WorldWideScience

Sample records for repaired fiber-reinforced composite

  1. A Fully Contained Resin Infusion Process for Fiber-Reinforced Polymer Composite Fabrication and Repair

    Science.gov (United States)

    2013-01-01

    Assisted Resin Transfer Molding ( VARTM ) process is applicable for fiber-reinforced polymer (FRP) composite fabrication and repair. However, VARTM in...scenario is a fully enclosed VARTM system that limits the need for laboratory or manufacturing equipment. The Bladder-Bag VARTM (BBVARTM) technique...composite fabrication, VARTM , composite repair, in-field repair 16. SECURITY CLASSIFICATION OF: 17. LIMITATION OF ABSTRACT UU 18. NUMBER

  2. A fiber-reinforced composite structure for the repair of thermally cracked bituminous pavements

    Science.gov (United States)

    Frantzen, Jeffrey Alan

    1998-10-01

    The apparatus under development in this project is a structural component or beam fabricated from a fiber reinforced plastic composite (FRPC). The FRPC beam is a structural repair component intended to bridge a deteriorated thermal crack in full depth bituminous pavements or partial depth bituminous pavements over portland cement concrete. The bridging action provided by the FRPC beam is intended to minimize roughness through the repaired area for up to five years, eliminate reappearance of the deteriorated crack, and provide a controlled expansion crack that can be treated with standard sealing techniques. This apparatus is designed for maintenance use as a field expedient, semi-permanent repair using tools that are commonly available at the Area Maintenance level. Three FRPC beams were constructed for field trial in a thermally cracked, full depth bituminous pavement on US-36 east of Hiawatha, Kansas. Each of the beams were instrumented with bonded metal foil strain gages and field installation by KDOT Maintenance forces was done in August and September of 1997. The FRPC beams have been evaluated since installation and this evaluation will continue for up to five years. Evaluation of the beams has been accomplished through static load tests using the strain gage instrumentation and Falling Weight Deflectometer measurements. The FRPC beams have performed satisfactorily as of the date of writing.

  3. Machining of fiber reinforced composites

    Science.gov (United States)

    Komanduri, Ranga; Zhang, Bi; Vissa, Chandra M.

    Factors involved in machining of fiber-reinforced composites are reviewed. Consideration is given to properties of composites reinforced with boron filaments, glass fibers, aramid fibers, carbon fibers, and silicon carbide fibers and to polymer (organic) matrix composites, metal matrix composites, and ceramic matrix composites, as well as to the processes used in conventional machining of boron-titanium composites and of composites reinforced by each of these fibers. Particular attention is given to the methods of nonconventional machining, such as laser machining, water jet cutting, electrical discharge machining, and ultrasonic assisted machining. Also discussed are safety precautions which must be taken during machining of fiber-containing composites.

  4. Machining fiber-reinforced composites

    Science.gov (United States)

    Komanduri, Ranga

    1993-04-01

    Compared to high tool wear and high costs of tooling of fiber-reinforced composites (FRCs), noncontact material-removal processes offer attractive alternative. Noncontact machining methods can also minimize dust, noise, and extensive plastic deformation and consequent heat generation associated with conventional machining of FRCs, espacially those with an epoxy matrix. The paper describes the principles involved in and the details of machining of FRCs by laser machining, water jet-cutting and abrasive water jet-cutting, and electrical discharge machining of composites, as well as the limitations of each method.

  5. Lignocellulosic fiber reinforced rubber composites

    CSIR Research Space (South Africa)

    Jacob John, Maya

    2009-04-01

    Full Text Available stream_source_info John_d1_2009.pdf.txt stream_content_type text/plain stream_size 43167 Content-Encoding UTF-8 stream_name John_d1_2009.pdf.txt Content-Type text/plain; charset=UTF-8 -252- CHAPTER 10: LIGNOCELLULOSIC... FIBER REINFORCED RUBBER COMPOSITES Maya JACOB JOHN1 Rajesh D. ANANDJIWALA2 (1)CSIR Materials Science and Manufacturing, Fibres and Textiles Competence Area, P.O. Box 1124, Port Elizabeth 6000, South Africa, E-mail: mjohn@csir.co.za (2) Department...

  6. A novel basalt fiber-reinforced polylactic acid composite for hard tissue repair.

    Science.gov (United States)

    Chen, Xi; Li, Yan; Gu, Ning

    2010-08-01

    A basalt fiber (BF) was, for the first time, introduced into a poly(l-lactic acid) (PLLA) matrix as innovative reinforcement to fabricate composite materials for hard tissue repair. Firstly, BF/PLLA composites and pure PLLA were produced by the methods of solution blending and freeze drying. The results showed that basalt fibers can be uniformly dispersed in the PLLA matrix and significantly improve the mechanical properties and hydrophilicity of the PLLA matrix. The presence of basalt fibers may retard the polymer degradation rate and neutralize the acid degradation from PLLA. Osteoblasts were cultured in vitro to evaluate the cytocompatibility of the composite. An MTT assay revealed that osteoblasts proliferated well for 7 days and there was little difference found in their viability on both PLLA and BF/PLLA films, which was consistent with the alkaline phosphatase (ALP) activity results. A fluorescent staining observation showed that osteoblasts grew well on the composites. SEM images displayed that osteoblasts tended to grow along the fiber axis. The formation of mineralized nodules was observed on the films by Alizarin red S staining. These results suggest that the presence of basalt fibers does not noticeably affect osteoblastic behavior and the designed composites are osteoblast compatible. It is concluded that basalt fibers, as reinforcing fibers, may have promising applications in hard tissue repair.

  7. Micromechanical failure in fiber-reinforced composites

    DEFF Research Database (Denmark)

    Ashouri Vajari, Danial

    Micromechanical failure mechanisms occurring in unidirectional fiber-reinforced composites are studied by means of the finite element method as well as experimental testing. This study highlights the effect of micro-scale features such as fiber/matrix interfacial debonding, matrix cracking and mi...

  8. Fiber reinforced polymer composites for bridge structures

    Directory of Open Access Journals (Sweden)

    Alexandra CANTORIU

    2013-12-01

    Full Text Available Rapid advances in construction materials technology have led to the emergence of new materials with special properties, aiming at safety, economy and functionality of bridges structures. A class of structural materials which was originally developed many years ago, but recently caught the attention of engineers involved in the construction of bridges is fiber reinforced polymer composites. This paper provides an overview of fiber reinforced polymer composites used in bridge structures including types, properties, applications and future trends. The results of this study have revealed that this class of materials presents outstanding properties such as high specific strength, high fatigue and environmental resistance, lightweight, stiffness, magnetic transparency, highly cost-effective, and quick assembly, but in the same time high initial costs, lack of data on long-term field performance, low fire resistance. Fiber reinforced polymer composites were widely used in construction of different bridge structures such as: deck and tower, I-beams, tendons, cable stands and proved to be materials for future in this field.

  9. Investigation of chloride induced corrosion of bridge pier and life-cycle repair cost analysis using fiber reinforced polymer composites

    Science.gov (United States)

    Dhakal, Dinesh

    Bridges are the long term investment of the highway agencies. To maintain the required service level throughout the life of a bridge, a series of maintenance, repair, and rehabilitation (MRℝ) works can be performed. To investigate the corrosion deterioration and maintenance and repair practices in the bridge pier columns constructed in chloride-laden environment, a questionnaire survey was conducted within the 50 state Departments of Transportation (DOTs). Based on the survey data, two corrosion deterioration phases were identified. They were corrosion crack initiation phase and corrosion propagation phase. The data showed that the mean corrosion crack initiation phase for bridge pier column having cover of 50 mm, 75 mm, and 100 mm was 18.9 years, 20.3 years, and 22.5 years, respectively. The corrosion propagation phase starts after the corrosion crack initiation. The corrosion propagation is defined in a single term, corrosion damage rate, measured as percentage of area damaged due to corrosion cracking, spalling, and delamination. From the survey, the corrosion damage rate was found 2.23% and 2.10% in the bridge pier columns exposed to deicing salt water and exposed to tidal splash/spray, respectively. For this study, two different corrosion damage rates were proposed before and after the repair criteria for minor damage repair as practiced by DOTs. This study also presents the collected data regarding the corrosion effectiveness of using sealers and coatings, cathodic protection, corrosion inhibitors, carbon fiber/epoxy composites, and glass fiber/epoxy composites as maintenance and repair technique. In this study, the cost-effectiveness of wrapping carbon fiber/epoxy composites and glass fiber/epoxy composites in bridge pier columns constructed in a chloride-laden environment was investigated by conducting life-cycle cost analysis. As a repair work, externally bonded two layer of carbon fiber/epoxy and glass fiber/epoxy composites were installed by wet

  10. Effect of hybrid fiber reinforcement on the cracking process in fiber reinforced cementitious composites

    DEFF Research Database (Denmark)

    Pereira, Eduardo B.; Fischer, Gregor; Barros, Joaquim A.O.

    2012-01-01

    The simultaneous use of different types of fibers as reinforcement in cementitious matrix composites is typically motivated by the underlying principle of a multi-scale nature of the cracking processes in fiber reinforced cementitious composites. It has been hypothesized that while undergoing...... tensile deformations in the composite, the fibers with different geometrical and mechanical properties restrain the propagation and further development of cracking at different scales from the micro- to the macro-scale. The optimized design of the fiber reinforcing systems requires the objective...... assessment of the contribution of each type of fiber to the overall tensile response. Possible synergistic effects resulting from particular combinations of fibers need to be clearly identified. In the present study, the evaluation of the response of different fiber reinforced cementitious composite...

  11. Carbon fiber reinforced thermoplastic composites for future automotive applications

    Science.gov (United States)

    Friedrich, K.

    2016-05-01

    After a brief introduction to polymer composite properties and markets, the state of the art activities in the field of manufacturing of advanced composites for automotive applications are elucidated. These include (a) long fiber reinforced thermoplastics (LFT) for secondary automotive components, and (b) continuous carbon fiber reinforced thermosetting composites for car body applications. It is followed by future possibilities of carbon fiber reinforced thermoplastic composites for e.g. (i) crash elements, (ii) racing car seats, and (iii) production and recycling of automotive fenders.

  12. CODIFICATION OF FIBER REINFORCED COMPOSITE PIPING

    Energy Technology Data Exchange (ETDEWEB)

    Rawls, G.

    2012-10-10

    The goal of the overall project is to successfully adapt spoolable FRP currently used in the oil industry for use in hydrogen pipelines. The use of FRP materials for hydrogen service will rely on the demonstrated compatibility of these materials for pipeline service environments and operating conditions. The ability of the polymer piping to withstand degradation while in service, and development of the tools and data required for life management are imperative for successful implementation of these materials for hydrogen pipeline. The information and data provided in this report provides the technical basis for the codification for fiber reinforced piping (FRP) for hydrogen service. The DOE has invested in the evaluation of FRP for the delivery for gaseous hydrogen to support the development of a hydrogen infrastructure. The codification plan calls for detailed investigation of the following areas: System design and applicable codes and standards; Service degradation of FRP; Flaw tolerance and flaw detection; Integrity management plan; Leak detection and operational controls evaluation; Repair evaluation. The FRP codification process started with commercially available products that had extensive use in the oil and gas industry. These products have been evaluated to assure that sufficient structural integrity is available for a gaseous hydrogen environment.

  13. Drastic Improvements in Bonding of Fiber Reinforced Multifunctional Composites Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Achievement of a dramatic increase in the bond strength in the adhesive and composite/adhesive interfaces of existing fiber reinforced composite material joints and...

  14. Drastic Improvements in Bonding of Fiber Reinforced Multifunctional Composites Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Achievement of a dramatic increase in the bond strength in the composite/adhesive interfaces of existing fiber reinforced polymer (FRP) composite material joints and...

  15. Puncture-Healing Thermoplastic Resin Carbon-Fiber-Reinforced Composites

    Science.gov (United States)

    Gordon, Keith L. (Inventor); Siochi, Emilie J. (Inventor); Grimsley, Brian W. (Inventor); Cano, Roberto J. (Inventor); Czabaj, Michael W. (Inventor)

    2015-01-01

    A composite comprising a combination of a self-healing polymer matrix and a carbon fiber reinforcement is described. In one embodiment, the matrix is a polybutadiene graft copolymer matrix, such as polybutadiene graft copolymer comprising poly(butadiene)-graft-poly(methyl acrylate-co-acrylonitrile). A method of fabricating the composite is also described, comprising the steps of manufacturing a pre-impregnated unidirectional carbon fiber preform by wetting a plurality of carbon fibers with a solution, the solution comprising a self-healing polymer and a solvent, and curing the preform. A method of repairing a structure made from the composite of the invention is described. A novel prepreg material used to manufacture the composite of the invention is described.

  16. Modeling of properties of fiber reinforced cement composites

    Directory of Open Access Journals (Sweden)

    Jevtić Dragica

    2008-01-01

    Full Text Available This paper presents the results of authors' laboratory testing of the influence of steel fibers as fiber reinforcement on the change of properties of cement composite mortar and concrete type materials. Mixtures adopted - compositions of mortars had identical amounts of components: cement, sand and silica fume. The second type of mortar contained 60 kg/m3 of fiber reinforcement, as well as the addition of the latest generation of superplasticizer. Physical and mechanical properties of fiber reinforced mortars and etalon mixtures (density, flexural strength, compressive strength were compared. Tests on concrete type cement composites included: density, mechanical strengths and the deformation properties. The tests showed an improvement in the properties of fiber reinforced composites.

  17. Micromechanical modeling of strength and damage of fiber reinforced composites

    Energy Technology Data Exchange (ETDEWEB)

    Mishnaevsky, L. Jr.; Broendsted, P.

    2007-03-15

    The report for the first year of the EU UpWind project includes three parts: overview of concepts and methods of modelling of mechanical behavior, deformation and damage of unidirectional fiber reinforced composites, development of computational tools for the automatic generation of 3D micromechanical models of fiber reinforced composites, and micromechanical modelling of damage in FRC, and phenomenological analysis of the effect of frequency of cyclic loading on the lifetime and damage evolution in materials. (au)

  18. Fiber-reinforced composites in fixed partial dentures

    Directory of Open Access Journals (Sweden)

    Vallittu P

    2006-08-01

    Full Text Available Fiber-reinforced composite resin (FRC prostheses offer the advantages of good esthetics, minimal invasive treatment, and an ability to bond to the abutment teeth, thereby compensating for less-than-optimal abutment tooth retention and resistance form. These prostheses are composed of two types of composite materials: fiber composites to build the framework and hybrid or microfill particulate composites to create the external veneer surface. This review concentrates on the use of fiber reinforcement in the fabrication of laboratory or chairside-made composite-fixed partial dentures of conventional preparation. Other applications of FRC in dentistry are briefly mentioned. The possibilities fiber reinforcement technology offers must be emphasized to the dental community. Rather than limiting discussion to whether FRC prostheses will replace metal-ceramic or full-ceramic prostheses, attention should be focused on the additional treatment options brought by the use of fibers. However, more clinical experience is needed.

  19. High Performance Fiber Reinforced Cement Composites 6 HPFRCC 6

    CERN Document Server

    Reinhardt, Hans; Naaman, A

    2012-01-01

    High Performance Fiber Reinforced Cement Composites (HPFRCC) represent a class of cement composites whose stress-strain response in tension undergoes strain hardening behaviour accompanied by multiple cracking, leading to a high strain prior to failure. The primary objective of this International Workshop was to provide a compendium of up-to-date information on the most recent developments and research advances in the field of High Performance Fiber Reinforced Cement Composites. Approximately 65 contributions from leading world experts are assembled in these proceedings and provide an authoritative perspective on the subject. Special topics include fresh and hardening state properties; self-compacting mixtures; mechanical behavior under compressive, tensile, and shear loading; structural applications; impact, earthquake and fire resistance; durability issues; ultra-high performance fiber reinforced concrete; and textile reinforced concrete. Target readers: graduate students, researchers, fiber producers, desi...

  20. Hybrid fiber reinforcement and crack formation in Cementitious Composite Materials

    DEFF Research Database (Denmark)

    Pereira, E.B.; Fischer, Gregor; Barros, J.A.O.

    2011-01-01

    reinforcement systems. The research described in this paper shows that the multi-scale conception of cracking and the use of hybrid fiber reinforcements do not necessarily result in an improved tensile behavior of the composite. Particular material design requirements may nevertheless justify the use of hybrid......- to the macroscale. In this study, the performance of different fiber reinforced cementitious composites is assessed in terms of their tensile stress-crack opening behavior. The results obtained from this investigation allow a direct quantitative comparison of the behavior obtained from the different fiber...

  1. Micromechanisms of damage in unidirectional fiber reinforced composites

    DEFF Research Database (Denmark)

    Mishnaevsky, Leon; Brøndsted, Povl

    2009-01-01

    Numerical micromechanical investigations of the mechanical behavior and damage evolution of glass fiber reinforced composites are presented. A program code for the automatic generation of 3D micromechanical unit cell models of composites with damageable elements is developed, and used in the nume...

  2. An Assessment of Self-Healing Fiber Reinforced Composites

    Science.gov (United States)

    Smith, Joseph G., Jr.

    2012-01-01

    Several reviews and books have been written concerning self-healing polymers over the last few years. These have focused primarily on the types of self-healing materials being studied, with minor emphasis given to composite properties. The purpose of this review is to assess the self-healing ability of these materials when utilized in fiber reinforced composites

  3. Fiber-Reinforced-Foam (FRF) Core Composite Sandwich Panel Concept for Advanced Composites Technologi

    Science.gov (United States)

    2010-01-01

    Fiber-Reinforced-Foam (FRF) Core Composite Sandwich Panel Concept for Advanced Composites Technologies Project - Preliminary Manufacturing Demonstration Articles for Ares V Payload Shroud Barrel Acreage Structure

  4. Fiber-reinforced bioactive and bioabsorbable hybrid composites

    Energy Technology Data Exchange (ETDEWEB)

    Huttunen, Mikko; Godinho, Pedro; Kellomaeki, Minna [Tampere University of Technology, Institute of Biomaterials, Hermiankatu 12, PO Box 589, FIN-33101 Tampere (Finland); Toermaelae, Pertti [Bioretec Ltd, Hermiankatu 22, PO Box 135, FI-33721 Tampere (Finland)], E-mail: mikko.huttunen@tut.fi

    2008-09-01

    Bioabsorbable polymeric bone fracture fixation devices have been developed and used clinically in recent decades to replace metallic implants. An advantage of bioabsorbable polymeric devices is that these materials degrade in the body and the degradation products exit via metabolic routes. Additionally, the strength properties of the bioabsorbable polymeric devices decrease as the device degrades, which promotes bone regeneration (according to Wolff's law) as the remodeling bone tissue is progressively loaded. The most extensively studied bioabsorbable polymers are poly-{alpha}-hydroxy acids. The major limitation of the first generation of bioabsorbable materials and devices was their relatively low mechanical properties and brittle behavior. Therefore, several reinforcing techniques have been used to improve the mechanical properties. These include polymer chain orientation techniques and the use of fiber reinforcements. The latest innovation for bioactive and fiber-reinforced bioabsorbable composites is to use both bioactive and bioresorbable ceramic and bioabsorbable polymeric fiber reinforcement in the same composite structure. This solution of using bioactive and fiber-reinforced bioabsorbable hybrid composites is examined in this study.

  5. Fracture morphology of carbon fiber reinforced plastic composite laminates

    OpenAIRE

    Vinod Srinivasa; Vinay Shivakumar; Vinay Nayaka; Sunil Jagadeeshaiaih; Murali Seethram; Raghavendra Shenoy; Abdelhakim Nafidi

    2010-01-01

    Carbon fiber reinforced plastic (CFRP) composites have been extensively used in fabrication of primary structures for aerospace, automobile and other engineering applications. With continuous and widespread use of these composites in several advanced technology, the frequency of failures is likely to increase. Therefore, to establish the reasons for failures, the fracture modes should be understood thoroughly and unambiguously. In this paper, CFRP composite have been tested in tension, compre...

  6. Chairside fabricated fiber-reinforced composite fixed partial denture

    OpenAIRE

    Garoushi, Sufyan; Vallittu, Pekka K

    2007-01-01

    The advances in the materials and techniques for adhesive dentistry have allowed the development of non-invasive or minimally invasive approaches for replacing a missing tooth in those clinical situations when conservation of adjacent teeth is needed. Good mechanical and cosmetic/aesthetic properties of fiber-reinforced composite (FRC), with good bonding properties with composite resin cement and veneering composite are needed in FRC devices. Some recent studies have shown that adhesives of c...

  7. Studies on natural fiber reinforced polymer matrix composites

    Science.gov (United States)

    Patel, R. H.; Kapatel, P. M.; Machchhar, A. D.; Kapatel, Y. A.

    2016-05-01

    Natural fiber reinforced composites show increasing importance in day to days applications because of their low cost, lightweight, easy availability, non-toxicity, biodegradability and environment friendly nature. But these fibers are hydrophilic in nature. Thus they have very low reactivity and poor compatibility with polymers. To overcome these limitations chemical modifications of the fibers have been carried out. Therefore, in the present work jute fibers have chemically modified by treating with sodium hydroxide (NaOH) solutions. These treated jute fibers have been used to fabricate jute fiber reinforced epoxy composites. Mechanical properties like tensile strength, flexural strength and impact strength have been found out. Alkali treated composites show better properties compare to untreated composites.

  8. Hybrid fiber reinforcement and crack formation in Cementitious Composite Materials

    DEFF Research Database (Denmark)

    Pereira, E.B.; Fischer, Gregor; Barros, J.A.O.

    2011-01-01

    reinforcement systems. The research described in this paper shows that the multi-scale conception of cracking and the use of hybrid fiber reinforcements do not necessarily result in an improved tensile behavior of the composite. Particular material design requirements may nevertheless justify the use of hybrid......The use of different types of fibers simultaneously for reinforcing cementitious matrices is motivated by the concept of a multi-scale nature of the crack propagation process. Fibers with different geometrical and mechanical properties are used to bridge cracks of different sizes from the micro......- to the macroscale. In this study, the performance of different fiber reinforced cementitious composites is assessed in terms of their tensile stress-crack opening behavior. The results obtained from this investigation allow a direct quantitative comparison of the behavior obtained from the different fiber...

  9. Glass fiber reinforcement in repaired acrylic resin removable dentures: preliminary results of a clinical study.

    Science.gov (United States)

    Vallittu, P K

    1997-01-01

    The clinical usefulness of continuous E-glass partial fiber reinforcement of acrylic resin removable dentures was evaluated an average 13 months after the insertion of the fibers. Twelve removable complete dentures and ten removable partial dentures with a history of recurrent fracture were selected for this study. The partial fiber reinforcement was incorporated into the denture at the time of repair. One complete denture and one removable partial denture fractured in the region of reinforcement during the examination period. These fractures were most likely caused by faulty placement of the fiber reinforcement in the denture in the dental laboratory. In six dentures, new fractures occurred in regions without partial fiber reinforcement. The results revealed the importance of both the correct positioning of the partial fiber reinforcement in the denture and the use of accurate laboratory techniques.

  10. Fabrication of fiber-reinforced composites by chemical vapor infiltration

    Energy Technology Data Exchange (ETDEWEB)

    Besmann, T.M.; Stinton, D.P. [Oak Ridge National Lab., TN (United States); Matlin, W.M.; Liaw, P.K. [Univ. of Tennessee, Knoxville, TN (United States)

    1996-08-01

    Processing equipment for the infiltration of fiber-reinforced composite tubes is being designed that incorporates improvements over the equipment used to infiltrate disks. A computer-controlled machine-man interface is being developed to allow for total control of all processing variables. Additionally, several improvements are being made to the furnace that will reduce the complexity and cost of the process. These improvements include the incorporation of free standing preforms, cast mandrels, and simpler graphite heating elements.

  11. Fabrication of fiber-reinforced composites by chemical vapor infiltration

    Energy Technology Data Exchange (ETDEWEB)

    Besmann, T.M.; Matlin, W.M.; Stinton, D.P.; Liaw, P.K.

    1996-06-01

    Processing equipment for the infiltration of fiber-reinforced composite tubes is being designed that incorporates improvements over the equipment used to infiltrate disks. A computer-controlled machine-man interface is being developed to allow for total control of all processing variables. Additionally, several improvements are being made to the furnace that will reduce the complexity and cost of the process. These improvements include the incorporation of free standing preforms, cast mandrels, and simpler graphite heating elements.

  12. Self-healing in single and multiple fiber(s) reinforced polymer composites

    OpenAIRE

    2010-01-01

    You Polymer composites have been attractive medium to introduce the autonomic healing concept into modern day engineering materials. To date, there has been significant research in self-healing polymeric materials including several studies specifically in fiber reinforced polymers. Even though several methods have been suggested in autonomic healing materials, the concept of repair by bleeding of enclosed functional agents has garnered wide attention by the scientific community. A self-...

  13. Tungsten fiber reinforced copper matrix composites: A review

    Science.gov (United States)

    Mcdanels, David L.

    1989-01-01

    Tungsten fiber reinforced copper matrix (W/Cu) composites have served as an ideal model system with which to analyze the properties of metal matrix composites. A series of research programs were conducted to investigate the stress-strain behavior of W/Cu composites; the effect of fiber content on the strength, modulus, and conductivity of W/Cu composites; and the effect of alloying elements on the behavior of tungsten wire and of W/Cu composites. Later programs investigated the stress-rupture, creep, and impact behavior of these composites at elevated temperatures. Analysis of the results of these programs as allows prediction of the effects of fiber properties, matrix properties, and fiber content on the properties of W/Cu composites. These analyses form the basis for the rule-of-mixtures prediction of composite properties which was universally adopted as the criteria for measuring composite efficiency. In addition, the analyses allows extrapolation of potential properties of other metal matrix composites and are used to select candidate fibers and matrices for development of tungsten fiber reinforced superalloy composite materials for high temperature aircraft and rocket engine turbine applications. The W/Cu composite efforts are summarized, some of the results obtained are described, and an update is provided on more recent work using W/Cu composites as high strength, high thermal conductivity composite materials for high heat flux, elevated temperature applications.

  14. Thermoforming continuous fiber-reinforced thermoplastic composites

    Energy Technology Data Exchange (ETDEWEB)

    Wu, Xiang.

    1990-01-01

    In this research the forming process was first decomposed into basic deformation elements with simple geometries, and models were then developed for these elements. A series-parallel model was developed for predicting the upper and lower bounds of composite shear modulus at forming temperature based on the fiber content, fiber distribution, and matrix shear modulus. A shear-flexure model was proposed to describe the initial load-deflection behavior of thermoplastic composites in bending. A ply buckling model was developed which included the contributions from both a surface tension term and a ply buckling term.

  15. Continuous fiber-reinforced titanium aluminide composites

    Science.gov (United States)

    Mackay, R. A.; Brindley, P. K.; Froes, F. H.

    1991-01-01

    An account is given of the fabrication techniques, microstructural characteristics, and mechanical behavior of a lightweight, high service temperature SiC-reinforced alpha-2 Ti-14Al-21Nb intermetallic-matrix composite. Fabrication techniques under investigation to improve the low-temperature ductility and environmental resistance of this material system, while reducing manufacturing costs to competitive levels, encompass powder-cloth processing, foil-fiber-foil processing, and thermal-spray processing. Attention is given to composite microstructure problems associated with fiber distribution and fiber-matrix interfaces, as well as with mismatches of thermal-expansion coefficient; major improvements are noted to be required in tensile properties, thermal cycling effects, mechanical damage, creep, and environmental effects.

  16. Homogenization of long fiber reinforced composites including fiber bending effects

    DEFF Research Database (Denmark)

    Poulios, Konstantinos; Niordson, Christian Frithiof

    2016-01-01

    This paper presents a homogenization method, which accounts for intrinsic size effects related to the fiber diameter in long fiber reinforced composite materials with two independent constitutive models for the matrix and fiber materials. A new choice of internal kinematic variables allows...... of the reinforcing fibers is captured by higher order strain terms, resulting in an accurate representation of the micro-mechanical behavior of the composite. Numerical examples show that the accuracy of the proposed model is very close to a non-homogenized finite-element model with an explicit discretization...

  17. Fracture of fiber-reinforced composites analyzed via acoustic emission.

    Science.gov (United States)

    Ereifej, Nadia S; Oweis, Yara G; Altarawneh, Sandra K

    2015-01-01

    This study investigated the fracture resistance of composite resins using a three-point bending test and acoustic emission (AE) analysis. Three groups of specimens (n=15) were prepared: non-reinforced BelleGlass HP composite (NRC), unidirectional (UFRC) and multidirectional (MFRC) fiber-reinforced groups which respectively incorporated unidirectional Stick and multidirectional StickNet fibers. Specimens were loaded to failure in a universal testing machine while an AE system was used to detect audible signals. Initial fracture strengths and AE amplitudes were significantly lower than those at final fracture in all groups (pcomposite resin materials and the monitoring of acoustic signals revealed significant information regarding the fracture process.

  18. Banana fiber-reinforced biodegradable soy protein composites

    Institute of Scientific and Technical Information of China (English)

    Rakesh Kumar; Veena Choudhary; Saroj Mishra; Ik Varma

    2008-01-01

    Banana fiber,a waste product of banana cultivation,has been used to prepare banana fiber reinforced soy protein composites. Alkali modified banana fibers were characterized in terms of density,denier and crystallinity index. Fourier transformed infrared spectroscopy (FTIR),scanning electron microscopy (SEM) and thermogravimetric analysis (TGA) were also performed on the fibers. Soy protein composites were prepared by incorporating different volume fractions of alkali,treated and untreated fibers into soy protein isolate (SPI) with different amounts of glycerol (25%,50%) as plasticizer.Composites thus prepared were characterized in terms of mechanical properties,SEM and water resistance.The results indicate that at 0.3 volume fraction,tensile strength and modulus of alkali treated fiber reinforced soy protein composites increased to 82% and 963%,respectively,compared to soy protein film without fibers.Water resistance of the composites increased significantly with the addition of glutaraldehyde which acts as crosslinking agent. Biodegradability of the composites has also been tested in the contaminated environment and the composites were found to be 100% biodegradable.

  19. Fatigue fracture of fiber reinforced polymer honeycomb composite sandwich structures for gas turbine engines

    Science.gov (United States)

    Nikhamkin, Mikhail; Sazhenkov, Nikolai; Samodurov, Danil

    2017-05-01

    Fiber reinforced polymer honeycomb composite sandwich structures are commonly used in different industries. In particular, they are used in the manufacture of gas turbine engines. However, fiber reinforced polymer honeycomb composite sandwich structures often have a manufacturing flaw. In theory, such flaws due to their rapid propagation reduce the durability of fiber reinforced polymer honeycomb composite sandwich structures. In this paper, bending fatigue tests of fiber reinforced polymer honeycomb composite sandwich structures with manufacturing flaws were conducted. Comparative analysis of fatigue fracture of fiber reinforced polymer honeycomb composite sandwich specimens was conducted before and after their bending fatigue tests. The analysis was based on the internal damage X-ray observation of fiber reinforced polymer honeycomb composite sandwich specimens.

  20. The assessment of metal fiber reinforced polymeric composites

    Science.gov (United States)

    Chung, Wenchiang R.

    1990-01-01

    Because of their low cost, excellent electrical conductivity, high specific strength (strength/density), and high specific modulus (modulus/density) short metal fiber reinforced composites have enjoyed a widespread use in many critical applications such as automotive industry, aircraft manufacturing, national defense, and space technology. However, little data has been found in the study of short metal fibrous composites. Optimum fiber concentration in a resin matrix and fiber aspect ratio (length-to-diameter ratio) are often not available to a user. Stress concentration at short fiber ends is the other concern when the composite is applied to a load-bearing application. Fracture in such composites where the damage will be initiated or accumulated is usually difficult to be determined. An experimental investigation is therefore carefully designed and undertaken to systematically evaluate the mechanical properties as well as electrical properties. Inconel 601 (nickel based) metal fiber with a diameter of eight microns is used to reinforce commercially available thermoset polyester resin. Mechanical testing such as tensile, impact, and flexure tests along with electrical conductivity measurements is conducted to study the feasibility of using such composites. The advantages and limitations of applying chopped metal fiber reinforced polymeric composites are also discussed.

  1. Natural Kenaf Fiber Reinforced Composites as Engineered Structural Materials

    Science.gov (United States)

    Dittenber, David B.

    The objective of this work was to provide a comprehensive evaluation of natural fiber reinforced polymer (NFRP)'s ability to act as a structural material. As a chemical treatment, aligned kenaf fibers were treated with sodium hydroxide (alkalization) in different concentrations and durations and then manufactured into kenaf fiber / vinyl ester composite plates. Single fiber tensile properties and composite flexural properties, both in dry and saturated environments, were assessed. Based on ASTM standard testing, a comparison of flexural, tensile, compressive, and shear mechanical properties was also made between an untreated kenaf fiber reinforced composite, a chemically treated kenaf fiber reinforced composite, a glass fiber reinforced composite, and oriented strand board (OSB). The mechanical properties were evaluated for dry samples, samples immersed in water for 50 hours, and samples immersed in water until saturation (~2700 hours). Since NFRPs are more vulnerable to environmental effects than synthetic fiber composites, a series of weathering and environmental tests were conducted on the kenaf fiber composites. The environmental conditions studied include real-time outdoor weathering, elevated temperatures, immersion in different pH solutions, and UV exposure. In all of these tests, degradation was found to be more pronounced in the NFRPs than in the glass FRPs; however, in nearly every case the degradation was less than 50% of the flexural strength or stiffness. Using a method of overlapping and meshing discontinuous fiber ends, large mats of fiber bundles were manufactured into composite facesheets for structural insulated panels (SIPs). The polyisocyanurate foam cores proved to be poorly matched to the strength and stiffness of the NFRP facesheets, leading to premature core shear or delamination failures in both flexure and compressive testing. The NFRPs were found to match well with the theoretical stiffness prediction methods of classical lamination

  2. Self-healing in single and multiple fiber(s reinforced polymer composites

    Directory of Open Access Journals (Sweden)

    Woldesenbet E.

    2010-06-01

    Full Text Available You Polymer composites have been attractive medium to introduce the autonomic healing concept into modern day engineering materials. To date, there has been significant research in self-healing polymeric materials including several studies specifically in fiber reinforced polymers. Even though several methods have been suggested in autonomic healing materials, the concept of repair by bleeding of enclosed functional agents has garnered wide attention by the scientific community. A self-healing fiber reinforced polymer composite has been developed. Tensile tests are carried out on specimens that are fabricated by using the following components: hollow and solid glass fibers, healing agent, catalysts, multi-walled carbon nanotubes, and a polymer resin matrix. The test results have demonstrated that single fiber polymer composites and multiple fiber reinforced polymer matrix composites with healing agents and catalysts have provided 90.7% and 76.55% restoration of the original tensile strength, respectively. Incorporation of functionalized multi-walled carbon nanotubes in the healing medium of the single fiber polymer composite has provided additional efficiency. Healing is found to be localized, allowing multiple healing in the presence of several cracks.

  3. Self-healing in single and multiple fiber(s) reinforced polymer composites

    Science.gov (United States)

    Woldesenbet, E.

    2010-06-01

    You Polymer composites have been attractive medium to introduce the autonomic healing concept into modern day engineering materials. To date, there has been significant research in self-healing polymeric materials including several studies specifically in fiber reinforced polymers. Even though several methods have been suggested in autonomic healing materials, the concept of repair by bleeding of enclosed functional agents has garnered wide attention by the scientific community. A self-healing fiber reinforced polymer composite has been developed. Tensile tests are carried out on specimens that are fabricated by using the following components: hollow and solid glass fibers, healing agent, catalysts, multi-walled carbon nanotubes, and a polymer resin matrix. The test results have demonstrated that single fiber polymer composites and multiple fiber reinforced polymer matrix composites with healing agents and catalysts have provided 90.7% and 76.55% restoration of the original tensile strength, respectively. Incorporation of functionalized multi-walled carbon nanotubes in the healing medium of the single fiber polymer composite has provided additional efficiency. Healing is found to be localized, allowing multiple healing in the presence of several cracks.

  4. Dynamic crack growth in a fiber-reinforced composite plate

    Institute of Scientific and Technical Information of China (English)

    LIU Kaixin; LIU Weifu; Zhang Jinxiang; LI Rong; ZHANG Guohua; FU Bin

    2005-01-01

    This paper reports an experiment on the failure of a precracked plate made of unidirectional glass-epoxy fiber-reinforced composites subjected to three-point bending impact load. In the experiment, the whole process of crack growth was recorded by using high-speed photographic technique, in which a transmitted light path was adopted. Moreover, a new phenomenon of dynamic fracture has been observed. Based on the results, some preliminary studies have been carried out on the rate and path of the crack growth, as well as the failure mode.

  5. Tensile Strength of Natural Fiber Reinforced Polyester Composite

    Science.gov (United States)

    Ismail, Al Emran; Awang, Muhd. Khairudin; Sa'at, Mohd Hisham

    2007-05-01

    Nowadays, increasing awareness of replacing synthetic fiber such as glass fiber has emerged due to environmental problems and pollutions. Automotive manufacturers also seek new material especially biodegradable material to be non-load bearing application parts. This present work discussed on the effect of silane treatment on coir fiber reinforced composites. From the results of tensile tests, fibers treated with silane have attained maximum material stiffness. However, to achieve maximum ultimate tensile strength and strain at failure performances, untreated fibers work very well through fiber bridging and internal friction between fiber and polymeric matrix. Scanning electron microscope (SEM) observations have coincided with these results.

  6. Processing and Performance of Alumina Fiber Reinforced Alumina Composites

    Institute of Scientific and Technical Information of China (English)

    P.Y.Lee; T.Uchijima; T.Yano

    2003-01-01

    Processing of alumina fiber-reinforced alumina matrix composites by hot-pressing was described. The mechanical properties of the composites fabricated by different sintering conditions including temperature and pressure have been investigated. The results indicated that the higher sintering temperature and pressure corresponded to the higher bulk density and higher maximum strength of the composite, whereas the pseudo-ductility of the composite was lower. The preliminary results of the composite with monazite-coated fibers showed that maximum strength could be improved up to 35% compared with the noncoated fiber composite in the same sintering condition. Moreover, the fracture behavior of the composite changed from completely brittle fracture to non-brittle fracture under the suitable sintering conditions. SEM observation of the fracture surface indicated that the coating worked as a protective barrier and avoided sintering of the fibers together even at high temperature and pressure during densification process.

  7. Asymptotic Analysis of Fiber-Reinforced Composites of Hexagonal Structure

    Science.gov (United States)

    Kalamkarov, Alexander L.; Andrianov, Igor V.; Pacheco, Pedro M. C. L.; Savi, Marcelo A.; Starushenko, Galina A.

    2016-08-01

    The fiber-reinforced composite materials with periodic cylindrical inclusions of a circular cross-section arranged in a hexagonal array are analyzed. The governing analytical relations of the thermal conductivity problem for such composites are obtained using the asymptotic homogenization method. The lubrication theory is applied for the asymptotic solution of the unit cell problems in the cases of inclusions of large and close to limit diameters, and for inclusions with high conductivity. The lubrication method is further generalized to the cases of finite values of the physical properties of inclusions, as well as for the cases of medium-sized inclusions. The analytical formulas for the effective coefficient of thermal conductivity of the fiber-reinforced composite materials of a hexagonal structure are derived in the cases of small conductivity of inclusions, as well as in the cases of extremely low conductivity of inclusions. The three-phase composite model (TPhM) is applied for solving the unit cell problems in the cases of the inclusions with small diameters, and the asymptotic analysis of the obtained solutions is performed for inclusions of small sizes. The obtained results are analyzed and illustrated graphically, and the limits of their applicability are evaluated. They are compared with the known numerical and asymptotic data in some particular cases, and very good agreement is demonstrated.

  8. Effect of fiber-reinforced composites on the failure load and failure mode of composite veneers.

    Science.gov (United States)

    Turkaslan, Suha; Tezvergil-Mutluay, Arzu; Bagis, Bora; Vallittu, Pekka k; Lassila, Lippo V J

    2009-09-01

    This study compared the initial and final failure loads and failure modes of indirect resin composite laminate veneers with and without fiber reinforcement. Forty intact lower canines received standard laminate preparations and were randomly assigned into four test groups (n=10). In Group 1, indirect resin composite veneers were repaired with two layers of preimpregnated bidirectional glass fiber weave and a restorative composite; in Group 2, with a layer of preimpregnated unidirectional glass fibers and a restorative composite; and in Group 3, with an experimental semi-IPN matrix composed of multidirectional short glass fibers. Indirect resin composite veneers without any fiber reinforcement were used as control (Group 4). All specimens were thermocycled and tested with a universal testing machine. On the final failure load, there were no statistically significant differences (p>0.05) among the test groups. Within each group, pairwise comparison of initial and final failure loads revealed statistically significant differences (p0.05). On failure mode, unreinforced specimens showed instantaneous failure, whereas reinforced specimens mostly demonstrated elongated failure.

  9. Fiber-reinforced composites materials, manufacturing, and design

    CERN Document Server

    Mallick, P K

    2007-01-01

    The newly expanded and revised edition of Fiber-Reinforced Composites: Materials, Manufacturing, and Design presents the most up-to-date resource available on state-of-the-art composite materials. This book is unique in that it not only offers a current analysis of mechanics and properties, but also examines the latest advances in test methods, applications, manufacturing processes, and design aspects involving composites. This third edition presents thorough coverage of newly developed materials including nanocomposites. It also adds more emphasis on underlying theories, practical methods, and problem-solving skills employed in real-world applications of composite materials. Each chapter contains new examples drawn from diverse applications and additional problems to reinforce the practical relevance of key concepts. New in The Third Edition: Contains new sections on material substitution, cost analysis, nano- and natural fibers, fiber architecture, and carbon-carbon composites Provides a new chapter on poly...

  10. Fracture morphology of carbon fiber reinforced plastic composite laminates

    Directory of Open Access Journals (Sweden)

    Vinod Srinivasa

    2010-09-01

    Full Text Available Carbon fiber reinforced plastic (CFRP composites have been extensively used in fabrication of primary structures for aerospace, automobile and other engineering applications. With continuous and widespread use of these composites in several advanced technology, the frequency of failures is likely to increase. Therefore, to establish the reasons for failures, the fracture modes should be understood thoroughly and unambiguously. In this paper, CFRP composite have been tested in tension, compression and flexural loadings; and microscopic study with the aid of Scanning Electron Microscope (SEM has been performed on failed (fractured composite surfaces to identify the principle features of failure. Efforts have been made in correlating the fracture surface characteristics to the failure mode. The micro-mechanics analysis of failure serves as a useful guide in selecting constituent materials and designing composites from the failure behavior point of view. Also, the local failure initiation results obtained here has been reliably extended to global failure prediction.

  11. Preparation of SiC Fiber Reinforced Nickel Matrix Composite

    Institute of Scientific and Technical Information of China (English)

    Lu Zhang; Nanlin Shi; Jun Gong; Chao Sunt

    2012-01-01

    A method of preparing continuous(Al+Al2O3)-coated SiC fiber reinforced nickel matrix composite was presented,in which the diffusion between SiC fiber and nickel matrix could be prevented.Magnetron sputtering is used to deposit Ni coating on the surface of the(Al+Al2O3)-coated SiC fiber in preparation of the precursor wires.It is shown that the deposited Ni coating combines well with the(Al+Al2O3) coating and has little negative effect on the tensile strength of(Al+Al2O3)-coated SiC fiber.Solid-state diffusion bonding process is employed to prepare the(Al+Al2O3)-coated SiC fiber reinforced nickel matrix with 37% fibers in volume.The solid-state diffusion bonding process is optimized and the optimum parameters are temperature of 870,pressure of 50 MPa and holding time of 2 h.Under this condition,the precursor wires can diffuse well,composite of full density can be formed and the(Al+Al2O3) coating is effective to restrict the reaction between SiC fiber and nickel matrix.

  12. Objective Surface Evaluation of Fiber Reinforced Polymer Composites

    Science.gov (United States)

    Palmer, Stuart; Hall, Wayne

    2013-08-01

    The mechanical properties of advanced composites are essential for their structural performance, but the surface finish on exterior composite panels is of critical importance for customer satisfaction. This paper describes the application of wavelet texture analysis (WTA) to the task of automatically classifying the surface finish properties of two fiber reinforced polymer (FRP) composite construction types (clear resin and gel-coat) into three quality grades. Samples were imaged and wavelet multi-scale decomposition was used to create a visual texture representation of the sample, capturing image features at different scales and orientations. Principal components analysis was used to reduce the dimensionality of the texture feature vector, permitting successful classification of the samples using only the first principal component. This work extends and further validates the feasibility of this approach as the basis for automated non-contact classification of composite surface finish using image analysis.

  13. Chairside fabricated fiber-reinforced composite fixed partial denture

    Directory of Open Access Journals (Sweden)

    Sufyan Garoushi

    2007-01-01

    Full Text Available The advances in the materials and techniques for adhesive dentistry have allowed the development of non-invasive or minimally invasive approaches for replacing a missing tooth in those clinical situations when conservation of adjacent teeth is needed. Good mechanical and cosmetic/aesthetic properties of fiber-reinforced composite (FRC, with good bonding properties with composite resin cement and veneering composite are needed in FRC devices. Some recent studies have shown that adhesives of composite resins and luting cements allow diffusion of the adhesives to the FRC framework of the bridges. By this so-called interdiffusion bonding is formed [1]. FRC bridges can be made in dental laboratories or chairside. This article describes a clinical case of chairside (directly made FRC Bridge, which was used according to the principles of minimal invasive approach. Treatment was performed by Professor Vallittu from the University of Turku, Finland.

  14. Basalt fiber reinforced polymer composites: Processing and properties

    Science.gov (United States)

    Liu, Qiang

    A high efficiency rig was designed and built for in-plane permeability measurement of fabric materials. A new data derivation procedure to acquire the flow fluid pattern in the experiment was developed. The measurement results of the in-plane permeability for basalt twill 31 fabric material showed that a high correlation exists between the two principal permeability values for this fabric at 35% fiber volume fraction. This may be the most important scientific contribution made in this thesis. The results from radial measurements corresponded quite well with those from Unidirectional (UD) measurements, which is a well-established technique. No significant differences in mechanical properties were found between basalt fabric reinforced polymer composites and glass composites reinforced by a fabric of similar weave pattern. Aging results indicate that the interfacial region in basalt composites may be more vulnerable to environmental damage than that in glass composites. However, the basalt/epoxy interface may have been more durable than the glass/epoxy interface in tension-tension fatigue because the basalt composites have significantly longer fatigue life. In this thesis, chapter I reviews the literature on fiber reinforced polymer composites, with concentration on permeability measurement, mechanical properties and durability. Chapter II discusses the design of the new rig for in-plane permeability measurement, the new derivation procedure for monitoring of the fluid flow pattern, and the permeability measurement results. Chapter III compares the mechanical properties and durability between basalt fiber and glass fiber reinforced polymer composites. Lastly, chapter IV gives some suggestions and recommendations for future work.

  15. Homogenization of long fiber reinforced composites including fiber bending effects

    Science.gov (United States)

    Poulios, Konstantinos; Niordson, Christian F.

    2016-09-01

    This paper presents a homogenization method, which accounts for intrinsic size effects related to the fiber diameter in long fiber reinforced composite materials with two independent constitutive models for the matrix and fiber materials. A new choice of internal kinematic variables allows to maintain the kinematics of the two material phases independent from the assumed constitutive models, so that stress-deformation relationships, can be expressed in the framework of hyper-elasticity and hyper-elastoplasticity for the fiber and the matrix materials respectively. The bending stiffness of the reinforcing fibers is captured by higher order strain terms, resulting in an accurate representation of the micro-mechanical behavior of the composite. Numerical examples show that the accuracy of the proposed model is very close to a non-homogenized finite-element model with an explicit discretization of the matrix and the fibers.

  16. Smart Behavior of Carbon Fiber Reinforced Cement-based Composite

    Institute of Scientific and Technical Information of China (English)

    2003-01-01

    The electrical characteristics of cement-based material can be remarkably improved by the addition of short carbon fibers.Carbon fiber reinforced cement composite (CFRC) is an intrinsically smart material that can sense not only the stress andstrain, but also the temperature. In this paper, variations of electrical resistivity with external applied load, and relationof thermoelectric force and temperature were investigated. Test results indicated that the electrical signal is related to theincrease in the material volume resistivity during crack generation or propagation and the decrease in the resistivity duringcrack closure. Moreover, it was found that the fiber addition increased the linearity and reversibility of the Seebeck effect inthe cement-based materials. The change of electrical characteristics reflects large amount of information of inner damage andtemperature differential of composite, which can be used for stress-strain or thermal self-monitoring by embedding it in theconcrete structures.

  17. CO2 Laser Cutting of Glass Fiber Reinforce Polymer Composite

    Science.gov (United States)

    Fatimah, S.; Ishak, M.; Aqida, S. N.

    2012-09-01

    The lamination, matrix properties, fiber orientation, and relative volume fraction of matrix of polymer structure make this polymer hard to process. The cutting of polymer composite using CO2 laser could involve in producing penetration energy in the process. Identification of the dominant factors that significantly affect the cut quality is important. The objective of this experiment is to evaluate the CO2 spot size of beam cutting for Glass Fiber Reinforce Polymer Composite (GFRP). The focal length selected 9.5mm which gave smallest focus spot size according to the cutting requirements. The effect of the focal length on the cut quality was investigated by monitoring the surface profile and focus spot size. The beam parameter has great effect on both the focused spot size and surface quality.

  18. Tensile strength of woven yarn kenaf fiber reinforced polyester composites

    Directory of Open Access Journals (Sweden)

    A.E. Ismail

    2015-12-01

    Full Text Available This paper presents the tensile strength of woven kenaf fiber reinforced polyester composites. The as-received yarn kenaf fiber is weaved and then aligned into specific fiber orientations before it is hardened with polyester resin. The composite plates are shaped according to the standard geometry and uni-axially loaded in order to investigate the tensile responses. Two important parameters are studied such as fiber orientations and number of layers. According to the results, it is shown that fiber orientations greatly affected the ultimate tensile strength but it is not for modulus of elasticity for both types of layers. It is estimated that the reductions of both ultimate tensile strength and Young’s modulus are in the range of 27.7-30.9% and 2.4-3.7% respectively, if the inclined fibers are used with respect to the principal axis.

  19. Modeling oxidation damage of continuous fiber reinforced ceramic matrix composites

    Institute of Scientific and Technical Information of China (English)

    Cheng-Peng Yang; Gui-Qiong Jiao; Bo Wang

    2011-01-01

    For fiber reinforced ceramic matrix composites (CMCs), oxidation of the constituents is a very important damage type for high temperature applications. During the oxidizing process, the pyrolytic carbon interphase gradually recesses from the crack site in the axial direction of the fiber into the interior of the material. Carbon fiber usually presents notch-like or local neck-shrink oxidation phenomenon, causing strength degradation. But, the reason for SiC fiber degradation is the flaw growth mechanism on its surface. A micromechanical model based on the above mechanisms was established to simulate the mechanical properties of CMCs after high temperature oxidation. The statistic and shearlag theory were applied and the calculation expressions for retained tensile modulus and strength were deduced, respectively. Meanwhile, the interphase recession and fiber strength degradation were considered. And then, the model was validated by application to a C/SiC composite.

  20. Neutron stress measurement of W-fiber reinforced Cu composite

    CERN Document Server

    Nishida, M; Ikeuchi, Y; Minakawa, N

    2003-01-01

    Stress measurement methods using neutron and X-ray diffraction were examined by comparing the surface stresses with internal stresses in the continuous tungsten-fiber reinforced copper-matrix composite. Surface stresses were measured by X-ray stress measurement with the sin sup 2 psi method. Furthermore, the sin sup 2 psi method and the most common triaxal measurement method using Hooke's equation were employed for internal stress measurement by neutron diffraction. On the other hand, microstress distributions developed by the difference in the thermal expansion coefficients between these two phases were calculated by FEM. The weighted average strains and stresses were compared with the experimental results. The FEM results agreed with the experimental results qualitatively and confirmed the importance of the triaxial stress analysis in the neutron stress measurement. (Abstract Copyright [2003], Wiley Periodicals, Inc.)

  1. New generation fiber reinforced polymer composites incorporating carbon nanotubes

    Science.gov (United States)

    Soliman, Eslam

    The last five decades observed an increasing use of fiber reinforced polymer (FRP) composites as alternative construction materials for aerospace and infrastructure. The high specific strength of FRP attracted its use as non-corrosive reinforcement. However, FRP materials were characterized with a relatively low ductility and low shear strength compared with steel reinforcement. On the other hand, carbon nanotubes (CNTs) have been introduced in the last decade as a material with minimal defect that is capable of increasing the mechanical properties of polymer matrices. This dissertation reports experimental investigations on the use of multi-walled carbon nanotubes (MWCNTs) to produce a new generation of FRP composites. The experiments showed significant improvements in the flexure properties of the nanocomposite when functionalized MWCNTs were used. In addition, MWCNTs were used to produce FRP composites in order to examine static, dynamic, and creep behavior. The MWCNTs improved the off-axis tension, off-axis flexure, FRP lap shear joint responses. In addition, they reduced the creep of FRP-concrete interface, enhanced the fracture toughness, and altered the impact resistance significantly. In general, the MWCNTs are found to affect the behaviour of the FRP composites when matrix failure dominates the behaviour. The improvement in the mechanical response with the addition of low contents of MWCNTs would benefit many industrial and military applications such as strengthening structures using FRP composites, composite pipelines, aircrafts, and armoured vehicles.

  2. Study on an Improved Phosphate Cement Binder for the Development of Fiber-Reinforced Inorganic Polymer Composites

    Directory of Open Access Journals (Sweden)

    Zhu Ding

    2014-11-01

    Full Text Available Magnesium phosphate cement (MPC has been proven to be a very good repair material for deteriorated concrete structures. It has excellent adhesion performance, leading to high bonding strength with old concrete substrates. This paper presents an experimental study into the properties of MPC binder as the matrix of carbon fiber sheets to form fiber-reinforced inorganic polymer (FRIP composites. The physical and mechanical performance of the fresh mixed and the hardened MPC paste, the bond strength of carbon fiber sheets in the MPC matrix, the tensile strength of the carbon FRIP composites and the microstructure of the MPC matrix and fiber-reinforced MPC composites were investigated. The test results showed that the improved MPC binder is well suited for developing FRIP composites, which can be a promising alternative to externally-bonded fiber-reinforced polymer (FRP composites for the strengthening of concrete structures. Through the present study, an in-depth understanding of the behavior of fiber-reinforced inorganic MPC composites has been achieved.

  3. Research on Flax Fiber Reinforced Polylactide Environmental Friendly Composite

    Institute of Scientific and Technical Information of China (English)

    WANG Chun-hong; WANG Rui; LIU Ming; SHEN Lu; BIAN Dong-cai

    2006-01-01

    Biodegradable polylactide acid (PLA) resin can be combined with flax fibers to produce biodegradable composite materials. In our study, commercial PLA fibers were mixed with flax fibers by a non-woven method so as to make nonwoven pre-forms, which can be generated into flax fiber reinforced PLA environmental friendly composites by heat pressing technology. The tensile, flexural and impact properties are tested in order to evaluate the basic physical properties of the composites, and the influenced factors listed as making technology of the pre-forms, weight ratio of flax fibers and heat pressing technology are discussed and optimized, which can be described as weight ratio of flax fibers and PLA fibers is 50/50, heating temperature, time and pressure are respectively 195℃, 20 min and 12.5 Mpa.Preliminary results show that mechanical properties of the flax/PLA composites are quite promising compared with flax/PP composites in common commercial automotive use.Scanning electron microscope (SEM) is used to analyze the tensile specimen fracture surfaces, which shows voids and gaps occurring between flax fibers and PLA matrix and sign of fiber pull-out, the strength of flax/PLA interface can be further improved.

  4. Fiber reinforced silicon-containing arylacetylene resin composites

    Directory of Open Access Journals (Sweden)

    2007-12-01

    Full Text Available A silicon-containing arylacetylene resin (SAR, a poly(dimethylsilyleneethynylene phenyleneethynylene (PMSEPE, was synthesized. The PMSEPE is a solid resin at ambient temperature with a softening temperature about 60°C and soluble in some solvents like tetrahydrofuran. The melt viscosity of the PMSEPE resin is less than 1 Pa•s. The resin could cure at the temperature of lower than 200°C. Fiber reinforced PMSEPE composites were prepared from prepregs which were made by the impregnation of fibers in PMSEPE resin solution. The composites exhibit good mechanical properties at room temperature and 250°C. The observation on fracture surfaces of the composites reinforced by glass fibers and carbon fibers demonstrates that the adhesion between the fibers and resin is good. The results from an oxyacetylene flame test show that the composites have good ablation performance and XRD analyses indicate that SiC forms in the residues during the ablation of the composites.

  5. Areca Fiber Reinforced Epoxy Composites: Effect of Chemical Treatments on Impact Strength

    Directory of Open Access Journals (Sweden)

    S. Dhanalakshmi

    2015-06-01

    Full Text Available In this research work, impact strength of untreated, alkali treated, potassium permanganate treated, benzoyl chloride treated and acrylic acid treated areca fiber reinforced epoxy composites were studied under 40%, 50%, 60% and 70% fiber loadings. Impact strength increased with increase in fiber loading up to 60% and then showed a decline for all untreated and chemically treated areca fiber reinforced epoxy composites. The acrylic acid treated areca fiber reinforced epoxy composites with 60% fiber loading showed highest impact strength of 28.28 J/mm2 amongst all untreated and chemically treated areca/epoxy composites with same 60% fiber loading.

  6. Development of Glass/Jute Fibers Reinforced Polyester Composite

    Directory of Open Access Journals (Sweden)

    Amit Bindal

    2013-01-01

    Full Text Available Composites play significant role as engineering material and their use has been increasing day by day due to their specific properties such as high strength to weight ratios, high modulus to weight ratio, corrosion resistance, and wear resistance. In present work, an attempt is made to hybridize the material using synthetic (glass as well as natural fibres (chemically treated jute, such that to reduce the overall use of synthetic reinforcement, to reduce the overall cost, and to enhance the mechanical properties. All composite specimens with different weight percentages of fibres were manufactured using hand lay-up process and testing was done by using ASTM standards. Experimental results revealed that hybridization of composite with natural and synthetic fibres shows enhanced tensile strength, flexural strength, and impact strength. The content of natural reinforcement was found to be in the range of 25–33.3% for best results. The effect of treated jute on flexural properties was more than that on tensile properties, which was due to greater stiffness of jute fibers. Chemical treatment of jute fibers lowers the water absorption and results were comparable to glass fiber reinforced polyester composites. The addition of jute also reduced the overall cost by 22.18%.

  7. Microhardness of resin composite materials light-cured through fiber reinforced composite.

    NARCIS (Netherlands)

    Fennis, W.M.M.; Ray, N.J.; Creugers, N.H.J.; Kreulen, C.M.

    2009-01-01

    OBJECTIVES: To compare polymerization efficiency of resin composite basing materials when light-cured through resin composite and fiber reinforced composite (FRC) by testing microhardness. METHODS: Simulated indirect restorations were prepared by application of resin composite (Clearfil AP-X) or FRC

  8. Microhardness of resin composite materials light-cured through fiber reinforced composite.

    NARCIS (Netherlands)

    Fennis, W.M.M.; Ray, N.J.; Creugers, N.H.J.; Kreulen, C.M.

    2009-01-01

    OBJECTIVES: To compare polymerization efficiency of resin composite basing materials when light-cured through resin composite and fiber reinforced composite (FRC) by testing microhardness. METHODS: Simulated indirect restorations were prepared by application of resin composite (Clearfil AP-X) or FRC

  9. Anomaly detection of microstructural defects in continuous fiber reinforced composites

    Science.gov (United States)

    Bricker, Stephen; Simmons, J. P.; Przybyla, Craig; Hardie, Russell

    2015-03-01

    Ceramic matrix composites (CMC) with continuous fiber reinforcements have the potential to enable the next generation of high speed hypersonic vehicles and/or significant improvements in gas turbine engine performance due to their exhibited toughness when subjected to high mechanical loads at extreme temperatures (2200F+). Reinforced fiber composites (RFC) provide increased fracture toughness, crack growth resistance, and strength, though little is known about how stochastic variation and imperfections in the material effect material properties. In this work, tools are developed for quantifying anomalies within the microstructure at several scales. The detection and characterization of anomalous microstructure is a critical step in linking production techniques to properties, as well as in accurate material simulation and property prediction for the integrated computation materials engineering (ICME) of RFC based components. It is desired to find statistical outliers for any number of material characteristics such as fibers, fiber coatings, and pores. Here, fiber orientation, or `velocity', and `velocity' gradient are developed and examined for anomalous behavior. Categorizing anomalous behavior in the CMC is approached by multivariate Gaussian mixture modeling. A Gaussian mixture is employed to estimate the probability density function (PDF) of the features in question, and anomalies are classified by their likelihood of belonging to the statistical normal behavior for that feature.

  10. STUDY THE CREEP OF TUBULAR SHAPED FIBER REINFORCED COMPOSITES

    Directory of Open Access Journals (Sweden)

    Najat J. Saleh

    2013-05-01

    Full Text Available Inpresent work tubular –shaped fiber reinforced composites were manufactured byusing two types of resins ( Epoxy and unsaturated polyester and separatelyreinforced with glass, carbon and kevlar-49 fibers (filament and woven roving,hybrid reinforcement composites of these fibers were also prepared. The fiberswere wet wound on a mandrel using a purposely designed winding machine,developed by modifying an ordinary lathe, in winding angle of 55° for filament. A creep test was made of either the fulltube or specimens taken from it. Creep was found to increase upon reinforcementin accordance to the rule of mixture and mainly decided by the type of singleor hybridized fibers. The creep behavior, showed that the observed strain tendsto appear much faster at higher temperature as compared with that exhibited atroom temperate. The creep rate also found to be depending on fiber type, matrixtype, and the fiber /matrix bonding. The creep energy calculated fromexperimental observations was found to exhibit highest value for hybridizedreinforcement.

  11. Abrasive waterjet machining of fiber reinforced composites: A review

    Science.gov (United States)

    Kalla, D. K.; Dhanasekaran, P. S.; Zhang, B.; Asmatulu, R.

    2012-04-01

    Machining of fiber reinforced polymer (FRP) composites is a major secondary manufacturing activity in the aircraft and automotive industries. Traditional machining of these composites is difficult due to the high abrasiveness nature of their reinforcing constituents. Almost all the traditional machining processes involve in the dissipation of heat into the workpiece which can be resulted in damage to workpiece and rapid wear of the cutting tool. This serious issue has been overcome by water jetting technologies. Abrasive waterjet machining (AWJM) is a nontraditional method and one of the best options for machining FRPs. This paper presents a review of the ongoing research and development in AWJM of FRPs, with a critical review of the physics of the machining process, surface characterization, modeling and the newer application to the basic research. Variable cutting parameters, limitations and safety aspects of AWJM and the noise related issues due to high flow rate of water jet will be addressed. Further challenges and scope of the future development in AWJM are also presented in detail.

  12. Mechanical behavior of Fiber Reinforced SiC/RBSN Ceramic Matrix Composites: Theory and Experiment

    Science.gov (United States)

    1991-01-01

    AD-A235 926 NASA AVSCOM Technical Memorandum 103688 Technical Report 91-C-004 Mechanical Behavior of Fiber Reinforced SiC/RBSN Ceramic Matrix Composites : Theory... CERAMIC MATRIX COMPOSITES : THEORY AND EXPERIMENT Abhisak Chulya* Department of Civil Engineering Cleveland State University Cleveland, Ohio 44115...tough and sufficiently stable continuous fiber- reinforced ceramic matrix composites (CMC) which can survive in oxidizing environ- ments at temperatures

  13. Matrix cracking of fiber-reinforced ceramic composites in shear

    Science.gov (United States)

    Rajan, Varun P.; Zok, Frank W.

    2014-12-01

    The mechanics of cracking in fiber-reinforced ceramic matrix composites (CMCs) under general loadings remains incomplete. The present paper addresses one outstanding aspect of this problem: the development of matrix cracks in unidirectional plies under shear loading. To this end, we develop a model based on potential energy differences upstream and downstream of a fully bridged steady-state matrix crack. Through a combination of analytical solutions and finite element simulations of the constituent stresses before and after cracking, we identify the dominant stress components that drive crack growth. We show that, when the axial slip lengths are much larger than the fiber diameter and when interfacial slip precedes cracking, the shear stresses in the constituents are largely unaffected by the presence of the crack; the changes that do occur are confined to a 'core' region within a distance of about one fiber diameter from the crack plane. Instead, the driving force for crack growth derives mainly from the axial stresses-tensile in the fibers and compressive in the matrix-that arise upon cracking. These stresses are well-approximated by solutions based on shear-lag analysis. Combining these solutions with the governing equation for crack growth yields an analytical estimate of the critical shear stress for matrix cracking. An analogous approach is used in deriving the critical stresses needed for matrix cracking under arbitrary in-plane loadings. The applicability of these results to cross-ply CMC laminates is briefly discussed.

  14. Electromagnetic Shielding and Absorption Properties of Fiber Reinforced Cementitious Composites

    Institute of Scientific and Technical Information of China (English)

    ZHANG Xiuzhi; SUN Wei

    2012-01-01

    In order to investigate the electromagnetic shielding effectiveness (SE) and absorbing properties of fiber reinforced concrete,steel fiber,carbon fiber and synthetic polyvinyl alcohol (PVA) fiber reinforced concrete were researched.The results show that with the increase of fiber volume fraction,the SE and trend of frequency change of corresponding fiber reinforced concrete are enhanced.When the volume content of steel fiber is 3%,the SE of concrete is above 50 dB and its frequency is above 1.8 GHz.Moreover,in the range of 8-18 GHz,steel fiber,carbon fiber and PVA fiber all can improve the microwave absorption properties of concrete.The concrete with 0.5% carbon fiber can achieve the best absorbing property,the minimum reflectivity is about -7 dB; while steel fiber optimal volume fraction is 2%.The reflectivity curve of PVA fiber reinforced concrete fluctuates with the frequency,and the minimum value of the reflectivity is below -10 dB.The results show that fiber reinforced concrete could be used as EMI(electromagnetic interference) prevention buildings by attenuating and reflecting electromagnetic wave energy.

