself can be neglected compared with the attraction of the central mass. The initial density of the ambient medium is taken to be always constant. The effects of the variation of the gravitational parameter and nonidealness of the gas in the mixture are investigated. Also, the effects of an increase in (i) the mass concentration of solid particles in the mixture and (ii) the ratio of the density of solid particles to the initial density of the gas on the flow variables are investigated. It is shown that due to an increase in the gravitational parameter the compressibility of the medium at any point in the flow-field behind the shock decreases and all other flow variables and the shock strength are increased. Further, it is found that the presence of gravitational field increases the compressibility of the medium, due to which it is compressed and therefore the distance between the piston and the shock surface is reduced. The shock waves in dusty gas under the influence of a

  3. RESIDUES IN CARROTS TREATED WITH LINURON

    DEFF Research Database (Denmark)

    Løkke, Hans

    1974-01-01

    Investigations have been carried out on residues of linuron and its breakdown products in carrots sprayed with Jinuron at 1, 2, or 4 kg a.i./ha, 0, 19, 28, 36 or 60 days after sowing (up to 57 days before harvesting). The extracted residues were separated into three fractions by liquid......,4-dichloroaniline and iodide ion, followed by gas chromatography with electron capture detector. Only 5-13% of the extract-able residues were breakdown products. Most of the detectable residue (87-95%) was identified as linuron. The relative proportions of linuron and breakdown products in carrots at the time...

  4. Trace gas emissions from combustion of peat, crop residue, domestic biofuels, grasses, and other fuels: configuration and Fourier transform infrared (FTIR) component of the fourth Fire Lab at Missoula Experiment (FLAME-4)

    Science.gov (United States)

    Stockwell, C. E.; Yokelson, R. J.; Kreidenweis, S. M.; Robinson, A. L.; DeMott, P. J.; Sullivan, R. C.; Reardon, J.; Ryan, K. C.; Griffith, D. W. T.; Stevens, L.

    2014-09-01

    During the fourth Fire Lab at Missoula Experiment (FLAME-4, October-November 2012) a large variety of regionally and globally significant biomass fuels was burned at the US Forest Service Fire Sciences Laboratory in Missoula, Montana. The particle emissions were characterized by an extensive suite of instrumentation that measured aerosol chemistry, size distribution, optical properties, and cloud-nucleating properties. The trace gas measurements included high-resolution mass spectrometry, one- and two-dimensional gas chromatography, and open-path Fourier transform infrared (OP-FTIR) spectroscopy. This paper summarizes the overall experimental design for FLAME-4 - including the fuel properties, the nature of the burn simulations, and the instrumentation employed - and then focuses on the OP-FTIR results. The OP-FTIR was used to measure the initial emissions of 20 trace gases: CO2, CO, CH4, C2H2, C2H4, C3H6, HCHO, HCOOH, CH3OH, CH3COOH, glycolaldehyde, furan, H2O, NO, NO2, HONO, NH3, HCN, HCl, and SO2. These species include most of the major trace gases emitted by biomass burning, and for several of these compounds, this is the first time their emissions are reported for important fuel types. The main fire types included African grasses, Asian rice straw, cooking fires (open (three-stone), rocket, and gasifier stoves), Indonesian and extratropical peat, temperate and boreal coniferous canopy fuels, US crop residue, shredded tires, and trash. Comparisons of the OP-FTIR emission factors (EFs) and emission ratios (ERs) to field measurements of biomass burning verify that the large body of FLAME-4 results can be used to enhance the understanding of global biomass burning and its representation in atmospheric chemistry models. Crop residue fires are widespread globally and account for the most burned area in the US, but their emissions were previously poorly characterized. Extensive results are presented for burning rice and wheat straw: two major global crop residues

  5. A REVIEW OF ASSESSMENTS CONDUCTED ON BIO-ETHANOL AS A TRANSPORTATION FUEL FROM A NET ENERGY, GREENHOUSE GAS, AND ENVIRONMENTAL LIFE CYCLE PERSPECTIVE

    Science.gov (United States)

    Interest in producing ethanol from bio-mass in an attempt to make transportation ecologically sustainable continues to grow. In recent years, a large number of assessments have been conducted to assess the environmental merit of biofuels. Two detailed reviews that looked at the s...

  6. Forest residues in cattle feed

    Directory of Open Access Journals (Sweden)

    João Elzeário Castelo Branco Iapichini

    2012-12-01

    Full Text Available The ruminants are capable of converting low-quality food, when they are complementes with high-energy source. Through the use of regional agricultural residues is possible to conduct more economical production systems, since energetic foods have high cost in animal production. There is very abundant availability of residues in agroforestry activities worldwide, so that if a small fraction of them were used with appropriate technical criteria they could largely meet the needs of existing herds in the world and thus meet the demands of consumption of protein of animal origin. The Southwest Region of São Paulo State has large area occupied by reforestation and wide availability of non-timber forest residues, which may represent more concentrated energetic food for ruminant production. This experiment aimed to evaluate the acceptability of ground pine (20, 30 and 40%, replacing part of the energetic food (corn, present in the composition of the concentrate and was performed at the Experimental Station of Itapetininga - Forest Institute / SMA, in the dry season of 2011. It were used four crossbred steers, mean 18 months old, average body weight of 250 kg, housed in a paddock provided with water ad libitum and covered troughs for supplementation with the experimental diet. The adjustment period of the animals was of 07 days and the measurement of the levels of consumption, physiological changes, acceptability and physiological parameters were observed during the following 25 days. The concentrate supplement was formulated based on corn (76.2%, Soybean Meal (20%, urea (2%, Ammonium sulfate (0.4%, calcite (1.4%, Mineral Core (1% and finely ground Pine Cone, replacing corn. In preparing food, the formulas were prepared to make them isoproteic/energetic, containing the following nutrient levels: 22% Crude Protein (CP and 79% of Total Nutrients (TDN. The animals received the supplement in three steps for each level of cone replaced, being offered in the

  7. Asymptotic behavior of the motion of a viscous heat-conducting one-dimesional gas with radiation: the pure scattering case

    Czech Academy of Sciences Publication Activity Database

    Ducomet, B.; Nečasová, Šárka

    2013-01-01

    Roč. 11, č. 1 (2013), s. 1350003 ISSN 0219-5305 R&D Projects: GA ČR GA201/08/0012 Institutional research plan: CEZ:AV0Z10190503 Keywords : compressible fluids * viscous * conducting fluids Subject RIV: BA - General Mathematics Impact factor: 1.500, year: 2013 http://www.worldscientific.com/doi/abs/10.1142/S0219530513500036

  8. Residual Ash Formation during Suspension-Firing of Biomass

    DEFF Research Database (Denmark)

    Damø, Anne Juul; Jappe Frandsen, Flemming; Jensen, Peter Arendt

    2014-01-01

    Through 50+ years, high quality research has been conducted in order to characterize ash and deposit formation in utility boilers fired with coal, biomass and waste fractions. The basic mechanism of fly ash formation in suspension fired coal boilers is well described, documented and may even....... The objective of this work was to generate novel and comprehensive data on the formation of residual fly ash during the initial stage (0.25 – 2.0 s) of suspension-firing of biomass (pulverized wood and straw). Combustion experiments were carried out with bio-dust (pulverized straw and wood), in an entrained...... flow reactor, simulating full-scale suspension-firing of biomass. By the use of a movable, cooled and quenched gas/ particle sampling probe, samples were collected at different positions along the vertical axis in the reactor, corresponding to gas residence times, varying in the range [0.25 – 2.0 s...

  9. Determination of Physical Properties of Carbon Materials by Results of Ablative Experiments Con-ducted in the Jets of Gas Dynamic Units

    Directory of Open Access Journals (Sweden)

    V. V. Gorsky

    2015-01-01

    Full Text Available The process of hypersonic vehicles’ movement in the dense layers of the atmosphere is accompanied by the considerable combustion of heat shield, which effects on the aerodynamic, mass-inertial and centering characteristics of the product.For correct calculation of model's movement parameters it is necessary:* Using the theoretical and computation methods for determining ablative characteristics of heat-protective materials;* Taking into account all the basic physical and chemical processes, involved in their ablation, using the above mentioned methods;* Testing these techniques in the wide range of experimental data. This physic-mathematical model of carbon materials (CM aerothermochemical destruction is based on using the following:* Arrhenius equations to calculate carbon kinetic oxidation;* Langmuir-Knudsen formula to calculate the velocity of non-equilibrium carbon’s sublimation;* Carbon erosion law represented as a unique dependence of this process velocity on the gas pressure on the wall.Mathematical description of all major processes included in this formulation of the problem, contains a number of "free" parameters that can be determined only on the basis of comparison of theoretical and experimental data according to total ablation characteristics of these materials.This comparison was performed in the article applicable to the tests conditions of modern CM in the stream of electric arc plant and in combustion products of liquid-propellant rocket engines.As the result, the data of kinetic of carbon oxidation by atomic oxygen at sublimation mode of material ablation were obtained for the first time. Carbon erosion law under high pressure was established for the first time.The new approach to processing of ablation experiments is enunciated. Using this approach allows to turn this experiments for CM from comparative tests into the tests to determine ablation properties of thermal protection. Moreover, it enables us also to use the

  10. Gas exchange and nutrient content in leaves of physic nut irrigated with wastewater and doses of phosphorusTrocas gasosas e teor de nutrientes em folhas de pinhão manso irrigado com água residuária e doses de fósforo

    Directory of Open Access Journals (Sweden)

    Elka Costa Santos Nascimento

    2012-10-01

    Full Text Available With the objective of evaluating leaf gas exchange and nutrient concentration in plants of Physic nut irrigated with wastewater of domestic origin an experiment was conducted in protected ambient adopting randomized block in factorial layout, to study the effects of five levels of hydric reposition – HR (0.25; 0.50; 0.75; 1.00 and 1.25 times of water consumed by the plant, and two levels of phosphorus (135 and 200 g P2O5 plant-1 year-1 with four repetitions. The data of leaf gas exchange were obtained using a portable photosynthesis meter (IRGA. To determine the nutrient content of the plant, fourth and fifth leaves below the inflorescence was used. The reduction in water supply provoked reduction in the rate of carbon assimilation, limiting the production capacity of the Physic nut plants. The increase in level of hydric reposition with wastewater resulted increase in leaf gas exchange, notably in the rate of carbon assimilation. The accumulation of the nutrient follows the sequence: N > K > Ca > Na > Cl > Mg > P > S > Fe > Mn > Zn > Cu, and with the increase of water supply the leaf contents of phosphorus, zinc and copper increased. The doses of P2O5 did not influence the contents of studied elements.Com o objetivo de avaliar trocas gasosas e teores de minerais em plantas de pinhão manso irrigadas com água residuária de origem doméstica foi conduzido um ensaio em ambiente protegido adotando-se um delineamento em blocos casualizados em um fatorial com cinco níveis de reposição hídrica (0,25; 0,50; 0,75; 1,00 e 1,25 do consumo de água pela planta e duas doses de P2O5 (135 e 200 g planta-1 por ano com quatro repetições. Os dados de trocas gasosas foliares foram obtidos utilizando-se medidor portátil de fotossíntese (IRGA. Para determinar o teor de nutrientes da planta, utilizou-se o limbo foliar localizado entre a quarta e quinta folha abaixo da inflorescência. A redução da reposição hídrica provocou diminuição na taxa de

  11. What drives natural gas prices?

    OpenAIRE

    Brown, Stephen P. A.; Yücel, Mine K.

    2007-01-01

    For many years, fuel switching between natural gas and residual fuel oil kept natural gas prices closely aligned with those for crude oil. More recently, however, the number of U.S. facilities able to switch between natural gas and residual fuel oil has declined, and over the past five years, U.S. natural gas prices have been on an upward trend with crude oil prices but with considerable independent movement. Natural gas market analysts generally emphasize weather and inventories as drivers o...

  12. Ex-reactor determination of thermal gap and contact conductance between uranium dioxide: zircaloy-4 interfaces. Stage I: low gas pressure

    International Nuclear Information System (INIS)

    Garnier, J.E.; Begej, S.

    1979-04-01

    A study of thermal gap and contact conductance between depleted uranium dioxide (UO 2 ) and Zircaloy-4 (Zr4) has been made utilizing two measurement apparatuses developed as part of this program. The Modified Pulse Design (MPD) apparatus is a transient technique employing a heat pulse (laser) and a signal detector to monitor the thermal energy transmitted through a UO 2 /Zr4 sample pair which are either physically separated or in contact. The Modified Longitudinal Design (MLD) apparatus is a steady-state technique based on a modified cylindrical column design with a self-guarding sample geometry. Description of the MPD and MLD apparatus, data acquisition, reduction and error analysis is presented along with information on specimen preparation, thermal property and surface characterization. A technique using an optical height gauge to determine the average mean-plane of separation between the simple pairs is also presented

  13. Residual stress measurement at Budapest Neutron Center

    International Nuclear Information System (INIS)

    Gyula, T.

    2005-01-01

    The use of residual stress measurements of different construction element and recent possibilities of Budapest Neutron Centre are presented. The details investigated already: gas turbine wheel, axial compressor blade, turbine blade and plastically deformed stainless steel. We demonstrated the use of a neutron scattering (SANS, residual stress, diffraction) for the materials behavior investigation in order to analyze the processes going on under the different mechanical loading. The direction of possible instrumental development is presented. (author)

  14. Residue studies of Methabenzthiazuron in Soil, Lentils and Hay

    International Nuclear Information System (INIS)

    Al-Maghrabi, K.I.

    2002-01-01

    Over two years, replicate plots of lentils (Lens culinaris L.) were treated before seeding with methabenzthiazuron at a rate of 0.5 kg a.i. ha-1. In each year representative soil, lentil and hay samples were randomly collected from plots of each treatment. Soil samples were tested for residues 24 hours after treatment and harvest. Lentil and hay samples were tested at harvest. A cleanup step was conducted after extraction. Gas chromatograph equipped with a nitrogen/phosphorus detector was used to detect methabenzthiazuron. Overall average of residue levels in soil decreased significantly from 1.16+-0.15 mg kg, 24 hours after treatment, 0.12 +-0.01 mg kg at harvest. No significant difference in the maximum average residue was found in lentil and hay samples collected from various plots and tested at harvest (0.10+-0.01 and 0.19 +-0.02 mg kg in lentils and hay, respectively). Recovery tests were conducted with each group of samples tested in order to determine the efficiency of analytical procedure. (author)

  15. Multi-class, multi-residue analysis of pesticides, polychlorinated biphenyls, polycyclic aromatic hydrocarbons, polybrominated diphenyl ethers and novel flame retardants in fish using fast, low-pressure gas chromatography-tandem mass spectrometry

    Energy Technology Data Exchange (ETDEWEB)

    Sapozhnikova, Yelena, E-mail: yelena.sapozhnikova@ars.usda.gov [US Department of Agriculture, Agricultural Research Service, Eastern Regional Research Center, 600 East Mermaid Lane, Wyndmoor, PA 193038 (United States); Lehotay, Steven J. [US Department of Agriculture, Agricultural Research Service, Eastern Regional Research Center, 600 East Mermaid Lane, Wyndmoor, PA 193038 (United States)

    2013-01-03

    Highlights: Black-Right-Pointing-Pointer A method for analysis of POPs and novel flame retardants in catfish was developed. Black-Right-Pointing-Pointer The method is based on a QuEChERS extraction, d-SPE clean-up and low pressure GC/MS-MS. Black-Right-Pointing-Pointer The method validation demonstrated good recoveries and low detection limits. Black-Right-Pointing-Pointer The method was successfully applied for analysis of catfish samples from the market. - Abstract: A multi-class, multi-residue method for the analysis of 13 novel flame retardants, 18 representative pesticides, 14 polychlorinated biphenyl (PCB) congeners, 16 polycyclic aromatic hydrocarbons (PAHs), and 7 polybrominated diphenyl ether (PBDE) congeners in catfish muscle was developed and evaluated using fast low pressure gas chromatography triple quadrupole tandem mass spectrometry (LP-GC/MS-MS). The method was based on a QuEChERS (quick, easy, cheap, effective, rugged, safe) extraction with acetonitrile and dispersive solid-phase extraction (d-SPE) clean-up with zirconium-based sorbent prior to LP-GC/MS-MS analysis. The developed method was evaluated at 4 spiking levels and further validated by analysis of NIST Standard Reference Materials (SRMs) 1974B and 1947. Sample preparation for a batch of 10 homogenized samples took about 1 h/analyst, and LP-GC/MS-MS analysis provided fast separation of multiple analytes within 9 min achieving high throughput. With the use of isotopically labeled internal standards, recoveries of all but one analyte were between 70 and 120% with relative standard deviations less than 20% (n = 5). The measured values for both SRMs agreed with certified/reference values (72-119% accuracy) for the majority of analytes. The detection limits were 0.1-0.5 ng g{sup -1} for PCBs, 0.5-10 ng g{sup -1} for PBDEs, 0.5-5 ng g{sup -1} for select pesticides and PAHs and 1-10 ng g{sup -1} for flame retardants. The developed method was successfully applied for analysis of catfish samples

  16. Lunar soil properties and soil mechanics. Flow in porous media under rarefied gas conditions. Research phase: Fluid conductivity of lunar surface materials

    Science.gov (United States)

    Hurlbut, F. C.; Jih, C. R.

    1972-01-01

    Theoretical and experimental research on fluid conductivity of lunar surface materials is summarized. Theoretical methods were developed for the analysis of transitional and free-molecular flows, and for analysis of lunar permeability probe data in general. Experimental studies of rarefied flows under conditions of a large pressure gradient show flows in the continuum regime to be responsible for the largest portion of the pressure drop between source and sink for one dimensional flow, provided the entrance Knudsen number is sufficiently small. The concept of local similarity leading to a universal nondimensional function of Knudsen number was shown to have approximate validity; flows in all regimes may be described in terms of an area fraction and a single length parameter. Synthetic porous media prepared from glass beads exhibited flow behavior similar in many regards to that of a natural sandstone; studies using artificial stones with known pore configurations may lead to new insight concerning the structure of natural materials. The experimental method involving the use of segmented specimens of large permeability is shown to be fruitful.

  17. Does Bt Corn Really Produce Tougher Residues

    Science.gov (United States)

    Bt corn hybrids produce insecticidal proteins that are derived from a bacterium, Bacillus thuringiensis. There have been concerns that Bt corn hybrids produce residues that are relatively resistant to decomposition. We conducted four experiments that examined the decomposition of corn residues und...

  18. Gas and Gas Pains

    Science.gov (United States)

    ... to produce gas. Often, relatively simple changes in eating habits can lessen bothersome gas. Certain digestive system disorders, ... such as soda and beer, increase stomach gas. Eating habits, such as eating too quickly, drinking through a ...

  19. Conduct disorder

    Science.gov (United States)

    ... this page: //medlineplus.gov/ency/article/000919.htm Conduct disorder To use the sharing features on this page, please enable JavaScript. Conduct disorder is a set of ongoing emotional and behavioral ...

  20. Conducting Polymers

    Indian Academy of Sciences (India)

    would exhibit electronic conductivity, their conductivities (of compressed pellets) were indeed measured by others, and were found to be .... Polyaniline. Polyphenylene. Polypheny lene- vinylene. Table 1. G!NeRAl I ARTICl! structure. Maximum conductivity Stem Stability. Processability. ~. 1.5 x 105. Reacts with Film not n air.

  1. Thermal conductivity of the Lennard-Jones chain fluid model.

    Science.gov (United States)

    Galliero, Guillaume; Boned, Christian

    2009-12-01

    Nonequilibrium molecular dynamics simulations have been performed to estimate, analyze, and correlate the thermal conductivity of a fluid composed of short Lennard-Jones chains (up to 16 segments) over a large range of thermodynamic conditions. It is shown that the dilute gas contribution to the thermal conductivity decreases when the chain length increases for a given temperature. In dense states, simulation results indicate that the residual thermal conductivity of the monomer increases strongly with density, but is weakly dependent on the temperature. Compared to the monomer value, it has been noted that the residual thermal conductivity of the chain was slightly decreasing with its length. Using these results, an empirical relation, including a contribution due to the critical enhancement, is proposed to provide an accurate estimation of the thermal conductivity of the Lennard-Jones chain fluid model (up to 16 segments) over the domain 0.8values of the Lennard-Jones chain fluid model merge on the same "universal" curve when plotted as a function of the excess entropy. Furthermore, it is shown that the reduced configurational thermal conductivity of the Lennard-Jones chain fluid model is approximately proportional to the reduced excess entropy for all fluid states and all chain lengths.

  2. The grapevine root-specific aquaporin VvPIP2;4N controls root hydraulic conductance and leaf gas exchange under well-watered conditions but not under water stress.

    Science.gov (United States)

    Perrone, Irene; Gambino, Giorgio; Chitarra, Walter; Vitali, Marco; Pagliarani, Chiara; Riccomagno, Nadia; Balestrini, Raffaella; Kaldenhoff, Ralf; Uehlein, Norbert; Gribaudo, Ivana; Schubert, Andrea; Lovisolo, Claudio

    2012-10-01

    We functionally characterized the grape (Vitis vinifera) VvPIP2;4N (for Plasma membrane Intrinsic Protein) aquaporin gene. Expression of VvPIP2;4N in Xenopus laevis oocytes increased their swelling rate 54-fold. Northern blot and quantitative reverse transcription-polymerase chain reaction analyses showed that VvPIP2;4N is the most expressed PIP2 gene in root. In situ hybridization confirmed root localization in the cortical parenchyma and close to the endodermis. We then constitutively overexpressed VvPIP2;4N in grape 'Brachetto', and in the resulting transgenic plants we analyzed (1) the expression of endogenous and transgenic VvPIP2;4N and of four other aquaporins, (2) whole-plant, root, and leaf ecophysiological parameters, and (3) leaf abscisic acid content. Expression of transgenic VvPIP2;4N inhibited neither the expression of the endogenous gene nor that of other PIP aquaporins in both root and leaf. Under well-watered conditions, transgenic plants showed higher stomatal conductance, gas exchange, and shoot growth. The expression level of VvPIP2;4N (endogenous + transgene) was inversely correlated to root hydraulic resistance. The leaf component of total plant hydraulic resistance was low and unaffected by overexpression of VvPIP2;4N. Upon water stress, the overexpression of VvPIP2;4N induced a surge in leaf abscisic acid content and a decrease in stomatal conductance and leaf gas exchange. Our results show that aquaporin-mediated modifications of root hydraulics play a substantial role in the regulation of water flow in well-watered grapevine plants, while they have a minor role upon drought, probably because other signals, such as abscisic acid, take over the control of water flow.

