Probabilistic risk assessment for new and existing chemicals: Example calculations

NARCIS (Netherlands)

Jager T; Hollander HA den; Janssen GB; Poel P van der; Rikken MGJ; Vermeire TG; ECO; CSR; LAE; CSR

2000-01-01

In the risk assessment methods for new and existing chemicals in the EU, "risk" is characterised by means of the deterministic quotient of exposure and effects (PEC/PNEC or Margin of Safety). From a scientific viewpoint, the uncertainty in the risk quotient should be accounted for explicitly in the

Hydraulic and Condition Assessment of Existing Sewerage Network: A Case Study of an Educational Institute

Science.gov (United States)

Sourabh, Nishant; Timbadiya, P. V.

2018-04-01

The hydraulic simulation of the existing sewerage network provides various information about critical points to assess the deteriorating condition and help in rehabilitation of existing network and future expansion. In the present study, hydraulic and condition assessment of existing network of educational Institute (i.e. Sardar Vallabhbhai National Institute of Technology-Surat, Gujarat, India), having an area of 100 ha and ground levels in range of 5.0-9.0 m above mean sea level, has been carried out using sewage flow simulation for existing and future scenarios analysis using SewerGEMS v8i. The paper describes the features of 4.79 km long sewerage network of institute followed by network model simulation for aforesaid scenarios and recommendations on improvement of the existing network for future use. The total sewer loads for present and future scenarios are 1.67 million litres per day (MLD) and 3.62 MLD, considering the peak factor of 3 on the basis of population. The hydraulic simulation of the existing scenario indicated depth by diameter (d/D) ratio in the range of 0.02-0.48 and velocity range of 0.08-0.53 m/s for existing network for present scenario. For the future scenario, the existing network is needed to be modified and it was found that total of 11 conduits (length: 464.8 m) should be replaced to the next higher diameter available, i.e., 350 mm for utilization of existing network for future scenario. The present study provides the methodology for condition assessment of existing network and its utilization as per guidelines provided by Central Public Health and Environmental Engineering Organization, 2013. The methodology presented in this paper can be used by municipal/public health engineer for the assessment of existing sewerage network for its serviceability and improvement in future.

Seismic evaluation of existing nuclear power plants

International Nuclear Information System (INIS)

2003-01-01

The IAEA nuclear safety standards publications address the site evaluation and the design of new nuclear power plants (NPPs), including seismic hazard assessment and safe seismic design, at the level of the Safety Requirements as well as at the level of dedicated Safety Guides. It rapidly became apparent that the existing nuclear safety standards documents were not adequate for handling specific issues in the seismic evaluation of existing NPPs, and that a dedicated document was necessary. This is the purpose of this Safety Report, which is written in the spirit of the nuclear safety standards and can be regarded as guidance for the interpretation of their intent. Worldwide experience shows that an assessment of the seismic capacity of an existing operating facility can be prompted for the following: (a) Evidence of a greater seismic hazard at the site than expected before, owing to new or additional data and/or to new methods; (b) Regulatory requirements, such as periodic safety reviews, to ensure that the plant has adequate margins for seismic loads; (c) Lack of anti-seismic design or poor anti-seismic design; (d) New technical finding such as vulnerability of some structures (masonry walls) or equipment (relays), other feedback and new experience from real earthquakes. Post-construction evaluation programmes evaluate the current capability of the plant to withstand the seismic concern and identify any necessary upgrades or changes in operating procedures. Seismic qualification is distinguished from seismic evaluation primarily in that seismic qualification is intended to be performed at the design stage of a plant, whereas seismic evaluation is intended to be applied after a plant has been constructed. Although some guidelines do exist for the evaluation of existing NPPs, these are not established at the level of a regulatory guide or its equivalent. Nevertheless, a number of existing NPPs throughout the world have been and are being subjected to review of their

Alternative Aviation Jet Fuel Sustainability Evaluation Report Task 1 : Report Evaluating Existing Sustainability Evaluation Programs

Science.gov (United States)

2011-10-25

This report describes how existing biofuel sustainability evaluation programs meet requirements that are under consideration or are in early phases of adoption and implementation in various US and international contexts. Biofuel sustainability evalua...

Guideline for load and resistance assessment of existing european railway bridges

OpenAIRE

JENSEN, Jens S; CASAS, Joan R; KAROUMI, Raid; PLOS, Mario; CREMONA, Christian; MELBOURNE, Clive

2008-01-01

Many of the European railway bridges are getting close to the end of their service life. At the same time the railway operators demand higher axle loads for freight trains and higher speeds for passenger trains. This requires new and better approaches for assessing both the railway loads and the resistance of railway bridges. The main objective of the "Guideline for Load and Resistance Assessment of Existing European Railway Bridges", developed within EU founded project "Sustainable Bridge...

Use of operational data for the assessment of pre-existing software

International Nuclear Information System (INIS)

Helminen, Atte; Gran, Bjoern Axel; Kristiansen, Monica; Winther, Rune

2004-01-01

To build sufficient confidence on the reliability of the safety systems of nuclear power plants all available sources of information should be used. One important data source is the operational experience collected for the system. The operational experience is particularly applicable for systems of pre-existing software. Even though systems and devices involving pre-existing software are not considered for the functions of highest safety levels of nuclear power plants, they will most probably be introduced to functions of lower safety levels and to none-safety related applications. In the paper we shortly discuss the use of operational experience data for the reliability assessment of pre-existing software in general, and the role of pre-existing software in relation to safety applications. Then we discuss the modelling of operational profiles, the application of expert judgement on operational profiles and the need of a realistic test case. Finally, we discuss the application of operational experience data in Bayesian statistics. (Author)

DOE plutonium disposition study: Analysis of existing ABB-CE Light Water Reactors for the disposition of weapons-grade plutonium. Final report

Energy Technology Data Exchange (ETDEWEB)

1994-06-01

Core reactivity and basic fuel management calculations were conducted on the selected reactors (with emphasis on the System 80 units as being the most desirable choice). Methods used were identical to those reported in the Evolutionary Reactor Report. From these calculations, the basic mission capability was assessed. The selected reactors were studied for modification, such as the addition of control rod nozzles to increase rod worth, and internals and control system modifications that might also be needed. Other system modifications studied included the use of enriched boric acid as soluble poison, and examination of the fuel pool capacities. The basic geometry and mechanical characteristics, materials and fabrication techniques of the fuel assemblies for the selected existing reactors are the same as for System 80+. There will be some differences in plutonium loading, according to the ability of the reactors to load MOX fuel. These differences are not expected to affect licensability or EPA requirements. Therefore, the fuel technology and fuel qualification sections provided in the Evolutionary Reactor Report apply to the existing reactors. An additional factor, in that the existing reactor availability presupposes the use of that reactor for the irradiation of Lead Test Assemblies, is discussed. The reactor operating and facility licenses for the operating plants were reviewed. Licensing strategies for each selected reactor were identified. The spent fuel pool for the selected reactors (Palo Verde) was reviewed for capacity and upgrade requirements. Reactor waste streams were identified and assessed in comparison to uranium fuel operations. Cost assessments and schedules for converting to plutonium disposition were estimated for some of the major modification items. Economic factors (incremental costs associated with using weapons plutonium) were listed and where possible under the scope of work, estimates were made.

Identifying best existing practice for characterization modeling in life cycle impact assessment

DEFF Research Database (Denmark)

Hauschild, Michael Zwicky; Goedkoop, Mark; Guinée, Jeroen

2013-01-01

Purpose: Life cycle impact assessment (LCIA) is a field of active development. The last decade has seen prolific publication of new impact assessment methods covering many different impact categories and providing characterization factors that often deviate from each other for the same substance...... and impact. The LCA standard ISO 14044 is rather general and unspecific in its requirements and offers little help to the LCA practitioner who needs to make a choice. With the aim to identify the best among existing characterization models and provide recommendations to the LCA practitioner, a study...... was performed for the Joint Research Centre of the European Commission (JRC). Methods Existing LCIA methods were collected and their individual characterization models identified at both midpoint and endpoint levels and supplemented with other environmental models of potential use for LCIA. No new developments...

Environmental impact assessment report

Energy Technology Data Exchange (ETDEWEB)

Jung, K. J.; Paik, S. T.; Chung, U. S.; Jung, K. H.; Park, S. K.; Lee, D. G.; Kim, H. R.; Kim, J. K.; Yang, S. H.; Lee, B. J.; Kim, E. H.; Choi, K. S

2000-10-01

This report is the revised Environmental Impact Assessment Report which was made and submitted as one of the license documents for TRIGA Research Reactor D and D Project. The Environmental Impact Assessment Report includes introduction of decommissioning plan, status of reactors and environmental impact of surroundings. Also it was assessed and analyzed on radioactivity for environment, and the plan was established to minimize radioactive material release. Finally environmental monitoring plan was established to confirm whether contaminated or not from radioactivity during decommissioning period. According to the assessment results, the risk of excess exposure will be not on environment and public. The first Environmental Impact Assessment Report was submitted to the government for the license and reviewed by Korea Institute of Nuclear Safety. The first Report was revised including answers for the questions arising from review process.

Determining the in situ concrete strength of existing structures for assessing their structural safety

NARCIS (Netherlands)

Steenbergen, R.D.J.M.; Vervuurt, A.H.J.M.

2012-01-01

EN 13791 applies when assessing the in situ compressive strength of structures and precast concrete components. According to the code itself, it may be adopted when doubt arises about the compressive strength of a concrete. For assessing the structural safety of existing structures, however, the

Optimization and implementation study of plutonium disposition using existing CANDU Reactors. Final report

International Nuclear Information System (INIS)

1996-09-01

Since early 1994, the Department of Energy has been sponsoring studies aimed at evaluating the merits of disposing of surplus US weapons plutonium as Mixed Oxide (MOX) fuel in existing commercial Canadian Pressurized Heavy Water reactors, known as CANDU's. The first report, submitted to DOE in July, 1994 (the 1994 Executive Summary is attached), identified practical and safe options for the consumption of 50 to 100 tons of plutonium in 25 years in some of the existing CANDU reactors operating the Bruce A generating station, on Lake Huron, about 300 km north east of Detroit. By designing the fuel and nuclear performance to operate within existing experience and operating/performance envelope, and by utilizing existing fuel fabrication and transportation facilities and methods, a low cost, low risk method for long term plutonium disposition was developed. In December, 1995, in response to evolving Mission Requirements, the DOE requested a further study of the CANDU option with emphasis on more rapid disposition of the plutonium, and retaining the early start and low risk features of the earlier work. This report is the result of that additional work

Zero-emission vehicle technology assessment. Final report

Energy Technology Data Exchange (ETDEWEB)

Woods, T.

1995-08-01

This is the final report in the Zero-Emission Vehicle (ZEV) Technology Assessment, performed for NYSERDA by Booz-Allen & Hamilton Inc. Booz-Allen wrote the final report, and performed the following tasks as part of the assessment: assembled a database of key ZEV organizations, their products or services, and plans; described the current state of ZEV technologies; identified barriers to widespread ZEV deployment and projected future ZEV technical capabilities; and estimated the cost of ZEVs from 1998 to 2004. Data for the ZEV Technology Assessment were obtained from several sources, including the following: existing ZEV industry publications and Booz-Allen files; major automotive original equipment manufacturers; independent electric vehicle manufacturers; battery developers and manufacturers; infrastructure and component developers and manufacturers; the U.S. Department of Energy, the California Air Resources Board, and other concerned government agencies; trade associations such as the Electric Power Research Institute and the Electric Transportation Coalition; and public and private consortia. These sources were contacted by phone, mail, or in person. Some site visits of manufacturers also were conducted. Where possible, raw data were analyzed by Booz-Allen staff and/or verified by independent sources. Performance data from standardized test cycles were used as much as possible.

Using Pretreatment and Posttreatment Assessments To Enhance and Evaluate Existing Treatment Packages.

Science.gov (United States)

Richman, David M.; Berg, Wendy K.; Wacker, David P.; Stephens, Tracy; Rankin, Barbara; Kilroy, Jennette

1997-01-01

Pretreatment assessment data were used to enhance an existing treatment package to reduce aggression and to increase the positive social interactions of a 9-year-old boy with moderate mental retardation and Hunter's syndrome. Additional reinforcements and punishment components were added and resulted in positive social interactions and suppressed…

Radioactive waste assessment using 'minimum waste generation' scenario - summary report March 1984

International Nuclear Information System (INIS)

Richardson, J.A.; Goodill, D.R.; Tymons, B.J.

1984-11-01

This report describes an assessment of radioactive waste management arisings from a defined nuclear power generation - Scheme 1. Scheme 1 assumes a minimum waste generation scenario with raw waste arisings from 3 main groups; (i) existing and committed commercial reactors; (ii) fuel reprocessing plants, (iii) research, industry and medicine. No decommissioning wastes are considered except for arisings from the final fuel cores from decommissioned reactors. The study uses the SIMULATION2 code which models waste material flows through the system. With a knowledge of the accumulations and average production rates of the raw wastes and their isotopic compositions (or total activities), the rates at which conditioned wastes become available for transportation and disposal are calculated, with specific activity levels. The data bases for the inventory calculations and the assumptions concerning future operation of nuclear facilities were those current in 1983. Both the inventory data and plans for the future of existing nuclear installations have been updated since these calculations were completed. Therefore the results from this assessment do not represent the most up-to-date information available. The report does, however, illustrate the methodology of assessment and indicates the type of information that can be generated. (author)

Requirements for existing buildings

DEFF Research Database (Denmark)

Thomsen, Kirsten Engelund; Wittchen, Kim Bjarne

This report collects energy performance requirements for existing buildings in European member states by June 2012.......This report collects energy performance requirements for existing buildings in European member states by June 2012....

Structural Safety Assessment of Existing Multiarch Tunnel: A Case Study

Directory of Open Access Journals (Sweden)

Jinxing Lai

2017-01-01

Full Text Available Structural health assessment is one of the key activities in maintaining the performance of a tunnel during its service life. Due to the development of modern detection technology, comprehensive structural health assessment system is being established for operating tunnels. To evaluate the actual operational state of Shitigou tunnel, overall detection of the liner crack, tunnel seepage, and liner void was conducted by employing the modern detection technology, such as crack width monitoring technology, concrete strength monitoring technology, and electromagnetic wave nondestructive monitoring technology. Through the statistical analysis of the detection results, the distribution characteristic, development law, and damage grade of structural defects were obtained. Tunnel liner cracks are mainly located on the middle wall; serious water leakage is encountered on the side wall, middle wall, and vault; the strength of foundation and liner structure of left tunnel does not meet the design requirement; the liner voids are mostly located at the tunnel entrance section, especially, on the tunnel vault; and the proportion of influence factors of structural defects should be considered. The research results presented for this study can serve as references for effective design and health assessment of existing multiarch tunnel projects.

Co-existence of Phenylketonuria and Fabry disease on a 3 year-old boy: case report

Directory of Open Access Journals (Sweden)

Bonapace Giuseppe

2010-05-01

Full Text Available Abstract Background The co-existence of two genetically distinct metabolic disorders in the same patient has rarely been reported. Phenylketonuria (PKU is an inborn error of the metabolism resulting from a phenylalanine hydroxylase deficiency. Fabry disease (FD is an X-linked lysosomal storage disorder due to a deficiency of the enzyme alpha-galactosidase A. Case presentation We report a case of a 3 year- old boy affected by classic PKU and FD, both confirmed by molecular data. The FD was suspected at the age of 21 months on the presence of non-specific GI symptoms (severe abdominal pain and periodically appearance of not specific episodes of gastroenteritis apparently non related to PKU. Conclusion This is the first report of co-existence of FD and PKU, two different congenital inborn of metabolism and in consideration of the prevalence of each disease this chance association is a very unusual event. The co-existence of this diseases made very difficult the correct interpretation of clinical symptoms as lack of appetite, severe abdominal pain and non-specific gastroenteritis episodes. Furthermore, this case report helps to define the early clinical phenotype of FD.

Safety assessment of research reactors and preparation of the safety analysis report

International Nuclear Information System (INIS)

1994-01-01

This Safety Guide presents guidelines, approved by international consensus, for the preparation, review and assessment of safety documentation for research reactors such as the Safety Analysis Report. While the Guide is most applicable to research reactors in the design and construction stage, it is also recommended for use during relicensing or reassessment of existing reactors

Assessment of Patient-Reported Outcome Instruments to Assess Chronic Low Back Pain.

Science.gov (United States)

Ramasamy, Abhilasha; Martin, Mona L; Blum, Steven I; Liedgens, Hiltrud; Argoff, Charles; Freynhagen, Rainer; Wallace, Mark; McCarrier, Kelly P; Bushnell, Donald M; Hatley, Noël V; Patrick, Donald L

2017-06-01

 To identify patient-reported outcome (PRO) instruments that assess chronic low back pain (cLBP) symptoms (specifically pain qualities) and/or impacts for potential use in cLBP clinical trials to demonstrate treatment benefit and support labeling claims.  Literature review of existing PRO measures.  Publications detailing existing PRO measures for cLBP were identified, reviewed, and summarized. As recommended by the US Food & Drug Administration (FDA) PRO development guidance, standard measurement characteristics were reviewed, including development history, psychometric properties (validity and reliability), ability to detect change, and interpretation of observed changes.  Thirteen instruments were selected and reviewed: Low Back Pain Bothersomeness Scale, Neuropathic Pain Symptom Inventory, PainDETECT, Pain Quality Assessment Scale Revised, Revised Short Form McGill Pain Questionnaire, Low Back Pain Impact Questionnaire, Oswestry Disability Index, Pain Disability Index, Roland-Morris Disability Questionnaire, Brief Pain Inventory and Brief Pain Inventory Short Form, Musculoskeletal Outcomes Data Evaluation and Management System Spine Module, Orebro Musculoskeletal Pain Questionnaire, and the West Haven-Yale Multidimensional Pain Inventory Interference Scale. The instruments varied in the aspects of pain and/or impacts that they assessed, and none of the instruments fulfilled all criteria for use in clinical trials to support labeling claims based on recommendations outlined in the FDA PRO guidance.  There is an unmet need for a validated PRO instrument to evaluate cLBP-related symptoms and impacts for use in clinical trials. © 2017 American Academy of Pain Medicine. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com

Simplified Assessment of R3 Nominal Assurance Degree to Seismic Action of the Existing Masonry Dwellings

Directory of Open Access Journals (Sweden)

Teodor Broşteanu

2008-01-01

Full Text Available This paper refers to the assessment of the performance level of a building for a given seismic hazard level. Building performance level describes the expected seismic performance given by the computation of R3 Nominal Assurance Degree to Seismic Action of the Existing Masonry Dwellings and Monumental Buildings according to the Romanian Norm P100:1992 [1], modified on 1996 with the chapters 11 and 12, until the Part 3 of P100-1:2006 [2], will be performed for the Assessment and Strengthening Structural Design of the Seismic Vulnerable, Existing Buildings, in the frame of SR EN 1998-1:2004 EC8 [3]. The framing of damages into the potential risk degrees has a social and economic impact. Assessment and retrofitting of the existing buildings have represented a huge engineering challenge as a distinct problem versus a new building design. The performance level of a vulnerable existing building shows us the expected seismic performance level due to the classified damages, the pattern of cracks, the interruption of function, the economic losses and the needed interventions, all in function of the importance class of building on next life span of use. On recommends the computation of R (R3 Nominal Assurance Degree to Seismic Action of the Vulnerable Dwellings for the assessing and strengthening design, in comparison to both norms because of the bearing conventional seismic load computed by [1], will result less than the value which will be computed by the Part 3 of P100-1:2006, i.e. the norm P100:1992 is more severe. In the case of the breakable fracture probability of the existing structural masonry members, one recommends a bigger value of ? – reduction factor unless the given values by [1] for a new structure with a high ductility, especially for the deflections calibration on the same limit state.

Development of a Symptom-Based Patient-Reported Outcome Instrument for Functional Dyspepsia: A Preliminary Conceptual Model and an Evaluation of the Adequacy of Existing Instruments.

Science.gov (United States)

Taylor, Fiona; Reasner, David S; Carson, Robyn T; Deal, Linda S; Foley, Catherine; Iovin, Ramon; Lundy, J Jason; Pompilus, Farrah; Shields, Alan L; Silberg, Debra G

2016-10-01

The aim was to document, from the perspective of the empirical literature, the primary symptoms of functional dyspepsia (FD), evaluate the extent to which existing questionnaires target those symptoms, and, finally, identify any missing evidence that would impact the questionnaires' use in regulated clinical trials to assess treatment efficacy claims intended for product labeling. A literature review was conducted to identify the primary symptoms of FD and existing symptom-based FD patient-reported outcome (PRO) instruments. Following a database search, abstracts were screened and articles were retrieved for review. The primary symptoms of FD were organized into a conceptual model and the PRO instruments were evaluated for conceptual coverage as well as compared against evidentiary requirements presented in the FDA's PRO Guidance for Industry. Fifty-six articles and 16 instruments assessing FD symptoms were reviewed. Concepts listed in the Rome III criteria for FD (n = 7), those assessed by existing FD instruments (n = 34), and symptoms reported by patients in published qualitative research (n = 6) were summarized in the FD conceptual model. Except for vomiting, all of the identified symptoms from the published qualitative research reports were also specified in the Rome III criteria. Only three of the 16 instruments, the Dyspepsia Symptom Severity Index (DSSI), Nepean Dyspepsia Index (NDI), and Short-Form Nepean Dyspepsia Index (SF-NDI), measure all seven FD symptoms defined by the Rome III criteria. Among these three, each utilizes a 2-week recall period and 5-point Likert-type scale, and had evidence of patient involvement in development. Despite their coverage, when these instruments were evaluated in light of regulatory expectations, several issues jeopardized their potential qualification for substantiation of a labeling claim. No existing PRO instruments that measured all seven symptoms adhered to the regulatory principles necessary to support product

The Bristol Radiology Report Assessment Tool (BRRAT): Developing a workplace-based assessment tool for radiology reporting skills

International Nuclear Information System (INIS)

Wallis, A.; Edey, A.; Prothero, D.; McCoubrie, P.

2013-01-01

Aim: To review the development of a workplace-based assessment tool to assess the quality of written radiology reports and assess its reliability, feasibility, and validity. Materials and methods: A comprehensive literature review and rigorous Delphi study enabled the development of the Bristol Radiology Report Assessment Tool (BRRAT), which consists of 19 questions and a global assessment score. Three assessors applied the assessment tool to 240 radiology reports provided by 24 radiology trainees. Results: The reliability coefficient for the 19 questions was 0.79 and the equivalent coefficient for the global assessment scores was 0.67. Generalizability coefficients demonstrate that higher numbers of assessors and assessments are needed to reach acceptable levels of reliability for summative assessments due to assessor subjectivity. Conclusion: The study methodology gives good validity and strong foundation in best-practice. The assessment tool developed for radiology reporting is reliable and most suited to formative assessments

The Bristol Radiology Report Assessment Tool (BRRAT): developing a workplace-based assessment tool for radiology reporting skills.

Science.gov (United States)

Wallis, A; Edey, A; Prothero, D; McCoubrie, P

2013-11-01

To review the development of a workplace-based assessment tool to assess the quality of written radiology reports and assess its reliability, feasibility, and validity. A comprehensive literature review and rigorous Delphi study enabled the development of the Bristol Radiology Report Assessment Tool (BRRAT), which consists of 19 questions and a global assessment score. Three assessors applied the assessment tool to 240 radiology reports provided by 24 radiology trainees. The reliability coefficient for the 19 questions was 0.79 and the equivalent coefficient for the global assessment scores was 0.67. Generalizability coefficients demonstrate that higher numbers of assessors and assessments are needed to reach acceptable levels of reliability for summative assessments due to assessor subjectivity. The study methodology gives good validity and strong foundation in best-practice. The assessment tool developed for radiology reporting is reliable and most suited to formative assessments. Copyright © 2013 The Royal College of Radiologists. Published by Elsevier Ltd. All rights reserved.

ENGINEERING SPECIALTY ASSESSMENT OF TANK WASTE COMPATIBILITY REPORTING

International Nuclear Information System (INIS)

KNIGHT, M.A.

2003-01-01

This Engineering Specialty Assessment was conducted to review the Tank Farm Waste Transfer Compatibility Program to assess whether the program meets the needs of accelerated retrieval and closure and waste feed delivery and to identify areas and methods for streamlining the program. The assessment was conducted in June 2003 and resulted in two findings and thirteen observations. The assessment results indicate that significant opportunities exist for streamlining the program by reducing the number of criteria requiring evaluation from 21 to 11, with only six of the criteria requiring evaluation for the majority of transfers. The assessment identified areas where existing criteria require strengthening to ensure that the risks of undesirable solids precipitation, from either waste mixing or waste transfer, are minimized. The assessment further identified opportunities for using existing engineering tools to simplify the calculations involved with preparation of waste compatibility assessments. The need to ensure that a revision to the waste compatibility program is prepared to align the program criteria with those that will be implemented with the DSA approval was also identified. Finally, the assessment identified that corrective actions are required to implement a tank-by-tank PCB inventory within the Best Basis Inventory and to ensure that sample data from external waste generators is entered into the TWINS database

On the use of NDT Data for Reliability-Based Assessment of Existing Timber Structures

DEFF Research Database (Denmark)

Sousa, Hélder S.; Sørensen, John Dalsgaard; Kirkegaard, Poul Henning

2013-01-01

The objective of this paper is to address the possibilities of using non-destructive testing (NDT) data for updating information and obtaining adequate characterization of the reliability level of existing timber structures and, also, for assessing the evolution in time of performance...... of these structures when exposed to deterioration. By improving the knowledge upon the mechanical properties of timber, better and more substantiated decisions after a reliability safety assessment are aimed at. Bayesian methods are used to update the mechanical properties of timber and reliability assessment......, and information of NDT is also used to calibrate these models. The proposed approach is used for reliability assessment of different structural timber systems. Reliability of the structural system is assessed regarding the failure consequences of individual elements defined as key elements which were determined...

Save Energy Now Assessments Results 2008 Detailed Report

Energy Technology Data Exchange (ETDEWEB)

Wright, Anthony L [ORNL; Martin, Michaela A [ORNL; Nimbalkar, Sachin U [ORNL; Quinn, James [U.S. Department of Energy; Glatt, Ms. Sandy [DOE Industrial Technologies Program; Orthwein, Mr. Bill [U.S. Department of Energy

2010-09-01

In October 2005, U.S. Department of Energy Secretary Bodman launched his Easy Ways to Save Energy campaign with a promise to provide energy assessments to 200 of the largest U.S. manufacturing plants. DOE's Industrial Technologies Program (ITP) responded to the Secretary's campaign with its Save Energy Now initiative, featuring a new and highly cost-effective form of energy savings assessment. The approach for these assessments drew heavily on the existing resources of ITP's technology delivery component. Over the years, ITP Technology Delivery has worked with industry partners to assemble a suite of respected software tools, proven assessment protocols, training curricula, certified energy experts, and strong partnerships for deployment. The Save Energy Now assessments conducted in calendar year 2006 focused on natural gas savings and targeted many of the nation's largest manufacturing plants - those that consume at least 1 TBtu of energy annually. The 2006 Save Energy Now assessments focused primarily on assessments of steam and process heating systems, which account for an estimated 74% of all natural gas use by U.S. manufacturing plants. Because of the success of the Save Energy Now assessments conducted in 2006 and 2007, the program was expanded and enhanced in two major ways in 2008: (1) a new goal was set to perform at least 260 assessments; and (2) the assessment focus was expanded to include pumping, compressed air, and fan systems in addition to steam and process heating. DOE ITP also has developed software tools to assess energy efficiency improvement opportunities in pumping, compressed air, and fan systems. The Save Energy Now assessments integrate a strong training component designed to teach industrial plant personnel how to use DOE's opportunity assessment software tools. This approach has the advantages of promoting strong buy-in of plant personnel for the assessment and its outcomes and preparing them better to

Environmental hazards assessment program. Annual report, July 1, 1994--June 30, 1995

International Nuclear Information System (INIS)

1995-01-01

This report describes activities and reports on progress for the third year of the DOE grant to support the Environmental Hazards Assessment Program (EHAP). It reports progress against grant objectives and the Program Implementation Plan published at the end of the first year of the grant. As the program has evolved, more projects have been funded and many existing projects have become more complex. Thus, to accomplish better the objectives over the years and retain a solid focus on the total mission, we have reorganized the grant effort from three to five majoe elements: Public and professional outreach; Clinical programs; Science programs; Information systems; and, Program management

Environmental hazards assessment program. Annual report, July 1, 1994--June 30, 1995

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-07-31

This report describes activities and reports on progress for the third year of the DOE grant to support the Environmental Hazards Assessment Program (EHAP). It reports progress against grant objectives and the Program Implementation Plan published at the end of the first year of the grant. As the program has evolved, more projects have been funded and many existing projects have become more complex. Thus, to accomplish better the objectives over the years and retain a solid focus on the total mission, we have reorganized the grant effort from three to five majoe elements: Public and professional outreach; Clinical programs; Science programs; Information systems; and, Program management.

Energy Efficiency in the North American Existing Building Stock

Energy Technology Data Exchange (ETDEWEB)

NONE

2007-07-01

This report presents the findings of a new assessment of the techno-economic and policy-related efficiency improvement potential in the North American building stock conducted as part of a wider appraisal of existing buildings in member states of the International Energy Agency. It summarizes results and provides insights into the lessons learned through a broader global review of best practice to improve the energy efficiency of existing buildings. At this time, the report is limited to the USA because of the large size of its buildings market. At a later date, a more complete review may include some details about policies and programs in Canada. If resources are available an additional comprehensive review of Canada and Mexico may be performed in the future.

Use of existing patient-reported outcome (PRO) instruments and their modification: the ISPOR Good Research Practices for Evaluating and Documenting Content Validity for the Use of Existing Instruments and Their Modification PRO Task Force Report.

Science.gov (United States)

Rothman, Margaret; Burke, Laurie; Erickson, Pennifer; Leidy, Nancy Kline; Patrick, Donald L; Petrie, Charles D

2009-01-01

Patient-reported outcome (PRO) instruments are used to evaluate the effect of medical products on how patients feel or function. This article presents the results of an ISPOR task force convened to address good clinical research practices for the use of existing or modified PRO instruments to support medical product labeling claims. The focus of the article is on content validity, with specific reference to existing or modified PRO instruments, because of the importance of content validity in selecting or modifying an existing PRO instrument and the lack of consensus in the research community regarding best practices for establishing and documenting this measurement property. Topics addressed in the article include: definition and general description of content validity; PRO concept identification as the important first step in establishing content validity; instrument identification and the initial review process; key issues in qualitative methodology; and potential threats to content validity, with three case examples used to illustrate types of threats and how they might be resolved. A table of steps used to identify and evaluate an existing PRO instrument is provided, and figures are used to illustrate the meaning of content validity in relationship to instrument development and evaluation. RESULTS & RECOMMENDATIONS: Four important threats to content validity are identified: unclear conceptual match between the PRO instrument and the intended claim, lack of direct patient input into PRO item content from the target population in which the claim is desired, no evidence that the most relevant and important item content is contained in the instrument, and lack of documentation to support modifications to the PRO instrument. In some cases, careful review of the threats to content validity in a specific application may be reduced through additional well documented qualitative studies that specifically address the issue of concern. Published evidence of the content

Review of international geothermal activities and assessment of US industry opportunities: Summary report

Energy Technology Data Exchange (ETDEWEB)

1987-08-01

This report summarizes a study initiated to review and assess international developments in the geothermal energy field and to define business opportunities for the US geothermal industry. The report establishes data bases on the status of worldwide geothermal development and the competitiveness of US industry. Other factors identified include existing legislation, tax incentives, and government institutions or agencies and private sector organizations that promote geothermal exports. Based on the initial search of 177 countries and geographic entities, 71 countries and areas were selected as the most likely targets for the expansion of the geothermal industry internationally. The study then determined to what extent their geothermal resource had been developed, what countries had aided or participated in this development, and what plans existed for future development. Data on the energy, economic, and financial situations were gathered.

Hanford Site background: Evaluation of existing soil radionuclide data

International Nuclear Information System (INIS)

1995-07-01

This report is an evaluation of the existing data on radiological background for soils in the vicinity of the Hanford Site. The primary purpose of this report is to assess the adequacy of the existing data to serve as a radiological background baseline for use in environmental restoration and remediation activities at the Hanford Site. The soil background data compiled and evaluated in this report were collected by the Pacific Northwest Laboratory (PNL) and Washington State Department of Health (DOH) radiation surveillance programs in southeastern Washington. These two programs provide the largest well-documented, quantitative data sets available to evaluate background conditions at the Hanford Site. The data quality objectives (DQOs) considered in this evaluation include the amount of data, number of sampling localities, spatial coverage, number and types of radionuclides reported, frequency of reporting, documentation and traceability of sampling and laboratory methods used, and comparability between sets of data. Although other data on soil radionuclide abundances around the Hanford Site exist, they are generally limited in scope and lack the DQOs necessary for consideration with the PNL and DOH data sets. Collectively, these two sources provide data on the activities of 25 radionuclides and four other parameters (gross alpha, gross beta, total uranium, and total thorium). These measurements were made on samples from the upper 2.5 cm of soil at over 70 localities within the region

Measuring the quality of patient-centered care: why patient-reported measures are critical to reliable assessment

Directory of Open Access Journals (Sweden)

Tzelepis F

2015-06-01

Full Text Available Flora Tzelepis, Robert W Sanson-Fisher, Alison C Zucca, Elizabeth A FradgleyPriority Research Centre for Health Behaviour, University of Newcastle and Hunter Medical Research Institute, Newcastle, NSW, AustraliaPurpose: The Institute of Medicine (IOM identified patient-centeredness as crucial to quality health care. The IOM endorsed six patient-centeredness dimensions that stipulated that care must be: respectful to patients’ values, preferences, and expressed needs; coordinated and integrated; provide information, communication, and education; ensure physical comfort; provide emotional support; and involve family and friends. Patient-reported measures examine the patient’s perspective and are essential to the accurate assessment of patient-centered care. This article’s objectives are to: 1 use the six IOM-endorsed patient-centeredness dimensions as a framework to outline why patient-reported measures are crucial to the reliable measurement of patient-centered care; and 2 to identify existing patient-reported measures that assess each patient-centered care dimension.Methods: For each IOM-endorsed patient-centeredness dimension, the published literature was searched to highlight the essential role of patients in assessing patient-centered care and informing quality improvement efforts. Existing literature was also searched to identify examples of patient-reported measures that assess each patient-centeredness dimension.Conclusion: Patient-reported measures are arguably the best way to measure patient-centeredness. For instance, patients are best positioned to determine whether care aligns with patient values, preferences, and needs and the Measure of Patient Preferences is an example of a patient-reported measure that does so. Furthermore, only the patient knows whether they received the level of information desired, and if information was understood and can be recalled. Patient-reported measures that examine information provision include

Assessment of wind turbine seismic risk : existing literature and simple study of tower moment demand.

Energy Technology Data Exchange (ETDEWEB)

Prowell, Ian (University of California, San Diego, CA); Veers, Paul S.

2009-03-01

Various sources of risk exist for all civil structures, one of which is seismic risk. As structures change in scale, the magnitude of seismic risk changes relative to risk from other sources. This paper presents an introduction to seismic hazard as applied to wind turbine structures. The existing design methods and research regarding seismic risk for wind turbines is then summarized. Finally a preliminary assessment is made based on current guidelines to understand how tower moment demand scales as rated power increases. Potential areas of uncertainty in the application of the current guidelines are summarized.

Summary report of already existing guidance on the implementation of External Hazards in extended Level 1 PSA

International Nuclear Information System (INIS)

Klug, J.; Kumar, M.; Prochaska, J.; Brac, P.; Vasseur, D.; Brinkman, H.; Kahia, S.; Nitoi, Mirela; Apostol, M.; Georgescu, G.; Volkanovski, Andrija; Mustoe, J.; Alzbutas, R.; La Rovere, S.

2015-08-01

The report provides a summary of already existing guidance on the implementation of external hazards in extended level 1 PSA. It summarized the lessons learnt from existing standards, existing gaps and possibility for future development within the work-package WP22 'How to introduce hazards in L1 PSA and all possibilities of events combinations'. The report is focused on the four following areas, for several hazards: 1) Impact on the SSCs modelled in L1 PSA event trees; 2) Impact on Human Reliability Assessment modelling in L1 PSA; 3) Site impact modelling in L1 PSA event trees; 4) Link between external initiating events of PSA and NPP design basis conditions. During the review of existing guidance, it appeared that many of the references form a suitable basis to introduce external hazards in L1 PSA including event combination. Available guidelines provide usable recommendations to evaluate failure probabilities of SSCs depending on the influence of single hazard or events combination. The most detailed guidelines are devoted to the seismic events and fires. Even if these guidelines deal only with single event impact, they can be also used for combined events purpose to evaluate particular effects induced by analyzed external hazards. Guidelines provide general systematic framework how to determine the scope of SSCs for extended PSA and failure modes (develop an extended list of components). In general available guidelines provide detailed framework for analysis of seismic event. The other external hazards are not always covered so deeply. This is probably caused by specific site nature of these hazards like external floods, fires etc. In case of HRA, more detailed information and HRA models are available for seismic events or fire events. For the other external hazards, the literature with regard to HRA is not well developed. The PSA for external hazards should take account the potential for human response to be affected by the external event. More realistic Human

Prevalence of HIV among MSM in Europe: comparison of self-reported diagnoses from a large scale internet survey and existing national estimates

Directory of Open Access Journals (Sweden)

Marcus Ulrich

2012-11-01

Full Text Available Abstract Background Country level comparisons of HIV prevalence among men having sex with men (MSM is challenging for a variety of reasons, including differences in the definition and measurement of the denominator group, recruitment strategies and the HIV detection methods. To assess their comparability, self-reported data on HIV diagnoses in a 2010 pan-European MSM internet survey (EMIS were compared with pre-existing estimates of HIV prevalence in MSM from a variety of European countries. Methods The first pan-European survey of MSM recruited more than 180,000 men from 38 countries across Europe and included questions on the year and result of last HIV test. HIV prevalence as measured in EMIS was compared with national estimates of HIV prevalence based on studies using biological measurements or modelling approaches to explore the degree of agreement between different methods. Existing estimates were taken from Dublin Declaration Monitoring Reports or UNAIDS country fact sheets, and were verified by contacting the nominated contact points for HIV surveillance in EU/EEA countries. Results The EMIS self-reported measurements of HIV prevalence were strongly correlated with existing estimates based on biological measurement and modelling studies using surveillance data (R2=0.70 resp. 0.72. In most countries HIV positive MSM appeared disproportionately likely to participate in EMIS, and prevalences as measured in EMIS are approximately twice the estimates based on existing estimates. Conclusions Comparison of diagnosed HIV prevalence as measured in EMIS with pre-existing estimates based on biological measurements using varied sampling frames (e.g. Respondent Driven Sampling, Time and Location Sampling demonstrates a high correlation and suggests similar selection biases from both types of studies. For comparison with modelled estimates the self-selection bias of the Internet survey with increased participation of men diagnosed with HIV has to be

HET/JUPITER project assessment report

International Nuclear Information System (INIS)

Baxter, B.J.; Harrington, F.E.; Kaiser, G.G.; Wolf, J.

1979-05-01

This report is an assessment of the United States' Hot Engineering Test (HET) and the Federal Republic of Germany's Juelich Pilot Plant Thorium Element Reprocessing (JUPITER) Projects. The assessment was conducted with a view to developing mutually supportive roles in the achievement of hot engineering test objectives. Conclusions of the assessment are positive and identify several technical areas with potential for US/FRG cooperation. Recommendations presented in this report support a cost-effective US/FRG program to jointly develop high temperature gas-cooled reactor fuel recycle technology. (orig.) [de

Measuring the Success of Changes to Existing Business Intelligence Solutions to Improve Business Intelligence Reporting

OpenAIRE

Dedić, Nedim; Stanier, Clare

2016-01-01

Evaluating the success of changes to an existing Business Intelligence (BI) environment means that there is a need to compare the level of user satisfaction with the original and amended versions of the application. The focus of this paper is on producing an evaluation tool, which can be used to measure the success of changes to existing BI solutions to support improved BI reporting. The paper identifies the users involved in the BI process and investigates what is meant by satisfaction in th...

Developing a safety report for an existing conversion facility

International Nuclear Information System (INIS)

Carisse, Hess

2013-01-01

A review of the process used to meet the regulatory requirements for a Safety Report at an existing conversion facility is described. This paper will cover the establishment of the regulatory criteria, selection of appropriate methodologies, identification of events and modeling of credible events. Once established there is on-going maintenance to deal with design changes and the need for periodic reviews will also be discussed. Challenges in dealing with the various phases, including incorporation of historical licensing documents, and lessons learned are presented. Of specific interest is the failure of the selected methodology to deal with infrastructure issues. One aspect of lessons learned that will be explored is the lack of an available mechanism for sharing information with similar fuel cycle facilities which is compounded by the fact that there are a small number of fuel cycle facilities compared to nuclear power plants. Possible approaches to dealing with this issue are also discussed. (authors)

Assessing seismic adequacy of existing nuclear power plant structures

International Nuclear Information System (INIS)

Belyaev, V.; Vinogradov, V.; Privalov, S.; Shishenin, V.

2003-01-01

Nowadays Russia's specialists perform a huge amount of works to revaluate the NPP safety. These works are certain to include refinement of NPP safety assessment under the effects of specific dynamic loads, earthquake effects included. It should be noted, that a number of Russian NPPs now in operation had been designed either with no account of these loads, or under the requirements which are underestimated as compared with the modern requirements on the external load composition and rate. Revaluation of NPP seismic safety is based on the results of the works taken under orderly sequence on assessment of (1) seismic input and ground effects; (2) structure response and state; (3) equipment and pipelines response and state. The paper considers the methods of NPP structures response and state assessment. Therewith we assume that ground motion predicted behavior at the construction basement has been preset for the SSE and OBE conditions and the effects of soil-structure interaction, including the situation of possible soft soil liquefaction. Necessity to determine both the reaction of a construction and its state as a whole as well as its elements reaction, to evaluate their bearing capacity and destruction zones formation makes it necessary to make up a detailed structural model, which is usually a finite element one. Since seismic revaluation is to be performed for the existing structures, characteristics of which can substantially differ from the design ones, revealing the actual state of this structures becomes critical. If the real values of physical and mechanical properties of the structure materials, connections of elements etc. are used as initial data in a structural model this permits to increase the design assessment credibility and reliability substantially. The paper analyzes the results of determining these initial assessments while inspecting several Russian NPPs on the basis of a 'combined' method. This method is realized at two consecutive stages. The

Joint Egypt/United States report on Egypt/United States cooperative energy assessment. Volume 2 of 5 Vols. Annex 1

Energy Technology Data Exchange (ETDEWEB)

1979-04-01

Detailed summaries are presented of Egypt's indigenous energy resources from the U.S. Geological Survey assessments; preliminary information collected early in 1977 from files, reports, and publications existing in the U.S.; and data gathered during one-month assessment program in March--April 1978. Detailed reports are given on oil and gas, coal and oil shale, uranium and thorium, geothermal energy, water resources, and energy-related minerals/commodities. An assessment of cement-making materials, iron ore, manganese, aluminium, barite, bentonite, copper, chromium, nickel, titanium, and miscellaneous metals used in steel making is presented.

Assessments of conditioned radioactive waste arisings from existing and committed nuclear installations and assuming a moderate growth in nuclear electricity generation - June 1985

International Nuclear Information System (INIS)

Fairclough, M.P.; Goodill, D.R.; Tymons, B.J.

1985-03-01

This report describes an assessment of conditioned radioactive waste arisings from existing and committed nuclear installations, DOE Revised Scheme 1, and from an assumed nuclear power generation scenario, DOE Revised Scheme 3, representing a moderate growth in nuclear generation. Radioactive waste arise from 3 main groups of installations and activities: i. existing and committed commercial reactors; ii. fuel reprocessing plants, iii. research, industrial and medical activities. Stage 2 decommissioning wastes are considered together with WAGR decommissioning and the 1983 Sea Dump Consignment. The study uses the SIMULATION 2 code which models waste material flows through a system of waste treatment and packaging to disposal. With a knowledge of the accumulations and average production rates of untreated wastes and their isotopic compositions (or total activities), the rates at which conditioned wastes become available for transportation and disposal are calculated, with specific activity levels. The data for the inventory calculations have previously been documented. Some recent revisions and assumptions concerning future operation of nuclear facilities are presented in this report. (author)

System Aspects of Black Liquor Gasification. A review of existing reports

Energy Technology Data Exchange (ETDEWEB)

Berntsson, Thore [Chalmers Univ. of Technology, Goeteborg (Sweden)

2008-12-15

Black liquor gasification (BLG) is one of the high-prioritized RandD areas in Sweden. Research work is going on in the national program BLG-Programme. The main aims with the present study are to: - Identify larger projects dealing with energy oriented system aspects of BLG - Make a synthesis on system aspects results in these projects - Identify need for further work, e.g. as a part of a second period of the BLG Programme. No new work or calculations have been performed, the aim has been only to compile and draw conclusions from existing information. The focus has been on system studies. Most of the research on BLG has been technically, chemically and component oriented. These areas are not included in this report. In Chapter 2 basics for BLG are presented and in Chapter 3 important system aspects of this technology are discussed. Future opportunities for energy savings in mills are crucial for a BLG system, both technically and economically. Therefore present knowledge for such opportunities is presented in Chapter 4. In section 1.4 the report/projects included in this report are introduced and in Chapter 5-13 Summaries, especially on system aspects, of these reports are given. In order to keep the report at a reasonable size only major projects dealing with system aspects during the last 10 year period have been included. In Chapter 14 a synthesis of system aspects dealt with in the different reports is presented and in Chapter 15 suggestions for further work are given. In Chapter 16 references are given and finally in the Attachment a brief overview of different BLG technologies is presented

Contour plot assessment of existing meta-analyses confirms robust association of statin use and acute kidney injury risk.

Science.gov (United States)

Chevance, Aurélie; Schuster, Tibor; Steele, Russell; Ternès, Nils; Platt, Robert W

2015-10-01

Robustness of an existing meta-analysis can justify decisions on whether to conduct an additional study addressing the same research question. We illustrate the graphical assessment of the potential impact of an additional study on an existing meta-analysis using published data on statin use and the risk of acute kidney injury. A previously proposed graphical augmentation approach is used to assess the sensitivity of the current test and heterogeneity statistics extracted from existing meta-analysis data. In addition, we extended the graphical augmentation approach to assess potential changes in the pooled effect estimate after updating a current meta-analysis and applied the three graphical contour definitions to data from meta-analyses on statin use and acute kidney injury risk. In the considered example data, the pooled effect estimates and heterogeneity indices demonstrated to be considerably robust to the addition of a future study. Supportingly, for some previously inconclusive meta-analyses, a study update might yield statistically significant kidney injury risk increase associated with higher statin exposure. The illustrated contour approach should become a standard tool for the assessment of the robustness of meta-analyses. It can guide decisions on whether to conduct additional studies addressing a relevant research question. Copyright © 2015 Elsevier Inc. All rights reserved.

Cone beam computerized tomography of face. Technological assessment report

International Nuclear Information System (INIS)

Saint-Pierre, Francoise; Fanelli, Gaelle; Mosnegutu, Lavinia; Devaux, Frederique

2009-12-01

Cone beam computerized tomography is an imagery technique notably used for the maxillofacial complex or a complete or limited exploration of maxillo-mandibular and dento-alveolar structures. Typically, this technique is implemented with devices which are different from scanners in various respects (performance of several linear cuts, use of an open cone beam). Based on a literature survey, this document reports an assessment which aimed at determining technical and dosimetric performances of the device, potential benefits in terms of diagnosis and therapy with respect to existing imagery techniques, specifications and role of this technique in odonto-stomatology, maxillofacial surgery, and even in ENT, and operation conditions and training to perform this act

Patient-Reported Outcome and Observer-Reported Outcome Assessment in Rare Disease Clinical Trials: An ISPOR COA Emerging Good Practices Task Force Report.

