WorldWideScience

Sample records for residence time soot

  1. Role of Fluid-Dynamics in Soot Formation and Microstructure in Acetylene-Air Laminar Diffusion Flames

    Directory of Open Access Journals (Sweden)

    Praveen Pandey

    2015-03-01

    Full Text Available Residence time and thermo-chemical environment are important factors in the soot-formation process in flames. Studies have revealed that flow-dynamics plays a dominant role in soot formation process. For understanding the effect of flow dynamics on soot formation and physical structure of the soot formed in different combustion environments two types of laminar diffusion flames of Acetylene and air, a normal diffusion flame (NDF and an inverse diffusion flame (IDF have been investigated. The fuel and air supply in the reaction zone in two flame types were kept constant but the interchange of relative position of fuel and air altered the burner exit Reynolds and Froude numbers of gases, fuel/air velocity ratio and flame shape. Soot samples were collected using thermophoretic sampling on transmission electron microscope (TEM grids at different flame heights and were analyzed off-line in a Transmission Electron Microscope. Soot primary particle size, soot aggregate size and soot volume fraction were measured using an image analysis software. In NDF the maximum flame temperature was about 1525 K and 1230 K for IDF. The soot primary particles are distinctly smaller in size in IDF (between 19 – 26 nm compared to NDF (between 29–34 nm. Both NDF and IDF show chainlike branched structure of soot agglomerate with soot particles of a nearly spherical shape. The average number of soot primary particles per aggregate in NDF was in the range of 24 to 40 and in IDF it varied between 16 to 24. Soot volume fraction was between 0.6 to 1.5 ppm in NDF where as it was less than 0.2 ppm in IDF. The change in sooting characteristics of the two flame types is attributed to changed fuel/air velocity ratio, entrainment of gas molecules and thermophoresis on soot particles.

  2. A Time Study of Plastic Surgery Residents.

    Science.gov (United States)

    Lau, Frank H; Sinha, Indranil; Jiang, Wei; Lipsitz, Stuart R; Eriksson, Elof

    2016-05-01

    Resident work hours are under scrutiny and have been subject to multiple restrictions. The studies supporting these changes have not included data on surgical residents. We studied the workday of a team of plastic surgery residents to establish prospective time-study data of plastic surgery (PRS) residents at a single tertiary-care academic medical center. Five trained research assistants observed all residents (n = 8) on a PRS service for 10 weeks and produced minute-by-minute activity logs. Data collection began when the team first met in the morning and continued until the resident being followed completed all non-call activities. We analyzed our data from 3 perspectives: 1) time spent in direct patient care (DPC), indirect patient care, and didactic activities; 2) time spent in high education-value activities (HEAs) versus low education-value activities; and 3) resident efficiency. We defined HEAs as activities that surgeons must master; other activities were LEAs. We quantified resident efficiency in terms of time fragmentation and time spent waiting. A total of 642.4 hours of data across 50 workdays were collected. Excluding call, residents worked an average of 64.2 hours per week. Approximately 50.7% of surgical resident time was allotted to DPC, with surgery accounting for the largest segment of this time (34.8%). Time spent on HEAs demonstrated trended upward with higher resident level (P = 0.086). Time in spent in surgery was significantly associated with higher resident levels (P time study of PRS residents, we found that compared with medicine trainees, surgical residents spent 3.23 times more time on DPC. High education-value activities comprised most of our residents' workdays. Surgery was the leading component of both DPC and HEAs. Our residents were highly efficient and fragmented, with the majority of all activities requiring 4 minutes or less. Residents spent a large portion of their time waiting for other services. In light of these data, we

  3. Real-time analysis of soot emissions from bituminous coal pyrolysis and combustion with a vacuum ultraviolet photoionization aerosol time-of-flight mass spectrometer.

    Science.gov (United States)

    Gao, Shaokai; Zhang, Yang; Meng, Junwang; Shu, Jinian

    2009-01-15

    This paper reports on-line analyses of the soot emissions from the Inner Mongolia bituminous coal combustion and pyrolysis processes with a vacuum ultraviolet photoionization aerosol time-of-flight mass spectrometer (VUV-ATOFMS). The soot particles are generated by heating a small amount of screened coal powder in synthetic air and nitrogen atmosphere in a tubular oven. The vacuum ultraviolet photoionization time-of-flight (VUV-TOF) mass spectra of the soot particles emitted from combustion and pyrolysis at different oven temperatures and different stages are obtained. The VUV-TOF mass spectra are assigned with the references of the results of the off-line GC/MS analysis.

  4. Emission, Structure and Optical Properties of Overfire Soot from Buoyant Turbulent Diffusion Flames

    Science.gov (United States)

    Koylu, Umit Ozgur

    The present study investigated soot and carbon monoxide emissions, and evaluated the optical properties of soot, in the overfire region of buoyant turbulent diffusion flames burning in still air. Soot and carbon monoxide emissions, and the corresponding correlation between these emissions, were studied experimentally. The optical properties of soot were investigated both experimentally and theoretically. The experiments involved gas (acetylene, propylene, ethylene, propane, methane) and liquid (toluene, benzene, n-heptane, iso-propanol, ethanol, methanol) fuels. The investigation was limited to the fuel-lean (overfire) region of buoyant turbulent diffusion flames burning in still air. Measurements included flame heights, characteristic flame residence times, carbon monoxide and soot concentrations, mixture fractions, ex-situ soot structure parameters (primary particle sizes, number of primary particles in aggregates, fractal dimensions), and in-situ optical cross sections (differential scattering, total scattering, and absorption) of soot in the overfire region of buoyant turbulent diffusion flames, emphasizing conditions in the long residence time regime where these properties are independent of position in the overfire region and flame residence time. The predictions of optical cross sections for polydisperse aggregates were based on Rayleigh-Debye-Gans theory for fractal aggregates; the predictions of this theory were evaluated by combining the TEM structure and the light scattering/extinction measurements. Carbon monoxide concentrations and mixture fractions were correlated in the overfire region of gas- and liquid -fueled turbulent diffusion flames. Soot volume fraction state relationships were observed for liquid fuels, supporting earlier observations for gas fuels. A strong correlation between carbon monoxide and soot concentrations was established in the fuel-lean region of both gas- and liquid-fueled turbulent diffusion flames. The structure and emission

  5. Subsonic aircraft soot. A tracer documenting barriers to inter-hemispheric mixing

    Energy Technology Data Exchange (ETDEWEB)

    Pueschel, R.F. [NASA Ames Research Center, Moffett Field, CA (United States)

    1997-12-31

    Meridional observations of soot aerosols and radioactive {sup 14}C, and models of the geographic distribution of nuclear bomb-released {sup 14}C and aircraft-emitted NO{sub x}, all show strong gradients between the hemispheres. Reason for it are decade-long inter-hemispheric mixing times which are much in excess of yearlong stratospheric residence times of tracers. Vertical mixing of soot aerosol is not corroborated by {sup 14}C observations. The reason could be radiometric forces that act on strongly absorbing soot. (author) 10 refs.

  6. Time-averaged probability density functions of soot nanoparticles along the centerline of a piloted turbulent diffusion flame using a scanning mobility particle sizer

    KAUST Repository

    Chowdhury, Snehaunshu

    2017-01-23

    In this study, we demonstrate the use of a scanning mobility particle sizer (SMPS) as an effective tool to measure the probability density functions (PDFs) of soot nanoparticles in turbulent flames. Time-averaged soot PDFs necessary for validating existing soot models are reported at intervals of ∆x/D∆x/D = 5 along the centerline of turbulent, non-premixed, C2H4/N2 flames. The jet exit Reynolds numbers of the flames investigated were 10,000 and 20,000. A simplified burner geometry based on a published design was chosen to aid modelers. Soot was sampled directly from the flame using a sampling probe with a 0.5-mm diameter orifice and diluted with N2 by a two-stage dilution process. The overall dilution ratio was not evaluated. An SMPS system was used to analyze soot particle concentrations in the diluted samples. Sampling conditions were optimized over a wide range of dilution ratios to eliminate the effect of agglomeration in the sampling probe. Two differential mobility analyzers (DMAs) with different size ranges were used separately in the SMPS measurements to characterize the entire size range of particles. In both flames, the PDFs were found to be mono-modal in nature near the jet exit. Further downstream, the profiles were flatter with a fall-off at larger particle diameters. The geometric mean of the soot size distributions was less than 10 nm for all cases and increased monotonically with axial distance in both flames.

  7. Drug target residence time: a misleading concept.

    Science.gov (United States)

    Folmer, Rutger H A

    2018-01-01

    Since the importance of drug target residence time was first highlighted more 10 years ago, slow binding kinetics has received much attention in the drug discovery literature, and indeed within pharmaceutical research. However, the residence concept as presented in most papers is supported by rather misleading simulations and arguments, and by examples where compounds are taken out of their pharmacokinetic context. Moreover, fast association is typically more desirable than slow, and advantages of long residence time, notably a potential disconnect between pharmacodynamics (PD) and pharmacokinetics (PK), would be partially or completely offset by slow on-rate. Therefore, plain potency is likely a better predictor of drug development success than is residence time. Copyright © 2017 Elsevier Ltd. All rights reserved.

  8. On Soot Inception in Nonpremixed Flames and the Effects of Flame Structure

    Science.gov (United States)

    Chao, B. H.; Liu, S.; Axelbaum, R. L.; Gokoglu, Suleyman (Technical Monitor)

    1998-01-01

    A simplified three-step model of soot inception has been employed with high activation energy asymptotics to study soot inception in nonpremixed counterflow systems with emphasis on understanding the effects of hydrodynamics and transport. The resulting scheme yields three zones: (1) a fuel oxidation zone wherein the fuel and oxidizer react to form product as well as a radical R, (e.g., H), (2) a soot/precursor formation zone where the radical R reacts with fuel to form "soot/precursor" S, and (3) a soot/precursor consumption zone where S reacts with the oxidizer to form product. The kinetic scheme, although greatly simplified, allows the coupling between soot inception and flame structure to be assessed. The results yield flame temperature, flame location, and a soot/precursor index S(sub I) as functions of Damkohler number for S formation. The soot/precursor index indicates the amount of S at the boundary of the formation region. The flame temperature indirectly indicates the total amount of S integrated over the formation region because as S is formed less heat release is available. The results show that unlike oxidation reactions, an extinction turning-point behavior does not exist for soot. Instead, the total amount of S slowly decreases with decreasing Damkohler number (increasing strain rate), which is consistent with counterflow flame experiments. When the Lewis number of the radical is decreased from unity, the total S reduces due to reduced residence time for the radical in the soot formation region. Similarly, when the Lewis number of the soot/precursor is increased from unity the amount of S increases for all Damkohler numbers. In addition to studying fuel-air (low stoichiometric mixture fraction) flames, the air-side nitrogen was substituted into the fuel, yielding diluted fuel-oxygen (high stoichiometric mixture fraction) flames with the same flame temperature as the fuel - air flames. The relative flame locations were different however, and

  9. Residence time and physical processes in lakes

    Directory of Open Access Journals (Sweden)

    Nicoletta SALA

    2003-09-01

    Full Text Available The residence time of a lake is highly dependent on internal physical processes in the water mass conditioning its hydrodynamics; early attempts to evaluate this physical parameter emphasize the complexity of the problem, which depends on very different natural phenomena with widespread synergies. The aim of this study is to analyse the agents involved in these processes and arrive at a more realistic definition of water residence time which takes account of these agents, and how they influence internal hydrodynamics. With particular reference to temperate lakes, the following characteristics are analysed: 1 the set of the lake's caloric components which, along with summer heating, determine the stabilizing effect of the surface layers, and the consequent thermal stratification, as well as the winter destabilizing effect; 2 the wind force, which transfers part of its momentum to the water mass, generating a complex of movements (turbulence, waves, currents with the production of active kinetic energy; 3 the water flowing into the lake from the tributaries, and flowing out through the outflow, from the standpoint of hydrology and of the kinetic effect generated by the introduction of these water masses into the lake. These factors were studied in the context of the general geographical properties of the lake basin and the watershed (latitude, longitude, morphology, also taking account of the local and regional climatic situation. Also analysed is the impact of ongoing climatic change on the renewal of the lake water, which is currently changing the equilibrium between lake and atmosphere, river and lake, and relationships

  10. Atmospheric residence times of continental aerosols

    International Nuclear Information System (INIS)

    Balkanski, Y.J.

    1991-01-01

    The global atmospheric distributions of Rn-222 are simulated with a three-dimensional model of atmospheric transport based on the meteorology of the NASA Goddard Institute for Space Studies (GISS) general circulation model. The short-lived radioactive gas Rn-222 (half-life = 3.8d) is emitted almost exclusively from land, at a relatively uniform rate; hence it is an excellent tracer of continental influences. Lead-210 is produced by decay of Rn-222 and immediately condenses to preexisting aerosol surfaces. It provides an excellent measure of aerosol residence times in the atmosphere because its source is accurately defined by the Rn-222 distribution. Results from the three-dimensional model are compared to measurements of Rn-222 and Pb-210 atmospheric concentrations to evaluate model's long-range transport over oceanic regions and to study the deposition mechanisms of atmospheric aerosols. Model results for Rn-222 are used to examine the long-range transport of continental air over two selected oceanic regions, the subantarctic Indian Ocean and the North Pacific. It is shown that the fast transport of air from southern Africa causes substantial continental pollution at southern mid-latitudes, a region usually regarded as pristine. Air over the North Pacific is heavily impacted by continental influences year round, but the altitude at which the transport occurs varies seasonally. Observations of aerosols at island sites, which are commonly used as diagnostics of continental influences, may be misleading because they do not account for influences at high altitude and because aerosols are efficiently scavenged by deposition during transport. The study of Pb-210 focuses on defining the residence times of submicron aerosols in the troposphere. Scavenging in wet convective updrafts is found to provide the dominant sink on a global scale

  11. Effects of Structure and Hydrodynamics on the Sooting Behavior of Spherical Microgravity Diffusion Flames

    Science.gov (United States)

    Sunderland, P. B.; Axelbaum, R. L.; Urban, D. L.

    1999-01-01

    Recent experimental, numerical and analytical work has shown that the stoichiometric mixture fraction (Z(sub st)) can have a profound effect on soot formation in diffusion flames. These findings were obtained at constant flame temperature (T(sub ad)), employing the approach described in Du and Axelbaum (1995, 1996). For example, a fuel mixture containing 1 mole of ethylene and 11.28 moles of nitrogen burning in pure oxygen ((Z(sub st)) = 0.78) has the same adiabatic flame temperature (2370 K) as that of pure ethylene burning in air ((Z(sub st)) = 0.064). An important finding of these works was that at sufficiently high (Z(sub st)), flames remain blue as strain rate approaches zero in counterflow flames, or as flame height and residence time approach infinity in coflowing flames. Lin and Faeth (1996a) coined the term permanently blue to describe such flames. Two theories have been proposed to explain the appearance of permanently-blue flames at high (Z(sub st)). They are based on (1) hydrodynamics and (2) flame structure. Previous experimental studies in normal gravity are not definitive as to which, if either, mechanism is dominant because both hydrodynamics and structure suppress soot formation at high (Z(sub st)) in coflowing and counterflowing diffusion flames. In counterflow flames with (Z(sub st)) 0.5, convection at the flame is toward the oxidizer, thus enhancing soot oxidization. Thus, in counterflow flames, hydrodynamics causes soot to be convected towards the oxidizer at high (Z(sub st)) which suppresses soot formation. Axelbaum and co-workers maintain that while the direction of convection can impact soot growth and oxidation, these processes alone cannot cause permanently-blue flames. Soot growth and oxidation are dependent on the existence of soot particles and the presence of soot is invariably accompanied by yellow luminosity. Soot-particle inception, on the other hand, arises from gas-phase reactions and its dependence on flow direction is weak

  12. Prolonged and tunable residence time using reversible covalent kinase inhibitors.

    Science.gov (United States)

    Bradshaw, J Michael; McFarland, Jesse M; Paavilainen, Ville O; Bisconte, Angelina; Tam, Danny; Phan, Vernon T; Romanov, Sergei; Finkle, David; Shu, Jin; Patel, Vaishali; Ton, Tony; Li, Xiaoyan; Loughhead, David G; Nunn, Philip A; Karr, Dane E; Gerritsen, Mary E; Funk, Jens Oliver; Owens, Timothy D; Verner, Erik; Brameld, Ken A; Hill, Ronald J; Goldstein, David M; Taunton, Jack

    2015-07-01

    Drugs with prolonged on-target residence times often show superior efficacy, yet general strategies for optimizing drug-target residence time are lacking. Here we made progress toward this elusive goal by targeting a noncatalytic cysteine in Bruton's tyrosine kinase (BTK) with reversible covalent inhibitors. Using an inverted orientation of the cysteine-reactive cyanoacrylamide electrophile, we identified potent and selective BTK inhibitors that demonstrated biochemical residence times spanning from minutes to 7 d. An inverted cyanoacrylamide with prolonged residence time in vivo remained bound to BTK for more than 18 h after clearance from the circulation. The inverted cyanoacrylamide strategy was further used to discover fibroblast growth factor receptor (FGFR) kinase inhibitors with residence times of several days, demonstrating the generalizability of the approach. Targeting of noncatalytic cysteines with inverted cyanoacrylamides may serve as a broadly applicable platform that facilitates 'residence time by design', the ability to modulate and improve the duration of target engagement in vivo.

  13. Residence time determination for adsorbent beds of different configurations

    Energy Technology Data Exchange (ETDEWEB)

    Otermat, J.E.; Wikoff, W.O.; Kovach, J.L.

    1995-02-01

    The residence time calculations of ASME AG-1 Code, Section FC, currently specify a screen surface area method, that is technically incorrect. Test data has been obtained on Type II adsorber trays of different configurations to establish residence time in the adsorber trays. These data indicate that the air volume/carbon volume ratio or the average screen area are more appropriate for the calculation of the residence time calculation than the currently used, smallest screen area basis.

  14. Residence time determination for adsorbent beds of different configurations

    International Nuclear Information System (INIS)

    Otermat, J.E.; Wikoff, W.O.; Kovach, J.L.

    1995-01-01

    The residence time calculations of ASME AG-1 Code, Section FC, currently specify a screen surface area method, that is technically incorrect. Test data has been obtained on Type II adsorber trays of different configurations to establish residence time in the adsorber trays. These data indicate that the air volume/carbon volume ratio or the average screen area are more appropriate for the calculation of the residence time calculation than the currently used, smallest screen area basis

  15. Elective time during dermatology residency: A survey of residents and program directors.

    Science.gov (United States)

    Uppal, Pushpinder; Shantharam, Rohini; Kaufmann, Tara Lynn

    2017-12-15

    Elective time during residency training provides residents with exposure to different subspecialties. This opportunity gives residents the chance tonurture growth in particular areas of interest and broaden their knowledge base in certain topics in dermatology by having the chance to work withexperts in the field. The purpose of this study was to assess the views of residency program directors and dermatology residents on the value of elective time through a cross sectional survey. An eight-questionIRB exempt survey was sent out to 113 residency program directors via email through the American Professors of Dermatology (APD) program director listserv. Program directors were asked to forward a separate set of 9 questions to their residents. The majority of programs that responded allowed for some elective time within their schedule, often duringthe PGY 4 (3rd year of dermatology training), but the amount of time allowed widely varied among many residency programs. Overall, residents and program directors agree that elective is important in residencytraining, but no standardization is established across programs.

  16. Long residence times - bad tracer tests?

    Science.gov (United States)

    Ghergut, Julia; Behrens, Horst; Sauter, Martin

    2015-04-01

    Tracer tests conducted at geothermal well doublets or triplets in the Upper Rhine Rift Valley [1] all face, with very few exceptions so far, one common issue: lack of conclusive tracer test results, or tracer signals still undetectable for longer than one or two years after tracer injection. While the reasons for this surely differ from site to site (Riehen, Landau, Insheim, Bruchsal, ...), its effects on how the usefulness of tracer tests is perceived by the non-tracer community are pretty much the same. The 'poor-signal' frustration keeps nourishing two major 'alternative' endeavours : (I) design and execute tracer tests in single-well injection-withdrawal (push-pull), 'instead of' inter-well flow-path tracing configurations; (II) use 'novel' tracer substances instead of the 'old' ones which have 'obviously failed'. Frustration experienced with most inter-well tracer tests in the Upper Rhine Rift Valley has also made them be regarded as 'maybe useful for EGS' ('enhanced', or 'engineered' geothermal systems, whose fluid RTD typically include a major share of values below one year), but 'no longer worthwhile a follow-up sampling' in natural, large-scale hydrothermal reservoirs. We illustrate some of these arguments with the ongoing Bruchsal case [2]. The inter-well tracer test conducted at Bruchsal was (and still is!) aimed at assessing inter-well connectivity, fluid residence times, and characterizing the reservoir structure [3]. Fluid samples taken at the geothermal production well after reaching a fluid turnover of about 700,000 m3 showed tracer concentrations in the range of 10-8 Minj per m3, in the liquid phase of each sample (Minj being the total quantity of tracer injected as a short pulse at the geothermal re-injection well). Tracer signals might actually be higher, owing to tracer amounts co-precipitated and/or adsorbed onto the solid phase whose accumulation in the samples was unavoidable (due to pressure relief and degassing during the very sampling

  17. Biomass Gasification Behavior in an Entrained Flow Reactor: Gas Product Distribution and Soot Formation

    DEFF Research Database (Denmark)

    Qin, Ke; Jensen, Peter Arendt; Lin, Weigang

    2012-01-01

    Biomass gasification and pyrolysis were studied in a laboratory-scale atmospheric pressure entrained flow reactor. Effects of operating parameters and biomass types on the syngas composition were investigated. In general, the carbon conversion during biomass gasification was higher than 90......% at the optimal conditions of 1400 °C with steam addition. The biomass carbon that was not converted to gas in the gasification process only appeared as soot particles in the syngas in all of the experiments, except for the two experiments performed at 1000 °C, where a very small amount of char was also left....... In comparison to pyrolysis, lower yields of soot, H2, and CO were produced during gasification. The yield of soot could be reduced by a longer residence time, larger feeder air flow, lower oxygen concentration, higher excess air ratio, higher steam/carbon ratio, and higher reactor temperature. Changes...

  18. Residence time modeling of hot melt extrusion processes.

    Science.gov (United States)

    Reitz, Elena; Podhaisky, Helmut; Ely, David; Thommes, Markus

    2013-11-01

    The hot melt extrusion process is a widespread technique to mix viscous melts. The residence time of material in the process frequently determines the product properties. An experimental setup and a corresponding mathematical model were developed to evaluate residence time and residence time distribution in twin screw extrusion processes. The extrusion process was modeled as the convolution of a mass transport process described by a Gaussian probability function, and a mixing process represented by an exponential function. The residence time of the extrusion process was determined by introducing a tracer at the extruder inlet and measuring the tracer concentration at the die. These concentrations were fitted to the residence time model, and an adequate correlation was found. Different parameters were derived to characterize the extrusion process including the dead time, the apparent mixing volume, and a transport related axial mixing. A 2(3) design of experiments was performed to evaluate the effect of powder feed rate, screw speed, and melt viscosity of the material on the residence time. All three parameters affect the residence time of material in the extruder. In conclusion, a residence time model was developed to interpret experimental data and to get insights into the hot melt extrusion process. Copyright © 2013 Elsevier B.V. All rights reserved.

  19. The residence time of water in the atmosphere revisited

    NARCIS (Netherlands)

    Van Der Ent, Ruud J.; Tuinenburg, Obbe A.

    2017-01-01

    This paper revisits the knowledge on the residence time of water in the atmosphere. Based on state-of-the-art data of the hydrological cycle we derive a global average residence time of 8.9 ± 0.4 days (uncertainty given as 1 standard deviation). We use two different atmospheric moisture tracking

  20. Markov analysis for estimation of residence time | Agunwamba ...

    African Journals Online (AJOL)

    Accurate estimation of residence time is very useful for the design of water and wastewater treatment plants. Its determination is difficult because it depends on complex interaction among many factors such as geometry, hydrodynamic and environmental factors. In this paper, the estimation of residence time is formulated as ...

  1. Light changes the atmospheric reactivity of soot

    Science.gov (United States)

    D'Anna, Barbara; Monge, Maria-Eugenia; George, Christian; Ammann, Markus; Donaldson, D. Jamie

    2010-05-01

    conversion of NO2 to HONO leads to persistent reactivity over long times (7 hours). Uptake coefficients increased linearly with the irradiation intensity indicating that the number of reactive sites at the soot surface is proportional to the number of photoactivated species. We suggest that nitrogen-containing organic compounds are also produced on the soot surface as a consequence of the heterogeneous reaction with NO2 under irradiation. These compounds can then be photolyzed and release NO and HONO in a NOx-free atmosphere. An estimation of the HONO production rate indicates that heterogeneous soot photochemistry may contribute to the daytime HONO concentration (1). When soot particles are exposed to high concentrations of O3 under irradiation there is an increase in hydrophobicity as it was previously observed for organic surface films(2). (1)ME Monge, B D'Anna, L Mazri, A Giroir-Fendler, M Ammann, D. J. Donaldson, and C George. Light changes the atmospheric reactivity of soot. PNAS, 2010, doi:10.1073/ pnas.0908341107 In press (2)L Nieto-Gligorovski, S Net, S Gligorovski, C Zetzsch, A Jammoul, B D'Anna, C George. Interactions of ozone with organic surface films in the presence of simulated sunlight: impact on wettability of aerosols. Physical Chemistry Chemical Physics 10, 2008, 2964-2971.

  2. DNA residence time is a regulatory factor of transcription repression.

    Science.gov (United States)

    Clauß, Karen; Popp, Achim P; Schulze, Lena; Hettich, Johannes; Reisser, Matthias; Escoter Torres, Laura; Uhlenhaut, N Henriette; Gebhardt, J Christof M

    2017-11-02

    Transcription comprises a highly regulated sequence of intrinsically stochastic processes, resulting in bursts of transcription intermitted by quiescence. In transcription activation or repression, a transcription factor binds dynamically to DNA, with a residence time unique to each factor. Whether the DNA residence time is important in the transcription process is unclear. Here, we designed a series of transcription repressors differing in their DNA residence time by utilizing the modular DNA binding domain of transcription activator-like effectors (TALEs) and varying the number of nucleotide-recognizing repeat domains. We characterized the DNA residence times of our repressors in living cells using single molecule tracking. The residence times depended non-linearly on the number of repeat domains and differed by more than a factor of six. The factors provoked a residence time-dependent decrease in transcript level of the glucocorticoid receptor-activated gene SGK1. Down regulation of transcription was due to a lower burst frequency in the presence of long binding repressors and is in accordance with a model of competitive inhibition of endogenous activator binding. Our single molecule experiments reveal transcription factor DNA residence time as a regulatory factor controlling transcription repression and establish TALE-DNA binding domains as tools for the temporal dissection of transcription regulation. © The Author(s) 2017. Published by Oxford University Press on behalf of Nucleic Acids Research.

  3. Experimental determination of residence time distribution in continuous dry granulation.

    Science.gov (United States)

    Mangal, Haress; Kleinebudde, Peter

    2017-05-30

    With increasing importance of continuous manufacturing, the interest in integrating dry granulation into a continuous manufacturing line is growing. Residence time distribution measurements are of importance as they provide information about duration of materials within the process. These data enable traceability and are highly beneficial for developing control strategies. A digital image analysis system was used to determine the residence time distribution of two materials with different deformation behavior (brittle, plastic) in the milling unit of dry granulation systems. A colorant was added to the material (20%w/w iron oxide), which did not affect the material properties excessively, so the milling process could be mimicked well. Experimental designs were conducted to figure out which parameters effect the mean residence time strongly. Moreover, two types of dry granulation systems were contrasted. Longer mean residence times were obtained for the oscillating mill (OM) compared to the conical mill (CM). For co-processed microcrystalline cellulose residence times of 19.8-44.4s (OM) and 11.6-29.1s (CM) were measured, mainly influenced by the specific compaction force, the mill speed and roll speed. For dibasic calcium phosphate anhydrate residence times from 17.7-46.4 (OM) and 5.4-10.2s (CM) were measured, while here the specific compaction force, the mill speed and their interactions with the roll speed had an influence on the mean residence time. Copyright © 2017 Elsevier B.V. All rights reserved.

  4. Prediction of residence time distributions in food processing machinery

    DEFF Research Database (Denmark)

    Karlson, Torben; Friis, Alan; Szabo, Peter

    1996-01-01

    The velocity field in a co-rotating disc scraped surface heat exchanger (CDHE) is calculated using a finite element method. The residence time distribution for the CDHE is then obtained by tracing particles introduced in the inlet....

  5. Children's postdivorce residence arrangements and parental experienced time pressure

    NARCIS (Netherlands)

    van der Heijden, Franciëlla; Poortman, Anne Rigt; van der Lippe, Tanja

    2016-01-01

    Although the rise in postdivorce joint physical custody has fueled scholarly interest in its impact on children, consequences for parents remain understudied. Because children's residence arrangements determine time and coordination demands associated with child care, this study investigated the

  6. Residence time distribution studies on water-softening reactors

    International Nuclear Information System (INIS)

    Baranyai, L.

    1989-01-01

    Based on radiotracer techniques residence time distribution (RTD) studies were carried out on a water-softening reactor consisting of three physically separated units in order to characterize its hydrodynamical behaviour. The measured RTD curves and the actual mean residence times were compared with the theoretical values set up by modelling the reactor as a hydrodynamical system. Neither mixing nor sedimentation reaches ideal flow. The flow type in the settling cylinder is far of that what is expected. (author)

  7. Prediction of residence time distributions in food processing machinery

    DEFF Research Database (Denmark)

    Karlson, Torben; Friis, Alan; Szabo, Peter

    1996-01-01

    The velocity field in a co-rotating disc scraped surface heat exchanger (CDHE) is calculated using a finite element method. The residence time distribution for the CDHE is then obtained by tracing particles introduced in the inlet.......The velocity field in a co-rotating disc scraped surface heat exchanger (CDHE) is calculated using a finite element method. The residence time distribution for the CDHE is then obtained by tracing particles introduced in the inlet....

  8. Characterization of Air Plane Soot Surrogates using Raman spectroscopy and laser ablation techniques

    Science.gov (United States)

    Chazallon, Bertrand; Ortega, Ismael Kenneth; Ikhenazene, Raouf; Pirim, Claire; Carpentier, Yvain; Irimiea, Cornelia; Focsa, Cristian; Ouf, François-Xavier

    2016-04-01

    Aviation alters the composition of the atmosphere globally and can thus drive climate change and ozone depletion [1]. Aircraft exhaust plumes contain species (gases and soot particles) produced by the combustion of kerosene with ambient air in the combustion chamber of the engine. Soot particles emitted by air-planes produce persistent contrails in the upper troposphere in ice-supersaturated air masses that contribute to cloudiness and impact the radiative properties of the atmosphere. These aerosol-cloud interactions represent one of the largest sources of uncertainty in global climate models [2]. Though the formation of atmospheric ice particles has been studied for many years [3], there are still numerous opened questions on nucleation properties of soot particles [4], as the ice nucleation experiments showed a large spread in results depending on the nucleation mode chosen and origin of the soot produced. The reasons behind these discrepancies reside in the different physico-chemical properties (composition, structure) of soot particles produced in different conditions, e.g., with respect to fuel or combustion techniques. In this work, we use Raman microscopy (514 and 785 nm excitation wavelengths) and ablation techniques (Secondary Ions Mass Spectrometry, and Laser Desorption Mass Spectrometry) to characterize soot particle surrogates produced from a CAST generator (propane fuel, four different global equivalence ratios). They are produced as analogues of air-plane soot collected at different engine regimes (PowerJet SaM-146 turbofan) simulating a landing and take-off (LTO) cycle (MERMOSE project (http://mermose.onera.fr/)) [6]. The spectral parameters of the first-order Raman bands of these soot samples are analyzed using a de-convolution approach described by Sadezky et al. (2005) [5]. A systematic Raman analysis is carried out to select a number of parameters (laser wavelength, irradiance at sample, exposure time) that will alter the sample and the

  9. NATO Workshop on Soot in Combustion Systems

    CERN Document Server

    Prado, G

    1983-01-01

    Our interest in Mulhouse for carbon black and soot began some 30 years ago when J.B. Donnet developed the concept of surface chemistry of carbon and its involvement in interactions with gas, liquid and solid phases. In the late sixties, we began to study soot formation in pyrolytic systems and later on in flames. The idea of organ1z1ng a meeting on soot formation originated some four or five years ago, through discussions among Professor J.B. Howard, Dr. A. D'Alessio and ourselves. At that time the scientific community was becoming aware of the necessity to strictly control soot formation and emission. Being involved in the study of surface properties of carbon black as well as of formation of soot, we realized that the combustion community was not always fully aware of the progress made by the physical-chemists on carbon black. Reciprocally, the carbon specialists were often ignoring the research carried out on soot in flames. One objective of this workshop was to stimulate discussions between these two scie...

  10. Residents' perception of skill decay during dedicated research time.

    Science.gov (United States)

    D'Angelo, Anne-Lise D; Ray, Rebecca D; Jenewein, Caitlin G; Jones, Grace F; Pugh, Carla M

    2015-11-01

    Surgery residents may take years away from clinical responsibilities for dedicated research time. As part of a longitudinal project, the study aim was to investigate residents' perceptions of clinical skill reduction during dedicated research time. Our hypothesis was that residents would perceive a greater potential reduction in skill during research time for procedures they were less confident in performing. Surgical residents engaged in dedicated research training at multiple training programs participated in four simulated procedures: urinary catheterization, subclavian central line, bowel anastomosis, and laparoscopic ventral hernia (LVH) repair. Using preprocedure and postprocedure surveys, participants rated procedures for confidence and difficulty. Residents also indicated the perceived level of skills reduction for the four procedures as a result of time in the laboratory. Thirty-eight residents (55% female) completed the four clinical simulators. Participants had between 0-36 mo in a laboratory (M = 9.29 mo, standard deviation = 9.38). Preprocedure surveys noted lower confidence and higher perceived difficulty for performing the LVH repair followed by bowel anastomosis, central line insertion, and urinary catheterization (P perception for urinary catheterization (P perception and may provide a mechanism for maintaining skills and keeping confidence grounded in experience. Copyright © 2015 Elsevier Inc. All rights reserved.

  11. Halogen-aromatic π-interactions modulate inhibitor residence time.

    Science.gov (United States)

    Heroven, Christina; Georgi, Victoria; Ganotra, Gaurav K; Brennan, Paul E; Wolfreys, Finn; Wade, Rebecca C; Fernández-Montalván, Amaury E; Chaikuad, Apirat; Knapp, Stefan

    2018-03-30

    Prolonged drug residence times may result in longer lasting drug efficacy, improved pharmacodynamic properties and "kinetic selectivity" over off-targets with fast drug dissociation rates. However, few strategies have been elaborated to rationally modulate drug residence time and thereby to integrate this key property into the drug development process. Here, we show that the interaction between a halogen moiety on an inhibitor and an aromatic residue in the target protein can significantly increase inhibitor residence time. By using the interaction of the serine/threonine kinase haspin with 5-iodotubercidin (5-iTU) derivatives as a model for an archetypal active state (type I) kinase-inhibitor binding mode, we demonstrate that inhibitor residence times markedly increase with the size and polarizability of the halogen atom. This key interaction is dependent on the interactions with an aromatic residue in the gatekeeper position and we observe this interaction in other kinases with an aromatic gatekeeper residue. We provide a detailed mechanistic characterization of the halogen-aromatic π interactions in the haspin-inhibitor complexes by means of kinetic, thermodynamic, and structural measurements along with binding energy calculations. Since halogens are frequently used in drugs and aromatic residues are often present in the binding sites of proteins, our results provide a compelling rationale for introducing aromatic-halogen interactions to prolong drug-target residence times. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  12. Soot Surface Growth in Laminar Hydrocarbon/Air Diffusion Flames. Appendix B

    Science.gov (United States)

    El-Leathy, A. M.; Xu, F.; Kim, C. H.; Faeth, G. M.; Urban, D. L. (Technical Monitor); Yuan, Z.-G. (Technical Monitor)

    2001-01-01

    The structure and soot surface growth properties of round laminar jet diffusion flames were studied experimentally. Measurements were made along the axes of ethylene-, propylene-propane- and acetylene-benzene-fueled flames burning in coflowing air at atmospheric pressure with the reactants at normal temperature. The measurements included soot structure, soot concentrations, soot temperatures, major gas species concentrations, some radial species (H, OH and O) concentrations, and gas velocities. These measurements yielded the local flame properties that are thought to affect soot surface growth as well as local soot surface growth rates. When present results were combined with similar earlier observations of acetylene-fueled laminar jet diffusion flames, the results suggested that soot surface growth involved decomposition of the original fuel to form acetylene and H, which were the main reactants for soot surface growth, and that the main effect of the parent fuel on soot surface growth involved its yield of acetylene and H for present test conditions. Thus, as the distance increased along the axes of the flames, soot formation (which was dominated by soot surface growth) began near the cool core of the flow once acetylene and H appeared together and ended near the flame sheet when acetylene disappeared. Species mainly responsible for soot oxidation - OH and O2 were present throughout the soot formation region so that soot surface growth and oxidation proceeded at the same time. Present measurements of soot surface growth rates (corrected for soot surface oxidation) in laminar jet diffusion flames were consistent with earlier measurements of soot surface growth rates in laminar premixed flames and exhibited good agreement with existing Hydrogen-Abstraction/Carbon-Addition (HACA) soot surface growth mechanisms in the literature with steric factors in these mechanisms having values on the order of unity, as anticipated.

  13. Soot Surface Growth in Laminar Hydrocarbon/Air Diffusion Flames. Appendix J

    Science.gov (United States)

    El-Leathy, A. M.; Xu, F.; Kim, C. H.; Faeth, G. M.; Yuan, Z.-G. (Technical Monitor); Urban, D. L. (Technical Monitor); Yuan, Z.-G. (Technical Monitor)

    2003-01-01

    The structure and soot surface growth properties of round laminar jet diffusion flames were studied experimentally. Measurements were made along the axes of ethylene-, propylene-propane- and acetylene-benzene-fueled flames burning in coflowing air at atmospheric pressure with the reactants at normal temperature. The measurements included soot structure, soot concentrations, soot temperatures, major gas species concentrations, some radial species (H, OH and 0) concentrations, and gas velocities. These measurements yielded the local flame properties that are thought to affect soot surface growth as well as local soot surface growth rates. When present results were combined with similar earlier observations of acetylene-fueled laminar jet diffusion flames, the results suggested that soot surface growth involved decomposition of the original fuel to form acetylene and H, which were the main reactants for soot surface growth, and that the main effect of the parent fuel on soot surface growth involved its yield of acetylene and H for present test conditions. Thus, as the distance increased along the axes of the flames, soot formation (which was dominated by soot surface growth) began near the cool core of the flow once acetylene and H appeared together and ended near the flame sheet when acetylene disappeared. Species mainly responsible for soot oxidation - OH and 02 were present throughout the soot formation region so that soot surface growth and oxidation proceeded at the same time. Present measurements of soot surface growth rates (corrected for soot surface oxidation) in laminar jet diffusion flames were consistent with earlier measurements of soot surface growth rates in laminar premixed flames and exhibited good agreement with existing Hydrogen-Abstraction/Carbon-Addition (HACA) soot surface growth mechanisms in the literature with steric factors in these mechanisms having values on the order of unity, as anticipated.

  14. Real time curriculum map for internal medicine residency.

    Science.gov (United States)

    Wong, Roger Y; Roberts, J Mark

    2007-11-07

    To manage the voluminous formal curriculum content in a limited amount of structured teaching time, we describe the development and evaluation of a curriculum map for academic half days (AHD) in a core internal medicine residency program. We created a 3-year cyclical curriculum map (an educational tool combining the content, methodology and timetabling of structured teaching), comprising a matrix of topics under various specialties/themes and corresponding AHD hours. All topics were cross-matched against the ACP-ASIM in-training examination, and all hours were colour coded based on the categories of core competencies. Residents regularly updated the map on a real time basis. There were 208 topics covered in 283 AHD hours. All topics represented core competencies with minimal duplication (78% covered once in 3 years). Only 42 hours (15%) involved non-didactic teaching, which increased after implementation of the map (18-19 hours/year versus baseline 5 hours/year). Most AHD hours (78%) focused on medical expert competencies. Resident satisfaction (90% response) was high throughout (range 3.64 +/- 0.21, 3.84 +/- 0.14 out of 4), which improved after 1 year but returned to baseline after 2 years. We developed and implemented an internal medicine curriculum map based on real time resident input, with minimal topic duplication and high resident satisfaction. The map provided an opportunity to balance didactic versus non-didactic teaching, and teaching on medical versus non medical expert topics.

  15. Effect of oven residence time on mechanical properties in ...

    Indian Academy of Sciences (India)

    Simulation studies were conducted using ROTOSIM software to analyze thermal transitions and phase changes during the process. Degree of curing of the polymers was also assessed and correlated with mechanical properties. Experiments were further conducted to obtain favourable oven residence time to obtain highest ...

  16. Studies on steps affecting tritium residence time in solid blanket

    International Nuclear Information System (INIS)

    Tanaka, Satoru

    1987-01-01

    For the self sustaining of CTR fuel cycle, the effective tritium recovery from blankets is essential. This means that not only tritium breeding ratio must be larger than 1.0, but also high recovering speed is required for the short residence time of tritium in blankets. Short residence time means that the tritium inventory in blankets is small. In this paper, the tritium residence time and tritium inventory in a solid blanket are modeled by considering the steps constituting tritium release. Some of these tritium migration processes were experimentally evaluated. The tritium migration steps in a solid blanket using sintered breeding materials consist of diffusion in grains, desorption at grain edges, diffusion and permeation through grain boundaries, desorption at particle edges, diffusion and percolation through interconnected pores to purging stream, and convective mass transfer to stream. Corresponding to these steps, diffusive, soluble, adsorbed and trapped tritium inventories and the tritium in gas phase are conceivable. The code named TTT was made for calculating these tritium inventories and the residence time of tritium. An example of the results of calculation is shown. The blanket is REPUTER-1, which is the conceptual design of a commercial reversed field pinch fusion reactor studied at the University of Tokyo. The experimental studies on the migration steps of tritium are reported. (Kako, I.)

  17. Relationships between removal processes and residence times for atmospheric pollutants

    International Nuclear Information System (INIS)

    Slinn, W.G.N.

    1978-01-01

    This report is concerned with improving estimates for the residence times of atmospheric trace constituents in various atmospheric reservoirs. Residence times are defined only for steady-state conditions; i.e., when the net growth rate vanishes. The most useful case of vanishing net growth rate is when the total growth rate is equal to the decay rate. It is demonstrated that the most important advance towards improving estimates of pollutant residence times is through proper choices of reservoirs. Chosen reservoirs should possess the following features: steady-state conditions, uniform mixing ratio throughout or throughout specified subreservoirs, and subreservoirs chosen in which removal rates can be treated as approximate constants. An example of a poorly mixed reservoir, the stratosphere, is discussed. In another example, it is suggested that commonly used reservoirs for atmospheric CO 2 have been chosen poorly and that a substantial portion of the anthropogenic CO 2 released during the past 50 years may still be mixing into the stratosphere. In another example, it is suggested that determination of the dry deposition velocity for accumulation-mode aerosol particles may not be so important as previously thought. To improve estimates for the atmospheric residence times of these particles, it is important to increase knowledge of what is called the ascension velocity

  18. Effect of oven residence time on mechanical properties in ...

    Indian Academy of Sciences (India)

    In rotational moulding of plastics, improving the mechanical properties without sacrificing the processibility is a challenging task. In this paper, an attempt has been made to investigate the effect of oven residence time on the mechanical properties of the rotationally moulded products made using linear low ...

  19. Financial and Time Burdens for Medical Students Interviewing for Residency.

    Science.gov (United States)

    Callaway, Paul; Melhado, Trisha; Walling, Anne; Groskurth, Jordan

    2017-02-01

    Interviewing for residency positions is increasingly stressful for students and challenging for programs. Little information is available about the costs and time invested by students in interviewing or about the key factors in decisions to accept interview offers. Our objective was to assess the time and financial costs of residency interviewing for an entire class at a regional campus and explore factors influencing student decisions to accept interviews. We used a 14-item survey administered electronically immediately following National Resident Matching Program results. The response rate was 75% (49 of 65 students). About half interviewed in primary care specialties. Thirty students (63%) applied to 20 or more programs, and 91% were offered multiple interviews out of state. Seventy percent limited interviews by time and cost. Other important factors included personal "fit," program reputation, and the quality of residents. About 50% of the students spent more than 20 days and $1,000-$5,000 interviewing; 29% reported spending over $5,000. Students used multiple funding sources, predominantly loans and savings. Primary care applicants applied to fewer out-of-state programs, reported fewer interview days and lower expenses, but received more financial support from programs. Students invested considerable time and resources in interviewing, and these factors significantly influenced their decisions about accepting interviews. The other major factors in interview decisions concerned personal comfort with the program, especially the residents. The costs and time reported in this study could be greater than other schools due to the regional campus location or lower due to the high proportion of students interviewing in primary care.

  20. Modeling the Residence Time of Mobile Bay in Alabama

    Science.gov (United States)

    Han, M. M.; Park, K.

    2016-02-01

    The Three-dimensional Hydrodynamic-Eutrophication Model/Environmental Fluid Dynamics Code (HEM3D/EFDC) was used to calculate the residence time of Mobile Bay in Alabama using Eulerian passive tracer method. Mobile Bay is about 50 km long and 20 km wide, so it can be divided into several sections which may have different residence times. Three typical boundary conditions that affect residence time are tide, river discharge, and wind. Mobile Bay is located in the northern Gulf of Mexico and is a micro-tidal region. Two most important tidal components here are K1 and O1, and the maximum tidal range of tropic (spring) tide is less than 0.6 m. There is a difference between the simulation results with and without tidal condition (K1+O1) even though the tidal range is relatively smaller than that in macro-tidal regions. Also the minimum, mean, and maximum of daily mean river discharge for 38 years (1976-2013) in Mobile and Tensaw River are 80.7 m3/s, 1700.8 m3/s, and 14186.7 m3/s respectively, and there are daily, monthly, seasonal, and annual variations. The residence time can be largely affected by the river discharge because of its large deviation. Even though the dominant wind here is southerly in the spring and summer and is northerly in the fall and winter, the wind speed and direction change over time. Continuous winds from similar directions can reduce and increase the residence time such as the southerly, southwesterly, northerly, and northeasterly winds in alignment with the direction of the inlet and outlet of Mobile Bay. Also the short term changes of wind direction and speed can affect it complicatedly. Therefore, the simulations with the combinations of three boundary conditions allow us to understand the water circulation in Mobile Bay well and to predict the residence time when some accidents happen such as contaminations by factories, sewage plants, ships and oil spills.

  1. Real time curriculum map for internal medicine residency

    Directory of Open Access Journals (Sweden)

    Roberts J Mark

    2007-11-01

    Full Text Available Abstract Background To manage the voluminous formal curriculum content in a limited amount of structured teaching time, we describe the development and evaluation of a curriculum map for academic half days (AHD in a core internal medicine residency program. Methods We created a 3-year cyclical curriculum map (an educational tool combining the content, methodology and timetabling of structured teaching, comprising a matrix of topics under various specialties/themes and corresponding AHD hours. All topics were cross-matched against the ACP-ASIM in-training examination, and all hours were colour coded based on the categories of core competencies. Residents regularly updated the map on a real time basis. Results There were 208 topics covered in 283 AHD hours. All topics represented core competencies with minimal duplication (78% covered once in 3 years. Only 42 hours (15% involved non-didactic teaching, which increased after implementation of the map (18–19 hours/year versus baseline 5 hours/year. Most AHD hours (78% focused on medical expert competencies. Resident satisfaction (90% response was high throughout (range 3.64 ± 0.21, 3.84 ± 0.14 out of 4, which improved after 1 year but returned to baseline after 2 years. Conclusion We developed and implemented an internal medicine curriculum map based on real time resident input, with minimal topic duplication and high resident satisfaction. The map provided an opportunity to balance didactic versus non-didactic teaching, and teaching on medical versus non medical expert topics.

  2. Mutagenicity of diesel exhaust soot dispersed in phospholipid surfactants

    Energy Technology Data Exchange (ETDEWEB)

    Wallace, W.; Keane, M.; Xing, S.; Harrison, J.; Gautam, M.; Ong, T.

    1994-06-01

    Organics extractable from respirable diesel exhaust soot particles by organic solvents have been known for some time to be direct acting frameshift mutagens in the Ames Salmonella typhimurium histidine reversion assay. Upon deposition in a pulmonary alveolus or respiratory bronchiole, respirable diesel soot particles will contact first the hypophase which is coated by and laden with surfactants. To model interactions of soot and pulmonary surfactant, the authors dispersed soots in vitro in the primary phospholipid pulmonary surfactant dipalmitoyl glycerophosphorylcholine (lecithin) (DPL) in physiological saline. They have shown that diesel soots dispersed in lecithin surfactant can express mutagenic activity, in the Ames assay system using S. typhimurium TA98, comparable to that expressed by equal amounts of soot extracted by dichloromethane/dimethylsulfoxide (DCM/DMSO). Here the authors report additional data on the same system using additional exhaust soots and also using two other phospholipids, dipalmitoyl glycerophosphoryl ethanolamine (DPPE), and dipalmitoyl phosphatidic acid (DPPA), with different ionic character hydrophilic moieties. A preliminary study of the surfactant dispersed soot in an eucaryotic cell test system also is reported.

  3. LES of Sooting Flames

    Science.gov (United States)

    2006-12-01

    investigated the formation of carbon in a well-stirred reactor. The critical C/O ratio for soot inception was observed and compared to Bunsen -Type flames ...The computations reproduced the flame structure, with reasonable agreement of the velocity field. They designed the swirl burner to match the...the vortex breakdown. 121 [203] introduced the compositional structure and flow field of two flames on the same burner . The two flames have the same

  4. Soot, organics, and ultrafine ash from air- and oxy-fired coal combustion

    KAUST Repository

    Andersen, Myrrha E.

    2016-10-19

    Pulverized bituminous coal was burned in a 10. W externally heated entrained flow furnace under air-combustion and three oxy-combustion inlet oxygen conditions (28, 32, and 36%). Experiments were designed to produce flames with practically relevant stoichiometric ratios (SR. =1.2-1.4) and constant residence times (2.3. s). Size-classified fly ash samples were collected, and measurements focused on the soot, elemental carbon (EC), and organic carbon (OC) composition of the total and ultrafine (<0.6. μm) fly ash. Results indicate that although the total fly ash carbon, as measured by loss on ignition, was always acceptably low (<2%) with all three oxy-combustion conditions lower than air-combustion, the ultrafine fly ash for both air-fired and oxy-fired combustion conditions consists primarily of carbonaceous material (50-95%). Carbonaceous components on particles <0.6. μm measured by a thermal optical method showed that large fractions (52-93%) consisted of OC rather than EC, as expected. This observation was supported by thermogravimetric analysis indicating that for the air, 28% oxy, and 32% oxy conditions, 14-71% of this material may be OC volatilizing between 100. C and 550. C with the remaining 29-86% being EC/soot. However, for the 36% oxy condition, OC may comprise over 90% of the ultrafine carbon with a much smaller EC/soot contribution. These data were interpreted by considering the effects of oxy-combustion on flame attachment, ignition delay, and soot oxidation of a bituminous coal, and the effects of these processes on OC and EC emissions. Flame aerodynamics and inlet oxidant composition may influence emissions of organic hazardous air pollutants (HAPs) from a bituminous coal. During oxy-coal combustion, judicious control of inlet oxygen concentration and placement may be used to minimize organic HAP and soot emissions.

  5. Mean Residence Time and Emergency Drinking Water Supply.

    Science.gov (United States)

    Kralik, Martin; Humer, Franko

    2013-04-01

    Immediately after securing an endangered population, the first priority of aid workers following a disaster is the distribution of drinking water. Such emergency situations are reported from many parts of the world following regional chemical or nuclear pollution accidents, floods, droughts, rain-induced landslides, tsunami, and other extreme events. It is often difficult to organise a replacement water supply when regular water systems with short residence times are polluted, infiltrated or even flooded by natural or man-made disasters. They are either unusable or their restoration may take months or even years. Groundwater resources, proven safe and protected by the geological environment, with long residence times and the necessary infrastructure for their exploitation, would provide populations with timeous replacement of vulnerable water supply systems and make rescue activities more rapid and effective. Such resources have to be identified and investigated, as a substitute for affected drinking water supplies thereby eliminating or reducing the impact of their failure following catastrophic events. Even in many areas such water resources with long residence times in years or decades are difficult to find it should be known which water supply facilities in the region are matching these requirements to allow in emergency situation the transport of water in tankers to the affected regions to prevent epidemics, importing large quantities of bottled water. One should know the residence time of the water supply to have sufficient time to plan and install new safe water supply facilities. Development of such policy and strategy for human security - both long term and short term - is therefore needed to decrease the vulnerability of populations threatened by extreme events and water supplies with short residence times. Generally: The longer the residence time of groundwater in the aquifer, the lower its vulnerability. The most common and economic methods to estimate

  6. Computational Investigation of Soot and Radiation in Turbulent Reacting Flows

    Science.gov (United States)

    Lalit, Harshad

    This study delves into computational modeling of soot and infrared radiation for turbulent reacting flows, detailed understanding of both of which is paramount in the design of cleaner engines and pollution control. In the first part of the study, the concept of Stochastic Time and Space Series Analysis (STASS) as a numerical tool to compute time dependent statistics of radiation intensity is introduced for a turbulent premixed flame. In the absence of high fidelity codes for large eddy simulation or direct numerical simulation of turbulent flames, the utility of STASS for radiation imaging of reacting flows to understand the flame structure is assessed by generating images of infrared radiation in spectral bands dominated by radiation from gas phase carbon dioxide and water vapor using an assumed PDF method. The study elucidates the need for time dependent computation of radiation intensity for validation with experiments and the need for accounting for turbulence radiation interactions for correctly predicting radiation intensity and consequently the flame temperature and NOx in a reacting fluid flow. Comparison of single point statistics of infrared radiation intensity with measurements show that STASS can not only predict the flame structure but also estimate the dynamics of thermochemical scalars in the flame with reasonable accuracy. While a time series is used to generate realizations of thermochemical scalars in the first part of the study, in the second part, instantaneous realizations of resolved scale temperature, CO2 and H2O mole fractions and soot volume fractions are extracted from a large eddy simulation (LES) to carry out quantitative imaging of radiation intensity (QIRI) for a turbulent soot generating ethylene diffusion flame. A primary motivation of the study is to establish QIRI as a computational tool for validation of soot models, especially in the absence of conventional flow field and measured scalar data for sooting flames. Realizations of

  7. The residence time of intensively managed agricultural landscapes

    Science.gov (United States)

    Bowling, Laura; Cherkauer, Keith; Chiu, Chun-mei; Rahman, Sanoar

    2015-04-01

    Much of the agricultural landscape across the Midwestern United States is intensively managed through numerous surface and subsurface drainage improvements, and the growing extraction of groundwater resources. The relatively recent glaciation of the North Central region means that the landscape is less dissected and hydrologically connected than older till areas. Low topographic gradients and underlying dense till which restricts vertical water movement, as well as kettle depressions, have led to poorly drained soils and extensive wetlands within the landscape. Large areas of this land could only be farmed once the excess water was removed through artificial surface and subsurface drainage. Conventional wisdom in the region maintains that subsurface tile drainage reduces the occurrence of peak flow events by increasing soil water storage capacity. At the watershed scale, this view does not take into account the coincident increase in surface drainage and reduction in residence time in surface depressions. This paper explores to what degree water management and irrigation has changed surface and subsurface water storage and residence time over the last century and how this has impacted flow duration throughout the Wabash River system in Indiana, USA. The effects of subsurface tile drains, wetlands and aquifer storage are explicitly represented within the Variable Infiltration Capacity (VIC) macroscale hydrology model. We maintain a focus on the entire Wabash River, a river system of historic importance that is also representative of many similar areas in the till plain region of the agricultural Midwest, which contribute to water quality and flood dynamics of the Mississippi river system. By lowering the water table, surface and subsurface drainage improvements have increased the subsurface storage capacity at the beginning of rain events, but this is overwhelmed by the decrease in surface storage capacity for intermediate to large events, decreasing the current

  8. Modelling travel and residence times in the eastern Irish Sea

    International Nuclear Information System (INIS)

    Dabrowski, T.; Hartnett, M.

    2008-01-01

    The Irish Sea, which lies between 51 deg. N-56 deg. N and 2 deg. 50'W-7 deg. W, provides a sheltered environment to exploit valuable fisheries resource. Anthropogenic activity is a real threat to its water quality. The majority of freshwater input down rivers flows into the eastern Irish Sea. The structure of the water circulation was not well understood during the planning of Sellafield nuclear plant outfall site in the eastern Irish Sea. A three-dimensional primitive equation numerical model was applied to the Irish Sea to simulate both barotropic and baroclinic circulation within the region. High accuracy was achieved with regard to the prediction of both tidal circulation and surface and nearbed water temperatures across the region. The model properly represented the Western Irish Sea Gyre, induced by thermal stratification and not known during planning Sellafield. Passive tracer simulations based on the developed hydrodynamic model were used to deliver residence times of the eastern Irish Sea region for various times of the year as well as travel times from the Sellafield outfall site to various locations within the Irish Sea. The results indicate a strong seasonal variability of travel times from Sellafield to the examined locations. Travel time to the Clyde Sea is the shortest for the autumnal tracer release (90 days); it takes almost a year for the tracer to arrive at the same location if it is released in January. Travel times from Sellafield to Dublin Bay fall within the range of 180-360 days. The average residence time of the entire eastern Irish Sea is around 7 months. The areas surrounding the Isle of Man are initially flushed due to a predominant northward flow; a backwater is formed in Liverpool Bay. Thus, elevated tracer concentrations are predicted in Liverpool Bay in the case of accidental spills at the Sellafield outfall site

  9. Water interaction with hydrophobic and hydrophilic soot particles.

    Science.gov (United States)

    Popovicheva, Olga; Persiantseva, Natalia M; Shonija, Natalia K; DeMott, Paul; Koehler, Kirsten; Petters, Markus; Kreidenweis, Sonia; Tishkova, Victoria; Demirdjian, Benjamin; Suzanne, Jean

    2008-05-07

    The interaction of water with laboratory soots possessing a range of properties relevant for atmospheric studies is examined by two complementary methods: gravimetrical measurement of water uptake coupled with chemical composition and porosity analysis and HTDMA (humidified tandem differential mobility analyzer) inference of water uptake accompanied by separate TEM (transmission electron microscopy) analysis of single particles. The first method clarifies the mechanism of water uptake for bulk soot and allows the classification of soot with respect to its hygroscopicity. The second method highlights the dependence of the soot aerosol growth factor on relative humidity (RH) for quasi-monodisperse particles. Hydrophobic and hydrophilic soot are qualitatively defined by their water uptake and surface polarity: laboratory soot particles are thus classified from very hydrophobic to very hydrophilic. Thermal soot particles produced from natural gas combustion are classified as hydrophobic with a surface of low polarity since water is found to cover only half of the surface. Graphitized thermal soot particles are proposed for comparison as extremely hydrophobic and of very low surface polarity. Soot particles produced from laboratory flame of TC1 aviation kerosene are less hydrophobic, with their entire surface being available for statistical monolayer water coverage at RH approximately 10%. Porosity measurements suggest that, initially, much of this surface water resides within micropores. Consequently, the growth factor increase of these particles to 1.07 at RH > 80% is attributed to irreversible swelling that accompanies water uptake. Hysteresis of adsorption/desorption cycles strongly supports this conclusion. In contrast, aircraft engine soot, produced from burning TC1 kerosene in a gas turbine engine combustor, has an extremely hydrophilic surface of high polarity. Due to the presence of water soluble organic and inorganic material it can be covered by many water

  10. The determination of residence times in a pilot plant

    Science.gov (United States)

    Ramírez, F. Pablo; Cortés, M. Eugenia

    2004-01-01

    It is well known that residence time distributions (RTD) are very important in many chemical processes such as separation, reforming, hydrocracking, fluid catalytic cracking, hydrodesulfuration, hydrogenation among others [3 Procédés de transformation, Editions Technip, Institute Francais du Petrole, Paris, France, 1998]. In addition, tracers can be used to measure the velocity, distribution and residence time of any stream through any part of an industrial [Guidebook on Radioisotope Tracers in Industry, IAEA, Vienna, 1990] or experimental system. Perhaps the best quality of radiotracers is that they do not interfere with normal unit operations or production scheduling. In this paper are presented the RTDs obtained in a pilot plant for a hydrogenation process [IMP, Technical Report, Determinación del tiempo de residencia promedio en el reactor de la planta piloto de hidroagotamiento de crudo, 2002]. The RTDs show a random phenomenon, which is not typical of this type of chemical processes. Several RTDs were determined in order to confirm this random behavior. The data were obtained using as a tracer a radioactive form of sodium iodide containing iodine-131 [The Condensed Chemical Dictionary, 10th Ed., Van Nostrand Reinhold, USA, 1981]. The process works with two phases in a countercurrent flow, inside a packed column. The liquid phase goes down by gravity. The gas phase goes up due to pressure difference [3 Procédés de transformation, Editions Technip, Institute Francais du Petrole, Paris, France, 1998]. The tracer was selected such that it would follow the liquid phase.

  11. Residence Times in Central Valley Aquifers Recharged by Dammed Rivers

    Science.gov (United States)

    Loustale, M.; Paukert Vankeuren, A. N.; Visser, A.

    2017-12-01

    Groundwater is a vital resource for California, providing between 30-60% of the state's water supply. Recent emphasis on groundwater sustainability has induced a push to characterize recharge rates and residence times for high priority aquifers, including most aquifers in California's Central Valley. Flows in almost all rivers from the western Sierra to the Central Valley are controlled by dams, altering natural flow patterns and recharge to local aquifers. In eastern Sacramento, unconfined and confined shallow aquifers (depth BGS. Variation in groundwater age in the vertical and horizontal directions are used to determine groundwater flow path and velocity. These data are then used to calculate residence time of groundwater in the unconfined and confined aquifer systems for the Central Valley in eastern Sacramento. Applying groundwater age tracers can benefit future compliance metrics of the California Sustainable Groundwater Resources Act (SGMA), by quantifying river seepage rates and impacts of groundwater management on surface water resources. 1Moran et al., UCRL-TR-203258, 2004.

  12. Classifying terrestrial surface water systems using integrated residence time

    Science.gov (United States)

    Jones, Allan; Hodges, Ben; McClelland, James; Hardison, Amber; Moffett, Kevan

    2017-04-01

    Linkages between ecology and hydrology in terrestrial surface water often invoke a discussion of lentic (reservoir) vs. lotic (riverine) system behaviors. However, the literature shows a wide range of thresholds separating lentic/lotic regimes and little agreement on a quantitative, repeatable classification metric that can be broadly and reliably applied across a range of systems hosting various flow regimes and suspended/benthic taxa. We propose an integrated Residence Time (iTR) metric as part of a new Freshwater Continuum Classification (FCC) to address this issue. The iTR is computed as the transit time of a water parcel across a system given observed temporal variations in discharge and volume, which creates a temporally-varying metric applicable across a defined system length. This approach avoids problems associated with instantaneous residence times or average residence times that can lead to misleading characterizations in seasonally- or episodically-dynamic systems. The iTR can be directly related to critical flow thresholds and timescales of ecology (e.g., zooplankton growth). The FCC approach considers lentic and lotic to be opposing end-members of a classification continuum and also defines intermediate regimes that blur the line between the two ends of the spectrum due to more complex hydrological system dynamics. We also discover the potential for "oscillic" behavior, where a system switches between lentic and lotic classifications either episodically or regularly (e.g., seasonally). Oscillic behavior is difficult to diagnose with prior lentic/lotic classification schemes, but can be readily identified using iTR. The FCC approach was used to analyze 15 tidally-influenced river segments along the Texas (USA) coast of the Gulf of Mexico. The results agreed with lentic/lotic designations using prior approaches, but also identified more nuanced intermediate and oscillic regimes. Within this set of systems, the oscillic nature of some of the river

  13. Mean Transit Time and Mean Residence Time for Linear Diffusion–Convection–Reaction Transport System

    Directory of Open Access Journals (Sweden)

    Jacek Waniewski

    2007-01-01

    Full Text Available Characteristic times for transport processes in biological systems may be evaluated as mean transit times (MTTs (for transit states or mean residence times (MRT (for steady states. It is shown in a general framework of a (linear reaction–diffusion–convection equation that these two times are related. Analytical formulas are also derived to calculate moments of exit time distribution using solutions for a stationary state of the system.

  14. Residence Time Distributions in a Cold, Confined Swirl Flow

    DEFF Research Database (Denmark)

    Lans, Robert Pieter Van Der; Glarborg, Peter; Dam-Johansen, Kim

    1997-01-01

    -burner zone of the laboratory furnace-model were studied. RTD results have been used to derive a chemical reaction engineering model for the mixing process. The model is based on a combination of plug flow reactors and continuous stirred tank reactors, which represent the main flow characteristics in regard......, well characterised flow pattern makes it possible to investigate the importance of mixing intensity on the (pollution) chemistry in furnaces. The reactor model developed here will be the basis for the development of a chemical reaction engineering combustion model.......Residence time distributions (RTD) in a confined, cold swirling flow have been measured with a fast-response probe and helium as a tracer. The test-rig represented a scaled down version of a burner. The effect of variation of flow velocities and swirl angle on the flow pattern in the near...

  15. Investigations of Sooting Laminar Coflow Diffusion Flames at Elevated Pressures

    KAUST Repository

    Steinmetz, Scott A.

    2016-12-01

    sizes plateau. Particle size in the annulus is more sensitive to pressure. Next, the development of an alternative particle size measuring technique is studied. Time Resolved Laser Induced Incandescence (TiRe-LII) is a commonly used technique to measure soot concentrations and particle size at atmospheric pressure. However, Laser Induced Incandescence (LII) models suffer from an incomplete understanding of the effects of elevated pressures on the absorption, annealing, and cooling of soot. The present study focuses on what affect the laser temporal pulse shape and duration may have on particle sizing. TiRe-LII in flames at 1 and 15 bar is carried out, using laser pulses with tophat or Gaussian temporal profiles of varying duration. Mono-disperse equivalent primary particle diameters are calculated using the KAUST LII model. Little difference in particle sizing is found for different laser pulses. However, this data will be useful for validating the KAUST LII model when absorption and poly-dispersion are accounted for. In an effort to move one step closer to logistical fuel studies, the sooting tendencies of a number of liquid fuels are studied at pressures up to 10. Of parallel relevance, a sooting index for surrogate development is evaluated for elevated pressure applications. The Yield Sooting Index (YSI) methodology is applied to 11 normal, cyclic, and branched alkanes. When referencing to two n-alkane fuels, the YSI of n-alkanes determined at atmospheric pressures accurately reflects the relative sooting tendencies of these fuels at elevated pressures. The relative sooting tendencies of cyclo- and methyl-alkanes have a lower pressure sensitivity than n-alkanes.

  16. On the formation and early evolution of soot in turbulent nonpremixed flames

    KAUST Repository

    Bisetti, Fabrizio

    2012-01-01

    A Direct Numerical Simulation (DNS) of soot formation in an n-heptane/air turbulent nonpremixed flame has been performed to investigate unsteady strain effects on soot growth and transport. For the first time in a DNS of turbulent combustion, Polycyclic Aromatic Hydrocarbons (PAH) are included via a validated, reduced chemical mechanism. A novel statistical representation of soot aggregates based on the Hybrid Method of Moments is used [M.E. Mueller, G. Blanquart, H. Pitsch, Combust. Flame 156 (2009) 1143-1155], which allows for an accurate state-of-the-art description of soot number density, volume fraction, and morphology of the aggregates. In agreement with previous experimental studies in laminar flames, Damköhler number effects are found to be significant for PAH. Soot nucleation and growth from PAH are locally inhibited by high scalar dissipation rate, thus providing a possible explanation for the experimentally observed reduction of soot yields at increasing levels of mixing in turbulent sooting flames. Furthermore, our data indicate that soot growth models that rely on smaller hydrocarbon species such as acetylene as a proxy for large PAH molecules ignore or misrepresent the effects of turbulent mixing and hydrodynamic strain on soot formation due to differences in the species Damköhler number. Upon formation on the rich side of the flame, soot is displaced relative to curved mixture fraction iso-surfaces due to differential diffusion effects between soot and the gas-phase. Soot traveling towards the flame is oxidized, and aggregates displaced away from the flame grow primarily by condensation of PAH on the particle surface. In contrast to previous DNS studies based on simplified soot and chemistry models, surface reactions are found to contribute barely to the growth of soot, for nucleation and condensation processes occurring in the fuel stream are responsible for the most of soot mass generation. Furthermore, the morphology of the soot aggregates is

  17. Effect of Dimethyl Ether Mixing on Soot Size Distribution in Premixed Ethylene Flame

    KAUST Repository

    Li, Zepeng

    2016-04-21

    inhibited the production of polycyclic aromatic hydrocarbons. At the same time, the addition of DME gave rise to the increase of the flame temperatures, which favored the production of OH radicals. The incremental concentration of OH radicals promoted the oxidation rate of soot particles. Additionally, soot samples from flames with higher DME mixing ratios showed higher O/C, H/C mass ratios and thus better oxidation characteristics. In summary, the addition of DME reduces soot emission in two ways: on the one hand, it inhibits soot nucleation and mass/size growth, then the production of soot particles decreases; on the other hand, it promotes soot oxidation process by increasing the concentration of OH radicals and improving the oxidation behavior of the soot particles, then more particles are oxidized. Both of them are responsible for the reduction of soot emissions at the presence of DME.

  18. Measuring and predicting sooting tendencies of oxygenates, alkanes, alkenes, cycloalkanes, and aromatics on a unified scale

    Energy Technology Data Exchange (ETDEWEB)

    Das, Dhrubajyoti D.; St. John, Peter C.; McEnally, Charles S.; Kim, Seonah; Pfefferle, Lisa D.

    2018-04-01

    Databases of sooting indices, based on measuring some aspect of sooting behavior in a standardized combustion environment, are useful in providing information on the comparative sooting tendencies of different fuels or pure compounds. However, newer biofuels have varied chemical structures including both aromatic and oxygenated functional groups, which expands the chemical space of relevant compounds. In this work, we propose a unified sooting tendency database for pure compounds, including both regular and oxygenated hydrocarbons, which is based on combining two disparate databases of yield-based sooting tendency measurements in the literature. Unification of the different databases was made possible by leveraging the greater dynamic range of the color ratio pyrometry soot diagnostic. This unified database contains a substantial number of pure compounds (greater than or equal to 400 total) from multiple categories of hydrocarbons important in modern fuels and establishes the sooting tendencies of aromatic and oxygenated hydrocarbons on the same numeric scale for the first time. Using this unified sooting tendency database, we have developed a predictive model for sooting behavior applicable to a broad range of hydrocarbons and oxygenated hydrocarbons. The model decomposes each compound into single-carbon fragments and assigns a sooting tendency contribution to each fragment based on regression against the unified database. The model's predictive accuracy (as demonstrated by leave-one-out cross-validation) is comparable to a previously developed, more detailed predictive model. The fitted model provides insight into the effects of chemical structure on soot formation, and cases where its predictions fail reveal the presence of more complicated kinetic sooting mechanisms. This work will therefore enable the rational design of low-sooting fuel blends from a wide range of feedstocks and chemical functionalities.

  19. Pathology residency training: time for a new paradigm.

    Science.gov (United States)

    Domen, Ronald E; Baccon, Jennifer

    2014-06-01

    The exponential growth of the field of pathology over the past several decades has created challenges for residency training programs. These challenges include the ability to train competent pathologists in 4 years, an increased demand for fellowship training, and the structuring and completion of maintenance of certification. The authors feel that pathology residency training has reached a critical point and that a new paradigm for training is required. Copyright © 2014 Elsevier Inc. All rights reserved.

  20. An investigation of late-combustion soot burnout in a DI diesel engine using simultaneous planar imaging of soot and OH radical

    Energy Technology Data Exchange (ETDEWEB)

    John E. Dec; Peter L. Kelly-Zion

    1999-10-01

    Diesel engine design continues to be driven by the need to improve performance while at the same time achieving further reductions in emissions. The development of new designs to accomplish these goals requires an understanding of how the emissions are produced in the engine. Laser-imaging diagnostics are uniquely capable of providing this information, and the understanding of diesel combustion and emissions formation has been advanced considerably in recent years by their application. However, previous studies have generally focused on the early and middle stages of diesel combustion. These previous laser-imaging studies do provide important insight into the soot formation and oxidation processes during the main combustion event. They indicate that prior to the end of injection, soot formation is initiated by fuel-rich premixed combustion (equivalence ratio > 4) near the upstream limit of the luminous portion of the reacting fuel jet. The soot is then oxidized at the diffusion flame around the periphery of the luminous plume. Under typical diesel engine conditions, the diffusion flame does not burn the remaining fuel and soot as rapidly as it is supplied, resulting in an expanding region of rich combustion products and soot. This is evident in natural emission images by the increasing size of the luminous soot cloud prior to the end of injection. Hence, the amount of soot in the combustion chamber typically increases until shortly after the end of fuel injection, at which time the main soot formation period ends and the burnout phase begins. Sampling valve and two-color pyrometry data indicate that the vast majority (more than 90%) of the soot formed is oxidized before combustion ends; however, it is generally thought that a small fraction of this soot from the main combustion zones is not consumed and is the source of tail pipe soot emissions.

