WorldWideScience

Sample records for research support three-phase

  1. Research on three-phase unbalanced distribution network reconfiguration strategy

    Science.gov (United States)

    Hu, Shuang; Li, Ke-Jun; Xu, Yanshun; Liu, Zhijie; Guo, Jing; Wang, Zhuodi

    2017-01-01

    With the development of social economy, the loads installed in the distribution network become more and more complex which may cause the three-phase unbalance problems. This paper proposes an optimal reconfiguration approach based on mixed integer quadric programming (MIQP) method to address the three-phase unbalance problem. It aims to minimize the total network losses of the system. By using several square constraints to substitute the circular constraint, the original optimization problem is linearized and converted into a mixed-integer linear programming (MILP) model. Then this MILP problem is solved in general algebraic model system (GAMS) software using CPLEX solver. The additional losses caused by three-phase unbalanced are also considered. An IEEE 34 nodes test system is used to demonstrate the feasibility and effectiveness of the proposed method. The results show that the losses and the voltage violation mitigation in the network can be reduced significantly.

  2. Power coordinated control method with frequency support capability for hybrid single/three-phase microgrid

    DEFF Research Database (Denmark)

    Zhou, Xiaoping; Chen, Yandong; Zhou, Leming

    2018-01-01

    storage unit (ESU) are added into hybrid single/three-phase microgrid, and a power coordinated control method with frequency support capability is proposed for hybrid single/three-phase microgrid in this study. PEU is connected with three single-phase microgrids to coordinate power exchange among three...... phases and provide frequency support for hybrid microgrid. Meanwhile, a power coordinated control method based on the droop control is proposed for PEU to alleviate three-phase power imbalance and reduce voltage fluctuation of hybrid microgrid. Besides, ESU is injected into the DC-link to buffer......Due to the intermittent output power of distributed generations (DGs) and the variability of loads, voltage fluctuation and three-phase power imbalance easily occur when hybrid single/three-phase microgrid operates in islanded mode. To address these issues, the power exchange unit (PEU) and energy...

  3. Flexible voltage support control for three-phase distributed generation inverters under grid fault

    DEFF Research Database (Denmark)

    Camacho, Antonio; Castilla, Miguel; Miret, Jaume

    2013-01-01

    Operators describe the behavior of the energy source, regulating voltage limits and reactive power injection to remain connected and support the grid under fault. On the basis that different kinds of voltage sags require different voltage support strategies, a flexible control scheme for three phase grid...... connected inverters is proposed. In three phase balanced voltage sags, the inverter should inject reactive power in order to raise the voltage in all phases. In one or two phase faults, the main concern of the distributed generation inverter is to equalize voltages by reducing the negative symmetric...... sequence and clear the phase jump. Due to system limitations, a balance between these two extreme policies is mandatory. Thus, over-voltage and undervoltage can be avoided, and the proposed control scheme prevents disconnection while achieving the desired voltage support service. The main contribution...

  4. Teaching Qualitative Research for Human Services Students: A Three-Phase Model

    Science.gov (United States)

    Goussinsky, Ruhama; Reshef, Arie; Yanay-Ventura, Galit; Yassour-Borochowitz, Dalit

    2011-01-01

    Qualitative research is an inherent part of the human services profession, since it emphasizes the great and multifaceted complexity characterizing human experience and the sociocultural context in which humans act. In the department of human services at Emek Yezreel College, Israel, we have developed a three-phase model to ensure a relatively…

  5. Design Research on Three-Phase PWM Rectifier Based on Double Closed Loop Control Technology

    Directory of Open Access Journals (Sweden)

    Guang Ya LIU

    2014-02-01

    Full Text Available Based on the high frequency of three-phase voltage source PWM rectifier, this paper established a mathematical model of three phase current inner ring and outer ring voltage, and put forward the setting method of three phase double closed loop control. Finally, it was verified through simulation. The experimental results show that Three-phase output of DC voltage is stable with the operation of regulating systems, the current flowing into the grid tends to be sinusoidal and power factor is close to 1, which greatly reduce the interference of harmonics on the grid, thus improve grid operation.

  6. Research on Control System of Three - phase Brushless DC Motor for Electric Vehicle

    Science.gov (United States)

    Wang, Zhiwei; Jin, Hai; Guo, Jie; Su, Jie; Wang, Miao

    2017-12-01

    In order to study the three-phase brushless motor control system of electric vehicle, Freescale9S12XS128 chip is used as the control core, and the power MOSFET is used as the inverter device. The software is compiled by Codewarrior software. The speed control link adopts open-loop control, and the control chip collects the external sensor signal voltage Change control PWM signal output control three-phase brushless DC motor speed. The whole system consists of Hall position detection module, current detection module, power drive module and voltage detection module. The basic functions of three-phase brushless DC motor drive control are realized.

  7. Research on a Compound Control Strategy of Three-Phase Inverter for Unbalanced Loads

    Directory of Open Access Journals (Sweden)

    Yue Gaili

    2017-01-01

    Full Text Available To solve the problem of unbalanced output voltage of inverter under three-phase unbalanced load. In this paper, the main circuit topology using three-phase three-wire inverter topology. Established the mathematical model in several different coordinate system of the three-phase inverter. A compound control method is proposed by combining voltage current dual loop control method and repetitive control method, The control method is realized in three - phase 400 Hz inverter, and can meet the demand of unbalanced load to inverter, the reliability of the inverter circuit is improved. At the end of this paper, Matlab simulation analysis and experimental results are given, it is proved that the composite control method designed in this paper has a strong ability of unbalanced load.

  8. Data in support of three phase partitioning of zingibain, a milk-clotting enzyme from Zingiber officinale Roscoe rhizomes

    Science.gov (United States)

    Gagaoua, Mohammed; Hafid, Kahina; Hoggas, Naouel

    2016-01-01

    This paper describes data related to a research article titled “Three Phase Partitioning of zingibain, a milk-clotting enzyme from Zingiber officinale Roscoe rhizomes” (Gagaoua et al., 2015) [1]. Zingibain (EC 3.4.22.67), is a coagulant cysteine protease and a meat tenderizer agent that have been reported to produce satisfactory final products in dairy and meat technology, respectively. Zingibains were exclusively purified using chromatographic techniques with very low yield purification. This paper includes data of the effect of temperature, usual salts and organic solvents on the efficiency of the three phase partitioning (TPP) system. Also it includes data of the kinetic activity characterization of the purified zingibain using TPP purification approach. PMID:26909379

  9. Research on three-phase traffic flow modeling based on interaction range

    Science.gov (United States)

    Zeng, Jun-Wei; Yang, Xu-Gang; Qian, Yong-Sheng; Wei, Xu-Ting

    2017-12-01

    On the basis of the multiple velocity difference effect (MVDE) model and under short-range interaction, a new three-phase traffic flow model (S-MVDE) is proposed through careful consideration of the influence of the relationship between the speeds of the two adjacent cars on the running state of the rear car. The random slowing rule in the MVDE model is modified in order to emphasize the influence of vehicle interaction between two vehicles on the probability of vehicles’ deceleration. A single-lane model which without bottleneck structure under periodic boundary conditions is simulated, and it is proved that the traffic flow simulated by S-MVDE model will generate the synchronous flow of three-phase traffic theory. Under the open boundary, the model is expanded by adding an on-ramp, the congestion pattern caused by the bottleneck is simulated at different main road flow rates and on-ramp flow rates, which is compared with the traffic congestion pattern observed by Kerner et al. and it is found that the results are consistent with the congestion characteristics in the three-phase traffic flow theory.

  10. Using three-phase theory-based formative research to explore healthy eating in Australian truck drivers.

    Science.gov (United States)

    Vayro, Caitlin; Hamilton, Kyra

    2016-03-01

    In Australia, fruit and vegetable consumption is lower than recommended while discretionary foods (i.e., foods high in fat, sugar, and salt) are eaten in excess. Long-haul truck drivers are a group at risk of unhealthy eating but have received limited attention in the health literature. We aimed to examine long-haul truck drivers eating decisions in order to develop theory-based and empirically-driven health messages to improve their healthy food choices. Drawing on the Theory of Planned Behavior, three-phased formative research was conducted using self-report surveys. Phase 1 (N = 30, Mage = 39.53, SDage = 10.72) identified modal salient beliefs about fruit and vegetable (FV) intake and limiting discretionary choices (DC). There were nine behavioral and seven normative beliefs elicited for both FV and DC; while nine and five control beliefs were elicited for FV and DC, respectively. Phase 2 (N = 148, Mage = 44.23, SDage = 12.08) adopted a prospective design with one week follow-up to examine the predictors of FV and DC intention and behavior. A variety of behavioral and control beliefs were predictive of FV and DC intention and behavior. Normative beliefs were predictive of FV intention and behavior and DC intention only. Phase 3 (N = 20, Mage = 46.9, SDage = 12.85) elicited the reasons why each belief is held/solutions to negative beliefs, that could be used as health messages. In total, 40 reasons/solutions were identified: 26 for FV and 14 for DC. In summary, we found that specific behavioral, normative and control beliefs influenced FV and DC eating decisions. These results have implications for truck driver's health and provide formative research to inform future interventions to improve the food choices of a unique group who are at risk of unhealthy eating behaviors. Copyright © 2015 Elsevier Ltd. All rights reserved.

  11. Analysis of patterns of three-phase bone scintigraphy for patients with complex regional pain syndrome diagnosed using the proposed research criteria (the 'Budapest Criteria').

    Science.gov (United States)

    Moon, J Y; Park, S Y; Kim, Y C; Lee, S C; Nahm, F S; Kim, J H; Kim, H; Oh, S W

    2012-04-01

    Three-phase bone scintigraphy (TPBS) is an established objective diagnostic method for complex regional pain syndrome (CRPS), but its validity remains controversial. The aims of this study were: (i) to re-evaluate the diagnostic performance of TPBS, and (ii) to suggest new TPBS criteria based on the proposed research criteria for CPRS in Budapest (the 2003 Budapest research criteria). The medical records of 228 consecutive patients, evaluated using the Budapest research criteria, were retrospectively analysed. Of these, 116 patients were included in the present study, and 69 of 116 were diagnosed to have CRPS based on these criteria. The diagnostic performance of TPBS was assessed by determining its sensitivity, specificity, and positive and negative likelihood ratios, and new criteria for TPBS were identified by pattern analysis using the Budapest research criteria. The sensitivity, specificity, positive likelihood ratio, and negative likelihood ratio of TPBS for the diagnosis of CRPS according to the Budapest research criteria were 40.0, 76.5, 1.73, and 0.78, respectively. Furthermore, D-D-D, D-D-S, and D-D-I patterns [i.e. according to decreased (D), symmetrical (S), or increased (I) tracer uptake during Phases I, II, and III] of TPBS were found to be positively predictive for CRPS. The diagnostic value of a positive TPBS for CRPS is low from the view point of the Budapest research criteria. Our findings suggest that a diagnosis of CRPS using the Budapest research criteria should be considered when decreased patterns of TPBS are observed during Phases I and II.

  12. Current practices in library/informatics instruction in academic libraries serving medical schools in the Western United States: a three-phase action research study.

    Science.gov (United States)

    Eldredge, Jonathan D; Heskett, Karen M; Henner, Terry; Tan, Josephine P

    2013-09-04

    To conduct a systematic assessment of library and informatics training at accredited Western U.S. medical schools. To provide a structured description of core practices, detect trends through comparisons across institutions, and to identify innovative training approaches at the medical schools. Action research study pursued through three phases. The first phase used inductive analysis on reported library and informatics skills training via publicly-facing websites at accredited medical schools and the academic health sciences libraries serving those medical schools. Phase Two consisted of a survey of the librarians who provide this training to undergraduate medical education students at the Western U.S. medical schools. The survey revealed gaps in forming a complete picture of current practices, thereby generating additional questions that were answered through the Phase Three in-depth interviews. Publicly-facing websites reviewed in Phase One offered uneven information about library and informatics training at Western U.S. medical schools. The Phase Two survey resulted in a 77% response rate. The survey produced a clearer picture of current practices of library and informatics training. The survey also determined the readiness of medical students to pass certain aspects of the United States Medical Licensure Exam. Most librarians interacted with medical school curricular leaders through either curricula committees or through individual contacts. Librarians averaged three (3) interventions for training within the four-year curricula with greatest emphasis upon the first and third years. Library/informatics training was integrated fully into the respective curricula in almost all cases. Most training involved active learning approaches, specifically within Problem-Based Learning or Evidence-Based Medicine contexts. The Phase Three interviews revealed that librarians are engaged with the medical schools' curricular leaders, they are respected for their knowledge and

  13. Three-phase Photovoltaic Systems

    DEFF Research Database (Denmark)

    Kerekes, Tamas; Sera, Dezso; Máthé, Lászlo

    2015-01-01

    , detailing the different photovoltaic inverter structures and topologies as well as discussing the different control layers within a grid-connected photovoltaic plant. Modulation schemes for various photovoltaic inverter topologies, grid synchronization, current control, active and reactive power control......Photovoltaic technology has experienced unprecedented growth in the last two decades, transforming from mainly off-grid niche generation to a major renewable energy technology, reaching approximately 180 GW of capacity worldwide at the end of 2014. Large photovoltaic power plants interfacing...... the grid through a three-phase power electronic converter are now well on the way to becoming a major player in the power system in many countries. Therefore, this article gives an overview of photovoltaic systems with a focus on three-phase applications, presenting these both from a hardware point of view...

  14. Research reactor support

    International Nuclear Information System (INIS)

    2005-01-01

    Research reactors (RRs) have been used in a wide range of applications including nuclear power development, basic physics research, education and training, medical isotope production, geology, industry and other fields. However, many research reactors are fuelled with High Enriched Uranium (HEU), are underutilized and aging, and have significant quantities of spent fuel. HEU inventories (fresh and spent) pose security risks Unavailability of a high-density-reprocessable fuel hinders conversion and limits back-end options and represents a survival dilemma for many RRs. Improvement of interim spent fuel storage is required at some RRs. Many RRs are under-utilized and/or inadequately funded and need to find users for their services, or permanently shut down and eventually decommission. Reluctance to decommission affect both cost and safety (loss of experienced staff ) and many shut down but not decommissioned RR with fresh and/or spent fuel at the sites invoke serious concern. The IAEA's research reactor support helps to ensure that research reactors can be operated efficiently with fuels and targets of lower proliferation and security concern and that operators have appropriate technology and options to manage RR fuel cycle issues, especially on long term interim storage of spent research reactor fuel. Availability of a high-density-reprocessable fuel would expand and improve back end options. The International Atomic Energy Agency provides assistance to Member States to convert research reactors from High Enriched Uranium fuel and targets (for medical isotope production) to qualified Low Enriched Uranium fuel and targets while maintaining reactor performance levels. The assistance includes provision of handbooks and training in the performance of core conversion studies, advice for the procurement of LEU fuel, and expert services for LEU fuel acceptance. The IAEA further provides technical and administrative support for countries considering repatriation of its

  15. Three phase active power filter with selective harmonics elimination

    Directory of Open Access Journals (Sweden)

    Sozański Krzysztof

    2016-03-01

    Full Text Available This paper describes a three phase shunt active power filter with selective harmonics elimination. The control algorithm is based on a digital filter bank. The moving Discrete Fourier Transformation is used as an analysis filter bank. The correctness of the algorithm has been verified by simulation and experimental research. The paper includes exemplary results of current waveforms and their spectra from a three phase active power filter.

  16. Computer supported qualitative research

    CERN Document Server

    Reis, Luís; Sousa, Francislê; Moreira, António; Lamas, David

    2017-01-01

    This book contains an edited selection of the papers accepted for presentation and discussion at the first International Symposium on Qualitative Research (ISQR2016), held in Porto, Portugal, July 12th-14th, 2016. The book and the symposium features the four main application fields Education, Health, Social Sciences and Engineering and Technology and seven main subjects: Rationale and Paradigms of Qualitative Research (theoretical studies, critical reflection about epistemological dimensions, ontological and axiological); Systematization of approaches with Qualitative Studies (literature review, integrating results, aggregation studies, meta -analysis, meta- analysis of qualitative meta- synthesis, meta- ethnography); Qualitative and Mixed Methods Research (emphasis in research processes that build on mixed methodologies but with priority to qualitative approaches); Data Analysis Types (content analysis , discourse analysis , thematic analysis , narrative analysis , etc.); Innovative processes of Qualitative ...

  17. ERC supports antihydrogen research

    CERN Multimedia

    Katarina Anthony

    2013-01-01

    As part of a Europe-wide effort to promote high-level research, the European Research Council (ERC) has awarded a €2.14 million grant to ALPHA spokesperson Jeffrey Hangst, which will further the collaboration’s study of the antihydrogen spectrum. The grant will be used to purchase laser spectroscopy equipment for the new ALPHA-2 set-up.   ALPHA Spokesperson, Jeffrey Hangst, in front of the new ALPHA-2 set-up. The incorporation of lasers into ALPHA-2 will allow the team to take precise measurements of trapped antihydrogen. Among the new equipment financed by the grant will be a high-precision laser and stabilisation system to study the transition from the ground state to the first excited state in antihydrogen. As this spectral line is very well known in hydrogen, its study in antihydrogen will provide essential data for matter/antimatter symmetry investigations. “The grant has come at a perfect time for us,” says Jeffrey Hangst. “We wil...

  18. Environmental insurance: research information support

    OpenAIRE

    Rykova Valentina V.

    2015-01-01

    he article describes information resources to support research on the issue of environmental insurance. It represents a brief analysis of a documentary flow, traces its dynamics and typical-thematic structures, shows the most productive journals

  19. Periodic Operation of Three-Phase Catalytic Reactors

    Czech Academy of Sciences Publication Activity Database

    Silveston, P.T.; Hanika, Jiří

    2005-01-01

    Roč. 82, č. 6 (2005), s. 1105-1142 ISSN 0008-4034 Institutional research plan: CEZ:AV0Z4072921 Keywords : three-phase reactors * trickle bed * periodic operation Subject RIV: CI - Industrial Chemistry, Chemical Engineering Impact factor: 0.574, year: 2005

  20. Three-Phased Wake Vortex Decay

    Science.gov (United States)

    Proctor, Fred H.; Ahmad, Nashat N.; Switzer, George S.; LimonDuparcmeur, Fanny M.

    2010-01-01

    A detailed parametric study is conducted that examines vortex decay within turbulent and stratified atmospheres. The study uses a large eddy simulation model to simulate the out-of-ground effect behavior of wake vortices due to their interaction with atmospheric turbulence and thermal stratification. This paper presents results from a parametric investigation and suggests improvements for existing fast-time wake prediction models. This paper also describes a three-phased decay for wake vortices. The third phase is characterized by a relatively slow rate of circulation decay, and is associated with the ringvortex stage that occurs following vortex linking. The three-phased decay is most prevalent for wakes imbedded within environments having low-turbulence and near-neutral stratification.

  1. Decision Strategy Research: Policy Support

    International Nuclear Information System (INIS)

    Hardeman, F.

    2000-01-01

    The objective of SCK-CEN's R and D programme on decision strategy research are (1) to support and advise the Belgian authorities on specific problems concerning existing and potential hazards from exposure to ionising radiation, both in normal and emergency situations; (2) to perform research on relevant topics that might have an important impact on decision making related to nuclear applications, including social and economic sciences. Main achievements in this area in 1999 are described

  2. Federal support of radiological research

    International Nuclear Information System (INIS)

    Hendee, W.R.

    1981-01-01

    Pervading the plans and objective outlined herein for continued and enhanced federal support of research in radiology is a challenge of unparalleled magnitude, for the economic foundation on which this support is based has rarely been more precarious. The new administration in Washington may well be the most fiscally constrained in half a century, and its stated interest in reducing federal expenditures could have disastrous consequences for the scientific research effort in this country, including that in radiology and the radiological sciences. The circumvention of these consequences may well require the dedicated effort of the entire scientific community over the next few months and years, including that part representing radiology and the radiological sciences

  3. Three phase full wave dc motor decoder

    Science.gov (United States)

    Studer, P. A. (Inventor)

    1977-01-01

    A three phase decoder for dc motors is disclosed which employs an extremely simple six transistor circuit to derive six properly phased output signals for fullwave operation of dc motors. Six decoding transistors are coupled at their base-emitter junctions across a resistor network arranged in a delta configuration. Each point of the delta configuration is coupled to one of three position sensors which sense the rotational position of the motor. A second embodiment of the invention is disclosed in which photo-optical isolators are used in place of the decoding transistors.

  4. The three phases of galaxy formation

    Science.gov (United States)

    Clauwens, Bart; Schaye, Joop; Franx, Marijn; Bower, Richard G.

    2018-05-01

    We investigate the origin of the Hubble sequence by analysing the evolution of the kinematic morphologies of central galaxies in the EAGLE cosmological simulation. By separating each galaxy into disc and spheroidal stellar components and tracing their evolution along the merger tree, we find that the morphology of galaxies follows a common evolutionary trend. We distinguish three phases of galaxy formation. These phases are determined primarily by mass, rather than redshift. For M* ≲ 109.5M⊙ galaxies grow in a disorganised way, resulting in a morphology that is dominated by random stellar motions. This phase is dominated by in-situ star formation, partly triggered by mergers. In the mass range 109.5M⊙ ≲ M* ≲ 1010.5M⊙ galaxies evolve towards a disc-dominated morphology, driven by in-situ star formation. The central spheroid (i.e. the bulge) at z = 0 consists mostly of stars that formed in-situ, yet the formation of the bulge is to a large degree associated with mergers. Finally, at M* ≳ 1010.5M⊙ growth through in-situ star formation slows down considerably and galaxies transform towards a more spheroidal morphology. This transformation is driven more by the buildup of spheroids than by the destruction of discs. Spheroid formation in these galaxies happens mostly by accretion at large radii of stars formed ex-situ (i.e. the halo rather than the bulge).

  5. Research Award: Supporting Inclusive Growth

    International Development Research Centre (IDRC) Digital Library (Canada)

    IDRC CRDI

    The successful candidate will allocate about 50% of the time to his/her own research ... The Research Awardee will also contribute to the management of the ... analysis, and writing skills for different audiences (academic, policy, general public);.

  6. Research Support: The New Mission for Libraries

    Science.gov (United States)

    Mitchell, Erik T.

    2013-01-01

    Research support services are growing areas of importance in academic libraries and are part of the libraries' larger goal to provide wider support for research-related services. Ithaka's "Library Survey 2010" indicated that research support services, along with teaching facilitation, are the two growth areas projected by library directors. In…

  7. Influence of load type on power factor and harmonic composition of three-phase rectifier current

    Science.gov (United States)

    Nikolayzin, N. V.; Vstavskaya, E. V.; Konstantinov, V. I.; Konstantinova, O. V.

    2018-05-01

    This article is devoted to research of the harmonic composition of the three-phase rectifier current consumed when it operates with different types of load. The results are compared with Standard requirements.

  8. Three-Phase Unbalanced Load Flow Tool for Distribution Networks

    DEFF Research Database (Denmark)

    Demirok, Erhan; Kjær, Søren Bækhøj; Sera, Dezso

    2012-01-01

    This work develops a three-phase unbalanced load flow tool tailored for radial distribution networks based on Matlab®. The tool can be used to assess steady-state voltage variations, thermal limits of grid components and power losses in radial MV-LV networks with photovoltaic (PV) generators where...... most of the systems are single phase. New ancillary service such as static reactive power support by PV inverters can be also merged together with the load flow solution tool and thus, the impact of the various reactive power control strategies on the steady-state grid operation can be simply...... investigated. Performance of the load flow solution tool in the sense of resulting bus voltage magnitudes is compared and validated with IEEE 13-bus test feeder....

  9. Government support for hvdc research

    Energy Technology Data Exchange (ETDEWEB)

    1968-07-12

    To help secure a place for Britain in hvdc export market beyond the next decade, the Ministry of Technology is sponsoring. Research into thyristor converters as a replacement for the mercury arc valves now used in terminal equipment. English Electric has secured from Mintech a risk sharing contract contributing nearly 250,000 pounds towards the cost of a development program.

  10. System For Characterizing Three-Phase Brushless dc Motors

    Science.gov (United States)

    Howard, David E.; Smith, Dennis A.

    1996-01-01

    System of electronic hardware and software developed to automate measurements and calculations needed to characterize electromechanical performances of three-phase brushless dc motors, associated shaft-angle sensors needed for commutation, and associated brushless tachometers. System quickly takes measurements on all three phases of motor, tachometer, and shaft-angle sensor simultaneously and processes measurements into performance data. Also useful in development and testing of motors with not only three phases but also two, four, or more phases.

  11. LASL's FY 1978 supporting research program

    International Nuclear Information System (INIS)

    Hammel, E.F.; Merlan, S.J.; Freiwald, D.A.

    1978-09-01

    This report gives a brief overview of Los Alamos Scientific Laboratory's supporting research program, including philosophy, management and program analysis, funding, and a brief description of the kinds of work currently supported. 10 figures

  12. Realization of station for testing asynchronous three-phase motors

    Science.gov (United States)

    Wróbel, A.; Surma, W.

    2016-08-01

    Nowadays, you cannot imagine the construction and operation of machines without the use of electric motors [13-15]. The proposed position is designed to allow testing of asynchronous three-phase motors. The position consists of a tested engine and the engine running as a load, both engines combined with a mechanical clutch [2]. The value of the load is recorded by measuring shaft created with Strain Gauge Bridge. This concept will allow to study the basic parameters of the engines, visualization motor parameters both vector and scalar controlled, during varying load drive system. In addition, registration during the variable physical parameters of the working electric motor, controlled by a frequency converter or controlled by a contactor will be possible. Position is designed as a teaching and research position to characterize the engines. It will be also possible selection of inverter parameters.

  13. Career pathways in research: support and management.

    Science.gov (United States)

    Kenkre, J E; Foxcroft, D R

    This article, the third in the series on career pathways, highlights support and management careers open to nurses working in the NHS and research and development, or people working for funding bodies or charitable organisations. These roles involve ensuring that the right infrastructure is in place to support research projects, and the correct decisions are made about which research projects should be supported and commissioned.

  14. Multitechnology and supporting research programs

    International Nuclear Information System (INIS)

    Anon.

    1978-01-01

    This section includes research efforts that provide information applicable to several presently operating technologies as well as those being investigated for the future. In these technologies the nature of the environmental problem is equally applicable to any one technology; e.g., thermal and chemical pollution of water due to operation of steam electric plants, whether nuclear, fossil fuel, or gas fired; or, the statistical design needed for differentiating a general background of industrial pollution from the contributions, if any, arising from operation of an energy facility. The two main groups of projects reported include biomathematical methods for the analysis of natural systems and the quantitative ecology of impact evaluation; and aquatic ecological studies including the effects of water quality alterations on fish behavior; the ecological effects of combined aquatic stressors; the effects of energy systems effluents on coastal ecosystems; the bioavailability of energy effluent materials in coastal ecosystems; the marine chemistry of energy-generated pollutants; and methods for in situ measurement of pollutants

  15. Efficiency analysis on a two-level three-phase quasi-soft-switching inverter

    DEFF Research Database (Denmark)

    Geng, Pan; Wu, Weimin; Huang, Min

    2013-01-01

    When designing an inverter, an engineer often needs to select and predict the efficiency beforehand. For the standard inverters, plenty of researches are analyzing the power losses and also many software tools are being used for efficiency calculation. In this paper, the efficiency calculation...... for non-conventional inverters with special shoot-through state is introduced and illustrated through the analysis on a special two-level three-phase quasi-soft-switching inverter. Efficiency comparison between the classical two-stage two-level three-phase inverter and the two-level three-phase quasi......-soft-switching inverter is carried out. A 10 kW/380 V prototype is constructed to verify the analysis. The experimental results show that the efficiency of the new inverter is higher than that of the traditional two-stage two- level three-phase inverter....

  16. Retooling Institutional Support Infrastructure for Clinical Research

    Science.gov (United States)

    Snyder, Denise C.; Brouwer, Rebecca N.; Ennis, Cory L.; Spangler, Lindsey L.; Ainsworth, Terry L.; Budinger, Susan; Mullen, Catherine; Hawley, Jeffrey; Uhlenbrauck, Gina; Stacy, Mark

    2016-01-01

    Clinical research activities at academic medical centers are challenging to oversee. Without effective research administration, a continually evolving set of regulatory and institutional requirements can detract investigator and study team attention away from a focus on scientific gain, study conduct, and patient safety. However, even when the need for research administration is recognized, there can be struggles over what form it should take. Central research administration may be viewed negatively, with individual groups preferring to maintain autonomy over processes. Conversely, a proliferation of individualized approaches across an institution can create inefficiencies or invite risk. This article describes experiences establishing a unified research support office at the Duke University School of Medicine based on a framework of customer support. The Duke Office of Clinical Research was formed in 2012 with a vision that research administration at academic medical centers should help clinical investigators navigate the complex research environment and operationalize research ideas. The office provides an array of services that have received high satisfaction ratings. The authors describe the ongoing culture change necessary for success of the unified research support office. Lessons learned from implementation of the Duke Office of Clinical Research may serve as a model for other institutions undergoing a transition to unified research support. PMID:27125563

  17. Research evaluation support services in biomedical libraries

    Directory of Open Access Journals (Sweden)

    Karen Elizabeth Gutzman

    2018-01-01

    Conclusions: Libraries can leverage a variety of evaluation support services as an opportunity to successfully meet an array of challenges confronting the biomedical research community, including robust efforts to report and demonstrate tangible and meaningful outcomes of biomedical research and clinical care. These services represent a transformative direction that can be emulated by other biomedical and research libraries.

  18. Research evaluation support services in biomedical libraries.

    Science.gov (United States)

    Gutzman, Karen Elizabeth; Bales, Michael E; Belter, Christopher W; Chambers, Thane; Chan, Liza; Holmes, Kristi L; Lu, Ya-Ling; Palmer, Lisa A; Reznik-Zellen, Rebecca C; Sarli, Cathy C; Suiter, Amy M; Wheeler, Terrie R

    2018-01-01

    The paper provides a review of current practices related to evaluation support services reported by seven biomedical and research libraries. A group of seven libraries from the United States and Canada described their experiences with establishing evaluation support services at their libraries. A questionnaire was distributed among the libraries to elicit information as to program development, service and staffing models, campus partnerships, training, products such as tools and reports, and resources used for evaluation support services. The libraries also reported interesting projects, lessons learned, and future plans. The seven libraries profiled in this paper report a variety of service models in providing evaluation support services to meet the needs of campus stakeholders. The service models range from research center cores, partnerships with research groups, and library programs with staff dedicated to evaluation support services. A variety of products and services were described such as an automated tool to develop rank-based metrics, consultation on appropriate metrics to use for evaluation, customized publication and citation reports, resource guides, classes and training, and others. Implementing these services has allowed the libraries to expand their roles on campus and to contribute more directly to the research missions of their institutions. Libraries can leverage a variety of evaluation support services as an opportunity to successfully meet an array of challenges confronting the biomedical research community, including robust efforts to report and demonstrate tangible and meaningful outcomes of biomedical research and clinical care. These services represent a transformative direction that can be emulated by other biomedical and research libraries.

  19. A THREE-PHASE BOOST DC-AC CONVERTER

    African Journals Online (AJOL)

    dc-ac converter (inverter) based on the dc-dc boost converters. ... Sliding mode controllers are designed to perform a robust control for the ... Computer simulations and spectral analysis demon- ... the conventional three-phase buck inverter,.

  20. Research on Parallel Three Phase PWM Converters base on RTDS

    Science.gov (United States)

    Xia, Yan; Zou, Jianxiao; Li, Kai; Liu, Jingbo; Tian, Jun

    2018-01-01

    Converters parallel operation can increase capacity of the system, but it may lead to potential zero-sequence circulating current, so the control of circulating current was an important goal in the design of parallel inverters. In this paper, the Real Time Digital Simulator (RTDS) is used to model the converters parallel system in real time and study the circulating current restraining. The equivalent model of two parallel converters and zero-sequence circulating current(ZSCC) were established and analyzed, then a strategy using variable zero vector control was proposed to suppress the circulating current. For two parallel modular converters, hardware-in-the-loop(HIL) study based on RTDS and practical experiment were implemented, results prove that the proposed control strategy is feasible and effective.

  1. Financial support for agricultural research in Alberta

    International Nuclear Information System (INIS)

    Teklemariam, Y.; Martin, J.

    1992-01-01

    A summary of the objectives and operational guidelines of 'Farming for the future', Alberta Agriculture's main research funding program, is provided, with emphasis on aspects relevant to research on the effects of acid-forming emissions on livestock. The program has two main objectives: to improve farm income, and to increase the long-term viability of agriculture in Alberta. The Research Program funds agricultural research conducted by research scientists and the On-farm Demonstration Program supports testing and demonstration studies conducted by producers on their farms. The procedures for applying for funds, criteria for evaluation, and funding available for acid-forming emission research are discussed. 1 fig

  2. A Fuzzy Logic Based Three phase Inverter with Single DC Source for Grid Connected PV System Employing Three Phase Transformer

    OpenAIRE

    Mani, venkatesan; Ramachandran, Rajeswari; N, Deverajan

    2016-01-01

    A fuzzy based three phase inverter with single DC source for grid connected photo voltaic (PV) system employing three phase transformer is presented in this paper. Space Vector Pulse Width Modulation (SVPWM) control scheme is effectively used to generate the appropriate switching sequences to the inverter switches. The intend of the fuzzy logic approach is to meet high quality output, fast response and high robustness. Finally Total Harmonics Distortion (THD) generated by the inverter is comp...

  3. Energy Demodulation Algorithm for Flow Velocity Measurement of Oil-Gas-Water Three-Phase Flow

    Directory of Open Access Journals (Sweden)

    Yingwei Li

    2014-01-01

    Full Text Available Flow velocity measurement was an important research of oil-gas-water three-phase flow parameter measurements. In order to satisfy the increasing demands for flow detection technology, the paper presented a gas-liquid phase flow velocity measurement method which was based on energy demodulation algorithm combing with time delay estimation technology. First, a gas-liquid phase separation method of oil-gas-water three-phase flow based on energy demodulation algorithm and blind signal separation technology was proposed. The separation of oil-gas-water three-phase signals which were sampled by conductance sensor performed well, so the gas-phase signal and the liquid-phase signal were obtained. Second, we used the time delay estimation technology to get the delay time of gas-phase signals and liquid-phase signals, respectively, and the gas-phase velocity and the liquid-phase velocity were derived. At last, the experiment was performed at oil-gas-water three-phase flow loop, and the results indicated that the measurement errors met the need of velocity measurement. So it provided a feasible method for gas-liquid phase velocity measurement of the oil-gas-water three-phase flow.

  4. Quality research in healthcare: are researchers getting enough statistical support?

    Directory of Open Access Journals (Sweden)

    Ambler Gareth

    2006-01-01

    Full Text Available Abstract Background Reviews of peer-reviewed health studies have highlighted problems with their methodological quality. As published health studies form the basis of many clinical decisions including evaluation and provisions of health services, this has scientific and ethical implications. The lack of involvement of methodologists (defined as statisticians or quantitative epidemiologists has been suggested as one key reason for this problem and this has been linked to the lack of access to methodologists. This issue was highlighted several years ago and it was suggested that more investments were needed from health care organisations and Universities to alleviate this problem. Methods To assess the current level of methodological support available for health researchers in England, we surveyed the 25 National Health Services Trusts in England, that are the major recipients of the Department of Health's research and development (R&D support funding. Results and discussion The survey shows that the earmarking of resources to provide appropriate methodological support to health researchers in these organisations is not widespread. Neither the level of R&D support funding received nor the volume of research undertaken by these organisations showed any association with the amount they spent in providing a central resource for methodological support for their researchers. Conclusion The promotion and delivery of high quality health research requires that organisations hosting health research and their academic partners put in place funding and systems to provide appropriate methodological support to ensure valid research findings. If resources are limited, health researchers may have to rely on short courses and/or a limited number of advisory sessions which may not always produce satisfactory results.

  5. Library Research Support in Queensland: A Survey

    Science.gov (United States)

    Richardson, Joanna; Nolan-Brown, Therese; Loria, Pat; Bradbury, Stephanie

    2012-01-01

    University libraries worldwide are reconceptualising the ways in which they support the research agenda in their respective institutions. This paper is based on a survey completed by member libraries of the Queensland University Libraries Office of Cooperation (QULOC), the findings of which may be informative for other university libraries. After…

  6. Database Support for Research in Public Administration

    Science.gov (United States)

    Tucker, James Cory

    2005-01-01

    This study examines the extent to which databases support student and faculty research in the area of public administration. A list of journals in public administration, public policy, political science, public budgeting and finance, and other related areas was compared to the journal content list of six business databases. These databases…

  7. Calls for Canada to support basic research

    Science.gov (United States)

    Gwynne, Peter

    2017-08-01

    Canada’s decade-long shift of financial support from fundamental studies towards applied research is dismantling the nation’s funding of basic science, according to a report by the Global Young Academy (GYA) - an international society of young scientists.

  8. Using Network Science to Support Design Research

    DEFF Research Database (Denmark)

    Parraguez Ruiz, Pedro; Maier, Anja

    2016-01-01

    and societal impact. This chapter contributes to the use of network science in empirical studies of design organisations. It focuses on introducing a network-based perspective on the design process and in particular on making use of network science to support design research and practice. The main contribution...... of this chapter is an overview of the methodological challenges and core decision points when embarking on network-based design research, namely defining the overall research purpose and selecting network features. We furthermore highlight the potential for using archival data, the opportunities for navigating...

  9. Three-phase electric drive with modified electronic smoothing inductor

    DEFF Research Database (Denmark)

    Singh, Yash Veer; Rasmussen, Peter Omand; Andersen, Torben Ole

    2010-01-01

    This paper presents a three-phase electric drive with a modified electronic smoothing inductor (MESI) having reduced size of passive components. The classical electronic smoothing inductor (ESI) is able to control a diode bridge output current and also reduce not only mains current harmonics...

  10. Sine-wave three phase resonance inverter for operation of ...

    African Journals Online (AJOL)

    This paper proposes a high performance single-stage three phase inverter topology for the autonomous operation of renewable energy systems. The proposed configuration can boost the low voltage of renewable energy systems such as photo voltaic systems, fuel cells, and etc can also convert the output dc power, into ...

  11. Three-Phase Flow and Capillarity in Porous Media

    Energy Technology Data Exchange (ETDEWEB)

    Helset, H.M.

    1996-06-01

    Multiphase flow occurs in most production operations on the reservoir rock of an oil field. Three-phase flow occurs in many oil recovery processes, such as gas or water alternating gas injection into water flooded reservoirs, thermal oil recovery and surfactant flooding. In this doctoral thesis, three-phase flow in porous media is modeled using the method of characteristics and simple wave theory. The general mathematical methods are used to model different flow processes: secondary migration of hydrocarbons, gravity segregated three-phase flow, and displacement experiments for relative permeabilities. The main conclusions from applying the methods to the migration process through a water-saturated carrier bed to a partially permeable seal are: (1) the three-phase solutions are generally dominated by the very low gas viscosity and gas density, (2) countercurrent flow and interference between the gas and oil mobilities can lead to trapping in situations where the permeability contrast between the seal and the carrier bed is insufficient to trap oil alone, (3) zones in which pressures exceed those from hydrostatic gradients (overpressured zones) exist even when the permeability contrast between the seal and the carrier bed is modest. The discussion of gravity segregated flow identifies stable displacement fronts, which usually occur only for a single value of the gas-water injection ratio. The new method developed for interpreting displacement experiments, with capillary pressure included, is based on the travelling wave solution of the flow equations. 185 refs., 69 figs., 5 tabs.

  12. Controlling An Inverter-Driven Three-Phase Motor

    Science.gov (United States)

    Dolland, C.

    1984-01-01

    Control system for three-phase permanent-magnet motor driven by linecommutated inverter uses signals generated by integrating back emf of each phase of motor. High-pass filter network eliminates low-frequency components from control loop while maintaining desired power factor.

  13. A cascaded three-phase symmetrical multistage voltage multiplier

    International Nuclear Information System (INIS)

    Iqbal, Shahid; Singh, G K; Besar, R; Muhammad, G

    2006-01-01

    A cascaded three-phase symmetrical multistage Cockcroft-Walton voltage multiplier (CW-VM) is proposed in this report. It consists of three single-phase symmetrical voltage multipliers, which are connected in series at their smoothing columns like string of batteries and are driven by three-phase ac power source. The smoothing column of each voltage multiplier is charged twice every cycle independently by respective oscillating columns and discharged in series through load. The charging discharging process completes six times a cycle and therefore the output voltage ripple's frequency is of sixth order of the drive signal frequency. Thus the proposed approach eliminates the first five harmonic components of load generated voltage ripples and sixth harmonic is the major ripple component. The proposed cascaded three-phase symmetrical voltage multiplier has less than half the voltage ripple, and three times larger output voltage and output power than the conventional single-phase symmetrical CW-VM. Experimental and simulation results of the laboratory prototype are given to show the feasibility of proposed cascaded three-phase symmetrical CW-VM

  14. Three phase voltage measurements with simple open air sensors

    NARCIS (Netherlands)

    Heesch, van E.J.M.; Caspers, R.; Gulickx, P.F.M.; Jacobs, G.A.P.; Kersten, W.F.J.; Laan, van der P.C.T.

    1991-01-01

    A low cost, easy to install high-voltage measuring system is described for open air substations and overhead lines. Based on the Differentiating/Integrating (D/I) principle, three free-standing capacitive pickup electrodes are used to sense the three phase to ground voltages. Apart from the

  15. Imaging phase holdup distribution of three phase flow systems using dual source gamma ray tomography

    International Nuclear Information System (INIS)

    Varma, Rajneesh; Al-Dahhan, Muthanna; O'Sullivan, Joseph

    2008-01-01

    Full text: Multiphase reaction and process systems are used in abundance in the chemical and biochemical industry. Tomography has been successfully employed to visualize the hydrodynamics of multiphase systems. Most of the tomography methods (gamma ray, x-ray and electrical capacitance and resistance) have been successfully implemented for two phase dynamic systems. However, a significant number of chemical and biochemical systems consists of dynamic three phases. Research effort directed towards the development of tomography techniques to image such dynamic system has met with partial successes for specific systems with applicability to limited operating conditions. A dual source tomography scanner has been developed that uses the 661 keV and 1332 keV photo peaks from the 137 Cs and 60 Co for imaging three phase systems. A new approach has been developed and applied that uses the polyenergetic Alternating Minimization (A-M) algorithm, developed by O'Sullivan and Benac (2007), for imaging the holdup distribution in three phases' dynamic systems. The new approach avoids the traditional post image processing approach used to determine the holdup distribution where the attenuation images of the mixed flow obtained from gamma ray photons of two different energies are used to determine the holdup of three phases. In this approach the holdup images are directly reconstructed from the gamma ray transmission data. The dual source gamma ray tomography scanner and the algorithm were validated using a three phase phantom. Based in the validation, three phase holdup studies we carried out in slurry bubble column containing gas liquid and solid phases in a dynamic state using the dual energy gamma ray tomography. The key results of the holdup distribution studies in the slurry bubble column along with the validation of the dual source gamma ray tomography system would be presented and discussed

  16. Semantic Support for Complex Ecosystem Research Environments

    Science.gov (United States)

    Klawonn, M.; McGuinness, D. L.; Pinheiro, P.; Santos, H. O.; Chastain, K.

    2015-12-01

    As ecosystems come under increasing stresses from diverse sources, there is growing interest in research efforts aimed at monitoring, modeling, and improving understanding of ecosystems and protection options. We aimed to provide a semantic infrastructure capable of representing data initially related to one large aquatic ecosystem research effort - the Jefferson project at Lake George. This effort includes significant historical observational data, extensive sensor-based monitoring data, experimental data, as well as model and simulation data covering topics including lake circulation, watershed runoff, lake biome food webs, etc. The initial measurement representation has been centered on monitoring data and related provenance. We developed a human-aware sensor network ontology (HASNetO) that leverages existing ontologies (PROV-O, OBOE, VSTO*) in support of measurement annotations. We explicitly support the human-aware aspects of human sensor deployment and collection activity to help capture key provenance that often is lacking. Our foundational ontology has since been generalized into a family of ontologies and used to create our human-aware data collection infrastructure that now supports the integration of measurement data along with simulation data. Interestingly, we have also utilized the same infrastructure to work with partners who have some more specific needs for specifying the environmental conditions where measurements occur, for example, knowing that an air temperature is not an external air temperature, but of the air temperature when windows are shut and curtains are open. We have also leveraged the same infrastructure to work with partners more interested in modeling smart cities with data feeds more related to people, mobility, environment, and living. We will introduce our human-aware data collection infrastructure, and demonstrate how it uses HASNetO and its supporting SOLR-based search platform to support data integration and semantic browsing

  17. Management of Research Organization: Informational Support

    Directory of Open Access Journals (Sweden)

    Natalia Bruc

    2011-10-01

    Full Text Available We consider the conceptual approach to the system, providing scientific management of a research institution, and information support of scientific cooperation with similar institutions from other countries. This approach is partly tested at the Institute of Mathematics and Computer Science of Academy of Sciences of Moldova and is proposed for several other academic institutions. We believe that this approach will allow automated information management of cooperation with foreign scientific institutions.

  18. Engaging community to support HIV prevention research.

    Science.gov (United States)

    Sahay, Seema; Mehendale, Sanjay

    2011-01-01

    Actively engaging communities in effective partnerships is considered critical for ethically robust and locally relevant HIV prevention research. This can be challenging in developing countries that have little prior experience in this area. This paper summarizes processes and lessons learnt while setting up the Community Involvement Plan of National AIDS Research Institute, Pune, India. Formal partnerships were established with voluntary agencies. The focus was on using strategies adapted from participatory learning and action techniques. The community program was implemented through peer educators specifically identified from the communities where partner non-governmental organizations function. At the grass root level, peer educators imparted education to the common people about research studies and helped to implement community based recruitment and retention activities. The focus was on facilitating periodic interaction between the outreach workers of the research team and the peers and modifying the strategies till they were found locally implementable and appropriate. Through adequate time investment, mutually beneficial and respectful partnerships with community based organizations and grass root level workers, the community became actively involved in clinical research. The program helped in developing a sense of partnership among the peers for the research conducted by the research organization, widening the net of community education and identification of research participants. By building trust in the community and implementing research within an ethical framework, culturally sensitive matters were appropriately addressed. The community involvement process is long, laborious and ever-evolving. Effective community engagement requires institutional leadership support, adequate funding and commitment by researchers. It is possible to sustain such a model in a resource limited setting.

  19. Lattice Boltzmann model for three-phase viscoelastic fluid flow

    Science.gov (United States)

    Xie, Chiyu; Lei, Wenhai; Wang, Moran

    2018-02-01

    A lattice Boltzmann (LB) framework is developed for simulation of three-phase viscoelastic fluid flows in complex geometries. This model is based on a Rothman-Keller type model for immiscible multiphase flows which ensures mass conservation of each component in porous media even for a high density ratio. To account for the viscoelastic effects, the Maxwell constitutive relation is correctly introduced into the momentum equation, which leads to a modified lattice Boltzmann evolution equation for Maxwell fluids by removing the normal but excess viscous term. Our simulation tests indicate that this excess viscous term may induce significant errors. After three benchmark cases, the displacement processes of oil by dispersed polymer are studied as a typical example of three-phase viscoelastic fluid flow. The results show that increasing either the polymer intrinsic viscosity or the elastic modulus will enhance the oil recovery.

  20. Losses in armoured three-phase submarine cables

    DEFF Research Database (Denmark)

    Ebdrup, Thomas; Silva, Filipe Miguel Faria da; Bak, Claus Leth

    2014-01-01

    The number of offshore wind farms will keep increasing in the future as a part of the shift towards a CO2 free energy production. The energy harvested from the wind farm must be brought to shore, which is often done by using a three-phase armoured submarine power cable. The use of an armour...... increases the losses in armoured cables compared to unarmoured cables. In this paper a thorough state of the art analysis is conducted on armour losses in three-phase armoured submarine power cables. The analysis shows that the IEC 60287-1-1 standard overestimates the armour losses which lead...... to the installation of cables with excessive phase conductor cross section. This paper also presents an example of the potential economic benefits of having a better knowledge of the losses introduced by the armour....

  1. Three phase load flow; Fluxo de carga trifasico

    Energy Technology Data Exchange (ETDEWEB)

    Zago, Maria Goretti

    1992-12-01

    The phase model which is used in the analysis and planning of electric power system is based on the hypothesis that both the transmission system and load are equilibrated. Such a system, which presents the advantage of being simple,presents satisfactory results in several cases, however, for certain applications this system is inadequate. this work presents an alternative method based on three-phase load flow which an be applied to electric power distribution networks 19 refs., 25 figs., 24 tabs.

  2. Three-phase Resonant DC-link Converter

    OpenAIRE

    Munk-Nielsen, Stig

    1997-01-01

    The purpose of the project is to develop a three-phase resonant converter suitable for standard speed drives. The motivation for working with resonant converters is found in the problem of the standard converter type used today. In standard converter type Pulse Width Modulated-Voltage Source Inverter, PWM-VSI, the switches are subject to high current and voltage stress during switching, which causes losses. The fast switching of modern switches reduces switching losses. Unfortunately this pro...

  3. Three-Phase Harmonic Analysis Method for Unbalanced Distribution Systems

    Directory of Open Access Journals (Sweden)

    Jen-Hao Teng

    2014-01-01

    Full Text Available Due to the unbalanced features of distribution systems, a three-phase harmonic analysis method is essential to accurately analyze the harmonic impact on distribution systems. Moreover, harmonic analysis is the basic tool for harmonic filter design and harmonic resonance mitigation; therefore, the computational performance should also be efficient. An accurate and efficient three-phase harmonic analysis method for unbalanced distribution systems is proposed in this paper. The variations of bus voltages, bus current injections and branch currents affected by harmonic current injections can be analyzed by two relationship matrices developed from the topological characteristics of distribution systems. Some useful formulas are then derived to solve the three-phase harmonic propagation problem. After the harmonic propagation for each harmonic order is calculated, the total harmonic distortion (THD for bus voltages can be calculated accordingly. The proposed method has better computational performance, since the time-consuming full admittance matrix inverse employed by the commonly-used harmonic analysis methods is not necessary in the solution procedure. In addition, the proposed method can provide novel viewpoints in calculating the branch currents and bus voltages under harmonic pollution which are vital for harmonic filter design. Test results demonstrate the effectiveness and efficiency of the proposed method.

  4. Precise derating of three phase induction motors with unbalanced voltages

    International Nuclear Information System (INIS)

    Faiz, Jawad; Ebrahimpour, H.

