WorldWideScience

Sample records for research received additional

  1. RESEARCH OF PROCESS OF AN ALLOYING OF THE FUSED COATINGS RECEIVED FROM THE SUPERFICIAL ALLOYED WIRE BY BORON WITH IN ADDITIONALLY APPLIED ELECTROPLATED COATING OF CHROME AND COPPER

    Directory of Open Access Journals (Sweden)

    V. A. Stefanovich

    2015-01-01

    Full Text Available Researches on distribution of chrome and copper in the fused coating received from the superficial alloyed wire by boron with in additionally applied electroplated coating of chrome and copper were executed. The structure of the fused coating consists of dendrites on which borders the boride eutectic is located. It is established that the content of chrome in dendrites is 1,5– 1,6 times less than in the borid; distribution of copper on structure is uniformed. Coefficients of digestion of chrome and copper at an argon-arc welding from a wire electrode with electroplated coating are established. The assimilation coefficient for chrome is equal to 0,9–1,0; for copper – 0,6–0,75.

  2. The methods of receiving coal water suspension and its use as the modifying additive in concrete

    Science.gov (United States)

    Buyantuyev, S. L.; Urkhanova, L. A.; Lkhasaranov, S. A.; Stebenkova, Y. Y.; Khmelev, A. B.; Kondratenko, A. S.

    2017-01-01

    Results of research of the coal water suspension (CWS) from a cake received in the electrodigit ways in the fluid environment and gas are given in article and also the possibilities of its use as the modifying additive in concrete are considered. Use of a coal cake is perspective as it is a withdrawal of the coal and concentrating enterprises and has extremely low cost. Methods of receiving CWS and possibility of formation of carbon nanomaterials (CNM) are given in their structure. Research and the analysis of a microstructure of a surface of exemplars before electrodigit processing, their element structure, dependence of durability of a cement stone on a look and quantity of an additive of CWS is conducted. For modification of cement the carbon nanomaterials received from the following exemplars of water coal suspensions were used: foams from a cake from a scrubber of the plasma modular reactor, coal water suspension from a cake from electrodigit installation. The product which can find further application for a power engineering as fuel for combustion, and also in structural materials science, in particular, as the modifying additive in concrete allows to receive these methods.

  3. 27 CFR 1.83 - Acquiring or receiving distilled spirits in bulk for addition to wine.

    Science.gov (United States)

    2010-04-01

    ... distilled spirits in bulk for addition to wine. 1.83 Section 1.83 Alcohol, Tobacco Products and Firearms... UNDER THE FEDERAL ALCOHOL ADMINISTRATION ACT, NONINDUSTRIAL USE OF DISTILLED SPIRITS AND WINE, BULK... Bottling § 1.83 Acquiring or receiving distilled spirits in bulk for addition to wine. Persons holding...

  4. Modeling a Change in Flowrate through Detention or Additional Pavement on the Receiving Stream : Final Report

    Science.gov (United States)

    2017-11-01

    The addition or removal of flow from a stream affects the water surface downstream and possibly upstream. The extent of such effects is generally determined by modeling the receiving stream. Guidance that concisely describes how far up/downstream a h...

  5. Digestive microbiota is different in pigs receiving antimicrobials or a feed additive during the nursery period.

    Directory of Open Access Journals (Sweden)

    Cassandra Soler

    Full Text Available Antimicrobials have been used in a prophylactic way to decrease the incidence of digestive disorders during the piglet post-weaning period. Nowadays, it is urgent to reduce their consumption in livestock to address the problem of antimicrobial resistance. In this study, the effect of a product on piglet microbiota has been investigated as an alternative to antimicrobials. Three groups of ten post-weaning pigs were sampled at 0, 15 and 30 days one week post-weaning; the control, antibiotic and feed additive group received a standard post-weaning diet without antibiotics or additives, the same diet as the control group but with amoxicillin and colistin sulphate and the same diet as the control group but with a feed additive (Sanacore-EN, Nutriad International N.V., respectively. The total DNA extracted from faeces was used to amplify the 16S RNA gene for massive sequencing under manufacturer's conditions. Sequencing data was quality filtered and analyzed using QIIME software and suitable statistical methods. In general terms, age modifies significantly the microbiota of the piglets. Thus, the oldest the animal, the highest bacterial diversity observed for the control and the feed additive groups. However, this diversity was very similar in the antibiotic group throughout the trial. Interestingly, a clear increase in abundance of Bacillus and Lactobacillus spp was detected within the feed additive group versus the antibiotic and control groups. In conclusion, the feed additive group had a positive effect in the endogenous microbiota of post-weaning pigs increasing both, the diversity of bacterial families and the abundance of lactic acid bacteria during the post-weaning period.

  6. How much would each researcher receive if competitive government research funding were distributed equally among researchers?

    Directory of Open Access Journals (Sweden)

    Krist Vaesen

    Full Text Available Scientists are increasingly dissatisfied with funding systems that rely on peer assessment and, accordingly, have suggested several proposals for reform. One of these proposals is to distribute available funds equally among all qualified researchers, with no interference from peer review. Despite its numerous benefits, such egalitarian sharing faces the objection, among others, that it would lead to an unacceptable dilution of resources. The aim of the present paper is to assess this particular objection. We estimate (for the Netherlands, the U.S. and the U.K. how much researchers would receive were they to get an equal share of the government budgets that are currently allocated through competitive peer assessment. For the Netherlands, we furthermore estimate what researchers would receive were we to differentiate between researchers working in low-cost, intermediate-cost and high-cost disciplines. Given these estimates, we then determine what researchers could afford in terms of PhD students, Postdocs, travel and equipment. According to our results, researchers could, on average, maintain current PhD student and Postdoc employment levels, and still have at their disposal a moderate (the U.K. to considerable (the Netherlands, U.S. budget for travel and equipment. This suggests that the worry that egalitarian sharing leads to unacceptable dilution of resources is unjustified. Indeed, our results strongly suggest that there is room for far more egalitarian distribution of funds than happens in the highly competitive funding schemes so prevalent today.

  7. Research in Application of Geodetic GPS Receivers in Time Synchronization

    Science.gov (United States)

    Zhang, Q.; Zhang, P.; Sun, Z.; Wang, F.; Wang, X.

    2018-04-01

    In recent years, with the development of satellite orbit and clock parameters accurately determining technology and the popularity of geodetic GPS receivers, Common-View (CV) which proposed in 1980 by Allan has gained widespread application and achieved higher accuracy time synchronization results. GPS Common View (GPS CV) is the technology that based on multi-channel geodetic GPS receivers located in different place and under the same common-view schedule to receiving same GPS satellite signal at the same time, and then calculating the time difference between respective local receiver time and GPST by weighted theory, we will obtain the difference between above local time of receivers that installed in different station with external atomic clock. Multi-channel geodetic GPS receivers have significant advantages such as higher stability, higher accuracy and more common-view satellites in long baseline time synchronization application over the single-channel geodetic GPS receivers. At present, receiver hardware delay and surrounding environment influence are main error factors that affect the accuracy of GPS common-view result. But most error factors will be suppressed by observation data smoothing and using of observation data from different satellites in multi-channel geodetic GPS receiver. After the SA (Selective Availability) cancellation, using a combination of precise satellite ephemeris, ionospheric-free dual-frequency P-code observations and accurately measuring of receiver hardware delay, we can achieve time synchronization result on the order of nanoseconds (ns). In this paper, 6 days observation data of two IGS core stations with external atomic clock (PTB, USNO distance of two stations about 6000 km) were used to verify the GPS common-view theory. Through GPS observation data analysis, there are at least 2-4 common-view satellites and 5 satellites in a few tracking periods between two stations when the elevation angle is 15°, even there will be at least

  8. RESEARCH IN APPLICATION OF GEODETIC GPS RECEIVERS IN TIME SYNCHRONIZATION

    Directory of Open Access Journals (Sweden)

    Q. Zhang

    2018-04-01

    Full Text Available In recent years, with the development of satellite orbit and clock parameters accurately determining technology and the popularity of geodetic GPS receivers, Common-View (CV which proposed in 1980 by Allan has gained widespread application and achieved higher accuracy time synchronization results. GPS Common View (GPS CV is the technology that based on multi-channel geodetic GPS receivers located in different place and under the same common-view schedule to receiving same GPS satellite signal at the same time, and then calculating the time difference between respective local receiver time and GPST by weighted theory, we will obtain the difference between above local time of receivers that installed in different station with external atomic clock. Multi-channel geodetic GPS receivers have significant advantages such as higher stability, higher accuracy and more common-view satellites in long baseline time synchronization application over the single-channel geodetic GPS receivers. At present, receiver hardware delay and surrounding environment influence are main error factors that affect the accuracy of GPS common-view result. But most error factors will be suppressed by observation data smoothing and using of observation data from different satellites in multi-channel geodetic GPS receiver. After the SA (Selective Availability cancellation, using a combination of precise satellite ephemeris, ionospheric-free dual-frequency P-code observations and accurately measuring of receiver hardware delay, we can achieve time synchronization result on the order of nanoseconds (ns. In this paper, 6 days observation data of two IGS core stations with external atomic clock (PTB, USNO distance of two stations about 6000 km were used to verify the GPS common-view theory. Through GPS observation data analysis, there are at least 2–4 common-view satellites and 5 satellites in a few tracking periods between two stations when the elevation angle is 15°, even

  9. NREL Receives Editors' Choice Awards for Supercomputer Research | News |

    Science.gov (United States)

    performance data center, high-bay labs, and office space. NREL's Martha Symko-Davies honored by Women in successful women working in the energy field. As NREL's Director of Partnerships for Energy Systems awards for the Peregrine high-performance computer and the groundbreaking research it made possible. The

  10. Additional oligofructose/inulin does not increase faecal bifidobacteria in critically ill patients receiving enteral nutrition: a randomised controlled trial.

    Science.gov (United States)

    Majid, Hazreen A; Cole, Jayne; Emery, Peter W; Whelan, Kevin

    2014-12-01

    Patients with diarrhoea during enteral nutrition (EN) have been shown to have low faecal bifidobacteria concentrations. Oligofructose/inulin selectively stimulate the growth of bifidobacteria in healthy humans. This study investigates the effect of additional oligofructose/inulin on the gastrointestinal microbiota, short-chain fatty acids (SCFA) and faecal output in patients receiving EN. Adult patients in the intensive care unit (ICU) who were starting EN with a formula containing fibre were randomised to receive 7 g/d of additional oligofructose/inulin or an identically packaged placebo (maltodextrin). A fresh faecal sample was collected at baseline and following at least 7 days of supplementation. Faecal microbiota were analysed using fluorescent in-situ hybridisation and faecal output was monitored daily. Twenty-two patients (mean age 71 years) completed at least 7 days of intervention (mean 12 days). At the end of the intervention, there were no significant differences in the concentrations of bifidobacteria between the groups, after adjusting for baseline values (oligofructose/inulin 6.9 + 1.4, placebo 7.8 + 1.3 log10 cells/g dry faeces, P > 0.05), but there were significantly lower concentrations of Faecalibacterium prausnitzii (7.0 + 1.0 vs. 8.4 + 1.3 log10 cells/g, P = 0.01) and Bacteroides-Prevotella (9.1 + 1.0 vs. 9.9 + 0.9 log10 cells/g, P = 0.05) in patients receiving additional oligofructose/inulin. There were no differences in faecal concentrations of any SCFA, secretory IgA, daily faecal score or incidence of diarrhoea between the two groups. Additional oligofructose/inulin did not increase faecal bifidobacteria in critically ill patients receiving EN, although it did result in lower concentrations of F. prausnitzii and Bacteroides-Prevotella. This trial is registered at http://controlled-trials.com. Identifier: ISRCTN06446184. Copyright © 2013 Elsevier Ltd and European Society for Clinical Nutrition and Metabolism. All

  11. 47 CFR 73.6027 - Class A TV notifications concerning interference to radio astronomy, research and receiving...

    Science.gov (United States)

    2010-10-01

    ... interference to radio astronomy, research and receiving installations. 73.6027 Section 73.6027... radio astronomy, research and receiving installations. An applicant for digital operation of an existing... astronomy, research and receiving installations. [69 FR 69331, Nov. 29, 2004] ...

  12. Stakeholders in psychiatry and their attitudes toward receiving pertinent and incident findings in genomic research

    DEFF Research Database (Denmark)

    Sundby, Anna; Boolsen, Merete Watt; Burgdorf, Kristoffer Solvsten

    2017-01-01

    potential research participants and health professionals toward receiving pertinent and incidental findings. A cross-sectional online survey was developed to investigate the attitudes among research participants toward receiving genomic findings. A total of 2,637 stakeholders responded: 241 persons...... and information that is not of serious health importance. Psychiatrists and clinical geneticists were less positive about receiving genomic findings compared with blood donors. The attitudes toward receiving findings were very positive. Stakeholders were willing to refrain from receiving incidental information......Increasingly more psychiatric research studies use whole genome sequencing or whole exome sequencing. Consequently, researchers face difficult questions, such as which genomic findings to return to research participants and how. This study aims to gain more knowledge on the attitudes among...

  13. Tracking Performance of Upgraded "Polished Panel" Optical Receiver on NASA's 34 Meter Research Antenna

    Science.gov (United States)

    Vilnrotter, Victor

    2013-01-01

    There has been considerable interest in developing and demonstrating a hybrid "polished panel" optical receiver concept that would replace the microwave panels on the Deep Space Network's (DSN) 34 meter antennas with highly polished aluminum panels, thus enabling simultaneous opticaland microwave reception. A test setup has been installed on the 34 meter research antenna at DSS-13 (Deep Space Station 13) at NASA's Goldstone Deep Space Communications Complex in California in order to assess the feasibility of this concept. Here we describe the results of a recent effort todramatically reduce the dimensions of the point-spread function (PSF) generated by a custom polished panel, thus enabling improved optical communications performance. The latest results are compared to the previous configuration in terms of quantifiable PSF improvement. In addition, the performance of acquisition and tracking algorithms designed specifically for the polished panel PSF are evaluated and compared, based on data obtained from real-time tracking of planets and bright stars with the 34 meter research antenna at DSS-13.

  14. Improvement in pulmonary functions and clinical parameters due to addition of breathing exercises in asthma patients receiving optimal treatment

    Directory of Open Access Journals (Sweden)

    Dipti Agarwal

    2017-01-01

    Conclusions: Breathing exercises provided significant improvements in spirometric parameters and significant reduction in breathlessness, wheezing, and nocturnal symptoms as well as requirements of rescue medicines in asthma patients who were receiving optimal asthma treatment.

  15. An action research study; cultural differences impact how manufacturing organizations receive continuous improvement

    Science.gov (United States)

    Kattman, Braden R.

    National culture and organizational culture impact how continuous improvement methods are received, implemented and deployed by suppliers. Previous research emphasized the dominance of national culture over organizational culture. The countries studied included Poland, Mexico, China, Taiwan, South Korea, Estonia, India, Canada, the United States, the United Kingdom, and Japan. The research found that Canada was most receptive to continuous improvement, with China being the least receptive. The study found that organizational culture was more influential than national culture. Isomorphism and benchmarking is driving continuous-improvement language and methods to be more universally known within business. Business and management practices are taking precedence in driving change within organizations.

  16. Campus Grids: Bringing Additional Computational Resources to HEP Researchers

    International Nuclear Information System (INIS)

    Weitzel, Derek; Fraser, Dan; Bockelman, Brian; Swanson, David

    2012-01-01

    It is common at research institutions to maintain multiple clusters that represent different owners or generations of hardware, or that fulfill different needs and policies. Many of these clusters are consistently under utilized while researchers on campus could greatly benefit from these unused capabilities. By leveraging principles from the Open Science Grid it is now possible to utilize these resources by forming a lightweight campus grid. The campus grids framework enables jobs that are submitted to one cluster to overflow, when necessary, to other clusters within the campus using whatever authentication mechanisms are available on campus. This framework is currently being used on several campuses to run HEP and other science jobs. Further, the framework has in some cases been expanded beyond the campus boundary by bridging campus grids into a regional grid, and can even be used to integrate resources from a national cyberinfrastructure such as the Open Science Grid. This paper will highlight 18 months of operational experiences creating campus grids in the US, and the different campus configurations that have successfully utilized the campus grid infrastructure.

  17. The effect of addition of dexamethasone to levobupivacaine in parturients receiving combined spinal-epidural for analgesia for vaginal delivery

    Directory of Open Access Journals (Sweden)

    Amr Samir Wahdan

    2017-01-01

    Full Text Available Background and Aims: Regional analgesia is commonly used for the relief of labour pain, Prolongation of analgesia can be achieved by adjuvant medications. The aim of this randomised controlled trial was to evaluate the efficacy of intrathecal levobupivacaine with dexamethasone for labour analgesia. Methods: A total of 80 females were included in this study, all were primigravidas undergoing vaginal delivery with cervical dilatation ≥4 cm and 50% or more effacement. Forty females were included randomly in either Group L (received intrathecal levobupivacaine 0.25% in 2 mL or Group LD (received intrathecal levobupivacaine 0.25% combined with dexamethasone 4 mg in 2 mL. The primary outcome was the duration of spinal analgesia. Secondary outcomes included the total dose of epidural local anaesthetic given, time to delivery, neonatal outcome and adverse effects. Results: The duration of spinal analgesia was significantly longer in the LD group compared with L group (80.5 ± 12.4 min vs. 57.1 ± 11.5 min, respectively; P< 0.001. In Group LD compared with Group L, time from spinal analgesia to delivery was significantly lower (317.4 ± 98.9 min vs. 372.4 ± 118.8 min, respectively; P = 0.027, and total epidural levobupivacaine consumption was significantly lower (102.4 ± 34.8 mg vs. 120.1 ± 41.9 mg, respectively; P = 0.027. The two groups were comparable with respect to characteristics of sensory and motor block, haemodynamic parameters, pain scores, neonatal outcome and frequency of adverse effects. Conclusion: Intrathecal dexamethasone plus levobupivacaine prolongs the duration of spinal analgesia during combined spinal-epidural CSE for labour analgesia.

  18. RESEARCH OF THE MAIN FORMS OF REFINANCING OF RECEIVABLES OF THE ENTERPRISES AT THE PRESENT STAGE

    Directory of Open Access Journals (Sweden)

    I. V. Sukhomlin

    2014-04-01

    Full Text Available In article modern forms of refinancing of receivables for management of enterprise mutual settlements are investigated, namely: factoring, the accounting of the bills issued by buyers of production, forfeyting, the commercial credit. Advantages of the enterprises are defined at application of factoring operations. Characteristic signs of a forfeyting are defined, its advantages are analysed. Expediency of introduction of the commercial credit on the basis of circulation of bills is analysed.Purpose. To investigate modern forms of refinancing of receivables and to consider possibility of their use at the enterprise. To analyse influence of factoring operations on activity of the enterprises. To define expediency of introduction of the commercial credit on the basis of circulation of bills.Method or methodology of carrying out work. Work is performed by results of research of modern domestic and foreign views on advantages of use of the main forms of refinancing of receivables of the enterprises as means of increase of solvency at the present stage.Results. The main forms of refinancing of receivables, including such as are investigated: factoring, forfeyting, commercial credit. Advantages of the enterprises are defined at application of factoring operations. Characteristic signs of a forfeyting are considered, its advantages are analysed. Expediency of introduction of the commercial credit on the basis of circulation of bills is defined.Scope of results. The recommendations offered in article can be used by the enterprises of Ukraine of all forms of ownership for solvency increase at the present stage.Purchase on Elibrary.ru > Buy now

  19. 48 CFR 1852.235-74 - Additional Reports of Work-Research and Development.

    Science.gov (United States)

    2010-10-01

    ...-Research and Development. 1852.235-74 Section 1852.235-74 Federal Acquisition Regulations System NATIONAL... Provisions and Clauses 1852.235-74 Additional Reports of Work—Research and Development. As prescribed in 1835.070(e), insert a clause substantially the same as the following: Additional Reports of Work—Research...

  20. Research on high-temperature heat receiver in concentrated solar radiation system

    Directory of Open Access Journals (Sweden)

    Estera Przenzak

    2017-01-01

    Full Text Available The article presents the results of experimental and computer simulations studies of the high temperature heat receiver working in the concentrated solar radiation system. In order to study the radiation absorption process and heat exchange, the two types of computer simulations were carried out. The first one was used to find the best location for absorber in the concentrating installation. Ray Tracing Monte Carlo (RTMC method in Trace Pro software was used to perform the optical simulations. The results of these simulations were presented in the form of the solar radiation distribution map and chart. The data obtained in RTMC simulations were used as a second type boundary conditions for Computational Fluid Dynamics (CFD simulations. These studies were used to optimize the internal geometry of the receiver and also to select the most effective flow parameters of the working medium. In order to validate the computer simulations, high temperature heat receiver was tested in experimental conditions. The article presents the results of experimental measurements in the form of temperature, radiation intensity and power graphs. The tests were performed for varied flow rate and receiver location. The experimental and computer simulation studies presented in this article allowed to optimize the configuration of concentrating and heat receiving system.

  1. Marine research in Greece and the additional Greek marine research centres: Progress and present situation

    Science.gov (United States)

    Haritonidis, S.

    1995-03-01

    Greece, as is known, has a coastline of 17 000 km, and over 2000 small and large islands. As expected, the quest of humankind for new sources of matter and energy has been focussed on the sea, with fishery being its primary interest. A number of philosophers and scientists have been involved in the study of this vast ecosystem since ancient times (Aristotle). The political, social and geographical upheavals witnessed in the Greek area, have, however resulted in bringing all these activities to a halt. The first contemporary research work commenced at the end of the 18th century/beginning of the 19th — with marine flora and fauna as its starting point. The first investigations had, of course, been limited to random collections of marine material done in the frame of international exploratory expeditions. Studies became more systematic by the end of the 19th and beginning of the 20th century, with priority being given to the animal kingdom (fish, molluscs, etc.). Investigation of the marine phytobenthos (macrophyceae, phytoplankton) was to follow. The past 40 years research has been more extensive, not limited only to biogeographical evaluations, but also having expanded to physiological and ecological levels. The relevant institutes of Greek universities have all the while watched and contributed to this effort. Today, this kind of research is being supported by the N.M.R.C., the Center of Marine Research, University of Crete, and two research boats which sail the Greek seas. In the ever-changing world, the study of marine flora and fauna has certainly made great progress; however, there are still two big problems to be faced. The first deals with increasing pollution of the seas, the second, with the difficulties in finding and affording adequate financial resources that would enable a more detailed and complete execution of this research work.

  2. CCR’s Douglas Lowy and John Schiller receive the 2017 Lasker~DeBakey Clinical Medical Research Award | Center for Cancer Research

    Science.gov (United States)

    Douglas Lowy, M.D., and John Schiller, Ph.D., of CCR’s Laboratory of Cellular Oncology have received the 2017 Lasker~DeBakey Clinical Medical Research Award for their groundbreaking research leading to the development of human papillomavirus (HPV) vaccines. The Lasker Awards are widely regarded as the country’s most prestigious biomedical research prizes.

  3. NCI at Frederick Employees Receive Awards at the Spring Research Festival | Poster

    Science.gov (United States)

    NCI and Frederick National Laboratory staff members were among those honored at the Spring Research Festival Awards Ceremony on May 28. The ceremony was the culmination of the festival, which was sponsored by the National Interagency Confederation for Biological Research (NICBR), May 4–7. Maj. Gen. Brian Lein, commanding general, U.S. Army Medical Research and Materiel Command

  4. Numerical research of dynamic characteristics in tower solar cavity receiver based on step-change radiation flux

    Science.gov (United States)

    Chen, Zhengwei; Wang, Yueshe; Hao, Yun; Wang, Qizhi

    2013-07-01

    The solar cavity receiver is an important light-energy to thermal-energy convector in the tower solar thermal power plant system. The heat flux in the inner surface of the cavity will show the characteristics of non-continuous step change especially in non-normal and transient weather conditions, which may result in a continuous dynamic variation of the characteristic parameters. Therefore, the research of dynamic characteristics of the receiver plays a very important role in the operation and the control safely in solar cavity receiver system. In this paper, based on the non-continuous step change of radiation flux, a non-linear dynamic model is put forward to obtain the effects of the non-continuous step change radiation flux and step change feed water flow on the receiver performance by sequential modular approach. The subject investigated in our study is a 1MW solar power station constructed in Yanqing County, Beijing. This study has obtained the dynamic responses of the characteristic parameters in the cavity receiver, such as drum pressure, drum water level, main steam flow and main steam enthalpy under step change radiation flux. And the influence law of step-change feed water flow to the dynamic characteristics in the receiver also has been analyzed. The results have a reference value for the safe operation and the control in solar cavity receiver system.

  5. Research of aquatic organism addition influence on the reproduction of yeast cells in the dough

    Directory of Open Access Journals (Sweden)

    Дмитро Павлович Крамаренко

    2016-12-01

    Full Text Available The analysis of the research results of influence of various amounts of aquatic organism additions on the reproduction of yeast cells is given. A positive impact of aquatic organism addition of animal and plant origin in investigated quantities on the reproduction of yeast cells is revealed. The influence of the chemical composition of the aquatic organism additives on the reproduction of yeast cells is proved

  6. Transfer Paths of Research Results to the Practice: Observations From the Receiving End

    Science.gov (United States)

    Findikakis, A. N.

    2005-12-01

    A non-scientific poll of fellow practicing professionals suggests that there is a range of opinions regarding the effectiveness of different ways of becoming acquainted with and using the results of academic research in their practice. Journal articles remain the dominant path for transferring research results to the profession, even though accessing them is becoming more difficult with time. Driven primarily by cost considerations personal and corporate subscriptions seem to be on the decline. Libraries are one of the first victims of cost cutting measures in the industry. Even though the availability of journal articles in electronic form facilitates their availability, their prices are prohibitive. This is especially true during when a professional is searching for a solution to a problem and may have to review several papers on the subject. One colleague suggested that the professional organizations and other publishers of research articles could learn from the experience of the music industry, by lowering the cost of downloading individual papers to something like a dollar per article, recovering thus their production costs through the increase in the volume of purchased articles. The posting on the internet of special reports and dissertations by research institutions is viewed as very useful by those working in practice. The distribution through the internet of reports by federal organizations conducting or sponsoring research, such as the U.S. Geological Survey and the U.S. Environmental Protection Agency is greatly appreciated by the practicing professionals. The use of leading researchers as consultants provides a direct path for bringing research results to the practice, but it is limited to a small number of cases where bringing in a consultant can be justified. Short courses are viewed as an effective way of familiarizing professionals with the latest research findings on specific subjects. The notes distributed in such courses are considered

  7. Research on the Lift-off Effect of Receiving Longitudinal Mode Guided Waves in Pipes Based on the Villari Effect

    Directory of Open Access Journals (Sweden)

    Jiang Xu

    2016-09-01

    Full Text Available The magnetostrictive guided wave technology as a non-contact measurement can generate and receive guided waves with a large lift-off distance up to tens of millimeters. However, the lift-off distance of the receiving coil would affect the coupling efficiency from the elastic energy to the electromagnetic energy. In the existing magnetomechanical models, the change of the magnetic field in the air gap was ignored since the permeability of the rod is much greater than that of air. The lift-off distance of the receiving coil will not affect the receiving signals based on these models. However, the experimental phenomenon is in contradiction with these models. To solve the contradiction, the lift-off effect of receiving the longitudinal mode guided waves in pipes is investigated based on the Villari effect. A finite element model of receiving longitudinal guided waves in pipes is obtained based on the Villari effect, which takes into account the magnetic field in the pipe wall and the air zone at the same time. The relation between the amplitude of the induced signals and the radius (lift-off distance of the receiving coil is obtained, which is verified by experiment. The coupling efficiency of the receiver is a monotonic decline with the lift-off distance increasing. The decay rate of the low frequency wave is slower than the high frequency wave. Additionally, the results show that the rate of change of the magnetic flux in the air zone and in the pipe wall is the same order of magnitude, but opposite. However, the experimental results show that the error of the model in the large lift-off distance is obvious due to the diffusion of the magnetic field in the air, especially for the high frequency guided waves.

  8. Efficacy of Additional Canagliflozin Administration to Type 2 Diabetes Patients Receiving Insulin Therapy: Examination of Diurnal Glycemic Patterns Using Continuous Glucose Monitoring (CGM).

    Science.gov (United States)

    Matsumura, Mihoko; Nakatani, Yuki; Tanka, Seiichi; Aoki, Chie; Sagara, Masaaki; Yanagi, Kazunori; Suzuki, Kunihiro; Aso, Yoshimasa

    2017-08-01

    The efficacy of administering a sodium-glucose cotransporter 2 inhibitor during insulin therapy has not been established. In this study, we examined its effects based on diurnal glycemic patterns using continuous glucose monitoring (CGM). The subjects were 15 patients who had received insulin therapy for 1 year or more. A CGM device was attached to all subjects for 1 week. The administration of canagliflozin at 100 mg was started 4 days after attachment. The mean glucose concentrations, standard deviation (SD), mean amplitude of glycemic excursions (MAGE), mean of daily difference of blood glucose (MODD), and area under the curve (AUC) (≥180, glucose concentrations decreased from 161.1 to 139.1 mg/dL (P AUC of ≥180, i.e., the total area of blood glucose levels at or above 180 on the blood glucose curve of CGM, decreased from 339.1 to 113.6 mg/dL (P AUC of blood glucose levels below 70 on the blood glucose curve of CGM, slightly decreased from 1.6 to 0.3 mg/dL (P = 0.08). The total number of basal insulin units decreased from 128 to 76, and that of bolus insulin decreased from 266 to 154; the dose of insulin could be markedly decreased. In addition, the mean 8-OHdG level decreased from 11.4 to 10.8 ng/mg Cre (P blood glucose changes in type 2 diabetes using insulin. In addition, the results suggest its antioxidant actions. University Hospital Medical Information Network (UMIN no. 000019429).

  9. Lin Receives 2010 Natural Hazards Focus Group Award for Graduate Research

    Science.gov (United States)

    2010-11-01

    Ning Lin has been awarded the Natural Hazards Focus Group Award for Graduate Research, given annually to a recent Ph.D. recipient for outstanding contributions to natural hazards research. Lin's thesis is entitled “Multi-hazard risk analysis related to hurricanes.” She is scheduled to present an invited talk in the Extreme Natural Events: Modeling, Prediction, and Mitigation session (NH20) during the 2010 AGU Fall Meeting, held 13-17 December in San Francisco, Calif. Lin will be formally presented with the award at the Natural Hazards focus group reception on 14 December 2010.

  10. Involving Communities in Deciding What Benefits They Receive in Multinational Research.

    Science.gov (United States)

    Wendler, David; Shah, Seema

    2015-10-01

    There is wide agreement that communities in lower-income countries should benefit when they participate in multinational research. Debate now focuses on how and to what extent these communities should benefit. This debate has identified compelling reasons to reject the claim that whatever benefits a community agrees to accept are necessarily fair. Yet, those who conduct clinical research may conclude from this rejection that there is no reason to involve communities in the process of deciding how they benefit. Against this possibility, the present manuscript argues that involving host communities in this process helps to promote four important goals: (1) protecting host communities, (2) respecting host communities, (3) promoting transparency, and (4) enhancing social value. Published by Oxford University Press on behalf of the Journal of Medicine and Philosophy, Inc. 2015.

  11. A Review of Research on the Literacy of Students with Visual Impairments and Additional Disabilities

    Science.gov (United States)

    Parker, Amy T.; Pogrund, Rona L.

    2009-01-01

    Research on the development of literacy in children with visual impairments and additional disabilities is minimal even though these children make up approximately 65% of the population of children with visual impairments. This article reports on emerging themes that were explored after a review of the literature revealed nine literacy studies…

  12. Research on Capacity Addition using Market Model with Transmission Congestion under Competitive Environment

    Science.gov (United States)

    Katsura, Yasufumi; Attaviriyanupap, Pathom; Kataoka, Yoshihiko

    In this research, the fundamental premises for deregulation of the electric power industry are reevaluated. The authors develop a simple model to represent wholesale electricity market with highly congested network. The model is developed by simplifying the power system and market in New York ISO based on available data of New York ISO in 2004 with some estimation. Based on the developed model and construction cost data from the past, the economic impact of transmission line addition on market participants and the impact of deregulation on power plant additions under market with transmission congestion are studied. Simulation results show that the market signals may fail to facilitate proper capacity additions and results in the undesirable over-construction and insufficient-construction cycle of capacity addition.

  13. Invitations received from potential predatory publishers and fraudulent conferences: a 12-month early-career researcher experience.

    Science.gov (United States)

    Mercier, Eric; Tardif, Pier-Alexandre; Moore, Lynne; Le Sage, Natalie; Cameron, Peter A

    2018-02-01

    This study aims to describe all unsolicited electronic invitations received from potential predatory publishers or fraudulent conferences over a 12-month period following the first publication as a corresponding author of a junior academician. Unsolicited invitations received at an institutional email address and perceived to be sent by predatory publishers or fraudulent conferences were collected. A total of 502 invitations were included of which 177 (35.3%) had subject matter relevant to the recipient's research interests and previous work. Two hundred and thirty-seven were invitations to publish a manuscript. Few disclosed the publication fees (32, 13.5%) but they frequently reported accepting all types of manuscripts (167, 70.5%) or emphasised on a deadline to submit (165, 69.6%). Invitations came from 39 publishers (range 1 to 87 invitations per publisher). Two hundred and ten invitations from a potential fraudulent conference were received. These meetings were held in Europe (97, 46.2%), North America (65, 31.0%), Asia (20.4%) or other continents (5, 2.4%) and came from 18 meeting organisation groups (range 1 to 137 invitations per organisation). Becoming an editorial board member (30), the editor-in-chief (1), a guest editor for journal special issue (6) and write a book chapter (11) were some of the roles offered in the other invitations included while no invitation to review a manuscript was received. Young researchers are commonly exposed to predatory publishers and fraudulent conferences following a single publication as a corresponding author. Academic institutions worldwide need to educate and inform young researchers of this emerging problem. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2018. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

  14. Greek research reactor performance characteristics after addition of beryllium reflector and LEU fuel

    International Nuclear Information System (INIS)

    Deen, J.R.; Snelgrove, J.L.; Papastergiou, C.

    1992-01-01

    The GRR-1 is a 5-MW pool-type, light-water-moderated and-cooled reactor fueled with MTR-type fuel elements. Recently received Be reflector blocks will soon be added to the core to add additional reactivity until fresh LEU fuel arrives. REBUS-3 xy fuel cycle analyses, using burnup dependent cross sections, were performed to assist in fuel management decisions for the water- and Be-reflected HEU nonequilibrium cores. Cross sections generated by EPRI-CELL have been benchmarked to identical VIM Monte Carlo models. The size of the Be-reflected LEU core has been reduced to 30 elements compared to 35 for the HEU water-reflected core, and an equilibrium cycle calculation has been performed

  15. The Responsible Inclusion of Students Receiving Special Education Services for Emotional Disturbance: Unraveling the Practice to Research Gap.

    Science.gov (United States)

    McKenna, John William; Solis, Michael; Brigham, Frederick; Adamson, Reesha

    2018-03-01

    The majority of students receiving special education services for emotional disturbance (ED) receive a significant amount of instruction in general education classrooms, which emphasizes curriculums based on college and career readiness standards. In turn, those teachers who provide instruction to students with ED in inclusive settings are responsible for using evidence-based practices (EBPs) for those teaching situations in which they exist to meet free appropriate public education (FAPE) mandates. However, the identification of EBPs is a necessary pre-condition to eventual school adoption and teacher use of such practices. In this investigation, we completed a synthesis of syntheses to (a) determine the degree to which academic intervention research has focused on students with ED in general education classrooms and (b) identify practices that are effective at improving the academic performance of students with ED in these settings. Overall, few studies were identified. Of those studies identified, half did not disaggregate outcomes for students with ED. A quality indicator coding based on the What Works Clearinghouse (WWC) design standards revealed that no studies with disaggregated outcomes permitted causal inferences. Implications for school practice and areas for future research are discussed.

  16. Does the model of additive effect in placebo research still hold true? A narrative review

    Science.gov (United States)

    Berger, Bettina; Weger, Ulrich; Heusser, Peter

    2017-01-01

    Personalised and contextualised care has been turned into a major demand by people involved in healthcare suggesting to move toward person-centred medicine. The assessment of person-centred medicine can be most effectively achieved if treatments are investigated using ‘with versus without’ person-centredness or integrative study designs. However, this assumes that the components of an integrative or person-centred intervention have an additive relationship to produce the total effect. Beecher’s model of additivity assumes an additive relation between placebo and drug effects and is thus presenting an arithmetic summation. So far, no review has been carried out assessing the validity of the additive model, which is to be questioned and more closely investigated in this review. Initial searches for primary studies were undertaken in July 2016 using Pubmed and Google Scholar. In order to find matching publications of similar magnitude for the comparison part of this review, corresponding matches for all included reviews were sought. A total of 22 reviews and 3 clinical and experimental studies fulfilled the inclusion criteria. The results pointed to the following factors actively questioning the additive model: interactions of various effects, trial design, conditioning, context effects and factors, neurobiological factors, mechanism of action, statistical factors, intervention-specific factors (alcohol, caffeine), side-effects and type of intervention. All but one of the closely assessed publications was questioning the additive model. A closer examination of study design is necessary. An attempt in a more systematic approach geared towards solutions could be a suggestion for future research in this field. PMID:28321318

  17. The potential application of European market research data in dietary exposure modelling of food additives.

    Science.gov (United States)

    Tennant, David Robin; Bruyninckx, Chris

    2018-03-01

    Consumer exposure assessments for food additives are incomplete without information about the proportions of foods in each authorised category that contain the additive. Such information has been difficult to obtain but the Mintel Global New Products Database (GNPD) provides information about product launches across Europe over the past 20 years. These data can be searched to identify products with specific additives listed on product labels and the numbers compared with total product launches for food and drink categories in the same database to determine the frequency of occurrence. There are uncertainties associated with the data but these can be managed by adopting a cautious and conservative approach. GNPD data can be mapped with authorised food categories and with food descriptions used in the EFSA Comprehensive European Food Consumption Surveys Database for exposure modelling. The data, when presented as percent occurrence, could be incorporated into the EFSA ANS Panel's 'brand-loyal/non-brand loyal exposure model in a quantitative way. Case studies of preservative, antioxidant, colour and sweetener additives showed that the impact of including occurrence data is greatest in the non-brand loyal scenario. Recommendations for future research include identifying occurrence data for alcoholic beverages, linking regulatory food codes, FoodEx and GNPD product descriptions, developing the use of occurrence data for carry-over foods and improving understanding of brand loyalty in consumer exposure models.

  18. Research on hardness and tensile properties of A390 alloy with tin addition

    Science.gov (United States)

    Si, Yi

    2018-03-01

    The effect of tin content on hardness and tensile properties of A390 alloys has been discussed. The microstructure of the A390 alloy with tin addition has been surveyed by OM and investigated by SEM. Research showed that β-Sn in the alloy precipitation forms were mainly small blocks and thin strips, particles within the Al2Cu network or large blocks consisting of β-Sn and Al2Cu on Al/Si interfaces or α-Al grain boundaries. Spheroidization of the primary and eutectic silicon was improved due to Sn accretion. With the augment of element tin, hardness of casting alloy is much higher than that of alloy after heat treatment. The elongation and ultimate tensile strength (UTS) were increased in Sn addition from 0 to 1%, which is attributed to the multiple action of Sn.

  19. Corrosion of research reactor aluminium clad spent fuel in water. Additional information

    International Nuclear Information System (INIS)

    2009-12-01

    A large variety of research reactor spent fuel with different fuel meats, different geometries and different enrichments in 235 U are presently stored underwater in basins located around the world. More than 90% of these fuels are clad in aluminium or aluminium based alloys that are notoriously susceptible to corrosion in water of less than optimum quality. Some fuel is stored in the reactor pools themselves, some in auxiliary pools (or basins) close to the reactor and some stored at away-from-reactor pools. Since the early 1990s, when corrosion induced degradation of the fuel cladding was observed in many of the pools, corrosion of research reactor aluminium clad spent nuclear fuel stored in light water filled basins has become a major concern, and programmes were implemented at the sites to improve fuel storage conditions. The IAEA has since then established a number of programmatic activities to address corrosion of research reactor aluminium clad spent nuclear fuel in water. Of special relevance was the Coordinated Research Project (CRP) on Corrosion of Research Reactor Aluminium Clad Spent Fuel in Water (Phase I) initiated in 1996, whose results were published in IAEA Technical Reports Series No. 418. At the end of this CRP it was considered necessary that a continuation of the CRP should concentrate on fuel storage basins that had demonstrated significant corrosion problems and would therefore provide additional insight into the fundamentals of localized corrosion of aluminium. As a consequence, the IAEA started a new CRP entitled Corrosion of Research Reactor Aluminium Clad Spent Fuel in Water (Phase II), to carry out more comprehensive research in some specific areas of corrosion of aluminium clad spent nuclear fuel in water. In addition to this CRP, one of the activities under IAEA's Technical Cooperation Regional Project for Latin America Management of Spent Fuel from Research Reactors (2001-2006) was corrosion monitoring and surveillance of research

  20. Research on the reliability of friction system under combined additive and multiplicative random excitations

    Science.gov (United States)

    Sun, Jiaojiao; Xu, Wei; Lin, Zifei

    2018-01-01

    In this paper, the reliability of a non-linearly damped friction oscillator under combined additive and multiplicative Gaussian white noise excitations is investigated. The stochastic averaging method, which is usually applied to the research of smooth system, has been extended to the study of the reliability of non-smooth friction system. The results indicate that the reliability of friction system can be improved by Coulomb friction and reduced by random excitations. In particular, the effect of the external random excitation on the reliability is larger than the effect of the parametric random excitation. The validity of the analytical results is verified by the numerical results.

  1. Is there an additional benefit of serial NT-proBNP measurements in patients with stable chronic heart failure receiving individually optimized therapy?

    Science.gov (United States)

    Franke, Jennifer; Frankenstein, Lutz; Schellberg, Dieter; Bajrovic, Amer; Wolter, Jan Sebastian; Ehlermann, Philipp; Doesch, Andreas O; Nelles, Manfred; Katus, Hugo A; Zugck, Christian

    2011-12-01

    The role of serial NT-proBNP measurements in patients suffering from chronic systolic heart failure (CHF) who already receive individually optimized pharmacotherapy is still unresolved. NT-proBNP was assessed at baseline and at 6 months follow-up in 504 stable CHF patients treated with individually optimized pharmacotherapy. After assessment of clinical stability at 6 months, patients were followed up for at least 1 year. The combined primary endpoint was defined as death, hospitalization due to cardiac reasons or heart transplantation in 1-year follow-up. We stratified our patients according to two principles: first, a percent change of value (CV) between the first and second measurement of NT-proBNP and secondly, the transformed logarithm of NT-proBNP measured at 6 months. During the follow-up period of 1 year, 50 patients (9.9%) reached the combined primary endpoint. Stratification according to percentage CV was less accurate in predicting endpoint-free survival compared to a classification in categories of lnNT-proBNP measured at 6 months (ROC AUC = 0.615; 95% CI 0.525-0.70 vs. ROC AUC = 0.790; 95% CI 0.721-0.856, respectively). When entered into proportional hazard regression analysis, lnNT-proBNP measured at 6 months remained an independent predictor of the combined primary endpoint with an associated HR of 2.53 (95% CI 1.385-4.280). To date, this is the largest analysis of serial NT-proBNP measurements in patients with CHF receiving individually optimized medical therapy. These data suggest that a single NT-proBNP measurement after 6 months in stable clinical conditions may have higher predictive value than stratification of change in serial measurements.

  2. Detection Performance of Upgraded "Polished Panel" Optical Receiver Concept on the Deep-Space Network's 34 Meter Research Antenna

    Science.gov (United States)

    Vilnrotter, Victor A.

    2012-01-01

    The development and demonstration of a "polished panel" optical receiver concept on the 34 meter research antenna of the Deep Space Network (DSN) has been the subject of recent papers. This concept would enable simultaneous reception of optical and microwave signals by retaining the original shape of the main reflector for microwave reception, but with the aluminum panels polished to high reflectivity to enable focusing of optical signal energy as well. A test setup has been installed on the DSN's 34 meter research antenna at Deep Space Station 13 (DSS-13) of NASA's Goldstone Communications Complex in California, and preliminary experimental results have been obtained. This paper describes the results of our latest efforts to improve the point-spread function (PSF) generated by a custom polished panel, in an attempt to reduce the dimensions of the PSF, thus enabling more precise tracking and improved detection performance. The design of the new mechanical support structure and its operation are described, and the results quantified in terms of improvements in collected signal energy and optical communications performance, based on data obtained while tracking the planet Jupiter with the 34 meter research antenna at DSS-13.

  3. Extraction and Analysis of Information Related to Research & Development Declared Under an Additional Protocol

    International Nuclear Information System (INIS)

    Idinger, J.; Labella, R.; Rialhe, A.; Teller, N.

    2015-01-01

    The additional protocol (AP) provides important tools to strengthen and improve the effectiveness and efficiency of the safeguards system. Safeguards are designed to verify that States comply with their international commitments not to use nuclear material or to engage in nuclear-related activities for the purpose of developing nuclear weapons or other nuclear explosive devices. Under an AP based on INFCIRC/540, a State must provide to the IAEA additional information about, and inspector access to, all parts of its nuclear fuel cycle. In addition, the State has to supply information about its nuclear fuel cycle-related research and development (R&D) activities. The majority of States declare their R&D activities under the AP Articles 2.a.(i), 2.a.(x), and 2.b.(i) as part of initial declarations and their annual updates under the AP. In order to verify consistency and completeness of information provided under the AP by States, the Agency has started to analyze declared R&D information by identifying interrelationships between States in different R&D areas relevant to safeguards. The paper outlines the quality of R&D information provided by States to the Agency, describes how the extraction and analysis of relevant declarations are currently carried out at the Agency and specifies what kinds of difficulties arise during evaluation in respect to cross-linking international projects and finding gaps in reporting. In addition, the paper tries to elaborate how the reporting quality of AP information with reference to R&D activities and the assessment process of R&D information could be improved. (author)

  4. Books Received

    Indian Academy of Sciences (India)

    Home; Journals; Resonance – Journal of Science Education. Books Received. Articles in Resonance – Journal of Science Education. Volume 1 Issue 1 January 1996 pp 118-118 Books Received. Books Received · More Details Fulltext PDF. Volume 1 Issue 2 February 1996 pp 120-120 Books Received. Books Received.

  5. Electronic warfare receivers and receiving systems

    CERN Document Server

    Poisel, Richard A

    2014-01-01

    Receivers systems are considered the core of electronic warfare (EW) intercept systems. Without them, the fundamental purpose of such systems is null and void. This book considers the major elements that make up receiver systems and the receivers that go in them.This resource provides system design engineers with techniques for design and development of EW receivers for modern modulations (spread spectrum) in addition to receivers for older, common modulation formats. Each major module in these receivers is considered in detail. Design information is included as well as performance tradeoffs o

  6. [Research strategies for feed additives and veterinary medicines from side products of Chinese medicine resources industrialization].

    Science.gov (United States)

    Zhao, Ming; Duan, Jin-Ao; Zhang, Sen; Guo, Sheng; Su, Shu-Lan; Wu, Qi-Nan; Tang, Yu-Ping; Zeng, Jian-Guo

    2017-09-01

    The global antimicrobial resistance has been a big challenge to the human health for years. It has to make balance between the safety of animal products and the use of antimicrobials in animal husbandry. Any methods that can minimize or even phase out the use of antimicrobials in animal husbandry should be encouraged. We herein describe the research strategies for feed additives and veterinary medicines from the side products of Chinese medicine resources industrialization. Killing two birds with one stone-besides the major purposes, the rational utilization of non-medicinal parts and wastes of industrialization of Chinese herbal medicines is also achieved under the proposed strategies. Copyright© by the Chinese Pharmaceutical Association.

  7. Various aspects of research of the SI engine with an additional expansion process

    Directory of Open Access Journals (Sweden)

    Noga Marcin

    2017-01-01

    Full Text Available The paper presents an analysis of the results of the both experimental results and theoretical works on the SI engine with additional expansion of exhaust gases, also known as five-stroke engine. The engine like this was constructed at Cracow University of Technology as a retrofitted in-line four cylinder engine in which outer cylinders (1st and 4th work as fired cylinders and inner cylinders (2nd and 3rd work as volume for the additional expansion. The aim of development of such an engine is to gain higher energy recovery ratio of the combusted fuel through the second expansion of exhaust in a separate cylinder. The operating parameters of the engine in various versions were analyzed: as naturally aspirated, supercharged using a turbocharger with a waste-gate valve and a turbocharger with variable nozzle turbine. Selected results of the indicating measurements of the engine with special emphasis on the indicated thermal efficiency were presented. The results pointed out the directions of further optimization of the engine. These results are all the more important, because according to the author’s knowledge, the research on the real object of this type are carried out in only one science center in the world besides Cracow University of Technology.

  8. How to estimate the health benefits of additional research and changing clinical practice

    OpenAIRE

    Claxton, Karl; Griffin, Susan; Koffijberg, Hendrik; McKenna, Claire

    2015-01-01

    A simple extension of standard meta-analysis can provide quantitative estimates of the potential health benefits of further research and of implementing the findings of existing research, which can help inform research prioritisation and efforts to change clinical practice

  9. How to estimate the health benefits of additional research and changing clinical practice

    OpenAIRE

    Claxton, Karl; Griffin, Susan; Koffijberg, Hendrik; McKenna, Claire

    2015-01-01

    A simple extension of standard metaanalysis can provide quantitative estimates of the potential health benefits of further research and of implementing the findings of existing research, which can help inform research prioritisation and efforts to change clinical practice

  10. Communication received from the Member States of the European Community regarding the provision of certain additional information on production, inventories and international transfers of nuclear material and on exports of certain relevant equipment and non-nuclear material

    International Nuclear Information System (INIS)

    1992-12-01

    The document reproduces the text of the note verbale received by the Director General on 30 November 1992 from the Permanent Missions to the Agency of Belgium, Denmark, France, Germany, Greece, Ireland, Italy, Luxembourg, Netherlands, Portugal, Spain and the United Kingdom of Great Britain and Northern Ireland, relating to the provision of certain additional information on production, inventories and international transfer of nuclear material and on exports of certain relevant equipment and non-nuclear material. The note verbale dated 23 November 1992, received by the Director General from the Commission of the European Communities and relating to the same subject, is reproduced as well

  11. Reactor core conversion studies of Ghana: Research Reactor-1 and proposal for addition of safety rod

    International Nuclear Information System (INIS)

    Odoi, H.C.

    2014-06-01

    The inclusion of an additional safety rod in conjunction with a core conversion study of Ghana Research Reactor-1 (GHARR-1) was carried out using neutronics, thermal hydraulics and burnup codes. The study is based on a recommendation by Integrated Safety Assessment for Research Reactors (INSARP) mission to incorporate a safety rod to the reactor safety system as well as the need to replace the reactor fuel with LEU. Conversion from one fuel type to another requires a complete re-evaluation of the safety analysis. Changes to the reactivity worth, shutdown margin, power density and material properties must be taken into account, and appropriate modifications made. Neutronics analysis including burnup was studied followed by thermal hydraulics analyses which comprise steady state and transients. Four computer codes were used for the analysis; MCNP, REBUS, PLTEP and PARET. The neutronics analysis revealed that the LEU core must be operated at 34 Kw in order to attain the flux of 1.0E12 n/cm 2 .s as the nominal flux of the HEU core. The auxiliary safety rod placed at a modified irradiation site gives a better worth than the cadmium capsules. For core excess reactivity of 4 mk, 348 fuel pins would be appropriate for the GHARR-1 LEU core. Results indicate that flux level of 1.0E12 n/cm 2 .s in the inner irradiation channel will not be compromised, if the power of the LEU core is increased to 34 kW. The GHARR-1 core using LEU-U0 2 -12.5% fuel can be operated for 23 shim cycles, with cycles length 2.5 years, for over 57 years at the 17 kW power level. All 23 LEU cycles meet the ∼ 4.0 mk excess reactivity required at the beginning of cycle . For comparison, the MNSR HEU reference core can also be operated for 23 shim cycles, but with a cycle length of 2.0 years for just over 46 years at 15.0kW power level. It is observed that the GHARR-1 core with LEU UO 2 fuel enriched to 12.5% and a power level of 34 kW can be operated ∼25% longer than the current HEU core operated at

  12. 76 FR 34639 - Notice of Proposed Additional Information Collection: Advisory Committee and Research and...

    Science.gov (United States)

    2011-06-14

    ... and Promotion Background Information to include Race, Ethnicity, National Origin, Gender and....gov . Comments submitted by mail must be postmarked 10 business days prior to the deadline to ensure timely receipt. All comments received will be available for public inspection during regular business...

  13. 75 FR 34277 - Federal Acquisition Regulation; FAR Case 2008-007, Additional Requirements for Market Research

    Science.gov (United States)

    2010-06-16

    ... executive agencies. Specifically, the head of the agency must conduct market research before issuing an... million for the procurement of items other than commercial items is required to conduct market research... 10 U.S.C. 2377(c), ``Preliminary Market Research'', to require the head of an agency to conduct...