  3. Conduct Disorder

    Science.gov (United States)

    ... do not receive early and comprehensive treatment . Without treatment, many youngsters with conduct disorder are unable to adapt to the demands of ... break laws or behave in an antisocial manner. Treatment of children with conduct disorder can be complex and challenging. Treatment can be ...

  4. Residual stress characterization of steel TIG welds by neutron diffraction and by residual magnetic stray field mappings

    Science.gov (United States)

    Stegemann, Robert; Cabeza, Sandra; Lyamkin, Viktor; Bruno, Giovanni; Pittner, Andreas; Wimpory, Robert; Boin, Mirko; Kreutzbruck, Marc

    2017-03-01

    The residual stress distribution of tungsten inert gas welded S235JRC+C plates was determined by means of neutron diffraction (ND). Large longitudinal residual stresses with maxima around 600 MPa were found. With these results as reference, the evaluation of residual stress with high spatial resolution GMR (giant magneto resistance) sensors was discussed. The experiments performed indicate a correlation between changes in residual stresses (ND) and the normal component of local residual magnetic stray fields (GMR). Spatial variations in the magnetic field strength perpendicular to the welds are in the order of the magnetic field of the earth.

  5. DDT residues in sediments from the Bay of Bengal

    Digital Repository Service at National Institute of Oceanography (India)

    Sarkar, A.; SenGupta, R.

    in the sediments from the Bay of Bengal. Peterson grab and hydrographic winch was used to collect the sediment samples. Each sample was extracted and cleaned. Residues were detected by electron capture gas chromatography. A range variation in the concentration...

  6. Technical and economical analysis of the energy recovery during in incineration of urban solid residues; Analise tecnico-economica da recuperacao de energia durante a incineracao de residuos solidos urbanos

    Energy Technology Data Exchange (ETDEWEB)

    Teixeira, Flavio N.; Lora, Electo S.; Martins, Andre R.S. [Escola Federal de Engenharia de Itajuba, MG (Brazil). Dept. de Mecanica

    1999-07-01

    This work conducts a technical and economical evaluation on the energetic recovering of an incinerator with processing capacity of 600 t/h of urban solid residues, resulting from electric power generation (gas turbines) and cooling (absorption systems) using garbage and natural gas. The results allow the conclusion that besides the social and environmental benefits resulting from the elimination of the contamination potential, an electric energy surplus can be generated for inclusion in the Brazilian energy matrix.

  7. Natural gas; Gas Natural

    Energy Technology Data Exchange (ETDEWEB)

    Lopes, Carlos A.; Moraes, Claudia C.D. [Eletricidade de Sao Paulo S.A. (ELETROPAULO), Sao Paulo, SP (Brazil); Fonseca, Carlos H.F. [Centrais Eletricas de Santa Catarina S.A., Florianopolis, SC (Brazil); Silva, Clecio Fabricio da; Alves, Ricardo P. [Companhia Paranaense de Energia (COPEL), Curitiba, PR (Brazil); Sposito, Edivaldo Soares; Hulle, Lutero [Espirito Santo Centrais Eletricas S.A. (ESCELSA), Vitoria, ES (Brazil); S. Martins, Icaro da [Centrais Eletricas do Norte do Brasil S.A. (ELETRONORTE), Belem, PA (Brazil); Vilhena, Joao Luiz S. de [Companhia Energetica de Minas Gerais (CEMIG), Belo Horizonte, MG (Brazil); Fagundes, Zaluar Aquino [Companhia Estadual de Energia Eletrica do Estado do Rio Grande do Sul, Porto Alegre, RS (Brazil)

    1996-12-31

    An increase in the consumption of natural gas in Brazil is an expected fact in what concerns energetic planning. This work presents the existing situation in what concerns natural gas utilization in the main world economies, as well as an analysis of the participation of this fuel among the energy final consumption per sources. The Brazilian consumption of natural gas is also analysed as well as the international agreement between Brazil and Bolivia for natural gas commercialization. Some legal, institutional and political aspects related to natural gas commercialization are also discussed. Finally, several benefits to be brought by the utilization of natural gas are presented 10 refs., 3 tabs.

  8. Functional residual capacity measurement by heptafluoropropane in ventilated newborn lungs

    OpenAIRE

    Kusztrich, Ariane

    2012-01-01

    Objective: Heptafluoropropane is an inert gas commercially used as propellant for inhalers. Since heptafluoropropane can be detected in low concentrations, it could also be used as a tracer gas to measure functional residual capacity. The aim of the present study was to validate functional residual capacity measurements by heptafluoropropane wash-in/wash-out (0.8%) during mechanical ventilation in small, surfactant-depleted lungs using a newborn piglet model. Design: Prospective laborato...

  9. Electrical Conductivity.

    Science.gov (United States)

    Hershey, David R.; Sand, Susan

    1993-01-01

    Explains how electrical conductivity (EC) can be used to measure ion concentration in solutions. Describes instrumentation for the measurement, temperature dependence and EC, and the EC of common substances. (PR)

  10. Thermal Conductivity of Foam Glass

    DEFF Research Database (Denmark)

    Petersen, Rasmus Rosenlund; König, Jakob; Yue, Yuanzheng

    as thermal insulating material in building and chemical industry. The large volume of gas (porosity 90 – 95%) is the main reason of the low thermal conductivity of the foam glass. If gases with lower thermal conductivity compared to air are entrapped in the glass melt, the derived foam glass will contain...... only closed pores and its overall thermal conductivity will be much lower than that of the foam glass with open pores. In this work we have prepared foam glass using different types of recycled glasses and different kinds of foaming agents. This enabled the formation of foam glasses having gas cells...... with different gas compositions. The foam glasses were characterised concerning densities, open/closed porosity and crystallinity. We find out, through analytical calculations and experiments, how the thermal conductivity of foam glass depends on density, glass composition and gas composition. Certain glass...

  11. pH and electric conductivity study of H{sub 2}O/MEG/salt systems on monoethyleneglycol (MEG) reclamation units in gas processing; Estudo de pH e condutividade eletrica em sistemas H{sub 2}O/MEG/sal, em unidades de recuperacao de monoetilenoglicol (MEG), no processamento de gas natural

    Energy Technology Data Exchange (ETDEWEB)

    Senna, Camila; Carrijo, Darley; Nascimento, Jailton; Grava, Wilson [PETROBRAS, Rio de Janeiro, RJ (Brazil). Centro de Pesquisas (CENPES); Lemos, Alessandro A.; Andrade, Wander V.; Chiavone-Filho, Osvaldo; Amorim, Josinira Antunes de [Universidade Federal do Rio Grande do Norte (UFRN), Natal, RN (Brazil). Dept. de Engenharia Quimica

    2008-07-01

    The monoethylene glycol (MEG) is injected in natural gas production wells in order to combine with the free water, altering the thermodynamic conditions for the formation of hydrates. The presence of MEG in aqueous solutions containing salts provokes the decrease of the solubility of the same ones. Information of properties as the pH and the conductivity are important for the control of the process. Before this, the present work has as objective determines the behavior of the aqueous solutions with MEG and NaCl in pH and conductivity terms, in different temperatures, with views to the stage of recovery of MEG and the salt precipitation beginning. The experimental methodology consisted of the elaboration of synthetic solutions of the mixtures in study, covering every MEG concentration range and temperature between 5 and 90 deg C. The conductivity results for the system H{sub 2}O+MEG showed that the conductivity decreases with the concentration of MEG and it increases with the temperature. A conductivity increase was observed for diluted concentrations of MEG, due to the most pronounced effect of protonation of MEG. For pH measures, it was necessary to develop a calibration procedure due to the fact that this property varies with the solvent media. The pH values decrease as it increases the concentration of MEG, reaching a value practically constant around 40%. (author)

  12. Assessment of Pesticide Residue Levels in Vegetables sold in some ...

    African Journals Online (AJOL)

    This study investigated pesticide residue levels in the two vegetables commonly eaten in Lagos state Nigeria. The vegetables (Telfairia occidentalis and Celosia argentea) were purchased from six markets (Oyingbo, Mile 12, Mushin, Ajah, Agege and Festac) in Lagos. The pesticide residue levels were determined using gas ...

  13. Gas and Gas Pains

    Science.gov (United States)

    ... Gas and gas pains Symptoms & causes Diagnosis & treatment Advertisement Mayo Clinic does not endorse companies or products. ... a Job Site Map About This Site Twitter Facebook Google YouTube Pinterest Mayo Clinic is a not- ...

  14. Residual stress measurement for injection molded components

    Directory of Open Access Journals (Sweden)

    Achyut Adhikari

    2016-07-01

    Full Text Available Residual stress induced during manufacturing of injection molded components such as polymethyl methacrylate (PMMA affects the mechanical and optical properties of these components. These residual stresses can be visualized and quantified by measuring their birefringence. In this paper, a low birefringence polariscope (LBP is used to measure the whole-field residual stress distribution of these injection molded specimens. Detailed analytical and experimental study is conducted to quantify the residual stress measurement in these materials. A commercial birefringence measurement system was used to validate the results obtained to our measurement system. This study can help in material diagnosis for quality and manufacturing purpose and be useful for understanding of residual stress in imaging or other applications.

  15. Emissions of volatile organic compounds from maize residue open burning in the northern region of Thailand

    Science.gov (United States)

    Sirithian, Duanpen; Thepanondh, Sarawut; Sattler, Melanie L.; Laowagul, Wanna

    2018-03-01

    Emission factors for speciated volatile organic compounds (VOCs) from maize residue burning were determined in this study based on chamber experiments. Thirty-six VOC species were identified by Gas Chromatography/Mass Spectrometer (GC/MS). They were classified into six groups, including alkanes, alkenes, oxygenated VOCs, halogenated VOCs, aromatics and other. The emission factor for total VOCs was estimated as about 148 mg kg-1 dry mass burned. About 68.4% of the compounds were aromatics. Field samplings of maize residues were conducted to acquire the information of fuel characteristics including fuel loading, fraction of maize residues that were actually burned as well as proximate and elemental analysis of maize residues. The emission factors were then applied to estimate speciated VOC emissions from maize residue open burning at the provincial level in the upper-northern region of Thailand for the year 2014. Total burned area of maize covered an area of about 500,000 ha which was about 4.7% of the total area of upper-northern region of the country. It was found that total VOC emissions released during the burning season (January-April) was about 79.4 tons. Ethylbenzene, m,p-xylene, 1,2,4-trimethylbenzene, acetaldehyde and o-xylene were the major contributors, accounting for more than 65% of total speciated VOC emissions.

  16. Conducting Polymers

    Indian Academy of Sciences (India)

    backbone (by the process of doping) and make them electrically. Conducting Polymers. From a Laboratory Curiosity to the Market Place. S Ramakrishnan ..... switching occurs between transparent yellow and green in less than. 100ms. Thus, while these materials are yet to achieve the set target. (in terms of their life cycle) ...

  17. Conducting Polymers

    Indian Academy of Sciences (India)

    Home; Journals; Resonance – Journal of Science Education; Volume 16; Issue 12. Conducting Polymers - From a Laboratory Curiosity to the Market Place. S Ramakrishnan. Volume 16 Issue 12 December 2011 pp 1254-1265. Fulltext. Click here to view fulltext PDF. Permanent link:

  18. Conduct disorders

    NARCIS (Netherlands)

    Buitelaar, J.K.; Smeets, K.C.; Herpers, P.; Scheepers, F.; Glennon, J.; Rommelse, N.N.J.

    2013-01-01

    Conduct disorder (CD) is a frequently occurring psychiatric disorder characterized by a persistent pattern of aggressive and non-aggressive rule breaking antisocial behaviours that lead to considerable burden for the patients themselves, their family and society. This review paper updates diagnostic

  19. Pesticide residues in locally available cereals and vegetables

    International Nuclear Information System (INIS)

    Cunanan, S.A.; Santos, F.L.; Bonoan, L.S.

    1976-03-01

    Vegetable samples (pechay, cabbage, lettuce, green beans and tomatoes) bought from public markets in the Metro Manila area were analyzed for pesticide residues using gas chromatography. The samples analyzed in 1968-69 contained high levels of chlorinated pesticides such as DDT, Aldrin, Endrin, and Thiodan, while in the samples analyzed in January 1976, no chlorinated and organophosphate pesticides were detected. Cereal samples (rice, corn and sorghum) were obtained from the National Grains Authority and analyzed for pesticide residues and bromine residues. Total bromine residues was determined by neutron activation analysis. In most of the samples analyzed, the concentrations of pesticide residues were below the tolerance levels set by the FAO/WHO Committee on Pesticide Residues in Foods. An exception was one rice sample from Thailand, the bromine residue content (110ppm) of which exceeds the tolerance level of 50ppm

  20. Recycling of automobile shredder residue with a microwave pyrolysis combined with high temperature steam gasification

    International Nuclear Information System (INIS)

    Donaj, Pawel; Yang, Weihong; Blasiak, Wlodzimierz; Forsgren, Christer

    2010-01-01

    Presently, there is a growing need for handling automobile shredder residues - ASR or 'car fluff'. One of the most promising methods of treatment ASR is pyrolysis. Apart of obvious benefits of pyrolysis: energy and metals recovery, there is serious concern about the residues generated from that process needing to be recycled. Unfortunately, not much work has been reported providing a solution for treatment the wastes after pyrolysis. This work proposes a new system based on a two-staged process. The ASR was primarily treated by microwave pyrolysis and later the liquid and solid products become the feedstock for the high temperature gasification process. The system development is supported within experimental results conducted in a lab-scale, batch-type reactor at the Royal Institute of Technology (KTH). The heating rate, mass loss, gas composition, LHV and gas yield of producer gas vs. residence time are reported for the steam temperature of 1173 K. The sample input was 10 g and the steam flow rate was 0.65 kg/h. The conversion reached 99% for liquids and 45-55% for solids, dependently from the fraction. The H 2 :CO mol/mol ratio varied from 1.72 solids and 1.4 for liquid, respectively. The average LHV of generated gas was 15.8 MJ/N m 3 for liquids and 15 MJ/N m 3 for solids fuels.

  1. Agricultural pesticide residues

    International Nuclear Information System (INIS)

    Fuehr, F.

    1984-01-01

    The utilization of tracer techniques in the study of agricultural pesticide residues is reviewed under the following headings: lysimeter experiments, micro-ecosystems, translocation in soil, degradation of pesticides in soil, biological availability of soil-applied substances, bound residues in the soil, use of macro- and microautography, double and triple labelling, use of tracer labelling in animal experiments. (U.K.)

  2. Determinação de resíduos de pesticidas em plasma bovino por cromatografia gasosa-espectrometria de massas Pesticides residue determination in cattle plasma by gas chromatography-mass spectrometry

    OpenAIRE

    Daniele Fernanda Maffei; Ana Rita de Araújo Nogueira; Silvia Helena Govoni Brondi

    2009-01-01

    An analytical method for the isolation based on matrix solid-phase dispersion technique and gas chromatographic determination of pesticides in cattle plasma is presented. It was fortified 0.25 g of plasma with pesticides and blended with 1 g each C18 and Na2SO4. The homogenized matter was transferred to a SPE cartridge, which contained 1 g of activated florisil with 5 mL acetonitrile. The analites were eluted under vaccum with 15 mL acetonitrile, the extract was analyzed by gas chromatography...

  3. 30 CFR 202.151 - Royalty on processed gas.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Royalty on processed gas. 202.151 Section 202... MANAGEMENT ROYALTIES Federal Gas § 202.151 Royalty on processed gas. (a)(1) A royalty, as provided in the... settlement without resorting to processing; and (ii) Residue gas and all gas plant products resulting from...

  4. Study on production mechanism of welding residual stress at the juncture of a pipe penetrating a thick plate

    International Nuclear Information System (INIS)

    Mochizuki, Masahito; Enomoto, Kunio; Okamoto, Noriaki; Saitoh, Hideyo; Hayashi, Eisaku.

    1994-01-01

    This paper studies welding residual stresses at the intersection of a small diameter pipe penetrating a thick plate. The pipe is welded to the plate, and Tungsten Innert Gas (TIG) cladding is melted on the inner surface of the pipe to protect it from stress corrosion cracking due to long operation in nuclear power plants. Stresses are calculated by heat conduction analysis and thermal elasto-plastic analysis, and also measured by strain gauges. Welding residual stresses are shown to have no corrosive influence on the inner pipe surface, and the stresses are compressed enough to protect the pipe against stress corrosion cracking on the outer surface. It was also studied to make clear the production mechanism of the residual stresses which were generated by welding processes at the pipe. (author)

  5. Gas-on-gas competition in Shanghai

    International Nuclear Information System (INIS)

    Manuhutu, Chassty; Owen, Anthony D.

    2010-01-01

    In common with other major economic centres in China, Shanghai's energy consumption has been increasing rapidly to support the high growth rate of its economy. To achieve rational, efficient and clean use of energy, together with improved environmental quality within the city, the Shanghai municipal government has decided to expand the supply and utilization of natural gas. Shanghai plans to increase the share of natural gas in its primary energy mix to 7 per cent by 2010, up from 3 per cent in 2005. This increase in natural gas demand has to be matched with a corresponding increase in supply. To date, the Shanghai region has relied on offshore extracted natural gas but this supply is limited due to the size of the reserves. Since 2005, the West-East pipeline has provided an alternative for Shanghai but demands from other regions could reduce the potential for expanding supplies from that source. Since domestic production will not be sufficient to meet demand in the near future, Shanghai is building a liquefied natural gas (LNG) regasification terminal at the Yangshan deep-water port that would allow an additional supply of more than 3 billion cubic meters per year of natural gas. Malaysia has already committed to supply LNG to the Shanghai terminal at a price that is significantly higher than the wholesale 'city-gate' price for natural gas transported via pipeline, but still lower than the gas price to end-use consumers. The presence of both an LNG terminal and a transmission pipeline that connects Shanghai to domestic gas-producing regions will create gas-on-gas competition. This study assesses the benefits of introducing such competition to one of China's most advanced cities under various scenarios for demand growth. In this paper, the impact of imported LNG on market concentration in Shanghai's gas market will be analysed using the Herfindahl-Hirschmann index (HHI) and the residual supply index (RSI). Our results show that Shanghai remains a supply

  6. Conductivity Probe

    Science.gov (United States)

    2008-01-01

    The Thermal and Electrical Conductivity Probe (TECP) for NASA's Phoenix Mars Lander took measurements in Martian soil and in the air. The needles on the end of the instrument were inserted into the Martian soil, allowing TECP to measure the propagation of both thermal and electrical energy. TECP also measured the humidity in the surrounding air. The needles on the probe are 15 millimeters (0.6 inch) long. The Phoenix Mission is led by the University of Arizona, Tucson, on behalf of NASA. Project management of the mission is by NASA's Jet Propulsion Laboratory, Pasadena, Calif. Spacecraft development is by Lockheed Martin Space Systems, Denver.

  7. Improvement and extension to new analytes of a multi-residue method for the determination of pesticides in cereals and dry animal feed using gas chromatography-tandem quadrupole mass spectrometry revisited.

    Science.gov (United States)

    Walorczyk, Stanisław; Drożdżyński, Dariusz

    2012-08-17

    This article describes a substantially improved multi-residue method for the determination of a large number of pesticides in cereal samples (wheat, rye, barley, oats, maze, buckwheat etc.) and various animal feeds. The sample preparation method and the GC-MS/MS acquisition method were modified to accommodate new complex cereal and feed matrices and to extend the existing analytical scope to 167 pesticides. The co-extractives were reduced by the joint use of primary secondary amine (PSA) and octadecyl (C18), 75 mg and 50 mg/1 mL of acetonitrile extract, in the presence of MgSO(4), and thus the optimal recovery and analytical selectivity were obtained simultaneously. The new cleanup procedure was faster and easier to handle than our previously applied cleanup procedure. The overall recoveries of the pesticides from buckwheat and rye at the three spiking levels of 0.01, 0.05 and 0.25 mg kg(-1) were 96 ± 9% with relative standard deviations of 10 ± 4% on average. At the lowest spiking level of 0.01 mg kg(-1), 137 of 167 pesticide residues (82%) fulfilled the validation criteria with recoveries in the range of 70-120% and RSDs less or equal 20% whereas in the previous approach it was 93 out of 140 analytes (66%). The developed method was implemented in a routine analysis of approximately 900 real samples, providing an increased scope of the analysis, improved analytical performance parameters and improved ruggedness versus the previous approach. A total of 17% analyzed samples contained pesticide residues. There were 24 different compounds encountered in the samples, of which pirimiphos-methyl, tebuconazole, deltamethrin, and chlorpyrifos-methyl were the most frequent ones. Copyright © 2012 Elsevier B.V. All rights reserved.

  8. Handling of Solid Residues

    International Nuclear Information System (INIS)

    Medina Bermudez, Clara Ines

    1999-01-01

    The topic of solid residues is specifically of great interest and concern for the authorities, institutions and community that identify in them a true threat against the human health and the atmosphere in the related with the aesthetic deterioration of the urban centers and of the natural landscape; in the proliferation of vectorial transmitters of illnesses and the effect on the biodiversity. Inside the wide spectrum of topics that they keep relationship with the environmental protection, the inadequate handling of solid residues and residues dangerous squatter an important line in the definition of political and practical environmentally sustainable. The industrial development and the population's growth have originated a continuous increase in the production of solid residues; of equal it forms, their composition day after day is more heterogeneous. The base for the good handling includes the appropriate intervention of the different stages of an integral administration of residues, which include the separation in the source, the gathering, the handling, the use, treatment, final disposition and the institutional organization of the administration. The topic of the dangerous residues generates more expectation. These residues understand from those of pathogen type that are generated in the establishments of health that of hospital attention, until those of combustible, inflammable type, explosive, radio-active, volatile, corrosive, reagent or toxic, associated to numerous industrial processes, common in our countries in development

  9. Determinação de resíduos de pesticidas em plasma bovino por cromatografia gasosa-espectrometria de massas Pesticides residue determination in cattle plasma by gas chromatography-mass spectrometry

    Directory of Open Access Journals (Sweden)

    Daniele Fernanda Maffei

    2009-01-01

    Full Text Available An analytical method for the isolation based on matrix solid-phase dispersion technique and gas chromatographic determination of pesticides in cattle plasma is presented. It was fortified 0.25 g of plasma with pesticides and blended with 1 g each C18 and Na2SO4. The homogenized matter was transferred to a SPE cartridge, which contained 1 g of activated florisil with 5 mL acetonitrile. The analites were eluted under vaccum with 15 mL acetonitrile, the extract was analyzed by gas chromatography-mass spectrometry. The limit of quantification of the method was 0.04 mg L-1 for chlorphenvinfos and fipronil and 0.02 mg L-1 for cypermethrin..

  10. Natural radioactivity in petroleum residues

    International Nuclear Information System (INIS)

    Gazineu, M.H.P.; Gazineu, M.H.P.; Hazin, C.A.; Hazin, C.A.