  1. The role of topography on catchment‐scale water residence time

    Science.gov (United States)

    McGuire, K.J.; McDonnell, Jeffery J.; Weiler, M.; Kendall, C.; McGlynn, B.L.; Welker, J.M.; Seibert, J.

    2005-01-01

    The age, or residence time, of water is a fundamental descriptor of catchment hydrology, revealing information about the storage, flow pathways, and source of water in a single integrated measure. While there has been tremendous recent interest in residence time estimation to characterize watersheds, there are relatively few studies that have quantified residence time at the watershed scale, and fewer still that have extended those results beyond single catchments to larger landscape scales. We examined topographic controls on residence time for seven catchments (0.085–62.4 km2) that represent diverse geologic and geomorphic conditions in the western Cascade Mountains of Oregon. Our primary objective was to determine the dominant physical controls on catchment‐scale water residence time and specifically test the hypothesis that residence time is related to the size of the basin. Residence times were estimated by simple convolution models that described the transfer of precipitation isotopic composition to the stream network. We found that base flow mean residence times for exponential distributions ranged from 0.8 to 3.3 years. Mean residence time showed no correlation to basin area (r2 organization (i.e., topography) rather than basin area controls catchment‐scale transport. Results from this study may provide a framework for describing scale‐invariant transport across climatic and geologic conditions, whereby the internal form and structure of the basin defines the first‐order control on base flow residence time.

  2. Comparative Study of Different Methods for Soot Sensing and Filter Monitoring in Diesel Exhausts

    Directory of Open Access Journals (Sweden)

    Markus Feulner

    2017-02-01

    Full Text Available Due to increasingly tighter emission limits for diesel and gasoline engines, especially concerning particulate matter emissions, particulate filters are becoming indispensable devices for exhaust gas after treatment. Thereby, for an efficient engine and filter control strategy and a cost-efficient filter design, reliable technologies to determine the soot load of the filters and to measure particulate matter concentrations in the exhaust gas during vehicle operation are highly needed. In this study, different approaches for soot sensing are compared. Measurements were conducted on a dynamometer diesel engine test bench with a diesel particulate filter (DPF. The DPF was monitored by a relatively new microwave-based approach. Simultaneously, a resistive type soot sensor and a Pegasor soot sensing device as a reference system measured the soot concentration exhaust upstream of the DPF. By changing engine parameters, different engine out soot emission rates were set. It was found that the microwave-based signal may not only indicate directly the filter loading, but by a time derivative, the engine out soot emission rate can be deduced. Furthermore, by integrating the measured particulate mass in the exhaust, the soot load of the filter can be determined. In summary, all systems coincide well within certain boundaries and the filter itself can act as a soot sensor.

  3. Effect of secondary organic aerosol coating thickness on the real-time detection and characterization of biomass-burning soot by two particle mass spectrometers

    Science.gov (United States)

    Ahern, Adam T.; Subramanian, Ramachandran; Saliba, Georges; Lipsky, Eric M.; Donahue, Neil M.; Sullivan, Ryan C.

    2016-12-01

    Biomass burning is a large source of light-absorbing refractory black carbon (rBC) particles with a wide range of morphologies and sizes. The net radiative forcing from these particles is strongly dependent on the amount and composition of non-light-absorbing material internally mixed with the rBC and on the morphology of the mixed particles. Understanding how the mixing state and morphology of biomass-burning aerosol evolves in the atmosphere is critical for constraining the influence of these particles on radiative forcing and climate. We investigated the response of two commercial laser-based particle mass spectrometers, the vacuum ultraviolet (VUV) ablation LAAPTOF and the IR vaporization SP-AMS, to monodisperse biomass-burning particles as we sequentially coated the particles with secondary organic aerosol (SOA) from α-pinene ozonolysis. We studied three mobility-selected soot core sizes, each with a number of successively thicker coatings of SOA applied. Using IR laser vaporization, the SP-AMS had different changes in sensitivity to rBC compared to potassium as a function of applied SOA coatings. We show that this is due to different effective beam widths for the IR laser vaporization region of potassium versus black carbon. The SP-AMS's sensitivity to black carbon (BC) mass was not observed to plateau following successive SOA coatings, despite achieving high OA : BC mass ratios greater than 9. We also measured the ion fragmentation pattern of biomass-burning rBC and found it changed only slightly with increasing SOA mass. The average organic matter ion signal measured by the LAAPTOF demonstrated a positive correlation with the condensed SOA mass on individual particles, despite the inhomogeneity of the particle core compositions. This demonstrates that the LAAPTOF can obtain quantitative mass measurements of aged soot-particle composition from realistic biomass-burning particles with complex morphologies and composition.

  4. Effect of secondary organic aerosol coating thickness on the real-time detection and characterization of biomass-burning soot by two particle mass spectrometers

    Directory of Open Access Journals (Sweden)

    A. T. Ahern

    2016-12-01

    Full Text Available Biomass burning is a large source of light-absorbing refractory black carbon (rBC particles with a wide range of morphologies and sizes. The net radiative forcing from these particles is strongly dependent on the amount and composition of non-light-absorbing material internally mixed with the rBC and on the morphology of the mixed particles. Understanding how the mixing state and morphology of biomass-burning aerosol evolves in the atmosphere is critical for constraining the influence of these particles on radiative forcing and climate. We investigated the response of two commercial laser-based particle mass spectrometers, the vacuum ultraviolet (VUV ablation LAAPTOF and the IR vaporization SP-AMS, to monodisperse biomass-burning particles as we sequentially coated the particles with secondary organic aerosol (SOA from α-pinene ozonolysis. We studied three mobility-selected soot core sizes, each with a number of successively thicker coatings of SOA applied. Using IR laser vaporization, the SP-AMS had different changes in sensitivity to rBC compared to potassium as a function of applied SOA coatings. We show that this is due to different effective beam widths for the IR laser vaporization region of potassium versus black carbon. The SP-AMS's sensitivity to black carbon (BC mass was not observed to plateau following successive SOA coatings, despite achieving high OA : BC mass ratios greater than 9. We also measured the ion fragmentation pattern of biomass-burning rBC and found it changed only slightly with increasing SOA mass. The average organic matter ion signal measured by the LAAPTOF demonstrated a positive correlation with the condensed SOA mass on individual particles, despite the inhomogeneity of the particle core compositions. This demonstrates that the LAAPTOF can obtain quantitative mass measurements of aged soot-particle composition from realistic biomass-burning particles with complex morphologies and composition.

  5. Effects of zebra mussels on food webs: Interactions with juvenile bluegill and water residence time

    Science.gov (United States)

    Richardson, W.B.; Bartsch, L.A.

    1997-01-01

    We evaluated how water residence time mediated the impact of zebra mussels Dreissena polymorpha and bluegill sunfish Lepomis macrochirus on experimental food webs established in 1100-1 outdoor mesocosms. Water residence time was manipulated as a surrogate for seston resupply - a critical variable affecting growth and survival of suspension-feeding invertebrates. We used a 2 x 2 x 2 factorial experimental design with eight treatment combinations (3 replicates/treatment) including the presence or absence of Dreissena (2000 per m2), juvenile bluegill (40 per mesocosm), and short (1100 1 per d) or long (220 1 per d) water residence time. Measures of seston concentration (chlorophyll a, turbidity and suspended solids) were greater in the short- compared to long water-residence mesocosms, but intermediate in short water-residence mesocosms containing Dreissena. Abundance of rotifers (Keratella and Polyarthra) was reduced in Dreissena mesocosms and elevated in short residence time mesocosms. Cladocera abundance, in general, was unaffected by the presence of Dreissena; densities were higher in short-residence time mesocosms, and reduced in the presence of Lepomis. The growth of juvenile Lepomis were unaffected by Dreissena because of abundant benthic food. The final total mass of Dreissena was significantly greater in short- than long-residence mesocosms. Impacts of Dreissena on planktonic food webs may not only depend on the density of zebra mussels but also on the residence time of the surrounding water and the resupply of seston. ?? 1997 Kluwer Academic Publishers.

  6. Ceria-catlyzed soot oxidation studied by environmental transmission electron microscopy

    DEFF Research Database (Denmark)

    Simonsen, S.B.; Dahl, S.; Johnson, Erik

    2008-01-01

    Environmental tranmission electron microscopy (ETEM) was used to monitor in situ ceria-catalyzed oxidation of soot in relation to diesel engine emission control.  From time-lapsed ETEM image series of soot particles in contact with CeO2. or with Al2O3 as inert reference, mechanistic and kinetic...

  7. Defining and measuring the mean residence time of lateral surface transient storage zones in small streams

    Science.gov (United States)

    T.R. Jackson; R. Haggerty; S.V. Apte; A. Coleman; K.J. Drost

    2012-01-01

    Surface transient storage (STS) has functional significance in stream ecosystems because it increases solute interaction with sediments. After volume, mean residence time is the most important metric of STS, but it is unclear how this can be measured accurately or related to other timescales and field-measureable parameters. We studied mean residence time of lateral...

  8. Fast Soot Aging and Pronounced Diurnal Evolution of Size-dependent Soot Mixing State in the Megacity Beijing

    Science.gov (United States)

    Cheng, Y.; Su, H.; Wiedensohler, A.; Berghof, M.; Wehner, B.; Achtert, P.; Nowak, A.; Zhang, Y.; Shao, M.; Zhu, T.; Zeng, L.; Carmichael, G. R.

    2009-12-01

    The mixing state of soot has great implication in its optical and hygroscopic properties, and hence on its direct/indirect radiative effects. Up to date, understanding about the mechanism of the soot mixing state evolution is still poor and only a few techniques are able to measure the soot mixing state with a high-time and -size resolution. During the CAREBEIJING-2006 (Aug-Sep), a Volatility Tandem Differential Mobility Analyzer was applied to measure the soot mixture in a particle size range of 30 to 320 nm at a regional polluted site in the area of megacity Beijing [Wehner et al., 2009]. The number fraction of externally mixed soot (Fex) varied from 5 to 60% and showed a clear size-dependent diurnal variation. After a peak in the morning, Fex started decreasing and reached a minimum at around noon. Smaller particles reached the minimum earlier than the larger ones, i.e., Fex of 30 nm particles reached its minimum at 8:00-9:00 while that of 320 nm reached the minimum at 13:00-14:00. The different Fex variations among different sizes reflect a combined effect of size-dependent condensable vapor supersaturations and particle growth rates. Fast evolution of soot mixing states was found. During a typical day with new particle formation followed by continuously condensational growth [Wiedensohler et al., 2009], the coating enhancement in light absorption (σap) and scattering of coated soot can simultaneously reach up to a factor of 8-10 within several hours. It was contributed not only by the increasing thickness of coating shell but also by the fast transition from externally mixed soots to coated ones [Cheng et al., 2009]. The number fraction of coated soot (Fcoat) is strongly correlated with the photochemical aging process (e.g., OH time integrals (TOH) calculated by the ratio of m+p xylnene to ethylbenzen). Similar phenomena were found by Moteki et al. [2007] and Shiraiwa et al. [2007]. Interestingly, an “exponential decay” of the external mixed to coated

  9. A mechanistic study on the simultaneous elimination of soot and nitric oxide from engine exhaust

    KAUST Repository

    Raj, Abhijeet

    2011-04-01

    The non-catalytic interaction between soot and nitric oxide (NO) resulting in their simultaneous elimination was studied on different types of reactive site present on soot. The reaction mechanism proposed previously was extended by including seven new reaction pathways for which the reaction energetics and kinetics were studied using density functional theory and transition state theory. This has led to the calculation of a new rate for the removal of carbon monoxide (CO) from soot. The new pathways have been added to our polycyclic aromatic hydrocarbon (PAH) growth model and used to simulate the NO-soot interaction to form CO, N2 and N2O. The simulation results show satisfactory agreement with experiment for the new CO removal rate. The NO-soot reaction was found to depend strongly on the soot site type and temperature. For a set of temperatures, computed PAH structures were analysed to determine the functional groups responsible for the decrease in the reactivity of soot with NO with increasing reaction time. In isothermal conditions, it was found that as temperature is increased, the number of oxygen atoms remaining on the soot surface decreases, while the number of nitrogen atoms increases for a given reaction time. © 2010 Elsevier Ltd. All rights reserved.

  10. The impact of dredging on residence time in the Amba estuary, west coast of India

    Digital Repository Service at National Institute of Oceanography (India)

    Velamala, S.N.; Thomas, J.; Bari, S.; Kachave, S.

    increase from 1.2 to 1.3 tidal cycles after dredging. Keywords: Residence time. flushing time. modeling. lagrangian particle track. Amba estuary: India. 1. Introduction The rate of water exchange between an estuary and the open sea plays...; Monsen et al. 2002). For example, Delesalle and Sournia (1992) established a direct linear relationship between phytoplankton biomass in coral lagoons and the Residence time (RT). The rate of exchange is generally determined by 3 time scales, viz...

  11. Fluoroscopy time during uncomplicated unilateral ureteroscopy for urolithiasis decreases with urology resident experience.

    Science.gov (United States)

    Weld, Lancaster R; Nwoye, Uzoamaka O; Knight, Richard B; Baumgartner, Timothy S; Ebertowski, James S; Stringer, Matthew T; Kasprenski, Matthew C; Weld, Kyle J

    2015-01-01

    To determine predictors of fluoroscopy time during uncomplicated, unilateral ureteroscopy for urolithiasis performed by urology residents during the first 2 years of residency. The patient charts and computed tomography scans of consecutive, unilateral, uncomplicated ureteroscopy cases for urolithiasis were retrospectively reviewed. The cases were performed by beginning urology residents over the course of their first 2 years of urology residency training. A total of 200 ureteroscopy cases were reviewed. The mean stone diameter was 7.1 (±3.2) mm. Forty-three percent of cases were performed for renal stones and 58 % for ureteral stones. The mean operative time was 80.2 (±36.9) min. The mean fluoroscopy time was 69.1 (±38.2) s. No significant differences existed between cases performed by each of the two residents, and no statistical differences in case difficulty were observed throughout the study period. Linear regression analysis revealed the strongest association with lower fluoroscopy time to be increasing resident experience (p fluoroscopy time decreased by 79 % from 135 to 29 s per case. Other significant factors associated with increasing fluoroscopy time were placement of a postoperative stent under fluoroscopic guidance (p Fluoroscopy time during uncomplicated, unilateral ureteroscopy for urolithiasis decreases with increasing urology resident operative experience. Other technical options during ureteroscopy were also found to influence fluoroscopy time.

  12. Connections between residence time distributions and watershed characteristics across the continental US

    Science.gov (United States)

    Condon, L. E.; Maxwell, R. M.; Kollet, S. J.; Maher, K.; Haggerty, R.; Forrester, M. M.

    2016-12-01

    Although previous studies have demonstrated fractal residence time distributions in small watersheds, analyzing residence time scaling over large spatial areas is difficult with existing observational methods. For this study we use a fully integrated groundwater surface water simulation combined with Lagrangian particle tracking to evaluate connections between residence time distributions and watershed characteristics such as geology, topography and climate. Our simulation spans more than six million square kilometers of the continental US, encompassing a broad range of watershed sizes and physiographic settings. Simulated results demonstrate power law residence time distributions with peak age rages from 1.5 to 10.5 years. These ranges agree well with previous observational work and demonstrate the feasibility of using integrated models to simulate residence times. Comparing behavior between eight major watersheds, we show spatial variability in both the peak and the variance of the residence time distributions that can be related to model inputs. Peak age is well correlated with basin averaged hydraulic conductivity and the semi-variance corresponds to aridity. While power law age distributions have previously been attributed to fractal topography, these results illustrate the importance of subsurface characteristics and macro climate as additional controls on groundwater configuration and residence times.

  13. Investigation of optical properties of aging soot

    Science.gov (United States)

    Migliorini, F.; Thomson, K. A.; Smallwood, G. J.

    2011-08-01

    The optical properties of soot, in particular the propensity of soot to absorb and scatter light as a function of wavelength, are key parameters for the correct interpretation of soot optical diagnostics. An overview of the data available in the literature highlights the differences in the reported optical properties of aging soot. In many cases, the properties of mature soot are used when evaluating in-flame soot but this assumption might not be suitable for all conditions and should be checked. This need has been demonstrated by performed spectral resolved line-of-sight attenuation (Spec-LOSA) measurements on an ethylene/air premixed and non-premixed flame. Transmission electron microscopy of thermophoretically sampled soot was also performed to qualify the soot aging and to establish soot morphology in order to correct light extinction coefficients for the scattering contribution. The measured refractive index absorption function, E( m) λ , showed a very strong spectral dependence which also varied with height above the burner for both flames. However, above 700 nm, the slope of the refractive index function was near zero for both flames and all measurement heights. The upper visible and near infrared wavelengths are therefore recommended for soot optical measurements.

  14. Detection of Soot Using a Resistivity Sensor Device Employing Thermophoretic Particle Deposition

    Directory of Open Access Journals (Sweden)

    Doina Lutic

    2010-01-01

    Full Text Available Results are reported for thermophoretic deposition of soot particles on resistivity sensors as a monitoring technique for diesel exhaust particles with the potential of improved detection limit and sensitivity. Soot with similar characteristics as from diesel exhausts was generated by a propane flame and diluted in stages. The soot in a gas flow at 240–270C∘ was collected on an interdigitated electrode structure held at a considerably lower temperature, 105–125C∘. The time delay for reaching measurable resistance values, the subsequent rate, and magnitude of resistance decrease were a function of the distance between the fingers in the electrodes and the degree of dilution of the soot containing flow. Soot deposition and subsequent removal by heating the sensor support was also performed in a real diesel exhaust. Good similarities between the behavior in our laboratory system and the real diesel exhaust were noticed.

  15. Effect of oven residence time on mechanical properties in ...

    Indian Academy of Sciences (India)

    P L Ramkumar

    Source based formu- lation was proposed by Banerjee et al [16] for modelling layer by layer non-isothermal deposition of plastic. The proposed method was also used for calculating the cycle time for ... alternative to reduce the cycle time in comparison with ... the energy inputs to the processes and save significant energy as ...

  16. MODELING HOW A HURRICANE BARRIER IN NEW BEDFORD HARBOR, MASSACHUSETTS, AFFECTS THE HYDRODYNAMICS AND RESIDENCE TIMES

    Science.gov (United States)

    Two-dimensional hydrodynamic and transport models were used to simulate tidal and subtidal circulation, residence times, and the longitudinal distributions of conservative constituents in New Bedford Harbor, Massachusetts, before and after a hurricane barrier was constructed. The...

  17. Evaluation of Residence Time on Nitrogen Oxides Removal in Non-Thermal Plasma Reactor

    Science.gov (United States)

    Talebizadeh, Pouyan; Rahimzadeh, Hassan; Babaie, Meisam; Javadi Anaghizi, Saeed; Ghomi, Hamidreza; Ahmadi, Goodarz; Brown, Richard

    2015-01-01

    Non-thermal plasma (NTP) has been introduced over the last few years as a promising after- treatment system for nitrogen oxides and particulate matter removal from diesel exhaust. NTP technology has not been commercialised as yet, due to its high rate of energy consumption. Therefore, it is important to seek out new methods to improve NTP performance. Residence time is a crucial parameter in engine exhaust emissions treatment. In this paper, different electrode shapes are analysed and the corresponding residence time and NOx removal efficiency are studied. An axisymmetric laminar model is used for obtaining residence time distribution numerically using FLUENT software. If the mean residence time in a NTP plasma reactor increases, there will be a corresponding increase in the reaction time and consequently the pollutant removal efficiency increases. Three different screw thread electrodes and a rod electrode are examined. The results show the advantage of screw thread electrodes in comparison with the rod electrode. Furthermore, between the screw thread electrodes, the electrode with the thread width of 1 mm has the highest NOx removal due to higher residence time and a greater number of micro-discharges. The results show that the residence time of the screw thread electrode with a thread width of 1 mm is 21% more than for the rod electrode. PMID:26496630

  18. Evaluation of Residence Time on Nitrogen Oxides Removal in Non-Thermal Plasma Reactor.

    Directory of Open Access Journals (Sweden)

    Pouyan Talebizadeh

    Full Text Available Non-thermal plasma (NTP has been introduced over the last few years as a promising after- treatment system for nitrogen oxides and particulate matter removal from diesel exhaust. NTP technology has not been commercialised as yet, due to its high rate of energy consumption. Therefore, it is important to seek out new methods to improve NTP performance. Residence time is a crucial parameter in engine exhaust emissions treatment. In this paper, different electrode shapes are analysed and the corresponding residence time and NOx removal efficiency are studied. An axisymmetric laminar model is used for obtaining residence time distribution numerically using FLUENT software. If the mean residence time in a NTP plasma reactor increases, there will be a corresponding increase in the reaction time and consequently the pollutant removal efficiency increases. Three different screw thread electrodes and a rod electrode are examined. The results show the advantage of screw thread electrodes in comparison with the rod electrode. Furthermore, between the screw thread electrodes, the electrode with the thread width of 1 mm has the highest NOx removal due to higher residence time and a greater number of micro-discharges. The results show that the residence time of the screw thread electrode with a thread width of 1 mm is 21% more than for the rod electrode.

  19. Evaluation of Residence Time on Nitrogen Oxides Removal in Non-Thermal Plasma Reactor.

    Science.gov (United States)

    Talebizadeh, Pouyan; Rahimzadeh, Hassan; Babaie, Meisam; Javadi Anaghizi, Saeed; Ghomi, Hamidreza; Ahmadi, Goodarz; Brown, Richard

    2015-01-01

    Non-thermal plasma (NTP) has been introduced over the last few years as a promising after- treatment system for nitrogen oxides and particulate matter removal from diesel exhaust. NTP technology has not been commercialised as yet, due to its high rate of energy consumption. Therefore, it is important to seek out new methods to improve NTP performance. Residence time is a crucial parameter in engine exhaust emissions treatment. In this paper, different electrode shapes are analysed and the corresponding residence time and NOx removal efficiency are studied. An axisymmetric laminar model is used for obtaining residence time distribution numerically using FLUENT software. If the mean residence time in a NTP plasma reactor increases, there will be a corresponding increase in the reaction time and consequently the pollutant removal efficiency increases. Three different screw thread electrodes and a rod electrode are examined. The results show the advantage of screw thread electrodes in comparison with the rod electrode. Furthermore, between the screw thread electrodes, the electrode with the thread width of 1 mm has the highest NOx removal due to higher residence time and a greater number of micro-discharges. The results show that the residence time of the screw thread electrode with a thread width of 1 mm is 21% more than for the rod electrode.

  20. Investigations of the long-term effects of LII on soot and bath gas

    KAUST Repository

    Cenker, Emre

    2017-08-24

    A combination of high-repetition rate imaging, laser extinction measurements, two-colour soot pyrometry imaging, and high-resolution transmission electron microscopy of thermophoretically sampled soot is used to investigate the long-term and permanent effects of rapid heating of in-flame soot during laser-induced incandescence (LII). Experiments are carried out on a laminar non-premixed co-annular ethylene/air flame with various laser fluences. The high-repetition rate images clearly show that the heated and the neighbouring laser-border zones undergo a permanent transformation after the laser pulse, and advect vertically with the flow while the permanent marking is preserved. The soot volume fraction at the heated zone reduces due to the sublimation of soot and the subsequent enhanced oxidation. At the laser-border zones, however, optical thickness increases that may be due to thermophoretic forces drawing hot particles towards relatively cooler zones and the rapid compression of the bath gas induced by the pressure waves created by the expansion of the desorbed carbon clusters. Additionally sublimed carbon clusters can condense onto existing particles and contribute to increase of the optical thickness. Time-resolved two-colour pyrometry imaging show that the increased temperature of soot both in the heated and neighbouring laser-border zones persists for several milliseconds. This can be associated to the increase in the bath-gas temperature, and a change in the wavelength-dependent emissivity of soot particles induced by the thermal annealing of soot. Ex-situ analysis show that the lattice structure of the soot sampled at the laser-border zones tend to change and soot becomes more graphitic. This may be attributed to thermal annealing induced by elevated temperature.

  1. Light Absorption By Coated Soot

    Science.gov (United States)

    Sedlacek, A. J.; Lee, J.; Onasch, T. B.; Davidovits, P.; Cross, E. S.

    2009-12-01

    The contribution of aerosol absorption on direct radiative forcing is still an active area of research, in part, because aerosol extinction is dominated by light scattering and, in part, because the primary absorbing aerosol of interest, soot, exhibits complex aging behavior that alters its optical properties. The consequences of this can be evidenced by the work of Ramanathan and Carmichael (2008) who suggest that incorporating the atmospheric heating due to brown clouds will increase black carbon (BC) radiative forcing from the IPCC best estimate of 0.34 Wm-2 (±0.25 Wm-2) (IPCC 2007) to 0.9 Wm-2. This noteworthy degree of the uncertainty is due largely to the interdependence of BC optical properties on particle mixing state and aggregate morphology, each of which changes as the particle ages in the atmosphere and becomes encapsulated within a coating of inorganic and/or organic substances. With the advent of techniques that can directly measure aerosol light absorption without influences due to collection substrate or light scattering (e.g., photoacoustic spectroscopy (Arnott et al., 2005; Lack et al., 2006) and photothermal interferometry (Sedlacek and Lee 2007)) the potential exists for quantifying this interdependence. In July 2008, a laboratory-based measurement campaign, led by Boston College and Aerodyne, was initiated to begin addressing this interdependence. To achieve this objective measurements of both the optical and physical properties of flame-generated soot under nascent, coated and denuded conditions were conducted. In this paper, light absorption by dioctyl sebacate (DOS) encapsulated soot and sulfuric acid coated soot using the technique of photothermal interferometry will be presented. In the case of DOS-coated soot, a monotonic increase in light absorption as a function DOS coating thickness to nearly 100% is observed. This observation is consistent with a coating-induced amplification in particle light absorption. (Bond et al. 2006) However

  2. Modelling maximum adsorption capacities of soot and soot-like materials for PAHs and PCBs

    NARCIS (Netherlands)

    Noort, van P.C.M.; Jonker, M.T.O.; Koelmans, A.A.

    2004-01-01

    Recent studies have shown that not partitioning but adsorption is the main mechanism for sorption of hydrophobic organic compounds to soot and soot-like materials. For compounds that adsorb by van der Waals forces only, variation in soot-water distribution coefficients will result from differences

  3. Dielectric properties of PMMA/Soot nanocomposites.

    Science.gov (United States)

    Clayton, Lanetra M; Cinke, Martin; Meyyappan, M; Harmon, Julie P

    2007-07-01

    Dielectric analysis (DEA) of relaxation behavior in poly(methyl methacrylate) (PMMA) soot nanocomposites is described herein. The soot, an inexpensive material, consists of carbon nanotubes, amorphous and graphitic carbon and metal particles. Results are compared to earlier studies on PMMA/multi-walled nanotube (MWNT) composites and PMMA/single-walled nanotube (SWNT) composites. The beta relaxation process appeared to be unaffected by the presence of the soot, as was noted earlier in nanotube composites. The gamma relaxation region in PMMA, normally dielectrically inactive, was "awakened" in the PMMA/soot composite. This occurrence is consistent with previously published data on nanotube composites. The dielectric permittivity, s', increased with soot content. The sample with 1% soot exhibited a permittivity (at 100 Hz and 25 degrees C) of 7.3 as compared to 5.1 for neat PMMA. Soot increased the dielectric strength, deltaE, of the composites. The 1% soot sample exhibited a dielectric strength of 6.38, while the neat PMMA had a value of 2.95 at 40 degrees C. The symmetric broadening term (alpha) was slightly higher for the 1% composite at temperatures near the secondary relaxation and near the primary relaxation, but all samples deviated from symmetrical semi-circular behavior (alpha = 1). The impact of the soot filler is seen more clearly in dielectric properties than in mechanical properties studies conducted earlier.

  4. Allocation of Internal Medicine Resident Time in a Swiss Hospital: A Time and Motion Study of Day and Evening Shifts.

    Science.gov (United States)

    Wenger, Nathalie; Méan, Marie; Castioni, Julien; Marques-Vidal, Pedro; Waeber, Gérard; Garnier, Antoine

    2017-04-18

    Little current evidence documents how internal medicine residents spend their time at work, particularly with regard to the proportions of time spent in direct patient care versus using computers. To describe how residents allocate their time during day and evening hospital shifts. Time and motion study. Internal medicine residency at a university hospital in Switzerland, May to July 2015. 36 internal medicine residents with an average of 29 months of postgraduate training. Trained observers recorded the residents' activities using a tablet-based application. Twenty-two activities were categorized as directly related to patients, indirectly related to patients, communication, academic, nonmedical tasks, and transition. In addition, the presence of a patient or colleague and use of a computer or telephone during each activity was recorded. Residents were observed for a total of 696.7 hours. Day shifts lasted 11.6 hours (1.6 hours more than scheduled). During these shifts, activities indirectly related to patients accounted for 52.4% of the time, and activities directly related to patients accounted for 28.0%. Residents spent an average of 1.7 hours with patients, 5.2 hours using computers, and 13 minutes doing both. Time spent using a computer was scattered throughout the day, with the heaviest use after 6:00 p.m. The study involved a small sample from 1 institution. At this Swiss teaching hospital, internal medicine residents spent more time at work than scheduled. Activities indirectly related to patients predominated, and about half the workday was spent using a computer. Information Technology Department and Department of Internal Medicine of Lausanne University Hospital.

  5. The imprint of climate and geology on the residence times of groundwater

    Science.gov (United States)

    Maxwell, Reed M.; Condon, Laura E.; Kollet, Stefan J.; Maher, Kate; Haggerty, Roy; Forrester, Mary Michael

    2016-01-01

    Surface and subsurface flow dynamics govern residence time or water age until discharge, which is a key metric of storage and water availability for human use and ecosystem function. Although observations in small catchments have shown a fractal distribution of ages, residence times are difficult to directly quantify or measure in large basins. Here we use a simulation of major watersheds across North America to compute distributions of residence times. This simulation results in peak ages from 1.5 to 10.5 years, in agreement with isotopic observations from bomb-derived radioisotopes, and a wide range of residence times—from 0.1 to 10,000 years. This simulation suggests that peak residence times are controlled by the mean hydraulic conductivity, a function of the prevailing geology. The shape of the residence time distribution is dependent on aridity, which in turn determines water table depth and the frequency of shorter flow paths. These model results underscore the need for additional studies to characterize water ages in larger systems.

  6. Soot measurements for diesel and biodiesel spray combustion under high temperature highly diluted ambient conditions

    KAUST Repository

    Zhang, Ji

    2014-11-01

    This paper presents the soot temperature and KL factor for biodiesel, namely fatty acid methyl ester (FAME) and diesel fuel combustion in a constant volume chamber using a two-color technique. The KL factor is a parameter for soot concentration, where K is an absorption coefficient and proportional to the number density of soot particles, L is the geometric thickness of the flame along the optical detection axis, and KL factor is proportional to soot volume fraction. The main objective is to explore a combustion regime called high-temperature and highly-diluted combustion (HTHDC) and compare it with the conventional and low-temperature combustion (LTC) modes. The three different combustion regimes are implemented under different ambient temperatures (800 K, 1000 K, and 1400 K) and ambient oxygen concentrations (10%, 15%, and 21%). Results are presented in terms of soot temperature and KL factor images, time-resolved pixel-averaged soot temperature, KL factor, and spatially integrated KL factor over the soot area. The time-averaged results for these three regimes are compared for both diesel and biodiesel fuels. Results show complex combined effects of the ambient temperature and oxygen concentration, and that two-color temperature for the HTHDC mode at the 10% oxygen level can actually be lower than the conventional mode. Increasing ambient oxygen and temperature increases soot temperature. Diesel fuel results in higher soot temperature than biodiesel for all three regimes. Results also show that diesel and biodiesel fuels have very different burning and sooting behavior under the three different combustion regimes. For diesel fuel, the HTHDC regime offers better results in terms of lower soot than the conventional and LTC regimes, and the 10% O2, 1400 K ambient condition shows the lowest soot concentration while maintaining a moderate two-color temperature. For biodiesel, the 15% O2, 800 K ambient condition shows some advantages in terms of reducing soot

  7. Prevalence and cost of full-time research fellowships during general surgery residency: a national survey.

    Science.gov (United States)

    Robertson, Charles M; Klingensmith, Mary E; Coopersmith, Craig M

    2009-01-01

    To quantify the prevalence, outcomes, and cost of surgical resident research. General surgery is unique among graduate medical education programs because a large percentage of residents interrupt their clinical training to spend 1 to 3 years performing full-time research. No comprehensive data exists on the scope of this practice. Survey sent to all 239 program directors of general surgery residencies participating in the National Resident Matching Program. Response rate was 200 of 239 (84%). A total of 381 of 1052 trainees (36%) interrupt residency to pursue full-time research. The mean research fellowship length is 1.7 years, with 72% of trainees performing basic science research. A significant association was found between fellowship length and postresidency activity, with a 14.7% increase in clinical fellowship training and a 15.2% decrease in private practice positions for each year of full-time research (P < 0.0001). Program directors at 31% of programs reported increased clinical duties for research fellows as a result of Accreditation Council for Graduate Medical Education work hour regulations for clinical residents, whereas a further 10% of programs are currently considering such changes. It costs $41.5 million to pay the 634 trainees who perform research fellowships each year, the majority of which is paid for by departmental funds (40%) and institutional training grants (24%). Interrupting residency to perform a research fellowship is a common and costly practice among general surgery residents. Although performing a research fellowship is associated with clinical fellowship training after residency, it is unclear to what extent this practice leads to the development of surgical investigators after postgraduate training.

  8. Effect of Residence Time of Graphitisation on Thermal Conductivity of Molded Graphite

    Directory of Open Access Journals (Sweden)

    Pedy Artsanti

    2010-06-01

    Full Text Available The effect of residence time of graphitisation on thermal conductivity of molded graphite has been examined. The examination has been conducted by varying residence time of graphitisation of molded carbon with petroleum coke as raw material and coal tar pitch. Graphitisation has been conducted by heating molded graphite at 2500 °C in argon atmosphere with residention time of 10, 30 and 90 minutes. Graphitisation degree, density, shrinking mass and porosity of molded graphite were examined and so was its thermal conductivity. The result showed that the decrease of porosity and the increase of graphitisation degree due to the increasing of residention time of graphitisation will increase the thermal conductivity of graphite. Molded graphite graphitisized with residence time for 90 minutes residention time gave thermal conductivity of 2.134 Watt/mK and graphitization degree 0.718.

  9. Simulation of soot size distribution in an ethylene counterflow flame

    KAUST Repository

    Zhou, Kun

    2014-01-06

    Soot, an aggregate of carbonaceous particles produced during the rich combustion of fossil fuels, is an undesirable pollutant and health hazard. Soot evolution involves various dynamic processes: nucleation soot formation from polycyclic aromatic hydrocarbons (PAHs) condensation PAHs condensing on soot particle surface surface processes hydrogen-abstraction-C2H2-addition, oxidation coagulation two soot particles coagulating to form a bigger particle This simulation work investigates soot size distribution and morphology in an ethylene counterflow flame, using i). Chemkin with a method of moments to deal with the coupling between vapor consumption and soot formation; ii). Monte Carlo simulation of soot dynamics.

  10. Evaluation and optimisation of phenomenological multi-step soot model for spray combustion under diesel engine-like operating conditions

    Science.gov (United States)

    Pang, Kar Mun; Jangi, Mehdi; Bai, Xue-Song; Schramm, Jesper

    2015-05-01

    In this work, a two-dimensional computational fluid dynamics study is reported of an n-heptane combustion event and the associated soot formation process in a constant volume combustion chamber. The key interest here is to evaluate the sensitivity of the chemical kinetics and submodels of a semi-empirical soot model in predicting the associated events. Numerical computation is performed using an open-source code and a chemistry coordinate mapping approach is used to expedite the calculation. A library consisting of various phenomenological multi-step soot models is constructed and integrated with the spray combustion solver. Prior to the soot modelling, combustion simulations are carried out. Numerical results show that the ignition delay times and lift-off lengths exhibit good agreement with the experimental measurements across a wide range of operating conditions, apart from those in the cases with ambient temperature lower than 850 K. The variation of the soot precursor production with respect to the change of ambient oxygen levels qualitatively agrees with that of the conceptual models when the skeletal n-heptane mechanism is integrated with a reduced pyrene chemistry. Subsequently, a comprehensive sensitivity analysis is carried out to appraise the existing soot formation and oxidation submodels. It is revealed that the soot formation is captured when the surface growth rate is calculated using a square root function of the soot specific surface area and when a pressure-dependent model constant is considered. An optimised soot model is then proposed based on the knowledge gained through this exercise. With the implementation of optimised model, the simulated soot onset and transport phenomena before reaching quasi-steady state agree reasonably well with the experimental observation. Also, variation of spatial soot distribution and soot mass produced at oxygen molar fractions ranging from 10.0 to 21.0% for both low and high density conditions are reproduced.

  11. Residence time of pollutants discharged in the Gulf of Kachchh, northwestern Arabian Sea

    Digital Repository Service at National Institute of Oceanography (India)

    Patgaonkar, R.S.; Vethamony, P.; Lokesh, K.S.; Babu, M.T.

    − = 0 The residence time is defined as the time when the mass declines to 1/e of its initial value m 0 , i.e. τ== k t 1 This theory assumes steady state flow. It also assumes complete and instantaneous mixing and that mass leaving the system... of the time of release (spring vs neap tide), the location of release and the initial vertical placement (Warner et al, 2010). Generally during neap tides, residence time is maximum near the bottom of the estuary at the mid-salt intrusion length. During...

  12. In-situ measurements of the mixing state and optical properties of soot with implications for radiative forcing estimates.

    Science.gov (United States)

    Moffet, Ryan C; Prather, Kimberly A

    2009-07-21

    Our ability to predict how global temperatures will change in the future is currently limited by the large uncertainties associated with aerosols. Soot aerosols represent a major research focus as they influence climate by absorbing incoming solar radiation resulting in a highly uncertain warming effect. The uncertainty stems from the fact that the actual amount soot warms our atmosphere strongly depends on the manner and degree in which it is mixed with other species, a property referred to as mixing state. In global models and inferences from atmospheric heating measurements, soot radiative forcing estimates currently differ by a factor of 6, ranging between 0.2-1.2 W/m(2), making soot second only to CO(2) in terms of global warming potential. This article reports coupled in situ measurements of the size-resolved mixing state, optical properties, and aging timescales for soot particles. Fresh fractal soot particles dominate the measured absorption during peak traffic periods (6-9 AM local time). Immediately after sunrise, soot particles begin to age by developing a coating of secondary species including sulfate, ammonium, organics, nitrate, and water. Based on these direct measurements, the core-shell arrangement results in a maximum absorption enhancement of 1.6x over fresh soot. These atmospheric observations help explain the larger values for soot forcing measured by others and will be used to obtain closure in optical property measurements to reduce one of the largest remaining uncertainties in climate change.

  13. NASA: Black soot fuels global warming

    CERN Multimedia

    2003-01-01

    New research from NASA's Goddard Space Center scientists suggests emissions of black soot have been altering the way sunlight reflects off Earth's snow. The research indicates the soot could be responsible for as much as 25 percent of global warming over the past century (assorted news items, 1 paragraph each).

  14. Numerical simulation of combustion and soot under partially premixed combustion of low-octane gasoline

    KAUST Repository

    An, Yanzhao

    2017-09-23

    In-cylinder combustion visualization and engine-out soot particle emissions were investigated in an optical diesel engine fueled with low octane gasoline. Single injection strategy with an early injection timing (−30 CAD aTDC) was employed to achieve partially premixed combustion (PPC) condition. A high-speed color camera was used to record the combustion images for 150 cycles. The regulated emission of carbon dioxide, carbon monoxide, nitrogen oxides and soot mass concentration were measured experimentally. Full cycle engine simulations were performed using CONVERGE™ and the simulation results matched with the experimental results. The in-cylinder soot particle evolution was performed by coupling a reduced toluene reference fuel mechanism including the PAHs formation/oxidation reactions with particulate size mimic model. The results showed that PPC presents typical stratified combustion characteristics, which is significantly different from the conventional diesel spray-driven combustion. The in-cylinder temperature and equivalence ratio overlaid with soot-NO formation regime revealed that PPC operating condition under study mostly avoided the main sooting conditions throughout the entire combustion. The evaluation of temperature distribution showed formaldehyde could be regarded as an indicator for low temperature reactions, while hydroxyl group represents the high temperature reactions. Soot evolution happened during the combustion process, hydroxyl radicals promoted the soot oxidation.

  15. The Ice Nucleation Activity of Surface Modified Soot

    Science.gov (United States)

    Häusler, Thomas; Witek, Lorenz; Felgitsch, Laura; Hitzenberger, Regina; Grothe, Hinrich

    2017-04-01

    The ice nucleation efficiency of many important atmospheric particles remains poorly understood. Since soot is ubiquitous in the Earth's troposphere, they might have the potential to significantly impact the Earth's climate (Finlayson-Pitts and Pitts, 2000; Seinfeld and Pandis, 1998). Here we present the ice nucleation activity (INA) in immersion freezing mode of different types of soot. Therefor a CAST (combustion aerosol standard) generator was used to produce different kinds of soot samples. The CAST generator combusts a propane-air-mixture and deposits thereby produced soot on a polyvinyl fluoride filter. By varying the propane to air ratio, the amount of organic portion of the soot can be varied from black carbon (BC) with no organic content to brown carbon (BrC) with high organic content. To investigate the impact of functional sites of ice nuclei (IN), the soot samples were exposed to NO2 gas for a certain amount of time (30 to 360 minutes) to chemically modify the surface. Immersion freezing experiments were carried out in a unique reaction gadget. In this device a water-in-oil suspension (with the soot suspended in the aqueous phase) was cooled till the freezing point and was observed through a microscope (Pummer et al., 2012; Zolles et al., 2015) It was found that neither modified nor unmodified BC shows INA. On the contrary, unmodified BrC shows an INA at -32˚ C, which can be increased up to -20˚ C. The INA of BrC depends on the duration of NO2- exposure. To clarify the characteristics of the surface modifications, surface sensitive analysis like infrared spectroscopy and X-ray photoelectron spectroscopy were carried out. Finlayson-Pitts, B. J. and Pitts, J. N. J.: Chemistry of the Upper and Lower Atmosphere, Elsevier, New York, 2000. Pummer, B. G., Bauer, H., Bernardi, J., Bleicher, S., and Grothe, H.: Suspendable macromolecules are responsible for ice nucleation activity of birch and conifer pollen, Atmos Chem Phys, 12, 2541-2550, 2012. Seinfeld, J

  16. Design strategies to address kinetics of drug binding and residence time.

    Science.gov (United States)

    Cusack, Kevin P; Wang, Ying; Hoemann, Michael Z; Marjanovic, Jasmina; Heym, Roland G; Vasudevan, Anil

    2015-01-01

    The kinetics of drug binding and drug residence time are recognized to be important in the clinical effectiveness of drug candidates. In most cases a long residence time of the drug-target complex results in an extended duration of pharmacodynamic activity, even when systemic concentrations of drug have been notably reduced through elimination routes. Hence, if selective for target, long residence times can increase the duration of drug efficacy in vivo and can significantly diminish the potential for off-target-mediated toxicities. Furthermore, a compound with a slower dissociation rate may allow a reduced dosing schedule relative to a compound with a rapid dissociation rate. Factors contributing to long residence time that could be useful to medicinal chemists in the prospective design of compounds with long residence times will be discussed in this perspective. Particular emphasis will be on case studies highlighting how kinetics can be measured, modulated based on supporting structure kinetic relationships and whether these effects are translatable into man. Copyright © 2015 Elsevier Ltd. All rights reserved.

  17. Small particles big effect? - Investigating ice nucleation abilities of soot particles

    Science.gov (United States)

    Mahrt, Fabian; David, Robert O.; Lohmann, Ulrike; Stopford, Chris; Wu, Zhijun; Kanji, Zamin A.

    2017-04-01

    emissions. Collected particles will be re-suspended and aerosolized using an atomizer (TSI, model 3076) and dried by a diffusion drier prior to ice nucleation experiments. A Particle Phase Discriminator (PPD) coupled to HINC will allow discrimination of size-resolved liquid and ice hydrometeors formed on the atmospheric soot particles injected into the CFDC. This will allow to more precisely quantify the microphysical properties of these particles in cloud processes for the conditions tested. To our knowledge this is the first time such a coupling is done for atmospheric soot particles. Results show different activation behavior of the soot over the temperature range investigated. While CAST-brown soot needs conditions above water saturation to show any freezing, some of the commercial soot samples show heterogeneous ice nucleation well below water saturation for the cirrus conditions. For the mixed-phase cloud conditions all soot types show droplet activation for high water supersaturation.

  18. Residence times and decay rates of downed woody debris biomass/carbon in eastern US forests

    Science.gov (United States)

    Matthew B. Russell; Christopher W. Woodall; Shawn Fraver; Anthony W. D' Amato; Grant M. Domke; Kenneth E. Skog

    2014-01-01

    A key component in describing forest carbon (C) dynamics is the change in downed dead wood biomass through time. Specifically, there is a dearth of information regarding the residence time of downed woody debris (DWD), which may be reflected in the diversity of wood (for example, species, size, and stage of decay) and site attributes (for example, climate) across the...

  19. Strategic Application of Residence-Time Control in Continuous-Flow Reactors

    Science.gov (United States)

    Mándity, István M; Ötvös, Sándor B; Fülöp, Ferenc

    2015-01-01

    As a sustainable alternative for conventional batch-based synthetic techniques, the concept of continuous-flow processing has emerged in the synthesis of fine chemicals. Systematic tuning of the residence time, a key parameter of continuous-reaction technology, can govern the outcome of a chemical reaction by determining the reaction rate and the conversion and by influencing the product selectivity. This review furnishes a brief insight into flow reactions in which high chemo- and/or stereoselectivity can be attained by strategic residence-time control and illustrates the importance of the residence time as a crucial parameter in sustainable method development. Such a fine reaction control cannot be performed in conventional batch reaction set-ups. PMID:26246983

  20. Computation of residence time in the simulation of pulsatile ventricular assist devices

    Science.gov (United States)

    Long, C. C.; Esmaily-Moghadam, M.; Marsden, A. L.; Bazilevs, Y.

    2014-10-01

    A continuum-based model of particle residence time for moving-domain fluid mechanics and fluid-structure interaction (FSI) computations is proposed, analyzed, and applied to the simulation of an adult pulsatile ventricular assist device (PVAD). Residence time is a quantity of clinical interest for blood pumps because it correlates with thrombotic risk. The proposed technique may be easily implemented in any flow or FSI solver. In the context of PVADs the results of the model may be used to assess how efficiently the pump moves the blood through its interior. Three scalar measures of particle residence time are also proposed. These scalar quantities may be used in the PVAD design with the goal of reducing thrombotic risk.

  1. On the joint residence time of N independent two-dimensional Brownian motions

    International Nuclear Information System (INIS)

    Benichou, O; Coppey, M; Klafter, J; Moreau, M; Oshanin, G

    2003-01-01

    We study the behaviour of several joint residence times of N independent Brownian particles in a disc of radius R in two dimensions. We consider: (i) the time T N (t) spent by all N particles simultaneously in the disc within the time interval [0, t], (ii) the time T (m) N (t) which at least m out of N particles spend together in the disc within the time interval [0, t], and (iii) the time T-tilde (m) N (t) which exactly m out of N particles spend together in the disc within the time interval [0, t]. We obtain very simple exact expressions for the expectations of these three residence times in the limit t → ∞

  2. Implication of discharge pattern of radionuclides in the landscape on surface hydrological pathways and residence times

    International Nuclear Information System (INIS)

    Anders Woerman; Lars Marklund; Xu Shulan; Bjoern Dverstorp

    2005-01-01

    The safety analysis of the final repository of spent nuclear fuel will include large-scale migration behaviour of radionuclides that accidentally leak from the repository in deep bedrock. Physically based models of radionuclides release-processes would typically take into account the flow and transport in the hydrosphere as well as spreading through ecosystems to individual humans. This study addresses the coupling between discharge pattern in the landscape and factors controlling the residence times or radionuclides in the biosphere on land. The overall residence time on land is crucial because it controls the maximum exposure of radioactivity to individual humans. Numerical analysis indicate that variation in topography and quaternary deposits affect the discharge pattern in the landscape for radionuclides that escapes the waste repository in deep bedrock. Those analyses are based on extensive geographical data covering surface topography, stream network characteristics and geological structure on the continental scale of Scandinavia. Results on the discharge pattern in three typical Swedish landscapes are used as a basis for comparative analyses of the residence time distribution in surface hydrological systems for radionuclides that escape the waste repository. The groundwater flow analyses show that pathways of deep groundwater predominantly lead to the stream network, but to some extent also to lakes, wetlands and root uptake. The proportion varies slightly with altitude in the watershed as well as between different watersheds. The residence times in the stream network was based on convoluting the residence times for single discharge points over the entire stream network according to the technique of and data on stream distance distribution. The retardation due to uptake in the hyporheic zone was accounted for using the methods of and estimated sorption properties for Cs-137. The residence time for radionuclides in the hydrological systems of the continent

  3. Educating pediatric residents about breastfeeding: evaluation of 3 time-efficient teaching strategies.

    Science.gov (United States)

    Tender, Jennifer A F; Cuzzi, Sandra; Kind, Terry; Simmens, Samuel J; Blatt, Benjamin; Greenberg, Larrie

    2014-11-01

    Previously reported breastfeeding curricula for residents have combined different teaching methods, have focused on knowledge and attitudes, and have been time-intensive. This study aimed to evaluate 3 time-efficient breastfeeding curricula for effectiveness in regard to pediatric residents' knowledge, confidence, and skills in managing a simulated breastfeeding scenario. First-year pediatric residents during their 4-week community hospital newborn nursery rotation were consecutively assigned to 1 of 3 groups. Group 1 shadowed an International Board Certified Lactation Consultant (IBCLC) for 1 hour; group 2 watched a 25-minute case-based breastfeeding DVD; and group 3 observed a 3-hour prenatal parent breastfeeding class (CLS). Residents were assessed by (1) a pretest and posttest evaluating their breastfeeding knowledge and confidence, and (2) a clinical skills scenario managing a breastfeeding standardized patient (SP). Thirty-nine pediatric residents participated in the study (11 in IBCLC, 16 DVD, 12 CLS) over a 1-year period. All groups significantly improved their knowledge scores and confidence in managing breastfeeding problems, with the IBCLC group showing more improvement in knowledge than the other groups (P = .02) and a higher rating of their teaching method (P = .01). All groups performed well on the SP clinical skills scenario, with no significant difference between groups. All 3 teaching methods were time-efficient and produced important gains in knowledge and confidence, with residents in the IBCLC group demonstrating greatest improvement in knowledge and a higher rating of their teaching method. Our study provides support for 3 methods of teaching residents breastfeeding management and demonstrates that IBCLCs are well-received as interprofessional educators. © The Author(s) 2014.

  4. Comparison of soot formation for diesel and jet-a in a constant volume combustion chamber using two-color pyrometry

    KAUST Repository

    Jing, Wei

    2014-04-01

    The measurement of the two-color line of sight soot and KL factor for NO.2 diesel and jet-A fuels was conducted in an optical constant volume combustion chamber by using a high speed camera under 1000 K ambient temperature and varied oxygen concentration conditions. The ambient conditions were set as follows: four oxygen cases including 10%, 15%, 18% and 21% at 1000 K ambient temperature. KL factor and soot temperature were determined based on the two-color pyrometry technique using two band-pass filters with wavelengths of 650 nm and 550 nm. The results show that low soot temperature is observed in the upstream inner flame along the centerline, which is surrounded by high soot temperature regions, and a high KL factor is found in the same region with a low soot temperature. The results under different times suggest that soot temperature is higher for high O2 conditions during the entire flame development; meanwhile, both integrated KL factor and soot area decrease with the increase of O2 concentration. The two fuels share a similar trend of soot temperature and KL factor, however, diesel flame has a higher soot temperature and a larger high soot temperature area compared to jet-A flame. On the other hand, diesel flame shows a lower soot level during the quasi-steady state with a higher total soot level at the end of the combustion under low O2 conditions. A lower O2 concentration range from 10% to 15% is expected to have the possibility to achieve a simultaneous reduction of soot and NOx in sooting flames under the 1000 K ambient temperature condition. Copyright © 2014 SAE International.

  5. Improved soot blowing, based on needs, through measurement of the natural frequency of the heat transferring tubes; Foerbaettrad behovsstyrd sotning genom maetning av oeverfoerande tubernas egenfrekvens

    Energy Technology Data Exchange (ETDEWEB)

    Blom, Elisabet; Ivarsson, Christofer

    2007-11-15

    The aim of the project is to develop a method for detecting soot on the transferring tubes by measuring the Eigen frequency of the tubes as a function of the soot deposit growth. The project is a pilot study independent of boiler type and it is applicable to all boilers where soot deposit on transferring tubes is a repeating issue. The report is supposed to answer two major questions. Is it possible to make use of Eigen frequencies in order to trace soot deposit on transferring tubes? What governing parameters are related to the Eigen frequency of transferring tubes? By today, soot blowing is executed after recommendations from the manufacturer in terms of number of soot blowing per time unit. The fuel type as well as boiler type has great influence on the soot deposit growth. The objective of the project is to investigate whether the mechanical properties of the transferring tube can be used to detect soot deposit. The project is divided into a theoretical and a practical part. The theoretical part covers the design of the probe and the change of its mechanical properties when soot deposit is present. Practical experiments were then carried out in a laboratory were the probes mechanical properties with and without soot deposit were investigated. It was shown that the Eigen frequency of the probe decreased with an increased mass due to soot deposit. A test was also made in a boiler at SAKAB but difficulties in attaching the probe to the inspection hatch. The results varied and the interpretation of the results become difficult. However, it was obvious that the mechanical properties of the probe changed with the amount of soot deposit. It was concluded that detection of soot deposit by studying the mechanical properties of the transferring tubes is possible. Yet, using a probe is no optimal solution, instead measurements should be done directly on the heat transferring tubes. In addition, a strategy for controlling the soot deposit has to be developed

  6. Conceptual framework for model-based analysis of residence time distribution in twin-screw granulation

    DEFF Research Database (Denmark)

    Kumar, Ashish; Vercruysse, Jurgen; Vanhoorne, Valerie

    2015-01-01

    within each module where different granulation rate processes dominate over others. Currently, experimental data is used to determine the residence time distributions. In this study, a conceptual model based on classical chemical engineering methods is proposed to better understand and simulate...... the residence time distribution in a TSG. The experimental data were compared with the proposed most suitable conceptual model to estimate the parameters of the model and to analyse and predict the effects of changes in number of kneading discs and their stagger angle, screw speed and powder feed rate...

  7. Emissions of soot particles from heat generators

    Science.gov (United States)

    Lyubov, V. K.; Popov, A. N.; Popova, E. I.

    2017-11-01

    «Soot carbon» or «Soot» - incomplete combustion or thermal decomposition particulate carbon product of hydrocarbons consisting of particles of various shapes and sizes. Soot particles are harmful substances Class 2 and like a dust dispersed by wind for thousands of kilometers. Soot have more powerful negative factor than carbon dioxide. Therefore, more strict requirements on ecological and economical performance for energy facilities at Arctic areas have to be developed to protect fragile Arctic ecosystems and global climate change from degradation and destruction. Quantity of soot particles in the flue gases of energy facilities is a criterion of effectiveness for organization of the burning process. Some of heat generators do not provide the required energy and environmental efficiency which results in irrational use of energy resources and acute pollution of environment. The paper summarizes the results of experimental study of solid particles emission from wide range of capacity boilers burning different organic fuels (natural gas, fuel oil, coal and biofuels). Special attention is paid to environmental and energy performance of the biofuels combustion. Emissions of soot particles PM2.5 are listed. Structure, composition and dimensions of entrained particles with the use of electronic scanning microscope Zeiss SIGMA VP were also studied. The results reveal an impact of several factors on soot particles emission.

  8. Inferring detailed space use from movement paths: A unifying, residence time-based framework.

    Science.gov (United States)

    Kapota, Dror; Dolev, Amit; Saltz, David

    2017-10-01

    The residence time is the amount of time spent within a predefined circle surrounding each point along the movement path of an animal, reflecting its response to resource availability/quality. Two main residence time-based methods exist in the literature: (1) The variance of residence times along the path plotted against the radius of the circle was suggested to indicate the scale at which the animal perceives its resources; and (2) segments of the path with homogeneous residence times were suggested to indicate distinct behavioral modes, at a certain scale. Here, we modify and integrate these two methods to one framework with two steps of analysis: (1) identifying several distinct, nested scales of area-restricted search (ARS), providing an indication of how animals view complex resource landscapes, and also the resolutions at which the analysis should proceed; and (2) identifying places which the animal revisits multiple times and performs ARS; for these, we extract two scale-dependent statistical measures-the mean visit duration and the number of revisits in each place. The association between these measures is suggested as a signature of how animals utilize different habitats or resource types. The framework is validated through computer simulations combining different movement strategies and resource maps. We suggest that the framework provides information that is especially relevant when interpreting movement data in light of optimal behavior models, and which would have remained uncovered by either coarser or finer analyses.

  9. Effect of strain rate on sooting limits in counterflow diffusion flames of gaseous hydrocarbon fuels: Sooting temperature index and sooting sensitivity index

    KAUST Repository

    Wang, Yu

    2014-05-01

    The effect of the strain rate on the sooting limits in counterflow diffusion flames was investigated in various gaseous hydrocarbon fuels by varying the nitrogen dilution in the fuel and oxidizer streams. The sooting limit was defined as the critical fuel and oxygen mole fraction at which soot started to appear in the elastic light scattering signal. The sooting region for normal alkane fuels at a specified strain rate, in terms of the fuel and oxygen mole fraction, expanded as the number of carbon atoms increased. The alkene fuels (ethylene, propene) tested had a higher propensity for sooting as compared with alkane fuels with the same carbon numbers (ethane, propane). Branched iso-butane had a higher propensity for sooting than did n-butane. An increase in the strain rate reduced the tendency for sooting in all the fuels tested. The sensitivity of the sooting limit to the strain rate was more pronounced for less sooting fuels. When plotted in terms of calculated flame temperature, the critical oxygen mole fraction exhibited an Arrhenius form under sooting limit conditions, which can be utilized to significantly reduce the effort required to determine sooting limits at different strain rates. We found that the limiting temperatures of soot formation flames are viable sooting metrics for quantitatively rating the sooting tendency of various fuels, based on comparisons with threshold soot index and normalized smoke point data. We also introduce a sooting temperature index and a sooting sensitivity index, two quantitative measures to describe sooting propensity and its dependence on strain rate. © 2013 The Combustion Institute.

  10. Age and residence time of terrestrial source water in the northwest Atlantic shelf seas

    Science.gov (United States)

    He, R.; Todd, A. C.

    2016-02-01

    Coastal river mouths and bays are the junctions where terrestrial-source water meets and mixes with water from the open ocean. Once the riverine water reaches the coastal ocean, its eventual fate is largely unknown and difficult to trace. Rivers that flow into the ocean may contain high levels of nutrients and organic matter, so understanding the fate of terrestrial source water is important for a variety of biogeochemical processes that occur in the shelf seas. The fate of this terrestrial source water may be described in terms of its mean age (the time since it reached the ocean) and its residence time (the time it remains on the continental shelf). Using a high-resolution ocean model, we apply the constituent-oriented age and residence time (CART) theory to a large region encompassing the northwest Atlantic shelf seas to calculate the mean age of terrestrial source water and its residence time. For this application, 196 river mouths are used as sources of terrestrial water from South America to Nova Scotia. We investigate the spatial and seasonal variability of the water's mean age and compute the residence time within four different shelf regions: the Carribean Sea, the Gulf of Mexico, the South Atlantic Bight, and the Mid-Atlantic Bight/Gulf of Maine. From the estimates of mean age and residence time, we describe the impact of the coastal circulation on the eventual fate of terrestrial waters, and provide conjecture on how varying transport time scales may affect the general biogeochemical processes in the coastal ocean.

  11. Monte carlo simulation for soot dynamics

    KAUST Repository

    Zhou, Kun

    2012-01-01

    A new Monte Carlo method termed Comb-like frame Monte Carlo is developed to simulate the soot dynamics. Detailed stochastic error analysis is provided. Comb-like frame Monte Carlo is coupled with the gas phase solver Chemkin II to simulate soot formation in a 1-D premixed burner stabilized flame. The simulated soot number density, volume fraction, and particle size distribution all agree well with the measurement available in literature. The origin of the bimodal distribution of particle size distribution is revealed with quantitative proof.

  12. Particle residence times in waters of the Yangtze and Amazon continental shelves

    International Nuclear Information System (INIS)

    McKee, B.A.; Nittrouer, C.A.; DeMaster, D.J.

    1986-01-01

    Water column and seabed samples were analyzed for naturally occurring Th-234 to determine particle residence times in Yangtze and Amazon continental-shelf waters. On the Yangtze shelf, the water column was vertically well-mixed and suspended-sediment concentrations decreased offshore (from 230 mg/l near the river mouth to 2 mg/l in mid-shelf waters). Particle residence times increased offshore and ranged from 3.2 hours (12 m water depth) to 7.3 days (60 m water depth). Particle residence times ranged from 3 to 30 times shorter than values predicted by settling of discrete (4-8 micron) particles, suggesting that particles were settling in aggregate form. On the Amazon shelf, a two-layer estuarine flow dominated shelf circulation. Suspended-sediment concentrations on the inner shelf (10-12 m water depth) were much greater in bottom waters (range: 100-880 mg/l) than in surface waters (range 5-60 mg/l) as a result of resuspension. Particle residence times ranged from 1.1 days in surface waters to 2.5 days in bottom waters. Particles probably underwent several cycles of resuspension before permanent removal from the water column

  13. A High-Throughput Method for Measuring Drug Residence Time Using the Transcreener ADP Assay.

    Science.gov (United States)

    Kumar, Meera; Lowery, Robert G

    2017-08-01

    Analysis of drug-target residence times during drug development can result in improved efficacy, increased therapeutic window, and reduced side effects. Residence time can be estimated as the reciprocal of the dissociation rate ( k off ) of an inhibitor from its target. The traditional methods for measuring k off require synthesis of labeled ligands or low-throughput label-free methods. To provide an alternative that is better suited to an automated high-throughput screening (HTS) environment, we adapted a classic "jump dilution" catalytic assay method for determination of k off values for kinase inhibitor drugs. We used the Transcreener ADP 2 Kinase assay as a universal, homogenous method to monitor the recovery of kinase activity as the drugs dissociated from preformed inhibitor-kinase complexes. We measured residence times for several drugs that bind the epidermal growth factor receptor (EGFR), ABL1, and Aurora kinases and found that the rank ordering of inhibitor k off values correlated with literature values determined using ligand binding assays. Moreover, very similar results were obtained using the Transcreener assay with fluorescence polarization (FP), fluorescence intensity (FI), and time-resolved Förster resonance energy transfer (TR-FRET) detection modes. This HTS-compatible, generic assay method should facilitate the use of residence time as a parameter for compound prioritization and optimization early in kinase drug discovery programs.

  14. Temporal Evolution of Soot Particles from C2H2/O2 Combustion in a Closed Chamber

    Directory of Open Access Journals (Sweden)

    Bertran Celso A.

    2002-01-01

    Full Text Available An experimental study of soot formation in C2H2/O2 flames at different C/O ratios in a closed chamber was carried out. The evolution temporal behavior and the volume fraction of soot particles were determined by laser extinction. It was found that total time for the soot formation phenomenon in flames from C2H2/O2 with C/O ratio > 0.75 or C2H2/O2/Ar with C/O ratio = 1.00 was around 3.0-4.0 ms after ignition. At almost the same time the excited radicals reached their maximum emission intensity and the gases under combustion reached their maximum pressure. The micrographs show compact and approximately spherical soot particles with diameters within 60-150 nm. However, soot aggregates are not compact and they present a netlike structure similar to that of an aerogel.

  15. Development of a novel heterogeneous flow reactor -- Soot formation and nanoparticle catalysis

    Science.gov (United States)

    Camacho, Joaquin

    The development of novel experimental approaches to investigate fundamental surface kinetics is presented. Specifically, fundamental soot formation and surface catalysis processes are examined in isolation from other competing processes. In terms of soot formation, two experimental techniques are presented: the Burner Stabilized Stagnation (BSS) flame configuration is extended to isolate the effect of the parent fuel structure on soot formation and the fundamental rate of surface oxidation for nascent soot is measured in a novel aerosol flow reactor. In terms of nanoparticles, the physical and chemical properties of freely suspended nanoparticles are investigated in a novel aerosol flow reactor for methane oxidation catalyzed by palladium. The role of parent fuel structure within soot formation is examined by following the time resolved formation nascent soot from the onset of nucleation to later growth stages for premixed BSS flames. Specifically, the evolution of the detailed particle size distribution function (PSDF) is compared for butanol, butane and C6 hydrocarbons in two separate studies where the C/O ratio and temperature are fixed. Under this constraint, the overall sooting process were comparable as evidenced by similar time resolved bimodal PSDF. However, the nucleation time and the persistence of nucleation with time is strongly dependent upon the structure of the parent fuel. For the C6 hydrocarbon fuels, the fastest onset of soot nucleation is observed in cyclohexane and benzene flames and this may be due to significant aromatic formation that is predicted in the pre-flame region. In addition, the evolution of the PSDF shows that nucleation ends sooner in cylclohexane and benzene flames and this may be due to relatively quick depletion of soot precursors such as acetylene and benzene. Interestingly,within the butanol fuels studied the effect of the branched chain in i-butanol and i-butane was more significant than the presence of fuel bound oxygen. A

  16. Modelling and simulation of soot generation and transport

    OpenAIRE

    Hu, Xiaoqin

    2016-01-01

    Soot released from fires not only causes danger to lives and property damage, but also effects fire spread by altering the radiation characteristics of fire effluents. In many situations, it is the soot concentration that controls the fire development. Therefore, soot modelling is of great importance in fire safety science. This necessitates the development of a global and general soot model within fire field models that can simulate the amount of soot generated and transported in large-scale...

  17. Electrically heated particulate matter filter soot control system

    Science.gov (United States)

    Gonze, Eugene V.; Paratore, Jr., Michael J.; Bhatia, Garima

    2016-03-15

    A regeneration system includes a particulate matter (PM) filter with an upstream end for receiving exhaust gas and a downstream end. A control module determines a current soot loading level of the PM filter and compares the current soot loading level to a predetermined soot loading level. The control module permits regeneration of the PM filter when the current soot loading level is less than the predetermined soot loading level.

  18. Extra-regional residence time as a correlate of plant invasiveness: European archaeophytes in North America.

    Science.gov (United States)

    La Sorte, Frank A; Pysek, Petr

    2009-09-01

    Human activities have degraded biogeographical barriers to dispersal resulting in the spread and naturalization of increasing numbers of nonnative invasive species. One correlate of invasiveness within a region is residence time or time since introduction. Plant species that were introduced into Europe prior to AD 1500 (European archaeophytes) that were subsequently introduced into North America provide a unique opportunity to examine the effect of extra-regional residence time (i.e., residence time that occurred in a nonnative region before a species was introduced into a new region). Here, we examine how nonnative species with extensive extra-regional residence times have affected beta diversity among states in the contiguous United States of America based on an analysis of occupancy and distance decay of similarity. State floras contained an average of 3106 +/- 922 species (mean +/- SD) with 2318 +/- 757 species classified as native, 180 +/- 43 species as European archaeophyte, and 608 -236 species as other exotic with no European archaeophyte association. For European archaeophytes, 42% were identified as noxious weeds in the United States with 8% identified as agricultural and 14% as natural-area weeds (20%, 2%, and 13% for other exotics, respectively). In strong contrast to natives and other exotics, European archaeophytes were more widespread and presented weaker distance-decay patterns. Thus, European archaeophytes were more likely to become noxious weeds, particularly within agricultural areas, and were associated with significant losses in beta diversity. We suggest that this outcome is a consequence of extra-regional residence time, which allowed for the selection of species or the evolution of traits that favored the colonization of arable habitats associated with early agricultural activities in Europe, habitats that are widespread, resource rich, and uniformly distributed in the United States. Our findings suggest that a long-term trajectory can be

  19. Variability in organic carbon reactivity across lake residence time and trophic gradients

    Science.gov (United States)

    Evans, Chris D.; Futter, Martyn N.; Moldan, Filip; Valinia, Salar; Frogbrook, Zoe; Kothawala, Dolly N.

    2017-11-01

    The transport of dissolved organic carbon from land to ocean is a large dynamic component of the global carbon cycle. Inland waters are hotspots for organic matter turnover, via both biological and photochemical processes, and mediate carbon transfer between land, oceans and atmosphere. However, predicting dissolved organic carbon reactivity remains problematic. Here we present in situ dissolved organic carbon budget data from 82 predominantly European and North American water bodies with varying nutrient concentrations and water residence times ranging from one week to 700 years. We find that trophic status strongly regulates whether water bodies act as net dissolved organic carbon sources or sinks, and that rates of both dissolved organic carbon production and consumption can be predicted from water residence time. Our results suggest a dominant role of rapid light-driven removal in water bodies with a short water residence time, whereas in water bodies with longer residence times, slower biotic production and consumption processes are dominant and counterbalance one another. Eutrophication caused lakes to transition from sinks to sources of dissolved organic carbon. We conclude that rates and locations of dissolved organic carbon processing and associated CO2 emissions in inland waters may be misrepresented in global carbon budgets if temporal and spatial reactivity gradients are not accounted for.

  20. Dynamics of nitrate production and removal as a function of residence time in the hyporheic zone

    Science.gov (United States)

    Jay P. Zarnetske; Roy Haggerty; Steven M. Wondzell; Michelle A. Baker

    2011-01-01

    Biogeochemical reactions associated with stream nitrogen cycling, such as nitrification and denitrification, can be strongly controlled by water and solute residence times in the hyporheic zone (HZ). We used a whole-stream steady state 15N-Iabeled nitrate and conservative tracer addition to investigate the spatial and temporal physiochemical...

  1. LABORATORY AND NUMERICAL INVESTIGATIONS OF RESIDENCE TIME DISTRIBUTION OF FLUIDS IN LAMINAR FLOW STIRRED ANNULAR PHOTOREACTOR

    Science.gov (United States)

    Laboratory and Numerical Investigations of Residence Time Distribution of Fluids in Laminar Flow Stirred Annular PhotoreactorE. Sahle-Demessie1, Siefu Bekele2, U. R. Pillai11U.S. EPA, National Risk Management Research LaboratorySustainable Technology Division,...

  2. Fertilizer residence time affects nitrogen uptake efficiency and growth of sweet corn

    NARCIS (Netherlands)

    Zotarelli, L.; Scholberg, J.M.S.; Dukes, M.D.; Munoz-Carpena, R.

    2008-01-01

    Understanding plant N uptake dynamics is critical for increasing fertilizer N uptake efficiency (FUE) and minimize the risk of N leaching. The objective of this research was to determine the effect of residence time of N fertilizer on N uptake and FUE of sweet corn. Plants were grown in 25 L columns

  3. Conceptual framework for model-based analysis of residence time distribution in twin-screw granulation.

    Science.gov (United States)

    Kumar, Ashish; Vercruysse, Jurgen; Vanhoorne, Valérie; Toiviainen, Maunu; Panouillot, Pierre-Emmanuel; Juuti, Mikko; Vervaet, Chris; Remon, Jean Paul; Gernaey, Krist V; De Beer, Thomas; Nopens, Ingmar

    2015-04-25

    Twin-screw granulation is a promising continuous alternative for traditional batchwise wet granulation processes. The twin-screw granulator (TSG) screws consist of transport and kneading element modules. Therefore, the granulation to a large extent is governed by the residence time distribution within each module where different granulation rate processes dominate over others. Currently, experimental data is used to determine the residence time distributions. In this study, a conceptual model based on classical chemical engineering methods is proposed to better understand and simulate the residence time distribution in a TSG. The experimental data were compared with the proposed most suitable conceptual model to estimate the parameters of the model and to analyse and predict the effects of changes in number of kneading discs and their stagger angle, screw speed and powder feed rate on residence time. The study established that the kneading block in the screw configuration acts as a plug-flow zone inside the granulator. Furthermore, it was found that a balance between the throughput force and conveying rate is required to obtain a good axial mixing inside the twin-screw granulator. Although the granulation behaviour is different for other excipients, the experimental data collection and modelling methods applied in this study are generic and can be adapted to other excipients. Copyright © 2015 Elsevier B.V. All rights reserved.

  4. Factors influencing the residence time of catchment waters : A virtual experiment approach

    NARCIS (Netherlands)

    Dunn, S.M.; McDonnell, J.J.; Vaché, K.B.

