WorldWideScience

Sample records for residual capacity frc

  1. On the residual properties of damaged FRC

    Science.gov (United States)

    Zerbino, R.; Torrijos, M. C.; Giaccio, G.

    2017-09-01

    A discussion on the residual behaviour of Fibre Reinforced Concrete (FRC) is performed based on two selected cases of concrete degradation: the exposure at High Temperatures and the development of Alkali Silica Reactions. In addition, and taking in mind that the failure mechanism in FRC is strongly related with the fibre pull-out strength, the bond strength in damaged matrices was shown concluding that the residual bond strength is less affected than the matrix strength. As the damage increases, the compressive strength and the modulus of elasticity decrease, being the modulus of elasticity the most affected. There were no significant changes produced by the incorporation of fibres on the residual behaviour when compared with previous experience on plain damage concrete. Regarding the tensile behaviour although the first peak decreases as the damage increases, even for a severely damage FRC the residual stresses remain almost unaffected.

  2. Functional residual capacity (FRC) and lung clearance index (LCI) in mechanically ventilated infants: application in the newborn with congenital diaphragmatic hernia (CDH).

    Science.gov (United States)

    Landolfo, Francesca; Savignoni, Ferdinando; Capolupo, Irma; Columbo, Claudia; Calzolari, Flaminia; Giliberti, Paola; Chukhlantseva, Natalia; Bagolan, Pietro; Dotta, Andrea

    2013-07-01

    Functional residual capacity (FRC) and lung clearance index (LCI) are sensitive parameters for early detection of airway disease in infancy. The closed helium dilution method has been applied to assess lung volume and ventilation inhomogeneity (VI) in spontaneously breathing infants. The aims of this study were as follows: (1) to assess applicability of the helium gas dilution technique in mechanically ventilated infants with high-risk congenital diaphragmatic hernia (CDH) and to evaluate changes in breathing patterns, lung volume, and VI during the first days of life before and after surgery, and (2) to analyze the possible correlation between changes in lung volume, cerebral hemodynamics, and oxygenation before and after surgical correction of CDH through near-infrared spectroscopy (NIRS) monitoring. Lung function tests were performed by multibreath washout traces with an ultrasonic flowmeter and helium gas dilution technique. For all babies, three acceptable FRC and LCI measurements were collected for each test (mean and SD of three measurements were calculated) before surgery (T0), 24 h after surgery (T1) during mechanical ventilation, and within 24 h after extubation in spontaneous breathing (T2). Cerebral and splanchnic hemodynamics were continuously monitored by NIRS during mechanical ventilation to evaluate relationships between changes in lung volume and capillary-venous oxyhemoglobin saturation in tissues. Fraction of inspired oxygen delivered was adjusted to keep oxygen saturation between 90% and 95%. Thirteen CDH infants were studied; median GA = 38 weeks (range 35-41) and median BW = 3000 g (range 1850-3670). FRC and LCI significantly improved after extubation when compared with pre-surgical values. No differences were found in tidal volume (Vt) and NIRS monitoring before and after surgery and after extubation. Neither LCI nor FRC was correlated with NIRS values. Helium gas dilution technique is an applicable and reliable technique to measure lung

  3. Perioperative functional residual capacity.

    Science.gov (United States)

    Wahba, R W

    1991-04-01

    The literature dealing with the magnitude, mechanism and effects of reduced FRC in the perioperative period is reviewed. During general anaesthesia FRC is reduced by approximately 20%. The reduction is greater in the obese and in patients with COPD. The most likely mechanism is the loss of inspiratory muscle tone of the muscles acting on the rib cage. Gas trapping is an additional mechanism. Lung compliance decreases and airways resistance increases, in large part, due to decreased FRC. The larynx is displaced anteriorly and elongated, making laryngoscopy and intubation more difficult. The change in FRC creates or increases intrapulmonary shunt and areas of low ventilation to perfusion. This is due to the occurrence of compression atelectasis, and to regional changes in mechanics and airway closure which tend to reduce ventilation to dependent lung zones which are still well perfused. Abdominal and thoracic operations tend to increase shunting further. Large tidal volume but not PEEP will improve oxygenation, although both increase FRC. Both FRC and vital capacity are reduced following abdominal and thoracic surgery in a predictable pattern. The mechanism is the combined effect of incisional pain and reflex dysfunction of the diaphragm. Additional effects of thoracic surgery include pleural effusion, cooling of the phrenic nerve and mediastinal widening. Postoperative hypoxaemia is a function of reduced FRC and airway closure. There is no real difference among the various methods of active lung expansion in terms of the speed of restoration of lung function, or in preventing postoperative atelectasis/pneumonia. Epidural analgesia does not influence the rate of recovery of lung function, nor does it prevent atelectasis/pneumonia.

  4. Manual hyperinflation partly prevents reductions of functional residual capacity in cardiac surgical patients--a randomized controlled trial

    NARCIS (Netherlands)

    Paulus, Frederique; Veelo, Denise P.; de Nijs, Selma B.; Beenen, Ludo F. M.; Bresser, Paul; de Mol, Bas A. J. M.; Binnekade, Jan M.; Schultz, Marcus J.

    2011-01-01

    Cardiac surgery is associated with post-operative reductions of functional residual capacity (FRC). Manual hyperinflation (MH) aims to prevent airway plugging, and as such could prevent the reduction of FRC after surgery. The main purpose of this study was to determine the effect of MH on

  5. Measurements of functional residual capacity during intensive care treatment: the technical aspects and its possible clinical applications.

    Science.gov (United States)

    Heinze, H; Eichler, W

    2009-10-01

    Direct measurement of lung volume, i.e. functional residual capacity (FRC) has been recommended for monitoring during mechanical ventilation. Mostly due to technical reasons, FRC measurements have not become a routine monitoring tool, but promising techniques have been presented. We performed a literature search of studies with the key words 'functional residual capacity' or 'end expiratory lung volume' and summarize the physiology and patho-physiology of FRC measurements in ventilated patients, describe the existing techniques for bedside measurement, and provide an overview of the clinical questions that can be addressed using an FRC assessment. The wash-in or wash-out of a tracer gas in a multiple breath maneuver seems to be best applicable at bedside, and promising techniques for nitrogen or oxygen wash-in/wash-out with reasonable accuracy and repeatability have been presented. Studies in ventilated patients demonstrate that FRC can easily be measured at bedside during various clinical settings, including positive end-expiratory pressure optimization, endotracheal suctioning, prone position, and the weaning from mechanical ventilation. Alveolar derecruitment can easily be monitored and improvements of FRC without changes of the ventilatory setting could indicate alveolar recruitment. FRC seems to be insensitive to over-inflation of already inflated alveoli. Growing evidence suggests that FRC measurements, in combination with other parameters such as arterial oxygenation and respiratory compliance, could provide important information on the pulmonary situation in critically ill patients. Further studies are needed to define the exact role of FRC in monitoring and perhaps guiding mechanical ventilation.

  6. Impact of changes of positive end-expiratory pressure on functional residual capacity at low tidal volume ventilation during general anesthesia

    OpenAIRE

    Satoh, Daizoh; Kurosawa, Shin; Kirino, Wakaba; Wagatsuma, Toshihiro; Ejima, Yutaka; Yoshida, Akiko; Toyama, Hiroaki; Nagaya, Kei

    2012-01-01

    Purpose Several reports in the literature have described the effects of positive end-expiratory pressure (PEEP) level upon functional residual capacity (FRC) in ventilated patients during general anesthesia. This study compares FRC in mechanically low tidal volume ventilation with different PEEP levels during upper abdominal surgery. Methods Before induction of anesthesia (awake) for nine patients with upper abdominal surgery, a tight-seal facemask was applied with 2 cmH2O pressure support ve...

  7. Impact of changes of positive end-expiratory pressure on functional residual capacity at low tidal volume ventilation during general anesthesia.

    Science.gov (United States)

    Satoh, Daizoh; Kurosawa, Shin; Kirino, Wakaba; Wagatsuma, Toshihiro; Ejima, Yutaka; Yoshida, Akiko; Toyama, Hiroaki; Nagaya, Kei

    2012-10-01

    Several reports in the literature have described the effects of positive end-expiratory pressure (PEEP) level upon functional residual capacity (FRC) in ventilated patients during general anesthesia. This study compares FRC in mechanically low tidal volume ventilation with different PEEP levels during upper abdominal surgery. Before induction of anesthesia (awake) for nine patients with upper abdominal surgery, a tight-seal facemask was applied with 2 cmH(2)O pressure support ventilation and 100 % O(2) during FRC measurements conducted on patients in a supine position. After tracheal intubation, lungs were ventilated with bilevel airway pressure with a volume guarantee (7 ml/kg predicted body weight) and with an inspired oxygen fraction (FIO(2)) of 0.4. PEEP levels of 0, 5, and 10 cmH(2)O were used. Each level of 5 and 10 cmH(2)O PEEP was maintained for 2 h. FRC was measured at each PEEP level. FRC awake was significantly higher than that at PEEP 0 cmH(2)O (P cmH(2)O was significantly lower than that at 10 cmH(2)O (P cmH(2)O (P cmH(2)O was significantly lower than that for PEEP 5 cmH(2)O or PEEP 10 cmH(2)O (P cmH(2)O, PEEP 5 cmH(2)O after 2 h, and PEEP 10 cmH(2)O after 2 h were correlated with FRC (R = 0.671, P cmH(2)O is necessary to maintain lung function if low tidal volume ventilation is used during upper abdominal surgery.

  8. Functional residual capacity increase during laparoscopic surgery with abdominal wall lift

    Directory of Open Access Journals (Sweden)

    Hiroshi Ueda

    Full Text Available Abstract Background and objectives: The number of laparoscopic surgeries performed is increasing every year and in most cases the pneumoperitoneum method is used. One alternative is the abdominal wall lifting method and this study was undertaken to evaluate changes of functional residual capacity during the abdominal wall lift procedure. Methods: From January to April 2013, 20 patients underwent laparoscopic cholecystectomy at a single institution. All patients were anesthetized using propofol, remifentanil and rocuronium. FRC was measured automatically by Engstrom Carestation before the abdominal wall lift and again 15 minutes after the start of the procedure. Results: After abdominal wall lift, there was a significant increase in functional residual capacity values (before abdominal wall lift 1.48 × 103 mL, after abdominal wall lift 1.64 × 103 mL (p < 0.0001. No complications such as desaturation were observed in any patient during this study. Conclusions: Laparoscopic surgery with abdominal wall lift may be appropriate for patients who have risk factors such as obesity and respiratory disease.

  9. The Bradyrhizobium japonicum frcB Gene Encodes a Diheme Ferric Reductase ▿†

    Science.gov (United States)

    Small, Sandra K.; O'Brian, Mark R.

    2011-01-01

    Iron utilization by bacteria in aerobic environments involves uptake as a ferric chelate from the environment, followed by reduction to the ferrous form. Ferric iron reduction is poorly understood in most bacterial species. Here, we identified Bradyrhizobium japonicum frcB (bll3557) as a gene adjacent to, and coregulated with, the pyoR gene (blr3555) encoding the outer membrane receptor for transport of a ferric pyoverdine. FrcB is a membrane-bound, diheme protein, characteristic of eukaryotic ferric reductases. Heme was essential for FrcB stability, as were conserved histidine residues in the protein that likely coordinate the heme moieties. Expression of the frcB gene in Escherichia coli conferred ferric reductase activity on those cells. Furthermore, reduced heme in purified FrcB was oxidized by ferric iron in vitro. B. japonicum cells showed inducible ferric reductase activity in iron-limited cells that was diminished in an frcB mutant. Steady-state levels of frcB mRNA were strongly induced under iron-limiting conditions, but transcript levels were low and unresponsive to iron in an irr mutant lacking the global iron response transcriptional regulator Irr. Thus, Irr positively controls the frcB gene. FrcB belongs to a family of previously uncharacterized proteins found in many proteobacteria and some cyanobacteria. This suggests that membrane-bound, heme-containing ferric reductase proteins are not confined to eukaryotes but may be common in bacteria. PMID:21705608

  10. The Bradyrhizobium japonicum frcB gene encodes a diheme ferric reductase.

    Science.gov (United States)

    Small, Sandra K; O'Brian, Mark R

    2011-08-01

    Iron utilization by bacteria in aerobic environments involves uptake as a ferric chelate from the environment, followed by reduction to the ferrous form. Ferric iron reduction is poorly understood in most bacterial species. Here, we identified Bradyrhizobium japonicum frcB (bll3557) as a gene adjacent to, and coregulated with, the pyoR gene (blr3555) encoding the outer membrane receptor for transport of a ferric pyoverdine. FrcB is a membrane-bound, diheme protein, characteristic of eukaryotic ferric reductases. Heme was essential for FrcB stability, as were conserved histidine residues in the protein that likely coordinate the heme moieties. Expression of the frcB gene in Escherichia coli conferred ferric reductase activity on those cells. Furthermore, reduced heme in purified FrcB was oxidized by ferric iron in vitro. B. japonicum cells showed inducible ferric reductase activity in iron-limited cells that was diminished in an frcB mutant. Steady-state levels of frcB mRNA were strongly induced under iron-limiting conditions, but transcript levels were low and unresponsive to iron in an irr mutant lacking the global iron response transcriptional regulator Irr. Thus, Irr positively controls the frcB gene. FrcB belongs to a family of previously uncharacterized proteins found in many proteobacteria and some cyanobacteria. This suggests that membrane-bound, heme-containing ferric reductase proteins are not confined to eukaryotes but may be common in bacteria.

  11. Functional residual capacity measurement by heptafluoropropane in ventilated newborn lungs

    OpenAIRE

    Kusztrich, Ariane

    2012-01-01

    Objective: Heptafluoropropane is an inert gas commercially used as propellant for inhalers. Since heptafluoropropane can be detected in low concentrations, it could also be used as a tracer gas to measure functional residual capacity. The aim of the present study was to validate functional residual capacity measurements by heptafluoropropane wash-in/wash-out (0.8%) during mechanical ventilation in small, surfactant-depleted lungs using a newborn piglet model. Design: Prospective laborato...

  12. Residual capacity estimation of bridges using structural health monitoring data

    Science.gov (United States)

    Baghaei, Reza; Feng, Maria Q.; Torbol, Marco

    2011-04-01

    In this study, a vibration-based procedure for residual capacity estimation of bridges after damaging earthquake events is proposed. The procedure starts with estimation of collapse capacity of the intact bridge using incremental dynamic analysis (IDA) curves. The collapse capacity is defined as the median intensity level of the earthquakes that cause global or local collapse within the structure. A database of post-earthquake modal properties is created by calculating the analytical modal properties of the bridge after each nonlinear response history analysis performed for generation IDA curves. After the damaging event, experimental modal properties of the bridge are identified from vibration measurements of the bridge. These properties along with the modal properties database are used to find ground motionintensity pairs that can drive nonlinear FE model of the structure to the current damage state of the bridge. The IDA curves corresponding to the damaged FE model of the bridge are subsequently used to estimate amount of loss in collapse capacity of the damaged structure. Estimated loss in capacity of the bridge besides the bridge-site-specific seismic hazard curves are used to update the functionality status of the bridge. Proposed procedure is applied to experimental data from a large-scale shake table test on a quarter-scale model of a short-span reinforced concrete bridge. The bridge was subjected to a series of earthquake ground motions introducing progressive seismic damage to the bridge which finally led to the failure of one of the bents. Residual collapse capacity and functionality status of the bridge are updated at different stages of the experiment using the proposed procedure.

  13. Recent results on the FRC transport

    International Nuclear Information System (INIS)

    Tuszewski, M.

    1984-01-01

    Some recent transport studies of field-reversed configurations (FRC) during their equilibrium phase are presented. The FRC confinement times of interest tau/sub N/, tau/sub E/, and tau/ sub phi/ are for particles, energy, and trapped-flux, respectively. An analytical expression for tau/sub N/ based on Lower-Hybrid-Drift (LHD) resistivity is presented. Some progress in assessing the respective contributions of radiation and thermal conduction to tau/sub E/ is given. Finally, the relation tau/sub E/ less than or equal to tau/sub phi/ is discussed

  14. Sustainable Materials Management (SMM) Food Recovery Challenge (FRC) Data

    Data.gov (United States)

    U.S. Environmental Protection Agency — As part of EPA's Food Recovery Challenge (FRC), organizations pledge to improve their sustainable food management practices and report their results. The FRC is part...

  15. 20 CFR 220.120 - The claimant's residual functional capacity.

    Science.gov (United States)

    2010-04-01

    ... limitations that go beyond the symptoms, such as pain, that are important in the diagnosis and treatment of... with a low back disorder may be fully capable of the physical demands consistent with those of... functional capacity. (a) General. The claimant's impairment(s), and any related symptoms, such as pain, may...

  16. Development of Fracture Energy of FRC Materials. Freeze-Thaw Resistance of FRC Materials

    DEFF Research Database (Denmark)

    Stoklund Larsen, E.

    During the past four years research has been carried out at the Danish Building Research Institute on different aspects of the long term performance of fibre reinforced cementitious composites (FRC) exposed to climate stresses. Some of the most important results have been brought together in this...

  17. Theoretical studies of field-reversed configurations (FRC) and experimental study of the FRC during translation

    International Nuclear Information System (INIS)

    Siemon, R.E.; Armstrong, W.T.; Chrien, R.E.

    1985-01-01

    Theoretical studies of FRC stability and transport are summarized. Finite Larmor radius theories are shown to be unreliable for explaining the experimentally observed stability to tilting. Control of the n=2 rotational instability has been demonstrated in two-dimensional hybrid code simulations, and the stability appears to be described within MHD if the nearly square equilibria that result from quadrupole fields are taken into account. Simulations of the lower hybrid drift instability in parameter regimes relevant to experiments show good agreement with a non-local theory of the instability. A 1.5-dimensional transport code shows agreement with the energy confinement time but disagreement with the flux loss time observed in FRX-C. The process of FRC translation in which the plasma is formed, translated into a DC solenoid and trapped by magnetic mirrors, has been studied in the FRX-C/T experiment. Efficient transfer of particles, energy and internal magnetic flux are observed with no enhancement of loss processes over in-situ FRC experiments. The axial velocity of the FRC can be estimated reasonably well with a simple model based on conservation of energy. Internal magnetic field probing during translation shows the expected structure of poloidal field and a complex distribution of generally weak toroidal fields. Measurements of radiated power indicate that radiation is a small fraction of the total plasma power loss (typically 8%). Translation has facilitated scaling studies of confinement over a wider range of parameters than were achieved by in-situ FRX-C experiments. For example, the variable xsub(s), the ratio of the separatrix radius to the metal wall radius, has been increased to about 0.7 by allowing the FRC to expand during translation. In all cases, particle confinement times agree within a factor of two with predictions by models that assume a lower hybrid drift resistivity. However, for the conditions studied there are indications that the experimental

  18. On Early Age Crack Formation in FRC Slabs

    DEFF Research Database (Denmark)

    Olesen, John Forbes; Stang, Henrik

    1997-01-01

    The problem of early age crack formation in FRC slabs due to restrained temperature and shrinkage deformations, is given an analytical treatment. A model taking into account the ageing properties of the tensile softening curve and the continued development in the temperature and shrinkage...... deformations after crack initiation, is presented. Based on this model a design strategy for FRC slabs is outlined....

  19. Seismic Behaviour of Synthetic-Frc Columns

    Science.gov (United States)

    Paultre, P.; Eid, R.

    2017-09-01

    Inclusion of short discrete fibres into the concrete mixture can increase the compressive strength and ductility of normal-strength concrete (NSC) and high-strength concrete (HSC) column specimens under compressive loading as already has been shown by several studies. Concrete design codes ensure ductile behaviour of columns by setting a requirement for a minimum amount of transverse steel reinforcement. Therefore, the inclusion of discrete short fibres into the concrete mixture combined with a reduced amount of lateral reinforcement can be an alternative to the latter full amount required by the codes. This paper presents tests that were performed on large-scale fibre-reinforced NSC circular columns under cyclic flexure and constant axial load simulating earthquake loading. The aim of this test program is to examine the combined confinement effect of steel or synthetic fibres and the transverse steel reinforcement type (spirals or hoops) on the structural performance of RC columns. The results show that in terms of ductility and energy dissipation, the behaviour of the fibre-reinforced concrete (FRC) specimens is improved compared to the nonfibrous ones. This behaviour is also predicted by the proposed confinement model which takes into account the mechanical and the geometrical properties of the concrete and the reinforcement as well as those of the fibres.

  20. Development of Fracture Energy of FRC Materials. Freeze-Thaw Resistance of FRC Materials

    DEFF Research Database (Denmark)

    Stoklund Larsen, E.

    in this SBI Bulletin in order to give more direct information about two of the most important aspects in connection with FRCs. The SBI Bulletin contains two oral presentations given at the Fourth RILEM International Symposium on Fibre Reinforced Cement and Concrete which was held at the University......During the past four years research has been carried out at the Danish Building Research Institute on different aspects of the long term performance of fibre reinforced cementitious composites (FRC) exposed to climate stresses. Some of the most important results have been brought together...

  1. Optimal Path Choice in Railway Passenger Travel Network Based on Residual Train Capacity

    Directory of Open Access Journals (Sweden)

    Fei Dou

    2014-01-01

    Full Text Available Passenger’s optimal path choice is one of the prominent research topics in the field of railway passenger transport organization. More and more different train types are available, increasing path choices from departure to destination for travelers are unstoppable. However, travelers cannot avoid being confused when they hope to choose a perfect travel plan based on various travel time and cost constraints before departure. In this study, railway passenger travel network is constructed based on train timetable. Both the generalized cost function we developed and the residual train capacity are considered to be the foundation of path searching procedure. The railway passenger travel network topology is analyzed based on residual train capacity. Considering the total travel time, the total travel cost, and the total number of passengers, we propose an optimal path searching algorithm based on residual train capacity in railway passenger travel network. Finally, the rationale of the railway passenger travel network and the optimal path generation algorithm are verified positively by case study.

  2. Optimal path choice in railway passenger travel network based on residual train capacity.

    Science.gov (United States)

    Dou, Fei; Yan, Kai; Huang, Yakun; Wang, Li; Jia, Limin

    2014-01-01

    Passenger's optimal path choice is one of the prominent research topics in the field of railway passenger transport organization. More and more different train types are available, increasing path choices from departure to destination for travelers are unstoppable. However, travelers cannot avoid being confused when they hope to choose a perfect travel plan based on various travel time and cost constraints before departure. In this study, railway passenger travel network is constructed based on train timetable. Both the generalized cost function we developed and the residual train capacity are considered to be the foundation of path searching procedure. The railway passenger travel network topology is analyzed based on residual train capacity. Considering the total travel time, the total travel cost, and the total number of passengers, we propose an optimal path searching algorithm based on residual train capacity in railway passenger travel network. Finally, the rationale of the railway passenger travel network and the optimal path generation algorithm are verified positively by case study.

  3. Determination of functional residual capacity with 133-xenon radiospirometry. Comparison with body plethysmography and helium spirometry. Effect of body position

    International Nuclear Information System (INIS)

    Kauppinen-Walin, K.; Sovijaervi, A.R.A.; Muittari, A.; Uusitalo, A.

    1980-01-01

    The accuracy of 133-xenon radiospirometry for determination of FRC in healthy subjects was studied. Forty volunteers, both smokers and non-smokers, were examined. The FRC of each subject was concurrently determined with radiospirometric, He-dilution in closed circuit, and body plethysmographic methods. The mean FRC measured by radiospirometry (FRCsub(RS)) was 0.72 1 larger than that measured by helium spirometry (FRCsub(He)) in sitting position (P<0.01). In supine position the FRCsub(RS) was 0.65 1 larger than the FRCsub(He) (P<0.01). The body plethysmography (sitting position) gave FRC (TGV) 0.35 1 larger than the FRCsub(He) sitting (P<0.01). The FRCsub(He) and the FRCsub(RS) in the sitting position were 0.48 and 0.55 1 larger than in the supine position (P<0.01), respectively. Trapped air correlated significantly (P<0.01) with the difference FRCsub(RS) - FRCsub(He), when sitting. The results indicated that the FRC determined radiospirometrically is significantly larger than the FRC determined with He-spirometry. The difference is systematic, suggesting that it is caused by 133-xenon dissolved in blood and accumulated in tissues of the thoracic cage and by dissimilar representation of trapped air in FRCsub(RS) and FRCsub(He). After correction for systematic error, the FRC obtained as a by-product of radiospirometry may be used. (author)

  4. Recent FRC translation experiments on FRX-C/T

    International Nuclear Information System (INIS)

    Rej, D.J.; Armstrong, W.T.; Chrien, R.E.; Hugrass, W.N.; Klingner, P.L.; McKenna, K.F.; Sherwood, E.G.; Siemon, R.E.; Tuszewski, M.

    1985-01-01

    Since the last CT Symposium, several accomplishments have been realized from the FRC translation studies on the FRX-C/T device: (1) FRCs have been launched into, and trapped in, a dc magnetic guide field region without the use of any pulsed ''gate'' coils; (2) detailed studies of translation dynamics have been performed which are consistent with energy conservation, adiabatic compression theory, and 2-D MHD simulations; (3) the confinement properties of translated FRC has been evaluated; (4) translation through either puff or static deuterium gas fill has been demonstrated; (5) higher density (n less than or equal to 4 x 10 15 cm -3 ) FRCs have been translated over 10-m lengths; (6) the n = 2 rotational instability has been stabilized by FRC translation into a weak helical quadrupole field

  5. Simulations of a Plasma Thruster Utilizing the FRC Configuration

    Energy Technology Data Exchange (ETDEWEB)

    Rognlien, T. D. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Cohen, B. I. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

    2016-10-10

    This report describes work performed by LLNL to model the behavior and performance of a reverse-field configuration (FRC) type of plasma device as a plasma thruster as summarized by Razin et al. [1], which also describes the MNX device at PPPL used to study this concept.

  6. An adsorbent with a high adsorption capacity obtained from the cellulose sludge of industrial residues.

    Science.gov (United States)

    Orlandi, Géssica; Cavasotto, Jéssica; Machado, Francisco R S; Colpani, Gustavo L; Magro, Jacir Dal; Dalcanton, Francieli; Mello, Josiane M M; Fiori, Márcio A

    2017-02-01

    One of the major problems in effluent treatment plants of the cellulose and paper industry is the large amount of residual sludge generated. Therefore, this industry is trying to develop new methods to treat such residues and to use them as new products, such as adsorbents. In this regard, the objective of this work was to develop an adsorbent using the raw activated sludge generated by the cellulose and paper industry. The activated cellulose sludge, after being dried, was chemically activated with 42.5% (v/v) phosphoric acid at 85 °C for 1 h and was charred at 500 °C, 600 °C and 700 °C for 2 h. The efficiency of the obtained adsorbent materials was evaluated using kinetic tests with methylene blue solutions. Using the adsorption kinetics, it was verified that the three adsorbents showed the capacity to adsorb dye, and the adsorbent obtained at a temperature of 600 °C showed the highest adsorption capacity of 107.1 mg g -1 . The kinetic model that best fit the experimental data was pseudo-second order. The Langmuir-Freudlich isotherm adequately described the experimental data. As a result, the cellulose sludge generated by the cellulose and paper industries could be used as an adsorbent. Copyright © 2016 Elsevier Ltd. All rights reserved.

  7. Residual attentional capacity amongst young and elderly during dual and triple task walking

    DEFF Research Database (Denmark)

    Læssøe, Uffe; Hoeck, Hans C.; Simonsen, Ole

    2008-01-01

    to the cognitive task the elderly increased their temporal stride-to-stride variability by 39% in the walking task and by 57% in the combined motor task. These increases were significantly larger than observed for the young. Equivalent decreases in trunk acceleration autocorrelation coefficients and gait speed...... in the study. The participants walked along a figure-of-eight track at a self-selected speed. The effect of introducing a concurrent cognitive task and a concurrent functional motor task was evaluated. Stride-to-stride variability was measured by heel contacts and by trunk accelerometry. In response...... were found. A combination of sufficiently challenging motor tasks and concurrent cognitive tasks can reveal signs of limited residual attentional capacity during walking amongst the elderly....

  8. Load-Bearing Capacity of Fiber-Reinforced Composite Abutments and One-Piece Implants.

    Science.gov (United States)

    Etxeberria, Marina; Abdulmajeed, Aous A; Escuin, Tomas; Vinas, Miguel; Lassila, Lippo V J; Närhi, Timo O

    2015-06-01

    Fiber-reinforced composites (FRC) can potentially help in a physiologic stress transmission due to its excellent biomechanical matching with living tissues. Novel one-piece FRC implants and abutments with two different fiber orientations were loaded until failure to assess the load-bearing capacity, fracture patterns, and precision of fit. The one-piece FRC implants showed significantly higher load-bearing capacity compared to FRC abutments regardless of the fiber orientation (p < 0.001). For FRC abutments, bidirectional abutments showed significantly higher loads compared to unidirectional abutments (p < 0.001). The type of structure and fiber orientation are strong determinant factors of the load-bearing capacity of FRC implants and abutments.

  9. Influence of the inherent properties of drinking water treatment residuals on their phosphorus adsorption capacities.

    Science.gov (United States)

    Bai, Leilei; Wang, Changhui; He, Liansheng; Pei, Yuansheng

    2014-12-01

    Batch experiments were conducted to investigate the phosphorus (P) adsorption and desorption on five drinking water treatment residuals (WTRs) collected from different regions in China. The physical and chemical characteristics of the five WTRs were determined. Combined with rotated principal component analysis, multiple regression analysis was used to analyze the relationship between the inherent properties of the WTRs and their P adsorption capacities. The results showed that the maximum P adsorption capacities of the five WTRs calculated using the Langmuir isotherm ranged from 4.17 to 8.20mg/g at a pH of 7 and further increased with a decrease in pH. The statistical analysis revealed that a factor related to Al and 200 mmol/L oxalate-extractable Al (Alox) accounted for 36.5% of the variations in the P adsorption. A similar portion (28.5%) was attributed to an integrated factor related to the pH, Fe, 200 mmol/L oxalate-extractable Fe (Feox), surface area and organic matter (OM) of the WTRs. However, factors related to other properties (Ca, P and 5 mmol/L oxalate-extractable Fe and Al) were rejected. In addition, the quantity of P desorption was limited and had a significant negative correlation with the (Feox+Alox) of the WTRs (p<0.05). Overall, WTRs with high contents of Alox, Feox and OM as well as large surface areas were proposed to be the best choice for P adsorption in practical applications. Copyright © 2014. Published by Elsevier B.V.

  10. Merging formation of FRC and its application to high-beta ST formation

    International Nuclear Information System (INIS)

    Ono, Y.; Inomoto, M.; Ueda, Y.; Matsuyama, T.; Ohshima, Y.; Katsurai, M.

    2001-01-01

    Merging formation of field-reversed configuration (FRC) explored not only a new scenario of highly-efficient FRC formation/amplification experiment but also a new boundary research between FRC, spheromak and spherical tokamak (ST). A new finding is that the produced FRC is transformed stably into an ultra-high-β ST by applying external toroidal field B t,ext . The toroidal field was observed to vanish around magnetic axis after the B t,ext application to the FRC, indicating formation of diamagnetic ST. The hollow current profile of FRC was maintained during the equilibrium transition, eliminating a need for the difficult hollow-current-formation process of start-up discharge of high-β ST. The energy-conversion effect of merging transformed the force-free merging spheromaks with paramagnetic current into the FRC with diamagnetic current and the further application of B t,ext did the FRC into the ultra-high-β (>60%)/diamagnetic ST, indicating the close relationship between FRC and ST in second stability. (author)

  11. Influence of bending test configuration on cracking behavior of FRC

    DEFF Research Database (Denmark)

    Finazzi, Silvia; Paegle, Ieva; Fischer, Gregor

    2014-01-01

    This paper describes an investigation of the influence of the testing configuration for Fiber Reinforced Concrete in bending and aims at evaluating the influence of the test configuration details on the characterization of the material. Two different types of FRC, Steel Fiber Reinforced Concrete...... (SFRC) and Engineered Cementitious Composites (ECC), were tested and are described in this study. The materials were chosen so that one of them would be strain hardening (ECC) and the other tension softening (SFRC). Notched and un-notched three- and four-point bending tests were carried out to determine...

  12. Design Basis for Fibre Reinforced Concrete (FRC) Pavements

    DEFF Research Database (Denmark)

    Bendixen, Søren; Stang, Henrik

    1996-01-01

    opening relationship can beused to descibe the properties of fibre reinforced concrete (FRC) intension and how the stress-crack opening relationship can beapplied in a simple design scheme for pavements. The projectincludes development of design tools, experiments to determine thestress-crack opening......The paper summarises a Ph.D. project on development of a new design basis for fibre reinforced concrete ground slabs. The stress-crack openingrelationship is a well know basic material property of theso-called fictitious crack model for concrete. In the presentstudy it is shown how the stress-crack...

  13. Nutrient removal capacity of wood residues for the Agro-environmental safety of ground and surface waters

    Directory of Open Access Journals (Sweden)

    Paulo A. Dumont

    2014-07-01

    Full Text Available The aim of this study was to determine the effectiveness of wood residues in the removal of nutrients (ammonium-N; NH4-N from nutrient-rich (NH4-N waters. The water holding capacity of the wood materials was also determined. Carried out at Rothamsted Research, North Wyke, UK, this controlled laboratory experiment tested two wood residues; in length, one being 1-2cm and the other from 150 µm (microns to 9.5mm. Although a wide range of studies have shown the effectiveness and performance of various absorbent materials as animal beddings, such as straw (cereal straw, woodchip (sawdust, bark or wood shavings, bracken and rushes, only few have focused on the NH4-N sorption/desorption capacity. The depuration capacity of wood residues from nutrient-rich effluents such as those from cattle bedded on woodchip or straw will be controlled by processes such as sorption (adsorption-absorption and desorption of nutrients. Studies have reported the nitrogen removal capacity of woodchip materials and biochar from woodchip as well as removal of NH4+-N from domestic and municipal wastewater, farm dirty water, landfill and industry effluents. These studies have observed that the mechanism of removal of nitrogen is by either increasing NO3--N removal form leachate by enhancing N2O losses via denitrification (biochar as carbon source for denitrifiers or by decreasing NH4+-N in leachate through adsorption to negatively charged sites. Results showed that although the cation exchange capacity (CEC and surface area (SA are both fundamental properties of adsorbent materials, no correlation was found with CEC and adsorption or desorption. Nor did changes in pH appear to be sufficiently important to cause changes in CEC. For this reason, osmotic pressure appeared to be a more predominant parameter controlling processes of adsorption and desorption of NH4+-N in both wood residues. Thus, wood residues high in NH4+-N should be avoided, as they could have an opposite effect

  14. Nonlinear and Non-ideal Effects on FRC Stability

    International Nuclear Information System (INIS)

    Belova, E.V.; Davidson, R.C.; Ji, H.; Yamada, M.

    2002-01-01

    New computational results are presented which advance the understanding of the stability properties of the Field-Reversed Configuration (FRC). We present results of hybrid and two-fluid (Hall-MHD) simulations of prolate FRCs in strongly kinetic and small-gyroradius, MHD-like regimes. The n = 1 tilt instability mechanism and stabilizing factors are investigated in detail including nonlinear and resonant particle effects, particle losses along the open field lines, and Hall stabilization. It is shown that the Hall effect determines the mode rotation and change in the linear mode structure in the kinetic regime; however, the reduction in the growth rate is mostly due to the finite Larmor radius effects. Resonant particle effects are important in the large gyroradius regime regardless of the separatrix shape, and even in cases when a large fraction of the particle orbits are stochastic. Particle loss along the open field lines has a destabilizing effect on the tilt mode and contributes to the ion spin up in toroidal direction. The nonlinear evolution of unstable modes in both kinetic and small-gyroradius FRCs is shown to be considerably slower than that in MHD simulations. Our simulation results demonstrate that a combination of kinetic and nonlinear effects is a key for understanding the experimentally observed FRC stability properties

  15. Hyperactivity, startle reactivity and cell-proliferation deficits are resistant to chronic lithium treatment in adult Nr2e1(frc/frc) mice.

    Science.gov (United States)

    Wong, B K Y; Hossain, S M; Trinh, E; Ottmann, G A; Budaghzadeh, S; Zheng, Q Y; Simpson, E M

    2010-10-01

    The NR2E1 region on Chromosome 6q21-22 has been repeatedly linked to bipolar disorder (BP) and NR2E1 has been associated with BP, and more specifically bipolar I disorder (BPI). In addition, patient sequencing has shown an enrichment of rare candidate-regulatory variants. Interestingly, mice carrying either spontaneous (Nr2e1(frc) ) or targeted (Tlx(-) ) deletions of Nr2e1 (here collectively known as Nr2e1-null) show similar neurological and behavioral anomalies, including hypoplasia of the cerebrum, reduced neural stem cell proliferation, extreme aggression and deficits in fear conditioning; these are the traits that have been observed in some patients with BP. Thus, NR2E1 is a positional and functional candidate for a role in BP. However, no Nr2e1-null mice have been fully evaluated for behaviors used to model BP in rodents or pharmacological responses to drugs effective in treating BP symptoms. In this study we examine Nr2e1(frc/frc) mice, homozygous for the spontaneous deletion, for abnormalities in activity, learning and information processing, and cell proliferation; these are the phenotypes that are either affected in patients with BP or commonly assessed in rodent models of BP. The effect of lithium, a drug used to treat BP, was also evaluated for its ability to attenuate Nr2e1(frc/frc) behavioral and neural stem cell-proliferation phenotypes. We show for the first time that Nr2e1-null mice exhibit extreme hyperactivity in the open field as early as postnatal day 18 and in the home cage, deficits in open-field habituation and passive avoidance, and surprisingly, an absence of acoustic startle. We observed a reduction in neural stem/progenitor cell proliferation in Nr2e1(frc/frc) mice, similar to that seen in other Nr2e1-null strains. These behavioral and cell-proliferation phenotypes were resistant to chronic-adult-lithium treatment. Thus, Nr2e1(frc/frc) mice exhibit behavioral traits used to model BP in rodents, but our results do not support Nr2e1(frc/frc

  16. Enhancement of methylbenzene adsorption capacity through cetyl trimethyl ammonium bromide-modified activated carbon derived from Astragalus residue

    Science.gov (United States)

    Feng, Ningchuan; Zhang, Yumei; Fan, Wei; Zhu, Meilin

    2018-02-01

    Activated carbon was prepared from astragalus residue by KOH and then treated with cetyl trimethyl ammonium bromide (CTAB) and used for the removal of methylbenzene from aqueous solution. The samples were characterized by FTIR, XRD, SEM and Boehm titration. The results showed that CTAB changed the physicochemical properties of activated carbon significantly. The isotherm adsorption studies of methylbenzene onto the astragalus residue activated carbon (ASC) and CTAB-modified astragalus residue activated carbon (ASCCTAB) were examined by using batch techniques and agreed well with the Langmuir model. The maximum adsorption capacity of ASC and ASC-CTAB for methylbenzene determined from the Langmuir model was183.56 mg/g and 235.18 mg/g, respectively. The results indicated that using CTAB as a modifier for ASC modification could markedly enhance the methylbenzene removal from water.

  17. Assessment of Potential Capacity Increases at Combined Heat and Power Facilities Based on Available Corn Stover and Forest Logging Residues

    Directory of Open Access Journals (Sweden)

    Donald L. Grebner

    2013-08-01

    Full Text Available Combined Heat and Power (CHP production using renewable energy sources is gaining importance because of its flexibility and high-energy efficiency. Biomass materials, such as corn stover and forestry residues, are potential sources for renewable energy for CHP production. In Mississippi, approximately 4.0 MT dry tons of woody biomass is available annually for energy production. In this study, we collected and analyzed 10 years of corn stover data (2001–2010 and three years of forest logging residue data (1995, 1999, and 2002 in each county in Mississippi to determine the potential of these feed stocks for sustainable CHP energy production. We identified six counties, namely Amite, Copiah, Clarke, Wayne, Wilkinson and Rankin, that have forest logging residue feedstocks to sustain a CHP facility with a range of capacity between 8.0 and 9.8 MW. Using corn stover alone, Yazoo and Washington counties can produce 13.4 MW and 13.5 MW of energy, respectively. Considering both feedstocks and based on a conservative amount of 30% available forest logging residue and 33% corn stover, we found that 20 counties have adequate supply for a CHP facility with a capacity of 8.3 MW to 19.6 MW.

  18. Scaling of FRC Thrusters with Neutral Entrainment (Conference Paper with Briefing Charts)

    Science.gov (United States)

    2016-12-09

    Conference Paper with Briefing Charts 3. DATES COVERED (From - To) 13 October 2016 – 09 December 2016 4. TITLE AND SUBTITLE Scaling of FRC Thrusters...developed to evaluate the performance enhancement of neutral entrainment on an EP system, and to determine physical scaling laws to be leveraged in...Number 16511 1 Scaling of FRC Thrusters with Neutral Entrainment Justin Little, Barry Cornella, Anthony Pancotti, and David Kirtley MSNW LLC

  19. FRC plasma studies on the FRX-L plasma injector for MTF

    International Nuclear Information System (INIS)

    Wurden, G.A.; Intrator, T.P.; Zhang, S.Y.; Furno, I.G.; Hsu, S.C.; Park, J.Y.; Kirkpatrick, R.; Renneke, R.M.; Schoenberg, K.F.; Taccetti, M.J.; Tuszewski, M.G.; Waganaar, W.J.; Zhehui Wang; Siemon, R.E.; Degnan, J.H.; Gale, D.G.; Grabowski, C.; Ruden, E.L.; Sommars, W.; Frese, M.H.; Coffey, S.; Craddock, G.; Frese, S.D.; Roderick, N.F.

    2005-01-01

    To demonstrate the physics basis for Magnetized Target Fusion (MTF), we have designed a field reversed configuration (FRC) target plasma to ultimately be compressed within an imploding metal flux conserver (liner). This new, high energy density FRC device, named FRX-L, is operating at Los Alamos as a compact 'theta-pinch' formation FRC. The system capability includes a 0.5 T bias field, 70 kV 250 kHz ringing pre-ionization, and a 1.5 MA, 200 kJ main-theta-coil bank. We show FRC data with plasma parameters approaching the desired MTF requirements, examples of substantial Ohmic heating from magnetic flux annihilation, and measurements of plasma anomalous resistivity. Improvements are underway to reduce the main bank crowbar ringing, which will increase the trapped flux in the FRC. A prototype deformable flux-conserving liner with large entrance holes to accept an FRC has also been designed with MACH2 (2-D MHD modelling code) and successfully imploded at Kirtland Air Force Base on the Shiva Star pulsed power facility. (author)

  20. The Prognostic Value of Residual Volume/Total Lung Capacity in Patients with Chronic Obstructive Pulmonary Disease.

    Science.gov (United States)

    Shin, Tae Rim; Oh, Yeon-Mok; Park, Joo Hun; Lee, Keu Sung; Oh, Sunghee; Kang, Dae Ryoung; Sheen, Seungsoo; Seo, Joon Beom; Yoo, Kwang Ha; Lee, Ji-Hyun; Kim, Tae-Hyung; Lim, Seong Yong; Yoon, Ho Il; Rhee, Chin Kook; Choe, Kang-Hyeon; Lee, Jae Seung; Lee, Sang-Do

    2015-10-01

    The prognostic role of resting pulmonary hyperinflation as measured by residual volume (RV)/total lung capacity (TLC) in chronic obstructive pulmonary disease (COPD) remains poorly understood. Therefore, this study aimed to identify the factors related to resting pulmonary hyperinflation in COPD and to determine whether resting pulmonary hyperinflation is a prognostic factor in COPD. In total, 353 patients with COPD in the Korean Obstructive Lung Disease cohort recruited from 16 hospitals were enrolled. Resting pulmonary hyperinflation was defined as RV/TLC ≥ 40%. Multivariate logistic regression analysis demonstrated that older age (P = 0.001), lower forced expiratory volume in 1 second (FEV1) (P pulmonary hyperinflation in COPD. RV/TLC is an independent risk factor for all-cause mortality in COPD.

  1. Neurophysiological Indicators of Residual Cognitive Capacity in the Minimally Conscious State

    Directory of Open Access Journals (Sweden)

    Solveig L. Hauger

    2015-01-01

    Full Text Available Background. The diagnostic usefulness of electrophysiological methods in assessing disorders of consciousness (DoC remains to be established on an individual patient level, and there is need to determine what constitutes robust experimental paradigm to elicit electrophysiological indices of covert cognitive capacity. Objectives. Two tasks encompassing active and passive conditions were explored in an event-related potentials (ERP study. The task robustness was studied in healthy controls, and their utility to detect covert signs of command-following on an individual patient level was investigated in patients in a minimally conscious state (MCS. Methods. Twenty healthy controls and 20 MCS patients participated. The active tasks included (1 listening for a change of pitch in the subject’s own name (SON and (2 counting SON, both contrasted to passive conditions. Midline ERPs are reported. Results. A larger P3 response was detected in the counting task compared to active listening to pitch change in the healthy controls. On an individual level, the counting task revealed a higher rate of responders among both healthy subjects and MCS patients. Conclusion. ERP paradigms involving actively counting SON represent a robust paradigm in probing for volitional cognition in minimally conscious patients and add important diagnostic information in some patients.

  2. Spot-Bonding and Full-Bonding Techniques for Fiber Reinforced Composite (FRC) and Metallic Retainers

    Science.gov (United States)

    Gandini, Paola; Tessera, Paola; Vallittu, Pekka K.; Lassila, Lippo; Sfondrini, Maria Francesca

    2017-01-01

    Fiber reinforced Composite (FRC) retainers have been introduced as an aesthetic alternative to conventional metallic splints, but present high rigidity. The purpose of the present investigation was to evaluate bending and fracture loads of FRC splints bonded with conventional full-coverage of the FRC with a composite compared with an experimental bonding technique with a partial (spot-) resin composite cover. Stainless steel rectangular flat, stainless steel round, and FRC retainers were tested at 0.2 and 0.3 mm deflections and at a maximum load. Both at 0.2 and 0.3 mm deflections, the lowest load required to bend the retainer was recorded for spot-bonded stainless steel flat and round wires and for spot-bonded FRCs, and no significant differences were identified among them. Higher force levels were reported for full-bonded metallic flat and round splints and the highest loads were recorded for full-bonded FRCs. At the maximum load, no significant differences were reported among spot- and full-bonded metallic splints and spot-bonded FRCs. The highest loads were reported for full bonded FRCs. The significant decrease in the rigidity of spot-bonded FRC splints if compared with full-bonded retainers suggests further tests in order to propose this technique for clinical use, as they allow physiologic tooth movement, thus presumably reducing the risk of ankylosis. PMID:28976936

  3. Spot-Bonding and Full-Bonding Techniques for Fiber Reinforced Composite (FRC and Metallic Retainers

    Directory of Open Access Journals (Sweden)

    Andrea Scribante

    2017-10-01

    Full Text Available Fiber reinforced Composite (FRC retainers have been introduced as an aesthetic alternative to conventional metallic splints, but present high rigidity. The purpose of the present investigation was to evaluate bending and fracture loads of FRC splints bonded with conventional full-coverage of the FRC with a composite compared with an experimental bonding technique with a partial (spot- resin composite cover. Stainless steel rectangular flat, stainless steel round, and FRC retainers were tested at 0.2 and 0.3 mm deflections and at a maximum load. Both at 0.2 and 0.3 mm deflections, the lowest load required to bend the retainer was recorded for spot-bonded stainless steel flat and round wires and for spot-bonded FRCs, and no significant differences were identified among them. Higher force levels were reported for full-bonded metallic flat and round splints and the highest loads were recorded for full-bonded FRCs. At the maximum load, no significant differences were reported among spot- and full-bonded metallic splints and spot-bonded FRCs. The highest loads were reported for full bonded FRCs. The significant decrease in the rigidity of spot-bonded FRC splints if compared with full-bonded retainers suggests further tests in order to propose this technique for clinical use, as they allow physiologic tooth movement, thus presumably reducing the risk of ankylosis.

  4. Spot-Bonding and Full-Bonding Techniques for Fiber Reinforced Composite (FRC) and Metallic Retainers.

    Science.gov (United States)

    Scribante, Andrea; Gandini, Paola; Tessera, Paola; Vallittu, Pekka K; Lassila, Lippo; Sfondrini, Maria Francesca

    2017-10-04

    Fiber reinforced Composite (FRC) retainers have been introduced as an aesthetic alternative to conventional metallic splints, but present high rigidity. The purpose of the present investigation was to evaluate bending and fracture loads of FRC splints bonded with conventional full-coverage of the FRC with a composite compared with an experimental bonding technique with a partial (spot-) resin composite cover. Stainless steel rectangular flat, stainless steel round, and FRC retainers were tested at 0.2 and 0.3 mm deflections and at a maximum load. Both at 0.2 and 0.3 mm deflections, the lowest load required to bend the retainer was recorded for spot-bonded stainless steel flat and round wires and for spot-bonded FRCs, and no significant differences were identified among them. Higher force levels were reported for full-bonded metallic flat and round splints and the highest loads were recorded for full-bonded FRCs. At the maximum load, no significant differences were reported among spot- and full-bonded metallic splints and spot-bonded FRCs. The highest loads were reported for full bonded FRCs. The significant decrease in the rigidity of spot-bonded FRC splints if compared with full-bonded retainers suggests further tests in order to propose this technique for clinical use, as they allow physiologic tooth movement, thus presumably reducing the risk of ankylosis.

  5. Formation and sustainment of field reversed configuration (FRC) plasmas by spheromak merging and neutral beam injection

    Energy Technology Data Exchange (ETDEWEB)

    Yamada, Masaaki [Princeton Plasma Physics Laboratory, Princeton University Princeton, New Jersey USA (United States)

    2016-03-25

    This paper briefly reviews a compact toroid reactor concept that addresses critical issues for forming, stabilizing and sustaining a field reversed configuration (FRC) with the use of plasma merging, plasma shaping, conducting shells, neutral beam injection (NBI). In this concept, an FRC plasma is generated by the merging of counter-helicity spheromaks produced by inductive discharges and sustained by the use of neutral beam injection (NBI). Plasma shaping, conducting shells, and the NBI would provide stabilization to global MHD modes. Although a specific FRC reactor design is outside the scope of the present paper, an example of a promising FRC reactor program is summarized based on the previously developed SPIRIT (Self-organized Plasmas by Induction, Reconnection and Injection Techniques) concept in order to connect this concept to the recently achieved the High Performance FRC plasmas obtained by Tri Alpha Energy [Binderbauer et al, Phys. Plasmas 22,056110, (2015)]. This paper includes a brief summary of the previous concept paper by M. Yamada et al, Plasma Fusion Res. 2, 004 (2007) and the recent experimental results from MRX.

  6. Overview of C-2U FRC Experimental Program and Plans for C-2W

    Science.gov (United States)

    Gota, H.; Binderbauer, M. W.; Tajima, T.; Putvinski, S.; Tuszewski, M.; Dettrick, S.; Korepanov, S.; Smirnov, A.; Thompson, M. C.; Yang, X.; Cappello, M.; Ivanov, A. A.; TAE Team

    2016-10-01

    Tri Alpha Energy's experimental program has been focused on a demonstration of reliable field-reversed configuration (FRC) formation and sustainment, driven by fast ions via high-power neutral-beam (NB) injection. The world's largest compact-toroid experimental devices, C-2 and C-2U, have successfully produced a well-stabilized, sustainable FRC plasma state with NB injection (input power, PNB 10 + MW; 15 keV hydrogen) and end-on coaxial plasma guns. Remarkable improvements in confinement and stability of FRC plasmas have led to further improved fast-ion build up; thereby, an advanced beam-driven FRC state has been produced and sustained for up to 5 + ms (longer than all characteristic system time scales), only limited by hardware and electric supply constraints such as NB and plasma-gun power supplies. To further improve the FRC performance the C-2U device is being replaced by C-2W featuring higher injected NB power, longer pulse duration as well as enhanced edge-biasing systems and substantially upgraded divertors. Main C-2U experimental results and key features of C-2W will be presented. Tri Alpha Energy, Inc.

  7. Polder effects on sediment-to-soil conversion: water table, residual available water capacity, and salt stress interdependence.

    Science.gov (United States)

    Radimy, Raymond Tojo; Dudoignon, Patrick; Hillaireau, Jean Michel; Deboute, Elise

    2013-01-01

    The French Atlantic marshlands, reclaimed since the Middle Age, have been successively used for extensive grazing and more recently for cereal cultivation from 1970. The soils have acquired specific properties which have been induced by the successive reclaiming and drainage works and by the response of the clay dominant primary sediments, that is, structure, moisture, and salinity profiles. Based on the whole survey of the Marais Poitevin and Marais de Rochefort and in order to explain the mechanisms of marsh soil behavior, the work focuses on two typical spots: an undrained grassland since at least 1964 and a drained cereal cultivated field. The structure-hydromechanical profiles relationships have been established thanks to the clay matrix shrinkage curve. They are confronted to the hydraulic functioning including the fresh-to-salt water transfers and to the recording of tensiometer profiles. The CE1/5 profiles supply the water geochemical and geophysical data by their better accuracy. Associated to the available water capacity calculation they allow the representation of the parallel evolution of the residual available water capacity profiles and salinity profiles according to the plant growing and rooting from the mesophile systems of grassland to the hygrophile systems of drained fields.

  8. Geological Engineering Characteristics of the Residual Soil: Implementation for Soil Bearing Capacity at Gayungan, Surabaya, East Java

    Science.gov (United States)

    Rukmana, Y. Y.; Ridwan, M.

    2018-01-01

    This paper presents the results of soil investigation on the residual soil at Gayungan Surabaya. The methodology of the research consists of Drilling + Standard Penetration Test (ASTM D1586-99), sampling and laboratory test for index properties & mechanical of soil, then analyzed for Soil Bearing Capacity (Meyerhoff, 1976). Field test analysis data showed that Bore Hole.01(BH.01) and Bore Hole.03 (BH.03) were dominated by Sand / Sandy clay layer with Standart Penetration Test (SPT) values: 6-68, whereas in BH.02 was dominated by Clayey sand layer with Standard Penetration Test (SPT) values: 32-68. Based on Soil classification according to Unified Soil Classification System (USCS), the soil type at the research area consisted of ML (Silt with Low plasticity), CL ( Clay with low plasticity), MH (Silt with High plasticity), and SP (Sand with Poor gradation). Based on the borlog data and soil bearing capacity analysis of the research area is recommended: for The Deep foundation to reaches at least 16 meters depth with Qa = 1160.40-2032.80 kN / m2, and Shallow foundation reaches at least 1-2 meters deep with Qa = 718.25 kN / M2.