Science.gov (United States)

Benjamin, Katy; Vernon, Margaret K; Patrick, Donald L; Perfetto, Eleanor; Nestler-Parr, Sandra; Burke, Laurie

Rare diseases (RDs) affect a small number of people within a population. About 5000 to 8000 distinct RDs have been identified, with an estimated 6% to 8% of people worldwide suffering from an RD. Approximately 75% of RDs affect children. Frequently, these conditions are heterogeneous; many are progressive. Regulatory incentives have increased orphan drug designations and approvals. To develop emerging good practices for RD outcomes research addressing the challenges inherent in identifying, selecting, developing, adapting, and implementing patient-reported outcome (PRO) and observer-reported outcome (ObsRO) assessments for use in RD clinical trials. This report outlines the challenges and potential solutions in determining clinical outcomes for RD trials. It follows the US Food and Drug Administration Roadmap to Patient-Focused Outcome Measurement in Clinical Trials. The Roadmap consists of three columns: 1) Understanding the Disease or Condition, 2) Conceptualizing Treatment Benefit, and 3) Selecting/Developing the Outcome Measure. Challenges in column 1 include factors such as incomplete natural history data and heterogeneity of disease presentation and patient experience. Solutions include using several information sources, for example, clinical experts and patient advocacy groups, to construct the condition's natural history and understand treatment patterns. Challenges in column 2 include understanding and measuring treatment benefit from the patient's perspective, especially given challenges in defining the context of use such as variations in age or disease severity/progression. Solutions include focusing on common symptoms across patient subgroups, identifying short-term outcomes, and using multiple types of COA instruments to measure the same constructs. Challenges in column 3 center around the small patient population and heterogeneity of the condition or study sample. Few disease-specific instruments for RDs exist. Strategies include adapting existing

Southern Appalachian assessment. Summary report, Report 1 of 5

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-07-01

This final report for the Southern Appalachian Man and the Biosphere Program is comprised of two documents: (1) a brief summary of programs and projects, and (2) a more extensive summary report included as an attachment. The purpose of the program is to promote a sustainable balance between the conservation of biological diversity, compatible economic uses, and cultural values across the Southern Appalachians. Program and project areas addressing regional issues include environmental monitoring and assessment, sustainable development/sustainable technologies, conservation biology, ecosystem management, environmental education and training, cultural and historical resources, and public information and education. The attached summary report is one of five that documents the results of the Southern Appalachian Assessment; it includes atmospheric, social/cultural/economic, terrestrial, and aquatic reports.

Assessment of current Dutch energy transition policy instruments for the existing housing stock

International Nuclear Information System (INIS)

Tambach, Milly; Hasselaar, Evert; Itard, Laure

2010-01-01

This research assesses to what extent current Dutch energy transition policy instruments for the existing housing stock can fulfil local executive actors' needs and instigate adoption of energy efficiency measures by them. This is done by studying energy policy instruments for the existing housing stock in the Netherlands and in other European countries, and by an empirical research, which analyses barriers and needs of local executive actors. We found that, despite current Dutch energy transition policy instruments for the existing housing stock seem to fulfil local executive actors' needs to a large extent, complementary policy instruments are needed to stimulate and pressure the incumbent renovation regime. A long-term oriented financial rewarding system is needed to build up a structural market for the deployment of renewables, to increase the number of specialist jobs in the building sector, and to stimulate the development of integrated, standardized, building components. Furthermore, a long-term oriented financial rewarding system for energy efficiency investments in housing renovation projects, and a low VAT rate applied to energy efficient renovation measures, are needed. Finally, enforcement possibilities and sanctions (fines) should become an integrative part of Dutch energy certification regulation to make the certificate become part of a value chain.

Indonesia - Country Procurement Assessment Report : Reforming the Public Procurement System

OpenAIRE

World Bank

2001-01-01

The main objectives of the Country Procurement Assessment Review (CPAR) are to diagnose the public procurement system in Indonesia, assess actual compliance with the country's procurement laws and regulations on the ground, and identify reforms to improve the existing system in line with internationally accepted principles. Section 1 gives an overview. Section 2 describes Indonesia's exist...

Do We Need Multiple Informants When Assessing Autistic Traits? The Degree of Report Bias on Offspring, Self, and Spouse Ratings

Science.gov (United States)

Möricke, Esmé; Buitelaar, Jan K.; Rommelse, Nanda N. J.

2016-01-01

This study focused on the degree of report bias in assessing autistic traits. Both parents of 124 preschoolers completed the Social Communication Questionnaire and the Autism-spectrum Quotient. Acceptable agreement existed between mother and father reports of children's mean scores of autistic traits, but interrater reliability for rank-order…

Clinician-Reported Outcome Assessments of Treatment Benefit: Report of the ISPOR Clinical Outcome Assessment Emerging Good Practices Task Force.

Science.gov (United States)

Powers, John H; Patrick, Donald L; Walton, Marc K; Marquis, Patrick; Cano, Stefan; Hobart, Jeremy; Isaac, Maria; Vamvakas, Spiros; Slagle, Ashley; Molsen, Elizabeth; Burke, Laurie B

2017-01-01

A clinician-reported outcome (ClinRO) assessment is a type of clinical outcome assessment (COA). ClinRO assessments, like all COAs (patient-reported, observer-reported, or performance outcome assessments), are used to 1) measure patients' health status and 2) define end points that can be interpreted as treatment benefits of medical interventions on how patients feel, function, or survive in clinical trials. Like other COAs, ClinRO assessments can be influenced by human choices, judgment, or motivation. A ClinRO assessment is conducted and reported by a trained health care professional and requires specialized professional training to evaluate the patient's health status. This is the second of two reports by the ISPOR Clinical Outcomes Assessment-Emerging Good Practices for Outcomes Research Task Force. The first report provided an overview of COAs including definitions important for an understanding of COA measurement practices. This report focuses specifically on issues related to ClinRO assessments. In this report, we define three types of ClinRO assessments (readings, ratings, and clinician global assessments) and describe emerging good measurement practices in their development and evaluation. The good measurement practices include 1) defining the context of use; 2) identifying the concept of interest measured; 3) defining the intended treatment benefit on how patients feel, function, or survive reflected by the ClinRO assessment and evaluating the relationship between that intended treatment benefit and the concept of interest; 4) documenting content validity; 5) evaluating other measurement properties once content validity is established (including intra- and inter-rater reliability); 6) defining study objectives and end point(s) objectives, and defining study end points and placing study end points within the hierarchy of end points; 7) establishing interpretability in trial results; and 8) evaluating operational considerations for the implementation of

Army Energy and Water Reporting System Assessment

Energy Technology Data Exchange (ETDEWEB)

Deprez, Peggy C.; Giardinelli, Michael J.; Burke, John S.; Connell, Linda M.

2011-09-01

There are many areas of desired improvement for the Army Energy and Water Reporting System. The purpose of system is to serve as a data repository for collecting information from energy managers, which is then compiled into an annual energy report. This document summarizes reported shortcomings of the system and provides several alternative approaches for improving application usability and adding functionality. The U.S. Army has been using Army Energy and Water Reporting System (AEWRS) for many years to collect and compile energy data from installations for facilitating compliance with Federal and Department of Defense energy management program reporting requirements. In this analysis, staff from Pacific Northwest National Laboratory found that substantial opportunities exist to expand AEWRS functions to better assist the Army to effectively manage energy programs. Army leadership must decide if it wants to invest in expanding AEWRS capabilities as a web-based, enterprise-wide tool for improving the Army Energy and Water Management Program or simply maintaining a bottom-up reporting tool. This report looks at both improving system functionality from an operational perspective and increasing user-friendliness, but also as a tool for potential improvements to increase program effectiveness. The authors of this report recommend focusing on making the system easier for energy managers to input accurate data as the top priority for improving AEWRS. The next major focus of improvement would be improved reporting. The AEWRS user interface is dated and not user friendly, and a new system is recommended. While there are relatively minor improvements that could be made to the existing system to make it easier to use, significant improvements will be achieved with a user-friendly interface, new architecture, and a design that permits scalability and reliability. An expanded data set would naturally have need of additional requirements gathering and a focus on integrating

Systematic Assessment Through Mathematical Model For Sustainability Reporting In Malaysia Context

Science.gov (United States)

Lanang, Wan Nurul Syahirah Wan; Turan, Faiz Mohd; Johan, Kartina

2017-08-01

Sustainability assessment have been studied and increasingly recognized as a powerful and valuable tool to measure the performance of sustainability in a company or industry. Nowadays, there are many existing tools that the users can use for sustainable development. There are various initiatives exists on tools for sustainable development, though most of the tools focused on environmental, economy and social aspects. Using the Green Project Management (GPM) P5 concept that suggests the firms not only needs to engage in mainly 3Ps principle: planet, profit, people responsible behaviours, but also, product and process need to be included in the practices, this study will introduce a new mathematical model for assessing the level of sustainability practice in the company. Based on multiple case studies, involving in-depth interviews with senior directors, feedback from experts, and previous engineering report, a systematic approach is done with the aims to obtain the respective data from the feedbacks and to be developed into a new mathematical model. By reviewing on the methodology of this research it comprises of several phases where it starts with the analyzation of the parameters and criteria selection according to the Malaysian context of industry. Moving on to the next step is data analysis involving regression and finally the normalisation process will be done to determine the result of this research either succeeded or not. Lastly, this study is expected to provide a clear guideline to any company or organization to assimilate the sustainability assessment in their development stage. In future, the better understanding towards the sustainability assessment is attained to be aligned unitedly in order to integrated the process approach into the systematic approach for the sustainability assessment.

Clinical Outcome Assessments: Conceptual Foundation-Report of the ISPOR Clinical Outcomes Assessment - Emerging Good Practices for Outcomes Research Task Force.

Science.gov (United States)

Walton, Marc K; Powers, John H; Hobart, Jeremy; Patrick, Donald; Marquis, Patrick; Vamvakas, Spiros; Isaac, Maria; Molsen, Elizabeth; Cano, Stefan; Burke, Laurie B

2015-09-01

An outcome assessment, the patient assessment used in an endpoint, is the measuring instrument that provides a rating or score (categorical or continuous) that is intended to represent some aspect of the patient's health status. Outcome assessments are used to define efficacy endpoints when developing a therapy for a disease or condition. Most efficacy endpoints are based on specified clinical assessments of patients. When clinical assessments are used as clinical trial outcomes, they are called clinical outcome assessments (COAs). COAs include any assessment that may be influenced by human choices, judgment, or motivation. COAs must be well-defined and possess adequate measurement properties to demonstrate (directly or indirectly) the benefits of a treatment. In contrast, a biomarker assessment is one that is subject to little, if any, patient motivational or rater judgmental influence. This is the first of two reports by the ISPOR Clinical Outcomes Assessment - Emerging Good Practices for Outcomes Research Task Force. This report provides foundational definitions important for an understanding of COA measurement principles. The foundation provided in this report includes what it means to demonstrate a beneficial effect, how assessments of patients relate to the objective of showing a treatment's benefit, and how these assessments are used in clinical trial endpoints. In addition, this report describes intrinsic attributes of patient assessments and clinical trial factors that can affect the properties of the measurements. These factors should be considered when developing or refining assessments. These considerations will aid investigators designing trials in their choice of using an existing assessment or developing a new outcome assessment. Although the focus of this report is on the development of a new COA to define endpoints in a clinical trial, these principles may be applied more generally. A critical element in appraising or developing a COA is to

Ecological Input Assessment and EIA: A Study On EIA Report For Quarry Projects

Directory of Open Access Journals (Sweden)

Rahimah Wahid

2016-12-01

Full Text Available The Environmental Impact Assessment (EIA was introduced as mandatory in Malaysia since 1988 as a measurement tool to achieve sustainable development. This study attempts to assess the EIA reports for quarrying activities which have been submitted to the Department of Environment. There are 19 scheduled activities requiring an EIA prior to project implementation. As the ecological input is an important part of the EIA report, these studies have tried to analyze the ecological quality of input in four EIA reports prepared for quarrying activities in Peninsular Malaysia. The results show that all aspects of the report comply with the review and sampling methods although there are deficiencies which may be remedied. Four EIA reports show weaknesses in the acquisition of the latest available data. For the preparation of the existing environment sections, the consultants do not feel inclined to make sampling on rock habitat, aquatic habitats and flora and fauna. The insulation measures suggested are not only exhaustive but also ineffective. The residual impact on the ecology is briefly mentioned in all the reports. Generally these EIA reports are found to have many shortcomings in the quality of ecological input and can be improved. Thus, a suggestion with a comprehensive approach and the cooperation of all parties is needed to sustain and complement the EIA.

Evaluation of the performance of existing non-laboratory based cardiovascular risk assessment algorithms

Science.gov (United States)

2013-01-01

Background The high burden and rising incidence of cardiovascular disease (CVD) in resource constrained countries necessitates implementation of robust and pragmatic primary and secondary prevention strategies. Many current CVD management guidelines recommend absolute cardiovascular (CV) risk assessment as a clinically sound guide to preventive and treatment strategies. Development of non-laboratory based cardiovascular risk assessment algorithms enable absolute risk assessment in resource constrained countries. The objective of this review is to evaluate the performance of existing non-laboratory based CV risk assessment algorithms using the benchmarks for clinically useful CV risk assessment algorithms outlined by Cooney and colleagues. Methods A literature search to identify non-laboratory based risk prediction algorithms was performed in MEDLINE, CINAHL, Ovid Premier Nursing Journals Plus, and PubMed databases. The identified algorithms were evaluated using the benchmarks for clinically useful cardiovascular risk assessment algorithms outlined by Cooney and colleagues. Results Five non-laboratory based CV risk assessment algorithms were identified. The Gaziano and Framingham algorithms met the criteria for appropriateness of statistical methods used to derive the algorithms and endpoints. The Swedish Consultation, Framingham and Gaziano algorithms demonstrated good discrimination in derivation datasets. Only the Gaziano algorithm was externally validated where it had optimal discrimination. The Gaziano and WHO algorithms had chart formats which made them simple and user friendly for clinical application. Conclusion Both the Gaziano and Framingham non-laboratory based algorithms met most of the criteria outlined by Cooney and colleagues. External validation of the algorithms in diverse samples is needed to ascertain their performance and applicability to different populations and to enhance clinicians’ confidence in them. PMID:24373202

HTGR market assessment: interim report

International Nuclear Information System (INIS)

1979-09-01

The purpose of this Assessment is to establish the utility perspective on the market potential of the HTGR. The majority of issues and conclusions in this report are applicable to both the HTGR-Gas Turbine (GT) and the HTGR-Steam Cycle (SC). This phase of the HTGR Market Assessment used the HTGR-GT as the reference design as it is the present focus of the US HTGR Program. A brief system description of the HTGR-GT is included in Appendix A. This initial report provides the proposed structure for conducting the HTGR Market Assessment plus preliminary analyses to establish the magnitude and nature of key factors that affect the HTGR market. The HTGR market factors and their relationship to the present HTGR Program are discussed. This report discusses two of these factors in depth: economics and water availability. The water availability situation in the US and its impact on the potential HTGR market are described. The approach for applying the HTGR within a framework of utility systems analyses is presented

National environmental/energy workforce assessment. South Dakota. Final report on phase 1

International Nuclear Information System (INIS)

1977-12-01

This study is one of 70 volumes assessing the workforce needs (manpower needs) for pollution control and abatement in the United States for the five-year period of 1976 through 1981. Seven fields for pollution control -- air, noise, pesticides, potable water, radiation, solid waste, and wastewater -- are analyzed, together with energy-related programs currently accentuated by the national effort to solve energy supply problems. The report identifies existing workforce levels, training programs, career opportunities, and future staffing level projections (1976 to 1982) based on the information available for the state of South Dakota

National environmental/energy workforce assessment. North Dakota. Final report on phase 1

International Nuclear Information System (INIS)

1977-12-01

This study is one of 70 volumes assessing the workforce needs (manpower needs) for pollution control and abatement in the United States for the five-year period of 1976 through 1981. Seven fields for pollution control -- air, noise, pesticides, potable water, radiation, solid waste, and wastewater -- are analyzed, together with energy-related programs currently accentuated by the national effort to solve energy supply problems. The report identifies existing workforce levels, training programs, career opportunities, and future staffing level projections (1976 to 1982) based on the information available for the state of North Dakota

National environmental/energy workforce assessment. New Mexico. Final report on phase 1

International Nuclear Information System (INIS)

1977-12-01

This study is one of 70 volumes assessing the workforce needs (manpower needs) for pollution control and abatement in the United States for the five-year period of 1976 through 1981. Seven fields for pollution control -- air, noise, pesticides, potable water, radiation, solid waste, and wastewater -- are analyzed, together with energy-related programs currently accentuated by the national effort to solve energy supply problems. The report identifies existing workforce levels, training programs, career opportunities, and future staffing level projections (1976 to 1982) based on the information available for the state of New Mexico

77 FR 29969 - Marine Mammal Stock Assessment Reports

Science.gov (United States)

2012-05-21

... Mammal Stock Assessment Reports AGENCY: National Marine Fisheries Service (NMFS), National Oceanic and... of marine mammal stock assessment reports (SARs). The 2011 reports are final and available to the... individual reports at the following address: http://www.nmfs.noaa.gov/pr/sars/ . You also may send requests...

Development of a quality instrument for assessing the spontaneous reports of ADR/ADE using Delphi method in China.

Science.gov (United States)

Chen, Lixun; Jiang, Ling; Shen, Aizong; Wei, Wei

2016-09-01

The frequently low quality of submitted spontaneous reports is of an increasing concern; to our knowledge, no validated instrument exists for assessing case reports' quality comprehensively enough. This work was conducted to develop such a quality instrument for assessing the spontaneous reports of adverse drug reaction (ADR)/adverse drug event (ADE) in China. Initial evaluation indicators were generated using systematic and literature data analysis. Final indicators and their weights were identified using Delphi method. The final quality instrument was developed by adopting the synthetic scoring method. A consensus was reached after four rounds of Delphi survey. The developed quality instrument consisted of 6 first-rank indicators, 18 second-rank indicators, and 115 third-rank indicators, and each rank indicator has been weighted. It evaluates the quality of spontaneous reports of ADR/ADE comprehensively and quantitatively on six parameters: authenticity, duplication, regulatory, completeness, vigilance level, and reporting time frame. The developed instrument was tested with good reliability and validity, which can be used to comprehensively and quantitatively assess the submitted spontaneous reports of ADR/ADE in China.

Data report for the safety assessment SR-Can

International Nuclear Information System (INIS)

Vahlund, Fredrik; Andersson, Johan; Loefgren, Martin

2006-11-01

This report is the data report derived within the project SR-Can. The purpose of the data report is to present input data, with uncertainty estimates, for the SR-Can assessment calculations. Data presented in the report have been derived using standardised procedures following a methodology which is presented in the initial part of the report. In this part, a template is presented that has been used when assessing input data in supporting documents as illustrated in subsequent chapters of the data report. By using the template, decisions by the SR-Can team are separated from expert input. This increases the traceability of assessment decisions. The data report supplies assessment data for all parts of the repository system, the fuel, the canister, the buffer and backfill and the geosphere. For the geosphere, many of the data are based on information obtained during the site investigation programme

Data report for the safety assessment SR-Can

Energy Technology Data Exchange (ETDEWEB)

Vahlund, Fredrik [Swedish Nuclear Fuel and Waste Management Co., Stockholm (Sweden); Andersson, Johan [JA Streamflow AB, Aelvsjoe (Sweden); Loefgren, Martin [Kemakta Konsult AB, Stockholm (Sweden)

2006-11-15

This report is the data report derived within the project SR-Can. The purpose of the data report is to present input data, with uncertainty estimates, for the SR-Can assessment calculations. Data presented in the report have been derived using standardised procedures following a methodology which is presented in the initial part of the report. In this part, a template is presented that has been used when assessing input data in supporting documents as illustrated in subsequent chapters of the data report. By using the template, decisions by the SR-Can team are separated from expert input. This increases the traceability of assessment decisions. The data report supplies assessment data for all parts of the repository system, the fuel, the canister, the buffer and backfill and the geosphere. For the geosphere, many of the data are based on information obtained during the site investigation programme.

Handheld Multi-Gas Meters Assessment Report

Energy Technology Data Exchange (ETDEWEB)

Williams, Gustavious [Brigham Young Univ., Provo, UT (United States); Wald-Hopkins, Mark David [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Obrey, Stephen J. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Akhadov, Valida Dushdurova [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2016-06-27

Handheld multi-gas meters (MGMs) are equipped with sensors to monitor oxygen (O2) levels and additional sensors to detect the presence of combustible or toxic gases in the environment. This report is limited to operational response-type MGMs that include at least four different sensors. These sensors can vary by type and by the monitored chemical. In real time, the sensors report the concentration of monitored gases in the atmosphere near the MGM. In April 2016 the System Assessment and Validation for Emergency Responders (SAVER) Program conducted an operationally-oriented assessment of MGMs. Five MGMs were assessed by emergency responders. The criteria and scenarios used in this assessment were derived from the results of a focus group of emergency responders with experience in using MGMs. The assessment addressed 16 evaluation criteria in four SAVER categories: Usability, Capability, Maintainability, and Deployability.

Measurement properties of existing clinical assessment methods evaluating scapular positioning and function. A systematic review

DEFF Research Database (Denmark)

Larsen, Camilla Marie; Juul-Kristensen, Birgit; Lund, Hans

%), with only one study rated as ‘good’. The reliability domain was most often investigated. Fewof the assessment methods in the included studies that had ‘fair’ or ‘good’ measurement properties demonstrated acceptable results for both reliability and validity.ConclusionWe found a substantially larger number......ABSTRACT OARSI Measurement properties of existing clinical assessment methods evaluating scapular positioning and function. A systematic review Larsen CM1, Juul-Kristensen B1,2 Lund H1,2, Søgaard K11University of Southern Denmark, Institute of Sports Science and Clinical Biomechanics2Institute...... assessment methods have measured the degree of scapular dyskinesis, subjectively by visual evaluation and objectively by measurements of static and dynamic scapular positioning, by either a 3-dimensional electromagnetic device or 2-dimensional clinically applicable methods. Since advanced equipment (i.e. 3D...

Co-Existence of Tuberous Sclerosis and the Fanconi Syndrome in Two Saudi Male Siblings: Report on Two Cases

International Nuclear Information System (INIS)

Al-Hwiesh, Abdulla K.; Al-Mueilo, Samir H.; Saeed, Ibrahim; Barak, Infal H.; Al-Muhanna, Fahd A.

2005-01-01

In this report, we present two cases of familial tuberous sclerosis co-existing with the Fanconi Syndrome. Both cases presented with history of failure to thrive and mental retardation associated with hypokalemic metabolic acidosis. To our knowledge, the association between tuberous sclerosis and the Fanconi Syndrome has not been reported previously. (author)

Review of international geothermal activities and assessment of US industry opportunities: Final report

Energy Technology Data Exchange (ETDEWEB)

1987-08-01

This study was initiated to review and assess international developments in the geothermal energy field and to define business opportunities for the US geothermal industry. The report establishes data bases on the status of worldwide geothermal development and the competitiveness of US industry. Other factors identified include existing legislation, tax incentives, and government institutions or agencies and private sector organizations that promote geothermal exports. Based on the initial search of 177 countries and geographic entities, 71 countries and areas were selected as the most likely targets for the expansion of the geothermal industry internationally. The study then determined to what extent their geothermal resource had been developed, what countries had aided or participated in this development, and what plans existed for future development. Data on the energy, economic, and financial situations were gathered.

Energy Efficiency Potential in Existing Commercial Buildings: Review of Selected Recent Studies

Energy Technology Data Exchange (ETDEWEB)

Belzer, David B.

2009-04-03

This report reviews six recent studies (from 2002 through 2006) by states and utilities to assess the energy saving potential in existing commercial buildings. The studies cover all or portions of California, Connecticut, Vermont, Colorado, Illinois, and the Pacific Northwest. The studies clearly reveal that lighting remains the single largest and most cost effective end use that can be reduced to save energy. Overall the study indicated that with existing technologies and costs, a reasonable range of economic savings potential in existing commercial buildings is between 10 and 20 percent of current energy use. While not a focus of the study, an additional conclusion is that implementation of commercial building monitoring and controls would also play an important role in the nation’s efforts to improve energy efficiency of existing buildings.

Transportation of Large Wind Components: A Review of Existing Geospatial Data

Energy Technology Data Exchange (ETDEWEB)

Mooney, Meghan [National Renewable Energy Lab. (NREL), Golden, CO (United States); Maclaurin, Galen [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2016-09-01

This report features the geospatial data component of a larger project evaluating logistical and infrastructure requirements for transporting oversized and overweight (OSOW) wind components. The goal of the larger project was to assess the status and opportunities for improving the infrastructure and regulatory practices necessary to transport wind turbine towers, blades, and nacelles from current and potential manufacturing facilities to end-use markets. The purpose of this report is to summarize existing geospatial data on wind component transportation infrastructure and to provide a data gap analysis, identifying areas for further analysis and data collection.

Final Report and Strategic Plan on the Feasibility Study to Assess Geothermal Potential on Warm Springs Reservation Lands. Report No. DOE/GO/15177

Energy Technology Data Exchange (ETDEWEB)

James Manion, Warm Springs Power & Water Enterprises; David McClain, McClain & Associates

2007-05-17

In 2005 the Confederated Tribes of Warm Springs Tribal Council authorized an evaluation of the geothermal development potential on the Confederated Tribes of Warm Springs Reservation of Oregon. Warm Springs Power & Water Enterprises obtained a grant from the U.S. Department of Energy to conduct a geological assessment and development estimate. Warm Springs Power & Water Enterprises utilized a team of expert consultants to conduct the study and develop a strategic plan. The resource assessment work was completed in 2006 by GeothermEx Inc., a consulting company specializing in geothermal resource assessments worldwide. The GeothermEx report indicates there is a 90% probability that a commercial geothermal resource exists on tribal lands in the Mt. Jefferson area. The geothermal resource assessment and other cost, risk and constraints information has been incorporated into the strategic plan.

Measuring and decomposing inequity in self-reported morbidity and self-assessed health in Thailand

Directory of Open Access Journals (Sweden)

Sidorenko Alexandra

2007-12-01

recent and chronic illness, while residence in the rural Northeast was the major contributor to the tendency of the poor to report lower levels of self-assessed health compared to peers. Conclusion The findings confirm that substantial socioeconomic inequalities in health as measured by self-reported morbidity and self-assessed health exist in Thailand. Decomposition analysis shows that inequalities in health status are associated with particular demographic, socioeconomic and geographic population subgroups. Vulnerable subgroups which are prone to both ill health and relative poverty warrant targeted policy attention.

Designing Second Language Performance Assessments. Technical Report.

Science.gov (United States)

Norris, John M.; Brown, James Dean; Hudson, Thom; Yoshioka, Jim

This technical report focuses on the decision-making potential provided by second language performance assessments. First, performance assessment is situated within the broader discussion of alternatives in language assessment and in educational assessment in general. Next, issues in performance assessment design, implementation, reliability, and…

IAEA Issues Report on Mission to Review Japan's Nuclear Power Plant Safety Assessment Process

International Nuclear Information System (INIS)

2012-01-01

Full text: A team of international nuclear safety experts has delivered its report on a mission it conducted from 21-31 January 2012 to review Japan's process for assessing nuclear safety at the nation's nuclear power plants. International Atomic Energy Agency (IAEA) officials delivered the IAEA Mission Report to Japanese officials yesterday and made it publicly available today. Following the 11 March 2011 accident at TEPCO's Fukushima Daiichi Nuclear Power Station, Japan's Nuclear and Industrial Safety Agency (NISA) announced the development of a revised safety assessment process for the nation's nuclear power reactors. At the request of the Government of Japan, the IAEA organized a team of five IAEA and three international nuclear safety experts and visited Japan to review NISA's approach to the Comprehensive Assessments for the Safety of Existing Power Reactor Facilities and how NISA examines the results submitted by nuclear operators. A Preliminary Summary Report was issued on 31 January. 'The mission report provides additional information regarding the team's recommendations and overall finding that NISA's instructions to power plants and its review process for the Comprehensive Safety Assessments are generally consistent with IAEA Safety Standards', said team leader James Lyons, Director of the IAEA's Nuclear Installation Safety Division. National safety assessments and their peer review by the IAEA are a key component of the IAEA Action Plan on Nuclear Safety, which was approved by the Agency's Member States following last year's nuclear accident at Fukushima Daiichi Nuclear Power Station. The IAEA safety review mission held meetings in Tokyo with officials from NISA, the Japanese Nuclear Energy Safety Organization (JNES), and the Kansai Electric Power Company (KEPCO), and the team visited the Ohi Nuclear Power Station to see an example of how Japan's Comprehensive Safety Assessment is being implemented by nuclear operators. In its report delivered today

Geosphere process report for the safety assessment SR-Site

International Nuclear Information System (INIS)

Skagius, Kristina

2010-11-01

This report documents geosphere processes identified as relevant to the long-term safety of a KBS-3 repository, and forms an important part of the reporting of the safety assessment SR-Site. The detailed assessment methodology, including the role of the process reports in the assessment, is described in the SR-Site Main report /SKB 2011/

Geosphere process report for the safety assessment SR-Site

Energy Technology Data Exchange (ETDEWEB)

Skagius, Kristina (ed.) (Kemakta Konsult AB, Stockholm (Sweden))

2010-11-15

This report documents geosphere processes identified as relevant to the long-term safety of a KBS-3 repository, and forms an important part of the reporting of the safety assessment SR-Site. The detailed assessment methodology, including the role of the process reports in the assessment, is described in the SR-Site Main report /SKB 2011/

Nuclear proliferation and civilian nuclear power. Report of the Nonproliferation Alternative Systems Assessment Program. Volume IV. Commercial potential

Energy Technology Data Exchange (ETDEWEB)

1980-06-01

This volume of the Nonproliferation Alternative Systems Assessment Program (NASAP) report provides time and cost estimates for positioning new nuclear power systems for commercial deployment. The assessment also estimates the rates at which the new systems might penetrate the domestic market, assuming the continuing viability of the massive light-water reactor network that now exists worldwide. This assessment does not recommend specific, detailed program plans and budgets for individual systems; however, it is clear from this analysis that any of the systems investigated could be deployed if dictated by national interest.

Nuclear proliferation and civilian nuclear power. Report of the Nonproliferation Alternative Systems Assessment Program. Volume IV. Commercial potential

International Nuclear Information System (INIS)

1980-06-01

This volume of the Nonproliferation Alternative Systems Assessment Program (NASAP) report provides time and cost estimates for positioning new nuclear power systems for commercial deployment. The assessment also estimates the rates at which the new systems might penetrate the domestic market, assuming the continuing viability of the massive light-water reactor network that now exists worldwide. This assessment does not recommend specific, detailed program plans and budgets for individual systems; however, it is clear from this analysis that any of the systems investigated could be deployed if dictated by national interest

Life cycle assessment of engineered nanomaterials: state of the art and strategies to overcome existing gaps.

Science.gov (United States)

Hischier, Roland; Walser, Tobias

2012-05-15

The use of engineered nanomaterials offers advantages as well as disadvantages from a sustainability perspective. It is important to identify such points as early as possible in order to be able to build on existing strengths, while counteracting disadvantages. Life Cycle Assessment (LCA) is a suitable method to assess the environmental performance of a product or process. But so far studies applying LCA to the area of nanotechnology have been scarce. One reason might be that the LCA framework has a whole list of issues that need further precision in order to be applicable to nanotechnologies: system boundaries and a functional unit have to be chosen in a way that allows one to do a comparison of equal functionalities; adequate and comprehensive life cycle inventory data for engineered nanomaterials are the key on the level of inventory analysis; and the impact assessment step requires a clear definition of the degree of detail on the level of nanoparticle emissions. The LCA studies existing thus far in the area of nanotechnology have barely begun to cover all these aspects. Thus, in order to improve the current situation, the authors propose to go ahead in each of the LCA stages as far as scientific advances allow. For the inventory modelling this means e.g. that comprehensive, transparently documented and quality ensured data of the most important engineered nanomaterials should be collected and made available in a widely-accepted format. Concerning nanoparticle emissions, as many parameters as possible have to be collected pertaining to the production, use, and the disposal phase of these engineered nanomaterials. Furthermore, on the level of impact assessment, relevant physical characteristics have to be identified for a toxicity assessment of nanoparticles and a consensus has to be found for a limited but sufficient number of independent parameters influencing toxicity to be collected. Copyright © 2012 Elsevier B.V. All rights reserved.

National Acid Precipitation Assessment Program Report to Congress: An Integrated Assessment

Energy Technology Data Exchange (ETDEWEB)

Uhart, M.; et al,

2005-08-01

Under Title IX of the 1990 Clean Air Act Amendments, Congress reauthorized the National Acid Precipitation Assessment Program (NAPAP) to continue coordinating acid rain research and monitoring, as it had done during the previous decade, and to provide Congress with periodic reports. In particular, Congress asked NAPAP to assess all available data and information to answer two questions: (1) What are the costs, benefits, and effectiveness of Title IV? This question addresses the costs and economic impacts of complying with the Acid Rain Program as well as benefit analyses associated with the various human health and welfare effects, including reduced visibility, damages to materials and cultural resources, and effects on ecosystems. (2) What reductions in deposition rates are needed to prevent adverse ecological effects? This complex questions addresses ecological systems and the deposition levels at which they experience harmful effects. The results of the assessment of the effects of Title IV and of the relationship between acid deposition rates and ecological effects were to be reported to Congress quadrennially, beginning with the 1996 report to Congress. The objective of this Report is to address the two main questions posed by Congress and fully communicate the results of the assessment to decision-makers. Given the primary audience, most of this report is not written as a technical document, although information supporting the conclusions is provided along with references.

Three Co-Existing Sexually Transmitted Diseases in a Heterosexual Male Youth: A Case Report

Directory of Open Access Journals (Sweden)

Theetat M. Surawan

2016-03-01

Full Text Available Most sexually transmitted diseases (STDs are asymptomatic, leading to widespread underdiagnoses estimated at 50% or higher. The presence of one STD significantly indicates an individual’s sexual health risk since an STD contributes to the transmission and acquisition of other STDs, including human immunodeficiency virus (HIV infection. Multiple co-existing STDs, thus, further increase the susceptibility of acquiring and transmitting HIV by twofold or more. Therefore, the comprehensive STD prevention strategies play a major role in reducing the transmission of HIV infection. We report an interesting case of a heterosexual male youth who presented at dermatology clinic with three concurrent sexually transmitted diseases: gonococcal urethritis, genital wart, and late latent syphilis. The case demonstrated significant issues for appropriate approaches and management of multiple co-existing STDs. Also, it reinforced the necessity for STD counselling for the patient, his partners, and family.

Prediction of difficult mask ventilation using a systematic assessment of risk factors vs. existing practice - a cluster randomised clinical trial in 94,006 patients

DEFF Research Database (Denmark)

Nørskov, A K; Wetterslev, J; Rosenstock, C V

2017-01-01

We compared implementation of systematic airway assessment with existing practice of airway assessment on prediction of difficult mask ventilation. Twenty-six departments were cluster-randomised to assess eleven risk factors for difficult airway management (intervention) or to continue with their......We compared implementation of systematic airway assessment with existing practice of airway assessment on prediction of difficult mask ventilation. Twenty-six departments were cluster-randomised to assess eleven risk factors for difficult airway management (intervention) or to continue...... with their existing airway assessment (control). In both groups, patients predicted as a difficult mask ventilation and/or difficult intubation were registered in the Danish Anaesthesia Database, with a notational summary of airway management. The trial's primary outcome was the respective incidence of unpredicted...... difficult and easy mask ventilation in the two groups. Among 94,006 patients undergoing mask ventilation, the incidence of unpredicted difficult mask ventilation in the intervention group was 0.91% and 0.88% in the control group; (OR) 0.98 (95% CI 0.66-1.44), p = 0.90. The incidence of patients predicted...

Estimation of the behavior factor of existing RC-MRF buildings

Science.gov (United States)

Vona, Marco; Mastroberti, Monica

2018-01-01

In recent years, several research groups have studied a new generation of analysis methods for seismic response assessment of existing buildings. Nevertheless, many important developments are still needed in order to define more reliable and effective assessment procedures. Moreover, regarding existing buildings, it should be highlighted that due to the low knowledge level, the linear elastic analysis is the only analysis method allowed. The same codes (such as NTC2008, EC8) consider the linear dynamic analysis with behavior factor as the reference method for the evaluation of seismic demand. This type of analysis is based on a linear-elastic structural model subject to a design spectrum, obtained by reducing the elastic spectrum through a behavior factor. The behavior factor (reduction factor or q factor in some codes) is used to reduce the elastic spectrum ordinate or the forces obtained from a linear analysis in order to take into account the non-linear structural capacities. The behavior factors should be defined based on several parameters that influence the seismic nonlinear capacity, such as mechanical materials characteristics, structural system, irregularity and design procedures. In practical applications, there is still an evident lack of detailed rules and accurate behavior factor values adequate for existing buildings. In this work, some investigations of the seismic capacity of the main existing RC-MRF building types have been carried out. In order to make a correct evaluation of the seismic force demand, actual behavior factor values coherent with force based seismic safety assessment procedure have been proposed and compared with the values reported in the Italian seismic code, NTC08.

Development of measures to assess the safety of existing NPPs and the effectiveness of regulations and regulatory actions (including 'prescriptive' and 'performance based' approaches). Peer discussions on regulatory practices

International Nuclear Information System (INIS)

1996-09-01

This report arises from the fourth series of peer discussions on regulatory practices entitled D evelopment of measures to assess the safety of existing nuclear power plants and the effectiveness of regulations and regulatory actions (including 'prescriptive' and 'performance based' approaches) . Senior regulators from 23 Member States participated in four peer group discussions during 1995-1996. This report presents the outcome of these meetings and recommendations of good practices identified by these senior regulators. The purpose of this report is to disseminate the views which the senior regulators presented at the meetings relating to measures used for assessing the safety of existing nuclear power plants and evaluating the effectiveness of regulators and regulatory actions. The intention in doing this is to assist Member States in the enhancement of their regulatory practices by identifying commonly accepted good practices. This report is structured so that it covers the subject matter under the following main headings: 'Prescriptive and Performance Based' Approaches to Regulation; Common Features of Regulatory Approaches; Effectiveness of the Regulator and Regulatory Actions; Recommendations of Good Practice. It is important to note that recommendations of good practice are included if they have been identified by at least one of the groups. It does not follow that all of the groups or individual Member States would necessarily endorse all of the recommendations. However, it is considered that if a single group of senior regulators judge that a particular practice is worthy of recommendation then it should be included for serious consideration. In some cases the same recommendations arise from all of the Groups

Assessment of inspectability of LMFBR designs. Final report

International Nuclear Information System (INIS)

1981-09-01

This two-volume report provides a comprehensive review of the inspectability of specific portions of loop- and pool-type LMFBR (1000-MWe) designs selected by EPRI. The designs were developed during the mid to late 1970s by three independent design teams (General Electric Co., Rockwell International, and Westinghouse) under the sponsorship of DOE (formerly ERDA) and EPRI. The requirements for normal, contingency, and post-repair inspections, addressed in this report, were established from Draft 12 of the ASME Boiler and Pressure Vessel Code, Section XI Division 3, issued in September 1979. These requirements, the intrinsic characteristics of the designs, the environmental (radiation, thermal, and atmospheric) aspects, and the available (present and near-term) inspection techniques, formed the basis for assessing the selected portions of the design or (1) accessibility, (2) feasibility, (3) practicality, and (4) costs to perform the above-specified inspections. Changes and additions fly ash has been as a concrete additive; however, extensive pilot scale development is underway to advance ash use in the TVA region in such areas as mineral and magnetite recovery, and mineral wool insulation. Recommended studies include: (1) the feasibility of converting existing wet fly d by the fuels include: residential (which includes residential and commercial), elthodology will be developed and verified in Phase II

34 CFR 200.8 - Assessment reports.

Science.gov (United States)

2010-07-01

... assessments under § 200.2 measured against the State's student academic achievement standards; and (ii) Help parents, teachers, and principals to understand and address the specific academic needs of students; and...) Student reports. A State's academic assessment system must produce individual student interpretive...

Assessment of patient-reported symptoms of anxiety

Science.gov (United States)

Rose, Matthias; Devine, Janine

2014-01-01

Patient self-reported symptoms are of crucial importance to identify anxiety disorders, as well as to monitor their treatment in clinical practice and research. Thus, for evidence-based medicine, a precise, reliable, and valid (ie, “objective”) assessment of the patient's reported “subjective” symptoms is warranted. There is a plethora of instruments available, which can provide psychometrically sound assessments of anxiety, but there are several limitations of current tools that need to be carefully considered for their successful use. Nevertheless, the empirical assessment of mental health status is not as accepted in medicine as is the assessment of biomarkers. One reason for this may be that different instruments assessing the same psychological construct use different scales. In this paper we present some new developments that promise to provide one common metric for the assessment of anxiety, to facilitate the general acceptance of mental health assessments in the future. PMID:25152658

Contract Reform Self Assessment Report

National Research Council Canada - National Science Library

1997-01-01

The primary objective of this self assessment is to report on the Department of Energy's progress in implementing the Contract Reform initiative launched in February 1994 and to discuss remaining challenges...

ASSESSMENT OF CONTROL TECHNOLOGIES FOR REDUCING EMISSIONS OF SO2 AND NOX FROM EXISTING COAL-FIRED UTILITY BOILERS

Science.gov (United States)

The report reviews information and estimated costs on 15 emissioncontrol technology categories applicable to existing coal-fired electric utility boilers. he categories include passive controls such as least emission dispatching, conventional processes, and emerging technologies ...

Safe reading of chemical pathology reports: the RCPAQAP Report Assessment Survey.

Science.gov (United States)

Koetsier, Sabrina; Jones, Graham Ross Dallas; Badrick, Tony

2016-06-01

Pathology reports are a vital component of the request-test-report cycle communicating pathology results to doctors to support clinical decision making. This should be done in a comprehensive, safe and time-efficient manner. As doctors may receive reports from different laboratories these goals can be achieved more readily if reports are formatted in the same way. This study evaluates the formatting of paper reports produced by Australian laboratories for numerical biochemistry results. As part of the RCPAQAP Liquid Serum Chemistry program in 2015, laboratories were invited to supply a routine paper report displaying the results. A total of 37 reports were received for analysis. These reports were assessed for variation in a range of components and, where possible, against relevant Australian standards and guidelines. In summary, there was a wide variation in most of the report components assessed including test names, result alignment, result flagging, sequence of data elements on the page, date formatting and patient name formatting. In most components there was also variation from the Standards. In order to ensure safe result transmission by printed reports there is a need to promote the adoption of current reporting standards and monitor compliance with similar external quality assurance programs. Crown Copyright © 2016. Published by Elsevier B.V. All rights reserved.

1998 FFTF annual system assessment reports

International Nuclear Information System (INIS)

Guttenberg, S.

1998-01-01

The health of FFTF systems was assessed assuming a continued facility standby condition. The review was accomplished in accordance with the guidelines of FFTF-EI-083, Plant Evaluation Program. The attached document includes an executive summary of the significant conclusions and assessment reports for each system evaluated

1998 FFTF annual system assessment reports

Energy Technology Data Exchange (ETDEWEB)

Guttenberg, S.

1998-03-19

The health of FFTF systems was assessed assuming a continued facility standby condition. The review was accomplished in accordance with the guidelines of FFTF-EI-083, Plant Evaluation Program. The attached document includes an executive summary of the significant conclusions and assessment reports for each system evaluated.

Hydroelectric potential of existing works in the Ardennes district - Preliminary study report, Feasibility study for the development of La Ferte-sur-Chiers, Feasibility study for the development of the Montherme site

International Nuclear Information System (INIS)

2010-02-01

A first document reports the analysis of five existing non-hydroelectric works. The objective is to see whether it is possible to equip them with a hydroelectric installation. For each of them, the report proposes a description of the site, a pre-diagnosis, a discussion of the regulatory framework, a hydrological analysis, a production assessment, and comments about a possible site rehabilitation. The next documents report feasibility studies performed for two of these sites. Each report presents the site and the adopted methodology, hydrological data, an analysis of the available height of fall, an analysis of environmental constraints, studied scenarios, a calculation of the possible production, a description of works to be performed, and a financial analysis

Southern Great Plains Rapid Ecoregional Assessment: pre-assessment report

Science.gov (United States)

Assal, Timothy J.; Melcher, Cynthia P.; Carr, Natasha B.

2015-01-01

The purpose of the Pre-Assessment Report for the Southern Great Plains Rapid Ecoregional Assessment (REA) is to document the selection process for and final list of Conservation Elements, Change Agents, and Management Questions developed during Phase I. The overall goal of the REAs being conducted for the Bureau of Land Management (BLM) is to provide information that supports regional planning and analysis for the management of ecological resources. The REA provides an assessment of baseline ecological conditions, an evaluation of current risks from drivers of ecosystem change, and a predictive capacity for evaluating future risks. The REA also may be used for identifying priority areas for conservation or restoration and for assessing the cumulative effects of a variety of land uses. There are several components of the REAs. Management Questions, developed by the BLM and partners for the ecoregion, identify the information needed for addressing land-management responsibilities. Conservation Elements represent regionally significant terrestrial and aquatic species and communities that are to be conserved and (or) restored. For each Conservation Element, key ecological attributes will be evaluated to determine the status of each species and community. The REA also will evaluate major drivers of ecosystem change, or Change Agents, currently affecting or likely to affect the status of Conservation Elements in the future. The relationships between Change Agents and key ecological attributes will be summarized using conceptual models. The REA process is a two-phase process. Phase I (pre-assessment) includes developing and finalizing the lists of priority Management Questions, Conservation Elements, and Change Agents, culminating in the REA Pre-Assessment Report.

Assessing middle school students` understanding of science relationships and processes: Year 2 - instrument validation. Final report

Energy Technology Data Exchange (ETDEWEB)

Schau, C.; Mattern, N.; Weber, R.; Minnick, K.

1997-01-01

Our overall purpose for this multi-year project was to develop an alternative assessment format measuring rural middle school students understanding of science concepts and processes and the interrelationships among them. This kind of understanding is called structural knowledge. We had 3 major interrelated goals: (1) Synthesize the existing literature and critically evaluate the actual and potential use of measures of structural knowledge in science education. (2) Develop a structural knowledge alternative assessment format. (3) Examine the validity of our structural knowledge format. We accomplished the first two goals during year 1. The structural knowledge assessment we identified and developed further was a select-and-fill-in concept map format. The goal for our year 2 work was to begin to validate this assessment approach. This final report summarizes our year 2 work.

Seismic assessment of existing RC buildings under alternative ground motion ensembles compatible to EC8 and NTC 2008

NARCIS (Netherlands)

Tanganelli, Marco; Viti, Stefania; Mariani, V.; Pianigiani, Maria

2017-01-01

This work investigates the effects of the choice of different ensembles of ground motions on the seismic assessment of existing RC buildings through nonlinear dynamic analysis. Nowadays indeed, all the main International Seismic Codes provide a soil classification which is based on the shear wave

Contact radiotherapy. Report of technological assessment

International Nuclear Information System (INIS)

Ortholan, Cecile; Melin, Nicole; Lee-Robin, Sun Hae; David, Denis Jean; Pages, Frederique; Devaud, Christine; Noel, Georges; Biga, Julie; Moty-Monnereau, Celine; Canet, Philippe; Lascols, Sylvie; Lamas, Muriel; Ramdine, Jessica; Tuil, Louise

2008-10-01

This report aims at assessing safety, indications, the role in therapeutic strategy, and efficiency of contact radiotherapy. It also aims at answering questions like: is the contact radiotherapy technique validated? What are the indications for contact radiotherapy? What about the efficiency and safety of contact radiotherapy? After a presentation of preliminary notions on radiotherapy (radiation types, dose, and irradiation techniques), the report presents this specific technique of contact radiotherapy: definition, devices, use recommendations, issues of radiation protection, modalities of performance of a contact radiotherapy session, and concerned pathologies. Then, based on a literature survey, this report addresses the various concerned tumours (skin, rectum, brain, breast), indicates some general information about these tumours (epidemiological data, anatomy and classification, therapeutic options, radiotherapy), and proposes an assessment of the efficiency and safety of contact radiotherapy

The Sandia Report and U.S. Achievement: An Assessment.

Science.gov (United States)

Stedman, Lawrence C.

1994-01-01

The article assesses the report of the Sandia National Laboratory's contentions about decline in Scholactic Aptitude Test Scores, National Assessment of Educational Progress achievement, and international assessments. The article suggests the report is generally right about steady trends but seriously flawed by several errors. (SM)

The landscape of existing models for high-throughput exposure assessment

DEFF Research Database (Denmark)

Jolliet, O.; Fantke, Peter; Huang, L.

2017-01-01

and ability to easily handle large datasets. For building materials a series of diffusion-based models have been developed to predict the chemicals emissions from building materials to indoor air, but existing models require complex analytical or numerical solutions, which are not suitable for LCA or HTS...... applications. Thus, existing model solutions needed to be simplified for application in LCA and HTS, and a parsimonious model has been developed by Huang et al. (2017) to address this need. For SVOCs, simplified solutions do exist, assuming constant SVOC concentrations in building materials and steadystate...... for skin permeation and volatilization as competing processes and that requires a limited number of readily available physiochemical properties would be suitable for LCA and HTS purposes. Thus, the multi-pathway exposure model for chemicals in cosmetics developed by Ernstoff et al.constitutes a suitable...

Report on the Pre-existing Condition Insurance Plan Program

Data.gov (United States)

U.S. Department of Health & Human Services — Before the Affordable Care Act, Americans with pre-existing conditions who did not receive health coverage through their employers had few affordable options to get...