  14. Communication received from the permanent mission of Austria regarding the provision of certain additional information on production, inventories and international transfers of nuclear material and on exports of certain relevant equipment and non-nuclear material

    International Nuclear Information System (INIS)

    1996-01-01

    The Director General received a note verbale of 13 June 1996 from Permanent Mission of Austria regarding the provision of certain additional information on production, inventories and international transfers of nuclear material and on exports of certain relevant equipment and non-nuclear material. In the light of the request expressed at the end of the note verbale, the text of the note verbale is being circulated

  15. Communication received from the Permanent Mission of Sweden regarding the provision of certain additional information on production, inventories and international transfers of nuclear material and on exports of certain relevant equipment and non-nuclear material

    International Nuclear Information System (INIS)

    1996-01-01

    The document reproduces the text of a note verbale dated 28 June 1996 received by the Director General of IAEA from the Permanent Mission of Sweden through which the Government of Sweden provides, on a voluntary basis, certain additional information on production, inventories and international transfers of nuclear material and on exports of certain relevant equipment and non-nuclear material, in order to assist the Agency in the discharge of its safeguards responsibilities

  16. Communication received from the permanent mission of Finland regarding the provision of certain additional information on production, inventories and international transfers of nuclear material and on exports of certain relevant equipment and non-nuclear material

    International Nuclear Information System (INIS)

    1996-01-01

    The Director General received a note verbale of 8 February 1996 from Permanent Mission of Finland regarding the provision of certain additional information on production, inventories and international transfers of nuclear material and on exports of certain relevant equipment and non-nuclear material. In the light of the request expressed at the and of the note verbale, the text of the note verbale is being circulated

  17. Generalized requirements and decompositions for the design of test parts for micro additive manufacturing research

    DEFF Research Database (Denmark)

    Thompson, Mary Kathryn; Clemmensen, Line Katrine Harder

    2015-01-01

    The design of experimental test parts to characterize micro additive manufacturing (AM) processes is challenging due to the influence of the manufacturing and metrology processes. This work builds on the lessons learned from a case study in the literature to derive generalized requirements and high...... level decompositions for the design of test parts and the design of experiments to characterize micro additive manufacturing processes. While the test parts and the experiments described are still work in progress, the generic requirements derived from them can serve as a starting point for the design...... of other micro additive manufacturing related studies and their decompositions can help structure future work....

  18. 76 FR 14562 - Federal Acquisition Regulation; Additional Requirements for Market Research

    Science.gov (United States)

    2011-03-16

    ... and small disadvantaged business, should be exempt from market research requirements because the... subcontracting opportunities for small- business concerns. Careful attention to market-research strategies is an effective method for creating contract opportunities for small- business concerns. It provides them with an...

  19. Statement Summarizing Research Findings on the Issue of the Relationship Between Food-Additive-Free Diets and Hyperkinesis in Children.

    Science.gov (United States)

    Lipton, Morris; Wender, Esther

    The National Advisory Committee on Hyperkinesis and Food Additives paper summarized some research findings on the issue of the relationship between food-additive-free diets and hyperkinesis in children. Based on several challenge studies, it is concluded that the evidence generally refutes Dr. B. F. Feingold's claim that artificial colorings in…

  20. Research on the Lift-off Effect of Receiving Longitudinal Mode Guided Waves in Pipes Based on the Villari Effect

    OpenAIRE

    Xu, Jiang; Sun, Yong; Zhou, Jinhai

    2016-01-01

    The magnetostrictive guided wave technology as a non-contact measurement can generate and receive guided waves with a large lift-off distance up to tens of millimeters. However, the lift-off distance of the receiving coil would affect the coupling efficiency from the elastic energy to the electromagnetic energy. In the existing magnetomechanical models, the change of the magnetic field in the air gap was ignored since the permeability of the rod is much greater than that of air. The lift-off ...

  1. Defining an additivity framework for mixture research in inducible whole-cell biosensors

    DEFF Research Database (Denmark)

    Martin-Betancor, K; Ritz, Christian; Fernández-Piñas, F

    2015-01-01

    A novel additivity framework for mixture effect modelling in the context of whole cell inducible biosensors has been mathematically developed and implemented in R. The proposed method is a multivariate extension of the effective dose (EDp) concept. Specifically, the extension accounts for differe......A novel additivity framework for mixture effect modelling in the context of whole cell inducible biosensors has been mathematically developed and implemented in R. The proposed method is a multivariate extension of the effective dose (EDp) concept. Specifically, the extension accounts...... for differential maximal effects among analytes and response inhibition beyond the maximum permissive concentrations. This allows a multivariate extension of Loewe additivity, enabling direct application in a biphasic dose-response framework. The proposed additivity definition was validated, and its applicability...... illustrated by studying the response of the cyanobacterial biosensor Synechococcus elongatus PCC 7942 pBG2120 to binary mixtures of Zn, Cu, Cd, Ag, Co and Hg. The novel method allowed by the first time to model complete dose-response profiles of an inducible whole cell biosensor to mixtures. In addition...

  2. Morphology Analysis and Process Research on Novel Metal Fused-coating Additive Manufacturing

    Science.gov (United States)

    Wang, Xin; Wei, Zheng ying; Du, Jun; Ren, Chuan qi; Zhang, Shan; Zhang, Zhitong; Bai, Hao

    2017-12-01

    Existing metal additive manufacturing equipment has high capital costs and slow throughput printing. In this paper, a new metal fused-coating additive manufacturing (MFCAM) was proposed. Experiments of single-track formation were conducted using MFCAM to validate the feasibility. The low melting alloy was selected as the forming material. Then, the effect of process parameters such as the flow rate, deposition velocity and initial distance on the forming morphology. There is a strong coupling effect between the single track forming morphology. Through the analysis of influencing factors to improve the forming quality of specimens. The experimental results show that the twice as forming efficiency as the metal droplet deposition. Additionally, the forming morphology and quality were analyzed by confocal laser scanning microscope and X-ray. The results show that the metal fused-coating process can achieve good surface morphology and without internal tissue defect.

  3. Diversity receiver

    NARCIS (Netherlands)

    2005-01-01

    The invention is directed to the reception of high rate radio signals (for example DVB-T signals) while the receiver is moving at a high speed (for example in or with a car). Two or more antennas (12, 16) are closely spaced and arranged behind each other in the direction of motion (v) for receiving

  4. Research on EHN additive on the diesel engine combustion characteristics in plateau environment

    Science.gov (United States)

    Sun, Zhixin; Li, Ruoting; Wang, Xiancheng; Hu, Chuan

    2017-03-01

    Aiming at the combustion deterioration problem of diesel engine in plateau environment, a bench test was carried out for the effects of EHN additive on combustion characteristics of the diesel engine with intake pressure of 0.68 kPa. Test results showed that with the full load working condition of 1 400 r/min: Cylinder pressure and pressure uprising rate decreased with EHN additive added in, mechanical load on the engine could be relieved; peak value of the heat release rate decreased and its occurrence advanced, ignition delay and combustion duration were shortened; cylinder temperature and exhaust gas temperature declined, thermal load on the engine could be relieved, output torque increased while specific oil consumption decreased, and effective thermal efficiency of diesel engine increased.

  5. Preparation and research on properties of castor oil as a diesel fuel additive

    OpenAIRE

    Nurbakhit Imankulov

    2012-01-01

    The research shows an opportunity of preparing biodiesel fuel on the basis of local diesel fuel and the bioadditive - castor oil. Limiting optimum concentration of introduction of the bioadditive equal was established as 5% mass ratio. The castor oil released from seeds of Palma Christi grown on experimental field. All physical and chemical characteristics of the oil including IR-spectra were determined. Operating conditions of castor oil introduction (temperature, solubility, concentra-tion,...

  6. Additional investigations within the research programme launched after the Chernobyl accident

    International Nuclear Information System (INIS)

    Anon.

    1987-01-01

    The additional investigations concern the determination of the transfer of the fission products I-131, Cs-137, Cs-134, and Te-132 along the pasture-cattle-milk pathway insolving fresh grass, and of the fission products Cs-137 and Cs-134 from winter fodder to milk, beef and veal, and the enrichment of Cs-137 and Sr-90 in the human organism as well as the migration of the fission products Cs-137, Cs-134, Ru-103, and K-40 from the Chernobyl fall-out to the soil. (DG) [de

  7. Biogas Production Experimental Research by Using Sewage Sludge Loading with Biochar Additive

    Directory of Open Access Journals (Sweden)

    Vitalij Kolodynskij

    2017-09-01

    Full Text Available Biogas – ecological fuel, which is assigned to alternative energy sources. It should be noted, that biogas – renewable energy source, which does not require any specific climatic conditions or geographical position of a country. This power source is available and can be successfully produced and used in all countries of the world. The main components of biogas – methane CH4 and carbon monoxide CO2. This gas is formed under anaerobic conditions, when microorganisms decompose biodegradable biomass. In biological sciences biomass means a living matter content, expressed in grams per unit area. Meanwhile, in the energy sector, the definition of biomass is limited and biomass is characterized as fuel source, produced from plant materials and organic waste (food waste, wood, sludge, manure, vegetables, etc.. Currently, to produce biogas from biomass, bioreactors are used worldwide. However, in order to increase the quality and yield of biogas, in the world practice various bioload additives are used: vegetable waste, clay minerals, and a large amount of the protein-containing waste. The goal – to evaluate the impact of biochar on biogas quality and yield using sewage sludge load. It was found, that 10% biochar additive increased average CH4 concentration of 7.9%, reduced the CO2 concentration of 3–4% and totally removed H2S from biogas.

  8. Frederick W. Alt received the 2015 Szent-Györgi Prize for Progress in Cancer Research.

    Science.gov (United States)

    Scully, Peter; Zhao, Jie; Ba, Sujuan

    2016-02-03

    The Szent-Györgyi Prize for Progress in Cancer Research is a prestigious scientific award established by the National Foundation for Cancer Research (NFCR)--a leading cancer research charitable organization in the United States that is committed to supporting scientific research and public education relating to the prevention, early diagnosis, better treatments, and ultimately, a cure for cancer. Each year, the Szent-Györgyi Prize honors an outstanding researcher, nominated by colleagues or peers, who has contributed outstanding, significant research to the fight against cancer, and whose accomplishments have helped improve treatment options for cancer patients. The Prize also promotes public awareness of the importance of basic cancer research and encourages the sustained investment needed to accelerate the translation of these research discoveries into new cancer treatments. This report highlights the pioneering work led by the 2015 Prize winner, Dr. Frederick Alt. Dr. Alt's work in the area of cancer genetics over four decades has helped to shape the very roots of modern cancer research. His work continues to profoundly impact the approaches that doctors around the globe use to diagnose and treat cancer. In particular, his seminal discoveries of gene amplification and his pioneering work on molecular mechanisms of DNA damage repair have helped to usher in the era of genetically targeted therapy and personalized medicine.

  9. Additional transport channel of carbon ions for biological research at the Nuclotron of JINR

    International Nuclear Information System (INIS)

    Yudin, I.P.; Panasik, V.A.; Tyutyunnikov, S.I.

    2011-01-01

    The paper deals with the construction of the 12 C +6 beam transport line for biomedical research at the Nuclotron accelerator complex, JINR. We have studied the scheme and modes of magneto-optical elements of the channel. The results of calculations of the investigated beam transport of carbon ions are presented. The algorithms to control the carbon ion beam in the transportation system are discussed. The choice of the magneto-optical system is motivated. The graphs of the beam envelopes in the channel are given. The scanning control beam functions are considered

  10. Additional transport channel of carbon ions for biological research at the Nuclotron of JINR

    International Nuclear Information System (INIS)

    Yudin, I.P.; Panasik, V.A.; Tyutyunnikov, S.I.

    2012-01-01

    The paper deals with the construction of the beam 12 C +6 transport line for biomedical research at the Nuclotron accelerator complex, JINR. We have studied the scheme and modes of magneto-optical elements of the channel. The results of calculations of the investigated beam transport of carbon ions are presented. The algorithms to control the carbon ion beam in the transportation system are discussed. The choice of the magneto-optical system is motivated. The graphs of the beam envelopes in the channel are given. The scanning control beam functions are considered

  11. Research of cement mixtures with additions of industrial by-products

    Science.gov (United States)

    Papesch, R.; Klus, L.; Svoboda, J.; Zajac, R.

    2017-10-01

    The main goal of the article is the comparison of the possible use of secondary energy products. Used fly ashes, respectively steel dusts in cement mixes derive from production in Moravian-Silesian Region. The research focused on their influence on the chemical and physico-mechanical characteristics of the fresh and solid mixture. The aim was to find suitable formulations for grouting works, highway construction possibly rehabilitation of underground cavities created by mining activities. The introduction is mentioned the history of waste utilization up to current use as a product and the overall state of the problem. The conclusion is an evaluation of possible use in practice, including recommendations to carry out further tests.

  12. Educational and Nonprofit Institutions Receiving Prime Contract Awards for RDT&E (Research, Development, Test and Evaluation), Fiscal Year 1981.

    Science.gov (United States)

    1981-01-01

    SCIENCE & TECH 162 - UNITED KINGDOM MINISTRY OF DEFENCE 2,670 - UN KINGDOM 162 UN KINGDOM 2,670 INSTITUT FUER ATMOSPHAERISCHE 25 - UNIVERSITE RENE ... DESCARTES 10 - GERMANY 25 FRANCE 10 INVERESK RESEARCH INTERNATIONAL 106 - 8,602 UN KINGDOM 106 ISRAEL INSTITUTE OF TECHNOLOGY 55 - ISRAEL 55 KEELE UNIVERSITY

  13. Does Culture Affect how People Receive and Resist Persuasive Messages? Research Proposals about Resistance to Persuasion in Cultural Groups

    OpenAIRE

    Renata Kolodziej-Smith; Daniel Patrick Friesen; Attila Yaprak

    2013-01-01

    Abstract Even though persuasion has been a widely researched topic in consumer behavior, the great majority of these studies have involved American consumers and focused on persuasion itself, with very few addressing resistance to persuasive attempts. None has addressed resistance to persuasion in a cross-cultural context. We aim to contribute to closing this gap in the literature with this paper. Specifically, we aim to expand knowledge of the persuasive process by applying the cultural dime...

  14. Research on the radiation doses to adults receiving from main types of medical X-ray CT examinations

    International Nuclear Information System (INIS)

    Gao Linfeng; Wang Bin; Yao Jie; Qian Aijun; Zheng Junzheng; Zhuo Weihai; Qu Liangyong

    2013-01-01

    To study and master the doses to examinees receiving from the wide spread X-CT examinations, is a key issue for strengthening the medical radiation protection. In the studies of the medical exposure levels during the Eleventh Five-Year Plan period in Shanghai, based on the brands of X-CT scanners and their distributions in different levels of hospitals, a total of 45 sets (about 30% of all) of scanners were selected for the field study. Among the 8 commonly performed examinations, the scan parameters and their relevant dosimetry information for 500 adults were collected, and their typical effective doses were estimated with the dose conversion factors. The results showed that the averages of weighted CT dose index (CTDI w ) were 55.4, 12.5 and 18.4 mGy, and the dose length products (DLP) were averaged to be 603, 294 and 415 mGy·cm, for the skull, chest and abdomen X-CT scans, respectively. The typical effective doses were estimated to be 1.4, 5.3, and 7.5 mSv for adults in the head, chest and abdomen X-CT scans, respectively. The values of CTDI w for skull scans were generally higher than those for the ear canal, eye, or sinus examinations. It is clear that the optimization between the image quality and the radiation dose should be further strengthened. Particular attentions should be paid in selecting the scanning parameters for various types of X-CT scans, and the diagnostic reference levels for X-CT examinations should be continuously improved. (authors)

  15. Experimental researches about the influence of the additives for engine oils upon the work of the engine

    International Nuclear Information System (INIS)

    Dimitrovski, Mile; Mucevski, Kiril

    2003-01-01

    In this paper an attempt to get some cognitions about the influence of the additives for engine oils upon the working parameters of the internal combustion engines is made. During the experimental researches the changes of the basic parameters which determine the work of the engine, such as: the pressure of compression, the noise, the vibrations, the friction of the engine mechanism, the internal cleanliness of the engine and similar, were observed. It was conclude that the use of additives into the engine oil resulted with smoother work of the engine and cleaner exhausted as well. (Author)

  16. Scholarly productivity and professional advancement of junior researchers receiving KL2, K23, or K08 awards at a large public research institution.

    Science.gov (United States)

    Amory, John K; Louden, Diana K N; McKinney, Christy; Rich, Joanne; Long-Genovese, Stacy; Disis, Mary L

    2017-04-01

    How the productivity and careers of KL2 scholars compare with scholars receiving individual K-awards is unknown. The productivity of KL2 scholars (n=21) at our institution was compared with that of K08 (n=34) and K23 (n=26) scholars. KL2 and K23 scholars had greater productivity than K08 scholars ( p =0.01). Professional advancement was similar among groups. At our institution, scholarly productivity and professional advancement did not differ by type of K-award.

  17. International Szent-Györgyi Prize for Progress in Cancer Research: basic and translational research recognition : Mary-Claire King received the 2016 Prize for her pioneering research that demonstrated the first evidence of genetic predisposition to breast cancer.

    Science.gov (United States)

    Hartmann, Hali; Zhao, Jie; Ba, Sujuan

    2017-11-21

    The Szent-Györgyi Prize for Progress in Cancer Research is a prestigious scientific award sponsored by the National Foundation for Cancer Research (NFCR)-a leading cancer research charitable organization in the United States that supports innovative cancer research globally with the ultimate goal to cure cancer. The coveted Szent-Györgyi Prize annually honors a scientist whose seminal discovery or body of work has resulted in, or led toward, notable contributions to cancer prevention, diagnosis, or treatment; and the discovery has had a high direct impact of saving people's lives. In addition, the prize promotes public awareness of the importance of basic cancer research and encourages the sustained investment needed to accelerate the translation of these research discoveries into new cancer treatments. In 2016, NFCR's Szent-Györgyi Prize Selection Committee was unanimous in its decision to recognize an icon in human disease genetics, Dr. Mary-Claire King, for her pioneering research that demonstrated the first evidence of genetic predisposition to breast cancer. Her proof of existence of BRCA1 gene and its location has made genetic screening for breast and ovarian cancers possible, saving lives of many people who are at high risk with inherited BRCA1 mutations.

  18. Research on Mechanisms and Controlling Methods of Macro Defects in TC4 Alloy Fabricated by Wire Additive Manufacturing.

    Science.gov (United States)

    Ji, Lei; Lu, Jiping; Tang, Shuiyuan; Wu, Qianru; Wang, Jiachen; Ma, Shuyuan; Fan, Hongli; Liu, Changmeng

    2018-06-28

    Wire feeding additive manufacturing (WFAM) has broad application prospects because of its advantages of low cost and high efficiency. However, with the mode of lateral wire feeding, including wire and laser additive manufacturing, gas tungsten arc additive manufacturing etc., it is easy to generate macro defects on the surface of the components because of the anisotropy of melted wire, which limits the promotion and application of WFAM. In this work, gas tungsten arc additive manufacturing with lateral wire feeding is proposed to investigate the mechanisms of macro defects. The results illustrate that the defect forms mainly include side spatters, collapse, poor flatness, and unmelted wire. It was found that the heat input, layer thickness, tool path, and wire curvature can have an impact on the macro defects. Side spatters are the most serious defects, mainly because the droplets cannot be transferred to the center of the molten pool in the lateral wire feeding mode. This research indicates that the macro defects can be controlled by optimizing the process parameters. Finally, block parts without macro defects were fabricated, which is meaningful for the further application of WFAM.

  19. Additive manufacturing.

    Science.gov (United States)

    Mumith, A; Thomas, M; Shah, Z; Coathup, M; Blunn, G

    2018-04-01

    Increasing innovation in rapid prototyping (RP) and additive manufacturing (AM), also known as 3D printing, is bringing about major changes in translational surgical research. This review describes the current position in the use of additive manufacturing in orthopaedic surgery. Cite this article: Bone Joint J 2018;100-B:455-60.

  20. Reports on research projects in the field of reactor safety receiving financial aid by the Federal Minister for Research and Technology

    International Nuclear Information System (INIS)

    1981-09-01

    The individual reports are arranged according to the Research Program on the Safety of LWRs 1977-1980 of the BMFT. Another table of contents uses the same classification system as applied in the Nuclear Safety Index of the CEC (Commission of the European Communities) and the OECD (Organization for Economic Cooperation and Development). The reports are marked by current numbers in sequence of their arrangement in this compilation. (orig./HP) [de

  1. Less is often more, but not always: additional evidence that familiarity breeds contempt and a call for future research.

    Science.gov (United States)

    Norton, Michael I; Frost, Jeana H; Ariely, Dan

    2013-12-01

    Ullrich, Krueger, Brod, and Groschupf (2013)-using a replication of the trait paradigm from Norton, Frost, and Ariely (2007)-suggest that less information does not always equal greater liking. We first ground the current debate in a larger historical debate in social psychology regarding the merits of configural versus algebraic models of person perception. We next review (a) related research that has suggested that more information can in some cases lead to more liking and (b) a large body of "real world" data-from friendships, daters, married couples, employment, celebrities, and politics-that suggests that more information often leads to less liking. We then provide an additional replication of our "less is more" effect, using a slight variation of the trait-list paradigm. The existing data suggest a need for further integrative explorations of when familiarity leads to contempt or liking or has no effect. PsycINFO Database Record (c) 2013 APA, all rights reserved.

  2. GNSS Software Receiver for UAVs

    DEFF Research Database (Denmark)

    Olesen, Daniel Madelung; Jakobsen, Jakob; von Benzon, Hans-Henrik

    2016-01-01

    This paper describes the current activities of GPS/GNSS Software receiver development at DTU Space. GNSS Software receivers have received a great deal of attention in the last two decades and numerous implementations have already been presented. DTU Space has just recently started development of ...... of our own GNSS software-receiver targeted for mini UAV applications, and we will in in this paper present our current progress and briefly discuss the benefits of Software Receivers in relation to our research interests....

  3. Factors Associated With Success of Clinician-Researchers Receiving Career Development Awards From the National Institutes of Health: A Longitudinal Cohort Study.

    Science.gov (United States)

    Jagsi, Reshma; Griffith, Kent A; Jones, Rochelle D; Stewart, Abigail; Ubel, Peter A

    2017-10-01

    Understanding the careers of recent career development awardees is essential to guide interventions to ensure gender equity and success in academic medicine. In 2010-2011 (T1) and 2014 (T2), 1,719 clinician-researchers who received new K08 and K23 awards in 2006-2009 were longitudinally surveyed. Multivariable analyses evaluated the influence of factors on success, including demographics, job characteristics, work environment, priorities, and domestic responsibilities. Of 1,275 respondents at T1, 1,066 (493 women; 573 men) responded at T2. Men and women differed in job characteristics, work environment, priorities, and domestic responsibilities. By T2, women had less funding (mean $780,000 vs. $1,120,000, P = .002) and published fewer papers (mean 33 vs. 45). Using a composite measure that considered funding, publications, or leadership to define success, 53.5% (264/493) of women and 67.0% (384/573) of men were successful. Gender differences in success persisted after accounting for other significant predictors-K award type, specialty, award year, work hours, funding institute tier, feeling responsible for participating in department/division administration, importance of publishing prolifically, feeling responsible for contributing to clinical care, importance of publishing high-quality research, collegiality of the mentoring relationship, adequacy of research equipment, and departmental climate. A significant interaction existed between K award type and gender; the gender difference in success was most pronounced among K23 researchers (among whom the odds ratio for females = 0.32). Men and women continue to have different experiences and career outcomes, with important implications for the design of interventions to promote equity and success.

  4. Discrimination and the health of immigrants and refugees: exploring Canada's evidence base and directions for future research in newcomer receiving countries.

    Science.gov (United States)

    Edge, Sara; Newbold, Bruce

    2013-02-01

    Research and practice increasingly suggests discrimination compromises health. Yet the unique experiences and effects facing immigrant and refugee populations remain poorly understood in Canada and abroad. We review current knowledge on discrimination against newcomers in Canada, emphasizing impacts upon health status and service access to identify gaps and research needs. Existing knowledge centers around experiences within health-care settings, differences in perception and coping, mental health impacts, and debates about "non-discriminatory" health-care. There is need for comparative analyses within and across ethno-cultural groups and newcomer classes to better understand factors shaping how discrimination and its health effects are differentially experienced. Women receive greater attention in the literature given their compounded vulnerability. While this must continue, little is known about the experiences of youth and men. Governance and policy discourse analyses would elucidate how norms, institutions and practices shape discriminatory attitudes and responses. Finally, "non-discriminatory health-care" interventions require critical evaluation to determine their effectiveness.

  5. Research of lignite oxidation kinetic parameters modified by CuSO4 and NaNO3 initiation additives

    Directory of Open Access Journals (Sweden)

    Larionov Kirill

    2017-01-01

    Full Text Available An experimental study and subsequent analytical assessment of activation energy change in lignite oxidation process with addition of NaNO3 and CuSO4 mineral salts were conducted. The results showed that injection of catalytic additives leads to reduction of coal activation energy and reaction initial temperature.

  6. 34 CFR 660.32 - What additional selection criteria does the Secretary use for an application for a research...

    Science.gov (United States)

    2010-07-01

    ..., DEPARTMENT OF EDUCATION THE INTERNATIONAL RESEARCH AND STUDIES PROGRAM How Does the Secretary Make a Grant... use for an application for a research project, a survey, or a study? 660.32 Section 660.32 Education... purposes of the International Education Program authorized by part A of title VI of the HEA. (d...

  7. High Gain Advanced GPS Receiver

    National Research Council Canada - National Science Library

    Brown, Alison; Zhang, Gengsheng

    2006-01-01

    NAVSYS High Gain Advanced GPS Receiver (HAGR) uses a digital beam-steering antenna array to enable up to eight GPS satellites to be tracked, each with up to 10 dBi of additional antenna gain over a conventional receiver solution...

  8. Beyond Bullying: Consideration of Additional Research for the Assessment and Prevention of Potential Rampage School Violence in the United States

    Directory of Open Access Journals (Sweden)

    Evonn Welton

    2014-01-01

    Full Text Available For approximately 15 years there have been a number of episodes of rampage school violence in elementary/high school and higher education in the United States. Initial responses included implementation of antibullying programs, disciplinary measures, and increased law security measures. As the incidences have continued, it has become apparent that a more collaborative and interdisciplinary approach is needed for prevention. This paper offers a review of research literature as it applies to proposed innovative strategies for collaborative research, prevention, and intervention in the school setting.

  9. Basic research on lattice structures focused on the reliance of the cross sectional area and additional coatings

    Directory of Open Access Journals (Sweden)

    Kessler Julia

    2017-01-01

    Full Text Available This scientific survey is about periodic lattice structures which are made by Selective Laser Melting (SLM. Selective laser melting is based on Additive Manufacturing. The increased use and increasing demand of lattice structures in different fields of applications forms the necessity of a closer look on complex structures. Lattice structures can be found in different fields of applications for example in lightweight applications, filters and heat exchangers. Because of the expanding of application areas and thus arising requirements, the quality improvement is indispensable. Additive manufacturing and especially the SLM process enable the manufacturing of highly complex shapes and structures. Further it allows the integration of lightweight structures within to be manufactured applications. These high performance structures and applications need specific boundary and process conditions [1-3]. The main aim of this survey is an extraction of important parameters concerning the shape of lattices. A first focus will be on mechanical properties and the therefore necessary tensile tests.

  10. A synopsis of the Defense Advanced Research Projects Agency (DARPA) investment in additive manufacture and what challenges remain

    Science.gov (United States)

    Maher, Michael; Smith, Adrien; Margiotta, Jesse

    2014-03-01

    DARPA's interest in additive manufacture dates back to the mid-80s with seedling programs that developed the foundational knowledge and equipment that led to the Solid Freeform Fabrication program in 1990. The drivers for this program included reducing development times by enabling "tool-less" manufacturing as well as integration of design and fabrication tools. DARPA consistently pushed the boundaries of additive manufacture with follow-on programs that expanded the material suite available for 3-D printing as well as new processes that expanded the technology's capability base. Programs such as the Mesoscopic Integrated Conformal Electronics (MICE) program incorporated functionality to the manufacturing processes through direct write of electronics. DARPA's investment in additive manufacture continues to this day but the focus has changed. DARPA's early investments were focused on developing and demonstrating the technology's capabilities. Now that the technology has been demonstrated, there is serious interest in taking advantage of the attributes unique to the processing methodology (such as customization and new design possibilities) for producing production parts. Accordingly, today's investment at DARPA addresses the systematic barriers to implementation rather than the technology itself. The Open Manufacturing program is enabling rapid qualification of new technologies for the manufacturing environment through the development of new modeling and informatics tools. While the technology is becoming more mainstream, there are plenty of challenges that need to be addressed. And as the technology continues to mature, the agency will continue to look for those "DARPA-hard" challenges that enable revolutionary changes in capability and performance for the Department of Defense.

  11. Adding value in additive manufacturing: researchers in the United Kingdom and Europe look to 3D printing for customization.

    Science.gov (United States)

    Banks, Jim

    2013-01-01

    Having already made a big impact in the medical sector, three-dimensional (3-D) printing technology continues to push the boundaries of cost efficiency, convenience, and customization. It has transformed some aspects of medical device production. However, expectations of the technology are often exaggerated in the media, so we spoke to leading researchers in the field about its practical applications and what can be expected in the near future.

  12. Studies and research concerning BNFP: converting reprocessing plant's fuel receiving and storage area to an away-from-reactor (AFR) storage facility. Final report

    International Nuclear Information System (INIS)

    Cottrell, J.E.; Shallo, F.A.; Musselwhite, E.L.; Wiedemann, G.F.; Young, M.

    1979-09-01

    Converting a reprocessing plant's fuel receiving and storage station into an Away-From-Reactor storage facility is evaluated in this report. An engineering analysis is developed which includes (1) equipment modifications to the facility including the physical protection system, (2) planning schedules for licensing-related activities, and (3) cost estimates for implementing such a facility conversion. Storage capacities are evaluated using the presently available pools of the existing Barnwell Nuclear Fuel Plant-Fuel Receiving and Storage Station (BNFP-FRSS) as a model

  13. Studies and research concerning BNFP: converting reprocessing plant's fuel receiving and storage area to an away-from-reactor (AFR) storage facility. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Cottrell, Jim E.; Shallo, Frank A.; Musselwhite, E Larry; Wiedemann, George F.; Young, Moylen

    1979-09-01

    Converting a reprocessing plant's fuel receiving and storage station into an Away-From-Reactor storage facility is evaluated in this report. An engineering analysis is developed which includes (1) equipment modifications to the facility including the physical protection system, (2) planning schedules for licensing-related activities, and (3) cost estimates for implementing such a facility conversion. Storage capacities are evaluated using the presently available pools of the existing Barnwell Nuclear Fuel Plant-Fuel Receiving and Storage Station (BNFP-FRSS) as a model.

  14. The effectiveness and cost-effectiveness of community-based support for adolescents receiving antiretroviral treatment: an operational research study in South Africa.

    Science.gov (United States)

    Fatti, Geoffrey; Jackson, Debra; Goga, Ameena E; Shaikh, Najma; Eley, Brian; Nachega, Jean B; Grimwood, Ashraf

    2018-02-01

    Adolescents and youth receiving antiretroviral treatment (ART) in sub-Saharan Africa have high attrition and inadequate ART outcomes, and evaluations of interventions improving ART outcomes amongst adolescents are very limited. Sustainable Development Goal (SDG) target 3c is to substantially increase the health workforce in developing countries. We measured the effectiveness and cost-effectiveness of community-based support (CBS) provided by lay health workers for adolescents and youth receiving ART in South Africa. A retrospective cohort study including adolescents and youth who initiated ART at 47 facilities. Previously unemployed CBS-workers provided home-based ART-related education, psychosocial support, symptom screening for opportunistic infections and support to access government grants. Outcomes were compared between participants who received CBS plus standard clinic-based care versus participants who received standard care only. Cumulative incidences of all-cause mortality and loss to follow-up (LTFU), adherence measured using medication possession ratios (MPRs), CD4 count slope, and virological suppression were analysed using multivariable Cox, competing-risks regression, generalized estimating equations and mixed-effects models over five years of ART. An expenditure approach was used to determine the incremental cost of CBS to usual care from a provider perspective. Incremental cost-effectiveness ratios were calculated as annual cost per patient-loss (through death or LTFU) averted. Amongst 6706 participants included, 2100 (31.3%) received CBS. Participants who received CBS had reduced mortality, adjusted hazard ratio (aHR) = 0.52 (95% CI: 0.37 to 0.73; p effectiveness of CBS in reducing attrition ranged from 42.2% after one year to 35.9% after five years. Virological suppression was similar after three years, but after five years 18.8% CBS participants versus 37.2% non-CBS participants failed to achieve viral suppression, adjusted odds ratio = 0

  15. Good practices according to WHO's recommendation for normal labor and birth and women's assessment of the care received: the "birth in Brazil" national research study, 2011/2012.

    Science.gov (United States)

    Baldisserotto, Marcia Leonardi; Theme Filha, Mariza Miranda; da Gama, Silvana Granado Nogueira

    2016-10-17

    The World Health Organization recommends good practices for the conduct of uncomplicated labor and birth, with the aim of improving the quality of and assessment by women of childbirth care. The aim of this study was to evaluate the association between adoption of good practices according to WHO's recommendation for normal labor and birth and assessment by women of the care received. Birth in Brazil is a national hospital-based study with countrywide representation consisting of 23,894 mothers and their newborns, conducted between February 2011 and October 2012. The present study analysed a subsample of this national survey. Postpartum women classified as low risk during pregnancy who had experienced either spontaneous or induced labor were included in this study, totalling 4102 mothers. To estimate the association between assessment by women of the childbirth care received (dependent variable) and good practices according to WHO's recommendation during normal labor and birth (independent variables), a multinomial logistic regression analysis was used and crude and adjusted odds ratios calculated with their 95 % confidence intervals. The good practices associated with positive assessment of the care received by women during labor and birth included the partner's presence, privacy in the birthing place, time available to ask questions, clarity of information received, and empathic support from caregivers during labor and birth. Freedom of movement, free nutrition offered, choice of companions, nonpharmacological analgesia, skin-to-skin contact and breastfeeding in the childbirth room were not associated with the assessment by women of the care received. Our findings reveal the importance to mothers of their relationship with the team of caregivers during labor and birth. Therefore, caregiver teams must be qualified within a more humanistic vision of childbirth health care.

  16. Receiver Test Selection Criteria

    Science.gov (United States)

    2015-03-12

    The DOT requests that GPS manufacturers submit receivers for test in the following TWG categories: - Aviation (non-certified), cellular, general location/navigation, high precision, timing, networks, and space-based receivers - Each receiver should b...

  17. Tropical Tropospheric Ozone from SHADOZ (Southern Hemisphere ADditional Ozonesondes) Network: A Project for Satellite Research, Process Studies, Education

    Science.gov (United States)

    Thompson, Anne M.; Witte, Jacquelyn C.; Oltmans, Samuel J.; Schmidlin, Francis J.; Coetzee, G. J. R.; Hoegger, Bruno; Kirchhoff, V. W. J. H.; Ogawa, Toshihiro; Kawakami, Shuji; Posny, Francoise

    2002-01-01

    The first climatological overview of total, stratospheric and tropospheric ozone in the southern hemisphere tropical and subtropics is based on ozone sounding data from 10 sites comprising the Southern Hemisphere Additional OZonesondes (SHADOZ) network. The period covered is 1998-2000. Observations were made over: Ascension Island; Nairobi, Kenya; Irene, South Africa; Reunion Island; Watukosek, Java; Fiji; Tahiti; American Samoa; San Cristobal, Galapagos; Natal, Brazil. Campaign data were collected on a trans-Atlantic oceanographic cruise and during SAFARI-2000 in Zambia. The ozone data, with simultaneous temperature profiles to approx. 7 hPa and relative humidity to approx. 200 hPa, reside at: . SHADOZ ozone time-series and profiles give a perspective on tropical total, stratospheric and tropospheric ozone. Prominent features are highly variable tropospheric ozone and a zonal wave-one pattern in total (and tropospheric) column ozone. Total, stratospheric and tropospheric column ozone amounts peak between August and November and are lowest between March and May. Tropospheric ozone variability over the Indian and Pacific Ocean displays influences of the Indian Ocean Dipole and convective mixing. Pollution transport from Africa and South America is a seasonal feature. Tropospheric ozone seasonality over the Atlantic Basin shows effects of regional subsidence and recirculation as well as biomass burning. Dynamical and chemical influences appear to be of comparable magnitude though model studies are needed to quantify this.

  18. The prime questions in authentic patient's consultations: a call for additional research on current and new paradigms.

    Science.gov (United States)

    Nguyen, Hanh Thi

    2013-01-01

    Although the 3 prime questions ("What did your doctor tell you the medication is for?" "How did your doctor tell you to take the medication?," and "What did your doctor tell you to expect?") have been recommended as a way to implement an interactive approach to patient's counseling in pharmacy, research examining how these questions are actually used in practice is relatively sparse. Qualitative approaches might assist to inform pertinent questions that might challenge prevailing paradigms. This commentary calls for a close look at how novice pharmacists in training manage these questions in real-life patient's consultations. These examples are aimed to provide preliminary observations about (1) how the prime questions in their original and modified forms are treated by pharmacists in training and patients, and (2) the interactional functions that the prime questions and similar questions may serve. Preliminary observations based on a conversation analysis of these examples show that the open-ended nature of the original prime questions sometimes leads to interactional problems such as delays in patients' responses and pharmacists' revision of the questions. Modified question formats that involve the use of specific knowledge expected to be possessed by a pharmacist, such as declarative questions and Q-word questions with concrete information, may lead to smoother interaction. Finally, questions about the purpose of the therapy may also be used to create opportunities to express empathy toward the patient or to shift the zone of expertise to the doctor. These initial findings suggest a more context sensitive and adaptive approach to communication in pharmacy. Copyright © 2013 Elsevier Inc. All rights reserved.

  19. Clinical research on radioiodine addition of low-doses of lithium carbonate in short-term treatment of Graves hyperthyroidism

    International Nuclear Information System (INIS)

    Zha Jinshun; Jiang Yan; Xu Yuan; Lin Qinxiu; Huang Chunling; Jiang Tingyin

    2014-01-01

    after therapy (t fT3 =5.23, t fT4 =10.14 in group Ⅰ, t fT3 =5.12, t fT4 =9.98 in group Ⅱ, all P<0.01), then decreased gradually to the normal ranges. The fT 3 and fT 4 values in group Ⅱ were much lower than those in group Ⅰ (t fT3 =8.22, t fT4 =19.18, all P<0.01) 30 days after therapy, no significance were found in other time periods. Cure rate of hyperthyroidism was achieved in 36 of the 50 patients (72%) in group Ⅰ and in 38 of the 50 patients (76%) in group Ⅱ without significant difference. There were no significant differences in curative effect of the two groups (χ 2 =0.21, P>0.05). Conclusion: For patients withdrawing of ATD and those with short effective half-time, as well as those intolerant or invalid, the short term addition of lithium to 131 I allows for a better control of thyrotoxia and the completeness of treatment. But there have not been observed that lithium carbonate plus 131 I can improve the long term cure rate of Graves hyperthyroidism. (authors)

  20. Research

    African Journals Online (AJOL)

    ebutamanya

    2015-10-02

    Oct 2, 2015 ... thought to prevent infection, but recent research has proven otherwise. In addition ... One patient had ophthalmalgia and was exposed to. Kaiy for one year and ... migraine, ear infections, tuberculosis, bone fractures, epilepsy,.

  1. A flexible WLAN receiver

    NARCIS (Netherlands)

    Schiphorst, Roelof; Hoeksema, F.W.; Slump, Cornelis H.

    2003-01-01

    Flexible radio receivers are also called Software Defined Radios (SDRs) [1], [2]. The focus of our SDR project [3] is on designing the front end, from antenna to demodulation in bits, of a °exible, multi-standard WLAN receiver. We try to combine an instance of a (G)FSK receiver (Bluetooth) with an

  2. Causes of death in patients with childhood-onset type 1 diabetes receiving dialysis in Japan: Diabetes Epidemiology Research International (DERI) Mortality Study.

    Science.gov (United States)

    Onda, Yoshiko; Nishimura, Rimei; Morimoto, Aya; Sano, Hironari; Utsunomiya, Kazunori; Tajima, Naoko

    2015-01-01

    To investigate the causes of death and how they changed over time in patients with childhood-onset type 1 diabetes who were receiving dialysis. Of the 1384 patients who were diagnosed with type 1 diabetes atdeath trends were expressed according to the duration of dialysis. The leading causes of death were end-stage renal disease (ESRD) (36.3%), cardiovascular disease (CVD) (31.9%), and infections (20.3%). Among CVD, cerebral hemorrhage was the most frequent (38.9%) and showed a significant trend for an increase in the duration of dialysis (P=0.01, the Cochran-Armitage trend test). The mortality from ESRD concentrated within 5 years of dialysis and that from CVD increased after 10 years of dialysis, while the mortality from infections peaked during 5 to 10 years from initiation of dialysis. The leading causes of death in dialysis patients with type 1 diabetes were ESRD, CVD, and infections. As the duration of dialysis increased, however, CVD contributed more to mortality. Special attention should be paid to CVD, particularly cerebral hemorrhage, to improve the long-term prognosis of patients. Copyright © 2015 Elsevier Inc. All rights reserved.

  3. Highly Sensitive Optical Receivers

    CERN Document Server

    Schneider, Kerstin

    2006-01-01

    Highly Sensitive Optical Receivers primarily treats the circuit design of optical receivers with external photodiodes. Continuous-mode and burst-mode receivers are compared. The monograph first summarizes the basics of III/V photodetectors, transistor and noise models, bit-error rate, sensitivity and analog circuit design, thus enabling readers to understand the circuits described in the main part of the book. In order to cover the topic comprehensively, detailed descriptions of receivers for optical data communication in general and, in particular, optical burst-mode receivers in deep-sub-µm CMOS are presented. Numerous detailed and elaborate illustrations facilitate better understanding.

  4. Delphi Accounts Receivable Module -

    Data.gov (United States)

    Department of Transportation — Delphi accounts receivable module contains the following data elements, but are not limited to customer information, cash receipts, line of accounting details, bill...

  5. Food additives

    Science.gov (United States)

    ... GO About MedlinePlus Site Map FAQs Customer Support Health Topics Drugs & Supplements Videos & Tools Español You Are Here: Home → Medical Encyclopedia → Food additives URL of this page: //medlineplus.gov/ency/article/ ...

  6. Solar energy receiver

    Science.gov (United States)

    Schwartz, Jacob

    1978-01-01

    An improved long-life design for solar energy receivers provides for greatly reduced thermally induced stress and permits the utilization of less expensive heat exchanger materials while maintaining receiver efficiencies in excess of 85% without undue expenditure of energy to circulate the working fluid. In one embodiment, the flow index for the receiver is first set as close as practical to a value such that the Graetz number yields the optimal heat transfer coefficient per unit of pumping energy, in this case, 6. The convective index for the receiver is then set as closely as practical to two times the flow index so as to obtain optimal efficiency per unit mass of material.

  7. Cryogenic microwave channelized receiver

    International Nuclear Information System (INIS)

    Rauscher, C.; Pond, J.M.; Tait, G.B.

    1996-01-01

    The channelized receiver being presented demonstrates the use of high temperature superconductor technology in a microwave system setting where superconductor, microwave-monolithic-integrated-circuit, and hybrid-integrated-circuit components are united in one package and cooled to liquid-nitrogen temperatures. The receiver consists of a superconducting X-band four-channel demultiplexer with 100-MHz-wide channels, four commercial monolithically integrated mixers, and four custom-designed hybrid-circuit detectors containing heterostructure ramp diodes. The composite receiver unit has been integrated into the payload of the second-phase NRL high temperature superconductor space experiment (HTSSE-II). Prior to payload assembly, the response characteristics of the receiver were measured as functions of frequency, temperature, and drive levels. The article describes the circuitry, discusses the key issues related to design and implementation, and summarizes the experimental results

  8. Alexandrite Lidar Receiver

    National Research Council Canada - National Science Library

    Wilkerson, Thomas

    2000-01-01

    ...". The chosen vendor, Orca Photonics, In. (Redmond, WA), in close collaboration with USU personnel, built a portable, computerized lidar system that not only is suitable as a receiver for a near IR alexandrite laser, but also contains an independent Nd...

  9. Testing the Grandchildren's Received Affection Scale using Affection Exchange Theory.

    Science.gov (United States)

    Mansson, Daniel H

    2013-04-01

    The purpose of this study was to test the Grandchildren's Received Affection Scale (GRAS) using Affection Exchange Theory (Floyd, 2006). In accordance with Affection Exchange Theory, it was hypothesized that grandchildren's scores on the Trait Affection Received Scale (i.e., the extent to which individuals by nature receive affection) would be related significantly and positively to their reports of received affection from their grandparents (i.e., their scores on the GRAS). Additionally, a research question was asked to explore if grandchildren's received affection from their grandparents is dependent on their grandparent's biological sex or lineage (i.e., maternal vs paternal). Thus, young adult grandchildren (N = 422) completed the GRAS and the Trait Affection Received Scale. The results of zero-order Pearson correlational analyses provided support for the hypothesis, whereas the results of MANOVAs tests only partially support extant grandparent-grandchild theory and research. These findings broaden the scope of Affection Exchange Theory and also bolster the GRAS's utility in future grandparent-grandchild affectionate communication research.

  10. Receiver Gain Modulation Circuit

    Science.gov (United States)

    Jones, Hollis; Racette, Paul; Walker, David; Gu, Dazhen

    2011-01-01

    A receiver gain modulation circuit (RGMC) was developed that modulates the power gain of the output of a radiometer receiver with a test signal. As the radiometer receiver switches between calibration noise references, the test signal is mixed with the calibrated noise and thus produces an ensemble set of measurements from which ensemble statistical analysis can be used to extract statistical information about the test signal. The RGMC is an enabling technology of the ensemble detector. As a key component for achieving ensemble detection and analysis, the RGMC has broad aeronautical and space applications. The RGMC can be used to test and develop new calibration algorithms, for example, to detect gain anomalies, and/or correct for slow drifts that affect climate-quality measurements over an accelerated time scale. A generalized approach to analyzing radiometer system designs yields a mathematical treatment of noise reference measurements in calibration algorithms. By treating the measurements from the different noise references as ensemble samples of the receiver state, i.e. receiver gain, a quantitative description of the non-stationary properties of the underlying receiver fluctuations can be derived. Excellent agreement has been obtained between model calculations and radiometric measurements. The mathematical formulation is equivalent to modulating the gain of a stable receiver with an externally generated signal and is the basis for ensemble detection and analysis (EDA). The concept of generating ensemble data sets using an ensemble detector is similar to the ensemble data sets generated as part of ensemble empirical mode decomposition (EEMD) with exception of a key distinguishing factor. EEMD adds noise to the signal under study whereas EDA mixes the signal with calibrated noise. It is mixing with calibrated noise that permits the measurement of temporal-functional variability of uncertainty in the underlying process. The RGMC permits the evaluation of EDA by

  11. [International regulation of ethics committees on biomedical research as protection mechanisms for people: analysis of the Additional Protocol to the Convention on Human Rights and Biomedicine, concerning Biomedical Research of the Council of Europe].

    Science.gov (United States)

    de Lecuona, Itziar

    2013-01-01

    The article explores and analyses the content of the Council of Europe's Additional Protocol to the Convention on Human Rights and Biomedicine concerning Biomedical Research regarding the standard legal instrument in biomedical research, issued by an international organization with leadership in bioethics. This implies ethics committees are mechanisms of protection of humans in biomedical research and not mere bureaucratic agencies and that a sound inescapable international regulatory framework exists for States to regulate biomedical research. The methodology used focuses on the analysis of the background, the context in which it is made and the nature and scope of the Protocol. It also identifies and analyses the characteristics and functions of ethics committees in biomedical research and, in particular, the information that should be provided to this bodies to develop their functions previously, during and at the end of research projects. This analysis will provide guidelines, suggestions and conclusions for the awareness and training of members of these committees in order to influence the daily practice. This paper may also be of interest to legal practitioners who work in different areas of biomedical research. From this practical perspective, the article examines the legal treatment of the Protocol to meet new challenges and classic issues in research: the treatment of human biological samples, the use of placebos, avoiding double standards, human vulnerability, undue influence and conflicts of interest, among others. Also, from a critical view, this work links the legal responses to develop work procedures that are required for an effective performance of the functions assigned of ethics committees in biomedical research. An existing international legal response that lacks doctrinal standards and provides little support should, however, serve as a guide and standard to develop actions that allow ethics committees -as key bodies for States- to advance in

  12. Communication dated 10 September 2008 received from the Permanent Mission of Egypt to the Agency concerning the High Level Policy Review Seminar of African Regional Cooperative Agreement for Research, Development and Training related to Nuclear Science and Technology (AFRA)

    International Nuclear Information System (INIS)

    2008-01-01

    The Secretariat has received a communication dated 10 September 2008 from the Permanent Mission of Egypt enclosing the documents of the High Level Policy Review Seminar of the African Regional Cooperative Agreement for Research, Development and Training related to Nuclear Science and Technology (AFRA) held in Aswan, Egypt on 28-29 November 2007. The communication, and as requested therein, the enclosures containing the Declaration of Aswan, the Aswan Action Plan and the Profile of the Regional Strategic Cooperative Framework (2008-2013) are circulated herewith for information

  13. HIGH-EFFICIENCY INFRARED RECEIVER

    Directory of Open Access Journals (Sweden)

    A. K. Esman

    2016-01-01

    Full Text Available Recent research and development show promising use of high-performance solid-state receivers of the electromagnetic radiation. These receivers are based on the low-barrier Schottky diodes. The approach to the design of the receivers on the basis of delta-doped low-barrier Schottky diodes with beam leads without bias is especially actively developing because for uncooled receivers of the microwave radiation these diodes have virtually no competition. The purpose of this work is to improve the main parameters and characteristics that determine the practical relevance of the receivers of mid-infrared electromagnetic radiation at the operating room temperature by modifying the electrodes configuration of the diode and optimizing the distance between them. Proposed original design solution of the integrated receiver of mid-infrared radiation on the basis of the low-barrier Schottky diodes with beam leads allows to effectively adjust its main parameters and characteristics. Simulation of the electromagnetic characteristics of the proposed receiver by using the software package HFSS with the basic algorithm of a finite element method which implemented to calculate the behavior of electromagnetic fields on an arbitrary geometry with a predetermined material properties have shown that when the inner parts of the electrodes of the low-barrier Schottky diode is performed in the concentric elliptical convex-concave shape, it can be reduce the reflection losses to -57.75 dB and the standing wave ratio to 1.003 while increasing the directivity up to 23 at a wavelength of 6.09 μm. At this time, the rounded radii of the inner parts of the anode and cathode electrodes are equal 212 nm and 318 nm respectively and the gap setting between them is 106 nm. These parameters will improve the efficiency of the developed infrared optical-promising and electronic equipment for various purposes intended for work in the mid-infrared wavelength range. 

  14. 'Chaos' in superregenerative receivers

    International Nuclear Information System (INIS)

    Commercon, Jean-Claude; Badard, Robert

    2005-01-01

    The superregenerative principle has been known since the early 1920s. The circuit is extremely simple and extremely sensitive. Today, superheterodyne receivers generally supplant superregenerative receivers in most applications because there are several undesirable characteristics: poor selectivity, reradiation, etc. Superregenerative receivers undergo a revival in recent papers for wireless systems, where low cost and very low power consumption are relevant: house/building meters (such as water, energy, gas counter), personal computer environment (keyboard, mouse), etc. Another drawback is the noise level which is higher than that of a well-designed superheterodyne receiver; without an antenna input signal, the output of the receiver hears in an earphone as a waterfall noise; this sound principally is the inherent input noise amplified and detected by the circuit; however, when the input noise is negligible with respect of an antenna input signal, we are faced to an other source of 'noise' self-generated by the superregenerative working. The main objective of this paper concerns this self-generated noise coming from an exponential growing followed by a re-injection process for which the final state is a function of the phase of the input signal

  15. Solar thermal central receivers

    International Nuclear Information System (INIS)

    Vant-Hull, L.L.

    1993-01-01

    Market issues, environmental impact, and technology issues related to the Solar Central Receiver concept are addressed. The rationale for selection of the preferred configuration and working fluid are presented as the result of a joint utility-industry analysis. A $30 million conversion of Solar One to an external molten salt receiver would provide the intermediate step to a commercial demonstration plant. The first plant in this series could produce electricity at 11.2 cents/kWhr and the seventh at 8.2 cents/kWhr, completely competitive with projected costs of new utility plants in 1992

  16. Wideband CMOS receivers

    CERN Document Server

    Oliveira, Luis

    2015-01-01

    This book demonstrates how to design a wideband receiver operating in current mode, in which the noise and non-linearity are reduced, implemented in a low cost single chip, using standard CMOS technology.  The authors present a solution to remove the transimpedance amplifier (TIA) block and connect directly the mixer’s output to a passive second-order continuous-time Σ∆ analog to digital converter (ADC), which operates in current-mode. These techniques enable the reduction of area, power consumption, and cost in modern CMOS receivers.

  17. Receiver gain function: the actual NMR receiver gain

    OpenAIRE

    Mo, Huaping; Harwood, John S.; Raftery, Daniel

    2010-01-01

    The observed NMR signal size depends on the receiver gain parameter. We propose a receiver gain function to characterize how much the raw FID is amplified by the receiver as a function of the receiver gain setting. Although the receiver is linear for a fixed gain setting, the actual gain of the receiver may differ from what the gain setting suggests. Nevertheless, for a given receiver, we demonstrate that the receiver gain function can be calibrated. Such a calibration enables accurate compar...