  9. Polder Effects on Sediment-to-Soil Conversion: Water Table, Residual Available Water Capacity, and Salt Stress Interdependence

    Directory of Open Access Journals (Sweden)

    Raymond Tojo Radimy

    2013-01-01

    Full Text Available The French Atlantic marshlands, reclaimed since the Middle Age, have been successively used for extensive grazing and more recently for cereal cultivation from 1970. The soils have acquired specific properties which have been induced by the successive reclaiming and drainage works and by the response of the clay dominant primary sediments, that is, structure, moisture, and salinity profiles. Based on the whole survey of the Marais Poitevin and Marais de Rochefort and in order to explain the mechanisms of marsh soil behavior, the work focuses on two typical spots: an undrained grassland since at least 1964 and a drained cereal cultivated field. The structure-hydromechanical profiles relationships have been established thanks to the clay matrix shrinkage curve. They are confronted to the hydraulic functioning including the fresh-to-salt water transfers and to the recording of tensiometer profiles. The CE1/5 profiles supply the water geochemical and geophysical data by their better accuracy. Associated to the available water capacity calculation they allow the representation of the parallel evolution of the residual available water capacity profiles and salinity profiles according to the plant growing and rooting from the mesophile systems of grassland to the hygrophile systems of drained fields.

  10. Retention capacity of samarium (III) in zircon for it possible use in retaining walls for confinement of nuclear residues

    International Nuclear Information System (INIS)

    Garcia G, N.

    2006-01-01

    Mexico, as country that produces part of its electric power by nuclear means, should put special emphasis in the development of technologies guided to the sure and long term confinement of the high level nuclear residuals. This work studies the capacity that has the natural zircon to retain to the samarium (III) in solution, by what due, firstly, to characterize the zircon for technical instrumental to determine the purity and characteristic of the mineral in study. The instrumental techniques that were used to carry out the physicochemical characterization were the neutron activation analysis (NAA), the infrared spectroscopy (IS), the thermal gravimetric analysis (TGA), scanning electron microscopy (SEM), transmission electron microscopy (TEM), semiquantitative analysis, dispersive energy spectroscopy (EDS), X-ray diffraction (XRD) and luminescence technique. The characterization of the surface properties carries out by means of the determination of the surface area using the BET multipoint technique, acidity constants, hydration time, the determination of the point of null charge (pH PCN ) and density of surface sites (D s ). The luminescence techniques were useful to determine the optimal point hydration of the zircon and for the quantification of the samarium, for that here intends the development of both analysis techniques. With the adjustment of the titration curves in the FITEQL 4 package the constants of surface acidity in the solid/liquid interface were determined. To the finish of this study it was corroborated that the zircon is a mineral that presents appropriate characteristics to be proposed as a contention barrier for the deep geologic confinement. With regard to the study of adsorption that one carries out the samarium retention it is superior to 90% under the described conditions. This investigation could also be applicable in the confinement of dangerous industrial residuals. (Author)

  11. Exercise Training Improves Exercise Capacity and Quality of Life in Patients with Inoperable or Residual Chronic Thromboembolic Pulmonary Hypertension

    Science.gov (United States)

    Herb, Jochen; Ehlken, Nicola; Fischer, Christine; Reichenberger, Frank; Rosenkranz, Stephan; Seyfarth, Hans-Juergen; Mayer, Eckhard

    2012-01-01

    Background Aim of this prospective study was to evaluate the effects of exercise training in patients with inoperable or residual chronic thromboembolic pulmonary hypertension (CTEPH). Methods Thirty-five consecutive patients with invasively confirmed inoperable or residual CTEPH (16 women;19 men; mean age 61±15 years, mean pulmonary artery pressure, 63±20 mmHg; primary inoperable n = 33, persisting pulmonary hypertension after pulmonary endarterectomy n = 2) on stable disease-targeted medication received exercise training in-hospital for 3 weeks and continued at home for 15 weeks. Medication remained unchanged during the study period. Efficacy parameters have been evaluated at baseline, after 3 and 15 weeks by blinded-observers. Survival rate has been evaluated in a follow-up period of median 36.4 months (interquartile range 26.6–46.6 months). Results All patients tolerated exercise training without severe adverse events. Patients significantly improved the mean distance walked in 6 minutes compared to baseline by 61±54 meters after 3 weeks (p<0.001) and by 71±70 meters after 15 weeks (p = 0.001), as well as scores of quality-of-life questionnaire, peak oxygen consumption and maximal workload. NT-proBNP improved significantly after 3 weeks of exercise training (p = 0.046). The 1-year survival rate was 97%, 2-year survival rate was 94% and the 3-year-survival 86% respectively. Conclusion Training as add-on to medical therapy may be effective in patients with CTEPH to improve work capacity, quality of life and further prognostic relevant parameters and possibly improves the 1-, 2- and 3-year survival rate. Further multicentric randomized controlled studies are needed to confirm these promising results. Trial Registration ClinicalTrials.gov NCT01398345 PMID:22848542

  12. Phosphorus Sorption Capacity of Concrete Waste, Natural Sorbents, Alum Residuals from Water Supply Sludge, and Ceramic Material for Tertiary Treatment in Onsite Systems

    Directory of Open Access Journals (Sweden)

    Siriporn Larpkiattaworn

    2013-01-01

    Full Text Available The phosphorus (P sorption capacity was determined for concrete waste, alum residuals from water treatment sludge, and natural sorbents (shells, clay, kaolin, and mordenite from various parts of Thailand. The material showing the best P sorption capacity (shells was selected for preparing a ceramic material to support the growth of nitrifying bacteria. The ceramic material, consisting of shells (50% by weight, alum residuals sludge (40% by weight and a soil (10% by weight heat at 750°C for about one hour, was studied for its P sorption capacity. Langmuir and Freundlich sorption isotherms yielded similar relative maximum P sorption capacities for the sorbents. The results from the Langmuir calculations showed the following maximum P sorption capacities: 32.26 g P/Kg shells, 31.25 g P/Kg concrete waste, 7.19 g P/Kg alum residuals sludge, 290 mg P/Kg clay, 80 mg P/Kg kaolin, and 30 mg P/Kg mordenite. The P sorption capacity for the prepared ceramic material at grain size 12 mm was 4.85 g P/kg. This result suggests that the ceramic material could be used for P sorption while providing growth support for nitrifying bacteria, similar to the well documented a popular P sorption material: light expanded clay aggregate (LECA from Sweden.

  13. The influence of framework design on the load-bearing capacity of laboratory-made inlay-retained fibre-reinforced composite fixed dental prostheses

    NARCIS (Netherlands)

    Keulemans, F.; Lassilla, L.V.J.; Garoushi, S.; Vallittu, P.K.; Kleverlaan, C.J.; Feilzer, A.J.

    2009-01-01

    Delamination of the veneering composite is frequently encountered with fibre-reinforced composite (FRC) fixed dental prosthesis (FDPs). The aim of this study is to evaluate the influence of framework design on the load-bearing capacity of laboratory-made three-unit inlay-retained FRC-FDPs.

  14. A functional analysis of the formyl-coenzyme A (frc) gene from Lactobacillus reuteri 100-23C.

    Science.gov (United States)

    Kullin, B; Tannock, G W; Loach, D M; Kimura, K; Abratt, V R; Reid, S J

    2014-06-01

    To examine the role of the Lactobacillus reuteri 100-23C frc gene product in oxalate metabolism, host colonization and the acid stress response. Genes encoding putative formyl-CoA transferase (frc) and oxalyl-CoA decarboxylase (oxc) enzymes are present in the genome sequences of Lact. reuteri strains. Two strains isolated from humans harboured an IS200 insertion sequence in the frc ORF and a group 2 intron-associated transposase downstream of the frc gene, both of which were lacking in two strains of animal origin, which contained intact frc and oxc genes. An frc(-) insertional mutant of Lact. reuteri 100-23C was compared with the parent strain with respect to oxalate degradation, colonization of an RLF-mouse host model and growth in the presence of acids. Neither parent nor mutant degraded oxalate in vitro or in vivo. However, the parent outcompeted the frc(-) mutant in the mouse intestine during co-colonization and the frc(-) mutant showed a reduced growth rate in the presence of hydrochloric acid. Intact oxc and frc genes do not ensure oxalate degradation under the conditions tested. The frc gene product is important during host colonization and survival of acid stress by Lact. reuteri 100-23C. Oxalate metabolism by oxalate-degrading intestinal bacterial strains may be important in preventing urolithiasis and might lead to the derivation of probiotic products. To produce safe and efficacious probiotics, however, an understanding of the genetic characteristics of potential oxalate degraders must be obtained, together with knowledge of their functional ramifications. © 2014 The Society for Applied Microbiology.

  15. Natural and Accelerated Bioremediation Research (NABIR) Field Research Center (FRC) Management Plan

    Energy Technology Data Exchange (ETDEWEB)

    Watson, D.B.

    2002-02-28

    The Environmental Sciences Division at Oak Ridge National Laboratory has established a Field Research Center (FRC) to support the Natural and Accelerated Bioremediation Research (NABIR) Program on the U.S. Department of Energy (DOE) Oak Ridge Reservation in Oak Ridge, Tennessee for the DOE Headquarters Office of Biological and Environmental Research within the Office of Science.

  16. Results from an 8 Joule RMF-FRC Plasma Translation Experiment for Space Propulsion

    Science.gov (United States)

    Hill, Carrie; Uchizono, Nolan; Holmes, Michael

    2017-10-01

    Field-Reversed Configuration (FRC) thrusters are attractive for advanced in-space propulsion technology as their projected performance, low specific mass, and propellant flexibility offer significant benefits over state-of-the art thrusters. A benchtop experiment to evaluate FRC thruster behavior using a Rotating Magnetic Field (RMF) formation method was constructed at the Air Force Research Laboratory. This experiment generated an RMF-FRC in a conical geometry and accelerated the plasma into a field-free drift region, using 8 J of input energy. Downstream plasma probes in a time-of-flight array measured the exhaust contents of the plasma plume. Results from this diagnostic demonstrated that the ejected mass and ion exit velocities fell short of the desired specific impulse and momentum. Two high-speed cameras were installed to diagnose the gross plasma behavior from two perspectives. Results from these images are presented here. These images show that the plasma generated in the formation region for several different operating conditions was highly non-uniform and did not form a stable closed-field topology that is expected from RMF-FRC plasmas.

  17. Preparasi Minimal pada Pembuatan Gigi Tiruan Cekat dengan Fiber Reinforced Composite (FRC

    Directory of Open Access Journals (Sweden)

    Aditya Ayat Santiko

    2016-11-01

    Full Text Available Dalam praktek sering kali dokter gigi dihadapkan pada pasien yang kehilangan gigi anterior dan ingin segera dibuatkan gigi tiruan karena alasan estetik. Gigi tiruan yang dibuat bisa berupa gigi tiruan sebagian lepasan (GTSL atau gigi tiruan cekat (GTC. Pada GTSL, adanya plat pada palatum menyebabkan rasa tidak nyaman, selain itu pasien setiap kali harus buka pasang gigi tiruan kembali sehingga cukup merepotkan. Oleh karena itu pada umumnya pasien ingin dibuatkan GTC dan hal ini memang sesuai dengan indikasi GTC. Hal yang menjadi pertimbangan pada pembuatan GTC adalah pengasahan permukaan gigi secara keseluruhan bila akan dibuat desain full crown. Pada perkembangan desain GTC ada desain yang disebut resin bonded bridge atau adhesive bridge yaitu GTC yang dibuat pada gigi abutment yang dipreparasi minimal pada bagian palatal saja dan dilekatkan secara mikromekanikal antara retainer sayap logam dan gigi yang telah dipreparasi. Pasien wan ita usia 22 tahun datang ke klinik Prostodonsia RSGM Prof Soedomo UGM karena kehilangan gigi insisif sentral kiri atas. Pada kasus ini dilakukan pembuatan GTC dengan bahan fiber reinforced composite (FRC. Pembuatan bridge dengan bahan FRC dapat dilakukan secara langsung dan tidak langsung. Pada makalah ini akan dibahas pembuatan bridge FRC secara tidak langsung yaitu dengan menggunakan gigi artlfisial komposit. Hasil menunjukkan estetis yang baik, kontrol setelah 2 bulan tidak ada perubahan warna dan pasien merasa puas dengan penampilannya, jaringan gingiva di sekitarnya normal.

  18. Formation of Field Reversed Configuration (FRC on the Yingguang-I device

    Directory of Open Access Journals (Sweden)

    Qizhi Sun

    2017-09-01

    Full Text Available As a hybrid approach to realizing fusion energy, Magnetized Target Fusion (MTF based on the Field Reversed Configuration (FRC, which has the plasma density and confinement time in the range between magnetic and inertial confinement fusion, has been recently widely pursued around the world. To investigate the formation and confinement of the FRC plasma injector for MTF, the Yingguang-I, which is an FRC test device and contains a multi-bank program-discharged pulsed power sub-system, was constructed at the Institute of Fluid Physics (IFP, China. This paper presents the pulsed power components and their parameters of the device in detail, then gives a brief description of progress in experiments of FRC formation. Experimental results of the pulsed power sub-system show that the peak current/magnetic field of 110 kA/0.3 T, 10 kA/1.2 T and 1.7 MA/3.4 T were achieved in the bias, mirror and θ-pinch circuits with quarter cycle of 80 μs, 700 μs and 3.8 μs respectively. The induced electric field in the neutral gas was greater than 0.25 kV/cm when the ionization bank was charged to 70 kV. With H2 gas of 8 Pa, the plasma target of density 1016 cm−3, separatrix radius 4 cm, half-length 17 cm, equilibrium temperature 200 eV and lifetime 3 μs (approximately the half pulse width of the reversed field have been obtained through the θ-pinch method when the bias, mirror, ionization and θ-pinch banks were charged to 5 kV, 5 kV, 55 kV and ±45 kV respectively. The images from the high-speed end-on framing camera demonstrate the formation processes of FRC and some features agree well with the results with the two-dimension magneto hydrodynamics code (2D-MHD.

  19. Research on the fiber reflecting sensor for detecting the residual capacity of the lead-acid battery

    Science.gov (United States)

    Zhao, Mingfu; Zhong, Nianbing; Chen, Yan; Luo, Yuwei

    2006-11-01

    According to the Lambert-Bee law, we can see that the photic absorption coefficient is related to the matter's concentration, the distance of the light through the absorption medium and the transmitted light intensity. The paper just according to the physical phenomena and the theory make the reflex energy relate to the concentration testing of the electrolyte, at the same time the electrolyte's concentration is related to the capacity of lead-acid battery on a corresponding function relation, so we can know the capacity state of the lead-acid battery according to the measurement on the electrolyte's concentration. According to the experiment and research the author deeply discussed how the temperature change affects the capacity of lead-acid battery and the concentration's changing relation, according to the analyses of the thermo-optic effect, we made a new reflecting fiber sensor based on the comparative temperature testing theory and absorption which can eliminate the temperature effect on the tested signal namely the output signal just related to the concentration, so really reflects the change of the capacity of the lead-acid battery when it is in the charge and discharge process. The results of the experiment and theory analyses show that this method is easy to realize the online testing of the capacity of lead-acid battery. This sensor has many merits such as precise measurement, sensitive reaction, long-life use etc. It can be widely used in the electric capacity testing of the automobile lead-acid battery, the electric capacity testing of the industry lead-acid battery, liquor's concentration testing and salinity testing of the sea and have a bright future.

  20. Triceps Brachii in Incomplete Tetraplegia: EMG and Dynamometer Evaluation of Residual Motor Resources and Capacity for Strengthening

    Science.gov (United States)

    2013-01-01

    Background: Candidates for activity-based therapy after spinal cord injury (SCI) are often selected on the basis of manual muscle test scores and the classification of the injury as complete or incomplete. However, these scores may not adequately predict which individuals have sufficient residual motor resources for the therapy to be beneficial. Objective: We performed a preliminary study to see whether dynamometry and quantitative electromyography (EMG) can provide a more detailed assessment of residual motor resources. Methods: We measured elbow extension strength using a hand-held dynamometer and recorded fine-wire EMG from the triceps brachii muscles of 4 individuals with C5, C6, or C7 level SCI and 2 able-bodied controls. We used EMG decomposition to measure motor unit action potential (MUAP) amplitudes and motor unit (MU) recruitment and firing-rate profiles during constant and ramp contractions. Results: All 4 subjects with cervical SCI (cSCI) had increased MUAP amplitudes indicative of denervation. Two of the subjects with cSCI had very weak elbow extension strength (40 pps), suggesting profound loss of motoneurons. The other 2 subjects with cSCI had stronger elbow extension (>6 kg), more normal recruitment, and more normal firing rates, suggesting a substantial remaining motoneuron population. Conclusions: Dynamometry and quantitative EMG may provide information about the extent of gray matter loss in cSCI to help guide rehabilitation strategies. PMID:24244095

  1. 1.4D quasistatic profile model of transport in a field-reversed configuration (FRC)

    International Nuclear Information System (INIS)

    Steinhauer, L.C.

    1990-01-01

    Global confinement models are useful for determining how a given transport mechanism (dependent on local parameters) translates into global confinement times. Such models are also useful for inferring the overall magnitudes of transport rates, and limited information about their spatial profiles. They are especially important in a field reversed configuration (FRC) where the equilibrium and transport rates are so intimately coupled, and where the flux loss time is such an important factor. An earlier global FRC confinement model, sometimes called QUASI, was based on the assumption of a quasi-steady equilibrium. The equilibrium was assumed to have square-ends with some features of 2D equilibria: (1) equal pressure on inner and outer branches of the flux lines; and (2) average-beta relation. Models of this type have been called 1-1/4D transport models. The same general approach has now been applied in a straightforward way to an equilibrium with realistic axial structure. This might be called a 1.4D quasisteady transport model. The assumed axial structure can be that of an analytic equilibrium, or a more complicated computed equilibrium as desired. The example used here is an elongated Hill's vortex equilibrium. As will be shown later, the equilibrium is reflected by two integral quantities that appear in the quasistatic diffusion equation

  2. UEDGE Simulations for Power and Particle Flow Analysis of FRC Rocket

    Science.gov (United States)

    Zheng, Fred; Evans, Eugene S.; McGreivy, Nick; Kaptanoglu, Alan; Izacard, Olivier; Cohen, Samuel A.

    2017-10-01

    The field-reversed configuration (FRC) is under consideration for use in a direct fusion drive (DFD) rocket propulsion system for future space missions. To achieve a rocket configuration, the FRC is embedded within an asymmetric magnetic mirror, in which one end is closed and contains a gas box, and the other end is open and incorporates a magnetic nozzle. Neutral deuterium is injected into the gas box, and flows through the scrape-off layer (SOL) around the core plasma and out the magnetic nozzle, both cooling the core and serving as propellant. Previous studies have examined a range of operating conditions for the SOL of a DFD using UEDGE, a 2D fluid code; discrepancies on the order of 5% were found during the analysis of overall power balance. This work extends the analysis of the previously-studied SOL geometry by updating boundary conditions and conducting a detailed study of power and particle flows within the simulation with the goals of modeling electrical power generation instead of thrust and achieving higher specific impulse. This work was supported, in part, by DOE Contract Number DE-AC02-09CH11466 and Princeton Environmental Institute.

  3. Effect of surface treatment of FRC-Post on bonding strength to resin cements

    Directory of Open Access Journals (Sweden)

    Chan-Hyun Park,

    2011-03-01

    Full Text Available Objectives The purpose of this study was to evaluate the effect of surface treatment of FRC-Post on bonding strength to resin cements. Materials and Methods Pre-surface treated LuxaPost (DMG, Rely-X Fiber Post (3M ESPE and self adhesive resin cement Rely-X Unicem (3M ESPE, conventional resin cement Rely-X ARC (3M ESPE, and Rely-X Ceramic Primer (3M ESPE were used. After completing the surface treatments of the posts, posts and resin cement were placed in clear molds and photo-activation was performed. The specimens were sectioned perpendicular to the FRC-Post into 2 mm-thick segments, and push-out strength were measured. The results of bond strength value were statistically analyzed using independent samples t-test and one-way ANOVA with multiple comparisons using Scheffe's test. Results Silanization of posts affect to the bond strength in LuxaPost, and did not affect in Rely-X Fiber Post. Rely-X ARC showed higher value than Rely-X Unicem. Conclusions Silanization is needed to enhance the bond strength between LuxaPost and resin cements.

  4. Biogeochemistry of Fe and Tc Reduction and Oxidation in FRC Sediment

    International Nuclear Information System (INIS)

    John M, Zachara; James K, Fredrickson; Ravi K, Kukkadapu; Steven C, Smith; David W, Kennedy

    2004-01-01

    The objectives are: (1) To rigorously characterize the distribution of Fe(II) and Fe(III) in FRC sediment. (2) To identify changes to Fe(II)/Fe(III) distribution and concentration resulting from DIRB activity. (3) To determine the dependence of Tc(VII) reduction rate on biogenic Fe(II) and it's forms. (4) To establish tendency of Tc(IV) and biogenic Fe(II) to oxidize and their effects on Tc immobilization. The mineralogic and chemical properties of the pristine, bioreduced, and chemically extracted FRC sediments were characterized by X-ray fluorescence (XRF), X-ray diffraction (XRD), X-ray microscopy (XRM, at the PNC-CAT beamline at APS), Moessbauer spectroscopy, and scanning and transmission electron microscopy with lattice fringe imaging. Chemical extraction included dithionite-citrate-bicarbonate (DCB), acid ammonium oxalate (AAO), and hydroxylamine hydrochloride (HAH). The FRC sediment was incubated under anoxic conditions with the facultative dissimilatory metal-reducing bacterium Shewanella putrefaciens, strain CN32 in defined aqueous solutions/media with bicarbonate and PIPES buffers for time periods exceeding 75 d. Lactate was used as the electron donor. Aqueous and sorbed Fe(II) (ferrozine assay and 0.5 N HCl extraction) and Mn(II) (ICP-MS and 10 mM CuSO 4 extraction), and pH were monitored to define the reduction progress and extent. The bioreduced materials were characterized using the abovementioned techniques. Bioreduced (pasteurized) sediment or chemically extracted/reduced sediment spiked with Fe(II) was washed with a PIPES buffer/electrolyte solution, and spiked with NaTc(VII)O 4 to yield a concentration of 20 (micro)M. The Tc(VII)-spiked samples were agitated and equilibrated at 25 C and sampled over time to assess the Tc(VII) reduction rate. Selected sediment samples containing 20 (micro)M of reduced Tc [Tc(IV)] were subjected to oxidation by: (1) successive headspace replacements of air, and (2) open system equilibration with air. Removed aqueous

  5. The effect of low-NOx combustion on residual carbon in fly ash and its adsorption capacity for air entrainment admixtures in concrete

    DEFF Research Database (Denmark)

    Pedersen, Kim Hougaard; Jensen, Anker Degn; Dam-Johansen, Kim

    2010-01-01

    Fly ash from pulverized coal combustion contains residual carbon that can adsorb the air-entraining admixtures (AEAs) added to control the air entrainment in concrete. This is a problem that has increased by the implementation of low-NOx combustion technologies. In this work, pulverized fuel has...... by up to a factor of 25. This was due to a lower carbon content in the ash and a lower specific AEA adsorptivity of the carbon. The latter was suggested to be caused by changes in the adsorption properties of the unburned char and a decreased formation of soot, which was found to have a large AEA...... adsorption capacity based on measurements on a carbon black. The NOx formation increased by up to three times with more oxidizing conditions and thus, there was a trade-off between the AEA requirements of the ash and NOx formation. The type of fuel had high impact on the AEA adsorption behavior of the ash...

  6. Spontaneous and artificial generation of sheared flow in oblate FRCs in TS-3 and 4 FRC experiments

    International Nuclear Information System (INIS)

    Matsuyama, T.; Kawamori, E.; Ono, Y.; Tsuruda, M.; Sato, K.; Yamanoue, T.; Arimoto, K.; Itagaki, T.; Katsurai, M.

    2003-01-01

    Spontaneous formation of toroidal flow was measured for the first time in oblate FRCs produced in TS-3 and 4 experiments. The toroidal ion flow (V i ∼10km/sec) was found to peak around the magnetic axis, indicating formation of high flow shear inside the separatrix. The toroidal flow was observed to deform the magnetic field lines of the FRC, producing bipolar toroidal field profile. In high-s FRC (averaged number of ion gyro-radius 's'=4.5) with slow flow, its n=1 mode kept growing, causing collapse of the whole configuration. However, in low-s FRC (s=3) with fast flow, the rotating n=2 mode (saturated) became dominant after n=1 mode saturation. The spontaneous formation of flow shear possibly transformed the n=1 mode into the n=2 mode, suggesting a new sheared flow stabilization of n=1 mode. The flow shear was also generated artificially using the 'sling shot' effect of the counter helicity reconnection. The n=1 and 2 mode amplitudes were reduced down to 1/5-1/10 due to the generated flow shear. A new method for continuous sheared-flow generation was proposed for stabilization and heating of FRC by use of intermittent merging of spheromaks with opposing B t . (author)

  7. Absolute calibration of neutron detectors on the C-2U advanced beam-driven FRC

    Energy Technology Data Exchange (ETDEWEB)

    Magee, R. M., E-mail: rmagee@trialphaenergy.com; Clary, R.; Korepanov, S.; Jauregui, F.; Allfrey, I.; Garate, E.; Valentine, T.; Smirnov, A. [Tri Alpha Energy, Inc., Rancho Santa Margarita, California 92688 (United States)

    2016-11-15

    In the C-2U fusion energy experiment, high power neutral beam injection creates a large fast ion population that sustains a field-reversed configuration (FRC) plasma. The diagnosis of the fast ion pressure in these high-performance plasmas is therefore critical, and the measurement of the flux of neutrons from the deuterium-deuterium (D-D) fusion reaction is well suited to the task. Here we describe the absolute, in situ calibration of scintillation neutron detectors via two independent methods: firing deuterium beams into a high density gas target and calibration with a 2 × 10{sup 7} n/s AmBe source. The practical issues of each method are discussed and the resulting calibration factors are shown to be in good agreement. Finally, the calibration factor is applied to C-2U experimental data where the measured neutron rate is found to exceed the classical expectation.

  8. Doppler spectroscopy and D-alpha emission diagnostics for the C-2 FRC plasma

    Energy Technology Data Exchange (ETDEWEB)

    Gupta, Deepak K.; Paganini, E.; Bonelli, L.; Deng, B. H.; Gornostaeva, O.; Hayashi, R.; Knapp, K.; McKenzie, M.; Pousa-Hijos, R.; Primavera, S.; Schroeder, J.; Tuszewski, M. [Tri Alpha Energy, Inc., P.O. Box 7010, Rancho Santa Margarita, California 92688 (United States); Balvis, A.; Giammanco, F.; Marsili, P. [Department of Physics, University of Pisa, Largo B. Pontecorvo 3, 56127 Pisa (Italy)

    2010-10-15

    Two Doppler spectroscopy diagnostics with complementary capabilities are developed to measure the ion temperatures and velocities of FRC plasmas in the C-2 device. First, the multichord ion doppler diagnostic can simultaneously measure 15 chords of the plasma using an image intensified camera. Second, a single-chord fast-response ion Doppler diagnostic provides much higher faster time response by using a 16-channel photo-multiplier tube array. To study the neutral density of deuterium under different wall and plasma conditions, a highly sensitive eight-channel D-alpha diagnostic has been developed and calibrated for absolute radiance measurements. These spectroscopic diagnostics capabilities, combined with other plasma diagnostics, are helping to understand and improve the field reversed configuration plasmas in the C-2 device.

  9. FRC formation studies in a field reversed theta pinch with a variable length coil

    International Nuclear Information System (INIS)

    Maqueda, R.; Sobehart, J.; Rodrigo, A.B.

    1987-01-01

    The formation phase of field reversed configurations (FRC) produced using a theta pinch has received considerable attention lately in connection with the possibility of developing formation methods in time scales longer than the Alven radial time, which would permit the use of low-voltage technology and represent an important engineering simplification in the trend towards larger scale machines sup (1)). The mechanisms leading to the loss of trapped reversed flux during the preheating 2 ) and formation sup (3,4)) stages, looking for maximization of this quantity in order to improve on the stability and transport properties of the configuration in its final equilibrium state are investigated. As a result, semi-emperical scaling laws have been obtained relating the reversed flux loss with experimental operating parameters during the early stages of the formation process 1 ). (author) [pt

  10. Loss estimation of TWDEC for a D-{sup 3}He FRC fusion reactor

    Energy Technology Data Exchange (ETDEWEB)

    Ishikawa, M. [Institute of Engineering Mechanics, Univ. of Tsukuba, Tsukuba, Ibaraki (Japan); Kudo, T.; Yamane, T.; Shimizu, Y.; Tomita, Y.; Momota, H.

    1999-04-01

    Loss mechanisms of TWDEC (Traveling Wave Direct Energy Converter) for a D-{sup 3}He fueled FRC fusion reactor are studied with a numerical analysis. (1) The self-excitation of traveling wave has been attained by the one-dimensional analysis, which shows the conversion efficiency is about 70 to 73%. (2) Axisymmetric two-dimensional analyses have shown that the loss related to the two-dimensional effect without collision with grids is about 5%. (3) The loss related to the collision with grids is the most important, being about 11%. (4) Effects of secondary electrons produced by the collision with grids are rather small and sub-rings can suppress effects of secondary electrons. (5) The loss related to the leaked 3.6 MeV {sup 4}He is about 45 to 60% of the total energy of leaked {sup 4}He. (6) The gross efficiency of TWDEC is estimated over 60%. (author)

  11. Effect of immune system stimulation and divergent selection for residual feed intake on digestive capacity of the small intestine in growing pigs.

    Science.gov (United States)

    Rakhshandeh, A; Dekkers, J C M; Kerr, B J; Weber, T E; English, J; Gabler, N K

    2012-12-01

    Little is known of the consequences of divergent selection for residual feed intake (RFI) on intestinal digestion capacity, particularly during immune system stimulation (ISS). Our objective was to evaluate the impact of ISS and divergent selection for RFI on apparent ileal digestibility (AID) and apparent fecal digestibility (AFD) of nutrients and intestinal nutrient active transport and barrier function. Twenty-eight gilts (63 ± 4 kg BW) from low RFI (LRFI; n = 14) and high RFI (HRFI; n = 14) Yorkshire lines were randomly selected from the Iowa State University RFI herd. Following adaptation, 8 pigs in each line were injected intramuscularly and every 48 h for 7 d with increasing amounts of Escherichia coli lipopolysaccharide (ISS+). Remaining pigs were injected with saline (ISS-). Pigs were then euthanized and ileal digesta was collected for measuring AID of nutrients. Fecal samples were collected on a daily basis and pooled for measuring AFD of nutrients. A segment of ileum was used to measure nutrient transport and transepithelial resistance (TER) and/or barrier integrity by Ussing chambers. No effects of line or its interaction with ISS on AID of CP (N × 6.25) and OM, TER, and active nutrients transport were observed. However, ISS decreased (P digestive capacity of growing pigs during ISS. Immune system stimulation affects both AID and AFD of dietary CP.

  12. Diffusing capacity for lung carbon monoxide (dlco) in chemical lung injuries due to the use of mustard gas in the poisoned soldiers of Iran-Iraq war 2006

    International Nuclear Information System (INIS)

    Rouhi, H.; Ganji, F.

    2010-01-01

    To assess the Mustard gas exposure effects on pulmonary system, particularly on diffusing capacity for lung carbon monoxide (DLCO) and simple spirometry. Sixty-five sulfur mustard- poisoned soldiers from Mostazafan and Janbazan organization were referred to our center in 2005. Complete history, physical examination, chest X ray, Echocardiography, Arterial blood gas, high - resolution computerized tomography, diffusion capacity for lung carbon monoxide and spirometry of these were performed and compared this result with normal value. The mean value of indices in studied injured subjects was: Spirometry: forced expiratory volume in one second (FEV1) = 70.4, Forced vital capacity (FVC) = 66.5, EFE 25-75=81.1, FEV1/FVC=101.9, Flow 25% = 28.7, Flow 50%= 72.9, Flow 75%= 100.1, Sample volume: Functional residual capacity of lungs (FRC) = 131.5, residual volume (RV) = 157.3, RV/TLC= 169.1, Total lung capacity (TLC) = 91.3, KCO= 131.6, TLCO= 116.3. No significant correlation was observed between TLCO values with HRCT, echocardiography, ABG and spirometry values (P>0.05). We recommend TLCO and RV/TLV tests to assess severity of Injuries as there is no a suitable criterion to measure the real consequences of mustard gas on affected combatants. and Biological markers are also needed to determine cause effect relations. (author)

  13. Discrete Calderon’s projections on parallelepipeds and their application to computing exterior magnetic fields for FRC plasmas

    International Nuclear Information System (INIS)

    Kansa, E.; Shumlak, U.; Tsynkov, S.

    2013-01-01

    Confining dense plasma in a field reversed configuration (FRC) is considered a promising approach to fusion. Numerical simulation of this process requires setting artificial boundary conditions (ABCs) for the magnetic field because whereas the plasma itself occupies a bounded region (within the FRC coils), the field extends from this region all the way to infinity. If the plasma is modeled using single fluid magnetohydrodynamics (MHD), then the exterior magnetic field can be considered quasi-static. This field has a scalar potential governed by the Laplace equation. The quasi-static ABC for the magnetic field is obtained using the method of difference potentials, in the form of a discrete Calderon boundary equation with projection on the artificial boundary shaped as a parallelepiped. The Calderon projection itself is computed by convolution with the discrete fundamental solution on the three-dimensional Cartesian grid.

  14. Long pulse FRC sustainment with enhanced edge driven rotating magnetic field current drive

    International Nuclear Information System (INIS)

    Hoffman, A.L.; Guo, H.Y.; Miller, K.E.; Milroy, R.D.

    2005-01-01

    FRCs have been formed and sustained for up to 50 normal flux decay times by Rotating Magnetic Fields (RMF) in the TCS experiment. For these longer pulse times a new phenomenon has been observed: switching to a higher performance mode delineated by shallower RMF penetration, higher ratios of generated poloidal to RMF drive field, and lower overall plasma resistivity. This global data is not explainable by previous RMF theory based on uniform electron rotational velocities or by numerical calculations based on uniform plasma resistivity, but agrees in many respects with new calculations made using strongly varying resistivity profiles. In order to more realistically model RMF driven FRCs with such non-uniform resistivity profiles, a double rigid rotor model has been developed with separate inner and outer electron rotational velocities and resistivities. The results of this modeling suggest that the RMF drive results in very high resistivity in a narrow edge layer, and that the higher performance mode is characterized by a sharp reduction in resistivity over the bulk of the FRC. (author)

  15. FRC formation studies with Z-discharge ionization on FRX-C

    International Nuclear Information System (INIS)

    Armstrong, W.T.; Chrien, R.E.; Hugrass, W.

    1985-01-01

    Recent exploratory operation at high-bias levels on FRX-C is discussed. The motivation of these in situ formation studies was to explore the use of Z-discharge ionization (Z-PI) for achieving larger trapped poloidal flux and commensurately large x/sub s/ values, where x/sub s/ is the ratio of the separatrix radius r/sub s/ to the coil radius r/sub c/. Such studies are of interest in ascertaining predicted improvements of particle confinement and degradation of stability with the associated increase of anti s, the approximate number of ion gyroradii across the minor radius of the FRC. The results of these studies may be summarized briefly as: (1) the Z-PI worked well in conjunction with conventional theta-PI to extend the level of trapped flux at high fill pressure (20 mtorr), but the Z-PI worked poorly at low fill pressure (5 mtorr), and (2) increased trapped flux at 5 mtorr quickly led to degradation of the flux lifetime and no significant increase in x/sub s/, while at 20 mtorr the initial value of x/sub s/ was increased significantly but with degraded flux lifetimes

  16. Measurements of neutral density profiles using a deuterium Balmer-alpha diagnostic in the C-2 FRC plasma

    International Nuclear Information System (INIS)

    Gupta, Deepak K.; Deng, B. H.; Knapp, K.; Sun, X.; Thompson, M. C.

    2012-01-01

    In C-2 field-reversed configuration (FRC) device, low neutral density outside the FRC separatrix is required to minimize the charge exchange loss of fast particles. Titanium gettering is used in C-2 to reduce the wall recycling and keep the neutral density low in plasma edge. The measurements of neutral density radial profile are desirable to understand the plasma recycling and the effects of titanium gettering. These measurements are also needed to study the interaction of neutral beams with FRC plasma and confinement of fast ions. Diagnostic based on absolute deuterium Balmer-alpha (D-alpha) radiation measurements is developed and deployed on C-2 device to measure the radial profile of neutral density. Simultaneous measurements of electron density and temperature are done using CO 2 interferometer, Thomson scattering, and triple probes diagnostics along with absolute D-alpha radiation. Abel inversion was performed to get the time dependent radial profile of the local D-alpha emission density. Neutral density profiles are obtained under different machine conditions of titanium deposition.

  17. Effect of length and diameter of fiber reinforced composite post (FRC on fracture resistance of remaining tooth structure

    Directory of Open Access Journals (Sweden)

    Mahdiyeh seifi

    2013-03-01

    Full Text Available Introduction: Post and core has been considered for endodontically treated tooth, especially in cases with severe damage crowns. Recently fiber reinforced composite posts (FRC post have been used in the treatment of endodontically treated teeth. Because the length and diameter of posts are effective in stress distribution, the purpose of this study is to evaluate the effect of length and diameter of FRC post on fracture resistance. Methods: In this experimental study, 36 glass fiber posts with combination of 7mm, 9mm, and 12mm length and 1.1mm, 1.3mm and 1.5mm diameter were divided into 9 groups of 4. These posts were cemented in root canals by Panavia. Samples were tested with 45° compressive forces for the evaluation of fracture resistance. Datas were analyzed using SPSS soft ware and One- way and Two-way ANOVA analyses. Results: Fracture resistance did not increase significantly with the effect of length and diameter simultaneously (P=0.85. Samples with 12mm length and 1.5mm diameter had the greatest fracture resistance (1023/33N±239/22. The minimum fracture resistance had occurred in post with 7mm length and 1.5mm diameter (503/13N ±69/18. Fracture resistance increased significantly by increasing the length and the same diameter. Conclusion: It can be concluded that fracture resistance is affected by the length and not the diameter of FRC post.

  18. FRC [field-reversed configuration] translation studies on FRX-C/LSM

    International Nuclear Information System (INIS)

    Rej, D.; Barnes, G.; Baron, M.

    1989-01-01

    In preparation for upcoming compression-heating experiments, field-reversed configurations (FRCs) have been translated out of the FRX-C/LSM θ-pinch source, and into the 0.4-m-id, 6.7-m-long translation region formerly used on FRX-C/T. Unlike earlier experiments FRCs are generated without magnetic tearing in the larger FRX-C/LSM source (nominal coil id = 0.70 m, length = 2 m); larger, lower-energy-density FRCs are formed: r/sub s/ ≅ 0.17 m, B/sub ext/ ≅ 0.35 T, ≅ 7 /times/ 10 20 m/sup /minus/3/ and T/sub e/ + T/sub i/ ≅ 400 eV. An initial 3-mtorr D 2 pressure is introduced by either static or puff fill. Asymmetric fields from auxiliary end coils (used for non-tearing formation) provide the accelerating force on the FRC, thereby eliminating the need for a conical θ-pinch coil. An important feature is the abrupt 44% decrease in the flux-conserving wall radius at the transition between the θ-pinch and translation region, similar to that in the compressor. In this paper we review a variety of issues addressed by the recent translation experiments: translation dynamics; translation through a modulated magnetic field; stabilization of the n = 2 rotational instability by weak helical quadrupole fields; and confinement properties. Results from internal magnetic field measurements in translating FRCs may be found in a companion paper. 10 refs., 5 figs

  19. High Flux FRC Facility for the Stability, Confinement and ITER Divertor Studies

    Energy Technology Data Exchange (ETDEWEB)

    Hoffman, Alan L. [Univ. of Washington, Seattle, WA (United States). Aerospace and Energetics Research Program. Redmond Plasma Physics Lab.; Milroy, Richard D. [Univ. of Washington, Seattle, WA (United States). Aerospace and Energetics Research Program. Redmond Plasma Physics Lab.

    2014-01-31

    The TCS (Translation, Confinement, & Sustainment) program was begun on 7 August, 1996 to renew basic studies of the Field Reversed Configuration (FRC). The program made use of the old LSX (Large s Experiment) device, which was constructed at STI during the period from 1986 to 1990, but only operated for one year due to a DOE decision at the time to focus exclusively on the tokamak configuration. LSX was transferred to the University of Washington in 1992 and modified (LSX/mod) to perform Tokamak Refueling by Accelerated Plasmoids (TRAP) experiments. The TRAP program was funded from 7 August, 1992 until 6 August, 1996, but was utilized for an additional year while TCS was being constructed. During the first TCS funding period TCS was completed and initial experiments were begun. A large multi-megawatt RF power supply was built by Los Alamos National Laboratory (LANL) for use with a Rotating Magnetic Field (RMF) system, and LANL has been a continuing participant in our experimental program. A smaller prototype facility, called the Star Thrust Experiment (STX) was also built and operated in this period, partly with NASA funding, before TCS came on-line. A final report for this construction period was submitted in September 2000. A first renewal period (2.5 years) provided operating funds for the period between July 7, 2000 and January 6, 2003. A great deal of progress was made in understanding the use of RMF to both form and sustain FRCs during this period. The principal result of the experimental program was the formation of quasi steady-state (as long as RMF power was available) FRCs with densities in the 1-3x1019 m-3 range. However, the plasma temperature (Te or Ti) was limited to sub-25 eV, except transiently during start-up, by the rapid accumulation of impurities. This is not surprising since TCS was only designed to demonstrate RMF flux build-up and was not provided with either fueling capabilities or modern vacuum

  20. Identification of Amino Acid Residues Responsible for the Enantioselectivity and Amide Formation Capacity of the Arylacetonitrilase from Pseudomonas fluorescens EBC191 ▿ †

    Science.gov (United States)

    Kiziak, Christoph; Stolz, Andreas

    2009-01-01

    The nitrilase from Pseudomonas fluorescens EBC191 converted (R,S)-mandelonitrile with a low enantioselectivity to (R)-mandelic acid and (S)-mandeloamide in a ratio of about 4:1. In contrast, the same substrate was hydrolyzed by the homologous nitrilase from Alcaligenes faecalis ATCC 8750 almost exclusively to (R)-mandelic acid. A chimeric enzyme between both nitrilases was constructed, which represented in total 16 amino acid exchanges in the central part of the nitrilase from P. fluorescens EBC191. The chimeric enzyme clearly resembled the nitrilase from A. faecalis ATCC 8750 in its turnover characteristics for (R,S)-mandelonitrile and (R,S)-2-phenylpropionitrile (2-PPN) and demonstrated an even higher enantioselectivity for the formation of (R)-mandelic acid than the nitrilase from A. faecalis. An alanine residue (Ala165) in direct proximity to the catalytically active cysteine residue was replaced in the nitrilase from P. fluorescens by a tryptophan residue (as found in the nitrilase from A. faecalis ATCC 8750 and most other bacterial nitrilases) and several other amino acid residues. Those enzyme variants that possessed a larger substituent in position 165 (tryptophan, phenylalanine, tyrosine, or histidine) converted racemic mandelonitrile and 2-PPN to increased amounts of the R enantiomers of the corresponding acids. The enzyme variant Ala165His showed a significantly increased relative activity for mandelonitrile (compared to 2-PPN), and the opposite was found for the enzyme variants carrying aromatic residues in the relevant position. The mutant forms carrying an aromatic substituent in position 165 generally formed significantly reduced amounts of mandeloamide from mandelonitrile. The important effect of the corresponding amino acid residue on the reaction specificity and enantiospecificity of arylacetonitrilases was confirmed by the construction of a Trp164Ala variant of the nitrilase from A. faecalis ATCC 8750. This point mutation converted the highly R

  1. Loss mechanisms of travelling wave direct energy converters for D-{sup 3}He FRC fusion reactors

    Energy Technology Data Exchange (ETDEWEB)

    Ishikawa, M. E-mail: misikawa@kz.tsukuba.ac.jp; Yamane, T.; Shimizu, Y.; Momota, H.; Tomita, Y.; Miley, G.H

    2000-11-01

    Loss mechanisms of TWDEC for a D-{sup 3}He fuelled FRC fusion reactor are studied with numerical analysis. (1) The self-excitation of a travelling wave has been attained with external electric circuits, which shows the conversion efficiency is about 70-73%. (2) Three-dimensional behavior has been studied by axisymmetric approximation, showing that the loss related to the radial non-uniformity effect without collision with grids is about 5%. (3) The loss related to the collision with grids is the most important, being about 11%. (4) Effects of secondary electrons produced by the collision with the grids are rather small and subrings can suppress the effects of secondary electrons. (5) The loss related to leaked 3.6 MeV {alpha} particles is about 45-60% of the total energy of leaked {alpha} particles. (6) The gross efficiency of TWDEC is estimated to be over 60%.

  2. Residual deposits (residual soil)

    International Nuclear Information System (INIS)

    Khasanov, A.Kh.

    1988-01-01

    Residual soil deposits is accumulation of new formate ore minerals on the earth surface, arise as a result of chemical decomposition of rocks. As is well known, at the hyper genes zone under the influence of different factors (water, carbonic acid, organic acids, oxygen, microorganism activity) passes chemical weathering of rocks. Residual soil deposits forming depends from complex of geologic and climatic factors and also from composition and physical and chemical properties of initial rocks

  3. Influence of Different Techniques of Laboratory Construction on the Fracture Resistance of Fiber-Reinforced Composite (FRC) Bridges.

    Science.gov (United States)

    Ellakwa, Ayman E; Shortall, Adrian C; Marquis, Peter M

    2004-11-15

    The aim of the current investigation is to evaluate optimal pontic and retainer fiber positions for Polyethylene fiber-reinforced composite (FRC) restorations. In series I notch disc specimens were used to mimic loading cuspal regions of pontics. Four groups (n=15/group; codes A to D) were prepared from Artglass composite. Groups A to C were reinforced with polyethylene fibers, and group D was an unreinforced control. Fibers were positioned either around (A), beneath the notch (B), or at the disc base (C). Specimens were stored in distilled water at 37 degrees C for 24 h before testing to failure (CHS=1mm/min) in a universal testing machine. Mean torque to failure values ranked [P C = D. In series II five groups of three unit bridges (n =5/group; codes A to E) were prepared from Artglass dental composite without (group A) or with (groups B to E) different Connect fiber reinforcement locations/techniques. Bridges were cemented using 2 bond resin cement to a standardized substructure. After storage, as per series I, bridges were loaded mid-pontic region to failure. One-way ANOVA showed no significant (P=0.08) difference between test groups. The research hypothesis was that notched disc and 3 unit bridge test techniques would discriminate equally between fiber-reinforced specimens and an unreinforced composite control was rejected.

  4. A single-residue change in the HIV-1 V3 loop associated with maraviroc resistance impairs CCR5 binding affinity while increasing replicative capacity.

    Science.gov (United States)

    Garcia-Perez, Javier; Staropoli, Isabelle; Azoulay, Stéphane; Heinrich, Jean-Thomas; Cascajero, Almudena; Colin, Philippe; Lortat-Jacob, Hugues; Arenzana-Seisdedos, Fernando; Alcami, Jose; Kellenberger, Esther; Lagane, Bernard

    2015-06-18

    Maraviroc (MVC) is an allosteric CCR5 inhibitor used against HIV-1 infection. While MVC-resistant viruses have been identified in patients, it still remains incompletely known how they adjust their CD4 and CCR5 binding properties to resist MVC inhibition while preserving their replicative capacity. It is thought that they maintain high efficiency of receptor binding. To date however, information about the binding affinities to receptors for inhibitor-resistant HIV-1 remains limited. Here, we show by means of viral envelope (gp120) binding experiments and virus-cell fusion kinetics that a MVC-resistant virus (MVC-Res) that had emerged as a dominant viral quasispecies in a patient displays reduced affinities for CD4 and CCR5 either free or bound to MVC, as compared to its MVC-sensitive counterpart isolated before MVC therapy. An alanine insertion within the GPG motif (G310_P311insA) of the MVC-resistant gp120 V3 loop is responsible for the decreased CCR5 binding affinity, while impaired binding to CD4 is due to sequence changes outside V3. Molecular dynamics simulations of gp120 binding to CCR5 further emphasize that the Ala insertion alters the structure of the V3 tip and weakens interaction with CCR5 ECL2. Paradoxically, infection experiments on cells expressing high levels of CCR5 also showed that Ala allows MVC-Res to use CCR5 efficiently, thereby improving viral fusion and replication efficiencies. Actually, although we found that the V3 loop of MVC-Res is required for high levels of MVC resistance, other regions outside V3 are sufficient to confer a moderate level of resistance. These sequence changes outside V3, however, come with a replication cost, which is compensated for by the Ala insertion in V3. These results indicate that changes in the V3 loop of MVC-resistant viruses can augment the efficiency of CCR5-dependent steps of viral entry other than gp120 binding, thereby compensating for their decreased affinity for entry receptors and improving their

  5. Railway capacity

    OpenAIRE

    Lavrič, Tadeja

    2012-01-01

    In the first part of the thesis, the concepts of railway capacity and capacity consumption are defined. Experts have in the past defined railway capacity in many different ways. This thesis outlines some definitions of railway capacity and capacity consumption, including the definition of railway capacity in accordance with the UIC code 406 (2004), given by the International Union of Railways in order to standardize the definition of railway capacity. Capacity and capacity consumption are dir...

  6. Retention capacity of samarium (III) in zircon for it possible use in retaining walls for confinement of nuclear residues; Capacidad de retencion de samario (III) en circon para su posible uso en barreras de contencion para confinamiento de residuos nucleares

    Energy Technology Data Exchange (ETDEWEB)

    Garcia G, N

    2006-07-01

    Mexico, as country that produces part of its electric power by nuclear means, should put special emphasis in the development of technologies guided to the sure and long term confinement of the high level nuclear residuals. This work studies the capacity that has the natural zircon to retain to the samarium (III) in solution, by what due, firstly, to characterize the zircon for technical instrumental to determine the purity and characteristic of the mineral in study. The instrumental techniques that were used to carry out the physicochemical characterization were the neutron activation analysis (NAA), the infrared spectroscopy (IS), the thermal gravimetric analysis (TGA), scanning electron microscopy (SEM), transmission electron microscopy (TEM), semiquantitative analysis, dispersive energy spectroscopy (EDS), X-ray diffraction (XRD) and luminescence technique. The characterization of the surface properties carries out by means of the determination of the surface area using the BET multipoint technique, acidity constants, hydration time, the determination of the point of null charge (pH{sub PCN}) and density of surface sites (D{sub s}). The luminescence techniques were useful to determine the optimal point hydration of the zircon and for the quantification of the samarium, for that here intends the development of both analysis techniques. With the adjustment of the titration curves in the FITEQL 4 package the constants of surface acidity in the solid/liquid interface were determined. To the finish of this study it was corroborated that the zircon is a mineral that presents appropriate characteristics to be proposed as a contention barrier for the deep geologic confinement. With regard to the study of adsorption that one carries out the samarium retention it is superior to 90% under the described conditions. This investigation could also be applicable in the confinement of dangerous industrial residuals. (Author)

  7. Residual load carrying capacity of timber joints

    NARCIS (Netherlands)

    Kuilen, J.W.G. van de

    1999-01-01

    Timber joints that have been preloaded for 2 to 8 years have been short term tested in accordance with EN 26891. The applied load levels varied between 30% and 50% of the average short term strength. The study comprised nailed, toothed-plate and split-ring joints. All joints were made of spruce and

  8. Tryptophan scanning mutagenesis of aromatic residues within the polymerase domain of HIV-1 reverse transcriptase: critical role of Phe-130 for p51 function and second-site revertant restoring viral replication capacity.

    Science.gov (United States)

    Olivares, Isabel; Gutiérrez-Rivas, Mónica; López-Galíndez, Cecilio; Menéndez-Arias, Luis

    2004-07-01

    The effects on virus viability and reverse transcriptase (RT) function of substituting Trp for Tyr or Phe residues within the polymerase domain of human immunodeficiency virus type 1 (HIV-1) RT have been analyzed with an infectious HIV-1 clone. Viruses containing mutations Y56W, F61W, F87W, F116W, Y127W, Y144W, F171W, Y181W, Y183W, Y188W, F227W, or Y232W in their RT-coding regions were viable and showed replication capacities similar or slightly reduced in comparison with the wild-type HIV-1. However, RTs bearing mutations F77W or Y146W had a dNTP-binding defect, rendering nonviable viruses. HIV-1 carrying RT mutations F124W or F130W replicated very poorly, but compensatory changes (K83R for F124W, and T58S for F130W) were selected upon passaging the virus in cell culture. The amino acid substitution F130W diminishes the stability of the 51-kDa subunit of the RT (p51) and impairs polyprotein processing in virus-infected cells, an effect that can be mitigated when T58S is found in p51.

  9. Residuation theory

    CERN Document Server

    Blyth, T S; Sneddon, I N; Stark, M

    1972-01-01

    Residuation Theory aims to contribute to literature in the field of ordered algebraic structures, especially on the subject of residual mappings. The book is divided into three chapters. Chapter 1 focuses on ordered sets; directed sets; semilattices; lattices; and complete lattices. Chapter 2 tackles Baer rings; Baer semigroups; Foulis semigroups; residual mappings; the notion of involution; and Boolean algebras. Chapter 3 covers residuated groupoids and semigroups; group homomorphic and isotone homomorphic Boolean images of ordered semigroups; Dubreil-Jacotin and Brouwer semigroups; and loli

  10. Residue processing

    Energy Technology Data Exchange (ETDEWEB)

    Gieg, W.; Rank, V.

    1942-10-15

    In the first stage of coal hydrogenation, the liquid phase, light and heavy oils were produced; the latter containing the nonliquefied parts of the coal, the coal ash, and the catalyst substances. It was the problem of residue processing to extract from these so-called let-down oils that which could be used as pasting oils for the coal. The object was to obtain a maximum oil extraction and a complete removal of the solids, because of the latter were returned to the process they would needlessly burden the reaction space. Separation of solids in residue processing could be accomplished by filtration, centrifugation, extraction, distillation, or low-temperature carbonization (L.T.C.). Filtration or centrifugation was most suitable since a maximum oil yield could be expected from it, since only a small portion of the let-down oil contained in the filtration or centrifugation residue had to be thermally treated. The most satisfactory centrifuge at this time was the Laval, which delivered liquid centrifuge residue and centrifuge oil continuously. By comparison, the semi-continuous centrifuges delivered plastic residues which were difficult to handle. Various apparatus such as the spiral screw kiln and the ball kiln were used for low-temperature carbonization of centrifuge residues. Both were based on the idea of carbonization in thin layers. Efforts were also being made to produce electrode carbon and briquette binder as by-products of the liquid coal phase.