    2006-01-01

    The oil extraction and production industry generates several types of solid and liquid wastes. Scales, sludge and water are typical residues that can be found in such facilities and that can be contaminated with Naturally Occurring Radioactive Material (N.O.R.M.). As a result of oil processing, the natural radionuclides can be concentrated in such residues, forming the so called Technologically Enhanced Naturally Occurring Radioactive Material, or T.E.N.O.R.M.. Most of the radionuclides that appear in oil and gas streams belong to the 238 U and 232 Th natural series, besides 40 K. The present work was developed to determine the radionuclide content of scales and sludge generated during oil extraction and production operations. Emphasis was given to the quantification of 226 Ra, 228 Ra and 40 K since these radionuclides,are responsible for most of the external exposure in such facilities. Samples were taken from the P.E.T.R.O.B.R.A.S. unity in the State of Sergipe, in Northeastern Brazil. They were collected directly from the inner surface of water pipes and storage tanks, or from barrels stored in the waste storage area of the E and P unit. The activity concentrations for 226 Ra, 228 Ra and 40 K were determined by using an HP Ge gamma spectrometric system. The results showed concentrations ranging from 42.7 to 2,110.0 kBq/kg for 226 Ra, 40.5 to 1,550.0 kBq/kg for 228 Ra, and 20.6 to 186.6 kBq/kg for 40 K. The results highlight the importance of determining the activity concentration of those radionuclides in oil residues before deciding whether they should be stored or discarded to the environment. (authors)

  11. Natural radioactivity in petroleum residues

    Energy Technology Data Exchange (ETDEWEB)

    Gazineu, M.H.P. [UNICAP, Dept. de Quimica, Recife (Brazil); Gazineu, M.H.P.; Hazin, C.A. [UFPE, Dept. de Energia Nuclear, Recife (Brazil); Hazin, C.A. [Centro Regional de Ciencias Nucleares/ CNEN, Recife (Brazil)

    2006-07-01

    The oil extraction and production industry generates several types of solid and liquid wastes. Scales, sludge and water are typical residues that can be found in such facilities and that can be contaminated with Naturally Occurring Radioactive Material (N.O.R.M.). As a result of oil processing, the natural radionuclides can be concentrated in such residues, forming the so called Technologically Enhanced Naturally Occurring Radioactive Material, or T.E.N.O.R.M.. Most of the radionuclides that appear in oil and gas streams belong to the {sup 238}U and {sup 232}Th natural series, besides 40 K. The present work was developed to determine the radionuclide content of scales and sludge generated during oil extraction and production operations. Emphasis was given to the quantification of {sup 226}Ra, {sup 228}Ra and 40 K since these radionuclides,are responsible for most of the external exposure in such facilities. Samples were taken from the P.E.T.R.O.B.R.A.S. unity in the State of Sergipe, in Northeastern Brazil. They were collected directly from the inner surface of water pipes and storage tanks, or from barrels stored in the waste storage area of the E and P unit. The activity concentrations for {sup 226}Ra, {sup 228}Ra and 40 K were determined by using an HP Ge gamma spectrometric system. The results showed concentrations ranging from 42.7 to 2,110.0 kBq/kg for {sup 226}Ra, 40.5 to 1,550.0 kBq/kg for {sup 228}Ra, and 20.6 to 186.6 kBq/kg for 40 K. The results highlight the importance of determining the activity concentration of those radionuclides in oil residues before deciding whether they should be stored or discarded to the environment. (authors)

  12. [Residual neuromuscular blockade].

    Science.gov (United States)

    Fuchs-Buder, T; Schmartz, D

    2017-06-01

    Even small degrees of residual neuromuscular blockade, i. e. a train-of-four (TOF) ratio >0.6, may lead to clinically relevant consequences for the patient. Especially upper airway integrity and the ability to swallow may still be markedly impaired. Moreover, increasing evidence suggests that residual neuromuscular blockade may affect postoperative outcome of patients. The incidence of these small degrees of residual blockade is relatively high and may persist for more than 90 min after a single intubating dose of an intermediately acting neuromuscular blocking agent, such as rocuronium and atracurium. Both neuromuscular monitoring and pharmacological reversal are key elements for the prevention of postoperative residual blockade.

  13. TENORM: Wastewater Treatment Residuals

    Science.gov (United States)

    Water and wastes which have been discharged into municipal sewers are treated at wastewater treatment plants. These may contain trace amounts of both man-made and naturally occurring radionuclides which can accumulate in the treatment plant and residuals.

  14. Conduct disorders.

    Science.gov (United States)

    Buitelaar, Jan K; Smeets, Kirsten C; Herpers, Pierre; Scheepers, Floor; Glennon, Jeffrey; Rommelse, Nanda N J

    2013-02-01

    Conduct disorder (CD) is a frequently occurring psychiatric disorder characterized by a persistent pattern of aggressive and non-aggressive rule breaking antisocial behaviours that lead to considerable burden for the patients themselves, their family and society. This review paper updates diagnostic and therapeutic approaches to CD in the light of the forthcoming DSM-5 definition. The diagnostic criteria for CD will remain unchanged in DSM-5, but the introduction of a specifier of CD with a callous-unemotional (CU) presentation is new. Linked to this, we discuss the pros and cons of various other ways to subtype aggression/CD symptoms. Existing guidelines for CD are, with few exceptions, already of a relatively older date and emphasize that clinical assessment should be systematic and comprehensive and based on a multi-informant approach. Non-medical psychosocial interventions are recommended as the first option for the treatment of CD. There is a role for medication in the treatment of comorbid syndromes and/or in case of insufficient response to psychosocial interventions and severe and dangerous aggressive and violent behaviours.

  15. Experimental determination of thermal conductivity and gap conductance of fuel rod for HTGR

    International Nuclear Information System (INIS)

    Kikuchi, Teruo; Iwamoto, Kazumi; Ikawa, Katsuichi; Ishimoto, Kiyoshi

    1985-01-01

    The thermal conductivity of fuel compacts and the gap conductance between the fuel compact and the graphite sleeve in fuel rods for a high-temperature gas-cooled reactor (HTGR) were measured by the center heating method. These measurements were made as functions of volume percent particle loading and temperature for thermal conductivity and as functions of gap distance and gas composition for gap conductance. The thermal conductivity of fuel compacts decreases with increasing temperature and with increasing particle loading. The gap conductance increases with increasing temperature and decrease with increasing gap distance. A good gap conductance was observed with helium fill gas. It was seen that the gap conductance was dependent on the thermal conductivity of fill gas and conductance by radiation and could be neglected the conductance through solid-solid contact points of fuel compact and graphite sleeve. (author)

  16. Residuation in orthomodular lattices

    Directory of Open Access Journals (Sweden)

    Chajda Ivan

    2017-04-01

    Full Text Available We show that every idempotent weakly divisible residuated lattice satisfying the double negation law can be transformed into an orthomodular lattice. The converse holds if adjointness is replaced by conditional adjointness. Moreover, we show that every positive right residuated lattice satisfying the double negation law and two further simple identities can be converted into an orthomodular lattice. In this case, also the converse statement is true and the corresponence is nearly one-to-one.

  17. Calcination/dissolution residue treatment

    International Nuclear Information System (INIS)

    Knight, R.C.; Creed, R.F.; Patello, G.K.; Hollenberg, G.W.; Buehler, M.F.; O'Rourke, S.M.; Visnapuu, A.; McLaughlin, D.F.

    1994-09-01

    Currently, high-level wastes are stored underground in steel-lined tanks at the Hanford site. Current plans call for the chemical pretreatment of these wastes before their immobilization in stable glass waste forms. One candidate pretreatment approach, calcination/dissolution, performs an alkaline fusion of the waste and creates a high-level/low-level partition based on the aqueous solubilities of the components of the product calcine. Literature and laboratory studies were conducted with the goal of finding a residue treatment technology that would decrease the quantity of high-level waste glass required following calcination/dissolution waste processing. Four elements, Fe, Ni, Bi, and U, postulated to be present in the high-level residue fraction were identified as being key to the quantity of high-level glass formed. Laboratory tests of the candidate technologies with simulant high-level residues showed reductive roasting followed by carbonyl volatilization to be successful in removing Fe, Ni, and Bi. Subsequent bench-scale tests on residues from calcination/dissolution processing of genuine Hanford Site tank waste showed Fe was separated with radioelement decontamination factors of 70 to 1,000 times with respect to total alpha activity. Thermodynamic analyses of the calcination of five typical Hanford Site tank waste compositions also were performed. The analyses showed sodium hydroxide to be the sole molten component in the waste calcine and emphasized the requirement for waste blending if fluid calcines are to be achieved. Other calcine phases identified in the thermodynamic analysis indicate the significant thermal reconstitution accomplished in calcination

  18. Characterization of Hospital Residuals

    International Nuclear Information System (INIS)

    Blanco Meza, A.; Bonilla Jimenez, S.

    1997-01-01

    The main objective of this investigation is the characterization of the solid residuals. A description of the handling of the liquid and gassy waste generated in hospitals is also given, identifying the source where they originate. To achieve the proposed objective the work was divided in three stages: The first one was the planning and the coordination with each hospital center, in this way, to determine the schedule of gathering of the waste can be possible. In the second stage a fieldwork was made; it consisted in gathering the quantitative and qualitative information of the general state of the handling of residuals. In the third and last stage, the information previously obtained was organized to express the results as the production rate per day by bed, generation of solid residuals for sampled services, type of solid residuals and density of the same ones. With the obtained results, approaches are settled down to either determine design parameters for final disposition whether for incineration, trituration, sanitary filler or recycling of some materials, and storage politics of the solid residuals that allow to determine the gathering frequency. The study concludes that it is necessary to improve the conditions of the residuals handling in some aspects, to provide the cleaning personnel of the equipment for gathering disposition and of security, minimum to carry out this work efficiently, and to maintain a control of all the dangerous waste, like sharp or polluted materials. In this way, an appreciable reduction is guaranteed in the impact on the atmosphere. (Author) [es

  19. Classification of crops grown in or imported into the European Union for pesticide residue assessment

    NARCIS (Netherlands)

    Velde-Koerts T van der; Muller E; Ossendorp BHC; Plantenziektenkundige dienst; SIR; Plantenziektenkundige Dienst

    2003-01-01

    An important aspect of food safety is the control of pesticide residues on food. Pesticide residue assessments are conducted to establish legal limits, known as maximum residue limits (MRLs), for pesticide residues in plant and animal commodities. In the EC guidelines for pesticide

  20. Sensitivity analysis and economic optimization studies of inverted five-spot gas cycling in gas condensate reservoir

    Science.gov (United States)

    Shams, Bilal; Yao, Jun; Zhang, Kai; Zhang, Lei

    2017-08-01

    Gas condensate reservoirs usually exhibit complex flow behaviors because of propagation response of pressure drop from the wellbore into the reservoir. When reservoir pressure drops below the dew point in two phase flow of gas and condensate, the accumulation of large condensate amount occurs in the gas condensate reservoirs. Usually, the saturation of condensate accumulation in volumetric gas condensate reservoirs is lower than the critical condensate saturation that causes trapping of large amount of condensate in reservoir pores. Trapped condensate often is lost due to condensate accumulation-condensate blockage courtesy of high molecular weight, heavy condensate residue. Recovering lost condensate most economically and optimally has always been a challenging goal. Thus, gas cycling is applied to alleviate such a drastic loss in resources. In gas injection, the flooding pattern, injection timing and injection duration are key parameters to study an efficient EOR scenario in order to recover lost condensate. This work contains sensitivity analysis on different parameters to generate an accurate investigation about the effects on performance of different injection scenarios in homogeneous gas condensate system. In this paper, starting time of gas cycling and injection period are the parameters used to influence condensate recovery of a five-spot well pattern which has an injection pressure constraint of 3000 psi and production wells are constraint at 500 psi min. BHP. Starting injection times of 1 month, 4 months and 9 months after natural depletion areapplied in the first study. The second study is conducted by varying injection duration. Three durations are selected: 100 days, 400 days and 900 days. In miscible gas injection, miscibility and vaporization of condensate by injected gas is more efficient mechanism for condensate recovery. From this study, it is proven that the application of gas cycling on five-spot well pattern greatly enhances condensate recovery

  1. THERMAL CONDUCTIVITY ANALYSIS OF GASES

    Science.gov (United States)

    Clark, W.J.

    1949-06-01

    This patent describes apparatus for the quantitative analysis of a gaseous mixture at subatmospheric pressure by measurement of its thermal conductivity. A heated wire forms one leg of a bridge circuit, while the gas under test is passed about the wire at a constant rate. The bridge unbalance will be a measure of the change in composition of the gas, if compensation is made for the effect due to gas pressure change. The apparatus provides a voltage varying with fluctuations of pressure in series with the indicating device placed across the bridge, to counterbalance the voltage change caused by fluctuations in the pressure of the gaseous mixture.

  2. Means for producing gas

    Energy Technology Data Exchange (ETDEWEB)

    Reichhelm, G.L.

    1929-01-22

    This patent describes a gas-generating apparatus which works in combination with a gas-generating receptacle. The process requires a means for supplying finely divided carbon to said receptable, means for supplying a flame under pressure to hold said carbon in suspension, a conduit for conducting the combustible gas produced from said receptacle, and synchronously operating mechanical means for controlling said carbon-supplying means and said flame-supplying means.

  3. Treatment and use of air pollution control residues from MSW incineration: an overview.

    Science.gov (United States)

    Quina, Margarida J; Bordado, João C; Quinta-Ferreira, Rosa M

    2008-11-01

    This work reviews strategies for the management of municipal solid waste incineration (MSWI) residues, particularly solid particles collected from flue gases. These tiny particles may be retained by different equipment, with or without additives (lime, activated carbon, etc.), and depending on the different possible combinations, their properties may vary. In industrial plants, the most commonly used equipment for heat recovery and the cleaning of gas emissions are: heat recovery devices (boiler, superheater and economiser); dry, semidry or wet scrubbers; electrostatic precipitators; bag filters; fabric filters, and cyclones. In accordance with the stringent regulations in force in developed countries, these residues are considered hazardous, and therefore must be treated before being disposed of in landfills. Nowadays, research is being conducted into specific applications for these residues in order to prevent landfill practices. There are basically two possible ways of handling these residues: landfill after adequate treatment or recycling as a secondary material. The different types of treatment may be grouped into three categories: separation processes, solidification/stabilization, and thermal methods. These residues generally have limited applications, mainly due to the fact that they tend to contain large quantities of soluble salts (NaCl, KCl, calcium compounds), significant amounts of toxic heavy metals (Pb, Zn, Cr, Cu, Ni, Cd) in forms that may easily leach out, and trace quantities of very toxic organic compounds (dioxin, furans). The most promising materials for recycling this residue are ceramics and glass-ceramic materials. The main purpose of the present paper is to review the published literature in this field. A range of studies have been summarized in a series of tables focusing upon management strategies used in various countries, waste composition, treatment processes and possible applications.

  4. Radiative thermal conduction fronts

    International Nuclear Information System (INIS)

    Borkowski, K.J.; Balbus, S.A.; Fristrom, C.C.

    1990-01-01

    The discovery of the O VI interstellar absorption lines in our Galaxy by the Copernicus observatory was a turning point in our understanding of the Interstellar Medium (ISM). It implied the presence of widespread hot (approx. 10 to the 6th power K) gas in disk galaxies. The detection of highly ionized species in quasi-stellar objects' absorption spectra may be the first indirect observation of this hot phase in external disk galaxies. Previous efforts to understand extensive O VI absorption line data from our Galaxy were not very successful in locating the regions where this absorption originates. The location at interfaces between evaporating ISM clouds and hot gas was favored, but recent studies of steady-state conduction fronts in spherical clouds by Ballet, Arnaud, and Rothenflug (1986) and Bohringer and Hartquist (1987) rejected evaporative fronts as the absorption sites. Researchers report here on time-dependent nonequilibrium calculations of planar conductive fronts whose properties match well with observations, and suggest reasons for the difference between the researchers' results and the above. They included magnetic fields in additional models, not reported here, and the conclusions are not affected by their presence

  5. Review of environmental exposure concentrations of chemical warfare agent residues and associated the fish community risk following the construction and completion of the Nord Stream gas pipeline between Russia and Germany.

    Science.gov (United States)

    Sanderson, Hans; Fauser, Patrik; Rahbek, Malene; Larsen, Jørn Bo

    2014-08-30

    This paper compiles all the measured chemical warfare agent (CWA) concentrations found in relation to the Nord Stream pipeline work in Danish waters for the past 5 years. Sediment and biota sampling were performed along the pipeline route in four campaigns, prior to (in 2008 and 2010), during (in 2011) and after (in 2012) the construction work. No parent CWAs were detected in the sediments. Patchy residues of CWA degradation products of Adamsite, Clark I, phenyldichloroarsine, trichloroarsine and Lewisite II, were detected in a total of 29 of the 391 sediment samples collected and analyzed the past 5 years. The cumulative fish community risk quotient for the different locations, calculated as a sum of background and added risk, ranged between 0 and 0.017 suggesting a negligible acute CWA risk toward the fish community. The added risk from sediment disturbance in relation to construction of the pipelines represents less than 2% of the total risk in the areas with the highest calculated risk. The analyses of benthic infauna corroborate the finding of CWA related low risk across the years. There was no significant difference in CWA risk before (2008) and after the pipeline construction (2012). Copyright © 2014 Elsevier B.V. All rights reserved.

  6. EFFECTS OF MUCUNA ( MUCUNA UTILIS L.) RESIDUE ...

    African Journals Online (AJOL)

    The field experiment was conducted at two locations: University of Agriculture, Abeokuta (UNAAB) and Olowo-Papa (OP) in Ogun state both in Forest-savannah transition zone of Nigeria to investigate the response of three upland rice cultivars (O.sativa) to mucuna residue incorporation and Nitrogen (N) fertilizer and the ...

  7. Valorization of Furfural Residue by Hydrothermal Carbonization

    DEFF Research Database (Denmark)

    Yue, Fen; Zhang, Jia; Pedersen, Christian Marcus

    2017-01-01

    Furfural residue (FR) is a low-cost by-product generated in the furfural production from corncobs, which is mainly composed of cellulose and lignin. In this report, hydrothermal carbonization (HTC) of deashed FR was conducted at various reaction temperatures (200, 220 and 240 °C) and reaction tim...

  8. Residual-stress measurements

    Energy Technology Data Exchange (ETDEWEB)

    Ezeilo, A.N.; Webster, G.A. [Imperial College, London (United Kingdom); Webster, P.J. [Salford Univ. (United Kingdom)

    1997-04-01

    Because neutrons can penetrate distances of up to 50 mm in most engineering materials, this makes them unique for establishing residual-stress distributions non-destructively. D1A is particularly suited for through-surface measurements as it does not suffer from instrumental surface aberrations commonly found on multidetector instruments, while D20 is best for fast internal-strain scanning. Two examples for residual-stress measurements in a shot-peened material, and in a weld are presented to demonstrate the attractive features of both instruments. (author).

  9. Method for residual household waste composition studies.

    Science.gov (United States)

    Sahimaa, Olli; Hupponen, Mari; Horttanainen, Mika; Sorvari, Jaana

    2015-12-01

    The rising awareness of decreasing natural resources has brought forward the idea of a circular economy and resource efficiency in Europe. As a part of this movement, European countries have identified the need to monitor residual waste flows in order to make recycling more efficient. In Finland, studies on the composition of residual household waste have mostly been conducted using different methods, which makes the comparison of the results difficult. The aim of this study was to develop a reliable method for residual household waste composition studies. First, a literature review on European study methods was performed. Also, 19 Finnish waste composition studies were compared in order to identify the shortcomings of the current Finnish residual household waste composition data. Moreover, the information needs of different waste management authorities concerning residual household waste were studied through a survey and personal interviews. Stratification, sampling, the classification of fractions and statistical analysis were identified as the key factors in a residual household waste composition study. The area studied should be divided into non-overlapping strata in order to decrease the heterogeneity of waste and enable comparisons between different waste producers. A minimum of six subsamples, each 100 kg, from each stratum should be sorted. Confidence intervals for each waste category should be determined in order to evaluate the applicability of the results. A new three-level classification system was created based on Finnish stakeholders' information needs and compared to four other European waste composition study classifications. Copyright © 2015 Elsevier Ltd. All rights reserved.

  10. Testing the efficiency of extraction of incurred residues from soil with optimized multi-residue method.

    Science.gov (United States)

    Suszter, Gabriella K; Ambrus, Árpád

    2017-08-03

    The reproducibility of extraction of residues from spiked soil samples and from soils containing incurred residues was tested with 14 C-labeled test compounds of different physical-chemical properties. Nearly 100% of the compounds added to the sample before extraction could be recovered with an average reproducibility relative standard deviation (CV) of 5.4%. The additional steps of the determination process (cleanup, evaporation, etc.) contributed to the major part of the variability of the results (CV = 10-20%). The incurred residues were most efficiently extracted with acetone for 30 min followed by the mixture of acetone/ethyl acetate 1:1 for additional 30 min. However, they could only be recovered at various extent (64-90% of total residues), underlying the importance of testing the efficiency of extraction. The residues were identified and quantified by gas chromatography applying thermionic detector. The performance parameters of the method complied with the international method validation guidelines, and they proved to be robust and suitable for determination of pesticide residues in soils of widely different physical-chemical properties.

  11. Residual photoconductivity spectra in InAs/AlSb quantum well heterostructures

    International Nuclear Information System (INIS)

    Aleshkin, V.Ya.; Gavrilenko, V.I.; Gaponova, D.M.; Ikonnikov, A.V.; Marem'yanin, K.V.; Morozov, S.V.; Sadof'ev, Yu.G.; Johnson, S.R.; Zhang, Y.-H.

    2005-01-01

    The residual photoconductivity in AlSb/InAs/AlSb heterostructures with two-dimensional electron gas in InAs quantum wells has been investigated at T = 4.2 K. At the excitation by IR radiation ℎω = 0.6-1.2 eV the positive residual conductivity has been observed, the effect being related to the photoionization of deep donors. At shorter wavelengths a negative residual photoconductivity is observed resulting from the band-gap excitation of electron-hole pairs and subsequent separation of electron and holes by the built-in electric field, the electron capture by ionized donors and the hole recombination with two-dimensional electrons in InAs. At ℎω > 3.1 eV the abrupt drop of negative photoconductivity has been discovered. This effect is attributed to the switching-on a new channel of photoionization of deep donors in AlSb due to electron transitions into the energy band above the conduction one [ru

  12. Influence of post-harvest crop residue fires on surface ozone mixing ratios in the N.W. IGP analyzed using 2 years of continuous in situ trace gas measurements

    Science.gov (United States)

    Kumar, V.; Sarkar, C.; Sinha, V.