Advanced Power Ultra-Uprates of Existing Plants (APPU) Final Scientific/Technical Report

Energy Technology Data Exchange (ETDEWEB)

Rubiolo, Pablo R. [Westinghouse Electric Company LLC, Pittsburgh, PA (United States). Science and Technology Dept.; Conway, Lawarence E. [Westinghouse Electric Company LLC, Pittsburgh, PA (United States). Science and Technology Dept.; Oriani, Luca [Westinghouse Electric Company LLC, Pittsburgh, PA (United States). Science and Technology Dept.; Lahoda, Edward J. [Westinghouse Electric Company LLC, Pittsburgh, PA (United States). Science and Technology Dept.; DeSilva, Greg [Westinghouse Electric Company LLC, Pittsburgh, PA (United States). Science and Technology Dept.; Hu, Min H. [Westinghouse Electric Company LLC, Pittsburgh, PA (United States). Nuclear Services Division; Hartz, Josh [Westinghouse Electric Company LLC, Pittsburgh, PA (United States). Nuclear Services Division; Bachrach, Uriel [Westinghouse Electric Company LLC, Pittsburgh, PA (United States). Nuclear Services Division; Smith, Larry [Westinghouse Electric Company LLC, Pittsburgh, PA (United States). Nuclear Services Division; Dudek, Daniel F. [Westinghouse Electric Company LLC, Pittsburgh, PA (United States). Nuclear Services Division; Toman, Gary J. [Electric Power Research Inst. (EPRI), Palo Alto, CA (United States); Feng, Dandong [Massachusetts Inst. of Technology (MIT), Cambridge, MA (United States); Hejzlar, Pavel [Massachusetts Inst. of Technology (MIT), Cambridge, MA (United States); Kazimi, Mujid S. [Massachusetts Inst. of Technology (MIT), Cambridge, MA (United States)

2006-03-31

This project assessed the feasibility of a Power Ultra-Uprate on an existing nuclear plant. The study determined the technical and design limitations of the current components, both inside and outside the containment. Based on the identified plant bottlenecks, the design changes for major pieces of equipment required to meet the Power Ultra-Uprate throughput were determined. Costs for modified pieces of equipment and for change-out and disposal of the replaced equipment were evaluated. These costs were then used to develop capital, fuel and operating and maintenance cost estimates for the Power Ultra-Uprate plant. The cost evaluation indicates that the largest cost components are the replacement of power (during the outage required for the uprate) and the new fuel loading. Based on these results, the study concluded that, for a standard 4-loop plant, the proposed Power Ultra-Uprate is technically feasible. However, the power uprate is likely to be more expensive than the cost (per Kw electric installed) of a new plant when large capacity uprates are considered (>25%). Nevertheless, the concept of the Power Ultra-Uprate may be an attractive option for specific nuclear power plants where a large margin exists in the steam and power conversion system or where medium power increases (~600 MWe) are needed. The results of the study suggest that development efforts on fuel technologies for current nuclear power plants should be oriented towards improving the fuel performance (fretting-wear, corrosion, uranium load, manufacturing, safety) required to achieve higher burnup rather focusing on potential increases in the fuel thermal output.

Advanced Power Ultra-Uprates of Existing Plants (APPU) Final Scientific/Technical Report

International Nuclear Information System (INIS)

Rubiolo, Pablo R.; Conway, Lawarence E.; Oriani, Luca; Lahoda, Edward J.; DeSilva, Greg; Hu, Min H.; Hartz, Josh; Bachrach, Uriel; Smith, Larry; Dudek, Daniel F.; Toman, Gary J.; Feng, Dandong; Hejzlar, Pavel; Kazimi, Mujid S.

2006-01-01

This project assessed the feasibility of a Power Ultra-Uprate on an existing nuclear plant. The study determined the technical and design limitations of the current components, both inside and outside the containment. Based on the identified plant bottlenecks, the design changes for major pieces of equipment required to meet the Power Ultra-Uprate throughput were determined. Costs for modified pieces of equipment and for change-out and disposal of the replaced equipment were evaluated. These costs were then used to develop capital, fuel and operating and maintenance cost estimates for the Power Ultra-Uprate plant. The cost evaluation indicates that the largest cost components are the replacement of power (during the outage required for the uprate) and the new fuel loading. Based on these results, the study concluded that, for a ''standard'' 4-loop plant, the proposed Power Ultra-Uprate is technically feasible. However, the power uprate is likely to be more expensive than the cost (per Kw electric installed) of a new plant when large capacity uprates are considered (>25%). Nevertheless, the concept of the Power Ultra-Uprate may be an attractive option for specific nuclear power plants where a large margin exists in the steam and power conversion system or where medium power increases (∼600 MWe) are needed. The results of the study suggest that development efforts on fuel technologies for current nuclear power plants should be oriented towards improving the fuel performance (fretting-wear, corrosion, uranium load, manufacturing, safety) required to achieve higher burnup rather focusing on potential increases in the fuel thermal output

Existing reporting guidelines for clinical trials are not completely relevant for implantable medical devices: a systematic review.

Science.gov (United States)

Motte, Anne-France; Diallo, Stéphanie; van den Brink, Hélène; Châteauvieux, Constance; Serrano, Carole; Naud, Carole; Steelandt, Julie; Alsac, Jean-Marc; Aubry, Pierre; Cour, Florence; Pellerin, Olivier; Pineau, Judith; Prognon, Patrice; Borget, Isabelle; Bonan, Brigitte; Martelli, Nicolas

2017-11-01

The aim of this study was to determine relevant items for reporting clinical trials on implantable medical devices (IMDs) and to identify reporting guidelines which include these items. A panel of experts identified the most relevant items for evaluating IMDs from an initial list based on reference papers. We then conducted a systematic review of articles indexed in MEDLINE. We retrieved reporting guidelines from the EQUATOR network's library for health research reporting. Finally, we screened these reporting guidelines to find those using our set of reporting items. Seven relevant reporting items were selected that related to four topics: randomization, learning curve, surgical setting, and device information. A total of 348 reporting guidelines were identified, among which 26 met our inclusion criteria. However, none of the 26 reporting guidelines presented all seven items together. The most frequently reported item was timing of randomization (65%). On the contrary, device information and learning curve effects were poorly specified. To our knowledge, this study is the first to identify specific items related to IMDs in reporting guidelines for clinical trials. We have shown that no existing reporting guideline is totally suitable for these devices. Copyright © 2017 Elsevier Inc. All rights reserved.

Existence of Projective Planes

OpenAIRE

Perrott, Xander

2016-01-01

This report gives an overview of the history of finite projective planes and their properties before going on to outline the proof that no projective plane of order 10 exists. The report also investigates the search carried out by MacWilliams, Sloane and Thompson in 1970 [12] and confirms their result by providing independent verification that there is no vector of weight 15 in the code generated by the projective plane of order 10.

Interim process report for the safety assessment SR-Can

International Nuclear Information System (INIS)

Sellin, Patrick

2004-08-01

This report is a documentation of buffer processes identified as relevant to the long-term safety of a KBS-3 repository. The report is part of the interim reporting of the safety assessment SR-Can, see further the Interim main report. The final SR-Can reporting will support SKB's application to build an Encapsulation plant for spent nuclear fuel and is to be produced in 2006. The purpose of this report is to document the scientific knowledge of the processes to a level required for an adequate treatment in the safety assessment. The documentation is thus from a scientific point of not exhaustive since such a treatment is neither necessary for the purposes of the safety assessment nor possible within the scope of an assessment. The purpose is further to determine the handling of each process in the safety assessment and to demonstrate how uncertainties are taken care of, given the suggested handling. The process documentation in the SR 97 version of the Process report is a starting point for this SR-Can interim version. As further described in the Interim main report, the list of relevant processes has been reviewed and slightly extended by comparison to other databases. Furthermore, the backfill has been included as a system part of its own, rather than being described together with the buffer as in SR 97. Apart from giving an interim account of the documentation and handling of buffer processes in SR-Can, this report is meant to serve as a template for the forthcoming documentation of processes occurring in other parts of the repository system. A complete list of processes can be found in the Interim FEP report for the safety assessment SR-Can. All material presented in this document is preliminary in nature and will possibly be updated as the SR-Can project progresses

Interim process report for the safety assessment SR-Can

Energy Technology Data Exchange (ETDEWEB)

Sellin, Patrick (ed.)

2004-08-01

This report is a documentation of buffer processes identified as relevant to the long-term safety of a KBS-3 repository. The report is part of the interim reporting of the safety assessment SR-Can, see further the Interim main report. The final SR-Can reporting will support SKB's application to build an Encapsulation plant for spent nuclear fuel and is to be produced in 2006. The purpose of this report is to document the scientific knowledge of the processes to a level required for an adequate treatment in the safety assessment. The documentation is thus from a scientific point of not exhaustive since such a treatment is neither necessary for the purposes of the safety assessment nor possible within the scope of an assessment. The purpose is further to determine the handling of each process in the safety assessment and to demonstrate how uncertainties are taken care of, given the suggested handling. The process documentation in the SR 97 version of the Process report is a starting point for this SR-Can interim version. As further described in the Interim main report, the list of relevant processes has been reviewed and slightly extended by comparison to other databases. Furthermore, the backfill has been included as a system part of its own, rather than being described together with the buffer as in SR 97. Apart from giving an interim account of the documentation and handling of buffer processes in SR-Can, this report is meant to serve as a template for the forthcoming documentation of processes occurring in other parts of the repository system. A complete list of processes can be found in the Interim FEP report for the safety assessment SR-Can. All material presented in this document is preliminary in nature and will possibly be updated as the SR-Can project progresses.

Existing Default Values and Recommendations for Exposure Assessment - A Nordic Exposure Group Project 2011

DEFF Research Database (Denmark)

Höglund, Lena; Räisänen, Jouni; Hämäläinen, Anne-Maija

range of more or less well-documented values originating from many different sources. The purpose of this report is to give an overview and to evaluate exposure factors that are currently used by the authorities and industry in the exposure assessments for both adults (occupational and consumer exposure......) and children in relation to REACH. Another important purpose of the report is to contribute towards a further harmonisation of exposure factors by giving recommendations of most valid and representative defaults. These recommendations can be used besides REACH also in biocide's and plant protection product...

Screening report : Municipality of Leamington : Leamington Pollution Control Centre stand-by emergency power class environmental assessment

Energy Technology Data Exchange (ETDEWEB)

NONE

2009-03-15

The Leamington Pollution Control Centre (PCC) is located in Ontario and treats residential and commercial wastewater collected from the Municipality of Leamington. The Leamington PCC currently has one standby diesel generator with a rated capacity of 545 kW. This generator provides power to the plant's disinfection facilities to reduce the risk of back-up into the collection system during power failures. The Municipality of Leamington plans to provide treatment in addition to disinfection during power outages. In order to achieve this, additional standby power is required to run the primary clarifiers, the aeration system and the secondary clarifiers. This document presented a screening report for the new standby generator, whose installation is considered a Schedule B under the Municipal Class Environmental Assessment process. The report reviewed background information on the proposed project; Ontario's Environmental Assessment Act; and the Class Environmental Assessment Act. It outlined the problem statement; identification of solutions; existing conditions; impacts and mitigation during construction and operation; and public consultation procedures. 2 refs., 4 figs., 1 appendix.

List of unrestricted NIM reports and papers published during the first decade of NIM'S existence (1966 to 1975)

International Nuclear Information System (INIS)

Paynter, J.C.; Glen, H.W.

1976-01-01

This publication lists the 554 unrestricted reports and 200 papers published by the National Institute for Metallurgy during the first ten years of its existence. For ease of reference, these publications are also classified under the research programmes that gave rise to them [af

Millennium Ecosystem Assessment Synthesis Report. Pre-publication. Final Draft Approved by MA Board on March 23, 2005. A Report of the Millennium Ecosystem Assessment

International Nuclear Information System (INIS)

Reid, W.V.; Mooney, H.A.; Cropper, A.; Capistrano, D.; Carpenter, S.R.; Chopra, K.; Dasgupta, P.; Dietz, T.; Duraiappah, A.K.; Hassan, R.; Kasperson, R.; Leemans, R.; May, R.M.; McMichael, T.; Pingali, P.; Samper, C.; Scholes, R.; Watson, R.T.; Zakri, A.H.; Shidong, Z.; Ash, N.J.; Bennett, E.; Kumar, P.; Lee, M.J.; Raudsepp-Hearne, C.; Simons, H.; Thonell, J.; Zurek, M.B.

2005-01-01

This report presents a synthesis and integration of the findings of the four MA (Millennium Assessment) Working Groups along with more detailed findings for selected ecosystem services concerning condition and trends and scenarios and response options. Five additional synthesis reports were prepared for ease of use by specific audiences: CBD (biodiversity), UNCCD (desertification), Ramsar Convention (wetlands), business, and the health sector. Each MA sub-global assessment will also produce additional reports to meet the needs of its own audience. The full technical assessment reports of the four MA Working Groups will be published in mid-2005 by Island Press. All printed materials of the assessment, along with core data and a glossary of terminology used in the technical reports, will be available on the Internet at www.MAweb.org. Appendix D lists the acronyms and abbreviations used in this report and includes additional information on sources for some of the Figures in this report

Documenting Matured Science: The BACC-Type Assessment Reports

Science.gov (United States)

Reckermann, M.; Omstedt, A. T.

2016-12-01

The BACC-type reports (BALTEX and Baltic Earth Assessment of Climate Change for the Baltic Sea region, BACC 2008 and BACC II 2015) represent an approach to assessing and making available current knowledge on regional climate change and its regional impacts on the physical, biogeochemical and biological environment (ecosystems, socio-economic sphere). The BACC assessments have originated in the BALTEX scientific research community (now Baltic Earth) and are coordinated by the International Baltic Earth Secretariat. The assessments are produced by teams of scientists from the region, led by lead authors who recruit experts from relevant topics to contribute. The report of 2015 was compiled by a different group of authors as 2008 to warrant independence of personal opinions and bias. The process is not externally funded and completely based on published scientific evidence, and not biased by political or economic interest groups. The BACC-type reports aim to bring together consolidated knowledge that has broad consensus in the scientific community, but also acknowledging issues for which contradicting opinions are found in the literature, so that no consensus can be reached ("consensus on dissensus"). An international steering committee is responsible for overlooking the process, and all manuscripts are anonymously peer-reviewed by independent international experts. Outreach to stakeholders and the public is an inherent aspect of this approach to document mature science. For the Baltic Sea, there is a close collaboration with HELCOM, the intergovernmental Baltic Marine Environment Protection Commission and the major regional science-policy interface in the Baltic Sea region. A summary for non-scientists was produced for the first BACC report and is in preparation for the second. Other BACC-type reports published are the climate report for the greater Hamburg area (published in 2011), and the NOSCCA report (North Sea Climate Change Assessment), published in 2016.

National Acid Precipitation Assessment Program: 1990 Integrated Assessment report

International Nuclear Information System (INIS)

1991-11-01

The document, the 'Integrated Assessment,' is a summary of the causes and effects of acidic deposition and a comparison of the costs and effectiveness of alternative emission control scenarios. In developing the 'Integrated Assessment,' it was NAPAP's goal to produce a structured compilation of policy-relevant technical information. The Integrated Assessment is based on findings and data from a series of twenty-seven State-of-Science/Technology Reports (SOS/T) on acidic deposition published by NAPAP in 1990. The scope of the documents includes: (1) emissions, atmospheric processes and deposition; (2) effects on surface waters, forests, agricultural crops, exposed materials, human health, and visibility; and (3) control technologies, future emissions, and effects valuation

FMDP reactor alternative summary report. Volume 1 - existing LWR alternative

International Nuclear Information System (INIS)

Greene, S.R.; Bevard, B.B.

1996-01-01

Significant quantities of weapons-usable fissile materials [primarily plutonium and highly enriched uranium (HEU)] are becoming surplus to national defense needs in both the United States and Russia. These stocks of fissile materials pose significant dangers to national and international security. The dangers exist not only in the potential proliferation of nuclear weapons but also in the potential for environmental, safety, and health (ES ampersand H) consequences if surplus fissile materials are not properly managed. This document summarizes the results of analysis concerned with existing light water reactor plutonium disposition alternatives

FMDP reactor alternative summary report. Volume 1 - existing LWR alternative

Energy Technology Data Exchange (ETDEWEB)

Greene, S.R.; Bevard, B.B. [and others

1996-10-07

Significant quantities of weapons-usable fissile materials [primarily plutonium and highly enriched uranium (HEU)] are becoming surplus to national defense needs in both the United States and Russia. These stocks of fissile materials pose significant dangers to national and international security. The dangers exist not only in the potential proliferation of nuclear weapons but also in the potential for environmental, safety, and health (ES&H) consequences if surplus fissile materials are not properly managed. This document summarizes the results of analysis concerned with existing light water reactor plutonium disposition alternatives.

Site 300 hazardous-waste-assessment project. Interim report: December 1981. Preliminary site reconnaissance and project work plan

International Nuclear Information System (INIS)

Raber, E.; Helm, D.; Carpenter, D.; Peifer, D.; Sweeney, J.

1982-01-01

This document was prepared to outline the scope and objectives of the Hazardous Waste Assessment Project (HWAP) at Site 300. This project was initiated in October, 1981, to investigate the existing solid waste landfills in an effort to satisfy regulatory guidelines and assess the potential for ground-water contamination. This involves a site-specific investigation (utilizing geology, hydrology, geophysics and geochemistry) with the goal of developing an effective ground-water quality monitoring network. Initial site reconnaissance work has begun and we report the results, to date, of our geologic hydrogeologic studies. All known solid waste disposal locations are underlain by rocks of either the Late Miocene Neroly Formation or the Cierbo Formation, both of which are dominantly sandstones interbedded with shale and claystone. The existence of a regional confined (artesian) aquifer, as well as a regional water-table aquifer is postulated for Site 300. Preliminary analysis has led to an understanding of directions and depths of regional ground-water flow

Trempel hydropower station - renewal and extension of the existing plant

International Nuclear Information System (INIS)

Binder, F.M.; Burri, J.

2003-01-01

This final report for the Swiss Federal Office of Energy (SFOE) presents the results of a study made on the refurbishment and/or extension of a 450 kW hydropower plant near Krummenau, Switzerland. Three possible variants are presented, one involving the renewal of the installation and two variants for enhancing production to provide 1 MW and 2.25 MW of power respectively. Details on the hydrology of the location are given and the equipment of the existing two-turbine power station is described. Residual water questions are discussed and the civil works envisaged are described. The report also presents data on the economics of the project and assesses the effects on the environment, landscape and ground water it would bring with it

Development of a general method for detection and quantification of the P35S promoter based on assessment of existing methods

Science.gov (United States)

Wu, Yuhua; Wang, Yulei; Li, Jun; Li, Wei; Zhang, Li; Li, Yunjing; Li, Xiaofei; Li, Jun; Zhu, Li; Wu, Gang

2014-01-01

The Cauliflower mosaic virus (CaMV) 35S promoter (P35S) is a commonly used target for detection of genetically modified organisms (GMOs). There are currently 24 reported detection methods, targeting different regions of the P35S promoter. Initial assessment revealed that due to the absence of primer binding sites in the P35S sequence, 19 of the 24 reported methods failed to detect P35S in MON88913 cotton, and the other two methods could only be applied to certain GMOs. The rest three reported methods were not suitable for measurement of P35S in some testing events, because SNPs in binding sites of the primer/probe would result in abnormal amplification plots and poor linear regression parameters. In this study, we discovered a conserved region in the P35S sequence through sequencing of P35S promoters from multiple transgenic events, and developed new qualitative and quantitative detection systems targeting this conserved region. The qualitative PCR could detect the P35S promoter in 23 unique GMO events with high specificity and sensitivity. The quantitative method was suitable for measurement of P35S promoter, exhibiting good agreement between the amount of template and Ct values for each testing event. This study provides a general P35S screening method, with greater coverage than existing methods. PMID:25483893

Methodology for the assessment of the impact of existing high voltage lines in urban areas

International Nuclear Information System (INIS)

Sumper, Andreas; Boix-Aragones, Oriol; Villafafila-Robles, Roberto; Bergas-Jane, Joan; Ramirez-Pisco, Rodrigo

2010-01-01

This paper presents a methodology for the assessment of the impact of existing high voltage lines in urban areas. This methodology is based on the numeric evaluation of several impacts which are combined with weight factors. The novelty is that it opens up the possibility of citizen participation, basically in the way in which impacts and weighting factors are determined. The proposed methodology has been applied first in the municipality of Rubi, a mid-sized town near Barcelona, and later on in several municipalities in the Catalonia region in Spain. The results were used to prioritise mitigation action in the Catalonia Energy Plan.

Biomass Gasification Technology Assessment: Consolidated Report

Energy Technology Data Exchange (ETDEWEB)

Worley, M.; Yale, J.

2012-11-01

Harris Group Inc. (HGI) was commissioned by the National Renewable Energy Laboratory to assess gasification and tar reforming technologies. Specifically, the assessments focused on gasification and tar reforming technologies that are capable of producing a syngas suitable for further treatment and conversion to liquid fuels. HGI gathered sufficient information to analyze three gasification and tar reforming systems. This report summarizes the equipment, general arrangement of the equipment, operating characteristics, and operating severity for each technology. The order of magnitude capital cost estimates are supported by a basis-of-estimate write-up, which is also included in this report. The report also includes Microsoft Excel workbook models, which can be used to design and price the systems. The models can be used to analyze various operating capacities and pressures. Each model produces a material balance, equipment list, capital cost estimate, equipment drawings and preliminary general arrangement drawings. Example outputs of each model are included in the Appendices.

B Plant low level waste system integrity assessment report

International Nuclear Information System (INIS)

Walter, E.J.

1995-09-01

This document provides the report of the integrity assessment activities for the B Plant low level waste system. The assessment activities were in response to requirements of the Washington State Dangerous Waste Regulations, Washington Administrative Code (WAC), 173-303-640. This integrity assessment report supports compliance with Hanford Federal Facility Agreement and Consent Order interim milestone target action M-32-07-T03

Analysis of existing risk assessments, and list of suggestions

CERN Document Server

Heimsch, Laura

2016-01-01

The scope of this project was to analyse risk assessments made at CERN and extracting some crucial information about the different methodologies used, profiles of people who make the risk assessments, and gathering information of whether the risk matrix was used and if the acceptable level of risk was defined. Second step of the project was to trigger discussion inside HSE about risk assessment by suggesting a risk matrix and a risk assessment template.

Pre-Tiger Team Self-Assessment report

International Nuclear Information System (INIS)

1991-01-01

The Sandia National Laboratories Pre-Tiger Team Self-Assessment Report contains an introduction that describes the three sites in Albuquerque, New Mexico, Kauai, Hawaii, and Tonopah, Nevada, and the activities associated therewith. The self-assessment was performed October 1990 through December 1990. The paper discusses key findings and root causes associated with problem areas; environmental protection assessment with respect to the Clean Air Act, Clean Water Act, Comprehensive Environmental Response, Compensation, and Liability Act and the Superfund amendments, Resource Conservation and Recovery Act; and other regulatory documents; safety and health assessment with respect to organization administration, quality assurance, maintenance, training, emergency preparedness, nuclear criticality safety, security/safety interface, transportation, radiation protection, occupational safety, and associated regulations; and management practices assessment. 5 figs

Navy radon assessment and mitigation program: Final report

International Nuclear Information System (INIS)

1994-10-01

This final report encompasses the events from the beginning of the Navy Radon Assessment and Mitigation Program to the closure of the program on October 31, 1994. Included in the report are discussions of the phases of the program including screening, assessment, mitigation, and post-mitigation. The primary discussion involves screening and assessment. The report addresses recommendations made to the Naval Facilities Engineering Command by the Hazardous Waste Remedial Actions Program of Martin Marietta Energy Systems, Inc., and the final decisions that were made. Special emphasis is placed on quality assurance/quality control (QA/QC), since QA/QC was given top priority during the implementation of this program. Included in the discussion on QA/QC are ana overview of the measurement process, positive and negative controls, replicated measurements, and application of chamber exposures to data calibration. The report concludes with a discussion of testing considerations for naval facilities and radon mitigation considerations for the Department of the Navy

Fuel and canister process report for the safety assessment SR-Site

International Nuclear Information System (INIS)

Werme, Lars; Lilja, Christina

2010-12-01

This report documents fuel and canister processes identified as relevant to the long-term safety of a KBS-3 repository. It forms an important part of the reporting of the safety assessment SR-Site. The detailed assessment methodology, including the role of the process reports in the assessment, is described in the SR-Site Main report /SKB 2011/

Fuel and canister process report for the safety assessment SR-Site

Energy Technology Data Exchange (ETDEWEB)

Werme, Lars; Lilja, Christina (eds.)

2010-12-15

This report documents fuel and canister processes identified as relevant to the long-term safety of a KBS-3 repository. It forms an important part of the reporting of the safety assessment SR-Site. The detailed assessment methodology, including the role of the process reports in the assessment, is described in the SR-Site Main report /SKB 2011/

Patient- and Caregiver-Reported Assessment Tools for Palliative Care: Summary of the 2017 Agency for Healthcare Research and Quality Technical Brief.

Science.gov (United States)

Aslakson, Rebecca A; Dy, Sydney M; Wilson, Renee F; Waldfogel, Julie; Zhang, Allen; Isenberg, Sarina R; Blair, Alex; Sixon, Joshua; Lorenz, Karl A; Robinson, Karen A

2017-12-01

Assessment tools are data collection instruments that are completed by or with patients or caregivers and which collect data at the individual patient or caregiver level. The objectives of this study are to 1) summarize palliative care assessment tools completed by or with patients or caregivers and 2) identify needs for future tool development and evaluation. We completed 1) a systematic review of systematic reviews; 2) a supplemental search of previous reviews and Web sites, and/or 3) a targeted search for primary articles when no tools existed in a domain. Paired investigators screened search results, assessed risk of bias, and abstracted data. We organized tools by domains from the National Consensus Project Clinical Practice Guidelines for Palliative Care and selected the most relevant, recent, and highest quality systematic review for each domain. We included 10 systematic reviews and identified 152 tools (97 from systematic reviews and 55 from supplemental sources). Key gaps included no systematic review for pain and few tools assessing structural, cultural, spiritual, or ethical/legal domains, or patient-reported experience with end-of-life care. Psychometric information was available for many tools, but few studies evaluated responsiveness (sensitivity to change) and no studies compared tools. Few to no tools address the spiritual, ethical, or cultural domains or patient-reported experience with end-of-life care. While some data exist on psychometric properties of tools, the responsiveness of different tools to change and/or comparisons between tools have not been evaluated. Future research should focus on developing or testing tools that address domains for which few tools exist, evaluating responsiveness, and comparing tools. Copyright © 2017 American Academy of Hospice and Palliative Medicine. All rights reserved.

The Adaptation Gap Report. Towards Global Assessment

DEFF Research Database (Denmark)

2017-01-01

The Paris Agreement, adopted in 2015, established the global goal on adaptation of enhancing adaptive capacity, strengthening resilience and reducing vulnerability to climate change, with a view to contributing to sustainable development and ensuring an adequate adaptation response in the context...... Change (UNFCCC) to prepare for the implementation of the Paris Agreement. In contrast to previous Adaptation Gap Reports, the 2017 report focuses on issues relating to frameworks, comprising concepts, methodologies and data, rather than on assessing a particular dimension of the adaptation gap. Future...... extensive external review. The Paris Agreement’s global goal on adaptation provides a new starting point and impetus for assessing progress on adaptation at the global level, but additional information is required for assessing such progress. The global goal on adaptation provides a collective vision...

Integrated safety assessment report: Integrated Safety Assessment Program: Millstone Nuclear Power Station, Unit 1 (Docket No. 50-245): Draft report

International Nuclear Information System (INIS)

1987-04-01

The Integrated Safety Assessment Program (ISAP) was initiated in November 1984, by the US Nuclear Regulatory Commission to conduct integrated assessments for operating nuclear power reactors. The integrated assessment is conducted in a plant-specific basis to evaluate all licensing actions, licensee initiated plant improvements and selected unresolved generic/safety issues to establish implementation schedules for each item. In addition, procedures will be established to allow for a periodic updating of the schedules to account for licensing issues that arise in the future. This report documents the review of Millstone Nuclear Power Station, Unit No. 1, operated by Northeast Nuclear Energy Company (located in Waterford, Connecticut). Millstone Nuclear Power Station, Unit No. 1, is one of two plants being reviewed under the pilot program for ISAP. This report indicates how 85 topics selected for review were addressed. This report presents the staff's recommendations regarding the corrective actions to resolve the 85 topics and other actions to enhance plant safety. The report is being issued in draft form to obtain comments from the licensee, nuclear safety experts, and the Advisory Committee for Reactor Safeguards (ACRS). Once those comments have been resolved, the staff will present its positions, along with a long-term implementation schedule from the licensee, in the final version of this report

Final voluntary release assessment/corrective action report

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-11-12

The US Department of Energy, Carlsbad Area Office (DOE-CAO) has completed a voluntary release assessment sampling program at selected Solid Waste Management Units (SWMUs) at the Waste Isolation Pilot Plant (WIPP). This Voluntary Release Assessment/Corrective Action (RA/CA) report has been prepared for final submittal to the Environmental protection Agency (EPA) Region 6, Hazardous Waste Management Division and the New Mexico Environment Department (NMED) Hazardous and Radioactive Materials Bureau to describe the results of voluntary release assessment sampling and proposed corrective actions at the SWMU sites. The Voluntary RA/CA Program is intended to be the first phase in implementing the Resource Conservation and Recovery Act (RCRA) Facility Investigation (RFI) and corrective action process at the WIPP. Data generated as part of this sampling program are intended to update the RCRA Facility Assessment (RFA) for the WIPP (Assessment of Solid Waste Management Units at the Waste Isolation Pilot Plant), NMED/DOE/AIP 94/1. This Final Voluntary RA/CA Report documents the results of release assessment sampling at 11 SWMUs identified in the RFA. With this submittal, DOE formally requests a No Further Action determination for these SWMUs. Additionally, this report provides information to support DOE`s request for No Further Action at the Brinderson and Construction landfill SWMUs, and to support DOE`s request for approval of proposed corrective actions at three other SWMUs (the Badger Unit Drill Pad, the Cotton Baby Drill Pad, and the DOE-1 Drill Pad). This information is provided to document the results of the Voluntary RA/CA activities submitted to the EPA and NMED in August 1995.

First safety assessment objectives and content of the 2001 report

International Nuclear Information System (INIS)

Franco, Michel de

2002-01-01

Michel de Franco (ANDRA, France) described plans to report its first safety assessment of facility designs for disposal of high and intermediate level waste and spent fuel. This assessment will be the forerunner of a more detailed assessment that is required to be presented to the French government in 2005 and is intended to facilitate the formalization and testing of the assessment methodology intended to be used in the 2005 assessment report. The report will include information about the waste inventory, the materials used for the engineered barriers and current understanding of the geology and surface environment at the Bure site in eastern France. It will also describe the preliminary design concepts and the phenomena defining the evolution of the repository in different time frames as well as presenting the results of the initial performance assessment of the repository. The report will also include an analysis of the implications of the requirement for reversibility, taken to mean that each repository development step can be reversed

Measurement properties of existing clinical assessment methods evaluating scapular positioning and function. A systematic review

DEFF Research Database (Denmark)

Larsen, Camilla Marie; Juul-Kristensen, Birgit; Lund, Hans

2014-01-01

a substantially larger number of clinical scapular assessment methods than previously reported. Using the COSMIN checklist the methodological quality of the included measurement properties in the reliability and validity domains were in general ‘‘fair’’ to ‘‘poor’’. None were examined for all three domains: (1...... utility for clinical practice.......The aims were to compile a schematic overview of clinical scapular assessment methods and critically appraise the methodological quality of the involved studies. A systematic, computerassisted literature search using Medline, CINAHL, SportDiscus and EMBASE was performed from inception to October...

Methodology for the assessment of the impact of existing high voltage lines in urban areas

Energy Technology Data Exchange (ETDEWEB)

Sumper, Andreas [Centre d' Innovacio Tecnologica en Convertidors Estatics i Accionaments (CITCEA-UPC), Departament d' Enginyeria Electrica, Universitat Politecnica de Catalunya, EU d' Enginyeria Tecnica Industrial de Barcelona, Comte d' Urgell, 187, 08036 Barcelona (Spain); Catalonia Institute for Energy Research (IREC) (Spain); Boix-Aragones, Oriol; Bergas-Jane, Joan [Centre d' Innovacio Tecnologica en Convertidors Estatics i Accionaments (CITCEA-UPC), Departament d' Enginyeria Electrica, Universitat Politecnica de Catalunya, ETS d' Enginyeria Industrial de Barcelona, Av. Diagonal, 647, Pl. 2. 08028 Barcelona (Spain); Villafafila-Robles, Roberto; Ramirez-Pisco, Rodrigo [Centre d' Innovacio Tecnologica en Convertidors Estatics i Accionaments (CITCEA-UPC), Departament d' Enginyeria Electrica, Universitat Politecnica de Catalunya, EU d' Enginyeria Tecnica Industrial de Barcelona, Comte d' Urgell, 187, 08036 Barcelona (Spain)

2010-10-15

This paper presents a methodology for the assessment of the impact of existing high voltage lines in urban areas. This methodology is based on the numeric evaluation of several impacts which are combined with weight factors. The novelty is that it opens up the possibility of citizen participation, basically in the way in which impacts and weighting factors are determined. The proposed methodology has been applied first in the municipality of Rubi, a mid-sized town near Barcelona, and later on in several municipalities in the Catalonia region in Spain. The results were used to prioritise mitigation action in the Catalonia Energy Plan. (author)

Tanzania : Country Procurement Assessment Report

OpenAIRE

World Bank

2003-01-01

This Country Procurement Assessment Report (CPAR)intends to determine the compatibility of national procurement law, and practices, with the principles of economy, and with international procurement practices. This CPAR, the second of its kind in Tanzania, looks at the legislative framework, the performance of regulatory functions, the enforcement regime, and the capacity of public sector ...

Intergrated plant safety assessment. Systematic evaluation program. Palisades plant, Consumers Power Company, Docket No. 50-255. Final report

International Nuclear Information System (INIS)

1982-10-01

The Nuclear Regulatory Commission (NRC) has published its Final Integrated Plant Safety Assessment Report (IPSAR) (NUREG-0820), under the scope of the Systematic Evaluation Program (SEP), for Consumers Power Company's Palisades Plant located in Covert, Van Buren County, Michigan. The SEP was initiated by the NRC to review the design of older operating nuclear reactor plants to reconfirm and document their safety. This report documents the review completed under the SEP for the Palisades Plant. The review has provided for (1) as assessment of the significance of differences between current technical positions on selected safety issues and those that existed when the Palisades Plant was licensed, (2) a basis for deciding on how these differences should be resolved in an integrated plant review, and (3) a documented evaluation of plant safety when all supplements to the Final IPSAR and the Safety Evaluation Report for converting the license from a provisional to a full-term license have been issued. The report also addresses the comments and recommendations made by the Advisory Committee on Reactor Safeguards in connection with its review of the Draft Report, issued in April 1982

Engineering Options Assessment Report. Nitrate Salt Waste Stream Processing

Energy Technology Data Exchange (ETDEWEB)

Anast, Kurt Roy [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2015-11-13

This report examines and assesses the available systems and facilities considered for carrying out remediation activities on remediated nitrate salt (RNS) and unremediated nitrate salt (UNS) waste containers at Los Alamos National Laboratory (LANL). The assessment includes a review of the waste streams consisting of 60 RNS, 29 above-ground UNS, and 79 candidate below-ground UNS containers that may need remediation. The waste stream characteristics were examined along with the proposed treatment options identified in the Options Assessment Report . Two primary approaches were identified in the five candidate treatment options discussed in the Options Assessment Report: zeolite blending and cementation. Systems that could be used at LANL were examined for housing processing operations to remediate the RNS and UNS containers and for their viability to provide repackaging support for remaining LANL legacy waste.

Engineering Options Assessment Report: Nitrate Salt Waste Stream Processing

Energy Technology Data Exchange (ETDEWEB)

Anast, Kurt Roy [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2015-11-18

This report examines and assesses the available systems and facilities considered for carrying out remediation activities on remediated nitrate salt (RNS) and unremediated nitrate salt (UNS) waste containers at Los Alamos National Laboratory (LANL). The assessment includes a review of the waste streams consisting of 60 RNS, 29 aboveground UNS, and 79 candidate belowground UNS containers that may need remediation. The waste stream characteristics were examined along with the proposed treatment options identified in the Options Assessment Report . Two primary approaches were identified in the five candidate treatment options discussed in the Options Assessment Report: zeolite blending and cementation. Systems that could be used at LANL were examined for housing processing operations to remediate the RNS and UNS containers and for their viability to provide repackaging support for remaining LANL legacy waste.

Patient-Reported Measures of Narcolepsy: The Need for Better Assessment.

Science.gov (United States)

Kallweit, Ulf; Schmidt, Markus; Bassetti, Claudio L

2017-05-15

Narcolepsy, a chronic disorder of the central nervous system, is clinically characterized by a symptom pentad that includes excessive daytime sleepiness, cataplexy, sleep paralysis, hypnopompic/hypnagogic hallucinations, and disrupted nighttime sleep. Ideally, screening and diagnosis instruments that assist physicians in evaluating a patient for type 1 or type 2 narcolepsy would be brief, easy for patients to understand and physicians to score, and would identify or rule out the need for electrophysiological testing. A search of the literature was conducted to review patient-reported measures used for the assessment of narcolepsy, mainly in clinical trials, with the goal of summarizing existing scales and identifying areas that may require additional screening questions and clinical practice scales. Of the seven scales reviewed, the Epworth Sleepiness Scale continues to be an important outcome measure to screen adults for excessive daytime sleepiness, which may be associated with narcolepsy. Several narcolepsy-specific scales have demonstrated utility, such as the Ullanlinna Narcolepsy Scale, Swiss Narcolepsy Scale, and Narcolepsy Symptom Assessment Questionnaire, but further validation is required. Although the narcolepsy-specific scales currently in use may identify type 1 narcolepsy, there are no validated questionnaires to identify type 2 narcolepsy. Thus, there remains a need for short, easily understood, and well-validated instruments that can be readily used in clinical practice to distinguish narcolepsy subtypes, as well as other hypersomnias, and for assessing symptoms of these conditions during treatment. © 2017 American Academy of Sleep Medicine

Comment Response on the Final Report: Peer Review of the Total System Performance Assessment-Viability Assessment (TSPA-VA)

International Nuclear Information System (INIS)

Pendleton, M. W.

1999-01-01

The Management and Operating Contractor established a Performance Assessment Peer Review Panel (hereinafter ''the Panel'') at the request of the U.S. Department of Energy Yucca Mountain Site Characterization Office. The objectives of the peer review were to provide: (1) A formal, independent evaluation and critique of Viability Assessment of a Repository at Yucca Mountain: Total System Performance Assessment, Volume 3 (DOE 1998a; hereinafter ''Total System Performance Assessment-Viability Assessment'') that was conducted in support of the Viability Assessment of a Repository at Yucca Mountain (DOE 1998b). (2) Suggestions for improvements as the U.S. Department of Energy prepares to develop the documentation for a Total System Performance Assessment to support a potential License Application. The Panel conducted a phased review over a two-year period to observe the development and, ultimately, to review the Total System Performance Assessment-Viability Assessment (DOE 1998a). During the development of the Total System Performance Assessment-Viability Assessment (DOE 1998a), the Panel submitted three Interim Reports (Whipple et al., 1997a, 1997b, and 1998) to the Management and Operating Contractor with recommendations and comments on the process models, model abstractions, and draft documentation for the Total System Performance Assessment-Viability Assessment (DOE 1998a). The Panel's Final Report Total System Performance Assessment Peer Review Panel (Whipple et al. 1999; hereinafter ''Final Report'') on the Total System Performance Assessment-Viability Assessment (DOE 1998a) is based primarily on the completed Total System Performance Assessment-Viability Assessment (DOE 1998a), the Total System Performance Assessment-Viability Assessment (TSPA-VA) Analyses Technical Basis Document (CRWMS M and O 1998), and the cited references. The Final Report (Whipple et al. 1999) includes the major points from the three Interim Reports (Whipple et al. 1997a, 1997b, and 1998

Uzbekistan : Country Procurement Assessment Report

OpenAIRE

World Bank

2003-01-01

Uzbekistan inherited the Soviet system for the procurement of goods, works and services for State needs. This system was suitable for a command economy but lacks the essential elements of competitiveness, transparency and accountability, which are the hallmarks of a market-based approach to government contracting. This Country Procurement Assessment Report (CPAR) comes at a time when a num...

Technical and economic assessment of solar hybrid repowering. Final report

Energy Technology Data Exchange (ETDEWEB)

None

1978-09-01

Public Service Company of New Mexico (PNM) has performed a Technical and Economic Assessment of Solar Hybrid Repowering under funding by the Department of Energy (DOE), the Electric Power Research Institute (EPRI), Western Energy Supply and Transmission (WEST) Associates, and a number of southwestern utilities. Solar hybrid repowering involves placement of solar hardware adjacent to and connected to existing gas- and oil-fueled electric generation units to displace some of or all the fossil fuel normally used during daylight hours. The subject study assesses the technical economic viability of the solar hybrid repowering concept within the southwestern United States and the PNM system. This document is a final report on the study and its results. The study was divided into the six primary tasks to allow a systematic investigation of the concept: (1) market survey and cost/benefit analysis, (2) study unit selection, (3) conceptual design and cost estimates, (4) unit economic analysis, (5) program planning, future phases, and (6) program management. Reeves Station No. 2 at Albuquerque, New Mexico, was selected for repowering with a design goal of 50 percent (25 MWe). The solar system design is based on the 10 MW solar central receiver pilot plant preliminary design for Barstow, California. SAN--1608-4-2 contains the technical drawings. (WHK)

Comparative Assessment of Thermal Performance of Existing Roof System and Retrofitted Green Roof System in Istanbul, Turkey

Directory of Open Access Journals (Sweden)

Nil TÜRKERİ

2011-01-01

Full Text Available Urban heat islands, temperature increase due to climate change and energy consumption due to high summer cooling load are significant issues in Turkey. International studies indicate that the green roof system serves as an energy efficient building technology. However, the thermal performance of green roofs when exposed to local climate conditions is still unknown in Turkey. A research project is being conducted at Istanbul Technical University, in which part of a low-slope existing roof system was retrofitted as an extensive green roof system and the thermal performances of both the existing roof and green roof were monitored in order to make a comparative assessment. Both the green roof and the existing roof were instrumented to measure the temperature profile within the roof systems and the solar reflectance of the roof surfaces. Local meteorological variables were also measured. Results obtained from the field monitoring revealed the following data. Reflected solar radiation from the green roof surface was slightly higher than from the existing roof surface. This was likely to be due to the fact that the plants had not yet covered the entire soil surface area of the green roof. Plants reduced the amount of heat absorbed by the growing medium during daytime through shading and reduced the surface temperature of the green roof. Ceiling temperatures of rooms under the existing roof and green roof indicated that heat transfer to the room beneath the green roof was reduced as well. The green roof reduced the heat gain due to the thermal mass of the soil. This created a buffer against daily fluctuations in temperature and minimized temperature extremes.

Building on existing institutions to perpetuate knowledge of waste repositories

International Nuclear Information System (INIS)

Weitzberg, A.

1982-08-01

Purpose of this report is to examine the function of several existing institutions and to show how they could be effectively used to transmit information about waste repositories for long times into the future. Scope of this report is limited to a discussion of four institutional approaches to the dissemination and retention of information: Widely distributed maps, the marker system of the National Geodetic Survey, the archiving of documents, and one-call systems designed to protect underground utility installations from inadvertent damage by the public. Each of these approaches is discussed in an independent section that describes the background of the institutional approach, discusses methods for applying it to waste repositories, and assesses its potential value. The sole intent of this report is to present supporting data for future decisions about the kinds of communication measures that should be implemented to advise future generations about the locations and hazards of waste repositories

Geothermal resource assessment of Atlantic Canada: progress report, 1983-1984

Energy Technology Data Exchange (ETDEWEB)

Drury, M.J.

1984-11-01

The program for the assessment of the geothermal energy potential of Atlantic Canada is now in its fifth year. Most of the work - the compilation of existing data, the acquisition of new data on an opportunity basis, and the interpretation of the amassed data base - has been substantially completed. In 1982 the program entered its final phase, that of generating new data at specific targets of interest, at considerably greater cost than earlier phases. In 1983 the various earth science projects were, with the exception of a small data-compilation continuation contract, all site- or area-specific. A test hole was drilled on the campus of the University of Prince Edward Island in Charlottetown, a magnetotelluric survey was conducted across P.E.I., and hydrological studies of two small sedimentary basins were undertaken, in New Brunswick and in Nova Scotia. This report summarizes the results obtained. Some work recently completed is also briefly discussed. 7 refs., 1 fig.

Benchmark problems for radiological assessment codes. Final report

International Nuclear Information System (INIS)

Mills, M.; Vogt, D.; Mann, B.

1983-09-01

This report describes benchmark problems to test computer codes used in the radiological assessment of high-level waste repositories. The problems presented in this report will test two types of codes. The first type of code calculates the time-dependent heat generation and radionuclide inventory associated with a high-level waste package. Five problems have been specified for this code type. The second code type addressed in this report involves the calculation of radionuclide transport and dose-to-man. For these codes, a comprehensive problem and two subproblems have been designed to test the relevant capabilities of these codes for assessing a high-level waste repository setting

Progress report of Environmental Assessment Division: 1995-1997

Energy Technology Data Exchange (ETDEWEB)

Nair, P V.N.; Nambi, K S.V. [comps.; Environmental Assessment Division, Bhabha Atomic Research Centre, Mumbai (India)

1998-08-01

The research and development (R and D) activities of Environmental Assessment Division during the period 1995 - 1997 are reported in the form of individual summaries arranged under the headings: 1) Studies on Radioactivity Measurements 2) Internal Dosimetry Studies 3) Epidemiological Studies 4) Aerosol Studies 5) Pollution Monitoring Systems 6) Studies on Trace Constituents in the Environment 7) Modelling Studies 8) Radiological Safety Assessment and 9) Dating Studies. At the end of the report, list of publications including papers published in journals, papers in symposium proceedings, papers in bulletins/newsletters and reports and summaries of Ph.D. theses completed during the period are given. (author)

Interim Report on Metallic Component Margins Under High Seismic Loads. Survey of Existing Practices and Status of Benchmark Work

International Nuclear Information System (INIS)

2015-01-01

OECD/NEA/CSNI Working Group on Integrity and Ageing of Components and Structures (WGIAGE) has the main mission to advance the current understanding of those aspects relevant to ensuring the integrity of structures, systems and components under design and beyond design loads, to provide guidance in choosing the optimal ways of dealing with challenges to the integrity of operating as well as new nuclear power plants, and to make use of an integrated approach to design, safety and plant life management. The activity (CAPS) of the WGIAGE group, entitled 'Metallic Component Margins under High Seismic Loads (MECOS)', was initially proposed by the metal sub-group of WGIAGE and approved by the CSNI in June 2012 as a Fukushima activity (F-CAPS). The proposal is aimed to assess the consequences of external hazards on plant safety. The main objectives of the MECOS project were to quantify the existing margins in seismic analysis of safety class components for high seismic loads and assess the existing design practices within a benchmark activity. The first phase of MECOS work included a survey on the existing seismic regulations and design analysis methods in the member countries. The survey was conducted by means of a questionnaire and a total of 24 questions were asked. The questionnaire consists of three parts: Seismic Input, Seismic Design Basis, and Beyond Seismic Design Basis. The majority of the respondents use the Standard or Modified Shape Spectrum and only a few countries are using the Uniform Seismic Hazard Spectra (UHS) in their seismic design regulations. All of the respondents have minimum seismic demand in their national or adopted standards. The number of defined and used seismic levels for the design of mechanical components is one or two. Almost all of the respondents are using combined testing and analysis methods for seismic qualification and design. Some countries (e.g. Canada, Finland, USA, France, Japan and UK) have specific requirements for

Assessing existing drought monitoring and forecasting capacities, mitigation and adaptation practices in Africa

Science.gov (United States)

Nyabeze, W. R.; Dlamini, L.; Lahlou, O.; Imani, Y.; Alaoui, S. B.; Vermooten, J. S. A.