  15. Development of high performance fiber reinforced cement composites (HPFRCC for application as a transition layer of reinforced beams

    Directory of Open Access Journals (Sweden)

    V. J. Ferrari

    Full Text Available This study presents the development and behavior analysis of high performance fiber reinforced cement composites (HPFRCC. The describedmaterials were specifically developed for application as a transition layer: a repair layer that constitutes the stressed chord of reinforcedconcrete beams strengthened in flexure with carbon fiber reinforced polymers (CFRP. Nineteen different composites were produced by thehybridization process, varying the conventional short steel fiber and steel microfiber (manufactured exclusively for this research contentsto modify the microstructure of the material, thus enhancing the stress transfer process from the cement matrix to the fibers. To analyze theresponse to flexural loading, the composites underwent three point bending tests in notched prism specimens. The response of the materialwas obtained considering strength and tenacity parameters (flexural and fracture. There was evidence of high performance by the composites with a pseudo-hardening behavior.

  16. Fabrication of fiber-reinforced composites by chemical vapor infiltration

    Energy Technology Data Exchange (ETDEWEB)

    Besmann, T.M.; McLaughlin, J.C. [Oak Ridge National Lab., TN (United States). Metals and Ceramics Div.; Probst, K.J.; Anderson, T.J. [Univ. of Florida, Gainesville, FL (United States). Dept. of Chemical Engineering; Starr, T.L. [Georgia Inst. of Tech., Atlanta, GA (United States). Dept. of Materials Science and Engineering

    1997-12-01

    Silicon carbide-based heat exchanger tubes are of interest to energy production and conversion systems due to their excellent high temperature properties. Fiber-reinforced SiC is of particular importance for these applications since it is substantially tougher than monolithic SiC, and therefore more damage and thermal shock tolerant. This paper reviews a program to develop a scaled-up system for the chemical vapor infiltration of tubular shapes of fiber-reinforced SiC. The efforts include producing a unique furnace design, extensive process and system modeling, and experimental efforts to demonstrate tube fabrication.

  17. Modeling and simulation of continuous fiber-reinforced ceramic composites

    Science.gov (United States)

    Bheemreddy, Venkata

    Finite element modeling framework based on cohesive damage modeling, constitutive material behavior using user-material subroutines, and extended finite element method (XFEM), are developed for studying the failure behavior of continuous fiber-reinforced ceramic matrix composites (CFCCs) by the example of a silicon carbide matrix reinforced with silicon carbide fiber (SiC/SiCf) composite. This work deals with developing comprehensive numerical models for three problems: (1) fiber/matrix interface debonding and fiber pull-out, (2) mechanical behavior of a CFCC using a representative volume element (RVE) approach, and (3) microstructure image-based modeling of a CFCC using object oriented finite element analysis (OOF). Load versus displacement behavior during a fiber pull-out event was investigated using a cohesive damage model and an artificial neural network model. Mechanical behavior of a CFCC was investigated using a statistically equivalent RVE. A three-step procedure was developed for generating a randomized fiber distribution. Elastic properties and damage behavior of a CFCC were analyzed using the developed RVE models. Scattering of strength distribution in CFCCs was taken into account using a Weibull probability law. A multi-scale modeling framework was developed for evaluating the fracture behavior of a CFCC as a function of microstructural attributes. A finite element mesh of the microstructure was generated using an OOF tool. XFEM was used to study crack propagation in the microstructure and the fracture behavior was analyzed. The work performed provides a valuable procedure for developing a multi-scale framework for comprehensive damage study of CFCCs.

  18. Failure mode interaction in fiber reinforced laminated composites

    Science.gov (United States)

    Prabhakar, Pavana

    A novel computational modeling framework to predict the compressive strength of fiber reinforced polymer matrix composite (FRPC) laminates has been presented. The model development has been motivated by a set of experimental results on the compression response of two different FRPCs. The model accounts for failure mode interaction between kink-banding and interface fracture (or delamination), which are observed in the experimental results. To reduce the size of the computational model, those interfaces that are most susceptible to delamination are first determined through a free-edge stress analysis. Furthermore, 0-axis layers, which are passive in the failure process are represented through an equivalent homogenized model, but the microstructural features of the on-axis layers (zero plies) are retained in the computational model. The predictions of the model matched well with the experimental observations, and they were found to accurately account for failure mechanism interactions. Therefore, this model has the potential to replace the need to carry out large numbers of tests to obtain the compressive strength allowable for FRPC laminates, the latter allowable being an essential element in the design of lightweight FRPC aerostructures. Furthermore, the thesis presents a new computational model to predict fiber/matrix splitting failure, a failure mode that is frequently observed in in-plane tensile failure of FRPC's. By considering a single lamina, this failure mechanism was seamlessly modeled through the development of a continuum-decohesive nite element (CDFE). The CDFE was motivated by the variational multiscale cohesive method (VMCM) presented earlier by Rudraraju et al. (2010) at the University of Michigan. In the CDFE, the transition from a continuum to a non-continuum is modeled directly (physically) without resorting to enrichment of the shape functions of the element. Thus, the CDFE is a natural merger between cohesive elements and continuum elements. The

  19. Perawatan Satu Kunjungan Restorasi Pasak Fiber Reinforced Composite Pada Gigi Insisivus Atas

    Directory of Open Access Journals (Sweden)

    Ria Ariani

    2013-06-01

    Full Text Available Perawatan saluran akar satu kali kunjungan memberikan keuntungan antara lain memperkecil resiko kontaminasi mikroorganisme dan menghemat waktu perawatan. Pasak fiber reinforced composite memiliki ikatan yang baik dengan dentin menggunakan semen resin dan inti dari resin. Penggunaan pasak bisa mengurangi risiko fraktur. Tujuan penulisan laporan kasus ini adalah untuk mengevaluasi hasil restorasi gigi 11 nekrosis pulpa pasca perawatan saluran akar disertai restorasi dengan pasak fiber reinforced composite. Pasien wanita, 22 tahun datang ke Klinik Konservasi RSGM FKG UGM untuk merawat gigi depan atas kanan yang berlubang. Berdasarkan pemeriksaan subjektif, objektif dan radiografis diperoleh diagnosis gigi 11 nekrosis pulpa. pasca perawatan saluran akar gigi Gigi direstorasi dengan resin komposit dan pasak fiber reinforced composite. Kesimpula dari hasil evaluasi klinis saat kontrol tidak ada keluhan rasa sakit dan pasien merasa puas. One Visit Treatment of Fiber Reinforced Compositerestoration in Maxillary Right First Incisivus. One visit root canal treatment is advantageous to minimize the risk of microorganism contamination. It saves time and more tolerable for the patients. Fiber reinforced composite post is fabricated, and it has been known to have a good bond with dentinal wall of root space, resin cement and composite resin core. The use of this post could decrease the risk of fracture. The purpose of this paper is to report the results of dental restoration 11 pulp necrosis after root canal treatment with resin composite restorations and post fiber reinforced composite. A 22 year-old female patient who came to Faculty of Dentistry UGM complained about her maxillary right incisor teeth which decayed and needed a treatment. Based on the subjective, objective and radiograph examinations, it was diagnosed that the pulp was necrotic. After one visit root canal treatment and based on clinical evaluation, it is concluded that the right upper

  20. Technical features and criteria in designing fiber-reinforced composite materials: from the aerospace and aeronautical field to biomedical applications.

    Science.gov (United States)

    Gloria, Antonio; Ronca, Dante; Russo, Teresa; D'Amora, Ugo; Chierchia, Marianna; De Santis, Roberto; Nicolais, Luigi; Ambrosio, Luigi

    2011-01-01

    Polymer-based composite materials are ideal for applications where high stiffness-to-weight and strength-to-weight ratios are required. From aerospace and aeronautical field to biomedical applications, fiber-reinforced polymers have replaced metals, thus emerging as an interesting alternative. As widely reported, the mechanical behavior of the composite materials involves investigation on micro- and macro-scale, taking into consideration micromechanics, macromechanics and lamination theory. Clinical situations often require repairing connective tissues and the use of composite materials may be suitable for these applications because of the possibility to design tissue substitutes or implants with the required mechanical properties. Accordingly, this review aims at stressing the importance of fiber-reinforced composite materials to make advanced and biomimetic prostheses with tailored mechanical properties, starting from the basic principle design, technologies, and a brief overview of composites applications in several fields. Fiber-reinforced composite materials for artificial tendons, ligaments, and intervertebral discs, as well as for hip stems and mandible models will be reviewed, highlighting the possibility to mimic the mechanical properties of the soft and hard tissues that they replace.

  1. Reusing recycled fibers in high-value fiber-reinforced polymer composites: Improving bending strength by surface cleaning

    OpenAIRE

    Shi, Jian; Bao, Limin; Kobayashi, Ryouhei; Kato, Jun; Kemmochi, Kiyoshi

    2012-01-01

    Glass fiber-reinforced polymer (GFRP) composites and carbon fiber-reinforced polymer (CFRP) composites were recycled using superheated steam. Recycled glass fibers (R-GFs) and recycled carbon fibers (R-CFs) were surface treated for reuse as fiber-reinforced polymer (FRP) composites. Treated R-GFs (TR-GFs) and treated R-CFs (TR-CFs) were characterized by scanning electron microscopy (SEM) and remanufactured by vacuum-assisted resin transfer molding (VARTM). Most residual resin impurities were ...

  2. Reusing recycled fibers in high-value fiber-reinforced polymer composites: Improving bending strength by surface cleaning

    OpenAIRE

    Shi, Jian; Bao, Limin; Kobayashi, Ryouhei; Kato, Jun; Kemmochi, Kiyoshi

    2012-01-01

    Glass fiber-reinforced polymer (GFRP) composites and carbon fiber-reinforced polymer (CFRP) composites were recycled using superheated steam. Recycled glass fibers (R-GFs) and recycled carbon fibers (R-CFs) were surface treated for reuse as fiber-reinforced polymer (FRP) composites. Treated R-GFs (TR-GFs) and treated R-CFs (TR-CFs) were characterized by scanning electron microscopy (SEM) and remanufactured by vacuum-assisted resin transfer molding (VARTM). Most residual resin impurities were ...

  3. Effect of Sisal Fiber Surface Treatment on Properties of Sisal Fiber Reinforced Polylactide Composites

    Directory of Open Access Journals (Sweden)

    Zhaoqian Li

    2011-01-01

    Full Text Available Mechanical properties of composites are strongly influenced by the quality of the fiber/matrix interface. The objective of this study was to evaluate the mechanical properties of polylactide (PLA composites as a function of modification of sisal fiber with two different macromolecular coupling agents. Sisal fiber reinforced polylactide composites were prepared by injection molding, and the properties of composites were studied by static/dynamic mechanical analysis (DMA. The results from mechanical testing revealed that surface-treated sisal fiber reinforced composite offered superior mechanical properties compared to untreated fiber reinforced polylactide composite, which indicated that better adhesion between sisal fiber and PLA matrix was achieved. Scanning electron microscopy (SEM investigations also showed that surface modifications improved the adhesion of the sisal fiber/polylactide matrix.

  4. Performance of carbon fiber reinforced rubber composite armour against shaped charge jet penetration

    Directory of Open Access Journals (Sweden)

    Yue Lian-yong

    2016-01-01

    Full Text Available Natural rubber is reinforced with carbon fiber; the protective performances of the carbonfiber reinforced rubber composite armour to shaped charge jet have been studied based on the depth of penetration experiments. The craters on the witness blocks, the nature rubber based composite plates’ deformation and the Scanning Electron Microscopy for the hybrid fiber reinforced rubber plate also is analyzed. The results showed that the composite armour can affect the stability of the jet and made part of the jet fracture. The carbon fiber reinforced rubber composite armour has good defence ablity especially when the nature rubber plate hybrid 15% volume percentage carbonfiber and the obliquity angle is 68°. The hybrid fiber reinforced rubber composite armour can be used as a new kind of light protective armour.

  5. A study on the crushing behavior of basalt fiber reinforced composite structures

    Science.gov (United States)

    Pandian, A.; Veerasimman, A. P.; Vairavan, M.; Francisco, C.; Sultan, M. T. H.

    2016-10-01

    The crushing behavior and energy absorption capacity of basalt fiber reinforced hollow square structure composites are studied under axial compression. Using the hand layup technique, basalt fiber reinforced composites were fabricated using general purpose (GP) polyester resin with the help of wooden square shaped mould of varying height (100 mm, 150 mm and 200 mm). For comparison, similar specimens of glass fiber reinforced polymer composites were also fabricated and tested. Axial compression load is applied over the top end of the specimen with cross head speed as 2 mm/min using Universal Testing Machine (UTM). From the experimental results, the load-deformation characteristics of both glass fiber and basalt fiber composites were investigated. Crashworthiness and mode of collapse for the composites were determined from load-deformation curve, and they were then compared to each other in terms of their crushing behaviors.

  6. Investigations of sewn preform characteristics and quality aspects for the manufacturing of fiber reinforced polymer composites

    OpenAIRE

    Ogale, Amol

    2017-01-01

    Sewn net-shape preform based composite manufacturing technology is widely accepted in combination with liquid composite molding technologies for the manufacturing of fiber reinforced polymer composites. The development of threedimensional dry fibrous reinforcement structures containing desired fiber orientation and volume fraction before the resin infusion is based on the predefined preforming processes. Various preform manufacturing aspects influence the overall composite m...

  7. Determination of Water Diffusion Coefficients and Dynamics in Adhesive/ Carbon Fiber Reinforced Epoxy Resin Composite Joints

    Institute of Scientific and Technical Information of China (English)

    WANG Chao; WANG Zhi; WANG Jing; SU Tao

    2007-01-01

    To determinate the water diffusion coefficients and dynamics in adhesive/carbon fiber reinforced epoxy resin composite joints, energy dispersive X-ray spectroscopy analysis(EDX) is used to establish the content change of oxygen in the adhesive in adhesive/carbon fiber reinforced epoxy resin composite joints. As water is made up of oxygen and hydrogen, the water diffusion coefficients and dynamics in adhesive/carbon fiber reinforced epoxy resin composite joints can be obtained from the change in the content of oxygen in the adhesive during humidity aging, via EDX analysis. The authors have calculated the water diffusion coefficients and dynamics in the adhesive/carbon fiber reinforced epoxy resin composite joints with the aid of both energy dispersive X-ray spectroscopy and elemental analysis. The determined results with EDX analysis are almost the same as those determined with elemental analysis and the results also show that the durability of the adhesive/carbon fiber reinforced epoxy resin composite joints subjected to silane coupling agent treatment is better than those subjected to sand paper burnishing treatment and chemical oxidation treatment.

  8. Evaluation of statistical strength of bamboo fiber and mechanical properties of fiber reinforced green composites

    Institute of Scientific and Technical Information of China (English)

    曹勇; 吴义强

    2008-01-01

    Green composites made from bamboo fibers and biodegradable resins were fabricated with press molding.On the basis of the Weibull distribution and the weakest-link theory,the statistical strength and distribution of bamboo fiber were analyzed,and the tensile strength of green composites was also investigated.The result confirms that the tensile statistical strength of fiber fits well with two-parameter Weibull distribution.In addition,the tensile strength of bamboo fiber reinforced composites is about 330 MPa with the fiber volume fraction of 70%.This value is close to or higher than that of other natural fiber reinforced green composites.

  9. Influence of Carbon & Glass Fiber Reinforcements on Flexural Strength of Epoxy Matrix Polymer Hybrid Composites

    Directory of Open Access Journals (Sweden)

    T.D. Jagannatha

    2015-04-01

    Full Text Available Hybrid composite materials are more attracted by the engineers because of their properties like stiffness and high specific strength which leads to the potential application in the area of aerospace, marine and automobile sectors. In the present investigation, the flexural strength and flexural modulus of carbon and glass fibers reinforced epoxy hybrid composites were studied. The vacuum bagging technique was adopted for the fabrication of polymer hybrid composite materials. The hardness, flexural strength and flexural modulus of the hybrid composites were determined as per ASTM standards. The hardness, flexural strength and flexural modulus were improved as the fiber reinforcement contents increased in the epoxy matrix material.

  10. Mechanical behavior and properties of fiber reinforced ceramic matrix composites for high temperature use

    Institute of Scientific and Technical Information of China (English)

    Chongdu Cho; Qiang Pan; Sangkyo Lee

    2007-01-01

    Ceramics can keep their mechanical characteristics up to 2 000℃ or higher.In this paper,A model to predict ultimate strength of continuous fiber-reinforced brittle matrix composites is developed.A statistical theory for the strength of a uni-axially fiber-reinforced brittle matrix composite is presented.Also a semi-empirical frictional heating method for estimating in-situ interfacial shear in fiber-reinforced ceramic matrix composites was improved.Local uneven fiber packing variation as well as uneven micro-damage during fatigue can be expected to have effects on the composites:generation of frictional heating,thermal gradients,and residual stresses around local fiber breaks.This study examined those engineering interests by the finite element method.

  11. Fiber-Reinforced Epoxy Composites and Methods of Making Same Without the Use of Oven or Autoclave

    Science.gov (United States)

    Barnell, Thomas J. (Inventor); Rauscher, Michael D. (Inventor); Stienecker, Rick D. (Inventor); Nickerson, David M. (Inventor); Tong, Tat H. (Inventor)

    2016-01-01

    Method embodiments for producing a fiber-reinforced epoxy composite comprise providing a mold defining a shape for a composite, applying a fiber reinforcement over the mold, covering the mold and fiber reinforcement thereon in a vacuum enclosure, performing a vacuum on the vacuum enclosure to produce a pressure gradient, insulating at least a portion of the vacuum enclosure with thermal insulation, infusing the fiber reinforcement with a reactive mixture of uncured epoxy resin and curing agent under vacuum conditions, wherein the reactive mixture of uncured epoxy resin and curing agent generates exothermic heat, and producing the fiber-reinforced epoxy composite having a glass transition temperature of at least about 100.degree. C. by curing the fiber reinforcement infused with the reactive mixture of uncured epoxy resin and curing agent by utilizing the exothermically generated heat, wherein the curing is conducted inside the thermally insulated vacuum enclosure without utilization of an external heat source or an external radiation source.

  12. Effects of moisture on glass fiber-reinforced polymer composites

    DEFF Research Database (Denmark)

    Alzamora Guzman, Vladimir Joel; Brøndsted, Povl

    2015-01-01

    performance of wind turbine blades over their lifetime. Here, environmental moisture conditions were simulated by immersing glass fiber-reinforced polymer specimens in salt water for a period of up to 8 years. The mechanical properties of specimens were analyzed before and after immersion to evaluate...... the degradation mechanisms. Single-fiber tensile testing was also performed at different moisture conditions. The water-diffusion mechanism was studied to quantify the diffusion coefficients as a function of salt concentration, sample geometry, and fiber direction. Three degradation mechanisms were observed...

  13. Research on the melt impregnation of continuous carbon fiber reinforced nylon 66 composites

    Science.gov (United States)

    Jia, M. Y.; Li, C. X.; Xue, P.; Chen, K.; Chen, T. H.

    2016-07-01

    Impregnation mold of continuous carbon fiber reinforced thermoplastic composites was designed and built in the article. Based on the theory of fluid mechanics and Darcy's law, a model of the melt impregnation was also established. The influences of fiber bundle width and impregnation pins’ diameter on the impregnation degree were studied by numerical simulation. Continuous carbon fiber reinforced nylon 66 composites were prepared. The effects of coated angle and impregnation mold temperature on the mechanical properties of the composites were also described.The agreement between the experimental data and prediction by the model was found to be satisfactory.

  14. Finite-Element Analysis of Jute- and Coir-Fiber-Reinforced Hybrid Composite Multipanel Plates

    Science.gov (United States)

    Nirbhay, M.; Misra, R. K.; Dixit, A.

    2015-09-01

    Natural-fiber-reinforced polymer composite materials are rapidly gaining interest worldwide both in terms of research and industrial applications. The present work includes the characterization and modeling of jute- and coir-fiber-reinforced hybrid composite materials. The mechanical behavior of a two-panel plate and a sixpanel box structure is analyzed under various loading regimes by using the finite-element software ABAQUS®. Exhaustive parametric studies are also performed to obtain a clear insight into the relationships between various parameters and deflections of the panels and stress distributions in them. Deflections of both the structures are compared and found to be in good agreement with published results. To determine the mechanical behavior of natural-fiber-reinforced composite panels, a finite-element analysis is performed.

  15. NDE of Fiber Reinforced Foam Composite Structures for Future Aerospace Vehicles

    Science.gov (United States)

    Walker, james; Roth, Don; Hopkins, Dale

    2010-01-01

    This slide presentation reviews the complexities of non-destructive evaluation (NDE) of fiber reinforced foam composite structures to be used for aerospace vehicles in the future.Various views of fiber reinforced foam materials are shown and described. Conventional methods of NDE for composites are reviewed such as Micro-computed X-Ray Tomography, Thermography, Shearography, and Phased Array Ultrasonics (PAUT). These meth0ods appear to work well on the face sheet and face sheet ot core bond, they do not provide adequate coverage for the webs. There is a need for additional methods that will examine the webs and web to foam core bond.

  16. Finite-Element Analysis of Crack Arrest Properties of Fiber Reinforced Composites Application in Semi-Elliptical Cracked Pipelines

    Science.gov (United States)

    Wang, Linyuan; Song, Shulei; Deng, Hongbo; Zhong, Kai

    2017-07-01

    In nowadays, repair method using fiber reinforced composites as the mainstream pipe repair technology, it can provide security for X100 high-grade steel energy long-distance pipelines in engineering. In this paper, analysis of cracked X100 high-grade steel pipe was conducted, simulation analysis was made on structure of pipes and crack arresters (CAs) to obtain the J-integral value in virtue of ANSYS Workbench finite element software and evaluation on crack arrest effects was done through measured elastic-plastic fracture mechanics parameter J-integral and the crack arrest coefficient K, in a bid to summarize effect laws of composite CAs and size of pipes and cracks for repairing CAs. The results indicate that the K value is correlated with laying angle λ, laying length L2/D1, laying thickness T1/T2of CAs, crack depth c/T1 and crack length a/c, and calculate recommended parameters for repairing fiber reinforced composite CAs in terms of two different crack forms.

  17. Robotic inspection of fiber reinforced composites using phased array UT

    Science.gov (United States)

    Stetson, Jeffrey T.; De Odorico, Walter

    2014-02-01

    Ultrasound is the current NDE method of choice to inspect large fiber reinforced airframe structures. Over the last 15 years Cartesian based scanning machines using conventional ultrasound techniques have been employed by all airframe OEMs and their top tier suppliers to perform these inspections. Technical advances in both computing power and commercially available, multi-axis robots now facilitate a new generation of scanning machines. These machines use multiple end effector tools taking full advantage of phased array ultrasound technologies yielding substantial improvements in inspection quality and productivity. This paper outlines the general architecture for these new robotic scanning systems as well as details the variety of ultrasonic techniques available for use with them including advances such as wide area phased array scanning and sound field adaptation for non-flat, non-parallel surfaces.

  18. Fast Cure Repair Kit for Composites Project

    Data.gov (United States)

    National Aeronautics and Space Administration — NASA has a need for technologies that will enable them to repair damage to composite structures. Fiber-reinforced polymer composite materials are fast gaining ground...

  19. Use of fiber-reinforced composites to improve the durability of bridge elements

    Science.gov (United States)

    Garon, Ronald; Balaguru, P. N.; Cao, Yong; Lee, K. Wayne

    2000-04-01

    Fiber composites made of carbon fibers and organic polymers are being used to strengthen plain, reinforced, and prestressed concrete structures. The composites are becoming more popular as compared to traditional strengthening with steel plates and jackets because they do not corrode and also have a very high strength to weight ratio. Organic polymers have been used as protective coatings for more than thirty years. The impermeable membrane of the polymer seals the concrete surface of the structures preventing the ingress of salts. Their main drawback is their inability to release vapor pressure buildup that causes damage in the concrete and delamination of the bonded fiber reinforced plastic. As a result of this and other weaknesses in the organic polymers, a new generation of breathable coating materials is being developed. These compositions range from epoxy modified portland cement coatings to completely inorganic silicate systems. The durability of five of the most promising compositions was evaluated under freeze-thaw, wet-dry, and scaling conditions. The silicate matrix was also used to bond carbon tows and fabrics to unreinforced concrete members. These beams were tested after exposure to wet-dry and scaling conditions. The results indicate that the inorganic matrix can be effectively used for repairs. The carbon tows can be used to replace the existing corroded reinforcing bars. The possibility of embedding optical fibers with the carbon fibers to monitor the field performance is being studied.

  20. Micromechanical modeling of damage and fracture of unidirectional fiber reinforced composites

    DEFF Research Database (Denmark)

    Mishnaevsky, Leon; Brøndsted, Povl

    2009-01-01

    An overview of methods of the mathematical modeling of deformation, damage and fracture in fiber reinforced composites is presented. The models are classified into five main groups: shear lag-based, analytical models, fiber bundle model and its generalizations, fracture mechanics based and contin...

  1. Flax fiber reinforced PLA composites: studies on types of PLA and different methods of fabrication

    CSIR Research Space (South Africa)

    Kumar, R

    2011-05-01

    Full Text Available hand, injection molded flax fiber reinforced PLA specimens showed higher tensile modulus (TM) (3.0 GPa) than solution cast cum compression molded specimens (1.9 GPa). In addition, the properties of the composites depend on the nature of PLA used...

  2. INTERFACIAL DEBONDING OF COATED-FIBER-REINFORCED COMPOSITES UNDER TENSION-TENSION CYCLIC LOADING

    Institute of Scientific and Technical Information of China (English)

    Shi Zhifei; Zhou Limin

    2000-01-01

    A new degradation function of the friction coefficient is used. Based on the double shear-lag model and Paris formula, the interfacial damage of coated fiber-reinforced composites under tension-tension cyclic loading is studied. The effects of strength and thickness of the coating materials on the debond stress, debond rate as well as debond length are simulated.

  3. In vitro fracture resistance of fiber reinforced cusp-replacing composite restorations.

    NARCIS (Netherlands)

    Fennis, W.M.M.; Tezvergil, A.; Kuijs, R.H.; Lassila, L.V.; Kreulen, C.M.; Creugers, N.H.J.; Vallittu, P.K.

    2005-01-01

    OBJECTIVES: To assess the fracture resistance and failure mode of fiber reinforced composite (FRC) cusp-replacing restorations in premolars. METHODS: Forty-five extracted sound upper premolars were randomly divided into three groups. Identical MOD cavities with simulated buccal cusp fracture and hei

  4. Adhesive Properties of Bonded Orthodontic Retainers to Enamel : Stainless Steel Wire vs Fiber-reinforced Composites

    NARCIS (Netherlands)

    Foek, Dave Lie Sam; Krebs, Eliza; Sandham, John; Ozcan, Mutlu

    2009-01-01

    Purpose: The objectives of this study were to compare the bond strength of a stainless steel orthodontic wire vs various fiber-reinforced composites (FRC) used as orthodontic retainers on enamel, analyze the failure types after debonding, and investigate the influence of different application proced

  5. In vitro fracture resistance of fiber reinforced cusp-replacing composite restorations.

    NARCIS (Netherlands)

    Fennis, W.M.M.; Tezvergil, A.; Kuijs, R.H.; Lassila, L.V.; Kreulen, C.M.; Creugers, N.H.J.; Vallittu, P.K.

    2005-01-01

    OBJECTIVES: To assess the fracture resistance and failure mode of fiber reinforced composite (FRC) cusp-replacing restorations in premolars. METHODS: Forty-five extracted sound upper premolars were randomly divided into three groups. Identical MOD cavities with simulated buccal cusp fracture and hei

  6. Residual stress measurements in an SiC continuous fiber reinforced Ti matrix composite

    NARCIS (Netherlands)

    Willemse, P.F.; Mulder, F.M.; Wei, W.; Rekveldt, M.Th.; Knight, K.S.

    2000-01-01

    During the fabrication of ceramic fiber reinforced metal matrix composites mismatch stresses will be introduced due to differences in thermal expansion coefficients between the matrix and the fibers. Calculations, based on a coaxial cylinder model, [1 and 2] predict that, for a Ti matrix SiC

  7. Micro-mechanical Analysis of Fiber Reinforced Cementitious Composites using Cohesive Crack Modeling

    DEFF Research Database (Denmark)

    Dick-Nielsen, Lars; Stang, Henrik; Poulsen, Peter Noe

    2006-01-01

    This paper discusses the mechanism appearing during fiber debonding in fiber reinforced cementitious composite. The investigation is performed on the micro scale by use of a Finite Element Model. The model is 3 dimensional and the fictitious crack model and a mixed mode stress formulation...

  8. Bioactive Glass Fiber Reinforced Starch-Polycaprolactone Composite for Bone Applications

    Science.gov (United States)

    Jukola, H.; Nikkola, L.; Gomes, M. E.; Chiellini, F.; Tukiainen, M.; Kellomäki, M.; Chiellini, E.; Reis, R. L.; Ashammakhi, N.

    2008-02-01

    For bone regeneration and repair, combinations of different materials are often needed. Biodegradable polymers are often combined with osteoconductive materials, such as bioactive glass (BaG), which can also improve the mechanical properties of the composite. The aim of this study was to develop and characterize BaG fiber-reinforced starch-poly-ɛ-caprolactone (SPCL) composite. Sheets of SPCL (30/70 wt%) were produced using single-screw extrusion. They were then cut and compression molded in layers with BaG fibers to form composite structures of different combinations. Thermal, mechanical, and degradation properties of the composites were studied. The actual amount of BaG in the composites was determined using combustion tests. A strong endothermic peak indicating melting at about 56 °C was observed by differential scanning calorimetry (DSC) analysis. Thermal gravimetry analysis (TGA) showed that thermal decomposition of SPCL started at 325 °C with the decomposition of starch and continued at 400 °C with the degradation of polycaprolactone (PCL). Initial mechanical properties of the reinforced composites were at least 50% better than the properties of the non-reinforced composites. However, the mechanical properties of the composites after two weeks of hydrolysis were comparable to those of the non-reinforced samples. During the six weeks' hydrolysis the mass of the composites had decreased only by about 5%. The amount of glass in the composites remained the same for the six-week period of hydrolysis. In conclusion, it is possible to enhance the initial mechanical properties of SPCL by reinforcing it with BaG fibers. However, the mechanical properties of the composites are only sufficient for use as filler material and they need to be further improved to allow long-lasting bone applications.

  9. Effect of Fiber Layers on the Fracture Resistance of Fiber Reinforced Composite Bridges

    Directory of Open Access Journals (Sweden)

    A Fazel

    2011-08-01

    Full Text Available Introduction: The purpose of this in vitro study was to introduce the fiber reinforced composite bridges and evaluate the most suitable site and position for placement of fibers in order to get maximum strength. Methods: The study included 20 second premolars and 20 second molars selected for fabricating twenty fiber reinforced composite bridges. Twenty specimens were selected for one fiber layer and the remaining teeth for two fiber layers. In the first group, fibers were placed in the inferior third and in the second group, fibers were placed in both the middle and inferior third region. After tooth preparation, the restorations were fabricated, thermocycled and then loaded with universal testing machine in the middle of the pontics with crosshead speed of 1mm/min. Data was analyzed by Kolmogorov-Smirnov test, Independent sample t test and Kaplan-Meier test. Mode of failure was evaluated using stereomicroscope. Results: Mean fracture resistance for the first and second groups was 1416±467N and 1349±397N, respectively. No significant differences were observed between the groups (P>0.05.In the first group, 5 specimens had delamintation and 5 specimens had detachment between fibers and resin composite. In the second group, there were 4 and 6 delaminations and detachments, respectively. There was no fracture within the fiber. Conclusion: In the fiber reinforced fixed partial dentures, fibers reinforce the tensile side of the connectors but placement of additional fibers at other sites does not increase the fracture resistance of the restoration.

  10. Flexural Strength of Carbon Fiber Reinforced Polymer Repaired Cracked Rectangular Hollow Section Steel Beams

    Directory of Open Access Journals (Sweden)

    Tao Chen

    2015-01-01

    Full Text Available The flexural behavior of rectangular hollow section (RHS steel beams with initial crack strengthened externally with carbon fiber reinforced polymer (CFRP plates was studied. Eight specimens were tested under three-point loading to failure. The experimental program included three beams as control specimens and five beams strengthened with CFRP plates with or without prestressing. The load deflection curves were graphed and failure patterns were observed. The yield loads and ultimate loads with or without repairing were compared together with the strain distributions of the CFRP plate. It was concluded that yield loads of cracked beams could be enhanced with repairing. Meanwhile, the ultimate loads were increased to some extent. The effect of repair became significant with the increase of the initial crack depth. The failure patterns of the repaired specimens were similar to those of the control ones. Mechanical clamping at the CFRP plate ends was necessary to avoid premature peeling between the CFRP plate and the steel beam. The stress levels in CFRP plates were relatively low during the tests. The use of prestressing could improve the utilization efficiency of CFRP plates. It could be concluded that the patching repair could be used to restore the load bearing capacity of the deficient steel beams.

  11. Curaua fiber reinforced high-density polyethylene composites: effect of impact modifier and fiber loading

    OpenAIRE

    Jaqueline Albano de Morais; Renan Gadioli; Marco-Aurelio De Paoli

    2016-01-01

    Abstract Short fibers are used in thermoplastic composites to increase their tensile and flexural resistance; however, it often decreases impact resistance. Composites with short vegetal fibers are not an exception to this behavior. The purpose of this work is to produce a vegetal fiber reinforced composite with improved tensile and impact resistance in relation to the polymer matrix. We used poly(ethylene-co-vinyl acetate), EVA, to recover the impact resistance of high density polyethylene, ...

  12. Interlaminar damage of carbon fiber reinforced polymer composite laminate under continuous wave laser irradiation

    Science.gov (United States)

    Liu, Yan-Chi; Wu, Chen-Wu; Huang, Yi-Hui; Song, Hong-Wei; Huang, Chen-Guang

    2017-01-01

    The interlaminar damages were investigated on the carbon fiber reinforced polymer (CFRP) composite laminate under laser irradiation. Firstly, the laminated T700/BA9916 composites were exposed to continuous wave laser irradiation. Then, the interface cracking patterns of such composite laminates were examined by optical microscopy and scanning electron microscopy. Finally, the Finite Element Analysis (FEA) was performed to compute the interface stress of the laminates under laser irradiation. And the effects of the laser parameters on the interlaminar damage were discussed.

  13. Properties of glass/carbon fiber reinforced epoxy hybrid polymer composites

    Science.gov (United States)

    Patel, R. H.; Sevkani, V. R.; Patel, B. R.; Patel, V. B.

    2016-05-01

    Composite Materials are well known for their tailor-made properties. For the fabrication of composites different types of reinforcements are used for different applications. Sometimes for a particular application, one type of reinforcement may not fulfill the requirements. Therefore, more than one type of reinforcements may be used. Thus, the idea of hybrid composites arises. Hybrid composites are made by joining two or more different reinforcements with suitable matrix system. It helps to improve the properties of composite materials. In the present work glass/carbon fiber reinforcement have been used with a matrix triglycidyl ether of tris(m-hydroxy phenyl) phosphate epoxy resin using amine curing agent. Different physical and mechanical properties of the glass, carbon and glass/carbon fiber reinforced polymeric systems have been found out.

  14. Short fiber reinforced thermoplastic blends

    NARCIS (Netherlands)

    Malchev, P.G.

    2008-01-01

    The present thesis investigates the potential of short fiber reinforced thermoplastic blends, a combination of an immiscible polymer blend and a short fiber reinforced composite, to integrate the easy processing solutions available for short fiber reinforced composites with the high mechanical perfo

  15. Short fiber reinforced thermoplastic blends

    NARCIS (Netherlands)

    Malchev, P.G.

    2008-01-01

    The present thesis investigates the potential of short fiber reinforced thermoplastic blends, a combination of an immiscible polymer blend and a short fiber reinforced composite, to integrate the easy processing solutions available for short fiber reinforced composites with the high mechanical perfo

  16. Analysis of the Behaviour of Composite Steel and Steel Fiber Reinforced Concrete Slabs

    Directory of Open Access Journals (Sweden)

    Mindaugas Petkevičius

    2011-04-01

    Full Text Available There was a pending influence of steel fiber on the strength and stiffness of composite steel–concrete slabs under statical short–time load. Steel profiled sheeting and steel fiber reinforced concrete were used for specimens. Four composite slabs were made. Experimental investigations into the behaviour and influence of steel fiber reinforced concrete in composite slabs were conducted. Transverse, longitudinal, shear deformation and deflection of the slab were measured. The results indicated that the use of steel fiber in composite slabs was effective: strength was 20–24 % higher and the meanings of deflections under the action of the bending moment were 0,6MR (where MR is the bending moment at failure of the slabs and were 16–18 % lower for slabs with usual concrete. Article in Lithuanian

  17. Relationship between mechanical properties and bond durability of short fiber-reinforced resin composite with universal adhesive.

    Science.gov (United States)

    Tsujimoto, Akimasa; Barkmeier, Wayne W; Takamizawa, Toshiki; Watanabe, Hidehiko; Johnson, William W; Latta, Mark A; Miyazaki, Masashi

    2016-10-01

    The purpose of this study was to determine the relationship between mechanical properties and bond durability of short fiber-reinforced resin composite with universal adhesive. As controls, micro-hybrid and nano-hybrid resin composites were tested. The universal adhesives used were Scotchbond Universal, Adhese Universal, and G-Premio Bond. The fracture toughness and flexural properties of resin composites, and shear bond strength and shear fatigue strength of universal adhesive with resin composite using both total-etch and self-etch modes were determined. In the results, short fiber-reinforced resin composite showed significantly higher fracture toughness than did micro-hybrid and nano-hybrid resin composites. The flexural strength and modulus of short fiber-reinforced and nano-hybrid resin composites were significantly lower than were those of micro-hybrid resin composites. Regardless of etching mode, the shear bond strength of universal adhesives with short fiber-reinforced resin composite did not show any significant differences from micro-hybrid and nano-hybrid resin composites. The shear fatigue strength of universal adhesives with short fiber-reinforced resin composite and micro-hybrid resin composites were significantly higher than that of nano-hybrid resin composites. The results of this study suggest that the mechanical properties of short fiber-reinforced resin composite improve their bond durability with universal adhesive.

  18. Studying Impact Damage on Carbon-Fiber Reinforced Aircraft Composite Panels with Sonicir

    Science.gov (United States)

    Han, Xiaoyan; Zhao, Xinyue; Zhang, Ding; He, Qi; Song, Yuyang; Lubowicki, Anthony; Newaz, Golam.; Favro, Lawrence D.; Thomas, Robert L.

    2011-06-01

    Composites are becoming more important materials in commercial aircraft structures such as the fuselage and wings with the new B787 Dreamliner from Boeing which has the target to utilize 50% by weight of composite materials. Carbon-fiber reinforced composites are the material of choice in aircraft structures. This is due to their light weight and high strength (high strength-to-weight ratio), high specific stiffness, tailorability of properties, design flexibility etc. Especially, by reducing the aircraft's body weight by using such lighter structures, the cost of fuel can be greatly reduced with the high jet fuel price for commercial airlines. However, these composites are prone to impact damage and the damage may occur without any observable sign on the surface, yet resulting in delaminations and disbonds that may occur well within the layers. We are studying the impact problem with carbon-fiber reinforced composite panels and developing SonicIR for this application as a fast and wide-area NDE technology. In this paper, we present our results in studying composite structures including carbon-fiber reinforced composite materials, and preliminary quantitative studies on delamination type defect depth identification in the panels.

  19. PREDICTION OF MODE Ⅰ CRACK PROPAGATION DIRECTION IN CARBON-FIBER REINFORCED COMPOSITE PLATE

    Institute of Scientific and Technical Information of China (English)

    张少琴; 杨维阳

    2004-01-01

    A newly developed Z fracture criterion for the composite materials was introduced,the new concepts of in-plane average strain,in-plane dilatational strain energy density factor and reciprocal characteristic function were presented.Many experimental results show that the Z fracture criterion can be well used to predict the crack propagating direction for mode Ⅰ crack in carbon-fiber reinforced composite laminates.

  20. Sodium sulfate corrosion of silicon carbide fiber-reinforced lithium aluminosilicate glass-ceramic matrix composites

    OpenAIRE

    1993-01-01

    Approved for public release; distribution is unlimited. Sodium sulfate hot corrosion of a SiC fiber-reinforced lithium aluminosilicate (LAS) glass-ceramic matrix composite was studied using Scanning Electron Microscope (SEM) and X-ray Diffraction (XRD). Changes in the microstructural chemical composition of the specimens were investigated. The samples provided by Naval Air Warfare Center (NAWC), Warminster, PA were grouped as follows: (1) as-received, (2) Na2SO4 salt-coated and heat-treate...

  1. Analysis and optimization of temperature distribution in carbon fiber reinforced composite materials during microwave curing process

    OpenAIRE

    2014-01-01

    Vacuum assisted microwave curing technologies and modified optical sensing systems have been employed to investigate the influence of ply orientation and thickness on through-thickness temperature distribution of carbon fiber reinforced composite laminates. Two different types of epoxy systems have been studied. The results demonstrated that the ply orientation did not affect the temperature distribution of composite materials. However, the thickness was an important influencing factor. Nearl...

  2. Smart damping of laminated fuzzy fiber reinforced composite shells using 1-3 piezoelectric composites

    Science.gov (United States)

    Kundalwal, S. I.; Kumar, R. Suresh; Ray, M. C.

    2013-10-01

    This paper deals with the investigation of active constrained layer damping (ACLD) of smart laminated continuous fuzzy fiber reinforced composite (FFRC) shells. The distinct constructional feature of a novel FFRC is that the uniformly spaced short carbon nanotubes (CNTs) are radially grown on the circumferential surfaces of the continuous carbon fiber reinforcements. The constraining layer of the ACLD treatment is considered to be made of vertically/obliquely reinforced 1-3 piezoelectric composite materials. A finite element (FE) model is developed for the laminated FFRC shells integrated with the two patches of the ACLD treatment to investigate the damping characteristics of the laminated FFRC shells. The effect of variation of the orientation angle of the piezoelectric fibers on the damping characteristics of the laminated FFRC shells has been studied when the piezoelectric fibers are coplanar with either of the two mutually orthogonal vertical planes of the piezoelectric composite layer. It is revealed that radial growth of CNTs on the circumferential surfaces of the carbon fibers enhances the attenuation of the amplitude of vibrations and the natural frequencies of the laminated FFRC shells over those of laminated base composite shells without CNTs.

  3. Processing and damage recovery of intrinsic self-healing glass fiber reinforced composites

    Science.gov (United States)

    Sordo, Federica; Michaud, Véronique

    2016-08-01

    Glass fiber reinforced composites with a self-healing, supramolecular hybrid network matrix were produced using a modified vacuum assisted resin infusion moulding process adapted to high temperature processing. The quality and fiber volume fraction (50%) of the obtained materials were assessed through microscopy and matrix burn-off methods. The thermo-mechanical properties were quantified by means of dynamic mechanical analysis, revealing very high damping properties compared to traditional epoxy-based glass fiber reinforced composites. Self-healing properties were assessed by three-point bending tests. A high recovery of the flexural properties, around 72% for the elastic modulus and 65% of the maximum flexural stress, was achieved after a resting period of 24 h at room temperature. Recovery after low velocity impact events was also visually observed. Applications for this intrinsic and autonomic self-healing highly reinforced composite material point towards semi-structural applications where high damping and/or integrity recovery after impact are required.

  4. Network model for thermal conductivities of unidirectional fiber-reinforced composites

    Science.gov (United States)

    Wang, Yang; Peng, Chaoyi; Zhang, Weihua

    2014-12-01

    An empirical network model has been developed to predict the in-plane thermal conductivities along arbitrary directions for unidirectional fiber-reinforced composites lamina. Measurements of thermal conductivities along different orientations were carried out. Good agreement was observed between values predicted by the network model and the experimental data; compared with the established analytical models, the newly proposed network model could give values with higher precision. Therefore, this network model is helpful to get a wider and more comprehensive understanding of heat transmission characteristics of fiber-reinforced composites and can be utilized as guidance to design and fabricate laminated composites with specific directional or specific locational thermal conductivities for structures that simultaneously perform mechanical and thermal functions, i.e. multifunctional structures (MFS).

  5. In vitro Study on Biodegradable AZ31 Magnesium Alloy Fibers Reinforced PLGA Composite

    Institute of Scientific and Technical Information of China (English)

    Y.H.Wu; N.Li; Y.Cheng; Y.F.Zheng; Y.Han

    2013-01-01

    AZ31 magnesium alloy fibers reinforced poly(lactic-co-glycolic acid) (PLGA) composites were prepared and their mechanical property,immersion corrosion behavior and biocompatibility were studied.The tensile test showed that with the addition of AZ31 fibers,the composites had a significant increment in tensile strength and elongation.For the direct cell attachment test,all the cells showed a healthy morphology and spread well on the experimental sample surfaces.The immersion results indicated that pH values of the immersion medium increased with increasing AZ31 fiber contents.All the in vitro experimental results indicated that this new kind of magnesium alloy fibers reinforced PLGA composites show a potential for future biomedical applications.

  6. Statistical Analysis of the Progressive Failure Behavior for Fiber-Reinforced Polymer Composites under Tensile Loading

    Directory of Open Access Journals (Sweden)

    Fang Wang

    2014-01-01

    Full Text Available An analytical approach with the help of numerical simulations based on the equivalent constraint model (ECM was proposed to investigate the progressive failure behavior of symmetric fiber-reinforced composite laminates damaged by transverse ply cracking. A fracture criterion was developed to describe the initiation and propagation of the transverse ply cracking. This work was also concerned with a statistical distributions of the critical fracture toughness values with due consideration given to the scale size effect. The Monte Carlo simulation technique coupled with statistical analysis was applied to study the progressive cracking behaviors of composite structures, by considering the effects of lamina properties and lay-up configurations. The results deduced from the numerical procedure were in good agreement with the experimental results obtained for laminated composites formed by unidirectional fiber reinforced laminae with different orientations.

  7. Influence of the curing cycles on the fatigue performance of unidirectional glass fiber reinforced epoxy composites

    DEFF Research Database (Denmark)

    Hüther, Jonas; Brøndsted, Povl

    2016-01-01

    stresses are built up and frozen, as residual stresses occur. In the present work, a glass fiber reinforced epoxy composite laminate with an unidirectional architecture based on non-crimp fabrics with backing fibers is investigated. Three different curing cycles (time-temperature cycles) are used, leading...... demonstrated that the resulting residual stresses barely influences the quasi-static mechanical properties of reinforced glass-fiber composites. It is found that the fatigue performance in the 0° direction is significantly influenced by the internal stresses, whereas the fatigue performance in the off axes......During the manufacturing process of fiber reinforced polymers the curing reaction of the resin results in shrinkage of the resin and introduces internal stresses in the composites. When curing at higher temperatures in order to shorten up the processing time, higher curing stresses and thermal...

  8. Development of a rapid design procedure for emergency repair of bridge columns using fiber-reinforced polymers

    OpenAIRE

    Slater, Susan E.

    2008-01-01

    Fiber reinforced polymers (FRP) are increasingly used for seismic retrofit of undamaged bridge columns. The addition of a confining jacket increases overall strength and ductility of the column. However, FRPs can also be used for repair of a damaged bridge column after a seismic event. This research project explores the application of FRPs for retrofit of damaged circular columns. A decision tree for the emergency repair of damaged columns is presented. The decision tree aids field engineers ...

  9. Seamless metal-clad fiber-reinforced organic matrix composite structures and process for their manufacture

    Science.gov (United States)

    Bluck, Raymond M. (Inventor); Bush, Harold G. (Inventor); Johnson, Robert R. (Inventor)

    1990-01-01

    A metallic outer sleeve is provided which is capable of enveloping a hollow metallic inner member having continuous reinforcing fibers attached to the distal end thereof. The inner member is then introduced into outer sleeve until inner member is completely enveloped by outer sleeve. A liquid matrix member is then injected into space between inner member and outer sleeve. A pressurized heat transfer medium is flowed through the inside of inner member, thereby forming a fiber reinforced matrix composite material. The wall thicknesses of both inner member and outer sleeve are then reduced to the appropriate size by chemical etching, to adjust the thermal expansion coefficient of the metal-clad composite structure to the desired value. thereby forming a fiber reinforced matrix composite material. The wall thicknesses of both inner member and outer sleeve are then reduced to the appropriate size by chemical etching, to adjust the thermal expansion coefficient of the metal-clad composite structure to the desired value. The novelty of this invention resides in the development of a efficient method of producing seamless metal clad fiber reinforced organic matrix composite structures.

  10. Carbon Fiber Reinforced Glass Matrix Composites for Space Based Applications.

    Science.gov (United States)

    1987-08-31

    composite plates were prepared using standard i, c-pressing procedures. The plates were cut into tensile specimens which were then subsequently notched...reinforced HMU composites were prepared using the matrix compositions and hot-pressing parameters shown in Table VI-1. The compositions are identical...shown in Figure VI-6. Traces of a- cristobalite are present in all three composites, with a noticeably larger amount present in the Nb20 5 composite. All

  11. Manufacturing Energy Intensity and Opportunity Analysis for Fiber-Reinforced Polymer Composites and Other Lightweight Materials

    Energy Technology Data Exchange (ETDEWEB)

    Liddell, Heather; Brueske, Sabine; Carpenter, Alberta; Cresko, Joseph

    2016-09-22

    With their high strength-to-weight ratios, fiber-reinforced polymer (FRP) composites are important materials for lightweighting in structural applications; however, manufacturing challenges such as low process throughput and poor quality control can lead to high costs and variable performance, limiting their use in commercial applications. One of the most significant challenges for advanced composite materials is their high manufacturing energy intensity. This study explored the energy intensities of two lightweight FRP composite materials (glass- and carbon-fiber-reinforced polymers), with three lightweight metals (aluminum, magnesium, and titanium) and structural steel (as a reference material) included for comparison. Energy consumption for current typical and state-of-the-art manufacturing processes were estimated for each material, deconstructing manufacturing process energy use by sub-process and manufacturing pathway in order to better understand the most energy intensive steps. Energy saving opportunities were identified and quantified for each production step based on a review of applied R&D technologies currently under development in order to estimate the practical minimum energy intensity. Results demonstrate that while carbon fiber reinforced polymer (CFRP) composites have the highest current manufacturing energy intensity of all materials considered, the large differences between current typical and state-of-the-art energy intensity levels (the 'current opportunity') and between state-of-the-art and practical minimum energy intensity levels (the 'R&D opportunity') suggest that large-scale energy savings are within reach.

  12. Bond Mechanisms in Fiber Reinforced Cement-Based Composites

    Science.gov (United States)

    1989-08-01

    Symposium on "Cement Based Composites: Bonding in Cementitious Composites," S. Mindess and S. Shah, Editors. 44. Nilson, A. H., "Bond Stress-Slip...Society Symposium on "Cement Based Composites: Bonding in Cementitious Composites," held in Boston, December 2 to 4, 1987, S. Mindess and S. Shah, 0

  13. Evaluation of test methods used to characterize fiber reinforced cementitious composites

    DEFF Research Database (Denmark)

    Paegle, Ieva; Fischer, Gregor

    2013-01-01

    of the tensile properties of Fiber Reinforced Cement Composites (FRCC) over the direct measurement of the tensile behavior because of the more convenient test setup and ease of specimen preparation. Three and four-point bending tests and round determinate panel test were carried out to evaluate the flexural...... and crack development has been quantitatively documented using a digital image correlation (DIC) system to investigate the validity of the commonly made assumptions....

  14. Space maintainer using fiber-reinforced composite and natural tooth--a non-invasive technique.

    Science.gov (United States)

    Tayab, Tabassum; Vizhi, Kayal; Srinivasan, Ila

    2011-04-01

    Dental traumatic injuries are widespread in the population and are a frequent pathology among children and teenagers. Dentists and especially pediatric dentists are commonly confronted with managing dental crown root fractures on a regular basis. Fiber-reinforced composite (FRC) have been used as an alternative to conventional space maintainers in pediatric dentistry. We present here a case of a 11-year-old boy with oblique crown root fracture, treated by placing extracted natural crown with FRC as space maintainer.

  15. Fiber-reinforced composite anterior bridge in pediatric traumatology: clinical considerations.

    Science.gov (United States)

    Chafaie, Amir; Dahan, Serge; Le Gall, Michel

    2013-12-01

    This article describes the protocol for creation of a fiber-reinforced composite bridge for temporary treatment of traumatic tooth loss affecting young adult dentition. This non-invasive solution is justified by the time lapse between the end of orthodontic treatment and the moment when the state of maturity of the various tissues makes it possible to install a conventional or implant-based prosthesis.

  16. Feasibility study of prestressed natural fiber-reinforced polylactic acid (pla) composite materials

    Science.gov (United States)

    Hinchcliffe, Sean A.

    The feasibility of manufacturing prestressed natural-fiber reinforced biopolymer composites is demonstrated in this work. The objective of this study was to illustrate that the specific mechanical properties of biopolymers can be enhanced by leveraging a combination of additive manufacturing (3D printing) and post-tensioning of continuous natural fiber reinforcement. Tensile and flexural PLA specimens were 3D-printed with and without post-tensioning ducts. The mechanical properties of reinforcing fibers jute and flax were characterized prior to post-tensioning. The effect of matrix cross-sectional geometry and post-tensioning on the specific mechanical properties of PLA were investigated using mechanical testing. Numerical and analytical models were developed to predict the experimental results, which confirm that 3D-printed matrices improve the specific mechanical properties of PLA composites and are further improved via initial fiber prestressing. The results suggest that both additive manufacturing and fiber prestressing represent viable new methods for improving the mechanical performance of natural fiber-reinforced polymeric composites.

  17. Evaluation of the Biocompatibility of New Fiber-Reinforced Composite Materials for Craniofacial Bone Reconstruction.

    Science.gov (United States)

    Lazar, Mădălina-Anca; Rotaru, Horaţiu; Bâldea, Ioana; Boşca, Adina B; Berce, Cristian P; Prejmerean, Cristina; Prodan, Doina; Câmpian, Radu S

    2016-10-01

    This study aims to assess the biocompatibility of new advanced fiber-reinforced composites (FRC) to be used for custom-made cranial implants. Four new formulations of FRC were obtained using polymeric matrices (combinations of monomers bisphenol A glycidylmethacrylate [bis-GMA], urethane dimethacrylate [UDMA], triethylene glycol dimethacrylate [TEGDMA], hydroxyethyl methacrylate [HEMA]) and E-glass fibers (300 g/mp). Every FRC contains 65% E-glass and 35% polymeric matrix. Composition of polymeric matrices are: bis-GMA (21%), TEGDMA (14%) for FRC1; bis-GMA (21%), HEMA (14%) for FRC2; bis-GMA (3.5%), UDMA (21%), TEGDMA (10.5%) for FRC3, and bis-GMA (3.5%), UDMA (21%), HEMA (10.5%) for FRC4. Cytotoxicity test was performed on both human dental pulp stem cells and dermal fibroblasts. Viability was assessed by tetrazolium dye colorimetric assay. Subcutaneous implantation test was carried out on 40 male Wistar rats, randomly divided into 4 groups, according to the FRC tested. Each group received subcutaneous dorsal implants. After 30 days, intensity of the inflammatory reaction, tissue repair status, and presence of the capsule were the main criteria assessed. Both cell populations showed no signs of cytotoxicity following the FRC exposures. In terms of cytotoxicity, the best results were obtained by FRC3 followed by FRC2, FRC4, and FRC1. FRC3 showed also the mildest inflammatory reaction and this correlated both with the noncytotoxic behavior and the presence of a well-organized capsule. The composite biomaterials developed may constitute an optimized alternative of the similar materials used for the reconstruction of craniofacial bone defects. According to authors' studies, the authors conclude that FRC3 is the best formulation regarding the biological behavior.

  18. Design and analysis of a novel latch system implementing fiber-reinforced composite materials

    Science.gov (United States)

    Guevara Arreola, Francisco Javier

    The use of fiber-reinforced composite materials have increased in the last four decades in high technology applications due to their exceptional mechanical properties and low weight. In the automotive industry carbon fiber have become popular exclusively in luxury cars because of its high cost. However, Carbon-glass hybrid composites offer an effective alternative to designers to implement fiber-reinforced composites into several conventional applications without a considerable price increase maintaining most of their mechanical properties. A door latch system is a complex mechanism that is under high loading conditions during car accidents such as side impacts and rollovers. Therefore, the Department of Transportation in The United States developed a series of tests that every door latch system comply in order to be installed in a vehicle. The implementation of fiber-reinforced composite materials in a door latch system was studied by analyzing the material behavior during the FMVSS No. 206 transverse test using computational efforts and experimental testing. Firstly, a computational model of the current forkbolt and detent structure was developed. Several efforts were conducted in order to create an effective and time efficient model. Two simplified models were implemented with two different contact interaction approaches. 9 composite materials were studied in forkbolt and 5 in detent including woven carbon fiber, unidirectional carbon fiber, woven carbon-glass fiber hybrid composites and unidirectional carbon-glass fiber hybrid composites. The computational model results showed that woven fiber-reinforced composite materials were stiffer than the unidirectional fiber-reinforced composite materials. For instance, a forkbolt made of woven carbon fibers was 20% stiffer than a forkbolt made of unidirectional fibers symmetrically stacked in 0° and 90° alternating directions. Furthermore, Hybrid composite materials behaved as expected in forkbolt noticing a decline

  19. Resin Matrix/Fiber Reinforced Composite Material,Ⅲ:Simulating Results

    Institute of Scientific and Technical Information of China (English)

    Li Chensha(李辰砂); Jiao Caishan; Liu Ying; Wang Zhengping; Wang Hongjie; Cao Maosheng

    2004-01-01

    According to the mathematical model which describes the curing process of composites constructed from continuous fiber-reinforced, thermosetting resin matrix prepreg materials, and the consolidation of the composite, the computer code calculates the data of the process variables of the flat-plate composites cured by a specified cure cycle, provides the variation of temperature distribution, the cure degree process, the resin variation and fibers stress inside the composite, the void variation and the residual stress distribution. The mechanism of curing process is illustrated and the cure cycle of composite material is optimized.

  20. Effect of silane activation on shear bond strength of fiber-reinforced composite post to resin cement

    OpenAIRE

    Kim, Hyun-Dong; Lee, Joo-Hee; Ahn, Kang-Min; Kim, Hee-Sun; Cha, Hyun-Suk

    2013-01-01

    PURPOSE Among the surface treatment methods suggested to enhance the adhesion of resin cement to fiber-reinforced composite posts, conflicting results have been obtained with silanization. In this study, the effects of silanization, heat activation after silanization, on the bond strength between fiber-reinforced composite post and resin cement were determined. MATERIALS AND METHODS Six groups (n=7) were established to evaluate two types of fiber post (FRC Postec Plus, D.T. Light Post) and th...

  1. MECHANICAL AND THERMO–MECHANICAL PROPERTIES OF BI-DIRECTIONAL AND SHORT CARBON FIBER REINFORCED EPOXY COMPOSITES

    Directory of Open Access Journals (Sweden)

    G. AGARWAL

    2014-10-01

    Full Text Available This paper based on bidirectional and short carbon fiber reinforced epoxy composites reports the effect of fiber loading on physical, mechanical and thermo-mechanical properties respectively. The five different fiber loading, i.e., 10wt. %, 20wt. %, 30wt. %, 40wt. % and 50wt. % were taken for evaluating the above said properties. The physical and mechanical properties, i.e., hardness, tensile strength, flexural strength, inter-laminar shear strength and impact strength are determined to represent the behaviour of composite structures with that of fiber loading. Thermo-mechanical properties of the material are measured with the help of Dynamic Mechanical Analyser to measure the damping capacity of the material that is used to reduce the vibrations. The effect of storage modulus, loss modulus and tan delta with temperature are determined. Finally, Cole–Cole analysis is performed on both bidirectional and short carbon fiber reinforced epoxy composites to distinguish the material properties of either homogeneous or heterogeneous materials. The results show that with the increase in fiber loading the mechanical properties of bidirectional carbon fiber reinforced epoxy composites increases as compared to short carbon fiber reinforced epoxy composites except in case of hardness, short carbon fiber reinforced composites shows better results. Similarly, as far as Loss modulus, storage modulus is concerned bidirectional carbon fiber shows better damping behaviour than short carbon fiber reinforced composites.

  2. Behavior of Fiber-Reinforced Smart Soft Composite Actuators According to Material Composition

    Energy Technology Data Exchange (ETDEWEB)

    Han, Min-Woo; Kim, Hyung-Il; Song, Sung-Hyuk; Ahn, Sung-Hoon [Seoul Nat’l Univ., Seoul (Korea, Republic of)

    2017-02-15

    Fiber-reinforced polymer composites, which are made by combining a continuous fiber that acts as reinforcement and a homogeneous polymeric material that acts as a host, are engineering materials with high strength and stiffness and a lightweight structure. In this study, a shape memory alloy(SMA) reinforced composite actuator is presented. This actuator is used to generate large deformations in single lightweight structures and can be used in applications requiring a high degree of adaptability to various external conditions. The proposed actuator consists of numerous individual laminas of the glass-fiber fabric that are embedded in a polymeric matrix. To characterize its deformation behavior, the composition of the actuator was changed by changing the matrix material and the number of the glass-fiber fabric layers. In addition, current of various magnitudes were applied to each actuator to study the effect of the heating of SMA wires on applying current.

  3. Fracture mechanics in fiber reinforced composite materials, taking as examples B/A1 and CRFP

    Science.gov (United States)

    Peters, P. W. M.

    1982-01-01

    The validity of linear elastic fracture mechanics and other fracture criteria was investigated with laminates of boron fiber reinforced aluminum (R/A1) and of carbon fiber reinforced epoxide (CFRP). Cracks are assessed by fracture strength Kc or Kmax (critical or maximum value of the stress intensity factor). The Whitney and Nuismer point stress criterion and average stress criterion often show that Kmax of fiber composite materials increases with increasing crack length; however, for R/A1 and CFRP the curve showing fracture strength as a function of crack length is only applicable in a small domain. For R/A1, the reason is clearly the extension of the plastic zone (or the damage zone n the case of CFRP) which cannot be described with a stress intensity factor.

  4. Mechanical Behavior of a Glass-fiber Reinforced Composite to Steel Joint for Ships

    Institute of Scientific and Technical Information of China (English)

    Xiaowen Li; Ping Li; Zhuang Lin; Dongmei Yang

    2015-01-01

    The use of a glass-fiber reinforced composite in marine structures is becoming more common, particularly due to the potential weight savings. The mechanical response of the joint between a glass-fiber reinforced polymer (GRP) superstructure and a steel hull formed is examined and subsequently modified to improve performance through a combined program of modeling and testing. A finite-element model is developed to predict the response of the joint. The model takes into account the contact at the interface between different materials, progressive damage, large deformation theory, and a non-linear stress-strain relationship. To predict the progressive failure, the analysis combines Hashin failure criteria and maximum stress failure criteria. The results show stress response has a great influence on the strength and bearing of the joint. The Balsawood-steel interface is proved to be critical to the mechanical behavior of the joint. Good agreement between experimental results and numerical predictions is observed.

  5. Processing of thermo-structural carbon-fiber reinforced carbon composites

    Directory of Open Access Journals (Sweden)

    Luiz Cláudio Pardini

    2009-06-01

    Full Text Available The present work describes the processes used to obtain thermostructural Carbon/Carbon composites. The processing of these materials begins with the definition of the architecture of the carbon fiber reinforcement, in the form of stacked plies or in the form of fabrics or multidirectional reinforcement. Incorporating fiber reinforcement into the carbon matrix, by filling the voids and interstices, leads to the densification of the material and a continuous increase in density. There are two principal processing routes for obtaining these materials: liquid phase processing and gas phase processing. In both cases, thermal processes lead to the formation of a carbon matrix with specific properties related to their precursor. These processes also differ in terms of yield. With liquid phase impregnation the yield is around 45 per cent, while gas phase processing yields around 15 per cent.

  6. DETERMINATION OF EFFECTIVE PROPERTIES OF FIBER-REINFORCED COMPOSITE LAMINATES

    Directory of Open Access Journals (Sweden)

    Andrzej Skrzat

    2014-06-01

    Full Text Available The determination of effective mechanical properties of multi-layer composite is presented in this paper. Computations based on finite element method predicting properties of inhomogeneous materials require solving huge tasks. More effective is Mori-Tanaka approach, typical for micromechanics problems. For regularly distributed fibers closed-forms for effective composite material properties are possible to derive. The results of homogenization are used in strength analysis of the composite pressure vessel.

  7. Interfacial fracture of dentin adhesively bonded to quartz-fiber reinforced composite

    Energy Technology Data Exchange (ETDEWEB)

    Melo, Renata M. [Department of Dental Materials and Pronsthodontics at Sao Jose dos Campos Dental Shool, Sao Paulo State University (UNESP), Sao Jose dos Campos, Sao Paulo 12245-820 (Brazil); Rahbar, Nima, E-mail: nrahbar@umassd.edu [Department of Civil and Environmental Engineering, University of Massachusetts Dartmouth, North Dartmouth, Massachusetts 02720 (United States); Soboyejo, Wole [Department of Mechanical and Aerospace Engineering, Princeton Institute of Science and Technology of Materials (PRISM), Princeton University, Princeton, New Jersey 08544 (United States)

    2011-05-10

    The paper presents the results of an experimental study of interfacial failure in a multilayered structure consisting of a dentin/resin cement/quartz-fiber reinforced composite (FRC). Slices of dentin close to the pulp chamber were sandwiched by two half-circle discs made of a quartz-fiber reinforced composite, bonded with bonding agent (All-bond 2, BISCO, Schaumburg) and resin cement (Duo-link, BISCO, Schaumburg) to make Brazil-nut sandwich specimens for interfacial toughness testing. Interfacial fracture toughness (strain energy release rate, G) was measured as a function of mode mixity by changing loading angles from 0 deg. to 15 deg. The interfacial fracture surfaces were then examined using Scanning Electron Microscopy (SEM) and Energy Dispersive X-ray Spectroscopy (EDX) to determine the failure modes when loading angles changed. A computational model was also developed to calculate the driving forces, stress intensity factors and mode mixities. Interfacial toughness increased from {approx} 1.5 to 3.2 J/m{sup 2} when the loading angle increases from {approx} 0 to 15 deg. The hybridized dentin/cement interface appeared to be tougher than the resin cement/quartz-fiber reinforced epoxy. The Brazil-nut sandwich specimen was a suitable method to investigate the mechanical integrity of dentin/cement/FRC interfaces.