    Estimates of mean residence time (MRT) are increasingly used as simple summary descriptors of the hydrological processes involving storage and mixing of water within catchment systems. Current understanding of the physical controls on MRT remains limited, and various hypotheses have been proposed to

  5. Residence times of alluvium in an east Texas stream as indicated by sediment color

    Science.gov (United States)

    Jonathan D. Phillips; Daniel A. Marion

    2001-01-01

    The relationships between sediment production, storage, and transport in fluvial systems are complex and variable. Key issues in addressing these relationships are the residence times of sediment delivered to the channel, and the proportion derived from recent upland erosion as opposed to remobilized alluvium. The systematic changes in iron geochemistry often...

  6. Polynuclear aromatic hydrocarbon and particulate emissions from two-stage combustion of polystyrene: the effects of the secondary furnace (afterburner) temperature and soot filtration.

    Science.gov (United States)

    Wang, Jun; Richter, Henning; Howard, Jack B; Levendis, Yiannis A; Carlson, Joel

    2002-02-15

    converted into soot, while the total mass of PAH represented about 3% of the initial mass of combustible. The afterburner reduced the particulate (soot) emissions by only 20-30%, which indicates that once soot is formed its destruction is rather difficult because its oxidation kinetics are slow undertypical furnace conditions. Moreover, increasing the afterburnertemperature resulted in an increasing trend of soot emissions therefrom, which might indicate competition between soot oxidation and formation, with some additional formation occurring at the higher temperatures. Contrary to the limited effect of the afterburner, high-temperature filtration of the combustion effluent prior to the exit of the primary furnace allowed for effective soot oxidation inside of the ceramic filter. Filtration drastically reduced soot emissions, by more than 90%. Limited soot formation in the afterburner was again observed with increasing temperatures. The yields of both CO and CO2 were largely unaffected by the temperature of the afterburner but increased at the presence of the filter indicating oxidation therein. A previously developed kinetic model was used to identify major chemical reaction pathways involving PAH in the afterburner. The experimental data at the exit of the primary furnace was used as input to these model computations. A first evaluation of the predictive capability of the model was conducted for the case with ceramic filter and a temperature of 900 degrees C. The afterburner was approximated as a plug-flow reactor, and model predictions at a residence time of 0.8 s were compared to experimental data collected at its exit. In agreement with the experimental PAH concentration, only a minor impact of the afterburner treatment was observed for most species at 900 degrees C. OH was deduced to be the major reactant with a mole fraction about 4 orders of magnitudes higher than that of hydrogen radicals. Evidence for the need of further work on the quantitative assessment of

  7. Residence time controls on nitrogen transformations in a permeable nearshore aquifer

    Science.gov (United States)

    Robinson, C. E.

    2015-12-01

    Permeable nearshore aquifers are an important biogeochemical hotspot for nitrogen (N) cycling. Located at the land-sea interface this hotspot has been shown to regulate N fluxes to coastal waters via submarine groundwater discharge. N transformations in a nearshore aquifer may result in either a net production or net removal of NO3- with the transformations controlled by complex interacting physical transport and biogeochemical kinetic processes. Oceanic forcing including tides and waves cause large quantities of seawater and chemical constituents, including dissolved oxygen and organic matter, to recirculate through the nearshore aquifer. There is currently limited understanding of the impact of the oceanic forcing on the residence time of recirculating constituents and the subsequent implications on N transformations in the aquifer. A numerical model was applied to quantify the influence of varying tidal and wave conditions on residence times and evaluate how the interactions between the coupled transport and reaction kinetics control N transformations and fluxes. Simulations were performed using the variable-density groundwater flow model SEAWAT-2005 combined with the reactive multi-component transport model PHT3D v2.10. The model simulated the transport and transformation of both marine- and land-derived chemical consitituents and considered oxic DOM mineralization, nitrification and denitrification. Simulations demonstrate that the recirculation residence times, combined with oxygen removal rates, regulate whether a nearshore aquifer will act as a net source or sink of NO3. Dimensionless Damköhler numbers calculated as the ratio of the characteristic residence time to characterisitic oxygen reaction time were determined and provide valuable insight into the residence time controls on the ultimate flux of N to the sea.

  8. Timed Up And Go Risk Predictor Of Falls In Elderly People Residing In The Community?

    Directory of Open Access Journals (Sweden)

    Mayara Muniz Peixoto Rodrigues

    2017-04-01

    Full Text Available Objective: evaluate the risk of falls of elderly people residing in a community in northeastern Brazil using the “Timed up and go”. Method: descriptive study, with a quantitative approach, performed with elderly people residing in a community. The collected data related to the sociodemographic and economic characteristics of episodes of falls in the last two years, regular practice of physical exercise and complaint of pain at the time of the interview; and, at last, the application of the “Timed Up and Go” test. Result: Most of the elderly were classified as free and independent and independent. There is a direct relationship between advanced age and increased time to perform the test. Conclusion: the "Timed Up and Go" test was not effective in predicting risk of falls alone and should associate with other indicators. Descriptors: Elderly people; Accidents by fall; Walking; Postural balance.

  9. The impact of carbon dioxide and exhaust gas recirculation on the oxidative reactivity of soot from ethylene flames and diesel engines

    Science.gov (United States)

    Al-Qurashi, Khalid O.

    important factor governing the soot reactivity. In the third phase of this research, diesel soot was generated under 0 and 20% EGR using a four-cylinder, four-stroke, turbocharged common rail direct injection (DI) DDC diesel engine. The objective of this work was to examine the relevance of the single cylinder engine and flame studies to practical engine operation. The key engine parameters such as load, speed, and injection timing were kept constant to isolate the EGR effect on soot properties from any other engine effects. The thermokinetic analyses of the flame soot and engine soot showed a significant increase in soot oxidation rate as a result of the CO2 or EGR inclusion into the combustion process. The activation energy of soot oxidation was found to be independent of soot origin or formation history. The increase in soot oxidation rate is attributed solely to the increase in soot active sites, which are presented implicitly in the pre-exponential factor (A) of the oxidation rate equation. This latter statement was confirmed by measuring the initial active site area (ASA i) of all soot samples considered in this study. As expected, higher oxidation rates are associated with higher ASAi. The chemical properties of the soot were investigated to determine their effects upon soot reactivity. The results showed that the H/C and O/C ratios were not modified by CO2 or EGR addition. Therefore, these ratios are not reactivity parameters and their effects upon soot reactivity were ruled out. In distinct contrast, the physical properties of the soot were modified by the addition of CO2 or EGR. The interlayer spacing (d002) between the aromatic sheets increased, the crystallite width (La) decreased and the crystallite height (Lc) decreased as a consequence of CO 2 or EGR addition. The modified physical properties of the soot are responsible for the increased rate of soot oxidation. In order to examine the soot oxidation behavior in the DPF, the soot samples produced from the DDC

  10. The role of residence times in two-patch dengue transmission dynamics and optimal strategies.

    Science.gov (United States)

    Lee, Sunmi; Castillo-Chavez, Carlos

    2015-06-07

    The reemergence and geographical dispersal of vector-borne diseases challenge global health experts around the world and in particular, dengue poses increasing difficulties in the Americas, due in part to explosive urban and semi-urban growth, increases of within and between region mobility, the absence of a vaccine, and the limited resources available for public health services. In this work, a simple deterministic two-patch model is introduced to assess the impact of dengue transmission dynamics in heterogeneous environments. The two-patch system models the movement (e.g. urban versus rural areas residence times) of individuals between and within patches/environments using residence-time matrices with entries that budget within and between host patch relative residence times, under the assumption that only the human budgets their residence time across regions. Three scenarios are considered: (i) resident hosts in Patch i visit patch j, where i≠j but not the other way around, a scenario referred to as unidirectional motion; (ii) symmetric bi-directional motion; and (iii) asymmetric bi-directional motion. Optimal control theory is used to identify and evaluate patch-specific control measures aimed at reducing dengue prevalence in humans and vectors at a minimal cost. Optimal policies are computed under different residence-matrix configurations mentioned above as well as transmissibility scenarios characterized by the magnitude of the basic reproduction number. Optimal patch-specific polices can ameliorate the impact of epidemic outbreaks substantially when the basic reproduction number is moderate. The final patch-specific epidemic size variation increases as the residence time matrix moves away from the symmetric case (asymmetry). As expected, the patch where individuals spend most of their time or in the patch where transmissibility is higher tend to support larger patch-specific final epidemic sizes. Hence, focusing on intervention that target areas where

  11. Electrometric Aviation Soot Monitor, Phase II

    Data.gov (United States)

    National Aeronautics and Space Administration — We propose to develop a sensitive PM measurement instrument to determine soot particle mass distribution from aircraft engine exhausts as well as from other IC...

  12. Non-thermal soot denuder, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — We propose to develop a non-thermal soot denuder for measuring chemical components of the nucleation mode particulate matter emissions from gas turbine engines, in...

  13. Method for removing soot from exhaust gases

    Science.gov (United States)

    Suib, Steven L.; Dharmarathna, D. A. Saminda; Pahalagedara, Lakshitha R.

    2018-01-16

    A method for oxidizing soot from diesel exhaust gas from a diesel engine. The method involves providing a diesel particulate filter for receiving the diesel exhaust gas; coating a catalyst composition on the diesel particulate filter; and contacting the soot from the diesel exhaust gas with the catalyst coated diesel particulate filter at a temperature sufficient to oxidize the soot to carbon dioxide. The catalyst composition is a doped or undoped manganese oxide octahedral molecular sieve (OMS-2) material. A diesel exhaust gas treatment system that includes a diesel particulate filter for receiving diesel exhaust gas from a diesel engine and collecting soot; and a catalyst composition coated on the diesel particulate filter. The catalyst composition is a doped or undoped manganese oxide octahedral molecular sieve (OMS-2).

  14. Electrometric aviation soot monitor, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — We propose to develop a highly sensitive and portable device to monitor soot particle mass distribution from aircraft engine exhaust. The proposed method is based on...

  15. Atmospheric soot aerosol measurements in Moscow

    Energy Technology Data Exchange (ETDEWEB)

    Kopeikin, V.M.; Pekour, M.S. [Institute of Atmospheric Physics, Moscow (Russian Federation)

    1996-12-31

    The results of regular soot concentration measurement in Moscow`s air for the period February 1989 - December 1995 are presented. The data obtained show that the level of soot contamination increased with the rate of approximately 0.42 mkg/m{sup 3} per year. 24-hour measurements of soot concentration and atmospheric boundary layer (ABL) parameters were carried out during 3 campaigns: May-June 1990, February 1991 and October-November 1993. Direct comparisons of local soot concentration with ABL characteristics reveals certain relationships, but also shows that local contamination strongly depends on many other parameters, such as source productivity, chemical reactions, air mass pre-history and so on.

  16. The pH-dependent adsorption of tributyltin to charcoals and soot

    International Nuclear Information System (INIS)

    Fang Liping; Borggaard, Ole K.; Marcussen, Helle; Holm, Peter E.; Bruun Hansen, Hans Christian

    2010-01-01

    Widespread use of tributyltin (TBT) poses a serious environmental problem. Adsorption by black carbon (BC) may strongly affect its behavior. The adsorption of TBT to well characterized soot and two charcoals with specific surface area in the range of 62-111 m 2 g -1 have been investigated with main focus on pH effects. The charcoals but not soot possess acidic functional groups. TBT adsorption reaches maximum at pH 6-7 for charcoals, and at pH > 6 for soot. Soot has between 1.5 and 15 times higher adsorption density (0.09-1.77 μmol m -2 ) than charcoals, but charcoals show up to 17 times higher sorption affinities than soot. TBT adsorption is successfully described by a new pH-dependent dual Langmuir model considering electrostatic and hydrophobic adsorption, and pH effects on TBT speciation and BC surface charge. It is inferred that strong sorption of the TBTOH species to BC may affect TBT toxicity. - Tributyltin adsorption to black carbon increases at increasing pH but charcoal exhibits electrostatic and hydrophobic adsorption, whereas soot only adsorbs hydrophobically.

  17. Changes of ns-soot mixing states and shapes in an urban area during CalNex

    Science.gov (United States)

    Adachi, Kouji; Buseck, Peter R.

    2013-05-01

    Aerosol particles from megacities influence the regional and global climate as well as the health of their occupants. We used transmission electron microscopes (TEMs) to study aerosol particles collected from the Los Angeles area during the 2010 CalNex campaign. We detected major amounts of ns-soot, defined as consisting of carbon nanospheres, sulfate, sea salt, and organic aerosol (OA) and lesser amounts of brochosome particles from leaf hoppers. Ns-soot-particle shapes, mixing states, and abundances varied significantly with sampling times and days. Within plumes having high CO2 concentrations, much ns-soot was compacted and contained a relatively large number of carbon nanospheres. Ns-soot particles from both CalNex samples and Mexico City, the latter collected in 2006, had a wide range of shapes when mixed with other aerosol particles, but neither sets showed spherical ns-soot nor the core-shell configuration that is commonly used in optical calculations. Our TEM observations and light-absorption calculations of modeled particles indicate that, in contrast to ns-soot particles that are embedded within other materials or have the hypothesized core-shell configurations, those attached to other aerosol particles hardly enhance their light absorption. We conclude that the ways in which ns-soot mixes with other particles explain the observations of smaller light amplification by ns-soot coatings than model calculations during the CalNex campaign and presumably in other areas.

  18. How Entrustment Is Informed by Holistic Judgments Across Time in a Family Medicine Residency Program: An Ethnographic Nonparticipant Observational Study.

    Science.gov (United States)

    Sagasser, Margaretha H; Fluit, Cornelia R M G; van Weel, Chris; van der Vleuten, Cees P M; Kramer, Anneke W M

    2017-06-01

    Entrustment has mainly been conceptualized as delegating discrete professional tasks. Because residents provide most of their patient care independently, not all resident performance is visible to supervisors; the entrustment process involves more than granting discrete tasks. This study explored how supervisors made entrustment decisions based on residents' performance in a long-term family medicine training program. A qualitative nonparticipant observational study was conducted in 2014-2015 at competency-based family medicine residency programs in the Netherlands. Seven supervisor-resident pairs participated. During two days, one researcher observed first-year residents' patient encounters, debriefing sessions, and supervisor-resident educational meetings and interviewed them separately afterwards. Data were collected and analyzed using iterative, phenomenological inductive research methodology. The entrustment process developed over three phases. Supervisors based their initial entrustment on prior knowledge about the resident. In the ensuing two weeks, entrustment decisions regarding independent patient care were derived from residents' observed general competencies necessary for a range of health problems (clinical reasoning, decision making, relating to patients); medical knowledge and skills; and supervisors' intuition. Supervisors provided supervision during and after encounters. Once residents performed independently, supervisors kept reevaluating their decisions, informed by residents' overall growth in competencies rather than by adhering to a predefined set of tasks. Supervisors in family medicine residency training took a holistic approach to trust, based on general competencies, knowledge, skills, and intuition. Entrustment started before training and developed over time. Building trust is a mutual process between supervisor and resident, requiring a good working relationship.

  19. Sooting limit in counterflow diffusion flames of ethylene/propane fuels and implication to threshold soot index

    KAUST Repository

    Joo, Peter H.

    2013-01-01

    Sooting limits in counterflow diffusion flames of propane/ethylene fuels have been studied experimentally using a light scattering technique, including the effects of dilution, fuel mixing, and strain rate. The results are discussed in view of the threshold soot index (TSI). In soot-formation (SF) flames, where the flame is located on the oxidizer side of the stagnation plane, the sooting limit depends critically on fuel type and subsequently on flame temperature. The sooting limit has a non-linear dependence on the fuel-mixing ratio, which is similar to the non-linear mixing rule for TSI observed experimentally in rich premixed flames, where soot oxidation is absent for both SF and rich premixed flames. In soot-formation-oxidation (SFO) flames, where the flame is located on the fuel side, the sooting limit depends critically on flame temperature, while it is relatively independent on fuel type. This result suggests a linear mixing rule for sooting limits in SFO flames, which is similar to the TSI behavior for coflow diffusion flames. Soot oxidation takes place for both types of flames. The aerodynamic strain effect on the sooting limits has also been studied and an appreciable influence has been observed. Under sooting conditions, soot volume fraction was measured using a light extinction technique. The soot loadings in SF flames of the mixture fuels demonstrated a synergistic effect, i.e., soot production increased for certain mixture fuels as compared to the respective singlecomponent fuels. © 2012 The Combustion Institute.

  20. Aromatics Oxidation and Soot Formation in Flames

    Energy Technology Data Exchange (ETDEWEB)

    Howard, J. B.; Richter, H.

    2005-03-29

    This project is concerned with the kinetics and mechanisms of aromatics oxidation and the growth process to polycyclic aromatic hydrocarbons (PAH) of increasing size, soot and fullerenes formation in flames. The overall objective of the experimental aromatics oxidation work is to extend the set of available data by measuring concentration profiles for decomposition intermediates such as phenyl, cyclopentadienyl, phenoxy or indenyl radicals which could not be measured with molecular-beam mass spectrometry to permit further refinement and testing of benzene oxidation mechanisms. The focus includes PAH radicals which are thought to play a major role in the soot formation process while their concentrations are in many cases too low to permit measurement with conventional mass spectrometry. The radical species measurements are used in critical testing and improvement of a kinetic model describing benzene oxidation and PAH growth. Thermodynamic property data of selected species are determined computationally, for instance using density functional theory (DFT). Potential energy surfaces are explored in order to identify additional reaction pathways. The ultimate goal is to understand the conversion of high molecular weight compounds to nascent soot particles, to assess the roles of planar and curved PAH and relationships between soot and fullerenes formation. The specific aims are to characterize both the high molecular weight compounds involved in the nucleation of soot particles and the structure of soot including internal nanoscale features indicative of contributions of planar and/or curved PAH to particle inception.

  1. Sustained increase in resident meal time hand hygiene through an interdisciplinary intervention engaging long-term care facility residents and staff.

    Science.gov (United States)

    O'Donnell, Marguerite; Harris, Tony; Horn, Terancita; Midamba, Blondelle; Primes, Vickie; Sullivan, Nancy; Shuler, Rosalyn; Zabarsky, Trina F; Deshpande, Abhishek; Sunkesula, Venkata C K; Kundrapu, Sirisha; Donskey, Curtis J

    2015-02-01

    Hand hygiene by patients may prevent acquisition and dissemination of health care-associated pathogens, but limited efforts have been made to engage patients in hand hygiene interventions. In a long-term care facility, we found that residents were aware of the importance of hand hygiene, but barriers, such as inaccessible products or difficult to use products, limited compliance. A dramatic and sustained improvement in meal time hand hygiene was achieved through engagement of staff and residents. Published by Elsevier Inc.

  2. Asymptotic analysis soot model and experiment for a directed injection engine

    Science.gov (United States)

    Liu, Yongfeng; Pei, Pucheng; Xiong, Qinghui; Lu, Yong

    2012-09-01

    The existing soot models are either too complex and can not be applied to the internal combustion engine, or too simple to make calculation errors. Exploring the soot model becomes the pursuit of the goal of many researchers within the error range in the current computer speed. On the basis of the latest experimental results, TP (temperature phases) model is presented as a new soot model to carry out optimization calculation for a high-pressure common rail diesel engine. Temperature and excess air factor are the most important two parameters in this model. When zone temperature T0.6, only the soot precursors—polycyclic aromatic hydrocarbons(PAH) is created and there is no soot emission. When zone temperature T ⩾ 1 500 K and excess air factor Φinjection time, variation of rail pressure and variation of speed among TP models. The experimental results indicate that the TP model can carry out optimization and computational fluid dynamics can be a tool to calculate for a high-pressure common rail directed injection diesel engine. The TP model result is closer than the use of the original KIVA-3V results of soot model accuracy by about 50% and TP model gives a new method for engine researchers.

  3. Reducing the residence time of a bouncing drop with spoked macrotexture

    Science.gov (United States)

    Patterson, Colin; Bird, James

    2015-11-01

    Liquid drops can bounce when they impact non-wetting surfaces. Recently, studies have demonstrated that the time that the bouncing drop resides at the surface can be adjusted with the presence of ridged macrotextures. When non-parallel macrotextures are present, they intersect to create spoked junctions. At sufficient velocity, a drop impacting a junction might be expected to breakup into smaller droplets; yet it is unclear how many droplets would be produced and the time for these droplets to clear the surface. Here, we show that the number droplets and overall residence time depends on both the number of spokes and the Weber number. We experimentally demonstrate that the center-assisted recoil framework extends beyond superhydrophobic surfaces to those above the Leidenfrost temperature. Finally, we present a physical model that rationalizes our results.

  4. Using continuous underway isotope measurements to map water residence time in hydrodynamically complex tidal environments

    Science.gov (United States)

    Downing, Bryan D.; Bergamaschi, Brian; Kendall, Carol; Kraus, Tamara; Dennis, Kate J.; Carter, Jeffery A.; von Dessonneck, Travis

    2016-01-01

    Stable isotopes present in water (δ2H, δ18O) have been used extensively to evaluate hydrological processes on the basis of parameters such as evaporation, precipitation, mixing, and residence time. In estuarine aquatic habitats, residence time (τ) is a major driver of biogeochemical processes, affecting trophic subsidies and conditions in fish-spawning habitats. But τ is highly variable in estuaries, owing to constant changes in river inflows, tides, wind, and water height, all of which combine to affect τ in unpredictable ways. It recently became feasible to measure δ2H and δ18O continuously, at a high sampling frequency (1 Hz), using diffusion sample introduction into a cavity ring-down spectrometer. To better understand the relationship of τ to biogeochemical processes in a dynamic estuarine system, we continuously measured δ2H and δ18O, nitrate and water quality parameters, on board a small, high-speed boat (5 to >10 m s–1) fitted with a hull-mounted underwater intake. We then calculated τ as is classically done using the isotopic signals of evaporation. The result was high-resolution (∼10 m) maps of residence time, nitrate, and other parameters that showed strong spatial gradients corresponding to geomorphic attributes of the different channels in the area. The mean measured value of τ was 30.5 d, with a range of 0–50 d. We used the measured spatial gradients in both τ and nitrate to calculate whole-ecosystem uptake rates, and the values ranged from 0.006 to 0.039 d–1. The capability to measure residence time over single tidal cycles in estuaries will be useful for evaluating and further understanding drivers of phytoplankton abundance, resolving differences attributable to mixing and water sources, explicitly calculating biogeochemical rates, and exploring the complex linkages among time-dependent biogeochemical processes in hydrodynamically complex environments such as estuaries.

  5. Does residence time affect responses of alien species richness to environmental and spatial processes?

    Directory of Open Access Journals (Sweden)

    Matteo Dainese

    2012-08-01

    Full Text Available One of the most robust emerging generalisations in invasion biology is that the probability of invasion increases with the time since introduction (residence time. We analysed the spatial distribution of alien vascular plant species in a region of north-eastern Italy to understand the influence of residence time on patterns of alien species richness. Neophytes were grouped according to three periods of arrival in the study region (1500–1800, 1800–1900, and > 1900. We applied multiple regression (spatial and non-spatial with hierarchical partitioning to determine the influence of climate and human pressure on species richness within the groups. We also applied variation partitioning to evaluate the relative importance of environmental and spatial processes. Temperature mainly influenced groups with speciesa longer residence time, while human pressure influenced the more recently introduced species, although its influence remained significant in all groups. Partial regression analyses showed that most of the variation explained by the models is attributable to spatially structured environmental variation, while environment and space had small independent effects. However, effects independent of environment decreased, and spatially independent effects increased, from older to the more recent neophytes. Our data illustrate that the distribution of alien species richness for species that arrived recently is related to propagule pressure, availability of novel niches created by human activity, and neutral-based (dispersal limitation processes, while climate filtering plays a key role in the distribution of species that arrived earlier. This study highlights the importance of residence time, spatial structure, and environmental conditions in the patterns of alien species richness and for a better understanding of its geographical variation.

  6. Characterizing Drug-Target Residence Time with Metadynamics: How To Achieve Dissociation Rate Efficiently without Losing Accuracy against Time-Consuming Approaches.

    Science.gov (United States)

    Sun, Huiyong; Li, Youyong; Shen, Mingyun; Li, Dan; Kang, Yu; Hou, Tingjun

    2017-08-28

    Drug-target residence time plays a vital role in drug efficacy. However, there is still no effective strategy to predict drug residence time. Here, we propose to use the optimized (or minimized) structures derived from holo-state proteins to calculate drug residence time, which could give a comparable or even better prediction accuracy compared with those calculated utilizing a large number of molecular dynamics (MD) structures based on the Poisson process. Besides, in addition to the Poisson process, one may use fewer samples for predicting residence time due to the reason that, in a large extent, the calculated drug residence time is stable and independent of the number of samples used for the prediction. With remarkably reduced computational load, the proposed strategy may be promising for large-scale drug residence time prediction, such as post-processing in virtual screening (VS) and lead compound optimization.

  7. Residence time of contaminants released in surface coal mines: A wind-tunnel study

    Energy Technology Data Exchange (ETDEWEB)

    Thompson, R.S.

    1993-08-01

    The 1990 Clean Air Act Amendments direct the U.S. Environmental Protection Agency to evaluate and modify, as required, existing dispersion models for the prediction of dispersion of dust from surface coal mines. The application of mathematical air pollution dispersion models to the dispersion of dust from surface coal mines requires knowledge of not only the amount of dust generated in the mine, but the fraction of that generated that actually escapes from the mine. The escape fraction can be related to the residence time that released material will remain, on average, within the mine. The concentration in the mine was found to follow an exponential decay function from which an exponential decay time constant (or residence time) was computed for each case. A semi-empirical formula was found that related the residence time to the mine geometry and wind direction quite well. This formula can be used to estimate escape fraction in determining the source strength for the application of mathematical dispersion models.

  8. Chaotic itinerancy and power-law residence time distribution in stochastic dynamical systems.

    Science.gov (United States)

    Namikawa, Jun

    2005-08-01

    Chaotic itinerant motion among varieties of ordered states is described by a stochastic model based on the mechanism of chaotic itinerancy. The model consists of a random walk on a half-line and a Markov chain with a transition probability matrix. The stability of attractor ruin in the model is investigated by analyzing the residence time distribution of orbits at attractor ruins. It is shown that the residence time distribution averaged over all attractor ruins can be described by the superposition of (truncated) power-law distributions if the basin of attraction for each attractor ruin has a zero measure. This result is confirmed by simulation of models exhibiting chaotic itinerancy. Chaotic itinerancy is also shown to be absent in coupled Milnor attractor systems if the transition probability among attractor ruins can be represented as a Markov chain.

  9. Classification of Animal Movement Behavior through Residence in Space and Time.

    Science.gov (United States)

    Torres, Leigh G; Orben, Rachael A; Tolkova, Irina; Thompson, David R

    2017-01-01

    Identification and classification of behavior states in animal movement data can be complex, temporally biased, time-intensive, scale-dependent, and unstandardized across studies and taxa. Large movement datasets are increasingly common and there is a need for efficient methods of data exploration that adjust to the individual variability of each track. We present the Residence in Space and Time (RST) method to classify behavior patterns in movement data based on the concept that behavior states can be partitioned by the amount of space and time occupied in an area of constant scale. Using normalized values of Residence Time and Residence Distance within a constant search radius, RST is able to differentiate behavior patterns that are time-intensive (e.g., rest), time & distance-intensive (e.g., area restricted search), and transit (short time and distance). We use grey-headed albatross (Thalassarche chrysostoma) GPS tracks to demonstrate RST's ability to classify behavior patterns and adjust to the inherent scale and individuality of each track. Next, we evaluate RST's ability to discriminate between behavior states relative to other classical movement metrics. We then temporally sub-sample albatross track data to illustrate RST's response to less resolved data. Finally, we evaluate RST's performance using datasets from four taxa with diverse ecology, functional scales, ecosystems, and data-types. We conclude that RST is a robust, rapid, and flexible method for detailed exploratory analysis and meta-analyses of behavioral states in animal movement data based on its ability to integrate distance and time measurements into one descriptive metric of behavior groupings. Given the increasing amount of animal movement data collected, it is timely and useful to implement a consistent metric of behavior classification to enable efficient and comparative analyses. Overall, the application of RST to objectively explore and compare behavior patterns in movement data can

  10. Classification of Animal Movement Behavior through Residence in Space and Time.

    Directory of Open Access Journals (Sweden)

    Leigh G Torres

    Full Text Available Identification and classification of behavior states in animal movement data can be complex, temporally biased, time-intensive, scale-dependent, and unstandardized across studies and taxa. Large movement datasets are increasingly common and there is a need for efficient methods of data exploration that adjust to the individual variability of each track. We present the Residence in Space and Time (RST method to classify behavior patterns in movement data based on the concept that behavior states can be partitioned by the amount of space and time occupied in an area of constant scale. Using normalized values of Residence Time and Residence Distance within a constant search radius, RST is able to differentiate behavior patterns that are time-intensive (e.g., rest, time & distance-intensive (e.g., area restricted search, and transit (short time and distance. We use grey-headed albatross (Thalassarche chrysostoma GPS tracks to demonstrate RST's ability to classify behavior patterns and adjust to the inherent scale and individuality of each track. Next, we evaluate RST's ability to discriminate between behavior states relative to other classical movement metrics. We then temporally sub-sample albatross track data to illustrate RST's response to less resolved data. Finally, we evaluate RST's performance using datasets from four taxa with diverse ecology, functional scales, ecosystems, and data-types. We conclude that RST is a robust, rapid, and flexible method for detailed exploratory analysis and meta-analyses of behavioral states in animal movement data based on its ability to integrate distance and time measurements into one descriptive metric of behavior groupings. Given the increasing amount of animal movement data collected, it is timely and useful to implement a consistent metric of behavior classification to enable efficient and comparative analyses. Overall, the application of RST to objectively explore and compare behavior patterns in

  11. The use of 41Ar to investigate residence time distribution (RTD) in petrochemical industry

    International Nuclear Information System (INIS)

    Sirelkhatim, D. A.; Hassan, B. A.; ElTayeb, M. A. H.; Hills, A. E.

    2004-01-01

    Residence time measurements were carried out on a wax slurry bed reactor (SBR) and on a pilot FTDU reactor by means of radioisotope tracer technology using Ar-41 as tracer gas. Representative results were obtained as the behaviour of the gas in the SBR showed channeling downstream and in the FTDU, possible different mixing zones in the upper portion and the occurrence of air pockets was evident. ( Authors)

  12. Extra-regional residence time as a correlate of plant invasiveness: European archaeophytes in North America

    Czech Academy of Sciences Publication Activity Database

    La Sorte, F. A.; Pyšek, Petr

    2009-01-01

    Roč. 90, č. 9 (2009), s. 2589-2597 ISSN 0012-9658 R&D Projects: GA MŠk LC06073 Grant - others:Evropská komise(XE) GOCE-CT-2003-506675 Institutional research plan: CEZ:AV0Z60050516 Keywords : residence time * archaeophyte * North America Subject RIV: EF - Botanics Impact factor: 4.411, year: 2009

  13. New residence times of the Holocene reworked shells on the west coast of Bohai Bay, China

    Science.gov (United States)

    Shang, Zhiwen; Wang, Fu; Li, Jianfen; Marshall, William A.; Chen, Yongsheng; Jiang, Xingyu; Tian, Lizhu; Wang, Hong

    2016-01-01

    Shelly cheniers and shell-rich beds found intercalated in near-shore marine muds and sandy sediments can be used to indicate the location of ancient shorelines, and help to estimate the height of sea level. However, dating the deposition of material within cheniers and shell-rich beds is not straightforward because much of this material is transported and re-worked, creating an unknown temporal off-set, i.e., the residence time, between the death of a shell and its subsequent entombment. To quantify the residence time during the Holocene on a section of the northern Chinese coastline a total 47 shelly subsamples were taken from 17 discrete layers identified on the west coast of Bohai Bay. This material was AMS 14C dated and the calibrated ages were systematically compared. The subsamples were categorized by type as articulated and disarticulated bivalves, gastropod shells, and undifferentiated shell-hash. It was found that within most individual layers the calibrated ages of the subsamples got younger relative to the amount of apparent post-mortem re-working the material had been subject to. For examples, the 14C ages of the bivalve samples trended younger in this order: shell-hash → split shells → articulated shells. We propose that the younger subsample age determined within an individual layer will be the closest to the actual depositional age of the material dated. Using this approach at four Holocene sites we find residence times which range from 100 to 1260 cal yrs, with two average values of 600 cal yrs for the original 14C dates older than 1 ka cal BP and 100 cal yrs for the original 14C dates younger than 1 ka cal BP, respectively. Using this semi-empirical estimation of the shell residence times we have refined the existing chronology of the Holocene chenier ridges on the west coast of Bohai Bay.

  14. Residence Time Distribution (RTD) Prediction in Mixing Vessel via CFD Simulation Using Fluent: An Overview

    International Nuclear Information System (INIS)

    Mohd Rizal Mamat; Azraf Azman; Noraishah Othman

    2011-01-01

    A prototype mixing vessel has been developed by Industrial Technology Division and installed at a multiphase testing facility in MINT Tech Park. A task to investigate the mixing vessel performance using Computational Fluid Dynamics (CFD) has been undertaken using the available FLUENT software in Malaysian Nuclear Agency. This paper discusses the modeling and simulation done in obtaining the Residence Time Distribution (RTD) for the mixing vessel using FLUENT. (author)

  15. Determination of the hydraulic residence time of two subsurface-flow constructed wetlands using radiotracers

    International Nuclear Information System (INIS)

    Debien, Bruno R.

    2013-01-01

    The adoption of constructed wetland systems (CW's) with subsuperficial drainage for sewage treatment is increasingly growing in places with low technological resources and available land. The efficient removal of pollutants depends on the internal flow characteristics in the CW and on its hydraulic residence time (HRT). In the present work 82 Br - a gamma radiation emitter, produced from soluble potassium bromide irradiated in the TRIGA reactor at the Centre for the Development of Nuclear Energy (CDTN) - was used as a pseudo-conservative tracer for the comparative study of aqueous phase flow dynamics in two CW's: one in which plants were grown (WP) whereas the other had no plants (WNP). Experimental hydraulic residence time values were found to be very close to the theoretical one, while dispersion numbers obtained for both CW's were quite small. Besides these measured hydrodynamic parameters, the residence time distribution (RTD) curves of the tracer test and the results of modeling of experimental data also demonstrate the tendency of the units to display a plug flow-like effluent hydraulic transport within their systems, as expected from their designs, considering the large length/width ratio (L/W=8). (author)

  16. Numerical modeling of general circulation, thermohaline structure, and residence time in Gorgan Bay, Iran

    Science.gov (United States)

    Ranjbar, Mohammad Hassan; Hadjizadeh Zaker, Nasser

    2018-01-01

    Gorgan Bay is a semi-enclosed basin located in the southeast of the Caspian Sea, Iran. The bay is recognized as a resting place for migratory birds as well as a spawning habitat for native fish. However, apparently, no detailed research on its physical processes has previously been conducted. In this study, a 3D coupled hydrodynamic and solute transport model was used to investigate general circulation, thermohaline structure, and residence time in Gorgan Bay. Model outputs were validated against a set of field observations. Bottom friction and attenuation coefficient of light intensity were tuned in order to achieve optimum agreement with the observations. Results revealed that, due to the interaction between bathymetry and prevailing winds, a barotropic double-gyre circulation, dominating the general circulation, existed during all seasons in Gorgan Bay. Furthermore, temperature and salinity fluctuations in the bay were seasonal, due to the seasonal variability of atmospheric fluxes. Results also indicated that under the prevailing winds, the domain-averaged residence time in Gorgan Bay would be approximately 95 days. The rivers discharging into Gorgan Bay are considered as the main sources of nutrients in the bay. Since their mouths are located in the area with a residence time of over 100 days, Gorgan Bay could be at risk of eutrophication; it is necessary to adopt preventive measures against water quality degradation.

  17. Impacts of residence time during storage on potential of water saving for grey water recycling system.

    Science.gov (United States)

    Liu, S; Butler, D; Memon, F A; Makropoulos, C; Avery, L; Jefferson, B

    2010-01-01

    Grey water recycling has been generally accepted and is about to move into practice in terms of sustainable development. Previous research has revealed the bacteria re-growth in grey water and reclaimed municipal water during storage. However, in most present grey water recycling practices, impacts of water quality changes during storage on the system's performance and design regulation have not been addressed. In this paper, performance of a constructed wetland based grey water recycling system was analysed by taking the constraint of residence time during storage into account using an object based household water cycle model. Two indicators, water saving efficiency (WSE) and residence time index (RTI), are employed to reflect the system's performance and residence time during storage respectively. Results show that WSE and RTI change with storage tank volumes oppositely. As both high WSE and RTI cannot be achieved simultaneously, it is concluded that in order to achieve the most cost-effective and safe solution, systems with both small grey and green tanks are needed, whilst accepting that only relatively modest water saving efficiency targets can be achieved. Higher efficiencies will only be practicable if water quality deterioration in the green water tank can be prevented by some means (e.g. disinfection).

  18. Residence time, native range size, and genome size predict naturalization among angiosperms introduced to Australia.

    Science.gov (United States)

    Schmidt, John P; Drake, John M; Stephens, Patrick

    2017-12-01

    Although critical to progress in understanding (i) if, and (ii) at what rate, introduced plants will naturalize and potentially become invasive, establishing causal links between traits and invasion success is complicated by data gaps, phylogenetic nonindependence of species, the inability to control for differences between species in residence time and propagule pressure, and covariance among traits. Here, we focus on statistical relationships between genomic factors, life history traits, native range size, and naturalization status of angiosperms introduced to Australia. In a series of analyses, we alternately investigate the role of phylogeny, incorporate introduction history, and use graphical models to explore the network of conditional probabilities linking traits and introduction history to naturalization status. Applying this ensemble of methods to the largest publicly available data set on plant introductions and their fates, we found that, overall, residence time and native range size best predicted probability of naturalization. Yet, importantly, probability of naturalization consistently increased as genome size decreased, even when the effects of shared ancestry and residence time in Australia were accounted for, and that this pattern was stronger in species without a history of cultivation, but present across annual-biennials, and herbaceous and woody perennials. Thus, despite introduction biases and indirect effects of traits via introduction history, across analyses, reduced genome size was nevertheless consistently associated with a tendency to naturalize.

  19. The relative importance of water temperature and residence time in predicting cyanobacteria abundance in regulated rivers.

    Science.gov (United States)

    Cha, YoonKyung; Cho, Kyung Hwa; Lee, Hyuk; Kang, Taegu; Kim, Joon Ha

    2017-11-01

    Despite a growing awareness of the problems associated with cyanobacterial blooms in rivers, and particularly in regulated rivers, the drivers of bloom formation and abundance in rivers are not well understood. We developed a Bayesian hierarchical model to assess the relative importance of predictors of summer cyanobacteria abundance, and to test whether the relative importance of each predictor varies by site, using monitoring data from 16 sites in the four major rivers of South Korea. The results suggested that temperature and residence time, but not nutrient levels, are important predictors of summer cyanobacteria abundance in rivers. Although the two predictors were of similar significance across the sites, the residence time was marginally better in accounting for the variation in cyanobacteria abundance. The model with spatial hierarchy demonstrated that temperature played a consistently significant role at all sites, and showed no effect from site-specific factors. In contrast, the importance of residence time varied significantly from site to site. This variation was shown to depend on the trophic state, indicated by the chlorophyll-a and total phosphorus levels. Our results also suggested that the magnitude of weir inflow is a key factor determining the cyanobacteria abundance under baseline conditions. Copyright © 2017 Elsevier Ltd. All rights reserved.

  20. Determination of the hydraulic residence time of two subsurface-flow constructed wetlands using radiotracers

    Energy Technology Data Exchange (ETDEWEB)

    Debien, Bruno R., E-mail: brunordebien@gmail.com [Universidade Federal de Minas Gerais (UFMG), Belo Horizonte, MG (Brazil). Dept de Geografia. Lab. de Geomorfologia; Barreto, Alberto A.; Pinto, Amenonia M.F.; Moreira, Rubens M., E-mail: aab@cdtn.br, E-mail: amfp@cdtn.br, E-mail: rubens@cdtn.br [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil)

    2013-07-01

    The adoption of constructed wetland systems (CW's) with subsuperficial drainage for sewage treatment is increasingly growing in places with low technological resources and available land. The efficient removal of pollutants depends on the internal flow characteristics in the CW and on its hydraulic residence time (HRT). In the present work {sup 82}Br - a gamma radiation emitter, produced from soluble potassium bromide irradiated in the TRIGA reactor at the Centre for the Development of Nuclear Energy (CDTN) - was used as a pseudo-conservative tracer for the comparative study of aqueous phase flow dynamics in two CW's: one in which plants were grown (WP) whereas the other had no plants (WNP). Experimental hydraulic residence time values were found to be very close to the theoretical one, while dispersion numbers obtained for both CW's were quite small. Besides these measured hydrodynamic parameters, the residence time distribution (RTD) curves of the tracer test and the results of modeling of experimental data also demonstrate the tendency of the units to display a plug flow-like effluent hydraulic transport within their systems, as expected from their designs, considering the large length/width ratio (L/W=8). (author)

  1. Estimating Estuarine Residence Times in the Westerschelde (the Netherlands) Using a Box Model with Fixed Dispersion Coefficients

    NARCIS (Netherlands)

    Soetaert, K.E.R.; Herman, P.M.J.

    1995-01-01

    The residence time of the water masses in the Westerschelde estuary was determined using a simple compartment-model that simulates the advective-diffusive transport of a conservative dissolved substance (chlorinity). The residence time of a water parcel in the upstream part of the estuary (i.e, the

  2. [Analysis on status and determinants of outpatient service utilization of rural floating population in Beijing at different residence time].

    Science.gov (United States)

    2017-06-18

    To study the status and identify the determinants of outpatient service utilization of rural floating population in Beijing who have different accumulated residence time. The survey data of rural floating population health and health care services in Beijing in 2014 were used, and the migrant population aged 18 years and above were taken as the research object. Whether to use outpatient service within two weeks was taken as dependent variable, gender, age, education level, self-assessment score of socioeconomic status, accumulated residence time in Beijing, health insurance, average household income, suffering from high blood pressure or diabetes as independent variables. Logistic regression model was used to analyze the influencing factors. The average age of the research object was 36.7 years, with mostly secondary education. The average accumulated residence time in Beijing was 8.4 years. The two-week prevalence rate was 10.3%, the two-week visiting rate calculated by person-time was 6.0%. The Logistic regression model suggested that, socioeconomic status, accumulated residence time and suffering from high blood pressure or diabetes were statistically significant determinants of outpatient service utilization. The research object is a younger and less educated population, their health status is better and outpatient service utilization is lower. It is found that people who have longer accumulated residence time in Beijing have lower outpatient service utilization. This is because people with longer residence time have lower age-adjusted two-week prevalence rate. This is also because people with longer residence time have larger proportion of taking continuous measures under doctor's advice. It does not mean people with longer residence time have lower utilization of medical service. The residence time variable plays the role of proxy variable. It can solve the problem of variables' endoge-neity. At the same time, it can reflect the influence to outpatient

  3. Probabilistic approach of water residence time and connectivity using Markov chains with application to tidal embayments

    Science.gov (United States)

    Bacher, C.; Filgueira, R.; Guyondet, T.

    2016-01-01

    Markov chain analysis was recently proposed to assess the time scales and preferential pathways into biological or physical networks by computing residence time, first passage time, rates of transfer between nodes and number of passages in a node. We propose to adapt an algorithm already published for simple systems to physical systems described with a high resolution hydrodynamic model. The method is applied to bays and estuaries on the Eastern Coast of Canada for their interest in shellfish aquaculture. Current velocities have been computed by using a 2 dimensional grid of elements and circulation patterns were summarized by averaging Eulerian flows between adjacent elements. Flows and volumes allow computing probabilities of transition between elements and to assess the average time needed by virtual particles to move from one element to another, the rate of transfer between two elements, and the average residence time of each system. We also combined transfer rates and times to assess the main pathways of virtual particles released in farmed areas and the potential influence of farmed areas on other areas. We suggest that Markov chain is complementary to other sets of ecological indicators proposed to analyse the interactions between farmed areas - e.g., depletion index, carrying capacity assessment. Markov chain has several advantages with respect to the estimation of connectivity between pair of sites. It makes possible to estimate transfer rates and times at once in a very quick and efficient way, without the need to perform long term simulations of particle or tracer concentration.

  4. Root microbiota dynamics of perennial Arabis alpina are dependent on soil residence time but independent of flowering time.

    Science.gov (United States)

    Dombrowski, Nina; Schlaeppi, Klaus; Agler, Matthew T; Hacquard, Stéphane; Kemen, Eric; Garrido-Oter, Ruben; Wunder, Jörg; Coupland, George; Schulze-Lefert, Paul

    2017-01-01

    Recent field and laboratory experiments with perennial Boechera stricta and annual Arabidopsis thaliana suggest that the root microbiota influences flowering time. Here we examined in long-term time-course experiments the bacterial root microbiota of the arctic-alpine perennial Arabis alpina in natural and controlled environments by 16S rRNA gene profiling. We identified soil type and residence time of plants in soil as major determinants explaining up to 15% of root microbiota variation, whereas environmental conditions and host genotype explain maximally 11% of variation. When grown in the same soil, the root microbiota composition of perennial A. alpina is largely similar to those of its annual relatives A. thaliana and Cardamine hirsuta. Non-flowering wild-type A. alpina and flowering pep1 mutant plants assemble an essentially indistinguishable root microbiota, thereby uncoupling flowering time from plant residence time-dependent microbiota changes. This reveals the robustness of the root microbiota against the onset and perpetual flowering of A. alpina. Together with previous studies, this implies a model in which parts of the root microbiota modulate flowering time, whereas, after microbiota acquisition during vegetative growth, the established root-associated bacterial assemblage is structurally robust to perturbations caused by flowering and drastic changes in plant stature.

  5. Simultaneous measurements of acetylene and soot during the pyrolysis of ethylene and benzene in a shock tube

    KAUST Repository

    KC, Utsav

    2016-10-12

    Acetylene is one of the most important precursors of soot and contributes to soot growth by the hydrogen-abstraction acetylene-addition (HACA) mechanism. In this work, we undertake time-resolved simultaneous measurements of acetylene and soot behind reflected shock waves at temperatures of 1600-2200. K and pressures of 3-5. bar. Acetylene mole fraction time-histories are measured from the absorption of a quantum-cascade laser operating around 13.6. μm. The soot volume fraction, particle size and number densities are calculated from the extinction and scattering of a cw Nd:Yag laser at 532. nm. Acetylene and soot are generated from the pyrolysis of 1% benzene in argon, 2.35% ethylene in argon, and binary mixtures of ethylene with propane/methane in argon. We note that acetylene time-histories exhibit a two-stage growth during the pyrolysis of benzene, which can be correlated to the initial rapid increase of soot volume fraction and a later plateauing. In comparison to ethylene pyrolysis, the pyrolysis of benzene results in larger values of the soot volume fraction, particle diameter and number density. We compare the measured data against the values simulated using the method-of-moments routine in Chemkin-Pro and a detailed PAH mechanism based on KM2 [1] and AramcoMech 1.3 [2]. Large discrepancies are observed between the measured and predicted values of the soot parameters. The data obtained from our experiments may assist future validation and development of soot mechanisms.

  6. Formation, growth, and transport of soot in a three-dimensional turbulent non-premixed jet flame

    KAUST Repository

    Attili, Antonio

    2014-07-01

    The formation, growth, and transport of soot is investigated via large scale numerical simulation in a three-dimensional turbulent non-premixed n-heptane/air jet flame at a jet Reynolds number of 15,000. For the first time, a detailed chemical mechanism, which includes the soot precursor naphthalene and a high-order method of moments are employed in a three-dimensional simulation of a turbulent sooting flame. The results are used to discuss the interaction of turbulence, chemistry, and the formation of soot. Compared to temperature and other species controlled by oxidation chemistry, naphthalene is found to be affected more significantly by the scalar dissipation rate. While the mixture fraction and temperature fields show fairly smooth spatial and temporal variations, the sensitivity of naphthalene to turbulent mixing causes large inhomogeneities in the precursor fields, which in turn generate even stronger intermittency in the soot fields. A strong correlation is apparent between soot number density and the concentration of naphthalene. On the contrary, while soot mass fraction is usually large where naphthalene is present, pockets of fluid with large soot mass are also frequent in regions with very low naphthalene mass fraction values. From the analysis of Lagrangian statistics, it is shown that soot nucleates and grows mainly in a layer close to the flame and spreads on the rich side of the flame due to the fluctuating mixing field, resulting in more than half of the total soot mass being located at mixture fractions larger than 0.6. Only a small fraction of soot is transported towards the flame and is completely oxidized in the vicinity of the stoichiometric surface. These results show the leading order effects of turbulent mixing in controlling the dynamics of soot in turbulent flames. Finally, given the difficulties in obtaining quantitative data in experiments of turbulent sooting flames, this simulation provides valuable data to guide the development of

  7. Method for Making Measurements of the Post-Combustion Residence Time in a Gas Turbine Engine

    Science.gov (United States)

    Miles, Jeffrey H. (Inventor)

    2017-01-01

    A method of measuring a residence time in a gas-turbine engine is disclosed that includes measuring a combustor pressure signal at a combustor entrance and a turbine exit pressure signal at a turbine exit. The method further includes computing a cross-spectrum function between the combustor pressure signal and the turbine exit pressure signal, calculating a slope of the cross-spectrum function, shifting the turbine exit pressure signal an amount corresponding to a time delay between the measurement of the combustor pressure signal and the turbine exit pressure signal, and recalculating the slope of the cross-spectrum function until the slope reaches zero.

  8. Numerical investigation on soot particles emission in compression ignition diesel engine by using particulate mimic soot model

    Directory of Open Access Journals (Sweden)

    Ibrahim Fadzli

    2017-01-01

    Full Text Available Research via computational method, specifically by detailed-kinetic soot model offers much more advantages than the simple model as more detailed formation/oxidation process is taken into consideration, thus providing better soot mass concentration, soot size, soot number density as well as information regarding other related species. In the present computational study, investigation of in-cylinder soot concentration as well as other emissions in a single cylinder diesel engine has been conducted, using a commercial multidimensional CFD software, CONVERGE CFD. The simulation was carried out for a close-cycle combustion environment from inlet valve closing (IVC to exhaust valve opening (EVO. In this case, detailed-kinetic Particulate Mimic (PM soot model was implemented as to take benefit of the method of moment, instead of commonly implemented simple soot model. Analyses of the results are successfully plotted to demonstrate that the soot size and soot mass concentration are strongly dependent on the detailed soot formation and oxidation process rates. The calculated of soot mass concentration and average soot size at EVO provide the end value of 29.2 mg/m3 and 2.04 × 10−8 m, respectively. Besides, post-processing using EnSight shows the qualitative results of soot concentration along simulation period in the combustion chamber.

  9. Th effectiveness of soot removal techniques for the recovery of fingerprints on glass fire debris in petrol bomb cases

    International Nuclear Information System (INIS)

    Umi Kalthom Ahmad; Mei, Y.S.; Mohd Shahru Bahari; Raramasivam, V.K.

    2011-01-01

    The increased use of petrol bombs as an act of vengeance in Malaysia has heightened awareness for the need of research relating physical evidence found at the crime scene to the perpetrator of the crime. A study was therefore carried out to assess the effectiveness of soot removal techniques on glass fire debris without affecting the fingerprints found on the evidence. Soot was removed using three methods which were brushing, 2 % NaOH solution and tape lifting. Depending on the visibility of prints recovered, prints which were visible after soot removal were lifted directly while prints that were not visible were subjected to enhancement. Glass microscope slides were used in laboratory experiment and subjected to control burn for the formation of soot. Soot was later removed following enhancement of the prints over time (within 1 day, within 2 days and after 2 days). While in simulated petrol bomb ground experiment, petrol bombs were hurled in glass bottles and the fragments were collected. Favorable results were obtained in varying degrees using each soot removal methods. In laboratory testing, brushing and 2 % NaOH solution revealed fingerprints that were visible after removal of excess soot and were lifted directly. As for tape lifting technique, some prints were visible and were successfully lifted while those that were not visible were subjected to super glue fuming for effective fingerprint identification. (author)

  10. Ultra-small-angle X-ray scattering characterization of diesel/gasoline soot: sizes and particle-packing conditions

    Science.gov (United States)

    Kameya, Yuki; Lee, Kyeong O.

    2013-10-01

    Regulations on particulate emissions from internal combustion engines tend to become more stringent, accordingly the importance of particulate filters in the after-treatment system has been increasing. In this work, the applicability of ultra-small-angle X-ray scattering (USAXS) to diesel soot cake and gasoline soot was investigated. Gasoline-direct-injection engine soot was collected at different fuel injection timings. The unified fits method was applied to analyze the resultant scattering curves. The validity of analysis was supported by comparing with carbon black and taking the sample images using a transmission electron microscope, which revealed that the primary particle size ranged from 20 to 55 nm. In addition, the effects of particle-packing conditions on the USAXS measurement were demonstrated by using samples suspended in acetone. Then, the investigation was extended to characterization of diesel soot cake deposited on a diesel particulate filter (DPF). Diesel soot was trapped on a small piece of DPF at different deposition conditions which were specified using the Peclet number. The dependence of scattering curve on soot-deposition conditions was demonstrated. To support the interpretation of the USAXS results, soot cake samples were observed using a scanning electron microscope and the influence of particle-packing conditions on scattering curve was discussed.

  11. Ultra-small-angle X-ray scattering characterization of diesel/gasoline soot: sizes and particle-packing conditions

    International Nuclear Information System (INIS)

    Kameya, Yuki; Lee, Kyeong O.

    2013-01-01

    Regulations on particulate emissions from internal combustion engines tend to become more stringent, accordingly the importance of particulate filters in the after-treatment system has been increasing. In this work, the applicability of ultra-small-angle X-ray scattering (USAXS) to diesel soot cake and gasoline soot was investigated. Gasoline-direct-injection engine soot was collected at different fuel injection timings. The unified fits method was applied to analyze the resultant scattering curves. The validity of analysis was supported by comparing with carbon black and taking the sample images using a transmission electron microscope, which revealed that the primary particle size ranged from 20 to 55 nm. In addition, the effects of particle-packing conditions on the USAXS measurement were demonstrated by using samples suspended in acetone. Then, the investigation was extended to characterization of diesel soot cake deposited on a diesel particulate filter (DPF). Diesel soot was trapped on a small piece of DPF at different deposition conditions which were specified using the Peclet number. The dependence of scattering curve on soot-deposition conditions was demonstrated. To support the interpretation of the USAXS results, soot cake samples were observed using a scanning electron microscope and the influence of particle-packing conditions on scattering curve was discussed

  12. Delayed condensation and frost formation on superhydrophobic carbon soot coatings by controlling the presence of hydrophilic active sites

    Science.gov (United States)

    Esmeryan, Karekin D.; Castano, Carlos E.; Mohammadi, Reza; Lazarov, Yuliyan; Radeva, Ekaterina I.

    2018-02-01

    Condensation frosting is an undesired natural phenomenon that could be impeded efficiently using appropriate wettability and morphologically patterned surfaces. The icephobic properties of carbon soot and the fabrication scalability of its synthesis method are a good foundation for anti-frosting applications; however, the fundamentals of frost growth and spreading on sooted surfaces have not been examined yet. In this study, we investigate the anti-frosting performance of three groups of superhydrophobic soot coatings by means of 16 MHz quartz crystal microbalances (QCMs). The analysis of the real-time sensor signal of each soot coated QCM pattern shows that frost formation and its propagation velocity depend on the quantity of oxygen functionalities and structural defects in the material. In turn, the reduction of both parameters shifts the onset of frost growth to temperatures below  -20 °C, whereas the interdroplet ice bridging is slowed by a factor of four. Moreover, high-resolution scanning electron micrographs of the samples imply delamination upon defrosting of the soot with spherical-like morphology via polar interactions driven mechanism. These results reveal an opportunity for control of frost incipiency on sooted surfaces by adjusting the synthesis conditions and depositing soot coatings with as low as possible content of hydrophilic active sites.

  13. Mucoadhesive nano-sized supramolecular assemblies for improved pre-corneal drug residence time.

    Science.gov (United States)

    Fabiano, Angela; Chetoni, Patrizia; Zambito, Ylenia

    2015-01-01

    Mucoadhesive nanoparticles were compared with non-aggregated constituent polymers for effect on pre-corneal residence of dexamethasone phosphate (DP) or met-enkephalin (ME), administered by eye-drops to rabbits. Deepening the knowledge of ophthalmic nanoparticulate systems in terms of ability to prolong pre-corneal residence. Medicated nanoparticles resulted from gelation of quaternary ammonium-chitosan conjugate or its thiolated derivative with hyaluronan in the presence of drug. Particles were analyzed by light scattering. Dialysis removed non-encapsulated drug, dynamic dialysis measured drug-polymer interactions, and lyophilization-stabilized product. Dispersions were regenerated from lyophilized products. Also solutions of non-thiolated or thiolated chitosan derivative were administered. Mean drug residence time (MRT) in tears was determined by collecting samples from lower marginal tear strip of albino rabbits using capillaries. Nanoparticle size of regenerated dispersions was 400-430 nm (DP-systems), 360-370 nm (ME-systems); the drug content was 2.5 mg/mL (DP) or 0.3 mg/mL (ME). The MRT for DP nanoparticles from non-thiolated derivative was higher than that for non-aggregated polymer, due to stronger concurrent interactions of positively charged nanoparticles with ocular surface and drug. Thiolated polymer nanoparticles and non-aggregated parent polymer, both interacting weakly with DP, showed similar MRT values. The MRT of ME could only be enhanced by protecting drug from enzymatic hydrolysis. This was done by nanoparticle systems, whereas non-aggregated polymers were ineffective. Developing a nanoparticle system rather than a solution of mucoadhesive polymer, for prolonging pre-corneal residence, is convenient, provided nanoparticles interact strongly with both ocular surface and drug, or protect drug from metabolic degradation.

  14. Compositional effects on PAH and soot formation in counterflow diffusion flames of gasoline surrogate fuels

    KAUST Repository

    Park, Sungwoo

    2017-02-05

    Gasoline surrogate fuels are widely used to understand the fundamental combustion properties of complex refinery gasoline fuels. In this study, the compositional effects on polycyclic aromatic hydrocarbons (PAHs) and soot formation were investigated experimentally for gasoline surrogate mixtures comprising n-heptane, iso-octane, and toluene in counterflow diffusion flames. A comprehensive kinetic model for the gasoline surrogate mixtures was developed to accurately predict the fuel oxidation along with the formation of PAHs and soot in flames. This combined model was first tested against ignition delay times and laminar burning velocities data. The proposed model for the formation and growth of PAHs up to coronene (C24H12) was based on previous studies and was tested against existing and present new experimental data. Additionally, in the accompanied soot model, PAHs with sizes larger than (including) pyrene were used for the inception of soot particles, followed by particle coagulations and PAH condensation/chemical reactions on soot surfaces. The major pathways for the formation of PAHs were also identified for the surrogate mixtures. The model accurately captures the synergistic PAH formation characteristics observed experimentally for n-heptane/toluene and iso-octane/toluene binary mixtures. Furthermore, the present experimental and modeling results also elucidated different trends in the formation of larger PAHs and soot between binary n-heptane/iso-octane and ternary n-heptane/iso-octane/toluene mixtures. Propargyl radicals (C3H3) were shown to be important in the formation and growth of PAHs for n-heptane/iso-octane mixtures when the iso-octane concentration increased; however, reactions involving benzyl radicals (C6H5CH2) played a significant role in the formation of PAHs for n-heptane/iso-octane/toluene mixtures. These results indicated that the formation of PAHs and subsequently soot was strongly affected by the composition of gasoline surrogate mixtures.

  15. Kinetics and mechanism of soot formation in hydrocarbon combustion

    Science.gov (United States)

    Frenklach, Michael

    1990-01-01

    The focus of this work was on kinetic modeling. The specific objectives were: detailed modeling of soot formation in premixed flames, elucidation of the effects of fuel structure on the pathway to soot, and the development of a numerical technique for accurate modeling of soot particle coagulation and surface growth. Those tasks were successfully completed and are briefly summarized.

  16. Soot precursor measurements in benzene and hexane diffusion flames

    Energy Technology Data Exchange (ETDEWEB)

    Kobayashi, Y.; Furuhata, T.; Amagai, K.; Arai, M. [Department of Mechanical System Engineering, Graduate School of Engineering, Gunma University, 1-5-1 Tenjin-cho, Kiryu-shi, Gunma 376-8515 (Japan)

    2008-08-15

    To clarify the mechanism of soot formation in diffusion flames of liquid fuels, measurements of soot and its precursors were carried out. Sooting diffusion flames formed by a small pool combustion equipment system were used for this purpose. Benzene and hexane were used as typical aromatic and paraffin fuels. A laser-induced fluorescence (LIF) method was used to obtain spatial distributions of polycyclic aromatic hydrocarbons (PAHs), which are considered as soot particles. Spatial distributions of soot in test flames were measured by a laser-induced incandescence (LII) method. Soot diameter was estimated from the temporal change of LII intensity. A region of transition from PAHs to soot was defined from the results of LIF and LII. Flame temperatures, PAH species, and soot diameters in this transition region were investigated for both benzene and hexane flames. The results show that though the flame structures of benzene and hexane were different, the temperature in the PAHs-soot transition region of the benzene flame was similar to that of the hexane flame. Furthermore, the relationship between the PAH concentrations measured by gas chromatography in both flames and the PAH distributions obtained from LIF are discussed. It was found that PAHs with smaller molecular mass, such as benzene and toluene, remained in both the PAHs-soot transition and sooting regions, and it is thought that molecules heavier than pyrene are the leading candidates for soot precursor formation. (author)

  17. Fractional-time random walk subdiffusion and anomalous transport with finite mean residence times: faster, not slower.

    Science.gov (United States)

    Goychuk, Igor

    2012-08-01

    Continuous time random walk (CTRW) subdiffusion along with the associated fractional Fokker-Planck equation (FFPE) is traditionally based on the premise of random clock with divergent mean period. This work considers an alternative CTRW and FFPE description which is featured by finite mean residence times (MRTs) in any spatial domain of finite size. Transient subdiffusive transport can occur on a very large time scale τ(c) which can greatly exceed mean residence time in any trap, τ(c) >(τ), and even not being related to it. Asymptotically, on a macroscale transport becomes normal for t > τ(c). However, mesoscopic transport is anomalous. Differently from viscoelastic subdiffusion no long-range anticorrelations among position increments are required. Moreover, our study makes it obvious that the transient subdiffusion and transport are faster than one expects from their normal asymptotic limit on a macroscale. This observation has profound implications for anomalous mesoscopic transport processes in biological cells because the macroscopic viscosity of cytoplasm is finite.

  18. Flow and Residence Times of Dynamic River Bank Storage and Sinuosity-Driven Hyporheic Exchange

    Science.gov (United States)

    Gomez-Velez, J. D.; Wilson, J. L.; Cardenas, M. B.; Harvey, J. W.

    2017-10-01

    Hydrologic exchange fluxes (HEFs) vary significantly along river corridors due to spatiotemporal changes in discharge and geomorphology. This variability results in the emergence of biogeochemical hot-spots and hot-moments that ultimately control solute and energy transport and ecosystem services from the local to the watershed scales. In this work, we use a reduced-order model to gain mechanistic understanding of river bank storage and sinuosity-driven hyporheic exchange induced by transient river discharge. This is the first time that a systematic analysis of both processes is presented and serves as an initial step to propose parsimonious, physics-based models for better predictions of water quality at the large watershed scale. The effects of channel sinuosity, alluvial valley slope, hydraulic conductivity, and river stage forcing intensity and duration are encapsulated in dimensionless variables that can be easily estimated or constrained. We find that the importance of perturbations in the hyporheic zone's flux, residence times, and geometry is mainly explained by two-dimensionless variables representing the ratio of the hydraulic time constant of the aquifer and the duration of the event (Γd) and the importance of the ambient groundwater flow (Δh∗). Our model additionally shows that even systems with small sensitivity, resulting in small changes in the hyporheic zone extent, are characterized by highly variable exchange fluxes and residence times. These findings highlight the importance of including dynamic changes in hyporheic zones for typical HEF models such as the transient storage model.

  19. Residence time and movements of postbreeding shorebirds on the northern coast of Alaska

    Science.gov (United States)

    Taylor, Audrey R.; Lanctot, Richard B.; Powell, Abby N.; Kendall, Steven J.; Nigro, Debora A.

    2011-01-01

    Relatively little is known about shorebird movements across the coast of northern Alaska, yet postbreeding shorebirds use this coastline extensively prior to fall migration. We deployed 346 radio transmitters on 153 breeding and 193 postbreeding shorebirds of five species from 2005 to 2007.We examined two hypotheses regarding postbreeding shorebirds' movements: (1) whether such movements reflect ultimate routes of southbound migration and (2) whether migration strategy (length of flights) or timing of molt in relation to migration (molt occurring in breeding or winter range) are more influential in determining postbreeding shorebirds' behavior. Semipalmated Sandpipers (Calidris pusilla) moved east, consistent with the direction of their ultimate migration, but patterns of other species' movements did not reflect ultimate migration direction. Timing of postnuptial molt appeared to have more influence over residence time and movements than did migration strategy. Postcapture residence time for the Semipalmated Sandpiper was less than for the Western Sandpiper (C. mauri) and significantly less than for Dunlin (C. alpina), and the Semipalmated Sandpiper's movements between were quicker and more frequent than those of the Dunlin. We expected to see the opposite patterns if migration strategy were more influential. Our data shed light on how different shorebird species use the northern Alaska coast after breeding: most species are likely to be stopping over at postbreeding areas, whereas the Dunlin and some Western Sandpipers may be staging. We suggest the coast of northern Alaska be viewed as an interconnected network of postbreeding sites that serve multiple populations of breeding shorebirds.

  20. Structure and Composition of Air-Plane Soots and Surrogates Analyzed by Raman Spectroscopy and Laser/Ions Desorption Mass Spectrometry

    Science.gov (United States)

    Ortega, Ismael; Chazallon, Bertrand; Carpentier, Yvain; Irimiea, Cornelia; Focsa, Cristian; Ouf, François-Xavier; Salm, François; Delhaye, David; Gaffié, Daniel; Yon, Jérôme

    2015-04-01

    Aviation alters the composition of the atmosphere globally and can thus drive climate change and ozone depletion [1]. An aircraft exhaust plume contains species emitted by the engines, species formed in the plume from the emitted species and atmospheric species that become entrained into the plume. The majority of emitted species (gases and soot particles) are produced by the combustion of kerosene with ambient air in the combustion chamber of the engine. Emissions of soot particles by air-planes produce persistent contrails in the upper troposphere in ice-supersaturated air masses that contribute to cloudiness and impact the radiative properties of the atmosphere. These aerosol-cloud interactions represent one of the largest sources of uncertainty in global climate models [2]. Though the formation of atmospheric ice particles has been studied since many years [3], there are still numerous opened questions on nucleation properties of soot particles [4], as the ice nucleation experiments showed a large spread in results depending on the nucleation mode chosen and origin of the soot produced. Most likely one of the reasons behind these discrepancies resides in the different physico-chemical properties (composition, structure) of soot particles produced in different conditions, e.g. with respect to fuel or combustion techniques. In this work, we use Raman microscopy (266, 514 and 785 nm excitation) and ablation techniques (SIMS, Secondary Ions Mass Spectrometry, and Laser Desorption Mass Spectrometry) to characterize soot particles produced from air-plane at different engine regimes simulating a landing and taking-off (LTO) cycle. First, the spectral parameters of the first-order Raman band of various soot samples, collected from three different sources in the frame of the MERMOSE project (http://mermose.onera.fr/): PowerJet SaM-146 turbofan (four engine regimes), CAST generator (propane fuel, four different global equivalence ratios), and Kerosene laboratory flame

  1. Spatial distribution of triazine residues in a shallow alluvial aquifer linked to groundwater residence time.

    Science.gov (United States)

    Sassine, Lara; Le Gal La Salle, Corinne; Khaska, Mahmoud; Verdoux, Patrick; Meffre, Patrick; Benfodda, Zohra; Roig, Benoît

    2017-03-01

    At present, some triazine herbicides occurrence in European groundwater, 13 years after their use ban in the European Union, remains of great concern and raises the question of their persistence in groundwater systems due to several factors such as storage and remobilization from soil and unsaturated zone, limited or absence of degradation, sorption in saturated zones, or to continuing illegal applications. In order to address this problem and to determine triazine distribution in the saturated zone, their occurrence is investigated in the light of the aquifer hydrodynamic on the basis of a geochemical approach using groundwater dating tracers ( 3 H/ 3 He). In this study, atrazine, simazine, terbuthylazine, deethylatrazine, deisopropylatrazine, and deethylterbuthylazine are measured in 66 samples collected between 2011 and 2013 from 21 sampling points, on the Vistrenque shallow alluvial aquifer (southern France), covered by a major agricultural land use. The frequencies of quantification range from 100 to 56 % for simazine and atrazine, respectively (LQ = 1 ng L -1 ). Total triazine concentrations vary between 15 and 350 ng L -1 and show three different patterns with depth below the water table: (1) low concentrations independent of depth but related to water origin, (2) an increase in concentrations with depth in the aquifer related to groundwater residence time and triazine use prior to their ban, and (3) relatively high concentrations at low depths in the saturated zone more likely related to a slow desorption of these compounds from the soil and unsaturated zone. The triazine attenuation rate varies between 0.3 for waters influenced by surface water infiltration and 4.8 for water showing longer residence times in the aquifer, suggesting an increase in these rates with water residence time in the saturated zone. Increasing triazine concentrations with depth is consistent with a significant decrease in the use of these pesticides for the last 10 years on

  2. Numerical and machine learning simulation of parametric distributions of groundwater residence time in streams and wells

    Science.gov (United States)

    Starn, J. J.; Belitz, K.; Carlson, C.

    2017-12-01

    Groundwater residence-time distributions (RTDs) are critical for assessing susceptibility of water resources to contamination. This novel approach for estimating regional RTDs was to first simulate groundwater flow using existing regional digital data sets in 13 intermediate size watersheds (each an average of 7,000 square kilometers) that are representative of a wide range of glacial systems. RTDs were simulated with particle tracking. We refer to these models as "general models" because they are based on regional, as opposed to site-specific, digital data. Parametric RTDs were created from particle RTDs by fitting 1- and 2-component Weibull, gamma, and inverse Gaussian distributions, thus reducing a large number of particle travel times to 3 to 7 parameters (shape, location, and scale for each component plus a mixing fraction) for each modeled area. The scale parameter of these distributions is related to the mean exponential age; the shape parameter controls departure from the ideal exponential distribution and is partly a function of interaction with bedrock and with drainage density. Given the flexible shape and mathematical similarity of these distributions, any of them are potentially a good fit to particle RTDs. The 1-component gamma distribution provided a good fit to basin-wide particle RTDs. RTDs at monitoring wells and streams often have more complicated shapes than basin-wide RTDs, caused in part by heterogeneity in the model, and generally require 2-component distributions. A machine learning model was trained on the RTD parameters using features derived from regionally available watershed characteristics such as recharge rate, material thickness, and stream density. RTDs appeared to vary systematically across the landscape in relation to watershed features. This relation was used to produce maps of useful metrics with respect to risk-based thresholds, such as the time to first exceedance, time to maximum concentration, time above the threshold

  3. The muddle of ages, turnover, transit, and residence times in the carbon cycle.

    Science.gov (United States)

    Sierra, Carlos A; Müller, Markus; Metzler, Holger; Manzoni, Stefano; Trumbore, Susan E

    2017-05-01

    Comparisons among ecosystem models or ecosystem dynamics along environmental gradients commonly rely on metrics that integrate different processes into a useful diagnostic. Terms such as age, turnover, residence, and transit times are often used for this purpose; however, these terms are variably defined in the literature and in many cases, calculations ignore assumptions implicit in their formulas. The aim of this opinion piece was i) to make evident these discrepancies and the incorrect use of formulas, ii) highlight recent results that simplify calculations and may help to avoid confusion, and iii) propose the adoption of simple and less ambiguous terms. © 2016 John Wiley & Sons Ltd.

  4. Stable isotope fractionation in response to variable fluid residence time distributions

    Science.gov (United States)

    Druhan, J. L.; Maher, K.

    2013-12-01

    Hydrogeochemical processes governing groundwater quantity and quality are often inferred from fluid samples that are the flux-weighted average of a heterogeneous system. This connection has been demonstrated for solutes subject to transport and equilibrium constraints, in which the steady state concentration - discharge relationship is cast in terms of the choice of expression for residence time distribution (Maher, 2011). Here, we examine the extent to which the spatial correlation of the permeability field, which governs the fluid residence time distribution, exerts a principle control on the partitioning of stable isotopes between reactant and product species during heterogeneous reactions in groundwater systems. We demonstrate this relationship using numerical simulations of δ53Cr fractionation due to abiotic CrO42- reduction by Fe2+, implemented in the reactive transport code CrunchFlow. The chemically homogeneous redox reaction generates Cr3+ with an isotope ratio distinct from the reactant pool, and in turn this product species precipitates as a mineral phase Cr(OH)3(s) through a non-fractionating reaction. The corresponding chromate δ53Cr enrichment across a homogeneous domain varies from a maximum value set by the kinetic fractionation factor (αk) at high mean fluid residence times, to a value reaction-limited to transport-limited regimes. For physically heterogeneous flow fields, the transition in isotopic fractionation from a reaction-limited to a transport-limited regime becomes variable, and falls between the upper and lower bounds set by the homogeneous simulations at slow and fast precipitation rates, respectively. Our results show that while minimal variation occurs in the steady-state isotopic profile of the reactant species (δ53Cr of CrO42-), the combined effects of the precipitation rate and the heterogeneous structure of the porous media lead to a wide range in the steady state isotopic composition of the product species (δ53Cr of Cr3

  5. Evaluation of a Lagrangian Soot Tracking Method for the prediction of primary soot particle size under engine-like conditions

    DEFF Research Database (Denmark)

    Cai Ong, Jiun; Pang, Kar Mun; Walther, Jens Honore

    2018-01-01

    particles when the mass of incipient soot exceeds a designated threshold value. Their trajectories are then computed using the particle momentum equation. The change of primary soot particle size is dependent on the modified Lagrangian surface growth and soot oxidation models. Performance of the LST model...