  18. Campus Projects Receiving "Earmarks."

    Science.gov (United States)

    Schonberger, Benjamin

    1991-01-01

    Specific campus projects that Congress has directed federal agencies to support this year at over 120 colleges and universities are listed. The agencies neither requested support nor sponsored merit-based competitions for the awards. In some cases, the institutions have a history of receiving special federal treatment. (MSE)

  19. Signal Processing for Improved Wireless Receiver Performance

    DEFF Research Database (Denmark)

    Christensen, Lars P.B.

    2007-01-01

    This thesis is concerned with signal processing for improving the performance of wireless communication receivers for well-established cellular networks such as the GSM/EDGE and WCDMA/HSPA systems. The goal of doing so, is to improve the end-user experience and/or provide a higher system capacity...... by allowing an increased reuse of network resources. To achieve this goal, one must first understand the nature of the problem and an introduction is therefore provided. In addition, the concept of graph-based models and approximations for wireless communications is introduced along with various Belief...... Propagation (BP) methods for detecting the transmitted information, including the Turbo principle. Having established a framework for the research, various approximate detection schemes are discussed. First, the general form of linear detection is presented and it is argued that this may be preferable...

  20. Discussing empirical research on the language and culture relationship to inform English as an additional/foreign language pedagogy and teacher education

    Directory of Open Access Journals (Sweden)

    Gloria Gil

    2016-07-01

    Full Text Available Abstract In spite of the existence of a substantial body of theoretical literature that deals with the intersection of language and culture in the field of English as a foreign/additional (EA/FL language teaching and learning, there are very few empirical studies that investigate this issue with real teachers and learners. Therefore, the objective of this paper is to review some of those empirical studies with a view to informing additional/foreign language pedagogy and teacher education.  For that, the paper, first, summarizes some of the main theoretical issues by discussing the different ways in which the relationship of language and culture has been subjacent to EA/FL pedagogies. Then, the paper shows that there are three different types of language-and-culture-related empirical studies: on coursebooks, on teacher cognition, and on classroom interaction and teacher cognition. A review of these types of studies is made by discussing their main findings. Finally, the paper brings about some implications for the field from the findings of the empirical studies and proposes some topics for further research. Key-words: Culture and language relation. English as an additional/foreign language. Empirical studies.   Resumo Apesar da existência de uma vasta literatura teórica que lida com a interseção entre língua e cultura na área de ensino e aprendizagem do inglês como língua adicional/estrangeira (LA/E, existem poucos estudos empíricos que investigam essa questão com professores e alunos reais. Portanto, o objetivo deste trabalho é revisar alguns desses estudos empíricos com o intuito de contribuir com a pedagogia e a formação de professores de inglês como LA/E. Para isso este trabalho, em primeiro lugar, resume algumas das principais questões teóricas, discutindo as diferentes maneiras em que a relação entre língua e cultura tem subjazido às pedagogias do Inglês como LA/E.  Em seguida, o trabalho mostra que há três tipos

  1. Digital Receiver Phase Meter

    Science.gov (United States)

    Marcin, Martin; Abramovici, Alexander

    2008-01-01

    The software of a commercially available digital radio receiver has been modified to make the receiver function as a two-channel low-noise phase meter. This phase meter is a prototype in the continuing development of a phase meter for a system in which radiofrequency (RF) signals in the two channels would be outputs of a spaceborne heterodyne laser interferometer for detecting gravitational waves. The frequencies of the signals could include a common Doppler-shift component of as much as 15 MHz. The phase meter is required to measure the relative phases of the signals in the two channels at a sampling rate of 10 Hz at a root power spectral density measurements in laser metrology of moving bodies. To illustrate part of the principle of operation of the phase meter, the figure includes a simplified block diagram of a basic singlechannel digital receiver. The input RF signal is first fed to the input terminal of an analog-to-digital converter (ADC). To prevent aliasing errors in the ADC, the sampling rate must be at least twice the input signal frequency. The sampling rate of the ADC is governed by a sampling clock, which also drives a digital local oscillator (DLO), which is a direct digital frequency synthesizer. The DLO produces samples of sine and cosine signals at a programmed tuning frequency. The sine and cosine samples are mixed with (that is, multiplied by) the samples from the ADC, then low-pass filtered to obtain in-phase (I) and quadrature (Q) signal components. A digital signal processor (DSP) computes the ratio between the Q and I components, computes the phase of the RF signal (relative to that of the DLO signal) as the arctangent of this ratio, and then averages successive such phase values over a time interval specified by the user.

  2. Best sellers Books received

    African Journals Online (AJOL)

    support systems, philosophy, politics, placebos, research, spirituality, surrogacy and almost 1 000 other concepts and terms. Included among the many contributors are doctors, lawyers, philosophers, theologians, economists, and anthropologists.

  3. Relationship between time to clinical response and outcomes among Pneumonia Outcomes Research Team (PORT) risk class III and IV hospitalized patients with community-acquired pneumonia who received ceftriaxone and azithromycin.

    Science.gov (United States)

    Zasowski, Evan; Butterfield, Jill M; McNutt, Louise-Ann; Cohen, Jason; Cosler, Leon; Pai, Manjunath P; Gottwald, Joseph; Chen, Wen Zhen; Lodise, Thomas P

    2014-07-01

    Recent Food and Drug Administration (FDA) guidance endorses the use of an early clinical response endpoint as the primary outcome for community-acquired bacterial pneumonia (CABP) trials. While antibiotics will now be approved for CABP, in practice they will primarily be used to treat patients with community-acquired pneumonia (CAP). More importantly, it is unclear how achievement of the new FDA CABP early response endpoint translates into clinically applicable real-world outcomes for patients with CAP. To address this, a retrospective cohort study was conducted among adult patients who received ceftriaxone and azithromycin for CAP of Pneumonia Outcomes Research Team (PORT) risk class III and IV at an academic medical center. The clinical response was defined as clinical stability for 24 h with improvement in at least one pneumonia symptom and with no symptom worsening. A classification and regression tree (CART) was used to determine the delay in response time, measured in days, associated with the greatest risk of a prolonged hospital length of stay (LOS) and adverse outcomes (in-hospital mortality or 30-day CAP-related readmission). A total of 250 patients were included. On average, patients were discharged 2 days following the achievement of a clinical response. In the CART analysis, adverse clinical outcomes were higher among day 5 nonresponders than those who responded by day 5 (22.4% versus 6.9%, P = 0.001). The findings from this study indicate that time to clinical response, as defined by the recent FDA guidance, is a reasonable prognostic indicator of real-world effectiveness outcomes among hospitalized PORT risk class III and IV patients with CAP who received ceftriaxone and azithromycin. Copyright © 2014, American Society for Microbiology. All Rights Reserved.

  4. Pressure difference receiving ears

    DEFF Research Database (Denmark)

    Michelsen, Axel; Larsen, Ole Næsbye

    2007-01-01

    Directional sound receivers are useful for locating sound sources, and they can also partly compensate for the signal degradations caused by noise and reverberations. Ears may become inherently directional if sound can reach both surfaces of the eardrum. Attempts to understand the physics...... of the eardrum. The mere existence of sound transmission to the inner surface does not ensure a useful directional hearing, since a proper amplitude and phase relationship must exist between the sounds acting on the two surfaces of the eardrum. The gain of the sound pathway must match the amplitude and phase...... of the sounds at the outer surfaces of the eardrums, which are determined by diffraction and by the arrival time of the sound, that is by the size and shape of the animal and by the frequency of sound. Many users of hearing aids do not obtain a satisfactory improvement of their ability to localize sound sources...

  5. Solar thermal energy receiver

    Science.gov (United States)

    Baker, Karl W. (Inventor); Dustin, Miles O. (Inventor)

    1992-01-01

    A plurality of heat pipes in a shell receive concentrated solar energy and transfer the energy to a heat activated system. To provide for even distribution of the energy despite uneven impingement of solar energy on the heat pipes, absence of solar energy at times, or failure of one or more of the heat pipes, energy storage means are disposed on the heat pipes which extend through a heat pipe thermal coupling means into the heat activated device. To enhance energy transfer to the heat activated device, the heat pipe coupling cavity means may be provided with extensions into the device. For use with a Stirling engine having passages for working gas, heat transfer members may be positioned to contact the gas and the heat pipes. The shell may be divided into sections by transverse walls. To prevent cavity working fluid from collecting in the extensions, a porous body is positioned in the cavity.

  6. Natural Food Additives and Preservatives for Fish-Paste Products: A Review of the Past, Present, and Future States of Research

    OpenAIRE

    Bashir, Khawaja Muhammad Imran; Kim, Jin-Soo; An, Jeong Hyeon; Sohn, Jae Hak; Choi, Jae-Suk

    2017-01-01

    Fish-paste products, also known as fish cakes or surimi-based products, are worldwide favorites. Surimi, a wet protein concentrate of fish muscle, is used as an intermediate raw material to produce surimi seafood. The flavor, texture, taste, shelf-life, and market value of surimi-based products depend on the source of the fish meat, type of applied heat treatment, and additives used to prepare the surimi. While preparing surimi with chemical additives, several problems have been observed, suc...

  7. Modern Trends of Additional Professional Education Development for Mineral Resource Extracting

    Science.gov (United States)

    Borisova, Olga; Frolova, Victoria; Merzlikina, Elena

    2017-11-01

    The article contains the results of development of additional professional education research, including the field of mineral resource extracting in Russia. The paper describes the levels of education received in Russian Federation and determines the place and role of additional professional education among them. Key factors influencing the development of additional professional education are identified. As a result of the research, the authors proved the necessity of introducing additional professional education programs on educational Internet platforms for mineral resource extracting.

  8. CERN apprentice receives award

    CERN Multimedia

    2008-01-01

    Another CERN apprentice has received an award for the quality of his work. Stéphane Küng (centre), at the UIG ceremony last November, presided over by Geneva State Councillor Pierre-François Unger, Head of the Department of Economics and Health. Electronics technician Stéphane Küng was honoured in November by the Social Foundation of the Union Industrielle Genevoise (UIG) as one of Geneva’s eight best apprentices in the field of mechatronics. The 20-year-old Genevan obtained his Federal apprentice’s certificate (Certificat fédéral de capacité - CFC) in June 2007, achieving excellent marks in his written tests at the Centre d’Enseignement Professionnel Technique et Artisanal (CEPTA). Like more than 200 youngsters before him, Stéphane Küng spent part of his four-year sandwich course working at CERN, where he followed many practical training courses and gained valuable hands-on experience in various technical groups and labs. "It’ always very gr...

  9. Pilot-testing the French version of a provisional European organisation for research and treatment of cancer (EORTC) measure of spiritual well-being for people receiving palliative care for cancer.

    Science.gov (United States)

    Lucette, A; Brédart, A; Vivat, B; Young, T

    2014-03-01

    Spiritual well-being is increasingly recognised as an important aspect of patients' quality of life when living with a potentially life-limiting illness such as cancer. The European Organisation for Research and Treatment of Cancer (EORTC) Quality of Life Group is developing a measure for assessing spiritual well-being cross-culturally for people receiving palliative care for cancer. The pilot-testing phase of the study explored potential problems related to the content and administration of a provisional version of this measure. The French version was pilot-tested with 12 patients in a palliative and supportive day care unit in Paris. Participants were asked to complete the measure and the EORTC QLQ-C15-PAL before being interviewed about their responses. The administration of the measure enabled participants to express the difficulties and existential concerns they experienced. The items were not considered intrusive, despite the sensitive topic of the measure. This article considers difficulties with items pertaining to 'religion' and 'spirituality' in the context of French culture. Overall, this measure appears to enhance holistic care, by providing caregivers with a means of broaching spirituality issues, a topic otherwise difficult to discuss in the context of palliative care. © 2013 John Wiley & Sons Ltd.

  10. Solar receiver with integrated optics

    Science.gov (United States)

    Jiang, Lun; Winston, Roland

    2012-10-01

    The current challenge for PV/Thermal (PV/T) systems is the reduction of radiation heat loss. Compared to solar thermal selective coating, the solar cells cannot be used as an efficient thermal absorber due to their large emissivity of the encapsulation material. Many commercial PV/T products therefore require a high concentration (more than 10x) to reach an acceptable thermal efficiency for their receivers. Such a concentration system inevitably has to track or semi-track, which induces additional cost and collects only the direct radiation from the sun. We propose a new PV/T design using a vacuum encapsulated thin film cell to solve this problem. The proposed design also collects the diffuse sun light efficiently by using an external compound parabolic concentrator (XCPC). Since the transparent electrode (TCO) of thin film cell is inherently transparent in visible light and reflective beyond infrared, this design uses this layer instead of the conventional solar cell encapsulation as the outmost heat loss surface. By integrating such a vacuum design with a tube shaped absorber, we reduce the complexity of conducting the heat energy and electricity out of the device. A low concentration standalone non-tracking solar collector is proposed in this paper. We also analyzed the thermosyphon system configuration using heat transfer and ray tracing models. The economics of such a receiver are presented.

  11. Interviews with information receivers

    International Nuclear Information System (INIS)

    1997-11-01

    The Waste Policy Institute (WPI), through a cooperative agreement with the U.S. Department of Energy's (DOE) Office of Science and Technology (OST), conducted telephone interviews with people who requested OST publications to better understand why they wanted information from OST, how they used the information, and whether the information met their needs. Researchers selected 160 people who requested one of the two OST publications-either the Technology Summary Series (Rainbow Books) or the Initiatives newsletter. Of the 160 selected, interviewers spoke with 79 people nationwide representing six stakeholder audience categories

  12. Determination of the Composition and Quantity of Phthalate Ester Additives in PVC Children's Toys. Greenpeace Research Laboratories Technical Note 06/97.

    Science.gov (United States)

    Stringer, Ruth; Labounskaia, Irina; Santillo, David; Johnston, Paul; Siddorn, John; Stephenson, Angela

    Polyvinyl chloride (vinyl or PVC) is widely used in toys and other children's products. This study, conducted by Greenpeace, examined the composition and quantity of phthalate ester additives in children's PVC toys, used to give the toys added flexibility. Drawn from 17 countries, a total of 71 toys designed to be chewed by babies and young…

  13. Radiation Doses Received by the Irish Population

    International Nuclear Information System (INIS)

    Colgan, P.A.; Organo, C.; Hone, C.; Fenton, D.

    2008-05-01

    Some chemical elements present in the environment since the Earth was formed are naturally radioactive and exposure to these sources of radiation cannot be avoided. There have also been additions to this natural inventory from artificial sources of radiation that did not exist before the 1940s. Other sources of radiation exposure include cosmic radiation from outer space and the use of radiation in medical diagnosis and treatment. There can be large variability in the dose received by invividual members of the population from any given source. Some sources of radiation expose every member of the population while, in other cases, only selected individuals may be exposed. For example, natural radioactivity is found in all soils and therefore everybody receives some radiation dose from this activity. On the other hand, in the case of medical exposures, only those who undergo a medical procedure using radiation will receive a radiation dose. The Radiological Protection Institute of Ireland (RPII) has undertaken a comprehensive review of the relevant data on radiation exposure in Ireland. Where no national data have been identified, the RPII has either undertaken its own research or has referred to the international literature to provide a best estimate of what the exposure in Ireland might be. This has allowed the relative contribution of each source to be quantified. This new evaluation is the most up-to-date assessment of radiation exposure and updates the assessment previously reported in 2004. The dose quoted for each source is the annual 'per caput' dose calculated on the basis of the most recently available data. This is an average value calculated by adding the doses received by each individual exposed to a given radiation source and dividing the total by the current population of 4.24 million. All figures have been rounded, consistent with the accuracy of the data. In line with accepted international practice, where exposure takes place both indoors and

  14. Receiver Heterogeneity Helps

    DEFF Research Database (Denmark)

    Kovács, Erika R.; Pedersen, Morten Videbæk; Roetter, Daniel Enrique Lucani

    2014-01-01

    Heterogeneity amongst devices and desired service are commonly seen as a source of additional challenges for setting up an efficient multi-layer multicast service. In particular, devices requiring only the base layer can become a key bottleneck to the performance for other devices. This paper...... studies the case of a wireless multi-layer multicast setting and shows that the judicious use of network coding allows devices with different computational capabilities to trade-off processing complexity for an improved quality of service. As a consequence, individual devices can determine their required...... effort, while bringing significant advantages to the system as a whole. Network coding is used as a key element to reduce signaling in order to deliver the multicast service. More importantly, our proposed approach focuses on creating some structure in the transmitted stream by allowing inter-layer...

  15. The Issues of the Management of Receivables: Lithuanian Case

    Directory of Open Access Journals (Sweden)

    Remeikiene Rita

    2016-06-01

    Full Text Available Constant changes in business environment determine the significance of receivables to business. The analysis of the current situation in Lithuania has revealed that a substantial part of business enterprises are facing the problem of overdue receivables. This issue emerged as extremely topical after the beginning of the economic crisis in 2008. A number of scientific studies confirmed that the level of receivables has a significant impact not only on smooth business operation but also on operational results and serves as the cause of numerous economic and social problems, faced by both business enterprises and the state. Rising level of receivables determines slower recovery of total economics because it has a negative impact on the sustainability of the public sector of the country. In addition, the scientists highlight economic problems such as production capacity losses, general decrease in competitiveness and failure to satisfy the debt claims. The social problems include the increase in unemployment rate, fall of living standards, dissatisfaction with poor economics of the country and uncertainty about the future. The aim of this article is to analyse the impact of receivables on business in Lithuania. The methods of the research include scientific literature analysis and statistical data analysis.

  16. Research

    African Journals Online (AJOL)

    ebutamanya

    2016-04-22

    Apr 22, 2016 ... Papulosquamous disorders, Infectious disorders, Connective tissue diseases, Bullous disorders, ... surgical pathology specimen received within the study period. The modal age ... enable appropriate management. ... basic clinical data including age, gender were noted. ... Confidentiality of the identity of the.

  17. Research

    African Journals Online (AJOL)

    2014-05-18

    May 18, 2014 ... An area that has not received adequate attention is the extent to which .... Students require numerous skills to manage their own patient load at the different .... Theory. Planning. A ect. Intervention. Overall preparedness. Fig. 1.

  18. Research

    African Journals Online (AJOL)

    abp

    2015-02-27

    Feb 27, 2015 ... of diverse, handy, attractive and miniature items in modern day society. The accessibility to modern day communication devices and ... by receiving answers through the device with accomplice outside ... Okeowo in his book.

  19. Natural Food Additives and Preservatives for Fish-Paste Products: A Review of the Past, Present, and Future States of Research

    Directory of Open Access Journals (Sweden)

    Khawaja Muhammad Imran Bashir

    2017-01-01

    Full Text Available Fish-paste products, also known as fish cakes or surimi-based products, are worldwide favorites. Surimi, a wet protein concentrate of fish muscle, is used as an intermediate raw material to produce surimi seafood. The flavor, texture, taste, shelf-life, and market value of surimi-based products depend on the source of the fish meat, type of applied heat treatment, and additives used to prepare the surimi. While preparing surimi with chemical additives, several problems have been observed, such as a lack of unique characteristics, inferior acceptability, and poor functionality. Various types of fish-paste products have been developed by using different ingredients (e.g., vegetables, seafood, herbs and oriental medicines, grains and roots including carrots, and functional food materials. However, a systematic review of fish-paste products prepared using natural food additives has not yet been performed. Therefore, the quality characteristics of fish-paste products and their functionalities were elucidated in this study. With the increasing demand for surimi seafood products, the functional properties, physiochemical properties, and shelf-life of surimi-based products need to be improved. This review will aid the preparation of new value-added products in the surimi industry.

  20. Overcoming the Challenges of BeiDou Receiver Implementation

    Directory of Open Access Journals (Sweden)

    Mohammad Zahidul H. Bhuiyan

    2014-11-01

    Full Text Available Global Navigation Satellite System (GNSS-based positioning is experiencing rapid changes. The existing GPS and the GLONASS systems are being modernized to better serve the current challenging applications under harsh signal conditions. These modernizations include increasing the number of transmission frequencies and changes to the signal components. In addition, the Chinese BeiDou Navigation Satellite system (BDS and the European Galileo are currently under development for global operation. Therefore, in view of these new upcoming systems the research and development of GNSS receivers has been experiencing a new upsurge. In this article, the authors discuss the main functionalities of a GNSS receiver in view of BDS. While describing the main functionalities of a software-defined BeiDou receiver, the authors also highlight the similarities and differences between the signal characteristics of the BeiDou B1 open service signal and the legacy GPS L1 C/A signal, as in general they both exhibit similar characteristics. In addition, the authors implement a novel acquisition technique for long coherent integration in the presence of NH code modulation in BeiDou D1 signal. Furthermore, a simple phase-preserved coherent integration based acquisition scheme is implemented for BeiDou GEO satellite acquisition. Apart from the above BeiDou-specific implementations, a novel Carrier-to-Noise-density ratio estimation technique is also implemented in the software receiver, which does not necessarily require bit synchronization prior to estimation. Finally, the authors present a BeiDou-only position fix with the implemented software-defined BeiDou receiver considering all three satellite constellations from BDS. In addition, a true multi-GNSS position fix with GPS and BDS systems is also presented while comparing their performances for a static stand-alone code phase-based positioning.

  1. Transmit-receive eddy current probes

    International Nuclear Information System (INIS)

    Obrutsky, L.S.; Sullivan, S.P.; Cecco, V.S.

    1997-01-01

    In the last two decades, due to increased inspection demands, eddy current instrumentation has advanced from single-frequency, single-output instruments to multifrequency, computer-aided systems. This has significantly increased the scope of eddy current testing, but, unfortunately, it has also increased the cost and complexity of inspections. In addition, this approach has not always improved defect detectability or signal-to-noise. Most eddy current testing applications are still performed with impedance probes, which have well known limitations. However, recent research at AECL has led to improved eddy current inspections through the design and development of transmit-receive (T/R) probes. T/R eddy current probes, with laterally displaced transmit and receive coils, present a number of advantages over impedance probes. They have improved signal-to-noise ratio in the presence of variable lift-off compared to impedance probes. They have strong directional properties, permitting probe optimization for circumferential or axial crack detection, and possess good phase discrimination to surface defects. They can significantly increase the scope of eddy current testing permitting reliable detection and sizing of cracks in heat exchanger tubing as well as in welded areas of both ferritic and non-ferromagnetic components. This presentation will describe the operating principles of T/R probes with the help of computer-derived normalized voltage diagrams. We will discuss their directional properties and analyze the advantages of using single and multiple T/R probes over impedance probes for specific inspection cases. Current applications to surface and tube testing and some typical inspection results will be described. (author)

  2. Research

    African Journals Online (AJOL)

    ebutamanya

    2015-03-02

    Mar 2, 2015 ... Joseph Daniels1,&, Ruth Nduati1,2, James Kiarie1,3, Carey Farquhar1,4,5 .... or basic science research career (Socio-Behavioral Research, .... a research environment that supports knowledge sharing to develop research ...

  3. Research

    African Journals Online (AJOL)

    abp

    2017-10-18

    Oct 18, 2017 ... Key words: Risk sexual behavior, private college, multiple sexual partners, consistent condom use. Received: ... Introduction: Risk sexual practice among students from public universities/colleges is common in Ethiopia. However, little has ... partners is an important indicator of risk sexual behavior. Many.

  4. Research

    African Journals Online (AJOL)

    abp

    2012-06-06

    Jun 6, 2012 ... Key words: Oestradiol, risk, breast cancer, women, sub-sahara Africa. Received: 06/01/2012 .... Further management followed depending on the results of the test. Needle and ... Cases had significantly lower body mass index than the controls. The age at .... risk of breast cancer. Annals of internal medicine.

  5. Research

    African Journals Online (AJOL)

    abp

    2017-11-07

    Nov 7, 2017 ... Key words: Rational drug use, prescribing indicators, patient indicators, University of Cape Coast Hospital, Ghana, antibiotic prescription. Received: ... were generally not satisfactory with a low patronage of STG among prescribers. In order .... respiratory infections (29.9%), followed by urinary tract infections.

  6. Research

    African Journals Online (AJOL)

    abp

    2017-09-05

    Sep 5, 2017 ... HIV-infected patients aged ≥ 18 years, who received either stavudine or zidovudine or tenofovir disoproxil fumarate-based regimens. Using systematic ... not last long on them due to new possible side effects [9]. Studies ... these limitations, designing strategies aimed at prolonging the use of the original ...

  7. Research

    African Journals Online (AJOL)

    abp

    2015-01-20

    Jan 20, 2015 ... ... which permits unrestricted use, distribution, and reproduction in any ... unsafe human waste disposal systems, inadequacy and lack of safe ... hence received an interview after providing the stool sample. This makes the response rate to be 100%. .... that prohibits the transmission of intestinal helminths.

  8. Research

    African Journals Online (AJOL)

    abp

    2015-09-09

    Sep 9, 2015 ... stage systematic sampling design from the three provinces. Instrument ... It was based on a question-and-answer information brochure derived from the ... grade 12 education and 11.9% had a post-secondary school education ... to enable South African citizens to receive good quality healthcare at any time ...

  9. Research

    African Journals Online (AJOL)

    abp

    Received: 22/10/2016 - Accepted: 16/08/2017 - Published: 27/09/2017. Abstract. Introduction: ..... Tate JE, Burton AH, Boschi-Pinto C, Steele AD, Duque J,. Parashar UD. ... Barril PA, Martinez LC, Giordano MO, Castello AA, Rota RP, Isa.

  10. Research

    African Journals Online (AJOL)

    2014-05-02

    May 2, 2014 ... laboratory data places the medical laboratory scientist in a prime position ... healthcare centres in a local government area showed that none of them had received in-service training during the 2 years before the study.[10] The .... procedures for safe use of recombinant DNA technology and transport of.

  11. Research

    African Journals Online (AJOL)

    abp

    2017-09-29

    Sep 29, 2017 ... Key words: Irritable bowel syndrome, adolescents, risk factors, subtypes. Received: ... Physicians who attend to children need to have a high index of suspicion for ... the patient has both constipation and diarrhea picture [4,5]. These ..... within the last 2 months and thus there lies the possibility of recall bias.

  12. Research

    African Journals Online (AJOL)

    abp

    29 avr. 2016 ... Mots clés: Accident vasculaire cérébrale, doppler transcrânien, drépanocytose, enfant. Received: 17/05/2015 - Accepted: 07/03/2016 - Published: ... original work is properly cited. Pan African Medical Journal – ISSN: 1937- 8688 ..... Aracaju, Northeast-Brazil. Arq Neuropsiquiatr. 2008 Jun; 66(2):. 360-4.

  13. Research

    African Journals Online (AJOL)

    abp

    2016-09-20

    Sep 20, 2016 ... Key words: Breast cancer, sexual functioning, satisfaction, quality life, body image, culture, depression, anxiety. Received: 25/07/2016 .... (Hospital anxiety and depression scale), which is a structured self- administered .... the impact of breast cancer on sexual activity which differs from one couple to another ...

  14. Research

    African Journals Online (AJOL)

    ebutamanya

    Key words: AIDS, antiretroviral, CD4, HIV, retention. Received: 07/07/2014 - Accepted: 12/10/2015 - Published: 14/10/2015 ..... across Africa, estimated a median retention in care for 12 months after treatment initiation to be 79.4%, .... presented at Fifth IAS Conference on HIV Pathogenesis,. Treatment and Prevention, Cape ...

  15. Research

    African Journals Online (AJOL)

    raoul

    2011-04-16

    Apr 16, 2011 ... Information on demographics, history of pregnancy, diseases and outcome of the newborns .... (57.5%) were more likely to attend UTHY ANC than HIV negative mothers ... of HIV positive mothers received ion and folate tablets against 157 ... nutritional counseling, iron and folic acid for anemia prophylaxis.

  16. Optimization of Passive Coherent Receiver System Placement

    Science.gov (United States)

    2013-09-01

    spheroid object with a constant radar cross section (RCS). Additionally, the receiver and transmitters are assumed to be notional isotropic antennae...software- defined radio for equatorial plasma instability studies,” Radio Science, vol. 48, pp. 1–11. Aug. 2013. [2] P. C. Zhang and B. Y. Li, “Passive

  17. Artificial intelligence in neurodegenerative disease research: use of IBM Watson to identify additional RNA-binding proteins altered in amyotrophic lateral sclerosis.

    Science.gov (United States)

    Bakkar, Nadine; Kovalik, Tina; Lorenzini, Ileana; Spangler, Scott; Lacoste, Alix; Sponaugle, Kyle; Ferrante, Philip; Argentinis, Elenee; Sattler, Rita; Bowser, Robert

    2018-02-01

    Amyotrophic lateral sclerosis (ALS) is a devastating neurodegenerative disease with no effective treatments. Numerous RNA-binding proteins (RBPs) have been shown to be altered in ALS, with mutations in 11 RBPs causing familial forms of the disease, and 6 more RBPs showing abnormal expression/distribution in ALS albeit without any known mutations. RBP dysregulation is widely accepted as a contributing factor in ALS pathobiology. There are at least 1542 RBPs in the human genome; therefore, other unidentified RBPs may also be linked to the pathogenesis of ALS. We used IBM Watson ® to sieve through all RBPs in the genome and identify new RBPs linked to ALS (ALS-RBPs). IBM Watson extracted features from published literature to create semantic similarities and identify new connections between entities of interest. IBM Watson analyzed all published abstracts of previously known ALS-RBPs, and applied that text-based knowledge to all RBPs in the genome, ranking them by semantic similarity to the known set. We then validated the Watson top-ten-ranked RBPs at the protein and RNA levels in tissues from ALS and non-neurological disease controls, as well as in patient-derived induced pluripotent stem cells. 5 RBPs previously unlinked to ALS, hnRNPU, Syncrip, RBMS3, Caprin-1 and NUPL2, showed significant alterations in ALS compared to controls. Overall, we successfully used IBM Watson to help identify additional RBPs altered in ALS, highlighting the use of artificial intelligence tools to accelerate scientific discovery in ALS and possibly other complex neurological disorders.

  18. Evaluation of second-generation central receiver technologies

    International Nuclear Information System (INIS)

    Kolb, G.L.; Chavez, J.M.; Klimas, P.; Meinecke, W.; Becker, M.; Kiera, M.

    1993-01-01

    This paper summarizes the results of a study performed by the US and Germany to assess the technical and economic potential of central receiver power plants and to identify the necessary research and development (R ampersand D) activities required to reach demonstration and commercialization. Second generation power plant designs, employing molten-salt and volumetric-air receivers, were assessed at the size of 30 and 100 MWe. The study developed a common guideline and used data from previous system tests and studies. The levelized-energy costs for the second generation plants were estimated and found to be competitive with costs from fossil-fueled power plants. Potential for further cost reductions exists if technical improvements can be introduced successfully in the long term. Additionally, the study presents results of plant reliability and uncertainty analyses. Mid- and long-term technical potentials are described, as well as recommendations for the R ampersand D activities needed to reach the goal of large-scale commercialization. The results of this study have already helped direct research in the US and Europe. For example, the favorable potential for these technologies has led to the Solar Two molten-salt project in the US and the TSA volumetric receiver test in Spain. In addition, early analysis conducted within this study indicated that an advanced thermal storage medium was necessary to achieve favorable economics for the air plant. This led to the design of the thermal storage system currently being tested in Spain. In summary, each of the investigated receiver technologies has mid- and long-term potential for improving plant performance and reducing capital and energy costs (resulting in less than 10 cts/kWh given excellent insolation conditions) in an environmentally safe way and largely independent of fossil-fuel prices

  19. Research

    African Journals Online (AJOL)

    A descriptive qualitative research design was used to determine whether participants ... simulation as a teaching method; a manikin offering effective learning; confidence ..... Tesch R. Qualitative Research: Analysis Types and Software Tools.

  20. Research

    African Journals Online (AJOL)

    research process, as part of which students must find and appraise evidence from research.[5] This highlights that teaching research methodology is inclined towards equipping students ... Students believed that evidence-based practice was vital, yet their understanding of the concept was restricted when compared with the.

  1. Additional supply agreement of 9 December 1988 between the International Atomic Energy Agency and the Governments of the Islamic Republic of Iran and of Argentina for the transfer of enriched uranium for a research reactor in Iran

    International Nuclear Information System (INIS)

    1990-01-01

    The document reproduces the text of the additional supply agreement of 9 December 1988 between the IAEA and the Government of the Islamic Republic of Iran and of Argentina for the transfer of 115.80 kilograms of uranium enriched up to 20% in the isotope uranium-235 for a research reactor in Iran

  2. Research

    African Journals Online (AJOL)

    abp

    Key words: Complications respiratoires postopératoires, chirurgie de l'aorte, facteurs de risque. Received: ... le profil épidémiologique et déterminer les facteurs de risque des complications respiratoires dans notre contexte Méthodes: Il s'agit d'une étude de cohorte .... (IDM) répondait à la définition universelle de 2007 [6].

  3. Solar advanced internal film receiver

    International Nuclear Information System (INIS)

    Torre Cabezas, M. de la

    1990-01-01

    In a Solar Central Internal Film Receiver, the heat absorbing fluid (a molten nitrate salt) flows in a thin film down over the non illuminated side of an absorber panel. Since the molten salt working fluid is not contained in complicated tube manifolds, the receiver design is simples than a conventional tube type-receiver resulting in a lower cost and a more reliable receiver. The Internal Film Receiver can be considered as an alternative to the Direct Absorption Receiver, in the event that the current problems of the last one can not be solved. It also describes here the test facility which will be used for its solar test, and the test plans foreseen. (Author) 17 refs

  4. Communications receivers principles and design

    CERN Document Server

    Rohde, Ulrich L; Zahnd, Hans

    2017-01-01

    This thoroughly updated guide offers comprehensive explanations of the science behind today’s radio receivers along with practical guidance on designing, constructing, and maintaining real-world communications systems. You will explore system planning, antennas and antenna coupling, amplifiers and gain control, filters, mixers, demodulation, digital communication, and the latest software defined radio (SDR) technology. Written by a team of telecommunication experts, Communications Receivers: Principles and Design, Fourth Edition, features technical illustrations, schematic diagrams, and detailed examples. Coverage includes: • Basic radio considerations • Radio receiver characteristics • Receiver system planning • Receiver implementation considerations • RF and baseband techniques for Software-Defined Radios • Transceiver SDR considerations • Antennas and antenna coupling • Mixers • Frequency sources and control • Ancillary receiver circuits • Performance measurement

  5. Good practices according to WHO’s recommendation for normal labor and birth and women’s assessment of the care received: the “birth in Brazil” national research study, 2011/2012

    Directory of Open Access Journals (Sweden)

    Marcia Leonardi Baldisserotto

    2016-10-01

    Full Text Available Abstract Background The World Health Organization recommends good practices for the conduct of uncomplicated labor and birth, with the aim of improving the quality of and assessment by women of childbirth care. The aim of this study was to evaluate the association between adoption of good practices according to WHO’s recommendation for normal labor and birth and assessment by women of the care received. Methods Birth in Brazil is a national hospital-based study with countrywide representation consisting of 23,894 mothers and their newborns, conducted between February 2011 and October 2012. The present study analysed a subsample of this national survey. Postpartum women classified as low risk during pregnancy who had experienced either spontaneous or induced labor were included in this study, totalling 4102 mothers. To estimate the association between assessment by women of the childbirth care received (dependent variable and good practices according to WHO’s recommendation during normal labor and birth (independent variables, a multinomial logistic regression analysis was used and crude and adjusted odds ratios calculated with their 95 % confidence intervals. Results The good practices associated with positive assessment of the care received by women during labor and birth included the partner’s presence, privacy in the birthing place, time available to ask questions, clarity of information received, and empathic support from caregivers during labor and birth. Freedom of movement, free nutrition offered, choice of companions, nonpharmacological analgesia, skin-to-skin contact and breastfeeding in the childbirth room were not associated with the assessment by women of the care received. Conclusions Our findings reveal the importance to mothers of their relationship with the team of caregivers during labor and birth. Therefore, caregiver teams must be qualified within a more humanistic vision of childbirth health care.

  6. Analog fourier transform channelizer and OFDM receiver

    OpenAIRE

    2007-01-01

    An OFDM receiver having an analog multiplier based I-Q channelizing filter, samples and holds consecutive analog I-Q samples of an I-Q baseband, the I-Q basebands having OFDM sub-channels. A lattice of analog I-Q multipliers and analog I-Q summers concurrently receives the held analog I-Q samples, performs analog I-Q multiplications and analog I-Q additions to concurrently generate a plurality of analog I-Q output signals, representing an N-point discrete Fourier transform of the held analog ...

  7. Research

    African Journals Online (AJOL)

    abp

    2015-03-06

    Mar 6, 2015 ... Introduction: Several studies in Sub- Saharan Africa have documented high and ... Methods: A Descriptive cross sectional survey was employed and three hundred twenty ... In addition, unwanted pregnancy among female.

  8. Research

    African Journals Online (AJOL)

    raoul

    2011-08-25

    Aug 25, 2011 ... other African nations lack published animal welfare laws. .... The internationally accepted three Rs framework (Reduction, ... In addition, the lack of institutional animal ethics committees promotes the outsourcing of animal.

  9. Research

    African Journals Online (AJOL)

    abp

    2013-10-19

    Oct 19, 2013 ... Although women with breast cancer get clinical management, there is need to design holistic palliative ... women in addition to Kaposi's sarcoma and cervical cancer [1,2]. The incidence of ..... Asian Indian women: Knowledge ...

  10. Stability of heterodyne terahertz receivers

    NARCIS (Netherlands)

    Kooi, J.W.; Baselmans, J.J.A.; Baryshev, A.; Schieder, R.; Hajenius, M.; Gao, J.R.; Klapwijk, T.M.; Voronov, B.; Gol'tsman, G.

    2006-01-01

    In this paper we discuss the stability of heterodyne terahertz receivers based on small volume NbN phonon cooled hot electron bolometers (HEBs). The stability of these receivers can be broken down in two parts: the intrinsic stability of the HEB mixer and the stability of the local oscillator (LO)

  11. Research

    African Journals Online (AJOL)

    2014-05-06

    May 6, 2014 ... facilitate and support articulation between the ECT mid-level worker qualification and the professional B EMC degree. Methods. The researchers used an exploratory, sequential mixed-method design, which is characterised by a qualitative phase of research followed by a quantitative phase. This design is ...

  12. Research

    African Journals Online (AJOL)

    supports medical education and research at institutions in 12 ... (CBE). CapacityPlus, led by IntraHealth International, is the USAID-funded ... acquire public health, clinical, and/or research skills, usually through applied learning in a .... If students were evaluated, indicate the type of student (i.e. medical, dental, nursing, etc.) ...

  13. Research

    African Journals Online (AJOL)

    abp

    2017-01-24

    Jan 24, 2017 ... and the specific rotavirus VP4 (P-types) and VP7 (G-types) determined. Results: The .... Centre for Virus Research (CVR) of the Kenya Medical Research. Institute (KEMRI) ... rotavirus dsRNA was run on 10% polyacrylamide resolving gels using a large format .... What is known about this topic. •. Rotavirus is ...

  14. Breastfeeding peer support: are there additional benefits?

    Science.gov (United States)

    Wade, Deborah; Haining, Shona; Day, Ann

    2009-12-01

    Anecdotal discussion among breastfeeding peer supporters and the infant-feeding co-ordinator suggested that breastfeeding peer support provided by breastfeeding peer supporters may offer benefits to breastfeeding women and their families other than increasing breastfeeding initiation and sustainability. The aim of this research was to determine whether there was evidence to support this. The research team used focus groups to obtain information from 16 local women who had received breastfeeding peer support from breastfeeding peer supporters. The key themes that emerged were--improved mental health, increased self-esteem or confidence, parenting skills, improved family diet, breastfeeding sustainability and poor hospital experience.The findings suggest that breastfeeding peer supporters supporting mothers to breastfeed, with the intention of increasing both breastfeeding rates and sustainability, may have additional benefits in several aspects of families' lives. Breastfeeding peer support may play an important role in helping to attain targets such as reducing obesity and postnatal depression.

  15. UWB delay and multiply receiver

    Energy Technology Data Exchange (ETDEWEB)

    Dallum, Gregory E.; Pratt, Garth C.; Haugen, Peter C.; Romero, Carlos E.

    2013-09-10

    An ultra-wideband (UWB) delay and multiply receiver is formed of a receive antenna; a variable gain attenuator connected to the receive antenna; a signal splitter connected to the variable gain attenuator; a multiplier having one input connected to an undelayed signal from the signal splitter and another input connected to a delayed signal from the signal splitter, the delay between the splitter signals being equal to the spacing between pulses from a transmitter whose pulses are being received by the receive antenna; a peak detection circuit connected to the output of the multiplier and connected to the variable gain attenuator to control the variable gain attenuator to maintain a constant amplitude output from the multiplier; and a digital output circuit connected to the output of the multiplier.

  16. Customizable Digital Receivers for Radar

    Science.gov (United States)

    Moller, Delwyn; Heavey, Brandon; Sadowy, Gregory

    2008-01-01

    Compact, highly customizable digital receivers are being developed for the system described in 'Radar Interferometer for Topographic Mapping of Glaciers and Ice Sheets' (NPO-43962), NASA Tech Briefs, Vol. 31, No. 7 (August 2007), page 72. The receivers are required to operate in unison, sampling radar returns received by the antenna elements in a digital beam-forming (DBF) mode. The design of these receivers could also be adapted to commercial radar systems. At the time of reporting the information for this article, there were no commercially available digital receivers capable of satisfying all of the operational requirements and compact enough to be mounted directly on the antenna elements. A provided figure depicts the overall system of which the digital receivers are parts. Each digital receiver includes an analog-to-digital converter (ADC), a demultiplexer (DMUX), and a field-programmable gate array (FPGA). The ADC effects 10-bit band-pass sampling of input signals having frequencies up to 3.5 GHz. The input samples are demultiplexed at a user-selectable rate of 1:2 or 1:4, then buffered in part of the FPGA that functions as a first-in/first-out (FIFO) memory. Another part of the FPGA serves as a controller for the ADC, DMUX, and FIFO memory and as an interface between (1) the rest of the receiver and (2) a front-panel data port (FPDP) bus, which is an industry-standard parallel data bus that has a high data-rate capability and multichannel configuration suitable for DBF. Still other parts of the FPGA in each receiver perform signal-processing functions. The digital receivers can be configured to operate in a stand-alone mode, or in a multichannel mode as needed for DBF. The customizability of the receiver makes it applicable to a broad range of system architectures. The capability for operation of receivers in either a stand-alone or a DBF mode enables the use of the receivers in an unprecedentedly wide variety of radar systems.

  17. Measuring Balance Across Multiple Radar Receiver Channels.

    Energy Technology Data Exchange (ETDEWEB)

    Doerry, Armin W.; Bickel, Douglas L.

    2018-03-01

    When radar receivers employ multiple channels, the general intent is for the receive channels to be as alike as possible, if not as ideal as possible. This is usually done via prudent hardware design, supplemented by system calibration. Towards this end, we require a quality metric for ascertaining the goodness of a radar channel, and the degree of match to sibling channels. We propose a relevant and useable metric to do just that. Acknowledgements This report was the result of an unfunded research and development activity.

  18. Research

    African Journals Online (AJOL)

    abp

    2017-10-25

    Oct 25, 2017 ... stigma and superstition are known to lead to frequent presentation .... The limited documented research on challenges to help-seeking behaviour for cancer ..... to touch your breast [16] that breast self-examination may cause.

  19. Research

    African Journals Online (AJOL)

    abp

    2016-07-12

    Jul 12, 2016 ... multiple risk factors provides support for multiple-behavior interventions as ... consumption) with smoking therefore needs further research. As such this study .... restaurants, in bars, and on a statewide basis. They preferred to.

  20. Research

    African Journals Online (AJOL)

    The mini-clinical-evaluation exercise (mini-CEX) is a way of assessing the clinical ... Ethical approval for this study was obtained from the Medical Health. Research ..... mini-CEX assessment and feedback session, the greater the likelihood of.

  1. Research

    African Journals Online (AJOL)

    abp

    2016-04-14

    Apr 14, 2016 ... Qualitative data, content analysis approach was used. Results: Overall 422 .... Study design: A mixed method cross-sectional design using both quantitative and qualitative research methods as described by. Hanson et al [33] ...

  2. Research

    International Nuclear Information System (INIS)

    1999-01-01

    Subjects covered in this section are: (1) PCAST panel promotes energy research cooperation; (2) Letter issued by ANS urges funding balance in FFTF restart consideration and (3) FESAC panel releases report on priorities and balance

  3. Research

    African Journals Online (AJOL)

    Research. December 2017, Vol. 9, No. 4 AJHPE 171. During curriculum development, teachers ... Ideally, examiners need an educational method to determine ..... A major focus of this study was addressing the human resource gap when.

  4. Review and future perspective of central receiver design and performance

    Science.gov (United States)

    Zhu, Guangdong; Libby, Cara

    2017-06-01

    Concentrating solar power (CSP) technology provides a commercial solar option to the utility-scale electricity market. CSP is unique in its ability to include low-cost thermal storage; thus, it can generate electricity when the sun is not available and dispatch electricity to meet varying load requirements. Within the suite of CSP technologies, the central receiver design represents the state-of-the-art technology, promising low cost, high performance, and dispatchable energy production. Current total capacity of central receiver plants worldwide is about 1.0 gigawatt (electric) with operating plants in Spain and the United States, as well as projects under construction in Asia, the Middle East, and North Africa. Central receiver technology has been under development since the 1950s, and a variety of central receiver designs have been explored. A distinguishing feature is the heat transfer medium. Central receiver designs exist that use dense fluids, gases, and solid particles in this role. Water/steam and molten salt receivers have been adopted in current commercial plants and are often coupled with a steam-Rankine power cycle with an operating temperature of less than 600°C. Many new central receiver concepts, such as the volumetric air, supercritical carbon dioxide (sCO2), solid particle, and liquid-metal receiver designs, are under active research and development (R&D). New designs target operating temperatures generally higher than 700°C-800°C—and even above 1000°C—so that higher-performance power cycles such as the sCO2-Brayton cycle or air-Brayton/steam-Rankine combined cycle can be used to promote greater overall system efficiency. Central receiver thermal storage provides dispatchability unavailable from variable-output renewables such as solar photovoltaic and wind power. Case study analysis of the California grid shows that there is a limit on the amount of non-dispatchable renewable generation that the grid can accommodate, beyond which

  5. Review and Future Perspective of Central Receiver Design and Performance

    Energy Technology Data Exchange (ETDEWEB)

    Zhu, Guangdong; Libby, Cara

    2017-06-27

    Concentrating solar power (CSP) technology provides a commercial solar option to the utility-scale electricity market. CSP is unique in its ability to include low-cost thermal storage; thus, it can generate electricity when the sun is not available and dispatch electricity to meet varying load requirements. Within the suite of CSP technologies, the central receiver design represents the state-of-the-art technology, promising low cost, high performance, and dispatchable energy production. Current total capacity of central receiver plants worldwide is about 1.0 gigawatt (electric) with operating plants in Spain and the United States, as well as projects under construction in Asia, the Middle East, and North Africa. Central receiver technology has been under development since the 1950s, and a variety of central receiver designs have been explored. A distinguishing feature is the heat transfer medium. Central receiver designs exist that use dense fluids, gases, and solid particles in this role. Water/steam and molten salt receivers have been adopted in current commercial plants and are often coupled with a steam-Rankine power cycle with an operating temperature of less than 600 degrees C. Many new central receiver concepts, such as the volumetric air, supercritical carbon dioxide (sCO2), solid particle, and liquid-metal receiver designs, are under active research and development (R&D). New designs target operating temperatures generally higher than 700 degrees C-800 degrees C -- and even above 1000 degrees C -- so that higher-performance power cycles such as the sCO2-Brayton cycle or air-Brayton/steam-Rankine combined cycle can be used to promote greater overall system efficiency. Central receiver thermal storage provides dispatchability unavailable from variable-output renewables such as solar photovoltaic and wind power. Case study analysis of the California grid shows that there is a limit on the amount of non-dispatchable renewable generation that the grid can

  6. Dish/stirling hybrid-receiver

    Science.gov (United States)

    Mehos, Mark S.; Anselmo, Kenneth M.; Moreno, James B.; Andraka, Charles E.; Rawlinson, K. Scott; Corey, John; Bohn, Mark S.

    2002-01-01

    A hybrid high-temperature solar receiver is provided which comprises a solar heat-pipe-receiver including a front dome having a solar absorber surface for receiving concentrated solar energy, a heat pipe wick, a rear dome, a sidewall joining the front and the rear dome, and a vapor and a return liquid tube connecting to an engine, and a fossil fuel fired combustion system in radial integration with the sidewall for simultaneous operation with the solar heat pipe receiver, the combustion system comprising an air and fuel pre-mixer, an outer cooling jacket for tangentially introducing and cooling the mixture, a recuperator for preheating the mixture, a burner plenum having an inner and an outer wall, a porous cylindrical metal matrix burner firing radially inward facing a sodium vapor sink, the mixture ignited downstream of the matrix forming combustion products, an exhaust plenum, a fossil-fuel heat-input surface having an outer surface covered with a pin-fin array, the combustion products flowing through the array to give up additional heat to the receiver, and an inner surface covered with an extension of the heat-pipe wick, a pin-fin shroud sealed to the burner and exhaust plenums, an end seal, a flue-gas diversion tube and a flue-gas valve for use at off-design conditions to limit the temperature of the pre-heated air and fuel mixture, preventing pre-ignition.

  7. Research

    African Journals Online (AJOL)

    abp

    2016-07-20

    Jul 20, 2016 ... Abstract. Introduction: In sub Saharan Africa, childbirth remains a challenge that creates the need for additional screening tools. Maternal pelvis height, which is currently in use by automotive engineers has previously been shown to have significant associations with various childbirth related outcomes and ...

  8. Research

    African Journals Online (AJOL)

    ebutamanya

    2015-12-16

    Dec 16, 2015 ... ... motivation among health workers (62%), overwhelming workload (89%) and abuse of services by clients ... which permits unrestricted use, distribution, and reproduction in any medium, provided the ..... additional drugs and other supplies [12]. .... disruptive effects of user fee exemption policies on health.

  9. Research

    African Journals Online (AJOL)

    abp

    2017-12-15

    Dec 15, 2017 ... also to the food industry, which should also consider sugar content reduction in ... shouldn't be affected by high amount of sugar or use of artificial ingredients .... have yoghurt without additives and less sweet. On the other ...

  10. Research

    African Journals Online (AJOL)

    2018-03-26

    Mar 26, 2018 ... developing countries, they affect low- and middle-income countries. (LMICs) ... smoking and lack of physical activity.[2,3] Such ... Healthcare empowerment is key to the prevention of diabetes[15,16] and should be ..... word-search game and a health model to explain healthy lifestyle choices, in addition to ...

  11. Research

    African Journals Online (AJOL)

    abp

    2014-03-28

    Mar 28, 2014 ... 1Department of Paediatrics and Child Health, Kilimanjaro Christian Medical University College, P. O. Box 2240, Moshi, Tanzania, 2KCMC- Duke. Collaboration, P.O Box .... providing additional food to children taking medication. Of these, ... should be used because they complement each other. Surprisingly ...

  12. Research

    African Journals Online (AJOL)

    raoul

    2011-08-03

    Aug 3, 2011 ... The potential predictor variables included socio-demographic characteristics of the mother; indices for decision-making power about health and nutrition as well as decision-making power about short and long term investment strategies, housing material, household assets; in addition to household size ...

  13. Britain's delegation to CERN, the European Centre for Nuclear Research near Geneva, voted in favour of a project which take seven years to build, involve a 27 kilometre long tunnel, and cost 230 million pounds. Now LEP receives the go-ahead later this month

    CERN Multimedia

    Llewellyn Smith, Christopher Hubert

    1981-01-01

    Britain's delegation to CERN, the European Centre for Nuclear Research near Geneva, voted in favour of a project which take seven years to build, involve a 27 kilometre long tunnel, and cost 230 million pounds. Now LEP receives the go-ahead later this month

  14. The ARSQ: the athletes' received support questionnaire.

    Science.gov (United States)

    Freeman, Paul; Coffee, Pete; Moll, Tjerk; Rees, Tim; Sammy, Nadine

    2014-04-01

    To address calls for context-specific measurement of social support, this article reports the development of the Athletes' Received Support Questionnaire (ARSQ) and demonstrates initial evidence for its validity. Across four studies there was support for a four-dimensional structure reflecting emotional, esteem, informational, and tangible received support. There was also support for unidimensional and higher-order models. Further, Study 3 provided some support for convergent validity, with significant correlations between the corresponding dimensions of the ARSQ and the Inventory of Socially Supportive Behaviors. Study 4 provided evidence for the nomological validity of the ARSQ. Emotional and esteem support significantly predicted self-confidence and positive affect, and tangible support significantly moderated the relationship between stress and negative affect. Collectively, these results provide initial evidence for the validity of the ARSQ, and offer researchers flexibility to adopt either a multidimensional or aggregated approach to measuring received support.

  15. 77 FR 13009 - Regulation of Fuels and Fuel Additives: Identification of Additional Qualifying Renewable Fuel...

    Science.gov (United States)

    2012-03-05

    ... Regulation of Fuels and Fuel Additives: Identification of Additional Qualifying Renewable Fuel Pathways Under the Renewable Fuel Standard Program AGENCY: Environmental Protection Agency (EPA). ACTION: Withdrawal... Renewable Fuel Standard program regulations. Because EPA received adverse comment, we are withdrawing the...

  16. Research

    African Journals Online (AJOL)

    abp

    2017-05-18

    May 18, 2017 ... available to populations of developing countries [2-5]. In 2013, in. Western and Central Europe and ..... initiation among the infected persons in the community. Addressing stigma and educating ... Lifespan/Tufts/Brown Center for AIDS Research (P30AI042853). Tables. Table 1: Baseline characteristics of ...