  8. Solvent-based self-healing approaches for fiber-reinforced composites

    Science.gov (United States)

    Jones, Amanda R.

    Damage in composite materials spans many length scales and is often difficult to detect or costly to repair. The incorporation of self-healing functionality in composite materials has the potential to greatly extend material lifetime and reliability. Although there has been remarkable progress in self-healing polymers over the past decade, self-repair in fiber-reinforced composite materials presents significant technical challenges due to stringent manufacturing and performance requirements. For high performance, fiber-reinforced composites, the self-healing components need to survive high temperature processing, reside in matrix interstitial regions to retain a high fiber volume fraction, and have minimal impact on the mechanical properties of the host material. This dissertation explores several microencapsulated solvent-based self-healing approaches for fiber-reinforced composites at the fiber/ matrix interface size scale as well as matrix cracking. Systems are initially developed for room temperature cured epoxies/ glass fiber interfaces and successfully transitioned to carbon fibers and high temperature-cured, thermoplastic-toughened matrices. Full recovery of interfacial bond strength after complete fiber/matrix debonding is achieved with a microencapsulated solvent-based healing chemistry. The surface of a glass fiber is functionalized with microcapsules containing varying concentrations of reactive epoxy resin and ethyl phenyl acetate (EPA) solvent. Microbond specimens consisting of a single fiber and a microdroplet of epoxy are cured at 35°C, tested, and the interfacial shear strengths (IFSS) during the initial (virgin) debonding and subsequent healing events are measured. Debonding of the fiber/matrix interface ruptures the capsules, releasing resin and solvent into the crack plane. The solvent swells the matrix, initiating transport of residual amine functionality for further curing with the epoxy resin delivered to the crack plane. Using a resin

  9. Resin Matrix/Fiber Reinforced Composite Material, Ⅱ: Method of Solution and Computer Code

    Institute of Scientific and Technical Information of China (English)

    Li Chensha(李辰砂); Jiao Caishan; Liu Ying; Wang Zhengping; Wang Hongjie; Cao Maosheng

    2003-01-01

    According to a mathematical model which describes the curing process of composites constructed from continuous fiber-reinforced, thermosetting resin matrix prepreg materials, and the consolidation of the composites, the solution method to the model is made and a computer code is developed, which for flat-plate composites cured by a specified cure cycle, provides the variation of temperature distribution, the cure reaction process in the resin, the resin flow and fibers stress inside the composite, the void variation and the residual stress distribution.

  10. SERIAL SECTIONS THROUGH A CONTINUOUS FIBER-REINFORCED POLYMER COMPOSITE

    Directory of Open Access Journals (Sweden)

    Laurent Bizet

    2011-05-01

    Full Text Available The microstructure of a unidirectional glass-fiber composite material is described seeking especially for the influence of the stitching perpendicular to the reinforcement. Serial cuts are performed through the composite and the microstructure is quantified using global parameters and linear morphological analysis. A key result is that the stitching induces variations in fibers spacing within the yarns and in the matrix volume between the yarns. This can affect noticeably the flow of the resin during the manufacturing process and also the mechanical properties of the composite.

  11. Cellulose fiber reinforced nylon 6 or nylon 66 composites

    Science.gov (United States)

    Xu, Xiaolin

    Cellulose fiber was used to reinforce higher melting temperature engineering thermoplastics, such as nylon 6 and nylon 66. The continuous extrusion - direct compression molding processing and extrusion-injection molding were chosen to make cellulose fiber/nylon 6 or 66 composites. Tensile, flexural and Izod impact tests were used to demonstrate the mechanical properties of the composites. The continuous extrusion-compression molding processing can decrease the thermal degradation of cellulose fiber, but fiber doesn't disperse well with this procedure. Injection molding gave samples with better fiber dispersion and less void content, and thus gave better mechanical properties than compression molding. Low temperature compounding was used to extrude cellulose fiber/nylon composites. Plasticizer and a ceramic powder were used to decrease the processing temperature. Low temperature extrusion gave better mechanical properties than high temperature extrusion. The tensile modulus of nylon 6 composite with 30% fiber can reach 5GPa; with a tensile strength of 68MPa; a flexural modulus of 4GPa, and a flexural strength of 100MPa. The tensile modulus of nylon 66 composites with 30% fiber can reach 5GPa; with a flexural modulus of 5GPa; a tensile strength of 70MPa; and a flexural strength of 147MPa. The effect of thermal degradation on fiber properties was estimated. The Halpin-Tsai model and the Cox model were used to estimate the composite modulus. The Kelly-Tyson model was used to estimate the composite strength. The result indicates that the change of fiber properties determines the final properties of composites. Fiber length has a minor affect on both modulus and strength as long as the fiber length is above the critical length.

  12. Optimizing the delamination failure in bamboo fiber reinforced polyester composite

    Directory of Open Access Journals (Sweden)

    N. Abilash

    2016-01-01

    Full Text Available Delamination is represented to be the most prevalent failure in composite structures. The use of composites in the manufacturing sector plays a very important role in the industry in general. Moreover these materials have unique characteristics when analyzed separately from constituents which are a part of them. In this paper, a partially ecological composite was made, using natural fibers as reinforcement (bamboo fiber, in the polyester resin matrix to form a composite, seeking to improve the mechanical behavior among its class of materials. The characteristics of a composite material are determined by how it behaves while machining, Drilling is the most predominant machining process because of its cost effectiveness when compared with other processes. Obviously delamination is the major problem that is focused by many researchers while selecting drilling as the machining process in polymeric composites. This research mainly emphasizes on the critical parameters by varying its speed, feed, and diameter of the cutting tool, their contribution to delamination was analyzed. Reduced delaminations were identified by varying the speed and feed rate.

  13. Fabrication and Characterization of Multi-Walled Carbon Nanotube (MWCNT) and Ni-Coated Multi-Walled Carbon Nanotube (Ni-MWCNT) Repair Patches for Carbon Fiber Reinforced Composite Systems

    Science.gov (United States)

    Johnson, Brienne; Caraccio, Anne; Tate, LaNetra; Jackson, Dionne

    2011-01-01

    Multi-walled carbon nanotube (MWCNT)/epoxy and nickel-coated multi-walled carbon nanotube (Ni-MWCNT)/epoxy systems were fabricated into carbon fiber composite repair patches via vacuum resin infusion. Two 4 ply patches were manufactured with fiber orientations of [90/ 90/ 4590] and [0/90/ +45/ -45]. Prior to resin infusion, the MWCNT/Epoxy system and NiMWCNT/ epoxy systems were optimized for dispersion quality. Scanning electron microscopy (SEM) and optical microscopy (OM) were used to determine the presence ofcarbon nanotubes and assess dispersion quality. Decomposition temperatures were determined via thermogravametric analysis (TGA). SEM and TGA were also used to evaluate the composite repair patches.

  14. Liquid composite molding-processing and characterization of fiber-reinforced composites modified with carbon nanotubes

    Science.gov (United States)

    Zeiler, R.; Khalid, U.; Kuttner, C.; Kothmann, M.; Dijkstra, D. J.; Fery, A.; Altstädt, V.

    2014-05-01

    The increasing demand in fiber-reinforced plastics (FRPs) necessitates economic processing of high quality, like the vacuum-assisted resin transfer molding (VARTM) process. FRPs exhibit excellent in-plane properties but weaknesses in off-plane direction. The addition of nanofillers into the resinous matrix phase embodies a promising approach due to benefits of the nano-scaled size of the filler, especially its high surface and interface areas. Carbon nanotubes (CNTs) are preferable candidates for resin modification in regard of their excellent mechanical properties and high aspect ratios. However, especially the high aspect ratios give rise to withholding or filtering by fibrous fabrics during the impregnation process, i.e. length dependent withholding of tubes (short tubes pass through the fabric, while long tubes are restrained) and a decrease in the local CNT content in the laminate along the flow path can occur. In this study, hybrid composites containing endless glass fiber reinforcement and surface functionalized CNTs dispersed in the matrix phase were produced by VARTM. New methodologies for the quantification of the filtering of CNTs were developed and applied to test laminates. As a first step, a method to analyze the CNT length distribution before and after injection was established for thermosetting composites to characterize length dependent withholding of nanotubes. The used glass fiber fabric showed no perceptible length dependent retaining of CNTs. Afterward, the resulting test laminates were examined by Raman spectroscopy and compared to reference samples of known CNT content. This Raman based technique was developed further to assess the quality of the impregnation process and to quantitatively follow the local CNT content along the injection flow in cured composites. A local decline in CNT content of approx. 20% was observed. These methodologies allow for the quality control of the filler content and size-distribution in CNT based hybrid

  15. Nano-Fiber Reinforced Enhancements in Composite Polymer Matrices

    Science.gov (United States)

    Chamis, Christos C.

    2009-01-01

    Nano-fibers are used to reinforce polymer matrices to enhance the matrix dependent properties that are subsequently used in conventional structural composites. A quasi isotropic configuration is used in arranging like nano-fibers through the thickness to ascertain equiaxial enhanced matrix behavior. The nano-fiber volume ratios are used to obtain the enhanced matrix strength properties for 0.01,0.03, and 0.05 nano-fiber volume rates. These enhanced nano-fiber matrices are used with conventional fiber volume ratios of 0.3 and 0.5 to obtain the composite properties. Results show that nano-fiber enhanced matrices of higher than 0.3 nano-fiber volume ratio are degrading the composite properties.

  16. Modal analysis of additive manufactured carbon fiber reinforced polymer composite framework: Experiment and modeling

    Science.gov (United States)

    Dryginin, N. V.; Krasnoveikin, V. A.; Filippov, A. V.; Tarasov, S. Yu.; Rubtsov, V. E.

    2016-11-01

    Additive manufacturing by 3D printing is the most advanced and promising trend for making the multicomponent composites. Polymer-based carbon fiber reinforced composites demonstrate high mechanical properties combined with low weight characteristics of the component. This paper shows the results of 3D modeling and experimental modal analysis on a polymer composite framework obtained using additive manufacturing. By the example of three oscillation modes it was shown the agreement between the results of modeling and experimental modal analysis with the use of laser Doppler vibrometry.

  17. Experimental determination of optimum dielectric strength of Turmeric fiber reinforced polyester composites using flexural properties

    Directory of Open Access Journals (Sweden)

    K. Murali Mohan Rao

    2009-10-01

    Full Text Available The present investigation puts forward new natural fiber turmeric to be used in the preparation of turmeric fiber reinforced polyester (FRP composites. The dielectric strength of the composites shown decrease in trend with increase in volume fraction of fiber with appreciable reduction in their weight. There was clear fall in the density of the composites with increase in fiber volume fraction. The optimum value of dielectric strength was determined with flexural strength, flexural modulus and specific flexural strength, specific flexural modulus against percentage volume fraction of fiber from the graphs.

  18. Statistical modelling of compression and fatigue damage of unidirectional fiber reinforced composites

    DEFF Research Database (Denmark)

    Mishnaevsky, Leon; Brøndsted, Povl

    2009-01-01

    A statistical computational model of strength and damage of unidirectional carbon fiber reinforced composites under compressive and cyclic compressive loading is presented in this paper. The model is developed on the basis of the Budiansky–Fleck fiber kinking condition, continuum damage mechanics...... concept and the Monte-Carlo method. The effects of fiber misalignment variability, fiber clustering, load sharing rules on the damage in composite are studied numerically. It is demonstrated that the clustering of fibers has a negative effect of the damage resistance of a composite. Further, the static...

  19. Impacts of Temperature Disparity on Surface Modification of Short Jute Fiber-Reinforced Epoxy Composites

    Science.gov (United States)

    Basak, Reshmi; Choudhury, P. L.; Pandey, K. M.

    2017-08-01

    Chase for manufacturing composite materials without negotiating on the physio-mechanical performance has been prevailing since long. Short jute fiber-reinforced epoxy based composites are prepared and their mechanical properties have been analyzed. The fibers are peroxide-silane treated under varying conditions of temperature from low to high. Results display that the jute composites set at higher temperature values indicate higher values of mechanical properties compared to those synthesized under lower temperature range. The same can be cited for liquid retaining capacity.

  20. Flexural analysis of palm fiber reinforced hybrid polymer matrix composite

    Science.gov (United States)

    Venkatachalam, G.; Gautham Shankar, A.; Raghav, Dasarath; Santhosh Kiran, R.; Mahesh, Bhargav; Kumar, Krishna

    2015-07-01

    Uncertainty in availability of fossil fuels in the future and global warming increased the need for more environment friendly materials. In this work, an attempt is made to fabricate a hybrid polymer matrix composite. The blend is a mixture of General Purpose Resin and Cashew Nut Shell Liquid, a natural resin extracted from cashew plant. Palm fiber, which has high strength, is used as reinforcement material. The fiber is treated with alkali (NaOH) solution to increase its strength and adhesiveness. Parametric study of flexure strength is carried out by varying alkali concentration, duration of alkali treatment and fiber volume. Taguchi L9 Orthogonal array is followed in the design of experiments procedure for simplification. With the help of ANOVA technique, regression equations are obtained which gives the level of influence of each parameter on the flexure strength of the composite.

  1. Fiber-Reinforced Reactive Nano-Epoxy Composites

    Science.gov (United States)

    Zhong, Wei-Hong

    2011-01-01

    An ultra-high-molecular-weight polyethylene/ matrix interface based on the fabrication of a reactive nano-epoxy matrix with lower surface energy has been improved. Enhanced mechanical properties versus pure epoxy on a three-point bend test include: strength (25 percent), modulus (20 percent), and toughness (30 percent). Increased thermal properties include higher Tg (glass transition temperature) and stable CTE (coefficient of thermal expansion). Improved processability for manufacturing composites includes faster wetting rates on macro-fiber surfaces, lower viscosity, better resin infusion rates, and improved rheological properties. Improved interfacial adhesion properties with Spectra fibers by pullout tests include initial debonding force of 35 percent, a maximum pullout force of 25 percent, and energy to debond at 65 percent. Improved mechanical properties of Spectra fiber composites (tensile) aging resistance properties include hygrothermal effects. With this innovation, high-performance composites have been created, including carbon fibers/nano-epoxy, glass fibers/nano-epoxy, aramid fibers/ nano-epoxy, and ultra-high-molecularweight polyethylene fiber (UHMWPE).

  2. Residual stresses in shape memory alloy fiber reinforced aluminium matrix composite

    Science.gov (United States)

    Tsz Loong, Tang; Jamian, Saifulnizan; Ismail, Al Emran; Nur, Nik Hisyammudin Muhd; Watanabe, Yoshimi

    2017-01-01

    Process-induced residual stress in shape memory alloy (SMA) fiber reinforced aluminum (Al) matrix composite was simulated by ANSYS APDL. The manufacturing process of the composite named as NiTi/Al is start with loading and unloading process of nickel titanium (NiTi) wire as SMA to generate a residual plastic strain. Then, this plastic deformed NiTi wire would be embedded into Al to become a composite. Lastly, the composite is heated form 289 K to 363 K and then cooled back to 300 K. Residual stress is generated in composite because of shape memory effect of NiTi and mismatch of thermal coefficient between NiTi wire and Al matrix of composite. ANSYS APDL has been used to simulate the distribution of residual stress and strain in this process. A sensitivity test has been done to determine the optimum number of nodes and elements used. Hence, the number of nodes and elements used are 15680 and 13680, respectively. Furthermore, the distribution of residual stress and strain of nickel fiber reinforced aluminium matrix composite (Ni/Al) and titanium fiber reinforced aluminium matrix composite (Ti/Al) under same simulation process also has been simulated by ANSYS APDL as comparison to NiTi/Al. The simulation results show that compressive residual stress is generated on Al matrix of Ni/Al, Ti/Al and NiTi/Al during heating and cooling process. Besides that, they also have similar trend of residual stress distribution but difference in term of value. For Ni/Al and Ti/Al, they are 0.4% difference on their maximum compressive residual stress at 363K. At same circumstance, NiTi/Al has higher residual stress value which is about 425% higher than Ni/Al and Ti/Al composite. This implies that shape memory effect of NiTi fiber reinforced in composite able to generated higher compressive residual stress in Al matrix, hence able to enhance tensile property of the composite.

  3. Adherence of Streptococcus mutans to Fiber-Reinforced Filling Composite and Conventional Restorative Materials.

    Science.gov (United States)

    Lassila, Lippo V J; Garoushi, Sufyan; Tanner, Johanna; Vallittu, Pekka K; Söderling, Eva

    2009-12-04

    OBJECTIVES.: The aim was to investigate the adhesion of Streptococcus mutans (S. mutans) to a short glass fibers reinforced semi-IPN polymer matrix composite resin. The effect of surface roughness on adhesion was also studied. For comparison, different commercial restorative materials were also evaluated. MATERIALS AND METHODS.: Experimental composite FC resin was prepared by mixing 22.5 wt% of short E-glass fibers, 22.5 wt% of IPN-resin and 55 wt% of silane treated silica fillers using high speed mixing machine. Three direct composite resins (Z250, Grandio and Nulite), resin-modified glass ionomers (Fuji II LC), amalgam (ANA 2000), fiber-reinforced composite (FRC) (everStick and Ribbond), and pre-fabricated ceramic filling insert (Cerana class 1) were tested in this study. Enamel and dentin were used as controls. The specimens (n=3/group) with or without saliva were incubated in a suspension of S. mutans allowing initial adhesion to occur. For the enumeration of cells on the disc surfaces as colony forming units (CFU) the vials with the microbe samples were thoroughly Vortex-treated and after serial dilutions grown anaerobically for 2 days at +37 degrees C on Mitis salivarius agars (Difco) containing bacitracin. Bacterial adhesion was also evaluated by using scanning electron microscopy. Surface roughness (Ra) of the materials was also determined using a surface profilometer. All results were statistically analyzed with one-way analysis of variance (ANOVA). RESULTS.: Composite FC resin and other commercial restorative materials showed similar adhesion of S. mutans, while adhesion to dentin and enamel was significantly higher (p<0.05). Surface roughness had no effect on bacterial adhesion. Saliva coating significantly decreased the adhesion for all materials (p<0.05). Composite FC resin had a significantly higher Ra value than control groups (p<0.05). CONCLUSIONS.: Short fiber-reinforced composite with semi-IPN polymer matrix revealed similar S. mutans adhesion

  4. Impact test on natural fiber reinforced polymer composite materials

    Directory of Open Access Journals (Sweden)

    D. Chandramohan

    2013-06-01

    Full Text Available In this research, natural fibers like Sisal (Agave sisalana, Banana (Musa sepientum & Roselle (Hibiscus sabdariffa , Sisal and banana (hybrid , Roselle and banana (hybrid and Roselle and sisal (hybrid are fabricated with bio epoxy resin using molding method. In this work, impact strength of Sisal and banana (hybrid, Roselle and banana (hybridand Roselle and sisal (hybrid composite at dry and wet conditions were studied. Impact test were conducted izod impact testing machine. In this work micro structure of the specimens are scanned by the Scanning Electron Microscope.

  5. Electrospun carbon nanofibers for improved electrical conductivity of fiber reinforced composites

    Science.gov (United States)

    Alarifi, Ibrahim M.; Alharbi, Abdulaziz; Khan, Waseem S.; Asmatulu, Ramazan

    2015-04-01

    Polyacrylonitrile (PAN) was dissolved in dimethylformamide (DMF), and then electrospun to generate nanofibers using various electrospinning conditions, such as pump speeds, DC voltages and tip-to-collector distances. The produced nanofibers were oxidized at 270 °C for 1 hr, and then carbonized at 850 °C in an argon gas for additional 1 hr. The resultant carbonized PAN nanofibers were placed on top of the pre-preg carbon fiber composites as top layers prior to the vacuum oven curing following the pre-preg composite curing procedures. The major purpose of this study is to determine if the carbonized nanofibers on the fiber reinforced composites can detect the structural defects on the composite, which may be useful for the structural health monitoring (SHM) of the composites. Scanning electron microscopy images showed that the electrospun PAN fibers were well integrated on the pre-preg composites. Electrical conductivity studies under various tensile loads revealed that nanoscale carbon fibers on the fiber reinforced composites detected small changes of loads by changing the resistance values. Electrically conductive composite manufacturing can have huge benefits over the conventional composites primarily used for the military and civilian aircraft and wind turbine blades.

  6. Study of erosion characterization of carbon fiber reinforced composite material

    Science.gov (United States)

    Debnath, Uttam Kumar; Chowdhury, Mohammad Asaduzzaman; Kowser, Md. Arefin; Mia, Md. Shahin

    2017-06-01

    Carbon fiber composite materials are widely used at different engineering and industrial applications there are good physical, mechanical, chemical properties and light weight. Erosion behavior of materials depends on various factors such as impact angle, particle velocity, particle size, particle shape, particle type, particle flux, temperature of the tested materials. Among these factors impact angle and particle velocity have been recognized as two parameters that noticeably influence the erosion rates of all tested materials. Irregular shaped sand (SiO2) particles of various sizes (200-300 µm, 400-500 µm, and 500-600 µm) were selected erosive element. Tested conditions such as impingement angles between 15 degree to 90 degree, impact velocities between 30-50 m/sec, and stand-off distances 15-25 mm at surrounding room temperature were maintained. The highest level of erosion of the tested composite is obtained at 60° impact angle, which signifies the semi-ductile behavior of this material. Erosion showed increasing trend with impact velocity and decreasing nature in relation to stand-off distance. Surface damage was analyzed using SEM to examine the nature of the erosive wear mechanism.

  7. Piezoresistivity in Carbon Fiber Reinforced Cement Based Composites

    Institute of Scientific and Technical Information of China (English)

    Bing CHEN; Keru WU; Wu YAO

    2004-01-01

    The resu lts of some i nteresti ng investigation on the piezoresistivity of ca rbon fi ber reinforced cement based com posites (CFRC) are presented with the prospect of developing a new nondestructive testing method to assess the integrity of the composite. The addition of short carbon fibers to cement-based mortar or concrete improves the structural performance and at the same time significantly decreases the bulk electrical resistivity. This makes CFRC responsive to the smart behavior by measuring the resistance change with uniaxial pressure. The piezoresistivity of CFRC under different stress was studied, at the same time the damage occurring inner specimens was detected by acoustic emission as well. Test results show that there exists a marking pressure dependence of the conductivity in CFRC, in which the so-called negative pressure coefficient of resistive (NPCR) and positive pressure coefficient of resistive (PPCR) are observed under low and high pressure. Under constant pressures, time-dependent resistivity is an outstanding characteristic for the composites, which is defined as resistance creep. The breakdown and rebuild-up process of conductive network under pressure may be responsible for the pressure dependence of resistivity.

  8. Natural-fiber-reinforced polymer composites in automotive applications

    Science.gov (United States)

    Holbery, James; Houston, Dan

    2006-11-01

    In the past decade, natural-fiber composites with thermoplastic and thermoset matrices have been embraced by European car manufacturers and suppliers for door panels, seat backs, headliners, package trays, dashboards, and interior parts. Natural fibers such as kenaf, hemp, flax, jute, and sisal offer such benefits as reductions in weight, cost, and CO2, less reliance on foreign oil sources, and recyclability. However, several major technical considerations must be addressed before the engineering, scientific, and commercial communities gain the confidence to enable wide-scale acceptance, particularly in exterior parts where a Class A surface finish is required. Challenges include the homogenization of the fiber's properties and a full understanding of the degree of polymerization and crystallization, adhesion between the fiber and matrix, moisture repellence, and flame-retardant properties, to name but a few.

  9. In situ cure monitoring of advanced fiber reinforced composites

    Science.gov (United States)

    Powell, Graham R.; Crosby, Peter A.; Fernando, Gerard F.; France, Chris M.; Spooncer, Ronald C.; Waters, David N.

    1995-04-01

    This paper describes a comparative study of in-situ cure monitoring and cure modelling by three methods: (a) evanescent wave spectroscopy, (b) refractive index change, (c) near- infrared spectroscopy. Optical fibers were embedded into aerospace epoxy resins during the manufacturing process of the composite. The cure characteristics were then tracked in real- time during the processing of the material via evanescent wave interaction. This technique is based upon monitoring of characteristic infrared absorption bands of the resin system to find the concentration of the epoxy and amine hardener as a function of cure time. Hence this technique is suitable for on-line process monitoring and optimization. Results obtained from the optical fiber sensors were used to model the curing behavior of the resin system. The results were compared with near-infrared spectroscopy and differential scanning calorimetry experiments carried out under similar conditions. The feasibility of utilizing refractive index changes to monitor the extent of cure has also been demonstrated.

  10. Effects of Fiber Reinforcement on Clay Aerogel Composites

    Directory of Open Access Journals (Sweden)

    Katherine A. Finlay

    2015-08-01

    Full Text Available Novel, low density structures which combine biologically-based fibers with clay aerogels are produced in an environmentally benign manner using water as solvent, and no additional processing chemicals. Three different reinforcing fibers, silk, soy silk, and hemp, are evaluated in combination with poly(vinyl alcohol matrix polymer combined with montmorillonite clay. The mechanical properties of the aerogels are demonstrated to increase with reinforcing fiber length, in each case limited by a critical fiber length, beyond which mechanical properties decline due to maldistribution of filler, and disruption of the aerogel structure. Rather than the classical model for reinforced composite properties, the chemical compatibility of reinforcing fibers with the polymer/clay matrix dominated mechanical performance, along with the tendencies of the fibers to kink under compression.

  11. Mechanical Behavior of Hybrid Glass/Steel Fiber Reinforced Epoxy Composites

    Directory of Open Access Journals (Sweden)

    Amanda K. McBride

    2017-04-01

    Full Text Available While conventional fiber-reinforced polymer composites offer high strength and stiffness, they lack ductility and the ability to absorb energy before failure. This work investigates hybrid fiber composites for structural applications comprised of polymer, steel fiber, and glass fibers to address this shortcoming. Varying volume fractions of thin, ductile steel fibers were introduced into glass fiber reinforced epoxy composites. Non-hybrid and hybrid composite specimens were prepared and subjected to monolithic and half-cyclic tensile testing to obtain stress-strain relationships, hysteresis behavior, and insight into failure mechanisms. Open-hole testing was used to assess the vulnerability of the composites to stress concentration. Incorporating steel fibers into glass/epoxy composites offered a significant improvement in energy absorption prior to failure and material re-centering capabilities. It was found that a lower percentage of steel fibers (8.2% in the hybrid composite outperformed those with higher percentages (15.7% and 22.8% in terms of energy absorption and re-centering, as the glass reinforcement distributed the plasticity over a larger area. A bilinear hysteresis model was developed to predict cyclic behavior of the hybrid composite.

  12. Oxidation Behavior of Carbon Fiber-Reinforced Composites

    Science.gov (United States)

    Sullivan, Roy M.

    2008-01-01

    OXIMAP is a numerical (FEA-based) solution tool capable of calculating the carbon fiber and fiber coating oxidation patterns within any arbitrarily shaped carbon silicon carbide composite structure as a function of time, temperature, and the environmental oxygen partial pressure. The mathematical formulation is derived from the mechanics of the flow of ideal gases through a chemically reacting, porous solid. The result of the formulation is a set of two coupled, non-linear differential equations written in terms of the oxidant and oxide partial pressures. The differential equations are solved simultaneously to obtain the partial vapor pressures of the oxidant and oxides as a function of the spatial location and time. The local rate of carbon oxidation is determined at each time step using the map of the local oxidant partial vapor pressure along with the Arrhenius rate equation. The non-linear differential equations are cast into matrix equations by applying the Bubnov-Galerkin weighted residual finite element method, allowing for the solution of the differential equations numerically.

  13. NUMERICAL SIMULATION OF 2D FIBER-REINFORCED COMPOSITES USING BOUNDARY ELEMENT METHOD

    Institute of Scientific and Technical Information of China (English)

    KONG Fan-zhong; ZHENG Xiao-ping; YAO Zhen-han

    2005-01-01

    The boundary element method was improved for the 2D elastic composites with randomly distributed inclusions. This problem can be reduced to a boundary integral equation for a multi-connected domain. Further, considering the matrices of the tractions and displacements for each group of the identical inclusion were the same, an effective computational scheme was designed, since the orders of the resulting matrix equations can be greatly reduced. Numerical examples indicate that this boundary element method scheme is more effective than the conventional multi-domain boundary element method for such a problem. The present scheme can be used to investigate the effective mechanical properties of the fiber-reinforced composites.

  14. Preparation and Performance of Continuous Glass Fiber Reinforced Polypropylene Composite Honeycomb Sandwich Panels

    Directory of Open Access Journals (Sweden)

    Chen Ke

    2016-01-01

    Full Text Available As the light-weight and high-strength thermoplastic composites, novel honeycomb sandwich panels were discussed in this paper: continuous glass fiber reinforced polypropylene (GF/PP laminated sheets were used as the surface and polypropylene (PP honeycomb was used as the core. The effects of honeycomb core’s height, thickness and aperture on the mechanical properties were analyzed in this paper. The composite honeycomb sandwich panels exhibited excellent bending strength at 37.6MPa and lateral pressure strength at 25.8MPa.

  15. Method of controlling a resin curing process. [for fiber reinforced composites

    Science.gov (United States)

    Webster, Charles Neal (Inventor); Scott, Robert O. (Inventor)

    1989-01-01

    The invention relates to an analytical technique for controlling the curing process of fiber-reinforced composite materials that are formed using thermosetting resins. The technique is the percent gel method and involves development of a time-to-gel equation as a function of temperature. From this equation a rate-of-gel equation is then determined, and a percent gel is calculated which is the product of rate-of-gel times time. Percent gel accounting is used to control the proper pressure application point in an autoclave cure process to achieve desired properties in a production composite part.

  16. Determination of Material Parameters for Microbuckling Analysis of Fiber Reinforced Polymer Matrix Composites

    Directory of Open Access Journals (Sweden)

    Romanowicz M.

    2015-05-01

    Full Text Available This research focuses on studying the effect of the constitutive law adopted for a matrix material on the compressive response of a unidirectional fiber reinforced polymer matrix composite. To investigate this effect, a periodic unit cell model of a unidirectional composite with an initial fiber waviness and inelastic behavior of the matrix was used. The sensitivity of the compressive strength to the hydrostatic pressure, the flow rule and the fiber misalignment angle were presented. The model was verified against an analytical solution and experimental data. Results of this study indicate that a micromechanical model with correctly identified material parameters provides a useful alternative to theoretical models and experimentation.

  17. Determination of Material Parameters for Microbuckling Analysis of Fiber Reinforced Polymer Matrix Composites

    Science.gov (United States)

    Romanowicz, M.

    2015-05-01

    This research focuses on studying the effect of the constitutive law adopted for a matrix material on the compressive response of a unidirectional fiber reinforced polymer matrix composite. To investigate this effect, a periodic unit cell model of a unidirectional composite with an initial fiber waviness and inelastic behavior of the matrix was used. The sensitivity of the compressive strength to the hydrostatic pressure, the flow rule and the fiber misalignment angle were presented. The model was verified against an analytical solution and experimental data. Results of this study indicate that a micromechanical model with correctly identified material parameters provides a useful alternative to theoretical models and experimentation.

  18. Modeling and mesoscopic damage constitutive relation of brittle short-fiber-reinforced composites

    Institute of Scientific and Technical Information of China (English)

    刘洪秋; 梁乃刚; 夏蒙棼

    1999-01-01

    Aimed at brittle composites reinforced by randomly distributed short-fibers with a relatively large aspect ratio, stiffness modulus and strength, a mesoscopic material model was proposed. Based on the statistical description,damage mechanisms, damage-induced anisotropy, damage rate effect and stress redistribution, the constitutive relation were derived. By taking glass fiber reinforced polypropylene polymers as an example, the effect of initial orientation distribution of fibers, damage-induced anisotropy, and damage-rate effect on macro-behaviors of composites were quantitatively analyzed. The theoretical predictions compared favorably with the experimental results.

  19. Low Cost Fabrication of Silicon Carbide Based Ceramics and Fiber Reinforced Composites

    Science.gov (United States)

    Singh, M.; Levine, S. R.

    1995-01-01

    A low cost processing technique called reaction forming for the fabrication of near-net and complex shaped components of silicon carbide based ceramics and composites is presented. This process consists of the production of a microporous carbon preform and subsequent infiltration with liquid silicon or silicon-refractory metal alloys. The microporous preforms are made by the pyrolysis of a polymerized resin mixture with very good control of pore volume and pore size thereby yielding materials with tailorable microstructure and composition. Mechanical properties (elastic modulus, flexural strength, and fracture toughness) of reaction-formed silicon carbide ceramics are presented. This processing approach is suitable for various kinds of reinforcements such as whiskers, particulates, fibers (tows, weaves, and filaments), and 3-D architectures. This approach has also been used to fabricate continuous silicon carbide fiber reinforced ceramic composites (CFCC's) with silicon carbide based matrices. Strong and tough composites with tailorable matrix microstructure and composition have been obtained. Microstructure and thermomechanical properties of a silicon carbide (SCS-6) fiber reinforced reaction-formed silicon carbide matrix composites are discussed.

  20. Mechanical Properties of Natural Jute Fabric/Jute Mat Fiber Reinforced Polymer Matrix Hybrid Composites

    Directory of Open Access Journals (Sweden)

    Elsayed A. Elbadry

    2012-01-01

    Full Text Available Recycled needle punched jute fiber mats as a first natural fiber reinforcement system and these jute mats used as a core needle punched with recycled jute fabric cloths as skin layers as a second natural fiber reinforcement system were used for unsaturated polyester matrix composites via modifying the hand lay-up technique with resin preimpregnation into the jute fiber in vacuum. The effect of skin jute fabric on the tensile and bending properties of jute mat composites was investigated for different fiber weight contents. Moreover, the notch sensitivity of these composites was also compared by using the characteristic distance do calculated by Finite Element Method (FEM. The results showed that the tensile and flexural properties of jute mat composites increased by increasing the fiber weight content and by adding the jute fabric as skin layers. On the other hand, by adding the skins, the characteristic distance decreased and, therefore, the notch sensitivity of the composites increased. The fracture behavior investigated by SEM showed that extensive fiber pull-out mechanism was revealed at the tension side of jute mat composites under the bending load and by adding the jute cloth, the failure mode of jute mat was changed to fiber bridge mechanism.

  1. Investigation on The Mechanical Properties of Banana Fiber Reinforced Polyester Composites

    Directory of Open Access Journals (Sweden)

    A.K.Chaitanya

    2016-09-01

    Full Text Available the interest in natural fiber-reinforced polymer composite materials is rapidly growing both in terms of their industrial applications and fundamental research. The natural fiber composites are more environmentally friendly, and their availability, renewability, low density, and price as well as satisfactory mechanical properties make them an attractive ecological alternative to glass, carbon and man-made fibers used for the manufacturing of composites. The main objective of this project is to investigate the effect of NaOH solution on the mechanical properties of Banana fiber in polyester composites. The composites have been made by with and without treatment of NaOH solution using polymer matrix using Banana fiber. Mechanical properties such as tensile, impact and bending strengths were Studied by Carrying out respective tests with varying weights of fiber (0.5, 1, 1.5 and 2 gm’s. The tensile, impact and bending Strength of Banana fiber reinforced composites with NaOH solution was found to be increased when compared with without NaOH solution by varying fiber content. The concentrated of NaOH solution (5% to water (for 1lit.

  2. Considerations regarding the volume fraction influence on the wear behavior of the fiber reinforced composite systems

    Science.gov (United States)

    Caliman, R.

    2017-08-01

    This paper contains an analysis of the factors that have an influence on the tribological characteristics of the composite material sintered with metal matrix reinforced with carbon fibers. These composites are used generally if it’s needed the wear resistant materials, whereas these composites have high specific strength in conjunction with a good corrosion resistance at low densities and some self-lubricating properties. Through the knowledge of the better tribological properties of the materials and their behavior to wear, can be generated by dry and the wet friction. Thus, where necessary the use of high temperature resistant material with low friction between the elements, carbon fiber composite materials are very suitable because they have: mechanical strength and good ductility, melting temperature on the higher values, higher electrical and thermal conductivity, lower wear speed and lower friction forces. For this purpose, this paper also contains an experimental program based on the evidence of formaldehyde resin made from fiber reinforced Cu-carbon with the aim to specifically determine the volume of fibers fraction for the consolidation of the composite material. In order to determine the friction coefficient and the wear rates of the various fiber reinforced polymer mixtures of carbon have been used special devices with needle-type with steel disc. These tests were conducted in the atmosphere at the room temperature without external lubrication study taking into consideration the sliding different speeds with constant loading task.

  3. The Vibration Based Fatigue Damage Assessment of Steel and Steel Fiber Reinforced Concrete (SFRC Composite Girder

    Directory of Open Access Journals (Sweden)

    Xu Chen

    2015-01-01

    Full Text Available The steel-concrete composite girder has been usually applied in the bridge and building structures, mostly consisting of concrete slab, steel girder, and shear connector. The current fatigue damage assessment for the composite girder is largely based on the strain values and concrete crack features, which is time consuming and not stable. Hence the vibration-based fatigue damage assessment has been considered in this study. In detail, a steel-steel fiber reinforced concrete (SFRC composite girder was tested. The steel fiber reinforced concrete is usually considered for dealing with the concrete cracks in engineering practice. The composite girder was 3.3m long and 0.45m high. The fatigue load and impact excitation were applied on the specimen sequentially. According to the test results, the concrete crack development and global stiffness degradation during the fatigue test were relatively slow due to the favourable performance of SFRC in tension. But on the other hand, the vibration features varied significantly during the fatigue damage development. Generally, it confirmed the feasibility of executing fatigue damage assessment of composite bridge based on vibration method.

  4. Nondestructive Inspection of Thin Basalt Fiber Reinforced Composites Using Combined Terahertz Imaging and Infrared Thermography

    Directory of Open Access Journals (Sweden)

    Przemyslaw Lopato

    2016-01-01

    Full Text Available The inspection of thin basalt fiber reinforced composite materials was carried out using two nondestructive methods: terahertz time domain imaging and infrared thermography. In order to combine the information about the defects arising in examined materials the inspection results were parametrized. In order to acquire more information content, new approximation based features are proposed. Then, a knowledge extraction based multivariate analysis of preselected features’ vector was carried out. Finally, in order to integrate features distributions of representing different dynamic level of information, a multiresolution wavelet based data fusion algorithm was applied. The results are presented and discussed.

  5. Fiber reinforced composite loop space maintainer: An alternative to the conventional band and loop

    Directory of Open Access Journals (Sweden)

    Ramakrishna Yeluri

    2012-01-01

    Full Text Available The stainless steel band and loop appliance is the most commonly used fixed space maintainer in pediatric dentistry. But there are several disadvantages with this appliance such as the need for a cast or a working model, decalcification of the abutment tooth, loosening because of breakage or dissolution of the luting agent, tendency to get embedded in the soft tissue and the possibility of metal allergy. The purpose of this article is to present a simple, laboratory design of a "Fiber Reinforced Composite" (FRC loop space maintainer and discuss the advantages over the traditional band and loop space maintainers.

  6. Glass fiber-reinforced composite resin as a space maintainer: A clinical study

    OpenAIRE

    Subramaniam P; Babu GKL; Sunny R

    2008-01-01

    The aim of this study is to evaluate the use of glass fiber-reinforced composite resin (GFRCR) as a space maintainer and to compare it with a conventional band-and-loop space maintainer. A total of 30 children (23 boys and 7 girls) aged 6-8 years were selected for the study. Each of these children required maintenance of space due to premature loss of primary first molars in at least two quadrants. In one quadrant, a GFRCR space maintainer was applied and in the other quadrant a band-and-loop...

  7. Fiber reinforced composite loop space maintainer: An alternative to the conventional band and loop.

    Science.gov (United States)

    Yeluri, Ramakrishna; Munshi, Autar Krishen

    2012-04-01

    The stainless steel band and loop appliance is the most commonly used fixed space maintainer in pediatric dentistry. But there are several disadvantages with this appliance such as the need for a cast or a working model, decalcification of the abutment tooth, loosening because of breakage or dissolution of the luting agent, tendency to get embedded in the soft tissue and the possibility of metal allergy. The purpose of this article is to present a simple, laboratory design of a "Fiber Reinforced Composite" (FRC) loop space maintainer and discuss the advantages over the traditional band and loop space maintainers.

  8. Ultrasonic measurement of elastic constants in fiber-reinforced polymer composites under influence of absorbed moisture

    DEFF Research Database (Denmark)

    Nielsen, S.A.; Toftegaard, H.

    2000-01-01

    This paper presents an attempt to quantify hygral aging in fiber-reinforced polymer composites by the elastic constants C-11 and C-33. Quantitative ultrasonic measurements of the elastic constants for three different unidirectional as well as three different cross-ply specimens were compared....... The specimens were manufactured with different moisture resistant surfaces and immersed in water for 24 h. By calculating the elastic constants, it was taken into account that hygral aging was accompanied by absorption of moisture in the polymer matrix. Moisture changed the laminate dimensions significantly...

  9. Esthetic rehabilitation of severely decayed primary incisors using glass fiber reinforced composite: a case report.

    Science.gov (United States)

    Metha, Deepak; Gulati, Akanksha; Basappa, N; Raju, O S

    2012-01-01

    Restoration of primary maxillary incisors severely damaged by caries or trauma is a clinical challenge in pediatric dental clinics. Early childhood caries is observed in approximately half the child population. In the past, the only treatment option would have been to extract the affected teeth and replace them with prosthetic substitutes. With the introduction of new adhesive systems and restorative materials, alternative approaches in treating these teeth have been proposed. The purpose of this paper was to describe the rehabilitation of primary anterior teeth in a 5-year-old patient using glass fiber reinforced composite resin as an intracanal post.

  10. Fiber-reinforced Composite Resin Prosthesis to Restore Missing Posterior Teeth: A Case Report

    Directory of Open Access Journals (Sweden)

    Pekka Vallittu

    2007-01-01

    Full Text Available A fiber-reinforced composite inlay-onlay FPD was used for a single posterior tooth replacement in a patient refusing implant for psychological reasons. The FRC-FPD was made of pre-impregnated E-glass fibers (everStick, StickTeck, Turku, Finland embedded in a resin matrix (Stick Resin, StickTeck, Turku, Finland. The unidirectional glass fibers were used to make a framework structure with high volume design placed in the pontic (edentulous region. To reproduce the morphology of natural teeth, the framework structure was then veneered with Gradia (GC, Tokyo, Japan.

  11. An Inverse method of elastic constants for unidirectional fiber-reinforced composite plate

    Institute of Scientific and Technical Information of China (English)

    YANG Jing; CUI Lian-jun; XU Jian; CHENG Jian-chun

    2006-01-01

    An inverse method is presented to determine the elastic constants of an experimental sample,a titanium graphite unidirectional fiber-reinforced composite plate,using wavelet transform and neural networks.Optimal algorithms of wavelet transform and neural networks are given here in order to improve the accuracy of inversion results.Coherent results were shown in both fiber direction and cross fiber direction,proving the feasibility of this method.Neither the group velocity of the Lamb wave modes are needed,as in the conventional method,and no direct least-square fitting of the experimental waveforms is necessary.

  12. Evolution of the health of concrete structures by electrically conductive GFRP (glass fiber reinforced plastic) composites

    Science.gov (United States)

    Shin, Soon-Gi

    2002-02-01

    The function and performance of self-diagnostic composites embedded in concrete blocks and piles were investigated by bending tests and electrical resistance measurement. Carbon powder (CP) and carbon fiber (CF) were introduced into glass fiber reinforced plastic (GFRP) composites to provide electrical conductivity. The CPGFRP composite displays generally good performance in various bending tests of concrete block and piles compared to the CFGFRP composite. The electrical resistance of the CPGFRP composite increases remarkably at small strains in response to microcrack formation at about 200 μm strain, and can be used to detect smaller deformations before crack formation. The CPGFRP composite shows continuous change in resistance up to a large strain level just before the final fracture for concrete structures reinforced by steel bars. It is concluded that self-diagnostic composites can be used to predict damage and fracture in concrete blocks and piles.

  13. Bisphenyl-Polymer/Carbon-Fiber-Reinforced Composite Compared to Titanium Alloy Bone Implant

    Directory of Open Access Journals (Sweden)

    Richard C. Petersen

    2011-01-01

    Full Text Available Aerospace/aeronautical thermoset bisphenyl-polymer/carbon-fiber-reinforced composites are considered as new advanced materials to replace metal bone implants. In addition to well-recognized nonpolar chemistry with related bisphenol-polymer estrogenic factors, carbon-fiber-reinforced composites can offer densities and electrical conductivity/resistivity properties close to bone with strengths much higher than metals on a per-weight basis. In vivo bone-marrow tests with Sprague-Dawley rats revealed far-reaching significant osseoconductivity increases from bisphenyl-polymer/carbon-fiber composites when compared to state-of-the-art titanium-6-4 alloy controls. Midtibial percent bone area measured from the implant surface increased when comparing the titanium alloy to the polymer composite from 10.5% to 41.6% at 0.8 mm, P<10−4, and 19.3% to 77.7% at 0.1 mm, P<10−8. Carbon-fiber fragments planned to occur in the test designs, instead of producing an inflammation, stimulated bone formation and increased bone integration to the implant. In addition, low-thermal polymer processing allows incorporation of minerals and pharmaceuticals for future major tissue-engineering potential.

  14. Micromechanical Modeling of Fiber-Reinforced Composites with Statistically Equivalent Random Fiber Distribution

    Directory of Open Access Journals (Sweden)

    Wenzhi Wang

    2016-07-01

    Full Text Available Modeling the random fiber distribution of a fiber-reinforced composite is of great importance for studying the progressive failure behavior of the material on the micro scale. In this paper, we develop a new algorithm for generating random representative volume elements (RVEs with statistical equivalent fiber distribution against the actual material microstructure. The realistic statistical data is utilized as inputs of the new method, which is archived through implementation of the probability equations. Extensive statistical analysis is conducted to examine the capability of the proposed method and to compare it with existing methods. It is found that the proposed method presents a good match with experimental results in all aspects including the nearest neighbor distance, nearest neighbor orientation, Ripley’s K function, and the radial distribution function. Finite element analysis is presented to predict the effective elastic properties of a carbon/epoxy composite, to validate the generated random representative volume elements, and to provide insights of the effect of fiber distribution on the elastic properties. The present algorithm is shown to be highly accurate and can be used to generate statistically equivalent RVEs for not only fiber-reinforced composites but also other materials such as foam materials and particle-reinforced composites.

  15. The effect of exfoliated graphite on carbon fiber reinforced composites for cryogenic applications

    Science.gov (United States)

    McLaughlin, Adam Michael

    It is desirable to lighten cryogenic fuel tanks through the use of composites for the development of a reusable single stage launch vehicle. Conventional composites fall victim to microcracking due to the cyclic loading and temperature change experienced during launch and re-entry conditions. Also, the strength of a composite is generally limited by the properties of the matrix. The introduction of the nanoplatelet, exfoliated graphite or graphene, to the matrix shows promise of increasing both the microcracking resistivity and the mechanical characteristics. Several carbon fiber composite plates were manufactured with varying concentrations of graphene and tested under both room and cryogenic conditions to characterize graphene's effect on the composite. Results from tensile and fracture testing indicate that the ideal concentration of graphene in our carbon fiber reinforced polymer composites for cryogenic applications is 0.08% mass graphene.

  16. Effect of Fillers on E-Glass/Jute Fiber Reinforced Epoxy Composites

    Directory of Open Access Journals (Sweden)

    Sudeep Deshpande

    2014-08-01

    Full Text Available In this work, an investigation was carried out on E-glass fiber/jute fiber reinforced epoxy composites filled with varying concentrations of bone and coconut shell powder. The composites were fabricated by hand lay-up technique and the mechanical properties such as ultimate tensile strength, flexural strength, inter laminar shear strength (ILSS, tensile modulus, impact strength and hardness of the fabricated composites were tested. The test results of these were compared with unfilled HFRP composites. From the results it was found that the mechanical properties of the composites increased with the increase in filler content. Composites filled with 15% volume coconut shell powder exhibited maximum flexural strength, inter laminar shear strength (ILSS, tensile modulus and hardness. Maximum impact strength was achieved by addition of filler (15% Vol. of bone powder.

  17. Short Jute Fiber Reinforced Polypropylene Composites: Effect of Nonhalogenated Fire Retardants

    Directory of Open Access Journals (Sweden)

    Sk. Sharfuddin Chestee

    2017-01-01

    Full Text Available Short jute fiber reinforced polypropylene (PP composites were prepared using a single screw extrusion moulding. Jute fiber content in the composites is optimized with the extent of mechanical properties, and composites with 20% jute show higher mechanical properties. Dissimilar concentrations of several fire retardants (FRs, such as magnesium oxide (MO, aluminum oxide (AO, and phosphoric acid (PA, were used in the composites. The addition of MO, AO, and PA improved the fire retardancy properties (ignition time, flame height, and total firing time of the composites. Ignition time for 30% MO, flame height for 30% PA, and total firing time for 20% MO content composites showed good results which were 8 sec, 1 inch, and 268 sec, respectively. Mechanical properties (tensile strength, tensile modulus, bending strength, bending modulus, and elongation at break, degradation properties (soil test, weathering test, and percentage of weight loss, and water uptake were studied.

  18. Design and realization a skiff racing boat hull made of natural fibers reinforced composite

    Science.gov (United States)

    Collotta, M.; Solazzi, L.; Pandini, S.; Tomasoni, G.; Alberti, M.; Donzella, G.

    2016-05-01

    This paper discusses the development of a racing boat with an hull made of a composite material reinforced by natural fibers. In particular, we report here the design and realization of the boat hull, the assessment of its mechanical performance by means of a computer assisted simulation, and the cost analysis to assess the economic sustainability of the new composite developed. The results have shown that the new composite has a performance comparable with conventional glass fiber reinforced composites employed for the realization of this type of boat, accordingly to the technology employed and the lamination sequence adopted. Moreover, the FEM analysis performed over the skiff of the designed and constructed boat has demonstrated a successful choice of the material for real application, as it was later confirmed by the good performance of the boat in water. Finally, the cost analysis highlighted the economic sustainability of the new composite, allowing a cost saving of over 28% with respect to carbon fiber composites.

  19. Effect of Different Parameters on Mechanical and Erosion Wear Behavior of Bamboo Fiber Reinforced Epoxy Composites

    Directory of Open Access Journals (Sweden)

    Anu Gupta

    2011-01-01

    Full Text Available The application of natural fibers as reinforcement in polymer composites has been continuously growing during the last few decades. These composites find diverse applications in hostile environment where they are exposed to external attacks such as solid particle erosion. Also, in many respects, the mechanical properties of different polymer composites are their most important characteristics. Therefore, improvement of the erosion resistance and mechanical behavior of polymer composites are the prime requirements in their applications. Bamboo fiber which is rich in cellulose, relatively inexpensive, and abundantly available has the potential for reinforcement in polymers. To this end, an attempt has been made in this paper not only to study the utilization potential of bamboo fiber in polymer composites but also to study the effect of various parameters on mechanical and erosion wear performance of bamboo fiber reinforced epoxy composites.

  20. A Review on Natural Fiber Reinforced Polymer Composite and Its Applications

    Directory of Open Access Journals (Sweden)

    Layth Mohammed

    2015-01-01

    Full Text Available Natural fibers are getting attention from researchers and academician to utilize in polymer composites due to their ecofriendly nature and sustainability. The aim of this review article is to provide a comprehensive review of the foremost appropriate as well as widely used natural fiber reinforced polymer composites (NFPCs and their applications. In addition, it presents summary of various surface treatments applied to natural fibers and their effect on NFPCs properties. The properties of NFPCs vary with fiber type and fiber source as well as fiber structure. The effects of various chemical treatments on the mechanical and thermal properties of natural fibers reinforcements thermosetting and thermoplastics composites were studied. A number of drawbacks of NFPCs like higher water absorption, inferior fire resistance, and lower mechanical properties limited its applications. Impacts of chemical treatment on the water absorption, tribology, viscoelastic behavior, relaxation behavior, energy absorption flames retardancy, and biodegradability properties of NFPCs were also highlighted. The applications of NFPCs in automobile and construction industry and other applications are demonstrated. It concluded that chemical treatment of the natural fiber improved adhesion between the fiber surface and the polymer matrix which ultimately enhanced physicomechanical and thermochemical properties of the NFPCs.

  1. Physicochemical characterization of three fiber-reinforced epoxide-based composites for dental applications.

    Science.gov (United States)

    Bonon, Anderson J; Weck, Marcus; Bonfante, Estevam A; Coelho, Paulo G

    2016-12-01

    Fiber-reinforced composite (FRC) biomedical materials are in contact with living tissues arising biocompatibility questions regarding their chemical composition. The hazards of materials such as Bisphenol A (BPA), phthalate and other monomers and composites present in FRC have been rationalized due to its potential toxicity since its detection in food, blood, and saliva. This study characterized the physicochemical properties and degradation profiles of three different epoxide-based materials intended for restorative dental applications. Characterization was accomplished by several methods including FTIR, Raman, Brunauer-Emmett-Teller (BET) Analysis, X-ray fluorescence spectroscopy, and degradation experiments. Physicochemical characterization revealed that although materials presented similar chemical composition, variations between them were more largely accounted by the different phase distribution than chemical composition.

  2. Flexural, Impact Properties and Sem Analysis of Bamboo and Glass Fiber Reinforced Polyester Hybrid Composites

    Directory of Open Access Journals (Sweden)

    Raghavendra Rao. H

    2014-08-01

    Full Text Available The Flexural, Impact properties and Scanning electron microscope analysis of Bamboo/glass fibers Reinforced polyester Hybrid composites were studied. The effect of alkali treatment of the bamboo fibers on these properties was also studied. It was observed that the Flexural, impact properties of the hybrid composite increase with glass fiber content. These properties found to be higher when alkali treated bamboo fibers were used in the hybrid composites. The elimination of amorphous hemi-cellulose with alkali treated leading to higher crystallinity of the bamboo fibers with alkali treatment may be responsible for these observations. The author investigated the interfacial bonding between Glass/Bamboo reinforced polyester composites. The effect of alkali treatment on the bonding between Glass/Bamboo composites was also studied.

  3. Pembuatan Adhesive Bridge dengan Fiber Reinforced Composite untuk Perawatan Kehilangan dan Kegoyahan Gigi Anterior Rahang Bawah

    Directory of Open Access Journals (Sweden)

    Demmy Wijaya

    2014-06-01

    Full Text Available Salah satu perawatan kehilangan gigi anterior untuk tujuan estetis adalah dengan adhesive bridge. Fiber Reinforced Composite (FRC adalah bahan struktural yang terdiri dari 2 konstituen yang berbeda. Komponen penguat (fiber memberikan kekuatan dan kekakuan, sedangkan matriks (resin komposit mendukung penguatan. Bahan FRC dapat digunakan untuk pembuatan adhesive bridge dan juga dapat digunakan sebagai stabilisasi gigi yang mengalami kegoyahan. Adanya gigi pendukung yang sehat juga sangat membantu keberhasilan perawatan ini. Laporan kasus ini bertujuan untuk memberikan informasi tentang penatalaksanaan perawatan kehilangan dan kegoyahan gigi anterior rahang bawah menggunakan FRC. Seorang pasien laki-laki berusia 33 tahun datang ke klinik Prostodonsia RSGM Prof. Soedomo ingin dibuatkan gigi tiruan. Pasien kehilangan gigi 31, gigi 32, gigi 41 dan mengalami kegoyahan derajat 2 disertai resesi gingiva. Kondisi tersebut akibat pasca pembuatan gigi tiruan di tukang gigi. Pasien tidak ingin giginya yang goyah dilakukan pencabutan. Tatalaksana kasus: pencetakan rahang untuk model diagnostik, pembuatan mock-up pontik gigi 31 pada model diagnostik, pembuatan index dengan mencetak bagian lingual dan 1/3 incisal menggunakan putty, preparasi gigi penyangga (gigi 32, 33, 41, 42, 43, pemasangan fiber dengan bantuan index putty, pembentukan bagian labial pontik dengan komposit, finishing dan polishing. Kesimpulan: Fiber reinforced composite dapat dipakai untuk pengelolaan pasien yang mengalami kehilangan dan kegoyahan gigi anterior rahang bawah. Adhesive Bridge of Fiber Reinforced Composite to Treat Tooth Missing and Luxation of Lower Anterior Teeth. One of the anterior tooth loss treatments for esthetic purposes is the adhesive bridge. Fiber Reinforced Composite (FRC is a structural material that consists of two different constituencies. Amplifier components (fiber provide strength and stiffness, while matrix (resin composite support reinforcement. FRC materials

  4. Impact behavior of a SiC fiber-reinforced reaction bonded Si3N4 composite

    Science.gov (United States)

    Grady, J.; Bhatt, R.; Klima, S.

    1989-01-01

    Impact tests were performed on a series of ceramic plate specimens. Monolithic (unreinforced) and composite specimens with various fiber layups were tested to determine the effect that the fiber reinforcement has on impact damage initiation and dynamic response of the ceramic materials. Results show that a porous surface layer of Si3N4 on the composite specimens can enhance the energy absorbing capability of the composite specimens. The addition of SiC fiber reinforcement to the RBSN matrix material is also shown to significantly change the mode of failure and reduce the extent of damage due to impact.

  5. Modeling of Stress Development During Thermal Damage Healing in Fiber-reinforced Composite Materials Containing Embedded Shape Memory Alloy Wires

    NARCIS (Netherlands)

    Bor, Teunis Cornelis; Warnet, Laurent; Akkerman, Remko; de Boer, Andries

    2010-01-01

    Fiber-reinforced composite materials are susceptible to damage development through matrix cracking and delamination. This article concerns the use of shape memory alloy (SMA) wires embedded in a composite material to support healing of damage through a local heat treatment. The composite material

  6. Modeling of Stress Development During Thermal Damage Healing in Fiber-reinforced Composite Materials Containing Embedded Shape Memory Alloy Wires

    NARCIS (Netherlands)

    Bor, T.C.; Warnet, L.; Akkerman, R.; Boer, de A.

    2010-01-01

    Fiber-reinforced composite materials are susceptible to damage development through matrix cracking and delamination. This article concerns the use of shape memory alloy (SMA) wires embedded in a composite material to support healing of damage through a local heat treatment. The composite material co

  7. Tensile Properties of Surface-Treated Glass Fiber Reinforced PTFE Composite with Rare Earth Elements

    Institute of Scientific and Technical Information of China (English)

    薛玉君; 程先华

    2003-01-01

    The optimum amount of rare earth elements (RE) for treating glass fiber surface and its effect on the tensile properties of glass fiber reinforced polytetrafluoroethylene (GF/PTFE) composites were investigated. The tensile properties of GF/PTFE composites with different surface treatment conditions were measured. The fracture surface morphologies were observed and analyzed by SEM. The results indicate that rare earth elements can effectively promote the interfacial adhesion between the glass fiber and PTFE, owing to the effects of rare earth elements on the compatibility. The tensile properties of GF/PTFE composites can be improved considerably when the content of RE in surface modifier is 0.2%~0.4%, and the optimum performance of GF/PTFE composites is obtained at 0.3%RE content.

  8. Multiscale carbon nanotube-carbon fiber reinforcement for advanced epoxy composites.

    Science.gov (United States)

    Bekyarova, E; Thostenson, E T; Yu, A; Kim, H; Gao, J; Tang, J; Hahn, H T; Chou, T-W; Itkis, M E; Haddon, R C

    2007-03-27

    We report an approach to the development of advanced structural composites based on engineered multiscale carbon nanotube-carbon fiber reinforcement. Electrophoresis was utilized for the selective deposition of multi- and single-walled carbon nanotubes (CNTs) on woven carbon fabric. The CNT-coated carbon fabric panels were subsequently infiltrated with epoxy resin using vacuum-assisted resin transfer molding (VARTM) to fabricate multiscale hybrid composites in which the nanotubes were completely integrated into the fiber bundles and reinforced the matrix-rich regions. The carbon nanotube/carbon fabric/epoxy composites showed approximately 30% enhancement of the interlaminar shear strength as compared to that of carbon fiber/epoxy composites without carbon nanotubes and demonstrate significantly improved out-of-plane electrical conductivity.

  9. Rate dependent response and failure of a ductile epoxy and carbon fiber reinforced epoxy composite

    Energy Technology Data Exchange (ETDEWEB)

    Brown, Eric N [Los Alamos National Laboratory; Rae, Philip J [Los Alamos National Laboratory; Dattelbaum, Dana M [Los Alamos National Laboratory; Stahl, David B [Los Alamos National Laboratory

    2010-01-01

    An extensive characterization suite has been performed on the response and failure of a ductile epoxy 55A and uniaxial carbon fiber reinforced epoxy composite of IM7 fibers in 55A resin from the quasistatic to shock regime. The quasistatic and intermediate strain rate response, including elastic modulus, yield and failure have are characterized by quasistatic, SHPB, and DMA measurements as a function of fiber orientation and temperature. The high strain rate shock effect of fiber orientation in the composite and response of the pure resin are presented for plate impact experiments. It has previously been shown that at lower impact velocities the shock velocity is strongly dependent on fiber orientation but at higher impact velocity the in-plane and through thickness Hugoniots converge. The current results are compared with previous studies of the shock response of carbon fiber composites with more conventional brittle epoxy matrices. The spall response of the composite is measured and compared with quasistatic fracture toughness measurements.

  10. Mechanical properties, volumetric shrinkage and depth of cure of short fiber-reinforced resin composite.

    Science.gov (United States)

    Tsujimoto, Akimasa; Barkmeier, Wayne W; Takamizawa, Toshiki; Latta, Mark A; Miyazaki, Masashi

    2016-01-01

    The mechanical properties, volumetric shrinkage and depth of cure of a short fiber-reinforced resin composite (SFRC) were investigated in this study and compared to both a bulk fill resin composite (BFRC) and conventional glass/ceramic-filled resin composite (CGRC). Fracture toughness, flexural properties, volumetric shrinkage and depth of cure of the SFRC, BFRC and CGRC were measured. SFRC had significantly higher fracture toughness than BFRCs and CGRCs. The flexural properties of SFRC were comparable with BFRCs and CGRCs. SFRC showed significantly lower volumetric shrinkage than the other tested resin composites. The depth of cure of the SFRC was similar to BFRCs and higher than CGRCs. The data from this laboratory investigation suggests that SFRC exhibits improvements in fracture toughness, volumetric shrinkage and depth of cure when compared with CGRC, but depth of cure of SFRC was similar to BFRC.

  11. Solid Particle Erosion of Date Palm Leaf Fiber Reinforced Polyvinyl Alcohol Composites

    Directory of Open Access Journals (Sweden)

    Jyoti R. Mohanty

    2014-01-01

    Full Text Available Solid particle erosion behavior of short date palm leaf (DPL fiber reinforced polyvinyl alcohol (PVA composite has been studied using silica sand particles (200 ± 50 μm as an erodent at different impingement angles (15–90° and impact velocities (48–109 m/s. The influence of fiber content (wt% of DPL fiber on erosion rate of PVA/DPL composite has also been investigated. The neat PVA shows maximum erosion rate at 30° impingement angle whereas PVA/DPL composites exhibit maximum erosion rate at 45° impingement angle irrespective of fiber loading showing semiductile behavior. The erosion efficiency of PVA and its composites varies from 0.735 to 16.289% for different impact velocities studied. The eroded surfaces were observed under scanning electron microscope (SEM to understand the erosion mechanism.

  12. Matrix free fiber reinforced polymeric composites via high-temperature high-pressure sintering

    Science.gov (United States)

    Xu, Tao

    2004-11-01

    A novel manufacturing process called high-temperature high-pressure sintering was studied and explored. Solid fiber reinforced composites are produced by consolidating and compacting layers of polymeric fabrics near their melting temperature under high pressure. There is no need to use an additional matrix as a bonding material. Partial melting and recrystallization of the fibers effectively fuse the material together. The product is called a "matrix free" fiber reinforced composite and essentially a one-polymer composite in which the fiber and the matrix have the same chemical composition. Since the matrix is eliminated in the process, it is possible to achieve a high fiber volume fraction and light weight composite. Interfacial adhesion between fibers and matrix is very good due to the molecular continuity throughout the system and the material is thermally shapeable. Plain woven Spectra RTM cloth made of SpectraRTM fiber was used to comprehensively study the process. The intrinsic properties of the material demonstrate that matrix free SpectraRTM fiber reinforced composites have the potential to make ballistic shields such as body armor and helmets. The properties and structure of the original fiber and the cloth were carefully examined. Optimization of the processing conditions started with the probing of sintering temperatures by Differential Scanning Calorimetry. Coupled with the information from structural, morphological and mechanical investigations on the samples sintered at different processing conditions, the optimal processing windows were determined to ensure that the outstanding original properties of the fibers translate into high ballistic performance of the composites. Matrix free SpectraRTM composites exhibit excellent ballistic resistance in the V50 tests conducted by the US Army. In the research, process-structure-property relationship is established and correlations between various properties and structures are understood. Thorough knowledge is

  13. Electrical resistance stability of high content carbon fiber reinforced cement composite

    Institute of Scientific and Technical Information of China (English)

    YANG Zai-fu; TANG Zu-quan; LI Zhuo-qiu; QIAN Jue-shi

    2005-01-01

    The influences of curing time, the content of free evaporable water in cement paste, environmental temperature, and alternative heating and cooling on the electrical resistance of high content carbon fiber reinforced cement (CFRC) paste are studied by experiments with specimens of Portland cement 42.5 with 10 mm PAN-based carbon fiber and methylcellulose. Experimental results indicate that the electrical resistance of CFRC increases relatively by 24% within a hydration time of 90 d and almost keeps constant after 14 d, changes hardly with the mass loss of free evaporable water in the concrete dried at 50℃C, increases relatively by 4% when ambient temperature decreases from 15℃ to-20℃, and decreases relatively by 13% with temperature increasing by 88℃. It is suggested that the electric resistance of the CFRC is stable, which is testified by the stable power output obtained by electrifying the CFRC slab with a given voltage. This implies that such kind of high content carbon fiber reinforced cement composite is potentially a desirable electrothermal material for airfield runways and road surfaces deicing.

