Investigation of the behaviour of a LILW superficial repository under aircraft impact

International Nuclear Information System (INIS)

Lo Frano, Rosa; Stefanini, Lorenzo

2016-01-01

Highlights: • Safety assessment of a LILW superficial repository. • Investigation of the consequences of an aircraft impact with fuel burning. • Experimental material properties. • Numerical simulation of aircraft impact with fuel burning accident by MSC.MARC"© code. • Demonstration that the overall integrity resulted is guaranteed. - Abstract: Safety and security are the two fundamental aspects to guarantee when designing a LILW superficial repository. Because of its safety concern, we have to prove, and build confidence in, the primary and secondary consequences of the crashing will be acceptable. These goals are obtained generally by means of safety assessment supported by calculations. This study is intended to investigate the performance of a superficial repository subjected to aircraft impact and fuel burning. To the purpose a superficial repository similar to that of El Cabril has been considered. Moreover to be confident the facility is safe and that the consequences of such a type of accident on the environment and humans are negligible, an appropriate safety assessment was carried out. The potential damage that aircraft impact could bring into the repository has been therefore analysed and discussed. To attain the intent load functions, calculated according to the Riera approach, and the maximum temperature reached by fuel during its combustion have been considered. FEM (thermo-mechanical) simulations have been done, by MSC"© Marc code, assuming damaging phenomena of concrete and material properties variation with the temperature. The obtained results showed that an empty superficial repository with a wall thickness, ranging from 0.7 to 1 m, is not sufficient to avoid penetration. Nevertheless even in presence of a reduced strength and of (cone) cracking and plugging, the overall integrity resulted guaranteed.

Investigation of the behaviour of a LILW superficial repository under aircraft impact

Energy Technology Data Exchange (ETDEWEB)

Lo Frano, Rosa, E-mail: rosa.lofrano@ing.unipi.it; Stefanini, Lorenzo

2016-04-15

Highlights: • Safety assessment of a LILW superficial repository. • Investigation of the consequences of an aircraft impact with fuel burning. • Experimental material properties. • Numerical simulation of aircraft impact with fuel burning accident by MSC.MARC{sup ©} code. • Demonstration that the overall integrity resulted is guaranteed. - Abstract: Safety and security are the two fundamental aspects to guarantee when designing a LILW superficial repository. Because of its safety concern, we have to prove, and build confidence in, the primary and secondary consequences of the crashing will be acceptable. These goals are obtained generally by means of safety assessment supported by calculations. This study is intended to investigate the performance of a superficial repository subjected to aircraft impact and fuel burning. To the purpose a superficial repository similar to that of El Cabril has been considered. Moreover to be confident the facility is safe and that the consequences of such a type of accident on the environment and humans are negligible, an appropriate safety assessment was carried out. The potential damage that aircraft impact could bring into the repository has been therefore analysed and discussed. To attain the intent load functions, calculated according to the Riera approach, and the maximum temperature reached by fuel during its combustion have been considered. FEM (thermo-mechanical) simulations have been done, by MSC{sup ©} Marc code, assuming damaging phenomena of concrete and material properties variation with the temperature. The obtained results showed that an empty superficial repository with a wall thickness, ranging from 0.7 to 1 m, is not sufficient to avoid penetration. Nevertheless even in presence of a reduced strength and of (cone) cracking and plugging, the overall integrity resulted guaranteed.

Addressing concerns about the agricultural impacts of siting a nuclear waste repository in Texas

International Nuclear Information System (INIS)

Boryczka, M.; Darrough, B.

1986-01-01

Public concerns related to the siting of a nuclear repository have included the potential impacts to specific economic sectors. In Texas, local residents have expressed concern about how a repository will affect agriculture. Several major questions have arisen with respect to this issue including: 1) how will a repository's requirements for land and water affect agriculture, 2) how will a repository affect agricultural land values, and 3) how will actual or perceived contamination of locally grown products affect their marketability? This paper describes the concerns raised by local residents and discusses the approach to analyzing the concerns identified. An evaluation of agricultural impacts has been prepared for the Department of Energy's Enviromental Assessment (EA) documents. In addition, activities needed to further evaluate these impacts are planned for site characterization. Both the current analysis and planned activities are described

Social impact mitigation and nuclear waste repository siting

International Nuclear Information System (INIS)

Peelle, E.

1980-01-01

Some aspects of the socioeconomic impacts of siting, constructing, and operating radioactive waste repositories in rural areas are discussed. These include public perceptions of high risk and uncertainty; limited benefits and no incentives; dissociations of costs and benefits; remoteness and inaccessibility of the decision making process for large energy facilities; no institutions to provide protection and accountability for those who may be affected by the siting; the fact that not all risks or impacts are fully mitigable; and constraints on DOE's present ability or authority to mitigate impacts

National Radwaste Repository Mochovce

International Nuclear Information System (INIS)

2000-01-01

In this leaflet the National Radioactive Waste Repository in Mochovce (Repository) is described. The Mochovce National Radioactive Waste Repository is a surface multi-barrier type storage facility for solid and treated solidified radioactive wastes generated from the Slovak Republic nuclear power plants operation and decommissioning, research institutes, laboratories and hospitals. The Repository comprises a system of single- and double-row storage boxes. The first double-row is enclosed by a steel-structure building. The 18 x 6 x 5.5 m storage boxes are made of reinforced concrete. The wall thickness is 600 mm. Two-double-rows, i.e. 80 storage boxes were built as part of Stage I (1 row = 20 storage boxes). Each storage box has a storage capacity of 90 fibre concrete containers of 3.1 m 3 volume. The total storage capacity is 7200 containers with the overall storage volume of 22320 m 3

Main organic materials in a repository for high level radioactive waste

International Nuclear Information System (INIS)

Hallbeck, Lotta; Grive, Mireia; Gaona, Xavier; Duro, Lara; Bruno, Jordi

2007-11-01

A compilation of the origin and composition of organic material possibly left in a repository is made. Recommendations of precautions and actions for the different material are listed as well. As a brief summary, the different categories of organic material of relevance for the repository are: 1. Microorganisms. Their effect would be mainly a reduction of the redox potential in the initial stages after the repository closure. They may contribute to the depletion of the oxygen entrapped due to the repository construction. This effect would not jeopardize the stability of the repository. If the dominating microorganisms in the anaerobic environment are sulphate-reducing bacteria, oxidation of organic material would lead to formation of HS - . The produced sulphide can corrode copper under anaerobic conditions, if it reaches the canisters. Another effect of microorganisms would be the increase of the complexing capacity of the groundwater due to excreted metabolites. The impact of these compounds is not yet clear, although it will surely not be very important, due to the low amounts of the excreted substances. 2. Materials in the ventilation air. Their effect will probably be a contribution to the maintenance of reducing conditions in the area, although it is likely that this effect will be minimal or negligible. 3. Construction materials. Among them we can highlight organic materials present in concrete, asphalt, bentonite and wood. The most important compounds from the repository safety perspective will be those hydrocarbons from asphalt that may contribute to decreasing the redox potential around the repository, and the products of degradation of cellulose. This last category of compounds may contribute to enhance the complexing capacity of the groundwater around the repository and it is recommended to minimize the amount of cellulose left in the repository. 4. Fuels and engine emissions. No important effects from these organics in the repository are expected

Main organic materials in a repository for high level radioactive waste

Energy Technology Data Exchange (ETDEWEB)

Hallbeck, Lotta [Vita vegrandis, Hindaas (Sweden); Grive, Mireia; Gaona, Xavier; Duro, Lara; Bruno, Jordi [Enviros Consulting, Valldoreix, Barcelona (Spain)

2007-11-15

A compilation of the origin and composition of organic material possibly left in a repository is made. Recommendations of precautions and actions for the different material are listed as well. As a brief summary, the different categories of organic material of relevance for the repository are: 1. Microorganisms. Their effect would be mainly a reduction of the redox potential in the initial stages after the repository closure. They may contribute to the depletion of the oxygen entrapped due to the repository construction. This effect would not jeopardize the stability of the repository. If the dominating microorganisms in the anaerobic environment are sulphate-reducing bacteria, oxidation of organic material would lead to formation of HS{sup -}. The produced sulphide can corrode copper under anaerobic conditions, if it reaches the canisters. Another effect of microorganisms would be the increase of the complexing capacity of the groundwater due to excreted metabolites. The impact of these compounds is not yet clear, although it will surely not be very important, due to the low amounts of the excreted substances. 2. Materials in the ventilation air. Their effect will probably be a contribution to the maintenance of reducing conditions in the area, although it is likely that this effect will be minimal or negligible. 3. Construction materials. Among them we can highlight organic materials present in concrete, asphalt, bentonite and wood. The most important compounds from the repository safety perspective will be those hydrocarbons from asphalt that may contribute to decreasing the redox potential around the repository, and the products of degradation of cellulose. This last category of compounds may contribute to enhance the complexing capacity of the groundwater around the repository and it is recommended to minimize the amount of cellulose left in the repository. 4. Fuels and engine emissions. No important effects from these organics in the repository are expected

Emplacement feasibility of a multi-tier, expanded capacity repository at Yucca Mountain, Nevada USA

International Nuclear Information System (INIS)

Apted, Michael; Kessler, John; Fairhurst, Charles

2008-01-01

A geological repository at Yucca Mountain has been proposed for the disposal of spent fuel from the US commercial reactors and other radioactive waste. A legislative capacity of 70,000 MTHM has been set by the Nuclear Waste Policy Act of 1982, including 63,000 MTHM of commercial spent nuclear fuel (CSNF), the projected amount of CSNF that will be produced by about 2014. Policy issues remain as to how to handle waste that is generated beyond 2014 from a growing nuclear industry in the US. The Electric Power Research Institute (EPRI) is independently evaluating the technical, rather than legislative, limit of CSNF that could be safely disposed at Yucca Mountain. Geological, thermal management, safety and cost factors have been recently evaluated by EPRI (2006; 2007) for grouped emplacement drifts and/or a multi-tier repository. EPRI's evaluation of emplacement feasibility for a multi-tier concept is described here. Expanded capacity concepts as envisioned for Yucca Mountain (EPRI, 2006; 2007) assume excavation of one or two additional levels of drifts parallel to or above and/or below the original drift excavations. For the latter multi-tier concept each 'tier' or 'level' would essentially replicate the original layer with a 30-m separation between tiers. This arrangement essentially doubles or triples the capacity of the repository for a two- or three-tier design, respectively. The main issues that affect the feasibility of expanded capacity design are; (i) ventilation requirements; (ii) radiation hazards; (iii) thermal and thermo-mechanical constraints. (i)Ventilation: The repository design involves waste packages mounted in close proximity to each other in 600-m long drifts that remain open and actively ventilated for at least 50-100 years. Analyses,conservatively assuming that all three repository levels operate simultaneously, indicate no technological obstacles in meeting ventilation requirements for sustained simultaneous operation ba sed on current industrial

Environmental Impacts of Transportation to the Potential Repository at Yucca Mountain

International Nuclear Information System (INIS)

Sweeney, R.L.; Best, R.; Bolton, P.; Adams, P.

2002-01-01

The Environmental Impact Statement for a Geologic Repository for the Disposal of Spent Nuclear Fuel and High-Level Radioactive Waste at Yucca Mountain, Nye County, Nevada analyzes a Proposed Action to construct, operate, monitor, and eventually close a geologic repository for the disposal of spent nuclear fuel and high-level radioactive waste. As part of the Proposed Action, the EIS analyzes the potential impacts of transporting commercial and DOE spent nuclear fuel and high-level radioactive waste to Yucca Mountain from 77 sites across the United States. The analysis includes information on the comparative impacts of transporting these materials by truck and rail and discusses the impacts of building a rail line or using heavy-haul trucks to move rail casks from a mainline railroad in Nevada to the site. This paper provides an overview of the analyses and the potential impacts of these transportation activities. The potential transportation impacts were looked at from two perspectives: transportation of spent nuclear fuel and high-level radioactive waste by legal-weight truck or by rail on a national scale and impacts specific to Nevada from the transportation of these materials from the State borders to the Yucca Mountain site. In order to address the range of impacts that could result from the most likely modes, legal-weight truck and rail, the EIS employed two analytical scenarios--mostly legal-weight truck and mostly rail. Estimated national transportation impacts were based on 24 years of transportation activities. Approximately 8 fatalities could occur from all causes in the nationwide general population from incident-free transportation activities of the mostly legal-weight truck scenario and about 4 from the mostly rail scenario. The analysis examined the radiological consequences under the maximum foreseeable accident scenario and also overall accident risk. The overall accident risk over the 24 year period would be about 0.0002 latent cancer fatality for

Connecting the pieces: using ORCIDs to improve research impact and repositories

KAUST Repository

Baessa, Mohamed A.

2015-05-19

Quantitative data are crucial in the assessment of research impact in the academic world. However, as a young university created in 2009, King Abdullah University of Science and Technology (KAUST) needs to aggregate bibliometrics from researchers coming from diverse origins, not necessarily with the proper affiliations. In this context, the University has launched an institutional repository in September 2012 with the objectives of creating a home for the intellectual outputs of KAUST researchers. Later, the university adopted the first mandated institutional open access policy in the Arab region, effective June 31, 2014. Several projects were then initiated in order to accurately identify the research being done by KAUST authors and bring it into the repository in accordance with the open access policy. Integration with ORCID has been a key element in this process and the best way to ensure data quality for researcher’s scientific contributions. It included the systematic inclusion and creation, if necessary, of ORCID identifiers in the existing repository system, an institutional membership in ORCID, and the creation of dedicated integration tools. In addition and in cooperation with the Office of Research Evaluation, the Library worked at implementing a Current Research Information System (CRIS) as a standardized common resource to monitor KAUST research outputs. We will present our findings about the CRIS implementation, the ORCID API, the repository statistics as well as our approach in conducting the assessment of research impact in terms of usage by the global research community.

The projected environmental impacts of transportation of radioactive material to the first United States repository site

International Nuclear Information System (INIS)

Cashwell, J.W.; Neuhauser, K.S.; Reardon, P.C.; McNair, G.W.

1987-01-01

The relative national environmental impacts of transporting spent fuel and other nuclear wastes to each of 9 candidate repository sites in the United States were analyzed for the 26-year period of repository operation. Two scenarios were examined for each repository: 1) shipment of 5-year-old spent fuel and Defence High-Level Waste (DHLW) directly from their points of origin to a repository (reference case); and 2) shipment of 5-year-old spent fuel to a Monitored Retrievable Storage (MRS) facility and shipment (by dedicated rail) of 10-year-old consolidated spent fuel from the MRS to a repository. Transport by either all truck or all rail from the points of origin were analyzed as bounding cases. The computational system used to analyze these impacts included the WASTES II logistics code and the RADTRAN III risk analysis code. The radiological risks for the reference case increased as the total shipment miles to a repository increased for truck; the risks also increased with mileage for rail but at a lower rate. For the MRS scenario the differences between repository sites were less pronounced for both modal options, because of the reduction in total shipment miles possible with the large dedicated rail casks. All the risks reported are small in comparison to the radiological risks due to 'natural background'

Oxidation-reduction reactions. Overview and implications for repository studies

International Nuclear Information System (INIS)

Apted, Michael J.; Arthur, Randolph C.; Sasamoto, Hiroshi; Yui, Mikazu; Iwatsuki, Teruki

2001-02-01

The purpose of this report is to provide a survey and review on oxidation-reduction ('redox') reactions, with particular emphasis on implications for disposal of high-level waste (HLW) in deep geological formations. As an overview, the focus is on basic principles, problems, and proposed research related specifically to the assessment of redox for a HLW repository in Japan. For a more comprehensive treatment of redox and the myriad associated issues, the reader is directed to the cited textbooks used as primary references in this report. Low redox conditions in deep geological formations is a key assumption in the 'Second Progress Report on Research and Development for the Geological Disposal of HLW in Japan' (hereafter called H12'). The release behavior of multi-valent radioelements (e.g., Tc, Se, U, Pu, Np), as well as daughter radioelements of these radioelements, from a deep geological repository are sensitively related to redox conditions. Furthermore, the performance of certain barrier materials, such as overpack and buffer, may be impacted by redox conditions. Given this importance, this report summarizes some key topics for future technical studies supporting site characterization and repository performance as follows: To fully test the conceptual models for system Eh, it will be necessary to measure and evaluate trace element and isotopic information of both coexisting groundwater and reactive minerals of candidate rocks. Because of importance of volatile species (e.g., O 2 , H 2 etc.) in redox reactions, and given the high total pressure of a repository located 500 to 1000 meter deep, laboratory investigations of redox will necessarily require use of pressurized test devices that can fully simulate repository conditions. The stability (redox capacity) of the repository system with respect to potential changes in redox boundary condition induced by oxidizing waters intrusion should be established experimentally. An overall conceptual model that unifies

Methods for assessing the socioeconomic impacts of large-scale resource developments: implications for nuclear repository siting

International Nuclear Information System (INIS)

Murdock, S.H.; Leistritz, F.L.

1983-03-01

An overview of the major methods presently available for assessing the socioeconomic impacts of large-scale resource developments and includes discussion of the implications and applications of such methods for nuclear-waste-repository siting are provided. The report: (1) summarizes conceptual approaches underlying, and methodological alternatives for, the conduct of impact assessments in each substantive area, and then enumerates advantages and disadvantages of each alternative; (2) describes factors related to the impact-assessment process, impact events, and the characteristics of rural areas that affect the magnitude and distribution of impacts and the assessment of impacts in each area; (3) provides a detailed review of those methodologies actually used in impact assessment for each area, describes advantages and problems encountered in the use of each method, and identifies the frequency of use and the general level of acceptance of each technique; and (4) summarizes the implications of each area of projection for the repository-siting process, the applicability of the methods for each area to the special and standard features of repositories, and makes general recommendations concerning specific methods and procedures that should be incorporated in assessments for siting areas

Connecting the pieces: Using ORCIDs to improve research impact and repositories.

Science.gov (United States)

Baessa, Mohamed; Lery, Thibaut; Grenz, Daryl; Vijayakumar, J K

2015-01-01

Quantitative data are crucial in the assessment of research impact in the academic world. However, as a young university created in 2009, King Abdullah University of Science and Technology (KAUST) needs to aggregate bibliometrics from researchers coming from diverse origins, not necessarily with the proper affiliations. In this context, the University has launched an institutional repository in September 2012 with the objectives of creating a home for the intellectual outputs of KAUST researchers. Later, the university adopted the first mandated institutional open access policy in the Arab region, effective June 31, 2014. Several projects were then initiated in order to accurately identify the research being done by KAUST authors and bring it into the repository in accordance with the open access policy. Integration with ORCID has been a key element in this process and the best way to ensure data quality for researcher's scientific contributions. It included the systematic inclusion and creation, if necessary, of ORCID identifiers in the existing repository system, an institutional membership in ORCID, and the creation of dedicated integration tools. In addition and in cooperation with the Office of Research Evaluation, the Library worked at implementing a Current Research Information System (CRIS) as a standardized common resource to monitor KAUST research outputs. We will present our findings about the CRIS implementation, the ORCID API, the repository statistics as well as our approach in conducting the assessment of research impact in terms of usage by the global research community.

State-of-the-art for evaluating the potential impact of flooding on a radioactive waste repository

International Nuclear Information System (INIS)

1980-01-01

This report is a review of the state-of-the-art for evaluating the potential impact of flooding on a deep radioactive-waste repository, namely, for predicting the future occurrence of catastrophic flooding and for estimating the effect of such flooding on waste containment characteristics. Several detrimental effects are identified: flooding can increase groundwater seepage velocities through a repository within the framework of the existing hydrologic system and thus increase the rate of radioactive-waste leakage to the biosphere; flooding may alter repository hydrology by reversing flow gradients, relocating sources of groundwater recharge and discharge, or shortening seepage paths, thereby producing unpredictable leakage; saturation of a vadose-zone repository during flooding can increase groundwater seepage velocities by several orders of magnitude; and flooding can damage repository-media containment properties by inducing seismic or chemical instability or increasing fracture permeability in relatively shallow repository rock as a result of redistributing in-situ stresses. Short-term flooding frequency and magnitude can be predicted statistically by analyzing historical records of flooding. However, long-term flooding events that could damage a permanent repository cannot be predicted with confidence because the geologic record is neither unique nor sufficienly complete for statistical analysis. It is more important to identify parameters characterizing containment properties (such as permeability, groundwater gradient, and shortest seepage path length to the biosphere) that could be affected by future flooding, estimate the maximum magnitude of flooding that could occur within the life of the repository by examining the geologic record, and determine the impact such flooding could have on the parameter values

Preliminary safety evaluation of an aircraft impact on a near-surface radioactive waste repository

Energy Technology Data Exchange (ETDEWEB)

Lo Frano, R.; Forasassi, G.; Pugliese, G. [Department of Industrial and Civil Engineering (DICI), University of Pisa, Pisa (Italy)

2013-07-01

The aircraft impact accident has become very significant in the design of a nuclear facilities, particularly, after the tragic September 2001 event, that raised the public concern about the potential damaging effects that the impact of a large civilian airplane could bring in safety relevant structures. The aim of this study is therefore to preliminarily evaluate the global response and the structural effects induced by the impact of a military or commercial airplane (actually considered as a 'beyond design basis' event) into a near surface radioactive waste (RWs) disposal facility. The safety evaluation was carried out according to the International safety and design guidelines and in agreement with the stress tests requirements for the security track. To achieve the purpose, a lay out and a scheme of a possible near surface repository, like for example those of the El Cabril one, were taken into account. In order to preliminarily perform a reliable analysis of such a large-scale structure and to determine the structural effects induced by such a types of impulsive loads, a realistic, but still operable, numerical model with suitable materials characteristics was implemented by means of FEM codes. In the carried out structural analyses, the RWs repository was considered a 'robust' target, due to its thicker walls and main constitutive materials (steel and reinforced concrete). In addition to adequately represent the dynamic response of repository under crashing, relevant physical phenomena (i.e. penetration, spalling, etc.) were simulated and analysed. The preliminary assessment of the effects induced by the dynamic/impulsive loads allowed generally to verify the residual strength capability of the repository considered. The obtained preliminary results highlighted a remarkable potential to withstand the impact of military/large commercial aircraft, even in presence of ongoing concrete progressive failure (some penetration and spalling of the

Environmental impact assessments and geological repositories for radioactive waste

International Nuclear Information System (INIS)

O'Sullivan, P.; McKirdy, B.; Askarieh, M.; Bond, A.; Russell, S.

1999-01-01

Since 1985 it has been obligatory that facilities in the European Union designed for the permanent storage or disposal of radioactive waste be assessed to determine their effects on the environment. This assessment must be undertaken in advance of any decision by national authorities to give consent for development work to proceed. Member States are given wide discretion on how the above requirements are implemented in practice, e.g. the relevant European Council Directives call for the results of the environmental assessment to be made available to the public before development consent is granted but the detailed arrangements for dissemination of such information and procedures for public consultation are determined by individual Member States. Although the Directives require an assessment of the direct and indirect effects of a project on human beings and on various elements of the natural environment, they are non-specific as to what particular impacts should be addressed, particularly as regards the effects of a project on human beings. Therefore, for example, each Member State may decide whether or not social, health and economic impacts should be included in the assessment. This paper discusses the above issues. It proposes a model approach to environmental impact assessment in the context of geological repositories, including the role of the assessment on the overall decision processes for repository development, the scope and content of the assessment report, and approaches to public involvement

Siting the nation's first high-level nuclear waste repository: Social impacts for Utah

International Nuclear Information System (INIS)

Olshansky, S.J.

1986-01-01

The siting of a high-level nuclear waste repository in the United States has been an issue of great controversy, particulary for the states under consideration. In addition to concerns expressed about the geological stability of the proposed sites, numerous social issues have been raised by the general public--most of which have been addressed by the draft environmental impact statements. Among the social impacts raised by the Department of Engery and the general public, those receiving the greatest attention were the potential influence of the repository on local economics, tourism, and the health status of the local residents. The major issues of interest in the present study include 1) the effects of respondent knowledge of nuclear waste disposal issues on opinions of health effects and tourism, particularly as they are affected by visitation patterns, and 2) the effects of occupation and education (in particular) on knowledge of nuclear waste disposal issues and opinions on technical and non-technical aspects of siting the repository. Preliminary results indicate that only about 40 percent of the respondents have visited the national parks in southeastern Utah, but over 70 percent feel they are informed about the issues associated with siting the repository. Over 60 percent of the respondents were very concerned about the possible negative effect the repository could have on jobs, tourism, health effects, and environmental quality. Cross-tabulations indicate that the respondents self rating on knowledge of nuclear disposal issues has a statistically significant influence on responses to socioeconomic issues, yet the same self rating scale is significantly influenced by the frequency with which respondents have visited the national parks in southeastern Utah

Perceived risk, stigma, and potential economic impacts of a high-level nuclear waste repository in Nevada

International Nuclear Information System (INIS)

Slovic, P.; Layman, M.; Kraus, N.; Flynn, J.; Chalmers, J.; Gesell, G.

1991-01-01

This study investigates the potential impacts of the proposed nuclear waste repository at Yucca Mountain, Nevada, upon tourism, retirement and job-related migration, and business development in Las Vegas and the state. Adverse impacts may be expected to result from perceptions of risk, stigmatization, and socially amplified reactions to 'unfortunate events' associated with the repository (major and minor accidents, discoveries of radiation releases, evidence of mismanagement, attempts to sabotage or disrupt the facility, etc.). The conceptual underpinnings of risk perception, stigmatization, and social amplification are discussed and empirical data are presented to demonstrate how nuclear images associated with Las Vegas and the State of Nevada might trigger adverse economic effects. The possibility that intense negative imagery associated with the repository may cause significant harm to Nevada's economy can no longer be ignored by serious attempts to assess the risks and impacts of this unique facility. The behavioral processes described here appear relevant as well to the social impact assessment of any proposed facility that produces, uses, transports, or disposes of hazardous materials

Perceived risk, stigma, and potential economic impacts of a high-level nuclear waste repository in Nevada.

Science.gov (United States)

Slovic, P; Layman, M; Kraus, N; Flynn, J; Chalmers, J; Gesell, G

1991-12-01

This study investigates the potential impacts of the proposed nuclear waste repository at Yucca Mountain, Nevada, upon tourism, retirement and job-related migration, and business development in Las Vegas and the state. Adverse impacts may be expected to result from perceptions of risk, stigmatization, and socially amplified reactions to "unfortunate events" associated with the repository (major and minor accidents, discoveries of radiation releases, evidence of mismanagement, attempts to sabotage or disrupt the facility, etc.). The conceptual underpinnings of risk perception, stigmatization, and social amplification are discussed and empirical data are presented to demonstrate how nuclear images associated with Las Vegas and the State of Nevada might trigger adverse economic effects. The possibility that intense negative imagery associated with the repository may cause significant harm to Nevada's economy can no longer be ignored by serious attempts to assess the risks and impacts of this unique facility. The behavioral processes described here appear relevant as well to the social impact assessment of any proposed facility that produces, uses, transports, or disposes of hazardous materials.

Impact on geologic repository usage from limited actinide recycle in pressurized light water reactors

International Nuclear Information System (INIS)

Wigeland, Roald A.; Bauer, Theodore H.; Hill, Robert N.; Stillman, John A.

2007-01-01

A project has been conducted as part of the U.S. Department of Energy Advanced Fuel Cycle Initiative to evaluate the impact of limited actinide recycling in light water reactors on the utilization of a geologic repository where loading of the repository is constrained by the decay heat of the emplaced materials. In this study, it was assumed that spent PWR fuel was processed, removing the uranium, plutonium, americium, and neptunium, along with the fission products cesium and strontium. Previous work had demonstrated that these elements were responsible for limiting loading in the repository based on thermal constraints. The plutonium, americium, and neptunium were recycled in a PWR, with process waste and spent recycled fuel being sent to the repository. The cesium and strontium were placed in separate storage for 100-300 years to allow for decay prior to disposal. The study examined the effect of single and multiple recycles of the recovered plutonium, americium, and neptunium, as well as different processing delay times. The potential benefit to the repository was measured by the increase in utilization of repository space as indicated by the allowable linear loading in the repository drifts (tunnels). The results showed that limited recycling would provide only a small fraction of the benefit that could be achieved with repeated processing and recycling, as is possible in fast neutron reactors. (author)

Connecting the pieces: using ORCIDs to improve research impact and repositories

KAUST Repository

Baessa, Mohamed A.; Lery, Thibaut L.; Vijayakumar, J.K.; Grenz, Daryl M.

2015-01-01

Integration with ORCID has been a key element in this process and the best way to ensure data quality for researcher’s scientific contributions. It included the systematic inclusion and creation, if necessary, of ORCID identifiers in the existing repository system, an institutional membership in ORCID, and the creation of dedicated integration tools. In addition and in cooperation with the Office of Research Evaluation, the Library worked at implementing a Current Research Information System (CRIS) as a standardized common resource to monitor KAUST research outputs. We will present our findings about the CRIS implementation, the ORCID API, the repository statistics as well as our approach in conducting the assessment of research impact in terms of usage by the global research community.

Impact of thermal constraints on the optimal design of high-level waste repositories in geologic media

Energy Technology Data Exchange (ETDEWEB)

Malbrain, C; Lester, R K [Massachusetts Inst. of Tech., Cambridge (USA). Dept. of Nuclear Engineering

1982-12-01

An approximate, semi-analytical heat conduction model for predicting the time-dependent temperature distribution in the region of a high-level waste repository has been developed. The model provides the basis for a systematic, inexpensive examination of the impact of several independent thermal design constraints on key repository design parameters and for determining the optimal set of design parameters which satisfy these constraints. Illustrative calculations have been carried out for conceptual repository designs for spent pressurized water reactor (PWR) fuel and reprocessed PWR high-level waste in salt and granite media.

Environmental impact assessments and geological repositories: A model process

International Nuclear Information System (INIS)

Webster, S.

2000-01-01

In a recent study carried out for the European Commission, the scope and application of environmental impact assessment (EIA) legislation and current EIA practice in European Union Member States and applicant countries of Central and Eastern Europe was investigated, specifically in relation to the geological disposal of radioactive waste. This paper reports the study's investigations into a model approach to EIA in the context of geological repositories, including the role of the assessment in the overall decision processes and public involvement. (author)

USGS studies of physical--chemical relationships in salt repositories

International Nuclear Information System (INIS)

Stewart, D.B.

1977-01-01

The amount and physical properties of brine that can occur in salt repositories at elevated temperatures and pressures adjacent to waste-bearing cannisters will have considerable impact on the mechanical strength and stability of the repository. Brine will form readily from H 2 O absorbed on surfaces, diffusion along grain boundaries, movement of fluid inclusions, dehydration of hydrous minerals such as gypsum, polyhalite or clays, or even from leakage through failed shaft openings. A T-P diagram for NaCl--H 2 O shows the limits for coexisting solid-liquid-gas assemblages in salt repositories. Isobaric T-X diagrams are included to show compositional details at pressures below the critical point and above it. Properties of the fluid phases such as volume, density, heat capacity, enthalpy, viscosity, surface tension, osmotic coefficients, etc. can be well described (>0.01% to 2 O. Because aggregates of solids are mechanically weakened by interstitial liquid, determination of mechanical properties of brine-bearing aggregates is needed. A maximum of one third by weight of brine (not H 2 O), and probably much less, will destroy rock strength

Final Systems Development Report for the Clark County Socioeconomic Impact Assessment of the Proposed High-Level Nuclear Waste Repository at Yucca Mountain, NV

Energy Technology Data Exchange (ETDEWEB)

NONE

1992-06-18

The Systems Development Report represents the third major step in the Clark County Socioeconomic Impact Assessment of the Proposed High-Level Nuclear Waste Repository at Yucca Mound Nevada. The first of these steps was to forge a Research Design that would serve as a guide for the overall research process. The second step was the construction of the Base Case, the purpose of which was to describe existing conditions in Clark County in the specified analytic areas of Economic-Demographic/Fiscal, Emergency Planning and Management, Transportation and Sociocultural analysis. The base case description will serve as a basis for assessing changes in these topic areas that might result from the Yucca Mountain project. These changes will be assessed by analyzing conditions with and without repository development in the county. Prior to performing such assessments, however, the snapshot type of data found in the base case must be operationalized or systematized to allow for more dynamic data utilization. In other words, a data system that can be used to analyze the consequences of the introduction of different variables (or variable values) in the Clark County context must be constructed. Such a system must be capable of being updated through subsequent data collection and monitoring efforts to both provide a rolling base case and supply information necessary to construct trend analyses. For example, during the Impact Assessment phase of the study process, the without repository analysis is accomplished by analyzing growth for the county given existing conditions and likely trends. These data are then compared to the with Yucca Mountain project conditions anticipated for the county. Similarly, once the emergency planning management and response needs associated with the repository are described, these needs will be juxtaposed against existing (and various future) capacity(ies) in order to determine the nature and magnitude of impacts in this analytic area. Analogous tasks

The influence of discontinuity interfaces on physical, chemical and mechanical properties and the behaviour of repository backfill materials (Czech Republic)

International Nuclear Information System (INIS)

Slovak, J.; Pacovsky, J.

2000-01-01

Safe disposal (isolation) of high radioactive waste requires solving many non-standard engineering problems which are complicated due to the demand of reliability of underground repository construction with respect to long term safety. Required durability of most engineered structures is about 10-100 years. Proposed underground repository construction must guarantee the demand for safe disposal of highly radioactive waste for 100 thousand to 1 million years. Extrapolation methodologies are developed and applied on findings of experimental research. One of the techniques is used in geotechnical sciences to determine data needed for the extrapolation the cyclical impact of different processes. Repeated impact of the same action or diversifying the different actions can accelerate some processes which are slow at normal conditions. Long term cyclical impact of moisture on a section of the barrier system (loaded by temperature) may cause changes of the quality of properties, such as permeability, sorption capacity, thermal conductivity and swelling capacity. (author)

Economic and fiscal impacts of large-scale development projects: implications for nuclear waste repositories

International Nuclear Information System (INIS)

Leistritz, F.L.; Murdock, S.H.; Texas A and M Univ., College Station)

1982-01-01

This paper deals with the local economic and fiscal implications of siting high-level nuclear waste repositories in rural areas. The economic and fiscal effects of repository development fall into two categories: (1) standard impacts similar to those that would be associated with developing any large-scale industrial facility in an isolated area; (2) special impacts that result from the hazardous nature of the nuclear materials stored and from federal ownership of the facility. Standard economic and fiscal impacts include employment effects (direct and secondary), local income changes, alterations in community price structures, effects on community services, and changes in revenues and costs for local jurisdictions. Special impacts include the possibility of diminished activity in other basic economic sectors, negative effects on the area's long-term growth prospects and a consequent dampening of investment in the local trade an service sectors, additional costs for local jurisdictions (e.g., for preparing evacuation plans), and limited local tax revenues resulting from the tax-exempt status of the facility. These special effects are difficult to quantify and require additional analysis. 47 references, 1 figure, 4 tables

Evaluation of health and safety impacts of defense high-level waste in geologic repositories

International Nuclear Information System (INIS)

Smith, E.D.; Kocher, D.C.; Witherspoon, J.P.

1985-02-01

Pursuant to the requirement of the Nuclear Waste Policy Act of 1982 that the President evaluate the use of commercial high-level waste repositories for the disposal of defense high-level wastes, a comparative assessment has been performed of the potential health and safety impacts of disposal of defense wastes in commercial or defense-only repositories. Simplified models were used to make quantitative estimates of both long- and short-term health and safety impacts of several options for defense high-level waste disposal. The results indicate that potential health and safety impacts are not likely to vary significantly among the different disposal options for defense wastes. Estimated long-term health and safety impacts from all defense-waste disposal options are somewhat less than those from commercial waste disposal, while short-term health and safety impacts appear to be insensitive to the differences between defense and commercial wastes. In all cases, potential health and safety impacts are small because of the need to meet stringent standards promulgated by the US Environmental Protection Agency and the US Nuclear Regulatory Commission. We conclude that health and safety impacts should not be a significant factor in the choice of a disposal option for defense high-level wastes. 20 references, 14 tables

Draft environmental impact statement. High-level waste repository site suitability criteria

International Nuclear Information System (INIS)

1978-01-01

The purpose of HLWRSSC is to present guidelines which will help in the development of safe waste management schemes. Current regulations require solidification of all high-level waste within 5 years of their generation and transfer to a Federal waste repository within 10 years. Development of the proposed HLWRSSC is part of the overall NRC program to close the ''back end'' of the commercial LWR fuel cycle. In this document, the need for the HLWRSSC is reviewed, and the national energy policy, the need for electrical energy, and the nuclear fuel cycle are discussed. Considerations for HLWRSSC are presented, including the nature of the repository, important site-related factors, and radiological risk assessment methodology. Radiological and nonradiological environment impacts associated with the HLWRSSC are defined. Alternatives to the criteria are presented, and the cost-benefit-risk evaluation is reviewed

Evaluation of commercial repository capacity for the disposal of defense high-level waste. Comments and responses for DOE/DP--0020

International Nuclear Information System (INIS)

1985-12-01

The Nuclear Waste Policy Act of 1982 (Public Law 97-425) requires that the President evaluate the use of disposal capacity at one or more repositories to be developed for permanent disposal of civilian spent nuclear fuel and high-level radioactive waste for the disposal of defense high-level radioactive waste. The Department of Energy prepared a report titled ''An Evaluation of Commercial Repository Capacity for the Disposal of Defense High-Level Waste,'' DOE/DP-0020, to provide input for the President's evaluation. The report constituted the Department's input and recommendation to be considered by the President in making his evaluation. Although not required by the Act, the Department made the July 1984 draft of the report available to the general public for review and comment in order to increase public awareness, and develop a public record on the issue of disposal of defense high-level waste. Over 400 copies of the draft report were distributed. Thirty comment letters containing over 400 comments were received from representatives of states, localities, and Indian tribes, federal agencies, organizations representing utilities, public interest groups, individual utilities, and private citizens. All letters were reviewed and considered. Where appropriate, changes were made in the final report reflecting the comments received

Design perspectives for the low and intermediate level radioactive waste repository in Korea

International Nuclear Information System (INIS)

Kim, Young Ki; Koh, Kwang Hoon; Lee, Sang Sun; Lee, Byung Sik; Choi, Gi Won

2007-01-01

The underground waste repository is located at Gyeongju and is designed for the disposal of all the Low- and Intermediate Level Radioactive Waste(LILW). It is scheduled to commence operations in the beginning of 2009. The repository, with a disposal capacity of 800,000 drums, will be constructed in granite rock near the seashore at the Gyeongju site. The repository will be designed to be constructed in phases to reach its final capacity 800,000 drums. In the first phase of construction, the repository will have a capacity to store 100,000 drums. The repository will house all LILW generated in the Republic of Korea. The first phase of the repository design consists of an assess shaft, a construction tunnel, an operating tunnel, an unloading tunnel, and six(6) silos. The silos are located at 80 to 130 meters below Mean Sea level (MSL), in bedrock. Each silo is 24.8m in diameter and 52.4m in height. The silo will be reinforced with concrete lining for rock supports which will also act aas an engineered barrier in limiting radioactive nuclide release aft closure. After serving its intended function the repository will be filled and sealed. The primary objective of filling and sealing is to prevent ground water flow into the silo through the tunnel system and to prevent inadvertent intrusion into the repository after closure

Publishers and repositories

CERN Multimedia

CERN. Geneva

2007-01-01

The impact of self-archiving on journals and publishers is an important topic for all those involved in scholarly communication. There is some evidence that the physics arXiv has had no impact on physics journals, while 'economic common sense' suggests that some impact is inevitable. I shall review recent studies of librarian attitudes towards repositories and journals, and place this in the context of IOP Publishing's experiences with arXiv. I shall offer some possible reasons for the mis-match between these perspectives and then discuss how IOP has linked with arXiv and experimented with OA publishing. As well as launching OA journals we have co-operated with Cornell and the arXiv on Eprintweb.org, a platform that offers new features to repository users. View Andrew Wray's biography

Perceived risk, stigma, and potential economic impacts of a high-level nuclear waste repository in Nevada

International Nuclear Information System (INIS)

Slovic, P.

1989-01-01

This paper addresses the potential for the proposed Yucca Mountain repository to have serious adverse economic impacts on the city of Las Vegas and the State of Nevada. Adverse economic impacts may be expected to result from two related social processes. One has to do with perceptions of risk and socially amplified reactions to unfortunate events associated with the repository (major and minor accidents, discoveries of radiation releases, evidence of mismanagement, attempts to sabotage or disrupt the facility, etc.). The second process that may trigger significant adverse impacts is that of stigmatization. The conceptual underpinnings of risk perception, social amplification, and stigma are discussed in this paper and empirical data are presented to demonstrate how nuclear images associated with Las Vegas and the State of Nevada might trigger adverse effects on tourism, migration, and business development

Deep repository for long-lived low- and intermediate-level waste. Preliminary safety assessment

International Nuclear Information System (INIS)

1999-11-01

A preliminary safety assessment has been performed of a deep repository for long-lived low- and intermediate-level waste, SFL 3-5. The purpose of the study is to investigate the capacity of the facility to act as a barrier to the release of radionuclides and toxic pollutants, and to shed light on the importance of the location of the repository site. A safety assessment (SR 97) of a deep repository for spent fuel has been carried out at the same time. In SR 97, three hypothetical repository sites have been selected for study. These sites exhibit fairly different conditions in terms of hydrogeology, hydrochemistry and ecosystems. To make use of information and data from the SR 97 study, we have assumed that SFL 3-5 is co-sited with the deep repository for spent fuel. A conceivable alternative is to site SFL 3-5 as a completely separate repository. The focus of the SFL 3-5 study is a quantitative analysis of the environmental impact for a reference scenario, while other scenarios are discussed and analyzed in more general terms. Migration in the repository's near- and far-field has been taken into account in the reference scenario. Environmental impact on the three sites has also been calculated. The calculations are based on an updated forecast of the waste to be disposed of in SFL 3-5. The forecast includes radionuclide content, toxic metals and other substances that have a bearing on a safety assessment. The safety assessment shows how important the site is for safety. Two factors stand out as being particularly important: the water flow at the depth in the rock where the repository is built, and the ecosystem in the areas on the ground surface where releases may take place in the future. Another conclusion is that radionuclides that are highly mobile and long-lived, such as 36 Cl and 93 Mo , are important to take into consideration. Their being long-lived means that barriers and the ecosystems must be regarded with a very long time horizon

Environmental impact statements and public consultations on the repository. An outline of SKB's planning

International Nuclear Information System (INIS)

2001-09-01

In December 2000 SKB selected three locations for further investigations as possible sites for the Swedish repository for spent nuclear fuels, Simpevarp at Oskarshamn, Forsmark at Oesthammar and Tierp. Site investigations will be performed during 5-6 years, and will provide data for a site selection. In the application for the repository commission an environmental impact statement should be included, that has been object for consultations with authorities, local communities, other organizations and the public. These consultations will take place during the whole investigation period, and will give ample possibilities for all parties to give their views and to exert an influence on the EIS

Fuzzy distributions in probabilistic environmental impact assessment: application to a high-level waste repository

International Nuclear Information System (INIS)

Datta, D.; Joshi, M.L.

2006-01-01

Environmental modeling with a satisfaction levels of the end user in relation to a defined parameter coupled with imprecision that stems from the field data is a key issue. In the context of this issue success of possibility theory based on fuzzy sets has high visibility in comparison with conventional probability theory. Environmental impact assessments of a high level waste repository is focused using the new approach because the problems under consideration includes a number of qualitative uncertainties at different levels, apart from being quite complex; decision-maker's need to have a transparent assessment result that will enable him to understand underlying assumptions and to judge resulting doses. Fuzzy distributions have been tried to resolve the issues related to the safety of environment from the waste repository. Paper describes the details of fuzzy distribution, fuzzy logic and its possible application to deal the qualitative and quantitative uncertainty in connection with waste repository. (author)

Low- and intermediate-level waste repository-induced effects

Energy Technology Data Exchange (ETDEWEB)

Leupin, O.X.; Marschall, P.; Johnson, L.; Cloet, V.; Schneider, J. [National Cooperative for the Disposal of Radioactive Waste (NAGRA), Wettingen (Switzerland); Smith, P. [Safety Assessment Management Ltd, Henley-On-Thames, Oxfordshire (United Kingdom); Savage, D. [Savage Earth Associates Ltd, Bournemouth, Dorset (United Kingdom); Senger, R. [Intera Inc., Ennetbaden (Switzerland)

2016-10-15

This status report aims at describing and assessing the interactions of the radioactive waste emplaced in a low- and intermediate level waste (L/ILW) repository with the engineered materials and the Opalinus Clay host rock. The Opalinus Clay has a thickness of about 100 m in the proposed siting regions. Among other things the results are used to steer the RD and D programme of NAGRA. The repository-induced effects considered in this report are of the following broad types: - Thermal effects: i.e. effects arising principally from the heat generated by the waste and the setting of cement. - Rock-mechanical effects: i.e. effects arising from the mechanical disturbance to the rock caused by the excavation of the emplacement caverns and other underground structures. - Hydraulic and gas-related effects: i.e. the effects of repository resaturation and of gas generation, e.g. due to the corrosion of metals within the repository, on the host rock and engineered barriers. - Chemical effects: i.e. chemical interactions between the waste, the engineered materials and the host rock. Deep geological repositories are designed to avoid or mitigate the impact of potentially detrimental repository-induced effects on long-term safety. For the repository under consideration in the present report, an assessment of those repository-induced effects that remain shows that detrimental chemical and mechanical impacts are largely confined to the rock adjacent to the excavations, thermal impacts are minimal and gas effects can be mitigated by appropriate design measures to reduce gas production and provide pathways for gas transport that limit gas pressure build-up (engineered gas transport system, or EGTS). Specific measures that are part of the current reference design are discussed in relation to their significance with respect to repository-induced effects. The disposal system described in this report provides a system of passive barriers with multiple safety functions. The disposal

Low- and intermediate-level waste repository-induced effects

International Nuclear Information System (INIS)

Leupin, O.X.; Marschall, P.; Johnson, L.; Cloet, V.; Schneider, J.; Smith, P.; Savage, D.; Senger, R.

2016-10-01

This status report aims at describing and assessing the interactions of the radioactive waste emplaced in a low- and intermediate level waste (L/ILW) repository with the engineered materials and the Opalinus Clay host rock. The Opalinus Clay has a thickness of about 100 m in the proposed siting regions. Among other things the results are used to steer the RD and D programme of NAGRA. The repository-induced effects considered in this report are of the following broad types: - Thermal effects: i.e. effects arising principally from the heat generated by the waste and the setting of cement. - Rock-mechanical effects: i.e. effects arising from the mechanical disturbance to the rock caused by the excavation of the emplacement caverns and other underground structures. - Hydraulic and gas-related effects: i.e. the effects of repository resaturation and of gas generation, e.g. due to the corrosion of metals within the repository, on the host rock and engineered barriers. - Chemical effects: i.e. chemical interactions between the waste, the engineered materials and the host rock. Deep geological repositories are designed to avoid or mitigate the impact of potentially detrimental repository-induced effects on long-term safety. For the repository under consideration in the present report, an assessment of those repository-induced effects that remain shows that detrimental chemical and mechanical impacts are largely confined to the rock adjacent to the excavations, thermal impacts are minimal and gas effects can be mitigated by appropriate design measures to reduce gas production and provide pathways for gas transport that limit gas pressure build-up (engineered gas transport system, or EGTS). Specific measures that are part of the current reference design are discussed in relation to their significance with respect to repository-induced effects. The disposal system described in this report provides a system of passive barriers with multiple safety functions. The disposal

Perceived risk, stigma, and potential economic impacts of a high-level nuclear waste repository in Nevada

International Nuclear Information System (INIS)

Slovic, P.; Layman, M.; Kraus, N.N.; Chalmers, J.; Gesel, G.; Flynn, J.

1989-07-01

This paper describes a program of research designed to assess the potential impacts of a high-level nuclear waste repository at Yucca Mountain, Nevada, upon tourism, retirement and job-related migration, and business development in Las Vegas and the state. Adverse economic impacts may be expected to result from two related social processes. One has to do with perceptions of risk and socially amplified reactions to ''unfortunate events'' associated with the repository (major and minor accidents, discoveries of radiation releases, evidence of mismanagement, attempts to sabotage or disrupt the facility, etc.). The second process that may trigger significant adverse impacts is that of stigmatization. The conceptual underpinnings of risk perception, social amplification, and stigmatization are discussed in this paper and empirical data are presented to demonstrate how nuclear images associated with Las Vegas and the State of Nevada might trigger adverse effects on tourism, migration, and business development

Applying insights from repository safety assessments to evaluating impacts of partitioning and transmutation

International Nuclear Information System (INIS)

Nutt, W. Mark; Swift, Peter N.

2010-01-01

Published analyses of geologic repositories indicate potential for excellent long-term performance for a range of disposal concepts. Estimates of peak dose may be dominated by different radionuclides in different disposal concepts. Thermal loading issues can be addressed by design and operational choices. Impact of waste form lifetime on estimates of peak dose varies for different disposal concepts.

Spent fuel repositories and environmental impact assessment; the legal situation i Finland

International Nuclear Information System (INIS)

Manninen, J.

1995-01-01

The Finnish Act on Environmental Impact Assessment (468/94) builds on the EU Directive 85/337 on the assessment of the effects of certain public and private projects on the environment. The Act is supplemented by the Decree on Environmental Impact Assessment (792/88). The EIA Act is applicable to all nuclear facilities, spent fuel repositories included. In practice the new Act does not introduce any drastic changes to the legal situation, as far as nuclear facilities are concerned. The Finnish Nuclear Energy Act (990/87), which entered into force 1988, already contains most of the basic elements of the environmental impact assessment. In the article, the different steps in the Finnish EIA procedure is described

Repository operational criteria analysis

International Nuclear Information System (INIS)

Hageman, J.P.; Chowdhury, A.H.

1992-08-01

The objective of the ''Repository Operational Criteria (ROC) Feasibility Studies'' (or ROC task) was to conduct comprehensive and integrated analyses of repository design, construction, and operations criteria in 10 CFR Part 60 regulations, considering the interfaces and impacts of any potential changes to those regulations. The study addresses regulatory criteria related to the preclosure aspects of the geologic repository. The study task developed regulatory concepts or potential repository operational criteria (PROC) based on analysis of a repository's safety functions and other regulations for similar facilities. These regulatory concepts or PROC were used as a basis to assess the sufficiency and adequacy of the current criteria in 10 CFR Part 60. Where the regulatory concepts were same as current operational criteria, these criteria were referenced. The operations criteria referenced or the PROC developed are given in this report. Detailed analyses used to develop the regulatory concepts and any necessary PROC for those regulations that may require a minor change are also presented. The results of the ROC task showed a need for further analysis and possible major rule change related to the design bases of a geologic repository operations area, siting, and radiological emergency planning

Projected environmental impacts of radioactive material transportation to the first US repository site

International Nuclear Information System (INIS)

Neuhauser, K.S.; Cashwell, J.W.; Reardon, P.C.; Ostmeyer, R.M.; McNair, G.W.

1986-01-01

This paper discusses the relative national environmental impacts of transporting nuclear wastes to each of the nine candidate repository sites in the United States. Several of the potential sites are closely clustered and, for the purpose of distance and routing calculations, are treated as a single location. These are: Cypress Creek Dome and Richton Dome in Mississippi (Gulf Interior Region), Deaf Smith County and Swisher County sites in Texas (Permian Basin), and Davis Canyon and Lavender Canyon site in Utah (Paradox Basin). The remaining sites are: Vacherie Dome, Louisiana; Yucca Mountain, Nevada; and Hanford Reservation, Washington. For compatibility with both the repository system authorized by the NWPA and with the MRS option, two separate scenarios were analyzed. In belief, they are (1) shipment of spent fuel and high-level wastes (HLW) directly from waste generators to a repository (Reference Case) and (2) shipment of spent fuel to a Monitored Retrievable Storage (MRS) facility and then to a repository. Between 17 and 38 truck accident fatalities, between 1.4 and 7.7 rail accident fatalities, and between 0.22 and 12 radiological health effects can be expected to occur as a result of radioactive material transportation during the 26-year operating period of the first repository. During the same period in the United States, about 65,000 total deaths from truck accidents and about 32,000 total deaths from rail accidents would occur; also an estimated 58,300 cancer fatalities are predicted to occur in the United States during a 26-year period from exposure to background radiation alone (not including medical and other manmade sources). The risks reported here are upper limits and are small by comparison with the ''natural background'' of risks of the same type. 3 refs., 6 tabs

Potential impact of ICRP-30 on the calculated risk from waste repositories

International Nuclear Information System (INIS)

Croff, A.G.

1981-01-01

As a result of the large body of information that has been gathered since ICRP-2 was published (1959), the ICRP has undertaken the task of updating its radiation protection guidance. This update involves revision of the primary radiation guidance as well as the recalculation of intake limits (ICRP-30) based on update biological models, updated nuclide decay schemes, and a new method accounting for simultaneous dose to more than one organ. A detailed analysis of the impacts of ICRP-30 on waste repository safety and risk analyses would require an extensive and detailed study that has not yet been undertaken. Nevertheless, it is possible to identify, in an approximate manner, the impact of using ICRP-30 instead of 10 CFR 20/ICRP-2 in calculating the risk from radioactive repositories. Toward this end, the numerical guidance of ICRP-30 has been obtained and converted into RCG values for the general public using the same methods that were employed in deriving 10 CFR 20. The conversion was cross-checked by comparing 10 CFR 20 and ICRP-30-based values that were known to have remained the same. The most restrictive ICRP-30 RCGs were incorporated into the ORIGEN2 computer code, which was then used to calculate the toxicity of some radioactive materials of interest in waste repository considerations. As a basis for discussion, the toxicities of the spent fuel from a PWR and of the uranium ore required to make the fuel are given for both the 10 CFR 20 and ICRP-30-based RCGs. As is evident, the use of the revised RCGs reduces the toxicity of the spent fuel at times less than 100 years and increases the toxicity at times thereafter

Digital Repositories of Learning Material as a Support Tool for Knowledge Management and Capacity Building

International Nuclear Information System (INIS)

Marmonti, E.

2016-01-01

Full text: For some years, digital repositories are emerging as a de facto standard service for storing, preserving and disseminate knowledge: academic, scientific information and, more recently, primary research data of institutions. Some of the digital repositories host also collections of material classified as learning objects; some others are created to manage only learning objects (LO), as the Learning Objects Digital Repositories, or were built to function as learning objects aggregators. The term “learning object” itself is involving different types of structures, organization and complexity. This paper will show how digital repositories, metadata standards and semantic web technologies can be valuable tools for managing educational content, which can contribute to build a learning and knowledge driven organization. (author

Impact of transporting defense high-level waste to a geologic repository

International Nuclear Information System (INIS)

Joy, D.S.; Shappert, L.B.; Boyle, J.W.

1984-12-01

The Nuclear Waste Policy Act of 1982 (Public Law 97-425) provides for the development of repositories for the disposal of high-level radioactive waste and spent nuclear fuel and requires the Secretary of Energy to evaluate five potential repository sites. One factor that is to be examined is transportation of radioactive materials to such a repository and whether transportation might be affected by shipments to a defense-only repository, or to one that accepts both defense and commercial waste. In response to this requirement, The Department of Energy has undertaken an evaluation of the cost and risk associated with the potential shipments. Two waste-flow scenarios are considered which are related to the total quantity of defense high-level waste which will be placed in a repository. The low-flow case is based on a total of 6700 canisters being transported from one site, while the high-flow case assumes that a total of 20,000 canisters will be transported from three sites. For the scenarios considered, the estimated shipping costs range from $105 million to $257 million depending upon the mode of transport and the repository location. The total risks associated with shipping defense high-level waste to a repository are estimated to be significantly smaller than predicted for other transportation activities. In addition, the cost of shipping defense high-level waste to a repository does not depend on whether the site is a defense-only or a commercial repository. Therefore, the transportation considerations are not a basis for the selection of one of the two disposal options

Impact of advanced fuel cycles on uncertainty associated with geologic repositories

International Nuclear Information System (INIS)

Rechard, Rob P.; Lee, Joon; Sutton, Mark; Greenberg, Harris R.; Robinson, Bruce A.; Nutt, W. Mark

2013-01-01

This paper provides a qualitative evaluation of the impact of advanced fuel cycles, particularly partition and transmutation of actinides, on the uncertainty associated with geologic disposal. Based on the discussion, advanced fuel cycles, will not materially alter (1) the repository performance (2) the spread in dose results around the mean (3) the modeling effort to include significant features, events, and processes in the performance assessment, or (4) the characterization of uncertainty associated with a geologic disposal system in the regulatory environment of the United States. (authors)

Evaluasi Website Repositori Institusi Universitas Surabaya

Directory of Open Access Journals (Sweden)

Amirul Ulum

2015-11-01

Full Text Available The  development  of  institutional  repositories  (IRs  in Indonesia within the broader framework of open access has significant impact on preserving intellectual capital and scholarly communication. Institutional  repositories  play  a  fundamental  role  in  centralizing, preserving,  and  making  accessible  institution’s  intellectual  capital. Evaluation of the system is to determine the functionality the system to meet the users need. Using a descriptive analysis this study wants to evaluate institutional repositories of University of Surabaya. The result is usefull for institution to develop the repository systems.