  17. Research

    African Journals Online (AJOL)

    abp

    15 févr. 2016 ... présentent un Indice de Masse Corporel (IMC) normal, les autres femmes sont soit ..... In The health belief model and personal health behavior, edited by MH ... Evaluation of the Osteoporosis Health Belief Scale. Research in.

  18. Research

    African Journals Online (AJOL)

    2017-03-14

    Mar 14, 2017 ... R Ebrahim,1 MSc (Dent); H Julie,2 MPH, MCur, PhD. 1 Extended ... and research is applied to develop and sustain society.[5]. Methods .... service they want, not the service we want to give whether they want it or. Co math. G.

  19. Research

    African Journals Online (AJOL)

    abp

    2017-11-24

    Nov 24, 2017 ... Page number not for citation purposes. 1. Prevalence and determinants of common mental ..... illnesses were smoke cigarette in the last 3 months that make prevalence of tobacco use 38.2%. ..... Okasha A, Karam E.Mental health services and research in the. Arab world. Acta Psychiatrica Scandinavica.

  20. Research

    African Journals Online (AJOL)

    abp

    2014-04-21

    Apr 21, 2014 ... Prospective assessment of the risk of obstructive sleep apnea in ... Faculty of Clinical Sciences, College of Medicine, University of .... University Teaching Hospital Health Research Ethics Committee ... BANG, Berlin questionnaire and the American Society of .... The epidemiology of adult obstructive sleep.

  1. Research

    African Journals Online (AJOL)

    abp

    2016-02-01

    Feb 1, 2016 ... University Hospital, DK-5000 Odense, Denmark, 3Center for Global Health, Institute of Clinical Research, University of Southern Denmark, DK-5000. Odense .... BHP is a Danish-Guinean Demographic Surveillance Site with a study-area .... variables such as age groups, previous military duty, history of.

  2. Research

    African Journals Online (AJOL)

    abp

    2015-06-24

    Jun 24, 2015 ... related immunosuppression, previous history of TB, and pause in treatment [6]. In Brazil, researchers .... treatment, use of traditional medicines or herbs, history of TB drug side effects and treatment delay). ..... therapy for pulmonary tuberculosis in Lima Ciudad, Peru. International journal of tuberculosis and ...

  3. Research

    African Journals Online (AJOL)

    Research. May 2016, Vol. 8, No. 1 AJHPE 37. Students who enrol in occupational therapy (OT) at the. University of Kwa Zulu-Natal (UKZN), Durban, South Africa ... The latter may include becoming familiar with the disintegrating social systems in primary .... They also lacked the skills needed to adapt sessions and failed to ...

  4. Research

    African Journals Online (AJOL)

    ebutamanya

    2015-06-22

    Jun 22, 2015 ... collaboration with Makerere University, School of Public Health. We acknowledge The Family Health Research and Development Centre. (FHRDC) Uganda. Supported by Bill & Melinda Gates Institute for. Population & Reproductive Health, Johns Hopkins Bloomberg School of Public Health, Baltimore, ...

  5. Research

    African Journals Online (AJOL)

    However, a focus on competence alone is inadequate to produce graduates who are capable of adapting to the changing needs of health systems. While knowledge and technical ... shared their responses to guided questions. There were three sessions; after each session the researcher aggregated participant responses ...

  6. Research

    African Journals Online (AJOL)

    abp

    2014-01-31

    Jan 31, 2014 ... by Hazarika in a population-based study in India. The researcher noted that patients' preference to the private health facilities was due mainly to their dissatisfaction with the services in the public health facilities [11]. Furthermore, the quality of the services in the private health facilities could also be a major ...

  7. Research

    African Journals Online (AJOL)

    2018-03-20

    Mar 20, 2018 ... student health professionals in various institutions, both in South Africa. (SA) and internationally. ... field include dentists, dental therapists and oral hygienists in training, .... The College of Health Sciences at UKZN has four schools: clinical ..... Journal of Emerging Trends in Educational Research and Policy ...

  8. Research

    African Journals Online (AJOL)

    abp

    2017-09-14

    Sep 14, 2017 ... Abstract. Introduction: Medical and dental students are a high-risk group for hepatitis B virus (HBV) infection which is an ... The Pan African Medical Journal - ISSN 1937-8688. ... Research ... in the College of Health Sciences and clinical students (years four to .... Hepatology International.2017 Jan; 11(1):.

  9. Research

    African Journals Online (AJOL)

    abp

    2015-01-19

    Jan 19, 2015 ... One research assistant was available to assist the learners and to answer questions while they completed the questionnaires during a classroom period. ..... PubMed | Google Scholar. 4. Hall PA, Holmqvist M, Sherry SB. Risky adolescent sexual behaviour: A psychological perspective for primary care.

  10. The Analysis of Liquidity and Receivables as a Component of Corporate Financial Management

    Directory of Open Access Journals (Sweden)

    Feshchenko Oleh Р.

    2017-08-01

    Full Text Available The article is aimed at the analysis of liquidity and receivables of corporations and substantiation of proposals as to its improvement as part of the management of financial status of companies. The instruments, methodical techniques, tasks, and stages of managing the accounts receivable were generalized. It has been substantiated that, at the current stage of development of Ukraine’s economy, it appears not sufficient to apply the coefficient analysis only, there is a need to supplement it by the regression analysis of the panel data, allowing for the temporal and spatial characteristics of the sample. The development of additional indicators for the monitoring of receivables can be suggested as recommendations for the studied corporations in order to reduce future risks of non-recovery and financial deterioration. Prospect for further research is an in-depth regression analysis of the panel data in terms of the measures to refinance receivables and the financial dynamics of companies.

  11. GIVING AND RECEIVING CONSTRUCTIVE FEEDBACK

    Directory of Open Access Journals (Sweden)

    Ірина Олійник

    2015-05-01

    Full Text Available The article scrutinizes the notion of feedback applicable in classrooms where team teaching is provided. The experience of giving and receiving feedback has been a good practice in cooperation between a U.S. Peace Corps volunteer and a Ukrainian counterpart. Giving and receiving feedback is an effective means of classroom observation that provides better insight into the process of teaching a foreign language. The article discusses the stages of feedback and explicates the notion of sharing experience between two teachers working simultaneously in the same classroom. The guidelines for giving and receiving feedback have been provided as well as the most commonly used vocabulary items have been listed. It has been proved that mutual feedback leads to improving teaching methods and using various teaching styles and techniques.

  12. Receiver-exciter controller design

    Science.gov (United States)

    Jansma, P. A.

    1982-01-01

    A description of the general design of both the block 3 and block 4 receiver-exciter controllers for the Deep Space Network (DSN) Mark IV-A System is presented along with the design approach. The controllers are designed to enable the receiver-exciter subsystem (RCV) to be configured, calibrated, initialized and operated from a central location via high level instructions. The RECs are designed to be operated under the control of the DMC subsystem. The instructions are in the form of standard subsystem blocks (SSBs) received via the local area network (LAN). The centralized control provided by RECs and other DSCC controllers in Mark IV-A is intended to reduce DSN operations costs from the Mark III era.

  13. Stability of heterodyne terahertz receivers

    OpenAIRE

    Kooi, J. W.; Baselmans, J. J. A.; Baryshev, A.; Schieder, R.; Hajenius, M.; Gao, J. R.; Klapwijk, T. M.; Voronov, B.; Gol'tsman, G.

    2006-01-01

    In this paper we discuss the stability of heterodyne terahertz receivers based on small volume NbN phonon cooled hot electron bolometers (HEBs). The stability of these receivers can be broken down in two parts: the intrinsic stability of the HEB mixer and the stability of the local oscillator (LO) signal injection scheme. Measurements show that the HEB mixer stability is limited by gain fluctuations with a 1/f spectral distribution. In a 60 MHz noise bandwidth this results in an Allan varian...

  14. BWR zinc addition Sourcebook

    International Nuclear Information System (INIS)

    Garcia, Susan E.; Giannelli, Joseph F.; Jarvis, Alfred J.

    2014-01-01

    Boiling Water Reactors (BWRs) have been injecting zinc into the primary coolant via the reactor feedwater system for over 25 years for the purpose of controlling primary system radiation fields. The BWR zinc injection process has evolved since the initial application at the Hope Creek Nuclear Station in 1986. Key transitions were from the original natural zinc oxide (NZO) to depleted zinc oxide (DZO), and from active zinc injection of a powdered zinc oxide slurry (pumped systems) to passive injection systems (zinc pellet beds). Zinc addition has continued through various chemistry regimes changes, from normal water chemistry (NWC) to hydrogen water chemistry (HWC) and HWC with noble metals (NobleChem™) for mitigation of intergranular stress corrosion cracking (IGSCC) of reactor internals and primary system piping. While past reports published by the Electric Power Research Institute (EPRI) document specific industry experience related to these topics, the Zinc Sourcebook was prepared to consolidate all of the experience gained over the past 25 years. The Zinc Sourcebook will benefit experienced BWR Chemistry, Operations, Radiation Protection and Engineering personnel as well as new people entering the nuclear power industry. While all North American BWRs implement feedwater zinc injection, a number of other BWRs do not inject zinc. This Sourcebook will also be a valuable resource to plants considering the benefits of zinc addition process implementation, and to gain insights on industry experience related to zinc process control and best practices. This paper presents some of the highlights from the Sourcebook. (author)

  15. 锂离子电池电解液负极成膜添加剂的研究进展%Research progress of negative film-forming additives in electrolyte for Li-ion batteries

    Institute of Scientific and Technical Information of China (English)

    周丹; 梁风; 姚耀春

    2016-01-01

    Forming a stable solid electrolyte interface film (SEI film) is the key to solve the compatibility between lithium ion battery electrode material and electrolyte. Therefore,the research of high quality anode film-forming additive in electrolyte for lithium ion battery attracts much attention. The principle of film-forming additives for organic electrolyte in Li-ion batteries was reviewed. The research status of a variety of additives was particularly introduced. The recent progress on negative film-forming additives was reviewed in detail,from the perspectives of film formation mechanisms and quantum calculation. The main problem was how to select more suitable and efficient film-forming additives. In addition,the possible trends in this area were proposed:①Understanding the mechanism of additive reacting with the electrolyte,especially for the negative film forming additive which has minimum side effects for lithium ion battery;②Combining two or more additives together to compensate the deficiencies of one additive;③Increasing the solubility of inorganic film-forming additives in the electrolyte.%解决锂离子电池电极材料和电解液相容性的关键是形成稳定且Li+可导的固态电解质界面膜(SEI膜),因此,对优质负极成膜添加剂的研究成为锂离子电池研发中的一个热点。本文综述了锂离子电池电解液成膜添加剂的作用原理,具体介绍了各类负极成膜添加剂的研究现状,从成膜反应机理和理论计算方面详述了近几年来负极成膜添加剂的研究进展。分析了所存在的问题主要是如何快速地挑选出更适宜、更高效的成膜添加剂,并指出了成膜添加剂未来的发展趋势为:①研究各添加剂与电解液的反应机理,着重开发对锂离子电池副反应小的负极成膜添加剂;②通过选择两种或两种以上的添加剂的协同作用,以弥补一种添加剂的不足;③提高无机成膜添加剂在电解液中的溶解度。

  16. Valuation of Residential Premises for the Purposes of Securing the Receivables of the Creditor in Poland

    Science.gov (United States)

    Hełdak, Maria; Stacherzak, Agnieszka

    2017-10-01

    The study presents an analysis of the theoretical and practical issues connected with securing the receivables of creditors, in particular the principles connected with the appraisal of real property value used for the purposes of granting loans in Poland. The scope of research included the basic elements of the functioning and organisation of the Polish banking system, legal forms of securing debt receivables and the principles of real property valuation for universal and mortgage banks. Additionally, the authors have conducted an analysis of the number and amount of loans granted in Poland in the years 2009 - 2016

  17. Receiving Assistance and Local Food System Participation

    Directory of Open Access Journals (Sweden)

    Rebecca L. Som Castellano

    2017-02-01

    Full Text Available A body of literature has noted that local food systems (LFSs may not involve active participation by individuals with lower incomes. This is, in part, a function of racial and class hegemony, as well as physical and financial accessibility of LFSs. LFS institutions, such as farmers’ markets, have been working to facilitate receipt of food assistance programs, such as the Supplemental Nutrition Assistance Program (SNAP. Charitable assistance programs, such as food banks, have also been actively working to engage in LFSs, for example, by making local foods available. However, little research has explored the role that receiving public or charitable assistance can play in influencing LFS participation. In this article, I utilize quantitative and qualitative data collected from across the state of Ohio to examine the relationship between receiving assistance and LFS participation for women, who remain predominately responsible for food provisioning in the U.S., including among those who participate in LFSs. Quantitative results suggest that receiving assistance can increase participation in LFSs. Qualitative data provides more nuanced information about the importance of food assistance for women who want to participate in LFSs, and suggest that it is essential that food cooperatives and farmers’ markets are equipped to receive food assistance programs, such as SNAP, in order for women with lower incomes to participate in LFSs.

  18. Transfer of Training in Simple Addition.

    Science.gov (United States)

    Chen, Yalin; Campbell, Jamie I D

    2017-04-18

    In recent years several researchers have proposed that skilled adults may solve single-digit addition problems (e.g. 3 + 1 = 4, 4 + 3 = 7) using a fast counting procedure. Practicing a procedure, often leads to transfer of learning and faster performance of unpracticed items. Such transfer has been demonstrated using a counting-based alphabet arithmetic task (e.g., B + 4 = C D E F) that indicated robust generalization of practice (i.e., RT gains) when untrained transfer problems at test had been implicitly practiced (e.g., practice B + 3, test B + 2 or B + 1). Here we constructed analogous simple addition problems (practice 4 + 3, test 4 + 2 or 4 + 1). In each of three experiments (total n = 108) participants received six practice blocks followed by two test blocks of new problems to examine generalization effects. Practice of addition identity-rule problems (i.e., 0 + N = N) showed complete transfer of RT gains made during practice to unpracticed items at test. In contrast, the addition ties (2 + 2, 3 + 3, etc.) presented large RT costs for unpracticed problems at test, but sped up substantially in the second test block. This pattern is consistent with item-specific strengthening of associative memory. The critical items were small non-tie additions (sum ≤ 10) for which the test problems would be implicitly practiced if counting was employed during practice. In all three experiments (and collectively) there was no evidence of generalization for these items in the first test block, but there was robust speed up when the items were repeated in the second test block. Thus, there was no evidence of the generalization of practice that would be expected if counting procedures mediated our participants' performance on small non-tie addition problems.

  19. Parâmetros bioquímicos de equinos submetidos à simulação de prova de enduro recebendo dietas com adição de óleo de soja Biochemical parameters of horses submitted to an endurance simulation receiving diets with soybean oil addition

    Directory of Open Access Journals (Sweden)

    Roberta Ariboni Brandi

    2010-02-01

    Full Text Available Com o objetivo de verificar o efeito da adição de níveis crescentes de óleo no concentrado sobre a atividade plasmática das enzimas creatina quinase (CK, aspartato aminotransferase (AST e lactato desidrogenase (LDH como indicativo de metabolismo energético, foram fornecidas dietas experimentais compostas de cinco níveis de óleo (controle, 6, 12, 18 e 24% do concentrado. Utilizaram-se 20 equinos da raça Árabe, peso médio de 400 kg, submetidos a prova de enduro de 80 km em esteira rolante. O enduro foi dividido em quatro anéis de 20 km, com duração média de 1 hora e dez minutos. A adição de óleo e a distância percorrida tiveram efeitos sobre as variáveis AST, CK e LDH, que apresentaram as respectivas expressões: AST (7,045-0,2292x+0,007991x2+0,008517z- 0,0003282xz, CK (8,06-,07020x+0,05546x2-0,001262x3+0,01204z+0,0006207xz e LDH (6,624-0,3522x+0,03448x2-0,0008382x3+0,02401z-0,0007489xz . O óleo é uma importante e bem aproveitada fonte de energia para equinos em exercício, pois sua adição na dieta de animais submetidos a prova de enduro promoveu alteração metabólica que favorece a produção de energia. O metabolismo animal poupou suas reservas energéticas oriundas da glicose, favorecendo a utilização do óleo. A menor atividade plasmática das enzimas AST, CK e LDH com a adição de óleo nas dietas indica direcionamento do metabolismo energético para a β-oxidação. Como apresentam várias isoenzimas, as enzimas estudadas atuam amplamente no metabolismo energético, favorecendo a constante reposição de ATP ao longo do exercício.The objective of this study was to verify the effect of increasing soybean oil addition levels in the concentrate, on the enzymatic activity CK (Creatine Kinase, LDH (Lactate Dehydrogenase, AST (Astarte aminostrafase, as an indication of energetic metabolism. Compond experimental diets were given with five oil levels (control, 6, 12, 18 and 24% concentrate. Twenty Arabian equines

  20. Femtosecond Photon-Counting Receiver

    Science.gov (United States)

    Krainak, Michael A.; Rambo, Timothy M.; Yang, Guangning; Lu, Wei; Numata, Kenji

    2016-01-01

    An optical correlation receiver is described that provides ultra-precise distance and/or time/pulse-width measurements even for weak (single photons) and short (femtosecond) optical signals. A new type of optical correlation receiver uses a fourth-order (intensity) interferometer to provide micron distance measurements even for weak (single photons) and short (femtosecond) optical signals. The optical correlator uses a low-noise-integrating detector that can resolve photon number. The correlation (range as a function of path delay) is calculated from the variance of the photon number of the difference of the optical signals on the two detectors. Our preliminary proof-of principle data (using a short-pulse diode laser transmitter) demonstrates tens of microns precision.

  1. Scintillation-Hardened GPS Receiver

    Science.gov (United States)

    Stephens, Donald R.

    2015-01-01

    CommLargo, Inc., has developed a scintillation-hardened Global Positioning System (GPS) receiver that improves reliability for low-orbit missions and complies with NASA's Space Telecommunications Radio System (STRS) architecture standards. A software-defined radio (SDR) implementation allows a single hardware element to function as either a conventional radio or as a GPS receiver, providing backup and redundancy for platforms such as the International Space Station (ISS) and high-value remote sensing platforms. The innovation's flexible SDR implementation reduces cost, weight, and power requirements. Scintillation hardening improves mission reliability and variability. In Phase I, CommLargo refactored an open-source GPS software package with Kalman filter-based tracking loops to improve performance during scintillation and also demonstrated improved navigation during a geomagnetic storm. In Phase II, the company generated a new field-programmable gate array (FPGA)-based GPS waveform to demonstrate on NASA's Space Communication and Navigation (SCaN) test bed.

  2. CERN Press Office receives award from Euroscience

    CERN Multimedia

    2009-01-01

    The CERN Communication group has received an award for its efforts in communicating the LHC first beam to the media and the public. James Gillies, head of the Communication group was presented the AlphaGalileo Research Public Relations Award on Wednesday, 14 October during the Euroscience Media Award Ceremony in Hannover. "It’s great to receive this recognition," said Gillies. "Of course, we had great material to work with: the LHC is a fantastic story and one that is going to get even better. Angels, Demons and black holes also had their roles to play, but behind the media interest there’s been a lot of hard work by my team. This is for them." The CERN Communication group also works with communication professionals in all the CERN Member States and major physics labs around the world through the European Particle Physics Communication Network, and the InterAction collaboration. "Without them," says Gillies, &am...

  3. Compressed Sensing-Based Direct Conversion Receiver

    DEFF Research Database (Denmark)

    Pierzchlewski, Jacek; Arildsen, Thomas; Larsen, Torben

    2012-01-01

    Due to the continuously increasing computational power of modern data receivers it is possible to move more and more processing from the analog to the digital domain. This paper presents a compressed sensing approach to relaxing the analog filtering requirements prior to the ADCs in a direct......-converted radio signals. As shown in an experiment presented in the article, when the proposed method is used, it is possible to relax the requirements for the quadrature down-converter filters. A random sampling device and an additional digital signal processing module is the price to pay for these relaxed...

  4. List of documents received by the INDC Secretariat

    International Nuclear Information System (INIS)

    1987-09-01

    The Nuclear Data Section of the International Atomic Energy Agency receives documents originated by or for the International Nuclear Data Committee for distribution. This list includes all INDC documents received and distributed by the INDC Secretariat during the period January 1984 to March 1986. This list is produced directly from computer printout in two sorts: one ordered by accession number, and the other ordered by document number within each origin series (e.g. listing all INDC(SEC)-documents in one block). In addition to the INDC documents received by the INDC Secretariat for distribution, this document also lists the titles of reports received as single copies for information

  5. Personal monitoring and assessment of doses received by radiation workers

    International Nuclear Information System (INIS)

    Swindon, T.N.; Morris, N.D.

    1981-12-01

    The Personal Radiation Monitoring Service operated by the Australian Radiation Laboratory is outlined and the types of monitors used for assessment of doses received by radiation workers are described. The distribution of doses received by radiation workers in different occupational categories is determined. From these distributions, the average doses received have been assessed and the maximum likely additional increase in cancer deaths in Australia as a result of occupational exposure estimated. This increase is shown to be very small. There is, however, a considerable spread of doses received by individuals within occupational groups

  6. A Decentralized Receiver in Gaussian Interference

    Directory of Open Access Journals (Sweden)

    Christian D. Chapman

    2018-04-01

    Full Text Available Bounds are developed on the maximum communications rate between a transmitter and a fusion node aided by a cluster of distributed receivers with limited resources for cooperation, all in the presence of an additive Gaussian interferer. The receivers cannot communicate with one another and can only convey processed versions of their observations to the fusion center through a Local Array Network (LAN with limited total throughput. The effectiveness of each bound’s approach for mitigating a strong interferer is assessed over a wide range of channels. It is seen that, if resources are shared effectively, even a simple quantize-and-forward strategy can mitigate an interferer 20 dB stronger than the signal in a diverse range of spatially Ricean channels. Monte-Carlo experiments for the bounds reveal that, while achievable rates are stable when varying the receiver’s observed scattered-path to line-of-sight signal power, the receivers must adapt how they share resources in response to this change. The bounds analyzed are proven to be achievable and are seen to be tight with capacity when LAN resources are either ample or limited.

  7. Spiritual well-being and quality of life among Icelanders receiving palliative care: data from Icelandic pilot-testing of a provisional measure of spiritual well-being from the European Organisation for Research and Treatment of Cancer.

    Science.gov (United States)

    Asgeirsdottir, G H; Sigurdardottir, V; Gunnarsdottir, S; Sigurbjörnsson, E; Traustadottir, R; Kelly, E; Young, T; Vivat, B

    2017-03-01

    Palliative care focuses on improving quality of life (QoL). This study examined the feasibility of the Icelandic version of a provisional European Organisation for Research and Treatment of Cancer (EORTC) measure of spiritual well-being (SWB), and explored the relationship between SWB and QoL for palliative care patients in Iceland. Instruments from the EORTC were used: the provisional measure of SWB, which was undergoing pilot-testing in Iceland, and the EORTC QLQ C15-PAL. The correlation between scores was examined and descriptive statistics were used. Structured interviews explored feasibility. Thirty persons participated with average age 72 years. Belief in God or a higher power had the mean 3.33 on a 1-4 scale and the mean for overall SWB was 5.73 on a 1-7 scale. The mean score for global health/QoL was 59.4, physical functioning 48.5 and emotional functioning 78.9 on a 0-100 scale. Overall QoL was positively correlated with SWB showing r(30) = 0.386, P = 0.035. The participants found that answering the provisional EORTC QLQ-SWB prompted an emotional response and took the opportunity to discuss the subject. The provisional SWB measure was found relevant for the Icelandic context, and the study indicates that SWB and QoL are closely connected. © 2015 John Wiley & Sons Ltd.

  8. Communication received from South Africa

    International Nuclear Information System (INIS)

    1984-02-01

    The document reproduces the press release with a statement by Dr. J.W.L. de Villiers, Executive Chairman of the Atomic Energy Corporation of South Africa Limited, issued on 31 January 1984 and included in the letter received by the Director General of the IAEA from the Resident Representative of South Africa to the Agency on 31 January 1984. This statement refers to the transfer of nuclear material equipment and technology by South Africa to other countries and the Non-Proliferation Treaty

  9. Absorption Efficiency of Receiving Antennas

    DEFF Research Database (Denmark)

    Andersen, Jørgen Bach; Frandsen, Aksel

    2005-01-01

    A receiving antenna with a matched load will always scatter some power. This paper sets an upper and a lower bound on the absorption efficiency (absorbed power over sum of absorbed and scattered powers), which lies between 0 and 100% depending on the directivities of the antenna and scatter...... patterns. It can approach 100% as closely as desired, although in practice this may not be an attractive solution. An example with a small endfire array of dipoles shows an efficiency of 93%. Several examples of small conical horn antennas are also given, and they all have absorption efficiencies less than...

  10. Three scientists to receive presidential Enrico Fermi award

    CERN Multimedia

    2003-01-01

    "Secretary of Energy Spencer Abraham today named John Bahcall, Raymond Davis, Jr. and Seymour Sack as winners of the Enrico Fermi Award. ... Drs. Bahcall and Davis will receive the award for their research in neutrino physics. Dr. Sack will receive the award for his contributions to national security" (1 page).

  11. Analytical relationships for prediction of the mechanical properties of additively manufactured porous biomaterials

    NARCIS (Netherlands)

    Zadpoor, A.A.; Hedayati, R.

    2016-01-01

    Recent developments in additive manufacturing techniques have motivated an increasing number of researchers to study regular porous biomaterials that are based on repeating unit cells. The physical and mechanical properties of such porous biomaterials have therefore received increasing attention

  12. Modeling study on the thermal performance of a modified cavity receiver with glass window and secondary reflector

    International Nuclear Information System (INIS)

    Chang, Huawei; Duan, Chen; Wen, Ke; Liu, Yuting; Xiang, Can; Wan, Zhongmin; He, Sinian; Jing, Changwei; Shu, Shuiming

    2015-01-01

    Highlights: • A modified cavity receiver with glass window and secondary reflector is presented. • Optical and thermal performance of the modified cavity receiver is investigated. • Effects of glass window and secondary reflector are analyzed with comparison study. - Abstract: The development of a cavity receiver for a 1 kW beta type solar Stirling engine is presented in this work. The proposed receiver is composed of an additional quartz glass window and a secondary reflector aiming at improving the thermal performance. Monte-Carlo ray-tracing method is adopted to study the optical property and calculate radiative exchange factors of the solar collector system. The results show that the radiation flux sent to the proposed cavity receiver is 5003 W, and the optical efficiency of this receiver is 70.8%. Numerical simulation is conducted to investigate the thermal performance of this modified receiver. The proposed receiver is also compared with other three simulated receivers combining the presence and absence of the quartz glass window and the secondary reflector. The numerical simulation results show that the modified receiver with both quartz glass window and secondary trumpet reflector outperformed other designs, and its heat loss is reduced about 56% compared to the initial receiver without both quartz glass window and secondary reflector. Hence, the impact factors on the modified receiver radiation and convection heat transfer are well analyzed including temperature, the inner surface orientation and emissivity. The research indicates that the proposed cavity receiver can efficiently reduce the heat loss from cavity and is suitable for Stirling engine applications.

  13. Additive Manufacturing Infrared Inspection

    Science.gov (United States)

    Gaddy, Darrell; Nettles, Mindy

    2015-01-01

    The Additive Manufacturing Infrared Inspection Task started the development of a real-time dimensional inspection technique and digital quality record for the additive manufacturing process using infrared camera imaging and processing techniques. This project will benefit additive manufacturing by providing real-time inspection of internal geometry that is not currently possible and reduce the time and cost of additive manufactured parts with automated real-time dimensional inspections which deletes post-production inspections.

  14. Broadband direct RF digitization receivers

    CERN Document Server

    Jamin, Olivier

    2014-01-01

    This book discusses the trade-offs involved in designing direct RF digitization receivers for the radio frequency and digital signal processing domains.  A system-level framework is developed, quantifying the relevant impairments of the signal processing chain, through a comprehensive system-level analysis.  Special focus is given to noise analysis (thermal noise, quantization noise, saturation noise, signal-dependent noise), broadband non-linear distortion analysis, including the impact of the sampling strategy (low-pass, band-pass), analysis of time-interleaved ADC channel mismatches, sampling clock purity and digital channel selection. The system-level framework described is applied to the design of a cable multi-channel RF direct digitization receiver. An optimum RF signal conditioning, and some algorithms (automatic gain control loop, RF front-end amplitude equalization control loop) are used to relax the requirements of a 2.7GHz 11-bit ADC. A two-chip implementation is presented, using BiCMOS and 65nm...

  15. Russian institute receives CMS Gold Award

    CERN Multimedia

    Patrice Loïez

    2003-01-01

    The Snezhinsk All-Russian Institute of Scientific Research for Technical Physics (VNIITF) of the Russian Federal Nuclear Centre (RFNC) is one of twelve CMS suppliers to receive awards for outstanding performance this year. The CMS Collaboration took the opportunity of the visit to CERN of the Director of VNIITF and his deputy to present the CMS Gold Award, which the institute has received for its exceptional performance in the assembly of steel plates for the CMS forward hadronic calorimeter. This calorimeter consists of two sets of 18 wedge-shaped modules arranged concentrically around the beam-pipe at each end of the CMS detector. Each module consists of steel absorber plates with quartz fibres inserted into them. The institute developed a special welding technique to assemble the absorber plates, enabling a high-quality detector to be produced at relatively low cost.RFNC-VNIITF Director Professor Georgy Rykovanov (right), is seen here receiving the Gold Award from Felicitas Pauss, Vice-Chairman of the CMS ...

  16. Metodología de una Investigación sobre Métodos de Enseñanza de Problemas Aditivos con Números Negativos (Methodology for a Research about Teaching Methods of Additive Problems with Negative Numbers

    Directory of Open Access Journals (Sweden)

    Alicia Bruno

    2009-01-01

    Full Text Available Se presenta la metodología de una investigación de aula donde se contrastan dos métodos de enseñanza de problemas aditivos con números negativos. En el “método redactar” los alumnos enuncian los problemas, aprenden sus estructuras y resuelven problemas propuestos por sus compañeros. En el “método resolver” se practican los problemas en una secuencia marcada por un orden de dificultad. El conocimiento adquirido se contrastó con el de otros alumnos que resolvieron problemas del libro de texto como aplicación de reglas operatorias. La metodología conjuga un tratamiento estadístico para contrastar la efectividad de los métodos con base en el éxito en la resolución y un estudio cualitativo de ciertos aspectos del “método redactar”. We present a research methodology used in a classroom study in which two different learning methods of additive problems with negative numbers are compared. With the “writing method” students write the problems, learn their structures and solve problems that have been written by their partners. With the “solving method” students practice additive problems in a given sequence, according to the problems level of difficulty. The knowledge acquired was compared with the one obtained by other students who solved additive problems from the textbook, as application of operational rules. We have used a mixed methodology: A statistical treatment to contrast the effectiveness of the methods for solving problems and a qualitative study of certain aspects of the “writing method”.

  17. Addition of electric arc furnace dust in hot metal changing the form of addition

    International Nuclear Information System (INIS)

    Marques Sobrinho, Vicente de Paulo Ferreira; Oliveira, Jose Roberto de; Vieira, Estefano Aparecido; Telles, Victor Bridi; Grillo, Felipe Fardin; Tenorio, Jorge Alberto Soares; Espinosa, Denise Crocce Romano

    2014-01-01

    This research aims to study the incorporation of the mass of electric arc furnace dust (EAFD), by addition in hot metal (1.78% Si) at a temperature of 1,400 degrees Celsius. The EAFD is from a steel plant producing long steel. The addition of the EAFD was as received, in the form of briquettes without agitation of the hot metal and in the form of briquettes with agitation of the hot metal. Previously, the EAFD was characterized using the following techniques: chemical analysis, size analysis, X-ray diffraction, scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) microanalysis. The achievement of fusion experiments in laboratory scale, took place in a vertical tubular furnace with temperature control. The fusion experiments to assess the incorporation of EAFD mass used graphite crucibles. After cooling, the hot metal and the slag, remaining in the crucible, were weighed to do a mass balance. A flow of inert gas (argon) was maintained inside the furnace during the experiments. Results show that the experiment with addition of EAFD as received presents the best result of incorporating the mass of the final hot metal (1.73%) combined with the lowest percentage of volatilized mass of EAFD (46.52%). The experiment addition of EAFD in the form of briquette with agitation of hot metal presents the lowest percentage of slag mass (4.58%). The zinc content of volatilized EAFD (64.30%) is higher than the zinc content of the imported ore concentrate (52%) and zinc content of the national ore concentrate (12% to 39%). The presence of lead and cadmium in the slag characterizing it as a hazardous solid waste. (author)

  18. Global Positioning System (GPS) Receiver Design For Multipaths Mitigation

    National Research Council Canada - National Science Library

    Gadallah, El-Sayed

    1998-01-01

    .... This research introduces a new estimator that can detect the presence of multipath, can determine the unknown number of multipath components and can estimate multipath parameters in the GPS receiver...

  19. [Food additives and healthiness].

    Science.gov (United States)

    Heinonen, Marina

    2014-01-01

    Additives are used for improving food structure or preventing its spoilage, for example. Many substances used as additives are also naturally present in food. The safety of additives is evaluated according to commonly agreed principles. If high concentrations of an additive cause adverse health effects for humans, a limit of acceptable daily intake (ADI) is set for it. An additive is a risk only when ADI is exceeded. The healthiness of food is measured on the basis of nutrient density and scientifically proven effects.

  20. Verification of 3G and 4G Received Power Measurements in a Crowdsourcing Android App

    DEFF Research Database (Denmark)

    Lauridsen, Mads; Rodriguez, Ignacio; Mikkelsen, Lars Møller

    2016-01-01

    . In this paper we verify the crowdsourcing Android application NetMap’s ability to measure LTE Reference Signal Received Power by analyzing the Root Mean Squared Error, being 2-3 dB, and cross-correlation coefficient, being above 0.8, with measurements obtained by use of a professional radio network scanner......Many crowdsourcing Android applications are available for measuring network Key Performance Indicators such as received power, latency, and throughput. The data is useful for end-users, researchers, and Mobile Network Operators, but unfortunately the applications’ accuracy are rarely verified...... and measurement phones. In addition, the application is applicable, but less accurate, for 3G Received Signal Code Power measurements. The studies are made for various device speeds and in different scenarios including indoor, urban, and highway, where the NetMap application is showed to perform well....

  1. BOOK MANAGER'S CHOICE BOOKS RECEIVED

    African Journals Online (AJOL)

    progression from qualitative to quantitative methods. He begins with an ethnography of concepts of mental illness held by care providers from both the ... research methods for the southern African context. I heartily recommend this book.

  2. CERN physicist receives Einstein Medal

    CERN Multimedia

    2006-01-01

    On 29 June the CERN theorist Gabriele Veneziano was awarded the prestigious Albert Einstein Medal for significant contributions to the understanding of string theory. This award is given by the Albert Einstein Society in Bern to individuals whose scientific contributions relate to the work of Einstein. Former recipients include exceptional physicists such as Murray Gell-Mann last year, but also Stephen Hawking and Victor Weisskopf. Gabriele Veneziano, a member of the integrated CERN Theory Team since 1977, led the Theory Division from 1994 to 1997 and has already received many prestigious prizes for his outstanding work, including the Enrico Fermi Prize (see CERN Courier, November 2005), the Dannie Heineman Prize for mathematical physics of the American Physical Society in 2004 (see Bulletin No. 47/2003), and the I. Ya. Pomeranchuk Prize of the Institute of Theoretical and Experimental Physics (Moscow) in 1999.

  3. Addition of a Digital Receiver to the X-BADGER Radar System

    Data.gov (United States)

    National Aeronautics and Space Administration — Over the past year, the X-Band Atmospheric Doppler Ground-based Radar (X-BADGER) transmitter has undergone a major upgrade from a high voltage traveling-wave tube to...

  4. Advanced Signal Processing for MIMO-OFDM Receivers

    DEFF Research Database (Denmark)

    Manchón, Carles Navarro

    This thesis deals with a wide range of topics within the research area of advanced baseband receiver design for wireless communication systems. In particular, the work focuses on signal processing algorithms for receivers in multiple-input multiple-output (MIMO) orthogonal frequency-division mult......This thesis deals with a wide range of topics within the research area of advanced baseband receiver design for wireless communication systems. In particular, the work focuses on signal processing algorithms for receivers in multiple-input multiple-output (MIMO) orthogonal frequency...... the structure of the receiver with the hope that the resulting heuristic architecture will exhibit the desired behavior and performance. On the other hand, one can employ analytical frameworks to pose the problem as the optimization of a global objective function subject to certain constraints. This work...

  5. Additives in yoghurt production

    Directory of Open Access Journals (Sweden)

    Milna Tudor

    2008-02-01

    Full Text Available In yoghurt production, mainly because of sensory characteristics, different types of additives are used. Each group, and also each substance from the same group has different characteristics and properties. For that reason, for improvement of yoghurt sensory characteristics apart from addition selection, the quantity of the additive is very important. The same substance added in optimal amount improves yoghurt sensory attributes, but too small or too big addition can reduce yoghurt sensory attributes. In this paper, characteristics and properties of mostly used additives in yoghurt production are described; skimmed milk powder, whey powder, concentrated whey powder, sugars and artificial sweeteners, fruits, stabilizers, casein powder, inulin and vitamins. Also the impact of each additive on sensory and physical properties of yoghurt, syneresis and viscosity, are described, depending on used amount added in yoghurt production.

  6. Polylactides in additive biomanufacturing.

    Science.gov (United States)

    Poh, Patrina S P; Chhaya, Mohit P; Wunner, Felix M; De-Juan-Pardo, Elena M; Schilling, Arndt F; Schantz, Jan-Thorsten; van Griensven, Martijn; Hutmacher, Dietmar W

    2016-12-15

    New advanced manufacturing technologies under the alias of additive biomanufacturing allow the design and fabrication of a range of products from pre-operative models, cutting guides and medical devices to scaffolds. The process of printing in 3 dimensions of cells, extracellular matrix (ECM) and biomaterials (bioinks, powders, etc.) to generate in vitro and/or in vivo tissue analogue structures has been termed bioprinting. To further advance in additive biomanufacturing, there are many aspects that we can learn from the wider additive manufacturing (AM) industry, which have progressed tremendously since its introduction into the manufacturing sector. First, this review gives an overview of additive manufacturing and both industry and academia efforts in addressing specific challenges in the AM technologies to drive toward AM-enabled industrial revolution. After which, considerations of poly(lactides) as a biomaterial in additive biomanufacturing are discussed. Challenges in wider additive biomanufacturing field are discussed in terms of (a) biomaterials; (b) computer-aided design, engineering and manufacturing; (c) AM and additive biomanufacturing printers hardware; and (d) system integration. Finally, the outlook for additive biomanufacturing was discussed. Copyright © 2016 Elsevier B.V. All rights reserved.

  7. Egypt receives computers from CERN

    CERN Multimedia

    Anaïs Schaeffer

    2013-01-01

    On Tuesday 22 October, CERN officially celebrated sending IT equipment to Egypt, the fifth country to benefit from such donations after Morocco, Ghana, Bulgaria and Serbia. Although no longer adequate for CERN's cutting-edge research, these machines are still suitable for less demanding applications.   Rolf Heuer and Amr Radi, during the official ceremony. In a ceremony to mark the occasion, Rolf Heuer, CERN Director-General, and Egyptian physicist Amr Radi, team leader of ASRT (Egypt’s Academy of Scientific Research and Technology) within the CMS collaboration, who has played a major part in the operation, expressed their enthusiasm for the project. A total of 196 servers and 10 routers will be installed on the ASRT premises in Cairo, where they will be used to analyse data from the ALICE and CMS experiments. For more information about CERN’s donations of IT equipment, see this Bulletin article.

  8. Additive and polynomial representations

    CERN Document Server

    Krantz, David H; Suppes, Patrick

    1971-01-01

    Additive and Polynomial Representations deals with major representation theorems in which the qualitative structure is reflected as some polynomial function of one or more numerical functions defined on the basic entities. Examples are additive expressions of a single measure (such as the probability of disjoint events being the sum of their probabilities), and additive expressions of two measures (such as the logarithm of momentum being the sum of log mass and log velocity terms). The book describes the three basic procedures of fundamental measurement as the mathematical pivot, as the utiliz

  9. Evaluation and Error Analysis for a Solar Thermal Receiver

    International Nuclear Information System (INIS)

    Pfander, M.

    2001-01-01

    In the following study a complete balance over the REFOS receiver module, mounted on the tower power plant CESA-1 at the Plataforma Solar de Almeria (PSA), is carried out. Additionally an error inspection of the various measurement techniques used in the REFOS project is made. Especially the flux measurement system Pro hermes that is used to determine the total entry power of the receiver module and known as a major error source is analysed in detail. Simulations and experiments on the particular instruments are used to determine and quantify possible error sources. After discovering the origin of the errors they are reduced and included in the error calculation. The ultimate result is presented as an overall efficiency of the receiver module in dependence on the flux density at the receiver modules entry plane and the receiver operating temperature. (Author) 26 refs

  10. List of documents received by the INDC secretariat

    International Nuclear Information System (INIS)

    1986-04-01

    The Nuclear Data Section of the International Atomic Energy Agency receives documents originated by or for the International Nuclear Data Committee for distribution. This list includes all INDC documents received and distributed by the INDC secretariat during the period January 1984 to March 1986. In addition to the INDC documents received by the INDC Secretariat for distribution, this document also lists the titles of reports received as single copies for information. These documents cannot be obtained from the INDC Secretariat, but should be requested from the originating laboratory or organization. All of the single copy documents, which have been received between January 1984 and March 1986 are listed in Appendix A to this document

  11. List of documents received by the INDC Secretariat

    International Nuclear Information System (INIS)

    1984-08-01

    The Nuclear Data Section of the International Atomic Energy Agency receives documents originated by or for the International Nuclear Data Committee for distribution. The present list includes all INDC documents received and distributed by the INDC secretariat during the period January 1982 to June 1984, and supersedes last years' edition of this report, INDC(SEC)-85/UN. This list is produced directly from computer printout in two sorts: one ordered by accession number, and the other ordered by document number within each origin series (e.g. listing all INDC(SEC)-documents in one block). In addition to the INDC documents received by the INDC Secretariat for distribution, this document also lists the titles of reports received as single copies for information. All of the single copy documents which have been received between June 1983 and July 1984 are listed in Appendix A to this document

  12. Evaluation and Error Analysis for a Solar thermal Receiver

    Energy Technology Data Exchange (ETDEWEB)

    Pfander, M.

    2001-07-01

    In the following study a complete balance over the REFOS receiver module, mounted on the tower power plant CESA-1 at the Plataforma Solar de Almeria (PSA), is carried out. Additionally an error inspection of the various measurement techniques used in the REFOS project is made. Especially the flux measurement system Prohermes that is used to determine the total entry power of the receiver module and known as a major error source is analysed in detail. Simulations and experiments on the particular instruments are used to determine and quantify possible error sources. After discovering the origin of the errors they are reduced and included in the error calculation. the ultimate result is presented as an overall efficiency of the receiver module in dependence on the flux density at the receiver module's entry plane and the receiver operating temperature. (Author) 26 refs.

  13. Food Additives and Hyperkinesis

    Science.gov (United States)

    Wender, Ester H.

    1977-01-01

    The hypothesis that food additives are causally associated with hyperkinesis and learning disabilities in children is reviewed, and available data are summarized. Available from: American Medical Association 535 North Dearborn Street Chicago, Illinois 60610. (JG)

  14. Groups – Additive Notation

    Directory of Open Access Journals (Sweden)

    Coghetto Roland

    2015-06-01

    Full Text Available We translate the articles covering group theory already available in the Mizar Mathematical Library from multiplicative into additive notation. We adapt the works of Wojciech A. Trybulec [41, 42, 43] and Artur Korniłowicz [25].

  15. Groups – Additive Notation

    OpenAIRE

    Coghetto Roland

    2015-01-01

    We translate the articles covering group theory already available in the Mizar Mathematical Library from multiplicative into additive notation. We adapt the works of Wojciech A. Trybulec [41, 42, 43] and Artur Korniłowicz [25].

  16. Hybrid solar central receiver for combined cycle power plant

    Science.gov (United States)

    Bharathan, Desikan; Bohn, Mark S.; Williams, Thomas A.

    1995-01-01

    A hybrid combined cycle power plant including a solar central receiver for receiving solar radiation and converting it to thermal energy. The power plant includes a molten salt heat transfer medium for transferring the thermal energy to an air heater. The air heater uses the thermal energy to preheat the air from the compressor of the gas cycle. The exhaust gases from the gas cycle are directed to a steam turbine for additional energy production.

  17. PENENTUAN RECEIVED DATE DENGAN LOAD-ORIENTED MANUFACRURING CONTROL

    Directory of Open Access Journals (Sweden)

    Sri Hartini

    2012-02-01

    Full Text Available Salah satu kunci kompetitif sebuah perusahaan make to order adalah ketepatan dalam pemenuhan waktu penerimaan pesanan pada konsumen yang telah dijanjikan perusahaan ( received date. Penentuan received date yang selama ini dilakukan oleh JI  kurang tepat karena hanya memperkirakan waktu sekitar 10 – 12 minggu tanpa mempertimbangkan faktor produksi. Penelitian ini merancang received date dengan model load-oriented manufacturing control dimana penentuan received date didasarkan pada perhitungan manufacturing lead time yang mempertimbangkan waktu pengiriman order ke konsumen, kapasitas yang tersedia pada tiap stasiun kerja, waktu proses pada stasiun kerja dan aliran produksi di lantai produksi. Hasil validasi perhitungan  penentuan received date order sesuai  dengan sistem produksi PT JI dan lebih valid dibanding sistem awal. Kata kunci : make to order, received date, manufacturing leadtime, load-oriented manufacturing control   One of the competitive key of a make to order company is the accuracy in fulfilling orders which has been promised by the company towards the consumers (received date. Determining received date which has been applied by JI recently is not sufficient because it only predicts 10-12 weeks of time without considering production factors. This research designs received date with load-oriented manufacturing control model where determining received date is based on calculating manufacturing lead time that considers the time needed to deliver orders to the consumer, capacity available for each work station, work station process time, and production flow within the production floor.  Validation results from the calculations for determining received date order is adjusted to PT JI  production system and is more valid than the first system. Keywords : make to order, received date, manufacturing leadtime, load-oriented manufacturing control

  18. Morel Receives 2005 Maurice Ewing Medal

    Science.gov (United States)

    Schrag, Daniel P.; Morel, François M. M.

    2006-02-01

    François M. M. Morel received the Ewing Medal at the AGU Fall Meeting Honors Ceremony, which was held on 7 December 2005, in San Francisco, Calif. The medal is given for significant original contributions to the scientific understanding of the processes in the ocean; for the advancement of oceanographic engineering, technology, and instrumentation; and for outstanding service to marine sciences. François Morel has led the search to understand the role of metals in the ocean, starting with a focus on inorganic processes and aquatic chemistry, and leading to a blend of geochemistry, microbiology, biochemistry, and genetics. His influence comes from his research and from the way he has educated an entire community of scientists with his textbooks, with his teaching, and through his former students and postdocs who hold faculty positions at universities throughout the world.

  19. Received View of Addiction, Relapse and Treatment.

    Science.gov (United States)

    Ndasauka, Yamikani; Wei, Zhengde; Zhang, Xiaochu

    2017-01-01

    It is important to highlight that attempts at understanding and explaining addiction have been made for centuries. It is, however, just five decades ago, with the growth of science and technology that more interest has been observed in this field. This chapter examines different views and theories that have been posited to understand and explain addiction. More attention will be given to prominent views that seem to draw consensus among researchers and medical practitioners. The first section of the chapter introduces the addiction debate, the different theories that have been provided to explain it from different perspectives and disciplines such as neurosciences, philosophy and psychology. Then, the chapter discusses different views on the role of relapse and what it entails in understanding addiction. The second section discusses different proposed and used forms of treating addiction. Thus, the chapter discusses the received view of addiction, the understanding of relapse as a critical element in addiction and treatments.

  20. Food additives and preschool children.

    Science.gov (United States)

    Martyn, Danika M; McNulty, Breige A; Nugent, Anne P; Gibney, Michael J

    2013-02-01

    Food additives have been used throughout history to perform specific functions in foods. A comprehensive framework of legislation is in place within Europe to control the use of additives in the food supply and ensure they pose no risk to human health. Further to this, exposure assessments are regularly carried out to monitor population intakes and verify that intakes are not above acceptable levels (acceptable daily intakes). Young children may have a higher dietary exposure to chemicals than adults due to a combination of rapid growth rates and distinct food intake patterns. For this reason, exposure assessments are particularly important in this age group. The paper will review the use of additives and exposure assessment methods and examine factors that affect dietary exposure by young children. One of the most widely investigated unfavourable health effects associated with food additive intake in preschool-aged children are suggested adverse behavioural effects. Research that has examined this relationship has reported a variety of responses, with many noting an increase in hyperactivity as reported by parents but not when assessed using objective examiners. This review has examined the experimental approaches used in such studies and suggests that efforts are needed to standardise objective methods of measuring behaviour in preschool children. Further to this, a more holistic approach to examining food additive intakes by preschool children is advisable, where overall exposure is considered rather than focusing solely on behavioural effects and possibly examining intakes of food additives other than food colours.

  1. Alternative additives; Alternative additiver

    Energy Technology Data Exchange (ETDEWEB)

    2007-08-15

    In this project a number of industrial and agricultural waste products have been characterised and evaluated in terms of alkali-getter performance. The intended use is for biomass-fired power stations aiming at reducing corrosion or slagging related problems. The following products have been obtained, characterised and evaluated: 1) Brewery draff 2) Danish de-gassed manure 3) Paper sludge 4) Moulding sand 5) Spent bleaching earth 6) Anorthosite 7) Sand 8) Clay-sludge. Most of the above alternative additive candidates are deemed unsuitable due to insufficient chemical effect and/or expensive requirements for pre-treatment (such as drying and transportation). 3 products were selected for full-scale testing: de-gassed manure, spent bleaching earth and clay slugde. The full scale tests were undertaken at the biomass-fired power stations in Koege, Slagelse and Ensted. Spent bleaching earth (SBE) and clay sludge were the only tested additive candidates that had a proven ability to react with KCl, to thereby reduce Cl-concentrations in deposits, and reduce the deposit flux to superheater tubes. Their performance was shown to nearly as good as commercial additives. De-gassed manure, however, did not evaluate positively due to inhibiting effects of Ca in the manure. Furthermore, de-gassed manure has a high concentration of heavy metals, which imposes a financial burden with regard to proper disposal of the ash by-products. Clay-sludge is a wet clay slurring, and drying and transportation of this product entails substantial costs. Spent bleaching does not require much pre-treatment and is therefore the most promising alternative additive. On the other hand, bleaching earth contains residual plant oil which means that a range of legislation relating to waste combustion comes into play. Not least a waste combustion fee of 330 DKK/tonne. For all alternative (and commercial) additives disposal costs of the increase ash by-products represents a significant cost. This is

  2. Features of the compost received by use of dairy whey

    Directory of Open Access Journals (Sweden)

    V. V. Smolnikova

    2010-01-01

    Full Text Available In the article features cjmposting of organic materials are considered at use of a traditional way and fermenting additives. Indicators of quality of the composts received with the use of dairy whey and a bacterial preparation as the fermenting additive are investigated. Comparison of the received samples of composts on such indicators of quality as is spent: humidity, acidity, the maintenance of organic substance in recalculation on dry weight, quantity of the general and fmmonium nitrogen.

  3. Model Additional Protocol

    International Nuclear Information System (INIS)

    Rockwood, Laura

    2001-01-01

    Since the end of the cold war a series of events has changed the circumstances and requirements of the safeguards system. The discovery of a clandestine nuclear weapons program in Iraq, the continuing difficulty in verifying the initial report of Democratic People's Republic of Korea upon entry into force of their safeguards agreement, and the decision of the South African Government to give up its nuclear weapons program and join the Treaty on the Non-Proliferation of Nuclear Weapons have all played a role in an ambitious effort by IAEA Member States and the Secretariat to strengthen the safeguards system. A major milestone in this effort was reached in May 1997 when the IAEA Board of Governors approved a Model Protocol Additional to Safeguards Agreements. The Model Additional Protocol was negotiated over a period of less than a year by an open-ended committee of the Board involving some 70 Member States and two regional inspectorates. The IAEA is now in the process of negotiating additional protocols, State by State, and implementing them. These additional protocols will provide the IAEA with rights of access to information about all activities related to the use of nuclear material in States with comprehensive safeguards agreements and greatly expanded physical access for IAEA inspectors to confirm or verify this information. In conjunction with this, the IAEA is working on the integration of these measures with those provided for in comprehensive safeguards agreements, with a view to maximizing the effectiveness and efficiency, within available resources, the implementation of safeguards. Details concerning the Model Additional Protocol are given. (author)

  4. Researching research

    DEFF Research Database (Denmark)

    Pais, Alexandre; Valero, Paola

    2012-01-01

    We discuss contemporary theories in mathematics education in order to do research on research. Our strategy consists of analysing discursively and ideologically recent key publications addressing the role of theory in mathematics education research. We examine how the field fabricates its object...... of research by deploying Foucault’s notion of bio-politics - mainly to address the object “learning” - and Žižek’s ideology critique - to address the object “mathematics”. These theories, which have already been used in the field to research teaching and learning, have a great potential to contribute...... to a reflexivity of research on its discourses and effects. Furthermore, they enable us to present a clear distinction between what has been called the sociopolitical turn in mathematics education research and what we call a positioning of mathematics education (research) practices in the Political....