  6. The many faces of soot: characterization of soot nanoparticles produced by engines.

    Science.gov (United States)

    Niessner, Reinhard

    2014-11-10

    Soot nanoparticles produced by engines constitute a threat to human health. For the analytical chemist, soot is a hard nut to crack as the released particles undergo rapid changes in their size, shape, and number concentration. The complete characterization of soot will be essential to meet future low-emission standards. Besides measuring the light extinction, modern analytical chemistry can determine a variety of less-known effects, such as condensation properties, immune response in vertebrates, and impact on the cardiovascular function of a beating heart. Photon emission and in particular Raman spectroscopy provides information on the nanocrystallinity, while thermoelectron emission allows the number of electrical particles to be counted. Even the "simple" combustion of soot nanoparticles offers potential for the characterization of the particles. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  7. Using just-in-time teaching and peer instruction in a residency program's core curriculum: enhancing satisfaction, engagement, and retention.

    Science.gov (United States)

    Schuller, Mary C; DaRosa, Debra A; Crandall, Marie L

    2015-03-01

    To assess use of the combined just-in-time teaching (JiTT) and peer instruction (PI) instructional strategy in a residency program's core curriculum. In 2010-2011, JiTT/PI was piloted in 31 core curriculum sessions taught by 22 faculty in the Northwestern University Feinberg School of Medicine's general surgery residency program. JiTT/PI required preliminary and categorical residents (n=31) to complete Web-based study questions before weekly specialty topic sessions. Responses were examined by faculty members "just in time" to tailor session content to residents' learning needs. In the sessions, residents answered multiple-choice questions (MCQs) using clickers and engaged in PI. Participants completed surveys assessing their perceptions of JiTT/PI. Videos were coded to assess resident engagement time in JiTT/PI sessions versus prior lecture-based sessions. Responses to topic session MCQs repeated in review sessions were evaluated to study retention. More than 70% of resident survey respondents indicated that JiTT/PI aided in the learning of key points. At least 90% of faculty survey respondents reported positive perceptions of aspects of the JiTT/PI strategy. Resident engagement time for JiTT/PI sessions was significantly greater than for prior lecture-based sessions (z=-2.4, P=.016). Significantly more review session MCQ responses were correct for residents who had attended corresponding JiTT/PI sessions than for residents who had not (chi-square=13.7; df=1; P<.001). JiTT/PI increased learner participation, learner retention, and the amount of learner-centered time. JiTT/PI represents an effective approach for meaningful and active learning in core curriculum sessions.

  8. The Status of Social and Leisure Time Activities in the Elderly Residing In Iran and Sweden

    Directory of Open Access Journals (Sweden)

    Seyed Bagher Madah

    2008-07-01

    Full Text Available Objectives: Among social determinants of health, culture and ethnicity play a key role in defining the needs of different population groups. The aim of this study was to consider and compare the social and leisure time activities of the three elderly groups: Iranian residing in Iran, Iranian residing in Sweden and Swedish residing in Sweden. Methods & Materials: Via the cross-sectional design, 825 Iranian elderly who were living in Tehran compared with 305 Swedish elderly and 101 Iranian elderly living in Stockholm on social relations, group activities and leisure time activities. Only, elderly who could communicate properly entered the study. A structured questionnaire designed by the Iranian and Swedish Research Group on the" Assessment of Social Health Status and Needs" implemented for the subjects. Estimation method and logistic regression used to analyze the gathered data. Results: Subjects of all 3 groups were in the age range of 60-77 years old and mostly were married. Results showed despite very common characteristics, there are, also, many differences which can be explained by cultural and environmental factors. Rapid urbanization, limited resources and unawareness of or disregard for healthy life style resulted in lower levels of satisfaction with social and leisure life in the Iranian elderly. On the other hand, level of activities related to the spiritual dimension of health were more in Iranians than Swedish and the difference was significant (P=0.000, whereas the reverse was true for the group activities (P=0.000. Poor attitude toward physical activity and exercise in Iranian elderly, especially women, with consequent hazards for health, needs special consideration on behalf of the health planners and providers. Conclusion: Needs assessment with trance- cultural approach, especially on social determinants of the health of elderly is a necessity. Using valid and reliable instruments, designed to overcome the cultural barriers would

  9. Keeping up with the times: revising the dermatology residency curriculum in the era of molecular diagnostics and personalized medicine.

    Science.gov (United States)

    LaChance, Avery; Murphy, Michael J

    2014-11-01

    The clinical use of molecular diagnostics, genomics, and personalized medicine is increasing and improving rapidly over time. However, medical education incorporating the practical application of these techniques is lagging behind. Although instruction in these areas should be expanded upon and improved at all levels of training, residency provides a concentrated period of time in which to hone in on skills that are practically applicable to a trainee's specialty of choice. Although residencies in some fields, such as pathology, have begun to incorporate practical molecular diagnostics training, this area remains a relative gap in dermatology residency programs. Herein, we advocate for the incorporation of training in molecular diagnostics and personalized medicine into dermatology residency programs and propose a basic curriculum template for how to begin approaching these topics. By incorporating molecular diagnostics into dermatology residency training, dermatologists have the opportunity to lead the way and actively shape the specialty's transition into the era of personalized medicine. © 2014 The International Society of Dermatology.

  10. Macrotextured spoked surfaces reduce the residence time of a bouncing Leidenfrost drop

    Science.gov (United States)

    Patterson, Colin J.; Shiri, Samira; Bird, James C.

    2017-02-01

    Liquid drops can bounce when they impact non-wetting surfaces. Recently, studies have demonstrated that the time that the bouncing drop contacts a superhydrophobic surface can be reduced by incorporating ridged macrotextures on the surface. Yet the existing models aimed at explaining this phenomenon offer incompatible predictions of the contact time when a drop impacts multiple intersecting macrotextures, or spokes. Furthermore, it is unclear whether the effects of the macrotexture on the drop hydrodynamics extend to non-wetting surfaces in which direct contact is avoided by a thin vapor layer. Here we demonstrate that the phenomenon observed for macrotextured, superhydrophobic surfaces extends to macrotextured, wettable surfaces above the Leidenfrost temperature. We show that the number of droplets and overall residence time both depend on the number of intersecting spokes. Finally, we compare and contrast our results with mechanistic models to rationalize various elements of the phenomenon.

  11. Soot and Spectral Radiation Modeling for a High-Pressure Turbulent Spray Flame

    Energy Technology Data Exchange (ETDEWEB)

    Ferreryo-Fernandez, Sebastian [Pennsylvania State Univ., University Park, PA (United States); Paul, Chandan [Pennsylvania State Univ., University Park, PA (United States); Sircar, Arpan [Pennsylvania State Univ., University Park, PA (United States); Imren, Abdurrahman [Pennsylvania State Univ., University Park, PA (United States); Haworth, Daniel C [Pennsylvania State Univ., University Park, PA (United States); Roy, Somesh P [Marquette University (United States); Modest, Michael F [University of California Merced (United States)

    2017-04-26

    Simulations are performed of a transient high-pressure turbulent n-dodecane spray flame under engine-relevant conditions. An unsteady RANS formulation is used, with detailed chemistry, a semi-empirical two-equation soot model, and a particle-based transported composition probability density function (PDF) method to account for unresolved turbulent fluctuations in composition and temperature. Results from the PDF model are compared with those from a locally well-stirred reactor (WSR) model to quantify the effects of turbulence-chemistry-soot interactions. Computed liquid and vapor penetration versus time, ignition delay, and flame lift-off height are in good agreement with experiment, and relatively small differences are seen between the WSR and PDF models for these global quantities. Computed soot levels and spatial soot distributions from the WSR and PDF models show large differences, with PDF results being in better agreement with experimental measurements. An uncoupled photon Monte Carlo method with line-by-line spectral resolution is used to compute the spectral intensity distribution of the radiation leaving the flame. This provides new insight into the relative importance of molecular gas radiation versus soot radiation, and the importance of turbulent fluctuations on radiative heat transfer.

  12. Simulation of an electrostatic soot-filter with continuous electrochemical conversion during the stages of development

    International Nuclear Information System (INIS)

    Muri, M.

    1996-04-01

    The dissertation describes the simulation of an electrostatic Diesel-Soot-Converter during its stages of development. This simulation is not only necessary for the interpretation of the experimental results, it also shows results for assumptions that cannot be received experimentally. The Diesel-Soot-Converter consists of a charging electrode, which charges the particles by a high-voltage and a ceramic monolith, where the particles are precipitated in the open channels because of an electric field created also by a high-voltage. Afterwards the particles are burned by a plasma. The filter-function of the Diesel-Soot-Converter was formulated and the efficiency for a vehicle was calculated. In the first part of the calculation the mass flow of a BMW 318tds and a BMW 325tds was determined for an US-FTP75-testcycle and for fuel load. In the second part the efficiency of different Diesel-Soot-Converter-types was calculated for the US-FTP75-testcycle and for full load. The use of the program with other testcycles is possible. The results of the calculations show the best configuration of the Diesel-Soot-Converter for the corresponding vehicle. Therefore with the help of this program time and money for the production of the ceramic can be saved. (author)

  13. Determination of polycyclic aromatic hydrocarbons in kerosene and bio-kerosene soot.

    Science.gov (United States)

    Andrade-Eiroa, Auréa; Leroy, Valérie; Dagaut, Philippe; Bedjanian, Yuri

    2010-03-01

    Here we report a new, efficient and reliable analytical methodology for sensitive and selective quantification of Polycyclic Aromatic Hydrocarbons (PAHs) in soot samples. The methodology developed is based on ultrasonic extraction of the soot-bound PAHs into small volumes of acetonitrile, purification of the extracts through C(18) Solid Phase Extraction (SPE) cartridges and analysis by Reverse Phase Liquid Chromatography (RPLC) with UV and fluorimetric detection. For the first time, we report the convenience of adapting the SPE procedure to the nature of the soot samples. As a matter of fact, extracts containing high percentage of unpolar material are recommended to be cleaned with acetone, whereas extracts poor in unpolar compounds can be efficiently cleaned with methanol. The method was satisfactorily applied to kerosene and bio-kerosene soot from atmospheric open diffusion flames (pool fires) and premixed flames achieving Quantification and Detection limits in the range ng mg(-1) soot and recoveries about 90% for most of the PAHs studied. Copyright (c) 2010 Elsevier Ltd. All rights reserved.

  14. Determination of the hydraulic residence time of trickling filters using radiotracer experiments

    International Nuclear Information System (INIS)

    Debien, Bruno R.; Ferreira, Ladislau M.; Barreto, Alberto A.; Pinto, Amenonia M.F.

    2013-01-01

    Trickling filters (TF) are bioreactors fulfilled with inert materials working as support for biofilm development, and have been used in a large scale in wastewater treatment for organic matter, ammonia nitrogen and nitrate removal. TF's can be widely used in Brazil, especially because of its simplicity and operational low cost. The efficiency of pollutants removal processes depends on the water flow dynamics inside the reactor. For this reason, in the present work the mean residence time of two TF's containing different support materials were determined by means of tracer testes. The radioisotope 82Br - a gamma radiation emitter, produced from soluble potassium bromide irradiated in the TRIGA reactor at the Centre for the Development of Nuclear Energy (CDTN) - was used as a pseudo-conservative tracer for the comparative study of aqueous phase flow dynamics in both TF's. Mean residence time for the first TF (containing a single support material) was 0,3 hours, much smaller than the value obtained for the second TF (containing two alternated support materials), around 2 hours. These results were already expected, once the alternated material is denser than the single one, and are very important for numerical modeling studies aiming to determine the kinetic constant for removal of the pollutants cited above. (author)

  15. A non-discrete method for computation of residence time in fluid mechanics simulations.

    Science.gov (United States)

    Esmaily-Moghadam, Mahdi; Hsia, Tain-Yen; Marsden, Alison L

    2013-11-01

    Cardiovascular simulations provide a promising means to predict risk of thrombosis in grafts, devices, and surgical anatomies in adult and pediatric patients. Although the pathways for platelet activation and clot formation are not yet fully understood, recent findings suggest that thrombosis risk is increased in regions of flow recirculation and high residence time (RT). Current approaches for calculating RT are typically based on releasing a finite number of Lagrangian particles into the flow field and calculating RT by tracking their positions. However, special care must be taken to achieve temporal and spatial convergence, often requiring repeated simulations. In this work, we introduce a non-discrete method in which RT is calculated in an Eulerian framework using the advection-diffusion equation. We first present the formulation for calculating residence time in a given region of interest using two alternate definitions. The physical significance and sensitivity of the two measures of RT are discussed and their mathematical relation is established. An extension to a point-wise value is also presented. The methods presented here are then applied in a 2D cavity and two representative clinical scenarios, involving shunt placement for single ventricle heart defects and Kawasaki disease. In the second case study, we explored the relationship between RT and wall shear stress, a parameter of particular importance in cardiovascular disease.

  16. Determination of flow patterns in industrial gold leaching tank by radiotracer residence time distribution measurement

    International Nuclear Information System (INIS)

    Stegowski, Z.; Furman, L.; Dagadu, Ch.P.K.; Akaho, E.H.K.; Danso, K.A.; Mumuni, I.I.; Adu, P.S; Amoah, Ch.

    2010-01-01

    The carbon-in-leach (CIL) process is one the most efficient methods of gold recovery from gold bearing ores. The efficiency of the leaching process greatly depends on the flow structure created by mechanical agitation (in some cases air agitation) in the leaching tanks. Residence time distribution (RTD) measurement was conducted in the CIL section of a gold processing plant in order to determine the flow structure in the first tank using the 131 I radioactive tracer. The shape of the experimental data revealed that the flow behaviour in the tank was close to an ideal mixer. Modelling of the experimental data, however, revealed that the tank was not behaving as a single perfect mixer, but consisted of two mixing zones. The flow structure in the tank was best described by the '' perfect mixers with exchange '' model consisting of two mixing zones. The model allowed the determination of flow parameters including the mean residence time, flow rate and volumes of the mixing zones. (authors)

  17. Tritium activity concentrations and residence times of groundwater collected in Rokkasho, Japan.

    Science.gov (United States)

    Hasegawa, Hidenao; Ueda, Shinji; Akata, Naofumi; Kakiuchi, Hideki; Hisamatsu, Shun'ichi

    2015-11-01

    Tritium ((3)H) concentrations were measured in groundwater samples from four surface wells (4-10 m deep), four shallow wells (24-26.5 m deep) and a 150-m-deep well in the Futamata River catchment area, which is adjacent to the large-scale commercial spent nuclear fuel reprocessing plant in Rokkasho, Japan. The (3)H concentrations in most of the surface- and shallow-well samples (<0.03-0.57 Bq l(-1)) were similar to those in precipitation (annual mean: 0.31-0.79 Bq l(-1)), suggesting that the residence time of the water in those wells was 0-15 y. The (3)H concentrations in the samples from a 26-m-deep well and the 150-m-deep well were lower than those in the other wells, indicating that groundwater with a long residence time exists in deep aquifers and the estuary area of the catchment. It is not clear whether (3)H released during test operation of the plant with actual spent nuclear fuel affected the (3)H concentrations observed in this study. © The Author 2015. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

  18. Determination of the hydraulic residence time of trickling filters using radiotracer experiments

    Energy Technology Data Exchange (ETDEWEB)

    Debien, Bruno R.; Ferreira, Ladislau M.; Barreto, Alberto A.; Pinto, Amenonia M.F., E-mail: brunordebien@gmail.com [Universidade Federal de Minas Gerais (UFMG), Minas Gerais, MG (Brazil). Dept. de Geografia. Lab. de Geomorfologia; Moreira, Rubens M., E-mail: aab@cdtn.br, E-mail: amfp@cdtn.br, E-mail: rubens@cdtn.br [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil)

    2013-07-01

    Trickling filters (TF) are bioreactors fulfilled with inert materials working as support for biofilm development, and have been used in a large scale in wastewater treatment for organic matter, ammonia nitrogen and nitrate removal. TF's can be widely used in Brazil, especially because of its simplicity and operational low cost. The efficiency of pollutants removal processes depends on the water flow dynamics inside the reactor. For this reason, in the present work the mean residence time of two TF's containing different support materials were determined by means of tracer testes. The radioisotope 82Br - a gamma radiation emitter, produced from soluble potassium bromide irradiated in the TRIGA reactor at the Centre for the Development of Nuclear Energy (CDTN) - was used as a pseudo-conservative tracer for the comparative study of aqueous phase flow dynamics in both TF's. Mean residence time for the first TF (containing a single support material) was 0,3 hours, much smaller than the value obtained for the second TF (containing two alternated support materials), around 2 hours. These results were already expected, once the alternated material is denser than the single one, and are very important for numerical modeling studies aiming to determine the kinetic constant for removal of the pollutants cited above. (author)

  19. Chemotaxis Increases the Residence Time Distribution of Bacteria in Granular Media Containing Distributed Contaminant Sources

    Science.gov (United States)

    Adadevoh, J.; Triolo, S.; Ramsburg, C. A.; Ford, R.

    2015-12-01

    The use of chemotactic bacteria in bioremediation has the potential to increase access to, and biotransformation of, contaminant mass within the subsurface environment. This laboratory-scale study aimed to understand and quantify the influence of chemotaxis on residence times of pollutant-degrading bacteria within homogeneous treatment zones. Focus was placed on a continuous flow sand-packed column system in which a uniform distribution of naphthalene crystals created distributed sources of dissolved phase contaminant. A 10 mL pulse of Pseudomonas putida G7, which is chemotactic to naphthalene, and Pseudomonas putida G7 Y1, a non-chemotactic mutant strain, were simultaneously introduced into the sand-packed column at equal concentrations. Breakthrough curves obtained for the bacteria from column experiments conducted with and without naphthalene were used to quantify the effect of chemotaxis on transport parameters. In the presence of the chemoattractant, longitudinal dispersivity of PpG7 increased by a factor of 3 and percent recovery decreased from 21% to 12%. The results imply that pore-scale chemotaxis responses are evident at an interstitial fluid velocity of 1.7 m/d, which is within the range of typical groundwater flow. Within the context of bioremediation, chemotaxis may work to enhance bacterial residence times in zones of contamination thereby improving treatment.

  20. Residence times and nitrate transport in ground water discharging to streams in the Chesapeake Bay Watershed

    Science.gov (United States)

    Lindsey, Bruce D.; Phillips, Scott; Donnelly, Colleen A.; Speiran, Gary K.; Plummer, Niel; Bohlke, John Karl; Focazio, Michael J.; Burton, William C.; Busenberg, Eurybiades

    2003-01-01

    One of the major water-quality problems in the Chesapeake Bay is an overabundance of nutrients from the streams and rivers that discharge to the Bay. Some of these nutrients are from nonpoint sources such as atmospheric deposition, agricultural manure and fertilizer, and septic systems. The effects of efforts to control nonpoint sources, however, can be difficult to quantify because of the lag time between changes at the land surface and the response in the base-flow (ground water) component of streams. To help resource managers understand the lag time between implementation of management practices and subsequent response in the nutrient concentrations in the base-flow component of streamflow, a study of ground-water discharge, residence time, and nitrate transport in springs throughout the Chesapeake Bay Watershed and in four smaller watersheds in selected hydrogeomorphic regions (HGMRs) was conducted. The four watersheds were in the Coastal Plain Uplands, Piedmont crystalline, Valley and Ridge carbonate, and Valley and Ridge siliciclastic HGMRs.A study of springs to estimate an apparent age of the ground water was based on analyses for concentrations of chlorofluorocarbons in water samples collected from 48 springs in the Chesapeake Bay Watershed. Results of the analysis indicate that median age for all the samples was 10 years, with the 25th percentile having an age of 7 years and the 75th percentile having an age of 13 years. Although the number of samples collected in each HGMR was limited, there did not appear to be distinct differences in the ages between the HGMRs. The ranges were similar between the major HGMRs above the Fall Line (modern to about 50 years), with only two HGMRs of small geographic extent (Piedmont carbonate and Mesozoic Lowland) having ranges of modern to about 10 years. The median values of all the HGMRs ranged from 7 to 11 years. Not enough samples were collected in the Coastal Plain for comparison. Spring samples showed slightly younger

  1. Cloud droplet activity changes of soot aerosol upon smog chamber ageing

    Science.gov (United States)

    Wittbom, C.; Eriksson, A. C.; Rissler, J.; Carlsson, J. E.; Roldin, P.; Nordin, E. Z.; Nilsson, P. T.; Swietlicki, E.; Pagels, J. H.; Svenningsson, B.

    2014-09-01

    Particles containing soot, or black carbon, are generally considered to contribute to global warming. However, large uncertainties remain in the net climate forcing resulting from anthropogenic emissions of black carbon (BC), to a large extent due to the fact that BC is co-emitted with gases and primary particles, both organic and inorganic, and subject to atmospheric ageing processes. In this study, diesel exhaust particles and particles from a flame soot generator spiked with light aromatic secondary organic aerosol (SOA) precursors were processed by UV radiation in a 6 m3 Teflon chamber in the presence of NOx. The time-dependent changes of the soot nanoparticle properties were characterised using a Cloud Condensation Nuclei Counter, an Aerosol Particle Mass Analyzer and a Soot Particle Aerosol Mass Spectrometer. The results show that freshly emitted soot particles do not activate into cloud droplets at supersaturations ≤2%, i.e. the BC core coated with primary organic aerosol (POA) from the exhaust is limited in hygroscopicity. Before the onset of UV radiation it is unlikely that any substantial SOA formation is taking place. An immediate change in cloud-activation properties occurs at the onset of UV exposure. This change in hygroscopicity is likely attributed to SOA formed from intermediate volatility organic compounds (IVOCs) in the diesel engine exhaust. The change of cloud condensation nuclei (CCN) properties at the onset of UV radiation implies that the lifetime of soot particles in the atmosphere is affected by the access to sunlight, which differs between latitudes. The ageing of soot particles progressively enhances their ability to act as cloud condensation nuclei, due to changes in: (I) organic fraction of the particle, (II) chemical properties of this fraction (e.g. primary or secondary organic aerosol), (III) particle size, and (IV) particle morphology. Applying κ-Köhler theory, using a κSOA value of 0.13 (derived from independent input

  2. The Removal of Aquacultural Wastes by Foams Separator from Sea Water II. The Effect of Hydraulic Residence Time

    Energy Technology Data Exchange (ETDEWEB)

    Suh, Kuen Hack; Kim, Byong Jin; Kim, Yong Ha; Yi, Gyeongbeom; Lim, Jung Heok [Department of Chemical Engineering, Pukyong National University, Pusan (Korea); Kim, Sung Koo [Department of Biotechnology and Bioengineering, Pukyong National University, Pusan (Korea)

    2001-04-01

    Experimental investigations on the effect of the hydraulic residence time(HRT) for the removal of aquacultural waste, such as protein, total suspended solids(TSS), chemical oxygen demand(COD), turbidity and total ammonia nitrogen(TAN) from sea water were carried out by using foam separator. The foam separator as an aerator was also evaluated for increasing dissolved oxygen concentration. The increase in hydraulic residence time increased the removal efficiencies of aquacultural waste. Optimum hydraulic residence time was 0.48 min and the highest protein removal rate was 10.25 g/m{sup 3} min. The changes of removal rates and efficiencies of TSS, COD and turbidity were similar to proteins. The hydraulic residence time for highest overall oxygen mass transfer coefficient was the optimum condition for the highest protein removal rate. 23 refs., 15 figs., 1 tab.

  3. The significance of oxygen as oxides and hydroxides in controlling the abundance and residence times of elements in seawater

    Digital Repository Service at National Institute of Oceanography (India)

    DileepKumar, M.

    A model is presented which signifies the role of oxygen (as oxides and hydroxides) in controlling the composition of seawater. respective concentration and residence times for the unknown elements can be estimated. Geometric and statistical indices...

  4. Prevalence and Cost of Full-Time Research Fellowships During General Surgery Residency – A National Survey

    Science.gov (United States)

    Robertson, Charles M.; Klingensmith, Mary E.; Coopersmith, Craig M.

    2009-01-01

    Structured Abstract Objective To quantify the prevalence, outcomes, and cost of surgical resident research. Summary Background Data General surgery is unique among graduate medical education programs because a large percentage of residents interrupt their clinical training to spend 1-3 years performing full-time research. No comprehensive data exists on the scope of this practice. Methods Survey sent to all 239 program directors of general surgery residencies participating in the National Resident Matching Program. Results Response rate was 200/239 (84%). A total of 381 out of 1052 trainees (36%) interrupt residency to pursue full-time research. The mean research fellowship length is 1.7 years, with 72% of trainees performing basic science research. A significant association was found between fellowship length and post-residency activity, with a 14.7% increase in clinical fellowship training and a 15.2% decrease in private practice positions for each year of full-time research (p<0.0001). Program directors at 31% of programs reported increased clinical duties for research fellows as a result of ACGME work hour regulations for clinical residents, while a further 10% of programs are currently considering such changes. It costs $41.5 million to pay the 634 trainees who perform research fellowships each year, the majority of which is paid for by departmental funds (40%) and institutional training grants (24%). Conclusions Interrupting residency to perform a research fellowship is a common and costly practice among general surgery residents. While performing a research fellowship is associated with clinical fellowship training after residency, it is unclear to what extent this practice leads to the development of surgical investigators after post-graduate training. PMID:19106692

  5. The effect of residence time on the dynamics of a condensating aerosol in a Hiemenz-type stagnation flow

    Science.gov (United States)

    Alshaarawi, Amjad; Zhou, Kun; Scribano, Gianfranco; Attili, Antonio; Bisetti, Fabrizio; Clean Combustion Research Center Team

    2013-11-01

    The effect of residence time on the formation and growth of a condensating aerosol is simulated in a Hiemenz-type stagnation flow setup, for which a unique and well-defined time scale characterizes the velocity field. In this configuration, a hot stream saturated with dibutyle phthalate (DBP) vapor mixes with a cold dry stream. A mixing layer forms at the stagnation plane triggering supersaturation and droplets are generated by homogeneous nucleation. Aerosol dynamics are simulated using the Quadrature Method of Moments (QMOM). Two regimes related to the flow residence time are observed, i.e., a nucleation regime and a condensation regime. The nucleation regime, at short residence times, is characterized by the consumption of DBP vapor into droplets having a negligible effect on the vapor phase. In this regime, both the number density and volume fraction of droplets increase with residence time. In the condensation regime, at long residence times, vapor condensation consumes the vapor phase considerably. For longer residence times, more vapor is consumed, resulting in lower number densities due to the lower nucleation rates, whereas the volume fraction saturates.

  6. Chinese Soot on a Vietnamese Soup

    Science.gov (United States)

    Mari, X.

    2015-12-01

    Black Carbon (BC) is an aerosol emitted as soot during biomass burning and fossil fuels combustion together with other carbonaceous aerosols such as organic carbon (OC) and polyaromatic hydrocarbons (PAHs). While the impacts of BC on health and climate have been studied for many years, studies about its deposition and impact on marine ecosystems are scares. This is rather surprising considering that a large fraction of atmospheric BC deposits on the surface of the ocean via dry or wet deposition. On a global scale, deposition on the ocean is about 45 Tg C per year, with higher fluxes in the northern hemisphere and in inter-tropical regions, following the occurrence of the hot-spots of concentration. In the present study conducted on shore, in Haiphong and Halong cities, North Vietnam, we measured the seasonal variations of atmospheric BC, OC and PAHs during a complete annual cycle. The presentation will discuss the atmospheric results in terms of seasonal variability and sources. Inputs to the marine system are higher during the dry season, concomitantly with the arrival of air masses enriched in BC coming from the North. However, the carbon fingerprint can significantly differ at shorter time periods depending on the air mass pathway and speed. Our work leads to the characterization and the determination of the relative contribution of more specific sources like local traffic, which includes tourism and fishing boats, coal dust emitted from the nearby mine, and long-range transported aerosols. This variable input of carbonaceous aerosols might have consequences for the cycling and the repartition of carbon and nutrients in the marine ecosystem of Halong Bay.

  7. Thermal fragmentation and deactivation of combustion-generated soot particles

    KAUST Repository

    Raj, Abhijeet

    2014-09-01

    The effect of thermal treatment on diesel soot and on a commercial soot in an inert environment under isothermal conditions at intermediate temperatures (400-900°C) is studied. Two important phenomena are observed in both the soot samples: soot fragmentation leading to its mass loss, and loss of soot reactivity towards O2. Several experimental techniques such as high resolution transmission electron microscopy, electron energy loss spectroscopy, thermo-gravimetric analysis with mass spectrometry, elemental analysis, Fourier transform infrared spectroscopy and X-ray diffraction have been used to identify the changes in structures, functional groups such as oxygenates and aliphatics, σ and π bonding, O/C and H/C ratios, and crystallite parameters of soot particles, introduced by heat. A decrease in the size of primary particles and an increase in the average polycyclic aromatic hydrocarbon (PAH) size was observed in soots after thermal treatment. The activation energies of soot oxidation for thermally treated soot samples were found to be higher than those for the untreated ones at most conversion levels. The cyclic or acyclic aliphatics with sp3 hybridization were present in significant amounts in all the soot samples, but their concentration decreased with thermal treatment. Interestingly, the H/C and the O/C ratios of soot particles increased after thermal treatment, and thus, they do not support the decrease in soot reactivity. The increase in the concentration of oxygenates on soot surface indicate that their desorption from soot surface in the form of CO, CO2 and other oxygenated compounds may not be significant at the temperatures (400-900°C) studied in this work. © 2014 The Combustion Institute.

  8. Smog chamber study on aging of combustion soot in isoprene/SO2/NOx system: Changes of mass, size, effective density, morphology and mixing state

    Science.gov (United States)

    Li, Kangwei; Chen, Linghong; Han, Ke; Lv, Biao; Bao, Kaiji; Wu, Xuecheng; Gao, Xiang; Cen, Kefa

    2017-02-01

    Atmospheric soot aging process is always accompanied by secondary particle formation, which is a comprehensive environmental issue that deserves great attention. On one hand, aging of primary soot could change its own physicochemical properties; on the other hand, complex air pollution caused by pollutant emission from various sources (e.g., vehicle exhausts, coal-fired flue gases and biogenic VOCs emission) may contribute to secondary particle formation onto primary particle surface. In this study, aging of combustion soot in isoprene/SO2/NOx system was investigated under controlled laboratory conditions in several smog chamber experiments. During the evolution of soot, several physical properties such as mass, size, effective density, morphology and mixing state were determined simultaneously by an integrated aerosol analytical system of Scanning Mobility Particle Sizer (SMPS), Differential Mobility Analyzer-Aerosol Particle Mass Analyzer-Condensation Particle Counter (DMA-APM-CPC) and Transmission Electron Microscopy coupled with Energy-dispersive X-ray Spectrometry (TEM/EDX) techniques. Here, based on the experimental results of soot aging under different gas-phase composition and relative humidity (RH), we firstly proposed possible aging pathways of soot in isoprene/SO2/NOx system. A synergetic effect was speculated to exist between SO2 and isoprene on soot aging process, which led to more secondary particle formation. At the same time, TEM/EDX analysis showed that a competitive mechanism between H2SO4(g) and isoprene oxidation vapor may exist: H2SO4(g) firstly condensed onto fresh soot, then an acceleration of isoprene oxidation products formed onto H2SO4 pre-coated soot. In isoprene/SO2/NOx system, high RH conditions could contribute to soot aging and new particle formation. The changes of effective density and dynamic shape factor of soot also indicated that high RH conditions could accelerate soot aging process, and led chain-like soot into more spherical

  9. Temporal evolution and variability of dissolved inorganic nitrogen in beach pore water revealed using radon residence times.

    Science.gov (United States)

    Goodridge, Blair M; Melack, John M

    2014-12-16

    We coupled measurements of beach pore water residence time, determined using the radioisotopic tracer (222)Rn, with dissolved carbon and nitrogen chemistry to identify the temporal evolution and variability of dissolved inorganic nitrogen (DIN) concentrations in beach pore water along the Santa Barbara, California coastline. Pore water dissolved organic carbon (DOC) and total dissolved nitrogen (TDN) ratios (DOC:TDN) were negative exponentially correlated with residence time. Mean pore water residence times were positively correlated with tidal amplitudes, and ranged from 4.4 to 6.4 days. We used this range in mean residence times to model radon residence time distributions (RTDs), and integrated them with modeled DIN vs residence time relationships (DIN-temporal evolution, or DIN-te curves) to derive volume-weighted mean (VWM) DIN concentrations. We observed 1.2-fold and 5.2-fold differences (20% and 420% increases) in VWM DIN concentrations over the range in modeled RTDs and DIN-te curves, respectively, and a maximum 6.4-fold difference (540% increase) in VWM DIN concentrations for an interactive shift in the RTD and the DIN-te curve. Our study suggests that accounting for temporal variability in the RTD and DIN concentration of pore water is necessary to obtain more accurate estimates of DIN delivery to coastal oceans.

  10. Variability in benthic exchange rate, depth, and residence time beneath a shallow coastal estuary

    Science.gov (United States)

    Russoniello, C. J.; Michael, H. A.; Heiss, J.

    2017-12-01

    Hydrodynamically-driven exchange of water between the water column and shallow seabed aquifer, benthic exchange, is a significant and dynamic component of coastal and estuarine fluid budgets, but wave-induced benthic exchange has not been measured in the field. Mixing between surface water and groundwater solutes promotes ecologically important chemical reactions, so quantifying benthic exchange rates, depths, and residence times, constrains estimates of coastal chemical cycling. In this study, we present the first field-based direct measurements of wave-induced exchange and compare it to exchange induced by the other primary drivers of exchange - tides, and currents. We deployed instruments in a shallow estuary to measure benthic exchange and temporal variability over an 11-day period. Differential pressure sensors recorded pressure gradients across the seabed, and up-and down-looking ADCPs recorded currents and pressures from which wave parameters, surface-water currents, and water depth were determined. Wave-induced exchange was calculated directly from 1) differential pressure measurements, and indirectly with an analytical solution based on wave parameters from 2) ADCP and 3) weather station data. Groundwater flow models were used to assess the effects of aquifer properties on benthic exchange depth and residence time. Benthic exchange driven by tidal pumping or current-bedform interaction was calculated from tidal stage variation and from ADCP-measured currents at the bed, respectively. Waves were the primary benthic exchange driver (average = 20.0 cm/d, maximum = 92.3 cm/d) during the measurement period. Benthic exchange due to tides (average = 3.7 cm/d) and current-bedform interaction (average = 6.5x10-2 cm/d) was much lower. Wave-induced exchange calculated from pressure measurements and ADCP-measured wave parameters matched well, but wind-based rates underestimated wave energy and exchange. Groundwater models showed that residence time and depth increased

  11. Trait differences between naturalized and invasive plant species independent of residence time and phylogeny.

    Science.gov (United States)

    Gallagher, R V; Randall, R P; Leishman, M R

    2015-04-01

    The ability to predict which alien plants will transition from naturalized to invasive prior to their introduction to novel regions is a key goal for conservation and has the potential to increase the efficacy of weed risk assessment (WRA). However, multiple factors contribute to plant invasion success (e.g., functional traits, range characteristics, residence time, phylogeny), and they all must be taken into account simultaneously in order to identify meaningful correlates of invasion success. We compiled 146 pairs of phylogenetically paired (congeneric) naturalized and invasive plant species in Australia with similar minimum residence times (i.e., time since introduction in years). These pairs were used to test for differences in 5 functional traits (flowering duration, leaf size, maximum height, specific leaf area [SLA], seed mass) and 3 characteristics of species' native ranges (biome occupancy, mean annual temperature, and rainfall breadth) between naturalized and invasive species. Invasive species, on average, had larger SLA, longer flowering periods, and were taller than their congeneric naturalized relatives. Invaders also exhibited greater tolerance for different environmental conditions in the native range, where they occupied more biomes and a wider breadth of rainfall and temperature conditions than naturalized congeners. However, neither seed mass nor leaf size differed between pairs of naturalized and invasive species. A key finding was the role of SLA in distinguishing between naturalized and invasive pairs. Species with high SLA values were typically associated with faster growth rates, more rapid turnover of leaf material, and shorter lifespans than those species with low SLA. This suite of characteristics may contribute to the ability of a species to transition from naturalized to invasive across a wide range of environmental contexts and disturbance regimes. Our findings will help in the refinement of WRA protocols, and we advocate the inclusion

  12. Calculation of residence times and radiation doses using the standard PC software Excel

    International Nuclear Information System (INIS)

    Herzog, H.; Zilken, H.; Niederbremer, A.; Friedrich, W.; Mueller-Gaertner, H.W.

    1997-01-01

    We developed a program which aims to facilitate the calculation of radiation doses to single organs and the whole body. IMEDOSE uses Excel to include calculations, graphical displays, and interactions with the user in a single general-purpose PC software tool. To start the procedure the input data are copied into a spreadsheet. They must represent percentage uptake values of several organs derived from measurements in animals or humans. To extrapolate these data up to seven half-lives of the radionuclide, fitting to one or two exponentional functions is included and can be checked by the user. By means of the approximate time-activity information the cumulated activity or residence times are calculated. Finally these data are combined with the absorbed fraction doses (S-values) given by MIRD pamphlet No. 11 to yield radiation doses, the effective dose equivalent and the effective dose. These results are presented in a final table. Interactions are realized with push-buttons and drop-down menus. Calculations use the Visual Basic tool of Excel. In order to test our program, biodistribution data of fluorine-18 fluorodeoxyglucose were taken from the literature (Meija et al., J Nucl Med 1991; 32:699-706). For a 70-kg adult the resulting radiation doses of all target organs listed in MIRD 11 were different from the ICRP 53 values by 1%±18% on the average. When the residence times were introduced into MIRDOSE3 (Stabin, J Nucl Med 1996; 37:538-546) the mean difference between our results and those of MIRDOSE3 was -3%±6%. Both outcomes indicate the validity of the present approach. (orig.)

  13. Calculation of residence times and radiation doses using the standard PC software Excel.

    Science.gov (United States)

    Herzog, H; Zilken, H; Niederbremer, A; Friedrich, W; Müller-Gärtner, H W

    1997-12-01

    We developed a program which aims to facilitate the calculation of radiation doses to single organs and the whole body. IMEDOSE uses Excel to include calculations, graphical displays, and interactions with the user in a single general-purpose PC software tool. To start the procedure the input data are copied into a spreadsheet. They must represent percentage uptake values of several organs derived from measurements in animals or humans. To extrapolate these data up to seven half-lives of the radionuclide, fitting to one or two exponentional functions is included and can be checked by the user. By means of the approximate time-activity information the cumulated activity or residence times are calculated. Finally these data are combined with the absorbed fraction doses (S-values) given by MIRD pamphlet No. 11 to yield radiation doses, the effective dose equivalent and the effective dose. These results are presented in a final table. Interactions are realized with push-buttons and drop-down menus. Calculations use the Visual Basic tool of Excel. In order to test our program, biodistribution data of fluorine-18 fluorodeoxyglucose were taken from the literature (Meija et al., J Nucl Med 1991; 32:699-706). For a 70-kg adult the resulting radiation doses of all target organs listed in MIRD 11 were different from the ICRP 53 values by 1%+/-18% on the average. When the residence times were introduced into MIRDOSE3 (Stabin, J Nucl Med 1996; 37:538-546) the mean difference between our results and those of MIRDOSE3 was -3%+/-6%. Both outcomes indicate the validity of the present approach.

  14. Calculation of residence times and radiation doses using the standard PC software Excel

    Energy Technology Data Exchange (ETDEWEB)

    Herzog, H.; Zilken, H.; Niederbremer, A.; Friedrich, W. [Institute of Medicine, Research Center Juelich, Juelich (Germany); Mueller-Gaertner, H.W. [Institute of Medicine, Research Center Juelich, Juelich (Germany)]|[Department of Nuclear Medicine, Heinrich-Heine University Hospital Duesseldorf (Germany)

    1997-12-01

    We developed a program which aims to facilitate the calculation of radiation doses to single organs and the whole body. IMEDOSE uses Excel to include calculations, graphical displays, and interactions with the user in a single general-purpose PC software tool. To start the procedure the input data are copied into a spreadsheet. They must represent percentage uptake values of several organs derived from measurements in animals or humans. To extrapolate these data up to seven half-lives of the radionuclide, fitting to one or two exponentional functions is included and can be checked by the user. By means of the approximate time-activity information the cumulated activity or residence times are calculated. Finally these data are combined with the absorbed fraction doses (S-values) given by MIRD pamphlet No. 11 to yield radiation doses, the effective dose equivalent and the effective dose. These results are presented in a final table. Interactions are realized with push-buttons and drop-down menus. Calculations use the Visual Basic tool of Excel. In order to test our program, biodistribution data of fluorine-18 fluorodeoxyglucose were taken from the literature (Meija et al., J Nucl Med 1991; 32:699-706). For a 70-kg adult the resulting radiation doses of all target organs listed in MIRD 11 were different from the ICRP 53 values by 1%{+-}18% on the average. When the residence times were introduced into MIRDOSE3 (Stabin, J Nucl Med 1996; 37:538-546) the mean difference between our results and those of MIRDOSE3 was -3%{+-}6%. Both outcomes indicate the validity of the present approach. (orig.) With 5 figs., 2 tabs., 18 refs.

  15. Residence time distribution measurements in a pilot-scale poison tank using radiotracer technique.

    Science.gov (United States)

    Pant, H J; Goswami, Sunil; Samantray, J S; Sharma, V K; Maheshwari, N K

    2015-09-01

    Various types of systems are used to control the reactivity and shutting down of a nuclear reactor during emergency and routine shutdown operations. Injection of boron solution (borated water) into the core of a reactor is one of the commonly used methods during emergency operation. A pilot-scale poison tank was designed and fabricated to simulate injection of boron poison into the core of a reactor along with coolant water. In order to design a full-scale poison tank, it was desired to characterize flow of liquid from the tank. Residence time distribution (RTD) measurement and analysis was adopted to characterize the flow dynamics. Radiotracer technique was applied to measure RTD of aqueous phase in the tank using Bromine-82 as a radiotracer. RTD measurements were carried out with two different modes of operation of the tank and at different flow rates. In Mode-1, the radiotracer was instantaneously injected at the inlet and monitored at the outlet, whereas in Mode-2, the tank was filled with radiotracer and its concentration was measured at the outlet. From the measured RTD curves, mean residence times (MRTs), dead volume and fraction of liquid pumped in with time were determined. The treated RTD curves were modeled using suitable mathematical models. An axial dispersion model with high degree of backmixing was found suitable to describe flow when operated in Mode-1, whereas a tanks-in-series model with backmixing was found suitable to describe flow of the poison in the tank when operated in Mode-2. The results were utilized to scale-up and design a full-scale poison tank for a nuclear reactor. Copyright © 2015 Elsevier Ltd. All rights reserved.

  16. Simulation and analysis of the soot particle size distribution in a turbulent nonpremixed flame

    KAUST Repository

    Lucchesi, Marco

    2017-02-05

    A modeling framework based on Direct Simulation Monte Carlo (DSMC) is employed to simulate the evolution of the soot particle size distribution in turbulent sooting flames. The stochastic reactor describes the evolution of soot in fluid parcels following Lagrangian trajectories in a turbulent flow field. The trajectories are sampled from a Direct Numerical Simulation (DNS) of a n-heptane turbulent nonpremixed flame. The DSMC method is validated against experimentally measured size distributions in laminar premixed flames and found to reproduce quantitatively the experimental results, including the appearance of the second mode at large aggregate sizes and the presence of a trough at mobility diameters in the range 3–8 nm. The model is then applied to the simulation of soot formation and growth in simplified configurations featuring a constant concentration of soot precursors and the evolution of the size distribution in time is found to depend on the intensity of the nucleation rate. Higher nucleation rates lead to a higher peak in number density and to the size distribution attaining its second mode sooner. The ensemble-averaged PSDF in the turbulent flame is computed from individual samples of the PSDF from large sets of Lagrangian trajectories. This statistical measure is equivalent to time-averaged, scanning mobility particle size (SMPS) measurements in turbulent flames. Although individual trajectories display strong bimodality as in laminar flames, the ensemble-average PSDF possesses only one mode and a long, broad tail, which implies significant polydispersity induced by turbulence. Our results agree very well with SMPS measurements available in the literature. Conditioning on key features of the trajectory, such as mixture fraction or radial locations does not reduce the scatter in the size distributions and the ensemble-averaged PSDF remains broad. The results highlight and explain the important role of turbulence in broadening the size distribution of

  17. Catalytic oxidation of soot over alkaline niobates

    International Nuclear Information System (INIS)

    Pecchi, G.; Cabrera, B.; Buljan, A.; Delgado, E.J.; Gordon, A.L.; Jimenez, R.

    2013-01-01

    Highlights: ► No previous reported studies about alkaline niobates as catalysts for soot oxidation. ► NaNbO 3 and KNbO 3 perovskite-type oxides show lower activation energy than other lanthanoid perovskite-type oxides. ► The alkaline niobate does not show deactivation by metal loss. - Abstract: The lack of studies in the current literature about the assessment of alkaline niobates as catalysts for soot oxidation has motivated this research. In this study, the synthesis, characterization and assessment of alkaline metal niobates as catalysts for soot combustion are reported. The solids MNbO 3 (M = Li, Na, K, Rb) are synthesized by a citrate method, calcined at 450 °C, 550 °C, 650 °C, 750 °C, and characterized by AAS, N 2 adsorption, XRD, O 2 -TPD, FTIR and SEM. All the alkaline niobates show catalytic activity for soot combustion, and the activity depends basically on the nature of the alkaline metal and the calcination temperature. The highest catalytic activity, expressed as the temperature at which combustion of carbon black occurs at the maximum rate, is shown by KNbO 3 calcined at 650 °C. At this calcination temperature, the catalytic activity follows an order dependent on the atomic number, namely: KNbO 3 > NaNbO 3 > LiNbO 3 . The RbNbO 3 solid do not follow this trend presumably due to the perovskite structure was not reached. The highest catalytic activity shown by of KNbO 3 , despite the lower apparent activation energy of NaNbO 3 , stress the importance of the metal nature and suggests the hypothesis that K + ions are the active sites for soot combustion. It must be pointed out that alkaline niobate subjected to consecutive soot combustion cycles does not show deactivation by metal loss, due to the stabilization of the alkaline metal inside the perovskite structure.

  18. Determination of the resident time distribution (RTD) in copper concentrate drying plants using radioactive tracers

    International Nuclear Information System (INIS)

    Diaz V, Francisco J.; Duran P, Oscar U.; Hernandez A, Fernando A.

    1996-01-01

    This paper is a study on the drying process of copper concentrate, on two fluidized bed dryers at Fundicion Caletones, Division El Teniente, Codelco-Chile. The problem was investigated by experimental determination of the resident Time Distribution (RTD) for the material to be dry and by an analysis of the influence of the grain size in the drying process. The stimulus-response technique was used in the experiments, where the stimulation was a pulse of an adequate radioactive tracer injected at the dryer's input. Under these conditions, the response obtained at the dryer's outputs, i.e., the concentration variation curve as a function of time, represents directly the RTD of the system between the injection and measuring points. The tracer used was the same material to be dried, and it was irradiated with neutrons in the nuclear reactor at La Reina Nuclear Centre, thus producing a solid gamma radiation emitter tracer of identical behaviour as the material under study. The approximate activity of each sample was equivalent to 8 mCi of Cu-64 at the time of the injection and the measurement of the tracer was made on-line using NaI(Tl) gamma radiation detectors. The results obtained showed average times less than the estimated and would indicate a fast drying using minimum volume in the dryer. The drying of the fine particles was three times faster than the coarse ones. (author)

  19. Residence time, dispersal, and harvest of waterfowl using a radioactive leaching pond in southeastern Idaho

    International Nuclear Information System (INIS)

    Browers, H.W. Jr.; Flake, L.D.

    1983-01-01

    A study was initiated in the fall of 1980 to determine residence times, dispersal, and harvest of waterfowl using the Test Reactor Area (TRA) radioactive leaching pond complex on the Idaho National Engineering Laboratory (INEL) site. Attempts were made to capture and band waterfowl using the ponds during migration. Three common goldeneyes (Bucephala clangula) and six mallards (Anas platyrynchos) were captured in the fall of 1980. Three mallards were also captured in the fall of 1981. Two bands have been recovered to date. In addition, daily observations were made from August to December 1980 and from October to December 1981 and the number and species of waterfowl were recorded. As of December 15, 1981, 665 waterfowl representing 14 species had been observed. However,the total number of waterfowl observed does not represent an accurate census due to recounts of some individuals

  20. Devolatilization kinetics of woody biomass at short residence times and high heating rates and peak temperatures

    DEFF Research Database (Denmark)

    Johansen, Joakim M.; Gadsbøll, Rasmus; Thomsen, Jesper

    2016-01-01

    were conducted on a laboratory laminar entrained flow reactor (LFR) using solid fuel feed rates on the order of 10-20mgh-1. Employing a simple single step first order (SFOR) mechanism with an Arrhenius type rate expression, the best fit of the pyrolysis kinetics was found to be: A=18.9×103s-1, Ea=21305......This work combines experimental and computational fluid dynamics (CFD) results to derive global kinetics for biomass (pine wood) devolatilization during heating rates on the order of 105Ks-1, bulk flow peak temperatures between 1405 and 1667K, and particle residence times below 0.1s. Experiments......Jmol-1. The accuracy of the derived global kinetics was supported by comparing predictions to experimental results from a 15kW furnace. The work emphasizes the importance of characterizing the temperature history of the biomass particles when deriving pyrolysis kinetics. The present results indicate...

  1. Recent extensions of the residence time distribution concept: unsteady state conditions and hydrodynamic model developments

    Directory of Open Access Journals (Sweden)

    Claudel S.

    2000-01-01

    Full Text Available Two recent extensions of the residence time distribution concept are developed. The first one concerns the use of this method under transient conditions, a concept theoretically treated but rarely confirm by relevant experiments. In the present work, two experimental set-ups have been used to verify some limits of the concept. The second extension is devoted to the development of hydrodynamic models. Up to now, the hydrodynamics of the process are either determined by simple models (mixing cells in series, plug flow reactor with axial dispersion or by the complex calculation of the velocity profile obtained via the Navier-Stokes equations. An alternative is to develop a hydrodynamic model by use of a complex network of interconnected elementary reactors. Such models should be simple enough to be derived easily and sufficiently complex to give a good representation of the behavior of the process.

  2. Soot oxidation over NOx storage catalysts. Activity and deactivation

    International Nuclear Information System (INIS)

    Krishna, K.; Makkee, M.

    2006-01-01

    Soot oxidation activity and deactivation of NO x storage and reduction (NSR) catalysts containing Pt, K, and Ba supported on Al 2 O 3 , are studied under a variety of reaction conditions. K-containing catalysts decrease soot oxidation temperature with O 2 alone and the presence of Pt further enhance the activity due to synergetic effect. The active species responsible for synergism on Pt/K-Al 2 O 3 are unstable and cannot be regenerated. Soot oxidation temperature decreases by about 150 o C with NO+O 2 exhaust feed gas and under lean conditions NSR system acts as catalysed soot filter (CSF). The reactions that are mainly responsible for decreasing soot oxidation temperature are: (1) soot oxidation with NO 2 followed by NO recycles to NO 2 , and (2) soot oxidation with O 2 assisted by NO 2 . Only a part of the stored NO x that is decomposed at high temperatures under lean conditions is found to be useful for soot oxidation. NO x storage capacity of NSR catalysts decreases upon ageing under soot oxidising conditions. This will lead to a decreased soot oxidation activity on stored nitrate decomposition. Pt/K-Al 2 O 3 catalyst is more active, but least stable compared with Pt/Ba-Al 2 O 3 . (author)

  3. On the Response of Nascent Soot Nanostructure and Oxidative Reactivity to Photoflash Exposure

    Directory of Open Access Journals (Sweden)

    Wei Wang

    2017-07-01

    Full Text Available Soot particles are a kind of major pollutant from fuel combustion. To enrich the understanding of soot, this work focuses on investigating detailed influences of instantaneous external irradiation (conventional photoflash exposure on nanostructure as well as oxidation reactivity of nascent soot particles. By detailed soot characterizations flash can reduce the mass of soot and soot nanostructure can be reconstructed substantially without burning. After flash, the degree of soot crystallization increases while the soot reactive rate decreases and the activation energy increases. In addition, nanostructure and oxidative reactivity of soot in air and Ar after flash are different due to their different thermal conductivities.

  4. On-site residence time in a driven diffusive system: Violation and recovery of a mean-field description.

    Science.gov (United States)

    Messelink, J; Rens, R; Vahabi, M; MacKintosh, F C; Sharma, A

    2016-01-01

    We investigate simple one-dimensional driven diffusive systems with open boundaries. We are interested in the average on-site residence time defined as the time a particle spends on a given site before moving on to the next site. Using mean-field theory, we obtain an analytical expression for the on-site residence times. By comparing the analytic predictions with numerics, we demonstrate that the mean-field significantly underestimates the residence time due to the neglect of time correlations in the local density of particles. The temporal correlations are particularly long-lived near the average shock position, where the density changes abruptly from low to high. By using domain wall theory, we obtain highly accurate estimates of the residence time for different boundary conditions. We apply our analytical approach to residence times in a totally asymmetric exclusion process (TASEP), TASEP coupled to Langmuir kinetics (TASEP+LK), and TASEP coupled to mutually interactive LK (TASEP+MILK). The high accuracy of our predictions is verified by comparing these with detailed Monte Carlo simulations.

  5. Soot formation of lignin derived fuels in a laminar co-flow diffusion flame

    Energy Technology Data Exchange (ETDEWEB)

    Bertrand, P.A.M.

    2009-07-15

    Due to limited fossil fuels reserves and increasing CO2 and soot concentration in the atmosphere, other cleaner fuels are needed. Use of biomass waste for the production of second generation bio-fuels might lead to a reduction of CO2 emissions. Second generation bio-fuels from biomass waste do not compete with food stock markets. Although limited available per unit time, biomass waste will be produced for ever. Therefore this resource is sustainable. Research on sooting tendency of different types of fuels is needed to find low sooting fuels which decrease air pollution, thereby killing two birds with one stone. Current research investigated sooting tendencies of possible biofuels from lignin. Lignin is a biopolymer which accounts for 15-30 wt.% of woody biomass. Besides lignin, woody biomass consists of mainly cellulose and hemicellulose. Lignin is responsible for mechanical support of the plant, water conduction and protection against biodegradation. A method was searched to assign a value to a fuel which corresponds to the sooting tendency of that fuel. The method should be validated with Threshold Sooting Index (TSI) and Yield Sooting Index (YSI). The former is an aviation fuel testing method based on smoke point height while the latter is a recently developed method which measures soot concentrations using LII, both using laminar diffusion flames. In the current investigation sooting tendency was measured using line-of-sight attenuation in combination with inverse Abel transformation to determine the spatially resolved soot volume fraction. Different concentrations of test fuel (acetone, ethanol, cyclohexene, cyclohexanone, methane and toluene) mixed with base fuel (33,3 wt.% toluene and 66,7 wt.% n-heptane) were investigated. To enable rapid fuel changing a new fuel accumulator system was designed. In this system a syringe with a small amount of test fuel can easily be placed. Therefore no cleaning of the fuel accumulator is required since the syringes are

  6. Quantitative effects of rapid heating on soot-particle sizing through analysis of two-pulse LII

    KAUST Repository

    Cenker, Emre

    2017-02-27

    During the rapid laser pulse heating and consecutive cooling in laser-induced incandescence (LII), soot particles may undergo thermal annealing and sublimation processes which lead to a permanent change in its optical properties and its primary particle size, respectively. Overall, effects of these two processes on soot and LII model-based particle sizing are investigated by measuring the two-color time-resolved (2C-TiRe) LII signal decay from in-flame soot after two consecutive laser pulses at 1064-nm wavelength. Experiments are carried out on a non-premixed laminar ethylene/air flame from a Santoro burner with both low and moderate laser fluences suitable for particle sizing. The probe volume is set to a radial position close to the flame axis where the soot particles are known to be immature or less graphitic. With the first pulse, soot is pre-heated, and the LII signal after the consecutive second pulse is used for analysis. The two-color incandescence emission technique is used for the pyrometric determination of the LII-heated peak soot temperature at the second pulse. A new LII simulation tool is developed which accounts for particle heating via absorption and annealing, and cooling via sublimation, conduction, and radiation with various existing sub-models from the literature. The same approach of using two laser pulses is implemented in the simulations. Measurements indicate that thermal annealing and associated absorption enhancement becomes important at laser fluences above 0.17 J/cm2 for the immature in-flame soot. After a heating pulse at 0.33 J/cm2, the increase of the soot absorption function is calculated as 35% using the temperature measured at the second pulse and an absorption model based on the Rayleigh approximation. Present annealing model, on the other hand, predicts graphitization of soot even in the absence of laser heating at typical flame temperatures. Recorded experimental LII signal decays and LII-heated peak soot temperature

  7. Sooting Characteristics and Modeling in Counterflow Diffusion Flames

    KAUST Repository

    Wang, Yu

    2013-11-01

    Soot formation is one of the most complex phenomena in combustion science and an understanding of the underlying physico-chemical mechanisms is important. This work adopted both experimental and numerical approaches to study soot formation in laminar counterfl ow diffusion flames. As polycyclic aromatic hydrocarbons (PAHs) are the precursors of soot particles, a detailed gas-phase chemical mechanism describing PAH growth upto coronene for fuels with 1 to 4 carbon atoms was validated against laminar premixed and counter- flow diffusion fl ames. Built upon this gas-phase mechanism, a soot model was then developed to describe soot inception and surface growth. This soot model was sub- sequently used to study fuel mixing effect on soot formation in counterfl ow diffusion flames. Simulation results showed that compared to the baseline case of the ethylene flame, the doping of 5% (by volume) propane or ethane in ethylene tends to increase the soot volume fraction and number density while keeping the average soot size almost unchanged. These results are in agreement with experimental observations. Laser light extinction/scattering as well as laser induced fluorescence techniques were used to study the effect of strain rate on soot and PAH formation in counterfl ow diffusion ames. The results showed that as strain rate increased both soot volume fraction and PAH concentrations decreased. The concentrations of larger PAH were more sensitive to strain rate compared to smaller ones. The effect of CO2 addition on soot formation was also studied using similar experimental techniques. Soot loading was reduced with CO2 dilution. Subsequent numerical modeling studies were able to reproduce the experimental trend. In addition, the chemical effect of CO2 addition was analyzed using numerical data. Critical conditions for the onset of soot were systematically studied in counterfl ow diffusion ames for various gaseous hydrocarbon fuels and at different strain rates. A sooting

  8. Empirical soot formation and oxidation model

    Directory of Open Access Journals (Sweden)

    Boussouara Karima

    2009-01-01

    Full Text Available Modelling internal combustion engines can be made following different approaches, depending on the type of problem to be simulated. A diesel combustion model has been developed and implemented in a full cycle simulation of a combustion, model accounts for transient fuel spray evolution, fuel-air mixing, ignition, combustion, and soot pollutant formation. The models of turbulent combustion of diffusion flame, apply to diffusion flames, which one meets in industry, typically in the diesel engines particulate emission represents one of the most deleterious pollutants generated during diesel combustion. Stringent standards on particulate emission along with specific emphasis on size of emitted particulates have resulted in increased interest in fundamental understanding of the mechanisms of soot particulate formation and oxidation in internal combustion engines. A phenomenological numerical model which can predict the particle size distribution of the soot emitted will be very useful in explaining the above observed results and will also be of use to develop better particulate control techniques. A diesel engine chosen for simulation is a version of the Caterpillar 3406. We are interested in employing a standard finite-volume computational fluid dynamics code, KIVA3V-RELEASE2.

  9. Extraction and identification of organic materials present in soot from a natural gas flame

    Energy Technology Data Exchange (ETDEWEB)

    Vick, R.D.; Avery, M.J.

    1978-01-01

    Aliphatic and polynuclear aromatic hydrocarbons are readily extracted from soot formed from a natural gas flame using methylene chloride and ultrasonic agitation. Identification of 24 organic compounds via capillary column GC retention times and GC-MS data is reported along with details of experimental procedures.

  10. Linkage between [|#11#|]morphology and optical properties of soot

    Science.gov (United States)

    Scarnato, B.; Richard, D. T.; vahidinia, S.; Hillyard, P.; Strawa, A. W.; Kirchstetter, T. W.; Preble, C.; Cuzzi, J. N.

    2011-12-01

    Black Carbon (BC) containing aerosols that are generally hydrophobic upon emission become increasingly mixed with other aerosol material through condensation and coagulation. In polluted urban air, BC becomes internally mixed with organics and sulfate on a time scale of about 12 hours. Recent studies have indicated that the photo-absorption by BC is enhanced as a consequence of the internal mixing of BC with these other aerosol materials. To estimate this absorption enhancement, we have undertaken laboratory studies involving the mixing of initially uncoated BC produced from the combustion of a methane diffusion flame with inorganic and organic compounds. Particle size distributions are used as a first indicator of coating. We use Scanning Electron Microscopy (SEM) to characterize the fractal and shape factors of the generated uncoated and coated BC (see Fig.1 and Fig.2). We create modeled aggregates with the same characteristics as those analyzed at the SEM and we initialize a radiation transfer model (ddscatt) to estimate optical properties of uncoated and coated BC. We quantify absorption enhancement due to coating as a function of aggregate morphology. We use Transmission Electron Microscopy (TEM) to determine the mixing state and to aid in distinguishing between absorption enhancement caused by fractal collapse and surface coating. This paper will show the relationships between soot morphology, coating and optical properties. SEM and TEM imaged of uncoated and coated soot a will be presented.

  11. Residence times and alluvial architecture of a sediment superslug in response to different flow regimes

    Science.gov (United States)

    Moody, John A.

    2017-10-01

    A superslug was deposited in a basin in the Colorado Front Range Mountains as a consequence of an extreme flood following a wildfire disturbance in 1996. The subsequent evolution of this superslug was measured by repeat topographic surveys (31 surveys from 1996 through 2014) of 18 cross sections approximately uniformly spaced over 1500 m immediately above the basin outlet. These surveys allowed the identification within the superslug of chronostratigraphic units deposited and eroded by different geomorphic processes in response to different flow regimes. Over the time period of the study, the superslug went through aggradation, incision, and stabilization phases that were controlled by a shift in geomorphic processes from generally short-duration, episodic, large-magnitude floods that deposited new chronostratigraphic units to long-duration processes that eroded units. These phases were not contemporaneous at each channel cross section, which resulted in a complex response that preserved different chronostratigraphic units at each channel cross section having, in general, two dominant types of alluvial architecture-laminar and fragmented. Age and transit-time distributions for these two alluvial architectures evolved with time since the extreme flood. Because of the complex shape of the distributions they were best modeled by two-parameter Weibull functions. The Weibull scale parameter approximated the median age of the distributions, and the Weibull shape parameter generally had a linear relation that increased with time since the extreme flood. Additional results indicated that deposition of new chronostratigraphic units can be represented by a power-law frequency distribution, and that the erosion of units decreases with depth of burial to a limiting depth. These relations can be used to model other situations with different flow regimes where vertical aggradation and incision are dominant processes, to predict the residence time of possible contaminated

  12. Exposure in emergency general surgery in a time-based residency ...

    African Journals Online (AJOL)

    Objective: This paper aimed to characterize the resident exposure to acute general surgical conditions during a three-months rotation in a general surgical unit. Setting: The Department of Surgery, University of Nairobi and Kenyatta National Referral and Teaching Hospital in Nairobi. MethodS: Four residents (in their first to ...

  13. Organizational and Individual Conditions Associated with Depressive Symptoms among Nursing Home Residents over Time

    Science.gov (United States)

    Cassie, Kimberly M.; Cassie, William E.

    2012-01-01

    Purpose: To examine the effect of organizational culture and climate on depressive symptoms among nursing home residents. Design and Methods: Using a pooled cross-sectional design, this study examines a sample of 23 nursing homes, 1,114 employees, and 5,497 residents. Depressive symptoms were measured using the Minimum Data Set, Depression Rating…

  14. Hydrolysis evolution in a codigestion reactor at various hydraulic residence times

    Directory of Open Access Journals (Sweden)

    Gloria González

    2014-01-01

    Full Text Available The aim of this research is to study the influence of two different hydraulic residence times (HRT's, 5 and 10 days, on the process of hydrolysis-solubilization in a codigestion reactor. Tap water was used to simulate recirculation of a treated leachate. Organic solid waste (OSW from urban solid waste (USW and excess sludge from an urban wastewater treatment plant were first characterized and then treated together by anaerobic codigestion. This was done using a 27.2-L total volume pilot scale bioreactor, which was loaded with equal amounts (w/w of OSW and sludge to a total useful volume of 13-L. The bioreactor was filled with tap water to ensure high humidity. In order to assure suitable mixing and good microbial-substrate contact in the reactor, recirculation of treated effluent was maintained by continuous water flow. The influence of HRT on the process performance was determined through physicochemical characterization of the effluent. Results indicate that HRT is a determinant factor in the efficiency of the system. Reducing HRT increases hydrodynamics and solubilization kinetic rate of organic matter in the bioreactor. Stabilization time of solids is reduced from 20 to 10 days when HRT is shortened from 10 to 5 days.

  15. Plan for radionuclide tracer studies of the residence time distribution in the Wilsonville dissolver and preheater

    Energy Technology Data Exchange (ETDEWEB)

    Jolley, R.L.; Begovich, J.M.; Brashear, H.R.; Case, N.; Clark, T.G.; Emery, J.F.; Patton, B.D.; Rodgers, B.R.; Villiers-Fisher, J.F.; Watson, J.S.

    1983-12-01

    Stimulus-response measurements using radiotracers to measure residence time distribution (RTD) and hydrodynamic parameters for the preheaters and dissolvers at the Ft. Lewis Solvent Refined Coal (SRC) and the Exxon Donor Solvent (EDS) coal conversion pilot plants are reviewed. A plan is also presented for a series of radioactive tracer studies proposed for the Advanced Coal Liquefaction Facility at Wilsonville, Alabama, to measure the RTD for the preheater and dissolvers in the SRC-I mode. The tracer for the gas phase will be /sup 133/Xe, and /sup 198/Au (on carbonized resin or as an aqueous colloidal suspension) will be used as the slurry tracer. Four experimental phases are recommended for the RTD tracer studies: (1) preheater; (2) dissolver with 100% takeoff; (3) dissolver with 100% takeoff and solids withdrawal; and (4) dissolver with 50% takeoff. Eighteen gas-tracer and 22 liquid-tracer injections are projected to accomplish the four experimental phases. Two to four tracer injections are projected for preliminary tests to ensure the capability of safe injection of the radiotracers and the collection of statistically significant data. A complete projected cost and time schedule is provided, including procurement of necessary components, preparation of the radiotracers, assembly and testing of tracer injection apparatus and detection systems, onsite work and tracer injections, laboratory experimentation, data analysis, and report writing.

  16. Plan for radionuclide tracer studies of the residence time distribution in the Wilsonville dissolver and preheater

    International Nuclear Information System (INIS)

    Jolley, R.L.; Begovich, J.M.; Brashear, H.R.

    1983-12-01

    Stimulus-response measurements using radiotracers to measure residence time distribution (RTD) and hydrodynamic parameters for the preheaters and dissolvers at the Ft. Lewis Solvent Refined Coal (SRC) and the Exxon Donor Solvent (EDS) coal conversion pilot plants are reviewed. A plan is also presented for a series of radioactive tracer studies proposed for the Advanced Coal Liquefaction Facility at Wilsonville, Alabama, to measure the RTD for the preheater and dissolvers in the SRC-I mode. The tracer for the gas phase will be 133 Xe, and 198 Au (on carbonized resin or as an aqueous colloidal suspension) will be used as the slurry tracer. Four experimental phases are recommended for the RTD tracer studies: (1) preheater; (2) dissolver with 100% takeoff; (3) dissolver with 100% takeoff and solids withdrawal; and (4) dissolver with 50% takeoff. Eighteen gas-tracer and 22 liquid-tracer injections are projected to accomplish the four experimental phases. Two to four tracer injections are projected for preliminary tests to ensure the capability of safe injection of the radiotracers and the collection of statistically significant data. A complete projected cost and time schedule is provided, including procurement of necessary components, preparation of the radiotracers, assembly and testing of tracer injection apparatus and detection systems, onsite work and tracer injections, laboratory experimentation, data analysis, and report writing

  17. Technical Note: The single particle soot photometer fails to reliably detect PALAS soot nanoparticles

    Directory of Open Access Journals (Sweden)

    M. Gysel

    2012-12-01

    Full Text Available The single particle soot photometer (SP2 uses laser-induced incandescence (LII for the measurement of atmospheric black carbon (BC particles. The BC mass concentration is obtained by combining quantitative detection of BC mass in single particles with a counting efficiency of 100% above its lower detection limit. It is commonly accepted that a particle must contain at least several tenths of a femtogram BC in order to be detected by the SP2.

    Here we show the result that most BC particles from a PALAS spark discharge soot generator remain undetected by the SP2, even if their BC mass, as independently determined with an aerosol particle mass analyser (APM, is clearly above the typical lower detection limit of the SP2. Comparison of counting efficiency and effective density data of PALAS soot with flame generated soot (combustion aerosol standard burner, CAST, fullerene soot and carbon black particles (Cabot Regal 400R reveals that particle morphology can affect the SP2's lower detection limit. PALAS soot particles are fractal-like agglomerates of very small primary particles with a low fractal dimension, resulting in a very low effective density. Such loosely packed particles behave like "the sum of individual primary particles" in the SP2's laser. Accordingly, most PALAS soot particles remain undetected as the SP2's laser intensity is insufficient to heat the primary particles to their vaporisation temperature because of their small size (Dpp ≈ 5–10 nm. Previous knowledge from pulsed laser-induced incandescence indicated that particle morphology might have an effect on the SP2's lower detection limit, however, an increase of the lower detection limit by a factor of ∼5–10, as reported here for PALAS soot, was not expected.