    2007-01-01

    Performance analysis of three phase induction motors under supply voltage unbalance conditions is normally conducted using the well-known symmetrical components analysis. In this analysis, the voltage unbalance level at the terminals of the machine is assessed by means of the NEMA or IEC definitions. Both definitions lead to a relatively large error in predicting the performance of a machine. A method has recently been proposed in which, in addition to the voltage unbalance factor (VUF), the phase angle has been taken into account in the analysis. This means that the voltage unbalance factor is regarded as a complex value. This paper shows that although the use of the complex VUF reduces the computational error considerably, it is still high. This is proven by evaluating the derating factor of a three phase induction motor. A method is introduced to determine the derating factor precisely using the complex unbalance factor for an induction motor operating under any unbalanced supply condition. A practical case for derating of a typical three phase squirrel cage induction motor supplied by an unbalanced voltage is studied in the paper

  5. Community-oriented support and research structures

    Energy Technology Data Exchange (ETDEWEB)

    Attig, Norbert; Eickermann, Thomas; Gibbon, Paul; Lippert, Thomas, E-mail: th.lippert@fz-juelich.d [Institute for Advanced Simulation, Juelich Supercomputing Centre, Forschungszentrum Juelich, 52425 Juelich (Germany)

    2009-07-01

    Coordinated by the Partnership for Advanced Computing in Europe (PRACE) Europe is restructuring and strengthening its high-performance computing infrastructure with the aim to create a model HPC ecosystem. At the tip of the pyramid, up to six centres are envisaged that will operate systems of the highest performance class. The HPC Research Infrastructure (HPC-RI) will comprise European, national and regional centres. Science communities are integral partners, strong links will include Grid and Cloud users. The HPC-RI strives at providing scientists all over Europe, on the one hand, with unlimited and independent access to state-of-the-art computer resources in all performance classes and, on the other hand, with a world-class pan-European competence and support network. While the hardware-oriented buildup of the infrastructure is making progress, high-quality user support and software development in the upcoming era of unprecedented parallelism and exascale on the horizon have become the imminent challenges. This has been clearly recognized by the European Commission, who will issue calls for proposals to fund petascale software development in summer 2009. Although traditional support structures are well established in Europe's major supercomputing centres, it is questionable if these structures are able to meet the challenges of the future: in general, support structures are based on cross-disciplinary computer science and mathematics teams; disciplinary computational science support usually is given in an ad-hoc, project-oriented manner. In this paper, we describe our approach to establish a suitable support structure-Simulation Laboratories (SL). SLs are currently being established at the Juelich Supercomputing Centre of the Forschungszentrum Juelich (FZJ) and at the Steinbuch Centre for Computing (SCC) of the Karlsruhe Institute for Technology (KIT) in Germany. While SLs are community-oriented, i.e. each SL focusses on a specific community, they are

  6. Community-oriented support and research structures

    International Nuclear Information System (INIS)

    Attig, Norbert; Eickermann, Thomas; Gibbon, Paul; Lippert, Thomas

    2009-01-01

    Coordinated by the Partnership for Advanced Computing in Europe (PRACE) Europe is restructuring and strengthening its high-performance computing infrastructure with the aim to create a model HPC ecosystem. At the tip of the pyramid, up to six centres are envisaged that will operate systems of the highest performance class. The HPC Research Infrastructure (HPC-RI) will comprise European, national and regional centres. Science communities are integral partners, strong links will include Grid and Cloud users. The HPC-RI strives at providing scientists all over Europe, on the one hand, with unlimited and independent access to state-of-the-art computer resources in all performance classes and, on the other hand, with a world-class pan-European competence and support network. While the hardware-oriented buildup of the infrastructure is making progress, high-quality user support and software development in the upcoming era of unprecedented parallelism and exascale on the horizon have become the imminent challenges. This has been clearly recognized by the European Commission, who will issue calls for proposals to fund petascale software development in summer 2009. Although traditional support structures are well established in Europe's major supercomputing centres, it is questionable if these structures are able to meet the challenges of the future: in general, support structures are based on cross-disciplinary computer science and mathematics teams; disciplinary computational science support usually is given in an ad-hoc, project-oriented manner. In this paper, we describe our approach to establish a suitable support structure-Simulation Laboratories (SL). SLs are currently being established at the Juelich Supercomputing Centre of the Forschungszentrum Juelich (FZJ) and at the Steinbuch Centre for Computing (SCC) of the Karlsruhe Institute for Technology (KIT) in Germany. While SLs are community-oriented, i.e. each SL focusses on a specific community, they are structured

  7. A DSP controlled one-to-three phase matrix converter

    Energy Technology Data Exchange (ETDEWEB)

    Dubovsky, J.; Dobrucly, B; Tabacek, R.; Havrila, R. [Department of Electric Traction and Energetics Faculty of Electrical Engineering, University of Zilina (Slovakia)

    1997-12-31

    This paper deals with the theoretical analysis computer simulation and experimental results of IM fed by a one-to-three phase matrix converter which offers a unique solution for single phase electric traction applications. The proposed drive in comparison with currently used conventional drives reduces the number of power switching elements of the converter, which increases drives dependability and brings lower investment in power electronics used in drive. Further advantage is that the converter is controlled with nearly unity power factor which cuts down the operational expenses and offers higher overall performance of the drive. (orig.) 6 refs.

  8. LH2 three-phase pump control circuit description

    International Nuclear Information System (INIS)

    Pierce, W.

    1977-05-01

    A brief description and circuit drawings are given for a pump control system. The pump is used to circulate liquid hydrogen through the cell and heat exchanger of an LH 2 target. The pump is powered by three-phase 60 cycle power, and the control unit is powered from a positive and negative 24 V dc supply available in the NIM Bin. The control unit is packaged in a double-width NIM module. Drawings are given for the pump speed indicator, function generator, and power supply

  9. LCCT-derived three-level three-phase inverters

    DEFF Research Database (Denmark)

    Shults, Tatiana; Husev, Oleksandr; Blaabjerg, Frede

    2017-01-01

    Solutions for a family of the novel three-level neutral-point-clamped (NPC) inductor-capacitor-capacitor-transformer (LCCT)-derived three-phase inverters are described and compared. Component design guidelines and steady state analysis, current and voltage waveforms are given. The authors......' simulation results confirm the theoretical predictions. It was found that an asymmetrical three-level NPC LCCT-derived inverter with a single diode in the impedance source network is the most promising solution. Experimental results for an asymmetrical three-level NPC LCCT-derived inverter with a single...

  10. Three-phase Resonant DC-link Converter

    DEFF Research Database (Denmark)

    Munk-Nielsen, Stig

    The purpose of the project is to develop a three-phase resonant converter suitable for standard speed drives. The motivation for working with resonant converters is found in the problem of the standard converter type used today. In standard converter type Pulse Width Modulated-Voltage Source...... Inverter, PWM-VSI, the switches are subject to high current and voltage stress during switching, which causes losses. The fast switching of modern switches reduces switching losses. Unfortunately this procedure increased dv/dt and the size of the input/output filters of the PWM-SVI must be increased...

  11. Collaboratory for support of scientific research

    International Nuclear Information System (INIS)

    Casper, T.A.; Meyer, W.H.; Moller, J.M.

    1998-01-01

    Collaboration is an increasingly important aspect of magnetic fusion energy research. With the increased size and cost of experiments needed to approach reactor conditions, the numbers being constructed has become limited. In order to satisfy the desire for many groups to conduct research on these facilities, we have come to rely more heavily on collaborations. Fortunately, at the same time, development of high performance computers and fast and reliable wide area networks has provided technological solutions necessary to support the increasingly distributed work force without the need for relocation of entire research staffs. Development of collaboratories, collaborative or virtual laboratories, is intended to provide the capability needed to interact from afar with colleagues at multiple sites. These technologies are useful to groups interacting remotely during experimental operations as well as to those involved in the development of analysis codes and large scale simulations The term ''collaboratory'' refers to a center without walls in which researchers can perform their studies without regard to geographical location - interacting with colleagues, accessing instrumentation, sharing data and computational resources, and accessing information from digital libraries [1],[2]. While it is widely recognized that remote collaboration is not a universal replacement for personal contact, it does afford a means for extending that contact in a manner that minimizes the need for relocation and for travel while more efficiently utilizmg resources and staff that are geographically distant from the central facility location, be it an experiment or design center While the idea of providing a remote environment that is ''as good as being there'' is admirable, it is also important to recognize and capitalize on any differences unique to being remote [3] Magnetic fusion energy research is not unique in its increased dependence on and need to improve methods for collaborative

  12. The Use of the Internet to Support General Aviation Research

    Science.gov (United States)

    Rowbottom, James H.

    1995-01-01

    For the past few years, innovation in the field of General Aviation (GA) has declined. The reason for this decline has not been because of a lack of ideas, but rather a lack of funds necessary to convert these ideas into reality. NASA implemented the Small Business Innovative Research (SBIR) program in an effort to promote new technology in General Aviation. Under this program, small business with good ideas present them to NASA who reviews them and determines their value potential in the GA market. If the company's idea proves worthy, NASA subsidizes their research in three phases that include the research, testing, development, and production of their product. The purpose of my internship this summer was to use the Internet to promote the work of SBIR companies globally to prospective investors.

  13. A fuzzy controlled three-phase centrifuge for waste separation

    International Nuclear Information System (INIS)

    Parkinson, W.J.; Smith, R.E.; Miller, N.

    1998-02-01

    The three-phase centrifuge technology discussed in this paper was developed by Neal Miller, president of Centech, Inc. The three-phase centrifuge is an excellent device for cleaning up oil field and refinery wastes which are typically composed of hydrocarbons, water, and solids. The technology is unique. It turns the waste into salable oil, reusable water, and landfill-able solids. No secondary waste is produced. The problem is that only the inventor can set up and run the equipment well enough to provide an optimal cleanup. Demand for this device has far exceeded a one man operation. There is now a need for several centrifuges to be operated at different locations at the same time. This has produced a demand for an intelligent control system, one that could replace a highly skilled operator, or at least supplement the skills of a less experienced operator. The control problem is ideally suited to fuzzy logic, since the centrifuge is a highly complicated machine operated entirely by the skill and experience of the operator. A fuzzy control system was designed for and used with the centrifuge

  14. Three-phase scintigraphy in the Sudeck syndrome

    International Nuclear Information System (INIS)

    Koppers, B.

    1982-01-01

    37 patients with clinically and radiologically proved reflex sympathetic dystrophy syndrome were scintigraphied by sup(99)mTc-MDP (three-phase scintigraphy). In 87% of the examinations (all three-phases) an increased tracer accumulation in the region of the affected limb could be seen scintigraphically. The majority of the positive results (92% resp. 87%) were found in the intervall phase (phase II) and the late phase (phase III) of the scintigraphic examinations. - We recommend a staging of the increase of the tracer accumulation when examing the reflex sympathetic dystrophy syndrome. This staging doesn't significantly correlate with the familiar clinical and radiological stagings. However it may be useful when assessing the course of the syndrome. - Increased tracer accumulations could be observed in the case of clinically, radiologically and scintigraphically manifest reflex sympathetic dystrophy syndrome in the region of the foot, frequently in the ipsilateral knee region, rarely in the ipsilateral hip joint region, although clinically the syndrome could not be observed in these regions. (orig.) [de

  15. Infrastructure to Support Hydrologic Research: Information Systems

    Science.gov (United States)

    Lall, U.; Duffy, C j

    2001-12-01

    Hydrologic Sciences are inherently interdisciplinary. Consequently, a myriad state variables are of interest to hydrologists. Hydrologic processes transcend many spatial and temporal scales, and their measurements reflect a variety of scales of support. The global water cycle is continuously modified by human activity through changes in land use, alteration of rivers, irrigation and groundwater pumping and through a modification of atmospheric composition. Since water is a solvent and a medium of transport, the water cycle fundamentally influences other material and energy cycles. This metaphor extends to the function that a hydrologic research information system needs to provide, to facilitate discovery in earth systems science, and to improve our capability to manage resources and hazards in a sustainable manner. At present, we have a variety of sources that provide data useful for hydrologic analyses, that range from massive remote sensed data sets, to sparsely sampled historical and paleo data. Consequently, the first objective of the Hydrologic Information Systems (HIS) group is to design a data services system that makes these data accessible in a uniform and useful way for specific, prioritized research goals. The design will include protocols for archiving and disseminating data from the Long Term Hydrologic Observatories (LTHOs), and comprehensive modeling experiments. Hydrology has a rich tradition of mathematical and statistical modeling of processes. However, given limited data and access to it, and a narrow focus that has not exploited connections to climatic and ecologic processes (among others), there have been only a few forays into diagnostic analyses of hydrologic fields, to identify and evaluate spatial and process teleconnections and an appropriate reduced space for modeling and understanding systems. The HIS initiative consequently proposes an investment in research and the provision of toolboxes to facilitate such analyses using the data

  16. Clinical Research Informatics: Supporting the Research Study Lifecycle.

    Science.gov (United States)

    Johnson, S B

    2017-08-01

    Objectives: The primary goal of this review is to summarize significant developments in the field of Clinical Research Informatics (CRI) over the years 2015-2016. The secondary goal is to contribute to a deeper understanding of CRI as a field, through the development of a strategy for searching and classifying CRI publications. Methods: A search strategy was developed to query the PubMed database, using medical subject headings to both select and exclude articles, and filtering publications by date and other characteristics. A manual review classified publications using stages in the "research study lifecycle", with key stages that include study definition, participant enrollment, data management, data analysis, and results dissemination. Results: The search strategy generated 510 publications. The manual classification identified 125 publications as relevant to CRI, which were classified into seven different stages of the research lifecycle, and one additional class that pertained to multiple stages, referring to general infrastructure or standards. Important cross-cutting themes included new applications of electronic media (Internet, social media, mobile devices), standardization of data and procedures, and increased automation through the use of data mining and big data methods. Conclusions: The review revealed increased interest and support for CRI in large-scale projects across institutions, regionally, nationally, and internationally. A search strategy based on medical subject headings can find many relevant papers, but a large number of non-relevant papers need to be detected using text words which pertain to closely related fields such as computational statistics and clinical informatics. The research lifecycle was useful as a classification scheme by highlighting the relevance to the users of clinical research informatics solutions. Georg Thieme Verlag KG Stuttgart.

  17. Advanced computational model for three-phase slurry reactors

    International Nuclear Information System (INIS)

    Goodarz Ahmadi

    2001-10-01

    In the second year of the project, the Eulerian-Lagrangian formulation for analyzing three-phase slurry flows in a bubble column is further developed. The approach uses an Eulerian analysis of liquid flows in the bubble column, and makes use of the Lagrangian trajectory analysis for the bubbles and particle motions. An experimental set for studying a two-dimensional bubble column is also developed. The operation of the bubble column is being tested and diagnostic methodology for quantitative measurements is being developed. An Eulerian computational model for the flow condition in the two-dimensional bubble column is also being developed. The liquid and bubble motions are being analyzed and the results are being compared with the experimental setup. Solid-fluid mixture flows in ducts and passages at different angle of orientations were analyzed. The model predictions were compared with the experimental data and good agreement was found. Gravity chute flows of solid-liquid mixtures is also being studied. Further progress was also made in developing a thermodynamically consistent model for multiphase slurry flows with and without chemical reaction in a state of turbulent motion. The balance laws are obtained and the constitutive laws are being developed. Progress was also made in measuring concentration and velocity of particles of different sizes near a wall in a duct flow. The technique of Phase-Doppler anemometry was used in these studies. The general objective of this project is to provide the needed fundamental understanding of three-phase slurry reactors in Fischer-Tropsch (F-T) liquid fuel synthesis. The other main goal is to develop a computational capability for predicting the transport and processing of three-phase coal slurries. The specific objectives are: (1) To develop a thermodynamically consistent rate-dependent anisotropic model for multiphase slurry flows with and without chemical reaction for application to coal liquefaction. Also establish the

  18. Advanced computational model for three-phase slurry reactors

    International Nuclear Information System (INIS)

    Goodarz Ahmadi

    2000-11-01

    In the first year of the project, solid-fluid mixture flows in ducts and passages at different angle of orientations were analyzed. The model predictions are compared with the experimental data and good agreement was found. Progress was also made in analyzing the gravity chute flows of solid-liquid mixtures. An Eulerian-Lagrangian formulation for analyzing three-phase slurry flows in a bubble column is being developed. The approach uses an Eulerian analysis of gas liquid flows in the bubble column, and makes use of the Lagrangian particle tracking procedure to analyze the particle motions. Progress was also made in developing a rate dependent thermodynamically consistent model for multiphase slurry flows in a state of turbulent motion. The new model includes the effect of phasic interactions and leads to anisotropic effective phasic stress tensors. Progress was also made in measuring concentration and velocity of particles of different sizes near a wall in a duct flow. The formulation of a thermodynamically consistent model for chemically active multiphase solid-fluid flows in a turbulent state of motion was also initiated. The general objective of this project is to provide the needed fundamental understanding of three-phase slurry reactors in Fischer-Tropsch (F-T) liquid fuel synthesis. The other main goal is to develop a computational capability for predicting the transport and processing of three-phase coal slurries. The specific objectives are: (1) To develop a thermodynamically consistent rate-dependent anisotropic model for multiphase slurry flows with and without chemical reaction for application to coal liquefaction. Also to establish the material parameters of the model. (2) To provide experimental data for phasic fluctuation and mean velocities, as well as the solid volume fraction in the shear flow devices. (3) To develop an accurate computational capability incorporating the new rate-dependent and anisotropic model for analyzing reacting and

  19. Intelligent System for Diagnosis of a Three-Phase Separator

    Directory of Open Access Journals (Sweden)

    Irina Ioniţă

    2016-03-01

    Full Text Available Intelligent systems for diagnosis have been used in a variety of domains: financial evaluation, credit scoring problem, identification of software and hardware problems of mechanical and electronic equipment, medical diagnosis, fault detection in gas-oil production plants etc. The goal of diagnosis systems is to classify the observed symptoms as being caused by some diagnosis class while advising systems perform such a classification and offer corrective remedies (recommendations. The current paper discuss the opportunity to combine more intelligent techniques and methodologies (intelligent agents, data mining and expert systems to increase the accuracy of results obtained from the diagnosis of a three-phase separator. The results indicate that the diagnosis hybrid system benefits from the advantages of each module component: intelligent agent module, data mining module and expert system module.

  20. Evaluation of Three-Phase Transformerless Photovoltaic Inverter Topologies

    DEFF Research Database (Denmark)

    Kerekes, Tamas; Liserre, Marco; Teodorescu, Remus

    2009-01-01

    This paper analyzes and compares three transformerless photovoltaic inverter topologies for three-phase grid connection with the main focus on the safety issues that result from the lack of galvanic isolation. A common-mode model, valid at frequencies lower than 50 kHz, is adopted to study...... the leakage current paths. The model is validated by both simulation and experimental results. These will be used to compare the selected topologies, and to explain the influence of system unbalance and the neutral conductor inductance on the leakage current. It will be demonstrated that the later has...... a crucial influence. Finally, a comparison of the selected topologies is carried out, based on the adopted modulation, connection of the neutral and its inductance, effects of unbalance conditions, component ratings, output voltage levels, and filter size....

  1. Mucormycosis and bone scintillography of three phases. Case description

    International Nuclear Information System (INIS)

    Papadakis S, M.; Larrea R, E.; Carrasco R, C.A.; Garrido A, R.A.; Olmedo T, D.; Perez C, M.

    2007-01-01

    The purpose of presenting this work, besides the interest that shows the mucormycosis pathology not so frequent, it is to carry out a clinical correlation photographic with the imagenology, particularly with the bone scintillography. In the Nuclear Medicine Service it is carried out bone scintillography of three phases previous endovenous administration of 30 mCi (1110 MBq) of 99m Tc-MDP. The images are obtained with a gamma camera model Elscint APEX SPX, first each 2 seconds during the first minute, then early image to the 5 minutes and finally the late ones to the 3 hs. The bone scintillography in the phases 2 and 3 detects bigger radioactive density in left hemi side, with increment of the osteoblast activity mainly in the medial border and the floor of the orbit, in the malar bone and a little more tenuous in the superior maxillary. (Author)

  2. Three-phase radionuclide bone imaging in sports medicine

    International Nuclear Information System (INIS)

    Rupani, H.D.; Holder, L.E.; Espinola, D.A.; Engin, S.I.

    1985-01-01

    Three-phase radionuclide bone (TPB) imaging was performed on 238 patients with sports-related injuries. A wide variety of lesions was encountered, but the most frequent lesions seen were stress fractures of the lower part of the leg at the junction of the middle and distal thirds of the posterior tibial cortex (42 of 79 lesions). There were no differences in the type, location, or distribution of lesions between males and females or between competitive and noncompetitive athletes. In 110 cases, bone stress lesions were often diagnosed when radiographs were normal, whereas subacute or chronic soft-tissue abnormalities had few specific scintigraphic features. TPB imaging provides significant early diagnostic information about bone stress lesions. Normal examination results (53 cases) exclude underlying osseous pathologic conditions

  3. Myositis ossificans and the three-phase bone scan

    International Nuclear Information System (INIS)

    Drane, W.E.

    1984-01-01

    Myositis ossificans circumscripta (or paraosteoarthropathy) in paraplegics has been a well known entity since its classic description in 1918 by Dejerine and Ceillier. The disease is characterized by ectopic bone formation, primarily occurring in the particular soft tissues of the hips and knees. Hypotheses concerning its origin have been proposed, but its etiology is still unknown. Myositis ossificans can occur after traumatic injury, but develops in paraplegics without apparent injury in the involved regions. Radionuclide techniques have been used in the evaluation of myositis ossificans, particularly with serial studies to stage the activity of the disease. The author reports a case of myositis ossificans in a paraplegic that emphasizes the benefit of the three-phase bone scan in the early diagnosis of this disorder

  4. Speed-controlled three-phase drives. Drehzahlgeregelte Drehstromantriebe

    Energy Technology Data Exchange (ETDEWEB)

    Steinmetz, E

    1981-01-01

    Present semiconductor circuit elements have made it possible to produce frequency converters for speed-controlled three-phase drives from the k'' range to the MW range at low cost. Line-powered frequency converter circuits are already in the standardisation stage while the development trends in the field of speed-controlled frequency converter circuits are not foreseeable as yet. Recent developments in the field of electronics have made the circuits simpler and able to implement an increasing number of functions. There is a trend towards programmable digital control systems with microcomputers. Of the 8 articles in the publication, the contribution by M. Wild and R. Wetzl (Synchronous motors with frequency converters drive boiler feed pumps at Bergkamen power plant) has been entered in the data base as a separate citation.

  5. Advanced nonlinear control of three phase series active power filter

    Directory of Open Access Journals (Sweden)

    Abouelmahjoub Y.

    2014-01-01

    Full Text Available The problem of controlling three-phase series active power filter (TPSAPF is addressed in this paper in presence of the perturbations in the voltages of the electrical supply network. The control objective of the TPSAPF is twofold: (i compensation of all voltage perturbations (voltage harmonics, voltage unbalance and voltage sags, (ii regulation of the DC bus voltage of the inverter. A controller formed by two nonlinear regulators is designed, using the Backstepping technique, to provide the above compensation. The regulation of the DC bus voltage of the inverter is ensured by the use of a diode bridge rectifier which its output is in parallel with the DC bus capacitor. The Analysis of controller performances is illustrated by numerical simulation in Matlab/Simulink environment.

  6. Transient three-phase three-component flow. Pt. 3

    International Nuclear Information System (INIS)

    Kolev, N.I.

    1986-05-01

    A mathematical model of a transient three-dimensional three-phase three-component flow described by three-velocity fields in porous body is presented. A combination of separated mass and energy equations together with mixture momentum equations for the flow is used. The mixture equations are used in diffusion form with the assumption that the diffusion velocity can be calculated from empirical correlations. An analytical coupling between the governing equations is developed for calculation of the pressure field. The system is discretized semiimplicitly in 3D-cylindrical space and different solution methods for the algebraic problem are presented. Finally, numerical examples and comparisons with experimental data demonstrate that the method presented is a powerful tool for numerical multiphase flow simulation. (orig.) [de

  7. Adjusting for Misclassification: A Three-Phase Sampling Approach

    Directory of Open Access Journals (Sweden)

    Sang Hailin

    2017-03-01

    Full Text Available The United States Department of Agriculture’s National Agricultural Statistics Service (NASS conducts the June Agricultural Survey (JAS annually. Substantial misclassification occurs during the prescreening process and from field-estimating farm status for nonresponse and inaccessible records, resulting in a biased estimate of the number of US farms from the JAS. Here, the Annual Land Utilization Survey (ALUS is proposed as a follow-on survey to the JAS to adjust the estimates of the number of US farms and other important variables. A three-phase survey design-based estimator is developed for the JAS-ALUS with nonresponse adjustment for the second phase (ALUS. A design-unbiased estimator of the variance is provided in explicit form.

  8. A NOVEL THREE PHASE UNITY POWER FACTOR CONVERTER

    Directory of Open Access Journals (Sweden)

    Bekir Sami SAZAK

    1998-03-01

    Full Text Available The proposed unity power factor converter system which is able to operate from a 150V three-phase supply whilst delivering the required 200V DC voltage has been built and tested. This circuit functions as a high power factor low harmonic rectifier based on the concept that the peak capacitor voltages are proportional to the line input currents. Hence the low frequency components of the capacitor voltages are also approximately proportional to the line input currents. The system can be designed to achieve nearly sinusoidal supply input currents, when operated with discontinuous resonant capacitor voltages Output power control is achieved by variations of the IGBTs switching frequency. The converter is therefore able to compensate for any changes in the load resistance. The proposed topology offers advantages, including: a relatively simple power, control and protection circuits, high power capability, and high converter efficiencies.

  9. Three Phase Bone Scintigraphy in Active and Inactive Osteomyelitis

    International Nuclear Information System (INIS)

    Yang, Woo Jin; Chung, Soo Kyo; Ha, Hyun Kwon; Bahk, Yong Whee

    1988-01-01

    To Appreciate the value of bone scintigraphy in determination of the bony infection, we performed three phase bone scintigraphy in 34 cases of osteomyelitis of extremities prospectively. They were clinically inactive in 11 and active in 23 cases. We confirmed the active osteomyelitis by operation or aspiration within one week after scintigraphy. Perfusion, blood pool and delayed images were analyzed respectively and compared with the plain roentgenograms. All 23 active lesions showed diffusely increased perfusion in affected limbs. The areas of the increased activities on blood pool images were larger than or similar to those on delayed images in 17 cases (73.9%) with active osteomyelitis and smaller in 6 cases (26.1%). 5 of the latter 6 cases showed definite soft tissue activities on blood pool images. In inactive cases bone scintigrams were completely normal in 4 cases. Two of those were normal on plain films and remaining two showed mild focal bony sclerosis. Among 7 inactive lesions, perfusion was normal in 2 cases, diffusely increased in 4 cases and diffusely decreased in 1 case. 6 of these 7 cases showed increased activities both on blood pool and delayed images and the areas of increased activities on blood pool images didn't exceed those on delayed images. Bony sclerosis was noted on plain films in those 7 inactive lesions and the extent of the sclerosis correlated well to delayed images. Large blood pool activity was characteristics of active osteomyelitis. Normal three phase bone scintigram may indicate the time to terminate the treatment, but increased activity on perfusion and blood pool scans is not absolute indication of active lesion if the extent of the lesion on the blood pool image is smaller than that on delayed image and if no definite soft tissue activity is noted on perfusion and blood pool images in clinically inactive patient.

  10. Three-Phase Bone Scintigraphic Diagnosis of Acute Transient Synovitis

    International Nuclear Information System (INIS)

    Chung, Soo Kyo; Lee, Myung Hee; Kim, Choon Yul; Bahk, Yong Whee

    1985-01-01

    Acute transient synovitis of the hip presents clinically pain and limping. But in the majority of the cases, definite positive findings are not manifest in roentgenogram in its early phase. However radionuclide bone imaging combines with the assessment of vascularization and bone tracer uptake is of great value in solving this diagnostic problem. The materials for this study consisted of 29 children with acute transient synovitis of the hip, characterized by symptoms and physical signs of an arthritis, negative X-ray findings and disappearance of all symptoms and signs within a short period of time. They were twenty males and 9 females and age ranged from 1 to 12 years. We took pelvic roentgenogram in AP and frog-leg views. After intravenous bolus injection of 10 to 15 mCi of 99m Tc-methylene diphosphonate, 24 sequential image of the pelvis was taken at 2-second interval for blood flow study. The scintigrams were made using a gamma camera with high resolution parallel hole collimator. Blood pool imaging was obtained at 2 minutes after tracer administration. After 3 hours, static images were taken and then close-up image of the hip using pin-hole collimator was followed. The results were as follows: 1) Bone scintigram was much more sensitive than conventional roentgenogram in diagnosis of acute transient synovitis of the hip. 2) Three-phase imagings showed increased vascular activities in blood pool scintigrams in 96%. 3) Pin-hole imaging showed increased tracer uptake in the regional bones of the hip, particularly in the medial aspect of femoral head and acetabulum. 4) We confirmed that three-phase imaging reinforced with pin-hale technique were very useful in diagnose of acute transient synovitis of the hip.

  11. Ionospheric research for space weather service support

    Science.gov (United States)

    Stanislawska, Iwona; Gulyaeva, Tamara; Dziak-Jankowska, Beata

    2016-07-01

    Knowledge of the behavior of the ionosphere is very important for space weather services. A wide variety of ground based and satellite existing and future systems (communications, radar, surveillance, intelligence gathering, satellite operation, etc) is affected by the ionosphere. There are the needs for reliable and efficient support for such systems against natural hazard and minimalization of the risk failure. The joint research Project on the 'Ionospheric Weather' of IZMIRAN and SRC PAS is aimed to provide on-line the ionospheric parameters characterizing the space weather in the ionosphere. It is devoted to science, techniques and to more application oriented areas of ionospheric investigation in order to support space weather services. The studies based on data mining philosophy increasing the knowledge of ionospheric physical properties, modelling capabilities and gain applications of various procedures in ionospheric monitoring and forecasting were concerned. In the framework of the joint Project the novel techniques for data analysis, the original system of the ionospheric disturbance indices and their implementation for the ionosphere and the ionospheric radio wave propagation are developed since 1997. Data of ionosonde measurements and results of their forecasting for the ionospheric observatories network, the regional maps and global ionospheric maps of total electron content from the navigational satellite system (GNSS) observations, the global maps of the F2 layer peak parameters (foF2, hmF2) and W-index of the ionospheric variability are provided at the web pages of SRC PAS and IZMIRAN. The data processing systems include analysis and forecast of geomagnetic indices ap and kp and new eta index applied for the ionosphere forecasting. For the first time in the world the new products of the W-index maps analysis are provided in Catalogues of the ionospheric storms and sub-storms and their association with the global geomagnetic Dst storms is

  12. "Research Tools": Tools for supporting research and publications

    OpenAIRE

    Ebrahim, Nader Ale

    2014-01-01

    Research Tools” can be defined as vehicles that broadly facilitate research and related activities. “Research Tools” enable researchers to collect, organize, analyze, visualize and publicized research outputs. Dr. Nader has collected over 700 tools that enable students to follow the correct path in research and to ultimately produce high-quality research outputs with more accuracy and efficiency. It is assembled as an interactive Web-based mind map, titled “Research Tools”, which is updated ...

  13. Research and Support for MTLS Data Management and Visualization

    Science.gov (United States)

    2016-09-30

    This report documents the research project "Research and Support for MTLS Data Management and Visualization." The primary goal of the project was to support Caltrans District 4 in their upgrade and enhancement efforts for Mobile Terrestrial Laser Sca...

  14. Institutional Support : Centre for Research and Technology ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    year-old science and technology research centre at Maseno University in western Kenya. The Centre focuses on science and technology research to influence both national policies and development practices at the community level. Currently ...

  15. Institutional Support : Research on Poverty Alleviation (REPOA ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    -established and well-managed independent policy research organization with a record of producing high-quality, policy-relevant research results. REPOA is experiencing rapid growth in the demand for its services. This grant from IDRC's ...

  16. Novel Topology of Three-Phase Electric Spring and Its Control

    DEFF Research Database (Denmark)

    Wang, Qingsong; Cheng, Ming; Jiang, Yunlei

    2017-01-01

    A novel topology is proposed for three-phase electric spring (TPES) to achieve specific functionalities. With respect to the existing one, the novel topology contains an additional three-phase transformer with the primaries located at the position of the non-critical three-phase load (NCL......) of the existing topology and its secondaries connected to the new three-phase NCL, thus forming a new three-phase smart load (SL). To control the novel topology, the so-called modified δ control utilized for the single-phase electric springs is extended to the three-phase case. Thanks to these solutions, TPES...

  17. Mathematical modeling of a three-phase trickle bed reactor

    Directory of Open Access Journals (Sweden)

    J. D. Silva

    2012-09-01

    Full Text Available The transient behavior in a three-phase trickle bed reactor system (N2/H2O-KCl/activated carbon, 298 K, 1.01 bar was evaluated using a dynamic tracer method. The system operated with liquid and gas phases flowing downward with constant gas flow Q G = 2.50 x 10-6 m³ s-1 and the liquid phase flow (Q L varying in the range from 4.25x10-6 m³ s-1 to 0.50x10-6 m³ s-1. The evolution of the KCl concentration in the aqueous liquid phase was measured at the outlet of the reactor in response to the concentration increase at reactor inlet. A mathematical model was formulated and the solutions of the equations fitted to the measured tracer concentrations. The order of magnitude of the axial dispersion, liquid-solid mass transfer and partial wetting efficiency coefficients were estimated based on a numerical optimization procedure where the initial values of these coefficients, obtained by empirical correlations, were modified by comparing experimental and calculated tracer concentrations. The final optimized values of the coefficients were calculated by the minimization of a quadratic objective function. Three correlations were proposed to estimate the parameters values under the conditions employed. By comparing experimental and predicted tracer concentration step evolutions under different operating conditions the model was validated.

  18. Bone graft viability evaluated by three phase bone scan

    International Nuclear Information System (INIS)

    Ljiljana Jaukovic Rajko Spaic; Marijan Novakovic; Srbislav Stosic

    2004-01-01

    Bone defects resulting war injury can be replaced by microvascular bone grafts from fibula. Aim: The aim of this study was to assess the value of three phase (3P) bone scintigraphy in the early detection of the bone graft complications. Method: 3P bone scans were performed in four patients (two after mandible reconstruction with micro vascular fibular bone grafts, one after fibular transplantation for ulnar and one with humeral reconstruction). First dynamic phase scan was performed immediately after iv injection of 740 MBq Tc- 99m DPD, acquiring 15 two seconds duration frames. Second, early static scan was performed during next 300 seconds, and third, delayed scan three hours later. All scans were obtained under the bone graft region. The scans were evaluated using ROI under graft region and the corresponding contra lateral area. Blood flow in graft region was determined using first phase scan, and tracer uptake in the same region was determined using second and third phase scans. Results: in all patients blood flow in graft region was particularly normal. Tracer uptake in one of two patients with mandible reconstruction was diffusely increased in graft, strongly suggesting infection; In the other patient delayed scan showed no tracer uptake in graft center .Both patients with ulnar and humeral reconstruction showed only slightly decreased tracer uptake in bone grafts. 3 phase bone scintigraphy may play a role in the evaluation of bone graft viability by predicting the infection and necrosis. (authors)

  19. ISOBUTANOL FROM SYNGAS IN A THREE PHASE SYSTEM

    Energy Technology Data Exchange (ETDEWEB)

    Peter Tijrn

    2002-12-29

    With growing interest in oxygenates as octane booster for automotive fuels, various synthesis routes for these chemicals are being investigated. Among others, alternative routes to isobutene, the C4-components in MTBE-synthesis are under investigation. A promising path to isobutene is the heterogeneously catalyzed CO-hydrogenation to isobutanol with following dehydration (Fig. 1). As shown by thermodynamical studies, the heterogeneously catalyzed CO-hydrogenation to isobutanol is not expected to experience any thermodynamic constraints. However, heterogeneous hydrogenation of CO is a very exothermic process, a problem which can only be partly solved when being conducted in a plug flow reactor. When carried out in reaction vessels with moving catalyst bed (e.g. three phase stirred tank), heat transfer problems can be resolved, along with additional benefits connected with this reactor type. Several heterogeneous catalytic systems have been under investigation for their capability of isobutanol synthesis from syngas. Most promising catalysts for an active and selective isobutanol synthesis from CO are modified high temperature methanol catalysts.

  20. Clinical significant of three phase radionuclide bone scan

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Sun Hee; Suh, Jin Suck; Park, Chang Yun [Yonsei University College of Medicine, Seoul (Korea, Republic of)

    1989-04-15

    Three phase radionuclide bone scan, consisting of a radionuclide angiogram, an immediate postinjection blood pool image, and 4hr delayed images, was randomly performed in 182 patients, who had been suffered from either local pain or tenderness. Authors analysed 3 phase bone scan in 74 patients with correct diagnosis proven surgically or clinically, from July 1987 to August, 1988. The results were as follows: 1. Overall sensitivity of 3 phase bone scan was 85.4%: sensitivity in patients with an osseous lesion was 90.4% as opposed to 72.7% in patients with a nonosseous lesion. 2. There was no difference in the detection rate of the osseous lesions between the 3 phase bone scan and the delayed image bone scan. However, because the detection rate was higher on the 3 phase bone scan than it was on only the delayed image bone scan (55%) in instance of the nonosseous lesion, we would suggest that 3 phase bone scan might be obtained in cases suspected of the nonosseous lesions. 3. When the presumptive diagnosis was a bone tumor, sensitivity and specificity for malignancy were 67%, 100% respectively. 4. In differentiating osteomyelitis from cellulitis, sensitivity was 94%, specificity was 100%. 5. 3 phase bone scan was able to provide the precise information about either vasculaturity or localization of lesion in some cases of soft tissue mass and avascular necrosis of hips.

  1. Technical Support DLA Apparel Research Network

    National Research Council Canada - National Science Library

    Guthrie, Jeffrey

    2002-01-01

    The Defense Logistics Agency's Research and Development Enterprise Division established a network of universities, equipment suppliers, apparel manufacturers, industry consultants and software developers...

  2. Institutional Support : Applied and Theoretical Economic Research ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    This grant from IDRC's Think Tank Initiative will allow GREAT to recruit fulltime research staff, enhance researcher training, formulate a strategic plan, upgrade the information infrastructure, and put ... IDRC is pleased to announce the results of its 2017 call for proposals to establish Cyber Policy Centres in the Global South.

  3. Research support services for IDRC grantees

    International Development Research Centre (IDRC) Digital Library (Canada)

    Melanie Brunet

    Research help:The Librarian can… • Assist you in defining search strategies (key concepts and relevant resources). • Show you how to search databases and free online resources. • Help with complex literature searches. • Provide advice on selecting a journal for open access publication of your research results. Full text of ...

  4. Research to Support Intelligent Data Management

    Science.gov (United States)

    Lerner, Bao-Ting

    1998-01-01

    This final report details the contract performance and analysis of research and development results obtained during the contract period. KT-TECH's research and development work results in the areas of registration of remotely sensed data and the test evaluation and porting of the Regional Validation Center software system, are presented.

  5. Expanding Library Support of Faculty Research: Exploring Readiness

    Science.gov (United States)

    Brown, Jeanne M.; Tucker, Cory

    2013-01-01

    The changing research and information environment requires a reexamination of library support for research. This study considers research-related attitudes and practices to identify elements indicating readiness or resistance to expanding the library's role in research support. A survey of faculty conducted at the University of Nevada Las Vegas…

  6. High Efficiency Three-phase Power Factor Correction Rectifier using Wide Band-Gap Devices

    DEFF Research Database (Denmark)

    Kouchaki, Alireza

    Improving the conversion efficiency of power factor correction (PFC) rectifiers has become compelling due to their wide applications such as adjustable speed drives, uninterruptible power supplies (UPS), and battery chargers for electric vehicles (EVs). The attention to PFCs has increased even more....... Therefore, current controllers are also important to be investigated in this project. In this PhD research work, a comprehensive design of a two-level three-phase PFC rectifier using silicon-carbide (SiC) switches to achieve high efficiency is presented. The work is divided into two main parts: 1) Optimum...

  7. UPS fellowships support creative engineering research

    OpenAIRE

    Crumbley, Liz

    2007-01-01

    A new $40,000 grant marks the 11th anniversary of support from the United Parcel Service (UPS) Foundation for doctoral fellowships in the Human Factors and Safety Engineering Graduate Program in the Grado Department of Industrial and Systems Engineering (ISE) in the College of Engineering.

  8. ADVANCED COMPUTATIONAL MODEL FOR THREE-PHASE SLURRY REACTORS

    International Nuclear Information System (INIS)

    Ahmadi, Goodarz

    2004-01-01

    In this project, an Eulerian-Lagrangian formulation for analyzing three-phase slurry flows in a bubble column was developed. The approach used an Eulerian analysis of liquid flows in the bubble column, and made use of the Lagrangian trajectory analysis for the bubbles and particle motions. The bubble-bubble and particle-particle collisions are included the model. The model predictions are compared with the experimental data and good agreement was found An experimental setup for studying two-dimensional bubble columns was developed. The multiphase flow conditions in the bubble column were measured using optical image processing and Particle Image Velocimetry techniques (PIV). A simple shear flow device for bubble motion in a constant shear flow field was also developed. The flow conditions in simple shear flow device were studied using PIV method. Concentration and velocity of particles of different sizes near a wall in a duct flow was also measured. The technique of Phase-Doppler anemometry was used in these studies. An Eulerian volume of fluid (VOF) computational model for the flow condition in the two-dimensional bubble column was also developed. The liquid and bubble motions were analyzed and the results were compared with observed flow patterns in the experimental setup. Solid-fluid mixture flows in ducts and passages at different angle of orientations were also analyzed. The model predictions were compared with the experimental data and good agreement was found. Gravity chute flows of solid-liquid mixtures were also studied. The simulation results were compared with the experimental data and discussed A thermodynamically consistent model for multiphase slurry flows with and without chemical reaction in a state of turbulent motion was developed. The balance laws were obtained and the constitutive laws established

  9. NRC safety research in support of regulation

    International Nuclear Information System (INIS)

    1994-06-01

    This report, the ninth in a series of annual reports, was prepared in response to congressional inquiries concerning how nuclear regulatory research is used. It summarizes the accomplishments of the Office of Nuclear Regulatory Research during FY 1993. A special emphasis on accomplishments in nuclear power plant aging research reflects recognition that number of plants are entering the final portion of their original 40-year operating licenses and that, in addition to current aging effects, a focus on safety considerations for license renewal becomes timely. The primary purpose of performing regulatory research is to develop and provide the Commission and its staff with sound technical bases for regulatory decisions on the safe operation of licensed nuclear reactors and facilities, to find unknown or unexpected safety problems, and to develop data and related information for the purpose of revising the Commission's rules, regulatory guides, or other guidance

  10. Research Award: Supporting Inclusive Growth program Deadline ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    Jean-Claude Dumais

    2012-09-12

    Sep 12, 2012 ... results, participating in project development, monitoring, communication and learning activities, and preparing internal and external reports. Candidates should have the following qualifications: • Strong research, analysis, and writing skills for different audiences (academic, policy, general public);.

  11. Federal Support for Research and Development

    National Research Council Canada - National Science Library

    Campbell, Sheila

    2007-01-01

    ...-being. Private businesses are the largest sponsors of research and development (R&D) in the United States, producing the discoveries that in turn lead to new products and services and the growth of productivity...

  12. NCDP Research Projects and Research Supported Projects (June ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    Amal Ben Ameur

    prevent non-communicable diseases in India. 139,600. India. Asia ... Building the field of research on non- ... Assessing the attitudes and practices of public ... Tobacco control Research on health costs of smoking in Cambodia. 14,800.

  13. Supporting research projects via student workshops

    DEFF Research Database (Denmark)

    Marschall, Max; Schmeck, Michel; Gengnagel, Christoph

    2016-01-01

    As part of a joint research project between the Centre for Information Technology and Architecture (CITA) and te Department for Structural Design and Technology (KET), a one week student workshop was organised at the Royal Danish Academy of Fine Arts (KADK) in Copenhagen. This paper outlines...... the teaching methods applied to reach maximum insight from student interaction, despite the unfamiliarity the students had with the research matter: physical and numeric form-finding for lightweight hybrid structures. Hybrid structures are defined here as combining different components of low stiffness...

  14. Seismic research in support of reactor technology

    International Nuclear Information System (INIS)

    Gantenbein, F.

    1991-01-01

    This paper gives an overview of various topics related to the seismic analysis of nuclear power plants which are soil structure interaction, analytical methods for equipment analysis with linear or non linear behavior. In addition comments on piping system behavior and experimental analysis will be given. The research which is undertaken in CEA/DMT on these topics will also be described

  15. Supporting Theory Building in Integrated Services Research

    Science.gov (United States)

    Robinson, Mark; Atkinson, Mary; Downing, Dick

    2008-01-01

    This literature review was commissioned by the National Foundation for Educational Research (NFER) to draw together current and recent studies of integrated working, in order to build an overview of the theories and models of such working. The review is important for current work on evaluating the early impact of integrated children's services and…

  16. Institutional Support : Ethiopian Development Research Institute ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    The Ethiopian Development Research Institute (EDRI) was established in 1999 and became operational in 2003 as a semi-autonomous organization accountable to ... International Water Resources Association, in close collaboration with IDRC, is holding a webinar titled “Climate change and adaptive water management: ...

  17. Decision Strategy Research and Policy Support

    International Nuclear Information System (INIS)

    Hardeman, F.

    2002-01-01

    The objective of SCK-CEN's R and D programme on decision strategies and policy support is: (1) to investigate the decision making process, with all its relevant dimensions, in the context of radiation protection or other nuclear issues (with particular emphasis on emergency preparedness); (2) to disseminate knowledge on decision making and nuclear emergencies, including the organisation of training courses, the contribution to manuals or guidelines, the participation in working groups or discussion forums; (3) to assist the authorities and the industry on any topic related to radiation protection and to make expertise and infrastructure available; (4) to participate in and contribute to initiatives related to social sciences and their implementation into SCK-CEN; (5) to co-ordinate efforts of SCK-CEN related to medical applications of ionising radiation. Principal achievements in 2001 are described

  18. Decision Strategy Research and Policy Support

    Energy Technology Data Exchange (ETDEWEB)

    Hardeman, F

    2002-04-01

    The objective of SCK-CEN's R and D programme on decision strategies and policy support is: (1) to investigate the decision making process, with all its relevant dimensions, in the context of radiation protection or other nuclear issues (with particular emphasis on emergency preparedness); (2) to disseminate knowledge on decision making and nuclear emergencies, including the organisation of training courses, the contribution to manuals or guidelines, the participation in working groups or discussion forums; (3) to assist the authorities and the industry on any topic related to radiation protection and to make expertise and infrastructure available; (4) to participate in and contribute to initiatives related to social sciences and their implementation into SCK-CEN; (5) to co-ordinate efforts of SCK-CEN related to medical applications of ionising radiation. Principal achievements in 2001 are described.

  19. Water Resources Research supports water economics submissions

    Science.gov (United States)

    Griffin, Ronald C.

    2012-09-01

    AGU's international interdisciplinary journal Water Resources Research (WRR) publishes original contributions in hydrology; the physical, chemical, and biological sciences; and the social and policy sciences, including economics, systems analysis, sociology, and law. With the rising relevance of water economics and related social sciences, the editors of WRR continue to encourage submissions on economics and policy. WRR was originally founded in the mid 1960s by Walter Langbein and economist Allen Kneese. Several former WRR editors have been economists—including David Brookshire, Ron Cummings, and Chuck Howe—and many landmark articles in water economics have been published in WRR.

  20. Supporting Solar Physics Research via Data Mining

    Science.gov (United States)

    Angryk, Rafal; Banda, J.; Schuh, M.; Ganesan Pillai, K.; Tosun, H.; Martens, P.

    2012-05-01

    In this talk we will briefly introduce three pillars of data mining (i.e. frequent patterns discovery, classification, and clustering), and discuss some possible applications of known data mining techniques which can directly benefit solar physics research. In particular, we plan to demonstrate applicability of frequent patterns discovery methods for the verification of hypotheses about co-occurrence (in space and time) of filaments and sigmoids. We will also show how classification/machine learning algorithms can be utilized to verify human-created software modules to discover individual types of solar phenomena. Finally, we will discuss applicability of clustering techniques to image data processing.

  1. Problems of information support in scientific research

    Science.gov (United States)

    Shamaev, V. G.; Gorshkov, A. B.

    2015-11-01

    This paper reports on the creation of the open access Akustika portal (AKDATA.RU) designed to provide Russian-language easy-to-read and search information on acoustics and related topics. The absence of a Russian-language publication in foreign databases means that it is effectively lost for much of the scientific community. The portal has three interrelated sections: the Akustika information search system (ISS) (Acoustics), full-text archive of the Akusticheskii Zhurnal (Acoustic Journal), and 'Signal'naya informatsiya' ('Signaling information') on acoustics. The paper presents a description of the Akustika ISS, including its structure, content, interface, and information search capabilities for basic and applied research in diverse areas of science, engineering, biology, medicine, etc. The intended users of the portal are physicists, engineers, and engineering technologists interested in expanding their research activities and seeking to increase their knowledge base. Those studying current trends in the Russian-language contribution to international science may also find the portal useful.

  2. National Biological Service Research Supports Watershed Planning

    Science.gov (United States)

    Snyder, Craig D.

    1996-01-01

    The National Biological Service's Leetown Science Center is investigating how human impacts on watershed, riparian, and in-stream habitats affect fish communities. The research will provide the basis for a Ridge and Valley model that will allow resource managers to accurately predict and effectively mitigate human impacts on water quality. The study takes place in the Opequon Creek drainage basin of West Virginia. A fourth-order tributary of the Potomac, the basin falls within the Ridge and Valley. The study will identify biological components sensitive to land use patterns and the condition of the riparian zone; the effect of stream size, location, and other characteristics on fish communities; the extent to which remote sensing can reliable measure the riparian zone; and the relationship between the rate of landscape change and the structure of fish communities.

  3. Aerodynamics support of research instrument development

    Science.gov (United States)

    Miller, L. Scott

    1990-09-01

    A new velocimetry system is currently being developed at NASA LaRC. The device, known as a Doppler global velocimeter (DGV), can record three velocity components within a plane simultaneously and in near real time. To make measurements the DGV, like many other velocimetry systems, relies on the scattering of light from numerous small particles in a flow field. The particles or seeds are illuminated by a sheet of laser light and viewed by two CCD cameras. The scattered light from the particles will have a frequency which is a function of the source laser light frequency, the viewing angle, and most importantly the seed velocities. By determining the scattered light intensity the velocity can be measured at all points within the light sheet simultaneously. Upon completion of DGV component construction and initial check out a series of tests in the Basic Aerodynamic Research (wind) Tunnel (BART) are scheduled to verify instrument operation and accuracy. If the results are satisfactory, application of the DGV to flight measurements on the F-18 High Alpha Research Vehicle (HARV) are planned. The DGV verification test in the BART facility will utilize a 75 degree swept delta wing model. A major task undertaken this summer included evaluation of previous results for this model. A specific series of tests matching exactly the previous tests and exploring new DGV capabilities were developed and suggested. Another task undertaken was to study DGV system installation possibilities in the F-18 HARV aircraft. In addition, a simple seeding system modification was developed and utilized to make Particle Imaging Velocimetry (PIV) measurements in the BART facility.

  4. A New 4D Imaging Method for Three-Phase Analogue Experiments in Volcanology (and Other Three-Phase Systems)

    Science.gov (United States)

    Oppenheimer, J.; Patel, K. B.; Lev, E.; Hillman, E. M. C.

    2017-12-01

    Bubbles and crystals suspended in magmas interact with each other on a small scale, which affects large-scale volcanic processes. Studying these interactions on relevant scales of time and space is a long-standing challenge. Therefore, the fundamental explanations for the behavior of bubble- and crystal-rich magmas are still largely speculative. Recent application of X-ray tomography to experiments with synthetic magmas has already improved our understanding of small-scale 4D (3D + time) phenomena. However, this technique has low imaging rates Confocally Aligned Planar Excitation (SCAPE) microscopy. This method based on laser-fluorescence has been used to image live biological processes at high speed and in 3D. It allows imaging rates of up to several hundred vps and image volumes up to 1 x 1 x 0.5 mm3, with a trade-off between speed and spatial resolution. We ran two sets of experiments with silicone oil and soda-lime glass beads of <50 µm diameter, contained within a vertical glass casing 50 x 5 x 4 mm3. We used two different bubble generation methods. In the first set of experiments, small air bubbles (< 1 mm) were introduced through a hole at the bottom of the sample and allowed to rise through a suspension with low-viscosity oil. We successfully imaged bubble rise and particle movements around the bubble. In the second set, bubbles were generated by mixing acetone into the suspension and decreasing the surface pressure to cause a phase change to gaseous acetone. This bubble generation method compared favorably with previous gum rosin-acetone experiments: they provided similar degassing behaviors, along with more control on suspension viscosity and optimal optical properties for laser transmission. Large volumes of suspended bubbles, however, interfered with the laser path. In this set, we were able to track bubble nucleation sites and nucleation rates in 4D. This promising technique allows the study of small-scale interactions in two- and three-phase systems

  5. Review of Operation and Maintenance Support Systems for Research Reactors

    International Nuclear Information System (INIS)

    Jin, Kyungho; Heo, Gyunyoung; Park, Jaekwan

    2014-01-01

    Operation support systems do not directly control the plant but it can aid decision making itself by obtaining and analyzing large amounts of data. Recently, the demand of research reactor is growing and the need for operation support systems is increasing, but it has not been applied for research reactors. This study analyzes operation and maintenance support systems of NPPs and suggests appropriate systems for research reactors based on analysis. In this paper, operation support systems for research reactors are suggested by comparing with those of power reactors. Currently, research reactors do not cover special systems in order to improve safety and operability in comparison with power reactors. Therefore we expect to improve worth to use by introducing appropriate systems for research reactors. In further research, we will develop an appropriate system such as applications or tools that can be applied to the research reactor

  6. TTI Phase 2 Institutional Support: Economic Policy Research Centre ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    TTI Phase 2 Institutional Support: Economic Policy Research Centre ... the Economic Policy Research Centre's (EPRC) role as a credible public policy institution in ... IWRA/IDRC webinar on climate change and adaptive water management.

  7. Building Canadian Support for Global Health Research - Phase III ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    supported researcher is receiving international attention for his work to address maternal and child death rates in East Africa. View moreMaternal and child health research featured in Canadian Geographic ...