  5. Oil additive and its effect

    Directory of Open Access Journals (Sweden)

    Vojtěch Kumbár

    2013-01-01

    Full Text Available The aim of this paper are experimental approaches, selected for analysis of the engine oils and described above, are surely sufficient for the needs of presented research. The spectrometry was used for determination of presence of selected chemical elements and especially metals in oil. Particles monitoring was employed in order to describe the amount, type, and size of friction particles. The temperature dependence of dynamic viscosity was evaluated by use of rotary viscometer. In case of all three approaches it is advantageous to compare the measured values with the results received for unused engine oil of the same marking and viscosity index. If the degradation of oil is classified as low or medium, it is possible to increase its service life for several thousands of kilometers. Mathematical model (polynomial 6th degree it was used for fitting experimental values.

  6. Septic tank additive impacts on microbial populations.

    Science.gov (United States)

    Pradhan, S; Hoover, M T; Clark, G H; Gumpertz, M; Wollum, A G; Cobb, C; Strock, J

    2008-01-01

    Environmental health specialists, other onsite wastewater professionals, scientists, and homeowners have questioned the effectiveness of septic tank additives. This paper describes an independent, third-party, field scale, research study of the effects of three liquid bacterial septic tank additives and a control (no additive) on septic tank microbial populations. Microbial populations were measured quarterly in a field study for 12 months in 48 full-size, functioning septic tanks. Bacterial populations in the 48 septic tanks were statistically analyzed with a mixed linear model. Additive effects were assessed for three septic tank maintenance levels (low, intermediate, and high). Dunnett's t-test for tank bacteria (alpha = .05) indicated that none of the treatments were significantly different, overall, from the control at the statistical level tested. In addition, the additives had no significant effects on septic tank bacterial populations at any of the septic tank maintenance levels. Additional controlled, field-based research iswarranted, however, to address additional additives and experimental conditions.

  7. Interactive, Web-based Information Skills Tutorial Well Received by Graduate Students in Health and Social Care Research. A review of: Grant, Maria J., and Alison J. Brettle. “Developing and Evaluating an Interactive Information Skills Tutorial.” Health Information and Libraries Journal 23.2 (June 2006: 79 ‐86.

    Directory of Open Access Journals (Sweden)

    Marcy L. Brown

    2007-03-01

    Full Text Available Objective – To determine whether a newly developed interactive, Web -based tutorial on OVID MEDLINE was acceptable to students, and to identify whether the tutorial improved students’ information skills. Design – Objective and subjective assessment within a small cohort study. Setting – An evidence based practice module within a Master's in Research (MRes program at the University of Salford, UK. Subjects – A total of 13 usable evaluations were received from graduate students who took an evidence based practice module as part of their MRes coursework. Methods – Information skills (IS were taught in weeks two and three of a 12 ‐week module on evidence based practice. Each of the two IS sessions lasted approximately three hours. At the beginning of the first session, baseline skills were assessed by asking the students to perform a literature search on either the effectiveness of nursing interventions for smoking cessation, or the effectiveness of rehabilitation after stroke. The OVID MEDLINE tutorial was introduced at the first session, and guided hands ‐on practice was offered. Homework was given, and between ‐session use of the tutorial was encouraged. At the end of the second session, students were asked to complete another search in order to assess short ‐term impact of the tutorial. Both sets of search results were scored using a checklist rubric that looked for Boolean operators, use of MeSH terms, use of limits, number and relevance of references, and other assessment criteria. The rubric was a modified version of a tool published by Rosenberg et al. The tutorial remained available throughout the 12 ‐week module, at which time a systematic literature review was assigned in order to measure longer ‐term impact. As an additional subjective measurement, a questionnaire regarding the information skills sessions and tutorial was given at the end of the second IS session (week 3. Main Results – Thirteen objective

  8. Water jacket for solid particle solar receiver

    Science.gov (United States)

    Wasyluk, David T.

    2018-03-20

    A solar receiver includes: water jacket panels each having a light-receiving side and a back side with a watertight sealed plenum defined in-between; light apertures passing through the watertight sealed plenums to receive light from the light-receiving sides of the water jacket panels; a heat transfer medium gap defined between the back sides of the water jacket panels and a cylindrical back plate; and light channeling tubes optically coupled with the light apertures and extending into the heat transfer medium gap. In some embodiments ends of the light apertures at the light receiving side of the water jacket panel are welded together to define at least a portion of the light-receiving side. A cylindrical solar receiver may be constructed using a plurality of such water jacket panels arranged with their light-receiving sides facing outward.

  9. Additive manufacturing of metals

    International Nuclear Information System (INIS)

    Herzog, Dirk; Seyda, Vanessa; Wycisk, Eric; Emmelmann, Claus

    2016-01-01

    Additive Manufacturing (AM), the layer-by layer build-up of parts, has lately become an option for serial production. Today, several metallic materials including the important engineering materials steel, aluminium and titanium may be processed to full dense parts with outstanding properties. In this context, the present overview article describes the complex relationship between AM processes, microstructure and resulting properties for metals. It explains the fundamentals of Laser Beam Melting, Electron Beam Melting and Laser Metal Deposition, and introduces the commercially available materials for the different processes. Thereafter, typical microstructures for additively manufactured steel, aluminium and titanium are presented. Special attention is paid to AM specific grain structures, resulting from the complex thermal cycle and high cooling rates. The properties evolving as a consequence of the microstructure are elaborated under static and dynamic loading. According to these properties, typical applications are presented for the materials and methods for conclusion.

  10. Additive manufactured serialization

    Science.gov (United States)

    Bobbitt, III, John T.

    2017-04-18

    Methods for forming an identifying mark in a structure are described. The method is used in conjunction with an additive manufacturing method and includes the alteration of a process parameter during the manufacturing process. The method can form in a unique identifying mark within or on the surface of a structure that is virtually impossible to be replicated. Methods can provide a high level of confidence that the identifying mark will remain unaltered on the formed structure.

  11. Paterson Receives 2004 Walter H. Bucher Medal

    Science.gov (United States)

    Jackson, Ian

    2005-01-01

    Mervyn S. Paterson received the Bucher Medal at the 2004 Fall Meeting Honors Ceremony on 15 December, in San Francisco, California. The medal is given for original contributions to the basic knowledge of the crust and lithosphere. Citation. It is the nature of modern research in the Earth sciences that observations of natural phenomena are often made and interpreted through the prism provided by the enabling sciences and technologies. Thus it has been with Mervyn Paterson's career. His undergraduate training in engineering in Adelaide formed the basis for his Ph.D. study of X-ray line-broadening in cold-worked metals under Orowan at Cambridge. This interest in the deformation of metals was fostered during his employment at the Aeronautical Research Laboratories in Melbourne and by postdoctoral experience at the Institute of Metals at the University of Chicago. Mervyn's general background in engineering and his particular interest in mechanical behavior have underpinned a distinguished career at the Australian National University in the experimental deformation of rocks, providing fundamental new insight into the mechanical behavior of the Earth's crust.

  12. Design of double capacitances infrasonic receiver

    International Nuclear Information System (INIS)

    Wang Changhai; Han Kuixia; Wang Fei

    2003-01-01

    The article introduces the theory of infrasonic generation and reception of nuclear explosion. An idea of the design of double capacitances infrasonic receiver using CPLD technology is given in it. Compare with the single capacitance infrasonic receiver, sensitivity of the improved receiver can be improved scores of times, dynamic range can be improved largely, and the whole performance gets improvement a lots

  13. 29 CFR 1917.155 - Air receivers.

    Science.gov (United States)

    2010-07-01

    .... This section applies to compressed air receivers and equipment used for operations such as cleaning... transportation applications as railways, vehicles or cranes. (b) Gauges and valves. (1) Air receivers shall be... 29 Labor 7 2010-07-01 2010-07-01 false Air receivers. 1917.155 Section 1917.155 Labor Regulations...

  14. 49 CFR 393.88 - Television receivers.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 5 2010-10-01 2010-10-01 false Television receivers. 393.88 Section 393.88... NECESSARY FOR SAFE OPERATION Miscellaneous Parts and Accessories § 393.88 Television receivers. Any motor vehicle equipped with a television viewer, screen or other means of visually receiving a television...

  15. 21 CFR 1020.10 - Television receivers.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Television receivers. 1020.10 Section 1020.10 Food...) RADIOLOGICAL HEALTH PERFORMANCE STANDARDS FOR IONIZING RADIATION EMITTING PRODUCTS § 1020.10 Television receivers. (a) Applicability. The provisions of this section are applicable to television receivers...

  16. Heat receivers for solar dynamic space power systems

    Science.gov (United States)

    Perez-Davis, Marla Esther

    A review of state-of-the-art technology is presented and discussed for phase change materials. Some of the advanced solar dynamic designs developed as part of the Advanced Heat Receiver Conceptual Design Study performed for LeRC are discussed. The heat receivers are analyzed and several recommendations are proposed, including two new concepts. The first concept evaluated the effect of tube geometries inside the heat receiver. It was found that a triangular configuration would provide better heat transfer to the working fluid, although not necessarily with a reduction in receiver size. A sensible heat receiver considered in this study uses vapor grown graphite fiber-carbon (VGCF/C) composite as the thermal storage media and was designed for a 7 kW Brayton engine. The proposed heat receiver stores the required energy to power the system during eclipse in the VGCF/C composite. The heat receiver analysis was conducted through the Systems Improved Numerical Differencing Analyzer and Fluid Integrator (SINDA) software package. The proposed heat receiver compares well with other latent and advanced sensible heat receivers while avoiding the problems associated with latent heat storage salts and liquid metal heat pipes. The weight and size of the system can be optimized by changes in geometry and technology advances for this new material. In addition to the new concepts, the effect of atomic oxygen on several materials is reviewed. A test was conducted for atomic oxygen attack on boron nitride, which experienced a negligible mass loss when exposed to an atomic oxygen fluence of 5 x 10 exp 21 atoms/sq cm. This material could be used to substitute the graphite aperture plate of the heat receiver.

  17. Influence of metallic additives on manganese ferrites sintering

    Science.gov (United States)

    Shevelev, S. A.; Luchnikov, P. A.; Yarullina, A. R.

    2018-01-01

    Influence of cuprum nanopowder additive received by electric explosion on the process of manganese ferrites MgFe2O4 consolidating at thermal sintering was researched by dilatometry method. Cuprum nanopowder at a rate of 5 mass % was added into the original commercial-grade powder of manganese ferrite MgFe2O4. Powder mixture was numerously blended with screening for better blending before pressing. Powder compacts were formed by cold one-axle static pressing. It was proved that introduction of cuprum additive caused shrinkage increase at final heating stage. There was abnormal compact enlarging at sintering in the air at isothermal stage; the specified process was not observed in vacuum. This difference can be explained by changes in conditions of gaseous discharge from volume of pores.

  18. Radioactive contamination in monitors received for calibration

    International Nuclear Information System (INIS)

    Dias, Paulo S.; Santos, Gilvan C. dos; Brunelo, Maria Antonieta G.; Paula, Tiago C. de; Pires, Marina A.; Borges, Jose C.

    2013-01-01

    The Calibration Laboratory - LABCAL, from the Research Center for Metrology and Testing - METROBRAS, MRA Comercio de Instrumentos Eletronicos Ltda., began activities in October 2008 and, in August 2009, decided to establish a procedure for monitoring tests, external and internal, of all packages received from customers, containing instruments for calibration. The aim was to investigate possible contamination radioactive on these instruments. On July 2011, this procedure was extended to packagings of personal thermoluminescent dosemeters - TLD, received by the newly created Laboratory Laboratorio de Dosimetria Pessoal - LDP . In the monitoring procedure were used monitors with external probe, type pancake, MRA brand, models GP - 500 and MIR 7028. During the 37 months in which this investigation was conducted, were detected 42 cases of radioactive contamination, with the following characteristics: 1) just one case was personal dosimeter, TLD type; 2) just one case was not from a packing from nuclear medicine service - was from a mining company; 3) contamination occurred on packs and instruments, located and/or widespread; 4) contamination values ranged from slightly above the level of background radiation to about a thousand fold. Although METROBRAS has facilities for decontamination, in most cases, especially those of higher contamination, the procedure followed was to store the contaminated material in a room used for storage of radioactive sources. Periodically, each package and/or instrument was monitored, being released when the radiation level matched the background radiation. Every contamination detected, the client and/or owner of the instrument was informed. The Brazilian National Energy Commission - CNEN, was informed, during your public consultation for reviewing the standard for nuclear medicine services, held in mid-2012, having received from METROBRAS the statistical data available at the time. The high frequency of contamination detected and the high

  19. Asymmetric Hardware Distortions in Receive Diversity Systems: Outage Performance Analysis

    KAUST Repository

    Javed, Sidrah; Amin, Osama; Ikki, Salama S.; Alouini, Mohamed-Slim

    2017-01-01

    This paper studies the impact of asymmetric hardware distortion (HWD) on the performance of receive diversity systems using linear and switched combining receivers. The asymmetric attribute of the proposed model motivates the employment of improper Gaussian signaling (IGS) scheme rather than the traditional proper Gaussian signaling (PGS) scheme. The achievable rate performance is analyzed for the ideal and non-ideal hardware scenarios using PGS and IGS transmission schemes for different combining receivers. In addition, the IGS statistical characteristics are optimized to maximize the achievable rate performance. Moreover, the outage probability performance of the receive diversity systems is analyzed yielding closed form expressions for both PGS and IGS based transmission schemes. HWD systems that employ IGS is proven to efficiently combat the self interference caused by the HWD. Furthermore, the obtained analytic expressions are validated through Monte-Carlo simulations. Eventually, non-ideal hardware transceivers degradation and IGS scheme acquired compensation are quantified through suitable numerical results.

  20. Asymmetric Hardware Distortions in Receive Diversity Systems: Outage Performance Analysis

    KAUST Repository

    Javed, Sidrah

    2017-02-22

    This paper studies the impact of asymmetric hardware distortion (HWD) on the performance of receive diversity systems using linear and switched combining receivers. The asymmetric attribute of the proposed model motivates the employment of improper Gaussian signaling (IGS) scheme rather than the traditional proper Gaussian signaling (PGS) scheme. The achievable rate performance is analyzed for the ideal and non-ideal hardware scenarios using PGS and IGS transmission schemes for different combining receivers. In addition, the IGS statistical characteristics are optimized to maximize the achievable rate performance. Moreover, the outage probability performance of the receive diversity systems is analyzed yielding closed form expressions for both PGS and IGS based transmission schemes. HWD systems that employ IGS is proven to efficiently combat the self interference caused by the HWD. Furthermore, the obtained analytic expressions are validated through Monte-Carlo simulations. Eventually, non-ideal hardware transceivers degradation and IGS scheme acquired compensation are quantified through suitable numerical results.

  1. More Efficient Solar Thermal-Energy Receiver

    Science.gov (United States)

    Dustin, M. O.

    1987-01-01

    Thermal stresses and reradiation reduced. Improved design for solar thermal-energy receiver overcomes three major deficiencies of solar dynamic receivers described in literature. Concentrator and receiver part of solar-thermal-energy system. Receiver divided into radiation section and storage section. Concentrated solar radiation falls on boiling ends of heat pipes, which transmit heat to thermal-energy-storage medium. Receiver used in number of applications to produce thermal energy directly for use or to store thermal energy for subsequent use in heat engine.

  2. Advances in Additive Manufacturing

    Science.gov (United States)

    2016-07-14

    with a collection of information if it does not display a currently valid OMB control number. PLEASE DO NOT RETURN YOUR FORM TO THE ABOVE ADDRESS...Hamilton • Beth Bimber Air Force Research Laboratory, Metals Branch • Eddie Schwalbach • Mike Groeber • Benjamin Leever • James Hardin...conducting more in-field, or point-of-need, manufacturing than ever before. Other areas of concentration include man- machine interface, capabilities

  3. 200 and 270 GHz SIS receivers development for atmospheric observation

    International Nuclear Information System (INIS)

    Ochiai, S.; Masuko, H.

    1993-01-01

    Superconducting mixers have been developed for observations of atmospheric minor constituents such as ClO and ozone at Communications Research Laboratory. This paper describes the work at development of 200 and 270 GHz SIS mixers. Nb/AlOx/Nb junctions were fabricated at Nobeyama Radio Observatory. The base Nb layer 200 nm, the Al (AlOx) insulation layer, and the counter Nb electrode 150 nm are sputtered. The area outside of a junction defined by etching of the counter electrode is insulated by anodized Nb layer and sputtered SiO 2 . After sputtering thick SiO 2 layer on the whole wafer, a contact hole is made by etching. The thickness of the wiring Nb layer is 500 nm. The junctions are formed on the 250 μm thick fused quartz substrate. After the process of the junction fabrication, the quartz substrate is shaved from the back side until 150 μm thickness. Each junction for 270 GHz mixer has an area of about 1 μm 2 . The normal resistance of the six junctions series array is around 70 Ω. The mixer block has a reduced waveguide (1.2 x 0.1 mm for 200 GHz and 0.98 x 0. 1 mm for 270 GHz). The waveguide has two tuners in addition to a fixed backshort cavity. This configuration can allow to realize the lower embedding impedance, and less sensitive to the position of the tuners. The SIS mixers are cooled in a closed cycle He refrigerator. The LO is optically injected through a Fabry Perot interferometer. The 5--7 GHz IF is fed to a HEMT amplifier cooled at 15 K. The authors have started a preliminary measurement of the noise temperature of the SIS receivers, and comparing with calculated DSB receiver noise temperature assuming 3-port model. They continue to improve the performance of the SIS mixers now. They intend that the receivers shall be utilized for atmospheric monitor from next winter

  4. List of documents received by the INDC Secretariat

    International Nuclear Information System (INIS)

    1975-12-01

    The documents received by the International Nuclear Data Committee after the issuance of INDC (SEC)-48/U in July 1975 are listed: (a) ordered by Accession Number and (b) ordered by Origin Designator. Nine additional single-copy documents are given in an appendix

  5. How to interpret a small increase in AUC with an additional risk prediction marker: decision analysis comes through

    NARCIS (Netherlands)

    Baker, Stuart G.; Schuit, Ewoud; Steyerberg, Ewout W.; Pencina, Michael J.; Vickers, Andrew; Vickers, Andew; Moons, Karel G. M.; Mol, Ben W. J.; Lindeman, Karen S.

    2014-01-01

    An important question in the evaluation of an additional risk prediction marker is how to interpret a small increase in the area under the receiver operating characteristic curve (AUC). Many researchers believe that a change in AUC is a poor metric because it increases only slightly with the

  6. Additive manufacturing in maxillofacial reconstruction

    Directory of Open Access Journals (Sweden)

    Dincă Luciana Laura

    2017-01-01

    Full Text Available In this paper the benefits of using additive manufacturing technologies in maxillofacial reconstruction are highlighted. Based on a real clinical case, the paper describes the manufacture of an implant prototype replacing the right zygomatic bone and a part of maxilla using additive manufacturing technologies. The face is the most expressive part of the human body that makes us unique. It was shown that the maxillofacial prostheses help to improve the psychological state of patients affected by, because low self esteem feeling appears commonly to this patients with the facial defects. The aim of this paper is to show how using additive manufacturing technologies methods within this research, the producing a surgical model will help surgeon to improve the pre-operative planning. For this we used additive manufacturing technologies such as Stereolitography to achieve the biomodel and FDM-fused deposition modelling to obtain a prototype model because these technologies make it possible to obtain prosthesis according to the physical and mechanical requirements of the region of implantation.

  7. Every second cancer patient receives radiotherapy

    International Nuclear Information System (INIS)

    Ojala, A.

    1996-01-01

    Radiotherapy to treat cancer was given for the first time exactly one hundred years ago. Today, radiotherapy and surgery are the two main modes of treating cancer. One in two cancer patients receives radiotherapy at some point during the course of treatment for the disease. Radiotherapy is applied most commonly in cases where surgery is not possible. Moreover, these two modes of treatment are often used together to supplement each other. About half of new cancer cases detected today can be ordered. The estimate given by the EU for cancers cured is 45 per cent, which is divided between the various treatment modes as follows: surgery 22 %, radiotherapy 12 %, surgery plus radiotherapy 6 %, and drug therapy 6 %. In addition to curative treatment, radiotherapy plays a crucial role in palliative treatment, i.e. treatment that alleviates symptoms. The sensitivity of malignant tumours to radiotherapy varies over a wide range; the same is true for healthy tissues. Radiotherapy can only be used to cure a tumour that is more sensitive to radiation than the surrounding healthy tissue. The tumour must also be sufficiently small in size and limited to a relatively small area. (orig.)

  8. United States Department of Energy solar receiver technology development

    Science.gov (United States)

    Klimas, P. C.; Diver, R. B.; Chavez, J. M.

    The United States Department of Energy (DOE), through Sandia National Laboratories, has been conducting a Solar Thermal Receiver Technology Development Program, which maintains a balance between analytical modeling, bench and small scale testing, and experimentation conducted at scales representative of commercially-sized equipment. Central receiver activities emphasize molten salt-based systems on large scales and volumetric devices in the modeling and small scale testing. These receivers are expected to be utilized in solar power plants rated between 100 and 200 MW. Distributed receiver research focuses on liquid metal refluxing devices. These are intended to mate parabolic dish concentrators with Stirling cycle engines in the 5 to 25 kW(sub e) power range. The effort in the area of volumetric receivers is less intensive and highly cooperative in nature. A ceramic foam absorber of Sandia design was successfully tested on the 200 kW(sub t) test bed at Plataforma Solar during 1989. Material integrity during the approximately 90-test series was excellent. Significant progress has been made with parabolic dish concentrator-mounted receivers using liquid metals (sodium or a potassium/sodium mixture) as heat transport media. Sandia has successfully solar-tested a pool boiling reflux receiver sized to power a 25 kW Stirling engine. Boiling stability and transient operation were both excellent. This document describes these activities in detail and will outline plans for future development.

  9. Teardrop bladder: additional considerations

    International Nuclear Information System (INIS)

    Wechsler, R.J.; Brennan, R.E.

    1982-01-01

    Nine cases of teardrop bladder (TDB) seen at excretory urography are presented. In some of these patients, the iliopsoas muscles were at the upper limit of normal in size, and additional evaluation of the perivesical structures with computed tomography (CT) was necessary. CT demonstrated only hypertrophied muscles with or without perivesical fat. The psoas muscles and pelvic width were measured in 8 patients and compared with the measurements of a control group of males without TDB. Patients with TDB had large iliopsoas muscles and narrow pelves compared with the control group. The psoas muscle width/pelvic width ratio was significantly greater (p < 0.0005) in patients with TDB than in the control group, with values of 1.04 + 0.05 and 0.82 + 0.09, respectively. It is concluded that TDB is not an uncommon normal variant in black males. Both iliopsoas muscle hypertrophy and a narrow pelvis are factors that predispose a patient to TDB

  10. Sewage sludge additive

    Science.gov (United States)

    Kalvinskas, J. J.; Mueller, W. A.; Ingham, J. D. (Inventor)

    1980-01-01

    The additive is for a raw sewage treatment process of the type where settling tanks are used for the purpose of permitting the suspended matter in the raw sewage to be settled as well as to permit adsorption of the dissolved contaminants in the water of the sewage. The sludge, which settles down to the bottom of the settling tank is extracted, pyrolyzed and activated to form activated carbon and ash which is mixed with the sewage prior to its introduction into the settling tank. The sludge does not provide all of the activated carbon and ash required for adequate treatment of the raw sewage. It is necessary to add carbon to the process and instead of expensive commercial carbon, coal is used to provide the carbon supplement.

  11. Development And Test of A Digitally Steered Antenna Array for The Navigator GPS Receiver

    Science.gov (United States)

    Pinto, Heitor David; Valdez, Jennifer E.; Winternitz, Luke M. B.; Hassouneh, Munther A.; Price, Samuel R.

    2012-01-01

    Global Positioning System (GPS)-based navigation has become common for low-Earth orbit spacecraft as the signal environment is similar to that on the Earth s surface. The situation changes abruptly, however, for spacecraft whose orbital altitudes exceed that of the GPS constellation. Visibility is dramatically reduced and signals that are present may be very weak and more susceptible to interference. GPS receivers effective at these altitudes require increased sensitivity, which often requires a high-gain antenna. Pointing such an antenna can pose a challenge. One efficient approach to mitigate these problems is the use of a digitally steered antenna array. Such an antenna can optimally allocate gain toward desired signal sources and away from interferers. This paper presents preliminary results in the development and test of a digitally steered antenna array for the Navigator GPS research program at NASA s Goddard Space Flight Center. In particular, this paper highlights the development of an array and front-end electronics, the development and test of a real-time software GPS receiver, and implementation of three beamforming methods for combining the signals from the array. Additionally, this paper discusses the development of a GPS signal simulator which produces digital samples of the GPS L1C/A signals as they would be received by an arbitrary antenna array configuration. The simulator models transmitter and receiver dynamics, near-far and multipath interference, and has been a critical component in both the development and test of the GPS receiver. The GPS receiver system was tested with real and simulated GPS signals. Preliminary results show that performance improvement was achieved in both the weak signal and interference environments, matching analytical predictions. This paper summarizes our initial findings and discusses the advantages and limitations of the antenna array and the various beamforming methods.

  12. Experiences with a researcher-centric ELN† †Electronic supplementary information (ESI) available. See DOI: 10.1039/c4sc02128b Click here for additional data file.

    Science.gov (United States)

    Badiola, Katrina A.; Bird, Colin; Brocklesby, William S.; Casson, John; Chapman, Richard T.; Coles, Simon J.; Cronshaw, James R.; Fisher, Adam; Gloria, Danmar; Grossel, Martin C.; Hibbert, D. Brynn; Knight, Nicola; Mapp, Lucy K.; Marazzi, Luke; Matthews, Brian; Milsted, Andy; Minns, Russell S.; Mueller, Karl T.; Murphy, Kelly; Parkinson, Tim; Quinnell, Rosanne; Robinson, John S.; Robertson, Murray N.; Robins, Michael; Springate, Emma; Tizzard, Graham; Todd, Matthew H.; Williamson, Alice E.; Willoughby, Cerys; Yang, Erica; Ylioja, Paul M.

    2015-01-01

    Electronic Laboratory Notebooks (ELNs) are progressively replacing traditional paper books in both commercial research establishments and academic institutions. University researchers require specific features from ELNs, given the need to promote cross-institutional collaborative working, to enable the sharing of procedures and results, and to facilitate publication. The LabTrove ELN, which we use as our exemplar, was designed to be researcher-centric (i.e., not only aimed at the individual researcher's basic needs rather than to a specific institutional or subject or disciplinary agenda, but also able to be tailored because it is open source). LabTrove is being used in a heterogeneous set of academic laboratories, for a range of purposes, including analytical chemistry, X-ray studies, drug discovery and a biomaterials project. Researchers use the ELN for recording experiments, preserving data collected, and for project coordination. This perspective article describes the experiences of those researchers from several viewpoints, demonstrating how a web-based open source electronic notebook can meet the diverse needs of academic researchers. PMID:29308130

  13. Patrick Janot receives the CNRS silver medal

    CERN Multimedia

    2005-01-01

    Patrick Janot during the award ceremony. (Photo Schwemling, Paris) On 25 November, Patrick Janot of the CERN Physics Department received the CNRS silver medal for IN2P3 (Institut national de physique nucléaire et de physique des particules). This prize, one of the most prestigious awarded by the French research centre, is given to scientists for the 'originality, quality and importance of their work, as recognised both nationally and internationally'. Patrick Janot joined the ALEPH collaboration, one of the four experiments at LEP, then under construction, in 1987. First a CERN Fellow, he went on to work for the CNRS at LAL in 1989. Together with his team, he developed innovative algorithms for the reconstruction of events. This work and others earned him the bronze CNRS medal in 1993, which is awarded to scientists for their first achievements. In 1997, he became a permanent physicist at CERN, where he continued to work for ALEPH. He was appointed LEP scientific co-ordinator for the last two years of the ac...

  14. CERN safety expert receives international award

    CERN Multimedia

    2005-01-01

    On 18 December 2004, the President of the Swiss Electro-technical Committee, Martin Reichle (left), presented the award to Helmut Schönbacher. Helmut Schönbacher, of the Safety Commission at CERN, has received, the "1906 Award" of the International Electrotechnical Commission (IEC) for his standardisation work on the influence of ionizing radiation on insulating materials. From 1986 until 2004, Schönbacher was leader of a working group on radiation composed of internationally recognised experts. It edited standards of the IEC 60544 series on the determination of the effects of ionizing radiation on electrical insulating materials. The working group also edited three IEC Technical Reports on the determination of long-term radiation ageing in polymers. This standardisation work and long-term experience from CERN on the radiation ageing of materials also contributed to research coordination programmes of the International Atomic Energy Agency (IAEA). From 1968 until 1988, Schönbacher was a member of the Rad...

  15. Sensing of the atmospheric variation using Low Cost GNSS Receiver

    Science.gov (United States)

    Bramanto, Brian; Gumilar, Irwan; Sidiq, Teguh P.; Kuntjoro, Wedyanto; Tampubolon, Daniel A.

    2018-05-01

    As the GNSS signals transmitted through the atmosphere, they are delayed by interference of TEC (Total Electron Content) in the ionosphere and water vapor in the troposphere. By using inverse-problem, name GNSS Meteorology, those parameters can be obtained precisely and several researches has approved and supported that method. However, the geodetic GNSS receivers are relatively high cost (30,000 to 70,000 each) to be established on a regular and uniform network. This research aims to investigate the potential use of low cost GNSS receiver (less than 2,000) to observe the atmospheric dynamic both in ionosphere and troposphere. Results indicated that low cost GNSS receiver is a promising tools to sensing the atmospheric dynamic, however, further processing is needed to enhance the data quality. It is found that both of ionosphere and troposphere dynamic has diurnal periodic component.

  16. Additive lattice kirigami.

    Science.gov (United States)

    Castle, Toen; Sussman, Daniel M; Tanis, Michael; Kamien, Randall D

    2016-09-01

    Kirigami uses bending, folding, cutting, and pasting to create complex three-dimensional (3D) structures from a flat sheet. In the case of lattice kirigami, this cutting and rejoining introduces defects into an underlying 2D lattice in the form of points of nonzero Gaussian curvature. A set of simple rules was previously used to generate a wide variety of stepped structures; we now pare back these rules to their minimum. This allows us to describe a set of techniques that unify a wide variety of cut-and-paste actions under the rubric of lattice kirigami, including adding new material and rejoining material across arbitrary cuts in the sheet. We also explore the use of more complex lattices and the different structures that consequently arise. Regardless of the choice of lattice, creating complex structures may require multiple overlapping kirigami cuts, where subsequent cuts are not performed on a locally flat lattice. Our additive kirigami method describes such cuts, providing a simple methodology and a set of techniques to build a huge variety of complex 3D shapes.

  17. Additive Manufactured Superconducting Cavities

    Science.gov (United States)

    Holland, Eric; Rosen, Yaniv; Woolleet, Nathan; Materise, Nicholas; Voisin, Thomas; Wang, Morris; Mireles, Jorge; Carosi, Gianpaolo; Dubois, Jonathan

    Superconducting radio frequency cavities provide an ultra-low dissipative environment, which has enabled fundamental investigations in quantum mechanics, materials properties, and the search for new particles in and beyond the standard model. However, resonator designs are constrained by limitations in conventional machining techniques. For example, current through a seam is a limiting factor in performance for many waveguide cavities. Development of highly reproducible methods for metallic parts through additive manufacturing, referred to colloquially as 3D printing\\x9D, opens the possibility for novel cavity designs which cannot be implemented through conventional methods. We present preliminary investigations of superconducting cavities made through a selective laser melting process, which compacts a granular powder via a high-power laser according to a digitally defined geometry. Initial work suggests that assuming a loss model and numerically optimizing a geometry to minimize dissipation results in modest improvements in device performance. Furthermore, a subset of titanium alloys, particularly, a titanium, aluminum, vanadium alloy (Ti - 6Al - 4V) exhibits properties indicative of a high kinetic inductance material. This work is supported by LDRD 16-SI-004.

  18. Concentrated solar power generation using solar receivers

    Science.gov (United States)

    Anderson, Bruce N.; Treece, William Dean; Brown, Dan; Bennhold, Florian; Hilgert, Christoph

    2017-08-08

    Inventive concentrated solar power systems using solar receivers, and related devices and methods, are generally described. Low pressure solar receivers are provided that function to convert solar radiation energy to thermal energy of a working fluid, e.g., a working fluid of a power generation or thermal storage system. In some embodiments, low pressure solar receivers are provided herein that are useful in conjunction with gas turbine based power generation systems.

  19. RF subsystem design for microwave communication receivers

    Science.gov (United States)

    Bickford, W. J.; Brodsky, W. G.

    A system review of the RF subsystems of (IFF) transponders, tropscatter receivers and SATCOM receivers is presented. The quantity potential for S-band and X-band IFF transponders establishes a baseline requirement. From this, the feasibility of a common design for these and other receivers is evaluated. Goals are established for a GaAs MMIC (monolithic microwave integrated circuit) device and related local oscillator preselector and self-test components.

  20. Receiver function estimated by maximum entropy deconvolution

    Institute of Scientific and Technical Information of China (English)

    吴庆举; 田小波; 张乃铃; 李卫平; 曾融生

    2003-01-01

    Maximum entropy deconvolution is presented to estimate receiver function, with the maximum entropy as the rule to determine auto-correlation and cross-correlation functions. The Toeplitz equation and Levinson algorithm are used to calculate the iterative formula of error-predicting filter, and receiver function is then estimated. During extrapolation, reflective coefficient is always less than 1, which keeps maximum entropy deconvolution stable. The maximum entropy of the data outside window increases the resolution of receiver function. Both synthetic and real seismograms show that maximum entropy deconvolution is an effective method to measure receiver function in time-domain.

  1. Effects of Oxytocin Administration on Receiving Help.

    Science.gov (United States)

    Human, Lauren J; Woolley, Joshua D; Mendes, Wendy Berry

    2017-11-27

    Receiving help can be a "mixed blessing." Despite the many psychosocial benefits it can carry, it sometimes has negative psychological consequences, such as loss in self-esteem or enhanced guilt. It is, therefore, important to understand the factors that modify responses to receiving help from others. We explored the role of the hormone oxytocin (OT) on affective and social responses to receiving help, given the putative role of OT in social bonding and attunement. To this end, we manipulated whether help was received from a same-sex interaction partner (confederate) versus a control condition, crossed with a double-blind administration of intranasal OT (vs. placebo), and examined subjective and observer-rated participant responses to help. We observed significant interactions between OT and the help manipulation. In the placebo condition, receiving help from the interaction partner compared with the control condition had negative consequences, such that participants reported greater negative affect and came to view themselves and their interaction partners more negatively after interacting together on several tasks. What is important, however, is that OT administration buffered against these negative subjective responses to receiving help. Further, outside observers rated participants who received OT administration as expressing greater happiness and gratitude in response to help, relative to those who received placebo. In sum, in the context of receiving help from a stranger, oxytocin administration fostered more positive affective and social responses. (PsycINFO Database Record (c) 2017 APA, all rights reserved).

  2. Shipping/Receiving and Quality Control

    Data.gov (United States)

    Federal Laboratory Consortium — Shipping receiving, quality control, large and precise inspection and CMM machines. Coordinate Measuring Machines, including "scanning" probes, optical comparators,...

  3. Compressive Sensing for Spread Spectrum Receivers

    DEFF Research Database (Denmark)

    Fyhn, Karsten; Jensen, Tobias Lindstrøm; Larsen, Torben

    2013-01-01

    With the advent of ubiquitous computing there are two design parameters of wireless communication devices that become very important: power efficiency and production cost. Compressive sensing enables the receiver in such devices to sample below the Shannon-Nyquist sampling rate, which may lead...... the bit error rate performance is degraded by the subsampling in the CS-enabled receivers, this may be remedied by including quantization in the receiver model.We also study the computational complexity of the proposed receiver design under different sparsity and measurement ratios. Our work shows...

  4. Effective Length of a Receiving Antenna in a Streaming Plasma

    Czech Academy of Sciences Publication Activity Database

    Chugunov, Yu. V.; Fiala, Vladimír

    2006-01-01

    Roč. 54, č. 10 (2006), s. 2750-2756 ISSN 0018-926X R&D Projects: GA AV ČR IAA301120601 Institutional research plan: CEZ:AV0Z30420517 Keywords : receiving antenna * plasma waves * resonance Subject RIV: BL - Plasma and Gas Discharge Physics Impact factor: 1.480, year: 2006

  5. Production response of lambs receiving creep feed while grazing ...

    African Journals Online (AJOL)

    The aim of the study was to determine the production responses of lambs receiving either creep feed or not while grazing two different pastures. The production of ewes within each treatment was also recorded. The study was conducted at both the Kromme Rhee and Langgewens Research Farms. At Kromme Rhee, sheep ...

  6. Simulation of the MRS receiving and handling facility

    International Nuclear Information System (INIS)

    Triplett, M.B.; Imhoff, C.H.; Hostick, C.J.

    1984-02-01

    Monitored retrievable storage (MRS) will be required to handle a large volume of spent fuel or high-level waste (HLW) in case of delays in repository deployment. The quantities of materials to be received and repackaged for storage far exceed the requirements of existing waste mangement facilities. A computer simulation model of the MRS receiving and handling (R and H) fcility has been constructed and used to evaluate design alternatives. Studies have identified processes or activities which may constrain throughput performance. In addition, the model has helped to assess design tradeoffs such as those to be made among improved process times, redundant service lines, and improved component availability. 1 reference, 5 figures

  7. 3D-RTK Capability of Single Gnss Receivers

    Science.gov (United States)

    Stempfhuber, W.

    2013-08-01

    Small, aerial objects are now being utilised in many areas of civil object capture and monitoring. As a rule, the standard application of a simple GPS receiver with code solutions serves the 3D-positioning of the trajectories or recording positions. Without GPS correction information, these can be calculated at an accuracy of 10-20 metres. Corrected code solutions (DGPS) generally lie in the metre range. A precise 3D-positioning of the UAV (unmanned aerial vehicle) trajectories in the centimetre range provides significant improvements. In addition, the recording time of each sensor can be synchronized with the exact time stamp of the GNSS low-cost system. In recent years, increasing works on positioning from L1 GPS raw data have been published. Along with this, the carrier phase measurements with the established evaluation algorithms are analysed in the post processing method to centimetre-exact positions or to high-precision 3D trajectories [e.g. Schwieger and Gläser, 2005 or Korth and Hofmann 20011]. The use of reference information from local reference stations or a reference network serves the purpose of carrier phase ambiguity resolution. Furthermore, there are many activities worldwide in the area of PPP techniques (Precise Point Positioning). However, dual frequency receivers are primarily used in this instance. Moreover, very long initialisation times must be scheduled for this. A research project on the subject of low-cost RTK GNSS was developed for real-time applications at the Beuth Hochschule für Technik Berlin University of Applied Sciences [Stempfhuber 2012]. The overall system developed for the purpose of real-time applications with centimetre accuracy is modularly constructed and can be used for various applications (http://prof.beuthhochschule.de/stempfhuber/seite-publikation/). With hardware costing a few hundred Euro and a total weight of 500-800 g (including the battery), this system is ideally suited for UAV applications. In addition, the

  8. ALICE physicists receive 2014 Lise Meitner Prize

    CERN Multimedia

    Katarina Anthony

    2014-01-01

    On Wednesday, 3 September, four ALICE physicists were presented with the European Physical Society's 2014 Lise Meitner Prize for their outstanding contributions to nuclear physics (see here).   ALICE collaboration members Johanna Stachel (Heidelberg University, Germany), Peter Braun-Munzinger (GSI, Germany), Paolo Giubellino (INFN Turin, Italy, and CERN) and Jürgen Schukraft (CERN) were presented with their awards at a private ceremony held in the Globe of Science and Innovation. In addition to members of the ALICE collaboration, the ceremony was attended by members of the CERN Management including the Director-General, Rolf Heuer, as well as the EPS Nuclear Physics Board Chair, Douglas MacGregor, and the EPS Lise Meitner Prize Committee Chair, Victor Zamfir. For more information, please see "EPS honours CERN's heavy-ion researchers".  From left to right: Douglas MacGregor (EPS); Prize recipients Jürgen Schukraft,&a...

  9. Analysis of signal acquisition in GPS receiver software

    Directory of Open Access Journals (Sweden)

    Vlada S. Sokolović

    2011-01-01

    Full Text Available This paper presents a critical analysis of the flow signal processing carried out in GPS receiver software, which served as a basis for a critical comparison of different signal processing architectures within the GPS receiver. It is possible to achieve Increased flexibility and reduction of GPS device commercial costs, including those of mobile devices, by using radio technology software (SDR, Software Defined Radio. The SDR application can be realized when certain hardware components in a GPS receiver are replaced. Signal processing in the SDR is implemented using a programmable DSP (Digital Signal Processing or FPGA (Field Programmable Gate Array circuit, which allows a simple change of digital signal processing algorithms and a simple change of the receiver parameters. The starting point of the research is the signal generated on the satellite the structure of which is shown in the paper. Based on the GPS signal structure, a receiver is realized with a task to extract an appropriate signal from the spectrum and detect it. Based on collected navigation data, the receiver calculates the position of the end user. The signal coming from the satellite may be at the carrier frequencies of L1 and L2. Since the SPS is used in the civil service, all the tests shown in the work were performed on the L1 signal. The signal coming to the receiver is generated in the spread spectrum technology and is situated below the level of noise. Such signals often interfere with signals from the environment which presents a difficulty for a receiver to perform proper detection and signal processing. Therefore, signal processing technology is continually being improved, aiming at more accurate and faster signal processing. All tests were carried out on a signal acquired from the satellite using the SE4110 input circuit used for filtering, amplification and signal selection. The samples of the received signal were forwarded to a computer for data post processing, i. e

  10. Implementation of the Additional Protocol in Japan

    International Nuclear Information System (INIS)

    Ogawa, T.

    2001-01-01

    The Additional Protocol between Japan and the IAEA entered into force in December 1999. To come into force a series of implementation trials of Additional Protocol was carried out at two Japanese representative nuclear research centers, i.e. Tokai Research Establishment of Japan Atomic Energy Research Institute (JAERI) and Oarai Engineering Center of Japan Nuclear Fuel Cycle Development Institute (JNC). These trials were proposed by Japan and were conducted in cooperation with the IAEA Secretariat. In addition, Japan amended 'the Law for the Regulation of Reactors etc.', to collect adequate information to submit to the IAEA, to arrange the surrounding for the complementary access, etc. In addition, Japan Submitted the Initial Declaration of the Additional Protocol within 180 days of the entry into force of the Protocol, in the middle of June, 2000

  11. Additive Manufacturing of Magnesium (Mg) Alloys

    Data.gov (United States)

    National Aeronautics and Space Administration — The proposed work is to investigate additive manufacturing techniques for Mg alloys.  It will leverage off research being conducted at University of Florida and...

  12. An SDR based AIS receiver for satellites

    DEFF Research Database (Denmark)

    Larsen, Jesper Abildgaard; Mortensen, Hans Peter; Nielsen, Jens Frederik Dalsgaard

    2011-01-01

    For a few years now, there has been a high interest in monitoring the global ship traffic from space. A few satellite, capable of listening for ship borne AIS transponders have already been launched, and soon the AAUSAT3, carrying two different types of AIS receivers will also be launched. One...... of the AIS receivers onboard AAUSAT3 is an SDR based AIS receiver. This paper serves to describe the background of the AIS system, and how the SDR based receiver has been integrated into the AAUSAT3 satellite. Amongst some of the benefits of using an SDR based receiver is, that due to its versatility, new...... detection algorithms are easily deployed, and it is easily adapted the new proposed AIS transmission channels....

  13. Heat receiving plates in thermonuclear device

    International Nuclear Information System (INIS)

    Kitamura, Kazunori.

    1988-01-01

    Purpose: To obtain a heat receiving plate structure capable of withstanding sputtering wear and retaining the thermal deformation and residual stress low upon junction and available at a reduced cost. Constitution: Junction structures between heat sinks and armours are the same as usual, whereas high melting armour (for example, made of tungsten) are used at the portion on a heat receiving plate where the thermal load and particle load are higher while materials having a heat expansion coefficient similar to that of the heat sink (stainless steel) are used at the portion where the thermal load and particle load are lower on a heat receiving plate depending on the thermal load and particle load distribution. This can reduce the thermal deformation for the entire divertor heat receiving plate to obtain a heat receiving plate of a good surface dimensional accuracy. (Takahashi, M.)

  14. High thermal load receiving heat plate

    International Nuclear Information System (INIS)

    Shibutani, Jun-ichi; Shibayama, Kazuhito; Yamamoto, Keiichi; Uchida, Takaho.

    1993-01-01

    The present invention concerns a high thermal load heat receiving plate such as a divertor plate of a thermonuclear device. The high thermal load heat receiving plate of the present invention has a cooling performance capable of suppressing the temperature of an armour tile to less than a threshold value of the material against high thermal loads applied from plasmas. Spiral polygonal pipes are inserted in cooling pipes at a portion receiving high thermal loads in the high temperature load heat receiving plate of the present invention. Both ends of the polygonal pipes are sealed by lids. An area of the flow channel in the cooling pipes is thus reduced. Heat conductivity on the cooling surface of the cooling pipes is increased in the high thermal load heat receiving plate having such a structure. Accordingly, temperature elevation of the armour tile can be suppressed. (I.S.)

  15. Laser polishing of additive manufactured Ti alloys

    Science.gov (United States)

    Ma, C. P.; Guan, Y. C.; Zhou, W.

    2017-06-01

    Laser-based additive manufacturing has attracted much attention as a promising 3D printing method for metallic components in recent years. However, surface roughness of additive manufactured components has been considered as a challenge to achieve high performance. In this work, we demonstrate the capability of fiber laser in polishing rough surface of additive manufactured Ti-based alloys as Ti-6Al-4V and TC11. Both as-received surface and laser-polished surfaces as well as cross-section subsurfaces were analyzed carefully by White-Light Interference, Confocal Microscope, Focus Ion Beam, Scanning Electron Microscopy, Energy Dispersive Spectrometer, and X-ray Diffraction. Results revealed that as-received Ti-based alloys with surface roughness more than 5 μm could be reduce to less than 1 μm through laser polishing process. Moreover, microstructure, microhardness and wear resistance of laser-polished zone was investigated in order to examine the thermal effect of laser polishing processing on the substrate of additive manufactured Ti alloys. This proof-of-concept process has the potential to effectively improve the surface roughness of additive manufactured metallic alloy by local polishing method without damage to the substrate.

  16. Fundamentals of GPS Receivers A Hardware Approach

    CERN Document Server

    Doberstein, Dan

    2012-01-01

    While much of the current literature on GPS receivers is aimed at those intimately familiar with their workings, this volume summarizes the basic principles using as little mathematics as possible, and details the necessary specifications and circuits for constructing a GPS receiver that is accurate to within 300 meters. Dedicated sections deal with the features of the GPS signal and its data stream, the details of the receiver (using a hybrid design as exemplar), and more advanced receivers and topics including time and frequency measurements. Later segments discuss the Zarlink GPS receiver chip set, as well as providing a thorough examination of the TurboRogue receiver, one of the most accurate yet made. Guiding the reader through the concepts and circuitry, from the antenna to the solution of user position, the book’s deployment of a hybrid receiver as a basis for discussion allows for extrapolation of the core ideas to more complex, and more accurate designs. Digital methods are used, but any analogue c...

  17. GPU Acceleration of DSP for Communication Receivers.

    Science.gov (United States)

    Gunther, Jake; Gunther, Hyrum; Moon, Todd

    2017-09-01

    Graphics processing unit (GPU) implementations of signal processing algorithms can outperform CPU-based implementations. This paper describes the GPU implementation of several algorithms encountered in a wide range of high-data rate communication receivers including filters, multirate filters, numerically controlled oscillators, and multi-stage digital down converters. These structures are tested by processing the 20 MHz wide FM radio band (88-108 MHz). Two receiver structures are explored: a single channel receiver and a filter bank channelizer. Both run in real time on NVIDIA GeForce GTX 1080 graphics card.

  18. Global Positioning System receiver evaluation results

    Energy Technology Data Exchange (ETDEWEB)

    Byrne, R.H.

    1993-09-01

    A Sandia project currently uses an outdated Magnavox 6400 Global Positioning System (GPS) receiver as the core of its navigation system. The goal of this study was to analyze the performance of the current GPS receiver compared to newer, less expensive models and to make recommendations on how to improve the performance of the overall navigation system. This paper discusses the test methodology used to experimentally analyze the performance of different GPS receivers, the test results, and recommendations on how an upgrade should proceed. Appendices contain detailed information regarding the raw data, test hardware, and test software.

  19. Decoding algorithm for vortex communications receiver

    Science.gov (United States)

    Kupferman, Judy; Arnon, Shlomi

    2018-01-01

    Vortex light beams can provide a tremendous alphabet for encoding information. We derive a symbol decoding algorithm for a direct detection matrix detector vortex beam receiver using Laguerre Gauss (LG) modes, and develop a mathematical model of symbol error rate (SER) for this receiver. We compare SER as a function of signal to noise ratio (SNR) for our algorithm and for the Pearson correlation algorithm. To our knowledge, this is the first comprehensive treatment of a decoding algorithm of a matrix detector for an LG receiver.

  20. Exploiting Redundancy in an OFDM SDR Receiver

    Directory of Open Access Journals (Sweden)

    Tomas Palenik

    2009-01-01

    Full Text Available Common OFDM system contains redundancy necessary to mitigate interblock interference and allows computationally effective single-tap frequency domain equalization in receiver. Assuming the system implements an outer error correcting code and channel state information is available in the receiver, we show that it is possible to understand the cyclic prefix insertion as a weak inner ECC encoding and exploit the introduced redundancy to slightly improve error performance of such a system. In this paper, an easy way to implement modification to an existing SDR OFDM receiver is presented. This modification enables the utilization of prefix redundancy, while preserving full compatibility with existing OFDM-based communication standards.

  1. Wide-band coherent receiver development for enhanced surveillance

    International Nuclear Information System (INIS)

    Simpson, M.L.; Richards, R.K.; Hutchinson, D.P.

    1998-03-01

    Oak Ridge National Laboratory (ORNL) has been developing advanced coherent IR heterodyne receivers for plasma diagnostics in fusion reactors for over 20 years. Recent progress in wide band IR detectors and high speed electronics has significantly enhanced the measurement capabilities of coherent receivers. In addition, developments in new HgCdTe and quantum well IR photodetector (QWIP) focal plane arrays are providing the possibility of both active and passive coherent imaging. In this paper the authors discuss the implications of these new enabling technologies to the IR remote sensing community for enhanced surveillance. Coherent receivers, as opposed to direct or thermal detection, provide multiple dimensions of information about a scene or target in a single detector system. Combinations of range, velocity, temperature, and chemical species information are all available from a coherent heterodyne receiver. They present laboratory data showing measured noise equivalent power (NEP) of new QWIP detectors with heterodyne bandwidths greater than 7 GHz. For absorption measurements, a wide band coherent receiver provides the capability of looking between CO 2 lines at off-resonance peaks and thus the measurement of lines normally inaccessible with conventional heterodyne or direct detection systems. Also described are differential absorption lidar (DIAL) and Doppler laboratory measurements using an 8 x 8 HgCdTe focal plane array demonstrating the snapshot capability of coherent receiver detector arrays for enhanced chemical plume and moving hardbody capture. Finally they discuss a variety of coherent receiver configurations that can suppress (or enhance) sensitivity of present active remote sensing systems to speckle, glint, and other measurement anomalies

  2. Software for Adapting Dspz Receivers to the Uran Interferometer Network

    Science.gov (United States)

    Isaeva, E. A.; Lytvynenko, O. A.; Shepelev, V. A.

    More than 10 years ago, URAN interferometer network (Megn A.V.,1997; Konovalenko A.A., 2014) had been equipped with newly designed receivers with a pass band extended up to 250 kHz and software rejection of interferences (Rashkovskii, 2012). The broadening of bandwidth of received signal increase the sensitivity of the receivers significantly and let us to investigate the angular structure about one hundred radio sources. A software package had been developed that allows: preparing a program of observations, carrying out observations automatically, making data cross-correlation, calculating visibility functions for all pairs of antennae, and fitting models of an angular structure of the sources. Data storage formats were elaborated for each stage of recording or processing. At present, new digital radio astronomy receiver DSPZ have been developed by IRA NASU (Zakharenko, 2016). The receiver allows recording an entire bandwidth of signals of a decameter range from 8 to 32 MHz. It is used at UTR-2 and URAN radio telescopes operated in a single dish mode. Application of the receivers for interferometer observation with the URAN network provides additional advantages in accuracy and sensitivity of studies. In this report we consider the data formats and synchronization methods used in URAN equipment and DSPZ receivers, and discuss algorithms of their transformation. Newly elaborated software is described, that allows selecting a set of frequency bands of signals recorded with DSPZ and converting them to the form used by the URAN software. This approach allows us to carry out the interferometer observations in an the extended frequency range provided by DSPZ and to use as much as possible the software package developed for the URAN network for data reduction.

  3. Smooth time-dependent receiver operating characteristic curve estimators.

    Science.gov (United States)

    Martínez-Camblor, Pablo; Pardo-Fernández, Juan Carlos

    2018-03-01

    The receiver operating characteristic curve is a popular graphical method often used to study the diagnostic capacity of continuous (bio)markers. When the considered outcome is a time-dependent variable, two main extensions have been proposed: the cumulative/dynamic receiver operating characteristic curve and the incident/dynamic receiver operating characteristic curve. In both cases, the main problem for developing appropriate estimators is the estimation of the joint distribution of the variables time-to-event and marker. As usual, different approximations lead to different estimators. In this article, the authors explore the use of a bivariate kernel density estimator which accounts for censored observations in the sample and produces smooth estimators of the time-dependent receiver operating characteristic curves. The performance of the resulting cumulative/dynamic and incident/dynamic receiver operating characteristic curves is studied by means of Monte Carlo simulations. Additionally, the influence of the choice of the required smoothing parameters is explored. Finally, two real-applications are considered. An R package is also provided as a complement to this article.