    2016-04-01

    O3, CO, and NOx affect air quality and tropospheric chemistry but factors that control them in the densely populated N.W. Indo-Gangetic Plain (IGP) are poorly understood. This work presents the first simultaneous 2 year long in situ data set acquired from August 2011 to September 2013 at a N.W. IGP site (30.667°N, 76.729°E; 310 m asl). We investigate the impact of emissions and meteorology on the diel and seasonal variability of O3, CO, and NOx. Regional post-harvest crop residue fires contribute majorly to an enhancement of 19 ppb in hourly averaged ozone concentrations under similar meteorological conditions in summer and 7 ppb under conditions of lower radiation during the post monsoon. d[O3]/dt (from sunrise to daytime O3 maxima) was highest during periods influenced by post-harvest fires in post monsoon season (9.2 ppb h-1) and lowest during monsoon season (4.1 ppb h-1). Analysis of air mass clusters revealed that enhanced chemical formation of O3 and not transport was the driver of the summertime and post monsoon ambient O3 maxima. Despite having high daytime NOx (>12 ppb) and CO (>440 ppb) in winter, average daytime O3 was less than 40 ppb due to reduced photochemistry and fog. Average daytime O3 during the monsoon was less than 45 ppb due to washout of precursors and suppressed photochemistry due to cloud cover. The 8 h ambient air quality O3 standard was violated on 451 days in the period August 2011-September 2013. The results show that substantial mitigation efforts are required to reduce regional O3 pollution in the N.W. IGP.

  13. Nitrogen mineralization from organic residues: research opportunities.

    Science.gov (United States)

    Cabrera, M L; Kissel, D E; Vigil, M F

    2005-01-01

    Research on nitrogen (N) mineralization from organic residues is important to understand N cycling in soils. Here we review research on factors controlling net N mineralization as well as research on laboratory and field modeling efforts, with the objective of highlighting areas with opportunities for additional research. Among the factors controlling net N mineralization are organic composition of the residue, soil temperature and water content, drying and rewetting events, and soil characteristics. Because C to N ratio of the residue cannot explain all the variability observed in N mineralization among residues, considerable effort has been dedicated to the identification of specific compounds that play critical roles in N mineralization. Spectroscopic techniques are promising tools to further identify these compounds. Many studies have evaluated the effect of temperature and soil water content on N mineralization, but most have concentrated on mineralization from soil organic matter, not from organic residues. Additional work should be conducted with different organic residues, paying particular attention to the interaction between soil temperature and water content. One- and two-pool exponential models have been used to model N mineralization under laboratory conditions, but some drawbacks make it difficult to identify definite pools of mineralizable N. Fixing rate constants has been used as a way to eliminate some of these drawbacks when modeling N mineralization from soil organic matter, and may be useful for modeling N mineralization from organic residues. Additional work with more complex simulation models is needed to simulate both gross N mineralization and immobilization to better estimate net N mineralized from organic residues.

  14. Classification of crops grown in or imported into the European Union for pesticide residue assessment

    OpenAIRE

    Velde-Koerts T van der; Muller E; Ossendorp BHC; Plantenziektenkundige dienst; SIR; Plantenziektenkundige Dienst

    2003-01-01

    An important aspect of food safety is the control of pesticide residues on food. Pesticide residue assessments are conducted to establish legal limits, known as maximum residue limits (MRLs), for pesticide residues in plant and animal commodities. In the EC guidelines for pesticide residue assessment, the so-called Lundehn document, agricultural crops are classified into groups in which results are considered to be comparable. Within these groups, the results for one crop may be extrapolated,...

  15. Designing with residual materials

    NARCIS (Netherlands)

    Walhout, W.; Wever, R.; Blom, E.; Addink-Dölle, L.; Tempelman, E.

    2013-01-01

    Many entrepreneurial businesses have attempted to create value based on the residual material streams of third parties. Based on ‘waste’ materials they designed products, around which they built their company. Such activities have the potential to yield sustainable products. Many of such companies

  16. Air-assisted liquid-liquid microextraction-gas chromatography-flame ionisation detection: a fast and simple method for the assessment of triazole pesticides residues in surface water, cucumber, tomato and grape juices samples.

    Science.gov (United States)

    Farajzadeh, Mir Ali; Khoshmaram, Leila

    2013-12-01

    A recently reported microextraction technique namely air-assisted liquid-liquid microextraction (AALLME) has been described for the extraction/preconcentration of some triazole pesticides from different samples prior to gas chromatography-flame ionisation detection (GC-FID). This technique is similar to dispersive liquid-liquid microextraction (DLLME) but in this method there is no need to use a disperser solvent and also volume of the used extraction solvent is less than DLLME. In this study, toluene with a density lower than that of water was used as an extraction solvent. Under the optimum extraction conditions, the method showed wide linear ranges with R(2)>0.996 and low limits of detection and quantification between 0.53-1.13 and 1.76-3.77 ng mL(-1), respectively. Enrichment factors (EFs) and extraction recoveries (ERs) were in the ranges of 713-808 and 100-113%, respectively. Relative standard deviations (RSDs) for the extraction of 25 and 250 ng mL(-1) of each selected triazole pesticide were less than 7% for intra-day (n=6) and inter-days (n=5) precision. The method was successfully used for analytes determination in different surface water, grape juice, cucumber, and tomato samples. Copyright © 2013 Elsevier Ltd. All rights reserved.

  17. Comparative effects of plant residues and NPK fertilizer on soil ...

    African Journals Online (AJOL)

    Field experiments were conducted at two locations in 2001 and 2002 on acidic Ultisol of Southeast Nigeria to assess the effects of amending soil with plant residues on soil physical and chemical properties. The soil amendment treatments compared were natural fallow, wood ash at 6 tha-1, peanut residue at 12 tha-1, ...

  18. Comparative effect of plant residues and NPK fertilizer on nutrient ...

    African Journals Online (AJOL)

    Field experiments were conducted at two locations in 2001 and 2002 on acidic Ultisol of southeast Nigeria to access the effect of amending soil with plant residues on maize performance. The soil amendment treatments compared were natural fallow, wood ash at 6 tha-1, peanut residue at 12 tha-1, combination of wood ash ...

  19. Residue analysis of organochlorine pesticides in water and ...

    African Journals Online (AJOL)

    Residue analysis of organochlorine pesticides in water and sediments from Agboyi Creek, Lagos. AB Williams. Abstract. Microlayer water, mixed layer water, epipellic and benthic sediments were collected from Agboyi Creek, Lagos to analyse organochlorine pesticide residues. Sampling was conducted between December ...

  20. Evaluation of pesticide residues in fruits and vegetables from Algeria.

    Science.gov (United States)

    Mebdoua, Samira; Lazali, Mohamed; Ounane, Sidi Mohamed; Tellah, Sihem; Nabi, Fahima; Ounane, Ghania

    2017-06-01

    A total of 160 samples of 13 types of fresh fruits and vegetables from domestic production and import were analysed to detect the presence of pesticide residues. Analysis was performed by multi-residual extraction followed by gas chromatography-mass spectrometry. In 42.5% of the tested samples, no residues were found and 12.5% of samples contained pesticide residues above maximum residue limits. Risk assessment for long-term exposure was done for all pesticides detected in this study. Except chlorpyrifos and lambda-cyhalothrin, exposure to pesticides from vegetables and fruits was below 1% of the acceptable daily intake. Short-term exposure assessment revealed that in seven pesticide/commodity combinations, including three pesticides (chlorpyrifos, deltamethrin and lambda-cyhalothrin), the acute reference dose had been exceeded.

  1. Method to induce a conductivity type in a semiconductor

    International Nuclear Information System (INIS)

    Aboaf, J.A.; Sedgwick, T.O.

    1977-01-01

    The invention deals with a method in which one can produce a region of a desired type of conductivity in a semiconductor as is required for, e.g., field effect transistors. A metal oxide layer combination consisting of several metal oxides is thus deposited on the semiconductor. This is carried out according to the invention in a non-oxidizing atmosphere at temperatures at which the metal oxides do not diffuse into the semiconductor. The sign and degree of the induced conductivity type is adjusted by dosed depositing of the individual metal oxides related to one another. The gaseous metal oxides due to heating, mixed with a non-oxidizing gas are added in compounds to the semiconductor heated to depositing temperature. These compounds decompose at the depositing temperature into the metal oxide and a gaseous residual component. The semiconductor consists of silicon, and nitrogen is used as carrier gas; when depositing aluminium oxide, gaseous aluminium isopropoxide is added; when depositing silicon dioxide, gaseous tetra-ethyl orthosilicate. (ORU) [de

  2. Residual stress characterization of steel TIG welds by neutron diffraction and by residual magnetic stray field mappings

    International Nuclear Information System (INIS)

    Stegemann, Robert; Cabeza, Sandra; Lyamkin, Viktor; Bruno, Giovanni; Pittner, Andreas; Wimpory, Robert; Boin, Mirko; Kreutzbruck, Marc

    2017-01-01

    The residual stress distribution of tungsten inert gas welded S235JRC+C plates was determined by means of neutron diffraction (ND). Large longitudinal residual stresses with maxima around 600 MPa were found. With these results as reference, the evaluation of residual stress with high spatial resolution GMR (giant magneto resistance) sensors was discussed. The experiments performed indicate a correlation between changes in residual stresses (ND) and the normal component of local residual magnetic stray fields (GMR). Spatial variations in the magnetic field strength perpendicular to the welds are in the order of the magnetic field of the earth. - Highlights: • Comparison of magnetic microstructure with neutron diffraction stress analysis. • High spatial resolution magnetic stray field images of hypereutectoid TIG welds. • Spatial variations of the stray fields are below the magnetic field of the earth. • GMR spin valve gradiometer arrays adapted for the evaluation of magnetic microstructures. • Magnetic stray fields are closely linked to microstructure of the material.

  3. Residual stress characterization of steel TIG welds by neutron diffraction and by residual magnetic stray field mappings

    Energy Technology Data Exchange (ETDEWEB)

    Stegemann, Robert, E-mail: Robert.Stegemann@bam.de [Bundesanstalt für Materialforschung und -prüfung (BAM), Unter den Eichen 87, 12200 Berlin (Germany); Cabeza, Sandra; Lyamkin, Viktor; Bruno, Giovanni; Pittner, Andreas [Bundesanstalt für Materialforschung und -prüfung (BAM), Unter den Eichen 87, 12200 Berlin (Germany); Wimpory, Robert; Boin, Mirko [HZB Helmholtz-Zentrum Berlin, Hahn-Meitner-Platz 1, 14109 Berlin (Germany); Kreutzbruck, Marc [Bundesanstalt für Materialforschung und -prüfung (BAM), Unter den Eichen 87, 12200 Berlin (Germany); IKT, University of Stuttgart, Pfaffenwaldring 32, 70569 Stuttgart (Germany)

    2017-03-15

    The residual stress distribution of tungsten inert gas welded S235JRC+C plates was determined by means of neutron diffraction (ND). Large longitudinal residual stresses with maxima around 600 MPa were found. With these results as reference, the evaluation of residual stress with high spatial resolution GMR (giant magneto resistance) sensors was discussed. The experiments performed indicate a correlation between changes in residual stresses (ND) and the normal component of local residual magnetic stray fields (GMR). Spatial variations in the magnetic field strength perpendicular to the welds are in the order of the magnetic field of the earth. - Highlights: • Comparison of magnetic microstructure with neutron diffraction stress analysis. • High spatial resolution magnetic stray field images of hypereutectoid TIG welds. • Spatial variations of the stray fields are below the magnetic field of the earth. • GMR spin valve gradiometer arrays adapted for the evaluation of magnetic microstructures. • Magnetic stray fields are closely linked to microstructure of the material.

  4. Thermal Adsorption Processing Of Hydrocarbon Residues

    Directory of Open Access Journals (Sweden)

    Sudad H. Al.

    2017-04-01

    Full Text Available The raw materials of secondary catalytic processes must be pre-refined. Among these refining processes are the deasphalting and demetallization including their thermo adsorption or thermo-contact adsorption variety. In oil processing four main processes of thermo-adsorption refining of hydrocarbon residues are used ART Asphalt Residual Treating - residues deasphaltizing 3D Discriminatory Destructive Distillation developed in the US ACT Adsorption-Contact Treatment and ETCC Express Thermo-Contact Cracking developed in Russia. ART and ACT are processes with absorbers of lift type reactor while 3D and ETCC processes are with an adsorbing reactor having ultra-short contact time of the raw material with the adsorbent. In all these processes refining of hydrocarbon residues is achieved by partial Thermo-destructive transformations of hydrocarbons and hetero-atomic compounds with simultaneous adsorption of the formed on the surface of the adsorbents resins asphaltene and carboids as well as metal- sulphur - and nitro-organic compounds. Demetallized and deasphalted light and heavy gas oils or their mixtures are a quality raw material for secondary deepening refining processes catalytic and hydrogenation cracking etc. since they are characterized by low coking ability and low content of organometallic compounds that lead to irreversible deactivation of the catalysts of these deepening processes.

  5. Landfill Mining of Shredder Residues

    DEFF Research Database (Denmark)

    Hansen, Jette Bjerre; Hyks, Jiri; Shabeer Ahmed, Nassera

    In Denmark, shredder residues (SR) are classified as hazardous waste and until January 2012 the all SR were landfilled. It is estimated that more than 1.8 million tons of SR have been landfilled in mono cells. This paper describes investigations conducted at two Danish landfills. SR were excavated...... from the landfills and size fractionated in order to recover potential resources such as metal and energy and to reduce the amounts of SR left for re-landfilling. Based on the results it is estimated that 60-70% of the SR excavated could be recovered in terms of materials or energy. Only a fraction...... with particle size less than 5 mm needs to be re-landfilled at least until suitable techniques are available for recovery of materials with small particle sizes....

  6. Residual stresses in material processing

    Science.gov (United States)

    Kozaczek, K. J.; Watkins, T. R.; Hubbard, C. R.; Wang, Xun-Li; Spooner, S.

    Material manufacturing processes often introduce residual stresses into the product. The residual stresses affect the properties of the material and often are detrimental. Therefore, the distribution and magnitude of residual stresses in the final product are usually an important factor in manufacturing process optimization or component life prediction. The present paper briefly discusses the causes of residual stresses. It then addresses the direct, nondestructive methods of residual stress measurement by X ray and neutron diffraction. Examples are presented to demonstrate the importance of residual stress measurement in machining and joining operations.

  7. Retained Gas Sampling Results for the Flammable Gas Program

    Energy Technology Data Exchange (ETDEWEB)

    J.M. Bates; L.A. Mahoney; M.E. Dahl; Z.I. Antoniak

    1999-11-18

    The key phenomena of the Flammable Gas Safety Issue are generation of the gas mixture, the modes of gas retention, and the mechanisms causing release of the gas. An understanding of the mechanisms of these processes is required for final resolution of the safety issue. Central to understanding is gathering information from such sources as historical records, tank sampling data, tank process data (temperatures, ventilation rates, etc.), and laboratory evaluations conducted on tank waste samples.

  8. Retained Gas Sampling Results for the Flammable Gas Program

    International Nuclear Information System (INIS)

    Bates, J.M.; Mahoney, L.A.; Dahl, M.E.; Antoniak, Z.I.

    1999-01-01

    The key phenomena of the Flammable Gas Safety Issue are generation of the gas mixture, the modes of gas retention, and the mechanisms causing release of the gas. An understanding of the mechanisms of these processes is required for final resolution of the safety issue. Central to understanding is gathering information from such sources as historical records, tank sampling data, tank process data (temperatures, ventilation rates, etc.), and laboratory evaluations conducted on tank waste samples

  9. SRC Residual fuel oils

    Science.gov (United States)

    Tewari, Krishna C.; Foster, Edward P.

    1985-01-01

    Coal solids (SRC) and distillate oils are combined to afford single-phase blends of residual oils which have utility as fuel oils substitutes. The components are combined on the basis of their respective polarities, that is, on the basis of their heteroatom content, to assure complete solubilization of SRC. The resulting composition is a fuel oil blend which retains its stability and homogeneity over the long term.

  10. Composition of carbonization residues

    Energy Technology Data Exchange (ETDEWEB)

    Hupfer; Leonhardt

    1943-11-30

    This report gave a record of the composition of several samples of residues from carbonization of various hydrogenation residue from processing some type of coal or tar in the Bergius process. These included Silesian bituminous coal processed at 600 atm. with iron catalyst, in one case to produce gasoline and middle oil and in another case to produce heavy oil excess, Scholven coal processed at 250 atm. with tin oxalate and chlorine catalyst, Bruex tar processed in a 10-liter oven using iron catalyst, and a pitch mixture from Welheim processed in a 10-liter over using iron catalyst. The values gathered were compared with a few corresponding values estimated for Boehlen tar and Gelsenberg coal based on several assumptions outlined in the report. The data recorded included percentage of ash in the dry residue and percentage of carbon, hydrogen, oxygen, nitrogen, chlorine, total sulfur, and volatile sulfur. The percentage of ash varied from 21.43% in the case of Bruex tar to 53.15% in the case of one of the Silesian coals. Percentage of carbon varied from 44.0% in the case of Scholven coal to 78.03% in the case of Bruex tar. Percentage of total sulfur varied from 2.28% for Bruex tar to a recorded 5.65% for one of the Silesian coals and an estimated 6% for Boehlen tar. 1 table.

  11. Life cycle assessment of shredder residue management

    DEFF Research Database (Denmark)

    Boldrin, Alessio; Damgaard, Anders; Brogaard, Line Kai-Sørensen

    This report provides a life-cycle assessment (LCA) of the treatment of shredder residue (SR) in Denmark. The LCA was conducted for the Environmental Protection Agency by DTU Environment in the period March-July 2014, as part of a service agreement between the Danish Environmental Protection Agency...... wood waste, wood waste for recycling and district heating pipes. The LCA was conducted using the EASETECH LCA model developed by DTU Environment for the environmental assessment of waste management systems and environmental technologies. The LCA was conducted in accordance with the LCA principles...

  12. Fe(CO)5-catalyzed coprocessing of coal and heavy oil vacuum residue using syngas-water as a hydrogen source; Fe(CO)5 shokubai ni yoru gosei gas-mizu wo suisogen to suru sekitan-jushitsuyu no coprocessing

    Energy Technology Data Exchange (ETDEWEB)

    Hata, K.; Wada, K.; Mitsudo, T. [Kyoto University, Kyoto (Japan)

    1996-10-28

    Improvement in efficiency and profitability of hydrogenation reaction of heavy hydrocarbon resources is the most important matter to be done. In this study, coprocessing of coal and heavy oil vacuum residue was conducted using syngas-water as a hydrogen source. For the investigation of effect of the reaction temperature during the coprocessing of Wandoan coal and Arabian heavy vacuum residue using Fe(CO)5 as a catalyst, the conversion, 66.0% was obtained at 425{degree}C. For the investigation of effect of reaction time, the yield of light fractions further increased during the two stage reaction at 400{degree}C for 60 minutes and at 425{degree}C for 60 minutes. Finally, almost 100% of THF-soluble matter was obtained through the reaction using 2 mmol of Fe(CO)5 catalyst at 400{degree}C for 60 minutes, and hydrogenation of heavy oil was proceeded simultaneously. When comparing coprocessing reactions using three kinds of hydrogen sources, i.e., hydrogen, CO-water, and syngas-water, the conversion yield and oil yield obtained by using syngas-water were similar to those obtained by using hydrogen, which demonstrated the effectiveness of syngas-water. 2 refs., 2 figs., 2 tabs.

  13. Gas Sensor

    KAUST Repository

    Luebke, Ryan

    2015-01-22

    A gas sensor using a metal organic framework material can be fully integrated with related circuitry on a single substrate. In an on-chip application, the gas sensor can result in an area-efficient fully integrated gas sensor solution. In one aspect, a gas sensor can include a first gas sensing region including a first pair of electrodes, and a first gas sensitive material proximate to the first pair of electrodes, wherein the first gas sensitive material includes a first metal organic framework material.

  14. Crop Residue Biomass Effects on Agricultural Runoff

    Directory of Open Access Journals (Sweden)

    Damodhara R. Mailapalli

    2013-01-01

    Full Text Available High residue loads associated with conservation tillage and cover cropping may impede water flow in furrow irrigation and thus decrease the efficiency of water delivery and runoff water quality. In this study, the biomass residue effects on infiltration, runoff, and export of total suspended solids (TSS, dissolved organic carbon (DOC, sediment-associated carbon (TSS-C, and other undesirable constituents such as phosphate (soluble P, nitrate (, and ammonium ( in runoff water from a furrow-irrigated field were studied. Furrow irrigation experiments were conducted in 91 and 274 m long fields, in which the amount of residue in the furrows varied among four treatments. The biomass residue in the furrows increased infiltration, and this affected total load of DOC, TSS, and TSS-C. Net storage of DOC took place in the long but not in the short field because most of the applied water ran off in the short field. Increasing field length decreased TSS and TSS-C losses. Total load of , , and soluble P decreased with increasing distance from the inflow due to infiltration. The concentration and load of P increased with increasing residue biomass in furrows, but no particular trend was observed for and . Overall, the constituents in the runoff decreased with increasing surface cover and field length.

  15. Gas Hydrate Storage of Natural Gas

    Energy Technology Data Exchange (ETDEWEB)

    Rudy Rogers; John Etheridge

    2006-03-31

    Environmental and economic benefits could accrue from a safe, above-ground, natural-gas storage process allowing electric power plants to utilize natural gas for peak load demands; numerous other applications of a gas storage process exist. A laboratory study conducted in 1999 to determine the feasibility of a gas-hydrates storage process looked promising. The subsequent scale-up of the process was designed to preserve important features of the laboratory apparatus: (1) symmetry of hydrate accumulation, (2) favorable surface area to volume ratio, (3) heat exchanger surfaces serving as hydrate adsorption surfaces, (4) refrigeration system to remove heat liberated from bulk hydrate formation, (5) rapid hydrate formation in a non-stirred system, (6) hydrate self-packing, and (7) heat-exchanger/adsorption plates serving dual purposes to add or extract energy for hydrate formation or decomposition. The hydrate formation/storage/decomposition Proof-of-Concept (POC) pressure vessel and supporting equipment were designed, constructed, and tested. This final report details the design of the scaled POC gas-hydrate storage process, some comments on its fabrication and installation, checkout of the equipment, procedures for conducting the experimental tests, and the test results. The design, construction, and installation of the equipment were on budget target, as was the tests that were subsequently conducted. The budget proposed was met. The primary goal of storing 5000-scf of natural gas in the gas hydrates was exceeded in the final test, as 5289-scf of gas storage was achieved in 54.33 hours. After this 54.33-hour period, as pressure in the formation vessel declined, additional gas went into the hydrates until equilibrium pressure/temperature was reached, so that ultimately more than the 5289-scf storage was achieved. The time required to store the 5000-scf (48.1 hours of operating time) was longer than designed. The lower gas hydrate formation rate is attributed to a

  16. Quadratic residues and non-residues selected topics

    CERN Document Server

    Wright, Steve

    2016-01-01

    This book offers an account of the classical theory of quadratic residues and non-residues with the goal of using that theory as a lens through which to view the development of some of the fundamental methods employed in modern elementary, algebraic, and analytic number theory. The first three chapters present some basic facts and the history of quadratic residues and non-residues and discuss various proofs of the Law of Quadratic Reciprosity in depth, with an emphasis on the six proofs that Gauss published. The remaining seven chapters explore some interesting applications of the Law of Quadratic Reciprocity, prove some results concerning the distribution and arithmetic structure of quadratic residues and non-residues, provide a detailed proof of Dirichlet’s Class-Number Formula, and discuss the question of whether quadratic residues are randomly distributed. The text is a valuable resource for graduate and advanced undergraduate students as well as for mathematicians interested in number theory.

