Comparison of the renewable transportation fuels, liquid hydrogen and methanol, with gasoline - energetic and economic aspects

International Nuclear Information System (INIS)

Specht, M.; Staiss, F.; Bandi, A.; Weimer, T.

1998-01-01

In this paper, the renewable energy vectors liquid hydrogen (LH 2 ) and methanol generated from atmospheric CO 2 are compared with the conventional crude oil-gasoline system. Both renewable concepts, liquid hydrogen and methanol, lead to a drastic CO 2 reduction compared to the fossil-based system. The comparison between the LH 2 and methanol vector for the transport sector shows nearly the same fuel cost and energy efficiency but strong infrastructure advantages for methanol. (author)

Renewable energies in the transport sector: Costs and possibilities

International Nuclear Information System (INIS)

Ajanovic, Amela; Haas, Reinhard

2007-01-01

Alternative fuels based on renewable energy sources, such as biodiesel, bioethanol and hydrogen from RES, have potential to reduce greenhouse gas emissions, climate change, to increase supply security and energy diversity. Transition from a fossil fuels based transport to future sustainable and clean transport is a long term and cost intensive process, especially for hydrogen use in transport. Hydrogen infrastructure is missing and most of hydrogen technologies are still at developing stage.This paper examines the economics of biofuels (bioethanol and biodiesel) and hydrogen production from renewable energy sources. The current and future costs of alternative fuels as well as the costs of the provided energy services are analysed in a dynamic framework till the year 2050. The goal is to identify the market chance of alternative fuels in a long term (till 2050). A rapid increase of fuel cell vehicles with hydrogen on the market is not expected before 2030, mainly because the costs of the fuel cells are still very high and because their efficiency, as well as the travelling range, is rather moderate.However, the use of alternative fuels in transport sector is very dependent on the political will. If political preferences, like e.g. zero-emission-vehicles, gain strong relevance this new fuels could accelerate its market penetration significantly

Efficiency versus cost of alternative fuels from renewable resources: outlining decision parameters

International Nuclear Information System (INIS)

Kaul, Sanjay; Edinger, Raphael

2004-01-01

In the discussion of traditional versus renewable energies and alternatives to conventional crude oil-based fuels in the transportation sector, efficiency calculations are but one decision making parameter. Comparing the assets and liabilities of fossil-based and renewable fuels in the transportation sector, further aspects such as centralized versus decentralized technologies, cost evaluations, taxation, and ecological/social benefits have to be taken into account. This paper outlines the driving parameters for shifting toward alternative fuels based on fossil or renewable resources and their use in innovative vehicle technologies such as advanced internal combustion and fuel cell electric drive systems. For the decision in favor or against an alternative fuel to be introduced to the mass market, automotive technologies and the energy supply system have to be examined in an integrated way. From an economic and technological perspective, some fuels may be even incompatible with the trend toward using renewable resources that have advantages in decentralized systems. Beyond efficiency calculations, political and industrial interests arise and may be influential to reshaping our currently crude oil-based mobility sector

The Integration of Sustainable Transport into Future Renewable Energy Systems in China

DEFF Research Database (Denmark)

Liu, Wen

use are largely lost in the current fossil fuel dominated energy systems. Sustainable transport development requires solutions from an overall renewable energy system in which integration of large-scale intermittent renewable energy needs assistance. Technologies of alternative vehicle fuels...... in transport may play a role in furthering such integration. The objective of this research is to make a contribution to the development of methodologies to identify and develop future sustainable transport systems as well as to apply such methodologies to the case of China. In particular, the methodological...... development focuses on 1) identifying suitable transport technologies and strategies based on renewable energy and 2) evaluating such technologies from the perspective of overall renewable energy system integration. For this purpose, a methodological framework involving the research fields of both...

A Renewably Powered Hydrogen Generation and Fueling Station Community Project

Science.gov (United States)

Lyons, Valerie J.; Sekura, Linda S.; Prokopius, Paul; Theirl, Susan

2009-01-01

The proposed project goal is to encourage the use of renewable energy and clean fuel technologies for transportation and other applications while generating economic development. This can be done by creating an incubator for collaborators, and creating a manufacturing hub for the energy economy of the future by training both white- and blue-collar workers for the new energy economy. Hydrogen electrolyzer fueling stations could be mass-produced, shipped and installed in collaboration with renewable energy power stations, or installed connected to the grid with renewable power added later.

Distributed renewable power from biomass and other waste fuels

Science.gov (United States)

Lyons, Chris

2012-03-01

The world population is continually growing and putting a burden on our fossil fuels. These fossil fuels such as coal, oil and natural gas are used for a variety of critical needs such as power production and transportation. While significant environmental improvements have been made, the uses of these fuels are still causing significant ecological impacts. Coal power production efficiency has not improved over the past thirty years and with relatively cheap petroleum cost, transportation mileage has not improved significantly either. With the demand for these fossil fuels increasing, ultimately price will also have to increase. This presentation will evaluate alternative power production methods using localized distributed generation from biomass, municipal solid waste and other waste sources of organic materials. The presentation will review various gasification processes that produce a synthetic gas that can be utilized as a fuel source in combustion turbines for clean and efficient combined heat and power. This fuel source can produce base load renewable power. In addition tail gases from the production of bio-diesel and methanol fuels can be used to produce renewable power. Being localized can reduce the need for long and costly transmission lines making the production of fuels and power from waste a viable alternative energy source for the future.

Risoe energy report 5. Renewable energy for power and transport

Energy Technology Data Exchange (ETDEWEB)

Larsen, Hans; Soenderberg Petersen, L. (eds.)

2006-11-15

The global energy policy scene today is dominated by three concerns, namely security of supply, climate change and energy for development and poverty alleviation. This is the starting point for Risoe Energy Report 5 that addresses status and trends in renewable energy, and gives an overview of global driving forces for transformation of the energy systems in the light of security of supply, climate change and economic growth. More specifically status and trends in renewable energy technologies, for broader applications in off grid power production (and heat) will be discussed. Furthermore the report will address wider introduction of renewable energy in the transport sector, for example renewable based fuels, hybrid vehicles, electric vehicles and fuel cell driven vehicles. (au)

Risoe energy report 5. Renewable energy for power and transport

International Nuclear Information System (INIS)

Larsen, Hans; Soenderberg Petersen, L.

2006-11-01

The global energy policy scene today is dominated by three concerns, namely security of supply, climate change and energy for development and poverty alleviation. This is the starting point for Risoe Energy Report 5 that addresses status and trends in renewable energy, and gives an overview of global driving forces for transformation of the energy systems in the light of security of supply, climate change and economic growth. More specifically status and trends in renewable energy technologies, for broader applications in off grid power production (and heat) will be discussed. Furthermore the report will address wider introduction of renewable energy in the transport sector, for example renewable based fuels, hybrid vehicles, electric vehicles and fuel cell driven vehicles. (au)

The system architecture for renewable synthetic fuels

DEFF Research Database (Denmark)

Ridjan, Iva

To overcome and eventually eliminate the existing heavy fossil fuels in the transport sector, there is a need for new renewable fuels. This transition could lead to large capital costs for implementing the new solutions and a long time frame for establishing the new infrastructure unless a suitable...... and production plants, so it is important to implement it in the best manner possible to ensure an efficient and flexible system. The poster will provide an overview of the steps involved in the production of synthetic fuel and possible solutions for the system architecture based on the current literature...

Renewable Hydrogen-Economically Viable: Integration into the U.S. Transportation Sector

Energy Technology Data Exchange (ETDEWEB)

Kurtz, Jennifer; Peters, Mike; Muratori, Matteo; Gearhart, Chris

2018-03-01

The U.S. transportation sector is expected to meet numerous goals in differing applications. These goals address security, safety, fuel source, emissions reductions, advanced mobility models, and improvements in quality and accessibility. Solutions to meeting these goals include a variety of alternative-fuel technologies, including batteries, fuel cells, synthetic fuels, and biofuels, as well as modifying how current transportation systems are used and integrating new systems, such as storing renewable energy. Overall, there are many combinations of problems, objectives, and solutions.

76 FR 37703 - Regulation of Fuels and Fuel Additives: 2012 Renewable Fuel Standards; Public Hearing

Science.gov (United States)

2011-06-28

... Regulation of Fuels and Fuel Additives: 2012 Renewable Fuel Standards; Public Hearing AGENCY: Environmental... hearing to be held for the proposed rule ``Regulation of Fuels and Fuel Additives: 2012 Renewable Fuel... be proposing amendments to the renewable fuel standard program regulations to establish annual...

DOE perspective on fuel cells in transportation

Energy Technology Data Exchange (ETDEWEB)

Kost, R.

1996-04-01

Fuel cells are one of the most promising technologies for meeting the rapidly growing demand for transportation services while minimizing adverse energy and environmental impacts. This paper reviews the benefits of introducing fuel cells into the transportation sector; in addition to dramatically reduced vehicle emissions, fuel cells offer the flexibility than use petroleum-based or alternative fuels, have significantly greater energy efficiency than internal combustion engines, and greatly reduce noise levels during operation. The rationale leading to the emphasis on proton-exchange-membrane fuel cells for transportation applications is reviewed as are the development issues requiring resolution to achieve adequate performance, packaging, and cost for use in automobiles. Technical targets for power density, specific power, platinum loading on the electrodes, cost, and other factors that become increasingly more demanding over time have been established. Fuel choice issues and pathways to reduced costs and to a renewable energy future are explored. One such path initially introduces fuel cell vehicles using reformed gasoline while-on-board hydrogen storage technology is developed to the point of allowing adequate range (350 miles) and refueling convenience. This scenario also allows time for renewable hydrogen production technologies and the required supply infrastructure to develop. Finally, the DOE Fuel Cells in Transportation program is described. The program, whose goal is to establish the technology for fuel cell vehicles as rapidly as possible, is being implemented by means of the United States Fuel Cell Alliance, a Government-industry alliance that includes Detroit`s Big Three automakers, fuel cell and other component suppliers, the national laboratories, and universities.

The role of renewable liquid transportation fuels in Canada's climate action plan: Pros and cons, and stages of development of ethanol, biodiesel, and thermal depolymerization oil

International Nuclear Information System (INIS)

Coxworth, E.

2003-04-01

The feasibility of using ethanol from grain as a partial replacement for gasoline is examined. Although ethanol is widely seen as a desirable renewable transportation fuel, there are concerns about the amount of fossil fuel energy used in its production, both at the farm and the factory level. Indeed, some people claim that there is, in fact, a net energy loss when ethanol is produced from grain, not to mention the concerns about the use of grain for fuel instead of food in a world where millions of people go hungry every day of their life. The emission from ethanol plants and the cost of producing ethanol from grain are related issues that cause concern. The report urges examination of alternatives to fermentation of plant materials such as gasification, and materials other than corn, such as woody material or hay which, although more complex and not yet commercially developed, are showing promise, and deserve further attention. Other renewable liquid transportation fuels such as biodiesel from canola oil, and thermal depolymerization oils that can be derived from a wide variety of waste renewable organic materials, are also suggested as potential fuel sources. Both of these appear promising and require testing to determine implications of further developing these technologies as replacement transportation fuels. The report contains a bibliography of 37 items for ethanol, 12 items for biodiesel, and two items for thermal depolymerization oil

77 FR 13009 - Regulation of Fuels and Fuel Additives: Identification of Additional Qualifying Renewable Fuel...

Science.gov (United States)

2012-03-05

... Regulation of Fuels and Fuel Additives: Identification of Additional Qualifying Renewable Fuel Pathways Under the Renewable Fuel Standard Program AGENCY: Environmental Protection Agency (EPA). ACTION: Withdrawal... Renewable Fuel Standard program regulations. Because EPA received adverse comment, we are withdrawing the...

The Palm Desert renewable [hydrogen] transportation system

Energy Technology Data Exchange (ETDEWEB)

Chamberlin, C.E.; Lehman, P. [Humboldt State Univ., Arcata, CA (United States). Schatz Energy Research Center

1998-08-01

This paper describes the Schatz Energy Research Center (SERC) progress on the Palm Desert Renewable Hydrogen Transportation System Project for the period June 1997 through May 1998. The project began in March 1996. The goal of the Palm Desert Project is to develop a clean and sustainable transportation system for a community. The project demonstrates the practical utility of hydrogen as a transportation fuel and the proton exchange membrane (PEM) fuel cell as a vehicle power system. The project includes designing and building 4 fuel cell powered vehicles, a solar hydrogen generating and refueling station, and a fuel cell vehicle diagnostic center. Over this last year, SERC has built a fuel cell powered neighborhood electric vehicle and delivered it to the City of Palm Desert. The design of the hydrogen refueling station is near completion and it is anticipated that construction will be complete in the fall of 1998. The vehicles are currently being refueled at a temporary refueling station. The diagnostic center is being designed and maintenance procedures as well as computer diagnostic programs for the fuel cell vehicles are being developed. City employees are driving the vehicles daily and monitoring data are being collected. The drivers are pleased with the performance of the vehicles.

78 FR 62462 - Regulation of Fuels and Fuel Additives: Modifications to Renewable Fuel Standard Program

Science.gov (United States)

2013-10-22

... renewable fuel is defined as fuel produced from renewable biomass that is used to replace or reduce the quantity of fossil fuel present in home heating oil or jet fuel.\\3\\ In essence, additional renewable fuel... of ``home heating oil.'' EPA determined that this term was ambiguous, and defined it by incorporating...

Optimized usage of NExBTL renewable diesel fuel - OPTIBIO

Energy Technology Data Exchange (ETDEWEB)

Nylund, N.-O. [VTT Technical Research Centre of Finland, Espoo (Finland); TEC TransEnergy Consulting Oy, Espoo (Finland)], email: nils-olof.nylund@vtt.fi, email: nils-olof.nylund@teconsulting.fi

2012-07-01

Buses are the backbone of many public transport systems, and typically have a long lifespan. Considering the need for switching to non-fossil fuels, municipalities increasingly want to raise the share of renewable fuels - also for their bus fleets - to reduce greenhouse gas emissions and fossil fuel imports. It is important for local decision-makers to understand which options are available and what the range of limitations and benefits of each. As the service life of buses is quite long, measures which can help improve the environmental performance of existing vehicles are important. When using conventional biodiesel there are technical limitations on how much fatty acid methyl ester (FAME) can be added to standard diesel fuel - in most cases replacement is below 10%. Further to this, some alternative fuels require new dedicated vehicles. The OPTIBIO project needed to explore how to optimise fuels that can be used in both existing and new vehicles, using high quality paraffinic renewable diesel (HVO) as fossil fuel replacement of up to 100%. The value, in addition to fuel replacement, would be the reduction of harmful emissions which are most crucial for urban air quality, namely nitrogen oxides and particulates.

Renewable hydrocarbon fuels from hydrothermal liquefaction: A techno-economic analysis

DEFF Research Database (Denmark)

Pedersen, Thomas Helmer; Hansen, Nick Høy; Pérez, Oscar Miralles

2018-01-01

This study demonstrates the economic feasibility of producing renewable transportation drop-in fuels from lignocellulosic biomass through hydrothermal liquefaction and upgrading. An Aspen Plus® process model is developed based on extensive experimental data to document a techno-economic assessmen...

Alternative transportation fuels in the USA: government hydrogen vehicle programs

International Nuclear Information System (INIS)

Cannon, J.S.

1993-01-01

The linkage between natural gas-based transportation and hydrogen-based transportation strategies, two clean burning gaseous fuels, provides a strong policy rationale for increased government sponsorship of hydrogen vehicle research and demonstration programs. Existing federal and state government hydrogen vehicle projects are discussed in this paper: research at the NREL, alternate-fueled buses, Renewable Hydrogen for the State of Hawaii program, New York state alternative transportation fuels program, Colorado program. 9 refs

Fuel and Chemicals from Renewable Alcohols

DEFF Research Database (Denmark)

Hansen, Jeppe Rass

2008-01-01

The present work entitled Fuel and Chemicals from Renewable Alcohols covers the idea of developing routes for producing sustainable fuel and chemicals from biomass resources. Some renewable alcohols are already readily available from biomass in significant amounts and thus the potential...... for these renewable alcohols, together with other primary renewable building blocks, has been highlighted in the introductory chapter. While the first chapter covers the general potential of a renewable chemical industry, the other chapters deal with particular possibilities. It is shown how ethanol and glycerol can...... be converted into hydrogen by steam reforming over nickel or ruthenium based catalysts. This process could be important in a future hydrogen society, where hydrogen can be utilized in high efficiency fuel cells. Hydrogen produced from biofeedstocks can also be used directly in the chemical industry, where...

Quality of renewable energy utilization in transport in Sweden

Energy Technology Data Exchange (ETDEWEB)

Lampinen, Ari

2015-04-01

Renewable energy utilization in transportation (RES-T) is a long way behind its utilization in power (RES-E) and heat (RES-H) sectors. International and national environmental policies have recently given a lot of emphasis on this problem. For that reason information is sought on how to implement solutions both politically and technologically. As Sweden is a global leader in this area, it can provide valuable examples. In 2012 Sweden became the first country to reach the binding requirement of the European Union for at least 10 % share for renewable energy in transport energy consumption. But qualitative development has been even stronger than quantitative. Among the success stories behind qualitative progress, most noteworthy are those created by innovative municipal policies. By 2030 Sweden aims to achieve fossil fuel independent road transport system and by 2050 completely carbon neutral transport system in all modes of transport.

Sustainable Transportation: Accelerating Widespread Adoption of Energy Efficient Vehicles & Fuels (Brochure)

Energy Technology Data Exchange (ETDEWEB)

2014-12-01

While energy efficient transportation strategies have the potential to simultaneously slash oil consumption and reduce greenhouse gas (GHG) emissions, a truly sustainable solution will require more than just putting drivers behind the wheels of new fuel-efficient cars. As the only national laboratory dedicated 100% to renewable energy and energy efficiency, the National Renewable Energy Laboratory (NREL) accelerates widespread adoption of high-performance, low-emission, energy-efficient passenger and freight vehicles, as well as alternative fuels and related infrastructure. Researchers collaborate closely with industry, government, and research partners, using a whole-systems approach to design better batteries, drivetrains, and engines, as well as thermal management, energy storage, power electronic, climate control, alternative fuel, combustion, and emission systems. NREL's sustainable transportation research, development, and deployment (RD&D) efforts are not limited to vehicles, roads, and fueling stations. The lab also explores ways to save energy and reduce GHGs by integrating transportation technology advancements with renewable energy generation, power grids and building systems, urban planning and policy, and fleet operations.

78 FR 12005 - Regulation of Fuels and Fuel Additives: 2013 Renewable Fuel Standards; Public Hearing

Science.gov (United States)

2013-02-21

... Regulation of Fuels and Fuel Additives: 2013 Renewable Fuel Standards; Public Hearing AGENCY: Environmental... EPA is announcing a public hearing to be held for the proposed rule ``Regulation of Fuels and Fuel Additives: 2013 Renewable Fuel Standards,'' which was published separately in the Federal Register on...

Biomethane: A Renewable Resource as Vehicle Fuel

Directory of Open Access Journals (Sweden)

Federica Cucchiella

2017-10-01

Full Text Available The European Union (EU has set a mandatory target for renewable fuels of 10% for each member state by 2020. Biomethane is a renewable energy representing an alternative to the use of fossil fuels in the transport sector. This resource is a solution to reach this target. Furthermore, it contributes to reducing carbon dioxide emissions, gives social benefits and increases the security supply. Sustainability is reached also when the economic opportunities are verified. This work studies the profitability of small plants of biomethane, which is sold as vehicle fuel using the Net Present Value (NPV and Discounted Payback Time (DPBT. The paper shows in detail the method used for the economic assessment of two typologies of feedstock recovered: (i municipal solid waste and (ii agricultural waste. Detailed information about the various parameters that affect the profitability of biomethane is given, and several case studies are analyzed as a function of two variables: subsidies and selling price. The results support the commercialization of small-scale plants, reducing also several environmental issues. The role of subsidies is strategic, and the profitability is verified only in some case studies

Interactions between California's Low Carbon Fuel Standard and the National Renewable Fuel Standard

International Nuclear Information System (INIS)

Whistance, Jarrett; Thompson, Wyatt; Meyer, Seth

2017-01-01

This study investigates the economic interactions between a national renewable fuel policy, namely the Renewable Fuel Standard (RFS) in the United States, and a sub-national renewable fuel policy, the Low Carbon Fuel Standard (LCFS) in California. The two policies have a similar objective of reducing greenhouse gas emissions, but the policies differ in the manner in which those objectives are met. The RFS imposes a hierarchical mandate of renewable fuel use for each year whereas the LCFS imposes a specific annual carbon-intensity reduction with less of a fuel specific mandate. We model the interactions using a partial-equilibrium structural model of agricultural and energy markets in the US and Rest-of-World regions. Our results suggest the policies are mutually reinforcing in that the compliance costs of meeting one of the requirements is lower in the presence of the other policy. In addition, the two policies combine to create a spatial shift in renewable fuel use toward California even though overall renewable fuel use remains relatively unchanged. - Highlights: • Results suggest the RFS and LCFS are mutually reinforcing. • Overall level of renewable fuel use is similar across scenarios. • Renewable fuel use shifts toward California in the presence of the LCFS. • Higher ethanol blend (e.g. E85) use also shifts toward California.

75 FR 37733 - Regulation of Fuels and Fuel Additives: Modifications to Renewable Fuel Standard Program

Science.gov (United States)

2010-06-30

... Regulation of Fuels and Fuel Additives: Modifications to Renewable Fuel Standard Program AGENCY... direct final rule to amend the Renewable Fuel Standard program requirements on May 10, 2010. Because EPA... Fuel Standard program requirements, published on May 10, 2010. We stated in that direct final rule that...

75 FR 14669 - Regulation of Fuels and Fuel Additives: Changes to Renewable Fuel Standard Program

Science.gov (United States)

2010-03-26

... RINs from producers of the renewable fuel. The obligated parties do not need lead time for construction... fuels and new limits on renewable biomass feedstocks. This rulemaking marks the first time that... advanced biofuel and multiple cellulosic-based fuels with their 60% threshold. Additional fuel pathways...

Comparison of fuel production costs for future transportation

DEFF Research Database (Denmark)

Ridjan, Iva; Mathiesen, Brian Vad; Connolly, David

The purpose of this poster is to provide an overview of fuel production costs for two types of synthetic fuels – methanol and methane, along with comparable costs for first and second generation biodiesel, two types of second generation bioethanol, and biogas. The model analysed is a 100% renewable...... scenario of Denmark for 2050, where the data for the transport sector has been changed to estimate the fuel production costs for eight different fuel pathways....

76 FR 18066 - Regulation of Fuels and Fuel Additives: Changes to Renewable Fuel Standard Program

Science.gov (United States)

2011-04-01

... ENVIRONMENTAL PROTECTION AGENCY 40 CFR Part 80 Regulation of Fuels and Fuel Additives: Changes to Renewable Fuel Standard Program CFR Correction In Title 40 of the Code of Federal Regulations, Parts 72 to...-generating foreign producers and importers of renewable fuels for which RINs have been generated by the...

Renewables vs fossil fuels

Energy Technology Data Exchange (ETDEWEB)

Adams, K. (Energy Research and Development Corporation (Australia))

1992-01-01

The paper examines some of the factors which will influence the future mix of energy from fossil fuels and renewable sources in Australia. Aspects covered include: the present energy situation; impact of environmental issues; potential for renewable energy; motivators for change; and research and development. It is concluded that the future for fossil fuels and renewable energy is dependent on a number of complex factors, many of which are currently unknown. The key factor is economic viability and that will be influenced by a range of factors such as policies of the Australian and overseas governments in relation to pollution and environment protection (reflected in the cost of meeting such requirements), exploration and production costs (also influenced by government policies), availability of supply, rate of technological development and the size of export markets. 8 refs., 2 figs., 1 tab.

The Design of a Renewable Hydrogen Fuel Infrastructure for London

International Nuclear Information System (INIS)

Parissis, O.; Bauen, A.

2006-01-01

The development of a least cost hydrogen infrastructure is key to the introduction of hydrogen fuel in road transport. This paper presents a generic framework for modelling the development of a renewable hydrogen infrastructure that can be applied to different cases and geographical regions. The model was designed by means of mixed integer linear programming and developed in MATLAB. It was applied to the case of London aiming to examine the possibilities of developing a renewable hydrogen infrastructure within a 50 years time horizon. The results presented here are preliminary results from a study looking at the least cost solutions to supplying hydrogen produced exclusively from renewable energy resources to large urban centres. (authors)

Fuel Mix Impacts from Transportation Fuel Carbon Intensity Standards in Multiple Jurisdictions

Science.gov (United States)

Witcover, J.

2017-12-01

Fuel carbon intensity standards have emerged as an important policy in jurisdictions looking to target transportation greenhouse gas (GHG) emissions for reduction. A carbon intensity standard rates transportation fuels based on analysis of lifecycle GHG emissions, and uses a system of deficits and tradable, bankable credits to reward increased use of fuels with lower carbon intensity ratings while disincentivizing use of fuels with higher carbon intensity ratings such as conventional fossil fuels. Jurisdictions with carbon intensity standards now in effect include California, Oregon, and British Columbia, all requiring 10% reductions in carbon intensity of the transport fuel pool over a 10-year period. The states and province have committed to grow demand for low carbon fuels in the region as part of collaboration on climate change policies. Canada is developing a carbon intensity standard with broader coverage, for fuels used in transport, industry, and buildings. This study shows a changing fuel mix in affected jurisdictions under the policy in terms of shifting contribution of transportation energy from alternative fuels and trends in shares of particular fuel pathways. It contrasts program designs across the jurisdictions with the policy, highlights the opportunities and challenges these pose for the alternative fuel market, and discusses the impact of having multiple policies alongside federal renewable fuel standards and sometimes local carbon pricing regimes. The results show how the market has responded thus far to a policy that incentivizes carbon saving anywhere along the supply chain at lowest cost, in ways that diverged from a priori policy expectations. Lessons for the policies moving forward are discussed.

Strategies for a road transport system based on renewable resources - The case of an import-independent Sweden in 2025

International Nuclear Information System (INIS)

Lindfeldt, Erik G.; Saxe, Maria; Magnusson, Mimmi; Mohseni, Farzad

2010-01-01

When discussing how society can decrease greenhouse gas emissions, the transport sector is often seen as posing one of the most difficult problems. In addition, the transport sector faces problems related to security of supply. The aim of this paper is to present possible strategies for a road transport system based on renewable energy sources and to illustrate how such a system could be designed to avoid dependency on imports, using Sweden as an example. The demand-side strategies considered include measures for decreasing the demand for transport, as well as various technical and non-technical means of improving vehicle fuel economy. On the supply side, biofuels and synthetic fuels produced from renewable electricity are discussed. Calculations are performed to ascertain the possible impact of these measures on the future Swedish road transport sector. The results underline the importance of powerful demand-side measures and show that although biofuels can certainly contribute significantly to an import-independent road transport sector, they are far from enough even in a biomass-rich country like Sweden. Instead, according to this study, fuels based on renewable electricity will have to cover more than half of the road transport sector's energy demand.

Meeting the U.S. renewable fuel standard: a comparison of biofuel pathways

Directory of Open Access Journals (Sweden)

Marc Y. Menetrez

2014-12-01

Full Text Available The production of renewable energy is undergoing rapid development. Ethanol primarily derived from corn and biodiesel made from recycled cooking oil and agricultural grains are established sources of renewable transportation fuel. Cellulosic ethanol production is increasing substantially, but at a rate below expectations. If future renewable fuel projections are to be accomplished, additional sources will be needed. Ideally, these sources should be independent of competing feedstock use such as food grains, and require a minimal footprint. Although the uses of algae seem promising, a number of demonstrations have not been economically successful in today‟s market. This paper identifies efforts being conducted on ethanol and biodiesel production and how algae might contribute to the production of biofuel in the United States. Additionally, the feedstock and land requirements of existing biofuel pathways are compared and discussed.