Deep repository for long-lived low- and intermediate-level waste. Preliminary safety assessment

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-11-01

A preliminary safety assessment has been performed of a deep repository for long-lived low- and intermediate-level waste, SFL 3-5. The purpose of the study is to investigate the capacity of the facility to act as a barrier to the release of radionuclides and toxic pollutants, and to shed light on the importance of the location of the repository site. A safety assessment (SR 97) of a deep repository for spent fuel has been carried out at the same time. In SR 97, three hypothetical repository sites have been selected for study. These sites exhibit fairly different conditions in terms of hydrogeology, hydrochemistry and ecosystems. To make use of information and data from the SR 97 study, we have assumed that SFL 3-5 is co-sited with the deep repository for spent fuel. A conceivable alternative is to site SFL 3-5 as a completely separate repository. The focus of the SFL 3-5 study is a quantitative analysis of the environmental impact for a reference scenario, while other scenarios are discussed and analyzed in more general terms. Migration in the repository's near- and far-field has been taken into account in the reference scenario. Environmental impact on the three sites has also been calculated. The calculations are based on an updated forecast of the waste to be disposed of in SFL 3-5. The forecast includes radionuclide content, toxic metals and other substances that have a bearing on a safety assessment. The safety assessment shows how important the site is for safety. Two factors stand out as being particularly important: the water flow at the depth in the rock where the repository is built, and the ecosystem in the areas on the ground surface where releases may take place in the future. Another conclusion is that radionuclides that are highly mobile and long-lived, such as {sup 36}Cl and {sup 93}Mo , are important to take into consideration. Their being long-lived means that barriers and the ecosystems must be regarded with a very long time horizon.

Multinational/regional repository - an illusion or solution

International Nuclear Information System (INIS)

Mele, I.

2006-01-01

The concept and current status of multinational and regional repositories are presented in the paper. Particular emphasis is given to the results and findings of the recent EU project SAPIERR, investigating the feasibility of regional repository concepts in Europe. Prospects for further development of multinational repositories are also brought forward and the impact and potential benefits of this approach to our national disposal programme are discussed as well. (author)

A Study on Establishment of Buffer Zone of Radioactive Waste Repository

International Nuclear Information System (INIS)

Yoon, Jeong Hyoun; Park, Joo Wan; Ju, Min Su; Kim, Chang Lak; Park, Jin Baek

2008-01-01

A new proposed repository has a final capacity of 800,000 drums radioactive waste. Most of foreign repositories have a general practice of segregating control zones which mainly contributes to classification of degree of control, whether it is called buffer zone or not. Domestic regulatory requirements of establishment of buffer zone in a repository are not much different from those of nuclear power plants for operation period, in which satisfactory design objective or performance objective is the most important factor in determination of the buffer zone. The meaning of buffer zone after closure is a minimum requested area which can prevent inadvertent intruders from leading to non-allowable exposure during institutional control period. Safety assessment with drinking well scenario giving rise to the highest probability of exposure among the intruder's actions can verify fulfillment of the buffer zone which is determined by operational safety of the repository. At present. for the repository to be constructed in a few years, the same procedure and concept as described in this paper are applied that can satisfy regulatory requirements and radiological safety as well. However, the capacity of the repository will be stepwise extended upto 800,000 drums, consequently its layout will be varied too. Timely considerations will be necessary for current boundary of the buffer zone which has been established on the basis of 100,000 drums disposal.

Groundwater impacts of foreseeable human activities on a HLW repository

International Nuclear Information System (INIS)

Coleman, N.M.

1993-01-01

The Nuclear Regulatory Commission (NRC) staff has begun a program of Systematic Regulatory Analysis (SRA) to help ensure that all important technical issues related to the disposal of civilian, high-level nuclear wastes will be identified prior to the receipt of a license application. Large-scale groundwater withdrawals near a repository could have significant impacts on the groundwater flow system. Future large-scale withdrawals of groundwater could occur to support irrigation to growing population centers, such as Las Vegas. Various scenarios of groundwater withdrawals, along with other scenarios of future human activity, will need to be tested before evaluation of the Yucca Mountain site is complete

Reduction of repository heat load using advanced fuel cycles

International Nuclear Information System (INIS)

Preston, Jeff; Miller, L.F.

2008-01-01

With the geologic repository at Yucca Mountain already nearing capacity full before opening, advanced fuel cycles that introduce reprocessing, fast reactors, and temporary storage sites have the potential to allow the repository to support the current reactor fleet and future expansion. An uncertainty analysis methodology that combines Monte Carlo distribution sampling, reactor physics data simulation, and neural network interpolation methods enable investigation into the factor reduction of heat capacity by using the hybrid fuel cycle. Using a Super PRISM fast reactor with a conversion ratio of 0.75, burn ups reach up to 200 MWd/t that decrease the plutonium inventory by about 5 metric tons every 12 years. Using the long burn up allows the footprint of 1 single core loading of FR fuel to have an integral decay heat of about 2.5x10 5 MW*yr over a 1500 year period that replaces the footprint of about 6 full core loadings of LWR fuel for the number of years required to fuel the FR, which have an integral decay heat of about.3 MW*yr for the same time integral. This results in an increase of a factor of 4 in repository support capacity from implementing a single fast reactor in an equilibrium cycle. (authors)

Microbial corrosion of metallic materials in a deep nuclear-waste repository

Directory of Open Access Journals (Sweden)

Stoulil J.

2016-06-01

Full Text Available The study summarises current knowledge on microbial corrosion in a deep nuclear-waste repository. The first part evaluates the general impact of microbial activity on corrosion mechanisms. Especially, the impact of microbial metabolism on the environment and the impact of biofilms on the surface of structure materials were evaluated. The next part focuses on microbial corrosion in a deep nuclear-waste repository. The study aims to suggest the development of the repository environment and in that respect the viability of bacteria, depending on the probable conditions of the environment, such as humidity of bentonite, pressure in compact bentonite, the impact of ionizing radiation, etc. The last part is aimed at possible techniques for microbial corrosion mechanism monitoring in the conditions of a deep repository. Namely, electrochemical and microscopic techniques were discussed.

Draft Environmental Impact Statement for a Geologic Repository for the Disposal of Spent Nuclear Fuel and High-Level Radioactive Waste at Yucca Mountain, Nye County, Nevada

International Nuclear Information System (INIS)

1999-01-01

The Proposed Action addressed in this EIS is to construct, operate and monitor, and eventually close a geologic repository at Yucca Mountain in southern Nevada for the disposal of spent nuclear fuel and high-level radioactive waste currently in storage at 72 commercial and 5 DOE sites across the United States. The EIS evaluates (1) projected impacts on the Yucca Mountain environment of the construction, operation and monitoring, and eventual closure of the geologic repository; (2) the potential long-term impacts of repository disposal of spent nuclear fuel and high-level radioactive waste; (3) the potential impacts of transporting these materials nationally and in the State of Nevada; and (4) the potential impacts of not proceeding with the Proposed Action

Risk-induced social impacts: The effects of the proposed nuclear waste repository on residents of the Las Vegas metropolitan area

International Nuclear Information System (INIS)

Mushkatel, A.H.; Pijawka, K.D.; Dantico, M.

1990-09-01

This report examines important and major impacts of the proposed high-level nuclear waste repository on Las Vegas metropolitan residents. The data utilized in the report consist of interview data collected in the 1988, Urban Risk Survey and data for Clark County residents collected as part of the 1989 Nevada Telephone Survey. The use of two different data sets which were collected at two distinct points in time permit for not only determinations of the consistency of opinions and risk perceptions, but also result in a compelling consistency of findings demonstrating the types of impacts described in the report. The repository is viewed as an extremely dangerous facility where accidents are perceived as inevitable, and the consequences may result in catastrophic impacts. Over the last few years, the negative imagery of the repository, coupled with the view that the area may become stigmatized has amplified the perceived risks over the benefits. In addition, Las Vegas valley residents have little trust in the agencies empowered to ensure their safety and to mitigate the impacts from the facility. In this context it is difficult to believe that the federal agencies can regain much credibility among Clark County residents, or that the major impacts outlined in the report if the Yucca Mountain project becomes a reality will not come about. 20 refs., 3 figs., 36 tabs

High-level waste repository-induced effects

Energy Technology Data Exchange (ETDEWEB)

Leupin, O.X.; Marschall, P.; Johnson, L.; Cloet, V.; Schneider, J. [National Cooperative for the Disposal of Radioactive Waste (NAGRA), Wettingen (Switzerland); Smith, P. [Safety Assessment Management Ltd, Henley-On-Thames, Oxfordshire (United Kingdom); Savage, D. [Savage Earth Associates Ltd, Bournemouth, Dorset (United Kingdom); Senger, R. [Intera Inc., Ennetbaden (Switzerland)

2016-10-15

by restricting the size of the excavations and the depth of the repository, using a low-deformation, controlled construction and excavation method and by the fact that the excavations will be backfilled relatively soon after construction with a swelling backfill material. At expected repository depths, the rooms will need to be supported to ensure stability and worker protection; this will prevent rock falls and further extension of the EDZ. Based on the modelling results, it can be concluded that the extent of the EDZ around the HLW emplacement rooms will not exceed a thickness of one room diameter and that the average hydraulic conductance of the EDZ around emplacement rooms, access tunnels and shafts will not exceed a value of 10{sup -7} m{sup 3}/s. Self-sealing of the EDZ and low hydraulic gradients along the tunnels will result in negligible radionuclide transport by the EDZ pathway. The relevant chemical interactions are taken into account when designing and assessing the performance of a HLW repository. In the current reference design, tunnel support is provided by a concrete liner. It is expected that degradation of the liner and corrosion of the steel canister and other supporting structures will lead to some alteration of the bentonite buffer and Opalinus Clay. These detrimental effects are taken into account in dose calculations and have been found not to have a significant impact on the calculated dose rates. For the reference gas generation rates, the gas transport capacity of the Opalinus Clay is sufficiently high to dispel gas without invoking pathway dilation as a gas transport mechanism and without causing damage to the rock. Even if potential transport pathways for gas along the excavations and EDZ are disregarded, overpressures that would lead to the onset of pathway dilation are reached only in cases combining conservative gas generation rates with a low-permeability host rock, and these overpressures are still insufficient to cause rock damage

High-level waste repository-induced effects

International Nuclear Information System (INIS)

Leupin, O.X.; Marschall, P.; Johnson, L.; Cloet, V.; Schneider, J.; Smith, P.; Savage, D.; Senger, R.

2016-10-01

by restricting the size of the excavations and the depth of the repository, using a low-deformation, controlled construction and excavation method and by the fact that the excavations will be backfilled relatively soon after construction with a swelling backfill material. At expected repository depths, the rooms will need to be supported to ensure stability and worker protection; this will prevent rock falls and further extension of the EDZ. Based on the modelling results, it can be concluded that the extent of the EDZ around the HLW emplacement rooms will not exceed a thickness of one room diameter and that the average hydraulic conductance of the EDZ around emplacement rooms, access tunnels and shafts will not exceed a value of 10 -7 m 3 /s. Self-sealing of the EDZ and low hydraulic gradients along the tunnels will result in negligible radionuclide transport by the EDZ pathway. The relevant chemical interactions are taken into account when designing and assessing the performance of a HLW repository. In the current reference design, tunnel support is provided by a concrete liner. It is expected that degradation of the liner and corrosion of the steel canister and other supporting structures will lead to some alteration of the bentonite buffer and Opalinus Clay. These detrimental effects are taken into account in dose calculations and have been found not to have a significant impact on the calculated dose rates. For the reference gas generation rates, the gas transport capacity of the Opalinus Clay is sufficiently high to dispel gas without invoking pathway dilation as a gas transport mechanism and without causing damage to the rock. Even if potential transport pathways for gas along the excavations and EDZ are disregarded, overpressures that would lead to the onset of pathway dilation are reached only in cases combining conservative gas generation rates with a low-permeability host rock, and these overpressures are still insufficient to cause rock damage. It is

Heat Capacity Analysis Report

International Nuclear Information System (INIS)

Findikakis, A.

2004-01-01

The purpose of this report is to provide heat capacity values for the host and surrounding rock layers for the waste repository at Yucca Mountain. The heat capacity representations provided by this analysis are used in unsaturated zone (UZ) flow, transport, and coupled processes numerical modeling activities, and in thermal analyses as part of the design of the repository to support the license application. Among the reports that use the heat capacity values estimated in this report are the ''Multiscale Thermohydrologic Model'' report, the ''Drift Degradation Analysis'' report, the ''Ventilation Model and Analysis Report, the Igneous Intrusion Impacts on Waste Packages and Waste Forms'' report, the ''Dike/Drift Interactions report, the Drift-Scale Coupled Processes (DST and TH Seepage) Models'' report, and the ''In-Drift Natural Convection and Condensation'' report. The specific objective of this study is to determine the rock-grain and rock-mass heat capacities for the geologic stratigraphy identified in the ''Mineralogic Model (MM3.0) Report'' (BSC 2004 [DIRS 170031], Table 1-1). This report provides estimates of the heat capacity for all stratigraphic layers except the Paleozoic, for which the mineralogic abundance data required to estimate the heat capacity are not available. The temperature range of interest in this analysis is 25 C to 325 C. This interval is broken into three separate temperature sub-intervals: 25 C to 95 C, 95 C to 114 C, and 114 C to 325 C, which correspond to the preboiling, trans-boiling, and postboiling regimes. Heat capacity is defined as the amount of energy required to raise the temperature of a unit mass of material by one degree (Nimick and Connolly 1991 [DIRS 100690], p. 5). The rock-grain heat capacity is defined as the heat capacity of the rock solids (minerals), and does not include the effect of water that exists in the rock pores. By comparison, the rock-mass heat capacity considers the heat capacity of both solids and pore

Logistics characterization for regional spent fuel repositories concept

International Nuclear Information System (INIS)

Joy, D.S.; Hudson, B.J.; Anthony, M.W.

1980-08-01

This report summarizes a study of logistics considerations for a four-region repository system for spent fuel disposal. The logistics considerations include: (1) yearly receipt and emplacement; (2) inventory; (3) away-from-reactor (AFR) storage; (4) nuclear capacity growth effects; (5) entire lifetime of reactors served by repository operations; (6) proportions of pressurized-water-reactor (PWR)/boiling-water-reactor (BWR) fuel; (7) proportions of rail and truck shipments; (8) shipping cask fleet requirements; (9) number of annual shipments; (10) mode (rail/truck) and cost of shipment; and (11) initial year for shipment to maintain full core reserve. The nation was divided into Northeast, North Central, Southern, and Western regions for evaluation purposes. Repository logistics were analyzed in each region based on three different capacity projections. For the Southern region, results for seven salt dome sites are presented. The Western region results cover four potential sites. The North Central and Northeastern regions results are not presented on a site specific basis. Conclusions are drawn based on the results. The methodology assumptions and references used in the logistics analysis are described for the convenience of the reader

Evaluating total carrying capacity of tourism using impact indicators

Directory of Open Access Journals (Sweden)

R. Sharma

2016-03-01

Full Text Available The carrying capacity is well identified tool to manage problems due to uncontrolled tourism for any destination. This report highlights the carrying capacity estimation of Kerwa tourism area, Bhopal, India. The methodology used in this report is a new two-tier mechanism of impact analysis using index numbers derived from a survey of 123 stakeholders. From this the individual component impact analysis and the total carrying capacity of the area is computed in order to state the insight of the total carrying capacity left for the tourism activities in Kerwa tourism area. It is calculated from, the results so obtained, that the Kerwa catchment area falls in “very low impact category” and hence in a healthy state of the artwork in terms of total carrying capacity. The study conveys the current need in the destination management and tourism development as a road map for the destination managers for implementing sustainable tourism.

Repository operational criteria comparative analysis

International Nuclear Information System (INIS)

Hageman, J.P.; Chowdhury, A.H.

1994-06-01

The objective of the ''Repository Operational Criteria (ROC) Feasibility Studies'' (or ROC task) was to conduct comprehensive and integrated analyses of repository design, construction, and operations criteria in 10 CFR Part 60 regulations considering the interfaces among the components of the regulations and impacts of any potential changes to those regulations. The ROC task addresses regulatory criteria and uncertainties related to the preclosure aspects of the geologic repository. Those parts of 10 CFR Part 60 that require routine guidance or minor changes to the rule were addressed in Hageman and Chowdhury, 1992. The ROC task shows a possible need for further regulatory clarity, by major changes to the rule, related to the design bases and siting of a geologic repository operations area and radiological emergency planning in order to assure defense-in-depth. The analyses, presented in this report, resulted in the development and refinement of regulatory concepts and their supporting rationale for recommendations for potential major changes to 10 CFR Pan 0 regulations

Investigating the sealing capacity of a seal system in rock salt (DOPAS project)

Energy Technology Data Exchange (ETDEWEB)

Jantschik, Kyra; Moog, Helge C.; Czaikowski, Oliver; Wieczorek, Klaus [Gesellschaft fuer Anlagen- und Reaktorsicherheit (GRS) gGmbH, Braunschweig (Germany)

2016-11-15

This paper describes research and development work on plugging and sealing repositories, an issue of fundamental importance for the rock salt option which represents one of the three European repository options, besides the clay rock and the crystalline rock options. The programme aims at providing experimental data needed for the theoretical analysis of the long-term sealing capacity of concrete- based sealing materials. In order to demonstrate hydro-mechanical material stability under representative load scenarios, a comprehensive laboratory testing programme is carried out. This comprises investigation of the sealing capacity of the combined seal system and impact of the so-called excavation-damaged zones (EDZ) as well as investigation of the hydro-chemical long-term stability of the seal in contact with different brines under diffusive and advective conditions. This paper presents experimental approaches and preliminary results from laboratory investigations on salt concrete and combined systems as obtained to date.

Fuel cycle covariance of plutonium and americium separations to repository capacity using information theoretic measures

International Nuclear Information System (INIS)

Scopatz, Anthony; Schneider, Erich; Li, Jun; Yim, Man-Sung

2011-01-01

A light water reactor, fast reactor symbiotic fuel cycle scenario was modeled and parameterized based on thirty independent inputs. Simultaneously and stochastically choosing different values for each of these inputs and performing the associated fuel cycle mass-balance calculation, the fuel cycle itself underwent Monte Carlo simulation. A novel information theoretic metric is postulated as a measure of system-wide covariance. This metric is the coefficient of variation of the set of uncertainty coefficients generated from 2D slices of a 3D contingency table. It is then applied to the fuel cycle, taking fast reactor used fuel plutonium and americium separations as independent variables and the capacity of a fully-loaded tuff repository as the response. This set of parameters is known from prior studies to have a strong covariance. When measured with all 435 other input parameters possible, the fast reactor plutonium and americium separations pair was found to be ranked the second most covariant. This verifies that the coefficient of variation metric captures the desired sensitivity of sensitivity effects in the nuclear fuel cycle. (author)

Executive-style briefings on selected repository design issues

International Nuclear Information System (INIS)

1978-01-01

This document is a collection of executive-style briefings on selected repository design issues. Most of the briefings discuss differences between the US repository design bases presented in US Working Draft on Repository Physical Descriptions in a Salt Formation, prepared in support of INFCE discussions of May 1978 and the FRG-Netherlands design bases, presented in Design Study of a Radioactive Waste Repository to be Mined in a Medium-Size Salt Dome by Hamstra and Velzeboer, Netherlands Energy Research Foundation, January 1978. Advantages and disadvantages of the two sets of design bases are discussed, and the impacts of adopting either of these bases on the other's programs and positions are identified

Digital Repositories An investigation of best practices for content recruitment to academic digital repositories and the conditions for their livelihood

CERN Document Server

Hagen, Reidun Anette

2009-01-01

A digital repository is a web accessible database, aimed at preserving the research material of an institution or scientific community. A digital repository serves as a tool for dissemination of research material and can increase the impact of the research by making it freely accessible. Digital repositories are often mentioned as a possible aid in relation to the Open Access debate; how research material should be freely accessible to anyone, anywhere at any time. However, for a digital repository to fully unleash its potential as a crucial component of Open Access, it is reliant on the ability to successfully collect and organize content. To a large extent this involves initiating self-archiving of research material by scientists throughout the academic world. This is not a trivial task, and many current repositories are inadequate in this respect, remaining empty, unvisited shelves. This thesis explores best practices for content recruitment to digital repositories, through the review of literature, and an...

An assessment of the radiological impact of coastal erosion of the UK Low-Level Waste Repository - 59137

International Nuclear Information System (INIS)

Sumerling, Trevor; Shevelan, John; Cummings, Richard; Fish, Paul; Towler, George; Penfold, James

2012-01-01

The UK Low Level Waste Repository Ltd submitted an Environmental Safety Case for the disposal of low-level waste to our regulator, the Environment Agency, on the 1 May 2011. This includes assessments of the long-term radiological safety of past and future disposals. A particular feature of the Low Level Waste Repository (LLWR) is that, because of its proximity to the coast, the site is vulnerable to coastal erosion. Our present understanding is that the site will be eroded on a timescale of a few hundred to a few thousand years, with consequent disruption of the repository, and dispersal of the wastes. We have undertaken a programme of scientific research and monitoring to characterise the evolution and function of the current coastal system that provides a basis for forecasting its future evolution. This has included modelling of contemporary hydrodynamics, geo-morphological mapping, repeat LiDAR and aerial photographic surveys to detect patterns and rates of change, coastal inspections and reconstructions of post-glacial (i.e. last 15, 000 years) sea levels and sediment budgets. Estimates of future sea-level rise have been derived from international sources and consideration given to the impact of such on the local coastline. Two alternative models of coastal recession have then been applied, one empirical and one physical-process based, taking account of the composition of Quaternary-age sediments between the coast and the site and uncertainties in future local sea level change. Comparison of the ranges of calculated times to site contact with sea-level rise indicate that the repository is most likely to be disrupted by undercutting of the engineered vaults and of the trenches. A novel and flexible radiological assessment model has been developed to analyse the impacts of the erosion of the repository and subsequent dispersal of wastes. The model represents the spatial layout of the site and distribution of radionuclides within the repository and is able to take

Social impacts of hazardous and nuclear facilities and events: Implications for Nevada and the Yucca Mountain high-level nuclear waste repository

International Nuclear Information System (INIS)

Freudenburg, W.R.; Carter, L.F.; Willard, W.; Lodwick, D.G.; Hardert, R.A.; Levine, A.G.; Couch, S.R.; Edelstein, M.R.

1992-05-01

Social impacts of a nuclear waste repository are described. Various case studies are cited such as Rocky Flats Plant, the Feed Materials Production Center, and Love Canal. The social impacts of toxic contamination, mitigating environmental stigma and loss of trust are also discussed

Prestudy Oskarshamn. Tourism in Oskarshamn with or without a repository

International Nuclear Information System (INIS)

Nordblom, C.J.; Foghagen, C.

1998-11-01

Consequences for the tourism at Oskarshamn from siting a spent fuel repository in the community are studied. Four questionnaire/interview enquires were performed, and the analysis of the results show that no noticeable effects are expected. Still, an uncertainty about the impact of a repository is felt by the public, and more thorough information about the repository and its components is needed

Impact of MDGs capacity building workshop on teachers ...

African Journals Online (AJOL)

To address the issue, Millennium Development Goals (MDGs) sponsored capacity building workshops for primary school teachers. The paper explores the impact of this capacity building workshop on teachers' level of competence and pupils' performance. Sixty teachers were selected purposively for the study and 418 ...

Bearing Capacity of Foundations subjected to Impact Loads

DEFF Research Database (Denmark)

Ibsen, Lars Bo; Jakobsen, Kim Parsberg

1996-01-01

In the design process for foundations, the bearing capacity calculations are normally restricted to monotonic loads. Even in cases where the impact load is of significance the dynamic aspects are neglected by use of a traditional deterministic ultimate limit state analysis. Nevertheless it is com......In the design process for foundations, the bearing capacity calculations are normally restricted to monotonic loads. Even in cases where the impact load is of significance the dynamic aspects are neglected by use of a traditional deterministic ultimate limit state analysis. Nevertheless...

Report on the evaluation under the Act No 24/2006 of Coll. Environmental Impact Assessment Law Extension of National Radioactive Waste Repository in Mochovce for disposal low-level radioactive waste and construction of very low-level radioactive waste repository

International Nuclear Information System (INIS)

Hanusik, V.; Moravek, J.; Kusovska, Z.

2011-01-01

The report elaborated assessment of the environmental impact of extension of the National Radioactive Waste Repository in Mochovce for disposal of low and intermediate level radioactive wastes. Within this repository also the premises for very low level radioactive waste deposition should be built. The assessment report was prepared according to the Act no. 24/2006 Coll, as amended 'On the assessment of environmental impacts' Annex No. 11 upon The scope of assessment issued by the competent authority on the basis of assessment of Intent for this action. The report was prepared in VUJE, Inc. Trnava for Nuclear and Decommissioning Company, Inc. Bratislava (JAVYS).

Upgrading of radon's type near surface repository in Latvia

International Nuclear Information System (INIS)

Abramenkovs, A.

2006-01-01

In 1959, the Soviet government decided to construct the near surface radioactive wastes repository 'Radons' near the Baldone city. It was put in operation in 1962. The changes in the development of the repository were induced by the necessarily to upgrade it for disposal of radioactive wastes from the decommissioning of the Salaspils Research Reactor (SRR). The safety assessment of repository was performed during 2000-2001 under the PHARE project for necessary upgrades of repository. The outline design for new vaults and interim storage for long lived radioactive wastes was elaborated during 2003-2004 years. The Environmental Impact Assessment (EIA) for upgrade of Baldone repository was performed during 2004-2005 years. It was found, that additional efforts must be devoted for solution of social aspects o for successful operation and upgrade of repository. It was shown by EIA, that the local population has a negative opinion against the upgrade of repository in Latvia. The main recommendations for upgrades were connected with increasing the safety of repository, increasing of PR activities for education of society and developing of compensation mechanism for local municipality. (author)

The role of weapons production and military waste in the repository selection process

International Nuclear Information System (INIS)

Nelson, D.; Hope, J.; Power, W.; Hunter, T.

1987-01-01

The decision to commingle defense waste with commercial waste in the nuclear waste repository program has many impacts on that program. There will be more waste to place in the two repositories authorized under the Nuclear Waste Policy Act, more transport miles to get the waste to a repository, and more costs associated with environmental and socio-economic impact mitigation. This paper explores the links between weapons production and military waste, and the repository selection process. The paper first describes the importance of state, tribe and public participation to the acceptance of a repository site selection. The paper then examines the various estimates of amounts of existing and future military nuclear wastes, and how these estimates affect repository siting decisions. The final section addresses the public policy questions which surround this issue. Repository siting may be jeopardized unless there is open public discussion about existing radioactive contamination at military production sites and about future nuclear weapons production. Cost-sharing is considered within this context

Capacity assessment of concrete containment vessels subjected to aircraft impact

Energy Technology Data Exchange (ETDEWEB)

Andonov, Anton, E-mail: anton.andonov@mottmac.com; Kostov, Marin; Iliev, Alexander

2015-12-15

Highlights: • An approach to assess the containment capacity to aircraft impact via fragility curves is proposed. • Momentum over Area was defined as most suitable reference parameter to describe the aircraft load. • The effect of the impact induced damages on the containment pressure capacity has been studied. • The studied containment shows no reduction of the pressure capacity for the investigated scenarios. • The effectiveness of innovative protective structure against aircraft impact has been evaluated. - Abstract: The paper describes the procedure and the results from the assessment of the vulnerability of a generic pre-stressed containment structure subjected to a large commercial aircraft impact. Impacts of Boeing 737, Boeing 767 and Boeing 747 have been considered. The containment vulnerability is expressed by fragility curves based on the results of a number of nonlinear dynamic analyses. Three reference parameters have been considered as impact intensity measure in the fragility curve definition: peak impact force (PIF), peak impact pressure (PIP) and Momentum over Area (MoA). Conclusions on the most suitable reference parameter as well on the vulnerability of such containment vessels are drawn. The influence of the aircraft impact induced damages on the containment ultimate pressure capacity is also assessed and some preliminary conclusions on this are drawn. The paper also addresses a conceptual design of a protective structure able to decrease the containment vulnerability and provide a preliminary assessment of the applicability of such concept.

Capacity assessment of concrete containment vessels subjected to aircraft impact

International Nuclear Information System (INIS)

Andonov, Anton; Kostov, Marin; Iliev, Alexander

2015-01-01

Highlights: • An approach to assess the containment capacity to aircraft impact via fragility curves is proposed. • Momentum over Area was defined as most suitable reference parameter to describe the aircraft load. • The effect of the impact induced damages on the containment pressure capacity has been studied. • The studied containment shows no reduction of the pressure capacity for the investigated scenarios. • The effectiveness of innovative protective structure against aircraft impact has been evaluated. - Abstract: The paper describes the procedure and the results from the assessment of the vulnerability of a generic pre-stressed containment structure subjected to a large commercial aircraft impact. Impacts of Boeing 737, Boeing 767 and Boeing 747 have been considered. The containment vulnerability is expressed by fragility curves based on the results of a number of nonlinear dynamic analyses. Three reference parameters have been considered as impact intensity measure in the fragility curve definition: peak impact force (PIF), peak impact pressure (PIP) and Momentum over Area (MoA). Conclusions on the most suitable reference parameter as well on the vulnerability of such containment vessels are drawn. The influence of the aircraft impact induced damages on the containment ultimate pressure capacity is also assessed and some preliminary conclusions on this are drawn. The paper also addresses a conceptual design of a protective structure able to decrease the containment vulnerability and provide a preliminary assessment of the applicability of such concept.

Evaluation of radionuclide migration in the homogeneous system of a geological repository

International Nuclear Information System (INIS)

Prvakova, S.; Duran, J.; Necas, V.

2005-01-01

The aim of this paper is to study radionuclide migration and release from a deep underground repository situated in a clay formation. An insight into the processes influencing the radionuclide transport in the near field and far field will be presented. For the calculation, a set of radionuclides has been chosen, considering the half-life, decay chains, capacity of the sorption, solubility limits and diffusion coefficients. The migration of radionuclides is dependent on transport properties of the particular nuclide. Due to the low hydraulic conductivity of the backfill material and clay geological formation, the transport in the repository occurs mainly by diffusion. The migration rate will be influenced by the water chemistry, solubility, retardation and diffusive properties of the nuclides, and the water flow rate in the clay. The release rates of radionuclides from the geosphere to the biosphere will be converted into the indicative dose rates using dose conversion factors for ingestion. The impact of the critical group is considered via consumption of meat, root vegetables and drinking water from wells. (author)

Availability and Accessibility in an Open Access Institutional Repository: A Case Study

Science.gov (United States)

Lee, Jongwook; Burnett, Gary; Vandegrift, Micah; Baeg, Jung Hoon; Morris, Richard

2015-01-01

Introduction: This study explores the extent to which an institutional repository makes papers available and accessible on the open Web by using 170 journal articles housed in DigiNole Commons, the institutional repository at Florida State University. Method: To analyse the repository's impact on availability and accessibility, we conducted…

VerSi. A method for the quantitative comparison of repository systems

Energy Technology Data Exchange (ETDEWEB)

Kaempfer, T.U.; Ruebel, A.; Resele, G. [AF-Consult Switzerland Ltd, Baden (Switzerland); Moenig, J. [GRS Braunschweig (Germany)

2015-07-01

Decision making and design processes for radioactive waste repositories are guided by safety goals that need to be achieved. In this context, the comparison of different disposal concepts can provide relevant support to better understand the performance of the repository systems. Such a task requires a method for a traceable comparison that is as objective as possible. We present a versatile method that allows for the comparison of different disposal concepts in potentially different host rocks. The condition for the method to work is that the repository systems are defined to a comparable level including designed repository structures, disposal concepts, and engineered and geological barriers which are all based on site-specific safety requirements. The method is primarily based on quantitative analyses and probabilistic model calculations regarding the long-term safety of the repository systems under consideration. The crucial evaluation criteria for the comparison are statistical key figures of indicators that characterize the radiotoxicity flux out of the so called containment-providing rock zone (einschlusswirksamer Gebirgsbereich). The key figures account for existing uncertainties with respect to the actual site properties, the safety relevant processes, and the potential future impact of external processes on the repository system, i.e., they include scenario-, process-, and parameter-uncertainties. The method (1) leads to an evaluation of the retention and containment capacity of the repository systems and its robustness with respect to existing uncertainties as well as to potential external influences; (2) specifies the procedures for the system analyses and the calculation of the statistical key figures as well as for the comparative interpretation of the key figures; and (3) also gives recommendations and sets benchmarks for the comparative assessment of the repository systems under consideration based on the key figures and additional qualitative

Selection of nuclide decay chains for use in the assessment of the radiological impact of geological repositories for radioactive waste

International Nuclear Information System (INIS)

Thorne, M.C.

1982-12-01

The criteria for selecting nuclide decay chains for use in the assessment of the radiological impact of geological repositories for radioactive waste are given. The reduced chains recommended for use with SYVAC are described. (author)

Estimating the economic impact of a repository from scenario-based surveys: Models of the relation of stated intent to actual behavior

International Nuclear Information System (INIS)

Easterling, D.; Morwitz, V.; Kunreuther, H.

1990-12-01

The task of estimating the economic impact of a facility as novel and long-lived as a high-level nuclear waste (HLNW) repository is fraught with uncertainty. One approach to the forecasting problems is to survey economic agents as to how they would respond when confronted with hypothetical repository scenarios. A series of such studies conducted for the state of Nevada have examined the potential impact of a Yucca Mountain repository on behavior such as planning conventions, attending conventions, vacationing, outmigration, immigration, and business location. In each case, respondents drawn from a target population report on whether a particular repository event (either some form of an accident, or simply the presence of the facility) would cause them to act any differently than they otherwise would. The responses to such a survey provide an indication of whether or not economic behavior would be altered. However, the analysis is inevitably plagued with the question of how much credence to place in the reports of intended behavior; can we believe what people report they would do in a hypothetical situation? The present study examines a more precise version of this question regarding the validity of stated intent data. After reviewing a variety of literature in the area of intent versus actual behavior, we provide an answer to the question, ''What levels of actual behavior are consistent with the intent data that have been observed in the repository surveys?'' More formally, we assume that we are generally interested in predicting the proportion of a sample who will actually perform a target behavior. 86 refs., 6 figs., 9 tabs

Impact assessment of the impact on nature values of the construction and operation of the repository for spent nuclear fuel at Forsmark; Konsekvensbedoemning av paaverkan paa naturvaerden av anlaeggande och drift av slutfoervar foer anvaent kaernbraensle i Forsmark

Energy Technology Data Exchange (ETDEWEB)

Allmer, Johan (Ekologigruppen AB, Stockholm (Sweden))

2011-03-15

Construction and operation of a repository at Soederviken in Forsmark, Oesthammar municipality means impact, effects and consequences for the environment. This report describes the natural conditions and natural values in Forsmark with particular focus on Soederviken. Furthermore, an assessment of consequences for the natural environment in the development and operation of a repository at Soederviken. Assessment of impacts from water activities are treated in a special report.

The effect of microorganisms on asphaltopropylene concrete in a radioactive waste repository. Part 2

International Nuclear Information System (INIS)

Hlavackova, I.; Hlavacek, I.; Mara, M.; Wasserbauer, R.

1993-11-01

The permeability of asphaltopropylene concrete (APC) was examined after the action of aerobic bacteria and molds, and the changes in its volume, weight and swelling capacity were recorded. APC has been used as a sealing material in low level radioactive waste pits at the Dukovany NPP repository. Results of check-up sampling of microorganisms in the repository are evaluated. Sulphate reducing bacteria, which have been detected in soil near the reactor site, were isolated and their action upon asphaltopropylene (AP) was investigated. The resistance of bitumen layers containing model waste, against the action of aerobic bacteria and molds and against water was also examined. Bitumen samples containing model waste were found to absorb water at low temperatures considerably faster than unfilled bitumen. At elevated temperatures the absorption of water is appreciable, causing high weight losses of the bituminized waste layer due to degradation. The time dependences of the bitumen sample weight at 20 degC and 60 degC in distilled and cement water are given in the Appendix. The results included in the final reports ''Investigation of the effect of microorganisms on asphaltopropylene-based insulating materials employed as sealing in the secondary radioactive waste repository at the Dukovany NPP in relation to the microbial flora present. Bacteria'' and ''Investigation of the impact of biodegradation effects of aerobic and anaerobic microorganisms including molds on asphalt and asphaltopropylene in conditions of the ground repository at the Dukovany NPP'' are also given. (J.B.). 8 tabs., 33 figs

Barriers to migration of radionuclides from radioactive waste repositories

International Nuclear Information System (INIS)

Stefanova, I.

1999-01-01

Natural inorganic sorbents are known as effective barriers that reduce the migration of radionuclides from radioactive waste repositories and contaminated sites. They could be used as buffer, backfill and sealing materials in the repository and their presence in the host rock and the surrounding geological formations increases the retention properties of the strata. Natural occurring minerals from local origin are used in the study - zeolites (clinoptilolite and mordenite), celadonite and loess. Sorption of wide range of radionuclides is studies. Batch capacity is determined. Sorption of radionuclides from simulated natural solution is studied. Distribution coefficients are calculated from sorption isotherms. Desorption in presence of different natural solutions is studied. Sorption properties are compared. It is shown that clinoptilolite acts as effective barrier against migration of radionuclides from repositories. The presence of celadonite in the clinoptilolite rock increases the retention of polyvalent ions. The retention of radionuclides on loess samples fulfils the requirements for host media for repository for low and intermediate level waste. A method for construction of additional barrier to the existing in the country disposal vault for spent sealed sources is proposed

Deep repository and encapsulation plant for spent nuclear fuel. Consultation and environmental impact assessment according to the Environmental Code and the Nuclear Activities Act

International Nuclear Information System (INIS)

2002-11-01

As a part of its programme for siting of a deep repository for spent nuclear fuel, SKB has recently commenced site investigations at Forsmark in Oesthammar Municipality and at Simpevarp in Oskarshamn Municipality. At the same time, SKB has initiated the consultation process prior to application for permits/licences under the Environmental Code and the Nuclear Activities Act. Early consultation has been carried out for both sites, and a consultation report has been submitted to the county administrative boards in Kalmar County and Uppsala County for decisions regarding significant environmental impact. After decisions by the county administrative boards, SKB will commence the work with environmental impact assessment and extended consultation. SKB's main alternative for the encapsulation plant is siting adjacent to CLAB. In the spring of 2003, SKB will convene early consultation on the encapsulation plant. This will be followed by extended consultation up to 2005. This process will be coordinated with the extended consultation for a deep repository in Oskarshamn. An alternative is to locate the encapsulation plant at a deep repository at Forsmark. This alternative is being dealt with completely within the extended consultation for the deep repository at Forsmark. Three different permits/licences are required for both the encapsulation plant and the deep repository: a permit under the Environmental Code, a licence under the Nuclear Activities Act, and a building permit under the Planning and Building Act. Licensing under the Environmental Code and the Nuclear Activities Act takes place in parallel. The applications under both laws must include an environmental impact statement (EIS) prepared according to the rules in Chapter 6 of the Environmental Code. The same EIS is thus used in both applications. Separate EISs are prepared for the encapsulation plant and the deep repository. According to the Environmental Code, the consultation shall relate to the location, scope

Protocol for characterization of clay as a backfill and coverage layers for surface repository

International Nuclear Information System (INIS)

Santos, Daisy M.M.; Tello, Clédola C.O.

2017-01-01

The Radioactive Waste Management includes the operations since generation of the waste until its storage in repository, ensuring the protection of human beings and the environment from the possible negative impacts. The radioactive waste is segregated, treated, conditioned in suitable packages for posterior storage or disposal in repository. The 'RBMN Project' objective is to implement the repository for the disposal of low and intermediate level radioactive wastes generated by nuclear activities in Brazil, proposing a definitive solution for their storage. Engineered and natural barriers as the backfill and coverage layers will compose the disposal system of a near surface repository, concept proposed by the 'RBMN Project'. The use of these barriers aims to avoid or restrict the release of radionuclides from the waste to the human beings and environment. The waterproofing barriers are composed of clays. Certainly, for the national repository, will be used those clays existing in the place where it will be constructed. Them some basic tests will have to be carried out to verify the suitability of these clays as barriers. These tests were determined and performed with reference clay, a Brazilian bentonite constituted of 67.2% montmorillonite. The results were compared with national and international literature of materials with similar mineralogical features. The values found with 95% of confidence interval were 9.73±0,35 μm for granulometric size; 13,3±0,6% for the moisture content and 816±9 mmol.kg -1 for the capacity of cationic exchange. A protocol for characterization of clay was elaborated presenting these tests for it future use. (author)

Protocol for characterization of clay as a backfill and coverage layers for surface repository

Energy Technology Data Exchange (ETDEWEB)

Santos, Daisy M.M.; Tello, Clédola C.O., E-mail: marymarchezini@gmail.com, E-mail: tellocc@cdtn.br [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil)

2017-07-01

The Radioactive Waste Management includes the operations since generation of the waste until its storage in repository, ensuring the protection of human beings and the environment from the possible negative impacts. The radioactive waste is segregated, treated, conditioned in suitable packages for posterior storage or disposal in repository. The 'RBMN Project' objective is to implement the repository for the disposal of low and intermediate level radioactive wastes generated by nuclear activities in Brazil, proposing a definitive solution for their storage. Engineered and natural barriers as the backfill and coverage layers will compose the disposal system of a near surface repository, concept proposed by the 'RBMN Project'. The use of these barriers aims to avoid or restrict the release of radionuclides from the waste to the human beings and environment. The waterproofing barriers are composed of clays. Certainly, for the national repository, will be used those clays existing in the place where it will be constructed. Them some basic tests will have to be carried out to verify the suitability of these clays as barriers. These tests were determined and performed with reference clay, a Brazilian bentonite constituted of 67.2% montmorillonite. The results were compared with national and international literature of materials with similar mineralogical features. The values found with 95% of confidence interval were 9.73±0,35 μm for granulometric size; 13,3±0,6% for the moisture content and 816±9 mmol.kg{sup -1} for the capacity of cationic exchange. A protocol for characterization of clay was elaborated presenting these tests for it future use. (author)

The Yucca Mountain Repository - Too Little, Too Late

International Nuclear Information System (INIS)

Eriksson, L.G.; Pentz, D.L.

2009-01-01

In 2008, the U.S. Department of Energy (US DOE) announced that the nation's first (and only pursued) deep geological disposal system (repository) for 70,000 metric tonnes of spent nuclear fuel (SNF) and other high-level radioactive waste (HLW) at the Yucca Mountain (YM) site in Nevada would: 1. Not be able to accommodate the projected stockpile of utility-generated SNF beyond 2010. 2. Open no earlier than in 2020, i.e., more than 22 years behind the statutory-mandated opening date. In the meantime, the US DOE is legally obligated to compensate the utilities from January 31, 1998, until it takes title to the utilities' SNF. In 2005 when the YM SNF repository was projected to open in 2010, the utilities estimated that, depending upon how close to 2010 the YM repository opened, the 'breach-of-contract' compensation could be in the range of between 100 billion and 300 billion U.S. dollars ($300 B), which would exceed the 2008 projected life-cycle cost of $96 B for the YM repository. It thus seems appropriate to look beyond the YM repository and call upon the U.S. Congress to promptly act and open new avenues allowing the US DOE to more timely and cost-effectively take title to both existing and pending SNF the current fleet of 104 reactors will generate through the next 60 years. Options for SNF arising from an additional 50 reactors should also be provided. Based on our more than 60 years of combined involvement in nuclear waste management in the USA and abroad, we submit the following industrial-scale-proven, repository-related, nuclear-waste-management and disposition solutions for prompt Congressional consideration and action: 1. An increase in the disposal capacity (and perhaps mission) of the YM repository. 2. Prompt establishment of at least one large federal monitored retrievable storage (MRS) facility for utility-generated SNF. 3. Continued research in reprocessing options of existing and pending SNF with defined milestones. 4. Resurrection of a second

Social impacts of hazardous and nuclear facilities and events: Implications for Nevada and the Yucca Mountain high-level nuclear waste repository; [Final report

Energy Technology Data Exchange (ETDEWEB)

Freudenburg, W.R. [Wisconsin Univ., Madison, WI (United States); Carter, L.F.; Willard, W. [Washington State Univ., Pullman, WA (United States); Lodwick, D.G. [Miami Univ., Oxford, OH (United States); Hardert, R.A. [Arizona State Univ., Tempe, AZ (United States); Levine, A.G. [State Univ. of New York, Buffalo, NY (United States). Dept. of Sociology; Kroll-Smith, S. [New Orleans Univ., LA (United States); Couch, S.R. [Pennsylvania State Univ., University Park, PA (United States); Edelstein, M.R. [Ramapo College, Mahwah, NJ (United States)

1992-05-01

Social impacts of a nuclear waste repository are described. Various case studies are cited such as Rocky Flats Plant, the Feed Materials Production Center, and Love Canal. The social impacts of toxic contamination, mitigating environmental stigma and loss of trust are also discussed.

The impact of episodic nonequilibrium fracture-matrix flow on geological repository performance

International Nuclear Information System (INIS)

Buscheck, T.A.; Nitao, J.J.; Chestnut, D.A.

1991-01-01

Adequate representation of fracture-matrix interaction during episodic infiltration events is crucial in making valid hydrological predictions of repository performance at Yucca Mountain. Various approximations have been applied to represent fracture-matrix flow interaction, including the Equivalent Continuum Model (ECM), which assumes capillary equilibrium between fractures and matrix, and the Fracture-Matrix Model (FMM), which accounts for nonequilibrium fracture-matrix flow. We analyze the relative impact of matrix imbibition on episodic nonequilibrium fracture-matrix flow for the eight major hydrostratigraphic units in the unsaturated zone at Yucca Mountain. Comparisons are made between ECM and FMM predictions to determine the applicability of the ECM. The implications of nonequilibrium fracture-matrix flow on radionuclide transport are also discussed

Preliminary safety analysis of the Baita Bihor radioactive waste repository, Romania

International Nuclear Information System (INIS)

Little, Richard; Bond, Alex; Watson, Sarah; Dragolici, Felicia; Matyasi, Ludovic; Matyasi, Sandor; Naum, Mihaela; Niculae, Ortenzia; Thorne, Mike

2007-01-01

A project funded under the European Commission's Phare Programme 2002 has undertaken an in-depth analysis of the operational and post-closure safety of the Baita Bihor repository. The repository has accepted low- and some intermediate-level radioactive waste from industry, medical establishments and research activities since 1985 and the current estimate is that disposals might continue for around another 20 to 35 years. The analysis of the operational and post-closure safety of the Baita Bihor repository was carried out in two iterations, with the second iteration resulting in reduced uncertainties, largely as a result taking into account new information on the hydrology and hydrogeology of the area, collected as part of the project. Impacts were evaluated for the maximum potential inventory that might be available for disposal to Baita Bihor for a number of operational and postclosure scenarios and associated conceptual models. The results showed that calculated impacts were below the relevant regulatory criteria. In light of the assessment, a number of recommendations relating to repository operation, optimisation of repository engineering and waste disposals, and environmental monitoring were made. (authors)

Study on the locational criteria for submarine rock repositories of low and medium level radioactive wastes

Energy Technology Data Exchange (ETDEWEB)

Kim, G H; Kang, W J; Kim, T J. and others [Chungnam National Univ., Taejon (Korea, Republic of)

1992-01-15

Submarine repositories have significant advantages over their land counterparts locating close to the areas of daily human activities. Consequently, the construction of submarine repositories on the vast continental shelves around Korean seas is considered to be highly positive. In this context, the development of locational criteria primarily targeting the safety of submarine rock repositories is very important.The contents of the present study are: analyzing characteristics of marine environment: Search of potential hazards to, and environmental impact by, the submarine repositories; Investigation of the oceanographic, geochemical, ecological and sedimentological characteristics of estuaries and coastal seas. Locating potential hazards to submarine repositories by: Bibliographical search of accidents leading to the destruction of submarine structures by turbidity currents and other potentials; Review of turbidity currents. Consideration of environmental impact caused by submarine repositories: Logistics to minimize the environmental impacts in site selection; Removal and dispersion processes of radionuclides in sea water. Analyses of oceanographical characteristics of, and hazard potentials in, the Korean seas. Evaluation of the MOST 91-7 criteria for applicability to submarine repositories and the subsequent proposition of additional criteria.

Study on the locational criteria for submarine rock repositories of low and medium level radioactive wastes

International Nuclear Information System (INIS)

Kim, G. H.; Kang, W. J.; Kim, T. J. and others

1992-01-01

Submarine repositories have significant advantages over their land counterparts locating close to the areas of daily human activities. Consequently, the construction of submarine repositories on the vast continental shelves around Korean seas is considered to be highly positive. In this context, the development of locational criteria primarily targeting the safety of submarine rock repositories is very important.The contents of the present study are: analyzing characteristics of marine environment: Search of potential hazards to, and environmental impact by, the submarine repositories; Investigation of the oceanographic, geochemical, ecological and sedimentological characteristics of estuaries and coastal seas. Locating potential hazards to submarine repositories by: Bibliographical search of accidents leading to the destruction of submarine structures by turbidity currents and other potentials; Review of turbidity currents. Consideration of environmental impact caused by submarine repositories: Logistics to minimize the environmental impacts in site selection; Removal and dispersion processes of radionuclides in sea water. Analyses of oceanographical characteristics of, and hazard potentials in, the Korean seas. Evaluation of the MOST 91-7 criteria for applicability to submarine repositories and the subsequent proposition of additional criteria

The convention planning process: Potential impact of a high-level Nuclear Waste Repository in Nevada

International Nuclear Information System (INIS)

Kunreuther, H.; Easterling, D.; Kleindorfer, P.

1988-09-01

This report presents results from two studies that test whether a high level nuclear waste repository sites at Yucca Mountain, Nevada will diminish the willingness of meeting planners to schedule conventions, trade shows, and other meetings in Las Vegas. The first study, a focus group interview with nine meeting planners from the Philadelphia area, found little evidence that planners' selection decisions would be influenced by environmental hazards (e.g., earthquakes, pollution), unless planners were led to believe that these hazards would have a direct impact on convention delegates and the planner could conceivably be held personally responsible for any such impacts. Participants did point out that they would be sensitive to continued media coverage of a negative event, as this might stigmatize the city in the eyes of delegates. The results from the focus group guided the development of a larger and more formal questionnaire survey of meeting planners who were known to have selected Las Vegas for a meeting. Of the 153 planners recruited, 114 had a future meeting scheduled and 39 had arranged a meeting that was recently held in the city. Subjects first answered a number of questions that described the process by which they chose Las Vegas among the possible convention cities. They were then instructed to reconsider their decision in light of seven different scenarios pertaining to the repository at Yucca Mountain

Local-scale modelling of density-driven flow for the phases of repository operation and post-closure at Beberg

International Nuclear Information System (INIS)

Jaquet, O.; Siegel, P.

2004-09-01

A hydrogeological model was developed for Beberg with the aim of evaluating the impact of a repository (for the operational and post-closure phases) while accounting for the effects of density-driven flow. Two embedded scales were taken into account for this modelling study: a local scale at which the granitic medium was considered as a continuum and a repository scale, where the medium is fractured and therefore was regarded to be discrete. The following step-wise approach was established to model density-driven flow at both repository and local scale: (a) modelling fracture networks at the repository scale, (b) upscaling the hydraulic properties to a continuum at local scale and (c) modelling density-driven flow to evaluate repository impact at local scale. The results demonstrate the strong impact of the repository on the flow field during the phase of operation. The distribution of the salt concentration is affected by a large upcoming effect with increased relative concentration and by the presence of fracture zones carrying freshwater from the surface. The concentrations obtained for the reference case, expressed in terms of percentage with respect to the maximum (prescribed) value in the model, are as follows: ca 30% for the phase of desaturation, and ca 20% for the resaturation phase. For the reference case, the impact of repository operations appears no longer visible after a resaturation period of about 20 years after repository closure; under resaturation conditions, evidence of the operational phase has already disappeared in terms of the observed hydraulic and concentration fields. Sensitivity calculations have proven the importance of explicitly discretising repository tunnels when assessing resaturation time and maximum concentration values. Furthermore, the definition of a fixed potential as boundary condition along the model's top surface is likely to provide underestimated values for the maximum concentration and overestimated flow rates in the

CAPACITY BUILDING PROCESS IN ENVIRONMENTAL AND HEALTH IMPACT ASSESSMENT FOR A THAI COMMUNITY.

Science.gov (United States)

Chaithui, Suthat; Sithisarankul, Pornchai; Hengpraprom, Sarunya

2017-03-01

This research aimed at exploring the development of the capacitybuilding process in environmental and health impact assessment, including the consideration of subsequent, capacity-building achievements. Data were gathered through questionnaires, participatory observations, in-depth interviews, focus group discussions, and capacity building checklist forms. These data were analyzed using content analysis, descriptive statistics, and inferential statistics. Our study used the components of the final draft for capacity-building processes consisting of ten steps that were formulated by synthesis from each respective process. Additionally, the evaluation of capacity building levels was performed using 10-item evaluation criteria for nine communities. The results indicated that the communities performed well under these criteria. Finally, exploration of the factors influencing capacity building in environmental and health impact assessment indicated that the learning of community members by knowledge exchange via activities and study visits were the most influential factors of the capacity building processes in environmental and health impact assessment. The final revised version of capacitybuilding process in environmental and health impact assessment could serve as a basis for the consideration of interventions in similar areas, so that they increased capacity in environmental and health impact assessments.

Monitored retrievable storage (MRS) facility and salt repository integration: Engineering study report

International Nuclear Information System (INIS)

1987-07-01

This MRS Facility and Salt Repository Integration Study evaluates the impacts of an integrated MRS/Salt Repository Waste Management System on the Salt Repository Surface facilities' design, operations, cost, and schedule. Eight separate cases were studied ranging from a two phase repository design with no MRS facility to a design in which the repository only received package waste from the MRS facility for emplacement. The addition of the MRS facility to the Waste Management System significantly reduced the capital cost of the salt repository. All but one of the cases studied were capable of meeting the waste acceptance data. The reduction in the size and complexity of the Salt Repository waste handling building with the integration of the MRS facility reduces the design and operating staff requirements. 7 refs., 35 figs., 43 tabs

Assessment of impact to non-human biota from a generic waste repository in the UK

International Nuclear Information System (INIS)

Smith, K.L.; Robinson, C.A.; Jones, S.R.; Batlle, J.V.; Norris, S.