  11. Residual risk

    African Journals Online (AJOL)

    ing the residual risk of transmission of HIV by blood transfusion. An epidemiological approach assumed that all HIV infections detected serologically in first-time donors were pre-existing or prevalent infections, and that all infections detected in repeat blood donors were new or incident infections. During 1986 - 1987,0,012%.

  12. Weather and road capacity

    DEFF Research Database (Denmark)

    Jensen, Thomas Christian

    2014-01-01

    The paper presents estimations of the effect of bad weather on the observed speed on a Danish highway section; Køge Bugt Motorvejen. The paper concludes that weather, primarily precipitation and snow, has a clear negative effect on speed when the road is not in hypercongestion mode. Furthermore......, the capacity of the highway seems to be reduced in bad weather and there are indications that travel time variability is also increased, at least in free-flow conditions. Heavy precipitation reduces speed and capacity by around 5-8%, whereas snow primarily reduces capacity. Other weather variables......-parametrically against traffic density and in step 2 the residuals from step 1 are regressed linearly against the weather variables. The choice of a non-parametric method is made to avoid constricting ties from a parametric specification and because the focus here is not on the relationship between traffic flow...

  13. Residual basins

    International Nuclear Information System (INIS)

    D'Elboux, C.V.; Paiva, I.B.

    1980-01-01

    Exploration for uranium carried out over a major portion of the Rio Grande do Sul Shield has revealed a number of small residual basins developed along glacially eroded channels of pre-Permian age. Mineralization of uranium occurs in two distinct sedimentary units. The lower unit consists of rhythmites overlain by a sequence of black shales, siltstones and coal seams, while the upper one is dominated by sandstones of probable fluvial origin. (Author) [pt

  14. Load-bearing capacity of indirect inlay-retained fixed dental prostheses made of particulate filler composite alone or reinforced with E-glass fibers impregnated with various monomers.

    Science.gov (United States)

    Özcan, Mutlu; Koekoek, Winand; Pekkan, Gurel

    2012-08-01

    The load-bearing capacity and failure types of indirect inlay-retained fixed dental prostheses (FDP), made of particulate filler composite (PFC) (Estenia) alone or reinforced with E-glass fibers impregnated with various monomers were evaluated. Indirect inlay-retained FDPs were made between first premolars and first molars (N=30, 10/per group). The inlay parts of the specimens were silica coated and silanized and the specimens were cemented with dual-polymerized resin cement under ultrasonic vibrations. The experimental groups were as follows: Group 1: FRC1 (BR-100, UTMA) + PFC; Group 2: FRC2 (everStick C&B, Bis-GMA/PMMA) + PFC; Group 3: PFC only. The specimens were kept in distilled water at 37 °C for one month and then subjected to fracture strength test. No significant difference was found between the Group 1 and Group 2 FDPs (1357±301 N and 1213±316 N, respectively) (p>0.05) (ANOVA). Group 3 (856±299 N) showed significantly lower results than those of FRC reinforced groups (pinlay cavities. FDPs made of PFC only showed mainly catastrophic fracture of the pontic. In the FRC reinforced groups, predominantly delamination of the veneering was observed. The use of silica coating and silanization in combination with the dual-polymerized resin cement used; under ultrasonic cementation procedure provided sufficient adhesion to withstand static loading forces at the cementation interface, since the failures were predominantly delamination of the veneering in the FRC reinforced groups. Copyright © 2012 Elsevier Ltd. All rights reserved.

  15. RESIDUAL RISK ASSESSMENTS - RESIDUAL RISK ...

    Science.gov (United States)

    This source category previously subjected to a technology-based standard will be examined to determine if health or ecological risks are significant enough to warrant further regulation for Coke Ovens. These assesments utilize existing models and data bases to examine the multi-media and multi-pollutant impacts of air toxics emissions on human health and the environment. Details on the assessment process and methodologies can be found in EPA's Residual Risk Report to Congress issued in March of 1999 (see web site). To assess the health risks imposed by air toxics emissions from Coke Ovens to determine if control technology standards previously established are adequately protecting public health.

  16. Evaluation of Ultimate Pressure Capacity of a Prestressed Concrete Containment Building with Steel or Polyamide Fiber Reinforcement

    Energy Technology Data Exchange (ETDEWEB)

    Choun, Youngsun; Hahm, Daegi [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2014-05-15

    Fiber reinforced concrete (FRC) includes thousands of small fibers that are distributed randomly in the concrete. Fibers resist the growth of cracks in concrete through their bridging at the cracks. Therefore, FRC fails in tension only when the fibers break or are pulled out of the cement matrix. For this reason, the addition of fibers in concrete mixing increases the tensile toughness of concrete and enhances the post-cracking behavior. A prevention of through-wall cracks and an increase of the post-cracking ductility will improve the ultimate internal pressure capacity of a prestressed concrete containment building (PCCB). In this study, the effects of steel or polyamide fiber reinforcement on the ultimate pressure capacity of a PCCB are evaluated. When R-SFRC contains hooked steel fibers in a volume fraction of 1.0%, the ultimate pressure capacity of a PCCB can be improved by 17%. When R-PFRC contains polyamide fibers in a volume fraction of 1.5%, the ultimate pressure capacity of a PCCB can be enhanced by 10%. Further studies are needed to determine the strain limits acceptable for PCCBs reinforced with fibers.

  17. Residual nilpotence and residual solubility of groups

    International Nuclear Information System (INIS)

    Mikhailov, R V

    2005-01-01

    The properties of the residual nilpotence and the residual solubility of groups are studied. The main objects under investigation are the class of residually nilpotent groups such that each central extension of these groups is also residually nilpotent and the class of residually soluble groups such that each Abelian extension of these groups is residually soluble. Various examples of groups not belonging to these classes are constructed by homological methods and methods of the theory of modules over group rings. Several applications of the theory under consideration are presented and problems concerning the residual nilpotence of one-relator groups are considered.

  18. Carrying Capacity

    DEFF Research Database (Denmark)

    Schroll, Henning; Andersen, Jan; Kjærgård, Bente

    2012-01-01

    A spatial planning act was introduced inIndonesia 1992 and renewed in 2008. It emphasised the planning role of decentralised authorities. The spatial planning act covers both spatial and environmental issues. It defines the concept of carrying capacity and includes definitions of supportive....../cities. Four different sectors (water, food production, waste, and forests) were selected as core areas for decentralised spatial planning. Indicators for SCC and ACC were identified and assessed with regard to relevance and quantifiability. For each of the indicators selected, a legal threshold or guiding...... was introduced inIndonesia 1992 and renewed in 2008. It emphasised the planning role of decentralised authorities. The spatial planning act covers both spatial and environmental issues. It defines the concept of carrying capacity and includes definitions of supportive carrying capacity (SCC) and assimilative...

  19. Station Capacity

    DEFF Research Database (Denmark)

    Landex, Alex

    2011-01-01

    the probability of conflicts and the minimum headway times into account. The last method analyzes how optimal platform tracks are used by examining the arrival and departure pattern of the trains. The developed methods can either be used separately to analyze specific characteristics of the capacity of a station...

  20. Biodegradation of some agricultural residues by fungi in agitated ...

    African Journals Online (AJOL)

    Digestibility of agricultural residues in animal feeding is deeply dependent on the amounts and types of their fibers. Biological treatment of agricultural residues is a new method for improvement of digestibility. Therefore, the capacity of a few fungi in biodegradation of some agricultural residues was studied. Losses of crude ...

  1. Trends and advances in pesticide residue analysis | Yeboah ...

    African Journals Online (AJOL)

    The nature, origin and the economic significance of pesticide residues are reviewed to underscore the need for countries to develop the ability and capacity to monitor pesticide residues. An overview of pesticide residues analytical procedures is also presented with emphasis on thin layer chromatography (TLC) as an ...

  2. Exerting Capacity.

    Science.gov (United States)

    Leger, J Michael; Phillips, Carolyn A

    2017-05-01

    Patient safety has been at the forefront of nursing research since the release of the Institute of Medicine's report estimating the number of preventable adverse events in hospital settings; yet no research to date has incorporated the perspectives of bedside nurses using classical grounded theory (CGT) methodology. This CGT study explored the perceptions of bedside registered nurses regarding patient safety in adult acute care hospitals. Data analysis used three techniques unique to CGT-the constant comparative method, coding, and memoing-to explore the values, realities, and beliefs of bedside nurses about patient safety. The analysis resulted in a substantive theory, Exerting Capacity, which explained how bedside nurses balance the demands of keeping their patients safe. Exerting Capacity has implications for health care organization leaders, nursing leaders, and bedside nurses; it also has indications for future research into the concept of patient safety.

  3. Bioenergy from sisal residues

    Energy Technology Data Exchange (ETDEWEB)

    Jungersen, G. [Dansk Teknologisk Inst. (Denmark); Kivaisi, A.; Rubindamayugi, M. [Univ. of Dar es Salaam (Tanzania, United Republic of)

    1998-05-01

    The main objectives of this report are: To analyse the bioenergy potential of the Tanzanian agro-industries, with special emphasis on the Sisal industry, the largest producer of agro-industrial residues in Tanzania; and to upgrade the human capacity and research potential of the Applied Microbiology Unit at the University of Dar es Salaam, in order to ensure a scientific and technological support for future operation and implementation of biogas facilities and anaerobic water treatment systems. The experimental work on sisal residues contains the following issues: Optimal reactor set-up and performance; Pre-treatment methods for treatment of fibre fraction in order to increase the methane yield; Evaluation of the requirement for nutrient addition; Evaluation of the potential for bioethanol production from sisal bulbs. The processing of sisal leaves into dry fibres (decortication) has traditionally been done by the wet processing method, which consumes considerable quantities of water and produces large quantities of waste water. The Tanzania Sisal Authority (TSA) is now developing a dry decortication method, which consumes less water and produces a waste product with 12-15% TS, which is feasible for treatment in CSTR systems (Continously Stirred Tank Reactors). (EG)

  4. Capacity Building

    International Nuclear Information System (INIS)

    Molloy, Brian; Mallick, Shahid

    2014-01-01

    Outcomes & Recommendations: • Significant increase needed in the nuclear workforce both to replace soon-to-retire current generation and to staff large numbers of new units planned • Key message, was the importance of an integrated approach to workforce development. • IAEA and other International Organisations were asked to continue to work on Knowledge Management, Networks and E&T activities • IAEA requested to conduct Global Survey of HR needs – survey initiated but only 50% of operating countries (30% of capacity) took part, so results inconclusive

  5. Increased of the capacity integral bridge with reinforced concrete beams for single span

    Science.gov (United States)

    Setiati, N. Retno

    2017-11-01

    Sinapeul Bridge that was built in 2012 in Sumedang is a bridge type using a full integral system. The prototype of integral bridge with reinforced concrete girder and single span 20 meters until this year had decreased capacity. The bridge was conducted monitoring of strain that occurs in the abutment in 2014. Monitoring results show that based on the data recorded, the maximum strain occurs at the abutment on the location of the integration of the girder of 10.59 x 10-6 tensile stress of 0.25 MPa (smaller than 150 x 10-6) with 3 MPa tensile stress as limit the occurrence of cracks in concrete. Sinapeul bridge abutment with integral system is still in the intact condition. Deflection of the bridge at the time of load test is 1.31 mm. But this time the bridge has decreased exceeded permission deflection (deflection occurred by 40 mm). Besides that, the slab also suffered destruction. One cause of the destruction of the bridge slab is the load factor. It is necessary for required effort to increase the capacity of the integral bridge with retrofitting. Retrofitting method also aims to restore the capacity of the bridge structure due to deterioration. Retrofitting can be done by shortening of the span or using Fibre Reinforced Polymer (FRC). Based on the results obtained by analysis of that method of retrofitting with Fibre Reinforced Polymer (FRC) is more simple and effective. Retrofitting with FRP can increase the capacity of the shear and bending moment becomes 41% of the existing bridge. Retrofitting with FRP method does not change the integral system on the bridge Sinapeul become conventional bridges.

  6. Capacity and Capacity Utilization in Fishing Industries

    OpenAIRE

    Kirkley, James E; Squires, Dale

    1999-01-01

    Excess capacity of fishing fleets is one of the most pressing problems facing the world's fisheries and the sustainable harvesting of resource stocks. Considerable confusion persists over the definition and measurement of capacity and capacity utilization in fishing. Fishing capacity and capacity utilization, rather than capital (or effort) utilization, provide the appropriate framework. This paper provides both technological-economic and economic definitions of capacity and excess capacity i...

  7. Seismic fragility capacity of equipment

    International Nuclear Information System (INIS)

    Iijima, Toru; Abe, Hiroshi; Suzuki, Kenichi

    2006-01-01

    Seismic probabilistic safety assessment (PSA) is an available method to evaluate residual risks of nuclear plants that are designed on definitive seismic conditions. From our preliminary seismic PSA analysis, horizontal shaft pumps are important components that have significant influences on the core damage frequency (CDF). An actual horizontal shaft pump and some kinds of elements were tested to evaluate realistic fragility capacities. Our test results showed that the realistic fragility capacity of horizontal shaft pump would be at least four times as high as a current value, 1.6 x 9.8 m/s 2 , used for our seismic PSA. We are going to incorporate the fragility capacity data that were obtained from those tests into our seismic PSA analysis, and we expect that the reliability of seismic PSA should increase. (author)

  8. The residual load carrying capacity of timber joints

    NARCIS (Netherlands)

    Van de Kuilen, J.W.G.

    1999-01-01

    Timber joints that have been preloaded for 2 to 8 years have been short term tested in accordance with EN 26891. The applied load levels varied between 30% and 50% of the average short term strength. The study comprised nailed, toothed-plate and split-ring joints. All joints were made of spruce and

  9. Residual capacity of a damaged water mist system

    NARCIS (Netherlands)

    Wal, R. van der; Rahm, M.; Hiltz, J.; Claesson, A.; Boonacker, B.

    2013-01-01

    Navies have been facing budget reductions over the past decade. Since crew size is a major cost driver, this has led to efforts to reduce manning on board naval ships. Traditionally, damage control and firefighting were manpower intensive operations. To enable crewing level reductions without

  10. Caracterização Estrutural e da Capacidade de Absorção de Água em Bloco de Cimento com Adição de Resíduo de Pneu (Ecobloco = Water Absorption Capacity and Structural Characterization of Cement Block with Addition of Tire Residue (Ecobloco.

    Directory of Open Access Journals (Sweden)

    Maria da Conceição S. Gomes

    2007-12-01

    Full Text Available Foram feitos caracterizações estruturais com ensaios em corpo de prova, medidas granulométricas do resíduo, docimento, do pó de brita e da areia, e a medida da capacidade de absorção de água em blocos de cimento (chamados de ecoblocos com adição de 5%, 10%, 15%, 25% e 35% de resíduo de pneu, obtido por meio de raspagem de pneus automotivos inservíveis. A geometria de confecção dos ecoblocos foi projetada para serem encaixados no empilhamento vertical, requerendo o mínimo de massa de cimento para a confecção de parede de vedação. = Experiment for structural characterizations were made in test body as well as measurements of the capacity of water absorption in cement blocks (called ecoblocos with the addition of 5%, 10%, 15%, 25% and 35% of tire residue.These additions are obtained by means of worn out tire’s scratching. The ecoblocos´ design was projected for them to be inserted in the vertical piling up, requesting the minimum of mortar for the construction of walls.

  11. Residual gas analysis

    International Nuclear Information System (INIS)

    Berecz, I.

    1982-01-01

    Determination of the residual gas composition in vacuum systems by a special mass spectrometric method was presented. The quadrupole mass spectrometer (QMS) and its application in thin film technology was discussed. Results, partial pressure versus time curves as well as the line spectra of the residual gases in case of the vaporization of a Ti-Pd-Au alloy were demonstrated together with the possible construction schemes of QMS residual gas analysers. (Sz.J.)

  12. Agricultural pesticide residues

    International Nuclear Information System (INIS)

    Fuehr, F.

    1984-01-01

    The utilization of tracer techniques in the study of agricultural pesticide residues is reviewed under the following headings: lysimeter experiments, micro-ecosystems, translocation in soil, degradation of pesticides in soil, biological availability of soil-applied substances, bound residues in the soil, use of macro- and microautography, double and triple labelling, use of tracer labelling in animal experiments. (U.K.)

  13. Long-term efficacy and safety of α1 proteinase inhibitor treatment for emphysema caused by severe α1 antitrypsin deficiency

    DEFF Research Database (Denmark)

    McElvaney, Noel G; Burdon, Jonathan; Holmes, Mark

    2017-01-01

    in RAPID-OLE patients was lower in the early-start group (-1·51 g/L per year [SE 0·25] at total lung capacity [TLC]; -1·55 g/L per year [0·24] at TLC plus functional residual capacity [FRC]; and -1·60 g/L per year [0·26] at FRC) than in the delayed-start group (-2·26 g/L per year [0·27] at TLC; -2·16 g....../L per year [0·26] at TLC plus FRC, and -2·05 g/L per year [0·28] at FRC). Between months 24 and 48, the rate of lung density loss was reduced in delayed-start patients (from -2·26 g/L per year to -1·26 g/L per year), but no significant difference was seen in the rate in early-start patients during...

  14. Grazing capacity estimates: why include biomass estimates from ...

    African Journals Online (AJOL)

    Forage for ruminants in the dry season were assessed and matched with feed requirements in three villages in Zimbabwe, namely; Chiweshe, Makande and Mudzimu. Stocking rates were compared with grazing capacity to determine grazing intensities. Grazing capacities were estimated with and without crop residues to ...

  15. Handling of Solid Residues

    International Nuclear Information System (INIS)

    Medina Bermudez, Clara Ines

    1999-01-01

    The topic of solid residues is specifically of great interest and concern for the authorities, institutions and community that identify in them a true threat against the human health and the atmosphere in the related with the aesthetic deterioration of the urban centers and of the natural landscape; in the proliferation of vectorial transmitters of illnesses and the effect on the biodiversity. Inside the wide spectrum of topics that they keep relationship with the environmental protection, the inadequate handling of solid residues and residues dangerous squatter an important line in the definition of political and practical environmentally sustainable. The industrial development and the population's growth have originated a continuous increase in the production of solid residues; of equal it forms, their composition day after day is more heterogeneous. The base for the good handling includes the appropriate intervention of the different stages of an integral administration of residues, which include the separation in the source, the gathering, the handling, the use, treatment, final disposition and the institutional organization of the administration. The topic of the dangerous residues generates more expectation. These residues understand from those of pathogen type that are generated in the establishments of health that of hospital attention, until those of combustible, inflammable type, explosive, radio-active, volatile, corrosive, reagent or toxic, associated to numerous industrial processes, common in our countries in development

  16. [Residual neuromuscular blockade].

    Science.gov (United States)

    Fuchs-Buder, T; Schmartz, D

    2017-06-01

    Even small degrees of residual neuromuscular blockade, i. e. a train-of-four (TOF) ratio >0.6, may lead to clinically relevant consequences for the patient. Especially upper airway integrity and the ability to swallow may still be markedly impaired. Moreover, increasing evidence suggests that residual neuromuscular blockade may affect postoperative outcome of patients. The incidence of these small degrees of residual blockade is relatively high and may persist for more than 90 min after a single intubating dose of an intermediately acting neuromuscular blocking agent, such as rocuronium and atracurium. Both neuromuscular monitoring and pharmacological reversal are key elements for the prevention of postoperative residual blockade.

  17. TENORM: Wastewater Treatment Residuals

    Science.gov (United States)

    Water and wastes which have been discharged into municipal sewers are treated at wastewater treatment plants. These may contain trace amounts of both man-made and naturally occurring radionuclides which can accumulate in the treatment plant and residuals.

  18. Residuation in orthomodular lattices

    Directory of Open Access Journals (Sweden)

    Chajda Ivan

    2017-04-01

    Full Text Available We show that every idempotent weakly divisible residuated lattice satisfying the double negation law can be transformed into an orthomodular lattice. The converse holds if adjointness is replaced by conditional adjointness. Moreover, we show that every positive right residuated lattice satisfying the double negation law and two further simple identities can be converted into an orthomodular lattice. In this case, also the converse statement is true and the corresponence is nearly one-to-one.

  19. Characterization of Hospital Residuals

    International Nuclear Information System (INIS)

    Blanco Meza, A.; Bonilla Jimenez, S.

    1997-01-01

    The main objective of this investigation is the characterization of the solid residuals. A description of the handling of the liquid and gassy waste generated in hospitals is also given, identifying the source where they originate. To achieve the proposed objective the work was divided in three stages: The first one was the planning and the coordination with each hospital center, in this way, to determine the schedule of gathering of the waste can be possible. In the second stage a fieldwork was made; it consisted in gathering the quantitative and qualitative information of the general state of the handling of residuals. In the third and last stage, the information previously obtained was organized to express the results as the production rate per day by bed, generation of solid residuals for sampled services, type of solid residuals and density of the same ones. With the obtained results, approaches are settled down to either determine design parameters for final disposition whether for incineration, trituration, sanitary filler or recycling of some materials, and storage politics of the solid residuals that allow to determine the gathering frequency. The study concludes that it is necessary to improve the conditions of the residuals handling in some aspects, to provide the cleaning personnel of the equipment for gathering disposition and of security, minimum to carry out this work efficiently, and to maintain a control of all the dangerous waste, like sharp or polluted materials. In this way, an appreciable reduction is guaranteed in the impact on the atmosphere. (Author) [es

  20. Total iron binding capacity

    Science.gov (United States)

    ... page: //medlineplus.gov/ency/article/003489.htm Total iron binding capacity To use the sharing features on this page, please enable JavaScript. Total iron binding capacity (TIBC) is a blood test to ...

  1. PERMANENCIA Y ABANDONO EN QUÍMICA GENERAL EN LAS CARRERAS DE INGENIERÍA DE LA UNIVERSIDAD TECNOLÓGICA NACIONAL – FACULTAD REGIONAL CÓRDOBA (UTN-FRC, ARGENTINA

    Directory of Open Access Journals (Sweden)

    María C. Oliver

    2011-01-01

    Full Text Available En este trabajo se analiza el rendimiento académico en el aprendizaje de la Química que presentaron los alumnos de las carreras de Ingeniería de la Universidad Tecnológica Nacional – Facultad Regional Córdoba (UTN-FRC, así como la problemática del abandono o deserción durante el ciclo lectivo 2009. El alto porcentaje de alumnos libres y abandonos lleva a plantear la necesidad de un ciclo de nivelación más intensivo y eficaz en el área de Química, que genere una instancia de articulación que permita mejorar el paso de los jóvenes del nivel medio al universitario. La propuesta presentada en este estudio es apenas una cara de la solución, pero con dichas acciones se pretende minimizar uno de los problemas principales del ámbito universitario, tal como la alta tasa de deserción, sobre todo en los primeros años, y el fracaso de los jóvenes que comienzan la universidad.

  2. Responsibility and Capacities

    DEFF Research Database (Denmark)

    Ryberg, Jesper

    2014-01-01

    That responsible moral agency presupposes certain mental capacities, constitutes a widely accepted view among theorists. Moreover, it is often assumed that degrees in the development of the relevant capacities co-vary with degrees of responsibility. In this article it is argued that, the move from...... the view that responsibility requires certain mental capacities to the position that degrees of responsibility co-vary with degrees of the development of the mental capacities, is premature....

  3. CDMA systems capacity engineering

    CERN Document Server

    Kim, Kiseon

    2004-01-01

    This new hands-on resource tackles capacity planning and engineering issues that are crucial to optimizing wireless communication systems performance. Going beyond the system physical level and investigating CDMA system capacity at the service level, this volume is the single-source for engineering and analyzing systems capacity and resources.

  4. Management of NORM Residues

    International Nuclear Information System (INIS)

    2013-06-01

    The IAEA attaches great importance to the dissemination of information that can assist Member States in the development, implementation, maintenance and continuous improvement of systems, programmes and activities that support the nuclear fuel cycle and nuclear applications, and that address the legacy of past practices and accidents. However, radioactive residues are found not only in nuclear fuel cycle activities, but also in a range of other industrial activities, including: - Mining and milling of metalliferous and non-metallic ores; - Production of non-nuclear fuels, including coal, oil and gas; - Extraction and purification of water (e.g. in the generation of geothermal energy, as drinking and industrial process water; in paper and pulp manufacturing processes); - Production of industrial minerals, including phosphate, clay and building materials; - Use of radionuclides, such as thorium, for properties other than their radioactivity. Naturally occurring radioactive material (NORM) may lead to exposures at some stage of these processes and in the use or reuse of products, residues or wastes. Several IAEA publications address NORM issues with a special focus on some of the more relevant industrial operations. This publication attempts to provide guidance on managing residues arising from different NORM type industries, and on pertinent residue management strategies and technologies, to help Member States gain perspectives on the management of NORM residues

  5. Residual-stress measurements

    Energy Technology Data Exchange (ETDEWEB)

    Ezeilo, A.N.; Webster, G.A. [Imperial College, London (United Kingdom); Webster, P.J. [Salford Univ. (United Kingdom)

    1997-04-01

    Because neutrons can penetrate distances of up to 50 mm in most engineering materials, this makes them unique for establishing residual-stress distributions non-destructively. D1A is particularly suited for through-surface measurements as it does not suffer from instrumental surface aberrations commonly found on multidetector instruments, while D20 is best for fast internal-strain scanning. Two examples for residual-stress measurements in a shot-peened material, and in a weld are presented to demonstrate the attractive features of both instruments. (author).

  6. Characteristics and engineering properties of residual soil of volcanic deposits

    Science.gov (United States)

    Wibawa, Y. S.; Sugiarti, K.; Soebowo, E.

    2018-02-01

    Residual soil knowledge of volcanic-sedimentary rock products provides important information on the soil bearing capacity and its engineering properties. The residual soil is the result of weathering commonly found in unsaturated conditions, having varied geotechnical characteristics at each level of weathering. This paper summarizes the results of the research from the basic engineering properties of residual soil of volcanic-sedimentary rocks from several different locations. The main engineering properties of residual soil such as specific gravity, porosity, grain size, clay content (X-Ray test) and soil shear strength are performed on volcanic rock deposits. The results show that the variation of the index and engineering properties and the microstructure properties of residual soil have the correlation between the depths of weathering levels. Pore volume and pore size distribution on weathered rock profiles can be used as an indication of weathering levels in the tropics.

  7. Composition of carbonization residues

    Energy Technology Data Exchange (ETDEWEB)

    Hupfer; Leonhardt

    1943-11-27

    This report compared the composition of samples from Wesseling and Leuna. In each case the sample was a residue from carbonization of the residues from hydrogenation of the brown coal processed at the plant. The composition was given in terms of volatile components, fixed carbon, ash, water, carbon, hydrogen, oxygen, nitrogen, volatile sulfur, and total sulfur. The result of carbonization was given in terms of (ash and) coke, tar, water, gas and losses, and bitumen. The composition of the ash was given in terms of silicon dioxide, ferric oxide, aluminum oxide, calcium oxide, magnesium oxide, potassium and sodium oxides, sulfur trioxide, phosphorus pentoxide, chlorine, and titanium oxide. The most important difference between the properties of the two samples was that the residue from Wesseling only contained 4% oil, whereas that from Leuna had about 26% oil. Taking into account the total amount of residue processed yearly, the report noted that better carbonization at Leuna could save 20,000 metric tons/year of oil. Some other comparisons of data included about 33% volatiles at Leuna vs. about 22% at Wesseling, about 5 1/2% sulfur at Leuna vs. about 6 1/2% at Leuna, but about 57% ash for both. Composition of the ash differed quite a bit between the two. 1 table.

  8. Designing with residual materials

    NARCIS (Netherlands)

    Walhout, W.; Wever, R.; Blom, E.; Addink-Dölle, L.; Tempelman, E.

    2013-01-01

    Many entrepreneurial businesses have attempted to create value based on the residual material streams of third parties. Based on ‘waste’ materials they designed products, around which they built their company. Such activities have the potential to yield sustainable products. Many of such companies

  9. Sugarcane rice residue biochars and their applications

    Science.gov (United States)

    Wang, J. J.

    2014-12-01

    Sugarcane production in U.S. involves either pre-harvest burning or after-harvest burning of the residue. Approximately 70-90% of the dry matter of harvested sugarcane trash is lost through open field burning. This practice has caused considerable concerns over air quality and soil sustainability. We propose an alternative conservation approach to convert the sugarcane residue to biochar and used as soil amendment to conserve carbon and potentially improve soil fertility. In this study, fundamental properties of biochars made from sugarcane residue along with rice residues were tested for agronomic and environmental benefits. Sugarcane and rice harvest residues and milling processing byproducts bagasse and rice husk were converted to biochars at different pyrolysis temperatures and characterized. In general, sugarcane leave biochar contained more P, K, Ca and Mg than sugarcane bagasse biochar. Rice straw biochar had more S, K Ca but less P than rice husk biochar. Both biochars had higher available fraction of total P than that of total K. Sugarcane leave biochar converted at 450oC was dominated with various lignin derived phenols as well as non-specific aromatic compounds whereas bagasse biochar was with both lignin derived phenol and poly aromatic hydrocarbon (PAH). Rice straw char was dominated with non-specific aromatic compounds. At 750oC, charred material was dominated with aromatic ethers while losing the aromatic C=C structures. These molecular and surface property differences likely contributed to the difference in water holding capacities observed with these biochars. On the other hand, rice straw biochars produced at different pyrolysis temperatures had no significant effect on rice germination. Soils treated with sugarcane leave/trash biochar significantly enhanced sugarcane growth especially the root length. Treating soil with either sugarcane leave or bagasse char also enhanced soil adsorption capacity of atrazine; a common herbicide used in sugarcane

  10. Shear Capacity of Steel and Polymer Fibre Reinforced Concrete Beams

    DEFF Research Database (Denmark)

    Kragh-Poulsen, Jens C.; Hoang, Cao Linh; Goltermann, Per

    2011-01-01

    This paper deals with the application of a plasticity model for shear strength estimation of fibre reinforced concrete beams without stirrups. When using plastic theory to shear problems in structural concrete, the so-called effective strengths are introduced, usually determined by calibrating...... of the tensile stress-crack opening relationship found from wedge splitting tests. To determine the effective compressive strength of FRC, it is proposed to adopt the formula used for conventional concrete and modify it by introducing a fibre enhancement factor to describe the effect of fibres on the compressive...... softening behaviour of FRC. The enhancement factor is determined as the ratio of the areas below the stress–strain curves for FRC and for conventional concrete. The outlined approach has been verified by shear testing of beams containing no fibres, 0.5% steel fibre volume and 0.5% polymer fibre volume...

  11. Capacity Statement for Railways

    DEFF Research Database (Denmark)

    Landex, Alex

    2007-01-01

    The subject “Railway capacity” is a combination of the capacity consumption and how the capacity is utilized. The capacity utilization of railways can be divided into 4 core elements: The number of trains; the average speed; the heterogeneity of the operation; and the stability. This article desc...... trains. This is due to network effects in the railway system and due to the fact that more trains results in lower punctuality....

  12. The French capacity mechanism

    International Nuclear Information System (INIS)

    2014-01-01

    The French capacity mechanism has been design to ensure security of supply in the context of the energy transition. This energy transition challenges the electricity market design with several features: peak load growth, the development of renewables, demand response,... To ensure security of supply in this context, a capacity mechanism is being implemented in France. It is a market wide capacity obligation on electricity suppliers, based on market principles. Suppliers are responsible for forecasting their obligation, which corresponds to their contribution to winter peak load, and must procure enough capacity certificates to meet their obligations. Capacity certificates are granted to capacities through a certification process, which assesses their contribution to security of supply on the basis of availability commitments. This certification process is technology neutral and performance based, associated with controls and penalties in case of non compliance. Demand Side is fully integrated in the market, either through the reduction of suppliers' capacity obligation or direct participation after certification. In addition to the expected benefits in terms of security of supply, the French capacity market will foster the development of demand response. The participation of foreign capacities will require adaptations which are scheduled in a road-map, and could pave the way for further European integration of energy policies. (authors)

  13. Heat Capacity Analysis Report

    International Nuclear Information System (INIS)

    Findikakis, A.

    2004-01-01

    The purpose of this report is to provide heat capacity values for the host and surrounding rock layers for the waste repository at Yucca Mountain. The heat capacity representations provided by this analysis are used in unsaturated zone (UZ) flow, transport, and coupled processes numerical modeling activities, and in thermal analyses as part of the design of the repository to support the license application. Among the reports that use the heat capacity values estimated in this report are the ''Multiscale Thermohydrologic Model'' report, the ''Drift Degradation Analysis'' report, the ''Ventilation Model and Analysis Report, the Igneous Intrusion Impacts on Waste Packages and Waste Forms'' report, the ''Dike/Drift Interactions report, the Drift-Scale Coupled Processes (DST and TH Seepage) Models'' report, and the ''In-Drift Natural Convection and Condensation'' report. The specific objective of this study is to determine the rock-grain and rock-mass heat capacities for the geologic stratigraphy identified in the ''Mineralogic Model (MM3.0) Report'' (BSC 2004 [DIRS 170031], Table 1-1). This report provides estimates of the heat capacity for all stratigraphic layers except the Paleozoic, for which the mineralogic abundance data required to estimate the heat capacity are not available. The temperature range of interest in this analysis is 25 C to 325 C. This interval is broken into three separate temperature sub-intervals: 25 C to 95 C, 95 C to 114 C, and 114 C to 325 C, which correspond to the preboiling, trans-boiling, and postboiling regimes. Heat capacity is defined as the amount of energy required to raise the temperature of a unit mass of material by one degree (Nimick and Connolly 1991 [DIRS 100690], p. 5). The rock-grain heat capacity is defined as the heat capacity of the rock solids (minerals), and does not include the effect of water that exists in the rock pores. By comparison, the rock-mass heat capacity considers the heat capacity of both solids and pore

  14. Effects of obesity on lung volume and capacity in children and adolescents: a systematic review

    Directory of Open Access Journals (Sweden)

    Aline Dill Winck

    Full Text Available Abstract Objective: To assess the effects of obesity on lung volume and capacity in children and adolescents. Data source: This is a systematic review, carried out in Pubmed, Lilacs, Scielo and PEDro databases, using the following Keywords: Plethysmography; Whole Body OR Lung Volume Measurements OR Total Lung Capacity OR Functional Residual Capacity OR Residual Volume AND Obesity. Observational studies or clinical trials that assessed the effects of obesity on lung volume and capacity in children and adolescents (0-18 years without any other associated disease; in English; Portuguese and Spanish languages were selected. Methodological quality was assessed by the Agency for Healthcare Research and Quality. Data synthesis: Of the 1,030 articles, only four were included in the review. The studies amounted to 548 participants, predominantly males, with sample size ranging from 45 to 327 individuals. 100% of the studies evaluated nutritional status through BMI (z-score and 50.0% reported the data on abdominal circumference. All demonstrated that obesity causes negative effects on lung volume and capacity, causing a reduction mainly in functional residual capacity in 75.0% of the studies; in the expiratory reserve volume in 50.0% and in the residual volume in 25.0%. The methodological quality ranged from moderate to high, with 75.0% of the studies classified as having high methodological quality. Conclusions: Obesity causes deleterious effects on lung volume and capacity in children and adolescents, mainly by reducing functional residual capacity, expiratory reserve volume and residual volume.

  15. Residual stresses in material processing

    Science.gov (United States)

    Kozaczek, K. J.; Watkins, T. R.; Hubbard, C. R.; Wang, Xun-Li; Spooner, S.

    Material manufacturing processes often introduce residual stresses into the product. The residual stresses affect the properties of the material and often are detrimental. Therefore, the distribution and magnitude of residual stresses in the final product are usually an important factor in manufacturing process optimization or component life prediction. The present paper briefly discusses the causes of residual stresses. It then addresses the direct, nondestructive methods of residual stress measurement by X ray and neutron diffraction. Examples are presented to demonstrate the importance of residual stress measurement in machining and joining operations.

  16. Pesticide residues in birds and mammals

    Science.gov (United States)

    Stickel, L.F.; Edwards, C.A.

    1973-01-01

    SUMMARY: Residues of organochlorine pesticides and their breakdown products are present in the tissues of essentially all wild birds throughout the world. These chemicals accumulate in fat from a relatively small environmental exposure. DDE and dieldrin are most prevalent. Others, such as heptachlor epoxide, chlordane, endrin, and benzene hexachloride also occur, the quantities and kinds generally reflecting local or regional use. Accumulation may be sufficient to kill animals following applications for pest control. This has occurred in several large-scale programmes in the United States. Mortality has also resulted from unintentional leakage of chemical from commercial establishments. Residues may persist in the environment for many years, exposing successive generations of animals. In general, birds that eat other birds, or fish, have higher residues than those that eat seeds and vegetation. The kinetic processes of absorption, metabolism, storage, and output differ according to both kind of chemical and species of animal. When exposure is low and continuous, a balance between intake and excretion may be achieved. Residues reach a balance at an approximate animal body equilibrium or plateau; the storage is generally proportional to dose. Experiments with chickens show that dieldrin and heptachlor epoxide have the greatest propensity for storage, endrin next, then DDT, then lindane. The storage of DDT was complicated by its metabolism to DDE and DDD, but other studies show that DDE has a much greater propensity for storage than either DDD or DDT. Methoxychlor has little cumulative capacity in birds. Residues in eggs reflect and parallel those in the parent bird during accumulation, equilibrium, and decline when dosage is discontinued. Residues with the greatest propensity for storage are also lost most slowly. Rate of loss of residues can be modified by dietary components and is speeded by weight loss of the animal. Under sublethal conditions of continuous

  17. Prospects for OPEC capacity

    International Nuclear Information System (INIS)

    Adelman, M.A.

    1995-01-01

    OPEC capacity is not exogenous, but responds to demand. Price increases have not been caused by capacity shortages. OPEC nations find it hard to set aside even very small portions of their revenues for oil investment, despite its extreme profitability. Foreign investors face high risks. Production sharing makes their after-tax return even more unstable. (author)

  18. SRC Residual fuel oils

    Science.gov (United States)

    Tewari, Krishna C.; Foster, Edward P.

    1985-01-01

    Coal solids (SRC) and distillate oils are combined to afford single-phase blends of residual oils which have utility as fuel oils substitutes. The components are combined on the basis of their respective polarities, that is, on the basis of their heteroatom content, to assure complete solubilization of SRC. The resulting composition is a fuel oil blend which retains its stability and homogeneity over the long term.

  19. Composition of carbonization residues

    Energy Technology Data Exchange (ETDEWEB)

    Hupfer; Leonhardt

    1943-11-30

    This report gave a record of the composition of several samples of residues from carbonization of various hydrogenation residue from processing some type of coal or tar in the Bergius process. These included Silesian bituminous coal processed at 600 atm. with iron catalyst, in one case to produce gasoline and middle oil and in another case to produce heavy oil excess, Scholven coal processed at 250 atm. with tin oxalate and chlorine catalyst, Bruex tar processed in a 10-liter oven using iron catalyst, and a pitch mixture from Welheim processed in a 10-liter over using iron catalyst. The values gathered were compared with a few corresponding values estimated for Boehlen tar and Gelsenberg coal based on several assumptions outlined in the report. The data recorded included percentage of ash in the dry residue and percentage of carbon, hydrogen, oxygen, nitrogen, chlorine, total sulfur, and volatile sulfur. The percentage of ash varied from 21.43% in the case of Bruex tar to 53.15% in the case of one of the Silesian coals. Percentage of carbon varied from 44.0% in the case of Scholven coal to 78.03% in the case of Bruex tar. Percentage of total sulfur varied from 2.28% for Bruex tar to a recorded 5.65% for one of the Silesian coals and an estimated 6% for Boehlen tar. 1 table.

  20. Effects of twin-screw extrusion on soluble dietary fibre and physicochemical properties of soybean residue.

    Science.gov (United States)

    Jing, Yan; Chi, Yu-Jie

    2013-06-01

    Extrusion cooking technology was applied for soluble dietary fibre extraction from soybean residue. Response surface methodology (RSM) was used to optimise the effects of extrusion parameters, namely extrusion temperature (90-130°C), feed moisture (25-35%) and screw speed (160-200 rpm) on the content of soluble dietary fibre. According to the regression coefficients significance of the quadratic polynomial model, the optimum extrusion parameters were as follows: extrusion temperature, 115°C; feed moisture, 31%; and screw speed, 180 rpm. Under these conditions, the soluble dietary fibre content of soybean residue could reach to 12.65% which increased 10.60% compared with the unextruded soybean residue. In addition, the dietary fibre in extrude soybean residue had higher water retention capacity, oil retention capacity and swelling capacity than those of dietary fibre in unextruded soybean residue. Copyright © 2012 Elsevier Ltd. All rights reserved.

  1. Residual magnetic field in rotary machines; Campo magnetico residual en maquinas rotatorias

    Energy Technology Data Exchange (ETDEWEB)

    Gonzalez V, Esteban A; Apanco R, Marcelino [Instituto de Investigaciones Electricas, Cuernavaca, Morelos (Mexico)

    2007-07-01

    The residual magnetism is a phenomenon in which the magnetic dipoles of a substance are oriented in a certain degree. On the other hand, when internal forces exist capable of aligning elementary magnetic dipoles of a material, a permanent magnet is obtained. Just as in a conductor or in a material, in the elements of a rotary electrical machine magnetic fields can be induced that produce a residual magnetism or magnetization. In the rotary electrical machines, the magnetization phenomenon causes serious problems, such as the generation of induced currents that propitiate the mechanical wear in bearings, collars, trunnions and inclusive in the shaft, by effects known as pitting, frosting and spark tracks, as well as erroneous readings in vibration and temperature sensors, that in some cases can cause the shut down of the machine. In this article are presented the general concepts on the residual magnetism in rotary electrical machines, the causes that originate it and the problems that arises, as well as the demagnetization of the components that have residual magnetic field. The results obtained by the area of Electrical Equipment of the Instituto de Investigaciones Electricas are revised, during the execution of activities related to the measurement and elimination of the residual magnetic field in rotary electrical machines. [Spanish] El magnetismo residual es un fenomeno en el que los dipolos magneticos de una sustancia se encuentran orientados en un grado determinado. Por otro lado, cuando existen fuerzas internas capaces de alinear los dipolos magneticos elementales de un material, se tiene un iman permanente. Al igual que en un conductor o un material, en los elementos de una maquina electrica rotatoria se pueden inducir campos magneticos que producen un magnetismo residual o magnetizacion. En las maquinas electricas rotatorias, el fenomeno de magnetizacion causa graves problemas, como la generacion de corrientes inducidas que propician el desgaste mecanico

  2. Vedr.: Military capacity building

    DEFF Research Database (Denmark)

    Larsen, Josefine Kühnel; Struwe, Lars Bangert

    2013-01-01

    Military capacity building has increasingly become an integral part of Danish defence. Military capacity is a new way of thinking Danish defence and poses a new set of challenges and opportunities for the Danish military and the Political leadership. On the 12th of december, PhD. Candidate Josefine...... Kühnel Larsen and researcher Lars Bangert Struwe of CMS had organized a seminar in collaboration with Royal Danish Defense Colleg and the East African Security Governance Network. The seminar focused on some of the risks involved in Military capacity building and how these risks are dealt with from...

  3. Quadratic residues and non-residues selected topics

    CERN Document Server

    Wright, Steve

    2016-01-01

    This book offers an account of the classical theory of quadratic residues and non-residues with the goal of using that theory as a lens through which to view the development of some of the fundamental methods employed in modern elementary, algebraic, and analytic number theory. The first three chapters present some basic facts and the history of quadratic residues and non-residues and discuss various proofs of the Law of Quadratic Reciprosity in depth, with an emphasis on the six proofs that Gauss published. The remaining seven chapters explore some interesting applications of the Law of Quadratic Reciprocity, prove some results concerning the distribution and arithmetic structure of quadratic residues and non-residues, provide a detailed proof of Dirichlet’s Class-Number Formula, and discuss the question of whether quadratic residues are randomly distributed. The text is a valuable resource for graduate and advanced undergraduate students as well as for mathematicians interested in number theory.

  4. Capacity at Railway Stations

    DEFF Research Database (Denmark)

    Landex, Alex

    2011-01-01

    zone(s) the possible conflicts with other trains (also in the opposite direction) are taken into account leading to more trustworthy results. Although the UIC 406 methodology proposes that the railway network should be divided into line sections when trains turn around and when the train order...... is changed, this paper recommends that the railway lines are not always be divided. In case trains turn around on open (single track) line, the capacity consumption may be too low if a railway line is divided. The same can be the case if only few trains are overtaken at an overtaking station. For dead end......Stations do have other challenges regarding capacity than open lines as it is here the traffic is dispatched. The UIC 406 capacity method that can be used to analyse the capacity consumption can be exposed in different ways at stations which may lead to different results. Therefore, stations need...

  5. Visual attention capacity

    DEFF Research Database (Denmark)

    Habekost, Thomas; Starrfelt, Randi

    2009-01-01

    Psychophysical studies have identified two distinct limitations of visual attention capacity: processing speed and apprehension span. Using a simple test, these cognitive factors can be analyzed by Bundesen's Theory of Visual Attention (TVA). The method has strong specificity and sensitivity...

  6. Sharing Residual Liability

    DEFF Research Database (Denmark)

    Carbonara, Emanuela; Guerra, Alice; Parisi, Francesco

    2016-01-01

    Economic models of tort law evaluate the efficiency of liability rules in terms of care and activity levels. A liability regime is optimal when it creates incentives to maximize the value of risky activities net of accident and precaution costs. The allocation of primary and residual liability...... the virtues and limits of loss-sharing rules in generating optimal (second-best) incentives and allocations of risk. We find that loss sharing may be optimal in the presence of countervailing policy objectives, homogeneous risk avoiders, and subadditive risk, which potentially offers a valuable tool...

  7. Revisiting Absorptive Capacity

    DEFF Research Database (Denmark)

    de Araújo, Ana Luiza Lara; Ulhøi, John Parm; Lettl, Christopher

    learning processes of absorptive capacity, which comprise combinative and adaptive capabilities. Drawing on survey data (n=169), the study concludes that combinative capabilities primarily enhance transformative and exploratory learning processes, while adaptive capabilities strengthen all three learning......Absorptive capacity has mostly been perceived as a 'passive' outcome of R&D investments. Recently, however, a growing interest into its 'proactive' potentials has emerged. This paper taps into this development and proposes a dynamic model for conceptualizing the determinants of the complementary...

  8. Hyperpolarized 3He apparent diffusion coefficient MRI of the lung: reproducibility and volume dependency in healthy volunteers and patients with emphysema

    DEFF Research Database (Denmark)

    Diaz, S.; Casselbrant, I.; Piitulainen, E.

    2008-01-01

    patients with emphysema were examined after inhalation of HP (3)He gas mixed with nitrogen (N(2)) during breathhold starting from functional residual capacity (FRC) in supine position. Coronal diffusion-sensitized MR images were acquired. Each subject was imaged on three separate days over a seven...

  9. Material properties of frc with recycled aggregate

    Czech Academy of Sciences Publication Activity Database

    Trčková, Jiřina; Procházka, P.

    2011-01-01

    Roč. 8, č. 2 (2011), s. 105-113 ISSN 1214-9705 R&D Projects: GA ČR GA103/08/1197 Institutional research plan: CEZ:AV0Z30460519 Keywords : recycled aggregate * concrete composite * pullout test Subject RIV: JM - Building Engineering Impact factor: 0.530, year: 2011 http://www.irsm.cas.cz/abstracts/AGG/02_11/1_Trckova.pdf

  10. Realization of FRC interior and exterior furniture

    Science.gov (United States)

    Šonka, Š.; Frantová, M.; Štemberk, P.; Havrda, J.; Janouch, P.

    2017-09-01

    This article deals with the implementation of fibre reinforced concrete for interior and exterior furniture. The use of fibre reinforced concrete for non-traditional and small structures brings some specifics in design and realization. These are, in particular, the design of a suitable mixture, the choice of the shape of the structure in relation to the technological possibilities of realization, the static effects and finally the actual production of the element.

  11. Interface Properties in Extruded FRC-Materials

    DEFF Research Database (Denmark)

    Stang, Henrik

    1997-01-01

    reinforced cementitious material extruded by the developed process. It is further more shown that the fiber-matrix bond is highly dependent on the relative slip at the interface and a bond-slip relationship is suggested for the extruded material. The observed very high fiber-matrix bond is explained...

  12. A program of FRC theory research

    International Nuclear Information System (INIS)

    Krall, N.A.

    1990-01-01

    At the request of the Office of Fusion Energy, a group of experts was convened on February 6--8, 1990. This group met to assess the world data base on Reversed Field Pinch (RFP) physics, and, further, to assess the role of the ZTH experiment in providing reactor relevant physics understanding for that confinement geometry. This group met, analyzed some of the relevant literature, and heard extensive presentations on the physics of the RFP and the plans for the ZTH and RFX devices. The conclusions of this group of experts are contained in this report

  13. Manual of Standard Operating Procedures for Veterinary Drug Residue Analysis

    International Nuclear Information System (INIS)

    2016-01-01

    Laboratories are crucial to national veterinary drug residue monitoring programmes. However, one of the main challenges laboratories encounter is obtaining access to relevant methods of analysis. Thus, in addition to training, providing technical advice and transferring technology, the Joint FAO/IAEA Division of Nuclear Techniques in Food and Agriculture has resolved to develop clear and practical manuals to support Member State laboratories. The Coordinated Research Project (CRP) on Development of Radiometric and Allied Analytical Methods to Strengthen Residue Control Programs for Antibiotic and Anthelmintic Veterinary Drug Residues has developed a number of analytical methods as standard operating procedures (SOPs), which are now compiled here. This publication contains SOPs on chromatographic and spectrometric techniques, as well as radioimmunoassay and associated screening techniques, for various anthelmintic and antimicrobial veterinary drug residue analysis. Some analytical method validation protocols are also included. The publication is primarily aimed at food and environmental safety laboratories involved in testing veterinary drug residues, including under organized national residue monitoring programmes. It is expected to enhance laboratory capacity building and competence through the use of radiometric and complementary tools and techniques. The publication is also relevant for applied research on residues of veterinary drugs in food and environmental samples

  14. Dual capacity reciprocating compressor

    Science.gov (United States)

    Wolfe, Robert W.

    1984-01-01

    A multi-cylinder compressor 10 particularly useful in connection with northern climate heat pumps and in which different capacities are available in accordance with reversing motor 16 rotation is provided with an eccentric cam 38 on a crank pin 34 under a fraction of the connecting rods, and arranged for rotation upon the crank pin between opposite positions 180.degree. apart so that with cam rotation on the crank pin such that the crank throw is at its normal maximum value all pistons pump at full capacity, and with rotation of the crank shaft in the opposite direction the cam moves to a circumferential position on the crank pin such that the overall crank throw is zero. Pistons 24 whose connecting rods 30 ride on a crank pin 36 without a cam pump their normal rate with either crank rotational direction. Thus a small clearance volume is provided for any piston that moves when in either capacity mode of operation.

  15. Geothermal Plant Capacity Factors

    Energy Technology Data Exchange (ETDEWEB)

    Greg Mines; Jay Nathwani; Christopher Richard; Hillary Hanson; Rachel Wood

    2015-01-01

    The capacity factors recently provided by the Energy Information Administration (EIA) indicated this plant performance metric had declined for geothermal power plants since 2008. Though capacity factor is a term commonly used by geothermal stakeholders to express the ability of a plant to produce power, it is a term frequently misunderstood and in some instances incorrectly used. In this paper we discuss how this capacity factor is defined and utilized by the EIA, including discussion on the information that the EIA requests from operations in their 923 and 860 forms that are submitted both monthly and annually by geothermal operators. A discussion is also provided regarding the entities utilizing the information in the EIA reports, and how those entities can misinterpret the data being supplied by the operators. The intent of the paper is to inform the facility operators as the importance of the accuracy of the data that they provide, and the implications of not providing the correct information.

  16. Value for railway capacity

    DEFF Research Database (Denmark)

    Sameni, Melody Khadem; Preston, John M.

    2012-01-01

    to analyze the efficiency of operators in transforming inputs of allocated capacity of infrastructure and franchise payments into valuable passenger service outputs while avoiding delays. By addressing operational and economic aspects of capacity utilization simultaneously, the paper deviates from existing...... DEA work on the economic efficiency of railways by considering a new combination of input-output that also incorporates quality of service. The constant and variable returns to scale models are applied to the case study of franchised passenger operators in Great Britain. The follow-up Tobit regression...

  17. Marine Tar Residues: a Review

    OpenAIRE

    Warnock, April M.; Hagen, Scott C.; Passeri, Davina L.

    2015-01-01

    Marine tar residues originate from natural and anthropogenic oil releases into the ocean environment and are formed after liquid petroleum is transformed by weathering, sedimentation, and other processes. Tar balls, tar mats, and tar patties are common examples of marine tar residues and can range in size from millimeters in diameter (tar balls) to several meters in length and width (tar mats). These residues can remain in the ocean environment indefinitely, decomposing or becoming buried in ...

  18. Evaluation of railway capacity

    DEFF Research Database (Denmark)

    Landex, Alex; Kaas, Anders H.; Schittenhelm, Bernd

    2006-01-01

    capacity consumptions. This paper describes the UIC 406 method and how it is expounded in Denmark. The paper describes the importance of choosing the right length of the line sections examined and how line sections with multiple track sections are examined. Furthermore, the possibility of using idle...

  19. Building capacity in Benin

    International Development Research Centre (IDRC) Digital Library (Canada)

    sigp1. Building capacity in. Benin. Training of technical staff of municipalities in the Okpara Basin of Benin in the use of GIS tools for water management, hydrological .... Practical exercises allowed participants to define the catchment area of the ...

  20. Evaluation of residue-residue contact predictions in CASP9

    KAUST Repository

    Monastyrskyy, Bohdan

    2011-01-01

    This work presents the results of the assessment of the intramolecular residue-residue contact predictions submitted to CASP9. The methodology for the assessment does not differ from that used in previous CASPs, with two basic evaluation measures being the precision in recognizing contacts and the difference between the distribution of distances in the subset of predicted contact pairs versus all pairs of residues in the structure. The emphasis is placed on the prediction of long-range contacts (i.e., contacts between residues separated by at least 24 residues along sequence) in target proteins that cannot be easily modeled by homology. Although there is considerable activity in the field, the current analysis reports no discernable progress since CASP8.