Fuel Handbook[Wood and other renewable fuels

Energy Technology Data Exchange (ETDEWEB)

Stroemberg, Birgitta [TPS Termiska Processer AB, Nykoeping (SE)] (ed.)

2006-03-15

This handbook on renewable fuels is intended for power and heat producers in Sweden. This fuel handbook provides, from a plant owner's perspective, a method to evaluate different fuels on the market. The fuel handbook concerns renewable fuels (but does not include household waste) that are available on the Swedish market today or fuels that have potential to be available within the next ten years. The handbook covers 26 different fuels. Analysis data, special properties, operating experiences and literature references are outlined for each fuel. [Special properties, operating experiences and literature references are not included in this English version] The handbook also contains: A proposed methodology for introduction of new fuels. A recommendation of analyses and tests to perform in order to reduce the risk of problems is presented. [The recommendation of analyses and tests is not included in the English version] A summary of relevant laws and taxes for energy production, with references to relevant documentation. [Only laws and taxes regarding EU are included] Theory and background to evaluate a fuel with respect to combustion, ash and corrosion properties and methods that can be used for such evaluations. Summary of standards, databases and handbooks on biomass fuels and other solid fuels, and links to web sites where further information about the fuels can be found. The appendices includes: A methodology for trial firing of fuels. Calculations procedures for, amongst others, heating value, flue gas composition, key number and free fall velocity [Free fall velocity is not included in the English version]. In addition, conversion routines between different units for a number of different applications are provided. Fuel analyses are presented in the appendix. (The report is a translation of parts of the report VARMEFORSK--911 published in 2005)

Nuclear-Renewable Hybrid System Economic Basis for Electricity, Fuel, and Hydrogen

Energy Technology Data Exchange (ETDEWEB)

Charles Forsberg; Steven Aumeier

2014-04-01

Concerns about climate change and altering the ocean chemistry are likely to limit the use of fossil fuels. That implies a transition to a low-carbon nuclear-renewable electricity grid. Historically variable electricity demand was met using fossil plants with low capital costs, high operating costs, and substantial greenhouse gas emissions. However, the most easily scalable very-low-emissions generating options, nuclear and non-dispatchable renewables (solar and wind), are capital-intensive technologies with low operating costs that should operate at full capacities to minimize costs. No combination of fully-utilized nuclear and renewables can meet the variable electricity demand. This implies large quantities of expensive excess generating capacity much of the time. In a free market this results in near-zero electricity prices at times of high nuclear renewables output and low electricity demand with electricity revenue collapse. Capital deployment efficiency—the economic benefit derived from energy systems capital investment at a societal level—strongly favors high utilization of these capital-intensive systems, especially if low-carbon nuclear renewables are to replace fossil fuels. Hybrid energy systems are one option for better utilization of these systems that consumes excess energy at times of low prices to make some useful product.The economic basis for development of hybrid energy systems is described for a low-carbon nuclear renewable world where much of the time there are massivequantities of excess energy available from the electric sector.Examples include (1) high-temperature electrolysis to generate hydrogen for non-fossil liquid fuels, direct use as a transport fuel, metal reduction, etc. and (2) biorefineries.Nuclear energy with its concentrated constant heat output may become the enabling technology for economically-viable low-carbon electricity grids because hybrid nuclear systems may provide an economic way to produce dispatachable variable

[U.S. renewable fuel standard implementation mechanism and market tracking].

Science.gov (United States)

Kang, Liping; Earley, Robert; An, Feng; Zhang, Yu

2013-03-01

U.S. Renewable Fuel Standard (RFS) is a mandatory policy for promoting the utilization of biofuels in road transpiration sector in order to reduce the country's dependency on foreign oil and greenhouse gas emissions. U.S. Environmental Protection Agency (EPA) defines the proportion of renewable fuels according to RFS annual target, and requests obligated parties such like fossil fuel refiner, blenders and importer in the U.S. to complete Renewable Volume Obligation (RVO) every year. Obligated parties prove they have achieved their RVO through a renewable fuels certification system, which generates Renewable Identification Numbers (RINs) for every gallon of qualified renewable fuels produced or imported into U.S., RINs is a key for tracking renewable fuel consumption, which in turn is a key for implementing the RFS in the U.S., separated RINs can be freely traded in market and obligated parties could fulfill their RVO through buying RINs from other stakeholders. This briefing paper highlights RFS policy implementing mechanism and marketing tracking, mainly describes importance of RINs, and the method for generating and tracking RINs by both government and fuels industry participants.

Perspective on renewable fuels policy April 2002

International Nuclear Information System (INIS)

2002-04-01

Natural Resources Canada (NRCan) has initiated a constructive dialogue on its ethanol policy, and the Canadian Petroleum Products Institute (CPPI) is supportive of the government's efforts in that regard and encourages this dialogue to continue. CPPI believes that it is important to provide sound information to policy makers. Before policy decisions are made, all stakeholders must be fully involved in the process and aware of the implications of the various options open for discussion. In this document, it is stated that significant additional government intervention in the form of higher subsidies and/or mandate is required to increase Canadian demand and push market penetration of fuel ethanol. One of the benefits from the utilization of ethanol fuel resides in the reduction of greenhouse gas emissions. However, the cost effectiveness of ethanol in terms of greenhouse gas emissions reductions indicates that other strategies are less expensive. It was mentioned that ethanol production technology requires a thorough evaluation. The situation in the United States is reviewed. Negotiations recently took place that produced a comprehensive proposal on renewable fuels, and includes: a renewable fuels mandate, funding for leaking underground storage tanks programs, maintenance of the toxic air pollution reductions, and a study of harmonization of Federal, state and local fuel requirements, among others. It was indicated that the Canadian situation is not reflected in this proposal, since most of the policy drivers for the American proposal are not relevant to the Canadian situation. The considerations for Canadian policy makers include two options: investment in production facilities that are widely distributed throughout the country, or transporting ethanol across vast distances at a higher cost. The conclusion calls for further federal and provincial intervention

Energy system aspects of hydrogen as an alternative fuel in transport

International Nuclear Information System (INIS)

Ramesohl, Stephan; Merten, Frank

2006-01-01

Considering the enormous ecological and economic importance of the transport sector the introduction of alternative fuels-together with drastic energy efficiency gains-will be a key to sustainable mobility, nationally as well as globally. However, the future role of alternative fuels cannot be examined from the isolated perspective of the transport sector. Interactions with the energy system as a whole have to be taken into account. This holds both for the issue of availability of energy sources as well as for allocation effects, resulting from the shift of renewable energy from the stationary sector to mobile applications. With emphasis on hydrogen as a transport fuel for private passenger cars, this paper discusses the energy systems impacts of various scenarios introducing hydrogen fueled vehicles in Germany. It identifies clear restrictions to an enhanced growth of clean hydrogen production from renewable energy sources (RES). Furthermore, it points at systems interdependencies that call for a priority use of RES electricity in stationary applications. Whereas hydrogen can play an increasing role in transport after 2030 the most important challenge is to exploit short-mid-term potentials of boosting car efficiency

Fuel cells as renewable energy sources

International Nuclear Information System (INIS)

Cacciola, G.; Passalacqua, E.

2001-01-01

The technology level achieved in fuel cell (FC) systems in the last years has significantly increased the interest of various manufacturing industries engaged in energy production and distribution even under the perspectives that this technology could provide. Today, the fuel cells (FCs) can supply both electrical and thermal energy without using moving parts and with a high level of affordability with respect to the conventional systems. FCs can utilise every kind of fuel such as hydrocarbons, hydrogen available from the water through renewable sources (wind, solar energy), alcohol etc. Thus, they may find application in many field ranging from energy production in large or small plants to the cogeneration systems for specific needs such as for residential applications, hospitals, industries, electric vehicles and portable power sources. Low temperature polymer electrolyte fuel cells (PEFC, DMFC) are preferred for application in the field of transportation and portable systems. The CNR-ITAE research activity in this field concerns the development of technologies, materials and components for the entire system: electrocatalysts, conducting supports, electrolytes, manufacturing technologies for the electrodes-electrolyte assemblies and the attainment of fuel cells with high power densities. Furthermore, some activities have been devoted to the design and realisation of PEFC fuel cell prototypes with rated power lower than I kW for stationary and mobile applications [it

Waste-to-Fuel: A Case Study of Converting Food Waste to Renewable Natural Gas as a Transportation Fuel

Energy Technology Data Exchange (ETDEWEB)

Mintz, Marianne [Argonne National Lab. (ANL), Argonne, IL (United States); Tomich, Matthew [Argonne National Lab. (ANL), Argonne, IL (United States)

2017-05-01

This case study explores the production and use of renewable compressed natural gas (R-CNG)—derived from the anaerobic digestion (AD) of organic waste—to fuel heavy-duty refuse trucks and other natural gas vehicles in Sacramento, California.

Alternative Fuels Data Center: Landfills Convert Biogas Into Renewable

Science.gov (United States)

Natural Gas Landfills Convert Biogas Into Renewable Natural Gas to someone by E-mail Share Alternative Fuels Data Center: Landfills Convert Biogas Into Renewable Natural Gas on Facebook Tweet about Alternative Fuels Data Center: Landfills Convert Biogas Into Renewable Natural Gas on Twitter Bookmark

Environmental economics of lignin derived transport fuels.

Science.gov (United States)

Obydenkova, Svetlana V; Kouris, Panos D; Hensen, Emiel J M; Heeres, Hero J; Boot, Michael D

2017-11-01

This paper explores the environmental and economic aspects of fast pyrolytic conversion of lignin, obtained from 2G ethanol plants, to transport fuels for both the marine and automotive markets. Various scenarios are explored, pertaining to aggregation of lignin from several sites, alternative energy carries to replace lignin, transport modalities, and allocation methodology. The results highlight two critical factors that ultimately determine the economic and/or environmental fuel viability. The first factor, the logistics scheme, exhibited the disadvantage of the centralized approach, owing to prohibitively expensive transportation costs of the low energy-dense lignin. Life cycle analysis (LCA) displayed the second critical factor related to alternative energy carrier selection. Natural gas (NG) chosen over additional biomass boosts well-to-wheel greenhouse gas emissions (WTW GHG) to a level incompatible with the reduction targets set by the U.S. renewable fuel standard (RFS). Adversely, the process' economics revealed higher profits vs. fossil energy carrier. Copyright © 2017 The Author(s). Published by Elsevier Ltd.. All rights reserved.

Generation of transportation fuel from solid municipal waste plastics

Energy Technology Data Exchange (ETDEWEB)

Sarker, Moinuddin

2010-09-15

Transportation fuels derived from fossil fuels are subjected to the price fluctuations of the global marketplace, and constitute a major expense in the operation of a vehicle. Emissions from the evaporation and combustion of these fuels contribute to a range of environmental problems, causing poor air quality and emitting greenhouse gases that contribute to global warming. Alternative fuels created from domestic sources have been proposed as a solution to these problems, and many fuels are being developed based on biomass and other renewable sources. Natural State Research, Inc. developed different alternative hydrocarbon fuel which is produced from waste plastic materials.

Cow Power: A Case Study of Renewable Compressed Natural Gas as a Transportation Fuel

Energy Technology Data Exchange (ETDEWEB)

Mintz, Marianne [Argonne National Lab. (ANL), Argonne, IL (United States); Tomich, Matthew [Argonne National Lab. (ANL), Argonne, IL (United States)

2017-08-01

This case study explores the production and use of renewable compressed natural gas (R-CNG)—derived from the anaerobic digestion (AD) of dairy manure—to fuel 42 heavy-duty milk tanker trucks operating in Indiana, Michigan, Tennessee, and Kentucky.

Future combustion technology for synthetic and renewable fuels in compression ignition engines (REFUEL). Final report

Energy Technology Data Exchange (ETDEWEB)

Aakko-Saksa, P.; Brink, A.; Happonen, M. [and others

2012-07-01

This domestic project, Future Combustion Technology for Synthetic and Renewable Fuels in Compression Ignition Engines (ReFuel), was part of a Collaborative Task 'Future Combustion Technology for Synthetic and Renewable Fuels in Transport' of International Energy Agency (IEA) Combustion Agreement. This international Collaborative Task is coordinated by Finland. The three-year (2009-2011) prooject was a joint research project with Aalto University (Aalto), Tampere University of Technology (TUT), Technical Research Centre of Finland (VTT) and Aabo Akademi University (AAU). The project was funded by TEKES, Waertsilae Oyj, Agro Sisu Power, Aker Arctic Technology Oy and the research partners listed above. Modern renewable diesel fuels have excellent physical and chemical properties, in comparison to traditional crude oil based fuels. Purely paraffinic fuels do not contain aromatic compounds and they are totally sulphur free. Hydrotreated Vegetable Oil (HVO) was studied as an example of paraffinic high cetane number (CN) diesel fuels. HVO has no storage and low temperature problems like the fatty acid methyl esters (FAMEs) have. The combustion properties are better than those of crude oil based fuels and FAME, because they have very high cetane numbers and contain no polyaromatic hydrocarbons (PAH). With low HVO density, viscosity and distillation temperatures, these advantageous properties allow far more advanced combustion strategies, such as very high exhaust gas recirculation (EGR) rates or extreme Miller timings, than has been possible with current fossil fuels. The implementation of these advanced combustion technologies, together with the novel renewable diesel fuel, brought significant nitrogen oxides (NO{sub x}), particulate matter (PM) emission reductions with no efficiency losses. (orig.)

Improving Catalyst Efficiency in Bio-Based Hydrocarbon Fuels; NREL (National Renewable Energy Laboratory)

Energy Technology Data Exchange (ETDEWEB)

None

2015-06-01

This article investigates upgrading biomass pyrolysis vapors to form hydrocarbon fuels and chemicals using catalysts with different concentrations of acid sites. It shows that greater separation of acid sites makes catalysts more efficient at producing hydrocarbon fuels and chemicals. The conversion of biomass into liquid transportation fuels has attracted significant attention because of depleting fossil fuel reserves and environmental concerns resulting from the use of fossil fuels. Biomass is a renewable resource, which is abundant worldwide and can potentially be exploited to produce transportation fuels that are less damaging to the environment. This renewable resource consists of cellulose (40–50%), hemicellulose (25–35%), and lignin (16–33%) biopolymers in addition to smaller quantities of inorganic materials such as silica and alkali and alkaline earth metals (calcium and potassium). Fast pyrolysis is an attractive thermochemical technology for converting biomass into precursors for hydrocarbon fuels because it produces up to 75 wt% bio-oil,1 which can be upgraded to feedstocks and/or blendstocks for further refining to finished fuels. Bio-oil that has not been upgraded has limited applications because of the presence of oxygen-containing functional groups, derived from cellulose, hemicellulose and lignin, which gives rise to high acidity, high viscosity, low heating value, immiscibility with hydrocarbons and aging during storage. Ex situ catalytic vapor phase upgrading is a promising approach for improving the properties of bio-oil. The goal of this process is to reject oxygen and produce a bio-oil with improved properties for subsequent downstream conversion to hydrocarbons.

Applying life-cycle assessment to low carbon fuel standards-How allocation choices influence carbon intensity for renewable transportation fuels

International Nuclear Information System (INIS)

Kaufman, Andrew S.; Meier, Paul J.; Sinistore, Julie C.; Reinemann, Douglas J.

2010-01-01

The Energy Independence and Security Act (EISA) of 2007 requires life-cycle assessment (LCA) for quantifying greenhouse gas emissions (GHGs) from expanded U.S. biofuel production. To qualify under the Renewable Fuel Standard, cellulosic ethanol and new corn ethanol must demonstrate 60% and 20% lower emissions than petroleum fuels, respectively. A combined corn-grain and corn-stover ethanol system could potentially satisfy a major portion of renewable fuel production goals. This work examines multiple LCA allocation procedures for a hypothetical system producing ethanol from both corn grain and corn stover. Allocation choice is known to strongly influence GHG emission results for corn-ethanol. Stover-derived ethanol production further complicates allocation practices because additional products result from the same corn production system. This study measures the carbon intensity of ethanol fuels against EISA limits using multiple allocation approaches. Allocation decisions are shown to be paramount. Under varying approaches, carbon intensity for corn ethanol was 36-79% that of gasoline, while carbon intensity for stover-derived ethanol was -10% to 44% that of gasoline. Producing corn-stover ethanol dramatically reduced carbon intensity for corn-grain ethanol, because substantially more ethanol is produced with only minor increases in emissions. Regulatory considerations for applying LCA are discussed.

Compliance with annual obligation 2011 for renewable energy transport and obligation with regard to fuels and air pollution; Naleving jaarverplichting 2011 hernieuwbare energie vervoer en verplichting brandstoffen luchtverontreiniging

Energy Technology Data Exchange (ETDEWEB)

NONE

2012-06-15

The renewable energy transport regulation is to ensure that an increasing percentage of the fuels used for road transport and mobile machinery consists of renewable energy. In the year 2011 the renewable energy obligation was 4.25% (biofuels) on an energy basis. The fuels air pollution regulation is to ensure that less CO2 is emitted throughout the chain from fuel production to combustion in the engine. For 2011 there is a reporting obligation, but is no emission reduction obligation. The year 2011 was the first year in which companies have submitted data to the Dutch Emissions Authority (NEA) on biofuels. This report was prepared on the basis of these submitted data [Dutch] De regelgeving hernieuwbare energie vervoer is erop gericht dat een steeds groter percentage van de brandstoffen die worden ingezet voor het wegverkeer en mobiele machines bestaat uit hernieuwbare energie. In 2011 bedroeg de jaarverplichting hernieuwbare energie 4,25% op energiebasis. De regelgeving brandstoffen luchtverontreiniging is erop gericht dat er steeds minder CO2 wordt uitgestoten in de gehele keten vanaf de productie van de brandstof tot en met de verbranding in de motor. Voor 2011 is er een rapportageplicht, er is geen emissiereductieverplichting. Het jaar 2011 was het eerste jaar waarin bedrijven de gegevens over hun uitgeslagen biobrandstoffen bij de NEa hebben ingediend. Dit rapport is opgesteld op basis van deze ingediende gegevens.

Evaluating the viability of dimethyl carbonate as an alternative fuel for the transportation sector.

Science.gov (United States)

2017-06-01

Some of the most important questions in the development of sustainable transportation are : identify fuels that will reduce emissions, provide diversification from fossil fuels, reduce : greenhouse gas emissions, be produced from renewable sources, a...

Alternative Fuels Data Center: Renewable Natural Gas From Landfill Powers

Science.gov (United States)

Refuse Vehicles Renewable Natural Gas From Landfill Powers Refuse Vehicles to someone by E-mail Share Alternative Fuels Data Center: Renewable Natural Gas From Landfill Powers Refuse Vehicles on Facebook Tweet about Alternative Fuels Data Center: Renewable Natural Gas From Landfill Powers Refuse

Advanced reactors and novel reactions for the conversion of triglyceride based oils into high quality renewable transportation fuels

Science.gov (United States)

Linnen, Michael James

Sustainable energy continues to grow more important to all societies, leading to the research and development of a variety of alternative and renewable energy technologies. Of these, renewable liquid transportation fuels may be the most visible to consumers, and this visibility is further magnified by the long-term trend of increasingly expensive petroleum fuels that the public consumes. While first-generation biofuels such as biodiesel and fuel ethanol have been integrated into the existing fuel infrastructures of several countries, the chemical differences between them and their petroleum counterparts reduce their effectiveness. This gives rise to the development and commercialization of second generation biofuels, many of which are intended to have equivalent properties to those of their petroleum counterparts. In this dissertation, the primary reactions for a second-generation biofuel process, known herein as the University of North Dakota noncatalytic cracking process (NCP), have been studied at the fundamental level and improved. The NCP is capable of producing renewable fuels and chemicals that are virtually the same as their petroleum counterparts in performance and quality (i.e., petroleum-equivalent). In addition, a novel analytical method, FIMSDIST was developed which, within certain limitations, can increase the elution capabilities of GC analysis and decrease sample processing times compared to other high resolution methods. These advances are particularly useful for studies of highly heterogeneous fuel and/or organic chemical intermediates, such as those studied for the NCP. However the data from FIMSDIST must be supplemented with data from other methods such as for certain carboxylic acid, to provide accurate, comprehensive results, From a series of TAG cracking experiments that were performed, it was found that coke formation during cracking is most likely the result of excessive temperature and/or residence time in a cracking reactor. Based on this

Renewable Energy Policy Fact sheet - Slovakia

International Nuclear Information System (INIS)

2017-09-01

The EurObserv'ER policy profiles give a snapshot of the renewable energy policy in the EU Member States. The main support scheme for electricity from renewable energy sources is a feed-in tariff scheme. For operators of photovoltaics (PV) and onshore wind installations an investment subsidy instrument is available as well. Besides, the sale of generated renewable electricity is incentivized by an exemption from excise duty. Also renewable heat production installations are eligible for an investment subsidy instrument. For renewable transport fuels a bio-fuels quota scheme is on place. Moreover, producers/suppliers of bio-fuels and petroleum fuels blended with bio-fuels benefit from a fiscal incentive

Does a renewable fuel standard for biofuels reduce climate costs?

Energy Technology Data Exchange (ETDEWEB)

Greaker, Mads; Hoel, Michael; Rosendahl, Knut Einar

2012-07-01

Recent contributions have questioned whether biofuels policies actually lead to emissions reductions, and thus lower climate costs. In this paper we make two contributions to the literature. First, we study the market effects of a renewable fuel standard. Opposed to most previous studies we model the supply of fossil fuels taking into account that fossil fuels is a non-renewable resource. Second, we model emissions from land use change explicitly when we evaluate the climate effects of the renewable fuel standard. We find that extraction of fossil fuels most likely will decline initially as a consequence of the standard. Thus, if emissions from biofuels are sufficiently low, the standard will have beneficial climate effects. Furthermore, we find that the standard tends to reduce total fuel (i.e., oil plus biofuels) consumption initially. Hence, even if emissions from biofuels are substantial, climate costs may be reduced. Finally, if only a subset of countries introduce a renewable fuel standard, there will be carbon leakage to the rest of the world. However, climate costs may decline as global extraction of fossil fuels is postponed.(Author)

Is biomass always a renewable fuel as guaranteed?

International Nuclear Information System (INIS)

Veski, Rein

1999-01-01

Full text: In official EU documents the terms biomass, biofuels, renewable energy resources have not yet been defined unambiguously. In the respective statistical reports peat falls, according to earlier classification traditions, under the subdivision NACE 10 together with coal and lignite (fossil fuels). No NACE classification has been applied in the renewable energy industry. This is probably why no unanimity has been achieved in classifying peat as a renewable fuel. Besides wind, solar, geothermal and water energy, biomass belongs to renewable energy sources as well. The situation is also regrettably equivocal because the terms biomass and biofuel (biological fuel) were used only recently and are continuously used as a wholly dry mass of animal or plant population (kg/m 2 or kg/m 3 ) and as manure or other organic waste as a source of heat delivered in an anaerobic decay in greenhouses, respectively. This uncertainty in using the terms under consideration leads sometimes to a nonsense in official documents. For example, in paragraph 2 of the Energy Act, the provision concerning fuel does not apply to wood, peat and biofuel. According to this statement wood and peat are not classified as biofuels (the correct statement is: wood, peat and other biofuels). Another statement of the Act (paragraph 28 1 The obligation to purchase alternatively produced electric power) declares that an energy trader dominating the market is required to purchase electric power from traders connected to its network and who produce such power from water, wind or solar energy, biomass, waste gases or waste material. According to this statement waste material is not classified as biomass either. As wood and peat are not classified as biofuel in Paragrapg 2 (4) and paragraph 28 1 , an energy trader dominating the market must not purchase electricity produced from wood and peat. By way of a remark: almost 99 % of Estonia's electric energy was produced from oil shale. It means that in Estonia

Fuel-cycle greenhouse gas emissions impacts of alternative transportation fuels and advanced vehicle technologies

International Nuclear Information System (INIS)

Wang, M. Q.

1998-01-01

At an international conference on global warming, held in Kyoto, Japan, in December 1997, the United States committed to reduce its greenhouse gas (GHG) emissions by 7% over its 1990 level by the year 2012. To help achieve that goal, transportation GHG emissions need to be reduced. Using Argonne's fuel-cycle model, I estimated GHG emissions reduction potentials of various near- and long-term transportation technologies. The estimated per-mile GHG emissions results show that alternative transportation fuels and advanced vehicle technologies can help significantly reduce transportation GHG emissions. Of the near-term technologies evaluated in this study, electric vehicles; hybrid electric vehicles; compression-ignition, direct-injection vehicles; and E85 flexible fuel vehicles can reduce fuel-cycle GHG emissions by more than 25%, on the fuel-cycle basis. Electric vehicles powered by electricity generated primarily from nuclear and renewable sources can reduce GHG emissions by 80%. Other alternative fuels, such as compressed natural gas and liquefied petroleum gas, offer limited, but positive, GHG emission reduction benefits. Among the long-term technologies evaluated in this study, conventional spark ignition and compression ignition engines powered by alternative fuels and gasoline- and diesel-powered advanced vehicles can reduce GHG emissions by 10% to 30%. Ethanol dedicated vehicles, electric vehicles, hybrid electric vehicles, and fuel-cell vehicles can reduce GHG emissions by over 40%. Spark ignition engines and fuel-cell vehicles powered by cellulosic ethanol and solar hydrogen (for fuel-cell vehicles only) can reduce GHG emissions by over 80%. In conclusion, both near- and long-term alternative fuels and advanced transportation technologies can play a role in reducing the United States GHG emissions

Fuel-cycle greenhouse gas emissions impacts of alternative transportation fuels and advanced vehicle technologies.

Energy Technology Data Exchange (ETDEWEB)

Wang, M. Q.

1998-12-16

At an international conference on global warming, held in Kyoto, Japan, in December 1997, the United States committed to reduce its greenhouse gas (GHG) emissions by 7% over its 1990 level by the year 2012. To help achieve that goal, transportation GHG emissions need to be reduced. Using Argonne's fuel-cycle model, I estimated GHG emissions reduction potentials of various near- and long-term transportation technologies. The estimated per-mile GHG emissions results show that alternative transportation fuels and advanced vehicle technologies can help significantly reduce transportation GHG emissions. Of the near-term technologies evaluated in this study, electric vehicles; hybrid electric vehicles; compression-ignition, direct-injection vehicles; and E85 flexible fuel vehicles can reduce fuel-cycle GHG emissions by more than 25%, on the fuel-cycle basis. Electric vehicles powered by electricity generated primarily from nuclear and renewable sources can reduce GHG emissions by 80%. Other alternative fuels, such as compressed natural gas and liquefied petroleum gas, offer limited, but positive, GHG emission reduction benefits. Among the long-term technologies evaluated in this study, conventional spark ignition and compression ignition engines powered by alternative fuels and gasoline- and diesel-powered advanced vehicles can reduce GHG emissions by 10% to 30%. Ethanol dedicated vehicles, electric vehicles, hybrid electric vehicles, and fuel-cell vehicles can reduce GHG emissions by over 40%. Spark ignition engines and fuel-cell vehicles powered by cellulosic ethanol and solar hydrogen (for fuel-cell vehicles only) can reduce GHG emissions by over 80%. In conclusion, both near- and long-term alternative fuels and advanced transportation technologies can play a role in reducing the United States GHG emissions.