  17. The greenhouse gas intensity and potential biofuel production capacity of maize stover harvest in the US Midwest

    Energy Technology Data Exchange (ETDEWEB)

    Jones, Curtis D. [Department of Geographical Sciences, University of Maryland, College Park MD 20742 USA; Zhang, Xuesong [Joint Global Change Research Institute, Pacific Northwest National Laboratory and University of Maryland, College Park MD 20740 USA; Reddy, Ashwan D. [Department of Geographical Sciences, University of Maryland, College Park MD 20742 USA; Robertson, G. Philip [Great Lakes Bioenergy Research Center, Michigan State University, East Lansing MI 48824 USA; W.K. Kellogg Biological Station, Michigan State University, Hickory Corners MI 49060 USA; Department of Plant, Soil and Microbial Sciences, Michigan State University, East Lansing MI 48824 USA; Izaurralde, Roberto César [Department of Geographical Sciences, University of Maryland, College Park MD 20742 USA; Texas A& M AgriLife Research & Extension Center, Temple TX 76502 USA

    2017-08-11

    Agricultural residues are important sources of feedstock for a cellulosic biofuels industry that is being developed to reduce greenhouse gas emissions and improve energy independence. While the US Midwest has been recognized as key to providing maize stover for meeting near-term cellulosic biofuel production goals, there is uncertainty that such feedstocks can produce biofuels that meet federal cellulosic standards. Here, we conducted extensive site-level calibration of the Environmental Policy Integrated Climate (EPIC) terrestrial ecosystems model and applied the model at high spatial resolution across the US Midwest to improve estimates of the maximum production potential and greenhouse gas emissions expected from continuous maize residue-derived biofuels. A comparison of methodologies for calculating the soil carbon impacts of residue harvesting demonstrates the large impact of study duration, depth of soil considered, and inclusion of litter carbon in soil carbon change calculations on the estimated greenhouse gas intensity of maize stover-derived biofuels. Using the most representative methodology for assessing long-term residue harvesting impacts, we estimate that only 5.3 billion liters per year (bly) of ethanol, or 8.7% of the near-term US cellulosic biofuel demand, could be met under common no-till farming practices. However, appreciably more feedstock becomes available at modestly higher emissions levels, with potential for 89.0 bly of ethanol production meeting US advanced biofuel standards. Adjustments to management practices, such as adding cover crops to no-till management, will be required to produce sufficient quantities of residue meeting the greenhouse gas emission reduction standard for cellulosic biofuels. Considering the rapid increase in residue availability with modest relaxations in GHG reduction level, it is expected that management practices with modest benefits to soil carbon would allow considerable expansion of potential cellulosic

  18. Ion and mixed conducting oxides as catalysts

    NARCIS (Netherlands)

    Gellings, P.J.; Bouwmeester, Henricus J.M.

    1992-01-01

    This paper gives a survey of the catalytic properties of solid oxides which display oxygen ion or mixed (i.e. ionic + electronic) conductivity. Particular consideration is given to the oxidation-reduction reactions of gas phase components, but attention is also devoted to oxygen exchange between gas

  19. Relict gas hydrates as possible reason of gas emission from shallow permafrost at the northern part of West Siberia

    Science.gov (United States)

    Chuvilin, Evgeny; Bukhanov, Boris; Tumskoy, Vladimir; Istomin, Vladimir; Tipenko, Gennady

    2017-04-01

    Intra-permafrost gas (mostly methane) is represent a serious geological hazards during exploration and development of oil and gas fields. Special danger is posed by large methane accumulations which usually confined to sandy and silty sand horizons and overlying in the frozen strata on the depth up to 200 meters. Such methane accumulations are widely spread in a number of gas fields in the northern part of Western Siberia. According to indirect indicators this accumulations can be relic gas hydrates, that formed earlier during favorable conditions for hydrate accumulation (1, 2). Until now, they could be preserved in the frozen sediments due to geological manifestation of the self-preservation effect of gas hydrates at temperatures below zero. These gas hydrate formations, which are lying above the gas hydrate stability zone today, are in a metastable state and are very sensitive to various anthropogenic impacts. During drilling and operation of production wells in the areas where the relic of gas hydrates can occur, there are active gas emission and gas explosion, that can lead to various technical complications up to the accident. Mathematical and experimental simulations were were conducted to evaluate the possibility of existence of relic gas hydrates in the northern part of West Siberia. The results of math simulations revealed stages of geological history when the gas hydrate stability zone began virtually from the ground surface and saturated in shallow permafrost horizons. Later permafrost is not completely thaw. Experimental simulations of porous gas hydrate dissociation in frozen soils and evaluation of self-preservation manifestation of gas hydrates at negative temperatures were carried out for identification conditions for relic gas hydrates existence in permafrost of northern part of West Siberia. Sandy and silty sand sediments were used in experimental investigations. These sediments are typical of most gas-seeping (above the gas hydrate stability

  20. Distribution of 19 organochlorinated pesticides residues in ginseng ...

    African Journals Online (AJOL)

    The organochlorinated pesticides widely applied and still remains in soils, has become toxic to ginseng production in Jilin Province. In this study, 19 trace organochlorinated pesticide residues in five types of ginseng products and soil samples from four ginseng production areas were analyzed using a gas ...

  1. Pesticide Residues in Beef and Camel Meat From Slaughterhouses ...

    African Journals Online (AJOL)

    One hundred and fifty one beef (n=136) and camel (n=15) meat samples comprising mainly of adipose tissue were collected from animals slaughtered in 13 districts in Kenya for analysis of organophosphate and organochlorine pesticide residues. Gas chromatographic method (GLC) and ECD and FID was used for ...

  2. PESTICIDE RESIDUES IN THE WATER AND FISH (LAGOON ...

    African Journals Online (AJOL)

    Liquid-liquid and liquid-solid extraction technique was employed to extract pesticide residues in water and fish samples, respectively, using 1:1 (v/v) ethyl acetate/dichloromethane mixture before being analyzed by gas chromatography. The highest level of pesticide contaminations was recorded in the Chemu lagoon as ...

  3. Crop residue decomposition, residual soil organic matter and nitrogen mineralization in arable soils with contrasting textures

    NARCIS (Netherlands)

    Matus, F.J.

    1994-01-01

    To evaluate the significance of cropping, soil texture and soil structure for the decomposition of 14C- and 15N-labelled crop residues, a study was conducted in a sand and a

  4. Sharing Residual Liability

    DEFF Research Database (Denmark)

    Carbonara, Emanuela; Guerra, Alice; Parisi, Francesco

    2016-01-01

    Economic models of tort law evaluate the efficiency of liability rules in terms of care and activity levels. A liability regime is optimal when it creates incentives to maximize the value of risky activities net of accident and precaution costs. The allocation of primary and residual liability...... the virtues and limits of loss-sharing rules in generating optimal (second-best) incentives and allocations of risk. We find that loss sharing may be optimal in the presence of countervailing policy objectives, homogeneous risk avoiders, and subadditive risk, which potentially offers a valuable tool...

  5. Toxicity potential of residual ethylene oxide on fresh or frozen embryos maintained in plastic straws.

    Science.gov (United States)

    Schiewe, M C; Schmidt, P M; Pontbriand, D; Wildt, D E

    1988-01-01

    The toxic effects of residual ethylene oxide (EtO), a frequently used gas-sterilant, on embryos either frozen for long-term purposes or stored acutely for 30 min to 9 hr in a fresh condition in 0.25-ml straw containers were evaluated. In Experiment 1, fresh embryos were frozen (using conventional technology) in straws previously aerated for 0 hr to 8 mo after EtO sterilization. With the exception of the 8-mo group in which survival and quality ratings were depressed, embryo viability was not affected significantly by short-term prefreeze and post-thaw exposure to EtO residues. Experiment 2 was conducted to analyze the influence of prefreeze exposure to EtO residues on embryo development in vitro for embryos temporarily stored in previously sterilized straws aerated for different intervals. Compared to non-EtO-sterilized control straws, the development, quality, and viability of embryos exposed to EtO-treated straws were compromised (p less than 0.05) as the aeration interval decreased and the exposure interval increased. The combined results of both experiments indicate that EtO-treated straws can be used to cryopreserve gametes efficiently, but only if the aeration interval is greater than or equal to 72 hr and the prefreeze duration of exposure is less than or equal to 3 hr.

  6. Properties of residual marine fuel produced by thermolysis from polypropylene waste

    Directory of Open Access Journals (Sweden)

    Linas Miknius

    2015-06-01

    Full Text Available Thermal degradation of waste plastics with the aim of producing liquid fuel is one of the alternative solutions to landfill disposal or incineration. The paper describes thermal conversion of polypropylene waste and analysis of produced liquid fuel that would satisfy ISO 8217-2012 requirements for a residual marine fuel. Single pass batch thermolysis processes were conducted at different own vapour pressures (20-80 barg that determined process temperature, residence time of intermediates what resulted in different yields of the liquid product. Obtained products were stabilized by rectification to achieve required standard flash point. Gas chromatography and 1H NMR spectrometry show aliphatic nature of the liquid product where majority of the compounds are isoalkanes and isoalkenes. Only lightest fractions boiling up to a temperature of 72 oC have significant amount of n-pentane. Distribution of aromatic hydrocarbons is not even along the boiling range. The fractions boiling at a temperature of 128 oC and 160 oC have the highest content of monocyclic arenes – 3.16 % and 4.09 % respectively. The obtained final liquid residual product meets all but one requirements of ISO 8217-2012 for residual marine fuels.DOI: http://dx.doi.org/10.5755/j01.ms.21.2.6105

  7. Gas processing device

    International Nuclear Information System (INIS)

    Kobayashi, Yoshihiro; Seki, Eiji.

    1991-01-01

    State of electric discharge is detected based on a gas pressure in a sealed container and a discharging current flowing between both of electrodes. When electric arc discharges occur, introduction of gases to be processed is stopped and a voltage applied to both of the electrodes is interrupted. Then, when the gas pressure in the sealed container is lowered to a predetermined value, a power source voltage is applied again to both of the electrodes to recover glow discharges, and the introduction of the gas to be processed is started. With such steps, even if electric arc discharges occur, they are eliminated automatically and, accordingly, normal glow discharges can be recovered, to prevent failures of the device due to electric arc discharges. The glow discharges are recovered automatically without stopping the operation of the gas processing device, and gas injection and solidification processing can be conducted continuously and stably. (T.M.)

  8. Electrodialytic remediation of municipal solid waste incineration residues using different membranes

    DEFF Research Database (Denmark)

    Parés Viader, Raimon; Jensen, Pernille Erland; Ottosen, Lisbeth M.

    2017-01-01

    In the present work, three different commercial membrane brands were used in an identical electrodialytic cell setup and operating conditions, in order to reduce the leaching of metals and salt anions of two types of municipal solid waste incineration residues: air pollution control residues...... of a semi-dry flue-gas cleaning system and fly ashes from a plant with wet flue-gas cleaning system. The results showed a general reduction of the leaching in both residues after ED remediation. For the following elements, the leaching was found to be different after ED treatment depending on the membrane...... used, with statistical significance: • Air pollution control residues of the semi-dry flue-gas cleaning system: Cr, Cu, Ni, Pb, Zn; • Fly ashes from a plant with wet flue-gas cleaning system: Al, Ba, Cu, Ni, Zn, Cl, SO4. Final leaching values for some elements and membranes, but not the majority, were...

  9. Recycling a hydrogen rich residual stream to the power and steam plant

    Energy Technology Data Exchange (ETDEWEB)

    Martinez, P. [Instituto de Energia y Desarrollo Sustentable, CNEA, CONICET, Av. del Libertador 8250 Buenos Aires, Ciudad Autonoma de Buenos Aires (Argentina); Eliceche, A.M. [Chemical Engineering Department, Universidad Nacional del Sur, PLAPIQUI-CONICET, Camino La Carrindanga Km 7 (8000) Bahia Blanca (Argentina)

    2010-06-15

    The benefits of using a residual hydrogen rich stream as a clean combustion fuel in order to reduce Carbon dioxide emissions and cost is quantified. A residual stream containing 86% of hydrogen, coming from the top of the demethanizer column of the cryogenic separation sector of an ethylene plant, is recycled to be mixed with natural gas and burned in the boilers of the utility plant to generate high pressure steam and power. The main advantage is due to the fact that the hydrogen rich residual gas has a higher heating value and less CO{sub 2} combustion emissions than the natural gas. The residual gas flowrate to be recycled is selected optimally together with other continuous and binary operating variables. A Mixed Integer Non Linear Programming problem is formulated in GAMS to select the operating conditions to minimize life cycle CO{sub 2} emissions. (author)

  10. Bioenergy from sisal residues

    Energy Technology Data Exchange (ETDEWEB)

    Jungersen, G. [Dansk Teknologisk Inst. (Denmark); Kivaisi, A.; Rubindamayugi, M. [Univ. of Dar es Salaam (Tanzania, United Republic of)

    1998-05-01

    The main objectives of this report are: To analyse the bioenergy potential of the Tanzanian agro-industries, with special emphasis on the Sisal industry, the largest producer of agro-industrial residues in Tanzania; and to upgrade the human capacity and research potential of the Applied Microbiology Unit at the University of Dar es Salaam, in order to ensure a scientific and technological support for future operation and implementation of biogas facilities and anaerobic water treatment systems. The experimental work on sisal residues contains the following issues: Optimal reactor set-up and performance; Pre-treatment methods for treatment of fibre fraction in order to increase the methane yield; Evaluation of the requirement for nutrient addition; Evaluation of the potential for bioethanol production from sisal bulbs. The processing of sisal leaves into dry fibres (decortication) has traditionally been done by the wet processing method, which consumes considerable quantities of water and produces large quantities of waste water. The Tanzania Sisal Authority (TSA) is now developing a dry decortication method, which consumes less water and produces a waste product with 12-15% TS, which is feasible for treatment in CSTR systems (Continously Stirred Tank Reactors). (EG)

  11. Gas valves, forests and global change: a commentary on Jarvis (1976) 'The interpretation of the variations in leaf water potential and stomatal conductance found in canopies in the field'.

    Science.gov (United States)

    Beerling, David J

    2015-04-19

    Microscopic turgor-operated gas valves on leaf surfaces-stomata-facilitate gas exchange between the plant and the atmosphere, and respond to multiple environmental and endogenous cues. Collectively, stomatal activities affect everything from the productivity of forests, grasslands and crops to biophysical feedbacks between land surface vegetation and climate. In 1976, plant physiologist Paul Jarvis reported an empirical model describing stomatal responses to key environmental and plant conditions that predicted the flux of water vapour from leaves into the surrounding atmosphere. Subsequent theoretical advances, building on this earlier approach, established the current paradigm for capturing the physiological behaviour of stomata that became incorporated into sophisticated models of land carbon cycling. However, these models struggle to accurately predict observed trends in the physiological responses of Northern Hemisphere forests to recent atmospheric CO2 increases, highlighting the need for improved representation of the role of stomata in regulating forest-climate interactions. Bridging this gap between observations and theory as atmospheric CO2 rises and climate change accelerates creates challenging opportunities for the next generation of physiologists to advance planetary ecology and climate science. This commentary was written to celebrate the 350th anniversary of the journal Philosophical Transactions of the Royal Society.

  12. Sugarcane rice residue biochars and their applications

    Science.gov (United States)

    Wang, J. J.

    2014-12-01

    production, and reduced greenhouse gas emission. Overall, the conversion of sugarcane harvest residue to biochar as soil amendment improves sugarcane production for both agronomic and environmental benefits. Sugarcane residue biochar also showed the potential of other environmental use for remediation of petroleum hydrocarbons.

  13. Pesticide residues in brain tissues of dairy cattle in Lembang

    Directory of Open Access Journals (Sweden)

    Indraningsih

    2006-03-01

    Full Text Available The use of pesticides to control plant diseases may cause residual formation in crops, its byproduct and environmental. Furthermore, the use of agriculture byproduct as animal feed may cause poisoning or residual formation in animal products. The purpose of this study is to investigate of pesticide residues in brain tissues of dairy cattle in relation to animal feed as a contamination source. Samples consisted of animal feeds (19 samples of fodder and 6 samples of feed, 31 samples of sera and 25 samples of brain tissues of dairy cattle collected from Lembang, West Java. Feeds and fodders were collected from dairy farms located in Lembang. Sera were directly collected from 31 heads of Frisien Holstein (FH cattle from the same location, while brain tissues of FH cattle were collected from a local animal slaughtering house. Pesticide residues were analysed using gas chromatography (GC. Both residues of organochlorines and organophosphates were detected from brain tissues with average residue concentration OP was 22.7 ppb and OC was 5.1 ppb and a total residue was 27.8 ppb. The pesticide residues in brain tissues are new information that should be taken into consideration since the Indonesian consumed this tissues as an oval. Although pesticides residue concentration was low, pathological changes were noted microscopically from the brain tissues including extracellular vacuolisation, focal necrosis, haemorrhages, dilatation of basement membrane without cellular infiltration. Both pesticide residues were also detected in sera, where OP (9.0 ppb was higher than OC (4.9 ppb. These pesticides were also detected in animal feeds consisting fodders and feeds. Residues of OP (12.0 ppb were higher than OC (1.8 ppb in feeds, but residues of OP (16.8 ppb were lower than OC (18.7 ppb in fodders. Although, pesticide residues in sera and brain tissues were below the maximum residue limits (MRL of fat, the presence of pesticides in brain tissues should be taken

  14. Gas gangrene

    Science.gov (United States)

    Tissue infection - Clostridial; Gangrene - gas; Myonecrosis; Clostridial infection of tissues; Necrotizing soft tissue infection ... Gas gangrene is most often caused by bacteria called Clostridium perfringens. It also can be caused by ...

  15. Removal of 16 pesticide residues from strawberries by washing with tap and ozone water, ultrasonic cleaning and boiling.

    Science.gov (United States)

    Lozowicka, Bozena; Jankowska, Magdalena; Hrynko, Izabela; Kaczynski, Piotr

    2016-01-01

    The effects of washing with tap and ozone water, ultrasonic cleaning and boiling on 16 pesticide (ten fungicides and six insecticides) residue levels in raw strawberries were investigated at different processing times (1, 2 and 5 min). An analysis of these pesticides was conducted using gas chromatography with nitrogen-phosphorous and electron capture detection (GC-NPD/ECD). The processing factor (PF) for each pesticide in each processing technique was determined. Washing with ozonated water was demonstrated to be more effective (reduction from 36.1 to 75.1 %) than washing with tap water (reduction from 19.8 to 68.1 %). Boiling decreased the residues of the most compounds, with reductions ranging from 42.8 to 92.9 %. Ultrasonic cleaning lowered residues for all analysed pesticides with removal of up to 91.2 %. The data indicated that ultrasonic cleaning and boiling were the most effective treatments for the reduction of 16 pesticide residues in raw strawberries, resulting in a lower health risk exposure. Calculated PFs for alpha-cypermethrin were used to perform an acute risk assessment of dietary exposure. To investigate the relationship between the levels of 16 pesticides in strawberry samples and their physicochemical properties, a principal component analysis (PCA) was performed. Graphical abstract ᅟ.

  16. Pesticide residues in leafy vegetables and human health risk assessment in North Central agricultural areas of Chile.

    Science.gov (United States)

    Elgueta, Sebastian; Moyano, Stella; Sepúlveda, Paulina; Quiroz, Carlos; Correa, Arturo

    2017-06-01

    To investigate pesticide residue concentrations and potential human health risk, a study was conducted in 118 leafy vegetable samples collected in 2014-2015 from the North Central agricultural areas of Chile. The pesticide residues were determined using the multiresidue QuEChERS method by gas chromatography as well as high-performance liquid chromatography. The results indicated that 27% of the total samples contained pesticide residues above the maximum residue limits of each active ingredient. The maximum estimated daily intake obtained for carbon disulphide (CS 2 ), methamidophos, azoxystrobin and cypermethrin were 0.57, 0.07, 0.06 and 0.05 mg kg -1 , respectively, which was higher than their acceptable daily intake. It is concluded that inhabitants of the North Central agricultural area of Chile are not exposed to health risks through the consumption of leafy vegetables with the exception of methamidophos. Nevertheless, the high levels of methamidophos detected in leafy vegetables could be considered a potential chronic health risk.

  17. Gas-controlled dynamic vacuum insulation with gas gate

    Science.gov (United States)

    Benson, D.K.; Potter, T.F.

    1994-06-07

    Disclosed is a dynamic vacuum insulation comprising sidewalls enclosing an evacuated chamber and gas control means for releasing hydrogen gas into a chamber to increase gas molecule conduction of heat across the chamber and retrieving hydrogen gas from the chamber. The gas control means includes a metal hydride that absorbs and retains hydrogen gas at cooler temperatures and releases hydrogen gas at hotter temperatures; a hydride heating means for selectively heating the metal hydride to temperatures high enough to release hydrogen gas from the metal hydride; and gate means positioned between the metal hydride and the chamber for selectively allowing hydrogen to flow or not to flow between said metal hydride and said chamber. 25 figs.

  18. Gas separating

    Science.gov (United States)

    Gollan, Arye Z.

    1990-12-25

    Feed gas is directed tangentially along the non-skin surface of gas separation membrane modules comprising a cylindrical bundle of parallel contiguous hollow fibers supported to allow feed gas to flow from an inlet at one end of a cylindrical housing through the bores of the bundled fibers to an outlet at the other end while a component of the feed gas permeates through the fibers, each having the skin side on the outside, through a permeate outlet in the cylindrical casing.