  1. Pulmonary Function Measures before and after Exposure of Human Subjects to +G(z) and +G(x) Acceleration Loads.

    Science.gov (United States)

    1981-09-28

    lung capacity) is reduced by 37 percent, VC (vital capacity) by 44 percent, and FRC (func- tional residual capacity) by 32 percent, the elastic recoil ...been reported that after strapping has been removed from the chest, subjects continue to show increased elastic recoil pressure and expired flow rates...supine body positions, the lungs have been shown to be particularly susceptible to changes in applied G loads. Unlike any other tissues in the body, the

  2. Landfilling of waste incineration residues

    DEFF Research Database (Denmark)

    Christensen, Thomas Højlund; Astrup, Thomas; Cai, Zuansi

    2002-01-01

    Residues from waste incineration are bottom ashes and air-pollution-control (APC) residues including fly ashes. The leaching of heavy metals and salts from the ashes is substantial and a wide spectrum of leaching tests and corresponding criteria have been introduced to regulate the landfilling...

  3. Statistical inference on residual life

    CERN Document Server

    Jeong, Jong-Hyeon

    2014-01-01

    This is a monograph on the concept of residual life, which is an alternative summary measure of time-to-event data, or survival data. The mean residual life has been used for many years under the name of life expectancy, so it is a natural concept for summarizing survival or reliability data. It is also more interpretable than the popular hazard function, especially for communications between patients and physicians regarding the efficacy of a new drug in the medical field. This book reviews existing statistical methods to infer the residual life distribution. The review and comparison includes existing inference methods for mean and median, or quantile, residual life analysis through medical data examples. The concept of the residual life is also extended to competing risks analysis. The targeted audience includes biostatisticians, graduate students, and PhD (bio)statisticians. Knowledge in survival analysis at an introductory graduate level is advisable prior to reading this book.

  4. Automatic prediction of catalytic residues by modeling residue structural neighborhood

    Directory of Open Access Journals (Sweden)

    Passerini Andrea

    2010-03-01

    Full Text Available Abstract Background Prediction of catalytic residues is a major step in characterizing the function of enzymes. In its simpler formulation, the problem can be cast into a binary classification task at the residue level, by predicting whether the residue is directly involved in the catalytic process. The task is quite hard also when structural information is available, due to the rather wide range of roles a functional residue can play and to the large imbalance between the number of catalytic and non-catalytic residues. Results We developed an effective representation of structural information by modeling spherical regions around candidate residues, and extracting statistics on the properties of their content such as physico-chemical properties, atomic density, flexibility, presence of water molecules. We trained an SVM classifier combining our features with sequence-based information and previously developed 3D features, and compared its performance with the most recent state-of-the-art approaches on different benchmark datasets. We further analyzed the discriminant power of the information provided by the presence of heterogens in the residue neighborhood. Conclusions Our structure-based method achieves consistent improvements on all tested datasets over both sequence-based and structure-based state-of-the-art approaches. Structural neighborhood information is shown to be responsible for such results, and predicting the presence of nearby heterogens seems to be a promising direction for further improvements.

  5. Seismic capacity of switchgear

    International Nuclear Information System (INIS)

    Bandyopadhyay, K.; Hofmayer, C.; Kassir, M.; Pepper, S.

    1989-01-01

    As part of a component fragility program sponsored by the USNRC, BNL has collected existing information on the seismic capacity of switchgear assemblies from major manufacturers. Existing seismic test data for both low and medium voltage switchgear assemblies have been evaluated and the generic results are presented in this paper. The failure modes are identified and the corresponding generic lower bound capacity levels are established. The test response spectra have been used as a measure of the test vibration input. The results indicate that relays chatter at a very low input level at the base of the switchgear cabinet. This change of state of devices including relays have been observed. Breaker tripping occurs at a higher vibration level. Although the structural failure of internal elements have been noticed, the overall switchgear cabinet structure withstands a high vibration level. 5 refs., 2 figs., 2 tabs

  6. Absorptive Capacity and Diversity

    DEFF Research Database (Denmark)

    Kristinsson, Kári

    international business, organizational economics, strategic management, technology management and last but not least neo-Schumpeterian economics. The goal of this dissertation is to examine what many consider as neglected arguments from the work by Cohen and Levinthal and thereby illuminate an otherwise......One of the most influential contributions to neo-Schumpeterian economics is Cohen and Levinthal‘s papers on absorptive capacity. Since their publication in the late 1980s and early 1990s the concept absorptive capacity has had substantial impact on research in economics and management, including...... overlooked area of research. Although research based on Cohen and Levinthal‘s work has made considerable impact, there is scarcity of research on certain fundamental points argued by Cohen and Levinthal. Among these is the importance of employee diversity as well as the type and nature of interaction between...

  7. Heat Capacity Mapping Mission

    Science.gov (United States)

    Nilsson, C. S.; Andrews, J. C.; Scully-Power, P.; Ball, S.; Speechley, G.; Latham, A. R. (Principal Investigator)

    1980-01-01

    The Tasman Front was delineated by airborne expendable bathythermograph survey; and an Heat Capacity Mapping Mission (HCMM) IR image on the same day shows the same principal features as determined from ground-truth. It is clear that digital enhancement of HCMM images is necessary to map ocean surface temperatures and when done, the Tasman Front and other oceanographic features can be mapped by this method, even through considerable scattered cloud cover.

  8. CSTI High Capacity Power

    International Nuclear Information System (INIS)

    Winter, J.M.

    1989-01-01

    The SP-100 program was established in 1983 by DOD, DOE, and NASA as a joint program to develop the technology necessary for space nuclear power systems for military and civil application. During FY-86 and 87, the NASA SP-100 Advanced Technology Program was devised to maintain the momentum of promising technology advancement efforts started during Phase 1 of SP-100 and to strengthen, in key areas, the chances for successful development and growth capability of space nuclear reactor power systems for future space applications. In FY-88, the Advanced Technology Program was incorporated into NASA's new Civil Space Technology Initiative (CSTI). The CSTI Program was established to provide the foundation for technology development in automation and robotics, information, propulsion, and power. The CSTI High Capacity Power Program builds on the technology efforts of the SP-100 program, incorporates the previous NASA SP-100 Advanced Technology project, and provides a bridge to NASA Project Pathfinder. The elements of CSTI High Capacity Power development include Conversion Systems, Thermal Management, Power Management, System Diagnostics, and Environmental Interactions. Technology advancement in all areas, including materials, is required to assure the high reliability and 7 to 10 year lifetime demanded for future space nuclear power systems. The overall program will develop and demonstrate the technology base required to provide a wide range of modular power systems as well as allowing mission independence from solar and orbital attitude requirements. Several recent advancements in CSTI High Capacity power development will be discussed

  9. Thermal analysis of an enriched flame incinerator for aqueous residues

    Energy Technology Data Exchange (ETDEWEB)

    Lacava, Pedro Teixeira; Pimenta, Amilcar Porto [Divisao de Engenharia Aeronautica, Instituto Tecnologico de Aeronautica, Pca. Mal. Eduardo Gomes, 50, Vila das Acacias, 12228-900, Sao Jose dos Campos, SP (Brazil); Carvalho, Joao A. [Departamento de Energia, Campus de Guaratingueta, Universidade Estadual Paulista, Av. Dr. Ariberto Pereira da Cunha, 333, 12516-410, Guaratingueta, SP (Brazil); Ferreira, Marco Aurelio [Laboratorio Associado de Combustao e Propulsao, Instituto Nacional de Pesquisas Espaciais, Rod. Presidente Dutra, km 40, 12630-000, Cachoeira Paulista, SP (Brazil)

    2006-03-01

    The use of oxygen to enrich the combustion air can be an attractive technique to increase capacity of an incinerator originally designed to operate with air. If incinerator parameters such as operation temperature, turbulence level and residence time are fixed for a certain fuel supply rate, it is possible to increase the residue consumption rate using enriched air. This paper presents the thermal analysis for operation with enriched air of an aqueous residue experimental incinerator. The auxiliary fuel was diesel oil. The theoretical results showed that there is a considerable increase in the incineration ratio up to approximately 50% of O{sub 2} in the oxidiser. The tendency was confirmed experimentally. Thermal analysis was demonstrated to be an important tool to predict possible incinerator capacity increase. (author)

  10. Competence building capacity shortage

    International Nuclear Information System (INIS)

    Doorman, Gerard; Wangensteen, Ivar; Bakken, Bjoern

    2005-02-01

    The objective of the project 'Competence Building Capacity Shortage' has been 'to increase knowledge about central approaches aimed at solving the peaking capacity problem in restructured power systems'. With respect to reserve markets, a model was developed in the project to analyze the relations between reserve requirements and prices in the spot and reserve markets respectively. A mathematical model was also developed and implemented, which also includes the balance market, and has a good ability to predict the relations between these markets under various assumptions. With some further development, this model can be used fore realistic analyses of these markets in a Nordic context. It was also concluded that certain system requirements with respect to frequency and time deviation can be relaxed without adverse effects. However, the requirements to system bias, Frequency Activated Operating Reserves and Frequency Activated Contingency Reserves cannot be relaxed, the latter because they must cover the dimensioning fault in the system. On the other hand, Fast Contingency Reserves can be reduced by removing requirements to national balances. Costs can furthermore be reduced by increasingly adapting a Nordic as opposed to national approach. A model for stepwise power flow was developed in the project, which is especially useful to analyze slow power system dynamics. This is relevant when analysing the effects of reserve requirements. A model for the analysis of the capacity balance in Norway and Sweden was also developed. This model is useful for looking at the future balance under various assumptions regarding e.g. weather conditions, demand growth and the development of the generation system. With respect to the present situation, if there is some price flexibility on the demand side and system operators are able to use reserves from the demand side, the probability for load shedding during the peak load hour is close to zero under the weather conditions after

  11. Impact of diverse soil microbial communities on crop residues decomposition

    Science.gov (United States)

    Mrad, Fida; Bennegadi-Laurent, Nadia; Ailhas, Jérôme; Leblanc, Nathalie; Trinsoutrot-Gattin, Isabelle; Laval, Karine; Gattin, Richard

    2017-04-01

    Soils provide many basic ecosystem services for our society and most of these services are carried out by the soil communities, thus influencing soils quality. Soil organic matter (SOM) can be considered as one of the most important soil quality indices for it plays a determinant role in many physical, chemical and biological processes, such as soil structure and erosion resistance, cation exchange capacity, nutrient cycling and biological activity (Andrews et al., 2004). Since a long time, exogenous organic inputs are largely used for improving agricultural soils, affecting highly soil fertility and productivity. The use of organic amendments such as crop residues influences the soil microbial populations' diversity and abundance. In the meantime, soil microbial communities play a major role in the organic matter degradation, and the effect of different microbial communities on the decomposition of crop residues is not well documented. In this context, studying the impact of crop residues on soil microbial ecology and the processes controlling the fate of plant residues in different management practices is essential for understanding the long-term environmental and agronomic effects on soil and organic matters. Our purpose in the present work was to investigate the decomposition by two contrasting microbial communities of three crop residues, and compare the effect of different residues amendments on the abundance and function of each soil microbial communities. Among the main crops which produce large amounts of residues, we focused on three different plants: wheat (Triticum aestivum L.), rape (Brassica napus) and sunflower (Helianthus annuus). The residues degradation in two soils of different management practices and the microbial activity were evaluated by: microbial abundance (microbial carbon, culturable bacteria, total DNA, qPCR), in combination with functional indicators (enzymatic assays and Biolog substrate utilization), kinetics of C and N

  12. Residual stress by repair welds

    International Nuclear Information System (INIS)

    Mochizuki, Masahito; Toyoda, Masao

    2003-01-01

    Residual stress by repair welds is computed using the thermal elastic-plastic analysis with phase-transformation effect. Coupling phenomena of temperature, microstructure, and stress-strain fields are simulated in the finite-element analysis. Weld bond of a plate butt-welded joint is gouged and then deposited by weld metal in repair process. Heat source is synchronously moved with the deposition of the finite-element as the weld deposition. Microstructure is considered by using CCT diagram and the transformation behavior in the repair weld is also simulated. The effects of initial stress, heat input, and weld length on residual stress distribution are studied from the organic results of numerical analysis. Initial residual stress before repair weld has no influence on the residual stress after repair treatment near weld metal, because the initial stress near weld metal releases due to high temperature of repair weld and then stress by repair weld regenerates. Heat input has an effect for residual stress distribution, for not its magnitude but distribution zone. Weld length should be considered reducing the magnitude of residual stress in the edge of weld bead; short bead induces high tensile residual stress. (author)

  13. RESIDUAL RISK ASSESSMENT: ETHYLENE OXIDE ...

    Science.gov (United States)

    This document describes the residual risk assessment for the Ethylene Oxide Commercial Sterilization source category. For stationary sources, section 112 (f) of the Clean Air Act requires EPA to assess risks to human health and the environment following implementation of technology-based control standards. If these technology-based control standards do not provide an ample margin of safety, then EPA is required to promulgate addtional standards. This document describes the methodology and results of the residual risk assessment performed for the Ethylene Oxide Commercial Sterilization source category. The results of this analyiss will assist EPA in determining whether a residual risk rule for this source category is appropriate.

  14. Study of stiffness and bearing capacity degradation of reinforced concrete beams under constant-amplitude fatigue.

    Science.gov (United States)

    Liu, Fangping; Zhou, Jianting; Yan, Lei

    2018-01-01

    For a reinforced concrete beam subjected to fatigue loads, the structural stiffness and bearing capacity will gradually undergo irreversible degeneration, leading to damage. Moreover, there is an inherent relationship between the stiffness and bearing capacity degradation and fatigue damage. In this study, a series of fatigue tests are performed to examine the degradation law of the stiffness and bearing capacity. The results pertaining to the stiffness show that the stiffness degradation of a reinforced concrete beam exhibits a very clear monotonic decreasing "S" curve, i.e., the stiffness of the beam decreases significantly at the start of the fatigue loading, it undergoes a linear decline phase in the middle for a long loading period, and before the failure, the bearing capacity decreases drastically again. The relationship between the residual stiffness and residual bearing capacity is determined based on the assumption that the residual stiffness and residual bearing capacity depend on the same damage state, and then, the bearing capacity degradation model of the reinforced concrete beam is established based on the fatigue stiffness. Through the established model and under the premise of the known residual stiffness degradation law, the degradation law of the bearing capacity is determined by using at least one residual bearing capacity test data, for which the parameters of the stiffness degradation function are considered as material constants. The results of the bearing capacity show that the bearing capacity degradation of the reinforced concrete beam also exhibits a very clear monotonic decreasing "S" curve, which is consistent with the stiffness degradation process and in good agreement with the experiment. In this study, the stiffness and bearing capacity degradation expressions are used to quantitatively describe their occurrence in reinforced concrete beams. In particular, the expression of the bearing capacity degradation can mitigate numerous

  15. 1992 Annual Capacity Report

    International Nuclear Information System (INIS)

    1993-05-01

    The Standard Contract for Disposal of Spent Nuclear Fuel and/or High-Level Radioactive Waste (10 CFR Part 961) requires the Department of Energy (DOE) to issue an Annual Capacity Report (ACR) for planning purposes. This report is the fifth in the series published by DOE. In May 1993, DOE published the 1992 Acceptance Priority Ranking (APR) that established the order in which DOE will allocate projected acceptance capacity. As required by the Standard Contract, the acceptance priority ranking is based on the date the spent nuclear fuel (SNF) was permanently discharged, with the owners of the oldest SNF, on an industry-wide basis, given the highest priority. The 1992 ACR applies the projected waste acceptance rates in Table 2.1 to the 1992 APR, resulting in individual allocations for the owners and generators of the SNF. These allocations are listed in detail in the Appendix, and summarized in Table 3.1. The projected waste acceptance rates for SNF presented in Table 2.1 are nominal and assume a site for a Monitored Retrievable Storage (MRS) facility will be obtained; the facility will initiate operations in 1998; and the statutory linkages between the MRS facility and the repository set forth in the Nuclear Waste Policy Act of 1982, as amended (NWPA), will be modified. During the first ten years following projected commencement of Civilian Radioactive Waste Management System (CRWMS) operation, the total quantity of SNF that could be accepted is projected to be 8,200 metric tons of uranium (MTU). This is consistent with the storage capacity licensing conditions imposed on an MRS facility by the NWPA. The annual acceptance rates provide an approximation of the system throughput and are subject to change as the program progresses

  16. Quantum reading capacity

    International Nuclear Information System (INIS)

    Pirandola, Stefano; Braunstein, Samuel L; Lupo, Cosmo; Mancini, Stefano; Giovannetti, Vittorio

    2011-01-01

    The readout of a classical memory can be modelled as a problem of quantum channel discrimination, where a decoder retrieves information by distinguishing the different quantum channels encoded in each cell of the memory (Pirandola 2011 Phys. Rev. Lett. 106 090504). In the case of optical memories, such as CDs and DVDs, this discrimination involves lossy bosonic channels and can be remarkably boosted by the use of nonclassical light (quantum reading). Here we generalize these concepts by extending the model of memory from single-cell to multi-cell encoding. In general, information is stored in a block of cells by using a channel-codeword, i.e. a sequence of channels chosen according to a classical code. Correspondingly, the readout of data is realized by a process of ‘parallel’ channel discrimination, where the entire block of cells is probed simultaneously and decoded via an optimal collective measurement. In the limit of a large block we define the quantum reading capacity of the memory, quantifying the maximum number of readable bits per cell. This notion of capacity is nontrivial when we suitably constrain the physical resources of the decoder. For optical memories (encoding bosonic channels), such a constraint is energetic and corresponds to fixing the mean total number of photons per cell. In this case, we are able to prove a separation between the quantum reading capacity and the maximum information rate achievable by classical transmitters, i.e. arbitrary classical mixtures of coherent states. In fact, we can easily construct nonclassical transmitters that are able to outperform any classical transmitter, thus showing that the advantages of quantum reading persist in the optimal multi-cell scenario. (paper)

  17. Geostationary orbit capacity study

    Science.gov (United States)

    Hansell, P. S.; Norris, P.; Walton, R.

    1982-04-01

    Factors influencing the communications satellite capacity of the geostationary orbit were analyzed to derive an interference model of the orbit environment. Comparison of the total orbit arc length required by each proposed planning method or by using different technology developments indicates that the orbit arc of most interest to Western Europe will not be saturated by the year 2000. The orbit arc occupied in the year 2000 by the satellites in the West European arc of interest can be approximately halved by using digital modulation techniques for TV program transfers which use FM at present, or by adopting an orbital planning method which assigns FM TV services to predefined orbit or spectrum segments.

  18. Assessing plant residue decomposition in soil using DRIFT spectroscopy

    Science.gov (United States)

    Ouellette, Lance; Van Eerd, Laura; Voroney, Paul

    2016-04-01

    Assessment of the decomposition of plant residues typically involves the use of tracer techniques combined with measurements of soil respiration. This laboratory study evaluated use of Diffuse Reflectance Fourier Transform (DRIFT) spectroscopy for its potential to assess plant residue decomposition in soil. A sandy loam soil (Orthic Humic Gleysol) obtained from a field research plot was passed through a 4.75 mm sieve moist (~70% of field capacity) to remove larger crop residues. The experimental design consisted of a randomized complete block with four replicates of ten above-ground cover crop residue-corn stover combinations, where sampling time was blocked. Two incubations were set up for 1) Drift analysis: field moist soil (250 g ODW) was placed in 500 mL glass jars, and 2) CO2 evolution: 100 g (ODW) was placed in 2 L jars. Soils were amended with the plant residues (oven-dried at 60°C and ground to <2 mm) at rates equivalent to field mean above-ground biomass yields, then moistened to 60% water holding capacity and incubated in the dark at 22±3°C. Measurements for DRIFT and CO2-C evolved were taken after 0.5, 2, 4, 7, 10, 15, 22, 29, 36, 43, 50 64 and 72 d. DRIFT spectral data (100co-added scans per sample) were recorded with a Varian Cary 660 FT-IR Spectrometer equipped with an EasiDiff Diffuse Reflectance accessory operated at a resolution of 4 cm-1 over the mid-infrared spectrum from 4000 to 400 cm-1. DRIFT spectra of amended soils indicated peak areas of aliphatics at 2930 cm-1, of aromatics at 1620, and 1530 cm-1 and of polysaccharides at 1106 and 1036 cm-1. Evolved CO2 was measured by the alkali trap method (1 M NaOH); the amount of plant residue-C remaining in soil was calculated from the difference in the quantity of plant residue C added and the additional CO2-C evolved from the amended soil. First-order model parameters of the change in polysaccharide peak area over the incubation were related to those generated from the plant residue C decay

  19. Nitrogen availability of biogas residues

    Energy Technology Data Exchange (ETDEWEB)

    El-Sayed Fouda, Sara

    2011-09-07

    The objectives of this study were to characterize biogas residues either unseparated or separated into a liquid and a solid phase from the fermentation of different substrates with respect to their N and C content. In addition, short and long term effects of the application of these biogas residues on the N availability and N utilization by ryegrass was investigated. It is concluded that unseparated or liquid separated biogas residues provide N at least corresponding to their ammonium content and that after the first fertilizer application the C{sub org}:N{sub org} ratio of the biogas residues was a crucial factor for the N availability. After long term application, the organic N accumulated in the soil leads to an increased release of N.

  20. Residual stress analysis: a review

    International Nuclear Information System (INIS)

    Finlayson, T.R.

    1983-01-01

    The techniques which are or could be employed to measure residual stresses are outlined. They include X-ray and neutron diffraction. Comments are made on the reliability and accuracy to be expected from particular techniques

  1. OECD Maximum Residue Limit Calculator

    Science.gov (United States)

    With the goal of harmonizing the calculation of maximum residue limits (MRLs) across the Organisation for Economic Cooperation and Development, the OECD has developed an MRL Calculator. View the calculator.

  2. Effects of obesity on lung volume and capacity in children and adolescents: a systematic review.

    Science.gov (United States)

    Winck, Aline Dill; Heinzmann-Filho, João Paulo; Soares, Rafaela Borges; da Silva, Juliana Severo; Woszezenki, Cristhiele Taís; Zanatta, Letiane Bueno

    2016-12-01

    To assess the effects of obesity on lung volume and capacity in children and adolescents. This is a systematic review, carried out in Pubmed, Lilacs, Scielo and PEDro databases, using the following Keywords: Plethysmography; Whole Body OR Lung Volume Measurements OR Total Lung Capacity OR Functional Residual Capacity OR Residual Volume AND Obesity. Observational studies or clinical trials that assessed the effects of obesity on lung volume and capacity in children and adolescents (0-18 years) without any other associated disease; in English; Portuguese and Spanish languages were selected. Methodological quality was assessed by the Agency for Healthcare Research and Quality. Of the 1,030 articles, only four were included in the review. The studies amounted to 548 participants, predominantly males, with sample size ranging from 45 to 327 individuals. 100% of the studies evaluated nutritional status through BMI (z-score) and 50.0% reported the data on abdominal circumference. All demonstrated that obesity causes negative effects on lung volume and capacity, causing a reduction mainly in functional residual capacity in 75.0% of the studies; in the expiratory reserve volume in 50.0% and in the residual volume in 25.0%. The methodological quality ranged from moderate to high, with 75.0% of the studies classified as having high methodological quality. Obesity causes deleterious effects on lung volume and capacity in children and adolescents, mainly by reducing functional residual capacity, expiratory reserve volume and residual volume. Copyright © 2016 Sociedade de Pediatria de São Paulo. Publicado por Elsevier Editora Ltda. All rights reserved.

  3. Deficiency of employability capacity

    Directory of Open Access Journals (Sweden)

    Pelse I.

    2012-10-01

    Full Text Available Young unemployed people have comprised one of the significantly largest groups of the unemployed people in Latvia in recent years. One of the reasons why young people have difficulty integrating into the labour market is the “expectation gap” that exists in the relations between employers and the new generation of workers. Employers focus on capacity-building for employability such individual factors as strength, patience, self-discipline, self-reliance, self-motivation, etc., which having a nature of habit and are developed in a long-term work socialization process, which begins even before the formal education and will continue throughout the life cycle. However, when the socialization is lost, these habits are depreciated faster than they can be restored. Currently a new generation is entering the labour market, which is missing the succession of work socialization. Factors, such as rising unemployment and poverty in the background over the past twenty years in Latvia have created a very unfavourable employability background of “personal circumstances” and “external factors”, which seriously have impaired formation of the skills and attitudes in a real work environment. The study reveals another paradox – the paradox of poverty. Common sense would want to argue that poverty can be overcome by the job. However, the real state of affairs shows that unfavourable coincidence of the individual, personal circumstances and external factors leads to deficit of employability capacity and possibility of marked social and employment deprivation.

  4. Vesícula residual

    Directory of Open Access Journals (Sweden)

    Júlio C. U. Coelho

    Full Text Available Our objective is to report three patients with recurrent severe upper abdominal pain secondary to residual gallbladder. All patients had been subjected to cholecystectomy from 1 to 20 years before. The diagnosis was established after several episodes of severe upper abdominal pain by imaging exams: ultrasonography, tomography, or endoscopic retrograde cholangiography. Removal of the residual gallbladder led to complete resolution of symptoms. Partial removal of the gallbladder is a very rare cause of postcholecystectomy symptoms.

  5. Marine Tar Residues: a Review.

    Science.gov (United States)

    Warnock, April M; Hagen, Scott C; Passeri, Davina L

    Marine tar residues originate from natural and anthropogenic oil releases into the ocean environment and are formed after liquid petroleum is transformed by weathering, sedimentation, and other processes. Tar balls, tar mats, and tar patties are common examples of marine tar residues and can range in size from millimeters in diameter (tar balls) to several meters in length and width (tar mats). These residues can remain in the ocean environment indefinitely, decomposing or becoming buried in the sea floor. However, in many cases, they are transported ashore via currents and waves where they pose a concern to coastal recreation activities, the seafood industry and may have negative effects on wildlife. This review summarizes the current state of knowledge on marine tar residue formation, transport, degradation, and distribution. Methods of detection and removal of marine tar residues and their possible ecological effects are discussed, in addition to topics of marine tar research that warrant further investigation. Emphasis is placed on benthic tar residues, with a focus on the remnants of the Deepwater Horizon oil spill in particular, which are still affecting the northern Gulf of Mexico shores years after the leaking submarine well was capped.

  6. Workshop on moisture buffer capacity

    DEFF Research Database (Denmark)

    2003-01-01

    Summary report of a Nordtest workshop on moisture buffer capacity held at Copenhagen August 21-22 2003......Summary report of a Nordtest workshop on moisture buffer capacity held at Copenhagen August 21-22 2003...

  7. Building a capacity building manual

    CSIR Research Space (South Africa)

    Clinton, DD

    2010-02-01

    Full Text Available ? Capacity building in developed nations ? renewal stage HOW can capacity be developed and maintained? Through mentoring , training, education, physical projects, the infusion of financial and other resources and more importantly the motivation...

  8. Normal spectrum of pulmonary parametric response map to differentiate lung collapsibility: distribution of densitometric classifications in healthy adult volunteers

    International Nuclear Information System (INIS)

    Silva, Mario; Nemec, Stefan F.; Dufresne, Valerie; Occhipinti, Mariaelena; Heidinger, Benedikt H.; Bankier, Alexander A.; Chamberlain, Ryan

    2016-01-01

    Pulmonary parametric response map (PRM) was proposed for quantitative densitometric phenotypization of chronic obstructive pulmonary disease. However, little is known about this technique in healthy subjects. The purpose of this study was to describe the normal spectrum of densitometric classification of pulmonary PRM in a group of healthy adults. 15 healthy volunteers underwent spirometrically monitored chest CT at total lung capacity (TLC) and functional residual capacity (FRC). The paired CT scans were analyzed by PRM for voxel-by-voxel characterization of lung parenchyma according to 4 densitometric classifications: normal lung (TLC ≥ -950 HU, FRC ≥ -856 HU); expiratory low attenuation area (LAA) (TLC ≥ -950 HU, FRC < -856 HU); dual LAA (TLC<-950 HU, FRC < -856 HU); uncharacterized (TLC < -950 HU, FRC ≥ -856 HU). PRM spectrum was 78 % ± 10 % normal lung, 20 % ± 8 % expiratory LAA, and 1 % ± 1 % dual LAA. PRM was similar between genders, there was moderate correlation between dual LAA and spirometrically assessed TLC (R = 0.531; p = 0.042), and between expiratory LAA and Vol Exp/Insp ratio (R = -0.572; p = 0.026). PRM reflects the predominance of normal lung parenchyma in a group of healthy volunteers. However, PRM also confirms the presence of physiological expiratory LAA seemingly related to air trapping and a minimal amount of dual LAA likely reflecting emphysema. (orig.)

  9. Systems for harvesting and handling cotton plant residue

    Energy Technology Data Exchange (ETDEWEB)

    Coates, W. [Univ. of Arizona, Tucson, AZ (United States)

    1993-12-31

    In the warmer regions of the United States, cotton plant residue must be buried to prevent it from serving as an overwintering site for insect pests such as the pink bollworm. Most of the field operations used to bury the residue are high energy consumers and tend to degrade soil structure, thereby increasing the potential for erosion. The residue is of little value as a soil amendment and consequently is considered a negative value biomass. A commercial system to harvest cotton plant residue would be of both economic and environmental benefit to cotton producers. Research has been underway at the University of Arizona since the spring of 1991 to develop a commercially viable system for harvesting cotton plant residue. Equipment durability, degree of densification, energy required, cleanliness of the harvested material, and ease of product handling and transport are some of the performance variables which have been measured. Two systems have proven superior. In both, the plants are pulled from the ground using an implement developed specifically for the purpose. In one system, the stalks are baled using a large round baler, while in the other the stalks are chopped with a forage harvester, and then made into packages using a cotton module maker. Field capacities, energy requirements, package density and durability, and ease of handling with commercially available equipment have been measured for both systems. Selection of an optimum system for a specific operation depends upon end use of the product, and upon equipment availability.

  10. 1990s: High Capacity Backbones

    Indian Academy of Sciences (India)

    First page Back Continue Last page Overview Graphics. 1990s: High Capacity Backbones. Backbone capacities increased from 2.5 Gb/s to 100s of Gb/s during the 1990's. Wavelength division multiplexing with 160 waves of 10 Gb/s was commercially available. Several high-capacity backbones built in the US and Europe.

  11. Landfill Construction and Capacity Expansion

    NARCIS (Netherlands)

    Andre, F.J.; Cerda, E.

    2003-01-01

    We study the optimal capacity and lifetime of landfills taking into account their sequential nature.Such an optimal capacity is characterized by the so-called Optimal Capacity Condition.Particular versions of this condition are obtained for two alternative settings: first, if all the landfills are

  12. Development of Fracture Energy of FRC Materials. Freeze-Thaw Resistance of FRC Materials

    DEFF Research Database (Denmark)

    Stoklund Larsen, E.

    in this SBI Bulletin in order to give more direct information about two of the most important aspects in connection with FRCs. The SBI Bulletin contains two oral presentations given at the Fourth RILEM International Symposium on Fibre Reinforced Cement and Concrete which was held at the University...

  13. Evaluation of residue-residue contact prediction in CASP10

    KAUST Repository

    Monastyrskyy, Bohdan

    2013-08-31

    We present the results of the assessment of the intramolecular residue-residue contact predictions from 26 prediction groups participating in the 10th round of the CASP experiment. The most recently developed direct coupling analysis methods did not take part in the experiment likely because they require a very deep sequence alignment not available for any of the 114 CASP10 targets. The performance of contact prediction methods was evaluated with the measures used in previous CASPs (i.e., prediction accuracy and the difference between the distribution of the predicted contacts and that of all pairs of residues in the target protein), as well as new measures, such as the Matthews correlation coefficient, the area under the precision-recall curve and the ranks of the first correctly and incorrectly predicted contact. We also evaluated the ability to detect interdomain contacts and tested whether the difficulty of predicting contacts depends upon the protein length and the depth of the family sequence alignment. The analyses were carried out on the target domains for which structural homologs did not exist or were difficult to identify. The evaluation was performed for all types of contacts (short, medium, and long-range), with emphasis placed on long-range contacts, i.e. those involving residues separated by at least 24 residues along the sequence. The assessment suggests that the best CASP10 contact prediction methods perform at approximately the same level, and comparably to those participating in CASP9.

  14. Capacity Ten-Seven

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2006-05-04

    The study was initiated to assemble UK solar experts who would define the parameters for the design of solar cell process plant with a capacity of about 10MWp per annum and establish the optimum substrate size, cell configuration and junction structure and show that these characteristics are suited to high volume low cost production. The study focused on proven materials and techniques rather than on innovative materials and processes. Peak production should deliver panels at a cost of less than $1 per peak watt. The study was reported under the headings of fundamental studies, front contact deposition, semiconductor deposition, rear contact deposition, cell isolation and initial design study. Since much of the work is commercially sensitive, not all findings are divulged in the report. The work, which achieved all its targets, was carried out by ICP Solar Technologies UK Ltd under contract to the DTI.

  15. North American fertilizer capacity data

    Energy Technology Data Exchange (ETDEWEB)

    1991-01-01

    This listing of producers and their fertilizer production capacities was compiled in January 1991 with the cooperation of the US and Canadian fertilizer industry. Capacity is only an indicator of supply. Nameplate capacity differs from planned production levels or actual production because plants often operate above or below design capacity. Unless reported otherwise, plant capacities are based on 340 days per year of operation. No adjustment is made for partial year operation. Numerical data for the production of ammonia, ammonium nitrate, nitrogen solutions, urea, phosphate rock, phosphoric acid and ammonium phosphates is included.

  16. Serum trypsin inhibitory capacity in hemodialysis patients

    International Nuclear Information System (INIS)

    Hashemi, Mohammad; Mehrabifar, Hamid; Homayooni, Fatemeh; Naderi, Mohammad; Montazerifar, Farzaneh; Ghavami, Saeid

    2009-01-01

    It has been established that overproduction of reactive oxygen species (ROS) occurs during hemodialysis causing oxidation of proteins. Alpha-1-antitrypsin is the major circulating anti-protease which contains methionine in the active site. The aim of the present study was to measure the level of serum trypsin inhibitory capacity (sTIC) in hemodialysis patients. This case-control study was performed in 52 hemodialysis patients and 49 healthy controls. sTIC was measured by enzymatic assay. The sTIC was significantly (P< 0.001) lower in hemodialysis patients (1.87 + - 0.67 micron mol/min/mL) than healthy controls (2.83 + - 0.44 micron mol/min/L). Reduction of sTIC may be due to the oxidation of methionine residue in the reactive site of alpha-1 antitrypsin. (author)

  17. Radio-capacity of ecosystems

    International Nuclear Information System (INIS)

    Kultakhmedov, Yu.; Kultakhmedova-Vyshnyakova, V.

    1997-01-01

    This paper consider a universal approach to ecosystems of different types, based on representation of their radio-capacity. The concept of ecosystem includes reproduction of components (bio-productivity) and conditions such as maintaining of environment quality. Radio-capacity in the case of radionuclide pollution appears in accumulation and redistribution of radionuclides in the ecosystem. As a result the radionuclides are redistributed and buried in soil or lake bottom sediments. Estimation models for the radio-capacity of water and terrestrial ecosystems are represented. The calculations of the radio-capacity factor of water ecosystems are performed, and the high radio-capacity of a freshwater reservoir (F=0.6-0.8) and extremely high radio-capacity of a reservoir cascade (F c =0.99) is shown material from the Dnieper's cascade reservoirs. The methods of radio-capacity estimation of agroecosystems, wood and marine ecosystems are developed. (authors)

  18. Residual stresses around Vickers indents

    International Nuclear Information System (INIS)

    Pajares, A.; Guiberteau, F.; Steinbrech, R.W.

    1995-01-01

    The residual stresses generated by Vickers indentation in brittle materials and their changes due to annealing and surface removal were studied in 4 mol% yttria partially stabilized zirconia (4Y-PSZ). Three experimental methods to gain information about the residual stress field were applied: (i) crack profile measurements based on serial sectioning, (ii) controlled crack propagation in post indentation bending tests and (iii) double indentation tests with smaller secondary indents located around a larger primary impression. Three zones of different residual stress behavior are deduced from the experiments. Beneath the impression a crack free spherical zone of high hydrostatic stresses exists. This core zone is followed by a transition regime where indentation cracks develop but still experience hydrostatic stresses. Finally, in an outward third zone, the crack contour is entirely governed by the tensile residual stress intensity (elastically deformed region). Annealing and surface removal reduce this crack driving stress intensity. The specific changes of the residual stresses due to the post indentation treatments are described and discussed in detail for the three zones

  19. Actinide recovery from pyrochemical residues

    International Nuclear Information System (INIS)

    Avens, L.R.; Clifton, D.G.; Vigil, A.R.

    1984-01-01

    A new process for recovery of plutonium and americium from pyrochemical waste has been demonstrated. It is based on chloride solution anion exchange at low acidity, which eliminates corrosive HCl fumes. Developmental experiments of the process flowsheet concentrated on molten salt extraction (MSE) residues and gave >95% plutonium and >90% americium recovery. The recovered plutonium contained 6 = from high chloride-low acid solution. Americium and other metals are washed from the ion exchange column with 1N HNO 3 -4.8M NaCl. The plutonium is recovered, after elution, via hydroxide precipitation, while the americium is recovered via NaHCO 3 precipitation. All filtrates from the process are discardable as low-level contaminated waste. Production-scale experiments are now in progress for MSE residues. Flow sheets for actinide recovery from electrorefining and direct oxide reduction residues are presented and discussed

  20. Actinide recovery from pyrochemical residues

    International Nuclear Information System (INIS)

    Avens, L.R.; Clifton, D.G.; Vigil, A.R.

    1985-05-01

    We demonstrated a new process for recovering plutonium and americium from pyrochemical waste. The method is based on chloride solution anion exchange at low acidity, or acidity that eliminates corrosive HCl fumes. Developmental experiments of the process flow chart concentrated on molten salt extraction (MSE) residues and gave >95% plutonium and >90% americium recovery. The recovered plutonium contained 6 2- from high-chloride low-acid solution. Americium and other metals are washed from the ion exchange column with lN HNO 3 -4.8M NaCl. After elution, plutonium is recovered by hydroxide precipitation, and americium is recovered by NaHCO 3 precipitation. All filtrates from the process can be discardable as low-level contaminated waste. Production-scale experiments are in progress for MSE residues. Flow charts for actinide recovery from electro-refining and direct oxide reduction residues are presented and discussed

  1. Alternatives to crop residues for soil amendment

    OpenAIRE

    Powell, J.M.; Unger, P.W.

    1997-01-01

    Metadata only record In semiarid agroecosystems, crop residues can provide important benefits of soil and water conservation, nutrient cycling, and improved subsequent crop yields. However, there are frequently multiple competing uses for residues, including animal forage, fuel, and construction material. This chapter discusses the various uses of crop residues and examines alternative soil amendments when crop residues cannot be left on the soil.

  2. Leaching From Biomass Gasification Residues

    DEFF Research Database (Denmark)

    Allegrini, Elisa; Boldrin, Alessio; Polletini, A.

    2011-01-01

    The aim of the present work is to attain an overall characterization of solid residues from biomass gasification. Besides the determination of chemical and physical properties, the work was focused on the study of leaching behaviour. Compliance and pH-dependence leaching tests coupled with geoche......The aim of the present work is to attain an overall characterization of solid residues from biomass gasification. Besides the determination of chemical and physical properties, the work was focused on the study of leaching behaviour. Compliance and pH-dependence leaching tests coupled...

  3. Carbaryl residues in maize products

    International Nuclear Information System (INIS)

    Zayed, S.M.A.D.; Mansour, S.A.; Mostafa, I.Y.; Hassan, A.

    1976-01-01

    The 14 C-labelled insecticide carbaryl was synthesized from [1- 14 C]-1-naphthol at a specific activity of 3.18mCig -1 . Maize plants were treated with the labelled insecticide under simulated conditions of agricultural practice. Mature plants were harvested and studied for distribution of total residues in untreated grains as popularly roasted and consumed, and in the corn oil and corn germ products. Total residues found under these conditions in the respective products were 0.2, 0.1, 0.45 and 0.16ppm. (author)

  4. Combinatorial construction of toric residues

    OpenAIRE

    Khetan, Amit; Soprounov, Ivan

    2004-01-01

    The toric residue is a map depending on n+1 semi-ample divisors on a complete toric variety of dimension n. It appears in a variety of contexts such as sparse polynomial systems, mirror symmetry, and GKZ hypergeometric functions. In this paper we investigate the problem of finding an explicit element whose toric residue is equal to one. Such an element is shown to exist if and only if the associated polytopes are essential. We reduce the problem to finding a collection of partitions of the la...

  5. Physicochemical and functional characteristics of residual pulp of potato

    Directory of Open Access Journals (Sweden)

    Webber Tavares de CARVALHO

    Full Text Available Abstract Starch-rich liquid effluent is generated after peeling, cutting and washing of tubers during the fries processing. After sedimentation of this effluent is recovered a wet residual pulp, and after drying is obtained dry residual pulp or simply named in this study residual pulp of potato (RPP. In order to convert the effluent into a material easy to store for long periods (such as the potato starch, which would make it suitable for various applications. The aim of this study was to evaluate the effect of the drying conditions, specifically variables temperature and air flow on the drying time and water activity, pH, titratable acidity, instrumental colour parameters, water absorption index, water solubility index and oil absorption capacity of dry RPP. Central Composite Design was used, with temperature levels from 50.0 to 70.0 °C and air flow from 0.06 to 0.092 m3 m–2 s–1. Temperature and airflow affected the study characteristics, except for lightness (L*, water solubility index and oil absorption capacity. It was concluded that milder conditions (lower temperatures and intermediate air flow resulted in higher-quality final products (lighter, less acidic, although requiring higher drying time. Therefore, depending on the product application, different drying conditions can be used.

  6. Physicochemical and functional properties of dietary fiber from maca (Lepidium meyenii Walp.) liquor residue.

    Science.gov (United States)

    Chen, Jinjin; Zhao, Qingsheng; Wang, Liwei; Zha, Shenghua; Zhang, Lijun; Zhao, Bing

    2015-11-05

    Using maca (Lepidium meyenii) liquor residue as the raw material, dietary fiber (DF) was prepared by chemical (MCDF) and enzymatic (MEDF) methods, respectively, of which the physicochemical and functional properties were comparatively studied. High contents of DF were found in MCDF (55.63%) and MEDF (81.10%). Both fibers showed good functional properties, including swelling capacity, water holding capacity, oil holding capacity, glucose adsorption capacity and glucose retardation index. MEDF showed better functional properties, which could be attributed to its higher content of DF, more irregular surface and more abundant monosaccharide composition. The results herein suggest that maca DF prepared by enzymatic method from liquor residue is a good functional ingredient in food products. Copyright © 2015 Elsevier Ltd. All rights reserved.

  7. Weld Residual Stress in Corner Boxing Joints

    OpenAIRE

    Kazuyoshi, Matsuoka; Tokuharu, Yoshii; Ship Research Institute, Ministry of Transport; Ship Research Institute, Ministry of Transport

    1998-01-01

    Fatigue damage often occurs in corner boxing welded joints because of stress concentration and residual stress. The hot spot stress approach is applicable to stress concentration. However, the number of suitable methods for estimating residual stress in welded joints is limited. The purpose of this paper is to clarify the residual stress in corner boxing joints. The method of estimating residual stresses based on the inherent stress technique is presented. Residual stress measurements are per...

  8. Available transmission capacity assessment

    Directory of Open Access Journals (Sweden)

    Škokljev Ivan

    2012-01-01

    Full Text Available Effective power system operation requires the analysis of vast amounts of information. Power market activities expose power transmission networks to high-level power transactions that threaten normal, secure operation of the power system. When there are service requests for a specific sink/source pair in a transmission system, the transmission system operator (TSO must allocate the available transfer capacity (ATC. It is common that ATC has a single numerical value. Additionally, the ATC must be calculated for the base case configuration of the system, while generation dispatch and topology remain unchanged during the calculation. Posting ATC on the internet should benefit prospective users by aiding them in formulating their requests. However, a single numerical value of ATC offers little for prospect for analysis, planning, what-if combinations, etc. A symbolic approach to the power flow problem (DC power flow and ATC offers a numerical computation at the very end, whilst the calculation beforehand is performed by using symbols for the general topology of the electrical network. Qualitative analysis of the ATC using only qualitative values, such as increase, decrease or no change, offers some new insights into ATC evaluation, multiple transactions evaluation, value of counter-flows and their impact etc. Symbolic analysis in this paper is performed after the execution of the linear, symbolic DC power flow. As control variables, the mathematical model comprises linear security constraints, ATC, PTDFs and transactions. The aim is to perform an ATC sensitivity study on a five nodes/seven lines transmission network, used for zonal market activities tests. A relatively complicated environment with twenty possible bilateral transactions is observed.

  9. Solidification process for sludge residue

    International Nuclear Information System (INIS)

    Pearce, K.L.

    1998-01-01

    This report investigates the solidification process used at 100-N Basin to solidify the N Basin sediment and assesses the N Basin process for application to the K Basin sludge residue material. This report also includes a discussion of a solidification process for stabilizing filters. The solidified matrix must be compatible with the Environmental Remediation Disposal Facility acceptance criteria

  10. Machine Arithmetic in Residual Classes,

    Science.gov (United States)

    1981-04-03

    rsmainder/residue, as this ascape /-nsues from thp determination of system. It can be. zaalizpd ;n the presence of th- arithmetic urit, which wor~s in thz sys...modules Nj. Page 417. Proof. Proof ascaps /ensues directly from the theorem of Gauss. Actually/really, since according to condition (py, qj)-=-. then

  11. Residual stress in polyethylene pipes

    Czech Academy of Sciences Publication Activity Database

    Poduška, Jan; Hutař, Pavel; Kučera, J.; Frank, A.; Sadílek, J.; Pinter, G.; Náhlík, Luboš

    2016-01-01

    Roč. 54, SEP (2016), s. 288-295 ISSN 0142-9418 R&D Projects: GA MŠk LM2015069; GA MŠk(CZ) LQ1601 Institutional support: RVO:68081723 Keywords : polyethylene pipe * residual stress * ring slitting method * lifetime estimation Subject RIV: JL - Materials Fatigue, Friction Mechanics Impact factor: 2.464, year: 2016

  12. Managing woodwaste: Yield from residue

    Energy Technology Data Exchange (ETDEWEB)

    Nielson, E. [LNS Services, Inc., North Vancouver, British Columbia (Canada); Rayner, S. [Pacific Waste Energy Inc., Burnaby, British Columbia (Canada)

    1993-12-31

    Historically, the majority of sawmill waste has been burned or buried for the sole purpose of disposal. In most jurisdictions, environmental legislation will prohibit, or render uneconomic, these practices. Many reports have been prepared to describe the forest industry`s residue and its environmental effect; although these help those looking for industry-wide or regional solutions, such as electricity generation, they have limited value for the mill manager, who has the on-hands responsibility for generation and disposal of the waste. If the mill manager can evaluate waste streams and break them down into their usable components, he can find niche market solutions for portions of the plant residue and redirect waste to poor/no-return, rather than disposal-cost, end uses. In the modern mill, residue is collected at the individual machine centre by waste conveyors that combine and mix sawdust, shavings, bark, etc. and send the result to the hog-fuel pile. The mill waste system should be analyzed to determine the measures that can improve the quality of residues and determine the volumes of any particular category before the mixing, mentioned above, occurs. After this analysis, the mill may find a niche market for a portion of its woodwaste.

  13. Leptogenesis and residual CP symmetry

    International Nuclear Information System (INIS)

    Chen, Peng; Ding, Gui-Jun; King, Stephen F.

    2016-01-01

    We discuss flavour dependent leptogenesis in the framework of lepton flavour models based on discrete flavour and CP symmetries applied to the type-I seesaw model. Working in the flavour basis, we analyse the case of two general residual CP symmetries in the neutrino sector, which corresponds to all possible semi-direct models based on a preserved Z 2 in the neutrino sector, together with a CP symmetry, which constrains the PMNS matrix up to a single free parameter which may be fixed by the reactor angle. We systematically study and classify this case for all possible residual CP symmetries, and show that the R-matrix is tightly constrained up to a single free parameter, with only certain forms being consistent with successful leptogenesis, leading to possible connections between leptogenesis and PMNS parameters. The formalism is completely general in the sense that the two residual CP symmetries could result from any high energy discrete flavour theory which respects any CP symmetry. As a simple example, we apply the formalism to a high energy S 4 flavour symmetry with a generalized CP symmetry, broken to two residual CP symmetries in the neutrino sector, recovering familiar results for PMNS predictions, together with new results for flavour dependent leptogenesis.

  14. Solow Residuals Without Capital Stocks

    DEFF Research Database (Denmark)

    Burda, Michael C.; Severgnini, Battista

    2014-01-01

    We use synthetic data generated by a prototypical stochastic growth model to assess the accuracy of the Solow residual (Solow, 1957) as a measure of total factor productivity (TFP) growth when the capital stock in use is measured with error. We propose two alternative measurements based on current...

  15. Algorithmic complexity of quantum capacity

    Science.gov (United States)

    Oskouei, Samad Khabbazi; Mancini, Stefano

    2018-04-01

    We analyze the notion of quantum capacity from the perspective of algorithmic (descriptive) complexity. To this end, we resort to the concept of semi-computability in order to describe quantum states and quantum channel maps. We introduce algorithmic entropies (like algorithmic quantum coherent information) and derive relevant properties for them. Then we show that quantum capacity based on semi-computable concept equals the entropy rate of algorithmic coherent information, which in turn equals the standard quantum capacity. Thanks to this, we finally prove that the quantum capacity, for a given semi-computable channel, is limit computable.

  16. Capacity Measurement with the UIC 406 Capacity Method

    DEFF Research Database (Denmark)

    Landex, Alex; Schittenhelm, Bernd; Kaas, Anders H.

    2008-01-01

    This article describes the fast and effective UIC 406 method for calculating capacity consumption on railway lines. It is possible to expound the UIC 406 method in different ways which can lead to different capacity consumptions. Therefore, this article describes how the methodology is expounded...

  17. Influence of organic waste and residue mud additions on chemical, physical and microbial properties of bauxite residue sand.

    Science.gov (United States)

    Jones, Benjamin E H; Haynes, Richard J; Phillips, Ian R

    2011-02-01

    In an alumina refinery, bauxite ore is treated with sodium hydroxide at high temperatures and pressures and for every tone of alumina produced, about 2 tones of alkaline, saline bauxite processing waste is also produced. At Alcoa, a dry stacking system of disposal is used, and it is the sand fraction of the processing waste that is rehabilitated. There is little information available regarding the most appropriate amendments to add to the processing sand to aid in revegetation. The purpose of this study was to investigate how the addition of organic wastes (biosolids and poultry manure), in the presence or absence of added residue mud, would affect the properties of the residue sand and its suitability for revegetation. Samples of freshly deposited residue sand were collected from Alcoa's Kwinana refinery. Samples were treated with phosphogypsum (2% v/v), incubated, and leached. A laboratory experiment was then set up in which the two organic wastes were applied at 0 or the equivalent to 60 tones ha(-1) in combination with residue mud added at rates of 0%, 10% and 20% v/v. Samples were incubated for 8 weeks, after which, key chemical, physical and microbial properties of the residue sand were measured along with seed germination. Additions of residue mud increased exchangeable Na(+), ESP and the pH, and HCO (3) (-) and Na(+) concentrations in saturation paste extracts. Additions of biosolids and poultry manure increased concentrations of extractable P, NH (4) (+) , K, Mg, Cu, Zn, Mn and Fe. Addition of residue mud, in combination with organic wastes, caused a marked decrease in macroporosity and a concomitant increase in mesoporosity, available water holding capacity and the quantity of water held at field capacity. With increasing residue mud additions, the percentage of sample present as sand particles (2 mm diameter) increased; greatest aggregation occurred where a combination of residue mud and poultry manure were added. Stability of aggregates, as measured by

  18. The effect of surgery on lung volume and conventional monitoring parameters in ventilated newborn infants.

    Science.gov (United States)

    Proquitté, H; Freiberger, O; Yilmaz, S; Bamberg, C; Degenhardt, P; Roehr, C C; Wauer, R R; Schmalisch, G

    2010-05-01

    In newborn infants, thoraco-abdominal surgery is a serious intervention with respect to gas exchange and lung mechanics. This prospective clinical study compared surgery-induced changes in functional residual capacity (FRC) and ventilation inhomogeneity (VI) indices with changes in conventional monitoring parameters. Of 29 ventilated newborns (mean weight 2,770+/-864 g at surgery), 13, nine and seven underwent thoracic, abdominal or congenital diaphragmatic hernia (CDH) surgery, respectively. The multiple breath washout (MBWO) technique using heptafluoropropane as tracer gas (Babylog 8000; Dräger, Lübeck, Germany) was performed ventilatory monitoring parameters. FRC decreased in non-CDH infants, while FRC increased and VI indices decreased in CDH infants. Despite improvements, the differences in FRC and VI between CDH and non-CDH infants indicated persistent impaired lung function in CHD infants. MBWO can be advantageously used to measure the effect of surgery on the lung. While FRC and VI indices changed following surgery, conventional monitoring parameters did not.

  19. Positive end-expiratory pressure optimization using electric impedance tomography in morbidly obese patients during laparoscopic gastric bypass surgery.

    Science.gov (United States)

    Erlandsson, K; Odenstedt, H; Lundin, S; Stenqvist, O

    2006-08-01

    Morbidly obese patients have an increased risk for peri-operative lung complications and develop a decrease in functional residual capacity (FRC). Electric impedance tomography (EIT) can be used for continuous, fast-response measurement of lung volume changes. This method was used to optimize positive end-expiratory pressure (PEEP) to maintain FRC. Fifteen patients with a body mass index of 49 +/- 8 kg/m(2) were studied during anaesthesia for laparoscopic gastric bypass surgery. Before induction, 16 electrodes were placed around the thorax to monitor ventilation-induced impedance changes. Calibration of the electric impedance tomograph against lung volume changes was made by increasing the tidal volume in steps of 200 ml. PEEP was titrated stepwise to maintain a horizontal baseline of the EIT curve, corresponding to a stable FRC. Absolute FRC was measured with a nitrogen wash-out/wash-in technique. Cardiac output was measured with an oesophageal Doppler method. Volume expanders, 1 +/- 0.5 l, were given to prevent PEEP-induced haemodynamic impairment. Impedance changes closely followed tidal volume changes (R(2) > 0.95). The optimal PEEP level was 15 +/- 1 cmH(2)O, and FRC at this PEEP level was 1706 +/- 447 ml before and 2210 +/- 540 ml after surgery (P depression in spite of a high PEEP level.