40 CFR 80.1430 - Requirements for exporters of renewable fuels.

Science.gov (United States)

2010-07-01

... of renewable fuel in the blend. (2) Determination of the renewable portion of the blend using Method... method as approved by the EPA. (3) Assuming the maximum concentration of the renewable fuel in the blend... its neat form or blended with gasoline or diesel, that is exported from any of the regions described...

75 FR 42237 - Regulation of Fuels and Fuel Additives: 2011 Renewable Fuel Standards

Science.gov (United States)

2010-07-20

... Based on a Thermochemical Platform 3. Hybrid Thermochemical/Biochemical Processes 4. Pyrolysis and Depolymerization a. Pyrolysis Diesel Fuel and Gasoline b. Catalytic Depolymerization 5. Catalytic Reforming of... result would be that additional volumes of conventional renewable fuel, such as corn-starch ethanol...

77 FR 72746 - Regulation of Fuels and Fuel Additives: Modifications to Renewable Fuel Standard and Diesel...

Science.gov (United States)

2012-12-06

... Fuels and Fuel Additives: Modifications to Renewable Fuel Standard and Diesel Sulfur Programs AGENCY... Fuel Standard (``RFS'') program under section 211(o) of the Clean Air Act. The direct final rule also... marine diesel fuel produced by transmix processors, and the fuel marker requirements for 500 ppm sulfur...

The unstudied barriers to widespread renewable energy deployment: Fossil fuel price responses

International Nuclear Information System (INIS)

Foster, Edward; Contestabile, Marcello; Blazquez, Jorge; Manzano, Baltasar; Workman, Mark; Shah, Nilay

2017-01-01

Renewable energy policy focuses on supporting the deployment of renewable power generators so as to reduce their costs through scale economies and technological learning. It is expected that, once cost parity with fossil fuel generation is achieved, a transition towards renewable power should continue without the need for further renewable energy subsidies. However, this reasoning implicitly assumes that the cost of fossil fuel power generation does not respond to the large scale penetration of renewable power. In this paper we build a standard economic framework to test the validity of this assumption, particularly in the case of coal and gas fired power generation. We find that it is likely that the cost of fossil fuel power generation will respond to the large scale penetration of renewables, thus making the renewable energy transition slower or more costly than anticipated. More analysis is needed in order to be able to quantify this effect, the occurrence of which should be considered in the renewable energy discourse. - Highlights: • Renewables are increasingly competing with fossil fuel power generation. • This may have various effects on the fossil fuel generation value chain. • One such possible effect is a response of fossil fuel prices to renewables deployment. • We have tested this hypothesis using a supply-demand analytical framework. • We found that the effect is likely to occur and should be further investigated.

Fuel Cells for Balancing Fluctuation Renewable Energy Sources

DEFF Research Database (Denmark)

Mathiesen, Brian Vad

2007-01-01

In the perspective of using fuel cells for integration of fluctuating renewable energy the SOFCs are the most promising. These cells have the advantage of significantly higher electricity efficiency than competing technologies and fuel flexibility. Fuel cells in general also have the advantage of...... with hydrogen production or electric cars, and on the other hand using biomass and bio fuels [11]. Fuel cells can have an important role in these future energy systems.......In the perspective of using fuel cells for integration of fluctuating renewable energy the SOFCs are the most promising. These cells have the advantage of significantly higher electricity efficiency than competing technologies and fuel flexibility. Fuel cells in general also have the advantage...... flexibility, such as SOFCs, heat pumps and heat storage technologies are more important than storing electricity as hydrogen via electrolysis in energy systems with high amounts of wind [12]. Unnecessary energy conversions should be avoided. However in future energy systems with wind providing more than 50...

Fuel transporting device

International Nuclear Information System (INIS)

Shiratori, Hirozo.

1979-01-01

Purpose: In a liquid-metal cooled reactor, to reduce the waiting time of fuel handling apparatuses and shorten the fuel exchange time. Constitution: A fuel transporting machine is arranged between a reactor vessel and an out-pile storage tank, thereby dividing the transportation line of the pot for contracting fuel and transporting the same. By assuming such a construction, the flow of fuel transportation which has heretofore been carried out through fuel transportation pipes is not limited to one direction but the take-out of fuels from the reactor and the take-in thereof from the storage tank can be carried out constantly, and much time is not required for fuel exchange. (Kamimura, M.)

Conceptual evaluation of hybrid energy system comprising wind-biomass-nuclear plants for load balancing and for production of renewable synthetic transport fuels

International Nuclear Information System (INIS)

Carlsson, Johan; Purvins, Arturs; Papaioannou, Ioulia T.; Shropshire, David; Cherry, Robert S.

2014-01-01

Future energy systems will increasingly need to integrate variable renewable energy in order to reduce greenhouse gas emissions from power production. Addressing this trend the present paper studies how a hybrid energy systems comprising aggregated wind farms, a biomass processing plant, and a nuclear cogeneration plant could support high renewable energy penetration. The hybrid energy system operates so that its electrical output tends to meet demand. This is achieved mainly through altering the heat-to-power ratio of the nuclear reactor and by using excess electricity for hydrogen production through electrolysis. Hybrid energy systems with biomass treatment processes, i.e. drying, torrefaction, pyrolysis and synthetic fuel production were evaluated. It was shown that the studied hybrid energy system comprising a 1 GWe wind farm and a 347 MWe nuclear reactor could closely follow the power demand profile with a standard deviation of 34 MWe. In addition, on average 600 m"3 of bio-gasoline and 750 m"3 bio-diesel are produced daily. The reduction of greenhouse gas emissions of up to 4.4 MtCO_2eq annually compared to power generation and transport using conventional fossil fuel sources. (author)

Inter renewal travelling wave reactor with rotary fuel columns

International Nuclear Information System (INIS)

Terai, Yuzo

2016-01-01

To realize the COP21 decision, this paper proposes Inter Renewal Travelling Wave Reactor that bear high burn-up rate 50% and product TRU fuel efficiently. The reactor is based on 4S Fast Reactor and has Reactor Fuel Columns as fuel assemblies that equalize temperature in the fuel assembly so that fewer structure is need to restrain thermal transformation. To equalize burn-up rate of all fuel assemblies in the reactor, each rotary fuel column has each motor-lifter. The rotary fuel column has two types (Cylinder type and Heat Pipe type using natrium at 15 kPa which supply high temperature energy for Ultra Super Critical power plant). At 4 years cycle all rotary fuel columns of the reactor are renewed by the metallurgy method (vacuum re-smelting) and TRU fuel is gotten from the water fuel. (author)

Nuclear fuel transport and particularly spent fuel transport

International Nuclear Information System (INIS)

Lenail, B.

1986-01-01

Nuclear material transport is an essential activity for COGEMA linking the different steps of the fuel cycle transport systems have to be safe and reliable. Spent fuel transport is more particularly examined in this paper because the development of reprocessing plant. Industrial, techmical and economical aspects are reviewed [fr

Electric vehicles and renewable energy in the transport sector - energy system consequences. Main focus: Battery electric vehicles and hydrogen based fuel cell vehicles

DEFF Research Database (Denmark)

Nielsen, L.H.; Jørgensen K.

2000-01-01

The aim of the project is to analyse energy, environmental and economic aspects of integrating electric vehicles in the future Danish energy system. Consequences of large-scale utilisation of electric vehicles are analysed. The aim is furthermore toillustrate the potential synergistic interplay...... between the utilisation of electric vehicles and large-scale utilisation of fluctuating renewable energy resources, such as wind power. Economic aspects for electric vehicles interacting with a liberalisedelectricity market are analysed. The project focuses on battery electric vehicles and fuel cell...... vehicles based on hydrogen. Based on assumptions on the future technical development for battery electric vehicles, fuel cell vehicles on hydrogen, and forthe conventional internal combustion engine vehicles, scenarios are set up to reflect expected options for the long-term development of road transport...

Renewable Energy Policy Fact sheet - Czech Republic

International Nuclear Information System (INIS)

2017-09-01

The EurObserv'ER policy profiles give a snapshot of the renewable energy policy in the EU Member States. For electricity from renewable sources of energy main support instruments are feed-in tariffs (FIPs) and feed-in premiums (FiPs). Operators of renewable energy installation have to make a choice for either the applicable FiT or the corresponding FiP. Except for hydro installations with a capacity of 10 MW, the FiT/FiP scheme has been closed for new installations generating electricity from renewables. Hydro power installations with a size ≤ 10 MW are also eligible for subsidies. Installations for production of renewable heat can apply for subsidies granted by the European Regional Development Fund (ERDF) and are exempt from real estate tax. A renewable heating obligation for buildings is in place and a regulation on the use of renewable heating by public authorities. The main support scheme for renewable transport fuels is a renewable transport quota scheme. This scheme obliges companies importing or producing gasoline or automotive diesel to ensure that bio-fuels make up a defined percentage of their overall annual sales volume of automotive fuels. Besides, bio-fuels are exempt from a consumption tax

Renewable Energy Policy Fact sheet - Luxembourg

International Nuclear Information System (INIS)

2017-09-01

The EurObserv'ER policy profiles give a snapshot of the renewable energy policy in the EU Member States. Main support instruments for incentivising electricity from renewable energy sources are feed-in tariffs and feed-in premiums. A subsidy instrument is used as well. Households operating small solar installations are entitled to tax benefits. Renewable heat production is promoted through four subsidy instruments. Renewable transport fuels are promoted by way of a bio-fuels blending quota scheme

The production of hydrogen fuel from renewable sources and its role in grid operations

International Nuclear Information System (INIS)

Barton, John; Gammon, Rupert

2010-01-01

Understanding the scale and nature of hydrogen's potential role in the development of low carbon energy systems requires an examination of the operation of the whole energy system, including heat, power, industrial and transport sectors, on an hour-by-hour basis. The Future Energy Scenario Assessment (FESA) software model used for this study is unique in providing a holistic, high resolution, functional analysis, which incorporates variations in supply resulting from weather-dependent renewable energy generators. The outputs of this model, arising from any given user-definable scenario, are year round supply and demand profiles that can be used to assess the market size and operational regime of energy technologies. FESA was used in this case to assess what - if anything - might be the role for hydrogen in a low carbon economy future for the UK. In this study, three UK energy supply pathways were considered, all of which reduce greenhouse gas emissions by 80% by 2050, and substantially reduce reliance on oil and gas while maintaining a stable electricity grid and meeting the energy needs of a modern economy. All use more nuclear power and renewable energy of all kinds than today's system. The first of these scenarios relies on substantial amounts of 'clean coal' in combination with intermittent renewable energy sources by year the 2050. The second uses twice as much intermittent renewable energy as the first and virtually no coal. The third uses 2.5 times as much nuclear power as the first and virtually no coal. All scenarios clearly indicate that the use of hydrogen in the transport sector is important in reducing distributed carbon emissions that cannot easily be mitigated by Carbon Capture and Storage (CCS). In the first scenario, this hydrogen derives mainly from steam reformation of fossil fuels (principally coal), whereas in the second and third scenarios, hydrogen is made mainly by electrolysis using variable surpluses of low-carbon electricity. Hydrogen

The production of hydrogen fuel from renewable sources and its role in grid operations

Science.gov (United States)

Barton, John; Gammon, Rupert

Understanding the scale and nature of hydrogen's potential role in the development of low carbon energy systems requires an examination of the operation of the whole energy system, including heat, power, industrial and transport sectors, on an hour-by-hour basis. The Future Energy Scenario Assessment (FESA) software model used for this study is unique in providing a holistic, high resolution, functional analysis, which incorporates variations in supply resulting from weather-dependent renewable energy generators. The outputs of this model, arising from any given user-definable scenario, are year round supply and demand profiles that can be used to assess the market size and operational regime of energy technologies. FESA was used in this case to assess what - if anything - might be the role for hydrogen in a low carbon economy future for the UK. In this study, three UK energy supply pathways were considered, all of which reduce greenhouse gas emissions by 80% by 2050, and substantially reduce reliance on oil and gas while maintaining a stable electricity grid and meeting the energy needs of a modern economy. All use more nuclear power and renewable energy of all kinds than today's system. The first of these scenarios relies on substantial amounts of 'clean coal' in combination with intermittent renewable energy sources by year the 2050. The second uses twice as much intermittent renewable energy as the first and virtually no coal. The third uses 2.5 times as much nuclear power as the first and virtually no coal. All scenarios clearly indicate that the use of hydrogen in the transport sector is important in reducing distributed carbon emissions that cannot easily be mitigated by Carbon Capture and Storage (CCS). In the first scenario, this hydrogen derives mainly from steam reformation of fossil fuels (principally coal), whereas in the second and third scenarios, hydrogen is made mainly by electrolysis using variable surpluses of low-carbon electricity. Hydrogen

A case study of renewable energy for Hawaii

Energy Technology Data Exchange (ETDEWEB)

Phillips, V D; Takahashi, P K [Hawaii Natural Energy Inst., Manoa, HI (United States); Chuveliov, A V [I.V. Kurchatov Inst. of Atomic Energy. Moscow (SU)

1992-02-01

A hypothetical fuel-energy system based on indigenous, renewable resources to achieve energy self-sufficiency in Hawaii by the end of the 21st century is presented. In this case study, renewable resources would provide sufficient energy for a projected total energy consumption of approximately 335 x 10{sup 6}GJ from approximately 15 GWe of installed capacity in the year 2100. The renewable fuel-energy system would feature methanol-from-biomass to meet liquid fuel requirements for surface transportation and for the industrial, commercial, and residential sectors; hydrogen via electrolysis in liquid form for air transportation and as a gaseous fuel for industrial purposes; and electricity generated from geothermal, ocean thermal, wind, and photovoltaic sources for all power applications. A green economic analysis indicates that between the years 1987 and 2100 the switch to this hypothetical renewable fuel-energy system would require expenditures of approximately $400 billion (1986 U.S. dollars), representing a saving of approximately $200 billion over continuing a business-as-usual fuel-energy system based on imported fossil fuels. (author).

Renewable Energy Policy Fact sheet - Croatia

International Nuclear Information System (INIS)

2017-07-01

The EurObserv'ER policy profiles give a snapshot of the renewable energy policy in the EU Member States. Electricity from renewable sources is promoted through a premium tariff (and a guaranteed feed-in tariff for installations of less than 30 kW), allocated through tenders. Soft loans and subsidies for renewable energy projects are also provided. Renewable energy sources for heating purposes only are not promoted through a national support scheme. A training programme for RES installers aims at promoting the development, installation and usage of power generating and heating installations based on renewables. The main promotion scheme in the field of renewable transport fuels is a bio-fuels quota scheme. Additionally, the state provides bio-fuels incentives taking the form of a tax credits mechanism

Fueling Wisconsin's economy with renewable energy

International Nuclear Information System (INIS)

Clemmer, S.

1995-01-01

A dynamic macroeconomic model of the Wisconsin economy is used to estimate the economic impacts of displacing a portion of future investment in fossil fuel power plants (coal and natural gas) with renewable energy resources (biomass, wind, solar and hydro). The results show that renewable energy investments produce over three times more jobs, income and economic activity than the same amount of electricity generated from coal and natural gas power plants. Between 1995 and 2020, a 75% increase in renewable energy use generates approximately 65,000 more job-years of employment, $1.6 billion in higher disposable income and a $3.1 billion increase in gross regional product than conventional power plant investments. This includes the effects of a 0.3% average annual increase in electricity prices from renewable energy investments

40 CFR 80.1426 - How are RINs generated and assigned to batches of renewable fuel by renewable fuel producers or...

Science.gov (United States)

2010-07-01

... contaminants that are impractical to remove and are related to customary feedstock production and transport... Biodiesel, and renewable diesel Soy bean oil;Oil from annual covercrops; One of the following:Trans... renewable biomass andpetroleum. Non-food grade corn oil Biodiesel, and renewable diesel Soy bean oil; One of...

The renewable energies market in the United Kingdom

International Nuclear Information System (INIS)

2001-08-01

Targets for renewable energies in the United Kingdom (U.K.) have been set at 10 per cent of the total electricity produced by 2010. Out of a total annual consumption of 364 000 GWh, renewable energies now provide 2.8 per cent of the electricity in the U.K. As a result, market growth over the next decade is expected to reach 250 per cent. Several specific new regulations have also been introduced to support these targets. U.K. electricity supply companies must now set percentages from renewable sources, and new fiscal measures penalizing fossil-fuel consumption while promoting renewables are included in these new regulations. Extra funding to support renewables research and development, pilot and demonstration projects, marketing and dissemination activities to increase renewables take-up in the country has been earmarked. Renewables application in the filed of transportation fuels has been identified. Duty cuts on biodiesel fuel were made following the recent Green Fuel Challenge consultation exercise. Once demonstration projects are proposed, additional duty cuts for other biofuels might be made. There should be considerable expansion of the U.K. renewables market. Biomass, for primary energy and transportation fuels, offshore wind, small-scale hydro and photovoltaics (PVs) are all sectors where opportunities exist. Fuel cell and wave/tidal technologies are likely to show some promise once they make it to the commercial/mass production phase. 35 refs., 4 tabs., 2 figs

Development of materials for use in solid oxid fuel cells anodes using renewable fuels in direct operation

International Nuclear Information System (INIS)

Lima, D.B.P.L. de; Florio, D.Z. de; Bezerra, M.E.O.

2016-01-01

Fuel cells produce electrical current from the electrochemical combustion of a gas or liquid (H2, CH4, C2H5OH, CH3OH, etc.) inserted into the anode cell. An important class of fuel cells is the SOFC (Solid Oxide Cell Fuel). It has a ceramic electrolyte that transports protons (H +) or O-2 ions and operating at high temperatures (500-1000 °C) and mixed conductive electrodes (ionic and electronic) ceramics or cermets. This work aims to develop anodes for fuel cells of solid oxide (SOFC) in order to direct operations with renewable fuels and strategic for the country (such as bioethanol and biogas). In this context, it becomes important to study in relation to the ceramic materials, especially those that must be used in high temperatures. Some types of double perovskites such as Sr2MgMoO6 (or simply SMMO) have been used as anodes in SOFC. In this study were synthesized by the polymeric precursor method, analyzed and characterized different ceramic samples of families SMMO, doped with Nb, this is: Sr2 (MgMo)1-xNbxO6 with 0 ≤ x ≤ 0.2. The materials produced were characterized by various techniques such as, thermal analysis, X-ray diffraction and scanning electron microscopy, and electrical properties determined by dc and ac measurements in a wide range of temperature, frequency and partial pressure of oxygen. The results of this work will contribute to a better understanding of advanced ceramic properties with mixed driving (electronic and ionic) and contribute to the advancement of SOFC technology operating directly with renewable fuels. (author)

Climate consequences of low-carbon fuels: The United States Renewable Fuel Standard

International Nuclear Information System (INIS)

Hill, Jason; Tajibaeva, Liaila; Polasky, Stephen

2016-01-01

A common strategy for reducing greenhouse gas (GHG) emissions from energy use is to increase the supply of low-carbon alternatives. However, increasing supply tends to lower energy prices, which encourages additional fuel consumption. This “fuel market rebound effect” can undermine climate change mitigation strategies, even to the point where efforts to reduce GHG emissions by increasing the supply of low-carbon fuels may actually result in increased GHG emissions. Here, we explore how policies that encourage the production of low-carbon fuels may result in increased GHG emissions because the resulting increase in energy use overwhelms the benefits of reduced carbon intensity. We describe how climate change mitigation strategies should follow a simple rule: a low-carbon fuel with a carbon intensity of X% that of a fossil fuel must displace at least X% of that fossil fuel to reduce overall GHG emissions. We apply this rule to the United States Renewable Fuel Standard (RFS2). We show that absent consideration of the fuel market rebound effect, RFS2 appears to reduce GHG emissions, but once the fuel market rebound effect is factored in, RFS2 actually increases GHG emissions when all fuel GHG intensity targets are met. - Highlights: • Low-carbon fuels partially displace petroleum via fuel market rebound effect. • Synthesis of recent analyses shows incomplete petroleum displacement by biofuels. • Fuel market rebound effect can reduce or reverse climate benefit of low-carbon fuels. • Fossil fuel displacement must exceed relative carbon footprint of a low-carbon fuel. • The Renewable Fuel Standard increases greenhouse gas emissions when mandate is met.

Renewable energies in France: main results in 2008

International Nuclear Information System (INIS)

2008-01-01

This article comments the evolution of renewable energy production in France in 2008: hydro energy, wind energy, solar photovoltaic energy, renewable thermal energy (like biogas, solar thermal energy, geothermal energy, heat pumps, urban waste, and wood) and agro-fuels. It also comments the consumption of thermal renewable energies and agro-fuels by different sectors (housing and office buildings, industry, and transports)

Safe handling of renewable fuels and fuel mixtures

Energy Technology Data Exchange (ETDEWEB)

Wilen, C; Rautalin, A [VTT Energy, Espoo (Finland)

1997-12-01

VTT Energy has for several years carried out co-operation with many European research institutes on contractional basis on safety issues of fuels handling. A two-year co-operational project between VTT Energy and these research institutes was started in EU`s JOULE 3 programme in 1996, the total budget of which is 6.9 million FIM. Dust explosion testing method for `difficult` fuels, and for tests at elevated pressures and temperatures, will be developed in the task `Safe handling of renewable fuels and fuel mixtures`. Self- ignition and dust-explosion characteristics will be generated for wood and agro-biomass based biomasses and for the mixtures of them and coal. Inertization requirements will be studied, and the quenching method, combined with partial inertization, will be tested in 1.0 m{sup 3} test equipment. The ignition properties of the fuels under normal and elevated pressures will be characterised with thermobalances. The self-ignition tests with wood and forest residue dusts at 25 bar pressure have been carried out as scheduled. In addition to this, several fuels have undergone thermobalance tests, sieve analyses and microscopic studies for the characterisation of the fuels

Investigation of the effects of renewable diesel fuels on engine performance, combustion, and emissions

KAUST Repository

Ogunkoya, Dolanimi

2015-01-01

A study was undertaken to investigate renewable fuels in a compression-ignition internal combustion engine. The focus of this study was the effect of newly developed renewable fuels on engine performance, combustion, and emissions. Eight fuels were investigated, and they include diesel, jet fuel, a traditional biodiesel (fatty acid methyl ester: FAME), and five next generation biofuels. These five fuels were derived using a two-step process: hydrolysis of the oil into fatty acids (if necessary) and then a thermo-catalytic process to remove the oxygen via a decarboxylation reaction. The fuels included a fed batch deoxygenation of canola derived fatty acids (DCFA), a fed batch deoxygenation of canola derived fatty acids with varying amounts of H2 used during the deoxygenation process (DCFAH), a continuous deoxygenation of canola derived fatty acids (CDCFA), fed batch deoxygenation of lauric acid (DLA), and a third reaction to isomerize the products of the deoxygenated canola derived fatty acid alkanes (IPCF). Diesel, jet fuel, and biodiesel (FAME) have been used as benchmarks for comparing with the newer renewable fuels. The results of the experiments show slightly lower mechanical efficiency but better brake specific fuel consumption for the new renewable fuels. Results from combustion show shorter ignition delays for most of the renewable (deoxygenated) fuels with the exception of fed batch deoxygenation of lauric acid. Combustion results also show lower peak in-cylinder pressures, reduced rate of increase in cylinder pressure, and lower heat release rates for the renewable fuels. Emission results show an increase in hydrocarbon emissions for renewable deoxygenated fuels, but a general decrease in all other emissions including NOx, greenhouse gases, and soot. Results also demonstrate that isomers of the alkanes resulting from the deoxygenation of the canola derived fatty acids could be a potential replacement to conventional fossil diesel and biodiesel based on the

Renewable and nuclear sources of energy reduce the share of fossil fuels

International Nuclear Information System (INIS)

Koprda, V.

2009-01-01

In this paper author presents a statistical data use of nuclear energy, renewable sources and fossil fuels in the share of energy production in the Slovak Republic. It is stated that use of nuclear energy and renewable sources reduce the share of fossil fuels.

Renewable and nuclear sources of energy decreases of share of fossil fuels

International Nuclear Information System (INIS)

Koprda, V.

2009-01-01

In this paper author presents a statistical data use of nuclear energy, renewable sources and fossil fuels in the share of energy production in the Slovak Republic. It is stated that use of nuclear energy and renewable sources decreases of share of fossil fuels.

Renewable energy for Canada's northern communities - quantifying potential fuel savings

International Nuclear Information System (INIS)

Brothers, C.

1998-01-01

The probable impact of renewable energy technologies on fuel consumption in Canada's remote northern communities was discussed. These communities currently meet their electricity requirements using expensive diesel powered generators. It was noted that change to renewable energy in Canada's remote communities will only be made if the economic benefits can be clearly demonstrated. A study was conducted in Cambridge Bay, Northwest Territories, in which electrical load requirements and wind and solar resource data from the community was acquired to estimate savings in diesel fuel consumption for various renewable energy technologies. Wind was found to provide the most fuel displacement and was considered to be the most appropriate technology for these communities. A photovoltaic (PV) system of equivalent size would have significantly less impact on fuel savings in a community like Cambridge Bay, in part because a PV system would be poorly correlated on a seasonal basis with the energy requirements of the community. A wind-diesel system would be the most advantageous in terms of fuel savings due to its relatively high capacity factor, and due to the fact that is it is available year around. 4 refs., 1 tab., 4 figs

Electric vehicles and renewable energy in the transport sector - energy system consequences. Main focus: Battery electric vehicles and hydrogen based fuel cell vehicles

Energy Technology Data Exchange (ETDEWEB)

Nielsen, L.H.; Joergensen, K.

2000-04-01

The aim of the project is to analyse energy, environmental and economic aspects of integrating electric vehicles in the future Danish energy system. Consequences of large-scale utilisation of electric vehicles are analysed. The aim is furthermore to illustrate the potential synergistic interplay between the utilisation of electric vehicles and large-scale utilisation of fluctuating renewable energy resources, such as wind power. Economic aspects for electric vehicles interacting with a liberalised electricity market are analysed. The project focuses on battery electric vehicles and fuel cell vehicles based on hydrogen. Based on assumptions on the future technical development for battery electric vehicles, fuel cell vehicles on hydrogen, and for the conventional internal combustion engine vehicles, scenarios are set up to reflect expected options for the long-term development of road transport vehicles. Focus is put on the Danish fleet of passenger cars and delivery vans. The scenario analysis includes assumptions on market potential developments and market penetration for the alternative vehicles. Vehicle replacement rates in the Danish transport fleet and the size of fleet development are based on data from The Danish Road Directorate. The electricity supply system development assumed is based on the Danish energy plan, Energy 21, The Plan scenario. The time horizon of the analysis is year 2030. Results from the scenario analysis include the time scales involved for the potential transition towards electricity based vehicles, the fleet composition development, the associated developments in transport fuel consumption and fuel substitution, and the potential CO{sub 2}-emission reduction achievable in the overall transport and power supply system. Detailed model simulations, on an hourly basis, have furthermore been carried out for year 2005 that address potential electricity purchase options for electric vehicles in the context of a liberalised electricity market

Electric vehicles and renewable energy in the transport sector - energy system consequences. Main focus: Battery electric vehicles and hydrogen based fuel cell vehicles

International Nuclear Information System (INIS)

Nielsen, L.H.; Joergensen, K.