    In conclusion, the SP2's lower detection limit at a certain laser power depends primarily on the total BC mass per particle for compact particles with sufficiently high effective

  18. Accessing doctors at times of need-measuring the distance tolerance of rural residents for health-related travel.

    Science.gov (United States)

    McGrail, Matthew Richard; Humphreys, John Stirling; Ward, Bernadette

    2015-05-29

    Poor access to doctors at times of need remains a significant impediment to achieving good health for many rural residents. The two-step floating catchment area (2SFCA) method has emerged as a key tool for measuring healthcare access in rural areas. However, the choice of catchment size, a key component of the 2SFCA method, is problematic because little is known about the distance tolerance of rural residents for health-related travel. Our study sought new evidence to test the hypothesis that residents of sparsely settled rural areas are prepared to travel further than residents of closely settled rural areas when accessing primary health care at times of need. A questionnaire survey of residents in five small rural communities of Victoria and New South Wales in Australia was used. The two outcome measures were current travel time to visit their usual doctor and maximum time prepared to travel to visit a doctor, both for non-emergency care. Kaplan-Meier charts were used to compare the association between increased distance and decreased travel propensity for closely-settled and sparsely-settled areas, and ordinal multivariate regression models tested significance after controlling for health-related travel moderating factors and town clustering. A total of 1079 questionnaires were completed with 363 from residents in closely-settled locations and 716 from residents in sparsely-settled areas. Residents of sparsely-settled communities travel, on average, 10 min further than residents of closely-settled communities (26.3 vs 16.9 min, p time prepared to travel (54.1 vs 31.9 min, p time remained significant after controlling for demographic and other constraints to access, such as transport availability or difficulties getting doctor appointments, as well as after controlling for town clustering and current travel times. Improved geographical access remains a key issue underpinning health policies designed to improve the provision of rural primary health care

  19. Residence times of groundwater and nitrate transport in coastal aquifer systems: Daweijia area, northeastern China

    Energy Technology Data Exchange (ETDEWEB)

    Han, Dongmei [Key Laboratory of Water Cycle & Related Land Surface Processes, Institute of Geographic Sciences and Natural Resources Research, Chinese Academy of Sciences, Beijing 100101 (China); National Centre for Groundwater Research and Training, Flinders University, GPO Box 2100, Adelaide, SA 5001 (Australia); Cao, Guoliang [National Centre for Groundwater Research and Training, Flinders University, GPO Box 2100, Adelaide, SA 5001 (Australia); Center for Water Research, College of Engineering, Peking University, Beijing 100871 (China); McCallum, James [National Centre for Groundwater Research and Training, Flinders University, GPO Box 2100, Adelaide, SA 5001 (Australia); School of the Environment, Flinders University, GPO Box 2100, Adelaide, SA 5001 (Australia); Song, Xianfang [Key Laboratory of Water Cycle & Related Land Surface Processes, Institute of Geographic Sciences and Natural Resources Research, Chinese Academy of Sciences, Beijing 100101 (China)

    2015-12-15

    Groundwater within the coastal aquifer systems of the Daweijia area in northeastern China is characterized by a large of variations (33–521 mg/L) in NO{sub 3}{sup −} concentrations. Elevated nitrate concentrations, in addition to seawater intrusion in the Daweijia well field, both attributable to anthropogenic activities, may impact future water-management practices. Chemical and stable isotopic (δ{sup 18}O, δ{sup 2}H) analysis, {sup 3}H and CFCs methods were applied to provide a better understanding of the relationship between the distribution of groundwater mean residence time (MRT) and nitrate transport, and to identify sources of nitrate concentrations in the complex coastal aquifer systems. There is a relatively narrow range of isotopic composition (ranging from − 8.5 to − 7.0‰) in most groundwater. Generally higher tritium contents observed in the wet season relative to the dry season may result from rapid groundwater circulation in response to the rainfall through the preferential flow paths. In the well field, the relatively increased nitrate concentrations of groundwater, accompanied by the higher tritium contents in the wet season, indicate the nitrate pollution can be attributed to domestic wastes. The binary exponential and piston-flow mixing model (BEP) yielded feasible age distributions based on the conceptual model. The good inverse relationship between groundwater MRTs (92–467 years) and the NO{sub 3}{sup −} concentrations in the shallow Quaternary aquifers indicates that elevated nitrate concentrations are attributable to more recent recharge for shallow groundwater. However, there is no significant relationship between the MRTs (8–411 years) and the NO{sub 3}{sup −} concentrations existing in the carbonate aquifer system, due to the complex hydrogeological conditions, groundwater age distributions and the range of contaminant source areas. Nitrate in the groundwater system without denitrification effects could accumulate and be

  20. How Do Residents Spend Their Shift Time? A Time and Motion Study With a Particular Focus on the Use of Computers.

    Science.gov (United States)

    Mamykina, Lena; Vawdrey, David K; Hripcsak, George

    2016-06-01

    To understand how much time residents spend using computers compared with other activities, and what residents use computers for. This time and motion study was conducted in June and July 2010 at NewYork-Presbyterian/Columbia University Medical Center with seven residents (first-, second-, and third-year) on the general medicine service. An experienced observer shadowed residents during a single day shift, captured all their activities using an iPad application, and took field notes. The activities were captured using a validated taxonomy of clinical activities, expanded to describe computer-based activities with a greater level of detail. Residents spent 364.5 minutes (50.6%) of their shift time using computers, compared with 67.8 minutes (9.4%) interacting with patients. In addition, they spent 292.3 minutes (40.6%) talking with others in person, 186.0 minutes (25.8%) handling paper notes, 79.7 minutes (11.1%) in rounds, 80.0 minutes (11.1%) walking or waiting, and 54.0 minutes (7.5%) talking on the phone. Residents spent 685 minutes (59.6%) multitasking. Computer-based documentation activities amounted to 189.9 minutes (52.1%) of all computer-based activities time, with 128.7 minutes (35.3%) spent writing notes and 27.3 minutes (7.5%) reading notes composed by others. The study showed that residents spent considerably more time interacting with computers (over 50% of their shift time) than in direct contact with patients (less than 10% of their shift time). Some of this may be due to an increasing reliance on computing systems for access to patient data, further exacerbated by inefficiencies in the design of the electronic health record.

  1. Time-motion studies of internal medicine residents' duty hours: a systematic review and meta-analysis.

    Science.gov (United States)

    Leafloor, Cameron W; Lochnan, Heather A; Code, Catherine; Keely, Erin J; Rothwell, Deanna M; Forster, Alan J; Huang, Allen R

    2015-01-01

    Since the mid-1980s, medical residents' long duty hours have been under scrutiny as a factor affecting patient safety and the work environment for the residents. After several mandated changes in duty hours, it is important to understand how residents spend their time before proposing and implementing future changes. Time-motion methodology may provide reliable information on what residents do while on duty. The purpose of this study is to review all available literature pertaining to time-motion studies of internal medicine residents while on a medicine service and to understand how much of their time is apportioned to various categories of tasks, and also to determine the effects of the Accreditation Council for Graduate Medical Education (ACGME)-mandated duty hour changes on resident workflow in North America. Electronic bibliographic databases were searched for articles in English between 1941 and April 2013 reporting time-motion studies of internal medicine residents rotating through a general medicine service. Eight articles were included. Residents spent 41.8% of time in patient care activities, 18.1% communicating, 13.8% in educational activities, 19.7% in personal/other, and 6.6% in transit. North American data showed the following changes after the implementation of the ACGME 2003 duty hours standard: patient care activities from 41.8% to 40.8%, communication activities from 19.0% to 22.3%, educational activities from 17.7% to 11.6%, and personal/other activities from 21.5% to 17.1%. There was a paucity of time-motion data. There was great variability in the operational definitions of task categories reported in the studies. Implementation of the ACGME duty hour standards did not have a significant effect on the percentage of time spent in particular tasks. There are conflicting reports on how duty hour changes have affected patient safety. A low proportion of time spent in educational activities deserves further study and may point to a review of the

  2. Milk performance of two cow breeds at two levels of supplementation in long residence time grazing paddocks

    OpenAIRE

    Roca Fernandez, Ana Isabel; González-Rodríguez, Antonio; Leurent, S.; López-Mosquera, M.E.; Gallard, Yves; Delaby, Luc

    2012-01-01

    Milk performance of four groups of cows (H0, H4, N0 and N4) was studied under grazing: two cow breeds, Holstein-Friesian (H) vs. Normande (N), supplemented at pasture with two levels of concentrate, low vs. high (0 and 4 kg cow–1 day–1). A simplified rotational grazing system using three paddocks per rotation with a mean residence time per paddock of 10-days was examined. During this long residence time, maximum milk yield (MY max.) was reached at day 4 followed by a milk yield drop (Dm) at t...

  3. Estimation of sediment residence times in subtropical highland catchments of central Mexico combining river gauging and fallout radionuclides

    Science.gov (United States)

    Evrard, Olivier; Némery, Julien; Gratiot, Nicolas; Duvert, Clément; Lefèvre, Irène; Ayrault, Sophie; Esteves, Michel; Bonté, Philippe

    2010-05-01

    Subtropical regions of the world are affected by intense soil erosion associated with deforestation, overgrazing and cropping intensification. This land degradation leads to important on-site (e.g. decrease in soil fertility) and off-site impacts (e.g. reservoir sedimentation, water pollution). This study determined the mean sediment residence times in soils and rivers of three catchments (3 - 12 km²) with contrasted land uses (i.e. cropland, forests, rangelands, extended gully networks) located in highlands of the transvolcanic belt of central Mexico. Calculations were based on rainfall and river gauging as well as on fallout radionuclide measurements (Be-7, Cs-137, Pb-210). Atmospheric deposition of Be-7 and Pb-210 was estimated based on the analysis of rainfall precipitated samples. Rainfall samples were collected all throughout the rainy season in order to take account of the temporal variations of the radionuclide fluxes. Furthermore, sampling of suspended sediment was conducted at the outlet of each catchment during most of the storms that occurred throughout the 2009 rainy season. Be-7, Cs-137 and Pb-210 concentrations of this sediment were determined by gamma-spectrometry. A two-box balance model was then used to estimate the sediment residence time and the inventory of radionuclides in the three selected catchments. This model subdivided each catchment into two boxes: (i) a "soil-box" characterised by low transport velocities and hence long radionuclide residence times and (ii) a "river-box" covering the river surface and its surroundings characterised by quicker exchanges and shorter radionuclide residence times. Input and output fluxes of sediment and radionuclides were taken into account in each box. Radioactive decay during the residence time of sediment was also considered. The mean residence time of sediment in soils ranged between 13,300 - 28,500 years. In contrast, sediment residence time in rivers was much shorter, fluctuating between 28 and 393

  4. Impact of repository depth on residence times for leaking radionuclides in land-based surface water

    Science.gov (United States)

    Wörman, Anders; Marklund, Lars; Xu, Shulan; Dverstorp, Björn

    2007-03-01

    The multiple scales of landscape topography produce a wide distribution of groundwater circulation cells that control the hydro-geological environments surrounding geological repositories for nuclear waste. The largest circulation cells tend to discharge water into major river reaches, large freshwater systems or the nearby Baltic Sea. We investigated numerically the release of radionuclides from repositories placed in bedrock with depths between 100 to 2000 meters in a Swedish coastal area and found that leakage from the deeper positions emerges primarily in the major aquatic systems. In effect, radionuclides from the deeper repositories are more rapidly transported towards the Sea by the stream system compared to leakage from more shallow repositories. The release from the shallower repositories is significantly retained in the initial stage of the transport in the (superficial) landscape because the discharge occurs in or near low-order streams with high retention characteristics. This retention and residence time for radioactivity in the landscape control radiological doses to biota and can, thus, be expected to constitute an essential part of an associated risk evaluation.

  5. Relationship between fiber degradation and residence time distribution in the processing of long fiber reinforced thermoplastics

    Directory of Open Access Journals (Sweden)

    2008-08-01

    Full Text Available Long fiber reinforced thermoplastics (LFT were processed by in-line compounding equipment with a modified single screw extruder. A pulse stimulus response technique using PET spheres as the tracer was adopted to obtain residence time distribution (RTD of extrusion compounding. RTD curves were fitted by the model based on the supposition that extrusion compounding was the combination of plug flow and mixed flow. Characteristic parameters of RTD model including P the fraction of plug flow reactor (PFR and d the fraction of dead volume of continuous stirred tank reactor (CSTR were used to associate with fiber degradation presented by fiber length and dispersion. The effects of screw speed, mixing length and channel depth on RTD curves, and characteristic parameters of RTD models as well as their effects on the fiber degradation were investigated. The influence of shear force with different screw speeds and variable channel depth on fiber degradation was studied and the main impetus of fiber degradation was also presented. The optimal process for obtaining the balance of fiber length and dispersion was presented.

  6. Investigation of residence time and groundwater flux in Venice Lagoon: comparing radium isotope and hydrodynamic models.

    Science.gov (United States)

    Rapaglia, John; Ferrarin, Christian; Zaggia, Luca; Moore, Willard S; Umgiesser, Georg; Garcia-Solsona, Ester; Garcia-Orellana, Jordi; Masqué, Pere

    2010-07-01

    The four naturally-occurring isotopes of radium were coupled with a previously evaluated hydrodynamic model to determine the apparent age of surface waters and to quantify submarine groundwater discharge (SGD) into the Venice Lagoon, Italy. Mean apparent age of water in the Venice Lagoon was calculated using the ratio of 224Ra to 228Ra determined from 30 monitoring stations and a mean pore water end member. Average apparent age was calculated to be 6.0 d using Ra ratios. This calculated age was very similar to average residence time calculated for the same period using a hydrodynamic model (5.8 d). A mass balance of Ra was accomplished by quantifying each of the sources and sinks of Ra in the lagoon, with the unknown variable being attributed to SGD. Total SGD were calculated to be 4.1 +/- 1.5, 3.8 +/- 0.7, 3.0 +/- 1.3, and 3.5 +/- 1.0 x 10(10) L d(-1) for (223,224,226, 228)Ra, respectively, which are an order of magnitude larger than total mean fluvial discharge into the Venice Lagoon (3.1 x 10(9) L d(-1)). The SGD as a source of nutrients in the Venice Lagoon is also discussed and, though significant to the nutrient budget, is likely to be less important as the dominant control on SGD is recirculated seawater rather than freshwater. 2009 Elsevier Ltd. All rights reserved.

  7. Elucidating the Origin of Long Residence Time Binding for Inhibitors of the Metalloprotease Thermolysin.

    Science.gov (United States)

    Cramer, Jonathan; Krimmer, Stefan G; Fridh, Veronica; Wulsdorf, Tobias; Karlsson, Robert; Heine, Andreas; Klebe, Gerhard

    2017-01-20

    Kinetic parameters of protein-ligand interactions are progressively acknowledged as valuable information for rational drug discovery. However, a targeted optimization of binding kinetics is not easy to achieve, and further systematic studies are necessary to increase the understanding about molecular mechanisms involved. We determined association and dissociation rate constants for 17 inhibitors of the metalloprotease thermolysin by surface plasmon resonance spectroscopy and correlated kinetic data with high-resolution crystal structures in complex with the protein. From the structure-kinetics relationship, we conclude that the strength of interaction with Asn112 correlates with the rate-limiting step of dissociation. This residue is located at the beginning of a β-strand motif that lines the binding cleft and is commonly believed to align a substrate for catalysis. A reduced mobility of the Asn112 side chain owing to an enhanced engagement in charge-assisted hydrogen bonds prevents the conformational adjustment associated with ligand release and transformation of the enzyme to its open state. This hypothesis is supported by kinetic data of ZF P LA, a known pseudopeptidic inhibitor of thermolysin, which blocks the conformational transition of Asn112. Interference with this retrograde induced-fit mechanism results in variation of the residence time of thermolysin inhibitors by a factor of 74 000. The high conservation of this structural motif within the M4 and M13 metalloprotease families underpins the importance of this feature and has significant implications for drug discovery.

  8. Subunit Stabilization and Polyethylene Glycolation of Cocaine Esterase Improves In Vivo Residence Time

    Energy Technology Data Exchange (ETDEWEB)

    Narasimhan, Diwahar; Collins, Gregory T.; Nance, Mark R.; Nichols, Joseph; Edwald, Elin; Chan, Jimmy; Ko, Mei-Chuan; Woods, James H.; Tesmer, John J.G.; Sunahara, Roger K. (Michigan)

    2012-03-15

    No small-molecule therapeutic is available to treat cocaine addiction, but enzyme-based therapy to accelerate cocaine hydrolysis in serum has gained momentum. Bacterial cocaine esterase (CocE) is the fastest known native enzyme that hydrolyzes cocaine. However, its lability at 37 C has limited its therapeutic potential. Cross-linking subunits through disulfide bridging is commonly used to stabilize multimeric enzymes. Herein we use structural methods to guide the introduction of two cysteine residues within dimer interface of CocE to facilitate intermolecular disulfide bond formation. The disulfide-crosslinked enzyme displays improved thermostability, particularly when combined with previously described mutations that enhance stability (T172R-G173Q). The newly modified enzyme yielded an extremely stable form of CocE (CCRQ-CocE) that retained greater than 90% of its activity after 41 days at 37 C, representing an improvement of more than 4700-fold over the wild-type enzyme. CCRQ-CocE could also be modified by polyethylene glycol (PEG) polymers, which improved its in vivo residence time from 24 to 72 h, as measured by a cocaine lethality assay, by self-administration in rodents, and by measurement of inhibition of cocaine-induced cardiovascular effects in rhesus monkeys. PEG-CCRQ elicited negligible immune response in rodents. Subunit stabilization and PEGylation has thus produced a potential protein therapeutic with markedly higher stability both in vitro and in vivo.

  9. Optimized Inhibitors of Soluble Epoxide Hydrolase Improve in Vitro Target Residence Time and in Vivo Efficacy

    Science.gov (United States)

    2015-01-01

    Diabetes is affecting the life of millions of people. A large proportion of diabetic patients suffer from severe complications such as neuropathic pain, and current treatments for these complications have deleterious side effects. Thus, alternate therapeutic strategies are needed. Recently, the elevation of epoxy-fatty acids through inhibition of soluble epoxide hydrolase (sEH) was shown to reduce diabetic neuropathic pain in rodents. In this report, we describe a series of newly synthesized sEH inhibitors with at least 5-fold higher potency and doubled residence time inside both the human and rodent sEH enzyme than previously reported inhibitors. These inhibitors also have better physical properties and optimized pharmacokinetic profiles. The optimized inhibitor selected from this new series displayed improved efficacy of almost 10-fold in relieving pain perception in diabetic neuropathic rats as compared to the approved drug, gabapentin, and previously published sEH inhibitors. Therefore, these new sEH inhibitors could be an attractive alternative to treat diabetic neuropathy in humans. PMID:25079952

  10. Relating hyporheic fluxes, residence times, and redox-sensitive biogeochemical processes upstream of beaver dams

    Science.gov (United States)

    Briggs, Martin A.; Lautz, Laura; Hare, Danielle K.

    2013-01-01

    Abstract. Small dams enhance the development of patchy microenvironments along stream corridors by trapping sediment and creating complex streambed morphologies. This patchiness drives intricate hyporheic flux patterns that govern the exchange of O2 and redox-sensitive solutes between the water column and the stream bed. We used multiple tracer techniques, naturally occurring and injected, to evaluate hyporheic flow dynamics and associated biogeochemical cycling and microbial reactivity around 2 beaver dams in Wyoming (USA). High-resolution fiber-optic distributed temperature sensing was used to collect temperature data over 9 vertical streambed profiles and to generate comprehensive vertical flux maps using 1-dimensional (1-D) heat-transport modeling. Coincident with these locations, vertical profiles of hyporheic water were collected every week and analyzed for dissolved O2, pH, dissolved organic C, and several conservative and redox-sensitive solutes. In addition, hyporheic and net stream aerobic microbial reactivity were analyzed with a constant-rate injection of the biologically sensitive resazurin (Raz) smart tracer. The combined results revealed a heterogeneous system with rates of downwelling hyporheic flow organized by morphologic unit and tightly coupled to the redox conditions of the subsurface. Principal component analysis was used to summarize the variability of all redox-sensitive species, and results indicated that hyporheic water varied from oxic-stream-like to anoxic-reduced in direct response to the hydrodynamic conditions and associated residence times. The anaerobic transition threshold predicted by the mean O2 Damko

  11. Drug-target residence time--a case for G protein-coupled receptors.

    Science.gov (United States)

    Guo, Dong; Hillger, Julia M; IJzerman, Adriaan P; Heitman, Laura H

    2014-07-01

    A vast number of marketed drugs act on G protein-coupled receptors (GPCRs), the most successful category of drug targets to date. These drugs usually possess high target affinity and selectivity, and such combined features have been the driving force in the early phases of drug discovery. However, attrition has also been high. Many investigational new drugs eventually fail in clinical trials due to a demonstrated lack of efficacy. A retrospective assessment of successfully launched drugs revealed that their beneficial effects in patients may be attributed to their long drug-target residence times (RTs). Likewise, for some other GPCR drugs short RT could be beneficial to reduce the potential for on-target side effects. Hence, the compounds' kinetics behavior might in fact be the guiding principle to obtain a desired and durable effect in vivo. We therefore propose that drug-target RT should be taken into account as an additional parameter in the lead selection and optimization process. This should ultimately lead to an increased number of candidate drugs moving to the preclinical development phase and on to the market. This review contains examples of the kinetics behavior of GPCR ligands with improved in vivo efficacy and summarizes methods for assessing drug-target RT. © 2014 Wiley Periodicals, Inc.

  12. Scrutinizing the carbon cycle and CO2 residence time in the atmosphere

    Science.gov (United States)

    Harde, Hermann

    2017-05-01

    Climate scientists presume that the carbon cycle has come out of balance due to the increasing anthropogenic emissions from fossil fuel combustion and land use change. This is made responsible for the rapidly increasing atmospheric CO2 concentrations over recent years, and it is estimated that the removal of the additional emissions from the atmosphere will take a few hundred thousand years. Since this goes along with an increasing greenhouse effect and a further global warming, a better understanding of the carbon cycle is of great importance for all future climate change predictions. We have critically scrutinized this cycle and present an alternative concept, for which the uptake of CO2 by natural sinks scales proportional with the CO2 concentration. In addition, we consider temperature dependent natural emission and absorption rates, by which the paleoclimatic CO2 variations and the actual CO2 growth rate can well be explained. The anthropogenic contribution to the actual CO2 concentration is found to be 4.3%, its fraction to the CO2 increase over the Industrial Era is 15% and the average residence time 4 years.

  13. Alongshore Variation in the Depth of Activation: Implications of Oil Residence Time

    Science.gov (United States)

    Flores, P.; Houser, C.

    2016-12-01

    In 2010 the Deepwater Horizon Oil Spill released approximately 5 million barrels of oil into the Gulf of Mexico just as the nearshore and beach profile were recovering from winter storms. As a consequence, oil mats and tar balls were trapped at depth within the beach and nearshore profile. Excavation of this buried oil during subsequent storms creates the potential for the contamination of adjacent beaches and the degradation of marine ecosystems, which can in turn negatively impact local economies that depend on fisheries and tourism. The potential for oil burial and persistence is dependent on four things: the physio-chemical nature of the oil as it reaches the nearshore environment, the pre-existing morphology of the beach and nearshore, and the evolution of that morphology after the oil is deposited. The depth at which the oil is buried is also dependent on the beach profile during the time of the spill. The purpose of this study is to characterize the alongshore variation in depth of activation on a Deepwater Horizon impacted section of Pensacola Beach, Florida with regards to the implications of oil residence time. Ground- Penetrating Radar (GPR) surveys were conducted along two parallel 1-km transects adjacent to the swash zone and the dune. Additional cross- shore transects were completed every 150 m from the base of the dune to the top of the swash zone. Sediments cores were taken at the crossing points of the alongshore and cross-shore transects, to calibrate the GPR surveys and complete an elemental analysis for the identification of storm layers. The cores were also analyzed for the presence of buried oil.

  14. Temperature sensitivity of soil organic carbon decomposition increased with mean carbon residence time: Field incubation and data assimilation.

    Science.gov (United States)

    Zhou, Xuhui; Xu, Xia; Zhou, Guiyao; Luo, Yiqi

    2018-02-01

    Temperature sensitivity of soil organic carbon (SOC) decomposition is one of the major uncertainties in predicting climate-carbon (C) cycle feedback. Results from previous studies are highly contradictory with old soil C decomposition being more, similarly, or less sensitive to temperature than decomposition of young fractions. The contradictory results are partly from difficulties in distinguishing old from young SOC and their changes over time in the experiments with or without isotopic techniques. In this study, we have conducted a long-term field incubation experiment with deep soil collars (0-70 cm in depth, 10 cm in diameter of PVC tubes) for excluding root C input to examine apparent temperature sensitivity of SOC decomposition under ambient and warming treatments from 2002 to 2008. The data from the experiment were infused into a multi-pool soil C model to estimate intrinsic temperature sensitivity of SOC decomposition and C residence times of three SOC fractions (i.e., active, slow, and passive) using a data assimilation (DA) technique. As active SOC with the short C residence time was progressively depleted in the deep soil collars under both ambient and warming treatments, the residences times of the whole SOC became longer over time. Concomitantly, the estimated apparent and intrinsic temperature sensitivity of SOC decomposition also became gradually higher over time as more than 50% of active SOC was depleted. Thus, the temperature sensitivity of soil C decomposition in deep soil collars was positively correlated with the mean C residence times. However, the regression slope of the temperature sensitivity against the residence time was lower under the warming treatment than under ambient temperature, indicating that other processes also regulated temperature sensitivity of SOC decomposition. These results indicate that old SOC decomposition is more sensitive to temperature than young components, making the old C more vulnerable to future warmer

  15. Effects of Surgical Assistant's Level of Resident Training on Surgical Treatment of Intermittent Exotropia: Operation Time and Surgical Outcomes.

    Science.gov (United States)

    Kim, Moo Hyun; Chung, Hyunuk; Kim, Won Jae; Kim, Myung Mi

    2018-02-01

    To evaluate the effects of the surgical assistant's level of resident training on operation time and surgical outcome in the surgical treatment of intermittent exotropia. This study included 456 patients with intermittent exotropia who underwent lateral rectus recession and medial rectus resection and were followed up for 24 months after surgery. The patients were divided into two groups according to the surgical assistant's level of resident training: group F (surgery assisted by a first-year resident [n = 198]) and group S (surgery assisted by a second-, third-, or fourth-year resident [n = 258]). The operation time and surgical outcomes (postoperative exodeviation and the number of patients who underwent a second operation) were compared between the two groups. The average operation times in groups F and S were 36.54 ± 7.4 and 37.34 ± 9.94 minutes, respectively (p = 0.33). Immediate postoperative exodeviation was higher in group F (0.79 ± 3.82 prism diopters) than in group S (0.38 ± 3.75 prism diopters). However, repeated-measures analysis of variance revealed no significant difference in exodeviation between the two groups during the 24-month follow-up period (p = 0.45). A second operation was performed in 29.3% (58 / 198) of the patients in group F, and in 32.2% (83 / 258) of those in group S (p = 0.51). No significant difference in operation time was observed when we compared the effects of the level of resident training in the surgical treatment of intermittent exotropia. Although the immediate postoperative exodeviation was higher in patients who had undergone surgery assisted by a first-year resident, the surgical outcome during the 24-month follow-up was not significantly different.

  16. Soot particle size measurements in ethylene diffusion flames at elevated pressures

    KAUST Repository

    Steinmetz, Scott

    2016-05-07

    Soot particle size is investigated in laminar nitrogen-diluted ethylene coflow diffusion flames at 4, 8, 12 and 16 atm. Line of sight attenuation and scattering are used to measure two-dimensional soot volume fraction and particle size fields for the first time at elevated pressures. Soot volume fraction dependence on pressure is consistent with the observations of similar studies, scaling approximately with the square of pressure. Scattering intensity is analyzed through Rayleigh and Rayleigh-Debye-Gans polydisperse fractal aggregate theories to provide two estimates of particle size. An increase in overall particle sizes with pressure is found, consistent with similar one-dimensional studies. Particle diameters in the annulus of the flame increase faster with pressure than those on centerline. Contrary to previous studies, the dependence of particle size on pressure was found to taper off between 8 and 12 atm, with little observed growth beyond 12 atm. The measurements provide additional data for one of the International Sooting Flame (ISF) workshop\\'s target pressurized flames.

  17. Importance of powder residence time for the aerosol delivery performance of a commercial dry powder inhaler Aerolizer(®).

    Science.gov (United States)

    Jiang, Liqun; Tang, Yue; Zhang, Hongjiu; Lu, Xifeng; Chen, Xijing; Zhu, Jiabi

    2012-10-01

    The performance of dry powder aerosol delivery systems depends not only on the powder formulation but also on the dry powder inhalers (DPIs). Effects of turbulence, grid, mouthpiece, inlet size, air flow, and capsule on the DPIs performance have been investigated previously. Considering powder dispersion in DPIs is a time-dependent process, the powder residence time in DPIs is supposed to have a great impact on DPIs efficiency. This study sought to investigate the effect of powder residence time on the performance of a commercial DPI Aerolizer(®). A standard Aerolizer(®) (SD) and five modified devices (MD1, MD2, MD3, MD4, and MD5) were employed for this research. Computational fluid dynamics analysis was used to calculate the flow field and the powder residence time in these devices. Recombinant human interleukin-2 inhalation powders and a twin impinger were used for the deposition experiment. The powder mean residence time in the secondary atomization zone of the devices was increased from 0 ms for SD to 0.33, 0.96, 1.42, 1.76, and 2.14 ms for MD1, MD2, MD3, MD4, and MD5, respectively. At a flow rate of 60 L/min, with an increase in the powder residence time in these devices, a significant gradual and increasing trend in the powder respirable fraction was observed from 29.1%± 1.1% (MD1) to 32.6% ± 2.2% (MD2), 37.1% ± 1.1% (MD3), and 43.7% ± 2.1% (MD4). There was no significant difference in the powder respirable fraction between SD and MD1 or between MD4 and MD5. Within a certain range, increasing the powder residence time could improve the performance of Aerolizer(®) by increasing the powder-air interaction time (the main reason) and increasing the powder-device compaction (the secondary reason). Combination of high turbulence level and sufficient powder residence time could further improve the device performance.

  18. Aromatics oxidation and soot formation in flames

    Energy Technology Data Exchange (ETDEWEB)

    Howard, J.B.; Pope, C.J.; Shandross, R.A.; Yadav, T. [Massachusetts Institute of Technology, Cambridge (United States)

    1993-12-01

    This project is concerned with the kinetics and mechanisms of aromatics oxidation and soot and fullerenes formation in flames. The scope includes detailed measurements of profiles of stable and radical species concentrations in low-pressure one-dimensional premixed flames. Intermediate species identifications and mole fractions, fluxes, and net reaction rates calculated from the measured profiles are used to test postulated reaction mechanisms. Particular objectives are to identify and to determine or confirm rate constants for the main benzene oxidation reactions in flames, and to characterize fullerenes and their formation mechanisms and kinetics.

  19. Groundwater residence time and movement in the Maltese islands - A geochemical approach

    Energy Technology Data Exchange (ETDEWEB)

    Stuart, M.E., E-mail: mest@bgs.ac.uk [British Geological Survey, Wallingford, Oxfordshire OX10 8BB (United Kingdom); Maurice, L. [British Geological Survey, Wallingford, Oxfordshire OX10 8BB (United Kingdom); Heaton, T.H.E. [British Geological Survey, NERC Isotope Geoscience Laboratory, Keyworth, Nottinghamshire NG12 5GG (United Kingdom); Sapiano, M.; Micallef Sultana, M. [Malta Resources Authority, Marsa MRS 9065 (Malta); Gooddy, D.C.; Chilton, P.J. [British Geological Survey, Wallingford, Oxfordshire OX10 8BB (United Kingdom)

    2010-05-15

    The Maltese islands are composed of two limestone aquifers, the Upper and Lower Coralline Limestone separated by an aquitard, the 'Blue Clay'. The Lower Coralline Limestone is overlain in part by the poorly permeable Globigerina Limestone. The upper perched aquifers are discontinuous and have very limited saturated thickness and a short water level response time to rainfall. Frequent detections of coliforms suggest a rapid route to groundwater. However, the unsaturated zone has a considerable thickness in places and the primary porosity of the Upper Coralline Limestone is high, so there is likely to be older recharge by slow matrix flow as well as rapid recharge from fractures. Measurement of SF{sub 6} from a pumping station in a deep part of one of the perched aquifers indicated a mean saturated zone age of about 15 a. The Main Sea Level aquifers (MSL) on both Malta and Gozo have a large unsaturated thickness as water levels are close to sea level. On Malta, parts of the aquifer are capped by the perched aquifers and more extensively by the Globigerina Limestone. The limited detection of coliform bacteria suggests only some rapid recharge from the surface via fractures or karst features. Transmissivity is low and {sup 3}H and CFC/SF{sub 6} data indicate that saturated zone travel times are in the range 15-40 a. On Gozo the aquifer is similar but is more-extensively capped by impermeable Blue Clay. CFC data show the saturated zone travel time is from 25 a to possibly more than 60 a. Groundwater age is clearly related to the extent of low-permeability cover. The {delta}{sup 13}C signature of groundwater is related to the geochemical processes which occur along the flowpath and is consistent with residence time ages in the sequence; perched aquifers < Malta MSL < Gozo MSL. The {sup 18}O and {sup 2}H enriched isotopic signature of post 1983 desalinated water can be seen in more-modern groundwater, particularly the urbanized areas of the perched and Malta MSL

  20. Fractal-like dimension of nanometer Diesel soot particles

    Energy Technology Data Exchange (ETDEWEB)

    Skillas, G.; Baltensperger, U. [Paul Scherrer Inst. (PSI), Villigen (Switzerland); Siegmann, K. [Eidgenoessische Technische Hochschule, Zurich (Switzerland)

    1997-11-01

    Measurements with a low-pressure impactor and a differential mobility analyser were conducted for Diesel soot at various engine loads. By means of these measurements a fractal-like dimension of Diesel soot particles, with diameters ranging from 55 up to 260 nm, was established. (author) 2 figs., 7 refs.

  1. Modeling polychlorinated biphenyl sorption isotherms for soot and coal

    NARCIS (Netherlands)

    Jantunen, A.P.K.; Koelmans, A.A.; Jonker, M.T.O.

    2010-01-01

    Sorption isotherms (pg-ng/L) were measured for 11 polychlorinated biphenyls (PCBs) of varying molecular planarity from aqueous solution to two carbonaceous geosorbents, anthracite coal and traffic soot. All isotherms were reasonably log-log-linear, but smooth for traffic soot and staircase-shaped

  2. Implementation and evaluation of a simulation curriculum for paediatric residency programs including just-in-time in situ mock codes.

    Science.gov (United States)

    Sam, Jonathan; Pierse, Michael; Al-Qahtani, Abdullah; Cheng, Adam

    2012-02-01

    To develop, implement and evaluate a simulation-based acute care curriculum in a paediatric residency program using an integrated and longitudinal approach. Curriculum framework consisting of three modular, year-specific courses and longitudinal just-in-time, in situ mock codes. Paediatric residency program at BC Children's Hospital, Vancouver, British Columbia. The three year-specific courses focused on the critical first 5 min, complex medical management and crisis resource management, respectively. The just-in-time in situ mock codes simulated the acute deterioration of an existing ward patient, prepared the actual multidisciplinary code team, and primed the surrounding crisis support systems. Each curriculum component was evaluated with surveys using a five-point Likert scale. A total of 40 resident surveys were completed after each of the modular courses, and an additional 28 surveys were completed for the overall simulation curriculum. The highest Likert scores were for hands-on skill stations, immersive simulation environment and crisis resource management teaching. Survey results also suggested that just-in-time mock codes were realistic, reinforced learning, and prepared ward teams for patient deterioration. A simulation-based acute care curriculum was successfully integrated into a paediatric residency program. It provides a model for integrating simulation-based learning into other training programs, as well as a model for any hospital that wishes to improve paediatric resuscitation outcomes using just-in-time in situ mock codes.

  3. Linking granulation performance with residence time and granulation liquid distributions in twin-screw granulation: An experimental investigation

    DEFF Research Database (Denmark)

    Kumar, Ashish; Alakarjula, Maija; Vanhoorne, Valérie

    2016-01-01

    elements in the granulator screw allowing the production of granules with a size distribution appropriate for tableting. The distribution of residence time and granulation liquid is governed by the field conditions (such as location and length of mixing zones) in the twin-screw granulator, thus contain...

  4. The decadal state of the terrestrial carbon cycle : Global retrievals of terrestrial carbon allocation, pools, and residence times

    NARCIS (Netherlands)

    Bloom, A Anthony; Exbrayat, Jean-François; van der Velde, Ivar R; Feng, Liang; Williams, Mathew

    2016-01-01

    The terrestrial carbon cycle is currently the least constrained component of the global carbon budget. Large uncertainties stem from a poor understanding of plant carbon allocation, stocks, residence times, and carbon use efficiency. Imposing observational constraints on the terrestrial carbon cycle

  5. Residence time distribution and hold-up in a cocurrent upflow packed bed reactor at elevated pressure

    NARCIS (Netherlands)

    van Gelder, Klaas B.; Westerterp, K.R.

    1990-01-01

    The residence time distribution in liquid phase was measured in a cocurrent upflow packed bed reactor for the system methanol-hydrogen at low Reynolds numbers and at elevated pressure. The plug flow with axial dispersion model was used to describe mixing in the system. The imperfect pulse method was

  6. Comparison of the tritium residence times of various ceramic breeder materials irradiated in EXOTIC experiments 4 and 5

    International Nuclear Information System (INIS)

    Kwast, H.; Elen, J.D.; Conrad, R.; Casadio, S.; Werle, H.; Verstappen, G.

    1990-09-01

    Tritium residence times have been determined for various ceramic tritium breeding materials from in-situ release measurements. The irradiations, codenamed EXOTIC (EXtraction Of Tritium In Ceramics), were carried out in the High Flux Reactor (HFR) Petten. During the irradiation more than 450 transients were performed and the corresponding tritium release measured. Materials supplied by SCK/CEN (Li 2 ZrO 3 ), CEA (Li 2 ZrO 3 and LiAlO 2 ), ENEA (LiAlO 2 ), KfK (Li 4 SiO 4 ), NRL (Li 6 Zr 2 O 7 ) and ECN (Li 8 ZrO 6 ) were irradiated in EXOTIC-5 to compare the tritium residence times obtained under equal conditions. Apart from differences in density, grain size, pore size and OPV it appeared that the tritium residence times of the lithium zirconates (pellets) were shorter than those of the Li 4 SiO 4 pebbles. The tritium residence times of the Li 4 SiO 4 pebbles were shorter than those of the LiAlO 2 pellets. (author). 7 refs.; 5 figs.; 3 tabs

  7. Hydraulic residence time and iron removal in a wetland receiving ferruginous mine water over a 4 year period from commissioning.

    Science.gov (United States)

    Kusin, F M; Jarvis, A P; Gandy, C J

    2010-01-01

    Analysis of residence time distribution (RTD) has been conducted for the UK Coal Authority's mine water treatment wetland at Lambley, Northumberland, to determine the hydraulic performance of the wetland over a period of approximately 4 years since site commissioning. The wetland RTD was evaluated in accordance with moment analysis and modelled based on a tanks-in-series (TIS) model to yield the hydraulic characteristics of system performance. Greater hydraulic performance was seen during the second site monitoring after 21 months of site operation i.e. longer hydraulic residence time to reflect overall system hydraulic efficiency, compared to wetland performance during its early operation. Further monitoring of residence time during the third year of wetland operation indicated a slight reduction in hydraulic residence time, thus a lower system hydraulic efficiency. In contrast, performance during the fourth year of wetland operation exhibited an improved overall system hydraulic efficiency, suggesting the influence of reed growth over the lifetime of such systems on hydraulic performance. Interestingly, the same pattern was found for iron (which is the primary pollutant of concern in ferruginous mine waters) removal efficiency of the wetland system from the second to fourth year of wetland operation. This may therefore, reflect the maturity of reeds for maintaining efficient flow distribution across the wetland to retain a longer residence time and significant fractions of water involved to enhance the extent of treatment received for iron attenuation. Further monitoring will be conducted to establish whether such performance is maintained, or whether efficiency decreases over time due to accumulation of dead plant material within the wetland cells.

  8. Residence time distributions of artificially infiltrated groundwater used for drinking water production

    Science.gov (United States)

    Popp, A. L.; Marçais, J.; Moeck, C.; Brennwald, M. S.; Kipfer, R.

    2017-12-01

    Public drinking water supply in urban areas is often challenging due to exposure to potential contamination and high water demands. At our study site, a drinking water supply field in Switzerland, managed aquifer recharge (MAR) was implemented to overcome an increasing water demand and decreasing water quality. Water from the river Rhine is put on a system of channels and ponds to artificially infiltrate and hence, increase the natural groundwater availability. The groundwater system consists of two overlying aquifers, with hydraulic connections related to fractures and faults. The deeper aquifer contains contaminants, which possibly originate from nearby landfills and industrial areas. The operating water works aims to pump recently infiltrated water only. However, we suspect that the pumped water contains a fraction of old water due to the fractured zones which serve as hydraulic connection between the two aquifers. With this study, we aim to better understand the mixing patterns between recently infiltrated water and old groundwater to evaluate the risk for contamination of the system. To reach our objective, we used a set of gas tracers (222Rn, 3H/3He, 4He) from fifteen wells distributed throughout the area to estimate the residence time distribution (RTD) of each well. We calibrated the RTD with a Binary Mixing Model, where the fraction of young groundwater is assumed to follow a Piston Flow Model. The older groundwater fraction is calibrated with a Dispersion Model. Our results reflect the heterogeneity of the system with some abstraction wells containing young water only and others showing an admixture of old water which can only be explained by a connection to the deeper aquifer. We also show that our results on calibrated RTDs are in accordance with other geochemical data such as electrical conductivity, major ions and pH. Our results will contribute to a sound conceptual flow and transport understanding and will help to optimize the water supply system.

  9. Carbon residence time dominates uncertainty in terrestrial vegetation responses to future climate and atmospheric CO2

    Science.gov (United States)

    Friend, Andrew D.; Lucht, Wolfgang; Rademacher, Tim T.; Keribin, Rozenn; Betts, Richard; Cadule, Patricia; Ciais, Philippe; Clark, Douglas B.; Dankers, Rutger; Falloon, Pete D.; Ito, Akihiko; Kahana, Ron; Kleidon, Axel; Lomas, Mark R.; Nishina, Kazuya; Ostberg, Sebastian; Pavlick, Ryan; Peylin, Philippe; Schaphoff, Sibyll; Vuichard, Nicolas; Warszawski, Lila; Wiltshire, Andy; Woodward, F. Ian

    2014-01-01

    Future climate change and increasing atmospheric CO2 are expected to cause major changes in vegetation structure and function over large fractions of the global land surface. Seven global vegetation models are used to analyze possible responses to future climate simulated by a range of general circulation models run under all four representative concentration pathway scenarios of changing concentrations of greenhouse gases. All 110 simulations predict an increase in global vegetation carbon to 2100, but with substantial variation between vegetation models. For example, at 4 °C of global land surface warming (510–758 ppm of CO2), vegetation carbon increases by 52–477 Pg C (224 Pg C mean), mainly due to CO2 fertilization of photosynthesis. Simulations agree on large regional increases across much of the boreal forest, western Amazonia, central Africa, western China, and southeast Asia, with reductions across southwestern North America, central South America, southern Mediterranean areas, southwestern Africa, and southwestern Australia. Four vegetation models display discontinuities across 4 °C of warming, indicating global thresholds in the balance of positive and negative influences on productivity and biomass. In contrast to previous global vegetation model studies, we emphasize the importance of uncertainties in projected changes in carbon residence times. We find, when all seven models are considered for one representative concentration pathway × general circulation model combination, such uncertainties explain 30% more variation in modeled vegetation carbon change than responses of net primary productivity alone, increasing to 151% for non-HYBRID4 models. A change in research priorities away from production and toward structural dynamics and demographic processes is recommended. PMID:24344265

  10. Firing technology in practice - temperature, residence time, corrosion; Feuerungstechnik in der Praxis - Temperatur, Verweilzeit, Korrosion

    Energy Technology Data Exchange (ETDEWEB)

    Freimann, P.; Holl, D. [Muellheizkraftwerk Betriebsgesellschaft mbH, Burgkirchen/Alz (Germany)

    1998-09-01

    In a circular dated 1st Sept. 1994, i.e., after the issue of the pertinent planning decision, the Federal Environmental Ministry, BMU, laid down uniform standards on measurements and the parameterisation of the evaluation system for different operation states and loads. Subsequently, TUeV, the German Technical Control Board, prepared the parameterisation curves on the basis of these specifications. The implementation of the BMU paper of 1st Sept. 1994 did not result in any advantage, nor did it lead to a reduction of plant emissions, nor to advantages in the operation of the waste-fuelled cogeneration plant. On the contrary, elevated gas consumption and operating trouble due to frequent feed stops worsened the operating state of the plant. Elevated crude gas temperature in the boiler reduced the lifetime of the two boilers to a critical degree. An operating temperature of 850 C and a residence time of approx. 1 sec. in Burgkirchen waste-fuelled cogeneration plant have not worsened emission values while rendering the plant operable again. [Deutsch] Durch Rundschreiben d. BMU vom 01.09.1994 - also nach Erlass des Planfeststellungsbeschlusses - wurden einheitliche Vorgaben ueber Messungen und Parametrierung des Auswertesystems fuer die verschiedenen Betriebs- bzw. Lastzustaende erlassen. Unter Beruecksichtigung dieser Vorgaben wurden vom TUeV die Parametrierungskurven erstellt. Die Umsetzung des BMU-Papieres vom 01.09.1994 ergab keinerlei Vorteile, weder gab es eine Verringerung der anlagenbedingten Emissionen noch Vorteile fuer den Betrieb des MHKW`s. Im Gegenteil, erhoehte Gasverbraeuche und Betriebsstoerungen durch oftmalige Beschickungsstops verschlechterten den Betriebszustand. Erhoehte Rohgastemperatur im Kessel reduzierten die Lebensdauer der beiden Kessel kritisch. Der Betrieb mit 850 C und mit einer Verweilzeit von ca. 1 sec. fuehrt im MHKW Burgkirchen zu keiner Verschlechterung der Emissionswerte, macht aber die Anlagen wieder betreibbar. (orig./SR)

  11. Groundwater residence time and paleohydrology in the Baltic Artesian basin:isotope geochemical data

    Science.gov (United States)

    Vaikmae, R.; Gerber, C.; Purtschert, R.; Aeschbach, W.; Raidla, V., Sr.; Lu, Z. T.; Zappala, J. C.; Mueller, P.; Mokrik, R., Sr.; Jiang, W.

    2016-12-01

    In this study of the Cambrian aquifer system(CAS) in the Baltic Artesian Basin(BAS) (, chemistry, stable isotopes, noble gas measurements, and dating tracers were combined for study the flow and recharge dynamics of the system over the last million years We find that the variability in chemical composition, stable isotopes and noble gas content in the basin is predominately controlled by mixing of three distinct water masses: Holocene and Pleistocene interglacial water, glacial meltwater, and brine. 81Kr is a nearly ideal dating tracer for such old systems. The radiogenic 4He and 40Ar provide additional information, but are more difficult to interpret in terms of groundwater age. In this study, we did not consider diffusive loss of 81Kr to stagnant water, which might result in an overestimation of groundwater ages ). However, the relatively high porosity and large thickness of the CAS, together with the presumed high salinity and low Kr content of the stagnant water all diminish the effect of diffusive 81Kr loss on age estimates. Our results confirm that under normal conditions, underground production of 81Kr is not affecting the dating results. 81Kr, 4He, and 40Ar all indicate a residence time of the brine of more than 1-3 Ma. Some uncertainty about the brine formation process remains, but the combination of chemical and stable isotope composition of the brine, noble gas concentrations and dating results favors evaporative enrichment of seawater. Tracer ages of interglacial water and glacial meltwater are on the order of several hundred thousand years, which means that several reversals of the flow direction in the CAS as a result of the paleoclimatology of the area have to be taken into account. Under such conditions, small vertical leakage, through fracture zones for example, might considerably impact the net flow pattern. Due to the cyclic flow direction reversals, the aquifer was probably in a transient state over most of the last 1 Ma period.

  12. A toolkit for groundwater mean residence time interpretation with gaseous tracers

    Science.gov (United States)

    Dávila, Pablo Fernando; Külls, Christoph; Weiler, Markus

    2013-12-01

    An analytical Excel-based toolkit called Gas-Tracer-Interpretation (GTI) was developed for determining mean residence time (MRT) of groundwater samples and for validating conceptual model assumptions. This novel data interpretation toolkit improves data handling during analysis and resolves some problems in the interpretation of data from environmental tracers. The toolkit can assist error detection, uncertainty and ambiguity during data analysis, particularly ambiguity due to the decline in atmospheric data of CFC input functions (air-mixing ratios of tracers). The innovative interpretation methodologies are: (1) corrections of environmental tracer data are conducted in concentrations in water instead of air (atmosphere), allowing comparison of different tracer input functions under similar conditions and thereby replacing the use of unique global atmospheric data; (2) a multi-model, multi-tracer approach is adopted to improve the number of different combinations of environmental tracers and lumped-parameter models (piston flow (PM), exponential (EM), exponential-piston flow (EPM), advection-dispersion (DM) and gamma (GM)); and (3) generation of sufficient information for determination of erroneous, unclear and ambiguous outcomes. Results are linked to graphical analysis to improve data view. GTI supports the environmental tracers CFC-11, CFC-12, CFC-113, SF6, 3H, and also SF5CF3, which is included as it represents a promising environmental tracer in hydrological research. The toolkit compares modeled input functions of tracers and data from samples. The apparent recharge age and MRT are estimated by combining explicit graphical and numerical data presentation. Due to the multi-model approach, it is possible to contrast selected models and estimate the best fit for a given sample, which is particularly useful for validating conceptual model assumptions. The toolkit has been developed in Microsoft ®Excel, and hence is user-friendly such that advanced programming

  13. Carbon residence time dominates uncertainty in terrestrial vegetation responses to future climate and atmospheric CO2.

    Science.gov (United States)

    Friend, Andrew D; Lucht, Wolfgang; Rademacher, Tim T; Keribin, Rozenn; Betts, Richard; Cadule, Patricia; Ciais, Philippe; Clark, Douglas B; Dankers, Rutger; Falloon, Pete D; Ito, Akihiko; Kahana, Ron; Kleidon, Axel; Lomas, Mark R; Nishina, Kazuya; Ostberg, Sebastian; Pavlick, Ryan; Peylin, Philippe; Schaphoff, Sibyll; Vuichard, Nicolas; Warszawski, Lila; Wiltshire, Andy; Woodward, F Ian

    2014-03-04

    Future climate change and increasing atmospheric CO2 are expected to cause major changes in vegetation structure and function over large fractions of the global land surface. Seven global vegetation models are used to analyze possible responses to future climate simulated by a range of general circulation models run under all four representative concentration pathway scenarios of changing concentrations of greenhouse gases. All 110 simulations predict an increase in global vegetation carbon to 2100, but with substantial variation between vegetation models. For example, at 4 °C of global land surface warming (510-758 ppm of CO2), vegetation carbon increases by 52-477 Pg C (224 Pg C mean), mainly due to CO2 fertilization of photosynthesis. Simulations agree on large regional increases across much of the boreal forest, western Amazonia, central Africa, western China, and southeast Asia, with reductions across southwestern North America, central South America, southern Mediterranean areas, southwestern Africa, and southwestern Australia. Four vegetation models display discontinuities across 4 °C of warming, indicating global thresholds in the balance of positive and negative influences on productivity and biomass. In contrast to previous global vegetation model studies, we emphasize the importance of uncertainties in projected changes in carbon residence times. We find, when all seven models are considered for one representative concentration pathway × general circulation model combination, such uncertainties explain 30% more variation in modeled vegetation carbon change than responses of net primary productivity alone, increasing to 151% for non-HYBRID4 models. A change in research priorities away from production and toward structural dynamics and demographic processes is recommended.

  14. Improving residents' handovers through just-in-time training for structured communication.

    Science.gov (United States)

    Rourke, Liam; Amin, Aditi; Boyington, Curtiss; Ao, Peter; Frolova, Natalia

    2016-01-01

    In a recent quality assurance project we learned that nearly half of the handovers we examined were characterized as unsatisfactory by our residents, who provided examples in which their anxiety had been piqued and patient care had been affected. These reports substantiated a growing body of literature on the relationship between the quality of handover and the quality of patient care, so we sought to improve the quality and consistency of the in-hosptial handovers undertaken by our internal medicine residents. Senior residents attended morning report for three consecutive month long blocks and evaluated the quality of the handovers using an observational protocol comprised of 16 aspects of effective handover. During the first block, the resident observed a median of eight of the 16 practices occurring across the 46 handovers, and a large amount of variability. At the beginning of the subsequent block we presented a concise introduction to a structured handover procedure (SBARR). The median quality of the subsequent 33 handovers rose to 11, and the variability decreased considerably. In the next block we refined the SBARR orientation to focus on the errors observed in the previous blocks, and the improvement in the quality and variability was sustained. The minor change, which requires few resources to sustain, had a favourable impact on the quality of our residents' in-hospital handovers.

  15. Structure-kinetic relationship studies of cannabinoid CB2receptor agonists reveal substituent-specific lipophilic effects on residence time.

    Science.gov (United States)

    Soethoudt, Marjolein; Hoorens, Mark W H; Doelman, Ward; Martella, Andrea; van der Stelt, Mario; Heitman, Laura H

    2018-03-21

    A decade ago, the drug-target residence time model has been (re-)introduced, which describes the importance of binding kinetics of ligands on their protein targets. Since then, it has been applied successfully for multiple protein targets, including GPCRs, for the development of lead compounds with slow dissociation kinetics (i.e. long target residence time) to increase in vivo efficacy or with short residence time to prevent on-target associated side effects. To date, this model has not been applied in the design and pharmacological evaluation of novel selective ligands for the cannabinoid CB 2 receptor (CB 2 R), a GPCR with therapeutic potential in the treatment of tissue injury and inflammatory diseases. Here, we have investigated the relationships between physicochemical properties, binding kinetics and functional activity in two different signal transduction pathways, G protein activation and β-arrestin recruitment. We synthesized 24 analogues of 3-cyclopropyl-1-(4-(6-((1,1-dioxidothiomorpholino)methyl)-5-fluoropyridin-2-yl)benzyl)imidazoleidine-2,4-dione (LEI101), our previously reported in vivo active and CB 2 R-selective agonist, with varying basicity and lipophilicity. We identified a positive correlation between target residence time and functional potency due to an increase in lipophilicity on the alkyl substituents, which was not the case for the amine substituents. Basicity of the agonists did not show a relationship with affinity, residence time or functional activity. Our findings provide important insights about the effects of physicochemical properties of the specific substituents of this scaffold on the binding kinetics of agonists and their CB 2 R pharmacology. This work therefore shows how CB 2 R agonists can be designed to have optimal kinetic profiles, which could aid the lead optimization process in drug discovery for the study or treatment of inflammatory diseases. Copyright © 2018 The Authors. Published by Elsevier Inc. All rights

  16. The Target Residence Time of Antihistamines Determines Their Antagonism of the G Protein-Coupled Histamine H1 Receptor

    Directory of Open Access Journals (Sweden)

    Reggie Bosma

    2017-09-01

    Full Text Available The pharmacodynamics of drug-candidates is often optimized by metrics that describe target binding (Kd or Ki value or target modulation (IC50. However, these metrics are determined at equilibrium conditions, and consequently information regarding the onset and offset of target engagement and modulation is lost. Drug-target residence time is a measure for the lifetime of the drug-target complex, which has recently been receiving considerable interest, as target residence time is shown to have prognostic value for the in vivo efficacy of several drugs. In this study, we have investigated the relation between the increased residence time of antihistamines at the histamine H1 receptor (H1R and the duration of effective target-inhibition by these antagonists. Hela cells, endogenously expressing low levels of the H1R, were incubated with a series of antihistamines and dissociation was initiated by washing away the unbound antihistamines. Using a calcium-sensitive fluorescent dye and a label free, dynamic mass redistribution based assay, functional recovery of the H1R responsiveness was measured by stimulating the cells with histamine over time, and the recovery was quantified as the receptor recovery time. Using these assays, we determined that the receptor recovery time for a set of antihistamines differed more than 40-fold and was highly correlated to their H1R residence times, as determined with competitive radioligand binding experiments to the H1R in a cell homogenate. Thus, the receptor recovery time is proposed as a cell-based and physiologically relevant metric for the lead optimization of G protein-coupled receptor antagonists, like the H1R antagonists. Both, label-free or real-time, classical signaling assays allow an efficient and physiologically relevant determination of kinetic properties of drug molecules.

  17. The Target Residence Time of Antihistamines Determines Their Antagonism of the G Protein-Coupled Histamine H1 Receptor

    Science.gov (United States)

    Bosma, Reggie; Witt, Gesa; Vaas, Lea A. I.; Josimovic, Ivana; Gribbon, Philip; Vischer, Henry F.; Gul, Sheraz; Leurs, Rob

    2017-01-01

    The pharmacodynamics of drug-candidates is often optimized by metrics that describe target binding (Kd or Ki value) or target modulation (IC50). However, these metrics are determined at equilibrium conditions, and consequently information regarding the onset and offset of target engagement and modulation is lost. Drug-target residence time is a measure for the lifetime of the drug-target complex, which has recently been receiving considerable interest, as target residence time is shown to have prognostic value for the in vivo efficacy of several drugs. In this study, we have investigated the relation between the increased residence time of antihistamines at the histamine H1 receptor (H1R) and the duration of effective target-inhibition by these antagonists. Hela cells, endogenously expressing low levels of the H1R, were incubated with a series of antihistamines and dissociation was initiated by washing away the unbound antihistamines. Using a calcium-sensitive fluorescent dye and a label free, dynamic mass redistribution based assay, functional recovery of the H1R responsiveness was measured by stimulating the cells with histamine over time, and the recovery was quantified as the receptor recovery time. Using these assays, we determined that the receptor recovery time for a set of antihistamines differed more than 40-fold and was highly correlated to their H1R residence times, as determined with competitive radioligand binding experiments to the H1R in a cell homogenate. Thus, the receptor recovery time is proposed as a cell-based and physiologically relevant metric for the lead optimization of G protein-coupled receptor antagonists, like the H1R antagonists. Both, label-free or real-time, classical signaling assays allow an efficient and physiologically relevant determination of kinetic properties of drug molecules. PMID:29033838

  18. The Target Residence Time of Antihistamines Determines Their Antagonism of the G Protein-Coupled Histamine H1 Receptor.

    Science.gov (United States)

    Bosma, Reggie; Witt, Gesa; Vaas, Lea A I; Josimovic, Ivana; Gribbon, Philip; Vischer, Henry F; Gul, Sheraz; Leurs, Rob

    2017-01-01

    The pharmacodynamics of drug-candidates is often optimized by metrics that describe target binding (K d or K i value) or target modulation (IC 50 ). However, these metrics are determined at equilibrium conditions, and consequently information regarding the onset and offset of target engagement and modulation is lost. Drug-target residence time is a measure for the lifetime of the drug-target complex, which has recently been receiving considerable interest, as target residence time is shown to have prognostic value for the in vivo efficacy of several drugs. In this study, we have investigated the relation between the increased residence time of antihistamines at the histamine H 1 receptor (H 1 R) and the duration of effective target-inhibition by these antagonists. Hela cells, endogenously expressing low levels of the H 1 R, were incubated with a series of antihistamines and dissociation was initiated by washing away the unbound antihistamines. Using a calcium-sensitive fluorescent dye and a label free, dynamic mass redistribution based assay, functional recovery of the H 1 R responsiveness was measured by stimulating the cells with histamine over time, and the recovery was quantified as the receptor recovery time . Using these assays, we determined that the receptor recovery time for a set of antihistamines differed more than 40-fold and was highly correlated to their H 1 R residence times, as determined with competitive radioligand binding experiments to the H 1 R in a cell homogenate. Thus, the receptor recovery time is proposed as a cell-based and physiologically relevant metric for the lead optimization of G protein-coupled receptor antagonists, like the H 1 R antagonists. Both, label-free or real-time, classical signaling assays allow an efficient and physiologically relevant determination of kinetic properties of drug molecules.

  19. Effect of diluents on soot precursor formation and temperature in ethylene laminar diffusion flames

    KAUST Repository

    Abhinavam Kailasanathan, Ranjith Kumar

    2013-03-01

    Soot precursor species concentrations and flame temperature were measured in a diluted laminar co-flow jet diffusion flame at pressures up to eight atmospheres while varying diluent type. The objective of this study was to gain a better understanding of soot production and oxidation mechanisms, which could potentially lead to a reduction in soot emissions from practical combustion devices. Gaseous samples were extracted from the centerline of an ethylene-air laminar diffusion flame, which was diluted individually with four diluents (argon, helium, nitrogen, and carbon dioxide) to manipulate flame temperature and transport properties. The diluted fuel and co-flow exit velocities (top-hat profiles) were matched at all pressures to minimize shear-layer effects, and the mass fluxes were fixed over the pressure range to maintain constant Reynolds number. The flame temperature was measured using a fine gauge R-type thermocouple at pressures up to four atmospheres. Centerline concentration profiles of major non-fuel hydrocarbons collected via extractive sampling with a quartz microprobe and quantification using GC/MS+FID are reported within. The measured hydrocarbon species concentrations are vary dramatically with pressure and diluent, with the helium and carbon dioxide diluted flames yielding the largest and smallest concentrations of soot precursors, respectively. In the case of C2H2 and C6H6, two key soot precursors, helium diluted flames had concentrations more than three times higher compared with the carbon dioxide diluted flame. The peak flame temperature vary with diluents tested, as expected, with carbon dioxide diluted flame being the coolest, with a peak temperature of 1760K at 1atm, and the helium diluted flame being the hottest, with a peak temperature of 2140K. At four atmospheres, the helium diluted flame increased to 2240K, but the CO2 flame temperature increased more, decreasing the difference to approximately 250K. © 2012 The Combustion Institute.

  20. Estimation of gastric residence time of the Heidelberg capsule in humans: effect of varying food composition

    International Nuclear Information System (INIS)

    Mojaverian, P.; Ferguson, R.K.; Vlasses, P.H.; Rocci, M.L. Jr.; Oren, A.; Fix, J.A.; Caldwell, L.J.; Gardner, C.

    1985-01-01

    In animal and human studies, the gastric emptying of large (greater than 1 mm) indigestible solids is due to the activity of the interdigestive migrating myoelectric complex. The gastric residence time (GRT) of an orally administered, nondigestible, pH-sensitive, radiotelemetric device (Heidelberg capsule) was evaluated in three studies in healthy volunteers. In 6 subjects, the GRT of the Heidelberg capsule was compared with the half-emptying time (t1/2) of diethylenetriaminepentaacetic acid labeled with technetium 99m after a 4-ml/kg liquid fatty meal. The mean (+/-SD) GRT (4.3 +/- 1.4 h) was significantly (p less than 0.001) longer than the mean t1/2 (1.1 +/- 0.3 h); the GRT was prolonged compared with the t1/2 in each subject. In a randomized, crossover trial in 10 subjects, frequent feeding caused a dramatic prolongation in mean GRT of the capsule compared with the fasting state (greater than 14.5 vs. 0.5 h, p less than 0.005). In another crossover study in 6 subjects, the GRT of the capsule was evaluated after an overnight fast, a standard breakfast including solid food, and a liquid meal (i.e., 200 ml of diluted light cream). The mean GRT was 2.6 +/- 0.9 h after the liquid meal vs. 1.2 +/- 0.8 h after fasting (p less than 0.025). The mean GRT after the breakfast was 4.8 +/- 1.5 h, which was significantly greater than that after fasting (p less than 0.001) and after the liquid meal (p less than 0.01). These data suggest that the GRT of the Heidelberg capsule is a marker of the interdigestive migrating myoelectric complex in humans, the interdigestive migrating myoelectric complex can be markedly delayed by frequent feedings with solids, and the interdigestive migrating myoelectric complex is delayed by both liquid and solid meals

  1. Estimation of gastric residence time of the Heidelberg capsule in humans: effect of varying food composition

    Energy Technology Data Exchange (ETDEWEB)

    Mojaverian, P.; Ferguson, R.K.; Vlasses, P.H.; Rocci, M.L. Jr.; Oren, A.; Fix, J.A.; Caldwell, L.J.; Gardner, C.

    1985-08-01

    In animal and human studies, the gastric emptying of large (greater than 1 mm) indigestible solids is due to the activity of the interdigestive migrating myoelectric complex. The gastric residence time (GRT) of an orally administered, nondigestible, pH-sensitive, radiotelemetric device (Heidelberg capsule) was evaluated in three studies in healthy volunteers. In 6 subjects, the GRT of the Heidelberg capsule was compared with the half-emptying time (t1/2) of diethylenetriaminepentaacetic acid labeled with technetium 99m after a 4-ml/kg liquid fatty meal. The mean (+/-SD) GRT (4.3 +/- 1.4 h) was significantly (p less than 0.001) longer than the mean t1/2 (1.1 +/- 0.3 h); the GRT was prolonged compared with the t1/2 in each subject. In a randomized, crossover trial in 10 subjects, frequent feeding caused a dramatic prolongation in mean GRT of the capsule compared with the fasting state (greater than 14.5 vs. 0.5 h, p less than 0.005). In another crossover study in 6 subjects, the GRT of the capsule was evaluated after an overnight fast, a standard breakfast including solid food, and a liquid meal (i.e., 200 ml of diluted light cream). The mean GRT was 2.6 +/- 0.9 h after the liquid meal vs. 1.2 +/- 0.8 h after fasting (p less than 0.025). The mean GRT after the breakfast was 4.8 +/- 1.5 h, which was significantly greater than that after fasting (p less than 0.001) and after the liquid meal (p less than 0.01). These data suggest that the GRT of the Heidelberg capsule is a marker of the interdigestive migrating myoelectric complex in humans, the interdigestive migrating myoelectric complex can be markedly delayed by frequent feedings with solids, and the interdigestive migrating myoelectric complex is delayed by both liquid and solid meals.

  2. Linking granulation performance with residence time and granulation liquid distributions in twin-screw granulation: An experimental investigation.

    Science.gov (United States)

    Kumar, Ashish; Alakarjula, Maija; Vanhoorne, Valérie; Toiviainen, Maunu; De Leersnyder, Fien; Vercruysse, Jurgen; Juuti, Mikko; Ketolainen, Jarkko; Vervaet, Chris; Remon, Jean Paul; Gernaey, Krist V; De Beer, Thomas; Nopens, Ingmar

    2016-07-30

    Twin-screw granulation is a promising wet granulation technique for the continuous manufacturing of pharmaceutical solid dosage forms. A twin screw granulator displays a short residence time. Thus, the solid-liquid mixing must be achieved quickly by appropriate arrangement of transport and kneading elements in the granulator screw allowing the production of granules with a size distribution appropriate for tableting. The distribution of residence time and granulation liquid is governed by the field conditions (such as location and length of mixing zones) in the twin-screw granulator, thus contain interesting information on granulation time, mixing and resulting sub-processes such as wetting, aggregation and breakage. In this study, the impact of process (feed rate, screw speed and liquid-to-solid ratio) and equipment parameters (number of kneading discs and stagger angle) on the residence time (distribution), the granulation liquid-powder mixing and the resulting granule size distributions during twin-screw granulation were investigated. Residence time and axial mixing data was extracted from tracer maps and the solid-liquid mixing was quantified from moisture maps, obtained by monitoring the granules at the granulator outlet using near infra-red chemical imaging (NIR-CI). The granule size distribution was measured using the sieving method. An increasing screw speed dominantly reduced the mean residence time. Interaction of material throughput with the screw speed and with the number of kneading discs led to most variation in the studied responses including residence time and mixing capacity. At a high screw speed, granulation yield improved due to high axial mixing. However, increasing material throughput quickly lowers the yield due to insufficient mixing of liquid and powder. Moreover, increasing liquid-to-solid ratio resulted in more oversized granules, and the fraction of oversized granules further increased at higher throughput. Although an increasing number

  3. Studies of propane flame soot acting as heterogeneous ice nuclei in conjunction with single particle soot photometer measurements

    Directory of Open Access Journals (Sweden)

    I. Crawford

    2011-09-01

    Full Text Available The ice nucleation efficiency of propane flame soot particles with and without a sulphuric acid coating was investigated using the aerosol and cloud chamber facility AIDA (Aerosol Interaction and Dynamics in the Atmosphere. The test soot for cloud formation simulations was produced using a propane flame Combustion Aerosol Standard generator (CAST, Jing-CAST Technologies. The organic carbon content (OC of the test soot was altered in a reproducible fashion by changing the fuel/air mixture of the generator. The soot content of ice nuclei was subsequently investigated using a combination of a pumped counterflow virtual impactor (PCVI to separate and evaporate the ice crystals, and a DMT single particle soot photometer (SP2 to examine the mixing state of the BC containing ice residuals.

    Ice nucleation was found to be most efficient for uncoated soot of low organic carbon content (~5 % organic carbon content where deposition freezing occurred at an ice saturation ratio Sice ~ 1.22 at a temperature T = 226.6 K with 25 % of the test soot becoming active as ice nuclei. Propane flame soot of higher organic carbon content (~30 % and ~70 % organic carbon content showed significantly lower ice nucleation efficiency (an activated fraction of the order of a few percent in the experiments than the low organic carbon content soot, with water saturation being required for freezing to occur. Ice nucleation occurred over the range Sice = 1.22–1.70, and T = 223.2–226.6 K. Analysis of the SP2 data showed that the 5 % organic carbon content soot had an undetectable OC coating whereas the 30 % organic carbon content soot had a thicker or less volatile OC coating.

    The application of a sulphuric acid coating to the flame soot shifted the threshold of the onset of freezing towards that of the homogeneous freezing of sulphuric acid; for the minimum OC flame soot this inhibited nucleation since the

  4. Influence of soot mixing state on aerosol light absorption and single scattering albedo during air mass aging at a polluted regional site in northeastern China

    Science.gov (United States)

    Cheng, Y. F.; Berghof, M.; Garland, R. M.; Wiedensohler, A.; Wehner, B.; Müller, T.; Su, H.; Zhang, Y. H.; Achtert, P.; Nowak, A.; PöSchl, U.; Zhu, T.; Hu, M.; Zeng, L. M.

    2009-01-01

    An aerosol optical closure study was performed using the observed high time- and size-resolved soot mixing states determined by a Volatility Tandem Differential Mobility Analyzer (VTDMA) at a polluted regional site, Yufa, in the south of Beijing during the summer of 2006. Good agreement was found between the simulated and measured aerosol absorption (σap, R = 0.9) and scattering (σsp, R ≥ 0.95). The soot mixing state at Yufa can be generally determined by VTDMA, in terms of properly predicting the σap using a simple optical model combined with spherical homogeneous and core-shell coated Mie codes. The possible uncertainties in the modeled σap were discussed. Rapid soot aging was observed, which led to large variations in the fractional contributions to σap by externally mixed and coated soot. On average, about 37% of the σap (˜10-60%) arose by the coated soot. The coating enhancement in σap and σsp of the coated soot can reach up to a factor of 8-10 within several hours owing to the secondary processing during daytime. It was contributed not only by the increased thickness of coating shell, but also the transition of soot from externally mixed to coated one. Hence, assuming constant soot mixing state for the regional climate model is not realistic and may lead to uncertainties. In the highly polluted region in northeastern China, the aerosol single scattering albedo may increase very fast owing to the rapid secondary particle formation and condensation (up to 0.90-0.95). This increase took place although the concurrent coating processing enhanced the light absorption capability of soot.

  5. Chemical composition profiles during alkaline flooding at different temperatures and extended residence times

    Energy Technology Data Exchange (ETDEWEB)

    Aflaki, R.; Handy, L.L.

    1992-12-01

    The objective of this work was to investigate whether or not caustic sweeps the major portion of the reservoir efficiently during an alkaline flood process. It was also the objective of this work to study the state of final equilibrium during a caustic flood through determination of the pH and chemical composition profiles along the porous medium. For this purpose, a long porous medium which provided extended residence times was required. It was necessary to set up the porous medium such that the changes in the pH and chemical composition of the solution could be monitored. Four Berea sandstone cores (8 in. length and1 in. diameter) placed in series provided the desired length and the opportunity for sampling in-between cores. This enabled establishment of pH and chemical composition profiles. The experiments were run at, temperatures up.to 180{degrees}C, and the flow rates varied from 4.8 to 0.2 ft/day. The samples were analyzed for pH and for Si and Al concentrations.The results show that caustic consumption is insignificant for temperatures up to 100{degrees}C. Above 100{degrees}C consumption increases and is accompanied by a significant decrease in pH. The sharp decline in pH also coincides with a sharp decline in concentration of silica in solution. The results also show that alumina is removed from the solution and solubility of alumina ultimately reaches zero. Sharp silica and pH declines take place even in the absence of any alumina in solution. As a result, removal of silica from solution is attributed to the irreversible caustic/rock interaction. This interaction is in the form of chemisorption reactions in which silica is adsorbed onto the rock surface consuming hydroxyl ion. Once these reactions were satisfied, caustic breakthrough occurs at a high pH. However, significant pore volumes of caustic must be injected for completion of the chemisorption.

  6. Chemical composition profiles during alkaline flooding at different temperatures and extended residence times

    Energy Technology Data Exchange (ETDEWEB)

    Aflaki, R.; Handy, L.L.

    1992-12-01

    The objective of this work was to investigate whether or not caustic sweeps the major portion of the reservoir efficiently during an alkaline flood process. It was also the objective of this work to study the state of final equilibrium during a caustic flood through determination of the pH and chemical composition profiles along the porous medium. For this purpose, a long porous medium which provided extended residence times was required. It was necessary to set up the porous medium such that the changes in the pH and chemical composition of the solution could be monitored. Four Berea sandstone cores (8 in. length and1 in. diameter) placed in series provided the desired length and the opportunity for sampling in-between cores. This enabled establishment of pH and chemical composition profiles. The experiments were run at, temperatures up.to 180[degrees]C, and the flow rates varied from 4.8 to 0.2 ft/day. The samples were analyzed for pH and for Si and Al concentrations.The results show that caustic consumption is insignificant for temperatures up to 100[degrees]C. Above 100[degrees]C consumption increases and is accompanied by a significant decrease in pH. The sharp decline in pH also coincides with a sharp decline in concentration of silica in solution. The results also show that alumina is removed from the solution and solubility of alumina ultimately reaches zero. Sharp silica and pH declines take place even in the absence of any alumina in solution. As a result, removal of silica from solution is attributed to the irreversible caustic/rock interaction. This interaction is in the form of chemisorption reactions in which silica is adsorbed onto the rock surface consuming hydroxyl ion. Once these reactions were satisfied, caustic breakthrough occurs at a high pH. However, significant pore volumes of caustic must be injected for completion of the chemisorption.