  8. Direct-current vector control of three-phase grid-connected rectifier-inverter

    Energy Technology Data Exchange (ETDEWEB)

    Li, Shuhui; Haskew, Timothy A.; Hong, Yang-Ki; Xu, Ling [Department of Electrical and Computer Engineering, University of Alabama, Tuscaloosa, AL 35475 (United States)

    2011-02-15

    The three-phase grid-connected converter is widely used in renewable and electric power system applications. Traditionally, control of the three-phase grid-connected converter is based on the standard decoupled d-q vector control mechanism. Nevertheless, the study of this paper shows that there is a limitation in the conventional standard vector control method. Some of the limitations have also been found recently by other researchers. To overcome the shortage of the conventional vector control technique, this paper proposes a new direct-current d-q vector control mechanism in a nested-loop control structure, based on which an optimal control strategy is developed in a nonlinear programming formulation. The behaviors of both the conventional and proposed control methods are compared and evaluated in simulation and laboratory hardware experiment environments, both of which demonstrates that the proposed approach is effective for grid-connected power converter control in a wide system conditions while the conventional standard vector control approach may behave improperly especially when the converter operates beyond its PWM saturation limit. (author)

  9. Energy-efficient three-phase bidirectional converter for grid-connected storage applications

    International Nuclear Information System (INIS)

    Colmenar-Santos, Antonio; Linares-Mena, Ana-Rosa; Velázquez, Jesús Fernández; Borge-Diez, David

    2016-01-01

    Highlights: • Storage control system developed based on AC DC three phase bidirectional converter. • Bidirectional AC DC converter for storage integration into distribution grids. • Efficiencies over 98% for values over 30% of the bidirectional converter rated power. • Sensitivity analysis of the parameters set by the transmission system operator. • Low-cost option for control and integration of new grid-connected storage systems. - Abstract: Grid connected energy storage systems are expected to play an essential role in the development of Smart Grids, providing, among other benefits, ancillary services to power grids. It is therefore crucial to design and develop control and conversion systems that represent the key instrument where intelligence for decision-making is applied, in order to validate and ensure its optimal operation as part and parcel of the electrical system. The present research describes the design and development of a battery energy storage system based on an AC-DC three-phase bidirectional converter capable of operating either in charge mode to store electrical energy, or in discharge mode to supply load demands. The design is modelled with MATLAB® Simulink® environment in order to evaluate the performance during load variations. Moreover, the assessment is complemented by a global sensitivity analysis for variations in the operating parameters set by the transmission system operator. The effectiveness of the simulation is confirmed by implementing the system and carrying out grid connection tests, obtaining efficiencies over 98% for values over the 30% of the bidirectional converter rated power.

  10. Research Support in Australian Academic Libraries: Services, Resources, and Relationships

    Science.gov (United States)

    Haddow, Gaby; Mamtora, Jayshree

    2017-01-01

    In the last decade Australian academic libraries have increasingly aligned their research support services with assessment criteria used in the national research evaluation exercise (Excellence for Research in Australia). The same period has seen growing interest in research impact outside of traditional measures, such as bibliometrics. Social…

  11. [Support Team for Investigator-Initiated Clinical Research].

    Science.gov (United States)

    Fujii, Hisako

    2017-07-01

    Investigator-initiated clinical research is that in which investigators plan and carry out their own clinical research in academia. For large-scale clinical research, a team should be organized and implemented. This team should include investigators and supporting staff, who will promote smooth research performance by fulfilling their respective roles. The supporting staff should include project managers, administrative personnel, billing personnel, data managers, and clinical research coordinators. In this article, I will present the current status of clinical research support and introduce the research organization of the Dominantly Inherited Alzheimer Network (DIAN) study, an investigator-initiated international clinical research study, with particular emphasis on the role of the project management staff and clinical research coordinators.

  12. 7 CFR 3403.4 - Three-phase program.

    Science.gov (United States)

    2010-01-01

    ... SBIR Program funds. The purpose of the third phase is to pursue the commercial applications or objectives of the research carried out in Phases I and II through the use of private or Federal non-SBIR... proposals) to conduct feasibility-related experimental research and development related to described agency...

  13. Expanding the research area of behavior change support systems

    NARCIS (Netherlands)

    van Gemert-Pijnen, Julia E.W.C.; Reitberger, Wolfgang; Langrial, Sitwat; Ploderer, Bernd; Oinas-Kukkonen, Harri; Berkovsky, Shlomo; Freyne, Jill

    2013-01-01

    The First International Workshop on Behavior Change Support Systems attracted a great research interest. The selected papers focused on abstraction, implementation and evaluation of Behavior Change Support Systems. The workshop is an evidence of how researchers from around the globe have their own

  14. Hybrid Modulation of Bidirectional Three-Phase Dual-Active-Bridge DC Converters for Electric Vehicles

    Directory of Open Access Journals (Sweden)

    Yen-Ching Wang

    2016-06-01

    Full Text Available Bidirectional power converters for electric vehicles (EVs have received much attention recently, due to either grid-supporting requirements or emergent power supplies. This paper proposes a hybrid modulation of the three-phase dual-active bridge (3ΦDAB converter for EV charging systems. The designed hybrid modulation allows the converter to switch its modulation between phase-shifted and trapezoidal modes to increase the conversion efficiency, even under light-load conditions. The mode transition is realized in a real-time manner according to the charging or discharging current. The operation principle of the converter is analyzed in different modes and thus design considerations of the modulation are derived. A lab-scaled prototype circuit with a 48V/20Ah LiFePO4 battery is established to validate the feasibility and effectiveness.

  15. The three phases of life : an inter-cultural perspective

    NARCIS (Netherlands)

    Rauterberg, G.W.M.

    2011-01-01

    This paper presents a new direction of research in entertainment computing. The problem addressed is drawing on results from different disciplines: anthropology, sociology, design, and engineering sciences. Starting with the three divine concepts in Hinduism (Brahma, Vishnu and Shiva) each

  16. Research Training, Institutional Support, and Self-Efficacy: Their Impact on Research Activity of Social Workers

    Directory of Open Access Journals (Sweden)

    Mark Thomas Lynch

    2009-11-01

    Full Text Available While the expectations for social work practitioners to do research have increased, their involvement is still limited. We know little about what factors influence involvement in research. The present study proposes a theoretical model that hypothesizes research training and institutional support for research as the exogenous variables, research self-efficacy as an intervening variable, and research activity as the endogenous variable. The study tests the model using data collected from a random sample of social workers. To a large degree the data support the model. Research self-efficacy has a significant effect on research activity. It is also an important mediating variable for the effect of institutional support on research activity. Although institutional support for research has no direct effect, it has an indirect effect via self-efficacy on research activity. However, research training has no effect on research activity and self-efficacy in research. The implications of these findings are discussed.

  17. Numerical simulation of three phase asynchronous motor to ...

    African Journals Online (AJOL)

    These signatures in other researches are often considered as direct and accurate indicators of a stator winding fault. This similarity leads to uncertainty in the detection of the fault, which makes imperative the use of complementary technique. The focus on the 2nd harmonic of the supply frequency (2.fs) in the torque ...

  18. A proposed clinical research support career pathway for noninvestigators.

    Science.gov (United States)

    Smith, Sheree; Gullick, Janice; Ballard, Jacqueline; Perry, Lin

    2018-03-08

    To discuss the international experience of clinical research support for noninvestigator roles and to propose a new pathway for Australia, to promote a sustainable research support workforce capable of delivering high-quality clinical research. Noninvestigator research support roles are currently characterized by an ad hoc approach to training, with limited role delineation and perceived professional isolation with implications for study completion rates and participant safety. A focused approach to developing and implementing research support pathways has improved patient recruitment, study completion, job satisfaction, and research governance. The Queensland and New South Wales state-based Nurses' Awards, the Australian Qualifications Framework, and a University Professional (Research) Staff Award. Research nurses in the clinical environment improve study coordination, adherence to study protocol, patient safety, and clinical care. A career pathway that guides education and outlines position descriptions and skill sets would enhance development of the research support workforce. This pathway could contribute to changing the patient outcomes through coordination and study completion of high-quality research. A wide consultative approach is required to determine a cost-effective and feasible approach to implementation and evaluation of the proposed pathway. © 2018 John Wiley & Sons Australia, Ltd.

  19. A multi-faceted approach to research development (II): Supporting ...

    African Journals Online (AJOL)

    This article discusses a number of critical areas of research development that have been identified: addressing perceptions and myths about research; management and support; mentoring; engagement with postgraduate programmes; incentives; resources; and creating research initiatives. For each of these critical areas, ...

  20. Supporting Knowledge Mobilization and Research Impact Strategies in Grant Applications

    Science.gov (United States)

    Phipps, David; Jensen, Krista E.; Johnny, Michael; Poetz, Anneliese

    2016-01-01

    Each application to the National Science Foundation (NSF) must contain a Broader Impact (BI) strategy. Similarly, grant applications for most research funders in Canada and the UK require strategies to support the translation of research into impacts on society; however, the guidance provided to researchers is too general to inform the specific…

  1. NRC safety research in support of regulation. Selected highlights

    International Nuclear Information System (INIS)

    1986-05-01

    The report presents selected highlights of how research has contributed to the regulatory effort. It explains the research role of the NRC and nuclear safety research contributions in the areas of: pressure vessel integrity, piping, small- and large-break loss-of-coolant accidents, hydrogen and containment, source term analysis, seismic hazards and high-level waste management. The report also provides a summary of current and future research directions in support of regulation

  2. Mentoring K scholars: strategies to support research mentors.

    Science.gov (United States)

    Burnham, Ellen L; Schiro, Stephanie; Fleming, Michael

    2011-06-01

    The goal of this paper is to present strategies utilized to support K scholar research mentors. K scholars are generally assistant professors who are close to developing independent research programs. Of all the various types of mentees, K scholars offer the greatest challenges, as well as the greatest rewards, for research mentors. To see one's mentee achieve independent PI status and become an established investigator is one of the great joys of being a research mentor. Research mentors for K scholars, however, may not directly benefit from their mentoring relationship, neither in terms of obtaining data to support their research program or laboratory, nor in assistance with grants or scientific papers. There is a pressing need for the research community to address the workload, institutional expectations, and reward system for research mentors. The dearth of research mentors and role models in clinical translational science parallels the decreasing number of physicians choosing careers in clinical research. While there is limited empirical information on the effectiveness of mentor support mechanisms, this white paper concludes that providing mentor support is critical to expanding the available pool of mentors, as well as providing training opportunities for K scholars. © 2011 Wiley Periodicals, Inc.

  3. Research and development activity in support of LCP

    International Nuclear Information System (INIS)

    Lubell, M.S.

    1979-01-01

    The research and development activity (RDAC) established in support of the Large Coil Program (LCP) at Oak Ridge National Laboratory (ORNL) is described. Some experimental results are presented and the importance of the RDAC to the magnet community is discussed

  4. Supporting Research Activities through the Think Tank Initiative-End ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    26 sept. 2014 ... Two research proposals were selected for support. ... teams will conduct a qualitative and quantitative study on policy stakeholders' perceptions on ... and conduct a qualitative evaluation of youth employment program design.

  5. Towards Data Management Planning Support for Research Data

    NARCIS (Netherlands)

    Görzig, Heike; Engel, Felix; Brocks, Holger; Vogel, Tobias; Hemmje, Matthias

    2015-01-01

    Görzig, H., Engel, F., Brocks, H., Vogel, T. & Hemmje, M. (2015, August). Towards Data Management Planning Support for Research Data. Paper presented at the ASE International Conference on Data Science, Stanford, United States of America.

  6. Researchers urge climate-resilience support for South African maize ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    2016-04-20

    Apr 20, 2016 ... Researchers urge climate-resilience support for South African maize farmers ... They found that climate change is likely to hurt livelihoods and food security ... In Burkina Faso, local cultivation and livestock practices are losing ...

  7. University Funding: Federal Funding Mechanisms in Support of University Research.

    Science.gov (United States)

    1986-02-01

    disciplines in elec- tronic sciences. DOE supports a team of researchers in high-energy and nuclear physics through contracts to build customized equipment to...data available on up to 15 federal agen- Collges ,19631982cies, support of science research at universities since 1963. Although not all of the...recent Ph.D. Young Investigators in physicists. High Energy Physics Time in Effect: 1975 to present. Fiscal Year 1984 Average Number of Average

  8. Instantaneous Power Compensation in Three-Phase Systems by Using p-q-r Theory

    DEFF Research Database (Denmark)

    Kim, Hyosung; Blaabjerg, Frede; Bak-Jensen, Birgitte

    2002-01-01

    Three linearly independent instantaneous powers have been defined in the time domain in three-phase four-wire systems with the use of p-q-r theory. Any three-phase circuit can be transformed into three single-phase circuits by the p-q-r transformation Thus the instantaneous powers in any three...

  9. A Three-Phase Boost DC-AC Converter | Odeh | Nigerian Journal of ...

    African Journals Online (AJOL)

    Sliding mode controllers are designed to perform a robust control for the three boost dc-dc converters. Computer simulations and spectral analysis demonstrate the feasibility of the proposed three-phase inverter. The inverter is intended to be used in three-phase electric drives and uninterruptible power supply (UPS) ...

  10. Three-Phase and Six-Phase AC at the Lab Bench

    Science.gov (United States)

    Caplan, George M.

    2009-01-01

    Utility companies generate three-phase electric power, which consists of three sinusoidal voltages with phase angles of 0 degrees, 120 degrees, and 240 degrees. The ac generators described in most introductory textbooks are single-phase generators, so physics students are not likely to learn about three-phase power. I have developed a simple way…

  11. Diagnosis of the three-phase induction motor using thermal imaging

    Science.gov (United States)

    Glowacz, Adam; Glowacz, Zygfryd

    2017-03-01

    Three-phase induction motors are used in the industry commonly for example woodworking machines, blowers, pumps, conveyors, elevators, compressors, mining industry, automotive industry, chemical industry and railway applications. Diagnosis of faults is essential for proper maintenance. Faults may damage a motor and damaged motors generate economic losses caused by breakdowns in production lines. In this paper the authors develop fault diagnostic techniques of the three-phase induction motor. The described techniques are based on the analysis of thermal images of three-phase induction motor. The authors analyse thermal images of 3 states of the three-phase induction motor: healthy three-phase induction motor, three-phase induction motor with 2 broken bars, three-phase induction motor with faulty ring of squirrel-cage. In this paper the authors develop an original method of the feature extraction of thermal images MoASoID (Method of Areas Selection of Image Differences). This method compares many training sets together and it selects the areas with the biggest changes for the recognition process. Feature vectors are obtained with the use of mentioned MoASoID and image histogram. Next 3 methods of classification are used: NN (the Nearest Neighbour classifier), K-means, BNN (the back-propagation neural network). The described fault diagnostic techniques are useful for protection of three-phase induction motor and other types of rotating electrical motors such as: DC motors, generators, synchronous motors.

  12. Pediatric Oncology Branch - Support Services | Center for Cancer Research

    Science.gov (United States)

    Support Services As part of the comprehensive care provided at the NCI Pediatric Oncology Branch, we provide a wide range of services to address the social, psychological, emotional, and practical facets of pediatric cancer and to support patients and families while they are enrolled in clinical research protocols.

  13. Research and Support Strategies For Women's Higher Education.

    Science.gov (United States)

    Babbitt, Samuel F.; And Others

    Inadequate support is presently offered for the study of certain important questions which have serious implications for educational policies affecting women. Priority should be given to the support of those areas of research and program development and evaluation that have the most critical implications for both the higher education of women and…

  14. Supporting Scientific Research with the Energy Sciences Network

    CERN Multimedia

    CERN. Geneva; Monga, Inder

    2016-01-01

    The Energy Sciences Network (ESnet) is a high-performance, unclassified national network built to support scientific research. Funded by the U.S. Department of Energy’s Office of Science (SC) and managed by Lawrence Berkeley National Laboratory, ESnet provides services to more than 40 DOE research sites, including the entire National Laboratory system, its supercomputing facilities, and its major scientific instruments. ESnet also connects to 140 research and commercial networks, permitting DOE-funded scientists to productively collaborate with partners around the world. ESnet Division Director (Interim) Inder Monga and ESnet Networking Engineer David Mitchell will present current ESnet projects and research activities which help support the HEP community. ESnet  helps support the CERN community by providing 100Gbps trans-Atlantic network transport for the LHCONE and LHCOPN services. ESnet is also actively engaged in researching connectivity to cloud computing resources for HEP workflows a...

  15. Analysis of Magnetically-Coupled Impedance Source Three-Phase Four-Switch Inverters

    DEFF Research Database (Denmark)

    Li, Kerui; Abdelhakim, Ahmed; Yang, Yongheng

    2017-01-01

    In this paper, magnetically-coupled impedance source (MCIS) three-phase four-switch inverters are introduced for renewable energy applications. This inverter utilizes two single-phase MCIS inverters to obtain a three-phase output, where less component-count is achieved in order to reduce the inve......In this paper, magnetically-coupled impedance source (MCIS) three-phase four-switch inverters are introduced for renewable energy applications. This inverter utilizes two single-phase MCIS inverters to obtain a three-phase output, where less component-count is achieved in order to reduce...... the inverter volume. On the other hand, as a result of the reduced number of switches, the proposed inverter suffers from higher voltage stresses. The MCIS inverters are first reviewed. Then, the modulation and operation principle of the MCIS three-phase inverter topology are introduced before sizing...

  16. The role of learning technologists in supporting e-research

    Directory of Open Access Journals (Sweden)

    Susi Peacock

    2009-12-01

    Full Text Available This article explores how the role of learning technologists, a professional group that has emerged during the last 15 to 20 years, may be diversifying to include supporting e-research. It contributes to the current debate about the emerging profession and the roles it should play in contemporary higher education. Previous studies have shown that, typically, the profession's role has focussed almost exclusively on curriculum development; traditionally, learning technologists work with students and tutors to enhance the learning environment with technology. This article presents two case studies of PhD research that used a standard e-learning tool, the virtual learning environment (VLE, to conduct focus groups online. The case studies demonstrate the expert role of the learning technologist in supporting researchers to make informed decisions about whether and how to use e-learning tools to conduct qualitative e-research. The learning technologist advised on the potential advantages and limitations of using the VLE for research and fostered collaborative, working relationships with the researchers, acquiring extensive background knowledge about their projects. This required the learning technologist to draw upon her own experience with research into e-learning and on her professional experience gained from supporting curriculum developments. It is suggested that many learning technologists could extend their roles, transferring their knowledge to include supporting e-research. A more inclusive model of the learning technologist's role in academia could help address the potential polarisation of the profession into researchers and practitioners.

  17. Supporting Quality Timely PhD Completions: Delivering Research Outcomes

    Science.gov (United States)

    Gasson, Susan

    2015-01-01

    The case study used a three-phase organising process to explain how design and implementation of an accessible and interactive electronic thesis submission form streamlined quality assurance of theses and their timely dissemination via an online thesis repository. The quality of the theses submitted is assured by key academics in their final sign…

  18. Institutional Support : Institute for Policy Analysis and Research ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    This grant from IDRC's Think Tank Initiative (TTI) will allow IPAR-Rwanda to strengthen its managerial and research capacity by means of a mentoring program for managers, researchers and support staff. This will include formulating a set of organizational goals and establishing a monitoring system to assess progress ...

  19. Institutional Support: Centre for Economic and Social Research ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    Institutional Support: Centre for Economic and Social Research, Education and Documentation (Burkina Faso). The Centre d'études de documentation et de ... innovations to improve lives and livelihoods. Five world-class research teams are working to develop vaccines for neglected livestock diseases in the Global South.

  20. Financial Support for Institutional Research, 1969-70.

    Science.gov (United States)

    Pieper, W. C., Jr.

    The Association for Institutional Research conducted a survey of all institutions of higher education in the U.S. and Canada in order to assess the number, size, and financial support of institutional research offices. Data were requested for the 1969-70 academic year. This report is based on the responses of 1,444 institutions that returned the…

  1. Support for biomedical research and its impact on radiology.

    Science.gov (United States)

    Bragg, D G; Hendee, W R

    1994-12-01

    Research in medical imaging has experienced substantial growth during the past decade. Still, research is a small fraction of the budget of the typical academic radiology program. Few radiology faculty participate in hypothesis-driven research projects. Funding of research will be more difficult to secure in the future, since clinical subsidies will diminish or disappear, support from industry is decreasing, and funds from private foundations and philanthropists are not likely to increase. Support from the NIH will probably remain about level in constant dollars. In response to these constraints, radiology will have to be both more creative and more opportunistic to tap the limited remaining resources of research support. An excellent compilation of some major resources was recently published by Williams and Holden (9). Efforts of the Conjoint Committee will continue to be critical for continuing support of the LDRR, encouraging the allocation of intramural and extramural resources of the NCI to medical imaging, guiding the development of the American Academy of Radiologic Research, providing research training opportunities for physicians and scientists in radiology, and leading the research effort in medical imaging in general (10). Within individual institutions and departments, imaging research must continue to be acknowledged as a priority despite increasing pressures to generate clinical revenue. Enhanced efforts are warranted to nurture the research interests of younger faculty and selected residents and fellows, including pairing them with research mentors and providing them with opportunities to develop skills in areas such as research design, statistical analysis, and evaluative techniques. The long-term well-being of radiology and its important contributions to patient care are dependent on its continued investment in research and development.

  2. A three-phase to three-phase series-resonant power converter with optimal input current waveforms, Part II: implementation and results

    NARCIS (Netherlands)

    Huisman, H.

    1988-01-01

    For pt.I see ibid., vol.35, no.2, p.263-8 (1988). A 15 kW three-phase prototype series-resonant power converter is constructed. The converter features sinusoidal output voltage and sinusoidal input currents. The control concepts and necessary electronics, as well as the layout of the power circuit,

  3. Building Support for Research Data Management: Biographies of Eight Research Universities

    Directory of Open Access Journals (Sweden)

    Katherine G. Akers

    2014-10-01

    Full Text Available Academic research libraries are quickly developing support for research data management (RDM, including both new services and infrastructure. Here, we tell the stories of how eight different universities have developed programs of RDM support, focusing on the prominent role of the library in educating and assisting researchers with managing their data throughout the research lifecycle. Based on these stories, we construct timelines for each university depicting key steps in building support for RDM, and we discuss similarities and dissimilarities among universities in motivation to provide RDM support, collaborations among campus units, assessment of needs and services, and changes in staffing.

  4. Public support for medical research in the 21st century.

    Science.gov (United States)

    Smith, P M

    2000-01-01

    Key public policies that have contributed to the rise of modern medical research in the 20th Century are reviewed, focusing especially on the United States and the post-World War II period. Drawing on this history, the question is posed: "Are these policies sufficient to insure vigorous medical research in the 21st Century?" Although radical policy changes are not needed, several proposals for policy and medical research portfolio redirection are offered, including a rebalancing of public supported research in all fields of science that contribute to medical advances. Medical research must also invest in a national and international information infrastructure that will allow the linking of researchers, clinical experimenters, practicing physicians, and the public in ways heretofore not imagined. Medical researchers must be leaders and advocates for the whole research enterprise in the 21st Century.

  5. Improving Support for America's Hidden Heroes: A Research Blueprint.

    Science.gov (United States)

    Terri, Tanielian; Kathryn E, Bouskill; Rajeev, Ramchand; Esther M, Friedman; Thomas E, Trail; Angela, Clague

    2018-01-01

    The United States is home to more than 21 million veterans, many of whom deployed to support combat operations around the globe during their military service and sustained service-related conditions or disabilities. Supporting these wounded, ill, and injured warriors once home are millions of informal caregivers-individuals who provide unpaid support with activities that enable the service member or veteran to live in a noninstitutionalized setting. In this study, researchers describe elements of a research blueprint to inform future efforts to improve support for military and veteran caregivers. To construct this blueprint, researchers inventoried currently available research on caregiving for disabled adults and children and gathered stakeholder input by conducting a survey and facilitating an online panel. The study highlights the need for more studies that examine how military and veteran caregiver needs evolve over time, how programs are working, and how caregiving affects specific subgroups. The resulting blueprint should serve as a guide for the caregiver support community to use in prioritizing and facilitating future research.

  6. Power Loss Calculation and Thermal Modelling for a Three Phase Inverter Drive System

    Directory of Open Access Journals (Sweden)

    Z. Zhou

    2005-12-01

    Full Text Available Power losses calculation and thermal modelling for a three-phase inverter power system is presented in this paper. Aiming a long real time thermal simulation, an accurate average power losses calculation based on PWM reconstruction technique is proposed. For carrying out the thermal simulation, a compact thermal model for a three-phase inverter power module is built. The thermal interference of adjacent heat sources is analysed using 3D thermal simulation. The proposed model can provide accurate power losses with a large simulation time-step and suitable for a long real time thermal simulation for a three phase inverter drive system for hybrid vehicle applications.

  7. Supporting research in area studies a guide for academic libraries

    CERN Document Server

    Pitman, Lesley

    2015-01-01

    Supporting Research in Area Studies: A Guide for Academic Libraries focuses on the study of other countries or regions of the world, crossing traditional disciplinary boundaries in the humanities and social sciences. The book provides a comprehensive guide for academic libraries supporting communities of researchers, exploring the specialist requirements of these researchers in information resources, resource discovery tools, information skills, and the challenges of working with materials in multiple languages. The book makes the case that adapting systems and procedures to meet these needs will help academic libraries be better placed to support their institutions' international agenda. Early chapters cover the academic landscape, its history, area studies, librarianship, and acquisitions. Subsequent chapters discuss collections management, digital products, and the digital humanities, and their role in academic projects, with final sections exploring information skills and the various disciplinary skills t...

  8. Data base development and research and editorial support

    Science.gov (United States)

    1988-01-01

    The Life Sciences Bibliographic Data Base was created in 1981 and subsequently expanded. A systematic, professional system was developed to collect, organize, and disseminate information about scientific publications resulting from research. The data base consists of bibliographic information and hard copies of all research papers published by Life Sciences-supported investigators. Technical improvements were instituted in the database. To minimize costs, take advantage of advances in personal computer technology, and achieve maximum flexibility and control, the data base was transferred from the JSC computer to personal computers at George Washington University (GWU). GWU also performed a range of related activities such as conducting in-depth searches on a variety of subjects, retrieving scientific literature, preparing presentations, summarizing research progress, answering correspondence requiring reference support, and providing writing and editorial support.

  9. NRC safety research in support of regulation, 1986

    International Nuclear Information System (INIS)

    1987-09-01

    This report is the second in a series of annual reports responding to congressional inquiries as to the utilization of nuclear regulatory research. NUREG-1175, ''NRC Safety Research in Support of Regulation,'' published in May 1986, reported major research accomplishments between about FY 1980 and FY 1985. This report narrates the accomplishments of FY 1986 and does not restate earlier accomplishments. Earlier research results are mentioned in the context of current results in the interest of continuity. Both the direct contributions to scientific and technical knowledge and their regulatory applications, when there has been a definite regulatory outcome during FY 1986, have been described

  10. Collaborating With Businesses to Support and Sustain Research.

    Science.gov (United States)

    Moch, Susan Diemert; Jansen, Debra A; Jadack, Rosemary A; Page, Phil; Topp, Robert

    2015-10-01

    Financial assistance is necessary for sustaining research at universities. Business collaborations are a potential means for obtaining these funds. To secure funding, understanding the process for obtaining these business funds is important for nursing faculty members. Although faculty rarely request funding from businesses, they are often in a position to solicit financial support due to existing relationships with clinical agency administrators, staff, and community leaders. The economic support received from businesses provides outcomes in nursing research, research education, academic-service partnerships, and client health care. This article describes the steps and processes involved in successfully obtaining research funding from businesses. In addition, case examples for securing and maintaining funding from health care agencies (evidence-based practice services) and from a health manufacturing company (product evaluation) are used to demonstrate the process. © The Author(s) 2015.

  11. Modeling and Analysis of a Three-Phase Solid-State Var ...

    African Journals Online (AJOL)

    Modeling and Analysis of a Three-Phase Solid-State Var Compensator (SSVC) ... Nigerian Journal of Technology. Journal Home ... The problems associated with the flow of reactive power in transmission and distribution lines are well known.

  12. High performance predictive current control of a three phase VSI: An ...

    Indian Academy of Sciences (India)

    ... current control of a three phase VSI: An experimental assessment ... Voltage source inverter; two level inverter; predictive current control; weighting factor ... Conventionally, for reference current tracking control in a two level VSI, the objective ...

  13. Novel, Four-Switch, Z-Source Three-Phase Inverter

    DEFF Research Database (Denmark)

    Antal, Robert; Muntean, Nicolae; Boldea, Ion

    2010-01-01

    This paper presents a new z-source three phase inverter topology. The proposed topology combines the advantages of a traditional four-switch three-phase inverter with the advantages of the z impedance network (one front-end diode, two inductors and two X connected capacitors). This new topology......, besides the self-boost property, has low switch count and it can operate as a buck-boost inverter. In contrast to standard four-switch three-phase inverter which operates at half dc input voltage the proposed four-switch z-source inverter, by self boosting, brings the output voltage at same (or higher......) value as in six switch standard three-phase inverter. The article presents the derivation of the equations describing the operation of the converter based on space vector analysis, validation through digital simulations in PSIM and preliminary experimental results on a laboratory setup with a dsPIC30F...

  14. Design of three-phased SPWM based on AT89C52

    Science.gov (United States)

    Wu, Xiaorui

    2018-05-01

    According to the AT89C52 and the area equivalent principle, a three phase SPWM algorithm based on the 8 bit single chip is obtained. Through computer programming, three-phase SPWM wave generated by a single chip microcomputer is applied to the circuit of the static reactive power generator. The result shows that this method is feasible and can reduce the cost of SVG.

  15. MODELING OF SYMMETRIC THREE-PHASE ASYNCHRONOUS ELECTRIC MOTOR IN ASYMMETRIC CONNECTION TO NETWORK

    Directory of Open Access Journals (Sweden)

    V. I. Lukovnikov

    2005-01-01

    Full Text Available The paper shows how to solve the problem concerning reveal of changes in mathematical models and electric parameters of symmetric three-phase short-circuited asynchronous electric motors in case of their connection to single- or two-phase network in comparison with their connection to three-phase network. The uniform methodological approach permitting to generalize the known data and receive new results is offered in the paper.

  16. Three-phase double-arc plasma for spectrochemical analysis of environmental samples.

    Science.gov (United States)

    Mohamed, M M; Ghatass, Z F; Shalaby, E A; Kotb, M M; El-Raey, M

    2000-12-01

    A new instrument, which uses a three-phase current to support a double-arc argon plasma torch for evaporation, atomization and excitation of solid or powder samples, is described. The sampling arc is ignited between the first and second electrode while the excitation arc is ignited between the second and third electrode. Aerosol generated from the sample (first electrode) is swept by argon gas, through a hole in the second electrode (carbon tubing electrode), into the excitation plasma. A tangential stream of argon gas is introduced through an inlet orifice as a coolant gas for the second electrode. This gas stream forces the excitation arc discharge to rotate reproducibly around the electrode surface. Discharge rotation increases the stability of the excitation plasma. Spectroscopic measurements are made directly in the current-carrying region of the excitation arc. An evaluation of each parameter influencing the device performance was performed. Analytical calibration curves were obtained for Fe, Al, K, and Pb. Finally, the present technique was applied for the analysis of environmental samples. The present method appears to have significant, low cost analytical utility for environmental measurements.

  17. A New Topology for Interline Dynamic Voltage Restorer Based on Direct Three-Phase Converter

    Directory of Open Access Journals (Sweden)

    E. Babaei

    2016-03-01

    Full Text Available In this paper, a new topology for Interline Dynamic Voltage Restorer (IDVR is proposed. This topology contains two direct three-phase converters which have been connected together by a common fictitious dc-link. According to the kind of the disturbances, both of the converters can be employed as a rectifier or inverter. The converters receive the required compensation energy from the gird through the direct link which is provided by the dual-proposed switches. Due to the lack of the huge storage elements, the practical prototype of the proposed topology is more economical in comparison with the traditional structure. Moreover, compensating for long time duration is possible due to the unlimited eternal energy which is provided from the grids. The low volume, cost and weight are the additional features of the proposed topology in comparison with traditional types. This topology is capable to compensate both of the balanced and unbalanced disturbances. Furthermore, restoring the deep sags and power outages will be possible with the support from the other grid. Unlike the conventional topologies, the capability of compensation is independent from the power flow and the power factor of each grid. The performance of the proposed IDVR topology is validated by computer simulation with PSCAD/EMTDC software.

  18. The analysis of magnesium oxide hydration in three-phase reaction system

    Energy Technology Data Exchange (ETDEWEB)

    Tang, Xiaojia; Guo, Lin; Chen, Chen; Liu, Quan; Li, Tie; Zhu, Yimin, E-mail: ntp@dlmu.edu.cn

    2014-05-01

    In order to investigate the magnesium oxide hydration process in gas–liquid–solid (three-phase) reaction system, magnesium hydroxide was prepared by magnesium oxide hydration in liquid–solid (two-phase) and three-phase reaction systems. A semi-empirical model and the classical shrinking core model were used to fit the experimental data. The fitting result shows that both models describe well the hydration process of three-phase system, while only the semi-empirical model right for the hydration process of two-phase system. The characterization of the hydration product using X-Ray diffraction (XRD) and scanning electron microscope (SEM) was performed. The XRD and SEM show hydration process in the two-phase system follows common dissolution/precipitation mechanism. While in the three-phase system, the hydration process undergo MgO dissolution, Mg(OH){sub 2} precipitation, Mg(OH){sub 2} peeling off from MgO particle and leaving behind fresh MgO surface. - Graphical abstract: There was existence of a peeling-off process in the gas–liquid–solid (three-phase) MgO hydration system. - Highlights: • Magnesium oxide hydration in gas–liquid–solid system was investigated. • The experimental data in three-phase system could be fitted well by two models. • The morphology analysis suggested that there was existence of a peel-off process.

  19. Single phase inverter for a three phase power generation and distribution system

    Science.gov (United States)

    Lindena, S. J.

    1976-01-01

    A breadboard design of a single-phase inverter with sinusoidal output voltage for a three-phase power generation and distribution system was developed. The three-phase system consists of three single-phase inverters, whose output voltages are connected in a delta configuration. Upon failure of one inverter the two remaining inverters will continue to deliver three-phase power. Parallel redundancy as offered by two three-phase inverters is substituted by one three-phase inverter assembly with high savings in volume, weight, components count and complexity, and a considerable increase in reliability. The following requirements must be met: (1) Each single-phase, current-fed inverter must be capable of being synchronized to a three-phase reference system such that its output voltage remains phaselocked to its respective reference voltage. (2) Each single-phase, current-fed inverter must be capable of accepting leading and lagging power factors over a range from -0.7 through 1 to +0.7.

  20. How Solar Resource Data supports Research and Development

    OpenAIRE

    Kern, Jürgen

    2013-01-01

    The presentation describes the methods of renewable resource data, how the research and development will benefits from Renewable Resource Atlas and how institutions will leverage the solar monitoring station data to support renewable energy project deployment in other locations throughout the Kingdom.

  1. Canadian safeguards research and development in support of the IAEA

    International Nuclear Information System (INIS)

    1980-03-01

    Canada has established a safeguards research and development program whose purpose is to supplement the resources of the IAEA. The program of support is a coordinated effort for the development and application of safeguards techniques and instruments to reactors of Canadian design. This document sets forth those tasks that make up the program

  2. The Support-Stress Paradigm and Faculty Research Publication.

    Science.gov (United States)

    Neumann, Yorem; Finaly-Neumann, Edith

    1990-01-01

    A study developed and tested a model that examines the relative powers of support and work stress indicators in explaining faculty research productivity. Empirical examination indicates the model is most influential in physics, least in education, and that different indicators are significant in determining publication in hard and soft sciences.…

  3. USDA Research in Support of Deployed Military Troops

    Science.gov (United States)

    The US Department of Agriculture has a long history of collaborating with the US military to conduct research in support of war efforts. The predecessor laboratory of the current USDA-ARS Center for Medical, Agricultural and Veterinary Entomology (CMAVE) located in Gainesville, Florida has a history...

  4. Evolution of Decision Support Systems Research Field in Numbers

    Directory of Open Access Journals (Sweden)

    Ana-Maria SUDUC

    2010-01-01

    Full Text Available The scientific production in a certain field shows, in great extent, the research interests in that field. Decision Support Systems are a particular class of information systems which are gaining more popularity in various domains. In order to identify the evolution in time of the publications number, authors, subjects, publications in the Decision Support Systems (DSS field, and therefore the scientific world interest for this field, in November 2010 there have been organized a series of queries on three major international scientific databases: ScienceDirect, IEEE Xplore Digital Library and ACM Digital Library. The results presented in this paper shows that, even the decision support systems research field started in 1960s, the interests for this type of systems grew exponentially with each year in the last decades.

  5. The Atomic Energy Control Board's regulatory research and support program

    International Nuclear Information System (INIS)

    1988-04-01

    The purpose of the Regulatory Research and Support Program is to augment and extend the capability of the Atomic Energy Control Board's (AECB) regulatory program beyond the capability of in-house resources. The overall objective of the program is to produce pertinent and independent scientific and other knowledge and expertise that will assist the AECB in making correct, timely and credible decisions on regulating the development, application and use of atomic energy. The objectives are achieved through contracted research, development, studies, consultant and other kinds of projects administered by the Research and Radiation Protection Branch (RRB) of the AECB

  6. Governmental Research Support Programs and Private Entities in Slovakia

    Directory of Open Access Journals (Sweden)

    Maliková Zuzana

    2015-01-01

    Full Text Available The paper analyses public subsidies aimed to enhance development and innovation in the Slovakian private sector. The paper reviews theoretical approaches of the necessity of public support to research and development activities in order to increase private investment in research and development. An overview of research and development support tools in Slovakia is presented. The analytical part of the work is oriented on a comparative analysis of two granting agencies in Slovakia [Agency for Research and Development (ARD and Agency of Operational Program Research and Development (OPRD]. Special attention is given to direct public financial support. Logit analysis showed a relationship between success of grant applicants and their characteristics. We find that the following have impact on success of the application: Age of the company, amount of the grant required, legal form of the company, and the agency to which the application for grant was submitted. Applicants with legal form Ltd. (limited liability company have a higher chance of receiving grant than other legal forms. The highest chance of success has a request for a grant of up to 500.000 €. According to the results of our analysis, the chance to obtain a grant decreases with each passing year.

  7. Decision Support Systems for Research and Management in Advanced Life Support

    Science.gov (United States)

    Rodriquez, Luis F.

    2004-01-01

    Decision support systems have been implemented in many applications including strategic planning for battlefield scenarios, corporate decision making for business planning, production planning and control systems, and recommendation generators like those on Amazon.com(Registered TradeMark). Such tools are reviewed for developing a similar tool for NASA's ALS Program. DSS are considered concurrently with the development of the OPIS system, a database designed for chronicling of research and development in ALS. By utilizing the OPIS database, it is anticipated that decision support can be provided to increase the quality of decisions by ALS managers and researchers.

  8. United States Domestic Research Reactor Infrastructure TRIGA Reactor Fuel Support

    International Nuclear Information System (INIS)

    Morrell, Douglas

    2011-01-01

    The United State Domestic Research Reactor Infrastructure Program at the Idaho National Laboratory manages and provides project management, technical, quality engineering, quality inspection and nuclear material support for the United States Department of Energy sponsored University Reactor Fuels Program. This program provides fresh, unirradiated nuclear fuel to Domestic University Research Reactor Facilities and is responsible for the return of the DOE-owned, irradiated nuclear fuel over the life of the program. This presentation will introduce the program management team, the universities supported by the program, the status of the program and focus on the return process of irradiated nuclear fuel for long term storage at DOE managed receipt facilities. It will include lessons learned from research reactor facilities that have successfully shipped spent fuel elements to DOE receipt facilities.

  9. Research priorities on ending child marriage and supporting married girls.

    Science.gov (United States)

    Svanemyr, Joar; Chandra-Mouli, Venkatraman; Raj, Anita; Travers, Ellen; Sundaram, Lakshmi

    2015-09-03

    Over the past few years the issue of child marriage has received growing political and programmatic attention. In spite of some progress in a number of countries, global rates have not declined over the past decade. Knowledge gaps remain in understanding trends, drivers and approaches to ending child marriage, especially to understand what is needed to achieve results on a large scale. This commentary summarizes the outcomes of an Expert Group Meeting organized by World Health Organization to discuss research priorities on Ending Child Marriage and Supporting Married Girls. It presents research gaps and recommends priorities for research in five key areas; (i) prevalence and trends of child marriage; (ii) causes of child marriage (iii) consequences of child marriage; (iv) efforts to prevent child marriage; (v) efforts to support married girls.

  10. Creating and supporting a mixed methods health services research team.

    Science.gov (United States)

    Bowers, Barbara; Cohen, Lauren W; Elliot, Amy E; Grabowski, David C; Fishman, Nancy W; Sharkey, Siobhan S; Zimmerman, Sheryl; Horn, Susan D; Kemper, Peter

    2013-12-01

    To use the experience from a health services research evaluation to provide guidance in team development for mixed methods research. The Research Initiative Valuing Eldercare (THRIVE) team was organized by the Robert Wood Johnson Foundation to evaluate The Green House nursing home culture change program. This article describes the development of the research team and provides insights into how funders might engage with mixed methods research teams to maximize the value of the team. Like many mixed methods collaborations, the THRIVE team consisted of researchers from diverse disciplines, embracing diverse methodologies, and operating under a framework of nonhierarchical, shared leadership that required new collaborations, engagement, and commitment in the context of finite resources. Strategies to overcome these potential obstacles and achieve success included implementation of a Coordinating Center, dedicated time for planning and collaborating across researchers and methodologies, funded support for in-person meetings, and creative optimization of resources. Challenges are inevitably present in the formation and operation of effective mixed methods research teams. However, funders and research teams can implement strategies to promote success. © Health Research and Educational Trust.

  11. An interoperable research data infrastructure to support climate service development

    Science.gov (United States)

    De Filippis, Tiziana; Rocchi, Leandro; Rapisardi, Elena

    2018-02-01

    Accessibility, availability, re-use and re-distribution of scientific data are prerequisites to build climate services across Europe. From this perspective the Institute of Biometeorology of the National Research Council (IBIMET-CNR), aiming at contributing to the sharing and integration of research data, has developed a research data infrastructure to support the scientific activities conducted in several national and international research projects. The proposed architecture uses open-source tools to ensure sustainability in the development and deployment of Web applications with geographic features and data analysis functionalities. The spatial data infrastructure components are organized in typical client-server architecture and interact from the data provider download data process to representation of the results to end users. The availability of structured raw data as customized information paves the way for building climate service purveyors to support adaptation, mitigation and risk management at different scales.This work is a bottom-up collaborative initiative between different IBIMET-CNR research units (e.g. geomatics and information and communication technology - ICT; agricultural sustainability; international cooperation in least developed countries - LDCs) that embrace the same approach for sharing and re-use of research data and informatics solutions based on co-design, co-development and co-evaluation among different actors to support the production and application of climate services. During the development phase of Web applications, different users (internal and external) were involved in the whole process so as to better define user needs and suggest the implementation of specific custom functionalities. Indeed, the services are addressed to researchers, academics, public institutions and agencies - practitioners who can access data and findings from recent research in the field of applied meteorology and climatology.

  12. An interoperable research data infrastructure to support climate service development

    Directory of Open Access Journals (Sweden)

    T. De Filippis

    2018-02-01

    Full Text Available Accessibility, availability, re-use and re-distribution of scientific data are prerequisites to build climate services across Europe. From this perspective the Institute of Biometeorology of the National Research Council (IBIMET-CNR, aiming at contributing to the sharing and integration of research data, has developed a research data infrastructure to support the scientific activities conducted in several national and international research projects. The proposed architecture uses open-source tools to ensure sustainability in the development and deployment of Web applications with geographic features and data analysis functionalities. The spatial data infrastructure components are organized in typical client–server architecture and interact from the data provider download data process to representation of the results to end users. The availability of structured raw data as customized information paves the way for building climate service purveyors to support adaptation, mitigation and risk management at different scales.This work is a bottom-up collaborative initiative between different IBIMET-CNR research units (e.g. geomatics and information and communication technology – ICT; agricultural sustainability; international cooperation in least developed countries – LDCs that embrace the same approach for sharing and re-use of research data and informatics solutions based on co-design, co-development and co-evaluation among different actors to support the production and application of climate services. During the development phase of Web applications, different users (internal and external were involved in the whole process so as to better define user needs and suggest the implementation of specific custom functionalities. Indeed, the services are addressed to researchers, academics, public institutions and agencies – practitioners who can access data and findings from recent research in the field of applied meteorology and climatology.

  13. Control method of Three-phase Four-leg converter based on repetitive control

    Science.gov (United States)

    Hui, Wang

    2018-03-01

    The research chose the magnetic levitation force of wind power generation system as the object. In order to improve the power quality problem caused by unbalanced load in power supply system, we combined the characteristics and repetitive control principle of magnetic levitation wind power generation system, and then an independent control strategy for three-phase four-leg converter was proposed. In this paper, based on the symmetric component method, the second order generalized integrator was used to generate the positive and negative sequence of signals, and the decoupling control was carried out under the synchronous rotating reference frame, in which the positive and negative sequence voltage is PI double closed loop, and a PI regulator with repetitive control was introduced to eliminate the static error regarding the fundamental frequency fluctuation characteristic of zero sequence component. The simulation results based on Matlab/Simulink show that the proposed control project can effectively suppress the disturbance caused by unbalanced loads and maintain the load voltage balance. The project is easy to be achieved and remarkably improves the quality of the independent power supply system.

  14. ADVANCED DIAGNOSTIC TECHNIQUES FOR THREE-PHASE SLURRY BUBBLE COLUMN REACTORS(SBCR)

    Energy Technology Data Exchange (ETDEWEB)

    M.H. Al-Dahhan; L.S. Fan; M.P. Dudukovic

    2002-07-25

    This report summarizes the accomplishment made during the third year of this cooperative research effort between Washington University, Ohio State University and Air Products and Chemicals. Data processing of the performed Computer Automated Radioactive Particle Tracking (CARPT) experiments in 6 inch column using air-water-glass beads (150 {micro}m) system has been completed. Experimental investigation of time averaged three phases distribution in air-Therminol LT-glass beads (150 {micro}m) system in 6 inch column has been executed. Data processing and analysis of all the performed Computed Tomography (CT) experiments have been completed, using the newly proposed CT/Overall gas holdup methodology. The hydrodynamics of air-Norpar 15-glass beads (150 {micro}m) have been investigated in 2 inch slurry bubble column using Dynamic Gas Disengagement (DGD), Pressure Drop fluctuations, and Fiber Optic Probe. To improve the design and scale-up of bubble column reactors, a correlation for overall gas holdup has been proposed based on Artificial Neural Network and Dimensional Analysis.

  15. Electrochemistry of immobilized particles and droplets experiments with three-phase electrodes

    CERN Document Server

    Scholz, Fritz; Gulaboski, Rubin; Schröder, Uwe

    2014-01-01

    This second edition of a successful and highly-accessed monograph has been extended by more than 100 pages. It includes an enlarged coverage of applications for materials characterization and analysis. Also a more detailed description of strategies for determining free energies of ion transfer between miscible liquids is provided. This is now possible with a "third-phase strategy" which the authors explain from theoretical and practical points of view. The book is still the only one detailing strategies for solid state electroanalysis. It also features the specific potential of the techniques to use immobilized particles (for studies of solid materials) and of immobilized droplets of immiscible liquids for the purpose of studying the three-phase electrochemistry of these liquids. This also includes studies of ion transfer between aqueous and immiscible non-aqueous liquids. The bibliography of all published papers in this field of research has been expanded from 318 to now 444 references in this second editi...

  16. Research on operation support system for nuclear power plants

    International Nuclear Information System (INIS)

    Wakabayashi, Jiro

    1989-01-01

    Nuclear power plants are the typical, complex, large scale engineering system, and at the time of accidents, there is the possibility to extend disasters to wide range beyond borders, therefore, it is the feature that the requirement for their reliability and safety is much severe as compared with other engineering systems. The fact that human errors become the major cause of large accidents is in common in large scale engineering systems, and the development of the operation support system for preventing it has become an important research subject. Also the research on design support system and maintenance support system is in progress to prevent human errors. Operation support system is composed of diagnostic system, operation guide system, man-machine interface and knowledge data base, and throughout these, the research on the human errors arising in the process of human decision making becomes the basis. Rasmussen's model for decision making, the classification of human errors and the reliability analysis for men, the factors affecting human errors, the acquisition of knowledge, the compilation and management of knowledge data base, the diagnostic system, operation guide system and man-machine interface are described. (K.I.)

  17. Research and technology programmes supporting waste management in BNFL

    International Nuclear Information System (INIS)

    Fairhall, G.A.; Horner, A.M.

    2000-01-01

    Waste Management is a major activity of BNFL in the UK and at various locations internationally. To support these activities extensive programmes of Research and Technology have been undertaken for many years. This involves practical studies involving active and non-active work at laboratory and pilot plant scale. Extensive use is also made of theoretical and modelling techniques. Current work is aimed at underpinning and improving current operations supporting the design and safety cases of new plant and addressing waste management activities of the future including decommissioning. (authors)

  18. A new method for the experimental determination of three-phase relative permeabilities

    International Nuclear Information System (INIS)

    Perez Carrillo, Edgar Ricardo; Jose Francisco Zapata Arango; Santos Santos, Nicolas

    2008-01-01

    Petroleum reservoirs under primary, secondary or tertiary recovery processes usually experience simultaneous flow of three fluids phases (oil, water and gas). Reports on some mathematical models for calculating three-phase relative permeability are available in the Literature. Nevertheless, many of these models were designed based on certain experimental conditions and reservoir rocks and fluids. Therefore, special care has to be taken when applying them to specific reservoirs. At the laboratory level, three-phase relative permeability can be calculated using experimental unsteady-state or steady state methodologies. This paper proposes an unsteady-state methodology to evaluate three-phase relative permeability using the equipment available at the petrophysical analysis Laboratory of the Instituto Colombiano del Petroleo (ICP) of Ecopetrol S.A. Improvements to the equipment were effected in order to achieve accuracy in the unsteady-state measurement of three-phase relative permeability. The target of improvements was directed toward to the attainment of two objectives:1) the modification of the equipment to obtain more reliable experimental data and 2) the appropriate interpretation of the data obtained. Special attention was given to the differential pressure and uncertainty measurement in the determination of fluid saturation in the rock samples. Three experiments for three-phase relative permeability were conducted using a sample A and reservoir rock from the Colombian Foothills. Fluid tests included the utilization of synthetic brine, mineral oil, reservoir crude oil and nitrogen. Two runs were conducted at the laboratory conditions while one run was conducted at reservoir conditions. Experimental results of these tests were compared using 16 mathematical models of three-phase relative permeability. For the three-phase relative permeability to oil, the best correlations between experimental data and tests using Blunt, Hustad Hasen, and Baker's models were

  19. A Physical Model for Three-Phase Compaction in Silicic Magma Reservoirs

    Science.gov (United States)

    Huber, Christian; Parmigiani, Andrea

    2018-04-01

    We develop a model for phase separation in magma reservoirs containing a mixture of silicate melt, crystals, and fluids (exsolved volatiles). The interplay between the three phases controls the dynamics of phase separation and consequently the chemical and physical evolution of magma reservoirs. The model we propose is based on the two-phase damage theory approach of Bercovici et al. (2001, https://doi.org/10.1029/2000JB900430) and Bercovici and Ricard (2003, https://doi.org/10.1046/j.1365-246X.2003.01854.x) because it offers the leverage of considering interface (in the macroscopic limit) between phases that can deform depending on the mechanical work and phase changes taking place locally in the magma. Damage models also offer the advantage that pressure is defined uniquely to each phase and does not need to be equal among phases, which will enable us to consider, in future studies, the large capillary pressure at which fluids are mobilized in mature, crystal-rich, magma bodies. In this first analysis of three-phase compaction, we solve the three-phase compaction equations numerically for a simple 1-D problem where we focus on the effect of fluids on the efficiency of melt-crystal separation considering the competition between viscous and buoyancy stresses only. We contrast three sets of simulations to explore the behavior of three-phase compaction, a melt-crystal reference compaction scenario (two-phase compaction), a three-phase scenario without phase changes, and finally a three-phase scenario with a parameterized second boiling (crystallization-induced exsolution). The simulations show a dramatic difference between two-phase (melt crystals) and three-phase (melt-crystals-exsolved volatiles) compaction-driven phase separation. We find that the presence of a lighter, significantly less viscous fluid hinders melt-crystal separation.