  14. Standard Guide for Identification of Fiber-Reinforced Polymer-Matrix Composite Materials in Databases

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2000-01-01

    1.1 This guide establishes essential and desirable data elements for fiber-reinforced composite materials for two purposes: to establish the material identification component of data-reporting requirements for test reporting and to provide information for the design of material property databases. 1.1.1 This guide is the first part of a two-part modular approach. The first part serves to identify the material and the second part serves to describe testing procedures and variables and to record results. 1.1.2 For mechanical testing, the related document is Guide E 1434. The interaction of this guide with Guide E 1434 is emphasized by the common numbering of data elements. Data Elements A1 through G13 are included in this guide, and numbering of data elements in Guide E 1434 begins with H1 for the next data element block. This guide is most commonly used in combination with a guide for reporting the test procedures and results such as Guide E 1434. 1.2 These guidelines are specific to fiber-reinforced polyme...

  15. Modeling of the mechanical behavior of fiber-reinforced ceramic composites using finite element method (FEM

    Directory of Open Access Journals (Sweden)

    Dimitrijević M.M.

    2014-01-01

    Full Text Available Modeling of the mechanical behavior of fiber-reinforced ceramic matrix composites (CMC is presented by the example of Al2O3 fibers in an alumina based matrix. The starting point of the modeling is a substructure (elementary cell which includes on a micromechanical scale the statistical properties of the fiber, matrix and fiber-matrix interface and their interactions. The numerical evaluation of the model is accomplished by means of the finite element method. The numerical results of calculating the elastic modulus of the composite dependance on the quantity of the fibers added and porosity was compared to experimental values of specimens having the same composition. [Projekat Ministarstva nauke Republike Srbije, br. ON174004 i TVH to project III45012

  16. Microstructure Effects of Ultrasonic Waves in a Fiber Reinforced Composite Plate

    Institute of Scientific and Technical Information of China (English)

    HAN Jun-Bo; TANG Li-Guo; CHENG Jian-Chun; Yves Berthelot

    2000-01-01

    The microstructure effect of ultrasonic waves in a unidirectional titanium graphite composite is analyzed by the mode energy conversions of the laser-generated ultrasonic Lamb wvaves. The carrying energy of each mode in the Lamb wvaves is calculated quantitatively by the time-frequency filtering technique of the Wigner distribution. We found that the energy conversions among modes have happened in the process of propagation of ultrasonic Lamb wave. These energy conversions are attributed to microstructure scattering of ultrasonic wave by the fibers in a fiber reinforced composite material. This work will provide a quantitative method of ultrasonic characterizationof microstructure feature of the composite materials by the laser-generated Lamb wave technique.

  17. Multi-response parametric optimization in drilling of bamboo/Kevlar fiber reinforced sandwich composite

    Science.gov (United States)

    Singh, Thingujam Jackson; Samanta, Sutanu

    2016-09-01

    In the present work an attempt was made towards parametric optimization of drilling bamboo/Kevlar K29 fiber reinforced sandwich composite to minimize the delamination occurred during the drilling process and also to maximize the tensile strength of the drilled composite. The spindle speed and the feed rate of the drilling operation are taken as the input parameters. The influence of these parameters on delamination and tensile strength of the drilled composite studied and analysed using Taguchi GRA and ANOVA technique. The results show that both the response parameters i.e. delamination and tensile strength are more influenced by feed rate than spindle speed. The percentage contribution of feed rate and spindle speed on response parameters are 13.88% and 81.74% respectively.

  18. Acoustic emission characterization of fracture toughness for fiber reinforced ceramic matrix composites

    Energy Technology Data Exchange (ETDEWEB)

    Mei, Hui, E-mail: phdhuimei@yahoo.com [Science and Technology on Thermostructure Composite Materials Laboratory, Northwestern Polytechnical University, Xi' an Shaanxi 710072 (China); Sun, Yuyao; Zhang, Lidong; Wang, Hongqin; Cheng, Laifei [Science and Technology on Thermostructure Composite Materials Laboratory, Northwestern Polytechnical University, Xi' an Shaanxi 710072 (China)

    2013-01-10

    The fracture toughness of a carbon fiber reinforced silicon carbide composite was investigated relating to classical critical stress intensity factor K{sub IC}, work of fracture, and acoustic emission energy. The K{sub IC} was obtained by the single edge notch beam method and the work of fracture was calculated using the featured area under the load-displacement curves. The K{sub IC}, work of fracture, and acoustic emission energy were compared for the composites before and after heat treatment and then analyzed associated with toughening microstructures of fiber pullout. It indicates that the work of fracture and acoustic emission energy can be more suitable to reflect the toughness rather than the traditional K{sub IC}, which has certain limitation for the fracture toughness characterization of the crack tolerant fiber ceramic composites.

  19. Nondestructive Evaluation of Carbon Fiber Reinforced Polymer Composites Using Reflective Terahertz Imaging

    Directory of Open Access Journals (Sweden)

    Jin Zhang

    2016-06-01

    Full Text Available Terahertz (THz time-domain spectroscopy (TDS imaging is considered a nondestructive evaluation method for composite materials used for examining various defects of carbon fiber reinforced polymer (CFRP composites and fire-retardant coatings in the reflective imaging modality. We demonstrate that hidden defects simulated by Teflon artificial inserts are imaged clearly in the perpendicular polarization mode. The THz TDS technique is also used to measure the thickness of thin fire-retardant coatings on CFRP composites with a typical accuracy of about 10 micrometers. In addition, coating debonding is successfully imaged based on the time-delay difference of the time-domain waveforms between closely adhered and debonded sample locations.

  20. Graphite Sheet Coating for Improved Thermal Oxidative Stability of Carbon Fiber Reinforced/PMR-15 Composites

    Science.gov (United States)

    Campbell, Sandi; Papadopoulos, Demetrios; Heimann, Paula; Inghram, Linda; McCorkle, Linda

    2005-01-01

    Expanded graphite was compressed into graphite sheets and used as a coating for carbon fiber reinforced PMR-15 composites. BET analysis of the graphite indicated an increase in graphite pore size on compression, however the material was proven to be an effective barrier to oxygen when prepegged with PMR-15 resin. Oxygen permeability of the PMR-15/graphite was an order of magnitude lower than the compressed graphite sheet. By providing a barrier to oxygen permeation, the rate of oxidative degradation of PMR-15 was decreased. As a result, the composite thermo-oxidative stability increased by up to 25%. The addition of a graphite sheet as a top ply on the composites yielded little change in the material's flexural strength or interlaminar shear strength.

  1. Production of natural fiber reinforced thermoplastic composites through the use of polyhydroxybutyrate-rich biomass.

    Science.gov (United States)

    Coats, Erik R; Loge, Frank J; Wolcott, Michael P; Englund, Karl; McDonald, Armando G

    2008-05-01

    Previous research has demonstrated that production of natural fiber reinforced thermoplastic composites (NFRTCs) utilizing bacterially-derived pure polyhydroxybutyrate (PHB) does not yield a product that is cost competitive with synthetic plastic-based NFRTCs. Moreover, the commercial production of pure PHB is not without environmental impacts. To address these issues, we integrated unpurified PHB in NFRTC construction, thereby eliminating a significant energy and cost sink (ca. 30-40%) while concurrently yielding a fully biologically based commodity. PHB-rich biomass synthesized with the microorganism Azotobacter vinelandii UWD was utilized to manufacture NFRTCs with wood flour. Resulting composites exhibited statistically similar bending strength properties despite relatively different PHB contents. Moreover, the presence of microbial cell debris allowed for NFRTC processing at significantly reduced polymer content, relative to pure PHB-based NFRTCs. Results further indicate that current commercial PHB production yields are sufficiently high to produce composites comparable to those manufactured with purified PHB.

  2. Crystallization behavior of three-dimensional silica fiber reinforced silicon nitride composite

    Science.gov (United States)

    Qi, Gongjin; Zhang, Changrui; Hu, Haifeng; Cao, Feng; Wang, Siqing; Jiang, Yonggang; Li, Bin

    2005-10-01

    The crystallization behavior of a new type of ceramic matrix composites, three-dimensional silica fiber reinforced silicon nitride matrix composite prepared by perhydropolysilazane infiltration and pyrolysis, was investigated by X-ray diffractometry and Fourier transform infrared spectroscopy. With the post-annealing treatment of the amorphous as-received composite at elevated tempertures of 1400 and 1600 °C in nitrogen atmosphere, there was remarkable suppression of the crystallization of polymer-derived silicon nitride ceramic matrix into α-Si 3N 4 and silica fibers into α-cristobalite, which was probably attributed to the phase of silicon oxynitrides originating from the strong fiber/matrix interfacial chemical reaction.

  3. The effect of joint surface contours and glass fiber reinforcement on the transverse strength of repaired acrylic resin: An in vitro study

    Directory of Open Access Journals (Sweden)

    Nayana Anasane

    2013-01-01

    Full Text Available Background : Denture fracture is an unresolved problem in complete denture prosthodontics. However, the repaired denture often experiences a refracture at the repaired site due to poor transverse strength. Hence, this study was conducted to evaluate the effect of joint surface contours and glass fiber reinforcement on the transverse strength of repaired acrylic resins. Materials and Methods: A total of 135 specimens of heat polymerized polymethyl methacrylate resin of dimensions 64 × 10 × 2.5 mm were fabricated. Fifteen intact specimens served as the control and 120 test specimens were divided into four groups (30 specimens each, depending upon the joint surface contour (butt, bevel, rabbet and round, with two subgroups based on type of the repair. Half of the specimens were repaired with plain repair resin and the other half with glass fibers reinforced repair resin. Transverse strength of the specimens was determined using three-point bending test. The results were analyzed using one-way ANOVA and Tukey post-hoc test (α= 0.05. Results: Transverse strength values for all repaired groups were significantly lower than those for the control group ( P < 0.001 (88.77 MPa, with exception of round surface design repaired with glass fiber reinforced repair resin (89.92 MPa which was significantly superior to the other joint surface contours ( P < 0.001. Glass fiber reinforced resin significantly improved the repaired denture base resins as compared to the plain repair resin ( P < 0.001. Conclusion: Specimens repaired with glass fiber reinforced resin and round surface design exhibited highest transverse strength; hence, it can be advocated for repair of denture base resins.

  4. Effects of Fiber-reinforced Composite Bases on Microleakage of Composite Restorations in Proximal Locations

    Science.gov (United States)

    A, Tezvergil-Mutluay; P.K, Vallittu

    2014-01-01

    Objectives: The aim of this study was to evaluate the microleakage of direct restorative composite resin upon the addition of an intermediate glass fiber-reinforced composite (GFRC) layer of various fiber orientations between tooth and particulate filler composite resin (PFRC). Materials and Methods: Cavities were prepared both on the mesial and distal surfaces of sixty extracted human molars with one margin placed below and the other above the cementoenamel junction (CEJ). Teeth were assigned to five different groups. Four of the groups received a layer of semi-interpenetrating polymer network (semi-IPN) resin system impregnated E-glass GFRC at the bottom of the cavity: Group 1; unidirectional continuous GFRC (EVS) in buccolingual direction (EVS-BL), Group 2; EVS in mesiodistal direction (EVS-MD), Group 3; bidirectional woven GFRC (EVN), Group 4; multidirectional short GFRC (EXP-MLT), Group 5; PRFC only (control). After acid etching and priming of the cavities and insertion of GFRC layer with the adhesive resin (Scotchbond Multipurpose 3M-ESPE), the cavities were filled incrementally with PRFC (Filtek Z250, 3M-ESPE) and each layer was light cured for 20 s. After finishing and polishing, the restored teeth were water-stored for 24 h at 37 °C and then thermocycled for 6000 cycles between 5-55 °C, before immersion in 0.5 % basic fuchsin dye for 24 h. After sectioning by 3-5 sagittal cuts, each sequential section was imaged and digitally analyzed to determine the stain depth. Results: All GFRC groups in dentin revealed significantly lower microleakage compared to control (p0.05). The microleakeage in enamel was not different between the groups (p>0.05). Conclusion: Use of intermediate GFRC layer between tooth and PFRC could provide alternative method to minimize microleakage. Clinical Relevance: Use of GFRC intermediate layer underneath the particulate filler composite can be used to minimize the leakeage of the restorations. PMID:25512764

  5. Effect of nanoparticle dispersion on mechanical behavior of polymer matrix and their fiber reinforced composites

    Science.gov (United States)

    Uddin, Mohammed Farid

    Fiber reinforced composites are widely used to achieve weight savings in different construction. However, their used are restricted as their matrix-dominant properties are much weaker than their fiber-dominated properties. The recent advent of nanoparticles has attracted much attention in improving the matrix properties by using various nanoparticles as reinforcements. Due to the lack of well-developed and consistent processing method, experimental results on nanocomposites show a broad spectrum of anomalies in their properties. Dispersion of nanoparticles in the polymeric precursor is often blamed for these inconsistencies in their properties which becomes even worse with high particle loading. In this research, a processing technique has been developed to fabricate very well-dispersed nanocomposite even with high particle loading in order to fully utilize the advantages of nanoparticle reinforcement. An attempt has also been made to modify the conventional sonication method to improve the dispersion by combining the sol-gel and sonication methods to fabricate hybrid nanocomposites. Transmission electronic microscopy has been employed to investigate dispersion quality of nanoparticles. Finally, mechanical characterization has been performed to evaluate the effect of different state of particle dispersion. Once the effect of dispersion is identified, a micromechanical model has been proposed to estimate the strength of particle reinforced composites based on particle/matrix interfacial crack growth. Finite element analyses were performed to validate the experimental results for microparticle reinforced composites. Using the model, effect of particle size has also been validated with experimental results. The model is then further extended to reveal the failure modes in nanocomposite with the support of some experimental evidences. Finally, an effort has been made to evaluate the potential application of the nanoparticle modified resin by fabricating unidirectional

  6. Fracture and Tensile Properties of Polyvinyl Alcohol Fiber Reinforced Cementitous Composites

    Institute of Scientific and Technical Information of China (English)

    XU Shilang; GAO Shuling

    2008-01-01

    Experiments were carried out to design polyvinyl alcohol(PVA)fiber reinforced cementitous composites(PVA-FRCCs)holding high ductility and energy consumption ability.Besides,the properties of each ingredients in composites,mixing method and technology for fresh mixture were described in detail.Then,the pseudo-strain-hardening(PSH)behavior was investigated in uniaxial tension test.As a result,them maximum ultimate tensile strain can reach 0.7 percent.On the other hand,the single edge notch(SEN)thin sheet specimens were employed to gain the normal tensile load via crack mouth opening displacement(CMOD)curves,which can show obvious PSH behavior.In addition,the curves can be divided into four zones whose fracture toughness calculation methods were discussed.The wedge splitting(WS)test method can be applied to discuss the fracture toughness.Moreover,fracture energy of SEN and WS specimens were both approximately evaluated.

  7. The importance of material structure in the laser cutting of glass fiber reinforced plastic composites

    Energy Technology Data Exchange (ETDEWEB)

    Caprino, G. (Univ. di Napoli (Italy). Dipt. di Ingegneria dei Materiali e della Produzione); Tagliaferri, V. (Univ. di Salerno (Italy). Istituto di Ingegneria Meccanica); Covelli, L. (IMU-Consiglio Nazionale delle Ricerche, Milano (Italy))

    1995-01-01

    A previously proposed micromechanical formula, aiming to predict the vaporization energy Q[sub v] of composite materials as a function of fiber and matrix properties and fiber volume ratio, was assessed. The experimental data, obtained on glass fiber reinforced plastic panels with different fiber contents cut by a medium power CO[sub 2] cw laser, were treated according to a procedure previously suggested, in order to evaluate Q[sub v]. An excellent agreement was found between experimental and theoretical Q[sub v] values. Theory was then used to predict the response to laser cutting of a composite material with a fiber content varying along the thickness. The theoretical predictions indicated that, in this case, the interpretation of the experimental results may be misleading, bringing to errors in the evaluation of the material thermal properties, or in the prediction of the kerf depth. Some experimental data were obtained, confirming the theoretical findings.

  8. Numerically design the injection process parameters of parts fabricated with ramie fiber reinforced green composites

    Science.gov (United States)

    Chen, L. P.; He, L. P.; Chen, D. C.; Lu, G.; Li, W. J.; Yuan, J. M.

    2017-01-01

    The warpage deformation plays an important role on the performance of automobile interior components fabricated with natural fiber reinforced composites. The present work investigated the influence of process parameters on the warpage behavior of A pillar trim made of ramie fiber (RF) reinforced polypropylene (PP) composites (RF/PP) via numerical simulation with orthogonal experiment method and range analysis. The results indicated that fiber addition and packing pressure were the most important factors affecting warpage. The A pillar trim can achieved the minimum warpage value as of 2.124 mm under the optimum parameters. The optimal process parameters are: 70% percent of the default value of injection pressure for the packing pressure, 20 wt% for the fiber addition, 185 °C for the melt °C for the mold temperature, 7 s for the filling time and 17 s for the packing time.

  9. Statistics of Microstructure, Peak Stress and Interface Damage in Fiber Reinforced Composites

    DEFF Research Database (Denmark)

    Kushch, Volodymyr I.; Shmegera, Sergii V.; Mishnaevsky, Leon

    2009-01-01

    This paper addresses an effect of the fiber arrangement and interactions on the peak interface stress statistics in a fiber reinforced composite material (FRC). The method we apply combines the multipole expansion technique with the representative unit cell model of composite bulk, which is able...... to simulate both the uniform and clustered random fiber arrangements. By averaging over a number of numerical tests, the empirical probability functions have been obtained for the nearest neighbor distance and the peak interface stress. It is shown that the considered statistical parameters are rather...... sensitive to the fiber arrangement, particularly cluster formation. An explicit correspondence between them has been established and an analytical formula linking the microstructure and peak stress statistics in FRCs has been suggested. Application of the statistical theory of extreme values to the local...

  10. Microstructure and phase stress partition of Mo fiber reinforced CuZnAl composite

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Feng [State Key Laboratory of Heavy Oil Processing, China University of Petroleum-Beijing, Beijing 102249 (China); Department of Materials Science and Engineering, China University of Petroleum-Beijing, Beijing 102249 (China); Ni, Dingrui [Shenyang National Laboratory for Materials Science, Institute of Metal Research, Chinese Academy of Sciences, 72 Wenhua Road, Shenyang 110016 (China); Hao, Shijie [State Key Laboratory of Heavy Oil Processing, China University of Petroleum-Beijing, Beijing 102249 (China); Department of Materials Science and Engineering, China University of Petroleum-Beijing, Beijing 102249 (China); Li, Sirui [Department of Materials Science and Engineering, China University of Petroleum-Beijing, Beijing 102249 (China); Ma, Zongyi [Shenyang National Laboratory for Materials Science, Institute of Metal Research, Chinese Academy of Sciences, 72 Wenhua Road, Shenyang 110016 (China); Liu, Yinong [School of Mechanical and Chemical Engineering, The University of Western Australia, Crawley, WA 6009 (Australia); Feng, Chun [Department of Materials Physics and Chemistry, University of Science and Technology Beijing, Beijing 100083 (China); Cui, Lishan, E-mail: andor_20@sina.com [State Key Laboratory of Heavy Oil Processing, China University of Petroleum-Beijing, Beijing 102249 (China); Department of Materials Science and Engineering, China University of Petroleum-Beijing, Beijing 102249 (China)

    2015-03-25

    A Mo fiber reinforced CuZnAl composite was prepared by means of friction stir processing and wire drawing. Reinforcing effect of the Mo fiber and phase stress partition in the composite were investigated by means of in-situ synchrotron X-ray diffraction. The maximum elastic strain of the Mo fiber achieved was 1.8%, implying a component stress of 550 MPa on the fibers. The Mo fibers, with a volume fraction of 10%, carried 80% of stress fraction during tensile deformation. The change of modulus caused by stress-induced martensitic transformation strain resulted in redistribution of the phase stress partition between Mo fibers and CuZnAl matrix.

  11. Reactive processing of textile-natural fiber reinforced anionic polyamide-6 composites

    Energy Technology Data Exchange (ETDEWEB)

    Kan, Ze; Chen, Peng; Liu, Zhengying; Feng, Jianmin; Yang, Mingbo [College of Polymer Science and Engineering, State Key Laboratory of Polymer Materials Engineering, Sichuan University, Chengdu 610065, Sichuan (China)

    2015-05-22

    Nowadays natural fiber, used in reinforced composites, is widely concerned. However, no natural fiber reinforced reactive thermoplastic polymer grades had been prepared so far. Through our studies, it was demonstrated that there was a severe retardation and discoloration occurred in the reactive processing between anionic polyamide-6 (APA-6) and natural fiber, which result in incomplete polymerization when put together. In order to solve the problem, two methods were adopted in this paper, which are fiber pretreatment and usage of a new-style initiator called caprolactam magnesium bromide. The former is to remove sizing agent and impurities on the surface of fiber, and the latter is to weaken the side reactions between APA-6 and natural fiber by the nature of its lower reactivity and weaker alkaline. In cooperation with both methods, the severe retardation and discoloration had been improved significantly, so that the polymerization of APA-6 in natural fiber was occurred smoothly. Following textile-natural fiber reinforced APA-6 composites with an average thickness of 2.5 mm and a fiber volume content of 50% was prepared by vacuum assisted resin transfer molding (VARTM). The soxhlet extraction, dilute solution viscometry and differential scanning calorimeter (DSC) measurements respectively suggested the degree of conversion, viscosity-average molar mass and crystallization of composites was up to 94%, 11.3×104 and 50%. Remarkable improvement of mechanical properties were achieved through dynamic mechanical analysis (DMA), tensile and three-point bending test. Favorable interfacial adhesion and wettability were revealed by scanning electron microscopy (SEM) observation. Therefore, all of the above good performance make this new-style and environmentally friendly composites have broad application prospects.

  12. Effects of Interface Modification on Mechanical Behavior of Hi-Nicalon Fiber-Reinforced Celsian Matrix Composites

    Science.gov (United States)

    Bansal, Narottam P.; Eldridge, Jeffrey I.

    1997-01-01

    Unidirectional celsian matrix composites having approx. 42 volume percent of uncoated or BN/SiC-coated Hi-Nicalon fibers were tested in three-point bend at room temperature. The uncoated fiber-reinforced composites showed catastrophic failure with strength of 210 +/- 35 MPa and a flat fracture surface. In contrast, composites reinforced with BN/SiC-coated fibers exhibited graceful failure with extensive fiber pullout. Values of first matrix cracking stress and strain were 435 +/- 35 MPa and 0.27 +/- 0.01 %, respectively, with ultimate strength as high as 960 MPa. The elastic Young's modulus of the uncoated and BN/SiC-coated fiber-reinforced composites were measured as 184 q 4 GPa and 165 +/- 5 GPa, respectively. Fiber push-through tests and microscopic examination indicated no chemical reaction at the uncoated or coated fiber-matrix interface. The low strength of the uncoated fiber-reinforced composite is probably due to degradation of the fibers from mechanical surface damage during processing. Because both the coated and uncoated fiber reinforced composites exhibited weak interfaces, the beneficial effect of the BN-SiC dual layer is primarily the protection of fibers from mechanical damage during processing.

  13. Fiber-reinforced composites as a fixed space maintainer in case of primary tooth loss.

    Science.gov (United States)

    Acharya, Sonu; Tandon, Shobha

    2011-01-01

    Restorative dentistry is continually changing, with ground-breaking treatments developing based on new materials, techniques, and technologies. Composite materials are a leading example, and the introduction of fiber reinforcement has further increased the possible uses of composites in restorative dentistry. Maintaining arch length during primary, mixed, and early permanent dentition is essential for the development of occlusion. In an effort to prevent future problems, appliances may be placed to retain space resulting from early loss of teeth. In case of primary teeth loss, fixed space maintainers are being used, but these are time consuming to fabricate, and incorporated wires may lead to soft tissue trauma. This clinical case uses fiber-reinforced composite as a space maintainer, thus reducing the time required to complete treatment. In spite of best efforts of practicing dentists, there still remains a large percentage of the population who do not present for treatment, except with pain or other condition. Unfortunately some of those individuals are children, who are not in a position to make the difficult decision to visit the dentist independently. Often by the time they are examined, there is no chance of saving the involved tooth, necessitating extraction and space maintenance. To prevent closure of space and arch length deficiency, appliances may be placed to retain space. Different appliances may be used for space maintenance, such as the removable and fixed space maintainers, but they are difficult and time consuming to construct. Also, the attention span of a child patient is insufficient for this treatment protocol. Considering these difficulties, the clinician could choose the option of a space maintainer, which is less time consuming to fabricate, and for which patient acceptance is optimal.

  14. Crystallization kinetics and thermal resistance of bamboo fiber reinforced biodegradable polymer composites

    Science.gov (United States)

    Thumsorn, S.; Srisawat, N.; On, J. Wong; Pivsa-Art, S.; Hamada, H.

    2014-05-01

    Bamboo fiber reinforced biodegradable polymer composites were prepared in this study. Biodegradable poly(butylene succinate) (PBS) was blended with bamboo fiber in a twin screw extruder with varied bamboo content from 20-0wt%. PBS/bamboo fiber composites were fabricated by compression molding process. The effect of bamboo fiber contents on properties of the composites was investigated. Non-isothermal crystallization kinetic study of the composites was investigated based on Avrami equation. The kinetic parameters indicated that bamboo fiber acted as heterogeneous nucleation and enhanced crystallinity of the composites. Bamboo fiber was well dispersed on PBS matrix and good adhered with the matrix. Tensile strength of the composites slightly deceased with adding bamboo fiber. However, tensile modulus and impact strength of the composites increased when increasing bamboo fiber contents. It can be noted that bamboo fiber promoted crystallization and crystallinity of PBS in the composites. Therefore, the composites were better in impact load transferring than neat PBS, which exhibited improving on impact performance of the composites.

  15. Interfacial Shear Strength Measurements of SiC Fiber-Reinforced Titanium Composites

    Institute of Scientific and Technical Information of China (English)

    Yanhua LI; Nanlin SHI; Dezhi ZHANG; Rui YANG

    2005-01-01

    A continuous loading push-out test technique was used to measure the interfacial shear strength of SiC fiber reinforced Ti matrix composites. The interracial shear strength of samples as-fabricated and after heat exposed at 700 and 800℃ for 50 h was successfully determined. It has been found that the interfacial shear strength of the specimen exposed at 700℃ was higher than that of as-prepared and exposed samples at 800℃. The shear strength of the as-prepared samples was about 112.45 MPa, and increased to about 153.77 MPa after heat-treating at 700℃ for 50 h, but decreased to 133.11 MPa after treating at 800℃ for 50 h. Scanning electron microscope (SEM) was used to investigate the interfacial morphology of the samples. The brittle phase was the main products of interface for samples exposed at 800℃, and the interface was easily peeled off.

  16. Segmenting delaminations in carbon fiber reinforced polymer composite CT using convolutional neural networks

    Science.gov (United States)

    Sammons, Daniel; Winfree, William P.; Burke, Eric; Ji, Shuiwang

    2016-02-01

    Nondestructive evaluation (NDE) utilizes a variety of techniques to inspect various materials for defects without causing changes to the material. X-ray computed tomography (CT) produces large volumes of three dimensional image data. Using the task of identifying delaminations in carbon fiber reinforced polymer (CFRP) composite CT, this work shows that it is possible to automate the analysis of these large volumes of CT data using a machine learning model known as a convolutional neural network (CNN). Further, tests on simulated data sets show that with a robust set of experimental data, it may be possible to go beyond just identification and instead accurately characterize the size and shape of the delaminations with CNNs.

  17. Electrical Resistance and Microstructure of Latex Modified Carbon Fiber Reinforced Cement Composites

    Institute of Scientific and Technical Information of China (English)

    WEI Jian; CHENG Feng; YUAN Hudie

    2012-01-01

    The electrical resistance,flexural strength,and microstructure of carbon fiber reinforced cement composites (CFRC) were improved greatly by adding water-redispersible latex powder.The electrical resistance of CFRC was investigated by two-probe method.The input range of CFRC based strain sensors was therefore increased,whereas electrical resistance was increased and remained in the perfect range of CFRC sensors.The analysis of scanning electron microscopy indicated that elastic latex bridges and a latex layer existed among the interspaces of the adjacent cement hydration products which were responsible for the enhancement of the flexural strength and electrical resistance.The formation mechanism of the elastic latex bridges was also discussed in detail.The continuous moving of two opposite interfaces of the latex solution-air along the interspaces of the adjacent hydrated crystals or colloids was attributed to the formation of the elastic latex bridges.

  18. Glass fiber-reinforced composite resin as a space maintainer: A clinical study

    Directory of Open Access Journals (Sweden)

    Subramaniam P

    2008-12-01

    Full Text Available The aim of this study is to evaluate the use of glass fiber-reinforced composite resin (GFRCR as a space maintainer and to compare it with a conventional band-and-loop space maintainer. A total of 30 children (23 boys and 7 girls aged 6-8 years were selected for the study. Each of these children required maintenance of space due to premature loss of primary first molars in at least two quadrants. In one quadrant, a GFRCR space maintainer was applied and in the other quadrant a band-and-loop space maintainer was cemented. Patients were recalled at regular intervals over 12 months and retention of both the types of space maintainers was evaluated. The retention of the GFRCR space maintainer was found to be superior to that of the band-and-loop space maintainer, but this difference was not statistically significant.

  19. Glass fiber-reinforced composite resin as a space maintainer: a clinical study.

    Science.gov (United States)

    Subramaniam, P; Babu, Gkl; Sunny, R

    2008-01-01

    The aim of this study is to evaluate the use of glass fiber-reinforced composite resin (GFRCR) as a space maintainer and to compare it with a conventional band-and-loop space maintainer. A total of 30 children (23 boys and 7 girls) aged 6-8 years were selected for the study. Each of these children required maintenance of space due to premature loss of primary first molars in at least two quadrants. In one quadrant, a GFRCR space maintainer was applied and in the other quadrant a band-and-loop space maintainer was cemented. Patients were recalled at regular intervals over 12 months and retention of both the types of space maintainers was evaluated. The retention of the GFRCR space maintainer was found to be superior to that of the band-and-loop space maintainer, but this difference was not statistically significant.

  20. Simulation of a Novel Joining Process for Fiber-Reinforced Thermoplastic Composites and Metallic Components

    Science.gov (United States)

    Gude, M.; Freund, A.; Vogel, C.; Kupfer, R.

    2017-01-01

    In this study, a new joining technology to produce hybrid structures with continuous-fiber-reinforced thermoplastics and metallic components is presented adapting the concept of classical clinching for thermoplastic composites. To demonstrate the capability of the thermoclinching process, prototypic joints were manufactured using an experimental joining installation developed. Nondestructive and destructive analyses of the thermoclinched joints showed that a relocation of the reinforcement into the neck and head area of the joining zone could be achieved. For a first estimation of the maximum load-carrying capacity of the joints, single-lap specimens with both reinforced and nonreinforced thermoplastics were manufactured and tested, revealing up to 50% higher failure loads of the reinforced joints. To understand the local material configuration and to achieve a defined and adjustable fabric structure in the head area of the joint, further analyses with regard to material- and tool-side conditions of the joining zone are necessary.

  1. INFLUENCE OF LOADING RATE ON DYNAMIC FRACTURE BEHAVIOR OF FIBER-REINFORCED COMPOSITES

    Institute of Scientific and Technical Information of China (English)

    Kezhuang Gong; Zheng Li; Weizhong Qin

    2008-01-01

    The effect of loading rate on the dynamic fracture properties and the failure mechanisms of glass fiber-reinforced composite materials under mode I fracture is studied.Dynamic reflective caustic experiments are carried out for two loading rates.By measuring the characteristic dimensions of the shadow spots during the caustic experiments,the dynamic SIFs are calculated for different loading rates.The experimental results indicate that the dynamic fracture toughness KId increases remarkably with increasing loading rate,and the crack grows faster under the high-velocity impact.Moreover,by examining the crack growth routes and the fracture surfaces,it is shown that the loading rate also greatly affects the failure mechanisms at micro-scale.

  2. Electrical impedance spectroscopy for measuring the impedance response of carbon-fiber-reinforced polymer composite laminates

    KAUST Repository

    Almuhammadi, Khaled

    2017-02-16

    Techniques that monitor the change in the electrical properties of materials are promising for both non-destructive testing and structural health monitoring of carbon-fiber-reinforced polymers (CFRPs). However, achieving reliable monitoring using these techniques requires an in-depth understanding of the impedance response of these materials when subjected to an alternating electrical excitation, information that is only partially available in the literature. In this work, we investigate the electrical impedance spectroscopy response at various frequencies of laminates chosen to be representative of classical layups employed in composite structures. We clarify the relationship between the frequency of the electrical current, the conductivity of the surface ply and the probing depth for different CFRP configurations for more efficient electrical signal-based inspections. We also investigate the effect of the amplitude of the input signal.

  3. Fracture behavior of structurally compromised non-vital maxillary premolars restored using experimental fiber reinforced composite crowns.

    NARCIS (Netherlands)

    Fokkinga, W.A.; Kreulen, C.M.; Bell-Ronnlof, A.M. Le; Lassila, L.V.; Vallittu, P.K.; Creugers, N.H.J.

    2006-01-01

    PURPOSE: To study the fracture behavior of direct resin composite crowns with or without experimental fiber reinforcement. METHODS: Clinical crowns of single-rooted maxillary premolars were cut off at the cemento-enamel junction. Canals were prepared with Gates Glidden drills up to size 4. No additi

  4. Fracture strength and bending of all-ceramic and fiber-reinforced composites in inlay-retained fixed partial dentures

    Directory of Open Access Journals (Sweden)

    Serkan Saridag

    2012-06-01

    Conclusions: Zirconia-based ceramic inlay-retained fixed partial dentures demonstrated the highest fracture strength. The fiber-reinforced composite inlay-retained fixed partial dentures demonstrated higher bending values than did the all-ceramic inlay-retained fixed partial dentures.

  5. Five-year survival of 3-unit fiber-reinforced composite fixed partial dentures in the posterior area.

    NARCIS (Netherlands)

    Heumen, C.C.M. van; Tanner, J.; Dijken, J.W.V. van; Pikaar, R.; Lassila, L.V.; Creugers, N.H.J.; Vallittu, P.K.; Kreulen, C.M.

    2010-01-01

    OBJECTIVES: The purpose of this clinical study was to evaluate the long-term outcome of three-unit posterior fixed partial dentures (FPDs) made of fiber-reinforced resin composite (FRC), and to identify design factors influencing the survival rate. METHODS: 77 patients (52 females, 25 males) receive

  6. Titanium Implant Osseointegration Problems with Alternate Solutions Using Epoxy/Carbon-Fiber-Reinforced Composite.

    Science.gov (United States)

    Petersen, Richard C

    2014-12-01

    The aim of the article is to present recent developments in material research with bisphenyl-polymer/carbon-fiber-reinforced composite that have produced highly influential results toward improving upon current titanium bone implant clinical osseointegration success. Titanium is now the standard intra-oral tooth root/bone implant material with biocompatible interface relationships that confer potential osseointegration. Titanium produces a TiO2 oxide surface layer reactively that can provide chemical bonding through various electron interactions as a possible explanation for biocompatibility. Nevertheless, titanium alloy implants produce corrosion particles and fail by mechanisms generally related to surface interaction on bone to promote an inflammation with fibrous aseptic loosening or infection that can require implant removal. Further, lowered oxygen concentrations from poor vasculature at a foreign metal surface interface promote a build-up of host-cell-related electrons as free radicals and proton acid that can encourage infection and inflammation to greatly influence implant failure. To provide improved osseointegration many different coating processes and alternate polymer matrix composite (PMC) solutions have been considered that supply new designing potential to possibly overcome problems with titanium bone implants. Now for important consideration, PMCs have decisive biofunctional fabrication possibilities while maintaining mechanical properties from addition of high-strengthening varied fiber-reinforcement and complex fillers/additives to include hydroxyapatite or antimicrobial incorporation through thermoset polymers that cure at low temperatures. Topics/issues reviewed in this manuscript include titanium corrosion, implant infection, coatings and the new epoxy/carbon-fiber implant results discussing osseointegration with biocompatibility related to nonpolar molecular attractions with secondary bonding, carbon fiber in vivo properties, electrical

  7. Titanium Implant Osseointegration Problems with Alternate Solutions Using Epoxy/Carbon-Fiber-Reinforced Composite

    Directory of Open Access Journals (Sweden)

    Richard C. Petersen

    2014-12-01

    Full Text Available The aim of the article is to present recent developments in material research with bisphenyl-polymer/carbon-fiber-reinforced composite that have produced highly influential results toward improving upon current titanium bone implant clinical osseointegration success. Titanium is now the standard intra-oral tooth root/bone implant material with biocompatible interface relationships that confer potential osseointegration. Titanium produces a TiO2 oxide surface layer reactively that can provide chemical bonding through various electron interactions as a possible explanation for biocompatibility. Nevertheless, titanium alloy implants produce corrosion particles and fail by mechanisms generally related to surface interaction on bone to promote an inflammation with fibrous aseptic loosening or infection that can require implant removal. Further, lowered oxygen concentrations from poor vasculature at a foreign metal surface interface promote a build-up of host-cell-related electrons as free radicals and proton acid that can encourage infection and inflammation to greatly influence implant failure. To provide improved osseointegration many different coating processes and alternate polymer matrix composite (PMC solutions have been considered that supply new designing potential to possibly overcome problems with titanium bone implants. Now for important consideration, PMCs have decisive biofunctional fabrication possibilities while maintaining mechanical properties from addition of high-strengthening varied fiber-reinforcement and complex fillers/additives to include hydroxyapatite or antimicrobial incorporation through thermoset polymers that cure at low temperatures. Topics/issues reviewed in this manuscript include titanium corrosion, implant infection, coatings and the new epoxy/carbon-fiber implant results discussing osseointegration with biocompatibility related to nonpolar molecular attractions with secondary bonding, carbon fiber in vivo

  8. Shear Bond Strength between Fiber-Reinforced Composite and Veneering Resin Composites with Various Adhesive Resin Systems.

    Science.gov (United States)

    AlJehani, Yousef A; Baskaradoss, Jagan K; Geevarghese, Amrita; AlShehry, Marey A; Vallittu, Pekka K

    2016-07-01

    The aim of this research was to evaluate the shear bond strength of different laboratory resin composites bonded to a fiber-reinforced composite substrate with some intermediate adhesive resins. Mounted test specimens of a bidirectional continuous fiber-reinforced substrate (StickNet) were randomly assigned to three equal groups. Three types of commercially available veneering resin composites - BelleGlass®, Sinfony®, and GC Gradia® were bonded to these specimens using four different adhesive resins. Half the specimens per group were stored for 24 hours; the remaining were stored for 30 days. There were 10 specimens in the test group (n). The shear bond strengths were calculated and expressed in MPa. Data were analyzed statistically, and variations in bond strength within each group were additionally evaluated by calculating the Weibull modulus. Shear bond values of those composites are influenced by the different bonding resins and different indirect composites. There was a significant difference in the shear bond strengths using different types of adhesive resins (p = 0.02) and using different veneering composites (p composite resin exhibited the lowest shear bond strength values when used with the same adhesive resins. The adhesive mode of failure was higher than cohesive with all laboratory composite resins bonded to the StickNet substructure at both storage times. Water storage had a tendency to lower the bond strengths of all laboratory composites, although the statistical differences were not significant. Within the limitations of this study, it was found that bonding of the veneering composite to bidirectional continuous fiber-reinforced substrate is influenced by the brand of the adhesive resin and veneering composite. © 2015 by the American College of Prosthodontists.

  9. Curaua fiber reinforced high-density polyethylene composites: effect of impact modifier and fiber loading

    Directory of Open Access Journals (Sweden)

    Jaqueline Albano de Morais

    2016-01-01

    Full Text Available Abstract Short fibers are used in thermoplastic composites to increase their tensile and flexural resistance; however, it often decreases impact resistance. Composites with short vegetal fibers are not an exception to this behavior. The purpose of this work is to produce a vegetal fiber reinforced composite with improved tensile and impact resistance in relation to the polymer matrix. We used poly(ethylene-co-vinyl acetate, EVA, to recover the impact resistance of high density polyethylene, HDPE, reinforced with Curauá fibers, CF. Blends and composites were processed in a corotating twin screw extruder. The pure polymers, blends and composites were characterized by differential scanning calorimetry, thermogravimetry, infrared spectroscopy, scanning electron microscopy, tensile mechanical properties and Izod impact resistance. EVA used as impact modifier in the HDPE matrix exhibited a co-continuous phase and in the composites the fibers were homogeneously dispersed. The best combination of mechanical properties, tensile, flexural and impact, were obtained for the formulations of composites with 20 wt. % of CF and 20 to 40 wt. % of EVA. The composite prepared with 20 wt. % EVA and containing 30 wt. % of CF showed impact resistance comparable to pure HDPE and improved tensile and flexural mechanical properties.

  10. Wear and transfer characteristics of carbon fiber reinforced polymer composites under water lubrication

    Institute of Scientific and Technical Information of China (English)

    JIA Jun-hong; CHEN Jian-min; ZHOU Hui-di; CHEN Lei

    2004-01-01

    The tribological characteristics of carbon fiber reinforced polymer composites under distilled-water-lubricated-sliding and dry-sliding against stainless steel were comparatively investigated. Scanning electron microscopy (SEM) was utilized to examine composite microstructures and modes of failure. The typical chemical states of elements of the transfer film on the stainless steel were examined with X-ray photoelectron spectroscopy (XPS). Wear testing and SEM analysis show that all the composites hold the lowered friction coefficient and show much better wear resistance under water lubricated sliding against stainless steel than those under dry sliding. The wear of composites is characterized by plastic deformation, scuffing, micro cracking, and spalling under both dry-sliding and water lubricated conditions. Plastic deformation, scuffing, micro cracking, and spalling, however, are significantly abated under water-lubricated condition. XPS analysis conforms that none of the materials produces transfer films on the stainless steel counterface with the type familiar from dry sliding, and the transfer of composites onto the counterpart ring surface is significantly hindered while the oxidation of the stainless steel is speeded under water lubrication. The composites hinder transfer onto the steel surface and the boundary lubricating action of water accounts for the much smaller wear rate under water lubrication compared with that under dry sliding. The easier transfer of the composite onto the counterpart steel surface accounts for the larger wear rate of the polymer composite under dry sliding.

  11. Curaua fiber reinforced high-density polyethylene composites: effect of impact modifier and fiber loading

    Directory of Open Access Journals (Sweden)

    Jaqueline Albano de Morais

    Full Text Available Abstract Short fibers are used in thermoplastic composites to increase their tensile and flexural resistance; however, it often decreases impact resistance. Composites with short vegetal fibers are not an exception to this behavior. The purpose of this work is to produce a vegetal fiber reinforced composite with improved tensile and impact resistance in relation to the polymer matrix. We used poly(ethylene-co-vinyl acetate, EVA, to recover the impact resistance of high density polyethylene, HDPE, reinforced with Curauá fibers, CF. Blends and composites were processed in a corotating twin screw extruder. The pure polymers, blends and composites were characterized by differential scanning calorimetry, thermogravimetry, infrared spectroscopy, scanning electron microscopy, tensile mechanical properties and Izod impact resistance. EVA used as impact modifier in the HDPE matrix exhibited a co-continuous phase and in the composites the fibers were homogeneously dispersed. The best combination of mechanical properties, tensile, flexural and impact, were obtained for the formulations of composites with 20 wt. % of CF and 20 to 40 wt. % of EVA. The composite prepared with 20 wt. % EVA and containing 30 wt. % of CF showed impact resistance comparable to pure HDPE and improved tensile and flexural mechanical properties.

  12. Spectroscopic study of terahertz reflection and transmission properties of carbon-fiber-reinforced plastic composites

    Science.gov (United States)

    Zhang, Jin; Shi, Changcheng; Ma, Yuting; Han, Xiaohui; Li, Wei; Chang, Tianying; Wei, Dongshan; Du, Chunlei; Cui, Hong-Liang

    2015-05-01

    Carbon-fiber-reinforced plastic (CFRP) composites are widely used in aerospace and concrete structure reinforcement due to their high strength and light weight. Terahertz (THz) time-domain spectroscopy is an attractive tool for defect inspection in CFRP composites. In order to improve THz nondestructive testing of CFRP composites, we have carried out systematic investigations of THz reflection and transmission properties of CFRP. Unidirectional CFRP composites with different thicknesses are measured with polarization directions 0 deg to 90 deg with respect to the fiber direction, in both reflection and transmission modes. As shown in the experiments, CFRP composites are electrically conducting and therefore exhibit a high THz reflectivity. In addition, CFRP composites have polarization-dependent reflectivity and transmissivity for THz radiation. The reflected THz power in the case of parallel polarization is nearly 1.8 times higher than for perpendicular polarization. At the same time, in the transmission of THz wave, a CFRP acts as a Fabry-Pérot cavity resulting from multiple internal reflections from the CFRP-air interfaces. Moreover, from the measured data, we extract the refractive index and absorption coefficient of CFRP composites in the THz frequency range.

  13. Vibration and Damping Analysis of Composite Fiber Reinforced Wind Blade with Viscoelastic Damping Control

    Directory of Open Access Journals (Sweden)

    Tai-Hong Cheng

    2015-01-01

    Full Text Available Composite materials are increasingly used in wind blade because of their superior mechanical properties such as high strength-to-weight and stiffness-to-weight ratio. This paper presents vibration and damping analysis of fiberreinforced composite wind turbine blade with viscoelastic damping treatment. The finite element method based on full layerwise displacement theory was employed to analyze the damping, natural frequency, and modal loss factor of composite shell structure. The lamination angle was considered in mathematical modeling. The curved geometry, transverse shear, and normal strains were exactly considered in present layerwise shell model, which can depict the zig-zag in-plane and out-of-plane displacements. The frequency response functions of curved composite shell structure and wind blade were calculated. The results show that the damping ratio of viscoelastic layer is found to be very sensitive to determination of magnitude of composite structures. The frequency response functions with variety of thickness of damping layer were investigated. Moreover, the natural frequency, modal loss factor, and mode shapes of composite fiber reinforced wind blade with viscoelastic damping control were calculated.

  14. Three-dimensional finite element analysis of posterior fiber-reinforced composite fixed partial denture Part 2: influence of fiber reinforcement on mesial and distal connectors.

    Science.gov (United States)

    Aida, Nobuhisa; Shinya, Akikazu; Yokoyama, Daiichiro; Lassila, Lippo V J; Gomi, Harunori; Vallittu, Pekka K; Shinya, Akiyoshi

    2011-01-01

    The aim of this study was to evaluate the influence of connectors under two different loading conditions on displacement and stress distribution generated in isotropic hybrid composite fixed partial denture (C-FPD) and partially anisotropic fiber-reinforced hybrid composite fixed partial denture (FRC-FPD). To this end, two three-dimensional finite element (FE) models of three-unit FPD from mandibular second premolar to mandibular second molar - intended to replace the mandibular first molar - were developed. The two loading conditions employed were a vertical load of 629 N (applied to eight points on the occlusal surface) and a lateral load of 250 N (applied to three points of the pontic). The results suggested that the reinforcing fibers in FRC framework significantly improved the rigidity of the connectors against any twisting and bending moments induced by loading. Consequently, maximum principal stress and displacement generated in the connectors of FRC-FPD were significantly reduced because stresses generated by vertical and lateral loading were transferred to the reinforcing fibers.

  15. A comprehensive study of woven carbon fiber-reinforced nylon 6 composites

    Science.gov (United States)

    Pillay, Selvum

    Liquid molding of thermoset composites has become very popular in all industry sectors, including aerospace, automotive, mass transit, and sporting goods, but the cost of materials and processing has limited the use to high-end applications. Thermoplastic composites are relatively cheap; however, the use has been limited to components with short fiber reinforcing. The high melt viscosity and short processing window precludes their use in the liquid molding of large structures and applications with continuous fiber reinforcement. The current research addresses the processing parameters, methodology, and limitations of vacuum assisted resin transfer molding (VARTM) of carbon fabric-reinforced, thermoplastic polyamide 6 (PA6). The material used is casting grade PA6. The process developed for using VARTM to produce carbon fabric-reinforced PA6 composites is explained in detail. The effects of infusion temperature and flow distance on the fiber weight fraction and crystallinity of the PA6 resin are presented. The degree of conversion from monomer to polymer was determined. Microscopic studies to show the wet-out of the fibers at the filament level are also presented. Tensile, flexural, short beam shear strength (SBSS), and low-velocity impact test results are presented and compared to a equivalent thermoset matrix composite. The rubber toughened epoxy system (SC-15) was chosen for the comparative study because the system has been especially developed to overcome the brittle nature of epoxy composites. The environmental effects of moisture and ultraviolet (UV) radiation on the carbon/nylon 6 composite were investigated. The samples were immersed in boiling water for 100 hr, and mechanical tests were conducted. Results showed that moisture causes plasticization of the matrix and attacks the fiber matrix interface. This leads to deterioration of the mechanical properties. The samples were also exposed to UV for up to 600 hr, and post exposure tests were conducted. The

  16. Processing and Material Characterization of Continuous Basalt Fiber Reinforced Ceramic Matrix Composites Using Polymer Derived Ceramics.

    Science.gov (United States)

    Cox, Sarah B.

    2014-01-01

    The need for high performance vehicles in the aerospace industry requires materials which can withstand high loads and high temperatures. New developments in launch pads and infrastructure must also be made to handle this intense environment with lightweight, reusable, structural materials. By using more functional materials, better performance can be seen in the launch environment, and launch vehicle designs which have not been previously used can be considered. The development of high temperature structural composite materials has been very limited due to the high cost of the materials and the processing needed. Polymer matrix composites can be used for temperatures up to 260C. Ceramics can take much higher temperatures, but they are difficult to produce and form in bulk volumes. Polymer Derived Ceramics (PDCs) begin as a polymer matrix, allowing a shape to be formed and cured and then to be pyrolized in order to obtain a ceramic with the associated thermal and mechanical properties. The use of basalt in structural and high temperature applications has been under development for over 50 years, yet there has been little published research on the incorporation of basalt fibers as a reinforcement in the composites. In this study, continuous basalt fiber reinforced PDCs have been fabricated and tested for the applicability of this composite system as a high temperature structural composite material. The oxyacetylene torch testing and three point bend testing have been performed on test panels and the test results are presented.

  17. Optimization and Static Stress Analysis of Hybrid Fiber Reinforced Composite Leaf Spring

    Directory of Open Access Journals (Sweden)

    Luay Muhammed Ali Ismaeel

    2015-01-01

    Full Text Available A monofiber reinforced composite leaf spring is proposed as an alternative to the typical steel one as it is characterized by high strength-to-weight ratio. Different reinforcing schemes are suggested to fabricate the leaf spring. The composite and the typical steel leaf springs are subjected to the same working conditions. A weight saving of about more than 60% can be achieved while maintaining the strength for the structures under consideration. The objective of the present study was to replace material for leaf spring. This study suggests various materials of hybrid fiber reinforced plastics (HFRP. Also the effects of shear moduli of the fibers, matrices, and the composites on the composites performance and responses are discussed. The results and behaviors of each are compared with each other and verified by comparison with analytical solution; a good convergence is found between them. The elastic properties of the hybrid composites are calculated using rules of mixtures and Halpin-Tsi equation through the software of MATLAB v-7. The problem is also analyzed by the technique of finite element analysis (FEA through the software of ANSYS v-14. An element modeling was done for every leaf with eight-node 3D brick element (SOLID185 3D 8-Node Structural Solid.

  18. Carbon nanotube-based structural health monitoring for fiber reinforced composite materials

    Science.gov (United States)

    Liu, Hao; Liu, Kan; Mardirossian, Aris; Heider, Dirk; Thostenson, Erik

    2017-04-01

    In fiber reinforced composite materials, the modes of damage accumulation, ranging from microlevel to macro-level (matrix cracks development, fiber breakage, fiber-matrix de-bonding, delamination, etc.), are complex and hard to be detected through conventional non-destructive evaluation methods. Therefore, in order to assure the outstanding structural performance and high durability of the composites, there has been an urgent need for the design and fabrication smart composites with self-damage sensing capabilities. In recent years, the macroscopic forms of carbon nanotube materials have been maturely investigated, which provides the opportunity for structural health monitoring based on the carbon nanotubes that are integrated in the inter-laminar areas of advanced fiber composites. Here in this research, advanced fiber composites embedded with laminated carbon nanotube layers are manufactured for damage detection due to the relevant spatial electrical property changes once damage occurs. The mechanical-electrical coupling response is recorded and analyzed during impact test. The design and manufacturing of integrating the carbon nanotubes intensely affect the detecting sensitivity and repeatability of the integrated multifunctional sensors. The ultimate goal of the reported work is to develop a novel structural health monitoring method with the capability of reporting information on the damage state in a real-time way.

  19. Macroscopic Mechanical Characterization of SMAs Fiber-Reinforced Hybrid Composite Under Uniaxial Loading

    Science.gov (United States)

    Lei, Hongshuai; Wang, Zhenqing; Tong, Liyong; Tang, Xiaojun

    2013-10-01

    This paper presents an experimental and theoretical investigation on the macroscopic mechanical behavior of shape memory alloys (SMAs) fiber-reinforced glass/resin composite subject to uniaxial loading at ambient temperature. A series of unidirectional SMAs reinforced composite laminates is fabricated through vacuum-assisted resin injection. Scanning electron microscopy is conducted to evaluate the interfacial cohesive quality between SMAs fiber and matrix. A theoretical model is proposed based on the SMAs phase transformation model and rule of mixture. Uniaxial tensile tests are performed to study the effects of weak interface and SMAs fiber volume fraction on the effective modulus of composite. Failure morphology of composite is discussed based on the observation using digital HF microscope. Due to the effects of phase transformation and weak interface, the overall stiffness of SMAs composite at the second stage is on average 10% lower than theoretical results. The rupture elongation of experimental result is approximately 13% higher than theoretical result. The local interfacial debonding between SMAs fiber and glass/resin matrix is the main failure mode.

  20. Au ion irradiation of various silicon carbide fiber-reinforced SiC matrix composites

    Energy Technology Data Exchange (ETDEWEB)

    Chaâbane, Nihed, E-mail: nihed.chaabane@cea.fr [CEA, INSTN/UEPTN, F-91191 Gif-sur-Yvette (France); Flem, Marion Le [CEA, DEN/DMN/SRMA, F-91191 Gif-sur-Yvette (France); Tanguy, Morgane [CEA, INSTN/UEPTN, F-91191 Gif-sur-Yvette (France); Urvoy, Stéphane [CEA, DEN/DMN/SRMA, F-91191 Gif-sur-Yvette (France); Sandt, Christophe; Dumas, Paul [Synchrotron SOLEIL, L’Orme des Merisiers, Saint-Aubin, BP 48, 91192 Gif-sur-Yvette Cedex (France); Serruys, Yves [CEA, DEN/DMN/SRMP, Laboratoire JANNUS, F-91191 Gif-sur-Yvette (France)

    2013-08-15

    Silicon carbide fiber-reinforced SiC matrix composites are promising candidates as fuel cladding for several concepts of Generation IV reactors and as structural materials for fusion reactors. The composites used in this study were composed of a SiC matrix obtained by chemical vapor infiltration associated with various fiber types (Tyranno Type-S, Tyranno SA Grade-3 and Hi-Nicalon Type-S) and with a PyC layer as the interphase. 12 MeV Au ions were used for irradiation up to 0.05 and 1 displacement per atom (dpa) fluences at room temperature and 800 °C. Analysis of both microstructure and composition of composites were performed by scanning electron microscopy (SEM), electron probe microanalysis and Raman spectroscopy. At room temperature and low fluence, Raman spectroscopy results showed that irradiation induces a disordered/distorted state into fibers and matrix. With increasing fluence, a total amorphization of these constituents occurs. The increase in the irradiation temperature leads to a damage recovery and partial recrystallization of samples. Image analysis performed from SEM micrographs highlights no significant change in fiber diameter and shape. However, SEM analysis suggests a longitudinal shrinkage of Tyranno Type-S fibers for the composite irradiated at 1 dpa at room temperature and 800 °C. These results are in complete agreement with conclusions from neutron irradiations suggesting an appropriate relevance of irradiations with 12 MeV Au.

  1. Fabrication and evaluation of mechanical properties of alkaline treated sisal/hemp fiber reinforced hybrid composite

    Science.gov (United States)

    Venkatesha Gupta, N. S.; Akash; Sreenivasa Rao, K. V.; kumar, D. S. Arun

    2016-09-01

    Fiber reinforced polymer composite have acquired a dominant place in variety of applications because of higher specific strength and modulus, the plant based natural fiber are partially replacing currently used synthetic fiber as reinforcement for polymer composites. In this research work going to develop a new material which posses a strength to weight ratio that for exceed any of the present material. The hybrid composite sisal/hemp reinforced with epoxy matrix has been developed by compression moulding technique according to ASTM standards. Sodium hydroxide (NAOH) was used as alkali for treating the fibers. The amount of reinforcement was varied from 10% to 50% in steps of 10%. Prepared specimens were examined for mechanical properties such as tensile strength, flexural strength, and hardness. Hybrid composite with 40wt% sisal/hemp fiber were found to posses higher strength (tensile strength = 53.13Mpa and flexural strength = 82.07Mpa) among the fabricated hybrid composite specimens. Hardness value increases with increasing the fiber volume. Morphological examinations are carried out to analyze the interfacial characteristics, internal structure and fractured surfaces by using scanning electron microscope.

  2. IJER@2014 Page 21 Prediction of Mechanical Properties of Hybrid Fiber Reinforced Polymer Composites

    Directory of Open Access Journals (Sweden)

    P Sivaraj

    2014-03-01

    Full Text Available Abstract— This work presents a systematic approach to evaluate and study the effect of process parameters on tensile flexural and impact strength of coir and bagasse fiber reinforced polyester-based hybrid composites and also predicts the properties of random oriented hybrid composites. The composite panel was fabricated using hand lay-up method to the size of 300mmx200mmx3mm with various weight percentage of natural fibers namely coir (10, 20 and 30 wt % and bagasse (10, 20 and 30 wt % combined with polyester resin. The mechanical properties testing such as tensile, flexural and impact strength were carried out for the samples cut from the fabricated composite panel to the dimensions as per ASTM standard. The significant contribution of mixing of fiber was determined by analysis of variance. The second-order polynomial curve fitting equations are modelled to predict the mechanical properties such as tensile, flexural and impact strength. Also scanning electron microscopy testing was conducted on tensile test specimen to find the fiber matrix interfacial adhesion.

  3. Feature guided waves (FGW) in fiber reinforced composite plates with 90° transverse bends

    Science.gov (United States)

    Yu, Xudong; Ratassepp, Madis; Fan, Zheng; Manogharan, Prabhakaran; Rajagopal, Prabhu

    2016-02-01

    Fiber reinforced composite materials have been increasingly used in high performance structures such as aircraft and large wind turbine blades. 90◦ composite bends are common in reinforcing structural elements, which are prone to defects such as delamination, crack, fatigue, etc. Current techniques are based on local inspection which makes the whole bend area scanning time consuming and tedious. This paper explores the feasibility of using feature guided waves (FGW) for rapid screening of 90◦ composite laminated bends. In this study, the behavior of the bend-guided wave in the anisotropic composite material is investigated through modal studies by applying the Semi-Analytical Finite Element (SAFE) method, also 3D Finite Element (FE) simulations are performed to visualize the results and to obtain cross validation. To understand the influence of the anisotropy, three-dimensional dispersion surfaces of the guided modes in flat laminated plates are obtained, showing the dependence of the phase velocity with the frequency and the fiber orientation. S H0-like and S 0-like bend-guided modes are identified with energy concentrated in the bend region, limiting energy radiation into adjacent plates and thus achieving increased inspection length. Finally, parametric studies are carried out to further investigate the properties of these two bend-guided modes, demonstrating the variation of the group velocity, the energy concentration, and the attenuation with the frequency.

  4. Properties Variation of Carbon Fiber Reinforced Composite for Marine Current Turbine in Seawater

    Directory of Open Access Journals (Sweden)

    Li Jing

    2016-01-01

    Full Text Available Turbine blade which are generally made of composite is a core device among components of tidal current power generator that converts the flow of tidal current into a turning force. Recent years, damages of composite turbine blades have been reported due to reasons like seawater degradation, lake of strength, manufacture etc. In this paper, water absorption, tensile, bending, longitudinal transverse shearing properties of carbon fiber reinforced plastic (CRP composite which would be applied to fabricate the marine current turbine blade has been investigated. Furthermore, the variations of properties with seawater immersion period were studied. The results indicated that the water absorption increased almost linearly at the beginning of immersion and then became stable. Tensile strength of specimen tended to decrease firstly and then recovered slightly. However, the longitudinal transverse shearing strength showed reverse variation trend comparing to tensile strength. And the bending property of specimens was depressed significantly. The properties variations in seawater shall be referenced to design and fabrication of composite marine current turbine blade.

  5. Modeling continuous-fiber reinforced polymer composites for exploration of damage tolerant concepts

    Science.gov (United States)

    Matthews, Peter J.

    This work aims to improve the predictive capability for fiber-reinforced polymer matrix composite laminates using the finite element method. A new tool for modeling composite damage was developed which considers important modes of failure. Well-known micromechanical models were implemented to predict material values for material systems of interest to aerospace applications. These generated material values served as input to intralaminar and interlaminar damage models. A three-dimensional in-plane damage material model was implemented and behavior verified. Deficiencies in current state-of-the-art interlaminar capabilities were explored using the virtual crack closure technique and the cohesive zone model. A user-defined cohesive element was implemented to discover the importance of traction-separation material constitutive behavior. A novel method for correlation of traction-separation parameters was created. This new damage modeling tool was used for evaluation of novel material systems to improve damage tolerance. Classical laminate plate theory was used in a full-factorial study of layerwise-hybrid laminates. Filament-wound laminated composite cylindrical shells were subjected to quasi-static loading to validate the finite element computational composite damage model. The new tool for modeling provides sufficient accuracy and generality for use on a wide-range of problems.

  6. Modeling of stress/strain behavior of fiber-reinforced ceramic matrix composites including stress redistribution

    Science.gov (United States)

    Mital, Subodh K.; Murthy, Pappu L. N.; Chamis, Christos C.

    1994-01-01

    A computational simulation procedure is presented for nonlinear analyses which incorporates microstress redistribution due to progressive fracture in ceramic matrix composites. This procedure facilitates an accurate simulation of the stress-strain behavior of ceramic matrix composites up to failure. The nonlinearity in the material behavior is accounted for at the constituent (fiber/matrix/interphase) level. This computational procedure is a part of recent upgrades to CEMCAN (Ceramic Matrix Composite Analyzer) computer code. The fiber substructuring technique in CEMCAN is used to monitor the damage initiation and progression as the load increases. The room-temperature tensile stress-strain curves for SiC fiber reinforced reaction-bonded silicon nitride (RBSN) matrix unidirectional and angle-ply laminates are simulated and compared with experimentally observed stress-strain behavior. Comparison between the predicted stress/strain behavior and experimental stress/strain curves is good. Collectively the results demonstrate that CEMCAN computer code provides the user with an effective computational tool to simulate the behavior of ceramic matrix composites.

  7. Processing and Characterization of Basalt Fiber Reinforced Ceramic Composites for High Temperature Applications Using Polymer Precursors

    Science.gov (United States)

    Cox, Sarah B.; Lui, Donovan; Gou, Jihua

    2014-01-01

    The development of high temperature structural composite materials has been very limited due to the high cost of the materials and the processing needed. Ceramics can take much higher temperatures, but they are difficult to produce and form in bulk volumes. Polymer Derived Ceramics (PDCs) begin as a polymer matrix, allowing a shape to be formed and cured and then to be pyrolized in order to obtain a ceramic with the associated thermal and mechanical properties. The two PDCs used in this development are polysiloxane and polycarbosilane. Polysiloxanes contain a silicon oxycarbide backbone when pyrolized up to 1000C. Polycarbosilane, an organosilicon polymer, contain a silicon-carbon backbone; around 1200C, beta-SiC begins to crystallize. The use of basalt in structural and high temperature applications has been under development for over 50 years, yet there has been little published research on the incorporation of basalt fibers as a reinforcement in composites. Basalt is a naturally occurring material found in volcanic rock. Continuous basalt fiber reinforced PDCs have been fabricated and tested for the applicability of this composite system as a high temperature structural composite material. Thermal and mechanical testing includes oxyacetylene torch testing and three point bend testing.

  8. Application of cold plasma technology in fiber-reinforced composite materials

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    A study is presented concerning a cold plasma technique for improving the bondability of highstrength high-modulus multi-filament polyethylene fibers to polymer matrices and the fibers impregnation with the objective to fabricate composite materials (CMs). Strong bonding between the matrixes and reinforcing fibers during the production of composites appears in the case if interaction is chemical. The value of the activation energy of the chemical interaction for very high performance polyethylene fiber was estimated. It was 1.14 eV. This allows using the cold plasma technique for producing CMs. In order to understand the effect of cold plasma treatment treated and untreated fibers were used to fabricate CMs. The strong bond between the matrix and plasma-activated fibers affects both the properties and failure mode of composite. The properties and failure modes were compared to those of CMs reinforced with untreated fibers. After plasma treatment the properties of CMs are increased. CMs are broken as a unit whole under tension. The ideas of the activating the fibers by cold plasma treatment above the activation energy of the chemical interaction may be extended over other types of the fibers and matrices to produce new types of fiber-reinforced composite materials with high physicomechanical indices.