2008-01-01

The UK Nuclear Decommissioning Authority Radioactive Waste Management Directorate (NDA RWMD, formerly Nirex UK Ltd), has played a leading role in establishing knowledge on geological disposal of radioactive waste in the UK. In 2001, a study was commissioned of the potential impact of releases of radio-nuclides from a generic repository on plants and animals). More recently, the NDA commissioned Enviros Consulting to report on developments in policy and in approaches for assessing impacts of radioactivity on non-human biota, that have occurred since the previous study. A trial application of the ERICA assessment tool, to reassess the impact of releases from a generic deep repository using similar source data as used previously (Nirex, 2003), formed part of this work. This paper summarizes the results of the reassessment exercise; key differences between the two assessments are identified and explored. The applicability and capabilities of the ERICA tool to assessments of releases from a waste repository are discussed and priorities for future work are identified. Conclusions: The peak activity concentrations predicted to arise from releases from a generic repository would not lead to a significant increase in environmental risk. Indeed, a substantial proportion of the calculated dose rates are due to natural series radio-nuclides at concentrations that are well below typical background levels. In the previous study, the highest (weighted) absorbed dose rate in an aquatic system was predicted to be around 6.5 micoGy h -1 , which is of the same order of magnitude as those predicted in the current study; the significance of the contribution of natural series radionuclides is also common to both studies. However, previously, the authors concluded that it was not possible to undertake a detailed assessment for the terrestrial system, due to the paucity of data on concentration ratios. While the derivation of default concentration factors, as part of the ERICA project

Aspects on the gas generation and migration in repositories for high level waste in salt formations

International Nuclear Information System (INIS)

Ruebel, Andre; Buhmann, Dieter; Meleshyn, Artur; Moenig, Joerg; Spiessl, Sabine

2013-07-01

In a deep geological repository for high-level waste, gases may be produced during the post-closure phase by several processes. The generated gases can potentially affect safety relevant features and processes of the repository, like the barrier integrity, the transport of liquids and gases in the repository and the release of gaseous radionuclides from the repository into the biosphere. German long-term safety assessments for repositories for high-level waste in salt which were performed prior 2010 did not explicitly consider gas transport and the consequences from release of volatile radionuclides. Selected aspects of the generation and migration of gases in repositories for high-level waste in a salt formation are studied in this report from the viewpoint of the performance assessment. The knowledge on the availability of water in the repository, in particular the migration of salt rock internal fluids in the temperature field of the radioactive waste repository towards the emplacement drifts, was compiled and the amount of water was roughly estimated. Two other processes studied in this report are on the one hand the release of gaseous radionuclides from the repository and their potential impact in the biosphere and on the other hand the transport of gases along the drifts and shafts of the repository and their interaction with the fluid flow. The results presented show that there is some gas production expected to occur in the repository due to corrosion of container material from water disposed of with the backfill and inflowing from the host rock during the thermal phase. If not dedicated gas storage areas are foreseen in the repository concept, these gases might exceed the storage capacity for gases in the repository. Consequently, an outflow of gases from the repository could occur. If there are failed containers for spent fuel, radioactive gases might be released from the containers into the gas space of the backfill and subsequently transported together

Accelerator assisted repositories, technical issue identification and economic assessment

Energy Technology Data Exchange (ETDEWEB)

Myers, T.; Favale, A.; Berwald, D. [Northrop Grumman Corp., Bethpage, NY (United States)

1995-12-31

An investigation (technical and economic) is presented to quantify the impact of accelerator assisted repository (AAR) system on the US national nuclear repository strategy. An overview of US spent fuel policy is presented which provides a means to comparatively assess competing spent fuel disposition technologies under investigation. The advantages of an AAR system are highlighted and discussed. A companion economic analysis is presented. The results indicate that although a US geologic waste repository will continue to be required, waste partitioning and accelerator transmutation of selected actinides, and long-lived fission products, can result in substantial benefits. (author) 18 refs.

Economic impacts associated with pure taxable capacity changes

International Nuclear Information System (INIS)

Bjornstad, D.J.

1978-01-01

An attempt is made to broaden the purview of fiscal impact analysis to include impacts on the local private sector that may stem from local public sector changes. More specifically, attention is focused on the limiting case, in which new private sector development yields positive changes in fiscal capacity, but does not increase public service demands or interact with the local private sector. This phenomenon is termed a ''pure'' change in fiscal capacity, or, stated differently, pure tax revenue importation. Interest in this issue stems from an analysis of the local impacts of constructing and operating nuclear power stations. Nuclear power stations, like other electrical generating facilities, are characterized by large capital-labor ratios, implying that the impact of siting would be to increase local taxable capacity, via the property tax base, to a greater extent than local private sector activity, via new hirings. Moreover, a small labor force implies a modest change in the demand for local public services, and facilities of this nature by themselves demand few, if any, public services. A nuclear power station, however, may be distinguished from other electrical generating facilities through siting regulations that require locating in a low population density area, a fact which ensures the influence on the community will be substantial. The question of how and to what degree feedback effects from local public to local private sector may take place is described

High level waste repository site suitability criteria. Environmental impact statement methodology

International Nuclear Information System (INIS)

1977-06-01

The approach (methodology) which has been developed for the preparation of the environmental impact statement (EIS) is described. A suggested outline is presented for the High Level Waste Repository Site Suitability Criteria EIS together with a detailed description of the approach to be used in preparing the EIS. In addition, a methodology is presented by which the necessary cost/benefit/risk comparisons of alternative sets of site suitability criteria can be made. The TERA environmental research data bank, a computerized data bank which contained information on current and historical licensing activities for power plants was modified to include information on generic or programmatic EIS related issues. The content of the modified data bank was utilized to develop the EIS outline presented in this report. The report recommends that a modified matrix evaluation approach be used to make the cost/benefit/risk comparisons. The suggested matrix is designed to facilitate between criteria comparative analyses of economic, environmental, sociological and radiological risk factors. The quantitative compositing of dollar cost and benefits, environmental and sociological impacts, and radiological risks is to be performed using a semi-analytical, semi-visual procedure based on the concept of ''decision surfaces.''

Evaluating the Long-Term Safety of a Repository at Yucca Mountain

International Nuclear Information System (INIS)

Luik, Abe Van

2002-01-01

Regulations require that the repository be evaluated for its health and safety effects for 10,000 years for the Site Recommendation process. Regulations also require potential impacts to be evaluated for up to a million years in an Environmental Impact Statement. The Yucca Mountain Project is in the midst of the Site Recommendation process. The Total System Performance Assessment (TSPA) that supports the Site Recommendation evaluated safety for these required periods of time. Results showed it likely that a repository at this site could meet the licensing requirements promulgated by the Nuclear Regulatory Commission. The TSPA is the tool that integrates the results of many years of scientific investigations with design information to allow evaluations of potential far-future impacts of building a Yucca Mountain repository. Knowledge created in several branches of physics is part of the scientific basis of the TSPA that supports the Site Recommendation process.

International perspective on repositories for low level waste

International Nuclear Information System (INIS)

Bergstroem, Ulla; Pers, Karin; Almen, Ylva

2011-12-01

represent a common type of locality for a repository, given that siting criteria are fulfilled. There is also a site that was selected without any association to existing nuclear sites or mines. This is the case for the French L'Aube repository. National repositories for disposal of all waste arising in that country are common, e.g. El Cabril in Spain and Low Level Repository close to Drigg in United Kingdom. The depth of the repositories varies from being on the surface to down to 650 metres below ground. The geological conditions of the different repositories are described as well as engineered barriers, geographical location and, if available, information on safety analysis. It can be noted that in the safety analysis of repositories located close to the coast (such as in Sweden, Finland and the United Kingdom), the effect of post-glacial land rise or coastal erosion is taken into special consideration. In general, the size of the repository reflects the size of the nuclear programmes in the respective country. The activity content of the facility, both the total and normalised figures against the volume capacities, are compared for groups of radionuclides

International perspective on repositories for low level waste

Energy Technology Data Exchange (ETDEWEB)

Bergstroem, Ulla; Pers, Karin; Almen, Ylva (SKB International AB (Sweden))

2011-12-15

represent a common type of locality for a repository, given that siting criteria are fulfilled. There is also a site that was selected without any association to existing nuclear sites or mines. This is the case for the French L'Aube repository. National repositories for disposal of all waste arising in that country are common, e.g. El Cabril in Spain and Low Level Repository close to Drigg in United Kingdom. The depth of the repositories varies from being on the surface to down to 650 metres below ground. The geological conditions of the different repositories are described as well as engineered barriers, geographical location and, if available, information on safety analysis. It can be noted that in the safety analysis of repositories located close to the coast (such as in Sweden, Finland and the United Kingdom), the effect of post-glacial land rise or coastal erosion is taken into special consideration. In general, the size of the repository reflects the size of the nuclear programmes in the respective country. The activity content of the facility, both the total and normalised figures against the volume capacities, are compared for groups of radionuclides

Release consequence analysis for a hypothetical geologic radioactive waste repository in hard rock

International Nuclear Information System (INIS)

1979-12-01

This report makes an evaluation of the long-term behaviour of the wastes placed in a hard rock repository. Impacts were analyzed for the seven reference fuel cycles of WG 7. The reference repository for this study is for granitic rock or gneiss as the host rock. The descriptions of waste packages and repository facilities used in this study represent only one of many possible designs based on the multiple barriers concept. The repository's size is based on a nuclear economy producing 100 gigawatts of electricity per year for 1 year. The objective of the modeling efforts presented in this study is to predict the rate of transport of radioactive contaminants from the repository through the geosphere to the biosphere and thus determine an estimate of the potential dose to humans so that the release consequence impacts of the various fuel cycles can be compared. Currently available hydrologic, leach, transport, and dose models were used in this study

Czech Republic. Dukovany repository

International Nuclear Information System (INIS)

2001-01-01

Full text: The repository at the Dukovany site is a structure located above the land surface. It consists of two double-rows of reinforced concrete vaults. Each double-row has dimensions 38x160x6 meters and contains 2x28 vaults. The internal dimensions of each vault are 18x6x5.4 meters. The repository serves for reactor wastes from the Dukovany and Temelin nuclear power plants (NPPs). Its capacity is 55,000 m 3 or 130,000 drums. The repository is a fully engineered facility with multiple barriers. The first engineered barrier is the waste form (in the case of waste from the Dukovany NPP, the waste form is mainly bitumen, but concrete and glass are also considered as suitable solidification products). The second barrier is the container (a 200 litre steel drum or a HIC container), whereas the third consists of cut-off reinforced concrete walls with asphalt-based hydro-insulation. The fourth barrier is a cap which should protect the vaults against infiltration of rainwater and should serve also as an intrusion and erosion barrier. The fifth barrier is a drainage system around the repository which is composed of layers of gravel and sand. The void space in drums around the waste is filled with specially composed grout. Such waste packages are emplaced into the disposal vault, which is covered by pre-fabricated panels. Thereafter, joints between the panels are sealed and a provisional coverage added; the final cover, however, will be constructed only over the whole row of 28 vaults, until all vaults are filled with waste. The final cover will encompass the following components: reinforced concrete pre-fabricated panels (500 mm); cement overcoat (30 mm); insulation foil; concrete layer for cap levelling (5-150 mm); layer of asphalto-propylene concrete (150 mm); soil (450 mm); geotextile foil with topsoil (top surface vegetation). (author)

Structural capacity assessment of a generic pre-stressed concrete containment structure under aircraft impact

International Nuclear Information System (INIS)

Iliev, Alexander

2013-01-01

The studied containment expressed adequate capacity to resist impact loads in the upper range of the studied diapason. The aircraft impact capacity of the containment for impact in the upper part of the cylindrical shell is about 25‐30% higher than the capacity for impact in the middle part of the cylindrical shell. The obtained fragility curves reefed to MoA can be then used for various additional calculations in the safety assessment of nuclear facilities under aircraft impact

Nuclear waste repository in basalt: preconceptual design guidelines

International Nuclear Information System (INIS)

1979-06-01

The development of the basalt waste isolation program parallels the growing need for permanent, environmentally safe, and secure means to store nuclear wastes. The repository will be located within the Columbia Plateau basalt formations where these ends can be met and radiological waste can be stored. These wastes will be stored such that the wastes may be retrieved from storage for a period after placement. After the retrieval period, the storage locations will be prepared for terminal storage. The terminal storage requirements will include decommissioning provisions. The facility boundaries will encompass no more than several square miles of land which will be above a subsurface area where the geologic makeup is primarily deep basaltic rock. The repository will receive, from an encapsulation site(s), nuclear waste in the form of canisters (not more than 18.5 feet x 16 inches in diameter) and containers (55-gallon drums). Canisters will contain spent fuel (after an interim 5-year storage period), solidified high-level wastes (HLW), or intermediate-level wastes (ILW). The containers (drums) will package the low-level transuranic wastes (LL-TRU). The storage capacity of the repository will be expanded in a time-phased program which will require that subsurface development (repository expansion) be conducted concurrently with waste storage operations. The repository will be designed to store the nuclear waste generated within the predictable future and to allow for reasonable expansion. The development and assurance of safe waste isolation is of paramount importance. All activities will be dedicated to the protection of public health and the environment. The repository will be licensed by the US Nuclear Regulatory Commission (NRC). Extensive efforts will be made to assure selection of a suitable site which will provide adequate isolation

Nuclear waste repository in basalt: preconceptual design guidelines

Energy Technology Data Exchange (ETDEWEB)

1979-06-01

The development of the basalt waste isolation program parallels the growing need for permanent, environmentally safe, and secure means to store nuclear wastes. The repository will be located within the Columbia Plateau basalt formations where these ends can be met and radiological waste can be stored. These wastes will be stored such that the wastes may be retrieved from storage for a period after placement. After the retrieval period, the storage locations will be prepared for terminal storage. The terminal storage requirements will include decommissioning provisions. The facility boundaries will encompass no more than several square miles of land which will be above a subsurface area where the geologic makeup is primarily deep basaltic rock. The repository will receive, from an encapsulation site(s), nuclear waste in the form of canisters (not more than 18.5 feet x 16 inches in diameter) and containers (55-gallon drums). Canisters will contain spent fuel (after an interim 5-year storage period), solidified high-level wastes (HLW), or intermediate-level wastes (ILW). The containers (drums) will package the low-level transuranic wastes (LL-TRU). The storage capacity of the repository will be expanded in a time-phased program which will require that subsurface development (repository expansion) be conducted concurrently with waste storage operations. The repository will be designed to store the nuclear waste generated within the predictable future and to allow for reasonable expansion. The development and assurance of safe waste isolation is of paramount importance. All activities will be dedicated to the protection of public health and the environment. The repository will be licensed by the US Nuclear Regulatory Commission (NRC). Extensive efforts will be made to assure selection of a suitable site which will provide adequate isolation.

Learning Object Repositories

Science.gov (United States)

Lehman, Rosemary

2007-01-01

This chapter looks at the development and nature of learning objects, meta-tagging standards and taxonomies, learning object repositories, learning object repository characteristics, and types of learning object repositories, with type examples. (Contains 1 table.)

Assessment of the long-term safety of repositories. Scientific basis

International Nuclear Information System (INIS)

Noseck, Ulrich; Becker, Dirk; Fahrenholz, Christine

2008-12-01

The project contributed to increase the scientific knowledge on the long-term safety assessment and the safety cases of a radioactive waste repository. International guidelines and more recent safety cases from other countries were evaluated. The feasibility study of the three safety indicators ''individual dose rate'', ''radiotoxicity concentration in the biosphere water'' and ''radiotoxicity flux from the geosphere'' showed that due to the independently derived corresponding reference values these indicators describe three different safety statements. The combination of the three values can give a stronger argument for the safety of the repository system. Another important methodological aspect of the safety cases is the definition and selection of scenarios, one of these the human intrusion scenario. Various human intrusion scenarios are considered in the different nations, which differ significantly with respect to type and time scale, the exposition type and exposition pathway. Further progress has been achieved in how to treat human intrusion scenarios in a German post-closure safety case. Another port of the project dealt with the impact of specific geochemical processes on the long-term safety of the repository. The impact of climate changes on the long-term safety of a radioactive waste repository in rock salt was investigated with respect to processes in the overburden and the biosphere where highest impact is expected. Sofa simplified models and only discrete climate estates have been considered

Industrial complementarities between interim storage and reversible geological repository - 59237

International Nuclear Information System (INIS)

Hoorelbeke, Jean-Michel

2012-01-01

The French Act voted in 2006 made the choice of deep geological disposal as the reference option for the long term management of high level (HLW) and intermediate level long-lived waste. The CIGEO repository project aims at avoiding or limiting burden to future generations, which could not be achieved by the extension in time of interim storage. The reversibility as provided by the Act will maintain a liberty of choice for waste management on a duration which is comparable to new storage facility. Interim storage is required to accommodate waste as long as the repository is not available. The commissioning of the repository in 2025 will not suppress needs for interim storage. The paper describes the complementarities between existing and future interim storage facilities and the repository project: repository operational issues and planning, HLW thermal decay, support for the reversibility, etc. It shows opportunities to prepare a global optimization of waste management including the utilization at best of storage capacities and the planning of waste emplacement in the repository in such a way to facilitate operational conditions and to limit cost. Preliminary simulations of storage-disposal scenarios are presented. Thanks to an optimal use of the waste management system, provision can be made for a progressive increase of waste emplacement flow during the first operation phase of the repository. It is then possible to stabilize the industrial activity level of the repository site. An optimal utilization of interim storage can also limit the diversity of waste packages emplaced simultaneously, which facilitates the operation of the repository. 60 years minimum interim storage duration is generally required with respect to HLW thermal output. Extending this interim storage period may reduce the underground footprint of the repository. Regarding reversibility, the capability to manage waste packages potentially retrieved from the repository should be analyzed. The

Images of a place and vacation preferences: Implications of the 1989 surveys for assessing the economic impacts of a nuclear waste repository in Nevada

International Nuclear Information System (INIS)

Slovic, P.; Layman, M.; Flynn, J.H.

1990-11-01

In July, 1989 the authors produced a report titled Perceived Risk, Stigma, and Potential Economic Impacts of a High-Level Nuclear-Waste Repository in Nevada (Slovic et al., 1989). That report described a program of research designed to assess the potential impacts of a high-level nuclear waste repository at Yucca Mountain, Nevada upon tourism, retirement and job-related migration, and business development in Las Vegas and the state. It was concluded that adverse economic impacts potentially may result from two related social processes. Specifically, the study by Slovic et al. employed analyses of imagery in order to overcome concerns about the validity of direct questions regarding the influence of a nuclear-waste repository at Yucca Mountain upon a person's future behaviors. During the latter months of 1989, data were collected in three major telephone surveys, designed to achieve the following objectives: (1) to replicate the results from the Phoenix, Arizona, surveys using samples from other populations that contribute to tourism, migration, and development in Nevada; (2) to retest the original Phoenix respondents to determine the stability of their images across an 18-month time period and to determine whether their vacation choices subsequent to the first survey were predictable from the images they produced in that original survey; (3) to elicit additional word-association images for the stimulus underground nuclear waste repository in order to determine whether the extreme negative images generated by the Phoenix respondents would occur with other samples of respondents; and (4) to develop and test a new method for imagery elicitation, based upon a rating technique rather than on word associations. 2 refs., 8 figs., 13 tabs

Radioactive Waste Repositories and Incentives to Local Communities

International Nuclear Information System (INIS)

Knapp, A.; Medakovic, S.

2008-01-01

repository compensations, it may be useful to analyze the appropriateness and effectiveness of the Slovenian compensations concept, and also to consider its relative significance in other communities with prospective repository sites. Relative impact to local budgets may be assessed against other approaches to increased public acceptance, such as confidence building and indirect benefits from the repository to local economies.(author)

Planning and Design Considerations for Geological Repository Programmes of Radioactive Waste

International Nuclear Information System (INIS)

2014-11-01

Disposal in a geological repository is the generally accepted solution for the long term management of high level and/or long lived radioactive wastes, in line with the general principles defined in the IAEA Safety Fundamentals. This publication presents practical information on the way a geological repository programme for radioactive waste could be defined and planned, with special attention to all aspects having an impact on the timing. Country specific examples for repository development phases are provided, based on actual experiences from Member States

Hydrological and hydrogeological effects of an open repository in Forsmark. Final MIKE SHE flow modelling results for the Environmental Impact Assessment

International Nuclear Information System (INIS)

Maartensson, Erik; Gustafsson, Lars-Goeran

2010-07-01

This report presents methodology and modelling results concerning a deep-rock repository for spent nuclear fuel in Forsmark. Specifically, the modelling tools MIKE SHE, MIKE 11 and MOUSE are used to quantify the groundwater inflow to the repository and associated hydrological and hydrogeological effects during the construction and operation phases. The modelling results presented in the report provide input to the Environmental Impact Assessment (EIA) that will be part of a permit application according to the Environmental Code. Based on an existing MIKE SHE model for Forsmark, the first step of the modelling process was to implement an updated hydrogeological model of the bedrock and to increase the vertical and horizontal extents of the model domain. Other model updates involve the vegetation classification, and implementation of SFR (final repository for short-lived radioactive waste) and the subsurface drainage system at the nearby nuclear power plant. The updated model was calibrated using measured data on groundwater levels in the Quaternary deposits and the bedrock, water levels in lakes, and stream discharges. The calibrated model was then used for simulation of undisturbed conditions (i.e. without the repository) as a reference for modelling results obtained for disturbed conditions (with the repository). The modelling results for undisturbed conditions that are presented in the report closely resemble those of the final MIKE SHE site descriptive modelling (SDM-Site Forsmark). The repository layout was implemented as pipe links (segments) in the modelling tool MOUSE, and the implemented layout was used for the modelling of disturbed conditions. The study uses an updated and verified MIKE SHE-MOUSE coupling routine that is specifically adapted for calculation of groundwater inflow to grouted rock tunnels. The vertical shafts of the repository are implemented in the form of MIKE SHE grid cells with atmospheric pressure. Modelling results for disturbed

Hydrological and hydrogeological effects of an open repository in Forsmark. Final MIKE SHE flow modelling results for the Environmental Impact Assessment

Energy Technology Data Exchange (ETDEWEB)

Maartensson, Erik; Gustafsson, Lars-Goeran (DHI Sverige AB (Sweden))

2010-07-15

This report presents methodology and modelling results concerning a deep-rock repository for spent nuclear fuel in Forsmark. Specifically, the modelling tools MIKE SHE, MIKE 11 and MOUSE are used to quantify the groundwater inflow to the repository and associated hydrological and hydrogeological effects during the construction and operation phases. The modelling results presented in the report provide input to the Environmental Impact Assessment (EIA) that will be part of a permit application according to the Environmental Code. Based on an existing MIKE SHE model for Forsmark, the first step of the modelling process was to implement an updated hydrogeological model of the bedrock and to increase the vertical and horizontal extents of the model domain. Other model updates involve the vegetation classification, and implementation of SFR (final repository for short-lived radioactive waste) and the subsurface drainage system at the nearby nuclear power plant. The updated model was calibrated using measured data on groundwater levels in the Quaternary deposits and the bedrock, water levels in lakes, and stream discharges. The calibrated model was then used for simulation of undisturbed conditions (i.e. without the repository) as a reference for modelling results obtained for disturbed conditions (with the repository). The modelling results for undisturbed conditions that are presented in the report closely resemble those of the final MIKE SHE site descriptive modelling (SDM-Site Forsmark). The repository layout was implemented as pipe links (segments) in the modelling tool MOUSE, and the implemented layout was used for the modelling of disturbed conditions. The study uses an updated and verified MIKE SHE-MOUSE coupling routine that is specifically adapted for calculation of groundwater inflow to grouted rock tunnels. The vertical shafts of the repository are implemented in the form of MIKE SHE grid cells with atmospheric pressure. Modelling results for disturbed

Potential impact of Andrassy bentonite microbial diversity in the long-term performance of a deep nuclear waste repository

Science.gov (United States)

Tadza, M. Y. Mohd; Tadza, M. A. Mohd; Bag, R.; Harith, N. S. H.

2018-01-01

Copper and steel canning and bentonite buffer are normally forseen as the primary containment component of a deep nuclear waste repository. Distribution of microbes in subsurface environments have been found to be extensive and directly or indirectly may exert influence on waste canister corrosion and the mobility of radionuclides. The understanding of clays and microbial interaction with radionuclides will be useful in predicting the microbial impacts on the performance of the waste repositories. The present work characterizes the culture-dependent microbial diversity of Andrassy bentonite recovered from Tawau clay deposits. The evaluation of microbial populations shows the presence of a number of cultivable microbes (e.g. Staphylococcus, Micrococcus, Achromobacter, Bacillus, Paecilomyces, Trichoderma, and Fusarium). Additionally, a pigmented yeast strain Rhodotorula mucilaginosa was also recovered from the formation. Both Bacillus and Rhodotorula mucilaginosa have high tolerance towards U radiation and toxicity. The presence of Rhodotorula mucilaginosa in Andrassy bentonite might be able to change the speciation of radionuclides (e.g. uranium) in a future deep repository. However, concern over the presence of Fe (III) reduction microbes such as Bacillus also found in the formation could lead to corrosion of copper steel canister and affect the overall performance of the containment system.

Repository Rodeo Redux

CERN Document Server

Anez, Melissa; Donohue, Tim; Fyson, Will; Simko, Tibor; Wilcox, David

2017-01-01

You’ve got more repository questions and we’ve got more answers! Last year’s Repository Rodeo panel was a huge success, so we’re taking the show on the road to Brisbane for OR2017. Join representatives from the DSpace, Eprints, Fedora, Hydra, and Islandora communities as we (briefly) explain what each of our repositories actually does. We'll also talk about the directions of our respective technical and community developments, and related to the conference theme of Open: Innovation Knowledge Repositories, offer brief observations about the latest, most promising and/or most surprising innovations in our space. This panel will be a great opportunity for newcomers to Open Repositories to get a crash course on the major repository options and meet representatives from each of their communities. After a brief presentation from each representative, we'll open the session up for questions from the audience.

Developing of Radioactive Wastes Management Safety at Baldone Repository Radons

International Nuclear Information System (INIS)

Abramenkovs, A.; Abramenkova, G.; Klavins, M.

2008-01-01

The near surface radioactive wastes repository Radons near the Baldone city was put in operation in 1962. The safety assessment of repository was performed during 2000-2001 under the PHARE project to evaluate the recommended upgrades of repository. The outline design for new vaults and interim storage for long lived radioactive wastes was elaborated during 2003-2004 years. The Environmental Impact Assessment (EIA) for upgrade of Baldone repository was performed during 2004-2005 years. Additional evaluations of radioactive wastes management safety were performed during 2006 year by the experts of ENRESA, Spain. It was shown, that the additional efforts were spent for improving of radioactive wastes cementation in concrete containers. The results of tritium and Cs 137 leaching studies are presented and discussed. It was shown, that additives can significantly reduce the migration of radionuclides in ground water. The leaching coefficients for tritium and Cs 137 were determined to supply with the necessary data the risk assessment calculations for operation of Baldone repository R adons

EEI/UWASTE oversight of the DOE Repository Program by the Repository Information Exchange Team

International Nuclear Information System (INIS)

Henkel, C.J.; Supko, E.M.; Schwartz, M.H.

1993-01-01

The Utility Nuclear Waste and Transportation Program of the Edison Electric Institute (EEI/UWASTE) has conducted reviews of the US DOE's repository program through its Repository Information Exchange Team (RIET or Team). Eight such reviews have been conducted since 1985 covering topics that include repository program management and control; repository schedule; repository budget; quality assurance; site characterization; repository licensing; environmental issues; and institutional and public information activities. The utility industry has used these repository program reviews as a forum for providing DOE's Office of Civilian Radioactive Waste Management (OCRWM) with comments on the direction of the repository program, advice for future actions regarding quality assurance activities and repository licensing, and suggestions for management and control of the Repository Program. The most significant recommendations made by the utility industry through the RIET are discussed along with any subsequent action by OCRWM in response to or subsequent to utility industry recommendations. The process used by the RIET to develop its recommendations to OCRWM regarding the repository program is also discussed

The Pangea concept for an international radioactive waste repository

International Nuclear Information System (INIS)

Kurzeme, M.

1999-01-01

Pangea Resources Australia Pty. Ltd. is engaged in a study to investigate the feasibility of constructing and operating an international radioactive waste repository in Australia. Western Australia in particular has a unique combination of geology, topography and climate which makes it eminently suitable for a deep geological repository for the safe and permanent disposal of radioactive waste. Australia also has the political, social, legal and financial systems, together with the technical capability to make it acceptable as a host nation for an international repository. This paper reviews the origins of the Pangea concept, describes the high isolation approach to site selection, the Pangea integrated waste management system, together with its potential economic impact on Australia

Novel Methods to Determine Feeder Locational PV Hosting Capacity and PV Impact Signatures

Energy Technology Data Exchange (ETDEWEB)

Reno, Matthew J. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Coogan, Kyle [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Seuss, John [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Broderick, Robert Joseph [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2017-05-01

Often PV hosting capacity analysis is performed for a limited number of distribution feeders. For medium - voltage distribution feeders, previous results generally analyze less than 20 feeders, and then the results are extrapolated out to similar types of feeders. Previous hosting capacity research has often focused on determining a single value for the hosting capacity for the entire feeder, whereas this research expands previous hosting capacity work to investigate all the regions of the feeder that may allow many different hosting capacity values wit h an idea called locational hosting capacity (LHC)to determine the largest PV size that can be interconnected at different locations (buses) on the study feeders. This report discusses novel methods for analyzing PV interconnections with advanced simulati on methods. The focus is feeder and location - specific impacts of PV that determine the locational PV hosting capacity. Feeder PV impact signature are used to more precisely determine the local maximum hosting capacity of individual areas of the feeder. T he feeder signature provides improved interconnection screening with certain zones that show the risk of impact to the distribution feeder from PV interconnections.

Impacts of seismic activity on long-term repository performance at Yucca Mountain

International Nuclear Information System (INIS)

Gauthier, J.H.; Wilson, M.L.; Borns, D.J.; Arnold, B.W.

1995-01-01

Several effects of seismic activity on the release of radionuclides from a potential repository at Yucca Mountain are quantified. Future seismic events are predicted using data from the seismic hazard analysis conducted for the Exploratory Studies Facility (ESF). Phenomenological models are developed, including rockfall (thermal-mechanical and seismic) in unbackfilled emplacement drifts, container damage caused by fault displacement within the repository, and flow-path chance caused by changes in strain. Using the composite-porosity flow model (relatively large-scale, regular percolation), seismic events show little effect on total-system releases; using the weeps flow model (episodic pulses of flow in locally saturated fractures), container damage and flow-path changes cause over an order of magnitude increase in releases. In separate calculations using, more realistic representations of faulting, water-table rise caused by seismically induced changes in strain are seen to be higher than previously estimated by others, but not sufficient to reach a potential repository

A scoping review of online repositories of quality improvement projects, interventions and initiatives in healthcare.

Science.gov (United States)

Bytautas, Jessica P; Gheihman, Galina; Dobrow, Mark J

2017-04-01

Quality improvement (QI) is becoming an important focal point for health systems. There is increasing interest among health system stakeholders to learn from and share experiences on the use of QI methods and approaches in their work. Yet there are few easily accessible, online repositories dedicated to documenting QI activity. We conducted a scoping review of publicly available, web-based QI repositories to (i) identify current approaches to sharing information on QI practices; (ii) categorise these approaches based on hosting, scope and size, content acquisition and eligibility, content format and search, and evaluation and engagement characteristics; and (iii) review evaluations of the design, usefulness and impact of their online QI practice repositories. The search strategy consisted of traditional database and grey literature searches, as well as expert consultation, with the ultimate aim of identifying and describing QI repositories of practices undertaken in a healthcare context. We identified 13 QI repositories and found substantial variation across the five categories. The QI repositories used different terminology (eg, practices vs case studies) and approaches to content acquisition, and varied in terms of primary areas of focus. All provided some means for organising content according to categories or themes and most provided at least rudimentary keyword search functionality. Notably, none of the QI repositories included evaluations of their impact. With growing interest in sharing and spreading best practices and increasing reliance on QI as a key contributor to health system performance, the role of QI repositories is likely to expand. Designing future QI repositories based on knowledge of the range and type of features available is an important starting point for improving their usefulness and impact. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/.

Site selection for deep geologic repositories - Consequences for society, economy and environment

International Nuclear Information System (INIS)

2010-03-01

In a few years, Switzerland will make the decision regarding site selection for geological underground repositories for the storage of radioactive wastes. Besides the safety issue, many citizens are interested in how such a repository will affect environment, economy and society in the selected site's region. This brochure summarizes the results of many studies on the socio-economic impacts of nuclear waste repositories. Radioactive wastes must be stored in such a way that mankind and environment are safely protected for a long period of time. How this goal may be achieved, is already known: geologic deep repositories warrant long-term safety. For the oncoming years in Switzerland the question is where the repository will be built. The search for an appropriate site for a repository in the proposed regions will launch discussions. Within the participative framework the regions may bring their requests. The demonstration of the safety of potential repository sites has the highest priority in the selection process. In the third procedural step additional rock investigations will be made. The socio-economic studies and the experience with existing plants show that radioactive waste management plants can be built and operated in good agreement with environmental requirements. The radioactive wastes in a deep underground repository are stored many hundred meters below the Earth's surface. There, they are isolated from our vital space. Technical barriers and the surrounding dense rock confinement prevent the release of radioactive materials into the environment. A deep repository has positive consequences for the regional economy. It increases trade and value creation and creates work places. The socio-economic impacts practically extend over one century, but strongly vary with time; they are the largest during the building period. High life quality and a positive population development in the selected site region are compatible with a deep repository. A fair and

Radioactive waste transport to a Nirex deep repository

International Nuclear Information System (INIS)

Bennett, D.; Appleton, P.R.; Eastman, C.R.

1989-01-01

Nirex is addressing the transport of radioactive wastes, repository construction materials, personnel and spoil as part of their development of a deep repository. An integrated transport system will be developed for wastes which may involve, road, rail and sea transport. The possible application and the scale of operation of the transport system is described. Environmental impact assessments will be carried out, and the proposed approach to these is described. A methodology for the assessment of transport safety has been established and the results of a preliminary assessment are given. (author)

Trustworthy Digital Repositories: Building Trust the Old Fashion Way, EARNING IT.

Science.gov (United States)

Kinkade, D.; Chandler, C. L.; Shepherd, A.; Rauch, S.; Groman, R. C.; Wiebe, P. H.; Glover, D. M.; Allison, M. D.; Copley, N. J.; Ake, H.; York, A.

2016-12-01

There are several drivers increasing the importance of high quality data management and curation in today's research process (e.g., OSTP PARR memo, journal publishers, funders, academic and private institutions), and proper management is necessary throughout the data lifecycle to enable reuse and reproducibility of results. Many digital data repositories are capable of satisfying the basic management needs of an investigator looking to share their data (i.e., publish data in the public domain), but repository services vary greatly and not all provide mature services that facilitate discovery, access, and reuse of research data. Domain-specific repositories play a vital role in the data curation process by working closely with investigators to create robust metadata, perform first order QC, and assemble and publish research data. In addition, they may employ technologies and services that enable increased discovery, access, and long-term archive. However, smaller domain facilities operate in varying states of capacity and curation ability. Within this repository environment, individual investigators (driven by publishers, funders, or institutions) need to find trustworthy repositories for their data; and funders need to direct investigators to quality repositories to ensure return on their investment. So, how can one determine the best home for valuable research data? Metrics can be applied to varying aspects of data curation, and many credentialing organizations offer services that assess and certify the trustworthiness of a given data management facility. Unfortunately, many of these certifications can be inaccessible to a small repository in cost, time, or scope. Are there alternatives? This presentation will discuss methods and approaches used by the Biological and Chemical Oceanography Data Management Office (BCO-DMO; a domain-specific, intermediate digital data repository) to demonstrate trustworthiness in the face of a daunting accreditation landscape.

Dessicant materials screening for backfill in a salt repository

International Nuclear Information System (INIS)

Simpson, D.R.

1980-10-01

Maintaining an anhydrous environment around nuclear waste stored in a salt repository is a concern which can be alleviated by using a desiccant material for backfilling. Such a desiccant should desiccate a brine yet be non deliquescent, the hydrated product should have moderate thermal stability, and the desiccant should have a high capacity and be readily available. From a literature search MgO and CaO were identified for detailed study. These oxides, and an intimate mixture of the two obtained by calcining dolomite, were used in experiments to further determine their suitability. They proved to be excellent desiccants with a high water capacity. The hydrates of both have moderate thermal stability and a high water content. Both MgO and CaO react in an alkaline chloride brine forming oxychloride compounds with different waters of crystallization. Some of these compounds are the Sorel Cements. CaO hydrates to Ca(OH) 2 which carbonates with CO 2 in air to form CaCO 3 and release the hydrated water. Thus the intimate mixture of CaO and MgO from calcined dolomite may serve as a desiccant and remove CO 2 from the repository atmosphere

Dessicant materials screening for backfill in a salt repository

Energy Technology Data Exchange (ETDEWEB)

Simpson, D.R.

1980-10-01

Maintaining an anhydrous environment around nuclear waste stored in a salt repository is a concern which can be alleviated by using a desiccant material for backfilling. Such a desiccant should desiccate a brine yet be non deliquescent, the hydrated product should have moderate thermal stability, and the desiccant should have a high capacity and be readily available. From a literature search MgO and CaO were identified for detailed study. These oxides, and an intimate mixture of the two obtained by calcining dolomite, were used in experiments to further determine their suitability. They proved to be excellent desiccants with a high water capacity. The hydrates of both have moderate thermal stability and a high water content. Both MgO and CaO react in an alkaline chloride brine forming oxychloride compounds with different waters of crystallization. Some of these compounds are the Sorel Cements. CaO hydrates to Ca(OH)/sub 2/ which carbonates with CO/sub 2/ in air to form CaCO/sub 3/ and release the hydrated water. Thus the intimate mixture of CaO and MgO from calcined dolomite may serve as a desiccant and remove CO/sub 2/ from the repository atmosphere.

An approach to improve Romanian geological repository planning

International Nuclear Information System (INIS)

Andrei, Veronica; Prisecaru, Ilie

2016-01-01

International standards recommend typical phases to be included within any national program for the development of a geological repository dedicated to disposal of the high level radioactive wastes generated in countries using nuclear power. However, these are not universally applicable and the content of each of these phases may need to be adapted for each national situation and regulatory and institutional framework. Several national geological repository programs have faced failures in schedules and have revised their programs to consider an adapted phased management approach. The authors have observed that in the case of those countries in the early phases of a geological repository program where boundary conditions have not been fully defined, international recommendations for handling delays/failures in the national program might not immediately help. This paper considers a case study of the influences of the national context risks on the current planning schedule of the Romanian national geological repository. It proposes an optimum solution for an integrated response to any significant adverse impact arising from these risks, enabling sustainable program planning

Impact of repository depth on residence times for leaking radionuclides in land-based surface water

Science.gov (United States)

Wörman, Anders; Marklund, Lars; Xu, Shulan; Dverstorp, Björn

2007-03-01

The multiple scales of landscape topography produce a wide distribution of groundwater circulation cells that control the hydro-geological environments surrounding geological repositories for nuclear waste. The largest circulation cells tend to discharge water into major river reaches, large freshwater systems or the nearby Baltic Sea. We investigated numerically the release of radionuclides from repositories placed in bedrock with depths between 100 to 2000 meters in a Swedish coastal area and found that leakage from the deeper positions emerges primarily in the major aquatic systems. In effect, radionuclides from the deeper repositories are more rapidly transported towards the Sea by the stream system compared to leakage from more shallow repositories. The release from the shallower repositories is significantly retained in the initial stage of the transport in the (superficial) landscape because the discharge occurs in or near low-order streams with high retention characteristics. This retention and residence time for radioactivity in the landscape control radiological doses to biota and can, thus, be expected to constitute an essential part of an associated risk evaluation.

Buoyancy flow in fractures intersecting a nuclear waste repository

International Nuclear Information System (INIS)

Wang, J.S.Y.; Tsang, C.F.

1980-07-01

The thermally induced buoyancy flow in fractured rocks around a nuclear waste repository is of major concern in the evaluation of the regional, long-term impact of nuclear waste disposal in geological formation. In this study, buoyancy flow and the development of convective cells are calculated in vertical fractures passing through or positioned near a repository. Interaction between buoyancy flow and regional hydraulic gradient is studied as a function of time, and the interference of intersecting fractures with each other is also discussed

Double Diffusive Natural Convection in a Nuclear Waste Repository

International Nuclear Information System (INIS)

Y. Hao; J. Nitao; T.A. Buscheck; Y. Sun

2006-01-01

In this study, we conduct a two-dimensional numerical analysis of double diffusive natural convection in an emplacement drift for a nuclear waste repository. In-drift heat and moisture transport is driven by combined thermal- and compositional-induced buoyancy forces. Numerical results demonstrate buoyancy-driven convective flow patterns and configurations during both repository heat-up and cool-down phases. It is also shown that boundary conditions, particularly on the drip-shield surface, have strong impacts on the in-drift convective flow and transport

Impact of Cyclic Prefix length on OFDM system Capacity

DEFF Research Database (Denmark)

Rom, Christian; Sørensen, Troels Bundgaard; Mogensen, Preben Elgaard

2005-01-01

This paper is a study on the impact of the Cyclic Prefix (CP) length on the downlink Capacity in a base-band synchronized SISO-OFDM context. To measure this impact, the capacity, measured in bits per second per hertz, is chosen as quality parameter. The study shows how the lengthening of the CP......) the useful OFDM symbol duration, 2) the Signal to Noise Ratio (SNR) at the receiver and 3) the channel Power Delay Profile (PDP). Depending on the values of these parameters different optimum CP lengths are obtained. For a system using only one value of CP length we suggest an optimum value to be 4us...... for an OFDM symbol length of 40us and 6us for an OFDM symbol length of 80us....

The SocioEconomic Analysis of Repository Siting (SEARS): Technical description: Final draft

International Nuclear Information System (INIS)

1984-11-01

Socioeconomic impacts must be assessed both for the near term and for the future. One means of addressing the need for the assessment of such impacts has been through the development of the computerized socioeconomic assessment model called the SocioEconomic Analysis of Repository Siting (SEARS) model. The SEARS model was developed for the Battelle Project Management Division. It was refined and adapted from state-of-the-art computerized projection models and thoroughly validated and is now available for use in projecting the likely socioeconomic impacts of a repository facility. This Technical Description is one of six major products that describe the SEARS modeling system. 61 refs., 11 figs., 9 tabs

Determination of Heat Capacity of Yucca Mountain Stratigraphic Layers

International Nuclear Information System (INIS)

T. Hadgu; C. Lum; J.E. Bean

2006-01-01

The heat generated from the radioactive waste to be placed in the proposed geologic repository at Yucca Mountain, Nevada, will affect the thermal-hydrology of the Yucca Mountain stratigraphic layers. In order to assess the effect of the movement of repository heat into the fractured rocks accurate determination of thermodynamic and hydraulic properties is important. Heat capacity is one of the properties that are required to evaluate energy storage in the fractured rock. Rock-grain heat capacity, the subject of this study, is the heat capacity of the solid part of the rock. Yucca Mountain consists of alternating lithostratigraphic units of welded and non-welded ash-flow tuff, mainly rhyolitic in composition and displaying varying degrees of vitrification and alteration. A number of methods exist that can be used to evaluate heat capacity of the stratigraphic layers that consist of different compositions. In this study, the mineral summation method has been used to quantify the heat capacity of the stratigraphic layers based on Kopp's rule. The mineral summation method is an addition of the weighted heat capacity of each mineral found in a specific layer. For this study the weighting was done based on the mass percentage of each mineral in the layer. The method utilized a mineralogic map of the rocks at the Yucca Mountain repository site. The Calico Hills formation and adjacent bedded tuff layers display a bimodal mineral distribution of vitric and zeolitic zones with differing mineralogies. Based on this bimodal distribution in zeolite abundance, the boundary between the vitric and zeolitic zones was selected to be 15% zeolitic abundance. Thus, based on the zeolite abundance, subdivisions have been introduced to these layers into ''vitric'' and ''zeolitic'' zones. Heat capacity values have been calculated for these layers both as ''layer average'' and ''zone average''. The heat capacity determination method presented in this report did not account for spatial

Towards Interoperable Preservation Repositories: TIPR

Directory of Open Access Journals (Sweden)

Priscilla Caplan

2010-07-01

Full Text Available Towards Interoperable Preservation Repositories (TIPR is a project funded by the Institute of Museum and Library Services to create and test a Repository eXchange Package (RXP. The package will make it possible to transfer complex digital objects between dissimilar preservation repositories.  For reasons of redundancy, succession planning and software migration, repositories must be able to exchange copies of archival information packages with each other. Every different repository application, however, describes and structures its archival packages differently. Therefore each system produces dissemination packages that are rarely understandable or usable as submission packages by other repositories. The RXP is an answer to that mismatch. Other solutions for transferring packages between repositories focus either on transfers between repositories of the same type, such as DSpace-to-DSpace transfers, or on processes that rely on central translation services.  Rather than build translators between many dissimilar repository types, the TIPR project has defined a standards-based package of metadata files that can act as an intermediary information package, the RXP, a lingua franca all repositories can read and write.

Repository simulation model: Final report

International Nuclear Information System (INIS)

1988-03-01

This report documents the application of computer simulation for the design analysis of the nuclear waste repository's waste handling and packaging operations. The Salt Repository Simulation Model was used to evaluate design alternatives during the conceptual design phase of the Salt Repository Project. Code development and verification was performed by the Office of Nuclear Waste Isolation (ONWL). The focus of this report is to relate the experience gained during the development and application of the Salt Repository Simulation Model to future repository design phases. Design of the repository's waste handling and packaging systems will require sophisticated analysis tools to evaluate complex operational and logistical design alternatives. Selection of these design alternatives in the Advanced Conceptual Design (ACD) and License Application Design (LAD) phases must be supported by analysis to demonstrate that the repository design will cost effectively meet DOE's mandated emplacement schedule and that uncertainties in the performance of the repository's systems have been objectively evaluated. Computer simulation of repository operations will provide future repository designers with data and insights that no other analytical form of analysis can provide. 6 refs., 10 figs

Impact of advanced fuel cycle options on waste management policies

International Nuclear Information System (INIS)

Gordelier, Stan; Cavedon, Jean-Marc

2006-01-01

OECD/NEA has performed a study on the impact of advanced fuel cycle options on waste management policies with 33 experts from 12 member countries, 1 non-member country and 2 international organizations. The study extends a series of previous ones on partitioning and transmutation (P and T) issues, focusing on the performance assessments for repositories of high-level waste (HLW) arising from advanced fuel cycles. This study covers a broader spectrum than previous studies, from present industrial practice to fully closed cycles via partially closed cycles (in terms of transuranic elements); 9 fuel cycle schemes and 4 variants. Elements of fuel cycles are considered primarily as sources of waste, the internal mass flows of each scheme being kept for the sake of mass conservation. The compositions, activities and heat loads of all waste flows are also tracked. Their impact is finally assessed on the waste repository concepts. The study result confirms the findings from the previous NEA studies on P and T on maximal reduction of the waste source term and maximal use of uranium resources. In advanced fuel cycle schemes the activity of the waste is reduced by burning first plutonium and then minor actinides and also the uranium consumption is reduced, as the fraction of fast reactors in the park is increased to 100%. The result of the repository performance assessments, analysing the effect of different HLW isotopic composition on repository performance and on repository capacity, shows that the maximum dose released to biosphere at any time in normal conditions remains, for all schemes and for all the repository concepts examined, well below accepted radiation protection thresholds. The major impact is on the detailed concept of the repositories, through heat load and waste volume. Advanced fuel cycles could allow a repository to cover waste produced from 5 to 20 times more electricity generation than PWR once-through cycle. Given the flexibility of the advanced fuel

Deep repository for spent nuclear fuel. SR 97 - Post-closure safety. Main Report. Summary

Energy Technology Data Exchange (ETDEWEB)

Hedin, A. [ed.

1999-11-01

buffer, geosphere and biosphere are analyzed in the canister defect scenario. Releases from the geosphere are converted to doses in different ecosystems. The variation in flow-related data in the geosphere has the greatest impact on the result, followed by data uncertainties for the biosphere. Other conclusions are that our understanding of fuel dissolution needs to be improved, and that the probability and size of initial canister defects that escape quality-control inspection is difficult to estimate. Risk analyses in the form of simplified probabilistic calculations are also performed. The risk analyses show that all sites lie well below the acceptance criterion. The maximum risk for release to a well is never more than 0.5 percent of the acceptance criterion, even when the calculations are extended a million years into the future. The same applies to releases to peat land for times up to 100,000 years, while the maximum risk here grows to about one-tenth of the acceptance criterion at the least favourable site at times after 100,000 years. The consequences of future climate change are explored in the climate scenario. A conceivable sequence of events, including severe glaciation, on each of the three sites is sketched for the coming 150,000 years. In the climate scenario as well, the overall conclusion is that the isolating capacity of the copper canister is not threatened by either mechanical or chemical stresses. As far as the retarding capacity of the repository is concerned, for example in the event of initial canister damage, the most important changes take place in the biosphere. The repository sites are expected to be covered by ice sheets or sea during long periods, and the aggregate effect of climate change will therefore be a reduction of the dose consequences compared with a situation where the present-day climate persists. In the earthquake scenario, the consequences of earthquakes are analyzed by means of model studies where site-specific data are used

Considerations for developing seismic design criteria for nuclear waste storage repositories

International Nuclear Information System (INIS)

Owen, G.N.; Yanev, P.I.; Scholl, R.E.

1980-04-01

The function of seismic design criteria is to reduce the potential for hazards that may arise during various stages of the repository life. During the operational phase, the major concern is with the possible effects of earthquakes on surface facilities, underground facilities, and equipment. During the decommissioned phase, the major concern is with the potential effects of earthquakes on the geologic formation, which may result in a reduction in isolation capacity. Existing standards and guides or criteria used for the static and seismic design of licensed nuclear facilities were reviewed and evaluated for their applicability to repository design. This report is directed mainly toward the development of seismic design criteria for the underground structures of repositories. An initial step in the development of seismic design criteria for the underground structures of repositories is the development of performance criteria, or minimum standards of acceptable behavior. A number of possible damage modes are identified for the operating phase of the repository; however, no damage modes are foreseen that would perturb the long-term function of the repository, except for the possibility of increased permeability within the rock mass. Subsequent steps in formulating acceptable seismic design criteria for the underground structures involve the quantification of the design process. The report discusses the necessity of specifying the form of ground motion that would be needed for seismic analysis and the procedures that may be used for making ground motion predictions. Further discussions outline what is needed for analysis, including rock properties, failure criteria, modeling techniques, seismic hardening criteria for the host rock mass, and probabilistic considerations

Logistics Modeling of Emplacement Rate and Duration of Operations for Generic Geologic Repository Concepts

Energy Technology Data Exchange (ETDEWEB)

Kalinina, Elena Arkadievna; Hardin, Ernest

2015-11-01

This study identified potential geologic repository concepts for disposal of spent nuclear fuel (SNF) and (2) evaluated the achievable repository waste emplacement rate and the time required to complete the disposal for these concepts. Total repository capacity is assumed to be approximately 140,000 MT of spent fuel. The results of this study provide an important input for the rough-order-of-magnitude (ROM) disposal cost analysis. The disposal concepts cover three major categories of host geologic media: crystalline or hard rock, salt, and argillaceous rock. Four waste package sizes are considered: 4PWR/9BWR; 12PWR/21BWR; 21PWR/44BWR, and dual purpose canisters (DPCs). The DPC concepts assume that the existing canisters will be sealed into disposal overpacks for direct disposal. Each concept assumes one of the following emplacement power limits for either emplacement or repository closure: 1.7 kW; 2.2 kW; 5.5 kW; 10 kW; 11.5 kW, and 18 kW.

Logistics Modeling of Emplacement Rate and Duration of Operations for Generic Geologic Repository Concepts

International Nuclear Information System (INIS)

Kalinina, Elena Arkadievna; Hardin, Ernest

2015-01-01

This study identified potential geologic repository concepts for disposal of spent nuclear fuel (SNF) and (2) evaluated the achievable repository waste emplacement rate and the time required to complete the disposal for these concepts. Total repository capacity is assumed to be approximately 140,000 MT of spent fuel. The results of this study provide an important input for the rough-order-of-magnitude (ROM) disposal cost analysis. The disposal concepts cover three major categories of host geologic media: crystalline or hard rock, salt, and argillaceous rock. Four waste package sizes are considered: 4PWR/9BWR; 12PWR/21BWR; 21PWR/44BWR, and dual purpose canisters (DPCs). The DPC concepts assume that the existing canisters will be sealed into disposal overpacks for direct disposal. Each concept assumes one of the following emplacement power limits for either emplacement or repository closure: 1.7 kW; 2.2 kW; 5.5 kW; 10 kW; 11.5 kW, and 18 kW.

Impact of cementitious materials decalcification on transfer properties: application to radioactive waste deep repository

International Nuclear Information System (INIS)

Perlot, C.

2005-09-01

Cementitious materials have been selected to compose the engineering barrier system (EBS) of the French radioactive waste deep repository, because of concrete physico-chemical properties: the hydrates of the cementitious matrix and the pH of the pore solution contribute to radionuclides retention; furthermore the compactness of these materials limits elements transport. The confinement capacity of the system has to be assessed while a period at least equivalent to waste activity (up to 100.000 years). His durability was sustained by the evolution of transfer properties in accordance with cementitious materials decalcification, alteration that expresses structure long-term behavior. Then, two degradation modes were carried out, taking into account the different physical and chemical solicitations imposed by the host formation. The first mode, a static one, was an accelerated decalcification test using nitrate ammonium solution. It replicates the EBS alteration dues to underground water. Degradation kinetic was estimated by the amount of calcium leached and the measurement of the calcium hydroxide dissolution front. To evaluate the decalcification impact, samples were characterized before and after degradation in term of microstructure (porosity, pores size distribution) and of transfer properties (diffusivity, gas and water permeability). The influence of cement nature (ordinary Portland cement, blended cement) and aggregates type (lime or siliceous) was observed: experiments were repeated on different mortars mixes. On this occasion, an essential reflection on this test metrology was led. The second mode, a dynamical degradation, was performed with an environmental permeameter. It recreates the EBS solicitations ensured during the re-saturation period, distinguished by the hydraulic pressure imposed by the geologic layer and the waste exothermicity. This apparatus, based on triaxial cell functioning, allows applying on samples pressure drop between 2 and 10 MPa and

Databases, institutional repositories and an organisational work flow

CSIR Research Space (South Africa)

Van der Merwe, Adèle

2008-06-01

Full Text Available . In addition, existing open source repository software lacks high level internal quality controls. In an attempt to address compliance, selection and quality control issues, a workflow system was developed for the TOdB system that also impacts...

[Self-archiving of biomedical papers in open access repositories].

Science.gov (United States)

Abad-García, M Francisca; Melero, Remedios; Abadal, Ernest; González-Teruel, Aurora

2010-04-01

Open-access literature is digital, online, free of charge, and free of most copyright and licensing restrictions. Self-archiving or deposit of scholarly outputs in institutional repositories (open-access green route) is increasingly present in the activities of the scientific community. Besides the benefits of open access for visibility and dissemination of science, it is increasingly more often required by funding agencies to deposit papers and any other type of documents in repositories. In the biomedical environment this is even more relevant by the impact scientific literature can have on public health. However, to make self-archiving feasible, authors should be aware of its meaning and the terms in which they are allowed to archive their works. In that sense, there are some tools like Sherpa/RoMEO or DULCINEA (both directories of copyright licences of scientific journals at different levels) to find out what rights are retained by authors when they publish a paper and if they allow to implement self-archiving. PubMed Central and its British and Canadian counterparts are the main thematic repositories for biomedical fields. In our country there is none of similar nature, but most of the universities and CSIC, have already created their own institutional repositories. The increase in visibility of research results and their impact on a greater and earlier citation is one of the most frequently advance of open access, but removal of economic barriers to access to information is also a benefit to break borders between groups.

An Optimal Centralized Carbon Dioxide Repository for Florida, USA

Directory of Open Access Journals (Sweden)

Brandon Poiencot

2011-03-01

Full Text Available For over a decade, the United States Department of Energy, and engineers, geologists, and scientists from all over the world have investigated the potential for reducing atmospheric carbon emissions through carbon sequestration. Numerous reports exist analyzing the potential for sequestering carbon dioxide at various sites around the globe, but none have identified the potential for a statewide system in Florida, USA. In 2005, 83% of Florida’s electrical energy was produced by natural gas, coal, or oil (e.g., fossil fuels, from power plants spread across the state. In addition, only limited research has been completed on evaluating optimal pipeline transportation networks to centralized carbon dioxide repositories. This paper describes the feasibility and preliminary locations for an optimal centralized Florida-wide carbon sequestration repository. Linear programming optimization modeling is used to plan and route an idealized pipeline network to existing Florida power plants. Further analysis of the subsurface geology in these general locations will provide insight into the suitability of the subsurface conditions and the available capacity for carbon sequestration at selected possible repository sites. The identification of the most favorable site(s is also presented.

Modeling and Analysis on Radiological Safety Assessment of Low- and Intermediate Level Radioactive Waste Repository

Energy Technology Data Exchange (ETDEWEB)

Lee, Youn Myoung; Jung, Jong Tae; Kang, Chul Hyung (and others)

2008-04-15

Modeling study and analysis for technical support for the safety and performance assessment of the low- and intermediate level (LILW) repository partially needed for radiological environmental impact reporting which is essential for the licenses for construction and operation of LILW has been fulfilled. Throughout this study such essential area for technical support for safety and performance assessment of the LILW repository and its licensing as gas generation and migration in and around the repository, risk analysis and environmental impact during transportation of LILW, biosphere modeling and assessment for the flux-to-dose conversion factors for human exposure as well as regional and global groundwater modeling and analysis has been carried out.