  20. Research Managers at Jamaica's National University Are Strategically Deploying a Modest Research Development Fund in Support of Impactful Research

    Science.gov (United States)

    Ivey, Paul W.; Henry, Martin

    2016-01-01

    The purpose of this paper is to highlight, using examples, how the University of Technology, Jamaica (UTech, Jamaica) is strategically using a modest internal research development fund, which is managed by the research managers in its research and innovation management office, to support impactful research projects. Critical reflection and the…

  1. NRC safety research in support of regulation, FY 1991

    International Nuclear Information System (INIS)

    1992-04-01

    This report, the seventh in a series of annual reports, was prepared in response to congressional inquiries concerning how nuclear regulatory research is used. It summarizes the accomplishments of the Office of Nuclear Regulatory Research during FY 1991. The goal of this office is to ensure that safety-related research provides the technical bases for rulemaking and for related decisions in support of NRC licensing and inspection activities. This research is necessary to make certain that the regulations that are imposed on licensees provide an adequate margin of safety so as to protect the health and safety of the public. This report describes both the direct contributions to scientific and technical knowledge with regard to nuclear safety and their regulatory applications

  2. NRC safety research in support of regulation, FY 1990

    International Nuclear Information System (INIS)

    1991-04-01

    This report, the sixth in a series of annual reports, was prepared in response to congressional inquiries concerning how nuclear regulatory research is used. It summarizes the accomplishments of the Office of Nuclear Regulatory Research during FY 1990. The goal of this office is to ensure that safety-related research provides the technical bases for rulemaking and for related decisions in support of NRC licensing and inspection activities. This research is necessary to make certain that the regulations that are imposed on licensees provide an adequate margin of safety so as to protect the health and safety of the public. This report describes both the direct contributions to scientific and technical knowledge with regard to nuclear safety and their regulatory applications

  3. NRC safety research in support of regulation--FY 1989

    International Nuclear Information System (INIS)

    1990-04-01

    This report, the fifth in a series of annual reports, was prepared in response to congressional inquiries concerning how nuclear regulatory research is used. It summarizes the accomplishments of the Office of Nuclear Regulatory Research during FY 1989. The goal of this office is to ensure that safety-related research provides the technical bases for rulemaking and for related decisions in support of NRC licensing and inspection activities. This research is necessary to make certain that the regulations that are imposed on licensees provide an adequate margin of safety so as to protect the health and safety of the public. This report describes both the direct contributions to scientific and technical knowledge with regard to nuclear safety and their regulatory applications

  4. NRC safety research in support of regulation, 1988

    International Nuclear Information System (INIS)

    1989-05-01

    This report, the fourth in a series of annual reports, was prepared in response to Congressional inquiries concerning how nuclear regulatory research is used. It summarizes the accomplishments of the Office of Nuclear Regulatory Research during 1988. The goal of this office is to ensure that safety-related research provides the technical bases for rulemaking and for related decisions in support of NRC licensing and inspection activities. This research is necessary to make certain that the regulations that are imposed on licensees provide an adequate margin of safety so as to protect the health and safety of the public. This report describes both the direct contributions to scientific and technical knowledge with regard to nuclear safety and their regulatory applications

  5. The comparing results of carcinoma between three-phase and delayed whole body bone scan

    International Nuclear Information System (INIS)

    Si Hongwei; Li Xianfeng

    2004-01-01

    Purpose: Three phase bone scan is an imaging technology in nuclear medicine, which composed of blood flow phase, blood pool phase and delayed phase and the last one is often performed in routine works in department of nuclear medicine. The purpose of this study is to evaluate the merit of three-phase bone scan.Methods: In this study, we chose 54 patients who were having an regional pain which caused by benign or malignant carcinoma that diagnosed by CT, X-ray, ECT, MRI or other examinations. The imaging were acquired simultaneously from both anterior and posterior views, after a bolus injection of 1110 MBq technetium-99m-labelled methylene diphosphonate (MDP), blood phase contains 20 frame sand 3 seconds per frame, blood pool phase contains 5 frames and 1 minute per frame, delayed phase was performed 2.5 hour later. According to the results of three-phase bone scan, the patients were divided into 2 groups: normal and abnormal groups. The abnormal group includes early phase positive,delay positive and all three phase positive sets. The comparing among the 3 sets were analyzed by chi-square test and other statistic means.Results: There were 54 patients who had suffered lung cancer, breast cancer and other cancer,involved in this study, 34 males and 20 females, ranged age 17 to 88 years, were normal in 15 cases,positive in 22 cases, the results in delayed phase were positive in 9 cases, blood flow and blood pool phase showed blood flow changes in 4 cases and soft tissue tumors were seen in 4 cases. Three phase bone scan was more sensitive than delayed whole body bone scan in detecting the abnormal sites (p 0.05) The sensitivity of detecting tumors in blood flow and blood pool phase,delayed phase were respectively lower than in three phase bone scan (p<0.001).Conclusion: It is more sensitivity of detecting tumor lesions in three phase bone scan than in delayed phase whole body bone scan and the changes of blood flow and soft tissue can be seen in three phase bone scan

  6. Computational Science Research in Support of Petascale Electromagnetic Modeling

    International Nuclear Information System (INIS)

    Lee, L.-Q.

    2008-01-01

    Computational science research components were vital parts of the SciDAC-1 accelerator project and are continuing to play a critical role in newly-funded SciDAC-2 accelerator project, the Community Petascale Project for Accelerator Science and Simulation (ComPASS). Recent advances and achievements in the area of computational science research in support of petascale electromagnetic modeling for accelerator design analysis are presented, which include shape determination of superconducting RF cavities, mesh-based multilevel preconditioner in solving highly-indefinite linear systems, moving window using h- or p- refinement for time-domain short-range wakefield calculations, and improved scalable application I/O

  7. Supporting capacity for research on malaria in Africa

    DEFF Research Database (Denmark)

    Greenwood, Brian; Gaye, Oumar; Kamya, Moses R

    2018-01-01

    Substantial progress has been made in the control of malaria in Africa but much remains to be done before malaria elimination on the continent can be achieved. Further progress can be made by enhancing uptake of existing control tools but, in high transmission areas, additional tools will be needed....... Development and evaluation of these new tools will require a substantial cadre of African scientists well trained in many different disciplines. This paper describes the activities undertaken by the Malaria Capacity Development Consortium (MCDC) to support the careers of PhD students and postdoctoral fellows...... undertaking research on malaria at five African universities. A systematic assessment of constraints on PhD training and research support systems was undertaken at each partner African university at the beginning of the programme and many of these constraints were remedied. The success of the programme...

  8. Research Support Facility (RSF): Leadership in Building Performance (Brochure)

    Energy Technology Data Exchange (ETDEWEB)

    2011-09-01

    This brochure/poster provides information on the features of the Research Support Facility including a detailed illustration of the facility with call outs of energy efficiency and renewable energy technologies. Imagine an office building so energy efficient that its occupants consume only the amount of energy generated by renewable power on the building site. The building, the Research Support Facility (RSF) occupied by the U.S. Department of Energy's National Renewable Energy Laboratory (NREL) employees, uses 50% less energy than if it were built to current commercial code and achieves the U.S. Green Building Council's Leadership in Energy and Environmental Design (LEED{reg_sign}) Platinum rating. With 19% of the primary energy in the U.S. consumed by commercial buildings, the RSF is changing the way commercial office buildings are designed and built.

  9. Crowdfunding To Support University Research and Public Outreach

    Science.gov (United States)

    Jackson, Brian

    2016-10-01

    Crowdfunding involves raising (usually small) monetary contributions from a large number of people, often performed via the internet. Several universities have adopted this model to support small-dollar, high-profile projects and provide the seed money for research efforts. By contrast with traditional scientific funding, crowdfunding provides a novel way to engage the public in the scientific process and sometimes involves donor rewards in the form of acknowledgments in publications and direct involvement in the research itself.In addition to Kickstarter.com and Indiegogo.com that support a range of enterprises, there are several organizations tailored to scientific research and development, including Experiment.com and the now-defunct PetriDish.org. Private companies are also available to help universities establish their own crowd-funding platforms. At Boise State University, we recently engaged the services of ScaleFunder to launch the PonyUp platform (https://ponyup.boisestate.edu/), inaugurated in Fall 2015 with requests of support for projects ranging from the health effects of organic food during pregnancy to censuses of hummingbirds.In this presentation, I'll discuss my own crowdfunding project to support the rehabilitation of Boise State's on-campus observatory. As the first project launched on PonyUp, it was an enormous success -- we met our original donation goal of $8k just two weeks into the four-week campaign and so upped the goal to $10k, which we achieved two weeks later. In addition to the very gratifying monetary support of the broader Boise community, we received personal stories from many of our donors about their connections to Boise State and the observatory. I'll talk about our approach to social and traditional media platforms and discuss how we leveraged an unlikely cosmic syzygy to boost the campaign.

  10. Fuzzy Logic Controlled Solar Module for Driving Three- Phase Induction Motor

    Science.gov (United States)

    Afiqah Zainal, Nurul; Sooi Tat, Chan; Ajisman

    2016-02-01

    Renewable energy produced by solar module gives advantages for generated three- phase induction motor in remote area. But, solar module's ou tput is uncertain and complex. Fuzzy logic controller is one of controllers that can handle non-linear system and maximum power of solar module. Fuzzy logic controller used for Maximum Power Point Tracking (MPPT) technique to control Pulse-Width Modulation (PWM) for switching power electronics circuit. DC-DC boost converter used to boost up photovoltaic voltage to desired output and supply voltage source inverter which controlled by three-phase PWM generated by microcontroller. IGBT switched Voltage source inverter (VSI) produced alternating current (AC) voltage from direct current (DC) source to control speed of three-phase induction motor from boost converter output. Results showed that, the output power of solar module is optimized and controlled by using fuzzy logic controller. Besides that, the three-phase induction motor can be drive and control using VSI switching by the PWM signal generated by the fuzzy logic controller. This concluded that the non-linear system can be controlled and used in driving three-phase induction motor.

  11. Fuzzy Logic Controlled Solar Module for Driving Three- Phase Induction Motor

    International Nuclear Information System (INIS)

    Zainal, Nurul Afiqah; Tat, Chan Sooi; Ajisman

    2016-01-01

    Renewable energy produced by solar module gives advantages for generated three- phase induction motor in remote area. But, solar module's output is uncertain and complex. Fuzzy logic controller is one of controllers that can handle non-linear system and maximum power of solar module. Fuzzy logic controller used for Maximum Power Point Tracking (MPPT) technique to control Pulse-Width Modulation (PWM) for switching power electronics circuit. DC-DC boost converter used to boost up photovoltaic voltage to desired output and supply voltage source inverter which controlled by three-phase PWM generated by microcontroller. IGBT switched Voltage source inverter (VSI) produced alternating current (AC) voltage from direct current (DC) source to control speed of three-phase induction motor from boost converter output. Results showed that, the output power of solar module is optimized and controlled by using fuzzy logic controller. Besides that, the three-phase induction motor can be drive and control using VSI switching by the PWM signal generated by the fuzzy logic controller. This concluded that the non-linear system can be controlled and used in driving three-phase induction motor. (paper)

  12. A Novel Three Phase to Seven Phase Conversion Technique Using Transformer Winding Connections

    Directory of Open Access Journals (Sweden)

    M. Tabrez

    2017-10-01

    Full Text Available This paper proposes a novel multiphase transformer connection scheme which converts three phase balanced AC input to seven phase balanced AC output. Generalized theory to convert a three phase utility supply into any number of phases is presented. Based on the proposed generalized principle, a three phase to seven phase power converting transformer design is presented with connection scheme, analysis and simulation and experimental results of the proposed three phase to seven phase conversion transformer. The proposed transformer in this paper is analyzed and compared with the connection scheme for seven phase available in the literature. The connection scheme is found to have higher power density, lower core area and lower core requirement as compared to the available connection scheme of the same rating. Impedance mismatching between different phases of the transformer is observed in the three phase to seven phase transformer available in the literature. As this mismatching introduces error in study of per phase equivalent circuit diagrams as well as imbalance in voltage and currents. The present design also addresses the impedance mismatching issue and reduces mismatching in the proposed transformer design. A prototype of the proposed system is developed and waveforms are presented. The proposed design is verified using simulation and validated using experimental approach.

  13. The semiquantitative three-phase bone scintigraphy on hemiplegic patients with earlier complex regional pain syndrome

    International Nuclear Information System (INIS)

    Li Fang; Liu Xingdang; Lu Zhihui; Liu Congjin

    2010-01-01

    Objective: To investigate the difference between the early phases and delay phase of three-phase bone scintigraphy on hemiplegic patients with earlier complex regional pain syndrome (CRPS). Methods: Twenty-nine stroke patients with hemiplegia complicating CRPS received three-phase bone scintigraphy after intravenous injection of 99 Tc m -methylene diphosphonate (MDP). The region of interest (ROI) technique was used to obtain the radioactive counts of involved joints and contralateral sites on wrists, metacarpophalangeal, proximal interphalangeal and distal interphalangeal joints. The total counts of these four sites in each patient were then obtained and the total uptake ratios of involved joints/contralateral joints for each phase were calculated to compare the difference among the three phases. Wilcoxon test and ANOVA were used in data analyses. Results: The involved joints of hemiplegic side displayed higher tracer uptake. There were significant differences of the radioactive counts between involved joints and uninvolved ones in the perfusion, pool and delay phase (Wilcoxon test, Z: -4.73 to -2.10, P<0.05). There was no significant difference of total uptake ratios of involved joints/contralateral joints among the three phases (ANOVA, F = 0. 807, P < 0.05). Conclusions: Due to higher bone seeking agent accumulation on three-phase bone scintigraphy, both early phases and delay phase imaging showed similar value in stroke patients with hemiplegia complicating earlier CRPS. (authors)

  14. Real And Reactive Power Saving In Three Phase Induction Machine Using Star-Delta Switching Schemes

    Directory of Open Access Journals (Sweden)

    Ramesh Daravath

    2017-04-01

    Full Text Available Induction machines are the most commonly used industrial drives for variety of applications. It has been estimated that induction motors consumes approximately 50 of all the electric energy generated. Further in the area of renewable energy sources such as wind or bio-mass energy induction machines have been found suitable for functioning as generators. In this context it may be mentioned that a star-delta switching is common for the starting of three-phase induction motor. Now it is proposed to use this star-delta switching for energy conservation of induction machines i.e. at times of reduced loads the machine switched back to star connection. Using a three-phase 400 V 50 Hz 4-pole induction machine it has been demonstrated that the star-delta switching of stator winding of three-phase induction machine motor generator operations reconnected in star at suitable reduced loads with a switching arrangement can result in improved efficiency and power factor as compared to a fixed delta or star connection. The predetermined values along with the experimental results have also been presented in this report. A simulation program has been developed for the predetermination of performance of the three-phase induction machine using exact equivalent circuit. A case study on a 250 kW 400 V 4-pole three-phase induction machine operated with different load cycles reveals the significant real and reactive power savings that could be obtained in the present proposal.

  15. Compositional modeling of three-phase flow with gravity using higher-order finite element methods

    KAUST Repository

    Moortgat, Joachim

    2011-05-11

    A wide range of applications in subsurface flow involve water, a nonaqueous phase liquid (NAPL) or oil, and a gas phase, such as air or CO2. The numerical simulation of such processes is computationally challenging and requires accurate compositional modeling of three-phase flow in porous media. In this work, we simulate for the first time three-phase compositional flow using higher-order finite element methods. Gravity poses complications in modeling multiphase processes because it drives countercurrent flow among phases. To resolve this issue, we propose a new method for the upwinding of three-phase mobilities. Numerical examples, related to enhanced oil recovery and carbon sequestration, are presented to illustrate the capabilities of the proposed algorithm. We pay special attention to challenges associated with gravitational instabilities and take into account compressibility and various phase behavior effects, including swelling, viscosity changes, and vaporization. We find that the proposed higher-order method can capture sharp solution discontinuities, yielding accurate predictions of phase boundaries arising in computational three-phase flow. This work sets the stage for a broad extension of the higher-order methods for numerical simulation of three-phase flow for complex geometries and processes.

  16. Spatial support of knowledge production in higher education: Research paper

    OpenAIRE

    van Sprang, H; Groen, BH; van der Voordt, Theo

    2013-01-01

    This paper explores the impact of the physical and social dimensions of the work environment on satisfaction and perceived productivity of knowledge workers in Dutch universities of applied sciences. The approach took the form of a literature review, multiple case study of six research centres using interviews and logbook analysis, and web-based survey (N = 188). Optimally facilitating knowledge production requires both space for concentration (to support internalisation of knowledge) and spa...

  17. Health Behaviour Change Support Systems: Past Research and Future Challenges

    OpenAIRE

    Mettler, Tobias

    2015-01-01

    The emergence of mobile devices and social technologies has opened up new possibilities for health promotion and disease prevention. By means of emotional stimuli, motivation, and persuasion health behaviour change support systems (HBCSS) aim at influencing users to improve their health and wellbeing. This article presents the results of a bibliometric analysis related to the existing HBCSS body of knowledge. A total of 51 research studies were analysed with a look at their topical and theore...

  18. US nuclear reaction data program in support of basic research

    International Nuclear Information System (INIS)

    Bhat, M.R.; Chadwick, M.B.; Smith, M.S.

    1997-01-01

    Information about the US Nuclear Reaction Data Network (USNRDN) such as its members, work in progress, summaries of meetings, and organizational details may be found in its WWW Homepage. This paper is an overview of the data support provided by the network for basic research in nuclear astrophysics, radioactive ion beams, high energy heavy-ion and electron interactions and related activities involving all aspects of data stewardship

  19. Regulatory research and support program for 1989/90

    International Nuclear Information System (INIS)

    1989-01-01

    The Regulatory Research and Support Program is intended to augment and extend the Atomic Energy Control Board's regulatory program beyond the capability of in-house resources. The overall objective of the research and support program is to produce pertinent and independent information that will assist the Board and its staff in making correct, timely and credible decisions on regulating nuclear energy. The program is divided into eight main areas of research covering the safety of nuclear facilities, radioactive waste management, health physics, physical security and the development of regulatory processes. A total of 83 projects are planned for 1989/90, including a number which are ongoing from the previous fiscal year. Projects that are held in reserve in case funding becomes available are also listed. Most of the projects will be carried out under contracts issued through the Department of Supply and Services. This Information Bulletin contains a list of the projects with a brief description of each, and additional supporting information

  20. Establishment of a research pharmacy to support Ebola clinical research in Liberia.

    Science.gov (United States)

    Pierson, Jerome F; Kirchoff, Matthew Carl; Tyee, Rev Tijli; Montello, Michael J; Rhie, Julie K

    This article describes the establishment of a research pharmacy to support the Partnership for Research on Ebola Vaccines in Liberia (PREVAIL) vaccine study for Ebola virus disease. This article describes the establishment of the pharmacy element to support the overall research program during an Ebola outbreak in Monrovia, Liberia, in 2014 and 2015. The need for the rapid establishment of infrastructure to support the Liberia-United States joint clinical research partnership in response to the emerging Ebola virus disease provided the opportunity for collaboration among Liberian and U.S. pharmacists. Resource austere and research naïve. Research pharmacy prepared and randomized 1500 vaccinations in support of PREVAIL. Experiences of the Liberian and U.S. pharmacists involved in the program are described. The partnership was successful in the conduct of the study. More importantly, the capacity for Liberian pharmacists to support clinical research was established. In addition, the U.S. team learned several important lessons that will help prepare them for responding to research needs in future infectious disease outbreaks. Published by Elsevier Inc.

  1. IAEA Activities supporting education and training at research reactors

    International Nuclear Information System (INIS)

    Peld, N.D.; Ridikas, D.

    2013-01-01

    Full-text: Through the provision of neutrons for experiments and their historical association with universities, research reactors have played a prominent role in nuclear education and training of students, scientists and radiation workers. Today education and training remains the foremost application of research reactors, involving close to 160 facilities out of 246 operational. As part of its mandate to facilitate and expand the contribution of atomic energy to peace, health and prosperity throughout the world, the IAEA administers a number of activities intended to promote nuclear research and enable access to nuclear technology for peaceful purposes, one of which is the support of various education and training measures involving research reactors. In the last 5 years, education and training has formed one pillar for the creation of research reactor coalitions and networks to pool their resources and offer joint programmes, such as the on-going Group Fellowship Training Course. Conducted mainly through the Eastern European Research Reactor Initiative, this programme is a periodic sic week course for young scientists and engineers on nuclear techniques and administration jointly conducted at several member research reactor institutes. Organization of similar courses is under consideration in Latin America and the Asia-Pacific Region, also with support from the IAEA. Additionally, four research reactor institutes have begun offering practical education courses through virtual reactor experiments and operation known as the Internet Reactor Laboratory. Through little more than an internet connection and projection screens, university science departments can be connected regionally or bilaterally with the control room o a research reactor for various training activities. Finally, two publications are being prepared, namely Hands-On Training Courses Using Research Reactors and Accelerators, and Compendium on Education and training Based on Research Reactors. These

  2. The performance of a three-phase fluidized bed reactor in treatment of wastewater with high organic load

    Directory of Open Access Journals (Sweden)

    R. R. Souza

    2004-06-01

    Full Text Available An experimental study was carried out aiming to evaluate the performance of a three-phase fluidized bed bioreactor (FBBR used to treat milk wastewater. In this study three different concentrations of milk wastewater substrate (462, 825 and 1473 mg O2/L were tested. Using the same number of support particles, the results demonstrate that the average efficiency of COD removal decreased as the concentration of organic load in the substrate was increased. The growth of microorganism in the FBBR was followed by a count of viable cells in both liquid phase and the biofilms attached to the support. An increased number of viable cells were observed inside the reactor when it was used to degrade higher organic loads, with most of the cells on the support. The higher concentration of active biomass was responsible for achieving a relatively high absolute degradation of the wastewater containing the high organic load.

  3. Using PIDs to Support the Full Research Data Publishing Lifecycle

    Science.gov (United States)

    Waard, A. D.

    2016-12-01

    Persistent identifiers can help support scientific research, track scientific impact and let researchers achieve recognition for their work. We discuss a number of ways in which Elsevier utilizes PIDs to support the scholarly lifecycle: To improve the process of storing and sharing data, Mendeley Data (http://data.mendeley.com) makes use of persistent identifiers to support the dynamic nature of data and software, by tracking and recording the provenance and versioning of datasets. This system now allows the comparison of different versions of a dataset, to see precisely what was changed during a versioning update. To present research data in context for the reader, we include PIDs in research articles as hyperlinks: https://www.elsevier.com/books-and-journals/content-innovation/data-base-linking. In some cases, PIDs fetch data files from the repositories provide that allow the embedding of visualizations, e.g. with PANGAEA and PubChem: https://www.elsevier.com/books-and-journals/content-innovation/protein-viewer; https://www.elsevier.com/books-and-journals/content-innovation/pubchem. To normalize referenced data elements, the Resource Identification Initiative - which we developed together with members of the Force11 RRID group - introduces a unified standard for resource identifiers (RRIDs) that can easily be interpreted by both humans and text mining tools. https://www.force11.org/group/resource-identification-initiative/update-resource-identification-initiative, as can be seen in our Antibody Data app: https://www.elsevier.com/books-and-journals/content-innovation/antibody-data To enable better citation practices and support robust metrics system for sharing research data, we have helped develop, and are early adopters of the Force11 Data Citation Principles and Implementation groups (https://www.force11.org/group/dcip) Lastly, through our work with the Research Data Alliance Publishing Data Services group, we helped create a set of guidelines (http

  4. Effect of borojo (Borojoa patinoi Cuatrecasas) three-phase composition and gum arabic on the glass transition temperature.

    Science.gov (United States)

    Rodríguez-Bernal, Jenny M; Tello, Edisson; Flores-Andrade, Enrique; Perea-Flores, Maria de Jesús; Vallejo-Cardona, Alba A; Gutiérrez-López, Gustavo F; Quintanilla-Carvajal, Maria X

    2016-02-01

    The search for natural, novel, high-quality, stable food ingredients is an ongoing practice in the food industry. Pulp of borojo (Borojoa patinoi Cuatrecasas), which is a fruit of the Colombian Pacific region, can be separated into three phases: liquid (LP), medium (MP) and solid (SP) phases. The objective of this work was to evaluate the effect of the three-phase composition and gum arabic on their glass transitions temperatures (T(g)). The best mixture, LP-MP, MP-SP and LP-SP and gum arabic (GA) was identified by response surface methodology. When adding GA to SP borojo phase in a 1:1 proportion, the resulting T(g) of the mixture was 132.27 °C whereas Tg for GA and SP-phase were 154.89 °C and 79.86 °C respectively, which supported this combination as attractive from a processing perspective and supports an industrial advantage of using borojo as food ingredient. Phases were characterized by high-performance liquid chromatography, Fourier transform infrared spectroscopy, confocal laser scanning microscopy and mass spectrometry. Low molecular weight compounds such as fructose for MP lowered T(g) whereas the presence of lignin increased T(g) of the mixtures as with the SP. The addition of GA significantly increased T(g) of borojo phases so leading to propose them as novel food processing materials. © 2015 Society of Chemical Industry.

  5. Three-phase distillation. Simulation and application to the separation of fermentation products

    Energy Technology Data Exchange (ETDEWEB)

    Pucci, A; Mikitenko, P; Asselineau, L

    1986-01-01

    In recent years, most of the simulation methods proposed for solving distillation problems in which three-phase distillation occurs use a Newton-Raphson or a comparable approach which requires an initial estimate of variables close enough to the final answer. A plate-to-plate calculation which is more likely to converge on the solution is presented here. The phase equilibria are represented by the NRTL model. The position of three-phase stages is solved automatically. Another three-phase distillation program operating at infinite reflux first supplies the location of feeds and/or sidestreams and computes the minimum number of stages for a given separation. An application of the proposed method is illustrated by the rectification of butanol-acetone fermentation products. The calculated results are in good agreement with the experimental data obtained from the operation of a laboratory glass-plate-type column. 19 references, 8 figures, 1 table.

  6. A novel proposal of cooperation between a cage induction generator and the three-phase grid

    Directory of Open Access Journals (Sweden)

    Szular Zbigniew

    2016-01-01

    Full Text Available In the paper, a new concept of the cooperation between a cage induction generator and the three-phase grid is presented. The induction generator is excited by a capacitor battery connected to the stator winding terminals. In order to ensure a stable operation, the battery capacity should be continuously adjusted. Three appropriate selected capacitors are connected to the stator winding terminals by means of two bi-directional controlled switches. The generator output voltage is stabilized by a suitable control of these switches. The stator winding terminals are also connected to the diode bridge rectifier. Energy in the DC bus is converted to the parameters of the three-phase grid (400 V, 50 Hz by means of a three-phase voltage source inverter. Examples of numerical calculation results of the proposed energy generation system are presented in the end part of the paper.

  7. Adaptive nonlinear control of single-phase to three-phase UPS system

    Directory of Open Access Journals (Sweden)

    Kissaoui M.

    2014-01-01

    Full Text Available This work deals with the problems of uninterruptible power supplies (UPS based on the single-phase to three-phase converters built in two stages: an input bridge rectifier and an output three phase inverter. The two blocks are joined by a continuous intermediate bus. The objective of control is threefold: i power factor correction “PFC”, ii generating a symmetrical three-phase system at the output even if the load is unknown, iii regulating the DC bus voltage. The synthesis of controllers has been reached by two nonlinear techniques that are the sliding mode and adaptive backstepping control. The performances of regulators have been validated by numerical simulation in MATLAB / SIMULINK.

  8. Numerical Simulation on Flow Field of Oilfield Three-Phase Separator

    Directory of Open Access Journals (Sweden)

    Yong-tu Liang

    2013-01-01

    Full Text Available The conventional measurement method can no longer guarantee the accuracy requirement after the oilfield development entering high water cut stage, due to the water content and gas phase in the flow. In order to overcome the impact of measurement deviation the oilfield production management, the flow field of three-phase separator is studied numerically in this paper using Fluent 6.3.26. Taking into consideration the production situation of PetroChina Huabei Oilfield and the characteristics of three-phase separator, the effect of internal flow status as well as other factors such as varying flow rate, gas fraction, and water content on the separation efficiency is analyzed. The results show that the separation efficiencies under all operation conditions are larger than 95%, which satisfy the accuracy requirement and also provide the theoretical foundation for the application of three-phase separators at oilfields.

  9. Building organizational supports for research-minded practitioners.

    Science.gov (United States)

    Austin, Michael J; Dal Santo, Teresa S; Lee, Chris

    2012-01-01

    One of the biggest challenges facing human service organizations is the proliferation of information from inside and outside the agency that needs to be managed if it is to be of use. The concepts of tacit and explicit knowledge can inform an approach to this challenge. Tacit knowledge is stored in the minds of practitioners (often called practice wisdom) and the explicit knowledge is often found in organizational procedure manuals and educational and training materials. Building on this perspective, this analysis provides a preliminary definition of research-minded practitioners by explicating the elements of curiosity, critical reflection, and critical thinking. The organizational implications of developing a cadre of research-minded practitioners include the commitment of top management to support "link officers", evidence request services, research and development units, and service standards. The challenges include the capacity to identify/support research-minded practitioners, promote an organizational culture of evidence-informed practice, redefine staff development and training, redefine job descriptions, and specify the nature of managerial leadership. Copyright © Taylor & Francis Group, LLC

  10. COMPUTATIONAL AND EXPERIMENTAL MODELING OF THREE-PHASE SLURRY-BUBBLE COLUMN REACTOR

    Energy Technology Data Exchange (ETDEWEB)

    Isaac K. Gamwo; Dimitri Gidaspow

    1999-09-01

    Considerable progress has been achieved in understanding three-phase reactors from the point of view of kinetic theory. In a paper in press for publication in Chemical Engineering Science (Wu and Gidaspow, 1999) we have obtained a complete numerical solution of bubble column reactors. In view of the complexity of the simulation a better understanding of the processes using simplified analytical solutions is required. Such analytical solutions are presented in the attached paper, Large Scale Oscillations or Gravity Waves in Risers and Bubbling Beds. This paper presents analytical solutions for bubbling frequencies and standing wave flow patterns. The flow patterns in operating slurry bubble column reactors are not optimum. They involve upflow in the center and downflow at the walls. It may be possible to control flow patterns by proper redistribution of heat exchangers in slurry bubble column reactors. We also believe that the catalyst size in operating slurry bubble column reactors is not optimum. To obtain an optimum size we are following up on the observation of George Cody of Exxon who reported a maximum granular temperature (random particle kinetic energy) for a particle size of 90 microns. The attached paper, Turbulence of Particles in a CFB and Slurry Bubble Columns Using Kinetic Theory, supports George Cody's observations. However, our explanation for the existence of the maximum in granular temperature differs from that proposed by George Cody. Further computer simulations and experiments involving measurements of granular temperature are needed to obtain a sound theoretical explanation for the possible existence of an optimum catalyst size.

  11. Multi-Scale Long-Range Magnitude and Sign Correlations in Vertical Upward Oil-Gas-Water Three-Phase Flow

    Science.gov (United States)

    Zhao, An; Jin, Ning-de; Ren, Ying-yu; Zhu, Lei; Yang, Xia

    2016-01-01

    In this article we apply an approach to identify the oil-gas-water three-phase flow patterns in vertical upwards 20 mm inner-diameter pipe based on the conductance fluctuating signals. We use the approach to analyse the signals with long-range correlations by decomposing the signal increment series into magnitude and sign series and extracting their scaling properties. We find that the magnitude series relates to nonlinear properties of the original time series, whereas the sign series relates to the linear properties. The research shows that the oil-gas-water three-phase flows (slug flow, churn flow, bubble flow) can be classified by a combination of scaling exponents of magnitude and sign series. This study provides a new way of characterising linear and nonlinear properties embedded in oil-gas-water three-phase flows.

  12. Non clinical research at CENTIS supporting biotechnological and pharmaceutical industry

    International Nuclear Information System (INIS)

    Hernandez Gonzalez, Ignacio

    2012-01-01

    Drugs production is a highly demanding industry because the rigor of legislations and guidelines. Standards are applied to manufacturing facilities and also to research and development stage. Our national biotechnological industry is developing and producing important medications for diseases like cancer, some of them in the national and international market. Isotopes Centre is an institution supporting such development by means of a work platform to carry out researches in the field of pharmacokinetic and biodistribution in experimental models. Accumulated experience allows us to contribute to research and development of different kind of molecules as pharmaceuticals, specially the biotechnological ones. We are evolving in direction to new technologies and methodologies more suitable to current standards. Radiolabeling is still a convenient choice considering present and new imaging technologies to investigate distribution and kinetic in living subjects. With the techniques we have and the ones to incorporate in a near future, new and more demanding investigations will be affordable. (author)

  13. Single-phase DECT with VNCT compared with three-phase CTU in patients with haematuria

    Energy Technology Data Exchange (ETDEWEB)

    Park, Jung Jae; Park, Byung Kwan; Kim, Chan Kyo [Sungkyunkwan University School of Medicine, Department of Radiology, Samsung Medical Center, Seoul (Korea, Republic of)

    2016-10-15

    To retrospectively evaluate the diagnostic performance of single-phase dual-energy CT (DECT) with virtual non-contrast CT (VNCT) compared with three-phase CT urography (CTU) in patients with haematuria. A total of 296 patients underwent three-phase CTU (NCT at 120 kVp; nephrographic phase and excretory phase DECTs at 140 kVp and 80 kVp) owing to haematuria. Diagnostic performances of CT scans were compared for detecting urothelial tumours and urinary stones. Dose-length product (DLP) was compared in relation to single-phase DECT and three-phase CTU Dose-length product (DLP) was compared in relation to single-phase DECT and three-phase CTU. Sensitivity and specificity for tumour were 95 % (19/20) and 98.9 % (273/276) on CTU, 95 % (19/20) and 98.2 % (271/276) on nephrographic phase DECT, and 90 % (18/20) and 98.2 % (271/276) on excretory phase DECT (P > 0.1). Of the 148 stones detected on NCT, 108 (73 %) and 100 (67.6 %) were detected on nephrographic phase and excretory phase VNCTs, respectively. The mean size of stones undetected on nephrographic and excretory VNCTs was measured as 1.5 ± 0.5 mm and 1.6 ± 0.6 mm, respectively. The mean DLPs of three-phase CTU, nephrographic phase DECT and excretory phase DECT were 1076 ± 248 mGy . cm, 410 ± 98 mGy . cm, and 360 ± 87 mGy . cm, respectively (P < 0.001). Single-phase DECT has a potential to replace three-phase CTU for detecting tumours with a lower radiation dose. (orig.)

  14. Leakage Current Elimination of Four-Leg Inverter for Transformerless Three-Phase PV Systems

    DEFF Research Database (Denmark)

    Guo, Xiaoqiang; He, Ran; Jian, Jiamin

    2016-01-01

    Eliminating the leakage current is one of the most important issues for transformerless three phase photovoltaic (PV) systems. In this paper, the leakage current elimination of a three-phase four-leg PV inverter is investigated. With the common mode loop model established, the generation mechanism...... of the leakage current is clearly identified. Different typical carrier-based modulation methods and their corresponding common mode voltages are discussed. A new modulation strategy with Boolean logic function is proposed to achieve the constant common mode voltage for the leakage current reduction. Finally...

  15. High frequency three-phase PWM grid connected drive using silicon-carbide switches

    DEFF Research Database (Denmark)

    Kouchaki, Alireza; Pedersen, Jacob Lykke; Nymand, Morten

    2016-01-01

    This paper presents controller design procedure for a fully silicon-carbide (SiC) based three-phase grid-connected PWM drive. The influence of the feedforward compensation for the presented setup is studied and the transfer function of the system with feedforward is derived and compared with the ......This paper presents controller design procedure for a fully silicon-carbide (SiC) based three-phase grid-connected PWM drive. The influence of the feedforward compensation for the presented setup is studied and the transfer function of the system with feedforward is derived and compared...

  16. Model and Frequency Control for Three-Phase Wireless Power Transfer System

    Directory of Open Access Journals (Sweden)

    Chenyang Xia

    2016-01-01

    Full Text Available In order to the eliminate the “dead spot” in the traditional three-phase wireless power transfer (WPT system, a three-phase WPT system with an asymmetric magnetic circuit is presented in this paper. Additionally, mathematical model of the system is established and the system parameters are optimized. Based on the fact that the resonant frequency and efficiency are greatly varied with the load, a method based on impedance conversion is further proposed to improve the frequency stability and system efficiency. Finally, simulation and experimental results show that the proposed method is reliable and feasible to eliminate the “dead spot.”

  17. Four-branch Star Hybrid Power Filter for Three-phase Four-wire Systems

    DEFF Research Database (Denmark)

    Blaabjerg, Frede; Teodorescu, Remus; Rodriguez, Pedro

    2008-01-01

    and derives fundamental concepts about the control of the resulting hybrid power filter. From this analysis, a specifc implementation of a three-phase four-wire hybrid power filter is presented as an illustrative application of the filtering topology. An extensive evaluation using simulation and experimental......This paper presents a new concept for filtering current harmonics in three-phase four-wire networks. The four-branch star (FBS) filtering topology presented in this work is characterized by a particular layout consisting of single-phase inductances and capacitors. Via this layout, a power filter...

  18. Modeling and control of three phase rectifier with electronic smoothing inductor

    DEFF Research Database (Denmark)

    Singh, Yash Veer; Rasmussen, Peter Omand; Andersen, Torben Ole

    2011-01-01

    This paper presents a simple, direct method for deriving the approximate, small-signal, average model and control strategy for three-phase diode bridge rectifier operating with electronic smoothing technique. Electronic smoothing inductor (ESI) performs the function of an inductor that has...... controlled variable impedance. This increases power factor (PF) and reduces total harmonic distortions (THDs) in mains current. The ESI based rectifier enables compact and cost effective design of three phase electric drive as size of passive components is reduced significantly. In order to carry out...

  19. Three-phase multilevel inverter configuration for open-winding high power application

    DEFF Research Database (Denmark)

    Sanjeevikumar, Padmanaban; Blaabjerg, Frede; Wheeler, Patrick William

    2015-01-01

    This paper work exploits a new dual open-winding three-phase multilevel inverter configuration suitable for high power medium-voltage applications. Modular structure comprised of standard three-phase voltage source inverter (VSI) along with one additional bi-directional semiconductor device (MOSFET...... for implementation purpose. Proposed dual-inverter configuration generates multilevel outputs with benefit includes reduced THD and dv/dt in comparison to other dual-inverter topologies. Complete model of the multilevel ac drive is developed with simple MSCFM modulation in Matlab/PLECs numerical software...

  20. Three-Phase Modulated Pole Machine Topologies Utilizing Mutual Flux Paths

    DEFF Research Database (Denmark)

    Washington, Jamie G.; Atkinson, Glynn J.; Baker, Nick J.

    2012-01-01

    This paper discusses three-phase topologies for modulated pole machines (MPMs). The authors introduce a new threephase topology, which takes advantage of mutual flux paths; this is analyzed using 3-D finite-element methods and compared to a three-phase topology using three single-phase units...... stacked axially. The results show that the new “combined-phase MPM” exhibits a greater torque density, while offering a reduction in the number of components. The results obtained from two prototypes are also presented to verify the concept; the results show that the “combined-phase” machine could provide...

  1. Control Method for DC-Link Voltage Ripple Cancellation in Voltage Source Inverter under Unbalanced Three-Phase Voltage Supply Conditions

    Czech Academy of Sciences Publication Activity Database

    Chomát, Miroslav; Schreier, Luděk

    2005-01-01

    Roč. 152, č. 3 (2005), s. 494-500 ISSN 1350-2352 R&D Projects: GA ČR(CZ) GA102/02/0554 Institutional research plan: CEZ:AV0Z20570509 Keywords : DC-link voltage * unbalanced three-phase voltage Subject RIV: JA - Electronics ; Optoelectronics, Electrical Engineering Impact factor: 0.587, year: 2005

  2. Total connectivity speeds research and support of field operations

    International Nuclear Information System (INIS)

    Himes, R.E.; Frost, K.I.; Henry, S.R.; Funkhouser, J.D.

    1992-01-01

    This paper reports that research and field support roles in the oilfield service industry have become increasingly complex in the last 15 years. Experimental apparatus are more dependent on the data-acquisition and processing capabilities of computers as the amount of data generated increases. Therefore, the need to network these computers for data transport has significantly increased. The type of network system selected depends on the goals to be achieved. Incorporation of existing equipment, communication between systems of different architectures, and future expandability are only a few of the necessary attributes. With these in mind, a computer network system was designed and is being implemented. The system combines local- and wide-area networks (LAN's or WAN's) of different protocols to acquire, process, and transport information worldwide. The result is faster development of new products and quicker response in support of field operations

  3. Constellation Program Electrical Ground Support Equipment Research and Development

    Science.gov (United States)

    McCoy, Keegan S.

    2010-01-01

    At the Kennedy Space Center, I engaged in the research and development of electrical ground support equipment for NASA's Constellation Program. Timing characteristics playa crucial role in ground support communications. Latency and jitter are two problems that must be understood so that communications are timely and consistent within the Kennedy Ground Control System (KGCS). I conducted latency and jitter tests using Alien-Bradley programmable logic controllers (PLCs) so that these two intrinsic network properties can be reduced. Time stamping and clock synchronization also play significant roles in launch processing and operations. Using RSLogix 5000 project files and Wireshark network protocol analyzing software, I verified master/slave PLC Ethernet module clock synchronization, master/slave IEEE 1588 communications, and time stamping capabilities. All of the timing and synchronization test results are useful in assessing the current KGCS operational level and determining improvements for the future.

  4. Using Google Earth in Marine Research and Operational Decision Support

    Science.gov (United States)

    Blower, J. D.; Bretherton, D.; Haines, K.; Liu, C.; Rawlings, C.; Santokhee, A.; Smith, I.

    2006-12-01

    A key advantage of Virtual Globes ("geobrowsers") such as Google Earth is that they can display many different geospatial data types at a huge range of spatial scales. In this demonstration and poster display we shall show how marine data from disparate sources can be brought together in a geobrowser in order to support both scientific research and operational search and rescue activities. We have developed the Godiva2 interactive website for browsing and exploring marine data, mainly output from supercomputer analyses and predictions of ocean circulation. The user chooses a number of parameters (e.g. sea temperature at 100m depth on 1st July 2006) and can load an image of the resulting data in Google Earth. Through the use of an automatically-refreshing NetworkLink the user can explore the whole globe at a very large range of spatial scales: the displayed data will automatically be refreshed to show data at increasingly fine resolution as the user zooms in. This is a valuable research tool for exploring these terabyte- scale datasets. Many coastguard organizations around the world use SARIS, a software application produced by BMT Cordah Ltd., to predict the drift pattern of objects in the sea in order to support search and rescue operations. Different drifting objects have different trajectories depending on factors such as their buoyancy and windage and so a computer model, supported by meteorological and oceanographic data, is needed to help rescuers locate their targets. We shall demonstrate how Google Earth is used to display output from the SARIS model (including the search target location and associated error polygon) alongside meteorological data (wind vectors) and oceanographic data (sea temperature, surface currents) from Godiva2 in order to support decision-making. We shall also discuss the limitations of using Google Earth in this context: these include the difficulties of working with time- dependent data and the need to access data securely. essc

  5. Decomposition of Composite Electric Field in a Three-Phase D-Dot Voltage Transducer Measuring System

    Directory of Open Access Journals (Sweden)

    Xueqi Hu

    2016-10-01

    Full Text Available In line with the wider application of non-contact voltage transducers in the engineering field, transducers are required to have better performance for different measuring environments. In the present study, the D-dot voltage transducer is further improved based on previous research in order to meet the requirements for long-distance measurement of electric transmission lines. When measuring three-phase electric transmission lines, problems such as synchronous data collection and composite electric field need to be resolved. A decomposition method is proposed with respect to the superimposed electric field generated between neighboring phases. The charge simulation method is utilized to deduce the decomposition equation of the composite electric field and the validity of the proposed method is verified by simulation calculation software. With the deduced equation as the algorithm foundation, this paper improves hardware circuits, establishes a measuring system and constructs an experimental platform for examination. Under experimental conditions, a 10 kV electric transmission line was tested for steady-state errors, and the measuring results of the transducer and the high-voltage detection head were compared. Ansoft Maxwell Stimulation Software was adopted to obtain the electric field intensity in different positions under transmission lines; its values and the measuring values of the transducer were also compared. Experimental results show that the three-phase transducer is characterized by a relatively good synchronization for data measurement, measuring results with high precision, and an error ratio within a prescribed limit. Therefore, the proposed three-phase transducer can be broadly applied and popularized in the engineering field.

  6. Supporting the evolution of research in software ecosystems

    DEFF Research Database (Denmark)

    Manikas, Konstantinos

    2016-01-01

    with significant lack of software ecosystem specific theories that are solid, mature, generic, and detailed enough to be measurable and transferable. In this study, we intent to come closer to an evolution of the field by supporting the “localization” of research, i.e. the focus on specific types of software...... software ecosystem studies lack deeper investigation of technical and collaborative aspects. Moreover, we identify an increased focus on organizational aspects and a rather limited focus on business. Furthermore, we identify common technology as the component investigated most in the ecosystems, both from...

  7. Overview of NASA supported Stirling thermodynamic loss research

    International Nuclear Information System (INIS)

    Tew, R.C.; Geng, S.M.

    1994-01-01

    The National Aeronautics and Space Administration (NASA) is funding research to characterize Stirling machine thermodynamic losses. NASA's primary goal is to improve Stirling design codes to support engine development for space and terrestrial power. However, much of the fundamental data is applicable to Stirling cooler and heat pump applications. The research results are reviewed. Much has been learned about oscillating-flow hydrodynamics, including laminar/turbulent transition, and tabulated data has been documented for further analysis. Now, with a better understanding of the oscillator-flow field, it is time to begin measuring the effects of oscillating flow and oscillating pressure level on heat transfer in heat exchanger flow passages and in cylinders. This critical phase of the work is just beginning

  8. Three-phase Power Flow Calculation of Low Voltage Distribution Network Considering Characteristics of Residents Load

    Science.gov (United States)

    Wang, Yaping; Lin, Shunjiang; Yang, Zhibin

    2017-05-01

    In the traditional three-phase power flow calculation of the low voltage distribution network, the load model is described as constant power. Since this model cannot reflect the characteristics of actual loads, the result of the traditional calculation is always different from the actual situation. In this paper, the load model in which dynamic load represented by air conditioners parallel with static load represented by lighting loads is used to describe characteristics of residents load, and the three-phase power flow calculation model is proposed. The power flow calculation model includes the power balance equations of three-phase (A,B,C), the current balance equations of phase 0, and the torque balancing equations of induction motors in air conditioners. And then an alternating iterative algorithm of induction motor torque balance equations with each node balance equations is proposed to solve the three-phase power flow model. This method is applied to an actual low voltage distribution network of residents load, and by the calculation of three different operating states of air conditioners, the result demonstrates the effectiveness of the proposed model and the algorithm.

  9. Three-phase scintigraphy in epicondylitis of the lateral lower humerus

    Energy Technology Data Exchange (ETDEWEB)

    Koppers, B.; Riel, K.

    1982-08-01

    Ten patients with tennis elbow were examined by three-phase scintigraphy, using sup(99m)Tc-MDP. In agreement with the histological findings of H. Schneider (14), there was no uptake during the perfusion and soft tissue phase. In the phase, there was focal bone uptake in one patient only.

  10. Three-phase scintigraphy in epicondylitis of the lateral lower humerus

    International Nuclear Information System (INIS)

    Koppers, B.; Riel, K.; Technische Univ. Muenchen

    1982-01-01

    Ten patients with tennis elbow were examined by three-phase scintigraphy, using sup(99m)Tc-MDP. In agreement with the histological findings of H. Schneider (14), there was no uptake during the perfusion and soft tissue phase. In the phase, there was focal bone uptake in one patient only. (orig.) [de

  11. THREE-PHASE ENERGY SUPPLY SYSTEMS SIMULATION FOR THE TOTAL POWER LOSSES COMPONENTS ASSESSMENT

    Directory of Open Access Journals (Sweden)

    D.V. Tugay

    2016-09-01

    Full Text Available Purpose. The goal is to optimize a structure of Matlab-model of the three-phase energy supply system with power active filter. The mathematical model that describes the energy supply system modes of operation which contains additional losses is proposed. Methodology. We have applied concepts of the electrical circuits theory, mathematical modeling elements based on linear algebra and vector calculus, mathematical simulation in Matlab package. Results. We have developed two models of three-phase energy supply system. The first one is based on a vector representation, and the second one on the matrix representation of energy processes. Using these models we have solved the problem of maintaining unchanged the average useful power for 279 cases of energy supply system modes of operation. Originality. We have developed methods of mathematical analysis of a three-phase energy supply systems with polyharmonic voltages and currents in the symmetric and asymmetric modes. Practical value. We have created Matlab-model of a three-phase energy supply system with automated calculation of a correction factor. It allows reducing more than one order the time for energy processes elucidation in multiphase systems.

  12. A Phase Current Reconstruction Approach for Three-Phase Permanent-Magnet Synchronous Motor Drive

    Directory of Open Access Journals (Sweden)

    Hao Yan

    2016-10-01

    Full Text Available Three-phase permanent-magnet synchronous motors (PMSMs are widely used in renewable energy applications such as wind power generation, tidal energy and electric vehicles owing to their merits such as high efficiency, high precision and high reliability. To reduce the cost and volume of the drive system, techniques of reconstructing three-phase current using a single current sensor have been reported for three-phase alternating current (AC control system using the power converts. In existing studies, the reconstruction precision is largely influenced by reconstructing dead zones on the Space Vector Pulse Width Modulation (SVPWM plane, which requires other algorithms to compensate either by modifying PWM modulation or by phase-shifting of the PWM signal. In this paper, a novel extended phase current reconstruction approach for PMSM drive is proposed. Six novel installation positions are obtained by analyzing the sampling results of the current paths between each two power switches. By arranging the single current sensor at these positions, the single current sensor is sampled during zero voltage vectors (ZVV without modifying the PWM signals. This proposed method can reconstruct the three-phase currents without any complex algorithms and is available in the sector boundary region and low modulation region. Finally, this method is validated by experiments.

  13. Active Damping Control Methods for Three-Phase Slim DC-link Drive System

    DEFF Research Database (Denmark)

    Yang, Feng; Wang, Dong; Blaabjerg, Frede

    2017-01-01

    for stabilizing such slim dc-link drives together with the benefit of low cost and high flexibility. This paper gives an overview of the state-of-the-art active damping methods for the three-phase slim dc-link drive. The main pros and cons of each method are identified. The theoretical comparison is validated...

  14. Development of an expert system for three-phase induction motors

    NARCIS (Netherlands)

    Sprangers, R.L.J.; Motoasca, T.E.; Lomonova, E.

    2012-01-01

    This work presents the design of an Expert System (Motor Design Software Tool - MDST) that will be used for design and analysis of three-phase induction motors. A suitable selection between numerous models and parameter calculation methods provided by literature is made and discussed. The models are

  15. Three-Phase Grid-Connected of Photovoltaic Generator Using Nonlinear Control

    DEFF Research Database (Denmark)

    Yahya, A.; El Fadil, H.; Guerrero, Josep M.

    2014-01-01

    This paper proposes a nonlinear control methodology for three phase grid connected of PV generator. It consists of a PV arrays; a voltage source inverter, a grid filter and an electric grid. The controller objectives are threefold: i) ensuring the Maximum power point tracking (MPPT) in the side...... stability analysis and simulation results that the proposed controller meets all the objectives....

  16. A Smart Current Modulation Scheme for Harmonic Reduction in Three- Phase Motor Drive Applications

    DEFF Research Database (Denmark)

    Davari, Pooya; Zare, Firuz; Blaabjerg, Frede

    2015-01-01

    Electric motor-driven systems consume considerable amount of the global electricity. Majority of three-phase motor drives are equipped with conventional diode rectifier and passive harmonic mitigation, being witnessed as the main source in generating input current harmonics. While many active har...

  17. High-power three-port three-phase bidirectional DC-DC converter

    NARCIS (Netherlands)

    Tao, H.; Duarte, J.L.; Hendrix, M.A.M.

    2007-01-01

    This paper proposes a three-port three-phase bidirectional dc-dc converter suitable for high-power applications. The converter combines a slow primary source and a fast storage to power a common load (e.g., an inverter). Since this type of system is gaining popularity in sustainable energy

  18. A Multipulse Pattern Modulation Scheme for Harmonic Mitigation in Three-Phase Multimotor Drives

    DEFF Research Database (Denmark)

    Davari, Pooya; Yang, Yongheng; Zare, Firuz

    2016-01-01

    , which thus deteriorates the power grid quality and also lowers the conversion efficiency. Both degradations are apt to occur in motor drive applications. At present, many industrial drives are equipped with three-phase diode rectifiers and employ passive filtering techniques on the AC or DC side...

  19. Optimal Power Flow in three-phase islanded microgrids with inverter interfaced units

    DEFF Research Database (Denmark)

    Sanseverino, Eleonora Riva; Quang, Ninh Nguyen; Di Silvestre, Maria Luisa

    2015-01-01

    In this paper, the solution of the Optimal Power Flow (OPF) problem for three phase islanded microgrids is studied, the OPF being one of the core functions of the tertiary regulation level for an AC islanded microgrid with a hierarchical control architecture. The study also aims at evaluating the...

  20. Optimal power flow based on glow worm-swarm optimization for three-phase islanded microgrids

    DEFF Research Database (Denmark)

    Quang, Ninh Nguyen; Sanseverino, Eleonora Riva; Di Silvestre, Maria Luisa

    2014-01-01

    This paper presents an application of the Glowworm Swarm Optimization method (GSO) to solve the optimal power flow problem in three-phase islanded microgrids equipped with power electronics dc-ac inverter interfaced distributed generation units. In this system, the power injected by the distribut...

  1. A Voltage Modulated DPC Approach for Three-Phase PWM Rectifier

    DEFF Research Database (Denmark)

    Gui, Yonghao; Li, Mingshen; Lu, Jinghang

    2018-01-01

    In this paper, a voltage modulated direct power control for three-phase pulse-width modulated rectifier is proposed. With the suggested method, the differential equations describing the rectifier dynamics are changing from a linear time-varying system into a linear time-invariant one. In this way...

  2. Three Phase Six-Switch PWM Buck Rectifier with Power Factor Improvement

    DEFF Research Database (Denmark)

    Zafar Ullah Khan, M; Mohsin Naveed, M.; Hussain, Dil Muhammad Akbar

    2013-01-01

    Conventional Phase Controlled Rectifier injects low order current harmonics into the AC mains. Large size filtering components are required to attenuate these harmonics. In this paper, Three Phase Six-Switch PWM Buck Rectifier[1] is presented which operates at nearly unity power factor and provides...