2000-04-01

The aim of the project is to analyse energy, environmental and economic aspects of integrating electric vehicles in the future Danish energy system. Consequences of large-scale utilisation of electric vehicles are analysed. The aim is furthermore to illustrate the potential synergistic interplay between the utilisation of electric vehicles and large-scale utilisation of fluctuating renewable energy resources, such as wind power. Economic aspects for electric vehicles interacting with a liberalised electricity market are analysed. The project focuses on battery electric vehicles and fuel cell vehicles based on hydrogen. Based on assumptions on the future technical development for battery electric vehicles, fuel cell vehicles on hydrogen, and for the conventional internal combustion engine vehicles, scenarios are set up to reflect expected options for the long-term development of road transport vehicles. Focus is put on the Danish fleet of passenger cars and delivery vans. The scenario analysis includes assumptions on market potential developments and market penetration for the alternative vehicles. Vehicle replacement rates in the Danish transport fleet and the size of fleet development are based on data from The Danish Road Directorate. The electricity supply system development assumed is based on the Danish energy plan, Energy 21, The Plan scenario. The time horizon of the analysis is year 2030. Results from the scenario analysis include the time scales involved for the potential transition towards electricity based vehicles, the fleet composition development, the associated developments in transport fuel consumption and fuel substitution, and the potential CO 2 -emission reduction achievable in the overall transport and power supply system. Detailed model simulations, on an hourly basis, have furthermore been carried out for year 2005 that address potential electricity purchase options for electric vehicles in the context of a liberalised electricity market. The

40 CFR 80.1416 - Petition process for evaluation of new renewable fuels pathways.

Science.gov (United States)

2010-07-01

... renewable fuels pathways. 80.1416 Section 80.1416 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Petition process for evaluation of new renewable fuels pathways. (a) Pursuant to this section, a party may... fuel pathway has not been evaluated by EPA to determine if it qualifies for a D code pursuant to § 80...

A parametric analysis of future ethanol use in the light-duty transportation sector: Can the US meet its Renewable Fuel Standard goals without an enforcement mechanism?

International Nuclear Information System (INIS)

Westbrook, Jessica; Barter, Garrett E.; Manley, Dawn K.; West, Todd H.

2014-01-01

The modified Renewable Fuel Standard (RFS2) prescribes a volume of biofuels to be used in the United States transportation sector each year through 2022. As the dominant component of the transportation sector, we consider the feasibility of the light-duty vehicle (LDV) parc to provide enough demand for biofuels to satisfy RFS2. Sensitivity studies show that the fuel price differential between gasoline and ethanol blendstocks, such as E85, is the principal factor in LDV biofuel consumption. The numbers of flex fuel vehicles and biofuel refueling stations will grow given a favorable price differential. However, unless the feedstock price differential becomes extreme (biomass prices below $100 per dry ton and oil prices above $215 per barrel), which deviates from historical price trends, LDV parc biofuel consumption will fall short of the RFS2 mandate without an enforcement mechanism. Additionally, such commodity prices might increase biofuel consumption in the short-term, but discourage use of biofuels in the long-term as other technologies that do not rely on any gasoline blendstock may be preferable. Finally, the RFS2 program goals of reducing fossil fuel consumption and transportation greenhouse gas emissions could be achieved through other pathways, such as notable improvements in conventional vehicle efficiency. - Author-Highlights: • At current commodity prices, the LDV fleet will not use enough biofuel to meet RFS2. • RFS2 can be met through the promotion of flex-fuel vehicles and their use of E85 fuel. • The gasoline-E85 price premium is the key factor in encouraging biofuel consumption. • RFS2 is satisfied at extreme oil prices (at least $215/barrel). • This oil price encourages biofuel use in the RFS2 timeframe, but not in the long run

Effects of Fuel Quantity on Soot Formation Process for Biomass-Based Renewable Diesel Fuel Combustion

KAUST Repository

Jing, Wei; Wu, Zengyang; Roberts, William L.; Fang, Tiegang

2016-01-01

Soot formation process was investigated for biomass-based renewable diesel fuel, such as biomass to liquid (BTL), and conventional diesel combustion under varied fuel quantities injected into a constant volume combustion chamber. Soot measurement

Electricity as Transportation ``Fuel''

Science.gov (United States)

Tamor, Michael

2013-04-01

The personal automobile is a surprisingly efficient device, but its place in a sustainable transportation future hinges on its ability use a sustainable fuel. While electricity is widely expected to be such a ``fuel,'' the viability of electric vehicles rests on the validity of three assumptions. First, that the emissions from generation will be significantly lower than those from competing chemical fuels whether `renewable' or fossil. Second, that advances in battery technology will deliver adequate range and durability at an affordable cost. Third, that most customers will accept any functional limitations intrinsic to electrochemical energy storage. While the first two are subjects of active research and vigorous policy debate, the third is treated virtually as a given. Popular statements to the effect that ``because 70% of all daily travel is accomplished in less than 100 miles, mass deployment of 100 mile EVs will electrify 70% of all travel'' are based on collections of one-day travel reports such as the National Household Travel Survey, and so effectively ignore the complexities of individual needs. We have analyzed the day-to-day variations of individual vehicle usage in multiple regions and draw very different conclusions. Most significant is that limited EV range results in a level of inconvenience that is likely to be unacceptable to the vast majority of vehicle owners, and for those who would accept that inconvenience, battery costs must be absurdly low to achieve any economic payback. In contrast, the plug-in hybrid (PHEV) does not suffer range limitations and delivers economic payback for most users at realistic battery costs. More importantly, these findings appear to be universal in developed nations, with labor market population density being a powerful predictor of personal vehicle usage. This ``scalable city'' hypothesis may prove to a powerful predictor of the evolution of transportation in the large cities of the developing world.

Renewable Energy Policy Fact sheet - Romania

International Nuclear Information System (INIS)

2017-07-01

The EurObserv'ER policy profiles give a snapshot of the renewable energy policy in the EU Member States. The promotion of renewable electricity in Romania relies primarily on a renewable quota scheme. Since 2017 the scheme has been closed for new projects. Renewable heating and cooling is promoted through investment subsidies. Renewable energy sources in the transport sector are promoted by a bio-fuels quota scheme and indirectly through a subsidy scheme for the purchase of electric vehicles

An evaluation of the policy and techno-economic factors affecting the potential for biogas upgrading for transport fuel use in the UK

International Nuclear Information System (INIS)

Patterson, Tim; Esteves, Sandra; Dinsdale, Richard; Guwy, Alan

2011-01-01

Gaseous biofuels including biomethane, which has been shown to be more environmentally beneficial than liquid biofuels, should contribute to meeting the challenging UK targets set for the supplying of biofuels to the road transport fuel market. Under the Renewable Transport Fuel Obligations the financial incentives for the supply of biofuels have been volatile, e.g. 2008/2009 saw Renewable Transport Fuel Certificate values fall to zero. Any shortfall from the maximum value has significant implications for all biofuels. It is demonstrated that biomethane can be produced at a cost which is competitive with liquid biofuels and fossil fuels within the UK. Technologies such as water scrubbing, pressure swing adsorption and physical and chemical absorption are available to upgrade biogas generated by anaerobic digestion of organic wastes to transport fuel quality, and technologies such as membrane separation and cryogenic distillation are being modified for such an application. The manufacture and sale of biomethane as a transport fuel is also financially competitive with Combined Heat and Power. One limiting factor may be the additional cost of purchasing and maintaining biomethane fuelled vehicles. Support in this area could lead to the rapid expansion of biomethane transport fuel infrastructure and bring significant long term environmental and economic advantages. - Research highlights: → A technical summary of commercially available biogas upgrading technologies is made. → An assessment of energetic, environmental and economic performance is included. → Proposed financial subsidies for biomethane transport fuel are investigated. → Biomethane can be financially competitive with liquid biofuels. → The enhanced environmental performance of biomethane should be reflected by the level of subsidy.

Outlook on renewable fuels in Sweden - Update and extension of the study 'Opportunities for renewable fuels in Sweden to 2030' by Grahn and Hansson, 2010; Utsikt foer foernybara drivmedel i Sverige - Uppdatering och utvidgning av studien 'Moejligheter foer foernybara drivmedel i Sverige till aar 2030', av Grahn och Hansson 2010

Energy Technology Data Exchange (ETDEWEB)

Hansson, Julia [IVL, Stockholm (Sweden); Grahn, Maria [Chalmers Tekniska Hoegskola, Goeteborg (Sweden)

2013-02-15

The purpose of this study is to update and extend the authors' analysis, from 2010. The report includes a compilation of other actors visions for the development of renewable fuels, a compilation of control means for renewable fuels, a survey of existing and planned production for biofuels in Sweden and outlook to the world. There is a discussion of Sweden's future import opportunities, a survey of the state of infrastructure and vehicles, and finally scenarios for the development of renewable fuels in Sweden to 2030, with different assumptions. The study's analysis is based on literature studies, contacts with actors in the field and on the results of our own scenarios. The scenarios provide a picture of the potential contribution of renewable fuels, to the Swedish road transport sector, can range from 7 to 16 TWh in 2020 and 13-30 TWh in 2030 (of which 5 to 13 TWh in 2020 and 13-26 TWh in 2030 is the possible domestic contribution that is., without imports)

78 FR 36041 - Regulation of Fuels and Fuel Additives: RFS Pathways II and Technical Amendments to the RFS 2...

Science.gov (United States)

2013-06-14

... Production, Transport and Tailpipe Emissions for Renewable Diesel and Naphtha C. Proposed Regulatory... and diesel fuel, or renewable fuels such as ethanol and biodiesel. Regulated categories and entities...

“Green” fuel tax on private transportation services and subsidies to electric energy. A model-based assessment for the main European countries

International Nuclear Information System (INIS)

Bartocci, Anna; Pisani, Massimiliano

2013-01-01

This paper evaluates the environmental and macroeconomic implications for France, Germany, Italy and Spain of taxing motor vehicle fuels for private transportation, a sector not subject to the Emissions Trading System, so as to reduce taxes on electricity consumption and increase subsidies to renewable sources of electricity generation. The assessment is based on a dynamic general equilibrium model calibrated for each of the four countries. The results suggest that the measures posited will reduce carbon dioxide emissions in the transportation sector and favor the development of electricity generation from renewable sources, thus limiting the growth of emissions from electricity generation. The measures do not jeopardize economic activity. The results are robust whether implementation is unilateral in one country or simultaneous throughout the EU. - Highlights: • The European Union's Agenda 2020 calls for member countries to reduce greenhouse gas emissions and increase renewable energy. • We evaluate implications in the EU of taxing fuels for private transportation, reducing taxes on electricity and increase subsidies to renewable sources of electricity. • The assessment is based on a dynamic general equilibrium model. • The measures reduce emissions, in particular in the transportation sector, favor electricity generation from renewable sources and do not jeopardize economic activity

Solid Oxide Fuel Cells Operating on Alternative and Renewable Fuels

Energy Technology Data Exchange (ETDEWEB)

Wang, Xiaoxing; Quan, Wenying; Xiao, Jing; Peduzzi, Emanuela; Fujii, Mamoru; Sun, Funxia; Shalaby, Cigdem; Li, Yan; Xie, Chao; Ma, Xiaoliang; Johnson, David; Lee, Jeong; Fedkin, Mark; LaBarbera, Mark; Das, Debanjan; Thompson, David; Lvov, Serguei; Song, Chunshan

2014-09-30

This DOE project at the Pennsylvania State University (Penn State) initially involved Siemens Energy, Inc. to (1) develop new fuel processing approaches for using selected alternative and renewable fuels – anaerobic digester gas (ADG) and commercial diesel fuel (with 15 ppm sulfur) – in solid oxide fuel cell (SOFC) power generation systems; and (2) conduct integrated fuel processor – SOFC system tests to evaluate the performance of the fuel processors and overall systems. Siemens Energy Inc. was to provide SOFC system to Penn State for testing. The Siemens work was carried out at Siemens Energy Inc. in Pittsburgh, PA. The unexpected restructuring in Siemens organization, however, led to the elimination of the Siemens Stationary Fuel Cell Division within the company. Unfortunately, this led to the Siemens subcontract with Penn State ending on September 23rd, 2010. SOFC system was never delivered to Penn State. With the assistance of NETL project manager, the Penn State team has since developed a collaborative research with Delphi as the new subcontractor and this work involved the testing of a stack of planar solid oxide fuel cells from Delphi.

Transport of MOX fuel

International Nuclear Information System (INIS)

Porter, I.R.; Carr, M.

1997-01-01

The regulatory framework which governs the transport of MOX fuel is set out, including packages, transport modes and security requirements. Technical requirements for the packages are reviewed and BNFL's experience in plutonium and MOX fuel transport is described. The safety of such operations and the public perception of safety are described and the question of gaining public acceptance for MOX fuel transport is addressed. The paper concludes by emphasising the need for proactive programmes to improve the public acceptance of these operations. (Author)

Renewable Energy Policy Fact sheet - Cyprus

International Nuclear Information System (INIS)

2017-07-01

The EurObserv'ER policy profiles give a snapshot of the renewable energy policy in the EU Member States. Electricity from renewable sources is promoted through investment subsidies in combination with a net metering scheme. Renewable heating and cooling is promoted by investment subsidies to enterprises and households respectively. To date, no incentives for production and use of bio-fuels in the transport sector are in place

Integrated transport and renewable energy systems

DEFF Research Database (Denmark)

Mathiesen, Brian Vad; Lund, Henrik; Nørgaard, P.

2008-01-01

No single technology can solve the problem of ever increasing CO2 emissions from transport. Here, a coherent effort to integrate transport into energyplanning is proposed, using multiple means promoting sustainable transport. It is concluded that a 100 per cent renewable energy transport system...... is possible but is connected to significant challenges in the path towards it. Biomass is a limited resource and it is important to avoid effecting the production of food. The integration of the transport with the energy system is crucial as is a multi-pronged strategy. Short term solutions have to consider...

Driving it home: choosing the right path for fueling North America's transportation future

Energy Technology Data Exchange (ETDEWEB)

Ann Bordetsky; Susan Casey-Lefkowitz; Deron Lovaas; Elizabeth Martin-Perera; Melanie Nakagawa; Bob Randall; Dan Woynillowicz

2007-06-15

North America faces an energy crossroads. With the world fast approaching the end of cheap, plentiful conventional oil, we must choose between developing ever-dirtier sources of fossil fuels -- at great cost to our health and environment -- or setting a course for a more sustainable energy future of clean, renewable fuels. This report explores the full scale of the damage done by attempts to extract oil from liquid coal, oil shale, and tar sands; examines the risks for investors of gambling on these dirty fuel sources; and lays out solutions for guiding us toward a cleaner fuel future. Table of contents: Executive Summary; Chapter 1: Transportation Fuel at a Crossroads; Chapter 2: Canadian Tar Sands: Scraping the Bottom of the Barrel in Endangered Forests; Chapter 3: Oil Shale Extraction: Drilling Through the American West; Chapter 4: Liquid Coal: A 'Clean Fuel' Mirage; Chapter 5: The Investment Landscape: Dirty Fuels Are Risky Business; Chapter 6: The Clean Path for Transportation and Conclusion.

Transportation of spent nuclear fuels

International Nuclear Information System (INIS)

Meguro, Toshiichi

1976-01-01

The spent nuclear fuel taken out of reactors is cooled in the cooling pool in each power station for a definite time, then transported to a reprocessing plant. At present, there is no reprocessing plant in Japan, therefore the spent nuclear fuel is shipped abroad. In this paper, the experiences and the present situation in Japan are described on the transport of the spent nuclear fuel from light water reactors, centering around the works in Tsuruga Power Station, Japan Atomic Power Co. The spent nuclear fuel in Tsuruga Power Station was first transported in Apr. 1973, and since then, about 36 tons were shipped to Britain by 5 times of transport. The reprocessing plant in Japan is expected to start operation in Apr. 1977, accordingly the spent nuclear fuel used for the trial will be transported in Japan in the latter half of this year. Among the permission and approval required for the transport of spent nuclear fuel, the acquisition of the certificate for transport casks and the approval of land and sea transports are main tasks. The relevant laws are the law concerning the regulations of nuclear raw material, nuclear fuel and reactors and the law concerning the safety of ships. The casks used in Tsuruga Power Station and EXL III type, and the charging of spent nuclear fuel, the decontamination of the casks, the leak test, land transport with a self-running vehicle, loading on board an exclusive carrier and sea transport are briefly explained. The casks and the ship for domestic transport are being prepared. (Kato, I.)

Peat classified as slowly renewable biomass fuel

International Nuclear Information System (INIS)

2001-01-01

thousands of years. The report states also that peat should be classified as biomass fuel instead of biofuels, such as wood, or fossil fuels such as coal. According to the report peat is a renewable biomass fuel like biofuels, but due to slow accumulation it should be considered as slowly renewable fuel. The report estimates that bonding of carbon in both virgin and forest drained peatlands are so high that it can compensate the emissions formed in combustion of energy peat

Fuels processing for transportation fuel cell systems

Science.gov (United States)

Kumar, R.; Ahmed, S.

Fuel cells primarily use hydrogen as the fuel. This hydrogen must be produced from other fuels such as natural gas or methanol. The fuel processor requirements are affected by the fuel to be converted, the type of fuel cell to be supplied, and the fuel cell application. The conventional fuel processing technology has been reexamined to determine how it must be adapted for use in demanding applications such as transportation. The two major fuel conversion processes are steam reforming and partial oxidation reforming. The former is established practice for stationary applications; the latter offers certain advantages for mobile systems and is presently in various stages of development. This paper discusses these fuel processing technologies and the more recent developments for fuel cell systems used in transportation. The need for new materials in fuels processing, particularly in the area of reforming catalysis and hydrogen purification, is discussed.

Ovonic Renewable Hydrogen (ORH) - low temperature hydrogen production from renewable fuels

International Nuclear Information System (INIS)

Reichman, B.; Mays, W.; Strebe, J.; Fetcenko, M.

2009-01-01

'Full text': ECD has developed a new technology to produce hydrogen from various organic matters. In this technology termed Ovonic Renewable Hydrogen (ORH), base material such as NaOH is used as a reactant to facilitate the reforming of the organic matters to hydrogen gas. This Base-Facilitated Reforming (BFR) process is a one-step process and has number of advantages over the conventional steam reforming and gasification processes including lower operation temperature and lower heat consumption. This paper will describe the ORH process and discuss its technological and economics advantages over the conventional hydrogen production processes. ORH process has been studied and demonstrated on variety of renewable fuels including liquid biofuels and solid biomass materials. Results of these studies will be presented. (author)

Photoactivated Fuel Cells (PhotoFuelCells. An alternative source of renewable energy with environmental benefits

Directory of Open Access Journals (Sweden)

Stavroula Sfaelou

2016-03-01

Full Text Available This work is a short review of Photoactivated Fuel Cells, that is, photoelectrochemical cells which consume an organic or inorganic fuel to produce renewable electricity or hydrogen. The work presents the basic features of photoactivated fuel cells, their modes of operation, the materials, which are frequently used for their construction and some ideas of cell design both for electricity and solar hydrogen production. Water splitting is treated as a special case of photoactivated fuel cell operation.

Transportation of nuclear fuel

International Nuclear Information System (INIS)

Prowse, D.R.

1979-01-01

Shipment of used fuel from nuclear reactors to a central fuel management facility is discussed with particular emphasis on the assessment of the risk to the public due to these shipments. The methods of transporting used fuel in large shipping containers is reviewed. In terms of an accident scenario, it is demonstrated that the primary risk of transport of used fuel is due to injury and death in common road accidents. The radiological nature of the used fuel cargo is, for all practical purposes, an insignificant factor in the total risk to the public. (author)

Renewable Energy Policy Fact sheet - Lithuania

International Nuclear Information System (INIS)

2017-09-01

The EurObserv'ER policy profiles give a snapshot of the renewable energy policy in the EU Member States. The main support scheme to stimulate electricity from renewable energy sources is a feed-in premium scheme. RES-E project developers with installations = 10 kW have to acquire access to this scheme by submitting successful bids in tenders. Subsidies and loans can be obtained by RES-E project developers through successful applications at the Climate Change Special Programme or the Lithuanian Environmental Investment Funds (investment subsidies only). RES-E plants are exempted from excise duty. Consumers with a small PV installation can benefit from net metering. Producers of heating and cooling from renewable energy sources are exempt from environmental pollution tax and are eligible for grants. Moreover, heat suppliers are obliged to purchase all heat produced from renewable energy sources. Renewable transport fuels are promoted through reimbursement of raw materials for bio-fuel production, a bio-fuels (blending) quota scheme as well as exemption from excise tax and environmental pollution tax

Model documentation renewable fuels module of the National Energy Modeling System

Science.gov (United States)

1995-06-01

This report documents the objectives, analytical approach, and design of the National Energy Modeling System (NEMS) Renewable Fuels Module (RFM) as it relates to the production of the 1995 Annual Energy Outlook (AEO95) forecasts. The report catalogs and describes modeling assumptions, computational methodologies, data inputs, and parameter estimation techniques. A number of offline analyses used in lieu of RFM modeling components are also described. The RFM consists of six analytical submodules that represent each of the major renewable energy resources -- wood, municipal solid waste (MSW), solar energy, wind energy, geothermal energy, and alcohol fuels. The RFM also reads in hydroelectric facility capacities and capacity factors from a data file for use by the NEMS Electricity Market Module (EMM). The purpose of the RFM is to define the technological, cost, and resource size characteristics of renewable energy technologies. These characteristics are used to compute a levelized cost to be competed against other similarly derived costs from other energy sources and technologies. The competition of these energy sources over the NEMS time horizon determines the market penetration of these renewable energy technologies. The characteristics include available energy capacity, capital costs, fixed operating costs, variable operating costs, capacity factor, heat rate, construction lead time, and fuel product price.

Model documentation renewable fuels module of the National Energy Modeling System

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-06-01

This report documents the objectives, analytical approach, and design of the National Energy Modeling System (NEMS) Renewable Fuels Module (RFM) as it relates to the production of the 1995 Annual Energy Outlook (AEO95) forecasts. The report catalogues and describes modeling assumptions, computational methodologies, data inputs, and parameter estimation techniques. A number of offline analyses used in lieu of RFM modeling components are also described. The RFM consists of six analytical submodules that represent each of the major renewable energy resources--wood, municipal solid waste (MSW), solar energy, wind energy, geothermal energy, and alcohol fuels. The RFM also reads in hydroelectric facility capacities and capacity factors from a data file for use by the NEMS Electricity Market Module (EMM). The purpose of the RFM is to define the technological, cost and resource size characteristics of renewable energy technologies. These characteristics are used to compute a levelized cost to be competed against other similarly derived costs from other energy sources and technologies. The competition of these energy sources over the NEMS time horizon determines the market penetration of these renewable energy technologies. The characteristics include available energy capacity, capital costs, fixed operating costs, variable operating costs, capacity factor, heat rate, construction lead time, and fuel product price.

On the road to fossil-free public transport: The case of Swedish bus fleets

International Nuclear Information System (INIS)

Xylia, Maria; Silveira, Semida

2017-01-01

Public transport is important for Sweden to acquire a fossil-fuel independent vehicle fleet by 2030. The aim of this paper is to assess the status of Swedish public bus fleets towards decarbonization, and explore factors affecting regional performance variations and fuel choices. Environmental performance indicators such as renewable fuel shares, CO 2 emissions, and energy efficiency are analyzed nationally and regionally. Fuel preferences and best practices are investigated through a survey and interviews with experts working with strategic planning at Public Transport Authorities. Almost 60% of the bus transport volume ran on renewables in 2014 compared to 8% in 2007, but regional variations are significant, partly due to factors such as driving conditions, bus and fuel types, typical trip lengths, and climatic conditions. However, there is no strong correlation between population densities or bus transport volume and the share of renewables achieved. This places political will, strategic planning and policies to promote public transport as key factors affecting renewable fuel deployment. Environmental factors are a priority when choosing fuels, while barriers to renewable fuels are mainly economic and political. Meanwhile, despite the overall progress, achievements in energy efficiency improvement are falling short in comparison to emissions reduction and adoption of renewable fuels, thus requiring further attention. - Highlights: • The penetration of renewables in Swedish public bus fleets reached ca. 60% in 2014. • Public bus emissions per vehicle-km have decreased by 43% between 2007 and 2014. • Efforts are needed to improve energy efficiency in bus transport. • Electricity is likely to receive increased attention according to expert survey.

GREET 1.5 - transportation fuel-cycle model - Vol. 1 : methodology, development, use, and results

International Nuclear Information System (INIS)

Wang, M. Q.

1999-01-01

This report documents the development and use of the most recent version (Version 1.5) of the Greenhouse Gases, Regulated Emissions, and Energy Use in Transportation (GREET) model. The model, developed in a spreadsheet format, estimates the full fuel-cycle emissions and energy associated with various transportation fuels and advanced vehicle technologies for light-duty vehicles. The model calculates fuel-cycle emissions of five criteria pollutants (volatile organic compounds, carbon monoxide, nitrogen oxides, particulate matter with diameters of 10 micrometers or less, and sulfur oxides) and three greenhouse gases (carbon dioxide, methane, and nitrous oxide). The model also calculates total energy consumption, fossil fuel consumption, and petroleum consumption when various transportation fuels are used. The GREET model includes the following cycles: petroleum to conventional gasoline, reformulated gasoline, conventional diesel, reformulated diesel, liquefied petroleum gas, and electricity via residual oil; natural gas to compressed natural gas, liquefied natural gas, liquefied petroleum gas, methanol, Fischer-Tropsch diesel, dimethyl ether, hydrogen, and electricity; coal to electricity; uranium to electricity; renewable energy (hydropower, solar energy, and wind) to electricity; corn, woody biomass, and herbaceous biomass to ethanol; soybeans to biodiesel; flared gas to methanol, dimethyl ether, and Fischer-Tropsch diesel; and landfill gases to methanol. This report also presents the results of the analysis of fuel-cycle energy use and emissions associated with alternative transportation fuels and advanced vehicle technologies to be applied to passenger cars and light-duty trucks

Hydrogen: Fueling the Future

International Nuclear Information System (INIS)

Leisch, Jennifer

2007-01-01

As our dependence on foreign oil increases and concerns about global climate change rise, the need to develop sustainable energy technologies is becoming increasingly significant. Worldwide energy consumption is expected to double by the year 2050, as will carbon emissions along with it. This increase in emissions is a product of an ever-increasing demand for energy, and a corresponding rise in the combustion of carbon containing fossil fuels such as coal, petroleum, and natural gas. Undisputable scientific evidence indicates significant changes in the global climate have occurred in recent years. Impacts of climate change and the resulting atmospheric warming are extensive, and know no political or geographic boundaries. These far-reaching effects will be manifested as environmental, economic, socioeconomic, and geopolitical issues. Offsetting the projected increase in fossil energy use with renewable energy production will require large increases in renewable energy systems, as well as the ability to store and transport clean domestic fuels. Storage and transport of electricity generated from intermittent resources such as wind and solar is central to the widespread use of renewable energy technologies. Hydrogen created from water electrolysis is an option for energy storage and transport, and represents a pollution-free source of fuel when generated using renewable electricity. The conversion of chemical to electrical energy using fuel cells provides a high efficiency, carbon-free power source. Hydrogen serves to blur the line between stationary and mobile power applications, as it can be used as both a transportation fuel and for stationary electricity generation, with the possibility of a distributed generation energy infrastructure. Hydrogen and fuel cell technologies will be presented as possible pollution-free solutions to present and future energy concerns. Recent hydrogen-related research at SLAC in hydrogen production, fuel cell catalysis, and hydrogen

Development of Nuclear Renewable Oil Shale Systems for Flexible Electricity and Reduced Fossil Fuel Emissions

Energy Technology Data Exchange (ETDEWEB)

Daniel Curtis; Charles Forsberg; Humberto Garcia

2015-05-01

We propose the development of Nuclear Renewable Oil Shale Systems (NROSS) in northern Europe, China, and the western United States to provide large supplies of flexible, dispatchable, very-low-carbon electricity and fossil fuel production with reduced CO2 emissions. NROSS are a class of large hybrid energy systems in which base-load nuclear reactors provide the primary energy used to produce shale oil from kerogen deposits and simultaneously provide flexible, dispatchable, very-low-carbon electricity to the grid. Kerogen is solid organic matter trapped in sedimentary shale, and large reserves of this resource, called oil shale, are found in northern Europe, China, and the western United States. NROSS couples electricity generation and transportation fuel production in a single operation, reduces lifecycle carbon emissions from the fuel produced, improves revenue for the nuclear plant, and enables a major shift toward a very-low-carbon electricity grid. NROSS will require a significant development effort in the United States, where kerogen resources have never been developed on a large scale. In Europe, however, nuclear plants have been used for process heat delivery (district heating), and kerogen use is familiar in certain countries. Europe, China, and the United States all have the opportunity to use large scale NROSS development to enable major growth in renewable generation and either substantially reduce or eliminate their dependence on foreign fossil fuel supplies, accelerating their transitions to cleaner, more efficient, and more reliable energy systems.