  4. Graphene integrated circuits: new prospects towards receiver realisation.

    Science.gov (United States)

    Saeed, Mohamed; Hamed, Ahmed; Wang, Zhenxing; Shaygan, Mehrdad; Neumaier, Daniel; Negra, Renato

    2017-12-21

    This work demonstrates a design approach which enables the fabrication of fully integrated radio frequency (RF) and millimetre-wave frequency direct-conversion graphene receivers by adapting the frontend architecture to exploit the state-of-the-art performance of the recently reported wafer-scale CVD metal-insulator-graphene (MIG) diodes. As a proof-of-concept, we built a fully integrated microwave receiver in the frequency range 2.1-2.7 GHz employing the strong nonlinearity and the high responsivity of MIG diodes to successfully receive and demodulate complex, digitally modulated communication signals at 2.45 GHz. In addition, the fabricated receiver uses zero-biased MIG diodes and consumes zero dc power. With the flexibility to be fabricated on different substrates, the prototype receiver frontend is fabricated on a low-cost, glass substrate utilising a custom-developed MMIC process backend which enables the high performance of passive components. The measured performance of the prototype makes it suitable for Internet-of-Things (IoT) and Radio Frequency Identification (RFID) systems for medical and communication applications.

  5. Mechanics of additively manufactured biomaterials.

    Science.gov (United States)

    Zadpoor, Amir A

    2017-06-01

    Additive manufacturing (3D printing) has found many applications in healthcare including fabrication of biomaterials as well as bioprinting of tissues and organs. Additively manufactured (AM) biomaterials may possess arbitrarily complex micro-architectures that give rise to novel mechanical, physical, and biological properties. The mechanical behavior of such porous biomaterials including their quasi-static mechanical properties and fatigue resistance is not yet well understood. It is particularly important to understand the relationship between the designed micro-architecture (topology) and the resulting mechanical properties. The current special issue is dedicated to understanding the mechanical behavior of AM biomaterials. Although various types of AM biomaterials are represented in the special issue, the primary focus is on AM porous metallic biomaterials. As a prelude to this special issue, this editorial reviews some of the latest findings in the mechanical behavior of AM porous metallic biomaterials so as to describe the current state-of-the-art and set the stage for the other studies appearing in the issue. Some areas that are important for future research are also briefly mentioned. Copyright © 2017 Elsevier Ltd. All rights reserved.

  6. 45 CFR 2530.60 - What is the impact of transferring or receiving a transferred education award on an individual's...

    Science.gov (United States)

    2010-10-01

    ... transferred education award on an individual's eligibility to receive additional education awards? 2530.60... AND COMMUNITY SERVICE TRANSFER OF EDUCATION AWARDS § 2530.60 What is the impact of transferring or receiving a transferred education award on an individual's eligibility to receive additional education...

  7. Thermal characteristics of tubular receivers of solar radiation line concentrators

    International Nuclear Information System (INIS)

    Klychev, Sh.I.; Zakhidov, R.A.; Khuzhanov, R. et al.

    2013-01-01

    A stationary thermal model of an LCS-HR system is considered, taking into account the basic parameters of the problem: availability of a transparent screen, selectivity of the receiver, characteristics of the heat carrier and average concentration on the surface of the tubular receiver C"". Based on this model, an algorithm and program of numerical research of the thermal characteristics of the HR-temperature of heating and local and average coefficients of efficiency are developed. For possible concentrations, the selectivity of the receiver and the transparency of the screen in linear concentrators, the potential stationary heating temperatures, and the coefficients of efficiency for main three types of heat carriers - air, water, and liquid metal coolant are studied. The time of achieving stationary values by the temperatures of the heat carrier is estimated. (author)

  8. 29 CFR 1926.306 - Air receivers.

    Science.gov (United States)

    2010-07-01

    ... transportation vehicles such as steam railroad cars, electric railway cars, and automotive equipment. (2) New and... manholes therein are easily accessible. Under no circumstances shall an air receiver be buried underground...

  9. 29 CFR 1910.169 - Air receivers.

    Science.gov (United States)

    2010-07-01

    ... and equipment used on transportation vehicles such as steam railroad cars, electric railway cars, and... therein are easily accessible. Under no circumstances shall an air receiver be buried underground or...

  10. 47 CFR 32.1170 - Receivables.

    Science.gov (United States)

    2010-10-01

    ... FOR TELECOMMUNICATIONS COMPANIES Instructions for Balance Sheet Accounts § 32.1170 Receivables. (a... of interest accrued to the date of the balance sheet on bonds, notes, and other commercial paper...

  11. Optical Coherent Receiver Enables THz Wireless Bridge

    DEFF Research Database (Denmark)

    Yu, Xianbin; Liu, Kexin; Zhang, Hangkai

    2016-01-01

    We experimentally demonstrated a 45 Gbit/s 400 GHz photonic wireless communication system enabled by an optical coherent receiver, which has a high potential in fast recovery of high data rate connections, for example, in disaster....

  12. Storage rack for fuel cell receiving shrouds

    International Nuclear Information System (INIS)

    Mollon, L.

    1978-01-01

    Disclosed is a rack for receiving a multiplicity of vertical tubular shrouds or tubes for storing spent nuclear fuel cells. The rack comprises a plurality of horizontally reticulated frames interconnected by tension rods and spacing tubes surrounding the rods

  13. List of Nuclear Materials Licensing Actions Received

    Data.gov (United States)

    Nuclear Regulatory Commission — A catalog of all Materials Licensing Actions received for review. The catalog lists the name of the entity submitting the license application, their city and state,...

  14. X-radiation from television receivers and video display terminals

    International Nuclear Information System (INIS)

    Huang, Ching-Chung; Lin, Pei-Huo; Lin, Yu-Ming; Weng, Pao-Shan.

    1986-01-01

    This paper deals with the X-radiation from television receivers and video display terminals. The bremsstrahlung production rate was calculated according to the thick target theory, and the transmitted X-radiation was measured by the spectrometry method. The calculated and the measured results were compared and discussed. In addition, evidences were shown that only the highest energy component of the bremsstrahlung can penetrate the cathode ray tube. (author)

  15. Single-Receiver GPS Phase Bias Resolution

    Science.gov (United States)

    Bertiger, William I.; Haines, Bruce J.; Weiss, Jan P.; Harvey, Nathaniel E.

    2010-01-01

    Existing software has been modified to yield the benefits of integer fixed double-differenced GPS-phased ambiguities when processing data from a single GPS receiver with no access to any other GPS receiver data. When the double-differenced combination of phase biases can be fixed reliably, a significant improvement in solution accuracy is obtained. This innovation uses a large global set of GPS receivers (40 to 80 receivers) to solve for the GPS satellite orbits and clocks (along with any other parameters). In this process, integer ambiguities are fixed and information on the ambiguity constraints is saved. For each GPS transmitter/receiver pair, the process saves the arc start and stop times, the wide-lane average value for the arc, the standard deviation of the wide lane, and the dual-frequency phase bias after bias fixing for the arc. The second step of the process uses the orbit and clock information, the bias information from the global solution, and only data from the single receiver to resolve double-differenced phase combinations. It is called "resolved" instead of "fixed" because constraints are introduced into the problem with a finite data weight to better account for possible errors. A receiver in orbit has much shorter continuous passes of data than a receiver fixed to the Earth. The method has parameters to account for this. In particular, differences in drifting wide-lane values must be handled differently. The first step of the process is automated, using two JPL software sets, Longarc and Gipsy-Oasis. The resulting orbit/clock and bias information files are posted on anonymous ftp for use by any licensed Gipsy-Oasis user. The second step is implemented in the Gipsy-Oasis executable, gd2p.pl, which automates the entire process, including fetching the information from anonymous ftp

  16. Flexible receiver adapter formal design review

    International Nuclear Information System (INIS)

    Krieg, S.A.

    1995-01-01

    This memo summarizes the results of the Formal (90%) Design Review process and meetings held to evaluate the design of the Flexible Receiver Adapters, support platforms, and associated equipment. The equipment is part of the Flexible Receiver System used to remove, transport, and store long length contaminated equipment and components from both the double and single-shell underground storage tanks at the 200 area tank farms

  17. Anatomy of a digital coherent receiver

    DEFF Research Database (Denmark)

    Borkowski, Robert; Zibar, Darko; Tafur Monroy, Idelfonso

    2014-01-01

    , orthonormaliation, chromatic dispersion compensation/nonlinear compensation, resampling a nd timing recovery, polarization demultiplexing and equalization, frequency and phase recovery, digital demodulation. We also describe novel subsystems of a digital coherent receiver: modulation format recognition......Digital coherent receivers have gained significant attention in the last decade. The reason for this is that coherent detection, along with digital signal processing (DSP) allows for substantial increase of the channel capacity by employing advanced detection techniques. In this paper, we first...

  18. How health information is received by diabetic patients?

    Directory of Open Access Journals (Sweden)

    Firoozeh Zare-Farashbandi

    2015-01-01

    Full Text Available Background: Knowledge of correct information-seeking behavior by the patients can provide health specialists and health information specialists with valuable information in improving health care. This study aimed to investigate the passive receipt and active seeking of health information by diabetic patients. Materials and Methods: A survey method was used in this research on 6426 diabetic patients of whom 362 patients were selected by a no percentage stratified random sampling. The Longo information-seeking behavior questionnaire was used to collect data and they were analyzed by SPSS 20 software. Results: The most common information source by diabetic patients was practitioners (3.12. The minimum usage among the information sources were from charity organizations and emergency phone lines with a usage of close to zero. The amount of health information gained passively from each source has the lowest average of 4.18 and usage of this information in making health decision has the highest average score of 5.83. Analysis of the data related to active seeking of information showed that knowledge of available medical information from each source has the lowest average score of 3.95 and ability in using the acquired information for making medical decisions has the highest average score of 5.28. The paired t-test showed that differences between passive information receipt (41.68 and active information seeking (39.20 considered as statistically significant (P < 0.001. Conclusion: Because diabetic patients are more passive information receivers than active information seekers, the health information must be distributed by passive means to these patients. In addition, information-seeking behavior during different time periods should be investigated; to identify more effective distribution of health information.

  19. Efficient receiver tuning using differential evolution strategies

    Science.gov (United States)

    Wheeler, Caleb H.; Toland, Trevor G.

    2016-08-01

    Differential evolution (DE) is a powerful and computationally inexpensive optimization strategy that can be used to search an entire parameter space or to converge quickly on a solution. The Kilopixel Array Pathfinder Project (KAPPa) is a heterodyne receiver system delivering 5 GHz of instantaneous bandwidth in the tuning range of 645-695 GHz. The fully automated KAPPa receiver test system finds optimal receiver tuning using performance feedback and DE. We present an adaptation of DE for use in rapid receiver characterization. The KAPPa DE algorithm is written in Python 2.7 and is fully integrated with the KAPPa instrument control, data processing, and visualization code. KAPPa develops the technologies needed to realize heterodyne focal plane arrays containing 1000 pixels. Finding optimal receiver tuning by investigating large parameter spaces is one of many challenges facing the characterization phase of KAPPa. This is a difficult task via by-hand techniques. Characterizing or tuning in an automated fashion without need for human intervention is desirable for future large scale arrays. While many optimization strategies exist, DE is ideal for time and performance constraints because it can be set to converge to a solution rapidly with minimal computational overhead. We discuss how DE is utilized in the KAPPa system and discuss its performance and look toward the future of 1000 pixel array receivers and consider how the KAPPa DE system might be applied.

  20. Performance Evaluation of Irbene RT-16 Radio Telescope Receiving System

    Directory of Open Access Journals (Sweden)

    Bleiders M.

    2017-12-01

    Full Text Available In the present paper, recent measurement results of refurbished Irbene RT-16 radio telescope receiving system performance are presented. The aim of the research is to evaluate characteristics of RT-16, which will allow carrying out necessary amplitude calibration in both single dish and VLBI observations, to improve the performance of existing system as well as to monitor, control and compare performance if possible changes in the receiving system will occur in future. The evaluated receiving system is 16 m Cassegrain antenna equipped with a cryogenic receiver with frequency range from 4.5 to 8.8 GHz, which is divided into four sub-bands. Multiple calibration sessions have been carried out by observing stable astronomical sources with known flux density by using in-house made total power registration backend. First, pointing offset calibration has been carried out and pointing model coefficients calculated and applied. Then, amplitude calibration, namely antenna sensitivity, calibration diode equivalent flux density and gain curve measurements have been carried out by observing calibration sources at different antenna elevations at each of the receiver sub-bands. Beam patterns have also been evaluated at different frequency bands. As a whole, acquired data will serve as a reference point for comparison in future performance evaluation of RT-16.

  1. Quad channel software defined receiver for passive radar application

    Directory of Open Access Journals (Sweden)

    Pető Tamás

    2017-03-01

    Full Text Available In recent times the growing utilization of the electromagnetic environment brings the passive radar researches more and more to the fore. For the utilization of the wide range of illuminators of opportunity the application of wideband radio receivers is required. At the same time the multichannel receiver structure has also critical importance in target direction finding and interference suppression. This paper presents the development of a multichannel software defined receiver specifically for passive radar applications. One of the relevant feature of the developed receiver platform is its up-to-date SoC (System on hip based structure, which greatly enhance the integration and signal processing capacity of the system, all while keeping the costs low. The software defined operation of the discussed receiver system is demonstrated with using DVB-T (Digital Video Broadcast – Terrestrial signal as illuminator of opportunity. During this demonstration the multichannel capabilities of the realized system are also tested with real data using direction finding and beamforming algorithms.

  2. Distributed sensing of ionospheric irregularities with a GNSS receiver array

    Science.gov (United States)

    Su, Yang; Datta-Barua, Seebany; Bust, Gary S.; Deshpande, Kshitija B.

    2017-08-01

    We present analysis methods for studying the structuring and motion of ionospheric irregularities at the subkilometer scale sizes that produce L band scintillations. Spaced-receiver methods are used for Global Navigation Satellite System (GNSS) receivers' phase measurements over approximately subkilometer to kilometer length baselines for the first time. The quantities estimated by these techniques are plasma drift velocity, diffraction anisotropy magnitude and orientation, and characteristic velocity. Uncertainties are quantified by ensemble simulation of noise on the phase signals carried through to the observations of the spaced-receiver linear system. These covariances are then propagated through to uncertainties on drifts through linearization about the estimated values of the state. Five receivers of SAGA, the Scintillation Auroral Global Positioning System (GPS) Array, provide 100 Hz power and phase data for each channel at L1 frequency. The array is sited in the auroral zone at Poker Flat Research Range, Alaska. A case study of a single scintillating satellite observed by the array is used to demonstrate the spaced-receiver and uncertainty estimation process. A second case study estimates drifts as measured by multiple scintillating channels. These scintillations are correlated with auroral activity, based on all-sky camera images. Measurements and uncertainty estimates made over a 30 min period are compared to a collocated incoherent scatter radar and show good agreement in horizontal drift speed and direction during periods of scintillation for which the characteristic velocity is less than the drift velocity.

  3. Thermal State-of-Charge in Solar Heat Receivers

    Science.gov (United States)

    Hall, Carsie, A., III; Glakpe, Emmanuel K.; Cannon, Joseph N.; Kerslake, Thomas W.

    1998-01-01

    A theoretical framework is developed to determine the so-called thermal state-of-charge (SOC) in solar heat receivers employing encapsulated phase change materials (PCMS) that undergo cyclic melting and freezing. The present problem is relevant to space solar dynamic power systems that would typically operate in low-Earth-orbit (LEO). The solar heat receiver is integrated into a closed-cycle Brayton engine that produces electric power during sunlight and eclipse periods of the orbit cycle. The concepts of available power and virtual source temperature, both on a finite-time basis, are used as the basis for determining the SOC. Analytic expressions for the available power crossing the aperture plane of the receiver, available power stored in the receiver, and available power delivered to the working fluid are derived, all of which are related to the SOC through measurable parameters. Lower and upper bounds on the SOC are proposed in order to delineate absolute limiting cases for a range of input parameters (orbital, geometric, etc.). SOC characterization is also performed in the subcooled, two-phase, and superheat regimes. Finally, a previously-developed physical and numerical model of the solar heat receiver component of NASA Lewis Research Center's Ground Test Demonstration (GTD) system is used in order to predict the SOC as a function of measurable parameters.

  4. An analysis of referrals received by a psychiatric unit in a general ...

    African Journals Online (AJOL)

    An analysis of referrals received by a psychiatric unit in a general hospital part 1: the need for and research design adopted to study referrals received by a psychiatric unit in a general hospital: research. M. Dor, V.J. Ehlers, M.M. Van der Merwe ...

  5. EXAMINE AND EVALUATE A PROCESS TO USE SALT CAVERNS TO RECEIVE SHIP BORNE LIQUEFIED NATURAL GAS

    Energy Technology Data Exchange (ETDEWEB)

    Michael M. McCall; William M. Bishop; D. Braxton Scherz

    2003-04-24

    The goal of the U.S. Department of Energy cooperative research project is to define, describe, and validate, a process to utilize salt caverns to receive and store the cargoes of LNG ships. The project defines the process as receiving LNG from a ship, pumping the LNG up to cavern injection pressures, warming it to cavern compatible temperatures, injecting the warmed vapor directly into salt caverns for storage, and distribution to the pipeline network. The performance of work under this agreement is based on U.S. Patent 5,511,905, and other U.S. and Foreign pending patent applications. The cost sharing participants in the research are The National Energy Technology Laboratory (U.S. Department of Energy), BP America Production Company, Bluewater Offshore Production Systems (U.S.A.), Inc., and HNG Storage, L.P. Initial results indicate that a salt cavern based receiving terminal could be built at about half the capital cost, less than half the operating costs and would have significantly higher delivery capacity, shorter construction time, and be much more secure than a conventional liquid tank based terminal. There is a significant body of knowledge and practice concerning natural gas storage in salt caverns, and there is a considerable body of knowledge and practice in handling LNG, but there has never been any attempt to develop a process whereby the two technologies can be combined. Salt cavern storage is infinitely more secure than surface storage tanks, far less susceptible to accidents or terrorist acts, and much more acceptable to the community. The project team developed conceptual designs of two salt cavern based LNG terminals, one with caverns located in Calcasieu Parish Louisiana, and the second in Vermilion block 179 about 50 miles offshore Louisiana. These conceptual designs were compared to conventional tank based LNG terminals and demonstrate superior security, economy and capacity. The potential for the development of LNG receiving terminals

  6. ASTRID© - Advanced Solar Tubular ReceIver Design: A powerful tool for receiver design and optimization

    Science.gov (United States)

    Frantz, Cathy; Fritsch, Andreas; Uhlig, Ralf

    2017-06-01

    In solar tower power plants the receiver is one of the critical components. It converts the solar radiation into heat and must withstand high heat flux densities and high daily or even hourly gradients (due to passage of clouds). For this reason, the challenge during receiver design is to find a reasonable compromise between receiver efficiency, reliability, lifetime and cost. There is a strong interaction between the heliostat field, the receiver and the heat transfer fluid. Therefore, a proper receiver design needs to consider these components within the receiver optimization. There are several design and optimization tools for receivers, but most of them focus only on the receiver, ignoring the heliostat field and other parts of the plant. During the last years DLR developed the ASTRIDcode for tubular receiver concept simulation. The code comprises both a high and a low-detail model. The low-detail model utilizes a number of simplifications which allow the user to screen a high number of receiver concepts for optimization purposes. The high-detail model uses a FE model and is able to compute local absorber and salt temperatures with high accuracy. One key strength of the ASTRIDcode is its interface to a ray tracing software which simulates a realistic heat flux distributions on the receiver surface. The results generated by the ASTRIDcode have been validated by CFD simulations and measurement data.

  7. 'Chaos' in superregenerative receivers

    Energy Technology Data Exchange (ETDEWEB)

    Commercon, Jean-Claude [INSA, Department d' Informatiques, Ba-hat t B. Pascal, 20 Avenue Albert Einsten, 69621 Villeurbaune (France)]. E-mail: jean-claude.commercon@insa-lyon.fr; Badard, Robert [INSA, Department d' Informatiques, Bat B. Pascal, 20 Avenue Albert Einsten, 69621 Villeurbaune (France)]. E-mail: robert.badard@insa-lyon.fr

    2005-02-01

    The superregenerative principle has been known since the early 1920s. The circuit is extremely simple and extremely sensitive. Today, superheterodyne receivers generally supplant superregenerative receivers in most applications because there are several undesirable characteristics: poor selectivity, reradiation, etc. Superregenerative receivers undergo a revival in recent papers for wireless systems, where low cost and very low power consumption are relevant: house/building meters (such as water, energy, gas counter), personal computer environment (keyboard, mouse), etc. Another drawback is the noise level which is higher than that of a well-designed superheterodyne receiver; without an antenna input signal, the output of the receiver hears in an earphone as a waterfall noise; this sound principally is the inherent input noise amplified and detected by the circuit; however, when the input noise is negligible with respect of an antenna input signal, we are faced to an other source of 'noise' self-generated by the superregenerative working. The main objective of this paper concerns this self-generated noise coming from an exponential growing followed by a re-injection process for which the final state is a function of the phase of the input signal.

  8. The ‘vivid sociolinguistic profiling’ of Received Pronunciation

    DEFF Research Database (Denmark)

    Fabricius, Anne

    2006-01-01

    The present paper contributes to an ongoing debate on the sociolinguistic situation of modern Received Pronunciation (hereafter RP) , the social elite accent of England (Milroy 2001; Mugglestone 2003). It reports on an attitudinal study which elicited openended as well as scaled responses...... to samples of RP and nonRP spontaneous dialectindiscourse. This research agenda is a natural extension of studies of synchronic variation and generational change in RP (see e.g. Fabricius 2000, 2002a, 2002b)....

  9. The Communication Between Designer and Design Receiver

    DEFF Research Database (Denmark)

    Dai, Zheng; Dai, Yan

    2009-01-01

    When people think about a product,the first impression always mainly influences the result.Product is the medium of communication between designer and designer receiver.Because both of them have varied different experience and background,the information would be biased during the transferring...... process.The common symbols which can be recognized by both of designer and receiver are the key tools for communication.In some case,the same symbol in one product would be leads to different receiver impression.Generally,impression includes 3 aspects:aesthetics,function, and emotion.Designer needs...... to create an attractive and accurate impression in product from these 3 aspects.For facing the dilemma of communication,some experimental approaches can help designer deal with unique and diversity situations.Solving the detail problem in each step could keep the original meaning of designer....

  10. Precision Continuum Receivers for Astrophysical Applications

    Science.gov (United States)

    Wollack, Edward J.

    2011-01-01

    Cryogenically cooled HEMT (High Electron Mobility Transistor) amplifiers find widespread use in radioastronomy receivers. In recent years, these devices have also been commonly employed in broadband receivers for precision measurements of the Cosmic Microwave Background (CMB) radiation. In this setting, the combination of ultra-low-noise and low-spectral-resolution observations reinforce the importance achieving suitable control over the device environment to achieve fundamentally limited receiver performance. The influence of the intrinsic amplifier stability at low frequencies on data quality (e.g., achievable noise and residual temporal correlations), observational and calibration strategies, as well as architectural mitigation approaches in this setting will be discussed. The implications of device level 1/f fluctuations reported in the literature on system performance will be reviewed.

  11. Multistandard Receiver Design for Telemedicine Monitoring System

    Directory of Open Access Journals (Sweden)

    Hongmei Wang

    2018-01-01

    Full Text Available In short-distance wireless communications for telemedicine monitoring, different medical data measurement equipment has different wireless transmission modes. A multistandard receiver is designed that can adapt to different medical data measuring equipment. Using a second-order bandpass sampling for the design of antialiasing filters, two aliasing signals can be separated. Simultaneously, constraint conditions for sampling frequency are not as critical. The design is useful for a multistandard receiver in a telemedicine monitoring system and has the advantages such as saving spectrum resources and facilitating spectrum planning.

  12. Building and Testing a Portable VLF Receiver

    Science.gov (United States)

    McLaughlin, Robert; Krause, L.

    2014-01-01

    Unwanted emissions or signal noise is a major problem for VLF radio receivers. These can occur from man made sources such as power line hum, which can be prevalent for many harmonics after the fundamental 50 or 60 Hz AC source or from VLF radio transmissions such as LORAN, used for navigation and communications. Natural emissions can also be detrimental to the quality of recordings as some of the more interesting natural emissions such as whistlers or auroral chorus may be drowned out by the more common sferic emissions. VLF receivers must selectively filter out unwanted emissions and amplify the filtered signal to a record-able level without degrading the quality.

  13. Billing and accounts receivable: fundamentals for improvement.

    Science.gov (United States)

    Bizon, M M

    1993-07-01

    If a healthcare facility's accounts receivable operation is experiencing problems, the patient accounts manager should survey all areas of his or her responsibility to determine the best method of resolving the difficulties. One effective technique to reduce billing problems is to take a proactive--not reactive--approach. If mistakes can be corrected before they get out of control, and if the patient accounts manager can ensure that claims will not be denied, a healthcare facility's accounts receivable should remain in good condition.

  14. Improved timing recovery in wireless mobile receivers

    CSIR Research Space (South Africa)

    Olwal, TO

    2007-06-01

    Full Text Available are transmitted to the receiver. In the proposed method, the receiver exploits the soft decisions computed at each turbo decoding iteration to provide reliable estimates of a soft timing signal, which in turn, improves the decoding time. The derived method... as ( ) ( )( )1 2 1 2, ,..., , ,...,Q Qk k k k k k k k ka a x x x P a x x xη∗ ∗∈Β= ∑ (29) where ( )1 2, ,..., Qk k kx x x are the Q coded bits in a multilevel symbol modulation scheme [32]. According to [29], the soft information demapper computes posteriori...

  15. effects of sulphur addition on addition on and mechanical properties

    African Journals Online (AJOL)

    User

    234-8034714355. 8034714355. 1. EFFECTS OF SULPHUR ADDITION ON. ADDITION ON. 2. AND MECHANICAL PROPERTIES O. 3. 4. C. W. Onyia. 5. 1DEPT. OF METALLURGICAL AND MATERIALS. 6. 2, 4DEPT. OF METALLURGICAL ...

  16. Baseload Nitrate Salt Central Receiver Power Plant Design Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Tilley, Drake [Abengoa Solar LLC, Lakewood, CO (United States); Kelly, Bruce [Abengoa Solar LLC, Lakewood, CO (United States); Burkholder, Frank [Abengoa Solar LLC, Lakewood, CO (United States)

    2014-12-12

    manufacturing. The cost and design goals for the project were met with this task, but the most interesting results had to do with defining the failure modes and looking at a “shakedown analysis” of the combined creep-fatigue failure. A separate task also looked at improving the absorber coatings on the receiver tubes that would improve the efficiency of the receiver. Significant progress was made on developing a novel paint with a high absorptivity that was on par with the current Pyromark, but shows additional potential to be optimized further. Although the coating did not meet the emissivity goals, preliminary testing the new paint shows potential to be much more durable, and potential to improve the receiver efficiency through a higher average absorptivity over the lifetime. Additional coatings were also designed and modeled results meet the project goals, but were not tested. Testing for low cycle fatigue of the full length receiver tubes was designed and constructed, but is still currently undergoing testing. A novel small heliostat was developed through an extensive brainstorming and down select. The concept was then detailed further with inputs from component testing and eventually a full prototype was built and tested. This task met or exceeded the accuracy and structure goals and also beat the cost goal. This provides a significant solar field costs savings for Abengoa that will be developed further to be used in future commercial plants. Ultimately the $0.09/kWhe (real 2009 $) and 6,400 hours goals of the project were met.

  17. Development of wide band digital receiver for atmospheric radars using COTS board based SDR

    Science.gov (United States)

    Yasodha, Polisetti; Jayaraman, Achuthan; Thriveni, A.

    2016-07-01

    Digital receiver extracts the received echo signal information, and is a potential subsystem for atmospheric radar, also referred to as wind profiling radar (WPR), which provides the vertical profiles of 3-dimensional wind vector in the atmosphere. This paper presents the development of digital receiver using COTS board based Software Defined Radio technique, which can be used for atmospheric radars. The developmental work is being carried out at National Atmospheric Research Laboratory (NARL), Gadanki. The digital receiver consists of a commercially available software defined radio (SDR) board called as universal software radio peripheral B210 (USRP B210) and a personal computer. USRP B210 operates over a wider frequency range from 70 MHz to 6 GHz and hence can be used for variety of radars like Doppler weather radars operating in S/C bands, in addition to wind profiling radars operating in VHF, UHF and L bands. Due to the flexibility and re-configurability of SDR, where the component functionalities are implemented in software, it is easy to modify the software to receive the echoes and process them as per the requirement suitable for the type of the radar intended. Hence, USRP B210 board along with the computer forms a versatile digital receiver from 70 MHz to 6 GHz. It has an inbuilt direct conversion transceiver with two transmit and two receive channels, which can be operated in fully coherent 2x2 MIMO fashion and thus it can be used as a two channel receiver. Multiple USRP B210 boards can be synchronized using the pulse per second (PPS) input provided on the board, to configure multi-channel digital receiver system. RF gain of the transceiver can be varied from 0 to 70 dB. The board can be controlled from the computer via USB 3.0 interface through USRP hardware driver (UHD), which is an open source cross platform driver. The USRP B210 board is connected to the personal computer through USB 3.0. Reference (10 MHz) clock signal from the radar master oscillator

  18. Sustainability Characterization for Additive Manufacturing.

    Science.gov (United States)

    Mani, Mahesh; Lyons, Kevin W; Gupta, S K

    2014-01-01

    Additive manufacturing (AM) has the potential to create geometrically complex parts that require a high degree of customization, using less material and producing less waste. Recent studies have shown that AM can be an economically viable option for use by the industry, yet there are some inherent challenges associated with AM for wider acceptance. The lack of standards in AM impedes its use for parts production since industries primarily depend on established standards in processes and material selection to ensure the consistency and quality. Inability to compare AM performance against traditional manufacturing methods can be a barrier for implementing AM processes. AM process sustainability has become a driver due to growing environmental concerns for manufacturing. This has reinforced the importance to understand and characterize AM processes for sustainability. Process characterization for sustainability will help close the gaps for comparing AM performance to traditional manufacturing methods. Based on a literature review, this paper first examines the potential environmental impacts of AM. A methodology for sustainability characterization of AM is then proposed to serve as a resource for the community to benchmark AM processes for sustainability. Next, research perspectives are discussed along with relevant standardization efforts.

  19. Richard W. Ziolkowski Receives Honorary Doctorate

    DEFF Research Database (Denmark)

    Breinbjerg, Olav

    2012-01-01

    At the annual Commemoration of the Technical University of Denmark (DTU) on April 27, 2012, Prof. Richard W. Ziolkowski, University of Arizona (UoA), received DTU's highest academic degree, the Honorary Doctor degree: Doctor Technices Honoris Causa (Figure 1). Prof. Ziolkowski has been a close...

  20. Howard Feiertag receives hospitality industry award

    OpenAIRE

    Ho, Sookhan

    2004-01-01

    Howard Feiertag, of Blacksburg, an instructor in hospitality and tourism management at Virginia Tech's Pamplin College of Business, received the inaugural Excellence in Sales and Marketing Strategy Award at the Hospitality Sales and Marketing Association/New York University Strategy Conference in New York recently.

  1. 7 CFR 966.124 - Approved receiver.

    Science.gov (United States)

    2010-01-01

    ... limited to, the following information: (1) Name, address, contact person, telephone number, and e-mail... 7 Agriculture 8 2010-01-01 2010-01-01 false Approved receiver. 966.124 Section 966.124 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements...

  2. A 24GHz Radar Receiver in CMOS

    NARCIS (Netherlands)

    Kwok, K.C.

    2015-01-01

    This thesis investigates the system design and circuit implementation of a 24GHz-band short-range radar receiver in CMOS technology. The propagation and penetration properties of EM wave offer the possibility of non-contact based remote sensing and through-the-wall imaging of distance stationary or

  3. 8. Prevalence of Epistaxis among Patients Receiving ...

    African Journals Online (AJOL)

    user

    The aim of this study was thus to determine the prevalence, aetiology and treatment modalities of epistaxis among patients receiving otorhinolaryngology services at MNH and MOI. Materials and Methods: A cross-sectional, hospital based study was done to 427 patients at Muhimbili. National Hospital (MNH) and Muhimbili.

  4. Reasons Parents Exempt Children from Receiving Immunizations

    Science.gov (United States)

    Luthy, Karlen E.; Beckstrand, Renea L.; Callister, Lynn C.; Cahoon, Spencer

    2012-01-01

    School nurses are on the front lines of educational efforts to promote childhood vaccinations. However, some parents still choose to exempt their children from receiving vaccinations for personal reasons. Studying the beliefs of parents who exempt vaccinations allows health care workers, including school nurses, to better understand parental…

  5. Social effects of migration in receiving countries.

    Science.gov (United States)

    Ohndorf, W

    1989-06-01

    This paper examines the impact of post-1945 migration into Western, Middle, and Northern Europe from Southern Europe, Turkey, and Northern Africa, and migration to the traditional immigration countries by Asian and Latin American immigrants, on the social structures of receiving countries. Between 1955 and 1974, 1) traditional migration to the US and Australia became less important for European countries while traditional receiving countries accepted many immigrants from developing countries; and 2) rapid economic revival in Western and Northern Europe caused a considerable labor shortage which was filled by migrant workers especially from Southern Europe, Turkey, and Northern Africa, who stayed only until they reached their economic goals. Since 1974, job vacancies have declined and unemployment has soared. This employment crisis caused some migrants 1) to return to their countries of origin, 2) to bring the rest of their families to the receiving country, or 3) to lengthen their stay considerably. The number of refugees has also significantly increased since the mid-970s, as has the number of illegal migrants. After the mid-1970s, Europe began to experience integration problems. The different aspects of the impact of migration on social structures include 1) improvement of the housing situation for foreigners, 2) teaching migrants the language of the receiving country, 3) solving the unemployment problem of unskilled migrants, 4) improvement of educational and vocational qualifications of 2nd generation migrants, 5) development of programs to help unemployed wives of migrants to learn the language and meet indigenous women, 6) encouraging migrants to maintain their cultural identity and assisting them with reintegration if they return to their original country, 7) coping with the problems of refugees, and 8) solving the problems of illegal migration. Almost all receiving countries now severely restrict further immigration. [Those policies should result in

  6. Remark on receiving encouraging prize; Shoreisho jusho shokan

    Energy Technology Data Exchange (ETDEWEB)

    Mizutani, Tomichika [Meji University, Tokyo (Japan)

    1999-07-31

    The 1998 fiscal year Japan Solar Energy Soc. encouraging prize is received this time, and it is really sure of thank you and this winning prize for future research activity with large encouragement, while research activity in the university becomes in the good commemoration. This study also put environmental problem in visual field oil crisis energy resource worldwide new, and it was noticed in the wave energy which was one of the natural energy, it was started. That the wave energy was noticed, when the research of various natural energy was advanced, Over 10 years, it is the idea which was produced by the process in which the mechanics laboratory studies the vibration problem, and it is regarded as connecting with present winning prize as a summing-up of research result kept since the front. In the keyword of 'new{exclamation_point}' it began to leave Mr.Taichi Matsuoka and cooperation of the science graduate student as a partner of the graduation thesis the research the present it was a start from the nothing as a thing of this type. It is negative to advance this study in which the failure was always given here, when the new work began, of Mr.Matsuoka of the passion for the research. Away from the research of the wave power generation, solar light and wind power generation are noticed a little, and I aim at the hybridization of the wave power generation, and the research is advanced. Therefore, the vibration-proof stage for installing sun and wind energy conversion system on the wave-power device at present has been designed. At the end, the gratitude is shown to the everybody who received the enthusiastic guidance for this study. (translated by NEDO)

  7. Ultrawide Bandwidth Receiver Based on a Multivariate Generalized Gaussian Distribution

    KAUST Repository

    Ahmed, Qasim Zeeshan

    2015-04-01

    Multivariate generalized Gaussian density (MGGD) is used to approximate the multiple access interference (MAI) and additive white Gaussian noise in pulse-based ultrawide bandwidth (UWB) system. The MGGD probability density function (pdf) is shown to be a better approximation of a UWB system as compared to multivariate Gaussian, multivariate Laplacian and multivariate Gaussian-Laplacian mixture (GLM). The similarity between the simulated and the approximated pdf is measured with the help of modified Kullback-Leibler distance (KLD). It is also shown that MGGD has the smallest KLD as compared to Gaussian, Laplacian and GLM densities. A receiver based on the principles of minimum bit error rate is designed for the MGGD pdf. As the requirement is stringent, the adaptive implementation of the receiver is also carried out in this paper. Training sequence of the desired user is the only requirement when implementing the detector adaptively. © 2002-2012 IEEE.

  8. On the Convergence of Iterative Receiver Algorithms Utilizing Hard Decisions

    Directory of Open Access Journals (Sweden)

    Jürgen F. Rößler

    2009-01-01

    Full Text Available The convergence of receivers performing iterative hard decision interference cancellation (IHDIC is analyzed in a general framework for ASK, PSK, and QAM constellations. We first give an overview of IHDIC algorithms known from the literature applied to linear modulation and DS-CDMA-based transmission systems and show the relation to Hopfield neural network theory. It is proven analytically that IHDIC with serial update scheme always converges to a stable state in the estimated values in course of iterations and that IHDIC with parallel update scheme converges to cycles of length 2. Additionally, we visualize the convergence behavior with the aid of convergence charts. Doing so, we give insight into possible errors occurring in IHDIC which turn out to be caused by locked error situations. The derived results can directly be applied to those iterative soft decision interference cancellation (ISDIC receivers whose soft decision functions approach hard decision functions in course of the iterations.

  9. Synchronous OEIC Integrating Receiver for Optically Reconfigurable Gate Arrays

    Directory of Open Access Journals (Sweden)

    Carlos Sánchez-Azqueta

    2016-05-01

    Full Text Available A monolithically integrated optoelectronic receiver with a low-capacitance on-chip pin photodiode is presented. The receiver is fabricated in a 0.35 μm opto-CMOS process fed at 3.3 V and due to the highly effective integrated pin photodiode it operates at μW. A regenerative latch acting as a sense amplifier leads in addition to a low electrical power consumption. At 400 Mbit/s, sensitivities of −26.0 dBm and −25.5 dBm are achieved, respectively, for λ = 635 nm and λ = 675 nm (BER = 10−9 with an energy efficiency of 2 pJ/bit.

  10. ADDITIVES USED TO OBTAIN FOOD

    Directory of Open Access Journals (Sweden)

    Dorina Ardelean

    2012-01-01

    Full Text Available Use of food additives in food is determined by the growth of contemporary food needs of the world population. Additives used in food, both natural and artificial ones, contribute to: improving the organoleptic characteristics and to preserve the food longer, but we must not forget that all these additives should not be found naturally in food products. Some of these additives are not harmful and human pests in small quantities, but others may have harmful effects on health.

  11. Towards full band colorless reception with coherent balanced receivers.

    Science.gov (United States)

    Zhang, Bo; Malouin, Christian; Schmidt, Theodore J

    2012-04-23

    In addition to linear compensation of fiber channel impairments, coherent receivers also provide colorless selection of any desired data channel within multitude of incident wavelengths, without the need of a channel selecting filter. In this paper, we investigate the design requirements for colorless reception using a coherent balanced receiver, considering both the optical front end (OFE) and the transimpedance amplifier (TIA). We develop analytical models to predict the system performance as a function of receiver design parameters and show good agreement against numerical simulations. At low input signal power, an optimum local oscillator (LO) power is shown to exist where the thermal noise is balanced with the residual LO-RIN beat noise. At high input signal power, we show the dominant noise effect is the residual self-beat noise from the out of band (OOB) channels, which scales not only with the number of OOB channels and the common mode rejection ratio (CMRR) of the OFE, but also depends on the link residual chromatic dispersion (CD) and the orientation of the polarization tributaries relative to the receiver. This residual self-beat noise from OOB channels sets the lower bound for the LO power. We also investigate the limitations imposed by overload in the TIA, showing analytically that the DC current scales only with the number of OOB channels, while the differential AC current scales only with the link residual CD, which induces high peak-to-average power ratio (PAPR). Both DC and AC currents at the input to the TIA set the upper bounds for the LO power. Considering both the OFE noise limit and the TIA overload limit, we show that the receiver operating range is notably narrowed for dispersion unmanaged links, as compared to dispersion managed links. © 2012 Optical Society of America

  12. Quantitative research

    DEFF Research Database (Denmark)

    Wigram, Anthony Lewis

    2003-01-01

    possible and desirable. It is not just a type of research done in a laboratory, or by PhD students. Some for of reliable measurement can be applied to many clinical situationsto evaluate the effects of therapy over time, or the difference between clients who receive therapy and those who don't. Evaluating...

  13. Nutritional survey of neoplasm patients receiving radiotherapy

    International Nuclear Information System (INIS)

    Li Xinli; Zhu Shengtao

    2001-01-01

    Objective: In order to know the nutriture of neoplasm patients receiving radiotherapy and give nutritional guidance properly, the authors make the following survey. Methods: A dietary survey of twenty-four-hour retrospective method was used; The patients' activity was recorded and their twenty-four hours caloric consumption was calculated. Results: Of all the patients, the intake of protein is more than recommended, percentage of calorific proportion is about 15%-19% of gross caloric. A larger portion of patients' caloric intake, especially female patients, is lower than caloric consumption. Among all the patients, the intake of vegetables is not enough; The consumption of milk and milky products is lower; it is common and serious that neoplasm patients receiving radiotherapy have vitamine and mineral's scarcity. Conclusions: Nutriture of neoplasm patients is not optimistic, it is imperative to improve their nutriture

  14. Graphene radio frequency receiver integrated circuit.

    Science.gov (United States)

    Han, Shu-Jen; Garcia, Alberto Valdes; Oida, Satoshi; Jenkins, Keith A; Haensch, Wilfried

    2014-01-01

    Graphene has attracted much interest as a future channel material in radio frequency electronics because of its superior electrical properties. Fabrication of a graphene integrated circuit without significantly degrading transistor performance has proven to be challenging, posing one of the major bottlenecks to compete with existing technologies. Here we present a fabrication method fully preserving graphene transistor quality, demonstrated with the implementation of a high-performance three-stage graphene integrated circuit. The circuit operates as a radio frequency receiver performing signal amplification, filtering and downconversion mixing. All circuit components are integrated into 0.6 mm(2) area and fabricated on 200 mm silicon wafers, showing the unprecedented graphene circuit complexity and silicon complementary metal-oxide-semiconductor process compatibility. The demonstrated circuit performance allow us to use graphene integrated circuit to perform practical wireless communication functions, receiving and restoring digital text transmitted on a 4.3-GHz carrier signal.

  15. Division File of Extension Research Materials; Additions During 1968.

    Science.gov (United States)

    Byrn, Darcie, Comp.

    In this annotated bibliography of acquisitions during 1968 appear 265 Extension studies on administrative organization and management; training and staff development; mobilizing participation in Extension work; local leadership; program content and planning procedures; general effectiveness and progress in Extension; teaching methods, techniques,…

  16. RESEARCH OF INTERACTION BETWEEN CAUSTIC MAGNESITE AND A MICROSILICA ADDITIVE

    Directory of Open Access Journals (Sweden)

    Ustinova Yuliya Valerevna

    2012-10-01

    Compressive strength of the dry mix containing 10 % of microsilica has been measured. In the event of hydraulic hardening, the compressive strength of the dry mix is 11.5 MPa, while the compressive strength of the water-saturated mix is equal to 12.0 MPa. In the aftermath of the air-setting procedure, the compressive strength of the dry mix is 10.0 MPa, while the compressive strength of the water-saturated mix is 21.0 MPa. The IR spectra of the specimen exhibit vibrations at 1100-400 cm-1 that correspond to the area of Si-O and Si-O-Me stretching vibrations, a peak at 1121-1119 cm-1 that can be assigned to Si-O-Si bond vibrations, and a peak at 474-472 characteristic of Si-O-Mg stretching vibrations. The areas of 3700-3000 cm-1 and 1650-1600 cm-1 are assigned to stretching and deformational vibrations of OH groups, respectively.

  17. Additive/Subtractive Manufacturing Research and Development in Europe

    Science.gov (United States)

    2004-12-01

    capabilities for modifying meshes. If the dinosaur model is too large to build on a RP machine, it can be split into several pieces, such that each piece...build complex, porous microstructures from biocompatible materials 3. build with living cells, genes, and proteins 4. build multiple, biocompatible...materials and cells/genes/ proteins together and separately on the same platform 5. build at resolutions below 10 microns over structures greater than

  18. Software offers transparent, straightforward assessment of pavement additives : research spotlight.

    Science.gov (United States)

    2015-04-01

    Adding new materials to pavement layers is a proven technique to : improve performance. Many types of additivesfrom engineered : polymers and acids to recycled pavement, crumb rubber, shingles : and glasshave been used to help construct better ...

  19. Additional Research Needs to Support the GENII Biosphere Models

    Energy Technology Data Exchange (ETDEWEB)

    Napier, Bruce A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Snyder, Sandra F. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Arimescu, Carmen [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2013-11-01

    In the course of evaluating the current parameter needs for the GENII Version 2 code (Snyder et al. 2013), areas of possible improvement for both the data and the underlying models have been identified. As the data review was implemented, PNNL staff identified areas where the models can be improved both to accommodate the locally significant pathways identified and also to incorporate newer models. The areas are general data needs for the existing models and improved formulations for the pathway models.

  20. Hypersensitivity reactions in patients receiving hemodialysis.

    Science.gov (United States)

    Butani, Lavjay; Calogiuri, Gianfranco

    2017-06-01

    To describe hypersensitivity reactions in patients receiving maintenance hemodialysis. PubMed search of articles published during the past 30 years with an emphasis on publications in the past decade. Case reports and review articles describing hypersensitivity reactions in the context of hemodialysis. Pharmacologic agents are the most common identifiable cause of hypersensitivity reactions in patients receiving hemodialysis. These include iron, erythropoietin, and heparin, which can cause anaphylactic or pseudoallergic reactions, and topical antibiotics and anesthetics, which lead to delayed-type hypersensitivity reactions. Many hypersensitivity reactions are triggered by complement activation and increased bradykinin resulting from contact system activation, especially in the context of angiotensin-converting enzyme inhibitor use. Several alternative pharmacologic preparations and dialyzer membranes are available, such that once an etiology for the reaction is established, recurrences can be prevented without affecting the quality of care provided to patients. Although hypersensitivity reactions are uncommon in patients receiving hemodialysis, they can be life-threatening. Moreover, considering the large prevalence of the end-stage renal disease population, the implications of such reactions are enormous. Most reactions are pseudoallergic and not mediated by immunoglobulin E. The multiplicity of potential exposures and the complexity of the environment to which patients on dialysis are exposed make it challenging to identify the precise cause of these reactions. Great diligence is needed to investigate hypersensitivity reactions to avoid recurrence in this high-risk population. Copyright © 2017 American College of Allergy, Asthma & Immunology. Published by Elsevier Inc. All rights reserved.

  1. TDRSS S-shuttle unique receiver equipment

    Science.gov (United States)

    Weinberg, A.; Schwartz, J. J.; Spearing, R.

    1985-01-01

    Beginning with STS-9, the Tracking and Date Relay Satellite system (TDRSS) will start providing S- and Ku-band communications and tracking support to the Space Shuttle and its payloads. The most significant element of this support takes place at the TDRSS White Sands Ground Terminal, which processes the Shuttle return link S- and Ku-band signals. While Ku-band hardware available to other TDRSS users is also applied to Ku-Shuttle, stringent S-Shuttle link margins have precluded the application of the standard TDRSS S-band processing equipment to S-Shuttle. It was therfore found necessary to develop a unique S-Shuttle Receiver that embodies state-of-the-art digital technology and processing techniques. This receiver, developed by Motorola, Inc., enhances link margins by 1.5 dB relative to the standard S-band equipment and its bit error rate performance is within a few tenths of a dB of theory. An overview description of the Space Shuttle Receiver Equipment (SSRE) is presented which includes the presentation of block diagrams and salient design features. Selected, measured performance results are also presented.

  2. Multifunction waveform generator for EM receiver testing

    Science.gov (United States)

    Chen, Kai; Jin, Sheng; Deng, Ming

    2018-01-01

    In many electromagnetic (EM) methods - such as magnetotelluric, spectral-induced polarization (SIP), time-domain-induced polarization (TDIP), and controlled-source audio magnetotelluric (CSAMT) methods - it is important to evaluate and test the EM receivers during their development stage. To assess the performance of the developed EM receivers, controlled synthetic data that simulate the observed signals in different modes are required. In CSAMT and SIP mode testing, the waveform generator should use the GPS time as the reference for repeating schedule. Based on our testing, the frequency range, frequency precision, and time synchronization of the currently available function waveform generators on the market are deficient. This paper presents a multifunction waveform generator with three waveforms: (1) a wideband, low-noise electromagnetic field signal to be used for magnetotelluric, audio-magnetotelluric, and long-period magnetotelluric studies; (2) a repeating frequency sweep square waveform for CSAMT and SIP studies; and (3) a positive-zero-negative-zero signal that contains primary and secondary fields for TDIP studies. In this paper, we provide the principles of the above three waveforms along with a hardware design for the generator. Furthermore, testing of the EM receiver was conducted with the waveform generator, and the results of the experiment were compared with those calculated from the simulation and theory in the frequency band of interest.

  3. Submillimeter heterodyne receiver for the CSO telescope

    International Nuclear Information System (INIS)

    Gulkis, S.

    1988-01-01

    This task is to build a cryogenically cooled 620 to 700 GHz astronomical receiver that will be used as a facility instrument at the CalTech Submillimeter Observatory (CSO) on Mauna Kea, Hawaii. The receiver will have applications as a very high resolution spectrometer to investigate spectral lines in planetary and satellite atmospheres, and comets. The receiver will also be used to make continuum measurements of planets, satellites, and asteroids. During FY88, a scale model (200 GHz) SIS mixer radiometer was built and intrgrated into a cryostat designed for use on the CSO telescope. This system will serve as a model to guide the work on the higher frequency mixer. A solid state local oscillator source that covers two bands in the 600 to 700 GHz has been developed under contract JPL and will be delivered before the end of the year. Work has continued on the SIS materials needed for the 620 to 700 GHz mixer. Test hardware has been developed which allow the 1 to 5 curves for SIS material to be easily measured

  4. Towards Self-Clocked Gated OCDMA Receiver

    Science.gov (United States)

    Idris, S.; Osadola, T.; Glesk, I.

    2013-02-01

    A novel incoherent OCDMA receiver with incorporated all-optical clock recovery for self-synchronization of a time gate for the multi access interferences (MAI) suppression and minimizing the effect of data time jitter in incoherent OCDMA system was successfully developed and demonstrated. The solution was implemented and tested in a multiuser environment in an out of the laboratory OCDMA testbed with two-dimensional wavelength-hopping time-spreading coding scheme and OC-48 (2.5 Gbp/s) data rate. The self-clocked all-optical time gate uses SOA-based fibre ring laser optical clock, recovered all-optically from the received OCDMA traffic to control its switching window for cleaning the autocorrelation peak from the surrounding MAI. A wider eye opening was achieved when the all-optically recovered clock from received data was used for synchronization if compared to a static approach with the RF clock being generated by a RF synthesizer. Clean eye diagram was also achieved when recovered clock is used to drive time gating.

  5. Ground receiving station (GRS) of UMS - receiving and processing the electromagnetic wave data from satellite

    International Nuclear Information System (INIS)

    Mohammad Syahmi Nordin; Fauziah Abdul Aziz

    2007-01-01

    The low resolution Automatic Picture Transmission (APT) data from the National Oceanic and Atmospheric Administration (NOAA) polar-orbiting satellites Advanced Very High Resolution Radiometer (AVHRR) is being received and recorded in real-time mode at ground receiving station in School of Science and Technology, Universiti Malaysia Sabah. The system is suitable for the developing and undeveloped countries in south and Southeast Asia and is said to be acceptable for engineering, agricultural, climatological and environmental applications. The system comprises a personal computer attached with a small APT receiver. The data transmission between the ground receiving station and NOAA satellites is using the electromagnetic wave. The relation for receiving and processing the electromagnetic wave in the transmission will be discussed. (Author)

  6. Active polarization imaging system based on optical heterodyne balanced receiver

    Science.gov (United States)

    Xu, Qian; Sun, Jianfeng; Lu, Zhiyong; Zhou, Yu; Luan, Zhu; Hou, Peipei; Liu, liren

    2017-08-01

    Active polarization imaging technology has recently become the hot research field all over the world, which has great potential application value in the military and civil area. By introducing active light source, the Mueller matrix of the target can be calculated according to the incident light and the emitted or reflected light. Compared with conventional direct detection technology, optical heterodyne detection technology have higher receiving sensitivities, which can obtain the whole amplitude, frequency and phase information of the signal light. In this paper, an active polarization imaging system will be designed. Based on optical heterodyne balanced receiver, the system can acquire the horizontal and vertical polarization of reflected optical field simultaneously, which contain the polarization characteristic of the target. Besides, signal to noise ratio and imaging distance can be greatly improved.

  7. 7 CFR 985.153 - Issuance of additional allotment base to new and existing producers.