Modeling and Analysis on Radiological Safety Assessment of Low- and Intermediate Level Radioactive Waste Repository

International Nuclear Information System (INIS)

Lee, Youn Myoung; Jung, Jong Tae; Kang, Chul Hyung

2008-04-01

Modeling study and analysis for technical support for the safety and performance assessment of the low- and intermediate level (LILW) repository partially needed for radiological environmental impact reporting which is essential for the licenses for construction and operation of LILW has been fulfilled. Throughout this study such essential area for technical support for safety and performance assessment of the LILW repository and its licensing as gas generation and migration in and around the repository, risk analysis and environmental impact during transportation of LILW, biosphere modeling and assessment for the flux-to-dose conversion factors for human exposure as well as regional and global groundwater modeling and analysis has been carried out

Repositories; Repositorios

Energy Technology Data Exchange (ETDEWEB)

Freire, Carolina Braccini; Tello, Cledola Cassia Oliveira de [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil)]. E-mails: cbf@cdtn.br; tellocc@cdtn.br

2007-11-15

The use of the nuclear energy is increasing in all areas. Then the radioactive waste management is in continuous development to comply the national and international established requirements. The final objective is to assure that it will not have any contamination of the public or the environmental, and that the exposition doses will be lower than the radiological protection limits. The multi barrier concept for the repository is internationally recognized. Among the repository types, the most used are: near surface, geological formations and of deposition in rock cavities. This article explains the concept and the types of repository and gives some examples of them. (author)

Building Connections, Collections, and Communities: Increasing the Visibility and Impact of Extension through Institutional Repositories

Science.gov (United States)

Inefuku, Harrison W.; Franz, Nancy K.

2015-01-01

Over the past 20 years, university libraries have developed and manage institutional repositories--digital libraries that provide free, public access to the research, scholarship, and publications of their university's faculty, staff, and students. Although underused by Extension professionals, institutional repositories are powerful tools that…

Twenty years' experience with shallow ground repositories in India

International Nuclear Information System (INIS)

Balu, K.; Mohan, A.L.; Narayan, P.K.; Godse, V.B.; Sunder Rajan, N.S.

1984-01-01

With the setting up of the Bhabha Atomic Research Centre at Trombay, the first nuclear research centre in India, more than two decades ago, the need arose for disposal of the country's low-level radioactive solid wastes. Since then, nuclear power stations and other nuclear installations have been set up in different locations and the major mode of disposal for low-level solid wastes has been in engineered facilities in shallow land. The paper presents an overview of the Indian experience, with shallow land repositories for low-active solid wastes, from the point of view of design, operation and surveillance, at a number of sites. The influence of site characteristics on the design of the repository and the underground disposal modules is discussed. Details of the pre-operational investigations performed at different sites and the scheme for monitoring and surveillance of operating repositories are also included. The paper also presents briefly the type of safety analysis being carried out to evaluate possible environmental impact due to the operation of the shallow land repositories. (author)

Audit and Certification Process for Science Data Digital Repositories

Science.gov (United States)

Hughes, J. S.; Giaretta, D.; Ambacher, B.; Ashley, K.; Conrad, M.; Downs, R. R.; Garrett, J.; Guercio, M.; Lambert, S.; Longstreth, T.; Sawyer, D. M.; Sierman, B.; Tibbo, H.; Waltz, M.

2011-12-01

Science data digital repositories are entrusted to ensure that a science community's data are available and useful to users both today and in the future. Part of the challenge in meeting this responsibility is identifying the standards, policies and procedures required to accomplish effective data preservation. Subsequently a repository should be evaluated on whether or not they are effective in their data preservation efforts. This poster will outline the process by which digital repositories are being formally evaluated in terms of their ability to preserve the digitally encoded information with which they have been entrusted. The ISO standards on which this is based will be identified and the relationship of these standards to the Open Archive Information System (OAIS) reference model will be shown. Six test audits have been conducted with three repositories in Europe and three in the USA. Some of the major lessons learned from these test audits will be briefly described. An assessment of the possible impact of this type of audit and certification on the practice of preserving digital information will also be provided.

Appraisal of hard rock for potential underground repositories of radioactive wastes

International Nuclear Information System (INIS)

Cook, N.G.W.

1977-10-01

The mechanical safety and stability of such an underground repository depends largely on the virgin state of stress in the rock, groundwater pressures, the strengths of the rocks, heating by the decay of the radioactive wastes, and the layout of the excavations and the disposition of waste cannisters within them. A large body of pertinent data exists in the literature, and each of these factors has been analyzed in the light of this information. The results indicate that there are no fundamental geological nor mechanical reasons why repositories capable of storing radioactive wastes should not be excavated at suitable sites in hard rock. However, specific tests to determine the mechanical and thermal properties of the rocks at a site would be needed to provide the data for the engineering design of a repository. Also, little experience exists of the effects on underground excavations of thermal loads, so that this aspect requires theoretical study and experimental validation. The depths of these potential repositories would lie in the range from 0.5 to 2.0 km below surface, depending upon the strength of the rock. Virgin states of stress have been measured at such depths which would retard the ingress of groundwater and obviate the incidence of faulting. A typical repository comprising three horizons each with a total area of 5 km 2 would have the capacity to store wastes with thermal output of 240 MW

The radiation resistance and cobalt biosorption activity of yeast strains isolated from the Lanyu low-level radioactive waste repository in Taiwan.

Science.gov (United States)

Li, Chia-Chin; Chung, Hsiao-Ping; Wen, Hsiao-Wei; Chang, Ching-Tu; Wang, Ya-Ting; Chou, Fong-In

2015-08-01

The ubiquitous nature of microbes has made them the pioneers in radionuclides adsorption and transport. In this study, the radiation resistance and nuclide biosorption capacity of microbes isolated from the Lanyu low-level radioactive waste (LLRW) repository in Taiwan was assessed, the evaluation of the possibility of using the isolated strain as biosorbents for (60)Co and Co (II) from contaminated aqueous solution and the potential impact on radionuclides release. The microbial content of solidified waste and broken fragments of containers at the Lanyu LLRW repository reached 10(5) CFU/g. Two yeast strains, Candida guilliermondii (CT1) and Rhodotorula calyptogenae (RT1) were isolated. The radiation dose necessary to reduce the microbial count by one log cycle of CT1 and RT1 was 2.1 and 0.8 kGy, respectively. Both CT1 and RT1 can grow under a radiation field with dose rate of 6.8 Gy/h, about 100 times higher than that on the surface of the LLRW container in Lanyu repository. CT1 and RT1 had the maximum (60)Co biosorption efficiency of 99.7 ± 0.1% and 98.3 ± 0.2%, respectively in (60)Co aqueous solution (700 Bq/mL), and the (60)Co could stably retained for more than 30 days in CT 1. Nearly all of the Co was absorbed and reached equilibrium within 1 h by CT1 and RT1 in the 10 μg/g Co (II) aqueous solution. Biosorption efficiency test showed almost all of the Co (II) was adsorbed by CT1 in 20 μg/g Co (II) aqueous solution, the efficiency of biosorption by RT1 in 10 μg/g of Co (II) was lower. The maximum Co (II) sorption capacity of CT1 and RT1 was 5324.0 ± 349.0 μg/g (dry wt) and 3737.6 ± 86.5 μg/g (dry wt), respectively, in the 20 μg/g Co (II) aqueous solution. Experimental results show that microbial activity was high in the Lanyu LLRW repository in Taiwan. Two isolated yeast strains, CT1 and RT1 have high potential for use as biosorbents for (60)Co and Co (II) from contaminated aqueous solution, on the other hand, but may have the

Status of LANL investigations of temperature constraints on clay in repository environments

International Nuclear Information System (INIS)

Caporuscio, Florie A.; Cheshire, Michael C.; Newell, Dennis L.; McCarney, Mary Kate

2012-01-01

The Used Fuel Disposition (UFD) Campaign is presently evaluating various generic options for disposal of used fuel. The focus of this experimental work is to characterize and bound Engineered Barrier Systems (EBS) conditions in high heat load repositories. The UFD now has the ability to evaluate multiple EBS materials, waste containers, and rock types at higher heat loads and pressures (including deep boreholes). The geologic conditions now available to the U.S.A. and the international community for repositories include saturated and reduced water conditions, along with higher pressure and temperature (P, T) regimes. Chemical and structural changes to the clays, in either backfill/buffer or clay-rich host rock, may have significant effects on repository evolution. Reduction of smectite expansion capacity and rehydration potential due to heating could affect the isolation provided by EBS. Processes such as cementation by silica precipitation and authigenic illite could change the hydraulic and mechanical properties of clay-rich materials. Experimental studies of these repository conditions at high P,T have not been performed in the U.S. for decades and little has been done by the international community at high P,T. The experiments to be performed by LANL will focus on the importance of repository chemical and mineralogical conditions at elevated P,T conditions. This will provide input to the assessment of scientific basis for elevating the temperature limits in clay barriers.

Managing and Evaluating Digital Repositories

Science.gov (United States)

Zuccala, Alesia; Oppenheim, Charles; Dhiensa, Rajveen

2008-01-01

Introduction: We examine the role of the digital repository manager, discuss the future of repository management and evaluation and suggest that library and information science schools develop new repository management curricula. Method: Face-to-face interviews were carried out with managers of five different types of repositories and a Web-based…

Repository simulation tests

International Nuclear Information System (INIS)

Wicks, G.G.; Bibler, N.E.; Jantzen, C.M.; Plodinec, M.J.

1984-01-01

The repository simulation experiments described in this paper are designed to assess the performance of SRP waste glass under the most realistic repository conditions that can be obtained in the laboratory. These tests simulate the repository environment as closely as possible and introduce systematically the variability of the geology, groundwater chemistry, and waste package components during the leaching of the waste glass. The tests evaluate waste form performance under site-specific conditions, which differ for each of the geologic repositories under consideration. Data from these experiments will aid in the development of a realistic source term that can describe the release of radionuclides from SRP waste glass as a component of proposed waste packages. Hence, this information can be useful to optimize waste package design for SRP waste glass and to provide data for predicting long-term performance and subsequent conformance to regulations. The repository simulation tests also help to bridge the gap in interpreting results derived from tests performed under the control of the laboratory to the uncertainity and variability of field tests. In these experiments, site-specific repository components and conditions are emphasized and only the site specific materials contact the waste forms. An important feature of these tests is that both actual and simulated waste glasses are tested identically. 7 figures, 2 tables

A Summary of Properties Used to Evaluate INEEL Calcine Disposal in the Yucca Mountain Repository

International Nuclear Information System (INIS)

Dahl, C.A.

2003-01-01

To support evaluations of the direct disposal of Idaho National Engineering and Environmental Laboratory calcines to the repository at Yucca Mountain, an evaluation of the performance of the calcine in the repository environment must be performed. This type of evaluation demonstrates, through computer modeling and analysis, the impact the calcine would have on the ability of the repository to perform its function of containment of materials during the repository lifetime. This report discusses parameters that were used in the scoping evaluation conducted in FY 2003. It provides nominal values for the parameters, with explanation of the source of the values, and how the values were modified for use in repository analysis activities

Radiological Protection Criteria for the Safety of LILW Repository in Croatia

International Nuclear Information System (INIS)

Levanat, I.; Lokner, V.; Subasic, D.

2000-01-01

Preparations for a LILW repository development in Croatia, conducted by APO Hazardous Waste Management Agency, have reached a point where the first safety assessment of the prospective facility is being attempted. For evaluation of the calculated radiological impact in the assessed option of repository development, a set of radiological protection criteria should be included in the definition of the assessment context. The Croatian regulations do not explicitly require that the repository development be supported by such safety assessment process, and do not provide a specific set of radiological criteria intended for the repository assessment which would be suitable for the constrained optimization of protection. For the initial safety assessment iterations of the prospective repository, which will address long term performance of the facility for various design and other safety options, we propose to use relatively simple radiological protection criteria, consisting only of individual dose and risk constraints for the general population. The numerical values for these constraints are established in accordance with the recognized international recommendations and in compliance with all possibly relevant Croatian safety requirements. (author)

The repository ecology an approach to understanding repository and service interactions

CERN Document Server

CERN. Geneva; Hagemann, Melissa

2007-01-01

An increasing number of university institutions and other organisations are deciding to deploy repositories and a growing number of formal and informal distributed services are supporting or capitalising on the information these repositories provide. Despite reasonably well understood technical architectures, early majority adopters may struggle to articulate their place within the actualities of a wider information environment. The idea of a repository ecology provides developers and administrators with a useful way of articulating and analysing their place in the information environment, and the technical and organisational interactions they have, or are developing, with other parts of such an environment. This presentation will provide an overview of the concept of a repository ecology and examine some examples from the domains of scholarly communications and elearning.

Deep repository for spent nuclear fuel. SR 97 - Post-closure safety. Main Report. Summary

International Nuclear Information System (INIS)

Hedin, A.

1999-11-01

and biosphere are analyzed in the canister defect scenario. Releases from the geosphere are converted to doses in different ecosystems. The variation in flow-related data in the geosphere has the greatest impact on the result, followed by data uncertainties for the biosphere. Other conclusions are that our understanding of fuel dissolution needs to be improved, and that the probability and size of initial canister defects that escape quality-control inspection is difficult to estimate. Risk analyses in the form of simplified probabilistic calculations are also performed. The risk analyses show that all sites lie well below the acceptance criterion. The maximum risk for release to a well is never more than 0.5 percent of the acceptance criterion, even when the calculations are extended a million years into the future. The same applies to releases to peat land for times up to 100,000 years, while the maximum risk here grows to about one-tenth of the acceptance criterion at the least favourable site at times after 100,000 years. The consequences of future climate change are explored in the climate scenario. A conceivable sequence of events, including severe glaciation, on each of the three sites is sketched for the coming 150,000 years. In the climate scenario as well, the overall conclusion is that the isolating capacity of the copper canister is not threatened by either mechanical or chemical stresses. As far as the retarding capacity of the repository is concerned, for example in the event of initial canister damage, the most important changes take place in the biosphere. The repository sites are expected to be covered by ice sheets or sea during long periods, and the aggregate effect of climate change will therefore be a reduction of the dose consequences compared with a situation where the present-day climate persists. In the earthquake scenario, the consequences of earthquakes are analyzed by means of model studies where site-specific data are used for the

Assessment of potential perturbations to Posiva's SF repository at Olkiluoto from the ONKALO Facility

International Nuclear Information System (INIS)

Alexander, W.R.; Neall, F.B.

2007-06-01

Although the site of the proposed spent fuel repository at Olkiluoto in southwest Finland has been extensively investigated over the last fifteen years, Posiva decided to construct a rock characterisation facility (RCF) at the site to collect more detailed information on the host rock. The data provided by the ONKALO RCF will support the detailed repository design and safety assessment (SA) and will allow construction and disposal methods to be tested under relevant in situ conditions. ONKALO has been so designed that it can act as access routes and auxiliary rooms for the SF repository and so may be in use for the entire operational phase of the repository (currently up to 100 years). Extensive experience from deep mining suggests that such an extended period of operation could have a major impact on both the host rock formation and any nearby facilities, such as the SF repository, and, consequently, Posiva decided to investigate potential perturbations to the repository caused by the existence of ONKALO. A preliminary assessment was carried out in 2003, before construction of the RCF began, and this was recently partially updated in early 2006. This current report represents the most recent update of these reports and has the primary aims of: checking if the previous reports have missed any essential issues; evaluating whether the identified issues have been treated in an appropriate manner; updating the reports in the light of new information. This is carried out based on data from ONKALO itself and on improved understanding of some of the perturbation mechanisms identified in the original studies along with a consideration of newly identified processes. This report differs from the previous studies in addressing the issues in a more SA-oriented manner (for example, focussing the examination of potential perturbations on a re-worked FEP list), allowing the work reported here to be more easily dovetailed with future SA studies on the Olkiluoto repository

Biogeochemistry of Redox at Repository Depth and Implications for the Canister

Energy Technology Data Exchange (ETDEWEB)

Bath, Adrian; Hermansson, Hans-Peter

2009-08-15

The present groundwater chemical conditions at the candidate sites for a spent nuclear fuel repository in Sweden (the Forsmark and Laxemar sites) and processes affecting its future evolution comprise essential conditions for the evaluation of barrier performance and long-term safety. This report reviews available chemical sampling information from the site investigations at the candidate sites, with a particular emphasis on redox active groundwater components and microbial populations that influence redox affecting components. Corrosion of copper canister material is the main barrier performance influence of redox conditions that is elaborated in the report. One section addresses native copper as a reasonable analogue for canister materials and another addresses the feasibility of methane hydrate ice accumulation during permafrost conditions. Such an accumulation could increase organic carbon availability in scenarios involving microbial sulphate reduction. The purpose of the project is to evaluate and describe the available knowledge and data for interpretation of geochemistry, microbiology and corrosion in safety assessment. A conclusive assessment of the sufficiency of information can, however, only be done in the future context of a full safety assessment. The authors conclude that SKB's data and models for chemical and microbial processes are adequate and reasonably coherent. The redox conditions in the repository horizon are predominantly established through the SO{sub 4}2-/HS- and Fe3+/Fe2+ redox couples. The former may exhibit a more significant buffering effect as suggested by measured Eh values, while the latter is associated with a lager capacity due to abundant Fe(II) minerals in the bedrock. Among a large numbers of groundwater features considered in geochemical equilibrium modelling, Eh, pH, temperature and concentration of dissolved sulphide comprise the most essential canister corrosion influences. Groundwater sulphide may originate from

Biogeochemistry of Redox at Repository Depth and Implications for the Canister

International Nuclear Information System (INIS)

Bath, Adrian; Hermansson, Hans-Peter

2009-08-01

The present groundwater chemical conditions at the candidate sites for a spent nuclear fuel repository in Sweden (the Forsmark and Laxemar sites) and processes affecting its future evolution comprise essential conditions for the evaluation of barrier performance and long-term safety. This report reviews available chemical sampling information from the site investigations at the candidate sites, with a particular emphasis on redox active groundwater components and microbial populations that influence redox affecting components. Corrosion of copper canister material is the main barrier performance influence of redox conditions that is elaborated in the report. One section addresses native copper as a reasonable analogue for canister materials and another addresses the feasibility of methane hydrate ice accumulation during permafrost conditions. Such an accumulation could increase organic carbon availability in scenarios involving microbial sulphate reduction. The purpose of the project is to evaluate and describe the available knowledge and data for interpretation of geochemistry, microbiology and corrosion in safety assessment. A conclusive assessment of the sufficiency of information can, however, only be done in the future context of a full safety assessment. The authors conclude that SKB's data and models for chemical and microbial processes are adequate and reasonably coherent. The redox conditions in the repository horizon are predominantly established through the SO 4 2- /HS - and Fe 3+ /Fe 2+ redox couples. The former may exhibit a more significant buffering effect as suggested by measured Eh values, while the latter is associated with a lager capacity due to abundant Fe(II) minerals in the bedrock. Among a large numbers of groundwater features considered in geochemical equilibrium modelling, Eh, pH, temperature and concentration of dissolved sulphide comprise the most essential canister corrosion influences. Groundwater sulphide may originate from sulphide

The impact of repository heat on thermo-hydrological performance at Yucca Mountain

International Nuclear Information System (INIS)

Buscheck, T.A.; Nitao, J.J.

1993-09-01

To safely and permanently store high-level nuclear waste, the potential Yucca Mountain repository site must mitigate the release and transport of radionuclides for tens of thousands of years. In the failure scenario of greatest concern, water would contact a waste package (WP), accelerate its failure rate, and eventually transport radionuclides to the water table. These analyses have demonstrated that the only significant source of liquid water is nonequilibrium fracture flow from: (1) meteoric sources, (2) condensate drainage generated under boiling conditions, and (3) condensate drainage generated under sub-boiling conditions. The first source of liquid water arises from the ambient system; the second and third sources are generated by repository heat. Buoyant vapor flow, occurring either on a sub-repository scale or on a mountain scale, may play an important role in the generation of the second and third sources of liquid water. By considering a wide range in bulk permeability, k b , the authors identify the threshold k b (called k b hyd ) at which buoyant, vapor convection begins to dominate hydrological behavior, and the threshold k b (called k b th ) at which this convection begins to dominate thermal behavior. They find that k b th is generally an order of magnitude larger than k b hyd and that the development of a large above-boiling zone suppresses the effects of buoyant vapor flow. Of particular concern are conditions that promote the focusing of vapor flow and condensate drainage, which could result in persistent two-phase conditions (often referred to as the heat-pipe effect) in the vicinity of WPs. The results of this study underscore the need for in situ heater tests to help diagnose the potential for the major repository-heat-driven sources of fracture flow

Life cycle assessment of geological repositories for the final disposal of spent fuel in Finland and Sweden

International Nuclear Information System (INIS)

Puhrer, A.; Bauer, C.

2014-01-01

This paper presents a Life Cycle Assessment (LCA) of the geological repositories for the final disposal of spent nuclear fuel in Finland and Sweden. A separate LCA has been performed for the geological spent fuel repository in each country and the results have been compared. A further benchmark comparison has been made with the LCA of the Swiss geological repository for high-level waste and spent fuel. The life cycle inventory (LCI) product system boundaries include the spent fuel repository and encapsulation facility in each country. All materials, processes, consumed utilities and transport associated with the construction, operation and closure of the repositories for spent fuel are included in the LCI. The life cycle impact assessment (LCIA) is performed using two methods: IPCC 2007 Climate Change and ReCiPe. These assessment methods return results pertaining to global warming potential (GWP) as well as a number of environmental impact categories such as human toxicity and natural land transformation. Results indicate that the use of copper for disposal canister fabrication and bentonite for repository backfilling are the causes for most of the environmental impact of the spent fuel repositories in Finland and Sweden. Alternate, less bentonite-intensive backfilling scenarios may mitigate this impact. While the Swiss bentonite consumption is lower and no copper is used for canister fabrication, the Swiss electricity and fuel consumption associated with final disposal of high-level waste and spent fuel is significantly higher than in Finland or Sweden. Approximately 1 g CO 2 -eq is emitted due to the final disposal of spent fuel and HLW per kWh of nuclear generated electricity. This represents some 10% of the emissions due to the entire nuclear energy chain and is practically negligible in the context of GHG emissions of other energy technologies. (authors)

Reactive transport predictions for an Olkiluoto. Final repository tunnel unit

International Nuclear Information System (INIS)

Luukkonen, A.; Nordman, H.

2007-09-01

The presented hydrogeochemical reactive transport calculations concentrate to a defined unit piece (unit cell) of the planned Olkiluoto repository that is under design for spent nuclear fuel. The material properties assigned to the tunnel unit are based on literature as far as possible. Calculations make up geochemical future scenarios on the repository evolution. Most recent predictions on the potential future climate at Olkiluoto are utilised together with estimates how future hydraulic conditions affect the repository. Two climate scenarios are considered in detail. The Weichselian-R scenario is based on the repetition of the last glacial cycle, while the Emissions-M scenario attempts to predict the future groundwater conditions at Olkiluoto in the situation where the atmospheric greenhouse gasses delay the next glacial cycle at least for 100,000 years. The groundwater compositions, considered active at the repository depth in future, are judged in this study. Several geochemical processes are considered active at the repository depth. Calculations concentrate on the changes occurring with time within the tunnel unit. All simulations are done in geochemically reducing conditions. It turns out that sulphur cycling in these conditions is in central role considering the safety assessment studies of Olkiluoto repository. Furthermore, groundwater salinity and cation occupancy within the exchange sites of montmorillonite contributes to sealing properties of the engineered barrier system. Calculations attempt to estimate effects of possible future scenarios for the Olkiluoto repository. The results indicate that the buffer capacities assigned to the tunnel unit are large enough, at least to next 100,000 years, to maintain dissolved sulphide contents low in the groundwater infiltrating through the tunnel engineered barrier system. Geochemical reactions raise the bicarbonate levels within the groundwater. This is a useful buffer if low pH conditions emerge in the

Development of a central final repository management for the coordination of the waste for Schacht Konrad from public authorities

International Nuclear Information System (INIS)

Graffunder, Iris; Dominke-Bendix, Carola; Waldek, Achim

2012-01-01

The central final repository management is supposed to fulfill the following tasks: active collaboration of Konrad contract draft, signing of internal contracts and agreements, cooperation contract with GNS, cooperation with coordination authorities, inventory taking of wastes (existing inventory and prognosis) and interim storage capacities of public authorities, development of planning and management software, optimization of the final repository documentation, container management, logistics concept, long-term disposal planning and prognosis, planning and coordination of the annual waste amount, management and documentation of disposed waste allocation, coordination of transport schedules, consulting service for waste obligations (final repository requirements, product control, documentation).

Elaboration of protocol for characterization of clay as a filling material and coverage for surface repository

International Nuclear Information System (INIS)

Santos, Daisy Mary Marchezini dos

2017-01-01

The nuclear energy in its various applications generates wastes that must be properly treated. The Radioactive Waste Management covers operations since generation of the waste until to its storage in repository ensuring the protection of man and of environment of the possible negative impacts. The radioactive waste are segregated, treated, conditioned in suitable packaging and posteriorly are stored or disposal in repository. The “RBMN Project” is a priority project of CNEN to implementation the repository for the deposition of low and intermediate level radioactive waste generated by nuclear energy activities in Brazil, proposing a definitive solution for its storage. Engineered and natural barriers as the filling layer and coverage layer will compose the disposal system of a near surface repository, concept proposed by the “RBMN Project”. The use these barriers views to avoid or restrict the release of radionuclides present in waste for the humans beings and environment. The waterproofing barriers are composed of clays. Certainly, for the national repository, will be used those clays existing in the place where it will be implanted it. So some fundamentals tests will have to be carried for to verify the suitability of these clays as barriers. These tests were determined and realized with a reference clay, a brazilian bentonite constituted of 67.2% montmorillonite. The results were compared with national and international literature of materials with similar mineralogical features. The values found with 95% reliance were 9.73±0,35 μm for granulometric size. For the moisture content were 13,3±0,6% and for capacity of cationic exchange were , 816±9 mmol.kg"-"1. For the hydraulic conductivity, without the use of internal pressure, it was obtained maximum value of 59.0% saturated. In addition, during the observed period, there was no percolation in the test specimen submitted to internal pressure of 200 kPa. This result leads to the conclusion that the

The repository ecology: an approach to understanding repository and service interactions

CERN Multimedia

CERN. Geneva

2007-01-01

An increasing number of university institutions and other organisations are deciding to deploy repositories and a growing number of formal and informal distributed services are supporting or capitalising on the information these repositories provide. Despite reasonably well understood technical architectures, early majority adopters may struggle to articulate their place within the actualities of a wider information environment. The idea of a repository ecology provides developers and administrators with a useful way of articulating and analysing their place in the information environment, and the technical and organisational interactions they have, or are developing, with other parts of such an environment. This presentation will provide an overview of the concept of a repository ecology and examine some examples from the domains of scholarly communications and elearning. View John Robertson's biography

Natural sorbents as barriers against migration of radionuclides from radioactive waste repositories

International Nuclear Information System (INIS)

Stefanova, I.; Gradev, G.D.

1993-01-01

The sorption properties of Bulgarian inorganic sorbents - clinoptilolite, vermiculite, bentonite, glauconite, celadonite and loess, which can be used as buffer, backfill and sealing materials in radwaste repository are studied. Experimental data about sorption and desorption capacities, radiation and thermal stability of sorbents from different Bulgarian deposits are reported and compared. Clinoptilolite from Beli Plast and its sodium variety from Kostino and Moryantsi is recommended as a barrier against radionuclide migration from radwaste repository due to their high sorption capacity of 137 Ce, 90 Sr and 60 Co. The high selectivity of vermiculite for polyvalent ions ( 144 Ce, 59 Fe and 90 Sr) gives grounds to include the sorption on vermiculite as a second step in the ion exchange technology for low level laundry waste decontamination. Bentonite is studied as a proposed buffer, backfill and sealing material. Its selectivity for cesium is lower compared to those of clinoptilolite. Thus a tailored-made mixture of bentonite and clinoptilolite will act as a barrier against radionuclides in different oxidation state. Glauconite can be successfully used as a barrier against migration of 144 Ce, 90 Sr, 54 Mn and 65 Zn. Loess is also included in the study, as the Kozloduy NPP is sited on loess formation and it is a natural potential site for low and intermediate level waste burial. It is concludes that zeolites and clays of Bulgarian deposits can be used effectively against radionuclide migration from radioactive waste repositories. 59 refs., 5 tabs. (author)

Long-Term Safety Analysis of Baldone Radioactive Waste Repository and Updating of Waste Acceptance Criteria

International Nuclear Information System (INIS)

2001-12-01

The main objective of the project was to provide advice to the Latvian authorities on the safety enhancements and waste acceptance criteria for near surface radioactive waste disposal facilities of the Baldone repository. The project included the following main activities: Analysis of the current status of the management of radioactive waste in Latvia in general and, at the Baldone repository in particular Development of the short and long-term safety analysis of the Baldone repository, including: the planned increasing of capacity for disposal and long term storage, the radiological analysis for the post-closure period Development of the Environment Impact Statement, for the new foreseen installations, considering the non radiological components Proposal of recommendations for future updating of radioactive waste acceptance criteria Proposal of recommendations for safety upgrades to the facility. The work programme has been developed in phases and main tasks as follows. Phase 0: Project inception, Phase 1: Establishment of current status, plans and practices (Legislation, regulation and standards, Radioactive waste management, Waste acceptance criteria), Phase 2: Development of future strategies for long-term safety management and recommendations for safety enhancements. The project team found the general approach use at the installation, the basic design and the operating practices appropriate to international standards. Nevertheless, a number of items subject to potential improvements were also identified. These upgrading recommendations deal with general aspects of the management (mainly storage versus disposal of long-lived sources), site and environmental surveillance, packaging (qualification of containers, waste characterization requirements), the design of an engineered cap and strategies for capping. (author)

Some reflections on human intrusion into a nuclear waste repository

International Nuclear Information System (INIS)

Westerlind, M.

2002-01-01

This paper summarises some of the Swedish nuclear regulators' requirements and views related to intrusion into a repository for spent nuclear fuel, in the post-closure phase. The focus is however on experiences from the interaction with various stakeholders in the Swedish process for siting a repository. It is recognised that intrusion is not a major concern but that it is regularly raised in the debate, often in connection with issues related to retrievability. It is pointed out that more attention should be paid to the repository performance after an intrusion event, both in safety assessments and in communication with stakeholders, and not only address the immediate impacts to intruders. It is believed that international co-operation would be useful for developing methodologies for defining intrusion scenarios. (author)

Bentonite as a backfill material for shallow land repositories

International Nuclear Information System (INIS)

Yalmali, V.S.; Deshingkar, D.S.

2001-01-01

Two commercially available indigenous bentonite samples were evaluated for their cesium and strontium sorption properties in distilled water and surface water. By converting them into sodium form, the distribution coefficients for both cesium (I) and strontium (II) increased. Sodium bentonite was recommended because of high sorption capacity for Cs(I), Mg(II) and Sr(II) for use as backfill material in shallow land repositories where cement waste form containing Cs, Sr and Be wastes are disposed. (author)

EBS modelling for the development of repository concepts tailored to siting environments

International Nuclear Information System (INIS)

Ishiguro, K.; Ueda, H.; Wakasugi, K.; Sakabe, Y.; Kitayama, K.; Umeki, H.; Takase, H.

2007-01-01

The Japanese siting approach for a HLW repository calls for volunteer host municipalities and thereby places particular emphasis on design flexibility. In particular, the repository concept needs to be tailored to the specific site characteristics. Starting from the H12 repository concept, NUMO has been examining a range of possible repository design options, including the EBS. In this paper. the requirements and strategy for the development of models for performance assessment and process understanding are discussed, taking into account the step-wise, iterative process of developing repository concepts. The areas requiring further development of models and databases in the long-term R and D programme have been identified as a 'wish list' that relates to the evaluation of a range of potential repository concepts, focusing on the near-field for the early stages of the development process. Among the issues on the list, NUMO has started the development of a flexible computer code for modelling three-dimensional mass transport to evaluate the impacts of various design options and components of the EBS. This tool has been applied to the analysis of the barrier effects of the tunnel plugs located in fractured rock. (authors)

Basic repository environment assessment design basis, Cypress Creek Dome Site

International Nuclear Information System (INIS)

1988-03-01

This study examines the engineering factors and costs associated with the construction, operation, and decommissioning of a high-level nuclear waste repository in salt in the Gulf Interior Region at Cypress Creek Cone, Mississippi. The study assumes a repository capacity of 36,000 metric tons of heavy metal (MTHM) of unreprocessed spent fuel and 36,000 MTHM of commercial high-level reprocessing waste, along with 7020 canisters of defense high-level reprocessing waste and associated quantities of remote- and contact-handled transuranic waste (TRU). With the exception of TRU, all the waste forms are placed in 300- to 1000-year-life carbon-steel waste packages in a collocated waste handling and packaging facility (WHPF), which is also described. The construction, operation, and decommissioning of the proposed repository is estimated to cost approximately $4.66 billion. Costs include those for the collocated WHPF, engineering, and contingency, but exclude waste from assembly and shipment to the site and waste package fabrication and shipment to the site. These costs reflect the relatively easy access to the site. Construction would require an estimated 7 years. Engineering factors and costs are not strongly influenced by environmental considerations. 53 refs., 24 figs., 10 tabs

Construction of quality-assured infant feeding process of care data repositories: Construction of the perinatal repository (Part 2).

Science.gov (United States)

García-de-León-Chocano, Ricardo; Muñoz-Soler, Verónica; Sáez, Carlos; García-de-León-González, Ricardo; García-Gómez, Juan M

2016-04-01

This is the second in a series of two papers regarding the construction of data quality (DQ) assured repositories, based on population data from Electronic Health Records (EHR), for the reuse of information on infant feeding from birth until the age of two. This second paper describes the application of the computational process of constructing the first quality-assured repository for the reuse of information on infant feeding in the perinatal period, with the aim of studying relevant questions from the Baby Friendly Hospital Initiative (BFHI) and monitoring its deployment in our hospital. The construction of the repository was carried out using 13 semi-automated procedures to assess, recover or discard clinical data. The initial information consisted of perinatal forms from EHR related to 2048 births (Facts of Study, FoS) between 2009 and 2011, with a total of 433,308 observations of 223 variables. DQ was measured before and after the procedures using metrics related to eight quality dimensions: predictive value, correctness, duplication, consistency, completeness, contextualization, temporal-stability, and spatial-stability. Once the predictive variables were selected and DQ was assured, the final repository consisted of 1925 births, 107,529 observations and 73 quality-assured variables. The amount of discarded observations mainly corresponds to observations of non-predictive variables (52.90%) and the impact of the de-duplication process (20.58%) with respect to the total input data. Seven out of thirteen procedures achieved 100% of valid births, observations and variables. Moreover, 89% of births and ~98% of observations were consistent according to the experts׳ criteria. A multidisciplinary approach along with the quantification of DQ has allowed us to construct the first repository about infant feeding in the perinatal period based on EHR population data. Copyright © 2016 Elsevier Ltd. All rights reserved.

Deep repository for spent nuclear fuel. SR-97-Post-closure safety. Main Report. Volume I and II

Energy Technology Data Exchange (ETDEWEB)

Hedin, A. [ed.

1999-11-01

buffer, geosphere and biosphere are analyzed in the canister defect scenario. Releases from the geosphere are converted to doses in different ecosystems. The variation in flow-related data in the geosphere has the greatest impact on the result, followed by data uncertainties for the biosphere. Other conclusions are that our understanding of fuel dissolution needs to be improved, and that the probability and size of initial canister defects that escape quality-control inspection is difficult to estimate. Risk analyses in the form of simplified probabilistic calculations are also performed. The risk analyses show that all sites lie well below the acceptance criterion. The maximum risk for release to a well is never more than 0.5 percent of the acceptance criterion, even when the calculations are extended a million years into the future. The same applies to releases to peat land for times up to 100,000 years, while the maximum risk here grows to about one-tenth of the acceptance criterion at the least favourable site at times after 100,000 years. The consequences of future climate change are explored in the climate scenario. A conceivable sequence of events, including severe glaciation, on each of the three sites is sketched for the coming 150,000 years. In the climate scenario as well, the overall conclusion is that the isolating capacity of the copper canister is not threatened by either mechanical or chemical stresses. As far as the retarding capacity of the repository is concerned, for example in the event of initial canister damage, the most important changes take place in the biosphere. The repository sites are expected to be covered by ice sheets or sea during long periods, and the aggregate effect of climate change will therefore be a reduction of the dose consequences compared with a situation where the present-day climate persists. In the earthquake scenario, the consequences of earthquakes are analyzed by means of model studies where site-specific data are used

Deep repository for spent nuclear fuel. SR-97-Post-closure safety. Main Report. Volume I and II

Energy Technology Data Exchange (ETDEWEB)

Hedin, A [ed.

1999-11-01

, geosphere and biosphere are analyzed in the canister defect scenario. Releases from the geosphere are converted to doses in different ecosystems. The variation in flow-related data in the geosphere has the greatest impact on the result, followed by data uncertainties for the biosphere. Other conclusions are that our understanding of fuel dissolution needs to be improved, and that the probability and size of initial canister defects that escape quality-control inspection is difficult to estimate. Risk analyses in the form of simplified probabilistic calculations are also performed. The risk analyses show that all sites lie well below the acceptance criterion. The maximum risk for release to a well is never more than 0.5 percent of the acceptance criterion, even when the calculations are extended a million years into the future. The same applies to releases to peat land for times up to 100,000 years, while the maximum risk here grows to about one-tenth of the acceptance criterion at the least favourable site at times after 100,000 years. The consequences of future climate change are explored in the climate scenario. A conceivable sequence of events, including severe glaciation, on each of the three sites is sketched for the coming 150,000 years. In the climate scenario as well, the overall conclusion is that the isolating capacity of the copper canister is not threatened by either mechanical or chemical stresses. As far as the retarding capacity of the repository is concerned, for example in the event of initial canister damage, the most important changes take place in the biosphere. The repository sites are expected to be covered by ice sheets or sea during long periods, and the aggregate effect of climate change will therefore be a reduction of the dose consequences compared with a situation where the present-day climate persists. In the earthquake scenario, the consequences of earthquakes are analyzed by means of model studies where site-specific data are used for the

Basic repository environmental assessment design basis, Richton Dome site

International Nuclear Information System (INIS)

1988-01-01

This study examines the engineering factors and costs associated with the construction, operation, and decommissioning of a high-level nuclear waste repository in salt in the Gulf Interior Region at Richton Dome in Perry County, Mississippi. The study assumes a repository capacity of 36,000 metric tons of heavy metal (MTHM) of unreprocessed spent fuel and 36,000 MTHM of commercial high-level reprocessing waste, along with 7,020 canisters of defense high-level reprocessing waste and associated quantities of remote-and contact-handled transuranic waste (TRU). With the exception of TRU, all the waste forms are placed in 300- to 1,000-year-life carbon-steel waste packages in a collocated waste handling and packaging facility (WHPF), which is also described. The construction, operation, and decommissioning of the proposed repository is estimated to cost approximately $4.49 billion. Costs include those for the WHPF, engineering, and contingency, but exclude waste form assembly and shipment to the site and waste package fabrication and shipment to the site. These costs reflect the relative average wage rates of the region and the relatively easy access to the site. Construction would require an estimated 6.25 years. Engineering factors and costs are not strongly influenced by environmental considerations. 52 refs., 24 figs., 20 tabs

Basic repository environmental assessment design basis, Davis Canyon site

International Nuclear Information System (INIS)

1984-01-01

This study examines the engineering factors and costs associated with the construction, operation, and decommissioning of a high-level nuclear waste repository in salt in the Paradox Basin in Davis Canyon, Utah. The study assumes a repository capacity of 36,000 metric tons of heavy metal (MTHM) of unreprocessed spent fuel and 36,000 MTHM of commercial high-level reprocessing waste, along with 7,020 canisters of defense high-level reprocessing waste and associated quantities of remote- and contact-handled transuranic waste (TRU). With the exception of TRU, all the waste forms are placed in 300- to 1,000-year-life carbon-steel waste packages in a collected waste handling and packaging facility (WHPF), which is also described. The construction, operation, and decommissioning of the proposed repository is estimated to cost approximately $5.49 billion. Costs include those for the collocated WHPF, engineering, and contingency, but exclude waste form assembly and shipment to the site and waste package fabrication and shipment to the site. These costs reflect the relative average wage rates of the region and the relatively sound nature of the salt at this site. Construction would require an estimated 7.75 years. Engineering factors and costs are not strongly influenced by environmental considerations. 50 refs., 24 figs., 20 tabs

Basic repository environmental assessment design basis, Lavender Canyon site

International Nuclear Information System (INIS)

1988-01-01

This study examines the engineering factors and costs associated with the construction, operation, and decommissioning of a high-level nuclear waste repository in salt in the Paradox Basin in Lavender Canyon, Utah. The study assumes a repository capacity of 36,000 metric tons of heavy metal (MTHM) of unreprocessed spent fuel and 36,000 MTHM of commercial high-level reprocessing waste, along with 7020 canisters of defense high-level reprocessing waste and associated quantities of remote- and contact-handled transuranic waste (TRU). With the exception of TRU, all the waste forms are placed in 300- to 1000-year-life carbon-steel waste packages in a collocated waste handling and packaging facility (WHPF), which is also described. The construction, operation, and decommissioning of the proposed repository is estimated to cost approximately $5.51 billion. Costs include those for the collocated WHPP, engineering, and contingency, but exclude waste form assembly and shipment to the site and waste package fabrication and shipment to the site. These costs reflect the relative average wage rates of the region and the relatively sound nature of the salt at this site. Construction would require an estimated 7.75 years. Engineering factors and costs are not strongly influenced by environmental considerations. 51 refs., 24 figs., 20 tabs

Conflict, location, and politics: Siting a nuclear waste repository

International Nuclear Information System (INIS)

Jacob, G.R.

1988-01-01

Nuclear power and the management of high-level radioactive waste is examined with the goal of explaining the forces driving the formulation of the 1982 Nuclear Waste Policy Act and a subsequent decision to site a nuclear waste repository at Yucca Mountain, Nevada. The study draws upon geographic, political, economic, and organizational factors to examine the commitment to dispose of spent fuel in a geologic repository located in Nevada or in Utah, Texas, Mississippi, Louisiana, or at Hanford Washington. Special attention is given to the impact of location, science and technology on the definition of the nuclear waste problem and political agendas, public participation, and the power of the nuclear establishment. The study finds that the choice of a Yucca Mountain Nevada as the preferred site for a repository was based more on technological precedent and political-economic expediency than on the demonstrated superiority of that site's geology. Conflict over a repository location is interpreted as a symptom of more fundamental conflicts concerning: the credibility of nuclear science, the legitimacy of federal authority and administration, and the priorities of environmental protection and a nuclear economy

Autogenous healing of cracks in concrete and its relevance to radwaste repositories

International Nuclear Information System (INIS)

Guppy, R.

1988-03-01

Cracks in concrete structures within a radioactive waste repository could provide fast transport pathways and as such could impair the performance of the concrete as a barrier to radionuclide migration. It has been widely reported that cracks in concrete can heal and, therefore, the evidence in support of this phenomenon has been reviewed and its relevance to a concrete barrier in a radioactive waste repository assessed. The mechanism of crack healing is not understood, but the most likely process responsible is calcite formation under wet conditions. There is doubt concerning whether the conditions in a repository will be suitable for crack healing; especially if the cement is extensively modified with slag or fuel ash. It is concluded that further experimental work is required to assess the impact of this phenomenon on the behaviour of cracks in repositories. (author)

Report of the Task Force on the MRS/repository interface

International Nuclear Information System (INIS)

1986-02-01

In April 1985, the DOE established an MRS/repository interface task force to analyze the cost and schedule impacts of implementing an integrated waste-management system on the repository and the MRS facility. The intended end products of the study were preliminary conceptual designs of repository and MRS facilities, cost and schedule estimates, and other analyses that would advance the definition of the role and function of the MRS facility, support the preparation of the MRS proposal to Congress, and serve as a source of baseline data for further studies of the integrated waste-management system. From the general overall objectives, specific equations were developed to guide the task-force effort, e.g., What would the surface facilities at the repository look like and cost with an MRS facility in the system. In order to address these questions, five scenarios were defined and analyzed. (A number of other scenarios and associated issues were also explored to a lesser extent.) These five scenarios are as follows. Scenario 1: reference case (no MRS facility). Scenario 2: MRS facility with overpacking of both spent fuel and defense high-level waste. Scenario 3: MRS facility with overpacking of spent fuel only (defense-waste overpacking at the repository). Scenario 4: MRS facility with all overpacking at the repository. Scenario 5: MRS facility with all overpacking at the repository and western fuel shipped directly to the repository. It is apparent that, with such a limited set of scenarios, determination of the optimum system was not an objective of this study. Furthermore, time constraints limited the level of detail to which facility designs could be developed; this level can best be characterized as ''preconceptual.'' These limitations are, however, compatible with the intent of the study, which was to make general comparisons between the several systems on an internally consistent basis

Consortial routes to effective repositories

OpenAIRE

Moyle, M.; Proudfoot, R.

2009-01-01

A consortial approach to the establishment of repository services can help a group of Higher Education Institutions (HEIs) to share costs, share technology and share expertise. Consortial repository work can tap into existing structures, or it can involve new groupings of institutions with a common interest in exploring repository development. This Briefing Paper outlines some of the potential benefits of collaborative repository activity, and highlights some of the technical and organisation...

Towards Establishing an Open Access Repository of Indian Publications in Astronomy -- a Case Study of Indian Institute of Astrophysics Repository

Science.gov (United States)

Birdie, C.; Vagiswari, A.

2007-10-01

The continued escalation of journal prices, and inadequate access to scholarly journals along with a consistent reduction in library resources and the advent of new technologies have all contributed to a change in the present scholarly communication. The initiative towards establishing Open Access communication has been advocated among scholars and researchers. An Institutional Archive for holding pre- and post-prints of articles written by academic and research staff increases the accessibility, visibility and impact of research output. The Indian Institute of Astrophysics (IIA) is one of the astronomical research institutes in India pioneering the Open Access movement. The institute has set up a pilot project to store the institute's publications in an institutional repository (IR). The library at IIA plays an important role in setting up this archive. While the authors and publishers are the key players in this endeavor, the role of librarians needs to be redefined in the present paradigm shift of publishing. When the Institutes decide to develop their own repositories, the skills and expertise of librarians are needed to design, develop, manage and maintain a successful repository. These and the knowledge of copyright issues relevant to the digital content of IRs are highlighted in this paper. This paper also discusses the various opportunities and tools available for librarians to learn the procedures and involve themselves in establishing their institutional repositories.

Impact analysis on ESF design for Calico Hills penetration and exploratory drift and tuff main extension to limits of the repository block

International Nuclear Information System (INIS)

Grenia, J.; Weyand, L.

1988-01-01

The study covers the impacts on project costs, schedule, human resources and engineering designs caused by increases in site characterization activity consisting of penetration of the Calico Hills formation by ES-1 shaft with exploratory drifting to the Ghost Dance fault and/or drifting 10,000 feet southward from the MTL ESF test complex area to the end of the future repository block

Review of the potential effects of alkaline plume migration from a cementitious repository for radioactive waste

International Nuclear Information System (INIS)

Savage, D.

1997-01-01

Extensive use of cement and concrete is envisaged in the construction of geological repositories for low and intermediate-level radioactive wastes, both for structural, and encapsulation and backfilling purposes. Saturation of these materials with groundwater may occur in the post-closure period of disposal, producing a hyperalkaline pore fluid with a pH in the range 10-13.5. These pore fluids have the potential to migrate from the repository according to local groundwater flow conditions and react chemically with the host rock. These chemical reactions may affect the rock's capacity to retard the migration of radionuclides released from the repository after the degradation of the waste packages. The effects of these chemical reactions on the behaviour of the repository rock as a barrier to waste migration need to be investigated for the purposes of assessing the safety of the repository design (so-called 'safety assessment' or 'performance assessment'). The objectives of the work reported here were to: identify those processes influencing radionuclide mobility in the geosphere which could be affected by plume migration; review literature relevant to alkali-rock reaction; contact organisations carrying out relevant research and summarise their current and future activities; and make recommendations how the effects of plume migration can be incorporated into models of repository performance assessment. (author)

The Efficacy of Institutional Repositories: Reflections on the Development of a Personalised Collection on UPSpace

Science.gov (United States)

Olivier, Elsabe

2007-01-01

There is much speculation that the development of institutional repositories will impact on or even change the traditional scholarly communication process. The purpose of this conversation is to introduce the reader to the use of and response to institutional repositories which were initiated by the Open Access Initiative. The concept of…

State-of-the-art for evaluating the potential effects of erosion and deposition on a radioactive waste repository. Final report

International Nuclear Information System (INIS)

1980-01-01

The potential impact of future geologic processes on the integrity of a deep, high-level radioactive-waste repository is evaluated. The following study identifies the potential consequences of surface erosion and deposition on sub-surface repository containment characteristics and assesses the ability to measure and predict quantitatively the rates and corresponding extent of these processes in the long term. Numerous studies of the magnitudes and rates of surficial erosion and deposition that have been used to determine the minimum allowable depth for a geologic repository (300 m - NRC Code of Federal Regulations, Part 60.122, Draft 10) are cited in this report. Measurement and interpretation of potential rates and extent of surficial processes in these studies involved considerable uncertainty, and the implications of this uncertainty on presently proposed repository siting criteria are addressed herein. Important concepts that should be considered when developing siting criteria to protect against deleterious effects arising from future erosion or deposition are highlighted. Erosion agents that could affect deep repositories are distinguished in this report so that their individual and combined impacts may be examined. This approach is recommended when evaluating potential repository sites in diverse environments that are susceptible to different agents of erosion. In contrast, agents of sedimentation are not differentiated in this report because of their relatively minor impact on a deep repository

The radiation resistance and cobalt biosorption activity of yeast strains isolated from the Lanyu low-level radioactive waste repository in Taiwan

International Nuclear Information System (INIS)

Li, Chia-Chin; Chung, Hsiao-Ping; Wen, Hsiao-Wei; Chang, Ching-Tu; Wang, Ya-Ting; Chou, Fong-In

2015-01-01

The ubiquitous nature of microbes has made them the pioneers in radionuclides adsorption and transport. In this study, the radiation resistance and nuclide biosorption capacity of microbes isolated from the Lanyu low-level radioactive waste (LLRW) repository in Taiwan was assessed, the evaluation of the possibility of using the isolated strain as biosorbents for 60 Co and Co (II) from contaminated aqueous solution and the potential impact on radionuclides release. The microbial content of solidified waste and broken fragments of containers at the Lanyu LLRW repository reached 10 5  CFU/g. Two yeast strains, Candida guilliermondii (CT1) and Rhodotorula calyptogenae (RT1) were isolated. The radiation dose necessary to reduce the microbial count by one log cycle of CT1 and RT1 was 2.1 and 0.8 kGy, respectively. Both CT1 and RT1 can grow under a radiation field with dose rate of 6.8 Gy/h, about 100 times higher than that on the surface of the LLRW container in Lanyu repository. CT1 and RT1 had the maximum 60 Co biosorption efficiency of 99.7 ± 0.1% and 98.3 ± 0.2%, respectively in 60 Co aqueous solution (700 Bq/mL), and the 60 Co could stably retained for more than 30 days in CT 1. Nearly all of the Co was absorbed and reached equilibrium within 1 h by CT1 and RT1 in the 10 μg/g Co (II) aqueous solution. Biosorption efficiency test showed almost all of the Co (II) was adsorbed by CT1 in 20 μg/g Co (II) aqueous solution, the efficiency of biosorption by RT1 in 10 μg/g of Co (II) was lower. The maximum Co (II) sorption capacity of CT1 and RT1 was 5324.0 ± 349.0 μg/g (dry wt) and 3737.6 ± 86.5 μg/g (dry wt), respectively, in the 20 μg/g Co (II) aqueous solution. Experimental results show that microbial activity was high in the Lanyu LLRW repository in Taiwan. Two isolated yeast strains, CT1 and RT1 have high potential for use as biosorbents for 60 Co and Co (II) from contaminated aqueous solution, on the other hand, but may have the impact on

Repository design

Energy Technology Data Exchange (ETDEWEB)

John, C M

1982-01-01

Various technical issues of radioactive waste design are addressed in this paper. Two approaches to repository design considered herein are: (1) design to minimize the disturbance of the hot rock; and (2) designs that intentionally modify the hot rock to insure better containment of the wastes. The latter designs range from construction of a highly impermeable barrier around a spherical cavern to creating a matrix of tunnels and boreholes to form a cage within which the hydraulic pressure is nearly constant. Examples of these design alternatives are described in some detail. It is concluded that proposed designs for repositories illustrate that performance criteria considered acceptable for such facilities can be met by appropriate site selection and repository engineering. With these technically feasible design concepts, it is also felt that socioeconomic and institutional issues can be better resolved. (BLM)

Thermal modeling for a potential high-level nuclear waste repository at Yucca Mountain, Nevada

International Nuclear Information System (INIS)

Pruess, K.; Tsang, Y.

1994-03-01

Repository performance models based on numerical simulation of fluid and heat flows have recently been developed by several different groups. Model conceptualizations generally focus on large-scale average behavior. This comparison finds that current performance assessment (PA) models use generally similar approximations and parameters. Certain differences exist in some performance-relevant parameters, especially absolute permeabilities, characteristic curves, and thermal conductivities. These reflect present uncertainties about the most appropriate parameters applicable to Yucca Mountain and must be resolved through future field observations and laboratory measurements. For a highly heterogeneous fractured-porous hydrogeologic system such as Yucca Mountain, water infiltration through the unsaturated zone is expected to be dominated by highly localized phenomena. These include fast channelized flow along preferential paths in fractures, and frequent local ponding. The extended dry repository concept proposed by the Livermore group is reviewed. Predictions of large-scale drying around the repository on the average for large thermal loads cannot be taken to indicate that waste packages will not be contacted by liquid water, and that aqueous-phase transport of contaminants is not possible. Specifically, the authors find that modest water infiltration, on the order of a few millimeters per year, would be sufficient to overwhelm the vaporization capacity of the repository heat and inundate the waste packages within a time frame of a few thousand years. A preliminary analysis indicates that channelized flow of water may persist over large vertical distances. The vaporization-condensation cycle has a capacity for generating huge amounts of ponded water. A small fraction of the total condensate, if ponded and then episodically released, would be sufficient to cause liquid phase to make contact with the waste packages

NWTS conceptual reference repository description (CRRD). Volume 1. Summary

International Nuclear Information System (INIS)

1981-05-01

This report is a Conceptual Reference Repository Description (CRRD) for the terminal storage of spent, unreprocessed fuel assemblies and low-level transuranic waste. It is based on the following three previously prepared conceptual design reports: National Waste Terminal Storage in a Bedded Salt Formation for Spent Unreprocessed Fuel (NWTS-R2), prepared by Kaiser Engineers; National Waste Terminal Storage Repository Number 1 (NWTS-R1), prepared by Stearns-Roger; Spent Fuel Receiving and Packaging Facility Conceptual Design, prepared by Rockwell Hanford Operations and Kaiser Engineers. The CRRD is not itself a conceptual design report, but combines the key features of the above three reports into a description of a reference repository. This description is to be used as a basis for the preparation of a preliminary information report for the repositories. The CRRD discusses from a conceptual engineering standpoint the structures, systems, equipment, and operations necessary to (1) receive unreprocessed spent fuel assemblies via standard shipping casks, (2) offload these assemblies, (3) place the assemblies in canisters, (4) transport the canisters to underground storage locations in the salt dome, and (5) place these canisters in terminal storage. The CRRD also elaborates on the concepts for the retrieval and recovery of the spent fuel after burial; describes the development of the shafts and the underground areas,as well as the supporting operational utility and administrative features of the repository; and discusses the impacts on the reference repository of (1) changes in the waste package concept, (2) dry receiving and dry temporary storage of waste, (3) terminal storage of reprocessing waste, and (4) alternative underground development schemes

Centralized mouse repositories.

Science.gov (United States)

Donahue, Leah Rae; Hrabe de Angelis, Martin; Hagn, Michael; Franklin, Craig; Lloyd, K C Kent; Magnuson, Terry; McKerlie, Colin; Nakagata, Naomi; Obata, Yuichi; Read, Stuart; Wurst, Wolfgang; Hörlein, Andreas; Davisson, Muriel T

2012-10-01

Because the mouse is used so widely for biomedical research and the number of mouse models being generated is increasing rapidly, centralized repositories are essential if the valuable mouse strains and models that have been developed are to be securely preserved and fully exploited. Ensuring the ongoing availability of these mouse strains preserves the investment made in creating and characterizing them and creates a global resource of enormous value. The establishment of centralized mouse repositories around the world for distributing and archiving these resources has provided critical access to and preservation of these strains. This article describes the common and specialized activities provided by major mouse repositories around the world.