  3. Predictive Duty Cycle Control of Three-Phase Active-Front-End Rectifiers

    DEFF Research Database (Denmark)

    Song, Zhanfeng; Tian, Yanjun; Chen, Wei

    2016-01-01

    This paper proposed an on-line optimizing duty cycle control approach for three-phase active-front-end rectifiers, aiming to obtain the optimal control actions under different operating conditions. Similar to finite control set model predictive control strategy, a cost function previously...

  4. A low cost rapid prototype platform for a three phase PFC rectifier application

    DEFF Research Database (Denmark)

    Haase, Frerk; Kouchaki, Alireza; Nymand, Morten

    2015-01-01

    In this paper the design and development of a low cost rapid prototype platform for a Three Phase PFC rectifier application is presented. The active rectifier consists of a SiC-MOSFET based PWM converter and a low cost rapid prototype platform for simulating and implementing the digital control...

  5. Stability Improvements of an LCL-filter based Three-phase Active Rectifier

    DEFF Research Database (Denmark)

    Liserre, Marco; Dell'Aquila, Antonio; Blaabjerg, Frede

    2002-01-01

    Three-phase active rectifiers guarantee sinusoidal input currents and controllable dc voltage at the price of a high switching frequency ripple that can disturb and reduce efficiency of other EMI sensitive equipment connected to the grid. This problem could be solved choosing a high value...

  6. A laboratory grid simulator based on three-phase four-leg inverter

    DEFF Research Database (Denmark)

    Li, Fei; Wang, Xiongfei; Chen, Zhe

    2011-01-01

    This paper presents the design and implementation of a laboratory grid simulator which is used to test the grid-connected devices according to the strict standards. Three-phase four-leg inverter with direct voltage control in Natural Frame is adopted in this grid simulator, which significantly...

  7. Three-Phase Cascaded Multilevel Inverter Using Power Cells With Two Inverter Legs in Series

    NARCIS (Netherlands)

    Waltrich, G.; Barbi, I.

    2010-01-01

    In this paper, a modular three-phase multilevel inverter specially suited for electrical drive applications is proposed. Unlike the cascaded H-bridge inverter, this topology is based on power cells connected in cascade using two inverter legs in series. A detailed analysis of the structure and the

  8. A Three-Phase Microgrid Restoration Model Considering Unbalanced Operation of Distributed Generation

    International Nuclear Information System (INIS)

    Wang, Zeyu; Wang, Jianhui; Chen, Chen

    2016-01-01

    Recent severe outages highlight the urgency of improving grid resiliency in the U.S. Microgrid formation schemes are proposed to restore critical loads after outages occur. Most distribution networks have unbalanced configurations that are not represented in sufficient detail by single-phase models. This study provides a microgrid formation plan that adopts a three-phase network model to represent unbalanced distribution networks. The problem formulation has a quadratic objective function with mixed-integer linear constraints. The three-phase network model enables us to examine the three-phase power outputs of distributed generators (DGs), preventing unbalanced operation that might trip DGs. Because the DG unbalanced operation constraint is non-convex, an iterative process is presented that checks whether the unbalanced operation limits for DGs are satisfied after each iteration of optimization. We also develop a relatively conservative linear approximation on the unbalanced operation constraint to handle larger networks. Compared with the iterative solution process, the conservative linear approximation is able to accelerate the solution process at the cost of sacrificing optimality to a limited extent. Simulation in the IEEE 34 node and IEEE 123 test feeders indicate that the proposed method yields more practical microgrid formations results. In addition, this paper explores the coordinated operation of DGs and energy storage (ES) installations. The unbalanced three-phase outputs of ESs combined with the relatively balanced outputs of DGs could supply unbalanced loads. In conclusion, the case study also validates the DG-ES coordination.

  9. A control strategy based on UTT and I CosΘ theory of three-phase ...

    African Journals Online (AJOL)

    The performance of the implemented control algorithm is evaluated in terms of power-factor correction; load balancing, neutral source current mitigation and mitigation of voltage and current harmonics, voltage sag and swell and voltage dips in a three-phase four-wire distribution system for different combination of linear and ...

  10. Three-phase boundary length in solid-oxide fuel cells: A mathematical model

    Science.gov (United States)

    Janardhanan, Vinod M.; Heuveline, Vincent; Deutschmann, Olaf

    A mathematical model to calculate the volume specific three-phase boundary length in the porous composite electrodes of solid-oxide fuel cell is presented. The model is exclusively based on geometrical considerations accounting for porosity, particle diameter, particle size distribution, and solids phase distribution. Results are presented for uniform particle size distribution as well as for non-uniform particle size distribution.

  11. Vector control of three-phase AC/DC front-end converter

    Indian Academy of Sciences (India)

    Section 4 presents the simulation and experimental results of FEC. Section 5 discusses the problems associated with the starting process of ..... A 250-kVA vector-controlled FEC is simulated with MATLAB/SIMULINK. ..... Ghosh R 2007 Modelling, Analysis and Control of Single-phase and Three-phase PWM Rectifiers.

  12. Supporting the role of community members employed as research staff: Perspectives of community researchers working in addiction research.

    Science.gov (United States)

    True, Gala; Alexander, Leslie B; Fisher, Celia B

    2017-08-01

    Community researchers are laypersons who conduct research activities in their own communities. In addiction and HIV research, community researchers are valued for their insider status and knowledge. At the same time, their presence on the research team raises concerns about coercion and confidentiality when community researchers and participants know each other personally, and the work of navigating between the worlds of research and community leads to moral distress and burnout for some community researchers. In this paper, we draw upon the concept of 'moral experience' to explore the local moral worlds of community researchers in the context of addiction research. In February and March 2010, we conducted focus groups with 36 community researchers employed on community-based addiction studies in the United States to elicit perspectives on ethical and moral challenges they face in their work and insights on best practices to support their role in research. Community researchers described how their values were realized or thwarted in the context of research, and their strategies for coping with shifting identities and competing priorities. They delineated how their knowledge could be used to inform development of research protocols and help principal investigators build and maintain trust with the community researchers on their teams. Our findings contribute to current understandings of the moral experiences of community members employed in research, and inform policies and practices for the growing field of community-engaged research. Funders, research organizations, and research ethics boards should develop guidelines and standards to ensure studies have key resources in place to support community researchers and ensure quality and integrity of community-engaged work. Investigators who work with community researchers should ensure channels for frontline staff to provide input on research protocols and to create an atmosphere where challenges and concerns can be

  13. Neural network-based voltage regulator for an isolated asynchronous generator supplying three-phase four-wire loads

    Energy Technology Data Exchange (ETDEWEB)

    Singh, Bhim; Kasal, Gaurav Kumar [Department of Electrical Engineering, Indian Institute of Technology, Delhi, Hauz-Khas, New Delhi 110016 (India)

    2008-06-15

    This paper deals with a neural network-based solid state voltage controller for an isolated asynchronous generator (IAG) driven by constant speed prime mover like diesel engine, bio-gas or gasoline engine and supplying three-phase four-wire loads. The proposed control scheme uses an indirect current control and a fast adaptive linear element (adaline) based neural network reference current extractor, which extracts the real positive sequence current component without any phase shift. The neutral current of the source is also compensated by using three single-phase bridge configuration of IGBT (insulated gate bipolar junction transistor) based voltage source converter (VSC) along-with single-phase transformer having self-supported dc bus. The proposed controller provides the functions as a voltage regulator, a harmonic eliminator, a neutral current compensator, and a load balancer. The proposed isolated electrical system with its controller is modeled and simulated in MATLAB along with Simulink and PSB (Power System Block set) toolboxes. The simulated results are presented to demonstrate the capability of an isolated asynchronous generating system driven by a constant speed prime mover for feeding three-phase four-wire loads. (author)

  14. Direction and Policies Needed to Support Hybrid Electric Car Research

    Directory of Open Access Journals (Sweden)

    Ridwan Arief Subekti

    2012-07-01

    Full Text Available The rising number of vehicles over the years has driven the increase of air pollution and fuel consumption. One of the solutions to overcome this problem is using hybrid electric car because it is environmentally friendly and efficient in fuel consumption. LIPI has conducted electric car research since 1997, but there were so many problems in its development that electric car can not be developed into a national industry scale. Therefore, it is important to conduct a study that maps the problems and finds the solutions to prevent the same failure of electric car commercialization process from happening to hybrid electric car . This study was done by collecting and analyzing the primary and secondary data through interviews, discussing electric hybrid car with stakeholders, and examining earlier study results and regulations. Based on this study, several policies to support sustainability research of hybrid electric car were proposed. Some recommendations were the making of national roadmap and regulation for the usage of hybrid electric car on the road. For policy makers at LIPI, a research focus, research coordination, and pre-commercialization program were recommended.

  15. Support and development for remote collaborations in fusion research

    International Nuclear Information System (INIS)

    Casper, T.A.; Jong, R.A.; Meyer, W.H.; Moller, J.M.

    2000-01-01

    Major fusion experiments and modeling efforts rely on joint research of scientists from several locations around the world. A variety of software tools are in use to provide remote interactive access to facilities and data are routinely available over wide-area-network connections to researchers. Audio and video communications, monitoring of control room information and synchronization of remote sites with experimental operations all enhance participation during experiments. Remote distributed computing capabilities allow utilization of off-site computers that now help support the demands of control room analyses and plasma modeling. A collaborative software development project is currently using object technologies with CORBA-based communications to build a network executable transport code that further demonstrates the ability to utilize geographically dispersed resources. Development to extend these concepts with security and naming services and possible applications to instrumentation systems has been initiated. An Information Technology Initiative is deploying communication systems, ISDN (telephone) and IP (network) audio/video (A/V) and web browser-based, to build the infrastructure needed to support remote physics meetings, seminars and interactive discussions

  16. Support and development for remote collaboration in fusion research

    International Nuclear Information System (INIS)

    Casper, T A; Jong, R A; Meyer, W H; Moller, J M

    1999-01-01

    Major fusion experiments and modeling efforts rely on joint research of scientists from several locations around the world. A variety of software tools are in use to provide remote interactive access to facilities and data are routinely available over wide-area-network connections to researchers. Audio and video communications, monitoring of control room information and synchronization of remote sites with experimental operations all enhance participation during experiments. Remote distributed computing capabilities allow utilization of off-site computers that now help support the demands of control room analyses and plasma modeling. A collaborative software development project is currently using object technologies with CORBA-based communications to build a network executable transport code that further demonstrates the ability to utilize geographically dispersed resources. Development to extend these concepts with security and naming services and possible applications to instrumentation systems has been initiated. An Information Technology Initiative is deploying communication systems, ISDN (telephone) and IP (network) audio/video (A/V) and web browser-based, to build the infrastructure needed to support remote physics meetings, seminars and interactive discussions

  17. INFORMATION SUPPORT OF INNOVATION RESEARCH PROJECTS OF THE UNIVERSITY

    Directory of Open Access Journals (Sweden)

    Popov E. Yu.

    2015-06-01

    Full Text Available The article presents and illustrates by the example of the Novosibirsk State University a methodical approach to the development of information support of innovative research projects of the university, its historical background and their components. The basis of the external side of the approach is the system-innovative bibliometric analysis of foreign and Russian economic, scientific and technical literature. The author provides the method and the results of analysis of publication activity indicators for the sources presented in the Scientific Electronic Library (www.elibrary.ru for the period of 1991-2005 and 2006-2015 (April years. This analysis includes the specific words and word combinations included in the article title. This analysis allowed us to give a quantitative evaluation of motion vectors for universities researches and innovations. The internal side of the methodical approach includes a special system of planning, accounting and control of financial support of scientific activities of the NSU. The description of the system contains the details of historical background, patterns of interaction of participants, key documents and indicators, algorithms for cost calculation, and software. The foundation of a group of laboratories in NSU under the supervision of the world's leading scientists is considered as an important result of the proposed approach. A brief description of these laboratories is given.

  18. Nuclear Research and Development Capabilities Needed to Support Future Growth

    Energy Technology Data Exchange (ETDEWEB)

    Wham, Robert M. [ORNL, P.O. Box 2008, Oak Ridge, TN 37831-6154 (United States); Kearns, Paul [Battelle Memorial Institute (United States); Marston, Ted [Marston Consulting (United States)

    2009-06-15

    The energy crisis looming before the United States can be resolved only by an approach that integrates a 'portfolio' of options. Nuclear energy, already an important element in the portfolio, should play an even more significant role in the future as the U.S. strives to attain energy independence and reduce carbon emissions. The DOE Office of Nuclear Energy asked Battelle Memorial Institute to obtain input from the commercial power generation industry on industry's vision for nuclear energy over the next 30-50 years. With this input, Battelle was asked to generate a set of research and development capabilities necessary for DOE to support the anticipated growth in nuclear power generation. This presentation, based on the report generated for the Office of Nuclear Energy, identifies the current and future nuclear research and development capabilities required to make this happen. The capabilities support: (1) continued, safe operation of the current fleet of nuclear plants; (2) the availability of a well qualified and trained workforce; (3) demonstration of the next generation nuclear plants; (4) development of a sustainable fuel cycle; (5) advanced technologies for maximizing resource utilization and minimization of waste and (6) advanced modeling and simulation for rapid and reliable development and deployment of new nuclear technologies. In order to assure these capabilities are made available, a Strategic Nuclear Energy Capability Initiative is proposed to provide the required resources during this critical period of time. (authors)

  19. [General practice research units in Denmark: multidisciplinary research in support of practical work].

    Science.gov (United States)

    Reventlow, Susanne; Broholm, Katalin Alexa Király; Mäkelä, Marjukka

    2014-01-01

    In Denmark the general practice research units operating in connection with universities provide a home base, training and methodology support for researchers in the field from medical students to general practitioners carrying out practical work. Research issues frequently require a multidisciplinary approach and use of different kinds of materials. Problems arising from the practical work of general practitioners take priority in the wide selection of topics. The units have networked efficiently with organizations of general practitioners and medical education. The combination of research environments has created synergy benefiting everybody and increased the scientific productivity and visibility of the field.

  20. A plan for research by the atmospheric research section in support of Ontario Hydro's nuclear activities

    International Nuclear Information System (INIS)

    Ogram, G.L.; Melo, O.T.

    1984-01-01

    A plan for nuclear studies by the Atmospheric Research Section is presented. The need for research is discussed and research objectives are established. Recommended research activities include the study of fundamental processes governing the fate of emissions released to the atmosphere by Hydro's nuclear facilities and the development of improved transport models describing the fate of these emissions. A Sectional goal of providing technical expertise in the atmospheric sciences in support of Ontario Hydro's present and future nuclear activities is proposed. The plan covers a five-year time frame (1984-1988)

  1. New three-phase ac-ac converter incorporating three-phase boost integrated ZVT bridge and single-phase HF link

    International Nuclear Information System (INIS)

    Abdelhamid, Tamer H.; Sabzali, Ahmad J.

    2008-01-01

    This paper presents a new zero voltage transition (ZVT), power factor corrected three phase ac-ac converter with single phase high frequency (HF) link. It is a two stage converter; the first stage is a boost integrated bridge converter (combination of a 3 ph boost converter and a bridge converter) operated at fixed frequency and that operates in two modes at ZVT for all switches and establishes a 1 ph square wave HF link. The second stage is a bi-directional pulse width modulation (PWM) 3 ph bridge that converts the 1 ph HF link to a 3 ph voltage using a novel switching strategy. The converter modes of operation and key equations are outlined. Simulation of the overall system is conducted using Simulink. The switching strategy and its corresponding control circuit are clearly described. Experimental verification of the simulation is conducted for a prototype of 100 V, 500 W at 10 kHz link frequency

  2. The method for simultaneous extraction and back extraction in liquid three-phase system and equipment for simultaneous extraction and back extraction in liquid three-phase system

    International Nuclear Information System (INIS)

    Palyska, W.; Chmielewski, A.G.

    1992-01-01

    The method for simultaneous extraction and back extraction in liquid three-phase system has been worked out. The equipment designed for that process has been also subject of the patent. The interesting component is extracted first to intermediate phase consists of magnetic solvent keeping two extracting phases separately. The intermediate magnetic liquid has been kept in its position using a stable magnet maintained on the surface of the extraction vessel. Then the component pass from intermediate phase to the third phase as a result of back extraction. Mixing in the extraction and back extraction zones is organized by means of rotating shaft going along the whole apparatus. The extraction and back extraction processes occur simultaneously as a result of continuous flow of solvent in their zones. The single extraction back extraction facilities can be joined in larger batteries. 3 figs

  3. Three-Phase Multistage System (DC-AC-DC-AC for Connecting Solar Cells to the Grid

    Directory of Open Access Journals (Sweden)

    Mahmudreza Changizian

    2017-11-01

    Full Text Available Inverter systems that feed electrical power from photovoltaic (PV system into the grid must convert the direct current of the PV array into the alternating current of the grid. In many applications, it is important for a converter to be lightweight, highly reliable, input/output isolated, flexible and operable in a boost mode. These features can be achieved by using a High-Frequency inverter which involves an isolated DC-DC stage and DC-AC section, which provides AC output. This paper proposes a new three phase topology, based on multi stage converter and PV system in order to use in medium and high power applications. The Perturb and Observe (P&O method is used for maximum power point tracking (MPPT control of PV array. The switching control signals for three-phase inverter are provided by hysteresis control method. Also, the comparison between the proposed topology and traditional structures has been conducted and finally the simulation researches are performed in a closed-loop control system by MATLAB/Simulink software to verify the operation of the proposed structure. The results represent better performance of the introduced system over traditional topologies.

  4. Design and Development of Gas-Liquid Cylindrical Cyclone Compact Separators for Three-Phase Flow; SEMIANNUAL

    International Nuclear Information System (INIS)

    Mohan, Ram S.; Shoham, Ovadia

    1999-01-01

    The objective of this five-year project (October, 1997-September, 2002) is to expand the current research activities of Tulsa University Separation Technology Projects (TUSTP) to multiphase oil/water/gas separation. This project will be executed in two phases. Phase I (1997-2000) will focus on the investigations of the complex multiphase hydrodynamic flow behavior in a three-phase Gas-Liquid Cylindrical Cyclone (GLCC) Separator. The activities of this phase will include the development of a mechanistic model, a computational fluid dynamics (CFD) simulator, and detailed experimentation on the three-phase GLCC. The experimental and CFD simulation results will be suitably integrated with the mechanistic model. In Phase II (2000-2002), the developed GLCC separator will be tested under high pressure and real crudes conditions. This is crucial for validating the GLCC design for field application and facilitating easy and rapid technology deployment. Design criteria for industrial applications will be developed based on these results and will be incorporated into the mechanistic model by TUSTP

  5. AuScope research infrastructure - supporting Australian mineral discovery

    Science.gov (United States)

    McInnes, B.; Rawling, T.

    2016-12-01

    Earth and geospatial scientists are heavy users of data products. When industry geologists access spatial data from the field and the exploration office they require data products that are discoverable, searchable, interoperable and attributed with robust metadata. Over the last decade AuScope has utilised NCRIS funding to provide a variety of data products including geophysical data (reflection and passive seismic, magnetotellurics and gravity), GIS layers from state and national geological survey organisations, hyperspectral core logging (National Virtual Core Library) and time-series geospatial data from GNSS and VLBI instruments - all delivered using AuScope GRID technologies based on the Spatial Information Services Stack (SiSS). Perhaps one of the best examples of collaboration to deliver data products to industry users is the National Mineral Library. Working with researchers at Curtin Universities John de Laeter Centre and ANDS, AuScope has also supported the development of a Laboratory Information Management System (LIMS). The project has produced an entirely new workflow, based around a TESCAN TIMA field emission scanning electron microscope, that allows metadata to be collected and recorded from the sample collection and preparation right through to data delivery and publication. This process has facilitated the scanning of a large stockpile of mineral samples from across Western Australia that will produce a state-wide Mineral Library, allowing mineral explorers to better understand the composition of critical rock outcrop samples from all over the state. This new NCRIS supported initiative provides a dataset that underpins both academic and applied research programs and is important for the economic future of Australia. Mining companies do a lot of heavy mineral analysis in research and development but, because there isn't a baseline for mineralogy across each state, it is difficult to have full confidence in the heavy mineral data. This creates an

  6. Evidence-informed health policy 1 - synthesis of findings from a multi-method study of organizations that support the use of research evidence.

    Science.gov (United States)

    Lavis, John N; Oxman, Andrew D; Moynihan, Ray; Paulsen, Elizabeth J

    2008-12-17

    Organizations have been established in many countries and internationally to support the use of research evidence by producing clinical practice guidelines, undertaking health technology assessments, and/or directly supporting the use of research evidence in developing health policy on an international, national, and state or provincial level. Learning from these organizations can reduce the need to 'reinvent the wheel' and inform decisions about how best to organize support for such organizations, particularly in low- and middle-income countries (LMICs). We undertook a multi-method study in three phases - a survey, interviews, and case descriptions that drew on site visits - and in each of the second and third phases we focused on a purposive sample of those involved in the previous phase. We used the seven main recommendations that emerged from the advice offered in the interviews to organize much of the synthesis of findings across phases and methods. We used a constant comparative method to identify themes from across phases and methods. Seven recommendations emerged for those involved in establishing or leading organizations that support the use of research evidence in developing health policy: 1) collaborate with other organizations; 2) establish strong links with policymakers and involve stakeholders in the work; 3) be independent and manage conflicts of interest among those involved in the work; 4) build capacity among those working in the organization; 5) use good methods and be transparent in the work; 6) start small, have a clear audience and scope, and address important questions; and 7) be attentive to implementation considerations, even if implementation is not a remit. Four recommendations emerged for the World Health Organization (WHO) and other international organizations and networks: 1) support collaborations among organizations; 2) support local adaptation efforts; 3) mobilize support; and 4) create global public goods. This synthesis of

  7. Evidence-informed health policy 1 – Synthesis of findings from a multi-method study of organizations that support the use of research evidence

    Directory of Open Access Journals (Sweden)

    Moynihan Ray

    2008-12-01

    Full Text Available Abstract Background Organizations have been established in many countries and internationally to support the use of research evidence by producing clinical practice guidelines, undertaking health technology assessments, and/or directly supporting the use of research evidence in developing health policy on an international, national, and state or provincial level. Learning from these organizations can reduce the need to 'reinvent the wheel' and inform decisions about how best to organize support for such organizations, particularly in low- and middle-income countries (LMICs. Methods We undertook a multi-method study in three phases – a survey, interviews, and case descriptions that drew on site visits – and in each of the second and third phases we focused on a purposive sample of those involved in the previous phase. We used the seven main recommendations that emerged from the advice offered in the interviews to organize much of the synthesis of findings across phases and methods. We used a constant comparative method to identify themes from across phases and methods. Results Seven recommendations emerged for those involved in establishing or leading organizations that support the use of research evidence in developing health policy: 1 collaborate with other organizations; 2 establish strong links with policymakers and involve stakeholders in the work; 3 be independent and manage conflicts of interest among those involved in the work; 4 build capacity among those working in the organization; 5 use good methods and be transparent in the work; 6 start small, have a clear audience and scope, and address important questions; and 7 be attentive to implementation considerations, even if implementation is not a remit. Four recommendations emerged for the World Health Organization (WHO and other international organizations and networks: 1 support collaborations among organizations; 2 support local adaptation efforts; 3 mobilize support; and 4 create

  8. Fracture healing: Quantitative three-phase bone scintigraphy as a prognostic factor

    International Nuclear Information System (INIS)

    Dodig, D.; Kasal, B.; Kragic-Pranic, A.; Predic, P.

    2002-01-01

    Aim: Careful clinical examination and conventional radiography, together with other standard methods for evaluation of bone fracture healing, are frequently inconclusive. Furthermore, it is difficult to predict the complications of healing on the basis of clinical and radiographic findings only. Bone scintigraphy plays an important role in detecting bone fractures. This method is very sensitive, but not enough specific. The aim of this work was to evaluate the role of three-phase bone scintigraphy in the healing prognosis of long bone fractures. Material and Methods: We evaluated the three elements (perfusion, blood pool and static image) of three-phase bone scintigraphy in early prognosis of the course of fracture healing in patients with fractures of femur or tibia. Three-phase bone scintigraphy was performed in 73 patients. The patients were divided into 4 groups according to X-ray and clinical examination: 1) Non operated patients with stable fracture, 2) Operated patients with unstable fracture (infection), 3) Fractures with delayed union, 4) Patients with pseudoarthrosis. Using region of interest (ROI) method we compared the activity on the site of fracture with the activity on the symmetrical place in the healthy bone. The relative indices for each group of patients and for each element of three-bone scintigraphy were calculated in order to make possible the follow up of the fracture healing and to obtain data for prognosis and evaluation of possible complications. Results: The most valuable results were obtained by quantitative analysis of perfusion data immediately after trauma and 2-3 weeks later. Our results show a high diagnostic accuracy in identifying infection by perfusion scintigrams immediately after trauma. The perfusion indices obtained immediately and after 2-3 weeks could predict delayed union after the trauma. Quantitative analysis of blood pool phase gave no data of clinical significance in distinguishing various pathologies. Conclusion: Our

  9. [Partnership-based research as a space to support innovation].

    Science.gov (United States)

    Bernier, Jocelyne

    2014-03-01

    The process of joint evaluation involving several actors is criss-crossed by a process of negotiation and adjustment between different concerns, responsibilities and interests. How can we encourage a dialogue between knowledge from expertise and knowledge from experience, in order to produce knowledge that is scientifically based and useful for those who are involved in the programs? Far from being a mechanical process, this involves the delicate task of striking a balance, which relies on a negotiated partnership framework. The implementation of an advisory committee, organized by an interface function between the stakeholders of the intervention under study, has increasingly become recognized as a necessary condition for success in partnership-based research. These conditions enable the deployment of a reflexive system that can support social innovation--when the formulation of the problem and its resulting actions become enriched, as knowledge about the intervention develops.

  10. Electrostatic Levitation: A Tool to Support Materials Research in Microgravity

    Science.gov (United States)

    Rogers, Jan; SanSoucie, Mike

    2012-01-01

    Containerless processing represents an important topic for materials research in microgravity. Levitated specimens are free from contact with a container, which permits studies of deeply undercooled melts, and high-temperature, highly reactive materials. Containerless processing provides data for studies of thermophysical properties, phase equilibria, metastable state formation, microstructure formation, undercooling, and nucleation. The European Space Agency (ESA) and the German Aerospace Center (DLR) jointly developed an electromagnetic levitator facility (MSL-EML) for containerless materials processing in space. The electrostatic levitator (ESL) facility at the Marshall Space Flight Center provides support for the development of containerless processing studies for the ISS. Apparatus and techniques have been developed to use the ESL to provide data for phase diagram determination, creep resistance, emissivity, specific heat, density/thermal expansion, viscosity, surface tension and triggered nucleation of melts. The capabilities and results from selected ESL-based characterization studies performed at NASA's Marshall Space Flight Center will be presented.

  11. Fundamental research of decision support systems: Final report

    International Nuclear Information System (INIS)

    Kurstedt, H.A. Jr.

    1986-01-01

    Through an iterative application of Decision Support Systems (DSS) apparatus and evolution of DSS concepts, we redefined DSS from a systems perspective. By focusing on successful DSS and the definition of success for the newly-defined DSS, we generated a paradigm for understanding, applying, and improving DSS. The significance of the research is that we now: (1) understand the various roles management tools play within the new DSS concept; (2) recognize the need for characterizing the domain of responsibility of a manager to obtain a successful DSS; and (3) have learned special characteristics of government agencies like Nuclear Materials (NM) to identify what features of the new DSS concept can be expected to improve performance

  12. CLOUD EDUCATIONAL RESOURCES FOR PHYSICS LEARNING RESEARCHES SUPPORT

    Directory of Open Access Journals (Sweden)

    Oleksandr V. Merzlykin

    2015-10-01

    Full Text Available The definition of cloud educational resource is given in paper. Its program and information components are characterized. The virtualization as the technological ground of transforming from traditional electronic educational resources to cloud ones is reviewed. Such levels of virtualization are described: data storage device virtualization (Data as Service, hardware virtualization (Hardware as Service, computer virtualization (Infrastructure as Service, software system virtualization (Platform as Service, «desktop» virtualization (Desktop as Service, software user interface virtualization (Software as Service. Possibilities of designing the cloud educational resources system for physics learning researches support taking into account standards of learning objects metadata (accessing via OAI-PMH protocol and standards of learning tools interoperability (LTI are shown. The example of integration cloud educational resources into Moodle learning management system with use of OAI-PMH and LTI is given.

  13. The Need for District Support for School Reform: What the Researchers Say. Research Brief.

    Science.gov (United States)

    Appelbaum, Deborah

    This article focuses on the school district's role in implementing Comprehensive School Reform (CSR). Research shows that effective district support for CSR varies from district to district. This is due, in part, to the fact that many prior models bypassed the district, operating under the belief that reform would be more effective if it targeted…

  14. LCL filter design for three-phase two-level power factor correction using line impedance stabilization network

    DEFF Research Database (Denmark)

    Kouchaki, Alireza; Nymand, Morten

    2016-01-01

    This paper presents LCL filter design method for three-phase two-level power factor correction (PFC) using line impedance stabilization network (LISN). A straightforward LCL filter design along with variation in grid impedance is not simply achievable and inevitably lead to an iterative solution...... for filter. By introducing of fast power switches for PFC applications such as silicon-carbide, major current harmonics around the switching frequency drops in the region that LISN can actively provide well-defined impedance for measuring the harmonics (i.e. 9 kHz- 30MHz). Therefore, LISN can be replaced...... is derived using the current ripple behavior of converter-side inductor. The grid-side inductor is achieved as a function of LISN impedance to fulfill the grid regulation. To verify the analyses, an LCL filter is designed for a 5 kW SiC-based PFC. The simulation and experimental results support the validity...

  15. Catalytic wet-air oxidation of lignin in a three-phase reactor with aromatic aldehyde production

    Directory of Open Access Journals (Sweden)

    Sales F.G.

    2004-01-01

    Full Text Available In the present work a process of catalytic wet air oxidation of lignin obtained from sugar-cane bagasse is developed with the objective of producing vanillin, syringaldehyde and p-hydroxybenzaldehyde in a continuous regime. Palladium supported on g-alumina was used as the catalyst. The reactions in the lignin degradation and aldehyde production were described by a kinetic model as a system of complex parallel and series reactions, in which pseudo-first-order steps are found. For the purpose of producing aromatic aldehydes in continuous regime, a three-phase fluidized reactor was built, and it was operated using atmospheric air as the oxidizer. The best yield in aromatic aldehydes was of 12%. The experimental results were compatible with those values obtained by the pseudo-heterogeneous axial dispersion model (PHADM applied to the liquid phase.

  16. The Design of Connection Solid Oxide Fuel Cell (SOFC) Integrated Grid with Three-Phase Inverter

    Science.gov (United States)

    Darjat; Sulistyo; Triwiyatno, Aris; Thalib, Humaid

    2018-03-01

    Fuel cell technology is a relatively new energy-saving technology that has the potential to replace conventional energy technologies. Among the different types of generation technologies, fuel cells is the generation technologies considered as a potential source of power generation because it is flexible and can be placed anywhere based distribution system. Modeling of SOFC is done by using Nernst equation. The output power of the fuel cell can be controlled by controlling the flow rate of the fuels used in the process. Three-phase PWM inverter is used to get the form of three-phase voltage which same with the grid. In this paper, the planning and design of the SOFC are connected to the grid.

  17. Three phase heat and mass transfer model for unsaturated soil freezing process: Part 2 - model validation

    Science.gov (United States)

    Zhang, Yaning; Xu, Fei; Li, Bingxi; Kim, Yong-Song; Zhao, Wenke; Xie, Gongnan; Fu, Zhongbin

    2018-04-01

    This study aims to validate the three-phase heat and mass transfer model developed in the first part (Three phase heat and mass transfer model for unsaturated soil freezing process: Part 1 - model development). Experimental results from studies and experiments were used for the validation. The results showed that the correlation coefficients for the simulated and experimental water contents at different soil depths were between 0.83 and 0.92. The correlation coefficients for the simulated and experimental liquid water contents at different soil temperatures were between 0.95 and 0.99. With these high accuracies, the developed model can be well used to predict the water contents at different soil depths and temperatures.

  18. Three-phase receiving coil of wireless power transmission system for gastrointestinal robot

    Science.gov (United States)

    Jia, Z. W.; Jiang, T.; Liu, Y.

    2017-11-01

    Power shortage is the bottleneck for the wide application of gastrointestinal (GI) robot. Owing to the limited volume and free change of orientation of the receiving set in GI trace, the optimal of receiving set is the key point to promote the transmission efficiency of wireless power transmission system. A new type of receiving set, similar to the winding of three-phase asynchronous motor, is presented and compared with the original three-dimensional orthogonal coil. Considering the given volume and the space utilization ratio, the three-phase and the three-orthogonal ones are the parameters which are optimized and compared. Both the transmission efficiency and stability are analyzed and verified by in vitro experiments. Animal experiments show that the new one could provide at least 420 mW power in volume of Φ11 × 13mm with a uniformity of 78.3% for the GI robot.

  19. A Novel Concept for Three-Phase Cascaded Multilevel Inverter Topologies

    Directory of Open Access Journals (Sweden)

    Md Mubashwar Hasan

    2018-01-01

    Full Text Available One of the key challenges in multilevel inverters (MLIs design is to reduce the number of components used in the implementation while maximising the number of output voltage levels. This paper proposes a new concept that facilitates a device count reduction technique of existing cascaded MLIs. Moreover, the proposed concept can be utilised to extend existing single phase cascaded MLI topologies to three-phase structure without tripling the number of semiconductor components and input dc-supplies as per the current practice. The new generalized concept involves two stages; namely, cascaded stage and phase generator stage. The phase generator stage is a combination of a conventional three-phase two level inverter and three bi-directional switches while the cascaded stage can employ any existing cascaded topology. A laboratory prototype model is built and extensive experimental analyses are conducted to validate the feasibility of the proposed cascaded MLI concept.

  20. Role of three-phase bone scintigraphy in therapy of lower extremity infections

    International Nuclear Information System (INIS)

    Grund, F.M.; Larson, B.W.; Sinn, L.M.; Peterson, L.R.

    1990-01-01

    This paper evaluates the ability of three-phase bone scintigraphy to predict the need for prolonged antibiotic therapy and assess results of therapy of lower extremity infections in patients with diabetes mellitus and/or peripheral vascular disease. The authors retrospectively reviewed three-phase bone scans from 39 patients who completed either 3 weeks or 3 months of oral ciprofloxacin based on initial clinical and radiologic impression. bone scans were obtained at diagnosis and 1 year later. IN 31 patients, increased focal activity was shown on the delayed images. Nineteen of 25 were successfully treated with 3 months of antibiotics, but only one of six were successfully treated with 3 weeks of antibiotics. Eight patient showed no focal increased uptake on delayed images, and seven of these were successfully treated with 3 weeks of antibiotics

  1. A novel method to augment extraction of mangiferin by application of microwave on three phase partitioning.

    Science.gov (United States)

    Kulkarni, Vrushali M; Rathod, Virendra K

    2015-06-01

    This work reports a novel approach where three phase partitioning (TPP) was combined with microwave for extraction of mangiferin from leaves of Mangifera indica . Soxhlet extraction was used as reference method, which yielded 57 mg/g in 5 h. Under optimal conditions such as microwave irradiation time 5 min, ammonium sulphate concentration 40% w/v, power 272 W, solute to solvent ratio 1:20, slurry to t -butanol ratio 1:1, soaking time 5 min and duty cycle 50%, the mangiferin yield obtained was 54 mg/g by microwave assisted three phase partitioning extraction (MTPP). Thus extraction method developed resulted into higher extraction yield in a shorter span, thereby making it an interesting alternative prior to down-stream processing.

  2. A novel method to augment extraction of mangiferin by application of microwave on three phase partitioning

    Directory of Open Access Journals (Sweden)

    Vrushali M. Kulkarni

    2015-06-01

    Full Text Available This work reports a novel approach where three phase partitioning (TPP was combined with microwave for extraction of mangiferin from leaves of Mangifera indica. Soxhlet extraction was used as reference method, which yielded 57 mg/g in 5 h. Under optimal conditions such as microwave irradiation time 5 min, ammonium sulphate concentration 40% w/v, power 272 W, solute to solvent ratio 1:20, slurry to t-butanol ratio 1:1, soaking time 5 min and duty cycle 50%, the mangiferin yield obtained was 54 mg/g by microwave assisted three phase partitioning extraction (MTPP. Thus extraction method developed resulted into higher extraction yield in a shorter span, thereby making it an interesting alternative prior to down-stream processing.

  3. Three Phase Power Imbalance Decomposition into Systematic Imbalance and Random Imbalance

    DEFF Research Database (Denmark)

    Kong, Wangwei; Ma, Kang; Wu, Qiuwei

    2017-01-01

    Uneven load allocations and random load behaviors are two major causes for three-phase power imbalance. The former mainly cause systematic imbalance, which can be addressed by low-cost phase swapping; the latter contribute to random imbalance, which requires relatively costly demand...... minimum phase, or both. Then, this paper proposes a new method to decompose three-phase power series into a systematic imbalance component and a random imbalance component as the closed-form solutions of quadratic optimization models that minimize random imbalance. A degree of power imbalance...... is calculated based on the systematic imbalance component to guide phase swapping. Case studies demonstrate that 72.8% of 782 low voltage substations have systematic imbalance components. The degree of power imbalance results reveal the maximum need for phase swapping and the random imbalance components reveal...

  4. An animal experimental study of transient synovitis of hip using three phase bone imaging

    International Nuclear Information System (INIS)

    Liang Jiugen; Lu Bing; Lu Xiaohu; Liu Shangli

    1994-01-01

    A model of transient synovitis was established by means of injecting noradrenaline (NA) into the joint cavity of young dogs. Radionuclide three phase bone imaging was then used to observe the local blood supply of femoral head and histological examination was used to understand the natural course of the disease process. The result showed that there were transient synovitis of the hip and decrease of blood supply in the affected femoral head after NA injection, but the changes gradually returned to normal after 4 weeks. No evidence of femoral head necrosis had been noticed. It is suggested that serial quantitative analysis of three phase bone imaging may have good clinical value in the early diagnosis transient hip synovitis, as well as in the assessment of the stage of the disease etc

  5. Dynamic\tmodelling of catalytic three-phase reactors for hydrogenation and oxidation processes

    Directory of Open Access Journals (Sweden)

    Salmi T.

    2000-01-01

    Full Text Available The dynamic modelling principles for typical catalytic three-phase reactors, batch autoclaves and fixed (trickle beds were described. The models consist of balance equations for the catalyst particles as well as for the bulk phases of gas and liquid. Rate equations, transport models and mass balances were coupled to generalized heterogeneous models which were solved with respect to time and space with algorithms suitable for stiff differential equations. The aspects of numerical solution strategies were discussed and the procedure was illustrated with three case studies: hydrogenation of aromatics, hydrogenation of aldehydes and oxidation of ferrosulphate. The case studies revealed the importance of mass transfer resistance inside the catalyst pallets as well as the dynamics of the different phases being present in the reactor. Reliable three-phase reactor simulation and scale-up should be based on dynamic heterogeneous models.

  6. Analysis of Three-Phase Rectifier Systems with Controlled DC-Link Current Under Unbalanced Grids

    DEFF Research Database (Denmark)

    Kumar, Dinesh; Davari, Pooya; Zare, Firuz

    2017-01-01

    Voltage unbalance is the most common disturbance in distribution networks, which give undesirable effects on many grid connected power electronics systems including Adjustable Speed Drive (ASD). Severe voltage unbalance can force three-phase rectifiers into almost single-phase operation, which...... degrades the grid power quality and also imposes a significant negative impact on the ASD system. This major power quality issue affecting the conventional rectifiers can be attenuated by controlling the DC-link current based on an Electronic Inductor (EI) technique. The purpose of this digest...... is to analyze and compare the performance of an EI with a conventional three-phase rectifier under unbalanced grid conditions. Experimental and simulation results validate the proposed mathematical modelling. Further analysis and benchmarking will be provided in the final paper....

  7. A modified two-level three-phase quasi-soft-switching inverter

    DEFF Research Database (Denmark)

    Liu, Yusheng; Wu, Weimin; Blaabjerg, Frede

    2014-01-01

    A traditional Voltage Source Inverter (VSI) has higher efficiency than a Current Voltage Source (CSI) due to the less conduction power loss. However, the reverse recovery of the free-wheeling diode limits the efficiency improvement for the silicon devices based hard-switching VSI. The traditional...... quasi-soft-switching inverter can alternate between VSI and CSI by using a proper control scheme and thereby reduce the power losses caused by the reverse recovery of the free-wheeling diode. Nevertheless, slightly extra conduction power loss of the auxiliary switch is also introduced. In order...... to reduce the extra conduction power loss and the voltage stress across the DC-link capacitor, a modified two-level three-phase quasi-soft-switching inverter is proposed by using a SiC MOSFET instead of an IGBT. The principle of the modified two-level three-phase quasi-soft-switching inverter is analyzed...

  8. Improved control strategy for the three-phase grid-connected inverter

    DEFF Research Database (Denmark)

    Yao, Zhilei; Xiao, Lan; Guerrero, Josep M.

    2015-01-01

    An improved control strategy for the three-phase grid-connected inverter with space vector pulse width modulation (SVPWM) is proposed. When the grid current contains harmonics, the d- and q-axis grid currents will be interacted, and then the waveform quality of the grid current will be poorer....... As the reference output voltage cannot directly reflect the change of the reference grid current, the dynamic response of the grid-connected inverter is slow. In order to solve the aforementioned problems, the d- and q-axis grid currents in the decoupled components of the grid current controller can be substituted...... by the d- and q-axis reference grid currents, respectively. The operating principles of the traditional and proposed control methods are illustrated. Experimental results for a 15-kVA three-phase grid-connected inverter with SVPWM verify the theoretical analysis. Compared with the traditional control...

  9. Analysis of three-phase power-supply systems using computer-aided design programs

    International Nuclear Information System (INIS)

    Oberst, E.F.

    1977-01-01

    A major concern of every designer of large, three-phase power-supply systems is the protection of system components from overvoltage transients. At present, three computer-aided circuit design programs are available in the Magnetic Fusion Energy (MFE) National Computer Center that can be used to analyze three-phase power systems: MINI SCEPTRE, SPICE I, and SPICE II. These programs have been used at Lawrence Livermore Laboratory (LLL) to analyze the operation of a 200-kV dc, 20-A acceleration power supply for the High Voltage Test Stand. Various overvoltage conditions are simulated and the effectiveness of system protective devices is observed. The simulated overvoltage conditions include such things as circuit breaker openings, pulsed loading, and commutation voltage surges in the rectifiers. These examples are used to illustrate the use of the computer-aided, circuit-design programs discussed in this paper

  10. A TECHNIQUE OF IDENTIFICATION OF THE PHASE-DISPLACEMENT GROUP OF THREE-PHASE TRANSFORMER

    International Nuclear Information System (INIS)

    Aburjania, A.; Begiashvili, V.; Rezan Turan

    2007-01-01

    It is demonstrated that the arbitrary choice of arbitrarily pisitive direction of induced currents and voltages contradicts the energy conservation law and leads to equilibrium equations and standards making no sense from the physical standpoint. Of 12 recognized standard phase-displacement groups of three-phase transformer, only three have real physical bases. The rest are based on a wrong assumption about mutual biasing of primary and secondary currents. They does not rule out the occurrence of emergency situations and, thus, must be eliminated from use. A new method of identification of the phase-displacement of three-phase transformer is proposed. The method is based on well-known physical laws with consideration for the dual character of the inertia of mutual inductance and exhausts for all possible versions of connection of transformer windings. (author)

  11. Performance Analysis of Three-Phase Induction Motor with AC Direct and VFD

    Science.gov (United States)

    Kumar, Dinesh

    2018-03-01

    The electrical machine analysis and performance calculation is a very important aspect of efficient drive system design. The development of power electronics devices and power converters provide smooth speed control of Induction Motors by changing the frequency of input supply. These converters, on one hand are providing a more flexible speed control that also leads to problems of harmonics and their associated ailments like pulsating torque, distorted current and voltage waveforms, increasing losses etc. This paper includes the performance analysis of three phase induction motor with three-phase AC direct and variable frequency drives (VFD). The comparison has been concluded with respect to various parameters. MATLAB-SIMULINKTM is used for the analysis.

  12. Voltage unbalance mitigation in LV networks using three-phase PV systems

    DEFF Research Database (Denmark)

    Garcia Bajo, Cristina; Hashemi Toghroljerdi, Seyedmostafa; Bækhøj Kjær, Søren

    2015-01-01

    In this paper a new method is proposed to mitigate voltage unbalance caused by single-phase solar inverters in low voltage (LV) networks. The method is based on uneven reactive power absorption and injection by three-phase solar inverters. Independent control of each phase is performed to achieve...... this uneven injection. The average values of phase voltages at the connection points of the photovoltaic (PV) inverters are used as the references for the balancing algorithm. Voltage unbalance mitigation is achieved by use of this method in different scenarios with variable three-phase and single......-phase inverters penetration in a realistic LV grid. In addition, the overvoltage is reduced by using this method....

  13. Voltage harmonic variation in three-phase induction motors with different coil pitches

    International Nuclear Information System (INIS)

    Deshmukh, Ram; Moses, Anthony John; Anayi, Fatih

    2006-01-01

    A pulse-width modulation (PWM) inverter feeding four different chorded three-phase induction motors was tested for low-order odd harmonic voltage component and efficiency at different loads. Total harmonic distortion (THD) due to 3rd, 5th and 9th harmonics was less in a motor with 160 o coil pitch. Particular harmonic order for each coil pitch was suppressed and the efficiency of a 120 o coil pitch motor was increased by 7.5%

  14. A variable frequency three phase inverter for use with Philips cryogenerators

    International Nuclear Information System (INIS)

    Carter, R.C.

    1977-10-01

    This report describes a solid state inverter designed to power the helium circulators on the cryogenerators used on the Rapid Cycling Vertex Detector at the Rutherford Laboratory. In these cryogenerators cold helium is pumped around the refrigeration loop by a small three phase induction motor. The motor requires a supply of 220 volts, 40 mA per phase, and varying in frequency between 200 and 300 Hz, depending on the length and general characteristics of the loop and transfer line. (author)

  15. Controlling a Four-Quadrant Brushless Three-Phase dc Motor

    Science.gov (United States)

    Nola, F. J.

    1986-01-01

    Control circuit commutates windings of brushless, three-phase, permanent-magnet motor operating from power supply. With single analog command voltage, controller makes motor accelerate, drive steadily, or brake regeneratively, in clockwise or counterclockwise direction. Controller well suited for use with energy-storage flywheels, actuators for aircraft-control surfaces, cranes, industrial robots, and other electromechanical systems requiring bidirectional control or sudden stopping and reversal.

  16. Three-phase boundary length in solid-oxide fuel cells: A mathematical model

    Energy Technology Data Exchange (ETDEWEB)

    Janardhanan, Vinod M. [Institutefor Chemical Technology and Polymer Chemistry, University of Karlsruhe (TH), Kaiserstr. 12, D-76128 Karlsruhe (Germany); Heuveline, Vincent; Deutschmann, Olaf [Institute for Applied and Numerical Mathematics, University of Karlsruhe (TH), Kaiserstr. 12, D-76128 Karlsruhe (Germany)

    2008-03-15

    A mathematical model to calculate the volume specific three-phase boundary length in the porous composite electrodes of solid-oxide fuel cell is presented. The model is exclusively based on geometrical considerations accounting for porosity, particle diameter, particle size distribution, and solids phase distribution. Results are presented for uniform particle size distribution as well as for non-uniform particle size distribution. (author)

  17. An Integrated Inductor For Parallel Interleaved Three-Phase Voltage Source Converters

    DEFF Research Database (Denmark)

    Gohil, Ghanshyamsinh Vijaysinh; Bede, Lorand; Teodorescu, Remus

    2016-01-01

    Three phase Voltage Source Converters (VSCs) are often connected in parallel to realize high current output converter system. The harmonic quality of the resultant switched output voltage can be improved by interleaving the carrier signals of these parallel connected VSCs. As a result, the line...... of the state-of-the-art filtering solution. The performance of the integrated inductor is also verified by the experimental measurements....

  18. Investigation on Capacitor Switching Transient Limiter with a Three phase Variable Resistance

    DEFF Research Database (Denmark)

    Naderi, Seyed Behzad; Jafari, Mehdi; Zandnia, Amir

    2017-01-01

    In this paper, a capacitor switching transient limiter based on a three phase variable resistance is proposed. The proposed structure eliminates the capacitor switching transient current and over-voltage by introducing a variable resistance to the current path with its special switching pattern...... transients on capacitor after bypassing. Analytic Analyses for this structure in transient cases are presented in details and simulations are performed by MATLAB software to prove its effectiveness....

  19. Design of materials with extreme thermal expansion using a three-phase topology optimization method

    DEFF Research Database (Denmark)

    Sigmund, Ole; Torquato, S.

    1997-01-01

    Composites with extremal or unusual thermal expansion coefficients are designed using a three-phase topology optimization method. The composites are made of two different material phases and a void phase. The topology optimization method consists in finding the distribution of material phases...... materials having maximum directional thermal expansion (thermal actuators), zero isotropic thermal expansion, and negative isotropic thermal expansion. It is shown that materials with effective negative thermal expansion coefficients can be obtained by mixing two phases with positive thermal expansion...

  20. Supporting open access to clinical trial data for researchers: The Duke Clinical Research Institute-Bristol-Myers Squibb Supporting Open Access to Researchers Initiative.

    Science.gov (United States)

    Pencina, Michael J; Louzao, Darcy M; McCourt, Brian J; Adams, Monique R; Tayyabkhan, Rehbar H; Ronco, Peter; Peterson, Eric D

    2016-02-01

    There are growing calls for sponsors to increase transparency by providing access to clinical trial data. In response, Bristol-Myers Squibb and the Duke Clinical Research Institute have collaborated on a new initiative, Supporting Open Access to Researchers. The aim is to facilitate open sharing of Bristol-Myers Squibb trial data with interested researchers. Key features of the Supporting Open Access to Researchers data sharing model include an independent review committee that ensures expert consideration of each proposal, stringent data deidentification/anonymization and protection of patient privacy, requirement of prespecified statistical analysis plans, and independent review of manuscripts before submission for publication. We believe that these approaches will promote open science by allowing investigators to verify trial results as well as to pursue interesting secondary uses of trial data without compromising scientific integrity. Copyright © 2015 Elsevier Inc. All rights reserved.

  1. Physics of automated driving in framework of three-phase traffic theory.

    Science.gov (United States)

    Kerner, Boris S

    2018-04-01

    We have revealed physical features of automated driving in the framework of the three-phase traffic theory for which there is no fixed time headway to the preceding vehicle. A comparison with the classical model approach to automated driving for which an automated driving vehicle tries to reach a fixed (desired or "optimal") time headway to the preceding vehicle has been made. It turns out that automated driving in the framework of the three-phase traffic theory can exhibit the following advantages in comparison with the classical model of automated driving: (i) The absence of string instability. (ii) Considerably smaller speed disturbances at road bottlenecks. (iii) Automated driving vehicles based on the three-phase theory can decrease the probability of traffic breakdown at the bottleneck in mixed traffic flow consisting of human driving and automated driving vehicles; on the contrary, even a single automated driving vehicle based on the classical approach can provoke traffic breakdown at the bottleneck in mixed traffic flow.

  2. A three-phase comprehensive mathematical model of desulfurization in electroslag remelting process

    International Nuclear Information System (INIS)

    Wang, Qiang; Li, Guangqiang; He, Zhu; Li, Baokuan

    2017-01-01

    Highlights: • First developed a three-phase coupled model of desulfurization in ESR process. • The MHD thermal flow in the reactor was clarified. • Distributions of sulfur concentration in the three phases were demonstrated. • An experiment was carried out to validate the simulation. - Abstract: A three-phase comprehensive mathematical model has been established to study the desulfurization behavior in electroslag remelting (ESR) process. The solutions of the mass, momentum, energy, and species conservation equations were simultaneously calculated by the finite volume method. The Joule heating and Lorentz force were fully coupled through solving the Maxwell’s equations with the assistance of the magnetic potential vector. The movements of the air-slag and slag-metal interfaces were described by the volume of fluid (VOF) approach. In order to include the influences of the air, the slag and the electric current on the desulfurization, a thermodynamic and kinetic module was introduced. An experiment was conducted to validate the model. The completely comparison between the measured and simulated data indicates that the model can describe the desulfurization behavior in the ESR process with an acceptable accuracy. The sulfur in the metal would be transferred into the slag under the combined effect of the slag treatment and the electrochemical reaction, and is primarily achieved in the period of the droplet formation. The sulfur in the slag then could be transferred into the air because of the oxidation. The maximum calculated removal ratio in the whole process is around 88%.

  3. Physics of automated driving in framework of three-phase traffic theory

    Science.gov (United States)

    Kerner, Boris S.