Impacts of renewable fuel regulation and production on agriculture, energy, and welfare

Science.gov (United States)

McPhail, Lihong Lu

The purpose of this dissertation is to study the impact of U.S. federal renewable fuel regulations on energy and agriculture commodity markets and welfare. We consider two federal ethanol policies: the Renewable Fuel Standard (RFS) contained in the Energy Security and Independence Act of 2007 and tax credits to ethanol blenders contained in the Food, Conservation, and Energy Act of 2008. My first essay estimates the distribution of short-run impacts of changing federal ethanol policies on U.S. energy prices, agricultural commodity prices, and welfare through a stochastic partial equilibrium model of U.S. corn, ethanol, and gasoline markets. My second essay focuses on studying the price behavior of the renewable fuel credit (RFC) market, which is the mechanism developed by the Environmental Protection Agency (EPA) to meet the RFS. RFCs are a tradable, bankable, and borrowable accounting mechanism to ensure that all obligated parties use a mandated level of renewable fuel. I first develop a conceptual framework to understand how the market works and then apply stochastic dynamic programming to simulate prices for RFCs, examine the sensitivity of prices to relevant shocks, and estimate RFC option premiums. My third essay assesses the impact of policy led U.S. ethanol on the markets of global crude oil and U.S. gasoline using a structural Vector Auto Regression model of global crude oil, U.S. gasoline and ethanol markets.

Renewable Energy Policy Fact sheet - Greece

International Nuclear Information System (INIS)

2017-07-01

The EurObserv'ER policy profiles give a snapshot of the renewable energy policy in the EU Member States. In Greece, electricity from renewable sources is promoted through feed-in premiums, granted through tenders (as from 2017), feed-in tariffs for limited cases, a preferential tax regime (since 2016) and a net metering scheme. Heating and cooling from renewable energy sources is incentivised by way of a preferential tax regime and an investment subsidy scheme. The main instrument for renewable energy use in transport is a bio-fuels quota scheme

Fuel cells and electrolysers in future energy systems

DEFF Research Database (Denmark)

Mathiesen, Brian Vad

be considered which fuels such technologies can utilise and how these fuels can be distributed. Natural gas is not an option in future renewable energy systems and the de‐ mand for gaseous fuels, such as biogas or syngas, will increase significantly. Hence, fuel cell CHP plants represent a more fuel...... of transport, battery electric vehicles are more suitable than hydrogen fuel cell vehicles in future energy system. Battery electric ve‐ hicles may, for a part of the transport demand, have limitations in their range. Hybrid tech‐ nologies may provide a good option, which can combine the high fuel efficiency......Efficient fuel cells and electrolysers are still at the development stage. In this dissertation, future developed fuel cells and electrolysers are analysed in future renewable energy sys‐ tems. Today, most electricity, heat and transport demands are met by combustion tech‐ nologies. Compared...

Probability of spent fuel transportation accidents

International Nuclear Information System (INIS)

McClure, J.D.

1981-07-01

The transported volume of spent fuel, incident/accident experience and accident environment probabilities were reviewed in order to provide an estimate of spent fuel accident probabilities. In particular, the accident review assessed the accident experience for large casks of the type that could transport spent (irradiated) nuclear fuel. This review determined that since 1971, the beginning of official US Department of Transportation record keeping for accidents/incidents, there has been one spent fuel transportation accident. This information, coupled with estimated annual shipping volumes for spent fuel, indicated an estimated annual probability of a spent fuel transport accident of 5 x 10 -7 spent fuel accidents per mile. This is consistent with ordinary truck accident rates. A comparison of accident environments and regulatory test environments suggests that the probability of truck accidents exceeding regulatory test for impact is approximately 10 -9 /mile

European experience with spent fuel transport

International Nuclear Information System (INIS)

Hunter, I.A.

1995-01-01

Nuclear Transport Ltd has transported 5000 tonnes of spent fuel from 35 reactors in 8 European countries since 1972. Transport management is governed by the Quality Plan for: transport administration, packaging and shipment procedures at the shipping plant, operations at the power plant, and packaging and shipment organization at the power plant. Selection of a suitable carrier device is made with regard to the shipping plant requirements, physical limitations of the reactor, fuel characteristics, and transport route constraints. The transport plan is set up taking into account exploitation of the casks, reactor shut-down requirements, fuel acceptance plans at the reprocessing plant, and cask maintenance periods. A transport cycle involving spent fuel shipment to La Hague or to Sellafield takes typically two or four weeks, respectively. Most transports through Europe are by rail. A special-design railway ferry boat serves transports to the United Kingdom. Both wet or dry casks are employed. Modern casks are designed for high burnups and for oxide fuels. (J.B.)

75 FR 79964 - Regulation of Fuels and Fuel Additives: Modifications to Renewable Fuel Standard Program

Science.gov (United States)

2010-12-21

... renewable fuel facility to be considered biogas for purposes of Table 1 to Sec. 80.1426; --Sec. 80.1452(b... explained that many developers of ethanol facilities, including their own, sought to obtain construction permits without going through EPA's New Source Review (NSR) program, and were able to do so by obtaining...

Fuel cells for transportation program: FY1997 national laboratory annual report

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-12-31

The Department of Energy (DOE) Fuel Cells for Transportation Program is structured to effectively implement the research and development (R and D) required for highly efficient, low or zero emission fuel cell power systems to be a viable replacement for the internal combustion engine in automobiles. The Program is part of the Partnership for a New Generation of Vehicles (PNGV), a government-industry initiative aimed at development of an 80 mile-per-gallon vehicle. This Annual Report summarizes the technical accomplishments of the laboratories during 1997. Participants include: Argonne National Laboratory (ANL), Brookhaven National Laboratory (BNL), Lawrence Berkeley National Laboratory (LBNL), Los Alamos National Laboratory (LANL), Oak Ridge National Laboratory (ORNL), Pacific Northwest National Laboratory (PNNL), and the National Renewable Energy Laboratory (NREL). During 1997, the laboratory R and D included one project on solid oxide fuel cells; this project has since been terminated to focus Department resources on PEM fuel cells. The technical component of this report is divided into five key areas: fuel cell stack research and development; fuel processing; fuel cell modeling, testing, and evaluation; direct methanol PEM fuel cells; and solid oxide fuel cells.

Method of transporting fuel assemblies

International Nuclear Information System (INIS)

Okada, Katsutoshi.

1979-01-01

Purpose: To enable safety transportation of fuel assemblies for FBR type reactors by surrounding each of fuel elements in a wrapper tube by a rubbery, hollow cylindrical container and by sealing medium such as air to the inside of the container. Method: A fuel element is contained in a hollow cylindrical rubber-like tube. The fuel element has an upper end plug, a lower end plug and a wire spirally wound around the outer periphery. Upon transportation of the fuel assemblies, each of the fuel elements is covered with the container and arranged in the wrapper tube and then the fuel assemblies are assembled. Then, medium such as air is sealed for each of the fuel elements by way of an opening and then the opening is tightly closed. Before loading the transported fuel assemblies in the reactor, the medium is discharged through the opening and the container is completely extracted and removed from the inside of the wrapper tube. (Seki, T.)

Renewable energies - To put an end to common beliefs

International Nuclear Information System (INIS)

Claustre, Raphael; Jedliczka, Marc; Fink, Meike

2014-07-01

This publication explains why the following common beliefs are wrong: renewable energies are expensive; our energy bill will increase because of renewable energies; renewable energies do not create jobs; renewable energies deplete rare resources and biodiversity; renewable energies are not reliable; because of renewable energies, we'll have high voltage lines everywhere; agro-fuels are the only solution for transport; using wood for heating destroys the forest; there will never be enough renewable energies for heating; energy is the concern of large corporations; we are being ripped with renewable energies

77 FR 71474 - Commercial Space Transportation Advisory Committee-Charter Renewal

Science.gov (United States)

2012-11-30

... DEPARTMENT OF TRANSPORTATION Federal Aviation Administration Commercial Space Transportation... Transportation (DOT). ACTION: Announcement of Charter Renewal of the Commercial Space Transportation Advisory... Administrator of the Federal Aviation Administration (FAA) on the critical matters facing the U.S. commercial...

Renewables 2018 - Global status report. A comprehensive annual overview of the state of renewable energy. Advancing the global renewable energy transition - Highlights of the REN21 Renewables 2018 Global Status Report in perspective

International Nuclear Information System (INIS)

Sawin, Janet L.; Sverrisson, Freyr; Rutovitz, Jay; Dwyer, Scott; Teske, Sven; Murdock, Hannah E.; Adib, Rana; Guerra, Flavia; Murdock, Hannah E.; Blanning, Linh H.; Guerra, Flavia; Hamirwasia, Vibhushree; Misra, Archita; Satzinger, Katharina; Williamson, Laura E.; Lie, Mimi; Nilsson, Anna; Aberg, Emma; Weckend, Stephanie; Wuester, Henning; Ferroukhi, Rabia; Garcia, Celia; Khalid, Arslan; Renner, Michael; Taylor, Michael; Epp, Barbel; Seyboth, Kristin; Skeen, Jonathan; Kamiya, George; Munuera, Luis; Appavou, Fabiani; Brown, Adam; Kondev, Bozhil; Musolino, Evan; Brown, Adam; Mastny, Lisa; Arris, Lelani

2018-06-01

REN21's Renewables 2018 Global Status Report presents developments and trends through the end of 2017, as well as observed trends from early 2018 where available. Renewable power accounted for 70% of net additions to global power generating capacity in 2017, the largest increase in renewable power capacity in modern history, according to REN21's Renewables 2018 Global Status Report (GSR). But the heating, cooling and transport sectors - which together account for about four-fifths of global final energy demand - continue to lag far behind the power sector. The GSR, published today, is the most comprehensive annual overview of the state of renewable energy worldwide. New solar photovoltaic (PV) capacity reached record levels: Solar PV additions were up 29% relative to 2016, to 98 GW. More solar PV generating capacity was added to the electricity system than net capacity additions of coal, natural gas and nuclear power combined. Wind power also drove the uptake of renewables with 52 GW added globally. Investment in new renewable power capacity was more than twice that of net, new fossil fuel and nuclear power capacity combined, despite large, ongoing subsidies for fossil fuel generation. More than two-thirds of investments in power generation were in renewables in 2017, thanks to their increasing cost-competitiveness - and the share of renewables in the power sector is expected to only continue to rise. Investment in renewables was regionally concentrated: China, Europe and the United States accounted for nearly 75% of global investment in renewables in 2017. However, when measured per unit of gross domestic product (GDP), the Marshall Islands, Rwanda, the Solomon Islands, Guinea Bissau, and many other developing countries are investing as much as or more in renewables than developed and emerging economies. Both energy demand and energy-related CO 2 emissions rose substantially for the first time in four years. Energy-related CO 2 emissions rose by 1

75 FR 26049 - Regulation of Fuels and Fuel Additives: Modifications to Renewable Fuel Standard Program

Science.gov (United States)

2010-05-10

... comment period on this action. Any parties interested in commenting must do so at this time. For further... Technologies for Renewable Fuel Pathways The final RFS2 rule includes two corn ethanol pathways in Table 1 of... construction of the grandfathered facilities commenced would be contained in Sec. 80.1450(b)(vi), since Sec. 80...

MOX fuel transport: the French experience

International Nuclear Information System (INIS)

Sanchis, H.; Verdier, A.; Sanchis, H.

1999-01-01

In the back-end of the fuel cycle, several leading countries have chosen the Reprocessing, Conditioning, Recycling (RCR) option. Plutonium recycling in the form of MOX fuel is a mature industry, with successful operational experience and large-scale fabrication plants an several European countries. The COGEMA Group has developed the industrialized products to master the RCR operation including transport COGEMA subsidiary, TRANSNUCLEAIRE has been operating MOX fuel transports on an industrial scale for more than 10 years. In 1998, around 200 transports of Plutonium materials have been organised by TRANSNUCLEAIRE. These transports have been carried out by road between various facilities in Europe: reprocessing plants, manufacturing plants and power plants. The materials transported are either: PuO 2 and MOX powder; BWR and PWR MOX fuel rods; BWR and PWR MOX fuel assemblies. Because MOX fuel transport is subject to specific safety, security and fuel integrity requirements, the MOX fuel transport system implemented by TRANSNUCLEAIRE is fully dedicated. Packaging have been developed, licensed and manufactured for each kind of MOX material in compliance with relevant regulations. A fleet of vehicles qualified according to existing physical protection regulations is operated by TRANSNUCLEAIRE. TRANSNUCLEAIRE has gained a broad experience in MOX transport in 10 years. Technical and operational know-how has been developed and improved for each step: vehicles and packaging design and qualification; vehicle and packaging maintenance; transport operations. Further developments are underway to increase the payload of the packaging and to improve the transport conditions, safety and security remaining of course top priority. (authors)

Transport of irradiated nuclear fuel

International Nuclear Information System (INIS)

1980-01-01

In response to public interest in the transport by rail through London of containers of irradiated fuel elements on their way from nuclear power stations to Windscale, the Central Electricity Generating Board and British Rail held three information meetings in London in January 1980. One meeting was for representatives of London Borough Councils and Members of Parliament with a known interest in the subject, and the others were for press, radio and television journalists. This booklet contains the main points made by the principal speakers from the CEGB and BR. (The points covered include: brief description of the fuel cycle; effect of the fission process in producing plutonium and fission products in the fuel element; fuel transport; the fuel flasks; protection against accidents; experience of transporting fuel). (U.K.)

Towards sustainable urban transportation: Test, demonstration and development of fuel cell and hybrid-electric buses

International Nuclear Information System (INIS)

Folkesson, Anders

2008-05-01

Several aspects make today's transport system non-sustainable: - Production, transport and combustion of fossil fuels lead to global and local environmental problems. - Oil dependency in the transport sector may lead to economical and political instability. - Air pollution, noise, congestion and land-use may jeopardise public health and quality of life, especially in urban areas. In a sustainable urban transport system most trips are made with public transport because high convenience and comfort makes travelling with public transport attractive. In terms of emissions, including noise, the vehicles are environmentally sustainable, locally as well as globally. Vehicles are energy-efficient and the primary energy stems from renewable sources. Costs are reasonable for all involved, from passengers, bus operators and transport authorities to vehicle manufacturers. The system is thus commercially viable on its own merits. This thesis presents the results from three projects involving different concept buses, all with different powertrains. The first two projects included technical evaluations, including tests, of two different fuel cell buses. The third project focussed on development of a series hybrid-bus with internal combustion engine intended for production around 2010. The research on the fuel cell buses included evaluations of the energy efficiency improvement potential using energy mapping and vehicle simulations. Attitudes to hydrogen fuel cell buses among passengers, bus drivers and bus operators were investigated. Safety aspects of hydrogen as a vehicle fuel were analysed and the use of hydrogen compared to electrical energy storage were also investigated. One main conclusion is that a city bus should be considered as one energy system, because auxiliaries contribute largely to the energy use. Focussing only on the powertrain is not sufficient. The importance of mitigating losses far down an energy conversion chain is emphasised. The Scania hybrid fuel cell

Renewable Energy Policy Fact sheet - Portugal

International Nuclear Information System (INIS)

2017-07-01

The EurObserv'ER policy profiles give a snapshot of the renewable energy policy in the EU Member States. In Portugal, electricity from renewable sources from existing plants is mainly promoted through a feed-in tariff. Support to new RES plants can currently only be remunerated through the open energy market. For RES-H there is currently no direct support mechanism or fiscal benefit in place (as of January 2017); only indirect support. In the transport sector, the main incentives are a bio-fuel quota system and a tax exemption to small producers of bio-fuels

Liquid fuels from renewable resources in Canada: systems economics studies

National Research Council Canada - National Science Library

Osler, C. F

1978-01-01

This paper highlights the methodology and results of a six volume study completed for the Canadian government on alternatives for liquid fuel production from renewable resources after the mid-1980s...

Spent fuels transportation coming from Australia

International Nuclear Information System (INIS)

2002-01-01

Maritime transportation of spent fuels from Australia to France fits into the contract between COGEMA and ANSTO, signed in 1999. This document proposes nine information cards in this domain: HIFAR a key tool of the nuclear, scientific and technological australian program; a presentation of the ANSTO Australian Nuclear Science and Technology Organization; the HIFAR spent fuel management problem; the COGEMA expertise in favor of the research reactor spent fuel; the spent fuel reprocessing at La Hague; the transports management; the transport safety (2 cards); the regulatory framework of the transports. (A.L.B.)

Evaluating the use of renewable fuel sources to heat flue-cured tobacco barns

OpenAIRE

Brown, Robert T

2018-01-01

Evaluating the use of renewable fuel sources to heat flue-cured tobacco barns Robert Taylor Brown ABSTRACT The curing of flue-cured tobacco (Nicotiana tabacum L.) is an energy intensive process and represents a significant portion of the overall cost of production. Given the goal of the industry to reduce the environmental footprint of tobacco production and the energy demand of curing, attention has been directed to explore options for the use of renewable fuels for heating to...

Solid fuel applications to transportation engines

Energy Technology Data Exchange (ETDEWEB)

Rentz, Richard L.; Renner, Roy A.

1980-06-01

The utilization of solid fuels as alternatives to liquid fuels for future transportation engines is reviewed. Alternative liquid fuels will not be addressed nor will petroleum/solid fuel blends except for the case of diesel engines. With respect to diesel engines, coal/oil mixtures will be addressed because of the high interest in this specific application as a result of the large number of diesel engines currently in transportation use. Final assessments refer to solid fuels only for diesel engines. The technical assessments of solid fuels utilization for transportation engines is summarized: solid fuel combustion in transportation engines is in a non-developed state; highway transportation is not amenable to solid fuels utilization due to severe environmental, packaging, control, and disposal problems; diesel and open-cycle gas turbines do not appear worthy of further development, although coal/oil mixtures for slow speed diesels may offer some promise as a transition technology; closed-cycle gas turbines show some promise for solid fuels utilization for limited applications as does the Stirling engine for use of cleaner solid fuels; Rankine cycle engines show good potential for limited applications, such as for locomotives and ships; and any development program will require large resources and sophisticated equipment in order to advance the state-of-the-art.

Guidance on Biogas used to Produce CNG or LNG under the Renewable Fuel Standard Program

Science.gov (United States)

Provides EPA’s interpretation of biogas quality and RIN generation requirements that apply to renewable fuel production pathways involving the injection into a commercial pipeline of biogas for use in producing renewable CNG or renewable LNG.

The water footprint of biofuel-based transport

NARCIS (Netherlands)

Gerbens-Leenes, Winnie; Hoekstra, Arjen Ysbert

2011-01-01

The EU target to replace 10 percent of transport fuels by renewables by 2020 requires additional water. This study calculates water footprints (WFs) of transport modes using first generation bio-ethanol, biodiesel or bio-electricity and of European transport if 10 percent of transport fuels is

Alternatives to traditional transportation fuels: An overview

Energy Technology Data Exchange (ETDEWEB)

1994-06-01

This report presents the first compilation by the Energy Information Administration (EIA) of information on alternatives to gasoline and diesel fuel. The purpose of the report is: (1) to provide background information on alternative transportation fuels and replacement fuels compared with gasoline and diesel fuel, and (2) to furnish preliminary estimates of alternative transportation fuels and alternative fueled vehicles as required by the Energy Policy Act of 1992 (EPACT), Title V, Section 503, ``Replacement Fuel Demand Estimates and Supply Information.`` Specifically, Section 503 requires the EIA to report annually on: (1) the number and type of alternative fueled vehicles in existence the previous year and expected to be in use the following year, (2) the geographic distribution of these vehicles, (3) the amounts and types of replacement fuels consumed, and (4) the greenhouse gas emissions likely to result from replacement fuel use. Alternative fueled vehicles are defined in this report as motorized vehicles licensed for on-road use, which may consume alternative transportation fuels. (Alternative fueled vehicles may use either an alternative transportation fuel or a replacement fuel.) The intended audience for the first section of this report includes the Secretary of Energy, the Congress, Federal and State agencies, the automobile manufacturing industry, the transportation fuel manufacturing and distribution industries, and the general public. The second section is designed primarily for persons desiring a more technical explanation of and background for the issues surrounding alternative transportation fuels.

Three Essays on Renewable Energy Policy and its Effects on Fossil Fuel Generation in Electricity Markets

Science.gov (United States)

Bowen, Eric

In this dissertation, I investigate the effectiveness of renewable policies and consider their impact on electricity markets. The common thread of this research is to understand how renewable policy incentivizes renewable generation and how the increasing share of generation from renewables affects generation from fossil fuels. This type of research is crucial for understanding whether policies to promote renewables are meeting their stated goals and what the unintended effects might be. To this end, I use econometric methods to examine how electricity markets are responding to an influx of renewable energy. My dissertation is composed of three interrelated essays. In Chapter 1, I employ recent scholarship in spatial econometrics to assess the spatial dependence of Renewable Portfolio Standards (RPS), a prominent state-based renewable incentive. In Chapter 2, I explore the impact of the rapid rise in renewable generation on short-run generation from fossil fuels. And in Chapter 3, I assess the impact of renewable penetration on coal plant retirement decisions.

Fuel element transport container

International Nuclear Information System (INIS)

Benna, P.; Neuenfeldt, W.

1979-01-01

The reprocessing system includes a large number of waterfilled ponds next to each other for the intermediate storage of fuel elements from LWR's. The fuel element transport device is allocated to a middle pond. The individual ponds are separated from each other by walls, and are only accessible from the middle pond via narrow passages. The transport device includes a telescopic running rail for a trolley with a grab device for the fuel element. The running rail is supported in turn by a second trolley, which can be moved by wheels on rails. Part of the drive of the first trolley is arranged on the second one. Using this transport device, adjacent ponds can be served through the passage openings. (DG) [de

77 FR 1319 - Regulation of Fuels and Fuel Additives: 2012 Renewable Fuel Standards

Science.gov (United States)

2012-01-09

... fuels such as ethanol and biodiesel. Potentially regulated categories include: NAICS \\1\\ Examples of... they are produced as well as the cost associated with transporting these fuels to the U.S. Of the... II.E, we believe that the 1.0 billion gallon standard can indeed be met. Since biodiesel has an...

Integrated electrofuels and renewable energy systems

DEFF Research Database (Denmark)

Ridjan, Iva

energy into chemical energy by means of electrolysers, thus connecting fluctuating renewable energy to the vast amount of fuel storage already available in today’s energy systems. The conducted research indicates that electrofuels for heavy-duty transportation are technically and economically viable...... in energy systems and could play an important role in future energy systems. The cross-sector approach in the fuel production, by redirecting the excess electricity to the transport sector, is creating the flexibility and storage buffer for fluctuating electricity. The key concern in the short term should...

Transport Energy Impact Analysis; NREL (National Renewable Energy Laboratory)

Energy Technology Data Exchange (ETDEWEB)

Gonder, J.

2015-05-13

Presented at the Sustainable Transportation Energy Pathways Spring 2015 Symposium on May 13, 2015, this presentation by Jeff Gonder of the National Renewable Energy Laboratory (NREL) provides information about NREL's transportation energy impact analysis of connected and automated vehicles.

Transportation of irradiated fuel elements

International Nuclear Information System (INIS)

1980-01-01

A critique is presented of current methods of transporting spent nuclear fuel and the inadequacies of the associated contingency plans, with particular reference to the transportation of irradiated fuel through London. Anti-nuclear and pro-nuclear arguments are presented on a number of factors, including tests on flasks, levels of radiation exposure, routine transport arrangements and contingency arrangements. (U.K.)

NAPL migration and ecotoxicity of conventional and renewable fuels in accidental spill scenarios.

Science.gov (United States)

Malk, Vuokko; Barreto Tejera, Eduardo; Simpanen, Suvi; Dahl, Mari; Mäkelä, Riikka; Häkkinen, Jani; Kiiski, Anna; Penttinen, Olli-Pekka

2014-01-01

Fuels derived from non-petroleum renewable resources have raised interest due to their potential in replacing petroleum-based fuels, but information on their fate and effects in the terrestrial and aquatic environments in accidental spill scenario is limited. In this study, migration of four fuels (conventional diesel, conventional gasoline, renewable diesel NExBTL, and ethanol-blended gasoline RE85 containing maximum 85% ethanol) as non-aqueous phase liquids (NAPL) in soil was demonstrated in a laboratory-scale experiment. Ecotoxicity data was produced for the same fuels. There was no significant difference in migration of conventional and renewable diesel, but gasoline migrated 1.5 times deeper and 7-9 times faster in sand than diesel. RE85 spread horizontally wider but not as deep (p gasoline. Conventional gasoline was the most toxic (lethal concentration [LC50] 20 mg/kg total hydrocarbon content [THC]) among the studied fuels in soil toxicity test with earthworm Eisenia fetida followed by ethanol-blended gasoline (LC50 1,643 mg/kg THC) and conventional diesel (LC50 2,432 mg/kg THC), although gasoline evaporated fast from soil. For comparison, the toxicity of the water-accommodated fractions (WAF) of the fuels was tested with water flea Daphnia magna and Vibrio fischeri, also demonstrating groundwater toxicity. The WAF of conventional gasoline and RE85 showed almost similar toxicity to both the aquatic test species. EC50 values of 1:10 (by volume) WAF were 9.9 %WAF (gasoline) and 9.3 %WAF (RE85) to D. magna and 9.3 %WAF (gasoline) and 12.3 %WAF (RE85) to V. fischeri. Low solubility decreased toxicity potential of conventional diesel in aquatic environment, but direct physical effects of oil phase pose a threat to organisms in nature. Renewable diesel NExBTL did not show clear toxicity to any test species.