  19. Monitoring of Pesticide Residues in Commonly Used Fruits and Vegetables in Kuwait

    OpenAIRE

    Jallow, Mustapha F. A.; Awadh, Dawood G.; Albaho, Mohammed S.; Devi, Vimala Y.; Ahmad, Nisar

    2017-01-01

    The presence of pesticide residues in primary and derived agricultural products raises serious health concerns for consumers. The aim of this study was to assess the level of pesticide residues in commonly consumed fruits and vegetables in Kuwait. A total of 150 samples of different fresh vegetables and fruits were analyzed for the presence of 34 pesticides using the quick easy cheap effective rugged and safe (QuEChERS) multi-residue extraction, followed by gas chromatography-mass spectrometr...

  20. Heating oil, distillates and residuals outlook

    International Nuclear Information System (INIS)

    Ervin, M.J.

    2004-01-01

    M.J. Ervin and Associates offers strategic planning support to the downstream petroleum industry in terms of price market monitoring, market analysis, media commentary and benchmarking of marketing operations. This presentation included graphs depicting supply and demand for heating oil distillates and residuals from the mid 1990s to 2004. It was noted that the long-term decline in residuals demand in the United States and Canada are due to environmental issues, the use of natural gas as an alternative, and the increasing complexity of refineries. Graphs depicting market impacts of refinery utilization and inventory trends showed that middle distillate production will increase at the expense of gasoline production. Middle distillates and gasoline markets will be more sensitive to supply disruptions, resulting in more frequent price spikes. Inventory trends indicate a greater reliance on product imports. The demand for heating fuel has stabilized due to the continued penetration of natural gas in eastern states and provinces. The demand for diesel fuel has growth 1.5 to 2 per cent while the demand for jet fuel has remained relatively flat and depends greatly on the growth of the gross national product (GNP). tabs., figs

  1. Modelling of the Residual Stress State in a new Type of Residual Stress Specimen

    DEFF Research Database (Denmark)

    Jakobsen, Johnny; Andreasen, Jens Henrik

    2014-01-01

    The paper presents a study on a new type residual stress specimen which is proposed as a simple way to conduct experimental validation for model predictions. A specimen comprising of a steel plate with circular hole embedded into a stack of CSM glass fibre and further infused with an epoxy resin...... forms the experimental case which is analysed. A FE model of the specimen is used for analysing the curing history and the residual stress build up. The model is validated against experimental strain data which are recorded by a Fibre Brag Grating sensor and good agreement has been achieved....

  2. Modelling of the Residual Stress State in a new Type of Residual Stress Specimen

    DEFF Research Database (Denmark)

    Jakobsen, Johnny; Andreasen, Jens Henrik

    2014-01-01

    forms the experimental case which is analysed. A FE model of the specimen is used for analysing the curing history and the residual stress build up. The model is validated against experimental strain data which are recorded by a Fibre Brag Grating sensor and good agreement has been achieved.......The paper presents a study on a new type residual stress specimen which is proposed as a simple way to conduct experimental validation for model predictions. A specimen comprising of a steel plate with circular hole embedded into a stack of CSM glass fibre and further infused with an epoxy resin...

  3. 21 CFR 880.6100 - Ethylene oxide gas aerator cabinet.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Ethylene oxide gas aerator cabinet. 880.6100... Miscellaneous Devices § 880.6100 Ethylene oxide gas aerator cabinet. (a) Identification. An ethyene oxide gas... required to remove residual ethylene oxide (ETO) from wrapped medical devices that have undergone ETO...

  4. Ruslands Gas

    OpenAIRE

    Elkjær, Jonas Bondegaard

    2008-01-01

    This paper is about Russian natural gas and the possibility for Russia to use its reserves of natural gas politically towards the European Union to obtain some political power. Russia owns 32,1 % of the world gas reserves, and The European Union is getting 50 % of its gas import from Russia. I will use John Mearsheimer’s theory ”The Tragedy of Great Power Politics” to explain how Russia can use its big reserves of gas on The European Union to get political influence. This paper is about Ru...

  5. Ruslands Gas

    OpenAIRE

    Elkjær, Jonas Bondegaard

    2008-01-01

    This paper is about Russian natural gas and the possibility for Russia to use its reserves of natural gas politically towards the European Union to obtain some political power. Russia owns 32,1 % of the world gas reserves, and The European Union is getting 50 % of its gas import from Russia. I will use John Mearsheimer’s theory ”The Tragedy of Great Power Politics” to explain how Russia can use its big reserves of gas on The European Union to get political influence.

  6. Development of gasification and melting system for energy recovery from automobile shredder residue

    International Nuclear Information System (INIS)

    Jung, Hae Young; Seo, Yong Chil; Cho, Sung Jin; Lee, Jang Su; Lee, Ki Bae; Jeong, Dae Woon; Kim, Woo Hyun; Roh, Seon Ah; Min, Tai Jin

    2010-01-01

    As one of the efforts to increase recycling rate of end of life vehicles enforcing by the governmental regulation, automobile shredder residue (ASR) was considered to treat by a thermal method with converting waste to energy. Gasification and melting experimental processes of lab (1 kg/ hour) and pilot (5 ton/ day) scale were installed. ASR collected from a domestic shredding company was experimented at a lab-scale and pilot-scale gasification and melting process which is similar to the shaft type gasification melting furnace. The characteristics of syngas, tar and residue (slag) generated from a conversion process (gasification and melting) were analyzed to provide the information to further utilize them as fuel and recyclable materials in scaled up plants. A series of experiments have been conducted with various air equivalent ratios (ERs), and syngas compositions, carbon conversion efficiency, heating value of syngas, yield and characteristics of slag were analyzed. Finally, slags generated from the process were recycled with various alternative technologies. In summary, energy conversion technology of ASR with the least production of residue by gasification and slag utilization has been developed. The main components in product gas were H 2 , CO, CH 4 and CO 2 ; and concentrations of C 2 H 4 and C 2 H 6 were less. This can be used as clean fuel gas whose heating value ranged from 2.5 to 14.0 MJ/ m 3 . Most of slag generated from the process can further be fabricated to valuable and usable products. Such combined technology would result in achieving almost zero waste release from ELVs. (author)

  7. Harnessing gas

    International Nuclear Information System (INIS)

    1998-01-01

    Nigeria produces almost two million barrels of oil a day from its oil fields in the Niger Delta area. Most of the oil comes from reservoirs containing gas, which is produced with the oil. This associated gas is separated from the oil at flow stations and more than 95 per cent of it is flared-currently a total of some two billion standard cubic feet per day (scf/d), which is estimated to be about a quarter of the gas the world flares and vents. The energy available from Nigeria's flared gas is prodigious, equivalent to one quarter of France's gas requirements. The company recognises that flaring wastes a valuable resource and is environmentally damaging. It aims to stop necessary flaring as soon as possible through a series of projects to harness or conserve this gas. Several gas gathering and conservation projects are already underway in response to emerging markets while other plans await new markets. The company is committed to reduce gas flaring as soon as is feasible to the minimum needed to maintain safe operations. But why are solutions being found only now? why has Nigeria been flaring gas for so long? These question lie at the crux of the debate about Nigeria and gas flaring and the answers, which continue to have a major impact on associated gas development today, are rooted in history, economics and geography

  8. ESTIMATION OF AMOXICILLIN RESIDUES IN COMMERCIAL MEAT AND MILK SAMPLES

    Directory of Open Access Journals (Sweden)

    Ainee Irum

    2014-08-01

    Full Text Available The present study was conducted to evaluate the extent of ß - lactam antibiotic, amoxicillin residues in market milk and meat. Samples were randomly collected from Faisalabad city, Pakistan. High Performance Liquid Chromatography (HPLC method with inflorescent detector was used to detect, identify and quantify the amoxicillin residues in milk and meat samples. The milk samples were purified by performing a protein precipitation step, followed by derivatization. To clean up tissue samples, a liquid extraction, followed by a solid-phase extraction procedure C18 (4.0X4.6mm, 5μm was performed. A 50% meat and 90% milk samples were found contaminated with residues. The residues of amoxicillin in milk were in range of 28 to 46μg/kg and in meat were 9 to 84μg/kg. All of the contaminated milk and 40 out of 50% meat samples fall in maximum residue limits.

  9. Marine Tar Residues: a Review

    OpenAIRE

    Warnock, April M.; Hagen, Scott C.; Passeri, Davina L.

    2015-01-01

    Marine tar residues originate from natural and anthropogenic oil releases into the ocean environment and are formed after liquid petroleum is transformed by weathering, sedimentation, and other processes. Tar balls, tar mats, and tar patties are common examples of marine tar residues and can range in size from millimeters in diameter (tar balls) to several meters in length and width (tar mats). These residues can remain in the ocean environment indefinitely, decomposing or becoming buried in ...

  10. Tritium conductivity and isotope effect in proton-conducting perovskites

    International Nuclear Information System (INIS)

    Mukundan, R.; Brosha, E.L.; Birdsell, S.A.; Costello, A.L.; Garzon, F.H.; Willms, R.S.

    1999-01-01

    The tritium ion conductivities of SrZr 0.9 Yb 0.1 O 2.95 and BaCe 0.9 Yb 0.1 O 2.95 have been measured by ac impedance analysis. The high tritium conductivity of these perovskites could potentially lead to their application as an electrochemical membrane for the recovery of tritium from tritiated gas streams. The conductivities of these perovskites, along with SrCe 0.95 Yb 0.05 O 2.975 , were also measured in hydrogen- and deuterium-containing atmospheres to illustrate the isotope effect. For the strontium zirconate and barium cerate samples, the impedance plot consists of two clearly resolved arcs, a bulk and a grain boundary arc, in the temperature range 50--350 C. However, for the strontium cerate sample, the clear resolution of the bulk conductivity was not possible and only the total conductivity was measurable. Thus, the isotope effect was clearly established only for the strontium zirconate and barium cerate samples. The decrease in bulk conductivity with increasing isotope mass was found to be a result of an increase in the activation energy for conduction accompanied by a decrease in the pre-exponential factor. Since the concentration of the mobile species (H+, D+, or T+) should remain relatively constant at T < 350 C, this increase in activation energy is directly attributable to the increased activation energy for the isotope mobility

  11. Stabilization of APC residues from waste incineration with ferrous sulfate on a semi-industrial scale

    DEFF Research Database (Denmark)

    Lundtorp, Kasper; Jensen, Dorthe Lærke; Christensen, Thomas Højlund

    2002-01-01

    A stabilization method for air pollution control (APC) residues from municipal solid waste incineration (MSWI) involving mixing of the residue with water and FeSO4 has been demonstrated on a semi-industrial scale on three types of APC residues: a semidy (SD) APC residue, a fly ash (FA), and an FA...... mixed with sludge (FAS) from a wet flue gas cleaning system. The process was performed in batches of 165-175 kg residue. It generates a wastewater that is highly saline but has a low content of heavy metals such as Cd, Cr, and Pb. The stabilized and raw residues have been subject to a range of leaching...... tests: the batch leacing test, the pH-static leaching test, the availability test, and the column test. These tests showed that the stabilized residues have remarkably improved leaching properties, especially with respect to Pb but also with respect to Cd, Cu, and Zn. The release of Pb was reduced...

  12. Comparison of biogas production from rapeseed and wheat residues in compound with cattle manure

    Directory of Open Access Journals (Sweden)

    M Safari

    2016-09-01

    Full Text Available Introduction Seventy million tons of agricultural crops are produced from 18 million hectares of agricultural lands in Iran every year. Since 80% of the crops (wt. basis ends up as residues, therefore, about 50 million tons of crop residues are generated annually the majority of which is burnt on field leading to vast emissions of greenhouse gases (GHG due to the incomplete combustion process. These residues could potentially be transformed into heat energy directly by adopting a burning process or indirectly by first transforming them into secondary fuel as hydrogen, bio-methane, methanol or ethanol. Materials and Methods The present study was conducted using, wheat and rapeseed straws dried at ambient temperature co-digested with fresh cow dung while the total solid content and detention time were kept constant. To conduct the Anaerobic Digestion (AD experiments, cylinder reactors (13 L were constructed and placed in a water bath equipped with a heater and sensor to maintain the temperature at 35±2 oC. The biogas produced in the digester was investigated by measuring the displacement of the water in a measuring tube connected to the reactor. Gas samples were obtained from the sampling port and were analyzed gas chromatograph. The temperature for detector, injector and oven were 170, 110 and 50 oC respectively. Before the test, the first CH4 and CO2 net gases, peaks corresponding percentage was determined with respect to the retention time of the area. Then sample was compared with standard gas and samples gas percentage was determined. The residues were mechanically pretreated using a mill in order to increase the availability of the biomass to enzymes. After the pre-treatment, the material (<2 mm was mixed with a different proportion of fresh cow dung, Initial Total Solids (TS content in the reactor was adjusted at 9%. Factors such as PH, Volatile Solids (VS were determined by the standard method. Results and Discussion A decrease in the

  13. Phytotoxicity and groundwater impacts of leaching from thermal treatment residues in roadways.

    Science.gov (United States)

    Phoungthong, Khamphe; Shao, Li-Ming; He, Pin-Jing; Zhang, Hua

    2018-01-01

    The use of coal fly ash (CFA), municipal solid waste incinerator bottom ash (MSWIBA) and flue gas desulfurization residue (FGDR) in road construction has become very common owing to its economical advantages. However, these residues may contain toxic constituents that pose an environmental risk if they leach out and flow through the soil, surface water and groundwater. Therefore, it is necessary to assess the ecotoxicity and groundwater impact of these residues before decisions can be made regarding their utilization for road construction. In this study, the physico-chemical characteristics, leaching and phytotoxicity of these residues were investigated. Specifically, multivariate analyses were used to evaluate the contributions of the leaching constituents of the CFA, MSWIBA and FGDR leachates to the germination index of wheat seeds. B, Ba, Cr, Cu, Fe and Pb were found to be more toxic to the wheat seeds than the other heavy metals. Furthermore, the leached concentrations of the constituents from the CFA, MSWIBA and FGDR were below the regulatory threshold limits of the Chinese identification standard for hazardous wastes. Analyses conducted using a numerical groundwater model (WiscLEACH) indicated that the predicted field concentrations of metals from the CFA, MSWIBA and FGDR increased with time up to about 30years at the point of compliance, then decreased with time and distance. Overall, this study demonstrated that the risks resulting from MSWIBA, CFA and FGDR leaching could be assessed before its utilization for road construction, providing crucial information for the adoption of these alternative materials. Copyright © 2016. Published by Elsevier B.V.

  14. Internal residual strain mapping in carburized chrome molybdenum steel after quenching by neutron strain scanning

    International Nuclear Information System (INIS)

    Sakaida, Yoshihisa; Serizawa, Takanobu; Manzanka, Michiya

    2011-01-01

    A hollow circular cylinder specimen with an annular U-notch of chrome molybdenum steel with 0.20 mass% C (SCM420) was carburized in carrier gas and quenched in oil bath. In order to determine the case depth, the specimen was cut off and carbon content and Vickers hardness gradients were measured experimentally near the carburized surface. The residual strain mapping in the interior of carburized cylinder was conducted nondestructively by neutron strain scanning. In this study, the neutron diffraction from Fe-211 plane was used for strain scanning. The neutron wavelength was tuned to 0.1654nm so that diffraction angle became about 90deg. Radial, hoop and axial residual strains were measured by scanning diffracting volume along the axial direction of cylinder specimen. Each residual strain was calculated from lattice spacing change. Unstressed lattice spacing was determined experimentally using reference coupon specimens that were cut from the interior of same carburized cylinder. As a result, the diffraction peak width at half height, FWHM, near the carburized surface was about 3.7 times wider than that of coupon specimens. On the other hand, the most peak widths in the interior equaled to that of coupon specimens. Peak width broadened slightly as the diffracting volume approached the carburized case layer. From the center to the quarter of cylinder specimen, the hoop and axial strains were tensile, and the radial one was compressive in the interior. From the quarter to the edge of the cylinder specimen, the hoop tensile strain increased, radial and axial strains changed to tensile and compressive, respectively. Therefore, the interior of the cylinder specimen was found to be deformed elastically to balance the existence of compressive residual stresses in the carburized case layer. (author)

  15. Experience with unconventional gas turbine fuels

    Energy Technology Data Exchange (ETDEWEB)

    Mukherjee, D.K. [ABB Power Generation Ltd., Baden (Switzerland)

    1996-12-31

    Low grade fuels such as Blast Furnace Gas, biomass, residual oil, coke, and coal - if used in conjunction with appropriate combustion, gasification, and clean-up processes and in combination with a gas turbine combined cycle -offer attractive and environmentally sound power generation. Recently, the Bao Shan Iron and Steel Company in Shanghai placed an order with Kawasaki Heavy Industries, Japan, to supply a combined-cycle power plant. The plant is to employ ABB`s GT 11N2 with a combustor modified to burn blast furnace gas. Recent tests in Shanghai and at Kawasaki Steel, Japan, have confirmed the burner design. The same basic combustor concept can also be used for the low BTU gas derived from airblown gasification processes. ABB is also participating in the API project: A refinery-residual gasification combined-cycle plant in Italy. The GT 13E2 gas turbine employees MBTU EV burners that have been successfully tested under full operating conditions. These burners can also handle the MBTU gas produced in oxygenblown coal gasification processes. ABB`s vast experience in burning blast furnace gas (21 plants built during the 1950s and 1960s), residuals, crude, and coal in various gas turbine applications is an important asset for building such power plants. This presentation discusses some of the experience gained in such plants. (orig.) 6 refs.

  16. Evaluation of residue-residue contact predictions in CASP9

    KAUST Repository

    Monastyrskyy, Bohdan

    2011-01-01

    This work presents the results of the assessment of the intramolecular residue-residue contact predictions submitted to CASP9. The methodology for the assessment does not differ from that used in previous CASPs, with two basic evaluation measures being the precision in recognizing contacts and the difference between the distribution of distances in the subset of predicted contact pairs versus all pairs of residues in the structure. The emphasis is placed on the prediction of long-range contacts (i.e., contacts between residues separated by at least 24 residues along sequence) in target proteins that cannot be easily modeled by homology. Although there is considerable activity in the field, the current analysis reports no discernable progress since CASP8.

  17. [Residues of organochlorine compounds in plant drugs. 1. Gas chromatographic determination of residues of organochlorine insecticides].

    Science.gov (United States)

    Benecke, R; Thieme, H; Brotka, J

    1986-02-01

    A method for the identification and determination of HCH-and DDT-isomers and their respective metabolites in vegetable drugs is presented. The plant material is extracted with hexane in a Soxhlet apparatus in the presence of silicagel and sodium sulfate. For removing interfering endogenous plant constituents a Celite oleum column cleanup and usually and acetonitrile partitioning to follow are necessary. A mixed stationary phase OV-17/QF-1 has proved effective for the gc separation on packed columns. 3H-ECD is used for detection. For the quantitative determination by using an external standard the peak height measurement is recommended. Recoveries of all insecticides were in the order of 70-105% with coefficients of variation between 6 and 20%. To ensure the results the alkaline treatment and oxidation of extracts are proposed.

  18. Determining the Release of Radionuclides from Tank 18F Waste Residual Solids: FY2016 Report

    Energy Technology Data Exchange (ETDEWEB)

    King, William D. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Hobbs, David T. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2016-08-12

    Pore water leaching studies were conducted on actual Savannah River Site (SRS) Tank 18F residual waste solids to support Liquid Waste tank closure efforts. A test methodology was developed during previous simulant testing to produce slurries of tank residual solids and grout-representative solids in grout pore water solutions (based on SRS groundwater compositions) with pH and Eh values expected during the aging of the closed waste tank. The target conditions are provided below where the initial pore water has a reducing potential and a relatively high pH (Reducing Region II). The pore water is expected to become increasingly oxidizing with time (Oxidizing Region II) and during the latter stages of aging (Oxidizing Region III) the pH is expected to decrease. For the reducing case, tests were conducted with both unwashed and washed Tank 18F residual solids. For the oxidizing cases (Oxidizing Regions II and III), all samples were washed with simulated grout pore water solutions prior to testing, since it is expected that these conditions will occur after considerable pore water solution has passed through the system. For the reducing case, separate tests were conducted with representative ground grout solids and with calcium carbonate reagent, which is the grout phase believed to be controlling the pH. Ferrous sulfide (FeS) solids were also added to the reducing samples to lower the slurry Eh value. Calcium carbonate solids were used as the grout-representative solid phase for each of the oxidizing cases. Air purge-gas with and without CO2 removed was transferred through the oxidizing test samples and nitrogen purge-gas was transferred through the reducing test samples during leach testing. The target pH values were achieved to within 0.5 pH units for all samples. Leaching studies were conducted over an Eh range of approximately 0.7 V. However, the highest and lowest Eh values achieved of ~+0.5 V and ~-0.2 V were

  19. PENETAPAN RESIDU DAN PERKIRAAN PENETAPAN BATAS MAKSIMUM RESIDU (BMR ORGANOKLORIN PADA SIMPLISIA

    Directory of Open Access Journals (Sweden)

    Ani Isnawati

    2012-10-01

    Full Text Available Penggunaaan bahan obat tradisional (simplisia untuk skala industri dan peningkatan produksi tanaman obat dalam skala besar menjadi tidak ekonomis tanpa pestisida. Disatu sisi penggunaan pestisida dapat menguntungkan yaitu menyebabkan toksis pada hama namun disisi lain toksisitas dapat terjadi juga pada manusia, sehingga residu pestisida dalam tanaman obat yang dikonsumsi dalam jangka panjang akan merugikan kesehatan. Batas maksimum Residu (BMR pestisida dalam simplisia baik di Indonesia maupun di negara lain belum ditetapkan. Sehingga untuk itu untuk mengetahui adanya residu pestisida jenis organoklorin yang telah dilarang penggunaannya melalui Permentan No.434.1/kpts/TP.270/7/2001 dan untuk mengetahui batas keamanannya, maka perlu dilakukan penetapan residu organoklorin dalam simplisia dan menetapkan batas keamanan berdasarkan perhitungan secara teoritis. Pengujian residu dilakukan terhadap golongan pestisida organoklorin pada 4 jenis simplisia (daun wungu (Graptophyllum pictum (L Grifl, daun sambiloto Andrographis paniculata Ness, herba pegagan (Centella  asiatica (L Urban, daun tempuyung (Sonchus arvensis (L yang berasal dari 3 lokasi penanaman, yaitu : perkebunan Tanaman Obat Manako (Jawa Barat, Balai Penelitian Tanaman Obat Tawangmangu (BPTO di Jawa Tengah dan Perkebunan Tanaman Obat Purwodadi (Jawa Timur. Pemeriksaan residu pestisida organoklorin menggunakan kromatografi gas dan perhitungan batas keamanan dihitung dengan adanya nilai ADI (Acceptable daily intake yang telah ditetapkan bersama antara JAO dan WHO serta perkiraan banyaknya konsumsi simplisia. Hasil Pengujian residu pestisida organoklorin diperoleh bahwa simplisia daun Wungu (Tawangmangu mengandung residu lindan dengan kadar 0,24 mg/kg, pegagan (Purwodadi, mengandung lindan 0,36 mg/kg dan aldrin 0,31 mg/kg serta pegagan (Manako mengandung heptaklor 0,15 mg/kg dan op-DDE 0,11 mg/kg. Adapun penghitungan BMR heptaklor dan lindan secara teoritis dengan asumsi rata

  20. Crystal fields and conduction electrons in praseodymium

    DEFF Research Database (Denmark)

    Clausen, K.N.; Aagaard Sørensen, S.; McEwen, K.A.