  20. European experience in transport/storage cask for vitrified residues

    International Nuclear Information System (INIS)

    Otton, Camille; Sicard, Damien

    2007-01-01

    Available in abstract form only. Full text of publication follows: Because of the evolution of burnup of spent fuel to be reprocessed, the high activity vitrified residues would not be transported in the existing cask designs. Therefore, TN International has decided in the late nineties to develop a brand new design of casks with optimized capacity able to store and transport the most active and hottest canisters: the TN TM 81 casks currently in use in Switzerland and the TN TM 85 cask which shall permit in the near future in Germany the storage and the transport of the most active vitrified residues defining a thermal power of 56 kW (kilowatts). The challenges for the TN TM 81 and TN TM 85 cask designs were that the geometry entry data were very restrictive and were combined with a fairly wide range set by the AREVA NC Specification relative to vitrified residue canister. The TN TM 81 and the TN TM 85 casks have been designed to fully anticipate shipment constraints of the present vitrified residue production. It also used the feedback of current shipments and the operational constraints and experience of receiving and shipping facilities. The casks had to fit as much as possible in the existing procedures for the already existing flasks such as the TN TM 28 cask and TS 28 V cask, all along the logistics chain of loading, unloading, transport and maintenance. (authors)

  1. Radioactive material in residues of health services residues

    International Nuclear Information System (INIS)

    Costa R, A. Jr.; Recio, J.C.

    2006-01-01

    The work presents the operational actions developed by the one organ responsible regulator for the control of the material use radioactive in Brazil. Starting from the appearance of coming radioactive material of hospitals and clinical with services of nuclear medicine, material that that is picked up and transported in specific trucks for the gathering of residuals of hospital origin, and guided one it manufactures of treatment of residuals of services of health, where they suffer radiological monitoring before to guide them for final deposition in sanitary embankment, in the city of Sao Paulo, Brazil. The appearance of this radioactive material exposes a possible one violation of the norms that govern the procedures and practices in that sector in the country. (Author)

  2. RECOVERY OF WHEAT RESIDUE NITROGEN 15 AND RESIDUAL ...

    African Journals Online (AJOL)

    Therefore 85 kg ha-1 N as labelled ammonium sulfate (9.764% atomic excess) was applied in a three-split application. Fertiliser N recovery by wheat in the first year was 33.1%. At harvest, 64.8% of fertiliser N was found in the 0 - 80 cm profile as residual fertiliser-derived N; 2.1% of the applied N could not be accounted for ...

  3. Agrochemical residue-biota interactions in soil and aquatic ecosystems

    International Nuclear Information System (INIS)

    1980-01-01

    Two FAO/IAEA coordinated research programmes are concerned with isotopic tracer-aided studies of agrochemical residue-biota interactions in soils and aquatic ecosystems. They currently involve 18 studies in 14 countries: Brazil, Canada, Egypt, F.R. Germany, Hungary, India, Indonesia, Iraq, Israel, Malaysia, Thailand, Turkey, USA and USSR. The aim was to develop, standardize and apply labelled substrate techniques for comparative assays of primary autotrophic and microheterotrophic production and decay, and complementary tracer techniques to determine the fate, persistence and bioconcentration of trace contaminants. Comparable data were studied concerning the current status of water bodies and likely changes due to contaminants. Soil capacity to decompose undesirable contaminants and residues, and to promote desirable transformations were studied. The techniques were also applied as a diagnostic and prognostic tool, with priority given to rice ecosystems

  4. Installed capacity in New York

    International Nuclear Information System (INIS)

    Charlton, J.

    2006-01-01

    This presentation discussed capacity issues related to the New York Independent System Operator (NYISO). The NYISO's market volume was approximately $11 billion in 2005, and it was responsible for providing 32,075 MW of electricity at peak load to its users. Regulatory uncertainty is currently discouraging investment in new generating resources. All load serving entities are required to contract for sufficient capacity in order to meet their capacity obligations. Market participants currently determine capacity and energy revenues. The NYISO market allows suppliers to recover variable costs for providing ancillary services, and the economic value of the revenue source governs decisions made in the wholesale electricity market. The installed capacity market was designed as a spot auction deficiency auction. Phased-in demand curves are used to modify the installed capacity market's design. A sloped demand curve mechanism is used to value capacity above the minimum requirement for both reliability and competition. Participation in the day-ahead market enhances competition and exerts downward pressure on energy and ancillary service market prices. It was concluded that the market structures and design features of the installed capacity markets recognize the need for system reliability in addition to encouraging robust competition and recognizing energy price caps and regulatory oversights. tabs., figs

  5. Checking Capacity for MIMO Configurations

    DEFF Research Database (Denmark)

    Thaysen, Jesper; Jakobsen, Kaj Bjarne

    2007-01-01

    Wireless system capacity can be added by increasing the number of antennas in a MIMO setup or by carefully optimizing the performance of a smaller number of antennas.......Wireless system capacity can be added by increasing the number of antennas in a MIMO setup or by carefully optimizing the performance of a smaller number of antennas....

  6. Estimation of capacities on Florida freeways.

    Science.gov (United States)

    2014-09-01

    Current capacity estimates within Floridas travel time reliability tools rely on the Highway Capacity Manual (HCM 2010) to : estimate capacity under various conditions. Field measurements show that the capacities of Florida freeways are noticeably...

  7. North American fertilizer capacity data

    Energy Technology Data Exchange (ETDEWEB)

    1993-02-01

    This listing of fertilizer producers and their production capacities was compiled in February 1993 with the cooperation of the US and Canadian fertilizer industry. TVA does not guarantee the completeness or accuracy of the information. Capacity is only an indicator of supply. Nameplate capacity differs from planned production levels or actual production because plants often operate above or below design capacity. Unless reported otherwise, plant capacities are based on 340 days per year of operation. No adjustment is made for partial year operation. Information is given on the following types of fertilizers: ammonia, ammonium nitrate, nitrogen solutions, urea, ammonium sulfate, phosphate rock, wet-process phosphoric acid, ammonium phosphates, concentrated superphosphates, potash, nitric acid, superphosphoric acid, upgraded phosphoric acids, normal superphosphate, elemental phosphorus, potassium sulfate, and sulfate of potash/magnesia.

  8. Capacity Building in Land Administration

    DEFF Research Database (Denmark)

    Enemark, Stig; Williamson, I

    2004-01-01

    Capacity building increasingly seen as a key component of land administration projects in developing and countries in transition undertaken by the international development banks and individual country development assistance agencies. However, the capacity building concept is often used within...... infrastructures for implementing land policies in a sustainable way. Where a project is established to create land administration infrastructures in developing or transition countries, it is critical that capacity building is a mainstream component, not as an add-on, which is often the case. In fact such projects...... should be dealt with as capacity building projects in themselves.    The article introduces a conceptual analytical framework that provides some guidance when dealing with capacity building for land administration in support of a broader land policy agenda....

  9. Residual energy applications program systems analysis report

    Energy Technology Data Exchange (ETDEWEB)

    Yngve, P.W.

    1980-10-01

    Current DOE plans call for building an Energy Applied Systems Test (EAST) Facility at the Savannah River Plant in close proximity to the 140 to 150/sup 0/F waste heat from one of several operating nuclear reactors. The waste water flow from each reactor, approximately 165,000 gpm, provides a unique opportunity to test the performance and operating characteristics of large-scale waste heat power generation and heat pump system concepts. This report provides a preliminary description of the potential end-use market, parametric data on heat pump and the power generation system technology, a preliminary listing of EAST Facility requirements, and an example of an integrated industrial park utilizing the technology to maximize economic pay back. The parametric heat pump analysis concluded that dual-fluid Rankine cycle heat pumps with capacities as high as 400 x 10/sup 6/ Btu/h, can utilize large sources of low temperature residual heat to provide 300/sup 0/F saturatd steam for an industrial park. The before tax return on investment for this concept is 36.2%. The analysis also concluded that smaller modular heat pumps could fulfill the same objective while sacrificing only a moderate rate of return. The parametric power generation analysis concluded that multi-pressure Rankine cycle systems not only are superior to single pressure systems, but can also be developed for large systems (approx. = 17 MW/sub e/). This same technology is applicable to smaller systems at the sacrifice of higher investment per unit output.

  10. The Cauchy method of residues

    CERN Document Server

    Mitrinović, Dragoslav S

    1993-01-01

    Volume 1, i. e. the monograph The Cauchy Method of Residues - Theory and Applications published by D. Reidel Publishing Company in 1984 is the only book that covers all known applications of the calculus of residues. They range from the theory of equations, theory of numbers, matrix analysis, evaluation of real definite integrals, summation of finite and infinite series, expansions of functions into infinite series and products, ordinary and partial differential equations, mathematical and theoretical physics, to the calculus of finite differences and difference equations. The appearance of Volume 1 was acknowledged by the mathematical community. Favourable reviews and many private communications encouraged the authors to continue their work, the result being the present book, Volume 2, a sequel to Volume 1. We mention that Volume 1 is a revised, extended and updated translation of the book Cauchyjev raeun ostataka sa primenama published in Serbian by Nau~na knjiga, Belgrade in 1978, whereas the greater part ...

  11. Calcination/dissolution residue treatment

    International Nuclear Information System (INIS)

    Knight, R.C.; Creed, R.F.; Patello, G.K.; Hollenberg, G.W.; Buehler, M.F.; O'Rourke, S.M.; Visnapuu, A.; McLaughlin, D.F.

    1994-09-01

    Currently, high-level wastes are stored underground in steel-lined tanks at the Hanford site. Current plans call for the chemical pretreatment of these wastes before their immobilization in stable glass waste forms. One candidate pretreatment approach, calcination/dissolution, performs an alkaline fusion of the waste and creates a high-level/low-level partition based on the aqueous solubilities of the components of the product calcine. Literature and laboratory studies were conducted with the goal of finding a residue treatment technology that would decrease the quantity of high-level waste glass required following calcination/dissolution waste processing. Four elements, Fe, Ni, Bi, and U, postulated to be present in the high-level residue fraction were identified as being key to the quantity of high-level glass formed. Laboratory tests of the candidate technologies with simulant high-level residues showed reductive roasting followed by carbonyl volatilization to be successful in removing Fe, Ni, and Bi. Subsequent bench-scale tests on residues from calcination/dissolution processing of genuine Hanford Site tank waste showed Fe was separated with radioelement decontamination factors of 70 to 1,000 times with respect to total alpha activity. Thermodynamic analyses of the calcination of five typical Hanford Site tank waste compositions also were performed. The analyses showed sodium hydroxide to be the sole molten component in the waste calcine and emphasized the requirement for waste blending if fluid calcines are to be achieved. Other calcine phases identified in the thermodynamic analysis indicate the significant thermal reconstitution accomplished in calcination

  12. 78 FR 52958 - Announcement of Test Concerning Manifesting and Entry of Residue Found in Instruments of...

    Science.gov (United States)

    2013-08-27

    ... manifested in this fashion and will not be required under the Residue Test. c. Containers Arriving With Cargo... by weight or volume, using industry standards, must be manifested. A consumption entry will be... container's total capacity by weight or volume, using industry standards, will be considered to contain...

  13. Hepatocytes Contribute to Residual Glucose Production in a Mouse Model for Glycogen Storage Disease Type Ia

    NARCIS (Netherlands)

    Hijmans, Brenda S.; Boss, Andreas; van Dijk, Theo H.; Soty, Maud; Wolters, Henk; Mutel, Elodie; Groen, Albert K.; Derks, Terry G. J.; Mithieux, Gilles; Heerschap, Arend; Reijngoud, Dirk-Jan; Rajas, Fabienne; Oosterveer, Maaike H.

    2017-01-01

    It is a long-standing enigma how glycogen storage disease (GSD) type I patients retain a limited capacity for endogenous glucose production despite the loss of glucose-6-phosphatase activity. Insight into the source of residual endogenous glucose production is of clinical importance given the risk

  14. Residual Strength of Glued-in Bolts After 9 Years In Situ Loading

    DEFF Research Database (Denmark)

    Pedersen, Martin Bo Uhre; Clorius, Christian Odin; Damkilde, Lars

    1996-01-01

    deviation of 37 kN. Comparing this mean residual strength with previously recorded test data reveals a 5% strength reduction. The force displacement curves shows no plastic capacity in the connections. At fracture, a displacement between 0.4 mm and 1.0 mm was observed. In the majority of failures the bolts...

  15. Capacity Measurement with the UIC 406 Capacity Method

    DEFF Research Database (Denmark)

    Landex, Alex; Schittenhelm, Bernd; Kaas, Anders H.

    2008-01-01

    This article describes the fast and effective UIC 406 method for calculating capacity consumption on railway lines. It is possible to expound the UIC 406 method in different ways which can lead to different capacity consumptions. Therefore, this article describes how the methodology is expounded...... in Denmark. This includes how and where to divide the railway lines into line sections, how to analyze stations and junctions, and how to examine line sections with different amounts of tracks....

  16. Characterisation and management of concrete grinding residuals.

    Science.gov (United States)

    Kluge, Matt; Gupta, Nautasha; Watts, Ben; Chadik, Paul A; Ferraro, Christopher; Townsend, Timothy G

    2018-02-01

    Concrete grinding residue is the waste product resulting from the grinding, cutting, and resurfacing of concrete pavement. Potential beneficial applications for concrete grinding residue include use as a soil amendment and as a construction material, including as an additive to Portland cement concrete. Concrete grinding residue exhibits a high pH, and though not hazardous, it is sufficiently elevated that precautions need to be taken around aquatic ecosystems. Best management practices and state regulations focus on reducing the impact on such aquatic environment. Heavy metals are present in concrete grinding residue, but concentrations are of the same magnitude as typically recycled concrete residuals. The chemical composition of concrete grinding residue makes it a useful product for some soil amendment purposes at appropriate land application rates. The presence of unreacted concrete in concrete grinding residue was examined for potential use as partial replacement of cement in new concrete. Testing of Florida concrete grinding residue revealed no dramatic reactivity or improvement in mortar strength.

  17. Polychlorinated Biphenyls (PCB) Residue Effects Database

    Data.gov (United States)

    U.S. Environmental Protection Agency — The PCB Residue Effects (PCBRes) Database was developed to assist scientists and risk assessors in correlating PCB and dioxin-like compound residues with toxic...

  18. Interpretation on Recycling Plastics from Shredder Residue

    Science.gov (United States)

    EPA is considering an interpretation of its regulations that would generally allow for recycling of plastic separated from shredder residue under the conditions described in the Voluntary Procedures for Recycling Plastics from Shredder Residue.

  19. Regular capacities on metrizable spaces

    Directory of Open Access Journals (Sweden)

    T. M. Cherkovskyi

    2014-07-01

    Full Text Available It is proved that for a (not necessarily compact metric space: the metrics on the space of capacities in the sense of Zarichnyi and Prokhorov are equal; completeness of the space of capacities is equivalent to completeness of the original space. It is shown that for the capacities on metrizable spaces the properties of $\\omega$-smoothness and of $\\tau$-smoothness are equivalent precisely on the separable spaces, and the properties of $\\omega$-smoothness and of regularity w.r.t. some (then w.r.t. any admissible metric are equivalent precisely on the compact spaces.

  20. Characterization of biomass residues and their amendment effects on water sorption and nutrient leaching in sandy soil.

    Science.gov (United States)

    Wang, Letian; Tong, Zhaohui; Liu, Guodong; Li, Yuncong

    2014-07-01

    In this study, we evaluated the efficiency of two types of biomass residues (fermentation residues from a bioethanol process, FB; brown mill residues from a papermaking process, BM) as amendments for a sandy soil. The characteristics of these residues including specific surface areas, morphologies and nutrient sorption capacity were measured. The effects of biorefinery residues on water and nutrient retention were investigated in terms of different particle sizes and loadings. The results indicated that bio-based wastes FB and BM were able to significantly improve water and nutrient retention of sandy soil. The residues with larger surface areas had better water and nutrient retention capability. Specifically, in the addition of 10% loading, FB and BM was able to improve water retention by approximately 150% and 300%, while reduce 99% of ammonium and phosphate concentration in the leachate compare to the soil control, respectively. Copyright © 2014 Elsevier Ltd. All rights reserved.

  1. Residues of {sup 14}C-paclobutrazol in mangoes

    Energy Technology Data Exchange (ETDEWEB)

    Costa, Maria A.; Tornisielo, Valdemar L.; Castanho, Giuliane M., E-mail: macosta@cena.usp.b [Centro de Energia Nuclear na Agricultura (CENA/USP), Piracicaba, SP (Brazil). Lab. de Ecotoxicologia

    2009-07-01

    Paclobutrazol (PBZ) is a growth regulator used in agricultural systems whose purpose is the control of vegetative growth, stimulating the reproductive capacity of plants. This growth regulator remains active in soil for a long time and its half-life varies with the type of soil and climatic conditions, can severely affect the development of crops. This work aimed to study the residues / metabolites of {sup 14}C-PBZ in mango pulp Tommy Atkins. The tests were performed with mangoes grown in pots stainless steel and application of {sup 14}C-PBZ was performed by the soil projection of the crown, and the mangoes tested in two periods, one year and two years after application. To evaluate the levels of residues of {sup 14}C-PBZ was realize the burning of 200 mg of pulp on biological oxidized and detached {sup 14}CO{sub 2} was detected by liquid scintillation spectrophotometer. The results were 1.65 % of residue of PBZ on fruit collected after two years of application and 4.30 % of residue of PBZ collected on fruit after a year of application and also can see that the product remained in the soil for more than one year, is translocated to the plant and reach the edible part, the pulp fruit. The identification of residual {sup 14}C- PBZ/metabolites by thin-layer chromatography did not reveal any pattern of PBZ / metabolites due to the low activity detected in the samples. Therefore, another procedure was performed for extraction and then analyzed by high performance liquid chromatography (HPLC) for detection of metabolites in the PBZ of mango pulp. (author)

  2. Investigation of the possibility of using residual heat reactor energy

    Science.gov (United States)

    Aminov, R. Z.; Yurin, V. E.; Bessonov, V. N.

    2017-11-01

    The largest contribution to the probable frequency of core damage is blackout events. The main component of the heat capacity at each reactor within a few minutes following a blackout is the heat resulting from the braking of beta-particles and the transfer of gamma-ray energy by the fission fragments and their decay products, which is known as the residual heat. The power of the residual heat changes gradually over a long period of time and for a VVER-1000 reactor is about 15–20 MW of thermal power over 72 hours. Current cooldown systems increase the cost of the basic nuclear power plants (NPP) funds without changing the amount of electricity generated. Such systems remain on standby, accelerating the aging of the equipment and accordingly reducing its reliability. The probability of system failure increases with the duration of idle time. Furthermore, the reactor residual heat energy is not used. A proposed system for cooling nuclear power plants involves the use of residual thermal power to supply the station’s own needs in emergency situations accompanied by a complete blackout. The thermal power of residual heat can be converted to electrical energy through an additional low power steam turbine. In normal mode, the additional steam turbine generates electricity, which makes it possible to ensure spare NPP and a return on the investment in the reservation system. In this work, experimental data obtained from a Balakovo NPP was analyzed to determine the admissibility of cooldown of the reactors through the 2nd circuit over a long time period, while maintaining high-level parameters for the steam generated by the steam generators.

  3. Residues of 14C-paclobutrazol in mangoes

    International Nuclear Information System (INIS)

    Costa, Maria A.; Tornisielo, Valdemar L.; Castanho, Giuliane M.

    2009-01-01

    Paclobutrazol (PBZ) is a growth regulator used in agricultural systems whose purpose is the control of vegetative growth, stimulating the reproductive capacity of plants. This growth regulator remains active in soil for a long time and its half-life varies with the type of soil and climatic conditions, can severely affect the development of crops. This work aimed to study the residues / metabolites of 14 C-PBZ in mango pulp Tommy Atkins. The tests were performed with mangoes grown in pots stainless steel and application of 14 C-PBZ was performed by the soil projection of the crown, and the mangoes tested in two periods, one year and two years after application. To evaluate the levels of residues of 14 C-PBZ was realize the burning of 200 mg of pulp on biological oxidized and detached 14 CO 2 was detected by liquid scintillation spectrophotometer. The results were 1.65 % of residue of PBZ on fruit collected after two years of application and 4.30 % of residue of PBZ collected on fruit after a year of application and also can see that the product remained in the soil for more than one year, is translocated to the plant and reach the edible part, the pulp fruit. The identification of residual 14 C- PBZ/metabolites by thin-layer chromatography did not reveal any pattern of PBZ / metabolites due to the low activity detected in the samples. Therefore, another procedure was performed for extraction and then analyzed by high performance liquid chromatography (HPLC) for detection of metabolites in the PBZ of mango pulp. (author)

  4. Residual Analysis of Generalized Autoregressive Integrated Moving ...

    African Journals Online (AJOL)

    In this study, analysis of residuals of generalized autoregressive integrated moving average bilinear time series model was considered. The adequacy of this model was based on testing the estimated residuals for whiteness. Jarque-Bera statistic and squared-residual autocorrelations were used to test the estimated ...

  5. 9 CFR 311.39 - Biological residues.

    Science.gov (United States)

    2010-01-01

    ... 9 Animals and Animal Products 2 2010-01-01 2010-01-01 false Biological residues. 311.39 Section... Biological residues. Carcasses, organs, or other parts of carcasses of livestock shall be condemned if it is determined that they are adulterated because of the presence of any biological residues. ...

  6. Cycling of grain legume residue nitrogen

    DEFF Research Database (Denmark)

    Jensen, E.S.

    1995-01-01

    Symbiotic nitrogen fixation by legumes is the main input of nitrogen in ecological agriculture. The cycling of N-15-labelled mature pea (Pisum sativum L.) residues was studied during three years in small field plots and lysimeters. The residual organic labelled N declined rapidly during the initial...... management methods in order to conserve grain legume residue N sources within the soil-plant system....

  7. Neutron residual stress measurements in linepipe

    Science.gov (United States)

    Law, Michael; Gnaëpel-Herold, Thomas; Luzin, Vladimir; Bowie, Graham

    2006-11-01

    Residual stresses in gas pipelines are generated by manufacturing and construction processes and may affect the subsequent pipe integrity. In the present work, the residual stresses in eight samples of linepipe were measured by neutron diffraction. Residual stresses changed with some coating processes. This has special implications in understanding and mitigating stress corrosion cracking, a major safety and economic problem in some gas pipelines.

  8. Neutron residual stress measurements in linepipe

    International Nuclear Information System (INIS)

    Law, Michael; Gnaepel-Herold, Thomas; Luzin, Vladimir; Bowie, Graham

    2006-01-01

    Residual stresses in gas pipelines are generated by manufacturing and construction processes and may affect the subsequent pipe integrity. In the present work, the residual stresses in eight samples of linepipe were measured by neutron diffraction. Residual stresses changed with some coating processes. This has special implications in understanding and mitigating stress corrosion cracking, a major safety and economic problem in some gas pipelines

  9. Glycogen is large molecules wherein Glucose residues

    Indian Academy of Sciences (India)

    First page Back Continue Last page Overview Graphics. Glycogen is large molecules wherein Glucose residues. Glycogen is large molecules wherein Glucose residues. linked by α-(1- 4) glycosidic bonds into chains and chains. branch via α-(1- 6) linkage. Branching points are about every fourth residue – allows. glucose ...

  10. Reconstructing cognition in Korsakoff’s syndrome : Diagnosis, residual capacities, and rehabilitation

    NARCIS (Netherlands)

    Oudman, F.A.

    2016-01-01

    Korsakoff's syndrome (KS) is a preventable neuropsychiatric disorder caused by alcoholism induced vitamine B1 deficiency. In the acute phase of this vitamine B1 deficiency, called Wernicke’s encephalopathy (WE), the neuropsychiatric disorder is fully reversibly by fast intravenous or intramuscular

  11. Capacity Building in Land Management

    DEFF Research Database (Denmark)

    Enemark, Stig; Ahene, Rexford

    2003-01-01

    There is a significant need for capacity building in the interdisciplinary area of land management especially in developing countries and countries in transition, to deal with the complex issues of building efficient land information systems and sustainable institutional infrastructures. Capacity...... development in this area. Furthermore, capacity building should ensure that the focus is on building sound institutions and governance rather than just high-level IT-infrastructures.    This overall approach to capacity building in land management is used for implementing a new land policy reform in Malawi...... building in land management is not only a question of establishing a sufficient technological level or sufficient economic resources. It is mainly a question of understanding the interdisciplinary and cross-sectoral nature of land administration systems, and understanding the need for human resource...

  12. Building Capacity in Ethical Review

    DEFF Research Database (Denmark)

    Douglas-Jones, Rachel

    2017-01-01

    Capacity building in biomedical research ethics review has been a European priority since the early 2000s. Prompted by the increase in data originating in internationally sponsored trials in emerging economies, a range of capacity building initiatives were put in place in the field of ethical...... review to ensure the protection of human subjects participating in research. Drawing on fieldwork with the Forum for Ethical Review Committees in the Asian and Western Pacific Region, I explore two distinct forms taken by capacity building within that organization to support and train members of ethics...... review committees. The first, with an emphasis on standards and measurability, takes as its priority international accountability for clinical trial research. e second explores how the organization goes about persuading trainees to see and do ‘ethics’ differently. is distinction between forms of capacity...

  13. Capacity Markets and Market Stability

    International Nuclear Information System (INIS)

    Stauffer, Hoff

    2006-01-01

    The good news is that market stability can be achieved through a combination of longer-term contracts, auctions for far enough in the future to permit new entry, a capacity management system, and a demand curve. The bad news is that if and when stable capacity markets are designed, the markets may seem to be relatively close to where we started - with integrated resource planning. Market ideologues will find this anathema. (author)

  14. Research projects and capacity building

    CSIR Research Space (South Africa)

    Breen, CM

    2004-10-01

    Full Text Available - knowledged as necessary and urgent, but is this sufficient? Are ?head counts? and/or ?degree counts? of individuals from marginalised sectors, including gender, participating in research projects appro- priate measures for capacity building? Much depends... numbers of people (including race and gender) gaining higher degrees and papers published in peer-reviewed journals may provide some measure of capacity building, they do not measure the extent to which fundamental enabling conditions have been fostered...

  15. Maximizing the optical network capacity.

    Science.gov (United States)

    Bayvel, Polina; Maher, Robert; Xu, Tianhua; Liga, Gabriele; Shevchenko, Nikita A; Lavery, Domaniç; Alvarado, Alex; Killey, Robert I

    2016-03-06

    Most of the digital data transmitted are carried by optical fibres, forming the great part of the national and international communication infrastructure. The information-carrying capacity of these networks has increased vastly over the past decades through the introduction of wavelength division multiplexing, advanced modulation formats, digital signal processing and improved optical fibre and amplifier technology. These developments sparked the communication revolution and the growth of the Internet, and have created an illusion of infinite capacity being available. But as the volume of data continues to increase, is there a limit to the capacity of an optical fibre communication channel? The optical fibre channel is nonlinear, and the intensity-dependent Kerr nonlinearity limit has been suggested as a fundamental limit to optical fibre capacity. Current research is focused on whether this is the case, and on linear and nonlinear techniques, both optical and electronic, to understand, unlock and maximize the capacity of optical communications in the nonlinear regime. This paper describes some of them and discusses future prospects for success in the quest for capacity. © 2016 The Authors.

  16. Natural radioactivity in petroleum residues

    International Nuclear Information System (INIS)

    Gazineu, M.H.P.; Gazineu, M.H.P.; Hazin, C.A.; Hazin, C.A.

    2006-01-01

    The oil extraction and production industry generates several types of solid and liquid wastes. Scales, sludge and water are typical residues that can be found in such facilities and that can be contaminated with Naturally Occurring Radioactive Material (N.O.R.M.). As a result of oil processing, the natural radionuclides can be concentrated in such residues, forming the so called Technologically Enhanced Naturally Occurring Radioactive Material, or T.E.N.O.R.M.. Most of the radionuclides that appear in oil and gas streams belong to the 238 U and 232 Th natural series, besides 40 K. The present work was developed to determine the radionuclide content of scales and sludge generated during oil extraction and production operations. Emphasis was given to the quantification of 226 Ra, 228 Ra and 40 K since these radionuclides,are responsible for most of the external exposure in such facilities. Samples were taken from the P.E.T.R.O.B.R.A.S. unity in the State of Sergipe, in Northeastern Brazil. They were collected directly from the inner surface of water pipes and storage tanks, or from barrels stored in the waste storage area of the E and P unit. The activity concentrations for 226 Ra, 228 Ra and 40 K were determined by using an HP Ge gamma spectrometric system. The results showed concentrations ranging from 42.7 to 2,110.0 kBq/kg for 226 Ra, 40.5 to 1,550.0 kBq/kg for 228 Ra, and 20.6 to 186.6 kBq/kg for 40 K. The results highlight the importance of determining the activity concentration of those radionuclides in oil residues before deciding whether they should be stored or discarded to the environment. (authors)

  17. Natural radioactivity in petroleum residues

    Energy Technology Data Exchange (ETDEWEB)

    Gazineu, M.H.P. [UNICAP, Dept. de Quimica, Recife (Brazil); Gazineu, M.H.P.; Hazin, C.A. [UFPE, Dept. de Energia Nuclear, Recife (Brazil); Hazin, C.A. [Centro Regional de Ciencias Nucleares/ CNEN, Recife (Brazil)

    2006-07-01

    The oil extraction and production industry generates several types of solid and liquid wastes. Scales, sludge and water are typical residues that can be found in such facilities and that can be contaminated with Naturally Occurring Radioactive Material (N.O.R.M.). As a result of oil processing, the natural radionuclides can be concentrated in such residues, forming the so called Technologically Enhanced Naturally Occurring Radioactive Material, or T.E.N.O.R.M.. Most of the radionuclides that appear in oil and gas streams belong to the {sup 238}U and {sup 232}Th natural series, besides 40 K. The present work was developed to determine the radionuclide content of scales and sludge generated during oil extraction and production operations. Emphasis was given to the quantification of {sup 226}Ra, {sup 228}Ra and 40 K since these radionuclides,are responsible for most of the external exposure in such facilities. Samples were taken from the P.E.T.R.O.B.R.A.S. unity in the State of Sergipe, in Northeastern Brazil. They were collected directly from the inner surface of water pipes and storage tanks, or from barrels stored in the waste storage area of the E and P unit. The activity concentrations for {sup 226}Ra, {sup 228}Ra and 40 K were determined by using an HP Ge gamma spectrometric system. The results showed concentrations ranging from 42.7 to 2,110.0 kBq/kg for {sup 226}Ra, 40.5 to 1,550.0 kBq/kg for {sup 228}Ra, and 20.6 to 186.6 kBq/kg for 40 K. The results highlight the importance of determining the activity concentration of those radionuclides in oil residues before deciding whether they should be stored or discarded to the environment. (authors)

  18. Residual Liquefaction under Standing Waves

    DEFF Research Database (Denmark)

    Kirca, V.S. Ozgur; Sumer, B. Mutlu; Fredsøe, Jørgen

    2012-01-01

    This paper summarizes the results of an experimental study which deals with the residual liquefaction of seabed under standing waves. It is shown that the seabed liquefaction under standing waves, although qualitatively similar, exhibits features different from that caused by progressive waves....... The experimental results show that the buildup of pore-water pressure and the resulting liquefaction first starts at the nodal section and spreads towards the antinodal section. The number of waves to cause liquefaction at the nodal section appears to be equal to that experienced in progressive waves for the same...

  19. Process to recycle shredder residue

    Science.gov (United States)

    Jody, Bassam J.; Daniels, Edward J.; Bonsignore, Patrick V.

    2001-01-01

    A system and process for recycling shredder residue, in which separating any polyurethane foam materials are first separated. Then separate a fines fraction of less than about 1/4 inch leaving a plastics-rich fraction. Thereafter, the plastics rich fraction is sequentially contacted with a series of solvents beginning with one or more of hexane or an alcohol to remove automotive fluids; acetone to remove ABS; one or more of EDC, THF or a ketone having a boiling point of not greater than about 125.degree. C. to remove PVC; and one or more of xylene or toluene to remove polypropylene and polyethylene. The solvents are recovered and recycled.

  20. Residual replacement strategies for Krylov subspace iterative methods for the convergence of true residuals

    NARCIS (Netherlands)

    Vorst, H.A. van der; Ye, Q.

    1999-01-01

    In this paper, a strategy is proposed for alternative computations of the residual vectors in Krylov subspace methods, which improves the agreement of the computed residuals and the true residuals to the level of O(u)kAkkxk. Building on earlier ideas on residual replacement and on insights in

  1. Residual stress measurements of welded stainless steel 304 plate using the HANARO residual stress instrument

    International Nuclear Information System (INIS)

    Mun, M. K.; Lee, C. H.; Em, V. T.

    2001-01-01

    In order to nondestructively measure in-depth residual stress distribution of the metallic materials, it is unique method to use neutron diffraction. In this paper the principles of residual stress measurements by neutron diffraction is described. The residual stress distribution of welded strainless steeel 304 plate using te HANARO residual stress instrument is also described

  2. 40 CFR 721.4500 - Isopropylamine distillation residues and ethylamine distillation residues.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Isopropylamine distillation residues and ethylamine distillation residues. 721.4500 Section 721.4500 Protection of Environment... residues and ethylamine distillation residues. (a) Chemical substances and significant new use subject to...

  3. Residual analysis for spatial point processes

    DEFF Research Database (Denmark)

    Baddeley, A.; Turner, R.; Møller, Jesper

    process. Residuals are ascribed to locations in the empty background, as well as to data points of the point pattern. We obtain variance formulae, and study standardised residuals. There is also an analogy between our spatial residuals and the usual residuals for (non-spatial) generalised linear models...... or covariate effects. Q-Q plots of the residuals are effective in diagnosing interpoint interaction. Some existing ad hoc statistics of point patterns (quadrat counts, scan statistic, kernel smoothed intensity, Berman's diagnostic) are recovered as special cases....

  4. Cycling of grain legume residue nitrogen

    DEFF Research Database (Denmark)

    Jensen, E.S.

    1995-01-01

    weeks of decomposition, due to high rates of residue N net mineralization and subsequent leaching and denitrification losses of N. Lysimeter experiments showed that pea residues may reduce leaching losses of N, probably due to their effect on the mineralization-immobilizalion turnover of N...... and denitrification. Winter barley succeeding field pea recovered 13% of the incorporated pea residue N by early December; the recovery was found to be 15% at maturity in July. A spring-sown crop of barley recovered less than half the amount of pea residue N recovered by winter barley. The residue N-use efficiencies...

  5. Marked pericardial inhomogeneity of specific ventilation at total lung capacity and beyond

    DEFF Research Database (Denmark)

    Sun, Yanping; Butler, James P; Lindholm, Peter

    2009-01-01

    uniform at FRC+1L, with a small non-gravitational cephalocaudal gradient of specific ventilation in the supine posture. Our observations at high lung volumes are consistent with the effect of high pleural tension in the concave pericardial region, which promotes expansion of the subjacent lung, leading...

  6. Phosphorus Recovery Using Zirconium-Loaded Saponified Orange Juice Residue

    Science.gov (United States)

    Harada, Hiroyuki; Kondo, Mitsunori; Biswas, Biplob K.; Ohura, Seichirou; Inoue, Katsutoshi; Ishikawa, Susumu; Kawakita, Hidetaka; Ohto, Keisuke

    Zirconium was immobilized to orange juice residue, to investigate the feasibility of using zirconium-loaded saponified orange juice residue (Zr-SOJR) for phosphorus recovery from secondary effluent and the extraction solution from incinerated sewage sludge ash by using H2SO4 and HCl. These had phosphorus concentrations of 68.2 mg/dm3 and 5.9 mg/dm3, respectively. The phosphorus removal rate secondary effluent increased with an increasing solid/liquid ratio in batch experiments. The adsorption capacity of Zr-SOJR was also compared with those obtained using a synthetic phosphorus solution and using zirconium-loaded ferrite. The prepared absorbent was effective for phosphorus removal and exhibited a reasonably high sorption capacity, twice that of zirconium ferrite. Secondary effluent was treated by packed column, and this reached break-through after 300 bed volumes. The results from phosphorous extraction from the ash indicate that can be treated with acid to efficiently recover phosphorous and thus can be absorbed by Zr-SOJR.

  7. Monitoring antibiotic residues in honey

    Directory of Open Access Journals (Sweden)

    Monica Cristina Cara,

    2011-12-01

    Full Text Available Next to the beta-lactam antibiotics in veterinary medicine, streptomycin is one of the mostly used antibiotics. High concentration of streptomycin could lead to ototoxic and nephrotoxic effects. Low concentration – as found in food – may cause allergies, destroy the intestinal flora and favor immunity to some pathogenic microorganisms. In 1948 chlortetracycline was isolated by Duggan as a metabolite and this was the first antibiotic substance of the group of tetracyclines. In the present paper there are presented the monitoring of the antibiotic residues in honey from Timis County. The residues of tetracycline and streptomycin in honey were determined by the method ELISA – a quantitative method of detection. The microtitre wells are coated with tetracycline and anti-streptomycin antibodies. Free antibiotic and immobilized antibiotic compete with the added antibiotic antibody (competitive immunoassay reaction. Any unbound antibody is then removed in a washing step. Bound conjugate enzymes convert the colorless chromogen into a blue product. The addition ofthe stop reagent leads to a color change from blue to yellow. The measurement is made photometrically at 450 nm. The absorption is inversely proportional to the antibiotic concentration in the sample.

  8. Residual Stresses In 3013 Containers

    International Nuclear Information System (INIS)

    Mickalonis, J.; Dunn, K.

    2009-01-01

    The DOE Complex is packaging plutonium-bearing materials for storage and eventual disposition or disposal. The materials are handled according to the DOE-STD-3013 which outlines general requirements for stabilization, packaging and long-term storage. The storage vessels for the plutonium-bearing materials are termed 3013 containers. Stress corrosion cracking has been identified as a potential container degradation mode and this work determined that the residual stresses in the containers are sufficient to support such cracking. Sections of the 3013 outer, inner, and convenience containers, in both the as-fabricated condition and the closure welded condition, were evaluated per ASTM standard G-36. The standard requires exposure to a boiling magnesium chloride solution, which is an aggressive testing solution. Tests in a less aggressive 40% calcium chloride solution were also conducted. These tests were used to reveal the relative stress corrosion cracking susceptibility of the as fabricated 3013 containers. Significant cracking was observed in all containers in areas near welds and transitions in the container diameter. Stress corrosion cracks developed in both the lid and the body of gas tungsten arc welded and laser closure welded containers. The development of stress corrosion cracks in the as-fabricated and in the closure welded container samples demonstrates that the residual stresses in the 3013 containers are sufficient to support stress corrosion cracking if the environmental conditions inside the containers do not preclude the cracking process.

  9. Residual Fragments after Percutaneous Nephrolithotomy

    Directory of Open Access Journals (Sweden)

    Kaan Özdedeli

    2012-09-01

    Full Text Available Clinically insignificant residual fragments (CIRFs are described as asymptomatic, noninfectious and nonobstructive stone fragments (≤4 mm remaining in the urinary system after the last session of any intervention (ESWL, URS or PCNL for urinary stones. Their insignificance is questionable since CIRFs could eventually become significant, as their presence may result in recurrent stone growth and they may cause pain and infection due to urinary obstruction. They may become the source of persistent infections and a significant portion of the patients will have a stone-related event, requiring auxilliary interventions. CT seems to be the ultimate choice of assessment. Although there is no concensus about the timing, recent data suggests that it may be performed one month after the procedure. However, imaging can be done in the immediate postoperative period, if there are no tubes blurring the assessment. There is some evidence indicating that selective medical therapy may have an impact on decreasing stone formation rates. Retrograde intrarenal surgery, with its minimally invasive nature, seems to be the best way to deal with residual fragments.

  10. Study on increasing spent fuel storage capacity at Juragua NPP

    International Nuclear Information System (INIS)

    Guerra Valdes, R.; Lopez Aldama, D.; Rodriguez Gual, M.; Garcia Yip, F.

    1999-01-01

    The delay in decision about the final disposal of the spent fuel, led to longer interim storage. The reracking og the storage pools was an economical and feasible option to increase the storage capacity on the site. Reracking of the storage facility led to the analysis of the new conditions for criticality, shielding, residual heat removal and mechanical loads over the structures. This paper includes a summary of the studies on criticality and dose rate changes in the vicinity of the storage pool of Juragua NPP

  11. Analysis of residual stress relief mechanisms in post-weld heat treatment

    International Nuclear Information System (INIS)

    Dong, Pingsha; Song, Shaopin; Zhang, Jinmiao

    2014-01-01

    This paper presents a recent study on weld residual stress relief mechanisms associated with furnace-based uniform post-weld heat treatment (PWHT). Both finite element and analytical methods are used to quantitatively examine how plastic deformation and creep relaxation contribute to residual stress relief process at different stages of PWHT process. The key contribution of this work to an improved understanding of furnace based uniform PWHT can be summarized as follows: (1)Plastic deformation induced stress relief during PWHT can be analytically expressed by the change in material elastic deformation capacity (or elastic deformation limit) measured in terms of material yield strength to Young's modulus ratio, which has a rather limited role in overall residual stress relief during furnace based uniform PWHT. (2)The most dominant stress relief mechanism is creep strain induced stress relaxation, as expected. However, a rapid creep strain development accompanied by a rapid residual stress reduction during heating stage before reaching PWHT temperature is shown to contribute to most of the stress relief seen in overall PWHT process, suggesting PWHT hold time can be significantly reduced as far as residual stress relief is concerned. (3)A simple engineering scheme for estimating residual stress reduction is proposed based on this study by relating material type, PWHT temperature, and component wall thickness. - Highlights: • The paper clarified effects of plastic deformation and creep relaxation on weld residual stress relief during uniform PWHT. • Creep strain development is far more important than plastic strain, mostly completed even before hold time starts. • Plastic strain development is insignificant and be analytically described by a material elastic deformation capacity parameter. • An engineering estimation scheme is proposed for determining residual stress reduction resulted from furnace based PWHT

  12. Absorptive capacity and smart companies

    Directory of Open Access Journals (Sweden)

    Patricia Moro González

    2014-12-01

    Full Text Available Purpose: The current competitive environment is substantially modifying the organizations’ learning processes due to a global increase of available information allowing this to be transformed into knowledge. This opportunity has been exploited since the nineties by the tools of “Business Analytics” and “Business Intelligence” but, nevertheless, being integrated in the study of new organizational capacities engaged in the process of creating intelligence inside organizations is still an outstanding task. The review of the concept of absorptive capacity and a detailed study from the perspective of this new reality will be the main objective of study of this paper.Design/methodology/approach: By comparing classical absorptive capacity and absorptive capacity from the point of view of information management tools in each one of the three stages of the organizational learning cycle, some gaps of the former are overcome/fulfilled. The academic/bibliographical references provided in this paper have been obtained from ISI web of knowledge, Scopus and Dialnet data bases, supporting the state of affairs on absorptive capacity and thereafter filtering by "Business Intelligence" and "Business Analytics". Specialized websites and Business Schools` Publications there have also been included, crowning the content on information management tools used that are currently used in the strategic consulting.Findings: Our contribution to the literature is the development of "smart absorptive capacity". This is a new capacity emerging from the reformulation of the classical concept of absorptive capacity wherein some aspects of its definition that might have been omitted are emphasized. The result of this new approach is the creation of a new Theoretical Model of Organizational Intelligence, which aims to explain, within the framework of the Resources and Capabilities Theory, the competitive advantage achieved by the so-called smart companies

  13. Improving African health research capacity

    DEFF Research Database (Denmark)

    Lazarus, Jeff; Wallace, Samantha A; Liljestrand, Jerker

    2010-01-01

    The issue of strengthening local research capacity in Africa is again high on the health and development agenda. The latest initiative comes from the Wellcome Trust. But when it comes to capacity development, one of the chief obstacles that health sectors in the region must confront is the migrat...... of beneficial research capacity in the countries of sub-Saharan Africa, this article suggests several recommendations to both donors and governments that have broad application for general health research issues in the region.......The issue of strengthening local research capacity in Africa is again high on the health and development agenda. The latest initiative comes from the Wellcome Trust. But when it comes to capacity development, one of the chief obstacles that health sectors in the region must confront...... is the migration of health professionals to countries that offer more lucrative opportunities, like those in western Europe. To combat this ''brain drain'', already back in 1984, the Swedish International Development Cooperation Agency (Sida) created a training programme in which healthcare professionals from...

  14. Biochemical suitability of crop residues for cellulosic ethanol: disincentives to nitrogen fertilization in corn agriculture.

    Science.gov (United States)

    Gallagher, Morgan E; Hockaday, William C; Masiello, Caroline A; Snapp, Sieglinde; McSwiney, Claire P; Baldock, Jeffrey A

    2011-03-01

    Concerns about energy security and climate change have increased biofuel demand, particularly ethanol produced from cellulosic feedstocks (e.g., food crop residues). A central challenge to cropping for cellulosic ethanol is the potential environmental damage from increased fertilizer use. Previous analyses have assumed that cropping for carbohydrate in residue will require the same amount of fertilizer as cropping for grain. Using (13)C nuclear magnetic resonance, we show that increases in biomass in response to fertilization are not uniform across biochemical classes (carbohydrate, protein, lipid, lignin) or tissues (leaf and stem, grain, reproductive support). Although corn grain responds vigorously and nonlinearly, corn residue shows only modest increases in carbohydrate yields in response to high levels of fertilization (25% increase with 202 kg N ha(-1)). Lignin yields in the residue increased almost twice as much as carbohydrate yields in response to nitrogen, implying that residue feedstock quality declines as more fertilizer is applied. Fertilization also increases the decomposability of corn residue, implying that soil carbon sequestration becomes less efficient with increased fertilizer. Our results suggest that even when corn is grown for grain, benefits of fertilization decline rapidly after the ecosystem's N demands are met. Heavy application of fertilizer yields minimal grain benefits and almost no benefits in residue carbohydrates, while degrading the cellulosic ethanol feedstock quality and soil carbon sequestration capacity.

  15. Manual of Standard Operating Procedures for Veterinary Drug Residue Analysis (French Edition)

    International Nuclear Information System (INIS)

    2017-01-01

    Laboratories are crucial to national veterinary drug residue monitoring programmes. However, one of the main challenges laboratories encounter is obtaining access to relevant methods of analysis. Thus, in addition to training, providing technical advice and transferring technology, the Joint FAO/IAEA Division of Nuclear Techniques in Food and Agriculture has resolved to develop clear and practical manuals to support Member State laboratories. The Coordinated Research Project (CRP) on Development of Radiometric and Allied Analytical Methods to Strengthen Residue Control Programs for Antibiotic and Anthelmintic Veterinary Drug Residues has developed a number of analytical methods as standard operating procedures (SOPs), which are now compiled here. This publication contains SOPs on chromatographic and spectrometric techniques, as well as radioimmunoassay and associated screening techniques, for various anthelmintic and antimicrobial veterinary drug residue analysis. Some analytical method validation protocols are also included. The publication is primarily aimed at food and environmental safety laboratories involved in testing veterinary drug residues, including under organized national residue monitoring programmes. It is expected to enhance laboratory capacity building and competence through the use of radiometric and complementary tools and techniques. The publication is also relevant for applied research on residues of veterinary drugs in food and environmental samples

  16. Manual of Standard Operating Procedures for Veterinary Drug Residue Analysis (Spanish Edition)

    International Nuclear Information System (INIS)

    2017-01-01

    Laboratories are crucial to national veterinary drug residue monitoring programmes. However, one of the main challenges laboratories encounter is obtaining access to relevant methods of analysis. Thus, in addition to training, providing technical advice and transferring technology, the Joint FAO/IAEA Division of Nuclear Techniques in Food and Agriculture has resolved to develop clear and practical manuals to support Member State laboratories. The Coordinated Research Project (CRP) on Development of Radiometric and Allied Analytical Methods to Strengthen Residue Control Programs for Antibiotic and Anthelmintic Veterinary Drug Residues has developed a number of analytical methods as standard operating procedures (SOPs), which are now compiled here. This publication contains SOPs on chromatographic and spectrometric techniques, as well as radioimmunoassay and associated screening techniques, for various anthelmintic and antimicrobial veterinary drug residue analysis. Some analytical method validation protocols are also included. The publication is primarily aimed at food and environmental safety laboratories involved in testing veterinary drug residues, including under organized national residue monitoring programmes. It is expected to enhance laboratory capacity building and competence through the use of radiometric and complementary tools and techniques. The publication is also relevant for applied research on residues of veterinary drugs in food and environmental samples

  17. Effect of corrosion on the buckling capacity of tubular members

    Science.gov (United States)

    Øyasæter, F. H.; Aeran, A.; Siriwardane, S. C.; Mikkelsen, O.

    2017-12-01

    Offshore installations are subjected to harsh marine environment and often have damages from corrosion. Several experimental and numerical studies were performed in the past to estimate buckling capacity of corroded tubular members. However, these studies were either based on limited experimental tests or numerical analyses of few cases resulting in semi-empirical relations. Also, there are no guidelines and recommendations in the currently available design standards. To fulfil this research gap, a new formula is proposed to estimate the residual strength of tubular members considering corrosion and initial geometrical imperfections. The proposed formula is verified with results from finite element analyses performed on several members and for varying corrosion patch parameters. The members are selected to represent the most relevant Eurocode buckling curve for tubular members. It is concluded that corrosion reduces the buckling capacity significantly and the proposed formula can be easily applied by practicing engineers without performing detailed numerical analyses.

  18. Turning wood residues into wood revenues

    International Nuclear Information System (INIS)

    Graham, R.G.; Kravetz, Don

    1996-01-01

    Ensyn is a profitable commercial company which derives its revenues from the conversion of wood residues into liquid biofuel and chemicals. The technology, Rapid Thermal Processing (RTP (TM) )is based on extremely fast ''cracking'' of biomass which results in light liquid yields exceeding 70% by weight, from wood. Whether producing chemicals or liquid biofuel, the RTP plant is configured identically and operated essentially in the same mode. Chemicals production simply allows economical production to occur at a lower plant capacity, as low as 2 tonnes/day, than is feasible for a dedicated fuel plant (typically greater than 100 tonnes/day). Ensyn has developed the commercialisation of RTP TM from bench to industrial scale in 10 years. A variety of crative funding initiatives in the early years allowed for capital to be raised for R and D without the loss of intellectual property (IP). The transition years of technology demonstration, prior to full commercialisation, were funded by a blend of revenues from venture capital and public sources, and by quickly tapping into a niche market for RTP TM . The utilisation of the technology at the niche market scale opened the doors to the larger fuel and commodity markets. Once, again, both IP and control of the company were maintained during these years. Flexibility, creativity and expertise are necessary to understand the significance of various financing options (private investments, commercial banking and bond issues) and to integrate these options with various renewable energy, recycling and tax incentives. Understanding these options with various renewable energy, recycling and tax incentives is necessary. Understanding both the core and peripheral needs of the customer are essential in successfully advancing a commercial wood energy venture. Ensyn's experience in these areas is the focus of the paper. (Author)

  19. Capacity Utilization in European Railways

    DEFF Research Database (Denmark)

    Khadem Sameni, Melody; Landex, Alex

    2013-01-01

    At the strategic level, railways currently use different indices to estimate how ‘value’ is generated by using railway capacity. However, railway capacity is a multidisciplinary area, and attempts to develop various indices cannot provide a holistic measure of operational efficiency. European...... and unprecedented approach for this aim. Relative operational efficiency of 24 European railways in capacity utilization is studied for the first time by data envelopment analysis (DEA). It deviates from previous applications of DEA in the railway industry that are conducted to analyze cost efficiency of railways...... aspects of railway services in European countries has recently been quantified by European commission and are used for the first time in the literature. Invaluable insights can be inferred from the results which can provide a ground basis for railway practitioners and policy makers....

  20. Warfare, Fiscal Capacity, and Performance

    DEFF Research Database (Denmark)

    Prado, Mauricio; Dincecco, Mark

    innovations, which persisted and helped to shape current fiscal institutions. Economic historians claim that greater fiscal capacity was the key long-run institutional change brought about by historical conflicts. Using casualties sustained in pre-modern wars to instrument for current fiscal institutions, we......We exploit differences in casualties sustained in pre-modern wars to estimate the impact of fiscal capacity on economic performance. In the past, states fought different amounts of external conflicts, of various lengths and magnitudes. To raise the revenues to wage wars, states made fiscal...... estimate substantial impacts of fiscal capacity on GDP per worker. The results are robust to a broad range of specifications, controls, and sub-samples....

  1. Warfare, Fiscal Capacity, and Performance

    DEFF Research Database (Denmark)

    Dincecco, Mark; Prado, Mauricio

    2012-01-01

    innovations, which persisted and helped to shape current fiscal institutions. Economic historians claim that greater fiscal capacity was the key long-run institutional change brought about by historical conflicts. Using casualties sustained in pre-modern wars to instrument for current fiscal institutions, we......We exploit differences in casualties sustained in pre-modern wars to estimate the impact of fiscal capacity on economic performance. In the past, states fought different amounts of external conflicts, of various lengths and magnitudes. To raise the revenues to wage wars, states made fiscal...... estimate substantial impacts of fiscal capacity on GDP per worker. The results are robust to a broad range of specifications, controls, and sub-samples....

  2. THE LEGAL CAPACITY TO TRADE

    Directory of Open Access Journals (Sweden)

    ADELIN UNGUREANU

    2014-12-01

    Full Text Available Trading is a part of our society. The man has been trading from ancient times so the amount of trades and transactions around the world is huge. In order for us to initiate, organize and deploy such trades we have to have certain rules which can help regulate the social and professional or legal aspect of trades. Therefore the sole trader capacity must be obtained and used in order for the contracts to be valid. The right and obligations that come with this capacity constitute activities that can be reflected and analysed by obtaining and maintain the sole trader status.

  3. THE LEGAL CAPACITY TO TRADE

    OpenAIRE

    ADELIN UNGUREANU

    2014-01-01

    Trading is a part of our society. The man has been trading from ancient times so the amount of trades and transactions around the world is huge. In order for us to initiate, organize and deploy such trades we have to have certain rules which can help regulate the social and professional or legal aspect of trades. Therefore the sole trader capacity must be obtained and used in order for the contracts to be valid. The right and obligations that come with this capacity constitute activities t...

  4. Managing Capacity by Drift Control

    OpenAIRE

    Ormeci Matoglu, Melda; Vande Vate, John

    2009-01-01

    We model the problem of managing capacity in a build-to-order environment as a Brownian drift control problem and seek a policy that minimizes the long-term average cost. We assume the controller can, at some cost, shift the processing rate among a finite set of alternatives by, for example, adding or removing staff, increasing or reducing the number of shifts or opening or closing production lines. The controller incurs a cost for capacity per unit time and a delay cost that reflects th...