    2018-04-01

    We have revealed physical features of automated driving in the framework of the three-phase traffic theory for which there is no fixed time headway to the preceding vehicle. A comparison with the classical model approach to automated driving for which an automated driving vehicle tries to reach a fixed (desired or "optimal") time headway to the preceding vehicle has been made. It turns out that automated driving in the framework of the three-phase traffic theory can exhibit the following advantages in comparison with the classical model of automated driving: (i) The absence of string instability. (ii) Considerably smaller speed disturbances at road bottlenecks. (iii) Automated driving vehicles based on the three-phase theory can decrease the probability of traffic breakdown at the bottleneck in mixed traffic flow consisting of human driving and automated driving vehicles; on the contrary, even a single automated driving vehicle based on the classical approach can provoke traffic breakdown at the bottleneck in mixed traffic flow.

  4. A Three-Phase Multiobjective Mechanism for Selecting Retail Stores to Close

    Directory of Open Access Journals (Sweden)

    Rong-Chang Chen

    2016-01-01

    Full Text Available To operate a successful and growing business, a retail store manager has to make tough decisions about selectively closing underperforming stores. In this paper, we propose using a three-phase multiobjective mechanism to help retail industry practitioners determine which stores to close. In the first phase, a geographic information system (GIS and k-means clustering algorithm are used to divide all the stores into clusters. In the second phase, stores can be strategically selected according to the requirements of the company and the attributes of the stores. In the third phase, a neighborhood-based multiobjective genetic algorithm (NBMOGA is utilized to determine which stores to close. To examine the effectiveness of the proposed three-phase mechanism, a variety of experiments are performed, based partly on a real dataset from a stock-list company in Taiwan. Results from the experiments show that the proposed three-phase mechanism can help efficiently decide which store locations to close. In addition, the neighborhood radius has a considerable influence on the results.

  5. Comparison of the quench and fault current limiting characteristics of the flux-coupling type SFCL with single and three-phase transformer

    Science.gov (United States)

    Jung, Byung Ik; Cho, Yong Sun; Park, Hyoung Min; Chung, Dong Chul; Choi, Hyo Sang

    2013-01-01

    The South Korean power grid has a network structure for the flexible operation of the system. The continuously increasing power demand necessitated the increase of power facilities, which decreased the impedance in the power system. As a result, the size of the fault current in the event of a system fault increased. As this increased fault current size is threatening the breaking capacity of the circuit breaker, the main protective device, a solution to this problem is needed. The superconducting fault current limiter (SFCL) has been designed to address this problem. SFCL supports the stable operation of the circuit breaker through its excellent fault-current-limiting operation [1-5]. In this paper, the quench and fault current limiting characteristics of the flux-coupling-type SFCL with one three-phase transformer were compared with those of the same SFCL type but with three single-phase transformers. In the case of the three-phase transformers, both the superconducting elements of the fault and sound phases were quenched, whereas in the case of the single-phase transformer, only that of the fault phase was quenched. For the fault current limiting rate, both cases showed similar rates for the single line-to-ground fault, but for the three-wire earth fault, the fault current limiting rate of the single-phase transformer was over 90% whereas that of the three-phase transformer was about 60%. It appears that when the three-phase transformer was used, the limiting rate decreased because the fluxes by the fault current of each phase were linked in one core. When the power loads of the superconducting elements were compared by fault type, the initial (half-cycle) load was great when the single-phase transformer was applied, whereas for the three-phase transformer, its power load was slightly lower at the initial stage but became greater after the half fault cycle.

  6. Chemistry and materials science progress report. Weapons-supporting research and laboratory directed research and development: FY 1995

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-04-01

    This report covers different materials and chemistry research projects carried out a Lawrence Livermore National Laboratory during 1995 in support of nuclear weapons programs and other programs. There are 16 papers supporting weapons research and 12 papers supporting laboratory directed research.

  7. Chemistry and materials science progress report. Weapons-supporting research and laboratory directed research and development: FY 1995

    International Nuclear Information System (INIS)

    1996-04-01

    This report covers different materials and chemistry research projects carried out a Lawrence Livermore National Laboratory during 1995 in support of nuclear weapons programs and other programs. There are 16 papers supporting weapons research and 12 papers supporting laboratory directed research

  8. Water research to support society: past, present and future

    Science.gov (United States)

    Arheimer, Berit

    2014-05-01

    . Historical changes in focus areas clearly reflect the shifts in societal needs, going from industrialization to the information society and globalization. Present research needs will be illustrated in the on-going practical work to support water managers and decision makers with hydrological forecasts, climate change impact assessments, improved water status for biodiversity and statistics for dimensioning safe infrastructure. Different approaches to applied research and ways to implement new knowledge in society will be discussed. Future research is suggested to embrace the complexity of the water systems by linking scales, monitoring systems, processes, disciplines and various users. Some ingredients to achieve a coordinated effort in the scientific community will be suggested, based on new technology, multi-data, transparency and the principles of sharing. To handle the problems of the Antropocene, improved knowledge accumulation to advance science and interactions with other disciplines is absolutely necessary. These should be the basic elements of Panta Rhei.

  9. UAS as a Support for Atmospheric Aerosols Research: Case Study

    Science.gov (United States)

    Chiliński, Michał T.; Markowicz, Krzysztof M.; Kubicki, Marek

    2018-01-01

    Small drones (multi-copters) have the potential to deliver valuable data for atmospheric research. They are especially useful for collecting vertical profiles of optical and microphysical properties of atmospheric aerosols. Miniaturization of sensors, such as aethalometers and particle counters, allows for collecting profiles of black carbon concentration, absorption coefficient, and particle size distribution. Vertical variability of single-scattering properties has a significant impact on radiative transfer and Earth's climate, but the base of global measurements is very limited. This results in high uncertainties of climate/radiation models. Vertical range of modern multi-copters is up to 2000 m, which is usually enough to study aerosols up to the top of planetary boundary layer on middle latitudes. In this study, we present the benefits coming from usage of small drones in atmospheric research. The experiment, described as a case study, was conducted at two stations (Swider and Warsaw) in Poland, from October 2014 to March 2015. For over 6 months, photoacoustic extinctiometers collected data at both stations. This enabled us to compare the stations and to establish ground reference of black carbon concentrations for vertical profiles collected by ceilometer and drone. At Swider station, we used Vaisala CL-31 ceilometer. It delivered vertical profiles of range corrected signal, which were analysed together with profiles acquired by micro-aethalometer AE-51 and Vaisala RS92-SGP radiosonde carried by a hexacopter drone. Near to the surface, black carbon gradient of ≈ 400 (\\upmu g/m^3 )/100 m was detected, which was below the ceilometer minimal altitude of detection. This confirmed the usefulness of drones and potential of their support for remote sensing techniques.

  10. A study on DC hybrid three-phase fault current limiting interrupter for a power distribution system

    International Nuclear Information System (INIS)

    Shao, Hongtian; Satoh, Tomoyuki; Yamaguchi, Mitsugi; Fukui, Satoshi; Ogawa, Jun; Satoh, Takao; Ishikawa, Hiroyuki

    2005-01-01

    For the purpose of protecting electric power system, many researches and developments of fault current limiters are being performed. The authors studied a dc hybrid three-phase fault current limiting interrupter (FCLI) composed of a superconducting reactor and an S/N transition element, connected in series each other. The dc hybrid type fault current limiting interrupter can limit a fault current by means of the inductance of high temperature superconducting (HTS) coil together with the normal transition of HTS bulk material (HTSB). In the case of an accident, the normal transition of the bulk material can be accelerated by the magnetic field of the HTS coil. In this paper, the dc hybrid type fault current limiting interrupter for 5.5 km long 6.6 kV-600 A power distribution system is analyzed, and performances of fault current limitation and interruption are confirmed. Moreover, a reclosing operation is discussed for this power distribution system

  11. Management of Service Projects in Support of Space Flight Research

    Science.gov (United States)

    Love, J.

    2009-01-01

    Goal:To provide human health and performance countermeasures, knowledge, technologies, and tools to enable safe, reliable, and productive human space exploration . [HRP-47051] Specific Objectives: 1) Develop capabilities, necessary countermeasures, and technologies in support of human space exploration, focusing on mitigating the highest risks to human health and performance. 2) Define and improve human spaceflight medical, environmental, and human factors standards. 3) Develop technologies that serve to reduce medical and environmental risks, to reduce human systems resource requirements (mass, volume, power, data, etc.) and to ensure effective human-system integration across exploration systems. 4) Ensure maintenance of Agency core competencies necessary to enable risk reduction in the following areas: A. Space medicine B. Physiological and behavioral effects of long duration spaceflight on the human body C. Space environmental effects, including radiation, on human health and performance D. Space "human factors" [HRP-47051]. Service projects can form integral parts of research-based project-focused programs to provide specialized functions. Traditional/classic project management methodologies and agile approaches are not mutually exclusive paradigms. Agile strategies can be combined with traditional methods and applied in the management of service projects functioning in changing environments. Creative collaborations afford a mechanism for mitigation of constrained resource limitations.

  12. ESTABLISHED MODES AND STATIC CHARACTERISTICS OF THREE-PHASE ASYNCHRONOUS MOTOR POWERED WITH SINGLE PHASE NETWORK

    Directory of Open Access Journals (Sweden)

    V. S. Malyar

    2016-01-01

    Full Text Available A mathematical model is developed to study the operation of three-phase asynchronous motor with squirrel-cage rotor when the stator winding is powered from a single phase network. To create a rotating magnetic field one of the phases is fed through the capacitor. Due to the asymmetry of power feed not only transients, but the steady-state regimes are dynamic, so they are described by differential equations in any coordinate system. Their study cannot be carried out with sufficient adequacy on the basis of known equivalent circuits and require the use of dynamic parameters. In the mathematical model the state equations of the circuits of the stator and rotor are composed in the stationary three phase coordinate system. Calculation of the established mode is performed by solving the boundary problem that makes it possible to obtain the coordinate dependences over the period, without calculation of the transient process. In order to perform it, the original nonlinear differential equations are algebraized by approximating the variables with the use of cubic splines. The resulting nonlinear system of algebraic equations is a discrete analogue of the initial system of differential equations. It is solved by parameter continuation method. To calculate the static characteristics as a function of a certain variable, the system is analytically differentiated, and then numerically integrated over this variable. In the process of integration, Newton's refinement is performed at each step or at every few steps, making it possible to implement the integration in just a few steps using Euler's method. Jacobi matrices in both cases are the same. To account for the current displacement in the rods of the squirrel-cage rotor, each of them, along with the squirrel-cage rings, is divided in height into several elements. This results in several squirrel-cage rotor windings which are represented by three-phase windings with magnetic coupling between them.

  13. Three-phase metal kinetics in terrestrial invertebrates exposed to high metal concentrations

    Energy Technology Data Exchange (ETDEWEB)

    Laskowski, Ryszard, E-mail: ryszard.laskowski@uj.edu.pl [Institute of Environmental Sciences, Jagiellonian University, Gronostajowa 7, 30-387 Krakow (Poland); Bednarska, Agnieszka J. [Institute of Environmental Sciences, Jagiellonian University, Gronostajowa 7, 30-387 Krakow (Poland); Spurgeon, David; Svendsen, Claus [Centre for Ecology and Hydrology, Maclean Building, Benson Lane, Crowmarsh Gifford, Wallingford, Oxon, OX10 8BB (United Kingdom); Gestel, Cornelis A.M. van [Institute of Ecological Science, Vrije Universiteit, De Boelelaan 1085, 1081 HV Amsterdam (Netherlands)

    2010-08-15

    Models of metal toxicokinetics are critically evaluated using both newly generated data in the NoMiracle project as well as those originating from older studies. The analysis showed that the most frequently used one-compartment two-phase toxicokinetic model, with one assimilation and one elimination rate constant, does not describe correctly certain data sets pertaining particularly to the pattern of assimilation of trace elements. Using nickel toxicokinetics in carabid beetles and earthworms as examples, we showed that Ni in fact exhibits a three-phase kinetics with a short phase of fast metal accumulation immediately after exposure, followed by partial elimination to an equilibrium concentration at a later stage of a metal exposure phase, and by final elimination upon transfer to an uncontaminated food/soil. A similar phenomenon was also found for data on cadmium kinetics in ground beetles and copper kinetics in earthworms in data already published in the literature that was not accounted for in the earlier analysis of the data. The three-phase model suggests that the physiology of controlling body metal concentrations can change shortly after exposure, at least in some cases, by increasing the elimination rate and/or decreasing metal assimilation. Hence, the three-phase model, that allows for different assimilation and/or elimination rates in different phases of exposure to a toxicant, may provide insight into temporal changes in the physiology of metal handling. Consequently, this alternative model should always be tested when describing metal toxicokinetics when temporal patterns of internal metal concentration exhibit an initial 'overshoot' in body metal concentrations.

  14. Three-phase metal kinetics in terrestrial invertebrates exposed to high metal concentrations

    International Nuclear Information System (INIS)

    Laskowski, Ryszard; Bednarska, Agnieszka J.; Spurgeon, David; Svendsen, Claus; Gestel, Cornelis A.M. van

    2010-01-01

    Models of metal toxicokinetics are critically evaluated using both newly generated data in the NoMiracle project as well as those originating from older studies. The analysis showed that the most frequently used one-compartment two-phase toxicokinetic model, with one assimilation and one elimination rate constant, does not describe correctly certain data sets pertaining particularly to the pattern of assimilation of trace elements. Using nickel toxicokinetics in carabid beetles and earthworms as examples, we showed that Ni in fact exhibits a three-phase kinetics with a short phase of fast metal accumulation immediately after exposure, followed by partial elimination to an equilibrium concentration at a later stage of a metal exposure phase, and by final elimination upon transfer to an uncontaminated food/soil. A similar phenomenon was also found for data on cadmium kinetics in ground beetles and copper kinetics in earthworms in data already published in the literature that was not accounted for in the earlier analysis of the data. The three-phase model suggests that the physiology of controlling body metal concentrations can change shortly after exposure, at least in some cases, by increasing the elimination rate and/or decreasing metal assimilation. Hence, the three-phase model, that allows for different assimilation and/or elimination rates in different phases of exposure to a toxicant, may provide insight into temporal changes in the physiology of metal handling. Consequently, this alternative model should always be tested when describing metal toxicokinetics when temporal patterns of internal metal concentration exhibit an initial 'overshoot' in body metal concentrations.

  15. Study and Experiment on Non-Contact Voltage Sensor Suitable for Three-Phase Transmission Line.

    Science.gov (United States)

    Zhou, Qiang; He, Wei; Xiao, Dongping; Li, Songnong; Zhou, Kongjun

    2015-12-30

    A voltage transformer, as voltage signal detection equipment, plays an important role in a power system. Presently, more and more electric power systems are adopting potential transformer and capacitance voltage transformers. Transformers are often large in volume and heavyweight, their insulation design is difficult, and an iron core or multi-grade capacitance voltage division structure is generally adopted. As a result, the detection accuracy of transformer is reduced, a huge phase difference exists between detection signal and voltage signal to be measured, and the detection signal cannot accurately and timely reflect the change of conductor voltage signal to be measured. By aiming at the current problems of electric transformation, based on electrostatic induction principle, this paper designed a non-contact voltage sensor and gained detection signal of the sensor through electrostatic coupling for the electric field generated by electric charges of the conductor to be measured. The insulation structure design of the sensor is simple and its volume is small; phase difference of sensor measurement is effectively reduced through optimization design of the electrode; and voltage division ratio and measurement accuracy are increased. The voltage sensor was tested on the experimental platform of simulating three-phase transmission line. According to the result, the designed non-contact voltage sensor can realize accurate and real-time measurement for the conductor voltage. It can be applied to online monitoring for the voltage of three-phase transmission line or three-phase distribution network line, which is in accordance with the development direction of the smart grid.

  16. Three phase dynamic CT with double spiral CT: utility of determination of stomach cancer stage

    International Nuclear Information System (INIS)

    Jung, Min Ha; Kim, Hong In; Kim, Tae Hyung; Lee, Ki Yeol; Cho, June Il; Park, Cheol Min; Cha, In Ho

    1997-01-01

    To evaluate the utility of three phases of spiral CT in the diagnosis of stomach cancer. Between August 1994 and March 1995, thirty eight patients with stomach cancer, demonstrated on spiral CT, underwent surgery. Twenty-eight cases were advanced and ten were early. There were 27 men, and 11 women, and their average age was 52.8 years old (33-77). After ingestion of 600-700ml of water, 120-140ml of nonionic contrast material was injected intravenously. Spiral CT scanning was performed in 10mm slice thickness and of 10mm/sec table speed. Three phase image were obtained at 25sec (arterial phase), 60-65sec (venous phase) and 4min (equilibrium phase) after the start of bolus injection. On each phase, CT findings were compared with pathologic results, and tumor detectibility, depth of tumor invasion and lymph node metastasis was analysed. Thirty of the 38 carcinomas (79%) were detected on the arterial phase, 33 (81%) on the venous phase and 30 (79%) on the equilibrium phase. Depth of tumor invasion was measured accurately in 27 of 38 cases (71%) : T1-4/10 (40%), T2-8/11 (73%), T3-13/15 (87%), T4-2/2 (100%). We overstaged one case of T1 as T2 and two cases of T2 as T3, and understaged one case of T2 as T1 and two cases of T3 as T2. Among the 16 enlarged lymph nodes larger than 8mm, 13 cases were positive on pathologic examination and the sensitivity was 65%. With three-phase spiral CT scanning, we obtained 71% accuracy of depth of tumor invasion. The venous phase is most useful for tumor detection and for determining depth of tumor invasion and lymph node metastasis

  17. A three-phase microfluidic chip for rapid sample clean-up of alkaloids from plant extracts

    NARCIS (Netherlands)

    Tetala, K.K.R.; Swarts, J.W.; Chen, B.; Janssen, A.E.M.; Beek, van T.A.

    2009-01-01

    A three-phase microchip was developed for the rapid and efficient small-scale purification of alkaloids from plant extracts. As part of the development of such a three-phase microchip, first a two-phase microchip with two channels (3.2 cm and 9.3 cm) was used to study the extraction efficiency of

  18. Dead Zone Oscillator Control for Communication-Free Synchronization of Paralleled, Three-Phase, Current-Controlled Inverters

    Science.gov (United States)

    2016-05-11

    Current-Controlled Inverters by Midshipman 1/C Spencer C. Shabshab, USN UNITED STATES NAVAL ACADEMY...Three-Phase, Current-Controlled Inverters by Midshipman 1/C Spencer C. Shabshab United States Naval Academy Annapolis, Maryland...for Communication-Free Synchronization of Paralleled, 5a. CONTRACT NUMBER Three-Phase, Current-Controlled Inverters 5b. GRANT NUMBER 5c

  19. Optimized Carrier Based Multilevel Generated Modified Dual Three-Phase Open-Winding Inverter for Medium Power Applications

    DEFF Research Database (Denmark)

    Padmanaban, Sanjeevi Kumar; Blaabjerg, Frede; Wheeler, Patrick

    2016-01-01

    This paper presents a novel carrier based multilevel modulation for modified dual three-phase open-winding inverter applicable for low-voltage/high-current applications. A standard three-phase voltage source inverter (VSI) is connected across the open-winding of both ends of the motor. Each VSI i...

  20. Skull base osteomyelitis: role of three phase and hybrid SPECT/CT bone scintigraphy

    International Nuclear Information System (INIS)

    Chakraborty, D.; Bhattacharaya, A.; Kamaleshwaran, K.K.; Mittal, B.R.; Aggarwal, K.; Singh, B.; Bhoil, A.

    2010-01-01

    Full text: Skull base osteomyelitis is the infection that has spread to the skull base, beyond the external auditory canal and seen in advanced stage of malignant otitis externa. Early diagnosis of this condition includes the use of bone scintigraphy since clinical assessment alone cannot differentiate the skull base osteomyelitis from the severe type of otitis externa in which there is no extension to the adjacent bone. Objective: To determine the role of three phase bone scintigraphy and delayed SPECT/CT in detection of skull base osteomyelitis in patients with malignant otitis externa. Material and Methods: Clinical records of 20 patients (14 Males and 6 Females; mean age 72 yrs) of otitis externa with suspected skull base involvement referred for bone scintigraphies were analyzed retrospectively. Three phase bone scintigraphy was acquired under dual detector gamma camera after intravenous injection of 20 mCi (740 MBq) 99m Tc-MDP followed by SPECT/CT of the skull. Scintigraphic findings were compared with clinical symptoms, signs and diagnostic CT scan findings. Results: All the patients except one were diabetic and having elevated ESR. 18 patients presented with bilateral symptoms and rest unilateral. Cranial nerves were involved in 8 patients (40%). Ear discharge culture sensitivity report was found in three patients; it was positive for Pseudomonas aeruginosa for two patients and in Diptheroids for one. In 9 patients (45%) increased flow of tracer and 10 patients (50%) increased blood pool phase in the temporal region was found. Delayed phase images showed increased uptake in skull bone in 19 patients (95%). Hybrid SPECT/CT of the skull localized areas of increased tracer uptake to the mastoid part in 15 patients (75%), petrous part in 11 patients (55%), sphenoid in 3 patients (15%) and zygomatic bone in one patient (5%) with CT showing destructive changes in 5 patients (25%) which were corroborated with diagnostic CT findings. SPECT/CT along with three phase

  1. Vector control of three-phase AC machines system development in the practice

    CERN Document Server

    Quang, Nguyen Phung; Dittrich, J

    2015-01-01

    This book addresses the vector control of three-phase AC machines, in particular induction motors with squirrel-cage rotors (IM), permanent magnet synchronous motors (PMSM) and doubly-fed induction machines (DFIM), from a practical design and development perspective. The main focus is on the application of IM and PMSM in electrical drive systems, where field-orientated control has been successfully established in practice. It also discusses the use of grid-voltage oriented control of DFIMs in wind power plants. This second, enlarged edition includes new insights into flatness-based  nonlinear

  2. Wavelet-Fuzzy Speed Indirect Field Oriented Controller for Three-Phase AC Motor Drive

    DEFF Research Database (Denmark)

    Sanjeevikumar, Padmanaban; Daya, Febin; Blaabjerg, Frede

    2016-01-01

    Three-phase voltage source inverter driven induction motor are used in many medium- and high-power applications. Precision in speed of the motor play vital role, i.e. popular methods of direct/indirect field-oriented control (FOC) are applied. FOC is employed with proportional-integral (P...... wavelet transform and the fuzzy logic controller, to generate the scaled gains for the indirect FOC induction motor. Complete model of the proposed ac motor drive is developed with numerical simulation Matlab/Simulink software and tested under different working conditions. For experimental verification...

  3. Performance characteristic of saturable three-phase interface transformers-investigations using a model simulation

    Energy Technology Data Exchange (ETDEWEB)

    Gierse, G; Pestka, J

    1981-11-01

    For electric locomotive drives equipped with converter fed squirrel cage induction motors the influence of different three-phase interface transformers on the smoothing of the motor currents is shown. In combination with a modified pulse-width-controlled thyristor firing system the size of the interface transformers can be greatly reduced without the distortion currents being greater than in the case of reactors in the motor supply lines. Finally, it is shown how the additional magnetic coupling of two driving systems can influence the behaviour of the two motors.

  4. Sharing of nonlinear load in parallel-connected three-phase converters

    DEFF Research Database (Denmark)

    Borup, Uffe; Blaabjerg, Frede; Enjeti, Prasad N.

    2001-01-01

    compensation are connected in parallel. Without the new solution, they are normally not able to distinguish the harmonic currents that flow to the load and harmonic currents that circulate between the converters. Analysis and experimental results on two 90-kVA 400-Hz converters in parallel are presented......In this paper, a new control method is presented which enables equal sharing of linear and nonlinear loads in three-phase power converters connected in parallel, without communication between the converters. The paper focuses on solving the problem that arises when two converters with harmonic....... The results show that both linear and nonlinear loads can be shared equally by the proposed concept....

  5. A parametric study on unbalanced three phase islanded microgrids with inverter interfaced units

    DEFF Research Database (Denmark)

    Sanseverino, Eleonora Riva; Quang, Ninh Nguyen; Zizzo, Gaetano

    2013-01-01

    In this paper, the solution of the power flow for unbalanced three phase microgrids systems is proposed. The study aims at the integration of inverter interfaced units using the control law used for primary voltage and frequency regulation, so as to take into account possible small variations...... of these parameters to account for sudden load changes. The proposed study deals with unbalanced systems which is the typical case of small distribution systems and shows how the power losses term varies as the regulators parameters vary as well, thus showing that these are sensitive parameters that could have...

  6. Distributed Strategy for Optimal Dispatch of Unbalanced Three-Phase Islanded Microgrids

    DEFF Research Database (Denmark)

    Vergara Barrios, Pedro Pablo; Rey-López, Juan Manuel; Shaker, Hamid Reza

    2018-01-01

    This paper presents a distributed strategy for the optimal dispatch of islanded microgrids, modeled as unbalanced three-phase electrical distribution systems (EDS). To set the dispatch of the distributed generation (DG) units, an optimal generation problem is stated and solved distributively based......-phase microgrid. According to the obtained results, the proposed strategy achieves a lower cost solution when compared with a centralized approach based on a static droop framework, with a considerable reduction on the communication system complexity. Additionally, it corrects the mismatch between generation...

  7. Secondary Voltage Unbalance Compensation for Three-Phase Four-Wire Islanded Microgrids

    DEFF Research Database (Denmark)

    Tang, Fen; Zhou, Xiao; Meng, Lexuan

    2014-01-01

    This paper proposes a secondary voltage unbalance control approach that compensate voltage unbalances in three-phase four-wire islanded microgrid systems. It is implemented in the secondary control level of the microgrid hierarchical control structure. By sending information through low......-bandwidth communication links to the primary control level, the required unbalanced factors at sensitive buses are achieved. Also, negative and zero sequence equivalent circuits and unbalance compensation principle are derived. Finally, real-time hardware-in-the-loop results show the feasibility of the proposed approach...

  8. Power loss benchmark of nine-switch converters in three-phase online-UPS application

    DEFF Research Database (Denmark)

    Qin, Zian; Loh, Poh Chiang; Blaabjerg, Frede

    2014-01-01

    Three-phase online-UPS is an appropriate application for the nine-switch converter, where its high voltage stress of the power device caused by the reduced switch feature can be relieved significantly. Its power loss and loss distribution still have the flexibility from the control point of view...... as parameters like modulation index and phase angle of the load are taken into account. The benchmark of power loss will become a guidance for the users to make best use of the advantages and bypass the disadvantages of nine-switch converters. The results are finally verified on a 1.5 kW prototype....

  9. 75 FR 57520 - NASA Advisory Council; Planetary Science Subcommittee; Supporting Research and Technology Working...

    Science.gov (United States)

    2010-09-21

    ... NATIONAL AERONAUTICS AND SPACE ADMINISTRATION [Notice (10-112)] NASA Advisory Council; Planetary Science Subcommittee; Supporting Research and Technology Working Group; Meeting AGENCY: National... announces a meeting of the Supporting Research and Technology Working Group of the Planetary Science...

  10. Economic Research Forum - Core Support 2012-2014 | IDRC ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    The Economic Research Forum (ERF) is a Cairo-based regional economics ... resource for researchers, publishing The Middle East Development Journal, and ... long-term climate action to reduce social inequality, promote greater gender ...

  11. TTI Phase 2 Institutional Support: Centre for Policy Research | IDRC ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    ... help enhance its research quality, organizational performance, and policy engagement. ... IDRC invests in research and knowledge to empower women in India ... women, prevent gender-based violence, and make digital platforms work for ...

  12. New partnership to support Ebola research teams | IDRC ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    2018-05-29

    May 29, 2018 ... ... the Social Sciences and Humanities Research Council (SSHRC), and ... and/or social science research in the context of this particular health emergency. ... A new website and resource library will help improve developing ...

  13. Homogenization of linear viscoelastic three phase media: internal variable formulation versus full-field computation

    International Nuclear Information System (INIS)

    Blanc, V.; Barbie, L.; Masson, R.

    2011-01-01

    Homogenization of linear viscoelastic heterogeneous media is here extended from two phase inclusion-matrix media to three phase inclusion-matrix media. Each phase obeying to a compressible Maxwellian behaviour, this analytic method leads to an equivalent elastic homogenization problem in the Laplace-Carson space. For some particular microstructures, such as the Hashin composite sphere assemblage, an exact solution is obtained. The inversion of the Laplace-Carson transforms of the overall stress-strain behaviour gives in such cases an internal variable formulation. As expected, the number of these internal variables and their evolution laws are modified to take into account the third phase. Moreover, evolution laws of averaged stresses and strains per phase can still be derived for three phase media. Results of this model are compared to full fields computations of representative volume elements using finite element method, for various concentrations and sizes of inclusion. Relaxation and creep test cases are performed in order to compare predictions of the effective response. The internal variable formulation is shown to yield accurate prediction in both cases. (authors)

  14. Three-Phase AC Optimal Power Flow Based Distribution Locational Marginal Price: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Rui; Zhang, Yingchen

    2017-05-17

    Designing market mechanisms for electricity distribution systems has been a hot topic due to the increased presence of smart loads and distributed energy resources (DERs) in distribution systems. The distribution locational marginal pricing (DLMP) methodology is one of the real-time pricing methods to enable such market mechanisms and provide economic incentives to active market participants. Determining the DLMP is challenging due to high power losses, the voltage volatility, and the phase imbalance in distribution systems. Existing DC Optimal Power Flow (OPF) approaches are unable to model power losses and the reactive power, while single-phase AC OPF methods cannot capture the phase imbalance. To address these challenges, in this paper, a three-phase AC OPF based approach is developed to define and calculate DLMP accurately. The DLMP is modeled as the marginal cost to serve an incremental unit of demand at a specific phase at a certain bus, and is calculated using the Lagrange multipliers in the three-phase AC OPF formulation. Extensive case studies have been conducted to understand the impact of system losses and the phase imbalance on DLMPs as well as the potential benefits of flexible resources.

  15. Improved modeling of new three-phase high voltage transformer with magnetic shunts

    Directory of Open Access Journals (Sweden)

    Chraygane M.

    2015-03-01

    Full Text Available This original paper deals with a new approach for the study of behavior in nonlinear regime of a new three-phase high voltage power supply for magnetrons, used for the microwave generators in industrial applications. The design of this system is composed of a new three-phase leakage flux transformer supplying by phase a cell, composed of a capacitor and a diode, which multiplies the voltage and stabilizes the current. Each cell. in turn, supplies a single magnetron. An equivalent model of this transformer is developed taking into account the saturation phenomenon and the stabilization process of each magnetron. Each inductance of the model is characterized by a non linear relation between flux and current. This model was tested by EMTP software near the nominal state. The theoretical results were compared to experimental measurements with a good agreement. Relative to the current device, the new systemprovides gains of size, volume, cost of implementation and maintenance which make it more economical.

  16. Modeling and reliability analysis of three phase z-source AC-AC converter

    Directory of Open Access Journals (Sweden)

    Prasad Hanuman

    2017-12-01

    Full Text Available This paper presents the small signal modeling using the state space averaging technique and reliability analysis of a three-phase z-source ac-ac converter. By controlling the shoot-through duty ratio, it can operate in buck-boost mode and maintain desired output voltage during voltage sag and surge condition. It has faster dynamic response and higher efficiency as compared to the traditional voltage regulator. Small signal analysis derives different control transfer functions and this leads to design a suitable controller for a closed loop system during supply voltage variation. The closed loop system of the converter with a PID controller eliminates the transients in output voltage and provides steady state regulated output. The proposed model designed in the RT-LAB and executed in a field programming gate array (FPGA-based real-time digital simulator at a fixedtime step of 10 μs and a constant switching frequency of 10 kHz. The simulator was developed using very high speed integrated circuit hardware description language (VHDL, making it versatile and moveable. Hardware-in-the-loop (HIL simulation results are presented to justify the MATLAB simulation results during supply voltage variation of the three phase z-source ac-ac converter. The reliability analysis has been applied to the converter to find out the failure rate of its different components.

  17. Multilevel Converter by Cascading Two-Level Three-Phase Voltage Source Converter

    Directory of Open Access Journals (Sweden)

    Abdullrahman A. Al-Shamma’a

    2018-04-01

    Full Text Available This paper proposes a topology using isolated, cascaded multilevel voltage source converters (VSCs and employing two-winding magnetic elements for high-power applications. The proposed topology synthesizes 6 two-level, three-phase VSCs, so the power capability of the presented converter is six times the capability of each VSC module. The characteristics of the proposed topology are demonstrated through analyzing its current relationships, voltage relationships and power capability in detail. The power rating is equally shared among the VSC modules without the need for a sharing algorithm; thus, the converter operates as a single three-phase VSC. The comparative analysis with classical neutral-point clamped, flying capacitor and cascaded H-bridge exhibits the superior features of fewer insulated gate bipolar transistors (IGBTs, capacitor requirement and fewer diodes. To validate the theoretical performance of the proposed converter, it is simulated in a MATLAB/Simulink environment and the results are experimentally demonstrated using a laboratory prototype.

  18. An analytical inductor design procedure for three-phase PWM converters in power factor correction applications

    DEFF Research Database (Denmark)

    Kouchaki, Alireza; Niroumand, Farideh Javidi; Haase, Frerk

    2015-01-01

    This paper presents an analytical method for designing the inductor of three-phase power factor correction converters (PFCs). The complex behavior of the inductor current complicates the inductor design procedure as well as the core loss and copper loss calculations. Therefore, this paper analyze...... to calculate the core loss in the PFC application. To investigate the impact of the dc link voltage level, two inductors for different dc voltage levels are designed and the results are compared.......This paper presents an analytical method for designing the inductor of three-phase power factor correction converters (PFCs). The complex behavior of the inductor current complicates the inductor design procedure as well as the core loss and copper loss calculations. Therefore, this paper analyzes...... circuit is used to provide the inductor current harmonic spectrum. Therefore, using the harmonic spectrum, the low and high frequency copper losses are calculated. The high frequency minor B-H loops in one switching cycle are also analyzed. Then, the loss map provided by the measurement setup is used...

  19. Heat transfer modelling of two-phase bubbles swarm condensing in three - phase direct - contact condenser

    Directory of Open Access Journals (Sweden)

    Mahood Hameed B.

    2016-01-01

    Full Text Available An analytical model for the convective heat transfer coefficient and the two-phase bubble size of a three-phase direct contact heat exchanger was developed. Until the present, there has only been a theoretical model available that deals with a single two-phase bubble and a bubble train condensation in an immiscible liquid. However, to understand the actual heat transfer process within the three-phase direct contact condenser, characteristic models are required. A quasi - steady energy equation in a spherical coordinate system with a potential flow assumption and a cell model configuration has been simplified and solved analytically. The convective heat transfer in terms of Nu number has been derived, and it was found to be a function to Pe number and a system void fraction. In addition, the two-phase bubble size relates to the system void fraction and has been developed by solving a simple energy balance equation and using the derived convective heat transfer coefficient expression. Furthermore, the model correlates well with previous experimental data and theoretical results.

  20. Positioning graphical objects on computer screens: a three-phase model.

    Science.gov (United States)

    Pastel, Robert

    2011-02-01

    This experiment identifies and models phases during the positioning of graphical objects (called cursors in this article) on computer displays. The human computer-interaction community has traditionally used Fitts' law to model selection in graphical user interfaces, whereas human factors experiments have found the single-component Fitts' law inadequate to model positioning of real objects. Participants (N=145) repeatedly positioned variably sized square cursors within variably sized rectangular targets using computer mice. The times for the cursor to just touch the target, for the cursor to enter the target, and for participants to indicate positioning completion were observed. The positioning tolerances were varied from very precise and difficult to imprecise and easy. The time for the cursor to touch the target was proportional to the initial cursor-target distance. The time for the cursor to completely enter the target after touching was proportional to the logarithms of cursor size divided by target tolerances. The time for participants to indicate positioning after entering was inversely proportional to the tolerance. A three-phase model defined by regions--distant, proximate, and inside the target--was proposed and could model the positioning tasks. The three-phase model provides a framework for ergonomists to evaluate new positioning techniques and can explain their deficiencies. The model provides a means to analyze tasks and enhance interaction during positioning.

  1. Three-Phase Time-Multiplexed Planar Power Transmission to Distributed Implants.

    Science.gov (United States)

    Lee, Byunghun; Ahn, Dukju; Ghovanloo, Maysam

    2016-03-01

    A platform has been presented for wireless powering of receivers (Rx's) that are arbitrarily distributed over a large area. A potential application could be powering of small Rx implants, distributed over large areas of the brain. The transmitter (Tx) consists of three overlapping layers of hexagonal planar spiral coils (hex-PSC) that are horizontally shifted to provide the strongest and most homogeneous electromagnetic flux coverage. The three-layer hex-PSC array is driven by a three-phase time-division-multiplexed power Tx that takes the advantage of the carrier phase shift, coil geometries, and Rx time constant to homogeneously power the arbitrarily distributed Rx's regardless of their misalignments. The functionality of the proposed three-phase power transmission concept has been verified in a detailed scaled-up high-frequency structure simulator Advanced Design System simulation model and measurement setup, and compared with a conventional Tx. The new Tx delivers 5.4 mW to each Rx and achieves, on average, 5.8% power transfer efficiency to the Rx at the worst case 90° angular misalignment, compared with 1.4% by the conventional Tx.

  2. Noise and Vibration Monitoring for Premium Efficiency IE 3 Three-Phase Induction Motors

    Directory of Open Access Journals (Sweden)

    NISTOR, C. G.

    2015-08-01

    Full Text Available The paper presents the original SV-100 platform that enables low-cost and very high accuracy determinations of noise and vibration levels. The aim of the proposed platform is to achieve an effective integration of the two topics of this analysis: vibrations and noises. To the best of our knowledge, no low price, dedicated compact platform with embedded measuring instruments exists. For proving the practical utility of the proposed platform, two induction motors of 7.5 kW and 11 kW, respectively, in single-layer winding, at 1000 rpm, with IE3 premium efficiency were analyzed. This analysis is required because, according to IEC60034-30 standard, the IE3 efficiency standard has become mandatory for induction motors of rated power greater than 7.5 kW. Therefore, in order to improve the motor operating efficiency, the power losses caused by noises and vibrations have to be reduced. Several variants of supply were studied, i.e., by the three-phase 50 Hz network and by a three-phase inverter at 40, 50 and 60 Hz, respectively. The experimental determinations of noises are presented comparatively, by using a Bruel&Kjaer sonometer and by using the new platform SV-100. The results are compared with the IEC60034 standard.

  3. Simulation of three-phase induction motor drives using indirect field oriented control in PSIM environment

    Science.gov (United States)

    Aziri, Hasif; Patakor, Fizatul Aini; Sulaiman, Marizan; Salleh, Zulhisyam

    2017-09-01

    This paper presents the simulation of three-phase induction motor drives using Indirect Field Oriented Control (IFOC) in PSIM environment. The asynchronous machine is well known about natural limitations fact of highly nonlinearity and complexity of motor model. In order to resolve these problems, the IFOC is applied to control the instantaneous electrical quantities such as torque and flux component. As FOC is controlling the stator current that represented by a vector, the torque component is aligned with d coordinate while the flux component is aligned with q coordinate. There are five levels of the incremental system are gradually built up to verify and testing the software module in the system. Indeed, all of system build levels are verified and successfully tested in PSIM environment. Moreover, the corresponding system of five build levels are simulated in PSIM environment which is user-friendly for simulation studies in order to explore the performance of speed responses based on IFOC algorithm for three-phase induction motor drives.

  4. Completion of a high efficiency ultralarge capacity three-phase transformer

    International Nuclear Information System (INIS)

    Maejima, Masaaki; Maruyama, Katsuya; Fukuda, Teruo.

    1986-01-01

    As for the boosting transformers for thermal and nuclear power stations, at present the ultralarge capacity transformers of 1000 - 1200 MVA class are the main, and particularly in nuclear power, accompanying the development of improved type BWRs and the rise of system stability, there is the tendency toward further large capacity and large size. Consequently, reflecting the recent rise of energy cost, the demand of energy conservation and the reduction of required sites heightened largely as well as the high reliability. In order to meet these demands, Hitachi Ltd. has established the technology of changing to iron machines such as ultralarge iron cores and ultralarge capacity undivided disk windings using the latest design and manufacture techniques were applied to the 525 kV, 1200 MVA transformer for No.4 plant in Fukushima No.2 Nuclear Power Station, Tokyo Electric Power Co., Inc., thus a three-phase transformer of the highest level, high efficiency and ultralarge capacity was completed. In this paper, the outline of this transformer and the test for verifying its reliability are described. The technical change of large capacity three-phase transformers, the specifications, construction, manufacture, reliability test and the effect of modification of this transformer, and the expansion of application to the next generation ultralarge capacity transformers are reported. (Kako, I.)

  5. Alcohol vapour detection at the three phase interface using enzyme-conducting polymer composites.

    Science.gov (United States)

    Winther-Jensen, Orawan; Kerr, Robert; Winther-Jensen, Bjorn

    2014-02-15

    Immobilisation of enzymes on a breathable electrode can be useful for various applications where the three-phase interface between gas or chemical vapour, electrolyte and electrode is crucial for the reaction. In this paper, we report the further development of the breathable electrode concept by immobilisation of alcohol dehydrogenase into vapour-phase polymerised poly(3,4-ethylene dioxythiophene) that has been coated onto a breathable membrane. Typical alcohol sensing, whereby the coenzyme β-Nicotinamide adenine dinucleotide (NADH) is employed as a redox-mediator, was successfully used as a model reaction for the oxidation of ethanol. This indicates that the ethanol vapour from the backside of the membrane has access to the active enzyme embedded in the electrode. The detecting range of the sensor is suitable for the detection of ethanol in fruit juices and for the baseline breath ethanol concentration of drunken driving. After continuous operation for 4.5h the system only showed a 20% decrease in the current output. The electrodes maintained 62% in current output after being refrigerated for 76 days. This work is continuing the progress of the immobilisation of specific enzymes for certain electrochemical reactions whereby the three-phase interface has to be maintained and/or the simultaneous separation of gas from liquid is required. © 2013 Elsevier B.V. All rights reserved.

  6. Direct transformation of solar energy into three-phase current for technical uses

    Energy Technology Data Exchange (ETDEWEB)

    von Hacht, G [Ingenieurbuero Opto-Sensor-Technik, Frankfurt am Main (Germany, F.R.)

    1977-08-01

    The author proposes a method which may increase the 15% efficiency of present solar plants. In principle, the device consists of an optical waveguide tube containing a chain of solar elements. The tube serves as conductive wire for the primary coil of an a.c. or three-phase current transformer. The 50 Hz cycle of the a.c. or three-phase current is generated by rotor or cylindrical diaphragms and/or electronic pilot/thyristor control. The solar energy is focussed axially and/or vertically to the axis of the optical waveguide tube. The light going through the optical waveguide tube makes it possible for solar elements to be equipped with light-sensitive layers on both sides instead of just on one side, as until now. This means a higher efficiency than for conventional solar elements exposed to light only on one side. In addition, the optical waveguide tube is designed in its length as Fabry-Perot resonator. This way, it may also be used as a gas laser. The light generated in this gas laser would multiply the luminous intensity which again acts on the two light-sensitive sides of the solar elements, thus again increasing their efficiency.

  7. MECHANICAL CHARACTERISTICS OF THREE-PHASE INDUCTION MOTORS WITH SINGLE-PHASE POWER SUPPLY

    Directory of Open Access Journals (Sweden)

    V.S. Malyar

    2016-06-01

    Full Text Available Aim. Development of a method for calculating mechanical characteristics of three-phase induction motors with single-phase power supply. Methods. The developed algorithm is based on the high-adequacy mathematical model of motor and projection method for solving the boundary problem for equations of electrical circuits balance presented in the three-phase coordinate system. As a result of asymmetry of power supply to the stator windings, in steady state, flux-linkage and current change according to the periodic law. They are determined by solving the boundary problem. Results. The developed mathematical model allows determining periodic dependence of coordinates as a function of slip and, based on them, mechanical characteristics of motors. Academic novelty. The developed method relies on a completely new mathematical approach to calculation of stationary modes of nonlinear electromagnetic circuits, which allows obtaining periodic solution in a timeless domain. Practical value. Using the developed calculation algorithm, one can select capacitance required to start an induction motor with single-phase power supply and calculate static mechanical characteristics at a given capacitance.

  8. TTI Phase 2 Institutional Support: Centre for Policy Research | CRDI ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    CPR is an independent, non-partisan research institute focused on improving policy-making and management, and promoting national development in India. CPR's research covers ... For CPR, this project will help enhance its research quality, organizational performance, and policy engagement. Policy influence in India

  9. A Framework to Support Research on Informal Inferential Reasoning

    Science.gov (United States)

    Zieffler, Andrew; Garfield, Joan; delMas, Robert; Reading, Chris

    2008-01-01

    Informal inferential reasoning is a relatively recent concept in the research literature. Several research studies have defined this type of cognitive process in slightly different ways. In this paper, a working definition of informal inferential reasoning based on an analysis of the key aspects of statistical inference, and on research from…

  10. Institutional Support to South Asian Policy Research Organizations ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    There are very few policy research organizations in South Asia outside India. Those that exist are fragile due to little demand for policy research, limited if no funding from local sources, and an often insecure political climate. This grant will strengthen the ability of the seven selected research institutions in Bangladesh, Nepal ...

  11. Institutional Support to Latin American Policy Research Organizations

    International Development Research Centre (IDRC) Digital Library (Canada)

    This grant will strengthen the ability of the 12 selected research institutions to provide, disseminate and communicate high-quality research. This will be achieved through measures aimed at enhancing the ability of staff to conduct sound research, improving organizational governance, and communicating with policymakers.

  12. THE MEASUREMENT OF SOCIAL SUPPORT IN THE EUROPEAN RESEARCH ON INCAPACITATING DISEASES AND SOCIAL SUPPORT - THE DEVELOPMENT OF THE SOCIAL SUPPORT QUESTIONNAIRE FOR TRANSACTIONS (SSQT)

    NARCIS (Netherlands)

    SUURMEIJER, TPBM; DOEGLAS, DM; BRIANCON, S; KRIJNEN, WP; KROL, B; SANDERMAN, R; MOUM, T; BJELLE, A; VANDENHEUVEL, WJA

    Social support is supposed to have a beneficial effect on the health and wellbeing of people. It is a central concept in the 'EUropean Research on Incapacitating DIseaes and Social Support' (EURIDISS). In general, two main distinctions concerning social support are made in the literature, providing

  13. The measurement of social support in the European Research on incapaciting diseases and social support : the development of the social support questionnaire for transactions (SSQT)

    NARCIS (Netherlands)

    Suurmeijer, T P B M; Doeglas, D M; Briançon, S; Krijnen, W; Krol, B.; Sanderman, R.; Moum, T; Bjelle, A; van den Heuvel, W.J.A.

    1995-01-01

    Social support is supposed to have a beneficial effect on the health and wellbeing of people. It is a central concept in the "European Research on Incapacitating Diseases and Social Support" (EURIDISS). In general, two main distinctions concerning social support are made in the literature, providing

  14. Establishing a distributed national research infrastructure providing bioinformatics support to life science researchers in Australia.

    Science.gov (United States)

    Schneider, Maria Victoria; Griffin, Philippa C; Tyagi, Sonika; Flannery, Madison; Dayalan, Saravanan; Gladman, Simon; Watson-Haigh, Nathan; Bayer, Philipp E; Charleston, Michael; Cooke, Ira; Cook, Rob; Edwards, Richard J; Edwards, David; Gorse, Dominique; McConville, Malcolm; Powell, David; Wilkins, Marc R; Lonie, Andrew

    2017-06-30

    EMBL Australia Bioinformatics Resource (EMBL-ABR) is a developing national research infrastructure, providing bioinformatics resources and support to life science and biomedical researchers in Australia. EMBL-ABR comprises 10 geographically distributed national nodes with one coordinating hub, with current funding provided through Bioplatforms Australia and the University of Melbourne for its initial 2-year development phase. The EMBL-ABR mission is to: (1) increase Australia's capacity in bioinformatics and data sciences; (2) contribute to the development of training in bioinformatics skills; (3) showcase Australian data sets at an international level and (4) enable engagement in international programs. The activities of EMBL-ABR are focussed in six key areas, aligning with comparable international initiatives such as ELIXIR, CyVerse and NIH Commons. These key areas-Tools, Data, Standards, Platforms, Compute and Training-are described in this article. © The Author 2017. Published by Oxford University Press.

  15. New research centre supports adaptation efforts in Egypt's Nile Delta

    International Development Research Centre (IDRC) Digital Library (Canada)

    2014-06-20

    Jun 20, 2014 ... ... one of the world's most vulnerable regions to climate change threats. ... This effect was recently explored in another IDRC-supported project, which ... in Kenya, farmers seldom use them for farm level decision-making.

  16. Electrical engineering research support for FDOT Traffic Statistics Office

    Science.gov (United States)

    2010-03-01

    The aim of this project was to provide electrical engineering support for the telemetered traffic monitoring sites (TTMSs) operated by the Statistics Office of the Florida Department of Transportation. This project was a continuation of project BD-54...

  17. Implications of Decision Making Research for Decision Support and Displays

    OpenAIRE

    Morrison, Jeffrey G.; Kelly, Richard T.; Moore, Ronald A.; Hutchins, Susan G.

    1998-01-01

    To appear in J. A. Cannon-Bowers & E. Salas (Eds.), Decision Making Under Stress: Implications for Training and Simulation. A prototype decision support system (DSS) was developed to enhance Navy tactical decision making based on naturalistic decision processes. Displays were developed to support critical decision making tasks through recognition-primed and explanation-based reasoning processes, and cognitive analysis was conducted of the decision making problems faced by Navy ...

  18. Research on the Relationship Between Conflict Management and Organizational Support

    OpenAIRE

    Fuat Oktay

    2016-01-01

    The purpose of the present study is to determine the relationship between Turkish Technic Inc. employees’ conflict management styles and perceived organizational support. The sample of the study which was conducted with correlational and descriptive survey models consisted of 1443 Turkish Airlines employees. A 28-item Conflict Management Style Scale, which was developed by Aflazur (1992) and adapted to Turkish by Boz (2012) and an 8-item Perceived Organizational Support S...

  19. Fault Diagnosis of Three Phase Induction Motor Using Current Signal, MSAF-Ratio15 and Selected Classifiers

    Directory of Open Access Journals (Sweden)

    Glowacz A.

    2017-12-01

    Full Text Available A degradation of metallurgical equipment is normal process depended on time. Some factors such as: operation process, friction, high temperature can accelerate the degradation process of metallurgical equipment. In this paper the authors analyzed three phase induction motors. These motors are common used in the metallurgy industry, for example in conveyor belt. The diagnostics of such motors is essential. An early detection of faults prevents financial loss and downtimes. The authors proposed a technique of fault diagnosis based on recognition of currents. The authors analyzed 4 states of three phase induction motor: healthy three phase induction motor, three phase induction motor with 1 faulty rotor bar, three phase induction motor with 2 faulty rotor bars, three phase induction motor with faulty ring of squirrel-cage. An analysis was carried out for original method of feature extraction called MSAF-RATIO15 (Method of Selection of Amplitudes of Frequencies – Ratio 15% of maximum of amplitude. A classification of feature vectors was performed by Bayes classifier, Linear Discriminant Analysis (LDA and Nearest Neighbour classifier. The proposed technique of fault diagnosis can be used for protection of three phase induction motors and other rotating electrical machines. In the near future the authors will analyze other motors and faults. There is also idea to use thermal, acoustic, electrical, vibration signal together.

  20. SARC: Development and Support of a Sarcoma Research Consortium Infrastructure

    Energy Technology Data Exchange (ETDEWEB)

    Arkison, Jim

    2007-10-29

    SARC is a non-for-profit organization whose mission and vision is to advocate for the collaboration on the design of clinical trials on sarcoma, to further the knowledge regarding the diagnosis and treatment of sarcoma and provide accurate and up to date information to physicians, patients and families. The objectives are to assist in the development of the infrastructure for the continued growth and spectrum of clinical research, to facilitate biannual meeting of investigators, and to develop a preclinical research base that would design and conduct research that would improve the process of drug treatments selected for clinical research trials.

  1. Increasing European Support for Neglected Infectious Disease Research

    Directory of Open Access Journals (Sweden)

    Ole F. Olesen

    Full Text Available Neglected infectious diseases (NIDs are a persistent cause of death and disability in low-income countries. Currently available drugs and vaccines are often ineffective, costly or associated with severe side-effects. Although the scale of research on NIDs does not reflect their disease burden, there are encouraging signs that NIDs have begun to attract more political and public attention, which have translated into greater awareness and increased investments in NID research by both public and private donors. Using publicly available data, we analysed funding for NID research in the European Union's (EU's 7th Framework Programme for Research and Technological Development (FP7, which ran from 2007 to 2013. During FP7, the EU provided €169 million for 65 NID research projects, and thereby placed itself among the top global funders of NID research. Average annual FP7 investment in NID research exceeded €24 million, triple that committed by the EU before the launch of FP7. FP7 NID projects involved research teams from 331 different institutions in 72 countries on six continents, underlining the increasingly global nature of European research activities. NID research has remained a priority in the current EU Framework Programme for research and innovation, Horizon 2020, launched in 2014. This has most notably been reflected in the second programme of the European & Developing Countries Clinical Trials Partnership (EDCTP, which provides unprecedented opportunities to advance the clinical development of new medical interventions against NIDs. Europe is thus better positioned than ever before to play a major role in the global fight against NIDs.