  9. Ballistic impact damage and penetration mechanics of fiber-reinforced composite laminates

    Science.gov (United States)

    Patts, Henry Michael

    2000-10-01

    Experimental and theoretical studies were performed to characterize and model the processes of damage evolution and resulting penetration failure of graphite fiber-reinforced epoxy resin composite laminates ("structural grade") under ballistic impact. In contrast to the local yielding demonstrated by ductile isotropic materials, the penetration failure of fiber-reinforced composites produced extensive fragmentation of material with multiple modes of damage propagation such as "delamination," "interfiber matrix splitting," "transverse fiber cuts," and "through-the-thickness plugging." Due to the formation of damage zones in three-dimensional scale, the increase in target thickness raised the amount of kinetic energy absorption for full penetration in a "non-linear" fashion in fiber composites unlike the linear correlation for isotropic material such as polycarbonate and aluminum. Interfiber matrix splitting and delamination were found to be the first sign of structural deterioration occurring far below V50 and precede transverse cutting of fibers and plugging. The development of interfiber splitting into delamination of composites is explained by relying on the contact mechanics of a spherical indentor. Matrix splits on adjacent plies formed one pair of geometrical "wedges" at the ply interface, resulting in a delamination zone connected through an "isthmus." Contained in this free ply region, stress concentration readily led to transverse cutting (approximately at 85 percent of the V50) of plies when longitudinal stress of the reinforcing fibers reaches a critical level for fracture. The observed distribution of the damage leading to transverse fiber cuts was modeled by idealizing a circular target panel of staircase laminate into three zones with different values of bending stiffness due to the progression of damage. In "three-zone" model, the energy absorbed by the panel were represented in three forms of potential energy; surface free energy due to delamination

  10. Numerical and experimental studies of delamination detection in short fiber reinforced composites using Lamb waves

    Science.gov (United States)

    Kudela, Pawel; Radzienski, Maciej; Ostachowicz, Wieslaw

    2016-04-01

    The aim of this paper is to present aspects of Lamb wave propagation in randomly oriented short fiber reinforce composites with delamination. Prediction of elastic constants is based on mechanics of composites, rule of mixture and total mass balance tailored to the spectral element mesh composed of 3D brick elements. Piezoelectric excitation as well as glue layer are taken into account. Complex full wave field includes multiple reflections at short fibers. This wave pattern is also obtained by the use of laser vibrometry confirming good quality of the model. Further studies are related to symmetrical and non-symmetrical delamination in respect to the thickness of the composite plate. Square delamination of the side length 10 mm is investigated. It has been found that reflections from delamination are mostly superimposed with reflections coming from short fibers. Hence, delamination detection by direct analysis of wave propagation pattern on the surface of the plate is ineffective. However, adaptive wavenumber filtering method overcome these difficulties and enables not only to detect the delamination but also is helpful for delamination size estimation. Moreover, the method is more effective if the full wavefield measurements are acquired on the surface of the plate which is closer to the delamination.

  11. Development of multifunctional fiber reinforced polymer composites through ZnO nanowire arrays

    Science.gov (United States)

    Malakooti, Mohammad H.; Patterson, Brendan A.; Hwang, Hyun-Sik; Sodano, Henry A.

    2016-04-01

    Piezoelectric nanowires, in particular zinc oxide (ZnO) nanowires, have been vastly used in the fabrication of electromechanical devices to convert wasted mechanical energy into useful electrical energy. Over recent years, the growth of vertically aligned ZnO nanowires on various structural fibers has led to the development of fiber-based nanostructured energy harvesting devices. However, the development of more realistic energy harvesters that are capable of continuous power generation requires a sufficient mechanical strength to withstand typical structural loading conditions. Yet, a durable, multifunctional material system has not been developed thoroughly enough to generate electrical power without deteriorating the mechanical performance. Here, a hybrid composite energy harvester is fabricated in a hierarchical design that provides both efficient power generating capabilities while enhancing the structural properties of the fiber reinforced polymer composite. Through a simple and low-cost process, a modified aramid fabric with vertically aligned ZnO nanowires grown on the fiber surface is embedded between woven carbon fabrics, which serve as the structural reinforcement as well as the top and the bottom electrodes of the nanowire arrays. The performance of the developed multifunctional composite is characterized through direct vibration excitation and tensile strength examination.

  12. Physical and Mechanical Characteristics of Kevlar Fiber-Reinforced PC/ABS Composites

    Directory of Open Access Journals (Sweden)

    Kuljira Sujirote

    2012-01-01

    Full Text Available In this research, the composites between polycarbonate (PC and acrylonitrile-butadiene-styrene (ABS alloy and Kevlar fiber were prepared. The flexural and tensile properties of PC/ABS alloy and its composites were determined using a universal testing machine. The synergistic behavior of flexural modulus was observed for all regions of PC contents, while the synergism of flexural strength and tensile strength were found in some PC contents. It was found that the optimum weight ratio of PC:ABS was 60:40. In the Kevlar Fiber-reinforced PC/ABS composite system at PC:ABS of 60:40, both flexural modulus and strength were increased with matrix contents. Additionally, the flexural strength drastically increased with the matrix content and then reached the maximum value of 167 MPa at the matrix content of 33.4 wt%. The results from peel test, water contact measurement, and scanning electron microscopy (SEM reveal that the interfacial adhesion between the Kevlar fiber and the polymer matrix could be improved by increasing the PC content in the matrix.

  13. Standard Guide for Recording Mechanical Test Data of Fiber-Reinforced Composite Materials in Databases

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2000-01-01

    1.1 This guide provides a common format for mechanical test data for composite materials for two purposes: (1) to establish data reporting requirements for test methods and ( 2) to provide information for the design of material property databases. This guide should be used in combination with Guide E 1309 which provides similar information to identify the composite material tested. 1.2 These guidelines are specific to mechanical tests of high-modulus fiber-reinforced composite materials. Types of tests considered in this guide include tension, compression, shear, flexure, open/filled hole, bearing, fracture toughness, and fatigue. The ASTM standards for which this guide was developed are listed in . The guidelines may also be useful for additional tests or materials. 1.3 This guide is the second part of a modular approach for which the first part is Guide E 1309. Guide E 1309 serves to identify the material, and this guide serves to describe mechanical testing procedures and variables and to record results....

  14. Experimental Investigation of Effect of Aluminum Filler Material on Thermal Properties of Palmyra Fiber Reinforced Composite

    Directory of Open Access Journals (Sweden)

    J. Pavanu Sai

    2014-12-01

    Full Text Available Natural fiber composites are renewable, cheap, completely or partially recyclable, carbon neutral and biodegradable. Their easy availability, lower density, higher specific properties, lower cost, satisfactory mechanical and thermal properties, non-corrosive nature, lesser abrasion to processing equipment, makes them an attractive ecological alternative to glass, carbon or other man-made synthetic fibers. Natural fiber composites are generally very good thermal insulators and thus cannot be used where thermal conduction is desirable. Increase in thermal conduction may be done by adding metal filler powders to the matrix. In this work, the effect of aluminum filler material on thermal properties of chemically treated palmyra fiber reinforced composites is investigated. Thermal properties studied include thermal conductivity, specific heat capacity, thermal diffusivity, thermal degradation and stability. Five different samples with 0%, 25%, 50%, 75%, 100% aluminum powder are considered. With the addition of aluminum filler powder, thermal conductivity increases, specific heat capacity decreases, thermal diffusivity increases and thermal stability improves with maximum at 50% aluminum powder.

  15. Mechanical, Thermal Degradation, and Flammability Studies on Surface Modified Sisal Fiber Reinforced Recycled Polypropylene Composites

    Directory of Open Access Journals (Sweden)

    Arun Kumar Gupta

    2012-01-01

    Full Text Available The effect of surface treated sisal fiber on the mechanical, thermal, flammability, and morphological properties of sisal fiber (SF reinforced recycled polypropylene (RPP composites was investigated. The surface of sisal fiber was modified with different chemical reagent such as silane, glycidyl methacrylate (GMA, and O-hydroxybenzene diazonium chloride (OBDC to improve the compatibility with the matrix polymer. The experimental results revealed an improvement in the tensile strength to 11%, 20%, and 31.36% and impact strength to 78.72%, 77%, and 81% for silane, GMA, and OBDC treated sisal fiber reinforced recycled Polypropylene (RPP/SF composites, respectively, as compared to RPP. The thermogravimetric analysis (TGA, differential scanning calorimeter (DSC, and heat deflection temperature (HDT results revealed improved thermal stability as compared with RPP. The flammability behaviour of silane, GMA, and OBDC treated SF/RPP composites was studied by the horizontal burning rate by UL-94. The morphological analysis through scanning electron micrograph (SEM supports improves surface interaction between fiber surface and polymer matrix.

  16. Initial adhesion of glass-fiber-reinforced composite to the surface of porcine calvarial bone.

    Science.gov (United States)

    Tuusa, S M R; Lassila, L V J; Matinlinna, J P; Peltola, M J; Vallittu, P K

    2005-11-01

    The aim of this preliminary study was to compare the initial bond strength of the glass-fiber-reinforced composite veil to the surface of the porcine calvarial compact bone using different adhesives. Fiber-reinforced composite (FRC) made of E-glass fiber veil with the BisGMA-PMMA resin system was used in the study. For the shear bond strength test, porcine calvarial bone cubes were mounted into resin matrix. FRC-veil discs were bonded to compact bone with different types of adhesives: (A) BisGMA-HEMA based (3M-ESPE Scotchbond Multi-Purpose Adhesive), (B) 4-META/UDMA/BisGMA based (Unifil Bond Bonding Agent) and MDP based (Clearfil Se Bond adhesive), (C) UDMA/BisGMA/PMMA-based experimental adhesive, and (D) silane-based (APS, ICS, MPS) experimental adhesives. The surface of the bone was mechanically roughened and was either used as such, treated with dental primers (Unifil Bond Self-etching Primer, Clearfil Se Bond Primer), or treated with an experimental silane mixture (APS, ICS, MPS), or with a mixture of the experimental silane liquid and Clearfil Se Bond Primer. The 3M-ESPE Scotchbond Multi-Purpose Adhesive and UDMA/BisGMA/PMMA experimental adhesive gave poor results in the shear bond test (0.58 and 0.40 MPa, respectively). Unifil Bond Bonding Agent and Clearfil Se Bond adhesive with respective primers markedly improved the shear bond strength; with Unifil the result was 3.40 MPa, and with Clearfil it was 6.19 MPa. When the bone surface was primed with a mixture of Clearfil Se Bond Primer and Clearfil Porcelain Bond Activator, the Clearfil Se Bond adhesive-impregnated FRC veil gave the best adhesion to the bone surface in this test: 9.50 MPa. The addition of bioactive glass granules between the veil and the bone lowered the shear bond strength in the test system described above to 6.72 MPa. The test systems with the silane mixture were also promising. In the SEM study, it was found that the mechanical treatment reveals the pores of the bone surface. Chemical

  17. Investigating the influence of alkalization on the mechanical and water absorption properties of coconut and sponge fibers reinforced polypropylene composites

    Directory of Open Access Journals (Sweden)

    Okikiola Ganiu AGBABIAKA

    2014-11-01

    Full Text Available Natural fibers are products made from renewable agricultural and forestry feedstock, which can include wood, grasses, and crops, as well as wastes and residues. There are two primary ways these fibers are used: to create polymers or as reinforcement and filler. Thermoplastic polymer may be reinforced or filled using natural fibers such as coir, sponge, hemp, flax, or sisal. This paper focused on the influence of alkalization (NaOH treatment on the mechanical and water absorption properties of selected natural fibers (coconut and sponge fibers reinforced polypropylene composites. In this study, coconut and sponge fiber were extracted from its husk by soaking them in water and was dried before it was cut into 10mm length. Those fibers were chemically treated with sodium hydroxide (NaOH in a shaking water bath before it was used as reinforcement in polypropylene composite. The reinforced polypropylene composite was produced by dispersing the coconut fibers randomly in the polypropylene before it was fabricated in a compression molding machine where the composite was produced. The fiber content used were; 2%wt, 4%wt, 6%wt, 8%wt and 10%wt. Tensile and flexural properties was observed from universal testing machine while water absorption test was carried out on the samples for seven (7 days. It was observed that the influence of NaOH treatment highly enhanced the Flexural and water absorption properties of sponge fiber reinforced polypropylene composites than coconut fiber reinforced composite samples.

  18. Nondestructive testing of externally reinforced structures for seismic retrofitting using flax fiber reinforced polymer (FFRP) composites

    Science.gov (United States)

    Ibarra-Castanedo, C.; Sfarra, S.; Paoletti, D.; Bendada, A.; Maldague, X.

    2013-05-01

    Natural fibers constitute an interesting alternative to synthetic fibers, e.g. glass and carbon, for the production of composites due to their environmental and economic advantages. The strength of natural fiber composites is on average lower compared to their synthetic counterparts. Nevertheless, natural fibers such as flax, among other bast fibers (jute, kenaf, ramie and hemp), are serious candidates for seismic retrofitting applications given that their mechanical properties are more suitable for dynamic loads. Strengthening of structures is performed by impregnating flax fiber reinforced polymers (FFRP) fabrics with epoxy resin and applying them to the component of interest, increasing in this way the load and deformation capacities of the building, while preserving its stiffness and dynamic properties. The reinforced areas are however prompt to debonding if the fabrics are not mounted properly. Nondestructive testing is therefore required to verify that the fabric is uniformly installed and that there are no air gaps or foreign materials that could instigate debonding. In this work, the use of active infrared thermography was investigated for the assessment of (1) a laboratory specimen reinforced with FFRP and containing several artificial defects; and (2) an actual FFRP retrofitted masonry wall in the Faculty of Engineering of the University of L'Aquila (Italy) that was seriously affected by the 2009 earthquake. Thermographic data was processed by advanced signal processing techniques, and post-processed by computing the watershed lines to locate suspected areas. Results coming from the academic specimen were compared to digital speckle photography and holographic interferometry images.

  19. A Constitutive Formulation for the Linear Thermoelastic Behavior of Arbitrary Fiber-Reinforced Composites

    Directory of Open Access Journals (Sweden)

    Melek Usal

    2010-01-01

    Full Text Available The linear thermoelastic behavior of a composite material reinforced by two independent and inextensible fiber families has been analyzed theoretically. The composite material is assumed to be anisotropic, compressible, dependent on temperature gradient, and showing linear elastic behavior. Basic principles and axioms of modern continuum mechanics and equations belonging to kinematics and deformation geometries of fibers have provided guidance and have been determining in the process of this study. The matrix material is supposed to be made of elastic material involving an artificial anisotropy due to fibers reinforcing by arbitrary distributions. As a result of thermodynamic constraints, it has been determined that the free energy function is dependent on a symmetric tensor and two vectors whereas the heat flux vector function is dependent on a symmetric tensor and three vectors. The free energy and heat flux vector functions have been represented by a power series expansion, and the type and the number of terms taken into consideration in this series expansion have determined the linearity of the medium. The linear constitutive equations of the stress and heat flux vector are substituted in the Cauchy equation of motion and in the equation of conservation of energy to obtain the field equations.

  20. Thermo-physical Properties of Continuous Carbon Fiber Reinforced Copper Matrix Composites

    Institute of Scientific and Technical Information of China (English)

    曹金华; 黄俊波; 陈先有

    2007-01-01

    Continuous carbon fiber reinforced copper matrix composites with 70%(volume fraction)of carbon fibers prepared by squeeze casting technique have been used for investigation of the coefficient of thermal expansion(CTE)and thermal conductivity.Thermo-physical properties have been measured in both, longitudinal and transversal directions to the fiber orientation.The results showed that Cf/Cu composites may be a suitable candidate for heat sinks because of its good thermo-physical properties e.g.the low CTE(4.18×10-6/K)in longitudinal orientation and(14.98×10-6/K)in transversal orientation at the range of 20-50℃,a good thermal conductivity(87.2 W/m·K)in longitudinal orientation and(58.2 W/m·K)in transversal orientation.Measured CTE and thermal conductivity values are compared with those predicted by several well-known models.Eshelby model gave better results for prediction of the CTE and thermal conductivity of the unidirectional composites.

  1. Durability of carbon fiber reinforced shape memory polymer composites in space

    Science.gov (United States)

    Jang, Joon Hyeok; Hong, Seok Bin; Ahn, Yong San; Kim, Jin-Gyun; Nam, Yong-Youn; Lee, Geun Ho; Yu, Woong-Ryeol

    2016-04-01

    Shape memory polymer (SMP) is one of smart polymers which exhibit shape memory effect upon external stimuli. Recently, shape memory polymer composites (SMPCs) have been considered for space structure instead of shape memory alloys due to their deformability, lightweight and large recovery ratio, requiring characterization of their mechanical properties against harsh space environment and further prediction of the durability of SMPCs in space. As such, the durability of carbon fiber reinforced shape memory polymer composites (CF-SMPCs) was investigated using accelerated testing method based on short-term testing of CF-SMPCs in harsh condition. CF-SMPCs were prepared using woven carbon fabrics and a thermoset SMP via vacuum assisted resin transfer molding process. Bending tests with constant strain rate of CF-SMPCs were conducted using universal tensile machine (UTM) and Storage modulus test were conducted using dynamic mechanical thermal analysis (DMTA). Using the results, a master curve based on time-temperature superposition principle was then constructed, through which the mechanical properties of CF-SMPCs at harsh temperature were predicted. CF-SMPCs would be exposed to simulated space environments under ultra-violet radiations at various temperatures. The mechanical properties including flexural and tensile strength and shape memory properties of SMPCs would be measured using UTM before and after such exposures for comparison. Finally, the durability of SMPCs in space would be assessed by developing a degradation model of SMPC.

  2. Characterization of a New Fully Recycled Carbon Fiber Reinforced Composite Subjected to High Strain Rate Tension

    Science.gov (United States)

    Meftah, H.; Tamboura, S.; Fitoussi, J.; BenDaly, H.; Tcharkhtchi, A.

    2017-08-01

    The aim of this study is the complete physicochemical characterization and strain rate effect multi-scale analysis of a new fully recycled carbon fiber reinforced composites for automotive crash application. Two composites made of 20% wt short recycled carbon fibers (CF) are obtained by injection molding. The morphology and the degree of dispersion of CF in the matrixes were examined using a new ultrasonic method and SEM. High strain tensile behavior up to 100 s-1 is investigated. In order to avoid perturbation due to inertial effect and wave propagation, the specimen geometry was optimized. The elastic properties appear to be insensitive to the strain rate. However, a high strain rate effect on the local visco-plasticity of the matrix and fiber/matrix interface visco-damageable behavior is emphasized. The predominant damage mechanisms evolve from generalized matrix local ductility at low strain rate regime to fiber/matrix interface debonding and fibers pull-out at high strain rate regime.

  3. Fiber-coatings for fiber-reinforced mullite/mullite composites

    Energy Technology Data Exchange (ETDEWEB)

    Nubian, K.; Wahl, G. [Technische Univ. Braunschweig (Germany). Inst. fuer Oberflaechentechnik und Plasmatechnische Werkstoffentwicklung; Saruhan, B.; Schneider, H. [Technische Univ. Braunschweig (Germany). Inst. fuer Oberflaechentechnik und Plasmatechnische Werkstoffentwicklung; DLR, Deutsches Zentrum fuer Luft- und Raumfahrt e.v., Koeln (Germany)

    2001-08-01

    Mullite-based fiber-reinforced composites are favorite candidates for the application in combustion chambers of gas turbines. The application requires damage tolerance, temperature and oxidation-resistance at high temperatures (> 1200 C) over long terms. In order to realize crack deflection and fiber pull-out, an interphase coating of the mullite fibers (Nextel{sup TM} 720) is necessary to obtain a weak bonding between fibers and matrix. Two systems of interphases produced by CVD were described. The first system is a carbon/metal-oxide double layer (C/ZrO{sub 2}, C/Al{sub 2}O{sub 3}). Properties of the resulting composites after heat-treatment (1300 C, 1000 h) under cyclic and continuous heating conditions were described. The second system is the codeposition of La{sub 2}O{sub 3} and Al{sub 2}O{sub 3} on the fibers. After heat-treatment at 1300 C lanthanum hexaluminate (LaAl{sub 11}O{sub 18}) with a magneto plumbite structure containing sliding planes should be formed. (orig.)

  4. Thermal degradation of fiber coatings in mullite-fiber-reinforced mullite composites

    Energy Technology Data Exchange (ETDEWEB)

    Schmuecker, M.; Schneider, H. [German Aerospace Research Establishment, Koeln (Germany). Inst. for Materials Research; Chawla, K.K.; Xu, Z.R. [New Mexico Inst. of Mining and Technology, Socorro, NM (United States). Dept. of Materials and Metallurgical Engineering

    1997-08-01

    The thermal degradation behavior of single-layer BN and of double-layer BN/SiC chemically vapor-deposited fiber coatings in mullite-fiber-reinforced mullite composites was investigated by means of transmission electron microscopy after processing and heat treatment of the composites at 1000, 1200, and 1300 C for 6 h in air. The single-layer BN coatings were {approximately}0.7 {micro}m thick and consisted of turbostratic BN with (0001) basal planes lying parallel to the surfaces of the fibers plus nanosized areas that had no preferential orientation. This microstructure remained unchanged up to 1000 C; however, distinct coarsening of the randomly oriented BN crystallites occurred in the temperature range of 1000--1200 C. The single-layer BN coatings were stable against oxidation, up to 1200 C. At higher temperatures, degradation of the coatings via oxidation occurred. Double-layer BN/SiC coating systems consisted of BN that was 0.08 {micro}m thick and SiC layers that were 0.16 {micro}m thick and deposited onto the mullite fibers. The turbostratic BN was highly anisotropic and did not undergo any microstructural change, up to 1300 C. The outer SiC layer of the double-layer coating system improved the oxidation resistance of BN in the 1200--1300 C temperature range, despite a partial oxidation of SiC to SiO{sub 2}.

  5. 3D-WOVEN FIBER-REINFORCED COMPOSITE FOR CAD/CAM DENTAL APPLICATION.

    Science.gov (United States)

    Petersen, Richard; Liu, Perng-Ru

    2016-05-01

    Three-dimensional (3D)-woven noncrimp fiber-reinforced composite (FRC) was tested for mechanical properties in the two principal directions of the main XY plane and compared to different Computer-Aided-Design/Computer-Aided-Machining (CAD/CAM) Dental Materials. The Dental Materials included ceramic with Vitablock Mark II®, ProCAD®, InCeram® Spinel, InCeram® Alumina and InCeram® Zirconia in addition to a resin-based 3M Corp. Paradigm® particulate-filled composite. Alternate material controls included Coors 300 Alumina Ceramic and a tungsten carbide 22% cobalt cermet. The 3D-woven FRC was vacuum assisted resin transfer molding processed as a one-depth-thickness ~19-mm preform with a vinyl-ester resin and cut into blocks similar to the commercial CAD/CAM Dental Materials. Mechanical test samples prepared for a flexural three-point span length of 10.0 mm were sectioned for minimum-depth cuts to compare machinability and fracture resistance between groups. 3D-woven FRC improved mechanical properties with significant statistical differences over all CAD/CAM Dental Materials and Coors Alumina Ceramic for flexural strength (pfracture (p<0.001), strain energy release (p<0.05), critical stress intensity factor (p<0.001) and strain (p<0.001).

  6. Carbon fiber-reinforced cyanate ester/nano-ZrW2O8 composites with tailored thermal expansion.

    Science.gov (United States)

    Badrinarayanan, Prashanth; Rogalski, Mark K; Kessler, Michael R

    2012-02-01

    Fiber-reinforced composites are widely used in the design and fabrication of a variety of high performance aerospace components. The mismatch in coefficient of thermal expansion (CTE) between the high CTE polymer matrix and low CTE fiber reinforcements in such composite systems can lead to dimensional instability and deterioration of material lifetimes due to development of residual thermal stresses. The magnitude of thermally induced residual stresses in fiber-reinforced composite systems can be minimized by replacement of conventional polymer matrices with a low CTE, polymer nanocomposite matrix. Zirconium tungstate (ZrW(2)O(8)) is a unique ceramic material that exhibits isotropic negative thermal expansion and has excellent potential as a filler for development of low CTE polymer nanocomposites. In this paper, we report the fabrication and thermal characterization of novel, multiscale, macro-nano hybrid composite laminates comprising bisphenol E cyanate ester (BECy)/ZrW(2)O(8) nanocomposite matrices reinforced with unidirectional carbon fibers. The results reveal that incorporation of nanoparticles facilitates a reduction in CTE of the composite systems, which in turn results in a reduction in panel warpage and curvature after the cure because of mitigation of thermally induced residual stresses.

  7. MULTIPLE SCATTERING AND DYNAMIC STRESS ANALYSIS OF ELASTIC WAVES IN A FIBER-REINFORCED COMPOSITE WITH INTERFACES

    Institute of Scientific and Technical Information of China (English)

    李凤明; 胡超; 徐敏强; 黄文虎

    2003-01-01

    Based on the theory of elastic dynamics,multiple scattering of elastic waves and dynamic stress concentrations in fiber-reinforced composite are studied.The analytical expressions of elastic waves in different regions are presented.The mode coefficients of elastic waves are determined in accordance with the continuous conditions of displacement and stress on the boundary of the multiinterfaces.By using the addition theorem of Hankel functions,the formula of scattered wave fields in different local coordinates are transformed into those in one local coordinate to determine the unknown coefficients and dynamic stress concentration factors (DSCFs).The influences of the distance between two inclusions,material properties and structural size on the DSCFs near the interfaces are analyzed.As examples,the numerical results of DSCFs near the interfaces for two kinds of fiber-reinforced composites are presented and discussed.

  8. Pasak Customized Fiber Reinforced Composite Indirect pada Gigi Incisivus Lateralis Kiri Atas dengan Dinding Saluran Akar yang Tipis

    Directory of Open Access Journals (Sweden)

    Monika Prima Dewi Ayuningtyas Subroto

    2015-06-01

    restoration of a non vital post root canal treatment tooth with thin root canal walls using indirect customized fiber-reinforced composite post. A 27-year-old female patient with over instrumentation in root canal of the upper left lateral incisor was referred to the Department of Conservative Dentistry. The radiograph examination finds that there was a very thin wall of the remaining root canal structure. The restoration was carried out in 3 visits. In the first visit, post canal impression was obtained using double impression technique. Indirect customized fiber reinforced composite post was made in the mold using composite resin Premise Indirect (Kerr reinforced with fiber band (Construct, Kerr. The formed post and core were light cured for 20 seconds, and then refined by oven polymerization for 20 minutes. In the second visit, the post was inserted and crown impression was obtained using double impression technique. In the third visit, the jacket crown was inserted. The root canal treated tooth with remaining thin post canal wall could be restored with indirect customized fiber reinforced composite.

  9. Study on the laser irradiation effects on carbon fiber reinforced resin composite subjected to tangential gas flow loading

    Science.gov (United States)

    Chen, Minsun; Jiang, Houman; Jiao, Luguang; Li, Junshen; Liu, Zejin

    2013-05-01

    The irradiation effects of 976nm continuous-wave laser on carbon fiber reinforced E-51 resin composite is studied experimentally, with a 0.4Ma tangential airflow or 0.4Ma tangential nitrogen gas flow on the target surface. In order to simulate the thermal response of fiber reinforced resin composite materials subjected to combined laser and tangential gas flow loading, a three-dimensional thermal response model of resin composite materials is developed. In the model, the thermal decomposition of resin is described by a multi-step model. The motion of the decomposition gas is assumed to be one-dimensional, for the case that the laser spot is significantly larger than the thickness of the sample. According the above assumption, the flow of the decomposition gas is considered in the three-dimensional model without introducing any mechanical quantities. The influences of the tangential gas flow, the outflow of the thermal decomposition gas and the ablation-including phase change ablation or oxidative ablation-of the surface material on the laser irradiation effects are included in the surface boundary conditions. The three-dimensional thermal response model is calculated numerically by use of the modified smooth particle hydrodynamics (MSPH) method which is coded with FORTRAN. The model is tested by experimentally measuring the temperature profiles during carbon fiber reinforced E-51 resin composite subjected to combined laser and tangential gas flow. The predicted temperature profiles are in good agreement with experimental temperatures obtained using thermocouples.

  10. STUDY ON THE EFFECTS OF BREAKAGE OF SINGLE FIBER ON CREEP BEHAVIOR OF FIBER REINFORCED COMPOSITES

    Institute of Scientific and Technical Information of China (English)

    X.J. Shao; Y.P. Jiang; Z. F. Yue

    2004-01-01

    A 3-D micro cell model with multi-fibers has been presented to study the effects of breakage of single fiber on the whole creep behavior of fiber reinforced composites by finite element method (FEM). Before the fiber breakage, the stresses of all fibers are identical. With the creep time increasing, stress in fiber increases but stress in matrix decreases. It is assumed that the fiber breakage occurs when the stress in fiber reaches a critical value. The stress redistribution resulted from the breakage of fiber has been obtained. The influence on the axial stress of the broken fiber is local. The stress in the all fiber sections is not uniform. There is a local stress concentration in the matrix. And this stress concentration in the matrix is more and more serious with the creep deformation. The stress transference of the loading due to the fiber breakage has been studies numerically. It is found that the fibers near to the broken fiber will take over more loading.

  11. Parametric Study on Dynamic Response of Fiber Reinforced Polymer Composite Bridges

    Directory of Open Access Journals (Sweden)

    Woraphot Prachasaree

    2015-01-01

    Full Text Available Because of high strength and stiffness to low self-weight ratio and ease of field installation, fiber reinforced polymer (FRP composite materials are gaining popularity as the materials of choice to replace deteriorated concrete bridge decks. FRP bridge deck systems with lower damping compared to conventional bridge decks can lead to higher amplitudes of vibration causing dynamically active bridge deck leading serviceability problems. The FRP bridge models with different bridge configurations and loading patterns were simulated using finite element method. The dynamic response results under varying FRP deck system parameters were discussed and compared with standard specifications of bridge deck designs under dynamic loads. In addition, the dynamic load allowance equation as a function of natural frequency, span length, and vehicle speed was proposed in this study. The proposed dynamic load allowance related to the first flexural frequency was presented herein. The upper and lower bounds’ limits were established to provide design guidance in selecting suitable dynamic load allowance for FRP bridge systems.

  12. Solidification microstructures in a short fiber reinforced alloy composite containing different fiber fractions

    Directory of Open Access Journals (Sweden)

    JING Qing-xiu

    2006-02-01

    Full Text Available The solidification microstructures and micro-segregation of a fiber reinforced Al-9 Cu alloy, containing different volume fractions of Al2O3 short fibers about 6 μm diameter and made by squeeze casting have been studied. The results indicate that as volume fraction of fiber Vf increases, the size of final grains becomes finer in the matrix. If λf /λ>1, the fibers have almost no influence on the solidification behavior of the matrix, so the final grains grow coarse, where λf is the average inter-fiber spacing and λ is the secondary dendrite arm spacing. While if λf /λ<1, the growth of crystals in the matrix is affected significantly by the fibers and the grain size is reduced to the value of the inter-fiber spacing. The fibers influence the average length of a solidification volume element L of the matrix and also influence the solidification time θt of the matrix. As a result of fibers influencing L and θt, the micro-segregation in the matrix is improved when the composite contains more fibers, although the level of the improvement is slight. The Clyne-Kurz model can be used to semi-quantitatively analyze the relationship between Vf and the volume fraction fe of the micro-segregation eutectic structure.

  13. Flexural strengths of conventional and nanofilled fiber-reinforced composites: a three-point bending test.

    Science.gov (United States)

    Sfondrini, Maria Francesca; Massironi, Sarah; Pieraccini, Giulia; Scribante, Andrea; Vallittu, Pekka K; Lassila, Lippo V; Gandini, Paola

    2014-02-01

    The purpose of this study was to evaluate the effect of the introduction of nanofillers on the mechanical properties of fiber-reinforced composites (FRCs) for stabilization and conservative treatment of multiple traumatized anterior teeth. In particular, the aim of the research was to point out the force levels of two sizes (diameters 0.6 and 0.9 mm) of both conventional and nanofilled FRCs. Eighty FRCs samples were divided into eight groups, each consisting of 10 specimens. Conventional (groups 1, 2, 3, and 4) and nanofilled (groups 5, 6, 7, and 8) FRC samples were evaluated. Each FRC was tested in two diameters (0.6 and 0.9 mm) and under two deflections (1 and 2 mm). Each sample was polymerized with the same halogen curing unit and then evaluated with a 3-point bending test on a universal testing machine after 48 h of dry storage. Nanofilled FRCs showed significantly higher load values than conventional FRCs. Moreover, 0.9-mm-diameter FRCs showed significantly higher load value than 0.6-mm-diameter FRCs. Specimens tested at 2-mm deflection showed significantly higher load values than those tested at 1-mm deflection. Nanofilled FRCs showed significantly higher load values than conventional FRCs. Higher flexural strength values were recorded with 1-mm deflection for both FRC tested. © 2013 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

  14. Solidification microstructures in a short fiber reinforced alloy composite containing different fiber fractions

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    The solidification microstructures and micro-segregation of a fiber reinforced Al-9 Cu alloy, containing different volurne fractions of Al2O3 short fibers about 6μm diameter and made by squeeze casting have been studied. The results indicate that as volume fraction of fiber Vf increases, the size of final grains becomes finer in the matrix. If λf/λ> 1, the fibers have almost no influence on the solidification behavior of the matrix, so the final grains grow coarse, where λf is the average inter-fiber spacing and λ is the secondary dendrite arm spacing. While if λf/λ< 1, the growth of crystals in the matrix is affected significantly by the fibers and the grain size is reduced to the value of the inter-fiber spacing. The fibers influence the average length of a solidification volume element L of the matrix and also influence the solidification time θt of the matrix. As a result of fibers influencing L and θt, the micro-segregation in the matrix is improved when the composite contains more fibers, although the level of the improvement is slight. The Clyne-Kurz model can be used to semi-quantitatively analyze the relationship between Vf and the volume fraction fe of the micro-segregation eutectic structure.

  15. Mechanical properties related to the microstructure of seven different fiber reinforced composite posts

    Science.gov (United States)

    Alonso de la Peña, Víctor; Caserío Valea, Martín; Guitián Rivera, Francisco

    2016-01-01

    PURPOSE The aim of this in vitro study was to evaluate the mechanical properties (bending strength and hardness) of seven different fiber reinforced composite posts, in relation to their microstructural characteristics. MATERIALS AND METHODS Two hundred eighty posts were divided into seven groups of 40, one group for each type of post analyzed. Within each group, 15 posts were subjected to three-point bending strength test, 15 to a microhardess meter for the Knoop hardness, and 10 to Scanning Electron Microscope in order to determine the diameter of the fibers and the percentage of fibers embedded in the matrix. To compare the flexural strength in relation to the type of fiber, matrix, and the hardness of the posts, a Kruskal-Wallis H test was used. The Jonckheere-Terpstra test was used to determine if the volume percent of fibers in the post influenced the bending strength. RESULTS The flexural strength and the hardness depended on the type of fibers that formed the post. The lower flexural strength of a post could be due to deficient bonding between the fiber and the resin matrix. CONCLUSION According to the results, other factors, besides the microstructural characteristics, may also influence the mechanical properties of the post. The feature that has more influence on the mechanical properties of the posts is the type of fiber. PMID:28018560

  16. Flexural Properties of E Glass and TR50S Carbon Fiber Reinforced Epoxy Hybrid Composites

    Science.gov (United States)

    Dong, Chensong; Sudarisman; Davies, Ian J.

    2013-01-01

    A study on the flexural properties of E glass and TR50S carbon fiber reinforced hybrid composites is presented in this paper. Specimens were made by the hand lay-up process in an intra-ply configuration with varying degrees of glass fibers added to the surface of a carbon laminate. These specimens were then tested in the three-point bend configuration in accordance with ASTM D790-07 at three span-to-depth ratios: 16, 32, and 64. The failure modes were examined under an optical microscope. The flexural behavior was also simulated by finite element analysis, and the flexural modulus, flexural strength, and strain to failure were calculated. It is shown that although span-to-depth ratio shows an influence on the stress-strain relationship, it has no effect on the failure mode. The majority of specimens failed by either in-plane or out-of-plane local buckling followed by kinking and splitting at the compressive GFRP side and matrix cracking combined with fiber breakage at the CFRP tensile face. It is shown that positive hybrid effects exist for the flexural strengths of most of the hybrid configurations. The hybrid effect is noted to be more obvious when the hybrid ratio is small, which may be attributed to the relative position of the GFRP layer(s) with respect to the neutral plane. In contrast to this, flexural modulus seems to obey the rule of mixtures equation.

  17. Restorasi Resin Komposit dengan Pasak Fiber Reinforced Composite untuk Perbaikan Gigi Insisivus Sentralis Maksila Pasca Trauma

    Directory of Open Access Journals (Sweden)

    Mella Synthya Dewi

    2011-06-01

    Full Text Available Latar belakang. Trauma pada gigi dapat menyebabkan injuri pulpa dengan atau tanpa kerusakan mahkota atau akar. Pulpektomi menjadi pilihan perawatan pada fraktur mahkota yang membutuhkan restorasi kompleks. Gigi pasca perawatan saluran akar biasanya telah kehilangan struktur jaringan keras yang cukup banyak sehingga membutuhkan retensi intrakanal berupa pasak untuk mendukung restorasi akhir. Pasak Fiber Reinforced Composite (FRG memiliki flexure dan fatigue strength yang lebih besar, modulus elastisitas yang mendekati dentin, kemampuan untuk membentuk monoblok (kompleks akar-pasak dalam saluran akar, dan meningkatkan estetik jika dibandingkan dengan pasak logam. Resin komposit memiliki warna dan translusensi yang menyerupai dentin dan email sehingga mampu menghasilkan estetik yang baik pada gigi anterior. Tujuan. Melaporkan restorasi resin komposit dengan pasak FRG untuk memperbaiki gigi insisivus sentralis maksila yang mengalami fraktur mahkota kompleks pasca trauma. Kasus dan penanganan. Perempuan 20 tahun, gigi insisivus sentralis kanan dan kiri maksila mengalami Fraktur Ellis klas III akibat kecelakaan. Gigi 11 pulpitis ireversibel dan gigi 21 nekrosis pulpa. Kedua gigi malposisi. Dilakukan pulpektomi atau perawatan saluran akar multi kunjungan. Resin komposit dengan pasak FRG customized digunakan sebagai restorasi akhir. Kesimpulan. Restorasi resin komposit dengan pasak FRG customized memberikan hasil yang memuaskan secara estetik dan fungsional untuk merestorasi gigi insisivus sentralis pasca trauma dan perawatan saluran akar.

  18. Material characterization of several resin systems for high temperature carbon fiber reinforced composites

    Science.gov (United States)

    Yoon, Sung Ho; Oh, Jin Oh; Choi, Dong Hyun; Lee, Sang Woo

    2012-04-01

    Material characterization of several resin systems for high temperature carbon fiber reinforced composites was performed through a series of the tensile test, the dynamic mechanical analysis (DMA) test, and the strand test. The modified tensile specimens and the DMA specimens were used to evaluate the tensile and thermal analysis properties of resin systems. The strand specimens were used to evaluate the tensile properties and load transfer efficiencies of the specimens. Four types of resin systems were considered. One was a conventional resin system currently used for filament wound structures and other three were high temperature resin systems. According to the tensile and DMA test results, the tensile modulus decreases slightly and the tensile strength decreases rapidly until the temperature reaches glass transition temperature. The tensile modulus and tensile strength are almost negligible above glass transition temperature. The tensile modulus obtained from the tensile test is consistent with that from the DMA test at different temperatures. From the strand test results, considering, the load transfer efficiency is found to be around 87 to 90 % of the tensile strength of T800H-12K carbon fibers for all resin systems except the specimen with the Type 2. Finally we found that the Type 4 is the best candidate for high temperature resin system applicable to filament wound structures in the view of the glass transition temperature as well as the tensile properties.

  19. Fiber-reinforced composite analysis using optical coherence tomography after mechanical and thermal cycling

    Science.gov (United States)

    Kyotoku, B. B. C.; Braz, A. K. S.; Braz, R.; Gomes, A. S. L.

    2007-02-01

    Fiber-reinforced composites are new materials which have been used for a variety of dental applications, including tooth splinting, replacement of missing teeth, treatment of dental emergencies, reinforcement of resin provisional fixed prosthodontic restorations, orthodontic retention, and other clinical applications. Different fiber types are available, but little clinical information has been disseminated. The traditional microscopy investigation, most commonly used to study this material, is a destructive technique, which requires specimen sectioning and are essentially surface measurements. On the basis of these considerations, the aim of this research is to analyze the interior of a dental sample reinforced with fiber after a mechanical and thermal cycling to emulate oral conditions using optical coherence tomography (OCT). The device we are using is a home built Fourier domain OCT working at 800 nm with 6 μm resolution. The results are compared with microscopy images to validate OCT as a working method. In long term, fractures allow bacterial invasion provoking plaque and calculus formation that can cause caries and periodontal disease. Therefore, non invasive imaging of the bridge fiber enables the possibility of periodic clinical evaluation to ensure the patient health. Furthermore, OCT images can provide a powerful method for quantitative analysis of crack propagation, and can potentially be used for in vivo assessment.

  20. Fracture Strength and Bending of Fiber-Reinforced Composites and Metal Frameworks in Fixed Partial Dentures

    Directory of Open Access Journals (Sweden)

    M. Sadeghi

    2008-09-01

    Full Text Available Objective: This in vitro study evaluated the fracture strength and bending amount of twotypes of fiber reinforced composite (FRC and cast metal frameworks used for fabrication of inlay fixed partial dentures (IFPDs.Materials and Methods: Seventy-two extracted first maxillary premolars and molars (36 each were embedded in acrylic resin to represent a missing of second maxillary premolar. FRC IFPDs were fabricated using Stick and Fiber-Braid fiber bundles and IFPDs using cast metal alloy (12 for each group. The specimens were stored for 2 weeks at 37°C(SD=1 in distilled water, thermocycled (5-55°C, x 2500 and statically loaded to fracture. The initial bending prior to fracture was evaluated. The data were analyzed using paired t-test and ANOVA test.Results: The fracture strength was significantly higher in the FRC groups (P<0.05; also, the fracture strength was significantly higher in Stick group than Fiber-Braid group (P<0.05. The amount of bending was significantly greater in the FRC groups (P<0.05. The amount of difference in bending between the two groups of FRC was not statistically significant.Conclusion: Within the limits of this in vitrostudy, the results suggest that the FRC IFPDs can be used as a conservative, esthetic alternative to the IFPDs with cast metal frameworks. The results of this study should be confirmed by long-term clinical investigations.

  1. Polyethylene fiber-reinforced composite resin used as a short post in severely decayed primary anterior teeth: a case report.

    Science.gov (United States)

    Bayrak, Sule; Tunc, Emine Sen; Tuloglu, Nuray

    2009-05-01

    The case report presented here is of a 4-year-old girl with severely decayed maxillary anterior teeth. After root canal treatment, the primary maxillary central and lateral incisors were reinforced using polyethylene fiber-reinforced composite resin short posts and restored using celluloid strip crowns. The technique described here offers a simple and effective method for restoring severely decayed primary anterior teeth that reestablishes function, shape, and esthetics.

  2. Provisional anterior tooth replacement using nonimpregnated fiber and fiber-reinforced composite resin materials: a clinical report.

    Science.gov (United States)

    Chan, Daniel C N; Giannini, Marcelo; De Goes, Mario Fernando

    2006-05-01

    The loss of anterior teeth is often a serious esthetic concern. While conventional fixed partial dentures and implant-supported restorations may be the treatments of choice, nonimpregnated fibers (NFs) and fiber-reinforced composite (FRC) resins offer a conservative alternative for improving esthetics. This article describes 2 clinical situations in which NF glass ribbon and FRC were successfully used to provisionally restore anterior edentulous areas in an esthetic, functional, and timely manner.

  3. In vitro evaluation of veneering composites and fibers on the color of fiber-reinforced composite restorations.

    Directory of Open Access Journals (Sweden)

    Masoomeh Hasani Tabatabaei

    2014-08-01

    Full Text Available Color match between fiber-reinforced composite (FRC restorations and teeth is an imperative factor in esthetic dentistry. The purpose of this study is to evaluate the influence of veneering composites and fibers on the color change of FRC restorations.Glass and polyethylene fibers were used to reinforce a direct microhybrid composite (Z250, 3M ESPE and a microfilled composite (Gradia Indirect, GC. There were eight experimental groups (n=5 disks per group. Four groups were used as the controls (non-FRC control and the others were used as experimental groups. CIELAB parameters (L*, a* and b* of specimens were evaluated against a white background using a spectrophotometer to assess the color change. The color difference (ΔE* and color coordinates were (L*, a* and b* analyzed by two-way ANOVA and Tukey's test.Both types of composite and fiber influenced the color parameters (ΔL*, Δa*. The incorporation of fibers into the composite in the experimental groups made them darker than the control groups, except in the Gradia Indirect+ glass fibers group. Δb* is affected by types of fibers only in direct fiber reinforced composite. No statistically significant differences were recognized in ΔE* among the groups (p>0.05.The findings of the present study suggest that the tested FRC restorations exhibited no difference in color in comparison with non-FRC restoration. Hence, the types of veneering composites and fibers did not influence the color change (ΔE* of FRC restorations.

  4. An Investigation of Stimulating the Autoclave Curing Process of Resin Matrix/Fiber Reinforced Composite Material,Ⅰ: Process model

    Institute of Scientific and Technical Information of China (English)

    2003-01-01

    A mathematical model is made which describes the curing process of composites constructed from continuous fiber-reinforced, thermosetting resin matrix prepreg materials, and the consolidation of the composite is developed. The model provides the variation of temperature distribution, the cure reaction process in the resin, the resin flow and fibers stress inside the composite, and the void variation and the residual stress distribution. It can be used to illustrate the mechanism of curing process and optimize the cure cycle of composite material in order to ensure the quality of a product.

  5. Mechanical interaction of Engineered Cementitious Composite (ECC) reinforced with Fiber Reinforced Polymer (FRP) rebar in tensile loading

    DEFF Research Database (Denmark)

    Lárusson, Lárus Helgi; Fischer, Gregor; Jönsson, Jeppe

    2010-01-01

    This paper introduces a preliminary study of the composite interaction of Engineered Cementitious Composite (ECC), reinforced with Glass Fiber Reinforced Polymer (GFRP) rebar. The main topic of this paper will focus on the interaction of the two materials (ECC and GFRP) during axial loading......, particularly in post cracking phase of the concrete matrix. The experimental program carried out in this study examined composite behavior under monotonic and cyclic loading of the specimens in the elastic and inelastic deformation phases. The stiffness development of the composite during loading was evaluated...

  6. The correlation of low-velocity impact resistance of graphite-fiber-reinforced composites with matrix properties

    Science.gov (United States)

    Bowles, K. J.

    1986-01-01

    Summarized are basic studies that were conducted to correlate the impact resistance of graphite-fiber-reinforced composites with polymer matrix properties. Three crosslinked epoxy resins and a linear polysulfone were selected as composite matrices. As a group, these resins possess a significantly large range of mechanical properties. The mechanical properties of the resins and their respective composites were measured. Neat resin specimens and unidirectional and crossply composite specimens were impact tested with an instrumented dropweight tester. Impact resistances of the specimens were assessed on the basis of loading capability, energy absorption, and extent of damage.

  7. Effects of matrix porosity on the mechanical properties of fiber-reinforced oxide composites

    Science.gov (United States)

    Mattoni, Michael Anthony

    Damage tolerance in fiber-reinforced ceramic matrix composites can be achieved through weak bonding between fibers and matrix by the use of fine-scale porosity within the matrix. The effects of matrix porosity on the mechanical properties of porous-matrix, oxide composites are investigated. Porosity is systematically varied through impregnation and pyrolysis of a ceramic precursor solution, and mechanical tests are performed to identify the role of the matrix in both fiber- and matrix-dominated loadings. Two families of composites are examined in this study. The first family possesses a non-uniform porosity distribution due to precursor segregation during drying. Mechanical testing demonstrates a loss of damage tolerance and tensile strength along the fiber direction as the porosity is reduced. Concurrently some improvements in interlaminar shear strength are observed. Building upon this investigation, segregation is eliminated in subsequent studies through use of a gelation step following precursor impregnation. In this family, moderate additions of precursor-derived alumina to the matrix improve the in-plane shear and tensile strength. Concurrently, a significant increase in notch sensitivity is observed. Two theoretical frameworks are developed for the notched strength of ceramic matrix composites. The first considers composites that exhibit rising fracture resistance and is based upon established concepts of crack stability under stress-controlled loadings. The form of the resistance curve assumes that the crack tip inelastic zone is small in relation to the geometric and bridging length scales, making this framework applicable to relatively dense porous matrix composites. The results reveal salient trends in strength with notch length and specimen geometry. An assessment of the theory is made through comparison with experimental measurements. The second framework developed for notch-sensitivity explicitly accounts for large-scale inelasticity, allowing

  8. Laser-Generated Lamb Waves Propagation in Multilayered Plates Composed of Viscoelastic Fiber-reinforced Composite Materials

    Science.gov (United States)

    Sun, Hong-xiang; Zhang, Shu-yi; Yuan, Shou-qi; Guan, Yi-jun; Ge, Yong

    2016-07-01

    The propagation characteristics of laser-generated Lamb waves in multilayered fiber-reinforced composite plates with different fiber orientations and number of layers have been investigated quantitatively. Considering the viscoelasticity of the composite materials, we have set up finite element models for simulating the laser-generated Lamb waves in two types of the multilayered composite plates. In the first type, different fiber orientations are adopted. In the second one, different number of layers are considered. The results illustrate the occurrence of attenuation and dispersion, which is induced by the viscoelasticity and multilayer structure, respectively.

  9. Scarf Repair of Composite Laminates

    Directory of Open Access Journals (Sweden)

    Xie Zonghong

    2016-01-01

    Full Text Available The use of composite materials, such as carbon-fiber reinforced plastic (CFRP composites, aero-structures has led to an increased need of advanced assembly joining and repair technologies. Adhesive bonded repairs as an alternative to recover full or part of initial strength were investigated. Tests were conducted with the objective of evaluating the effectiveness of techniques used for repairing damage fiber reinforced laminated composites. Failure loads and failure modes were generated and compared with the following parameters: scarf angles, roughness of grind tool and number of external plies. Results showed that scarf angle was the critical parameter and the largest tensile strength was observed with the smallest scarf angle. Besides, the use of external plies at the outer surface could not increase the repairs efficiency for large scarf angle. Preparing the repair surfaces by sanding them with a sander ranging from 60 to 100 grit number had significant effect on the failure load. These results allowed the proposal of design principles for repairing CFRP structures.

  10. Tailoring of fiber-reinforced cementitious composites (FRCC) for flexural strength and reliability

    Science.gov (United States)

    Obla, Karthikeyan Hariya

    Bending is the most common form of loading for many construction elements. The bending strength or Modulus of Rupture (MOR) and flexural ductility are therefore critical properties particularly for those elements which are not reinforced by rebars. Such elements include highway barriers, certain wall panels, thin sheet elements and small diameter pipes. The tensile and bending strengths of concrete are very low. In addition, as a brittle material, concrete also demonstrates a large variability in bending strength. A large variability in MOR leads to inefficient use of the material since the design strength has to be close to the lower bound of the material's strength distribution. The potential of fiber in improving MOR is well recognized in fiber reinforced concrete. The use of fiber to enhance material reliability is much less studied. This thesis addresses both aspects employing a combination of theoretical and experimental treatments. Research findings are reported as Part I and Part II of this thesis. Carbon fibers are increasingly attractive for reinforcing cementitious composites. They can be manufactured to yield a wide range in modulus and strength. Carbon fibers are non-corrosive, and fire and alkali. In addition, the price of pitch based carbon fibers are dropping rapidly to make them economically viable for the building and construction industries. In Part I of the thesis, a study on the optimization of the bending strength of carbon FRCC using a fracture based flexural model that links the fiber, interface, and matrix micro-parameters to composite bending strength is presented. Carbon fiber, interface and matrix parameters were tailored to yield optimal properties such as high MOR and ductility. Four point bend tests were conducted on CFRCCs to confirm the findings. Some problems specially affecting carbon FRCCs such as fiber breakage during mixing were also studied and its effects on composite uniaxial tensile properties analyzed by developing new

  11. Self-sealing of thermal fatigue and mechanical damage in fiber-reinforced composite materials

    Science.gov (United States)

    Moll, Jericho L.

    Fiber reinforced composite tanks provide a promising method of storage for liquid oxygen and hydrogen for aerospace applications. The inherent thermal fatigue of these vessels leads to the formation of microcracks, which allow gas phase leakage across the tank walls. In this dissertation, self-healing functionality is imparted to a structural composite to effectively seal microcracks induced by both mechanical and thermal loading cycles. Two different microencapsulated healing chemistries are investigated in woven glass fiber/epoxy and uni-weave carbon fiber/epoxy composites. Self-healing of mechanically induced damage was first studied in a room temperature cured plain weave E-glass/epoxy composite with encapsulated dicyclopentadiene (DCPD) monomer and wax protected Grubbs' catalyst healing components. A controlled amount of microcracking was introduced through cyclic indentation of opposing surfaces of the composite. The resulting damage zone was proportional to the indentation load. Healing was assessed through the use of a pressure cell apparatus to detect nitrogen flow through the thickness direction of the damaged composite. Successful healing resulted in a perfect seal, with no measurable gas flow. The effect of DCPD microcapsule size (51 microm and 18 microm) and concentration (0--12.2 wt%) on the self-sealing ability was investigated. Composite specimens with 6.5 wt% 51 microm capsules sealed 67% of the time, compared to 13% for the control panels without healing components. A thermally stable, dual microcapsule healing chemistry comprised of silanol terminated poly(dimethyl siloxane) plus a crosslinking agent and a tin catalyst was employed to allow higher composite processing temperatures. The microcapsules were incorporated into a satin weave E-glass fiber/epoxy composite processed at 120°C to yield a glass transition temperature of 127°C. Self-sealing ability after mechanical damage was assessed for different microcapsule sizees (25 microm and 42

  12. Resin characterization in cured graphite fiber reinforced composites using diffuse reflectance-FTIR. [Fourier transform infrared spectroscopy

    Science.gov (United States)

    Young, P. R.; Stein, B. A.; Chang, A. C.

    1983-01-01

    The feasibility of using diffuse reflectance in combination with Fourier transform infrared spectroscopy to obtain information on cured graphite fiber reinforced polymeric matrix resin composites was investigated. Several graphite/epoxy, polysulfone, and polyimide composites exposed to thermal or radiation environments were examined. An experimental polyimide-sulfone adhesive tape was also studied during processing. In each case, significant changes in resin molecular structure was observed due to environmental exposure. These changes in molecular structure were correlated with previously observed changes in material properties providing new insights into material behavior.

  13. Investigation of degradation products produced by recycling the solvent during chemical degradation of fiber-reinforced composites

    DEFF Research Database (Denmark)

    Ucar, Hülya; Simonsen, Morten Enggrob; Søgaard, Erik Gydesen

    2017-01-01

    of solvent consumption by 88%. It was found that the recycled solvent became increasingly more concentrated with degradation products from the epoxy resin and compounds produced by acetone aldol reactions. These degradation products promoted and enhanced the degradation of the composite. Among the compounds...... of the process. In this study, acetone has been used as the organic solvent. To increase the sustainability of the process, the solvent was recycled in eight consecutive batches using new glass fiber-reinforced composites in each recycling. No additional amount of acetone was added, resulting in a reduction...

  14. The use of fiber-reinforced scaffolds cocultured with Schwann cells and vascular endothelial cells to repair rabbit sciatic nerve defect with vascularization.

    Science.gov (United States)

    Gao, Hongyang; You, Yang; Zhang, Guoping; Zhao, Feng; Sha, Ziyi; Shen, Yong

    2013-01-01

    To explore the feasibility of biodegradable fiber-reinforced 3D scaffolds with satisfactory mechanical properties for the repair of long-distance sciatic nerve defect in rabbits and effects of vascularized graft in early stage on the recovery of neurological function, Schwann cells and vascular endothelial cells were cocultured in the fiber-reinforced 3D scaffolds. Experiment group which used prevascularized nerve complex for the repair of sciatic nerve defect and control group which only cultured with Schwann cells were set. The animals in both groups underwent electromyography to show the status of the neurological function recovery at 4, 8, and 16 weeks after the surgery. Sciatic nerve regeneration and myelination were observed under the light microscope and electron microscope. Myelin sheath thickness, axonal diameter, and number of myelinated nerve fiber were quantitatively analyzed using image analysis system. The recovery of foot ulcer, the velocity of nerve conduction, the number of regenerating nerve fiber, and the recovery of ultrastructure were increased in the experimental group than those in the control group. Prevascularized tissue engineered fiber-reinforced 3D scaffolds for the repair of sciatic nerve defects in rabbits can effectively promote the recovery of neurological function.

  15. The Use of Fiber-Reinforced Scaffolds Cocultured with Schwann Cells and Vascular Endothelial Cells to Repair Rabbit Sciatic Nerve Defect with Vascularization

    Directory of Open Access Journals (Sweden)

    Hongyang Gao

    2013-01-01

    Full Text Available To explore the feasibility of biodegradable fiber-reinforced 3D scaffolds with satisfactory mechanical properties for the repair of long-distance sciatic nerve defect in rabbits and effects of vascularized graft in early stage on the recovery of neurological function, Schwann cells and vascular endothelial cells were cocultured in the fiber-reinforced 3D scaffolds. Experiment group which used prevascularized nerve complex for the repair of sciatic nerve defect and control group which only cultured with Schwann cells were set. The animals in both groups underwent electromyography to show the status of the neurological function recovery at 4, 8, and 16 weeks after the surgery. Sciatic nerve regeneration and myelination were observed under the light microscope and electron microscope. Myelin sheath thickness, axonal diameter, and number of myelinated nerve fiber were quantitatively analyzed using image analysis system. The recovery of foot ulcer, the velocity of nerve conduction, the number of regenerating nerve fiber, and the recovery of ultrastructure were increased in the experimental group than those in the control group. Prevascularized tissue engineered fiber-reinforced 3D scaffolds for the repair of sciatic nerve defects in rabbits can effectively promote the recovery of neurological function.

  16. Stiffness and Strength of Fiber Reinforced Polymer Composite Bridge Deck Systems

    OpenAIRE

    2002-01-01

    This research investigates two principal characteristics that are of primary importance in Fiber Reinforced Polymer (FRP) bridge deck applications: STIFFNESS and STRENGTH. The research was undertaken by investigating the stiffness and strength characteristics of the multi-cellular FRP bridge deck systems consisting of pultruded FRP shapes. A systematic analysis procedure was developed for the stiffness analysis of multi-cellular FRP deck systems. This procedure uses the Method of Elasti...

  17. Bonding performance and interfacial characteristics of short fiber-reinforced resin composite in comparison with other composite restoratives.

    Science.gov (United States)

    Tsujimoto, Akimasa; Barkmeier, Wayne W; Takamizawa, Toshiki; Latta, Mark A; Miyazaki, Masashi

    2016-06-01

    The purpose of this study was to investigate the shear bond strength (SBS) and surface free-energy (SFE) of short fiber-reinforced resin composite (SFRC), using different adhesive systems, in comparison with other composite restoratives. The resin composites used were everX Posterior (EP), Clearfil AP-X (CA), and Filtek Supreme Ultra Universal Restorative (FS). The adhesive systems used were Scotchbond Multi-Purpose (SM), Clearfil SE Bond (CS), and G-Premio Bond (GB). Resin composite was bonded to dentin, and SBS was determined after 24 h of storage in distilled water and after 10,000 thermal cycles (TCs). The SFEs of the resin composites and the adhesives were determined by measuring the contact angles of three test liquids. The SFE values and SFE characteristics were not influenced by the type of resin composite, but were influenced by the type of adhesive system. The results of this study suggest that the bonding performance and interfacial characteristics of SFRC are the same as for other composite restoratives, but that these parameters are affected by the type of adhesive system. The bonding performance of SFRC was enhanced by thermal cycling in a manner similar to that for other composite restoratives.

  18. Recovery of microfields in fiber-reinforced composite materials: Principles and limitations

    Science.gov (United States)

    Ritchey, Andrew J.

    A detailed investigation of the limitations and errors induced by modeling a composite layer composed of straight carbon fibers embedded in an epoxy matrix as an homogenous layer with Cauchy effective moduli is performed. Specifically, the material system studied has IM7 carbon fibers arranged in a square array and bonded together with 8552 epoxy resin (IM7/8552). The finite element method is used to study the effect of free surfaces on the local elastic fields in 0°, 45° and 90° laminae, in which as many as 256 individual fibers are modeled. Through these analyses, it is shown that a micro-boundary layer, analogous to the macro-boundary layer observed in composite laminates, is developed at the microlevel. Additionally, [0/90]s and [90/0]s laminates are studied to investigate the joint action of the macro- and micro-boundary layers. Unless otherwise noted, fiber volume fractions of Vƒ=0.20 and Vƒ=0.65 are selected and the domains are subjected to uniform axial extension. Although this study is done for a highly idealized geometry (i.e. with a single material system and under a simple loading condition) the principles of periodicity, symmetry and antisymmetry used to efficiently perform a direct numerical simulation with a large number of fiber inclusions is general, and can be applied to more complicated geometries and boundary conditions. The purpose of the current work is to be the first step in a building block approach to understanding the interaction of multiple scales in fiber-reinforced composites through direct numerical simulations. The main part of the current manuscript focuses on the characterization of a micro-boundary layer that develops in fiber reinforced composite layers. This phenomena results from the changing constraints on the constituent phases as a result of discontinuities, such as free surfaces or ply interfaces. The effect is most pronounced in laminae that have a fiber termination intersecting a free surface, and appears to be

  19. Stiffness and strength of fiber reinforced polymer composite bridge deck systems

    Science.gov (United States)

    Zhou, Aixi

    This research investigates two principal characteristics that are of primary importance in Fiber Reinforced Polymer (FRP) bridge deck applications: STIFFNESS and STRENGTH. The research was undertaken by investigating the stiffness and strength characteristics of the multi-cellular FRP bridge deck systems consisting of pultruded FRP shapes. A systematic analysis procedure was developed for the stiffness analysis of multi-cellular FRP deck systems. This procedure uses the Method of Elastic Equivalence to model the cellular deck as an equivalent orthotropic plate. The procedure provides a practical method to predict the equivalent orthotropic plate properties of cellular FRP decks. Analytical solutions for the bending analysis of single span decks were developed using classical laminated plate theory. The analysis procedures can be extended to analyze continuous FRP decks. It can also be further developed using higher order plate theories. Several failure modes of the cellular FRP deck systems were recorded and analyzed through laboratory and field tests and Finite Element Analysis (FEA). Two schemes of loading patches were used in the laboratory test: a steel patch made according to the ASSHTO's bridge testing specifications; and a tire patch made from a real truck tire reinforced with silicon rubber. The tire patch was specially designed to simulate service loading conditions by modifying real contact loading from a tire. Our research shows that the effects of the stiffness and contact conditions of loading patches are significant in the stiffness and strength testing of FRP decks. Due to the localization of load, a simulated tire patch yields larger deflection than the steel patch under the same loading level. The tire patch produces significantly different failure compared to the steel patch: a local bending mode with less damage for the tire patch; and a local punching-shear mode for the steel patch. A deck failure function method is proposed for predicting the

  20. Thermal residual stresses and stress distributions under tensile and compressive loadings of short fiber reinforced metal matrix composites

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    The thermal residual stresses and the stress distributions of short fiber reinforced metal matrix composite under tensile and compressive loadings were studied using large strain axisymmetric elasto-plastic finite element method. It is demonstrated that the thermal residual stresses can result in asymmetrical stress distributions and matrix plasticity. The thermal residual stresses decrease the stress transfer in tension and enhance the stress transfer in compression. The fiber volume fraction has more important effects on the thermal residual stresses and the stress distributions under tensile and compressive loadings than the fiber aspect ratio and the fiber end distance.

  1. Effect of TiO2 deposition on the mechanical properties of a carbon-fiber-reinforced bismaleimide composite

    Science.gov (United States)

    Di, Jang; Chunhua, Cao; Jie, Wu

    2013-07-01

    In order to improve the mechanical properties of carbon-fiber-reinforced bismaleimide (CF/BMI) composites, TiO2 was deposited on the carbon fibers. The short-beam shear and mechanical properties of the composites were investigated. Both raw and TiO2-coated CFs were utilized for their fabrication. The tensile strength of the composites, both with raw and TiO2-coated fibers, grew with increasing filler content. The tensile strength of the CF/BMI composites with treated fibers, at all mixing ratios, was found to be by 18% higher than that of the composites with untreated ones. The surface morphologies of fracture surfaces of the composites were recorded using the scanning electron microscopy (SEM) to gain information about the interfacial fiber-matrix adhesion in the composites.

  2. Fiber-Reinforced Polymer Composites in Bridges: A State-of-the-Art Report

    Science.gov (United States)

    2005-05-01

    address FRP composite topics related to concrete such as research needs, repair, rebar, prestressing, and stay-in-place structural formwork . Several...two vehicular lanes, two bike lanes, a pedestrian walkway, and a utility service tunnel . As of 2005 the bridge had not been constructed. 27

  3. A note on the effect of the fiber curvature on the micromechanical behavior of natural fiber reinforced thermoplastic composites

    Directory of Open Access Journals (Sweden)

    M. A. Escalante-Solis

    2015-12-01

    Full Text Available To better understand the role of the fiber curvature on the tensile properties of short-natural-fiber reinforced composites, a photoelastic model and a finite element analysis were performed in a well characterized henequen fiber-high density polyethylene composite material. It was hypothesized that the angle of orientation of the inclusion and the principal material orientation with respect to the applied load was very important in the reinforcement mechanics. From the photoelastic and finite element analysis it was found that the stress distribution around the fiber inclusion was different on the concave side from that observed on the convex side and an efficient length of stress transfer was estimated to be approximately equal to one third the average fiber length. This approach was used to predict the short-natural-fiber reinforced composite mechanical properties using probabilistic functions modifications of the rule of mixtures models developed by Fukuda-Chow and the Fukuda-Kawata. Recognizing the inherent flexibility that curves the natural fibers during processing, the consideration of a length of one third of the average length l should improve the accuracy of the calculations of the mechanical properties using theoretical models.