2012-04-01

Drought is one of the major natural hazards in many parts of the world, including Africa and some regions in Europe. Drought events have resulted in extensive damages to livelihoods, environment and economy. In 2011, a consortium consisting of 19 organisations from both Africa and Europe started a project (DEWFORA) aimed at developing a framework for the provision of early warning and response through drought impact mitigation for Africa. This framework covers the whole chain from monitoring and vulnerability assessment to forecasting, warning, response and knowledge dissemination. This paper presents the first results of the capacity assessment of drought monitoring and forecasting systems in Africa, the existing institutional frameworks and drought mitigation and adaptation practices. Its focus is particularly on the historical drought mitigation and adaptation actions identified in the North Africa - Maghreb Region (Morocco, Algeria and Tunisia) and in the Southern Africa - Limpopo Basin. This is based on an extensive review of historical drought experiences. From the 1920's to 2009, the study identified 37 drought seasons in the North African - Maghreb Region and 33 drought seasons in the Southern Africa - Limpopo Basin. Existing literature tends to capture the spatial extent of drought at national and administrative scale in great detail. This is driven by the need to map drought impacts (food shortage, communities affected) in order to inform drought relief efforts (short-term drought mitigation measures). However, the mapping of drought at catchment scale (hydrological unit), required for longer-term measures, is not well documented. At regional level, both in North Africa and Southern Africa, two organisations are involved in drought monitoring and forecasting, while at national level 22 organisations are involved in North Africa and 37 in Southern Africa. Regarding drought related mitigation actions, the inventory shows that the most common actions

Proposal of new seismic assessment and retrofit technology for existing buildings; Hyogoken nanbu jishin higai wo kyokun to shita kison kozobutsu no taishin shindan system

Energy Technology Data Exchange (ETDEWEB)

Yoshioka, K.; Takahashi, Y.; Seki, M.; Tanida, M.; Akiyama, T.; Hashimoto, Y. [Obayashi Corp., Tokyo (Japan)

1995-08-10

A devastating earthquake measuring 7.2 on the JMA (Japan Meteorological Agency) magnitude hit the southern Hyogo Prefecture on January 17, 1995. This earthquake, the worst in Japan since the Great Kanto Earthquake in 1923, brought great disaster and destruction to the Hanshin area and Awajishima Island. Most of the damage to concrete and steel structures occurred in buildings designed according to former building codes. Fewer collapses occurred in buildings designed under current building code that have more severe seismic requirements. Existing buildings should be assessed by their seismic potentiality, and retrofitted to escape damage in severe earthquakes such as the Great Hanshin Earthquake. New technology for assessing and retrofitting existing buildings was developed to improve resisting performance in response to severe earthquakes. Earthquake Load or motion exceeding current requirements can be supplied to assess and retrofit existing buildings if a client wants their buildings to exhibit much stronger seismic resistance. The retrofit technologies, such as a base isolation system for whole building, vibration control bracing system with steel damper, and base isolation floor system for computer equipments, can be applied to existing buildings. 11 refs., 9 figs., 8 tabs.

Assessment of existing local houses condition as analysis tools for shore housing improvement program in Weriagar district, Bintuni Bay

Science.gov (United States)

Firmansyah, F.; Fernando, A.; Allo, I. P. R.

2018-01-01

The housing assessment is a part of the pre-feasibility study inThe Shore Housing Improvement Program in Weriagar District, West Papua. The housing assessment was conducted to identify the physical condition of existing houses. The parameters of assessment formulated from local references, practices and also national building regulation that covers each building system components, such as building structure/frame, building floor, building cover, and building roof. This study aims to explains lessons from local practices and references, used as the formula to generate assessment parameter, elaborate with Indonesia building regulation. The result of housing assessment were used as a basis to develop the house improvement strategy, the design alternative for housing improvement and further planning recommendations. The local knowledges involved in housing improvement program expected that the local-based approach could respect to the local build culture, respect the local environment, and the most important can offer best suitable solutions for functional utility and livability.

Transportation energy scenario analysis technical report No. 1: examination of four existing scenarios. [Projections for 1985, 1995, 2010, and 2025

Energy Technology Data Exchange (ETDEWEB)

Bernard, M. J.; LaBelle, S. J.; Millar, M.; Walbridge, E. W.

1978-03-01

This project aims to provide the DOE Division of Transportation Energy Conservation (TEC) with a long-range forecasting framework in which to evaluate potential changes to the U.S. Transportation system. This initial report examines four existing, but diverse, 50-year scenarios of the future. It describes the scenarios and summarizes the changes in the major transportation system variables that would occur through the year 2025 in each scenario. Projections of variables of interest to TEC are explored, including passenger or ton miles and energy consumption. Each is reported for 1985, 1995, 2010, and 2025 under four scenarios: success, moderate economic growth, energy crisis, and transformation. The philosophy of this project is that the transportation system must support future lifestyles; by examining potential future lifestyles the required transportation system changes can be deduced. The project: (a) develops a set of scenarios that span likely futures; (b) describes the lifestyles in each scenario in order; (c) determines the characteristics of the transportation system supporting those lifestyles; (d) indicates transportation technologies and policies necessary in that system; and (e) derives the energy characteristics of that system. The implications of the four existing scenarios are examined with emphasis on current TEC electric-vehicle development. This preliminary investigation will be followed by detailed-scenario building (modifying existing scenarios or developing new ones) and generation of lifestyles and transportation system demands under each of the scenarios. This work will be reported in October 1978.

Infiltrating Ductal Carcinoma Co-Existing with Intraductal Papillary Carcinoma of Male Breast: A Rare Case Report.

Science.gov (United States)

Kumar, Mayank; Pottipati, Bhaswanth; Arakeri, Surekha U; Javalgi, Anita P

2017-06-01

Male breast carcinomas are rare tumours, accounting for less than 1% of all malignancies in men. Intracystic Papillary Carcinoma (IPC) in males is a very rare entity, representing 5-7.5% of all male breast carcinomas. It lacks the classical clinical, radiological and cytological features of malignancy and usually presents as a benign-appearing lump. We report a case of Infiltrating Ductal Carcinoma (IDC) co-existing with intracystic papillary carcinoma in a 53-year-old male who presented with lump in the right breast.

Ion exchange technology assessment report

International Nuclear Information System (INIS)

Duhn, E.F.

1992-01-01

In the execution of its charter, the SRS Ion Exchange Technology Assessment Team has determined that ion exchange (IX) technology has evolved to the point where it should now be considered as a viable alternative to the SRS reference ITP/LW/PH process. The ion exchange media available today offer the ability to design ion exchange processing systems tailored to the unique physical and chemical properties of SRS soluble HLW's. The technical assessment of IX technology and its applicability to the processing of SRS soluble HLW has demonstrated that IX is unquestionably a viable technology. A task team was chartered to evaluate the technology of ion exchange and its potential for replacing the present In-Tank Precipitation and proposed Late Wash processes to remove Cs, Sr, and Pu from soluble salt solutions at the Savannah River Site. This report documents the ion exchange technology assessment and conclusions of the task team

Study of structural reliability of existing concrete structures

Science.gov (United States)

Druķis, P.; Gaile, L.; Valtere, K.; Pakrastiņš, L.; Goremikins, V.

2017-10-01

Structural reliability of buildings has become an important issue after the collapse of a shopping center in Riga 21.11.2013, caused the death of 54 people. The reliability of a building is the practice of designing, constructing, operating, maintaining and removing buildings in ways that ensure maintained health, ward suffered injuries or death due to use of the building. Evaluation and improvement of existing buildings is becoming more and more important. For a large part of existing buildings, the design life has been reached or will be reached in the near future. The structures of these buildings need to be reassessed in order to find out whether the safety requirements are met. The safety requirements provided by the Eurocodes are a starting point for the assessment of safety. However, it would be uneconomical to require all existing buildings and structures to comply fully with these new codes and corresponding safety levels, therefore the assessment of existing buildings differs with each design situation. This case study describes the simple and practical procedure of determination of minimal reliability index β of existing concrete structures designed by different codes than Eurocodes and allows to reassess the actual reliability level of different structural elements of existing buildings under design load.

The Adaptation Gap Report - a Preliminary Assessment

DEFF Research Database (Denmark)

Alverson, Keith; Olhoff, Anne; Noble, Ian

This first Adaptation Gap report provides an equally sobering assessment of the gap between adaptation needs and reality, based on preliminary thinking on how baselines, future goals or targets, and gaps between them might be defined for climate change adaptation. The report focuses on gaps...... in developing countries in three important areas: finance, technology and knowledge....

A defence in depth approach to safety assessment of existing nuclear power plant

International Nuclear Information System (INIS)

Butcher, P.; Holloway, N.J.

1998-01-01

The safety assessment of plant built to earlier standards requires an approach to prioritisation of upgrades that is based on sound engineering and safety principles. The principles of defence in depth are universally accepted and can form the basis of a prioritisation scheme for safety issues, and hence for the upgrading required to address them. The described scheme includes criteria for acceptability and issue prioritisation that are based on the number of lines of defence and the consequences of their failure. They are thus equivalent in concept to risk criteria, but are based on deterministic principles. This scheme has been applied successfully to the RBMK plant at Ignalina in Lithuania, for which a Western-style Safety Analysis Report has recently been produced and reviewed by joint Western and Eastern teams. An extended Safety Improvement Programme (SIP2) has been developed and agreed, based on prioritisations from the defence in depth assessment. (author)

Inert Anode Report

Energy Technology Data Exchange (ETDEWEB)

none,

1999-07-01

This ASME report provides a broad assessment of open literature and patents that exist in the area of inert anodes and their related cathode systems and cell designs, technologies that are relevant for the advanced smelting of aluminum. The report also discusses the opportunities, barriers, and issues associated with these technologies from a technical, environmental, and economic viewpoint.

Assessment of geomechanical properties of intact Opalinus Clay - Expert report

International Nuclear Information System (INIS)

Amann, F.; Vogelhuber, M.

2015-11-01

This comprehensive report published by the Swiss Federal Nuclear Safety Inspectorate ENSI presents an expert report published on the assessment of the geomechanical properties of intact Opalinus Clay. This review report addresses the conceptual constitutive framework for repositories in Opalinus Clay. The author addresses the geomechanical fundamentals that are necessary in order to adequately judge experiments on intact Opalinus Clay and the interpretation of the results. The report assesses in detail the various test series on intact Opalinus Clay carried out along with the interpretations made by experts and NAGRA. Further assessments are quoted including those on sample geometries tested, effective strength properties, undrained shear strength properties and elastic properties. The results of work done by other experts are also presented and discussed. The report is completed with a list of relevant literature

Assessment of geomechanical properties of intact Opalinus Clay - Expert report

Energy Technology Data Exchange (ETDEWEB)

Amann, F. [Eidgenössische Technische Hochschule ETHZ, Zürich (Switzerland); Vogelhuber, M. [Dr. von Moos AG, Geotechnisches Büro, Zürich (Switzerland)

2015-11-15

This comprehensive report published by the Swiss Federal Nuclear Safety Inspectorate ENSI presents an expert report published on the assessment of the geomechanical properties of intact Opalinus Clay. This review report addresses the conceptual constitutive framework for repositories in Opalinus Clay. The author addresses the geomechanical fundamentals that are necessary in order to adequately judge experiments on intact Opalinus Clay and the interpretation of the results. The report assesses in detail the various test series on intact Opalinus Clay carried out along with the interpretations made by experts and NAGRA. Further assessments are quoted including those on sample geometries tested, effective strength properties, undrained shear strength properties and elastic properties. The results of work done by other experts are also presented and discussed. The report is completed with a list of relevant literature.

Online reporting and assessing new occupational health risks in SIGNAAL.

Science.gov (United States)

Lenderink, A F; Keirsbilck, S; van der Molen, H F; Godderis, L

2015-11-01

Changes in work and working conditions continuously give rise to new work-related health risks. Without sufficient knowledge of these, opportunities for prevention and intervention may be missed. To develop, implement and evaluate an online tool called SIGNAAL for reporting and assessment of new work-related health risks by occupational health physicians and experts in the Netherlands and Belgium. Development and implementation of SIGNAAL to allow both easy and sufficient detailed reporting by occupational health physicians and structured and transparent assessment by occupational health experts. A new work-related health risk is defined as a work-related disease due to specific exposure in a specific work setting not described in the literature before. The online reporting and assessment tool proved to be a feasible means of reporting possible new combinations of health problems and exposures in the work situation. Eleven of the 15 cases reported until October 2014 were fully assessed: one was an entirely new work-related disease, four were known but uncommon work-related diseases, five were known but new in the reported work situation and one was a well-known work-related disease. An online reporting system used in an occupational health setting can provide insight into new work-related health risks by creating a structured way to gather, report and assess new combinations of health problems and exposure in the workplace. © The Author 2015. Published by Oxford University Press on behalf of the Society of Occupational Medicine. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Croatia : Country Procurement Assessment Report

OpenAIRE

World Bank

2005-01-01

Based on the CPAR's analysis of the legislative framework, procurement practices, institutional capacity and the opportunity for corruption, the assessment found that the environment for conducting public procurement in Croatia is average. This report makes a series of recommendations designed to strengthen the public procurement environment of Croatia, including legislative reform, improving procurement procedures and practices, institutional reform, capacity building, and the development of...

Pro et con analysis of existing ranking and occupational risk assessment concepts for Nanomaterials

DEFF Research Database (Denmark)

Hansen, Steffen Foss; Alstrup-Jensen, Keld; Baun, Anders

2013-01-01

There is an urgent need for adaptive, transparent, easy comprehensible and communicational and yet robust scientific methods, approaches and frameworks to evaluate the potential of exposure, hazard and risk related to the production and application of nanomaterials. A number of alternatives...... and discuss various elements of the tools (input data requirements, risk evaluation and risk handling) as well as pros and cons. We find that most of the tools provide a transparent and comprehensible approach and a few include risk management and communication going well beyond what is normally considered...... in traditional risk assessment. Most of the concepts available today however, is that their input data requirements are fairly high and some of the scientific information needed in order to apply them is inconclusive at the moment or non-existing. Some of the concepts are furthermore based on purely theoretical...

12 CFR 630.5 - Accuracy of reports and assessment of internal control over financial reporting.

Science.gov (United States)

2010-01-01

... control over financial reporting. 630.5 Section 630.5 Banks and Banking FARM CREDIT ADMINISTRATION FARM... assessment of internal control over financial reporting. (1) Annual reports must include a report by the... disclose any material change(s) in the internal control over financial reporting occurring during the...

Assessment of current techniques for reduction of indoor radon concentration in existing and new houses in European countries

International Nuclear Information System (INIS)

Holmgren, O.; Arvela, H.

2012-03-01

Radon control technologies aim at the reduction of indoor radon concentrations in existing buildings and in new construction through remedial and preventive measures. In recent years, rising ecological awareness and rising energy costs have stimulated the development of low energy and passive houses to save energy. This report contains the analysis and assessment of current techniques and technologies used to achieve the reduction of indoor radon concentrations in existing and new houses with regard to the reduction efficiency and potential impact on energy consumption (qualitative analysis). A questionnaire was prepared and sent to all RADPAR partners in 14 different countries in order to gather national information about the current remediation and prevention techniques. Responses with variable amounts of information were obtained. Based on the questionnaire responses, the status of radon remediation and prevention in each country was assessed, in addition to the reduction efficiency and potential impact on energy consumption of the current remediation and prevention techniques. The number of dwellings with an elevated indoor radon concentration typically ranges from tens of thousands to a million. The percentage of these houses already remediated varies from zero to 15%. Preventive measures in new construction have been taken from a small number of houses to over half a million houses. The research data on the current situation, the number of houses with preventive measures and the efficiency of these measures is currently still quite inadequate. Assessment of the techniques and also the surveys aiming at exploring the impact of remedial and preventive measures is greatly needed in order to promote the work at the national level. The most efficient remediation method is the active sub-slab depressurization (SSD) and the radon well, for which the reduction in the radon concentration is typically 70 - 95%. Other methods, such as sealing entry routes and improving

Power performance assessment. Final report

International Nuclear Information System (INIS)

Frandsen, S.

1998-12-01

In the increasingly commercialised wind power marketplace, the lack of precise assessment methods for the output of an investment is becoming a barrier for wider penetration of wind power. Thus, addressing this problem, the overall objectives of the project are to reduce the financial risk in investment in wind power projects by significantly improving the power performance assessment methods. Ultimately, if this objective is successfully met, the project may also result in improved tuning of the individual wind turbines and in optimisation methods for wind farm operation. The immediate, measurable objectives of the project are: To prepare a review of existing contractual aspects of power performance verification procedures of wind farms; to provide information on production sensitivity to specific terrain characteristics and wind turbine parameters by analyses of a larger number of wind farm power performance data available to the proposers; to improve the understanding of the physical parameters connected to power performance in complex environment by comparing real-life wind farm power performance data with 3D computational flow models and 3D-turbulence wind turbine models; to develop the statistical framework including uncertainty analysis for power performance assessment in complex environments; and to propose one or more procedures for power performance evaluation of wind power plants in complex environments to be applied in contractual agreements between purchasers and manufacturers on production warranties. Although the focus in this project is on power performance assessment the possible results will also be of benefit to energy yield forecasting, since the two tasks are strongly related. (au) JOULE III. 66 refs.; In Co-operation Renewable Energy System Ltd. (GB); Centre for Renewable Energy (GR); Aeronautic Research Centre (SE); National Engineering Lab. (GB); Public Power Cooperation (GR)

12 CFR 620.3 - Accuracy of reports and assessment of internal control over financial reporting.

Science.gov (United States)

2010-01-01

... control over financial reporting. 620.3 Section 620.3 Banks and Banking FARM CREDIT ADMINISTRATION FARM... control over financial reporting. (a) Prohibition against incomplete, inaccurate, or misleading... assessment of internal control over financial reporting. Annual reports of those institutions with over $1...

Assessment report for Hanford analytical services quality assurance plan

International Nuclear Information System (INIS)

Taylor, L.H.

1994-11-01

This report documents the assessment results of DOE/RL-94-55, Hanford Analytical Services Quality Assurance Plan. The assessment was conducted using the Requirement and Self-Assessment Database (RSAD), which contains mandatory and nonmandatory DOE Order statements for the relevant DOE orders

A regulatory view of the seismic assessment of existing nuclear structures in the United Kingdom

International Nuclear Information System (INIS)

Inkester, J.E.

2001-01-01

The paper describes the background to the seismic assessment of existing nuclear structures in the United Kingdom. Nuclear installations in this country were not designed specifically to resist earthquakes until the nineteen-seventies, although older plants were robustly constructed. The seismic capability of these older installations is now being evaluated as part of the periodic safety reviews which nuclear licensees are required to carry out. The regulatory requirements which set the framework for these studies are explained. The licensees' processes of hazard appraisal and examination of the response of the structure are briefly summarized. Regulatory views on some of the criteria used to judge the adequacy of safety are discussed. Finally the paper provides some comments on future initiatives and possible areas of development. (author)

MDEP STC self assessment report

International Nuclear Information System (INIS)

2013-01-01

A self assessment of the Multinational Design Evaluation Program was initiated in late 2011 to take stock of the MDEP program of work, what has been accomplished to date and what has yet to be accomplished, as well as assess if MDEP activities are enhancing safety of new reactor design reviews and harmonisation. Data was collected from both MDEP members (90 surveys were completed) and external stakeholders (15 organisations provided input). Input was requested in the areas of goals and achievements of the program, communications, scope, membership and participation. Feedback from MDEP members and external stakeholders was generally very positive. The respondents found MDEP to be a unique and useful forum to connect with experts from other regulators. Most respondents also believe that MDEP has been successful in achieving most of the goals set out in the terms of reference. However, there are areas that continue to be a challenge to harmonisation, such as differing regulatory practices among the member countries. The self-assessment found that the format and processes of the program are effective and there is not a desire for significant changes in the way the program is implemented. An overall theme that arose from the self-assessment is that MDEP is transitioning from a small group of regulators who co-operate internally, to a more inclusive organisation that has more interfaces and co-operative arrangements with other organisations. The observations from the internal and external stakeholders indicate that these interfaces with external organisations should be expanded to make MDEP more effective. For example, the conclusions suggest that MDEP is very effective in encouraging co-operation and harmonisation among the standards development organisation, and provides useful input to IAEA standard development. The self-assessment identified several actions to improve communications, and make MDEP activities more effective including: - Develop an agreed upon

Report on Integration of Existing Grid Models for N-R HES Interaction Focused on Balancing Authorities for Sub-hour Penalties and Opportunities

International Nuclear Information System (INIS)

McJunkin, Timothy; Epiney, Aaron; Rabiti, Cristian

2017-01-01

This report provides a summary of the effort in the Nuclear-Renewable Hybrid Energy System (N-R HES) project on the level 4 milestone to consider integration of existing grid models into the factors for optimization on shorter time intervals than the existing electric grid models with the Risk Analysis Virtual Environment (RAVEN) and Modelica [1] optimizations and economic analysis that are the focus of the project to date.

Report on Integration of Existing Grid Models for N-R HES Interaction Focused on Balancing Authorities for Sub-hour Penalties and Opportunities

Energy Technology Data Exchange (ETDEWEB)

McJunkin, Timothy [Idaho National Lab. (INL), Idaho Falls, ID (United States); Epiney, Aaron [Idaho National Lab. (INL), Idaho Falls, ID (United States); Rabiti, Cristian [Idaho National Lab. (INL), Idaho Falls, ID (United States)

2017-06-01

This report provides a summary of the effort in the Nuclear-Renewable Hybrid Energy System (N-R HES) project on the level 4 milestone to consider integration of existing grid models into the factors for optimization on shorter time intervals than the existing electric grid models with the Risk Analysis Virtual Environment (RAVEN) and Modelica [1] optimizations and economic analysis that are the focus of the project to date.

Information on new drugs at market entry: retrospective analysis of health technology assessment reports versus regulatory reports, journal publications, and registry reports.

Science.gov (United States)

Köhler, Michael; Haag, Susanne; Biester, Katharina; Brockhaus, Anne Catharina; McGauran, Natalie; Grouven, Ulrich; Kölsch, Heike; Seay, Ulrike; Hörn, Helmut; Moritz, Gregor; Staeck, Kerstin; Wieseler, Beate

2015-02-26

When a new drug becomes available, patients and doctors require information on its benefits and harms. In 2011, Germany introduced the early benefit assessment of new drugs through the act on the reform of the market for medicinal products (AMNOG). At market entry, the pharmaceutical company responsible must submit a standardised dossier containing all available evidence of the drug's added benefit over an appropriate comparator treatment. The added benefit is mainly determined using patient relevant outcomes. The "dossier assessment" is generally performed by the Institute for Quality and Efficiency in Health Care (IQWiG) and then published online. It contains all relevant study information, including data from unpublished clinical study reports contained in the dossiers. The dossier assessment refers to the patient population for which the new drug is approved according to the summary of product characteristics. This patient population may comprise either the total populations investigated in the studies submitted to regulatory authorities in the drug approval process, or the specific subpopulations defined in the summary of product characteristics ("approved subpopulations"). To determine the information gain from AMNOG documents compared with non-AMNOG documents for methods and results of studies available at market entry of new drugs. AMNOG documents comprise dossier assessments done by IQWiG and publicly available modules of company dossiers; non-AMNOG documents comprise conventional, publicly available sources-that is, European public assessment reports, journal publications, and registry reports. The analysis focused on the approved patient populations. Retrospective analysis. All dossier assessments conducted by IQWiG between 1 January 2011 and 28 February 2013 in which the dossiers contained suitable studies allowing for a full early benefit assessment. We also considered all European public assessment reports, journal publications, and registry reports

Reviewing the quality of strategic environmental assessment reports for English spatial plan core strategies

International Nuclear Information System (INIS)

Fischer, Thomas B.

2010-01-01

This paper summarises the results of a research project from early 2008, involving the author of this paper, as well as 18 post-graduate University of Liverpool students, in which the quality of European Directive based strategic environmental assessment (SEA) reports of English spatial plan core strategies (conducted within the context of the spatial planning sustainability appraisal-SA-regime) was reviewed. The project aimed at establishing the extensiveness of emerging spatial plan related SEA practice, as well as highlighting shortcomings and problems. Overall, it was found that whilst some aspects of assessment were done well, others were not of a satisfactory quality. Shortcomings were connected particularly with the practice of listing potentially relevant baseline documents and data without distinguishing sufficiently between those that are important in terms of significant impacts and those that are not. Problems were also found to exist with the evaluation of options and impacts, the consideration of substantive aspects, such as health, as well as regarding the formulation of final recommendations and monitoring.

Developing a new ultrasonic method to assess diaphragm movement and comparing the accuracy with existing methods

DEFF Research Database (Denmark)

Helbo Skaarup, Søren; Løkke, Anders; Laursen, Christian

2017-01-01

Introduction: Diaphragm is the most important respiratory muscle. Movement can be evaluated with ultrasound. Currently two different methods are used, M-mode and B-mode. However, diaphragm movement is complex.Aim: We hypothesized that the two existing methods are imprecise as they only measure...... film clips independently to assess inter-rater variability.Results: We found a linear correlation between FVC and diaphragmatic movement. M-mode had Pearson r=0.84 (95%CI 0.76-0.89), B-mode had r=0.68 (95%CI 0.55-0.79) and Area-measurement had r=0.84 (95%CI 0.77-0.90). Inter-rater agreement was r=0...

Acoustic assessment report for Toronto Hydro Energy Services Inc. Ashbridge's Bay power generation facility

International Nuclear Information System (INIS)

Bernard, F.; Shinbin, N.

2010-04-01

This acoustic assessment report was conducted to determine the potential noise impacts of a biogas cogeneration plant that will be located on a street in a primarily industrial area of Toronto, Ontario. The facility will be comprised of seven 1.416 MW biogas-fired reciprocating engine generators and a single flare. The report presented results obtained from noise level calculations and noise modelling studies of the on-site equipment at the planned facility. The cogeneration plant will utilize biogas produced in existing digesters to generate electricity and hot water. The biogas will be produced by anaerobic digestion from municipal sewage waste at an adjacent facility. It is expected that the facility will generate 9.912 MW of electricity from the generators. Heat resulting from the biogas combustion process is recovered from engine and exhaust flue gases by heat exchangers. The facility will operate continuously. Significant noise sources at the facility include generator exhaust gas stacks; air intake points; building ventilation fans; and roof-top heat dump radiators. Sound power levels determined for each of the noise sources were based upon worst-case operating scenarios. Results of the assessment indicated that the facility is in compliance with all Ministry of the Environment (MOE) requirements. 5 refs., 10 tabs., 4 figs.

McKenzie River Subbasin Assessment, Technical Report 2000.

Energy Technology Data Exchange (ETDEWEB)

Alsea Geospatial, Inc.

2000-02-01

This document details the findings of the McKenzie River Subbasin Assessment team. The goal of the subbasin assessment is to provide an ecological assessment of the McKenzie River Floodplain, identification of conservation and restoration opportunities, and discussion of the influence of some upstream actions and processes. This Technical Report can be viewed in conjunction with the McKenzie River Subbasin Summary or as a stand-alone document. The purpose of the technical report is to detail the methodology and findings of the consulting team that the observations and recommendations in the summary document are based on. This part, Part I, provides an introduction to the subbasin and a general overview. Part II details the specific findings of the science team. Part III provides an explanation and examples of how to use the data that has been developed through this assessment to aid in prioritizing restoration activities. Part III also includes the literature cited and appendices.

Financial gap calculations for existing cogeneration 2008

International Nuclear Information System (INIS)

Hers, S.J.; Wetzels, W.; Seebregts, A.J.; Van der Welle, A.J.

2008-05-01

The Dutch SDE (abbreviation for the renewable energy incentive) subsidy scheme promotes the reduction of CO2 emissions which results from the use of Combined Heat and Power (CHP) plants. This report calculates the profitability of operation of existing CHP plants. This information can be used for decision making on the SDE subsidy for existing CHP plants in 2008 [nl

Interim data report for the safety assessment SR-Can

International Nuclear Information System (INIS)

Vahlund, Fredrik; Andersson, Johan

2004-08-01

This document is the interim data report in the project SR-Can. The purpose of the data report is to present input data, with uncertainty estimates, for the SR-Can assessment calculations. Besides input data, the report also describes the standardised procedures used when deriving the input data and the corresponding uncertainty estimates. However, in the present interim version of the report (written in the initial stage of the project when site characterisation has yet not been completed) the standardised procedures have not been possible to apply for most of the data and, in order to present a compilation of the data used in the assessment, much of the input data is presented without following the standardised procedures. This will however be changed for the final version of the SR-Can data report, in order to show the methodology that will be used in the final version one example of how input data will be presented is included (migration data for buffer) . The recommended input data for the assessment calculations are, for the interim version, mainly based on SR 97 Beberg data, these are merely presented without any background or uncertainty discussion (this is presented in the SR 97 data report)

National environmental/energy workforce assessment. national summary. Volume Three: Nevada-South Carolina. Final report on phase 1

International Nuclear Information System (INIS)

1977-12-01

This study is one of 70 volumes assessing the workforce needs (manpower needs) for pollution control and abatement in the United States for the five-year period of 1976 through 1981. Seven fields for pollution control -- air, noise, pesticides, potable water, radiation, solid waste, and wastewater -- are analyzed, together with energy-related programs currently accentuated by the national effort to solve energy supply problems. The report identifies existing workforce levels, training programs, career opportunities, and future staffing level projections (1976 to 1982) based on the information available for the states of Nevada through South Carolina

Task force report on health effects assessment

International Nuclear Information System (INIS)

Anderson, C.; Hushon, J.

1978-08-01

From April to August, 1978 MITRE supported the Health Effects Assessment Task Force sponsored by the Office of the Assistant Secretary for the Environment at DOE. The findings of that Task Force are incorporated in this report and include a detailed definition of health effects assessment, a survey of the mandates for health effects assessments within DOE/EV, a review of current DOE-EV health effects assessment activities, an analysis of the constraints affecting the health effects assessment process and a discussion of the Task Force recommendations. Included as appendices are summaries of two workshops conducted by the Task Force to determine the state-of-the-art of health effects assessment and modeling and a review of risk assessment activities in other federal agencies. The primary recommendation of the panel was that an office be designated or created under the Office of the Assistant Secretary for the Environment to coordinate the Health Effects Risk Assessment effort covering up to 40 program and policy areas; a similar need was expressed for the environmental effects assessment area. 1 tab

McKenzie River Subbasin Assessment, Summary Report 2000.

Energy Technology Data Exchange (ETDEWEB)

Alsea Geospatial, Inc.

2000-02-01

This document summarizes the findings of the McKenzie River Subbasin Assessment: Technical Report. The subbasin assessment tells a story about the McKenzie River watershed. What is the McKenzie's ecological history, how is the McKenzie doing today, and where is the McKenzie watershed headed ecologically? Knowledge is a good foundation for action. The more we know, the better prepared we are to make decisions about the future. These decisions involve both protecting good remaining habitat and repairing some of the parts that are broken in the McKenzie River watershed. The subbasin assessment is the foundation for conservation strategy and actions. It provides a detailed ecological assessment of the lower McKenzie River and floodplain, identifies conservation and restoration opportunities, and discusses the influence of some upstream actions and processes on the study area. The assessment identifies restoration opportunities at the reach level. In this study, a reach is a river segment from 0.7 to 2.7 miles long and is defined by changes in land forms, land use, stream junctions, and/or cultural features. The assessment also provides flexible tools for setting priorities and planning projects. The goal of this summary is to clearly and concisely extract the key issues, findings, and recommendations from the full-length Technical Report. The high priority recommended action items highlight areas that the McKenzie Watershed Council can significantly influence, and that will likely yield the greatest ecological benefit. People are encouraged to read the full Technical Report if they are interested in the detailed methods, findings, and references used in this study.

Data report for the safety assessment SR-Site

International Nuclear Information System (INIS)

2010-12-01

This report compiles, documents, and qualifies input data identified as essential for the long-term safety assessment of a KBS-3 repository, and forms an important part of the reporting of the safety assessment project SR-Site. The input data concern the repository system, broadly defined as the deposited spent nuclear fuel, the engineered barriers surrounding it, the host rock, and the biosphere in the proximity of the repository. The input data also concern external influences acting on the system, in terms of climate related data. Data are provided for a selection of relevant conditions and are qualified through traceable standardised procedures

Probabilistic risk assessment (PRA) reference document. Final report

International Nuclear Information System (INIS)

Murphy, J.A.

1984-09-01

This document describes the current status of probabilistic risk assessment (PRA) as practiced in the nuclear reactor regulatory process. The PRA studies that have been completed or are under way are reviewed. The levels of maturity of the methodologies used in a PRA are discussed. Insights derived from PRAs are listed. The potential uses of PRA results for regulatory purposes are discussed. This document was issued for comment in February 1984 entitled Probabilistic Risk Assessment (PRA): Status Report and Guidance for Regulatory Application. The comments received on the draft have been considered for this final version of the report

Data report for the safety assessment SR-Site

Energy Technology Data Exchange (ETDEWEB)

2010-12-15

This report compiles, documents, and qualifies input data identified as essential for the long-term safety assessment of a KBS-3 repository, and forms an important part of the reporting of the safety assessment project SR-Site. The input data concern the repository system, broadly defined as the deposited spent nuclear fuel, the engineered barriers surrounding it, the host rock, and the biosphere in the proximity of the repository. The input data also concern external influences acting on the system, in terms of climate related data. Data are provided for a selection of relevant conditions and are qualified through traceable standardised procedures

Environmental assessment of wood domestic heating. Synthetic report

International Nuclear Information System (INIS)

2005-12-01

This report proposes a synthesis of the results of an environmental assessment of wood domestic heating. This study is based on a life cycle analysis which quantifies the impacts on the environment of all the related activities: fuel extraction, retailing, final use, and so on. Environmental impacts are assessed by means of different indicators: energetic assessment, greenhouse effect assessment, air pollution (acidification), water pollution (eutrophication), toxic material emissions in air and into the soils. Wood is compared to other heating sources (gas, fuel, electricity). Ways to improve this environmental assessment are discussed for the different types of wood (logs, pellets)

Tajikistan - Public Expenditure and Financial Accountability Assessment : Performance Report

OpenAIRE

World Bank

2007-01-01

This assessment is based on work undertaken between October 2006 and May 2007. The summary assessment covers the following three areas: an integrated assessment of PFM performance based on the 28+3 PEFA indicators, an assessment of the impact of PFM weaknesses, and the prospects for reform planning and implementation. The main report consists of four sections: an introduction, the country ...

Preliminary melter performance assessment report

International Nuclear Information System (INIS)

Elliott, M.L.; Eyler, L.L.; Mahoney, L.A.; Cooper, M.F.; Whitney, L.D.; Shafer, P.J.

1994-08-01

The Melter Performance Assessment activity, a component of the Pacific Northwest Laboratory's (PNL) Vitrification Technology Development (PVTD) effort, was designed to determine the impact of noble metals on the operational life of the reference Hanford Waste Vitrification Plant (HWVP) melter. The melter performance assessment consisted of several activities, including a literature review of all work done with noble metals in glass, gradient furnace testing to study the behavior of noble metals during the melting process, research-scale and engineering-scale melter testing to evaluate effects of noble metals on melter operation, and computer modeling that used the experimental data to predict effects of noble metals on the full-scale melter. Feed used in these tests simulated neutralized current acid waste (NCAW) feed. This report summarizes the results of the melter performance assessment and predicts the lifetime of the HWVP melter. It should be noted that this work was conducted before the recent Tri-Party Agreement changes, so the reference melter referred to here is the Defense Waste Processing Facility (DWPF) melter design

Annual Performance Reports: 2002-2003 State Assessment Data

Science.gov (United States)

Thurlow, Martha L.; Moen, Ross E.; Wiley, Hilda I.

2005-01-01

States and other educational entities receiving Part B funding under the Individuals with Disabilities Education Act (IDEA) submitted their Annual Performance Reports to the U.S. Secretary of Education on or before March 31, 2004. These reports contained information on a variety of indicators, including assessment participation and performance…

Submittal of SWMU Assessment Report for Building 9960 Surface Discharge

Energy Technology Data Exchange (ETDEWEB)

Dotson, Patrick Wells [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2015-03-01

Sandia National Laboratories is a multi-purpose engineering and science laboratory owned by the U.S. Department of Energy (DOE)/National Nuclear Security Administration and managed and operated by Sandia Corporation (Sandia), a wholly-owned subsidiary of Lockheed Martin Corporation. This Solid Waste Management Unit (SWMU) Assessment Report (SAR) for the Sandia National Laboratories, New Mexico (SNL/NM), Coyote Test Field, Building 9960 Surface Discharge, has been prepared in accordance with Section V of the Compliance Order on Consent (the Consent Order) between the New Mexico Environment Department (NMED), DOE, and Sandia (NMED April 2004). The DOE and Sandia formally notified the NMED of this newly identified or suspected SWMU or Area of Concern (AOC) by letter dated December 9, 2014. This SAR is being submitted in accordance with the NMED Hazardous Waste Bureau (HWB) letter dated February 16, 2015 letter (Kieling February 2015). This SAR presents the available information for the Building 9960 Surface Discharge, including location, designation of type and function, a general description, the operational dates, waste characteristics, and a summary of existing analytical wastewater and soil data

Resident Self-Assessment and Learning Goal Development: Evaluation of Resident-Reported Competence and Future Goals.

Science.gov (United States)

Li, Su-Ting T; Paterniti, Debora A; Tancredi, Daniel J; Burke, Ann E; Trimm, R Franklin; Guillot, Ann; Guralnick, Susan; Mahan, John D

2015-01-01

To determine incidence of learning goals by competency area and to assess which goals fall into competency areas with lower self-assessment scores. Cross-sectional analysis of existing deidentified American Academy of Pediatrics' PediaLink individualized learning plan data for the academic year 2009-2010. Residents self-assessed competencies in the 6 Accreditation Council for Graduate Medical Education (ACGME) competency areas and wrote learning goals. Textual responses for goals were mapped to 6 ACGME competency areas, future practice, or personal attributes. Adjusted mean differences and associations were estimated using multiple linear and logistic regression. A total of 2254 residents reported 6078 goals. Residents self-assessed their systems-based practice (51.8) and medical knowledge (53.0) competencies lowest and professionalism (68.9) and interpersonal and communication skills (62.2) highest. Residents were most likely to identify goals involving medical knowledge (70.5%) and patient care (50.5%) and least likely to write goals on systems-based practice (11.0%) and professionalism (6.9%). In logistic regression analysis adjusting for postgraduate year (PGY), gender, and degree type (MD/DO), resident-reported goal area showed no association with the learner's relative self-assessment score for that competency area. In the conditional logistic regression analysis, with each learner serving as his or her own control, senior residents (PGY2/3+s) who rated themselves relatively lower in a competency area were more likely to write a learning goal in that area than were PGY1s. Senior residents appear to develop better skills and/or motivation to explicitly turn self-assessed learning gaps into learning goals, suggesting that individualized learning plans may help improve self-regulated learning during residency. Copyright © 2015 Academic Pediatric Association. Published by Elsevier Inc. All rights reserved.

Fuel and canister process report for the safety assessment SR-Can

International Nuclear Information System (INIS)

Werme, Lars

2006-10-01

This report documents fuel and canister processes identified as relevant to the long-term safety of a KBS-3 repository. It forms an important part of the reporting of the safety assessment SR-Can. The detailed assessment methodology, including the role of the process report in the assessment, is described in the SR-Can Main report. The report is written by, and for, experts in the relevant scientific fields. It should though be possible for a generalist in the area of long-term safety assessments of geologic nuclear waste repositories to comprehend the contents of the report. The report is an important part of the documentation of the SR-Can project and an essential reference within the project, providing a scientifically motivated plan for the handling of geosphere processes. It is, furthermore, foreseen that the report will be essential for reviewers scrutinising the handling of geosphere issues in the SR-Can assessment. Several types of fuel will be emplaced in the repository. For the reference case with 40 years of reactor operation, the fuel quantity from boiling water reactors, BWR fuel, is estimated at 7,000 tonnes, while the quantity from pressurized water reactors, PWR fuel, is estimated at about 2,300 tonnes. In addition, 23 tonnes of mixed-oxide fuel (MOX) fuel of German origin from BWR and PWR reactors and 20 tonnes of fuel from the decommissioned heavy water reactor in Aagesta will be disposed of. To allow for future changes in the Swedish nuclear programme, the safety assessment assumes a total of 6,000 canister corresponding to 12,000 tonnes of fuel

Fuel and canister process report for the safety assessment SR-Can

Energy Technology Data Exchange (ETDEWEB)

Werme, Lars (ed.)

2006-10-15

This report documents fuel and canister processes identified as relevant to the long-term safety of a KBS-3 repository. It forms an important part of the reporting of the safety assessment SR-Can. The detailed assessment methodology, including the role of the process report in the assessment, is described in the SR-Can Main report. The report is written by, and for, experts in the relevant scientific fields. It should though be possible for a generalist in the area of long-term safety assessments of geologic nuclear waste repositories to comprehend the contents of the report. The report is an important part of the documentation of the SR-Can project and an essential reference within the project, providing a scientifically motivated plan for the handling of geosphere processes. It is, furthermore, foreseen that the report will be essential for reviewers scrutinising the handling of geosphere issues in the SR-Can assessment. Several types of fuel will be emplaced in the repository. For the reference case with 40 years of reactor operation, the fuel quantity from boiling water reactors, BWR fuel, is estimated at 7,000 tonnes, while the quantity from pressurized water reactors, PWR fuel, is estimated at about 2,300 tonnes. In addition, 23 tonnes of mixed-oxide fuel (MOX) fuel of German origin from BWR and PWR reactors and 20 tonnes of fuel from the decommissioned heavy water reactor in Aagesta will be disposed of. To allow for future changes in the Swedish nuclear programme, the safety assessment assumes a total of 6,000 canister corresponding to 12,000 tonnes of fuel.

Assessment report on research and development activities. Activity: 'Advanced science research' (Interim report)

Energy Technology Data Exchange (ETDEWEB)

NONE

2012-11-15

Japan Atomic Energy Agency (hereinafter referred to as 'JAEA') consulted an assessment committee, 'Evaluation Committee of Research Activities for Advanced Science Research' (hereinafter referred to as 'Committee') for interim assessment of 'Advanced Science Research,' in accordance with 'General Guideline for the Evaluation of Government Research and Development (R and D) Activities' by Cabinet Office, Government of Japan, 'Guideline for Evaluation of R and D in Ministry of Education, Culture, Sports, Science and Technology' and 'Regulation on Conduct for Evaluation of R and D Activities' by JAEA. In response to the JAEA's request, the Committee assessed the research programs and activities of the Advanced Science Research Center (hereinafter referred to as 'ASRC') for the period of two years from April 2010. The Committee evaluated the management and the research programs of the ASRC based on the explanatory documents prepared by the ASRC and the oral presentations with questions-and-answers by the Director and the research group leaders. This report summarizes the result of the assessment by the Committee with the Committee report attached from page 7. (author)

Actinide partitioning-transmutation program final report. I. Overall assessment

International Nuclear Information System (INIS)

Croff, A.G.; Blomeke, J.O.; Finney, B.C.

1980-06-01

This report is concerned with an overall assessment of the feasibility of and incentives for partitioning (recovering) long-lived nuclides from fuel reprocessing and fuel refabrication plant radioactive wastes and transmuting them to shorter-lived or stable nuclides by neutron irradiation. The principal class of nuclides considered is the actinides, although a brief analysis is given of the partitioning and transmutation (P-T) of 99 Tc and 129 I. The results obtained in this program permit us to make a comparison of the impacts of waste management with and without actinide recovery and transmutation. Three major conclusions concerning technical feasibility can be drawn from the assessment: (1) actinide P-T is feasible, subject to the acceptability of fuels containing recycle actinides; (2) technetium P-T is feasible if satisfactory partitioning processes can be developed and satisfactory fuels identified (no studies have been made in this area); and (3) iodine P-T is marginally feasible at best because of the low transmutation rates, the high volatility, and the corrosiveness of iodine and iodine compounds. It was concluded on the basis of a very conservative repository risk analysis that there are no safety or cost incentives for actinide P-T. In fact, if nonradiological risks are included, the short-term risks of P-T exceed the long-term benefits integrated over a period of 1 million years. Incentives for technetium and iodine P-T exist only if extremely conservative long-term risk analyses are used. Further RD and D in support of P-T is not warranted

Groundwater impact assessment report for the 284-WB Powerplant Ponds

International Nuclear Information System (INIS)

Alexander, D.J.; Johnson, V.G.; Lindsey, K.A.

1993-09-01

As required by the Hanford Federal Facility Agreement and Consent Order (Tri-Party Agreement Milestone M-17-00A), this report assesses the impact of wastewater discharged to the 284-WB Powerplant Ponds on groundwater quality. The assessment reported herein expands upon the initial analysis conducted between 1989 and 1990 for the Liquid Effluent Study Final Project Plan

Case Study Report about Gender Impact Assessment

DEFF Research Database (Denmark)

Faber, Stine Thidemann; Agustin, Lise Rolandsen

2013-01-01

The aim of this national case study report is to take a closer look at the use of Gender Impact Assessments in Denmark in order to describe the Danish implementation of this specific Gender Mainstreaming method. By way of analyzing two selected cases (two law proposals put forward by The Danish...... Ministry of Employment and the Danish Ministry of Transport, respectively) the aim is to assess the transformative potential of GIA as it is performed in Denmark....

Model summary report for the safety assessment SR-Can

Energy Technology Data Exchange (ETDEWEB)

Vahlund, Fredrik

2006-10-15

This document is the model summary report for the safety assessment SR-Can. In the report, the quality assurance measures conducted for the assessment codes are presented together with the chosen methodology. In the safety assessment SR-Can, a number of different computer codes are used. In order to better understand how these codes are related Assessment Model Flowcharts, AMFs, have been produced within the project. From these, it is possible to identify the different modelling tasks and consequently also the different computer codes used. A large number of different computer codes are used in the assessment of which some are commercial while others are developed especially for the current assessment project. QA requirements must on the one hand take this diversity into account and on the other hand be well defined. In the methodology section of the report the following requirements are defined: It must be demonstrated that the code is suitable for its purpose; It must be demonstrated that the code has been properly used; and, It must be demonstrated that the code development process has followed appropriate procedures and that the code produces accurate results. Although the requirements are identical for all codes, the measures used to show that the requirements are fulfilled will be different for different codes (for instance due to the fact that for some software the source-code is not available for review). Subsequent to the methodology section, each assessment code is presented and it is shown how the requirements are met.

Model summary report for the safety assessment SR-Can

International Nuclear Information System (INIS)

Vahlund, Fredrik

2006-10-01

This document is the model summary report for the safety assessment SR-Can. In the report, the quality assurance measures conducted for the assessment codes are presented together with the chosen methodology. In the safety assessment SR-Can, a number of different computer codes are used. In order to better understand how these codes are related Assessment Model Flowcharts, AMFs, have been produced within the project. From these, it is possible to identify the different modelling tasks and consequently also the different computer codes used. A large number of different computer codes are used in the assessment of which some are commercial while others are developed especially for the current assessment project. QA requirements must on the one hand take this diversity into account and on the other hand be well defined. In the methodology section of the report the following requirements are defined: It must be demonstrated that the code is suitable for its purpose; It must be demonstrated that the code has been properly used; and, It must be demonstrated that the code development process has followed appropriate procedures and that the code produces accurate results. Although the requirements are identical for all codes, the measures used to show that the requirements are fulfilled will be different for different codes (for instance due to the fact that for some software the source-code is not available for review). Subsequent to the methodology section, each assessment code is presented and it is shown how the requirements are met

Assessment of energy savings and of side effects associated with consumption cutoffs. Complete report + abridged version

International Nuclear Information System (INIS)

2016-03-01

As France has been the first European country to implement a legal and regulatory framework which acknowledges the role of cut-off operators, and promotes their direct participation to markets, this report aims at preparing an evolution of this framework, notably by focusing on the notion of energy saving. It highlights the importance of definitions regarding levels of consumption deferment and of energy saving associated with consumption cutoffs. The report first analyses the context: assessment of energy savings associated with consumption cutoffs, discussion of the existence or absence of a typical profile of consumption deferment, and definition of a consumption deferment rate, importance of these works for cut-off integration into the electric power system. It proposes a presentation of the present status of knowledge on energy savings and side effects, defines the energy saving rate, and discusses the sensitivity of this rate to calculation parameters. The next part presents the method adopted to analyse results obtained during experiments. The obtained results are then discussed by distinguishing those obtained in the industrial sector, in the tertiary sector, and in the residential sector. Economic studies are then reported regarding the impact of a wrong choice for the deferment rate on market mechanism rules, and the impact of an explicit taking of the deferment into account. Appendices contain detailed presentations of some specific aspects of these assessments and studies. An abridged version of the report is then provided

September 2013 Storm and Flood Assessment Report

Energy Technology Data Exchange (ETDEWEB)

Walterscheid, J. C. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2015-12-21

Between September 10 and 17, 2013, New Mexico and Colorado received a historically large amount of precipitation (Figure 1). This report assesses the damage caused by flooding along with estimated costs to repair the damage at Los Alamos National Laboratory (the Laboratory) on the Pajarito Plateau. Los Alamos County, New Mexico, received between 200% and 600% of the normal precipitation for this time period (Figure 2), and the Laboratory received approximately 450% percent of its average precipitation for September (Figure 3). As a result, the Laboratory was inundated with rain, including the extremely large, greater-than-1000-yr return period event that occurred between September 12 and 13 (Table 1). With saturated antecedent soil conditions from the September 10 storm, when the September 12 to September 13 storm hit, the flooding was disastrous to the Laboratory’s environmental infrastructure, including access roads, gage stations, watershed controls, control measures installed under the National Pollutant Discharge Elimination System Permit (hereafter, the Individual Permit), and groundwater monitoring wells (Figures 4 through 21). From September 16 to October 1, 2013, the Laboratory completed field assessments of environmental infrastructure and generated descriptions and estimates of the damage, which are presented in spreadsheets in Attachments 1 to 4 of this report. Section 2 of this report contains damage assessments by watershed, including access roads, gage stations, watershed controls, and control measures installed under the Individual Permit. Section 3 contains damage assessments of monitoring wells by the groundwater monitoring groups as established in the Interim Facility-Wide Groundwater Monitoring Plan for Monitoring Year 2014. Section 4 addresses damage and loss of automated samplers. Section 5 addresses sediment sampling needs, and Section 6 is the summary of estimated recovery costs from the significant rain and flooding during September 2013.