  2. How Might Better Network Theories Support School Leadership Research?

    Science.gov (United States)

    Hadfield, Mark; Jopling, Michael

    2012-01-01

    This article explores how recent research in education has applied different aspects of "network" theory to the study of school leadership. Constructs from different network theories are often used because of their perceived potential to clarify two perennial issues in leadership research. The first is the relative importance of formal and…

  3. Institutional Support : Kenya Institute for Public Policy Research and ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    In 2006 the Government of Kenya passed an Act of Parliament making the Kenya Institute for Public Policy Research and Analysis (KIPPRA) the government's lead socioeconomic research institute. The Act exerts enormous demands on KIPPRA at a time when it is trying to recover from the senior staff turnover suffered in ...

  4. Office of Research Support | College of Engineering & Applied Science

    Science.gov (United States)

    Professor and Associate Dean for Research College of Engineering and Applied Sciences Director, Center for Academics Admission Student Life Research Schools & Colleges Libraries Athletics Centers & ; Applied Science Powerful Ideas. Proven Results. Search for: Go This site All UWM Search Site Menu Skip to

  5. Urban History in 4 Dimensions - Supporting Research and Education

    Science.gov (United States)

    Münster, S.; Friedrichs, K.; Kröber, C.; Bruschke, J.; Henze, F.; Maiwald, F.; Niebling, F.

    2017-08-01

    The new research group on the four-dimensional research and communication of urban history (Urban History 4D) aims to investigate and develop methods and technologies to access extensive repositories of historical media and their contextual information in a spatial model, with an additional temporal component. This will make content accessible to different target groups, researchers and the public, via a 4D browser. A location-dependent augmented-reality representation can be used as an information base, research tool, and means of communicating historical knowledge. The data resources for this research include extensive holdings of historical photographs of Dresden, which have documented the city over the decades, and digitized map collections from the Deutsche Fotothek (German photographic collection) platform. These will lay the foundation for a prototype model which will give users a virtual experience of historic parts of Dresden.

  6. URBAN HISTORY IN 4 DIMENSIONS – SUPPORTING RESEARCH AND EDUCATION

    Directory of Open Access Journals (Sweden)

    S. Münster

    2017-08-01

    Full Text Available The new research group on the four-dimensional research and communication of urban history (Urban History 4D aims to investigate and develop methods and technologies to access extensive repositories of historical media and their contextual information in a spatial model, with an additional temporal component. This will make content accessible to different target groups, researchers and the public, via a 4D browser. A location-dependent augmented-reality representation can be used as an information base, research tool, and means of communicating historical knowledge. The data resources for this research include extensive holdings of historical photographs of Dresden, which have documented the city over the decades, and digitized map collections from the Deutsche Fotothek (German photographic collection platform. These will lay the foundation for a prototype model which will give users a virtual experience of historic parts of Dresden.

  7. IAEA activities supporting the applications of research reactors in 2013

    International Nuclear Information System (INIS)

    Peld, N.D.; Ridikas, D.

    2014-01-01

    As the underutilization of research reactors around the world persists as a primary topic of concern among facility owners and operators, the IAEA responded in 2013 with a broad range of activities to address the planning, execution and improvement of many experimental techniques. The revision of two critical documents for planning and diversifying a facility's portfolio of applications, TECDOC 1234 'The Applications of Research Reactors' and TECDOC 1212 'Strategic Planning for Research Reactors', is in progress in order to keep this information relevant, corresponding to the dynamism of experimental techniques and research capabilities. Related to the latter TECDOC, the IAEA convened a meeting in 2013 for the expert review of a number of strategic plans submitted by research reactor operators in developing countries. A number of activities focusing on specific applications are either continuing or beginning as well. In neutron activation analysis, a joint round of inter-comparison proficiency testing sponsored by the IAEA Technical Cooperation Department will be completed, and facility progress in measurement accuracy is described. Also, a training workshop in neutron imaging and Coordinated Research Projects in reactor benchmarks, automation of neutron activation analysis and neutron beam techniques for material testing intend to advance these activities as more beneficial services to researchers and other users. (author)

  8. A theoretical framework to support research of health service innovation.

    Science.gov (United States)

    Fox, Amanda; Gardner, Glenn; Osborne, Sonya

    2015-02-01

    Health service managers and policy makers are increasingly concerned about the sustainability of innovations implemented in health care settings. The increasing demand on health services requires that innovations are both effective and sustainable; however, research in this field is limited, with multiple disciplines, approaches and paradigms influencing the field. These variations prevent a cohesive approach, and therefore the accumulation of research findings, in the development of a body of knowledge. The purpose of this paper is to provide a thorough examination of the research findings and provide an appropriate theoretical framework to examine sustainability of health service innovation. This paper presents an integrative review of the literature available in relation to sustainability of health service innovation and provides the development of a theoretical framework based on integration and synthesis of the literature. A theoretical framework serves to guide research, determine variables, influence data analysis and is central to the quest for ongoing knowledge development. This research outlines the sustainability of innovation framework; a theoretical framework suitable for examining the sustainability of health service innovation. If left unaddressed, health services research will continue in an ad hoc manner, preventing full utilisation of outcomes, recommendations and knowledge for effective provision of health services. The sustainability of innovation theoretical framework provides an operational basis upon which reliable future research can be conducted.

  9. Research success and structured support: Developing early career ...

    African Journals Online (AJOL)

    This article discusses the programme structure, participants' evaluation of the year-long intervention and longitudinal data from a follow-up study conducted in 2008. It is evident in studies conducted in South Africa (Geber 2006) and elsewhere (Sorcinelli 2000) that support including mentoring and coaching is necessary for ...

  10. Supporting research in Brazilian agriculture and the Amazon Basin

    International Nuclear Information System (INIS)

    Munoz-Ribadeneira, F.J.

    1989-01-01

    Isotope experiments in agriculture have been carried out in Brazil since 1954. Since 1982, the IAEA has supported the agricultural sciences in Brazil through the projects financed under the IAEA's technical assistance and co-operation programme. These projects include: Radioisotopes in Agriculture; Biological Nitrogen Fixation; Animal Science; Medfly Eradication; and Soil Formation and Degradation. 26 refs, 6 figs, 1 tab

  11. Space Weather Forecasting and Supporting Research in the USA

    Science.gov (United States)

    Pevtsov, A. A.

    2017-12-01

    In the United State, scientific research in space weather is funded by several Government Agencies including the National Science Foundation (NSF) and the National Aeronautics and Space Agency (NASA). For civilian and commercial purposes, space weather forecast is done by the Space Weather Prediction Center (SWPC) of the National Oceanic and Atmospheric Administration (NOAA). Observational data for modeling come from the network of groundbased observatories funded via various sources, as well as from the instruments on spacecraft. Numerical models used in forecast are developed in framework of individual research projects. The article provides a brief review of current state of space weather-related research and forecasting in the USA.

  12. On network coding and modulation mapping for three-phase bidirectional relaying

    KAUST Repository

    Chang, Ronald Y.; Lin, Sian Jheng; Chung, Wei-Ho

    2015-01-01

    © 2015 IEEE. In this paper, we consider the network coding (NC) enabled three-phase protocol for information exchange between two users in a wireless two-way (bidirectional) relay network. Modulo-based (nonbinary) and XOR-based (binary) NC schemes are considered as information mixture schemes at the relay while all transmissions adopt pulse amplitude modulation (PAM). We first obtain the optimal constellation mapping at the relay that maximizes the decoding performance at the users for each NC scheme. Then, we compare the two NC schemes, each in conjunction with the optimal constellation mapping at the relay, in different conditions. Our results demonstrate that, in the low SNR regime, binary NC outperforms nonbinary NC with 4-PAM, while they have mixed performance with 8-PAM. This observation applies to quadrature amplitude modulation (QAM) composed of two parallel PAMs.

  13. Absorption in a three-phase fluidized bed I: Hydrodynamic investigations

    Directory of Open Access Journals (Sweden)

    Pejanović Srđan M.

    2003-01-01

    Full Text Available The hydrodynamic properties of a three phase fluidized bed with low density inert spherical packing, fluidized by the interaction of a gas flowing upwards and a liquid flowing downwards through the column, were investigated. It was found that the pressure drop, liquid hold up and dynamic bed height increase with both increasing liquid and gas flow rate. While the dynamic bed height and minimum fluidization velocity remain unchanged, both the pressure drop and liquid hold up increase with increasing density of the packing. Therefore, an increase in packing density causes more intensive mass transfer between the fluid phases than packed columns. It was shown that increase of the liquid flow rate causes an increase of both the effective liquid and gas velocity through the fluidized bed, which may also improve mass transfer.

  14. A zero-voltage-switched three-phase interleaved buck converter

    Science.gov (United States)

    Hsieh, Yao-Ching; Huang, Bing-Siang; Lin, Jing-Yuan; Pham, Phu Hieu; Chen, Po-Hao; Chiu, Huang-Jen

    2018-04-01

    This paper proposes a three-phase interleaved buck converter which is composed of three identical paralleled buck converters. The proposed solution has three shunt inductors connected between each other of three basic buck conversion units. With the help of the shunt inductors, the MOSFET parasitic capacitances will resonate to achieve zero-voltage-switching. Furthermore, the decreasing rate of the current through the free-wheeling diodes is limited, and therefore, their reverse-recovery losses can be minimised. The active power switches are controlled by interleaved pulse-width modulation signals to reduce the input and output current ripples. Therefore, the filtering capacitances on the input and output sides can be reduced. The power efficiency is measured to be as high as 98% in experiment with a prototype circuit.

  15. Hysteresis Control for Shunt Active Power Filter under Unbalanced Three-Phase Load Conditions

    Directory of Open Access Journals (Sweden)

    Z. Chelli

    2015-01-01

    Full Text Available This paper focuses on a four-wire shunt active power filter (APF control scheme proposed to improve the performance of the APF. This filter is used to compensate harmonic distortion in three-phase four-wire systems. Several harmonic suppression techniques have been widely proposed and applied to minimize harmonic effects. The proposed control scheme can compensate harmonics and reactive power of the nonlinear loads simultaneously. This approach is compared to the conventional shunt APF reference compensation strategy. The developed algorithm is validated by simulation tests using MATLAB Simulink. The obtained results have demonstrated the effectiveness of the proposed scheme and confirmed the theoretical developments for balanced and unbalanced nonlinear loads.

  16. A Navier-Stokes/Cahn-Hilliard model for the simulation of three phase immiscible incompressible flows

    International Nuclear Information System (INIS)

    Celine Lapuerta; Bruno Piar; Franck Boyer; Philippe Angot; Michel Quintard

    2005-01-01

    This paper presents a Navier-Stokes/Cahn-Hilliard model designed for incompressible flows of three immiscible phases, characterized by different surface tensions and without phase change. This physical context is relevant to study the late phase of a hypothetical severe accident in a nuclear pressurized water reactor. Thanks to a suitable choice of a free energy and a particular form of the Cahn-Hilliard equation, the evolution of the three phases is described by only two order parameters. Moreover, this model allows the simulation of purely two phase flows as a limiting case: no artificial apparition of the third phase occurs if this later is physically absent which contrasts with others models of the literature. We examine the spreading of a liquid lens at the interface between two stratified phases. We present results showing that the method gives correct contact angles and pressure jumps, at equilibrium. (authors)

  17. High efficiency and long life of a three-phase power conditioner via interleave control

    Directory of Open Access Journals (Sweden)

    Kenji Amei

    2016-01-01

    Full Text Available This study describes the high efficiency and long life of three-phase power conditioners of a photovoltaic (PV system. The current PV system, which is widely spread, has two problems. The first problem is the lifetime of a power conditioner, whereas the other problem is the drop in the efficiency of the conversion because of the characteristics of the solar cell. For those problems, the solar panel and boost chopper circuit were divided into a plurality to configure a power conditioner, and an electrolytic capacitor-less driver with interleave control was realized. The drop in the current generated by the solar cell was suppressed, and an improvement in power generation efficiency was expected. The configuration and principle of a proposed circuit were explained, and results of simulation and experiment were reported.

  18. Three-Phase Melting Curves in the Binary System of Carbon Dioxide and Water

    Science.gov (United States)

    Abramson, E. H.

    2017-10-01

    Invariant, three-phase melting curves, of ice VI in equilibrium with solid CO2, of ice VII in equilibrium with solid CO2, and of solid CO2 in simultaneous equilibrium with a majority aqueous and a majority CO2 fluid, were explored in the binary system of carbon dioxide and water. Diamond-anvil cells were used to develop pressures of 5 GPa. Water exhibits a large melting temperature depression (73°C less than its pure melting temperature of 253°C at 5 GPa) indicative of large concentrations of CO2 in the aqueous solution. The melting point of water-saturated CO2 does not show a measureable departure from that of the pure system at temperatures lower than ∼200°C and only 10°C at 5 GPa (from 327°C).

  19. Modeling of a three-phase reactor for bitumen-derived gas oil hydrotreating

    International Nuclear Information System (INIS)

    Chacon, R.; Canale, A.; Bouza, A.; Sanchez, Y.

    2012-01-01

    A three-phase reactor model for describing the hydrotreating reactions of bitumen-derived gas oil was developed. The model incorporates the mass-transfer resistance at the gas-liquid and liquid-solid interfaces and a kinetic rate expression based on a Langmuir-Hinshelwood-type model. We derived three correlations for determining the solubility of hydrogen (H 2 ), hydrogen sulfide (H 2 S) and ammonia (NH 3 ) in hydrocarbon mixtures and the calculation of the catalyst effectiveness factor was included. Experimental data taken from the literature were used to determine the kinetic parameters (stoichiometric coefficients, reaction orders, reaction rate and adsorption constants for hydrodesulfuration (HDS) and hydrodenitrogenation (HDN)) and to validate the model under various operating conditions. Finally, we studied the effect of operating conditions such as pressure, temperature, LHSV, H 2 /feed ratio and the inhibiting effect of H 2 S on HDS and NH 3 on HDN. (author)

  20. The three phases of time-limited day-hospital treatment.

    Science.gov (United States)

    Stein, H H; Hirsch, B; Brenman, S; Bataclan, L

    1990-06-01

    The course of treatment in a time-limited day-hospital setting can be usefully understood in terms of three phases. Close examination of the treatment goals, difficulties, benefits, and tasks for both patients and staff for each phase provides a greater understanding of the curative process. These observations are based upon clinical work in a Veteran Administration Day Hospital and are reinforced with clinical examples from that work. Identification of these phases of treatment can be put to practical use. Knowing in which phase a patient is working helps staff members focus their thinking. Such an awareness can also help staff members cope with "burnout" over the frustrations that come with a particular phase. Information about these phases has been valuable to patients and their families in helping them understand the course of their treatment.

  1. High accuracy interface characterization of three phase material systems in three dimensions

    DEFF Research Database (Denmark)

    Jørgensen, Peter Stanley; Hansen, Karin Vels; Larsen, Rasmus

    2010-01-01

    Quantification of interface properties such as two phase boundary area and triple phase boundary length is important in the characterization ofmanymaterial microstructures, in particular for solid oxide fuel cell electrodes. Three-dimensional images of these microstructures can be obtained...... by tomography schemes such as focused ion beam serial sectioning or micro-computed tomography. We present a high accuracy method of calculating two phase surface areas and triple phase length of triple phase systems from subvoxel accuracy segmentations of constituent phases. The method performs a three phase...... polygonization of the interface boundaries which results in a non-manifold mesh of connected faces. We show how the triple phase boundaries can be extracted as connected curve loops without branches. The accuracy of the method is analyzed by calculations on geometrical primitives...

  2. A new PWM algorithm for battery-source three-phase inverters

    Energy Technology Data Exchange (ETDEWEB)

    Chan, C.C. (Dept. of Electrical and Electronic Engineering, Univ. of Hong Kong, Pokfulam Road (HK)); Chau, K.T. (Dept. of Electrical Engineering, Hong Kong Polytechnic, Hung Hom (HK))

    1991-01-01

    A new PWM algorithm for battery-source three-phase inverters is described in this paper. The concept of the algorithm is to determine the pulsewidths by equating the areas of the segments of the sinusodial reference with the related output pulse areas. The algorithm is particularly suitable to handle a non-constant voltage source with good harmonic suppression. Since the pulsewidths are computable in real time with minimal storage requirement as well as compact hardware and software, it is especially suitable for single-chip microcomputer implementation. Experimental results show that the single-chip microcomputer Intel 8095-based battery-source inverter can control a 3 kW synchronous motor drive satisfactorily over a frequency range of 2 to 100Hz.

  3. A Coordinate Control Strategy for Circulating Current Suppression in Multiparalleled Three-Phase Inverters

    DEFF Research Database (Denmark)

    Zhang, Xueguang; Wang, Tianyi; Wang, Xiongfei

    2017-01-01

    This paper addresses the zero-sequence circulating current control in the multiparalleled three-phase voltage-source inverters. The model of the zero-sequence circulating current in the N-paralleled (N ≥ 3) inverters is derived. It is shown that the circulating current is not only susceptible...... to the mismatches of circuit parameters, but it is also influenced by the interactions of circulating current controllers used by other paralleled inverters. To eliminate these adverse effects on the circulating current control loop, a coordinate control strategy for the N-paralleled inverter is proposed based...... on the zero-vector feedforward method with the space-vector pulse width modulation. Moreover, a virtual inverter method is introduced to facilitate the implementation of the proposed controller, which decouples the interactions of circulating current controllers in the paralleled inverters. Finally...

  4. Three-phase model and power-flow analysis of microgrids and virtual power plants

    Energy Technology Data Exchange (ETDEWEB)

    Kamh, M.Z.; Iravani, R. [Toronto Univ., ON (Canada). Dept. of Electrical and Computer Engineering, Energy Systems Group

    2009-07-01

    A distributed energy resources (DER) unit can be a distributed generation unit, a distributed storage unit, or a hybrid of the two. It can be dispatchable, non-dispatchable or pseudo-dispatchable. A DER unit is connected to the hosting utility directly or via an electronic converter. A three-phase model and power-flow analysis of microgrids and virtual power plants was presented. The presentation discussed DER classification; microgrids and virtual power plants; motivations and goals; and a proposed DER model and power flow approach. Validation and results were also offered. The developed algorithm was implemented in the sequence-component frame using the MATLAB platform. Case studies were offered in order to verify the accuracy of the DER model and the power-flow program. It was concluded that the developed software accommodates different DER configurations and accurately reflects their control strategies. figs.

  5. Renewable Distributed Generation Models in Three-Phase Load Flow Analysis for Smart Grid

    Directory of Open Access Journals (Sweden)

    K. M. Nor

    2013-11-01

    Full Text Available The paper presents renewable distributed generation  (RDG models as three-phase resource in load flow computation and analyzes their effect when they are connected in composite networks. The RDG models that have been considered comprise of photovoltaic (PV and wind turbine generation (WTG. The voltage-controlled node and complex power injection node are used in the models. These improvement models are suitable for smart grid power system analysis. The combination of IEEE transmission and distribution data used to test and analyze the algorithm in solving balanced/unbalanced active systems. The combination of IEEE transmission data and IEEE test feeder are used to test the the algorithm for balanced and unbalanced multi-phase distribution system problem. The simulation results show that by increased number and size of RDG units have improved voltage profile and reduced system losses.

  6. Four quadrant control circuit for a brushless three-phase dc motor

    Science.gov (United States)

    Nola, Frank J. (Inventor)

    1987-01-01

    A control circuit is provided for a brushless three-phase dc motor which affords four quadrant control from a single command. The control circuit probes acceleration of the motor in both clockwise and counterclockwise directions and braking and generation in both clockwise and counterclockwise directions. In addition to turning on individual transistors of the transistor pairs connected to the phase windings of the motor for 120 deg periods while the other transistor of that pair is off, the control circuit also provides, in a future mode of operation, turning the two transistors of each pair on and off alternately at a phase modulation frequency during such a 120 deg period. A feedback signal is derived which is proportional to the motor current and which has a polarity consistent with the command signal, such that negative feedback results.

  7. Optical measuring techniques and their application to two-phase and three-phase flows

    International Nuclear Information System (INIS)

    Liu Xiaozhi.

    1992-01-01

    First of all it is shown that by an optical system based on the Laser-Doppler technology, which uses a pair of cylindrical waves and two optical detectors, the particle size, speed and refractive index can be measured by means of the signal frequencies. The second optical method to characterize spherical particles in a multi-phase flow is an extended phase-Doppler system. By means of an additional pair of photodetectors it has been possible for the first time to measure the refractive index in addition to speed and particle size. The last part of the paper shows that by a special phase-Doppler anemometry system with only two detectors it is also possible to distinguish between reflecting and refractive particles. By means of such PDA system measurements were made in a gas-fluid-solid three-phase flow directed vertically upwards. (orig./DG) [de

  8. Stability of operation versus temperature of a three-phase clock-driven chaotic circuit

    International Nuclear Information System (INIS)

    Zhou Ji-Chao; Son Hyunsik; Song Han Jung; Kim Namtae

    2013-01-01

    We evaluate the influence of temperature on the behavior of a three-phase clock-driven metal—oxide—semiconductor (MOS) chaotic circuit. The chaotic circuit consists of two nonlinear functions, a level shifter, and three sample and hold blocks. It is necessary to analyze a CMOS-based chaotic circuit with respect to variation in temperature for stability because the circuit is sensitive to the behavior of the circuit design parameters. The temperature dependence of the proposed chaotic circuit is investigated via the simulation program with integrated circuit emphasis (SPICE) using 0.6-μm CMOS process technology with a 5-V power supply and a 20-kHz clock frequency. The simulation results demonstrate the effects of temperature on the chaotic dynamics of the proposed chaotic circuit. The time series, frequency spectra, bifurcation phenomena, and Lyapunov exponent results are provided. (general)

  9. ANN based controller for three phase four leg shunt active filter for power quality improvement

    Directory of Open Access Journals (Sweden)

    J. Jayachandran

    2016-03-01

    Full Text Available In this paper, an artificial neural network (ANN based one cycle control (OCC strategy is proposed for the DSTATCOM shunted across the load in three phase four wire distribution system. The proposed control strategy mitigates harmonic/reactive currents, ensures balanced and sinusoidal source current from the supply mains that are nearly in phase with the supply voltage and compensates neutral current under varying source and load conditions. The proposed control strategy is superior over conventional methods as it eliminates, the sensors needed for sensing load current and coupling inductor current, in addition to the multipliers and the calculation of reference currents. ANN controllers are implemented to maintain voltage across the capacitor and as a compensator to compensate neutral current. The DSTATCOM performance is validated for all possible conditions of source and load by simulation using MATLAB software and simulation results prove the efficacy of the proposed control over conventional control strategy.

  10. Microcontroller based PWM controlled four switch three phase inverter fed induction motor drive

    Directory of Open Access Journals (Sweden)

    Mohanty Kant Nalin

    2010-01-01

    Full Text Available This paper presents PIC microcontroller based PWM inverter controlled four switch three phase inverter (FSTPI fed Induction Motor drive. The advantage of this inverter that uses of 4 switches instead of conventional 6 switches is lesser switching losses, lower electromagnetic interference (EMI, less complexity of control algorithms and reduced interface circuits. Simulation and experimental work are carried out and results presented to demonstrate the feasibility of the proposed approach. Simulation is carried out using MATLAB SIMULINK and in the experimental work a prototype model is built to verify the simulation results. PIC microcontroller (PIC 16F877A is used to generate the PWM pulses for FSTPI to drive the 0.5 hp 3-phase Induction Motor.

  11. Power Controllability of Three-phase Converter with Unbalanced AC Source

    DEFF Research Database (Denmark)

    Ma, Ke; Liserre, Marco; Blaabjerg, Frede

    2013-01-01

    Three-phase DC-AC power converters suffer from power oscillation and overcurrentt problems in case of unbalanced AC source voltage that can be caused by grid/generator faults. Existing solutions to handle these problems are properly selecting and controlling the positive and negative sequence...... currents. In this work a new series of control strategies which utilize the zero-sequence components are proposed to enhance the power control ability under this adverse conditions. It is concluded that by introducing proper zero sequence current controls and corresponding circuit configurations, the power...... converter can enable more flexible control targets, achieving better performances in the delivered power and load current when suffering from unbalanced AC sources....

  12. Power Controllability of Three-phase Converter with Unbalanced AC Source

    DEFF Research Database (Denmark)

    Ma, Ke; Chen, Wenjie; Liserre, Marco

    2015-01-01

    Three-phase DC-AC power converters suffer from power oscillation and overcurrent problems in case of unbalanced AC source voltage that can be caused by grid/generator faults. Existing solutions to handle these problems are properly selecting and controlling the positive and negative sequence...... currents. In this work a new series of control strategies which utilize the zerosequence components are proposed to enhance the power control ability under this adverse condition. It is concluded that by introducing proper zero sequence current controls and corresponding circuit configurations, the power...... converter can enable more flexible control targets, achieving better performances in the delivered power and load current when suffering from unbalanced AC voltage....

  13. Design and control of an LCL-filter-based three-phase active rectifier

    DEFF Research Database (Denmark)

    Liserre, Marco; Blaabjerg, Frede; Hansen, Steffan

    2005-01-01

    This paper proposes a step-by-step procedure for designing the LCL filter of a front-end three-phase active rectifier. The primary goal is to reduce the switching frequency ripple at a reasonable cost, while at the same time achieving a high-performance front-end rectifier (as characterized...... by a rapid dynamic response and good stability margin). An example LCL filter design is reported and a filter has been built and tested using the values obtained from this design. The experimental results demonstrate the performance of the design procedure both for the LCL filter and for the rectifier...... a powerful tool to design an LCL-filter-based active rectifier while avoiding trial-and-error procedures that can result in having to build several filter prototypes....

  14. Sliding three-phase contact line of printed droplets for single-crystal arrays

    International Nuclear Information System (INIS)

    Kuang, Minxuan; Wu, Lei; Li, Yifan; Gao, Meng; Zhang, Xingye; Jiang, Lei; Song, Yanlin

    2016-01-01

    Controlling the behaviours of printed droplets is an essential requirement for inkjet printing of delicate three-dimensional (3D) structures or high-resolution patterns. In this work, molecular deposition and crystallization are regulated by manipulating the three-phase contact line (TCL) behaviour of the printed droplets. The results show that oriented single-crystal arrays are fabricated based on the continuously sliding TCL. Owing to the sliding of the TCL on the substrate, the outward capillary flow within the evaporating droplet is suppressed and the molecules are brought to the centre of the droplet, resulting in the formation of a single crystal. This work provides a facile strategy for controlling the structures of printed units by manipulating the TCL of printed droplets, which is significant for realizing high-resolution patterns and delicate 3D structures. (paper)

  15. Design and Control of Parallel Three Phase Voltage Source Inverters in Low Voltage AC Microgrid

    Directory of Open Access Journals (Sweden)

    El Hassane Margoum

    2017-01-01

    Full Text Available Design and hierarchical control of three phase parallel Voltage Source Inverters are developed in this paper. The control scheme is based on synchronous reference frame and consists of primary and secondary control levels. The primary control consists of the droop control and the virtual output impedance loops. This control level is designed to share the active and reactive power correctly between the connected VSIs in order to avoid the undesired circulating current and overload of the connected VSIs. The secondary control is designed to clear the magnitude and the frequency deviations caused by the primary control. The control structure is validated through dynamics simulations.The obtained results demonstrate the effectiveness of the control structure.

  16. Comparative Study of Fault Diagnostic Methods in Voltage Source Inverter Fed Three Phase Induction Motor Drive

    Science.gov (United States)

    Dhumale, R. B.; Lokhande, S. D.

    2017-05-01

    Three phase Pulse Width Modulation inverter plays vital role in industrial applications. The performance of inverter demeans as several types of faults take place in it. The widely used switching devices in power electronics are Insulated Gate Bipolar Transistors (IGBTs) and Metal Oxide Field Effect Transistors (MOSFET). The IGBTs faults are broadly classified as base or collector open circuit fault, misfiring fault and short circuit fault. To develop consistency and performance of inverter, knowledge of fault mode is extremely important. This paper presents the comparative study of IGBTs fault diagnosis. Experimental set up is implemented for data acquisition under various faulty and healthy conditions. Recent methods are executed using MATLAB-Simulink and compared using key parameters like average accuracy, fault detection time, implementation efforts, threshold dependency, and detection parameter, resistivity against noise and load dependency.

  17. Power Factor Correction Capacitors for Multiple Parallel Three-Phase ASD Systems

    DEFF Research Database (Denmark)

    Yang, Yongheng; Blaabjerg, Frede

    2017-01-01

    Today’s three-phase Adjustable Speed Drive (ASD) systems still employ Diode Rectifiers (DRs) and Silicon-Controlled Rectifiers (SCRs) as the front-end converters due to structural and control simplicity, small volume, low cost, and high reliability. However, the uncontrollable DRs and phase......-controllable SCRs bring side-effects by injecting high harmonics to the grid, which will degrade the system performance in terms of lowering the overall efficiency and overheating the system if remain uncontrolled or unattenuated. For multiple ASD systems, certain harmonics in the entire system can be mitigated...... the power factor, passive capacitors can be installed, which yet can trigger the system resonance. Hence, this paper analyzes the resonant issues in multiple ASD systems with power factor correction capacitors. Potential damping solutions are summarized. Simulations are carried out, while laboratory tests...

  18. Power-Quality-Oriented Optimization in Multiple Three-Phase Adjustable Speed Drives

    DEFF Research Database (Denmark)

    Yang, Yongheng; Davari, Pooya; Blaabjerg, Frede

    2016-01-01

    As an almost standardized configuration, Diode Rectifiers (DRs) and Silicon-Controlled Rectifiers (SCRs) are commonly employed as the front-end topology in three-phase Adjustable Speed Drive (ASD) systems. Features of this ASD configuration include: structural and control simplicity, small volume......, low cost, and high reliability during operation. Yet, DRs and SCRs bring harmonic distortions in the mains and thus lowering the overall efficiency. Power quality standards/rules are thus released. For multiple ASD systems, certain harmonics of the total grid current can be mitigated by phase......-shifting the currents drawn by SCR-fed drives, and thus it is much flexible to reduce the Total Harmonic Distortion (THD) level in such applications. However, the effectiveness of this harmonic mitigation scheme for multiple ASD systems depends on: a) the number of parallel drives, b) the power levels, and c...

  19. Estimated D2--DT--T2 phase diagram in the three-phase region

    International Nuclear Information System (INIS)

    Souers, P.C.; Hickman, R.G.; Tsugawa, R.T.

    1976-01-01

    A composite of experimental eH 2 -D 2 phase-diagram data at the three-phase line is assembled from the literature. The phase diagram is a smooth cigar shape without a eutectic point, indicating complete miscibility of liquid and solid phases. Additional data is used to estimate the D 2 -T 2 , D 2 DT, and DT-T 2 binary phase diagrams. These are assembled into the ternary D 2 -DT-T 2 phase diagram. A surface representing the chemical equilibrium of the three species is added to the phase diagram. At chemical equilibrium, it is estimated that 50-50 liquid D-T at 19.7 0 K is in equilibrium with 42 mole percent T vapor and 54 percent T solid. Infrared spectroscopy is suggested as a means of component analysis of liquid and solid mixtures

  20. Real time EM waves monitoring system for oil industry three phase flow measurement

    International Nuclear Information System (INIS)

    Al-Hajeri, S; Wylie, S R; Shaw, A; Al-Shamma'a, A I

    2009-01-01

    Monitoring fluid flow in a dynamic pipeline is a significant problem in the oil industry. In order to manage oil field wells efficiently, the oil industry requires accurate on line sensors to monitor the oil, gas, and water flow in the production pipelines. This paper describes a non-intrusive sensor that is based on an EM Waves cavity resonator. It determines and monitors the percentage volumes of each phase of three phase (oil, gas, and water) in the pipeline, using the resonant frequencies shifts that occur within an electromagnetic cavity resonator. A laboratory prototype version of the sensor system was constructed, and the experimental results were compared to the simulation results which were obtained by the use of High Frequency Structure Simulation (HFSS) software package.

  1. A vector modulated three-phase four-quadrant rectifier - Application to a dc motor drive

    Energy Technology Data Exchange (ETDEWEB)

    Jussila, Matti; Salo, Mika; Kaehkoenen, Lauri; Tuusa, Heikki

    2004-07-01

    This paper introduces a theory for a space vector modulation of a three-phase four-quadrant PWM rectifier (FQR). The presented vector modulation method is simple to realize with a microcontroller and it replaces the conventional modulation methods based on the analog technology. The FQR may be used to supply directly a dc load, e.g. a dc machine. The vector modulated FQR is tested in simulations supplying a 4.5 kW dc motor. The simulations show the benefits of the vector modulated FQR against thyristor converters: the supply currents are sinusoidal and the displacement power factor of the supply can be controlled. Furthermore the load current is smooth. (author)

  2. Determining the magnetically nonlinear characteristics of a three phase core-type power transformer

    International Nuclear Information System (INIS)

    Dolinar, Matjaz; Stumberger, Gorazd; Polajzer, Bostjan; Dolinar, Drago

    2006-01-01

    This paper presents nonlinear iron core model of a three-phase, three-limb power transformer which is given by the current-dependant characteristics of flux linkages. The magnetically nonlinear characteristics are determined by controlled magnetic excitation of all three limbs which allows to take into account the variable magnetic-cross couplings between different coils placed on limbs, caused by saturation. The corresponding partial derivatives of measured flux linkage characteristics are used in the transformer circuit model as a magnetically nonlinear iron core model in order to analyze the behaviour of a nonsymmetrically excited transformer. Numerical results using transformer model with the determined iron core model agree very well with the measured results

  3. On network coding and modulation mapping for three-phase bidirectional relaying

    KAUST Repository

    Chang, Ronald Y.

    2015-12-03

    © 2015 IEEE. In this paper, we consider the network coding (NC) enabled three-phase protocol for information exchange between two users in a wireless two-way (bidirectional) relay network. Modulo-based (nonbinary) and XOR-based (binary) NC schemes are considered as information mixture schemes at the relay while all transmissions adopt pulse amplitude modulation (PAM). We first obtain the optimal constellation mapping at the relay that maximizes the decoding performance at the users for each NC scheme. Then, we compare the two NC schemes, each in conjunction with the optimal constellation mapping at the relay, in different conditions. Our results demonstrate that, in the low SNR regime, binary NC outperforms nonbinary NC with 4-PAM, while they have mixed performance with 8-PAM. This observation applies to quadrature amplitude modulation (QAM) composed of two parallel PAMs.

  4. High-frequency, three-phase current controller implementation in an FPGA

    Energy Technology Data Exchange (ETDEWEB)

    Hartmann, M.; Round, S. D.; Kolar, J. W.

    2008-07-01

    Three phase rectifiers with switching frequencies of 500 kHz or more require high speed current controllers. At such high switching frequencies analog controllers as well as high speed digital signal processing (DSP) systems have limited performance. In this paper, two high speed current controller implementations using two different field-programmable gate arrays (FPGA) - one for switching frequencies up to 1 MHz and one for switching frequencies beyond 1 MHz - are presented to overcome this performance limitation. Starting with the digital system design all the blocks of the signal chain, containing analog-to-digital (A/D) interface, digital controller implementation using HW-multipliers and implementation of a novel high speed, high resolution pulse width modulation (PWM) are discussed and compared. Final measurements verify the performance of the controllers. (author)

  5. Fault Diagnosis of Low-Power Three-Phase Induction Motor

    Directory of Open Access Journals (Sweden)

    Gedzurs Aleksejs

    2016-12-01

    Full Text Available An Induction motor reliability survey at an egg processing plant shows that almost 50% of the total motor failures are fan induction motors. Visual investigations of the faulty fan motors show that the main cause of the induction motor failure is air gap eccentricity. In this study, experimental tests are performed on a 1.1kW three-phase induction motor to detect air gap eccentricity and overheating of the induction motor. Heating tests show that end shield housing temperature reaches 100°C with blocked air flow from the fan, which can reduce the lifespan of the bearing. Dimension measurements of the end shield housing show that the dimensions of both tested motors back-end shields are larger than ISO tolerance grade limit. It leads to a loose fit between the housing and bearing, causing air gap eccentricity. Also, both motor back end shield housing has an out-of-round condition leading to an unbalanced magnetic pull. To detect the air gap eccentricity caused by too loose of a fit between housing bore and bearing, current Park’s vector approach is used. To measure three phase current, Hall Effect current transducers, a digital oscilloscope is used and Matlab software to process the measurement data. Results show that Park’s vector approach can be used to detect the air gap eccentricity caused by too loose a fit between bearing and housing. Therefore, the Park’s vector approach can be used to diagnose air gap eccentricity and analyse the type of the air gap eccentricity.

  6. Supporting Informed Decision Making - Center for Research Strategy

    Science.gov (United States)

    CRS conducts portfolio analyses and collects data on scientific topics, funding mechanisms, and investigator characteristics to help NCI leadership make data-driven decisions about the scientific research enterprise.

  7. NRC safety research in support of regulation, FY 1992

    International Nuclear Information System (INIS)

    1993-05-01

    This report, the eighth in a series of annual reports, was prepared in response to congressional inquiries concerning how nuclear regulatory research is used. It summarizes the accomplishments of the Office of Nuclear Regulatory Research during FY 1992. A special emphasis on accomplishments in nuclear power plant aging research reflects recognition that a number of plants are entering the final portion of their original 40-year operating licenses and that, in addition to current aging effects, a focus on safety considerations for license renewal becomes timely. The primary purpose of performing regulatory research is to develop and provide the Commission and its staff with the technical bases for regulatory decisions on the safe operation of licensed nuclear reactors and facilities, to find unknown or unexpected safety problems, and to develop data and related information for the purpose of revising the Commission's rules, regulatory guides, or other guidance

  8. TTI Phase 2 Institutional Support: Ethiopian Development Research ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    Performance and policy engagement ... -increase researchers' ability to use innovative and advanced analytic techniques to provide policy guidance to the government of ... -improve organizational, financial management, and audit systems

  9. TTI Phase 2 Institutional Support: Ethiopian Development Research ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    Performance and policy engagement ... -increase researchers' ability to use innovative and advanced analytic techniques to provide policy ... -improve organizational, financial management, and audit systems ... Bulletin de BRAS - mai 2018.

  10. TTI Phase 2 Institutional Support: Economic and Social Research ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    The foundation aims to build capacity in economic and social policy analysis and development management. Its work ... -increase research staff retention rates ... IWRA/IDRC webinar on climate change and adaptive water management.

  11. Research Note: Headteacher Support Groups Initiative within the ...

    African Journals Online (AJOL)

    Eastern Africa Social Science Research Review. Journal Home · ABOUT THIS JOURNAL · Advanced Search · Current Issue · Archives · Journal Home > Vol 18, No 1 (2002) >. Log in or Register to get access to full text downloads.

  12. Institutional Support : Consortium for Economic and Social Research ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    They have contributed to the design of the 10-year education development program ... is the most promising policy research organization in Sénégal today. ... planning process and strengthen its governance structures, its management ...

  13. Chemical Safety Research Advances in Support of Lautenberg Act

    Science.gov (United States)

    EPA researchers are developing new ways to identify which chemicals to prioritize for further testing, to provide better access to information about chemicals, and to understand what potential risks chemicals may pose to humans and the environment.

  14. Institutional Support to South Asian Policy Research Organizations ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    There are very few policy research organizations in South Asia outside India. ... Call for new OWSD Fellowships for Early Career Women Scientists now open ... IWRA/IDRC webinar on climate change and adaptive water management.

  15. ABA-Cloud: support for collaborative breath research.

    Science.gov (United States)

    Elsayed, Ibrahim; Ludescher, Thomas; King, Julian; Ager, Clemens; Trosin, Michael; Senocak, Uygar; Brezany, Peter; Feilhauer, Thomas; Amann, Anton

    2013-06-01

    This paper introduces the advanced breath analysis (ABA) platform, an innovative scientific research platform for the entire breath research domain. Within the ABA project, we are investigating novel data management concepts and semantic web technologies to document breath analysis studies for the long run as well as to enable their full automatic reproducibility. We propose several concept taxonomies (a hierarchical order of terms from a glossary of terms), which can be seen as a first step toward the definition of conceptualized terms commonly used by the international community of breath researchers. They build the basis for the development of an ontology (a concept from computer science used for communication between machines and/or humans and representation and reuse of knowledge) dedicated to breath research.

  16. Research to support development of organic food and farming

    OpenAIRE

    Watson, Christine; Alrøe, Hugo; Kristensen, Erik Steen

    2006-01-01

    Agriculture and organic agriculture in particular are developing rapidly, due not only to technological change but also to changes in agricultural policy and public expectation. Research allows new knowledge to be developed and is thus vital for the future of organic agriculture. We can ask the question, what is the purpose of research on organic farming? Is it to increase yield and productivity, to compare it with other forms of agriculture, or to quantify its environmental and social impact...

  17. Storytelling to support watershed research on emerging issues

    Science.gov (United States)

    Phillip Hellman

    2016-01-01

    Projections of budget deficits by the Congressional Budget Office imply ever-increasing pressure on federal spending for all purposes, including long-term watershed research. This presentation will argue that, since federal funding is ultimately a political decision, those responsible for maintaining long-term watershed research programs should not try to provide ...

  18. The verification of neutron activation analysis support system (cooperative research)

    Energy Technology Data Exchange (ETDEWEB)

    Sasajima, Fumio; Ichimura, Shigeju; Ohtomo, Akitoshi; Takayanagi, Masaji [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment; Sawahata, Hiroyuki; Ito, Yasuo [Tokyo Univ. (Japan). Research Center for Nuclear Science and Technology; Onizawa, Kouji [Radiation Application Development Association, Tokai, Ibaraki (Japan)

    2000-12-01

    Neutron activation analysis support system is the system in which even the user who has not much experience in the neutron activation analysis can conveniently and accurately carry out the multi-element analysis of the sample. In this verification test, subjects such functions, usability, precision and accuracy of the analysis and etc. of the neutron activation analysis support system were confirmed. As a method of the verification test, it was carried out using irradiation device, measuring device, automatic sample changer and analyzer equipped in the JRR-3M PN-3 facility, and analysis software KAYZERO/SOLCOI based on the k{sub 0} method. With these equipments, calibration of the germanium detector, measurement of the parameter of the irradiation field and analysis of three kinds of environmental standard sample were carried out. The k{sub 0} method adopted in this system is primarily utilized in Europe recently, and it is the analysis method, which can conveniently and accurately carried out the multi-element analysis of the sample without requiring individual comparison standard sample. By this system, total 28 elements were determined quantitatively, and 16 elements with the value guaranteed as analytical data of the NIST (National Institute of Standards and Technology) environment standard sample were analyzed in the accuracy within 15%. This report describes content and verification result of neutron activation support system. (author)

  19. Transportation research activities in support of nuclear waste management programs

    International Nuclear Information System (INIS)

    Allen, G.C. Jr.; Cashwell, J.W.; Jefferson, R.M.

    1983-01-01

    Transportation Technology Center has been conducting a wide range of technical research activities to assure the ability to transport radioactive materials in a safe, reliable manner. These activities include tasks in basic, analysis methodology and system research areas. Recently, the requirements of defense waste shipments have served as a focal point for development tasks with the expectation that they would serve as a precursor for commercial activities. The passage of the Nuclear Waste Policy Act has placed additional responsibility on the Department of Energy for concerns involving the shipments of civilian materials. The development of additional research responsibilities is expected to proceed concurrently with the evolution of the transportation mission plan for civilian spent fuel and high-level wastes

  20. Supporting robotics technology requirements through research in intelligent machines

    Energy Technology Data Exchange (ETDEWEB)

    Mann, R.C.

    1995-02-01

    {open_quotes}Safer, better, cheaper{close_quotes} are recurring themes in many robot development efforts. Significant improvements are being accomplished with existing technology, but basic research sets the foundations for future improvements and breakthrough discoveries. Advanced robots represent systems that integrate the three basic functions of sensing, reasoning, and acting (locomotion and manipulation) into one functional unit. Depending on the application requirements, some of these functions are implemented at a more or less advanced level than others. For example, some navigation tasks can be accomplished with purely reactive control and do not require sophisticated reasoning and planning methodologies. Robotics work at the Oak Ridge National Laboratory (ORNL) spans the spectrum from basic research to application-specific development and rapid prototyping of systems. This presentation summarizes recent highlights of the robotics research activities at ORNL.

  1. The professional research support in the 21st century

    DEFF Research Database (Denmark)

    Vinstrup, Anya Bjørn

    2010-01-01

    for research is becoming increasingly competitive and there is significant political influence on the scope and scale of funding programmes. This along with the ever more complicated and varied administrative procedures and demands for compliance both with pre-award and postaward activities has led...... between different researchers and professions and INTEGRATING disciplines throughout the entire value chain. • A profession that is only incipient regarding a formalised TRAINING but where there still are very high demands and expectations to their professional act. • IT is playing an increasing role...

  2. Instrumentation and control activities at the Electric Power Research Institute to support operator support systems

    International Nuclear Information System (INIS)

    Naser, J.

    1995-01-01

    Most nuclear power plants in the United States continue to operate with analog instrumentation and control (I and C) technology designed 20 to 40 years ago. This equipment is approaching or exceeding its life expectancy, resulting in increasing maintenance efforts to sustain system performance. Decreasing availability of replacement parts and the accelerating deterioration of the infrastructure of manufacturers that support analog technology exacerbate obsolescence problems and resultant operation and maintenance (O and M) cost increases. Modern digital technology holds a significant potential to improve the safety, cost-effectiveness, productivity, and, therefore, competitiveness of nuclear power plants. Operator support systems provide the tools to help achieve this potential. Reliable, integrated information is a critical element for protecting the utility's capital investment and increasing availability, reliability, and productivity. Integrated operator support systems with integrated information can perform more effectively to increase productivity, to enhance safety, and to reduce O and M costs. The plant communications and computing architecture is the infrastructure needed to allow the implementation of I and C systems and associated operator support systems in an integrated manner. Current technology for distributed digital systems, plant process computers, and plant communications and computing networks support the integration of systems and information. (author). 16 refs

  3. Impact of Three-Phase Relative Permeability and Hysteresis Models on Forecasts of Storage Associated With CO2-EOR

    Science.gov (United States)

    Jia, Wei; McPherson, Brian; Pan, Feng; Dai, Zhenxue; Moodie, Nathan; Xiao, Ting

    2018-02-01

    Geological CO2 sequestration in conjunction with enhanced oil recovery (CO2-EOR) includes complex multiphase flow processes compared to CO2 storage in deep saline aquifers. Two of the most important factors affecting multiphase flow in CO2-EOR are three-phase relative permeability and associated hysteresis, both of which are difficult to measure and are usually represented by numerical interpolation models. The purpose of this study is to improve understanding of (1) the relative impacts of different three-phase relative permeability models and hysteresis models on CO2 trapping mechanisms, and (2) uncertainty associated with these two factors. Four different three-phase relative permeability models and three hysteresis models were applied to simulations of an active CO2-EOR site, the SACROC unit located in western Texas. To eliminate possible bias of deterministic parameters, we utilized a sequential Gaussian simulation technique to generate 50 realizations to describe heterogeneity of porosity and permeability, based on data obtained from well logs and seismic survey. Simulation results of forecasted CO2 storage suggested that (1) the choice of three-phase relative permeability model and hysteresis model led to noticeable impacts on forecasted CO2 sequestration capacity; (2) impacts of three-phase relative permeability models and hysteresis models on CO2 trapping are small during the CO2-EOR injection period, and increase during the post-EOR CO2 injection period; (3) the specific choice of hysteresis model is more important relative to the choice of three-phase relative permeability model; and (4) using the recommended three-phase WAG (Water-Alternating-Gas) hysteresis model may increase the impact of three-phase relative permeability models and uncertainty due to heterogeneity.

  4. Usefulness of asymmetry score on quantitative three-phase bone scintigraphy in the evaluation of complex regional pain syndrome

    International Nuclear Information System (INIS)

    Sampath, Santhosh; Mittal, Bhagwant Rai; Arun, Sasikumar; Sood, Ashwani; Bhattacharya, Anish; Sharma, Aman

    2013-01-01

    Complex regional pain syndrome (CRPS) is primarily a clinical diagnosis. Diagnostic imaging in CRPS can be used, especially to exclude other disorders. The sensitivity and specificity of three phase bone scintigraphy (TPBS) for the diagnosis of CRPS is variable throughout the literature. To establish a simple and effective quantitative approach to help in the diagnosis of CRPS by TPBS. TPBS done in patients (n = 68) with suspected CRPS was analyzed retrospectively. They were classified into bone scan positive group (BSP), bone scan negative group (BSN) and non-CRPS group based on diffusely increased periarticular uptake, symmetrical uptake, and focal uptake respectively. Asymmetry score (AS) was also measured between the affected and unaffected side. 16 patients showed focal uptake, 37 were in BSP group with mean AS score of 1.57 ± 0.5 and 15 were in BSN group with mean AS score of 1.01 ± 0.05. The mean AS was significantly different (P < 0.0001). AS of 1.06 had sensitivity and specificity of 96.43% and 100% respectively (P = 0.0001). There was a trend of negative correlation between the AS and the duration, r = −0.21; however, it was not statistically significant (P = 0.28). TPBS should be considered in the evaluation of CRPS to rule out patients who have focal involvement, not diagnostic of CRPS (~24% in this study). Quantitative AS of 1.06 can be included to support visual interpretation in the delayed phase

  5. Instrumentation and control activities at the electric power research institute to support computerized support systems

    International Nuclear Information System (INIS)

    Naser, J.

    1996-01-01

    Most nuclear power plants in the United States are operating with their original analog I and C equipment. This equipment requires increasing maintenance efforts to sustain systems performance. Decreasing availability of replacement parts and support organization for analog technology accentuate obsolescence problems and resultant O and M cost increases. Modern technology, especially digital systems, offers improved functionality, performance, and reliability; solutions to obsolescence of equipment; reduction in O and M costs; and the potential to enhance safety. Digital systems, including computerized support systems, with their inherent advantages will be implemented only if reliable and cost-effective implementation and licensing acceptance is achieved and if the upgraded systems supports reduced power production costs. EPRI and its member utilities are working together under the Integrated I and C Upgrade Initiative to address I and C issues. (author). 23 refs

  6. Community-based health and schools of nursing: supporting health promotion and research.

    Science.gov (United States)

    Shannon, Crystal

    2014-01-01

    This article examines the role of community-based schools of nursing in the promotion of public health and research in poverty-stricken areas. This was a three-phase study (questionnaire and key-informants' interviews) that surveyed representatives of prelicensure associate and baccalaureate nursing schools (n=17), nursing-school key informants (n=6) and community leaders (n=10). A 13-question web-based survey and semi-structured interview of key informants elicited data on demographics, nursing program design, exposure of faculty and students to various research and health promotion methods, and beliefs about student involvement. Nursing schools participated minimally in community-based health promotion (CBHP) and community-based participatory research saw reduced need for student involvement in such activities, cited multiple barriers to active community collaboration, and reported restricted community partnerships. CBHP was recognized to be a valuable element of health care and student education, but is obstructed by many barriers. This study suggests that nursing schools are not taking full advantage of relationships with community leaders. Recommendations for action are given. © 2013 Wiley Periodicals, Inc.

  7. Spatial support of knowledge production in higher education : Research paper

    NARCIS (Netherlands)

    van Sprang, H; Groen, BH; van der Voordt, Theo

    2013-01-01

    This paper explores the impact of the physical and social dimensions of the work environment on satisfaction and perceived productivity of knowledge workers in Dutch universities of applied sciences. The approach took the form of a literature review, multiple case study of six research centres using

  8. Researchers urge climate-resilience support for South African maize ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    20 avr. 2016 ... Maize yields in parts of South Africa could decline by up to 20% by the 2050s as a result of climate change, research has shown. This could have a dramatic impact on subsistence farmers, with the poorest likely to be hardest hit. South Africa's Financial and Fiscal Commission tabled the findings for ...

  9. RIMISP Core Support for Rural Development Research (Latin ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    Specific objectives are to inform policymakers with strategic research on the dynamics of rural territories and the determinants of change; to build the capacity of ... Outputs. Papers. Equitierra : revista rural Latinoamericana, no. 2, enero 2009. 129956.pdf. Papers. Equitierra : revista rural Latinoamericana, no. 3, mayo 2009.