  7. Trait differences between naturalized and invasive plant species independent of residence time and phylogeny

    Science.gov (United States)

    Gallagher, R V; Randall, R P; Leishman, M R

    2015-01-01

    The ability to predict which alien plants will transition from naturalized to invasive prior to their introduction to novel regions is a key goal for conservation and has the potential to increase the efficacy of weed risk assessment (WRA). However, multiple factors contribute to plant invasion success (e.g., functional traits, range characteristics, residence time, phylogeny), and they all must be taken into account simultaneously in order to identify meaningful correlates of invasion success. We compiled 146 pairs of phylogenetically paired (congeneric) naturalized and invasive plant species in Australia with similar minimum residence times (i.e., time since introduction in years). These pairs were used to test for differences in 5 functional traits (flowering duration, leaf size, maximum height, specific leaf area [SLA], seed mass) and 3 characteristics of species’ native ranges (biome occupancy, mean annual temperature, and rainfall breadth) between naturalized and invasive species. Invasive species, on average, had larger SLA, longer flowering periods, and were taller than their congeneric naturalized relatives. Invaders also exhibited greater tolerance for different environmental conditions in the native range, where they occupied more biomes and a wider breadth of rainfall and temperature conditions than naturalized congeners. However, neither seed mass nor leaf size differed between pairs of naturalized and invasive species. A key finding was the role of SLA in distinguishing between naturalized and invasive pairs. Species with high SLA values were typically associated with faster growth rates, more rapid turnover of leaf material, and shorter lifespans than those species with low SLA. This suite of characteristics may contribute to the ability of a species to transition from naturalized to invasive across a wide range of environmental contexts and disturbance regimes. Our findings will help in the refinement of WRA protocols, and we advocate the

  8. Pole-to-Pole Distribution of Stratospheric Black Carbon (Soot) Aerosol from Aircraft

    Science.gov (United States)

    Pueschel, R. F.; Ferry, G. V.; Verma, S.; Howard, S. D.; Strawa, Anthony W. (Technical Monitor)

    1995-01-01

    The distribution of black carbon (soot) aerosol (BCA) in the atmosphere is of interest for several reasons: (1) Because BCA has the highest absorption cross section of any compound known, it can absorb solar radiation to cause atmospheric warming. (2) Because it is a strong adsorber of gases, it can catalyze heterogeneous reactions to change the chemical composition of the atmosphere.(3) If aircraft are a major source of BCA, it is an important tracer of aircraft emissions. Analysis for BCA of impactor samples from Arctic and Antarctic deployments, utilizing particle morphology of scanning electron microscopy images, permits the following conclusions: (1) The BCA concentration in the northern stratosphere varies between 0 and 2.6 ng m-3 averaging 0.6 ng/cu m. (2) This BCA loading is commensurate with estimated fuel consumptions in the stratosphere by the current commercial fleet and an emission index E=0.03 g BCA per kg fuel burnt which was measured in jet exhaust at al titude.Thus, most stratospheric BCA in the northern stratosphere results from aircraft emissions. The background BCA concentration in the southern stratosphere varies between 0 and 0.6 ng cu m averaging 0.1 ng/cu m. This strong meridional gradient implies that stratospheric BCA residence time- is shorter than are mixing times between hemispheres. Projected annual fuel consumption of a future supersonic commercial fleet is 7E13 g. This fleet would increase stratospheric BCA loadings by a factor of 2-3, because almost all fuel would be burnt above the tropopause. An improved EI(BCA) by a factor of ten would result in an increase of stratospheric BCA loadings by approximately 50 %.

  9. Investigation of soot morphology and particle size distrib ution in a turbulent nonpremixed flame via Monte Carlo simulations

    KAUST Repository

    Abdelgadir, Ahmed

    2015-03-30

    Recently, our group performed a set of direct numerical simulations (DNS) of soot formation and growth in a n-heptane three dimensional non-premixed jet flame [Attili et al., Proc. Comb. Inst, 35, 2015], [Attili et al., Comb. Flame, 161, 2014], [Bisetti et al.,Trans of the Royal Soc, 372, 2014]. The evolution of species relevant to soot formation and growth have been sampled along a large number of Lagrangian trajectories in the DNS. In this work, the DNS results are post-processed to compute the soot evolution along selected Lagrangian trajectories using a Monte Carlo method. An operator splitting approach is adopted to split the deterministic processes (nucleation, surface growth and oxidation) from coagulation, which is treated stochastically. The morphological properties of soot and the particlesize distribution are investigated. For trajectories that experience an early strong nucleation event, the particle size distribution is found to be bimodal, as the soot particles have enough time to coagulate and grow while it is unimodal for trajectories characterized by only late nucleation events. As a results, the average size distribution at two different crosswise positions in the flame is unimodal.

  10. Fast Pyrolysis Behavior of Banagrass as a Function of Temperature and Volatiles Residence Time in a Fluidized Bed Reactor.

    Science.gov (United States)

    Morgan, Trevor James; Turn, Scott Q; George, Anthe

    2015-01-01

    A reactor was designed and commissioned to study the fast pyrolysis behavior of banagrass as a function of temperature and volatiles residence time. Four temperatures between 400 and 600°C were examined as well as four residence times between ~1.0 and 10 seconds. Pyrolysis product distributions of bio-oil, char and permanent gases were determined at each reaction condition. The elemental composition of the bio-oils and chars was also assessed. The greatest bio-oil yield was recorded when working at 450°C with a volatiles residence time of 1.4 s, ~37 wt% relative to the dry ash free feedstock (excluding pyrolysis water). The amounts of char (organic fraction) and permanent gases under these conditions are ~4 wt% and 8 wt% respectively. The bio-oil yield stated above is for 'dry' bio-oil after rotary evaporation to remove solvent, which results in volatiles and pyrolysis water being removed from the bio-oil. The material removed during drying accounts for the remainder of the pyrolysis products. The 'dry' bio-oil produced under these conditions contains ~56 wt% carbon which is ~40 wt% of the carbon present in the feedstock. The oxygen content of the 450°C, 1.4 s 'dry' bio-oil is ~38 wt%, which accounts for ~33 wt% of the oxygen in the feedstock. At higher temperature or longer residence time less bio-oil and char is recovered and more gas and light volatiles are produced. Increasing the temperature has a more significant effect on product yields and composition than increasing the volatiles residence time. At 600°C and a volatiles residence time of 1.2 seconds the bio-oil yield is ~21 wt% of the daf feedstock, with a carbon content of 64 wt% of the bio-oil. The bio-oil yield from banagrass is significantly lower than from woody biomass or grasses such as switchgrass or miscanthus, but is similar to barley straw. The reason for the low bio-oil yield from banagrass is thought to be related to its high ash content (8.5 wt% dry basis) and high concentration of alkali

  11. Fast Pyrolysis Behavior of Banagrass as a Function of Temperature and Volatiles Residence Time in a Fluidized Bed Reactor.

    Directory of Open Access Journals (Sweden)

    Trevor James Morgan

    Full Text Available A reactor was designed and commissioned to study the fast pyrolysis behavior of banagrass as a function of temperature and volatiles residence time. Four temperatures between 400 and 600°C were examined as well as four residence times between ~1.0 and 10 seconds. Pyrolysis product distributions of bio-oil, char and permanent gases were determined at each reaction condition. The elemental composition of the bio-oils and chars was also assessed. The greatest bio-oil yield was recorded when working at 450°C with a volatiles residence time of 1.4 s, ~37 wt% relative to the dry ash free feedstock (excluding pyrolysis water. The amounts of char (organic fraction and permanent gases under these conditions are ~4 wt% and 8 wt% respectively. The bio-oil yield stated above is for 'dry' bio-oil after rotary evaporation to remove solvent, which results in volatiles and pyrolysis water being removed from the bio-oil. The material removed during drying accounts for the remainder of the pyrolysis products. The 'dry' bio-oil produced under these conditions contains ~56 wt% carbon which is ~40 wt% of the carbon present in the feedstock. The oxygen content of the 450°C, 1.4 s 'dry' bio-oil is ~38 wt%, which accounts for ~33 wt% of the oxygen in the feedstock. At higher temperature or longer residence time less bio-oil and char is recovered and more gas and light volatiles are produced. Increasing the temperature has a more significant effect on product yields and composition than increasing the volatiles residence time. At 600°C and a volatiles residence time of 1.2 seconds the bio-oil yield is ~21 wt% of the daf feedstock, with a carbon content of 64 wt% of the bio-oil. The bio-oil yield from banagrass is significantly lower than from woody biomass or grasses such as switchgrass or miscanthus, but is similar to barley straw. The reason for the low bio-oil yield from banagrass is thought to be related to its high ash content (8.5 wt% dry basis and high

  12. Fast Pyrolysis Behavior of Banagrass as a Function of Temperature and Volatiles Residence Time in a Fluidized Bed Reactor

    Science.gov (United States)

    Morgan, Trevor James; Turn, Scott Q.; George, Anthe

    2015-01-01

    A reactor was designed and commissioned to study the fast pyrolysis behavior of banagrass as a function of temperature and volatiles residence time. Four temperatures between 400 and 600°C were examined as well as four residence times between ~1.0 and 10 seconds. Pyrolysis product distributions of bio-oil, char and permanent gases were determined at each reaction condition. The elemental composition of the bio-oils and chars was also assessed. The greatest bio-oil yield was recorded when working at 450°C with a volatiles residence time of 1.4 s, ~37 wt% relative to the dry ash free feedstock (excluding pyrolysis water). The amounts of char (organic fraction) and permanent gases under these conditions are ~4 wt% and 8 wt% respectively. The bio-oil yield stated above is for 'dry' bio-oil after rotary evaporation to remove solvent, which results in volatiles and pyrolysis water being removed from the bio-oil. The material removed during drying accounts for the remainder of the pyrolysis products. The 'dry' bio-oil produced under these conditions contains ~56 wt% carbon which is ~40 wt% of the carbon present in the feedstock. The oxygen content of the 450°C, 1.4 s 'dry' bio-oil is ~38 wt%, which accounts for ~33 wt% of the oxygen in the feedstock. At higher temperature or longer residence time less bio-oil and char is recovered and more gas and light volatiles are produced. Increasing the temperature has a more significant effect on product yields and composition than increasing the volatiles residence time. At 600°C and a volatiles residence time of 1.2 seconds the bio-oil yield is ~21 wt% of the daf feedstock, with a carbon content of 64 wt% of the bio-oil. The bio-oil yield from banagrass is significantly lower than from woody biomass or grasses such as switchgrass or miscanthus, but is similar to barley straw. The reason for the low bio-oil yield from banagrass is thought to be related to its high ash content (8.5 wt% dry basis) and high concentration of alkali

  13. Time-motion studies of internal medicine residents' duty hours: a systematic review and meta-analysis

    Directory of Open Access Journals (Sweden)

    Leafloor CW

    2015-11-01

    Full Text Available Cameron W Leafloor,1 Heather A Lochnan,2,3,6 Catherine Code,2,4 Erin J Keely,2,3,6 Deanna M Rothwell,5,6 Alan J Forster,2,4–6 Allen R Huang2,6,7 1Faculty of Medicine, 2Department of Medicine, 3Division of Endocrinology and Metabolism, 4Division of General Internal Medicine, 5Performance Measurement and Innovation, 6Ottawa Hospital Research Institute, 7Division of Geriatric Medicine, The Ottawa Hospital and University of Ottawa, Ottawa, ON, Canada Background: Since the mid-1980s, medical residents' long duty hours have been under scrutiny as a factor affecting patient safety and the work environment for the residents. After several mandated changes in duty hours, it is important to understand how residents spend their time before proposing and implementing future changes. Time-motion methodology may provide reliable information on what residents do while on duty.Purpose: The purpose of this study is to review all available literature pertaining to time-motion studies of internal medicine residents while on a medicine service and to understand how much of their time is apportioned to various categories of tasks, and also to determine the effects of the Accreditation Council for Graduate Medical Education (ACGME-mandated duty hour changes on resident workflow in North America.Methods: Electronic bibliographic databases were searched for articles in English between 1941 and April 2013 reporting time-motion studies of internal medicine residents rotating through a general medicine service.Results: Eight articles were included. Residents spent 41.8% of time in patient care activities, 18.1% communicating, 13.8% in educational activities, 19.7% in personal/other, and 6.6% in transit. North American data showed the following changes after the implementation of the ACGME 2003 duty hours standard: patient care activities from 41.8% to 40.8%, communication activities from 19.0% to 22.3%, educational activities from 17.7% to 11.6%, and personal

  14. Geochemical modelling of groundwater evolution and residence time at the Kivetty site

    Energy Technology Data Exchange (ETDEWEB)

    Pitkaenen, P.; Luukkonen, A. [VTT Communities and Infrastructure, Espoo (Finland); Ruotsalainen, P. [Fintact Oy, Helsinki (Finland); Leino-Forsman, H.; Vuorinen, U. [VTT Chemical Technology, Espoo (Finland)

    1998-12-01

    groundwater are due to carbonate reactions: oxidising of organic carbon, and dissolution and precipitation of calcite. The carbonate reactions and slight hydrolysis of silicates stabilise the pH value at 8-9. In addition to aerobic oxidation of organic matter, oxidative dissolution of biotite seems to be an important oxygen consumer at shallow depth during recharge. The most important process controlling the redox state deeper in the bedrock was interpreted to be the microbially mediated sulphate reduction with simultaneous anaerobic respiration of organic carbon. This process buffers the redox level of about -200 - -300 mV depending on the pH. Even though the salinities of the groundwater samples and mass-transfer along flow paths remain low, the geochemical evolution was fully developed and has reached quite a stable thermodynamic state. The residence times of the groundwater samples cover the time span back to glaciation. Young ages seem to be limited to the upper part of bedrock, and any really dynamic natural flowpath with deep observed recently recharged water cannot be demonstrated. Deglacial or subglacial ages (over 9,700 years old at Kivetty) are typical below the 150-300m level in the bedrock. Subglacial waters are interpreted to derive from mixing of preglacial water and meltwater, the input of which is estimated to be about 20% at the most. Indications of elevated oxygen intrusion cannot be observed in groundwater having glacial signals. (orig.) 122 refs.

  15. Camphor soot: a tunable light emitter

    Science.gov (United States)

    Swapna, M. S.; Saritha Devi, H. V.; Sankararaman, S.

    2018-01-01

    The work in this paper is the first report on the green synthesis of the blue light emitter from waxy, flammable solid collected from Cinnamomum camphora by controlled combustion for photonic applications. Analysis with field emission scanning electron microscope and high-resolution transmission electron microscope provides the morphology, whereas the thermogravimetric analysis gives the thermal stability of the soot. The optical and structural characterizations are done by recording UV-Visible, Photoluminescent, and Raman Spectrum. The CIE plot and the power spectrum of the sample show a blue emission at an excitation of 350 nm at room temperature with a quantum yield of 46.15%. The dependence of luminescent behavior on temperature and excitation wavelength reveals that the material is a tunable blue emitter. This green synthesis of the blue light emitter is highly significant, when the world is in search of a simple, phosphor-free, non-toxic, cost-effective material with good quantum efficiency.

  16. Visualizing the mobility of silver during catalytic soot oxidation

    DEFF Research Database (Denmark)

    Gardini, Diego; Christensen, Jakob M.; Damsgaard, Christian Danvad

    2016-01-01

    The catalytic activity and mobility of silver nanoparticles used as catalysts in temperature programmed oxidation of soot:silver (1:5 wt:wt) mixtures have been investigated by means of flow reactor experiments and in situ environmental transmission electron microscopy (ETEM). The carbon oxidation...... temperature was significantly lower compared to uncatalyzed soot oxidation with soot and silver loosely stirred together (loose contact) and lowered further with the two components crushed together (tight contact). The in situ TEM investigations revealed that the silver particles exhibited significant...

  17. Towards predictive simulations of soot formation: from surrogate to turbulence

    Energy Technology Data Exchange (ETDEWEB)

    Blanquart, Guillaume [California Inst. of Technology (CalTech), Pasadena, CA (United States)

    2017-03-28

    The combustion of transportation fuels leads to the formation of several kinds of pollutants, among which are soot particles. These particles, also formed during coal combustion and in fires, are the source of several health problems and environmental issues. Unfortunately, our current understanding of the chemical and physical phenomena leading to the formation of soot particles remains incomplete, and as a result, the predictive capability of our numerical tools is lacking. The objective of the work was to reduce the gap in the present understanding and modeling of soot formation both in laminar and turbulent flames. The effort spanned several length scales from the molecular level to large scale turbulent transport.

  18. Caregiver Person-Centeredness and Behavioral Symptoms in Nursing Home Residents With Dementia: A Timed-Event Sequential Analysis.

    Science.gov (United States)

    Gilmore-Bykovskyi, Andrea L; Roberts, Tonya J; Bowers, Barbara J; Brown, Roger L

    2015-06-01

    Evidence suggests that person-centered caregiving approaches may reduce dementia-related behavioral symptoms; however, little is known about the sequential and temporal associations between specific caregiver actions and behavioral symptoms. The aim of this study was to identify sequential associations between caregiver person-centered actions, task-centered actions, and resident behavioral symptoms and the temporal variation within these associations. Videorecorded observations of naturally occurring interactions (N = 33; 724min) between 12 nursing home (NH) residents with dementia and eight certified nursing assistants were coded for caregiver person-centered actions, task-centered actions, and resident behavioral symptoms and analyzed using timed-event sequential analysis. Although caregiver actions were predominantly person-centered, we found that resident behavioral symptoms were significantly more likely to occur following task-centered caregiver actions than person-centered actions. Findings suggest that the person-centeredness of caregivers is sequentially and temporally related to behavioral symptoms in individuals with dementia. Additional research examining the temporal structure of these relationships may offer valuable insights into the utility of caregiver person-centeredness as a low-cost strategy for improving behavioral symptom management in the NH setting. © The Author 2015. Published by Oxford University Press on behalf of The Gerontological Society of America. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

  19. Increasing functional modularity with residence time in the co-distribution of native and introduced vascular plants.

    Science.gov (United States)

    Hui, Cang; Richardson, David M; Pyšek, Petr; Le Roux, Johannes J; Kučera, Tomáš; Jarošík, Vojtěch

    2013-01-01

    Species gain membership of regional assemblages by passing through multiple ecological and environmental filters. To capture the potential trajectory of structural changes in regional meta-communities driven by biological invasions, one can categorize species pools into assemblages of different residence times. Older assemblages, having passed through more environmental filters, should become more functionally ordered and structured. Here we calculate the level of compartmentalization (modularity) for three different-aged assemblages (neophytes, introduced after 1500 AD; archaeophytes, introduced before 1500 AD, and natives), including 2,054 species of vascular plants in 302 reserves in central Europe. Older assemblages are more compartmentalized than younger ones, with species composition, phylogenetic structure and habitat characteristics of the modules becoming increasingly distinctive. This sheds light on two mechanisms of how alien species are functionally incorporated into regional species pools: the settling-down hypothesis of diminishing stochasticity with residence time, and the niche-mosaic hypothesis of inlaid neutral modules in regional meta-communities.

  20. Isotopic and geochemical tracers in the evaluation of groundwater residence time and salinization problems at Santiago Island, Cape Verde

    Energy Technology Data Exchange (ETDEWEB)

    Carreira, Paula M.; Nunes, Dina [Quimica Analitica e Ambiental, IST/ITN, Universidade Tecnica de Lisboa, Estrada Nacional no. 10, 2686-953 Sacavem (Portugal); Marques, Jose M. [Centro de Petrologia e Geoquimica. Instituto Superior Tecnico, UTL, Av. Rovisco Pais, 1049-001 Lisboa (Portugal); Monteiro Santos, Fernando A. [Universidade de Lisboa-IDL, 1749-016 Lisboa (Portugal); Goncalves, Rui [Inst. Politecnico de Tomar, Quinta do Contador, Estrada da Serra, 2300 Tomar (Portugal); Pina, Antonio; Mota Gomes, Antonio [Instituto Superior de Educacao, Praia, Santiago (Cape Verde)

    2013-07-01

    Stable isotopes (δ{sup 18}O, δ{sup 2}H) and tritium ({sup 3}H), together with geochemistry and geophysical data, were used for evaluating groundwater recharge sources, flow paths, and residence times in a watershed on Santiago Island, Cape Verde, West Africa. Stable isotopes indicate the predominance of high-elevation precipitation that undergoes little evaporation prior to groundwater recharge. Low tritium concentrations at seven sampling sites indicate groundwater residence times greater than 50 years. Higher tritium values at other locations suggest more recent recharge. Young ages indicate local recharge and potential groundwater vulnerability to surface contamination and/or salt-water intrusion. Geochemical results indicate that water-rock interaction mechanisms are the major processes responsible for the groundwater quality (mainly calcium-bicarbonate type), reflecting the lithological composition of subsurface soil. (authors)

  1. Optimization of Drug Delivery Systems for Intraperitoneal Therapy to Extend the Residence Time of the Chemotherapeutic Agent

    Directory of Open Access Journals (Sweden)

    L. De Smet

    2013-01-01

    Full Text Available Intraperitoneal (IP chemotherapy is an effective way of treating peritoneal carcinomatosis of colorectal origin after complete cytoreduction. Although IP therapy has been already performed for many years, no standardized treatment design has been developed in terms of schedule, residence time, drug, or carrier solution. Because of the fast clearance of the conventional intravenous (IV drug delivery systems used for IP therapy, a lot of research is performed to optimize IP drug delivery and extend the residence time of the cytotoxic agent in the peritoneal cavity. This paper reviews the recent advances made in drug delivery systems for IP chemotherapy, discussing the use of microparticles, nanoparticles, liposomes, micelles, implants, and injectable depots for IP delivery.

  2. Measurement of residence time distribution of liquid phase in an industrial-scale continuous pulp digester using radiotracer technique.

    Science.gov (United States)

    Sheoran, Meenakshi; Goswami, Sunil; Pant, Harish J; Biswal, Jayashree; Sharma, Vijay K; Chandra, Avinash; Bhunia, Haripada; Bajpai, Pramod K; Rao, S Madhukar; Dash, A

    2016-05-01

    A series of radiotracer experiments was carried out to measure residence time distribution (RTD) of liquid phase (alkali) in an industrial-scale continuous pulp digester in a paper industry in India. Bromine-82 as ammonium bromide was used as a radiotracer. Experiments were carried out at different biomass and white liquor flow rates. The measured RTD data were treated and mean residence times in individual digester tubes as well in the whole digester were determined. The RTD was also analyzed to identify flow abnormalities and investigate flow dynamics of the liquid phase in the pulp digester. Flow channeling was observed in the first section (tube 1) of the digester. Both axial dispersion and tanks-in-series with backmixing models preceded with a plug flow component were used to simulate the measured RTD and quantify the degree of axial mixing. Based on the study, optimum conditions for operating the digester were proposed. Copyright © 2016 Elsevier Ltd. All rights reserved.

  3. Isotopic and geochemical tracers in the evaluation of groundwater residence time and salinization problems at Santiago Island, Cape Verde

    International Nuclear Information System (INIS)

    Carreira, Paula M.; Nunes, Dina; Marques, Jose M.; Monteiro Santos, Fernando A.; Goncalves, Rui; Pina, Antonio; Mota Gomes, Antonio

    2013-01-01

    Stable isotopes (δ 18 O, δ 2 H) and tritium ( 3 H), together with geochemistry and geophysical data, were used for evaluating groundwater recharge sources, flow paths, and residence times in a watershed on Santiago Island, Cape Verde, West Africa. Stable isotopes indicate the predominance of high-elevation precipitation that undergoes little evaporation prior to groundwater recharge. Low tritium concentrations at seven sampling sites indicate groundwater residence times greater than 50 years. Higher tritium values at other locations suggest more recent recharge. Young ages indicate local recharge and potential groundwater vulnerability to surface contamination and/or salt-water intrusion. Geochemical results indicate that water-rock interaction mechanisms are the major processes responsible for the groundwater quality (mainly calcium-bicarbonate type), reflecting the lithological composition of subsurface soil. (authors)

  4. The distribution of range sizes of native and alien plants in four European countries and the effects of residence time

    Czech Academy of Sciences Publication Activity Database

    Williamson, M.; Dehnen-Schmutz, K.; Kühn, I.; Hill, M.; Klotz, S.; Milbau, A.; Stout, J.; Pyšek, Petr

    2009-01-01

    Roč. 15, č. 1 (2009), s. 158-166 ISSN 1366-9516 R&D Projects: GA MŠk LC06073 Grant - others:Evropská komise(XE) SSPI-CT-2003-511202 Institutional research plan: CEZ:AV0Z60050516 Keywords : invasions * distribution range * residence time Subject RIV: EF - Botanics Impact factor: 4.224, year: 2009

  5. Regional oxygen reduction and denitrification rates in groundwater from multi-model residence time distributions, San Joaquin Valley, USA

    Science.gov (United States)

    Green, Christopher T.; Jurgens, Bryant; Zhang, Yong; Starn, Jeffrey; Singleton, Michael J.; Esser, Bradley K.

    2016-01-01

    Rates of oxygen and nitrate reduction are key factors in determining the chemical evolution of groundwater. Little is known about how these rates vary and covary in regional groundwater settings, as few studies have focused on regional datasets with multiple tracers and methods of analysis that account for effects of mixed residence times on apparent reaction rates. This study provides insight into the characteristics of residence times and rates of O2 reduction and denitrification (NO3− reduction) by comparing reaction rates using multi-model analytical residence time distributions (RTDs) applied to a data set of atmospheric tracers of groundwater age and geochemical data from 141 well samples in the Central Eastern San Joaquin Valley, CA. The RTD approach accounts for mixtures of residence times in a single sample to provide estimates of in-situ rates. Tracers included SF6, CFCs, 3H, He from 3H (tritiogenic He),14C, and terrigenic He. Parameter estimation and multi-model averaging were used to establish RTDs with lower error variances than those produced by individual RTD models. The set of multi-model RTDs was used in combination with NO3− and dissolved gas data to estimate zero order and first order rates of O2 reduction and denitrification. Results indicated that O2 reduction and denitrification rates followed approximately log-normal distributions. Rates of O2 and NO3− reduction were correlated and, on an electron milliequivalent basis, denitrification rates tended to exceed O2 reduction rates. Estimated historical NO3− trends were similar to historical measurements. Results show that the multi-model approach can improve estimation of age distributions, and that relatively easily measured O2 rates can provide information about trends in denitrification rates, which are more difficult to estimate.

  6. Successful invaders co-opt pollinators of native flora and accumulate insect pollinators with increasing residence time

    Czech Academy of Sciences Publication Activity Database

    Pyšek, Petr; Jarošík, Vojtěch; Chytrý, M.; Danihelka, Jiří; Kuhn, D.; Pergl, Jan; Tichý, L.; Biesmeijer, J. C.; Ellis, W. N.; Kunin, W. E.; Settele, J.

    2011-01-01

    Roč. 81, č. 2 (2011), s. 277-293 ISSN 0012-9615 R&D Projects: GA MŠk LC06073; GA ČR GA206/09/0563 Grant - others:European Comission(XE) GOCE-CT-2003-506675 Institutional research plan: CEZ:AV0Z60050516 Keywords : pollination * residence time * plant invasion Subject RIV: EF - Botanics Impact factor: 7.433, year: 2011

  7. Comparison of Residence Time Distributions of Liquid for Different Types of Input Signal Using a Stimulus-Response Technique

    Czech Academy of Sciences Publication Activity Database

    Čermáková, Jiřina; Siyakatshana, N.; Šilar, F.; Kudrna, V.; Jahoda, M.; Machoň, V.

    2003-01-01

    Roč. 57, č. 6 (2003), s. 427-431 ISSN 0366-6352. [International Conference of Slovak Society of Chemical Engineering /30./. Tatranské Matliare, 26.05.2003-30.05.2003] Institutional research plan: CEZ:AV0Z4072921 Keywords : stirred tank * stimulus-response technique * residence time distribution Subject RIV: CF - Physical ; Theoretical Chemistry Impact factor: 0.226, year: 2003

  8. Characterization and reactivity of soot from fast pyrolysis of lignocellulosic compounds and monolignols

    DEFF Research Database (Denmark)

    Trubetskaya, Anna; Brown, Avery; Tompsett, Geoffrey

    2018-01-01

    This study presents the effect of lignocellulosic compounds and monolignols on the yield, nanostructure and reactivity of soot generated at 1250 °C in a drop tube furnace. The structure of soot was characterized by electron microscopy techniques, Raman spectroscopy and electron spin resonance spe...... of the extraction solvent had a strong influence on the soot reactivity. The Soxhlet extraction of softwood and wheat straw lignin soot using methanol decreased the soot reactivity, whereas acetone extraction had only a modest effect....

  9. A multitracer approach to estimate groundwater residence time distributions at a managed aquifer recharge site

    Science.gov (United States)

    Popp, Andrea; Kipfer, Rolf

    2017-04-01

    Managed aquifer recharge (MAR) has become a common water management tool and serves various purposes such as improving the quality of groundwater (GW). At the study site, the Hardwald in Muttenz (Switzerland), MAR has been implemented in the mid-1950s to overcome increasing water demands. GW is artificially recharged with water from the river Rhine through a system of channels and ponds. The area is surrounded by potential contamination sites such as chemical industry, former landfills, a highway and a freight depot. Furthermore, the area shows a complex hydrogeologic setting with several fault zones and two main aquifers, the Quaternary Rhine gravel aquifer overlying a karstified Upper Muschelkalk limestone aquifer. Water from the deeper limestone aquifer is suspected to contain contaminants originating from the landfills. The fractures might serve as a hydraulic connection between the upper and lower aquifer. Further, groundwater pumping might enhance the mixing of recently infiltrated water with older water from the lower aquifer. Hence, the proximity to potential contamination sites and the complex geologic setting both pose risks for GW pollution and challenge the drinking water production in this area. To guarantee a safe drinking water supply, it is crucial to know the mixing patterns of young and old GW abstracted from the pumping wells. With this study we aim to determine the spatial variability of GW residence time distributions to differentiate between recently infiltrated river water and older groundwater. To reach our objectives, we use a combination of the following tracers to cover a wide range of possible GW ages: (1) radiogenic 222Rn (young water := <3 weeks); (2) tritium (3H) in combination with its tritiogenic decay product 3He (old water := 0.5-50 years); and (3) radiogenic 4He (very old water := 100-1000 years). Additionally, we analysed other dissolved (noble) gases (O2, N2, Ar, Kr) to estimate the amount of excess air and to derive the

  10. Geochemical modelling of groundwater evolution and residence time at the Olkiluoto site

    International Nuclear Information System (INIS)

    Pitkaenen, P.; Luukkonen, A.; Ruotsalainen, P.; Leino-Forsman, H.; Vuorinen, U.

    1999-05-01

    external conditions such as glaciation, palaeo Baltic stages, land uplift and ancient hydrothermal events, have had a significant effect on local palaeohydrogeological conditions. They have caused great variability, which is observable in the chemical data notably in salinity (up to 70 g/l), water type and contents of conservative parameters, such as Cl, Br and stable isotopes of water. However, their influence is also significant on the water-rock interaction that principally controls the pH and redox conditions - varying 7.5 to 8 and -200 to -300 mV, respectively - in the groundwater, although the calculated mass transfer in the reactions is minor compared with conservative mixing at the site. Calcite in fractures is interpreted to principally control pH level in groundwater. Sulphidic redox conditions dominate in the upper 500 m in brackish and slightly saline groundwater. Deeper sulphur species are absent and methanic processes are obtained. The water types can be connected to certain palaeo stages. This enables to estimate mean residence time of groundwaters. Current meteoric recharge stage (< 2500 a) mainly dominates in the upper 150 m. Groundwater from Litorina stage (7500-2500 a ago) forms the bulk at 100 - 250 m. Glacial melt water (about 10 000 a old) is an important component of groundwater between 100 - 500 m. However, any remarks of oxygen intrusion cannot be interpreted neither from mineralogy nor from groundwater. Deeper, subglacial and older saline groundwater predominates. Despite the current locations of different groundwater bodies it seems according to hydrogeochemical interpretation that dynamic flow conditions has been limited to upper 150 - 200 m. (orig.)

  11. Geochemical modelling of groundwater evolution and residence time at the Olkiluoto site

    Energy Technology Data Exchange (ETDEWEB)

    Pitkaenen, P.; Luukkonen, A. [VTT Communities and Infrastructure, Espoo (Finland); Ruotsalainen, P. [Fintact Oy (Finland); Leino-Forsman, H.; Vuorinen, U. [VTT Chemical Technology, Espoo (Finland)

    1999-05-01

    external conditions such as glaciation, palaeo Baltic stages, land uplift and ancient hydrothermal events, have had a significant effect on local palaeohydrogeological conditions. They have caused great variability, which is observable in the chemical data notably in salinity (up to 70 g/l), water type and contents of conservative parameters, such as Cl, Br and stable isotopes of water. However, their influence is also significant on the water-rock interaction that principally controls the pH and redox conditions - varying 7.5 to 8 and -200 to -300 mV, respectively - in the groundwater, although the calculated mass transfer in the reactions is minor compared with conservative mixing at the site. Calcite in fractures is interpreted to principally control pH level in groundwater. Sulphidic redox conditions dominate in the upper 500 m in brackish and slightly saline groundwater. Deeper sulphur species are absent and methanic processes are obtained. The water types can be connected to certain palaeo stages. This enables to estimate mean residence time of groundwaters. Current meteoric recharge stage (< 2500 a) mainly dominates in the upper 150 m. Groundwater from Litorina stage (7500-2500 a ago) forms the bulk at 100 - 250 m. Glacial melt water (about 10 000 a old) is an important component of groundwater between 100 - 500 m. However, any remarks of oxygen intrusion cannot be interpreted neither from mineralogy nor from groundwater. Deeper, subglacial and older saline groundwater predominates. Despite the current locations of different groundwater bodies it seems according to hydrogeochemical interpretation that dynamic flow conditions has been limited to upper 150 - 200 m. (orig.) 82 refs.

  12. DNA binding by PHF1 prolongs PRC2 residence time on chromatin and thereby promotes H3K27 methylation.

    Science.gov (United States)

    Choi, Jeongyoon; Bachmann, Andreas Linus; Tauscher, Katharina; Benda, Christian; Fierz, Beat; Müller, Jürg

    2017-12-01

    Polycomb repressive complex 2 (PRC2) trimethylates histone H3 at lysine 27 to mark genes for repression. We measured the dynamics of PRC2 binding on recombinant chromatin and free DNA at the single-molecule level using total internal reflection fluorescence (TIRF) microscopy. PRC2 preferentially binds free DNA with multisecond residence time and midnanomolar affinity. PHF1, a PRC2 accessory protein of the Polycomblike family, extends PRC2 residence time on DNA and chromatin. Crystallographic and functional studies reveal that Polycomblike proteins contain a winged-helix domain that binds DNA in a sequence-nonspecific fashion. DNA binding by this winged-helix domain accounts for the prolonged residence time of PHF1-PRC2 on chromatin and makes it a more efficient H3K27 methyltranferase than PRC2 alone. Together, these studies establish that interactions with DNA provide the predominant binding affinity of PRC2 for chromatin. Moreover, they reveal the molecular basis for how Polycomblike proteins stabilize PRC2 on chromatin and stimulate its activity.

  13. Receptor residence time trumps drug-likeness and oral bioavailability in determining efficacy of complement C5a antagonists

    Science.gov (United States)

    Seow, Vernon; Lim, Junxian; Cotterell, Adam J.; Yau, Mei-Kwan; Xu, Weijun; Lohman, Rink-Jan; Kok, W. Mei; Stoermer, Martin J.; Sweet, Matthew J.; Reid, Robert C.; Suen, Jacky Y.; Fairlie, David P.

    2016-04-01

    Drug discovery and translation are normally based on optimizing efficacy by increasing receptor affinity, functional potency, drug-likeness (rule-of-five compliance) and oral bioavailability. Here we demonstrate that residence time of a compound on its receptor has an overriding influence on efficacy, exemplified for antagonists of inflammatory protein complement C5a that activates immune cells and promotes disease. Three equipotent antagonists (3D53, W54011, JJ47) of inflammatory responses to C5a (3nM) were compared for drug-likeness, receptor affinity and antagonist potency in human macrophages, and anti-inflammatory efficacy in rats. Only the least drug-like antagonist (3D53) maintained potency in cells against higher C5a concentrations and had a much longer duration of action (t1/2 ~ 20 h) than W54011 or JJ47 (t1/2 ~ 1-3 h) in inhibiting macrophage responses. The unusually long residence time of 3D53 on its receptor was mechanistically probed by molecular dynamics simulations, which revealed long-lasting interactions that trap the antagonist within the receptor. Despite negligible oral bioavailability, 3D53 was much more orally efficacious than W54011 or JJ47 in preventing repeated agonist insults to induce rat paw oedema over 24 h. Thus, residence time on a receptor can trump drug-likeness in determining efficacy, even oral efficacy, of pharmacological agents.

  14. Survey of some natural decay-series isotopes in the Wairakei geothermal area and possible residence-time applications

    International Nuclear Information System (INIS)

    Concentrations of selected isotopes in the uranium decay series were determined for samples collected from the Wairakei, Broadlands/Ohaaki and Waiotapu areas. /sup 226/Ra concentrations were found to be low (0.05-0.22 dpm/l), similar to values reported in neutral hot springs at Tatun geothermal area, Taiwan, but lower than other geothermal systems (Yellowstone, USA, and Latera, Central Italy) (up to 25 dpm/l). The potential of /sup 226/Ra//sup 228/Ra ratios for indicating water residence times could not be explored because /sup 228/Ra data was not available. /sup 222/Rn concentrations are higher and related to steam fractions and CO/sub 2/ concentrations. The short half-life (3.8 days) makes /sup 222/Rn suitable for estimating residence times of radon in steam, and therefore the distance of travel of steam from its source (e.g., wells WK9 and 52). /sup 210/Pb and /sup 210/Po concentrations were very low and less than detection limits in many of the Wairakei waters; no residence time applications are apparent for these isotopes. (author). 11 refs.; 5 figs.; 3 tabs

  15. Receptor residence time trumps drug-likeness and oral bioavailability in determining efficacy of complement C5a antagonists

    Science.gov (United States)

    Seow, Vernon; Lim, Junxian; Cotterell, Adam J.; Yau, Mei-Kwan; Xu, Weijun; Lohman, Rink-Jan; Kok, W. Mei; Stoermer, Martin J.; Sweet, Matthew J.; Reid, Robert C.; Suen, Jacky Y.; Fairlie, David P.

    2016-01-01

    Drug discovery and translation are normally based on optimizing efficacy by increasing receptor affinity, functional potency, drug-likeness (rule-of-five compliance) and oral bioavailability. Here we demonstrate that residence time of a compound on its receptor has an overriding influence on efficacy, exemplified for antagonists of inflammatory protein complement C5a that activates immune cells and promotes disease. Three equipotent antagonists (3D53, W54011, JJ47) of inflammatory responses to C5a (3nM) were compared for drug-likeness, receptor affinity and antagonist potency in human macrophages, and anti-inflammatory efficacy in rats. Only the least drug-like antagonist (3D53) maintained potency in cells against higher C5a concentrations and had a much longer duration of action (t1/2 ~ 20 h) than W54011 or JJ47 (t1/2 ~ 1–3 h) in inhibiting macrophage responses. The unusually long residence time of 3D53 on its receptor was mechanistically probed by molecular dynamics simulations, which revealed long-lasting interactions that trap the antagonist within the receptor. Despite negligible oral bioavailability, 3D53 was much more orally efficacious than W54011 or JJ47 in preventing repeated agonist insults to induce rat paw oedema over 24 h. Thus, residence time on a receptor can trump drug-likeness in determining efficacy, even oral efficacy, of pharmacological agents. PMID:27094554

  16. Residence half-time of {sup 137}Cs in the top-soils of Japanese paddy and upland fields

    Energy Technology Data Exchange (ETDEWEB)

    Komamura, Misako [National Inst. of Agro-Environmental Sciences, Tsukuba, Ibaraki (Japan); Tsumura, Akito; Kodaira, Kiyoshi

    1999-03-01

    A series of top-soil samples of 14 paddy fields and 10 upland fields in Japan, were annually collected during more than 30 years, to be examined in the contents of {sup 137}Cs. The data, which were obtained by the use of a gamma spectrometric system, received some statistical treatments to distinguish the annual decline of {sup 137}Cs contents from deviations. Then the authors calculated `residence half-time of {sup 137}Cs` within top-soil, and `eluviation rate of {sup 137}Cs` from top to the sub-layer of the soil. The following nationwide results were obtained irrespective of paddy or upland field: (1) The `apparent residence half-time` was estimated as 16 - 17 years. This consists of both effects of eluviation and nuclear disintegration. (2) The true residence half-time` was reported as 41 - 42 years. This depends on the eluviation speed of {sup 137}Cs exclusively, because the influence of nuclear disintegration has been compensated. (3) The eluviation rate of {sup 137}Cs from top-soil down to the sub-soil was 1.6 - 1.7% per year. (4) The ratio of distribution of {sup 137}Cs between top-soil and the sub-soil was estimated to be 6:4 as average at the date of 1996. (author)

  17. Size-resolved measurement of the mixing state of soot in the megacity Beijing, China: diurnal cycle, aging and parameterization

    Directory of Open Access Journals (Sweden)

    Y. F. Cheng

    2012-05-01

    Full Text Available Soot particles are the most efficient light absorbing aerosol species in the atmosphere, playing an important role as a driver of global warming. Their climate effects strongly depend on their mixing state, which significantly changes their light absorbing capability and cloud condensation nuclei (CCN activity. Therefore, knowledge about the mixing state of soot and its aging mechanism becomes an important topic in the atmospheric sciences.

    The size-resolved (30–320 nm diameter mixing state of soot particles in polluted megacity air was measured at a suburban site (Yufa during the CAREBeijing 2006 campaign in Beijing, using a volatility tandem differential mobility analyzer (VTDMA. Particles in this size range with non-volatile residuals at 300 °C were considered to be soot particles. On average, the number fraction of internally mixed soot in total soot particles (Fin, decreased from 0.80 to 0.57 when initial Dp increased from 30 to 320 nm. Further analysis reveals that: (1 Fin was well correlated with the aerosol hygroscopic mixing state measured by a CCN counter. More externally mixed soot particles were observed when particles showed more heterogeneous features with regard to hygroscopicity. (2 Fin had pronounced diurnal cycles. For particles in the accumulation mode (Dp at 100–320 nm, largest Fin were observed at noon time, with "apparent" turnover rates (kex → in up to 7.8% h−1. (3 Fin was subject to competing effects of both aging and emissions. While aging increases Fin by converting externally mixed soot particles into internally mixed ones, emissions tend to reduce Fin by emitting more fresh and externally mixed soot particles. Similar competing effects were also found with air mass age indicators. (4 Under the estimated emission

  18. Ultrasensitive, Fast-Response Size-Dependent Soot Spectrometer Project

    Data.gov (United States)

    National Aeronautics and Space Administration — We propose to develop a "black carbon" (soot) monitor for measuring non-volatile particulate emissions from gas turbine engines employing a proprietary optical...

  19. Numerical Investigation of Soot Formation in Non-premixed Flames

    KAUST Repository

    Abdelgadir, Ahmed Gamaleldin

    2017-05-01

    Soot is a carbon particulate formed as a result of the combustion of fossil fuels. Due to the health hazard posed by the carbon particulate, government agencies have applied strict regulations to control soot emissions from road vehicles, airplanes, and industrial plants. Thus, understanding soot formation and evolution is critical. Practical combustion devices operate at high pressure and in the turbulent regime. Elevated pressures and turbulence on soot formation significantly and fundamental understanding of these complex interactions is still poor. In this study, the effects of pressure and turbulence on soot formation and growth are investigated numerically. As the first step, the evolution of the particle size distribution function (PSDF) and soot particles morphology are investigated in turbulent non-premixed flames. A Direct Simulation Monte Carlo (DSMC) code is developed and used. The stochastic reactor describes the evolution of soot in fluid parcels following Lagrangian trajectories in a turbulent flow field. The trajectories are sampled from a Direct Numerical Simulation (DNS) of an n-heptane turbulent non-premixed flame. Although individual trajectories display strong bimodality as in laminar flames, the ensemble-average PSDF possesses only one mode and a broad tail, which implies significant polydispersity induced by turbulence. Secondly, the effect of the flow and mixing fields on soot formation at atmospheric and elevated pressures is investigated in coflow laminar diffusion flames. The experimental observation and the numerical prediction of the spatial distribution are in good agreement. Based on the common scaling methodology of the flames (keeping the Reynolds number constant), the scalar dissipation rate decreases as pressure increases, promoting the formation of PAH species and soot. The decrease of the scalar dissipation rate significantly contributes to soot formation occurring closer to the nozzle and outward on the flames wings as pressure

  20. Investigating Soot Morphology in Counterflow Flames at Elevated Pressures

    KAUST Repository

    Amin, Hafiz Muhammad Fahid

    2018-01-01

    Practical combustion devices such as gas turbines and diesel engines operate at high pressures to increase their efficiency. Pressure significantly increases the overall soot yield. Morphology of these ultra-fine particles determines their airborne lifetime and their interaction with the human respiratory system. Therefore, investigating soot morphology at high pressure is of practical relevance. In this work, a novel experimental setup has been designed and built to study the soot morphology at elevated pressures. The experimental setup consists of a pressure vessel, which can provide optical access from 10° to 165° for multi-angle light scattering, and a counterflow burner which produces laminar flames at elevated pressures. In the first part of the study, N2-diluted ethylene/air and ethane air counterflow flames are stabilized from 2 to 5 atm. Two-angle light scattering and extinction technique have been used to study the effects of pressure on soot parameters. Path averaged soot volume fraction is found to be very sensitive to pressure and increased significantly from 2 to 5 atm. Primary particle size and aggregate size also increased with pressure. Multi-angle light scattering is also performed and flames are investigated from 3 to 5 atm. Scattering to absorption ratio is calculated from multi-angle light scattering and extinction data. Scattering to absorption ratio increased with pressure whereas the number of primary particles in an aggregate decreased with increasing pressure. In the next part of the study, Thermophoretic Sampling of soot is performed, in counterflow flames from 3 to 10 atm, followed by transmission electron microscopy. Mean primary particle size increased with pressure and these trends are consistent withour light scattering measurements. Fractal properties of soot aggregates are found to be insensitive to pressure. 2D diffused light line of sight attenuation (LOSA) and Laser Induced Incandescence (LII) are used to measure local soot

  1. The distribution of range sizes of native and alien plants in four European countries and the effects of residence time

    OpenAIRE

    Williamson, Mark; Dehnen-Schmutz, Katharina; Kühn, Ingolf; Hill, Mark; Klotz, Stefan; Milbau , Ann; Stout, Jane; Pyšek, Petr

    2009-01-01

    Aim Do the statistical distributions of range sizes of native and alien species differ? If so, is this because of residence time effects? And can such effects indicate an average time to a maximum?\\ud \\ud Location Ireland, Britain, Germany and the Czech Republic.\\ud \\ud Methods The data are presence or absence of higher plants in mapping units of 100 km2 (Ireland and Britain) or c. 130 km2 (Germany and the Czech Republic) in areas varying from 79 to 357 thousand km2. Logit transforms of range...

  2. TEM and HRTEM of Soot-in-oil particles and agglomerates from internal combustion engines

    International Nuclear Information System (INIS)

    Fay, M W; Rocca, A La; Shayler, P J

    2014-01-01

    Over time, the performance of lubricating oil in a diesel engine is affected by the build-up of carbon soot produced by the combustion process. TEM and HRTEM are commonly used to investigate the characteristics of individual and agglomerated particles from diesel exhaust, to understand the structure and distribution of the carbon sheets in the primary particles and the nanostructure morphology. However, high resolution imaging of soot-in-oil is more challenging, as mineral oil is a contaminant for the electron microscope and leads to instability under the electron beam. In this work we compare solvent extraction and centrifugation techniques for removing the mineral oil contaminant, and the effect on particle size distribution

  3. The reduction of soot formation from fuels using oxygenates additives

    International Nuclear Information System (INIS)

    Burshaid, K.I.; Hamdan, M.A.

    2013-01-01

    Highlights: ► Understanding of the performance of thermo chemical heat pump. ► Tool for storing thermal energy. ► Parameters that affect the amount of thermal stored energy. ► Lithium chloride has better effect on storing thermal energy. - Abstract: This work presents an experimental technique for the measurement of the soot formation in pure fuel, biofuel and emulsified fuel, that constitute this fuels was studied in heated shock tube and investigated the possibility of reducing soot production in locally refined diesel, locally produced biofuel and emulsified fuel. This reduction was conducted using certain oxygenated additives (methane, ethane and acetone). It was found that soot concentration is maximum when pure diesel was burned, followed by emulsified fuels and the lease concentration was obtained when biofuel was burned. Further, methanol has the most significant effect on the reduction of soot once added to each fuel, while acetone has the lease effect on soot reduction. The results gave good indication of the effect for oxygenated additives in reduction the soot formation.

  4. Emission of ions and charged soot particles by aircraft engines

    Directory of Open Access Journals (Sweden)

    A. Sorokin

    2003-01-01

    Full Text Available In this article, a model which examines the formation and evolution of chemiions in an aircraft engine is proposed. This model which includes chemiionisation, electron thermo-emission, electron attachment to soot particles and to neutral molecules, electron-ion and ion-ion recombination, ion-soot interaction, allows the determination of the ion concentration at the exit of the combustor and at the nozzle exit of the engine. It also allows the determination of the charge of the soot particles. For the engine considered, the upper limit for the ion emission index EIi is of the order of (2-5 x1016 ions/kg-fuel if ion-soot interactions are ignored and the introduction of ion-soot interactions lead about to a 50% reduction. The results also show that most of the soot particles are either positively or negatively charged, the remaining neutral particles representing approximately 20% of the total particles. A comparison of the model results with the available ground-based experimental data obtained on the ATTAS research aircraft engines during the SULFUR experiments (Schumann, 2002 shows an excellent agreement.

  5. Durable superhydrophobic carbon soot coatings for sensor applications

    Science.gov (United States)

    Esmeryan, K. D.; Radeva, E. I.; Avramov, I. D.

    2016-01-01

    A novel approach for the fabrication of durable superhydrophobic (SH) carbon soot coatings used in quartz crystal microbalance (QCM) based gas or liquid sensors is reported. The method uses modification of the carbon soot through polymerization of hexamethyldisiloxane (HMDSO) by means of glow discharge RF plasma. The surface characterization shows a fractal-like network of carbon nanoparticles with diameter of ~50 nm. These particles form islands and cavities in the nanometer range, between which the plasma polymerized hexamethyldisiloxane (PPHMDSO) embeds and binds to the carbon chains and QCM surface. Such modified surface structure retains the hydrophobic nature of the soot and enhances its robustness upon water droplet interactions. Moreover, it significantly reduces the insertion loss and dynamic resistance of the QCM compared to the commonly used carbon soot/epoxy resin approach. Furthermore, the PPHMDSO/carbon soot coating demonstrates durability and no aging after more than 40 probing cycles in water based liquid environments. In addition, the surface layer keeps its superhydrophobicity even upon thermal annealing up to 540 °C. These experiments reveal an opportunity for the development of soot based SH QCMs with improved electrical characteristics, as required for high-resolution gas or liquid measurements.

  6. Uptake of HNO3 on hexane and aviation kerosene soots.

    Science.gov (United States)

    Talukdar, Ranajit K; Loukhovitskaya, Ekaterina E; Popovicheva, Olga B; Ravishankara, A R

    2006-08-10

    The uptake of HNO(3) on aviation kerosene (TC-1) soot was measured as a function of temperature (253-295 K) and the partial pressure of HNO(3), and the uptake of HNO(3) on hexane soot was studied at 295 K and over a limited partial pressure of HNO(3). The HNO(3) uptake was mostly reversible and did not release measurable amounts of gas-phase products such as HONO, NO(3), NO(2) or N(2)O(5). The heat of adsorption of HNO(3) on soot was dependent on the surface coverage. The isosteric heats of adsorption, Delta(0)H(isosteric), were determined as a function of coverage. Delta(0)H(isosteric) values were in the range -16 to -13 kcal mol(-1). The heats of adsorption decrease with increasing coverage. The adsorption data were fit to Freundlich and to Langmuir-Freundlich isotherms. The heterogeneity parameter values were close to 0.5, which suggested that a HNO(3) molecule can occupy two sites on the surface with or without being dissociated and that the soot surface could be nonuniform. Surface FTIR studies on the interaction of soot with HNO(3) did not reveal formation of any minor product such as organic nitrate or nitro compound on the soot surface. Using our measured coverage, we calculate that the partitioning of gas-phase nitric acid to black carbon aerosol is not a significant loss process of HNO(3) in the atmosphere.

  7. Durable superhydrophobic carbon soot coatings for sensor applications

    International Nuclear Information System (INIS)

    Esmeryan, K D; Radeva, E I; Avramov, I D

    2016-01-01

    A novel approach for the fabrication of durable superhydrophobic (SH) carbon soot coatings used in quartz crystal microbalance (QCM) based gas or liquid sensors is reported. The method uses modification of the carbon soot through polymerization of hexamethyldisiloxane (HMDSO) by means of glow discharge RF plasma. The surface characterization shows a fractal-like network of carbon nanoparticles with diameter of ∼50 nm. These particles form islands and cavities in the nanometer range, between which the plasma polymerized hexamethyldisiloxane (PPHMDSO) embeds and binds to the carbon chains and QCM surface. Such modified surface structure retains the hydrophobic nature of the soot and enhances its robustness upon water droplet interactions. Moreover, it significantly reduces the insertion loss and dynamic resistance of the QCM compared to the commonly used carbon soot/epoxy resin approach. Furthermore, the PPHMDSO/carbon soot coating demonstrates durability and no aging after more than 40 probing cycles in water based liquid environments. In addition, the surface layer keeps its superhydrophobicity even upon thermal annealing up to 540 °C. These experiments reveal an opportunity for the development of soot based SH QCMs with improved electrical characteristics, as required for high-resolution gas or liquid measurements. (paper)

  8. Measurement of Soot Deposition in Automotive Components Using Neutron Radiography

    International Nuclear Information System (INIS)

    Zekveld, David; Liu, Liaohui; Harrison, Andrew; Gill, Spencer; Harvel, Glenn; Chang, Jen-Shih

    2008-01-01

    About 40% of air pollution is generated by vehicles and transportation. The particulate matter (PM) emission significantly impacts human health. Fine particles below 2.5 μm (PM2.5) can enter the lungs and lead to respiratory problems. These particles not only influence human health, but also reduce the capability of many automobile exhaust heat exchanging devices. Neutron radiography is a non-destructive method of analyzing carbonaceous PM. While neutron radiography has been demonstrated for soot measurement in the past, the application has not considered the presence of unburned hydrocarbons, significant amounts of moisture nor examined complex geometrical configurations. The purpose of this work is to study a reliable non-destructive testing methodology using neutron radiography for measurement of soot distribution in automotive components. A soot standard (aluminium target) was designed and manufactured as a calibration tool. The standard is radiographed and used to measure the differences between various soot thickness and compositions. The radiograph images are analyzed to determine a calibration curve based upon the composition of the materials which can then be used for analysis of the automotive components. Experiments are performed using a diesel engine to produce soot deposits on exhaust piping. Soot distribution on exhaust piping is measured using neutron radiography. (authors)

  9. Response to Comment on “Modeling Maximum Adsorption Capacities of Soot and Soot-like Materials for PAHs and PCBs”

    NARCIS (Netherlands)

    Noort, van P.C.M.; Jonker, M.T.O.; Koelmans, A.A.

    2005-01-01

    A comment by John C. Fetzer on modeling maximum adsorption capacities of soot and soot-like materials for PAH and PCB and the adsorption behavior of PAH on soots and on other adsorptive materials is presented. The authors (van Noort et al.) base their model on van der Waal's forces only. This may be

  10. Facile synthesis of nano cauliflower and nano broccoli like hierarchical superhydrophobic composite coating using PVDF/carbon soot particles via gelation technique.

    Science.gov (United States)

    Sahoo, Bichitra Nanda; Balasubramanian, Kandasubramanian

    2014-12-15

    We have elucidated a cost effective fabrication technique to produce superhydrophobic polyvinylidene fluoride (PVDF/DMF/candle soot particle and PVDF/DMF/camphor soot particle composite) porous materials. The water repellent dry composite was formed by the interaction of non-solvent (methanol) into PVDF/carbon soot particles suspension in N,N-dimethylformamide (DMF). It is seen that longer quenching time effectively changes the surface morphology of dry composites. The nano broccoli like hierarchical microstructure with micro or nano scaled roughen surface was obtained for PVDF/DMF/camphor soot particle, which reveals water contact angle of 172° with roll off angle of 2°. However, composite coating of PVDF/DMF/candle soot particle shows nano cauliflower like hierarchical, which illustrates water contact angle of 169° with roll off angle of 3°. To elucidate the enhancement of water repellent property of PVDF composites, we further divulge the evolution mechanism of nano cauliflower and nano broccoli structure. In order to evaluate the water contact angle of PVDF composites, surface diffusion of water inside the pores is investigated. Furthermore, the addition of small amount of carbon soot particles in composite not only provides the crystallization of PVDF, but also leads to dramatical amendment of surface morphology which increases the surface texture and roughness for superhydrophobicity. Copyright © 2014 Elsevier Inc. All rights reserved.

  11. Maintaining social cohesion is a more important determinant of patch residence time than maximizing food intake rate in a group-living primate, Japanese macaque (Macaca fuscata).

    Science.gov (United States)

    Kazahari, Nobuko

    2014-04-01

    Animals have been assumed to employ an optimal foraging strategy (e.g., rate-maximizing strategy). In patchy food environments, intake rate within patches is positively correlated with patch quality, and declines as patches are depleted through consumption. This causes patch-leaving and determines patch residence time. In group-foraging situations, patch residence times are also affected by patch sharing. Optimal patch models for groups predict that patch residence times decrease as the number of co-feeding animals increases because of accelerated patch depletion. However, group members often depart patches without patch depletion, and their patch residence time deviates from patch models. It has been pointed out that patch residence time is also influenced by maintaining social proximity with others among group-living animals. In this study, the effects of maintaining social cohesion and that of rate-maximizing strategy on patch residence time were examined in Japanese macaques (Macaca fuscata). I hypothesized that foragers give up patches to remain in the proximity of their troop members. On the other hand, foragers may stay for a relatively long period when they do not have to abandon patches to follow the troop. In this study, intake rate and foraging effort (i.e., movement) did not change during patch residency. Macaques maintained their intake rate with only a little foraging effort. Therefore, the patches were assumed to be undepleted during patch residency. Further, patch residence time was affected by patch-leaving to maintain social proximity, but not by the intake rate. Macaques tended to stay in patches for short periods when they needed to give up patches for social proximity, and remained for long periods when they did not need to leave to keep social proximity. Patch-leaving and patch residence time that prioritize the maintenance of social cohesion may be a behavioral pattern in group-living primates.

  12. A review of radioactive isotopes and other residence time tracers in understanding groundwater recharge: Possibilities, challenges, and limitations

    Science.gov (United States)

    Cartwright, Ian; Cendón, Dioni; Currell, Matthew; Meredith, Karina

    2017-12-01

    Documenting the location and magnitude of groundwater recharge is critical for understanding groundwater flow systems. Radioactive tracers, notably 14C, 3H, 36Cl, and the noble gases, together with other tracers whose concentrations vary over time, such as the chlorofluorocarbons or sulfur hexafluoride, are commonly used to estimate recharge rates. This review discusses some of the advantages and problems of using these tracers to estimate recharge rates. The suite of tracers allows recharge to be estimated over timescales ranging from a few years to several hundred thousand years, which allows both the long-term and modern behaviour of groundwater systems to be documented. All tracers record mean residence times and mean recharge rates rather than a specific age and date of recharge. The timescale over which recharge rates are averaged increases with the mean residence time. This is an advantage in providing representative recharge rates but presents a problem in comparing recharge rates derived from these tracers with those from other techniques, such as water table fluctuations or lysimeters. In addition to issues relating to the sampling and interpretation of specific tracers, macroscopic dispersion and mixing in groundwater flow systems limit how precisely groundwater residence times and recharge rates may be estimated. Additionally, many recharge studies have utilised existing infrastructure that may not be ideal for this purpose (e.g., wells with long screens that sample groundwater several kilometres from the recharge area). Ideal recharge studies would collect sufficient information to optimise the use of specific tracers and minimise the problems of mixing and dispersion.

  13. Modeling sediment transport processes and residence times in the shallow coastal bay complex of the Virginia Coast Reserve

    Science.gov (United States)

    Safak, I.; Wiberg, P. L.

    2011-12-01

    Patterns of sediment transport and particle residence times influence the morphology and ecology of shallow coastal bays in important ways. The Virginia Coast Reserve (VCR), a barrier island-lagoon-marsh system on the Eastern Shore of Virginia, is typical of many shallow coastal bay complexes that lack a significant fluvial source of freshwater and sediment. Sediment redistribution within the bays in response to storms and sea-level rise, together with the dynamics of marsh and lagoon-bottom plants, largely governs the morphological evolution of this system. There are also important feedbacks between sediment and ecosystem dynamics. This is particularly true in the VCR, which is relatively unaffected by human activities. As a step towards evaluating the impact of hydrodynamics on sediment and ecological processes in the VCR, a single unified model that accounts for circulation, surface waves, wave-current interaction, and sediment processes is employed. This three-dimensional unstructured grid finite-volume coastal ocean model (FVCOM) is validated with field observations of wind- and tide-induced water flow (water level and current velocities) in Hog Island Bay, centrally located within the VCR. Here, the resulting patterns of sediment transport and particle residence times over event and seasonal time scales are presented. Water and particle exchange within the VCR and between the VCR and the ocean is examined with the Lagrangian particle-tracking module in FVCOM. We focus on three bays with strongly varying bathymetry and coastline geometry, which are also located along a gradient of nitrogen input to the system. The results indicate that residence time of particles within the system vary greatly depending on the location of particle release, bay morphology, and wind conditions. The implications for morphologic evolution and ecosystem response to climate and land-use changes are evaluated.

  14. Catchment virtual observatory for sharing flow and transport models outputs: using residence time distribution to compare contrasting catchments

    Science.gov (United States)

    Thomas, Zahra; Rousseau-Gueutin, Pauline; Kolbe, Tamara; Abbott, Ben; Marcais, Jean; Peiffer, Stefan; Frei, Sven; Bishop, Kevin; Le Henaff, Geneviève; Squividant, Hervé; Pichelin, Pascal; Pinay, Gilles; de Dreuzy, Jean-Raynald

    2017-04-01

    The distribution of groundwater residence time in a catchment provides synoptic information about catchment functioning (e.g. nutrient retention and removal, hydrograph flashiness). In contrast with interpreted model results, which are often not directly comparable between studies, residence time distribution is a general output that could be used to compare catchment behaviors and test hypotheses about landscape controls on catchment functioning. In this goal, we created a virtual observatory platform called Catchment Virtual Observatory for Sharing Flow and Transport Model Outputs (COnSOrT). The main goal of COnSOrT is to collect outputs from calibrated groundwater models from a wide range of environments. By comparing a wide variety of catchments from different climatic, topographic and hydrogeological contexts, we expect to enhance understanding of catchment connectivity, resilience to anthropogenic disturbance, and overall functioning. The web-based observatory will also provide software tools to analyze model outputs. The observatory will enable modelers to test their models in a wide range of catchment environments to evaluate the generality of their findings and robustness of their post-processing methods. Researchers with calibrated numerical models can benefit from observatory by using the post-processing methods to implement a new approach to analyzing their data. Field scientists interested in contributing data could invite modelers associated with the observatory to test their models against observed catchment behavior. COnSOrT will allow meta-analyses with community contributions to generate new understanding and identify promising pathways forward to moving beyond single catchment ecohydrology. Keywords: Residence time distribution, Models outputs, Catchment hydrology, Inter-catchment comparison

  15. The Effects of Particle Size, Different Corn Stover Components, and Gas Residence Time on Torrefaction of Corn Stover

    Directory of Open Access Journals (Sweden)

    Sarah Rahn

    2012-04-01

    Full Text Available Large scale biofuel production will be possible only if significant quantities of biomass feedstock can be stored, transported, and processed in an economic and sustainable manner. Torrefaction has the potential to significantly reduce the cost of transportation, storage, and downstream processing through the improvement of physical and chemical characteristics of biomass. The main objective of this study was to investigate the effects of particle size, plant components, and gas residence time on the production of torrefied corn (Zea mays stover. Different particle sizes included 0.85 mm and 20 mm. Different stover components included ground corn stover, whole corn stalk, stalk shell and pith, and corn cob shell. Three different purge gas residence times were employed to assess the effects of interaction of volatiles and torrefied biomass. Elemental analyses were performed on all of the samples, and the data obtained was used to estimate the energy contents and energy yields of different torrefied biomass samples. Particle density, elemental composition, and fiber composition of raw biomass fractions were also determined. Stalk pith torrefied at 280 °C and stalk shell torrefied at 250 °C had highest and lowest dry matter loss, of about 44% and 13%, respectively. Stalk pith torrefied at 250 °C had lowest energy density of about 18–18.5 MJ/kg, while cob shell torrefied at 280 °C had the highest energy density of about 21.5 MJ/kg. The lowest energy yield, at 59%, was recorded for stalk pith torrefied at 280 °C, whereas cob and stalk shell torrefied at 250 °C had highest energy yield at 85%. These differences were a consequence of the differences in particle densities, hemicellulose quantities, and chemical properties of the original biomass samples. Gas residence time did not have a significant effect on the aforementioned parameters.

  16. Target Residence Time-Guided Optimization on TTK Kinase Results in Inhibitors with Potent Anti-Proliferative Activity.

    Science.gov (United States)

    Uitdehaag, Joost C M; de Man, Jos; Willemsen-Seegers, Nicole; Prinsen, Martine B W; Libouban, Marion A A; Sterrenburg, Jan Gerard; de Wit, Joeri J P; de Vetter, Judith R F; de Roos, Jeroen A D M; Buijsman, Rogier C; Zaman, Guido J R

    2017-07-07

    The protein kinase threonine tyrosine kinase (TTK; also known as Mps1) is a critical component of the spindle assembly checkpoint and a promising drug target for the treatment of aggressive cancers, such as triple negative breast cancer. While the first TTK inhibitors have entered clinical trials, little is known about how the inhibition of TTK with small-molecule compounds affects cellular activity. We studied the selective TTK inhibitor NTRC 0066-0, which was developed in our own laboratory, together with 11 TTK inhibitors developed by other companies, including Mps-BAY2b, BAY 1161909, BAY 1217389 (Bayer), TC-Mps1-12 (Shionogi), and MPI-0479605 (Myrexis). Parallel testing shows that the cellular activity of these TTK inhibitors correlates with their binding affinity to TTK and, more strongly, with target residence time. TTK inhibitors are therefore an example where target residence time determines activity in in vitro cellular assays. X-ray structures and thermal stability experiments reveal that the most potent compounds induce a shift of the glycine-rich loop as a result of binding to the catalytic lysine at position 553. This "lysine trap" disrupts the catalytic machinery. Based on these insights, we developed TTK inhibitors, based on a (5,6-dihydro)pyrimido[4,5-e]indolizine scaffold, with longer target residence times, which further exploit an allosteric pocket surrounding Lys553. Their binding mode is new for kinase inhibitors and can be classified as hybrid Type I/Type III. These inhibitors have very potent anti-proliferative activity that rivals classic cytotoxic therapy. Our findings will open up new avenues for more applications for TTK inhibitors in cancer treatment. Copyright © 2017 Elsevier Ltd. All rights reserved.

  17. In-cylinder Combustion and Soot Evolution in the Transition from Conventional CI mode to PPC

    KAUST Repository

    An, Yanzhao

    2018-01-09

    The present study intends to explore the in-cylinder combustion and evolution of soot emission during the transition from conventional compression ignition (CI) combustion to partially premixed combustion (PPC) at low load conditions. In-cylinder combustion images and engine-out emissions were measured in an optical engine fueled with low octane heavy naphtha fuel (RON = 50). Full cycle engine simulations were performed using a three-dimensional computational fluid dynamics code CONVERGETM, coupled with gas phase chemical kinetics, turbulence, and particulate size mimic soot model. The simulations were performed under low load conditions (IMEP ~ 2 to 3 bar) at an engine speed of 1200 rpm. The start of injection (SOI) was advanced from late (-10 CAD aTDC) to early fuel injection timings (-40 CAD aTDC) to realize the combustion transition from CI combustion to PPC. The simulation results of combustion and emission are compared with the experimental results at both CI and PPC combustion modes. The results of the study show a typical low-temperature stratified lean combustion at PPC mode, while high-temperature spray-driven combustion is evident at CI mode. The in-cylinder small intermediates species such as acetylene (C2H2), propargyl (C3H3), cyclopentadienyl (C5H5) and polycyclic aromatic hydrocarbons (PAHs) were significantly suppressed at PPC mode. Nucleation reaction of PAHs collision contributed to main soot mass production. The distribution of soot mass and particle number density was consistent with the distribution of high-temperature zones at CI and PPC combustion modes.

  18. Impact of Temperature and Hydrological Residence Time on the Fate and Transport of Iron and Organic Carbon in Subalpine Wetlands

    Science.gov (United States)

    Schneider, L. M.; Borch, T.; Rhoades, C.; Pallud, C. E.

    2015-12-01

    Wetlands contain one third of the planet's soil carbon (C) and are characterized by markedly different chemical and physical environments than terrestrial ecosystems. The hydrologic residence time and temperature in wetlands influences their redox conditions and thus biogeochemical reaction rates. In these environments, transformation and movement of C and iron (Fe) are closely linked due to the sorption of organic C by solid Fe(III)-phases. Therefore, changes in Fe biogeochemical cycling will influence the size and turnover rate of soil C pools, which could negatively impact water quality and C storage. We examined the effects of hydrologic residence time and temperature on reduction of autochtonous Fe(III)-oxides. Fe(II)-export rates, used as a lower bound for bulk Fe(III)-reduction rates, and dissolved organic carbon (DOC) export rates were measured on intact mineral soil cores using flow-through reactor experiments exposed to temperatures based on mean annual conditions (6°, 12°, and 18°C). Soils were from a slope and a depressional subalpine wetland (USDA Fraser Experimental Forest, CO, USA), characterized by different hydrologic residence times, were compared. In the depressional wetland we observed the shallower soil depths have higher overall Fe(II)-export rates than the deeper soil depths. As temperature increases, Fe(II)-export rate increases, with a more than doubling in magnitude from 12 to 18° C. In comparing sites that are continuously inundated to those that are seasonally inundated, surprisingly we see higher Fe(II)-export rates in the seasonally inundated sites for all temperatures and depths. In the slope wetland we observed an opposite trend with depth and with temperature, with Fe(II)-export rates declining by almost an order of magnitude between 6 and 12°C. In addition, our results showed a positive correlation between Fe(II)-export rates and DOC export rates suggesting Fe(III)-reduction exerts a biogeochemical control on water quality

  19. Fly Ash Formation during Suspension-Firing of Biomass. Effects of Residence Time and Fuel-Type

    DEFF Research Database (Denmark)

    Damø, Anne Juul; Jensen, Peter Arendt; Jappe Frandsen, Flemming

    2017-01-01

    particles were subjected to various analyses, including char burnout level, particle size distribution, elemental composition, and particle morphology and composition. Furthermore, the transient release, i.e. the vaporization of the flame-volatile inorganic elements K, Cl and S, from the burning fuel...... particles to the gas phase, has been quantified by using two different calculation methods. The ash formation mechanisms were found to be quite similar for straw and wood. The degree of conversion (char burn-out level) was generally good at residence times ≥ 1s. The size distribution of the residual fly ash...

  20. Determination of the residence time of rain water in some hydrographic basins by means of stable isotopes

    International Nuclear Information System (INIS)

    Goncalves, A.R.L.

    1979-10-01

    Samples of rain-and river water, monthly collected during one year from ten stations of the Amazon basin analysed in their 18 O and D content. The residence time of rain water for each station was determined using the values of Δ 18 O(%o) and ΔD(%). The values of Δ 18 O(%o) were correlated with the precipitation ones (mm) in order to determine the occurence of 'amount effect' in the stations. An analysis of samples was done along the Amazon River for simple observation of the 'isotopic fractionation' phenomenon the values of Δ 18 O(%o). (Author) [pt

  1. A Review on Diesel Soot Emission, its Effect and Control

    Directory of Open Access Journals (Sweden)

    R. Prasad

    2011-01-01

    Full Text Available The diesel engines are energy efficient, but their particulate (soot emissions are responsible of severe environmental and health problems. This review provides a survey on published information regarding diesel soot emission, its adverse effects on the human health, environment, vegetations, climate, etc. The legislations to limit diesel emissions and ways to minimize soot emission are also summarized. Soot particles are suspected to the development of cancer; cardiovascular and respiratory health effects; pollution of air, water, and soil; impact agriculture productivity, soiling of buildings; reductions in visibility; and global climate change. The review covers important recent developments on technologies for control of particulate matter (PM; diesel particulate filters (DPFs, summarizing new filter and catalyst materials and DPM measurement. DPF technology is in a state of optimization and cost reduction. New DPF regeneration strategies (active, passive and plasma-assisted regenerations as well as the new learning on the fundamentals of soot/catalyst interaction are described. Recent developments in diesel oxidation catalysts (DOC are also summarized showing potential issues with advanced combustion strategies, important interactions on NO2 formation, and new formulations for durability. Finally, systematic compilation of the concerned newer literature on catalytic oxidation of soot in a well conceivable tabular form is given. A total of 156 references are cited. ©2010 BCREC UNDIP. All rights reserved(Received: 2nd June 2010, Revised: 17th June 2010; Accepted: 24th June 2010[How to Cite: R. Prasad, V.R. Bella. (2010. Review on Diesel Soot Emission, its Effect and Control. Bulletin of Chemical Reaction Engineering and Catalysis, 5(2: 69-86. doi:10.9767/bcrec.5.2.794.69-86][DOI: http://dx.doi.org/10.9767/bcrec.5.2.794.69-86 || or local:   http://ejournal.undip.ac.id/index.php/bcrec/article/view/794 ]Cited by in: ACS 1 |

  2. Experimental determination of soot refractive index in the infrared

    International Nuclear Information System (INIS)

    Ouf, F.X.; Vendel, J.; Ouf, F.X.; Coppalle, A.; Weil, M.E.; Yon, J.