An evaluation of repository-induced disturbances for a KBS-3 type repository

Energy Technology Data Exchange (ETDEWEB)

Savage, D.; McLeod, R.; McEwen, T. [QuantiSci, Melton Mowbray (United Kingdom)

1998-03-01

This report considers the potential physical and chemical perturbations caused by the excavation, operation and backfilling and sealing of a KBS-3 type repository for spent fuel in Sweden. Parts of the underground excavations are likely to remain open to the atmosphere for up to several decades. Time-dependent changes to the chemical environment and the properties of the geological formation will be occurring as well as the initial disturbance of construction and subsequent changes after backfilling. In addition, this report also discusses issues that arise from the co-disposal of spent fuel and intermediate level waste. The processes which are likely to act during each stage of a repository from construction through to backfilling and sealing have been reviewed and the degree to which these processes are understood and represented within the performance assessment is discussed. The areas of particular interest are: The coupling of thermal, hydrogeological and mechanical processes with particular reference to the development of the near-field; Understanding the transient process of re-saturation with particular reference to the buffer material surrounding the waste canisters, including chemical changes to the material; The impact of accidental events during the construction and operational phases of work and their possible consequence on the long term performance of the repository; Chemical issues relating to the co-disposal of spent fuel and intermediate level wastes within a single facility. When consideration of transient processes and coupling is discussed, it is apparent that numerical tools and a complete understanding to provide quantitative information is lacking. The importance of the engineered barrier system within the performance assessment for spent fuel disposal is recognised and the emphasis is placed on the understanding of the coupled processes in the evolution in the near-field of the geosphere 45 refs, 4 fig, 2 tabs

An evaluation of repository-induced disturbances for a KBS-3 type repository

International Nuclear Information System (INIS)

Savage, D.; McLeod, R.; McEwen, T.

1998-03-01

This report considers the potential physical and chemical perturbations caused by the excavation, operation and backfilling and sealing of a KBS-3 type repository for spent fuel in Sweden. Parts of the underground excavations are likely to remain open to the atmosphere for up to several decades. Time-dependent changes to the chemical environment and the properties of the geological formation will be occurring as well as the initial disturbance of construction and subsequent changes after backfilling. In addition, this report also discusses issues that arise from the co-disposal of spent fuel and intermediate level waste. The processes which are likely to act during each stage of a repository from construction through to backfilling and sealing have been reviewed and the degree to which these processes are understood and represented within the performance assessment is discussed. The areas of particular interest are: The coupling of thermal, hydrogeological and mechanical processes with particular reference to the development of the near-field; Understanding the transient process of re-saturation with particular reference to the buffer material surrounding the waste canisters, including chemical changes to the material; The impact of accidental events during the construction and operational phases of work and their possible consequence on the long term performance of the repository; Chemical issues relating to the co-disposal of spent fuel and intermediate level wastes within a single facility. When consideration of transient processes and coupling is discussed, it is apparent that numerical tools and a complete understanding to provide quantitative information is lacking. The importance of the engineered barrier system within the performance assessment for spent fuel disposal is recognised and the emphasis is placed on the understanding of the coupled processes in the evolution in the near-field of the geosphere

Demystifying the institutional repository for success

CERN Document Server

Buehler, Marianne

2013-01-01

Institutional repositories remain key to data storage on campus, fulfilling the academic needs of various stakeholders. Demystifying the Institutional Repository for Success is a practical guide to creating and sustaining an institutional repository through marketing, partnering, and understanding the academic needs of all stakeholders on campus. This title is divided into seven chapters, covering: traditional scholarly communication and open access publishing; the academic shift towards open access; what the successful institutional repository looks like; institutional repository collaboratio

The fate of organic compounds in a cement-based repository: impact on the engineered barrier and the release of C-14 from the near field

International Nuclear Information System (INIS)

Wieland, E.; Rothardt, J.; Schlotterbeck, G.

2015-01-01

The degradation of organic materials is taken into account in the safety analysis for a L/ILW (Low- and intermediate-level radioactive waste) repository in Switzerland with the aim of assessing possible impacts on the cement barrier. The waste forms to be disposed of in the planned L/ILW repository will contain HMW polymers and LMW monomeric organic materials. It is anticipated that these organic materials have different degradation rates and therefore different life times in a repository. While the decomposition of LMW organics is expected to be fast and complete during the oxic and early anoxic states of a repository, i.e. before and shortly after repository closure, the decomposition of the HMW polymeric materials is expected to be very slow and, for some materials, to occur over the entire life time of the repository. The degradation of organic materials generates CO 2 which gives rise to carbonation of the cement barrier. The maximum acceptable loading of organics in the near field with no detrimental effect on radionuclide immobilization can be estimated on the assumption that at maximum 2/3 of the total portlandite inventory of hydrated cement is allowed to convert to CaCO 3 in the case of waste compartments for which the cementitious barrier should remain intact. The maximum loading is determined by the inventory of the organic material under consideration as well as the carbon content and the oxidation state of carbon of the material. Carbon-14 bound in organic compounds is considered to be an important contributor to the annual dose released from a L/ILW repository. While the 14 C inventory is well known, the chemical speciation of 14 C in the cementitious near field upon liberation in the course of the corrosion of activated steel is only poorly understood. Preliminary corrosion tests with non-activated steel powders show the formation of gaseous and dissolved organic carbon species, e.g. alkanes/alkenes, alcohols, aldehydes, and carboxylic acids

The European Repository Landscape 2008 Inventory of Digital Repositories for Research Output

CERN Document Server

Van der Graaf, Maurits

2009-01-01

It is widely acknowledged that a common knowledge base for European research is necessary. Research repositories are an important innovation to the scientific information infrastructure. In 2006, digital repositories in the 27 countries of the European we

National radioactive waste repository draft EIS. 2 volumes

International Nuclear Information System (INIS)

2002-01-01

Most Australians benefit either directly or indirectly from the medical, industrial and scientific use of radioactive materials. This use produces a small amount of radioactive waste, including low level and short-lived intermediate level radioactive waste such as lightly contaminated soil, plastic, paper, laboratory equipment, smoke detectors, exit signs and gauges.This waste is temporarily stored at more than 100 urban and rural locations around Australia, much of it in buildings that were neither designed nor located for the long-term storage of radioactive material and that are nearing or have reached capacity. Storage locations include hospitals, research institutions, and industry and government stores. Storing such waste in many locations in non-purpose built facilities potentially poses greater risk to the environment and people than disposing of the material in a national, purpose-built repository where the material can be safely managed and monitored. The objectives of the national repository are to: 1. strengthen Australia's radioactive waste management arrangements by promoting the safe and environmentally sound management of low level and short-lived intermediate level radioactive waste 2. provide safe containment of these wastes until the radioactivity has decayed to background levels. To meet these objectives, it is proposed to construct a national near-surface repository at either the preferred site on the Woomera Prohibited Area (WPA) or either of the two nearby alternative sites. The facility is not intended for the disposal of radioactive ores from mining. A national store for long-lived intermediate level waste will not be co-located with the national repository, and would be subject to a separate environmental assessment process.One preferred and two alternative sites have been selected for the national repository, following an extensive site selection process. All three sites are located in northern South Australia in a region known as central

Hydrological and thermal issues concerning a nuclear waste repository in fractured rocks

International Nuclear Information System (INIS)

Wang, J.S.Y.

1991-12-01

The characterization of the ambient conditions of a potential site and the assessment of the perturbations induced by a nuclear waste repository require hydrological and thermal investigations of the geological formations at different spatial and temporal scales. For high-level wastes, the near-field impacts depend on the heat power of waste packages and the far-field long-term perturbations depend on the cumulative heat released by the emplaced wastes. Surface interim storage of wastes for several decades could lower the near-field impacts but would have relatively small long-term effects if spent fuels were the waste forms for the repository. One major uncertainty in the assessment of repository impacts is from the variation of hydrological properties in heterogeneous media, including the effects of fractures as high-permeability flow paths for containment migration. Under stress, a natural fracture cannot be represented by the parallel plate model. The rock surface roughness, the contact area, and the saturation state in the rock matrix could significantly change the fracture flow. In recent years, the concern of fast flow through fractures in saturated media has extended to the unsaturated zones. The interactions at different scales between fractures and matrix, between fractured matrix unites and porous units, and between formations and faults are discussed

Source terms; isolation and radiological consequences of carbon-14 waste in the Swedish SFR repository

International Nuclear Information System (INIS)

Hesboel, R.; Puigdomenech, I.; Evans, S.

1990-01-01

The source term, isolation capacity, and long-term radiological exposure of 14 C from the Swedish underground repository for low and intermediate level waste (SFR) is assessed. The prospective amount of 14 C in the repository is assumed to be 5 TBq. Spent ion exchange resins will be the dominant source of 14 C. The pore water in the concrete repository is expected to maintain a pH of >10.5 for a period of at least 10 6 y. The cement matrix of the repository will retain most of the 14 CO 3 2- initially present. Bacterial production of CO 2 and CH 4 from degradation of ion-exchange resins and bitumen may contribute to 14 C release to the biosphere. However, CH 4 contributes only to a small extent to the overall carbon loss from freshwater ecosystems. The individual doses to local and regional individuals peaked with 5x10 -3 and regional individuals peaked with 5x10 -3 and 8x10 -4 μSv y -1 respectively at about 2.4x10 4 years. A total leakage of 8.4 GBq of 14 C from the repository will cause a total collective dose commitment of 1.1 manSv or 130 manSv TBq -1 . (authors)

Office of Geologic Repositories quality assurance plan for high-level radioactive waste repositories

International Nuclear Information System (INIS)

1986-08-01

This document sets forth geologic repository program-wide quality assurance program requirements and defines management's quality assurance responsibilities for the Office of Geologic Repositories and its projects. (LM)

Virtual patient repositories--a comparative analysis.

Science.gov (United States)

Küfner, Julia; Kononowicz, Andrzej A; Hege, Inga

2014-01-01

Virtual Patients (VPs) are an important component of medical education. One way to reduce the costs for creating VPs is sharing through repositories. We conducted a literature review to identify existing repositories and analyzed the 17 included repositories in regards to the search functions and metadata they provide. Most repositories provided some metadata such as title or description, whereas other data, such as educational objectives, were less frequent. Future research could, in cooperation with the repository provider, investigate user expectations and usage patterns.

Introduction to the second international workshop on the design and construction of final repositories

International Nuclear Information System (INIS)

Simmons, G.R.

1995-01-01

Canadian repository design studies are reviewed. Two conceptual designs are described. The first is a single-level spent-fuel repository using the in-floor borehole emplacement configuration. The disposal container for 72 bundles is made of titanium. The depth will probably be 1000 m. Maximum temperature must not exceed 100 deg C. The near-surface extension zone must not exceed 100 m in depth. The cost for disposal of 10.1 million bundles over 89 years is estimated to be about C$13 billion. The second concept, a single level spent-fuel repository using the in-room emplacement configuration, may be more suitable for the stress conditions that may be encountered in the plutonic rocks of the Canadian shield at a depth greater than 500 m. In this case, the container is made of copper, and the capacity of the repository will be determined by maintaining the emplacement area at about 2 km square, and the required container to container and room to room spacing to satisfy the temperature criterion. A concrete floor will be provided.The buffer material will be formed in pre-compacted blocks. 10 refs., 1 tab., 4 figs

Dose calculation for accident situations at WWR-S type spent nuclear fuel repository

International Nuclear Information System (INIS)

Margeanu, S.; Florescu, G.

2006-01-01

Full text: The Spent Nuclear Fuel Repository at IFIN-HH Bucharest (SNFR IFIN-HH) consists in four pools, repository hall, radiological monitoring system, ventilation system and auxiliary systems. At the moment the remaining activity in the repository is about 3500 Ci. Despite of the small activity, for emergency preparedness purposes, several accident scenarios, with a non zero probability of occurrence during the repository lifetime, have been postulated. Evaluations of radiological consequences to personnel, general public and environment, for each accident scenario have been performed. The radioactive inventory was evaluated with ORIGEN code from SCALE computer code system and radiological consequences were evaluated with COSYMA computer code. Assumptions for the source term determination, meteorological conditions and release, are presented. The calculated values of doses and risk are also presented. The impact of these accident scenarios on population and environment is also discussed. (authors)

Technology overview of mined repositories

International Nuclear Information System (INIS)

Gimera, R.; Thirumalai, K.

1982-01-01

Mined repositories present an environmentally viable option for permanent disposal of nuclear waste. This paper reviews the state-of-the-art mining technologies and identifies technological issues and developments necessary to mine a repository in basalt. The thermal loading, isolation, and retrieval requirements of a repository present unique technological challenges unknown to conventional mining practice. The technology issues and developments required in the areas of excavation, roof and ground support, equipment development, instrumentation development, and sealing are presented. Performance assessment methods must be developed to evaluate the adequacies of technologies developed to design, construct, operate, and decommission a repository. A stepwise test-and-development approach is used in the Basalt Waste Isolation Project to develop cost-effective technologies for a repository

Breast Cancer Tissue Repository

National Research Council Canada - National Science Library

Iglehart, J

1997-01-01

The Breast Tissue Repository at Duke enters its fourth year of finding. The purpose of the Repository at Duke is to provide substantial quantities of frozen tissue for explorative molecular studies...

Enlargement of the Baldone near-surface radioactive waste repository

International Nuclear Information System (INIS)

Dreimanis, A.

2007-01-01

A unified analysis of the enlargement of the Baldone near-surface radioactive waste (RW) repository RADONS considers the interplay of the existing engineering, safety and infrastructure premises, with the foreseen newly socio-technical features. This enlargement consists in construction of two additional RW disposal vaults and in building a long-term storage facility for spent sealed sources at the RADONS territory. Our approach is based on consecutive analysis of following basic elements: - the origin of enlargement - the RADONS safety analysis and a set of optimal socio-technical solutions of Salaspils research reactor decommissioning waste management; - the enlargement - a keystone of the national RW management concept, including the long-term approach; - the enlargement concept - the result of international co-operation and obligations; - arrangement optimization of new disposal and storage space; - environmental impact assessment for the repository enlargement - the update of socio-technical studies. The study of the public opinion revealed: negative attitude to repository enlargement is caused mainly due to missing information on radiation level and on the RADONS previous operations. These results indicate: basic measures to improve the public attitude to repository enlargement: the safety upgrade, public education and compensation mechanisms. A detailed stakeholders engagement and public education plan is elaborated. (author)

An evaluation of environmental effects of the DOE HLW repository siting and characterization program at Yucca Mountain, Nevada

International Nuclear Information System (INIS)

Winsor, M.F.; Ulland, L.M.

1989-01-01

This paper presents highlights of the Nevada Nuclear Waste Project Office (NWPO) environmental investigations in progress on the environmental effects of past and proposed activities of the Department of Energy (DOE) at the Yucca Mountain repository. The environmental investigations refer to those studies specifically related to resource evaluation, impact assessment and mitigation planning for the repository program; it is defined to exclude consideration of technical suitability determinations, socioeconomics and transportation. This paper addresses the question of what are the disturbances created by past and proposed DOE activities related to repository siting and characterization at Yucca Mountain. It discusses considerations in linking disturbance to the potential for significant adverse environmental impacts

The Laxemar and Forsmark repositories. An analysis of the water inflow distribution

International Nuclear Information System (INIS)

Svensson, Urban

2006-12-01

A numerical simulation model is used to estimate the water inflow distribution to the Laxemar and Forsmark repositories. In particular statistics for the inflow to individual deposition holes, i.e. inflow distribution expressed as litre/min, deposition hole, is requested. Different grouting efficiencies are evaluated, including no grouting. The simulations are based on the code DarcyTools version 3.0, which was also used in simulations of the impact of the Repositories in Forsmark and Laxemar. Both the code and the simulations include many novel features and all simulations should hence be regarded as tentative. For the Laxemar repository it is found that less than 2% of all deposition holes will have an inflow larger than 1.0 l/min. This number will increase to about 20% if the inflow limit is put to 0.1 l/min. For the Forsmark repository it is found that 99.9% of all deposition holes will have an inflow smaller than 0.01 l/min

Modeling the impact of climate change in Germany with biosphere models for long-term safety assessment of nuclear waste repositories

International Nuclear Information System (INIS)

Staudt, C.; Semiochkina, N.; Kaiser, J.C.; Pröhl, G.

2013-01-01

Biosphere models are used to evaluate the exposure of populations to radionuclides from a deep geological repository. Since the time frame for assessments of long-time disposal safety is 1 million years, potential future climate changes need to be accounted for. Potential future climate conditions were defined for northern Germany according to model results from the BIOCLIM project. Nine present day reference climate regions were defined to cover those future climate conditions. A biosphere model was developed according to the BIOMASS methodology of the IAEA and model parameters were adjusted to the conditions at the reference climate regions. The model includes exposure pathways common to those reference climate regions in a stylized biosphere and relevant to the exposure of a hypothetical self-sustaining population at the site of potential radionuclide contamination from a deep geological repository. The end points of the model are Biosphere Dose Conversion factors (BDCF) for a range of radionuclides and scenarios normalized for a constant radionuclide concentration in near-surface groundwater. Model results suggest an increased exposure of in dry climate regions with a high impact of drinking water consumption rates and the amount of irrigation water used for agriculture. - Highlights: ► We model Biosphere Dose Conversion Factors for a representative group exposed to radionuclides from a waste repository. ► The BDCF are modeled for different soil types. ► One model is used for the assessment of the influence of climate change during the disposal time frame.

Prestudy Oskarshamn. Tourism in Oskarshamn with or without a repository; Foerstudie Oskarshamn. Turismen i Oskarshamn med eller utan djupfoervar

Energy Technology Data Exchange (ETDEWEB)

Nordblom, C.J.; Foghagen, C. [Hoegskolan i Kalmar (Sweden). Inst. foer samhaellsvetenskap med ekonomi

1998-11-01

Consequences for the tourism at Oskarshamn from siting a spent fuel repository in the community are studied. Four questionnaire/interview enquires were performed, and the analysis of the results show that no noticeable effects are expected. Still, an uncertainty about the impact of a repository is felt by the public, and more thorough information about the repository and its components is needed

Source terms for analysis of accidents at a high level waste repository

International Nuclear Information System (INIS)

Mubayi, V.; Davis, R.E.; Youngblood, R.

1989-01-01

This paper describes an approach to identifying source terms from possible accidents during the preclosure phase of a high-level nuclear waste repository. A review of the literature on repository safety analyses indicated that source term estimation is in a preliminary stage, largely based on judgement-based scoping analyses. The approach developed here was to partition the accident space into domains defined by certain threshold values of temperature and impact energy density which may arise in potential accidents and specify release fractions of various radionuclides, present in the waste form, in each domain. Along with a more quantitative understanding of accident phenomenology, this approach should help in achieving a clearer perspective on scenarios important to preclosure safety assessments of geologic repositories. 18 refs., 3 tabs

Preliminary post-closure safety assessment of repository concepts for low level radioactive waste at the Bruce Site, Ontario

International Nuclear Information System (INIS)

Little, R.H.; Penfold, J.S.S.; Egan, M.J.; Leung, H.

2005-01-01

The preliminary post-closure safety assessment of permanent repository concepts for low-level radioactive waste (LLW) at the Ontario Power Generation (OPG) Bruce Site is described. The study considered the disposal of both short and long-lived LLW. Four geotechnically feasible repository concepts were considered (two near-surface and two deep repositories). An approach consistent with best international practice was used to provide a reasoned and comprehensive analysis of post-closure impacts of the repository concepts. The results demonstrated that the deep repository concepts in shale and in limestone, and the surface repository concept on sand should meet radiological protection criteria. For the surface repository concept on glacial till, it appears that increased engineering such as grouting of waste and voids should be considered to meet the relevant dose constraint. Should the project to develop a permanent repository for LLW proceed, it is expected that this preliminary safety assessment would need to be updated to take account of future site-specific investigations and design updates. (author)

Barriers of repository under the conditions of underground isolation of heat releasing radioactive waste in permafrost

International Nuclear Information System (INIS)

Kazakov, A.N.; Fedorovich, L.N.

1995-01-01

The main positions and the leading principle of the ensuring of the environmental safety of the method of the underground isolation of radioactive waste in permafrost rock are presented in this work and it is shown here the peculiarities in realization of the principle of the multibarrier protection. It is substantiated here the principle of the optimal time of the capacity for work of the repository's engineered barriers. The possibility of the exclusion of the radionuclides migration beyond the working volume of the repository during the time of the potential danger of radioactive waste is also substantiated in these papers

An assessment of the radiological impact of human intrusion at the UK Low Level Waste Repository (LLWR) - 59356

International Nuclear Information System (INIS)

Hicks, Tim; Baldwin, Tamara; Cummings, Richard; Sumerling, Trevor

2012-01-01

The UK Low Level Waste Repository Ltd submitted an Environmental Safety Case for the disposal of low-level waste (LLW) to the Environment Agency on the 1 May 2011. The Environmental Safety Case (ESC) presents a complete case for the environmental safety of the Low Level Waste Repository (LLWR) both during operations and in the long term (Cummings et al, in these proceedings). This includes an assessment of the long-term radiological safety of the facility, including an assessment of the potential consequences of human intrusion at the site. The human intrusion assessment is based on a cautiously realistic approach in defining intrusion cases and parameter values. A range of possible human intrusion events was considered based on present-day technologies and credible future uses of the site. This process resulted in the identification of geotechnical investigations, a housing development and a smallholding as requiring quantitative assessment. A particular feature of the site is that, because of its proximity to the coast and in view of expected global sea-level rise, it is vulnerable to coastal erosion. During such erosion, wastes and engineered barrier materials will be exposed, and could become targets for investigation or recovery. Therefore, human intrusion events have been included that are associated with such activities. A radiological assessment model has been developed to analyse the impacts of potential human intrusion at the site. A key feature of the model is the representation of the spatial layout of the disposal site, including the engineered cap design and the large-scale spatial heterogeneity of radionuclide concentrations within the repository. The model has been used to calculate the radiation dose to intruders and to others following intrusion at different times and at different locations across the site, for the each of the selected intrusion events, considering all relevant exposure modes. Potential doses due to radon and its daughters in

Impact of Operating Rules on Planning Capacity Expansion of Urban Water Supply Systems

Science.gov (United States)

de Neufville, R.; Galelli, S.; Tian, X.

2017-12-01

This study addresses the impact of operating rules on capacity planning of urban water supply systems. The continuous growth of metropolitan areas represents a major challenge for water utilities, which often rely on industrial water supply (e.g., desalination, reclaimed water) to complement natural resources (e.g., reservoirs). These additional sources increase the reliability of supply, equipping operators with additional means to hedge against droughts. How do their rules for using industrial water supply impact the performance of water supply system? How might it affect long-term plans for capacity expansion? Possibly significantly, as demonstrated by the analysis of the operations and planning of a water supply system inspired by Singapore. Our analysis explores the system dynamics under multiple inflow and management scenarios to understand the extent to which alternative operating rules for the use of industrial water supply affect system performance. Results first show that these operating rules can have significant impact on the variability in system performance (e.g., reliability, energy use) comparable to that of hydro-climatological conditions. Further analyses of several capacity expansion exercises—based on our original hydrological and management scenarios—show that operating rules significantly affect the timing and magnitude of critical decisions, such as the construction of new desalination plants. These results have two implications: Capacity expansion analysis should consider the effect of a priori uncertainty about operating rules; and operators should consider how their flexibility in operating rules can affect their perceived need for capacity.

Local economic impacts associated with pure taxable capacity changes

International Nuclear Information System (INIS)

Bjornstad, D.J.

1982-01-01

A fiscal-impact model based on the introduction of a nuclear power plant demonstrates the need to integrate local public-sector impacts with local private-sector impacts when estimating the economic changes a community undergoes in response to a significant exogenous shock. A nuclear plant differs from other electrical generating facilities because siting regulations require locating in a low-population density area where the influence on the community will be substantial. These characteristics approximate the pure fiscal capacity change or pure tax revenue importation concept. Four sections of the paper describe local decision making on taxes, identify the parameters that may shape local impact, analyze indifference curves as they integrate with the local macroeconomic model, and compare data for two communities in which both private and public local economic sectors show stimulation. 12 references, 1 figure

INSTITUTIONAL REPOSITORY: EMPLOYMENT IN EDUCATION

Directory of Open Access Journals (Sweden)

Vasyl P. Oleksyuk

2012-11-01

Full Text Available The article investigated the concept of «institutional repository» and determined the aspects of institutional repositories in higher education. Institutional Repositories are information systems that allow preserving, storing and disseminating scientific knowledge produced in higher education and scientific research institutions. This study presented the main aspects using institutional repositories in educational process (such as storage of scientific and educational information, means of organization activity of students, object of studying. This article produced the structure of communities and collections of the institutional. It is described the experience of implementing of DSpace in the learning process.

Diaspora Impact on the Capacity for Recovery from Conflict and Crisis

International Development Research Centre (IDRC) Digital Library (Canada)

Diaspora Impact on the Capacity for Recovery from Conflict and Crisis ... social and economic processes at the household, community and state level; the effects of ... strengthen diaspora research networks, and generate evidence-based, ...

Trust in Digital Repositories

Directory of Open Access Journals (Sweden)

Elizabeth Yakel

2013-06-01

Full Text Available ISO 16363:2012, Space Data and Information Transfer Systems - Audit and Certification of Trustworthy Digital Repositories (ISO TRAC, outlines actions a repository can take to be considered trustworthy, but research examining whether the repository’s designated community of users associates such actions with trustworthiness has been limited. Drawing from this ISO document and the management and information systems literatures, this paper discusses findings from interviews with 66 archaeologists and quantitative social scientists. We found similarities and differences across the disciplines and among the social scientists. Both disciplinary communities associated trust with a repository’s transparency. However, archaeologists mentioned guarantees of preservation and sustainability more frequently than the social scientists, who talked about institutional reputation. Repository processes were also linked to trust, with archaeologists more frequently citing metadata issues and social scientists discussing data selection and cleaning processes. Among the social scientists, novices mentioned the influence of colleagues on their trust in repositories almost twice as much as the experts. We discuss the implications our findings have for identifying trustworthy repositories and how they extend the models presented in the management and information systems literatures.

Chemical buffering capacity of clay rock

International Nuclear Information System (INIS)

Beaucaire, C.; Pearson, F.J.; Gautschi, A.

2004-01-01

The long-term performance of a nuclear waste repository is strongly dependent on the chemical properties of the host rock. The host rock establishes the chemical environment that determines such important performance attributes as radionuclide solubilities from the waste and the transport rates from the repository to the accessible environment. Clay-rich rocks are especially favourable host rocks because they provide a strong buffering capacity to resist chemical changes prompted either internally, by reactions of the waste itself and emplacement materials, or externally, by changes in the hydrologic systems surrounding the host rock. This paper will focus on three aspects of the stability of clay-rich host rocks: their ability to provide pCO 2 and redox buffering, and to resist chemical changes imposed by changes in regional hydrology and hydro-chemistry. (authors)

Desiderata for healthcare integrated data repositories based on architectural comparison of three public repositories.

Science.gov (United States)

Huser, Vojtech; Cimino, James J

2013-01-01

Integrated data repositories (IDRs) are indispensable tools for numerous biomedical research studies. We compare three large IDRs (Informatics for Integrating Biology and the Bedside (i2b2), HMO Research Network's Virtual Data Warehouse (VDW) and Observational Medical Outcomes Partnership (OMOP) repository) in order to identify common architectural features that enable efficient storage and organization of large amounts of clinical data. We define three high-level classes of underlying data storage models and we analyze each repository using this classification. We look at how a set of sample facts is represented in each repository and conclude with a list of desiderata for IDRs that deal with the information storage model, terminology model, data integration and value-sets management.

Process mining software repositories

NARCIS (Netherlands)

Poncin, W.; Serebrenik, A.; Brand, van den M.G.J.

2011-01-01

Software developers' activities are in general recorded in software repositories such as version control systems, bug trackers and mail archives. While abundant information is usually present in such repositories, successful information extraction is often challenged by the necessity to

The Ec prototype repository project: implications of assessments for refining repository design

International Nuclear Information System (INIS)

Svemar, C.

2004-01-01

The most important issue in the evaluation of the repository performance is the long term safety of the repository. Analyses for this issue focuses on the 'steady state' conditions which start at the time when the repository has been saturated and the groundwater table returned to its normal level. The bentonite buffer around the canisters is saturated and homogeneous, and the canister is located exactly in the centre of the buffer. The backfill in the tunnel has been saturated as well and fills the earlier open spaces in the tunnel completely. The task of the activities taking places prior to the start of the 'steady state' conditions, like excavation, deposition, backfilling and sealing, with due consideration to the processes a consequences they may cause in the long run, is to provide for these 'ideal' conditions, as close as possible. While studying these activities in detail it has become obvious that development of methods and techniques needs to be carefully addressed before the decision is made on how to apply them in the repository. One general finding is that the situation in engineering of details is not that much different from the situation in geological characterisation of a site in detail; one more detail of engineering and the consequences it brings often complicates the situation rather than supports the solution prioritized so far. Many of the practical issues have been studied in the Prototype Repository project in the AEspoe Hard Rock Laboratory (Pusch et al., 2000). The Prototype Repository consists of two sections with four respectively two deposition holes with bentonite buffer and canister, the latter holding electrical heaters. The sections are separated by a concrete plug, and the whole test is to be separated from the rest of the laboratory by an outer plug. The project has two objectives: 1. To demonstrate the integrated function of tile deep repository components under realistic conditions and to compare results with models and

Workshops for state review of site suitability criteria for high-level radioactive waste repositories: analysis and recommendations

International Nuclear Information System (INIS)

1978-02-01

The purpose of this report is to present the views and recommendations of invited State officials and legislators participating in a workshop concerned with preliminary site suitability criteria for high level radioactive waste repositories. The workshops were open to the public and were conducted by the U. S. Nuclear Regulatory Commission (NRC) during September 1977 in three regional locations across the United States. This contractor report is the second of two reports and consolidates the discussion by State officials on the role of a State in siting a repository, NRC's waste management program, the transportation of high level wastes, the number and location of repositories and concerns with the socio-economic impacts of siting a repository in a community. The recommendations to the NRC can be categorized into four areas. These were: (1) general recommendations, (2) procedural recommendations, (3) recommendations for improving communications, and (4) specific recommendations on the preliminary siting criteria. The recommendations emphasized the need for early State involvement in the siting process, the need for an impacted State to assess repository operations, the need for early solution of waste transportation concerns, and the requirement that any repository developed insure the protection of the public health and safety as its most important characteristic. Other participant recommendations are included in the body of the report

Technical conservatisms in NWTS repository conceptual designs. National Waste Terminal Storage Repository No. 1: special study No. 4

International Nuclear Information System (INIS)

1980-09-01

Prior studies have developed conceptual designs for National Waste Terminal Storage Repositories 1 and 2. Due to the considerable detail and volume of the documents describing these designs, it is often difficult to identify and comprehend the substantial conservatisms contained within them. This study identifies and explains the major technical conservatisms in these two conceptual designs in a concise and readily understandable format. The areas discussed include thermal loading of the geologic structure, rock mechanics and underground design, waste throughput capacity, hoisting systems, nuclear criticality safety, confinement of radioactive materials, occupational exposure and health physics, environmental effects, and cost estimates. Conservatisms are described in detail, quantified where possible, and compared to appropriate criteria

48 CFR 227.7108 - Contractor data repositories.

Science.gov (United States)

2010-10-01

... repositories. 227.7108 Section 227.7108 Federal Acquisition Regulations System DEFENSE ACQUISITION REGULATIONS... Technical Data 227.7108 Contractor data repositories. (a) Contractor data repositories may be established when permitted by agency procedures. The contractual instrument establishing the data repository must...

Deep repository for spent nuclear fuel. SR-97-Post-closure safety. Main Report. Volume I and II

International Nuclear Information System (INIS)

Hedin, A.

1999-11-01

and biosphere are analyzed in the canister defect scenario. Releases from the geosphere are converted to doses in different ecosystems. The variation in flow-related data in the geosphere has the greatest impact on the result, followed by data uncertainties for the biosphere. Other conclusions are that our understanding of fuel dissolution needs to be improved, and that the probability and size of initial canister defects that escape quality-control inspection is difficult to estimate. Risk analyses in the form of simplified probabilistic calculations are also performed. The risk analyses show that all sites lie well below the acceptance criterion. The maximum risk for release to a well is never more than 0.5 percent of the acceptance criterion, even when the calculations are extended a million years into the future. The same applies to releases to peat land for times up to 100,000 years, while the maximum risk here grows to about one-tenth of the acceptance criterion at the least favourable site at times after 100,000 years. The consequences of future climate change are explored in the climate scenario. A conceivable sequence of events, including severe glaciation, on each of the three sites is sketched for the coming 150,000 years. In the climate scenario as well, the overall conclusion is that the isolating capacity of the copper canister is not threatened by either mechanical or chemical stresses. As far as the retarding capacity of the repository is concerned, for example in the event of initial canister damage, the most important changes take place in the biosphere. The repository sites are expected to be covered by ice sheets or sea during long periods, and the aggregate effect of climate change will therefore be a reduction of the dose consequences compared with a situation where the present-day climate persists. In the earthquake scenario, the consequences of earthquakes are analyzed by means of model studies where site-specific data are used for the

Rock support for nuclear waste repositories

International Nuclear Information System (INIS)

Abramson, L.W.; Schmidt, B.

1984-01-01

The design of rock support for underground nuclear waste repositories requires consideration of special construction and operation requirements, and of the adverse environmental conditions in which some of the support is placed. While repository layouts resemble mines, design, construction and operation are subject to quality assurance and public scrutiny similar to what is experienced for nuclear power plants. Exploration, design, construction and operation go through phases of review and licensing by government agencies as repositories evolve. This paper discusses (1) the various stages of repository development; (2) the environment that supports must be designed for; (3) the environmental effects on support materials; and (4) alternative types of repository rock support

Topical session proceedings of the 4. IGSC meeting on: the potential impacts on repository safety from potential partitioning and transmutation programme

International Nuclear Information System (INIS)

Wollrath, Juergen; Voinis, Sylvie; Hadermann, Joerg; Van Luik, Abraham E.

2003-01-01

/or vitrified high-level waste. Thus, a Topical Session that focused on 'The potential impacts on repository safety from a potential P and T programme' was organised in the framework of the 4. plenary meeting of the IGSC (Integration Group for the Safety Case). This Topical Session sought to create IGSC awareness regarding potential issues involving P and T, other potential fuel cycle changes, and a repository safety case. The Topical Session focused on the recent scientific developments in potential national P and T strategies, and on international research on P and T and the potential impacts of P and T deployment on repository long-term performance and safety. 53 participants represented several national waste management organisations, regulatory authorities, and research institutions from 16 OECD member countries, IAEA and EC. The Topical Session was split in three parts: - Part A was related to national P and T strategies (e.g. which radionuclide are affected by P and T; implication on step-wise decision-making, what are the changes in potential doses...) - Part B consisted of EC and NEA/NDC presentations on the technical bases of P and T; (e.g. what is the resulting inventory of P and T, what is the schedule regarding developing and deploying P and T processes?) and, based on background provided by the previous presentations, - Part C was aimed at discussing the impact of P and T strategies on IGSC-related issues, and agreeing to key messages to be delivered to the RWMC. The current synthesis presented in part A of this document is aimed at briefly reflecting the material presented at the Topical Session and providing a short overview of the main outcomes of its discussions. The written contributions are compiled as-received without further elaboration, either as presentations or papers, in part B of the document. Part C gives the list of participants at this Topical Session

Building America Case Study: Impact of Improved Duct Insulation on Fixed-Capacity (SEER 13) and Variable-Capacity (SEER 22) Heat Pumps, Cocoa, Florida

Energy Technology Data Exchange (ETDEWEB)

2017-04-01

A new generation of central, ducted variable-capacity heat pump systems has come on the market, promising very high cooling and heating efficiency. Instead of cycling on at full capacity and then cycling off when the thermostat is satisfied, they vary their cooling and heating output over a wide range (approximately 40 to 118% of nominal full capacity); thus, staying 'on' for 60% to 100% more hours per day compared to fixed-capacity systems. Current Phase 4 experiments in an instrumented lab home with simulated occupancy evaluate the impact of duct R-value enhancement on the overall operating efficiency of the variable-capacity system compared to the fixed-capacity system.

Cumulative Impact Assessment: Approaching Environmental Capacity in Development Area Using Environmental Impact Assessment Information

Science.gov (United States)

Cho, N.; Lee, M. J.; Maeng, J. H.

2017-12-01

Environmental impact assessment estimates the impact of development as a business unit and establishes mitigation plan. If the development is done, its economic effects can spread to the nearby areas. So that various developments can be distributed at different time intervals. The impact of the new developments can be combined with existing environmental impacts and can have a larger impact. That is, Cumulative impact assessment is needed to consider the environmental capacity of the Nearby area. Cumulative impact assessments require policy tools such as environmental impact assessment information and cumulative impact estimation models. In Korea, environmental information (water quality, air quality, etc.) of the development site is measured for environmental impact assessment and monitored for a certain period (generally 5 years) after the project. In addition, by constructing the environmental information as a spatial database, it is possible to express the environmental impact on a regional basis spatially and to intuitively use it for development site selection. Utilizing a composite model of environmental impact assessment information and Remote Sensing data for cumulative impact estimation, That can be used as a policy decision support tool that provides quantitative information for development area management, such as time series effect and sprawl phenomenon.

Impact of partitioning and transmutation on high-level waste disposal for the fast breeder reactor fuel cycle

International Nuclear Information System (INIS)

Nishihara, Kenji; Oigawa, Hiroyuki; Nakayama, Shinichi; Ono, Kiyoshi; Shiotani, Hiroki

2010-01-01

The impact of partitioning and/or transmutation (PT) technology on high-level waste management was investigated for the equilibrium state of several potential fast breeder reactor (FBR) fuel cycles. Three different fuel cycle scenarios involving PT technology were analyzed: 1) partitioning process only (separation of some fission products), 2) transmutation process only (separation and transmutation of minor actinides), and 3) both partitioning and transmutation processes. The conventional light water reactor (LWR) fuel cycle without PT technology, on which the current repository design is based, was also included for comparison. We focused on the thermal constraints in a geological repository and determined the necessary predisposal storage quantities and time periods (by defining a storage capacity index) for several predefined emplacement configurations through transient thermal analysis. The relation between this storage capacity index and the required repository emplacement area was obtained. We found that the introduction of the FBR fuel cycle without PT can yield a 35% smaller repository per unit electricity generation than the LWR fuel cycle, although the predisposal storage period is prolonged from 50 years for the LWR fuel cycle to 65 years for the FBR fuel cycle without PT. The introduction of the partitioning-only process does not result in a significant reduction of the repository emplacement area from that for the FBR fuel cycle without PT, but the introduction of the transmutation-only process can reduce the emplacement area by a factor of 5 when the storage period is extended from 65 to 95 years. When a coupled partitioning and transmutation system is introduced, the repository emplacement area can be reduced by up to two orders of magnitude by assuming a predisposal storage of 60 years for glass waste and 295 years for calcined waste containing the Sr and Cs fraction. The storage period of 295 years for the calcined waste does not require a large

Analysis of Turkey’s Institutional Open Repositories: An Example of Dokuz Eylül University Institutional Open Repository

Directory of Open Access Journals (Sweden)

Korhan Levent Ertürk

2012-03-01

Full Text Available After the declaration of the Budapest Open Access Initiative in 2001, institutional open repositories are known as the most important tool of the self archiving, which is also known as green road. There are 26 institutional repositories, which are all compatible to international standards. All the institutional open repositories of Turkey mentioned before are listed in international open archive directories. In this study institutional open repository of Dokuz Eylül University is examined and institutional open repositories of Turkey are discussed.

Appraisal of hard rock for potential underground repositories of radioactive wastes. LBL-7004

International Nuclear Information System (INIS)

Cook, N.G.W.

1978-01-01

Underground burial of radioactive wastes in hard rock may be an effective and safe means of isolating them from the environment and from man. The mechanical safety and stability of such an underground repository depends largely on the virgin state of stress in the rock, groundwater pressures, the strengths of the rocks, heating by the decay of the radioactive wastes, and the layout of the excavations and the disposition of waste cannisters within them. A large body of pertinent data exists in the literature, and each of these factors has been analyzed in the light of this information. The results indicate that there are no fundamental geological nor mechanical reasons why repositories capable of storing radioactive wastes should not be excavated at suitable sites in hard rock. However, specific tests to determine the mechanical and thermal properties of the rocks at a site would be needed to provide the data for the engineering design of a repository. Also, little experience exists of the effects on underground excavations of thermal loads, so that this aspect requires theoretical study and experimental validation. The depths of these potential repositories would lie in the range from 0.5 km to 2.0 km below surface, depending upon the strength of the rock. Virgin states of stress have been measured at such depths which would retard the ingress of groundwater and obviate the incidence of faulting. A typical repository comprising three horizons each with a total area of 5 km 2 would have the capacity to store wastes with thermal output of 240 MW

Radioactive waste repository of high ecological safety

International Nuclear Information System (INIS)

Sobolev, I.; Barinov, A.; Prozorov, L.

2000-01-01

With the purpose to construct a radioactive waste repository of high ecological safety and reliable containment, MosNPO 'Radon' specialists have developed an advanced type repository - large diameter well (LBD) one. A project is started for the development of a technology for LDW repository construction and pilot operation of the new repository for 25-30 years. The 2 LDW repositories constructed at the 'Radon' site and the developed monitoring system are described

Consistency analysis of network traffic repositories

NARCIS (Netherlands)

Lastdrager, Elmer; Lastdrager, E.E.H.; Pras, Aiko

Traffic repositories with TCP/IP header information are very important for network analysis. Researchers often assume that such repositories reliably represent all traffic that has been flowing over the network; little thoughts are made regarding the consistency of these repositories. Still, for

Sellafield repository design concept

International Nuclear Information System (INIS)

1998-01-01

Between 1989 and 1997, UK Nirex Ltd carried out a programme of investigations to evaluate the potential of a site adjacent to the BNFL Sellafield works to host a deep repository for the United Kingdom's intermediate-level and certain low-level radioactive waste. The programme of investigations was wound down following the decision in March 1997 to uphold the rejection of the Company's planning application for the Rock Characterisation Facility (RCF), an underground laboratory which would have allowed further investigations to confirm whether or not the site would be suitable. Since that time, the Company's efforts in relation to the Sellafield site have been directed towards documenting and publishing the work carried out. The design concept for a repository at Sellafield was developed in parallel with the site investigations through an iterative process as knowledge of the site and understanding of the repository system performance increased. This report documents the Sellafield repository design concept as it had been developed, from initial design considerations in 1991 up to the point when the RCF planning application was rejected. It shows, from the context of a project at that particular site, how much information and experience has been gained that will be applicable to the development of a deep waste repository at other potential sites

Influence analysis of Github repositories.

Science.gov (United States)

Hu, Yan; Zhang, Jun; Bai, Xiaomei; Yu, Shuo; Yang, Zhuo

2016-01-01

With the support of cloud computing techniques, social coding platforms have changed the style of software development. Github is now the most popular social coding platform and project hosting service. Software developers of various levels keep entering Github, and use Github to save their public and private software projects. The large amounts of software developers and software repositories on Github are posing new challenges to the world of software engineering. This paper tries to tackle one of the important problems: analyzing the importance and influence of Github repositories. We proposed a HITS based influence analysis on graphs that represent the star relationship between Github users and repositories. A weighted version of HITS is applied to the overall star graph, and generates a different set of top influential repositories other than the results from standard version of HITS algorithm. We also conduct the influential analysis on per-month star graph, and study the monthly influence ranking of top repositories.

Office of Civilian Radioactive Waste Management: Annual capacity report

International Nuclear Information System (INIS)

1987-06-01

The system configuration used as the basis for this report is defined in the Mission Plan Amendment. It includes a Monitored Retrievable Storage (MRS) facility as an integral system component. During the first 10 years of WMS operation, the total quantity of spent fuel that could be accepted is 18,600 metric tons uranium (MTU). By starting WMS operations in 1998, the MRS facility could accept 6000 MTU of spent fuel by the time repository operations are projected to begin in 2003. The allocation of acceptance right is currently based on the projected annual capacity of the waste management system to receive SNF and the age of permanently discharged spent fuel. The allocations are based on the oldest fuel having the highest priority. Section 1.0 provides a discussion of the requirement for the (ACR) and the role the ACR will play in DOE's interaction with the Purchasers in implementing the provisions of the Standard Disposal Contract. The currently projected annual acceptance capacity to be allocated is discussed and presented in Section 2.0. Section 3.0 discusses the procedure and basis for allocation of this capacity (acceptance rights). Allocation will be based on the chronological listing of spent fuel assemblies and equivalent MTU. Some of the contingencies which may have an impact on Contract implementation and system operation considerations which could affect the projected annual capacity and its allocation are identified in Section 4.0. 4 refs., 11 tabs

Nye County, Nevada 1992 nuclear waste repository program: Program overview. Final report

International Nuclear Information System (INIS)

1998-01-01

The purpose of this document is to provide an overview of the Nye County FY92 Nuclear Waste Repository Program (Program). Funds to pay for Program costs will come from the Federal Nuclear Waste Fund, which was established under the Nuclear Waste Policy Act of 1982 (NWPA). In early 1983, the Yucca Mountain was identified as a potentially suitable site for the nation's first geologic repository for spent reactor fuel and high-level radioactive waste. Later that year, the Nye County Board of County Commissioners (Board) established the capability to monitor the Federal effort to implement the NWPA and evaluate the potential impacts of repository-related activities on Nye County. Over the last eight years, the County's program has grown in complexity and cost in order to address DOE's evolving site characterization studies, and prepare for the potential for facility construction and operation. Changes were necessary as well, in response to Congress's redirection of the repository program specified in the amendments, to the NWPA approved in 1987. In early FY 1991, the County formally established a project office to plan and implement its program of work. The Repository Project Office's (RPO) mission and functions are provided in Section 2.0. The RPO organization structure is described in Section 3.0

Siting guidelines and their role in repository site selection

International Nuclear Information System (INIS)

Hanlon, C.L.

1985-01-01

The first requirement of the Nuclear Waste Policy Act was for the Secretary of Energy to issue general guidelines for siting repositories. The guidelines were to specify detailed geologic considerations that would be the primary criteria for the selection of sites in various host rocks, as well as factors that would qualify or disqualify any site from development as a repository. These guidelines were clearly intended to provide not only the framework for the siting program but also the stimulus for establishing effective communication and consultation among the parties involved in the program. The Act further required that the guidelines be a factor in the development of all future decision documents of the Office of Civilian Radioactive Waste Management, including the environmental assessments that would accompany the nomination of sites for characterization, the site-characterization plans that are to be prepared before the sinking of exploratory shafts at any candidate site, and the environmental impact statement that is to support the recommendation of a site for development as a repository. More than two years after its passage, the intention of the Act for the guidelines has been realized. Concurred in by the Nuclear Regulatory Commission on June 22, 1984, and issued by the Department in November 1984, the guidelines include postclosure technical guidelines that apply to conditions governing the long-term performance of the repository system; preclosure technical guidelines that apply to conditions governing the siting, construction, operation, and closure of the repository; and system guidelines whose objective is to ensure that the regulatory requirements of the Environmental Protection Agency and the Nuclear Regulatory Commission are met

Basic repository environmental assessment design basis: Deaf Smith County site

International Nuclear Information System (INIS)

1988-03-01

This study examines the engineering factors and costs associated with the construction, operation, and decommissioning of a high-level nuclear waste repository in salt in the Palo Duro Basin in Deaf Smith County, Texas. The study assumes a repository capacity of 36,000 metric tons of heavy metal (MTHM) of unreprocessed spent fuel and 36,000 MTHM of commercial high-level reprocessing waste, along with 7,020 canisters of defense high-level reprocessing waste and associated quantities or remote- and contact-handled transuranic waste (TRU). With the exception of TRU, all the waste forms are placed in 300- to 1000-year-life carbon-steel waste packages in a collocated waste handling and packaging facility (WHPF), which is also described. The construction, operation, and decommissioning of the proposed repository is estimated to cost approximately $4.64 billion. Costs include those for the collocate WHPF, engineering, and contingency, but exclude waste form assembly and shipment to the site and waste package fabrication and shipment to the site. These costs reflect the relative average wage rates of the region, the relatively easy access to the site, and the relatively weak nature of the salt at this site. Construction would require an estimated 7 to 7.5 years. Engineering factors and costs are not strongly influenced by environmental considerations. 62 refs., 24 figs., 20 tabs

Siting of large diameter well type repositories for the central region of Russia

International Nuclear Information System (INIS)

Dmitriev, A.S.; Tkachenko, A.V.; Prozorov, L.B.; Guskov, A.V.; Korneva, S.A.

2002-01-01

To date only 14 from 16 RADON facilities are in operation. Most of them have not more than about 10% of their repositories free and available for new upcoming radioactive waste. Construction of new repositories and selection of new perspective sites is very actual problem for RAW management in Russia now. Near surface repositories are considered to be acceptable for storage of wastes with low and intermediate activity levels (LILW), which decay to safe levels in some hundreds of years. However, the experience with LILW isolation in the near surface facilities in Russia has shown that a lot of operational and natural factors impact on the engineered barriers and may cause failure of the isolation. In addition, the exploitation of the old repositories and construction of new ones require more area. Significant increase in LILW isolation reliability and area saving may be achieved by wastes disposal/storage in Large Diameter Wells (LDW), drilled in homogeneous sediments with low permeable properties. It could be considered as an intermediate between near-surface and geological repositories, and its specific features should be taken into account when choosing new sites for RAW disposal or long-term storage. (author)

CRIS and Institutional Repositories

Directory of Open Access Journals (Sweden)

A Asserson

2010-04-01

Full Text Available CRIS (Current Research Information Systems provide researchers, research managers, innovators, and others with a view over the research activity of a domain. IRs (institutional repositories provide a mechanism for an organisation to showcase through OA (open access its intellectual property. Increasingly, organizations are mandating that their employed researchers deposit peer-reviewed published material in the IR. Research funders are increasingly mandating that publications be deposited in an open access repository: some mandate a central (or subject-based repository, some an IR. In parallel, publishers are offering OA but replacing subscription-based access with author (or author institution payment for publishing. However, many OA repositories have metadata based on DC (Dublin Core which is inadequate; a CERIF (Common-European Research Information Format CRIS provides metadata describing publications with formal syntax and declared semantics thus facilitating interoperation or homogeneous access over heterogeneous sources. The formality is essential for research output metrics, which are increasingly being used to determine future funding for research organizations.

Monitored Geologic Repository Concept of Operations

International Nuclear Information System (INIS)

Curry, P.M.

1999-01-01

This updated document provides the top level guidance for development of the individual systems for the MGR which will be further developed in the System Description Documents. This document will serve as guidance for the development of functional interface and operational requirements. However, the data and engineering values presented in Monitored Geologic Repository Concept of Operations are provided as estimates or summaries of the current design. The original analyses or supporting documents must be utilized if the data or engineering values are used for design inputs. The concepts presented will be utilized as inputs for the development of operational concepts for the individual systems. It is recognized that the references listed may contain existing data or data which are to be verified. However, the data and engineering values presented will not impact the concepts presented in this technical document. As such, the data and engineering values are not being tracked as To Be Verified data. This revision was created to incorporate changes resulting from Enhanced Design Alternative II and Revision 3, DCN 01, of the Monitored Geologic Repository Requirements (YMP 1999)

Radionuclide transport from near-surface repository for radioactive waste - The unsaturated zone approach

Energy Technology Data Exchange (ETDEWEB)

Jakimaviciute-Maseliene, V. [Vilnius University (Lithuania); Mazeika, J. [Nature Research Centre (Lithuania); Motiejunas, S. [Radioactive Waste Management Agency (Lithuania)

2014-07-01

About 100 000 m{sup 3} of solid conditioned Low and Intermediate Level Waste (LILW), generated during operation and decommissioning of the Ignalina nuclear power plant (INPP), are to be disposed of in a near-surface repository (NSR) - a 'hill'-type repository with reinforced concrete vaults and with engineered and natural barriers. The northeastern Lithuania and the environment of the INPP in particular were recognized as the areas most suitable for a near-surface repository (Stabatiske Site). The engineered barriers of the repository consist of concrete cells surrounded by clay-based material of low permeability with about the same isolating capacity in all directions. The clay materials must be effectively compactable so that required hydraulic conductivity is reached. The Lithuanian Triassic clay turned out to be sufficiently rich in smectites and was proposed as main candidate for sealing of the repository. When the concrete vaults are filled, the repository cover will be constructed. The surface of the mound will be planted with grass. In this study a computer code FEFLOW 5.0 was applied for simulating the transport of the most mobile radionuclides ({sup 3}H, {sup 14}C, {sup 59}Ni and {sup 94}Nb) with moisture through an unsaturated vault of the near-surface repository in Stabatiske Site. The HYDRUS-1D analysis was used to assess the radionuclide transport in the repository and to estimate initial activity concentrations of radionuclides transported from the cemented waste matrix. Radionuclide release from the vault in the unsaturated conditions after closure of the repository and consequent contaminant plume transport has been assessed taking into account site-specific natural and engineering conditions and based on a normal evolution scenario. The highest peak radionuclide activity concentrations were estimated applying the FEFLOW code. The highest value of {sup 14}C activity concentration(about 1.3x10{sup 8} Bq/m{sup 3}) at the groundwater table

Thermal Management and Analysis for a Potential Yucca Mountain Repository

International Nuclear Information System (INIS)

Dr. A. Van Luik

2004-01-01

In the current Yucca Mountain repository design concept, heat from the emplaced waste (mostly from spent nuclear fuel) would keep the temperature of the rock around the waste packages higher than the boiling point of water for hundreds to thousands of years after the repository is closed. The design concept allows below-boiling portions of the pillars between drifts to serve as pathways for the drainage of thermally mobilized water and percolating groundwater by limiting the distance that boiling temperatures extend into the surrounding rock. This design concept takes advantage of host rock dry out, which would create a dry environment within the emplacement drifts and reduce the amount of water that might otherwise be available to enter the drifts and contact the waste packages during this thermal pulse. Table 1 provides an overview of design constraints related to thermal management after repository closure. The Yucca Mountain repository design concept also provides flexibility to allow for operation over a range of lower thermal operating conditions. The thermal conditions within the emplacement drifts can be varied, along with the relative humidity, by modifying operational parameters such as the thermal output of the waste packages, the spacing of the waste packages in the emplacement drifts, and the duration and rate of active and passive ventilation. A lower range has been examined to quantify lower-temperature thermal conditions (temperatures and associated humidity conditions) in the emplacement drifts and to quantify impacts to the required emplacement area and excavated drift length. This information has been used to evaluate the potential long-term performance of a lower-temperature repository and to estimate the increase in costs associated with operating a lower-temperature repository. This presentation provides an overview of the thermal management evaluations that have been conducted to investigate a range of repository thermal conditions and

Foreign materials in a deep repository for spent nuclear fuels

International Nuclear Information System (INIS)

Jones, C.; Christiansson, Aa.; Wiborgh, M.

1999-12-01

The effects of foreign substances introduced into a spent-fuel repository are reviewed. Possible impacts on processes and barrier-functions are examined, and the following areas are identified: Corrosion of the spent-fuel canister through the presence of sulfur and substances that favor microbial growth; impacts on the bentonite properties through the presence of cations as calcium, potassium and iron; radionuclide transport through the presence of complex-formers and surface-active substances

Nuclear waste repository design and construction

International Nuclear Information System (INIS)

Bohlke, B.M.; Monsees, J.E.

1987-01-01

Extensive underground excavation will be required for construction of a mined geologic repository for nuclear waste. Hundreds of thousands of feet of drift will be required based on the conceptual layout design for each candidate nuclear waste repository. Comparison of boring and blasting excavation methods are discussed, as are special design and construction requirements (e.g., quality assurance procedures and performance assessment) for the nuclear waste repository. Comparisons are made between boring and blasting construction methods for the repository designs proposed for salt, volcanic tuff, and basalt

Release consequence analysis for a hypothetical geologic radioactive waste repository in salt

International Nuclear Information System (INIS)

1979-08-01

One subtask conducted under the INFCE program is to evaluate and compare the health and safety impacts of different fuel cycles in which all radioactive wastes (except those from mining and milling) are placed in a geologic repository in salt. To achieve this objective, INFCE Working Group 7 examined the radiologic dose to humans from geologic repositories containing waste arisings as defined for seven reference fuel cycles. This report examines the release consequences for a generic waste repository in bedded salt. The top of the salt formation and the top of the repository are assumed to be 250 and 600 m, respectively, below the surface. The hydrogeologic structure above the salt consists of two aquifers and two aquitards. The aquifers connect to a river 6.2 km from the repository. The regional gradient to the river is 1 m/km in all aquifers. Hydrologic, transport, and dose models were used to model two release scenarios for each fuel cycle, one without a major disturbance and one in which a major geologic perturbation breached the repository immediately after it was sealed. The purpose of the modeling was to predict the rate of transport of radioactive contaminants from the repository through the geosphere to the biosphere, and to determine the potential dose to humans. Of the many radionuclides in the waste, only 129 I and 226 Ra arrived at the river in sufficient concentrations for a measurable dose calculation. Radionuclide concentrations in the ground water pose no threat to man because the ground water is a concentrated brine and it is diluted by a factor of 10 6 to 10 7 upon entering the river

Impact of Drill and Blast Excavation on Repository Performance Confirmation

International Nuclear Information System (INIS)

Keller, R.; Francis, N.; Houseworth, J.; Kramer, N.