  5. Norepinephrine transporter function and desipramine: residual drug effects versus short-term regulation.

    Science.gov (United States)

    Ordway, Gregory A; Jia, Weihong; Li, Jing; Zhu, Meng-Yang; Mandela, Prashant; Pan, Jun

    2005-04-30

    Previous research has shown that exposure of norepinephrine transporter (NET)-expressing cells to desipramine (DMI) downregulates the norepinephrine transporter, although changes in the several transporter parameters do not demonstrate the same time course. Exposures to desipramine for effects of residual desipramine on norepinephrine transporter binding and uptake were re-evaluated following exposures of PC12 cells to desipramine using different methods to remove residual drug. Using a method that minimizes residual drug, exposure of intact PC12 cells to desipramine for 4h had no effect on uptake capacity or [(3)H]nisoxetine binding to the norepinephrine transporter, while exposures for > or =16 h reduced uptake capacity. Desipramine-induced reductions in binding to the transporter required >24 h or greater periods of desipramine exposure. This study confirms that uptake capacity of the norepinephrine transporter is reduced earlier than changes in radioligand binding, but with a different time course than originally shown. Special pre-incubation procedures are required to abolish effects of residual transporter inhibitor when studying inhibitor-induced transporter regulation.

  6. MORTAR WITH UNSERVICEABLE TIRE RESIDUES

    Directory of Open Access Journals (Sweden)

    J. A. Canova

    2009-01-01

    Full Text Available This study analyzes the effects of unserviceable tire residues on rendering mortar using lime and washed sand at a volumetric proportion of 1:6. The ripened composite was dried in an oven and combined with both cement at a volumetric proportion of 1:1.5:9 and rubber powder in proportional aggregate volumes of 6, 8, 10, and 12%. Water exudation was evaluated in the plastic state. Water absorption by capillarity, fresh shrinkage and mass loss, restrained shrinkage and mass loss, void content, flexural strength, and deformation energy under compression were evaluated in the hardened state. There was an improvement in the water exudation and water absorption by capillarity and drying shrinkage, as well as a reduction of the void content and flexural strength. The product studied significantly aided the water exudation from mortar and, capillary elevation in rendering.

  7. MORTAR WITH UNSERVICEABLE TIRE RESIDUES

    Directory of Open Access Journals (Sweden)

    José Aparecido Canova

    2009-12-01

    Full Text Available This study analyzes the effects of unserviceable tire residues on rendering mortar using lime and washed sand at a volumetric proportion of 1:6. The ripened composite was dried in an oven and combined with both cement at a volumetric proportion of 1:1.5:9 and rubber powder in proportional aggregate volumes of 6, 8, 10, and 12%. Water exudation was evaluated in the plastic state. Water absorption by capillarity, fresh shrinkage and mass loss, restrained shrinkage and mass loss, void content, flexural strength, and deformation energy under compression were evaluated in the hardened state. There was an improvement in the water exudation and water absorption by capillarity and drying shrinkage, as well as a reduction of the void content and flexural strength. The product studied significantly aided the water exudation from mortar and, capillary elevation in rendering.

  8. Landfill Mining of Shredder Residues

    DEFF Research Database (Denmark)

    Hansen, Jette Bjerre; Hyks, Jiri; Shabeer Ahmed, Nassera

    In Denmark, shredder residues (SR) are classified as hazardous waste and until January 2012 the all SR were landfilled. It is estimated that more than 1.8 million tons of SR have been landfilled in mono cells. This paper describes investigations conducted at two Danish landfills. SR were excavated...... from the landfills and size fractionated in order to recover potential resources such as metal and energy and to reduce the amounts of SR left for re-landfilling. Based on the results it is estimated that 60-70% of the SR excavated could be recovered in terms of materials or energy. Only a fraction...... with particle size less than 5 mm needs to be re-landfilled at least until suitable techniques are available for recovery of materials with small particle sizes....

  9. Forest residues in cattle feed

    Directory of Open Access Journals (Sweden)

    João Elzeário Castelo Branco Iapichini

    2012-12-01

    Full Text Available The ruminants are capable of converting low-quality food, when they are complementes with high-energy source. Through the use of regional agricultural residues is possible to conduct more economical production systems, since energetic foods have high cost in animal production. There is very abundant availability of residues in agroforestry activities worldwide, so that if a small fraction of them were used with appropriate technical criteria they could largely meet the needs of existing herds in the world and thus meet the demands of consumption of protein of animal origin. The Southwest Region of São Paulo State has large area occupied by reforestation and wide availability of non-timber forest residues, which may represent more concentrated energetic food for ruminant production. This experiment aimed to evaluate the acceptability of ground pine (20, 30 and 40%, replacing part of the energetic food (corn, present in the composition of the concentrate and was performed at the Experimental Station of Itapetininga - Forest Institute / SMA, in the dry season of 2011. It were used four crossbred steers, mean 18 months old, average body weight of 250 kg, housed in a paddock provided with water ad libitum and covered troughs for supplementation with the experimental diet. The adjustment period of the animals was of 07 days and the measurement of the levels of consumption, physiological changes, acceptability and physiological parameters were observed during the following 25 days. The concentrate supplement was formulated based on corn (76.2%, Soybean Meal (20%, urea (2%, Ammonium sulfate (0.4%, calcite (1.4%, Mineral Core (1% and finely ground Pine Cone, replacing corn. In preparing food, the formulas were prepared to make them isoproteic/energetic, containing the following nutrient levels: 22% Crude Protein (CP and 79% of Total Nutrients (TDN. The animals received the supplement in three steps for each level of cone replaced, being offered in the

  10. Detection of antibiotic residues in poultry meat.

    Science.gov (United States)

    Sajid, Abdul; Kashif, Natasha; Kifayat, Nasira; Ahmad, Shabeer

    2016-09-01

    The antibiotic residues in poultry meat can pose certain hazards to human health among them are sensitivity to antibiotics, allergic reactions, mutation in cells, imbalance of intestinal micro biota and bacterial resistance to antibiotics. The purpose of the present paper was to detect antibiotic residue in poultry meat. During the present study a total of 80 poultry kidney and liver samples were collected and tested for detection of different antibiotic residues at different pH levels Eschericha coli at pH 6, 7 and Staphyloccocus aureus at pH 8 & 9. Out of 80 samples only 4 samples were positive for antibiotic residues. The highest concentrations of antibiotic residue found in these tissues were tetracycline (8%) followed by ampicilin (4%), streptomycine (2%) and aminoglycosides (1%) as compared to other antibiotics like sulfonamides, neomycine and gentamycine. It was concluded that these microorganism at these pH levels could be effectively used for detection of antibiotic residues in poultry meat.

  11. Predictive hydrogeochemical modelling of bauxite residue sand in field conditions.

    Science.gov (United States)

    Wissmeier, Laurin; Barry, David A; Phillips, Ian R

    2011-07-15

    The suitability of residue sand (the coarse fraction remaining from Bayer's process of bauxite refining) for constructing the surface cover of closed bauxite residue storage areas was investigated. Specifically, its properties as a medium for plant growth are of interest to ensure residue sand can support a sustainable ecosystem following site closure. The geochemical evolution of the residue sand under field conditions, its plant nutrient status and soil moisture retention were studied by integrated modelling of geochemical and hydrological processes. For the parameterization of mineral reactions, amounts and reaction kinetics of the mineral phases natron, calcite, tricalcium aluminate, sodalite, muscovite and analcime were derived from measured acid neutralization curves. The effective exchange capacity for ion adsorption was measured using three independent exchange methods. The geochemical model, which accounts for mineral reactions, cation exchange and activity corrected solution speciation, was formulated in the geochemical modelling framework PHREEQC, and partially validated in a saturated-flow column experiment. For the integration of variably saturated flow with multi-component solute transport in heterogeneous 2D domains, a coupling of PHREEQC with the multi-purpose finite-element solver COMSOL was established. The integrated hydrogeochemical model was applied to predict water availability and quality in a vertical flow lysimeter and a cover design for a storage facility using measured time series of rainfall and evaporation from southwest Western Australia. In both scenarios the sand was fertigated and gypsum-amended. Results show poor long-term retention of fertilizer ions and buffering of the pH around 10 for more than 5 y of leaching. It was concluded that fertigation, gypsum amendment and rainfall leaching alone were insufficient to render the geochemical conditions of residue sand suitable for optimal plant growth within the given timeframe. The

  12. Research projects and capacity building

    African Journals Online (AJOL)

    driniev

    2004-10-04

    Oct 4, 2004 ... strategic alliances interacting in a learning environment that is supported by enabling conditions, we appreciate that capacity building in research projects is not the sole responsibility of the researchers. The responsibility must be shared amongst those individuals and institutions who promote research (for ...

  13. Freeway work zone lane capacity.

    Science.gov (United States)

    2009-01-01

    The focus of this report is a capacity analysis of two long-term urban freeway Work Zones. Work Zone #1 : tapered four mainline lanes to two, using two separate tapers; Work Zone #2 tapered two mainline lanes to one. : Work Zone throughput was analyz...

  14. Model of clinker capacity expansion

    CSIR Research Space (South Africa)

    Stylianides, T

    1998-10-01

    Full Text Available to be introduced each year during a given planning horizon. The optimal solution is defined as the one which maximises the net present value (NPV) of the cash flow generated by the introduction and operation of new kilns subject to capacity and demand constraints...

  15. North American fertilizer capacity data

    Energy Technology Data Exchange (ETDEWEB)

    1991-12-01

    This listing of producers and their fertilizer production capacities was compiled in October 1991 with the cooperation of the US and Canadian fertilizer industries. Yearly production and forecasts are given for 1987 through 1997. Fertilizers reported on include: ammonium sulfate, nitric acid, wet-process superphosphoric acid, normal superphosphate, elemental phosphorus, potassium sulfate, and sulfate of potash/magnesia.

  16. North American fertilizer capacity data

    Energy Technology Data Exchange (ETDEWEB)

    1991-12-01

    This listing of producers and their fertilizer production capacities was compiled in October 1991 with the cooperation of the US and Canadian fertilizer industry. Fertilizers production is reported or forecasted for the years 1987 through 1997. The fertilizers reported on are: ammonia, ammonium nitrate, nitrogen solutions, urea, phosphate rock, wet-process phosphoric acid, ammonium phosphates, concentrated superphosphates, and potash.

  17. Antioxidant capacity and physical exercise

    Directory of Open Access Journals (Sweden)

    A Marciniak

    2009-09-01

    Full Text Available The aim of this article is a presentation of current knowledge regarding the changes of plasma antioxidant capacity observed in response to physical exercise. Human body created the enzymatic and non-enzymatic systems, which play a protective role in the harmful impact of free radicals. Those two systems constitute what is known as the plasma total antioxidant capacity. The amount of reactive oxygen species (ROS and reactive nitrogen species (NOS in combination with oxidation processes increases in some tissues during physiological response to physical exercise. These changes are observed after single bout of exercise as well as after regular training. The response of human body to physical exercise can be analysed using various models of exercise test. Application of repeated type of exhaustion allows for characterizing the ability of human body to adjust to the increased energy loss and increased oxygen consumption. This article presents the characteristics of components of plasma antioxidant capacity, the mechanisms of free radicals production and their role in human body. It discusses also the currently used methods of detecting changes in total antioxidant capacity and its individual elements in response to single bout of exercise and regular training. It presents the review of literature about research performed in groups of both regularly training and low exercise activity individuals as well as in group of healthy subjects and patients with circulation diseases.

  18. Comparative antioxidant capacity, membrane stabilization ...

    African Journals Online (AJOL)

    Comparative antioxidant capacity, membrane stabilization, polyphenol composition and cytotoxicity of the leaf and stem of Cissus multistriata. ... standard anti-inflammatory drug (Indomethacin) used. The extracts are less toxic to the cell (Arthenia salina) with their LC/EC50 higher than that of standard potassium dichromate ...

  19. Livelihood Resilience and Adaptive Capacity

    DEFF Research Database (Denmark)

    Thulstrup, Andreas Waaben

    2015-01-01

    This article analyses the implementation and outcomes of national development programs in a mountainous commune in Vietnam. The article traces the history of State intervention and the capacity of households and the community to adapt to change. The assessment reveals unintended consequences of t...

  20. Comparative antioxidant capacity, membrane stabilization ...

    African Journals Online (AJOL)

    STORAGESEVER

    2008-09-03

    Sep 3, 2008 ... In this present study, a comparative evaluation of the antioxidant capacities, phenol and polyphenol composition, membrane stabilization, and cytotoxicity to brine shrimps (Arthemia salina) of the leaf and stem extracts of Cissus multistriata were carried out. 2,2- Diphenyl-1-picryl hydrazyl (DPPH) radical.

  1. Distribution of residues and primitive roots

    Indian Academy of Sciences (India)

    Replacing the function f by g, we get the required estimate for N(p, N). D. Proof of Theorem 1.1. When p = 7, we clearly see that (1, 2) is a consecutive pair of quadratic residue modulo 7. Assume that p ≥ 11. If 10 is a quadratic residue modulo p, then we have (9, 10) as a consecutive pair of quadratic residues modulo p, ...

  2. Artificial Neural Networks and Concentration Residual Augmented ...

    African Journals Online (AJOL)

    Artificial Neural Networks and Concentration Residual Augmented Classical Least Squares for the Simultaneous Determination of Diphenhydramine, Benzonatate, Guaifenesin and Phenylephrine in their Quaternary Mixture.

  3. RESIDUES IN CARROTS TREATED WITH LINURON

    DEFF Research Database (Denmark)

    Løkke, Hans

    1974-01-01

    Investigations have been carried out on residues of linuron and its breakdown products in carrots sprayed with Jinuron at 1, 2, or 4 kg a.i./ha, 0, 19, 28, 36 or 60 days after sowing (up to 57 days before harvesting). The extracted residues were separated into three fractions by liquid......,4-dichloroaniline and iodide ion, followed by gas chromatography with electron capture detector. Only 5-13% of the extract-able residues were breakdown products. Most of the detectable residue (87-95%) was identified as linuron. The relative proportions of linuron and breakdown products in carrots at the time...

  4. The performance of activated carbons from sugarcane bagasse, babassu, and coconut shells in removing residual chlorine

    Directory of Open Access Journals (Sweden)

    E. F. Jaguaribe

    2005-03-01

    Full Text Available The capacity of activated carbons obtained from different raw materials, such as sugarcane bagasse, babassu (Orbygnia speciosa, and coconut (Cocus nucifera shells, to remove residual chlorine is studied. The influence of particle size and time of contact between particles of activated carbon and the chlorinated solution were taken into account. The adsorptive properties of the activated carbons were measured by gas adsorption (BET method, using an ASAP 2010 porosimeter, and liquid phase adsorption, employing iodine and methylene blue adsorbates. The activated carbon from sugarcane bagasse was the only adsorbent capable of removing 100% of the residual chlorine.

  5. Stability of the anthocyanins extracted from residues of the wine industry

    OpenAIRE

    Clemente, Edmar; Galli, Dirseu

    2011-01-01

    Anthocyanins are highly important due to their antioxidant capacity. They are the most important among the phenolic compounds and one of the main natural dyes used in the food industry. In this research, residue of processed grapes was used to investigate the presence of anthocyanins, the possibility of their extraction from the residue, and their stability. The extraction solution consisted of 70 mL of ethanol 70% and 30 mL of HCl 0.1% at pH 2.0. The results found for the processed grapes re...

  6. CO2 Separation and Capture Properties of Porous Carbonaceous Materials from Leather Residues

    Directory of Open Access Journals (Sweden)

    Ana Arenillas

    2013-10-01

    Full Text Available Carbonaceous porous materials derived from leather skin residues have been found to have excellent CO2 adsorption properties, with interestingly high gas selectivities for CO2 (α > 200 at a gas composition of 15% CO2/85% N2, 273K, 1 bar and capacities (>2 mmol·g−1 at 273 K. Both CO2 isotherms and the high heat of adsorption pointed to the presence of strong binding sites for CO2 which may be correlated with both: N content in the leather residues and ultrasmall pore sizes.

  7. CO2 Separation and Capture Properties of Porous Carbonaceous Materials from Leather Residues

    Science.gov (United States)

    Bermúdez, José M.; Dominguez, Pablo Haro; Arenillas, Ana; Cot, Jaume; Weber, Jens; Luque, Rafael

    2013-01-01

    Carbonaceous porous materials derived from leather skin residues have been found to have excellent CO2 adsorption properties, with interestingly high gas selectivities for CO2 (α > 200 at a gas composition of 15% CO2/85% N2, 273K, 1 bar) and capacities (>2 mmol·g−1 at 273 K). Both CO2 isotherms and the high heat of adsorption pointed to the presence of strong binding sites for CO2 which may be correlated with both: N content in the leather residues and ultrasmall pore sizes. PMID:28788352

  8. Annotating Protein Functional Residues by Coupling High-Throughput Fitness Profile and Homologous-Structure Analysis

    Directory of Open Access Journals (Sweden)

    Yushen Du

    2016-11-01

    Full Text Available Identification and annotation of functional residues are fundamental questions in protein sequence analysis. Sequence and structure conservation provides valuable information to tackle these questions. It is, however, limited by the incomplete sampling of sequence space in natural evolution. Moreover, proteins often have multiple functions, with overlapping sequences that present challenges to accurate annotation of the exact functions of individual residues by conservation-based methods. Using the influenza A virus PB1 protein as an example, we developed a method to systematically identify and annotate functional residues. We used saturation mutagenesis and high-throughput sequencing to measure the replication capacity of single nucleotide mutations across the entire PB1 protein. After predicting protein stability upon mutations, we identified functional PB1 residues that are essential for viral replication. To further annotate the functional residues important to the canonical or noncanonical functions of viral RNA-dependent RNA polymerase (vRdRp, we performed a homologous-structure analysis with 16 different vRdRp structures. We achieved high sensitivity in annotating the known canonical polymerase functional residues. Moreover, we identified a cluster of noncanonical functional residues located in the loop region of the PB1 β-ribbon. We further demonstrated that these residues were important for PB1 protein nuclear import through the interaction with Ran-binding protein 5. In summary, we developed a systematic and sensitive method to identify and annotate functional residues that are not restrained by sequence conservation. Importantly, this method is generally applicable to other proteins about which homologous-structure information is available.

  9. Major leaching processes of combustion residues - Characterisation, modelling and experimental investigation

    Energy Technology Data Exchange (ETDEWEB)

    Yan Jinying

    1998-12-31

    Characterising leaching behaviour provides ample evidence to identify the major leaching processes of combustion residues. Neutralisation and chemical weathering govern the leaching reactions and control the release of elements from combustion residues, and are thus considered to be the major leaching processes. According to experimental investigations and geochemical simulations, the leaching kinetics of buffering materials are key issues for the understanding of the neutralizing processes. The acid neutralizing capacity at different pH levels depends mainly on the mineralogy of the combustion residues. In combustion residues, the dissolution of glass phases is expected to play an important role in a long-term neutralizing process. The neutralizing process in a flow system is significantly different from that in a batch system. The neutralizing ability of a combustion residue may be strongly affected by solute transport and carbonation reactions in a natural leaching environment. The chemical weathering mainly involves the matrix of combustion residues consisting mostly of glass phases. The dissolution kinetics of waste glass and other possible processes involved in the chemical weathering have been investigated and incorporated into a kinetic reactive transport model. Most important processes in the chemical weathering can be simulated simultaneously using this model. The results show that there is a complicated relationship between the factors controlling the long-term chemical weathering. The environmental impact of the glass dissolution cannot be neglected. Although the glass dissolution provides considerable buffering capacity in long-term weathering, the carbonate is usually a dominant buffering mineral in actual weathering processes. The transformation of carbonate should be considered as an important process in the chemical weathering. The formation of secondary minerals may considerably alter the mineralogy of the waste, and thus change the leaching

  10. Annotating Protein Functional Residues by Coupling High-Throughput Fitness Profile and Homologous-Structure Analysis.

    Science.gov (United States)

    Du, Yushen; Wu, Nicholas C; Jiang, Lin; Zhang, Tianhao; Gong, Danyang; Shu, Sara; Wu, Ting-Ting; Sun, Ren

    2016-11-01

    Identification and annotation of functional residues are fundamental questions in protein sequence analysis. Sequence and structure conservation provides valuable information to tackle these questions. It is, however, limited by the incomplete sampling of sequence space in natural evolution. Moreover, proteins often have multiple functions, with overlapping sequences that present challenges to accurate annotation of the exact functions of individual residues by conservation-based methods. Using the influenza A virus PB1 protein as an example, we developed a method to systematically identify and annotate functional residues. We used saturation mutagenesis and high-throughput sequencing to measure the replication capacity of single nucleotide mutations across the entire PB1 protein. After predicting protein stability upon mutations, we identified functional PB1 residues that are essential for viral replication. To further annotate the functional residues important to the canonical or noncanonical functions of viral RNA-dependent RNA polymerase (vRdRp), we performed a homologous-structure analysis with 16 different vRdRp structures. We achieved high sensitivity in annotating the known canonical polymerase functional residues. Moreover, we identified a cluster of noncanonical functional residues located in the loop region of the PB1 β-ribbon. We further demonstrated that these residues were important for PB1 protein nuclear import through the interaction with Ran-binding protein 5. In summary, we developed a systematic and sensitive method to identify and annotate functional residues that are not restrained by sequence conservation. Importantly, this method is generally applicable to other proteins about which homologous-structure information is available. To fully comprehend the diverse functions of a protein, it is essential to understand the functionality of individual residues. Current methods are highly dependent on evolutionary sequence conservation, which is

  11. Deep residual networks of residual networks for image super-resolution

    Science.gov (United States)

    Wei, Xueqi; Yang, Fumeng; Wu, Congzhong

    2017-11-01

    Single image super-resolution (SISR), which aims at obtaining a high-resolution image from a single low-resolution image, is a classical problem in computer vision. In this paper, we address this problem based on a deep learning method with residual learning in an end-to-end manner. We propose a novel residual-network architecture, Residual networks of Residual networks (RoR), to promote the learning capability of residual networks for SISR. In residual network, the signal can be directly propagated from one unit to any other units in both forward and backward passes when using identity mapping as the skip connections. Based on it, we add level-wise connections upon original residual networks, to dig the optimization ability of residual networks. Our experiments demonstrate the effectiveness and versatility of RoR, it can get a faster convergence speed and gain higher resolution accuracy from considerably increased depth.

  12. Ammonia emission from crop residues : quantification of ammonia volatilization based on crop residue properties

    NARCIS (Netherlands)

    Ruijter, de F.J.; Huijsmans, J.F.M.

    2012-01-01

    This paper gives an overview of available literature data on ammonia volatilization from crop residues. From these data, a relation is derived for the ammonia emission depending on the N-content of crop residue.

  13. Remarks on entanglement assisted classical capacity

    OpenAIRE

    Fan, Heng

    2003-01-01

    The property of the optimal signal ensembles of entanglement assisted channel capacity is studied. A relationship between entanglement assisted channel capacity and one-shot capacity of unassisted channel is obtained. The data processing inequalities, convexity and additivity of the entanglement assisted channel capacity are reformulated by simple methods.

  14. 7 CFR 983.27 - Proprietary capacity.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 8 2010-01-01 2010-01-01 false Proprietary capacity. 983.27 Section 983.27 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing..., ARIZONA, AND NEW MEXICO Definitions § 983.27 Proprietary capacity. Proprietary capacity means the capacity...

  15. Study of the effect of gamma irradiation on phenolic compounds and pesticides residues

    International Nuclear Information System (INIS)

    Fkih, Sana

    2007-01-01

    The aim of this study was to show the effects of this process of conservation on the polyphenol rate and the antioxidant capacity of polyphenols of quince, of the cocoa and those of sage, then to study its effects on the pesticides residues in the sage sheets. The irradiation of quince polyphenols, increased the polyphenols rate as well as the antioxidant capacity. In the case of cocoa polyphenols, we don't have ace observed many differences between the irradiated and not irradiated samples, and in the case of sage polyphenols, the polyphenol rate as well as the antioxidant capacity decreased. Finally, irradiation of parathion caused degradation of this molecule, and the polyphenol rate as well as the antioxidant capacity pf polyphenols of the sheets of sage soaked with parathion was a less decreased than polyphenols of the sheets not soaked with parathion. (Author). 37 refs

  16. Process for measuring residual stresses

    International Nuclear Information System (INIS)

    Elfinger, F.X.; Peiter, A.; Theiner, W.A.; Stuecker, E.

    1982-01-01

    No single process can at present solve all problems. The complete destructive processes only have a limited field of application, as the component cannot be reused. However, they are essential for the basic determination of stress distributions in the field of research and development. Destructive and non-destructive processes are mainly used if investigations have to be carried out on original components. With increasing component size, the part of destructive tests becomes smaller. The main applications are: quality assurance, testing of manufactured parts and characteristics of components. Among the non-destructive test procedures, X-raying has been developed most. It gives residual stresses on the surface and on surface layers near the edges. Further development is desirable - in assessment - in measuring techniques. Ultrasonic and magnetic crack detection processes are at present mainly used in research and development, and also in quality assurance. Because of the variable depth of penetration and the possibility of automation they are gaining in importance. (orig./RW) [de

  17. Prediction of lithium-ion battery capacity with metabolic grey model

    International Nuclear Information System (INIS)

    Chen, Lin; Lin, Weilong; Li, Junzi; Tian, Binbin; Pan, Haihong

    2016-01-01

    Given the popularity of Lithium-ion batteries in EVs (electric vehicles), predicting the capacity quickly and accurately throughout a battery's full life-time is still a challenging issue for ensuring the reliability of EVs. This paper proposes an approach in predicting the varied capacity with discharge cycles based on metabolic grey theory and consider issues from two perspectives: 1) three metabolic grey models will be presented, including MGM (metabolic grey model), MREGM (metabolic Residual-error grey model), and MMREGM (metabolic Markov-residual-error grey model); 2) the universality of these models will be explored under different conditions (such as various discharge rates and temperatures). Furthermore, the research findings in this paper demonstrate the excellent performance of the prediction depending on the three models; however, the precision of the MREGM model is inferior compared to the others. Therefore, we have obtained the conclusion in which the MGM model and the MMREGM model have excellent performances in predicting the capacity under a variety of load conditions, even using few data points for modeling. Also, the universality of the metabolic grey prediction theory is verified by predicting the capacity of batteries under different discharge rates and different temperatures. - Highlights: • The metabolic mechanism is introduced in a grey system for capacity prediction. • Three metabolic grey models are presented and studied. • The universality of these models under different conditions is assessed. • A few data points are required for predicting the capacity with these models.

  18. Outage capacity of multicarrier systems

    KAUST Repository

    Yilmaz, Ferkan

    2010-01-01

    The probability density function and the cumulative distribution function of the product of shifted Gamma variates are obtained in terms of the generalized Fox\\'s H function. Using these new results, the exact outage capacity of multi carrier transmission through a slow Nakagami-m fading channel is presented. Moreover, it is shown that analytical and simulation results are in perfect agreement. © 2009 IEEE.

  19. Tank 12H residuals sample analysis report

    Energy Technology Data Exchange (ETDEWEB)

    Oji, L. N. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Shine, E. P. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Diprete, D. P. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Coleman, C. J. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Hay, M. S. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2015-06-11

    The Savannah River National Laboratory (SRNL) was requested by Savannah River Remediation (SRR) to provide sample preparation and analysis of the Tank 12H final characterization samples to determine the residual tank inventory prior to grouting. Eleven Tank 12H floor and mound residual material samples and three cooling coil scrape samples were collected and delivered to SRNL between May and August of 2014.

  20. Does Bt Corn Really Produce Tougher Residues

    Science.gov (United States)

    Bt corn hybrids produce insecticidal proteins that are derived from a bacterium, Bacillus thuringiensis. There have been concerns that Bt corn hybrids produce residues that are relatively resistant to decomposition. We conducted four experiments that examined the decomposition of corn residues und...

  1. Residual stresses in steel and zirconium weldments

    International Nuclear Information System (INIS)

    Root, J.H.; Coleman, C.E.; Bowden, J.W.

    1997-01-01

    Three-dimensional scans of residual stress within intact weldments provide insight into the consequences of various welding techniques and stress-relieving procedures. The neutron diffraction method for nondestructive evaluation of residual stresses has been applied to a circumferential weld in a ferritic steel pipe of outer diameter 114 mm and thickness 8.6 mm. The maximum tensile stresses, 250 MPa in the hoop direction, are found at mid-thickness of the fusion zone. The residual stresses approach zero within 20 mm from the weld center. The residual stresses caused by welding zirconium alloy components are partially to blame for failures due to delayed-hydride cracking. Neutron diffraction measurements in a GTA-welded Zr-2.5 Nb plate have shown that heat treatment at 530 C for 1 h reduces the longitudinal residual strain by 60%. Neutron diffraction has also been used to scan the residual stresses near circumferential electron beam welds in irradiated and unirradiated Zr-2.5 Nb pressure tubes. The residual stresses due to electron beam welding appear to be lower than 130 MPa, even in the as-welded state. No significant changes occur in the residual stress pattern of the electron-beam welded tube, during a prolonged exposure to thermal neutrons and the temperatures typical of an operating nuclear reactor

  2. Densification of FL Chains via Residuated Frames

    Czech Academy of Sciences Publication Activity Database

    Baldi, Paolo; Terui, K.

    2016-01-01

    Roč. 75, č. 2 (2016), s. 169-195 ISSN 0002-5240 R&D Projects: GA ČR GAP202/10/1826 Keywords : densifiability * standard completeness * residuated lattices * residuated frames * fuzzy logic Subject RIV: BA - General Mathematics Impact factor: 0.625, year: 2016

  3. Spatial resolution enhancement residual coding using hybrid ...

    Indian Academy of Sciences (India)

    a normal video frames possess distinct characteristics compared to a residual frame. In this paper, we .... analyze the characteristics of IP, MC and RE residuals (Kamisli 2010; Rao et al 2007). The estimation ..... Eslami R and Radha H 2007 A new family of nonredundant transforms using hybrid wavelets and directional filter ...

  4. Semantic Tagging with Deep Residual Networks

    NARCIS (Netherlands)

    Bjerva, Johannes; Plank, Barbara; Bos, Johan

    2016-01-01

    We propose a novel semantic tagging task, semtagging, tailored for the purpose of multilingual semantic parsing, and present the first tagger using deep residual networks (ResNets). Our tagger uses both word and character representations and includes a novel residual bypass architecture. We evaluate

  5. Soil water evaporation and crop residues

    Science.gov (United States)

    Crop residues have value when left in the field and also when removed from the field and sold as a commodity. Reducing soil water evaporation (E) is one of the benefits of leaving crop residues in place. E was measured beneath a corn canopy at the soil suface with nearly full coverage by corn stover...

  6. Unicystic ameloblastoma arising from a residual cyst

    Science.gov (United States)

    Mahajan, Amit D; Manjunatha, Bhari Sharanesha; Khurana, Neha M; Shah, Navin

    2014-01-01

    Intraoral swellings involving alveolar ridges in edentulous patients are clinically diagnosed as residual cysts, traumatic bone cysts, Stafne's jaw bone cavity, ameloblastoma and metastatic tumours of the jaw. This case report describes a residual cyst in a 68-year-old edentulous male patient which was enucleated and histopathologically confirmed as a unicystic ameloblastoma. PMID:25199192

  7. Electrodialytic remediation of air pollution control residues

    DEFF Research Database (Denmark)

    Jensen, Pernille Erland

    Air pollution control (APC) residue from municipal solid waste incineration (MSWI) consists of the fly ash, and, in dry and semi-dry systems, also the reaction products from the flue gas cleaning process. APC residue is considered a hazardous waste due to its high alkalinity, high content of salts...

  8. Distribution of residues and primitive roots

    Indian Academy of Sciences (India)

    quadratic residues and non-residues cases using some refinement of van der Warden's the- orem in combinatorial number theory. Therefore, in his proof, the constant p0(N) depends on the van der Warden number, which is very difficult to calculate for all N. For instance, recently, Luca and Thangadurai [8] proved that for all ...

  9. Bioaccumulation and distribution of organochlorine residues across ...

    African Journals Online (AJOL)

    The transfer of organochlorine residues in the food chain and its distribution in the trophic levels was influenced by habitat, environmental conditions, feeding habit and biochemical composition of individual populations. The total residual concentration of OCPs in shellfish and fish ranged between 0.16 ppm and 0.69 ppm.

  10. Power from wastewater and residual products

    DEFF Research Database (Denmark)

    Krogh-Jeppesen, K.

    2007-01-01

    Microbial fuel cells utilise wastewater and residual products from the pretreatment of straw to generate power. Denmark could lead the way......Microbial fuel cells utilise wastewater and residual products from the pretreatment of straw to generate power. Denmark could lead the way...

  11. Residuals Management and Water Pollution Control Planning.

    Science.gov (United States)

    Environmental Protection Agency, Washington, DC. Office of Public Affairs.

    This pamphlet addresses the problems associated with residuals and water quality especially as it relates to the National Water Pollution Control Program. The types of residuals and appropriate management systems are discussed. Additionally, one section is devoted to the role of citizen participation in developing management programs. (CS)

  12. Residuals and the Residual-Based Statistic for Testing Goodness of Fit of Structural Equation Models

    Science.gov (United States)

    Foldnes, Njal; Foss, Tron; Olsson, Ulf Henning

    2012-01-01

    The residuals obtained from fitting a structural equation model are crucial ingredients in obtaining chi-square goodness-of-fit statistics for the model. The authors present a didactic discussion of the residuals, obtaining a geometrical interpretation by recognizing the residuals as the result of oblique projections. This sheds light on the…

  13. 77 FR 24671 - Compliance Guide for Residue Prevention and Agency Testing Policy for Residues

    Science.gov (United States)

    2012-04-25

    ... Food Safety and Inspection Service Compliance Guide for Residue Prevention and Agency Testing Policy for Residues AGENCY: Food Safety and Inspection Service, USDA. ACTION: Notice of availability and... availability of a compliance guide for the prevention of violative residues in livestock slaughter...

  14. Health Reform Requires Policy Capacity

    Directory of Open Access Journals (Sweden)

    Pierre-Gerlier Forest

    2015-05-01

    Full Text Available Among the many reasons that may limit the adoption of promising reform ideas, policy capacity is the least recognized. The concept itself is not widely understood. Although policy capacity is concerned with the gathering of information and the formulation of options for public action in the initial phases of policy consultation and development, it also touches on all stages of the policy process, from the strategic identification of a problem to the actual development of the policy, its formal adoption, its implementation, and even further, its evaluation and continuation or modification. Expertise in the form of policy advice is already widely available in and to public administrations, to well-established professional organizations like medical societies and, of course, to large private-sector organizations with commercial or financial interests in the health sector. We need more health actors to join the fray and move from their traditional position of advocacy to a fuller commitment to the development of policy capacity, with all that it entails in terms of leadership and social responsibility

  15. Residual stress measurement for injection molded components

    Directory of Open Access Journals (Sweden)

    Achyut Adhikari

    2016-07-01

    Full Text Available Residual stress induced during manufacturing of injection molded components such as polymethyl methacrylate (PMMA affects the mechanical and optical properties of these components. These residual stresses can be visualized and quantified by measuring their birefringence. In this paper, a low birefringence polariscope (LBP is used to measure the whole-field residual stress distribution of these injection molded specimens. Detailed analytical and experimental study is conducted to quantify the residual stress measurement in these materials. A commercial birefringence measurement system was used to validate the results obtained to our measurement system. This study can help in material diagnosis for quality and manufacturing purpose and be useful for understanding of residual stress in imaging or other applications.

  16. Residual stresses in zircaloy welds

    International Nuclear Information System (INIS)

    Santisteban, J. R.; Fernandez, L; Vizcaino, P.; Banchik, A.D.; Samper, R; Martinez, R. L; Almer, J; Motta, A.T.; Colas, K.B; Kerr, M.; Daymond, M.R

    2009-01-01

    Welds in Zirconium-based alloys are susceptible to hydrogen embrittlement, as H enters the material due to dissociation of water. The yield strain for hydride cracking has a complex dependence on H concentration, stress state and texture. The large thermal gradients produced by the applied heat; drastically changes the texture of the material in the heat affected zone, enhancing the susceptibility to delayed hydride cracking. Normally hydrides tend to form as platelets that are parallel to the normal direction, but when welding plates, hydride platelets may form on cooling with their planes parallel to the weld and through the thickness of the plates. If, in addition to this there are significant tensile stresses, the susceptibility of the heat affected zone to delayed hydride cracking will be increased. Here we have measured the macroscopic and microscopic residual stressed that appear after PLASMA welding of two 6mm thick Zircaloy-4 plates. The measurements were based on neutron and synchrotron diffraction experiments performed at the Isis Facility, UK, and at Advanced Photon Source, USA, respectively. The experiments allowed assessing the effect of a post-weld heat treatment consisting of a steady increase in temperature from room temperature to 450oC over a period of 4.5 hours; followed by cooling with an equivalent cooling rate. Peak tensile stresses of (175± 10) MPa along the longitudinal direction were found in the as-welded specimen, which were moderately reduced to (150±10) MPa after the heat-treatment. The parent material showed intergranular stresses of (56±4) MPa, which disappeared on entering the heat-affected zone. In-situ experiments during themal cyclong of the material showed that these intergranular stresses result from the anisotropy of the thermal expansion coefficient of the hexagonal crystal lattice. [es

  17. Residual complaints after neuralgic amyotrophy.

    Science.gov (United States)

    Cup, Edith H; Ijspeert, Jos; Janssen, Renske J; Bussemaker-Beumer, Chaska; Jacobs, Joost; Pieterse, Allan J; van der Linde, Harmen; van Alfen, Nens

    2013-01-01

    To develop recommendations regarding outcome measures and topics to be addressed in rehabilitation for persons with neuralgic amyotrophy (NA), this study explored which functions and activities are related to persisting pain in NA and which questionnaires best capture these factors. A questionnaire-based survey from 2 cross-sectional cohorts, one of patients visiting the neurology outpatient clinic and a cohort seen at a multidisciplinary plexus clinic. Two tertiary referral clinics based in the Department of Neurology and Rehabilitation from a university medical center provided the data. A referred sample of patients (N=248) with either idiopathic or hereditary NA who fulfilled the criteria for this disorder, in whom the last episode of NA had been at least 6 months ago and included brachial plexus involvement. Not applicable. Two custom clinical screening questionnaires were used as well as the Shoulder Rating Questionnaire-Dutch Language Version, the Shoulder Pain and Disability Index (SPADI), the Shoulder Disability Questionnaire (SDQ), and Overall Disability Sum Score. The survey confirms the high prevalence of persisting pain and impairments. More than half of the patients were restricted by pain, while in those without pain 60% experienced residual paresis. Correlations show an intimate relation between pain, scapular instability, problems with overhead activities, and increased fatigability. A standard physical therapy approach was ineffective or aggravated symptoms in more than 50%. Pain and fatigue are strongly correlated to persisting scapular instability and increased fatigability of the affected muscles in NA. Our results suggest that an integrated rehabilitation approach is needed in which all of these factors are addressed. We further recommend using the SPADI and SDQ in future studies to evaluate the natural course and treatment effects in NA. Copyright © 2013 American Congress of Rehabilitation Medicine. Published by Elsevier Inc. All rights

  18. Residual DPCM about Motion Compensated Residual Signal for H.264 Lossless Coding

    Science.gov (United States)

    Han, Ki-Hun; Rao, Kamisetty R.; Lee, Yung-Lyul

    In this letter, a new Inter lossless coding method based on a residual DPCM (Differential Pulse Code Modulation) is proposed to improve compression ratio in the H.264 standard. Since the spatial correlation in a residual block can be further exploited among the residual signals after motion estimation/compensation, horizontal or vertical DPCM in the residual signals can be applied to further reduce the magnitudes of the residual signals. The proposed method reduces the average bitrates of 3.5% compared with the Inter lossless coding of the H.264 standard.

  19. Novel feature for catalytic protein residues reflecting interactions with other residues.

    Directory of Open Access Journals (Sweden)

    Yizhou Li

    Full Text Available Owing to their potential for systematic analysis, complex networks have been widely used in proteomics. Representing a protein structure as a topology network provides novel insight into understanding protein folding mechanisms, stability and function. Here, we develop a new feature to reveal correlations between residues using a protein structure network. In an original attempt to quantify the effects of several key residues on catalytic residues, a power function was used to model interactions between residues. The results indicate that focusing on a few residues is a feasible approach to identifying catalytic residues. The spatial environment surrounding a catalytic residue was analyzed in a layered manner. We present evidence that correlation between residues is related to their distance apart most environmental parameters of the outer layer make a smaller contribution to prediction and ii catalytic residues tend to be located near key positions in enzyme folds. Feature analysis revealed satisfactory performance for our features, which were combined with several conventional features in a prediction model for catalytic residues using a comprehensive data set from the Catalytic Site Atlas. Values of 88.6 for sensitivity and 88.4 for specificity were obtained by 10-fold cross-validation. These results suggest that these features reveal the mutual dependence of residues and are promising for further study of structure-function relationship.

  20. Occurrence of non extractable pesticide residues in physical and chemical fractions of two soils

    Science.gov (United States)

    Andreou, Kostas; Semple, Kirk; Jones, Kevin

    2010-05-01

    Soils are considered to be a significant sink for organic contaminants, including pesticides, in the environment. Understanding the distribution and localisation of aged pesticide residues in soil is of great importance for assessing the mobility and availability of these chemicals in the environment. This study aimed to characterise the distribution of radiolabeled herbicide isoproturon and the radiolabeled insecticides diazinon and cypermethrin in two organically managed soils. The soils were spiked and aged under laboratory conditions for 17 months. The labile fraction of the pesticides residues was recovered in CaCl2 (0.01M) and then subjected to physical size fractionation using sedimentation and centrifugation steps, with >20μm, 20-2μm and 2-0.1μm soil factions collected. Further, the distribution of the pesticide residues in the organic matter of the fractionated soil was investigated using a sequential alkaline extraction (0.1N NaOH) into humic and fulvic acid and humin. Soil fractions of 20-2μm and 2-0.1μm had the largest burden of the 14C-residues. Different soil constituents have different capacities to form non-extractable residues. Soil solid fractions of 20-2 µm and 20 µm). Fulvic acid showed to play a vital role in the formation and stabilisation of non-extractable 14C-pesticide residues in most cases.Assessment of the likelihood of the pesticide residues to become available to soil biota requires an understanding of the structure of the SOM matrix and the definition of the kinetics of the pesticide residues in different SOM pools as a function of the time.

  1. USAGE OF ALGAE SPECIES CHAETOMORPHA GRACILIS AND CH. AEREA FOR DEPURATION PROCESS OF THE RESIDUAL WATERS

    Directory of Open Access Journals (Sweden)

    SALARU VICTOR

    2008-11-01

    Full Text Available Rapid increase of the population on the globe scale imposes maximum exploration of the natural resources and first of all of the aquatic resources. As a result are obtained an enormous quantity of residual waters which pollute the waters from rivers, lakes, freatic and underground waters. Elaboration of the depuration methods for residual waters the quantity of which grows continuously, is one of the most up to dated issue of the world. The physical-chemical depuration methods of the residual waters are very expensive and lack the efficiency we would like to have. The most efficient method proved to be the biological method using some species of algae and superior aquatic plants. In our experiences we have involved filamentous green algae Chaetomorpha gracilis and Ch. aerea for depuration of the sewerage water from town Cimishlia. The concentration of the mineral nitrogen compounds in the residual water is around 92,5 mg/l, and of the phosphates 10,1 mg/l. There were used the following concentration of the sewerage water: 10%, 25% and 50%. The most intense development of algae Chaetomorpha aerea was observed in the variant with 10% of residual water, in which the total concentration of the nitrogen was 10,24 mg/l, and of the phosphates 1,05 mg/l. For this variant the depuration water level was about 56,9%. For the case with Chaetomorpha gracilis, the depuration level for the same concentration of the residual water constituted 55,9 %. Increase of the concentration of the polluted water inhibits development of the algae reducing to the minimum their capacity to assimilate the nitrogen and the phosphor. In the solutions with 50 % of residual waters, the algae didn't die, but at the same time they didn't develop. From this results that both algae may be used in the phytoamelioration of the residual waters being diluted at 10% with purified water.

  2. Analysis of residual swirl in tangentially-fired natural gas-boiler

    International Nuclear Information System (INIS)

    Hasril Hasini; Muhammad Azlan Muad; Mohd Zamri Yusoff; Norshah Hafeez Shuaib

    2010-01-01

    This paper describes the investigation on residual swirl flow in a 120 MW natural gas, full-scale, tangential-fired boiler. Emphasis is given towards the understanding of the behavior of the combustion gas flow pattern and temperature distribution as a result of the tangential firing system of the boiler. The analysis was carried out based on three-dimensional computational modeling on full scale boiler with validation from key design parameter as well as practical observation. Actual operating parameters of the actual boiler are taken as the boundary conditions for this modeling. The prediction of total heat flux was found to be in agreement with the key design parameter while the residual swirl predicted at the upper furnace agrees qualitatively with the practical observation. Based on this comparison, detail analysis was carried out for comprehensive understanding on the generation and destruction of the residual swirl behavior in boiler especially those with high capacity. (author)

  3. TNTM85 and TNTM81 transports / storage flasks: An optimized solution for vitrified residues

    International Nuclear Information System (INIS)

    Sicard, D.; Verdier, A.; Dyck, P.

    2006-01-01

    By analyzing the evolution of burnup of spent fuel to be reprocessed, the high activity vitrified residues would not be transported in the existing flask designs. Therefore COGEMA LOGISTICS decided in the late nineties to develop a design with optimized capacity able to store and transport the most active and hottest canisters. The TN TM 85 flask shall permit in the near future in Germany the storage and the transport of the highest vitrified residues defining a thermal power of 56 kW. The challenge for the TN TM 85 flask design was that the geometry entry data were very restrictive and were combined with a fairly wide range set by COGEMA Specification 300AQ16 relative to vitrified residue canister. In addition, the cask had to fit as much as possible in the existing procedures for the TN TM 28 cask and TS 28 V cask, all along the logistics chain of loading, unloading, transport and maintenance. (authors)

  4. Prediction of machining induced residual stresses

    Science.gov (United States)

    Pramod, Monangi; Reddy, Yarkareddy Gopi; Prakash Marimuthu, K.

    2017-07-01

    Whenever a component is machined, residual stresses are induced in it. These residual stresses induced in the component reduce its fatigue life, corrosion resistance and wear resistance. Thus it is important to predict and control the machining-induced residual stress. A lot of research is being carried out in this area in the past decade. This paper aims at prediction of residual stresses during machining of Ti-6Al-4V. A model was developed and under various combinations of cutting conditions such as, speed, feed and depth of cut, the behavior of residual stresses were simulated using Finite Element Model. The present work deals with the development of thermo-mechanical model to predict the machining induced residual stresses in Titanium alloy. The simulation results are compared with the published results. The results are in good agreement with the published results. Future work involves optimization or the cutting parameters that effect the machining induced residual stresses. The results obtained were validated with previous work.

  5. Residual stress field of ballised holes

    International Nuclear Information System (INIS)

    Lai, Man On; He, Zhimin

    2012-01-01

    Ballising, involving pushing a slightly over-sized ball made of hard material through a hole, is a kind of cold working process. Applying ballising process to fastener holes produces compressive residual stress on the edge of the holes, and therefore increases the fatigue life of the components or structures. Quantification of the residual stress field is critical to define and precede the ballising process. In this article, the ballised holes are modeled as cold-expanded holes. Elastic-perfectly plastic theory is employed to analyze the holes with cold expansion process. For theoretical simplification, an axially symmetrical thin plate with a cold expanded hole is assumed. The elasticplastic boundaries and residual stress distribution surrounding the cold expanded hole are derived. With the analysis, the residual stress field can be obtained together with actual cold expansion process in which only the diameters of hole before and after cold expansion need to be measured. As it is a non-destructive method, it provides a convenient way to estimate the elastic-plastic boundaries and residual stresses of cold worked holes. The approach is later extended to the case involving two cold-worked holes. A ballised hole is looked upon as a cold expanded hole and therefore is investigated by the approach. Specimens ballised with different interference levels are investigated. The effects of interference levels and specimen size on residual stresses are studied. The overall residual stresses of plates with two ballised holes are obtained by superposing the residual stresses induced on a single ballised hole. The effects of distance between the centers of the two holes with different interference levels on the residual stress field are revealed

  6. Measuring melting capacity with calorimetry

    OpenAIRE

    Betten, Linda

    2014-01-01

    Road salting is an important aspect of winter maintenance. There has been an increase in the usage of salt in later years to keep the road safe and accessible. It is a desire to reduce the amount of salt due to environmental aspects. To achieve better practices for winter maintenance it is necessary to obtain more knowledge about the different properties of salt. The motivation for this thesis is to develop a better method for determining the melting capacity for salt, which is an important p...

  7. Valorization Challenges to Almond Residues: Phytochemical Composition and Functional Application

    Directory of Open Access Journals (Sweden)

    Iva Prgomet

    2017-10-01

    Full Text Available Almond is characterized by its high nutritional value; although information reported so far mainly concerns edible kernel. Even though the nutritional and commercial relevance of the almond is restricted to almond meat; to date; increasing attention has been paid to other parts of this fruit (skin; shell; and hull; considered by-products that are scarcely characterized and exploited regarding their properties as valuable sources of bioactive compounds (mainly represented by phenolic acids and flavonoids. This lack of proper valorization procedures entails the continuation of the application of traditional procedures to almond residues that nowadays are mainly addressed to livestock feed and energy production. In this sense; data available on the physicochemical and phytochemical composition of almond meat and its related residues suggest promising applications; and allow one to envisage new uses as functional ingredients towards value-added foods and feeds; as well as a source of bioactive phytochemicals to be included in cosmetic formulations. This objective has prompted investigators working in the field to evaluate their functional properties and biological activity. This approach has provided interesting information concerning the capacity of polyphenolic extracts of almond by-products to prevent degenerative diseases linked to oxidative stress and inflammation in human tissues and cells; in the frame of diverse pathophysiological situations. Hence; this review deals with gathering data available in the scientific literature on the phytochemical composition and bioactivity of almond by-products as well as on their bioactivity so as to promote their functional application.

  8. Principles of the measurement of residual stress by neutron diffraction

    Energy Technology Data Exchange (ETDEWEB)

    Webster, G.A.; Ezeilo, A.N. [Imperial Coll. of Science and Technology, London (United Kingdom). Dept. of Mechanical Engineering

    1996-11-01

    The presence of residual stresses in engineering components can significantly affect their load carrying capacity and resistance to fracture. In order to quantify their effect it is necessary to know their magnitude and distribution. Neutron diffraction is the most suitable method of obtaining these stresses non-destructively in the interior of components. In this paper the principles of the technique are described. A monochromatic beam of neutrons, or time of flight measurements, can be employed. In each case, components of strain are determined directly from changes in the lattice spacings between crystals. Residual stresses can then be calculated from these strains. The experimental procedures for making the measurements are described and precautions for achieving reliable results discussed. These include choice of crystal planes on which to make measurements, extent of masking needed to identify a suitable sampling volume, type of detector and alignment procedure. Methods of achieving a stress free reference are also considered. A selection of practical examples is included to demonstrate the success of the technique. (author) 14 figs., 1 tab., 18 refs.

  9. Principles of the measurement of residual stress by neutron diffraction

    International Nuclear Information System (INIS)

    Webster, G.A.; Ezeilo, A.N.

    1996-01-01

    The presence of residual stresses in engineering components can significantly affect their load carrying capacity and resistance to fracture. In order to quantify their effect it is necessary to know their magnitude and distribution. Neutron diffraction is the most suitable method of obtaining these stresses non-destructively in the interior of components. In this paper the principles of the technique are described. A monochromatic beam of neutrons, or time of flight measurements, can be employed. In each case, components of strain are determined directly from changes in the lattice spacings between crystals. Residual stresses can then be calculated from these strains. The experimental procedures for making the measurements are described and precautions for achieving reliable results discussed. These include choice of crystal planes on which to make measurements, extent of masking needed to identify a suitable sampling volume, type of detector and alignment procedure. Methods of achieving a stress free reference are also considered. A selection of practical examples is included to demonstrate the success of the technique. (author) 14 figs., 1 tab., 18 refs

  10. Experiences on Pretreatment and Pelletizing of Forestry Residues in Spain

    Energy Technology Data Exchange (ETDEWEB)

    Ortiz, L. [Univ. of Vigo (Spain). Dept. of Natural Resources and Environment

    2006-07-15

    The aim of this work is to assess the technical possibilities in order to use typical wastes from the Spanish forests so that to produce high quality Pellets as well as to study the technical problems in some specific by-products. One of the main barriers the Spanish market faces in order to consolidate the pelletizing technologies is the fact that there are very few industrial experiences of massive production using forestry residues biomass. Instead, industrial wastes such as sawdust and shavings have been more commonly used, to-day. To that purpose, a series of experiences on pretreatment and pelletizing of forestry residues are shown in this work, using to that end typical biomass forestry residues from the Mediterranean countries and making forced-drying studies, granulometric reduction and densifying experiences for the very first time in Spain. The engineering data were obtained from experiences with a trommel type dryer of about 1,000 Kg/h using pine wastes (P. pinaster), eucalyptus (Eucalyptus globulus) and furze (Ulex europeaeus) as a raw material. Besides, the consumption in chipping and milling from wastes obtained from different parts of trees such as coniferous bark, branches, etc., are also analyzed, using to that end a pilot plant about 200 Kg/h. Finally, studies on pelletizing in a plant of 2,500 Kg/h capacity have been carried out. These in-depth studies try to determine the perspectives for forestry biomass management. Likewise, we also aim at pinning down the limits in using hard materials like the eucalyptus bark, as well as to grasp the potential of this type of wastes that have not been used in Spain yet.

  11. Guidelines for selection and presentation of residue values of pesticides

    NARCIS (Netherlands)

    Velde-Koerts T van der; Hoeven-Arentzen PH van; Ossendorp BC; RIVM-SIR

    2004-01-01

    Pesticide residue assessments are executed to establish legal limits, called Maximum Residue Limits (MRLs). MRLs are derived from the results of these pesticide residue trials, which are performed according to critical Good Agricultural Practice. Only one residue value per residue trial may be

  12. RESIDUAL RISK ASSESSMENT: GAS DISTRIBUTION STAGE ...

    Science.gov (United States)

    This document describes the residual risk assessment for the Gas Distribution Stage 1 souce category. For stationary sources, section 112 (f) of the Clean Air Act requires EPA to assess risks to human health and the environment following implementation of technology-based control standards. If these technology-based control standards do not provide an ample margin of safety, then EPA is required to promulgate addtional standards. This document describes the methodology and results of the residual risk assessment performed for the Gas Distribution Stage 1 source category. The results of this analyiss will assist EPA in determining whether a residual risk rule for this source category is appropriate.

  13. Properties of residuals for spatial point processes

    DEFF Research Database (Denmark)

    Baddeley, A.; Møller, Jesper; Pakes, A. G.

    2008-01-01

    For any point process in Rd that has a Papangelou conditional intensity λ, we define a random measure of ‘innovations' which has mean zero. When the point process model parameters are estimated from data, there is an analogous random measure of ‘residuals'. We analyse properties of the innovation...... and residuals, including first and second moments, conditional independence, a martingale property, and lack of correlation. Some large sample asymptotics are studied. We derive the marginal distribution of smoothed residuals by solving a distributional equivalence....