Renewable Energy Policy Fact sheet - Estonia

International Nuclear Information System (INIS)

2017-09-01

The EurObserv'ER policy profiles give a snapshot of the renewable energy policy in the EU Member States. Electricity from renewable sources is mainly promoted through feed-in premiums (FiP). In addition, investment subsidies are available for biogas/biomass-based RES-E and wind power installations. Renewable heat is stimulated through investment subsidies to CHP plants generating renewable heat and electricity, as well as subsidies for private heat consumers. Renewable transport fuels are currently mainly incentivised by way of a support scheme to promote the purchase of electric cars that use power produced from renewable energy sources. Recently, a measure for supporting bio-methane in the transport sector has been adopted. Generally, a number of investment subsidy schemes are in place to promote the development, installation and use of renewable energy production installations. However, certain subsidy conditions still have to be announced and implemented. The total amount of financial support to be allocated to renewable energy and energy efficiency related projects during period 2014-2020 will be over euro 490 million. The current administratively determined FiP scheme is set to be replaced by an auction-based scheme within short

Renewable Energy Policy Fact sheet - Poland

International Nuclear Information System (INIS)

2017-09-01

The EurObserv'ER policy profiles give a snapshot of the renewable energy policy in the EU Member States. Mid-2016 Poland revamped its national support scheme for electricity from renewable energy sources, started to phase out a certificates-backed renewable electricity quota scheme, and put in place a feed-in tariff/feed-in premium (FiT/FiP) system in place with the support levels being determined by approved tender bids. Furthermore, a fiscal and soft loan instrument is used for supplementary support. Three subsidy instruments and a soft loan instrument are deployed for the promotion of renewable heat. Renewable energy in transport is promoted through a bio-fuels quota scheme

Alternatives to traditional transportation fuels 1993

Energy Technology Data Exchange (ETDEWEB)

1995-01-01

In recent years, gasoline and diesel fuel have accounted for about 80 percent of total transportation fuel and nearly all of the fuel used in on-road vehicles. Growing concerns about the environmental effects of fossil fuel use and the Nation`s high level of dependence on foreign oil are providing impetus for the development of replacements or alternatives for these traditional transportation fuels. (The Energy Policy Act of 1992 definitions of {open_quotes}replacement{close_quotes} and {open_quotes}alternative{close_quotes} fuels are presented in the following box.) The Alternative Motor Fuels Act of 1988, the Clean Air Act Amendments of 1990 (CAAA90) and the Energy Policy Act of 1992 (EPACT) are significant legislative forces behind the growth of replacement fuel use. Alternatives to Traditional Transportation Fuels 1993 provides the number of on-road alternative fueled vehicles in use in the United States, alternative and replacement fuel consumption, and information on greenhouse gas emissions resulting from the production, delivery, and use of replacement fuels for 1992, 1993, and 1995.

Spent fuel transportation problems

International Nuclear Information System (INIS)

Kondrat'ev, A.N.; Kosarev, Yu.A.; Yulikov, E.A.

1977-01-01

In this paper, problems of transportation of nuclear spent fuel to reprocessing plants are discussed. The solutions proposed are directed toward the achievement of the transportation as economic and safe as possible. The increase of the nuclear power plants number in the USSR and the great distances between these plants and the reprocessing plants involve an intensification of the spent fuel transportation. Higher burnup and holdup time reduction cause the necessity of more bulky casks. In this connection, the economic problems become still more important. One of the ways of the problem solution is the development of rational and cheap cask designs. Also, the enforcement in the world of the environmental and personnel health protection requires to increase the transportation reliability and safety. The paper summarizes safe transportation rules with clarifying the following questions: the increase of the transport unit quantity of the spent fuel; rational shipment organization that minimizes vehicle turnover cycle duration; development of the reliable calculation methods to determine strength, thermal conditions and nuclear safety of transport packaging as applied to the vehicles of high capacity; maximum unification of vehicles, calculation methods and documents; and cask testing on models and in pilot scale on specific test rigs to assure that they meet the international safe fuel shipment rules. Besides, some considerations on the choice and use of structural materials for casks are given, and problems of manufacturing such casks from uranium and lead are considered, as well as problems of the development of fireproof shells, control instrumentation, vehicles decontamination, etc. All the problems are considered from the point of view of normal and accidental shipment conditions. Conclusions are presented [ru

Fuel characterisation, engine performance, combustion and exhaust emissions with a new renewable Licella biofuel

International Nuclear Information System (INIS)

Nabi, Md Nurun; Rahman, Md Mostafizur; Islam, Muhammad Aminul; Hossain, Farhad M.; Brooks, Peter; Rowlands, William N.; Tulloch, John; Ristovski, Zoran D.; Brown, Richard J.

2015-01-01

Highlights: • A new biofuel produced by hydrothermal liquefaction is investigated. • Licella biofuel blends showed no significant changes in engine performance. • Licella blends showed higher THC and NO emissions. • PM and PN emissions were observed to be lower for all Licella blends. • Hydrothermal liquefaction Licella biofuel is suitable for use in diesel engine. - Abstract: The current study investigates the opportunity of using Licella biofuel as a partly renewable fuel provided by Licella P/L. Hereafter this fuel will be referred to as Licella biofuel. The renewable component of the Licella biofuel was made from the hydrothermal conversion of Australian pinus radiata wood flour using Licella’s proprietary Cat-HTR™ technology. The diesel-soluble component of the hydrothermal product was extracted into road diesel to give a blended fuel containing approximately 30% renewable material with the balance from diesel. This was further blended with a regular diesel fuel (designated R0) to give fuels for testing containing 5%, 10% and 20% renewable fuel (designated R5, R10 and R20). Some of the key fuel properties were measured for R30 and compared with those of regular diesel fuel. The engine experiment was conducted on a four-cylinder turbocharged common rail direct injection diesel engine. All experiments were performed with a constant speed and five different engine loads. Exhaust emissions including particulate matter (PM) mass and numbers, nitric oxide (NO), total unburnt hydrocarbon (THC), carbon dioxide (CO 2 ) and performance parameters including brake power (BP), indicated power (IP), brake mean effective pressure (BMEP), indicated mean effective pressure (IMEP), mechanical efficiency (ME), brake thermal efficiency (BTE) and brake specific energy consumption (BSEC) were investigated for all four blends (R0, R5, R10 and R20). Among other engine parameters, in-cylinder pressure, heat release rate (HRR) and pressure (P) versus volume (V) diagrams

From waste to traffic fuel (W-fuel)

Energy Technology Data Exchange (ETDEWEB)

Kask, Ue.; Andrijevskaja, J.; Kask, L. [and others

2012-11-01

The EU directive on the promotion of the use of energy from renewable sources (Directive 2009/28/EC) sets a mandatory minimum target for the use of fuels produced using renewable energy sources of 10% of total petrol and diesel consumption in the transport sector by the year 2020. In addition, it states that production of renewable fuels should be consistent with sustainable development and must not endanger biodiversity. In the INTERREG IVA Southern Finland - Estonia Sub-programme, efforts towards finding solutions to the tasks set by the EU were undertaken in co-operation with Finnish and Estonian researchers. The purpose of the 'From Waste to Traffic Fuel' (W-Fuel) project was to promote the sustainable production and use of biogas using locally-sourced biodegradable waste materials from the food and beverage industry and the agricultural and municipal sectors. The ultimate aim of the project was to upgrade the biogas (produced based on anaerobic digestion of biodegradable wastes, sludge, manure, slurry and energy crops) to biomethane with a methane content similar to natural gas, to be further used as transport fuel with the aim of reducing traffic-borne emissions, in particular CO{sub 2}. The project combined waste, energy and traffic solutions in order to decrease emissions, costs and the use of materials. Six case areas in southern Finland and northern Estonia were selected. The two case areas in Estonia were the counties of Harju and Laeaene-Viru in northern Estonia. The project aimed to promote waste and sludge prevention and to commence biogas production and its subsequent upgrading to biomethane for use as a renewable fuel. The project promoted regional businesses and employment in waste treatment and 'green energy' production. On basis of the gathered data, the biogas potentials and prerequisites of each case county were analysed. Furthermore, the environmental, economic and other regional effects of the different options were

Model documentation: Renewable Fuels Module of the National Energy Modeling System

Energy Technology Data Exchange (ETDEWEB)

1994-04-01

This report documents the objectives, analytical approach, and design of the National Energy Modeling System (NEMS) Renewable Fuels Module (RFM) as it related to the production of the 1994 Annual Energy Outlook (AEO94) forecasts. The report catalogues and describes modeling assumptions, computational methodologies, data inputs, and parameter estimation techniques. A number of offline analyses used in lieu of RFM modeling components are also described. This documentation report serves two purposes. First, it is a reference document for model analysts, model users, and the public interested in the construction and application of the RFM. Second, it meets the legal requirement of the Energy Information Administration (EIA) to provide adequate documentation in support of its models. The RFM consists of six analytical submodules that represent each of the major renewable energy resources -- wood, municipal solid waste (MSW), solar energy, wind energy, geothermal energy, and alcohol fuels. Of these six, four are documented in the following chapters: municipal solid waste, wind, solar and biofuels. Geothermal and wood are not currently working components of NEMS. The purpose of the RFM is to define the technological and cost characteristics of renewable energy technologies, and to pass these characteristics to other NEMS modules for the determination of mid-term forecasted renewable energy demand.

CNG: a potential transport fuel

International Nuclear Information System (INIS)

Anon.

1992-01-01

Compressed Natural Gas (CNG) is an alternative transport fuel. Advantages of its use are briefly described. Infra structural requirements, if it is to be used in India are outlined. Applications of CNG as transport fuel for buses and trucks in India are discussed. (P.R.K.). 5 refs

Intermodal transportation of spent fuel

International Nuclear Information System (INIS)

Elder, H.K.

1983-09-01

Concepts for transportation of spent fuel in rail casks from nuclear power plant sites with no rail service are under consideration by the US Department of Energy in the Commercial Spent Fuel Management program at the Pacific Northwest Laboratory. This report identifies and evaluates three alternative systems for intermodal transfer of spent fuel: heavy-haul truck to rail, barge to rail, and barge to heavy-haul truck. This report concludes that, with some modifications and provisions for new equipment, existing rail and marine systems can provide a transportation base for the intermodal transfer of spent fuel to federal interim storage facilities. Some needed land transportation support and loading and unloading equipment does not currently exist. There are insufficient shipping casks available at this time, but the industrial capability to meet projected needs appears adequate

Hydrogen, fuel cells and renewable energy integration in islands

International Nuclear Information System (INIS)

Bauen, A.; Hart, D.; Foradini, F.; Hart, D.

2002-01-01

Remote areas such as islands rely on costly and highly polluting diesel and heavy fuel oil for their electricity supply. This paper explored the opportunities for exploiting economically and environmentally viable renewable energy sources, in particular hydrogen storage, on such islands. In particular, this study focused on addressing the challenge of matching energy supply with demand and with technical issues regarding weak grids that are hindered with high steady state voltage levels and voltage fluctuations. The main technical characteristics of integrated renewable energy and hydrogen systems were determined by modelling a case study for the island of El Hierro (Canary Islands). The paper referred to the challenges regarding the technical and economic viability of such systems and their contribution to the economic development of remote communities. It was noted that energy storage plays an important role in addressing supply and demand issues by offering a way to control voltage and using surplus electricity at times of low load. Electrical energy can be stored in the form of potential or chemical energy. New decentralized generation technologies have also played a role in improving the energy efficiency of renewable energy sources. The feasibility of using hydrogen for energy storage was examined with particular reference to fuel-cell based energy supply in isolated island communities. 4 refs., 5 figs

Transportable Hydrogen Research Plant Based on Renewable Energy

International Nuclear Information System (INIS)

Mikel Fernandez; Carlos Madina; Asier Gil de Muro; Jose Angel Alzolab; Iker Marino; Javier Garcia-Tejedor; Juan Carlos Mugica; Inaki Azkkrate; Jose Angel Alzola

2006-01-01

Efficiency and cost are nowadays the most important barriers for the penetration of systems based on hydrogen and renewable energies. According to this background, TECNALIA Corporation has started in 2004 the HIDROTEC project: 'Hydrogen Technologies for Renewable Energy Applications'. The ultimate aim of this project is the implementation of a multipurpose demonstration and research plant in order to explore diverse options for sustainable energetic solutions based on hydrogen. The plant is conceived as an independent system that can be easily transported and assembled. Research and demonstration activities can thus be carried out at very different locations, including commercial renewable facilities. Modularity and scalability have also been taken into account for an optimised exploitation. (authors)

Renewable Energy: Solar Fuels GRC and GRS

Energy Technology Data Exchange (ETDEWEB)

Lewis, Nathan [California Inst. of Technology (CalTech), Pasadena, CA (United States); Gray, Nancy Ryan [Gordon Research Conferences, West Kingston, RI (United States)

2010-02-26

This Gordon Research Conference seeks to bring together chemists, physicists, materials scientists and biologists to address perhaps the outstanding technical problem of the 21st Century - the efficient, and ultimately economical, storage of energy from carbon-neutral sources. Such an advance would deliver a renewable, environmentally benign energy source for the future. A great technological challenge facing our global future is energy. The generation of energy, the security of its supply, and the environmental consequences of its use are among the world's foremost geopolitical concerns. Fossil fuels - coal, natural gas, and petroleum - supply approximately 90% of the energy consumed today by industrialized nations. An increase in energy supply is vitally needed to bring electric power to the 25% of the world's population that lacks it, to support the industrialization of developing nations, and to sustain economic growth in developed countries. On the geopolitical front, insuring an adequate energy supply is a major security issue for the world, and its importance will grow in proportion to the singular dependence on oil as a primary energy source. Yet, the current approach to energy supply, that of increased fossil fuel exploration coupled with energy conservation, is not scaleable to meet future demands. Rising living standards of a growing world population will cause global energy consumption to increase significantly. Estimates indicate that energy consumption will increase at least two-fold, from our current burn rate of 12.8 TW to 28 - 35 TW by 2050. - U.N. projections indicate that meeting global energy demand in a sustainable fashion by the year 2050 will require a significant fraction of the energy supply to come carbon free sources to stabilize atmospheric carbon dioxide levels at twice the pre-anthropogenic levels. External factors of economy, environment, and security dictate that this global energy need be met by renewable and sustainable

Fuel Cell System for Transportation -- 2005 Cost Estimate

Energy Technology Data Exchange (ETDEWEB)

Wheeler, D.

2006-10-01

Independent review report of the methodology used by TIAX to estimate the cost of producing PEM fuel cells using 2005 cell stack technology. The U.S. Department of Energy (DOE) Hydrogen, Fuel Cells and Infrastructure Technologies Program Manager asked the National Renewable Energy Laboratory (NREL) to commission an independent review of the 2005 TIAX cost analysis for fuel cell production. The NREL Systems Integrator is responsible for conducting independent reviews of progress toward meeting the DOE Hydrogen Program (the Program) technical targets. An important technical target of the Program is the proton exchange membrane (PEM) fuel cell cost in terms of dollars per kilowatt ($/kW). The Program's Multi-Year Program Research, Development, and Demonstration Plan established $125/kW as the 2005 technical target. Over the last several years, the Program has contracted with TIAX, LLC (TIAX) to produce estimates of the high volume cost of PEM fuel cell production for transportation use. Since no manufacturer is yet producing PEM fuel cells in the quantities needed for an initial hydrogen-based transportation economy, these estimates are necessary for DOE to gauge progress toward meeting its targets. For a PEM fuel cell system configuration developed by Argonne National Laboratory, TIAX estimated the total cost to be $108/kW, based on assumptions of 500,000 units per year produced with 2005 cell stack technology, vertical integration of cell stack manufacturing, and balance-of-plant (BOP) components purchased from a supplier network. Furthermore, TIAX conducted a Monte Carlo analysis by varying ten key parameters over a wide range of values and estimated with 98% certainty that the mean PEM fuel cell system cost would be below DOE's 2005 target of $125/kW. NREL commissioned DJW TECHNOLOGY, LLC to form an Independent Review Team (the Team) of industry fuel cell experts and to evaluate the cost estimation process and the results reported by TIAX. The results of

Managing aging effects on dry cask storage systems for extended long-term storage and transportation of used fuel - rev. 0

Energy Technology Data Exchange (ETDEWEB)

Chopra, O.K.; Diercks, D.; Fabian, R.; Ma, D.; Shah, V.; Tam, S.W.; Liu, Y. (Decision and Information Sciences); ( EVS); ( NE)

2012-07-06

The cancellation of the Yucca Mountain repository program in the United States raises the prospect of extended long-term storage (i.e., >120 years) and deferred transportation of used fuel at operating and decommissioned nuclear power plant sites. Under U.S. federal regulations contained in Title 10 of the Code of Federal Regulations (CFR) 72.42, the initial license term for an Independent Spent Fuel Storage Installation (ISFSI) must not exceed 40 years from the date of issuance. Licenses may be renewed by the U.S. Nuclear Regulatory Commission (NRC) at the expiration of the license term upon application by the licensee for a period not to exceed 40 years. Application for ISFSI license renewals must include the following: (1) Time-limited aging analyses (TLAAs) that demonstrate that structures, systems, and components (SSCs) important to safety will continue to perform their intended function for the requested period of extended operation; and (2) a description of the aging management program (AMP) for management of issues associated with aging that could adversely affect SSCs important to safety. In addition, the application must also include design bases information as documented in the most recent updated final safety analysis report as required by 10 CFR 72.70. Information contained in previous applications, statements, or reports filed with the Commission under the license may be incorporated by reference provided that those references are clear and specific. The NRC has recently issued the Standard Review Plan (SRP) for renewal of used-fuel dry cask storage system (DCSS) licenses and Certificates of Compliance (CoCs), NUREG-1927, under which NRC may renew a specific license or a CoC for a term not to exceed 40 years. Both the license and the CoC renewal applications must contain revised technical requirements and operating conditions (fuel storage, surveillance and maintenance, and other requirements) for the ISFSI and DCSS that address aging effects that

Standard casks for the transport of LWR spent fuel. Storage/transport casks for long cooled spent fuel

International Nuclear Information System (INIS)

Blum, P.; Sert, G.; Gagnon, R.

1983-01-01

During the past decade, TRANSNUCLEAIRE has developed, licensed and marketed a family of standard casks for the transport of spent fuel from LWR reactors to reprocessing plants and the ancillary equipments necessary for their operation and transport. A large number of these casks are presently used for European and intercontinental transports and manufactured under TRANSNUCLEAIRE supervision in different countries. The main advantages of these casks are: - large payload for considered modes of transport, - moderate cost, - reliability due to the large experience gained by TRANSNUCLEAIRE as concerns fabrication and operation problems, - standardization faciliting fabrication, operation and spare part supply. Recently, TRANSNUCLEAIRE also developed a new generation of casks for the dry storage and occasional transport of LWR spent fuel which has been cooled for 5 years or 7 years in case of consolidated fuel rods. These casks have an optimum payload which takes into account the shielding requirements and the weight limitations at most sites. This paper deals more particularly with the TN 24 model which exists in 4 versions among which one for 24 PWR 900 fuel assemblies and another one for the consolidated fuel rods from 48 of same fuel assemblies

Renewable Energy Policy Fact sheet - Latvia

International Nuclear Information System (INIS)

2017-09-01

The EurObserv'ER policy profiles give a snapshot of the renewable energy policy in the EU Member States. Electricity from renewable sources of energy is stimulated by a feed-in tariff scheme which includes elements of a renewable quota scheme and tendering. Since 2011 this scheme only applies to pre-existing RES-E installations and is closed for new RES-E projects. Moreover, the present main RES-E support scheme is being evaluated which may result in reforms within short. Small-scale renewable generation, notably PV, is stimulated by net metering. On the other hand, since January 2014 a tax for subsidised electricity generators is in place. Renewable heating and cooling is promoted by fiscal instruments. To date, renewable transport fuels are promoted through a tax mechanism as well

Cost reductions of fuel cells for transport applications: fuel processing options

Energy Technology Data Exchange (ETDEWEB)

Teagan, W P; Bentley, J; Barnett, B [Arthur D. Little, Inc., Cambridge, MA (United States)

1998-03-15

The highly favorable efficiency/environmental characteristics of fuel cell technologies have now been verified by virtue of recent and ongoing field experience. The key issue regarding the timing and extent of fuel cell commercialization is the ability to reduce costs to acceptable levels in both stationary and transport applications. It is increasingly recognized that the fuel processing subsystem can have a major impact on overall system costs, particularly as ongoing R and D efforts result in reduction of the basic cost structure of stacks which currently dominate system costs. The fuel processing subsystem for polymer electrolyte membrane fuel cell (PEMFC) technology, which is the focus of transport applications, includes the reformer, shift reactors, and means for CO reduction. In addition to low cost, transport applications require a fuel processor that is compact and can start rapidly. This paper describes the impact of factors such as fuel choice operating temperature, material selection, catalyst requirements, and controls on the cost of fuel processing systems. There are fuel processor technology paths which manufacturing cost analyses indicate are consistent with fuel processor subsystem costs of under $150/kW in stationary applications and $30/kW in transport applications. As such, the costs of mature fuel processing subsystem technologies should be consistent with their use in commercially viable fuel cell systems in both application categories. (orig.)

Transport and reprocessing of irradiated nuclear fuel

International Nuclear Information System (INIS)

Lenail, B.

1981-01-01

This contribution deals with transport and packaging of oxide fuel from and to the Cogema reprocessing plant at La Hague (France). After a general discussion of nuclear fuel and the fuel cycle, the main aspects of transport and reprocessing of oxide fuel are analysed. (Auth.)

77 FR 8254 - Notice of Data Availability Concerning Renewable Fuels Produced From Palm Oil Under the RFS...

Science.gov (United States)

2012-02-14

... Concerning Renewable Fuels Produced From Palm Oil Under the RFS Program; Extension of Comment Period AGENCY... of Data Availability Concerning Renewable Fuels Produced From Palm Oil Under the RFS Program'' (the notice is herein referred to as the ``palm oil NODA''). EPA published a NODA, which included a request...

77 FR 19663 - Notice of Data Availability Concerning Renewable Fuels Produced from Palm Oil Under the RFS...

Science.gov (United States)

2012-04-02

... Concerning Renewable Fuels Produced from Palm Oil Under the RFS Program; Extension of Comment Period AGENCY... of Data Availability Concerning Renewable Fuels Produced from Palm Oil under the RFS Program'' (the notice is herein referred to as the ``palm oil NODA''). EPA published a NODA, which included a request...

Fuel cell water transport

Science.gov (United States)

Vanderborgh, Nicholas E.; Hedstrom, James C.

1990-01-01

The moisture content and temperature of hydrogen and oxygen gases is regulated throughout traverse of the gases in a fuel cell incorporating a solid polymer membrane. At least one of the gases traverses a first flow field adjacent the solid polymer membrane, where chemical reactions occur to generate an electrical current. A second flow field is located sequential with the first flow field and incorporates a membrane for effective water transport. A control fluid is then circulated adjacent the second membrane on the face opposite the fuel cell gas wherein moisture is either transported from the control fluid to humidify a fuel gas, e.g., hydrogen, or to the control fluid to prevent excess water buildup in the oxidizer gas, e.g., oxygen. Evaporation of water into the control gas and the control gas temperature act to control the fuel cell gas temperatures throughout the traverse of the fuel cell by the gases.

The first decade: 2004 - 2014. 10 years of renewable energy progress

International Nuclear Information System (INIS)

Lins, Christine; Williamson, Laura E.; Leitner, Sarah; Teske, Sven; Hankins, Mark; Sosis, Karin; Kiene, Ansgar; Mali, Thembakazi; Auth, Katie; Musolino, Evan; Iida, Tetsunari; Thornton, Kane; Haugwitz, Frank; Hinrichs-Rahlwes, Rainer; Subramanian, Venkataraman; Bravo, Gonzalo; McQueen, Dane; Sawin, Janet L.; Wiser, Ryan; Schweinfurth, Arne

2014-01-01

The evolution of renewable energy over the past decade has surpassed all expectations. Global installed capacity and production from all renewable technologies have increased substantially, and supporting policies have continued to spread to more countries in all regions of the world. Developments in the early 2000's showed upward trends in global renewable energy investment, capacity, and integration across all sectors, yet most mainstream projections did not predict the extraordinary expansion of renewables that was to unfold over the decade ahead. Several factors set the foundation for this rapid growth. The various energy crises-beginning in the 1970's - and the subsequent economic downturns underscored the role of energy for both national and economic security. At the same time, a handful of pioneering countries-such as Germany, Denmark, Spain, and the United States-created critical markets for renewables, which drove early technological advances and economies of scale, setting the stage and helping to fuel the past decade of explosive market expansion. Growing emphasis on mitigating climate change and adapting to its impacts has further contributed to the momentum. Renewable energy's contribution to the global heat, power and transport sectors has increased steadily. While growth in renewable's share of total energy use has been moderated by increases in both population and world energy demand-most notably in developing and emerging economies-renewable energy markets and technology developments have accelerated quickly, even when compared to other rapidly developing technologies such as mobile phones. Although the last decade has seen tremendous advances in the electricity sector, the renewable heating and cooling sector has lagged behind. This is despite the marked growth since 2004 in the use of geothermal, solar thermal, and biomass heating technologies for water and space heating, process heat, and cooling. Given that the share of

Estimating road transport fuel consumption in Ecuador

International Nuclear Information System (INIS)

Sierra, Jaime Cevallos

2016-01-01

Road transport is one of the sectors with highest energy consumptions in the planet, with large dependence of fossil fuels, and contribution for global greenhouse gas emissions. Although, Latin America is not a high-energy consumer, its share in global consumption is expected to grow, especially in the transportation sector. This make essential for developing countries the adoption of better policies to identify the vehicle groups with largest fuel demands. The present study describes the VKT technique to disaggregate road transport energy consumption by vehicle type, applied to the road transportation system of Ecuador. It also describes the procedures performed to estimate the variables required to run the model, and some of the practical applications that be used to create public policies. Results show as the biggest fuel consumers the heavy-duty freight cargo, followed by light duty vehicles. The estimation of greenhouse gas emissions evidence that road transport released 14.3 million tons of CO_2 in 2012. When fuel consumption is compared by it costs, it can be confirmed that Ecuadorean Government covered, through subsidies, for 68% of the annual fuel costs of national road transport, demonstrating the importance of restructuring these expenditures in order to achieve an efficient road transport system. - Highlights: •The vehicle-kilometers traveled has been estimated from local info. •The fuel economy has been calculated from national and international data. •The groups with higher fuel consumption has been located. •The fuel-type dependency has been estimated for each vehicle group. •Greenhouse gas emission, and fuel costs, has been estimated for local road transport.

Methods of producing transportation fuel

Science.gov (United States)

Nair, Vijay [Katy, TX; Roes, Augustinus Wilhelmus Maria [Houston, TX; Cherrillo, Ralph Anthony [Houston, TX; Bauldreay, Joanna M [Chester, GB

2011-12-27

Systems, methods, and heaters for treating a subsurface formation are described herein. At least one method for producing transportation fuel is described herein. The method for producing transportation fuel may include providing formation fluid having a boiling range distribution between -5.degree. C. and 350.degree. C. from a subsurface in situ heat treatment process to a subsurface treatment facility. A liquid stream may be separated from the formation fluid. The separated liquid stream may be hydrotreated and then distilled to produce a distilled stream having a boiling range distribution between 150.degree. C. and 350.degree. C. The distilled liquid stream may be combined with one or more additives to produce transportation fuel.