  4. Fracture resistance, two point bending strength and morphological characteristics of pulpless teeth restored with fiber-reinforced composite posts

    Directory of Open Access Journals (Sweden)

    Alfredo Tibúrcio Nunes Pires

    2012-09-01

    Full Text Available Introduction: Fiber-reinforced composite posts (FRC posts have been used for tooth reinforcement after endodontic treatment. The mechanical characteristics of FRC posts can influence the clinical prognostic. Objective: The aim of this study was to evaluate the flexural strength and fracture resistance of commercially available FRC posts Material and methods: Fourteen human single-rooted premolars with completely formed apices were selected and received endodontic treatment. The specimens were divided into two groups related to the post system: i Group A – cylindrical-conical fiber-reinforced post (White post DC, FGM, and ii group B – conical fiber-reinforced post (EXACTO, Angelus. The fracture resistance was evaluated and two point bending tests were carried out. The glass fiber characteristics and the tag penetration of the luting material into the radicular dentin structure were evaluated through scanning electronic microscopy in an illustrative way. One-way ANOVA and Tukey’s HSD test (α = 0.05 were applied. Results: The values obtained for fracture resistance and two point bending test were, respectively, 399.29 N and 109.5 N for group A, and 386.25 N and 119.5 N for group B. No significant differences in strength values among the groups were found. Conclusion: There were no significant statistical differences between the two post groups regarding to fracture strength and two point bending strength. It can be concluded that the posts selected for this study performed satisfactorily in terms of mechanical properties so that they can be used for tooth reinforcement after endodontic treatment.

  5. A facile approach to make high performance nano-fiber reinforced composite separator for lithium ion batteries

    Science.gov (United States)

    Huang, Xiaosong

    2016-08-01

    The separator is a porous membrane located between the negative and the positive electrodes. In this work, a nano-fiber reinforced composite separator was developed. Compared with the commercial polyolefin separator, the composite separator showed superior (a) dimensional stability at elevated temperatures relative to conventional separators and (b) wettability by the liquid electrolyte. After being saturated with a commercial LiPF6-ethylene carbonate-dimethyl carbonate electrolyte, the composite separator enabled a high effective ionic conductivity (σeff) of 1.25 mS/cm. A stable cycle performance and an improved rate capability have been observed in the coin cells with the composite separator. This initial study shows that this type of composite membranes can be a promising alternative separator for lithium ion batteries.

  6. Effects of precoating and calcination on microstructure of 3D silica fiber reinforced silicon nitride based composites

    Institute of Scientific and Technical Information of China (English)

    QI Gong-jin; ZHANG Chang-rui; HU Hai-feng

    2006-01-01

    Three-dimensional silica fiber reinforced silicon nitride based composites were fabricated by preceramic polymer infiltration and pyrolysis method using perhydropolysilazane as a precursor. The effects of precoating and high temperature calcination on the microstructures of the composites were investigated by scanning electron microscopy. For the composite without a precoating, the fracture surface is plain, and the fiber/matrix interfaces become very unclear after calcination at 1 600 ℃ due to intense interfacial reactions. The composite with a precoating shows tough fracture surface with distinct fiber pull-outs, and the fiber/matrix interfaces are still clear after calcination at 1 600 ℃. It is the appropriate precoating process that contributes to the good interfacial microstructures for the composite.

  7. Recycling high-performance carbon fiber reinforced polymer composites using sub-critical and supercritical water

    Science.gov (United States)

    Knight, Chase C.

    Carbon fiber reinforced plastics (CFRP) are composite materials that consist of carbon fibers embedded in a polymer matrix, a combination that yields materials with properties exceeding the individual properties of each component. CFRP have several advantages over metals: they offer superior strength to weight ratios and superior resistance to corrosion and chemical attack. These advantages, along with continuing improvement in manufacturing processes, have resulted in rapid growth in the number of CFRP products and applications especially in the aerospace/aviation, wind energy, automotive, and sporting goods industries. Due to theses well-documented benefits and advancements in manufacturing capabilities, CFRP will continue to replace traditional materials of construction throughout several industries. However, some of the same properties that make CFRP outstanding materials also pose a major problem once these materials reach the end of service life. They become difficult to recycle. With composite consumption in North America growing by almost 5 times the rate of the US GDP in 2012, this lack of recyclability is a growing concern. As consumption increases, more waste will inevitably be generated. Current composite recycling technologies include mechanical recycling, thermal processing, and chemical processing. The major challenge of CFRP recycling is the ability to recover materials of high-value and preserve their properties. To this end, the most suitable technology is chemical processing, where the polymer matrix can be broken down and removed from the fiber, with limited damage to the fibers. This can be achieved using high concentration acids, but such a process is undesirable due to the toxicity of such materials. A viable alternative to acid is water in the sub-critical and supercritical region. Under these conditions, the behavior of this abundant and most environmentally friendly solvent resembles that of an organic compound, facilitating the breakdown

  8. Application of headed studs in steel fiber reinforced cementitious composite slab of steel beam-column connection

    Science.gov (United States)

    Yao, Cui; Nakashima, Masayoshi

    2012-03-01

    Steel fiber reinforced cementitous composites (SFRCC) is a promising material with high strength in both compression and tension compared with normal concrete. The ductility is also greatly improved because of 6% volume portion of straight steel fibers. A steel beam-column connection with Steel fiber reinforced cementitous composites (SFRCC) slab diaphragms is proposed to overcome the damage caused by the weld. The push-out test results suggested that the application of SFRCC promises larger shear forces transferred through headed studs allocated in a small area in the slab. Finite element models were developed to simulate the behavior of headed studs. The failure mechanism of the grouped arrangement is further discussed based on a series of parametric analysis. In the proposed connection, the SFRCC slab is designed as an exterior diaphragm to transfer the beam flange load to the column face. The headed studs are densely arranged on the beam flange to connect the SFRCC slab diaphragms and steel beams. The seismic performance and failure mechanism of the SFRCC slab diaphragm beam-column connection were investigated based on the cyclic loading test. Beam hinge mechanism was achieved at the end of the SFRCC slab diaphragm by using sufficient studs and appropriate rebars in the SFRCC slab.

  9. Relationship Between Hysteresis Dissipated Energy and Temperature Rising in Fiber-Reinforced Ceramic-Matrix Composites Under Cyclic Loading

    Science.gov (United States)

    Longbiao, Li

    2016-06-01

    In this paper, the relationship between hysteresis dissipated energy and temperature rising of the external surface in fiber-reinforced ceramic-matrix composites (CMCs) during the application of cyclic loading has been analyzed. The temperature rise, which is caused by frictional slip of fibers within the composite, is related to the hysteresis dissipated energy. Based on the fatigue hysteresis theories considering fibers failure, the hysteresis dissipated energy and a hysteresis dissipated energy-based damage parameter changing with the increase of cycle number have been investigated. The relationship between the hysteresis dissipated energy, a hysteresis dissipated energy-based damage parameter and a temperature rise-based damage parameter have been established. The experimental temperature rise-based damage parameter of unidirectional, cross-ply and 2D woven CMCs corresponding to different fatigue peak stresses and cycle numbers have been predicted. It was found that the temperature rise-based parameter can be used to monitor the fatigue damage evolution and predict the fatigue life of fiber-reinforced CMCs.

  10. Self-Healing Capability of Fiber-Reinforced Cementitious Composites for Recovery of Watertightness and Mechanical Properties

    Directory of Open Access Journals (Sweden)

    Tomoya Nishiwaki

    2014-03-01

    Full Text Available Various types of fiber reinforced cementitious composites (FRCCs were experimentally studied to evaluate their self-healing capabilities regarding their watertightness and mechanical properties. Cracks were induced in the FRCC specimens during a tensile loading test, and the specimens were then immersed in static water for self-healing. By water permeability and reloading tests, it was determined that the FRCCs containing synthetic fiber and cracks of width within a certain range (<0.1 mm exhibited good self-healing capabilities regarding their watertightness. Particularly, the high polarity of the synthetic fiber (polyvinyl alcohol (PVA series and hybrid fiber reinforcing (polyethylene (PE and steel code (SC series showed high recovery ratio. Moreover, these series also showed high potential of self-healing of mechanical properties. It was confirmed that recovery of mechanical property could be obtained only in case when crack width was sufficiently narrow, both the visible surface cracks and the very fine cracks around the bridging of the SC fibers. Recovery of the bond strength by filling of the very fine cracks around the bridging fibers enhanced the recovery of the mechanical property.

  11. UV-Assisted 3D Printing of Glass and Carbon Fiber-Reinforced Dual-Cure Polymer Composites

    Directory of Open Access Journals (Sweden)

    Marta Invernizzi

    2016-07-01

    Full Text Available Glass (GFR and carbon fiber-reinforced (CFR dual-cure polymer composites fabricated by UV-assisted three-dimensional (UV-3D printing are presented. The resin material combines an acrylic-based photocurable resin with a low temperature (140 °C thermally-curable resin system based on bisphenol A diglycidyl ether as base component, an aliphatic anhydride (hexahydro-4-methylphthalic anhydride as hardener and (2,4,6,-tris(dimethylaminomethylphenol as catalyst. A thorough rheological characterization of these formulations allowed us to define their 3D printability window. UV-3D printed macrostructures were successfully demonstrated, giving a clear indication of their potential use in real-life structural applications. Differential scanning calorimetry and dynamic mechanical analysis highlighted the good thermal stability and mechanical properties of the printed parts. In addition, uniaxial tensile tests were used to assess the fiber reinforcing effect on the UV-3D printed objects. Finally, an initial study was conducted on the use of a sizing treatment on carbon fibers to improve the fiber/matrix interfacial adhesion, giving preliminary indications on the potential of this approach to improve the mechanical properties of the 3D printed CFR components.

  12. Cryogenic optical measurements of 12-segment-bonded carbon-fiber-reinforced silicon carbide composite mirror with support mechanism

    Science.gov (United States)

    Kaneda, Hidehiro; Nakagawa, Takao; Onaka, Takashi; Enya, Keigo; Makiuti, Sin'itirou; Takaki, Junji; Haruna, Masaki; Kume, Masami; Ozaki, Tsuyoshi

    2008-03-01

    A 720 mm diameter 12-segment-bonded carbon-fiber-reinforced silicon carbide (C/SiC) composite mirror has been fabricated and tested at cryogenic temperatures. Interferometric measurements show significant cryogenic deformation of the C/SiC composite mirror, which is well reproduced by a model analysis with measured properties of the bonded segments. It is concluded that the deformation is due mostly to variation in coefficients of thermal expansion among segments. In parallel, a 4-degree-of-freedom ball-bearing support mechanism has been developed for cryogenic applications. The C/SiC composite mirror was mounted on an aluminum base plate with the support mechanism and tested again. Cryogenic deformation of the mirror attributed to thermal contraction of the aluminum base plate via the support mechanism is highly reduced by the support, confirming that the newly developed support mechanism is promising for its future application to large-aperture cooled space telescopes.

  13. Synergistic Effects of Temperature and Oxidation on Matrix Cracking in Fiber-Reinforced Ceramic-Matrix Composites

    Science.gov (United States)

    Longbiao, Li

    2017-06-01

    In this paper, the synergistic effects of temperatrue and oxidation on matrix cracking in fiber-reinforced ceramic-matrix composites (CMCs) has been investigated using energy balance approach. The shear-lag model cooperated with damage models, i.e., the interface oxidation model, interface debonding model, fiber strength degradation model and fiber failure model, has been adopted to analyze microstress field in the composite. The relationships between matrix cracking stress, interface debonding and slipping, fiber fracture, oxidation temperatures and time have been established. The effects of fiber volume fraction, interface properties, fiber strength and oxidation temperatures on the evolution of matrix cracking stress versus oxidation time have been analyzed. The matrix cracking stresses of C/SiC composite with strong and weak interface bonding after unstressed oxidation at an elevated temperature of 700 °C in air condition have been predicted for different oxidation time.

  14. The influence of porosity on ultrasound attenuation in carbon fiber reinforced plastic composites using the laser-ultrasound spectroscopy

    Science.gov (United States)

    Karabutov, A. A.; Podymova, N. B.; Belyaev, I. O.

    2013-11-01

    Wideband acoustic spectroscopy with a laser ultrasound source for quantitative analysis of the effect of porosity on the attenuation coefficient of longitudinal acoustic waves in carbon fiber reinforced plastic (CFRP) composite materials was experimentally implemented. The samples under study had different bulk-porosity levels (up to 10%), which were determined using X-ray computer tomography. A resonance ultrasound attenuation peak associated with the one-dimensional periodicity of the layered composite structure was observed for all samples. The absolute value of the resonance-peak maximum and its width depend on the local concentration of microscopic isolated pores and extended delaminations in the sample structure. The obtained empirical relationships between these parameters of the frequency dependence of the ultrasound attenuation coefficient and the type of inhomogeneities and their volume concentration can be used for rapid evaluation of the structural quality of CFRP composites.

  15. Effects of Alkali Treatment and Polyisocyanate Crosslinking on the Mechanical Properties of Kraft Fiber-Reinforced Unsaturated Polyester Composites

    Directory of Open Access Journals (Sweden)

    Zhenhua Gao

    2014-08-01

    Full Text Available The effects of alkali treatment and polyisocyanate crosslinking on the mechanical properties of kraft fiber-reinforced UPE composites were investigated by means of tensile evaluation, SEM analysis, and XRD analysis. The results indicated that the alkali treatment decreased the tensile strength of the prepared composite before aging from 121 MPa to 97 MPa due to the decreased degree of crystallinity of the alkali-treated kraft fiber. Polyisocyanate crosslinking could apparently improve the mechanical properties and stability in terms of a 43% increase of non-aged tensile strength and 52% increase of hydrothermal-aged tensile strength compared with the controlled composite without crosslinking modification, which was attributable to the formation of strong chemical bonding between the interfaces of kraft fiber and polyester.

  16. Design aid for shear strengthening of reinforced concrete T-joints using carbon fiber reinforced plastic composites

    Science.gov (United States)

    Gergely, Ioan

    The research presented in the present work focuses on the shear strengthening of beam column joints using carbon fiber composites, a material considered in seismic retrofit in recent years more than any other new material. These composites, or fiber reinforced polymers, offer huge advantages over structural steel reinforced concrete or timber. A few of these advantages are the superior resistance to corrosion, high stiffness to weight and strength to weight ratios, and the ability to control the material's behavior by selecting the orientation of the fibers. The design and field application research on reinforced concrete cap beam-column joints includes analytical investigations using pushover analysis; design of carbon fiber layout, experimental tests and field applications. Several beam column joints have been tested recently with design variables as the type of composite system, fiber orientation and the width of carbon fiber sheets. The surface preparation has been found to be critical for the bond between concrete and composite material, which is the most important factor in joint shear strengthening. The final goal of this thesis is to develop design aids for retrofitting reinforced concrete beam column joints. Two bridge bents were tested on the Interstate-15 corridor. One bent was tested in the as-is condition. Carbon fiber reinforced plastic composite sheets were used to externally reinforce the second bridge bent. By applying the composite, the displacement ductility has been doubled, and the bent overall lateral load capacity has been increased as well. The finite element model (using DRAIN-2DX) was calibrated to model the actual stiffness of the supports. The results were similar to the experimental findings.

  17. Effect of fabric structure and polymer matrix on flexural strength, interlaminar shear stress, and energy dissipation of glass fiber-reinforced polymer composites

    Science.gov (United States)

    We report the effect of glass fiber structure and the epoxy polymer system on the flexural strength, interlaminar shear stress (ILSS), and energy absorption properties of glass fiber-reinforced polymer (GFRP) composites. Four different GFRP composites were fabricated from two glass fiber textiles of...

  18. Hygrothermal effects on fiber reinforced polyphenylene sulphide composites : humidity uptake and temperature influence on mechanical properties of glass and carbon fiber reinforced polyphenylene sulphide composites

    OpenAIRE

    Suárez Cabrera, Emmanuel

    2011-01-01

    In the ever-continuing quest for greener and cheaper aerospace materials, the Durability Group, part of the Design and Production of Composite Structures Department at the faculty of Aerospace Engineering of the Delft University of Technology is focusing on the use of new thermoplastic composites for aerospace structures. Currently the introduction of Nylon composites in the aerospace industry is being investigated. Nylon as a thermoplastic matrix for fibre reinforced composites can be bought...

  19. Time-Dependent Stress Rupture Strength Degradation of Hi-Nicalon Fiber-Reinforced Silicon Carbide Composites at Intermediate Temperatures

    Science.gov (United States)

    Sullivan, Roy M.

    2016-01-01

    The stress rupture strength of silicon carbide fiber-reinforced silicon carbide composites with a boron nitride fiber coating decreases with time within the intermediate temperature range of 700 to 950 degree Celsius. Various theories have been proposed to explain the cause of the time-dependent stress rupture strength. The objective of this paper is to investigate the relative significance of the various theories for the time-dependent strength of silicon carbide fiber-reinforced silicon carbide composites. This is achieved through the development of a numerically based progressive failure analysis routine and through the application of the routine to simulate the composite stress rupture tests. The progressive failure routine is a time-marching routine with an iterative loop between a probability of fiber survival equation and a force equilibrium equation within each time step. Failure of the composite is assumed to initiate near a matrix crack and the progression of fiber failures occurs by global load sharing. The probability of survival equation is derived from consideration of the strength of ceramic fibers with randomly occurring and slow growing flaws as well as the mechanical interaction between the fibers and matrix near a matrix crack. The force equilibrium equation follows from the global load sharing presumption. The results of progressive failure analyses of the composite tests suggest that the relationship between time and stress-rupture strength is attributed almost entirely to the slow flaw growth within the fibers. Although other mechanisms may be present, they appear to have only a minor influence on the observed time-dependent behavior.

  20. Fracture Resistance of Endodontically Treated Teeth Restored with 2 Different Fiber-reinforced Composite and 2 Conventional Composite Resin Core Buildup Materials: An In Vitro Study.

    Science.gov (United States)

    Eapen, Ashly Mary; Amirtharaj, L Vijay; Sanjeev, Kavitha; Mahalaxmi, Sekar

    2017-09-01

    The purpose of this in vitro study was to comparatively evaluate the fracture resistance of endodontically treated teeth restored with 2 fiber-reinforced composite resins and 2 conventional composite resin core buildup materials. Sixty noncarious unrestored human maxillary premolars were collected, endodontically treated (except group 1, negative control), and randomly divided into 5 groups (n = 10). Group 2 was the positive control. The remaining 40 prepared teeth were restored with various direct core buildup materials as follows: group 3 teeth were restored with dual-cure composite resin, group 4 with posterior composite resin, group 5 with fiber-reinforced composite resin, and group 6 with short fiber-reinforced composite resin. Fracture strength testing was performed using a universal testing machine. The results were statistically analyzed by 1-way analysis of variance and the post hoc Tukey test. Fracture patterns for each sample were also examined under a light microscope to determine the level of fractures. The mean fracture resistance values (in newtons) were obtained as group 1 > group 6 > group 4 > group 3 > group 5 > group 2. Group 6 showed the highest mean fracture resistance value, which was significantly higher than the other experimental groups, and all the fractures occurred at the level of enamel. Within the limitations of this study, a short fiber-reinforced composite can be used as a direct core buildup material that can effectively resist heavy occlusal forces against fracture and may reinforce the remaining tooth structure in endodontically treated teeth. Copyright © 2017 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

  1. Characterization of unidirectional carbon fiber reinforced polyamide-6 thermoplastic composite under longitudinal compression loading at high strain rate

    Science.gov (United States)

    Ploeckl, Marina; Kuhn, Peter; Koerber, Hannes

    2015-09-01

    In the presented work, an experimental investigation has been performed to characterize the strain rate dependency of unidirectional carbon fiber reinforced polyamide-6 composite for longitudinal compression loading. An end-loaded compression specimen geometry, suitable for contactless optical strain measurement via digital image correlation and dynamic loading in a split-Hopkinson pressure bar, was developed. For the dynamic experiments at a constant strain rate of 100 s-1 a modified version of the Dynamic Compression Fixture, developed by Koerber and Camanho [Koerber and Camanho, Composites Part A, 42, 462-470, 2011] was used. The results were compared with quasi-static test results at a strain rate of 3 · 10-4 s-1 using the same specimen geometry. It was found that the longitudinal compressive strength increased by 61% compared to the strength value obtained from the quasi-static tests.

  2. Effects of postcuring on mechanical properties of pultruded fiber-reinforced epoxy composites and the neat resin

    Science.gov (United States)

    Long, Edward R., Jr.; Long, Sheila Ann T.; Funk, Joan G.; Collins, William D.; Gray, Stephanie L.

    1989-01-01

    The effects of postcuring on mechanical properties of pultruded fiber-reinforced epoxy-resin composites have been investigated. Composites with carbon, glass, and aramid reinforcement fibers were individually studied. The epoxy was a commercially-available resin that was especially developed for pultrusion fabrication. The pultrusions were conducted at 400 F with postcures at 400, 450, 500, and 550 F. Measurements of the flexural, shear, and interlaminar fracture-toughness properties showed that significant postcuring can occur during the pultrusion process. All three mechanical properties were degraded by the higher (500 and 550 F) temperatures; photomicrographs suggest that the degradation was caused at the fiber-resin interface for all three fiber types.

  3. Axial shear modulus of a fiber-reinforced composite with random fiber cross-sections

    Directory of Open Access Journals (Sweden)

    S. K. Bose

    1982-01-01

    Full Text Available A study is made of the effective axial shear modulus of a fiber reinforced material with random fiber cross-sections so that the micromechanics is governed by stochastic differential equations. A coarse-graining procedure is adopted to investigate the macroscopic behavior of the material. This analysis leads to the formula for the effective axial shear modulus μ∗=μ1/{1−2c(μ2−μ1/(μ2+μ1},where μ1 and μ2 are the shear modulus of the matrix and fibers respectively and c is the concentration of the fibers less that 0.5. For c>0.5, the fiber and matrix moduli are to be interchanged and c is to be replaced by 1−c. The results of this study are compared with those of the theory of fibre reinforced materials. Finally, a numerical example is presented with graphical representation.

  4. Tensile strength and its scatter of unidirectional carbon fiber reinforced composites

    Energy Technology Data Exchange (ETDEWEB)

    Hamada, H.; Oya, N.; Yamashita, K.; Maekawa, Z.I. [Kyoto Inst. of Technology (Japan)

    1995-12-31

    0 (along the fiber direction) and 90 degree (transverse to the fiber direction) tension tests of Carbon Fiber Reinforced Plastics (CFRP) using a great number of specimens were conducted. Tensile properties and their scatter were evaluated by means of the data base. Materials used in this study were seven kinds of carbon fibers and three kinds of epoxy resins. Reinforcing fiber and matrix resin properties strongly affected on 0 and 90 degree properties of CFRP respectively. In 0 degree tension tests, fracture mode of specimen vaned in each material, and a relationship between the scatter of strength and the fracture mode existed. From the results of 9 degree tension tests, some differences of interfacial properties between each laminate were` also detected. According to some considerations on fracture mechanism in 0 degree tension test, it was deduced that the fracture mode depended on the balance of fiber, matrix and interface properties.

  5. Processing of continuous fiber reinforced ceramic composites for ultra high temperature applications using organosilicon polymer precursors

    Science.gov (United States)

    Nicholas, James Robert

    The current work is on the development of continuous fiber reinforced ceramic materials (CFCCs) for use in ultra high temperature applications. These applications subject materials to extremely high temperatures(> 2000°C). Monolithic ceramics are currently being used for these applications, but the tendency to fail catastrophically has driven the need for the next generation of material. Reinforcing with continuous fibers significantly improves the toughness of the monolithic materials; however, this is a manufacturing challenge. The development of commercial, low-viscosity preceramic polymers provides new opportunities to fabricate CFCCs. Preceramic polymers behave as polymers at low temperatures and are transformed into ceramics upon heating to high temperatures. The polymer precursors enable the adaptation of well-established polymer processing techniques to produce high quality materials at relatively low cost. In the present work, SMP-10 from Starfire Systems, and PURS from KiON Corp. were used to manufacture ZrB2-SiC/SiC CFCCs using low cost vacuum bagging process in conjunction with the polymer infiltration and pyrolysis process. The microstructure was investigated using scanning electron microscopy and it was determined that the initial greenbody cure produced porosity of both closed and open pores. The open pores were found to be more successfully re-infiltrated using neat resin compared to slurry reinfiltrate; however, the closed pores were found to be impenetrable during subsequent reinfiltrations. The mechanical performance of the manufactured samples was evaluated using flexure tests and found the fiber reinforcement prevented catastrophic failure behavior by increasing fracture toughness. Wedge sample were fabricated and evaluated to demonstrate the ability to produce CFCC of complex geometry.

  6. Corrosion of Continuous Fiber Reinforced Aluminum Metal Matrix Composites (CF-AMCs)

    Science.gov (United States)

    Tiwari, Shruti

    The first objective of this research is to study the atmospheric corrosion behavior of continuous reinforced aluminum matrix composites (CF-AMCs). The materials used for this research were alumina (Al2O3) and nickel (Ni) coated carbon (C) fibers reinforced AMCs. The major focus is to identify the correlation between atmospheric parameters and the corrosion rates of CF-AMCs in the multitude of microclimates and environments in Hawai'i. The micro-structures of CF-AMCs were obtained to correlate the microstructures with their corrosion performances. Also electrochemical polarization experiments were conducted in the laboratory to explain the corrosion mechanism of CF-AMCs. In addition, CF-AMCs were exposed to seven different test sites for three exposure periods. The various climatic conditions like temperature (T), relative humidity (RH), rainfall (RF), time of wetness (TOW), chloride (Cl- ) and sulfate (SO42-) deposition rate, and pH were monitored for three exposure period. Likewise, mass losses of CF-AMCs at each test site for three exposure periods were determined. The microstructure of the CF-AMCS showed that Al/C/50f MMCs contained a Ni-rich phase in the matrix, indicating that the Ni coating on the C fiber dissolved in the matrix. The intermetallic phases obtained in Al-2wt% Cu/Al 2O3/50f-T6 MMC and Al-2wt%-T6 monolith were rich in Cu and Fe. The intermetallic phases obtained in Al 7075/Al2O3/50f-T6 MMC and Al 7075-T6 monolith also contained traces of Mg, Zn, Ni, and Si. Electrochemical polarization experiment indicated that the Al/Al 2O3/50f Al-2wt% Cu/Al2O3/50f-T6 and Al 7075/Al2O3/50f-T6 MMC showed similar corrosion trends as their respective monoliths pure Al, Al-2wt%-T6 and Al 7075-T6 in both aerated and deaerated condition. Al2O3 fiber, being an insulator, did not have a great effect on the polarization behavior of the composites. Al/C/50f MMCs corroded at a much faster rate as compared to pure Al monolith due to the galvanic effect between C and Al

  7. Spectroscopic determination of the in-situ composition of epoxy matrices in glass fiber reinforced composites

    Science.gov (United States)

    Antoon, M. K.; Zehner, B. E.; Koenig, J. L.

    1980-01-01

    Computerized infrared analysis is applied to the characterization of a glass-reinforced crosslinked polyester. The method of factor analysis determines the number of independent components which constitute the polymeric matrix. Subsequently, the spectra of those components are fitted by a least-squares criterion to spectra of the multicomponent matrix, or, if the glass spectrum is included as an additional component, to the spectra of composites. The least-squares coefficients yield the matrix composition in terms of the initial reactant composition and the extent of crosslinking.

  8. A new system for posterior restorations: a combination of ceramic optimized polymer and fiber-reinforced composite.

    Science.gov (United States)

    Rosenthal, L; Trinkner, T; Pescatore, C

    1997-01-01

    Due to the need for increased strength characteristics and enhanced aesthetic expectations of the patients, metal-free, aesthetic restorative systems for the anterior and posterior dentition are currently available. A new "space-age" restorative material has been developed that is a combination of a ceramic optimized polymer (Ceromer) (Targis/Vectris, Ivoclar Williams, Amherst, NY) and a fiber-reinforced composite framework material. The purpose of this article is to discuss the qualities that render this material particularly suitable for a variety of indications, including laboratory-fabricated restorations for the stress-bearing posterior regions. The material lends itself to diversification. Its indication for inlays, onlays, full-coverage crown restorations, and conservative single pontic inlay bridges is presented.

  9. Mechanical Characterization of High-Performance Steel-Fiber Reinforced Cement Composites with Self-Healing Effect

    Directory of Open Access Journals (Sweden)

    Dong Joo Kim

    2014-01-01

    Full Text Available The crack self-healing behavior of high-performance steel-fiber reinforced cement composites (HPSFRCs was investigated. High-strength deformed steel fibers were employed in a high strength mortar with very fine silica sand to decreasing the crack width by generating higher interfacial bond strength. The width of micro-cracks, strongly affected by the type of fiber and sand, clearly produced the effects on the self-healing behavior. The use of fine silica sand in HPSFRCs with high strength deformed steel fibers successfully led to rapid healing owing to very fine cracks with width less than 20 µm. The use of very fine silica sand instead of normal sand produced 17%–19% higher tensile strength and 51%–58% smaller width of micro-cracks.

  10. Characterization and Effects of Fiber Pull-Outs in Hole Quality of Carbon Fiber Reinforced Plastics Composite

    Directory of Open Access Journals (Sweden)

    Sina Alizadeh Ashrafi

    2016-10-01

    Full Text Available Hole quality plays a crucial role in the production of close-tolerance holes utilized in aircraft assembly. Through drilling experiments of carbon fiber-reinforced plastic composites (CFRP, this study investigates the impact of varying drilling feed and speed conditions on fiber pull-out geometries and resulting hole quality parameters. For this study, hole quality parameters include hole size variance, hole roundness, and surface roughness. Fiber pull-out geometries are quantified by using scanning electron microscope (SEM images of the mechanically-sectioned CFRP-machined holes, to measure pull-out length and depth. Fiber pull-out geometries and the hole quality parameter results are dependent on the drilling feed and spindle speed condition, which determines the forces and undeformed chip thickness during the process. Fiber pull-out geometries influence surface roughness parameters from a surface profilometer, while their effect on other hole quality parameters obtained from a coordinate measuring machine is minimal.

  11. Carbon-Coated-Nylon-Fiber-Reinforced Cement Composites as an Intrinsically Smart Concrete for Damage Assessment during Dynamic Loading

    Institute of Scientific and Technical Information of China (English)

    Zhenjun ZHOU; Zhiguo XIAO; Wei PAN; Zhipeng XIE; Xixian LUO; Lei JIN

    2003-01-01

    Concrete containing short carbon-coated-nylon fibers (0.4~2.0 vol. pct) exhibited quasi-ductile response by developing a large damage zone prior to fracture localization. In the damage zone, the material was microcracked but continued to local strain-harden. The carbon-coated-nylon-fiber-reinforced concrete composites (NFRC) were found to be an intrinsically smart concrete that could sense elastic and inelastic deformation, as well as fracture. The fibers served to bridge the cracks and the carbon coating gave the conduction path. The signal provided came from the change in electrical resistance, which was reversible for elastic deformation and irreversible for inelastic deformation and fracture. The resistance decrease was due to the reduction of surface touch resistance between fiber and matrix and the crack closure. The resistance irreversible increase resulted from the crack opening and breakage of the carbon coating on nylon fiber.

  12. Effect of thermal residual stresses on yielding behavior under tensile or compressive loading of short fiber reinforced metal matrix composite

    Institute of Scientific and Technical Information of China (English)

    丁向东; 连建设; 江中浩; 孙军

    2001-01-01

    Using large strain two-dimension axisymmetric elasto-plastic finite element method and the modified law of mixture, the effects of thermal residual stresses on the yielding behavior of short fiber reinforced metal matrix composite and their dependencies on the material structure parameters (fiber volume fraction, fiber aspect ratio and fiber end distance) were studied. It is demonstrated that the stress-strain partition parameter can be used to describe the stress transfer from the matrix to the fiber. The variation of the second derivation of the stress-strain partition parameter can be used to determine the elastic modulus, the proportion limit, the initial and final yield strengths. In the presence of thermal residual stress, these yielding properties are asymmetric and are influenced differently by the material structure parameters under tensile and compressive loadings.

  13. On the Theory and Numerical Simulation of Cohesive Crack Propagation with Application to Fiber-Reinforced Composites

    Science.gov (United States)

    Rudraraju, Siva Shankar; Garikipati, Krishna; Waas, Anthony M.; Bednarcyk, Brett A.

    2013-01-01

    The phenomenon of crack propagation is among the predominant modes of failure in many natural and engineering structures, often leading to severe loss of structural integrity and catastrophic failure. Thus, the ability to understand and a priori simulate the evolution of this failure mode has been one of the cornerstones of applied mechanics and structural engineering and is broadly referred to as "fracture mechanics." The work reported herein focuses on extending this understanding, in the context of through-thickness crack propagation in cohesive materials, through the development of a continuum-level multiscale numerical framework, which represents cracks as displacement discontinuities across a surface of zero measure. This report presents the relevant theory, mathematical framework, numerical modeling, and experimental investigations of through-thickness crack propagation in fiber-reinforced composites using the Variational Multiscale Cohesive Method (VMCM) developed by the authors.

  14. Influence of retainer design on two-unit cantilever resin-bonded glass fiber reinforced composite fixed dental prostheses: An in vitro and finite element analysis study

    NARCIS (Netherlands)

    Keulemans, F.; de Jager, N.; Kleverlaan, C.J.; Feilzer, A.J.

    2008-01-01

    Purpose: The aim of this study was to evaluate in vitro the influence of retainer design on the strenght of two-unit cantilever resin-bonded glass fiber-reinforced composite (FRC) fixed dental prostheses (FDP). Conclusion: A dual-wing retainer is the optimal design for replacement of a single premol

  15. Fatigue resistance, debonding force, and failure type of fiber-reinforced composite, polyethylene ribbon-reinforced, and braided stainless steel wire lingual retainers in vitro

    NARCIS (Netherlands)

    Foek, Dave Lie Sam; Yetkiner, Enver; Ozcan, Mutlu

    2013-01-01

    Objective: To analyze the fatigue resistance, debonding force, and failure type of fiber-reinforced composite, polyethylene ribbon-reinforced, and braided stainless steel wire lingual retainers in vitro. Methods: Roots of human mandibular central incisors were covered with silicone, mimicking the pe

  16. The effect of a fiber reinforced cavity configuration on load bearing capacity and failure mode of endodontically treated molars restored with CAD/CAM resin composite overlay restorations

    NARCIS (Netherlands)

    Rocca, G.T.; Saratti, C.M.; Cattani-Lorente, M.; Feilzer, A.J.; Scherrer, S.; Krecji, I.

    2015-01-01

    Objectives To evaluate the fracture strength and the mode of failure of endodontically treated molars restored with CAD/CAM overlays with fiber reinforced composite build-up of the pulp chamber. Methods 40 Devitalized molars were cut over the CEJ and divided into five groups (n = 8). The pulp chambe

  17. Influence of retainer design on two-unit cantilever resin-bonded glass fiber reinforced composite fixed dental prostheses: An in vitro and finite element analysis study

    NARCIS (Netherlands)

    Keulemans, F.; de Jager, N.; Kleverlaan, C.J.; Feilzer, A.J.

    2008-01-01

    Purpose: The aim of this study was to evaluate in vitro the influence of retainer design on the strenght of two-unit cantilever resin-bonded glass fiber-reinforced composite (FRC) fixed dental prostheses (FDP). Conclusion: A dual-wing retainer is the optimal design for replacement of a single

  18. Effect of Red Mud and Copper Slag Particles on Physical and Mechanical Properties of Bamboo-Fiber-Reinforced Epoxy Composites

    Directory of Open Access Journals (Sweden)

    Sandhyarani Biswas

    2012-01-01

    Full Text Available In the present work, a series of bamboo-fiber-reinforced epoxy composites are fabricated by using red mud and copper slag particles as filler materials. A filler plays an important role in determining the properties and behavior of particulate composites. The effects of these two fillers on the mechanical properties of bamboo-epoxy composites are investigated. Comparative analysis shows that with the incorporation of these fillers, the tensile strength of the composites increases significantly, whereas the flexural strength and impact strength decrease with increase in filler content (red mud and copper slag fillers in the epoxy-bamboo fiber composites. The density and hardness are also affected by the type and content of filler particles. It is found that the addition of copper slag filler improves the hardness of the bamboo-epoxy composites, whereas the addition of red mud filler reduces the hardness value of bamboo-epoxy composites. The study reveals that the addition of copper slag filler in bamboo-epoxy composites shows better physical and mechanical properties as compared to the red-mud-filled composites.

  19. Interfacial toughening and consequent improvement in fracture toughness of carbon fiber reinforced epoxy resin composites: induced by diblock copolymers

    Directory of Open Access Journals (Sweden)

    X. D. Zhou

    2013-11-01

    Full Text Available Carbon fibers chemically grafted with hydroxyl-terminated diblock copolymer poly (n-butylacrylate-b-poly (glycidyl methacrylate (OH-PnBA-b-PGMA, were used as the reinforcement for epoxy composites. The multi-filament composite specimens were prepared and measured by dynamic mechanical analysis (DMA, to study the interfacial toughness of carbon fiber reinforced epoxy composites with the diblock copolymers. The loss modulus and loss factor peaks of β-relaxation indicated that composites with diblock copolymers could dissipate more energy at small strain and possess better interfacial toughness, whereas composites without the ductile block PnBA having the worse interfacial toughness. The glass transition temperature and the apparent activation energy calculated from the glass transition showed that the strong interfacial adhesion existed in the composites with diblock copolymers, corresponding with the value of interfacial shear strength. Therefore, a strengthening and toughening interfacial structure in carbon fiber/epoxy composites was achieved by introducing the diblock copolymer OH-PnBA-b-PGMA. The resulting impact toughness, characterized with an Izod impact tester, was better than that of composite without the ductile block PnBA.

  20. Nondestructive Evaluation of Fiber Reinforced Composites. A State-of-the-Art Survey. Volume 1. NDE of Graphite Fiber-Reinforced Plastic Composites. Part 1. Radiography and Ultrasonics

    Science.gov (United States)

    1982-03-01

    than simple fracture, thus helping Opposed cracks grow out from the hole. On the other to improve toughness. hand, in composites, cracks usually run ...show cracks run - ning back along the fibers and an extensive damage zone around the gross crack which has little in common with damage in metals. This... HIIT ’, U’ONX SPICIIMINS 1’ 1-116.4 mm (0.25 in.) I)IA .rlR HOlE: (I-rom Ref. 29, Reproduced from NTIACpuhlication. I’roccling% of 12rh Ni)I Synpo.sium

  1. Study of the strength and erosive behavior of CaCO3/glass fiber reinforced polyester composite

    Directory of Open Access Journals (Sweden)

    2008-12-01

    Full Text Available In this study, the strength and erosive characteristics of CaCO3 filled unsaturated polyester/glass fiber (UPR/GFR composite are evaluated. Samples of UPR with 40, 50 and 60 wt% content of CaCO3 and different CaCO3 particle sizes of 1, 2, 3, 5 and 10 micron were prepared and tested under tensile loading, indentation and erosion conditions. The tensile strength, hardness and erosion wear rate of unsaturated polyester/glass fiber (UPR composite/CaCO3 composite were obtained and evaluated. The results showed that the higher is the percentage of CaCO3 in the composite and the smaller is the CaCO3 particle size, the higher is the strength and the erosive resistance of the glass fiber reinforced/unsaturated polyester composite (UPR-GFR. Furthermore, the highest erosion wear rate is at 90° impingement angle. Finally the results show that the erosive wear of CaCO3 content UPR/GFR composite in a brittle manner.

  2. Physical and mechanical properties of poly(hydroxybutyrate-co-hydroxyvalerate) and its pineapple fiber-reinforced composites

    Science.gov (United States)

    Luo, Shuiyuan

    2000-10-01

    Recently, there has been considerable research on biodegradable polymers because of the complex plastic waste management created by the mostly non-degradable polymers and polymer-based composites. In this dissertation, physical and mechanical properties of poly(hydroxybutyrate-co-hydroxyvalerate) (PHBV), a degradable polymer, and its pineapple fiber-reinforced composites are discussed. CHAPTER ONE introduces the PHBV polymer, natural cellulose fibers, and polymeric composites including the fiber/matrix interface. The degradability of PHBV is also briefly discussed. CHAPTER TWO describes the effects of thermal processing time on the properties of PHBV. At processing conditions of 180°C and 140 MPa, PHBV underwent significant, random chain scission. As a result, tensile properties deteriorated. DSC and SAXS results show that thermally degraded PHBVs had different thermal properties and lamellar morphology. CHAPTER THREE reports the effects of 60Co gamma-radiation on the properties of PHBV. Under 60Co gamma-radiation random chain scission but no cross-linking occurred in PHBV. Chain scission occurs probably in the amorphous region. As a result, thermal and tensile properties are significantly affected. CHAPTER FOUR describes properties of pineapple fibers, the interface between pineapple fiber and PHBV, and properties of pineapple fiber-reinforced PHBV "green" composites. Pineapple fiber has enough strength to be used as reinforcement in composites with intermediate strength. Interfacial shear strength was moderate. The mechanical properties of PHBV were significantly improved, and were comparable to some woods. CHAPTER FIVE presents the mechanical and thermal properties of unidirectional, degradable, environment-friendly "green" composites made from pineapple fibers and PHBV resin. Tensile and flexural properties of the "green" composites with different fiber contents were investigated. The presence of pineapple fibers did not affect the non

  3. Investigations on Void Formation in Composite Molding Processes and Structural Damping in Fiber-Reinforced Composites with Nanoscale Reinforcements

    Science.gov (United States)

    DeValve, Caleb Joshua

    Fiber-reinforced composites (FRCs) offer a stronger and lighter weight alternative to traditional materials used in engineering components such as wind turbine blades and rotorcraft structures. Composites for these applications are often fabricated using liquid molding techniques, such as injection molding or resin transfer molding. One significant issue during these processing methods is void formation due to incomplete wet-out of the resin within the fiber preform, resulting in discontinuous material properties and localized failure zones in the material. A fundamental understanding of the resin evolution during processing is essential to designing processing conditions for void-free filling, which is the first objective of the dissertation. Secondly, FRCs used in rotorcraft experience severe vibrational loads during service, and improved damping characteristics of the composite structure are desirable. To this end, a second goal is to explore the use of matrix-embedded nanoscale reinforcements to augment the inherent damping capabilities in FRCs. The first objective is addressed through a computational modeling and simulation of the infiltrating dual-scale resin flow through the micro-architectures of woven fibrous preforms, accounting for the capillary effects within the fiber bundles. An analytical model is developed for the longitudinal permeability of flow through fibrous bundles and applied to simulations which provide detailed predictions of local air entrapment locations as the resin permeates the preform. Generalized design plots are presented for predicting the void content and processing time in terms of the Capillary and Reynolds Numbers governing the molding process. The second portion of the research investigates the damping enhancement provided to FRCs in static and rotational configurations by different types and weight fractions of matrix-embedded carbon nanotubes (CNTs) in high fiber volume fraction composites. The damping is measured using

  4. Flexural strengthening of reinforced concrete beams with carbon fibers reinforced polymer (CFRP sheet bonded to a transition layer of high performance cement-based composite

    Directory of Open Access Journals (Sweden)

    V. J. Ferrari

    Full Text Available Resistance to corrosion, high tensile strength, low weight, easiness and rapidity of application, are characteristics that have contributed to the spread of the strengthening technique characterized by bonding of carbon fibers reinforced polymer (CFRP. This research aimed to develop an innovate strengthening method for RC beams, based on a high performance cement-based composite of steel fibers (macro + microfibers to be applied as a transition layer. The purpose of this transition layer is better control the cracking of concrete and detain or even avoid premature debonding of strengthening. A preliminary study in short beams molded with steel fibers and strengthened with CFRP sheet, was carried out where was verified that the conception of the transition layer is valid. Tests were developed to get a cement-based composite with adequate characteristics to constitute the layer transition. Results showed the possibility to develop a high performance material with a pseudo strain-hardening behavior, high strength and fracture toughness. The application of the strengthening on the transition layer surface had significantly to improve the performance levels of the strengthened beam. It summary, it was proven the efficiency of the new strengthening technique, and much information can be used as criteria of projects for repaired and strengthened structures.

  5. Oxidation of SiC Fiber-Reinforced SiC Matrix Composites with a BN Interphase

    Science.gov (United States)

    Opila, Elizabeth; Boyd, Meredith K.

    2010-01-01

    SiC-fiber reinforced SiC matrix composites with a BN interphase were oxidized in reduced oxygen partial pressures of oxygen to simulate the environment for hypersonic vehicle leading edge applications. The constituent fibers as well as composite coupons were oxidized in oxygen partial pressures ranging from 1000 ppm O2 to 5% O2 balance argon. Exposure temperatures ranged from 816 C to 1353 C (1500 F to 2450 F). The oxidation kinetics of the coated fibers were monitored by thermogravimetric analysis (TGA). An initial rapid transient weight gain was observed followed by parabolic kinetics. Possible mechanisms for the transient oxidation are discussed. One edge of the composite coupon seal coat was ground off to simulate damage to the composite which allowed oxygen ingress to the interior of the composite. Oxidation kinetics of the coupons were characterized by scanning electron microscopy since the weight changes were minimal. It was found that sealing of the coupon edge by silica formation occurred. Differences in the amount and morphology of the sealing silica as a function of time, temperature and oxygen partial pressure are discussed. Implications for use of these materials for hypersonic vehicle leading edge materials are summarized.

  6. Crystallization behaviors of carbon fiber reinforced BN-Si{sub 3}N{sub 4} matrix composite

    Energy Technology Data Exchange (ETDEWEB)

    Li, Bin; Zhang, Chang-Rui; Wang, Si-Qing; Cao, Feng [State Key Laboratory of Advanced Ceramic Fibers and Composites, College of Aerospace and Materials Engineering, National University of Defense Technology, Changsha 410073 (China)

    2007-07-15

    The crystallization behaviors of a new carbon fiber reinforced composite with a hybrid matrix comprising BN and Si{sub 3}N{sub 4} prepared by precursor infiltration and pyrolysis were investigated by Fourier transform infrared spectroscopy, X-ray diffraction and scanning electron microscopy. The results show that the as-received composite is almost amorphous, and its main composition is BN and Si{sub 3}N{sub 4}. When heat treated at 1600 C, the composite is crystallized and shows a much better crystal form. When heat treated at 2100 C, Si{sub 3}N{sub 4} in the matrix is decomposed, and BN exhibits a relatively complete crystallization. The existence of B{sub 4}C and SiC is detected, which indicates the interfacial chemical reactions between nitride matrices and carbon fibers. The surface morphology of carbon fibers in the composite changed significantly when heated from 1600 to 2100 C, which also proved the occurrence of interfacial chemical reactions. (copyright 2007 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  7. Transitions in Wear and Friction of Carbon Fiber Reinforced Copper Matrix Composite Sliding Against AISI-1045 Steel

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    The friction and wear properties of carbon fiber reinforced copper matrix composite in dry sliding against AISI-1045 steel was evaluated by a block-on-ring test machine. It was shown that the low frictional factor and wear rate of the composite block could be maintained when pressure or velocity was below a certain value. But when the pressure or velocity exceeded the critical value, the friction factor and wear rate tended to increase rapidly with pressure and sliding velocity. The morphologies, elemental compositions, and surface profile of worn composite surfaces at different wear stages were analyzed by means of scanning electron microscopy, energy dispersive spectrometry, and profile-meter. It was found that low values of friction and wear were due to a thin solid film forming on the surface of the composite block which includes carbon and copper at a mild wear stage. The film could impede adhesion and provide some degree of self-lubrication. When the film included more metal elements and were damaged, severe wear happened, and the wear rate increased sharply. As a result, a transition diagram in friction and wear was constructed, which provided pressure and velocity conditions of change from mild wear and low friction to severe wear and high friction for the wear-resisting design.

  8. Effect of Fiber Geometry and Representative Volume Element on Elastic and Thermal Properties of Unidirectional Fiber-Reinforced Composites

    Directory of Open Access Journals (Sweden)

    Siva Bhaskara Rao Devireddy

    2014-01-01

    Full Text Available The aim of present work is focused on the evaluation of elastic and thermal properties of unidirectional fiber-reinforced polymer composites with different volume fractions of fiber up to 0.7 using micromechanical approach. Two ways for calculating the material properties, that is, analytical and numerical approaches, were presented. In numerical approach, finite element analysis was used to evaluate the elastic modulus and thermal conductivity of composite from the constituent material properties. The finite element model based on three-dimensional micromechanical representative volume element (RVE with a square and hexagonal packing geometry was implemented by using finite element code ANSYS. Circular cross section of fiber and square cross section of fiber were considered to develop RVE. The periodic boundary conditions are applied to the RVE to calculate elastic modulus of composite. The steady state heat transfer simulations were performed in thermal analysis to calculate thermal conductivity of composite. In analytical approach, the elastic modulus is calculated by rule of mixture, Halpin-Tsai model, and periodic microstructure. Thermal conductivity is calculated analytically by using rule of mixture, the Chawla model, and the Hashin model. The material properties obtained using finite element techniques were compared with different analytical methods and good agreement was achieved. The results are affected by a number of parameters such as volume fraction of the fibers, geometry of fiber, and RVE.

  9. Effects of Thermal and Humidity Aging on the Interfacial Adhesion of Polyketone Fiber Reinforced Natural Rubber Composites

    Directory of Open Access Journals (Sweden)

    Han Ki Lee

    2016-01-01

    Full Text Available Polyketone fiber is considered as a reinforcement of the mechanical rubber goods (MRG such as tires, automobile hoses, and belts because of its high strength and modulus. In order to apply it to those purposes, the high adhesion of fiber/rubber interface and good sustainability to aging conditions are very important. In this study, polyketone fiber reinforced natural rubber composites were prepared and they were subjected to thermal and humidity aging, to assess the changes of the interfacial adhesion and material properties. Also, the effect of adhesive primer treatment, based on the resorcinol formaldehyde resin and latex (RFL, of polyketone fiber for high interfacial adhesion was evaluated. Morphological and property changes of the rubber composites were analyzed by using various instrumental analyses. As a result, the rubber composite was aged largely by thermal aging at high temperature rather than humidity aging condition. Interfacial adhesion of the polyketone/NR composites was improved by the primer treatment and its effect was maintained in aging conditions.

  10. Flame Retardancy Effects of Graphene Nanoplatelet/Carbon Nanotube Hybrid Membranes on Carbon Fiber Reinforced Epoxy Composites

    Directory of Open Access Journals (Sweden)

    Dongxian Zhuo

    2013-01-01

    Full Text Available Carbon nanotube/graphene nanoplatelet (MWCNT/GNP hybrid membranes with lower liquid permeability and better barrier effect compared to MWCNT membranes were successfully synthesized by vacuum filtering. Their morphologies, water permeability, and pore structures were characterized by a scanning electron microscope (SEM and nitrogen adsorption isotherms. Furthermore, MWCNT/GNP membranes were used to improve the flame retardancy of carbon fiber reinforced polymer (CFRP composites, and the influence of weight percentage of GNPs on the permeability and flame retardancy of MWCNT/GNP membranes was systematically investigated. Results show that incorporation of MWCNT/GNP membranes on CFRP composite plates can remarkably improve the flame retardancy of CFRP composites. Specifically, the incorporation of hierarchical MWCNT/GNP membrane with 7.5 wt% of GNP displays a 35% reduction in the peak heat release rate (PHRR for a CFRP composite plate with the epoxy as matrix and a 11% reduction in PHRR compared with the incorporation of MWCNT membrane only. A synergistic flame retarding mechanism is suggested to be attributed to these results, which includes controlling the pore size and penetrative network structure.

  11. Impact of long-term thermal exposure on a SiC fiber-reinforced copper matrix composite

    Energy Technology Data Exchange (ETDEWEB)

    Kimmig, S.; Elgeti, S.; You, Jeong-Ha, E-mail: you@ipp.mpg.de

    2013-11-15

    Silicon carbide long fiber-reinforced copper matrix composites offer huge potential as a heat sink material of divertor for applications at temperatures above 300 °C thanks to the beneficial combination of strong ceramic fibers and highly conductive copper. For applications at higher operation temperatures, long term thermal stability is an issue, as thermal exposure may cause a detrimental change in microstructure in terms of chemistry and integrity of the constituents leading to overall deterioration of composite strength. The aim of this study is to investigate the impact of long term thermal exposure at an elevated temperature on a Cu/SiC{sub f} composite material. To this end, composite samples were fabricated and subjected to a heat treatment at 550 °C for 400 h. Extensive tensile tests were conducted for a wide range of fibers volume fractions to evaluate the strength before and after the heat treatment. Acoustic emission was detected in situ during tensile tests for tracking the failure events. Microscopic analysis was carried out to capture the chemical change and damage. It turned out that the applied heat treatment caused significant reduction of strength. Microanalysis revealed that infiltration and diffusion of copper into the fibers via the cracks of the damaged fibers are the direct cause of the embrittlement.

  12. Impact of long-term thermal exposure on a SiC fiber-reinforced copper matrix composite

    Science.gov (United States)

    Kimmig, S.; Elgeti, S.; You, Jeong-Ha

    2013-11-01

    Silicon carbide long fiber-reinforced copper matrix composites offer huge potential as a heat sink material of divertor for applications at temperatures above 300 °C thanks to the beneficial combination of strong ceramic fibers and highly conductive copper. For applications at higher operation temperatures, long term thermal stability is an issue, as thermal exposure may cause a detrimental change in microstructure in terms of chemistry and integrity of the constituents leading to overall deterioration of composite strength. The aim of this study is to investigate the impact of long term thermal exposure at an elevated temperature on a Cu/SiCf composite material. To this end, composite samples were fabricated and subjected to a heat treatment at 550 °C for 400 h. Extensive tensile tests were conducted for a wide range of fibers volume fractions to evaluate the strength before and after the heat treatment. Acoustic emission was detected in situ during tensile tests for tracking the failure events. Microscopic analysis was carried out to capture the chemical change and damage. It turned out that the applied heat treatment caused significant reduction of strength. Microanalysis revealed that infiltration and diffusion of copper into the fibers via the cracks of the damaged fibers are the direct cause of the embrittlement.

  13. Fundamental Studies of Low Velocity Impact Resistance of Graphite Fiber Reinforced Polymer Matrix Composites. Ph.D. Thesis

    Science.gov (United States)

    Bowles, K. J.

    1985-01-01

    A study was conducted to relate the impact resistance of graphite fiber reinforced composites with matrix properties through gaining an understanding of the basic mechanics involved in the deformation and fracture process, and the effect of the polymer matrix structure on these mechanisms. It was found that the resin matrix structure influences the composite impact resistance in at least two ways. The integration of flexibilizers into the polymer chain structure tends to reduce the T sub g and the mechanical properties of the polymer. The reduction in the mechanical properties of the matrix does not enhance the composite impact resistance because it allows matrix controlled failure to initiate impact damage. It was found that when the instrumented dropweight impact tester is used as a means for assessing resin toughness, the resin toughness is enhanced by the ability of the clamped specimen to deflect enough to produce sufficient membrane action to support a significant amount of the load. The results of this study indicate that crossplied composite impact resistance is very much dependent on the matrix mechanical properties.

  14. Micromechanical analysis of a hybrid composite—effect of boron carbide particles on the elastic properties of basalt fiber reinforced polymer composite

    Science.gov (United States)

    Krishna Golla, Sai; Prasanthi, P.

    2016-11-01

    A fiber reinforced polymer (FRP) composite is an important material for structural application. The diversified application of FRP composites has become the center of attention for interdisciplinary research. However, improvements in the mechanical properties of this class of materials are still under research for different applications. The reinforcement of inorganic particles in a composite improves its structural properties due to their high stiffness. The present research work is focused on the prediction of the mechanical properties of the hybrid composites where continuous fibers are reinforced in a micro boron carbide particle mixed polypropylene matrix. The effectiveness of the addition of 30 wt. % of boron carbide (B4C) particle contributions regarding the longitudinal and transverse properties of the basalt fiber reinforced polymer composite at various fiber volume fractions is examined by finite element analysis (FEA). The experimental approach is the best way to determine the properties of the composite but it is expensive and time-consuming. Therefore, the finite element method (FEM) and analytical methods are the viable methods for the determination of the composite properties. The FEM results were obtained by adopting a micromechanics approach with the support of FEM. Assuming a uniform distribution of reinforcement and considering one unit-cell of the whole array, the properties of the composite materials are determined. The predicted elastic properties from FEA are compared with the analytical results. The results suggest that B4C particles are a good reinforcement for the enhancement of the transverse properties of basalt fiber reinforced polypropylene.

  15. Push-out bond strength between composite core buildup and fiber-reinforced posts after different surface treatments.

    Science.gov (United States)

    Arslan, Hakan; Barutcigil, Cagatay; Yılmaz, Cenk Burak; Ceyhanlı, Kadir Tolga; Topcuoglu, Hüseyin Sinan

    2013-07-01

    The aim of this study was to evaluate the effects of different surface treatments on the pushout bond strength of fiber-reinforced posts to composite resin cores. Twenty-five translucent glass fiber posts were divided into five groups according to surface treatment methods as follows: an untreated control group, a group coated with silicated alumina particles (Co-Jet system, 3M ESPE, St. Paul, MN), and three groups undergoing surface preparation with erbium:yttrium-aluminum-garnet (Er:YAG) laser under three different power settings (150, 300, and 450 mJ at 10 Hz for 60 sec at 100 μs duration). After surface treatment, fiber posts were built up to a dual cure composite resin core. All of the specimens were set and sectioned perpendicularly along the long axis of the post using a saw. Two discs (thickness of 2 mm) were obtained from each post-core sample; finally, each group consisted of 10 samples. For artificial aging, the specimens were stored in water (37°C) for 24 h and subjected to thermal cycling (5000 cycles, 5-55°C, and 30 sec dwell time). Pushout tests were performed using a universal testing machine at a crosshead speed of 0.5 mm/min. The pushout pressure values were measured in MPa and analyzed using one way analysis of variance (ANOVA) and Tukey's honestly significant difference (HSD) post-hoc test (pstrength values ranged between 14,949 and 23,879 MPa. The lowest values were observed in the groups treated with the Er:YAG laser at 150 mJ. Irradiation by the Er:YAG laser at 450 mJ affected the bond strength significantly (pstrength increased relatively (19,184 MPa). Er:YAG laser irradiation enhanced the bond strength of fiber-reinforced posts to composite resin cores depending upon the power applied; Co-Jet sandblasting also increased the bond strength.

  16. Microstructures and properties of graphite and Al2O3 short fibers reinforced Mg-Al-Zn alloy hybrid composites

    Institute of Scientific and Technical Information of China (English)

    YANG Xiao-hong; LIU Yong-bing; SONG Qi-fei; AN Jian

    2006-01-01

    Graphite and Al2O3 short fibers reinforced Mg-Al-Zn alloy hybrid composites were fabricated by perform squeeze-infiltration route. The effects of the volume of graphite particles on the microstructure, mechanical properties and tribological behavior were investigated under the conditions of constant size of graphite particle and volume of Al2O3 short fiber. The results reveal that the uniform distribution of the reinforced graphite particles and Al2O3 short fiber can be obtained by this technique, and they have strong bonding with the metal matrix. Increasing graphite volume results in decrease in hardness, the ultimate tensile strength whereas the Al2O3 short fiber makes contribution to the increase in hardness of the composite. The composite exhibits good wear resistance, small wear mass loss and low coefficient of friction as compared with the metal matrix. The wear mechanisms transit from oxidation wear, abrasion wear into delamination wear as the applied load is increased, and a film of lubricant covering almost entire surface of specimen, is found to be formed, which separates the wear surfaces from metal to metal contact and thus improves the tribological properties.

  17. Preparation and thermal shock resistance of high emissivity molybdenum disilicide- aluminoborosilicate glass hybrid coating on fiber reinforced aerogel composite

    Science.gov (United States)

    Shao, Gaofeng; Lu, Yucao; Wu, Xiaodong; Wu, Jun; Cui, Sheng; Jiao, Jian; Shen, Xiaodong

    2017-09-01

    To develop a flexible reusable surface insulation for thermal protection system, MoSi2-aluminoborosilicate glass hybrid coatings have been prepared on Al2O3 fiber reinforced Al2O3-SiO2 aerogel composite by slurry dipping and rapid sintering method. The effect of MoSi2 content on radiative property and thermal shock behavior was investigated. The total emissivity values of all the coatings exceeded 0.85 in the wavelength of 0.8-2.5 μm. The M10 and M50 coatings were up to 0.9, which was due to the highest amorphous glass content of the M10 coating and the largest surface roughness of the M50 coating. The M30 coated composite showed the best thermal shock resistance with only 0.023% weight loss after 20 thermal shock cycles between 1473 K and room temperature, which was attributed to the similar thermal expansion coefficients between the coating and the substrate and the appropriate viscosity of aluminoborosilicate glass at 1473 K. The cracks resulted from CTE mismatch stress with different sizes formed and grew on the surface of M10, M40 and M50 coated samples, leading to the failure of the composites.

  18. Fatigue Life Prediction of Fiber-Reinforced Ceramic-Matrix Composites with Different Fiber Preforms at Room and Elevated Temperatures

    Directory of Open Access Journals (Sweden)

    Longbiao Li

    2016-03-01

    Full Text Available In this paper, the fatigue life of fiber-reinforced ceramic-matrix composites (CMCs with different fiber preforms, i.e., unidirectional, cross-ply, 2D (two dimensional, 2.5D and 3D CMCs at room and elevated temperatures in air and oxidative environments, has been predicted using the micromechanics approach. An effective coefficient of the fiber volume fraction along the loading direction (ECFL was introduced to describe the fiber architecture of preforms. The statistical matrix multicracking model and fracture mechanics interface debonding criterion were used to determine the matrix crack spacing and interface debonded length. Under cyclic fatigue loading, the fiber broken fraction was determined by combining the interface wear model and fiber statistical failure model at room temperature, and interface/fiber oxidation model, interface wear model and fiber statistical failure model at elevated temperatures, based on the assumption that the fiber strength is subjected to two-parameter Weibull distribution and the load carried by broken and intact fibers satisfies the Global Load Sharing (GLS criterion. When the broken fiber fraction approaches the critical value, the composites fatigue fracture.

  19. Computational modeling of the electromagnetic characteristics of carbon fiber-reinforced polymer composites with different weave structures

    Science.gov (United States)

    Hassan, A. M.; Douglas, J. F.; Garboczi, E. J.

    2014-02-01

    Carbon fiber reinforced polymer composites (CFRPC) are of great interest in the aerospace and automotive industries due to their exceptional mechanical properties. Carbon fibers are typically woven and inter-laced perpendicularly in warps and wefts to form a carbon fabric that can be embedded in a binding matrix. The warps and wefts can be interlaced in different patterns called weaving structures. The primary weaving structures are the plain, twill, and satin weaves, which give different mechanical composite properties. The goal of this work is to computationally investigate the dependence of CFRPC microwave and terahertz electromagnetic characteristics on weave structure. These bands are good candidates for the Nondestructive Evaluation (NDE) of CFRPC since their wavelengths are comparable to the main weave features. 3D full wave electromagnetic simulations of several different weave models have been performed using a finite element (FEM) simulator, which is able to accurately model the complex weave structure. The computational experiments demonstrate that the reflection of electromagnetic waves from CFRPC depend sensitively on weave structure. The reflection spectra calculated in this work can be used to identify the optimal frequencies for the NDE of each weave structure.

  20. Effect of Expansive Admixtures on the Shrinkage and Mechanical Properties of High-Performance Fiber-Reinforced Cement Composites

    Directory of Open Access Journals (Sweden)

    Won-Chang Choi

    2013-01-01

    Full Text Available High-performance fiber-reinforced cement composites (HPFRCCs are characterized by strain-hardening and multiple cracking during the inelastic deformation process, but they also develop high shrinkage strain. This study investigates the effects of replacing Portland cement with calcium sulfoaluminate-based expansive admixtures (CSA EXAs to compensate for the shrinkage and associated mechanical behavior of HPFRCCs. Two types of CSA EXA (CSA-K and CSA-J, each with a different chemical composition, are used in this study. Various replacement ratios (0%, 8%, 10%, 12%, and 14% by weight of cement of CSA EXA are considered for the design of HPFRCC mixtures reinforced with 1.5% polyethylene (PE fibers by volume. Mechanical properties, such as shrinkage compensation, compressive strength, flexural strength, and direct tensile strength, of the HPFRCC mixtures are examined. Also, crack width and development are investigated to determine the effects of the EXAs on the performance of the HPFRCC mixtures, and a performance index is used to quantify the performance of mixture. The results indicate that replacements of 10% CSA-K (Type 1 and 8% CSA-J (Type 2 considerably enhance the mechanical properties and reduce shrinkage of HPFRCCs.

  1. Fracture Resistance of Endodontically Treated Teeth Restored With Bulk Fill, Bulk Fill Flowable, Fiber-reinforced, and Conventional Resin Composite.

    Science.gov (United States)

    Atalay, C; Yazici, A R; Horuztepe, A; Nagas, E; Ertan, A; Ozgunaltay, G

    2016-01-01

    The aim of this in vitro study was to evaluate the fracture resistance of endodontically treated teeth restored with different types of restorative resins. Seventy-two sound maxillary premolar teeth were randomly divided into six groups (n=12). The teeth in the first group were left intact and tested as unprepared negative control (group I) specimens. The teeth in the remaining five groups were prepared with MOD cavities and endodontically treated. The teeth in one of the five groups (positive control group II) were unrestored. The rest of the prepared cavities were restored as follows: group III: bulk fill resin composite/Filtek Bulk Fill (3M ESPE); group IV: bulk fill flowable resin composite + nanohybrid/SureFil SDR Flow + Ceram.X Mono (Dentsply); group V: fiber-reinforced composite + posterior resin composite/GC everX posterior + G-aenial posterior (GC Corp.); and group VI: nanohybrid resin composite/Tetric N-Ceram (Ivoclar/Vivadent). Each restorative material was used with its respective adhesive system. The restored teeth were stored in distilled water for 24 hours at 37°C and were then thermocycled (5-55°C, 1000×). Specimens were subjected to a compressive load until fracture at a crosshead speed of 0.5 mm/min. The data were analyzed using one-way analysis of variance followed by the post hoc Tukey honestly significantly different test (p0.05). The lowest values were obtained in the positive control group (group II); these values were significantly lower than those of the other groups (pcomposite were not different from those restored with conventional nanohybrid resin composite.

  2. Optimal design of variable-stiffness fiber-reinforced composites using cellular automata

    NARCIS (Netherlands)

    Setoodeh, S.

    2005-01-01

    Growing number of applications of composites materials in aerospace and naval structures along with advancements in manufacturing technologies demand continuous innovations in design of composite structures. In the traditional design of composite laminates, fiber orientation angles are constant for

  3. In vitro antimicrobial properties of silver-polysaccharide coatings on porous fiber-reinforced composites for bone implants.