Department of Energy Small-Scale Hydropower Program: Feasibility assessment and technology development summary report

International Nuclear Information System (INIS)

Rinehart, B.N.

1991-06-01

This report summarizes two subprograms under the US Department of Energy's Small-Scale Hydroelectric Power Program. These subprograms were part of the financial assistance activities and included the Program Research and Development Announcement (PRDA) feasibility assessments and the technology development projects. The other major subprograms included engineering research and development, legal and institutional aspects, and technology transfer. These other subprograms are covered in their respective summary reports. The problems of energy availability and increasing costs of energy led to a national effort to develop economical and environmental attractive alternative energy resources. One such alternative involved the utilization of existing dams with hydraulic heads of <65 ft and the capacity to generate hydroelectric power of 15 MW or less. Thus, the PRDA program was initiated along with the Technology Development program. The purpose of the PRDA feasibility studies was to encourage development of renewable hydroelectric resources by providing engineering, economic, environmental, safety, and institutional information. Fifty-five feasibility studies were completed under the PRDA. This report briefly summarizes each of those projects. Many of the PRDA projects went on to become technology development projects. 56 refs., 1 fig., 2 tabs

Department of Energy Small-Scale Hydropower Program: Feasibility assessment and technology development summary report

Energy Technology Data Exchange (ETDEWEB)

Rinehart, B.N.

1991-06-01

This report summarizes two subprograms under the US Department of Energy's Small-Scale Hydroelectric Power Program. These subprograms were part of the financial assistance activities and included the Program Research and Development Announcement (PRDA) feasibility assessments and the technology development projects. The other major subprograms included engineering research and development, legal and institutional aspects, and technology transfer. These other subprograms are covered in their respective summary reports. The problems of energy availability and increasing costs of energy led to a national effort to develop economical and environmental attractive alternative energy resources. One such alternative involved the utilization of existing dams with hydraulic heads of <65 ft and the capacity to generate hydroelectric power of 15 MW or less. Thus, the PRDA program was initiated along with the Technology Development program. The purpose of the PRDA feasibility studies was to encourage development of renewable hydroelectric resources by providing engineering, economic, environmental, safety, and institutional information. Fifty-five feasibility studies were completed under the PRDA. This report briefly summarizes each of those projects. Many of the PRDA projects went on to become technology development projects. 56 refs., 1 fig., 2 tabs.

Transgender Parenting: A Review of Existing Research

OpenAIRE

Stotzer, Rebecca L; Herman, Jody L; Hasenbush, Amira

2014-01-01

The authors of this report reviewed 51 studies that analyze data about transgender parents. This report reviews the existing research on the prevalence and characteristics of transgender people who are parents, the quality of relationships between transgender parents and their children, outcomes for children with a transgender parent, and the reported needs of transgender parents. Overall, the authors found that substantial numbers of transgender people are parents, though at rates below the ...

A Modified Content Analysis of Existing School Psychology Reports

Science.gov (United States)

Mallin, Barry; Schellenberg, Miriam E.; Smith, Christiane

2012-01-01

Discrepancies between our university's training program's report-writing guidelines and common practice in Manitoba could not be resolved by reference to the literature. To inform the discussion, we collected a sample of local real world school psychology reports and undertook a modified content analysis to operationally define and measure…

Self-assessment report for fiscal year 1995. Contract 98, Appendix F

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-12-31

This report summarizes the FY 1995 self-assessment of the Lawrence Berkeley National Laboratory. The report is divided into administrative and operational support functions as set forth in the University`s contract with the Department of Energy; functional self-assessments; and independent evaluations.

The importance of building downwash in assessing the need to heighten stacks of existing small and medium sized industries

Energy Technology Data Exchange (ETDEWEB)

Gomes, J.F.P. [Centro de Tecnologias Ambientais, ISQ - Inst. de Soldadura e Qualidade, Oeiras (Portugal); Duarte, R. [Escola Superior de Tecnologia - Inst. Politecnico de Setubal (Portugal)

2004-07-01

This extended abstract intends to share the authors experience on the modelling of atmospheric pollutant dispersal and on the importance of building downwash considerations when assessing the need to heighten stacks of small and medium sized industrial enterprises (SME's). In order to understand the reasons that make industrial companies, especially SME's, consider stack heightening, in section 2 the existing Portuguese legislation on air quality and the stack heightening rules are briefly commented. New legislation that ought to appear soon (new Portuguese Air Act) is also commented and compared critically with the existing one. Then, section 3 characterizes Portuguese industry in terms of the ambient quality problems related to stack height. The adequacy of the stack heightening legislation to the particularities of the Portuguese case is discussed. In section 4 the authors experience in the specific study of stack heightening is presented. The methodology considered in these studies is discussed and compared with the application of existing and soon to appear legislation on stack height calculation. Finally, section 5 presents the conclusions and the need for an increased awareness on the pollutant dispersal problem is discussed. (orig.)

Interim main report of the safety assessment SR-Can

Energy Technology Data Exchange (ETDEWEB)

Hedin, Allan [and others

2004-08-01

This document is an interim report on the safety assessment SR-Can (SR in the acronym stands for Safety Report and Can is short for canister). The final SR-Can report will support SKB's application to build an Encapsulation plant for spent nuclear fuel and is to be produced in 2006. The purpose of the present interim report is to demonstrate the methodology for safety assessment so that it can be reviewed before it is used in a license application. The assessment relates to the KBS-3 disposal concept in which copper canisters with a cast iron insert containing spent nuclear fuel are surrounded by bentonite clay and deposited at approximately 500 m depth in saturated, granitic rock. Preliminary data from the Forsmark site, presently being investigated by SKB as one of the candidate for a KBS-3 repository are used to some extent as examples. However, the collected data are yet too sparse to allow an evaluation of safety for this site. An important aim of this report is to demonstrate the proper handling of requirements on the safety assessment in applicable regulations. Therefore, regulations issued by the Swedish Nuclear Power Inspectorate and the Swedish Radiation Protection Authority are duplicated in an Appendix. The principal acceptance criterion requires that 'the annual risk of harmful effects after closure does not exceed 10{sup -6} for a representative individual in the group exposed to the greatest risk'. 'Harmful effects' refer to cancer and hereditary effects. Following the introductory chapter 1, this report outlines the methodology for the SR-Can assessment in chapter 2, and presents in chapters 3, 4 and 5 the initial state of the system and the plans and methods for handling external influences and internal processes, respectively. Function indicators are introduced in chapter 6 and a preliminary evaluation of these is given in chapter 7. The material presented in the first seven chapters is utilised in the scenario selection in chapter 8

Interim main report of the safety assessment SR-Can

International Nuclear Information System (INIS)

Hedin, Allan

2004-08-01

This document is an interim report on the safety assessment SR-Can (SR in the acronym stands for Safety Report and Can is short for canister). The final SR-Can report will support SKB's application to build an Encapsulation plant for spent nuclear fuel and is to be produced in 2006. The purpose of the present interim report is to demonstrate the methodology for safety assessment so that it can be reviewed before it is used in a license application. The assessment relates to the KBS-3 disposal concept in which copper canisters with a cast iron insert containing spent nuclear fuel are surrounded by bentonite clay and deposited at approximately 500 m depth in saturated, granitic rock. Preliminary data from the Forsmark site, presently being investigated by SKB as one of the candidate for a KBS-3 repository are used to some extent as examples. However, the collected data are yet too sparse to allow an evaluation of safety for this site. An important aim of this report is to demonstrate the proper handling of requirements on the safety assessment in applicable regulations. Therefore, regulations issued by the Swedish Nuclear Power Inspectorate and the Swedish Radiation Protection Authority are duplicated in an Appendix. The principal acceptance criterion requires that 'the annual risk of harmful effects after closure does not exceed 10 -6 for a representative individual in the group exposed to the greatest risk'. 'Harmful effects' refer to cancer and hereditary effects. Following the introductory chapter 1, this report outlines the methodology for the SR-Can assessment in chapter 2, and presents in chapters 3, 4 and 5 the initial state of the system and the plans and methods for handling external influences and internal processes, respectively. Function indicators are introduced in chapter 6 and a preliminary evaluation of these is given in chapter 7. The material presented in the first seven chapters is utilised in the scenario selection in chapter 8. Hydrogeological

Model summary report for the safety assessment SR-Site

International Nuclear Information System (INIS)

Vahlund, Fredrik; Zetterstroem Evins, Lena; Lindgren, Maria

2010-12-01

This document is the model summary report for the safety assessment SR-Site. In the report, the quality assurance (QA) measures conducted for assessment codes are presented together with the chosen QA methodology. In the safety assessment project SR-Site, a large number of numerical models are used to analyse the system and to show compliance. In order to better understand how the different models interact and how information are transferred between the different models Assessment Model Flowcharts, AMFs, are used. From these, different modelling tasks can be identify and the computer codes used. As a large number of computer codes are used in the assessment the complexity of these differs to a large extent, some of the codes are commercial while others are developed especially for the assessment at hand. QA requirements must on the one hand take this diversity into account and on the other hand be well defined. In the methodology section of the report the following requirements are defined for all codes: - It must be demonstrated that the code is suitable for its purpose. - It must be demonstrated that the code has been properly used. - It must be demonstrated that the code development process has followed appropriate procedures and that the code produces accurate results. - It must be described how data are transferred between the different computational tasks. Although the requirements are identical for all codes in the assessment, the measures used to show that the requirements are fulfilled will be different for different types of codes (for instance due to the fact that for some software the source-code is not available for review). Subsequent to the methodology section, each assessment code is presented together with a discussion on how the requirements are met

Model summary report for the safety assessment SR-Site

Energy Technology Data Exchange (ETDEWEB)

Vahlund, Fredrik; Zetterstroem Evins, Lena (Swedish Nuclear Fuel and Waste Management Co., Stockholm (Sweden)); Lindgren, Maria (Kemakta Konsult AB, Stockholm (Sweden))

2010-12-15

This document is the model summary report for the safety assessment SR-Site. In the report, the quality assurance (QA) measures conducted for assessment codes are presented together with the chosen QA methodology. In the safety assessment project SR-Site, a large number of numerical models are used to analyse the system and to show compliance. In order to better understand how the different models interact and how information are transferred between the different models Assessment Model Flowcharts, AMFs, are used. From these, different modelling tasks can be identify and the computer codes used. As a large number of computer codes are used in the assessment the complexity of these differs to a large extent, some of the codes are commercial while others are developed especially for the assessment at hand. QA requirements must on the one hand take this diversity into account and on the other hand be well defined. In the methodology section of the report the following requirements are defined for all codes: - It must be demonstrated that the code is suitable for its purpose. - It must be demonstrated that the code has been properly used. - It must be demonstrated that the code development process has followed appropriate procedures and that the code produces accurate results. - It must be described how data are transferred between the different computational tasks. Although the requirements are identical for all codes in the assessment, the measures used to show that the requirements are fulfilled will be different for different types of codes (for instance due to the fact that for some software the source-code is not available for review). Subsequent to the methodology section, each assessment code is presented together with a discussion on how the requirements are met

Measurement properties of existing clinical assessment methods evaluating scapular positioning and function. A systematic review

DEFF Research Database (Denmark)

Larsen, Camilla Marie; Juul-Kristensen, Birgit; Lund, Hans

2014-01-01

%) to "poor" (43%), with only one study rated as "good". The reliability domain was most often investigated. Few of the assessment methods in the included studies that had "fair" or "good" measurement property ratings demonstrated acceptable results for both reliability and validity. We found a substantially...... larger number of clinical scapular assessment methods than previously reported. Using the COSMIN checklist the methodological quality of the included measurement properties in the reliability and validity domains were in general "fair" to "poor". None were examined for all three domains: (1) reliability...... excluded for evaluation due to no/few clinimetric results, leaving 35 studies for evaluation. Graded according to the COnsensus-based Standards for the selection of health Measurement INstruments (COSMIN checklist), the methodological quality in the reliability and validity domains was "fair" (57...

Assessment report on research and development activities. Activity: 'Advanced science research' (Interim report)

International Nuclear Information System (INIS)

2012-11-01

Japan Atomic Energy Agency (hereinafter referred to as “JAEA”) consulted an assessment committee, “Evaluation Committee of Research Activities for Advanced Science Research” (hereinafter referred to as “Committee”) for interim assessment of “Advanced Science Research,” in accordance with “General Guideline for the Evaluation of Government Research and Development (R and D) Activities” by Cabinet Office, Government of Japan, “Guideline for Evaluation of R and D in Ministry of Education, Culture, Sports, Science and Technology” and “Regulation on Conduct for Evaluation of R and D Activities” by JAEA. In response to the JAEA's request, the Committee assessed the research programs and activities of the Advanced Science Research Center (hereinafter referred to as “ASRC”) for the period of two years from April 2010. The Committee evaluated the management and the research programs of the ASRC based on the explanatory documents prepared by the ASRC and the oral presentations with questions-and-answers by the Director and the research group leaders. This report summarizes the result of the assessment by the Committee with the Committee report attached from page 7. (author)

Malawi : Country Procurement Assessment Report, Volume 3. Executive Summary

OpenAIRE

World Bank

2004-01-01

The Malawi Country Procurement Assessment Report is a joint undertaking between the Malawi Government and the World Bank to analyze the country procurement system and recommend appropriate actions to improve the efficiency, economy and transparency of the system. This report is divided into (a) an Executive Summary, (b) Main Report on Findings and Recommendations, and (c) Annexes. Since th...

Defense Forensic Enterprise: Assessment and Status Report Personnel Accounting Extract

Science.gov (United States)

2013-12-01

pathology , forensic anthropology, forensic toxicology, and DNA analysis to iden- tify human remains. Per DOD Directive 5205.15E, the stakeholders fall...Defense Forensic Enterprise Assessment and Status Report Personnel Accounting Extract Christine A. Hughes • Jeffrey E. Chilton John J. Clifford • C...community-related sections from a CNA report titled, “Defense Forensic Enterprise Assessment and Status Report” [1]. The first sec- tion within this

Oral Assessment in Mathematics: Implementation and Outcomes

Science.gov (United States)

Iannone, P.; Simpson, A.

2012-01-01

In this article, we report the planning and implementation of an oral assessment component in a first-year pure mathematics module of a degree course in mathematics. Our aim was to examine potential barriers to using oral assessments, explore the advantages and disadvantages compared to existing common assessment methods and document the outcomes…

Sustainability Assessment and Reporting in Agriculture Sector

Directory of Open Access Journals (Sweden)

Edward Kassem

2017-01-01

Full Text Available Sustainability assessment is a mainstream business activity that demonstrates the link between the organization’s strategy and commitment to a sustainable global economy. Sustainability indicators describe the environmental, social, economic and governance performance of Small and Medium‑sized Businesses/Enterprises (SMB/SME. Unfortunately, their implementations in the Czech Republic show a low level of engagement in sustainability assessment. The paper presents the results of the authors’ research in sustainability assessment of SMB/SMEs in the agriculture sector of the Czech Republic. An appropriate set of key performance indicators (KPIs in four dimensions (economy, environment, social and governance was developed to suit the SMB/SMEs sustainability assessment in the agriculture sector. A set of KPIs is proposed to help SMB/SMEs to avoid the barriers of sustainability assessment. These indicators are based mainly on Sustainability Assessment of Food and Agriculture, Global Reporting Initiatives Frameworks and on current research state‑of‑the‑art. They have been created following the analysis of a number of agricultural enterprises over the world, particularly within European countries.

DOE plutonium disposition study: Analysis of existing ABB-CE Light Water Reactors for the disposition of weapons-grade plutonium

International Nuclear Information System (INIS)

1994-01-01

Core reactivity and basic fuel management calculations were conducted on the selected reactors (with emphasis on the System 80 units as being the most desirable choice). Methods used were identical to those reported in the Evolutionary Reactor Report. From these calculations, the basic mission capability was assessed. The selected reactors were studied for modification, such as the addition of control rod nozzles to increase rod worth, and internals and control system modifications that might also be needed. Other system modifications studied included the use of enriched boric acid as soluble poison, and examination of the fuel pool capacities. The basic geometry and mechanical characteristics, materials and fabrication techniques of the fuel assemblies for the selected existing reactors are the same as for System 80+. There will be some differences in plutonium loading, according to the ability of the reactors to load MOX fuel. These differences are not expected to affect licensability or EPA requirements. Therefore, the fuel technology and fuel qualification sections provided in the Evolutionary Reactor Report apply to the existing reactors. An additional factor, in that the existing reactor availability presupposes the use of that reactor for the irradiation of Lead Test Assemblies, is discussed. The reactor operating and facility licenses for the operating plants were reviewed. Licensing strategies for each selected reactor were identified. The spent fuel pool for the selected reactors (Palo Verde) was reviewed for capacity and upgrade requirements. Reactor waste streams were identified and assessed in comparison to uranium fuel operations. Cost assessments and schedules for converting to plutonium disposition were estimated for some of the major modification items. Economic factors (incremental costs associated with using weapons plutonium) were listed and where possible under the scope of work, estimates were made

Technical report on design base events related to the safety assessment of a Low-level Waste Storage Facility (LWSF)

International Nuclear Information System (INIS)

Karino, Motonobu; Uryu, Mitsuru; Miyata, Kazutoshi; Matsui, Norio; Imamoto, Nobuo; Kawamata, Tatsuo; Saito, Yasuo; Nagayama, Mineo; Wakui, Yasuyuki

1999-07-01

The construction of a new Low-level Waste Storage Facility (LWSF) is planned for storage of concentrated liquid waste from existing Low-level Radioactive Waste Treatment Facility in Tokai Reprocessing Plant of JNC. An essential base for the safety designing of the facility is correctly implemented the adoption of the defence in depth principle. This report summarized criteria for judgement, selection of postulated events, major analytical conditions for anticipated operational occurrences and accidents for the safety assessment and evaluation of each event were presented. (Itami, H.)

NGNP Infrastructure Readiness Assessment: Consolidation Report

International Nuclear Information System (INIS)

Castle, Brian K.

2011-01-01

The Next Generation Nuclear Plant (NGNP) project supports the development, demonstration, and deployment of high temperature gas-cooled reactors (HTGRs). The NGNP project is being reviewed by the Nuclear Energy Advisory Council (NEAC) to provide input to the DOE, who will make a recommendation to the Secretary of Energy, whether or not to continue with Phase 2 of the NGNP project. The NEAC review will be based on, in part, the infrastructure readiness assessment, which is an assessment of industry's current ability to provide specified components for the FOAK NGNP, meet quality assurance requirements, transport components, have the necessary workforce in place, and have the necessary construction capabilities. AREVA and Westinghouse were contracted to perform independent assessments of industry's capabilities because of their experience with nuclear supply chains, which is a result of their experiences with the EPR and AP-1000 reactors. Both vendors produced infrastructure readiness assessment reports that identified key components and categorized these components into three groups based on their ability to be deployed in the FOAK plant. The NGNP project has several programs that are developing key components and capabilities. For these components, the NGNP project have provided input to properly assess the infrastructure readiness for these components.

NGNP Infrastructure Readiness Assessment: Consolidation Report

Energy Technology Data Exchange (ETDEWEB)

Brian K Castle

2011-02-01

The Next Generation Nuclear Plant (NGNP) project supports the development, demonstration, and deployment of high temperature gas-cooled reactors (HTGRs). The NGNP project is being reviewed by the Nuclear Energy Advisory Council (NEAC) to provide input to the DOE, who will make a recommendation to the Secretary of Energy, whether or not to continue with Phase 2 of the NGNP project. The NEAC review will be based on, in part, the infrastructure readiness assessment, which is an assessment of industry's current ability to provide specified components for the FOAK NGNP, meet quality assurance requirements, transport components, have the necessary workforce in place, and have the necessary construction capabilities. AREVA and Westinghouse were contracted to perform independent assessments of industry's capabilities because of their experience with nuclear supply chains, which is a result of their experiences with the EPR and AP-1000 reactors. Both vendors produced infrastructure readiness assessment reports that identified key components and categorized these components into three groups based on their ability to be deployed in the FOAK plant. The NGNP project has several programs that are developing key components and capabilities. For these components, the NGNP project have provided input to properly assess the infrastructure readiness for these components.

Factor structure of self-reported clinical disorders and personality disorders : A review of the existing literature and a factor analytical study

NARCIS (Netherlands)

Bachrach, N.; Croon, M.A.; Bekker, M.H.J.

2012-01-01

Objectives The aim of this research is to add to the current understanding of the latent factor structure of personality disorders by performing a review of the existing literature (Study 1) and a factor analytical study on the factor structure and the relationship between self-reported Axis I and

Diagnosis of district potential in terms of renewable energies. Report 1 - Present situation: Assessment of renewable energy production, Identification and quantification of territory's potentialities in terms of renewable energies

International Nuclear Information System (INIS)

2010-10-01

After a presentation of the Gers district context (geography, administrative organisation, demography, housing, economy, expertise), the report presents the energy situation, an overview of the solar thermal sector (installations and installers), of the solar photovoltaic sector (existing and projected installations, installers), of hydroelectricity, of wood-energy (individual heating, industrial heating plants, planned installations), of wind energy, of biogas, and of geothermal energy (existing and planned installations). It proposes an assessment of these energies as a whole. Then, after an overview of the district situation with respect to national objectives and to other districts of the region, the study reports an identification and quantification of potentialities in terms of theoretical resources for different energy sources (solar, wind, hydraulic, wood, methanization, valorizable biomass, geothermal, and agri-fuels). Avoided CO 2 emissions are assessed

Comparison of Parent Report and Direct Assessment of Child Skills in Toddlers.

Science.gov (United States)

Miller, Lauren E; Perkins, Kayla A; Dai, Yael G; Fein, Deborah A

2017-09-01

There are unique challenges associated with measuring development in early childhood. Two primary sources of information are used: parent report and direct assessment. Each approach has strengths and weaknesses, particularly when used to identify and diagnose developmental delays. The present study aimed to evaluate consistency between parent report and direct assessment of child skills in toddlers with and without Autism Spectrum Disorder (ASD) across receptive language, expressive language, and fine motor domains. 109 children were evaluated at an average age of two years; data on child skills were collected via parent report and direct assessment. Children were classified into three groups (i.e., ASD, Other Developmental Disorder, or Typical Development) based on DSM-IV-TR diagnosis. Mixed design ANOVAs, with data source as a within subjects factor and diagnostic group as a between subjects factor, were used to assess agreement. Chi square tests of agreement were then used to examine correspondence at the item level. Results suggested that parent report of language and fine motor skills did not significantly differ from direct assessment, and this finding held across diagnostic groups. Item level analyses revealed that, in most cases of significant disagreement, parents reported a skill as present, but it was not seen on direct testing. Results indicate that parents are generally reliable reporters of child language and fine motor abilities in toddlerhood, even when their children have developmental disorders such as ASD. However, the fullest picture may be obtained by using both parent report and direct assessment.

Final Report on Pilot Studies / Final Report on Classroom Research with STEM and TESL Assessment

DEFF Research Database (Denmark)

Biel, Carmen; Wake, Jo Dugstad; Hesse, Friedrich

This Deliverable is the final report on pilot studies within the NEXT-TELL project (D6.7) and furthermore comprises the Deliverable on Classroom Research with STEM and TESL Assessment (D2.9) in order to avoid redundancies between those two Deliverables.......This Deliverable is the final report on pilot studies within the NEXT-TELL project (D6.7) and furthermore comprises the Deliverable on Classroom Research with STEM and TESL Assessment (D2.9) in order to avoid redundancies between those two Deliverables....

Tanzania : Country Procurement Assessment Report, Volume 2. Main Report and Annexes

OpenAIRE

World Bank

2003-01-01

This Country Procurement Assessment Report (CPAR)intends to determine the compatibility of national procurement law, and practices, with the principles of economy, and with international procurement practices. This CPAR, the second of its kind in Tanzania, looks at the legislative framework, the performance of regulatory functions, the enforcement regime, and the capacity of public sector ...

Assessment of swallowability and palatability of oral dosage forms in children: Report from an M-CERSI pediatric formulation workshop.

Science.gov (United States)

Ternik, Robert; Liu, Fang; Bartlett, Jeremy A; Khong, Yuet Mei; Thiam Tan, David Cheng; Dixit, Trupti; Wang, Siri; Galella, Elizabeth A; Gao, Zhihui; Klein, Sandra

2018-02-05

The acceptability of pediatric pharmaceutical products to patients and their caregivers can have a profound impact on the resulting therapeutic outcome. However, existing methodology and approaches used for acceptability assessments for pediatric products is fragmented, making robust and consistent product evaluations difficult. A pediatric formulation development workshop took place in Washington, DC in June 2016 through the University of Maryland's Center of Excellence in Regulatory Science and Innovation (M-CERSI). A session at the workshop was dedicated to acceptability assessments and focused on two major elements that affect the overall acceptability of oral medicines, namely swallowability and palatability. The session started with presentations to provide an overview of literature, background and current state on swallowability and palatability assessments. Five parallel breakout discussions followed the presentations on each element, focusing on three overarching themes, risk-based approaches, methodology and product factors. This article reports the key outcomes of the workshop related to swallowability and palatability assessments. Copyright © 2017 Elsevier B.V. All rights reserved.

Conservation and Development Options existing on Uluguru ...

African Journals Online (AJOL)

Effective management of projects on Uluguru Mountains requires that both development and conservation options are weighed and that opportunities and challenges are considered. This study identified various conservation and development options existing on Uluguru Mountains and assessed the perceptions of the local ...

The Space Situational Assessment Report to Improve Public Awareness in China

Science.gov (United States)

Li, Hongbo; Zhang, Qi; Xie, Zebing; Wei, Xiangwang; Wang, Tao

For improvement of public awareness of the impact of space activities in China, a Space Situational Assessment Report 2013 will be issued in March 2014. More than ten Chinese main medium are invited for a special press conference. The Space Situational Assessment Report aims to introduce international space activities to Chinese public, and provide a common, comprehensive knowledge base to support the development of national policies and international security cooperation of outer space. The full report organizes international space activities until 2013 according to three parts those are Foundations, Strategies and Environment, including nine chapters, such as Space laws and policies; Space facility and equipment; Institutions and Human Resource; Military space, Civil space and Commercial space; Natural space environment; Space situational awareness, etc. A kind of Space Situational Assessment Index System is presented as a globally-focused analytic framework that defines, measures, and ranks national space activity. To use for a variety of public themes, different assessment indexes are constituted by scores of individual qualitative and quantitative metrics based on the Index System. Three research organizaitons of space sciences and technologies collaborated on the Space Situational Assessment Report. It is a scholarly and ungovernmental work.

International Code Assessment and Applications Program: Annual report

International Nuclear Information System (INIS)

Ting, P.; Hanson, R.; Jenks, R.

1987-03-01

This is the first annual report of the International Code Assessment and Applications Program (ICAP). The ICAP was organized by the Office of Nuclear Regulatory Research, United States Nuclear Regulatory Commission (USNRC) in 1985. The ICAP is an international cooperative reactor safety research program planned to continue over a period of approximately five years. To date, eleven European and Asian countries/organizations have joined the program through bilateral agreements with the USNRC. Seven proposed agreements are currently under negotiation. The primary mission of the ICAP is to provide independent assessment of the three major advanced computer codes (RELAP5, TRAC-PWR, and TRAC-BWR) developed by the USNRC. However, program activities can be expected to enhance the assessment process throughout member countries. The codes were developed to calculate the reactor plant response to transients and loss-of-coolant accidents. Accurate prediction of normal and abnormal plant response using the codes enhances procedures and regulations used for the safe operation of the plant and also provides technical basis for assessing the safety margin of future reactor plant designs. The ICAP is providing required assessment data that will contribute to quantification of the code uncertainty for each code. The first annual report is devoted to coverage of program activities and accomplishments during the period between April 1985 and March 1987

Progress report of Environmental Assessment Division 1991-1994

International Nuclear Information System (INIS)

Sadasivan, S.; Nambi, K.S.V.

1994-01-01

The research and development (R and D) activities of Environmental Assessment Division during the period 1991-1994 are reported in the form of individual summaries arranged under the headings: 1) Studies on radioactivity measurements, 2) Dosimetry, 3) Epidemiological studies, 4) Aerosol studies, 5) Pollution monitoring systems, 6) Studies on trace constituents in the environment, and 7) Modelling studies. At the end of the report a list of publications including papers published in journals, presented at symposia, conferences etc., and published technical reports is given. (author)

Progress report of Environmental Assessment Division 1991-1994

Energy Technology Data Exchange (ETDEWEB)

Sadasivan, S; Nambi, K S.V. [comps.; Bhabha Atomic Research Centre, Bombay (India). Environmental Assessment Div.

1994-12-31

The research and development (R and D) activities of Environmental Assessment Division during the period 1991-1994 are reported in the form of individual summaries arranged under the headings: (1) Studies on radioactivity measurements, (2) Dosimetry, (3) Epidemiological studies, (4) Aerosol studies, (5) Pollution monitoring systems, (6) Studies on trace constituents in the environment, and (7) Modelling studies. At the end of the report a list of publications including papers published in journals, presented at symposia, conferences etc., and published technical reports is given. (author).

Assessment report of research and development activities. Activity: 'Advanced science research' (Pre-review report)

International Nuclear Information System (INIS)

2010-11-01

Japan Atomic Energy Agency (hereinafter referred to as 'JAEA') consulted an assessment committee, 'Evaluation Committee of Research Activities for Advanced Science Research' (hereinafter referred to as 'Committee') for prior assessment of 'Advanced Science Research,' in accordance with 'General Guideline for the Evaluation of Government Research and Development (R and D) Activities' by Cabinet Office, Government of Japan, 'Guideline for Evaluation of R and D in Ministry of Education, Culture, Sports, Science and Technology' and 'Regulation on Conduct for Evaluation of R and D Activities' by JAEA. In response to the JAEA's request, the Committee assessed the research program and activities of the Advanced Science Research Center (hereinafter referred to as 'ASRC') for the period of five years from April 2010. The Committee evaluated the management and the research program of the ASRC based on the explanatory documents prepared by the ASRC and the oral presentations with questions-and-answers by the Director and the research group leaders. This report summarizes the result of the assessment by the Committee with the Committee report attached from page 7. (author)

Interim main report of the safety assessment SR-Can

Energy Technology Data Exchange (ETDEWEB)

Hedin, Allan (ed.) [and others

2004-08-01

This document is an interim report on the safety assessment SR-Can (SR in the acronym stands for Safety Report and Can is short for canister). The final SR-Can report will support SKB's application to build an Encapsulation plant for spent nuclear fuel and is to be produced in 2006. The purpose of the present interim report is to demonstrate the methodology for safety assessment so that it can be reviewed before it is used in a license application. The assessment relates to the KBS-3 disposal concept in which copper canisters with a cast iron insert containing spent nuclear fuel are surrounded by bentonite clay and deposited at approximately 500 m depth in saturated, granitic rock. Preliminary data from the Forsmark site, presently being investigated by SKB as one of the candidate for a KBS-3 repository are used to some extent as examples. However, the collected data are yet too sparse to allow an evaluation of safety for this site. An important aim of this report is to demonstrate the proper handling of requirements on the safety assessment in applicable regulations. Therefore, regulations issued by the Swedish Nuclear Power Inspectorate and the Swedish Radiation Protection Authority are duplicated in an Appendix. The principal acceptance criterion requires that 'the annual risk of harmful effects after closure does not exceed 10{sup -6} for a representative individual in the group exposed to the greatest risk'. 'Harmful effects' refer to cancer and hereditary effects. Following the introductory chapter 1, this report outlines the methodology for the SR-Can assessment in chapter 2, and presents in chapters 3, 4 and 5 the initial state of the system and the plans and methods for handling external influences and internal processes, respectively. Function indicators are introduced in chapter 6 and a preliminary evaluation of these is given in chapter 7. The material presented in the first seven chapters is utilised in the scenario selection

Structured assessment format for evaluating operative reports in general surgery.

Science.gov (United States)

Vergis, Ashley; Gillman, Lawrence; Minor, Samuel; Taylor, Mark; Park, Jason

2008-01-01

Despite its multifaceted importance, no validated or reliable tools assess the quality of the dictated operative note. This study determined the construct validity, interrater reliability, and internal consistency of a Structured Assessment Format for Evaluating Operative Reports (SAFE-OR) in general surgery. SAFE-OR was developed by using consensus criteria set forth by the Canadian Association of General Surgeons. This instrument includes a structured assessment and a global quality rating scale. Residents divided into novice and experienced groups viewed and dictated a videotaped laparoscopic sigmoid colectomy. Blinded, independent faculty evaluators graded the transcribed reports using SAFE-OR. Twenty-one residents participated in the study. Mean structured assessment scores (out of 44) were significantly lower for novice versus experienced residents (23.3 +/- 5.2 vs 34.1 +/- 6.0, t = .001). Mean global quality scores (out of 45) were similarly lower for novice residents (25.6 +/- 4.7 vs 35.9 +/- 7.6, t = .006). Interclass correlation coefficients were .98 (95% confidence interval, .96-.99) for structured assessment and .93 (95% confidence interval, .83-.97) for global quality scales. Cronbach alpha coefficients for internal consistency were .85 for structured assessment and .96 for global quality assessment scales. SAFE-OR shows significant construct validity, excellent interrater reliability, and high internal consistency. This tool will allow educators to objectively evaluate the quality of trainee operative reports and provide a mechanism for implementing, monitoring, and refining curriculum for dictation skills.

Synthesis and Comparison of Baseline Avian and Bat Use, Raptor Nesting and Mortality Information from Proposed and Existing Wind Developments: Final Report.

Energy Technology Data Exchange (ETDEWEB)

Erickson, Wallace P.

2002-12-01

Primarily due to concerns generated from observed raptor mortality at the Altamont Pass (CA) wind plant, one of the first commercial electricity generating wind plants in the U.S., new proposed wind projects both within and outside of California have received a great deal of scrutiny and environmental review. A large amount of baseline and operational monitoring data have been collected at proposed and existing U.S. wind plants. The primary use of the avian baseline data collected at wind developments has been to estimate the overall project impacts (e.g., very low, low, moderate, and high relative mortality) on birds, especially raptors and sensitive species (e.g., state and federally listed species). In a few cases, these data have also been used for guiding placement of turbines within a project boundary. This new information has strengthened our ability to accurately predict and mitigate impacts from new projects. This report should assist various stakeholders in the interpretation and use of this large information source in evaluating new projects. This report also suggests that the level of baseline data (e.g., avian use data) required to adequately assess expected impacts of some projects may be reduced. This report provides an evaluation of the ability to predict direct impacts on avian resources (primarily raptors and waterfowl/waterbirds) using less than an entire year of baseline avian use data (one season, two seasons, etc.). This evaluation is important because pre-construction wildlife surveys can be one of the most time-consuming aspects of permitting wind power projects. For baseline data, this study focuses primarily on standardized avian use data usually collected using point count survey methodology and raptor nest survey data. In addition to avian use and raptor nest survey data, other baseline data is usually collected at a proposed project to further quantify potential impacts. These surveys often include vegetation mapping and state or

Structured reporting platform improves CAD-RADS assessment.

Science.gov (United States)

Szilveszter, Bálint; Kolossváry, Márton; Karády, Júlia; Jermendy, Ádám L; Károlyi, Mihály; Panajotu, Alexisz; Bagyura, Zsolt; Vecsey-Nagy, Milán; Cury, Ricardo C; Leipsic, Jonathon A; Merkely, Béla; Maurovich-Horvat, Pál

2017-11-01

Structured reporting in cardiac imaging is strongly encouraged to improve quality through consistency. The Coronary Artery Disease - Reporting and Data System (CAD-RADS) was recently introduced to facilitate interdisciplinary communication of coronary CT angiography (CTA) results. We aimed to assess the agreement between manual and automated CAD-RADS classification using a structured reporting platform. Five readers prospectively interpreted 500 coronary CT angiographies using a structured reporting platform that automatically calculates the CAD-RADS score based on stenosis and plaque parameters manually entered by the reader. In addition, all readers manually assessed CAD-RADS blinded to the automatically derived results, which was used as the reference standard. We evaluated factors influencing reader performance including CAD-RADS training, clinical load, time of the day and level of expertise. Total agreement between manual and automated classification was 80.2%. Agreement in stenosis categories was 86.7%, whereas the agreement in modifiers was 95.8% for "N", 96.8% for "S", 95.6% for "V" and 99.4% for "G". Agreement for V improved after CAD-RADS training (p = 0.047). Time of the day and clinical load did not influence reader performance (p > 0.05 both). Less experienced readers had a higher total agreement as compared to more experienced readers (87.0% vs 78.0%, respectively; p = 0.011). Even though automated CAD-RADS classification uses data filled in by the readers, it outperforms manual classification by preventing human errors. Structured reporting platforms with automated calculation of the CAD-RADS score might improve data quality and support standardization of clinical decision making. Copyright © 2017 The Authors. Published by Elsevier Inc. All rights reserved.

Assessing Pragmatics: DCTS and Retrospective Verbal Reports

Science.gov (United States)

Beltrán-Palanques, Vicente

2016-01-01

Assessing pragmatic knowledge in the instructed setting is seen as a complex but necessary task, which requires the design of appropriate research methodologies to examine pragmatic performance. This study discusses the use of two different research methodologies, namely those of Discourse Completion Tests/Tasks (DCTs) and verbal reports. Research…

[Environmental Hazards Assessment Program annual report, June 1992--June 1993

International Nuclear Information System (INIS)

1993-01-01

The Medical University of South Carolina (MUSC) is conducting a survey of Risk Assessment and Risk Management. They are developing information on the existing level of risk associated with training and the perceived need for this training by both federal and private organizations. The purpose of the questionnaire is to determine the available training and the perception of the Risk Management process in the DOE. Of particular interest is the requirement for Risk Assessment/Management training in organizations that will be involved in the Decontamination and Decommissioning of DOE Facilities. The survey questions and instructions are included

Ontological Proofs of Existence and Non-Existence

Czech Academy of Sciences Publication Activity Database

Hájek, Petr

2008-01-01

Roč. 90, č. 2 (2008), s. 257-262 ISSN 0039-3215 R&D Projects: GA AV ČR IAA100300503 Institutional research plan: CEZ:AV0Z10300504 Keywords : ontological proofs * existence * non-existence * Gödel * Caramuel Subject RIV: BA - General Mathematics

Informative value of Patient Reported Outcomes (PRO in Health Technology Assessment (HTA

Directory of Open Access Journals (Sweden)

Brettschneider, Christian

2011-01-01

Full Text Available Background: “Patient-Reported Outcome” (PRO is used as an umbrella term for different concepts for measuring subjectively perceived health status e. g. as treatment effects. Their common characteristic is, that the appraisal of the health status is reported by the patient himself. In order to describe the informative value of PRO in Health Technology Assessment (HTA first an overview of concepts, classifications and methods of measurement is given. The overview is complemented by an empirical analysis of clinical trials and HTA-reports on rheumatoid arthritis and breast cancer in order to report on type, frequency and consequences of PRO used in these documents. Methods: For both issues systematic reviews of the literature have been performed. The search for methodological literature covers the publication period from 1990 to 2009, the search for clinical trials of rheumatoid arthritis and breast cancer covers the period 2005 to 2009. Both searches were performed in the medical databases of the German Institute of Medical Documentation and Information (DIMDI. The search for HTA-reports and methodological papers of HTA-agencies was performed in the CRD-Databases (CRD = Centre for Reviews and Dissemination and by handsearching the websites of INAHTA member agencies (INAHTA = International Network of Agencies for Health Technology Assessment. For all issues specific inclusion and exclusion criteria were defined. The methodological quality of randomized controlled trials (RCT was assessed by a modified version of the Cochrane Risk of Bias Tool. For the methodological part information extraction from the literature is structured by the report’s chapters, for the empirical part data extraction sheets were constructed. All information is summarized in a qualitative manner. Results: Concerning the methodological issues the literature search retrieved 158 documents (87 documents related to definition or classification, 125 documents related to

Improving report writing by peer assessment using Coursera

DEFF Research Database (Denmark)

Christiansen, Henrik Lehrmann

2015-01-01

report writing. In the case of report writing active learning could include peer evaluation which is what is investigated in this paper. This paper presents a case study from the Technical University of Denmark. A course on mobile communication was redesigned to include peer evaluation as a tool......Report writing is a general engineering competence and it should therefore be part of any university engineering education to learn how to write a good report. Active leaning methods are well-known to be effective in supporting student learning; hence it should preferably also be used for teaching...... for improving report writing skills. The peer evaluation process was automated using the elearning tool Coursera. What was investigated was the improvement in report writing as well as the consistency and quality of the peer assessed grades....

Existence conditions of optimal trajectories in dynamic control processes; Conditions d'existence de trajectoires optimales des processus dynamiques commandes

Energy Technology Data Exchange (ETDEWEB)

Bonnemay-Juricek, L [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1968-07-01

The existence of solutions in the optimal control problems with free endpoints is studied in this report and existence conditions are established without the usual assumption that the control region is convex. Furthermore the results, in order to be of some utility in physical applications, are expressed only by means of conditions on the parameters defining the system. (author) [French] Ce rapport etudie l'existence de solutions optimales dans les problemes de commande ou le point terminal est libre et ou la duree de l'evolution du systeme a optimiser est connue. Des conditions d'existence y sont formulees sans recourir a l'hypothese usuelle de convexite du domaine des valeurs des commandes. De plus on a cherche a rendre utilisables les resultats en ne faisant porter les conditions que sur les parametres directement accessibles du systeme. (auteur)

Screening assessment and requirements for a comprehensive assessment: Volume 1, Draft. Columbia River comprehensive impact assessment

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-04-01

To evaluate the impact to the Columbia River from the Hanford Site-derived contaminants, the U.S. Department of Energy, U.S. Environmental Protection Agency, and Washington State Department of Ecology initiated a study referred to as the Columbia River Comprehensive Impact Assessment (CRCIA). To address concerns about the scope and direction of CRCIA as well as enhance regulator, tribal, stockholder, and public involvement, the CRCIA Management Team was formed in August 1995. The Team agreed to conduct CRCIA using a phased approach. The initial phase, includes two components: 1) a screening assessment to evaluate the potential impact to the river, resulting from current levels of Hanford-derived contaminants in order to support decisions on Interim Remedial Measures, and 2) a definition of the essential work remaining to provide an acceptable comprehensive river impact assessment. The screening assessment is described in Part I of this report. The essential work remaining is Part II of this report. The objective of the screening assessment is to identify areas where the greatest potential exists for adverse effects on humans or the environment. Part I of this report discusses the scope, technical approach, and results of the screening assessment. Part II defines a new paradigm for predecisional participation by those affected by Hanford cleanup decisions.

Screening assessment and requirements for a comprehensive assessment: Volume 1, Draft. Columbia River comprehensive impact assessment

International Nuclear Information System (INIS)

1997-04-01

To evaluate the impact to the Columbia River from the Hanford Site-derived contaminants, the U.S. Department of Energy, U.S. Environmental Protection Agency, and Washington State Department of Ecology initiated a study referred to as the Columbia River Comprehensive Impact Assessment (CRCIA). To address concerns about the scope and direction of CRCIA as well as enhance regulator, tribal, stockholder, and public involvement, the CRCIA Management Team was formed in August 1995. The Team agreed to conduct CRCIA using a phased approach. The initial phase, includes two components: 1) a screening assessment to evaluate the potential impact to the river, resulting from current levels of Hanford-derived contaminants in order to support decisions on Interim Remedial Measures, and 2) a definition of the essential work remaining to provide an acceptable comprehensive river impact assessment. The screening assessment is described in Part I of this report. The essential work remaining is Part II of this report. The objective of the screening assessment is to identify areas where the greatest potential exists for adverse effects on humans or the environment. Part I of this report discusses the scope, technical approach, and results of the screening assessment. Part II defines a new paradigm for predecisional participation by those affected by Hanford cleanup decisions

Does the Kuleshov Effect really Exist?

DEFF Research Database (Denmark)

Barratt, Daniel; Cabak Rédei, Anna

2013-01-01

with a doll, a dead woman in a coffin, and a bowl of soup; the viewers of the three sequences were reported to have perceived Mozhukin’s face as expressing happiness, sadness, and hunger/thoughtfulness respectively. It is not clear, however, whether or not the socalled “Kuleshov effect” really exists...

Examiners' Reports on Theses: Feedback or Assessment?

Science.gov (United States)

Kumar, Vijay; Stracke, Elke

2011-01-01

Traditionally, examiners' reports on theses at the doctoral and Master's level consist of two components: firstly, summative assessment where a judgement is made about whether the thesis has met the standards established by the discipline for the award of the degree, and, secondly, the developmental and formative component, where examiners provide…

Letter report: Cold crucible melter assessment

International Nuclear Information System (INIS)

Elliott, M.L.

1996-03-01

One of the activities of the PNL Vitrification Technology Development (PVTD) Project is to assist the Tank Waste Remediation Systems (TWRS) Program in determining which melter systems should be performance tested for potential implementation in the high-level waste (HLW) vitrification plant. The Richland Operations Office (RL) has recommended that the Cold Crucible Melter (CCM) be evaluated as a candidate ''next generation'' melter. As a result, the CCM System Evaluation cost account was established under the PVTD Project so that the CCM could be initially assessed on a high-priority basis. This letter report summarizes a brief initial review and assessment of the CCM. Using the recommendations made in this document, Westinghouse Hanford Company (WHC) and RL will make a decision regarding the urgency of performance testing the CCM. If the decision is favorable, a subcontract will be negotiated for performance testing of a CCM using Hanford HLW simulants in a pilot-scale facility. Because of the aggressive nature of the schedule, the CCM evaluation was not rigorous. The evaluation consisted of a literature review and interviews with proponents of the technology during a recent trip to France. This letter report summarizes the evaluation and makes recommendations regarding further work in this area

Standardizing measurement, sampling and reporting for public exposure assessments

Energy Technology Data Exchange (ETDEWEB)

Rochedo, Elaine R.R. [Instituto de Radioprotecao e Dosimetria, Comissao Nacional de Energia Nuclear, Av. Salvador Allende s/No. CEP 22780-160 Rio de Janeiro, RJ (Brazil)], E-mail: elaine@ird.gov.br

2008-11-15

UNSCEAR assesses worldwide public exposure from natural and man-made sources of ionizing radiation based on information submitted to UNSCEAR by United Nations Member States and from peer reviewed scientific literature. These assessments are used as a basis for radiation protection programs of international and national regulatory and research organizations. Although UNSCEAR describes its assessment methodologies, the data are based on various monitoring approaches. In order to reduce uncertainties and improve confidence in public exposure assessments, it would be necessary to harmonize the methodologies used for sampling, measuring and reporting of environmental results.

Interfacing the existing cask fleet with the MRS

International Nuclear Information System (INIS)

Doman, J.W.; Hahn, R.E.

1992-01-01

This paper reports that the Department of Energy (DOE) is considering the possibility of using the existing fleet of casks to achieve spent fuel receipt at the Monitored Retrievable Storage (MRS) facility. The existing cask fleet includes the NLI-1/2, the NAC-LWT, the TN-8 (and TN-8L), the TN-9, and the IF-300 casks. Other casks may be available, but their status is not certain. Use of the existing cask fleet at the MRS places additional design requirements on the system, and specifically affects the cask-to-MRS interface. The decision to use the existing cask fleet also places additional demands on training needs and operator certification, and the configuration management system. Some existing cask designs may not be able to mate with a bottom opening hot cell MRS. Use of the existing cask fleet also greatly increases the number of shipments that must be received, to the point that a facility larger than originally envisioned may be required

Quality Assessment of Colonoscopy Reporting: Results from a Statewide Cancer Screening Program

Directory of Open Access Journals (Sweden)

Jun Li

2010-01-01

Full Text Available This paper aimed to assess quality of colonoscopy reports and determine if physicians in practice were already documenting recommended quality indicators, prior to the publication of a standardized Colonoscopy Reporting and Data System (CO-RADS in 2007. We examined 110 colonoscopy reports from 2005-2006 through Maryland Colorectal Cancer Screening Program. We evaluated 25 key data elements recommended by CO-RADS, including procedure indications, risk/comorbidity assessments, procedure technical descriptions, colonoscopy findings, specimen retrieval/pathology. Among 110 reports, 73% documented the bowel preparation quality and 82% documented specific cecal landmarks. For the 177 individual polyps identified, information on size and morphology was documented for 87% and 53%, respectively. Colonoscopy reporting varied considerately in the pre-CO-RADS period. The absence of key data elements may impact the ability to make recommendations for recall intervals. This paper provides baseline data to assess if CO-RADS has an impact on reporting and how best to improve the quality of reporting.