  10. Shared Journaling as Peer Support in Teaching Qualitative Research Methods

    Science.gov (United States)

    Humble, Aine M.; Sharp, Elizabeth

    2012-01-01

    Teaching qualitative research methods (QRM), particularly early on in one's academic career, can be challenging. This paper describes shared peer journaling as one way in which to cope with challenges such as complex debates in the field and student resistance to interpretive paradigms. Literature on teaching QRM and the pedagogical value of…

  11. External Influences on an Internal Process: Supporting Preservice Teacher Research

    Science.gov (United States)

    Schulte, Ann; Klipfel, Lyndsay Halpin

    2016-01-01

    In an effort to better understand how participating in teacher research as a student teacher compares to conducting it as a practicing teacher, a teacher educator and her former teacher education student engaged in a collaborative dialogue. They focus their reflections in this article on the impact of external forces on the process of teacher…

  12. Military Medical Research in Support of National Instruments of Power

    Science.gov (United States)

    2009-03-26

    diseases. Military sponsored research in the U.S. and abroad has produced antibiotic cures for typhoid and scrub typhus, new anti-malarial drugs, and...ARV drugs to Kenyan tea plantation workers has directly resulted in the reduction of absenteeism , maintenance of highly developed skill sets

  13. Institutional Support to Policy Research Organizations in India ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    It will do so through measures aimed at enhancing the ability of staff to conduct sound research, improving organizational performance and forging links with ... International Water Resources Association, in close collaboration with IDRC, is holding a webinar titled “Climate change and adaptive water management: ...

  14. TTI Phase 2 Institutional Support: Economic and Social Research ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    For ESRF, this project will help enhance its research quality, organizational performance, and policy engagement. ... -become more visible at the community and national levels through improved technology services, communications training, expanded reach of its community radio program, and proactive media relations ...

  15. Action Research to Support Teachers' Classroom Materials Development

    Science.gov (United States)

    Edwards, Emily; Burns, Anne

    2016-01-01

    Language teachers constantly create, adapt and evaluate classroom materials to develop new curricula and meet their learners' needs. It has long been argued (e.g. by Stenhouse, L. [1975]. "An Introduction to Curriculum Research and Development." London: Heinemann) that teachers themselves, as opposed to managers or course book writers,…

  16. IRIS: Supporting & Managing the Research Life-Cycle

    Science.gov (United States)

    Bollini, Andrea; Mennielli, Michele; Mornati, Susanna; Palmer, David T.

    2016-01-01

    IRIS is a new Current Research Information System (CRIS) developed by Cineca to upgrade and replace two previous solutions that have been used by Italian universities in the last 10 years. At the end of 2015, sixty-three Italian institutions are using IRIS. One of the main components of IRIS is DSpace-CRIS, an open source solution that can also be…

  17. Institutional Support : Institute for Research on Political Economy in ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    The Institut de recherche empirique en économie politique (IREEP) is an independent nonprofit organization established in 2004 with a view to contributing to the education of the next generation of teachers and researchers in political economy in Bénin and West Africa. IREEP has successfully integrated academic training ...

  18. Supporting relationships in reflexive movements in leadership and organisational research

    DEFF Research Database (Denmark)

    Mortensen, Ann Rubens

    , and the actions in these relationships have profound and long-lasting effects above and beyond the immediate context, i.e., the organisation. I am offering a systemic social constructionist perspective on reflexivity in leadership and organisational research, bringing forth a way of creating connections...

  19. As our earliest supported research projects move toward completion ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    CCAA

    and evaluation of farmer field schools” for southern and central ... CCAA research and capacity building projects, including papers, book chapters, newsletters, bulletins and theses .... climatique et à l'action de l'homme : mémoire de master de.

  20. Evidence-informed health policy 3 - interviews with the directors of organizations that support the use of research evidence.

    Science.gov (United States)

    Lavis, John N; Oxman, Andrew D; Moynihan, Ray; Paulsen, Elizabeth J

    2008-12-17

    Only a small number of previous efforts to describe the experiences of organizations that produce clinical practice guidelines (CPGs), undertake health technology assessments (HTAs), or directly support the use of research evidence in developing health policy (i.e., government support units, or GSUs) have relied on interviews and then only with HTA agencies. Interviews offer the potential for capturing experiences in great depth, particularly the experiences of organizations that may be under-represented in surveys. We purposively sampled organizations from among those who completed a questionnaire in the first phase of our three-phase study, developed and piloted a semi-structured interview guide, and conducted the interviews by telephone, audio-taped them, and took notes simultaneously. Binary or categorical responses to more structured questions were counted when possible. Themes were identified from among responses to semi-structured questions using a constant comparative method of analysis. Illustrative quotations were identified to supplement the narrative description of the themes. We interviewed the director (or his or her nominee) in 25 organizations, of which 12 were GSUs. Using rigorous methods that are systematic and transparent (sometimes shortened to 'being evidence-based') was the most commonly cited strength among all organizations. GSUs more consistently described their close links with policymakers as a strength, whereas organizations producing CPGs, HTAs, or both had conflicting viewpoints about such close links. With few exceptions, all types of organizations tended to focus largely on weaknesses in implementation, rather than strengths. The advice offered to those trying to establish similar organizations include: 1) collaborate with other organizations; 2) establish strong links with policymakers and stakeholders; 3) be independent and manage conflicts of interest; 4) build capacity; 5) use good methods and be transparent; 6) start small and

  1. Three-phase power load flow with uncertainty modeling via sinusoidal membership function; Fluxo de carga trifasico com modelagem de incertezas via funcao de pertinencia sinusoidal

    Energy Technology Data Exchange (ETDEWEB)

    Cavalcante, Patricia L.; Murari, Carlos Alberto F.; Salas, Silvio S. [Universidade Estadual de Campinas (UNICAMP), SP (Brazil). Fac. de Engenharia Eletrica e de Computacao], Emails: plc@dsee.fee.unicamp.br, murari@dsee.fee.unicamp.br, ssegura@dsee.fee.unicamp.br

    2009-07-01

    During the development of models for power systems, the researchers aim always to get results compatible with reality, and in this research it was our objective consider that some electric system variables are not deterministic, i e there is imprecision or variations, for example, on the loads. In this study, imprecise variables are represented as fuzzy numbers (the bell shape) and is presented a methodology for analysis of electrical networks of distribution through a specialist three-phase load flow that incorporates fuzzy sets and mathematical operations based on fuzzy logic. The results confirm the good performance of this new method.

  2. Transportation research activities in support of nuclear waste management programs

    International Nuclear Information System (INIS)

    Allen, G.C.; Luna, R.E.; Jefferson, R.M.; Wowak, W.E.

    1983-01-01

    The Transportation Technology Center has been conducting a wide range of technical and non-technical research activities to assure the ability to transport radioactive materials in a safe, reliable, and publicly acceptable manner. These activities include tasks in Information and Intergovernmental issues, Safety Assessment and Environmental Analysis and Technology Development. Until recently, the requirements of defense waste shipments have served as a focal point for development tasks with the expectation that they would serve as a precursor for commercial activities. The passage of the Nuclear Waste Policy Act has placed additional responsibility on DOE for concerns involving the shipments of civilian materials. The development of additional research responsibilities is expected to proceed concurrently with the evolution of the transportation mission plan for civilian spent fuel and high-level wastes

  3. Direction and Policies Needed to Support Hybrid Electric Car Research

    OpenAIRE

    Subekti, Ridwan Arief; Hartanto, Agus; Susanti, Vita

    2012-01-01

    The rising number of vehicles over the years has driven the increase of air pollution and fuel consumption. One of the solutions to overcome this problem is using hybrid electric car because it is environmentally friendly and efficient in fuel consumption. LIPI has conducted electric car research since 1997, but there were so many problems in its development that electric car can not be developed into a national industry scale. Therefore, it is important to conduct a study that maps the probl...

  4. Centralized supercomputer support for magnetic fusion energy research

    International Nuclear Information System (INIS)

    Fuss, D.; Tull, G.G.

    1984-01-01

    High-speed computers with large memories are vital to magnetic fusion energy research. Magnetohydrodynamic (MHD), transport, equilibrium, Vlasov, particle, and Fokker-Planck codes that model plasma behavior play an important role in designing experimental hardware and interpreting the resulting data, as well as in advancing plasma theory itself. The size, architecture, and software of supercomputers to run these codes are often the crucial constraints on the benefits such computational modeling can provide. Hence, vector computers such as the CRAY-1 offer a valuable research resource. To meet the computational needs of the fusion program, the National Magnetic Fusion Energy Computer Center (NMFECC) was established in 1974 at the Lawrence Livermore National Laboratory. Supercomputers at the central computing facility are linked to smaller computer centers at each of the major fusion laboratories by a satellite communication network. In addition to providing large-scale computing, the NMFECC environment stimulates collaboration and the sharing of computer codes and data among the many fusion researchers in a cost-effective manner

  5. European meteorological data: contribution to research, development, and policy support

    Science.gov (United States)

    Biavetti, Irene; Karetsos, Sotiris; Ceglar, Andrej; Toreti, Andrea; Panagos, Panos

    2014-08-01

    The Joint Research Centre of the European Commission has developed Interpolated Meteorological Datasets available on a regular 25x25km grid both to the scientific community and the general public. Among others, the Interpolated Meteorological Datasets include daily maximum/minimum temperature, cumulated daily precipitation, evapotranspiration and wind speed. These datasets can be accessed through a web interface after a simple registration procedure. The Interpolated Meteorological Datasets also serve the Crop Growth Monitoring System (CGMS) at European level. The temporal coverage of the datasets is more than 30 years and the spatial coverage includes EU Member States, neighboring European countries, and the Mediterranean countries. The meteorological data are highly relevant for the development, implementation and assessment of a number of European Union (EU) policy areas: agriculture, soil protection, environment, agriculture, food security, energy, climate change. An online user survey has been carried out in order to assess the impact of the Interpolated Meteorological Datasets on research developments. More than 70% of the users have used the meteorological datasets for research purposes and more than 50% of the users have used those sources as main input for their models. The usefulness of the data scored more than 70% and it is interesting to note that around 25% of the users have published their scientific outputs based on the Interpolated Meteorological Datasets. Finally, the user feedback focuses mostly on improving the data distribution process as well as the visibility of the web platform.

  6. Comparison of the quench and fault current limiting characteristics of the flux-coupling type SFCL with single and three-phase transformer

    International Nuclear Information System (INIS)

    Jung, Byung Ik; Cho, Yong Sun; Park, Hyoung Min; Chung, Dong Chul; Choi, Hyo Sang

    2013-01-01

    Highlight: ► Comparison of quench and fault-current-limiting behavior of SFCLs by Tr type. -- Abstract: The South Korean power grid has a network structure for the flexible operation of the system. The continuously increasing power demand necessitated the increase of power facilities, which decreased the impedance in the power system. As a result, the size of the fault current in the event of a system fault increased. As this increased fault current size is threatening the breaking capacity of the circuit breaker, the main protective device, a solution to this problem is needed. The superconducting fault current limiter (SFCL) has been designed to address this problem. SFCL supports the stable operation of the circuit breaker through its excellent fault-current-limiting operation [1–5]. In this paper, the quench and fault current limiting characteristics of the flux-coupling-type SFCL with one three-phase transformer were compared with those of the same SFCL type but with three single-phase transformers. In the case of the three-phase transformers, both the superconducting elements of the fault and sound phases were quenched, whereas in the case of the single-phase transformer, only that of the fault phase was quenched. For the fault current limiting rate, both cases showed similar rates for the single line-to-ground fault, but for the three-wire earth fault, the fault current limiting rate of the single-phase transformer was over 90% whereas that of the three-phase transformer was about 60%. It appears that when the three-phase transformer was used, the limiting rate decreased because the fluxes by the fault current of each phase were linked in one core. When the power loads of the superconducting elements were compared by fault type, the initial (half-cycle) load was great when the single-phase transformer was applied, whereas for the three-phase transformer, its power load was slightly lower at the initial stage but became greater after the half fault cycle

  7. Regulatory research and support program for 1988/89 - project descriptions

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1988-03-15

    Information Bulletin, 1988. Project descriptions for the Regulatory Research and Support Program. This Information Bulletin contains a list of the projects with a brief description of each, and additional supporting information.

  8. Regulatory research and support program for 1988/89 - project descriptions

    International Nuclear Information System (INIS)

    1988-01-01

    Information Bulletin, 1988. Project descriptions for the Regulatory Research and Support Program. This Information Bulletin contains a list of the projects with a brief description of each, and additional supporting information

  9. Coupled LBM-DEM Three-phase Simulation on Seepage of CO2 Stored under the Seabed.

    Science.gov (United States)

    Kano, Y.; Sato, T.

    2017-12-01

    Concerning the seepage of CO2 stored in a subsea formation, CO2 bubble/droplet rises to the sea-surface dissolving into the seawater, and the acidification of local seawater will be a problem. Previous research indicated that seepage rate and bubble size significantly affect its behaviour (Kano et al., 2009; Dewar et al., 2013). On the other hand, Kawada's experiments (2014) indicated that grain size affects formation of gas channels and bubbles through granular media. CO2 seepage through marine sediments probably shows similar behaviour. Additionally, such mobilisation and displacement of sand grains by gas migration may also cause capillary fracturing of CO2 in the reservoir and seal. To predict these phenomena, it is necessary to reveal three-phase behaviour of gas-water-sediment grains. We built gas-liquid-solid three-phase flow 3D simulator by coupling LBM-DEM program, and simulation results showed that the mobilisation of sand grain forms gas channels and affects bubble formation compared with that through solid porous media (Kano and Sato, 2017). In this presentation, we will report simulation results on effects of porosity, grain size and gas flow rate on the formation of gas channels and bubble and their comparison with laboratory experimental data. The results indicate that porosity and grain size of sand gravels affect the width of formed gas channels and resulting formed bubble size on the order of supposed seepage rate in the CO2 storage and that in most of experiment's conditions. References: Abe, S., Place, D., Mora, P., 2004. Pure. Appl. Geophys., 161, 2265-2277. (accessed Aug 01, 2017). Dewar, M., Wei, W., McNeil, D., Chen, B., 2013. Marine Pollution Bulletin 73(2), 504-515. Kano, Y., Sato, T., Kita, J., Hirabayashi, S., Tabeta, S., 2009. Int. J. Greenhouse Gas Control, Vol. 3(5), 617-625. Kano, Y. and Sato, T., 2017. In Proceeding of GHGT-13, Lausanne, Switzerland, Nov. 14-18, 2016. Kawada, R. 2014. Graduation thesis. Faculty of Engineering, The

  10. NETWORK-CENTRIC TECHNOLOGIES FOR CONTROL OF THREE-PHASE NETWORK OPERATION MODES

    Directory of Open Access Journals (Sweden)

    Ye. I. Sokol

    2017-06-01

    Full Text Available Purpose. The development of the control system for three-phase network is based on intelligent technologies of network-centric control of heterogeneous objects. The introduction of unmanned aerial vehicles for monitoring of three-phase network increases the efficiency of management. Methodology. The case of decomposition of the instantaneous capacities of the fixed and variable components for 3-wire system. The features of power balance for the different modes of its functioning. It should be noted that symmetric sinusoidal mode is balanced and good, but really unbalanced, if the standard reactive power is not zero. To solve the problem of compensation is sufficient knowledge of the total value of the inactive components of full power (value of the inactive power without detail. The creation of a methodology of measurement and assessment will require knowledge of the magnitudes of each inactive component separately, which leads to the development of a unified approach to the measurement and compensation of inactive components of full power and the development of a generalized theory of power. Results. Procedure for the compensation of the current of zero sequence excludes from circuit the source, as the active component of instantaneous power of zero sequence, and a vector due to a current of zero sequence. This procedure is performed without time delay as it does not require integration. Only a 3–wire system with symmetrical voltage eliminates pulsations and symmetrization of the equivalent conductances of the phases of the task. Under asymmetric voltage, the power is different, its analysis requires the creation of a vector mathematical model of the energy processes of asymmetrical modes of 3–phase systems. Originality. The proposed method extends the basis of the vector method for any zero sequence voltages and shows that the various theories of instantaneous power three wired scheme due to the choice of a basis in a two

  11. Wavelet-fuzzy speed indirect field oriented controller for three-phase AC motor drive – Investigation and implementation

    Directory of Open Access Journals (Sweden)

    Sanjeevikumar Padmanaban

    2016-09-01

    Full Text Available Three-phase voltage source inverter driven induction motor is used in many medium- and high-power applications. Precision in speed of the motor play vital role, i.e. popular methods of direct/indirect field-oriented control (FOC are applied. FOC is employed with proportional–integral (P-I or proportional–integral–derivative (P-I-D controllers and they are not adaptive, since gains are fixed at all operating conditions. Therefore, it needs a robust speed controlling in precision for induction motor drive application. This research paper articulates a novel speed control for FOC induction motor drive based on wavelet-fuzzy logic interface system. In specific, the P-I-D controller of IFOC which is actually replaced by the wavelet-fuzzy controller. The speed feedback (error signal is composed of multiple low and high frequency components. Further, these components are decomposed by the discrete wavelet transform and the fuzzy logic controller to generate the scaled gains for the indirect FOC induction motor. Complete model of the proposed ac motor drive is developed with numerical simulation Matlab/Simulink software and tested under different working conditions. For experimental verification, a hardware prototype was implemented and the control algorithm is framed using TMS320F2812 digital signal processor (dsp. Both simulation and hardware results presented in this paper are shown in close agreement and conformity about the suitability for industrial applications.

  12. Arctic Glass: Innovative Consumer Technology in Support of Arctic Research

    Science.gov (United States)

    Ruthkoski, T.

    2015-12-01

    The advancement of cyberinfrastructure on the North Slope of Alaska is drastically limited by location-specific conditions, including: unique geophysical features, remoteness of location, and harsh climate. The associated cost of maintaining this unique cyberinfrastructure also becomes a limiting factor. As a result, field experiments conducted in this region have historically been at a technological disadvantage. The Arctic Glass project explored a variety of scenarios where innovative consumer-grade technology was leveraged as a lightweight, rapidly deployable, sustainable, alternatives to traditional large-scale Arctic cyberinfrastructure installations. Google Glass, cloud computing services, Internet of Things (IoT) microcontrollers, miniature LIDAR, co2 sensors designed for HVAC systems, and portable network kits are several of the components field-tested at the Toolik Field Station as part of this project. Region-specific software was also developed, including a multi featured, voice controlled Google Glass application named "Arctic Glass". Additionally, real-time sensor monitoring and remote control capability was evaluated through the deployment of a small cluster of microcontroller devices. Network robustness was analyzed as the devices delivered streams of abiotic data to a web-based dashboard monitoring service in near real time. The same data was also uploaded synchronously by the devices to Amazon Web Services. A detailed overview of solutions deployed during the 2015 field season, results from experiments utilizing consumer sensors, and potential roles consumer technology could play in support of Arctic science will be discussed.

  13. Low sensitivity of three-phase bone scintigraphy for the diagnosis of repetitive strain injury

    Directory of Open Access Journals (Sweden)

    Bárbara Juarez Amorim

    Full Text Available CONTEXT AND OBJECTIVE: The diagnosis of repetitive strain injury (RSI is subjective and solely based on clinical signs and physical examination. The aim of this paper was to assess the usefulness of three-phase bone scintigraphy (TPBS in diagnosing RSI. DESIGN AND SETTING: Prospective study at the Division of Nuclear Medicine, Department of Radiology, School of Medical Sciences, Universidade Estadual de Campinas (Unicamp. METHODS: Seventy-three patients (mean age 31.2 years; 47 males with clinical suspicion of RSI in the upper limbs were studied. A total of 127 joints with suspicion of RSI were studied. The shoulders, elbows and wrists were analyzed semi-quantitatively, using the shafts of the humeri and ulnae as references. The results were compared with a control group of 40 normal individuals. The patients’ signs and symptoms were used as the "gold standard" for calculating the probabilities. RESULTS: From visual analysis, abnormalities were observed in the flow phase for four joints, in the blood pool phase for 11 joints and in the delayed images for 26 joints. Visual analysis of the joints of the control group did not show any abnormalities. Semi-quantitative analysis showed that most of the patients’ joint ratios were normal. The exceptions were the wrists of patients with left-sided RSI (p = 0.0216. However, the sensitivity (9% and accuracy (41% were very low. CONCLUSION: TPBS with semi-quantitative analysis has very low sensitivity and accuracy in the detection of RSI abnormalities in the upper limbs.

  14. Three phase heat and mass transfer model for unsaturated soil freezing process: Part 1 - model development

    Science.gov (United States)

    Xu, Fei; Zhang, Yaning; Jin, Guangri; Li, Bingxi; Kim, Yong-Song; Xie, Gongnan; Fu, Zhongbin

    2018-04-01

    A three-phase model capable of predicting the heat transfer and moisture migration for soil freezing process was developed based on the Shen-Chen model and the mechanisms of heat and mass transfer in unsaturated soil freezing. The pre-melted film was taken into consideration, and the relationship between film thickness and soil temperature was used to calculate the liquid water fraction in both frozen zone and freezing fringe. The force that causes the moisture migration was calculated by the sum of several interactive forces and the suction in the pre-melted film was regarded as an interactive force between ice and water. Two kinds of resistance were regarded as a kind of body force related to the water films between the ice grains and soil grains, and a block force instead of gravity was introduced to keep balance with gravity before soil freezing. Lattice Boltzmann method was used in the simulation, and the input variables for the simulation included the size of computational domain, obstacle fraction, liquid water fraction, air fraction and soil porosity. The model is capable of predicting the water content distribution along soil depth and variations in water content and temperature during soil freezing process.

  15. Modular Plug’n’Play Control Architectures for Three-phase Inverters in UPS Applications

    DEFF Research Database (Denmark)

    Zhang, Chi; Guerrero, Josep M.; Vasquez, Juan Carlos

    2015-01-01

    In this paper a control strategy for the parallel operation of three-phase inverters in a modular online uninterruptable power supply (UPS) system is proposed. The UPS system is composed of a number for DC/ACs with LC filter connected to the same AC critical bus and an AC/DC that forms the DC bus...... the AC critical bus voltage. Detailed control architecture, regarding individual layer and recovery layer, are presented in this paper. Also an experimental setup was built to validate the proposed control approach under several scenarios-case study........ The proposed control is designated in two layers, individual layer and recovery layer. In individual layer, virtual impedance concept is employed in order to achieve active power sharing while individual reactive power is calculated to modify output voltage phases to achieve reactive power sharing among...... different modules. Recovery layer is mainly responsible for guaranteeing synchronization capability with the utility and voltage recovery. With the proposed control, improved voltage transient performance can be achieved and also DC/AC modules are allowed to be plugged in and out flexibly while controlling...

  16. Biocatalytic methanation of hydrogen and carbon dioxide in an anaerobic three-phase system.

    Science.gov (United States)

    Burkhardt, M; Koschack, T; Busch, G

    2015-02-01

    A new type of anaerobic trickle-bed reactor was used for biocatalytic methanation of hydrogen and carbon dioxide under mesophilic temperatures and ambient pressure in a continuous process. The conversion of gaseous substrates through immobilized hydrogenotrophic methanogenic archaea in a biofilm is a unique feature of this type of reactor. Due to the formation of a three-phase system on the carrier surface and operation as a plug flow reactor without gas recirculation, a complete reaction could be observed. With a methane concentration higher than c(CH4) = 98%, the product gas exhibits a very high quality. A specific methane production of P(CH4) = 1.49 Nm(3)/(m(3)(SV) d) was achieved at a hydraulic loading rate of LR(H2) = 6.0 Nm(3)/(m(3)(SV) d). The relation between trickle flow through the reactor and productivity could be shown. An application for methane enrichment in combination with biogas facilities as a source of carbon dioxide has also been positively proven. Copyright © 2014 Elsevier Ltd. All rights reserved.

  17. Three-Phase PV CHB Inverter for a Distributed Power Generation System

    Directory of Open Access Journals (Sweden)

    Pierluigi Guerriero

    2016-10-01

    Full Text Available This work deals with the design of a three-phase grid-tied photovoltaic (PV cascade H-bridge inverter for distributed power conversion. The power balancing among the phases must be properly addressed. In fact, an intra-phase power imbalance—arising from uneven irradiance and temperature conditions—generates a per-phase power imbalance. This latter can be compensated by the injection of a proper zero-sequence voltage, while the intra-phase balance is ensured by means of a hybrid modulation method which is able to guarantee the handling of unequal DC (Direct Current sources, stable circuit operation, and maximization of PV power production. The digital controller is developed and tested in Matlab/Simulink environment integrated with XSG (Xilinx System Generator, thus allowing an easy transfer on a field-programmable gate array (FPGA platform and accurately describing the behavior of a real hardware implementation. Thus, numerical results have been considered to prove the effectiveness of the proposed approach.

  18. A multidisciplinary three-phase approach to improve the clinical utility of patient safety indicators.

    Science.gov (United States)

    Najjar, Peter; Kachalia, Allen; Sutherland, Tori; Beloff, Jennifer; David-Kasdan, Jo Ann; Bates, David W; Urman, Richard D

    2015-01-01

    The AHRQ Patient Safety Indicators (PSIs) are used for calculation of risk-adjusted postoperative rates for adverse events. The payers and quality consortiums are increasingly requiring public reporting of hospital performance on these metrics. We discuss processes designed to improve the accuracy and clinical utility of PSI reporting in practice. The study was conducted at a 793-bed tertiary care academic medical center where PSI processes have been aggressively implemented to track patient safety events at discharge. A three-phased approach to improving administrative data quality was implemented. The initiative consisted of clinical review of all PSIs, documentation improvement, and provider outreach including active querying for patient safety events. This multidisciplinary effort to develop a streamlined process for PSI calculation reduced the reporting of miscoded PSIs and increased the clinical utility of PSI monitoring. Over 4 quarters, 4 of 41 (10%) PSI-11 and 9 of 138 (7%) PSI-15 errors were identified on review of clinical documentation and appropriate adjustments were made. A multidisciplinary, phased approach leveraging existing billing infrastructure for robust metric coding, ongoing clinical review, and frontline provider outreach is a novel and effective way to reduce the reporting of false-positive outcomes and improve the clinical utility of PSIs.

  19. From Two-Phase to Three-Phase: The New Electrochemical Interface by Oxide Electrocatalysts

    Science.gov (United States)

    Xu, Zhichuan J.

    2018-03-01

    Electrochemical reactions typically occur at the interface between a solid electrode and a liquid electrolyte. The charge exchange behaviour between these two phases determines the kinetics of electrochemical reactions. In the past few years, significant advances have been made in the development of metal oxide electrocatalysts for fuel cell and electrolyser reactions. However, considerable gaps remain in the fundamental understanding of the charge transfer pathways and the interaction between the metal oxides and the conducting substrate on which they are located. In particular, the electrochemical interfaces of metal oxides are significantly different from the traditional (metal) ones, where only a conductive solid electrode and a liquid electrolyte are considered. Oxides are insulating and have to be combined with carbon as a conductive mediator. This electrode configuration results in a three-phase electrochemical interface, consisting of the insulating oxide, the conductive carbon, and the liquid electrolyte. To date, the mechanistic insights into this kind of non-traditional electrochemical interface remain unclear. Consequently conventional electrochemistry concepts, established on classical electrode materials and their two-phase interfaces, are facing challenges when employed for explaining these new electrode materials. [Figure not available: see fulltext.

  20. Phenolic Wastewater Treatment using Activated Carbon in a Three Phase Fluidized-Bed Reactor

    Directory of Open Access Journals (Sweden)

    Pornsiri Tongprem

    2009-11-01

    Full Text Available Phenolic wastewater treatment was investigated using activated carbon in a lab scale three phase fluidized-bed reactor. The reactor with effective volume of 272 ml, 300 mm in height and 40 mm in diameter was made from transparent acrylic that allowed to observe the phenomena occurring inside. Phenol 10 mg/l and air were used as representative agents that were continuously fed to the reactor at a constant flow rate of 1 and 2 l/min with co-current and up-flow, respectively. Comparison of the phenolic adsorption under five different conditions: (a fresh Acs, (b 1st reused Acs, (c fresh Fe/Acs, (d 1st reused Fe/Acs, and (e 2nd reused Fe/Acs, have been carried out. The phenolic wastewater was re-circulated through the reactor and its concentration was measured with respect to time. The experimental adsorption results revealed that both fresh Acs and Fe/Acs gave the better results than reused Acs and reused Fe/Acs, respectively. The adsorption in all cases of Acs and Fe/Acs would follow Pseudo-second order kinetic.

  1. An alternative approach in operator allocation labor intensive manufacturing system: A three-phase methodology framework

    Science.gov (United States)

    Mat Rani, Ruzanita; Ismail, Wan Rosmanira

    2013-04-01

    Operator allocation is one of the most important decisions that can affect productivity in labor-intensive manufacturing system. Improper decision on operator allocation will reduce company's throughput and increase waste. Therefore, all factors such as operators' performance and operational constraints need to be considered in making the best operator allocation decision. Most of previous studies used two phases methodology. In two phases methodology, they used operational constraints and treated all operators to have the same level of performance for making decision on operator allocation. Therefore, in this paper a three-phase methodology is proposed to determine the optimal operator allocation. This methodology advances the existing approach on operator allocation by combining operators' performance and operational constraints. The methodology starts with evaluating the operators' performance. Then, it is followed with determining inputs and outputs for operator allocation alternatives and it ends with determining the optimal operator allocation. This paper will give ideas and directions to the management of the manufacturing company in determining the optimal operator allocation decision.

  2. Droplets and the three-phase contact line at the nano-scale. Statics and dynamics

    Science.gov (United States)

    Yatsyshin, Petr; Sibley, David; Savva, Nikos; Kalliadasis, Serafim

    2014-11-01

    Understanding the behaviour of the solid-liquid-vapour contact line at the scale of several tens of molecular diameters is important in wetting hydrodynamics with applications in micro- and nano-fluidics, including the design of lab-on-a-chip devices and surfaces with specific wetting properties. Due to the fluid inhomogeneity at the nano-scale, the application of continuum-mechanical approaches is limited, and a natural way to remedy this is to seek descriptions accounting for the non-local molecular-level interactions. Density Functional Theory (DFT) for fluids offers a statistical-mechanical framework based on expressing the free energy of the fluid-solid pair as a functional of the spatially varying fluid density. DFT allows us to investigate small drops deposited on planar substrates whilst keeping track of the microscopic structural details of the fluid. Starting from a model of intermolecular forces, we systematically obtain interfaces, surface tensions, and the microscopic contact angle. Using a dynamic extension of equilibrium DFT, we investigate the diffusion-driven evolution of the three-phase contact line to gain insight into the dynamic behaviour of the microscopic contact angle, which is still under debate.

  3. Vibration mode and vibration shape under excitation of a three phase model transformer core

    Science.gov (United States)

    Okabe, Seiji; Ishigaki, Yusuke; Omura, Takeshi

    2018-04-01

    Structural vibration characteristics and vibration shapes under three-phase excitation of a archetype transformer core were investigated to consider their influences on transformer noise. Acoustic noise and vibration behavior were measured in a three-limb model transformer core. Experimental modal analysis by impact test was performed. The vibration shapes were measured by a laser scanning vibrometer at different exciting frequencies. Vibration amplitude of the core in out-of-plane direction were relatively larger than those in other two in-plane directions. It was consistent with the result that the frequency response function of the core in out-of-plane direction was larger by about 20 dB or more than those in in-plane directions. There were many vibration modes having bending deformation of limbs in out-of-plane direction. The vibration shapes of the core when excited at 50 Hz and 60 Hz were almost the same because the fundamental frequencies of the vibration were not close to the resonance frequencies. When excitation frequency was 69 Hz which was half of one of the resonance frequencies, the vibration shape changed to the one similar to the resonance vibration mode. Existence of many vibration modes in out-of-plane direction of the core was presumed to be a reason why frequency characteristics of magnetostriction and transformer noise do not coincide.

  4. Advances on the time differential three-phase-lag heat conduction model and major open issues

    Science.gov (United States)

    D'Apice, Ciro; Zampoli, Vittorio

    2017-07-01

    The main purpose of this short contribution is to summarize the recent achievements concerning the so-called time differential three-phase-lag heat conduction model, contextually focusing attention on some of the numerous open problems associated with such an attractive theory. After having briefly recalled the origin of the model at issue, the restrictions upon the delay times and the constitutive tensors able to make it thermodynamically consistent are recalled. Under these hypotheses, the investigation of the well-posedness issue has already provided important results in terms of uniqueness and continuous dependence of the solutions (even related to the thermoelastic case), as well as in terms of existence of a domain of influence of the assigned data in connection with the thermoelastic model. Finally, some of the main problems currently object of investigation are recalled, including the very challenging issues about the different possible choices of Taylor series expansion orders for the constitutive equation, the interaction of the model with energy processes that take place on the nanoscale, with multi-porous materials and with biological systems.

  5. Analysis of dc-Link Voltage Switching Ripple in Three-Phase PWM Inverters

    Directory of Open Access Journals (Sweden)

    Marija Vujacic

    2018-02-01

    Full Text Available The three-phase voltage source inverter (VSI is de facto standard in power conversion systems. To realize high power density systems, one of the items to be correctly addressed is the design and selection of the dc-link capacitor in relation to the voltage switching ripple. In this paper, effective formulas for designing the dc-link capacitor as a function of the switching voltage ripple amplitude are obtained, considering the operating conditions such as the modulation index and the output current amplitude. The calculations are obtained considering the requirements and restrictions referring to the high (switching-frequency dc-link voltage ripple component. Analyses have been performed considering the dc source impedance (non-ideal dc voltage source at the switching frequency and a balanced load. Analytical expressions are derived for the dc-link voltage switching ripple amplitude and its maximum value over the fundamental period. Different values of modulation index and output phase angle have been considered and different diagrams are presented. Analytical results were validated both by simulations and comprehensive experimental tests.

  6. A Smart Voltage and Current Monitoring System for Three Phase Inverters Using an Android Smartphone Application.

    Science.gov (United States)

    Mnati, Mohannad Jabbar; Van den Bossche, Alex; Chisab, Raad Farhood

    2017-04-15

    In this paper, a new smart voltage and current monitoring system (SVCMS) technique is proposed. It monitors a three phase electrical system using an Arduino platform as a microcontroller to read the voltage and current from sensors and then wirelessly send the measured data to monitor the results using a new Android application. The integrated SVCMS design uses an Arduino Nano V3.0 as the microcontroller to measure the results from three voltage and three current sensors and then send this data, after calculation, to the Android smartphone device of an end user using Bluetooth HC-05. The Arduino Nano V3.0 controller and Bluetooth HC-05 are a cheap microcontroller and wireless device, respectively. The new Android smartphone application that monitors the voltage and current measurements uses the open source MIT App Inventor 2 software. It allows for monitoring some elementary fundamental voltage power quality properties. An effort has been made to investigate what is possible using available off-the-shelf components and open source software.

  7. Three-Phase Carbon Fiber Amine Functionalized Carbon Nanotubes Epoxy Composite: Processing, Characterisation, and Multiscale Modeling

    Directory of Open Access Journals (Sweden)

    Kamal Sharma

    2014-01-01

    Full Text Available The present paper discusses the key issues of carbon nanotube (CNT dispersion and effect of functionalisation on the mechanical properties of multiscale carbon epoxy composites. In this study, CNTs were added in epoxy matrix and further reinforced with carbon fibres. Predetermined amounts of optimally amine functionalised CNTs were dispersed in epoxy matrix, and unidirectional carbon fiber laminates were produced. The effect of the presence of CNTs (1.0 wt% in the resin was reflected by pronounced increase in Young’s modulus, inter-laminar shear strength, and flexural modulus by 51.46%, 39.62%, and 38.04%, respectively. However, 1.5 wt% CNT loading in epoxy resin decreased the overall properties of the three-phase composites. A combination of Halpin-Tsai equations and micromechanics modeling approach was also used to evaluate the mechanical properties of multiscale composites and the differences between the predicted and experimental values are reported. These multiscale composites are likely to be used for potential missile and aerospace structural applications.

  8. Indium-111-chloride and three-phase bone scintigraphy: A comparison for imaging experimental osteomyelitis

    International Nuclear Information System (INIS)

    Hoskinson, J.J.; Daniel, G.B.; Patton, C.S.

    1991-01-01

    To investigate the utility of indium-111-chloride ( 111 In-Cl) imaging in detecting osteomyelitis complicating surgical or fracture sites, the proximal tibia of 11 dogs were experimentally infected with Staphylococcus aureus after creation of a cortical defect. The contralateral limb served as a sham-operated control. Animals were serially imaged by radiography, three-phase technetium-99m-methylene diphosphonate (99mTc-MDP) scintigraphy, and 111 In-Cl scintigraphy. There was a significant difference between infected (1.93) and noninfected (1.32) limb's tibia/femur count density ratios on 24-hr (p = 0.0001) and 72-hr (p = 0.0001) 111 In-Cl images. A smaller difference was found for 99mTc-MDP bone-phase tibia/femur ratios (p = 0.0199). Using receiver operator characteristic analysis of tibia/femur ratios, a sensitivity of 61%, specificity of 88%, and positive (75%) and negative (79%) predictive values were determined for the 24-hr 111 In-Cl images. Indium-111-chloride was superior to 99mTc-MDP in differentiating infected and noninfected operative sites

  9. Discovery of fossil lamprey larva from the Lower Cretaceous reveals its three-phased life cycle.

    Science.gov (United States)

    Chang, Mee-mann; Wu, Feixiang; Miao, Desui; Zhang, Jiangyong

    2014-10-28

    Lampreys are one of the two surviving jawless vertebrate groups and one of a few vertebrate groups with the best exemplified metamorphosis during their life cycle, which consists of a long-lasting larval stage, a peculiar metamorphosis, and a relatively short adulthood with a markedly different anatomy. Although the fossil records have revealed that many general features of extant lamprey adults were already formed by the Late Devonian (ca. 360 Ma), little is known about the life cycle of the fossil lampreys because of the lack of fossilized lamprey larvae or transformers. Here we report the first to our knowledge discovery of exceptionally preserved premetamorphic and metamorphosing larvae of the fossil lamprey Mesomyzon mengae from the Lower Cretaceous of Inner Mongolia, China. These fossil ammocoetes look surprisingly modern in having an eel-like body with tiny eyes, oral hood and lower lip, anteriorly positioned branchial region, and a continuous dorsal skin fin fold and in sharing a similar feeding habit, as judged from the detritus left in the gut. In contrast, the larger metamorphosing individuals have slightly enlarged eyes relative to large otic capsules, thickened oral hood or pointed snout, and discernable radials but still anteriorly extended branchial area and lack a suctorial oral disk, which characterize the early stages of the metamorphosis of extant lampreys. Our discovery not only documents the larval conditions of fossil lampreys but also indicates the three-phased life cycle in lampreys emerged essentially in their present mode no later than the Early Cretaceous.

  10. Modeling of a three-phase reactor for bitumen-derived gas oil hydrotreating

    Energy Technology Data Exchange (ETDEWEB)

    Chacon, R.; Canale, A.; Bouza, A. [Departamento de Termodinamica y Fenomenos de Transporte. Universidad Simon Bolivar, Caracas (Venezuela, Bolivarian Republic of); Sanchez, Y. [Departamento de Procesos y Sistemas. Universidad Simon Bolivar (Venezuela, Bolivarian Republic of)

    2012-01-15

    A three-phase reactor model for describing the hydrotreating reactions of bitumen-derived gas oil was developed. The model incorporates the mass-transfer resistance at the gas-liquid and liquid-solid interfaces and a kinetic rate expression based on a Langmuir-Hinshelwood-type model. We derived three correlations for determining the solubility of hydrogen (H{sub 2}), hydrogen sulfide (H{sub 2}S) and ammonia (NH{sub 3}) in hydrocarbon mixtures and the calculation of the catalyst effectiveness factor was included. Experimental data taken from the literature were used to determine the kinetic parameters (stoichiometric coefficients, reaction orders, reaction rate and adsorption constants for hydrodesulfuration (HDS) and hydrodenitrogenation (HDN)) and to validate the model under various operating conditions. Finally, we studied the effect of operating conditions such as pressure, temperature, LHSV, H{sub 2}/feed ratio and the inhibiting effect of H{sub 2}S on HDS and NH{sub 3} on HDN. (author)

  11. Traffic breakdown at a signal: classical theory versus the three-phase theory of city traffic

    International Nuclear Information System (INIS)

    Kerner, Boris S; Schreckenberg, Michael; Klenov, Sergey L

    2014-01-01

    Physical reasons for a crucial difference between the results of a three-phase theory developed recently (Kerner 2011 Phys. Rev. E 84 045102(R); 2013 Europhys. Lett. 102 28010; 2014 Physica A 397 76) and the classical theory are explained. Microscopic characteristics of traffic passing a traffic signal during the green signal phase and their dependence on the duration of the green phase have been found. It turns out that a moving synchronized flow pattern (MSP), which occurs in under-saturated traffic at the signal, causes ‘compression’ of traffic flow: the rate of MSP discharge can be considerably larger than the saturation flow rate of the classical traffic theory of city traffic. This leads to a considerably larger rate of traffic passing the signal in comparison with the saturation flow rate. This effect together with traffic behavior at the upstream queue front explains the metastability of under-saturated traffic with respect to a random time-delayed traffic breakdown. (paper)

  12. Comparative study of researcher community support and supervisory support among Finnish and Danish PhD-students

    DEFF Research Database (Denmark)

    Cornér, Solveig; Pyhältö, Kirsi; Peltonen, Jouni

    Prior research on doctoral supervision and researcher communities has identified social support as a key determinant of the doctoral journey (Jairam & Kahl, 2012; Zhao, Golde & McCormick, 2007). Supervisory support, for instance, in terms of constructive feedback and encouragement (Pyhältö......, 313-329. • Pyhältö, K., Vekkaila (o.s. Tuomainen), J., & Keskinen, J. (2015). Fit matters in the supervisory relationship: Doctoral students’ and supervisors’ perceptions about supervisory activities. Innovations in Education and Teaching International, 52(1), 4-16. • Zhau, C-M, Golde, C.M., McCormick...

  13. The Geosciences Division of the Council on Undergraduate Research (GeoCUR): Supporting Faculty that Mentor Undergraduate Researchers

    Science.gov (United States)

    Fox, L. K.; Guertin, L. A.; Manley, P. L.; Fortner, S. K.

    2012-12-01

    Undergraduate research is a proven effective pedagogy that has a number of benefits including: enhancing student learning through mentoring relationships with faculty; increasing retention; increasing enrollment in graduate programs; developing critical thinking, creativity, problem solving and intellectual independence; and, developing an understanding of research methodology. Undergraduate research also has been demonstrated in preparing students for careers. In addition to developing disciplinary and technical expertise, participation in undergraduate research helps students improve communication skills (written, oral, and graphical) and time management. Early involvement in undergraduate research improves retention and, for those engaged at the 2YC level, helps students successfully transfers to 4YC. The Geosciences Division of the Council on Undergraduate Research (GeoCUR) supports faculty in their development of undergraduate research programs at all levels. GeoCUR leads workshops for new and future faculty covering all aspects of undergraduate research including incorporating research into coursework, project design, mentoring students, sustaining programs, and funding sources. GeoCUR members support new faculty by providing a range of services including: peer-review of grant proposals; advice on establishing an undergraduate research program; balancing teaching and research demands; and networking with other geoscientist. GeoCUR has also developed web resources that support faculty and departments in development of undergraduate research programs (http://serc.carleton.edu/NAGTWorkshops/undergraduate_research/index.html). This presentation will describe the services provided by GeoCUR and highlight examples of programs and resources available to geoscientists in all career stages for effective undergraduate research mentoring and development.

  14. NASA supporting studies for microgravity research on eye movements

    Science.gov (United States)

    Cohen, Bernard

    1990-01-01

    The purpose of the work on this project was to provide support for ground-based studies on the effects of gravity on eye movements. The effects of microgravity on the optokinetic eye movements of humans are investigated. OKN was induced by having subjects watch 3.3 deg stripes moving at 35 deg/s for 45 s in a binocular, head-fixed apparatus. The field (hor., 88 deg; vert., 72 deg), was rotated about axes that were upright or tilted 45 deg or 90 deg. The head was upright or tilted 45 deg on the body. Head-horizontal (yaw axis) and head-vertical (pitch axis) components of OKN were recorded with electro-oculography (EOG). Slow phase velocity vectors were determined relative to gravity. With the head upright, the axis of eye rotation during yaw axis OKN was coincident with the stimulus axis and the spatial vertical. With the head tilted 45 deg on the body, a persistent vertical component of eye velocity developed during yaw axis stimulation, and there was an average shift of the axis of eye rotation toward the spatial vertical of approximately 18 deg in six subjects. During oblique optokinetic stimulation with the head upright, the axis of eye rotation shifted 12 deg toward the spatial vertical. When the head was tilted, the axis of eye rotation rotated to the other side of the spatial vertical by 5.4 deg during the same oblique stimulation. This counter-rotation of the axis of eye rotation is similar to the 'Muller (E) effect', in which the perception of the upright counter-rotates to the opposite side of the spatial vertical when subjects are tilted in darkness. The data were simulated by a model of OKN. Despite the short OKAN time constants, strong horizontal to vertical cross-coupling was produced if the horizontal and vertical time constants were in proper ratio, and there was no suppression of nystagmus orthogonal to the stimulus direction. This shows that the spatial orientation of OKN can be due to a restructuring of the system matrix of velocity storage as a

  15. Fostering integrity in postgraduate research: an evidence-based policy and support framework.

    Science.gov (United States)

    Mahmud, Saadia; Bretag, Tracey

    2014-01-01

    Postgraduate research students have a unique position in the debate on integrity in research as students and novice researchers. To assess how far policies for integrity in postgraduate research meet the needs of students as "research trainees," we reviewed online policies for integrity in postgraduate research at nine particular Australian universities against the Australian Code for Responsible Conduct of Research (the Code) and the five core elements of exemplary academic integrity policy identified by Bretag et al. (2011 ), i.e., access, approach, responsibility, detail, and support. We found inconsistency with the Code in the definition of research misconduct and a lack of adequate detail and support. Based on our analysis, previous research, and the literature, we propose a framework for policy and support for postgraduate research that encompasses a consistent and educative approach to integrity maintained across the university at all levels of scholarship and for all stakeholders.

  16. Geophysical Observations Supporting Research of Magmatic Processes at Icelandic Volcanoes

    Science.gov (United States)

    Vogfjörd, Kristín. S.; Hjaltadóttir, Sigurlaug; Roberts, Matthew J.

    2010-05-01

    Magmatic processes at volcanoes on the boundary between the European and North American plates in Iceland are observed with in-situ multidisciplinary geophysical networks owned by different national, European or American universities and research institutions, but through collaboration mostly operated by the Icelandic Meteorological Office. The terrestrial observations are augmented by space-based interferometric synthetic aperture radar (InSAR) images of the volcanoes and their surrounding surface. Together this infrastructure can monitor magma movements in several volcanoes from the base of the crust up to the surface. The national seismic network is sensitive enough to detect small scale seismicity deep in the crust under some of the voclanoes. High resolution mapping of this seismicity and its temporal progression has been used to delineate the track of the magma as it migrates upwards in the crust, either to form an intrusion at shallow levels or to reach the surface in an eruption. Broadband recording has also enabled capturing low frequency signals emanating from magmatic movements. In two volcanoes, Eyjafjallajökull and Katla, just east of the South Iceland Seismic Zone (SISZ), seismicity just above the crust-mantle boundary has revealed magma intruding into the crust from the mantle below. As the magma moves to shallower levels, the deformation of the Earth‘s surface is captured by geodetic systems, such as continuous GPS networks, (InSAR) images of the surface and -- even more sensitive to the deformation -- strain meters placed in boreholes around 200 m below the Earth‘s surface. Analysis of these signals can reveal the size and shape of the magma as well as the temporal evolution. At near-by Hekla volcano flanking the SISZ to the north, where only 50% of events are of M>1 compared to 86% of earthquakes in Eyjafjallajökull, the sensitivity of the seismic network is insufficient to detect the smallest seismicity and so the volcano appears less

  17. United States Domestic Research Reactor Infrastructure - TRIGA Reactor Fuel Support

    International Nuclear Information System (INIS)

    Morrell, Douglas

    2008-01-01

    The purpose of the United State Domestic Research Reactor Infrastructure Program is to provide fresh nuclear reactor fuel to United States universities at no, or low, cost to the university. The title of the fuel remains with the United States government and when universities are finished with the fuel, the fuel is returned to the United States government. The program is funded by the United States Department of Energy - Nuclear Energy division, managed by Department of Energy - Idaho Field Office, and contracted to the Idaho National Laboratory's Management and Operations Contractor - Battelle Energy Alliance. Program has been at Idaho since 1977 and INL subcontracts with 26 United States domestic reactor facilities (13 TRIGA facilities, 9 plate fuel facilities, 2 AGN facilities, 1 Pulstar fuel facility, 1 Critical facility). University has not shipped fuel since 1968 and as such, we have no present procedures for shipping spent fuel. In addition: floor loading rate is unknown, many interferences must be removed to allow direct access to the reactor tank, floor space in the reactor cell is very limited, pavement ends inside our fence; some of the surface is not finished. The whole approach is narrow, curving and downhill. A truck large enough to transport the cask cannot pull into the lot and then back out (nearly impossible / refused by drivers); a large capacity (100 ton), long boom crane would have to be used due to loading dock obstructions. Access to the entrance door is on a sidewalk. The campus uses it as a road for construction equipment, deliveries and security response. Large trees are on both sides of sidewalk. Spent fuel shipments have never been done, no procedures approved or in place, no approved casks, no accident or safety analysis for spent fuel loading. Any cask assembly used in this facility will have to be removed from one crane, moved on the floor and then attached to another crane to get from the staging area to the reactor room. Reactor

  18. Research on Social Networking Sites and Social Support from 2004 to 2015: A Narrative Review and Directions for Future Research.

    Science.gov (United States)

    Meng, Jingbo; Martinez, Lourdes; Holmstrom, Amanda; Chung, Minwoong; Cox, Jeff

    2017-01-01

    The article presents a narrative review of scholarship on social support through social networking sites (SNSs) published from 2004 to 2015. By searching keywords related to social support and SNSs in major databases for social sciences, we identified and content analyzed directly relevant articles (N = 88). The article summarizes the prevalence of theory usage; the function of theory usage (e.g., testing a theory, developing a theory); major theories referenced; and methodologies, including research designs, measurement, and the roles of social support and SNS examined in this literature. It also reports four themes identified across the studies, indicating the trends in the current research. Based on the review, the article presents a discussion about study sites, conceptualization of social support, theoretical coherence, the role of social networks, and the dynamic relationships between SNS use and social support, which points out potential avenues for shaping a future research agenda.

  19. Development of a synchronous key to controlled energization of three-phase transformers; Desenvolvimento de uma chave sincrona para energizacao controlada de transformadores trifasicos

    Energy Technology Data Exchange (ETDEWEB)

    Araujo, Leandro de Luna; Freire, Selma Cristina de Freitas [Universidade Federal de Campina Grande (COPELE/UFCG), PB (Brazil). Coordenacao de Pos Graduacao em Engenharia Eletrica], Emails: leandrolun@gmail.com, selma.freire@ee.ufcg.edu.br; Guerra, Francisco das Chagas F. [Universidade Federal de Campina Grande (DEE/UFCG), PB (Brazil). Dept. de Engenharia Eletrica], E-mail: chagas@dee.ufcg.edu.br

    2009-07-01

    This work describes the development of a synchronous key based on micro controller to the switching of three-phase power transformers, which makes possible the achievement of tests to register the inrush current, and the previous establishment of the instantaneous values of the voltage firstly applied to different phases of the energy process. This key is a value tool to the development electric power system projects and to the teaching and researching activities at the laboratory related to transitory phenomena and electric system protection.

  20. Magnetic model for a horse-spleen ferritin with a three-phase core structure

    Energy Technology Data Exchange (ETDEWEB)

    Jung, J.H.; Eom, T.W. [Quantum Photonic Science Research Center, Department of Physics and Research Institute for Natural Sciences, Hanyang University, Seoul 133-791 (Korea, Republic of); Lee, Y.P., E-mail: yplee@hanyang.ac.kr [Quantum Photonic Science Research Center, Department of Physics and Research Institute for Natural Sciences, Hanyang University, Seoul 133-791 (Korea, Republic of); Rhee, J.Y. [Department of Physics, Sungkyunkwan University, Suwon (Korea, Republic of); Choi, E.H. [Kwangwoon University, Seoul (Korea, Republic of)

    2011-12-15

    The increasing interests in magnetic nanoparticles has prompted research on ferritin, which is naturally a well-defined iron-storage protein in most living organisms. However, the exact magnetic behavior of ferritin is not well understood, because the crystal structures of ferritin and ferrihydrite, its major component, are not fully understood. Briefly, we discuss the previous magnetization models of ferritin and ferrihydrite and we present a new model ({Sigma}3L) of the initial magnetization of ferritin, considering its different phases. The new model includes three Langevin-function terms, which represent three different magnetic moments provided by the likely hydroxide and oxide mineral phases in ferritin. Compared to previous models, our simple model fits the experimental data 12 times better in terms of the sum of least squares. The magnetic independence of each component supports the multi-phase compositional model of the mineral core of horse-spleen ferritin. This {Sigma}3L model gives a quantization of the amounts of the different phases within horse-spleen ferritins that matches other published experimental data: 60-80% ferrihydrite, 15-25% maghemite/magnetite, and 1-10% hematite. - Highlights: > We present a new model ({Sigma}3L) of the initial magnetization of ferritin, considering its different phases. > New model includes three Langevin-function terms, which represent three different magnetic moments provided by ferritin phases. > Compared to previous models, our simple model fits the experimental data 12 times better in terms of the sum of least square. > The magnetic independence of each component supports that ferritin and ferrihydrite are composed of different phases.