    Science.gov (United States)

    Nganga, Sara; Travan, Andrea; Marsich, Eleonora; Donati, Ivan; Söderling, Eva; Moritz, Niko; Paoletti, Sergio; Vallittu, Pekka K

    2013-12-01

    Biostable fiber-reinforced composite (FRC) implants prepared from bisphenol-A-dimethacrylate and triethyleneglycoldimethacrylate resin reinforced with E-glass fibers have been successfully used in cranial reconstructions in 15 patients. Recently, porous FRC structures were suggested as potential implant materials. Compared with smooth surface, porous surface allows implant incorporation via bone ingrowth, but is also a subject to bacterial attachment. Non-cytotoxic silver-polysaccharide nanocomposite coatings may provide a way to decrease the risk of bacterial contamination of porous FRC structures. This study is focused on the in vitro characterization of the effect porosity on the antimicrobial efficiency of the coatings against Staphylococcus aureus and Pseudomonas aeruginosa by a series of microbiological tests (initial adhesion, antimicrobial efficacy, and biofilm formation). Characterization included confocal laser scanning microscopy and scanning electron microscopy. The effect of porosity on the initial attachment of S. aureus was pronounced, but in the case of P. aeruginosa the effect was negligible. There were no significant effects of the coatings on the initial bacterial attachment. In the antimicrobial efficacy test, the coatings were potent against both strains regardless of the sample morphology. In the biofilm tests, there were no clear effects either of morphology or of the coating. Further coating development is foreseen to achieve a longer-term antimicrobial effect to inhibiting bacterial implant colonization.

  4. Monotonic and cyclic responses of impact polypropylene and continuous glass fiber-reinforced impact polypropylene composites at different strain rates

    KAUST Repository

    Yudhanto, Arief

    2016-03-08

    Impact copolymer polypropylene (IPP), a blend of isotactic polypropylene and ethylene-propylene rubber, and its continuous glass fiber composite form (glass fiber-reinforced impact polypropylene, GFIPP) are promising materials for impact-prone automotive structures. However, basic mechanical properties and corresponding damage of IPP and GFIPP at different rates, which are of keen interest in the material development stage and numerical tool validation, have not been reported. Here, we applied monotonic and cyclic tensile loads to IPP and GFIPP at different strain rates (0.001/s, 0.01/s and 0.1/s) to study the mechanical properties, failure modes and the damage parameters. We used monotonic and cyclic tests to obtain mechanical properties and define damage parameters, respectively. We also used scanning electron microscopy (SEM) images to visualize the failure mode. We found that IPP generally exhibits brittle fracture (with relatively low failure strain of 2.69-3.74%) and viscoelastic-viscoplastic behavior. GFIPP [90]8 is generally insensitive to strain rate due to localized damage initiation mostly in the matrix phase leading to catastrophic transverse failure. In contrast, GFIPP [±45]s is sensitive to the strain rate as indicated by the change in shear modulus, shear strength and failure mode.

  5. A testing platform for durability studies of polymers and fiber-reinforced polymer composites under concurrent hygrothermo-mechanical stimuli.

    Science.gov (United States)

    Gomez, Antonio; Pires, Robert; Yambao, Alyssa; La Saponara, Valeria

    2014-12-11

    The durability of polymers and fiber-reinforced polymer composites under service condition is a critical aspect to be addressed for their robust designs and condition-based maintenance. These materials are adopted in a wide range of engineering applications, from aircraft and ship structures, to bridges, wind turbine blades, biomaterials and biomedical implants. Polymers are viscoelastic materials, and their response may be highly nonlinear and thus make it challenging to predict and monitor their in-service performance. The laboratory-scale testing platform presented herein assists the investigation of the influence of concurrent mechanical loadings and environmental conditions on these materials. The platform was designed to be low-cost and user-friendly. Its chemically resistant materials make the platform adaptable to studies of chemical degradation due to in-service exposure to fluids. An example of experiment was conducted at RT on closed-cell polyurethane foam samples loaded with a weight corresponding to ~50% of their ultimate static and dry load. Results show that the testing apparatus is appropriate for these studies. Results also highlight the larger vulnerability of the polymer under concurrent loading, based on the higher mid-point displacements and lower residual failure loads. Recommendations are made for additional improvements to the testing apparatus.

  6. A glass fiber-reinforced composite - bioactive glass cranioplasty implant: A case study of an early development stage implant removed due to a late infection.

    Science.gov (United States)

    Posti, Jussi P; Piitulainen, Jaakko M; Hupa, Leena; Fagerlund, Susanne; Frantzén, Janek; Aitasalo, Kalle M J; Vuorinen, Ville; Serlo, Willy; Syrjänen, Stina; Vallittu, Pekka K

    2015-03-01

    This case study describes the properties of an early development stage bioactive glass containing fiber-reinforced composite calvarial implant with histology that has been in function for two years and three months. The patient is a 33-year old woman with a history of substance abuse, who sustained a severe traumatic brain injury later unsuccessfully treated with an autologous bone flap and a custom-made porous polyethylene implant. She was thereafter treated with developmental stage glass fiber-reinforced composite - bioactive glass implant. After two years and three months, the implant was removed due to an implant site infection. The implant was analyzed histologically, mechanically, and in terms of chemistry and dissolution of bioactive glass. Mechanical integrity of the load bearing fiber-reinforced composite part of the implant was not affected by the in vivo period. Bioactive glass particles demonstrated surface layers of hydroxyapatite like mineral and dissolution, and related increase of pH was considerably less after two and three months period than that for fresh bioactive glass. There was a difference in the histology of the tissues inside the implant areas near to the margin of the implant that absorbed blood during implant installation surgery, showed fibrous tissue with blood vessels, osteoblasts, collagenous fibers with osteoid formation, and tiny clusters of more mature hard tissue. In the center of the implant, where there was less absorbed blood, only fibrous tissue was observed. This finding is in line with the combined positron emission tomography - computed tomography examination with (18F)-fluoride marker, which demonstrated activity of the mineralizing bone by osteoblasts especially at the area near to the margin of the implant 10 months after implantation. Based on these promising reactions found in the bioactive glass containing fiber-reinforced composite implant that has been implanted for two years and three months, calvarial

  7. ′Metal to resin′: A comparative evaluation of conventional band and loop space maintainer with the fiber reinforced composite resin space maintainer in children

    OpenAIRE

    Garg, A.; Samadi, F.; J N Jaiswal; Saha, S.

    2014-01-01

    Aims: To compare the clinical efficacy of two space maintainers namely, conventional band and loop and Fiber Reinforced Composite Resin (FRCR) space maintainers . Subjects and Methods: Thirty healthy children, aged 5 to 8 years were selected having at least two deciduous molars in different quadrants indicated for extraction or lost previously. FRCR space maintainer was placed in one quadrant and in the other quadrant band and loop space maintainer was cemented. All the patients were recalled...

  8. Constructing Novel Fiber Reinforced Plastic (FRP) Composites through a Biomimetic Approach: Connecting Glass Fiber with Nanosized Boron Nitride by Polydopamine Coating

    OpenAIRE

    XueMei Wen; ZaoZao Xiao; Tao Jiang; Jian Li; Wei Zhang; Lei Zhang; Huaiqi Shao

    2013-01-01

    A biomimetic method was developed to construct novel fiber reinforced plastic (FRP) composites. By mimicking mussel adhesive proteins, a monolayer of polydopamine was coated on glass fiber (GF) surface. The polydopamine-treated GF (D-GF) adsorbed boron nitride (BN) nanoparticles, while obtaining micronano multiscale hybrid fillers BN-D-GF. Scanning electron microscopy (SEM) results showed that the strong interfacial interaction brought by the polydopamine benefits the loading amount as well ...

  9. Assessment of Tensile Bond Strength of Fiber-Reinforced Composite Resin to Enamel Using Two Types of Resin Cements and Three Surface Treatment Methods

    Directory of Open Access Journals (Sweden)

    Tahereh Ghaffari

    2015-10-01

    Full Text Available Background: Resin-bonded bridgework with a metal framework is one of the most conservative ways to replace a tooth with intact abutments. Visibility of metal substructure and debonding are the complications of these bridgeworks. Today, with the introduction of fiber-reinforced composite resins, it is possible to overcome these complications. The aim of this study was to evaluate the bond strength of fiber-reinforced composite resin materials (FRC to enamel. Methods: Seventy-two labial cross-sections were prepared from intact extracted teeth. Seventy-two rectangular samples of cured Vectris were prepared and their thickness was increased by adding Targis. The samples were divided into 3 groups for three different surface treatments: sandblasting, etching with 9% hydrofluoric acid, and roughening with a round tapered diamond bur. Each group was then divided into two subgroups for bonding to etched enamel by Enforce and Variolink II resin cements. Instron universal testing machine was used to apply a tensile force. The fracture force was recorded and the mode of failure was identified under a reflective microscope. Results: There were no significant differences in bond strength between the three surface treatment groups (P=0.53. The mean bond strength of Variolink II cement was greater than that of Enforce (P=0.04. There was no relationship between the failure modes (cohesive and adhesive and the two cement types. There was some association between surface treatment and failure mode. There were adhesive failures in sandblasted and diamond-roughened groups and the cohesive failure was dominant in the etched group. Conclusion: It is recommended that restorations made of fiber-reinforced composite resin be cemented with VariolinkII and surface-treated by hydrofluoric acid. Keywords: Tensile bond strength; surface treatment methods; fiber-reinforced composite resin

  10. Deformation behavior of carbon-fiber reinforced shape-memory-polymer composites used for deployable structures (Conference Presentation)

    Science.gov (United States)

    Lan, Xin; Liu, Liwu; Li, Fengfeng; Pan, Chengtong; Liu, Yanju; Leng, Jinsong

    2017-04-01

    Shape memory polymers (SMPs) are a new type of smart material, they perform large reversible deformation with a certain external stimulus (e.g., heat and electricity). The properties (e.g., stiffness, strength and other mechanically static or quasi-static load-bearing capacity) are primarily considered for conventional resin-based composite materials which are mainly used for structural materials. By contrast, the mechanical actuating performance with finite deformation is considered for the shape memory polymers and their composites which can be used for both structural materials and functional materials. For shape memory polymers and their composites, the performance of active deformation is expected to further promote the development in smart active deformation structures, such as deployable space structures and morphing wing aircraft. The shape memory polymer composites (SMPCs) are also one type of High Strain Composite (HSC). The space deployable structures based on carbon fiber reinforced shape memory polymer composites (SMPCs) show great prospects. Considering the problems that SMPCs are difficult to meet the practical applications in space deployable structures in the recent ten years, this paper aims to research the mechanics of deformation, actuation and failure of SMPCs. In the overall view of the shape memory polymer material's nonlinearity (nonlinearity and stress softening in the process of pre-deformation and recovery, relaxation in storage process, irreversible deformation), by the multiple verifications among theory, finite element and experiments, one obtains the deformation and actuation mechanism for the process of "pre-deformation, energy storage and actuation" and its non-fracture constraint domain. Then, the parameters of SMPCs will be optimized. Theoretical analysis is realized by the strain energy function, additionally considering the interaction strain energy between the fiber and the matrix. For the common resin-based or soft

  11. Mechanical Properties of Coir Rope-Glass Fibers Reinforced Polymer Hybrid Composites

    Directory of Open Access Journals (Sweden)

    B.Bakri

    2015-10-01

    Full Text Available Natural fiber composites have been developed and taken more attention in the last decades. Coir fiber is the natural fiber which has been used as reinforcement of composites. This fiber is hybridized with glass fiber for reinforcement composite. In this paper, coir rope and glass fibers were combined as reinforcement into hybrid composites with unsaturated polyester resin as matrix. The composition of fibers and matrix into hybrid composites are used 30:70 (volume fraction with unsaturated polyester. Volume fractions of coir rope mat and glass fiber mat in hybrid composites are 10:20, 15:15 and 20:10 respectively. The mechanical properties of the coir rope-glass fiber composite hybrid were described in this paper. Their properties include tensile strength, tensile modulus, flexural strength, flexural modulus, impact energy and impact strength. Fractography of tensile composite hybrid is also analyzed using Scanning Electron Microscope.

  12. Processing and characterization of natural fiber reinforced thermoplastic composites using micro-braiding technique

    Science.gov (United States)

    Kobayashi, Satoshi; Ogihara, Shinji

    In the present study, we investigate fatigue properties of green composites. A hemp fiber yarn reinforced poly(lactic acid) composite was selected as a green composite. Unidirectional (UD) and textile (Textile) composites were fabricated using micro-braiding technique. Fatigue tests results indicated that fatigue damages in UD composites was splitting which occurred just before the final fracture, while matrix crack and debonding between matrix and fiber yarn occurred and accumulated stably in Textile composites. These results were consistent with modulus reduction and acoustic emission measurement during fatigue tests.

  13. Part I. Corrosion studies of continuous alumina fiber reinforced aluminum-matrix composites. Part II. Galvanic corrosion between continuous alumina fiber reinforced aluminum-matrix composites and 4340 steel

    Science.gov (United States)

    Zhu, Jun

    Part I. The corrosion performance of continuous alumina fiber reinforced aluminum-matrix composites (CF-AMCs) was investigated in both the laboratory and field environments by comparing them with their respective monolithic matrix alloys, i.e., pure Al, A1-2wt%Cu T6, and Al 6061 T6. The corrosion initiation sites were identified by monitoring the changes in the surface morphology. Corrosion current densities and pH profiles at localized corrosion sites were measured using the scanning-vibrating electrode technique and the scanning ion-selective electrode technique, respectively. The corrosion damage of the materials immersed in various electrolytes, as well as those exposed in a humidity chamber and outdoor environments, was evaluated. Potentiodynamic polarization behavior was also studied. The corrosion initiation for the composites in 3.15 wt% NaCl occurred primarily around the Fe-rich intermetallic particles, which preferentially existed around the fiber/matrix interface on the composites. The corrosion initiation sites were also caused by physical damage (e.g., localized deformation) to the composite surface. At localized corrosion sites, the buildup of acidity was enhanced by the formation of micro-crevices resulting from fibers left in relief as the matrix corroded. The composites that were tested in exposure experiments exhibited higher corrosion rates than their monolithic alloys. The composites and their monolithic alloys were subjected to pitting corrosion when anodically polarized in the 3.15 wt% NaCl, while they passivated when anodically polarized in 0.5 M Na2SO4. The experimental results indicated that the composites exhibited inferior corrosion resistance compared to their monolithic matrix alloys. Part II. Galvanic corrosion studies were conducted on CF-AMCs coupled to 4340 steel since CF-AMCs have low density and excellent mechanical properties and are being considered as potential jacketing materials for reinforcing steel gun barrels. Coupled and

  14. Application of radiation-crosslinked polytetrafluoroethylene to fiber-reinforced composite materials

    Energy Technology Data Exchange (ETDEWEB)

    Oshima, Akihiro E-mail: aks@taka.jaeri.go.jp; Udagawa, Akira; Morita, Yousuke

    2001-07-01

    Plain-woven carbon fiber-filled polytetrafluoroethylene (PTFE) composites were fabricated by radiation-crosslinking under selective conditions. High mechanical and frictional properties are found in the composite materials compared with crosslinked PTFE without fiber. The composite materials with optional shapes, which are laminated after electron beam (EB) crosslinking treatment of each mono-layer could also be fabricated. (author)

  15. Experimental Study of the Flexural and Compression Performance of an Innovative Pultruded Glass-Fiber-Reinforced Polymer-Wood Composite Profile.

    Science.gov (United States)

    Qi, Yujun; Xiong, Wei; Liu, Weiqing; Fang, Hai; Lu, Weidong

    2015-01-01

    The plate of a pultruded fiber-reinforced polymer or fiber-reinforced plastic (FRP) profile produced via a pultrusion process is likely to undergo local buckling and cracking along the fiber direction under an external load. In this study, we constructed a pultruded glass-fiber-reinforced polymer-light wood composite (PGWC) profile to explore its mechanical performance. A rectangular cross-sectional PGWC profile was fabricated with a paulownia wood core, alkali-free glass fiber filaments, and unsaturated phthalate resin. Three-point bending and short column axial compression tests were conducted. Then, the stress calculation for the PGWC profile in the bending and axial compression tests was performed using the Timoshenko beam theory and the composite component analysis method to derive the flexural and axial compression rigidity of the profile during the elastic stress stage. The flexural capacity for this type of PGWC profile is 3.3-fold the sum of the flexural capacities of the wood core and the glass-fiber-reinforced polymer (GFRP) shell. The equivalent flexural rigidity is 1.5-fold the summed flexural rigidity of the wood core and GFRP shell. The maximum axial compressive bearing capacity for this type of PGWC profile can reach 1.79-fold the sum of those of the wood core and GFRP shell, and its elastic flexural rigidity is 1.2-fold the sum of their rigidities. These results indicate that in PGWC profiles, GFRP and wood materials have a positive combined effect. This study produced a pultruded composite material product with excellent mechanical performance for application in structures that require a large bearing capacity.

  16. Experimental Study of the Flexural and Compression Performance of an Innovative Pultruded Glass-Fiber-Reinforced Polymer-Wood Composite Profile.

    Directory of Open Access Journals (Sweden)

    Yujun Qi

    Full Text Available The plate of a pultruded fiber-reinforced polymer or fiber-reinforced plastic (FRP profile produced via a pultrusion process is likely to undergo local buckling and cracking along the fiber direction under an external load. In this study, we constructed a pultruded glass-fiber-reinforced polymer-light wood composite (PGWC profile to explore its mechanical performance. A rectangular cross-sectional PGWC profile was fabricated with a paulownia wood core, alkali-free glass fiber filaments, and unsaturated phthalate resin. Three-point bending and short column axial compression tests were conducted. Then, the stress calculation for the PGWC profile in the bending and axial compression tests was performed using the Timoshenko beam theory and the composite component analysis method to derive the flexural and axial compression rigidity of the profile during the elastic stress stage. The flexural capacity for this type of PGWC profile is 3.3-fold the sum of the flexural capacities of the wood core and the glass-fiber-reinforced polymer (GFRP shell. The equivalent flexural rigidity is 1.5-fold the summed flexural rigidity of the wood core and GFRP shell. The maximum axial compressive bearing capacity for this type of PGWC profile can reach 1.79-fold the sum of those of the wood core and GFRP shell, and its elastic flexural rigidity is 1.2-fold the sum of their rigidities. These results indicate that in PGWC profiles, GFRP and wood materials have a positive combined effect. This study produced a pultruded composite material product with excellent mechanical performance for application in structures that require a large bearing capacity.

  17. Experimental Study of the Flexural and Compression Performance of an Innovative Pultruded Glass-Fiber-Reinforced Polymer-Wood Composite Profile

    Science.gov (United States)

    Qi, Yujun; Xiong, Wei; Liu, Weiqing; Fang, Hai; Lu, Weidong

    2015-01-01

    The plate of a pultruded fiber-reinforced polymer or fiber-reinforced plastic (FRP) profile produced via a pultrusion process is likely to undergo local buckling and cracking along the fiber direction under an external load. In this study, we constructed a pultruded glass-fiber-reinforced polymer-light wood composite (PGWC) profile to explore its mechanical performance. A rectangular cross-sectional PGWC profile was fabricated with a paulownia wood core, alkali-free glass fiber filaments, and unsaturated phthalate resin. Three-point bending and short column axial compression tests were conducted. Then, the stress calculation for the PGWC profile in the bending and axial compression tests was performed using the Timoshenko beam theory and the composite component analysis method to derive the flexural and axial compression rigidity of the profile during the elastic stress stage. The flexural capacity for this type of PGWC profile is 3.3-fold the sum of the flexural capacities of the wood core and the glass-fiber-reinforced polymer (GFRP) shell. The equivalent flexural rigidity is 1.5-fold the summed flexural rigidity of the wood core and GFRP shell. The maximum axial compressive bearing capacity for this type of PGWC profile can reach 1.79-fold the sum of those of the wood core and GFRP shell, and its elastic flexural rigidity is 1.2-fold the sum of their rigidities. These results indicate that in PGWC profiles, GFRP and wood materials have a positive combined effect. This study produced a pultruded composite material product with excellent mechanical performance for application in structures that require a large bearing capacity. PMID:26485431

  18. Fundamental study of a refractory-based carbon fiber reinforced composite made by reactive melt infiltration for hypersonic applications

    Science.gov (United States)

    Wali, Natalie Alice

    Ceramic matrix composites are excellent candidates for ultrahigh temperature applications due their good physical properties, which are a combination of a chemically stable matrix and tough fiber reinforcement. This work is a fundamental study of a carbon fiber reinforced zirconium carbide composite (Cf/ZrC). The background chapter reviews reactive melt infiltration, which is the processing method used to make the Cf/ZrC composite. The first chapter discusses the microstructural characterization and development of Cf/ZrC. A formation mechanism of the unique matrix microstructure is proposed based on the characterization results. In the second chapter the mechanical properties of Cf/ZrC were determined. The fracture toughness at room temperature is obtained with a standard four point bend test, while flexural strength of Cf/ZrC is obtained to the ultra high temperature regime. For high temperatures a testing rig was modified to operate in inert atmosphere and tests were conducted at 1100 °C, 1350 °C and 1650 °C. Correlation is made between the flexural strength and fiber coatings of two different composite types. In situ compression tests were performed a modified SEM. Digital image correlation was used to monitor strains during compression. The stress-strain information is correlated to surface deformation. The environmental durability and oxidation behavior of Cf/ZrC and ZrC is detailed in the third and fourth chapters. The oxidation and shock behavior of Cf/ZrC were observed under both slow and rapid heating rates to ultra high temperatures. For rapid heating rates a panel was subjected to heating at steady-state and non-steady state heat flux. For slow heating rates specimen coupons were heated at 2000 °C in a bottom-loading furnace. Specimens were characterized post-test by x-ray diffraction, electron microscopy, electron probe microanalysis, and optical microscopy. The oxidation kinetics of Cf/ZrC composites and ZrC powders (45 micron and 60 nanometer

  19. Investigations of the mechanical properties of bi-layer and trilayer fiber reinforced composites

    Science.gov (United States)

    Jayakrishna, K.; Balasubramani, K.; Sultan, M. T. H.; Karthikeyan, S.

    2016-10-01

    Natural fibers are renewable raw materials with an environmental-friendly properties and they are recyclable. The mechanical properties of bi-layer and tri-layer thermoset polymer composites have been analyzed. The bi-layer composite consists of basalt and jute mats, while the tri-layer composite consists of basalt fiber, jute fiber and glass fiber mats. In both cases, the epoxy resin was used as the matrix and PTFE as a filler in the composites. The developed trilayer natural fiber composite can be used in various industrial applications such as automobile parts, construction and manufacturing. Furthermore, it also can be adopted in aircraft interior decoration and designed body parts. Flexural, impact, tensile, compression, shear and hardness tests, together with density measurement, were conducted to study the mechanical properties of both bi-layer and tri-layer composites. From the comparison, the tri-layer composite was found to perform in a better way in all tests.

  20. Numerical simulating and experimental study on the woven carbon fiber-reinforced composite laminates under low-velocity impact

    Science.gov (United States)

    Liu, Hanyang; Tang, Zhanwen; Pan, Lingying; Zhao, Weidong; Sun, Baogang; Jiang, Wenge

    2016-05-01

    Impact damage has been identified as a critical form of the defects that constantly threatened the reliability of composite structures, such as those used in the aerospace structures and systems. Low energy impacts can introduce barely visible damage and cause the degradation of structural stiffness, furthermore, the flaws caused by low-velocity impact are so dangerous that they can give rise to the further extended delaminations. In order to improve the reliability and load carrying capacity of composite laminates under low-velocity impact, in this paper, the numerical simulatings and experimental studies on the woven fiber-reinforced composite laminates under low-velocity impact with impact energy 16.7J were discussed. The low velocity impact experiment was carried out through drop-weight system as the reason of inertia effect. A numerical progressive damage model was provided, in which the damages of fiber, matrix and interlamina were considered by VUMT subroutine in ABAQUS, to determine the damage modes. The Hashin failure criteria were improved to cover the failure modes of fiber failure in the directions of warp/weft and delaminations. The results of Finite Element Analysis (FEA) were compared with the experimental results of nondestructive examination including the results of ultrasonic C-scan, cross-section stereomicroscope and contact force - time history curves. It is found that the response of laminates under low-velocity impact could be divided into stages with different damage. Before the max-deformation of the laminates occurring, the matrix cracking, fiber breakage and delaminations were simulated during the impactor dropping. During the releasing and rebounding period, matrix cracking and delaminations areas kept increasing in the laminates because of the stress releasing of laminates. Finally, the simulating results showed the good agreements with the results of experiment.

  1. Effect of Coconut Fillers on Hybrid Coconut Kevlar Fiber Reinforced Epoxy Composites

    Directory of Open Access Journals (Sweden)

    S. P. Jani

    2015-12-01

    Full Text Available This project focuses on the conversion of naturally available coconut fibers and shells into a useful composite. In addition to it, some mechanical properties of the resultant composite is determined and also the effect of coconut shell fillers on the composite is also investigated. The few portion of the composite is incorporated with synthetic Kevlar fiber, thus the coconut fiber is hybridized to enhance the mechanical properties of coconut. In this work two types of composite is fabricate, kevelar coconut fibre (kc composite and kevelarcoco nut fibre coconut shell filler (kccsf composite. Coconut fibers have low weight and considerable properties among the natural fibers, while coconut fillers have a good ductile and impact property. The natural fibers and fillers are treated with Na-OH to make it free of organic impurities. Epoxy resin is used as the polymer matrix. Two composite are produced one with fillers and the other without the fillers using compression molding method. Mechanical properties like tensile strength, flexural strength and water absorption tests are done with ASTM standard. It is observed that that the addition of filler materials improves the adhesiveness of the fibers leading to the increase in the above mentioned properties. The density of the composite is also low hence the strength to weight ratio is very high. The water absorption test also showed that the resultant composite had a small adhesion to water and absorption of water.

  2. Effect of Short Fiber Reinforcement on Mechanical Properties of Hybrid Phenolic Composites

    Directory of Open Access Journals (Sweden)

    Sembian Manoharan

    2014-01-01

    Full Text Available Fiber plays an important role in determining the hardness, strength, and dynamic mechanical properties of composite material. In the present work, enhancement of viscoelastic behaviour of hybrid phenolic composites has been synergistically investigated. Five different phenolic composites, namely, C1, C2, C3, C4, and C5, were fabricated by varying the weight percentage of basalt and aramid fiber, namely, 25, 20, 15, 10, and 5% by compensating with barium sulphate (BaSO4 to keep the combined reinforcement concentration at 25 wt%. Hardness was measured to examine the resistance of composites to indentation. The hardness of phenolic composites increased from 72.2 to 85.2 with increase in basalt fiber loading. Composite C1 (25 wt% fiber is 1.2 times harder than composite C5. Compression test was conducted to find out compressive strength of phenolic composites and compressive strength increased with increase in fiber content. Dynamic mechanical analysis (DMA was carried out to assess the temperature dependence mechanical properties in terms of storage modulus (E′, loss modulus (E′′, and damping factor (tan δ. The results indicate great improvement of E′ values and decrease in damping behaviour of composite upon fiber addition. Further X-ray powder diffraction (XRD and energy-dispersive X-ray (EDX analysis were employed to characterize the friction composites.

  3. Mechanical and Chemical Properties of Bamboo/Glass Fibers Reinforced Polyester Composites

    Directory of Open Access Journals (Sweden)

    K.Sudha Madhuri,

    2016-01-01

    Full Text Available The chemical resistance of Bamboo/Glass reinforced Polyester hybrid composites to acetic acid, Nitric acid, Hydrochloric acid, Sodium hydroxide, Sodium carbonate, Benzene, Toluene, Carbon tetrachloride and Water was studied. The tensile and impact properties of these composites were also studied. The effect of alkali treatment of bamboo fibers on these properties was studied. It was observed that the tensile and impact properties of the hybrid composites increase with glass fiber content. The author investigated the interfacial bonding between Glsss/Bamboo fiber composites by SEM. These properties found to be higher when alkali treated bamboo fibers were used in hybrid composites. The hybrid fiber composites showed better resistance to the chemicals mentioned above. The elimination of amorphous hemi-cellulose with alkali treatment leading to higher crystallinity of the bamboo fibers with alkali treatment may be responsible for these observations.

  4. Investigation on Mechanical Properties of Coir Fiber Reinforced Polymer Resin Composites Saturated with Different Filling Agents

    Science.gov (United States)

    Nallusamy, S.; Suganthini Rekha, R.; Karthikeyan, A.

    2017-08-01

    The main objective of this research article is to assess the mechanical properties and fracture analysis of bone and sea shell powders independently integrated with coir fiber polymer composites. The specimen was fabricated with coir fiber at various dimensions of coir fiber like diameter, length, content and mesh size of the powder. Tensile, compressive, flexural and impact tests were conducted in the prepared composite materials as per the techniques of ASTM standard. The fracture faces were explored with the help of SEM images. From the final results it was concluded that the sea shell powder composite provides good tensile and flexural strength than bone powder composite, while bone powder composite material gives good compressive and impact strength than sea shell powder composite material.

  5. Properties and Microstructure of Polymer Emulsions Modified Fibers Reinforced Cementitious Composites

    Institute of Scientific and Technical Information of China (English)

    WU Ying; SUN Qianyao; KONG Lian; FANG He

    2014-01-01

    The synthesis and characterization of a new class of cementitious composites filled with polymer emulsions were investigated, and their superior mechanical strength and durability properties compared to composites devoid of fillers were reported. Polymer emulsions were utilized to mechanically reinforce the composite and bridge the cement, fly ash, aggregate and fibers. The results reveal that the epoxy emulsion and poly (ethylene-co-vinyl acetate) emulsion markedly enhance the mechanical and durability properties of cemetitious composites. The fibers can be pulled out in the form of slip-hardening and the abrasion phenomenon can be observed clearly on the surface of the fibers. The hydration extent of cement is higher than that of the pristine composites. The polymer modified cementitious composites designed on micromechanics, have flexibility and plasticity which could be applied for a novel form of multifunctional materials with a range of pipeline coatings applications.

  6. Stochastic Simulation of Progressive Fiber Breaking in Longitudinally Fiber-Reinforced Composites

    OpenAIRE

    Wu,Yi

    2012-01-01

    Statistics has a wide application in science and engineering fields. This research work is aim to study the progressive fiber breaking evolution in the longitudinally reinforced composites from a statistical perspective. First of all, the fiber breaking evolution in a single fiber composite is studied. The Kolmogorov-Smirnov goodness-of-fit test is performed on the experimental data to characterize the damage pattern of the fiber in a single fiber composite. The results indicate that the frag...

  7. Sound Absorption Properties Of Single-Hole Hollow Polyester Fiber Reinforced Hydrogenated Carboxyl Nitrile Rubber Composites

    Directory of Open Access Journals (Sweden)

    Jie Hong

    2017-09-01

    Full Text Available A series of single-hole hollow polyester fiber (SHHPF reinforced hydrogenated carboxyl nitrile rubber (HXNBR composites were fabricated. In this study, the sound absorption property of the HXNBR/SHHPF composite was tested in an impedance tube, the composite morphology was characterized by scanning electron microscope (SEM, and the tensile mechanical property was measured by strength tester. The results demonstrated that a remarkable change in sound absorption can be observed by increasing the SHHPF content from 0% to 40%. In the composite with 40% SHHPF in 1 mm thickness, the sound absorption coefficient reached 0.671 at 2,500 Hz; the effective bandwidth was 1,800-2,500 Hz for sound absorption coefficient larger than 0.2. But the sound absorption property of the composite deteriorated when the SHHPF content increased to 50% in 1 mm thickness. While with 20% SHHPF proportion, the sound absorption property was improved by increasing the thickness of composites from 1 to 5 mm. Compared with the pure HXNBR of the same thickness, the tensile mechanical property of the composite improved significantly by increasing the SHHPF proportion. As a lightweight composite with excellent sound absorption property, the HXNBR/SHHPF composite has potential practical application value in the fields of engineering.

  8. Influence of moisture absorption on properties of fiber reinforced polyamide 6 composites

    DEFF Research Database (Denmark)

    Raghavalu Thirumalai, Durai Prabhakaran; Løgstrup Andersen, Tom; Lystrup, Aage

    2011-01-01

    A state-of-the art study of thermoplastic polymer matrix materials for fiber composites has identified polyamide 6 (PA6) as a potential candidate thermoplastic polymer relevant for manufacturing large composite structures like wind turbine blades. The mechanical properties of PA6 are highly...... sensitive to moisture, and if PA6 is used as matrix material in a fiber composite, the properties of the fiber composite will depend on the moisture content of the material. At standard condition (23 °C and 50% RH) polyamide6 absorbs about 3 weight-% of water, whereas the PA6 material is dry right after...

  9. A Review of Natural Fiber Reinforced Poly(Vinyl Alcohol Based Composites: Application and Opportunity

    Directory of Open Access Journals (Sweden)

    Boon Khoon Tan

    2015-11-01

    Full Text Available Natural fibers are fine examples of renewable resources that play an important role in the composites industry, which produces superior strength comparable to synthetic fibers. Poly(vinyl alcohol (PVA composites in particular have attracted enormous interest in view of their satisfactory performance, properties and biodegradability. Their performance in many applications such as consumer, biomedical, and agriculture is well defined and promising. This paper reviews the utilization of natural fibers from macro to nanoscale as reinforcement in PVA composites. An overview on the properties, processing methods, biodegradability, and applications of these composites is presented. The advantages arising from chemical and physical modifications of fibers or composites are discussed in terms of improved properties and performance. In addition, proper arrangement of nanocellulose in composites helps to prevent agglomeration and results in a better dispersion. The limitations and challenges of the composites and future works of these bio-composites are also discussed. This review concludes that PVA composites have potential for use in numerous applications. However, issues on technological feasibility, environmental effectiveness, and economic affordability should be considered.

  10. Dynamic mechanical and dielectric behavior of banana–glass hybrid fiber reinforced polyester composites.

    CSIR Research Space (South Africa)

    Pothan, LA

    2009-01-01

    Full Text Available of the two fibers on the ultimate viscoelastic behavior of the composites are also investigated. Composites are prepared with banana as the surface layer and glass as the surface layer and also as an intimate mixture of glass and banana. At temperatures above...

  11. Microstructure and mechanical behavior of metallic glass fiber-reinforced Al alloy matrix composites.

    Science.gov (United States)

    Wang, Z; Georgarakis, K; Nakayama, K S; Li, Y; Tsarkov, A A; Xie, G; Dudina, D; Louzguine-Luzgin, D V; Yavari, A R

    2016-04-12

    Metallic glass-reinforced metal matrix composites are an emerging class of composite materials. The metallic nature and the high mechanical strength of the reinforcing phase offers unique possibilities for improving the engineering performance of composites. Understanding the structure at the amorphous/crystalline interfaces and the deformation behavior of these composites is of vital importance for their further development and potential application. In the present work, Zr-based metallic glass fibers have been introduced in Al7075 alloy (Al-Zn-Mg-Cu) matrices using spark plasma sintering (SPS) producing composites with low porosity. The addition of metallic glass reinforcements in the Al-based matrix significantly improves the mechanical behavior of the composites in compression. High-resolution TEM observations at the interface reveal the formation of a thin interdiffusion layer able to provide good bonding between the reinforcing phase and the Al-based matrix. The deformation behavior of the composites was studied, indicating that local plastic deformation occurred in the matrix near the glassy reinforcements followed by the initiation and propagation of cracks mainly through the matrix. The reinforcing phase is seen to inhibit the plastic deformation and retard the crack propagation. The findings offer new insights into the mechanical behavior of metal matrix composites reinforced with metallic glasses.

  12. Effect of Rare Earths on Tribological Properties of Carbon Fibers Reinforced PTFE Composites

    Institute of Scientific and Technical Information of China (English)

    Shangguan Qianqian; Cheng Xianhua

    2007-01-01

    Carbon fibers (CF) were surface treated with air-oxidation and rare earths (RE), respectively. The effect of RE surface treatment on tensile strength and tribological properties of CF reinforced polytetrafluoroethylene (PTFE) composites was investigated. Experimental results revealed that RE was superior to air oxidation in improving the tensile strength, elongation, and the tensile modulus of CF reinforced PTFE (CF/PTFE) composite. Compared to the untreated and air-oxidated CF/PTFE composite, the RE treated composite had the lowest friction coefficient and specific wear rate under a given applied load and reciprocating sliding frequency. The RE treatment effectively improved the interfacial adhesion between CF and PTFE. With strong interfacial coupling, the carbon fibers carried most of the load, and direct contact and adhesion between PTFE and the counterpart were reduced, accordingly the friction and wear properties of the composite were improved.

  13. Mechanical properties and in vivo performance of load-bearing fiber-reinforced composite intramedullary nails with improved torsional strength.

    Science.gov (United States)

    Moritz, N; Strandberg, N; Zhao, D S; Mattila, R; Paracchini, L; Vallittu, P K; Aro, H T

    2014-12-01

    Fiber-reinforced composites (FRC) could be feasible materials for fracture fixation devices if the mechanical properties of the composites are congruent with the local structural properties of bone. In a recently developed FRC implant, bisphenol A dimethacrylate (BisGMA) and triethylene glycol dimethacrylate (TEGDMA) resin was reinforced with unidirectional E-glass fibers. The addition of a braided glass fiber sleeving to the unidirectional fibers increased the torsional strength (99.5MPa) of the FRC implants at the expense of the flexural strength (602.0MPa). The flexural modulus was 15.3GPa. Two types of FRC intramedullary nails were prepared; first type was FRC as such, second type was FRC with a surface layer of bioactive glass (BG) granules. Experimental oblong subtrochanteric defect was created in 14 rabbits. The defect, which reduced the torsional strength of the bones by 66%, was fixed with an FRC intramedullary nail of either type. The contralateral intact femur served as the control. This model simulated surgical stabilization of bone metastasis. After 12 weeks of follow-up, the femurs were harvested and analyzed by torsional testing, micro-CT and hard tissue histology. Healed undisplaced peri-implant fractures were noticed in half of the animals irrespective of the type of FRC implant. Torsional testing showed no significant differences between the implantation groups. The torsional strength of the bones stabilized by either type of FRC implant was 83% of that of the contralateral femurs. In histological analysis, no implant debris and no adverse tissue reactions were observed. While the mechanical properties of the modified FRCs were suboptimal, the FRC intramedullary nails supported the femurs without structural failure, even in the cases of peri-implant fractures.

  14. Root canal filling: fracture strength of fiber-reinforced composite-restored roots and finite element analysis.

    Science.gov (United States)

    Rippe, Marília Pivetta; Santini, Manuela Favarin; Bier, Carlos Alexandre Souza; Borges, Alexandre Luiz Souto; Valandro, Luiz Felipe

    2013-01-01

    The aims of this study were to evaluate the effect of root canal filling techniques on root fracture resistance and to analyze, by finite element analysis (FEA), the expansion of the endodontic sealer in two different root canal techniques. Thirty single-rooted human teeth were instrumented with rotary files to a standardized working length of 14 mm. The specimens were embedded in acrylic resin using plastic cylinders as molds, and allocated into 3 groups (n=10): G(lateral) - lateral condensation; G(single-cone) - single cone; G(tagger) - Tagger's hybrid technique. The root canals were prepared to a length of 11 mm with the #3 preparation bur of a tapered glass fiber-reinforced composite post system. All roots received glass fiber posts, which were adhesively cemented and a composite resin core was built. All groups were subjected to a fracture strength test (1 mm/min, 45°). Data were analyzed statistically by one-way ANOVA with a significance level of 5%. FEA was performed using two models: one simulated lateral condensation and Tagger's hybrid technique, and the other one simulated the single-cone technique. The second model was designed with an amount of gutta-percha two times smaller and a sealer layer two times thicker than the first model. The results were analyzed using von Mises stress criteria. One-way ANOVA indicated that the root canal filling technique affected the fracture strength (p=0.004). The G(lateral) and G(tagger) produced similar fracture strength values, while G(single-cone) showed the lowest values. The FEA showed that the single-cone model generated higher stress in the root canal walls. Sealer thickness seems to influence the fracture strength of restored endodontically treated teeth.

  15. Flexible fiber-reinforced composites with improved interfacial adhesion by mussel-inspired polydopamine and poly(methyl methacrylate) coating.

    Science.gov (United States)

    Yi, Mi; Sun, Hongyang; Zhang, Hongcheng; Deng, Xuliang; Cai, Qing; Yang, Xiaoping

    2016-01-01

    To obtain a kind of light-curable fiber-reinforced composite for dental restoration, an excellent interfacial adhesion between the fiber and the acrylate resin matrix is quite essential. Herein, surface modification on glass fibers were carried out by coating them with poly(methyl methacrylate) (PMMA), polydopamine (PDA), or both. The PMMA or PDA coating was performed by soaking fibers in PMMA/acetone solution or dopamine aqueous solution. PDA/PMMA co-coated glass fibers were obtained by further soaking PDA-coated fibers in PMMA/acetone solution. These modified fibers were impregnated with bisphenol A glycidyl methacrylate (Bis-GMA)/triethylene glycol dimethacrylate (TEGDMA) (5:5, w/w) dental resin at a volume fraction of 75%, using unmodified fibers as reference. Light-cured specimens were submitted to evaluations including flexural properties, morphological observation, dynamic mechanical thermal analysis (DMTA) and pull-out test. In comparison with unmodified glass fibers, all the modified glass fibers showed enhancements in flexural strength and modulus of Bis-GMA/TEGDMA resin composites. Results of DMTA and pull-out tests confirmed that surface modification had significantly improved the interfacial adhesion between the glass fiber and the resin matrix. Particularly, the PDA/PMMA co-coated glass fibers displayed the most efficient reinforcement and the strongest interfacial adhesion due to the synergetic effects of PDA and PMMA. It indicated that co-coating method was a promising approach in modifying the interfacial compatibility between inorganic glass fiber and organic resin matrix. Copyright © 2015 Elsevier B.V. All rights reserved.

  16. In vitro evaluation of fracture resistance of Fiber-Reinforced Composite inlay bridges in upper anterior and lower posterior teeth

    Directory of Open Access Journals (Sweden)

    Jalalian E.

    2007-07-01

    Full Text Available Background and Aim: Considering flexural strength of fiber-reinforced composites (FRC and also the role of conservative cavities in protecting sound tissue of abutments, the aim of this study was to evaluate the fracture resistance of these bridges by handmade samples in vitro.Materials and Methods: In this experimental in vitro study, 44 sound newly extracted teeth were used to make 22 fixed inlay bridges including 11 three unit anterior upper inlay bridges substituting clinical model of upper central and 11 three unit posterior lower inlay bridges substituting clinical model of lower first molar. Specimens were prepared with FRC and mounted with artificial PDL in acryl. Cases were exposed to final load by using Universal Testing Machine (Instron 1195 with the speed of 1 mm/min. Statistical analysis was performed by Kolmogorov- Smirnov, independent sample T and Kaplan-Meier tests with p<0.05 as the level of significance.Results: Based on the statistical tests, the 95% confidence interval of mean was 450-562 N in anterior and  1473- 1761 N in posterior area. Fracture strength was high in the studied groups. Fractures in both groups occurred on composite facing, and the framework remained intact. The highest percentage of fracture in posterior teeth was in the middle of pontic towards the distal connector and in the anterior teeth in the lateral connector, between central pontic and lateral abutment. Using the independent sample T  test a significant statistical difference was observed between two groups (P<0.001. The fracture resistance of anterior samples was lower than the posterior ones.Conclusion: Based on the results of this study regarding the high fracture resistance in both areas FRC inlay bridges could be recommended for upper anterior and lower posterior teeth in clinical dentistry certainly more studies are needed to ascertain this treatment option.

  17. Investigations on Thermal Conductivities of Jute and Banana Fiber Reinforced Epoxy Composites

    Science.gov (United States)

    Pujari, Satish; Ramakrishna, Avasarala; Balaram Padal, Korabu Tulasi

    2017-04-01

    The Jute and Banana fibers are used as reinforcement in epoxy resin matrix for making partially green biodegradable material composite via hand lay-up technique. The thermal conductivity of the jute fiber epoxy composites and banana fiber epoxy composites at different volume fraction of the fiber is determined experimentally by using guarded heat flow meter method. The experimental results had shown that thermal conductivity of the composites decrease with an increase in the fiber content. Experimental results are compared with theoretical models (Series model, Hashin model and Maxwell model) to describe the variation of the thermal conductivity versus the volume fraction of the fiber. Good agreement between theoretical and experimental results is observed. Thermal conductivity of Banana fiber composite is less when compared to that of Jute composite which indicates banana is a good insulator and also the developed composites can be used as insulating materials in building, automotive industry and in steam pipes to save energy by reducing rate of heat transfer.

  18. Investigations on Thermal Conductivities of Jute and Banana Fiber Reinforced Epoxy Composites

    Science.gov (United States)

    Pujari, Satish; Ramakrishna, Avasarala; Balaram Padal, Korabu Tulasi

    2016-01-01

    The Jute and Banana fibers are used as reinforcement in epoxy resin matrix for making partially green biodegradable material composite via hand lay-up technique. The thermal conductivity of the jute fiber epoxy composites and banana fiber epoxy composites at different volume fraction of the fiber is determined experimentally by using guarded heat flow meter method. The experimental results had shown that thermal conductivity of the composites decrease with an increase in the fiber content. Experimental results are compared with theoretical models (Series model, Hashin model and Maxwell model) to describe the variation of the thermal conductivity versus the volume fraction of the fiber. Good agreement between theoretical and experimental results is observed. Thermal conductivity of Banana fiber composite is less when compared to that of Jute composite which indicates banana is a good insulator and also the developed composites can be used as insulating materials in building, automotive industry and in steam pipes to save energy by reducing rate of heat transfer.

  19. Effect of the surface roughness on interfacial properties of carbon fibers reinforced epoxy resin composites

    Energy Technology Data Exchange (ETDEWEB)

    Song Wei [College of Chemistry, Chemical Engineering and Materials Science, Department of Materials Science and Engineering, Soochow University, Suzhou, Jiangsu 215123 (China); Gu Aijuan, E-mail: ajgu@suda.edu.cn [College of Chemistry, Chemical Engineering and Materials Science, Department of Materials Science and Engineering, Soochow University, Suzhou, Jiangsu 215123 (China); Liang Guozheng, E-mail: lgzheng@suda.edu.cn [College of Chemistry, Chemical Engineering and Materials Science, Department of Materials Science and Engineering, Soochow University, Suzhou, Jiangsu 215123 (China); Yuan Li [College of Chemistry, Chemical Engineering and Materials Science, Department of Materials Science and Engineering, Soochow University, Suzhou, Jiangsu 215123 (China)

    2011-02-15

    The effect of the surface roughness on interfacial properties of carbon fibers (CFs) reinforced epoxy (EP) resin composite is studied. Aqueous ammonia was applied to modify the surfaces of CFs. The morphologies and chemical compositions of original CFs and treated CFs (a-CFs) were characterized by Atomic Force Microscopy (AFM), and X-ray Photoelectron Spectroscopy (XPS). Compared with the smooth surface of original CF, the surface of a-CF has bigger roughness; moreover, the roughness increases with the increase of the treating time. On the other hand, no obvious change in chemical composition takes place, indicating that the treating mechanism of CFs by aqueous ammonia is to physically change the morphologies rather than chemical compositions. In order to investigate the effect of surface roughness on the interfacial properties of CF/EP composites, the wettability and Interfacial Shear Strength (IFSS) were measured. Results show that with the increase of the roughness, the wettabilities of CFs against both water and ethylene glycol improves; in addition, the IFSS value of composites also increases. These attractive phenomena prove that the surface roughness of CFs can effectively overcome the poor interfacial adhesions between CFs and organic matrix, and thus make it possible to fabricate advanced composites based on CFs.

  20. Theoretical and Experimental Researches of Post-microbuckling for Fiber-reinforced Composites

    Institute of Scientific and Technical Information of China (English)

    魏悦广; 杨卫; 黄克智

    1994-01-01

    Post-microbuckling is a fundamental feature of compressive failure process for the unidirectional-liber-reinforced composites and laminated composites. The post-microbuckling behavior of composites under compression in the light of the Kevlar49-reinforced 648/BF3.400 (brittle epoxy) and EP (flexible epoxy) is studied, theoretically and experimentally. Analytical results of compressive strength are in good agreement with experimental results, qualitatively and quantitatively. By the experimental research, the post-microbuckling feature of the advancing kink band model is dearly displayed.

  1. A Randomly Enlarging Critical Core Theory of Unidirectionally Fiber-reinforced Composites

    Institute of Scientific and Technical Information of China (English)

    范赋群; 曾庆敦

    1994-01-01

    Based upon the micro-stochastic failure mechanisms of composites,a new micromechanical statistical model,i.e.randomly enlarging critical core theory,for the tensile failure of unidirectional composites is proposed,with which we can overcome the primary imperfections of the existing chain-of-bundles probability model.On the basis of the established statistical model,the strength distribution and the failure criterion of composites are derived.The predictions of strength for T300/5208 and glass/epoxy show very good agreement with the existing experimental results,thus verifying the reasonableness and correctness of the present theory.

  2. EFFECT OF SURFACE TREATMENT ON THE MECHANICAL PROPERTIES OF BAGASSE FIBER REINFORCED POLYMER COMPOSITE

    Directory of Open Access Journals (Sweden)

    Samir Kumar Acharya

    2011-06-01

    Full Text Available Bagasse is a by-product of the sugarcane milling process, and it also is an important fuel resource for that industry. In this study an attempt has been made to utilize this by-product to prepare a composite using epoxy resin. The fibers surface was modified by alkali treatment with 5% NaOH solution for 0, 2, 4 and 6 hrs. The effect of fiber surface modification on the mechanical properties such as flexural strength of the composites was investigated with the fibers as received from the milling process. It was found that alkali-treated bagasse/epoxy composites significantly improved the flexural strength of the composite. An SEM investigation also indicated that the surface modifications improved the fiber–matrix interaction.

  3. High-Strength and Optically Transparent Fiber-Reinforced Composites Project

    Data.gov (United States)

    National Aeronautics and Space Administration — For many applications there exists a need for mechanically strong composite materials of high optical quality and transparency equivalent to window glass. One method...

  4. Multiscale modeling of microscale fiber reinforced composites with nano-engineered interphases

    CERN Document Server

    Kundalwalal, S I; Wardle, B L

    2015-01-01

    This study is focused on the mechanical properties and stress transfer behavior of multiscale composite containing nano- and micro-scale fillers. A novel concept has been proposed to exploit the remarkable mechanical properties of carbon nanotubes (CNTs) to improve the stress transfer through the interphases, enabling their additional functionalities not available otherwise at the microscale. The distinctive feature of construction of this composite is such that CNTs are dispersed around the microscale fiber to modify fiber-matrix interfacial adhesion. Accordingly, models are developed for hybrid composites. First, molecular dynamics simulations in conjunction with the Mori-Tanaka method are used to determine the effective elastic properties of nano-engineered interphase layer comprised of CNT bundles and epoxy. Subsequently, a micromechanical pull-out model is developed for the resulting multiscale composite and its stress transfer behavior is studied for different orientations of CNT bundles. The current pu...

  5. Mechanical properties and failure mechanisms of carbon fiber reinforced epoxy laminated composites

    Energy Technology Data Exchange (ETDEWEB)

    Thissell, W.R.; Zurek, A.K.; Addessio, F.

    1995-09-01

    The mechanical behavior of quasi-isotropic and unidirectional epoxy-matrix carbon-fiber laminated composites subjected compressive loading at strain rates of 10{sup {minus}3} and 2000 s{sup {minus}1} are described. Failure in the studied composites was dominated by delamination which proceeded by brittle fracture of the epoxy-matrix. The matrix-fiber bonding in these composites is very strong and prevented the occurrence of significant fiber-pullout. The mode I delamination strain energy release rate of the unidirectional composites was determined using the double cantilever beam and hole in plate compression method. The DCB method indicated a significant R curve effect attributed to fiber bridging while the presently available hole in plate analytical methods show questionable validity for highly anisotropic materials.

  6. Mechanical properties, microscopy, and failure mechanisms of carbon fiber reinforced epoxy laminated composites

    Energy Technology Data Exchange (ETDEWEB)

    Thissell, W.R.; Zurek, A.K.; Addessio, F.

    1995-12-31

    The mechanical behavior of quasi-isotropic and unidirectional epoxy- matrix carbon-fiber laminated composites subjected to compressive loading at strain rates of 10{sup {minus}3} and 2000 s{sup {minus}1} are described. Failure in the studied composites was dominated by delamination which proceeded by brittle fracture of the epoxy matrix. The matrix-fiber bonding in these composites is very strong and prevented the occurrence of significant fiber-pullout. The mode I delamination strain energy release rate of the unidirectional composites was determined using the double cantilever beam and hole in plate compression methods. The DCB method indicated a significant R curve effect attributed to fiber bridging while the presently available hole in plate analytical methods show questionable validity for highly anisotropic materials.

  7. Natural Mallow Fiber-Reinforced Epoxy Composite for Ballistic Armor Against Class III-A Ammunition

    Science.gov (United States)

    Nascimento, Lucio Fabio Cassiano; Holanda, Luane Isquerdo Ferreira; Louro, Luis Henrique Leme; Monteiro, Sergio Neves; Gomes, Alaelson Vieira; Lima, Édio Pereira

    2017-10-01

    Epoxy matrix composites reinforced with up to 30 vol pct of continuous and aligned natural mallow fibers were for the first time ballistic tested as personal armor against class III-A 9 mm FMJ ammunition. The ballistic efficiency of these composites was assessed by measuring the dissipated energy and residual velocity after the bullet perforation. The results were compared to those in similar tests of aramid fabric (Kevlar™) commonly used in vests for personal protections. Visual inspection and scanning electron microscopy analysis of impact-fractured samples revealed failure mechanisms associated with fiber pullout and rupture as well as epoxy cracking. As compared to Kevlar™, the mallow fiber composite displayed practically the same ballistic efficiency. However, there is a reduction in both weight and cost, which makes the mallow fiber composites a promising material for personal ballistic protection.

  8. Optimization and Static Stress Analysis of Hybrid Fiber Reinforced Composite Leaf Spring

    OpenAIRE

    Luay Muhammed Ali Ismaeel

    2015-01-01

    A monofiber reinforced composite leaf spring is proposed as an alternative to the typical steel one as it is characterized by high strength-to-weight ratio. Different reinforcing schemes are suggested to fabricate the leaf spring. The composite and the typical steel leaf springs are subjected to the same working conditions. A weight saving of about more than 60% can be achieved while maintaining the strength for the structures under consideration. The objective of the present study was to rep...

  9. Input-output characterization of fiber reinforced composites by P waves

    Science.gov (United States)

    Renneisen, John D.; Williams, James H., Jr.

    1990-01-01

    Input-output characterization of fiber composites is studied theoretically by tracing P waves in the media. A new path motion to aid in the tracing of P and the reflection generated SV wave paths in the continuum plate is developed. A theoretical output voltage from the receiving transducer is calculated for a tone burst. The study enhances the quantitative and qualitative understanding of the nondestructive evaluation of fiber composites which can be modeled as transversely isotropic media.

  10. Point of Impact Prediction in Anisotropic Fiber Reinforced Composite Plates from the Acoustic Emission Data

    Science.gov (United States)

    Kundu, T.; Das, S.; Jata, K. V.

    2008-02-01

    A newly developed optimization based method is followed to locate the point of impact in anisotropic composite plates for which conventional triangulation technique fails. The new technique works for both anisotropic and isotropic plates. Experiments are carried out by dropping a steel ball on a graphite-epoxy composite plate and picking up acoustic signals by passive transducers adhesively bonded to the plate at different locations. Predicted points of impact are compared with the true impact point.

  11. Kenaf-glass fiber reinforced unsaturated polyester hybrid composites: Tensile properties

    Science.gov (United States)

    Zhafer, S. F.; Rozyanty, A. R.; Shahnaz, S. B. S.; Musa, L.; Zuliahani, A.

    2016-07-01

    The use of natural fibers in composite is rising in recent years due their lightweight, non-abrasive, combustible, non-toxic, low cost and biodegradable properties. However, in comparison with synthetic fibers, the mechanical properties of natural fibers are lower. Therefore, the inclusion of synthetic fibers could improve the mechanical performance of natural fiber based composites. In this study, kenaf bast fiber and glass fiber at different weight percentage loading were used as reinforcement to produce hybrid composites. Unsaturated polyester (UP) resin was used as matrix and hand lay-up process was performed to apply the UP resin on the hybrid kenaf bast/glass fiber composite. Effect of different fiber loading on tensile strength, tensile modulus and elongation at break of the hybrid composite was studied. It has been found that the highest value of tensile strength and modulus was achieved at 10 wt.% kenaf/10 wt.% glass fiber loading. It was concluded that addition of glass fiber has improved the tensile properties of kenaf bast fiber based UP composites.

  12. Smart Natural Fiber Reinforced Plastic (NFRP) Composites Based On Recycled Polypropylene in The Presence Kaolin

    Science.gov (United States)

    Suharty, N. S.; Ismail, H.; Diharjo, K.; Handayani, D. S.; Lestari, W. A.

    2017-07-01

    Composites contain double filler material which act as reinforcement and flame retardants of recycled polypropylene (rPP)/kaolin(Kao)/palm oil empty bunch fiber (PEBF) have been succesfully prepared. The composites were synthesized through reactively solution method, using coupling agent PP-g-AA and compatibilizer DVB. The effect of double filler [Kao/PEBF] were investigated flexural strength (FS), inflammability, and morphology. Mechanical testing result in accordance to ASTM D790, the FS of rPP/DVB/PP-g-AA/Kao+ZB/PEBF composite was 48% higher than that of rPP matrix. Moreover, flexural modulus (FM) was significantly improved by 56% as compared to that of rPP matrix. The scanning electron images (SEM) shown good dispersion of [Ka/PEBF] and good filler-matrix interaction. The inflammability testing result which is tested using ASTM D635, showed that the flame resistance of rPP/DVB/PP-g-AA/Kao+ZB/PEBF composite was improve by increasing of time to ignition (TTI) about 857% and burning rate (BR) decreasing to 66% compared to the raw material rPP matrix. In the same time, the addition of 20% (w/w) PEBF as a second filler to form rPP/DVB/PP-g-AA/Kao+ZB/PEBF composites (F5) is able to increase: the FS by 17.5%, the FM by 19%, the TTI by 7.6% and the BR by 3.7% compared to the composite without PEBF (F2).

  13. Numerical and experimental analysis on tensile properties of banana and glass fibers reinforced epoxy composites

    Indian Academy of Sciences (India)

    A SHADRACH JEYASEKARAN; K PALANI KUMAR; S RAJARAJAN

    2016-11-01

    In present day scenario, moving towards an environment friendly material is a key issue for manufacturing industries in order to provide suitable alternatives for the existing conventional materials. Natural fibers have higher economic impact and miniature in density when compared to glass fibers while making composites. Though the strength of natural fibers is not as high as glass fibers, their specific properties are comparable. In this paper a study has been carried out to find the tensile characteristics of hybrid composite made by intruding unidirectional banana and glass fibers into epoxy resin mixture. The hand lay-up method of fabrication was employed in preparing the composites of unidirectional glass fiber (UGF) and unidirectional banana/glass fiber (U B/G F). Tensile properties of the composites are verified using ANSYS. It is observed from the findings that the numerical analysis is found to be higher than experimental analysis. Hybridization of banana fiber shows better tensile properties. It is evident from the result that, comparatively equal displacement is obtained for the varying load for both the composites. The surface morphology of the tested composites is analyzed through scanning electron microscope (SEM).

  14. Experimental Test of Stainless Steel Wire Mesh and Aluminium Alloy With Glass Fiber Reinforcement Hybrid Composite

    Directory of Open Access Journals (Sweden)

    Ranga Raj R.,

    2015-05-01

    Full Text Available At present, composite materials are mostly used in aircraft structural components, because of their excellent properties like lightweight, high strength to weight ratio, high stiffness, and corrosion resistance and less expensive. In this experimental work, the mechanical properties of laminate, this is reinforced with stainless steel wire mesh, aluminum sheet metal, perforated aluminum sheet metal and glass fibers to be laminate and investigated. The stainless steel wire mesh and perforated aluminum metal were sequentially stacked to fabricate, hybrid composites. The aluminum metal sheet is also employed with that sequence to get maximum strength and less weight. The tensile, compressive and flexure tests carried out on the hybrid composite. To investigate the mechanical properties and elastic properties of the metal matrix composite laminate of a material we are using experimental test and theoretical calculation. The experimental work consists of Tensile, compressive and flexural test. The expectation of this project results in the tensile and compressive properties of this hybrid composite it is slightly lesser than carbon fibers but it could facilitate a weight reduction compared with CFRP panels. So this hybrid laminates composite material offering significant weight savings and maximum strength over some other GFRP conventional panels.

  15. Experimental Investigation and Analysis of Mercerized and Citric Acid Surface Treated Bamboo Fiber Reinforced Composite

    Science.gov (United States)

    De, Jyotiraman; Baxi, R. N., Dr.

    2017-08-01

    Mercerization or NaOH fiber surface treatment is one of the most popular surface treatment processes to make the natural fibers such as bamboo fibers compatible for use as reinforcing material in composites. But NaOH being a chemical is hazardous and polluting to the nature. This paper explores the possibility of use of naturally derived citric acid for bamboo fiber surface treatment and its comparison with NaOH treated Bamboo Fiber Composites. Untreated, 2.5 wt% NaOH treated and 5 wt% citric acid treated Bamboo Fiber Composites with 5 wt% fiber content were developed by Hand Lay process. Bamboo mats made of bamboo slivers were used as reinforcing material. Mechanical and physical characterization was done to compare the effects of NaOH and citric acid bamboo fiber surface treatment on mechanical and physical properties of Bamboo Fiber Composite. The experiment data reveals that the tensile and flexural strength was found to be highest for citric acid and NaOH treated Bamboo Fiber Composite respectively. Water absorption tendency was found more than the NaOH treated Bamboo Fiber Composites. SEM micrographs used to analyze the morphology of fracture surface of tensile test specimens confirm improvement in fiber-matrix interface bonding due to surface treatment of bamboo fibers.

  16. Thermal Protection of Carbon Fiber-Reinforced Composites by Ceramic Particles

    Directory of Open Access Journals (Sweden)

    Baljinder Kandola

    2016-06-01

    Full Text Available The thermal barrier efficiency of two types of ceramic particle, glass flakes and aluminum titanate, dispersed on the surface of carbon-fiber epoxy composites, has been evaluated using a cone calorimeter at 35 and 50 kW/m2, in addition to temperature gradients through the samples’ thicknesses, measured by inserting thermocouples on the exposed and back surfaces during the cone tests. Two techniques of dispersing ceramic particles on the surface have been employed, one where particles were dispersed on semi-cured laminate and the other where their dispersion in a phenolic resin was applied on the laminate surface, using the same method as used previously for glass fiber composites. The morphology and durability of the coatings to water absorption, peeling, impact and flexural tension were also studied and compared with those previously reported for glass-fiber epoxy composites. With both methods, uniform coatings could be achieved, which were durable to peeling or water absorption with a minimal adverse effect on the mechanical properties of composites. While all these properties were comparable to those previously observed for glass fiber composites, the ceramic particles have seen to be more effective on this less flammable, carbon fiber composite substrate.

  17. Circular Functions Based Comprehensive Analysis of Plastic Creep Deformations in the Fiber Reinforced Composites

    Science.gov (United States)

    Monfared, Vahid

    2016-06-01

    Analytically based model is presented for behavioral analysis of the plastic deformations in the reinforced materials using the circular (trigonometric) functions. The analytical method is proposed to predict creep behavior of the fibrous composites based on basic and constitutive equations under a tensile axial stress. New insight of the work is to predict some important behaviors of the creeping matrix. In the present model, the prediction of the behaviors is simpler than the available methods. Principal creep strain rate behaviors are very noteworthy for designing the fibrous composites in the creeping composites. Analysis of the mentioned parameter behavior in the reinforced materials is necessary to analyze failure, fracture, and fatigue studies in the creep of the short fiber composites. Shuttles, spaceships, turbine blades and discs, and nozzle guide vanes are commonly subjected to the creep effects. Also, predicting the creep behavior is significant to design the optoelectronic and photonic advanced composites with optical fibers. As a result, the uniform behavior with constant gradient is seen in the principal creep strain rate behavior, and also creep rupture may happen at the fiber end. Finally, good agreements are found through comparing the obtained analytical and FEM results.

  18. Mallow Fiber-Reinforced Epoxy Composites in Multilayered Armor for Personal Ballistic Protection

    Science.gov (United States)

    Nascimento, Lucio Fábio Cassiano; Louro, Luis Henrique Leme; Monteiro, Sergio Neves; Lima, Édio Pereira; da Luz, Fernanda Santos

    2017-08-01

    Lighter and less expensive polymer composites reinforced with natural fibers have been investigated as possible components of a multilayered armor system (MAS) for personal protection against high-velocity ammunition. Their ballistic performance was consistently found comparable with that of conventional Kevlar® synthetic aramid fiber. Among the numerous existing natural fibers with the potential for reinforcing polymer composites to replace Kevlar® in MAS, mallow fiber has not been fully investigated. Thus, the objective of this work is to evaluate the ballistic performance of epoxy composites reinforced with 30 vol.% of aligned mallow fibers as a second MAS layer backing a front ceramic plate. The results using high-velocity 7.62 ammunition show a similar indentation to a Kevlar® layer with the same thickness. An impedance matching calculation supports the similar ballistic performance of mallow fiber composite and Kevlar®. Reduced MAS costs associated with the mallow fiber composite are practical advantages over Kevlar®.

  19. Circular Functions Based Comprehensive Analysis of Plastic Creep Deformations in the Fiber Reinforced Composites

    Science.gov (United States)

    Monfared, Vahid

    2016-12-01

    Analytically based model is presented for behavioral analysis of the plastic deformations in the reinforced materials using the circular (trigonometric) functions. The analytical method is proposed to predict creep behavior of the fibrous composites based on basic and constitutive equations under a tensile axial stress. New insight of the work is to predict some important behaviors of the creeping matrix. In the present model, the prediction of the behaviors is simpler than the available methods. Principal creep strain rate behaviors are very noteworthy for designing the fibrous composites in the creeping composites. Analysis of the mentioned parameter behavior in the reinforced materials is necessary to analyze failure, fracture, and fatigue studies in the creep of the short fiber composites. Shuttles, spaceships, turbine blades and discs, and nozzle guide vanes are commonly subjected to the creep effects. Also, predicting the creep behavior is significant to design the optoelectronic and photonic advanced composites with optical fibers. As a result, the uniform behavior with constant gradient is seen in the principal creep strain rate behavior, and also creep rupture may happen at the fiber end. Finally, good agreements are found through comparing the obtained analytical and FEM results.