  14. Mapping Residual Structure in Intrinsically Disordered Proteins at Residue Resolution Using Millisecond Hydrogen/Deuterium Exchange and Residue Averaging

    Science.gov (United States)

    Keppel, Theodore R.; Weis, David D.

    2015-04-01

    Measurement of residual structure in intrinsically disordered proteins can provide insights into the mechanisms by which such proteins undergo coupled binding and folding. The present work describes an approach to measure residual structure in disordered proteins using millisecond hydrogen/deuterium (H/D) exchange in a conventional bottom-up peptide-based workflow. We used the exchange mid-point, relative to a totally deuterated control, to quantify the rate of H/D exchange in each peptide. A weighted residue-by-residue average of these midpoints was used to map the extent of residual structure at near single-residue resolution. We validated this approach both by simulating a disordered protein and experimentally using the p300 binding domain of ACTR, a model disordered protein already well-characterized by other approaches. Secondary structure elements mapped in the present work are in good agreement with prior nuclear magnetic resonance measurements. The new approach was somewhat limited by a loss of spatial resolution and subject to artifacts because of heterogeneities in intrinsic exchange. Approaches to correct these limitations are discussed.

  15. UN OPEN GIS CAPACITY BUILDING

    Directory of Open Access Journals (Sweden)

    A. Albertella

    2017-07-01

    Full Text Available The UN Open GIS Initiative is to identify and develop, under UN guidance, an Open Source GIS bundle that meets the requirements of UN operations, taking full advantage of the expertise of mission partners (partner nations, technology contributing countries, international organizations, academia, NGO’s, private sector. The project, started in 2016, is composed by 4 working groups. One of the working group is specifically related to Capacity Building, given its importance for the success of the project. UN Open GIS will be based on some existing open source geospatial software (packages and libraries with many extensions specifically developed. The users of the platform will be the UN staff supporting with mapping and GIS the peacekeeping missions. Therefore, they are generally expert of this specific domain, even if they are currently using proprietary software. UN Open GIS Capacity Building is specifically thought for covering this gap, providing them the suitable background about open source geospatial software in general and the education tailored to the solution that has been being developed within the project itself.

  16. World nuclear power plant capacity

    International Nuclear Information System (INIS)

    1991-01-01

    This report provides the background information for statistics and analysis developed by NUKEM in its monthly Market Report on the Nuclear Fuel Cycle. The assessments in this Special Report are based on the continuous review of individual nuclear power plant projects. This Special Report begins with tables summarizing a variety of nuclear power generating capacity statistics for 1990. It continues with a brief review of the year's major events regarding each country's nuclear power program. The standard NUKEM Market Report tables on nuclear plant capacity are given on pages 24 and 25. Owing to space limitations, the first year shown is 1988. Please refer to previous Special Reports for data covering earlier years. Detailed tables for each country list all existing plants as well as those expected by NUKEM to be in commercial operation by the end of 2005. An Appendix containing a list of abbreviations can be found starting on page 56. Only nuclear power plants intended for civilian use are included in this Special Report. Reactor lifetimes are assumed to be 35 years for all light water reactors and 30 years for all other reactor types, unless other data or definite decommissioning dates have been published by the operators. (orig./UA) [de

  17. Progression of emphysema in a 12-month hyperpolarized 3He-MRI study: lacunarity analysis provided a more sensitive measure than standard ADC analysis

    DEFF Research Database (Denmark)

    Diaz, Sandra; Casselbrant, Ingrid; Piitulainen, Eeva

    2009-01-01

    RATIONALE AND OBJECTIVES: Inhaled hyperpolarized (3)He magnetic resonance (MR) imaging has been used to measure alveolar size in patients with emphysema. The aim of this study was to test the hypothesis that (3)He MR images could be used to develop a biomarker of emphysema progression. MATERIALS...... AND METHODS: Twelve healthy controls and 18 patients with emphysema (eight current smokers, 10 ex-smokers) were imaged at baseline and 6 and 12 months. An additional nine subjects with alpha-1 antitrypsin deficiency (four with emphysema, six without symptoms) were also imaged at baseline and at 6 months. Each...... subject was imaged at two lung volumes: functional residual capacity (FRC) and FRC plus 15% of total lung capacity. Means and standard deviations of apparent diffusion coefficients (ADCs) were calculated from coronal images of the entire lung and correlated with pulmonary function test results...

  18. Estimation of railroad capacity using parametric methods.

    Science.gov (United States)

    2013-12-01

    This paper reviews different methodologies used for railroad capacity estimation and presents a user-friendly method to measure capacity. The objective of this paper is to use multivariate regression analysis to develop a continuous relation of the d...

  19. Outlet diffusers to increase culvert capacity.

    Science.gov (United States)

    2016-06-01

    Aging infrastructure and changing weather patterns present the need to increase the capacity of existing highway culverts. This research approaches this challenge through the use of diffuser outlet systems to increase pipe capacity and reduce outlet ...

  20. Efficient particle filtering through residual nudging

    KAUST Repository

    Luo, Xiaodong

    2013-05-15

    We introduce an auxiliary technique, called residual nudging, to the particle filter to enhance its performance in cases where it performs poorly. The main idea of residual nudging is to monitor and, if necessary, adjust the residual norm of a state estimate in the observation space so that it does not exceed a pre-specified threshold. We suggest a rule to choose the pre-specified threshold, and construct a state estimate accordingly to achieve this objective. Numerical experiments suggest that introducing residual nudging to a particle filter may (substantially) improve its performance, in terms of filter accuracy and/or stability against divergence, especially when the particle filter is implemented with a relatively small number of particles. © 2013 Royal Meteorological Society.

  1. Surgical treatment for residual or recurrent strabismus

    Directory of Open Access Journals (Sweden)

    Tao Wang

    2014-12-01

    Full Text Available Although the surgical treatment is a relatively effective and predictable method for correcting residual or recurrent strabismus, such as posterior fixation sutures, medial rectus marginal myotomy, unilateral or bilateral rectus re-recession and resection, unilateral lateral rectus recession and adjustable suture, no standard protocol is established for the surgical style. Different surgical approaches have been recommended for correcting residual or recurrent strabismus. The choice of the surgical procedure depends on the former operation pattern and the surgical dosages applied on the patients, residual or recurrent angle of deviation and the operator''s preference and experience. This review attempts to outline recent publications and current opinion in the management of residual or recurrent esotropia and exotropia.

  2. Earthworm tolerance to residual agricultural pesticide contamination

    DEFF Research Database (Denmark)

    Givaudan, Nicolas; Binet, Françoise; Le Bot, Barbara

    2014-01-01

    This study investigates if acclimatization to residual pesticide contamination in agricultural soils is reflected in detoxification, antioxidant enzyme activities and energy budget of earthworms. Five fields within a joint agricultural area exhibited different chemical and farming histories from...

  3. Cyolane residues in milk of lactating goats

    International Nuclear Information System (INIS)

    Zayed, S.M.A.D.; Osman, A.; Fakhr, I.M.I.

    1981-01-01

    Consecutive feeding of lactating goats with 14 C-alkyl labelled cyolane for 5 days at dietary levels 8 and 16 ppm resulted in the appearance of measurable insecticide residues in milk (0.02-0.04 mg/kg). The residue levels were markedly reduced after a withdrawal period of 7 days. Analysis of urine and milk residues showed the presence of similar metabolites in addition to the parent compound. The major part of the residue consisted of mono-, diethyl phosphate and 2 hydrophilic unknown metabolites. The erythrocyte cholinesterase activity was reduced to about 50% after 24 hours whereas the plasma enzyme was only slightly affected. The animals remained symptom-free during the experimental period. (author)

  4. FINITE ELEMENT MODEL FOR PREDICTING RESIDUAL ...

    African Journals Online (AJOL)

    direction (σx) had a maximum value of 375MPa (tensile) and minimum value of ... These results shows that the residual stresses obtained by prediction from the finite element method are in fair agreement with the experimental results.

  5. Functional scintigraphy of pulmonary ventilation with 133Xe in juvenile scoliosis

    International Nuclear Information System (INIS)

    Grau, M.; Leisner, B.; Rohloff, R.; Fink, U.; Moser, E.; Matzen, K.A.; Haeusinger, K.; Muenchen Univ.; Muenchen Univ.

    1981-01-01

    Twenty children with severe scoliosis underwent spirometry, chest X-ray and 133 Xe ventilation studies before surgical correction by the Harrington operation. By means of functional scintigraphy the relative distribution of the functional residual capacity (FRC) and the wash-out curves (3 min-retention without background correction, mean time constant, effectivity index after background correction) were analysed quantitatively. The chest X-ray and the single-breath-phase of the ventilation study remained mostly unchanged, whereas the shifting of the FRC distribution towards the lung of the concave side indicated in all cases a regional ventilation restriction of the convex side. In addition the analysis of the wash-out curves showed a regional impairment of the alveolar ventilation of the convex side which exceeded the shifting of FRC distribution. Even in the cases with normal spirometric values all scintigraphic parameters were slightly pathological, probably due to the decreased lung function caused by the scoliosis. The effectivity index taking into account the respiration frequency, the tidal volume, the FRC and the dead space, was found to be the most accurate and sensitive parameter for the evaluation of regional ventilation impairment. (orig.) [de

  6. Relationship of end-expiratory pressure, lung volume, and /sup 99m/Tc-DTPA clearance

    International Nuclear Information System (INIS)

    Cooper, J.A.; van der Zee, H.; Line, B.R.; Malik, A.B.

    1987-01-01

    We investigated the dose-response effect of positive end-expiratory pressure (PEEP) and increased lung volume on the pulmonary clearance rate of aerosolized technetium-99m-labeled diethylenetriaminepentaacetic acid (99mTc-DTPA). Clearance of lung radioactivity was expressed as percent decrease per minute. Base-line clearance was measured while anesthetized sheep (n = 20) were ventilated with 0 cmH 2 O end-expiratory pressure. Clearance was remeasured during ventilation at 2.5, 5, 10, 15, or 20 cmH 2 O PEEP. Further studies showed stepwise increases in functional residual capacity (FRC) (P less than 0.05) measured at 0, 2.5, 5, 10, 15, and 20 cmH 2 O PEEP. At 2.5 cmH 2 O PEEP, the clearance rate was not different from that at base line (P less than 0.05), although FRC was increased from base line. Clearance rate increased progressively with increasing PEEP at 5, 10, and 15 cmH 2 O (P less than 0.05). Between 15 and 20 cmH 2 O PEEP, clearance rate was again unchanged, despite an increase in FRC. The pulmonary clearance of aerosolized /sup 99m/Tc-DTPA shows a sigmoidal response to increasing FRC and PEEP, having both threshold and maximal effects. This relationship is most consistent with the hypothesis that alveolar epithelial permeability is increased by lung inflation

  7. Neutron diffraction residual strain / stress measurements

    International Nuclear Information System (INIS)

    Paradowska, Anna

    2012-01-01

    Residual stresses affect mechancial properties of materials and prodcuts, it is essential to estimate them practically in order to esatblish acceptable limits. Knowledge of the development of residual stresses in components at the various production stages- extrusion, rolling, machining, welding and heat treating-can be used to imporve product reliability and performance. This short article gives an example relevant to the power industry using ANSTO's 'Kowari' neutron strain scanner.

  8. Nitrogen mineralization from organic residues: research opportunities.

    Science.gov (United States)

    Cabrera, M L; Kissel, D E; Vigil, M F

    2005-01-01

    Research on nitrogen (N) mineralization from organic residues is important to understand N cycling in soils. Here we review research on factors controlling net N mineralization as well as research on laboratory and field modeling efforts, with the objective of highlighting areas with opportunities for additional research. Among the factors controlling net N mineralization are organic composition of the residue, soil temperature and water content, drying and rewetting events, and soil characteristics. Because C to N ratio of the residue cannot explain all the variability observed in N mineralization among residues, considerable effort has been dedicated to the identification of specific compounds that play critical roles in N mineralization. Spectroscopic techniques are promising tools to further identify these compounds. Many studies have evaluated the effect of temperature and soil water content on N mineralization, but most have concentrated on mineralization from soil organic matter, not from organic residues. Additional work should be conducted with different organic residues, paying particular attention to the interaction between soil temperature and water content. One- and two-pool exponential models have been used to model N mineralization under laboratory conditions, but some drawbacks make it difficult to identify definite pools of mineralizable N. Fixing rate constants has been used as a way to eliminate some of these drawbacks when modeling N mineralization from soil organic matter, and may be useful for modeling N mineralization from organic residues. Additional work with more complex simulation models is needed to simulate both gross N mineralization and immobilization to better estimate net N mineralized from organic residues.

  9. Disposal of radioactive residuals requires careful planning

    International Nuclear Information System (INIS)

    Pontius, F.W.

    1994-01-01

    Radionuclides removed from source waters during water treatment become concentrated in residual liquids and sludges. Treatment technologies used to remove these contaminants from source waters may generate wastes that contain substantial radioactivity. Water systems that install one or more of these technologies in order to comply with the maximum contaminant levels (MCLs) eventually adopted must dispose of the residuals. Disposal of radionuclide-containing wastes can be especially difficult, depending on the nature and amount of radioactivity present

  10. Plutonium fuel fabrication residues and wastes

    International Nuclear Information System (INIS)

    Arnal, T.; Cousinou, G.; Desille, H.

    1982-04-01

    This paper discusses the current situation in the fabrication plant at Cadarache with an annual plutonium throughput of several tons. Three major fabrication byproduct categories are defined in this plant: 1) scraps, directly recycled at the fabrication input station; 2) residues, byproducts recycled by chemical processes, or processed in washing and incineration stations; 3) wastes, placed in drums and evacuated directly to a waste conditioning station. The borderline between residues and wastes has yet to be precisely determined

  11. Protein structure based prediction of catalytic residues

    Science.gov (United States)

    2013-01-01

    Background Worldwide structural genomics projects continue to release new protein structures at an unprecedented pace, so far nearly 6000, but only about 60% of these proteins have any sort of functional annotation. Results We explored a range of features that can be used for the prediction of functional residues given a known three-dimensional structure. These features include various centrality measures of nodes in graphs of interacting residues: closeness, betweenness and page-rank centrality. We also analyzed the distance of functional amino acids to the general center of mass (GCM) of the structure, relative solvent accessibility (RSA), and the use of relative entropy as a measure of sequence conservation. From the selected features, neural networks were trained to identify catalytic residues. We found that using distance to the GCM together with amino acid type provide a good discriminant function, when combined independently with sequence conservation. Using an independent test set of 29 annotated protein structures, the method returned 411 of the initial 9262 residues as the most likely to be involved in function. The output 411 residues contain 70 of the annotated 111 catalytic residues. This represents an approximately 14-fold enrichment of catalytic residues on the entire input set (corresponding to a sensitivity of 63% and a precision of 17%), a performance competitive with that of other state-of-the-art methods. Conclusions We found that several of the graph based measures utilize the same underlying feature of protein structures, which can be simply and more effectively captured with the distance to GCM definition. This also has the added the advantage of simplicity and easy implementation. Meanwhile sequence conservation remains by far the most influential feature in identifying functional residues. We also found that due the rapid changes in size and composition of sequence databases, conservation calculations must be recalibrated for specific

  12. Residual stress measurement at Budapest Neutron Center

    International Nuclear Information System (INIS)

    Gyula, T.

    2005-01-01

    The use of residual stress measurements of different construction element and recent possibilities of Budapest Neutron Centre are presented. The details investigated already: gas turbine wheel, axial compressor blade, turbine blade and plastically deformed stainless steel. We demonstrated the use of a neutron scattering (SANS, residual stress, diffraction) for the materials behavior investigation in order to analyze the processes going on under the different mechanical loading. The direction of possible instrumental development is presented. (author)

  13. Light water reactor capacity factor investigation

    International Nuclear Information System (INIS)

    Meachum, T.R.; Monnie, D.I.; Whitacre, R.F. Jr.

    1985-01-01

    One of the internationally accepted measurements of an electrical generating station's productivity is the capacity factor. Comparison of the United States domestic nuclear facilities' cumulative capacity factors to the world shows that the US, while leading the western world in number of operating nuclear facilities, is near the bottom in the overall cumulative capacity factor. The purpose of this report is to identify the institutional and technological factors, which both adversely and favorably affect the domestic nuclear utilities' cumulative capacity factors

  14. Why Are We Talking About Capacity Markets?

    Energy Technology Data Exchange (ETDEWEB)

    Frew, Bethany

    2017-06-28

    Revenue sufficiency or 'missing money' concerns in wholesale electricity markets are important because they could lead to resource (or capacity) adequacy shortfalls. Capacity markets or other capacity-based payments are among the proposed solutions to remedy these challenges. This presentation provides a high-level overview of the importance of and process for ensuring resource adequacy, and then discusses considerations for capacity markets under futures with high penetrations of variable resources such as wind and solar.

  15. Removal of coagulant aluminum from water treatment residuals by acid.

    Science.gov (United States)

    Okuda, Tetsuji; Nishijima, Wataru; Sugimoto, Mayo; Saka, Naoyuki; Nakai, Satoshi; Tanabe, Kazuyasu; Ito, Junki; Takenaka, Kenji; Okada, Mitsumasa

    2014-09-01

    Sediment sludge during coagulation and sedimentation in drinking water treatment is called "water treatment residuals (WTR)". Polyaluminum chloride (PAC) is mainly used as a coagulant in Japan. The recycling of WTR has been desired; one method for its reuse is as plowed soil. However, WTR reuse in this way is inhibited by the aluminum from the added PAC, because of its high adsorption capacity for phosphate and other fertilizer components. The removal of such aluminum from WTR would therefore be advantageous for its reuse as plowed soil; this research clarified the effect of acid washing on aluminum removal from WTR and on plant growth in the treated soil. The percentage of aluminum removal from raw WTR by sulphuric acid solution was around 90% at pH 3, the percentage decreasing to 40% in the case of a sun-dried sample. The maximum phosphate adsorption capacity was decreased and the available phosphorus was increased by acid washing, with 90% of aluminum removal. The enhancement of Japanese mustard spinach growth and the increased in plant uptake of phosphates following acid washing were observed. Copyright © 2014 Elsevier Ltd. All rights reserved.

  16. Bioadsorption of nickel Mining Company by residual biomass Phyllanthus Orbicularis

    Directory of Open Access Journals (Sweden)

    Ariel Díaz-Puig

    2017-01-01

    Full Text Available Kinetic parameters for the adsorption of nickel were studied in the waste CalcinationPlant Company Ernesto Che Guevara biomass Phyllanthus orbicularis synthetic and industrial waste Calcination Plant enterprise solutions. The results showed that the major factors influencing the adsorption capacity of the biomass increases with increasing pH and the initial concentration of nickel in the effluent and is reduced by increasing the biomass concentration. Meanwhile, the removal efficiency of residual nickel increases with increasing pH and concentration of biomass and reduced when the initial concentration of nickel in the effluent increases. The adsorption capacity nickel biomass Phyllanthus orbicularis from synthetic solutions and industrial waste Calcination Plant Company Nickel "Comandante Ernesto Che Guevara" was 44,05 and 26,25 mg/g respectively. The adsorption process nickel biomass Phyllanthus orbicularis follows kinetics pseudo-second order and according to the values of free energy of adsorption obtained through model-RadushkevichDubinin was 267,26 kJ/mol, this nature demonstrates that corresponds to a process mediated by chemical adsorption where the formation of stable bonds between the functional groups present in the biomass and the metal ions predominates.

  17. Ensemble Kalman filtering with residual nudging

    KAUST Repository

    Luo, X.

    2012-10-03

    Covariance inflation and localisation are two important techniques that are used to improve the performance of the ensemble Kalman filter (EnKF) by (in effect) adjusting the sample covariances of the estimates in the state space. In this work, an additional auxiliary technique, called residual nudging, is proposed to monitor and, if necessary, adjust the residual norms of state estimates in the observation space. In an EnKF with residual nudging, if the residual norm of an analysis is larger than a pre-specified value, then the analysis is replaced by a new one whose residual norm is no larger than a pre-specified value. Otherwise, the analysis is considered as a reasonable estimate and no change is made. A rule for choosing the pre-specified value is suggested. Based on this rule, the corresponding new state estimates are explicitly derived in case of linear observations. Numerical experiments in the 40-dimensional Lorenz 96 model show that introducing residual nudging to an EnKF may improve its accuracy and/or enhance its stability against filter divergence, especially in the small ensemble scenario.

  18. Validation of welded joint residual stress simulation

    International Nuclear Information System (INIS)

    Computational mechanics is being increasingly applied to predict the state of residual stress in welded joints for nuclear power plant applications. Motives for undertaking such calculations include optimising the design of welded joints and weld procedures, assessing the effectiveness of mitigation processes, providing more realistic inputs to structural integrity assessments and underwriting safety cases for operating nuclear power plant. Fusion welding processes involve intense localised heating to melt the surfaces to be joined and introduction of molten weld filler metal. A complex residual stress field develops at the weld through solidification, differential thermal contraction, cyclic thermal plasticity, phase transformation and chemical diffusion processes. The calculation of weld residual stress involves detailed non-linear analyses where many assumptions and approximations have to be made. In consequence, the accuracy and reliability of solutions can be highly variable. This paper illustrates the degree of variability that can arise in weld residual stress simulation results and summarises the new R6 guidelines which aim to improve the reliability and accuracy of computational predictions. The requirements for validating weld simulations are reviewed where residual stresses are to be used in fracture mechanics analysis. This includes a discussion of how to obtain and interpret measurements from mock-ups, benchmark weldments and published data. Benchmark weldments are described that illustrate some of the issues and show how validation of numerical prediction of weld residual stress can be achieved. Finally, plans for developing the weld modelling guidelines and associated benchmarks are outlined

  19. Residual Stresses in Thermoplastic Composites: A Review

    Directory of Open Access Journals (Sweden)

    M.M. Shokrieh

    2008-12-01

    Full Text Available Applications of thermoplastic composites have developed extensively. The thermoplastic composites in comparison with the thermoset composites have many advantages. Thermoplastic composites can be melted and remolded many times. The duration of manufacturing process of these composites is short, producing very tough material, and the welding ability and multiple recyclings are their further advantages. The lack of knowledge in this group of composites is the main obstacle in their development. In this review the research works in the field of residual stresses in thermoplastic composites is presented. First, a literature survey on the available research on residual stresses on thermoplastics and thermoplastic composites reinforced with short fibers is compiled. Moreover a review on the available research on residual stresses on thermoplastic composites reinforced with long fibers is presented as well. The effects of the residual stresses on these composites are discussed. Experimental techniques for the measurement of residual stresses in thermoplastic composites and the methods for reducing the existing residual stresses are studied.

  20. Ensemble Kalman filtering with residual nudging

    Directory of Open Access Journals (Sweden)

    Xiaodong Luo

    2012-10-01

    Full Text Available Covariance inflation and localisation are two important techniques that are used to improve the performance of the ensemble Kalman filter (EnKF by (in effect adjusting the sample covariances of the estimates in the state space. In this work, an additional auxiliary technique, called residual nudging, is proposed to monitor and, if necessary, adjust the residual norms of state estimates in the observation space. In an EnKF with residual nudging, if the residual norm of an analysis is larger than a pre-specified value, then the analysis is replaced by a new one whose residual norm is no larger than a pre-specified value. Otherwise, the analysis is considered as a reasonable estimate and no change is made. A rule for choosing the pre-specified value is suggested. Based on this rule, the corresponding new state estimates are explicitly derived in case of linear observations. Numerical experiments in the 40-dimensional Lorenz 96 model show that introducing residual nudging to an EnKF may improve its accuracy and/or enhance its stability against filter divergence, especially in the small ensemble scenario.

  1. Residu Fungisida Tembaga (Cu pada Pucuk Teh

    Directory of Open Access Journals (Sweden)

    Christanti Sumardiyono

    1996-12-01

    Full Text Available The study was done to know copper residue on tea due to blister blight control by copper fungicides. The experiment was done at Pagilaran Tea Plantation, Batang, Pekalongan. Tea plants were sprayed 8 times, with 8 days interval at the dosages of 0. 75, 150, and 300 g/ha respectively. Shoot sample was taken at 8 and 16 days after spraying. The copper residue war analyzed by Atomic Adsorbtion Spectrophotometer at 324 nm. The result showed that the higher dosage of spraying gives higher copper residue. At the dosage of 300 g/ha was detected 23,52 ppm of copper residue at 8 days after spraying. The residue was reduced to 12,96 ppm at 16 days after spraying. At that dosage the blister blight disease intensity reduced by 59,97%. The detected residue of copper fungicides due to blister blight control is not higher than MRL ( 150 ppm.

  2. Method for residual household waste composition studies.

    Science.gov (United States)

    Sahimaa, Olli; Hupponen, Mari; Horttanainen, Mika; Sorvari, Jaana

    2015-12-01

    The rising awareness of decreasing natural resources has brought forward the idea of a circular economy and resource efficiency in Europe. As a part of this movement, European countries have identified the need to monitor residual waste flows in order to make recycling more efficient. In Finland, studies on the composition of residual household waste have mostly been conducted using different methods, which makes the comparison of the results difficult. The aim of this study was to develop a reliable method for residual household waste composition studies. First, a literature review on European study methods was performed. Also, 19 Finnish waste composition studies were compared in order to identify the shortcomings of the current Finnish residual household waste composition data. Moreover, the information needs of different waste management authorities concerning residual household waste were studied through a survey and personal interviews. Stratification, sampling, the classification of fractions and statistical analysis were identified as the key factors in a residual household waste composition study. The area studied should be divided into non-overlapping strata in order to decrease the heterogeneity of waste and enable comparisons between different waste producers. A minimum of six subsamples, each 100 kg, from each stratum should be sorted. Confidence intervals for each waste category should be determined in order to evaluate the applicability of the results. A new three-level classification system was created based on Finnish stakeholders' information needs and compared to four other European waste composition study classifications. Copyright © 2015 Elsevier Ltd. All rights reserved.

  3. Detecting organic gunpowder residues from handgun use

    Science.gov (United States)

    MacCrehan, William A.; Ricketts, K. Michelle; Baltzersen, Richard A.; Rowe, Walter F.

    1999-02-01

    The gunpowder residues that remain after the use of handguns or improvised explosive devices pose a challenge for the forensic investigator. Can these residues be reliably linked to a specific gunpowder or ammunition? We investigated the possibility by recovering and measuring the composition of organic additives in smokeless powder and its post-firing residues. By determining gunpowder additives such as nitroglycerin, dinitrotoluene, ethyl- and methylcentralite, and diphenylamine, we hope to identify the type of gunpowder in the residues and perhaps to provide evidence of a match to a sample of unfired powder. The gunpowder additives were extracted using an automated technique, pressurized fluid extraction (PFE). The conditions for the quantitative extraction of the additives using neat and solvent-modified supercritical carbon dioxide were investigated. All of the major gunpowder additives can be determined with baseline resolution using capillary electrophoresis (CE) with a micellar agent and UV absorbance detection. A study of candidate internal standards for use in the CE method is also presented. The PFE/CE technique is used to evaluate a new residue sampling protocol--asking shooters to blow their noses. In addition, an initial investigation of the compositional differences among unfired and post-fired .22 handgun residues is presented.

  4. High Fidelity Modeling of Field Reversed Configuration (FRC) Thrusters

    Science.gov (United States)

    2017-04-22

    particles com- prise electrons and positively singly charged ions . The set S stores the chemical components, and the heavy - particles are stored in the set...torch is made of electrons, atoms and molecules. Charged particles comprise elec- trons and positively singly charged ions . The set S stores the chemical...that the electron and ion number density must always be equal, thereby enforcing charge neutrality. The MHD model is often further simplified to an

  5. Resistivity at the field null of the FRC plasma

    International Nuclear Information System (INIS)

    Gerwin, R.A.

    1989-01-01

    In the absence of the major destructive instabilities, the configuration time is ultimately determined by particle and flux containment. If the profiles are ''gentle,'' then the anomalous flux-loss rate depends essentially on the anomalous resistivity at the field null. Conventional electrostatic quasi-linear models of anomalous cross-field resistive diffusivity are based upon the use of rvec E x rvec B drift velocities, and hence break down at the magnetic field null. In this paper, an electromagnetic treatment valid at the field null is developed, based upon the presence of flute-parity perturbations. An expression for anomalous resistivity at the field null in the quasi-linear approximation is derived by averaging in the ignorable direction over the random phases of the perturbations. The expression is valid for arbitrary (non-local) radial shapes of the perturbing modes (for example, the eigenfunctions need not be centered at the field null), and for an arbitrary ratio of real frequency to growth rate. The effective resistivity due to flute perturbations of the MHD type will be considered. 1 ref

  6. A Fractual Mechanical Testing and Design Strategy for FRC Structures

    DEFF Research Database (Denmark)

    Stang, Henrik; Olesen, John Forbes

    1999-01-01

    A unified testing and design strategy for fibre reinforced concrete structures is summarised. The strategy is based on fracture mechanical concepts. Emphasis is placed on material characterisation and testing specifications.......A unified testing and design strategy for fibre reinforced concrete structures is summarised. The strategy is based on fracture mechanical concepts. Emphasis is placed on material characterisation and testing specifications....

  7. The WST method, a fracture mechanics test method for FRC

    DEFF Research Database (Denmark)

    Lofgren, I.; Stang, Henrik; Olesen, John Forbes

    2008-01-01

    The applicability of the wedge-splitting test method (WST), for determining fracture properties of fibre-reinforced concrete, is discussed. Experimental results, using the WST method, are compared with results from uniaxial tension tests (UTT) and three-point bending tests (3PBT) for five differe...

  8. Genomic and physiological perspectives on bioremediation processes at the FRC

    Energy Technology Data Exchange (ETDEWEB)

    Cardenas, Erick; Leigh, Mary Beth; Hemme, Christopher; Gentry, Terry; Harzman, Christina; Wu, Weimin; Criddle, Craig S.; Zhou, Jizhong; Marsh, Terence; Tiedje, James M.

    2006-04-05

    A suite of molecular and physiological studies, including metal reduction assays, metagenomics, functional gene microarrays and community sequence analyses were applied to investigate organisms involved in bioremediation processes at the ERSP Field Research Center and to understand the effects of stress on the makeup and evolution of microbial communities to inform effective remediation strategies.

  9. Global Development Network: Supporting Global Research Capacity

    International Development Research Centre (IDRC) Digital Library (Canada)

    GDN's capacity-building objective is being strengthened through their Global Research Capacity Building program, which provides up to six years of direct support for collaborative and cross-disciplinary research through regional competitions. This increased focus on capacity building enhances the commonalities with ...

  10. Carrying capacity: maintaining outdoor recreation quality

    Science.gov (United States)

    David W. Lime; George H. Stankey

    1971-01-01

    A discussion of (1) what is meant by the concept of recreational carrying capacity; (2) what is known about capacities in terms of both how resources and experience of visitors are affected by recreational use; and (3) what alternative procedures the administrator can use to manage both resources and visitors for capacity.

  11. Electrochemical impedance studies of capacity fading of ...

    Indian Academy of Sciences (India)

    2017-06-09

    Jun 9, 2017 ... Abstract. Electrodeposited ZnO coatings suffer severe capacity fading when used as conversion anodes in sealed Li cells. Capacity fading is ... coating delivered a stable reversible capacity 16% higher than that delivered by the ..... Ni3+ which not only imparts better electronic conductivity to the material, but ...

  12. The product of capacities and belief functions

    DEFF Research Database (Denmark)

    Hendon, Ebbe; Whitta-Jacobsen, Hans Jørgen; Sloth, Birgitte

    1996-01-01

    Capacities (monotone, non-additive set functions) have been suggested to describe situations of uncertainty. We examine the question of how to define the product of two independent capacities. In particular, for the product of two belief functions (totally monotone capacities), there is a unique...... minimal product belief function. This is characterized in several ways...

  13. The product of capacities and belief functions

    DEFF Research Database (Denmark)

    Hendon, Ebbe; Jacobsen, Hans Jørgen; Sloth, Birgitte

    1996-01-01

    Capacities (monotone, non-additive set functions) have been suggested to describe situations of uncertainty. We examine the question of how to define the product of two independent capacities. In particular, for the product of two belief functions (totally monotone capacities), there is a unique...... minimal product belief function. This is characterized in several ways....

  14. Frequency-dependent heat capacity

    DEFF Research Database (Denmark)

    Behrens, Claus Flensted

    The frequency–dependent heat capacity of super-cooled glycerol near the glass transition is measured using the 3w detection technique. An electrical conducting thin film with a temperature–dependent electrical resistance is deposited on a substrate. The thin film is used simultaneously as a heater...... and as a thermometer. The aim of the work is to improve and understand this planar heater experiment. I find: • Carbon has advantages as heater material over the traditionally used metal (nickel) heaters. • The thermal coupling to the surrounding temperature bath should not be made through the liquid but through...... the substrate. • Edge effects, as a result of the finite size of the heater, play an important role. The traditionally way of dealing with these effects are not entirely correct. • The Cole–Davidson function with bCD...

  15. High current capacity electrical connector

    International Nuclear Information System (INIS)

    Bettis, E.S.; Watts, H.L.

    1976-01-01

    An electrical connector is provided for coupling high current capacity electrical conductors such as copper busses or the like. The connector is arranged in a ''sandwiched'' configuration in which a conductor plate contacts the busses along major surfaces clamped between two stainless steel backing plates. The conductor plate is provided with contact buttons in a spaced array such that the caps of the buttons extend above the conductor plate surface to contact the busses. When clamping bolts provided through openings in the sandwiched arrangement are tightened, Belleville springs provided under the rim of each button cap are compressed and resiliently force the caps into contact with the busses' contacting surfaces to maintain a predetermined electrical contact area provided by the button cap tops. The contact area does not change with changing thermal or mechanical stresses applied to the coupled conductors

  16. The heat capacity mapping mission

    Science.gov (United States)

    Short, N. M.

    1981-01-01

    The first in a series of low cost Atmospheric Explorer Satellites, the Heat Capacity Mapping Mission (HCMM) was designed to evaluate the utility of thermal inertial and other thermal and reflectance data for: (1) discriminating bedrock and unconsolidated regolith types; (2) mapping soil moisture; (3) measuring plant canopy temperatures; (4) examining thermal circulation in large bodies of water; and (5) monitoring urban heat islands. Final reports from the HCMM investigator's program are beginning to define the utility of day/the night thermal data. Under favorable circumstances, some major rock types can be identified, soil moisture in extensive agricultural and alluvial terrains can be detected and at least semiqualitatively assessed; and circulation of currents in large bodies of water can be followed by noting thermal patterns.

  17. Enhanced extraction of phenolic compounds from coffee industry’s residues through solid state fermentation by Penicillium purpurogenum

    Directory of Open Access Journals (Sweden)

    Lady Rossana PALOMINO García

    2015-01-01

    Full Text Available Abstract The use of agroindustrial residues is an economical solution to industrial biotechnology. Coffee husk and pulp are abounding residues from coffee industry which can be used as substrates in solid state fermentation process, thus allowing a liberation and increase in the phenolic compound content with high added value. By employing statistical design, initial moisture content, pH value in the medium, and the incubation temperature were evaluated, in order to increase the polyphenol content in a process of solid state fermentation by Penicillium purpurogenum. The main phenolic compounds identified through HPLC in fermented coffee residue were chlorogenic acid, caffeic acid, and rutin. Data obtained through HPLC with the radical absorbance capacity assay suggest the fermented coffee husk and pulp extracts potential as a source of phenolic acids and flavonoids. Results showed good perspectives when using P. purpurogenum strain to enhance the liberation of phenolic compounds in coffee residues.

  18. Assessing the Availability of Wood Residues and Residue Markets in Virginia

    OpenAIRE

    Alderman, Delton R. Jr.

    1998-01-01

    A statewide mail survey of primary and secondary wood product manufacturers was undertaken to quantify the production and consumption of wood residues in Virginia. Two hundred and sixty-six wood product manufacturers responded to the study and they provided information on the production, consumption, markets, income or disposal costs, and disposal methods of wood residues. Hardwood and pine sawmills produce approximately 66 percent of Virginia's wood residues. Virginia's wood product man...

  19. Cross-phosphorylation of bacterial serine/threonine and tyrosine protein kinases on key regulatory residues

    Directory of Open Access Journals (Sweden)

    Lei eShi

    2014-09-01

    Full Text Available Bacteria possess protein serine/threonine and tyrosine kinases which resemble eukaryal kinases in their capacity to phosphorylate multiple substrates. We hypothesized that the analogy might extend further, and bacterial kinases may also undergo mutual phosphorylation and activation, which is currently considered as a hallmark of eukaryal kinase networks. In order to test this hypothesis, we explored the capacity of all members of four different classes of serine/threonine and tyrosine kinases present in the firmicute model organism Bacillus subtilis to phosphorylate each other in vitro and interact with each other in vivo. The interactomics data suggested a high degree of connectivity among all types of kinases, while phosphorylation assays revealed equally wide-spread cross-phosphorylation events. Our findings suggest that the Hanks-type kinases PrkC, PrkD and YabT exhibit the highest capacity to phosphorylate other B. subtilis kinases, while the BY-kinase PtkA and the two-component-like kinases RsbW and SpoIIAB show the highest propensity to be phosphorylated by other kinases. Analysis of phosphorylated residues on several selected recipient kinases suggests that most cross-phosphorylation events concern key regulatory residues. Therefore, cross-phosphorylation events are very likely to influence the capacity of recipient kinases to phosphorylate substrates downstream in the signal transduction cascade. We therefore conclude that bacterial serine/threonine and tyrosine kinases probably engage in a network-type behavior previously described only in eukaryal cells.

  20. Financing new nuclear capacity: Will the ''nuclear renaissance'' Be a Self-Sustaining reaction?

    Energy Technology Data Exchange (ETDEWEB)

    George, Glenn R.

    2007-04-15

    Although EPAct offers a number of benefits for new nuclear capacity, a host of gaps remain, from the timing of capital formation to the residual risk that the actual cost of the first few plants will significantly exceed estimates. Securitization and related financial techniques could play a role in turning revenue streams into lumps of capital. (author)

  1. Prediction of welding residual distortions of large structures using a local/global approach

    International Nuclear Information System (INIS)

    Duan, Y. G.; Bergheau, J. M.; Vincent, Y.; Boitour, F.; Leblond, J. B.

    2007-01-01

    Prediction of welding residual distortions is more difficult than that of the microstructure and residual stresses. On the one hand, a fine mesh (often 3D) has to be used in the heat affected zone for the sake of the sharp variations of thermal, metallurgical and mechanical fields in this region. On the other hand, the whole structure is required to be meshed for the calculation of residual distortions. But for large structures, a 3D mesh is inconceivable caused by the costs of the calculation. Numerous methods have been developed to reduce the size of models. A local/global approach has been proposed to determine the welding residual distortions of large structures. The plastic strains and the microstructure due to welding are supposed can be determined from a local 3D model which concerns only the weld and its vicinity. They are projected as initial strains into a global 3D model which consists of the whole structure and obviously much less fine in the welded zone than the local model. The residual distortions are then calculated using a simple elastic analysis, which makes this method particularly effective in an industrial context. The aim of this article is to present the principle of the local/global approach then show the capacity of this method in an industrial context and finally study the definition of the local model

  2. CO2 storage in depleted gas reservoirs: A study on the effect of residual gas saturation

    Directory of Open Access Journals (Sweden)

    Arshad Raza

    2018-03-01

    Full Text Available Depleted gas reservoirs are recognized as the most promising candidate for carbon dioxide storage. Primary gas production followed by injection of carbon dioxide after depletion is the strategy adopted for secondary gas recovery and storage practices. This strategy, however, depends on the injection strategy, reservoir characteristics and operational parameters. There have been many studies to-date discussing critical factors influencing the storage performance in depleted gas reservoirs while little attention was given to the effect of residual gas. In this paper, an attempt was made to highlight the importance of residual gas on the capacity, injectivity, reservoir pressurization, and trapping mechanisms of storage sites through the use of numerical simulation. The results obtained indicated that the storage performance is proportionally linked to the amount of residual gas in the medium and reservoirs with low residual fluids are a better choice for storage purposes. Therefore, it would be wise to perform the secondary recovery before storage in order to have the least amount of residual gas in the medium. Although the results of this study are useful to screen depleted gas reservoirs for the storage purpose, more studies are required to confirm the finding presented in this paper.

  3. Recycling of air pollution control residues from municipal solid waste incineration into lightweight aggregates.

    Science.gov (United States)

    Quina, Margarida J; Bordado, João M; Quinta-Ferreira, Rosa M

    2014-02-01

    This work focuses on the assessment of technological properties and on the leaching behavior of lightweight aggregates (LWA) produced by incorporating different quantities of air pollution control (APC) residues from municipal solid waste (MSW) incineration. Currently this hazardous waste has been mostly landfilled after stabilization/solidification. The LWA were produced by pelletizing natural clay, APC residues as-received from incineration plant, or after a washing treatment, a small amount of oil and water. The pellets were fired in a laboratory chamber furnace over calcium carbonate. The main technological properties of the LWA were evaluated, mainly concerning morphology, bulk and particle densities, compressive strength, bloating index, water adsorption and porosity. Given that APC residues do not own expansive (bloating) properties, the incorporation into LWA is only possible in moderate quantities, such as 3% as received or 5% after pre-washing treatment. The leaching behavior of heavy metals from sintered LWA using water or acid solutions was investigated, and despite the low acid neutralization capacity of the synthetic aggregates, the released quantities were low over a wide pH range. In conclusion, after a washing pre-treatment and if the percentage of incorporation is low, these residues may be incorporated into LWA. However, the recycling of APC residues from MSW incineration into LWA does not revealed any technical advantage. Copyright © 2013 Elsevier Ltd. All rights reserved.

  4. Identification of residual tumor with intraoperative contrast-enhanced ultrasound during glioblastoma resection.

    Science.gov (United States)

    Prada, Francesco; Bene, Massimiliano Del; Fornaro, Riccardo; Vetrano, Ignazio G; Martegani, Alberto; Aiani, Luca; Sconfienza, Luca Maria; Mauri, Giovanni; Solbiati, Luigi; Pollo, Bianca; DiMeco, Francesco

    2016-03-01

    The purpose of this study was to assess the capability of contrast-enhanced ultrasound (CEUS) to identify residual tumor mass during glioblastoma multiforme (GBM) surgery, to increase the extent of resection. The authors prospectively evaluated 10 patients who underwent surgery for GBM removal with navigated ultrasound guidance. Navigated B-mode and CEUS were performed prior to resection, during resection, and after complete tumor resection. Areas suspected for residual tumors on B-mode and CEUS studies were localized within the surgical field with navigated ultrasound and samples were sent separately for histopathological analysis to confirm tumor presence. In all cases tumor remnants were visualized as hyperechoic areas on B-mode, highlighted as CEUS-positive areas, and confirmed as tumoral areas on histopathological analysis. In 1 case only, CEUS partially failed to demonstrate residual tumor because the residual hyperechoic area was devascularized prior to ultrasound contrast agent injection. In all cases CEUS enhanced B-mode findings. As has already been shown in other neoplastic lesions in other organs, CEUS is extremely specific in the identification of residual tumor. The ability of CEUS to distinguish between tumor and artifacts or normal brain on B-mode is based on its capacity to show the vascularization degree and not the echogenicity of the tissues. Therefore, CEUS can play a decisive role in the process of maximizing GBM resection.

  5. A survey of residual analysis and a new test of residual trend.

    Science.gov (United States)

    McDowell, J J; Calvin, Olivia L; Klapes, Bryan

    2016-05-01

    A survey of residual analysis in behavior-analytic research reveals that existing methods are problematic in one way or another. A new test for residual trends is proposed that avoids the problematic features of the existing methods. It entails fitting cubic polynomials to sets of residuals and comparing their effect sizes to those that would be expected if the sets of residuals were random. To this end, sampling distributions of effect sizes for fits of a cubic polynomial to random data were obtained by generating sets of random standardized residuals of various sizes, n. A cubic polynomial was then fitted to each set of residuals and its effect size was calculated. This yielded a sampling distribution of effect sizes for each n. To test for a residual trend in experimental data, the median effect size of cubic-polynomial fits to sets of experimental residuals can be compared to the median of the corresponding sampling distribution of effect sizes for random residuals using a sign test. An example from the literature, which entailed comparing mathematical and computational models of continuous choice, is used to illustrate the utility of the test. © 2016 Society for the Experimental Analysis of Behavior.

  6. Pile Load Capacity – Calculation Methods

    Directory of Open Access Journals (Sweden)

    Wrana Bogumił

    2015-12-01

    Full Text Available The article is a review of the current problems of the foundation pile capacity calculations. The article considers the main principles of pile capacity calculations presented in Eurocode 7 and other methods with adequate explanations. Two main methods are presented: α – method used to calculate the short-term load capacity of piles in cohesive soils and β – method used to calculate the long-term load capacity of piles in both cohesive and cohesionless soils. Moreover, methods based on cone CPTu result are presented as well as the pile capacity problem based on static tests.

  7. Capacity analysis of vehicular communication networks

    CERN Document Server

    Lu, Ning

    2013-01-01

    This SpringerBrief focuses on the network capacity analysis of VANETs, a key topic as fundamental guidance on design and deployment of VANETs is very limited. Moreover, unique characteristics of VANETs impose distinguished challenges on such an investigation. This SpringerBrief first introduces capacity scaling laws for wireless networks and briefly reviews the prior arts in deriving the capacity of VANETs. It then studies the unicast capacity considering the socialized mobility model of VANETs. With vehicles communicating based on a two-hop relaying scheme, the unicast capacity bound is deriv

  8. Assessing urban adaptive capacity to climate change.

    Science.gov (United States)

    Araya-Muñoz, Dahyann; Metzger, Marc J; Stuart, Neil; Wilson, A Meriwether W; Alvarez, Luis

    2016-12-01

    Despite the growing number of studies focusing on urban vulnerability to climate change, adaptive capacity, which is a key component of the IPCC definition of vulnerability, is rarely assessed quantitatively. We examine the capacity of adaptation in the Concepción Metropolitan Area, Chile. A flexible methodology based on spatial fuzzy modelling was developed to standardise and aggregate, through a stepwise approach, seventeen indicators derived from widely available census statistical data into an adaptive capacity index. The results indicate that all the municipalities in the CMA increased their level of adaptive capacity between 1992 and 2002. However, the relative differences between municipalities did not change significantly over the studied timeframe. Fuzzy overlay allowed us to standardise and to effectively aggregate indicators with differing ranges and granularities of attribute values into an overall index. It also provided a conceptually sound and reproducible means of exploring the interplay of many indicators that individually influence adaptive capacity. Furthermore, it captured the complex, aggregated and continued nature of the adaptive capacity, favouring to deal with gaps of data and knowledge associated with the concept of adaptive capacity. The resulting maps can help identify municipalities where adaptive capacity is weak and identify which components of adaptive capacity need strengthening. Identification of these capacity conditions can stimulate dialogue amongst policymakers and stakeholders regarding how to manage urban areas and how to prioritise resources for urban development in ways that can also improve adaptive capacity and thus reduce vulnerability to climate change. Copyright © 2016 Elsevier Ltd. All rights reserved.

  9. Sustainable System for Residual Hazards Management

    International Nuclear Information System (INIS)

    Kevin M. Kostelnik; James H. Clarke; Jerry L. Harbour

    2004-01-01

    Hazardous, radioactive and other toxic substances have routinely been generated and subsequently disposed of in the shallow subsurface throughout the world. Many of today's waste management techniques do not eliminate the problem, but rather only concentrate or contain the hazardous contaminants. Residual hazards result from the presence of hazardous and/or contaminated material that remains on-site following active operations or the completion of remedial actions. Residual hazards pose continued risk to humans and the environment and represent a significant and chronic problem that require continuous long-term management (i.e. >1000 years). To protect human health and safeguard the natural environment, a sustainable system is required for the proper management of residual hazards. A sustainable system for the management of residual hazards will require the integration of engineered, institutional and land-use controls to isolate residual contaminants and thus minimize the associated hazards. Engineered controls are physical modifications to the natural setting and ecosystem, including the site, facility, and/or the residual materials themselves, in order to reduce or eliminate the potential for exposure to contaminants of concern (COCs). Institutional controls are processes, instruments, and mechanisms designed to influence human behavior and activity. System failure can involve hazardous material escaping from the confinement because of system degradation (i.e., chronic or acute degradation) or by external intrusion of the biosphere into the contaminated material because of the loss of institutional control. An ongoing analysis of contemporary and historic sites suggests that the significance of the loss of institutional controls is a critical pathway because decisions made during the operations/remedial action phase, as well as decisions made throughout the residual hazards management period, are key to the long-term success of the prescribed system. In fact

  10. Determining anaerobic capacity in sporting activities.

    Science.gov (United States)

    Noordhof, Dionne A; Skiba, Philip F; de Koning, Jos J

    2013-09-01

    Anaerobic capacity/anaerobically attributable power is an important parameter for athletic performance, not only for short high-intensity activities but also for breakaway efforts and end spurts during endurance events. Unlike aerobic capacity, anaerobic capacity cannot be easily quantified. The 3 most commonly used methodologies to quantify anaerobic capacity are the maximal accumulated oxygen deficit method, the critical power concept, and the gross efficiency method. This review describes these methods, evaluates if they result in similar estimates of anaerobic capacity, and highlights how anaerobic capacity is used during sporting activities. All 3 methods have their own strengths and weaknesses and result in more or less similar estimates of anaerobic capacity but cannot be used interchangeably. The method of choice depends on the research question or practical goal.

  11. Correlation between residual level of DNA double-strand breaks and the radiosensitivity of cancer cells

    International Nuclear Information System (INIS)

    Sun Jianxiang; Sun Weijian; Sui Jianli; Zhou Pingkun

    2008-01-01

    Objective: To understand the variation of the DNA double-strand break rejoining capacity among different cultured cancer cell lines and the primary cancer cells from brain cancer patients, and to explore the predictor of radiotherapy responses of cancers. Methods: DNA double-strand breaks (DSBs) were induced by 60 Co γ-irradiation. Pulsed-field gel electrophoresis was used to analyze the initial production and rejoining of DNA DSBs. Radiosensitivity was determined by in vitro assay of clonogenic-forming capacity. Results: A wide variation of radiosensitivity, e.g. the survival parameter of Do varied from 0.65 to 2.15 Gy, was displayed among the eight cell lines derived from different type of cancers. Although differential level of initial DNA DSBs induced by 20 Gy γ-rays was observed among various cell lines, it was not correlated with the radiosensitivity. The deficiency of DNA DSB rejoining in radiosensitive cell lines was shown either in the early rapid-rejoining phase (SX-10 cells) or in the late slow-rejoining phase (A2780 cells). A significant relationship was observed between the residual level of DNA DSBs measured at 2 h post-20 Gy irradiation and the cellular radiosensitivity (D 0 or SF 2 ). The kinetic curves of rejoining DNA DSBs in the primary human brain tumor cells indicated a variation on DSB rejoining capacity among different individual tumor. The residual level of DNA DSBs after 2 h of rejoining post 20 Gy irradiation in primary human brain tumor cells is compatible to the results obtained in vitro culture cancer cell lines. Conclusions: The residual level of DNA DSBs is correlated with radioresistance of cancer cells, and the residual DNA damage is a useful parameter in predicting the response of tumor tissue to radiotherapy. (authors)

  12. New applications of partial residual methodology

    International Nuclear Information System (INIS)

    Uslu, V.R.

    1999-12-01

    The formulation of a problem of interest in the framework of a statistical analysis starts with collecting the data, choosing a model, making certain assumptions as described in the basic paradigm by Box (1980). This stage is is called model building. Then the estimation stage is in order by pretending as if the formulation of the problem was true to obtain estimates, to make tests and inferences. In the final stage, called diagnostic checking, checking of whether there are some disagreements between the data and the model fitted is done by using diagnostic measures and diagnostic plots. It is well known that statistical methods perform best under the condition that all assumptions related to the methods are satisfied. However it is true that having the ideal case in practice is very difficult. Diagnostics are therefore becoming important so are diagnostic plots because they provide a immediate assessment. Partial residual plots that are the main interest of the present study are playing the major role among the diagnostic plots in multiple regression analysis. In statistical literature it is admitted that partial residual plots are more useful than ordinary residual plots in detecting outliers, nonconstant variance, and especially discovering curvatures. In this study we consider the partial residual methodology in statistical methods rather than multiple regression. We have shown that for the same purpose as in the multiple regression the use of partial residual plots is possible particularly in autoregressive time series models, transfer function models, linear mixed models and ridge regression. (author)

  13. Crop Residue Biomass Effects on Agricultural Runoff

    Directory of Open Access Journals (Sweden)

    Damodhara R. Mailapalli

    2013-01-01

    Full Text Available High residue loads associated with conservation tillage and cover cropping may impede water flow in furrow irrigation and thus decrease the efficiency of water delivery and runoff water quality. In this study, the biomass residue effects on infiltration, runoff, and export of total suspended solids (TSS, dissolved organic carbon (DOC, sediment-associated carbon (TSS-C, and other undesirable constituents such as phosphate (soluble P, nitrate (, and ammonium ( in runoff water from a furrow-irrigated field were studied. Furrow irrigation experiments were conducted in 91 and 274 m long fields, in which the amount of residue in the furrows varied among four treatments. The biomass residue in the furrows increased infiltration, and this affected total load of DOC, TSS, and TSS-C. Net storage of DOC took place in the long but not in the short field because most of the applied water ran off in the short field. Increasing field length decreased TSS and TSS-C losses. Total load of , , and soluble P decreased with increasing distance from the inflow due to infiltration. The concentration and load of P increased with increasing residue biomass in furrows, but no particular trend was observed for and . Overall, the constituents in the runoff decreased with increasing surface cover and field length.

  14. Characterization of bound residues in plants

    International Nuclear Information System (INIS)

    Stratton, G.D. Jr.; Wheeler, W.B.

    1986-01-01

    The characterization of unextractable (or 'bound') pesticide residues in plants can be difficult owing to the insoluble nature of the pesticide-plant complex. An unextractable residue can be defined as material derived from the applied pesticide which remains in the plant matrix after exhaustive organic solvent extraction. Experiments with a variety of pesticide classes in plants indicate that the level of unextractable residue varies with the plant species, the pesticide and the exposure time of the plant to the pesticide. Methods used in attempts to release 'bound' residues from solvent-extracted plant tissues include acid hydrolyses, enzymatic treatments and techniques of high-temperature distillation. These methods solubilize or release varying amounts of unextractable material; the amounts depend on the pesticide and on the extent to which the plant fibre is degraded. In experiments using radiolabelled dieldrin (1, 2, 3, 4, 10, 10-hexachloro-6, 7-epoxy-1, 4, 4a, 5, 6, 7, 8, 8a-octahydro-exo-1, 4-endo-5,6-dimethanonaphthalene), carbofuran (2,3-dihydro-2, 2-dimethylbenzofuran-7-yl methylcarbamate) and permethrin ([3-phenoxybenzyl(+-)-3-(2, 2-dichlorovinyl)-2, 2-dimethylcyclopropanecarboxylate]) in radishes, portions of the unextractable material solubilized by the above methods were identified as parent compound and/or closely related metabolites. The bioavailability and toxicological significance of unextractable pesticide residues need to be evaluated. (author)

  15. Reclamation of plutonium from pyrochemical processing residues

    International Nuclear Information System (INIS)

    Gray, L.W.; Gray, J.H.; Holcomb, H.P.; Chostner, D.F.