    2007-01-01

    The study of physical properties of soot particles produced during combustion is a complex subject but of a great interest within the framework of the study of the safety of an installation, with respect to the fire hazard. These characteristics are, in this case, particularly useful in order to predict the behaviour of containment barriers in situation of fire, but also in order to estimate the contribution of these particles to radiative transfers. The aim of this study is to determine the radiative properties of soot particles produced during combustion. A specific device, which establishes extinction and vertical-vertical scattering coefficients, has been developed and has allowed to determine the refractive index of soot particles in the infrared. This determination also needed the establishment of size distribution and morphological properties of soot aggregates. We present in this document the experimental device developed, and the validation of this device on latex spheres which optical properties are well known. First results of extinction coefficients will be presented and will underline the similar optical behaviour of different soot aggregates. Values of refractive index will be detailed and discussed, and a direct application of these values will be carried out in order to determine the soot volume fraction. A comparison with reference method will underline the efficiency of our method. We will conclude on the validity of the information brought by this device and on the prospects of this study. A discussion is included, on the utility of mean values of refractive index and on the determination of total emissivity of soot particles. (authors)

  3. Ignition delay and soot oxidative reactivity of MTBE blended diesel fuel

    KAUST Repository

    Yang, Seung Yeon

    2014-04-01

    Methyl tert-butyl ether (MTBE) was added to diesel fuel to investigate the effect on ignition delay and soot oxidative reactivity. An ignition quality tester (IQT) was used to study the ignition propensity of MTBE blended diesel fuels in a reactive spray environment. The IQT data showed that ignition delay increases linearly as the MTBE fraction increases in the fuel. A four-stroke single cylinder diesel engine was used to generate soot samples for a soot oxidation study. Soot samples were pre-treated using a tube furnace in a nitrogen environment to remove any soluble organic fractions and moisture content. Non-isothermal oxidation of soot samples was conducted using a thermogravimetric analyzer (TGA). It was observed that oxidation of \\'MTBE soot\\' started began at a lower temperature and had higher reaction rate than \\'diesel soot\\' across a range of temperatures. Several kinetic analyses including an isoconversional method and a combined model fitting method were carried out to evaluate kinetic parameters. The results showed that Diesel and MTBE soot samples had similar activation energy but the pre-exponential factor of MTBE soot was much higher than that of the Diesel soot. This may explain why MTBE soot was more reactive than Diesel soot. It is suggested that adding MTBE to diesel fuel is better for DPF regeneration since an MTBE blend can significantly influence the ignition characteristics and, consequently, the oxidative reactivity of soot. Copyright © 2014 SAE International.

  4. Microscopic investigation of soot and ash particulate matter derived from biofuel and diesel: implications for the reactivity of soot

    Science.gov (United States)

    Liati, Anthi; Spiteri, Alexander; Dimopoulos Eggenschwiler, Panayotis; Vogel-Schäuble, Nina

    2012-11-01

    Investigation of soot and ash particulate matter deposited in diesel particulate filters (DPFs) operating with biofuel (B100) and diesel (pure diesel: B0 and diesel80/biofuel20 blend: B20) by means of optical microscopy, scanning electron microscopy, and high resolution transmission electron microscopy (HRTEM) reveals the following: the rapeseed methyl ester biofuel used for this study contributes to ash production, mainly of Ca-S- and P-bearing compounds ranging in size between 50 and 300 nm. Smaller ash particles are less common and build aggregates. Ash is deposited on the inlet DPF surface, the inlet channel walls, and in B100-DPF at the plugged ends of inlet channels. The presence of Fe-Cr-Ni fragments, down to tens of nanometers in size within the ash is attributed to engine wear. Pt particles (50-400 nm large) within the ash indicate that the diesel oxidation catalyst (DOC) upstream of the DPF shows aging effects. Radial cracks on the coating layer of the DOC confirm this assumption. The B100-DPF contains significantly less soot than B20 and B0. Based on the generally accepted view that soot reactivity correlates with the nanostructure of its primary particles, the length and curvature of graphene sheets from biofuel- and diesel-derived soot were measured and computed on the basis of HRTEM images. The results show that biofuel-derived soot can be more easily oxidized than diesel soot, not only during early formation but also during and after considerable particle growth. Differences in the graphene sheet separation distance, degree of crystalline order and size of primary soot particles between the two fuel types are in line with this inference.

  5. Microscopic investigation of soot and ash particulate matter derived from biofuel and diesel: implications for the reactivity of soot

    International Nuclear Information System (INIS)

    Liati, Anthi; Spiteri, Alexander; Dimopoulos Eggenschwiler, Panayotis; Vogel-Schäuble, Nina

    2012-01-01

    Investigation of soot and ash particulate matter deposited in diesel particulate filters (DPFs) operating with biofuel (B100) and diesel (pure diesel: B0 and diesel 80 /biofuel 20 blend: B20) by means of optical microscopy, scanning electron microscopy, and high resolution transmission electron microscopy (HRTEM) reveals the following: the rapeseed methyl ester biofuel used for this study contributes to ash production, mainly of Ca–S– and P-bearing compounds ranging in size between 50 and 300 nm. Smaller ash particles are less common and build aggregates. Ash is deposited on the inlet DPF surface, the inlet channel walls, and in B100-DPF at the plugged ends of inlet channels. The presence of Fe–Cr–Ni fragments, down to tens of nanometers in size within the ash is attributed to engine wear. Pt particles (50–400 nm large) within the ash indicate that the diesel oxidation catalyst (DOC) upstream of the DPF shows aging effects. Radial cracks on the coating layer of the DOC confirm this assumption. The B100-DPF contains significantly less soot than B20 and B0. Based on the generally accepted view that soot reactivity correlates with the nanostructure of its primary particles, the length and curvature of graphene sheets from biofuel- and diesel-derived soot were measured and computed on the basis of HRTEM images. The results show that biofuel-derived soot can be more easily oxidized than diesel soot, not only during early formation but also during and after considerable particle growth. Differences in the graphene sheet separation distance, degree of crystalline order and size of primary soot particles between the two fuel types are in line with this inference.

  6. The role of residence time in diagnostic models of global carbon storage capacity: model decomposition based on a traceable scheme.

    Science.gov (United States)

    Yizhao, Chen; Jianyang, Xia; Zhengguo, Sun; Jianlong, Li; Yiqi, Luo; Chengcheng, Gang; Zhaoqi, Wang

    2015-11-06

    As a key factor that determines carbon storage capacity, residence time (τE) is not well constrained in terrestrial biosphere models. This factor is recognized as an important source of model uncertainty. In this study, to understand how τE influences terrestrial carbon storage prediction in diagnostic models, we introduced a model decomposition scheme in the Boreal Ecosystem Productivity Simulator (BEPS) and then compared it with a prognostic model. The result showed that τE ranged from 32.7 to 158.2 years. The baseline residence time (τ'E) was stable for each biome, ranging from 12 to 53.7 years for forest biomes and 4.2 to 5.3 years for non-forest biomes. The spatiotemporal variations in τE were mainly determined by the environmental scalar (ξ). By comparing models, we found that the BEPS uses a more detailed pool construction but rougher parameterization for carbon allocation and decomposition. With respect to ξ comparison, the global difference in the temperature scalar (ξt) averaged 0.045, whereas the moisture scalar (ξw) had a much larger variation, with an average of 0.312. We propose that further evaluations and improvements in τ'E and ξw predictions are essential to reduce the uncertainties in predicting carbon storage by the BEPS and similar diagnostic models.

  7. Sewage sludge ash to phosphate fertilizer by chlorination and thermal treatment: residence time requirements for heavy metal removal.

    Science.gov (United States)

    Nowak, Benedikt; Wegerer, Harald; Aschenbrenner, Philipp; Rechberger, Helmut; Winter, Franz

    2012-01-01

    Heavy metal removal from sewage sludge ash can be performed by mixing the ash with environmentally compatible chlorides (e.g. CaCl2 or MgCl2) and water, pelletizing the mixture and treating the pellets in a rotary reactor at about 1000 degrees C. Thermogravimetry-mass spectroscopy, muffle oven tests (500-1150 degrees C) and investigations in a laboratory-scale rotary reactor (950-1050 degrees C, residence time 1-25 min) were carried out. In the rotary reactor, up to 97% of Cu, 95% Pb and 95% Zn can be removed at 1050 degrees C. As Cl release starts from 400 degrees C (obtained from thermogravimetry-mass spectrometry experiments), heavy metals are already removed partially within the heating period. This heavy metal removal can be described as being similar to a first-order rate law. To meet the limit values specified in the Austrian and German fertilizer ordinances, residence times of the order of minutes are sufficient at 950 degrees C.

  8. Radiotracer investigation on the measurement of residence time distribution in an ethyl acetate reactor system with a large recycle ratio.

    Science.gov (United States)

    Datta, Arghya; Kumar Gupta, Raj; Goswami, Sunil; Kumar Sharma, Vijay; Bhunia, Haripada; Singh, Damandeep; Jagat Pant, Harish

    2017-12-01

    A radiotracer investigation was carried out on the measurement of residence time distribution (RTD) of process fluid in an industrial-scale ethyl acetate reactor system, which consists of two independent reactors with recirculation and connected in series with each other. Bromine-82 as ammonium bromide was used as the radiotracer for the RTD experiments at different operating conditions. The individual reactors and the overall reactor system were modelled using physically representative phenomenological models comprising of continuously stirred tank reactors (CSTRs). The results showed that the recirculation rate considerably affected the flow mixing behaviour and mean residence time of the process fluid in the reactor system. The results also showed that there was bypassing of the fluid in the first reactor that ranged from 12% to 22% and 40% dead volume at different operating conditions, whereas the second reactor behaved closely as an ideal CSTR. The results of the investigation can be used to optimise the process parameters and design new improved reactor systems for the production of ethyl acetate. Copyright © 2017 Elsevier Ltd. All rights reserved.

  9. The role of residence time in diagnostic models of global carbon storage capacity: model decomposition based on a traceable scheme

    Science.gov (United States)

    Yizhao, Chen; Jianyang, Xia; Zhengguo, Sun; Jianlong, Li; Yiqi, Luo; Chengcheng, Gang; Zhaoqi, Wang

    2015-01-01

    As a key factor that determines carbon storage capacity, residence time (τE) is not well constrained in terrestrial biosphere models. This factor is recognized as an important source of model uncertainty. In this study, to understand how τE influences terrestrial carbon storage prediction in diagnostic models, we introduced a model decomposition scheme in the Boreal Ecosystem Productivity Simulator (BEPS) and then compared it with a prognostic model. The result showed that τE ranged from 32.7 to 158.2 years. The baseline residence time (τ′E) was stable for each biome, ranging from 12 to 53.7 years for forest biomes and 4.2 to 5.3 years for non-forest biomes. The spatiotemporal variations in τE were mainly determined by the environmental scalar (ξ). By comparing models, we found that the BEPS uses a more detailed pool construction but rougher parameterization for carbon allocation and decomposition. With respect to ξ comparison, the global difference in the temperature scalar (ξt) averaged 0.045, whereas the moisture scalar (ξw) had a much larger variation, with an average of 0.312. We propose that further evaluations and improvements in τ′E and ξw predictions are essential to reduce the uncertainties in predicting carbon storage by the BEPS and similar diagnostic models. PMID:26541245

  10. Soot Superaggregates from Flaming Wildfires and Their Direct Radiative Forcing

    Science.gov (United States)

    Chakrabarty, Rajan K.; Beres, Nicholas D.; Moosmuller,Hans; China, Swarup; Mazzoleni, Claudio; Dubey, Manvendra K.; Liu, Li; Mishchenko, Michael I.

    2014-01-01

    Wildfires contribute significantly to global soot emissions, yet their aerosol formation mechanisms and resulting particle properties are poorly understood and parameterized in climate models. The conventional view holds that soot is formed via the cluster-dilute aggregation mechanism in wildfires and emitted as aggregates with fractal dimension D(sub f) approximately equals 1.8 mobility diameter D(sub m) (is) less than or equal to 1 micron, and aerodynamic diameter D(sub a) (is) less than or equal to 300 nm. Here we report the ubiquitous presence of soot superaggregates (SAs) in the outflow from a major wildfire in India. SAs are porous, low-density aggregates of cluster-dilute aggregates with characteristic D(sub f) approximately equals 2.6,D(sub m) (is) greater than 1 micron, and D(sub a) is less than or equal to 300 nm that form via the cluster-dense aggregation mechanism.We present additional observations of soot SAs in wildfire smoke-laden air masses over Northern California, New Mexico, and Mexico City. We estimate that SAs contribute, per unit optical depth, up to 35% less atmospheric warming than freshly-emitted (D(sub f) approximately equals 1.8) aggregates, and approximately equals 90% more warming than the volume-equivalent spherical soot particles simulated in climate models.

  11. How Entrustment Is Informed by Holistic Judgments Across Time in a Family Medicine Residency Program: An Ethnographic Nonparticipant Observational Study

    NARCIS (Netherlands)

    Sagasser, M.H.; Fluit, C.R.M.G.; Weel, C. van; Vleuten, C.P.M. van der; Kramer, A.W.M.

    2017-01-01

    PURPOSE: Entrustment has mainly been conceptualized as delegating discrete professional tasks. Because residents provide most of their patient care independently, not all resident performance is visible to supervisors; the entrustment process involves more than granting discrete tasks. This study

  12. Diesel soot aging in urban plumes within hours under cold dark and humid conditions.

    Science.gov (United States)

    Eriksson, A C; Wittbom, C; Roldin, P; Sporre, M; Öström, E; Nilsson, P; Martinsson, J; Rissler, J; Nordin, E Z; Svenningsson, B; Pagels, J; Swietlicki, E

    2017-09-28

    Fresh and aged diesel soot particles have different impacts on climate and human health. While fresh diesel soot particles are highly aspherical and non-hygroscopic, aged particles are spherical and hygroscopic. Aging and its effect on water uptake also controls the dispersion of diesel soot in the atmosphere. Understanding the timescales on which diesel soot ages in the atmosphere is thus important, yet knowledge thereof is lacking. We show that under cold, dark and humid conditions the atmospheric transformation from fresh to aged soot occurs on a timescale of less than five hours. Under dry conditions in the laboratory, diesel soot transformation is much less efficient. While photochemistry drives soot aging, our data show it is not always a limiting factor. Field observations together with aerosol process model simulations show that the rapid ambient diesel soot aging in urban plumes is caused by coupled ammonium nitrate formation and water uptake.

  13. Foraging strategy of a Neotropical primate: how intrinsic and extrinsic factors influence destination and residence time

    DEFF Research Database (Denmark)

    Plante, Sabrina; Colchero, Fernando; Calmé, Sophie

    2014-01-01

    accounting for intrinsic and extrinsic factors, which are often overlooked when modelling foraging behaviour. 2.We identified the decision rules for foraging in black howler monkeys (Alouatta pigra), according to food preferences, locations of high quality patches and previously eaten trees, phenology...... of food resources and hunger state. We depicted foraging in two stages: 1) the choice of the immediate next tree and 2) the time spent on this tree. We used a recently developed model for inference of movement processes, incorporating resource selection functions into a Markov Chain framework. 3.We found....... Time spent on a tree was positively and strongly affected by the presence of preferred food items, but not by its species. We also showed that time spent on trees increased as a function of satiation state. We suggest that the strategy adopted by black howlers tends to be efficient because choosing...

  14. A decade of robot-assisted radical prostatectomy training: Time-based metrics and qualitative grading for fellows and residents.

    Science.gov (United States)

    Altok, Muammer; Achim, Mary F; Matin, Surena F; Pettaway, Curtis A; Chapin, Brian F; Davis, John W

    2018-01-01

    As modern urology residency and fellowship training in robot-assisted surgery evolves toward standardized curricula (didactics, dry/wet-laboratory exercises, and surgical assistance), additional tools are needed to evaluate on-console performance. At the start of our robotics program in 2006, we set-up a time- and quality-based evaluation program and aim to consolidate this data into a simple set of metrics for self-evaluation. Using our index procedure of robot-assisted radical prostatectomy (RARP), we prospectively collected data on 2,215 cases over 10 years from 6 faculty surgeons and 94 trainees (43 urologic oncology fellows and 51 urology residents). The steps of the operation were divided into 11 consistent steps, and the metrics included time to completion and quality using a 6-level grading system. Time metrics were consolidated into quartiles for benchmarking. The median times for trainees to complete each step were 15% to 120% higher than those of the staff (Pstaff results. Steps performed by trainees were carefully chosen for a high success rate, and on our Likert-like scale were graded 4 to 5 in more than 95% of cases. There were no grade 0 (very poor) cases, and grades 1 (multiple technical errors) and 2 (could not be completed but without safety issues) were rare (staff. As a trainee progress through a rotation, these benchmarks can assist in prioritizing the need for more attention to a basic step vs. progression to more advanced steps. Copyright © 2018 Elsevier Inc. All rights reserved.

  15. Laser-induced incandescence: Towards quantitative soot volume fraction measurements

    Energy Technology Data Exchange (ETDEWEB)

    Tzannis, A.P.; Wienbeucker, F.; Beaud, P.; Frey, H.-M.; Gerber, T.; Mischler, B.; Radi, P.P. [Paul Scherrer Inst. (PSI), Villigen (Switzerland)

    1999-08-01

    Laser-Induced Incandescence has recently emerged as a versatile tool for measuring soot volume fraction in a wide range of combustion systems. In this work we investigate the essential features of the method. LII is based on the acquisition of the incandescence of soot when heated through a high power laser pulse. Initial experiments have been performed on a model laboratory flame. The behaviour of the LII signal is studied experimentally. By applying numerical calculations we investigate the possibility to obtain two-dimensional soot volume fraction distributions. For this purpose a combination of LII with other techniques is required. This part is discussed in some extent and the future work is outlined. (author) 4 figs., 3 refs.

  16. Mean residence time of kaolinite and smectite-bound organic matter in mozambiquan soils

    NARCIS (Netherlands)

    Wattel-Koekkoek, E.J.W.; Buurman, P.

    2004-01-01

    To gain understanding about the process of global warming, it is essential to study the global C cycle. In the global C cycle, soil organic matter (SOM) is a major source and sink of atmospheric C. Turnover times of C in these soil organic compounds vary from hours to thousands of years. Clay

  17. Estimation of U.S. sewer residence time distributions for national-scale risk assessment of down-the-drain chemicals.

    Science.gov (United States)

    Kapo, Katherine E; Paschka, Michael; Vamshi, Raghu; Sebasky, Megan; McDonough, Kathleen

    2017-12-15

    Sewer residence time (the amount of time a given volume of wastewater resides in a sewer system prior to treatment) can have a significant influence on predictions of environmental fate and transport of wastewater constituents and corresponding risk assessment. In this study, a geographic information systems-based approach for estimating the distribution of sewer residence times for the U.S. was developed using road networks as a spatial proxy for sewer networks. The suitability of the approach was evaluated using case study municipalities, and the approach was subsequently extrapolated to 3422 wastewater treatment facilities of varying size across the U.S. to estimate a national distribution of sewer residence times. The estimated national median residence time for the U.S. was 3.3h. Facilities serving smaller municipalities (residence times to facilities serving larger municipalities, though the latter comprise a greater proportion of overall national wastewater volume. The results of this study provide an important data resource in combination with chemical in-sewer biodegradation data to enable probabilistic risk assessment of consumer product chemicals disposed of down the drain. Copyright © 2017 Elsevier B.V. All rights reserved.

  18. Effect of lubricant additives on the prowear characteristics of synthetic diesel soots

    Energy Technology Data Exchange (ETDEWEB)

    Rounds, F.G.

    1986-01-01

    Soot in the crankcase of diesel engines promotes wear. The theory is that this soot preferentially adsorbs the active antiwear species, probably a zinc dithiophosphate (ZDP) decomposition product, before the protective antiwear surface coating can be formed on the rubbing surfaces. Previous studies indicated that the prowear characteristics of diesel soot depend on the engine operating conditions and the lubricant used. This observation suggested that, by properly formulating the oil, the adverse effects of the soot might be minimized.

  19. Ice Formation by Soot-Containing Aerosol Particles

    Science.gov (United States)

    Demott, P. J.; Petters, M. D.; Prenni, A. J.; Kreidenweis, S. M.; Carrico, C. M.; Bennett, M. R.; Stanglmaier, R.; Volckens, J.; Popovicheva, O. B.

    2006-12-01

    A role for soot particles as atmospheric ice forming nuclei remains highly uncertain and poorly quantified. A relatively small amount of data exists and most of this is for laboratory surrogates that may not be well characterized or of assured relevance to the atmosphere. It is important to constrain the role of soot particles as ice nuclei due to their abundance in the atmosphere and the large contribution from anthropogenic activities. Further, global climate models are beginning to be capable of treating the impact of different aerosol types, including soot particles. This paper reports on studies of ice formation by or within surrogates for hydrophobic soot and realistic carbonaceous particles from combustion of fuel in a diesel engine, burning of an assortment biomass materials, and real jet fuel combustor particles. Measurements of primarily monodisperse particles were focused below -30°C to emphasize the transition between temperatures where heterogeneous ice nucleation is required for ice formation and those for which homogeneous freezing processes are also possible. Ice nucleation measurements were made with a continuous flow diffusion chamber. Simultaneous measurements of hygroscopic water uptake and cloud condensation nucleation behavior were also made at 30°C for each aerosol type. Small fractions of hydrophobic soot particles are found capable of initiating heterogeneous ice formation at low temperatures. Results of studies of more realistic particles suggest that any process that increases hygroscopicity tends to limit the conditions for ice formation within soot particles. Most biomass burning particles, showing a range of dry/wet diameter hygroscopic growth factors (1.03 activity as CCN to 102% RH, yet behaved as particles containing solutions in which homogeneous freezing was supported at temperatures below -38°C. This is tentatively attributed to condensation of semi-volatiles during cooling. Ice forming ability as warm as -30°C was limited to

  20. Groundwater residence times in Shenandoah National Park, Blue Ridge Mountains, Virginia, USA: A multi-tracer approach

    Science.gov (United States)

    Plummer, Niel; Busenberg, E.; Böhlke, J.K.; Nelms, D.L.; Michel, R.L.; Schlosser, P.

    2001-01-01

    Chemical and isotopic properties of water discharging from springs and wells in Shenandoah National Park (SNP), near the crest of the Blue Ridge Mountains, VA, USA were monitored to obtain information on groundwater residence times. Investigated time scales included seasonal (wet season, April, 1996; dry season, August–September, 1997), monthly (March through September, 1999) and hourly (30-min interval recording of specific conductance and temperature, March, 1999 through February, 2000). Multiple environmental tracers, including tritium/helium-3 (3H/3He), chlorofluorocarbons (CFCs), sulfur hexafluoride (SF6), sulfur-35 (35S), and stable isotopes (δ18O and δ2H) of water, were used to estimate the residence times of shallow groundwater discharging from 34 springs and 15 wells. The most reliable ages of water from springs appear to be based on SF6 and 3H/3He, with most ages in the range of 0–3 years. This range is consistent with apparent ages estimated from concentrations of CFCs; however, CFC-based ages have large uncertainties owing to the post-1995 leveling-off of the CFC atmospheric growth curves. Somewhat higher apparent ages are indicated by 35S (>1.5 years) and seasonal variation of δ18O (mean residence time of 5 years) for spring discharge. The higher ages indicated by the 35S and δ18O data reflect travel times through the unsaturated zone and, in the case of 35S, possible sorption and exchange of S with soils or biomass. In springs sampled in April, 1996, apparent ages derived from the 3H/3He data (median age of 0.2 years) are lower than those obtained from SF6 (median age of 4.3 years), and in contrast to median ages from 3H/3He (0.3 years) and SF6 (0.7 years) obtained during the late summer dry season of 1997. Monthly samples from 1999 at four springs in SNP had SF6apparent ages of only 1.2 to 2.5±0.8 years, and were consistent with the 1997 SF6 data. Water from springs has low excess air (0–1 cm3 kg−1) and N2–Ar temperatures that vary

  1. Batch leachate treatment using stirred electrocoagulation reactor with variation of residence time and stirring rate

    Science.gov (United States)

    Sitorus, I. S.; Astono, W.; Iswanto, B.

    2018-01-01

    This study aims to reduce pollutant levels of the leachate by electrocoagulation method using a stirred electrocoagulation reactor as the electrochemical water treatment. The release of active coagulants as metallic ions took place in the anode, while in the cathode, the electrolysis reaction in the form of hydrogen gas dischargeoccurred. The source of wastewater is Waste Water Treatment Plant inlet III of Bantar Gebang, Bekasi. Some parameters were analyzed in this research, i.e., Chemical Oxygen Demand (COD), Biochemical Oxygen Demand (BOD), NH3, NO3 -, NO2 -, N-total, and organic substances as well as the microorganism growth before and after electrocoagulation, with variations of detention time (seconds) of 10, 20, 120, 600 and rapid mixing conditions (rpm) of 60, 100 and 200. The results show that the greater the rapid mixing speed and the detention time of electrolysis, the higher the removal of contaminants in liquid waste. The optimum condition of electrocoagulation was encountered at 200 rpm rapid mixing with 600 seconds of processing time. The removal efficiencies of electrocoagulation method for each parameter are TSS of 46.80%, BOD5 of 71.33%, COD of 73.77%, Pb of 62.5%,and NH3-N of 57.92%,whereas the pH value has been increased from 8.03 to 8.95. The electrocoagulation method can reduce levels of pollutants, complying with the environmental standards.

  2. Particle (Soot) Pollution in Port Harcourt Rivers State, Nigeria—Double Air Pollution Burden? Understanding and Tackling Potential Environmental Public Health Impacts

    OpenAIRE

    Okhumode H. Yakubu

    2017-01-01

    Residents of Port Harcourt in Rivers State, Nigeria, and its environs have since the last quarter of 2016 been experiencing adverse environmental impacts of particle (soot) pollution. This “double air pollution burden”—the unresolved prevailing widespread air pollution and the “added” emergence of particle pollution considered an environmental health threat, led to protests against government inaction in some parts of the state. In February 2017, several months following the onset of the poll...

  3. Can we differentiate alpine groundwater storages regarding volume and residence time by recession observations, ion composition and tracer balance?

    Science.gov (United States)

    Floriancic, Marius; Smoorenburg, Maarten; Margreth, Michael; Naef, Felix

    2015-04-01

    Research on how catchments store and release water is essential to improve flood and low flow prediction in (un)gauged watersheds. Despite their importance for catchment scale assessments on runoff generation, knowledge on storage properties and residence times is still limited. Here we present some approaches to separate different storage types regarding their residence time and a quantification of the volumes of these storages based on a dataset of winter recession observation in the alpine Poschiavino headwater area. This spatially highly resolved dataset of discharge, electric conductivity and ion composition from a watershed with strongly contrasting storage properties, allowed separating three main contributing sources: continuous discharge from bedrock cracks, strongly delayed discharge from thick sediment deposits and fractured rock and rapid discharge from shallow layers. The gradients of the recession curves, the variation of electric conductivity in the river network and calculated tracer balance were used to separate contribution from different sources. Additionally contribution from sedimentary rocks and crystalline layers could be separated based on the variation of ion composition in the water samples. We derived recession curves for a period of four months for the separated storages in different parts of the catchment allowing estimation of the contributed volumes in this time period. Finally the spatial distribution of the storage types could be mapped throughout the catchment based on information like geo(morpho)logical maps, aerial photographs, DEM and field observations. We found significant variation comparing the discharged volume and specific discharge throughout the winter season in the different subcatchments. Constant discharge from bedrock cracks is similar in all catchment parts. Storage in the shallow deposits depleted quickly. High winter discharge could be attributed to thick quaternary deposits contributing during the whole

  4. New Nanotech from an Ancient Material: Chemistry Demonstrations Involving Carbon-Based Soot

    Science.gov (United States)

    Campbell, Dean J.; Andrews, Mark J.; Stevenson, Keith J.

    2012-01-01

    Carbon soot has been known since antiquity, but has recently been finding new uses as a robust, inexpensive nanomaterial. This paper describes the superhydrophobic properties of carbon soot films prepared by combustion of candle wax or propane gas and introduces some of the optical absorption and fluorescence properties of carbon soot particles.…

  5. Effects of dicarboxylic acid coating on the optical properties of soot.

    Science.gov (United States)

    Xue, Huaxin; Khalizov, Alexei F; Wang, Lin; Zheng, Jun; Zhang, Renyi

    2009-09-28

    Soot is a major component of atmospheric aerosols responsible for absorption of visible solar radiation. Internal mixing of soot with transparent materials can enhance its ability to absorb and scatter light, resulting in a larger role of soot in climate forcing. We have investigated the absorption and scattering of visible light (532 nm) by soot aerosol internally mixed with succinic and glutaric acids using a combination of a cavity ring-down spectrometer and an integrating nephelometer. The measurements were performed for flame-generated soot aerosol with well-characterized morphology and mixing state in the particle size range from 155 to 320 nm. Thin coatings of dicarboxylic acids on soot aggregates (with a mass fraction of 0.1-0.4) enhance significantly light scattering (up to 3.8 fold) and slightly light absorption (less than 1.2 fold). Cycling the coated soot aerosol through high relative humidity (humidified to 90% RH and then dried to 5% RH) promotes further increase in light absorption and scattering for soot internally mixed with glutaric acid, but not for soot mixed with succinic acid. The larger effect of glutaric acid on light absorption and scattering is caused by the irreversible restructuring of soot aggregates induced by the coating material. Our results indicate that the enhancement in the optical properties of soot by transparent coatings is strongly related to the ability of the coating materials to change the morphology of soot aggregates.

  6. Use of the QR Reader to Provide Real-Time Evaluation of Residents' Skills Following Surgical Procedures.

    Science.gov (United States)

    Reynolds, Kellin; Barnhill, Danny; Sias, Jamie; Young, Amy; Polite, Florencia Greer

    2014-12-01

    A portable electronic method of providing instructional feedback and recording an evaluation of resident competency immediately following surgical procedures has not previously been documented in obstetrics and gynecology. This report presents a unique electronic format that documents resident competency and encourages verbal communication between faculty and residents immediately following operative procedures. The Microsoft Tag system and SurveyMonkey platform were linked by a 2-D QR code using Microsoft QR code generator. Each resident was given a unique code (TAG) embedded onto an ID card. An evaluation form was attached to each resident's file in SurveyMonkey. Postoperatively, supervising faculty scanned the resident's TAG with a smartphone and completed the brief evaluation using the phone's screen. The evaluation was reviewed with the resident and automatically submitted to the resident's educational file. The evaluation system was quickly accepted by residents and faculty. Of 43 residents and faculty in the study, 38 (88%) responded to a survey 8 weeks after institution of the electronic evaluation system. Thirty (79%) of the 38 indicated it was superior to the previously used handwritten format. The electronic system demonstrated improved utilization compared with paper evaluations, with a mean of 23 electronic evaluations submitted per resident during a 6-month period versus 14 paper assessments per resident during an earlier period of 6 months. This streamlined portable electronic evaluation is an effective tool for direct, formative feedback for residents, and it creates a longitudinal record of resident progress. Satisfaction with, and use of, this evaluation system was high.

  7. Linear and Nonlinear Time-Frequency Analysis for Parameter Estimation of Resident Space Objects

    Science.gov (United States)

    2017-02-22

    technical report is organised as follows: • In Section 2 Time-Frequency transforms are discussed and parameters of interests are identified. • In Section...NRMSE 0,206 0,292 0,428 %NRMSE 0,375 0,405 0,501 Table 5: table 4 continued The worst behaviour is obtained in the case of RSO 2. The reason behind...quantisation effect. On the other hand, the best behaviour is produced by RSO 1, whose Doppler frequency is the highest. By looking at tables 4 and 5, and not

  8. Modelling soot formation from wall films in a gasoline direct injection engine using a detailed population balance model

    International Nuclear Information System (INIS)

    Wang, Buyu; Mosbach, Sebastian; Schmutzhard, Sebastian; Shuai, Shijin; Huang, Yaqing; Kraft, Markus

    2016-01-01

    Highlights: • Soot formation from a wall film in a GDI engine is simulated. • Spray impingement and wall film evaporation models are added to SRM Engine Suite. • Soot is modelled using a highly detailed population balance model. • Particle size distributions are measured experimentally. • Evolution of wall region is shown in equivalence ratio-temperature diagrams. - Abstract: In this study, soot formation in a Gasoline Direct Injection (GDI) engine is simulated using a Stochastic Reactor Model (SRM Engine Suite) which contains a detailed population balance soot model capable of describing particle morphology and chemical composition. In order to describe the soot formation originating from the wall film, the SRM Engine Suite is extended to include spray impingement and wall film evaporation models. The cylinder is divided into a wall and a bulk zone to resolve the equivalence ratio and temperature distributions of the mixture near the wall. The combustion chamber wall is assumed to exchange heat directly only with the wall zone. The turbulent mixing within each zone and between the two zones are simulated with different mixing models. The effects of key parameters on the temperature and equivalence ratio in the two zones are investigated. The mixing rate between the wall and bulk zone has a significant effect on the wall zone, whilst the mixing rate in the wall zone only has a negligible impact on the temperature and equivalence ratio below a certain threshold. Experimental data are obtained from a four-cylinder, gasoline-fuelled direct injection spark ignition engine operated stoichiometrically. An injection timing sweep, ranging from 120 CAD BTDC to 330 CAD BTDC, is conducted in order to investigate the effect of spray impingement on soot formation. The earliest injection case (330 CAD BTDC), which produces significantly higher levels of particle emissions than any other case, is simulated by the current model. It is found that the in-cylinder pressure

  9. Recovery of Sleep or Recovery of Self? A Grounded Theory Study of Residents' Decision Making Regarding How to Spend Their Nonclinical Postcall Time.

    Science.gov (United States)

    Taylor, Taryn S; Nisker, Jeff; Teunissen, Pim W; Dornan, Tim; Lingard, Lorelei

    2016-03-01

    As resident work hours policies evolve, residents' off-duty time remains poorly understood. Despite assumptions about how residents should be using their postcall, off-duty time, there is little research on how residents actually use this time and the reasoning underpinning their activities. This study sought to understand residents' nonclinical postcall activities when they leave the hospital, their decision-making processes, and their perspectives on the relationship between these activities and their well-being or recovery. The study took place at a Liaison Committee on Medical Education-accredited Canadian medical school from 2012 to 2014. The authors recruited a purposive and convenience sample of postgraduate year 1-5 residents from six surgical and nonsurgical specialties at three hospitals affiliated with the medical school. Using a constructivist grounded theory approach, semistructured interviews were conducted, audio-taped, transcribed, anonymized, and combined with field notes. The authors analyzed interview transcripts using constant comparative analysis and performed post hoc member checking. Twenty-four residents participated. Residents characterized their predominant approach to postcall decision making as one of making trade-offs between multiple, competing, seemingly incompatible, but equally valuable, activities. Participants exhibited two different trade-off orientations: being oriented toward maintaining a normal life or toward mitigating fatigue. The authors' findings on residents' trade-off orientations suggest a dual recovery model with postcall trade-offs motivated by the recovery of sleep or of self. This model challenges the dominant viewpoint in the current duty hours literature and suggests that the duty hours discussion must be broadened to include other recovery processes.

  10. Time course of cesium radionuclides body burden in residents of regions with elevated background radiation

    International Nuclear Information System (INIS)

    Vasil'ev, V.N.; Luchkov, A.B.; Trushin, V.I.; Khazins, E.D.

    1990-01-01

    The authors represent summarized data on the time course of 134 Cs and 137 Cs body burden in the population of the Krasnogorsky District of the Bryansk Region (Byelorussian SSR) over the period of June 1986-Jule 1989. A RISh-5M was used as a whole-body counter, its performance and calibration methods were described. A retrospective analysis has shown that the main accumulation of radionuclides occurred before May 15 1986. The highest half-life noted from August 1986 till Februal 1987. The ratio of accumulated Cs in children and adults was 0.3, in men and women - 1.4. The effectiveness of measures aimed at reducing collective doses of internal irradiation was analyzed

  11. Changing restoration rules: exotic bivalves interact with residence time and depth to control phytoplankton productivity

    Science.gov (United States)

    Lucas, Lisa V.; Thompson, Janet K.

    2012-01-01

    Non-native species are a prevalent ecosystem stressor that can interact with other stressors to confound resource management and restoration. We examine how interactions between physical habitat attributes and a particular category of non-native species (invasive bivalves) influence primary production in aquatic ecosystems. Using mathematical models, we show how intuitive relationships between phytoplankton productivity and controllable physical factors (water depth, hydraulic transport time) that hold in the absence of bivalves can be complicated—and even reversed—by rapid bivalve grazing. In light-limited environments without bivalves, shallow, hydrodynamically “slow” habitats should generally have greater phytoplankton biomass and productivity than deeper, “faster” habitats. But shallower, slower environments can be less productive than deeper, faster ones if benthic grazing is strong. Moreover, shallower and slower waters exhibit a particularly broad range of possible productivity outcomes that can depend on whether bivalves are present. Since it is difficult to predict the response of non-native bivalves to habitat restoration, outcomes for new shallow, slow environments can be highly uncertain. Habitat depth and transport time should therefore not be used as indicators of phytoplankton biomass and production where bivalve colonization is possible. This study provides for ecosystem management a particular example of a broad lesson: abiotic ecosystem stressors should be managed with explicit consideration of interactions with other major (including biotic) stressors. We discuss the applicability and management implications of our models and results for a range of aquatic system types, with a case study focused on the Sacramento-San Joaquin Delta (California, USA). Simple mathematical models like those used here can illuminate interactions between ecosystem stressors and provide process-based guidance for resource managers as they develop strategies

  12. Polymer binding to carbon nanotubes in aqueous dispersions: residence time on the nanotube surface as obtained by NMR diffusometry.

    Science.gov (United States)

    Frise, Anton E; Pagès, Guilhem; Shtein, Michael; Pri Bar, Ilan; Regev, Oren; Furó, István

    2012-03-08

    The binding of block copolymer Pluronic F-127 in aqueous dispersions of single- (SWCNT) and multiwalled (MWCNT) carbon nanotubes has been studied by pulsed-field-gradient (PFG) (1)H NMR spectroscopy. We show that a major fraction of polymers exist as a free species while a minor fraction is bound to the carbon nanotubes (CNT). The polymers exchange between these two states with residence times on the nanotube surface of 24 ± 5 ms for SWCNT and of 54 ± 11 ms for MWCNT. The CNT concentration in the solution was determined by improved thermal gravimetric analysis (TGA) indicating that the concentration of SWCNT dispersed by F-127 was significantly higher than that for MWCNT. For SWCNT, the area per adsorbed Pluronic F-127 molecule is estimated to be about 40 nm(2).

  13. Comparison of groundwater residence time using isotope techniques and numerical groundwater flow model in Gneissic Terrain, Korea

    International Nuclear Information System (INIS)

    Bae, D.S.; Kim, C.S.; Koh, Y.K.; Kim, K.S.; Song, M.Y.

    1997-01-01

    The prediction of groundwater flow affecting the migration of radionuclides is an important component of the performance assessment of radioactive waste disposal. Groundwater flow in fractured rock mass is controlled by fracture networks, transmissivity and hydraulic gradient. Furthermore the scale-dependent and anisotropic properties of hydraulic parameters are resulted mainly from irregular patterns of fracture system, which are very complex to evaluate properly with the current techniques available. For the purpose of characterizing a groundwater flow in fractured rock mass, the discrete fracture network (DFN) concept is available on the basis of assumptions of groundwater flowing only along fractures and flowpaths in rock mass formed by interconnected fractures. To increase the reliability of assessment in groundwater flow phenomena, numerical groundwater flow model and isotopic techniques were applied. Fracture mapping, borehole acoustic scanning were performed to identify conductive fractures in gneissic terrane. Tracer techniques, using deuterium, oxygen-18 and tritium were applied to evaluate the recharge area and groundwater residence time

  14. Intake condition requirements for biodiesel modulated kinetic combustion concept to achieve a simultaneous NOx and soot removal

    International Nuclear Information System (INIS)

    Kim, Keunsoo; Oh, Seungmook; Lee, Yonggyu; Lee, Sunyoup; Kim, Junghwan

    2015-01-01

    Highlights: • MK LTC combustion was investigated under various intake conditions. • BD20 MK combustion achieved NO x and soot removal at achievable intake conditions. • The BD20 best point showed lower ISFC and COV IMEP than the diesel best point. • Higher intake pressure showed higher efficiency at all intake oxygen concentrations. • Simultaneous NO x and soot removal required 200 kPa intake pressure at a medium load. - Abstract: The fuel oxygen contained in oxygenated fuels can help reduce harmful engine-out emissions and improve the combustion process in compression-ignition engines. The use of soybean methylene ether biodiesel in the low-temperature combustion (LTC) regime has the potential to suppress soot formation and nitrogen oxides (NO x ) emissions even further, which eventually alleviates the burden of the after-treatment system. In the present study, the effects of the intake pressure and injection timing on the combustion and emissions of the modulated kinetic (MK) combustion concept with ultra-low sulfur diesel and 20% biodiesel blended fuel (BD20) were investigated in a single-cylinder CI engine. The intake pressure was varied from 100 kPa to 250 kPa for the intake oxygen concentration range of 11–17%. The engine test results indicate that simultaneous reductions in both the NO x and soot emissions were realized under the MK LTC combustion regime. At the best operating point, BD20 achieved the simultaneous NO x and soot removal at a lower intake pressure and lower EGR level than diesel, which led to better fuel economy. In addition, BD20 achieved acceptable levels of combustion stability and noise level

  15. Effects of non-unity Lewis number of gas-phase species in turbulent nonpremixed sooting flames

    KAUST Repository

    Attili, Antonio

    2016-02-13

    Turbulence statistics from two three-dimensional direct numerical simulations of planar n-heptane/air turbulent jets are compared to assess the effect of the gas-phase species diffusion model on flame dynamics and soot formation. The Reynolds number based on the initial jet width and velocity is around 15, 000, corresponding to a Taylor scale Reynolds number in the range 100 ≤ Reλ ≤ 150. In one simulation, multicomponent transport based on a mixture-averaged approach is employed, while in the other the gas-phase species Lewis numbers are set equal to unity. The statistics of temperature and major species obtained with the mixture-averaged formulation are very similar to those in the unity Lewis number case. In both cases, the statistics of temperature are captured with remarkable accuracy by a laminar flamelet model with unity Lewis numbers. On the contrary, a flamelet with a mixture-averaged diffusion model, which corresponds to the model used in the multi-component diffusion three-dimensional DNS, produces significant differences with respect to the DNS results. The total mass of soot precursors decreases by 20-30% with the unity Lewis number approximation, and their distribution is more homogeneous in space and time. Due to the non-linearity of the soot growth rate with respect to the precursors\\' concentration, the soot mass yield decreases by a factor of two. Being strongly affected by coagulation, soot number density is not altered significantly if the unity Lewis number model is used rather than the mixture-averaged diffusion. The dominant role of turbulent transport over differential diffusion effects is expected to become more pronounced for higher Reynolds numbers. © 2016 The Combustion Institute.

  16. Arctic tundra shrub invasion and soot deposition: Consequences for spring snowmelt and near-surface air temperatures

    Science.gov (United States)

    Strack, John E.; Pielke, Roger A.; Liston, Glen E.

    2007-12-01

    Invasive shrubs and soot pollution both have the potential to alter the surface energy balance and timing of snow melt in the Arctic. Shrubs reduce the amount of snow lost to sublimation on the tundra during the winter leading to a deeper end-of-winter snowpack. The shrubs also enhance the absorption of energy by the snowpack during the melt season by converting incoming solar radiation to longwave radiation and sensible heat. Soot deposition lowers the albedo of the snow, allowing it to more effectively absorb incoming solar radiation and thus melt faster. This study uses the Colorado State University Regional Atmospheric Modeling System version 4.4 (CSU-RAMS 4.4), equipped with an enhanced snow model, to investigate the effects of shrub encroachment and soot deposition on the atmosphere and snowpack in the Kuparuk Basin of Alaska during the May-June melt period. The results of the simulations suggest that a complete invasion of the tundra by shrubs leads to a 2.2°C warming of 3 m air temperatures and a 108 m increase in boundary layer depth during the melt period. The snow-free date also occurred 11 d earlier despite having a larger initial snowpack. The results also show that a decrease in the snow albedo of 0.1, owing to soot pollution, caused the snow-free date to occur 5 d earlier. The soot pollution caused a 1.0°C warming of 3 m air temperatures and a 25 m average deepening of the boundary layer.

  17. The effect of residence time on the tensile properties of superelastic and thermal activated Ni-Ti orthodontic wires

    Directory of Open Access Journals (Sweden)

    Kathia Maria Fosenca de Britto

    2011-09-01

    Full Text Available Since the 1980s, different devices based on superelastic alloys have been developed to fulfill orthodontic applications. Particularly in the last decades several researches have been carried out to evaluate the mechanical behavior of Ni-Ti alloys, including their tensile, torsion and fatigue properties. However, studies regarding the dependence of elastic properties on residence time of Ni-Ti wires in the oral cavity are scarce. Such approach is essential since metallic alloys are submitted to mechanical stresses during orthodontic treatment as well as pH and temperature fluctuations. The goal of the present contribution is to provide elastic stress-strain results to guide the orthodontic choice between martensitic thermal activated and austenitic superelastic Ni-Ti alloys. From the point of view of an orthodontist, the selection of appropriate materials and the correct maintenance of the orthodontic apparatus are essential needs during clinical treatment. The present work evaluated the elastic behavior of Ni-Ti alloy wires with diameters varying from 0.014 to 0.020 inches, submitted to hysteresis tensile tests with 8% strain. Tensile tests were performed after periods of use of 1, 2 and 3 months in the oral cavity of patients submitted to orthodontic treatment. The results from the hysteresis tests allowed to exam the strain range covered by isostress lines upon loading and unloading, as well as the residual strain after unloading for both superelastic and thermal activated Ni-Ti wires. Superelastic Ni-Ti wires exhibited higher load isostress values compared to thermal activated wires. It was found that such differences in the load isostress values can increase with increasing residence time.

  18. The decadal state of the terrestrial carbon cycle: Global retrievals of terrestrial carbon allocation, pools, and residence times.

    Science.gov (United States)

    Bloom, A Anthony; Exbrayat, Jean-François; van der Velde, Ivar R; Feng, Liang; Williams, Mathew

    2016-02-02

    The terrestrial carbon cycle is currently the least constrained component of the global carbon budget. Large uncertainties stem from a poor understanding of plant carbon allocation, stocks, residence times, and carbon use efficiency. Imposing observational constraints on the terrestrial carbon cycle and its processes is, therefore, necessary to better understand its current state and predict its future state. We combine a diagnostic ecosystem carbon model with satellite observations of leaf area and biomass (where and when available) and soil carbon data to retrieve the first global estimates, to our knowledge, of carbon cycle state and process variables at a 1° × 1° resolution; retrieved variables are independent from the plant functional type and steady-state paradigms. Our results reveal global emergent relationships in the spatial distribution of key carbon cycle states and processes. Live biomass and dead organic carbon residence times exhibit contrasting spatial features (r = 0.3). Allocation to structural carbon is highest in the wet tropics (85-88%) in contrast to higher latitudes (73-82%), where allocation shifts toward photosynthetic carbon. Carbon use efficiency is lowest (0.42-0.44) in the wet tropics. We find an emergent global correlation between retrievals of leaf mass per leaf area and leaf lifespan (r = 0.64-0.80) that matches independent trait studies. We show that conventional land cover types cannot adequately describe the spatial variability of key carbon states and processes (multiple correlation median = 0.41). This mismatch has strong implications for the prediction of terrestrial carbon dynamics, which are currently based on globally applied parameters linked to land cover or plant functional types.

  19. The decadal state of the terrestrial carbon cycle: Global retrievals of terrestrial carbon allocation, pools, and residence times

    Science.gov (United States)

    Bloom, A. Anthony; Exbrayat, Jean-François; van der Velde, Ivar R.; Feng, Liang; Williams, Mathew

    2016-01-01

    The terrestrial carbon cycle is currently the least constrained component of the global carbon budget. Large uncertainties stem from a poor understanding of plant carbon allocation, stocks, residence times, and carbon use efficiency. Imposing observational constraints on the terrestrial carbon cycle and its processes is, therefore, necessary to better understand its current state and predict its future state. We combine a diagnostic ecosystem carbon model with satellite observations of leaf area and biomass (where and when available) and soil carbon data to retrieve the first global estimates, to our knowledge, of carbon cycle state and process variables at a 1° × 1° resolution; retrieved variables are independent from the plant functional type and steady-state paradigms. Our results reveal global emergent relationships in the spatial distribution of key carbon cycle states and processes. Live biomass and dead organic carbon residence times exhibit contrasting spatial features (r = 0.3). Allocation to structural carbon is highest in the wet tropics (85–88%) in contrast to higher latitudes (73–82%), where allocation shifts toward photosynthetic carbon. Carbon use efficiency is lowest (0.42–0.44) in the wet tropics. We find an emergent global correlation between retrievals of leaf mass per leaf area and leaf lifespan (r = 0.64–0.80) that matches independent trait studies. We show that conventional land cover types cannot adequately describe the spatial variability of key carbon states and processes (multiple correlation median = 0.41). This mismatch has strong implications for the prediction of terrestrial carbon dynamics, which are currently based on globally applied parameters linked to land cover or plant functional types. PMID:26787856

  20. Water availability limits tree productivity, carbon stocks, and carbon residence time in mature forests across the western US

    Science.gov (United States)

    Berner, Logan T.; Law, Beverly E.; Hudiburg, Tara W.

    2017-01-01

    Water availability constrains the structure and function of terrestrial ecosystems and is projected to change in many parts of the world over the coming century. We quantified the response of tree net primary productivity (NPP), live biomass (BIO), and mean carbon residence time (CRT = BIO / NPP) to spatial variation in water availability in the western US. We used forest inventory measurements from 1953 mature stands (> 100 years) in Washington, Oregon, and California (WAORCA) along with satellite and climate data sets covering the western US. We summarized forest structure and function in both domains along a 400 cm yr-1 hydrologic gradient, quantified with a climate moisture index (CMI) based on the difference between precipitation and reference evapotranspiration summed over the water year (October-September) and then averaged annually from 1985 to 2014 (CMIwy). Median NPP, BIO, and CRT computed at 10 cm yr-1 intervals along the CMIwy gradient increased monotonically with increasing CMIwy across both WAORCA (rs = 0.93-0.96, p the western US (rs = 0.93-0.99, p the driest and wettest 5 % of sites, while BIO increased from 26 to 281 Mg C ha-1 and CRT increased from 11 to 49 years. The satellite data sets revealed similar changes over the western US, though these data sets tended to plateau in the wettest areas, suggesting that additional efforts are needed to better quantify NPP and BIO from satellites in high-productivity, high-biomass forests. Our results illustrate that long-term average water availability is a key environmental constraint on tree productivity, carbon storage, and carbon residence time in mature forests across the western US, underscoring the need to assess potential ecosystem response to projected warming and drying over the coming century.

  1. How does warming affect carbon allocation, respiration and residence time in trees? An isotope tracer approach in a eucalypt

    Science.gov (United States)

    Pendall, E.; Drake, J. E.; Furze, M.; Barton, C. V.; Carillo, Y.; Richter, A.; Tjoelker, M. G.

    2017-12-01

    Climate warming has the potential to alter the balance between photosynthetic carbon assimilation and respiratory losses in forest trees, leading to uncertainty in predicting their future physiological functioning. In a previous experiment, warming decreased canopy CO2 assimilation (A) rates of Eucalyptus tereticornis trees, but respiration (R) rates were usually not significantly affected, due to physiological acclimation to temperature. This led to a slight increase in (R/A) and thus decrease in plant carbon use efficiency with climate warming. In contrast to carbon fluxes, the effect of warming on carbon allocation and residence time in trees has received less attention. We conducted a study to test the hypothesis that warming would decrease the allocation of C belowground owing to reduced cost of nutrient uptake. E. parramattensis trees were grown in the field in unique whole-tree chambers operated at ambient and ambient +3 °C temperature treatments (n=3 per treatment). We applied a 13CO2 pulse and followed the label in CO2 respired from leaves, roots, canopy and soil, in plant sugars, and in rhizosphere microbes over a 3-week period in conjunction with measurements of tree growth. The 9-m tall, 57 m3 whole-tree chambers were monitored for CO2 concentrations in independent canopy and below ground (root and soil) compartments; periodic monitoring of δ13C values in air in the compartments allowed us to quantify the amount of 13CO2 assimilated and respired by each tree. Warmed trees grew faster and assimilated more of the label than control trees, but the 13C allocation to canopy, root and soil respiration was not altered. However, warming appeared to reduce the residence time of carbon respired from leaves, and especially from roots and soil, indicating that autotrophic respiration has the potential to feedback to climate change. This experiment provides insights into how warming may affect the fate of assimilated carbon from the leaf to the ecosystem scale.

  2. Estimation of residence times of coastal basins in the Laxemar- Simpevarp area between 3000 BC and 9000 AD

    Energy Technology Data Exchange (ETDEWEB)

    Engqvist, Anders (AandI Engqvist Konsult HB, Vaxholm (Sweden))

    2010-09-15

    The assignment has consisted of computation of the morpho- and bathymetry of the coastal area of Laxemar-Simpevarp for the time period 3000 BC through 9000 AD, in order to estimate the residence times as yearly means of volume-averaged specific age (Average Age, AvA) for water in coastal basins. These basins have been selected as belonging to earlier defined biosphere objects, containing anticipated exit points from possible radionuclides leaking from a hypothetical underground repository for spent nuclear fuel. This endeavor starts with partitioning of the coast into appropriate sub-basins interconnected by straits in an as objective manner as possible. This has been performed in cooperation with Umeaa Univ. followed by the transformation of these hypsographical data to a form that can serve as input data to the employed numerical CouBa-model. This model has been developed to simulate the water exchange of straits between densimetrically stably stratified basins with a free sea level including advection and mixing of water-borne conservative scalar properties, e.g. salinity, heat and specific age. The forcing of the model consists of run-off, wind-induced stress, thermal surface dynamics (heating/cooling) and density fluctuations at the open boundary toward the coastal zone, relative by which the specific water age is calculated For these ambient forcing factors there do not exist sufficiently precise climate data other than for contemporary times. For all other time periods the measured and/or model-computed forcing data regarding 2004 have been used. Estimated AvA-values for the different time periods are thus an expression of sub-basin configuration and hypsographical differences. An overriding directive has been to rather overestimate than underestimate the residence times, as to avoid underestimation of the subsequent dose calculations. The results of these AvA computations, presented as volume averages of yearly means of the sixteen biosphere object

  3. Fed and fasted gastric pH and gastric residence time in conscious beagle dogs.

    Science.gov (United States)

    Sagawa, Kazuko; Li, Fasheng; Liese, Ryan; Sutton, Steven C

    2009-07-01

    The gastric pH values are controversial in the literature. Some suggest the dog gastric pH is higher than human and dog gastric pH after fed with particular diet is uncertain. Gastric pH in 16 male beagle dogs was measured using Bravo pH telemetry system. For the fed study, the dogs received 10 or 200 g of dog dry food (5L18) 15 min before dosing the Bravo pH capsule, followed by a 50 mL of water to aid in swallowing. It was surprising to find a small, but statistically significantly lower pH in the fed compared to the fasted stomach. The average gastric pH in fasted dogs was 2.05 and 1.08 and 1.26 for 10 and 200 g fed dogs. The average gastric emptying time of the capsule was 1.4, 9.4 and 20 h for fasted, 10 g fed and 200 g fed dogs, respectively. The inter-individual variability was higher in fasted dogs than in fed dogs. The results showed the gastric pH in each colony of dogs can be different from reported values in the literature. It emphasizes that the importance of measuring the pH in each colony when dogs are used to evaluate pharmacokinetics of pH sensitive drugs or formulations.

  4. Dynamics of flow–soot interaction in wrinkled non-premixed ethylene–air flames

    KAUST Repository

    Arias, Paul G.

    2015-08-17

    A two-dimensional simulation of a non-premixed ethylene–air flame was conducted by employing a detailed gas-phase reaction mechanism considering polycyclic aromatic hydrocarbons, an aerosol-dynamics-based soot model using a method of moments with interpolative closure, and a grey gas and soot radiation model using the discrete transfer method. Interaction of the sooting flame with a prescribed decaying random velocity field was investigated, with a primary interest in the effects of velocity fluctuations on the flame structure and the associated soot formation process for a fuel-strip configuration and a composition with mature soot growth. The temporally evolving simulation revealed a multi-layered soot formation process within the flame, at a level of detail not properly described by previous studies based on simplified soot models utilizing acetylene or naphthalene precursors for initial soot inception. The overall effect of the flame topology on the soot formation was found to be consistent with previous experimental studies, while a unique behaviour of localised strong oxidation was also noted. The imposed velocity fluctuations led to an increase of the scalar dissipation rate in the sooting zone, causing a net suppression in the soot production rate. Considering the complex structure of the soot formation layer, the effects of the imposed fluctuations vary depending on the individual soot reactions. For the conditions under study, the soot oxidation reaction was identified as the most sensitive to the fluctuations and was mainly responsible for the local suppression of the net soot production. © 2015 Taylor & Francis

  5. Uncertainties in carbon residence time and NPP-driven carbon uptake in terrestrial ecosystems of the conterminous USA: a Bayesian approach

    Directory of Open Access Journals (Sweden)

    Xuhui Zhou

    2012-10-01

    Full Text Available Carbon (C residence time is one of the key factors that determine the capacity of ecosystem C storage. However, its uncertainties have not been well quantified, especially at regional scales. Assessing uncertainties of C residence time is thus crucial for an improved understanding of terrestrial C sequestration. In this study, the Bayesian inversion and Markov Chain Monte Carlo (MCMC technique were applied to a regional terrestrial ecosystem (TECO-R model to quantify C residence times and net primary productivity (NPP-driven ecosystem C uptake and assess their uncertainties in the conterminous USA. The uncertainty was represented by coefficient of variation (CV. The 13 spatially distributed data sets of C pools and fluxes have been used to constrain TECO-R model for each biome (totally eight biomes. Our results showed that estimated ecosystem C residence times ranged from 16.6±1.8 (cropland to 85.9±15.3 yr (evergreen needleleaf forest with an average of 56.8±8.8 yr in the conterminous USA. The ecosystem C residence times and their CV were spatially heterogeneous and varied with vegetation types and climate conditions. Large uncertainties appeared in the southern and eastern USA. Driven by NPP changes from 1982 to 1998, terrestrial ecosystems in the conterminous USA would absorb 0.20±0.06 Pg C yr−1. Their spatial pattern was closely related to the greenness map in the summer with larger uptake in central and southeast regions. The lack of data or timescale mismatching between the available data and the estimated parameters lead to uncertainties in the estimated C residence times, which together with initial NPP resulted in the uncertainties in the estimated NPP-driven C uptake. The Bayesian approach with MCMC inversion provides an effective tool to estimate spatially distributed C residence time and assess their uncertainties in the conterminous USA.

  6. Family involvement in timely detection of changes in health of nursing homes residents: A qualitative exploratory study.

    Science.gov (United States)

    Powell, Catherine; Blighe, Alan; Froggatt, Katherine; McCormack, Brendan; Woodward-Carlton, Barbara; Young, John; Robinson, Louise; Downs, Murna

    2018-01-01

    To explore family perspectives on their involvement in the timely detection of changes in their relatives' health in UK nursing homes. Increasingly, policy attention is being paid to the need to reduce hospitalisations for conditions that, if detected and treated in time, could be managed in the community. We know that family continue to be involved in the care of their family members once they have moved into a nursing home. Little is known, however, about family involvement in the timely detection of changes in health in nursing home residents. Qualitative exploratory study with thematic analysis. A purposive sampling strategy was applied. Fourteen semi-structured one-to-one interviews with family members of people living in 13 different UK nursing homes. Data were collected from November 2015-March 2016. Families were involved in the timely detection of changes in health in three key ways: noticing signs of changes in health, informing care staff about what they noticed and educating care staff about their family members' changes in health. Families suggested they could be supported to detect timely changes in health by developing effective working practices with care staff. Families can provide a special contribution to the process of timely detection in nursing homes. Their involvement needs to be negotiated, better supported, as well as given more legitimacy and structure within the nursing home. Families could provide much needed support to nursing home nurses, care assistants and managers in timely detection of changes in health. This may be achieved through communication about their preferred involvement on a case-by-case basis as well as providing appropriate support or services. © 2017 The Authors. Journal of Clinical Nursing Published by John Wiley & Sons Ltd.

  7. Morphological effects on the radiative properties of soot aerosols in different internally mixing states with sulfate

    Science.gov (United States)

    Dong, J.; Zhao, J. M.; Liu, L. H.

    2015-11-01

    The radiative properties of soot aerosols largely depend on their mixing state and morphology factors. In this paper, we generated soot aggregates in four mixing states with sulfate, including bare soot, partly coated soot, heavily coated soot and soot with inclusion. The number of monomers and fractal dimension of soot were varied in each mixing state while the radius of monomers was fixed at 0.025 μm. Using the discrete dipole approximation method (DDA), we calculated optical parameters relevant for climate forcing simulation at mid-visible wavelength (0.55 μm). Internal mixing results in enhanced absorption, scattering cross sections as well as the single scattering albedo. The enhancement ratio of the absorption is largest for heavily coated soot, which ranges from 1.5 to 1.65 with a soot volume fraction of 0.15 and is larger for soot with larger fractal dimension. The scattering cross section can be dramatically increased by factors larger than 10 when soot is heavily coated. The increasing of both the scattering cross section and the single scattering albedo is larger for soot aggregates with smaller number of monomers and fractal dimension. The asymmetry parameter is insensitive to the fractal dimension for heavily coated soot and soot with inclusion. Two simplified models including the homogeneous sphere model (HS) and the core shell sphere model (CS) were examined using the DDA results as references. The performance of the HS and CS model largely depends on the morphology factors and the mixing state of soot. For bare and partly coated soot, both the HS and CS model can introduce relative errors as large as several tens percent. For heavily coated soot, the HS model predicts the absorption with relative errors within 10%, while it overestimates the absorption with relative errors no larger than 20% for soot with inclusion. The HS model predicts the single scattering albedo and the asymmetry parameter with relative errors no larger than 10% for heavily

  8. Online determination of polycyclic aromatic hydrocarbon formation from a flame soot generator.

    Science.gov (United States)

    Mueller, Laarnie; Jakobi, Gert; Orasche, Juergen; Karg, Erwin; Sklorz, Martin; Abbaszade, Gülcin; Weggler, Benedict; Jing, Lianpeng; Schnelle-Kreis, Juergen; Zimmermann, Ralf

    2015-08-01

    In this study, we produced a class of diffusion flame soot particles with varying chemical and physical properties by using the mini-Combustion Aerosol STandard (CAST) and applying varying oxidant gas flow rates under constant propane, quenching, and dilution gas supply. We varied the soot properties by using the following fuel-to-air equivalence ratios (Φ): 1.13, 1.09, 1.04, 1.00, 0.96, and 0.89. Within this Φ range, we observed drastic changes in the physical and chemical properties of the soot. Oxidant-rich flames (Φ  1). To investigate the polycyclic aromatic hydrocarbons (PAH) formation online, we developed a new method for quantification by using the one (13)C-containing doubly charged PAH ion in a high-resolution time-of-flight aerosol mass spectrometry (HR-ToF-AMS). The time-resolved concentration showed that the larger PAHs prevailed in the fuel-rich flames and diminished in the oxidant-rich flames. By comparison with the offline in situ derivatization-thermal-desorption gas-chromatography time-of-flight mass spectrometry (IDTD-GC-ToF-MS), we found that the concentration by using the HR-ToF-AMS was underestimated, especially for lower mass PAHs (C14-C18) in the fuel-rich flames possibly due to size limitation and degradation of semi-volatile species under high vacuum and desorption temperature in the latter. For oxidant-rich flames, the large PAHs (C20 and C22) were detected in the HR-ToF-AMS while it was not possible in IDTD-GC-ToF-MS due to matrix effect. The PAH formation was discussed based on the combination of our results and with respect to Φ settings.

  9. Improving Timely Resident Follow-Up and Communication of Results in Ambulatory Clinics Utilizing a Web-Based Audit and Feedback Module.

    Science.gov (United States)

    Boggan, Joel C; Swaminathan, Aparna; Thomas, Samantha; Simel, David L; Zaas, Aimee K; Bae, Jonathan G

    2017-04-01

    Failure to follow up and communicate test results to patients in outpatient settings may lead to diagnostic and therapeutic delays. Residents are less likely than attending physicians to report results to patients, and may face additional barriers to reporting, given competing clinical responsibilities. This study aimed to improve the rates of communicating test results to patients in resident ambulatory clinics. We performed an internal medicine, residency-wide, pre- and postintervention, quality improvement project using audit and feedback. Residents performed audits of ambulatory patients requiring laboratory or radiologic testing by means of a shared online interface. The intervention consisted of an educational module viewed with initial audits, development of a personalized improvement plan after Phase 1, and repeated real-time feedback of individual relative performance compared at clinic and program levels. Outcomes included results communicated within 14 days and prespecified "significant" results communicated within 72 hours. A total of 76 of 86 eligible residents (88%) reviewed 1713 individual ambulatory patients' charts in Phase 1, and 73 residents (85%) reviewed 1509 charts in Phase 2. Follow-up rates were higher in Phase 2 than Phase 1 for communicating results within 14 days and significant results within 72 hours (85% versus 78%, P  audit and feedback quality improvement project can improve rates of resident follow-up and communication of results, although communication gaps remained.

  10. Nanoparticle production by UV irradiation of combustion generated soot particles

    International Nuclear Information System (INIS)

    Stipe, Christopher B.; Choi, Jong Hyun; Lucas, Donald; Koshland, Catherine P.; Sawyer, Robert F.

    2004-01-01

    Laser ablation of surfaces normally produce high temperature plasmas that are difficult to control. By irradiating small particles in the gas phase, we can better control the size and concentration of the resulting particles when different materials are photofragmented. Here, we irradiate soot with 193 nm light from an ArF excimer laser. Irradiating the original agglomerated particles at fluences ranging from 0.07 to 0.26 J/cm 2 with repetition rates of 20 and 100 Hz produces a large number of small, unagglomerated particles, and a smaller number of spherical agglomerated particles. Mean particle diameters from 20 to 50 nm are produced from soot originally having a mean electric mobility diameter of 265nm. We use a non-dimensional parameter, called the photon/atom ratio (PAR), to aid in understanding the photofragmentation process. This parameter is the ratio of the number of photons striking the soot particles to the number of the carbon atoms contained in the soot particles, and is a better metric than the laser fluence for analyzing laser-particle interactions. These results suggest that UV photofragmentation can be effective in controlling particle size and morphology, and can be a useful diagnostic for studying elements of the laser ablation process

  11. Effect of cheese on intestinal transit time and other indicators of bowel function in residents of a retirement home.

    Science.gov (United States)

    Mykkänen, H M; Karhunen, L J; Korpela, R; Salminen, S

    1994-01-01

    Effects of increased intake of cheese on intestinal transit time and other indicators of bowel function were studied in 21 retirement home residents (18 women and 3 men; age, 68-87 years). The study was divided into four succeeding periods: 1) 1-week basal period (usual diet); 2)3-week cheese period (extra cheese was offered as such on bread or used in cooking); 3) 3-week no-cheese period (all cheese on bread was replaced with cured meats and cold cuts, and no cheese was used in cooking); 4) 3-week follow-up period (usual diet). During the last week of each period a questionnaire was filled out on fecal frequencies, consistency of feces (soft, normal, hard), and occurrence of abdominal pain and flatulence. Use of laxative medications and therapeutic foods (prunes) was registered. Eleven of the 21 subjects collected fecal samples for the determination of fecal wet weight and intestinal transit time by means of radiopaque Sitzmark capsules. Intakes of cheese, fiber-containing foods, and fluids by these 11 subjects during meals offered in the cafeteria were recorded on a prefilled questionnaire. In spite of a 10-fold increase in the intake of cheese no change in intestinal transit time, fecal frequency, fecal wet weight, consistency of feces, and occurrence of gastrointestinal symptoms was observed. The use of laxative medication was higher during the cheese period, but no change in the combined use of laxative medication and therapeutic foods (prunes) was observed.(ABSTRACT TRUNCATED AT 250 WORDS)

  12. Gasification of biomass wastes in an entrained flow gasifier: Effect of the particle size and the residence time

    Energy Technology Data Exchange (ETDEWEB)

    Hernandez, Juan J.; Aranda-Almansa, Guadalupe [Universidad de Castilla-La Mancha, Departamento de Mecanica Aplicada e Ingenieria de Proyectos, Escuela Tecnica Superior de Ingenieros Industriales (Edificio Politecnico), Avenida Camilo Jose Cela s/n, 13071 Ciudad Real (Spain); Bula, Antonio [Universidad del Norte, Departamento de Ingenieria Mecanica, Km.5 Antigua Via Puerto Colombia, Barranquilla (Colombia)

    2010-06-15

    Experimental tests in an entrained flow gasifier have been carried out in order to evaluate the effect of the biomass particle size and the space residence time on the gasifier performance and the producer gas quality. Three types of biomass fuels (grapevine pruning and sawdust wastes, and marc of grape) and a fossil fuel (a coal-coke blend) have been tested. The results obtained show that a reduction in the fuel particle size leads to a significant improvement in the gasification parameters. The thermochemical characterisation of the resulting char-ash residue shows a sharp increase in the fuel conversion for particles below 1 mm diameter, which could be adequate to be used in conventional entrained flow gasifiers. Significant differences in the thermochemical behaviour of the biomass fuels and the coal-coke blend have been found, especially in the evolution of the H{sub 2}/CO ratio with the space time, mainly due to the catalytic effect of the coal-coke ash. The reaction temperature and the space time have a significant effect on the H{sub 2}/CO ratio (the relative importance of each of these parameters depending on the temperature), this value being independent of the fuel particle size. (author)

  13. Fragmentation and bond strength of airborne diesel soot agglomerates

    Directory of Open Access Journals (Sweden)

    Messerer Armin

    2008-06-01

    Full Text Available Abstract Background The potential of diesel soot aerosol particles to break up into smaller units under mechanical stress was investigated by a direct impaction technique which measures the degree of fragmentation of individual agglomerates vs. impact energy. Diesel aerosol was generated by an idling diesel engine used for passenger vehicles. Both the aerosol emitted directly and aerosol that had undergone additional growth by Brownian coagulation ("aging" was investigated. Optionally a thermo-desoption technique at 280°C was used to remove all high-volatility and the majority of low-volatility HC adsorbates from the aerosol before aging. Results It was found that the primary soot agglomerates emitted directly from the engine could not be fragmented at all. Soot agglomerates permitted to grow additionally by Brownian coagulation of the primary emitted particles could be fragmented to a maximum of 75% and 60% respectively, depending on whether adsorbates were removed from their surface prior to aging or not. At most, these aged agglomerates could be broken down to roughly the size of the agglomerates from the primary emission. The energy required for a 50% fragmentation probability of all bonds within an agglomerate was reduced by roughly a factor of 2 when aging "dry" agglomerates. Average bond energies derived from the data were 0.52*10-16 and 1.2*10-16 J, respectively. This is about 2 orders of magnitude higher than estimates for pure van-der-Waals agglomerates, but agrees quite well with other observations. Conclusion Although direct conclusions regarding the behavior of inhaled diesel aerosol in contact with body fluids cannot be drawn from such measurements, the results imply that highly agglomerated soot aerosol particles are unlikely to break up into units smaller than roughly the size distribution emitted as tail pipe soot.

  14. Fragmentation and bond strength of airborne diesel soot agglomerates

    Science.gov (United States)

    Rothenbacher, Sonja; Messerer, Armin; Kasper, Gerhard

    2008-01-01

    Background The potential of diesel soot aerosol particles to break up into smaller units under mechanical stress was investigated by a direct impaction technique which measures the degree of fragmentation of individual agglomerates vs. impact energy. Diesel aerosol was generated by an idling diesel engine used for passenger vehicles. Both the aerosol emitted directly and aerosol that had undergone additional growth by Brownian coagulation ("aging") was investigated. Optionally a thermo-desoption technique at 280°C was used to remove all high-volatility and the majority of low-volatility HC adsorbates from the aerosol before aging. Results It was found that the primary soot agglomerates emitted directly from the engine could not be fragmented at all. Soot agglomerates permitted to grow additionally by Brownian coagulation of the primary emitted particles could be fragmented to a maximum of 75% and 60% respectively, depending on whether adsorbates were removed from their surface prior to aging or not. At most, these aged agglomerates could be broken down to roughly the size of the agglomerates from the primary emission. The energy required for a 50% fragmentation probability of all bonds within an agglomerate was reduced by roughly a factor of 2 when aging "dry" agglomerates. Average bond energies derived from the data were 0.52*10-16 and 1.2*10-16 J, respectively. This is about 2 orders of magnitude higher than estimates for pure van-der-Waals agglomerates, but agrees quite well with other observations. Conclusion Although direct conclusions regarding the behavior of inhaled diesel aerosol in contact with body fluids cannot be drawn from such measurements, the results imply that highly agglomerated soot aerosol particles are unlikely to break up into units smaller than roughly the size distribution emitted as tail pipe soot. PMID:18533015

  15. Modelling thermal radiation and soot formation in buoyant diffusion flames

    International Nuclear Information System (INIS)

    Demarco Bull, R.A.