Alternative Fuels Data Center: Indiana Transportation Data for Alternative

Science.gov (United States)

(nameplate, MW) 1,430 Source: BioFuels Atlas from the National Renewable Energy Laboratory Case Studies Video Alternative Fuels Save Money in Indy April 1, 2012 More Case Studies Videos Text Version More Indiana Videos on YouTube Video thumbnail for Indiana Beverage Company Invests in Alternative Fuels Indiana Beverage

Renewable energies and energy choices. Summary of the colloquium

International Nuclear Information System (INIS)

2003-05-01

This document is an executive summary of the colloquium organized by the French syndicate of renewable energies (SER) which took place at the Maison de l'UNESCO in Paris during the national debate on energies organized by the French government in spring 2003. The colloquium was organized around 6 round tables dealing with: the world perspectives and the environmental context of the contribution of renewable energies to the sustainable development (respect of Kyoto protocol commitments, contribution to the security of energy supplies, lack of large scale program of development of decentralized power generation in developing countries, lack of market tools linked with CO 2 emissions, improvement of competitiveness); development of renewable energies in Europe (promotion and sustain in all European countries, obligation of supply and purchase, pricing regulation, European harmonization of practices); renewable electricity and its place in the new orientation law about energies (tariff/pluri-annual investment planing, administrative authorizations, connections to the grid, calls for offer, costs of the photovoltaic solar energy); contribution of renewable energies in the transportation sector (bio-fuels, low taxes, ethanol fuel cells, vegetal chemistry); renewable heat and integration of renewable energy sources in buildings (intelligent architecture, promotion, quality labels and standards, lack of CO 2 penalties linked with fossil fuels, tax reduction for solar and wood fuel appliances, acknowledgment of geothermal heat pumps as renewable energy source); and the presentation of the first proposals for the future orientation law (balance between nuclear and renewable energy sources, integration in the local environment, competitiveness, use of market mechanisms, R and D etc.). (J.S.)

Transport of MOX fuel from Europe to Japan

International Nuclear Information System (INIS)

2002-01-01

The MOX fuel transports from Europe to Japan represent a main part in the implementing of the Japan nuclear program. They complement the 160 transports of spent fuels realized from Japan to Europe and the vitrified residues return from France to Japan. In this framework the document presents the MOX fuel, the use of the MOX fuel in reactor, the proliferation risks, the MOX fuel transport to Japan, the public health, the transport regulations, the safety and the civil liability. (A.L.B.)

From fossil fuels to energies-of-light

Energy Technology Data Exchange (ETDEWEB)

Winter, C.J. [Stuttgart Univ. (Germany); Energon - Winter (C.J.) GmbH, Leonberg (Germany)

2000-07-01

Energies-of-light are the final result on the ongoing decarbonisation of carbonaceous fuels, their hydrogenation and, thus, dematerialization (coal -> petroleum -> natural gas -> hydrogen). Energies-of-light utilise all sorts of renewable energies and the chemical secondary energy carrier hydrogen for energy storage and transport, as well as a transportation fuel.

Spent fuel transport in fuel cycle

International Nuclear Information System (INIS)

Labrousse, M.

1977-01-01

The transport of radioactive substances is a minor part of the fuel cycle because the quantities of matter involved are very small. However the length and complexity of the cycle, the weight of the packing, the respective distances between stations, enrichment plants and reprocessing plants are such that the problem is not negligible. In addition these transports have considerable psychological importance. The most interesting is spent fuel transport which requires exceptionally efficient packaging, especially where thermal and mechanical resistance are concerned. To meet the safety criteria necessary for the protection of both public and users it was decided to use the maximum capacity consistent with rail transport and to avoid coolant fluids under pressure. Since no single type of packing is suitable for all existing stations an effort has been made to standardise handling accessories, and future trands are towards maximum automation. A discussion on the various technical solutions available for the construction of these packing systems is followed by a description of those used for the two types of packaging ordered by COGEMA [fr

Life-cycle global warming and non-renewable energy consumption impacts of ammonia fuel

International Nuclear Information System (INIS)

Are, Kristian Ray Angelo; Razon, Luis; Tan, Raymond Girard

2015-01-01

The use of ammonia (NH 3 ) as transportation fuel had been a recent topics of research interest. NH 3 has fuel properties that are better than those of other alternative fuels, such as it high energy density and simpler storage. However, it has a low flame speed and would require to be mixed with a secondary fuel forming a dual fuel system. Moreover, current industrial methods of NH 3 production are major global warming potential (GWP) and non-renewable energy consumption (NREC) impact contributors. This study assessed the life-cycle GWP and NREC of using different NH 3 -secondary fuel mixtures. Four fuel mixtures were considered, wherein NH 3 is mixed with gasoline, diesel, hydrogen or dimethyl ether (DME). Also, our processes of NH 3 production were considered: steam reforming (SR), partial oxidation (PO), which are industrial methods and two biomass-based (alternative) processes wherein cereal straw (Salix) and cyanobacteria (Anabaena ATCC 33047) are used feedstocks. Contribution, sensitivity, and uncertainty analyses (via Monte Carlo simulation) were conducted for life-cycle interpretation. Dominance matrix tool was also employed to aid in drawing conclusions. The study concludes that the environmental impacts of NH 3 fuel are dependent on (i) NH 3 production methods and (ii) type of NH 3 fuel mixture. NH 3 -diesel fuel mixtures have lower GWP compared to pure diesel, while NH 3 -gasoline fuel mixture have higher GWP compared to pure gasoline. Because of large uncertainty of the NREC pure gasoline and pure diesel, no firm conclusion can be made about the NREC ammonia-diesel and ammonia-gasoline. If fuel mixture types are compared, NH 3 -H 2 mixtures have the lowest GWP and NREC among the four, though this would entail designing new engines. Over-all, it is shown that fuel systems involving biomass-based NH 3 have lower environmental impacts as compared to conventionally-produced NH 3 counterparts. (author)

Renewable energy carriers: Hydrogen or liquid air/nitrogen?

International Nuclear Information System (INIS)

Li Yongliang; Chen Haisheng; Zhang Xinjing; Tan Chunqing; Ding Yulong

2010-01-01

The world's energy demand is met mainly by the fossil fuels today. The use of such fuels, however, causes serious environmental issues, including global warming, ozone layer depletion and acid rains. A sustainable solution to the issues is to replace the fossil fuels with renewable ones. Implementing such a solution, however, requires overcoming a number of technological barriers including low energy density, intermittent supply and mobility of the renewable energy sources. A potential approach to overcoming these barriers is to use an appropriate energy carrier, which can store, transport and distribute energy. The work to be reported in this paper aims to assess and compare a chemical energy carrier, hydrogen, with a physical energy carrier, liquid air/nitrogen, and discuss potential applications of the physical carrier. The ocean energy is used as an example of the renewable energy sources in the work. The assessment and comparison are carried out in terms of the overall efficiency, including production, storage/transportation and energy extraction. The environmental impact, waste heat recovery and safety issues are also considered. It is found that the physical energy carrier may be a better alternative to the chemical energy carrier under some circumstances, particularly when there are waste heat sources.

Phenomena in thermal transport in fuels

International Nuclear Information System (INIS)

Chernatynskiy, A.; Tulenko, J.S.; Phillpot, S.R.; El-Azab, A.

2015-01-01

Thermal transport in nuclear fuels is a key performance metric that affects not only the power output, but is also an important consideration in potential accident situations. While the fundamental theory of the thermal transport in crystalline solids was extensively developed in the 1950's and 1960's, the pertinent analytic approaches contained significant simplifications of the physical processes. While these approaches enabled estimates of the thermal conductivity in bulk materials with microstructure, they were not comprehensive enough to provide the detailed guidance needed for the in-pile fuel performance. Rather, this guidance has come from data painfully accumulated over 50 years of experiments on irradiated uranium dioxide, the most widely used nuclear fuel. At this point, a fundamental theoretical understanding of the interplay between the microstructure and thermal conductivity of irradiated uranium dioxide fuel is still lacking. In this chapter, recent advances are summarised in the modelling approaches for thermal transport of uranium dioxide fuel. Being computational in nature, these modelling approaches can, at least in principle, describe in detail virtually all mechanisms affecting thermal transport at the atomistic level, while permitting the coupling of the atomistic-level simulations to the mesoscale continuum theory and thus enable the capture of the impact of microstructural evolution in fuel on thermal transport. While the subject of current studies is uranium dioxide, potential applications of the methods described in this chapter extend to the thermal performance of other fuel forms. (authors)

Transport fuel

DEFF Research Database (Denmark)

Ronsse, Frederik; Jørgensen, Henning; Schüßler, Ingmar

2014-01-01

Worldwide, the use of transport fuel derived from biomass increased four-fold between 2003 and 2012. Mainly based on food resources, these conventional biofuels did not achieve the expected emission savings and contributed to higher prices for food commod - ities, especially maize and oilseeds...

Performance Analyses of Renewable and Fuel Power Supply Systems for Different Base Station Sites

Directory of Open Access Journals (Sweden)

Josip Lorincz

2014-11-01

Full Text Available Base station sites (BSSs powered with renewable energy sources have gained the attention of cellular operators during the last few years. This is because such “green” BSSs impose significant reductions in the operational expenditures (OPEX of telecom operators due to the possibility of on-site renewable energy harvesting. In this paper, the green BSSs power supply system parameters detected through remote and centralized real time sensing are presented. An implemented sensing system based on a wireless sensor network enables reliable collection and post-processing analyses of many parameters, such as: total charging/discharging current of power supply system, battery voltage and temperature, wind speed, etc. As an example, yearly sensing results for three different BSS configurations powered by solar and/or wind energy are discussed in terms of renewable energy supply (RES system performance. In the case of powering those BSS with standalone systems based on a fuel generator, the fuel consumption models expressing interdependence among the generator load and fuel consumption are proposed. This has allowed energy-efficiency comparison of the fuel powered and RES systems, which is presented in terms of the OPEX and carbon dioxide (CO2 reductions. Additionally, approaches based on different BSS air-conditioning systems and the on/off regulation of a daily fuel generator activity are proposed and validated in terms of energy and capital expenditure (CAPEX savings.

Inspection of nuclear fuel transport in Spain

International Nuclear Information System (INIS)

Lobo Mendez, J.

1977-01-01

The experience acquired in inspecting nuclear fuel shipments carried out in Spain will serve as a basis for establishing the regulations wich must be adhered to for future transports, as the transport of nuclear fuels in Spain will increase considerably within the next years as a result of the Spanish nuclear program. The experience acquired in nuclear fuel transport inspection is described. (author) [es

Fossil Fuels: Factors of Supply Reduction and Use of The Renewable Energy As A Suitable Alternative

OpenAIRE

Askari Mohammad Bagher,

2015-01-01

In this article we will review the consumption of fossil fuels in the world. According to the exhaustible resources of fossil fuels, and the damaging effects of these fuels on the environment and nature, we introduce renewable energy sources as perfect replacement for fossil fuels.

Analysis of near-term spent fuel transportation hardware requirements and transportation costs

International Nuclear Information System (INIS)

Daling, P.M.; Engel, R.L.

1983-01-01

A computer model was developed to quantify the transportation hardware requirements and transportation costs associated with shipping spent fuel in the commercial nucler fuel cycle in the near future. Results from this study indicate that alternative spent fuel shipping systems (consolidated or disassembled fuel elements and new casks designed for older fuel) will significantly reduce the transportation hardware requirements and costs for shipping spent fuel in the commercial nuclear fuel cycle, if there is no significant change in their operating/handling characteristics. It was also found that a more modest cost reduction results from increasing the fraction of spent fuel shipped by truck from 25% to 50%. Larger transportation cost reductions could be realized with further increases in the truck shipping fraction. Using the given set of assumptions, it was found that the existing spent fuel cask fleet size is generally adequate to perform the needed transportation services until a fuel reprocessing plant (FRP) begins to receive fuel (assumed in 1987). Once the FRP opens, up to 7 additional truck systems and 16 additional rail systems are required at the reference truck shipping fraction of 25%. For the 50% truck shipping fraction, 17 additional truck systems and 9 additional rail systems are required. If consolidated fuel only is shipped (25% by truck), 5 additional rail casks are required and the current truck cask fleet is more than adequate until at least 1995. Changes in assumptions could affect the results. Transportation costs for a federal interim storage program could total about $25M if the FRP begins receiving fuel in 1987 or about $95M if the FRP is delayed until 1989. This is due to an increased utilization of federal interim storage facility from 350 MTU for the reference scenario to about 750 MTU if reprocessing is delayed by two years

Transport device for nuclear fuel powder

International Nuclear Information System (INIS)

Adelmann, M.

1987-01-01

The transport device for nuclear fuel powder, which does not disintegrate during transport, has a transport pipe which starts with its entry end from the floor or a closed container and opens with its outlet end at the top into a closed separation container connect via a powder filter to a suction pump. By alternate regular opening and closing of a first control valve for transport gas fitted to a transport pipe to a supply duct and a second control valve for transport gas fitted to the container to an additional supply duct, alternating plugs of nuclear fuel powder and transport gas cushions are formed and are transported to the outlet end of the transport pipe. (orig./HP) [de

Hydrogenation and hydrodeoxygenation of biomass-derived oxygenates to liquid alkanes for transportation fuels.

Science.gov (United States)

Sun, Shaohui; Yang, Ruishu; Wang, Xin; Yan, Shaokang

2018-04-01

An attractive approach for the production of transportation fuels from renewable biomass resources is to convert oxygenates into alkanes. In this paper, C 5 -C 20 alkanes formed via the hydrogenation and hydrodeoxygenation of the oligomers of furfuryl alcohol(FA) can be used as gasoline, diesel and jet fuel fraction. The first step of the process is the oligomers of FA convert into hydrogenated products over Raney Ni catalyst in a batch reactor. The second step of the process converts hydrogenated products to alkanes via hydrodeoxygenation over different bi-functional catalysts include hydrogenation and acidic deoxidization active sites. After this process, the oxygen content decreased from 22.1 wt% in the oligomers of FA to 0.58 wt% in the hydrodeoxygenation products.

Renewables 2015 global status report - Annual Reporting on Renewables: Ten years of excellence

International Nuclear Information System (INIS)

Sawin, Janet L.; Sverrisson, Freyr; Rickerson, Wilson; Lins, Christine; Williamson, Laura E.; Adib, Rana; Murdock, Hannah E.; Musolino, Evan; Hullin, Martin; Reith, Ayla; Valero, Alana; Mastny, Lisa; Petrichenko, Ksenia; Seyboth, Kristin; Skeen, Jonathan; Sovacool, Benjamin; Wouters, Frank; Martinot, Eric

2015-01-01

Renewable energy continued to grow in 2014 against the backdrop of increasing global energy consumption, particularly in developing countries, and a dramatic decline in oil prices during the second half of the year. Despite rising energy use, for the first time in four decades, global carbon emissions associated with energy consumption remained stable in 2014 while the global economy grew; this stabilisation has been attributed to increased penetration of renewable energy and to improvements in energy efficiency. Globally, there is growing awareness that increased deployment of renewable energy (and energy efficiency) is critical for addressing climate change, creating new economic opportunities, and providing energy access to the billions of people still living without modern energy services. Although discussion is limited to date, renewables also are an important element of climate change adaptation, improving the resilience of existing energy systems and ensuring delivery of energy services under changing climatic conditions. Renewable energy provided an estimated 19.1% of global final energy consumption in 2013, and growth in capacity and generation continued to expand in 2014. Heating capacity grew at a steady pace, and the production of bio-fuels for transport increased for the second consecutive year, following a slowdown in 2011-2012. The most rapid growth, and the largest increase in capacity, occurred in the power sector, led by wind, solar PV, and hydropower. Growth has been driven by several factors, including renewable energy support policies and the increasing cost-competitiveness of energy from renewable sources. In many countries, renewables are broadly competitive with conventional energy sources. At the same time, growth continues to be tempered by subsidies to fossil fuels and nuclear power, particularly in developing countries. Although Europe remained an important market and a centre for innovation, activity continued to shift towards other

Will Aerosol Hygroscopicity Change with Biodiesel, Renewable Diesel Fuels and Emission Control Technologies?

Science.gov (United States)

Vu, Diep; Short, Daniel; Karavalakis, Georgios; Durbin, Thomas D; Asa-Awuku, Akua

2017-02-07

The use of biodiesel and renewable diesel fuels in compression ignition engines and aftertreatment technologies may affect vehicle exhaust emissions. In this study two 2012 light-duty vehicles equipped with direct injection diesel engines, diesel oxidation catalyst (DOC), diesel particulate filter (DPF), and selective catalytic reduction (SCR) were tested on a chassis dynamometer. One vehicle was tested over the Federal Test Procedure (FTP) cycle on seven biodiesel and renewable diesel fuel blends. Both vehicles were exercised over double Environmental Protection Agency (EPA) Highway fuel economy test (HWFET) cycles on ultralow sulfur diesel (ULSD) and a soy-based biodiesel blend to investigate the aerosol hygroscopicity during the regeneration of the DPF. Overall, the apparent hygroscopicity of emissions during nonregeneration events is consistently low (κ diesel vehicles. As such, the contribution of regeneration emissions from a growing fleet of diesel vehicles will be important.

Power electronics for renewable energy systems, transportation and industrial applications

CERN Document Server

Malinowski, Mariusz; Al-Haddad, Kamal

2014-01-01

Power Electronics for Renewable Energy, Transportation, and Industrial Applications combines state-of-the-art global expertise to present the latest research on power electronics and its application in transportation, renewable energy, and different industrial applications. This timely book aims to facilitate the implementation of cutting-edge techniques to design problems offering innovative solutions to the growing power demands in small- and large-size industries. Application areas in the book range from smart homes and electric and plug-in hybrid electrical vehicles (PHEVs), to smart distribution and intelligence operation centers where significant energy efficiency improvements can be achieved through the appropriate use and design of power electronics and energy storage devices.

Alternatives to traditional transportation fuels 1996

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-12-01

Interest in alternative transportation fuels (ATF`s) has increased in recent years due to the drives for cleaner air and less dependence upon foreign oil. This report, Alternatives to Traditional Transportation Fuels 1996, provides information on ATFs, as well as the vehicles that consume them.

Renewables 2017 Global Status Report

International Nuclear Information System (INIS)

Sawin, Janet L.; Sverrisson, Freyr; Seyboth, Kristin; Adib, Rana; Murdock, Hannah E.; Lins, Christine; Edwards, Isobel; Hullin, Martin; Nguyen, Linh H.; Prillianto, Satrio S.; Satzinger, Katharina; Appavou, Fabiani; Brown, Adam; Chernyakhovskiy, Ilya; Logan, Jeffrey; Milligan, Michael; Zinaman, Owen; Epp, Baerbel; Huber, Lon; Lyons, Lorcan; Nowak, Thomas; Otte, Pia; Skeen, Jonathan; Sovacool, Benjamin; Witkamp, Bert; Musolino, Evan; Brown, Adam; Williamson, Laura E.; Ashworth, Lewis; Mastny, Lisa

2017-01-01

Renewable energy technologies increase their hold across developing and emerging economies throughout the year The year 2016 saw several developments and ongoing trends that all have a bearing on renewable energy, including the continuation of comparatively low global fossil fuel prices; dramatic price declines of several renewable energy technologies; and a continued increase in attention to energy storage. For the third consecutive year, global energy-related carbon dioxide emissions from fossil fuels and industry were nearly flat in 2016, due largely to declining coal use worldwide but also due to improvements in energy efficiency and to increasing use of renewable energy. As of 2015, renewable energy provided an estimated 19.3% of global final energy consumption, and growth in capacity and production continued in 2016. The power sector experienced the greatest increases in renewable energy capacity in 2016, whereas the growth of renewables in the heating and cooling and transport sectors was comparatively slow. Most new renewable energy capacity is installed in developing countries, and largely in China, the single largest developer of renewable power and heat over the past eight years. In 2016, renewable energy spread to a growing number of developing and emerging economies, some of which have become important markets. For the more than 1 billion people without access to electricity, distributed renewable energy projects, especially those in rural areas far from the centralised grid, offer important and often cost-effective options to provide such access. The renewable energy sector employed 9.8 million people in 2016, an increase of 1.1% over 2015. By technology, solar PV and biofuels provided the largest numbers of jobs. Employment shifted further towards Asia, which accounted for 62% of all renewable energy jobs (not including large-scale hydropower), led by China. The development of community renewable energy projects continued in 2016, but the pace of

Renewable fuels from agricultural sources - ethanol, biodiesel, biogas; Foernybara drivmedel fraan jordbruket - etanol, biodiesel, biogas

Energy Technology Data Exchange (ETDEWEB)

Tolke, Camilla L; Einarson, Elin; Ekloef, Patrik

2011-07-01

In this report we give a status report of the biofuels market. We describe some of the issues which are linked to environmental and land use. We also explain why different actors reach different assessments regarding the greenhouse gas emissions, land use and food security. Biofuels have been highlighted as a way to reduce the transport sector large emissions of greenhouse gases and thus as a climate measure. But when several countries have increased their production and consumption and set targets for bio-renewable fuels the biofuels impact has been questioned. Are emissions really reduced? What happens to the direct and indirect land use? How does the production of more biofuels affect the security in food production?

Multi-fuel reformers for fuel cells used in transportation. Phase 1: Multi-fuel reformers

Science.gov (United States)

1994-05-01

DOE has established the goal, through the Fuel Cells in Transportation Program, of fostering the rapid development and commercialization of fuel cells as economic competitors for the internal combustion engine. Central to this goal is a safe feasible means of supplying hydrogen of the required purity to the vehicular fuel cell system. Two basic strategies are being considered: (1) on-board fuel processing whereby alternative fuels such as methanol, ethanol or natural gas stored on the vehicle undergo reformation and subsequent processing to produce hydrogen, and (2) on-board storage of pure hydrogen provided by stationary fuel processing plants. This report analyzes fuel processor technologies, types of fuel and fuel cell options for on-board reformation. As the Phase 1 of a multi-phased program to develop a prototype multi-fuel reformer system for a fuel cell powered vehicle, the objective of this program was to evaluate the feasibility of a multi-fuel reformer concept and to select a reforming technology for further development in the Phase 2 program, with the ultimate goal of integration with a DOE-designated fuel cell and vehicle configuration. The basic reformer processes examined in this study included catalytic steam reforming (SR), non-catalytic partial oxidation (POX) and catalytic partial oxidation (also known as Autothermal Reforming, or ATR). Fuels under consideration in this study included methanol, ethanol, and natural gas. A systematic evaluation of reforming technologies, fuels, and transportation fuel cell applications was conducted for the purpose of selecting a suitable multi-fuel processor for further development and demonstration in a transportation application.

Fuel price impacts and compliance costs associated with the Renewable Fuel Standard (RFS)

International Nuclear Information System (INIS)

Christensen, Adam; Siddiqui, Sauleh

2015-01-01

US policy instruments concerning vehicle biofuels are currently being revisited. For example, as part of an on-going annual Renewable Fuel Standard (RFS) implementation, the Environmental Protection Agency (EPA) requests stakeholder feedback/analysis of programmatic effects, including impacts on gasoline/diesel prices and compliance costs. Motivated by the need for regulatory-specific feedback, a novel regional market model is developed that quantifies price impacts across different regional markets for a number of market variables, including several types of compliance certificates known as Renewable Identification Numbers (RINs). An analysis of the most recent EPA proposal suggests that the D4 (biodiesel) RIN price could rise to >$1.00/RIN. Sensitivity results show that the D4 RIN price is highly sensitive to soybean oil prices, while D5/D6 RIN prices are most sensitive to the volume of E85 consumed. It was found that the projected costs associated with the RFS in 2017 could be reduced by approximately 50% if an additional 600 million gallons of E85 were consumed. The analysis also suggests that the RFS does not dramatically affect the retail price of either gasoline and diesel fuels paid by consumers. - Highlights: • The most recent EPA could cause the biodiesel RIN price to rise to >$1.00/RIN. • D5/D6 RIN prices are most sensitive to the volume of E85 consumed. • Retail prices for fuel do not change dramatically. • 2017 compliance costs could fall by 50% if more E85 were consumed.

Production of Solid Fuel by Torrefaction Using Coconut Leaves As Renewable Biomass

Directory of Open Access Journals (Sweden)

Lola Domnina Bote Pestaño

2016-11-01

Full Text Available The reserves of non-renewable energy sources such as coal, crude oil and natural gas are not limitless, they gradually get exhausted and their price continually increases. In the last four decades, researchers have been focusing on alternate fuel resources to meet the ever increasing energy demand and to avoid dependence on crude oil. Amongst different sources of renewable energy, biomass residues hold special promise due to their inherent capability to store solar energy and amenability to subsequent conversion to convenient solid, liquid and gaseous fuels. At present, among the coconut farm wastes such as husks, shell, coir dust and coconut leaves, the latter is considered the most grossly under-utilized by in situ burning in the coconut farm as means of disposal. In order to utilize dried coconut leaves and to improve its biomass properties, this research attempts to produce solid fuel by torrefaction using dried coconut leaves for use as alternative source of energy. Torrefaction is a thermal method for the conversion of biomass operating in the low temperature range of 200oC-300oC under atmospheric conditions in absence of oxygen. Dried coconut leaves were torrefied at different feedstock conditions. The key torrefaction products were collected and analyzed. Physical and combustion characteristics of both torrefied and untorrefied biomass were investigated. Torrefaction of dried coconut leaves significantly improved the heating value compared to that of the untreated biomass.  Proximate compositions of the torrefied biomass also improved and were comparable to coal. The distribution of the products of torrefaction depends highly on the process conditions such as torrefaction temperature and residence time. Physical and combustion characteristics of torrefied biomass were superior making it more suitable for fuel applications. Article History: Received June 24th 2016; Received in revised form August 16th 2016; Accepted 27th 2016; Available

The effects of rising energy costs and transportation mode mix on forest fuel procurement costs

International Nuclear Information System (INIS)

Rauch, Peter; Gronalt, Manfred

2011-01-01

Since fossil fuels have been broadly recognized as a non-renewable energy source that threatens the climate, sustainable and CO 2 neutral energy sources - such as forest fuels - are being promoted in Europe, instead. With the expeditiously growing forest fuel demand, the strategic problem of how to design a cost-efficient distribution network has evolved. This paper presents an MILP model, comprising decisions on modes of transportation and spatial arrangement of terminals, in order to design a forest fuel supply network for Austria. The MILP model is used to evaluate the impacts of rising energy costs on procurement sources, transport mix and procurement costs on a national scale, based on the example of Austria. A 20% increase of energy costs results in a procurement cost increase of 7%, and another 20% increase of energy costs would have similar results. While domestic waterways become more important as a result of the first energy cost increase, rail only does so after the second. One way to decrease procurement costs would be to reduce the share of empty trips with truck and trailer. Reducing this share by 10% decreases the average procurement costs by up to 20%. Routing influences the modal split considerably, and the truck transport share increases from 86% to 97%, accordingly. Increasing forest fuel imports by large CHPs lowers domestic competition and also enables smaller plants to cut their procurement costs. Rising forest fuel imports via ship will not significantly decrease domestic market shares, but they will reduce procurement costs considerably. (author)

Alternative Fuels and Sustainable Development

DEFF Research Database (Denmark)

Jørgensen, Kaj; Nielsen, Lars Henrik

1996-01-01

The main report of the project on Transportation Fuels based on Renewable Energy. The report contains a review of potential technologies for electric, hybrid and hydrogen propulsion in the Danish transport sector, including an assessment of their development status. In addition, the energy...