    1987-04-01

    Savannah River Laboratory (SRL), Savannah River Plant (SRP), and Rocky Flats Plant (RFP) have jointly developed a process to recover plutonium from molten salt extraction residues. These NaCl, KCL, and MgCl 2 residues, which are generated in the pyrochemical extraction of 241 Am from aged plutonium metal, contain up to 25 wt % dissolved plutonium and up to 2 wt % americium. The overall objective was to develop a process to convert these residues to a pure plutonium metal product and discardable waste. To meet this objective a combination of pyrochemical and aqueous unit operations was used. The first step was to scrub the salt residue with a molten metal (aluminum and magnesium) to form a heterogeneous ''scrub alloy'' containing nominally 25 wt % plutonium. This unit operation, performed at RFP, effectively separated the actinides from the bulk of the chloride salts. After packaging in aluminum cans, the ''scrub alloy'' was then dissolved in a nitric acid - hydrofluoric acid - mercuric nitrate solution at SRP. Residual chloride was separated from the dissolver solution by precipitation with Hg 2 (NO 3 ) 2 followed by centrifuging. Plutonium was then separated from the aluminum, americium and magnesium using the Purex solvent extraction system. The 241 Am was diverted to the waste tank farm, but could be recovered if desired

  16. Methods of measuring residual stresses in components

    International Nuclear Information System (INIS)

    Rossini, N.S.; Dassisti, M.; Benyounis, K.Y.; Olabi, A.G.

    2012-01-01

    Highlights: ► Defining the different methods of measuring residual stresses in manufactured components. ► Comprehensive study on the hole drilling, neutron diffraction and other techniques. ► Evaluating advantage and disadvantage of each method. ► Advising the reader with the appropriate method to use. -- Abstract: Residual stresses occur in many manufactured structures and components. Large number of investigations have been carried out to study this phenomenon and its effect on the mechanical characteristics of these components. Over the years, different methods have been developed to measure residual stress for different types of components in order to obtain reliable assessment. The various specific methods have evolved over several decades and their practical applications have greatly benefited from the development of complementary technologies, notably in material cutting, full-field deformation measurement techniques, numerical methods and computing power. These complementary technologies have stimulated advances not only in measurement accuracy and reliability, but also in range of application; much greater detail in residual stresses measurement is now available. This paper aims to classify the different residual stresses measurement methods and to provide an overview of some of the recent advances in this area to help researchers on selecting their techniques among destructive, semi destructive and non-destructive techniques depends on their application and the availabilities of those techniques. For each method scope, physical limitation, advantages and disadvantages are summarized. In the end this paper indicates some promising directions for future developments.

  17. Rare Earth Element Phases in Bauxite Residue

    Directory of Open Access Journals (Sweden)

    Johannes Vind

    2018-02-01

    Full Text Available The purpose of present work was to provide mineralogical insight into the rare earth element (REE phases in bauxite residue to improve REE recovering technologies. Experimental work was performed by electron probe microanalysis with energy dispersive as well as wavelength dispersive spectroscopy and transmission electron microscopy. REEs are found as discrete mineral particles in bauxite residue. Their sizes range from <1 μm to about 40 μm. In bauxite residue, the most abundant REE bearing phases are light REE (LREE ferrotitanates that form a solid solution between the phases with major compositions (REE,Ca,Na(Ti,FeO3 and (Ca,Na(Ti,FeO3. These are secondary phases formed during the Bayer process by an in-situ transformation of the precursor bauxite LREE phases. Compared to natural systems, the indicated solid solution resembles loparite-perovskite series. LREE particles often have a calcium ferrotitanate shell surrounding them that probably hinders their solubility. Minor amount of LREE carbonate and phosphate minerals as well as manganese-associated LREE phases are also present in bauxite residue. Heavy REEs occur in the same form as in bauxites, namely as yttrium phosphates. These results show that the Bayer process has an impact on the initial REE mineralogy contained in bauxite. Bauxite residue as well as selected bauxites are potentially good sources of REEs.

  18. Mobility of organic carbon from incineration residues

    International Nuclear Information System (INIS)

    Ecke, Holger; Svensson, Malin

    2008-01-01

    Dissolved organic carbon (DOC) may affect the transport of pollutants from incineration residues when landfilled or used in geotechnical construction. The leaching of dissolved organic carbon (DOC) from municipal solid waste incineration (MSWI) bottom ash and air pollution control residue (APC) from the incineration of waste wood was investigated. Factors affecting the mobility of DOC were studied in a reduced 2 6-1 experimental design. Controlled factors were treatment with ultrasonic radiation, full carbonation (addition of CO 2 until the pH was stable for 2.5 h), liquid-to-solid (L/S) ratio, pH, leaching temperature and time. Full carbonation, pH and the L/S ratio were the main factors controlling the mobility of DOC in the bottom ash. Approximately 60 weight-% of the total organic carbon (TOC) in the bottom ash was available for leaching in aqueous solutions. The L/S ratio and pH mainly controlled the mobilization of DOC from the APC residue. About 93 weight-% of TOC in the APC residue was, however, not mobilized at all, which might be due to a high content of elemental carbon. Using the European standard EN 13 137 for determination of total organic carbon (TOC) in MSWI residues is inappropriate. The results might be biased due to elemental carbon. It is recommended to develop a TOC method distinguishing between organic and elemental carbon

  19. Uranium enrichment: technology, economics, capacity

    International Nuclear Information System (INIS)

    Voigt, W.R. Jr.; Vanstrum, P.R.; Saire, D.E.; Gestson, D.K.; Peske, S.E.

    1982-01-01

    Large-scale enrichment of uranium has now been carried out for 40 years. While the gaseous diffusion process was the original choice of several countries and continues today to provide the major component of the world production of separative work, the last two decades have witnessed the development of a number of alternative processes for enrichment. These processes, which are being studied and deployed around the world, offer a wide range of technical and economic characteristics which will be useful in assuring adequate capacity to meet projected reactor fuel market needs through the rest of this century at competitive prices. With present uncertainties in future enriched uranium needs, it is apparent that flexibility in the deployment and operation of any enrichment process will be one of the prime considerations for the future. More economical production of separative work not only can have a beneficial impact on reactor fuel costs, but also tends to conserve natural uranium resources. This paper reviews the world scene in the enrichment component of the fuel cycle, including existing or planned commercial-scale facilities and announced R and D efforts on various processes

  20. Novelties that change carrying capacity.

    Science.gov (United States)

    Erwin, Douglas H

    2012-09-01

    Comparative developmental studies have revealed a rich array of details about the patterns and processes of morphological change in animals and increasingly in plants. But, applying these insights to the study of major episodes of evolutionary innovation requires understanding how these novel morphologies become established and sufficiently abundant (either as individuals within a species or as a clade of species) to be preserved in the fossil record, and, in many cases, to influence ecological processes. Evolutionary novelties may: (1) disappear without changing the species; (2) be associated with the generation (through selection or drift) of a new species; and if the latter (3) may or may not become ecologically significant. Only the latter are commonly preserved in the fossil record. These alternatives mirror the distinction among historians of technology between innovation and invention. Here, I argue that specific sorts of evolutionary inventions drive ecological transformation, essentially constructing an environment for themselves and ancillary organisms through ecological spillover effects, increasing the "carrying capacity" of an ecosystem. Copyright © 2011 Wiley Periodicals, Inc.

  1. HIV communication capacity strengthening: a critical review.

    Science.gov (United States)

    Lettenmaier, Cheryl; Kraft, Joan Marie; Raisanen, Keris; Serlemitsos, Elizabeth

    2014-08-15

    HIV communication is most effective and sustainable when it is designed and implemented locally and tailored to the local context. This requires capacity strengthening at national, subnational, and community levels. Through a review of the published and selected "grey" literature, we examine HIV communication capacity strengthening: definitions, measurements, implementation, and effects. We found limited documentation of HIV communication capacity needs or systematic approaches to address them. Most HIV communication capacity strengthening to date has focused on building individual competencies to design and manage social and behavior change communication programs through training courses, often coupled with networking opportunities for participants, post-training mentoring, and technical assistance. A few of these efforts have been evaluated through pre- and post-training tests and qualitative interviews with participants and have shown potential for improvement in individual skills and knowledge. Health communication capacity assessment tools that measure individual and organizational competencies exist, but they have most often been used to identify capacity building needs, not for evaluating capacity strengthening efforts. A new definition of capacity strengthening, grown out of recent efforts to improve effectiveness of international health and development programs, focuses on improving organizational and societal systems that support performance and individual competencies. We propose a holistic model for HIV communication capacity strengthening and call for rigorous documentation and evaluation to determine and scale-up optimal capacity building interventions for strengthening social and behavior change communication for HIV prevention, care, and treatment in developing countries.

  2. Improved crop residue cover estimates by coupling spectral indices for residue and moisture

    Science.gov (United States)

    Remote sensing assessment of soil residue cover (fR) and tillage intensity will improve our predictions of the impact of agricultural practices and promote sustainable management. Spectral indices for estimating fR are sensitive to soil and residue water content, therefore, the uncertainty of estima...

  3. Geostatistical methods applied to field model residuals

    DEFF Research Database (Denmark)

    Maule, Fox; Mosegaard, K.; Olsen, Nils

    consists of measurement errors and unmodelled signal), and is typically assumed to be uncorrelated and Gaussian distributed. We have applied geostatistical methods to analyse the residuals of the Oersted(09d/04) field model [http://www.dsri.dk/Oersted/Field_models/IGRF_2005_candidates/], which is based......The geomagnetic field varies on a variety of time- and length scales, which are only rudimentary considered in most present field models. The part of the observed field that can not be explained by a given model, the model residuals, is often considered as an estimate of the data uncertainty (which...... on 5 years of Ørsted and CHAMP data, and includes secular variation and acceleration, as well as low-degree external (magnetospheric) and induced fields. The analysis is done in order to find the statistical behaviour of the space-time structure of the residuals, as a proxy for the data covariances...

  4. Residual strains in girth-welded linepipe

    International Nuclear Information System (INIS)

    MacEwen, S.R.; Holden, T.M.; Powell, B.M.; Lazor, R.B.

    1987-07-01

    High resolution neutron diffraction has been used to measure the axial residual strains in and adjacent to a multipass girth weld in a complete section of 914 mm (36 inches) diameter, 16 mm (5/8 inch) wall, linepipe. The experiments were carried out at the NRU reactor, Chalk River using the L3 triple-axis spectrometer. The through-wall distribution of axial residual strain was measured at 0, 4, 8, 20 and 50 mm from the weld centerline; the axial variation was determined 1, 5, 8, and 13 mm from the inside surface of the pipe wall. The results have been compared with strain gauge measurements on the weld surface and with through-wall residual stress distributions determined using the block-layering and removal technique

  5. Field Test Kit for Gun Residue Detection

    Energy Technology Data Exchange (ETDEWEB)

    WALKER, PAMELA K.; RODACY, PHILIP J.

    2002-01-01

    One of the major needs of the law enforcement field is a product that quickly, accurately, and inexpensively identifies whether a person has recently fired a gun--even if the suspect has attempted to wash the traces of gunpowder off. The Field Test Kit for Gunshot Residue Identification based on Sandia National Laboratories technology works with a wide variety of handguns and other weaponry using gunpowder. There are several organic chemicals in small arms propellants such as nitrocellulose, nitroglycerine, dinitrotoluene, and nitrites left behind after the firing of a gun that result from the incomplete combustion of the gunpowder. Sandia has developed a colorimetric shooter identification kit for in situ detection of gunshot residue (GSR) from a suspect. The test kit is the first of its kind and is small, inexpensive, and easily transported by individual law enforcement personnel requiring minimal training for effective use. It will provide immediate information identifying gunshot residue.

  6. Residual-strength determination in polymetric materials

    International Nuclear Information System (INIS)

    Christensen, R.M.

    1981-01-01

    Kinetic theory of crack growth is used to predict the residual strength of polymetric materials acted upon by a previous history. Specifically, the kinetic theory is used to characterize the state of growing damage that occurs under a constant-stress (load) state. The load is removed before failure under creep-rupture conditions, and the residual instantaneous strength is determined from the theory by taking account of the damage accumulation under the preceding constant-load history. The rate of change of residual strength is found to be strongest when the duration of the preceding load history is near the ultimate lifetime under that condition. Physical explanations for this effect are given, as are numerical examples. Also, the theoretical prediction is compared with experimental data

  7. Methyl bromide residues in fumigated cocoa beans

    International Nuclear Information System (INIS)

    Adomako, D.

    1975-01-01

    The 14 C activity in unroasted [ 14 C]-methyl bromide fumigated cocoa beans was used to study the fate and persistence of CH 3 Br in the stored beans. About 70% of the residues occurred in the shells. Unchanged CH 3 Br could not be detected, all the sorbed CH 3 Br having reacted with bean constituents apparently to form 14 C-methylated derivatives and inorganic bromide. No 14 C activity was found in the lipid fraction. Roasting decreased the bound (non-volatile) residues, with corresponding changes in the activities and amounts of free sugars, free and protein amino acids. Roasted nibs and shells showed a two-fold increase in the volatile fraction of the 14 C residue. This fraction may be related to the volatile aroma compounds formed by Maillard-type reactions. (author)

  8. Determination of Pesticide Residues in Cannabis Smoke

    Directory of Open Access Journals (Sweden)

    Nicholas Sullivan

    2013-01-01

    Full Text Available The present study was conducted in order to quantify to what extent cannabis consumers may be exposed to pesticide and other chemical residues through inhaled mainstream cannabis smoke. Three different smoking devices were evaluated in order to provide a generalized data set representative of pesticide exposures possible for medical cannabis users. Three different pesticides, bifenthrin, diazinon, and permethrin, along with the plant growth regulator paclobutrazol, which are readily available to cultivators in commercial products, were investigated in the experiment. Smoke generated from the smoking devices was condensed in tandem chilled gas traps and analyzed with gas chromatography-mass spectrometry (GC-MS. Recoveries of residues were as high as 69.5% depending on the device used and the component investigated, suggesting that the potential of pesticide and chemical residue exposures to cannabis users is substantial and may pose a significant toxicological threat in the absence of adequate regulatory frameworks.

  9. Bioenergy from agricultural residues in Ghana

    DEFF Research Database (Denmark)

    Thomsen, Sune Tjalfe

    and biomethane under Ghanaian conditions. Detailed characterisations of thirteen of the most common agricultural residues in Ghana are presented, enabling estimations of theoretical bioenergy potentials and identifying specific residues for future biorefinery applications. When aiming at residue-based ethanol...... to pursue increased implementation of anaerobic digestion in Ghana, as the first bioenergy option, since anaerobic digestion is more flexible than ethanol production with regard to both feedstock and scale of production. If possible, the available manure and municipal liquid waste should be utilised first....... A novel model for estimating BMP from compositional data of lignocellulosic biomasses is derived. The model is based on a statistical method not previously used in this area of research and the best prediction of BMP is: BMP = 347 xC+H+R – 438 xL + 63 DA , where xC+H+R is the combined content of cellulose...

  10. Mutational properties of amino acid residues: implications for evolvability of phosphorylatable residues

    DEFF Research Database (Denmark)

    Creixell, Pau; Schoof, Erwin M.; Tan, Chris Soon Heng

    2012-01-01

    in terms of their mutational activity. Moreover, we highlight the importance of the genetic code and physico-chemical properties of the amino acid residues as likely causes of these inequalities and uncover serine as a mutational hot spot. Finally, we explore the consequences that these different......; it is typically assumed that all amino acid residues are equally likely to mutate or to result from a mutation. Here, by reconstructing ancestral sequences and computing mutational probabilities for all the amino acid residues, we refute this assumption and show extensive inequalities between different residues...... mutational properties have on phosphorylation site evolution, showing that a higher degree of evolvability exists for phosphorylated threonine and, to a lesser extent, serine in comparison with tyrosine residues. As exemplified by the suppression of serine's mutational activity in phosphorylation sites, our...

  11. TCR-contacting residues orientation and HLA-DRβ* binding preference determine long-lasting protective immunity against malaria

    International Nuclear Information System (INIS)

    Alba, Martha P.; Suarez, Carlos F.; Varela, Yahson; Patarroyo, Manuel A.; Bermudez, Adriana; Patarroyo, Manuel E.

    2016-01-01

    Fully-protective, long-lasting, immunological (FPLLI) memory against Plasmodium falciparum malaria regarding immune protection-inducing protein structures (IMPIPS) vaccinated into monkeys previously challenged and re-challenged 60 days later with a lethal Aotus monkey-adapted P. falciparum strain was found to be associated with preferential high binding capacity to HLA-DRβ1* allelic molecules of the major histocompatibility class II (MHC-II), rather than HLA-DRβ3*, β4*, β5* alleles. Complete PPII L 3D structure, a longer distance (26.5 Å ± 1.5 Å) between residues perfectly fitting into HLA-DRβ1*PBR pockets 1 and 9, a gauche − rotamer orientation in p8 TCR-contacting polar residue and a larger volume of polar p2 residues was also found. This data, in association with previously-described p3 and p7 apolar residues having gauche + orientation to form a perfect MHC-II-peptide-TCR complex, determines the stereo-electronic and topochemical characteristics associated with FPLLI immunological memory. - Highlights: • Stereo-electronic and topochemical rules associated with FPLLI immunological memory. • Presence of very high long-lasting antibody titres against Plasmodium falciparum Spz. • Protective memory induction associated with a binding capacity to HLA-DRβ1*. • gauche − rotamer orientation in p8 polar residue is related to is related to immunological memory.

  12. TCR-contacting residues orientation and HLA-DRβ* binding preference determine long-lasting protective immunity against malaria

    Energy Technology Data Exchange (ETDEWEB)

    Alba, Martha P.; Suarez, Carlos F. [Fundación Instituto de Inmunología de Colombia (FIDIC), Bogotá D. C. (Colombia); Universidad del Rosario, Bogotá D. C. (Colombia); Universidad de Ciencias Aplicadas y Ambientales (UDCA), Bogotá (Colombia); Varela, Yahson [Fundación Instituto de Inmunología de Colombia (FIDIC), Bogotá D. C. (Colombia); Patarroyo, Manuel A.; Bermudez, Adriana [Fundación Instituto de Inmunología de Colombia (FIDIC), Bogotá D. C. (Colombia); Universidad del Rosario, Bogotá D. C. (Colombia); Patarroyo, Manuel E., E-mail: mepatarr@gmail.com [Fundación Instituto de Inmunología de Colombia (FIDIC), Bogotá D. C. (Colombia); Universidad Nacional de Colombia, Bogotá D. C. (Colombia)

    2016-09-02

    Fully-protective, long-lasting, immunological (FPLLI) memory against Plasmodium falciparum malaria regarding immune protection-inducing protein structures (IMPIPS) vaccinated into monkeys previously challenged and re-challenged 60 days later with a lethal Aotus monkey-adapted P. falciparum strain was found to be associated with preferential high binding capacity to HLA-DRβ1* allelic molecules of the major histocompatibility class II (MHC-II), rather than HLA-DRβ3*, β4*, β5* alleles. Complete PPII{sub L} 3D structure, a longer distance (26.5 Å ± 1.5 Å) between residues perfectly fitting into HLA-DRβ1*PBR pockets 1 and 9, a gauche{sup −} rotamer orientation in p8 TCR-contacting polar residue and a larger volume of polar p2 residues was also found. This data, in association with previously-described p3 and p7 apolar residues having gauche{sup +} orientation to form a perfect MHC-II-peptide-TCR complex, determines the stereo-electronic and topochemical characteristics associated with FPLLI immunological memory. - Highlights: • Stereo-electronic and topochemical rules associated with FPLLI immunological memory. • Presence of very high long-lasting antibody titres against Plasmodium falciparum Spz. • Protective memory induction associated with a binding capacity to HLA-DRβ1*. • gauche{sup −} rotamer orientation in p8 polar residue is related to is related to immunological memory.

  13. 40 CFR 180.564 - Indoxacarb; tolerances for residues.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Indoxacarb; tolerances for residues...) PESTICIDE PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances § 180.564 Indoxacarb; tolerances for residues. (a) General. Tolerances are established for residues of...

  14. Feeding potential of summer grain crop residues for woolled sheep ...

    African Journals Online (AJOL)

    greater amounts than indicated in Table 2. Percentage utilization of residues. Using the values obtained from quadrat sampling of the residues before and after grazing, the percentage utilization of residue components could be estimated. The results are shown in Table 3. Table 3 Percentage utilization a of residues. Lupins.

  15. 40 CFR 180.176 - Mancozeb; tolerances for residues.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Mancozeb; tolerances for residues. 180... PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances § 180.176 Mancozeb; tolerances for residues. (a) General. Tolerances for residues of a fungicide which is a...

  16. 40 CFR 180.324 - Bromoxynil; tolerances for residues.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Bromoxynil; tolerances for residues...) PESTICIDE PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances § 180.324 Bromoxynil; tolerances for residues. (a) General. (1) Tolerances are established for residues...

  17. 40 CFR 180.314 - Triallate; tolerances for residues.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Triallate; tolerances for residues...) PESTICIDE PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances § 180.314 Triallate; tolerances for residues. (a) General. Tolerances are established for residues of...

  18. 40 CFR 180.210 - Bromacil; tolerances for residues.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Bromacil; tolerances for residues. 180... PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances § 180.210 Bromacil; tolerances for residues. (a) General. Tolerances are established for residues of the herbicide...

  19. 40 CFR 279.47 - Management of residues.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 26 2010-07-01 2010-07-01 false Management of residues. 279.47 Section... Management of residues. Transporters who generate residues from the storage or transport of used oil must manage the residues as specified in § 279.10(e). ...

  20. 40 CFR 180.298 - Methidathion; tolerances for residues.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Methidathion; tolerances for residues...) PESTICIDE PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances § 180.298 Methidathion; tolerances for residues. (a) General. Tolerances are established for residues of...

  1. 40 CFR 180.299 - Dicrotophos; tolerances for residues.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Dicrotophos; tolerances for residues...) PESTICIDE PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances § 180.299 Dicrotophos; tolerances for residues. (a) General. Tolerances are established for residues of...

  2. 40 CFR 180.227 - Dicamba; tolerances for residues.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Dicamba; tolerances for residues. 180... PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances § 180.227 Dicamba; tolerances for residues. (a) General. (1) Tolerances are established for the combined residues of...

  3. 40 CFR 180.209 - Terbacil; tolerances for residues.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Terbacil; tolerances for residues. 180... PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances § 180.209 Terbacil; tolerances for residues. (a) General. Tolerances are established for combined residues of the...

  4. 40 CFR 180.249 - Alachlor; tolerances for residues.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Alachlor; tolerances for residues. 180... PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances § 180.249 Alachlor; tolerances for residues. (a) General. Tolerances are established for combined residues of...

  5. 40 CFR 180.128 - Pyrethrins; tolerances for residues.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Pyrethrins; tolerances for residues...) PESTICIDE PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances § 180.128 Pyrethrins; tolerances for residues. (a) General. (1) Tolerances for residues of the...

  6. 40 CFR 279.67 - Management of residues.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 26 2010-07-01 2010-07-01 false Management of residues. 279.67 Section... for Energy Recovery § 279.67 Management of residues. Burners who generate residues from the storage or burning of used oil must manage the residues as specified in § 279.10(e). ...

  7. 40 CFR 180.208 - Benfluralin; tolerances for residues.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Benfluralin; tolerances for residues...) PESTICIDE PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances § 180.208 Benfluralin; tolerances for residues. (a) General. Tolerances are established for residues of...

  8. 40 CFR 180.178 - Ethoxyquin; tolerances for residues.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Ethoxyquin; tolerances for residues...) PESTICIDE PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances § 180.178 Ethoxyquin; tolerances for residues. (a) General. A tolerance is established for residues of...

  9. 40 CFR 180.241 - Bensulide; tolerances for residues.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Bensulide; tolerances for residues...) PESTICIDE PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances § 180.241 Bensulide; tolerances for residues. (a) General. Tolerances are established for the residues...

  10. 40 CFR 180.263 - Phosalone; tolerances for residues.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Phosalone; tolerances for residues...) PESTICIDE PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances § 180.263 Phosalone; tolerances for residues. (a) General. Tolerances are established for residues of...

  11. 40 CFR 180.258 - Ametryn; tolerances for residues.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Ametryn; tolerances for residues. 180... PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances § 180.258 Ametryn; tolerances for residues. (a) General. Tolerances are established for residues of the desiccant...

  12. 40 CFR 180.213 - Simazine; tolerances for residues.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Simazine; tolerances for residues. 180... PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances § 180.213 Simazine; tolerances for residues. (a) General. Tolerances are established for the combined residues of the...

  13. 40 CFR 180.269 - Aldicarb; tolerances for residues.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Aldicarb; tolerances for residues. 180... PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances § 180.269 Aldicarb; tolerances for residues. (a) General. Tolerances are established for combined residues of the...

  14. 40 CFR 180.315 - Methamidophos; tolerances for residues.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Methamidophos; tolerances for residues...) PESTICIDE PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances § 180.315 Methamidophos; tolerances for residues. (a) Tolerances are established for residues of the...

  15. 40 CFR 180.235 - Dichlorvos; tolerances for residues.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Dichlorvos; tolerances for residues...) PESTICIDE PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances § 180.235 Dichlorvos; tolerances for residues. (a) General. (1) Tolerances for residues of the...

  16. 40 CFR 180.222 - Prometryn; tolerances for residues.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Prometryn; tolerances for residues...) PESTICIDE PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances § 180.222 Prometryn; tolerances for residues. (a) General. Tolerances are established for residues of...

  17. 40 CFR 180.262 - Ethoprop; tolerances for residues.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Ethoprop; tolerances for residues. 180... PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances § 180.262 Ethoprop; tolerances for residues. (a) General. Tolerances are established for residues of the nematocide...

  18. 40 CFR 279.59 - Management of residues.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 26 2010-07-01 2010-07-01 false Management of residues. 279.59 Section... Management of residues. Owners and operators who generate residues from the storage, processing, or re-refining of used oil must manage the residues as specified in § 279.10(e). ...

  19. 40 CFR 180.198 - Trichlorfon; tolerances for residues.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Trichlorfon; tolerances for residues...) PESTICIDE PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances § 180.198 Trichlorfon; tolerances for residues. (a) General. Tolerances are established for residues of...

  20. 40 CFR 180.304 - Oryzalin; tolerances for residues.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Oryzalin; tolerances for residues. 180... PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances § 180.304 Oryzalin; tolerances for residues. (a) General. Tolerances are established for residues of the herbicide...

  1. 40 CFR 180.169 - Carbaryl; tolerances for residues.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Carbaryl; tolerances for residues. 180... PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances § 180.169 Carbaryl; tolerances for residues. (a) General. (1) Tolerances are established for residues of the...

  2. 40 CFR 180.220 - Atrazine; tolerances for residues.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Atrazine; tolerances for residues. 180... PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances § 180.220 Atrazine; tolerances for residues. (a) General. Tolerances are established for the combined residues of the...

  3. 40 CFR 180.122 - Parathion; tolerances for residues.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Parathion; tolerances for residues...) PESTICIDE PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances § 180.122 Parathion; tolerances for residues. (a) General. Tolerances are established for residues of...

  4. 40 CFR 180.200 - Dicloran; tolerances for residues.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Dicloran; tolerances for residues. 180... PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances § 180.200 Dicloran; tolerances for residues. (a) General. (1) Tolerances are established for residues of the...

  5. 40 CFR 180.133 - Lindane; tolerances for residues.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Lindane; tolerances for residues. 180... PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances § 180.133 Lindane; tolerances for residues. (a) General. Tolerances are established for residues of the insecticide...

  6. 40 CFR 180.328 - Napropamide; tolerances for residues.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Napropamide; tolerances for residues...) PESTICIDE PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances § 180.328 Napropamide; tolerances for residues. (a) General. Tolerances are established for residues of...

  7. 40 CFR 180.132 - Thiram; tolerances for residues.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Thiram; tolerances for residues. 180... PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances § 180.132 Thiram; tolerances for residues. (a) General. Tolerances are established for residues of the fungicide...

  8. 40 CFR 180.243 - Propazine; tolerances for residues.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Propazine; tolerances for residues...) PESTICIDE PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances § 180.243 Propazine; tolerances for residues. Tolerances are established for negligible residues (N) of...

  9. 40 CFR 180.301 - Carboxin; tolerances for residues.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Carboxin; tolerances for residues. 180... PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances § 180.301 Carboxin; tolerances for residues. (a) General. Tolerances are established for the combined residues of the...

  10. 51st North American Chemical Residue Workshop.

    Science.gov (United States)

    Yang, Paul; Martos, Perry; Barrett, Brad

    2015-06-03

    Manuscripts collected in this 51st North American Chemical Residue Workshop (NACRW) Symposium issue of the Journal of Agricultural and Food Chemistry (JAFC) were originally presented at the 51st NACRW meeting. The 2014 NACRW JAFC symposium collects 14 publications representing the broad range of topics in chemical analyses presented at the 2014 meeting. These include the analysis of chemical residues and contaminants in food, environment, feed, botanical, and bee samples as well as the application of quality control/quality assurance protocols in routine and method development.

  11. Residual generator for cardiovascular anomalies detection

    KAUST Repository

    Belkhatir, Zehor

    2014-06-01

    This paper discusses the possibility of using observer-based approaches for cardiovascular anomalies detection and isolation. We consider a lumped parameter model of the cardiovascular system that can be written in a form of nonlinear state-space representation. We show that residuals that are sensitive to variations in some cardiovascular parameters and to abnormal opening and closure of the valves, can be generated. Since the whole state is not easily available for measurement, we propose to associate the residual generator to a robust extended kalman filter. Numerical results performed on synthetic data are provided.

  12. Fate of leptophos residues in milk products

    International Nuclear Information System (INIS)

    Zayed, S.M.A.D.; Mohammed, S.I.

    1981-01-01

    The fate of leptophos residues in various milk products was studied using 14 C-phenyl labelled leptophos. Milk products were prepared from milk fortified with the radioactive insecticide by methods simulating those used in industry. The highest leptophos level was found in butter and the lowest in skim milk and whey. Analysis of the radioactive residues in all products showed the presence of leptophos alone. A trace of the oxon could be detected in whey. The results obtained in this investigation indicated that processing of milk did not affect the nature of leptophos to any appreciable extent. (author)

  13. Residual stress in Ni-W electrodeposits

    DEFF Research Database (Denmark)

    Mizushima, Io; Tang, Peter Torben; Hansen, Hans Nørgaard

    2006-01-01

    In the present work, the residual stress in Ni–W layers electrodeposited from electrolytes based on NiSO4 and Na2WO4, is investigated. Citrate, glycine and triethanolamine were used as complexing agents, enabling complex formation between the nickel ion and tungstate. The results show that the type...... of complexing agent and the current efficiency have an influence on the residual stress. In all cases, an increase in tensile stress in the deposit with time after deposition was observed. Pulse plating could improve the stress level for the electrolyte containing equal amounts of citrate...

  14. Fluidised-bed combustion of gasification residue

    Energy Technology Data Exchange (ETDEWEB)

    Korpela, T.; Kudjoi, A.; Hippinen, I.; Heinolainen, A.; Suominen, M.; Lu Yong [Helsinki Univ. of Technology (Finland). Lab of Energy Economics and Power Plant Engineering

    1996-12-01

    Partial gasification processes have been presented as possibilities for future power production. In the processes, the solid materials removed from a gasifier (i.e. fly ash and bed material) contain unburnt fuel and the fuel conversion is increased by burning this gasification residue either in an atmospheric or a pressurised fluidised-bed. In this project, which is a part of European JOULE 2 EXTENSION research programme, the main research objectives are the behaviour of calcium and sulphur compounds in solids and the emissions of sulphur dioxide and nitrogen oxides (NO{sub x} and N{sub 2}O) in pressurised fluidised-bed combustion of gasification residues. (author)

  15. Mechanically induced residual stresses: Modelling and characterisation

    Science.gov (United States)

    Stranart, Jean-Claude E.

    Accurate characterisation of residual stress represents a major challenge to the engineering community. This is because it is difficult to validate the measurement and the accuracy is doubtful. It is with this in mind that the current research program concerning the characterisation of mechanically induced residual stresses was undertaken. Specifically, the cold expansion of fastener holes and the shot peening treatment of aerospace alloys, aluminium 7075 and titanium Ti-6Al-4V, are considered. The objective of this study is to characterise residual stresses resulting from cold working using three powerful techniques. These are: (i) theoretical using three dimensional non-linear finite element modelling, (ii) semi-destructive using a modified incremental hole drilling technique and (iii) nondestructive using a newly developed guided wave method supplemented by traditional C-scan measurements. The three dimensional finite element results of both simultaneous and sequential cold expansion of two fastener holes revealed the importance of the separation distance, the expansion level and the loading history upon the development and growth of the plastic zone and unloading residual stresses. It further showed that the commonly adopted two dimensional finite element models are inaccurate and incapable of predicting these residual stresses. Similarly, the dynamic elasto-plastic finite element studies of shot peening showed that the depth of the compressed layer, surface and sub-surface residual stresses are significantly influenced by the shot characteristics. Furthermore, the results reveal that the separation distance between two simultaneously impacting shots governs the plastic zone development and its growth. In the semi-destructive incremental hole drilling technique, the accuracy of the newly developed calibration coefficients and measurement techniques were verified with a known stress field and the method was used to measure peening residual stresses. Unlike

  16. Some problems of residual activity measurements

    International Nuclear Information System (INIS)

    Katrik, P.; Mustafin, E.; Strasik, I.; Pavlovic, M.

    2013-01-01

    As a preparatory work for constructing the Facility for Antiproton and Ion Research (FAIR) at GSI Darmstadt, samples of copper were irradiated by 500 MeV/u 238 U ion beam and investigated by gamma-ray spectroscopy. The nuclides that contribute dominantly to the residual activity have been identified and their contributions have been quantified by two different methods: from the whole-target gamma spectra and by integration of depth-profiles of residual activity of individual nuclides. Results obtained by these two methods are compared and discussed in this paper. (authors)

  17. Residual water treatment for gamma radiation

    International Nuclear Information System (INIS)

    Mendez, L.

    1990-01-01

    The treatment of residual water by means of gamma radiation for its use in agricultural irrigation is evaluated. Measurements of physical, chemical, biological and microbiological contamination indicators were performed. For that, samples from the treatment center of residual water of San Juan de Miraflores were irradiated up to a 52.5 kGy dose. The study concludes that gamma radiation is effective to remove parasites and bacteria, but not for removal of the organic and inorganic matter. (author). 15 refs., 3 tabs., 4 figs

  18. Lindane residues in fish inhabiting Nigerian rivers

    International Nuclear Information System (INIS)

    Okereke, G.U.; Dje, Y.

    1997-01-01

    Analysis for residues of lindane in fish collected from various rivers close to rice agroecosystems showed that the concentrations of lindane ranged from none detectable to 3.4 mg kg -1 . Fish from rivers where strict regulations prohibits its use had no detectable lindane residues while appreciable amounts of lindane were found in fish were such restriction was not enforced with the variation attributed to the extent of use of lindane in the area of contamination. The investigation confirms that the use of lindane in rice production in Nigeria can cause the contamination of fish in nearby rivers. (author). 16 refs, 2 tab

  19. Residual radioactivity of treated green diamonds.

    Science.gov (United States)

    Cassette, Philippe; Notari, Franck; Lépy, Marie-Christine; Caplan, Candice; Pierre, Sylvie; Hainschwang, Thomas; Fritsch, Emmanuel

    2017-08-01

    Treated green diamonds can show residual radioactivity, generally due to immersion in radium salts. We report various activity measurements on two radioactive diamonds. The activity was characterized by alpha and gamma ray spectrometry, and the radon emanation was measured by alpha counting of a frozen source. Even when no residual radium contamination can be identified, measurable alpha and high-energy beta emissions could be detected. The potential health impact of radioactive diamonds and their status with regard to the regulatory policy for radioactive products are discussed. Copyright © 2017. Published by Elsevier Ltd.

  20. Effective capacity of correlated MISO channels

    KAUST Repository

    Zhong, Caijun

    2011-06-01

    This paper presents an analytical performance investigation of the capacity limits of correlated multiple-input single-output (MISO) channels in the presence of quality-of-service (QoS) requirements. Exact closed-form expression for the effective capacity of correlated MISO channels is derived. In addition, simple expressions are obtained at the asymptotic high and low signal-to-noise ratio (SNR) regimes, which provide insights into the impact of various system parameters on the effective capacity of the system. Also, a complete characterization of the impact of spatial correlation on the effective capacity is provided with the aid of a majorization theory result. The findings suggest that antenna correlation reduce the effective capacity of the channels. Moreover, a stringent QoS requirement causes a significant reduction in the effective capacity but this can be effectively alleviated by increasing the number of antennas. © 2011 IEEE.

  1. North Dakota Refining Capacity Study

    Energy Technology Data Exchange (ETDEWEB)

    Dennis Hill; Kurt Swenson; Carl Tuura; Jim Simon; Robert Vermette; Gilberto Marcha; Steve Kelly; David Wells; Ed Palmer; Kuo Yu; Tram Nguyen; Juliam Migliavacca

    2011-01-05

    According to a 2008 report issued by the United States Geological Survey, North Dakota and Montana have an estimated 3.0 to 4.3 billion barrels of undiscovered, technically recoverable oil in an area known as the Bakken Formation. With the size and remoteness of the discovery, the question became 'can a business case be made for increasing refining capacity in North Dakota?' And, if so what is the impact to existing players in the region. To answer the question, a study committee comprised of leaders in the region's petroleum industry were brought together to define the scope of the study, hire a consulting firm and oversee the study. The study committee met frequently to provide input on the findings and modify the course of the study, as needed. The study concluded that the Petroleum Area Defense District II (PADD II) has an oversupply of gasoline. With that in mind, a niche market, naphtha, was identified. Naphtha is used as a diluent used for pipelining the bitumen (heavy crude) from Canada to crude markets. The study predicted there will continue to be an increase in the demand for naphtha through 2030. The study estimated the optimal configuration for the refinery at 34,000 barrels per day (BPD) producing 15,000 BPD of naphtha and a 52 percent refinery charge for jet and diesel yield. The financial modeling assumed the sponsor of a refinery would invest its own capital to pay for construction costs. With this assumption, the internal rate of return is 9.2 percent which is not sufficient to attract traditional investment given the risk factor of the project. With that in mind, those interested in pursuing this niche market will need to identify incentives to improve the rate of return.

  2. Chemical Characterization and Water Holding Capacity of Fibre-rich Feedstuffs Used for Pigs in Vietnam

    Directory of Open Access Journals (Sweden)

    T. T. B. Ngoc

    2012-06-01

    Full Text Available During two years, four samples per year were collected in Vietnam from rice bran, cassava residue, brewer’s grain, tofu residue, soybean meal, coconut cake, sweet potato vines and water spinach for chemical analysis and assessment of water holding capacity (WHC. The selected feedstuffs represent fibre-rich plant sources and agro-industry co-products commonly used in pig feeding in Vietnam. The content (g/kg DM of crude protein (CP, ether extract (EE and non-starch polysaccharides (NSP varied between feedstuffs and ranged from 21 to 506 for CP, from 14 to 118 for EE and from 197 to 572 for NSP. Cassava residue had a high starch content of 563 g/kg DM, while sweet potato vines, water spinach, coconut cake and soybean meal had a high content of sugars (63–71 g/kg DM. The content of individual neutral sugars varied between feed ingredients, with the highest content of arabinose, galactose and glucose in tofu residue, the highest content of xylose in brewer’s grain and the highest content of mannose in coconut cake. The content of uronic acid was high for cassava residue, tofu residue, sweet potato vines and water spinach (57–88 g/kg DM. The content of soluble non-cellulosic polysaccharides (S-NCP was positively correlated (r2 = 0.82 to the WHC. The content (g/kg DM of CP, NDF, neutral sugars, total NSP, total NCP, S-NCP and total dietary fibre in tofu residue, water spinach and coconut cake varied (p<0.05 between years. In conclusion, diet formulation to pigs can be improved if the variation in chemical composition of the fibre fraction and in WHC between potential feed ingredients is taken into account.

  3. The capacity of digital links in tandem

    Science.gov (United States)

    Posner, E. C.; Rubin, A. L.

    1984-01-01

    The present investigation is concerned with the error control strategy used in connection with digital data networks, taking into account the capacity of the end-to-end channel. It is assumed that the only source of noise is Gaussian and that bandwidth limitation on capacity can be ignored. Attention is given to L links in tandem with binary repeaters, the asymptotic capacity with a large number of links, some alternative repeater strategies, and approaches for lowering the bit error probability. Numerical results are presented, taking into consideration capacity versus link error probability for various numbers of links.

  4. Strategic Mobility 21: Rail Network Capacity Analysis

    National Research Council Canada - National Science Library

    Mallon, Lawrence G; Leachman, Robert C; Fetty, George R

    2006-01-01

    This analysis examined the rail network capacity and average transit times for commercial and surge military deployments through the proposed Victorville - Joint Power Projection Support Platform (JPPSP...

  5. Narrative medicine and decision-making capacity.

    Science.gov (United States)

    Mahr, Greg

    2015-06-01

    The author proposes a new model for the assessment of decision-making capacity based on the principles of narrative medicine. The narrative method proposed by the author addresses the hidden power realtionships implicit in the current model of capacity assessment. Sample cases are reviewed using the traditional model in comparison with the narrative model. Narrative medicine provides an effective model for the assessment of decision-making capacity. Deficiencies in the traditional model capacity assessment can be effectively addressed using narrative strategies. © 2015 John Wiley & Sons, Ltd.

  6. Population growth and earth's human carrying capacity.

    Science.gov (United States)

    Cohen, J E

    1995-07-21

    Earth's capacity to support people is determined both by natural constraints and by human choices concerning economics, environment, culture (including values and politics), and demography. Human carrying capacity is therefore dynamic and uncertain. Human choice is not captured by ecological notions of carrying capacity that are appropriate for nonhuman populations. Simple mathematical models of the relation between human population growth and human carrying capacity can account for faster-than-exponential population growth followed by a slowing population growth rate, as observed in recent human history.

  7. A comparative analysis of capacity adequacy policies

    International Nuclear Information System (INIS)

    Doorman, Gerard; Botterud, Audun; Wolfgang, Ove

    2007-06-01

    In this paper a stochastic dynamic optimization model is used to analyze the effect of different generation adequacy policies in restructured power systems. The expansion decisions of profit-maximizing investors are simulated under a number of different market designs: Energy Only with and without a price cap, Capacity Payment, Capacity Obligation, Capacity Subscription, and Demand Elasticity. The results show that the overall social welfare is reduced compared to a centralized social welfare optimization for all policies except Capacity Subscription and Demand Elasticity. In particular, an energy only market with a low price cap leads to a significant increase in involuntary load shedding. Capacity payments and obligations give additional investment incentives and more generating capacity, but also result in a considerable transfer of wealth from consumers to producers due to the capacity payments. Increased demand elasticity increases social welfare, but also results in a transfer from producers to consumers, compared to the theoretical social welfare optimum. In contrast, the capacity subscription policy increases the social welfare, and both producers and consumers benefit. This is possible because capacity subscription explicitly utilizes differences in consumers' preferences for uninterrupted supply. This advantage must be weighed against the cost of implementation, which is not included in the model.

  8. [Study on purification of total flavonoids from seed residue of Hippophae rhamnoides with macroporous resin].

    Science.gov (United States)

    Cao, Qun-hua; Qu, Wei-jing; Li, Jia-gui; Deng, Yun-xia

    2004-03-01

    To study the conditions and parameters of purifying total flavonoids from seed residue of H. rhamnoides. Absorption capacity of three resins for total flavonoids was compared. With the yield and purity as indexes, the process of absorbing and purifying total flavonoids from seed residue with D101 macroporous resin absorbent was selected by orthogonal design. The D101 resin was the best of the three resins and its absorption capacity was determined to be 63.00 mg x g(-1) wet resin. The optimum process condition was 30% ethanol as eluting solvent, wet resin vs crude herbs: 2:1, diameter vs height: 1:10, eluting solvent vs crude herbs: 10:1, absorbing time for 3 h. The yield of total flavonoids from seeds residue of H. rhamnoides by this process was 2.39%, and the purity reached 64.81%. The process is simple and convenient and the regeneration of resin is easy. So this method of purification is advisable.

  9. Efficiency Improvement of Some Agricultural Residue Modified Materials for Textile Dyes Absorption

    Science.gov (United States)

    Boonsong, P.; Paksamut, J.

    2018-03-01

    In this work, the adsorption efficiency was investigated of some agricultural residue modified materials as natural bio-adsorbents which were rice straw (Oryza sativa L.) and pineapple leaves (Ananas comosus (L.) Merr.) for the removal of textile dyes. Reactive dyes were used in this research. The improvement procedure of agricultural residue materials properties were alkali-acid modification with sodium hydroxide solution and hydrochloric acid solution. Adsorption performance has been investigated using batch experiments. Investigated adsorption factors consisted of adsorbent dose, contact time, adsorbent materials and pH of solution. The results were found that rice straw had higher adsorption capacity than pineapple leaves. The increasing of adsorption capacity depends on adsorbent dose and contact time. Moreover, the optimum pH for dye adsorption was acidic range because lowering pH increased the positively charges on the adsorbent surface which could be attacked by negatively charge of acid dyes. The agricultural residue modified materials had significant dye removal efficiency which these adsorbents could be used for the treatment of textile effluent in industries.

  10. Management of industrial solid residues; Gerenciamento de residuos solidos industriais

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-07-01

    This chapter gives an overview on the management of industrial solid wastes, approaching the following subjects: classification of industrial solid residues; directives and methodologies for the management of industrial solid residues; instruments for the management of industrial solid residues; handling, packing, storage and transportation; treatment of industrial solid residues; final disposal - landfill for industrial residues; the problem of treatment and final disposer of domestic garbage in Brazil; recycling of the lubricant oils used in brazil; legislation.

  11. Risk-Based Approach to Developing National Residue Sampling Plan

    OpenAIRE

    Scientific Committee of the Food Safety Authority of Ireland

    2014-01-01

    A ranking system for veterinary medicinal products and medicated feed additives has been developed as a tool to be applied in a risk-based approach to the residue testing programme for foods of animal origin in the National Residue Control Plan. In the context of food sampling and residue testing for the National Residue Control Plan, there is firstly, the risk to human health from residues of chemical substances in food and secondly, the issue of non-compliance with regulations relating ...

  12. The effect of a fiber reinforced cavity configuration on load bearing capacity and failure mode of endodontically treated molars restored with CAD/CAM resin composite overlay restorations.

    Science.gov (United States)

    Rocca, G T; Saratti, C M; Cattani-Lorente, M; Feilzer, A J; Scherrer, S; Krejci, I

    2015-09-01

    To evaluate the fracture strength and the mode of failure of endodontically treated molars restored with CAD/CAM overlays with fiber reinforced composite build-up of the pulp chamber. 40 Devitalized molars were cut over the CEJ and divided into five groups (n=8). The pulp chamber area was filled with: group 0 (control), no resin build-up; group 1, hybrid composite build-up (G-aenial posterior, GC); group 2, as in group 1 but covered with 3 nets of bi-directional E-glass fibers (EverStickNET, Stick Tech Ltd.); group 3, a FRC resin (EverX posterior, GC); group 4, as in group 3 but covered by the bi-directional fibers. The crowns were restored with CAD-CAM composite restorations (Lava Ultimate, 3M ESPE). Maximum fracture loads were recorded in Newton and data were analyzed using Kruskal-Wallis test (p0.05). All specimens fractured in a catastrophic way, under the CEJ. The main crack evolved in the corono-apical direction. In groups 2 and 4 secondary fracture paths with apico-coronal direction were detected close to the bi-directional fibers' layer. For the restoration of endodontically treated molars, the incorporation of FRCs did not influence the load-bearing capacity of the tooth-restoration complex. The SEM analysis showed a low ability of the bi-directional fibers net in deviating the fracture but this effect was not sufficient to lead more favorable fracture patterns, over the CEJ. The use of FRCs to reinforce the "core" of devitalized molars against vertical fractures under static loads seems useless when the thickness of the CAD/CAM composite overlay restoration is high. Copyright © 2015 Elsevier Ltd. All rights reserved.

  13. Proceedings of the 7. biennial residue-to-revenue residual wood conference 2007

    International Nuclear Information System (INIS)

    Raulin, J.

    2007-01-01

    This conference provided information on the highest and best use of residual wood, which is quickly becoming a valuable commodity. Issues concerning forest residues, sawmill wastes, agricultural residues and urban organic materials were discussed along with trends in Canadian surplus mill waste production. The evolving nature and technologies of the biomass business were highlighted with particular focus on how to generate energy and save money through the use of residual wood. Residual wood energy projects and developments in Canada, North America and Europe were outlined along with biomass development in relation to forest fires and insect disturbances. Cogeneration technologies using wood wastes for thermal heat, steam and electricity were also presented, along with transportation fuel technologies for the production of ethanol. It was noted that with the rising cost of energy, the forest industry is seeking energy solutions based on the use of residual wood. The range of economically practical residual wood solutions continues to grow as energy prices increase. The conference was attended by more than 200 delegates from the forest industry, suppliers and government representatives, to discuss policies and procedures currently in place. Industry investment is being stimulated by the potential for biofuels and biochemicals, as well as the co-operation between the forest and energy sectors. The conference featured 23 presentations, of which 12 have been catalogued separately for inclusion in this database. refs., tabs., figs

  14. Residual Momentum and Reversal Strategies Revisited

    NARCIS (Netherlands)

    J.J. Huij (Joop); S.D. Lansdorp (Simon)

    2017-01-01

    textabstractIn this note we revisit the 2011 and 2013 papers of Blitz, Huij, and Martens (BHM2011), and Blitz, Huij, Lansdorp, and Verbeek (BHLV2013) in which momentum and reversal strategies on residual returns are proposed. Our results indicate that the main findings of these studies, that

  15. Recovery of silver residues from dental amalgam.

    Science.gov (United States)

    Pereira, Heloísa Aparecida Barbosa da Silva; Iano, Flávia Godoy; da Silva, Thelma Lopes; de Oliveira, Rodrigo Cardoso; de Menezes, Manoel Lima; Buzalaf, Marília Afonso Rabelo

    2010-01-01

    Dental amalgam residues are probably the most important chemical residues generated from clinical dental practice because of the presence of heavy metals among its constituents, mainly mercury and silver. The purpose of this study was to develop an alternative method for the recovery of silver residues from dental amalgam. The residue generated after vacuum distillation of dental amalgam for the separation of mercury was initially diluted with 32.5% HNO3, followed by precipitation with 20% NaCl. Sequentially, under constant heating and agitation with NaOH and sucrose, the sample was reduced to metallic silver. However, the processing time was too long, which turned this procedure not viable. In another sequence of experiments, the dilution was accomplished with concentrated HNO3 at 90 degrees C, followed by precipitation with 20% NaCl. After washing, the pellet was diluted with concentrated NH4OH, water and more NaCl in order to facilitate the reaction with the reducer. Ascorbic acid was efficiently used as reducer, allowing a fast reduction, thus making the procedure viable. The proposed methodology is of easy application and does not require sophisticated equipment or expensive reagents.

  16. Recovery of silver residues from dental amalgam

    Directory of Open Access Journals (Sweden)

    Heloísa Aparecida Barbosa da Silva Pereira

    2010-04-01

    Full Text Available Dental amalgam residues are probably the most important chemical residues generated from clinical dental practice because of the presence of heavy metals among its constituents, mainly mercury and silver. OBJECTIVE: The purpose of this study was to develop an alternative method for the recovery of silver residues from dental amalgam. MATERIAL AND METHODS: The residue generated after vacuum distillation of dental amalgam for the separation of mercury was initially diluted with 32.5% HNO3, followed by precipitation with 20% NaCl. Sequentially, under constant heating and agitation with NaOH and sucrose, the sample was reduced to metallic silver. However, the processing time was too long, which turned this procedure not viable. In another sequence of experiments, the dilution was accomplished with concentrated HNO3 at 90ºC, followed by precipitation with 20% NaCl. After washing, the pellet was diluted with concentrated NH4OH, water and more NaCl in order to facilitate the reaction with the reducer. RESULTS: Ascorbic acid was efficiently used as reducer, allowing a fast reduction, thus making the procedure viable. CONCLUSIONS: The proposed methodology is of easy application and does not require sophisticated equipment or expensive reagents.

  17. Agrochemicals and Residues Newsletter. No. 6

    International Nuclear Information System (INIS)

    1991-09-01

    This newsletter provides very brief summaries of the current coordinated research programs and of the completed coordinated research program on the study of the biological activity and bioavailability of bound pesticide residues using nuclear techniques (a more complete report will be published in the IAEA Panel Proceedings series). Research in progress at the Agrochemicals Unit of the IAEA Laboratory in Seibersdorf is also described

  18. The measurement of residual stresses in claddings

    International Nuclear Information System (INIS)

    Hofer, G.; Bender, N.

    1978-01-01

    The ring core method, a variation of the hole drilling method for the measurement of biaxial residual stresses, has been extended to measure stresses from depths of about 5 to 25mm. It is now possible to measure the stress profiles of clad material. Examples of measured stress profiles are shown and compared with those obtained with a sectioning technique. (author)

  19. EFFECTS OF MUCUNA ( MUCUNA UTILIS L.) RESIDUE ...

    African Journals Online (AJOL)

    The field experiment was conducted at two locations: University of Agriculture, Abeokuta (UNAAB) and Olowo-Papa (OP) in Ogun state both in Forest-savannah transition zone of Nigeria to investigate the response of three upland rice cultivars (O.sativa) to mucuna residue incorporation and Nitrogen (N) fertilizer and the ...

  20. Preliminary characterization of residual biomass from Hibiscus ...

    African Journals Online (AJOL)

    Hibiscus sabdariffa calyces are mainly used for different agro-food and beverages applications. The residual biomass generated contains various useful substances that were extracted and characterized. It contained 23% (w/w) soluble pectic material, a food additive, extracted with hot acidified water (80°C, pH = 1.5) and ...