    2012-01-01

    The radiative heat transfer plays an important role in fire problems since it is the dominant mode of heat transfer between flames and surroundings. It controls the pyrolysis, and therefore the heat release rate, and the growth rate of the fire. In the present work a numerical study of buoyant diffusion flames is carried out, with the main objective of modelling the thermal radiative transfer and the soot formation/destruction processes. In a first step, different radiative property models were tested in benchmark configurations. It was found that the FSCK coupled with the Modest and Riazzi mixing scheme was the best compromise in terms of accuracy and computational requirements, and was a good candidate to be implemented in CFD codes dealing with fire problems. In a second step, a semi-empirical soot model, considering acetylene and benzene as precursor species for soot nucleation, was validated in laminar co flow diffusion flames over a wide range of hydrocarbons (C1-C3) and conditions. In addition, the optically-thin approximation was found to produce large discrepancies in the upper part of these small laminar flames. Reliable predictions of soot volume fractions require the use of an advanced radiation model. Then the FSCK and the semi-empirical soot model were applied to simulate laboratory-scale and intermediate-scale pool fires of methane and propane. Predicted flame structures as well as the radiant heat flux transferred to the surroundings were found to be in good agreement with the available experimental data. Finally, the interaction between radiation and turbulence was quantified. (author)

  16. Residence and transport time scales associated with Shatt Al-Arab discharges under various hydrological conditions estimated using a numerical model.

    Science.gov (United States)

    Alosairi, Yousef; Pokavanich, Tanuspong

    2017-05-15

    Over the last several decades, concerns in the Northwest Arabian Gulf have risen regarding water quality and ecological conditions, particularly near Kuwait. This interest is mainly attributed to the reduction of freshwater discharge and its associated constituents from the Shatt Al Arab as a result of human activities at diverse scales. From the hydrological perspective, the reduction has also resulted in alteration to the dynamic regime and related residence time and transport conditions. Using a previously well-validated three-dimensional numerical model of the Northern Arabian Gulf (NAG) (Alosairi and Pokavanich, 2017), the residence and transport conditions of numerical tracers have been assessed through a series of numerical tests. The results indicate that density-driven circulations have played a key role in reducing the residence time in the Northwest Gulf by approximately 15% to 20% compared to tidal forces only. The transport conditions correlated well with the Shatt Al Arab discharges, but they were only significant along the Kuwait coast due to counter-clockwise circulations and alongshore currents. Arrival times and mixing processes varied reasonably with the Shatt Al Arab discharges; the results exhibited the enhancement in mixing and transport with increases in discharge. Residence times in the NAG associated with Shatt Al Arab discharge displayed spatial variations, particularly in Kuwait Bay, where the residence time increased by 60days during low discharge compared to high discharge. Copyright © 2017 Elsevier Ltd. All rights reserved.

  17. An estimation of the average residence times and onshore-offshore diffusivities of beached microplastics based on the population decay of tagged meso- and macrolitter.

    Science.gov (United States)

    Hinata, Hirofumi; Mori, Keita; Ohno, Kazuki; Miyao, Yasuyuki; Kataoka, Tomoya

    2017-09-15

    Residence times of microplastics were estimated based on the dependence of meso- and macrolitter residence times on their upward terminal velocities (UTVs) in the ocean obtained by one- and two-year mark-recapture experiments conducted on Wadahama Beach, Nii-jima Island, Japan. A significant linear relationship between the residence time and UTV was found in the velocity range of about 0.3-0.9ms -1 , while there was no significant difference between the residence times obtained in the velocity range of about 0.9-1.4ms -1 . This dependence on the UTV would reflect the uprush-backwash response of the target items to swash waves on the beach. By extrapolating the linear relationship down to the velocity range of microplastics, the residence times of microplastics and the 1D onshore-offshore diffusion coefficients were inferred, and are one to two orders of magnitude greater than the coefficients of the macroplastics. Copyright © 2017 Elsevier Ltd. All rights reserved.

  18. Quantifying the residence time and flushing characteristics of a shallow, back-barrier estuary: Application of hydrodynamic and particle tracking models

    Science.gov (United States)

    Defne, Zafer; Ganju, Neil K.

    2015-01-01

    Estuarine residence time is a major driver of eutrophication and water quality. Barnegat Bay-Little Egg Harbor (BB-LEH), New Jersey, is a lagoonal back-barrier estuary that is subject to anthropogenic pressures including nutrient loading, eutrophication, and subsequent declines in water quality. A combination of hydrodynamic and particle tracking modeling was used to identify the mechanisms controlling flushing, residence time, and spatial variability of particle retention. The models demonstrated a pronounced northward subtidal flow from Little Egg Inlet in the south to Pt. Pleasant Canal in the north due to frictional effects in the inlets, leading to better flushing of the southern half of the estuary and particle retention in the northern estuary. Mean residence time for BB-LEH was 13 days but spatial variability was between ∼0 and 30 days depending on the initial particle location. Mean residence time with tidal forcing alone was 24 days (spatial variability between ∼0 and 50 days); the tides were relatively inefficient in flushing the northern end of the Bay. Scenarios with successive exclusion of physical processes from the models revealed that meteorological and remote offshore forcing were stronger drivers of exchange than riverine inflow. Investigations of water quality and eutrophication should take into account spatial variability in hydrodynamics and residence time in order to better quantify the roles of nutrient loading, production, and flushing.

  19. Optimized Heating Rate and Soot-catalyst Ratio for Soot Oxidation over MoO3 Catalyst

    Directory of Open Access Journals (Sweden)

    Congwei Mei

    2017-10-01

    Full Text Available MoO3 is now utilized as a promising catalyst due to its high activity and favorable mobility at low temperature. Its spectral data and surface microstructures were characterized by Fourier transform infrared spectra (FT-IR and Field emission scanning electron microscope (FESEM. Thermo-analysis of the carbon black was performed over nano-MoO3 catalyst in a thermogravimetric analyzer (TGA at various heating rates and soot-catalyst ratios. Through the analysis of kinetic parameters, we found that the heat transfer effect and diffusion effect can be removed by setting lower heating rates and soot-catalyst ratios. Therefore, a strategy for selecting proper thermogravimetric parameters were established, which can contribute to the better understanding of thermo-analytical process. Copyright © 2017 BCREC Group. All rights reserved Received: 4th December 2016; Revised: 13rd June 2017; Accepted: 9th April 2017; Available online: 27th October 2017; Published regularly: December 2017 How to Cite: Mei, C., Mei, D., Yue, S, Chen, Z., Yuan, Y. (2017. Optimized Heating Rate and Soot-catalyst Ratio for Soot Oxidation over MoO3 Catalyst. Bulletin of Chemical Reaction Engineering & Catalysis, 12 (3: 408-414 (doi:10.9767/bcrec.12.3.845.408-414

  20. Budget and residence time of {sup 210}Pb along the Gulf of Lion`s continental slope (Northwestern Mediterranean Sea)

    Energy Technology Data Exchange (ETDEWEB)

    Abassi, A.; Radakovitch, O.; Heussner, S.; Monaco, A. [Perpignan Univ., 66 (France). Lab. de Sedimentologie et Geochimie Marines

    1997-12-31

    Concentration of {sup 210}Pb has been measured in water and sediment trap samples collected on 7 experimental sites representative of the Gulf of Lion`s continental margin. This marine system is characterised by a major continental input through the Rhone river and a powerful along-slope cyclonic current (Northern Current). From the distribution of bulk {sup 210}Pb activities, it was intended to gain some information on the processes controlling the transport of trace metals at the ocean/continent boundary. Residence times of {sup 210}Pb relative to scavenging in surface waters (0-100 m) showed a constant along-slope (i.e., downstream) decrease that can be related to increasing concentrations in suspended particles. Annual time-series of {sup 210}Pb activities in settling particles were determined on samples collected by traps at 500 and 1000 m depth. From this data set, a budget for {sup 210}Pb on this margin was established which permitted to determine the flux of {sup 210}Pb theoretically adsorbed onto particles. This theoretical flux was compared, at each site, with fluxes effectively measured by traps and revealed that exchange processes - mainly in the form of large inputs of this nuclide (import of 47 to 93% of measured flux) - largely affect the {sup 210}Pb distribution on this continental margin. (author) 12 refs.

  1. Budget and residence time of 210Pb along the Gulf of Lion's continental slope (Northwestern Mediterranean Sea)

    International Nuclear Information System (INIS)

    Abassi, A.; Radakovitch, O.; Heussner, S.; Monaco, A.

    1997-01-01

    Concentration of 210 Pb has been measured in water and sediment trap samples collected on 7 experimental sites representative of the Gulf of Lion's continental margin. This marine system is characterised by a major continental input through the Rhone river and a powerful along-slope cyclonic current (Northern Current). From the distribution of bulk 210 Pb activities, it was intended to gain some information on the processes controlling the transport of trace metals at the ocean/continent boundary. Residence times of 210 Pb relative to scavenging in surface waters (0-100 m) showed a constant along-slope (i.e., downstream) decrease that can be related to increasing concentrations in suspended particles. Annual time-series of 210 Pb activities in settling particles were determined on samples collected by traps at 500 and 1000 m depth. From this data set, a budget for 210 Pb on this margin was established which permitted to determine the flux of 210 Pb theoretically adsorbed onto particles. This theoretical flux was compared, at each site, with fluxes effectively measured by traps and revealed that exchange processes - mainly in the form of large inputs of this nuclide (import of 47 to 93% of measured flux) - largely affect the 210 Pb distribution on this continental margin. (author)

  2. The role of exposure time in computerized training of prostate cryosurgery: performance comparison of surgical residents with engineering students.

    Science.gov (United States)

    Joshi, Purva; Sehrawat, Anjali; Rabin, Yoed

    2018-04-01

    This study aims at the evaluation of a prototype of a computerized trainer for cryosurgery-the controlled destruction of cancer tumors by freezing. The hypothesis in this study is that computer-based cryosurgery training for an optimal cryoprobe layout is essentially a matter of exposure time, rather than trainee background or the specific computer-generated planning target. Key geometric features under considerations are associated with spatial limitations on cryoprobes placement and the match between the resulted thermal field and the unique anatomy of the prostate. All experiments in this study were performed on the cryosurgery trainer-a prototype platform for computerized cryosurgery training, which has been presented previously. Among its key features, the cryosurgery trainer displays the prostate shape and its contours and provides a distance measurement tool on demand, in order to address spatial constraints during ultrasound imaging guidance. Another unique feature of the cryosurgery trainer is an output movie, displaying the simulated thermal field at the end of the cryoprocedure. The current study was performed on graduate engineering students having no formal background in medicine, and the results were benchmarked against data obtained on surgical residents having no experience with cryosurgery. Despite fundamental differences in background and experience, neither group displayed superior performance when it comes to cryoprobe layout planning. This study demonstrates that computer-based training of an optimal cryoprobe layout is feasible. This study demonstrates that the training quality is essentially related to the training exposure time, rather than to a specific planning strategy from those investigated.

  3. Soot modeling of counterflow diffusion flames of ethylene-based binary mixture fuels

    KAUST Repository

    Wang, Yu

    2015-03-01

    A soot model was developed based on the recently proposed PAH growth mechanism for C1-C4 gaseous fuels (KAUST PAH Mechanism 2, KM2) that included molecular growth up to coronene (A7) to simulate soot formation in counterflow diffusion flames of ethylene and its binary mixtures with methane, ethane and propane based on the method of moments. The soot model has 36 soot nucleation reactions from 8 PAH molecules including pyrene and larger PAHs. Soot surface growth reactions were based on a modified hydrogen-abstraction-acetylene-addition (HACA) mechanism in which CH3, C3H3 and C2H radicals were included in the hydrogen abstraction reactions in addition to H atoms. PAH condensation on soot particles was also considered. The experimentally measured profiles of soot volume fraction, number density, and particle size were well captured by the model for the baseline case of ethylene along with the cases involving mixtures of fuels. The simulation results, which were in qualitative agreement with the experimental data in the effects of binary fuel mixing on the sooting structures of the measured flames, showed in particular that 5% addition of propane (ethane) led to an increase in the soot volume fraction of the ethylene flame by 32% (6%), despite the fact that propane and ethane are less sooting fuels than is ethylene, which is in reasonable agreement with experiments of 37% (14%). The model revealed that with 5% addition of methane, there was an increase of 6% in the soot volume fraction. The average soot particle sizes were only minimally influenced while the soot number densities were increased by the fuel mixing. Further analysis of the numerical data indicated that the chemical cross-linking effect between ethylene and the dopant fuels resulted in an increase in PAH formation, which led to higher soot nucleation rates and therefore higher soot number densities. On the other hand, the rates of soot surface growth per unit surface area through the HACA mechanism were

  4. A Phenomenological Model for Prediction Auto-Ignition and Soot Formation of Turbulent Diffusion Combustion in a High Pressure Common Rail Diesel Engine

    Directory of Open Access Journals (Sweden)

    Qinghui Zhou

    2011-06-01

    Full Text Available A new phenomenological model, the TP (Temperature Phase model, is presented to carry out optimization calculations for turbulent diffusion combustion in a high-pressure common rail diesel engine. Temperature is the most important parameter in the TP model, which includes two parts: an auto-ignition and a soot model. In the auto-ignition phase, different reaction mechanisms are built for different zones. For the soot model, different methods are used for different temperatures. The TP model is then implemented in KIVA code instead of original model to carry out optimization. The results of cylinder pressures, the corresponding heat release rates, and soot with variation of injection time, variation of rail pressure and variation of speed among TP model, KIVA standard model and experimental data are analyzed. The results indicate that the TP model can carry out optimization and CFD (computational fluid dynamics and can be a useful tool to study turbulent diffusion combustion.

  5. Groundwater residence time and aquifer recharge in mutilayered, semi-confined and faulted aquifer systems using environmental tracers

    Science.gov (United States)

    Batlle-Aguilar, J.; Banks, E.; Batelaan, O.; Kipfer, R.; Brennwald, M. S.; Cook, P. G.

    2016-12-01

    Population growth and ongoing climate change threatens the future of water supply in many regions. Therefore water resources need to be managed in a way such that water demands for industrial, agricultural, recreation and household uses are met in a sustainable approach. To do so, appropriate knowledge of groundwater residence time and aquifer recharge is paramount. But populations are largely concentrated on sedimentary basins where aquifers are often multi-layered, semi-confined and faulted, challenging the study of groundwater flow processes. The motivation of this work is to study the potential of environmental tracers (δ18O, δ2H, δ13C, 14C, 4He, 20Ne, 40Ar, N2) to assist our understanding of recharge processes and residence times in semi-confined, multilayered and faulted aquifer systems. For that purpose, the coastal aquifer system in the Adelaide Plains basin, South Australia, was studied. Carbon-14 groundwater ages were found to increase with depth and distance (30,000 years near the coast), confirming the system is semi-confined and the palaeometeoric origin of groundwater, as suggested by water stable isotopes. The presence of old groundwater near the top of deep semi-confined aquifers suggested that recharge mainly occurs in the mountain ranges east of the basin, a finding which was supported by higher Cl concentrations in the overlying Quaternary aquifers. Mean groundwater flow velocity of 0.8 m y-1 was estimated using 14C ages, and confirmed with 4He estimations. However 4He accumulation rates ranging between 8×10-12 and 1×10-10 cm3 STP g-1 y-1 and 1.7-7.1×10-7 cm3 STP g-1 km-1 confirmed slower flow velocities in some areas, velocities that could not be captured using 14C. Faults were found to play a paramount role in mixing old fluids rich in salts and 4He, but it was not possible to demonstrate the role of faults in changing flow velocities, which requires a higher density of sampling points. Our study shows that environmental tracers are a

  6. Rational optimization of drug-target residence time: Insights from inhibitor binding to the S. aureus FabI enzyme-product complex

    Science.gov (United States)

    Chang, Andrew; Schiebel, Johannes; Yu, Weixuan; Bommineni, Gopal R.; Pan, Pan; Baxter, Michael V.; Khanna, Avinash; Sotriffer, Christoph A.; Kisker, Caroline; Tonge, Peter J.

    2013-01-01

    Drug-target kinetics has recently emerged as an especially important facet of the drug discovery process. In particular, prolonged drug-target residence times may confer enhanced efficacy and selectivity in the open in vivo system. However, the lack of accurate kinetic and structural data for series of congeneric compounds hinders the rational design of inhibitors with decreased off-rates. Therefore, we chose the Staphylococcus aureus enoyl-ACP reductase (saFabI) - an important target for the development of new anti-staphylococcal drugs - as a model system to rationalize and optimize the drug-target residence time on a structural basis. Using our new, efficient and widely applicable mechanistically informed kinetic approach, we obtained a full characterization of saFabI inhibition by a series of 20 diphenyl ethers complemented by a collection of 9 saFabI-inhibitor crystal structures. We identified a strong correlation between the affinities of the investigated saFabI diphenyl ether inhibitors and their corresponding residence times, which can be rationalized on a structural basis. Due to its favorable interactions with the enzyme, the residence time of our most potent compound exceeds 10 hours. In addition, we found that affinity and residence time in this system can be significantly enhanced by modifications predictable by a careful consideration of catalysis. Our study provides a blueprint for investigating and prolonging drug-target kinetics and may aid in the rational design of long-residence-time inhibitors targeting the essential saFabI enzyme. PMID:23697754

  7. Residency training program: Perceptions of residents

    African Journals Online (AJOL)

    This study was carried out to ascertain the perception of the residency ... the time of the study. Analysis of the respondents showed similar findings for both senior and junior levels of training. Discussion. The introduction of the residency training program .... Overseas training/ attachment should be re-introduced. 12. (10.1).

  8. An experimental study on the effects of different opening ranges of waste-gate on the exhaust soot emission of a turbo-charged DI diesel engine

    International Nuclear Information System (INIS)

    Ghazikhani, M.; Davarpanah, M.; Shaegh, S.A. Mousavi

    2008-01-01

    This experimental study was conducted to investigate the effects of different opening ranges of waste-gate of a turbo-charged DI diesel engine on improving the exhaust soot emission. Different opening ranges of waste-gate were supplied using an adjustable spring to load the actuating rod of the waste-gate in which, increasing the opening range of the waste-gate decreases the inlet manifold pressure. In this study, the maximum inlet manifold pressures which were supplied by changing the opening range of waste-gate were 0.1 bar, 0.23 bar, 0.26 bar and 0.52 bar over atmosphere and experiments were conducted under the ECE-R49, 13 mode standard test. At each mode of the test, soot emission was recorded and then brake specific soot emission was calculated. Results indicate that, soot emission decreases with increasing the maximum inlet manifold pressure from 0.1 bar to 0.23 bar. This reduction may be due to increasing the intake-air temperature which results in reduction of ignition delay that prolongs the late combustion phase. This improves the soot burnout process because enough time and sufficient in-cylinder temperature are available at the late combustion phase prior to exhaust valve opening. While for the higher maximum inlet manifold pressures from 0.23 bar to 0.52 bar, although there are enough time at the late combustion phase, but the soot emission increases which could be due to more reduction of the in-cylinder gas temperature at the end of combustion before EVO

  9. Effects of first-pass metabolism on metabolite mean residence time determination after oral administration of parent drug.

    Science.gov (United States)

    Chan, K K; Gibaldi, M

    1990-01-01

    Metabolite kinetics after oral drug administration can be determined, without separate metabolite administration, using the concepts of mean residence time (MRT). The MRT of parent drug and metabolite after oral administration of the parent drug, MRTp,p(oral) and MRTm,p(oral), can be calculated directly from the drug and metabolite profiles. The difference between MRTm,p(oral) and MRTp,p(oral), termed Delta MRT, yields an estimate of MRT of metabolite when the metabolite is given as an iv bolus, MRTm,m(iv). The calculation is simple for drugs that are known to undergo, negligible first-pass metabolism. Correction can also be made when extent of first-pass metabolism is known. Ambiguity is encountered, however, when the degree of first-pass metabolism is unknown. When the delta MRT is negative, then first-pass metabolism must be considered. A positive value of delta MRT, on the other hand, is not a definitive indication of the absence of first-pass metabolism. It may occur in the presence or absence of first-pass metabolism. Ignoring the possibility of first-pass metabolism when a positive value of delta MRT occurs may lead to an incorrect estimate of MRTm,m(iv). The estimation error is relatively small, however, when MRTm,m(iv) much greater than MRTp,p(iv), even when first-pass metabolism is extensive. This situation may apply to the administration of a prodrug.

  10. Denitrification in a low-temperature bioreactor system at two different hydraulic residence times: laboratory column studies.

    Science.gov (United States)

    Nordström, Albin; Herbert, Roger B

    2017-06-01

    Nitrate removal rates in a mixture of pine woodchips and sewage sludge were determined in laboratory column studies at 5°C, 12°C, and 22°C, and at two different hydraulic residence times (HRTs; 58.2-64.0 hours and 18.7-20.6 hours). Baffles installed in the flow path were tested as a measure to reduce preferential flow behavior, and to increase the nitrate removal in the columns. The nitrate removal in the columns was simulated at 5°C and 12°C using a combined Arrhenius-Monod equation controlling the removal rate, and a first-order exchange model for incorporation of stagnant zones. Denitrification in the mixture of pine woodchips and sewage sludge reduced nitrate concentrations of 30 mg N L -1 at 5°C to below detection limits at a HRT of 58.2-64.0 hours. At a HRT of 18.7-20.6 hours, nitrate removal was incomplete. The Arrhenius frequency factor and activation energy retrieved from the low HRT data supported a biochemically controlled reaction rate; the same parameters, however, could not be used to simulate the nitrate removal at high HRT. The results show an inversely proportional relationship between the advection velocity and the nitrate removal rate, suggesting that bioreactor performance could be enhanced by promoting low advection velocities.

  11. Charge and energy dependence of the residence time of cosmic ray nuclei below 15 GeV/nucleon

    International Nuclear Information System (INIS)

    Soutoul, A.; Engelmann, J.J.; Ferrando, P.; Koch-Miramond, L.; Masse, P.; Webber, W.R.

    1985-01-01

    The relative abundance of nuclear species measured in cosmic rays at Earth has often been interpreted with the simple leaky box model. For this model to be consistent an essential requirement is that the escape length does not depend on the nuclear species. The discrepancy between escape length values derived from iron secondaries and from the B/C ratio was identified by Garcia-Munoz and his co-workers using a large amount of experimental data. Ormes and Protheroe found a similar trend in the HEAO data although they questioned its significance against uncertainties. They also showed that the change in the B/C ratio values implies a decrease of the residence time of cosmic rays at low energies in conflict with the diffusive convective picture. These conclusions crucially depend on the partial cross section values and their uncertainties. Recently new accurate cross sections of key importance for propagation calculations have been measured. Their statistical uncertainties are often better than 4% and their values significantly different from those previously accepted. Here, these new cross sections are used to compare the observed B/C+O and (Sc to Cr)/Fe ratio to those predicted with the simple leaky box model

  12. Rapid generation of volatile fatty acids (VFA) through anaerobic acidification of livestock organic waste at low hydraulic residence time (HRT).

    Science.gov (United States)

    Kuruti, Kranti; Nakkasunchi, Shalini; Begum, Sameena; Juntupally, Sudharshan; Arelli, Vijayalakshmi; Anupoju, Gangagni Rao

    2017-08-01

    The purpose of this study was to investigate the effect of pre-treatment and F/M (Food to Microorganism) ratios for the rapid generation of volatile fatty acids (VFA) from livestock organic wastes (cattle manure (CM) and poultry litter (PL)) through an anaerobic acidification process at a pH range of 4.5-5.5. Experiments were organized using CM and PL in batch reactors (1L and 25L) with and with no pre-treatment of substrate at F/M ratios (0.4, 0.6, 0.8 and 1). Among various existing pre-treatments methods, thermal-acidic (120°C; 1% H 2 SO 4 ) pre-treatment was found effective. The results revealed that 0.31 and 0.47kg VFA/(kg VS reduced) could be obtained from CM and PL respectively with no pre-treatment, whereas it improvised to 0.43 and 0.67kg VFA/(kg VS reduced) correspondingly due to pre-treatment. Aforesaid, better yield of VFA was obtained at F/M ratio of 1.0, pH-5.5 and hydraulic residence time of 4days. Copyright © 2017 Elsevier Ltd. All rights reserved.

  13. Performance linked to residence time distribution by a novel wool-based bioreactor for tertiary sewage treatment.

    Science.gov (United States)

    Hu, Bibo; Wheatley, Andrew; Ishtchenko, Vera; Huddersman, Katherine

    2012-05-01

    Laboratory-scale experiments were carried out using up-flow 7 L Submerged Aerated Filter reactors packed with wool fibre or commercial plastic pall rings, Kaldnes, (70% by volume) support media for the tertiary treatment of sewage. The performance of the wool bioreactor was more consistent than that with Kaldnes medium, for both TOC removal (93%) and SS removal (90%). Both plastic and wool-packed bioreactors achieved complete nitrification at the load of about 0.4 kgCOD/m(3)/day. The sludge yield of the wool bioreactor was almost half that of the bioreactor with Kaldnes suggesting that wool could retain residual organics and particulates. The wool however was degraded and it was concluded that wool would have to be considered as additional sacrificial adsorption capacity rather than an alternative medium. The performance was linked to the residence time distribution studies and these changes in the wool structure. Biomass growth increased the retention of the tracer in the wool reactor by, it was suggested, exposing a greater surface area. Results from the plastic media on the other hand showed increased mixing possibly by increasing the mobility of the plastic. Aeration increased the mixing in both reactors, and patterns were in all cases predominantly well-mixed.

  14. Contrasting residence times and fluxes of water and sulfate in two small forested watersheds in Virginia, USA.

    Science.gov (United States)

    Böhlke, John Karl; Michel, Robert L

    2009-07-01

    Watershed mass balances for solutes of atmospheric origin may be complicated by the residence times of water and solutes at various time scales. In two small forested headwater catchments in the Appalachian Mountains of Virginia, USA, mean annual export rates of SO(4)(=) differ by a factor of 2, and seasonal variations in SO(4)(=) concentrations in atmospheric deposition and stream water are out of phase. These features were investigated by comparing (3)H, (35)S, delta(34)S, delta(2)H, delta(18)O, delta(3)He, CFC-12, SF(6), and chemical analyses of open deposition, throughfall, stream water, and spring water. The concentrations of SO(4)(=) and radioactive (35)S were about twice as high in throughfall as in open deposition, but the weighted composite values of (35)S/S (11.1 and 12.1x10(-15)) and delta(34)S (+3.8 and +4.1 per thousand) were similar. In both streams (Shelter Run, Mill Run), (3)H concentrations and delta(34)S values during high flow were similar to those of modern deposition, delta(2)H and delta(18)O values exhibited damped seasonal variations, and (35)S/S ratios (0-3x10(-15)) were low throughout the year, indicating inter-seasonal to inter-annual storage and release of atmospheric SO(4)(=) in both watersheds. In the Mill Run watershed, (3)H concentrations in stream base flow (10-13 TU) were consistent with relatively young groundwater discharge, most delta(34)S values were approximately the same as the modern atmospheric deposition values, and the annual export rate of SO(4)(=) was equal to or slightly greater than the modern deposition rate. In the Shelter Run watershed, (3)H concentrations in stream base flow (1-3 TU) indicate that much of the discharging ground water had been deposited prior to the onset of atmospheric nuclear bomb testing in the 1950s, base flow delta(34)S values (+1.6 per thousand) were significantly lower than the modern deposition values, and the annual export rate of SO(4)(=) was less than the modern deposition rate

  15. Formation of Soot in Counterflow Diffusion Flames with Carbon Dioxide Dilution

    KAUST Repository

    Wang, Yu

    2016-05-04

    Experimental and numerical modeling studies have been performed to investigate the effect of CO2 dilution on soot formation in ethylene counterflow diffusion flames. Thermal and chemical effects of CO2 addition on soot growth was numerically identified by using a fictitious CO2 species, which was treated as inert in terms of chemical reactions. The results showed that CO2 addition reduces soot formation both thermodynamically and chemically. In terms of chemical effect, the addition of CO2 decreases soot formation through various pathways, including: (1) reduced soot precursor (PAH) formation leading to lower inception rates and soot number density, which in turn results in lower surface area for soot mass addition; (2) reduced H, CH3, and C3H3 concentrations causing lower H abstraction rate and therefore less active site per surface area for soot growth; and (3) reduced C2H2 mole fraction and thus a slower C2H2 mass addition rate. In addition, the sooting limits were also measured for ethylene counterflow flames in both N2 and CO2 atmosphere and the results showed that sooting region was significantly reduced in the CO2 case compared to the N2 case. © 2016 Taylor & Francis.

  16. Effects of Fuel Quantity on Soot Formation Process for Biomass-Based Renewable Diesel Fuel Combustion

    KAUST Repository

    Jing, Wei

    2016-12-01

    Soot formation process was investigated for biomass-based renewable diesel fuel, such as biomass to liquid (BTL), and conventional diesel combustion under varied fuel quantities injected into a constant volume combustion chamber. Soot measurement was implemented by two-color pyrometry under quiescent type diesel engine conditions (1000 K and 21% O2 concentration). Different fuel quantities, which correspond to different injection widths from 0.5 ms to 2 ms under constant injection pressure (1000 bar), were used to simulate different loads in engines. For a given fuel, soot temperature and KL factor show a different trend at initial stage for different fuel quantities, where a higher soot temperature can be found in a small fuel quantity case but a higher KL factor is observed in a large fuel quantity case generally. Another difference occurs at the end of combustion due to the termination of fuel injection. Additionally, BTL flame has a lower soot temperature, especially under a larger fuel quantity (2 ms injection width). Meanwhile, average soot level is lower for BTL flame, especially under a lower fuel quantity (0.5 ms injection width). BTL shows an overall low sooting behavior with low soot temperature compared to diesel, however, trade-off between soot level and soot temperature needs to be carefully selected when different loads are used.

  17. Molecular mechanics and quantum mechanical modeling of hexane soot structure and interactions with pyrene

    Directory of Open Access Journals (Sweden)

    Kubicki JD

    2000-09-01

    Full Text Available Molecular simulations (energy minimizations and molecular dynamics of an n-hexane soot model developed by Smith and co-workers (M. S. Akhter, A. R. Chughtai and D. M. Smith, Appl. Spectrosc., 1985, 39, 143; ref. 1 were performed. The MM+ (N. L. Allinger, J. Am. Chem. Soc., 1977, 395, 157; ref. 2 and COMPASS (H. Sun, J. Phys. Chem., 1998, 102, 7338; ref. 3 force fields were tested for their ability to produce realistic soot nanoparticle structure. The interaction of pyrene with the model soot was simulated. Quantum mechanical calculations on smaller soot fragments were carried out. Starting from an initial 2D structure, energy minimizations are not able to produce the observed layering within soot with either force field. Results of molecular dynamics simulations indicate that the COMPASS force field does a reasonably accurate job of reproducing observations of soot structure. Increasing the system size from a 683 to a 2732 atom soot model does not have a significant effect on predicted structures. Neither does the addition of water molecules surrounding the soot model. Pyrene fits within the soot structure without disrupting the interlayer spacing. Polycyclic aromatic hydrocarbons (PAH, such as pyrene, may strongly partition into soot and have slow desorption kinetics because the PAH-soot bonding is similar to soot–soot interactions. Diffusion of PAH into soot micropores may allow the PAH to be irreversibly adsorbed and sequestered so that they partition slowly back into an aqueous phase causing dis-equilibrium between soil organic matter and porewater.

  18. Strain rate effect on sooting characteristics in laminar counterflow diffusion flames

    KAUST Repository

    Wang, Yu

    2016-01-20

    The effects of strain rate, oxygen enrichment and fuel type on the sooting characteristics of counterflow diffusion flames were studied. The sooting structures and relative PAH concentrations were measured with laser diagnostics. Detailed soot modeling using recently developed PAH chemistry and surface reaction mechanism was performed and the results were compared with experimental data for ethylene flames, focusing on the effects of strain rates. The results showed that increase in strain rate reduced soot volume fraction, average size and peak number density. Increase in oxygen mole fraction increased soot loading and decreased its sensitivity on strain rate. The soot volume fractions of ethane, propene and propane flames were also measured as a function of global strain rate. The sensitivity of soot volume fraction to strain rate was observed to be fuel dependent at a fixed oxygen mole fraction, with the sensitivity being higher for more sooting fuels. However, when the soot loadings were matched at a reference strain rate for different fuels by adjusting oxygen mole fraction, the dependence of soot loading on strain rate became comparable among the tested fuels. PAH concentrations were shown to decrease with increase in strain rate and the dependence on strain rate is more pronounced for larger PAHs. Soot modeling was performed using detailed PAH growth chemistry with molecular growth up to coronene. A qualitative agreement was obtained between experimental and simulation results, which was then used to explain the experimentally observed strain rate effect on soot growth. However, quantitatively, the simulation result exhibits higher sensitivity to strain rate, especially for large PAHs and soot volume fractions.

  19. Whale shark (Rhincodon typus seasonal presence, residence time and habitat use at darwin island, galapagos marine reserve.

    Directory of Open Access Journals (Sweden)

    David Acuña-Marrero

    Full Text Available The life history of the whale shark (Rhincodon typus, including its reproductive ecology, still remains largely unknown. Here, we present results from the first whale shark population study around Darwin Island, Galapagos Marine Reserve. Following a diversified approach we characterized seasonal occurrence, population structure and size, and described habitat use of whale sharks based on fine scale movements around the island. Whale shark presence at Darwin Island was negatively correlated with Sea Surface Temperature (SST, with highest abundance corresponding to a cool season between July and December over six years of monitoring. From 2011 to 2013 we photo-identified 82 whale sharks ranging from 4 to 13.1 m Total Length (TL. Size distribution was bimodal, with a great majority (91.5% of adult female individuals averaging 11.35 m±0.12 m (TL±SE, all but one showing signs of a potential pregnancy. Population dynamics models for apparently pregnant sharks estimated the presence of 3.76±0.90 (mean ± SE sharks in the study area per day with an individual residence time of 2.09±0.51 (mean ± SE days. Movement patterns analysis of four apparently pregnant individuals tracked with acoustic tags at Darwin Island revealed an intense use of Darwin's Arch, where no feeding or specific behavior has been recorded, together with periodic excursions around the island's vicinity. Sharks showed a preference for intermediate depths (20-30 m with occasional dives mostly to mid-water, remaining the majority of their time at water temperatures between 24-25°C. All of our results point to Darwin Island as an important stopover in a migration, possibly with reproductive purposes, rather than an aggregation site. Current studies carried out in this area to investigate regional scale movement patterns may provide essential information about possible pupping grounds for this enigmatic species.

  20. Whale Shark (Rhincodon typus) Seasonal Presence, Residence Time and Habitat Use at Darwin Island, Galapagos Marine Reserve

    Science.gov (United States)

    Acuña-Marrero, David; Jiménez, Jesús; Smith, Franz; Doherty, Paul F.; Hearn, Alex; Green, Jonathan R.; Paredes-Jarrín, Jules; Salinas-de-León, Pelayo

    2014-01-01

    The life history of the whale shark (Rhincodon typus), including its reproductive ecology, still remains largely unknown. Here, we present results from the first whale shark population study around Darwin Island, Galapagos Marine Reserve. Following a diversified approach we characterized seasonal occurrence, population structure and size, and described habitat use of whale sharks based on fine scale movements around the island. Whale shark presence at Darwin Island was negatively correlated with Sea Surface Temperature (SST), with highest abundance corresponding to a cool season between July and December over six years of monitoring. From 2011 to 2013 we photo-identified 82 whale sharks ranging from 4 to 13.1 m Total Length (TL). Size distribution was bimodal, with a great majority (91.5%) of adult female individuals averaging 11.35 m±0.12 m (TL±SE), all but one showing signs of a potential pregnancy. Population dynamics models for apparently pregnant sharks estimated the presence of 3.76±0.90 (mean ± SE) sharks in the study area per day with an individual residence time of 2.09±0.51 (mean ± SE) days. Movement patterns analysis of four apparently pregnant individuals tracked with acoustic tags at Darwin Island revealed an intense use of Darwin's Arch, where no feeding or specific behavior has been recorded, together with periodic excursions around the island's vicinity. Sharks showed a preference for intermediate depths (20–30 m) with occasional dives mostly to mid-water, remaining the majority of their time at water temperatures between 24–25°C. All of our results point to Darwin Island as an important stopover in a migration, possibly with reproductive purposes, rather than an aggregation site. Current studies carried out in this area to investigate regional scale movement patterns may provide essential information about possible pupping grounds for this enigmatic species. PMID:25551553

  1. Use of multiple age tracers to estimate groundwater residence times and long-term recharge rates in arid southern Oman

    Science.gov (United States)

    Müller, Th.; Osenbrück, K.; Strauch, G.; Pavetich, S.; Al-Mashaikhi, K.-S.; Herb, C.; Merchel, S.; Rugel, G.; Aeschbach, W.; Sanford, Ward E.

    2016-01-01

    Multiple age tracers were measured to estimate groundwater residence times in the regional aquifer system underlying southwestern Oman. This area, known as the Najd, is one of the most arid areas in the world and is planned to be the main agricultural center of the Sultanate of Oman in the near future. The three isotopic age tracers 4He, 14C and 36Cl were measured in waters collected from wells along a line that extended roughly from the Dhofar Mountains near the Arabian Sea northward 400 km into the Empty Quarter of the Arabian Peninsula. The wells sampled were mostly open to the Umm Er Radhuma confined aquifer, although, some were completed in the mostly unconfined Rus aquifer. The combined results from the three tracers indicate the age of the confined groundwater is Mountains, > 100 ka in the central section north of the mountains, and up to and > one Ma in the Empty Quarter. The 14C data were used to help calibrate the 4He and 36Cl data. Mixing models suggest that long open boreholes north of the mountains compromise 14C-only interpretations there, in contrast to 4He and 36Cl calculations that are less sensitive to borehole mixing. Thus, only the latter two tracers from these more distant wells were considered reliable. In addition to the age tracers, δ2H and δ18O data suggest that seasonal monsoon and infrequent tropical cyclones are both substantial contributors to the recharge. The study highlights the advantages of using multiple chemical and isotopic data when estimating groundwater travel times and recharge rates, and differentiating recharge mechanisms.

  2. Whale shark (Rhincodon typus) seasonal presence, residence time and habitat use at darwin island, galapagos marine reserve.

    Science.gov (United States)

    Acuña-Marrero, David; Jiménez, Jesús; Smith, Franz; Doherty, Paul F; Hearn, Alex; Green, Jonathan R; Paredes-Jarrín, Jules; Salinas-de-León, Pelayo

    2014-01-01

    The life history of the whale shark (Rhincodon typus), including its reproductive ecology, still remains largely unknown. Here, we present results from the first whale shark population study around Darwin Island, Galapagos Marine Reserve. Following a diversified approach we characterized seasonal occurrence, population structure and size, and described habitat use of whale sharks based on fine scale movements around the island. Whale shark presence at Darwin Island was negatively correlated with Sea Surface Temperature (SST), with highest abundance corresponding to a cool season between July and December over six years of monitoring. From 2011 to 2013 we photo-identified 82 whale sharks ranging from 4 to 13.1 m Total Length (TL). Size distribution was bimodal, with a great majority (91.5%) of adult female individuals averaging 11.35 m±0.12 m (TL±SE), all but one showing signs of a potential pregnancy. Population dynamics models for apparently pregnant sharks estimated the presence of 3.76±0.90 (mean ± SE) sharks in the study area per day with an individual residence time of 2.09±0.51 (mean ± SE) days. Movement patterns analysis of four apparently pregnant individuals tracked with acoustic tags at Darwin Island revealed an intense use of Darwin's Arch, where no feeding or specific behavior has been recorded, together with periodic excursions around the island's vicinity. Sharks showed a preference for intermediate depths (20-30 m) with occasional dives mostly to mid-water, remaining the majority of their time at water temperatures between 24-25°C. All of our results point to Darwin Island as an important stopover in a migration, possibly with reproductive purposes, rather than an aggregation site. Current studies carried out in this area to investigate regional scale movement patterns may provide essential information about possible pupping grounds for this enigmatic species.

  3. Using stable isotopes to estimate and compare mean residence times in contrasting geologic catchments (Attert River, NW Luxembourg)

    Science.gov (United States)

    Martínez-Carreras, N.; Fenicia, F.; Frentress, J.; Wrede, S.; Pfister, L.

    2012-04-01

    In recent years, stable isotopes have been increasingly used to characterize important aspects of catchment hydrological functioning, such as water storage dynamics, flow pathways and water sources. These characteristics are often synthesized by the Mean Residence Time (MRT), which is a simple catchment descriptor that employ the relation of distinct stable isotopic signatures in the rainfall input and streamflow output of a catchment that are significantly dampened through sub-surface propagation. In this preliminary study, MRT was estimated in the Attert River catchment (NW Luxembourg), where previous studies have shown that lithology exerts a major control on runoff generation. The Attert catchment lies at the transition zone of contrasting bedrock lithology: the Northern part is characterized by Devonian schist of the Ardennes massif, while sedimentary deposits of sandstone and marls dominate in the south of the catchment. As a consequence of differing lithologic characteristics, hydrological processes change across scales. The schistose catchments exhibit a delayed shallow groundwater component, sandstone catchments have slow-responding year-round groundwater component, whereas flashy runoff regimes prevails in the marly catchments. Under these circumstances, the MRTs are expected to vary significantly according to lithology, and provide additional understanding in internal catchment processes and their scale dependencies. In order to test this, bi-weekly monitoring of rainfall and discharge stable water isotope composition (oxygen-18 and deuterium) has been carried out since 2007 in 10 nested sub-catchments ranging in size from 0.4 to 247 km2 in the Attert catchment. MRT was estimated using different lumped convolution integral models and sine wave functions with varying transit times distributions (TTDs). TTDs were evaluated through calibration. Further research efforts will deal with the application of conceptual models to simulate and compare TTD, using

  4. Automated determination of size and morphology information from soot transmission electron microscope (TEM)-generated images

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Cheng; Chan, Qing N., E-mail: qing.chan@unsw.edu.au; Zhang, Renlin; Kook, Sanghoon; Hawkes, Evatt R.; Yeoh, Guan H. [UNSW, School of Mechanical and Manufacturing Engineering (Australia); Medwell, Paul R. [The University of Adelaide, Centre for Energy Technology (Australia)

    2016-05-15

    The thermophoretic sampling of particulates from hot media, coupled with transmission electron microscope (TEM) imaging, is a combined approach that is widely used to derive morphological information. The identification and the measurement of the particulates, however, can be complex when the TEM images are of low contrast, noisy, and have non-uniform background signal level. The image processing method can also be challenging and time consuming, when the samples collected have large variability in shape and size, or have some degree of overlapping. In this work, a three-stage image processing sequence is presented to facilitate time-efficient automated identification and measurement of particulates from the TEM grids. The proposed processing sequence is first applied to soot samples that were thermophoretically sampled from a laminar non-premixed ethylene-air flame. The parameter values that are required to be set to facilitate the automated process are identified, and sensitivity of the results to these parameters is assessed. The same analysis process is also applied to soot samples that were acquired from an externally irradiated laminar non-premixed ethylene-air flame, which have different geometrical characteristics, to assess the morphological dependence of the proposed image processing sequence. Using the optimized parameter values, statistical assessments of the automated results reveal that the largest discrepancies that are associated with the estimated values of primary particle diameter, fractal dimension, and prefactor values of the aggregates for the tested cases, are approximately 3, 1, and 10 %, respectively, when compared with the manual measurements.

  5. Automated determination of size and morphology information from soot transmission electron microscope (TEM)-generated images

    International Nuclear Information System (INIS)

    Wang, Cheng; Chan, Qing N.; Zhang, Renlin; Kook, Sanghoon; Hawkes, Evatt R.; Yeoh, Guan H.; Medwell, Paul R.

    2016-01-01

    The thermophoretic sampling of particulates from hot media, coupled with transmission electron microscope (TEM) imaging, is a combined approach that is widely used to derive morphological information. The identification and the measurement of the particulates, however, can be complex when the TEM images are of low contrast, noisy, and have non-uniform background signal level. The image processing method can also be challenging and time consuming, when the samples collected have large variability in shape and size, or have some degree of overlapping. In this work, a three-stage image processing sequence is presented to facilitate time-efficient automated identification and measurement of particulates from the TEM grids. The proposed processing sequence is first applied to soot samples that were thermophoretically sampled from a laminar non-premixed ethylene-air flame. The parameter values that are required to be set to facilitate the automated process are identified, and sensitivity of the results to these parameters is assessed. The same analysis process is also applied to soot samples that were acquired from an externally irradiated laminar non-premixed ethylene-air flame, which have different geometrical characteristics, to assess the morphological dependence of the proposed image processing sequence. Using the optimized parameter values, statistical assessments of the automated results reveal that the largest discrepancies that are associated with the estimated values of primary particle diameter, fractal dimension, and prefactor values of the aggregates for the tested cases, are approximately 3, 1, and 10 %, respectively, when compared with the manual measurements.

  6. Impacts of fuel formulation and engine operating parameters on the nanostructure and reactivity of diesel soot

    Science.gov (United States)

    Yehliu, Kuen

    This study focuses on the impacts of fuel formulations on the reactivity and nanostructure of diesel soot. A 2.5L, 4-cylinder, turbocharged, common rail, direct injection light-duty diesel engine was used in generating soot samples. The impacts of engine operating modes and the start of combustion on soot reactivity were investigated first. Based on preliminary investigations, a test condition of 2400 rpm and 64 Nm, with single and split injection strategies, was chosen for studying the impacts of fuel formulation on the characteristics of diesel soot. Three test fuels were used: an ultra low sulfur diesel fuel (BP15), a pure soybean methyl-ester (B100), and a synthetic Fischer-Tropsch fuel (FT) produced in a gas-to-liquid process. The start of injection (SOI) and fuel rail pressures were adjusted such that the three test fuels have similar combustion phasing, thereby facilitating comparisons between soots from the different fuels. Soot reactivity was investigated by thermogravimetric analysis (TGA). According to TGA, B100 soot exhibits the fastest oxidation on a mass basis followed by BP15 and FT derived soots in order of apparent rate constant. X-ray photoelectron spectroscopy (XPS) indicates no relation between the surface oxygen content and the soot reactivity. Crystalline information for the soot samples was obtained using X-ray diffraction (XRD). The basal plane diameter obtained from XRD was inversely related to the apparent rate constants for soot oxidation. For comparison, high resolution transmission electron microscopy (HRTEM) provided images of the graphene layers. Quantitative image analysis proceeded by a custom algorithm. B100 derived soot possessed the shortest mean fringe length and greatest mean fringe tortuosity. This suggests soot (nano)structural disorder correlates with a faster oxidation rate. Such results are in agreement with the X-ray analysis, as the observed fringe length is a measure of basal plane diameter. Moreover the relation

  7. Blue light emitting diesel soot for photonic applications

    Science.gov (United States)

    Swapna, M. S.; Sankararaman, S.

    2018-01-01

    The present work is the first report of producing blue light emission from phosphor free and low-cost material—the diesel soot from the internal combustion engines (ICEs). The structural morphology is analyzed by field emission scanning electron microscopy and high-resolution transmission electron microscopy. The optical characterization is done by recording UV–visible spectrum and photoluminescent Spectrum. The CIE plot and the power spectrum for the sample show blue emission. This is further verified by collecting diesel soot from the ICE of different year of make. A visual confirmation of blue emission is obtained by exciting the sample with UV laser. The presence of various allotropic forms of carbon in the sample is identified by x-ray diffraction, Fourier transform infrared and Raman spectroscopic analysis.

  8. Soot in the atmosphere and snow surface of Antarctica

    International Nuclear Information System (INIS)

    Warren, S.G.; Clarke, A.D.

    1990-01-01

    Samples of snow collected near the south pole during January and February 1986 were analyzed for the presence of light-absorbing particles by passing the melted snow through a nuclepore filter. Transmission of light through the filter showed that snow far from the station contains the equivalent of 0.1-0.3 ng of carbon per gram of snow (ng/g). Samples of ambient air were filtered and found to contain about 1-2 ng of carbon per kilogram of air, giving a scavenging ratio of about 150. The snow downwind of the station exhibited a well-defined plume of soot due to the burning of diesel fuel, but even in the center of the plume 1 km downwind, the soot concentration was only 3 ng/g, too small to affect snow albedo significantly. Measurements of snow albedo near large inland stations are therefore probably representative of their surrounding regions

  9. Temperature and velocity profiles in sooting free boundary layer flames

    Science.gov (United States)

    Ang, J. A.; Pagni, P. J.; Mataga, T. G.; Margle, J. M.; Lyons, V. J.

    1986-01-01

    Temperature and velocity profiles are presented for cyclohexane, n-heptane, and iso-octane free, laminar, boundary layer, sooting, diffusion flames. Temperatures are measured with 3 mil Pt/Pt-13 percent Rh thermocouples. Corrected gas temperatures are derived by performing an energy balance of convection to and radiation from the thermocouple bead incorporating the variation of air conductivity and platinum emissivity with temperature. Velocities are measured using laser doppler velocimetry techniques. Profiles are compared with previously reported analytic temperature and velocity fields. Comparison of theoretical and experimental temperature profiles suggests improvement in the analytical treatment is needed, which accounts more accurately for the local soot radiation. The velocity profiles are in good agreement, with the departure of the theory from observation partially due to the small fluctuations inherent in these free flows.

  10. Single Particle Soot Photometer intercomparison at the AIDA chamber

    Directory of Open Access Journals (Sweden)

    M. Laborde

    2012-12-01

    Full Text Available Soot particles, consisting of black carbon (BC, organic carbon (OC, inorganic salts, and trace elements, are emitted into the atmosphere during incomplete combustion. Accurate measurements of atmospheric BC are important as BC particles cause adverse health effects and impact the climate.

    Unfortunately, the accurate measurement of the properties and mass concentrations of BC particles remains difficult. The Single Particle Soot Photometer (SP2 can contribute to improving this situation by measuring the mass of refractory BC in individual particles as well as its mixing state.

    Here, the results of the first detailed SP2 intercomparison, involving 6 SP2s from 6 different research groups, are presented, including the most evolved data products that can presently be calculated from SP2 measurements.

    It was shown that a detection efficiency of almost 100% down to 1 fg BC per particle can readily be achieved, and that this limit can be pushed down to ∼0.2 fg BC with optimal SP2 setup. Number and mass size distributions of BC cores agreed within ±5% and ±10%, respectively, in between the SP2s, with larger deviations in the range below 1 fg BC.

    The accuracy of the SP2's mass concentration measurement depends on the calibration material chosen. The SP2 has previously been shown to be equally sensitive to fullerene soot and ambient BC from sources where fossil fuel was dominant and less sensitive to fullerene soot than to Aquadag. Fullerene soot was therefore chosen as the standard calibration material by the SP2 user community; however, many data sets rely solely on Aquadag calibration measurements. The difference in SP2 sensitivity was found to be almost equal (fullerene soot to Aquadag response ratio of ∼0.75 at 8.9 fg BC for all SP2s. This allows the calculation of a fullerene soot equivalent calibration curve from a measured Aquadag calibration, when no fullerene soot calibration is available. It could be

  11. Hydrodynamic features of centrifugal contactor separators; experimental studies on liquid hold-up, residence time distribution, phase behavior and drop size distributions

    NARCIS (Netherlands)

    Schuur, Boelo; Kraai, G.N.; Winkelman, J.G.N.; Heeres, H.

    2012-01-01

    The liquid hold-up, residence time distributions (RTD), drop size distributions and continuous/dispersed phase for a typical centrifugal contactor separator (CCS) of the type CINC V02 were determined experimentally for various L-L systems. The hold-up ratio of the different solvents was mainly a

  12. Hydrodynamic features of centrifugal contactor separators : Experimental studies on liquid hold-up, residence time distribution, phase behavior and drop size distributions

    NARCIS (Netherlands)

    Schuur, Boelo; Kraai, Gerard N.; Winkelman, Jozef G. M.; Heeres, Hero J.

    The liquid hold-up, residence time distributions (RTD), drop size distributions and continuous/dispersed phase for a typical centrifugal contactor separator (CCS) of the type CINC V02 were determined experimentally for various L-L systems. The hold-up ratio of the different solvents was mainly a

  13. Systematic Analysis of the Effect of Small Scale Permeability Heterogeneity on Hyporheic Exchange Flux and Residence Times

    Science.gov (United States)

    Laube, G.; Schmidt, C.; Fleckenstein, J. H.

    2014-12-01

    The hyporheic zone (HZ) contributes significantly to whole stream biogeochemical cycling. Biogeochemical reactions within the HZ are often transport limited, thus, understanding these reactions requires knowledge about the magnitude of hyporheic fluxes (HF) and the residence time (RT) of these fluxes within the HZ. While the hydraulics of HF are relatively well understood, studies addressing the influence of permeability heterogeneity lack systematic analysis and have even produced contradictory results (e.g. [1] vs. [2]). In order to close this gap, this study uses a statistical numerical approach to elucidate the influence of permeability heterogeneity on HF and RT. We simulated and evaluated 3750 2D-scenarios of sediment heterogeneity by means of Gaussian random fields with focus on total HF and RT distribution. The scenarios were based on ten realizations of each of all possible combinations of 15 different correlation lengths, 5 dipping angles and 5 permeability variances. Roughly 500 hyporheic stream traces were analyzed per simulation, for a total of almost two million stream traces analyzed for correlations between permeability heterogeneity, HF, and RT. Total HF and the RT variance positively correlated with permeability variance while the mean RT negatively correlated with permeability variance. In contrast, changes in correlation lengths and dipping angles had little effect on the examined properties RT and HF. These results provide a possible explanation of the seemingly contradictory conclusions of recent studies, given that the permeability variances in these studies differ by several orders of magnitude. [1] Bardini, L., Boano, F., Cardenas, M.B, Sawyer, A.H, Revelli, R. and Ridolfi, L. "Small-Scale Permeability Heterogeneity Has Negligible Effects on Nutrient Cycling in Streambeds." Geophysical Research Letters, 2013. doi:10.1002/grl.50224. [2] Zhou, Y., Ritzi, R. W., Soltanian, M. R. and Dominic, D. F. "The Influence of Streambed Heterogeneity on

  14. Residence time of carbon substrate for autotrophic respiration of a grassland ecosystem correlates with the carbohydrate status of its vegetation

    Science.gov (United States)

    Ostler, Ulrike; Lehmeier, Christoph A.; Schleip, Inga; Schnyder, Hans

    2016-04-01

    Ecosystem respiration is composed of two component fluxes: (1) autotrophic respiration, which comprises respiratory activity of plants and plant-associated microbes that feed on products of recent photosynthetic activity and (2) heterotrophic respiration of microbes that decompose organic matter. The mechanistic link between the availability of carbon (C) substrate for ecosystem respiration and its respiratory activity is not well understood, particularly in grasslands. Here, we explore, how the kinetic features of the supply system feeding autotrophic ecosystem respiration in a temperate humid pasture are related to the content of water-soluble carbohydrates and remobilizable protein (as potential respiratory substrates) in vegetation biomass. During each September 2006, May 2007 and September 2007, we continuously labeled 0.8 m2 pasture plots with 13CO2/12CO2 and observed ecosystem respiration and its tracer content every night during the 14-16 day long labeling periods. We analyzed the tracer kinetics with a pool model, which allowed us to precisely partition ecosystem respiration into its autotrophic and heterotrophic flux components. At the end of a labeling campaign, we harvested aboveground and belowground plant biomass and analyzed its non-structural C contents. Approximately half of ecosystem respiration did not release any significant amount of tracer during the labeling period and was hence characterized as heterotrophic. The other half of ecosystem respiration was autotrophic, with a mean residence time of C in the respiratory substrate pool between 2 and 6 d. Both the rate of autotrophic respiration and the turnover of its substrate supply pool were correlated with plant carbohydrate content, but not with plant protein content. These findings are in agreement with studies in controlled environments that revealed water-soluble carbohydrates as the main substrate and proteins as a marginal substrate for plant respiration under favorable growth conditions

  15. Effect of temperature, hydraulic residence time and elevated PCO2 on acid neutralization within a pulsed limestone bed reactor

    Science.gov (United States)

    Watten, B.J.; Lee, P.C.; Sibrell, P.L.; Timmons, M.B.

    2007-01-01

    Limestone has potential for reducing reagent costs and sludge volume associated with treatment of acid mine drainage, but its use is restricted by slow dissolution rates and the deposition of Fe, Al and Mn-based hydrolysis products on reactive surfaces. We evaluated a pulsed limestone bed (PLB) reactor (15 L/min capacity) that uses a CO2 pretreatment step to accelerate dissolution and hydraulic shearing forces provided by intermittent fluidization to abrade and carry away surface scales. We established the effects of hydraulic residence time (HRT, 5.1-15.9 min), temperature (T, 12-22 ??C) and CO2 tension (PCO2, 34.5-206.8 kPa) on effluent quality when inlet acidity (Acy) was fixed at 440 mg/L (pH=2.48) with H2SO4. The PLB reactor neutralized all H+ acidity (N=80) while concurrently providing unusually high levels of effluent alkalinity (247-1028 mg/L as CaCO3) that allow for side-stream treatment with blending. Alkalinity (Alk) yields rose with increases in PCO2, HRT and settled bed height (BH, cm) and decreased with T following the relationship (R2=0.926; p<0.001): (Alk)non-filtered=-548.726+33.571??(PCO2)0.5+33.671??(HRT)+7.734??(BH)-5.197??(T). Numerical modeling showed CO2 feed requirements for a target Alk yield decrease with increases in HRT, T and the efficiency of off-gas (CO2) recycling. ?? 2007 Elsevier Ltd. All rights reserved.

  16. Investigation of soot optical properties by spectral line-of-sight attenuation

    Energy Technology Data Exchange (ETDEWEB)

    Migliorini, F.; Thomson, K.A.; Smallwood, G.J. [National Research Council of Canada, Ottawa, ON (Canada); Geigle, K.P. [DLR, Stuttgart (Germany). Inst. of Combustion Technology; Johnson, M.J. [Carleton Univ., Ottawa, ON (Canada)

    2009-07-01

    Optical soot diagnostics are a non-intrusive method to measure, understand and hopefully control soot formation. This presentation discussed an investigation of soot optical properties by spectral line-of-sight attenuation. Topics that were presented included optical properties in soot diagnostics; the soot refractive index absorption function E(m); E(m) from the literature; variation of E(m) with wavelength; governing equations; one-dimensional spectral LOSA; the gulder burner; the McKenna burner; zero-dimensional spectral LOSA; relative E(m) for the McKenna burner; and a discussion on relative E(m) in a McKenna flame. It was concluded that future work should include thermophoretic sampling at measurement locations in Gulder and McKenna burner to establish morphology and aging of soot and emission measurements to determine if multi-wavelength pyrometry agrees with multiwavelength attenuation. figs.

  17. Effects of morphology and wavelength on the measurement accuracy of soot volume fraction by laser extinction

    Science.gov (United States)

    Wang, Ya-fei; Huang, Qun-xing; Wang, Fei; Chi, Yong; Yan, Jian-hua

    2018-01-01

    A novel method to evaluate the quantitative effects of soot morphology and incident wavelength on the measurement accuracy of soot volume fraction, by the laser extinction (LE) technique is proposed in this paper. The results indicate that the traditional LE technique would overestimate soot volume fraction if the effects of morphology and wavelength are not considered. Before the agglomeration of isolated soot primary particles, the overestimation of the LE technique is in the range of 2-20%, and rises with increasing primary particle diameter and with decreasing incident wavelength. When isolated primary particles are agglomerated into fractal soot aggregates, the overestimation would exceed 30%, and rise with increasing primary particle number per soot aggregate, fractal dimension and fractal prefactor and with decreasing incident wavelength to a maximum value of 55%. Finally, based on these results above, the existing formula of the LE technique gets modified, and the modification factor is 0.65-0.77.

  18. Conductometric Sensor for Soot Mass Flow Detection in Exhausts of Internal Combustion Engines.

    Science.gov (United States)

    Feulner, Markus; Hagen, Gunter; Müller, Andreas; Schott, Andreas; Zöllner, Christian; Brüggemann, Dieter; Moos, Ralf

    2015-11-13

    Soot sensors are required for on-board diagnostics (OBD) of automotive diesel particulate filters (DPF) to detect filter failures. Widely used for this purpose are conductometric sensors, measuring an electrical current or resistance between two electrodes. Soot particles deposit on the electrodes, which leads to an increase in current or decrease in resistance. If installed upstream of a DPF, the "engine-out" soot emissions can also be determined directly by soot sensors. Sensors were characterized in diesel engine real exhausts under varying operation conditions and with two different kinds of diesel fuel. The sensor signal was correlated to the actual soot mass and particle number, measured with an SMPS. Sensor data and soot analytics (SMPS) agreed very well, an impressing linear correlation in a double logarithmic representation was found. This behavior was even independent of the used engine settings or of the biodiesel content.

  19. Time to reach tacrolimus maximum blood concentration,mean residence time, and acute renal allograft rejection: an open-label, prospective, pharmacokinetic study in adult recipients.

    Science.gov (United States)

    Kuypers, Dirk R J; Vanrenterghem, Yves

    2004-11-01

    The aims of this study were to determine whether disposition-related pharmacokinetic parameters such as T(max) and mean residence time (MRT) could be used as predictors of clinical efficacy of tacrolimus in renal transplant recipients, and to what extent these parameters would be influenced by clinical variables. We previously demonstrated, in a prospective pharmacokinetic study in de novo renal allograft recipients, that patients who experienced early acute rejection did not differ from patients free from rejection in terms of tacrolimus pharmacokinetic exposure parameters (dose interval AUC, preadministration trough blood concentration, C(max), dose). However, recipients with acute rejection reached mean (SD) tacrolimus T(max) significantly faster than those who were free from rejection (0.96 [0.56] hour vs 1.77 [1.06] hours; P clearance nor T(1/2) could explain this unusual finding, we used data from the previous study to calculate MRT from the concentration-time curves. As part of the previous study, 100 patients (59 male, 41 female; mean [SD] age, 51.4 [13.8] years;age range, 20-75 years) were enrolled in the study The calculated MRT was significantly shorter in recipients with acute allograft rejection (11.32 [031] hours vs 11.52 [028] hours; P = 0.02), just like T(max) was an independent risk factor for acute rejection in a multivariate logistic regression model (odds ratio, 0.092 [95% CI, 0.014-0.629]; P = 0.01). Analyzing the impact of demographic, transplantation-related, and biochemical variables on MRT, we found that increasing serum albumin and hematocrit concentrations were associated with a prolonged MRT (P calculated MRT were associated with a higher incidence of early acute graft rejection. These findings suggest that a shorter transit time of tacrolimus in certain tissue compartments, rather than failure to obtain a maximum absolute tacrolimus blood concentration, might lead to inadequate immunosuppression early after transplantation.

  20. In-situ burning of heavy oils and Orimulsion : analysis of soot and residue

    International Nuclear Information System (INIS)

    Fingas, M.F.; Wang, Z.; Fieldhouse, B.; Brown, C.E.; Yang, C.; Landriault, M.

    2005-01-01

    Oil spilled on water can be cleaned up by in-situ burning which can rapidly reduce the volume of spilled oil and eliminate the need to collect, store, transport and dispose of recovered oil. In-situ burning also shortens the response time to an oil spill, preventing the oil from reaching shorelines and thereby protecting the environment and aquatic biota. However, the concern over atmospheric emissions is the greatest barrier to the widespread use of in-situ burning. In this study, a series of bench-scale in-situ burning tests were conducted on Bunker C, Orimulsion and bitumen in order to analyze the residue and soot to gain insight into the chemistry of burning. The maximum burn efficiency was 70 per cent and the residue was mostly asphaltenes and resins which solidified when cooled. Soot was collected from glass-fibre filters on a sampling pump and the extracts were analyzed for polyaromatic hydrocarbons (PAHs). The analysis revealed that PAHs are enriched in pyrogenic PAHs and derive from the petrogenic PAHs in the starting oils. The PAH content is less than in many other environmental impacts. The solid residues were also analyzed for saturates of aromatics resins and asphaltenes (SARA). Their viscosity was also measured. The SARA analysis of the residue demonstrates that most of the heavy components such as the resins and asphaltenes are not burned by the fire, but are accumulated in the residue. 7 refs., 8 tabs., 6 figs

  1. A proposed solution to integrating cognitive-affective neuroscience and neuropsychiatry in psychiatry residency training: The time is now.

    Science.gov (United States)

    Torous, John; Stern, Adam P; Padmanabhan, Jaya L; Keshavan, Matcheri S; Perez, David L

    2015-10-01

    Despite increasing recognition of the importance of a strong neuroscience and neuropsychiatry education in the training of psychiatry residents, achieving this competency has proven challenging. In this perspective article, we selectively discuss the current state of these educational efforts and outline how using brain-symptom relationships from a systems-level neural circuit approach in clinical formulations may help residents value, understand, and apply cognitive-affective neuroscience based principles towards the care of psychiatric patients. To demonstrate the utility of this model, we present a case of major depressive disorder and discuss suspected abnormal neural circuits and therapeutic implications. A clinical neural systems-level, symptom-based approach to conceptualize mental illness can complement and expand residents' existing psychiatric knowledge. Copyright © 2015 Elsevier B.V. All rights reserved.

  2. Effects of carbon dioxide on isolated droplet combustion for sooting and non-sooting fuels in microgravity

    Science.gov (United States)

    Nakaya, Shinji; Furuta, Tomoya; Nagashima, Yoshiaki; Segawa, Daisuke; Kadota, Toshikazu

    The combustion behavior of ethanol, n-buthanol and n-decane droplets in high concentration of CO2 was experimentally investigated at atmospheric pressure in microgravity. Experiments were performed during a fall of the experimental setup at 1 s drop tower with the total height of 9 m. The initial droplet diameter was ranged from about 0.3 to 0.8 mm. Detail measurements of the projected image of the droplet are conducted by using a high speed video camera and the effective droplet diameter squared are calculated from the surface area of the rotating body of the projected object. Effects of ambient carbon dioxide on unsteady behavior of the instantaneous burning rate for sooting and non-sooting droplet flames were investigated. The behavior of the instantaneous burning rate clearly showed events of the initial thermal expansion, ignition and subsequent burning of the fuel droplet, and it was different from the behavior predicted by d2 law. These fundamental behaviors for ethanol, n-buthanol and n-decane were shown in air and high concentrations of ambient carbon dioxide. In the case of n-decane (sooting fuel), the change in the burning rate after ignition was great while it was small in the case of ethanol. A stepwise increase in the burning rate after ignition could be clearly seen for n-decane droplet when initial droplet diameter was large although the tendency was not observed for ethanol. However, this stepwise behavior disappeared in high concentration of ambient carbon dioxide. In high concentration of ambient carbon dioxide, non-luminous flame was formed. The mitigation of soot production by ambient carbon dioxide was clearly observed and this effect was greater for the smaller droplet.

  3. Correlation of Soot Formation in Turbojet Engines and in Laboratory Flames.

    Science.gov (United States)

    1981-02-01

    tendency of a fuel to soot (cf. Refs. 18 and 19); for Bunsen burner flames the calculated adiabatic flame temperatures at the incipient soot point... flame burner is used to measure the smoke point. An objection can also be made to using a smoke point defined by using small laboratory diffusion...in Appendix A, it is possible to calibrate a wide variety of laboratory-scale diffusion or premixed flame burners so that if soot thresh- olds for a

  4. Numerical modeling of soot formation in a turbulent C2H4/air diffusion flame

    Directory of Open Access Journals (Sweden)

    Manedhar Reddy Busupally

    2016-06-01

    Full Text Available Soot formation in a lifted C2H4-Air turbulent diffusion flame is studied using two different paths for soot nucleation and oxidation; by a 2D axisymmetric RANS simulation using ANSYS FLUENT 15.0. The turbulence-chemistry interactions are modeled using two different approaches: steady laminar flamelet approach and flamelet-generated manifold. Chemical mechanism is represented by POLIMI to study the effect of species concentration on soot formation. P1 approximation is employed to approximate the radiative transfer equation into truncated series expansion in spherical harmonics while the weighted sum of gray gases is invoked to model the absorption coefficient while the soot model accounts for nucleation, coagulation, surface growth, and oxidation. The first route for nucleation considers acetylene concentration as a linear function of soot nucleation rate, whereas the second route considers two and three ring aromatic species as function of nucleation rate. Equilibrium-based and instantaneous approach has been used to estimate the OH concentration for soot oxidation. Lee and Fenimore-Jones soot oxidation models are studied to shed light on the effect of OH on soot oxidation. Moreover, the soot-radiation interactions are also included in terms of absorption coefficient of soot. Furthermore, the soot-turbulence interactions have been invoked using a temperature/mixture fraction-based single variable PDF. Both the turbulence-chemistry interaction models are able to accurately predict the flame liftoff height, and for accurate prediction of flame length, radiative heat loss should be accounted in an accurate way. The soot-turbulence interactions are found sensitive to the PDF used in present study.

  5. Resident resistance.

    Science.gov (United States)

    Price, J L; Cleary, B

    1999-01-01

    Clearly, faculty must work hard with residents to explore the nature of their resistance to a program's learning and growth opportunities. Initial steps to a deeper, more effective, and longer-lasting change process must be pursued. If resident resistance is mishandled or misunderstood, then learning and professional growth may be sidetracked and the purposes of residency training defeated. Listening to the whole person of the resident and avoiding the trap of getting caught up in merely responding to select resident behaviors that irritate us is critical. Every faculty member in the family practice residency program must recognize resistance as a form of defense that cannot immediately be torn down or taken away. Resident defenses have important purposes to play in stress reduction even if they are not always healthy. Residents, especially interns, use resistance to avoid a deeper and more truthful look at themselves as physicians. A family practice residency program that sees whole persons in their residents and that respects resident defenses will effectively manage the stress and disharmony inherent to the resistant resident.

  6. Tracer test modeling for characterizing heterogeneity and local scale residence time distribution in an artificial recharge site.

    Science.gov (United States)

    Valhondo, Cristina; Martinez-Landa, Lurdes; Carrera, Jesús; Hidalgo, Juan J.; Ayora, Carlos

    2017-04-01

    Artificial recharge of aquifers (AR) is a standard technique to replenish and enhance groundwater resources, that have widely been used due to the increasing demand of quality water. AR through infiltration basins consists on infiltrate surface water, that might be affected in more or less degree by treatment plant effluents, runoff and others undesirables water sources, into an aquifer. The water quality enhances during the passage through the soil and organic matter, nutrients, organic contaminants, and bacteria are reduced mainly due to biodegradation and adsorption. Therefore, one of the goals of AR is to ensure a good quality status of the aquifer even if lesser quality water is used for recharge. Understand the behavior and transport of the potential contaminants is essential for an appropriate management of the artificial recharge system. The knowledge of the flux distribution around the recharge system and the relationship between the recharge system and the aquifer (area affected by the recharge, mixing ratios of recharged and native groundwater, travel times) is essential to achieve this goal. Evaluate the flux distribution is not always simple because the complexity and heterogeneity of natural systems. Indeed, it is not so much regulate by hydraulic conductivity of the different geological units as by their continuity and inter-connectivity particularly in the vertical direction. In summary for an appropriate management of an artificial recharge system it is needed to acknowledge the heterogeneity of the media. Aiming at characterizing the residence time distribution (RTDs) of a pilot artificial recharge system and the extent to which heterogeneity affects RTDs, we performed and evaluated a pulse injection tracer test. The artificial recharge system was simulated as a multilayer model which was used to evaluate the measured breakthrough curves at six monitoring points. Flow and transport parameters were calibrated under two hypotheses. The first

  7. SU-E-T-45: Antibody Mean Residence Time in Blood and Its Correlation with Protein Molecular Weight

    Energy Technology Data Exchange (ETDEWEB)

    Kwok, C; Williams, L [Retired from City of Hope Medical Center, Arcadia, CA (United States)

    2014-06-01

    Purpose: Animal biodistribution data are required prior to introducing a new radiopharmaceutical into clinical trials. Protein engineering, using recombinant DNA techniques can produce a large number of related (cognate) antibodies to a given molecular target. Thus, it is important that these constructs be numerically related to one another via a single criterion. In the following, we use the mean residence time (MRT) in murine blood as this criterion. Methods: Five cognate anti-CEA (Carcinoembryonic Antigen) antibodies were compared with regard to their MRT in whole blood of CEA-positive tumor-bearing (LS174T) mice. MRT was defined by blood AUC (area under the curve) divided by the