2000-01-01

There has been considerable work accomplished internationally examining the effects of drill and blast excavation on rock masses surrounding emplacement openings of proposed nuclear waste repositories. However, there has been limited discussion tying the previous work to performance confirmation models such as those proposed for Yucca Mountain, Nevada. This paper addresses a possible approach to joining the available information on drill and blast excavation and performance confirmation. The method for coupling rock damage data from drill and blast models to performance assessment models for fracture flow requires a correlation representing the functional relationship between the peak particle velocity (PPV) vibration levels and the potential properties that govern water flow rates in the host rock. Fracture aperture and frequency are the rock properties which may be most influenced by drill and blast induced vibration. If it can be shown (using an appropriate blasting model simulation) that the effect of blasting is far removed from the waste package in an emplacement drift, then disturbance to the host rock induced in the process of drill and blast excavation may be reasonably ignored in performance assessment calculations. This paper proposes that the CANMET (Canada Center for Mineral and Energy Technology) Criterion, based on properties that determine rock strength, may be used to define a minimum PPV. This PPV can be used to delineate the extent of blast induced damage. Initial applications have demonstrated that blasting models can successfully be coupled with this criterion to predict blast damage surrounding underground openings. The Exploratory Studies Facility at Yucca Mountain has used a blasting model to generate meaningful estimates of near-field vibration levels and damage envelopes correlating to data collected from pre-existing studies conducted. Further work is underway to expand this application over a statistical distribution of geologic

Nevada potential repository preliminary transportation strategy Study 2. Volume 1

International Nuclear Information System (INIS)

1996-02-01

The objectives of this study were to build on the findings of the Nevada Potential Repository Preliminary Transportation Strategy Study 1 (CRWMS M ampersand O 1995b), and to provide additional information for input to the repository environmental impact statement (EIS) process. In addition, this study supported the future selection of a preferred rail corridor and/or heavy haul route based on defensible data, methods, and analyses. Study research did not consider proposed legislation. Planning was conducted according to the Civilian Radioactive Waste Management Program Plan (DOE 1994a). The specific objectives of Study 2 were to: eliminate or reduce data gaps, inconsistencies, and uncertainties, and strengthen the analysis performed in Study 1; develop a preliminary list of rail route evaluation criteria that could be used to solicit input from stakeholders during scoping meetings. The evaluation criteria will be revised based on comments received during scoping; restrict and refine the width of the four rail corridors identified in Study 1 to five miles or less, based on land use constraints and engineering criteria identified and established in Study 2; evaluate national-level effects of routing spent nuclear fuel and high-level waste to the four identified branch lines, including the effects of routing through or avoiding Las Vegas; continue to gather published land use information and environmental data to support the repository EIS; continue to evaluate heavy haul truck transport over three existing routes as an alternative to rail and provide sufficient information to support the repository EIS process; and evaluate secondary uses for rail (passenger use, repository construction, shared use)

National radioactive wasterRepository Mochovce

International Nuclear Information System (INIS)

2000-01-01

In this leaflet the scheme of the Mochovce National radioactive waste repository for the Slovak Republic is presented. The National radioactive waste repository in Mochovce is a surface type storage facility. It is intended for final disposal of solid and solidified low and intermediate radioactive waste produced during the operation of nuclear power plants and institutions located within the territory of the Slovak Republic. The Repository site is situated about 2 km northwest to the Mochovce NPP

Effect of reprocessing and recycling on the geologic repository dose rate : status

International Nuclear Information System (INIS)

Morris, E. E.; Nutt, W. M.; Wigeland, R. A.; Nuclear Engineering Division

2007-01-01

Two simplified repository performance assessment models are used to assess the impact of modeling changes in on conclusions regarding the impact of various reprocessing and recycling strategies. Waste streams from a pressurized water reactor (PWR) and a preliminary design for an advanced burner test reactor (ABTR) are used for this study of the effects on the estimated dose rate resulting from the release of radionuclides from a geologic repository. Calculations for the PWR make use of radionuclide discharge vectors for an assumed burnup of 51 GWd/MTIHM[1]. The repository is assumed to be filled with 70,000 MT of the spent fuel or with a glass waste form containing the radionuclides from 70,000 MT of spent PWR fuel. For the ABTR, the radionuclide inventory discharged at the end of an equilibrium cycle[2] is processed into a glass waste form for repository disposal, assuming actinide recovery efficiencies ranging from 90% to 99.99%. The recovered actinides are returned to the reactor. To compare with the PWR results, the repository is assumed to be filled with ABTR waste from fuel that has generated the same amount of thermal energy as 70,000 MT of the PWR fuel. The two repository performance assessment models, the first a simplified model[3] (SSR) based on the site recommendation model used by the Yucca Mountain Project (YMP)[4], and the second an updated simplified model (US) based on more recent modeling developments by the YMP are implemented in the computer simulation code GoldSim[5]. The updated model is based on a simplified model used to conduct a sensitivity analysis to evaluate factors that potentially influence performance of a repository at Yucca Mountain over the period of peak dose[6]. Factors that have either a minor or no effect on the peak dose either were not included in that simplified model or were included in a bounding representation. In the US model, enhancements were made to include some factors that have an effect on the dose occurring

Biological Web Service Repositories Review.

Science.gov (United States)

Urdidiales-Nieto, David; Navas-Delgado, Ismael; Aldana-Montes, José F

2017-05-01

Web services play a key role in bioinformatics enabling the integration of database access and analysis of algorithms. However, Web service repositories do not usually publish information on the changes made to their registered Web services. Dynamism is directly related to the changes in the repositories (services registered or unregistered) and at service level (annotation changes). Thus, users, software clients or workflow based approaches lack enough relevant information to decide when they should review or re-execute a Web service or workflow to get updated or improved results. The dynamism of the repository could be a measure for workflow developers to re-check service availability and annotation changes in the services of interest to them. This paper presents a review on the most well-known Web service repositories in the life sciences including an analysis of their dynamism. Freshness is introduced in this paper, and has been used as the measure for the dynamism of these repositories. © 2017 The Authors. Published by Wiley-VCH Verlag GmbH & Co. KGaA.

Uncertainty management in radioactive waste repository site assessment

International Nuclear Information System (INIS)

Baldwin, J.f.; Martin, T.P.; Tocatlidou

1994-01-01

The problem of performance assessment of a site to serve as a repository for the final disposal of radioactive waste involves different types of uncertainties. Their main sources include the large temporal and spatial considerations over which safety of the system has to be ensured, our inability to completely understand and describe a very complex structure such as the repository system, lack of precision in the measured information etc. These issues underlie most of the problems faced when rigid probabilistic approaches are used. Nevertheless a framework is needed, that would allow for an optimal aggregation of the available knowledge and an efficient management of the various types of uncertainty involved. In this work a knowledge-based modelling of the repository selection process is proposed that through a consequence analysis, evaluates the potential impact that hypothetical scenarios will have on a candidate site. The model is organised around a hierarchical structure, relating the scenarios with the possible events and processes that characterise them, and the site parameters. The scheme provides for both crisp and fuzzy parameter values and uses fuzzy semantic unification and evidential support logic reference mechanisms. It is implemented using the artificial intelligence language FRIL and the interaction with the user is performed through a windows interface

IAEA safeguards for geological repositories

International Nuclear Information System (INIS)

Moran, B.W.

2005-01-01

In September. 1988, the IAEA held its first formal meeting on the safeguards requirements for the final disposal of spent fuel and nuclear material-bearing waste. The consensus recommendation of the 43 participants from 18 countries at this Advisory Group Meeting was that safeguards should not terminate of spent fuel even after emplacement in, and closure of, a geologic repository.' As a result of this recommendation, the IAEA initiated a series of consultants' meetings and the SAGOR Programme (Programme for the Development of Safeguards for the Final Disposal of Spent Fuel in Geologic Repositories) to develop an approach that would permit IAEA safeguards to verify the non-diversion of spent fuel from a geologic repository. At the end of this process, in December 1997, a second Advisory Group Meeting, endorsed the generic safeguards approach developed by the SAGOR Programme. Using the SAGOR Programme results and consultants' meeting recommendations, the IAEA Department of Safeguards issued a safeguards policy paper stating the requirements for IAEA safeguards at geologic repositories. Following approval of the safeguards policy and the generic safeguards approach, the Geologic Repository Safeguards Experts Group was established to make recommendations on implementing the safeguards approach. This experts' group is currently making recommendations to the IAEA regarding the safeguards activities to be conducted with respect to Finland's repository programme. (author)

Radioactive wastes repository in Temascalapa, State of Mexico, public opinion. Determination of health effects

International Nuclear Information System (INIS)

Solis Tinoco, E.

1998-01-01

Nuclear waste usually concerns public about the impact on public health and the environment. In Mexico, such interest exists, particularly in the Temascalapa Municipality, Mexico where a low level waste repository recognized by the IAEA, has been functioning since 1972. Maquixco repository is located at 42 Kilometers northeast of Mexico City. Although the environmental radiological monitoring records have demonstrated negligible impact on the environment, in 1998 an unusual public polemic on radioactive health effects appeared among Temascalapa residents. This paper presents a research performed during 1998 with the participation of the National Nuclear Research Institute of Mexico and the National Autonomous University of Mexico. The research design allowed the involvement of local authorities, as a way of stimulate public participation. The research was performed in nine locations of the Temascalapa Municipality, it was focused on public polemics, associated to Maquixco repository as well as trying to identify demographic factors that exert influence on public attitudes. There are also presented the results of personal dosimetry analysis performed on a four hundred residents sample of this Municipality. (Author)

Safety performance of a near surface repository subject to a fuel burning

International Nuclear Information System (INIS)

Stefanini, Lorenzo; Frano, Rosa Lo; Forasassi, Giuseppe

2015-01-01

This study aims to investigate the performances of a near surface repository subject to fuel burning occurring simultaneously or subsequently to a large commercial aircraft impact. Specifically the thermal effects caused by a Boeing-747 crushing (considered like “beyond design basis accident”) are studied. An important part of this study is the analysis of the possible (thermo-mechanical) degradation effects, as dehydration, degasification, pressurization, etc. that the concrete may undergo, particularly in the case of prolonged fire, and of the resistance of structure itself in this condition. Conservative assumptions and restrictions have been made with regard to the fire scenario, the maximum temperature of which is calculated on the basis of the fuel airplane amount, the normal impact, the variation of the material properties along with the temperature as well the damaging phenomena of concrete. The airplane impact load, calculated with the Riera approach, and the maximum temperature, reached during the fuel combustion, are used as input (boundary condition) in the numerical simulations performed by MARC© code. The obtained results showed that a repository wall thickness, ranging from 0.6 to 0.9 m, is not sufficient to prevent the local penetration of wall. To reduce the computational cost, the analyses have been made only on a half part of the structure, highlighting the dominance of thermal effects. Despite the ongoing concrete degradation phenomena, the overall integrity of the repository seemed to be guaranteed as well as the containment and the confinement of radioactive waste. (author)

Nuclear waste repository siting and locational conflict analysis: A contextual approach

International Nuclear Information System (INIS)

Murauskas, G.T.

1989-01-01

This study develops and evaluates an alternative framework that is based on contextual variables. The premise is that differences in attitudes and perceptions regarding the local siting of nuclear wastes and differences in attitudes regarding siting decision-making procedures are influenced by local political, economic, and cultural variables. This framework articulates the nature of conflict in terms of the incongruence between the use-value individuals ascribe to their present situation and the anticipated exchange-value individuals associate with the local siting of a nuclear waste repository. In order to evaluate this conceptual framework a survey was conducted of residents in four communities representing distinct societal contexts: Richton, Mississippi; Peterborough, New Hampshire; Richland, Washington; and Antigo/Waupaca, Wisconsin. Data analyses indicate substantial differences in economic expectations associated with the local siting of a high-level nuclear waste repository and in perception regarding the impacts such a repository might have on the environment, local agriculture, personal health and safety, and the quality of life

Evaluation of the Overall Costs for the Croatian Repository: Varying Site, Design and Financial Parameters

International Nuclear Information System (INIS)

Kucar-Dragicevic, S.; Subasic, D.; Lebegner, J.

2000-01-01

Preliminary preparations for the construction of a LILW repository in Croatia included a number of activities and projects related to the siting process, safety assessment, disposal technology and repository design, and public acceptance issues. Costs evaluations have always been a part of the developing project documentation. However, only the estimates of the facility construction and equipment acquisition costs had been included, while other costs associated with the project development and management have not been considered up to now. For the first time the infrastructure status at the potential sites has been evaluated, and the costs of the repository operations as well as the post-closure management has been estimated. Cost parameters have been considered from both technical and fiscal points of view, comparing their relative influence on the overall repository costs. Assessment of the total project costs in eight cases for the four preferential sites and two repository designs gave a clearer picture of the development and management costs differences for the considered options. Without considerations of the operational and post-operational repository management expenses, the total project costs appear to have been heavily underestimated. Also, while the construction costs for the tunnel and the surface type repositories are significantly different, this influence of the repository type on the total project costs becomes far less important when the later phases management expenses are added. Finally, the role of fiscal parameters may further diminish the site and technology impacts on the overall costs. (author)

Radiological consequence analysis of a repository for radioactive waste

International Nuclear Information System (INIS)

Fitzpatrick, J.; Buchheim, B.; Hoop, F.J.

1982-01-01

One of the methods under consideration for the disposal of radioactive wastes is emplacement in a repository within deep, continental formations. This paper presents the experience gained in developing a methodology to make an assessment of the radiological consequences both for normal operation and for possible accident situations for a specific repository design in a salt dome at Gorleben in Germany , designed to accommodate all categories of radioactive waste. Radionuclide release scenarios were derived from a systematic analysis of the facility design and proposed operational procedure. Where necessary simple numerical models for such topics as direct radiation exposure from waste containers, release and transport of radionuclides, radiolysis, heat transfer, creep and impact were developed to give a first estimate of the radiological consequences due to radionuclide releases. (author)

Thermo-hydro-mechanical processes in the nearfield around a HLW repository in argillaceous formations. Vol. I. Laboratory investigations

Energy Technology Data Exchange (ETDEWEB)

Zhang, Chun-Liang; Czaikowski, Oliver; Rothfuchs, Tilmann; Wieczorek, Klaus

2013-06-15

All over the world, clay formations are being investigated as host medium for geologic disposal of radioactive waste because of their favourable properties, such as very low hydraulic conductivity against fluid transport, good sorption capacity for retardation of radionuclides, and high potential of self-sealing of fractures. The construction of a repository, the disposal of heat-emitting high-level radioactive waste (HLW), the backfilling and sealing of the remaining voids, however, will inevitably induce mechanical (M), hydraulic (H), thermal (T) and chemical (C) disturbances to the host formation and the engineered barrier system (EBS) over very long periods of time during the operation and post-closure phases of the repository. The responses and resulting property changes of the clay host rock and engineered barriers are to be well understood, characterized, and predicted for assessing the long-term performance and safety of the repository.

Repository site characterization

International Nuclear Information System (INIS)

Voss, J.W.; Pentz, D.L.

1987-01-01

The characterization of candidate repository sites has a number of programmatic objectives. Principal among these is the acquisition of data: a) to determine the suitability of a site relative to the DOE repository siting guidelines, b) to support model development and calculations to determine the suitability of a site relative to the post closure criteria of the NRC and EPA, c) to support the design of a disposal system, including the waste package and the engineered barrier system, as well as the shafts and underground openings of the repository. In meeting the gaols of site characterization, the authors have an obligation to conduct their investigations within an appropriate budget and schedule. This mandates that a well-constructed and systematic plan for field investigations be developed. Such a plan must fully account for the mechanisms which will control the radiologic performance in the repository. The plan must also flexibly and dynamically respond to the results of each step of field investigation, responding to the spatial variability of earth as well as to enhanced understandings of the performance of the disposal system. Such a plan must ensure that sufficient data are available to support the necessary probabilistic calculations of performance. This paper explores the planning for field data acquisition with specific reference to requirements for demonstrations of the acceptable performance for disposal systems

The preliminary design and feasibility study of the spent fuel and high level waste repository in the Czech Republic

International Nuclear Information System (INIS)

Valvoda, Z.; Holub, J.; Kucerka, M.

1996-01-01

In the year 1993, began the Program of Development of the Spent Fuel and High Level Waste Repository in the Conditions of the Czech Republic. During the first phase, the basic concept and structure of the Program has been developed, and the basic design criteria and requirements were prepared. In the conditions of the Czech Republic, only an underground repository in deep geological formation is acceptable. Expected depth is between 500 to 1000 meters and as host rock will be granites. A preliminary variant design study was realized in 1994, that analyzed the radioactive waste and spent fuel flow from NPPs to the repository, various possibilities of transportation in accordance to the various concepts of spent fuel conditioning and transportation to the underground structures. Conditioning and encapsulation of spent fuel and/or radioactive waste is proposed on the repository site. Underground disposal structures are proposed at one underground floor. The repository will have reserve capacity for radioactive waste from NPPs decommissioning and for waste non acceptable to other repositories. Vertical disposal of unshielded canisters in boreholes and/or horizontal disposal of shielded canisters is studied. As the base term of the start up of the repository operation, the year 2035 has been established. From this date, a preliminary time schedule of the Project has been developed. A method of calculating leveled and discounted costs within the repository lifetime, for each of selected 5 variants, was used for economic calculations. Preliminary expected parametric costs of the repository are about 0,1 Kc ($0.004) per MWh, produced in the Czech NPPs. In 1995, the design and feasibility study has gone in more details to the technical concept of repository construction and proposed technologies, as well as to the operational phase of the repository. Paper will describe results of the 1995 design work and will present the program of the repository development in next period

An environmental impact measure for nuclear fuel cycle evaluation

International Nuclear Information System (INIS)

Ahn, Joonhong

2004-01-01

Review of the models and measures for repository performance assessment has revealed that dedicated measures for environmental impacts need to be developed for the purpose of nuclear-fuel-cycle evaluation from the viewpoint of environmental impact minimization. The present study proposes the total toxicity index of released radionuclides that have accumulated in the region exterior to the repository as an environmental impact measure. The measure is quantitatively evaluated by a radionuclide transport model that incorporates the effects of canister-array configuration and the initial mass loading in the waste canister. With the measure, it is demonstrated that the environmental impact of the repository can be effectively reduced by reduction of the initial mass loading and change in the canister-array configuration in the repository. Environmental impacts of the mill tailings and the depleted uranium are as important as those from the high-level radioactive wastes repository. For a fair comparison of various fuel cycles, the sum of these impacts should be compared. (author)

Gas generation in repositories

International Nuclear Information System (INIS)

Biddle, P.; Rees, J.H.; McGahan, D.; Rushbrook, P.E.

1987-09-01

The nature and quantities of gases likely to be produced by various processes in repositories for low level and intermediate level radioactive wastes are examined in this preliminary study. Many simplifying assumptions are made where published or experimental data is unavailable. The corrosion of the canisters and metallic components in wastes is likely to be the major gas production process in both types of repository. A significant contribution from microbiological activity is expected to occur in low level repositories, predominantly where no cement grouting of the cans has been carried out. A number of areas for further research, required before a more comprehensive study could be carried out, have been identified. (author)

SUBSURFACE REPOSITORY INTEGRATED CONTROL SYSTEM DESIGN

International Nuclear Information System (INIS)

Randle, D.C.

2000-01-01

The primary purpose of this document is to develop a preliminary high-level functional and physical control system architecture for the potential repository at Yucca Mountain. This document outlines an overall control system concept that encompasses and integrates the many diverse process and communication systems being developed for the subsurface repository design. This document presents integrated design concepts for monitoring and controlling the diverse set of subsurface operations. The Subsurface Repository Integrated Control System design will be composed of a series of diverse process systems and communication networks. The subsurface repository design contains many systems related to instrumentation and control (I andC) for both repository development and waste emplacement operations. These systems include waste emplacement, waste retrieval, ventilation, radiological and air monitoring, rail transportation, construction development, utility systems (electrical, lighting, water, compressed air, etc.), fire protection, backfill emplacement, and performance confirmation. Each of these systems involves some level of I andC and will typically be integrated over a data communications network throughout the subsurface facility. The subsurface I andC systems will also interface with multiple surface-based systems such as site operations, rail transportation, security and safeguards, and electrical/piped utilities. In addition to the I andC systems, the subsurface repository design also contains systems related to voice and video communications. The components for each of these systems will be distributed and linked over voice and video communication networks throughout the subsurface facility. The scope and primary objectives of this design analysis are to: (1) Identify preliminary system-level functions and interfaces (Section 6.2). (2) Examine the overall system complexity and determine how and on what levels the engineered process systems will be monitored

Preliminary design of the repository. Stage 2

International Nuclear Information System (INIS)

Saanio, T.; Kirkkomaeki, T.; Keto, P.; Kukkola, T.; Raiko, H.

2007-04-01

Spent nuclear fuel from Finnish nuclear power plants will be disposed of in deep bedrock in Olkiluoto, Eurajoki. The repository is planned to be excavated at a depth of 400 - 500 metres. Access routes to the repository include a 1:10 inclined access tunnel, and vertical shafts. The fuel is encapsulated in the encapsulation plant above ground and transferred to the repository in the canister lift. Deposition tunnels, central tunnels and technical rooms are excavated at the disposal level. The canisters are deposited in deposition holes that are covered with bentonite blocks. The deposition holes are bored in the floors of the deposition tunnels. The central tunnel system consists of two parallel central tunnels that are inter-connected at certain distances. Two parallel central tunnels improve the fire safety of the rooms and also allow flexible backfilling and closing of the deposition tunnels in stages at the operational phase of the repository. An underground rock characterization facility, ONKALO, is excavated at the disposal level to support and confirm investigations carried out from above ground. ONKALO is designed so that it can later serve as part of the repository. ONKALO excavations were started in 2004. The repository will be excavated in the 2010s and operation will start in 2020. The fifth nuclear power unit makes the operational phase of the repository very long. Parts of the repository will be excavated and closed over the long operational period. The repository can be constructed at one or several levels. The one-storey alternative is the so-called reference alternative in this preliminary design report. The two-storey alternative is also taken into account in the ONKALO designs. The preliminary designs of the repository are presented as located in Olkiluoto. The location of the repository will be revised when more information on the bedrock has been gained. More detailed data of the circumstances will be obtained from above ground investigations

Preliminary design of the repository, stage 2

International Nuclear Information System (INIS)

Saanio, T.; Kirkkomaeki, T.; Keto, P.; Kukkola, T.; Raiko, H.

2007-01-01

Spent nuclear fuel from Finnish nuclear power plants will be disposed of in deep bedrock in Olkiluoto, Eurajoki. The repository is planned to be excavated at a depth of 400 - 500 metres. Access routes to the repository include a 1:10 inclined access tunnel, and vertical shafts. The fuel is encapsulated in the encapsulation plant above ground and transferred to the repository in the canister lift. Deposition tunnels, central tunnels and technical rooms are excavated at the disposal level. The canisters are deposited in deposition holes that are covered with bentonite blocks. The deposition holes are bored in the floors of the deposition tunnels. The central tunnel system consists of two parallel central tunnels that are inter-connected at certain distances. Two parallel central tunnels improve the fire safety of the rooms and also allow flexible backfilling and closing of the deposition tunnels in stages at the operational phase of the repository. An underground rock characterization facility, ONKALO, is excavated at the disposal level to support and confirm investigations carried out from above ground. ONKALO is designed so that it can later serve as part of the repository. ONKALO excavations were started in 2004. The repository will be excavated in the 2010s and operation will start in 2020. The fifth nuclear power unit makes the operational phase of the repository very long. Parts of the repository will be excavated and closed over the long operational period. The repository can be constructed at one or several levels. The one-storey alternative is the so-called reference alternative in this preliminary design report. The two-storey alternative is also taken into account in the ONKALO designs. The preliminary designs of the repository are presented as located in Olkiluoto. The location of the repository will be revised when more information on the bedrock has been gained. More detailed data of the circumstances will be obtained from above ground investigations

Nuclear waste repository siting

International Nuclear Information System (INIS)

Soloman, B.D.; Cameron, D.M.

1987-01-01

This paper discusses the geopolitics of nuclear waste disposal in the USA. Constitutional choice and social equity perspectives are used to argue for a more open and just repository siting program. The authors assert that every potential repository site inevitably contains geologic, environmental or other imperfections and that the political process is the correct one for determining sites selected

Granite-repository - geochemical environment

International Nuclear Information System (INIS)

1979-04-01

Some geochemical data of importance for a radioactive waste repository in hard rock are reviewed. The ground water composition at depth is assessed. The ground water chemistry in the vicinity of uranium ores is discussed. The redox system in Swedish bedrock is described. Influences of extreme climatic changes and of repository mining and construction are also evaluated

Workshop: Creating Your Institutional Research Repository

KAUST Repository

Grenz, Daryl M.

2016-11-08

In 2002, the Scholarly Publishing and Academic Resources Coalition (SPARC) proposed the concept of an institutional repository to simultaneously disrupt and enhance the state of scholarly communications in the academic world. Thirteen years later, thousands of universities and other institutions have answered this call, but many more have not due to gaps in budgets, awareness and, most of all, practical guidance on creating an institutional repository. This workshop provides you with an essential primer on what it takes to establish a fully-functioning institutional repository. Every aspect of the process will be covered, including policies, procedures, staffing guidelines, workflows and repository technologies.

Performance of high level waste forms and engineered barriers under repository conditions

International Nuclear Information System (INIS)

1991-02-01

The IAEA initiated in 1977 a co-ordinated research programme on the ''Evaluation of Solidified High-Level Waste Forms'' which was terminated in 1983. As there was a continuing need for international collaboration in research on solidified high-level waste form and spent fuel, the IAEA initiated a new programme in 1984. The new programme, besides including spent fuel and SYNROC, also placed greater emphasis on the effect of the engineered barriers of future repositories on the properties of the waste form. These engineered barriers included containers, overpacks, buffer and backfill materials etc. as components of the ''near-field'' of the repository. The Co-ordinated Research Programme on the Performance of High-Level Waste Forms and Engineered Barriers Under Repository Conditions had the objectives of promoting the exchange of information on the experience gained by different Member States in experimental performance data and technical model evaluation of solidified high level waste forms, components of the waste package and the complete waste management system under conditions relevant to final repository disposal. The programme includes studies on both irradiated spent fuel and glass and ceramic forms as the final solidified waste forms. The following topics were discussed: Leaching of vitrified high-level wastes, modelling of glass behaviour in clay, salt and granite repositories, environmental impacts of radionuclide release, synroc use for high--level waste solidification, leachate-rock interactions, spent fuel disposal in deep geologic repositories and radionuclide release mechanisms from various fuel types, radiolysis and selective leaching correlated with matrix alteration. Refs, figs and tabs

Final repository for spent nuclear fuel. Underground design Simpevarp, Layout D1

Energy Technology Data Exchange (ETDEWEB)

NONE

2006-04-15

4,500. However, in order to accommodate the uncertainty entailed by possible future extensions of the operating periods of the nuclear power plants, the deposition area should, according to SKB, be designed for a capacity of 6,000 canisters. The strategy for answering the question 'Can the repository be accommodated within the assigned area' is to build an appropriate risk model. The most important results obtained from the calculations are: There is a very high (> 99%) probability that 6,000 canisters can be accommodated within the studied area at a depth of 500 m. Total deposition hole loss is 13% on average. The average area needed to host the 6,000 canisters at a depth of 500 m is 3.5 km{sup 2}, with a range of 2-5.6 km{sup 2}. This is within the limits of what was found in the layout studies in Chapter 5, where an area of 4.5 km{sup 2} was found to be needed. It should be noted that the layout study was not optimized. The three factors that have the greatest impact on uncertainty are: Hole spacing due to thermal properties; Loss percentage due to fractures with R > 100 m; and Dip of external boundary deformation zone.

Safeguards for geological repositories

International Nuclear Information System (INIS)

Fattah, A.

2000-01-01

Direct disposal of spent nuclear fuel in geological repositories is a recognised option for closing nuclear fuel cycles. Geological repositories are at present in stages of development in a number of countries and are expected to be built and operated early next century. A State usually has an obligation to safely store any nuclear material, which is considered unsuitable to re-enter the nuclear fuel cycle, isolated from the biosphere. In conjunction with this, physical protection has to be accounted for to prevent inadvertent access to such material. In addition to these two criteria - which are fully under the State's jurisdiction - a third criterion reflecting international non-proliferation commitments needs to be addressed. Under comprehensive safeguards agreements a State concedes verification of nuclear material for safeguards purposes to the IAEA. The Agency can thus provide assurance to the international community that such nuclear material has been used for peaceful purposes only as declared by the State. It must be emphasised that all three criteria mentioned constitute a 'unit'. None can be sacrificed for the sake of the other, but compromises may have to be sought in order to make their combination as effective as possible. Based on comprehensive safeguards agreements signed and ratified by the State, safeguards can be terminated only when the material has been consumed or diluted in such a way that it can no longer be utilised for any nuclear activities or has become practicably irrecoverable. As such safeguards for nuclear material in geological repositories have to be continued even after the repository has been back-filled and sealed. The effective application of safeguards must assure continuity-of-knowledge that the nuclear material in the repository has not been diverted for an unknown purpose. The nuclear material disposed in a geological repository may eventually have a higher and long term proliferation risk because the inventory is

The status of radioactive waste repository development in the United States - December 2011

International Nuclear Information System (INIS)

Hill, David R.

2012-01-01

The current state of affairs concerning development in the United States of a permanent repository for disposal of spent nuclear fuel (SNF) and high-level radioactive waste (HLW) is, in a word, uncertain. The President of the United States has asserted that he believes licensing and development of the Yucca Mountain repository should be abandoned, while other important parties believe licensing and development should continue. And not surprisingly, there is a disagreement as to what the law requires and whether the licensing process for the Yucca Mountain repository can be terminated at this point, even if the President would like for that to happen. The future of Yucca Mountain, and the future of radioactive waste disposal in the United States generally, currently are pending before the US Court of Appeals for the District of Columbia Circuit, and eventually the Supreme Court of the United States may decide some of the important legal issues concerning Yucca Mountain's future. The November 2012 US elections also likely will have a significant impact on future radioactive waste repository development

Radioactive Waste Repositories Administration - SURAO

International Nuclear Information System (INIS)

Kucerka, M.

1998-01-01

The Atomic Act specifies, among other things, responsibilities of the government in the field of safe disposal of radioactive wastes. To satisfy this responsibility, the Ministry of Industry and Trade has established the Radioactive Waste Repositories Administration (SURAO). SURAO's major responsibilities include: (a) the preparation, construction, commissioning, operation, and decommissioning of radioactive waste repositories and the monitoring of their environmental impacts; (b) radioactive waste management; (c) spent or irradiated nuclear fuel processing into a form suitable for storage/disposal or reuse; (d) record-keeping of received radioactive wastes and their producers; (e) administration of fund transfers as stipulated by the Atomic Act, Article 27; (f) development of proposals for specification of fees to be paid to the Nuclear Account; (g) responsibility for and coordination of research and development in the field of radioactive waste handling and management; (h) supervision of licensees' margin earmarked for the decommissioning of their facilities; (i) providing services in radioactive waste handling and management; (j) handling and management of radioactive wastes that have been transferred to the Czech Republic from abroad and cannot be sent back; (k) interim administration of radioactive wastes that have become state property. The Statute of the Administration is reproduced in full. (P.A.)

Uncertainty: a discriminator for above and below boiling repository design decisions

International Nuclear Information System (INIS)

Wilder, D G; Lin, W; Buscheck, T A; Wolery, T J; Francis, N D

2000-01-01

The US nuclear waste disposal program is evaluating the Yucca Mountain (YM) site for possible disposal of nuclear waste. Radioactive decay of the waste, particularly spent fuel, generates sufficient heat to significantly raise repository temperatures. Environmental conditions in the repository system evolve in response to this heat. The amount of temperature increase, and thus environmental changes, depends on repository design and operations. Because the evolving environment cannot be directly measured until after waste is emplaced, licensing decisions must be based upon model and analytical projections of the environmental conditions. These analyses have inherent uncertainties. There is concern that elevated temperatures increase uncertainty, because most chemical reaction rates increase with temperature and boiling introduces additional complexity of vapor phase reactions and transport. This concern was expressed by the NWTRB, particularly for above boiling temperatures. They state that ''the cooler the repository, the lower the uncertainty about heat-driven water migration and the better the performance of waste package materials. Above this temperature, technical uncertainties tend to be significantly higher than those associated with below-boiling conditions.'' (Cohon 1999). However, not all uncertainties are reduced by lower temperatures, indeed some may even be increased. This paper addresses impacts of temperatures on uncertainties

Beyond a complete failure : The impact of partial capacity reductions on public transport network vulnerability

NARCIS (Netherlands)

Cats, O.; Jenelius, E.

2015-01-01

Disruptions often result with partial capacity reduction without resulting with a complete breakdown. This study aims to move beyond the analysis of complete failure by investigating the impacts of partial capacity reduction on public transport network performance. We analyse the relation between

Modelling saline intrusion for repository performance assessment

International Nuclear Information System (INIS)

Jackson, C.P.

1989-04-01

UK Nirex Ltd are currently considering the possibility of disposal of radioactive waste by burial in deep underground repositories. The natural pathway for radionuclides from such a repository to return to Man's immediate environment (the biosphere) is via groundwater. Thus analyses of the groundwater flow in the neighbourhood of a possible repository, and consequent radionuclide transport form an important part of a performance assessment for a repository. Some of the areas in the UK that might be considered as possible locations for a repository are near the coast. If a repository is located in a coastal region seawater may intrude into the groundwater flow system. As seawater is denser than fresh water buoyancy forces acting on the intruding saline water may have significant effects on the groundwater flow system, and consequently on the time for radionuclides to return to the biosphere. Further, the chemistry of the repository near-field may be strongly influenced by the salinity of the groundwater. It is therefore important for Nirex to have a capability for reliably modelling saline intrusion to an appropriate degree of accuracy in order to make performance assessments for a repository in a coastal region. This report describes work undertaken in the Nirex Research programme to provide such a capability. (author)

Analisis Konten dan Kebijakan Akses Institutional Repository

Directory of Open Access Journals (Sweden)

Amirul Ulum

2016-07-01

Abstract; Institutional repository has become a major concern of higher education in Indonesia. The number of institutional respository was increased, one of the reason is the ranking web of repositories has been conducted by the Cybermetrics Lab in 2008. At that time, many institutions started to build institutional repository in order to manage the scientific work and also trying to reach the better ranks. Meanwhile, it is an achievement of institution performance which can be promote and increase visibility for the institution. University of Surabaya has also developed the institutional repository and managed by the library. The aims of this study is to analyze the content availability and access policies defined by the University of Surabaya repository  providing services to the academic community and external users. The method used in this study by using observations of the institutional repository University of Surabaya with a literature review to clarify the analysis of the content and access policies. The results of this study indicate that the library's role is has the authority to manage the scientific work of academic community can be done through the institutional repository. However there is still need for library to be proactive to communicate regulations on mandatory deposit of scientific work and create intensive promotion of the institutional repository.

Lithophysal Rock Mass Mechanical Properties of the Repository Host Horizon

International Nuclear Information System (INIS)

D. Rigby

2004-01-01

The purpose of this calculation is to develop estimates of key mechanical properties for the lithophysal rock masses of the Topopah Spring Tuff (Tpt) within the repository host horizon, including their uncertainties and spatial variability. The mechanical properties to be characterized include an elastic parameter, Young's modulus, and a strength parameter, uniaxial compressive strength. Since lithophysal porosity is used as a surrogate property to develop the distributions of the mechanical properties, an estimate of the distribution of lithophysal porosity is also developed. The resulting characterizations of rock parameters are important for supporting the subsurface design, developing the preclosure safety analysis, and assessing the postclosure performance of the repository (e.g., drift degradation and modeling of rockfall impacts on engineered barrier system components)

Process model repositories and PNML

NARCIS (Netherlands)

Hee, van K.M.; Post, R.D.J.; Somers, L.J.A.M.; Werf, van der J.M.E.M.; Kindler, E.

2004-01-01

Bringing system and process models together in repositories facilitates the interchange of model information between modelling tools, and allows the combination and interlinking of complementary models. Petriweb is a web application for managing such repositories. It supports hierarchical process

Radioactive waste repository study

International Nuclear Information System (INIS)

1978-11-01

This is the second part of a report of a preliminary study for AECL. It considers the requirements for an underground waste repository for the disposal of wastes produced by the Canadian Nuclear Fuel Program. The following topics are discussed with reference to the repository: 1) geotechnical assessment, 2) hydrogeology and waste containment, 3) thermal loading and 4) rock mechanics. (author)

Open DOAR the Directory of Open Access Repositories

CERN Multimedia

CERN. Geneva

2005-01-01

The last year has seen wide-spread growth in the idea of using open access repositories as a part of a research institution's accepted infrastructure. Policy development from institutions and funding bodies has also supported the growth of the repository network. The next stage of expansion will be in the provision of services and cross-repository facilities and resources. Of course, it is hoped that these will then establish a feed-back loop to encourage repository population and further repository establishment, as the potential of open access to research materials is realised. The growth of repositories has been organic, with a variety of different repositories based in departments, institutions, funding agencies or subject communities, with a range of content, both in type and subject. Existing repositories are expanding their holdings, from eprints to associated research data-sets, or with learning objects and multimedia material. This presentation will look at the development of the Directory of Open Ac...

Foreign materials in the repository - update of estimated quantities

International Nuclear Information System (INIS)

Hagros, A.

2007-03-01

repository. The materials with the next largest quantities are carbonates and organic materials. If the chosen tunnel backfill alternative is Friedland clay, the material with the largest quantity is gypsum, followed by pyrite, organic materials and cement. The selection of the backfill alternative has a significant impact on the quantities of several important foreign materials and their relative abundance, whereas the differences between the grouting and shotcreting alternatives are minor in terms of total material quantities. (orig.)

Site characterization plan conceptual design report for a high-level nuclear waste repository in salt, vertical emplacement mode: Volume 2

International Nuclear Information System (INIS)

1987-12-01

Chapter 6 discusses the repository design features and operating procedures that will be used to ensure compliance with regulatory limits for preclosure releases, performance objectives for waste retrieval, and performance objectives for postclosure or long-term waste isolation. Chapter 7 discusses the analyses that were conducted in developing the repository design and the impacts of various external factors on the design of repository elements and the repository as a whole. Chapter 8 discusses the engineering design information needs that were identified during conceptual design as necessary to advance the current conceptual design to License Application Design (LAD). The quality assurance (QA) program applicable to the Architect/Engineer (A/E) activities during the repository conceptual design effort is defined in Chapter 9. 146 refs., 44 figs., 21 tabs

Thermal management and analysis for a potential yucca mountain repository

International Nuclear Information System (INIS)

Van Luik, A.

2005-01-01

In the current Yucca Mountain repository design concept, heat from the emplaced. waste (mostly from spent nuclear fuel.) would keep the temperature of the rock around the waste packages higher than the boiling point of water for hundreds to thousands of years after the repository is closed. The design concept allows below-boiling portions of the pillars between drifts to serve as pathways for the drainage of thermally mobilized water and percolating groundwater by limiting the distance that boiling temperatures extend into the surrounding rock. This design concept takes advantage of host rock dry out, which would create a dry environment within the emplacement drifts and reduce the amount of water that might otherwise be available to enter the drifts and contact the waste packages during this thermal pulse. The Yucca Mountain repository design concept also provides flexibility to allow for operation over a range of lower thermal operating conditions. The thermal conditions within the emplacement drifts can be varied, along with the relative humidity, by modifying operational parameters such as the thermal output of the waste packages, the spacing of the waste packages in the emplacement drifts, and. the duration and rate of active and passive ventilation. A lower range has been examined to quantify lower-temperature thermal conditions (temperatures and associated humidity conditions) in the emplacement drifts and to quantify impacts to the required emplacement area and excavated drift length. This information has been used to evaluate the potential long-term performance of a lower-temperature repository and to estimate the increase in costs associated with operating a lower-temperature repository. This presentation provides an overview of the thermal management evaluations that have been conducted to investigate a range of repository thermal conditions and includes a summary of the technical basis that supports these evaluations. The majority of the material

Alternative measure for performance of HLW geologic repository

International Nuclear Information System (INIS)

Joonhang, Ahn; Chambre, P.L.

2001-01-01

A repository performance model that can show effects of canister multiplicity and repository configuration has been developed. Masses of a radionuclide in the repository and in the far field are proposed as performance measures. Canister multiplicity has significant effects on the release of long-lived radionuclides from the repository. As more canisters are included in the same water stream, the radionuclide concentration in the stream increases, but becomes independent of the number of canisters for sufficiently many canisters. Effects of reduction of radionuclide mass in the repository on the repository performance are clearly observed if the canister multiplicity is taken into account and the mass-based measures are applied. (author)

The alternative site selection procedure as covered in the report by the Repository Site Selection Procedures Working Group

International Nuclear Information System (INIS)

Brenner, M.

2005-01-01

The 2002 Act on the Regulated Termination of the Use of Nuclear Power for Industrial Electricity Generation declared Germany's opting out of the peaceful uses of nuclear power. The problem of the permanent management of radioactive residues is becoming more and more important also in the light of that political decision. At the present time, there are no repositories offering the waste management capacities required. Such facilities need to be created. At the present stage, eligible repository sites are the Konrad mine, a former iron ore mine near Salzgitter, and the Gorleben salt dome. While the fate of the Konrad mine as a repository for waste generating negligible amounts of heat continues to be uncertain, despite a plan approval decision of June 2002, the Gorleben repository is still in the planning phase, at present in a dormant state, so to speak. The federal government expressed doubt about the suitability of the Gorleben site. Against this backdrop, the Federal Ministry for the Environment, Nature Conservation, and Nuclear Safety in February 1999 established AkEnd, the Working Group on Repository Site Selection Procedures. The Group was charged with developing, based on sound scientific criteria, a transparent site selection procedure in order to facilitate the search for repository sites. The Working Group presented its final report in December 2002 after approximately four years of work. The Group's proposals about alternative site selection procedures are explained in detail and, above all, reviewed critically. (orig.)

Accelerator Physics Code Web Repository

CERN Document Server

Zimmermann, Frank; Bellodi, G; Benedetto, E; Dorda, U; Giovannozzi, Massimo; Papaphilippou, Y; Pieloni, T; Ruggiero, F; Rumolo, G; Schmidt, F; Todesco, E; Zotter, Bruno W; Payet, J; Bartolini, R; Farvacque, L; Sen, T; Chin, Y H; Ohmi, K; Oide, K; Furman, M; Qiang, J; Sabbi, G L; Seidl, P A; Vay, J L; Friedman, A; Grote, D P; Cousineau, S M; Danilov, V; Holmes, J A; Shishlo, A; Kim, E S; Cai, Y; Pivi, M; Kaltchev, D I; Abell, D T; Katsouleas, Thomas C; Boine-Frankenheim, O; Franchetti, G; Hofmann, I; Machida, S; Wei, J

2006-01-01

In the framework of the CARE HHH European Network, we have developed a web-based dynamic acceleratorphysics code repository. We describe the design, structure and contents of this repository, illustrate its usage, and discuss our future plans, with emphasis on code benchmarking.

ACCELERATION PHYSICS CODE WEB REPOSITORY.

Energy Technology Data Exchange (ETDEWEB)

WEI, J.

2006-06-26

In the framework of the CARE HHH European Network, we have developed a web-based dynamic accelerator-physics code repository. We describe the design, structure and contents of this repository, illustrate its usage, and discuss our future plans, with emphasis on code benchmarking.

Impacts of expanding airport capacity on competition and connectivity: the case of Gatwick and Heathrow

NARCIS (Netherlands)

Burghouwt, G.; Krul, J.; Boonekamp, T.; Lieshout, R.

2014-01-01

The UK Airports Commission has short-listed three options for expanding airport capacity in the UK. One option concerns expansion of Gatwick with an additional runway. The other options concern expansion of runway capacity at Heathrow. The impacts of expansion on passenger and air freight user

Consistency of Network Traffic Repositories: An Overview

NARCIS (Netherlands)

Lastdrager, E.; Lastdrager, E.E.H.; Pras, Aiko

2009-01-01

Traffc repositories with TCP/IP header information are very important for network analysis. Researchers often assume that such repositories reliably represent all traffc that has been flowing over the network; little thoughts are made regarding the consistency of these repositories. Still, for

48 CFR 227.7207 - Contractor data repositories.

Science.gov (United States)

2010-10-01

... repositories. 227.7207 Section 227.7207 Federal Acquisition Regulations System DEFENSE ACQUISITION REGULATIONS... Computer Software and Computer Software Documentation 227.7207 Contractor data repositories. Follow 227.7108 when it is in the Government's interests to have a data repository include computer software or to...

Reference repository design concept for bedded salt

Energy Technology Data Exchange (ETDEWEB)

Carpenter, D.W.; Martin, R.W.

1980-10-08

A reference design concept is presented for the subsurface portions of a nuclear waste repository in bedded salt. General geologic, geotechnical, hydrologic and geochemical data as well as descriptions of the physical systems are provided for use on generic analyses of the pre- and post-sealing performance of repositories in this geologic medium. The geology of bedded salt deposits and the regional and repository horizon stratigraphy are discussed. Structural features of salt beds including discontinuities and dissolution features are presented and their effect on repository performance is discussed. Seismic hazards and the potential effects of earthquakes on underground repositories are presented. The effect on structural stability and worker safety during construction from hydrocarbon and inorganic gases is described. Geohydrologic considerations including regional hydrology, repository scale hydrology and several hydrological failure modes are presented in detail as well as the hydrological considerations that effect repository design. Operational phase performance is discussed with respect to operations, ventilation system, shaft conveyances, waste handling and retrieval systems and receival rates of nuclear waste. Performance analysis of the post sealing period of a nuclear repository is discussed, and parameters to be used in such an analysis are presented along with regulatory constraints. Some judgements are made regarding hydrologic failure scenarios. Finally, the design and licensing process, consistent with the current licensing procedure is described in a format that can be easily understood.

Reference repository design concept for bedded salt

International Nuclear Information System (INIS)

Carpenter, D.W.; Martin, R.W.

1980-01-01

A reference design concept is presented for the subsurface portions of a nuclear waste repository in bedded salt. General geologic, geotechnical, hydrologic and geochemical data as well as descriptions of the physical systems are provided for use on generic analyses of the pre- and post-sealing performance of repositories in this geologic medium. The geology of bedded salt deposits and the regional and repository horizon stratigraphy are discussed. Structural features of salt beds including discontinuities and dissolution features are presented and their effect on repository performance is discussed. Seismic hazards and the potential effects of earthquakes on underground repositories are presented. The effect on structural stability and worker safety during construction from hydrocarbon and inorganic gases is described. Geohydrologic considerations including regional hydrology, repository scale hydrology and several hydrological failure modes are presented in detail as well as the hydrological considerations that effect repository design. Operational phase performance is discussed with respect to operations, ventilation system, shaft conveyances, waste handling and retrieval systems and receival rates of nuclear waste. Performance analysis of the post sealing period of a nuclear repository is discussed, and parameters to be used in such an analysis are presented along with regulatory constraints. Some judgements are made regarding hydrologic failure scenarios. Finally, the design and licensing process, consistent with the current licensing procedure is described in a format that can be easily understood

Implementation plan for the new production reactor capacity environmental impact statement

International Nuclear Information System (INIS)

1989-12-01

The US Department of Energy (DOE) proposed to site, construct, and operate new production reactor (NPR) capacity intended primarily to produce tritium and secondarily to produce plutonium for the US nuclear weapons program. DOE studies show that this new capacity is needed to ensure reliable maintenance of the nation's nuclear weapons stockpile. It also is essential that these necessary nuclear materials be produced in a safe and environmentally sound manner. The DOE has determined that this proposed action constitutes a major federal action that may significantly affect the quality of the human environment; therefore, the DOE will prepare an environmental impact statement (EIS) to assess the potential impacts of the proposed action and reasonable alternatives on the human and natural environment. The EIS will be prepared in accordance with the National Environmental Policy Act of 1969, as implemented in regulations promulgated by the Council on Environmental Quality (CEQ). This EIS implementation plan (IP) includes a description of the proposed action, descriptions of alternatives, a summary of EIS assumptions, a list of environmental issues to be considered in the EIS (including those identified during public scoping activities), a list of proposed agency consultations, a schedule for EIS preparation and related activities, and an annotated outline for the EIS. It is the Department's intent that the EIS on the NPR capacity will serve as the programmatic National Environmental Policy Act (NEPA) review of modernization of DOE defense nuclear materials production of tritium and plutonium. The Department is currently developing a NEPA compliance strategy for modernization of the remainder of the nuclear weapons production complex, which will reference the EIS on NPR capacity. 7 refs., 8 tabs

Draft environmental impact statement siting, construction, and operation of New Production Reactor capacity. Volume 4, Appendices D-R

Energy Technology Data Exchange (ETDEWEB)

None

1991-04-01

This Environmental Impact Statement (EIS) assesses the potential environmental impacts, both on a broad programmatic level and on a project-specific level, concerning a proposed action to provide new tritium production capacity to meet the nation`s nuclear defense requirements well into the 21st century. A capacity equivalent to that of about a 3,000-megawatt (thermal) heavy-water reactor was assumed as a reference basis for analysis in this EIS; this is the approximate capacity of the existing production reactors at DOE`s Savannah River Site near Aiken, South Carolina. The EIS programmatic alternatives address Departmental decisions to be made on whether to build new production facilities, whether to build one or more complexes, what size production capacity to provide, and when to provide this capacity. Project-specific impacts for siting, constructing, and operating new production reactor capacity are assessed for three alternative sites: the Hanford Site near Richland, Washington; the Idaho National Engineering Laboratory near Idaho Falls, Idaho; and the Savannah River Site. For each site, the impacts of three reactor technologies (and supporting facilities) are assessed: a heavy-water reactor, a light-water reactor, and a modular high-temperature gas-cooled reactor. Impacts of the no-action alternative also are assessed. The EIS evaluates impacts related to air quality; noise levels; surface water, groundwater, and wetlands; land use; recreation; visual environment; biotic resources; historical, archaeological, and cultural resources; socioeconomics; transportation; waste management; and human health and safety. The EIS describes in detail the potential radioactive releases from new production reactors and support facilities and assesses the potential doses to workers and the general public. This volume contains 15 appendices.

Web Interface Security Vulnerabilities of European Academic Repositories

Directory of Open Access Journals (Sweden)

Matus Formanek

2017-02-01

Full Text Available The given analysis summarizes the status quo of the level of security of web interfaces of selected European academic repositories in the field of library and information science. It focuses on the presence and qualities of the secure HTTPS protocol via SSL/TLS protocols. The security of the transmitted data is particularly important in the network environment of the Internet, especially if log-in user data is transmitted. Disclosure may have a direct impact on saved digital objects and their metadata which together represent the most valuable parts of systems of digital libraries and repositories. Furthermore, the paper points to the most noticeable vulnerabilities of protocols of web interfaces and presents practical recommendations for the expert public. These may contribute to the increase of the level of security of the discussed systems. The authors base their proposals on the currently available scientific publications and scientific articles about the given topic.

Hydrothermal conditions around a radioactive waste repository

International Nuclear Information System (INIS)

Thunvik, R.; Braester, C.

1981-12-01

Numerical solutions for the hydrothermal conditions around a hard rock repository for nuclear fuel waste are presented. The objective of the present investigation is to illustrate in principle the effect of heat released from a hypothetical radioactive waste repository with regard to anisotropy in the rock permeability. Permeability and porosity are assumed to be constant or to decrease exponentially with depth. The hypothetical repository is situated below a horizontal ground surface or below the crest of a hill, and it is assumed that the water table follows the topography. Major interest in the analysis is directed towards the influence of anisotropy in the permeability on the flow patterns and travel times for water particles, being traced from the repository to the ground surface. The presented results show that anisotropy in the permeability may have a significant influence on the flow conditions around the repository and subsequently also on the travel times from the repository. (Authors)

Strategy for safety case development: impact of a volunteering approach to siting a japanese HLW repository

International Nuclear Information System (INIS)

Kitayama, K.; Ishiguro, K.; Takeuchi, M.; Tsuchi, H.; Kato, T.; Sakabe, Y.; Wakasugi, K.

2008-01-01

NUMO strategy for safety case development is constrained by a staged siting approach, which has been initiated by a call for volunteer municipalities to host the HLW repository. For each site, the safety case is an important factor to be considered at the selection steps which narrow down towards the preferred repository location. This is particularly challenging, however, as every site requires a tailored repository concept, with associated performance assessment and an individual site evaluation programme all of which evolve with gradually increasing understanding of the host environment. In order to maintain flexibility without losing focus, NUMO has developed a formalized tailoring procedure, termed the NUMO Structured Approach (NSA). The NSA guides the interaction of the key site characterisation, repository design and performance assessment groups and is facilitated by tools to help the decision making associated with the tailoring process (e.g. a requirements management system) and with comparison of siting and design options (e.g. multi-attribute analysis). Pragmatically, the post-closure safety case will initially emphasize near-field processes and a robust engineering barrier system, considering the limited geological information at early stages. This will be complemented by a more realistic assessment of total system performance, as needed to compare options. In addition, efforts to rigorously assess operational phase safety and the practicality of assuring quality of the constructed engineered barriers are components of the total safety case which are receiving particular attention now, as they may better discriminate between sites while information is still limited. (authors)

Modeling the impact of climate change in Germany with biosphere models for long-term safety assessment of nuclear waste repositories.

Science.gov (United States)

Staudt, C; Semiochkina, N; Kaiser, J C; Pröhl, G

2013-01-01

Biosphere models are used to evaluate the exposure of populations to radionuclides from a deep geological repository. Since the time frame for assessments of long-time disposal safety is 1 million years, potential future climate changes need to be accounted for. Potential future climate conditions were defined for northern Germany according to model results from the BIOCLIM project. Nine present day reference climate regions were defined to cover those future climate conditions. A biosphere model was developed according to the BIOMASS methodology of the IAEA and model parameters were adjusted to the conditions at the reference climate regions. The model includes exposure pathways common to those reference climate regions in a stylized biosphere and relevant to the exposure of a hypothetical self-sustaining population at the site of potential radionuclide contamination from a deep geological repository. The end points of the model are Biosphere Dose Conversion factors (BDCF) for a range of radionuclides and scenarios normalized for a constant radionuclide concentration in near-surface groundwater. Model results suggest an increased exposure of in dry climate regions with a high impact of drinking water consumption rates and the amount of irrigation water used for agriculture. Copyright © 2012 Elsevier Ltd. All rights reserved.

Generation Capacity Investments and High Levels of Renewables. The Impact of a German Capacity Market on Northwest Europe. Discussion paper

Energy Technology Data Exchange (ETDEWEB)

Ozdemir, O.; De Joode, J.; Koutstaal, P.R.; Van Hout, M. [ECN Policy Studies, Amsterdam (Netherlands)

2013-05-15

Presently, Northwest European centralised electricity markets are designed as 'energy-only' markets. In an energy-only market, the price received for electricity produced is set by the marginal generation unit. Potentially, the designs of these markets could leave the owners of these units with 'missing money': i.e. money that is required to recover investment cost. Further, increasing penetration of renewables could exacerbate this problem. Of all the different options available to tackle the 'missing money' problem, capacity mechanisms have attracted most of the attention in recent policy debates in Europe. This paper contributes to ongoing policy discussions by providing a quantitative analysis of the phenomena of 'missing money' and capacity mechanisms in Northwest Europe. Our analysis shows that in the case of energy-only markets with a much higher penetration of intermittent electricity sources such as wind and solar PV, the 'missing money' problem may be aggravated, because operating hours for peak and mid-merit order capacity will be considerably reduced. Furthermore, unilateral introduction of capacity mechanisms in integrated electricity markets can have considerable impacts on cross-border electricity flows and investment decisions. Stand-alone introduction of a capacity market in Germany will likely result in higher investments in Germany at the expense of lower investments outside Germany and an increase in net exports from Germany. A possible advantage of a unilateral capacity mechanism in Germany may be a reduction in super-peak prices in the larger market area. Thus, neighbouring countries may have the possibility to free ride on the increase in flexible capacity in Germany. However, this advantage is conditional and depends on sufficient availability of interconnection capacity necessary to be able to use this reserve capacity. Otherwise, security of supply might be more at risk if the German

Proposed format and content of environmental reports for deep geologic terminal repositories for radioactive material

International Nuclear Information System (INIS)

Carrell, D.J.; Jones, G.L.