EFSA's scientific activities and achievements on the risk assessment of genetically modified organisms (GMOs) during its first decade of existence: looking back and ahead.

Science.gov (United States)

Devos, Yann; Aguilera, Jaime; Diveki, Zoltán; Gomes, Ana; Liu, Yi; Paoletti, Claudia; du Jardin, Patrick; Herman, Lieve; Perry, Joe N; Waigmann, Elisabeth

2014-02-01

Genetically modified organisms (GMOs) and derived food and feed products are subject to a risk analysis and regulatory approval before they can enter the market in the European Union (EU). In this risk analysis process, the role of the European Food Safety Authority (EFSA), which was created in 2002 in response to multiple food crises, is to independently assess and provide scientific advice to risk managers on any possible risks that the use of GMOs may pose to human and animal health and the environment. EFSA's scientific advice is elaborated by its GMO Panel with the scientific support of several working groups and EFSA's GMO Unit. This review presents EFSA's scientific activities and highlights its achievements on the risk assessment of GMOs for the first 10 years of its existence. Since 2002, EFSA has issued 69 scientific opinions on genetically modified (GM) plant market registration applications, of which 62 for import and processing for food and feed uses, six for cultivation and one for the use of pollen (as or in food), and 19 scientific opinions on applications for marketing products made with GM microorganisms. Several guidelines for the risk assessment of GM plants, GM microorganisms and GM animals, as well as on specific issues such as post-market environmental monitoring (PMEM) were elaborated. EFSA also provided scientific advice upon request of the European Commission on safeguard clause and emergency measures invoked by EU Member States, annual PMEM reports, the potential risks of new biotechnology-based plant breeding techniques, evaluations of previously assessed GMOs in the light of new scientific publications, and the use of antibiotic resistance marker genes in GM plants. Future challenges relevant to the risk assessment of GMOs are discussed. EFSA's risk assessments of GMO applications ensure that data are analysed and presented in a way that facilitates scientifically sound decisions that protect human and animal health and the environment.

Wind Resource and Feasibility Assessment Report for the Lummi Reservation

Energy Technology Data Exchange (ETDEWEB)

DNV Renewables (USA) Inc.; J.C. Brennan & Associates, Inc.; Hamer Environmental L.P.

2012-08-31

This report summarizes the wind resource on the Lummi Indian Reservation (Washington State) and presents the methodology, assumptions, and final results of the wind energy development feasibility assessment, which included an assessment of biological impacts and noise impacts.

IMPACT ASSESSMENT OF EXISTING VADOSE ZONE CONTAMINATION AT THE HANFORD SITE SX TANK FARM

International Nuclear Information System (INIS)

KHALEEL R

2007-01-01

The USDOE has initiated an impact assessment of existing vadose zone contamination at the Hanford Site SX tank farm in southeastern Washington State. The assessment followed the Resource Conservation and Recovery Act (RCRA) Corrective Action process to address the impacts of past tank waste releases to the vadose zone at the single-shell tank farm. Numerical models were developed that consider the extent of contamination presently within the vadose zone and predict contaminant movement through the vadose zone to groundwater. The transport of representative mobile (technetium-99) and immobile (cesium-137) constituents was evaluated in modeling. The model considered the accelerated movement of moisture around and beneath single-shell tanks that is attributed to bare, gravel surfaces resulting from the construction of the underground storage tanks. Infiltration, possibly nearing 100 mm yr -1 , is further amplified in the tank farm because of the umbrella effect created by percolating moisture being diverted by the impermeable, sloping surface of the large, 24-m-diameter, buried tank domes. For both the base case (no-action alternative) simulation and a simulation that considered placement of an interim surface barrier to minimize infiltration, predicted, groundwater concentrations for technetium-99 at the SX tank farm boundary were exceedingly high, on the order of 10 6 pCi L -1 . The predicted concentrations are, however, somewhat conservative because of our use of two-dimensional modeling for a three-dimensional problem. A series of simulations were performed, using recharge rates of 50, 30, and 10 mm yr -1 , and compared to the basecase(100 mm yr -1 ) results. As expected, lowering meteoric recharge delayed peak arrival times and reduced peak concentrations at the tank farm boundary

Impact Assessment of Existing Vadose Zone Contamination at the Hanford Site SX Tank Farm

International Nuclear Information System (INIS)

Khaleel, Raziuddin; White, Mark D.; Oostrom, Martinus; Wood, Marcus I.; Mann, Frederick M.; Kristofzski, John G.

2007-01-01

The USDOE has initiated an impact assessment of existing vadose zone contamination at the Hanford Site SX tank farm in southeastern Washington State. The assessment followed the Resource Conservation and Recovery Act (RCRA) Corrective Action process to address the impacts of past tank waste releases to the vadose zone at the single-shell tank farm. Numerical models were developed that consider the extent of contamination presently within the vadose zone and predict contaminant movement through the vadose zone to groundwater. The transport of representative mobile (technetium-99) and immobile (cesium-137) constituents was evaluated in modeling. The model considered the accelerated movement of moisture around and beneath single-shell tanks that is attributed to bare, gravel surfaces resulting from the construction of the underground storage tanks. Infiltration, possibly nearing 100 mm yr -1 , is further amplified in the tank farm because of the umbrella effect created by percolating moisture being diverted by the impermeable, sloping surface of the large, 24-m-diameter, buried tank domes. For both the base case (no-action alternative) simulation and a simulation that considered placement of an interim surface barrier to minimize infiltration, predicted groundwater concentrations for technetium-99 at the SX tank farm boundary were exceedingly high, on the order of 106 pCi L-1. The predicted concentrations are, however, somewhat conservative because of our use of two-dimensional modeling for a three-dimensional problem. A series of simulations were performed, using recharge rates of 50, 30, and 10 mm yr -1 , and compared to the base case (100 mm yr -1 ) results. As expected, lowering meteoric recharge delayed peak arrival times and reduced peak concentrations at the tank farm boundary.

Nuclear Nonproliferation Ontology Assessment Team Final Report

Energy Technology Data Exchange (ETDEWEB)

Strasburg, Jana D.; Hohimer, Ryan E.

2012-01-01

Final Report for the NA22 Simulations, Algorithm and Modeling (SAM) Ontology Assessment Team's efforts from FY09-FY11. The Ontology Assessment Team began in May 2009 and concluded in September 2011. During this two-year time frame, the Ontology Assessment team had two objectives: (1) Assessing the utility of knowledge representation and semantic technologies for addressing nuclear nonproliferation challenges; and (2) Developing ontological support tools that would provide a framework for integrating across the Simulation, Algorithm and Modeling (SAM) program. The SAM Program was going through a large assessment and strategic planning effort during this time and as a result, the relative importance of these two objectives changed, altering the focus of the Ontology Assessment Team. In the end, the team conducted an assessment of the state of art, created an annotated bibliography, and developed a series of ontological support tools, demonstrations and presentations. A total of more than 35 individuals from 12 different research institutions participated in the Ontology Assessment Team. These included subject matter experts in several nuclear nonproliferation-related domains as well as experts in semantic technologies. Despite the diverse backgrounds and perspectives, the Ontology Assessment team functioned very well together and aspects could serve as a model for future inter-laboratory collaborations and working groups. While the team encountered several challenges and learned many lessons along the way, the Ontology Assessment effort was ultimately a success that led to several multi-lab research projects and opened up a new area of scientific exploration within the Office of Nuclear Nonproliferation and Verification.

Tanzania : Country Procurement Assessment Report, Executive Summary

OpenAIRE

World Bank

2004-01-01

This Country Procurement Assessment Report (CPAR)intends to determine the compatibility of national procurement law, and practices, with the principles of economy, and with international procurement practices. This CPAR, the second of its kind in Tanzania, looks at the legislative framework, the performance of regulatory functions, the enforcement regime, and the capacity of public sector ...

QUALITY OF HEALTH TECHNOLOGY ASSESSMENT REPORTS PREPARED FOR THE MEDICAL SERVICES ADVISORY COMMITTEE.

Science.gov (United States)

Hua, Martin; Boonstra, Tristan; Kelly, Patrick J; Wilson, Andrew; Craig, Jonathan C; Webster, Angela C

2016-01-01

The Medical Services Advisory Committee (MSAC) makes recommendations to the Australian Government for funding health technologies under the Medicare Benefits Schedule (MBS). Differences in public, clinical, commercial, and political opinions on health expenditure emphasize the importance of defensible funding decisions. We aimed to evaluate the quality of health technology assessment (HTA) reports over time and among health technologies assessed for MSAC. A cohort study was performed of HTA reports prepared for MSAC between 1998 and 2013. We measured the quality of HTA reports using reporting guidelines proposed by the European Collaboration for Assessment of Health Interventions. Individual component scores across eleven domains were calculated, and summed for an overall aggregate score. We used linear regression to investigate any change in quality over time and among the types of technologies assessed. We included 110 HTA reports. The safety (80 percent), effectiveness (84 percent), economic (74 percent), and organizational (99 percent) domains were better reported than the psychological, social, and ethical considerations (34 percent). The basic (75 percent), methodological (62 percent), background (82 percent), contextual (46 percent), status quo (54 percent), and technical information (66 percent) that framed each assessment were inconsistently reported. On average, overall quality scores increased by 2 percent (p technologies (p = 0.22). HTA reports prepared for MSAC are a key tool in allocating scarce health resources. The overall quality of these reports has improved, but the reporting of specific domains and subthemes therein could be better addressed.

The clinical assessment of impulsivity

Directory of Open Access Journals (Sweden)

Nagesh Brahmavar Pai

2018-01-01

Full Text Available The term impulsivity is often used to describe behavior that is both spontaneous and detrimental. Impulsivity is multidimensional and derives from personality, general psychopathology as well as specific mental disorders. Thus, the construct of impulsivity is important as it is associated with numerous mental disorders as well as socially deviant behaviors ranging from behaviors targeted towards others such as aggression, to behaviors targeted toward oneself, for example, self-harm and suicide. As a clinical construct impulsivity is highly predictive of poor prognosis thus further emphasizing its clinical relevance. Therefore, the need exists for impulsivity to be clinically assessed and this assessment should take place at the same time as the assessment of risk. As risk and impulsivity are interrelated and interact. Although there are existing self-report rating scales for trait-based impulsivity, a dearth exists in regards to assessment of impulsivity in clinical practice that is focused and pragmatic. Thus, a pragmatic rubric to guide the individualized assessment of impulsivity in a clinical population is proposed. The quadrants espoused will assist both with the formulation of questions and categorization of responses to determine the most appropriate interventions for the client.

Assessment of Medical Students’ Posture When Using the Existing Best-Selling Laptop Tables Using Rapid Upper Limb Assessment Method

Directory of Open Access Journals (Sweden)

mojtaba jafarvand

2017-06-01

Full Text Available Introduction and purpose: Improper posture while working is one of the most important risk factors for musculoskeletal disorders. Regarding this, the aim of this study was to assess the posture of students studying at Qazvin University of Medical Sciences when using the existing best-selling laptop tables using rapid upper limb assessment (RULA method. Methods: This analytic, cross-sectional study was conducted on 50 male and female dormitory students in 2017. The study population was selected through stratified random sampling technique. The participants’ postures in two different work stations (tables number one and two were evaluated by means of RULA method. Data analysis was performed in SPSS version 16 using the independent sample t-test and ANOVA test. Results: According to the results, 36% and 46% of the students obtained scores of 3 and 4, respectively in case of table number one. Furthermore, regarding table number two, scores 3 and 4 were recorded for 48% and 44% of the participants, respectively. Therefore, tables number one and two were found to have 82% and 92% of level two corrective measure, respectively. In addition, a significant relationship was obtained between the demographic variables and RULA score (P<0.05. Conclusion: As the findings of the present study indicated, table number one was a better case than table number two for fitting with different body structures since it allowed for the adjustment of the height and inclination of the work surface. However, corrective measures were necessary for both tables to provide the users with comfort, convenience, health, and productivity when using these laptop tables.

Waste area Grouping 2 Phase I task data report: Human health risk assessment

International Nuclear Information System (INIS)

Purucker, S.T.; Douthat, D.M.

1996-06-01

This report is one of five reports issued in 1996 that provide follow- up information to the Phase 1 Remedial Investigation (RI) Report for Waste Area Grouping (WAG) 2 at Oak Ridge National Laboratory (ORNL). The five reports address areas of concern that could cause potential human health risk and ecological risk within WAG2 at ORNL. The purpose of this report is to present a summary of the human health risk assessment results based on the data collected for the WAG 2 Phase 1 RI. Estimates of risk are provided based on measured concentrations in the surface water, floodplain soil, and sediment of White Oak Creek, Melton Branch, and their tributaries. The human health risk assessment methodology used in this risk assessment is based on Risk Assessment Guidance for Superfund (RAGS). First, the data for the different media are elevated to determine usability for risk assessment. Second, through the process of selecting chemicals of potential concern (COPCs), contaminants to be considered in the risk assessment are identified for each assessment of exposure potential is performed, and exposure pathways are identified. Subsequently, exposure is estimated quantitatively, and the toxicity of each of the COPCs is determined. The results of these analyses are combined and summarized in a risk characterization

Cape Verde Report on the Observance of Standards and Codes : Accounting and Auditing

OpenAIRE

World Bank

2012-01-01

This Report on the Observance of Standards and Codes (ROSC) provides an assessment of the strengths and weaknesses of the existing financial reporting infrastructure that underpins financial accounting and auditing practices in Cape Verde. The assessment focuses on six pillars of financial reporting infrastructure: statutory framework, professional education and training, accountancy profe...

Department of Energy, highly enriched uranium ES ampersand H vulnerability assessment, Idaho National Engineering Laboratory site assessment team report

International Nuclear Information System (INIS)

1996-01-01

In accordance with the February 22, 1996 directive issued by Secretary of Energy O'Leary on the Vulnerability Assessment of Highly Enriched Uranium (HEU) Storage, the Idaho National Engineering Laboratory conducted an assessment of the site's HEU holdings and any associated vulnerabilities. The assessment was conducted between April 25 and May 24, 1996. The scope of this assessment, as defined in the Assessment Plan, included all HEU, and any spent fuel not evaluated in the Spent Fuel Vulnerability Assessment. Addressed in this assessment were all of the holdings at the Idaho National Engineering Laboratory (INEL) except any located at Argonne National Laboratory-West (ANL-W) and the Naval Reactors Facility. Excluded from the assessment were those HEU holdings previously assessed in the Idaho National Engineering Laboratory Spent Nuclear Fuel Inventory and Vulnerability Site Assessment Report and any HEU holdings evaluated in the Plutonium Vulnerability Assessment Report

Techniques of monitoring blood glucose during pregnancy for women with pre-existing diabetes.

Science.gov (United States)

Moy, Foong Ming; Ray, Amita; Buckley, Brian S; West, Helen M

2017-06-11

Self-monitoring of blood glucose (SMBG) is recommended as a key component of the management plan for diabetes therapy during pregnancy. No existing systematic reviews consider the benefits/effectiveness of various techniques of blood glucose monitoring on maternal and infant outcomes among pregnant women with pre-existing diabetes. The effectiveness of the various monitoring techniques is unclear. To compare techniques of blood glucose monitoring and their impact on maternal and infant outcomes among pregnant women with pre-existing diabetes. We searched the Cochrane Pregnancy and Childbirth Group's Trials Register (30 November 2016), searched reference lists of retrieved studies and contacted trial authors. Randomised controlled trials (RCTs) and quasi-RCTs comparing techniques of blood glucose monitoring including SMBG, continuous glucose monitoring (CGM) or clinic monitoring among pregnant women with pre-existing diabetes mellitus (type 1 or type 2). Trials investigating timing and frequency of monitoring were also included. RCTs using a cluster-randomised design were eligible for inclusion but none were identified. Two review authors independently assessed study eligibility, extracted data and assessed the risk of bias of included studies. Data were checked for accuracy. The quality of the evidence was assessed using the GRADE approach. This review update includes at total of 10 trials (538) women (468 women with type 1 diabetes and 70 women with type 2 diabetes). The trials took place in Europe and the USA. Five of the 10 included studies were at moderate risk of bias, four studies were at low to moderate risk of bias, and one study was at high risk of bias. The trials are too small to show differences in important outcomes such as macrosomia, preterm birth, miscarriage or death of baby. Almost all the reported GRADE outcomes were assessed as being very low-quality evidence. This was due to design limitations in the studies, wide confidence intervals, small

Environmental Hazards Assessment Program. Quarterly report, July--September 1995

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-10-31

This report describes activities and reports on progress for the first quarter (July--September) of the fourth year of the grant to support the Environmental Hazards Assessment Program (EHAP) at the Medical University of South Carolina. It reports progress against the grant objectives and the Program Implementation Plan published at the end of the first year of the grant. The objectives of EHAP stated in the proposal to DOE are to: (1) develop a holistic, national basis for risk assessment, risk management, and risk communication that recognizes the direct impact of environmental hazards on the health and well-being of all; (2) develop a pool of talented scientists and experts in cleanup activities, especially in human health aspects; and (3) identify needs and develop programs addressing the critical shortage of well-educated, highly-skilled technical and scientific personnel to address the health-oriented aspects of environmental restoration and waste management.

A two-phase pressure drop calculation code based on a new method with a correlation factor obtained from an assessment of existing correlations

International Nuclear Information System (INIS)

Chun, Moon Hyun; Oh, Jae Guen

1989-01-01

Ten methods of the total two-phase pressure drop prediction based on five existing models and correlations have been examined for their accuracy and applicability to pressurized water reactor conditions. These methods were tested against 209 experimental data of local and bulk boiling conditions: Each correlations were evaluated for different ranges of pressure, mass velocity and quality, and best performing models were identified for each data subsets. A computer code entitled 'K-TWOPD' has been developed to calculate the total two phase pressure drop using the best performing existing correlations for a specific property range and a correction factor to compensate for the predicted error of the selected correlations. Assessment of this code shows that the present method fits all the available data within ±11% at a 95% confidence level compared with ± 25% for the existing correlations. (Author)

An Assessment of SKB's Performance Assessment Calculations in the Interim Main Report for the Safety Assessment SR-Can

International Nuclear Information System (INIS)

Maul, Philip; Robinson, Peter

2005-03-01

SKB have published their Interim Main Report of the safety assessment SR-Can, which is intended to establish the framework for what will be submitted in 2006 in support of a licence application for construction of the spent fuel encapsulation plant. This follows on from the SR-Can Planning Document published in 2003. The purpose of the Interim Report is stated to be to demonstrate the methodology that will be used for safety assessment. The present report evaluates the information provided in the Interim SR-Can Report that is relevant to the Performance Assessment (PA) calculations that SKB intend to undertake, using independent calculations to facilitate this process. SKB consider that the primary safety function is to isolate completely the fuel within the canisters over the entire assessment period. Should a canister be damaged, the secondary safety function is to ensure that any release is retarded and dispersed sufficiently to ensure that concentrations levels in the accessible environment cannot cause unacceptable consequences. In this report PA calculations are considered to include both a high-level representation of the evolution of the system (relevant to the primary safety function), and any subsequent radionuclide transport (relevant to the secondary safety function). The main conclusions drawn are: 1. The effects of climate evolution on engineered barriers have not been analysed in detail in the Interim Report, and this limits the usefulness of the preliminary calculations that have been undertaken. 2. A key aspect of SKB's approach is the use of an integrated near-field evolution model. The information provided on this model demonstrates its capability efficiently to reproduce calculations from individual process models, but insufficient information is given at the present time to justify statements about interactions between processes. In particular it is assumed that relatively short term thermal and resaturation processes do not affect the

Transportation capabilities of the existing cask fleet

International Nuclear Information System (INIS)

Johnson, P.E.; Wankerl, M.W.; Joy, D.S.

1991-01-01

This paper describes a number of scenarios estimating the amount of spent nuclear fuel that could be transported to a Monitored Retrievable Storage (MRS) Facility by various combinations of existing cask fleets. To develop the scenarios, the data provided by the Transportation System Data Base (TSDB) were modified to reflect the additional time for cask turnaround resulting from various startup and transportation issues. With these more realistic speed and cask-handling assumptions, the annual transportation capability of a fleet consisting of all of the existing casks is approximately 465 metric tons of uranium (MTU). The most likely fleet of existing casks that would be made available to the DOE consists of two rail, three overweight truck, and six legal weight truck casks. Under the same transportation assumptions, this cask fleet is capable of approximately transporting 270 MTU/year. These ranges of capability is a result of the assumptions pertaining to the number of casks assumed to be available. It should be noted that this assessment assumes additional casks based on existing certifications are not fabricated

Transportation capabilities of the existing cask fleet

International Nuclear Information System (INIS)

Johnson, P.E.; Joy, D.S.; Wankerl, M.W.

1991-01-01

This paper describes a number of scenarios estimating the amount of spent nuclear fuel that could be transported to a Monitored Retrievable Storage (MRS) Facility by various combinations of existing cask fleets. To develop the scenarios, the data provided by the Transportation System Data Base (TSDB) were modified to reflect the additional time for cask turnaround resulting from various startup and transportation issues. With these more realistic speed and cask-handling assumptions, the annual transportation capability of a fleet consisting of all of the existing casks is approximately 46 metric tons of uranium (MTU). The most likely fleet of existing casks that would be made available to the Department of Energy (DOE) consists of two rail, three overweight truck, and six legal weight truck casks. Under the same transportation assumptions, this cask fleet is capable of approximately transporting 270 MTU/year. These ranges of capability is a result of the assumptions pertaining to the number of casks assumed to be available. It should be noted that this assessment assumes additional casks based on existing certifications are not fabricated. 5 refs., 4 tabs

The impact of health technology assessment reports on decision making in Austria.

Science.gov (United States)

Zechmeister, Ingrid; Schumacher, Ines

2012-01-01

Health technology assessment (HTA) was established in Austria in the 1990s and, since then, it has gained considerable importance. In this study, we aim to analyze whether the HTA reports that have been produced at the Institute for Technology Assessment (ITA) and at the Ludwig Boltzmann Institute for HTA (LBI-HTA) have had an impact on decision making within the Austrian health care system. We selected all reports that were intended for supporting (i) reimbursement/investment or (ii) disinvestment decisions. Eleven full HTA reports and fifty-eight rapid assessments fulfilled the inclusion criteria. We used interview data and administrative data on volumes, tariffs and expenditure of products/services to analyze whether and how reports were in reality used in decision making and what the consequences for health care expenditure and resource distribution have been. Five full HTA reports and fifty-six rapid technology assessments were used for reimbursement decisions. Four full HTA reports and two rapid assessments were used for disinvestment decisions and resulted in reduced volumes and expenditure. Two full HTA reports showed no impact on decision making. Impact was most evident for hospital technologies. HTA has played some role in reducing volumes of over-supplied hospital technologies, resulting in reduced expenditure for several hospital providers. Additionally, it has been increasingly included in prospective planning and reimbursement decisions of late, indicating re-distribution of resources toward evidence-based technologies. However, further factors may have influenced the decisions, and the impact could be considerably increased by systematically incorporating HTA into the decision-making process in Austria.

Existence conditions of optimal trajectories in dynamic control processes; Conditions d'existence de trajectoires optimales des processus dynamiques commandes

Energy Technology Data Exchange (ETDEWEB)

Bonnemay-Juricek, L. [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1968-07-01

The existence of solutions in the optimal control problems with free endpoints is studied in this report and existence conditions are established without the usual assumption that the control region is convex. Furthermore the results, in order to be of some utility in physical applications, are expressed only by means of conditions on the parameters defining the system. (author) [French] Ce rapport etudie l'existence de solutions optimales dans les problemes de commande ou le point terminal est libre et ou la duree de l'evolution du systeme a optimiser est connue. Des conditions d'existence y sont formulees sans recourir a l'hypothese usuelle de convexite du domaine des valeurs des commandes. De plus on a cherche a rendre utilisables les resultats en ne faisant porter les conditions que sur les parametres directement accessibles du systeme. (auteur)

Environmental Risk Assessment of Genetically Modified Organisms (GMOs)

DEFF Research Database (Denmark)

Strandberg, B.; Kjær, C.; Hindar, K.

It was the aim of this NordTest project to propose improvements that prepare us to assess ecological risks to the environment associated with releases of existing and coming GMO cases. The report is separated into three sections. The first describes the frames of ecological risk assessment...

Solar potential in existing urban layouts—Critical overview of the existing building stock in Slovenian context

International Nuclear Information System (INIS)

Košir, Mitja; Capeluto, Isaac Guedi; Krainer, Aleš; Kristl, Živa

2014-01-01

In recent years implementation of sustainable building design in the EU has become one of the key issues in reducing energy dependence. In this context efficient use of solar potential incident on building envelope is essential. The goal of the study is to evaluate the influence of interventions required by the new Slovenian legislation and to propose general site planning guidelines. Special emphasis is devoted to the existing building stock, which is due for refurbishment. The study is carried out on the basis of seven typical urban layouts, which are assessed according to the shape of layout, density, building orientation and design. The calculations are carried out with the program SHADING. The study showed that the existing layouts are not as problematic as had been expected and that form and orientation of buildings present a major challenge. Nevertheless, the quality and the duration of insolation are highly dependent on the specifics of each case. The study showed that by respecting the basic rules of good practice in conjunction with the existing requirements no major changes in the existing design principles are needed. - Highlights: • New Slovenian legislation regarding minimum insolation of building envelope. • Seven typical urban layouts were analysed. • Requirements and rules of good practice result in adequate insolation. • Duration of insolation is highly dependent on the specifics of each case

Malawi : Country Procurement Assessment Report, Volume 2. Details and Annexes

OpenAIRE

World Bank

2004-01-01

The Malawi Country Procurement Assessment Report is a joint undertaking between the Malawi Government and the World Bank to analyze the country procurement system and recommend appropriate actions to improve the efficiency, economy and transparency of the system. This report is divided into (a) an Executive Summary, (b) Main Report on Findings and Recommendations, and (c) Annexes. Since th...

Finding facts for policy makers. IPCC's Special Reports and the Third Assessment Report

International Nuclear Information System (INIS)

Leemans, R.; Verbeek, K.

2000-01-01

The Intergovernmental Panel on Climate Change (IPCC) is an international body of the WMO (World Meteorological Organization) and UNEP (United Nations Environmental Programme) that publishes authoritative reports on the scientific, technical and socio-economic aspects of climate change and climate policy. The knowledge contained in the IPCC reports forms the basis for the development of global climate policy by the UN Framework Convention on Climate Change (UNFCCC). The three volumes of the Third Assessment Report will be published early in 2001, shortly after Cop6 (Sixth Convention of Parties, The Hague, Netherlands, November 2000). This broadly supported summary of scientific insights will be important for the further substantiation of climate policy

Assessing Tuition- and Debt-Free Higher Education. NASFAA Task Force Report

Science.gov (United States)

National Association of Student Financial Aid Administrators, 2017

2017-01-01

The Assessing Tuition- and Debt-Free Higher Education Task Force was convened in July 2016. Charged by the National Association of Student Financial Aid Administrators's (NASFAA's) Board of Directors with evaluating the existing landscape of state and local promise programs with a focus on scaling such models to the national level, the task force…

Trout Creek, Oregon Watershed Assessment; Findings, Condition Evaluation and Action Opportunities, 2002 Technical Report.

Energy Technology Data Exchange (ETDEWEB)

Runyon, John

2002-08-01

The purpose of the assessment is to characterize historical and current watershed conditions in the Trout Creek Watershed. Information from the assessment is used to evaluate opportunities for improvements in watershed conditions, with particular reference to improvements in the aquatic environment. Existing information was used, to the extent practicable, to complete this work. The assessment will aid the Trout Creek Watershed Council in identifying opportunities and priorities for watershed restoration projects.

Geosphere process report for the safety assessment SR-Can

International Nuclear Information System (INIS)

Skagius, Kristina

2006-09-01

This report documents geosphere processes identified as relevant to the long-term safety of a KBS- repository, and forms an important part of the reporting of the safety assessment SR-Can. The detailed assessment methodology, including the role of the process report in the assessment, is described in the SR-Can Main report. The following excerpts describe the methodology, and clarify the role of this process report in the assessment. The repository system, broadly defined as the deposited spent nuclear fuel, the engineered barriers surrounding it, the host rock and the biosphere in the proximity of the repository, will evolve over time. Future states of the system will depend on the initial state of the system, a number of radiation related, thermal, hydraulic, mechanical, chemical and biological processes acting within the repository system over time, and external influences acting on the system. A methodology in ten steps has been developed for SR-Can described below. Identification of factors to consider (FEP processing): This step consists of identifying all the factors that need to be included in the analysis. Experience from earlier safety assessments and KBS-specific and international databases of relevant features, events and processes influencing long-term safety are utilised. Based on the results of the FEP processing, an SR-Can FEP catalogue, containing FEPs to be handled in SR-Can, has been established. The initial state of the system is described based on the design specifications of the KBS repository, a descriptive model of the repository site and a site-specific layout of the repository. The initial state of the fuel and the engineered components is that immediately after deposition, as described in the SR-Can Initial state report. The initial state of the geosphere and the biosphere is that of the natural system prior to excavation, as described in the site descriptive models. The repository layouts adapted to the sites are provided in underground

Geosphere process report for the safety assessment SR-Can

Energy Technology Data Exchange (ETDEWEB)

Skagius, Kristina [Kemakta Konsult AB, Stockholm (SE)] (ed.)

2006-09-15

This report documents geosphere processes identified as relevant to the long-term safety of a KBS- repository, and forms an important part of the reporting of the safety assessment SR-Can. The detailed assessment methodology, including the role of the process report in the assessment, is described in the SR-Can Main report. The following excerpts describe the methodology, and clarify the role of this process report in the assessment. The repository system, broadly defined as the deposited spent nuclear fuel, the engineered barriers surrounding it, the host rock and the biosphere in the proximity of the repository, will evolve over time. Future states of the system will depend on the initial state of the system, a number of radiation related, thermal, hydraulic, mechanical, chemical and biological processes acting within the repository system over time, and external influences acting on the system. A methodology in ten steps has been developed for SR-Can described below. Identification of factors to consider (FEP processing): This step consists of identifying all the factors that need to be included in the analysis. Experience from earlier safety assessments and KBS-specific and international databases of relevant features, events and processes influencing long-term safety are utilised. Based on the results of the FEP processing, an SR-Can FEP catalogue, containing FEPs to be handled in SR-Can, has been established. The initial state of the system is described based on the design specifications of the KBS repository, a descriptive model of the repository site and a site-specific layout of the repository. The initial state of the fuel and the engineered components is that immediately after deposition, as described in the SR-Can Initial state report. The initial state of the geosphere and the biosphere is that of the natural system prior to excavation, as described in the site descriptive models. The repository layouts adapted to the sites are provided in underground

Local Sustainable Energy Assessment Report of Quang Tri in Vietnam

DEFF Research Database (Denmark)

Andersen, Jan; Lund, Søren

The publication reports a sustainable energy assessment at the local project site of the HighARCS project in Nainital, Uttarakhand and Buxa, West Bengal, India. The assessment has been made as a contribution to the elaboration of biodiversity conservation and livelihoods improvement action plans...

Biological variables for the site survey of surface ecosystems - existing data and survey methods

International Nuclear Information System (INIS)

Kylaekorpi, Lasse; Berggren, Jens; Larsson, Mats; Liberg, Maria; Rydgren, Bernt

2000-06-01

In the process of selecting a safe and environmentally acceptable location for the deep level repository of nuclear waste, site surveys will be carried out. These site surveys will also include studies of the biota at the site, in order to assure that the chosen site will not conflict with important ecological interests, and to establish a thorough baseline for future impact assessments and monitoring programmes. As a preparation to the site survey programme, a review of the variables that need to be surveyed is conducted. This report contains the review for some of those variables. For each variable, existing data sources and their characteristics are listed. For those variables for which existing data sources are inadequate, suggestions are made for appropriate methods that will enable the establishment of an acceptable baseline. In this report the following variables are reviewed: Fishery, Landscape, Vegetation types, Key biotopes, Species (flora and fauna), Red-listed species (flora and fauna), Biomass (flora and fauna), Water level, water retention time (incl. water body and flow), Nutrients/toxins, Oxygen concentration, Layering, stratification, Light conditions/transparency, Temperature, Sediment transport, (Marine environments are excluded from this review). For a major part of the variables, the existing data coverage is most likely insufficient. Both the temporal and/or the geographical resolution is often limited, which means that complementary surveys must be performed during (or before) the site surveys. It is, however, in general difficult to make exact judgements on the extent of existing data, and also to give suggestions for relevant methods to use in the site surveys. This can be finally decided only when the locations for the sites are decided upon. The relevance of the different variables also depends on the environmental characteristics of the sites. Therefore, we suggest that when the survey sites are selected, an additional review is

Biological variables for the site survey of surface ecosystems - existing data and survey methods

Energy Technology Data Exchange (ETDEWEB)

Kylaekorpi, Lasse; Berggren, Jens; Larsson, Mats; Liberg, Maria; Rydgren, Bernt [SwedPower AB, Stockholm (Sweden)

2000-06-01

In the process of selecting a safe and environmentally acceptable location for the deep level repository of nuclear waste, site surveys will be carried out. These site surveys will also include studies of the biota at the site, in order to assure that the chosen site will not conflict with important ecological interests, and to establish a thorough baseline for future impact assessments and monitoring programmes. As a preparation to the site survey programme, a review of the variables that need to be surveyed is conducted. This report contains the review for some of those variables. For each variable, existing data sources and their characteristics are listed. For those variables for which existing data sources are inadequate, suggestions are made for appropriate methods that will enable the establishment of an acceptable baseline. In this report the following variables are reviewed: Fishery, Landscape, Vegetation types, Key biotopes, Species (flora and fauna), Red-listed species (flora and fauna), Biomass (flora and fauna), Water level, water retention time (incl. water body and flow), Nutrients/toxins, Oxygen concentration, Layering, stratification, Light conditions/transparency, Temperature, Sediment transport, (Marine environments are excluded from this review). For a major part of the variables, the existing data coverage is most likely insufficient. Both the temporal and/or the geographical resolution is often limited, which means that complementary surveys must be performed during (or before) the site surveys. It is, however, in general difficult to make exact judgements on the extent of existing data, and also to give suggestions for relevant methods to use in the site surveys. This can be finally decided only when the locations for the sites are decided upon. The relevance of the different variables also depends on the environmental characteristics of the sites. Therefore, we suggest that when the survey sites are selected, an additional review is

The Nirex safety assessment research programme: annual report for 1986/87

International Nuclear Information System (INIS)

Cooper, M.J.; Hodgkinson, D.P.

1987-05-01

This report describes research relating to the underground disposal of low-level and intermediate-level radioactive wastes, to provide information for post-emplacement radiological safety assessment. Topics reported are solubility and sorption, organic degradation, microbial activity, leaching, the corrosion of containers, and radionuclide migration studies. Properties of clays, slates, colloids and uranium disequilibrium are studied. Mathematical modelling to support the safety assessment of radioactive waste disposal is also studied. (U.K.)

Intensity-modulated conformal radiotherapy in the anal canal cancer. Report of technological assessment. Updating of the 2006 report

International Nuclear Information System (INIS)

2015-07-01

As intensity-modulated conformal radiotherapy (IMCR) has already been technologically assessed in 2006 with a positive opinion for some treatments and a negative one for others, and as this technique displays some interesting properties for the treatment of pelvic cancers (optimisation of dose distribution, preservation of sane tissues, reduction of secondary effects during irradiation), this report proposes an assessment of clinical safety and efficiency of IMCR in the treatment of an anal canal cancer. After a discussion of generalities, of histological and epidemiological data, and of knowledge regarding treatment and follow-up of this cancer, the report presents the IMCR technique, some regulatory aspects, and its applications to the considered cancer. The methodology adopted for this assessment is then presented. Based on various studies and clinical results, the IMCR clinical safety and efficiency in the treatment of the anal canal cancer are discussed and assessed. Recommendations produced by different medical professional bodies are reported. Opinion of experts and a synthesis of stakeholders are then proposed

National environmental/energy workforce assessment. national summary. Volume Four: South Dakota-Virgin Islands. Final report on phase 1

International Nuclear Information System (INIS)

1977-12-01

This study is one of 70 volumes assessing the workforce needs (manpower needs) for pollution control and abatement in the United States for the five-year period of 1976 through 1981. Seven fields for pollution control -- air, noise, pesticides, potable water, radiation, solid waste, and wastewater -- are analyzed, together with energy-related programs currently accentuated by the national effort to solve energy supply problems. The report identifies existing workforce levels, training programs, career opportunities, and future staffing level projections (1976 to 1982) based on the information available for the states of South Dakota through Wyoming and also the District of Columbia, Puerto Rico, and the Virgin Islands

Utility of Social Modeling for Proliferation Assessment - Enhancing a Facility-Level Model for Proliferation Resistance Assessment of a Nuclear Enegry System

Energy Technology Data Exchange (ETDEWEB)

Coles, Garill A.; Brothers, Alan J.; Gastelum, Zoe N.; Olson, Jarrod; Thompson, Sandra E.

2009-10-26

The Utility of Social Modeling for Proliferation Assessment project (PL09-UtilSocial) investigates the use of social and cultural information to improve nuclear proliferation assessments, including nonproliferation assessments, Proliferation Resistance (PR) assessments, safeguards assessments, and other related studies. These assessments often use and create technical information about a host State and its posture towards proliferation, the vulnerability of a nuclear energy system (NES) to an undesired event, and the effectiveness of safeguards. This objective of this project is to find and integrate social and technical information by explicitly considering the role of cultural, social, and behavioral factors relevant to proliferation; and to describe and demonstrate if and how social science modeling has utility in proliferation assessment. This report describes a modeling approach and how it might be used to support a location-specific assessment of the PR assessment of a particular NES. The report demonstrates the use of social modeling to enhance an existing assessment process that relies on primarily technical factors. This effort builds on a literature review and preliminary assessment performed as the first stage of the project and compiled in PNNL-18438. [ T his report describes an effort to answer questions about whether it is possible to incorporate social modeling into a PR assessment in such a way that we can determine the effects of social factors on a primarily technical assessment. This report provides: 1. background information about relevant social factors literature; 2. background information about a particular PR assessment approach relevant to this particular demonstration; 3. a discussion of social modeling undertaken to find and characterize social factors that are relevant to the PR assessment of a nuclear facility in a specific location; 4. description of an enhancement concept that integrates social factors into an existing, technically

Expert Meeting Report: Windows Options for New and Existing Homes

Energy Technology Data Exchange (ETDEWEB)

Ojczyk, C.; Carmody, J.; Haglund, K.

2013-05-01

The NorthernSTAR Building America Partnership held an Expert Meeting on Windows Options for New and Existing Homes on November 14, 2011 at the Nolte Building on the campus of the University of Minnesota in Minneapolis, MN. Featured speakers included John Carmody and Pat Huelman of the University of Minnesota, Charlie Curcija of Lawrence Berkeley National Laboratory, Jim Larson of Cardinal Glass Industries, Peter Yost of Building Green, Peter Baker of Building Science Corporation, and Theresa Weston of Du Pont Innovations. Audience participation was actively encouraged during each presentation to uncover need and promote dialog among researchers and industry professionals.

Expert Meeting Report. Windows Options for New and Existing Homes

Energy Technology Data Exchange (ETDEWEB)

Ojczyck, C. [Univ. of Minnesota, St. Paul, MN (United States); Carmody, J. [Univ. of Minnesota, St. Paul, MN (United States); Haglund, K. [Univ. of Minnesota, St. Paul, MN (United States)

2013-05-01

The NorthernSTAR Building America Partnership held an Expert Meeting on Windows Options for New and Existing Homes on November 14, 2011, at the Nolte Building on the campus of the University of Minnesota in Minneapolis, MN. Featured speakers included John Carmody and Pat Huelman of the University of Minnesota, Charlie Curcija of Lawrence Berkeley National Laboratory, Jim Larson of Cardinal Glass Industries, Peter Yost of Building Green, Peter Baker of Building Science Corporation, and Theresa Weston of Du Pont Innovations. Audience participation was actively encouraged during each presentation to uncover need and promote dialog among researchers and industry professionals.

Assess Current and Potential Salmonid Production in Rattlesnake Creek Associated with Restoration Efforts; US Geological Survey Reports, 2002-2003 Annual Report.

Energy Technology Data Exchange (ETDEWEB)

Connolly, Patrick J. (US Geological Survey, Columbia River Research Laboratory, Western Fisheries Research Center, Cook, WA)

2003-12-01

This project was designed to document existing habitat conditions and fish populations within the Rattlesnake Creek watershed (White Salmon River subbasin, Washington) before major habitat restoration activities are implemented and prior to the reintroduction of salmon and steelhead above Condit Dam. Returning adult salmon Oncorhynchus spp. and steelhead O. mykiss have not had access to Rattlesnake Creek since 1913. An assessment of resident trout populations should serve as a good surrogate for evaluation of factors that would limit salmon and steelhead production in the watershed. Personnel from United States Geological Survey's Columbia River Research Laboratory (USGS-CRRL) attend to three main objectives of the Rattlesnake Creek project. The first is to characterize stream and riparian habitat conditions. This effort includes measures of water quality, water quantity, stream habitat, and riparian conditions. The second objective is to determine the status of fish populations in the Rattlesnake Creek drainage. To accomplish this, we derived estimates of salmonid population abundance, determined fish species composition, assessed distribution and life history attributes, obtained tissue samples for genetic analysis, and assessed fish diseases in the watershed. The third objective is to use the collected habitat and fisheries information to help identify and prioritize areas in need of restoration. As this report covers the second year of at least a three-year study, it is largely restricted to describing our efforts and findings for the first two objectives.

Report Assesses Nutrient Pollution in U.S. Streams and Aquifers

Science.gov (United States)

Showstack, Randy

2010-10-01

Concentrations of nutrients in many U.S. streams and aquifers have remained the same or have increased since the early 1990s, according to a new decadal assessment entitled “Nutrients in the nation's streams and groundwater, 1992-2004,” released by the U.S. Geological Survey (USGS) on 24 September. “Despite improvements in water quality made by reducing point sources of nutrients, our data show that nonpoint sources of nutrients have resulted in concentrations of both nitrogen and phosphorus far above criteria recommended by [the U.S. Environmental Protection Agency] for the protection of aquatic life,” Neil Dubrovsky, project chief for USGS's National Water-Quality Assessment (NAWQA) Program, said at a briefing when the report was released. While USGS continues to sample for nutrient concentrations, the report assessment period concluded in 2004.

Reporting methods of blinding in randomized trials assessing nonpharmacological treatments.

Directory of Open Access Journals (Sweden)

Isabelle Boutron

2007-02-01

Full Text Available BACKGROUND: Blinding is a cornerstone of treatment evaluation. Blinding is more difficult to obtain in trials assessing nonpharmacological treatment and frequently relies on "creative" (nonstandard methods. The purpose of this study was to systematically describe the strategies used to obtain blinding in a sample of randomized controlled trials of nonpharmacological treatment. METHODS AND FINDINGS: We systematically searched in Medline and the Cochrane Methodology Register for randomized controlled trials (RCTs assessing nonpharmacological treatment with blinding, published during 2004 in high-impact-factor journals. Data were extracted using a standardized extraction form. We identified 145 articles, with the method of blinding described in 123 of the reports. Methods of blinding of participants and/or health care providers and/or other caregivers concerned mainly use of sham procedures such as simulation of surgical procedures, similar attention-control interventions, or a placebo with a different mode of administration for rehabilitation or psychotherapy. Trials assessing devices reported various placebo interventions such as use of sham prosthesis, identical apparatus (e.g., identical but inactivated machine or use of activated machine with a barrier to block the treatment, or simulation of using a device. Blinding participants to the study hypothesis was also an important method of blinding. The methods reported for blinding outcome assessors relied mainly on centralized assessment of paraclinical examinations, clinical examinations (i.e., use of video, audiotape, photography, or adjudications of clinical events. CONCLUSIONS: This study classifies blinding methods and provides a detailed description of methods that could overcome some barriers of blinding in clinical trials assessing nonpharmacological treatment, and provides information for readers assessing the quality of results of such trials.

Operational, cost, and technical study of large windpower systems integrated with an existing electric utility. Final report

Energy Technology Data Exchange (ETDEWEB)

Ligon, C.; Kirby, G.; Jordan, D.; Lawrence, J.H.; Wiesner, W.; Kosovec, A.; Swanson, R.K.; Smith, R.T.; Johnson, C.C.; Hodson, H.O.

1976-04-01

Detailed wind energy assessment from the available wind records, and evaluation of the application of wind energy systems to an existing electric utility were performed in an area known as the Texas Panhandle, on the Great Plains. The study area includes parts of Texas, eastern New Mexico, the Oklahoma Panhandle and southern Kansas. The region is shown to have uniformly distributed winds of relatively high velocity, with average wind power density of 0.53 kW/m/sup 2/ at 30 m height at Amarillo, Texas, a representative location. The annual period of calm is extremely low. Three separate compressed air storage systems with good potential were analyzed in detail, and two potential pumped-hydro facilities were identified and given preliminary consideration. Aquifer storage of compressed air is a promising possibility in the region.

Environmental Assessment Use of Existing Borrow Areas, Hanford Site, Richland, Washington

International Nuclear Information System (INIS)

2001-01-01

The U.S. Department of Energy (DOE) operates the Hanford Site near Richland, Washington. The DOE needs to identify and operate onsite locations for a continued supply of raw aggregate materials [approximately 7,600,000 cubic meters (10,000,000 cubic yards) over the next 10 years] for new facility construction, maintenance of existing facilities and transportation corridors, and fill and capping material for remediation and other sites

Minamata Convention on Mercury. Reporting obligations of the Parties to the Convention and the sources of data existing in Poland

Directory of Open Access Journals (Sweden)

Strzelecka-Jastrząb Ewa

2018-01-01

Full Text Available After that, when more than 60 years ago in the Japanese city of Minamata there was caused a mass poisoning of residents by seafood contaminated with mercury, Minamata Convention on Mercury came into force on August 16, 2017. To date, the Convention has been signed by 128 States, the signatories of the Convention and ratified by 83 States - Parties to the Convention. The Convention imposes a number of obligations on the Parties to the Convention, including the reporting obligation. The paper analyses the reporting obligations of the Parties to the Convention, which are in force after the entry into force of the Convention, pursuant to the provisions contained therein. In addition, the existing sources of quantitative data on mercury in Poland are characterized.

Validity of LIDAS (LIfetime Depression Assessment Self-report): a self-report online assessment of lifetime major depressive disorder.

Science.gov (United States)

Bot, M; Middeldorp, C M; de Geus, E J C; Lau, H M; Sinke, M; van Nieuwenhuizen, B; Smit, J H; Boomsma, D I; Penninx, B W J H

2017-01-01

There is a paucity of valid, brief instruments for the assessment of lifetime major depressive disorder (MDD) that can be used in, for example, large-scale genomics, imaging or biomarker studies on depression. We developed the LIfetime Depression Assessment Self-report (LIDAS), which assesses lifetime MDD diagnosis according to DSM criteria, and is largely based on the widely used Composite International Diagnostic Interview (CIDI). Here, we tested the feasibility and determined the sensitivity and specificity for measuring lifetime MDD with this new questionnaire, with a regular CIDI as reference. Sensitivity and specificity analyses of the online lifetime MDD questionnaire were performed in adults with (n = 177) and without (n = 87) lifetime MDD according to regular index CIDIs, selected from the Netherlands Study of Depression and Anxiety (NESDA) and Netherlands Twin Register (NTR). Feasibility was tested in an additional non-selective, population-based sample of NTR participants (n = 245). Of the 753 invited persons, 509 (68%) completed the LIDAS, of which 419 (82%) did this online. User-friendliness of the instrument was rated high. Median completion time was 6.2 min. Sensitivity and specificity for lifetime MDD were 85% [95% confidence interval (CI) 80-91%] and 80% (95% CI 72-89%), respectively. This LIDAS instrument gave a lifetime MDD prevalence of 20.8% in the population-based sample. Measuring lifetime MDD with an online instrument was feasible. Sensitivity and specificity were adequate. The instrument gave a prevalence of lifetime MDD in line with reported population prevalences. LIDAS is a promising tool for rapid determination of lifetime MDD status in large samples, such as needed for genomics studies.