    Science.gov (United States)

    2010-01-01

    ... made available. (c) Issuance—(1) New producers—(i) Regions: For the purpose of issuing additional... quantities of that class of spearmint oil, shall be eligible to receive a share of the additional allotment... immediately notify each producer who is to receive additional allotment base by issuing that producer an...

  8. 42 CFR 86.20 - Additional conditions.

    Science.gov (United States)

    2010-10-01

    ... 42 Public Health 1 2010-10-01 2010-10-01 false Additional conditions. 86.20 Section 86.20 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES OCCUPATIONAL SAFETY AND HEALTH RESEARCH AND RELATED ACTIVITIES GRANTS FOR EDUCATION PROGRAMS IN OCCUPATIONAL SAFETY AND HEALTH Occupational Safety and Health Training Grants § 86.2...

  9. 77 FR 27736 - Procurement List Additions

    Science.gov (United States)

    2012-05-11

    ... Research Laboratory, Washington, DC. Service Type/Location: Laundry, Refurbishment, and Warehouse Services... Procurement List. SUMMARY: This action adds products and services to the Procurement List that will be... products and services and impact of the additions on the current or most recent contractors, the Committee...

  10. goGPS: open source software for enhancing the accuracy of low-cost receivers by single-frequency relative kinematic positioning

    International Nuclear Information System (INIS)

    Realini, Eugenio; Reguzzoni, Mirko

    2013-01-01

    goGPS is a free and open source satellite positioning software package aiming to provide a collaborative platform for research and teaching purposes. It was first published in 2009 and since then several related projects are on-going. Its objective is the investigation of strategies for enhancing the accuracy of low-cost single-frequency GPS receivers, mainly by relative positioning with respect to a base station and by a tailored extended Kalman filter working directly on code and phase observations. In this paper, the positioning algorithms implemented in goGPS are presented, emphasizing the modularity of the software design; two specific strategies to support the navigation with low-cost receivers are also proposed and discussed, namely an empirical observation weighting function calibrated on the receiver signal-to-noise ratio and the inclusion of height information from a digital terrain model as an additional observation in the Kalman filter. The former is crucial when working with high-sensitivity receivers, while the latter can significantly improve the positioning in the vertical direction. The overall goGPS positioning accuracy is assessed by comparison with a dual-frequency receiver and with the positioning computed by a standard low-cost receiver. The benefits of the calibrated weighting function and the digital terrain model are investigated by an experiment in a dense urban environment. It comes out that the use of goGPS and low-cost receivers leads to results comparable with those obtained by higher level receivers; goGPS has good performances also in a dense urban environment, where its additional features play an important role. (paper)

  11. Non-additive measures theory and applications

    CERN Document Server

    Narukawa, Yasuo; Sugeno, Michio; 9th International Conference on Modeling Decisions for Artificial Intelligence (MDAI 2012)

    2014-01-01

    This book provides a comprehensive and timely report in the area of non-additive measures and integrals. It is based on a panel session on fuzzy measures, fuzzy integrals and aggregation operators held during the 9th International Conference on Modeling Decisions for Artificial Intelligence (MDAI 2012) in Girona, Spain, November 21-23, 2012. The book complements the MDAI 2012 proceedings book, published in Lecture Notes in Computer Science (LNCS) in 2012. The individual chapters, written by key researchers in the field, cover fundamental concepts and important definitions (e.g. the Sugeno integral, definition of entropy for non-additive measures) as well some important applications (e.g. to economics and game theory) of non-additive measures and integrals. The book addresses students, researchers and practitioners working at the forefront of their field.  

  12. Selection of the signal synchronization method in software GPS receivers

    Directory of Open Access Journals (Sweden)

    Vlada S. Sokolović

    2011-04-01

    and Costas's PLL (Phase Lock Loop models of loop tracking of signal synchronization are presented. The analysis is performed by processing the signals from the same satellite and under the same conditions of the initial signal synchronization. The multiple signal processing showed the advantages and disadvantages of the particular methods and the most acceptable solution proved to be the implementation of the DLL tracking loop phase synchronization and the code tracking loop PLL carrier frequency synchronization. The influence of the parameters of the loop itself is shown as well. After the extraction of navigation bits, all bit extracts do not come with an equal phase. This may lead to a wrong decision in rejecting the Decider and bits. Therefore, the paper proposes an additional synchronization of the extracted bits selected by the navigation messages NDA (Non-Data-Aided algorithm in order to perform their correct detection and to position the receiver much faster. Comparison of methods of signal synchronization Based on the analysis of the methods, the simulation results are compared. The results showed that the TDL loop is not resistant to dynamic disturbances of signals, since the synchronization tracking breaks up. In addition, this loop shows susceptibility to the noise from free space. These are sufficient reasons to propose the implementation of the DLL signal tracking loop as an acceptable solution. In addition to the proposal of the tracking loop, tracking loop coefficient values are determined. Conclusion The performed analysis showed that the TDL loop is not resistant to noise and dynamic disorders of the input signal. Therefore, an appropriate solution for the implementation is the DLL loop with six correlates. The DLL tracking loop coefficients are determined as a compromise solution and they are B = 2Hz and γ = 0.7. Also, the coefficients of the PLL tracking loop of frequency synchronization are B = 20Hz and γ = 0.7. The application of the NDA

  13. Automatic Identification System modular receiver for academic purposes

    Science.gov (United States)

    Cabrera, F.; Molina, N.; Tichavska, M.; Araña, V.

    2016-07-01

    The Automatic Identification System (AIS) standard is encompassed within the Global Maritime Distress and Safety System (GMDSS), in force since 1999. The GMDSS is a set of procedures, equipment, and communication protocols designed with the aim of increasing the safety of sea crossings, facilitating navigation, and the rescue of vessels in danger. The use of this system not only is increasingly attractive to security issues but also potentially creates intelligence products throughout the added-value information that this network can transmit from ships on real time (identification, position, course, speed, dimensions, flag, among others). Within the marine electronics market, commercial receivers implement this standard and allow users to access vessel-broadcasted information if in the range of coverage. In addition to satellite services, users may request actionable information from private or public AIS terrestrial networks where real-time feed or historical data can be accessed from its nodes. This paper describes the configuration of an AIS receiver based on a modular design. This modular design facilitates the evaluation of specific modules and also a better understanding of the standard and the possibility of changing hardware modules to improve the performance of the prototype. Thus, the aim of this paper is to describe the system's specifications, its main hardware components, and to present educational didactics on the setup and use of a modular and terrestrial AIS receiver. The latter is for academic purposes and in undergraduate studies such as electrical engineering, telecommunications, and maritime studies.

  14. Dyslipidemia in HIV Infected Children Receiving Highly Active Antiretroviral Therapy.

    Science.gov (United States)

    Mandal, Anirban; Mukherjee, Aparna; Lakshmy, R; Kabra, Sushil K; Lodha, Rakesh

    2016-03-01

    To assess the prevalence of dyslipidemia and lipodystrophy in Indian children receiving non-nucleoside reverse transcriptase inhibitor (NNRTI) based highly active antiretroviral therapy (HAART) and to determine the associated risk factors for the same. The present cross-sectional study was conducted at a Pediatric Clinic of a tertiary care teaching center in India, from May 2011 through December 2012. HIV infected children aged 5-15 y were enrolled if they did not have any severe disease or hospital admission within last 3 mo or receive any medications known to affect the lipid profile. Eighty-one children were on highly active antiretroviral therapy (HAART) for at least 6 mo and 16 were receiving no antiretroviral therapy (ART). Participants' sociodemographic, nutritional, clinical, and laboratory data were recorded in addition to anthropometry and evidence of lipodystrophy. Fasting lipid profile, apolipoprotein A1 and B levels were done for all the children. Among the children on highly active antiretroviral therapy (HAART), 38.3 % had dyslipidemia and 80.2 % had lipodystrophy, while 25 % antiretroviral therapy (ART) naïve HIV infected children had dyslipidemia. No clinically significant risk factors could be identified that increased the risk of dyslipidemia or lipodystrophy in children on highly active antiretroviral therapy (HAART). There is a high prevalence of dyslipidemia and lipodystrophy in Indian children with HIV infection with an imminent need to establish facilities for testing and treatment of these children for metabolic abnormalities.

  15. Superconducting Submm Integrated Receiver for TELIS

    Energy Technology Data Exchange (ETDEWEB)

    Koshelets, V P [Institute of Radio Engineering and Electronics (IREE) (Russian Federation); Ermakov, A B [Institute of Radio Engineering and Electronics (IREE) (Russian Federation); Filippenko, L V [Institute of Radio Engineering and Electronics (IREE) (Russian Federation); Koryukin, O V [Institute of Radio Engineering and Electronics (IREE) (Russian Federation); Khudchenko, A V [Institute of Radio Engineering and Electronics (IREE) (Russian Federation); Sobolev, A S [Institute of Radio Engineering and Electronics (IREE) (Russian Federation); Torgashin, M Yu [Institute of Radio Engineering and Electronics (IREE) (Russian Federation); Yagoubov, P A [SRON National Institute for Space Research (Netherlands); Hoogeveen, R W M [SRON National Institute for Space Research (Netherlands); Vreeling, W J [SRON National Institute for Space Research (Netherlands); Wild, W [SRON National Institute for Space Research (Netherlands); Pylypenko, O M [State Research Center of Superconducting Electronics ' Iceberg' (Ukraine)

    2006-06-01

    In this report we present design and first experimental results for development of the submm superconducting integrated receiver spectrometer for Terahertz Limb Sounder (TELIS). TELIS is a collaborative European project to build up a three-channel heterodyne balloon-based spectrometer for measuring a variety of atmospheric constituents of the stratosphere. The 550 - 650 GHz channel of TELIS is based on a phase-locked Superconducting Integrated Receiver (SIR). SIR is an on-chip combination of a low-noise Superconductor-Insulator-Superconductor (SIS) mixer with quasioptical antenna, a superconducting Flux Flow Oscillator (FFO) acting as Local Oscillator (LO), and SIS harmonic mixer (HM) for FFO phase locking. A number of new solutions were implemented in the new generation of SIR chips. To achieve the wide-band performance of the spectrometer, a side-feed twin-SIS mixer and balanced SIS mixer with 0.8 {mu}m{sup 2} junctions integrated with a double-dipole (or double-slot) antenna is used. An improved design of the FFO for TELIS has been developed and optimized providing a free-running linewidth between 10 and 2 MHz in the frequency range 500 - 700 GHz. It is important to ensure that tuning of a phase-locked (PL) SIR can be performed remotely by telecommand. For this purpose a number of approaches for the PL SIR automatic computer control have been developed. All receiver components (including input optical elements and Martin-Puplett polarization rotating interferometer for single side band operation) will be mounted on a single 4.2 K plate inside a 40 x 180 x 80 mm{sup 3} box. First measurements give an uncorrected double side band (DSB) noise temperature below 250 K measured with the phase-locked FFO; more detailed results are presented at the conference.

  16. Superconducting Submm Integrated Receiver for TELIS

    International Nuclear Information System (INIS)

    Koshelets, V P; Ermakov, A B; Filippenko, L V; Koryukin, O V; Khudchenko, A V; Sobolev, A S; Torgashin, M Yu; Yagoubov, P A; Hoogeveen, R W M; Vreeling, W J; Wild, W; Pylypenko, O M

    2006-01-01

    In this report we present design and first experimental results for development of the submm superconducting integrated receiver spectrometer for Terahertz Limb Sounder (TELIS). TELIS is a collaborative European project to build up a three-channel heterodyne balloon-based spectrometer for measuring a variety of atmospheric constituents of the stratosphere. The 550 - 650 GHz channel of TELIS is based on a phase-locked Superconducting Integrated Receiver (SIR). SIR is an on-chip combination of a low-noise Superconductor-Insulator-Superconductor (SIS) mixer with quasioptical antenna, a superconducting Flux Flow Oscillator (FFO) acting as Local Oscillator (LO), and SIS harmonic mixer (HM) for FFO phase locking. A number of new solutions were implemented in the new generation of SIR chips. To achieve the wide-band performance of the spectrometer, a side-feed twin-SIS mixer and balanced SIS mixer with 0.8 μm 2 junctions integrated with a double-dipole (or double-slot) antenna is used. An improved design of the FFO for TELIS has been developed and optimized providing a free-running linewidth between 10 and 2 MHz in the frequency range 500 - 700 GHz. It is important to ensure that tuning of a phase-locked (PL) SIR can be performed remotely by telecommand. For this purpose a number of approaches for the PL SIR automatic computer control have been developed. All receiver components (including input optical elements and Martin-Puplett polarization rotating interferometer for single side band operation) will be mounted on a single 4.2 K plate inside a 40 x 180 x 80 mm 3 box. First measurements give an uncorrected double side band (DSB) noise temperature below 250 K measured with the phase-locked FFO; more detailed results are presented at the conference

  17. An Efficient Rank Adaptation Algorithm for Cellular MIMO Systems with IRC Receivers

    DEFF Research Database (Denmark)

    Mahmood, Nurul Huda; Berardinelli, Gilberto; Tavares, Fernando Menezes Leitão

    2014-01-01

    Multiple transmit and receive antennas introduce additional degrees of freedom, which can be used to increase the number of spatial channels between a transmitter-receiver pair. Alternately, the additional degrees of freedom can be used to improve the interference resilience property with the help...... algorithm based on an estimate of the mean signal-to-interference-plus-noise ratio (SINR) at an IRC receiver; wherein, we use results from random matrix theory to derive the expression for the mean post-IRC SINR in the presence of interferers with unequal powers. The performance of the proposed algorithm...

  18. Color Addition and Subtraction Apps

    Science.gov (United States)

    Ruiz, Frances; Ruiz, Michael J.

    2015-01-01

    Color addition and subtraction apps in HTML5 have been developed for students as an online hands-on experience so that they can more easily master principles introduced through traditional classroom demonstrations. The evolution of the additive RGB color model is traced through the early IBM color adapters so that students can proceed step by step…

  19. How Safe Are Color Additives?

    Science.gov (United States)

    ... Linkedin Pin it Email Print Subscribe: FDA Consumer Health Information Color additives give the red tint to your fruit punch ... in Foods, Drugs, Cosmetics, and Medical Devices Color Additives: FDA's Regulatory Process and Historical Perspectives ... Health Cosmetics Dietary Supplements Drugs Food Medical Devices Nutrition ...

  20. Density measures and additive property

    OpenAIRE

    Kunisada, Ryoichi

    2015-01-01

    We deal with finitely additive measures defined on all subsets of natural numbers which extend the asymptotic density (density measures). We consider a class of density measures which are constructed from free ultrafilters on natural numbers and study a certain additivity property of such density measures.

  1. Receive, Reorganize, Return: Theatre as Creative Scholarship

    Science.gov (United States)

    Armstrong, Sara; Braunschneider, Theresa

    2016-01-01

    This article focuses on the use of theatre as a mode of creative scholarship, from the research involved in sketch creation to the presentation of that research to academic audiences. We particularly focus on a specific sketch developed by the CRLT Players--one that explores the consequences of subtle discrimination faced by women scientists in…

  2. Non-additive measure and integral

    CERN Document Server

    Denneberg, Dieter

    1994-01-01

    Non-Additive Measure and Integral is the first systematic approach to the subject. Much of the additive theory (convergence theorems, Lebesgue spaces, representation theorems) is generalized, at least for submodular measures which are characterized by having a subadditive integral. The theory is of interest for applications to economic decision theory (decisions under risk and uncertainty), to statistics (including belief functions, fuzzy measures) to cooperative game theory, artificial intelligence, insurance, etc. Non-Additive Measure and Integral collects the results of scattered and often isolated approaches to non-additive measures and their integrals which originate in pure mathematics, potential theory, statistics, game theory, economic decision theory and other fields of application. It unifies, simplifies and generalizes known results and supplements the theory with new results, thus providing a sound basis for applications and further research in this growing field of increasing interest. It also co...

  3. A model for predicting skin dose received by patients from an x-ray ...

    African Journals Online (AJOL)

    Patient dosimetry has raised concern on quality assurance in hospitals. Several organisations and research groups have been advocating ways of minimising radiation dose received by patients in hospitals. In this paper we have shown that it is possible to obtain in a simple way a reasonable estimate of skin dose received ...

  4. Effect of Wind Flow on Convective Heat Losses from Scheffler Solar Concentrator Receivers

    Science.gov (United States)

    Nene, Anita Arvind; Ramachandran, S.; Suyambazhahan, S.

    2018-05-01

    Receiver is an important element of solar concentrator system. In a Scheffler concentrator, solar rays get concentrated at focus of parabolic dish. While radiation losses are more predictable and calculable since strongly related to receiver temperature, convective looses are difficult to estimate in view of additional factors such as wind flow direction, speed, receiver geometry, prior to current work. Experimental investigation was carried out on two geometries of receiver namely cylindrical and conical with 2.7 m2 Scheffler to find optimum condition of tilt to provide best efficiency. Experimental results showed that as compared to cylindrical receiver, conical receiver gave maximum efficiency at 45° tilt angle. However effect of additional factors like wind speed, wind direction on especially convective losses could not be separately seen. The current work was undertaken to investigate further the same two geometries using computation fluid dynamics using FLUENT to compute convective losses considering all variables such at tilt angle of receiver, wind velocity and wind direction. For cylindrical receiver, directional heat transfer coefficient (HTC) is remarkably high to tilt condition meaning this geometry is critical to tilt leading to higher convective heat losses. For conical receiver, directional average HTC is remarkably less to tilt condition leading to lower convective heat loss.

  5. Cardiovascular Disease Among Transgender Adults Receiving Hormone Therapy: A Narrative Review.

    Science.gov (United States)

    Streed, Carl G; Harfouch, Omar; Marvel, Francoise; Blumenthal, Roger S; Martin, Seth S; Mukherjee, Monica

    2017-08-15

    Recent reports estimate that 0.6% of adults in the United States, or approximately 1.4 million persons, identify as transgender. Despite gains in rights and media attention, the reality is that transgender persons experience health disparities, and a dearth of research and evidence-based guidelines remains regarding their specific health needs. The lack of research to characterize cardiovascular disease (CVD) and CVD risk factors in transgender populations receiving cross-sex hormone therapy (CSHT) limits appropriate primary and specialty care. As with hormone therapy in cisgender persons (that is, those whose sex assigned at birth aligns with their gender identity), existing research in transgender populations suggests that CVD risk factors are altered by CSHT. Currently, systemic hormone replacement for cisgender adults requires a nuanced discussion based on baseline risk factors and age of administration of exogenous hormones because of concern regarding an increased risk for myocardial infarction and stroke. For transgender adults, CSHT has been associated with the potential for worsening CVD risk factors (such as blood pressure elevation, insulin resistance, and lipid derangements), although these changes have not been associated with increases in morbidity or mortality in transgender men receiving CSHT. For transgender women, CSHT has known thromboembolic risk, and lower-dose transdermal estrogen formulations are preferred over high-dose oral formulations. In addition, many studies of transgender adults focus predominantly on younger persons, limiting the generalizability of CSHT in older transgender adults. The lack of randomized controlled trials comparing various routes and formulations of CSHT, as well as the paucity of prospective cohort studies, limits knowledge of any associations between CSHT and CVD.

  6. Superconductor Digital-RF Receiver Systems

    Science.gov (United States)

    Mukhanov, Oleg A.; Kirichenko, Dmitri; Vernik, Igor V.; Filippov, Timur V.; Kirichenko, Alexander; Webber, Robert; Dotsenko, Vladimir; Talalaevskii, Andrei; Tang, Jia Cao; Sahu, Anubhav; Shevchenko, Pavel; Miller, Robert; Kaplan, Steven B.; Sarwana, Saad; Gupta, Deepnarayan

    Digital superconductor electronics has been experiencing rapid maturation with the emergence of smaller-scale, lower-cost communications applications which became the major technology drivers. These applications are primarily in the area of wireless communications, radar, and surveillance as well as in imaging and sensor systems. In these areas, the fundamental advantages of superconductivity translate into system benefits through novel Digital-RF architectures with direct digitization of wide band, high frequency radio frequency (RF) signals. At the same time the availability of relatively small 4K cryocoolers has lowered the foremost market barrier for cryogenically-cooled digital electronic systems. Recently, we have achieved a major breakthrough in the development, demonstration, and successful delivery of the cryocooled superconductor digital-RF receivers directly digitizing signals in a broad range from kilohertz to gigahertz. These essentially hybrid-technology systems combine a variety of superconductor and semiconductor technologies packaged with two-stage commercial cryocoolers: cryogenic Nb mixed-signal and digital circuits based on Rapid Single Flux Quantum (RSFQ) technology, room-temperature amplifiers, FPGA processing and control circuitry. The demonstrated cryocooled digital-RF systems are the world's first and fastest directly digitizing receivers operating with live satellite signals in X-band and performing signal acquisition in HF to L-band at ˜30GHz clock frequencies.

  7. Application of Natural Mineral Additives in Construction

    Science.gov (United States)

    Linek, Malgorzata; Nita, Piotr; Wolka, Paweł; Zebrowski, Wojciech

    2017-12-01

    The article concerns the idea of using selected mineral additives in the pavement quality concrete composition. The basis of the research paper was the modification of cement concrete intended for airfield pavements. The application of the additives: metakaolonite and natural zeolite was suggested. Analyses included the assessment of basic physical properties of modifiers. Screening analysis, assessment of micro structure and chemical microanalysis were conducted in case of these materials. The influence of the applied additives on the change of concrete mix parameters was also presented. The impact of zeolite and metakaolinite on the mix density, oxygen content and consistency class was analysed. The influence of modifiers on physical and mechanical changes of the hardened cement concrete was discussed (concrete density, compressive strength and bending strength during fracturing) in diversified research periods. The impact of the applied additives on the changes of internal structure of cement concrete was discussed. Observation of concrete micro structure was conducted using the scanning electron microscope. According to the obtained lab test results, parameters of the applied modifiers and their influence on changes of internal structure of cement concrete are reflected in the increase of mechanical properties of pavement quality concrete. The increase of compressive and bending strength in case of all analysed research periods was proved.

  8. UV Lidar Receiver Analysis for Tropospheric Sensing of Ozone

    Science.gov (United States)

    Pliutau, Denis; DeYoung, Russell J.

    2013-01-01

    A simulation of a ground based Ultra-Violet Differential Absorption Lidar (UV-DIAL) receiver system was performed under realistic daytime conditions to understand how range and lidar performance can be improved for a given UV pulse laser energy. Calculations were also performed for an aerosol channel transmitting at 3 W. The lidar receiver simulation studies were optimized for the purpose of tropospheric ozone measurements. The transmitted lidar UV measurements were from 285 to 295 nm and the aerosol channel was 527-nm. The calculations are based on atmospheric transmission given by the HITRAN database and the Modern Era Retrospective Analysis for Research and Applications (MERRA) meteorological data. The aerosol attenuation is estimated using both the BACKSCAT 4.0 code as well as data collected during the CALIPSO mission. The lidar performance is estimated for both diffuseirradiance free cases corresponding to nighttime operation as well as the daytime diffuse scattered radiation component based on previously reported experimental data. This analysis presets calculations of the UV-DIAL receiver ozone and aerosol measurement range as a function of sky irradiance, filter bandwidth and laser transmitted UV and 527-nm energy

  9. Receiver design for SPAD-based VLC systems under Poisson-Gaussian mixed noise model.

    Science.gov (United States)

    Mao, Tianqi; Wang, Zhaocheng; Wang, Qi

    2017-01-23

    Single-photon avalanche diode (SPAD) is a promising photosensor because of its high sensitivity to optical signals in weak illuminance environment. Recently, it has drawn much attention from researchers in visible light communications (VLC). However, existing literature only deals with the simplified channel model, which only considers the effects of Poisson noise introduced by SPAD, but neglects other noise sources. Specifically, when an analog SPAD detector is applied, there exists Gaussian thermal noise generated by the transimpedance amplifier (TIA) and the digital-to-analog converter (D/A). Therefore, in this paper, we propose an SPAD-based VLC system with pulse-amplitude-modulation (PAM) under Poisson-Gaussian mixed noise model, where Gaussian-distributed thermal noise at the receiver is also investigated. The closed-form conditional likelihood of received signals is derived using the Laplace transform and the saddle-point approximation method, and the corresponding quasi-maximum-likelihood (quasi-ML) detector is proposed. Furthermore, the Poisson-Gaussian-distributed signals are converted to Gaussian variables with the aid of the generalized Anscombe transform (GAT), leading to an equivalent additive white Gaussian noise (AWGN) channel, and a hard-decision-based detector is invoked. Simulation results demonstrate that, the proposed GAT-based detector can reduce the computational complexity with marginal performance loss compared with the proposed quasi-ML detector, and both detectors are capable of accurately demodulating the SPAD-based PAM signals.

  10. Eosinophils increase in animals that received biotherapic

    Directory of Open Access Journals (Sweden)

    Pedro Gilberto Silva Morais

    2012-12-01

    Full Text Available Dairy industry is an important Brazilian economic activity participating of income generation. European breeds cattle aren’t adapted to parasites found in the tropics, like the Rhipicephalus microplus tick. Parasites can acquire resistance to allopathic products, but not to homeopathic products. We evaluate the efficacy of an antiparasiticide biotherapic against the R. microplus tick. The biotherapic was prepared according to the homeopathic pharmacopoeia recommendations from vegetable (Abrotanum and animal products (Rhipicephalus microplus, Amblyomma cajenennense, Haematobia irritans, Musca domestica, Dermatobia hominis, all diluted and vigorous shaken (dynamized in water or alcohol at a ratio of 1:99, in the 12th Centesimal Hahnemann (CH12, with limestone as the carrier. This homeophatic product found in veterinary pharmacies of Ituiutaba’s region, Minas Gerais State, is registered at Ministério da Agricultura, Pecuária e Abastecimento (MAPA. Natural tick infestation was accessed in thirty Girolando (Gir x Holstein cows with 7 to 13 year-old, by monthly counting of tick female bigger than 6 mm, from October/2009 to July/2011. Cows were divided in three groups of 10 similar animals. The treated group (T1 received roughage, concentrate and biotherapic. The placebo group (T2 received roughage, concentrate and limestone and the control group (T3 received only roughage and concentrate. T1 and T2 groups were managed together and remained in the same paddock. T3 group was separed from T1 and T2 by a wire fence. From October 2009 to September 2010 blood cell counts and serum biochemical tests were performed monthly only in T1 and T2, but visual clinical observations were made in all animals. Any group was treated with acaricide when the count’s average reached 50 or more ticks. It was necessary 7 baths with acaricide in T1 and T2, while in T3 group (control group it was necessary 19 acaricide baths to control the cattle tick. We verified

  11. Prevalence of Food Additive Intolerance

    DEFF Research Database (Denmark)

    Madsen, Charlotte Bernhard

    1994-01-01

    The prevalence estimates vary with a factor 100. As the results vary so do the study populations. 6 If the different study populations are accounted for, a common conclusion can be drawn: Food additive intolerance is found in adults with atopic symptoms from the respiratory tract and skin. The prevalence......1 The existing prevalence estimates of food additive intolerance(1-4) are being reviewed. 2 In the EEC report the estimated frequency of food additive intolerance is 0.03% to 0.15% based on data from patient groups. 3 The British population study results in a prevalence estimate of 0.......026%. The challenged population is 81 children and adults with a history of reproducible clinical symptoms after ingestion of food additives. 4 In the Danish population study a prevalence of 1-2% is found in children age 5-16. In this study a total of 606 children mainly with atopic disease have been challenged. 5...

  12. Topology Optimization for Additive Manufacturing

    DEFF Research Database (Denmark)

    Clausen, Anders

    This PhD thesis deals with the combination of topology optimization and additive man-ufacturing (AM, also known as 3D-printing). In addition to my own works, the thesis contains a broader review and assessment of the literature within the field. The thesis first presents a classification...... of the various AM technologies, a review of relevant manufacturing materials, the properties of these materials in the additively manufactured part, as well as manufacturing constraints with a potential for design optimization. Subsequently, specific topology optimization formulations relevant for the most im...... for scalable manufacturing. In relation to interface problems it is shown how a flexible void area may be included into a standard minimum compliance problem by employing an additional design variable field and a sensitivity filter. Furthermore, it is shown how the design of coated structures may be modeled...

  13. (ICSID) ADDITIONAL FACILITY IN INTERNA

    African Journals Online (AJOL)

    Fr. Ikenga

    ... which is adopted by Article 5 of the Additional Facility Rules to guide the ... B, Barrister at Law, e-mail: kcezeibe@yahoo.com; Phone 08033950631 and .... revision and annulment which are internally available under the Washington ...

  14. Food additives: an ethical evaluation.

    Science.gov (United States)

    Mepham, Ben

    2011-01-01

    Food additives are an integral part of the modern food system, but opinion polls showing most Europeans have worries about them imply an urgent need for ethical analysis of their use. The existing literature on food ethics, safety assessment and animal testing. Food additives provide certain advantages in terms of many people's lifestyles. There are disagreements about the appropriate application of the precautionary principle and of the value and ethical validity of animal tests in assessing human safety. Most consumers have a poor understanding of the relative benefits and risks of additives, but concerns over food safety and animal testing remain high. Examining the impacts of food additives on consumer sovereignty, consumer health and on animals used in safety testing should allow a more informed debate about their appropriate uses.

  15. Wide and High Additive Manufacturing

    Energy Technology Data Exchange (ETDEWEB)

    Post, Brian K. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Roschli, Alex C. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2017-03-01

    The goal of this project is to develop and demonstrate the enabling technologies for Wide and High Additive Manufacturing (WHAM). WHAM will open up new areas of U.S. manufacturing for very large tooling in support of the transportation and energy industries, significantly reducing cost and lead time. As with Big Area Additive Manufacturing (BAAM), the initial focus is on the deposition of composite materials.

  16. Additive manufacturing for steels: a review

    Science.gov (United States)

    Zadi-Maad, A.; Rohib, R.; Irawan, A.

    2018-01-01

    Additive manufacturing (AM) of steels involves the layer by layer consolidation of powder or wire feedstock using a heating beam to form near net shape products. For the past decades, the AM technique reaches the maturation of both research grade and commercial production due to significant research work from academic, government and industrial research organization worldwide. AM process has been implemented to replace the conventional process of steel fabrication due to its potentially lower cost and flexibility manufacturing. This paper provides a review of previous research related to the AM methods followed by current challenges issues. The relationship between microstructure, mechanical properties, and process parameters will be discussed. Future trends and recommendation for further works are also provided.

  17. The BINP receives its Golden Hadron award

    CERN Multimedia

    2002-01-01

    On Thursday, 14 September, the LHC Project Leader, Lyn Evans, handed over a Golden Hadron award to Alexander Skrinsky of Russia's Budker Institute of Nuclear Physics (BINP). The prize is awarded in recognition of exceptional performances by suppliers and this year prizes were awarded to two firms, Cockerill-Sambre (Belgium) and Wah-Chang (United States), and to the Budker Institute, which was unable to receive the award at the same time as the two other recipients (see Bulletin No 34/2002, of 19 August 2002). The Russian institute has been rewarded for the particularly high-quality production of 360 dipole magnets and 185 quadrupole magnets for the LHC proton beam transfer lines.

  18. Humboldt SK pilot biodigester receives funding

    Energy Technology Data Exchange (ETDEWEB)

    Anon.

    2005-09-30

    The Canada-Saskatchewan Western Economic Partnership Agreement (WEPA) will provide funding for Canada's first pilot-scale biodigester to be built in Humboldt, Saskatchewan. The $208,138 pilot facility will use household garbage as well as agricultural waste such as manure and livestock operations, abattoirs and food processing to create heat or power and fertilizer. Support for this bio-energy facility, which could also reduce greenhouse gases, will come from the Prairie Agricultural Machinery Institute which has received $186,138 from Canada and Saskatchewan in the form of cost-shared federal-provincial funding. The pilot plant will test different combinations of waste material feedstocks and the characteristics of the resulting gas end products. The pilot facility will also provide design information for full-scale biodigester manufacturers in Canada. It is expected that 25 full-scale biodigesters will be constructed in Canada in the near future.

  19. Receiver based PAPR reduction in OFDMA

    KAUST Repository

    Ali, Anum Z.; Al-Zahrani, Ali Y.; Al-Naffouri, Tareq Y.; Naguib, Ayman F.

    2014-01-01

    High peak-to-average power ratio is one of the major drawbacks of orthogonal frequency division multiplexing (OFDM). Clipping is the simplest peak reduction scheme, however, it requires clipping mitigation at the receiver. Recently compressed sensing has been used for clipping mitigation (by exploiting the sparse nature of clipping signal). However, clipping estimation in multi-user scenario (i.e., OFDMA) is not straightforward as clipping distortions overlap in frequency domain and one cannot distinguish between distortions from different users. In this work, a collaborative clipping removal strategy is proposed based on joint estimation of the clipping distortions from all users. Further, an effective data aided channel estimation strategy for clipped OFDM is also outlined. Simulation results are presented to justify the effectiveness of the proposed schemes. © 2014 IEEE.

  20. Fast digitization and digital receiver technology

    International Nuclear Information System (INIS)

    Kimball, Ralph C.

    2002-01-01

    The potentially lucrative wireless market has led to technological advances in mixed signal devices such as high speed, high resolution A/D and D/A converters. This same market has also driven the development of high performance multi-channel digital receiver and digital transmitter ICs. Similarly, advances in semiconductor processes, coupled with the need for reduced time-to-market, has led to the development of large, enhanced performance, in-circuit programmable logic devices. A review of the key characteristics of these mixed-signal, signal processing and programmable logic devices is presented. The application of these devices and technologies to the instrumentation of Accelerators and Storage Rings is discussed and presented by way of examples. Issues relating to the requirements associated with real-time processing, I/O throughput, reconfigurability, reliability, maintainability and packaging requirements are also addressed

  1. Receiver operator characteristic (ROC) analysis without truth

    International Nuclear Information System (INIS)

    Henkelman, R.M.; Kay, I.; Bronskill, M.J.

    1990-01-01

    Receiver operator characteristic (ROC) analysis, the preferred method of evaluating diagnostic imaging tests, requires an independent assessment of the true state of disease, which can be difficult to obtain and is often of questionable accuracy. A new method of analysis is described which does not require independent truth data and which can be used when several accurate tests are being compared. This method uses correlative information to estimate the underlying model of multivariate normal distributions of disease-positive and disease-negative patients. The method is shown to give results equivalent to conventional ROC analysis in a comparison of computed tomography, radionuclide scintigraphy, and magnetic resonance imaging for liver metastasis. When independent truth is available, the method can be extended to incorporate truth data or to evaluate the consistency of the truth data with the imaging data

  2. MRI in children receiving total parenteral nutrition

    International Nuclear Information System (INIS)

    Quaghebeur, G.; Taylor, W.J.; Kingsley, D.P.E.; Fell, J.M.E.; Reynolds, A.P.; Milla, P.J.

    1996-01-01

    Cranial MRI was obtained in 13 of a group of 57 children receiving long-term parenteral nutrition, who were being investigated for hypermanganasaemia. Increased signal intensity on T1-weighted images has been reported in adult patients on long-term parenteral nutrition and with encephalopathy following chronic manganese exposure in arc welding. It has been postulated that these changes are due to deposition of the paramagnetic trace element manganese. In excess manganese is hepato- and neurotoxic and we present the correlation of whole blood manganese levels with imaging findings. The age range of our patients was 6 months to 10 years, and the duration of therapy 3 months to 10 years. In 7 children we found characteristic increased signal intensity on T1-weighted images, with no abnormality on T2-weighted images. All patients had elevated whole blood manganese levels, suggesting that the basis for this abnormality is indeed deposition of manganese within the tissues. (orig.). With 3 figs

  3. New Packing Structure of Concentration Solar Receiver

    International Nuclear Information System (INIS)

    Tsai, Shang-Yu; Lee, Yueh-Mu; Shih, Zun-Hao; Hong, Hwen-Fen; Shin, Hwa-Yuh; Kuo, Cherng-Tsong

    2010-01-01

    This paper presents a solution to the temperature issue in High Concentration Photovoltaic (HCPV) module device by using different thermal conductive material and packing structure. In general, the open-circuited voltage of a device reduces with the increase of temperature and therefore degrades its efficiency. The thermal conductive material we use in this paper, silicon, has a high thermal conductive coefficient (149 W/m·K) and steady semiconductor properties which are suitable for the application of solar receiver in HCPV module. Solar cell was soldered on a metal-plated Si substrate with a thicker SiO 2 film which acts as an insulating layer. Then it was mounted on an Al-based plate to obtain a better heat dissipating result.

  4. Receiver based PAPR reduction in OFDMA

    KAUST Repository

    Ali, Anum Z.

    2014-05-01

    High peak-to-average power ratio is one of the major drawbacks of orthogonal frequency division multiplexing (OFDM). Clipping is the simplest peak reduction scheme, however, it requires clipping mitigation at the receiver. Recently compressed sensing has been used for clipping mitigation (by exploiting the sparse nature of clipping signal). However, clipping estimation in multi-user scenario (i.e., OFDMA) is not straightforward as clipping distortions overlap in frequency domain and one cannot distinguish between distortions from different users. In this work, a collaborative clipping removal strategy is proposed based on joint estimation of the clipping distortions from all users. Further, an effective data aided channel estimation strategy for clipped OFDM is also outlined. Simulation results are presented to justify the effectiveness of the proposed schemes. © 2014 IEEE.

  5. Additive manufacturing in production: challenges and opportunities

    Science.gov (United States)

    Ahuja, Bhrigu; Karg, Michael; Schmidt, Michael

    2015-03-01

    Additive manufacturing, characterized by its inherent layer by layer fabrication methodology has been coined by many as the latest revolution in the manufacturing industry. Due to its diversification of Materials, processes, system technology and applications, Additive Manufacturing has been synonymized with terminology such as Rapid prototyping, 3D printing, free-form fabrication, Additive Layer Manufacturing, etc. A huge media and public interest in the technology has led to an innovative attempt of exploring the technology for applications beyond the scope of the traditional engineering industry. Nevertheless, it is believed that a critical factor for the long-term success of Additive Manufacturing would be its ability to fulfill the requirements defined by the traditional manufacturing industry. A parallel development in market trends and product requirements has also lead to a wider scope of opportunities for Additive Manufacturing. The presented paper discusses some of the key challenges which are critical to ensure that Additive Manufacturing is truly accepted as a mainstream production technology in the industry. These challenges would highlight on various aspects of production such as product requirements, process management, data management, intellectual property, work flow management, quality assurance, resource planning, etc. In Addition, changing market trends such as product life cycle, mass customization, sustainability, environmental impact and localized production will form the foundation for the follow up discussion on the current limitations and the corresponding research opportunities. A discussion on ongoing research to address these challenges would include topics like process monitoring, design complexity, process standardization, multi-material and hybrid fabrication, new material development, etc.

  6. IAEA receives Iraq's nuclear-related declaration

    International Nuclear Information System (INIS)

    2002-01-01

    Full text: The Director General of the International Atomic Energy Agency, Mohamed ElBaradei, announced that the IAEA received this evening, Sunday, 8 December 2002, at its Headquarters in Vienna, an approximately 2400 page declaration on Iraq's nuclear programme. The declaration consists of about 2100 pages in English and 300 pages in Arabic. The declaration was submitted by the Government of Iraq in response to paragraph 3 of Security Council resolution 1441 (8 November 2002), which requires Iraq to provide to UNMOVIC, the IAEA and to the Security Council, not later than 30 days of the date of that resolution, with 'currently accurate, full, and complete declaration of all aspects of its programmes to develop chemical, biological, and nuclear weapons, ballistic missiles, and other delivery systems... as well as all other chemical, biological, and nuclear programmes, including any which it claims are for purposes not related to weapon production or material'. 'The IAEA will immediately begin to assess this important new document,' said Mr. ElBaradei, 'including the painstaking and systematic cross-checking of the information provided by Iraq against information which the IAEA already has, information that it expects to receive from other Member States, as contemplated in resolution 1441, and results of past and present Agency verification activities.' Complete assessment of the declaration will be time consuming, particularly in light of the need to translate the 300 pages of Arabic text into English. However, the IAEA expects to be able to provide a preliminary analysis of the document to the Security Council within the next ten days, with a fuller assessment to be provided when it reports to the Council at the end of January. (IAEA)

  7. Culture and neuroscience: additive or synergistic?

    Science.gov (United States)

    Dapretto, Mirella; Iacoboni, Marco

    2010-01-01

    The investigation of cultural phenomena using neuroscientific methods—cultural neuroscience (CN)—is receiving increasing attention. Yet it is unclear whether the integration of cultural study and neuroscience is merely additive, providing additional evidence of neural plasticity in the human brain, or truly synergistic, yielding discoveries that neither discipline could have achieved alone. We discuss how the parent fields to CN: cross-cultural psychology, psychological anthropology and cognitive neuroscience inform the investigation of the role of cultural experience in shaping the brain. Drawing on well-established methodologies from cross-cultural psychology and cognitive neuroscience, we outline a set of guidelines for CN, evaluate 17 CN studies in terms of these guidelines, and provide a summary table of our results. We conclude that the combination of culture and neuroscience is both additive and synergistic; while some CN methodologies and findings will represent the direct union of information from parent fields, CN studies employing the methodological rigor required by this logistically challenging new field have the potential to transform existing methodologies and produce unique findings. PMID:20083533

  8. SOME “EXOTIC” INFORMATION SOURCES THAT HAVE BEEN DISCOVERED DURING THE SELECTION OF SERIAL PUBLICATIONS TO SUPPORT RESEARCH IN ENERGY SECURITY, ENERGY CONSERVATION AND ENERGY EFFICIENCY TECHNOLOGIES AND TECHNIQUES: ADVANTAGEOUS ADDITION FOR “PROFESSIONAL READING” OF A POWER ENGINEERING EXPERT

    Directory of Open Access Journals (Sweden)

    V. S. Lazarev

    2018-01-01

    Full Text Available This work is a fragment of ongoing research aimed at creating a comfortable information environment that provides access to the publications of international scientific journals and other periodicals and continuing publications that are necessary to support qualitative performance of research in Priority Directions of the Research and Technical Activities in the Republic of Belarus for 2016–2020. During the citation analysis-based selection of the world scientific serial publications apposite for a qualitative performance of research in energy security, energy conservation and energy efficient technologies and techniques with the use of the data of Journal Citation Reports® (which basic results are available at: https://figshare.com/articles/energy_sec_xlsx/5606053/2 a noticeable amount of non-serial items was also found out in addition to serial publications, as well as some publications that, though being serial, did not look typical to be used in the research activities. Individual consideration of each such “exotic” information source confirmed, however, that their noticeable citedness by the world experts in power engineering looked quite natural. Moreover, it becomes clear that these (apparently wrongly reflected in Journal Citation Reports® information sources are, however, not an “information noise”, but a useful addition to the “professional reading” of power engineering experts. Since these sources are publicly available via the Internet, it was decided just to recommend them for inclusion in the “professional reading” of the CIS power engineering experts, providing the latter with URLs and brief recommendations for the use. All the mentioned data is given in the present article. As for the species structure of the information sources included in our reference list, there are: a database with online access; web-sites of news agencies; web-site of the International Energy Agency; statistical yearbooks and the

  9. Full-wave receiver architecture for the homodyne motion sensor

    Science.gov (United States)

    Haugen, Peter C; Dallum, Gregory E; Welsh, Patrick A; Romero, Carlos E

    2013-11-19

    A homodyne motion sensor or detector based on ultra-wideband radar utilizes the entire received waveform through implementation of a voltage boosting receiver. The receiver includes a receiver input and a receiver output. A first diode is connected to the receiver output. A first charge storage capacitor is connected from between the first diode and the receiver output to ground. A second charge storage capacitor is connected between the receiver input and the first diode. A second diode is connected from between the second charge storage capacitor and the first diode to ground. The dual diode receiver performs voltage boosting of a RF signal received at the receiver input, thereby enhancing receiver sensitivity.

  10. Full-wave receiver architecture for the homodyne motion sensor

    Energy Technology Data Exchange (ETDEWEB)

    Haugen, Peter C.; Dallum, Gregory E.; Welsh, Patrick A.; Romero, Carlos E.

    2015-09-29

    A homodyne motion sensor or detector based on ultra-wideband radar utilizes the entire received waveform through implementation of a voltage boosting receiver. The receiver includes a receiver input and a receiver output. A first diode is connected to the receiver output. A first charge storage capacitor is connected from between the first diode and the receiver output to ground. A second charge storage capacitor is connected between the receiver input and the first diode. A second diode is connected from between the second charge storage capacitor and the first diode to ground. The dual diode receiver performs voltage boosting of a RF signal received at the receiver input, thereby enhancing receiver sensitivity.

  11. effects of sulphur addition on addition on and mechanical properties

    African Journals Online (AJOL)

    User

    on the microstructure and mechanical properties of sand cast been investigated ... owed that the addition of sulphur to Al-12wt%Si alloy. 12wt%Si alloy .... 28 materials. 29. Element. Aluminum. Silicon. Al. Si. Ca. Fe. Cu. Zn. Mn. Mg. Cr. B. 99.71.

  12. Influence of Additives on Reinforced Concrete Durability

    Directory of Open Access Journals (Sweden)

    Neverkovica Darja

    2014-12-01

    Full Text Available The article presents the results of the research on carbonation and chloride induced corrosion mechanisms in reinforced concrete structures, based on three commercially available concrete admixtures: Xypex Admix C-1000, Penetron Admix and Elkem Microsilica. Carbonation takes place due to carbon dioxide diffusion, which in the required amount is present in the air. Chlorides penetrate concrete in case of the use of deicing salt or structure exploitation in marine atmosphere. Based on the implemented research, Elkem Microsilica is the recommended additive for the use in aggressive environmental conditions. Use of Xypex Admix C-1000 and Penetron Admix have only average resistance to the aggressive environmental impact.

  13. Research at LAMPF

    International Nuclear Information System (INIS)

    1992-02-01

    During the past decade, both the science program and the experimental facilities at LAMPF have undergone some significant changes. This report is a concise description of the current research initiatives and of new directions being proposed for the future research program at LAMPF. Traditionally the LAMPF physics program has explored nuclear systems with hadronic probes: pions, protons, and neutrons. In recent years the exploitation of the intense lepton beams -- neutrinos and muons -- at LAMPF has received increasing emphasis. Explorations of issues in electroweak physics and precision tests of quantum electrodynamics have been significant areas of experimentation. A new concept of the program is an increased emphasis on the role of weak interactions in hadronic systems. Here the electroweak force is treated as a well-understood interaction, which can be used to reveal the wave functions and properties of hadronic systems. The manifestations of the electroweak force may be discussed either in the language of quarks interacting through the exchange of W and Z bosons or in terms of nucleons interacting through the exchange of mesons described by both strong and weak coupling constants. Taken together, these topics provide a rich and vital program of fundamental interest in nuclear physics. Atomic physics, astrophysics, materials research, among others, are additional components of the LAMPF-LANSCE experimental activities. Research highlights of this broad program and the research tools available at LAMPF are described briefly in this report

  14. Researcher / Researched: Repositioning Research Paradigms

    Science.gov (United States)

    Meerwald, Agnes May Lin

    2013-01-01

    "Researcher / Researched" calls for a complementary research methodology by proposing autoethnography as both a method and text that crosses the boundaries of conventional and alternative methodologies in higher education. Autoethnography rearticulates the researcher / researched positions by blurring the boundary between them. This…

  15. Phase Noise Tolerant QPSK Receiver Using Phase Sensitive Wavelength Conversion

    DEFF Research Database (Denmark)

    Da Ros, Francesco; Xu, Jing; Lei, Lei

    2013-01-01

    A novel QPSK receiver based on a phase noise reduction pre-stage exploiting PSA in a HNLF and balanced detection is presented. Receiver sensitivity improvement over a conventional balanced receiver is demonstrated.......A novel QPSK receiver based on a phase noise reduction pre-stage exploiting PSA in a HNLF and balanced detection is presented. Receiver sensitivity improvement over a conventional balanced receiver is demonstrated....

  16. Evaluation of certain food additives.

    Science.gov (United States)

    2017-01-01

    This report represents the conclusions of a Joint FAO/WHO Expert Committee convened to evaluate the safety of various food additives, including flavouring agents, with a view to concluding as to safety concerns and to preparing specifications for identity and purity. The first part of the report contains a general discussion of the principles governing the toxicological evaluation of and assessment of dietary exposure to food additives, including flavouring agents. A summary follows of the Committee’s evaluations of technical, toxicological and dietary exposure data for 10 food additives (Allura Red AC; carob bean gum; lutein esters from Tagetes erecta; octenyl succinic acid (OSA)– modified gum arabic; pectin; Quinoline Yellow; rosemary extract; steviol glycosides; tartrazine; and xanthan gum) and five groups of flavouring agents (alicyclic, alicyclic-fused and aromatic-fused ring lactones; aliphatic and aromatic amines and amides; aliphatic secondary alcohols, ketones and related esters; cinnamyl alcohol and related substances; and tetrahydrofuran and furanone derivatives). Specifications for the following food additives were revised: aspartame; cassia gum; citric and fatty acid esters of glycerol (CITREM); modified starches; octanoic acid; starch sodium octenyl succinate; and total colouring matters. Annexed to the report are tables summarizing the Committee’s recommendations for dietary exposures to and toxicological evaluations of all of the food additives, including flavouring agents, considered at this meeting.

  17. Additive manufacturing of tunable lenses

    Science.gov (United States)

    Schlichting, Katja; Novak, Tobias; Heinrich, Andreas

    2017-02-01

    Individual additive manufacturing of optical systems based on 3D Printing offers varied possibilities in design and usage. In addition to the additive manufacturing procedure, the usage of tunable lenses allows further advantages for intelligent optical systems. Our goal is to bring the advantages of additive manufacturing together with the huge potential of tunable lenses. We produced tunable lenses as a bundle without any further processing steps, like polishing. The lenses were designed and directly printed with a 3D Printer as a package. The design contains the membrane as an optical part as well as the mechanical parts of the lens, like the attachments for the sleeves which contain the oil. The dynamic optical lenses were filled with an oil. The focal length of the lenses changes due to a change of the radius of curvature. This change is caused by changing the pressure in the inside of the lens. In addition to that, we designed lenses with special structures to obtain different areas with an individual optical power. We want to discuss the huge potential of this technology for several applications. Further, an appropriate controlling system is needed. Wéll show the possibilities to control and regulate the optical power of the lenses. The lenses could be used for illumination tasks, and in the future, for individual measurement tasks. The main advantage is the individuality and the possibility to create an individual design which completely fulfills the requirements for any specific application.

  18. The addition of disilanes to cumulenes

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Yiyuan [Iowa State Univ., Ames, IA (United States)

    1997-10-08

    The syntheses of silicon-containing compounds and the studies of their rearrangements have been active research areas in the Barton research group. Previously, the addition of disilanes to acetylenes was studied in the group and an intramolecular 2S + 2A mechanism has been proposed. In this thesis, the work is focused on the addition of disilanes to cumulenes. The syntheses of the precursors are discussed and the possible mechanisms for their thermal, photochemical and catalytic rearrangements are proposed. Conjugated organic polymers have been studied in the group since 1985 because of their potential for exhibiting high electroconductivity, photoconductivity, strong non-linear optical response and intense fluorescence. In the second section of this dissertation, the synthesis and property studies of poly(phenylene vinylene) analogues are discussed.

  19. Do Women With Breast Cancer Who Choose Adjunctive Integrative Oncology Care Receive Different Standard Oncologic Treatment?

    Science.gov (United States)

    Standish, Leanna J; Dowd, Fred; Sweet, Erin; Dale, Linda; Andersen, M Robyn

    2018-04-01

    To determine if women with breast cancer who choose adjunctive naturopathic oncology (NO) specialty care receive different standard oncologic treatment when compared with breast cancer patients who receive only standard care. Women with breast cancer stages 0 to 4, aged 18+ who spoke English and sought care from outpatient naturopathic doctor clinics were enrolled in an observational study of clinical and quality of life outcomes. Women who sought NO care 2 or more times within the first 2 years postdiagnosis were identified as NO cases. A matched comparison group of breast cancer patients were identified using the Western Washington Cancer Surveillance System(CSS). A longitudinal cohort design. In addition to self-report data, the CSS provided data on demographics, stage at the time of diagnosis, and initial treatment. Oncology medical records were abstracted in order to provide additional information on standard oncologic treatment for all participants. Cohorts were well matched with regard to demographic, histologic, and prognostic indicators at the time of diagnosis. Approximately 70% of women in both cohorts received standard oncologic care that met the National Comprehensive Cancer Network guidelines. There were no statistically significant differences between the cohorts in treatment received. Fewer women in the NO cohort with estrogen receptor-positive breast cancer appear to have received antiestrogen therapy. Women in both cohorts appear to receive guideline-concordant care. However, women who receive adjunctive NO care may be less likely to receive antiestrogen therapy.

  20. Calcium addition in straw gasification

    DEFF Research Database (Denmark)

    Risnes, H.; Fjellerup, Jan Søren; Henriksen, Ulrik Birk

    2003-01-01

    The present work focuses on the influence of calcium addition in gasification. The inorganic¿organic element interaction as well as the detailed inorganic¿inorganic elements interaction has been studied. The effect of calcium addition as calcium sugar/molasses solutions to straw significantly...... affected the ash chemistry and the ash sintering tendency but much less the char reactivity. Thermo balance test are made and high-temperature X-ray diffraction measurements are performed, the experimental results indicate that with calcium addition major inorganic¿inorganic reactions take place very late...... in the char conversion process. Comprehensive global equilibrium calculations predicted important characteristics of the inorganic ash residue. Equilibrium calculations predict the formation of liquid salt if sufficient amounts of Ca are added and according to experiments as well as calculations calcium binds...