1978-01-01

As the Nuclear Regulatory Commission has not yet issued a format guide for the preparation of an environmental impact statement for radioactive waste repositories, Rockwell Hanford operations has developed an annotated outline which will serve as the basis for the environmental evaluation activities until replaced by an appropriate NRC regulatory guide. According to the outline, the applicant should summarize the major environmental effects that are expected to occur during the construction, operation, and terminal isolation phases of the radioactive material repository. Compare these environmental effects with the possible effect of continued use of interim storage facilities. Unless unforeseen environmental effects become apparent, the summary should be a positive statement indicating that the short-term environmental effects are outweighed by the long-term benefits of the repository

What do we mean by a cold repository?

International Nuclear Information System (INIS)

Halsey, W.G.

1994-01-01

The topic of thermal loading of a potential repository at Yucca Mountain in Nevada has been the subject of intense discussion within the project technical community. While terms such as ''Hot Repository'' and ''Cold Repository'' are frequently used, they have not been clearly defined. In particular, the definition of a cold repository has remained the opinion of each individual. This has led to confusion and misunderstanding. In this paper, a number of observed definitions for a cold repository are discussed along with the technical implications, assumptions and inconsistencies. Finally, a common language is suggested

Deep repository for spent nuclear fuel. Facility description - Layout E. Spiral ramp with one operational area

International Nuclear Information System (INIS)

Pettersson, Stig; Forsgren, Ebbe; Lange, Fritz

2002-04-01

This report documents a proposal for the design of the deep repository for spent nuclear fuel. The proposal is based on the principles that were formulated in the original KBS-3 study, but has been supplemented by investigations and experience to reflect current knowledge. The purpose of the report is to provide an integrated picture of the deep repository, as a basis for SKB's other work, e.g. environmental impact assessments, transport systems, safety issues and alternative locations, and to provide a co-ordinated account of the conditions and requirements concerning all of the necessary functions in the deep repository in order to have a well functioning facility. In addition, it should be possible to use the report as: a tool in the task of achieving a co-ordinated, safe and accepted design for the facility, a basis for further planning and costing, a basis for adaptation to geographic and other conditions for the particular location, a basis for information material, both within SKB and for interested parties outside, such as public authorities, municipalities and the general public. The capacity of the deep repository has been chosen on the basis of 40 years of operation of the Swedish nuclear power reactors, which will produce approximately 9,000 tons of uranium, equivalent to approximately 4,500 canisters. The design outlined is based on theoretical analyses of functions, safety requirements, procedures etc. that can be identified during the various phases of the construction and operation of the repository. In addition, preliminary organisation and staffing plans have been drawn up, for use as the basis for planning the necessary buildings. The report gives a vision of the overall layout and function of the facility, and a proposal for the design of all individual parts of the repository. The relationships between the various parts of the repository are described, both above and below ground, as is the interplay between the part above ground and part below

Deep repository for spent nuclear fuel. Facility description - Layout E. Spiral ramp with one operational area

Energy Technology Data Exchange (ETDEWEB)

Pettersson, Stig [Swedish Nuclear Fuel and Waste Management Co., Stockholm (Sweden); Forsgren, Ebbe [SwedPower AB, Stockholm (Sweden); Lange, Fritz [Lange Art AB, Stockholm (Sweden)

2002-04-01

This report documents a proposal for the design of the deep repository for spent nuclear fuel. The proposal is based on the principles that were formulated in the original KBS-3 study, but has been supplemented by investigations and experience to reflect current knowledge. The purpose of the report is to provide an integrated picture of the deep repository, as a basis for SKB's other work, e.g. environmental impact assessments, transport systems, safety issues and alternative locations, and to provide a co-ordinated account of the conditions and requirements concerning all of the necessary functions in the deep repository in order to have a well functioning facility. In addition, it should be possible to use the report as: a tool in the task of achieving a co-ordinated, safe and accepted design for the facility, a basis for further planning and costing, a basis for adaptation to geographic and other conditions for the particular location, a basis for information material, both within SKB and for interested parties outside, such as public authorities, municipalities and the general public. The capacity of the deep repository has been chosen on the basis of 40 years of operation of the Swedish nuclear power reactors, which will produce approximately 9,000 tons of uranium, equivalent to approximately 4,500 canisters. The design outlined is based on theoretical analyses of functions, safety requirements, procedures etc. that can be identified during the various phases of the construction and operation of the repository. In addition, preliminary organisation and staffing plans have been drawn up, for use as the basis for planning the necessary buildings. The report gives a vision of the overall layout and function of the facility, and a proposal for the design of all individual parts of the repository. The relationships between the various parts of the repository are described, both above and below ground, as is the interplay between the part above ground and part

Compliance demonstration: What can be reasonably expected from safety assessment for geological repositories?

International Nuclear Information System (INIS)

Zuidema, P.; Smith, P.; Sumerling, T.

1999-01-01

When licensing a nuclear facility, it is important to demonstrate that it will comply with regulatory limits (e.g. individual dose limits) and also show that sufficient attention has been paid to optimisation of facility design and operation, such that any associated radiological impacts will be as low as reasonably achievable (ALARA). In general, in demonstrating compliance, experience can be drawn from the performance of existing and similar facilities, and monitoring plans can be specified that will confirm that actual radiological discharges during operations are within authorised limits for the facility. This is also true in respect of the operational period of a geological repository. For the post-closure phase of a repository, however, it is also necessary to show that possible releases will remain acceptably low even at long times in the future when, it is assumed, control of the facility has lapsed and there is no method of either monitoring releases or taking remedial action in the case of unexpected events or releases. In addition, within each country, a deep geological repository will be a first-of-a-kind development so that compliance arguments can be expected to be rigorously tested without any assistance from the precedent of licensing of similar facilities nationally. This puts heavy, and quite unusual, burdens on the long-term safety assessment for a geological repository to develop a case that is sufficiently strong to demonstrate compliance. This paper focuses on the problem of demonstrating compliance with long-term safety requirements for a geological repository, and explores: the overall aims and special difficulties of demonstrating compliance for a geological repository; the role of safety assessment in demonstrating compliance; the scope for optimisation of a geological repository and importance of robustness and lessons learnt from the application of safety assessment. In addition, some issues requiring further discussion and clarification

Report on draft Area Recommendation Report for the Crystalline Repository Project

International Nuclear Information System (INIS)

1987-01-01

The draft Area Recommendation Report for the Crystalline Repository Project (ARR) is one product which is part and parcel of a process which was established by Congress and implemented by the Department of Energy. Congress, by enacting the Nuclear Waste Policy Act of 1982 (NWPA), Published Law 97-425, 96 stat 2201, 42 USC 10101, directed the Department of Energy to establish a national program which would provide for the development of repositories for the disposal of high-level radioactive waste and spent nuclear fuel, The NWPA requires, among other things, that affected Tribes and States be provided the opportunity to participate fully in the development of proposed repositories. The Fond du Lac Tribe is an affected tribe whose proprietary interests will be impacted by the Crystalline Repository Project as identified in the draft ARR. The draft ARR does not meet the obligations of the NWPA, the Treaties of 1837 and 1842 or the Trust Responsibility to Indian Tribes. The NWPA required participation by affected tribes, of which the Fond du Lac Band of Lake Superior Chippewa is included. This exclusion has placed in question the validity of the initial CRP process and does not adequately protect the interest of the Fond du Lac Band. Further study is required to fully appreciate the total affect that the Fond du Lac Bands interest may have on this report

Report on Modeling Coupled Processes in the Near Field of a Clay Repository

Energy Technology Data Exchange (ETDEWEB)

Liu, Hui -Hai [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Houseworth, Jim [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Rutqvist, Jonny [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Li, Lianchong [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Asahina, Daisuke [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Chen, Fei [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Birkholzer, Jens [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States)

2012-08-01

Clay/shale has been considered as potential host rock for geological disposal of high-level radioactive waste throughout the world. Coupled thermal, hydrological, mechanical, and chemical (THMC) processes have a significant impact on the long-term safety of a clay repository. For example, the excavation damaged zone (EDZ) near repository tunnels can modify local permeability (resulting from induced fractures), potentially leading to less confinement capability. This report documents results from three R&D activities: (1) implementation and validation of constitutive relationships, (2) development of a discrete fracture network (DFN) model for investigating coupled processes in the EDZ, and (3) development of a THM model for the FE tests at Mont Terri, Switzerland, for the purpose of model validation. The overall objective of these activities is to provide an improved understanding of EDZ evolution in clay repositories and the associated coupled processes, and to develop advanced relevant modeling capabilities.

Project Mapping to Build Capacity and Demonstrate Impact in the Earth Sciences

Science.gov (United States)

Hemmings, S. N.; Searby, N. D.; Murphy, K. J.; Mataya, C. J.; Crepps, G.; Clayton, A.; Stevens, C. L.

2017-12-01

Diverse organizations are increasingly using project mapping to communicate location-based information about their activities. NASA's Earth Science Division (ESD), through the Earth Science Data Systems and Applied Sciences' Capacity Building Program (CBP), has created a geographic information system of all ESD projects to support internal program management for the agency. The CBP's NASA DEVELOP program has built an interactive mapping tool to support capacity building for the program's varied constituents. This presentation will explore the types of programmatic opportunities provided by a geographic approach to management, communication, and strategic planning. We will also discuss the various external benefits that mapping supports and that build capacity in the Earth sciences. These include activities such as project matching (location-focused synergies), portfolio planning, inter- and intra-organizational collaboration, science diplomacy, and basic impact analysis.

Radioactive waste repository study

International Nuclear Information System (INIS)

1978-11-01

This is the first part of a report of a preliminary study for Atomic Energy of Canada Limited. It considers the requirements for an underground waste repository for the disposal of wastes produced by the Canadian Nuclear Fuel Program. The following topics are discussed with reference to the repository: 1) underground layout, 2) cost estimates, 3) waste handling, 4) retrievability, decommissioning, sealing and monitoring, and 5) research and design engineering requirements. (author)

MAJOR REPOSITORY DESIGN ISSUES

International Nuclear Information System (INIS)

JACK N. BAILEY, DWAYNE CHESTNUT, JAMES COMPTON AND RICHARD D. SNELL

1997-01-01

The Yucca Mountain Project is focused on producing a four-part viability assessment in late FY98. Its four components (design, performance assessment, cost estimate, and licensing development plan) must be consistent. As a tool to compare design and performance assessment options, a series of repository pictures were developed for the sequential time phases of a repository. The boundaries of the time phases correspond to evolution in the engineered barrier system (EBS)

An analysis of repository waste-handling operations

International Nuclear Information System (INIS)

Dennis, A.W.

1990-09-01

This report has been prepared to document the operational analysis of waste-handling facilities at a geologic repository for high-level nuclear waste. The site currently under investigation for the geologic repository is located at Yucca Mountain, Nye County, Nevada. The repository waste-handling operations have been identified and analyzed for the year 2011, a steady-state year during which the repository receives spent nuclear fuel containing the equivalent of 3000 metric tons of uranium (MTU) and defense high-level waste containing the equivalent of 400 MTU. As a result of this analysis, it has been determined that the waste-handling facilities are adequate to receive, prepare, store, and emplace the projected quantity of waste on an annual basis. In addition, several areas have been identified where additional work is required. The recommendations for future work have been divided into three categories: items that affect the total waste management system, operations within the repository boundary, and the methodology used to perform operational analyses for repository designs. 7 refs., 48 figs., 11 tabs

Memory provisions for the Manche Surface Repository

International Nuclear Information System (INIS)

Dumont, Jean-Noel; Espiet-Subert, Florence

2015-01-01

The French La Manche repository site received its last radioactive waste package in 1994. In 2003, the official surveillance phase of the closed repository started under the supervision of Andra (the national industrial operator), the French Nuclear Safety Authority (ASN) and society (e.g. the local municipalities). Florence Espiet explained that information on the existence of the repository, its content, how it was operated and how it works needs to be preserved. It also is planned to review the information periodically for a minimum of 300 years. She described the creation of two documents on memory (a detailed and a summary one), both on permanent paper, and the preservation of the land registration. The latter constitutes 'passive' provisions for preserving memory. In addition, a number of 'active' provisions are and will be put in place: guided visits, exhibitions, partnerships with organisations dealing with memory preservation, and the creation of a think tank. The latter consists of local citizens and politicians, retired employees from Andra and artists that meet several times a year and reflect on memory preservation from the perspective of, for instance, local history, education, arts and rituals. Finally, two types of markers will be used to preserve the repository's memory: i) three herbaria cataloguing the plants growing on the site of the repository, including a very short description of the repository, will be stored at different sites in France; ii) a stele indicating the main characteristics of the repository, potentially linked to an art work, will be erected at the repository

Studies relating to human intrusion into a repository. Report pertaining to work package 11. Preliminary safety case of the Gorleben site (VSG)

Energy Technology Data Exchange (ETDEWEB)

Beuth, Thomas; Buhmann, Dieter; Fischer-Appelt, Klaus; Moenig, Joerg; Ruebel, Andre; Wolf, Jens [Gesellschaft fuer Anlagen- und Reaktorsicherheit mbH (GRS), Koeln (Germany); Bollingerfehr, Wilhelm; Filbert, Wolfgang [DBE Technology GmbH, Peine (Germany); Charlier, Frank [international nuclear safety engineering gmbh (nse), Aachen (Germany); Baltes, Bruno

2014-10-15

The question of the long-term safety of a repository system is inseparably linked with the intensive technical examination of the possible future evolution of the site and the repository system e. g. as a result of climatic, geologic, waste-related and repository-related processes. Here, the possible evolutions to be considered are those that have the potential to have a negative impact on the intended, furthest-possible, immediate, and lasting isolation of the radioactive waste in a defined area around the underground workings of the repository mine in salt rock, which is referred to as the containment-providing rock zone (CPRZ).

General conceptual design study for a high level radioactive waste repository in a granite formation. Volume 1

International Nuclear Information System (INIS)

1982-01-01

The object of the general conceptual design study for a repository for disposal of radioactive waste in a granite formation is to ensure that the technology available in 1980 is suitable for the construction of such a repository. The recommended techniques and equipment are suitable for construction of a repository, located at a depth of 1000 metres in a granite batholith, with a capacity of 30,000 AVM canisters, cooled for 30 years on the surface, at a rate of 1,000 canisters per year. The structure consists of six access shafts of 4 and 5 metres diameter, drilled from the surface by the big-hole method, serving a network of 82 parallel galleries, 2,300 metres long, mined by conventional blasting. Shafts 100 metres deep are drilled in the floor of each gallery (74 shafts per gallery), each shaft accommodating five canisters. This represents an aggregate gallery length of 200 kilometres and an aggregate shaft length of 600 kilometres. The cost of the operation is 1.3% of the cost (ex-works) of the energy produced by the power stations generating the waste. Construction, operation and final abandonment will take 81 years. The sensitivity study of the design showed, by varying certain parameters, that location of the repository at a depth of 500 metres is not recommended and that the area covered by the repository of 4 km 2 is halved if the canisters are first cooled for 100 years

Scientific basis for a safety case of deep geological repositories

Energy Technology Data Exchange (ETDEWEB)

Noseck, Ulrich; Becker, Dirk-Alexander; Brasser, Thomas [and others

2012-11-15

: - The current state-of-the-art in long-term safety assessment has been evaluated within a sub project of the Integration Group for the safety case (IGSC) of OECD/NEA. GRS has strongly contributed to this project called Methods for Safety Assessments (MeSA), by leading working groups and with contributions to selected chapters of the NEA state-of-the-art report. - As an outcome of the MeSA project it was decided to compile the status in the OECD member countries on the use of indicators complementary to dose and risk in the safety case. GRS played a leading role in drafting and finalizing a state-of-the-art report on indicators. Further the applicability of a specific set of indicators previously proposed in Germany was tested and evaluated for repositories in clay and rock salt formations. - GRS is involved in several international working groups to follow the state-of-the-art at the international level as well as to introduce results from German R and D into the international discussion. Important working groups are the Radioactive Waste Management Committee (RWMC) of OECD/NEA with the Integration Group for the Safety Case, its subgroups Clay Club and Salt Club and correlated projects like the NEA sorption project. - The current literature dealing with the role of microbial processes related to repositories in clay formations has been compiled. The potential negative and positive impact of microbes on the long-term integrity of the repository system in clay has been qualitatively evaluated. - Radionuclide inventories of CSD-V containers received from reprocessing in LA Hague have been evaluated and an updated data set for long-term safety assessment is proposed. - The non-isothermal re-saturation of bentonite is investigated by specific laboratory experiments accompanied by modelling with the code VIPER. In addition the model was applied to lab and field experiments provided by the EBS task force and all results have been discussed in this international working group

Scientific basis for a safety case of deep geological repositories

International Nuclear Information System (INIS)

Noseck, Ulrich; Becker, Dirk-Alexander; Brasser, Thomas

2012-11-01

: - The current state-of-the-art in long-term safety assessment has been evaluated within a sub project of the Integration Group for the safety case (IGSC) of OECD/NEA. GRS has strongly contributed to this project called Methods for Safety Assessments (MeSA), by leading working groups and with contributions to selected chapters of the NEA state-of-the-art report. - As an outcome of the MeSA project it was decided to compile the status in the OECD member countries on the use of indicators complementary to dose and risk in the safety case. GRS played a leading role in drafting and finalizing a state-of-the-art report on indicators. Further the applicability of a specific set of indicators previously proposed in Germany was tested and evaluated for repositories in clay and rock salt formations. - GRS is involved in several international working groups to follow the state-of-the-art at the international level as well as to introduce results from German R and D into the international discussion. Important working groups are the Radioactive Waste Management Committee (RWMC) of OECD/NEA with the Integration Group for the Safety Case, its subgroups Clay Club and Salt Club and correlated projects like the NEA sorption project. - The current literature dealing with the role of microbial processes related to repositories in clay formations has been compiled. The potential negative and positive impact of microbes on the long-term integrity of the repository system in clay has been qualitatively evaluated. - Radionuclide inventories of CSD-V containers received from reprocessing in LA Hague have been evaluated and an updated data set for long-term safety assessment is proposed. - The non-isothermal re-saturation of bentonite is investigated by specific laboratory experiments accompanied by modelling with the code VIPER. In addition the model was applied to lab and field experiments provided by the EBS task force and all results have been discussed in this international working group

Monitoring during the stepwise implementation of the Swedish deep repository for spent fuel

Energy Technology Data Exchange (ETDEWEB)

Baeckblom, Goeran [Conrox (Sweden); Almen, Karl-Erik [KEA Geokonsult AB (Sweden)

2004-03-01

monitoring are to: obtain knowledge of undisturbed conditions in nature and their seasonal variations (baseline) in order to identify and evaluate the impact of activities related to the deep repository during different phases, obtain a better understanding of the function of the deep repository system to support the safety account and to test models and assumptions, monitor the environmental impact of the deep repository, provide evidence that the working environment is safe with regard to radiological and non-radiological effects, show that requirements on radioactive waste verification (safeguards) are fulfilled. The monitoring is concerned with bedrock conditions before and during construction and operation of the facilities, active design to engineer the underground facilities based on monitoring results during construction, the safe and environmental construction and operation of facilities. Experience exists from monitoring of the barrier function at SFR, the final repository for low - and intermediate level waste and at the Aespoe Hard Rock Laboratory and monitoring for safeguard at CLAB, the interim storage for spent nuclear fuel. The know-how on monitoring relates to all aspects from design, installation, operation and maintenance to decommissioning of systems. This report provides an overview of the features, processes and parameters that are collected during the site investigations to establish the Primary Baseline conditions for monitoring prior to the construction of the repository. It is also proposed that the monitoring programme should at least entail the following elements: objectives for the monitoring programme, scope for the monitoring (criteria for selection of issues to be monitored, identification of the properties, processes, phenomena and observable quantities to be monitored), identification on what methods to be used, operation of the monitoring system (identification of the duration and frequency of monitoring, including criteria for when

Natural analogue studies in crystalline rock: the influence of water-bearing fractures on radionuclide immobilisation in a granitic rock repository

International Nuclear Information System (INIS)

Alexander, W.R.; MacKenzie, A.B.; Scott, R.D.; McKinley, I.G.

1990-06-01

Current Swiss concepts for the disposal of radioactive waste involve disposal in deep mined repositories to ensure that only insignificant quantities of radionuclides will ever reach the surface and so enter the biosphere. The rock formations presently considered as potential candidates for hosting radwaste repositories have thus been selected on the basis of their capacity to isolate radionuclides from the biosphere. An important factor in ensuring such containment is a very low solute transport rate through the host formation. However, it is considered likely that, in the formations of interest in the Swiss programme (eg. granites, argillaceous sediments, anhydrite), the rocks will be fractured to some extent even at repository depth. In the instance of the cumulative failure of near-field barriers in the repository, these hydraulically connected fractures in the host formation could be very important far-field routes of migration (and possible sites of retardation) of radionuclides dissolved in the groundwaters. In this context, the so-called 'matrix diffusion' mechanism is potentially very important for radionuclide retardation. This report is the culmination of a programme which has attempted to assess the potential influence of these water-bearing fractures on radionuclide transport in a crystalline rock radwaste repository. 162 refs., 36 figs., 16 tabs

Safety analysis in subsurface repositories

International Nuclear Information System (INIS)

1985-06-01

The development of mathematical models to represent the repository-geosphere-biosphere system, and the development of a structure for data acquisition, processing, and use to analyse the safety of subsurface repositories, are presented. To study the behavior of radionuclides in geosphere a laboratory to determine the hydrodynamic dispersion coefficient was constructed. (M.C.K.) [pt

How many geologic repositories will be needed

International Nuclear Information System (INIS)

Evans, T.J.; Halstead, R.J.

1987-01-01

DOE's postponement of site-specific work on the second repository program had rekindled debate over the number of geologic repositories needed for disposal of high level radioactive waste. The multiple repository approach grew out of the March, 1979 IRG report, which recommended co-disposal of civilian and defense HLW in a system of regional repositories. The multiple repository approach was adopted by DOE, and incorporated in the Nuclear Waste Policy Act passed by Congress in December, 1982. Since the late 1970's, the slower than anticipated growth of the nuclear power industry has substantially reduced earlier estimates of the amount of civilian spent fuel which will require geologic disposal. Reactors currently in operation (78.5 GWe) and reactors in the construction pipeline (28 GWe) are expected to discharge about 103,200 MTU of spent fuel by the year 2036, assuming no increase in fuel burnup rate. By the year 2020, defense high level radioactive wastes equivalent to as much as 27,000 MTU could require geologic disposal. Small amounts of high level waste from other sources will also require geologic disposal. Total disposal requirements appear to be less than 140,000 MTU. The five sites nominated for the first repository, as well as hypothetical sites in granite, the host rock under primary consideration for the second repository, all appear capable of accommodating up to 140,000 MTU

Influence of Iltization on the Ion-sorbing Capacity of Smectitic Clay

International Nuclear Information System (INIS)

Lee, Jae Owan; Cho, Won Jin

2008-01-01

A high-level waste(HLW) repository uses smectitic clay as a buffer material to inhibit the penetration of groundwater and to retard the release of radionuclides from the radioactive wastes to the surrounding environment. However, when the smectitic clay is exposed to an elevated temperature due to radioactive decay heat and geochemical conditions for a long time, its physicochemical and mineralogical properties may be degradated and thus lose its barrier functions. It has been known in literature that the degradation of these properties of the smectitic clay occurs by a illitization in which the smectite transforms into illite. Therefore, an understanding of the illitization is essential to evaluate the long-term barrier performance of smectitic clay for the buffer of a HLW repository. This paper will carry out hydrothermal reaction tests with domestic smectitic clay which will be favorably considered for the buffer material of a Korean HLW repository, and also investigate the influence of illization on the ion-sorbing capacity of the smectitic clay

Integrity of radioactive waste packages at the Yucca mountain repository

International Nuclear Information System (INIS)

Sandquist, G.; Biaglow, A.; Huber, M.; Jagmin, C.

2004-01-01

Several of the important physical and chemical processes that impact the integrity of the radioactive waste packages planned for disposal at the proposed Repository at Yucca Mountain are examined. These processes are described by the aerodynamic, thermodynamic, and chemical interactions associated with the waste packages. The effects of chemical corrosion, mechanical erosion, temperature distributions throughout the repository environs, interactions of air, water, and solid particles, and radiological and biological influences are addressed. Materials will be exposed to at least 3 conditions threatening the integrity of the waste package: 1) accumulated dust and particles on the package surface and suspended in the air, 2) chemical reactions from deposits on the waste package infrastructure materials and tight contact areas, and crevices, and 3) environmental factors affecting chemical reactions such as moisture, pH, Eh, and radiolysis. All 3 of these conditions can combine and produce damaging impacts upon the thin protective layer on the alloy surface of the waste package. There are certain benefits from the low-temperature operating mode with ambient temperature below 85 Celsius degrees, but the materials could be subjected to a maximum temperature of 180 Celsius degrees which might introduce stress corrosion cracking and high temperature effects

Waste Package and Material Testing for the Proposed Yucca Mountain High Level Waste Repository

International Nuclear Information System (INIS)

Doering, Thomas; Pasupathi, V.

2002-01-01

Over the repository lifetime, the waste package containment barriers will perform various functions that will change with time. During the operational period, the barriers will function as vessels for handling, emplacement, and waste retrieval (if necessary). During the years following repository closure, the containment barriers will be relied upon to provide substantially complete containment, through 10,000 years and beyond. Following the substantially complete containment phase, the barriers and the waste package internal structures help minimize release of radionuclides by aqueous- and gaseous-phase transport. These requirements have lead to a defense-in-depth design philosophy. A multi-barrier design will result in a lower breach rate distributed over a longer period of time, thereby ensuring the regulatory requirements are met. The design of the Engineered Barrier System (EBS) has evolved. The initial waste package design was a thin walled package, 3/8 inch of stainless steel 304, that had very limited capacity, (3 PWR and 4 BWR assemblies) and performance characteristics, 300 to 1,000 years. This design required over 35,000 waste packages compared to today's design of just over 10,000 waste packages. The waste package designs are now based on a defense-in-depth/multi-barrier philosophy and have a capacity similar to the standard storage and rail transported spent nuclear fuel casks. Concurrent with the development of the design of the waste packages, a comprehensive waste package materials testing program has been undertaken to support the selection of containment barrier materials and to develop predictive models for the long-term behavior of these materials under expected repository conditions. The testing program includes both long-term and short-term tests and the results from these tests combination with the data published in the open literature are being used to develop models for predicting performance of the waste packages

1972 preliminary safety analysis report based on a conceptual design of a proposed repository in Kansas

International Nuclear Information System (INIS)

Blomeke, J.O.

1977-08-01

This preliminary safety analysis report is based on a proposed Federal Repository at Lyons, Kansas, for receiving, handling, and depositing radioactive solid wastes in bedded salt during the remainder of this century. The safety analysis applies to a hypothetical site in central Kansas identical to the Lyons site, except that it is free of nearby salt solution-mining operations and bore holes that cannot be plugged to Repository specifications. This PSAR contains much information that also appears in the conceptual design report. Much of the geological-hydrological information was gathered in the Lyons area. This report is organized in 16 sections: considerations leading to the proposed Repository, design requirements and criteria, a description of the Lyons site and its environs, land improvements, support facilities, utilities, different impacts of Repository operations, safety analysis, design confirmation program, operational management, requirements for eventually decommissioning the facility, design criteria for protection from severe natural events, and the proposed program of experimental investigations

1972 preliminary safety analysis report based on a conceptual design of a proposed repository in Kansas

Energy Technology Data Exchange (ETDEWEB)

Blomeke, J.O.

1977-08-01

This preliminary safety analysis report is based on a proposed Federal Repository at Lyons, Kansas, for receiving, handling, and depositing radioactive solid wastes in bedded salt during the remainder of this century. The safety analysis applies to a hypothetical site in central Kansas identical to the Lyons site, except that it is free of nearby salt solution-mining operations and bore holes that cannot be plugged to Repository specifications. This PSAR contains much information that also appears in the conceptual design report. Much of the geological-hydrological information was gathered in the Lyons area. This report is organized in 16 sections: considerations leading to the proposed Repository, design requirements and criteria, a description of the Lyons site and its environs, land improvements, support facilities, utilities, different impacts of Repository operations, safety analysis, design confirmation program, operational management, requirements for eventually decommissioning the facility, design criteria for protection from severe natural events, and the proposed program of experimental investigations. (DLC)

Dispute resolution in the nuclear waste repository program

International Nuclear Information System (INIS)

Creighton, J.L.; Shorett, A.J.

1988-01-01

During 1987 a seven-person team addressed just that question for the State of Washington, as part of the studies of the socioeconomic impacts of a possible nuclear waste repository site at the Hanford site. The authors were, respectively, the Mitigation/Compensation team leader and the conflict resolution specialist within the team. While the studies were terminated when Congress selected the Nevada site, the conclusions may still have value for the State of Nevada, or for other controversial federal projects

Report on the evaluation under the Act No 24/2006 of Coll. Environmental Impact Assessment Law Extension of National Radioactive Waste Repository in Mochovce for disposal low-level radioactive waste and construction of very low-level radioactive waste repository; Sprava o hodnoteni v zmysle zakona NR SR c.24/2006 o posudzovani vplyvov na ZP. Rozsirenie RU RAO v Mochovciach pre ukladanie NSAO a vybudovanie uloziska pre VNAO

Energy Technology Data Exchange (ETDEWEB)

Hanusik, V; Moravek, J; Kusovska, Z [VUJE, a.s., 91864 Trnava (Slovakia)

2011-11-30

The report elaborated assessment of the environmental impact of extension of the National Radioactive Waste Repository in Mochovce for disposal of low and intermediate level radioactive wastes. Within this repository also the premises for very low level radioactive waste deposition should be built. The assessment report was prepared according to the Act no. 24/2006 Coll, as amended 'On the assessment of environmental impacts' Annex No. 11 upon The scope of assessment issued by the competent authority on the basis of assessment of Intent for this action. The report was prepared in VUJE, Inc. Trnava for Nuclear and Decommissioning Company, Inc. Bratislava (JAVYS).

Thermo-Hydro Mechanical Characteristics and Processes in the Clay Barrier of a High Level Radioactive Waste Repository. State of the Art Report

International Nuclear Information System (INIS)

Villar, M. V.

2004-01-01

This document is a summary of the available information on the thermo-hydro-mechanical properties of the bentonite barrier of a high-level radioactive waste repository and of the processes taking place in it during the successive repository operation phases. Mainly the thermal properties, the volume change processes (swelling and consolidation), the permeability and the water retention capacity are analysed. A review is made of the existing experimental knowledge on the modification of the these properties by the effect of temperature, water salinity, humidity and density of the bentonite, and their foreseen evolution as a consequence of the processes expected in the repository. The compiled evolution refers mostly to the FEBEX (Spain), the MX-80 (USA) and the FoCa (France) bentonite, considered as reference barrier materials in several European disposal concepts. (Author) 102 refs

Thermo-Hydro Mechanical Characteristics and Processes in the Clay Barrier of a High Level Radioactive Waste Repository. State of the Art Report

Energy Technology Data Exchange (ETDEWEB)

Villar, M. V.

2004-07-01

This document is a summary of the available information on the thermo-hydro-mechanical properties of the bentonite barrier of a high-level radioactive waste repository and of the processes taking place in it during the successive repository operation phases. Mainly the thermal properties, the volume change processes (swelling and consolidation), the permeability and the water retention capacity are analysed. A review is made of the existing experimental knowledge on the modification of the these properties by the effect of temperature, water salinity, humidity and density of the bentonite, and their foreseen evolution as a consequence of the processes expected in the repository. The compiled evolution refers mostly to the FEBEX (Spain), the MX-80 (US) and the FoCa (France) bentonite, considered as reference barrier materials in several European disposal concepts. (Author) 102 refs.

Safety Report within the licence application for the siting of a radioactive waste repository/disposal facility

International Nuclear Information System (INIS)

Horyna, J.; Sinaglova, R.

2004-01-01

The initial safety specification report, which is submitted to the licensing authority as one of the application documents, is the basic document assessing the planned repository/disposal facility with respect to the suitability of the chosen site for this purpose. The following topics are covered: General information; Description and evidence of suitability of the site chosen; Description and tentative assessment of the repository/disposal facility design; Tentative assessment of impacts of running the facility on the employees, general public and environment (radionuclide inventory, transport routes, radionuclide release in normal, abnormal and emergency situations); Proposed concept of repository/disposal facility shutdown; and Assessment of quality assurance in the site selection, in preparatory work for the construction of the facility and in the subsequent stages. (P.A.)

Radio ecological background for the isolation approach for the safety assessment of repositories

International Nuclear Information System (INIS)

Baltes, Bruno; Becker, Angela; Kindt, Anke

2007-01-01

A repository for radioactive waste should only be licensed if it poses no hazard to man and the environment. State of the art is the calculation of the potential radiation exposure of individuals in the surrounding area. A new concept has now been developed to assess the safe closure of radioactive waste in the isolating rock zone. Six criteria allow the quantification of the impact of the repository on the natural environmental conditions starting from the isolating rock zone over pore water and accessible water to the concentration in flora and fauna and to radiation exposure of humans placing the hitherto only criterion into a wider context. (orig.)

Recommendations: Procedure to develop a preliminary safety report as part of the radioactive waste repository construction licensing process

International Nuclear Information System (INIS)

2003-01-01

The structure of a preliminary safety report for the title purpose should be as follows: A. Textual part: 1. General (Introduction, Basic information about the construction, Timetable); 2. Site information (Siting, Geography and demography, Meteorology and climatic situation, Hydrology, Geology and hydrogeology); 3. Repository design description (Basic function and performance requirements, Design, Auxiliary systems, Fire prevention/protection, Emergency plans); 4. Operation of the repository (Waste acceptance and inspection, Waste handling and interim storage, Waste disposal, Operating monitoring), 5. Health and environmental impact assessment (Radionuclide inventory, Radionuclide transport paths and mechanisms of release into the environment, Radionuclide release in normal and emergency situations, Radiation protection - health impact assessment and regulatory compliance, Draft operating limits and conditions, Proposed ways of assuring physical protection, Uncertainty assessment), 6. Safe repository shutdown/decommissioning concept, 7 Quality assurance assessment, 8. List of selected equipment. B. Annexes: Maps, Drawings, Diagrams, Miscellaneous; C. Documentation: Previous safety report amendments, Protocols, Miscellaneous. (P.A.)

Empowerment impact assessment (EmpIA), a tool for poverty alleviation and capacity building

CSIR Research Space (South Africa)

Louw, MR

2006-09-01

Full Text Available their quality of life. xrhombus Facilitate the upgrading of the social and physical environment. xrhombus Increase employment. xrhombus Reduce poverty. xrhombus Stimulate economic growth. xrhombus Reduce imbalances in access to economic opportunities. 1... IMPACT ASSESSMENT (EmpIA), A TOOL FOR POVERTY ALLEVIATION AND CAPACITY BUILDING M.R. LOUW CSIR Built Environment: Pretoria, P.O. Box 395, Pretoria, 0001 ABSTRACT Empowerment impact assessment (EmpIA) is a quantitative...

Building Scientific Data's list of recommended data repositories

Science.gov (United States)

Hufton, A. L.; Khodiyar, V.; Hrynaszkiewicz, I.

2016-12-01

When Scientific Data launched in 2014 we provided our authors with a list of recommended data repositories to help them identify data hosting options that were likely to meet the journal's requirements. This list has grown in size and scope, and is now a central resource for authors across the Nature-titled journals. It has also been used in the development of data deposition policies and recommended repository lists across Springer Nature and at other publishers. Each new addition to the list is assessed according to a series of criteria that emphasize the stability of the resource, its commitment to principles of open science and its implementation of relevant community standards and reporting guidelines. A preference is expressed for repositories that issue digital object identifiers (DOIs) through the DataCite system and that share data under the Creative Commons CC0 waiver. Scientific Data currently lists fourteen repositories that focus on specific areas within the Earth and environmental sciences, as well as the broad scope repositories, Dryad and figshare. Readers can browse and filter datasets published at the journal by the host repository using ISA-explorer, a demo tool built by the ISA-tools team at Oxford University1. We believe that well-maintained lists like this one help publishers build a network of trust with community data repositories and provide an important complement to more comprehensive data repository indices and more formal certification efforts. In parallel, Scientific Data has also improved its policies to better support submissions from authors using institutional and project-specific repositories, without requiring each to apply for listing individually. Online resources Journal homepage: http://www.nature.com/scientificdata Data repository criteria: http://www.nature.com/sdata/policies/data-policies#repo-criteria Recommended data repositories: http://www.nature.com/sdata/policies/repositories Archived copies of the list: https

The SocioEconomic analysis of repository siting (SEARS): Guide to data base preparation: Final draft

International Nuclear Information System (INIS)

Hamm, R.R.; Murdock, S.H.; Leistritz, F.L.; Kiel, B.; Parpia, B.

1984-11-01

This guide describes the data bases in the SocioEconomic Analysis of Repository Siting (SEARS) modeling system. This model is a user-interactive, computerized model for projecting the economic, demographic, public service, and fiscal impacts of repository siting. This guide provides a description of the data bases, sources of data, data formats, and preprocessing programs for adapting and implementing the SEARS system and is seen as an essential reference for technical users of the model. It should be used in conjunction with reports describing the model's features and characteristics. 95 refs., 3 tabs

Area recommendation report for the crystalline repository project: An evaluation

International Nuclear Information System (INIS)

Beck, J.E.; Lowe, H.; Yurkovich, S.P.

1986-01-01

An evaluation is given of DOE's recommendation of the Elk River complex in North Carolina for siting the second repository. Twelve recommendations are made including a strong suggestion that the Cherokee Tribe appeal both through political and legal avenues for inclusion as an affected area primarily due to projected impacts upon economy and public health as a consequence of the potential for reduced tourism

Design and Development of a Web Based Digital Repository for Scholarly Communication: A Case of NM‐AIST Tanzania

Directory of Open Access Journals (Sweden)

Wasiwasi J. Mgonzo

2014-12-01

Full Text Available Institutional repositories are essential research infrastructures for research ‐based universities. A properly dimensioned institutional repository has the potential to increase research impact and enhance the visibility of an institution through its scholarly outputs. The aim of the study reported in this paper was to design and develop a web‐based digital repository for scholarly communications using NM‐AIST as a case study. The system was developed using open source software. Findings obtained from system validation tests show that the system is a viable solution to the major challenges encountered in the management and sharing of scholarly information at the institution.

Monitoring during the stepwise implementation of the Swedish deep repository for spent fuel

International Nuclear Information System (INIS)

Baeckblom, Goeran; Almen, Karl-Erik

2004-03-01

to: obtain knowledge of undisturbed conditions in nature and their seasonal variations (baseline) in order to identify and evaluate the impact of activities related to the deep repository during different phases, obtain a better understanding of the function of the deep repository system to support the safety account and to test models and assumptions, monitor the environmental impact of the deep repository, provide evidence that the working environment is safe with regard to radiological and non-radiological effects, show that requirements on radioactive waste verification (safeguards) are fulfilled. The monitoring is concerned with bedrock conditions before and during construction and operation of the facilities, active design to engineer the underground facilities based on monitoring results during construction, the safe and environmental construction and operation of facilities. Experience exists from monitoring of the barrier function at SFR, the final repository for low - and intermediate level waste and at the Aespoe Hard Rock Laboratory and monitoring for safeguard at CLAB, the interim storage for spent nuclear fuel. The know-how on monitoring relates to all aspects from design, installation, operation and maintenance to decommissioning of systems. This report provides an overview of the features, processes and parameters that are collected during the site investigations to establish the Primary Baseline conditions for monitoring prior to the construction of the repository. It is also proposed that the monitoring programme should at least entail the following elements: objectives for the monitoring programme, scope for the monitoring (criteria for selection of issues to be monitored, identification of the properties, processes, phenomena and observable quantities to be monitored), identification on what methods to be used, operation of the monitoring system (identification of the duration and frequency of monitoring, including criteria for when monitoring may

Review. Deep repository for spent nuclear fuel SR 97 - Post-closure safety

Energy Technology Data Exchange (ETDEWEB)

Stephansson, Ove [Royal Inst. of Tech., Stockholm (Sweden). Dept. of Civil and Environmental Engineering

2000-12-01

SKB states that the chosen scenarios provide good coverage of future evolutionary pathways for the deep repository. This is not the case. SKB has not made full use of the established interaction matrices and the new method of THMC diagrams to generate the relevant and important scenarios and to construct the important pathways of variables and processes, either in the established interaction matrices and the presented THMC diagrams. Hence, SKB is demonstrating in SR 97 that they lack a well thought through, sound and solid method to select and evaluate scenarios for the purpose of demonstrating the safety of a deep repository for spent nuclear fuel. The evolution of the system is presented for the components of the repository system (fuel, canister, buffer/backfill, geosphere) and the effects of four different scenarios, but time only enters into the system for discrete events or processes, e.g. description of the relative radiotoxicity and heat decay of the fuel, temperature distribution, iron exchange process, pH in buffer, redox capacity and radionuclear release at the three sites. There is a lack of method and way of describing the evolution of the complete repository system, including the major scenarios, as a function of time. It is essential that SKB is able to: - consider the full range of potential scenarios, - grade the scenarios according to their significance for repository design and performance and safety assessment, - consider whether simple engineering actions could be taken to inhibit the development of adverse scenarios. This cannot be done with the system presented in SR 97, and so SKB do not have a full predictive capability - which is required for the engineering design of such an important and costly structure as a repository. Geoscientific investigation material for three selected sites are presented by SKB in the technical report dealing with waste, repository design and sites. Here a general overview is missing of the geological and rock

Management of radioactive waste at Novi Han Repository

International Nuclear Information System (INIS)

Stefanova, I.G.; Mateeva, M.D.; Milanov, M.V.

2002-01-01

The Novi Han Repository is the only existing repository in Bulgaria for the disposal of radioactive waste from nuclear applications in industry, medicine and research. The repository was constructed in the early sixties according to the existing requirements. It was operated by the Institute for Nuclear Research and Nuclear Energy for more than thirty years without any accident or release of radioactivity to the environment, but without any investment for upgrading. As a consequence, the Bulgarian Nuclear Safety Authority temporarily stopped the operation of the repository in 1994. The measures for upgrading the Novi Han Repository, supported by the IAEA under TC Project BUL/4/005 'Increasing Safety of Novi Han Repository', are presented in this paper. They comprise: assessment of radionuclide inventory and future waste arisings, characterisation of disposal vaults, characterisation of the site, safety assessment, upgrading of the monitoring system, option study for the selection of treatment and conditioning processes and the development of a conceptual design for low and intermediate level waste processing and storage facility, immediate measures for improvement of the existing disposal vaults and infrastructure, construction of above-ground temporary storage structures, and resuming the operation of the Novi Han Repository. The necessary activities for re-licensing of the Novi Han Repository, construction of a waste processing and storage facility and a disposal facility for spent sealed sources are discussed. (author)

CAED Document Repository

Data.gov (United States)

U.S. Environmental Protection Agency — Compliance Assurance and Enforcement Division Document Repository (CAEDDOCRESP) provides internal and external access of Inspection Records, Enforcement Actions, and...

Determination of Importance Evaluation for the ESF Enhanced Characterization of the Repository Block Cross Drift

International Nuclear Information System (INIS)

S. Goodin

2002-01-01

The objective of this DIE is to determine whether the ECRB-Cross-Drift-related activities, as identified in Section 6.0, could potentially impact (1) Yucca Mountain Site Characterization Project (YMP) testing or (2) the waste isolation capabilities of a potential repository at the Yucca Mountain site. Any controls necessary to limit such potential impacts are also identified herein

Determination of Importance Evaluation for the ESF Enhanced Charcterization of the Repository Block Cross Drift

Energy Technology Data Exchange (ETDEWEB)

S. Goodin

2002-01-09

The objective of this DIE is to determine whether the ECRB-Cross-Drift-related activities, as identified in Section 6.0, could potentially impact (1) Yucca Mountain Site Characterization Project (YMP) testing or (2) the waste isolation capabilities of a potential repository at the Yucca Mountain site. Any controls necessary to limit such potential impacts are also identified herein.

Can Web 2.0 Enhance Community Participation in an Institutional Repository? The Case of PocketKnowledge at Teachers College, Columbia University

Science.gov (United States)

Cocciolo, Anthony

2010-01-01

This project investigates if a Web 2.0 approach to designing an institutional repository can positively impact community participation. To study this, two institutional repositories (one Web 2.0, the other not) are used within the same institution. Results indicate that the use of a Web 2.0 approach significantly enhances community participation.…

An assessment of gas impact on geological repository. Methodology and material property of gas migration analysis in engineered barrier system

International Nuclear Information System (INIS)

Yamamoto, Mikihiko; Mihara, Morihiro; Ooi, Takao

2004-01-01

Gas production in a geological repository has potential hazard, as overpressurisation and enhanced release of radionuclides. Amongst data needed for assessment of gas impact, gas migration properties of engineered barriers, focused on clayey and cementitious material, was evaluated in this report. Gas injection experiments of saturated bentonite sand mixture, mortar and cement paste were carried out. In the experiments, gas entry phenomenon and gas outflow rate were observed for these materials. Based on the experimental results, two-phase flow parameters were evaluated quantitatively. A conventional continuum two-phase flow model, which is only practically used multidimensional multi-phase flow model, was applied to fit the experimental results. The simulation results have been in good agreement with the gas entry time and the outflow flux of gas and water observed in the experiments. It was confirmed that application of the continuum two-phase flow model to gas migration in cementitious materials provides sufficient degree of accuracy for assessment of repository performance. But, for sand bentonite mixture, further extension of basic two-phase flow model is needed especially for effect of stress field. Furthermore, gas migration property of other barrier materials, including rocks, but long-term gas injection test, clarification of influence of chemicals environment and large-scale gas injection test is needed for multi-barrier assessment tool development and their verification. (author)

Establishing the concept of buffer for a high-level radioactive waste repository: An approach

Energy Technology Data Exchange (ETDEWEB)

Lee, Jae Owan; Lee, Min Soo; Choi, Heui Joo [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2015-12-15

The buffer is a key component of the engineered barrier system in a high-level radioactive waste (HLW) repository. The present study reviewed the requirements and functional criteria of the buffer reported in literature, and also based on the results, proposed an approach to establish a buffer concept which is applicable to an HLW repository in Korea. The hydraulic conductivity, radionuclide-retarding capacity (equilibrium distribution coefficient and diffusion coefficient), swelling pressure, thermal conductivity, mechanical properties, organic carbon content, and initialization rate were considered as major technical parameters for the functional criteria of the buffer. Domestic bentonite (Ca-bentonite) and, as an alternative, MX-80 (Na-bentonite) were proposed for the buffer of an HLW repository in Korea. The technical specifications for those proposed bentonites were set to parameter values that conservatively satisfy Korea's functional criteria for the Ca-bentonite and Swedish criteria for the Na-bentonite. The thickness of the buffer was determined by evaluating the means of shear behavior, radionuclide release, and heat conduction, which resulted in the proper buffer thickness of 0.25 to 0.5 m. However, the final thickness of the buffer should be determined by considering coupled thermal-hydraulic-mechanical evaluation and economics and engineering aspects as well.

Selection of Corrosion Resistant Materials for Nuclear Waste Repositories

International Nuclear Information System (INIS)

R.B. Rebak

2006-01-01

Several countries are considering geological repositories to dispose of nuclear waste. The environment of most of the currently considered repositories will be reducing in nature, except for the repository in the US, which is going to be oxidizing. For the reducing repositories, alloys such as carbon steel, stainless steels and titanium are being evaluated. For the repository in the US, some of the most corrosion resistant commercially available alloys are being investigated. This paper presents a summary of the behavior of the different materials under consideration for the repositories and the current understanding of the degradation modes of the proposed alloys in ground water environments from the point of view of general corrosion, localized corrosion and environmentally assisted cracking

Numerical modeling of magma-repository interactions

NARCIS (Netherlands)

Bokhove, Onno

2001-01-01

This report explains the numerical programs behind a comprehensive modeling effort of magma-repository interactions. Magma-repository interactions occur when a magma dike with high-volatile content magma ascends through surrounding rock and encounters a tunnel or drift filled with either a magmatic

Impact of Prosthesis-Patient Mismatch on Long-term Functional Capacity After Mechanical Aortic Valve Replacement

NARCIS (Netherlands)

Petit-Eisenmann, H.; Epailly, E.; Velten, M.; Radojevic, J.; Eisenmann, B.; Kremer, H.; Kindo, M.

2016-01-01

BACKGROUND: The impact of prosthesis-patient mismatch (PPM) after aortic valve replacement (AVR) for aortic stenosis on exercise capacity remains controversial. The aim of this study was to analyze the long-term impact of PPM after mechanical AVR on maximal oxygen uptake (VO2max). METHODS: The study

Repository performance confirmation

International Nuclear Information System (INIS)

Hansen, Francis D.

2011-01-01

Repository performance confirmation links the technical bases of repository science and societal acceptance. This paper explores the myriad aspects of what has been labeled performance confirmation in U.S. programs, which involves monitoring as a collection of distinct activities combining technical and social significance in radioactive waste management. This paper is divided into four parts: (1) A distinction is drawn between performance confirmation monitoring and other testing and monitoring objectives; (2) A case study illustrates confirmation activities integrated within a long-term testing and monitoring strategy for Yucca Mountain; (3) A case study reviews compliance monitoring developed and implemented for the Waste Isolation Pilot Plant; and (4) An approach for developing, evaluating and implementing the next generation of performance confirmation monitoring is presented. International interest in repository monitoring is exhibited by the European Commission Seventh Framework Programme 'Monitoring Developments for Safe Repository Operation and Staged Closure' (MoDeRn) Project. The MoDeRn partners are considering the role of monitoring in a phased approach to the geological disposal of radioactive waste. As repository plans advance in different countries, the need to consider monitoring strategies within a controlled framework has become more apparent. The MoDeRn project pulls together technical and societal experts to assimilate a common understanding of a process that could be followed to develop a monitoring program. A fundamental consideration is the differentiation of confirmation monitoring from the many other testing and monitoring activities. Recently, the license application for Yucca Mountain provided a case study including a technical process for meeting regulatory requirements to confirm repository performance as well as considerations related to the preservation of retrievability. The performance confirmation plan developed as part of the

Citing a Data Repository: A Case Study of the Protein Data Bank.

Science.gov (United States)

Huang, Yi-Hung; Rose, Peter W; Hsu, Chun-Nan

2015-01-01

The Protein Data Bank (PDB) is the worldwide repository of 3D structures of proteins, nucleic acids and complex assemblies. The PDB's large corpus of data (> 100,000 structures) and related citations provide a well-organized and extensive test set for developing and understanding data citation and access metrics. In this paper, we present a systematic investigation of how authors cite PDB as a data repository. We describe a novel metric based on information cascade constructed by exploring the citation network to measure influence between competing works and apply that to analyze different data citation practices to PDB. Based on this new metric, we found that the original publication of RCSB PDB in the year 2000 continues to attract most citations though many follow-up updates were published. None of these follow-up publications by members of the wwPDB organization can compete with the original publication in terms of citations and influence. Meanwhile, authors increasingly choose to use URLs of PDB in the text instead of citing PDB papers, leading to disruption of the growth of the literature citations. A comparison of data usage statistics and paper citations shows that PDB Web access is highly correlated with URL mentions in the text. The results reveal the trend of how authors cite a biomedical data repository and may provide useful insight of how to measure the impact of a data repository.

The Lincoln Repository presentation: ten reasons why you should put a copy of your work in the Repository

OpenAIRE

Stainthorp, Paul

2010-01-01

Slideshow presentation created to promote the Lincoln Repository to staff at the University of Lincoln. Consists of ten reasons why academic authors should consider depositing copies of their work in the Repository.

THERMAL CONDUCTIVITY OF THE POTENTIAL REPOSITORY HORIZON

Energy Technology Data Exchange (ETDEWEB)

J.E. BEAN

2004-09-27

The primary purpose of this report is to assess the spatial variability and uncertainty of bulk thermal conductivity in the host horizon for the repository at Yucca Mountain. More specifically, the lithostratigraphic units studied are located within the Topopah Spring Tuff (Tpt) and consist of the upper lithophysal zone (Tptpul), the middle nonlithophysal zone (Tptpmn), the lower lithophysal zone (Tptpll), and the lower nonlithophysal zone (Tptpln). Design plans indicate that approximately 81 percent of the repository will be excavated in the Tptpll, approximately 12 percent in the Tptpmn, and the remainder in the Tptul and Tptpln (BSC 2004 [DIRS 168370]). This report provides three-dimensional geostatistical estimates of the bulk thermal conductivity for the four stratigraphic layers of the repository horizon. The three-dimensional geostatistical estimates of matrix and lithophysal porosity, dry bulk density, and matrix thermal conductivity are also provided. This report provides input to various models and calculations that simulate heat transport through the rock mass. These models include the ''Drift Degradation Analysis, Multiscale Thermohydrologic Model, Ventilation Model and Analysis Report, Igneous Intrusion Impacts on Waste Packages and Waste Forms, Drift-Scale Coupled Processes (DST and TH Seepage) Models'', and ''Drift Scale THM Model''. These models directly or indirectly provide input to the total system performance assessment (TSPA). The main distinguishing characteristic among the lithophysal and nonlithophysal units is the percentage of large-scale (centimeters-meters) voids within the rock. The Tptpul and Tptpll, as their names suggest, have a higher percentage of lithophysae than the Tptpmn and the Tptpln. Understanding the influence of the lithophysae is of great importance to understanding bulk thermal conductivity.

Data repositories for medical education research: issues and recommendations.

Science.gov (United States)

Schwartz, Alan; Pappas, Cleo; Sandlow, Leslie J

2010-05-01

The authors explore issues surrounding digital repositories with the twofold intention of clarifying their creation, structure, content, and use, and considering the implementation of a global digital repository for medical education research data sets-an online site where medical education researchers would be encouraged to deposit their data in order to facilitate the reuse and reanalysis of the data by other researchers. By motivating data sharing and reuse, investigators, medical schools, and other stakeholders might see substantial benefits to their own endeavors and to the progress of the field of medical education.The authors review digital repositories in medicine, social sciences, and education, describe the contents and scope of repositories, and present extant examples. The authors describe the potential benefits of a medical education data repository and report results of a survey of the Society for Directors of Research in Medicine Education, in which participants responded to questions about data sharing and a potential data repository. Respondents strongly endorsed data sharing, with the caveat that principal investigators should choose whether or not to share data they collect. A large majority believed that a repository would benefit their unit and the field of medical education. Few reported using existing repositories. Finally, the authors consider challenges to the establishment of such a repository, including taxonomic organization, intellectual property concerns, human subjects protection, technological infrastructure, and evaluation standards. The authors conclude with recommendations for how a medical education data repository could be successfully developed.

Implementation of the Brazilian national repository

International Nuclear Information System (INIS)

Tello, Cledola Cassia Oliveira de

2013-01-01

Ionizing radiation in Brazil is used in electricity generation, medicine, industry, agriculture and for research and development purposes. All these activities can generate radioactive waste. At this point, in Brazil, the use of nuclear energy and radioisotopes justifies the construction of a national repository for radioactive wastes of low and intermediate-level. According to Federal Law No. 10308, Brazilian National Commission for Nuclear Energy (CNEN) is responsible for designing and constructing the intermediate and final storages for radioactive wastes. Additionally, a restriction on the construction of Angra 3 is that the repository is under construction until its operation start, attaining some requirements of the Brazilian Environmental Regulator (IBAMA). The RBMN Project (Repository for Low and Intermediate-Level Radioactive Wastes) aims at the implantation of a National Repository for disposal of low and intermediate-level of radiation wastes. This Project has some aspects that are unique in the Brazilian context, especially referring to the time between its construction and the end of its institutional period. This time is about 360 years, when the area will be released for unrestricted uses. It means that the Repository must be safe and secure for more than three hundred years, which is longer than half of the whole of Brazilian history. This aspect is very new for the Brazilian people, bringing a new dimension to public acceptance. Another point is this will be the first repository in South America, bringing a real challenge for the continent. The current status of the Project is summarized. (author)

The development of safeguards for geological repositories

International Nuclear Information System (INIS)

Van der Meer, K.