    1995-01-01

    The interactions between the crystal-field excitations, the phonons and the conduction electrons in Pr have been studied further. The low-energy satellites to the crystal-field excitations, which are believed to be associated with propagating paramagnon modes in the conduction-electron gas, appear...

  1. An Apparatus to Measure Thermal Conductivity of Spray-On Foam Insulation

    Science.gov (United States)

    Barrios, M.; Sciver, S. W. Van

    2010-04-01

    A guarded-hot-plate apparatus has been developed to measure the thermal conductivity of various spray-on foam insulations (SOFI) at temperatures ranging from 20-300 K. The apparatus is designed to accept 222 mm (8.75″) diameter, 25.4 mm (1″) thick insulation samples, although different thicknesses can be accommodated. The apparatus is cooled with a two stage, pulse tube cryocooler, and the temperature is controlled with thin film etched foil heaters. This system allows thermal conductivity measurements to be made at low delta-T (ΔTheat flow axially through the sample. A gas handling system allows testing with different residual gases and pressures. To check for potential systematic errors, a finite element analysis was performed to examine temperature distribution and heat flow in the experimental chamber.

  2. Digestibilidade in vitro/gás de volumosos exclusivos ou combinados avaliados pelo resíduo remanescente da digestão da matéria seca e produção de gás Evaluation of the in vitro/gas digestibility of several mixtures of roughages by digestion residue of dry matter and gas production

    Directory of Open Access Journals (Sweden)

    Fábio Prudêncio de Campos

    2001-10-01

    Full Text Available Foi avaliada a digestibilidade in vitro/gás da matéria seca (MS de quatro volumosos, exclusivos e suas combinações, na proporção de 50% na MS. Foram incubados 100 mg de amostra por tratamento, em triplicatas, em 48 h de digestão. As digestibilidades da MS e a produção de gás foram: cana-de-açúcar = 60,6%, 17,3 mL; cana-de-açúcar + silagem de milho = 63,9%, 19,6 mL; cana-de-açúcar + capim-elefante com 60 dias = 60,5%, 16,9 mL; cana-de-açúcar + capim-elefante com 180 dias = 48,6%, 14,1 mL; silagem de milho = 66,3%; silagem de milho + capim-elefante com 60 dias = 62,1%, 16,7 mL; silagem de milho + capim-elefante com 180 dias = 52,7%, 15,8 mL; capim-elefante com 60 dias = 61,5%, 16,9 mL; capim-elefante com 180 dias = 34,6%, 11,7 mL. Constatou-se que a combinação de volumosos, em alguns casos, pode diminuir a digestibilidade da MS dos volumosos de melhor qualidade.The in vitro/gas dry matter (DM digestibility of four roughages, mixed or not, in proportion of 50% in the DM were evaluated. Samples of 100 mg by treatment, in triplicate, in 48 h of digestion were incubated. The DM digestibilities and gas production were: sugar cane = 60.6%, 17.3 mL; sugar cane + corn silage = 63.9%, 19.6 mL; sugar cane + elephantgrass of 60 days = 60.5%, 16.9 mL; sugar cane + elephantgrass of 180 days = 48.6%, 14.1 mL; corn silage = 66.3%, 19.4 mL; corn silage + elephantgrass of 60 days = 62.1%, 16.7 mL; corn silage + elephantgrass of 180 days = 52.7%, 15.8 mL; elephantgrass of 60 days = 61.5%, 16.9 mL; elephantgrass of 180 days = 34.6%, 11.7 mL. It was verified that the association of these roughages can, in some cases, reduce the DM digestibility of those roughages of better quality.

  3. Tip-filter tests on paraffin removal from Luetzkendorf Paraffingatsch and Zeitz separator residue hydrogenated in a small unit

    Energy Technology Data Exchange (ETDEWEB)

    Engel

    1943-04-21

    By the propane process, deparaffining tests were conducted on hydrogenated products made from Luetzkendorf and Zeitz residues. A table provided information as to raw materials, hydrogenation temperature, catalyst, pressure, input, and gas used. The report stated that all materials were deparaffined by heating each 300 g, in which 1.5 g filtering agent A was dissolved together with 600 g propane, to 70/sup 0/C in the tip-filter. Then the mixture was cooled to -40/sup 0/C, filtered under 0.2 atmospheres of nitrogen, and 1 to 3 g removed for a paraffin test. The rest of the paraffin was immediately mixed with 600 g propane. This was stirred for 10 minutes at -40/sup 0/C, and filtered again under 0.2 atmospheres nitrogen. All products tested gave good results in the tip-filter. Properties of products resulting from the deparaffination were discussed. These included specific gravity, paraffin melting points and how hydrogenation temperatures affected specific gravity. Tables attached gave information resulting from processes run on the residues. Luetzkendorf Paraffingatsch (paraffin sludge from Fischer--Tropsch synthesis) gave 44.6% to 49% (by weight) paraffin when hydrogenated at temperatures between 14.5 and 20.5 millivolts; at higher temperatures, the specific gravity of the oil fell off increasingly strongly and that of the paraffin not so strongly. Hydrogenation of Zeitz residue didn't seem to change the properties of its paraffins very greatly, but the paraffin content was increased a bit (from 43.5% to more than 48%). Hydrogenating Zeitz residue with higher throughput and less gas injected gave slightly lower yield of paraffin, and the specific gravity of the paraffin was lower, whereas that of the oil was higher.

  4. GAS BEARING

    Science.gov (United States)

    Skarstrom, C.W.

    1960-09-01

    A gas lubricated bearing for a rotating shaft is described. The assembly comprises a stationary collar having an annular member resiliently supported thereon. The collar and annular member are provided with cooperating gas passages arranged for admission of pressurized gas which supports and lubricates a bearing block fixed to the rotatable shaft. The resilient means for the annular member support the latter against movement away from the bearing block when the assembly is in operation.

  5. Requirements for gas quality and gas appliances

    NARCIS (Netherlands)

    Levinsky, Howard; Gersen, Sander; Kiewiet, Bert

    2015-01-01

    Introduction The gas transmission network in the Netherlands transports two different qualities of gas, low-calorific gas known as G-gas or L-gas and, high calorific gas (H-gas). These two gas qualities are transported in separate networks, and are connected by means of five blending and conversion

  6. Landfilling of waste incineration residues

    DEFF Research Database (Denmark)

    Christensen, Thomas Højlund; Astrup, Thomas; Cai, Zuansi

    2002-01-01

    Residues from waste incineration are bottom ashes and air-pollution-control (APC) residues including fly ashes. The leaching of heavy metals and salts from the ashes is substantial and a wide spectrum of leaching tests and corresponding criteria have been introduced to regulate the landfilling...

  7. Lithic Residue Survival and Characterisation at Star Carr: a burial experiment

    Directory of Open Access Journals (Sweden)

    Shannon Croft

    2016-09-01

    Full Text Available A modern burial experiment was devised to test microscopic residue survival in acidic peat and slightly acidic clay soils at the Early Mesolithic site of Star Carr (North Yorkshire, UK, and at nearby control location. The experiment addresses concerns regarding the applicability of residue analysis in varied burial environments, and particularly in highly acidic archaeological conditions. Flint flakes (n= 78, including blank controls were used on twelve plant, animal, and mineral materials to create residues and then buried. The residues were examined 1 month and 11 months after burial. An unburied reference collection containing the same twelve residue types in a fresh state was compared to the buried residues to assess diagenesis. The residue types that survived across all burial conditions and time intervals were: softwood tissue, tree resin, bird feathers, squirrel hair, and red ochre. During microscopic analysis, it became clear that many residues lack diagnostic traits, and thus an assessment of the extent to which each residue can be identified was conducted. The degree to which residues were able to be identified was further investigated with a variable pressure scanning electron microscope (SEM. SEM images of the reference residues were compared to the reflected VLM micrographs of the same residues, which improved characterisation in some cases. Residues were grouped into three categories (diagnostic, distinctive, and non-distinctive within a visual characterisation guide. Our in situ microscopic analyses indicated that few residue types have diagnostic traits that allow them to be identified unambiguously, and thus further characterisation techniques are often required.

  8. Gas separating

    Science.gov (United States)

    Gollan, A.

    1988-03-29

    Feed gas is directed tangentially along the non-skin surface of gas separation membrane modules comprising a cylindrical bundle of parallel contiguous hollow fibers supported to allow feed gas to flow from an inlet at one end of a cylindrical housing through the bores of the bundled fibers to an outlet at the other end while a component of the feed gas permeates through the fibers, each having the skin side on the outside, through a permeate outlet in the cylindrical casing. 3 figs.

  9. Low Conductivity Thermal Barrier Coatings

    Science.gov (United States)

    Zhu, Dong-Ming

    2005-01-01

    Thermal barrier coatings will be more aggressively designed to protect gas turbine engine hot-section components in order to meet future engine higher fuel efficiency and lower emission goals. In this presentation, thermal barrier coating development considerations and requirements will be discussed. An experimental approach is established to monitor in real time the thermal conductivity of the coating systems subjected to high-heat-flux, steady-state and cyclic temperature gradients. Advanced low conductivity thermal barrier coatings have also been developed using a multi-component defect clustering approach, and shown to have improved thermal stability. The durability and erosion resistance of low conductivity thermal barrier coatings have been improved utilizing advanced coating architecture design, composition optimization, in conjunction with more sophisticated modeling and design tools.

  10. Statistical inference on residual life

    CERN Document Server

    Jeong, Jong-Hyeon

    2014-01-01

    This is a monograph on the concept of residual life, which is an alternative summary measure of time-to-event data, or survival data. The mean residual life has been used for many years under the name of life expectancy, so it is a natural concept for summarizing survival or reliability data. It is also more interpretable than the popular hazard function, especially for communications between patients and physicians regarding the efficacy of a new drug in the medical field. This book reviews existing statistical methods to infer the residual life distribution. The review and comparison includes existing inference methods for mean and median, or quantile, residual life analysis through medical data examples. The concept of the residual life is also extended to competing risks analysis. The targeted audience includes biostatisticians, graduate students, and PhD (bio)statisticians. Knowledge in survival analysis at an introductory graduate level is advisable prior to reading this book.

  11. Feasibility study for anaerobic digestion of agricultural crop residues. Dynatech report No. 1935

    Energy Technology Data Exchange (ETDEWEB)

    Ashare, E.; Buivid, M. G.; Wilson, E. H.

    1979-07-31

    The objective of this study was to provide cost estimates for the pretreatment/digestion of crop residues to fuel gas. A review of agricultural statistics indicated that the crop residues wheat straw, corn stover, and rice straw are available in sufficient quantity to provide meaningful supplies of gas. Engineering economic analyses were performed for digestion of wheat straw, corn stover, and rice straw for small farm-, cooperative-, and industrial scales. The small farm scale processed the residue from an average size US farm (400 acres), and the other sizes were two and three orders of magnitude greater. The results of the analyses indicate that the production of fuel gas from these residues is, at best, economically marginal, unless a credit can be obtained for digester effluent. The use of pretreatment can double the fuel gas output but will not be economically justifiable unless low chemical requirements or low cost chemicals can be utilized. Additional development is necessary in this area. Use of low cost hole-in-the-ground batch digestion results in improved economics for the small farm size digestion system, but not for the cooperative and industrial size systems. Recommendations arising from this study are continued development of autohydrolysis and chemical pretreatment of agricultural crop residues to improve fuel gas yields in an economically feasible manner; development of a low cost controlled landfill batch digestion process for small farm applications; and determination of crop residue digestion by-product values for fertilizer and refeed.

  12. Automatic prediction of catalytic residues by modeling residue structural neighborhood

    Directory of Open Access Journals (Sweden)

    Passerini Andrea

    2010-03-01

    Full Text Available Abstract Background Prediction of catalytic residues is a major step in characterizing the function of enzymes. In its simpler formulation, the problem can be cast into a binary classification task at the residue level, by predicting whether the residue is directly involved in the catalytic process. The task is quite hard also when structural information is available, due to the rather wide range of roles a functional residue can play and to the large imbalance between the number of catalytic and non-catalytic residues. Results We developed an effective representation of structural information by modeling spherical regions around candidate residues, and extracting statistics on the properties of their content such as physico-chemical properties, atomic density, flexibility, presence of water molecules. We trained an SVM classifier combining our features with sequence-based information and previously developed 3D features, and compared its performance with the most recent state-of-the-art approaches on different benchmark datasets. We further analyzed the discriminant power of the information provided by the presence of heterogens in the residue neighborhood. Conclusions Our structure-based method achieves consistent improvements on all tested datasets over both sequence-based and structure-based state-of-the-art approaches. Structural neighborhood information is shown to be responsible for such results, and predicting the presence of nearby heterogens seems to be a promising direction for further improvements.

  13. Biodesulphurization Within Natural Gas in Oil and Gas Field

    Directory of Open Access Journals (Sweden)

    Sri Rahayu

    2010-10-01

    Full Text Available The presence of sulphur compounds in natural gas can interfere to the quality of natural gas. The decline of combustion gas capacity, metal instrument corrosion in gas piping, and the environmental pollution from gas emission can affect by their presence. Bio-filter is one of the methods  that selected to reduce sulphur content in natural gas. A lab scale study of hydrogen sulphide reduction in natural gas had conducted in oil and gas field using bio-filter method. The bio-filter system (±1 L volume contains an active carbon and thiosulphide medium as a substrate, Thiobacillus thioparus as a single culture of sulphur bacteria, and Thiobacillus thioparus with sludge as a mixed culture of sulphur bacteria. The study of hydrogen sulphide reduction was conducted with continuous flow line process. The gas flow rate approximately 1.5 L/min with a fluctuate presence of Hydrogen sulphide (approximately 40 - 70 mg/L. The bio-filter system contains active carbon, thiosulphide medium, and single culture of T. thioparus appear as a good filter for hydrogen sulphide reduction. During 24 hours, the hydrogen sulphide reduction obtains 93% to 16%. When  culture media added, the hydrogen sulphide reduction will increase almost 60% and then the reduction decrease to 4% after 20 hours. It is concluded that the bio-filter have potential to develop for sulphur reduction in natural gas.

  14. Successive monitoring surveys of selected banned and restricted pesticide residues in vegetables from the northwest region of China from 2011 to 2013.

    Science.gov (United States)

    Yu, Yan; Hu, Senke; Yang, Yuxuan; Zhao, Xiaodan; Xue, Jianjun; Zhang, Jinghua; Gao, Song; Yang, Aimin

    2017-08-02

    A wide range of pesticides is applied for crop protection in vegetable cultivation in China. Regulation of pesticide maximum residue limits (MRLs) in vegetables is established but not fully enforced. And pesticide residues in vegetables were not well monitored. This study conducted the monitoring surveys from 2011 to 2013 to investigate the pesticides in vegetables in the northwest region of China. A multi-residue gas chromatography/mass spectrometry method (GC/MS) was used in determination of pesticides in vegetable samples. The χ 2 test was used to compare the concentration of pesticide residues. A total of 32 pesticide residues were detected in 518 samples from 20 types of vegetables in this study. 7.7% of the detected pesticide residues exceeded the MRLs. The percentages of residues that exceeded the MRLs for leafy, melon and fruit, and root vegetables were 11.2%, 5.1%, and 1.6%, respectively. There was no seasonal difference in the proportion of samples that exceeded the MRLs in different vegetables. A total of 84.3% (27/32) pesticides were detected at concentrations that exceeded MRLs. And of the 27 pesticides that exceeded the MRLs, 11 (40.7%) were banned for use in agriculture. The most frequently detected pesticides were Malathion (9.4%), Dichlorvos (8.7%), and Dimethoate (8.1%). The observed high rate of pesticides detected and high incidence of pesticide detection exceeding their MRLs in the commonly consumed vegetables indicated that the Good Agricultural Practices (GAP) may not be well followed. The management of pesticide use and control should be improved. Well-developed training programs should be initiated to improve pesticide application knowledge for farmers.

  15. Successive monitoring surveys of selected banned and restricted pesticide residues in vegetables from the northwest region of China from 2011 to 2013

    Directory of Open Access Journals (Sweden)

    Yan Yu

    2017-08-01

    Full Text Available Abstract Background A wide range of pesticides is applied for crop protection in vegetable cultivation in China. Regulation of pesticide maximum residue limits (MRLs in vegetables is established but not fully enforced. And pesticide residues in vegetables were not well monitored. This study conducted the monitoring surveys from 2011 to 2013 to investigate the pesticides in vegetables in the northwest region of China. Methods A multi-residue gas chromatography/mass spectrometry method (GC/MS was used in determination of pesticides in vegetable samples. The χ2 test was used to compare the concentration of pesticide residues. Results A total of 32 pesticide residues were detected in 518 samples from 20 types of vegetables in this study. 7.7% of the detected pesticide residues exceeded the MRLs. The percentages of residues that exceeded the MRLs for leafy, melon and fruit, and root vegetables were 11.2%, 5.1%, and 1.6%, respectively. There was no seasonal difference in the proportion of samples that exceeded the MRLs in different vegetables. A total of 84.3% (27/32 pesticides were detected at concentrations that exceeded MRLs. And of the 27 pesticides that exceeded the MRLs, 11 (40.7% were banned for use in agriculture. The most frequently detected pesticides were Malathion (9.4%, Dichlorvos (8.7%, and Dimethoate (8.1%. Conclusion The observed high rate of pesticides detected and high incidence of pesticide detection exceeding their MRLs in the commonly consumed vegetables indicated that the Good Agricultural Practices (GAP may not be well followed. The management of pesticide use and control should be improved. Well-developed training programs should be initiated to improve pesticide application knowledge for farmers.

  16. How can French agriculture contribute to reducing greenhouse gas emissions? Abatement potential and cost of ten technical measures. Summary of the study report conducted by INRA on behalf of ADEME, MAAF and MEDDE

    International Nuclear Information System (INIS)

    Pellerin, Sylvain; Bamiere, Laure; Savini, Isabelle; Pardon, Lenaic; Chemineau, Philippe; Schmitt, Bertrand; Angers, D.; Beline, F.; Benoit, M.; Butault, J.P.; Chenu, C.; Colnenne-David, C.; De Cara, S.; Delame, N.; Doreau, M.; Dupraz, P.; Faverdin, P.; Garcia-Launay, F.; Hassouna, M.; Henault, C.; Jeuffroy, M.H.; Klumpp, K.; Metay, A.; Moran, D.; Recous, S.; Samson, E.

    2013-07-01

    The agricultural industry produces nearly one-fifth of France's greenhouse gas emissions (GHGs). But it also has a strong potential for carbon sequestration. ADEME and the French Ministries for Agriculture and the Environment asked INRA to carry out a study on French agriculture to develop and analyse various measures on farming practices that could boost carbon sequestration and minimise GHGs. There are four key ways agriculture can be a part of the solution of reducing GHG emissions: Lower emissions of nitrous oxide (N 2 O, a powerful GHG released during fertiliser processing or manure spreading) and methane (CH 4 , a GHG that comes mostly from livestock); Increase carbon sequestration in soil and biomass; Reduce energy use and produce energy from biomass (agro-fuels or biogas, which lower emissions as substitutes for fossil fuels); Produce materials from biomass. The study specified that eligible measures be based on farming practices that farmers have a say in changing, lead to reductions affecting commercial farms at least in part, do not require major changes to the production system and do not reduce yields by more than 10%. For each of the chosen measures, the study analysed the potential emissions reductions and gains versus tradeoffs for farmers if implemented. The ten measures are centered around nitrogen management (nitrogen fertilizer, pulses), practices that help increase carbon sequestration in soil and biomass (fallow land, agro-forestry, intermediate crops and inter-cropping, pasture management), animal feed (rations that minimise nitrogen excretion or methane production) and the production and consumption of energy by farming (methanation, fossil fuel economies). The study highlights a strong potential for the agricultural sector to reduce emissions through these measures. According to the experts' calculations, if all ten were adopted, France could achieve a cumulative annual reduction of 32 million tons of CO 2 equivalent by 2030. However, only

  17. Prediction of the Effective Thermal Conductivity of Powder Insulation

    Science.gov (United States)

    Jin, Lingxue; Park, Jiho; Lee, Cheonkyu; Jeong, Sangkwon

    The powder insulation method is widely used in structural and cryogenic systems such as transportation and storage tanks of cryogenic fluids. The powder insulation layer is constructed by small particle powder with light weight and some residual gas with high porosity. So far, many experiments have been carried out to test the thermal performance of various kinds of powder, including expanded perlite, glass microspheres, expanded polystyrene (EPS). However, it is still difficult to predict the thermal performance of powder insulation by calculation due to the complicated geometries, including various particle shapes, wide powder diameter distribution, and various pore sizes. In this paper, the effective thermal conductivity of powder insulation has been predicted based on an effective thermal conductivity calculationmodel of porous packed beds. The calculation methodology was applied to the insulation system with expanded perlite, glass microspheres and EPS beads at cryogenic temperature and various vacuum pressures. The calculation results were compared with previous experimental data. Moreover, additional tests were carried out at cryogenic temperature in this research. The fitting equations of the deformation factor of the area-contact model are presented for various powders. The calculation results show agood agreement with the experimental results.