  20. Mallow Fiber-Reinforced Epoxy Composites in Multilayered Armor for Personal Ballistic Protection

    Science.gov (United States)

    Nascimento, Lucio Fábio Cassiano; Louro, Luis Henrique Leme; Monteiro, Sergio Neves; Lima, Édio Pereira; da Luz, Fernanda Santos

    2017-10-01

    Lighter and less expensive polymer composites reinforced with natural fibers have been investigated as possible components of a multilayered armor system (MAS) for personal protection against high-velocity ammunition. Their ballistic performance was consistently found comparable with that of conventional Kevlar® synthetic aramid fiber. Among the numerous existing natural fibers with the potential for reinforcing polymer composites to replace Kevlar® in MAS, mallow fiber has not been fully investigated. Thus, the objective of this work is to evaluate the ballistic performance of epoxy composites reinforced with 30 vol.% of aligned mallow fibers as a second MAS layer backing a front ceramic plate. The results using high-velocity 7.62 ammunition show a similar indentation to a Kevlar® layer with the same thickness. An impedance matching calculation supports the similar ballistic performance of mallow fiber composite and Kevlar®. Reduced MAS costs associated with the mallow fiber composite are practical advantages over Kevlar®.

  1. A study of void effects on the interlaminar shear strength of unidirectional graphite fiber reinforced composites

    Science.gov (United States)

    Bowles, Kenneth J.; Frimpong, Stephen

    1990-01-01

    A study was conducted to evaluate the effect of voids on the interlaminar shear strength (ILSS) of a polyimide matrix composite system. The graphite/PRM-15 composite was chosen for study because of the extensive amount of experience that has been amassed in the processing of this material. Composite densities and fiber contents of more than thirty different laminates were measured along with ILSS. Void contents were calculated and the void geometry and distribution were noted using microscopic techniques such as those used in metallography. It was found that there was a good empirical correlation between ILSS and composite density. The most acceptable relationship between the ILSS and density was found to be a power equation which closely resembles theoretically derived expressions. An increase in scatter in the strength data was observed as the void content increased. In laminates with low void content, the void appears to be more segregated in one area of the laminate. It was found that void free composites could be processed in matched metal die molds at pressures greater than 1.4 and less than 6.9 MPa.

  2. A Study of Failure Strength for Fiber-Reinforced Composite Laminates with Consideration of Interface

    Directory of Open Access Journals (Sweden)

    Junjie Ye

    2015-01-01

    Full Text Available Composite laminates can exhibit the nonlinear properties due to the fiber/matrix interface debonding and matrix plastic deformation. In this paper, by incorporating the interface stress-displacement relations between fibers and matrix, as well as the viscoplastic constitutive model for describing plastic behaviors of matrix materials, a micromechanical model is used to investigate the failure strength of the composites with imperfect interface bonding. Meanwhile, the classic laminate theory, which provides the relation between micro- and macroscale responses for composite laminates, is employed. Theory results show good consistency with the experimental data under unidirectional tensile conditions at both 23°C and 650°C. On this basis, the interface debonding influences on the failure strength of the [0/90]s and [0/±45/90]s composite laminates are studied. The numerical results show that all of the unidirectional (UD laminates with imperfect interface bonding provide a sharp decrease in failure strength in the σxx-σyy plane at 23°C. However, the decreasing is restricted in some specific region. In addition, for [0/90]s and [0/±45/90]s composite laminates, the debonding interface influences on the failure envelope can be ignored when the working temperature is increased to 650°C.

  3. Drop Weight Impact Studies of Woven Fibers Reinforced Modified Polyester Composites

    Directory of Open Access Journals (Sweden)

    Muhammed Tijani ISA

    2014-02-01

    Full Text Available Low velocity impact tests were conducted on modified unsaturated polyester reinforced with four different woven fabrics using hand-layup method to investigate the effect of fiber type and fiber combinations. The time-load curves were analysed and scanning electron microscopy was used to observe the surface of the impacted composite laminates. The results indicated that all the composites had ductility index (DI of above two for the test conducted at impact energy of 27J with the monolithic composite of Kevlar having the highest DI. The damage modes observed were mainly matrix cracks and fiber breakages. Hybridization of the fibers in the matrix was observed to minimize these damages.

  4. Effects of high energy radiation on the mechanical properties of epoxy/graphite fiber reinforced composites

    Science.gov (United States)

    Fornes, R. E.; Gilbert, R. D.; Memory, J. D.

    1987-01-01

    Publications and theses generated on composite research are listed. Surface energy changes of an epoxy based on tetraglycidyl diaminodiphenyl methane (TGDDM)/diaminodiphenyl sulfone (DDS), T-300 graphite fiber and T-300/5208 (graphite fiber/epoxy) composites were investigated after irradiation with 0.5 MeV electrons. Electron spin resonance (ESR) investigations of line shapes and the radical decay behavior were made of an epoxy based on tetraglycidyl diaminodiphenyl methane (TGDDM)/diaminodiphenyl sulfone (DDS), T-300 graphite fiber, and T-300/5208 (graphite fiber/epoxy) composites after irradiation with Co(60) gamma-radiation or 0.5 MeV electrons. The results of the experiments are discussed.

  5. Separation of the Martensite in TiNi Fiber Reinforced Aluminum Matrix Composite

    Institute of Scientific and Technical Information of China (English)

    Yanjun ZHENG; Lishan CUI; Yan LI; Dazhi YANG

    2004-01-01

    The reverse martensitic transformation of TiNi shape memory alloy fibers embedded in a pure aluminum matrix was studied in this paper. Results showed that the phase composition of the TiNi alloy fibers prior to prestraining at the room temperature had a significant influence on the differential scanning calorimetry (DSC) results of the composites. By a comparison to the high temperature X-ray diffraction (XRD) results, it was confirmed that the martensite was divided into two groups: the selfaccommodating martensite (SAM) and the preferentially oriented martensite (POM). The evolving process of the separation of martensite was discussed.

  6. Final Report: Interphase Analysis and Control in Fiber Reinforced Thermoplastic Composites

    Energy Technology Data Exchange (ETDEWEB)

    Jon J. Kellar; William M. Cross; Lidvin Kjerengtroen

    2009-03-14

    This research program builds upon a multi-disciplinary effort in interphase analysis and control in thermoplastic matrix polymer matrix composites (PMC). The research investigates model systems deemed of interest by members of the Automotive Composites Consortium (ACC) as well as samples at the forefront of PMC process development (DRIFT and P4 technologies). Finally, the research investigates, based upon the fundamental understanding of the interphases created during the fabrication of thermoplastic PMCs, the role the interphase play in key bulk properties of interest to the automotive industry.

  7. Automotive view on forming of continuous fiber reinforced composites and its simulation

    Science.gov (United States)

    Eck, Benedikt; Chambon, Guillaume

    2016-10-01

    This paper presents three projects of Faurecia in the domain of composite part forming and an evaluation of current forming simulation approaches regarding an application in the automotive industry. Via the latter the most performant group of currently available simulation approaches is identified. Their main drawback is however a high computational effort and further research should be done in order to accelerate them. Hereafter recommendations for an ideal forming simulation approach are identified by presenting three projects of Faurecia in the domain of composite part forming.

  8. Numerical investigation of friction joint between Basalt Fiber Reinforced Composites and aluminum

    DEFF Research Database (Denmark)

    Costache, Andrei; Berggreen, Christian; Sivebæk, Ion Marius

    2016-01-01

    Flexible risers are used in the offshore oil industry for exporting hydrocarbons from subsea equipment to floatingproduction and storage vessels. The latest research in unbonded flexible pipes aims to reduce weight by replacing metal components with composite materials. This would result in light...

  9. Damage Precursor Investigation of Fiber-Reinforced Composite Materials Under Fatigue Loads

    Science.gov (United States)

    2013-09-01

    measures of damage that act as damage precursors also exist, such as electric resistance (Wang et al., 1998; Irving and 4 Thiagarajan, 1998; Weber... Irving , P. E.; Thiagarajan, C. Fatigue Damage Characterization in Carbon Fibre Composite Materials Using an Electrical Potential Technique. Smart...30 NO. OF COPIES ORGANIZATION 1 DEFENSE TECHNICAL (PDF) INFORMATION CTR DTIC OCA 2 DIRECTOR (PDFS) US ARMY RESEARCH LAB

  10. Accounting for Fiber Bending Effects in Homogenization of Long Fiber Reinforced Composites

    DEFF Research Database (Denmark)

    Poulios, Konstantinos; Niordson, Christian Frithiof

    2015-01-01

    constitutive laws for the fiber and the matrix materials, respectively expressed in the frameworks of hyper-elasticity and hyper-elasto-plasticity. The presented numerical results include comparisons between the homogenized model and an explicit discretization of the composite microstructure. Both models...

  11. Detection of Environmental Deterioration in Fiber Reinforced Composites by FT-Raman Spectroscopy. Phase 1

    Science.gov (United States)

    1994-05-01

    These methods have been developed to measure material flaws in composites, such as cracks, voids , delamination andI defomation.7 These methods are...detector having a 0.5 mm radius and an OT of 0.52 mm2 steradians allowing 100% light collection. Yet the detector is underfilled with a coupling

  12. Fabrication of Glass Fiber Reinforced Composites Based on Bio-Oil Phenol Formaldehyde Resin

    Directory of Open Access Journals (Sweden)

    Yong Cui

    2016-11-01

    Full Text Available In this study, bio-oil from fast pyrolysis of renewable biomass was added by the mass of phenol to synthesize bio-oil phenol formaldehyde (BPF resins, which were used to fabricate glass fiber (GF reinforced BPF resin (GF/BPF composites. The properties of the BPF resin and the GF/BPF composites prepared were tested. The functional groups and thermal property of BPF resin were thoroughly investigated by Fourier transform infrared (FTIR spectra and dynamic thermomechanical analysis (DMA. Results indicated that the addition of 20% bio-oil exhibited favorable adaptability for enhancing the stiffness and heat resistance of phenol formaldehyde (PF resin. Besides, high-performance GF/BPF composites could be successfully prepared with the BPF resin based on hand lay-up process. The interface characteristics of GF/BPF composites were determined by the analysis of dynamic wettability (DW and scanning electron microscopy (SEM. It exhibited that GF could be well wetted and embedded in the BPF resin with the bio-oil addition of 20%.

  13. Influence of chemical treatment on the tensile properties of kenaf fiber reinforced thermoplastic polyurethane composite

    Directory of Open Access Journals (Sweden)

    Y. A. El-Shekeil

    2012-12-01

    Full Text Available In this study, the effect of polymeric Methylene Diphenyl Diisocyanate (pMDI chemical treatment on kenaf (Hibiscus cannabinus reinforced thermoplastic polyurethane (TPU/KF was examined using two different procedures. The first consisted of treating the fibers with 4% pMDI, and the second involved 2% NaOH + 4% pMDI. The composites were characterized according to their tensile properties, Fourier Transform Infrared Spectroscopy (FTIR and Scanning Electron Microscopy (SEM. The treatment of the composite with 4% pMDI did not significantly affect its tensile properties, but the treatment with 2% NaOH + 4% pMDI significantly increased the tensile properties of the composite (i.e., 30 and 42% increases in the tensile strength and modulus, respectively. FTIR also showed that treatment with 2% NaOH + 4% pMDI led to the strongest H-bonding. Additionally, the surface morphology of specimens after tensile fracture confirmed that the composite treated with 2% NaOH + 4% pMDI had the best adhesion and wettability.

  14. Damage Tolerance Enhancement of Carbon Fiber Reinforced Polymer Composites by Nanoreinforcement of Matrix

    Science.gov (United States)

    Fenner, Joel Stewart

    Nanocomposites are a relatively new class of materials which incorporate exotic, engineered nanoparticles to achieve superior material properties. Because of their extremely small size and well-ordered structure, many nanoparticles possess properties that exceed those offered by a wide range of other known materials, making them attractive candidates for novel materials engineering development. Their small size is also an impediment to their practical use, as they typically cannot be employed by themselves to realize those properties in large structures. Furthermore, nanoparticles typically possess strong self-affinity, rendering them difficult to disperse uniformly into a composite. However, contemporary research has shown that, if well-dispersed, nanoparticles have great capacity to improve the mechanical properties of composites, especially damage tolerance, in the form of fracture toughness, fatigue life, and impact damage mitigation. This research focuses on the development, manufacturing, and testing of hybrid micro/nanocomposites comprised of woven carbon fibers with a carbon nanotube reinforced epoxy matrix. Material processing consisted of dispersant-and-sonication based methods to disperse nanotubes into the matrix, and a vacuum-assisted wet lay-up process to prepare the hybrid composite laminates. Various damage tolerance properties of the hybrid composite were examined, including static strength, fracture toughness, fatigue life, fatigue crack growth rate, and impact damage behavior, and compared with similarly-processed reference material produced without nanoreinforcement. Significant improvements were obtained in interlaminar shear strength (15%), Mode-I fracture toughness (180%), shear fatigue life (order of magnitude), Mode-I fatigue crack growth rate (factor of 2), and effective impact damage toughness (40%). Observations by optical microscopy, scanning electron microscopy, and ultrasonic imaging showed significant differences in failure behavior

  15. Three-point bending test comparison of fiber-reinforced composite archwires to nickel-titanium archwires.

    Science.gov (United States)

    Ballard, Richard W; Sarkar, Nikhil K; Irby, Merrell C; Armbruster, Paul C; Berzins, David W

    2012-01-01

    Various alternatives to metal orthodontic archwires have produced varied successes over the years. This study sought to evaluate the bending properties of fiber-reinforced polymeric composite (FRC) archwires compared with similarly sized nickel-titanium (Ni-Ti) archwires. Two different 0.018-inch translucent FRC orthodontic wires (Translucent Archwire I and Translucent Archwire II) were tested against 0.014-, 0.016-, and 0.018-inch nonsuperelastic nickel titanium orthodontic wires. The wires in each group (n = 10) were evaluated with three-point bending using a universal testing machine. Wire segments were deflected at midspan to 3.1 mm at a rate of 2 mm/min. Loading and unloading slope and modulus were calculated, as were force values during activation and deactivation and elastic recovery. It was found that the 0.018-inch Ni-Ti archwire demonstrated the highest force values at different deflection distances followed by Translucent Archwire II, 0.016-inch Ni-Ti, Translucent Archwire I, and finally 0.014-inch Ni-Ti. 0.016-inch Ni-Ti exhibited the highest modulus value, followed by 0.018-inch Ni-Ti, 0.014-inch Ni-Ti, Translucent Archwire II, and finally Translucent Archwire I. During deactivation, the elastic recovery of 0.014-inch Ni-Ti and 0.016-inch Ni-Ti was significantly greater than Translucent Archwire II. The bending properties of BioMer's FRC archwires were found to be comparable to Ni-Ti, as advertised by the manufacturer.

  16. Manufacture of magnetically active fiber-reinforced composites for use in power generation

    Science.gov (United States)

    Etches, Julie; Bond, Ian; Mellor, Phil

    2004-07-01

    A major issue yet to be resolved for embedding sensors, actuators and microelectromechanical systems (MEMS) in 'smart' structures is that of providing power. Work is ongoing in the field with examples of micro battery technology, use of solar power and micro fuel cells. The work presented here considers a technology to enable the development of integrated power generation and actuation. Magnetic fibre reinforced composite material has been developed which utilises hollow glass fibres filled with active magnetic material. The resulting material maintains structural integrity as well as providing a possible means of electrical power generation from a dynamically loaded structure. The hollow glass fibres were manufactured in-house using a bespoke fibre drawing facility. Hard magnetic powder materials were introduced into the hollow fibre cores to provide an active electromagnetic function. This paper will discuss the manufacture, characterization and optimisation of active magnetic fibre reinforced composite materials.

  17. Fracture behavior of pontics of fiber-reinforced composite fixed dental prostheses.

    Science.gov (United States)

    Perea, Leila; Matinlinna, Jukka P; Tolvanen, Mimmi; Vallittu, Pekka K

    2015-01-01

    To evaluate the load-bearing capacities and failure mechanisms of FRC FDPs using shell-shaped acrylic denture teeth as pontics with different composite resins as filling materials. Eighty-four inlay-retained FDPs with FRC frameworks were made using shell-shaped posterior artificial teeth as pontics. Different composite resins were used as filling materials to complete the shape of the pontics. Four groups (n=21/group) were formed based on the filling material. Each group was subdivided into three subgroups and tested at 90º and 30°. Each FDP was statically loaded from the pontic until the final fracture. ANOVA revealed statistically significant differences in the load-bearing capacities according to filling material, angle and storage (pfilling material influenced the load-bearing capacities of FRC FDPs with shell-shaped denture teeth used as pontics.

  18. Monitoring the Damage State of Fiber Reinforced Composites Using an FBG Network for Failure Prediction

    Directory of Open Access Journals (Sweden)

    Esat Selim Kocaman

    2017-01-01

    Full Text Available A structural health monitoring (SHM study of biaxial glass fibre-reinforced epoxy matrix composites under a constant, high strain uniaxial fatigue loading is performed using fibre Bragg grating (FBG optical sensors embedded in composites at various locations to monitor the evolution of local strains, thereby understanding the damage mechanisms. Concurrently, the temperature changes of the samples during the fatigue test have also been monitored at the same locations. Close to fracture, significant variations in local temperatures and strains are observed, and it is shown that the variations in temperature and strain can be used to predict imminent fracture. It is noted that the latter information cannot be obtained using external strain gages, which underlines the importance of the tracking of local strains internally.

  19. Compressive strength of fiber reinforced composite materials. [composed of boron and epoxy

    Science.gov (United States)

    Davis, J. G., Jr.

    1974-01-01

    Results of an experimental and analytical investigation of the compressive strength of unidirectional boron-epoxy composite material are presented. Observation of fiber coordinates in a boron-epoxy composite indicates that the fibers contain initial curvature. Combined axial compression and torsion tests were conducted on boron-epoxy tubes, and it was shown that the shear modulus is a function of axial compressive stress. An analytical model which includes initial curvature in the fibers and permits an estimate of the effect of curvature on compressive strength is proposed. Two modes of failure which may result from the application of axial compressive stress are analyzed, delamination and shear instability. Based on tests and analysis, failure of boron-epoxy under axial compressive load is due to shear instability.

  20. Experimental Test of Stainless Steel Wire Mesh and Aluminium Alloy With Glass Fiber Reinforcement Hybrid Composite

    OpenAIRE

    2015-01-01

    At present, composite materials are mostly used in aircraft structural components, because of their excellent properties like lightweight, high strength to weight ratio, high stiffness, and corrosion resistance and less expensive. In this experimental work, the mechanical properties of laminate, this is reinforced with stainless steel wire mesh, aluminum sheet metal, perforated aluminum sheet metal and glass fibers to be laminate and investigated. The stainless steel wire mesh and...

  1. Lyocell Fiber-Reinforced Cellulose Ester Composites-Manufacturing Considerations and Properties.

    OpenAIRE

    1999-01-01

    Biodegradable thermoplastic composites were prepared using high modulus lyocell fibers and cellulose acetate butyrate (CAB). Two reinforcement fiber types: fabric and continuous fiber tow were used. Fabric had advantages of uniform alignment and easier processing, but lacked the use as a unidirectional reinforcement and a continuous method of matrix application. Three different matrix application methods were screened for both fiber types. Matrix application by suspension of particles in wate...

  2. Electrical conductivity improvement of aeronautical carbon fiber reinforced polyepoxy composites by insertion of carbon nanotubes

    OpenAIRE

    Lonjon, Antoine; Demont, Philippe; Dantras, Eric; Lacabanne, Colette

    2012-01-01

    International audience; An increase and homogenization of electrical conductivity is essential in epoxy carbon fiber laminar aeronautical composites. Dynamic conductivity measurements have shown a very poor transversal conductivity. Double wall carbon nanotubes have been introduced into the epoxy matrix to increase the electrical conductivity. The conductivity and the degree of dispersion of carbon nanotubes in epoxy matrix were evaluated. The epoxy matrix was filled with 0.4 wt.% of CNTs to ...

  3. The group velocity variation of Lamb wave in fiber reinforced composite plate.

    Science.gov (United States)

    Rhee, Sang-Ho; Lee, Jeong-Ki; Lee, Jung-Ju

    2007-12-01

    Experimentally measured Lamb wave group velocities in composite materials with anisotropic characteristics are not the same as the theoretical group velocities which is calculated with the Lamb wave dispersion equation. This discrepancy arises from the fact that the angle between the group velocity direction and the phase velocity direction in anisotropic materials exists. Wave propagation in a composite material with anisotropic characteristics should be considered with respect to magnitude correction in addition to direction correction. In this study, S0 mode phase velocity dispersion curves are depicted with the variation of degree with respect to the fiber direction using a Lamb wave dispersion relation in the unidirectional, bidirectional, and quasi-isotropic composite plates. Slowness surface is sketched by the reciprocal value of the phase velocity curves. The magnitude and direction of the group velocity could be calculated from the slowness surface. The recalculated group velocities with consideration of the magnitude and direction from the slowness surface are compared with experimentally measured group velocities. The proposed method shows good agreements with theoretical and experimental results.

  4. Numerical approach of the injection molding process of fiber-reinforced composite with considering fiber orientation

    Energy Technology Data Exchange (ETDEWEB)

    Nguyen Thi, T. B., E-mail: thanhbinh.skku@gmail.com, E-mail: yokoyama@kit.ac.jp; Yokoyama, A., E-mail: thanhbinh.skku@gmail.com, E-mail: yokoyama@kit.ac.jp [Department of Advanced Fibro-Science, Kyoto Institute of Technology (Japan); Ota, K., E-mail: kei-ota@toyobo.jp, E-mail: katsuhiro-kodama@toyobo.jp, E-mail: katsuhisa-yamashita@toyobo.jp, E-mail: yumiko-isogai@toyobo.jp, E-mail: kenji-furuichi@toyobo.jp, E-mail: chisato-nonomura@toyobo.jp; Kodama, K., E-mail: kei-ota@toyobo.jp, E-mail: katsuhiro-kodama@toyobo.jp, E-mail: katsuhisa-yamashita@toyobo.jp, E-mail: yumiko-isogai@toyobo.jp, E-mail: kenji-furuichi@toyobo.jp, E-mail: chisato-nonomura@toyobo.jp; Yamashita, K., E-mail: kei-ota@toyobo.jp, E-mail: katsuhiro-kodama@toyobo.jp, E-mail: katsuhisa-yamashita@toyobo.jp, E-mail: yumiko-isogai@toyobo.jp, E-mail: kenji-furuichi@toyobo.jp, E-mail: chisato-nonomura@toyobo.jp; Isogai, Y., E-mail: kei-ota@toyobo.jp, E-mail: katsuhiro-kodama@toyobo.jp, E-mail: katsuhisa-yamashita@toyobo.jp, E-mail: yumiko-isogai@toyobo.jp, E-mail: kenji-furuichi@toyobo.jp, E-mail: chisato-nonomura@toyobo.jp; Furuichi, K., E-mail: kei-ota@toyobo.jp, E-mail: katsuhiro-kodama@toyobo.jp, E-mail: katsuhisa-yamashita@toyobo.jp, E-mail: yumiko-isogai@toyobo.jp, E-mail: kenji-furuichi@toyobo.jp, E-mail: chisato-nonomura@toyobo.jp; Nonomura, C., E-mail: kei-ota@toyobo.jp, E-mail: katsuhiro-kodama@toyobo.jp, E-mail: katsuhisa-yamashita@toyobo.jp, E-mail: yumiko-isogai@toyobo.jp, E-mail: kenji-furuichi@toyobo.jp, E-mail: chisato-nonomura@toyobo.jp [Toyobo Co., LTD. Research Center (Japan)

    2014-05-15

    One of the most important challenges in the injection molding process of the short-glass fiber/thermoplastic composite parts is being able to predict the fiber orientation, since it controls the mechanical and the physical properties of the final parts. Folgar and Tucker included into the Jeffery equation a diffusive type of term, which introduces a phenomenological coefficient for modeling the randomizing effect of the mechanical interactions between the fibers, to predict the fiber orientation in concentrated suspensions. Their experiments indicated that this coefficient depends on the fiber volume fraction and aspect ratio. However, a definition of the fiber interaction coefficient, which is very necessary in the fiber orientation simulations, hasn't still been proven yet. Consequently, this study proposed a developed fiber interaction model that has been introduced a fiber dynamics simulation in order to obtain a global fiber interaction coefficient. This supposed that the coefficient is a sum function of the fiber concentration, aspect ratio, and angular velocity. The proposed model was incorporated into a computer aided engineering simulation package C-Mold. Short-glass fiber/polyamide-6 composites were produced in the injection molding with the fiber weight concentration of 30 wt.%, 50 wt.%, and 70 wt.%. The physical properties of these composites were examined, and their fiber orientation distributions were measured by micro-computed-tomography equipment μ-CT. The simulation results showed a good agreement with experiment results.

  5. Supersonic Retropulsion Surface Preparation of Carbon Fiber Reinforced Epoxy Composites for Adhesive Bonding

    Science.gov (United States)

    Palmieri, Frank L.; Belcher, Marcus A.; Wohl, Christopher J.; Blohowiak, Kay Y.; Connell, John W.

    2013-01-01

    Surface preparation is widely recognized as a key step to producing robust and predictable bonds in a precise and reproducible manner. Standard surface preparation techniques, including grit blasting, manual abrasion, and peel ply, can lack precision and reproducibility, which can lead to variation in surface properties and subsequent bonding performance. The use of a laser to ablate composite surface resin can provide an efficient, precise, and reproducible means of preparing composite surfaces for adhesive bonding. Advantages include elimination of physical waste (i.e., grit media and sacrificial peel ply layers that ultimately require disposal), reduction in process variability due to increased precision (e.g. increased reproducibility), and automation of surface preparation, all of which improve reliability and process control. This paper describes a Nd:YAG laser surface preparation technique for composite substrates and the mechanical performance and failure modes of bonded laminates thus prepared. Additionally, bonded specimens were aged in a hot, wet environment for approximately one year and subsequently mechanically tested. The results of a one year hygrothermal aging study will be presented.

  6. Scattering of Lamb waves by cracks in a composite graphite fiber-reinforced epoxy plate

    Science.gov (United States)

    Bratton, Robert; Datta, Subhendu K.; Shah, Arvind

    1990-01-01

    Recent investigations of space construction techniques have explored the used of composite materials in the construction of space stations and platforms. These composites offer superior strength to weight ratio and are thermally stable. For example, a composite material being considered is laminates of graphite fibers in an epoxy matrix. The overall effective elastic constants of such a medium can be calculated from fiber and matrix properties by using an effective modulus theory as shown in Datta, el. al. The investigation of propagation and scattering of elastic waves in composite materials is necessary in order to develop an ability to characterize cracks and predict the reliability of composite structures. The objective of this investigation is the characterization of a surface breaking crack by ultrasonic techniques. In particular, the use of Lamb waves for this purpose is studied here. The Lamb waves travel through the plate, encountering a crack, and scatter. Of interest is the modeling of the scattered wave in terms of the Lamb wave modes. The direct problem of propagation and scattering of Lamb waves by a surface breaking crack has been analyzed. This would permit an experimentalist to characterize the crack by comparing the measured response to the analytical model. The plate is assumed to be infinite in the x and y directions with a constant thickness in the z direction. The top and bottom surfaces are traction free. Solving the governing wave equations and using the stress-free boundary conditions results in the dispersion equation. This equation yields the guided modes in the homogeneous plate. The theoretical model is a hybrid method that combines analytical and finite elements techniques to describe the scattered displacements. A finite region containing the defects is discretized by finite elements. Outside the local region, the far field solution is expressed as a Fourier summation of the guided modes obtained from the dispersion equation

  7. Forming of carbon fiber reinforced thermoplastic composite tubes - Experimental and numerical approaches

    Science.gov (United States)

    Maron, Bernhard; Garthaus, Christian; Lenz, Florian; Hornig, Andreas; Hübner, Michael; Gude, Maik

    2016-10-01

    Continuous-reinforced thermoplastic composites are of growing importance for series production of lightweight components in manifold industrial areas. Novel manufacturing technologies allow the production of hollow semi-finished products that are post formed to enhance functionality. To maximize efficiency in the development process of such components it is necessary to map the forming processes numerically using Finite Elements(FE)-methods. The aim is to perform feasibility studies at an early stage, reduce development time by virtual process optimization and to generate a detailed understanding of the post formed fiber architecture for further structural-mechanical analysis.

  8. Martensitic Transformation of TiNi Shape Memory Alloy Fiber Reinforced Ni Matrix Composites

    Institute of Scientific and Technical Information of China (English)

    Lishan CUI; Yan LI; Yan jun ZHENG; Huibin XU

    2003-01-01

    In this paper, a TiNi shape memory alloy fiber Ni matrix composite was fabricated by an electroplating method using TiNialloy as the cathode and Ni as the anode. The constrained martensitic transformation behaviors of the TiNi alloy were studiedby differential scanning calorimeter (DSC), and the results showed that two endothermic peaks appear on the DSC heatingcurves and the reverse transformation temperatures increase with increasing prestrain levels. Moreover, comparing to the freetransformation, the temperature window of the constrained reverse transformation is widely expanded due to the influence ofrecovery stress.

  9. Studies of Matrix/Fiber Reinforced Composite Materials for the High Speed Research (HSR) Program

    Science.gov (United States)

    Orwoll, Robert A.

    1998-01-01

    The research on the curing mechanism of the phenylethynyl terminated imide matrix resins was the primary focus of this research. The ability to process high performance polymers into useful adhesives and high quality composites has been significantly advanced by synthetic techniques in which oligomers terminated with reactive groups cure or crosslink at elevated temperature after the article has been fabricated. The research used a variety of analytical techniques. Many stable products were isolated, and attempts at identification were made. This research was intended to provide fundamental insight into the molecular structure of these new engineering materials.

  10. Development of Carbon Fiber Reinforced Stellite Alloy Based Composites for Tribocorrosion Applications

    Science.gov (United States)

    Khoddamzadeh, Alireza

    This thesis reports the design and development of two classes of new composite materials, which are low-carbon Stellite alloy matrices, reinforced with either chopped plain carbon fiber or chopped nickel-coated carbon fiber. The focus of this research is on obviating the problems related to the presence of carbides in Stellite alloys by substituting carbides as the main strengthening agent in Stellite alloys with the aforementioned carbon fibers. Stellite 25 was selected as the matrix because of its very low carbon content (0.1 wt%) and thereby relatively carbide free microstructure. The nickel coating was intended to eliminate any chance of carbide formation due to the possible reaction between carbon fibers and the matrix alloying additions. The composite specimens were fabricated using the designed hot isostatic pressing and sintering cycles. The fabricated specimens were microstructurally analyzed in order to identify the main phases present in the specimens and also to determine the possible carbide formation from the carbon fibers. The material characterization of the specimens was achieved through density, hardness, microhardness, corrosion, wear, friction, and thermal conductivity tests. These novel materials exhibit superior properties compared to existing Stellite alloys and are expected to spawn a new generation of materials used for high temperature, severe corrosion, and wear resistant applications in various industries.

  11. Process for the manufacture of seamless metal-clad fiber-reinforced organic matrix composite structures

    Science.gov (United States)

    Bluck, Raymond M. (Inventor); Bush, Harold G. (Inventor); Johnson, Robert R. (Inventor)

    1991-01-01

    A process for producing seamless metal-clad composite structures includes providing a hollow, metallic inner member and an outer sleeve to surround the inner member and define an inner space therebetween. A plurality of continuous reinforcing fibers is attached to the distal end of the outside diameter of the inner member, and the inner member is then introduced, distal end first, into one end of the outer sleeve. The inner member is then moved, distal end first, into the outer sleeve until the inner member is completely enveloped by the outer sleeve. A liquid matrix material is then injected into the space containing the reinforcing fibers between the inner member and the outer sleeve. Next a pressurized heat transfer medium is passed through the inner member to cure the liquid matrix material. Finally, the wall thickness of both the inner member and the outer sleeve are reduced to desired dimensions by chemical etching, which adjusts the thermal expansion coefficient of the metal-clad composite structure to a desired value.

  12. Mullite fiber reinforced reaction bonded Si{sub 3}N{sub 4} composites

    Energy Technology Data Exchange (ETDEWEB)

    Saleh, T.; Lightfoot, A.; Haggerty, J. [Massachusetts Institute of Technology, Cambridge, MA (United States); Sayir, A. [NASA Lewis Research Center, Cleveland, OH (United States)

    1996-12-31

    Fracture toughnesses of brittle ceramic materials have been improved by introducing reinforcements and carefully tailored interface layers. Silicon carbide and Si{sub 3}N{sub 4} have been emphasized as matrices of structural composites intended for high temperature service because they combine excellent mechanical, chemical, thermal and physical properties. Both matrices have been successfully toughened with SiC fibers, whiskers and particles for ceramic matrix composite (CMC) parts made by sintering, hot pressing or reaction forming processes. These SiC reinforced CMCs have exhibited significantly improved toughnesses at low and intermediate temperature levels, as well as retention of properties at high temperatures for selected exposures; however, they are vulnerable to attack from elevated temperature dry and wet oxidizing atmospheres after the matrix has cracked. Property degradation results from oxidation of interface layers and/or reinforcements. The problem is particularly acute for small diameter ({approximately}20 {mu}m) polymer derived SiC fibers used for weavable toes. This research explored opportunities for reinforcing Si{sub 3}N{sub 4} matrices with fibers having improved environmental stability; the finding should also be applicable to SiC matrix CMCs.

  13. Sustainable Energy Solutions Task 4.2: UV Degradation Prevention on Fiber-Reinforced Composite Blades

    Energy Technology Data Exchange (ETDEWEB)

    Janet M. Twomey, PhD

    2010-04-30

    EXECUTIVE SUMARRY Use of wind energy has expanded very quickly because of the energy prices, environmental concerns and improved efficiency of wind generators. Rather than using metal and alloy based wind turbine blades, larger size fiber (glass and carbon) reinforced composite blades have been recently utilized to increase the efficiency of the wind energy in both high and low wind potential areas. In the current composite manufacturing, pre-preg and vacuum-assisted/heat sensitive resin transfer molding and resin infusion methods are employed. However, these lighter, stiffer and stronger composite blades experience ultraviolet (UV) light degradation where polymers (epoxies and hardeners) used for the blades manufacturing absorb solar UV lights, and cause photolytic, thermo-oxidative and photo-oxidative reactions resulting in breaking of carbon-hydrogen bonds, polymer degradation and internal and external stresses. One of the main reasons is the weak protective coatings/paints on the composite blades. This process accelerates the aging and fatigue cracks, and reduces the overall mechanical properties of the blades. Thus, the lack of technology on coatings for blade manufacturing is forcing many government agencies and private companies (local and national windmill companies) to find a better solution for the composite wind blades. Kansas has a great wind potential for the future energy demand, so efficient wind generators can be an option for continuous energy production. The research goal of the present project was to develop nanocomposite coatings using various inclusions against UV degradation and corrosion, and advance the fundamental understanding of degradation (i.e., physical, chemical and physiochemical property changes) on those coatings. In pursuit of the research goal, the research objective of the present program was to investigate the effects of UV light and duration on various nanocomposites made mainly of carbon nanotubes and graphene nanoflakes

  14. The chemistry of dimethacrylate-styrene networks, and, Development of flame retardant, halogen-free fiber reinforced vinyl ester composites

    Science.gov (United States)

    Rosario, Astrid Christa

    One of the major classes of polymer matrix resins under consideration for structural composite applications in the infrastructure and construction industries is vinyl ester resin. Vinyl ester resin is comprised of low molecular weight poly(hydroxyether) oligomers with methacrylate endgroups diluted with styrene monomer. The methacrylate endgroups cure with styrene via free radical copolymerization to yield thermoset networks. The copolymerization behavior of these networks was monitored by Fourier Transform Infrared Spectroscopy (FTIR) at various cure conditions. Reactions of the carbon-carbon double bonds of the methacrylate (943 cm-1) and styrene (910 cm-1 ) were followed independently. Oligomers possessing number average molecular weights of 700 g/mole were studied with systematically increasing levels of styrene. The Mortimer-Tidwell reactivity ratios indicated that at low conversion more styrene was incorporated into the network at lower cure temperatures. The experimental vinyl ester-styrene network compositions deviated significantly from those predicted by the Meyer-Lowry integrated copolymer equation at higher conversion, implying that the reactivity ratios for these networks may change with conversion. The kinetic data were used to provide additional insight into the physical and mechanical properties of these materials. In addition to establishing the copolymerization kinetics of these materials, the development of halogen free fiber reinforced vinyl ester composites exhibiting good flame properties was of interest. Flame retardant vinyl ester resins are used by many industries for applications requiring good thermal resistance. The current flame-retardant technology is dependent on brominated vinyl esters, which generate high levels of smoke and carbon monoxide. A series of halogen free binder systems has been developed and dispersed in the vinyl ester to improve flame retardance. The binder approach enables the vinyl ester resin to maintain its low

  15. Bond strength investigations and structural applicability of composite fiber-reinforced polymer (FRP) rebars

    Science.gov (United States)

    Kachlakev, Damian Ivanov

    The composite FRP rebars research at Oregon State University was initiated in 1993 principally to develop a non-metallic hollow reinforcement. It was recognized that the tensile properties of such reinforcement are unquestionably superior to steel, but its performance in concrete could be problematic. The bond between FRP rebars and concrete was identified as a critical area of concern. The purpose of this study is (i) to analyze a variety of FRP and steel reinforcing units; (ii) to advance the knowledge of bond mechanism, failure modes, and parameters influencing the bond strength; (iii) to compare composite rebars to conventional steel and to assess their applicability as reinforcing members. Commercially available FRP rebars were investigated. Particular emphasis was given to a hollow glass FRP rod designed at Oregon State University. Several parameters were investigated, including: failure mode, concrete compressive strength, rebar diameter and circumference/cross section ratio, embedment length, concrete cover, and microstructure of the composite rebars. It was recognized that the ASTM C234-90 pull-out standard is test of concrete strength. Therefore, a modified pull-out test was developed for evaluating the bond strength behavior. A newly developed European bond test procedure was compared with locally modified version of the pull-out method. The new procedure was used for the first time in the United States. The study demonstrated a phenomenon, not reported in the published research at this time, defined as a size effect. The size effects result in lower bond strength with increasing area of the interface between FRP bars and concrete. The next phase of the research was dedicated to the hollow glass FRP rebar. The goal was to compare its bond properties to conventional steel and solid FRP bars. The study led to two new phenomena not described in the literature previously. Results showed that the concrete compressive strength does not significantly affect the

  16. Fabrication of novel fiber reinforced aluminum composites by friction stir processing

    Energy Technology Data Exchange (ETDEWEB)

    Arab, Seyyed Mohammad; Karimi, Saeed; Jahromi, Seyyed Ahmad Jenabali, E-mail: jahromi@shirazu.ac.ir; Javadpour, Sirus; Zebarjad, Seyyed Mojtaba

    2015-04-24

    In this study, chopped and attrition milled high strength carbon, E-glass, and S-glass fibers have been used as the reinforcing agents in an aluminum alloy (Al1100) considered as the matrix. The Surface Metal Matrix Composites (SMMCs) then are produced by Friction Stir Processing (FSP). Tensile and micro-hardness examinations represent a magnificent improvement in the hardness, strength, ductility and toughness for all of the processed samples. Scanning Electron Micrographs reveal a proper distribution of the reinforcements in the matrix and a change in the fracture behavior of the FSPed specimens. The synergetic effects of reinforcing by fibers and Severe Plastic Deformation (SPD) lead to an extra ordinary improvement in the mechanical properties.

  17. Evaluation of mechanical properties of natural hybrid fibers, reinforced polyester composite materials

    Directory of Open Access Journals (Sweden)

    S. Kasiviswanathan

    2015-12-01

    Full Text Available The composite materials are replacing the traditional materials, because of its superior properties such as high tensile strength, low thermal expansion, high strength to weight ratio. The developments of new materials are on the anvil and are growing day by day. In this work the effect of glass fibre hybridization with the randomly oriented natural fibers has been evaluated. The sisal (S, banana (B, E-glass synthetic fibers were chopped and reinforced with polyester matrix. Six layers were prepared in the following stacking sequence of S/B/G, S/G/B, G/S/B, G/S/B/G/S/B/G, S/G/B//S/G/B, B/G/S/B/G/S. The mechanical properties like impact strength, flexural strength and tensile strength were investigated and compared. It was observed that the addition of two and three layer of glass fiber can improve the mechanical properties like tensile, Flexural and impact strength.

  18. Silicone Polymer Composites for Thermal Protection System: Fiber Reinforcements and Microstructures

    Science.gov (United States)

    2010-01-01

    R1 R3 R2 O Si R1 R2 O Si R1 R2 R3 n Homopolymer n=10,000 R1=R2= methyl , ethyl or vinyl Si R4 R4 HO O Si R5 R5 O Si R6 R6 O H n n=10,000 R4=R5=R6... methyl , ethyl , vinyl or phenyl Copolymer Figure 1. Chemical structures of ‘SM8000’ silicone polymer. 4 Journal of Composite Materials 0(0) A resin...and has been used extensively in our previous studies.29–31,34–37,41–44 The SSRM is a small-scale, liquid-fueled rocket motor burning kerosene oxygen

  19. Study of stinging nettle (urtica dioica l.) Fibers reinforced green composite materials : a review

    Science.gov (United States)

    Agus Suryawan, I. G. P.; Suardana, N. P. G.; Suprapta Winaya, I. N.; Budiarsa Suyasa, I. W.; Tirta Nindhia, T. G.

    2017-05-01

    Stinging Nettle (Urtica dioica L., latin) is a wild plant that grows in Indonesia, Asia, and Europe. Nettle in Bali, Indonesia is called as Lateng, Jelatang. Nettle plant has a very strong fiber and high fixed carbon. Nettle plants are covered with fine hairs, especially in the leaves and stems. When it is touched, it will release chemicals, sting and trigger inflammation that causes redness, itching, bumps and irritation to the skin. Nettle plants grow in the wild, regarded as a weed in the agricultural industry, easy to grow and snatch food from the parent plant. The main objective of this paper is to review of the potential nettle fibers and then explain about the potential of local nettle plant in Indonesia. Nettle is a plant group at the end of bast. Its plant fibers taken from the bark, as reinforcement in composite materials. Nettle fibers have three main advantages such as strong, lightweight and low environmental impact.

  20. Thermal and Mechanical Durability of Graphite-Fiber-Reinforced PMR-15 Composites

    Science.gov (United States)

    Bowles, Kenneth J.

    1997-01-01

    Earlier work, which reported relationships between compression properties and elevated temperature aging times and weight losses, also pointed out the apparent influence of surface layer formation and growth on the retention of compression properties during extended aging times. Since that time, studies have been directed toward evaluating the growth of the surface layer. This layer was found to change in its composition and features as the aging temperature changed. Microcracks and small voids initiated and advanced inward at all temperatures. Visible oxidation at the surface occurred only at temperatures above 260 C. Relationships between layer thickness and aging time and temperature were evaluated and empirically formulated. Then, the compression properties were graphically related to the surface layer thickness with excellent correlation. The surface layer was observed to influence the compression strength of thin samples only.

  1. Thermal and Mechanical Durability of Graphite-Fiber-Reinforced PMR-15 Composites. Revised

    Science.gov (United States)

    Bowles, Kenneth J.

    1998-01-01

    Earlier work, which reported relationships between compression properties and elevated temperature aging times and weight losses, also pointed out the apparent influence of surface layer formation and growth on the retention of compression properties during extended aging times. Since that time, studies have been directed toward evaluating the growth of the surface layer. This layer was found to change in its composition and features as the aging temperature changed. Microcracks and small voids initiated and advanced inward at all temperatures. Visible oxidation at the surface occurred only at temperatures above 260 deg. C. Relationships between layer thickness and aging time and temperature were evaluated and empirically formulated. Then, the compression properties were graphically related to the surface layer thickness with excellent correlation. The surface layer was observed to influence the compression strength of thin samples only.

  2. On Continuum Damage Modeling of Fiber Reinforced Viscoelastic Composites with Microcracks in terms of Invariants

    Directory of Open Access Journals (Sweden)

    Melek Usal

    2015-01-01

    Full Text Available A continuum damage model is developed for the linear viscoelastic behavior of composites with microcracks consisting of an isotropic matrix reinforced by two arbitrarily independent and inextensible fiber families. Despite the fact that the matrix material is isotropic, the model in consideration bears the characteristic of directed media included in the transverse isotropy symmetry group solely due to its fibers distributions and the existence of microcracks. Using the basic laws of continuum damage mechanics and equations belonging to kinematics and deformation geometries of fibers, the constitutive functions have been obtained. It has been detected as a result of the thermodynamic constraints that the stress potential function is dependent on two symmetric tensors and two vectors, whereas the dissipative stress function is dependent on four symmetric tensors and two vectors. To determine arguments of the constitutive functionals, findings relating to the theory of invariants have been used as a method because of the fact that isotropy constraint is imposed on the material. As a result the linear constitutive equations of elastic stress, dissipative stress, and strain energy density release rate have been written in terms of material coordinate description. Using these expressions, total stress has been found.

  3. Micromechanics and Structural Response of Functionally Graded, Particulate-Matrix, Fiber-Reinforced Composites.

    Science.gov (United States)

    Genin, Guy M; Birman, Victor

    2009-05-15

    Reinforcement of fibrous composites by stiff particles embedded in the matrix offers the potential for simple, economical functional grading, enhanced response to mechanical loads, and improved functioning at high temperatures. Here, we consider laminated plates made of such a material, with spherical reinforcement tailored by layer. The moduli for this material lie within relatively narrow bounds. Two separate moduli estimates are considered: a "two-step" approach in which fibers are embedded in a homogenized particulate matrix, and the Kanaun-Jeulin (2001) approach, which we re-derive in a simple way using the Benveniste (1988) method. Optimal tailoring of a plate is explored, and functional grading is shown to improve the performance of the structures considered. In the example of a square, simply supported, cross-ply laminated panel subjected to uniform transverse pressure, a modest functional grading offers significant improvement in performance. A second example suggests superior blast resistance of the panel achieved at the expense of only a small increase in weight.

  4. Macro-mechanical material model for fiber reinforced metal matrix composites

    CERN Document Server

    Banks-Sills, L

    1999-01-01

    The stress-strain behavior of a metal matrix composite reinforced with unidirectional, continuous and periodic fibers is investigated. Three-dimensional micro-mechanical analyses of a unit cell by means of the finite element method $9 and homogenization-localization are carried out. These calculations allow the determination of material behavior of the in-plane, as well as the fiber directions. The fibers are assumed to be elastic and the matrix elasto-plastic. $9 The matrix material is governed by a von Mises yield surface, isotropic hardening and an associated flow rule. With the aid of these analyses, the foundation to a macro-mechanical material model is presented which is employed to $9 consider an elementary problem. The model includes an anisotropic yield surface with isotropic hardening and an associated flow rule. A beam in bending containing square fibers under plane strain conditions is analyzed by means of $9 the model. Two cases are considered: one in which the fibers are symmetric with respect t...

  5. Effect of γ-irradiation on the optical and electrical properties of fiber reinforced composites

    Science.gov (United States)

    Anwar, Ahmad; Elfiky, Dalia; Ramadan, Ahmed M.; Hassan, G. M.

    2017-05-01

    The effect of gamma irradiation on the optical and electrical properties of the reinforced fiber polymeric based materials became an important issue. Fiberglass/epoxy and Kevlar fiber/epoxy were selected as investigated samples manufactured with hand lay-up without autoclave curing technique. The selected technique is simple and low cost while being rarely used in space materials production. The electric conductivity and dielectric constant for those samples were measured with increasing the gamma radiation dose. Moreover, the absorptivity, band gap and color change were determined. Fourier transform infrared (FTIR) was performed to each of the material's constituent to evaluate the change in the investigated materials due to radiation exposure dose. In this study, the change of electrical properties for both investigated materials showed a slight variation of the test parameters with respect to the gamma dose increase; this variation is placed in the insulators rang. The tested samples showed an insulator stable behavior during the test period. The change of optical properties for both composite specimens showed the maximum absorptivity at the gamma dose 750 kGy. These materials are suitable for structure materials and thermal control for orbital life less than 7 years. In addition, the transparency of epoxy matrix was degraded. However, there is no color change for either Kevlar fiber or fiberglass.

  6. Validation of Framework Code Approach to a Life Prediction System for Fiber Reinforced Composites

    Science.gov (United States)

    Gravett, Phillip

    1997-01-01

    The grant was conducted by the MMC Life Prediction Cooperative, an industry/government collaborative team, Ohio Aerospace Institute (OAI) acted as the prime contractor on behalf of the Cooperative for this grant effort. See Figure I for the organization and responsibilities of team members. The technical effort was conducted during the period August 7, 1995 to June 30, 1996 in cooperation with Erwin Zaretsky, the LERC Program Monitor. Phil Gravett of Pratt & Whitney was the principal technical investigator. Table I documents all meeting-related coordination memos during this period. The effort under this grant was closely coordinated with an existing USAF sponsored program focused on putting into practice a life prediction system for turbine engine components made of metal matrix composites (MMC). The overall architecture of the NMC life prediction system was defined in the USAF sponsored program (prior to this grant). The efforts of this grant were focussed on implementing and tailoring of the life prediction system, the framework code within it and the damage modules within it to meet the specific requirements of the Cooperative. T'he tailoring of the life prediction system provides the basis for pervasive and continued use of this capability by the industry/government cooperative. The outputs of this grant are: 1. Definition of the framework code to analysis modules interfaces, 2. Definition of the interface between the materials database and the finite element model, and 3. Definition of the integration of the framework code into an FEM design tool.

  7. Comparative Studies on the Mechanical Properties of Nonwoven- and Woven-Flax-Fiber-Reinforced Poly(Butylene Adipate-Co-Terephthalate)-Based Composite Laminates

    Science.gov (United States)

    Phongam, N.; Dangtungee, R.; Siengchin, S.

    2015-03-01

    Textile biocomposites made from woven- and nonwoven-flax-fiber-reinforced poly(butylene adipate-co-terephthalate) (PBAT) were prepared by compression molding using the film stacking method, and their tensile strength and stiffness, flexural strength and modulus, and impact strength were determined experimentally. The PBAT-based composites were subjected to water absorption tests. The mechanical properties of pure PBAT and the textile composites were compared, and the influence of flax weave styles on the properties were evaluated. The biocomposite reinforced with 4 × 4-plain weave fibers showed the highest strength and stiffness compared with those of the other textile biocomposites and pure PBAT.

  8. Study of noise reduction characteristics of composite fiber-reinforced panels, interior panel configurations, and the application of the tuned damper concept

    Science.gov (United States)

    Lameris, J.; Stevenson, S.; Streeter, B.

    1982-01-01

    The application of fiber reinforced composite materials, such as graphite epoxy and Kevlar, for secondary or primary structures developing in the commercial airplane industry was investigated. A composite panel program was initiated to study the effects of some of the parameters that affect noise reduction of these panels. The fiber materials and the ply orientation were chosen to be variables in the test program. It was found that increasing the damping characteristics of a structural panel will reduce the vibration amplitudes at resonant frequencies with attendant reductions in sound reduction. Test results for a dynamic absorber, a tuned damper, are presented and evaluated.

  9. Carbon nano fibers reinforced composites origami inspired mechanical metamaterials with passive and active properties

    Science.gov (United States)

    Kshad, Mohamed Ali E.; D’Hondt, Clement; Naguib, Hani E.

    2017-10-01

    unit cell made of composite polymers containing a low percentage of CNF were also investigated in this study, in which the shape memory effect test conducted on the origami unit cell.

  10. Study on Tribological Behavior of Fiber Reinforced PTFE Composites%纤维增强PTFE复合材料的摩擦磨损性能研究

    Institute of Scientific and Technical Information of China (English)

    朱仁鹏

    2013-01-01

    Fiber reinforced polyterafluoroethylene ( PTFE) composites were prepared by adding glass fiber (GF) and carbon fiber (CF) as fiber reinforcement. The friction and wear properties of GF/PTFE and CF/PTFE composites were investigated using the MM-200 tribometer. In addition, the effects of fiber reinforcements with different volume fractions, loads, slipping speeds on the friction and wear properties of composites were researched. Results showed the GF and CF can effectively improve the friction and wear properties of composites, the friction coefficient decreased gradually with the increase of fiber volume fraction. Moreover, the friction coefficient also decreased with the increase of the load, but the wear rate increased.%分别以玻璃纤维(GF)与碳纤维(CF)作为增强体制备了纤维增强聚四氟乙烯(PTFE)复合材料.利用MM-200型摩擦磨损试验机研究了GF/PTFE和CF/PTFE复合材料的摩擦磨损性能,以及不同体积分数的纤维增强体、不同载荷与滑动速度对复合材料的摩擦磨损性能的影响.结果表明:GF与CF的引入有效地提高了复合材料的摩擦磨损性能,随纤维体积分数的增加,复合材料的摩擦因数逐渐增加;另外,随载荷的增加,复合材料的摩擦因数亦逐渐降低,但磨损率增大.

  11. Effect of Fiber Reinforcement on the Response of Structural Members

    DEFF Research Database (Denmark)

    Fischer, Gregor; Li, Victor

    2007-01-01

    This paper describes a series of investigations on the effect of fiber reinforcement on the response of structural members in direct tension and flexure under reversed cyclic loading conditions. The design approach of the fiber reinforced cementitious composite is based on fracture mechanics prin...... to conventional reinforced concrete include improved composite integrity, energy dissipation, ductility, and damage tolerance....

  12. Bootstrap Method for Detecting Damage in Carbon Fiber Reinforced Plastic Using a Macro Fiber Composite Sensor

    OpenAIRE

    DJANSENA, Alradix; 田中, 宏明; 工藤, 亮

    2015-01-01

    CFRP has been used in aircraft structures for decades. Although CFRP is light, its laminationis its main weakness. We have developed a new method to increase the probability of detectingdelamination in carbon fiber reinforced plastic (CFRP) by narrowing the confidence interval ofthe changes in natural frequency. The changes in the natural frequency in delaminated CFRPare tiny compared with measurement errors. We use the bootstrap method, a statisticaltechnique that increases the estimation ac...

  13. 纤维及其复合材料老化机理研究进展%A Review on Aging Mechanisms of Fiber and Fiber Reinforced Composites

    Institute of Scientific and Technical Information of China (English)

    李树娟; 钟焕荣; 李智; 于亮

    2013-01-01

    Such environmental factors as hydrothermal , heat and UV have a negative effect on the mechanical properties of fiber and fiber reinforced composites ,making their strength and stiffness declined.The studies on the artificial climate aging ,thermal oxidation aging , photo oxidation aging , hydrothermal aging and ozone aging of fiber and fiber reinforced composites were summarized ,and the main aging mechanisms were introduced.In addition ,the disadvantage and trend of the studies on the aging of fiber and fiber reinforced composites were pointed out .%对于纤维及其复合材料而言,潮湿、遇热、光照等环境条件对其力学性能的影响明显,会导致其强度和刚度下降。本文阐述了国内外纤维及其复合材料的人工气候老化、热氧老化、光氧老化、湿热老化、臭氧老化等方面研究现状,提出了纤维及其复合材料老化的一些主要机理。在探讨了一些新研究手段的发展和取得的成果的基础上,进而展望了纤维及其复合材料老化研究存在的不足,并提出纤维及其复合材料老化研究的趋势。

  14. THRUST FORCE AND TORQUE IN DRILLING THE NATURAL FIBER REINFORCED POLYMER COMPOSITE MATERIALS AND EVALUATION OF DELAMINATION FACTOR FOR BONE GRAFT SUBSTITUTES -A WORK OF FICTION APPROACH

    Directory of Open Access Journals (Sweden)

    D. CHANDRAMOHAN

    2010-11-01

    Full Text Available This paper discusses about the Natural Fiber Reinforced Composite Materials contribution as bone implants. Biomaterial science is an interdisciplinary field that represents one of the most sophisticated trends in worldwide medical practice. In the last decades, researchers have developed new materials to improve the quality of human life. Owing to the frequent occurrence of bone fractures, it is important to develop a plate material for fixation on the fractured bone. These plate materials have to be lightweight, allow stiffness, and be biocompatible with humans. Drilling is the most frequently employed operation of secondary machining for fiber-reinforced materials, owing to the need for joining fractured bone by means of plate material in the field of orthopedics. An effort to utilize theadvantages offered by renewable resources for the development of biocomposite materials based on biopolymers and natural fibers has been made through fabrication of Natural fiber powdered material (Sisal (Agave sisalana, Banana (Musa sepientum, and Roselle (Hibiscus sabdariffa reinforced polymer composite plate material by using bio epoxy resin Grade 3554A and Hardner 3554B. Instead of orthopedics alloys such as Titanium, Cobalt chrome, Stainless steel, and Zirconium, this plate material can be used for internal fixationand aso external fixation on human body for fractured bone. The present work focuses on the prediction of thrust force and torque of the natural fiber reinforced polymer composite materials, and the values, compared with the Regression model and the Scheme of Delamination factor / zone using machine vision system, also discussed with the help of Scanning Electron Microscope [SEM].

  15. The effect of silanated and impregnated fiber on the tensile strength of E-glass fiber reinforced composite retainer

    Directory of Open Access Journals (Sweden)

    Niswati Fathmah Rosyida

    2015-12-01

    Full Text Available Background: Fiber reinforced composite (FRC is can be used in dentistry as an orthodontic retainer. FRC  still has a limitations because of to  a weak bonding between fibers and matrix. Purpose: This research was aimed to evaluate the effect of silane as coupling agent and fiber impregnation on the tensile strength of E-glass FRC. Methods: The samples of this research were classified into two groups each of which consisted of three subgroups, namely the impregnated fiber group (original, 1x addition of silane, 2x addition of silane and the non-impregnated fiber group (original, 1x addition of silane, 2x addition of silane. The tensile strength was measured by a universal testing machine. The averages of the tensile strength in all groups then were compared by using Kruskal Wallis and Mann Whitney post hoc tests. Results: The averages of the tensile strength (MPa in the impregnated fiber group can be known as follow; original impregnated fiber (26.60±0.51, 1x addition of silane (43.38±4.42, and 2x addition of silane (36.22±7.23. The averages of tensile strength (MPa in the non-impregnated fiber group can also be known as follow; original non-impregnated fiber (29.38±1.08, 1x addition of silane (29.38±1.08, 2x addition of silane (12.48±2.37. Kruskal Wallis test showed that there was a significant difference between the impregnated fiber group and the non-impregnated fiber group (p<0.05. Based on the results of post hoc test, it is also known that the addition of silane in the impregnated fiber group had a significant effect on the increasing of the tensile strength of E-glass FRC (p<0.05, while the addition of silane in the non-impregnated fiber group had a significant effect on the decreasing of the tensile strength of E-glass FRC. Conclusion: It can be concluded that the addition of silane in the non-silanated fiber group can increase the tensile strength of E-glass FRC, but the addition of silane in the silanated fiber group can

  16. Effects of hydrogen peroxide pretreatment and heat activation of silane on the shear bond strength of fiber-reinforced composite posts to resin cement

    OpenAIRE

    Pyun, Jung-Hoon; Shin, Tae-Bong; Lee, Joo-Hee; Ahn, Kang-Min; Kim, Tae-Hyung; Cha, Hyun-Suk

    2016-01-01

    PURPOSE To evaluate the effects of hydrogen peroxide pretreatment and heat activation of silane on the shear bond strength of fiber-reinforced composite posts to resin cement. MATERIALS AND METHODS The specimens were prepared to evaluate the bond strength of epoxy resin-based fiber posts (D.T. Light-Post) to dual-curing resin cement (RelyX U200). The specimens were divided into four groups (n=18) according to different surface treatments: group 1, no treatment; group 2, silanization; group 3,...

  17. 植物纤维工艺性能及其复合材料应用研究进展%Research on processing property of plant fiber and plant fiber reinforced composites

    Institute of Scientific and Technical Information of China (English)

    白一峰; 佟文清

    2013-01-01

    概述了近年来在植物纤维的渗透率、可压缩性等工艺性能方面的研究进展,揭示了植物纤维织物渗透性能及可压缩性能影响因素,并总结了多种植物纤维复合材料的研究进展,包括植物纤维/热塑性复合材料、植物纤维/可降解复合材料、植物纤维/热固性复合材料等.随着研究的不断深入,植物纤维复合材料会有更广泛的应用.%The study on processing property of plant fiber in recent years was outlined,such as impregnation property and compressibility,revealing affecting factors of processing property.Meanwhile,the development of different plant fiber reinforced composites was also summarized,including plant fiber reinforced thermoplastic composites,plant fiber reinforced biodegradable composites and plant fiber reinforced thermoset composites.With the research deepening of plant fiber,the plant fiber reinforced composites will be more widely used in future.

  18. Fracture behavior of block copolymer and graphene nanoplatelet modified epoxy and fiber reinforced/epoxy polymer composites

    Science.gov (United States)

    Kamar, Nicholas T.

    Glass and carbon fiber reinforced/epoxy polymer composites (GFRPs and CFRPs) have high strength-to-weight and stiffness-to-weight ratios. Thus, GFRPs and CFRPs are used to lightweight aircraft, marine and ground vehicles to reduce transportation energy utilization and cost. However, GFRP and CFRP matrices have a low resistance to crack initiation and propagation; i.e. they have low fracture toughness. Current methods to increase fracture toughness of epoxy and corresponding GFRP and CFRPs often reduce composite mechanical and thermomechanical properties. With the advent of nanotechnology, new methods to improve the fracture toughness and impact properties of composites are now available. The goal of this research is to identify the fracture behavior and toughening mechanisms of nanoparticle modified epoxy, GFRPs and CFRPs utilizing the triblock copolymer poly(styrene)-block-poly(butadiene)-block-poly(methylmethacrylate) (SBM) and graphene nanoplatelets (GnPs) as toughening agents. The triblock copolymer SBM was used to toughen the diglycidyl ether of bisphenol-A (DGEBA) resin cured with m-phenylenediamine (mPDA) and corresponding AS4-12k CFRPs. SBM self assembled in epoxy to form nanostructured domains leading to larger increases in fracture toughness, KQ (MPa*m 1/2) than the traditional, phase separating carboxyl-terminated butadiene-acrylonitrile (CTBN) rubber. Additionally, SBM increased the mode-I fracture toughness, GIc (J/m2) of CFRPs without corresponding reductions in composite three-point flexural properties and glass transition temperature (Tg). Fractography of SBM modified epoxy and CFRPs via scanning electron microscopy (SEM) showed that sub 100 nm spherical micelles cavitated to induce void growth and matrix shear yielding toughening mechanisms. Furthermore, SBM did not suppress epoxy Tg, while CTBN decreased Tg with both increasing concentration and acrylonitrile content. Graphene nanoplatelets (GnPs) consist of a few layers of graphene sheets, which

  19. Raman Study of Uncoated and p-BN/SiC-Coated Hi-Nicalon Fiber-Reinforced Celsian Matrix Composites. Part 1; Distribution and Nanostructure of Different Phases

    Science.gov (United States)

    Gouadec, Gwenael; Colomban, Philippe; Bansal, Narottam P.

    2000-01-01

    Hi-Nicalon fiber reinforced celsian matrix composites were characterized by Raman spectroscopy and imaging, using several laser wavelengths. Composite #1 is reinforced by as-received fibers while coatings of p-BN and SiC protect the fibers in composite #2. The matrix contains traces of the hexagonal phase of celsian, which is concentrated in the neighborhood of fibers in composite #1. Some free silicon was evident in the coating of composite #2 which might involve a {BN + SiC yields BNC + Si} "reaction" at the p-BN/SiC interface. Careful analysis of C-C peaks revealed no abnormal degradation of the fiber core in the composites.

  20. Restoring Nonvital Premolars with Composite Resin Onlays: Effect of Different Fiber-reinforced Composite Layers on Marginal Adaptation and Fracture Load.

    Science.gov (United States)

    Monaco, Carlo; Bortolotto, Tissiana; Arena, Antonio; Krejci, Ivo

    2015-12-01

    To evaluate the marginal adaptation and fracture load of composite resin onlays reinforced with different substructures. Thirty-two extracted, caries-free premolars were selected for this study and endodontically treated. Group 1 was used as the control group, and the teeth were restored only with as-manufactured composite resin overlays. Group 2 teeth were restored with composite resin overlays with 3 fiber-reinforced composite (FRC) layers placed horizontally on the bottom of the restoration. Group 3 teeth were restored with composite resin overlays with 6 fiber-reinforced composite (FRC) layers placed as in group 2. Group 4 teeth were restored with composite resin overlays and FRC placed with an anatomical design. All specimens underwent SEM evaluation of their marginal adaptation before and after thermocycling and cyclic mechanical loading. All specimens were then subjected to a fracture test, recording the value for the initial (IF) and final (FF) failure. Differences in the means were compared using matched-pairs t-tests and one-way ANOVA. The level of significance was set at α = 0.05. No statistically significant difference between the four groups in terms of marginal adaptation was observed at the tooth/luting composite and luting composite/overlay interfaces before and after loading. The fracture loads of IF and FF, from most to least resistant were: group 4 (1431.8 ± 294.3 N/1710.1 ± 326.6 N), group 3 (1428.1 ± 251.4 N/1467.9 ± 242.4 N), group 2 (852.6 ± 413.5 N/1058.1 ± 251.5 N) and group 1 (899.8 ± 352.7 N/923.5 ± 318.8 N). Significant differences (p = 0.026) were observed comparing group 1 to groups 2 and 3, and group 1 to 4. Three irreparable fractures were found in group 3, four in group 2, and five in groups 1 and 4. The presence or absence of reinforcement and the different configuration of the reinforcement fibers affect fracture strength but only partially the failure modality. The presence or absence of reinforcement does not alter