2009-01-01

Traditionally, research and development on geological repositories for High Level Waste (HLW) focuses on the short- and long-term safety aspects of the repository. If the repository will also be used for the disposal of spent fuel, safeguards aspects have to be taken into account. Safety and safeguards requirements may be contradictory; the safety of a geological repository is based on the non-intrusion of the geological containment, while safeguards require regular inspections of position and amount of the spent fuel. Examples to reconcile these contradictory requirements are the use of information required for the safety assessment of the geological repository for safeguards purposes and the adaptation of the safeguards approach to use non-intrusive inspection techniques. The principles of an inspection approach for a geological repository are now generally accepted within the IAEA. The practical applicability of the envisaged inspection techniques is still subject to investigation. It is specifically important for the Belgian situation that an inspection technique can be used in clay, the geological medium in which Belgium intends to dispose its HLW and spent fuel. The work reported in this chapter is the result of an international cooperation in the framework of the IAEA, in which SCK-CEN participates

Investigative study of standards for digital repositories and related services

CERN Document Server

Foulonneau, Muriel; Badolato, Anne-Marie

2008-01-01

This study is meant for institutional repository managers, service providers, repository software developers and generally, all players taking an active part in the creation of the digital repository infrastructure for e-research and e-learning. It reviews the current standards, protocols and applications in the domain of digital repositories. Special attention is being paid to the interoperability of repositories to enhance the exchange of data in repositories. It aims to stimulate discussion about these topics and supports initiatives for the integration of and, where needed, development of

Sorption on inactive repository components

International Nuclear Information System (INIS)

Gardiner, M.P.; Smith, A.J.; Williams, S.J.

1990-11-01

The near-field of an intermediate level/low level radioactive waste repository will contain significant quantities of iron and steel, Magnox and Zircaloy. Their corrosion products may possess significant sorption capacity for radioelements. The sorption of americium and plutonium onto magnesium hydroxide, zirconium hydroxide, colloidal magnetite and colloidal haematite has been studied under conditions typical of the porewater of a cementitious near-field. R D values ≥ 10 5 m g -1 were measured for both actinides on the oxides and hydroxides. These values are at least as great as those measured on crushed 3:1 Blast Furnace Slag/Ordinary Portland cement. Competitive sorption experiments have shown that sorption onto the corrosion products does not take place in preference to that on the cement or the converse. Magnetite and haematite colloids are positively charged in cement-equilibrated water whilst zirconium hydroxide is negatively charged. Crushed cement was found to be positively charged. Simple experiments show that only a small proportion of haematite colloids is potentially mobile through a column of crushed cement. (author)

Sorption on inactive repository components

International Nuclear Information System (INIS)

Gardiner, M.P.; Smith, A.J.; Williams, S.J.

1990-07-01

The near-field of an intermediate level/low level radioactive waste repository will contain significant quantities of iron and steel, Magnox and Zircaloy. Their corrosion products may possess significant sorption capacity for radioelements. The sorption of americium and plutonium onto magnesium hydroxide, zirconium hydroxide, colloidal magnetite and colloidal haematite has been studied under conditions typical of the porewater of a cementitious near-field. R D values ≥ 10 5 ml g -1 were measured for both actinides on the oxides and hydroxides. These values are at least as great at those measured on crushed 3:1 Blast Furnace Slag/Ordinary Portland Cement. Competitive sorption experiments have shown that sorption onto the corrosion products does not take place in preference to that on the cement or the converse. Magnetite and haematite colloids are positively charged in cement-equilibrated water whilst zirconium hydroxide is negatively charged. Crushed cement was found to be positively charged. Simple experiments show that only a small proportion of haematite colloids is potentially mobile through a column of crushed cement. (author)

Refinancing of the search for a repository and of the repository for heat generating radioactive Waste. Pt. 2

International Nuclear Information System (INIS)

Moench, Christoph

2013-01-01

Part I of this article, which appeared in the preceding issue, described in general terms the background to the search for a disposal site and the result of the exploration to date of the repository, which would appear to be suitable from a mining standpoint according to the present knowledge. According to the rules in effect up to now, the exploration and construction would be financed by advance payments on the contributions of the waste producing companies, in particular the utility companies. The working draft of an 'Act on the search for and selection of a site for a repository for heat generating radioactive waste' (Gesetz zur Suche und Auswahl eines Standortes fuer ein Endlager fuer waermeentwickelnde radioaktive Abfaelle) from autumn 2012 provides for a new version of section 21b Atomic Energy Act, under which the costs for 'carrying out a repository selection procedure pursuant to the Repository Selection Act (Standort-auswahlgesetz)' would be allocated to the future users of the repository who are obliged to make contributions as a 'necessary expense'. Part II evaluates this provision of the working draft on the basis of the financial constitutional law. A comparison of sites is not a measure that could be allocated to the future users of the repository who are obliged to make contributions as a 'necessary expense'. Moreover, there is a lack of responsibility for the financing and of a legally relevant advantage that would be conferred by a cumulative alternative repository search for the later users of the repository who are obliged to provide the pre-financing. The costs can therefore not be allocated to the later users as either a contribution or a special charge, not even by way of an association with mandatory membership (Zwangsverband). They must be borne by the state. Consequently, the allocation stipulated by provision would constitute an impermissible charge under financial constitutional law. (orig.)

Institutional Repositories as Infrastructures for Long-Term Preservation

Science.gov (United States)

Francke, Helena; Gamalielsson, Jonas; Lundell, Björn

2017-01-01

Introduction: The study describes the conditions for long-term preservation of the content of the institutional repositories of Swedish higher education institutions based on an investigation of how deposited files are managed with regards to file format and how representatives of the repositories describe the functions of the repositories.…

Radionuclide getters in the near-field chemistry of repositories

International Nuclear Information System (INIS)

Holland, T.R.; Lee, D.J.

1991-06-01

The solubility of many radionuclides in a radwaste repository will be limited by the high pH of the cement based system. However, the inclusion of specific sorbing media, within the cement backfill, offers the ability to improve the retention of the more mobile radionuclides, such as caesium and iodine; thereby further reducing their environmental impact. This programme of work is intended to assess the radionuclide sorption efficiency of selected inorganic getters incorporated in cement. (author)

Electronic Repository of Russian Historical Statistics

NARCIS (Netherlands)

Tykhonov, Vyacheslav; Kessler, Gijs; Markevich, Andrei; de Vries, Jerry

2014-01-01

The Electronic Repository for Russian Historical Statistics brings together data extracted from various published and unpublished sources in one place. Its principal focus is Russian economic and social history of the last three centuries (18th-21st). The repository caters to the needs of the

Stress, strain, and temperature induced permeability changes in potential repository rocks

International Nuclear Information System (INIS)

Heard, H.C.; Duba, A.

1977-01-01

Work is in progress to assess the permeability characteristics of coarse-grained igneous rocks as affected by pressure, deviatoric stress, and temperature. In order to predict the long-term behavior of these rocks, both virgin and fractured, permeability and all principal strains resulting from an imposed deviatoric stress under various simulated lithostatic pressures are being measured. In addition, compressional as well as shear velocities and electrical conductivity are being evaluated along these principal directions. These simultaneous measurements are being made initially at 25 0 C on a 15 cm diameter by 30 cm long sample in a pressure apparatus controlled by a mini-computer. Correlation of these data with similar field observations should then allow simplified exploration for a suitable repository site as well as the prediction of the response of a mined cavity with both distance and time at this site. After emplacement of the waste canisters, the mechanical stability and hydrologic integrity of this mined repository will be directly influenced by the fracturing of the surrounding rock which results from local temperature differences and the thermal expansion of that rock. Temperatures (and, hence, these differences) in the vicinity of the repository are expected to be affected by the presence of pore fluids (single- or two-phase) in the rock, the heat capacity and the thermal conductivity of this system. In turn, these are all dependent upon lithostatic pressure, pore pressure, and stress. Thermal expansion (and fracturing) will also be affected by the lithostatic (and effective) pressure, the deviatoric stress field, and the initial anisotropy of the rock

Fons antic i repositoris universitaris a Espanya

Directory of Open Access Journals (Sweden)

Herrera Morillas, José Luis

2015-12-01

Full Text Available Es mostra la presència de col·leccions de fons antic en els repositoris de les biblioteques universitàries espanyoles després d'analitzar tots els repositoris. Per a aquesta anàlisi, com a part de la metodologia emprada, s'ha elaborat un model o llista que consta d'onze elements. Del conjunt de les universitats espanyoles, seixanta tenen repositoris, vint-i-vuit dels quals (16,8 % disposen de col·leccions de fons antic. Com que del concepte de repositori institucional no sembla desprendre's que tingui com a finalitat incloure aquest tipus de col·leccions, es reflexiona sobre la peculiaritat que una part dels repositoris universitaris espanyols inclogui col·leccions d'aquestes característiques.Se muestra la presencia de colecciones de fondo antiguo en los repositorios de las bibliotecas universitarias españolas después de analizar todos los repositorios. Para este análisis, como parte de la metodología empleada, se ha elaborado un modelo o lista que consta de once elementos. Del conjunto de las universidades españolas, sesenta cuentan con repositorios y, de estos, veintiocho (16,8 % disponen de colecciones de fondo antiguo. Debido a que del concepto de repositorio institucional no parece desprenderse que tenga como finalidad albergar este tipo de colecciones, se hace una reflexión sobre la peculiaridad de que parte de los repositorios universitarios españoles incluya colecciones de estas características.This paper uses an analysis of the repositories of Spanish universities to identify which institutions contain rare book and manuscript collections. The method used in this analysis involved examining each university on the basis of a list comprising eleven elements. A total of 60 universities were found to have repositories but only 28 (16.8 % of these contained rare book and manuscript collections. In the light of these figures, which suggest that Spanish university repositories do not generally consider the preservation of rare

Impact of three years training on operations capacities of research ethics committees in Nigeria.

Science.gov (United States)

Folayan, Morenike Oluwatoyin; Adaranijo, Aisha; Durueke, Florita; Ajuwon, Ademola; Adejumo, Adebayo; Ezechi, Oliver; Oyedeji, Kola; Akanni, Olayide

2014-04-01

This paper describes a three-year project designed to build the capacity of members of research ethics committes to perform their roles and responsibilities efficiently and effectively. The project participants were made up of a cross-section of the membership of 13 Research Ethics Committees (RECs) functioning in Nigeria. They received training to develop their capacity to evaluate research protocols, monitor trial implementation, provide constructive input to trial staff, and assess the trial's success in promoting community engagement in the research. Following the training, technical assistance was provided to participants on an ongoing basis and the project's impacts were assessed quantitatively and qualitatively. Results indicate that sustained investment in capacity building efforts (including training, ongoing technical assistance, and the provision of multiple tools) improved the participants' knowledge of both the ethical principles relevant to biomedical research and how effective REC should function. Such investment was also shown to have a positive impact on the knowledge levels of other RECs members (those who did not receive training) and the overall operations of the RECs to which the participants belonged. Building the capacity of REC members to fulfill their roles effectively requires sustained effort and investment and pays off by enabling RECs to fulfill their essential mission of ensuring that trials are conducted safely and ethically. © 2012 John Wiley & Sons Ltd.

Decompression of magma into repository tunnels

NARCIS (Netherlands)

Bokhove, Onno; Woods, A.W.

2002-01-01

It is nontrivial to find and design safe repository sites for nuclear waste. It appears common sense to drill tunnels as repository sites in a mountain in remote and relatively dry regions. However, erosion of the waste canisters by naturally abundant chemicals in the mountains water cycle remains a

Paper and digital repositories in the United States

Directory of Open Access Journals (Sweden)

David F. Kohl

2003-09-01

Full Text Available What you've asked me to talk about today is basically what can libraries do with all the stuff they have and continue to get. Where do we put it all; what do we do with it? As we know, libraries have three core functions: collecting, organizing and preserving the key documents of the human enterprise. And, with apologies to Saint Paul, the greatest of these is preservation. For without preservation neither of the first two ultimately matter. My assignment this morning is to bring you up to date on one specific aspect of the preservation function, library repositories, and indeed, library repository developments in the US. The plan for this morning's presentation is the following: after a brief background review to give us a context for American developments we will examine first the various kinds of print repositories and then the various initiatives for electronic repositories. Because other presentations at this conference deal with electronic repositories, the main focus today will be on U.S. print repositories.

Institutional Repository Sebagai Sarana Komunikasi Ilmiah Yang Sustainable Dan Reliable

Directory of Open Access Journals (Sweden)

Faizuddin Harliansyah

2016-07-01

Full Text Available Abstract; Institutional repositories development has drawn the attention of many scholars throughout the world. Using the keywords ‘institutional repositories’, there are over 300 peer-reviewed articles related on the topic has been indexed in Library, Information Science, & Technology Abstracts (LISTA and SCOPUS. There are also hundreds of theses, dissertations, and websites dedicated on this blooming trends. These are proofs that the importance of IR in higher education has been acknowledged by many professionals in the field. This paper aims at clarifying the role of repositories in strengthening scholarly communication in higher education and research institution and explaining some basic repositories concepts (types of repositories and their characteristics, as well as exploring its relations with open access movement, the development ideas, and resources that could be kept in repositories and deposit policies. Abstrak; Pengembangan institutional repositories telah banyak menyita perhatian dari kalangan ilmiah di seluruh dunia. Melalui kata kunci ‘institutional repositories’, ada lebih dari 300 artikel terulas mitra bestari yang berhubungan dengan topik ini, yang telah terindeks di Library, Information Science, & Technology Abstracts (LISTA, dan SCOPUS. Terdapat juga ratusan tesis, disertasi, dan website yang mengulas trend ini. Inilah bukti bahwa pentingnya institutional repositories (IR telah dipahami oleh para profesional di bidangnya. Tulisan ini akan menjelaskan aturan-aturan repository dalam memperkuat komunikasi ilmiah di perguruan tinggi dan lembaga riset, menjelaskan konsep-konsep dasar repositories, termasuk tipe-tipe repository dan karakteristiknya. Tulisan ini juga akan memperdalam konsep repositories dalam hubungannya dengan gerakan open access, pengembangan ide-ide, sumber-sumber ilmiah yang dapat disimpan di repositories, serta kebijakan penyimpanan di dalamnya.

Environmental issues of repository licensing: an evaluation of a hypothetical high-level radioactive waste repository

International Nuclear Information System (INIS)

Owen, J.L.; McGinnis, J.T.; Harper, C.M.; Battelle Columbus Labs., OH)

1982-01-01

This paper presents results of an environmental assessment conducted under the direction of the Office of Nuclear Waste Isolation as part of the National Waste Terminal Storage program. The study defined a range of potential environmental effects of constructing, operating, decommissioning, and long-term isolation of a nuclear waste repository. The analytical methodology used to determine potential environmental effects required definition of a hypothetical environmental setting and repository. Potentially applicable regulatory requirements were identified and were used as guidelines to evaluate permitting feasibility. The environmental effects of repository development were analyzed for the two major time periods of concern: short term (the period of construction, operation, and decommissioning) and long term (the isolation period after decommissioning). As a result of this analysis, major environmental uncertainties and issues were identified. 11 references, 5 figures

Analysis of computational vulnerabilities in digital repositories

Directory of Open Access Journals (Sweden)

Valdete Fernandes Belarmino

2015-04-01

Full Text Available Objective. Demonstrates the results of research that aimed to analyze the computational vulnerabilities of digital directories in public Universities. Argues the relevance of information in contemporary societies like an invaluable resource, emphasizing scientific information as an essential element to constitute scientific progress. Characterizes the emergence of Digital Repositories and highlights its use in academic environment to preserve, promote, disseminate and encourage the scientific production. Describes the main software for the construction of digital repositories. Method. The investigation identified and analyzed the vulnerabilities that are exposed the digital repositories using Penetration Testing running. Discriminating the levels of risk and the types of vulnerabilities. Results. From a sample of 30 repositories, we could examine 20, identified that: 5% of the repositories have critical vulnerabilities, 85% high, 25% medium and 100% lowers. Conclusions. Which demonstrates the necessity to adapt actions for these environments that promote informational security to minimizing the incidence of external and / or internal systems attacks.Abstract Grey Text – use bold for subheadings when needed.

New Roles, New Responsibilities: Examining Training Needs of Repository Staff

Directory of Open Access Journals (Sweden)

Natasha Simons

2012-05-01

Full Text Available INTRODUCTION Institutional repositories play a critical role in the research lifecycle. Funding agencies are increasingly seeking an improved return on their investment in research. Repositories facilitate this process by providing storage of, and access to, institutional research outputs and, more recently, research data. While repositories are generally managed within the academic library, repository staff require different skills and knowledge compared with traditional library roles. This study reports on a survey of Australasian institutional repository staff to identify skills and knowledge sets. METHODS Institutional repository staff working at universities in Australia and New Zealand were invited to participate in an online survey which incorporated both open and closed-ended question types. RESULTS The survey found significant gaps in the current provision of formal training and coursework related to institutional repositories, which echoed findings in the United Kingdom, Italy, and the United States. DISCUSSION There is clearly a need for more and varied training opportunities for repository professionals. Repository work requires a specific set of skills that can be difficult to find and institutions will benefit from investing in training and ongoing development opportunities for repository staff. CONCLUSION The data from this study could be used to facilitate staff recruitment, development, training, and retention strategies.

Evaluation of repository safety

Energy Technology Data Exchange (ETDEWEB)

Sagar, B.; Patrick, W.; Dasgupta, B.; Mohanty, S. [Center for Nuclear Waste Regulatory Analyses, San Antonio (United States)

2002-07-01

The United States high-level waste program requires evaluation of radiological safety during two distinct time intervals. The first interval, commonly referred to as the preclosure period, deals with receipt of waste at the site, transfer into disposal containers, if needed, emplacement in the underground openings, monitoring and maintenance activities, backfill and closure of the underground openings, and decontamination and decommissioning of the surface facilities of the geologic repository. The preclosure period may extend from a few tens of years to as long as a few hundred of years, depending on repository design and societal norms regarding a final decision to permanently seal the repository. During the preclosure or operational period, performance confirmation studies are conducted to provide a basis for updating and reevaluating estimates of postclosure performance and, finally, to provide a basis for a closure decision. The postclosure period during which expected repository performance must meet certain standards may range from ten thousands years, as it does in the United States, to millions of years, as it does in some European nations. Waste handling operations in the preclosure period are to be evaluated in relation to their potential effect on workers, members of general public, and the general environment. During this period, releases of radioactivity are to be monitored and appropriate actions taken whenever established limits are approached or exceeded. Preclosure safety is highly dependent on facility design, operational hardware and automated systems, operational sequences, and reliability of humans involved in operations. Preclosure safety analyses conducted before operations begin play a major role in the design process, selection of equipment, and development of operational procedures. Because of the complexity, duration, and spatial scales of the operations, analyses are conducted using mathematical models implemented in computer codes

Evaluation of repository safety

International Nuclear Information System (INIS)

Sagar, B.; Patrick, W.; Dasgupta, B.; Mohanty, S.

2002-01-01

The United States high-level waste program requires evaluation of radiological safety during two distinct time intervals. The first interval, commonly referred to as the preclosure period, deals with receipt of waste at the site, transfer into disposal containers, if needed, emplacement in the underground openings, monitoring and maintenance activities, backfill and closure of the underground openings, and decontamination and decommissioning of the surface facilities of the geologic repository. The preclosure period may extend from a few tens of years to as long as a few hundred of years, depending on repository design and societal norms regarding a final decision to permanently seal the repository. During the preclosure or operational period, performance confirmation studies are conducted to provide a basis for updating and reevaluating estimates of postclosure performance and, finally, to provide a basis for a closure decision. The postclosure period during which expected repository performance must meet certain standards may range from ten thousands years, as it does in the United States, to millions of years, as it does in some European nations. Waste handling operations in the preclosure period are to be evaluated in relation to their potential effect on workers, members of general public, and the general environment. During this period, releases of radioactivity are to be monitored and appropriate actions taken whenever established limits are approached or exceeded. Preclosure safety is highly dependent on facility design, operational hardware and automated systems, operational sequences, and reliability of humans involved in operations. Preclosure safety analyses conducted before operations begin play a major role in the design process, selection of equipment, and development of operational procedures. Because of the complexity, duration, and spatial scales of the operations, analyses are conducted using mathematical models implemented in computer codes

Semantic Linking of Learning Object Repositories to DBpedia

Science.gov (United States)

Lama, Manuel; Vidal, Juan C.; Otero-Garcia, Estefania; Bugarin, Alberto; Barro, Senen

2012-01-01

Large-sized repositories of learning objects (LOs) are difficult to create and also to maintain. In this paper we propose a way to reduce this drawback by improving the classification mechanisms of the LO repositories. Specifically, we present a solution to automate the LO classification of the Universia repository, a collection of more than 15…

NIDDK Central Repository

Data.gov (United States)

U.S. Department of Health & Human Services — The NIDDK Central Repository stores biosamples, genetic and other data collected in designated NIDDK-funded clinical studies. The purpose of the NIDDK Central...

Generic Repository Concepts and Thermal Analysis for Advanced Fuel Cycles - 12477

Energy Technology Data Exchange (ETDEWEB)

Hardin, Ernest [Sandia National Laboratories, P.O. Box 5800 MS 0736, Albuquerque, NM 87185 (United States); Blink, James [Lawrence Livermore National Laboratory, P.O. Box 808, Livermore, CA 94551-0808 (United States); Carter, Joe [Savannah River National Laboratory, Savannah River Site, Aiken, SC 29808 (United States); Fratoni, Massimiliano; Greenberg, Harris; Sutton, Mark [Lawrence Livermore National Laboratory (United States); Howard, Robert [Oak Ridge National Laboratory, P.O. Box 2008, Oak Ridge, TN 37831 (United States)

2012-07-01

A geologic disposal concept for spent nuclear fuel (SNF) or high-level waste (HLW) consists of three components: waste inventory, geologic setting, and concept of operations. A set of reference geologic disposal concepts has been developed by the U.S. Department of Energy (DOE), Used Fuel Disposition campaign. Reference concepts are identified for crystalline rock, clay/shale, bedded salt, and deep borehole (crystalline basement) geologic settings. These were analyzed for waste inventory cases representing a range of waste types that could be produced by advanced nuclear fuel cycles. Concepts of operation consisting of emplacement mode, repository layout, and engineered barrier descriptions, were selected based on international progress. All of these disposal concepts are enclosed emplacement modes, whereby waste packages are in direct contact with encapsulating engineered or natural materials. Enclosed modes have less capacity to dissipate heat than open modes such as that proposed for a repository at Yucca Mountain. Thermal analysis has identified important relationships between waste package size and capacity, and the duration of surface decay storage needed to meet temperature limits for different disposal concepts. For the crystalline rock and clay/shale repository concepts, a waste package surface temperature limit of 100 deg. C was assumed to prevent changes in clay-based buffer material or clay-rich host rock. Surface decay storage of 50 to 100 years is needed for disposal of high-burnup LWR SNF in 4-PWR packages, or disposal of HLW glass from reprocessing LWR uranium oxide (UOX) fuel. High-level waste (HLW) from reprocessing of metal fuel used in a fast reactor could be disposed after decay storage of 50 years or less. For disposal in salt the rock thermal conductivity is significantly greater, and higher temperatures (200 deg. C) can be tolerated at the waste package surface. Decay storage of 10 years or less is needed for high-burnup LWR SNF in 4-PWR

Source term evaluation model for high-level radioactive waste repository with decay chain build-up.

Science.gov (United States)

Chopra, Manish; Sunny, Faby; Oza, R B

2016-09-18

A source term model based on two-component leach flux concept is developed for a high-level radioactive waste repository. The long-lived radionuclides associated with high-level waste may give rise to the build-up of activity because of radioactive decay chains. The ingrowths of progeny are incorporated in the model using Bateman decay chain build-up equations. The model is applied to different radionuclides present in the high-level radioactive waste, which form a part of decay chains (4n to 4n + 3 series), and the activity of the parent and daughter radionuclides leaching out of the waste matrix is estimated. Two cases are considered: one when only parent is present initially in the waste and another where daughters are also initially present in the waste matrix. The incorporation of in situ production of daughter radionuclides in the source is important to carry out realistic estimates. It is shown that the inclusion of decay chain build-up is essential to avoid underestimation of the radiological impact assessment of the repository. The model can be a useful tool for evaluating the source term of the radionuclide transport models used for the radiological impact assessment of high-level radioactive waste repositories.

Capacity subscription and its market design impact

International Nuclear Information System (INIS)

Doorman, Gerard; Solem, Gerd

2005-04-01

Capacity Subscription (CS) implies that consumers buy (subscribe to) a certain amount of capacity. Their demand is limited to this capacity when the total power system is short of capacity and the System Operator activates controllable Load Limiting Devices (LLDs). The objective is to maintain system security by avoiding involuntary load shedding. The report describes a market design with CS. As a case study, an analysis is made of the changes in the market design of the Nordic system that would be necessary to implement CS. First the present Nordic market design is described. Focus is on the various market participants, their roles within various time horizons and their interactions. So it is described how CS works, why it works and what is necessary to make it work. Subsequently the necessary changes in the Nordic market structure are described. The major changes are the installation of the LLDs, the establishment of the necessary infrastructure to control the LLDs and the rules governing their control and the establishment of a capacity market. The major rule is that the System Operator announces LLD activation when a shortage situation is expected. In the capacity market generators offer available capacity during system peak conditions, while consumers bid their need for capacity. Market participants are the same as on the spot market, while small consumers buy through retailer. Generators are obliged to offer the capacity sold on the capacity market on the spot market during LLD activation. Failure to do so results in a penalty payment. The report further discusses issues like the need for verification procedures, import and export, generation pooling, the handling of small consumers, reserves and a possible implementation path of CS. With respect to transmission constraints it is argued that market splitting can be a viable option. It is concluded that CS can be a possible solution to maintain generation adequacy, but there are some serious challenges. The

Researching radioactive waste disposal. [Underground repository

Energy Technology Data Exchange (ETDEWEB)

Feates, F; Keen, N [UKAEA Research Group, Harwell. Atomic Energy Research Establishment

1976-02-16

At present it is planned to use the vitrification process to convert highly radioactive liquid wastes, arising from nuclear power programme, into glass which will be contained in steel cylinders for storage. The UKAEA in collaboration with other European countries is currently assessing the relative suitability of various natural geological structures as final repositories for the vitrified material. The Institute of Geological Sciences has been commissioned to specify the geological criteria that should be met by a rock structure if it is to be used for the construction of a repository though at this stage disposal sites are not being sought. The current research programme aims to obtain basic geological data about the structure of the rocks well below the surface and is expected to continue for at least three years. The results in all the European countries will then be considered so that the United Kingdom can choose a preferred method for isolating their wastes. It is only at that stage that a firm commitment may be made to select a site for a potential repository, when a far more detailed scientific research study will be instituted. Heat transfer problems and chemical effects which may occur within and around repositories are being investigated and a conceptual design study for an underground repository is being prepared.

Cross Institutional Cooperation on a Shared Bit Repository

DEFF Research Database (Denmark)

Zierau, Eld; Kejser, Ulla Bøgvad

2013-01-01

This paper explores how independent institutions, such as archives and libraries, can cooperate on managing a shared bit repository with bit preservation, in order to use their resources for preservation in a more cost-effective way. It uses the OAIS Reference Model to provide a framework...... for systematically analysing institutions technical and organisational requirements for a remote bit repository. Instead of viewing a bit repository simply as Archival Storage for the institutions repositories, we argue for viewing it as consisting of a subset of functions from all entities defined by the OAIS...... Reference Model. The work is motivated by and used in a current Danish feasibility study for establishing a national bit repository. The study revealed that depending on their missions and the collections they hold, the institutions have varying requirements e.g. for bit safety, accessibility...

Cross Institutional Cooperation on a Shared Bit Repository

DEFF Research Database (Denmark)

Zierau, Eld; Kejser, Ulla Bøgvad

2010-01-01

This paper explores how independent institutions, such as archives and libraries, can cooperate on managing a shared bit repository with bit preservation in order to use their resources for preservation n in a more cost-effective way. It uses the OAIS Reference Model to provide a framework...... for systematically analysing the technical and organizational requirements of institutions for a remote bit repository. Instead of viewing a bit repository simply as Archival Storage for the institutions’ repositories, we argue for viewing it as consisting of a subset of functions from all entities defined...... by the OAIS Reference Model. The work is motivated by and used in a current Danish feasibility study for establishing a national bit repository. The study revealed that depending on their missions and the collections they hold, the institutions have varying requirements, such as for bit safety, accessibility...

Emplacement and retrieval equipment design considerations for a repository in salt

International Nuclear Information System (INIS)

Nair, B.R.; Bahorich, R.J.

1987-01-01

The current design concept for the disposal of nuclear high level waste packages in a repository in salt is based on the emplacement of individual packages in vertical boreholes in the underground mine floor. A key requirement is that the waste packages be capable of being retrieved during the last 26 years of the 76-year repository operating period. The unique design considerations relating to the retrieval of waste packages emplaced in bedded salt are presented in this paper. The information is based on the experience developed during the design of vertical emplacement and retrieval equipment in support of the Sandia Defense High Level Waste experiments at the Waste Isolation Pilot Plant. Also included are the impact of retrievability on the design of the equipment, the special salt cutting technology that was developed for this application, and a description of the equipment

MRS system study for the repository: Yucca Mountain Site Characterization Project

International Nuclear Information System (INIS)

Sinagra, T.A.; Harig, R.

1990-12-01

The US Department of Energy (DOE), Office of Civilian Radioactive Waste Management (OCRWM), has initiated a waste management system study to identify the impacts of the presence or absence of a monitored retrievable storage facility (hereinafter referred to as ''MRS'') on system costs and program schedules. To support this study, life-cycle cost estimates and construction schedules have been prepared for the surface and underground facilities and operations geologic nuclear waste repository at Yucca Mountain, Nye County, Nevada. Nine different operating scenarios (cases) have been identified by OCRWM for inclusion in this study. For each case, the following items are determined: the repository design and construction costs, operating costs, closure and decommissioning costs, required staffing, construction schedules, uncertainties associated with the costs and schedules, and shipping cask and disposal container throughputs. This document contains A-D

MRS system study for the repository: Yucca Mountain Site Characterization Project

International Nuclear Information System (INIS)

Sinagra, T.A.; Harig, R.

1990-12-01

The US Department of Energy (DOE), Office of Civilian Radioactive Waste Management (OCRWM), has initiated a waste management system study to identify the impacts of the presence or absence of a monitored retrievable storage facility (hereinafter referred to as ''MRS'') on system costs and program schedules. To support this study, life-cycle cost estimates and construction schedules have been prepared for the surface and underground facilities and operations of a geologic nuclear waste repository at Yucca Mountain, Nye County, Nevada. Nine different operating scenarios (cases) have been identified by OCRWM for inclusion in this study. For each case, the following items are determined: the repository design and construction costs, operating costs, closure and decommissioning costs, required staffing, construction schedules, uncertainties associated with the costs and schedules, and shipping cask and disposal container throughputs. 6 refs., 83 figs., 57 tabs

Office of Civilian Radioactive Waste Management: Annual capacity report

International Nuclear Information System (INIS)

1988-06-01

The system configuration used as the basis for this year's report is the authorized system defined in the Mission Plan Amendment. It includes a Monitored Retrievable Storage (MRS) facility as an integral system component. The illustrative waste acceptance schedule for this WMS configuration reflects the amended first repository schedule and a proposed schedule for the MRS facility. This schedule provides only an approximation of when and how the system may operate and is subject to changes as recognized in the draft Mission Plan Amendment. During the first 10 years of WMS operation, the total quantity of spent fuel that could be accepted is projected to be 24,100 metric tons uranium (MTU). The allocation of acceptance rights is currently based on the projected annual capacity of the WMS to receive SNF and the age of permanently discharged spent fuel as determined from 1986 data provided by the Purchasers of waste disposal services on the 1987 Nuclear Fuel Data Form, RW-859. The allocations are based on assigning the highest priority to the oldest fuel on an industry-wide basis. The Annual Capacity Report (ACR) provides a discussion of the requirement for the ACR and the role it plays in DOE's interaction with the Purchasers in implementing the provisions of the Standard Disposal Contract. The currently projected annual acceptance capacity to be allocated and a discussion of some of the impacts the Nuclear Waste Policy Amendments Act of 1987 may have on the Purchasers, DOE, and the Contract are presented. The basis and procedure for allocating this capacity (acceptance rights) are discussed. The status of the ACR Issue Resolution Process and DOE responses to comments on the 1987 ACR are discussed. 7 refs

Tools for Managing Repository Objects

OpenAIRE

Banker, Rajiv D.; Isakowitz, Tomas; Kauffman, Robert J.; Kumar, Rachna; Zweig, Dani

1993-01-01

working Paper Series: STERN IS-93-46 The past few years have seen the introduction of repository-based computer aided software engineering (CASE) tools which may finally enable us to develop software which is reliable and affordable. With the new tools come new challenges for management: Repository-based CASE changes software development to such an extent that traditional approaches to estimation, performance, and productivity assessment may no longer suffice - if they ever...

Establishing a site for A Slovenian LILW repository - 16151

International Nuclear Information System (INIS)

VIRSEK, SANDI; SPILER, JANJA; VESELIC, MIRAN

2009-01-01

In this paper we will describe the practice and siting process for a LILW repository in Slovenia. Slovenia is a small country, and, consequently, its nuclear programme is small. It does include almost everything that large programmes have, but we still do not have a repository. In 2004, the Slovenian Radwaste management agency (ARAO) initiated a new procedure to find a proper location for a LILW repository. ARAO asked all Slovenian communities to participate. All communities have the option to withdraw from the process until they have approved the site. We received eight responses, and we prepared methodologies with different parameters to evaluate all potential sites. All sites were assessed by Slovenian experts, and determinations were based on using prepared methodologies. On the basis of their expert opinions, we prepared a pre-feasibility study and chose the three most suitable sites. With these three we continued the process. After that time, one of the communities withdrew from the procedure, and another one reversed its proposed site and proposed a new one. For the third site we continued with the programme, and we prepared a feasibility study with a Strategic Environmental Impact Assessment and preliminary safety calculations for the comparison of different concepts of disposal units. If everything goes according to the plan for this site and the concept, we expect site approval in the first half of 2009. After that, we will start preparing everything necessary for building permission. (authors)

Encapsulation plant preliminary design, phase 2. Repository connected facility

International Nuclear Information System (INIS)

Kukkola, T.

2006-12-01

The disposal facility of the spent nuclear fuel will be located in Olkiluoto. The encapsulation plant is a part of the disposal facility. In this report, an independent encapsulation plant is located above the underground repository. In the encapsulation plant, the spent fuel is received and treated for disposal. In the fuel handling cell, the spent fuel assemblies are unloaded from the spent fuel transport casks and loaded into the disposal canisters. The gas atmosphere of the disposal canister is changed, the bolted inner canister lid is closed, and the electron beam welding method is used to close the lid of the outer copper canister. The disposal canisters are cleaned and transferred into the buffer store after the machining and inspection of the copper lid welds. From the buffer store, the disposal canisters are transferred into the repository spaces by help of the canister lift. All needed stages of operation are to be performed safely without any activity releases or remarkable personnel doses. The bentonite block interim storage is associated with the encapsulation plant. The bentonite blocks are made from bentonite powder. The bentonite blocks are used as buffer material around the disposal canister in the deposition hole. The average production rate of the encapsulation plant is 40 canisters per year. The nominal maximum production capacity is 100 canisters per year in one shift operation. (orig.)

Gas cooled reactor decommissioning. Packaging of waste for disposal in the United Kingdom deep repository

International Nuclear Information System (INIS)

Barlow, S.V.; Wisbey, S.J.; Wood, P.

1998-01-01

United Kingdom Nirex Limited has been established to develop and operate a deep underground repository for the disposal of the UK's intermediate and certain low level radioactive waste. The UK has a significant Gas Cooled Reactor (GCR) programme, including both Magnox and AGR (Advanced Gas-cooled Reactor) capacity, amounting to 26 Magnox reactors, 15 AGR reactors as well as research and prototype reactor units such as the Windscale AGR and the Windscale Piles. Some of these units are already undergoing decommissioning and Nirex has estimated that some 15,000 m 3 (conditioned volume) will come forward for disposal from GCR decommissioning before 2060. This volume does not include final stage (Stage 3) decommissioning arisings from commercial reactors since the generating utilities in the UK are proposing to adopt a deferred safe store strategy for these units. Intermediate level wastes arising from GCR decommissioning needs to be packaged in a form suitable for on-site interim storage and eventual deep disposal in the planned repository. In the absence of Conditions for Acceptance for a repository in the UK, the dimensions, key features and minimum performance requirements for waste packages are defined in Waste Package Specifications. These form the basis for all assessments of the suitability of wastes for disposal, including GCR wastes. This paper will describe the nature and characteristics of GCR decommissioning wastes which are intended for disposal in a UK repository. The Nirex Waste Package Specifications and the key technical issues, which have been identified when considering GCR decommissioning waste against the performance requirements within the specifications, are discussed. (author)

Repository seal materials performance for a SALT Repository Project 5-year code/model development plan: Draft

International Nuclear Information System (INIS)

1987-06-01

This document describes an integrated laboratory testing and model development effort for the seal system for a high-level nuclear waste repository in salt. The testing and modeling efforts are designed to determine seal material response in the repository environment, to provide models of seal system components for performance assessment, and to assist in the development of seal system designs. A code/model development and performance analysis program will be performed to predict the short- and long-term response of seal materials and seal components. The results from these analyses will be used to support the material testing activities on this contract and to support performance assessment activities that are conducted in other parts of the Salt Repository Project (SRP). 48 refs., 15 figs., 4 tabs

Review. Deep repository for spent nuclear fuel SR 97 - Post-closure safety

International Nuclear Information System (INIS)

Stephansson, Ove

2000-01-01

SKB states that the chosen scenarios provide good coverage of future evolutionary pathways for the deep repository. This is not the case. SKB has not made full use of the established interaction matrices and the new method of THMC diagrams to generate the relevant and important scenarios and to construct the important pathways of variables and processes, either in the established interaction matrices and the presented THMC diagrams. Hence, SKB is demonstrating in SR 97 that they lack a well thought through, sound and solid method to select and evaluate scenarios for the purpose of demonstrating the safety of a deep repository for spent nuclear fuel. The evolution of the system is presented for the components of the repository system (fuel, canister, buffer/backfill, geosphere) and the effects of four different scenarios, but time only enters into the system for discrete events or processes, e.g. description of the relative radiotoxicity and heat decay of the fuel, temperature distribution, iron exchange process, pH in buffer, redox capacity and radionuclear release at the three sites. There is a lack of method and way of describing the evolution of the complete repository system, including the major scenarios, as a function of time. It is essential that SKB is able to: - consider the full range of potential scenarios, - grade the scenarios according to their significance for repository design and performance and safety assessment, - consider whether simple engineering actions could be taken to inhibit the development of adverse scenarios. This cannot be done with the system presented in SR 97, and so SKB do not have a full predictive capability - which is required for the engineering design of such an important and costly structure as a repository. Geoscientific investigation material for three selected sites are presented by SKB in the technical report dealing with waste, repository design and sites. Here a general overview is missing of the geological and rock

The impact of an ED-only full-capacity protocol.

Science.gov (United States)

Watase, Taketo; Fu, Rongwei; Foster, Denise; Langley, Denise; Handel, Daniel A

2012-10-01

The objective of this study was to assess the impact of an emergency department (ED)-only full-capacity protocol and diversion, controlling for patient volumes and other potential confounding factors. This was a preintervention and postintervention cohort study using data 12 months before and 12 months after the implementation of the protocol. During the implementation period, attending physicians and charge nurses were educated with clear and simple figures on the criteria for the initiation of the new protocol. A multiple logistic regression model was used to compare ambulance diversion between the 2 periods. The proportion of days when the ED went on diversion at least once during a 24-hour period was 60.4% during the preimplementation period and 20% in the postimplementation periods (P model, the use of the new protocol was significantly associated with decreased odds of diversion rate in the postimplementation period (odds ratio, 0.32; 95% confidence interval, 0.21-0.48). Our predivert/full-capacity protocol is a simple and generalizable strategy that can be implemented within the boundaries of the ED and is significantly associated with a decreased diversion rate. Copyright © 2012 Elsevier Inc. All rights reserved.

Natural analogues, paradigm for manmade repositories for radioactive wastes

International Nuclear Information System (INIS)

Pavelescu, M.; Pavelescu, A.

2004-01-01

Natural analogues are given by nature. They show the results of natural processes which have lasted thousands or millions of years. They provide an excellent example of what could happen in an underground site, offering in the same time the opportunity to test by observation and measurement, many of the geochemical processes that are expected to influence in a realistic and appropriate way, the predicted reliability of the radioactive waste repository over long periods of geological time. The natural analogue studies attempt to understand the multiprocessing complexity of the natural system, which contrasts with the limitations of the laboratory experiments and bring arguments to overcome the difficult time scale issue. By this the natural analogues are a useful paradigm for manmade repository for radioactive wastes. The paper discusses the implicit link in the public mind between natural analogues and manmade waste repository with an accent of the positive impact on public acceptance. It is also discussed the decisive qualities of the natural analogues concerning providing valid long term data and increasing the confidence of the public for manmade repositories. The debate is conducting in terms of sustainable development, having at base high-level principles in order to protect humans and their environment, both now and in the future, from potential hazards arising from such wastes. Safe radwaste management involves the application of technology and resources in a regulated manner so that the public, workers and the environment are protected in accordance with the accepted national and international standards. There are at least seven high-level principles which are mentioned in the paper. It is presented the general concept of the deep geological repository, very important for an acceptable solution for the management of nuclear waste, what is a prerequisite for a renewal of nuclear power. Further are introduced natural and archaeological (manufactured) analogue

Gas generation and release from the VLJ repository

International Nuclear Information System (INIS)

Vieno, T.; Valkiainen, M.

1992-01-01

The VLJ repository is an underground disposal facility located at the Olkiluoto nuclear power plant site on the west coast of Finland. The repository will house low (LLW) and intermediate level radioactive wastes (MLW) from the TVO I and TVO II BWR's and the spent fuel interim store at Olkiluoto. The disposal rooms have been excavated at a depth of 60... 100 meters in the crystalline bedrock. They consist of two rock silos - one for the LLW and the other for MLW. Low level waste is usually packed in steel drums and steel boxes. Medium level wastes consists of bituminized resins in steel drums. Wastes packages are emplaced in concrete boxes before transportation into the repository. Low level wastes are emplaced in the shotcreted rock silo where no backfilling will used. For medium level wastes, a separate silo of reinforced concrete has been constructed inside the rock silo. No backfilling will be used inside the concrete silo and an opening will be made in the lid of the concrete silo for gas release. The microbial degradation of low level wastes is the principle gas generation process in the repository. The gas transport though the bedrock covering the repository is evaluated with the help of ground water flow study. It is recommended that the shotcrete lining on the ceiling of the repository cavern is partly removed before the final sealing of the repository. Provided that dissipation of gases from the disposal cavern into the rock can been assured, the overall effects of gas generation on the long-term safety of the repository are insignificant. 10 refs., 6 figs

Post-closure radiation dose assessment for Yucca Mountain repository

International Nuclear Information System (INIS)

Jia Mingyan; Zhang Xiabin; Yang Chuncai

2006-01-01

A brief introduction of post-closure long-term radiation safety assessment results was represented for the yucca mountain high-level waste geographic disposal repository. In 1 million years after repository closure, for the higher temperature repository operating mode, the peak annual dose would be 150 millirem (120 millirem under the lower-temperature operating mode) to a reasonably maximally exposed individual approximately 18 kilometers (11 miles) from the repository. The analysis of a drilling intrusion event occurring at 30,000 years indicated a peak of the mean annual dose to the reasonably maximally exposed individual approximately 18 kilometers (11 miles) downstream of the repository would be 0.002 millirem. The analysis of an igneous activity scenario, including a volcanic eruption event and igneous intrusion event indicated a peak of the mean annual dose to the reasonably maximally exposed individual approximately 18 kilometers downstream of the repository would be 0.1 millirem. (authors)

Design of repository sealing systems - 1981

International Nuclear Information System (INIS)

Ellison, R.D.; Shukla, D.K.; Kelsall, P.C.; D'Appolonia Consulting Engineers, Albuquerque, NM)

1982-01-01

Isolating nuclear waste in geologic repositories will require the sealing of penetrations such as access shafts and tunnels, disposal rooms, and exploration boreholes. This paper discusses seal designs developed for a repository in bedded salt referenced to the stratigraphy of southeastern New Mexico. Designs are based on a multiple component concept whereby individual components are designed for a specific function and location. For a repository in salt the major function of the seals is to exclude groundwater inflow. Two main types of component are included for this purpose: (1) bulk-heads are dense concrete structures keyed into the walls of the penetration and are intended to reduce flow at the interface between the seal and the salt; (2) backfills are granular materials compacted in place in the penetration. In the repository the major backfill material is crushed salt, which is expected to consolidate and recrystallize as the rooms close in response to salt creep. Densely compacted clays will be used as backfill in the shafts closer to potential sources of water inflow. 22 references, 10 figures, 1 table

The socioeconomic impacts of high-level nuclear waste facility siting

International Nuclear Information System (INIS)

Murdock, S.H.; Leistritz, F.L.; Hamm, R.R.

1987-01-01

High-level nuclear waste repositories will be located in sparsely settled rural areas in the U.S. These projects will significantly effect the economic, demographic, public service, fiscal, and social (the socioeconomic) dimensions of those rural areas. This paper examines some of the potential socioeconomic impacts and the characteristics of mitigation programs necessary, if these impacts are to be addressed. Both standard impacts, those resulting from the fact that--like many other large-scale developments--repositories will involve a substantial number of new workers and residents (relative to the size of existing communities) and special impacts, those resulting from the fact that repositories store radioactive materials, are examined

Creation of Data Repositories to Advance Nursing Science.

Science.gov (United States)

Perazzo, Joseph; Rodriguez, Margaret; Currie, Jackson; Salata, Robert; Webel, Allison R

2017-12-01

Data repositories are a strategy in line with precision medicine and big data initiatives, and are an efficient way to maximize data utility and form collaborative research relationships. Nurse researchers are uniquely positioned to make a valuable contribution using this strategy. The purpose of this article is to present a review of the benefits and challenges associated with developing data repositories, and to describe the process we used to develop and maintain a data repository in HIV research. Systematic planning, data collection, synthesis, and data sharing have enabled us to conduct robust cross-sectional and longitudinal analyses with more than 200 people living with HIV. Our repository building has also led to collaboration and training, both in and out of our organization. We present a pragmatic and affordable way that nurse scientists can build and maintain a data repository, helping us continue to make to our understanding of health phenomena.

Reducing Psychological Resistance to Digital Repositories

Directory of Open Access Journals (Sweden)

Brian Quinn

2010-06-01

Full Text Available The potential value of digital repositories is dependent on the cooperation of scholars to deposit their work. Although many researchers have been resistant to submitting their work, the literature on digital repositories contains very little research on the psychology of resistance. This article looks at the psychological literature on resistance and explores what its implications might be for reducing the resistance of scholars to submitting their work to digital repositories. Psychologists have devised many potentially useful strategies for reducing resistance that might be used to address the problem; this article examines these strategies and how they might be applied.

Augmenting interoperability across repositories architectural ideas

CERN Multimedia

CERN. Geneva

2005-01-01

The aDORe digital repository architecture designed and implemented by the Los Alamos Research Library is fully standards-based and highly modular, with the various components of the architecture interacting in a protocol-driven manner. Although aDORe was designed for use in the context of the Los Alamos Library, its modular and standards-based design has led to interesting insights regarding possible new levels of interoperability in a federation of heterogeneous repositories. The presentation will discuss these insights, and will illustrate that attractive federations of repositories can be built by introducing rather basic interoperability requirements. The presentation will also show that, once these requirements are met, a powerful service framework that overlays the federation can emerge.

Radioactive waste repository of Cesium of Abadia de Goias. Construction and design; Repositorio de rejeitos radioativos de cesio - Abadia de Goias. Concepcao e projeto

Energy Technology Data Exchange (ETDEWEB)

Tranjan Filho, Alfredo [Comissao Nacional de Energia Nuclear (CNEN), Rio de Janeiro, RJ (Brazil); Alves, Antonio Sergio de Martin; Santos, Cicero Durval Pacifici dos; Passos, Erivaldo Mario dos; Coutinho, Fernando Paulo Millen [NUCLEN Engenharia e Servicos S.A., Rio de Janeiro, RJ (Brazil)

1997-12-31

The main criteria, the methodology, the solutions and parameters that were utilized in the design of the Intermediate and Low Level Radioactive Waste Repository of Abadia de Goias are shortly described. The various design steps are analysed from the preparation of the Safety Analysis Report to the detailing engineering tasks. The safety analysis for the constructed repository had the goal of verifying the magnitude of radioecological impacts corresponding to idealized activity release scenarios, allowing also the possible effects of human intrusion in the repository. These safety studies are intrinsically connected to computer calculations envisaged to simulate the long term performance of the repository. (author) 18 refs., 7 figs., 7 tabs.

Repository-analog experiments of nuclear waste leaching and migration

International Nuclear Information System (INIS)

Seitz, M.G.

1982-01-01

The potential for radionuclide migration from a breached nuclear-waste repository depends on the leaching and subsequent interaction of the leached radionuclides with materials in the groundwater flow path. An attempt is made to consider all interactions using experiments that integrate repository materials. Results of a repository-analog experiment using borosilicate glass, fissured granite, and flowing water suggest: (1) plutonium was immobile possibly because of its low solubility; (2) caesium migrated down slowly because of sorption; and (3) neptunium remained oxidized even in water of low oxidation potential. By summing the effects of all interactions, not just sorption, the repository-analog experiment produced radionuclide migration that could be expected from a breached repository. (author)

Business models for digital repositories

CERN Document Server

CERN. Geneva; Bjørnshauge, Lars

2007-01-01

Those setting up, or planning to set up, a digital repository may be interested to know more about what has gone before them. What is involved, what is the cost, how many people are needed, how have others made the case to their institution, and how do you get anything into it once it is built? I have recently undertaken a study of European repository business models for the DRIVER project and will present an overview of the findings.

Repository exploration

International Nuclear Information System (INIS)

Pentz, D.L.

1984-01-01

This paper discusses exploration objectives and requirements for a nuclear repository in the U.S.A. The importance of designing the exploration program to meet the system performance objectives is emphasized and some examples of the extent of exploration required before the License Application for Construction Authorization is granted are also discussed

Learning frameworks as an alternative to repositories

DEFF Research Database (Denmark)

Dalsgaard, Christian

2005-01-01

This paper presents the concept of ‘learning frameworks’. The purpose of the paper is to discuss and question collections of digital learning objects in large repositories and to argue for large learning frameworks which organise a number of thematically related digital learning materials. Whereas...... a learning object repository contains all kinds of materials, a learning framework consists of an organisation of materials related to a common theme. Further, a repository consists of single, self-contained objects, whereas a learning framework is an open-ended environment which presents a number...

Kincardine deep geologic repository proposal and the public

International Nuclear Information System (INIS)

Squire, T.

2005-01-01

'Full text:' In 2002, the Municipality of Kincardine and OPG signed a Memorandum of Understanding (MOU) regarding the long-term management of low and intermediate level radioactive wastes. The purpose of the MOU was for OPG, in consultation with Kincardine, to develop a plan for the long-term management of low and intermediate level waste at OPG's Western Waste Management Facility (WWMF) located on the Bruce site. An independent assessment, which included geotechnical feasibility and safety analyses, a community attitude survey and interviews with local residents, businesses and tourists, and economic modeling to determine the potential benefits and impacts, was completed in February 2004. Ultimately, Kincardine Council endorsed a resolution (Kincardine Council no. 2004-232) to: 'endorse the opinion of the Nuclear Waste Steering Committee and select the 'Deep Rock Vault' option as the preferred course of study in regards to the management of low and intermediate level radioactive waste'. The surrounding municipalities of Saugeen Shores, Brockton, Arran-Elderslie, and Huron-Kinloss expressed their support for the Deep Geologic Repository proposal. This presentation discusses the history, major steps and public processes surrounding the Kincardine Deep Geologic Repository proposal. (author)

New three-dimensional far-field potential repository thermomechanical calculations

International Nuclear Information System (INIS)

Hardy, M.P.; Bai, M.; Goodrich, R.R.; Lin, M.; Carlisle, S.; Bauer, S.J.

1993-03-01

The thermomechanical effect on the exploratory ramps, drifts, and shafts as a result of high-level nuclear waste disposal is examined using a three-dimensional thermo-elastic model. The repository layout modeled is based on the use of mechanical mining of all excavations with equivalent waste emplacement areal power densities of 57 and 80 kW/acre. Predicted temperatures and stress changes for the north and south access drifts, east main drift, east-west exploratory drift, the north and south Calico Hills access ramps, the Calico Hills north-south exploratory drift, and the optional exploratory studies facility and man and materials shafts are presented for times 10, 35, 50, 100, 300, 500, 1000, 2000, 5000, and 10,000 years after the start of waste emplacement. The study indicates that the east-west exploratory drift at the repository horizon is subject to the highest thermomechanical impact because it is located closest the buried waste canisters. For most exploratory openings, the thermally induced temperatures and stresses tend to reach the maximum magnitudes at approximately 1000 years after waste emplacement

A geotechnical evaluation of potentially acceptable sites for a high-level nuclear waste repository near the Red Lake Indian Reservation

International Nuclear Information System (INIS)

1986-01-01

The scope and work which served as the basis for this report included the following major activities; (1) A review and summary of the screening methodologies utilized by DOE for the selection of proposed nuclear waste repository sites, including a description of the inherent weakness in those methodologies. (2) A description of the geologic and hydrologic features of the rock bodies selected by DOE and an identification of those features which could result in hazardous conditions as a result of the location of a high-level nuclear waste repository. (3) An assessment of potential environmental impacts of the repository and discussion of endanged species in the proposed repository project areas. This report is organized in three major sections in relationship to the scope of work. A list of references is also included at the end of this report. 37 refs., 2 figs

Schwarz methods for discrete elliptic and parabolic problems with an application to nuclear waste repository modellingSchwarz methods for discrete elliptic and parabolic problems with an application to nuclear waste repository modelling

Czech Academy of Sciences Publication Activity Database

Blaheta, Radim; Kohut, Roman; Neytcheva, M.; Starý, Jiří

2007-01-01

Roč. 76, 1-3 (2007), s. 18-27 ISSN 0378-4754 R&D Projects: GA AV ČR 1ET400300415 Institutional research plan: CEZ:AV0Z30860518 Keywords : Overlapping domain decomposition * Schwarz methods * Nuclear waste repository Subject RIV: BA - General Mathematics Impact factor: 0.738, year: 2007

Status of Proposed Repository for Latin-American Spent Fuel

Energy Technology Data Exchange (ETDEWEB)

Ferrada, J.J.

2004-10-04

This report compiles preliminary information that supports the premise that a repository is needed in Latin America and analyzes the nuclear situation (mainly in Argentina and Brazil) in terms of nuclear capabilities, inventories, and regional spent-fuel repositories. The report is based on several sources and summarizes (1) the nuclear capabilities in Latin America and establishes the framework for the need of a permanent repository, (2) the International Atomic Energy Agency (IAEA) approach for a regional spent-fuel repository and describes the support that international institutions are lending to this issue, (3) the current situation in Argentina in order to analyze the Argentinean willingness to find a location for a deep geological repository, and (4) the issues involved in selecting a location for the repository and identifies a potential location. This report then draws conclusions based on an analysis of this information. The focus of this report is mainly on spent fuel and does not elaborate on other radiological waste sources.

Gabbro as a host rock for a nuclear waste repository

International Nuclear Information System (INIS)

Ahlbom, K.; Leijon, B.; Smellie, J.; Liedholm, M.

1992-09-01

As an alternative to granitic rocks, gabbro and other basic rock types have been investigated with respect to their suitability to host a nuclear waste repository. The present report summarizes and examines existing geoscientific knowledge of relevance in assessing the potential merits of gabbro as a repository host rock. Implications in terms of site selection, repository construction and post-closure repository performance are also discussed. The objective of the study is to provide a basis for decisions as regards future consideration of the gabbro alternative. It is found that there are rather few gabbro bodies in Sweden, that are potentially of sufficient size to host a repository. Thus, gabbro offers little latitude as regards site selection. In comparison to siting a repository in granitic rocks, this is a major disadvantage, and it may in fact remove gabbro from further consideration. The potential advantages of gabbro refer to repository performance, and include low hydraulic conductivity and a chemical environment promoting efficient radionuclide retardation. However, results from field investigations show that groundwater flow in gabbro bodies is largely controlled by intersecting heterogeneities, in particular granitic dykes, that are significantly more conductive to water than the gabbro. In the far-field scale significant to repository performance, this may reduce or eliminate the potential effects of favourable hydraulic and chemical characteristics of the gabbro itself. In conclusion, there are apparent difficulties associated with siting a repository in gabbro, due to lack of sufficiently large gabbro bodies. On the basis of the present state of knowledge, no decisive differences can be demonstrated when comparing gabbro with granitic rocks, neither with respects to repository construction, nor as regards repository performance. (au)