Terrestrial laser scanning-based bridge structural condition assessment : InTrans project reports.

Science.gov (United States)

2016-05-01

Objective, accurate, and fast assessment of a bridges structural condition is critical to the timely assessment of safety risks. : Current practices for bridge condition assessment rely on visual observations and manual interpretation of reports a...

Battelle Energy Alliance, LLC (BEA) 2016 Self-Assessment Report for Idaho National Laboratory (INL)

International Nuclear Information System (INIS)

Alvarez, Juan

2016-01-01

This report provides Battelle Energy Alliance's (BEA) self-assessment of performance for the period of October 1, 2015, through September 30, 2016, as evaluated against the goals, performance objectives, and notable outcomes defined in the Fiscal Year (FY) 2016 Performance Evaluation and Measurement Plan (PEMP). BEA took into consideration and consolidated all input provided from internal and external sources (e.g., Contractor Assurance System [CAS], program and customer feedback, external and independent reviews, and Department of Energy [DOE] Idaho Operations Office [ID] quarterly PEMP reports and Quarterly Evaluation Reports). The overall performance of BEA during this rating period was self-assessed as 'Excellent,' exceeding expectations of performance in Goal 1.0, 'Efficient and Effective Mission Accomplishment'; Goal 2.0, 'Efficient and Effective Stewardship and Operation of Research Facilities'; and Goal 3.0, 'Sound and Competent Leadership and Stewardship of the Laboratory.' BEA met or exceeded expectations for Mission Support Goals 4.0 through 7.0 assessing a final multiplier of 1.0. Table 1 documents BEA's assessment of performance to the goals and individual performance objectives. Table 2 documents completion of the notable outcomes. A more-detailed assessment of performance for each individual performance objective is documented in the closeout reports (see the PEMP reporting system). Table 3 includes an update to 'Performance Challenges' as reported in the FY 2015 Self-Assessment Report.

Using R and WinBUGS to fit a generalized partial credit model for developing and evaluating patient-reported outcomes assessments.

Science.gov (United States)

Li, Yuelin; Baser, Ray

2012-08-15

The US Food and Drug Administration recently announced the final guidelines on the development and validation of patient-reported outcomes (PROs) assessments in drug labeling and clinical trials. This guidance paper may boost the demand for new PRO survey questionnaires. Henceforth, biostatisticians may encounter psychometric methods more frequently, particularly item response theory (IRT) models to guide the shortening of a PRO assessment instrument. This article aims to provide an introduction on the theory and practical analytic skills in fitting a generalized partial credit model (GPCM) in IRT. GPCM theory is explained first, with special attention to a clearer exposition of the formal mathematics than what is typically available in the psychometric literature. Then, a worked example is presented, using self-reported responses taken from the international personality item pool. The worked example contains step-by-step guides on using the statistical languages r and WinBUGS in fitting the GPCM. Finally, the Fisher information function of the GPCM model is derived and used to evaluate, as an illustrative example, the usefulness of assessment items by their information contents. This article aims to encourage biostatisticians to apply IRT models in the re-analysis of existing data and in future research. Copyright © 2012 John Wiley & Sons, Ltd.

Deep-ocean Assessment and Reporting of Tsunamis (DART) Stations

Data.gov (United States)

Department of Homeland Security — As part of the U.S. National Tsunami Hazard Mitigation Program (NTHMP), the Deep Ocean Assessment and Reporting of Tsunamis (DART(R)) Project is an ongoing effort to...

High level waste storage tanks 242-A evaporator S/RID phase II assessment report

Energy Technology Data Exchange (ETDEWEB)

Biebesheimer, E.

1996-09-27

This document, the Standards/Requirements Identification Document (S/RID) Phase 2 Assessment Report for the subject facility, represents the results of a Performance Assessment to determine whether procedures containing S/RID requirements are fully implemented by field personnel in the field. It contains a summary report and three attachments; an assessment schedule, performance objectives, and assessments for selected functional areas.

Model summary report for the safety assessment SFR 1 SAR-08

Energy Technology Data Exchange (ETDEWEB)

2008-03-15

This document is the model summary report for the safety assessment SFR 1 SAR-08. In the report, the quality assurance measures conducted for the assessment codes are presented together with the chosen methodology. In the safety assessment SFR1 SAR-08, a number of different computer codes are used. In order to better understand how these codes are related an Assessment Model Flowchart, AMF, has been produced within the project. From the AMF, it is possible to identify the different modelling tasks and consequently also the different computer codes used. A number of different computer codes are used in the assessment of which some are commercial while others are developed for assessment projects. QA requirements must on the one hand take this diversity into account and on the other hand be well defined. In the methodology section of the report the following requirements are defined: - It must be demonstrated that the code is suitable for its purpose. - It must be demonstrated that the code has been properly used. - It must be demonstrated that the code development process has followed appropriate procedures and that the code produces accurate results. Although the requirements are identical for all codes, the measures used to show that the requirements are fulfilled will be different for different codes (for instance due to the fact that for some software the source-code is not available for review). Subsequent to the methodology section, each assessment code is presented and it is shown how the requirements are met

Model summary report for the safety assessment SFR 1 SAR-08

International Nuclear Information System (INIS)

2008-03-01

This document is the model summary report for the safety assessment SFR 1 SAR-08. In the report, the quality assurance measures conducted for the assessment codes are presented together with the chosen methodology. In the safety assessment SFR1 SAR-08, a number of different computer codes are used. In order to better understand how these codes are related an Assessment Model Flowchart, AMF, has been produced within the project. From the AMF, it is possible to identify the different modelling tasks and consequently also the different computer codes used. A number of different computer codes are used in the assessment of which some are commercial while others are developed for assessment projects. QA requirements must on the one hand take this diversity into account and on the other hand be well defined. In the methodology section of the report the following requirements are defined: - It must be demonstrated that the code is suitable for its purpose. - It must be demonstrated that the code has been properly used. - It must be demonstrated that the code development process has followed appropriate procedures and that the code produces accurate results. Although the requirements are identical for all codes, the measures used to show that the requirements are fulfilled will be different for different codes (for instance due to the fact that for some software the source-code is not available for review). Subsequent to the methodology section, each assessment code is presented and it is shown how the requirements are met

241-AY Double Shell Tanks (DST) Integrity Assessment Report

Energy Technology Data Exchange (ETDEWEB)

JENSEN, C.E.

1999-09-21

This report presents the results of the integrity assessment of the 241-AY double-shell tank farm facility located in the 200 East Area of the Hanford Site. The assessment included the design evaluation and integrity examinations of the tanks and concluded that the facility is adequately designed, is compatible with the waste, and is fit for use. Recommendations including subsequent examinations. are made to ensure the continued safe operation of the tanks.

241-AN Double Shell Tanks (DST) Integrity Assessment Report

International Nuclear Information System (INIS)

JENSEN, C.E.

1999-01-01

This report presents the results of the integrity assessment of the 241-AN double-shell tank farm facility located in the 200 East Area of the Hanford Site. The assessment included the design evaluation and integrity examinations of the tanks and concluded that the facility is adequately designed, is compatible with the waste, and is fit for use. Recommendations including subsequent examinations, are made to ensure the continued safe operation of the tanks

241-AY Double Shell Tanks (DST) Integrity Assessment Report

International Nuclear Information System (INIS)

JENSEN, C.E.

1999-01-01

This report presents the results of the integrity assessment of the 241-AY double-shell tank farm facility located in the 200 East Area of the Hanford Site. The assessment included the design evaluation and integrity examinations of the tanks and concluded that the facility is adequately designed, is compatible with the waste, and is fit for use. Recommendations including subsequent examinations, are made to ensure the continued safe operation of the tanks

241-SY Double Shell Tanks (DST) Integrity Assessment Report

International Nuclear Information System (INIS)

JENSEN, C.E.

1999-01-01

This report presents the results of the integrity assessment of the 241-SY double-shell tank farm facility located in the 200 West Area of the Hanford Site. The assessment included the design evaluation and integrity examinations of the tanks and concluded that the facility is adequately designed, is compatible with the waste, and is fit for use. Recommendations including subsequent examinations, are made to ensure the continued safe operation of the tanks

241-AZ Double-Shell Tanks (DST) Integrity Assessment Report

International Nuclear Information System (INIS)

JENSEN, C.E.

1999-01-01

This report presents the results of the integrity assessment of the 241-A2 double-shell tank farm facility located in the 200 East Area of the Hanford Site. The assessment included the design evaluation and integrity examinations of the tanks and concluded that the facility is adequately designed, is compatible with the waste, and is fit for use. Recommendations including subsequent examinations, are made to ensure the continued safe operation of the tanks

241-AW Double Shell Tanks (DST) Integrity Assessment Report

International Nuclear Information System (INIS)

JENSEN, C.E.

1999-01-01

This report presents the results of the integrity assessment of the 241-AW double-shell tank farm facility located in the 200 East Area of the Hanford Site. The assessment included the design evaluation and integrity examinations of the tanks and concluded that the facility is adequately designed, is compatible with the waste, and is fit for use. Recommendations including subsequent examinations, are made to ensure the continued safe operation of the tanks

Environmental Hazards Assessment Program quarterly report, January--March 1995

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-04-30

The objectives of the Environmental Hazards Assessment Program (EHAP) stated in the proposal to DOE are to: develop a holistic, national basis for risk assessment, risk management, and risk communication that recognizes the direct impact of environmental hazards on the health and well-being of all; develop a pool of talented scientists and experts in cleanup activities, especially in human health aspects; and identify needs and develop programs addressing the critical shortage of well-educated, highly-skilled technical and scientific personnel to address the health oriented aspects of environmental restoration and waste management. This report describes activities and reports on progress for the third quarter (January--March) of the third year of the grant. It reports progress against these grant objectives and the Program Implementation Plan published at the end of the first year of the grant. Questions, comments, or requests for further information concerning the activities under this grant can be forwarded to Jack Davis in the EHAP office of the Medical University of South Carolina at (803) 727-6450.

The design value method and adjusted partial factor approach for existing structures

NARCIS (Netherlands)

Caspeele, R.; Sykora, M.; Allaix, D.L.; Steenbergen, R.D.J.M.

2013-01-01

In contrast to the design of new structures, the assessment of existing structures often relies on the subjective judgement of the investigating engineer. An objective verification format for existing structures based on alternative partial factors is however feasible, enabling a rather simple and

Battelle Energy Alliance, LLC (BEA) 2016 Self-Assessment Report for Idaho National Laboratory (INL)

Energy Technology Data Exchange (ETDEWEB)

Alvarez, Juan [Idaho National Lab. (INL), Idaho Falls, ID (United States)

2016-10-01

This report provides Battelle Energy Alliance’s (BEA) self-assessment of performance for the period of October 1, 2015, through September 30, 2016, as evaluated against the goals, performance objectives, and notable outcomes defined in the Fiscal Year (FY) 2016 Performance Evaluation and Measurement Plan (PEMP). BEA took into consideration and consolidated all input provided from internal and external sources (e.g., Contractor Assurance System [CAS], program and customer feedback, external and independent reviews, and Department of Energy [DOE] Idaho Operations Office [ID] quarterly PEMP reports and Quarterly Evaluation Reports). The overall performance of BEA during this rating period was self-assessed as “Excellent,” exceeding expectations of performance in Goal 1.0, “Efficient and Effective Mission Accomplishment”; Goal 2.0, “Efficient and Effective Stewardship and Operation of Research Facilities”; and Goal 3.0, “Sound and Competent Leadership and Stewardship of the Laboratory.” BEA met or exceeded expectations for Mission Support Goals 4.0 through 7.0 assessing a final multiplier of 1.0. Table 1 documents BEA’s assessment of performance to the goals and individual performance objectives. Table 2 documents completion of the notable outcomes. A more-detailed assessment of performance for each individual performance objective is documented in the closeout reports (see the PEMP reporting system). Table 3 includes an update to “Performance Challenges” as reported in the FY 2015 Self-Assessment Report.

FEP report for the safety assessment SR-Can

International Nuclear Information System (INIS)

Skagius, Kristina

2006-11-01

This report documents the analysis and processing of features, events and processes, FEPs, that has been carried out within the safety assessment SR-Can, and forms an important part of the reporting of the project. The SR-Can project is a preparatory stage for the SR-Site assessment, and the report from that project will be used in support of SKB's application to build a final repository. The overall objective of the FEP analysis and processing included development of a database of features, events and processes, an SKB FEP database, in a format that facilitates both a systematic analysis of FEPs and documentation of that FEP analysis, as well as facilitating revisions and updates to be made in connection with new safety assessments. The overall objective also extended to the development of procedures for such a systematic FEP analysis as well as the application of those procedures in order to establish an SR-Can FEP catalogue within the framework of the SKB FEP database. The work started by implementing the content of the SR 97 Process Report into a database format suitable for import and processing of FEP information from other sources. The SR 97 version of the database was systematically audited against the NEA database with Project FEPs, version 1.2. In addition, an earlier audit of the SR 97 process report against the interaction matrices developed for a deep repository of the KBS-3 type was revisited and updated. Relevant FEPs identified through the audit process were sorted into three main categories i) FEPs related to the initial states of the repository system, ii) FEPs related to internal processes of the repository system, and iii) FEPs related to external impacts on the repository system. This resulted in additions to the SR 97 list of processes and to the lists of initial state FEPs and external factors to be addressed in further processing. The further processing of the initial state FEPs revealed that those FEPs that are not covered by the

Assess Current and Potential Salmonid Production in Rattlesnake Creek in Association with Restoration Efforts, US Geological Survey Report, 2004-2005 Annual Report.

Energy Technology Data Exchange (ETDEWEB)

Allen, M. Brady; Connolly, Patrick J.; Jezorek, Ian G. (US Geological Survey, Western Fisheries Research Center, Columbia River Research Laboratory, Cook, WA)

2006-06-01

This project was designed to document existing habitat conditions and fish populations within the Rattlesnake Creek watershed (White Salmon River subbasin, Washington) before major habitat restoration activities are implemented and prior to the reintroduction of salmon and steelhead above Condit Dam. Returning adult salmon Oncorhynchus spp. and steelhead O. mykiss have not had access to Rattlesnake Creek since 1913. An assessment of resident trout populations should serve as a good surrogate for evaluation of factors that would limit salmon and steelhead production in the watershed. Personnel from United States Geological Survey's Columbia River Research Laboratory (USGS-CRRL) attended to three main objectives of the Rattlesnake Creek project. The first objective was to characterize stream and riparian habitat conditions. This effort included measures of water quality, water quantity, stream habitat, and riparian conditions. The second objective was to determine the status of fish populations in the Rattlesnake Creek drainage. To accomplish this, we derived estimates of salmonid population abundance, determined fish species composition, assessed distribution and life history attributes, obtained tissue samples for genetic analysis, and assessed fish diseases in the watershed. The third objective was to use the collected habitat and fisheries information to help identify and prioritize areas in need of restoration. As this report covers the fourth year of a five-year study, it is largely restricted to describing our efforts and findings for the first two objectives.

Assess Current and Potential Salmonid Production in Rattlesnake Creek in Association with Restoration Effors; US Geological Survey Reports, 2003-2004 Annual Report.

Energy Technology Data Exchange (ETDEWEB)

Allen, M. Brady; Connolly, Patrick J.; Munz, Carrie S. (US Geological Survey, Western Fisheries Research Center, Columbia River Research Laboratory, Cook, WA)

2006-02-01

This project was designed to document existing habitat conditions and fish populations within the Rattlesnake Creek watershed (White Salmon River subbasin, Washington) before major habitat restoration activities are implemented and prior to the reintroduction of salmon and steelhead above Condit Dam. Returning adult salmon Oncorhynchus spp. and steelhead O. mykiss have not had access to Rattlesnake Creek since 1913. An assessment of resident trout populations should serve as a good surrogate for evaluation of factors that would limit salmon and steelhead production in the watershed. Personnel from United States Geological Survey's Columbia River Research Laboratory (USGS-CRRL) attend to three main objectives of the Rattlesnake Creek project. The first is to characterize stream and riparian habitat conditions. This effort includes measures of water quality, water quantity, stream habitat, and riparian conditions. The second objective is to determine the status of fish populations in the Rattlesnake Creek drainage. To accomplish this, we derived estimates of salmonid population abundance, determined fish species composition, assessed distribution and life history attributes, obtained tissue samples for genetic analysis, and assessed fish diseases in the watershed. The third objective was to use the collected habitat and fisheries information to help identify and prioritize areas in need of restoration. As this report covers the third year of at least a five-year study, it is largely restricted to describing our efforts and findings for the first two objectives.

296-B-5 Stack monitoring and sampling system annual system assessment report

International Nuclear Information System (INIS)

Ridge, T.M.

1995-02-01

The B Plant Administration Manual requires an annual system assessment to evaluate and report the present condition of the sampling and monitoring system associated with Stack 296-B-5 at B Plant. The sampling and monitoring system associated with stack 296-B-5 is functional and performing satisfactorily. This document is an annual assessment report of the systems associated with the 296-B-5 stack

Co-existing sarcoidosis and Takayasu arteritis: report of a case

Directory of Open Access Journals (Sweden)

Hamzaoui Amira

2011-02-01

Full Text Available Abstract Introduction Takayasu arteritis (TA is a chronic vasculitis of unknown origin, affecting mainly the aorta and its main branches. As a result of the inflammation, stenosis, occlusion or dilatation of the involved vessels may occur and cause a wide range of symptoms. It has been described in association with various auto-immune disorders (mainly inflammatory digestive tract diseases. However, only few cases of TA associated with sarcoidosis have been reported, raising the question of an association by chance. Case report We report a case of a 34 year-old woman, with one year history of sarcoidosis, who presented with asymmetric high hypertension revealing inflammatory humeral, axillary and subclavian arteritis related to TA, successfully treated by steroid and immunosuppressive therapy(MethotrexateR. Conclusion TA and sarcoidosis may be related, rising the hypothesis that TA or Takayasu arteritis-like granulomatous vasculitis may be, in fact, a complication of sarcoidosis.

Deep-Ocean Assessment and Reporting of Tsunamis (DART(R))

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — As part of the U.S. National Tsunami Hazard Mitigation Program (NTHMP), the Deep Ocean Assessment and Reporting of Tsunamis (DART(R)) Project is an ongoing effort to...

Facility Interface Capability Assessment (FICA) project report

International Nuclear Information System (INIS)

Pope, R.B.; MacDonald, R.R.; Viebrock, J.M.; Mote, N.

1995-09-01

The US Department of Energy's (DOE) Office of Civilian Radioactive Waste Management (OCRWM) is responsible for developing the Civilian Radioactive Waste Management System (CRWMS) to accept spent nuclear fuel from commercial facilities. The objective of the Facility Interface Capability Assessment (FICA) project was to assess the capability of each commercial spent nuclear fuel (SNF) storage facility, at which SNF is stored, to handle various SNF shipping casks. The purpose of this report is to present and analyze the results of the facility assessments completed within the FICA project. During Phase 1, the data items required to complete the facility assessments were identified and the database for the project was created. During Phase 2, visits were made to 122 facilities on 76 sites to collect data and information, the database was updated, and assessments of the cask-handling capabilities at each facility were performed. Each assessment of cask-handling capability contains three parts: the current capability of the facility (planning base); the potential enhanced capability if revisions were made to the facility licensing and/or administrative controls; and the potential enhanced capability if limited physical modifications were made to the facility. The main conclusion derived from the planning base assessments is that the current facility capabilities will not allow handling of any of the FICA Casks at 49 of the 122 facilities evaluated. However, consideration of potential revisions and/or modifications showed that all but one of the 49 facilities could be adapted to handle at least one of the FICA Casks. For this to be possible, facility licensing, administrative controls, and/or physical aspects of the facility would need to be modified

Facility Interface Capability Assessment (FICA) project report

Energy Technology Data Exchange (ETDEWEB)

Pope, R.B. [ed.] [Oak Ridge National Lab., TN (United States); MacDonald, R.R. [ed.] [Civilian Radioactive Waste Management System, Vienna, VA (United States); Viebrock, J.M.; Mote, N. [Nuclear Assurance Corp., Norcross, GA (United States)

1995-09-01

The US Department of Energy`s (DOE) Office of Civilian Radioactive Waste Management (OCRWM) is responsible for developing the Civilian Radioactive Waste Management System (CRWMS) to accept spent nuclear fuel from commercial facilities. The objective of the Facility Interface Capability Assessment (FICA) project was to assess the capability of each commercial spent nuclear fuel (SNF) storage facility, at which SNF is stored, to handle various SNF shipping casks. The purpose of this report is to present and analyze the results of the facility assessments completed within the FICA project. During Phase 1, the data items required to complete the facility assessments were identified and the database for the project was created. During Phase 2, visits were made to 122 facilities on 76 sites to collect data and information, the database was updated, and assessments of the cask-handling capabilities at each facility were performed. Each assessment of cask-handling capability contains three parts: the current capability of the facility (planning base); the potential enhanced capability if revisions were made to the facility licensing and/or administrative controls; and the potential enhanced capability if limited physical modifications were made to the facility. The main conclusion derived from the planning base assessments is that the current facility capabilities will not allow handling of any of the FICA Casks at 49 of the 122 facilities evaluated. However, consideration of potential revisions and/or modifications showed that all but one of the 49 facilities could be adapted to handle at least one of the FICA Casks. For this to be possible, facility licensing, administrative controls, and/or physical aspects of the facility would need to be modified.

Report to Congress on Sustainable Ranges, 2011

Science.gov (United States)

2011-07-01

Tortugas and Fort Jefferson. 3. The ASUW Mission Area for the range complex was deleted for the 2011 assessment; the assessment dropped from 9.09 to...Comments Noise Restrictions Anti-Air Warfare (AAW) Sonic booms generated by VFA aircraft in the vicinity of the Dry Tortugas reportedly startles...Environmental Assessment recommended stipulating the expansion of an existing buffer zone around the Dry Tortugas by 2,000 feet, from 18,000 to 20,000

105-B Reactor museum feasibility assessment (Phase 2) project

International Nuclear Information System (INIS)

Heckel, R. P.

2000-01-01

This 105-B Reactor Museum feasibility assessment project report documents project activities that have been performed, including a review and assessment of previously existing information, a walk-through of the facility, an assessment of potential hazards, and selection of mitigative measures deemed to be appropriate to allow unescorted access by members of the public to a specified primary tour route

Powerplant productivity improvement study: policy analysis and incentive assessment. Final report

Energy Technology Data Exchange (ETDEWEB)

None

1979-05-01

Policy options that the Illinois Commerce Commission might adopt in order to promote improved power plant productivity for existing units in Illinois are identified and analyzed. These policy options would generally involve either removing existing disincentives and/or adding direct incentives through the regulatory process. The following activities are reported: in-depth review of existing theoretical and empirical literature in the areas of power plant reliability, regulatory utility efficiency and performance incentives, and impacts of various regulatory mechanisms such as the Fuel Adjustment Clauses on productivity; contacts with other state public utility commissions known to be investigating or implementing productivity improvement incentive mechanisms; documentation and analysis of incentive mechanisms adopted or under consideration in other states; analysis of current regulatory practice in Illinois as it relates to power plant productivity incentives and disincentives; identification of candidate incentive mechanisms for consideration by the Illinois Commerce Commission; and analysis and evaluation of these candidates. 72 references, 8 figures.

SPAT 15 - Assessment

Energy Technology Data Exchange (ETDEWEB)

Bartley, J.C. (Coordinator)

1998-08-01

In the Spring of 1997, the Department of Energy's Department Standards Committee (DSC) convened a Standards Process Action Team (SPAT-15) to evaluate assessment processes within the DOE complex. If time and resources permitted, the team was also to evaluate assessment processes used by private industry conducting similar work and activities. The specific task statement was as follows: "Define the attributes of assessment programs that effectively support organizational feedback and improvement of safety systems at all the different levels of contractor and Department organizations." The team gathered information on existing assessment programs through surveys and presentations by representatives from national laboratories, processing facilities, and remediation sites. Examples of assessment programs described in this report encompass site-wide, individual facility, and task level applications within the DOE compIex

SPAT 15 - Assessment

International Nuclear Information System (INIS)

Bartley, J.C.

1998-01-01

In the Spring of 1997, the Department of Energy's Department Standards Committee (DSC) convened a Standards Process Action Team (SPAT-15) to evaluate assessment processes within the DOE complex. If time and resources permitted, the team was also to evaluate assessment processes used by private industry conducting similar work and activities. The specific task statement was as follows: ''Define the attributes of assessment programs that effectively support organizational feedback and improvement of safety systems at all the different levels of contractor and Department organizations.'' The team gathered information on existing assessment programs through surveys and presentations by representatives from national laboratories, processing facilities, and remediation sites. Examples of assessment programs described in this report encompass site-wide, individual facility, and task level applications within the DOE compIex

Planning report for the safety assessment SR-Can

Energy Technology Data Exchange (ETDEWEB)

NONE

2003-06-01

This document is a planning report for SKB's next assessment of long-term safety for a KBS 3 repository. The assessment, SR-Can, is to be finished by the end of 2005 and will be used for SKB's application to build an Encapsulation plant for spent nuclear fuel. Apart from outlining the methodology, the report discusses the handling in SR-Can of a number of important issues regarding the near field, the geosphere, the biosphere, the climatic evolution etc. The Swedish nuclear safety and radiation protection authorities have recently issued regulations concerning the final disposal of nuclear waste. The principal compliance criterion states that the annual risk of harmful effects must not exceed 10{sup -6} for a representative individual in the group exposed to the greatest risk. There are also a number of requirements on methodological aspects of the safety assessment as well as on the contents of a safety report. The regulations are reproduced in an Appendix to this report. The primary safety function of the KBS 3 system is to completely isolate the spent nuclear fuel within copper canisters over the entire assessment period, which will be one million years in SR-Can. Should a canister be damaged, the secondary safety function is to retard any releases from the canisters. The main steps of the assessment are the following: 1. Qualitative system description, FEP processing: This step consists of defining a system boundary and of describing the system on a format suitable for the safety assessment. Databases of relevant features, events and processes influencing long-term safety are structured and used as one starting point for the assessment. 2. Initial state descriptions. 3. Process descriptions: In this step all identified processes within the system boundary involved in the long-term evolution of the system are described in detail. 4. Description of boundary conditions: This step is a broad description of the evolution of the boundaries of the system

Participation and Performance Reporting for the Alternate Assessment Based on Modified Achievement Standards (AA-MAS). Technical Report 58

Science.gov (United States)

Albus, Deb; Thurlow, Martha L.; Lazarus, Sheryl S.

2011-01-01

This report examines publicly reported participation and performance data for the alternate assessment based on modified achievement standards (AA-MAS). The authors' analysis of these data included all states publicly reporting AA-MAS data, regardless of whether they had received approval to use the results for Title I accountability calculations.…

Malawi : Country Procurement Assessment Report, Volume 1. Main Findings and Recommendations

OpenAIRE

World Bank

2004-01-01

The Malawi Country Procurement Assessment Report is a joint undertaking between the Malawi Government and the World Bank to analyze the country procurement system and recommend appropriate actions to improve the efficiency, economy and transparency of the system. This report is divided into (a) an Executive Summary, (b) Main Report on Findings and Recommendations, and (c) Annexes. Since th...

Local Sustainable Energy Assessment Report of the Guandong Province in China

DEFF Research Database (Denmark)

Andersen, Jan; Lund, Søren

The publication reports a sustainable energy assessment at the local project site of the HighARCS project in Shaoguan, Guangdong Province, China. The assessment has been made as a contribution to the elaboration of biodiversity conservation and livelihoods improvement action plans. It proposes...

Waste Isolation Pilot Plant Technical Assessment Team Report

Energy Technology Data Exchange (ETDEWEB)

None, None

2015-03-17

This report provides the results of the Waste Isolation Pilot Plant (WIPP) technical assessment led by the Savannah River National Laboratory and conducted by a team of experts in pertinent disciplines from SRNL and Lawrence Livermore National Laboratory (LLNL), Oak Ridge National Laboratory (ORNL), Pacific Northwest National Laboratory (PNNL), and Sandia National Laboratories (SNL).

Life Cycle Assessment Modelling of Greenhouse Gas Emissions from Existing and Proposed Municipal Solid Waste Management System of Lahore, Pakistan

Directory of Open Access Journals (Sweden)

Adila Batool Syeda

2017-12-01

Full Text Available Open Dumping of indiscriminate municipal solid waste (MSW remarkably contributes to global warming (GW. Life Cycle Assessment modelling may be a useful tool for assessing the best waste management option regarding GW potential. The current study evaluates the contribution of an existing MSW management (MSWM system to greenhouse gases in Gulberg Town, Lahore, Pakistan. This research also presents a comparison of scenarios with different waste management options. Life Cycle Assessment methodology has been used to conduct the study. EASETECH has been used for modelling. The short-term scenarios (STSs have been developed to promote the thinking of integration of treatment technologies in the current waste management system within a few months. The results show that the major contribution to the total emissions comes from the anaerobic digestion of organic material from open waste dumps. Currently, recycling is the best treatment option for reducing the CO2-eq values in the study area. It was clarified that recycling is the best option for reducing the CO2-eq values, whereas biogasification comes in second in terms of savings and reduction. The integration of recycling and biogasification techniques would be a good solution.

Development and validation of a patient-reported questionnaire assessing systemic therapy induced diarrhea in oncology patients.

Science.gov (United States)

Lui, Michelle; Gallo-Hershberg, Daniela; DeAngelis, Carlo

2017-12-22

Systemic therapy-induced diarrhea (STID) is a common side effect experienced by more than half of cancer patients. Despite STID-associated complications and poorer quality of life (QoL), no validated assessment tools exist to accurately assess STID occurrence and severity to guide clinical management. Therefore, we developed and validated a patient-reported questionnaire (STIDAT). The STIDAT was developed using the FDA iterative process for patient-reported outcomes. A literature search uncovered potential items and questions for questionnaire construction used by oncology clinicians to develop questions for the preliminary instrument. The instrument was evaluated on its face validity and content validity by patient interviews. Repetitive, similar and different themes uncovered from patient interviews were implemented to revise the instrument to the version used for validation. Patients starting high-risk STID treatments were monitored using the STIDAT, bowel diaries and EORTC QLQ-C30. The STIDAT was evaluated for construct validity using exploratory factor analysis (EFA) using minimal residual method with Promax rotation, reliability and consistency. A weighted scoring system was developed and a receiver-operating characteristic (ROC) curve evaluated the tool's ability to detect STID occurrence. Median scores and variability were analysed to determine how well it differentiates between diarrhea severities. A post-hoc analysis determined how diarrhea severity impacted QoL of cancer patients. Patients defined diarrhea based on presence of watery stool. The STIDAT assessed patient's perception of having diarrhea, daily number of bowel movements, daily number of diarrhea episodes, antidiarrheal medication use, the presence of urgency, abdominal pain, abdominal spasms or fecal incontinence, patient's perception of diarrhea severity, and QoL. These dimensions were sorted into four clusters using EFA - patient's perception of diarrhea, frequency of diarrhea, fecal

Assessing quality of reports on randomized clinical trials in nursing journals.

Science.gov (United States)

Parent, Nicole; Hanley, James A

2009-01-01

Several surveys have presented the quality of reports on randomized clinical trials (RCTs) published in general and specialty medical journals. The aim of these surveys was to raise scientific consciousness on methodological aspects pertaining to internal and external validity. These reviews have suggested that the methodological quality could be improved. We conducted a survey of reports on RCTs published in nursing journals to assess their methodological quality. The features we considered included sample size, flow of participants, assessment of baseline comparability, randomization, blinding, and statistical analysis. We collected data from all reports of RCTs published between January 1994 and December 1997 in Applied Nursing Research, Heart & Lung and Nursing Research. We hand-searched the journals and included all 54 articles in which authors reported that individuals have been randomly allocated to distinct groups. We collected data using a condensed form of the Consolidated Standards of Reporting Trials (CONSORT) statement for structured reporting of RCTs (Begg et al., 1996). Sample size calculations were included in only 22% of the reports. Only 48% of the reports provided information about the type of randomization, and a mere 22% described blinding strategies. Comparisons of baseline characteristics using hypothesis tests were abusively produced in more than 76% of the reports. Excessive use and unstructured reports of significance testing were common (59%), and all reports failed to provide magnitude of treatment differences with confidence intervals. Better methodological quality in reports of RCTs will contribute to increase the standards of nursing research.

Convergence between parent report and direct assessment of language and attention in culturally and linguistically diverse children.

Science.gov (United States)

Ebert, Kerry Danahy

2017-01-01

Parent report is commonly used to assess language and attention in children for research and clinical purposes. It is therefore important to understand the convergent validity of parent-report tools in comparison to direct assessments of language and attention. In particular, cultural and linguistic background may influence this convergence. In this study a group of six- to eight-year old children (N = 110) completed direct assessments of language and attention and their parents reported on the same areas. Convergence between assessment types was explored using correlations. Possible influences of ethnicity (Hispanic or non-Hispanic) and of parent report language (English or Spanish) were explored using hierarchical linear regression. Correlations between parent report and direct child assessments were significant for both language and attention, suggesting convergence between assessment types. Ethnicity and parent report language did not moderate the relationships between direct child assessments and parent report tools for either attention or language.

Interim report - geotechnical site assessment methodology. Vol.1

International Nuclear Information System (INIS)

Tunbridge, L.W.; Richards, L.R.

1983-05-01

An interim report summarizing the research conducted on geotechnical site assessment methodology at the Carwynnen test mine in Cornwall. The geological setting of the test site in the Cornubian granite batholith is described. The effect of structure imposed by discontinuities on the engineering behaviour of rock masses is discussed and the scanline survey method of obtaining data on discontinuities in the rock mass is described. The requirement for remote geophysical methods of characterizing the mass is discussed and initial experiments using seismic and ultrasonic velocity measurements are reported. Computer programs to perform statistical analysis of the discontinuity patterns are described. Overcoring and hydraulic fracturing methods of determining the in-situ stress are briefly described and the results of a programme of in-situ stress measurements using the overcoring method are reported. (author)

Assessing the quality of corporate social responsibility reports: the case of reporting practices in selected European Union member states.

Science.gov (United States)

Hąbek, Patrycja; Wolniak, Radosław

The organization may communicate its engagement in sustainability and may presents results achieved in this field by creating and publishing corporate social responsibility (CSR) reports. Today, we can observe a growing number of companies issuing such reports as a part of their annual reports or as stand-alone CSR reports. Despite the increase in the number of such reports their quality is different. CSR reports do not always provide complete data that readers desire, which in turn intensifies the problem with the evaluation and comparison of the organization's results achieved in this scope. Differences also occur between reporting models used in different EU countries caused by, inter alia, differently applied EU legislation on the disclosure of non-financial information in different Member States. This paper is one of the first attempts to perform a quantitative and qualitative analysis of corporate sustainability reporting practices in several European Union countries. The purpose of this article is to present the current state of CSR reporting practices in selected EU Member States and identify the differences in the quality and level of this kind of practices, taking into account the mandatory and voluntary model of disclosure. The study included separate CSR reports as well as annual reports with CSR sections and integrated reports published in 2012 in six selected EU Member States. The authors have used a specific evaluation tool in the examination of the individual reports. The assessment questionnaire consists of seventeen criteria grouped into two categories (relevance and credibility of information). In order to assess the quality of examined reports, the authors aggregated the indicators related with the reporting practices. The findings show that the quality level of the studied reports is generally low. Referring to its components, the relevance of the information provided in the assessed reports is at the higher level than its credibility. The

Application of Microgravity to the Assessment of Existing Structures and Structural Foundations.

Science.gov (United States)

1988-04-29

UADGU Geophysique Francafse IUSRSU 6c. ADDRESS (City, State. and ZIP Code) 7b. ADDRESS (City, State, and ZIP Code) 20, Rue des Pavilions Box 65 92800...r (2.8 - 2.4) 286 AM~TCT f eldo f6 YOUOUVT 4. EXISTING STRUCTURES AND (U) CONPAGNIE DE PROSPECTION GEOPHYSIQUE FRANCAISE RUEIL-MALNAISO J LAKSHNRNRN

Assessment of subsurface VOCs using a chemical microsensor array. Final report

Energy Technology Data Exchange (ETDEWEB)

Batterman, S.A.; Zellers, E.T. [Michigan Univ., Ann Arbor, MI (United States). School of Public Health

1993-06-01

This report describes the results of laboratory investigations of several performance parameters relevant to surface-acoustic-wave (SAW) chemical sensor arrays for the measurement of volatile organic compounds (VOCs) in contaminated soil and groundwater. The small size, low cost, sensitivity and selectivity of such instruments promise improvements in the quality and quantity of data used to guide site assessment and restoration efforts. In this investigation, calibrations were performed for 15 different coated SAW sensors. Each sensor was exposed to six VOCs selected to represent three chemical classes of contaminants that are commonly found at waste sites (i.e., aliphatic, aromatic and chlorinated hydrocarbons). A new pattern recognition method was developed for determining which coated sensors would maximize the selectivity and accuracy of quantitation for a given set of vapor contaminants. Using this method, an optimal subwet of four coated sensors was selected for testing in a prototype microsensor instrument. Additional laboratory experiments were performed with this optimized array to assess the limits of detection and linear response ranges for the representative vapors, as well as the additivity of responses to vapors in binary mixtures, temperature and humidity effects, aging effects, and other performance parameters related to the application of this technology to soil and groundwater VOC monitoring. Results demonstrate that SAW microsensor arrays can identify and quantify specific VOCs at concentrations in the {mu}g/L to mg/L range when present alone or in simple (e.g., binary) mixtures. SAW sensor technology offers a potentially effective alternative to existing field instrumentation for headspace analysis, soil vapor monitoring, and vacuum extraction process monitoring of VOCs in subsurface media.

Comparison of assessment methods for self-reported alcohol consumption in health interview surveys

DEFF Research Database (Denmark)

Ekholm, O; Strandberg-Larsen, K; Christensen, K

2008-01-01

To select a simple method for assessing alcohol consumption and to compare how different reference periods and response categories influence the self-reported frequency of binge drinking.......To select a simple method for assessing alcohol consumption and to compare how different reference periods and response categories influence the self-reported frequency of binge drinking....

Conflict Management Training for Peacekeepers: Assessment and Recommendations. Special Report 411

Science.gov (United States)

Milofsky, Alison; Sany, Joseph; Lancaster, Illana; Krentel, Jeff

2017-01-01

This report examines the role of conflict management training in preparing peacekeepers for United Nations/African Union missions through an assessment of the United States Institute of Peace (USIP) Conflict Management Training for Peacekeepers program. The assessment relies on data collected through 137 semistructured interviews with returned…

Mapping Priorities to Focus Cropland Mapping Activities: Fitness Assessment of Existing Global, Regional and National Cropland Maps

Directory of Open Access Journals (Sweden)

François Waldner

2015-06-01

agriculture class in order to systematically assess existing and future cropland maps.

Egypt--United States cooperative energy assessment: report on preliminary discussions

Energy Technology Data Exchange (ETDEWEB)

1978-04-01

Egyptian and U.S. Government representatives met in Cairo during the period of February 14-22, 1978 to discuss a cooperative Egypt-U.S. assessment of the energy demand and supply options available to Egypt. This report summarizes those preliminary discussions. The discussions accomplished the following: the background and objectives of the U.S. initiative for a cooperative energy assessment with Egypt were explained; Egyptian electric energy activities and their priorities were presented; methods under consideration for the systematic identification and assessment of energy options available to Egypt were explained; the cooperation of Egyptian energy resource and planning organizations was assured; and arrangements to carry out the cooperative assessment were planned.

Assessing Critical Thinking in Higher Education: Current State and Directions for Next-Generation Assessment. Research Report. ETS RR-14-10

Science.gov (United States)

Liu, Ou Lydia; Frankel, Lois; Roohr, Katrina Crotts

2014-01-01

Critical thinking is one of the most important skills deemed necessary for college graduates to become effective contributors in the global workforce. The first part of this article provides a comprehensive review of its definitions by major frameworks in higher education and the workforce, existing assessments and their psychometric qualities,…

Integrated plant safety assessment: Systematic Evaluation Program, San Onofre Nuclear Generating Station, Unit 1 (Docket No. 50-206): Final report

International Nuclear Information System (INIS)

1986-12-01

The Systematic Evaluation Program was initiated in February 1977 by the US Nuclear Regulatory Commission to review the designs of older operating nuclear reactor plants to reconfirm and document their safety. The review provides: (1) an assessment of how these plants compare with current licensing safety requirements relating to selected issues; (2) a basis for deciding on how these differences should be resolved in an integrated plant review; and (3) a documented evaluation of plant safety. This report documents the review of San Onofre Nuclear Generating Station, Unit 1, operated by Southern California Edison Company. The San Onofre plant is one of ten plants reviewed under Phase II of this program. This report indicates how 137 topics selected for review under Phase I of the program were addressed. Equipment and procedural changes have been identified as a result of the review. This report will be one of the bases in considering the issuance of a full-term operating license in place of the existing provisional operating license. This report also addresses the comments and recommendations made by the Advisory Committee on Reactor Safeguards in connection with its review of the draft report issued in April 1985

Social Protection Schemes in Pakistan: assessment of existing programs

Directory of Open Access Journals (Sweden)

Yu ShuHong

2017-07-01

Full Text Available Social protection is regarded as a basic human right guaranteed in several International Covenants and Treaties. The Constitution of Pakistan exclusively stipulates the provision of social security for all citizens of the country. The aim of the study is to explore and evaluate the social protection schemes with regards to its coverage, scope and outreach. The country has number of social security schemes that are being carried out by provincial and federal governments for the welfare of workers like old age benefits, disablement, health and medical facilities. However, these schemes have failed to extend their benefits to home based, part-time, temporary or contract and agricultural workers. This paper attempts to highlight the shortcomings of existing social protection programs that are obstructing their benefit distribution and limiting their outreach. It underlines the challenges faced by the implementing agencies. This paper also suggests some improvements in the structural design of social security mechanism with special focus on the scope, coverage, outreach and effective delivery mechanism. Since, the proper allocation of resources and effective implementation of these schemes can ensure the assistance and welfare of the targeted population.

Integrated Science Assessment (ISA) for Sulfur Oxides – Health Criteria (Final Report, Sep 2008)

Science.gov (United States)

EPA announced the availability of the final report, Integrated Science Assessment (ISA) for Sulfur Oxides – Health Criteria final assessment. This report represents a concise synthesis and evaluation of the most policy-relevant science and will ultimately provide the scien...

A scoping research literature review to assess the state of existing evidence on the "bad" death.

Science.gov (United States)

Wilson, Donna M; Hewitt, Jessica A

2018-02-01

A scoping research literature review on "bad death" was undertaken to assess the overall state of the science on this topic and to determine what evidence exists on how often bad deaths occur, what contributes to or causes a bad death, and what the outcomes and consequences of bad deaths are. A search for English-language research articles was conducted in late 2016, with 25 articles identified and all retained for examination, as is expected with scoping reviews. Only 3 of the 25 articles provided incidence information, specifying that 7.8 to 23% of deaths were bad and that bad deaths were more likely to occur in hospitals than in community-care settings. Many different factors were associated with bad deaths, with unrelieved pain being the most commonly identified. Half of the studies provided information on the possible consequences or outcomes of bad deaths, such as palliative care not being initiated, interpersonal and team conflict, and long-lasting negative community effects. This review identified a relatively small number of research articles that focused in whole or in part on bad deaths. Although the reasons why people consider a death to be bad may be highly individualized and yet also socioculturally based, unrelieved pain is a commonly held reason for bad deaths. Although bad and good deaths may have some opposing causative factors, this literature review revealed some salient bad death attributes, ones that could be avoided to prevent bad deaths from occurring. A routine assessment to allow planning so as to avoid bad deaths and enhance the probability of good deaths is suggested.

Hawaii demand-side management resource assessment. Final report, Reference Volume 1: Building prototype analysis

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-04-01

This report provides a detailed description of, and the baseline assumptions and simulation results for, the building prototype simulations conducted for the building types designated in the Work Plan for Demand-side Management Assessment of Hawaii`s Demand-Side Resources (HES-4, Phase 2). This report represents the second revision to the initial building prototype description report provided to DBEDT early in the project. Modifications and revisions to the prototypes, based on further calibration efforts and on comments received from DBEDT Staff have been incorporated into this final version. These baseline prototypes form the basis upon which the DSM measure impact estimates and the DSM measure data base were developed for this project. This report presents detailed information for each of the 17 different building prototypes developed for use with the DOE-21E program (23 buildings in total, including resorts and hotels defined separately for each island) to estimate the impact of the building technologies and measures included in this project. The remainder of this section presents some nomenclature and terminology utilized in the reports, tables, and data bases developed from this project to denote building type and vintage. Section 2 contains a more detailed discussion of the data sources, the definition of the residential sector building prototypes, and results of the DOE-2 analysis. Section 3 provides a similar discussion for the commercial sector. The prototype and baseline simulation results are presented in a separate section for each building type. Where possible, comparison of the baseline simulation results with benchmark data from the ENERGY 2020 model or other demand forecasting models specific to Hawaii is included for each building. Appendix A contains a detailed listing of the commercial sector baseline indoor lighting technologies included in the existing and new prototypes by building type.

Year 2000 assessment report, Los Alamos National Laboratory

Energy Technology Data Exchange (ETDEWEB)

Weir, D.

1998-04-21

The purpose of this report is to advise managers on the status of Year 2000 readiness at the Laboratory and provide a summary of critical issues to be addressed in order to ensure that the Year 2000 date rollover will not disrupt Laboratory Operations. The Laboratory`s Year 2000 council members are in the first phase of Year 2000 plans: gathering data and assessing the status of their divisions or programs. This first snapshot of the Laboratory Year 2000 readiness assessment is expected to grow and change over time as more refined assessments, plans, and schedules are developed and as more information becomes available. Here are findings to date: (1) Embedded systems` status not known. (2) Preliminary cost estimates for Year 2000 repairs, testing, and implementation are estimated to be at least $5.9 million, not including embedded systems. (3) The Laboratory is required to make unavoidable purchases of Year 2000-compliant products. (4) The Year 2000 short-term issue forces some long-term transition plans to be set aside. (5) The Laboratory is at risk for the following consequences if they can`t demonstrate an active Year 2000 program: risk of system failures; potential funding freezes by the OMB and DOE; legal liabilities; and risk to the UC contract. (6) The deadline for this project is immutable. (7) DOE is continually increasing reporting requirements, expanding from only DOE mission-essential to all operations. (7) DOE audit criticizes the Laboratory`s mission-essential systems planning.