  18. Reactivity of Athabasca residue and of its SARA fractions during residue hydroconversion

    Energy Technology Data Exchange (ETDEWEB)

    Verstraete, J.; Danial-Fortain, P.; Gauthier, T.; Merdrignac, I. [IFP-Lyon, Vermaison (France); Budzinski, H. [Bordeaux Univ. (France). ISM-LPTC, UMR CNRS

    2009-07-01

    Residue conversion processes are becoming increasingly important because of the declining market for residual fuel oil and a greater demand for middle distillates. Ebullated-bed hydroconversion is a commercially proven technology for converting heavy feedstocks with high amounts of impurities. The process enables the conversion of atmospheric or vacuum residues at temperatures up to 440 degrees C, and at liquid hourly space velocity (LHSV) conditions in the range of 0.15 to 0.5 per hour. A 540 degrees C conversion of up to 80 weight per cent can be achieved under these conditions. This paper reported on a research study conducted at IFP Lyon in which the residue hydroconversion in a large-scale ebullated bed bench unit was investigated to determine the impact of operating conditions and feed properties on yield and product qualities. Hydrogen was added to the feed in the bench units to keep a high hydrogen partial pressure and favour the catalytic hydroconversion reactions. In a typical test, the reactor was fed with 50 g of feedstock and 0.45 g of crushed equilibrium industrial NiMo catalyst, pressurized hydrogen and quickly heated at the reaction temperature. This paper also discussed the conversion of Athabasca bitumen residue in the large-scale pilot plant and also in the small scale batch reactor. The effect of operating temperature and space velocity was examined. The reactivity of the saturates, aromatics, resins and asphaltenes (SARA) fractions of the bitumen was studied separately in order to better understand the conversion mechanisms and reactivities. The Athabasca bitumen feed and SARA fractions were also analyzed in terms of standard petroleum analysis, SARA fractionation, elemental analysis, size exclusion chromatography (SEC) and 13C NMR. Hydroconversion experiments were conducted in the batch unit at different reaction temperatures and reaction times. A comparison of small-scale batch results with those obtained with the continuous large-scale bench

  19. Life-cycle assessment of transportation biofuels from hydrothermal liquefaction of forest residues in British Columbia.

    Science.gov (United States)

    Nie, Yuhao; Bi, Xiaotao

    2018-01-01

    Biofuels from hydrothermal liquefaction (HTL) of abundantly available forest residues in British Columbia (BC) can potentially make great contributions to reduce the greenhouse gas (GHG) emissions from the transportation sector. A life-cycle assessment was conducted to quantify the GHG emissions of a hypothetic 100 million liters per year HTL biofuel system in the Coast Region of BC. Three scenarios were defined and investigated, namely, supply of bulky forest residues for conversion in a central integrated refinery (Fr-CIR), HTL of forest residues to bio-oil in distributed biorefineries and subsequent upgrading in a central oil refinery (Bo-DBR), and densification of forest residues in distributed pellet plants and conversion in a central integrated refinery (Wp-CIR). The life-cycle GHG emissions of HTL biofuels is 20.5, 17.0, and 19.5 g CO 2 -eq/MJ for Fr-CIR, Bo-DBR, and Wp-CIR scenarios, respectively, corresponding to 78-82% reduction compared with petroleum fuels. The conversion stage dominates the total GHG emissions, making up more than 50%. The process emitting most GHGs over the life cycle of HTL biofuels is HTL buffer production. Transportation emission, accounting for 25% of Fr-CIR, can be lowered by 83% if forest residues are converted to bio-oil before transportation. When the credit from biochar applied for soil amendment is considered, a further reduction of 6.8 g CO 2 -eq/MJ can be achieved. Converting forest residues to bio-oil and wood pellets before transportation can significantly lower the transportation emission and contribute to a considerable reduction of the life-cycle GHG emissions. Process performance parameters (e.g., HTL energy requirement and biofuel yield) and the location specific parameter (e.g., electricity mix) have significant influence on the GHG emissions of HTL biofuels. Besides, the recycling of the HTL buffer needs to be investigated to further improve the environmental performance of HTL biofuels.

  20. Organochlorine Pesticide Residues in the Major Rivers of Southern Thailand

    Directory of Open Access Journals (Sweden)

    Abd Naser Haji Samoh

    2009-01-01

    Full Text Available Environmental contaminations by organochlorine pesticides (OCPs of inland water have been a global issue, since most of these compounds are very persistent, bioaccumulative and toxic compounds. Due to the widespread use of DDT for malaria vector eradication programs in the past and no comprehensive works have been conducted to assess trace organic pollutants in river waters, this work is the first effort to assess the contamination levels of OCPs in the major rivers of Southern Thailand. The objectives of this study were to determine the concentration levels of OCPs and oil and grease in the 3 major rivers and to compare the present results with surrounding regions for further assessment of OCPs contamination status in inland waters of Southern Thailand. The water samples were collected along the 3 major rivers (Saiburi, Patani and Tiba River during June 2007-February 2008. Water samples were solid phase extracted with Supelco C-18 cartridge (1g/6 mL and quantified by gas chromatograph (GC-ECD. The concentration of oil and grease was determined by gravimetric method and reported as hexane extractable material (HEM and silica gel treated hexane extractable material (SGT-HEM. Several parameters of waters such as total suspended solid, pH, turbidity, and conductivity were measured. The commonly found OCP residues in these rivers were β-HCH, γ-HCH, heptachlor epoxide, endosulfan 1, p,p’- DDE and endrin aldehyde. The overall results showed that Saiburi River was more polluted with OCPs than Patani and Tiba River, especially p, p’-DDE which was detected in the wide range concentration of 9.6 to 203.1 ng/mL. For oil and grease contamination, Tiba River waters were found to be more polluted than either Patani or Saiburi River. The experimental procedures and analytical results together with the possible sources of OCPs and its environmental impacts are presented.

  1. Landfill gas

    International Nuclear Information System (INIS)

    Hartnell, Gaynor

    2000-01-01

    Following the UK Government's initiative for stimulating renewable energy through the Non-Fossil Fuel Obligation (NFFO), the UK landfill gas industry has more than trebled in size in just 4 years. As a result, UK companies are now in a strong position to offer their skills and services overseas. Ireland, Greece and Spain also resort heavily to disposal to landfill. Particularly rapid growth of the landfill gas market is expected in the OECD-Pacific and NAFTA areas. The article explains that landfill gas is a methane-rich mixture produced by anaerobic decomposition of organic wastes in landfills: under optimum conditions, up to 500 cubic meters of gas can be obtained from 1 tonne of biodegradable waste. Data on the number and capacity of sites in the UK are given. The Landfill Gas Association runs courses to counteract the skills shortage in the UK, and tailored courses for overseas visitors are planned

  2. Evaluation of Crops Sensitivity to Atrazine Soil Residual

    Directory of Open Access Journals (Sweden)

    E Izadi

    2012-02-01

    Full Text Available Abstract In order to study the sensitivity of 9 crops to atrazine soil residual, two separate experiments were conducted in field and greenhouse conditions. First experiment was conducted in a field with treated soil by atrazine based on split plot and the results evaluated in greenhouse conditions. Treatments in the field experiment included two organic manure application rates (0 and 50 t/ha as main plots and 2 atrazine application rates (2 and 4 kg/ha atrazine a.i. as sob plots. After corn harvesting soil was sampled at 0-15 cm surface layer in each plots in 15 points, after mixing the samples. Wheat, barley, sugar beet, pea, lens and colza planted in pots at greenhouse. Second experiment conducted in greenhouse conditions for evaluation of atrazine soil residual in completely randomized design. Treatments included atrazine soil residual concentrations (0, 0.2, 0.5, 1, 5, 10 and 15 mg/kg soil and crops included wheat, barley, sugar beet, pea, lens, rape, bean and tomato. Results showed that atrazine residue had no effect on crops growth in field experiment treated with atrazine. It seems that atrazine residue in filed soil is lower that its damage threshold for crops or maybe for its fast removal in field than in control conditions. But in bioassay experiment (greenhouse experiment crops response to atrazine residues were different. Results showed that onion and pea were most susceptible ant tolerant crops between studied species and based of ED50 parameter the other crops tolerance to total residue ranked as: pea< bean< lentil< sugar beet< tomato< barley< wheat< rape< onion. Keywords: Atrazine residue, Pea, Bean, Lentil, Sugar beet, Barley, Wheat, Rape, Tomato

  3. Residual stress by repair welds

    International Nuclear Information System (INIS)

    Mochizuki, Masahito; Toyoda, Masao

    2003-01-01

    Residual stress by repair welds is computed using the thermal elastic-plastic analysis with phase-transformation effect. Coupling phenomena of temperature, microstructure, and stress-strain fields are simulated in the finite-element analysis. Weld bond of a plate butt-welded joint is gouged and then deposited by weld metal in repair process. Heat source is synchronously moved with the deposition of the finite-element as the weld deposition. Microstructure is considered by using CCT diagram and the transformation behavior in the repair weld is also simulated. The effects of initial stress, heat input, and weld length on residual stress distribution are studied from the organic results of numerical analysis. Initial residual stress before repair weld has no influence on the residual stress after repair treatment near weld metal, because the initial stress near weld metal releases due to high temperature of repair weld and then stress by repair weld regenerates. Heat input has an effect for residual stress distribution, for not its magnitude but distribution zone. Weld length should be considered reducing the magnitude of residual stress in the edge of weld bead; short bead induces high tensile residual stress. (author)

  4. Confirmation of the sterilization effect using a high concentration of ozone gas for the bio-clean room.

    Science.gov (United States)

    Iwamura, Takuji; Nagano, Katsunori; Nogami, Toshihiro; Matsuki, Noritomo; Kosaka, Noriyoshi; Shintani, Hideharu; Katoh, Miyoshi

    2013-01-01

    A high-level aseptic environment must be maintained in bio-cleanrooms used for the manufacture of sterile products. In the past, formaldehyde gas was most commonly used to sterilize bio-cleanrooms, but due to strict residual limitations there has been a need to develop a less toxic alternative choice. The authors have developed a revolutionary new sterilization system using a high concentration of ozone gas and used this system to sterilize an actual bio-cleanroom. This system integrates the ozone gas generator with the air conditioning system by proper control. The design specifications for the system included an ozone gas concentration of 200 ppm or more, relative humidity of 80% or more, and a sterilizing time of 120 min. Blow vents and suction ports were placed to ensure a uniform airflow which would extend through the entire room during ozone gas sterilization. Tests regarding long-term material exposure to ozone gas were conducted when the system was introduced to distinguish usable and unusable materials. In an actually constructed cleanroom, simulations were used to predict the evenness of the diffusion of ozone gas concentration and relative humidity during ozone gas sterilization, and measurements of the actual indoor ozone gas concentration, temperature and relative humidity during sterilization revealed that the ozone concentration and relative humidity needed for sterilization had been achieved generally throughout the entire environment. In addition, the CT value (mg/m(3) (=ppm) × min) , derived by multiplying the ozone gas concentration during ozone gas sterilization by the sterilization time, was equal to or greater than the target value of 24 × 10(3) (ppm·min) . When the results of sterilization in a cleanroom were confirmed using a biological indicator (BI) , negative results were obtained at all measurement points, demonstrating that sterilization was being performed effectively in the actual factory at which the ozone gas sterilization system

  5. Deregulated gas in 1985 seen costly

    Energy Technology Data Exchange (ETDEWEB)

    Schaffer, P.

    1980-05-05

    Deregulation of natural gas wellhead prices will mean higher prices for nonboiler industrial users, according to an Energy and Environmental Analysis Inc. (EEA) study. The price increases of high-sulfur residual fuel oil will exceed inflation rates, but low-sulfur residual oil and distillate oil will have smaller increases because of upgraded refineries. Te economc imact analysis is broken down by region and includes estimates of gas, high-sulfur coal, and low-sulfur coal prices thrugh 1995. Free copies of the report are available from the Federal Energy Regulatory Commission's Office of Public Information. (DCK)

  6. RESIDUAL RISK ASSESSMENT: ETHYLENE OXIDE ...

    Science.gov (United States)

    This document describes the residual risk assessment for the Ethylene Oxide Commercial Sterilization source category. For stationary sources, section 112 (f) of the Clean Air Act requires EPA to assess risks to human health and the environment following implementation of technology-based control standards. If these technology-based control standards do not provide an ample margin of safety, then EPA is required to promulgate addtional standards. This document describes the methodology and results of the residual risk assessment performed for the Ethylene Oxide Commercial Sterilization source category. The results of this analyiss will assist EPA in determining whether a residual risk rule for this source category is appropriate.

  7. Grinding of Inconel 713 superalloy for gas turbines

    Czech Academy of Sciences Publication Activity Database

    Čapek, J.; Kyncl, J.; Kolařík, K.; Beránek, L.; Pitrmuc, Z.; Medřický, Jan; Pala, Z.

    2016-01-01

    Roč. 16, č. 1 (2016), s. 14-15 ISSN 1213-2489 Institutional support: RVO:61389021 Keywords : Casting defects * Gas turbine * Grinding * Nickel superalloy * Residual stresses Subject RIV: JJ - Other Materials

  8. The environmental impact in the production of petroleum and gas

    International Nuclear Information System (INIS)

    RodrIguez, N. . E mail: norma@info.isctn.edu.cu.

    2004-01-01

    This work describe the situation of oil and gas wells as generators of environment impact. Describe the most important characteristics of the effluents (liquids), solids residuals and emissions. Give some advises to mitigate the impact

  9. Perioperative functional residual capacity.

    Science.gov (United States)

    Wahba, R W

    1991-04-01

    The literature dealing with the magnitude, mechanism and effects of reduced FRC in the perioperative period is reviewed. During general anaesthesia FRC is reduced by approximately 20%. The reduction is greater in the obese and in patients with COPD. The most likely mechanism is the loss of inspiratory muscle tone of the muscles acting on the rib cage. Gas trapping is an additional mechanism. Lung compliance decreases and airways resistance increases, in large part, due to decreased FRC. The larynx is displaced anteriorly and elongated, making laryngoscopy and intubation more difficult. The change in FRC creates or increases intrapulmonary shunt and areas of low ventilation to perfusion. This is due to the occurrence of compression atelectasis, and to regional changes in mechanics and airway closure which tend to reduce ventilation to dependent lung zones which are still well perfused. Abdominal and thoracic operations tend to increase shunting further. Large tidal volume but not PEEP will improve oxygenation, although both increase FRC. Both FRC and vital capacity are reduced following abdominal and thoracic surgery in a predictable pattern. The mechanism is the combined effect of incisional pain and reflex dysfunction of the diaphragm. Additional effects of thoracic surgery include pleural effusion, cooling of the phrenic nerve and mediastinal widening. Postoperative hypoxaemia is a function of reduced FRC and airway closure. There is no real difference among the various methods of active lung expansion in terms of the speed of restoration of lung function, or in preventing postoperative atelectasis/pneumonia. Epidural analgesia does not influence the rate of recovery of lung function, nor does it prevent atelectasis/pneumonia.

  10. Multidimensional Heat Conduction

    DEFF Research Database (Denmark)

    Rode, Carsten

    1998-01-01

    Analytical theory of multidimensional heat conduction. General heat conduction equation in three dimensions. Steay state, analytical solutions. The Laplace equation. Method of separation of variables. Principle of superposition. Shape factors. Transient, multidimensional heat conduction....

  11. Asian gas

    International Nuclear Information System (INIS)

    Masuda, T.

    1990-01-01

    This paper reports on natural gas which now appears ready to take a leading role on the world energy stage. Demand for natural gas, and specifically LNG, will be strong throughout the world, particularly in Asia. Indonesia and Malaysia will become much more dependent on natural gas in the Asian market. In Thailand, where remarkable economic growth has been fueled by imported oil and domestically produced natural gas, LNG may soon have to be imported from neighboring countries. The author sees Thailand's imports of natural gas increasing from 1.5 to 4.5 million tons annually. Similarly, Korea's imports of LNG will rise from 2 to 8 million tons between 1987 and 2000. In Japan, energy demand is expected to increase at an even faster rate in the 1990s. Given the opposition to nuclear power generation and growing concern about the greenhouse effect, it is likely that LNG will satisfy a major portion of Japan's increasing demand for energy. Japanese gas companies are studying the possibility of establishing a national pipeline network to move gas beyond metropolitan areas

  12. Studies on bound (14)C-chlorsulfuron residues in soil.

    Science.gov (United States)

    Guo, Jiangfeng; Sun, Jinhe

    2002-04-10

    The cause for phytotoxicity of bound residues of chlorsulfuron (2-chloro-N-[[4-methoxy-6-methyl-1,3,5-triazin-2-yl)amino] carbonyl]benzenesulfonamide) to rotational crops is unknown. This study was conducted to determine the formation of nonextractable (bound) residues of chlorsulfuron in soil, and the distribution of bound residues in different organic matter fractions. The results showed that over 150 days, the extractable fraction of (14)C-residues decreased to 25.1% of applied chlorsulfuron, while bound residues concurrently increased to 47.1%. The distribution of (14)C-bound residues in soil organic matter fractions followed an order of humic acid (HA) humin humin fraction increased with time. After soil treatment by autoclaving, it was found that bound (14)C-chlorsulfuron residues became available again in the soil. One of the released products was 2-amino-4-hydroxyl-6-methyl-1,3,5-triazine (identified by GC-MS), which is a degradation product of chlorsulfuron.

  13. Nitrogen availability of biogas residues

    Energy Technology Data Exchange (ETDEWEB)

    El-Sayed Fouda, Sara

    2011-09-07

    The objectives of this study were to characterize biogas residues either unseparated or separated into a liquid and a solid phase from the fermentation of different substrates with respect to their N and C content. In addition, short and long term effects of the application of these biogas residues on the N availability and N utilization by ryegrass was investigated. It is concluded that unseparated or liquid separated biogas residues provide N at least corresponding to their ammonium content and that after the first fertilizer application the C{sub org}:N{sub org} ratio of the biogas residues was a crucial factor for the N availability. After long term application, the organic N accumulated in the soil leads to an increased release of N.

  14. Residual stress analysis: a review

    International Nuclear Information System (INIS)

    Finlayson, T.R.

    1983-01-01

    The techniques which are or could be employed to measure residual stresses are outlined. They include X-ray and neutron diffraction. Comments are made on the reliability and accuracy to be expected from particular techniques

  15. OECD Maximum Residue Limit Calculator

    Science.gov (United States)

    With the goal of harmonizing the calculation of maximum residue limits (MRLs) across the Organisation for Economic Cooperation and Development, the OECD has developed an MRL Calculator. View the calculator.

  16. Measurement of residual CO2 saturation at a geological storage site using hydraulic tests

    Science.gov (United States)

    Rötting, T. S.; Martinez-Landa, L.; Carrera, J.; Russian, A.; Dentz, M.; Cubillo, B.

    2012-12-01

    Estimating long term capillary trapping of CO2 in aquifers remains a key challenge for CO2 storage. Zhang et al. (2011) proposed a combination of thermal, tracer, and hydraulic experiments to estimate the amount of CO2 trapped in the formation after a CO2 push and pull test. Of these three types of experiments, hydraulic tests are the simplest to perform and possibly the most informative. However, their potential has not yet been fully exploited. Here, a methodology is presented to interpret these tests and analyze which parameters can be estimated. Numerical and analytical solutions are used to simulate a continuous injection in a porous medium where residual CO2 has caused a reduction in hydraulic conductivity and an increase in storativity over a finite thickness (a few meters) skin around the injection well. The model results are interpreted using conventional pressure build-up and diagnostic plots (a plot of the drawdown s and the logarithmic derivative d s / d ln t of the drawdown as a function of time). The methodology is applied using the hydraulic parameters estimated for the Hontomin site (Northern Spain) where a Technology Demonstration Plant (TDP) for geological CO2 storage is planned to be set up. The reduction of hydraulic conductivity causes an increase in observed drawdowns, the increased storativity in the CO2 zone causes a delay in the drawdown curve with respect to the reference curve measured before CO2 injection. The duration (characteristic time) of these effects can be used to estimate the radius of the CO2 zone. The effects of reduced permeability and increased storativity are well separated from wellbore storage and natural formation responses, even if the CO2-brine interface is inclined (i.e. the CO2 forms a cone around the well). We find that both skin hydraulic conductivity and storativity (and thus residual CO2 saturation) can be obtained from the water injection test provided that water flow rate is carefully controlled and head build

  17. Gas turbines

    Energy Technology Data Exchange (ETDEWEB)

    Farahan, E.; Eudaly, J.P.

    1978-10-01

    This evaluation provides performance and cost data for commercially available simple- and regenerative-cycle gas turbines. Intercooled, reheat, and compound cycles are discussed from theoretical basis only, because actual units are not currently available, except on a special-order basis. Performance characteristics investigated include unit efficiency at full-load and off-design conditions, and at rated capacity. Costs are tabulated for both simple- and regenerative-cycle gas turbines. The output capacity of the gas turbines investigated ranges from 80 to 134,000 hp for simple units and from 12,000 to 50,000 hp for regenerative units.

  18. Noble Gas Leak Detector for Use in the SNS Neutron Electric Dipole Moment Experiment

    Science.gov (United States)

    Barrow, Chad; Huffman, Paul; Leung, Kent; Korobkina, Ekaterina; White, Christian; nEDM Collaboration Collaboration

    2017-09-01

    Common practice for leak-checking high vacuum systems uses helium as the probing gas. However, helium may permeate some materials at room temperature, making leak characterization difficult. The experiment to find a permanent electric dipole moment of the neutron (nEDM), to be conducted at Oak Ridge National Laboratories, will employ a large volume of liquid helium housed by such a helium-permeable composite material. It is desirable to construct a leak detector that can employ alternative test gases. The purpose of this experiment is to create a leak detector that can quantify the argon gas flux in a high vacuum environment and interpret this flux as a leak-rate. This apparatus will be used to check the nEDM volumes for leaks at room temperature before cooling down to cryogenic temperatures. Our leak detector uses a residual gas analyzer and a vacuum pumping station to characterize the gas present in an evacuated volume. The introduction of argon gas into the system is interpreted as a leak-rate into the volume. The device has been calibrated with NIST certified calibrated leaks and the machine's sensitivity has been calculated using background gas analysis. As a result of the device construction and software programming, we are able to leak-check composite and polyamide volumes This work was supported in part by the US Department of Energy under Grant No. DE-FG02-97ER41042.

  19. Thermal Conductivity of Foam Glasses Prepared using High Pressure Sintering

    DEFF Research Database (Denmark)

    Østergaard, Martin Bonderup; Petersen, Rasmus Rosenlund; König, Jakob

    The increasing focus on better building insulation is important to lower energy consumption. Development of new and improved insulation materials can contribute to solving this problem. Foam glass has a good insulating effect due to its large gas volume (porosity >90 %). It can be produced with o...... the thermal conductivity varies with gas composition. This allows us to determine the contribution of the gas and solid phase to the total thermal conductivity of a foam glass....

  20. Vesícula residual

    Directory of Open Access Journals (Sweden)

    Júlio C. U. Coelho

    Full Text Available Our objective is to report three patients with recurrent severe upper abdominal pain secondary to residual gallbladder. All patients had been subjected to cholecystectomy from 1 to 20 years before. The diagnosis was established after several episodes of severe upper abdominal pain by imaging exams: ultrasonography, tomography, or endoscopic retrograde cholangiography. Removal of the residual gallbladder led to complete resolution of symptoms. Partial removal of the gallbladder is a very rare cause of postcholecystectomy symptoms.