  1. Additive interaction in survival analysis

    DEFF Research Database (Denmark)

    Rod, Naja Hulvej; Lange, Theis; Andersen, Ingelise

    2012-01-01

    It is a widely held belief in public health and clinical decision-making that interventions or preventive strategies should be aimed at patients or population subgroups where most cases could potentially be prevented. To identify such subgroups, deviation from additivity of absolute effects...... an empirical example of interaction between education and smoking on risk of lung cancer. We argue that deviations from additivity of effects are important for public health interventions and clinical decision-making, and such estimations should be encouraged in prospective studies on health. A detailed...... is the relevant measure of interest. Multiplicative survival models, such as the Cox proportional hazards model, are often used to estimate the association between exposure and risk of disease in prospective studies. In Cox models, deviations from additivity have usually been assessed by surrogate measures...

  2. Additional disulfide bonds in insulin

    DEFF Research Database (Denmark)

    Vinther, Tine N; Pettersson, Ingrid; Huus, Kasper

    2015-01-01

    The structure of insulin, a glucose homeostasis-controlling hormone, is highly conserved in all vertebrates and stabilized by three disulfide bonds. Recently, we designed a novel insulin analogue containing a fourth disulfide bond located between positions A10-B4. The N-terminus of insulin's B......-chain is flexible and can adapt multiple conformations. We examined how well disulfide bond predictions algorithms could identify disulfide bonds in this region of insulin. In order to identify stable insulin analogues with additional disulfide bonds, which could be expressed, the Cβ cut-off distance had...... in comparison to analogues with additional disulfide bonds that were more difficult to predict. In contrast, addition of the fourth disulfide bond rendered all analogues resistant to fibrillation under stress conditions and all stable analogues bound to the insulin receptor with picomolar affinities. Thus...

  3. Generalized Additive Models for Nowcasting Cloud Shading

    Czech Academy of Sciences Publication Activity Database

    Brabec, Marek; Paulescu, M.; Badescu, V.

    2014-01-01

    Roč. 101, March (2014), s. 272-282 ISSN 0038-092X R&D Projects: GA MŠk LD12009 Grant - others:European Cooperation in Science and Technology(XE) COST ES1002 Institutional support: RVO:67985807 Keywords : sunshine number * nowcasting * generalized additive model * Markov chain Subject RIV: BB - Applied Statistics, Operational Research Impact factor: 3.469, year: 2014

  4. Conferences on Combinatorial and Additive Number Theory

    CERN Document Server

    2014-01-01

    This proceedings volume is based on papers presented at the Workshops on Combinatorial and Additive Number Theory (CANT), which were held at the Graduate Center of the City University of New York in 2011 and 2012. The goal of the workshops is to survey recent progress in combinatorial number theory and related parts of mathematics. The workshop attracts researchers and students who discuss the state-of-the-art, open problems, and future challenges in number theory.

  5. Additive Manufacturing and Business Models: Current Knowledge and Missing Perspectives

    Directory of Open Access Journals (Sweden)

    Christina Öberg

    2018-06-01

    Full Text Available Additive manufacturing, that is 3D printing technology, may change the way companies operate their businesses. This article adopts a business model perspective to create an understanding of what we know about these changes. It summarizes current knowledge on additive manufacturing within management and business research, and it discusses future research directions in relation to business models for additive manufacturing. Using the scientific database Web of Science, 116 journal articles were identified. The literature review reveals that most research concerns manufacturing optimization. A more holistic view of the changes that additive manufacturing may bring about for firms is needed, as is more research on changed value propositions, and customer/sales-related issues. The article contributes to previous research by systematically summarizing additive manufacturing research in the business and management literature, and by highlighting areas for further investigation related to the business models of individual firms.

  6. The stability of a terahertz receiver based on a superconducting integrated receiver

    International Nuclear Information System (INIS)

    Ozhegov, R V; Gorshkov, K N; Gol'tsman, G N; Kinev, N V; Koshelets, V P

    2011-01-01

    We present the results of stability testing of a terahertz radiometer based on a superconducting receiver with a SIS tunnel junction as the mixer and a flux-flow oscillator as the local oscillator. In the continuum mode, the receiver with a noise temperature of 95 K at 510 GHz measured over the intermediate frequency (IF) passband of 4-8 GHz offered a noise equivalent temperature difference of 10 ± 1 mK at an integration time of 1 s. We offer a method to significantly increase the integration time without the use of complex measurement equipment. The receiver observed a strong signal over a final detection bandwidth of 4 GHz and offered an Allan time of 5 s.

  7. The stability of a terahertz receiver based on a superconducting integrated receiver

    Energy Technology Data Exchange (ETDEWEB)

    Ozhegov, R V; Gorshkov, K N; Gol' tsman, G N [Department of Physics, Moscow State Pedagogical University, Moscow 119992 (Russian Federation); Kinev, N V; Koshelets, V P, E-mail: Ozhegov@rplab.ru [Institute of Radio Engineering and Electronics, 125009 Moscow (Russian Federation)

    2011-03-15

    We present the results of stability testing of a terahertz radiometer based on a superconducting receiver with a SIS tunnel junction as the mixer and a flux-flow oscillator as the local oscillator. In the continuum mode, the receiver with a noise temperature of 95 K at 510 GHz measured over the intermediate frequency (IF) passband of 4-8 GHz offered a noise equivalent temperature difference of 10 {+-} 1 mK at an integration time of 1 s. We offer a method to significantly increase the integration time without the use of complex measurement equipment. The receiver observed a strong signal over a final detection bandwidth of 4 GHz and offered an Allan time of 5 s.

  8. Receiving demulsifying agent from the acid tar

    Energy Technology Data Exchange (ETDEWEB)

    Nikitina, A.A.; Belyaeva, A.S.; Kunakova, R.V. [FGBIHE ' Ufa State Academy of Economics and Services' , Ufa (Russian Federation); Movsumzade, E.M. [FGBIHE ' Ufa State Petroleum Technological Univ.' , Ufa (Russian Federation); Lapidus, A.L. [Russian Academy of Sciences, Moscow (Russian Federation). N.D. Zelinsky Institute of Organic Chemistry

    2012-07-01

    The processing of wastes of petrochemical production makes it possible to reduce the price of produced commodity of petroleum products substantially. Bitumen, fuel oils, tars and other mixture of heavy organic compounds are widely used in road construction, in paint and cable industries, manufacture of roofing materials, are used as boiler and furnace fuel, fuel for marine diesel engines, raw material for the production of modifying additives, fillers, surfaceactive substances, etc. (orig.)

  9. Additive Construction with Mobile Emplacement (ACME)

    Science.gov (United States)

    Vickers, John

    2015-01-01

    The Additive Construction with Mobile Emplacement (ACME) project is developing technology to build structures on planetary surfaces using in-situ resources. The project focuses on the construction of both 2D (landing pads, roads, and structure foundations) and 3D (habitats, garages, radiation shelters, and other structures) infrastructure needs for planetary surface missions. The ACME project seeks to raise the Technology Readiness Level (TRL) of two components needed for planetary surface habitation and exploration: 3D additive construction (e.g., contour crafting), and excavation and handling technologies (to effectively and continuously produce in-situ feedstock). Additionally, the ACME project supports the research and development of new materials for planetary surface construction, with the goal of reducing the amount of material to be launched from Earth.

  10. Aminodisulfides as additives to lubricants

    Energy Technology Data Exchange (ETDEWEB)

    Balin, A.I.; Tarasevich, V.B.; Veretenova, T.N.

    1980-01-01

    A study was carried out and tehcnology developed for producing sulfur-nitrogen containing additives of the type of aminodisulfide by interaction of beta, beta-dichlordialkyl (aryl) disulfides with diethanolamine in a medium of sulfur-diethanolamine. The 2,2'-bis-(diethanol)-dialkyl(aryl) disulfides obtained do not hydrolyze in aqueous soltuions of alkalis, exhibit rather high antiscoring properties and are recommended for tests as active additives of high pressure to SOZH and technological lubricants of the oil and emulsion types.

  11. Additive Manufacturing of Biomaterials, Tissues, and Organs.

    Science.gov (United States)

    Zadpoor, Amir A; Malda, Jos

    2017-01-01

    The introduction of additive manufacturing (AM), often referred to as three-dimensional (3D) printing, has initiated what some believe to be a manufacturing revolution, and has expedited the development of the field of biofabrication. Moreover, recent advances in AM have facilitated further development of patient-specific healthcare solutions. Customization of many healthcare products and services, such as implants, drug delivery devices, medical instruments, prosthetics, and in vitro models, would have been extremely challenging-if not impossible-without AM technologies. The current special issue of the Annals of Biomedical Engineering presents the latest trends in application of AM techniques to healthcare-related areas of research. As a prelude to this special issue, we review here the most important areas of biomedical research and clinical practice that have benefited from recent developments in additive manufacturing techniques. This editorial, therefore, aims to sketch the research landscape within which the other contributions of the special issue can be better understood and positioned. In what follows, we briefly review the application of additive manufacturing techniques in studies addressing biomaterials, (re)generation of tissues and organs, disease models, drug delivery systems, implants, medical instruments, prosthetics, orthotics, and AM objects used for medical visualization and communication.

  12. Verification of ICESat-2/ATLAS Science Receiver Algorithm Onboard Databases

    Science.gov (United States)

    Carabajal, C. C.; Saba, J. L.; Leigh, H. W.; Magruder, L. A.; Urban, T. J.; Mcgarry, J.; Schutz, B. E.

    2013-12-01

    NASA's ICESat-2 mission will fly the Advanced Topographic Laser Altimetry System (ATLAS) instrument on a 3-year mission scheduled to launch in 2016. ATLAS is a single-photon detection system transmitting at 532nm with a laser repetition rate of 10 kHz, and a 6 spot pattern on the Earth's surface. A set of onboard Receiver Algorithms will perform signal processing to reduce the data rate and data volume to acceptable levels. These Algorithms distinguish surface echoes from the background noise, limit the daily data volume, and allow the instrument to telemeter only a small vertical region about the signal. For this purpose, three onboard databases are used: a Surface Reference Map (SRM), a Digital Elevation Model (DEM), and a Digital Relief Maps (DRMs). The DEM provides minimum and maximum heights that limit the signal search region of the onboard algorithms, including a margin for errors in the source databases, and onboard geolocation. Since the surface echoes will be correlated while noise will be randomly distributed, the signal location is found by histogramming the received event times and identifying the histogram bins with statistically significant counts. Once the signal location has been established, the onboard Digital Relief Maps (DRMs) will be used to determine the vertical width of the telemetry band about the signal. University of Texas-Center for Space Research (UT-CSR) is developing the ICESat-2 onboard databases, which are currently being tested using preliminary versions and equivalent representations of elevation ranges and relief more recently developed at Goddard Space Flight Center (GSFC). Global and regional elevation models have been assessed in terms of their accuracy using ICESat geodetic control, and have been used to develop equivalent representations of the onboard databases for testing against the UT-CSR databases, with special emphasis on the ice sheet regions. A series of verification checks have been implemented, including

  13. Apparatus for delivering and receiving radioactive gas

    International Nuclear Information System (INIS)

    Dansky, B.; Epifano, L.; Farella, R.

    1980-01-01

    An apparatus for delivering and receiving gas to and from a patient, such as for lung ventilation studies. In accordance with the invention there is provided a restrictive breathing chamber adapted for coupling to the patient's breathing organs. A system, including a first check valve, is provided for coupling the breathing chamber to an inflatable gas receptacle so as to allow flow only toward the inflatable gas receptacle. Active gas input apparatus, including a second check valve, is also coupled to the breathing chamber, the second check valve allowing flow only toward the breathing chamber means. First and second auxiliary tubes and a gas filter are also provided. A system is provided for coupling the first auxiliary tube from the inflatable receptacle through the gas filter and to an ambient air environment. The second auxiliary tube is coupled from the inflatable receptacle to an ambient air environment. Finally, a gas pump is switchably coupled as between the first and second auxiliary tubes and operative to selectively cause gas flow in the first auxiliary tube toward the ambient environment, and in the second auxiliary tube toward the inflatable receptacle. A gas trap structure is also disclosed

  14. Additive to clay drilling muds

    Energy Technology Data Exchange (ETDEWEB)

    Voytenko, V.S.; Nekrasova, V.B.; Nikitinskiy, E.L.; Ponomarev, V.N.

    1984-01-01

    The purpose of the invention is to improve the lubricating and strengthening properties of clay drilling muds. This goal is achieved because the lubricating and strengthening additive used is waste from the pulp and paper industry at the stage of reprocessing crude sulfate soap into phytosterol.

  15. The selective addition of water

    NARCIS (Netherlands)

    Resch, V.; Hanefeld, U.

    2014-01-01

    Water is omnipresent and essential. Yet at the same time it is a rather unreactive molecule. The direct addition of water to C[double bond, length as m-dash]C double bonds is therefore a challenge not answered convincingly. In this perspective we critically evaluate the selectivity and the

  16. Radiation curable Michael addition compounds

    International Nuclear Information System (INIS)

    Gruber, G.W.; Friedlander, C.B.; McDonald, W.H.; Dowbenko, R.

    1979-01-01

    Radiation polymerizable acrylyloxy-containing reaction products are provided from Michael addition reaction of an amide containing at least two acrylate groups with a primary or secondary amine. The resulting amine adducts of the amide, which contain at least one acrylate group per molecule, possesses high cure rates in air and are useful in compositions for forming coatings. (author)

  17. Additively manufactured porous tantalum implants

    NARCIS (Netherlands)

    Wauthle, Ruben; Van Der Stok, Johan; Yavari, Saber Amin; Van Humbeeck, Jan; Kruth, Jean Pierre; Zadpoor, Amir Abbas; Weinans, Harrie; Mulier, Michiel; Schrooten, Jan

    2015-01-01

    The medical device industry's interest in open porous, metallic biomaterials has increased in response to additive manufacturing techniques enabling the production of complex shapes that cannot be produced with conventional techniques. Tantalum is an important metal for medical devices because of

  18. Evaluation of certain food additives.

    Science.gov (United States)

    2012-01-01

    This report represents the conclusions of a Joint FAO/WHO Expert Committee convened to evaluate the safety of various food additives, including flavouring agents, with a view to concluding as to safety concerns and to preparing specifications for identity and purity. The first part of the report contains a general discussion of the principles governing the toxicological evaluation of and assessment of dietary exposure to food additives, including flavouring agents. A summary follows of the Committee's evaluations of technical, toxicological and dietary exposure data for five food additives (magnesium dihydrogen diphosphate; mineral oil (medium and low viscosity) classes II and III; 3-phytase from Aspergillus niger expressed in Aspergillus niger; serine protease (chymotrypsin) from Nocardiopsis prasina expressed in Bacillus licheniformis; and serine protease (trypsin) from Fusarium oxysporum expressed in Fusarium venenatum) and 16 groups of flavouring agents (aliphatic and aromatic amines and amides; aliphatic and aromatic ethers; aliphatic hydrocarbons, alcohols, aldehydes, ketones, carboxylic acids and related esters, sulfides, disulfides and ethers containing furan substitution; aliphatic linear alpha,beta-unsaturated aldehydes, acids and related alcohols, acetals and esters; amino acids and related substances; epoxides; furfuryl alcohol and related substances; linear and branched-chain aliphatic, unsaturated, unconjugated alcohols, aldehydes, acids and related esters; miscellaneous nitrogen-containing substances; phenol and phenol derivatives; pyrazine derivatives; pyridine, pyrrole and quinoline derivatives; saturated aliphatic acyclic branched-chain primary alcohols, aldehydes and acids; simple aliphatic and aromatic sulfides and thiols; sulfur-containing heterocyclic compounds; and sulfur-substituted furan derivatives). Specifications for the following food additives were revised: ethyl cellulose, mineral oil (medium viscosity), modified starches and titanium

  19. TRAO Multibeam Receiver System and Key Science Programs

    Science.gov (United States)

    Lee, Youngung

    2017-06-01

    Taeduk Radio Astronomy Observatory (TRAO) is now equipped with a main controling computer with VxWorks operating system, a new receiver system, and a new backend system. The new receiver system(TRAO-SEQUOIA) is equipped with high-performing 16-pixel MMIC pre-amplifiers in a 4x4 array, operating within 85~115 GHz frequency range. The system temperature ranges from 150 K (86~110 GHz) to 450 K (115 GHz). The 2nd IF modules with the narrow band and the 8 channels with 4 FFT spectrometers allow to observe 2 frequencies simultaneously within the 85~100 or 100~115 GHz bands for all 16 pixels of the receiver. Radome replacement was completed successfully as of February 2017. In addition, a new servo system will be installed in 2017 summer. We provide OTF (On-The-Fly) as a main observing mode, and position switching mode is available as well. The backend system (FFT spectrometer) provides the 4096x2 channels with fine velocity resolution of about 0.05 km/sec (15 kHz) per channel, and their full spectra bandwidth is 60 MHz. Beam efficiency of the TRAO was measured to be about 46% - 54% (with less than 2% error) between 86 and 115 GHz bands and pointing errors of the 14m telescope were found be 4.4 arcsec in AZ direction and 6 arcsec in EL direction. Generally, we allocate 18 hours of telescope time a day from January to the middle of May, and from October to December. Three Key Science Programs had been selected in 2015 fall and they are supposed to have higher priority for telescope time.

  20. Antidepressant Medication Management among Older Patients Receiving Home Health Care

    Science.gov (United States)

    Bao, Yuhua; Shao, Huibo; Bruce, Martha L.; Press, Matthew J.

    2014-01-01

    Objective Antidepressant management for older patients receiving home health care (HHC) may occur through two pathways: nurse-physician collaboration (without patient visits to the physician) and physician management through office visits. This study examines the relative contribution of the two pathways and how they interplay. Methods Retrospective analysis was conducted using Medicare claims of 7,389 depressed patients 65 or older who received HHC in 2006–7 and who possessed antidepressants at the start of HHC. A change in antidepressant therapy (vs. discontinuation or refill) was the main study outcome and could take the form of a change in dose, switch to a different antidepressant, or augmentation (addition of a new antidepressant). Logistic regressions were estimated to examine how use of home health nursing care, patient visits to physicians, and their interactions predict a change in antidepressant therapy. Results About 30% of patients experienced a change in antidepressants versus 51% who refilled and 18% who discontinued. Receipt of mental health specialty care was associated with a statistically significant, 10–20 percentage-point increase in the probability of antidepressant change; receipt of primary care was associated with a small and statistically significant increase in the probability of antidepressant change among patients with no mental health specialty care and above-average utilization of nursing care. Increased home health nursing care in absence of physician visits was not associated with increased antidepressant change. Conclusions Active antidepressant management resulting in a change in medication occurred on a limited scale among older patients receiving HHC. Addressing knowledge and practice gaps in antidepressant management by primary care providers and home health nurses and improving nurse-physician collaboration will be promising areas for future interventions. PMID:25158915

  1. Design and simulation analysis of non-receiver aware and receiver ...

    African Journals Online (AJOL)

    We present multicast extensions to our recently proposed Location Prediction Based Routing (LPBR) protocol, referred to as NR-MLPBR and R-MLPBR, to simultaneously reduce the number of multicast tree discoveries and number of links per tree and/or the hop count per source-receiver path in mobile ad hoc networks ...

  2. Quality of life assessment in dogs and cats receiving chemotherapy

    DEFF Research Database (Denmark)

    Vøls, Kåre Kryger; Heden, Martin Anker; Kristensen, Annemarie Thuri

    2017-01-01

    This study aimed to review currently reported methods of assessing the effects of chemotherapy on the quality of life (QoL) of canine and feline patients and to explore novel ways to assess QoL in such patients in the light of the experience to date in human pediatric oncology. A qualitative comp...... of potentially relevant parameters in future QoL assessments may benefit owner decision making....... to assess QoL in toddlers. Each of the identified publications including QoL-assessment in dogs and cats receiving chemotherapy applied a different method of QoL-assessment. In addition, the veterinary QoL-assessments were mainly focused on physical clinical parameters, whereas the emotional (6/11), social...... (4/11) and role (4/11) domains were less represented. QoL-assessment of cats and dogs receiving chemotherapy is in its infancy. The most commonly reported method to assess QoL was questionnaire based and mostly included physical and clinical parameters. Standardizing and including a complete range...

  3. Stability Analysis of Receiver ISB for BDS/GPS

    Science.gov (United States)

    Zhang, H.; Hao, J. M.; Tian, Y. G.; Yu, H. L.; Zhou, Y. L.

    2017-07-01

    Stability analysis of receiver ISB (Inter-System Bias) is essential for understanding the feature of ISB as well as the ISB modeling and prediction. In order to analyze the long-term stability of ISB, the data from MGEX (Multi-GNSS Experiment) covering 3 weeks, which are from 2014, 2015 and 2016 respectively, are processed with the precise satellite clock and orbit products provided by Wuhan University and GeoForschungsZentrum (GFZ). Using the ISB calculated by BDS (BeiDou Navigation Satellite System)/GPS (Global Positioning System) combined PPP (Precise Point Positioning), the daily stability and weekly stability of ISB are investigated. The experimental results show that the diurnal variation of ISB is stable, and the average of daily standard deviation is about 0.5 ns. The weekly averages and standard deviations of ISB vary greatly in different years. The weekly averages of ISB are relevant to receiver types. There is a system bias between ISB calculated from the precise products provided by Wuhan University and GFZ. In addition, the system bias of the weekly average ISB of different stations is consistent with each other.

  4. Excessive Additive Effect On Engine Oil Viscosity

    Directory of Open Access Journals (Sweden)

    Vojtěch Kumbár

    2014-01-01

    Full Text Available The main goal of this paper is excessive additive (for oil filling effect on engine oil dynamic viscosity. Research is focused to commercially distribute automotive engine oil with viscosity class 15W–40 designed for vans. There were prepared blends of new and used engine oil without and with oil additive in specific ratio according manufacturer’s recommendations. Dynamic viscosity of blends with additive was compared with pure new and pure used engine oil. The temperature dependence dynamic viscosity of samples was evaluated by using rotary viscometer with standard spindle. Concern was that the oil additive can moves engine oil of several viscosity grades up. It is able to lead to failure in the engine. Mathematical models were used for fitting experimental values of dynamic viscosity. Exponential fit function was selected, which was very accurate because the coefficient of determination R2 achieved high values (0.98–0.99. These models are able to predict viscosity behaviour blends of engine oil and additive.

  5. Valorising side streams in circular animal feed additives

    NARCIS (Netherlands)

    Weide, van der R.Y.; Elissen, H.J.H.; Dijk, van W.; Huurman, Sander; Krimpen, van M.M.

    2016-01-01

    Because of a growing world population there is an increasing need for protein production, in addition to traditional agriculture and fisheries. Several new crops such as microalgae, macro algae, aquatic higher plants, aquatic and terrestrial invertebrates (insects and worms) have received growing

  6. 45 CFR 162.925 - Additional requirements for health plans.

    Science.gov (United States)

    2010-10-01

    ... clearinghouse to receive, process, or transmit a standard transaction may not charge fees or costs in excess of... RELATED REQUIREMENTS ADMINISTRATIVE REQUIREMENTS General Provisions for Transactions § 162.925 Additional... transaction as a standard transaction, the health plan must do so. (2) A health plan may not delay or reject a...

  7. Carbocation lifetimes and entropy of water addition to carbocations ...

    Indian Academy of Sciences (India)

    Unknown

    Carbocation lifetimes and entropy of water addition to carbocations dependent on their stability. V JAGANNADHAM. Department of Chemistry, Osmania University, Hyderabad 500 007, India e-mail: jvandanapu@hotmail.com. MS received 11 January 2002. Abstract. Iminodiazonium ions (α-azidobenzyl carbocations) were ...

  8. R2NA: Received Signal Strength (RSS Ratio-Based Node Authentication for Body Area Network

    Directory of Open Access Journals (Sweden)

    Yang Wu

    2013-12-01

    Full Text Available The body area network (BAN is an emerging branch of wireless sensor networks for personalized applications. The services in BAN usually have a high requirement on security, especially for the medical diagnosis. One of the fundamental directions to ensure security in BAN is how to provide node authentication. Traditional research using cryptography relies on prior secrets shared among nodes, which leads to high resource cost. In addition, most existing non-cryptographic solutions exploit out-of-band (OOB channels, but they need the help of additional hardware support or significant modifications to the system software. To avoid the above problems, this paper presents a proximity-based node authentication scheme, which only uses wireless modules equipped on sensors. With only one sensor and one control unit (CU in BAN, we could detect a unique physical layer characteristic, namely, the difference between the received signal strength (RSS measured on different devices in BAN. Through the above-mentioned particular difference, we can tell whether the sender is close enough to be legitimate. We validate our scheme through both theoretical analysis and experiments, which are conducted on the real Shimmer nodes. The results demonstrate that our proposed scheme has a good security performance.

  9. Attitude Towards Physics and Additional Mathematics Achievement Towards Physics Achievement

    Science.gov (United States)

    Veloo, Arsaythamby; Nor, Rahimah; Khalid, Rozalina

    2015-01-01

    The purpose of this research is to identify the difference in students' attitude towards Physics and Additional Mathematics achievement based on gender and relationship between attitudinal variables towards Physics and Additional Mathematics achievement with achievement in Physics. This research focused on six variables, which is attitude towards…

  10. Design of the Acoustic Signal Receiving Unit of Acoustic Telemetry While Drilling

    Directory of Open Access Journals (Sweden)

    Li Zhigang

    2016-01-01

    Full Text Available Signal receiving unit is one of the core units of the acoustic telemetry system. A new type of acoustic signal receiving unit is designed to solve problems of the existing devices. The unit is a short joint in whole. It not only can receive all the acoustic signals transmitted along the drill string, without losing any signal, but will not bring additional vibration and interference. In addition, the structure of the amplitude transformer is designed, which can amplify the signal amplitude and improve the receiving efficiency. The design of the wireless communication module makes the whole device can be used in normal drilling process when the drill string is rotating. So, it does not interfere with the normal drilling operation.

  11. Qualification test for the flexible receiver

    International Nuclear Information System (INIS)

    Keller, C.M.

    1994-01-01

    This document provides the test plan and procedures to certify and design verify the 42 inch and 4--6 inch Flexible Receiver (FR) is a safety class 3 system. Verification of the design will be handled in two parts. The first part will be to show that it meets design requirements set forth by documents and the second part will perform test(s) to verify its operational aspects. To qualify the design of the FR systems for field use this test will demonstrate environmentally safe removal of a Tank Farm pump mock-up from a Tank Farm riser mock-up. Testing will also demonstrate the performance of supporting equipment. The FR and the Secondary Bagging (SB) equipment shall be tested to verify successful operation of the equipment to the following criteria: The FR can be placed on a riser and connections made to the supporting equipment; The FR bag can accept equipment and be successfully sealed; The SB system encases the seal of the primary FR bag; The flexible bag(s) do not tear and maintain integrity during the entire test; The FR control system operates in the fail safe forced sequence mode; The FR control system will operate in the manual override mode (out of sequence operations); The CCTV Video system monitors and records the removal of the test item; The spray wash system operates without leaks and effectively provides coverage; The item being removed can be reinserted to a depth of 8 feet and the bag reinstalled onto the vertical bag supports; and The system prohibits momentary mechanical fluctuations due to the application of system power, including power interruptions

  12. Crustal Structure beneath Alaska from Receiver Functions

    Science.gov (United States)

    Zhang, Y.; Li, A.

    2017-12-01

    The crustal structure in Alaska has not been well resolved due to the remote nature of much of the state. The USArray Transportable Array (TA), which is operating in Alaska and northwestern Canada, significantly increases the coverage of broadband seismic stations in the region and allows for a more comprehensive study of the crust. We have analyzed P-receiver functions from earthquake data recorded by 76 stations of the TA and AK networks. Both common conversion point (CCP) and H-K methods are used to estimate the mean crustal thickness. The results from the CCP stacking method show that the Denali fault marks a sharp transition from thick crust in the south to thin crust in the north. The thickest crust up to 52 km is located in the St. Elias Range, which has been formed by oblique collision between the Yakutat microplate and North America. A thick crust of 48 km is also observed beneath the eastern Alaska Range. These observations suggest that high topography in Alaska is largely compensated by the thick crust root. The Moho depth ranges from 28 km to 35 km beneath the northern lowlands and increases to 40-45 km under the Books Range. The preliminary crustal thickness from the H-K method generally agrees with that from the CCP stacking with thicker crust beneath high mountain ranges and thinner crust beneath lowlands and basins. However, the offshore part is not well constrained due to the limited coverage of stations. The mean Vp/Vs ratio is around 1.7 in the Yukon-Tanana terrane and central-northern Alaska. The ratio is about 1.9 in central and southern Alaska with higher values at the Alaska Range, Wrangell Mountains, and St. Elias Range. Further data analyses are needed for obtaining more details of the crustal structure in Alaska to decipher the origin and development of different tectonic terranes.

  13. Hypoglycaemia monitoring in a medical receiving ward.

    Science.gov (United States)

    Ellis, Ryan

    2015-01-01

    It has been suggested that current care for diabetes inpatients remains inadequate and that greater attention is required for high quality management. In this project the aspect of hypoglycaemia was studied in a busy medical receiving ward at the Glasgow Royal Infirmary. A large proportion of inpatients have diabetes and episodes of hypoglycaemia experienced by this population can delay discharge and indeed be detrimental to health. Thus it is important from both an organisational and patient perspective to manage this population well. In this project BM machine data was analysed to identify patients who were hypoglycaemic. These patients were then tracked down to study the subsequent management and compared this against recommended guidance. Following this an intervention was made to promote identification, management, documentation, and prevention of hypoglycaemia. This was deliberately a simple intervention involving discussions with staff and provision of basic documented guidance next to every BM machine. In the first phase 17 patients were identified and in a second and third phase 16 patients each time were further identified. Patients in the study were both type 1 and type 2 diabetics. Initial results in phase I were compared to results in phase II and III respectively. This intervention produced significant improvements in management with correct monitoring of low BMs (i.e. upon identification of low BM repeat within 1 hour) improving from 47% to 100% (for Phase II and III). Also, recording of preventative measures of hypoglycaemia improved from 35% to 88% and 94% with an improvement from 24% to 69% and 75% in recording of treatment given if needed. In conclusion, the study successfully demonstrated that simple measures can significantly improve the quality care of inpatient diabetic patients in relation to hypoglycaemia management.

  14. Investigation of the receivability of VLF standard time and frequency ...

    African Journals Online (AJOL)

    This study is on the receivability of some standard time and frequency signals in the VLF range in Zaria, Nigeria. Signal field strengths of various stations were estimated, and a suitable radio receiving system was set up to receive them. Using the assembled receiver, some of the transmissions, including the Omega W/L at ...

  15. 37 CFR 1.412 - The United States Receiving Office.

    Science.gov (United States)

    2010-07-01

    ... Information § 1.412 The United States Receiving Office. (a) The United States Patent and Trademark Office is a Receiving Office only for applicants who are residents or nationals of the United States of America. (b) The... “United States Receiving Office” or by the abbreviation “RO/US.” (c) The major functions of the Receiving...

  16. Protocol for ADDITION-PRO

    DEFF Research Database (Denmark)

    Johansen, Nanna Borup; Hansen, Anne-Louise Smidt; Jensen, Troels M

    2012-01-01

    disease and microvascular diabetic complications. We also require a better understanding of the mechanisms that underlie and drive early changes in cardiometabolic physiology. The ADDITION-PRO study was designed to address these issues among individuals at different levels of diabetes risk recruited from...... Danish primary care. METHODS/DESIGN: ADDITION-PRO is a population-based, longitudinal cohort study of individuals at high risk for diabetes. 16,136 eligible individuals were identified at high risk following participation in a stepwise screening programme in Danish general practice between 2001 and 2006....... All individuals with impaired glucose regulation at screening, those who developed diabetes following screening, and a random sub-sample of those at lower levels of diabetes risk were invited to attend a follow-up health assessment in 2009-2011 (n=4,188), of whom 2,082 (50%) attended. The health...

  17. Additive theory of prime numbers

    CERN Document Server

    Hua, L K

    2009-01-01

    Loo-Keng Hua was a master mathematician, best known for his work using analytic methods in number theory. In particular, Hua is remembered for his contributions to Waring's Problem and his estimates of trigonometric sums. Additive Theory of Prime Numbers is an exposition of the classic methods as well as Hua's own techniques, many of which have now also become classic. An essential starting point is Vinogradov's mean-value theorem for trigonometric sums, which Hua usefully rephrases and improves. Hua states a generalized version of the Waring-Goldbach problem and gives asymptotic formulas for the number of solutions in Waring's Problem when the monomial x^k is replaced by an arbitrary polynomial of degree k. The book is an excellent entry point for readers interested in additive number theory. It will also be of value to those interested in the development of the now classic methods of the subject.

  18. Dolomitic lime containing hydraulic additive

    International Nuclear Information System (INIS)

    Lagzdina, S.; Sedmalis, U.; Bidermanis, L.; Liepins, J.; Grosvalds, I.

    1997-01-01

    To obtain qualitative dolomitic lime the optimum calcination temperature of dolomite containing about 9 % of clayey substances is 900 deg C. The mechanical strength of dolomitic lime containing 30 % of brick waste additive after 6-9 months of hardening is 1.4-1.5 times higher than that of samples without hydraulic additive, for calcium lime - 2.2-2.6 times higher. Generally the mechanical strength of dolomitic lime is higher than that one of calcium lime. It can be explained by the active role of MgO in the hydration and hardening processes of dolomitic lime. Xray diffraction phase analysis was performed by X-ray diffractometer DPON-3M with Cu-K α emission filter

  19. Decontamination formulation with sorbent additive

    Science.gov (United States)

    Tucker; Mark D. , Comstock; Robert H.

    2007-10-16

    A decontamination formulation and method of making that neutralizes the adverse health effects of both chemical and biological compounds, especially chemical warfare (CW) and biological warfare (BW) agents, and toxic industrial chemicals. The formulation provides solubilizing compounds that serve to effectively render the chemical and biological compounds, particularly CW and BW compounds, susceptible to attack, and at least one reactive compound that serves to attack (and detoxify or kill) the compound. The formulation includes at least one solubilizing agent, a reactive compound, a bleaching activator, a sorbent additive, and water. The highly adsorbent, water-soluble sorbent additive (e.g., sorbitol or mannitol) is used to "dry out" one or more liquid ingredients, such as the liquid bleaching activator (e.g., propylene glycol diacetate or glycerol diacetate) and convert the activator into a dry, free-flowing powder that has an extended shelf life, and is more convenient to handle and mix in the field.

  20. The Frontiers of Additive Manufacturing

    Energy Technology Data Exchange (ETDEWEB)

    Grote, Christopher John [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2016-03-03

    Additive manufacturing, more commonly known as 3-D printing, has become a ubiquitous tool in science for its precise control over mechanical design. For additive manufacturing to work, a 3-D structure is split into thin 2D slices, and then different physical properties, such as photo-polymerization or melting, are used to grow the sequential layers. The level of control allows not only for devices to be made with a variety of materials: e.g. plastics, metals, and quantum dots, but to also have finely controlled structures leading to other novel properties. While 3-D printing is widely used by hobbyists for making models, it also has industrial applications in structural engineering, biological tissue scaffolding, customized electric circuitry, fuel cells, security, and more.

  1. Minimum Additive Waste Stabilization (MAWS)

    International Nuclear Information System (INIS)

    1994-02-01

    In the Minimum Additive Waste Stabilization(MAWS) concept, actual waste streams are utilized as additive resources for vitrification, which may contain the basic components (glass formers and fluxes) for making a suitable glass or glassy slag. If too much glass former is present, then the melt viscosity or temperature will be too high for processing; while if there is too much flux, then the durability may suffer. Therefore, there are optimum combinations of these two important classes of constituents depending on the criteria required. The challenge is to combine these resources in such a way that minimizes the use of non-waste additives yet yields a processable and durable final waste form for disposal. The benefit to this approach is that the volume of the final waste form is minimized (waste loading maximized) since little or no additives are used and vitrification itself results in volume reduction through evaporation of water, combustion of organics, and compaction of the solids into a non-porous glass. This implies a significant reduction in disposal costs due to volume reduction alone, and minimizes future risks/costs due to the long term durability and leach resistance of glass. This is accomplished by using integrated systems that are both cost-effective and produce an environmentally sound waste form for disposal. individual component technologies may include: vitrification; thermal destruction; soil washing; gas scrubbing/filtration; and, ion-exchange wastewater treatment. The particular combination of technologies will depend on the waste streams to be treated. At the heart of MAWS is vitrification technology, which incorporates all primary and secondary waste streams into a final, long-term, stabilized glass wasteform. The integrated technology approach, and view of waste streams as resources, is innovative yet practical to cost effectively treat a broad range of DOE mixed and low-level wastes

  2. Trust Trust Me (The Additivity)

    OpenAIRE

    Mano , Ken; Sakurada , Hideki; Tsukada , Yasuyuki

    2017-01-01

    Part 4: Trust Metrics; International audience; We present a mathematical formulation of a trust metric using a quality and quantity pair. Under a certain assumption, we regard trust as an additive value and define the soundness of a trust computation as not to exceed the total sum. Moreover, we point out the importance of not only soundness of each computed trust but also the stability of the trust computation procedure against changes in trust value assignment. In this setting, we define tru...

  3. A manual on using additives

    International Nuclear Information System (INIS)

    Lee, Bong Hoon

    1991-10-01

    This book consists of five chapters, which describe plasticizer ; summary, synthesis of plasticizer, basic notion, analysis and test on plasticizer, stabilizer ; stabilizer for plastic, an antioxidant, phosphorous acid estelle, ultraviolet ray absorbent, performance of stabilizer, influence on another additives, mix case of PVC production and analysis method for stabilizer, ultraviolet ray absorbent ; basic property and ultraviolet ray absorbent maker, anti-static agent ; basics, anti-static agent of a high molecule and analysis of anti-static agent, flame retardant of plastic.

  4. Relative position control design of receiver UAV in flying-boom aerial refueling phase.

    Science.gov (United States)

    An, Shuai; Yuan, Suozhong

    2018-02-01

    This paper proposes the design of the relative position-keeping control of the receiver unmanned aerial vehicle (UAV) with the time-varying mass in the refueling phase utilizing an inner-outer loop structure. Firstly, the model of the receiver in the refueling phase is established. And then tank model is set up to analyze the influence of fuel transfer on the receiver. Subsequently, double power reaching law based sliding mode controller is designed to control receiver translational motion relative to tanker aircraft in the outer loop while active disturbance rejection control technique is applied to the inner loop to stabilize the receiver. In addition, the closed-loop stabilities of the subsystems are established, respectively. Finally, an aerial refueling model under various refueling strategies is utilized. Simulations and comparative analysis demonstrate the effectiveness and robustness of the proposed controllers. Copyright © 2017 ISA. Published by Elsevier Ltd. All rights reserved.

  5. Additive property of separative power

    International Nuclear Information System (INIS)

    Yamamoto, Ichiro; Kanagawa, Akira

    1980-01-01

    A separative power of a separating element, whose heads and tails separation factors are α and β, is expressed by phi sub(b)(α, β) = [α(β - 1)1n α - (α - 1)1n β]/(αβ - 1) for the unit flow of the desired material and phi sub(a)(α, β) (= phi sub(b)(β, α)) for that of undesired material. The additive properties of the functions phi sub(b) and phi sub(a) were demonstrated by calculations of various types of ideal cascades, but the origin of the property is not obvious. The present study has furnished the mathematical basis of the additivity based on the special functional equation. First, for symmetric processes (α = β), the functional equation which describes the function representing the quality of separation f(α, α) concerning the desired material was obtained and solved to give the functional form of f(α, α). The result was extented to the function f(α, β) representing the quality of asymmetric separation (α not equal β). The derived function f(α, β) was demonstrated to be equal to phi sub(b)(α, β), and it was verified that functions phi sub(b)(α, β) and phi sub(a)(α, β) have the additive property in themselves. (author)

  6. Participation for Sustainable Urban Freight Transport Systems : A Case Study of Freight Receivers in the City of Gothenburg

    OpenAIRE

    Lindkvist, Hannes

    2017-01-01

    This thesis is a case study research that look into the difficulty in engaging freight receivers in initiatives related to urban freight transport. The aim of the paper is to investigate how participatory processes could be formed for more successful outcomes and how the freight receivers could become more engaged in the processes. By conducting a qualitative research where primarily interviews with freight receivers and other concerned stakeholder were made, it was possible to distinguish di...

  7. Evaluation of certain food additives.

    Science.gov (United States)

    2009-01-01

    This report represents the conclusions of a Joint FAO/WHO Expert Committee convened to evaluate the safety of various food additives, including flavouring agents, with a view to recommending acceptable daily intakes (ADIs) and to preparing specifications for identity and purity. The first part of the report contains a general discussion of the principles governing the toxicological evaluation and assessment of intake of food additives (in particular, flavouring agents). A summary follows of the Committee's evaluations of technical, toxicological and intake data for certain food additives (asparaginase from Aspergillus niger expressed in A. niger, calcium lignosulfonate (40-65), ethyl lauroyl arginate, paprika extract, phospholipase C expressed in Pichia pastoris, phytosterols, phytostanols and their esters, polydimethylsiloxane, steviol glycosides and sulfites [assessment of dietary exposure]) and 10 groups of related flavouring agents (aliphatic branched-chain saturated and unsaturated alcohols, aldehydes, acids and related esters; aliphatic linear alpha,beta-unsaturated aldehydes, acids and related alcohols, acetals and esters; aliphatic secondary alcohols, ketones and related esters; alkoxy-substituted allylbenzenes present in foods and essential oils and used as flavouring agents; esters of aliphatic acyclic primary alcohols with aliphatic linear saturated carboxylic acids; furan-substituted aliphatic hydrocarbons, alcohols, aldehydes, ketones, carboxylic acids and related esters, sulfides, disulfides and ethers; miscellaneous nitrogen-containing substances; monocyclic and bicyclic secondary alcohols, ketones and related esters; hydroxy- and alkoxy-substituted benzyl derivatives; and substances structurally related to menthol). Specifications for the following food additives were revised: canthaxanthin; carob bean gum and carob bean gum (clarified); chlorophyllin copper complexes, sodium and potassium salts; Fast Green FCF; guar gum and guar gum (clarified

  8. Lindstrom Receives 2013 Ocean Sciences Award: Citation

    Science.gov (United States)

    Gordon, Arnold L.; Lagerloef, Gary S. E.

    2014-09-01

    Eric J. Lindstrom's record over the last 3 decades exemplifies both leadership and service to the ocean science community. Advancement of ocean science not only depends on innovative research but is enabled by support of government agencies. As NASA program scientist for physical oceanography for the last 15 years, Eric combined his proven scientific knowledge and skilled leadership abilities with understanding the inner workings of our government bureaucracy, for the betterment of all. He is a four-time NASA headquarters medalist for his achievements in developing a unified physical oceanography program that is well integrated with those of other federal agencies.

  9. Ostomy patients’ perception of the health care received

    Directory of Open Access Journals (Sweden)

    Candela Bonill-de las Nieves

    2017-12-01

    Full Text Available ABSTRACT Aim: to describe ostomy patient’s perception about health care received, as well as their needs and suggestions for healthcare system improvement. Method: qualitative phenomenological study was conducted, involving individual and semi-structured interviews on the life experiences of 21 adults who had a digestive stoma. Participants were selected following a purposive sampling approach. The analysis was based on the constant comparison of the data, the progressive incorporation of subjects and triangulation among researchers and stoma therapy nurses. The software Atlas.ti was used. Results: perception of health care received is closely related to the information process, as well as training for caring the stoma from peristomal skin to diet. It is worthy to point out the work performed by stoma care nurses ensuring support during all stages of the process. Conclusion: findings contribute to address the main patients’ needs (better prepared nurses, shorter waiting lists, information about sexual relation, inclusion of family members all along the process and recommendations for improving health care to facilitate their adaptation to a new status of having a digestive stoma.

  10. Ionic liquids as lubricant additives: A review

    International Nuclear Information System (INIS)

    Zhou, Yan; Qu, Jun

    2016-01-01

    In pursuit of energy efficiency and durability throughout human history, advances in lubricants have always played important roles. Ionic liquids (ILs) are room-temperature molten salts that possess unique physicochemical properties and have shown great potential in many applications with lubrication as one of the latest. While earlier work (2001–2011) primarily explored the feasibility of using ILs as neat or base lubricants, using ILs as lubricant additives has become the new focal research topic since the breakthrough in ILs’ miscibility in nonpolar hydrocarbon oils in early 2012. This work reviews the recent advances in developing ILs as additives for lubrication with an attempt to correlate among the cationic and anionic structures, oil-solubility, and other relevant physicochemical properties, and lubricating behavior. Effects of the concentration of ILs in lubricants and the compatibility between ILs and other additives in the lubricant formulation on the tribological performance are described followed by a discussion of wear protection mechanism based on tribofilm characterization. As a result, future research directions are suggested at the end.

  11. Additive Manufacturing of Porous Metal

    Energy Technology Data Exchange (ETDEWEB)

    Dehoff, Ryan R. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Kirka, Michael M. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2017-06-01

    Currently, helium is obtained through separation from natural gas. The current industrial process incurs significant costs and requires large energy resources to successfully achieve separation. Through utilizing Additive Manufacturing (AM) technologies it is possible to reduce both of these burdens when refining helium gas. The ability to engineer porosity levels within Inconel 718 discs for controlled separation of helium from natural gas was investigated. Arrays of samples fabricated using the electron beam melting process were analyzed for their relative porosity density. Based upon the measurements, full scale discs were fabricated, and subsequently tested to determine their effectiveness in separating helium from liquefied natural gas.

  12. Iain Stewart Receives 2013 Athelstan Spilhaus Award: Response

    Science.gov (United States)

    Stewart, Iain

    2014-01-01

    It is really wonderful to receive this award and the recognition of AGU for my work. I've been a member of the Union since my Ph.D. days, 25 years or so ago, when I was working on earthquake faulting in Greece and Turkey. Its meetings were always the place that showcased geoscience at its most novel and exciting. It was the breadth of what was on offer that was so exhilarating. My doctoral studies had already opened up fairly wide vistas for me since my interest in Holocene earthquake activity also required an understanding of the Mediterranean's rich cultural history and the vagaries of millennial-scale climate fluctuations. Later, my research would distract me into farther-flung realms, such as volcanic faulting on Mount Etna, paleotsunamis along Aegean shores, even postglacial earthquakes in northern Scotland! Kindly colleagues would occasionally advise me to focus my efforts on a single substantive area of research, cautioning that my flighty research forays weren't conducive to climbing the academic ladder. I'm sure they were correct. Or would have been proved so if I hadn't been rescued by television.

  13. Social Change, Linguistic Change and Sociolinguistic Change in Received Pronunciation

    DEFF Research Database (Denmark)

    Fabricius, Anne H.

    2018-01-01

    This chapter summarises recent quantitative research on phonetic variation and change in Received Pronunciation (RP) as an elite sociolect, the vernacular of a multiplex socio-economically privileged group in the UK. The ‘elite sociolect’ is distinct from the ‘standard variety’, a term which should...... be reserved to refer to a socially generated mental ‘construct’, a set of expressed and tacit norms for ‘status-bearing’ language practice learned through the educational system and evident in the public domain. The chapter discusses variationist findings on word-final /t/, prevocalic /r/ and a range of vowel...... qualities. It also addresses evidence of sociolinguistic change, in the form of ongoing de-standardisation processes in the speech community of England, as well as the changing language-ideological and language-attitudinal place of RP in the sociolinguistic landscape....

  14. Mental health and coping strategies among social assistance receivers

    DEFF Research Database (Denmark)

    Andersen, John; Larsen, Jørgen Elm; Muller, Maja

    .g. in terms of participation in job training schemes and a requirement? of a certain minimum amount ( app 3 months ) of employment in the open labour market has increased. The arguments in the policy discource has been that lower benefits increases motivation and realistic, rational jobseeking behavior....... In short: lower benefit levels increases motivation which in turn increases labour market inclusion. This paper presents empirical results from an ongoing research project ( Consequences of living on the lowest social benefits financed by the Danish Social Council (Rådet for Socialt Udsatte) ,2008......-2011) about living conditions and how Danish citizens on the lowest benefits coped with their life situation. The longitudinal data followed the long term receivers of social assistance respondents over 1 year in order to observe changes in (selvreported) health, living conditions and coping strategies...

  15. Research Staff | Chemistry and Nanoscience Research | NREL

    Science.gov (United States)

    Research Staff Research Staff Research staff members in NREL's Chemistry and Nanoscience Center are Electrochemical Engineering and Materials Chemistry. For lead researcher contacts, see our research areas. For our : Chemistry and Nanoscience In addition to his position at NREL, Dr. van de Lagemaat is also a fellow of the

  16. Guidance on radiation received in space activities

    International Nuclear Information System (INIS)

    1989-01-01

    The purposes of this report, therefore, are to: re-examine the current guidelines and the philosophy adopted by NASA, estimate the risks to both men and women exposed to radiation in space, re-examine the estimates of radiation risks in outer space with special attention to SPE and to exposure to HZE particles, and examine what information may still be required and what research is needed. This report incorporates the changes in estimates of terrestrial radiation risks made since 1970 that appear to be acceptable and appropriate to the particular case of space missions. Since plans for a space station have been established and are a priority for NASA, this space mission will be used as one example for reference. The likely altitude and orbit for the proposed space station are 450 km and 28.5 degree, respectively. Therefore, estimates of the radiation environment for this mission can be made with more confidence than for some of the other missions. In this report, we have chosen to write more fully about certain subjects, for example, the eye, because they are of concern and because they have not been dealt with in such detail in other reports on radiation risks and protection. Since this report covers a number of different disciplines and specialized areas of research, a glossary is included. Radiation protection in space is as international a task as is the protection of radiation workers and the general population on earth. Kovalev, 1983, has noted that radiation protection in space is a pressing but complex problem. The recommendations in this report will require modifications as we learn more about the radiation environment in space and how to estimate radiation risks with greater precision. 450 refs

  17. Additive manufacturing of RF absorbers

    Science.gov (United States)

    Mills, Matthew S.

    The ability of additive manufacturing techniques to fabricate integrated electromagnetic absorbers tuned for specific radio frequency bands within structural composites allows for unique combinations of mechanical and electromagnetic properties. These composites and films can be used for RF shielding of sensitive electromagnetic components through in-plane and out-of-plane RF absorption. Structural composites are a common building block of many commercial platforms. These platforms may be placed in situations in which there is a need for embedded RF absorbing properties along with structural properties. Instead of adding radar absorbing treatments to the external surface of existing structures, which adds increased size, weight and cost; it could prove to be advantageous to integrate the microwave absorbing properties directly into the composite during the fabrication process. In this thesis, a method based on additive manufacturing techniques of composites structures with prescribed electromagnetic loss, within the frequency range 1 to 26GHz, is presented. This method utilizes screen printing and nScrypt micro dispensing to pattern a carbon based ink onto low loss substrates. The materials chosen for this study will be presented, and the fabrication technique that these materials went through to create RF absorbing structures will be described. The calibration methods used, the modeling of the RF structures, and the applications in which this technology can be utilized will also be presented.

  18. Proposal of a novel gravity-fed, particle-filled solar receiver

    Science.gov (United States)

    Johnson, Evan; Baker, Derek; Tari, Ilker

    2017-06-01

    Solar Thermal Electricity power plants utilizing solid particles as heat transfer and storage media have been proposed by several research groups, with studies citing benefits of increased thermal efficiency and lower cost. Several types of solid particle receivers have been proposed, with leading designs consisting of particles falling or suspended in air. A new solid particle receiver is proposed here, consisting of a receiver fully packed with particles flowing downward with gravity. Particle flow rate is regulated with an outlet valve. This Particle-Filled receiver concept is compared to other receiver designs, and initial cold and hot experiments are conducted. Mass flux values of up to 379 kg m-2 s-1 are demonstrated, and heat transfer coefficients between 136 and 251 W m-2 K-1 are found.

  19. RF measurements I: signal receiving techniques

    CERN Document Server

    Caspers, F

    2011-01-01

    For the characterization of components, systems and signals in the RF and microwave range, several dedicated instruments are in use. In this paper the fundamentals of the RF-signal sampling technique, which has found widespread applications in 'digital' oscilloscopes and sampling scopes, are discussed. The key element in these front-ends is the Schottky diode which can be used either as an RF mixer or as a single sampler. The spectrum analyser has become an absolutely indispensable tool for RF signal analysis. Here the front-end is the RF mixer as the RF section of modern spectrum analysers has a rather complex architecture. The reasons for this complexity and certain working principles as well as limitations are discussed. In addition, an overview of the development of scalar and vector signal analysers is given. For the determination of the noise temperature of a one-port and the noise figure of a two-port, basic concepts and relations are shown. A brief discussion of commonly used noise measurement techniq...

  20. [Trends in the utilization of food additives].

    Science.gov (United States)

    Szűcs, Viktória; Bánáti, Diána

    2013-11-17

    The frequent media reports on food additives weakened consumers' trust in food producers and food control authorities as well. Furthermore, consumers' uncertainty is also raised by the fact that they obtain their information from inadequate, mistrustful sources and, therefore, consumers might avoid the consumption of certain foodstuffs. While food producers may react by replacing artificial components by natural ones, they try to emphasize the favourable characteristics of their products. The authors describe the main trends and efforts related to food additives. On the basis of the overview it can be concluded that - besides taking into consideration consumers' needs - product development and research directions are promising. Food producers' efforts may help to restore consumer confidence and trust and they may help them to have informed choice.