FEP report for the safety assessment SR-Can

Energy Technology Data Exchange (ETDEWEB)

Skagius, Kristina [Kemakta Konsult AB, Stockholm (Sweden)

2006-11-15

This report documents the analysis and processing of features, events and processes, FEPs, that has been carried out within the safety assessment SR-Can, and forms an important part of the reporting of the project. The SR-Can project is a preparatory stage for the SR-Site assessment, and the report from that project will be used in support of SKB's application to build a final repository. The overall objective of the FEP analysis and processing included development of a database of features, events and processes, an SKB FEP database, in a format that facilitates both a systematic analysis of FEPs and documentation of that FEP analysis, as well as facilitating revisions and updates to be made in connection with new safety assessments. The overall objective also extended to the development of procedures for such a systematic FEP analysis as well as the application of those procedures in order to establish an SR-Can FEP catalogue within the framework of the SKB FEP database. The work started by implementing the content of the SR 97 Process Report into a database format suitable for import and processing of FEP information from other sources. The SR 97 version of the database was systematically audited against the NEA database with Project FEPs, version 1.2. In addition, an earlier audit of the SR 97 process report against the interaction matrices developed for a deep repository of the KBS-3 type was revisited and updated. Relevant FEPs identified through the audit process were sorted into three main categories i) FEPs related to the initial states of the repository system, ii) FEPs related to internal processes of the repository system, and iii) FEPs related to external impacts on the repository system. This resulted in additions to the SR 97 list of processes and to the lists of initial state FEPs and external factors to be addressed in further processing. The further processing of the initial state FEPs revealed that those FEPs that are not covered by the

Assessing immunization data quality from routine reports in Mozambique

Directory of Open Access Journals (Sweden)

Mavimbe João C

2005-10-01

Full Text Available Abstract Background Worldwide immunization coverage shows an increase in the past years but the validity of the official reports for measuring change over time has been questioned. Facing this problem, donor supported initiatives like the Global Alliance for Vaccine and Immunizations, have been putting a lot of effort into assessing the quality of data used, since accurate immunization information is essential for the Expanded Program on Immunization managers to track and improve program performance. The present article, discusses the practices on record keeping, reporting and the support mechanism to ensure data quality in Mozambique. Methods A process evaluation study was carried out in Mozambique in one district (Cuamba in Niassa Province, between January and March 2003. The study was based on semi-structured interviews, participant observation and review of the data collection materials. Results Differences were found for all vaccine types when comparing facility reports with the tally sheets. The same applies when comparing facility reports with district reports. The study also showed that a routine practice during supervision visits was data quality assessment for the outpatient services but none related to data consistency between the tally sheets and the facility report. For the Expanded Program on Immunization, supervisors concentrated more on the consistency checks between data in the facility reports and the number of vaccines received during the same period. Meetings were based on criticism, for example, why health workers did not reach the target. Nothing in terms of data quality was addressed nor validation rules. Conclusion In this paper we have argued that the quality of data, and consequently of the information system, must be seen in a broader perspective not focusing only on technicalities (data collection tools and the reporting system but also on support mechanisms. Implications of a poor data quality system will be

Feasibility Study of Hydrogen Production at Existing Nuclear Power Plants

Energy Technology Data Exchange (ETDEWEB)

Stephen Schey

2009-07-01

Cooperative Agreement DE-FC07-06ID14788 was executed between the U.S. Department of Energy, Electric Transportation Applications, and Idaho National Laboratory to investigate the economics of producing hydrogen by electrolysis using electricity generated by nuclear power. The work under this agreement is divided into the following four tasks: Task 1 – Produce Data and Analyses Task 2 – Economic Analysis of Large-Scale Alkaline Electrolysis Task 3 – Commercial-Scale Hydrogen Production Task 4 – Disseminate Data and Analyses. Reports exist on the prospect that utility companies may benefit from having the option to produce electricity or produce hydrogen, depending on market conditions for both. This study advances that discussion in the affirmative by providing data and suggesting further areas of study. While some reports have identified issues related to licensing hydrogen plants with nuclear plants, this study provides more specifics and could be a resource guide for further study and clarifications. At the same time, this report identifies other area of risks and uncertainties associated with hydrogen production on this scale. Suggestions for further study in some of these topics, including water availability, are included in the report. The goals and objectives of the original project description have been met. Lack of industry design for proton exchange membrane electrolysis hydrogen production facilities of this magnitude was a roadblock for a significant period. However, recent design breakthroughs have made costing this facility much more accurate. In fact, the new design information on proton exchange membrane electrolyzers scaled to the 1 kg of hydrogen per second electrolyzer reduced the model costs from $500 to $100 million. Task 1 was delayed when the original electrolyzer failed at the end of its economic life. However, additional valuable information was obtained when the new electrolyzer was installed. Products developed during this study

Reporting of Human Genome Epidemiology (HuGE association studies: An empirical assessment

Directory of Open Access Journals (Sweden)

Gwinn Marta

2008-05-01

Full Text Available Abstract Background Several thousand human genome epidemiology association studies are published every year investigating the relationship between common genetic variants and diverse phenotypes. Transparent reporting of study methods and results allows readers to better assess the validity of study findings. Here, we document reporting practices of human genome epidemiology studies. Methods Articles were randomly selected from a continuously updated database of human genome epidemiology association studies to be representative of genetic epidemiology literature. The main analysis evaluated 315 articles published in 2001–2003. For a comparative update, we evaluated 28 more recent articles published in 2006, focusing on issues that were poorly reported in 2001–2003. Results During both time periods, most studies comprised relatively small study populations and examined one or more genetic variants within a single gene. Articles were inconsistent in reporting the data needed to assess selection bias and the methods used to minimize misclassification (of the genotype, outcome, and environmental exposure or to identify population stratification. Statistical power, the use of unrelated study participants, and the use of replicate samples were reported more often in articles published during 2006 when compared with the earlier sample. Conclusion We conclude that many items needed to assess error and bias in human genome epidemiology association studies are not consistently reported. Although some improvements were seen over time, reporting guidelines and online supplemental material may help enhance the transparency of this literature.

SITE WIDE SHORT CIRCUIT STUDY ASSESSMENT

International Nuclear Information System (INIS)

CARRATT, R.T.

2004-01-01

The Department of Energy requested that Fluor Hanford develop a plan to update the electrical distribution studies for FH managed facilities. Toward this end, an assessment of FH's nuclear facilities was performed to determine whether a current short circuit study of the facility electrical distribution system exists, and the status of such study. This report presents the methodology and results of that assessment. The assessment identified 29 relevant facilities. Of these, a short circuit study could not be identified for 15 facilities. A short circuit study was found to exist for fourteen facilities, however, of these 14, four were not released into a controlled document system, and two were not performed for the entire electrical distribution system. It is recommended that for four of the facilities no further action is required based upon the limited nature of the existing electrical system, or as in the case of PFP, the status of the existing short circuit study was determined adequate. For the majority of the facilities without a short circuit study, it is recommended that one is performed, and released into a controlled document system. Two facilities require further evaluation due to missing or conflicting documentation. For the remainder of the facilities, the recommendations are to review and revise as appropriate the existing study, and release into a controlled document system. A summation of the recommendations is presented

Multimedia radionuclide exposure assessment modeling. Annual report, October 1980-September 1981

International Nuclear Information System (INIS)

Whelan, G.; Onishi, Y.; Simmons, C.S.; Horst, T.W.; Gupta, S.K.; Orgill, M.M.; Newbill, C.A.

1982-12-01

Pacific Northwest Laboratory (PNL) and Los Alamos National Laboratory (LANL) are jointly developing a methodology for assessing exposures of the air, water, and plants to radionuclides as part of an overall development effort of a radionuclide disposal site evaluation methodology. Work in FY-1981 continued the development of the Multimedia Contaminant Environmental Exposure Assessment (MCEA) methodology and initiated an assessment of radionuclide migration in Los Alamos and Pueblo Canyons, New Mexico, using the methodology. The AIRTRAN model was completed, briefly tested, and documented. In addition, a literature search for existing validation data for AIRTRAN was performed. The feasibility and advisability of including the UNSAT moisture flow model as a submodel of the terrestrial code BIOTRAN was assessed. A preliminary application of the proposed MCEA methodology, as it related to the Mortandad-South Mortandad Canyon site in New Mexico is discussed. This preliminary application represented a scaled-down version of the methodology in which only the terrestrial, overland, and surface water components were used. An update describing the progress in the assessment of radionuclide migration in Los Alamos and Pueblo Canyons is presented. 38 references, 47 figures, 11 tables

Annual report, October 1980-September 1981 Multimedia radionuclide exposure assessment modeling.

Energy Technology Data Exchange (ETDEWEB)

Whelan, G.; Onishi, Y.; Simmons, C.S.; Horst, T.W.; Gupta, S.K.; Orgill, M.M.; Newbill, C.A.

1982-12-01

Pacific Northwest Laboratory (PNL) and Los Alamos National Laboratory (LANL) are jointly developing a methodology for assessing exposures of the air, water, and plants to radionuclides as part of an overall development effort of a radionuclide disposal site evaluation methodology. Work in FY-1981 continued the development of the Multimedia Contaminant Environmental Exposure Assessment (MCEA) methodology and initiated an assessment of radionuclide migration in Los Alamos and Pueblo Canyons, New Mexico, using the methodology. The AIRTRAN model was completed, briefly tested, and documented. In addition, a literature search for existing validation data for AIRTRAN was performed. The feasibility and advisability of including the UNSAT moisture flow model as a submodel of the terrestrial code BIOTRAN was assessed. A preliminary application of the proposed MCEA methodology, as it related to the Mortandad-South Mortandad Canyon site in New Mexico is discussed. This preliminary application represented a scaled-down version of the methodology in which only the terrestrial, overland, and surface water components were used. An update describing the progress in the assessment of radionuclide migration in Los Alamos and Pueblo Canyons is presented. 38 references, 47 figures, 11 tables.

BASINs 4.0 Climate Assessment Tool (CAT): Supporting Documentation and User's Manual (Final Report)

Science.gov (United States)

EPA announced the availability of the report, BASINS 4.0 Climate Assessment Tool (CAT): Supporting Documentation and User's Manual. This report was prepared by the EPA's Global Change Research Program (GCRP), an assessment-oriented program, that sits within the Office of R...

Overview of Existing Wind Energy Ordinances

Energy Technology Data Exchange (ETDEWEB)

Oteri, F.

2008-12-01

Due to increased energy demand in the United States, rural communities with limited or no experience with wind energy now have the opportunity to become involved in this industry. Communities with good wind resources may be approached by entities with plans to develop the resource. Although these opportunities can create new revenue in the form of construction jobs and land lease payments, they also create a new responsibility on the part of local governments to ensure that ordinances will be established to aid the development of safe facilities that will be embraced by the community. The purpose of this report is to educate and engage state and local governments, as well as policymakers, about existing large wind energy ordinances. These groups will have a collection of examples to utilize when they attempt to draft a new large wind energy ordinance in a town or county without existing ordinances.

78 FR 56816 - Vidalia Onions Grown in Georgia; Change in Reporting and Assessment Requirements

Science.gov (United States)

2013-09-16

... to regulation under the order and approximately 80 onion producers in the designated production area...; FV13-955-1 FIR] Vidalia Onions Grown in Georgia; Change in Reporting and Assessment Requirements AGENCY... the reporting and assessment requirements prescribed under the marketing order for Vidalia onions...

Symptoms and side effects in chronic non-cancer pain: patient report vs. systematic assessment.

Science.gov (United States)

Jonsson, T; Christrup, L L; Højsted, J; Villesen, H H; Albjerg, T H; Ravn-Nielsen, L V; Sjøgren, P

2011-01-01

relieving distressing symptoms and managing the side effects of analgesics are essential in order to improve quality of life and functional capacity in chronic non-cancer pain patients. A quick, reliable and valid tool for assessing symptoms and side effects is needed in order to optimize treatment. We aimed to investigate the symptoms reported by chronic non-cancer pain patients after open-ended questioning vs. a systematic assessment using a list of symptoms, and to assess whether the patients could distinguish between the symptoms and the side effects induced by analgesics. patients treated with either opioids and/or adjuvant analgesics were asked to report their symptoms spontaneously, followed by a 41-item investigator-developed symptom checklist. A control group also filled in the checklist. a total of 62 patients and 64 controls participated in the study. The numbers of symptoms reported by the patients (9.9 ± 5.9) were significantly higher than those reported by the controls (3.2 ± 3.9) (Pside effects due to analgesics was: (1) Dry mouth (42%); (2) Sweating (34%); (3) Weight gain (29%); (4) Memory deficits (24%); (5) Fatigue (19%); and (6) Concentration deficits (19%). the number of symptoms reported using systematic assessment was eightfold higher than those reported voluntarily. Fatigue, cognitive dysfunction, dry mouth, sweating and weight gain were the most frequently reported. The patients reported the side effects of their analgesics to contribute substantially to the reported symptoms. 2010 The Acta Anaesthesiologica Scandinavica Foundation.

Quality of reporting in oncology phase II trials: A 5-year assessment through systematic review.

Science.gov (United States)

Langrand-Escure, Julien; Rivoirard, Romain; Oriol, Mathieu; Tinquaut, Fabien; Rancoule, Chloé; Chauvin, Frank; Magné, Nicolas; Bourmaud, Aurélie

2017-01-01

Phase II clinical trials are a cornerstone of the development in experimental treatments They work as a "filter" for phase III trials confirmation. Surprisingly the attrition ratio in Phase III trials in oncology is significantly higher than in any other medical specialty. This suggests phase II trials in oncology fail to achieve their goal. Objective The present study aims at estimating the quality of reporting in published oncology phase II clinical trials. A literature review was conducted among all phase II and phase II/III clinical trials published during a 5-year period (2010-2015). All articles electronically published by three randomly-selected oncology journals with Impact-Factors>4 were included: Journal of Clinical Oncology, Annals of Oncology and British Journal of Cancer. Quality of reporting was assessed using the Key Methodological Score. 557 articles were included. 315 trials were single-arm studies (56.6%), 193 (34.6%) were randomized and 49 (8.8%) were non-randomized multiple-arm studies. The Methodological Score was equal to 0 (lowest level), 1, 2, 3 (highest level) respectively for 22 (3.9%), 119 (21.4%), 270 (48.5%) and 146 (26.2%) articles. The primary end point is almost systematically reported (90.5%), while sample size calculation is missing in 66% of the articles. 3 variables were independently associated with reporting of a high standard: presence of statistical design (p-value <0.001), multicenter trial (p-value = 0.012), per-protocol analysis (p-value <0.001). Screening was mainly performed by a sole author. The Key Methodological Score was based on only 3 items, making grey zones difficult to translate. This literature review highlights the existence of gaps concerning the quality of reporting. It therefore raised the question of the suitability of the methodology as well as the quality of these trials, reporting being incomplete in the corresponding articles.

Quality assessment of reports on clinical trials in the Journal of Hepatology

DEFF Research Database (Denmark)

Gluud, C; Nikolova, D

1998-01-01

Electronic searches on databases for randomised clinical trials and controlled clinical trials do not identify as many trials as handsearches, and trial reporting may be flawed. The aims were to identify all fully reported randomised clinical trials in the Journal of Hepatology and to make...... a qualitative assessment of the reporting....

Paper waste - Recycling, incineration or landfilling? A review of existing life cycle assessments

International Nuclear Information System (INIS)

Villanueva, A.; Wenzel, H.

2007-01-01

A review of existing life cycle assessments (LCAs) on paper and cardboard waste has been undertaken. The objectives of the review were threefold. Firstly, to see whether a consistent message comes out of published LCA literature on optimum disposal or recycling solutions for this waste type. Such message has implications for current policy formulation on material recycling and disposal in the EU. Secondly, to identify key methodological issues of paper waste management LCAs, and enlighten the influence of such issues on the conclusions of the LCA studies. Thirdly, in light of the analysis made, to discuss whether it is at all valid to use the LCA methodology in its current development state to guide policy decisions on paper waste. A total of nine LCA studies containing altogether 73 scenarios were selected from a thorough, international literature search. The selected studies are LCAs including comparisons of different management options for waste paper. Despite claims of inconsistency, the LCAs reviewed illustrate the environmental benefits in recycling over incineration or landfill options, for paper and cardboard waste. This broad consensus was found despite differences in geographic location and definitions of the paper recycling/disposal systems studied. A systematic exploration of the LCA studies showed, however, important methodological pitfalls and sources of error, mainly concerning differences in the definition of the system boundaries. Fifteen key assumptions were identified that cover the three paper cycle system areas: raw materials and forestry, paper production, and disposal/recovery. It was found that the outcome of the individual LCA studies largely depended on the choices made in some of these assumptions, most specifically the ones concerning energy use and generation, and forestry

Peer assessment of student-produced mechanics lab report videos

Science.gov (United States)

Douglas, Scott S.; Aiken, John M.; Lin, Shih-Yin; Greco, Edwin F.; Alicea-Muñoz, Emily; Schatz, Michael F.

2017-12-01

We examine changes in students' rating behavior during a semester-long sequence of peer evaluation laboratory exercises in an introductory mechanics course. We perform a quantitative analysis of the ratings given by students to peers' physics lab reports, and conduct interviews with students. We find that peers persistently assign higher ratings to lab reports than do experts, that peers begin the semester by giving high ratings most frequently and end the semester with frequent middle ratings, and that peers go through the semester without much change in the frequency of low ratings. We then use student interviews to develop a model for student engagement with peer assessment. This model is based on two competing influences which appear to shape peer evaluation behavior: a strong disinclination to give poor ratings with a complementary preference to give high ratings when in doubt, and an attempt to develop an expertlike criticality when assessing peers' work.

Peer assessment of student-produced mechanics lab report videos

Directory of Open Access Journals (Sweden)

Scott S. Douglas

2017-11-01

Full Text Available We examine changes in students’ rating behavior during a semester-long sequence of peer evaluation laboratory exercises in an introductory mechanics course. We perform a quantitative analysis of the ratings given by students to peers’ physics lab reports, and conduct interviews with students. We find that peers persistently assign higher ratings to lab reports than do experts, that peers begin the semester by giving high ratings most frequently and end the semester with frequent middle ratings, and that peers go through the semester without much change in the frequency of low ratings. We then use student interviews to develop a model for student engagement with peer assessment. This model is based on two competing influences which appear to shape peer evaluation behavior: a strong disinclination to give poor ratings with a complementary preference to give high ratings when in doubt, and an attempt to develop an expertlike criticality when assessing peers’ work.

Integrated safety assessment report, Haddam Neck Plant (Docket No. 50-213): Integrated Safety Assessment Program: Draft report

International Nuclear Information System (INIS)

1987-07-01

The integrated assessment is conducted on a plant-specific basis to evaluate all licensing actions, licensee initiated plant improvements and selected unresolved generic/safety issues to establish implementation schedules for each item. Procedures allow for a periodic updating of the schedules to account for licensing issues that arise in the future. The Haddam Neck Plant is one of two plants being reviewed under the pilot program. This report indicates how 82 topics selected for review were addressed, and presents the staff's recommendations regarding the corrective actions to resolve the 82 topics and other actions to enhance plant safety. 135 refs., 4 figs., 5 tabs

Television for Effective Parenthood; Literature Search and Existing Materials Assessment.

Science.gov (United States)

Appalachia Educational Lab., Charleston, WV.

Materials concerning parenthood education were assessed and classified as published research, audiovisual materials, and pamphlets and booklets. Eighty-nine items of related research were reviewed and listed in a bibliography. Content and technical quality of audiovisual materials from a national search were reviewed and evaluated based on…

Regulatory Approaches for Adding Capacity to Existing Hydropower Facilities

Energy Technology Data Exchange (ETDEWEB)

Levine, Aaron L. [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Curtis, Taylor L. [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Kazerooni, Borna [National Renewable Energy Laboratory (NREL), Golden, CO (United States)

2017-10-24

In 2015, hydroelectric generation accounted for more than 6 percent of total net electricity generation in the United States and 46 percent of electricity generation from all renewables. The United States has considerable hydroelectric potential beyond what is already being developed. Nearly 7 GW of this potential is found by adding capacity to existing hydropower facilities. To optimize the value of hydroelectric generation, the U.S. Department of Energy's Hydropower Vision Study highlights the importance of adding capacity to existing facilities. This report provides strategic approaches and considerations for Federal Energy Regulatory Commission licensed and exempt hydropower facilities seeking to increase generation capacity, which may include increases from efficiency upgrades. The regulatory approaches reviewed for this report include capacity and non-capacity amendments, adding capacity during relicensing, and adding capacity when converting a license to a 10-MW exemption.

Accuracy of self-reported tobacco assessments in a head and neck cancer treatment population

International Nuclear Information System (INIS)

Warren, Graham W.; Arnold, Susanne M.; Valentino, Joseph P.; Gal, Thomas J.; Hyland, Andrew J.; Singh, Anurag K.; Rangnekar, Vivek M.; Cummings, K. Michael; Marshall, James R.; Kudrimoti, Mahesh R.

2012-01-01

Prospective analysis was performed of self-reported and biochemically confirmed tobacco use in 50 head and neck cancer patients during treatment. With 93.5% compliance to complete weekly self-report and biochemical confirmatory tests, 29.4% of smokers required biochemical assessment for identification. Accuracy increased by 14.9% with weekly vs. baseline self-reported assessments. Data confirm that head and neck cancer patients misrepresent true tobacco use during treatment.

Final Systems Development Report for the Clark County Socioeconomic Impact Assessment of the Proposed High-Level Nuclear Waste Repository at Yucca Mountain, NV

Energy Technology Data Exchange (ETDEWEB)

NONE

1992-06-18

The Systems Development Report represents the third major step in the Clark County Socioeconomic Impact Assessment of the Proposed High-Level Nuclear Waste Repository at Yucca Mound Nevada. The first of these steps was to forge a Research Design that would serve as a guide for the overall research process. The second step was the construction of the Base Case, the purpose of which was to describe existing conditions in Clark County in the specified analytic areas of Economic-Demographic/Fiscal, Emergency Planning and Management, Transportation and Sociocultural analysis. The base case description will serve as a basis for assessing changes in these topic areas that might result from the Yucca Mountain project. These changes will be assessed by analyzing conditions with and without repository development in the county. Prior to performing such assessments, however, the snapshot type of data found in the base case must be operationalized or systematized to allow for more dynamic data utilization. In other words, a data system that can be used to analyze the consequences of the introduction of different variables (or variable values) in the Clark County context must be constructed. Such a system must be capable of being updated through subsequent data collection and monitoring efforts to both provide a rolling base case and supply information necessary to construct trend analyses. For example, during the Impact Assessment phase of the study process, the without repository analysis is accomplished by analyzing growth for the county given existing conditions and likely trends. These data are then compared to the with Yucca Mountain project conditions anticipated for the county. Similarly, once the emergency planning management and response needs associated with the repository are described, these needs will be juxtaposed against existing (and various future) capacity(ies) in order to determine the nature and magnitude of impacts in this analytic area. Analogous tasks

Seismic assessment of Technical Area V (TA-V).

Energy Technology Data Exchange (ETDEWEB)

Medrano, Carlos S.

2014-03-01

The Technical Area V (TA-V) Seismic Assessment Report was commissioned as part of Sandia National Laboratories (SNL) Self Assessment Requirement per DOE O 414.1, Quality Assurance, for seismic impact on existing facilities at Technical Area-V (TA-V). SNL TA-V facilities are located on an existing Uniform Building Code (UBC) Seismic Zone IIB Site within the physical boundary of the Kirtland Air Force Base (KAFB). The document delineates a summary of the existing facilities with their safety-significant structure, system and components, identifies DOE Guidance, conceptual framework, past assessments and the present Geological and Seismic conditions. Building upon the past information and the evolution of the new seismic design criteria, the document discusses the potential impact of the new standards and provides recommendations based upon the current International Building Code (IBC) per DOE O 420.1B, Facility Safety and DOE G 420.1-2, Guide for the Mitigation of Natural Phenomena Hazards for DOE Nuclear Facilities and Non-Nuclear Facilities.

Patient reported facial scar assessment: directions for the professional

NARCIS (Netherlands)

Hoogewerf, C.J.; van Baar, M.E.; Middelkoop, E.; van Loey, N.E.

2014-01-01

Background The face is central to our identity and provides our most expressive means of communication. Currently, the role of facial scarring in relation to self-esteem is unclear and the value of self-reported scar assessment is insufficiently understood. The aim of this study was twofold: (1) to

Patient reported facial scar assessment : directions for the professional

NARCIS (Netherlands)

Hoogewerf, Cornelis J; van Baar, Margriet E; Middelkoop, Esther; Van Loey, N.E.E.

BACKGROUND: The face is central to our identity and provides our most expressive means of communication. Currently, the role of facial scarring in relation to self-esteem is unclear and the value of self-reported scar assessment is insufficiently understood. The aim of this study was twofold: (1) to

Sustainability assessment of renewable energy projects: research report

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-07-01

This report describes the results of a study that examined the development of an appraisal framework for renewable energy projects in the UK. The aim was to develop a framework that reflected the quality of life capital approach and could take into account social, economic and environmental effects at a range of different scales. The report describes in some detail: the steps leading to the definition, refinement and testing of the appraisal framework; the assessment methodology; baseline characterisation and evaluation; and application. Three fictional case studies (wind farm in a remote upland rural area, energy recovery facility in an urban fringe location and wood fuelled renewable energy plant in less remote rural area) are used to test the approach.

Operating experience feedback report: Assessment of spent fuel cooling. Volume 12

International Nuclear Information System (INIS)

Ibarra, J.G.; Jones, W.R.; Lanik, G.F.; Ornstein, H.L.; Pullani, S.V.

1997-02-01

This report documents the results of an independent assessment by a team from the Office of Analysis and Evaluation of Operational Data of spent-fuel-pool (SFP) cooling in operating nuclear power plants. The team assessed the likelihood and consequences of an extended loss of SFP cooling and suggested corrective actions, based on their findings

[Does the right to die with dignity exist?].

Science.gov (United States)

Toro Flores, Rafael

2008-12-01

Death is one of the few certainties in human beings. This reality generates uneasiness regarding how death will occur especially in circumstances of loneliness or suffering which can become agony. In this report, the author first analyzes the existence of the right to die with dignity as a human right which takes on the nature of being a subjective right. In continuation, the author describes the existing problematic in the application of this right to die in relationship to the so-called double effect mechanism and euthanasia. The author concludes this article by proposing previous instructions or anticipated desires as ideal measures to make the right to die with dignity valid.

Reliability of the Music in Everyday Life (MEL) Scale: A Parent-Report Assessment for Children on the Autism Spectrum.

Science.gov (United States)

Gottfried, Tali; Thompson, Grace; Elefant, Cochavit; Gold, Christian

2018-06-07

For young children on the autism spectrum, the inclusion of shared parent-child music activities in everyday life may provide additional opportunities for social interactions in the home. However, no psychometrically validated assessment exists to measure the extent of shared music activity within family or community contexts. This study aimed to develop and test the reliability of a self-report assessment to measure the use of Music in Everyday Life (MEL) by parents with young children on the autism spectrum. A total of 45 mothers of children with autism aged between 4 and 7 years completed the MEL questionnaire. Internal consistency and item-total correlation were examined. Analysis confirmed the reliability of two predetermined subscales: Music in Everyday Life-Joint Activities using Music (MEL-JAM) and Music in Everyday Life-Routine Activities using Music (MEL-RAM). Internal consistency (Cronbach's alpha 0.63 and 0.75) and positive item-total correlation (Pearson's r between .23 to .62 for MEL-JAM and between .30 to .67 for MEL-RAM) were demonstrated. The reliability of the MEL assessment to measure the use of music in everyday life by parents with their children with autism was confirmed, filling an important gap in the availability of assessment tools.

Environmental Hazards Assessment Program: Annual report, July 1, 1995--June 30, 1996

International Nuclear Information System (INIS)

1996-01-01

The objectives of the Environmental Hazards Assessment Program (EHAP) are to: (1) develop a holistic, national basis for risk assessment, risk management, and risk communication that recognizes the direct impact of environmental hazards on the health and well-being of all; (2) develop a pool of talented scientists and experts in cleanup activities, especially in human health aspects; and (3) identify needs and develop programs addressing the critical shortage of well-educated, highly-skilled technical and scientific personnel to address the health-oriented aspects of environmental restoration and waste management. This report describes activities and reports on progress for the fourth year of the grant. It reports progress against these grant objectives and the Program Implementation Plan

Pre-existing and Postoperative Intimal Hyperplasia and Arteriovenous Fistula Outcomes.

Science.gov (United States)

Tabbara, Marwan; Duque, Juan C; Martinez, Laisel; Escobar, Luis A; Wu, Wensong; Pan, Yue; Fernandez, Natasha; Velazquez, Omaida C; Jaimes, Edgar A; Salman, Loay H; Vazquez-Padron, Roberto I

2016-09-01

The contribution of intimal hyperplasia (IH) to arteriovenous fistula (AVF) failure is uncertain. This observational study assessed the relationship between pre-existing, postoperative, and change in IH over time and AVF outcomes. Prospective cohort study with longitudinal assessment of IH at the time of AVF creation (pre-existing) and transposition (postoperative). Patients were followed up for up to 3.3 years. 96 patients from a single center who underwent AVF surgery initially planned as a 2-stage procedure. Veins and AVF samples were collected from 66 and 86 patients, respectively. Matched-pair tissues were available from 56 of these patients. Pre-existing, postoperative, and change in IH over time. Anatomic maturation failure was defined as an AVF that never reached a diameter > 6mm. Primary unassisted patency was defined as the time elapsed from the second-stage surgery to the first intervention. Maximal intimal thickness in veins and AVFs and change in intimal thickness over time. Pre-existing IH (>0.05mm) was present in 98% of patients. In this group, the median intimal thickness increased 4.40-fold (IQR, 2.17- to 4.94-fold) between AVF creation and transposition. However, this change was not associated with pre-existing thickness (r(2)=0.002; P=0.7). Ten of 96 (10%) AVFs never achieved maturation, whereas 70% of vascular accesses remained patent at the end of the observational period. Postoperative IH was not associated with anatomic maturation failure using univariate logistic regression. Pre-existing, postoperative, and change in IH over time had no effects on primary unassisted patency. The small number of patients from whom longitudinal tissue samples were available and low incidence of anatomic maturation failure, which decreased the statistical power to find associations between end points and IH. Pre-existing, postoperative, and change in IH over time were not associated with 2-stage AVF outcomes. Copyright © 2016 National Kidney Foundation, Inc

Creation of a Risk Assessment Methodology

OpenAIRE

Lefebvre, Nicolas

2007-01-01

This report is a presentation of the work realised during an internship at the consultancy division of Thales Security Systems from September 2005 to June 2006. Thales Security Systems is part of Thales, an international group in defence, aeronautics, etc. The work realised consisted in the creation of a new risk assessment methodology for a commercial offer called HELP, standing for Human, Environmental, Logical and Physical security. As a basis for the work, 5 existing risk assessment metho...

The self assessment at ANGRA 1 NPP in Brazil

International Nuclear Information System (INIS)

Werdine, H. Jr.

1996-01-01

Angra 1 considers the Self-Assessment concept an extremely valuable tool to enhance plant safety and plant performance. A formal guidance procedure to apply this methodology does not exist at our plant and should be developed and implemented as soon as possible. Some portions of this methodology already exist with different names. The root cause analysis of in-house incident reports is a heavy portion of a sound self-assessment approach. International related experience from top performance plants should be used. International meetings, such as this one, should be convened and formal guidance from the IAEA should be written

The self assessment at ANGRA 1 NPP in Brazil

Energy Technology Data Exchange (ETDEWEB)

Werdine, H Jr [Furnas Centrais Eletricas S.A., Rio de Janeiro (Brazil)

1997-12-31

Angra 1 considers the Self-Assessment concept an extremely valuable tool to enhance plant safety and plant performance. A formal guidance procedure to apply this methodology does not exist at our plant and should be developed and implemented as soon as possible. Some portions of this methodology already exist with different names. The root cause analysis of in-house incident reports is a heavy portion of a sound self-assessment approach. International related experience from top performance plants should be used. International meetings, such as this one, should be convened and formal guidance from the IAEA should be written.

Performance assessment task team progress report

International Nuclear Information System (INIS)

Wood, D.E.; Curl, R.U.; Armstrong, D.R.; Cook, J.R.; Dolenc, M.R.; Kocher, D.C.; Owens, K.W.; Regnier, E.P.; Roles, G.W.; Seitz, R.R.

1994-05-01

The U.S. Department of Energy (DOE) Headquarters EM-35, established a Performance Assessment Task Team (referred to as the Team) to integrate the activities of the sites that are preparing performance assessments (PAs) for disposal of new low-level waste, as required by Chapter III of DOE Order 5820.2A, open-quotes Low-Level Waste Managementclose quotes. The intent of the Team is to achieve a degree of consistency among these PAs as the analyses proceed at the disposal sites. The Team's purpose is to recommend policy and guidance to the DOE on issues that impact the PAs, including release scenarios and parameters, so that the approaches are as consistent as possible across the DOE complex. The Team has identified issues requiring attention and developed discussion papers for those issues. Some issues have been completed, and the recommendations are provided in this document. Other issues are still being discussed, and the status summaries are provided in this document. A major initiative was to establish a subteam to develop a set of test scenarios and parameters for benchmarking codes in use at the various sites. The activities of the Team are reported here through December 1993

Are existing outcome instruments suitable for assessment of spinal trauma patients?

Science.gov (United States)

Stadhouder, Agnita; Buckens, Constantinus F M; Holtslag, Herman R; Oner, F Cumhur

2010-11-01

Valid outcome assessment tools specific for spinal trauma patients are necessary to establish the efficacy of different treatment options. So far, no validated specific outcome measures are available for this patient population. The purpose of this study was to assess the current state of outcome measurement in spinal trauma patients and to address the question of whether this group is adequately served by current disease-specific and generic health-related quality-of-life instruments. A number of widely used outcome measures deemed most appropriate were reviewed, and their applicability to spinal trauma outcome discussed. An overview of recent movements in the theoretical foundations of outcome assessment, as it pertains to spinal trauma patients has been attempted, along with a discussion of domains important for spinal trauma. Commonly used outcome measures that are recommended for use in trauma patients were reviewed from the perspective of spinal trauma. The authors further sought to select a number of spine trauma-relevant domains from the WHO's comprehensive International Classification of Functioning, Disability and Health (ICF) as a benchmark for assessing the content coverage of the commonly used outcome measurements reviewed. The study showed that there are no psychometrically validated outcome measurements for the spinal trauma population and there are no commonly used outcome measures that provide adequate content coverage for spinal trauma domains. Spinal trauma patients are currently followed either as a subset of the polytrauma population in the acute and early postacute setting or as a subset of neurological injury in the long-term revalidation medicine setting.

Synthesis report of geo technic assessment to clay-AGP design: reference concept

International Nuclear Information System (INIS)

Farina, P.; Pedraza, L.; Ruiz, F.

1995-01-01

This report summarizes the studies on clays for the storage of radioactive wastes. The study is focussed to the geotechnical assessment for the clays. The report presents the methodology analysis, the geotechnical feasibility, minimizing methods, costs and operation

Green report. Report on the status of forestry in the Slovak Republic 2007

International Nuclear Information System (INIS)

Moravcik, M.

2007-08-01

The report evaluates the most recent developments in Slovak forestry and provides a wide range of economic, social and environmental data associated with the sector. As in previous years, the report is indicative of developmental trends allowing us to assess the nature and appropriateness of measures aimed at sustainable management of forest resources. The report highlights a number of issues which clearly support the fact that forest managers at present primarily focus on the preservation of the existing forest biodiversity and the fulfilment of all forest functions in order to satisfy multiple needs of the contemporary society. Most importantly, they strive in their efforts to secure rightful needs of future generations

Green report. Report on the status of forestry in the Slovak Republic 2007

Energy Technology Data Exchange (ETDEWEB)

Moravcik, M [National Forest Center. Forest Research Institute, Zvolen (Slovakia)

2007-08-15

The report evaluates the most recent developments in Slovak forestry and provides a wide range of economic, social and environmental data associated with the sector. As in previous years, the report is indicative of developmental trends allowing us to assess the nature and appropriateness of measures aimed at sustainable management of forest resources. The report highlights a number of issues which clearly support the fact that forest managers at present primarily focus on the preservation of the existing forest biodiversity and the fulfilment of all forest functions in order to satisfy multiple needs of the contemporary society. Most importantly, they strive in their efforts to secure rightful needs of future generations.

Updating Assessment Styles: Website Development Rather than Report Writing for Project Based Learning Courses

Science.gov (United States)

Brown, Nicola

2017-01-01

While teaching methods tend to be updated frequently, the implementation of new innovative assessment tools is much slower. For example project based learning has become popular as a teaching technique, however, the assessment tends to be via traditional reports. This paper reports on the implementation and evaluation of using website development…

Assessment and Rehabilitation Issues Concerning Existing 70’s Structural Stock

Science.gov (United States)

Sabareanu, E.

2017-06-01

The last 30 years were very demanding in terms of norms and standards change concerning the structural calculus for buildings, leaving a large stock of structures erected during 70-90 decades in a weak position concerning seismic loads and loads level for live loads, wind and snow. In the same time, taking into account that a large amount of buildings are in service all over the country, they cannot be demolished, but suitable rehabilitation methods should be proposed, structural durability being achieved. The paper proposes some rehabilitation methods suitable in terms of structural safety and cost optimization for diaphragm reinforced concrete structures, with an example on an existing multi storey building.

Life Cycle Assessment - Theory and Practice

DEFF Research Database (Denmark)

This book is a uniquely pedagogical while still comprehensive state-of-the-art description of LCA-methodology and its broad range of applications. The five parts of the book conveniently provide: I) the history and context of Life Cycle Assessment (LCA) with its central role as quantitative and s...... needed to perform an LCA. V) An appendix with an LCA report template, a full example LCA report serving as inspiration for students who write their first LCA report, and a more detailed overview of existing LCIA methods and their similarities and differences....

Taking Stock: Existing Resources for Assessing a New Vision of Science Learning

Science.gov (United States)

Alonzo, Alicia C.; Ke, Li

2016-01-01

A new vision of science learning described in the "Next Generation Science Standards"--particularly the science and engineering practices and their integration with content--pose significant challenges for large-scale assessment. This article explores what might be learned from advances in large-scale science assessment and…

Review of existing residential energy efficiency certification and rating programs

Energy Technology Data Exchange (ETDEWEB)

Hendrickson, P.L.

1986-11-01

This report was prepared for the Office of Buildings and Community Systems, US Department of Energy (DOE). The principal objective of the report is to present information on existing Home Energy Rating Systems (HERS) and their features. Much of the information in this report updates a 1982 report (PNL-4359), also prepared by the Pacific Northwest Laboratory (PNL) for DOE. Secondary objectives of the report are to qualitatively examine the benefits and costs of HERS programs, review survey results on the attitudes of various user groups toward the programs, and discuss selected design and implementation issues.

Nuclear Criticality Safety Assessment for Tank 38H Salt Dissolution

International Nuclear Information System (INIS)

Davis, P.L.

1996-01-01

This assessment report of sample results of the accumulating insoluble solids from Tank 38H demonstrates that an inherent subcritical condition for nuclear criticality safety exists during saltcake dissolution. This report also defines criteria for future sampling of Tank 38H for continued verification of the inherent subcritical condition as saltcake dissolution proceeds

Contract 98, Appendix F self-assessment report for Fiscal Year 2003

Energy Technology Data Exchange (ETDEWEB)

Albert (Editor), Rich

2003-10-15

This report summarizes the Ernest Orlando Lawrence Berkeley National Laboratory internal assessment of Laboratory operational and administrative performance in key support functions for Fiscal Year (FY) 2003. The report provides documentation of ongoing performance-based management and oversight processes required by the Department of Energy (DOE) to monitor, measure, and evaluate Berkeley Lab work.

Needs assessment activity report: Fiscal year 1995

International Nuclear Information System (INIS)

1995-09-01

The Needs Assessment program has assessed the packaging requirements of many U.S. Department of Energy (DOE) sites. These assessments have involved site visits and meetings with personnel involved with transportation and packaging of hazardous materials. By September 1995, 24 DOE facilities had been visited, with 14 site visits occurring in fiscal year 1995. As a result, these sites have been informed of some of the packaging activities that DOE has sponsored and is sponsoring, have been apprised of the affects of upcoming changes to transportation regulations, have discussed their near-term packaging needs, and have shared unique packaging they have developed, which may be of use to other DOE facilities. Program successes include discovery of a need for a reusable Type A liquid sample packaging and its development within another DOE task and establishing communications pathways between DOE sites that have similar transportation and packaging needs. This report recommends that the Needs Assessment activity continue to pursue the strategy of visiting DOE sites to meet with their transportation and packaging personnel. These visits will ensure that DOE needs are met, communications pathways between DOE sites are established and cultivated, and redundant packaging development is identified. The site visits should be expanded to include meetings with the long-range and strategic planners at each site, and at the DOE-Headquarters level, to ensure that all future transportation and packaging needs are identified early enough to allow adequate transportation assessment and packaging development. This activity could become a permanent conduit for information and will ensure that all future DOE transportation and packaging needs are satisfied in a cost-effective, timely, and efficient manner

Indicators assessing the performance of renewable energy support policies in 27 Member States. D17 Report

Energy Technology Data Exchange (ETDEWEB)

Steinhilber, S.; Ragwitz, M. [Fraunhofer Institute for Systems and Innovation Research ISI, Karlsruhe (Germany); Rathmann, M.; Klessmann, C.; Noothout, P. [Ecofys, Utrecht (Netherlands)

2011-10-15

The core objective of the RE-Shaping project is to assist Member State governments in preparing for the implementation of Directive 2009/28/EC (on the promotion of the use of energy from renewable sources) and to guide a European policy for RES (renewable energy sources) in the mid- to long term. The past and present success of policies for renewable energies will be evaluated and recommendations derived to improve future RES support schemes. The core content of this collaborative research activity comprises: Developing a comprehensive policy background for RES support instruments; Providing the European Commission and Member States with scientifically based and statistically robust indicators to measure the success of currently implemented RES policies; Proposing innovative financing schemes for lower costs and better capital availability in RES financing; Initiation of National Policy Processes which attempt to stimulate debate and offer key stakeholders a meeting place to set and implement RES targets as well as options to improve the national policies fostering RES market penetration; Assessing options to coordinate or even gradually harmonize national RES policy approaches. It is the objective of this report to assess the performance of Member States in promoting renewable energy technologies (RET) that has been achieved during recent years. The report was originally published in late 2010 and has now been updated using the latest available data. The focus shall be on the following aspects: Monitoring the historic success of RET-support with quantitative indicators; Extension of existing Policy Effectiveness Indicator and economic indicators; New: Deployment Status Indicator and Electricity Market Preparedness indicator; followed by Conclusions and recommendations.

Measure Guideline: Selecting Ventilation Systems for Existing Homes

Energy Technology Data Exchange (ETDEWEB)

Aldrich, R. [Consortium for Advanced Residential Buildings (CARB), Norwalk, CT (United States)

2014-02-01

This report, developed by Building America research team CARB, addresses adding or improving mechanical ventilation systems to existing homes. The goal of this report is to assist decision makers and contractors in making informed decisions when selecting ventilation systems for homes. With more air-sealed envelopes, a mechanical means of removing contaminants is critical for indoor environmental quality and building durability. The purpose of ventilation is to remove contaminants from homes, and this report discusses where, when, and how much ventilation is appropriate in a home, including examination of relevant codes and standards. Choosing the "best" system is not always straightforward; selecting a system involves balancing performance, efficiency, cost, required maintenance, and several other factors.

Risk communication for existing exposure situation after the nuclear disaster

International Nuclear Information System (INIS)

Yamaguchi, Ichiro

2011-01-01

The title subject is explained for its better understanding and recognition. The present state (Oct. 2011) where crisis of Fukushima Nuclear Accident has reached a settlement with release of 0.1 GBq/hr from the reactor container, is called the existing exposure situation. Radiation risk must be reduced under such a situation as people have to live in. Risk is defined to be a probability of matters undesirable, its size is assessed by various conditions and assumptions, it is manageable on its assessment, but its realization largely depends on subjectivity. Measures for lessening the risk usually accompany a load and disadvantage, leading to an antinomy structure (trade-off), of which problem is ultimately an ethical task of public health and cannot be solved in the form everybody agrees with. Therefore, a mutual consent among concerned people is required for deciding the principle of the risk management, for which the risk communication is essential. Risk communication about radiation is an unavoidable task of medical staffs as guided by International Commission of Radiological Protection (ICRP) (2001), International Atomic Energy Agency (IAEA) (2008) reports, World Health Organization (WHO), etc. However, the communication about radiation has now become also a task of the ordinary public under the present situation. For this, medical staffs are expected to play their role by acquiring the statistical literacy as well as with the radiological concept because the risk assessment accompanies the uncertainty. The author concludes that the risk communication is a problem of resolution to act, not of coping with. (T.T.)

Riel Converter Station, Winnipeg: Site selection and environmental assessment status report

International Nuclear Information System (INIS)

1991-01-01

As part of its expansion plans, Manitoba Hydro is planning to construct a converter station east of Winnipeg to receive power from a 850-km dc transmission line which will be constructed to bring power from a new generating station in the north of the province. Work performed to date on site selection and preliminary environmental assessment of the converter station is reviewed. The role of the converter station is described and the potential impacts are summarized in such areas as employment opportunities, pollution and noise during construction, electric and magnetic field effects, and land use impacts. Site selection criteria are outlined and potential sites are identified and evaluated. The Deacon site has been chosen as the preferred site since it has a number of inherent advantages including existing ownership by Manitoba Hydro, proximity to existing transmission rights-of-way, and low visual and land-use impact. 12 figs

BASINs and WEPP Climate Assessment Tools (CAT): Case Study Guide to Potential Applications (Final Report)

Science.gov (United States)

EPA announced the release of the final report, BASINs and WEPP Climate Assessment Tools (CAT): Case Study Guide to Potential Applications. This report supports application of two recently developed water modeling tools, the Better Assessment Science Integrating point & ...

Risk assessment for produced water discharges to Louisiana open bays. Final report

International Nuclear Information System (INIS)

Meinhold, A.F.; DePhillips, M.P.; Holtzman, S.

1996-01-01

The US Department of Energy (USDOE) has a program of research in the environmental aspects of oil and gas extraction. This sampling project will characterize the environmental impacts associated with the discharge of naturally occurring radioactive materials (NORM), metals and organics in produced water. This report is part of a series of studies of the health and ecological risks from discharges of produced water to the Gulf of Mexico, supported by the USDOE. These assessments are being coordinated with the field study, using the collected data to perform human health and ecological risk assessments. These assessments will provide input to regulators in the development of guidelines and permits, and to industry in the development and use of appropriate discharge practices. The initial human health and ecological risk assessments consist of conservative screening analyses meant to identify potentially important contaminants, and to eliminate others from further consideration. More quantitative assessments were done for contaminants identified, in the screening analysis, as being of potential concern. Section 2 gives an overview of human health and ecological risk assessment to help put the analyses presented here in perspective. Section 3 provides the hazard assessment portion of the risk assessment, and identifies the important receptors and pathways of concern. Section 3 also outlines the approach taken to the risk assessments presented in the rest of the report. The remaining sections (4 through 9) present the human health and ecological risk assessments for discharges of produced water to open bays in Louisiana

Accurate assessment of adherence: self-report and clinician report vs electronic monitoring of nebulizers.

Science.gov (United States)

Daniels, Tracey; Goodacre, Lynne; Sutton, Chris; Pollard, Kim; Conway, Steven; Peckham, Daniel

2011-08-01

People with cystic fibrosis have a high treatment burden. While uncertainty remains about individual patient level of adherence to medication, treatment regimens are difficult to tailor, and interventions are difficult to evaluate. Self- and clinician-reported measures are routinely used despite criticism that they overestimate adherence. This study assessed agreement between rates of adherence to prescribed nebulizer treatments when measured by self-report, clinician report, and electronic monitoring suitable for long-term use. Seventy-eight adults with cystic fibrosis were questioned about their adherence to prescribed nebulizer treatments over the previous 3 months. Self-report was compared with clinician report and stored adherence data downloaded from the I-Neb nebulizer system. Adherence measures were expressed as a percentage of the prescribed regimen, bias was estimated by the paired difference in mean (95% CI) patient and clinician reported and actual adherence. Agreement between adherence measures was calculated using intraclass correlation coefficients (95% CI), and disagreements for individuals were displayed using Bland-Altman plots. Patient-identified prescriptions matched the medical record prescription. Median self-reported adherence was 80% (interquartile range, 60%-95%), whereas median adherence measured by nebulizer download was 36% (interquartile range, 5%-84.5%). Nine participants overmedicated and underreported adherence. Median clinician report ranged from 50% to 60%, depending on profession. Extensive discrepancies between self-report and clinician report compared with nebulizer download were identified for individuals. Self- and clinician-reporting of adherence does not provide accurate measurement of adherence when compared with electronic monitoring. Using inaccurate measures has implications for treatment burden, clinician prescribing practices, cost, and accuracy of trial data.

Groundwater impact assessment report for the 216-Z-20 Crib, 200 West Area

International Nuclear Information System (INIS)

Johnson, V.G.

1993-10-01

As required by the Hanford Federal Facility Agreement and Consent Order ([Tri-Party Agreement] Milestone M-17-00A), this report assesses the impact of wastewater discharges to the 216-Z-20 Crib on groundwater quality. The assessment reported herein extends the initial analysis conducted from 1989 through 1990 for the Liquid Effluent Study Final Project Report. Three primary issues are addressed in response to regulator concerns with the initial analysis: The magnitude and status of the soil column transuranic inventory. Potential interactions of wastewater with carbon tetrachloride from adjacent facilities. Preferential pathways created by unsealed monitoring wells

Groundwater impact assessment report for the 216-Z-20 Crib, 200 West Area

Energy Technology Data Exchange (ETDEWEB)

Johnson, V.G.

1993-10-01

As required by the Hanford Federal Facility Agreement and Consent Order ([Tri-Party Agreement] Milestone M-17-00A), this report assesses the impact of wastewater discharges to the 216-Z-20 Crib on groundwater quality. The assessment reported herein extends the initial analysis conducted from 1989 through 1990 for the Liquid Effluent Study Final Project Report. Three primary issues are addressed in response to regulator concerns with the initial analysis: The magnitude and status of the soil column transuranic inventory. Potential interactions of wastewater with carbon tetrachloride from adjacent facilities. Preferential pathways created by unsealed monitoring wells.

Interest and limitations of projective techniques in the assessment of personality disorders.

Science.gov (United States)

Petot, J M

2000-06-01

Assessing personality disorders (PD) remains a difficult task because of persistent problems linked to concurrent validity of existing instruments, which are all structured interviews or self-report inventories. It has been advocated that indirect methods, projective techniques in particular, can strengthen PD assessment methods. The thematic apperception test (TAT) may be a significant adjuvant method of PD assessment.

IWGT report on quantitative approaches to genotoxicity risk assessment II. Use of point-of-departure (PoD) metrics in defining acceptable exposure limits and assessing human risk.