Hydrogen for transport in Denmark towards 2050. Contribution to electric-powered transport, growth, CO{sub 2} reduction and independence of fossil fuels; Brint til transport i Danmark frem mod 2050. Bidrag til elektrisk transport, vaekst, CO{sub 2} reduktion og fossil uafhaengighed. Baggrundsrapport. Endelig udgave

Energy Technology Data Exchange (ETDEWEB)

Wennike, F. (Hydrogen Link Danmark (Denmark)); Mortensgaard, A. (Brint and Braendselscelle Partnerskabet, Copenhagen (Denmark)); Sloth, M. (H2 Logic A/S, Herning (Denmark))

2011-12-15

Significant funding has been invested internationally in the development of hydrogen and fuel cells for the last 10 years, among others by the leading car makers. In Denmark alone businesses have, along with contributions from public programs, invested two billion DKK since 2001. The investments have helped to develop and mature hydrogen and fuel cells so that a deployment can be initiated from 2015. With the Danish government's new initiative, ''Our Energy'', which is targeted towards a switch to a fossil fuel-independent society in 2050, it is obvious that hydrogen is included as one of many technologies that can help solve the challenge within the transport sector. The Hydrogen Link Denmark Association and selected Danish players in the Hydrogen and Fuel Cell Partnership in Denmark has therefore prepared this analysis which describes a possible contribution to electrical transport, growth, CO{sub 2} reduction and fossil fuel independence by introduction of hydrogen for transport in Denmark up to 2050. The analysis is based on a possible share of hydrogen cars in the Danish car fleet in 2050 of 50% and the secondary effects of activation of the energy policy objectives for fossil fuel independence, and not least the significant potential for Danish exports of hydrogen and fuel cell technology and affected jobs. Similarly, the contribution of hydrogen for transport in relation to balancing the increased share of fluctuating renewable energy production was analyzed. (LN)

Dynamic life cycle assessment (LCA) of renewable energy technologies

Energy Technology Data Exchange (ETDEWEB)

Pehnt, M. [Institut for Energy and Environmental Research, Heidelberg (Germany)

2006-01-01

Before new technologies enter the market, their environmental superiority over competing options must be asserted based on a life cycle approach. However, when applying the prevailing status-quo Life Cycle Assessment (LCA) approach to future renewable energy systems, one does not distinguish between impacts which are 'imported' into the system due to the 'background system' (e.g. due to supply of materials or final energy for the production of the energy system), and what is the improvement potential of these technologies compared to competitors (e.g. due to process and system innovations or diffusion effects). This paper investigates a dynamic approach towards the LCA of renewable energy technologies and proves that for all renewable energy chains, the inputs of finite energy resources and emissions of greenhouse gases are extremely low compared with the conventional system. With regard to the other environmental impacts the findings do not reveal any clear verdict for or against renewable energies. Future development will enable a further reduction of environmental impacts of renewable energy systems. Different factors are responsible for this development, such as progress with respect to technical parameters of energy converters, in particular, improved efficiency; emissions characteristics; increased lifetime, etc.; advances with regard to the production process of energy converters and fuels; and advances with regard to 'external' services originating from conventional energy and transport systems, for instance, improved electricity or process heat supply for system production and ecologically optimized transport systems for fuel transportation. The application of renewable energy sources might modify not only the background system, but also further downstream aspects, such as consumer behavior. This effect is, however, strongly context and technology dependent. (author)

Exergy and environmental comparison of the end use of vehicle fuels: The Brazilian case

International Nuclear Information System (INIS)

Flórez-Orrego, Daniel; Silva, Julio A.M.; Oliveira Jr, Silvio de

2015-01-01

Highlights: • Total and non-renewable exergy costs of Brazilian transportation service are evaluated. • Specific CO 2 emissions of the Brazilian transportation service are determined. • Overall exergy efficiency of the end use of vehicle fuels in transportation sector is calculated. • A comparative extended analysis of the production and end use of transportation fuels is presented. - Abstract: In this work, a comparative exergy and environmental analysis of the vehicle fuel end use is presented. This analysis comprises petroleum and natural gas derivatives (including hydrogen), biofuels (ethanol and biodiesel), and their mixtures, besides of the electricity generated in the Brazilian electricity mix, intended to be used in plug in electric vehicles. The renewable and non-renewable unit exergy costs and CO 2 emission cost are proposed as suitable indicators for assessing the renewable exergy consumption intensity and the environmental impact, and for quantifying the thermodynamic performance of the transportation sector. This allows ranking the energy conversion processes along the vehicle fuels production routes and their end use, so that the best options for the transportation sector can be determined and better energy policies may be issued. It is found that if a drastic CO 2 emissions abatement of the sector is pursued, a more intensive utilization of ethanol in the Brazilian transportation sector mix is advisable. However, as the overall exergy conversion efficiency of the sugar cane industry is still very low, which increases the unit exergy cost of ethanol, better production and end use technologies are required. Nonetheless, with the current scenario of a predominantly renewable Brazilian electricity mix, based on more than 80% of renewable sources, this source consolidates as the most promising energy source to reduce the large amount of greenhouse gas emissions which transportation sector is responsible for

Conventional bio-transportation fuels : an update

OpenAIRE

Uil, den, H.; Bakker, R.R.C.; Deurwaarder, E.P.; Elbersen, H.W.; Weismann, M.

2003-01-01

Up to now renewable energy sources are primarily used in the Netherlands for electricity production. At the end of the past decade the GAVE programme started to facilitate the introduction of gaseous and liquid fuels in the post-Kyoto period (after 2010), with the potential to realize more than 80% CO2 reduction as compared to its fossil alternative. In the first phase of the GAVE programme a large number of options for the production of climate neutral gaseous and liquid fuels were evaluated...

Transportation 2000. Spent fuel transportation trends in the new millenium

International Nuclear Information System (INIS)

Blee, David; Viebrock, James; Patterson, John

1999-01-01

The paper will provide a comparison of foreign research reactor spent fuel transportation today verses the assumptions used by the Department of Energy in the Environmental Impact Statement. In addition, it will suggest changes that are likely to occur in transportation logistics through the remainder of the U.S. spent fuel returns program. Cask availability, certification status, shipment strategy, cost issues, and public acceptance are among the topical areas that will be examined. Transportation requirements will be assessed in light of current participation in the returns program and the tendency for shipment plans to shift toward spent fuel return toward the end of the 13 year period of eligibility. (author)

Effects of fueling profiles on plasma transport

International Nuclear Information System (INIS)

Houlberg, W.A.; Mense, A.T.; Attenberger, S.E.; Milora, S.L.

1977-01-01

The effects of cold particle fueling profiles on particle and energy transport in an ignition sized tokamak plasma are investigated in this study with a one-dimensional, multifluid transport model. A density gradient driven trapped particle microinstability model for plasma transport is used to demonstrate potential effects of fueling profiles on ignition requirements. Important criteria for the development of improved transport models under the conditions of shallow particle fueling profiles are outlined. A discrete pellet fueling model indicates that large fluctuations in density and temperature may occur in the outer regions of the plasma with large, shallowly penetrating pellets, but fluctuations in the pressure profile are small. The hot central core of the plasma remains unaffected by the large fluctuations near the plasma edge

Comparison of the Transportation Risks Resulting from Accidents during the Transportation of the Spent Fuel

International Nuclear Information System (INIS)

Jeong Jong Tae; Cho, Dong Kuen; Choi, Heui Joo; Choi, Jong Won

2007-01-01

The safe, environmentally sound and publicly acceptable disposal of high level wastes and spent fuels is becoming a very important issue. The operational safety assessment of a repository including a transportation safety assessment is a fundamental part in order to achieve this goal. According to the long term management strategy for spent fuels in Korea, they will be transported from the spent fuel pools in each nuclear power plant to the central interim storage facility (CISF) which is to start operation in 2016. Therefore, we have to determine the safe and economical logistics for the transportation of these spent fuels by considering their transportation risks and costs. In this study, we developed four transportation scenarios by considering the type of transportation casks and transport means in order to suggest safe and economical transportation logistics for spent fuels. Also, we estimated and compared the transportation risks resulting from the accidents during the transportation of spent fuels for these four transportation scenarios

Renewable energy in energy efficient, low-pollution systems

Energy Technology Data Exchange (ETDEWEB)

Johansson, Bengt

1997-03-01

Energy use accounts for the dominating fraction of total sulphur dioxide (SO{sub 2}), nitrogen oxide (NO{sub x}), volatile organic compounds (VOCs) and carbon dioxide (CO{sub 2}) emissions. In this thesis, different strategies for reducing these emissions are evaluated, using a bottom-up approach. CO{sub 2} emissions from electricity and heat production in western Scania, Sweden, can be reduced by 25% and the emissions of acidifying gases (SO{sub 2} and NO{sub x}) by 50% by the year 2010, compared with 1988 levels, using energy systems based on efficient end-use technologies, cogeneration of heat and electricity, renewable energy sources and low-pollution energy conversion technologies. Exhaust-pipe NO{sub x} emissions from the Swedish transportation sector can be reduced by 50 percent by the year 2015, compared with 1991, by implementing the best available vehicle technologies. Exhaust-pipe emissions of CO{sub 2} can be stabilized at the 1991 level. With further technical development and the use of fuels from renewable sources of energy, NO{sub x} emissions can be reduced by 75 percent and CO{sub 2} emissions by 80 percent compared with 1991 levels. Swedish biomass resources are large, and, assuming production conditions around 2015, about 200 TWh/year could be utilised for energy. Major reductions in CO{sub 2} emissions could be achieved by substituting biomass for fossil fuels in heat, electricity and transportation fuel production. Transportation fuels produced from cellulosic biomass are likely to be less expensive than transportation fuels from conventional biomass feedstocks such as oil plants, sugar-beet and cereals. 90 refs, 3 figs, 5 tabs

On the causal links between health indicator, output, combustible renewables and waste consumption, rail transport, and CO2 emissions: the case of Tunisia.

Science.gov (United States)

Ben Jebli, Mehdi

2016-08-01

This study employs the autoregressive distributed lag (ARDL) approach and Granger causality test to investigate the short- and long-run relationships between health indicator, real GDP, combustible renewables and waste consumption, rail transport, and carbon dioxide (CO2) emissions for the case of Tunisia, spanning the period of 1990-2011. The empirical findings suggest that the Fisher statistic of the Wald test confirm the existence of a long-run relationship between the variables. Moreover, the long-run estimated elasticities of the ARDL model provide that output and combustible renewables and waste consumption have a positive and statistically significant impact on health situation, while CO2 emissions and rail transport both contribute to the decrease of health indicator. Granger causality results affirm that, in the short-run, there is a unidirectional causality running from real GDP to health, a unidirectional causality from health to combustible renewables and waste consumption, and a unidirectional causality from all variables to CO2 emissions. In the long-run, all the computed error correction terms are significant and confirm the existence of long-run association among the variables. Our recommendations for the Tunisian policymakers are as follows: (i) exploiting wastes and renewable fuels can be a good strategy to eliminate pollution caused by emissions and subsequently improve health quality, (ii) the use of renewable energy as a main source for national rail transport is an effective strategy for public health, (iii) renewable energy investment projects are beneficial plans for the country as this contributes to the growth of its own economy and reduce energy dependence, and (iii) more renewable energy consumption leads not only to decrease pollution but also to stimulate health situation because of the increase of doctors and nurses numbers.

Pyrolysis bio-oil upgrading to renewable fuels.

Science.gov (United States)

2014-01-01

This study aims to upgrade woody biomass pyrolysis bio-oil into transportation fuels by catalytic hydrodeoxygenation : (HDO) using nanospring (NS) supported catalyst via the following research objectives: (1) develop nanospring-based : catalysts (nan...

Calculation of lifecycle greenhouse gas emissions for the renewable fuel standard

Science.gov (United States)

2009-06-25

The Energy Independence and Security Act of 2007 (EISA, P.L. 110-140), significantly expanded the renewable fuel standard (RFS) established in the Energy Policy Act of 2005 (EPAct 2005, P.L.109-58). The RFS requires the use of 9.0 billion gallons of ...

Ethanol as a Fuel for Road Transportation

Energy Technology Data Exchange (ETDEWEB)

Larsen, U.; Johansen, T.; Schramm, J.

2009-05-15

Bioethanol as a motor fuel in the transportation sector, mainly for road transportation, has been subject to many studies and much discussion. Furthermore, the topic involves not only the application and engine technical aspects, but also the understanding of the entire life cycle of the fuel, well-to-wheels, including economical, environmental, and social aspects. It is not, however, the aim of this report to assess every single one of these aspects. The present report aims to address the technical potential and problems as well as the central issues related to the general application of bioethanol as an energy carrier in the near future. A suitable place to start studying a fuel is at the production stage, and bioethanol has been found to have a potential to mitigate greenhouse gases, depending on the production method. This and a potential for replacing fossil fuel-based oil (and being renewable) are the main reasons why ethanol is considered and implemented. Therefore, we must focus on two central questions related to ethanol implementation: how much carbon dioxide (CO2) can be mitigated and how much fossil fuel can be replaced? A number of life cycle assessments have been performed in order to provide estimates. These assessments have generally shown that bioethanol has very good potential and can mitigate CO2 emissions very effectively, but It has also been shown that the potential for both fossil fuel replacement and CO2 mitigation is totally dependent on the method used to produce the fuel. Bioethanol can be made from a wide range of biomass resources, not all equally effective at mitigating CO2 emissions and replacing fossil fuel. The Brazilian ethanol experience has in many ways shown the way for the rest of the world, not least in the production stage. Brazil was the first and biggest producer of bioethanol, but the United States, China, India, and European Union have since then increased their production dramatically. Overall, bioethanol represents the

Conventional bio-transportation fuels : an update

NARCIS (Netherlands)

Uil, den H.; Bakker, R.R.C.; Deurwaarder, E.P.; Elbersen, H.W.; Weismann, M.

2003-01-01

Up to now renewable energy sources are primarily used in the Netherlands for electricity production. At the end of the past decade the GAVE programme started to facilitate the introduction of gaseous and liquid fuels in the post-Kyoto period (after 2010), with the potential to realize more than 80%

Spent fuel and HLW transportation the French experience

International Nuclear Information System (INIS)

Giraud, J.P.; Charles, J.L.

1995-01-01

With 53 nuclear power plants in operation at EDF and a fuel cycle with recycling policy of the valuable materials, COGEMA is faced with the transport of a wide range of radioactive materials. In this framework, the transport activity is a key link in closing the fuel cycle. COGEMA has developed a comprehensive Transport Organization System dealing with all the sectors of the fuel cycle. The paper will describe the status of transportation of spent fuel and HLW in France and the experience gathered. The Transport Organization System clearly defines the role of all actors where COGEMA, acting as the general coordinator, specifies the tasks to be performed and brings technical and commercial support to its various subcontractors: TRANSNUCLEAIRE, specialized in casks engineering and transport operations, supplies packaging and performs transport operations, LEMARECHAL and CELESTIN operate transport by truck in the Vicinity of the nuclear sites while French Railways are in charge of spent fuel transport by train. HLW issued from the French nuclear program is stored for 30 years in an intermediate storage installation located at the La Hague reprocessing plant. Ultimately, these canisters will be transported to the disposal site. COGEMA has set up a comprehensive transport organization covering all operational aspects including adapted procedures, maintenance programs and personnel qualification

Worldwide spent fuel transportation logistics

International Nuclear Information System (INIS)

Best, R.E.; Garrison, R.F.

1978-01-01

This paper presents an overview of the worldwide transportation requirements for spent fuel. Included are estimates of numbers and types of shipments by mode and cask type for 1985 and the year 2000. In addition, projected capital and transportation costs are presented. For the year 1977 and prior years inclusive, there is a cumulative worldwide requirement for approximately 300 MTU of spent fuel storage at away-from-reactor (AFR) facilities. The cumulative requirements for years through 1985 are projected to be nearly 10,000 MTU, and for the years through 2000 the requirements are conservatively expected to exceed 60,000 MTU. These AFR requirements may be related directly to spent fuel transportation requirements. In total nearly 77,000 total cask shipments of spent fuel will be required between 1977 and 2000. These shipments will include truck, rail, and intermodal moves with many ocean and coastal water shipments. A limited number of shipments by air may also occur. The US fraction of these is expected to include 39,000 truck shipments and 14,000 rail shipments. European shipments to regional facilities are expected to be primarily by rail or water mode and are projected to account for 16,000 moves. Pacific basin shipments will account for 4500 moves. The remaining are from other regions. Over 400 casks will be needed to meet the transportation demands. Capital investment is expected to reach $800,000,000 in 1977 dollars. Cumulative transport costs will be a staggering $4.4 billion dollars

Fuel options for public bus fleets in Sweden

OpenAIRE

Xylia, Maria; Silveira, Semida

2015-01-01

The Swedish public transport sector has defined two major targets, i.e., to run 90% of the total vehicle kilometers of the fleet on non-fossil fuels and double the volume of travel via public transport by 2020, increasing the share of public transport in relation to the total personal transport in the country . The f3 report Fuel options for public bus fleets in Sweden highlights the challenges and solutions encountered, particularly when it comes to the adoption of renewable fuels in the reg...

Transport device of spent fuel

International Nuclear Information System (INIS)

Watanabe, Takashi.

1976-01-01

Object: To provide a transport device of spent fuel particularly used in a fast breeder, which can enhance accessibility to travelling mechanism portions and exchangeability thereof to facilitate maintenance in the event of failure. Structure: On a travelling floor, which has a function to shield radioactive rays, extending in a direction of transporting spent fuel and being formed with a break passing through in a direction wall thickness, a travelling body is moved along the break. The travelling body has a support rod member mounted thereon, and the support rod member is moved within the break, the support rod member having a fuel support pocket suspended therefrom. (Furukawa, Y.)

BNFL's new spent fuel transport flask - Excellox 8

International Nuclear Information System (INIS)

McWilliam, D.S.

2002-01-01

Since British Nuclear Fuels plc (BNFL) was formed in 1971 its transport service has safely moved spent light water reactor fuel from many locations abroad to its fuel handling plants at Sellafield in the UK. To support this business a number of types of flasks have been designed and used. One of the types used has been the Excellox family of water-filled flasks. To support future business opportunities a new flask, designed to meet the requirements of the new IAEA transport regulations TS-R-1 (ST-1, Revised), has been developed. The flask will be a type B(U)F. This new flask design will maximise fuel carrying capacity to minimise transport costs. The design capacity of the new Excellox 8 flask is to be 12 pressurised water reactor or 32 boiling water reactor fuel assemblies. The objective of this BNFL project is to provide another economic spent nuclear fuel transport system, in support of BNFL transport business. (author)

Thermo-chemical conversion of biomass for sustainable aviation fuel/fuel additives

OpenAIRE

Subagyono, Dirgarini Julia Nurlianti

2017-01-01

Research in renewable energy is essential because of the limited supply of fossil fuel, particularly liquids, and the problem resulting from emissions of greenhouse gases, NOx and H₂S. For aviation/jet fuel, organic liquids cannot yet be replaced by electricity, solar cells, or gas. Currently, CO₂ emission from aviation fuels appears to be a small problem compared to that from road transport, but CO₂ emissions per passenger from fossil derived aviation fuel is actually higher than that from a...

Optimizing renewable energy, demand response and energy storage to replace conventional fuels in Ontario, Canada

International Nuclear Information System (INIS)

Richardson, David B.; Harvey, L.D. Danny

2015-01-01

Electricity systems with high penetrations of renewable energy require a mix of resources to balance supply with demand, and to maintain safe levels of system reliability. A load balancing methodology is developed to determine the optimal lowest-cost mix of renewable energy resources, demand response, and energy storage to replace conventional fuels in the Province of Ontario, Canada. Three successive cumulative scenarios are considered: the displacement of fossil fuel generation, the planned retirement of an existing nuclear reactor, and the electrification of the passenger vehicle fleet. The results show that each of these scenarios is achievable with energy generation costs that are not out of line with current and projected electricity generation costs. These transitions, especially that which proposes the electrification of the vehicle fleet, require significant investment in new generation, with installed capacities much higher than that of the current system. Transitions to mainly renewable energy systems require changes in our conceptualization of, and approach to, energy system planning. - Highlights: • Model three scenarios to replace conventional fuels with renewables, storage and DR (demand response). • Determine optimal low-cost mix of resources for each scenario. • Scenarios require much higher installed capacities than current system. • Energy transitions require changes in approach to energy system planning.

Hydrogenation and hydrodeoxygenation of biomass-derived oxygenates to liquid alkanes for transportation fuels

Directory of Open Access Journals (Sweden)

Shaohui Sun

2018-04-01

Full Text Available An attractive approach for the production of transportation fuels from renewable biomass resources is to convert oxygenates into alkanes. In this paper, C5–C20 alkanes formed via the hydrogenation and hydrodeoxygenation of the oligomers of furfuryl alcohol(FA can be used as gasoline, diesel and jet fuel fraction. The first step of the process is the oligomers of FA convert into hydrogenated products over Raney Ni catalyst in a batch reactor. The second step of the process converts hydrogenated products to alkanes via hydrodeoxygenation over different bi-functional catalysts include hydrogenation and acidic deoxidization active sites. After this process, the oxygen content decreased from 22.1 wt% in the oligomers of FA to 0.58 wt% in the hydrodeoxygenation products.

Study of the renewable energy potential and development in Alsace

International Nuclear Information System (INIS)

2016-01-01

This report is part of a study which aimed at assessing the possibility of a renewable energy production equal to or greater than Alsace energy production between 2020 and 2050. It comprised an analysis of potentials and deadlocks for the development of each renewable energy. After an overview of renewable energy production by the end of 2012, the report addresses the different sectors (solar, biomass fuel, geothermal, heat recovery, aero-thermal, wind, hydroelectricity, methanization, agricultural fuels, transports). For each of them, it proposes assessments for the different specific technical resources and processes. Then, after a synthesis of the obtained maximum theoretical resources, it reports the development of three scenarios (a trend-based one, a maximum one, and a proactive one) while addressing each resource within them

The feasibility of synthetic fuels in renewable energy systems

DEFF Research Database (Denmark)

Ridjan, Iva; Mathiesen, Brian Vad; Connolly, D.

2013-01-01

, and other impacts on the environment and biosphere. Hence, it is essential to make a detailed analysis of this sector in order to match the demand and to meet the criteria of a 100% renewable energy system in 2050. The purpose of this article is to identify potential pathways for producing synthetic fuels......, with a specific focus on solid oxide electrolyser cells (SOEC) combined with the recycling of CO2....

The feasibility of synthetic fuels in renewable energy systems

DEFF Research Database (Denmark)

Ridjan, Iva; Mathiesen, Brian Vad; Connolly, David

2012-01-01

supplies, and other impacts on environment and biosphere. Hence, it is essential to make a detailed analysis of this sector in order to match the demand and to meet the criteria of a 100% renewable energy system in 2050. The purpose of this article is to identify potential pathways for producing synthetic...... fuels, with a specific focus on solid oxide electrolyser cells combined with the recycling of CO2....

Transportation fuels of the future?

International Nuclear Information System (INIS)

Piel, W.J.

2001-01-01

Society is putting more emphasis on the mobile transportation sector to achieve future goals of sustainability and a cleaner environment. To achieve these goals, does society need to jump to a new combination of fuel and vehicle technology or can we just continue to improve on the current fuels and drive train technology that has powered us the past 70 or more years? Do we need to move to more exotic energy conversion technology (fuel cell vehicles?), or can improving fuel properties further allow us to continue using combustion engines to power our vehicles? What fuel properties can still be improved in gasoline and diesel? Besides removing sulfur, should there be less aromatics in fuels? Should aromatics be eliminated? Is there a role for oxygenates in gasoline and diesel? Do blending oxygenates in fuels help or hinder in achieving the environmental goals? Can we and should we reduce our dependency on crude oil for transportation energy? Why have not the previous government-sponsored Alternative Fuel programs displaced crude oil? The marketplace will determine which fuel and vehicle technology combination will eventually be used in the future. Does the information we know today give us insight to this future? This paper will attempt to address some of the key issues and questions on the role fuels may play in that marketplace decision

Fuels and Combustion | Transportation Research | NREL

Science.gov (United States)

Fuels and Combustion Fuels and Combustion This is the March 2015 issue of the Transportation and , combustion strategy, and engine design hold the potential to maximize vehicle energy efficiency and performance of low-carbon fuels in internal combustion engines with a whole-systems approach to fuel chemistry

Transportation of spent MTR fuels

Energy Technology Data Exchange (ETDEWEB)

Raisonnier, D.

1997-08-01

This paper gives an overview of the various aspects of MTR spent fuel transportation and provides in particular information about the on-going shipment of 4 spent fuel casks to the United States. Transnucleaire is a transport and Engineering Company created in 1963 at the request of the French Atomic Energy Commission. The company followed the growth of the world nuclear industry and has now six subsidiaries and affiliated companies established in countries with major nuclear programs.

Transportation of spent MTR fuels

International Nuclear Information System (INIS)

Raisonnier, D.

1997-01-01

This paper gives an overview of the various aspects of MTR spent fuel transportation and provides in particular information about the on-going shipment of 4 spent fuel casks to the United States. Transnucleaire is a transport and Engineering Company created in 1963 at the request of the French Atomic Energy Commission. The company followed the growth of the world nuclear industry and has now six subsidiaries and affiliated companies established in countries with major nuclear programs

Hydrogen , Hybrid and Electric Propulsion in a Strategy for Sustainable Transport

DEFF Research Database (Denmark)

Jørgensen, Kaj

1998-01-01

Analysis of the scope for application of hydrogen and electric propulsion for improvement of the fuel cycle efficiency and introduction of renewable energy in the transport sector. The paper compares these fuels with each other as well as with other fuels (especially bio fuels) and outlines...... their individual roles in a strategy for sustainable transport. Finally, the fuels are compared to the present fuels....

On the road : non-fossil fuel deployment for the public bus fleet of Sweden

OpenAIRE

Xylia, Maria; Silveira, Semida

2015-01-01

The public transport sector in Sweden has set a target to run 90% of its total vehicle-kilometers on renewable fuels by 2020, and double its market share in the long term. The focus of this paper is the adoption of renewable fuels in public bus fleets. Data for all 21 Swedish counties were gathered and analyzed, mapping the bus fleets’ condition in relation to renewable fuel deployment, CO2 emissions and energy efficiency. The main factors affecting fuel choices in the bus fleets were investi...

Sustainable hydrocarbon fuels by recycling CO2 and H2O with renewable or nuclear energy

DEFF Research Database (Denmark)

Graves, Christopher R.; Ebbesen, Sune; Mogensen, Mogens Bjerg

2011-01-01

) and biofuels have received the most attention, similar hydrocarbons can be produced without using fossil fuels or biomass. Using renewable and/or nuclear energy, carbon dioxide and water can be recycled into liquid hydrocarbon fuels in non-biological processes which remove oxygen from CO2 and H2O (the reverse...... of fuel combustion). Capture of CO2 from the atmosphere would enable a closed-loop carbon-neutral fuel cycle. This article critically reviews the many possible technological pathways for recycling CO2 into fuels using renewable or nuclear energy, considering three stages—CO2 capture, H2O and CO2...... by Fischer–Tropsch synthesis is identified as one of the most promising, feasible routes. An analysis of the energy balance and economics of this CO2 recycling process is presented. We estimate that the full system can feasibly operate at 70% electricity-to-liquid fuel efficiency (higher heating value basis...

Life cycle assessment of renewable energy sources

CERN Document Server

Singh, Anoop; Olsen, Stig Irving

2013-01-01

Governments are setting challenging targets to increase the production of energy and transport fuel from sustainable sources. The emphasis is increasingly on renewable sources including wind, solar, geothermal, biomass based biofuel, photovoltaics or energy recovery from waste. What are the environmental consequences of adopting these other sources? How do these various sources compare to each other? Life Cycle Assessment of Renewable Energy Sources tries to answer these questions based on the universally adopted method of Life Cycle Assessment (LCA). This book introduces the concept and impor

Electrifying Australian transport: Hybrid life cycle analysis of a transition to electric light-duty vehicles and renewable electricity

International Nuclear Information System (INIS)

Wolfram, Paul; Wiedmann, Thomas

2017-01-01

Highlights: •This research assesses life-cycle carbon impacts of different powertrains. •We illustrate a transition to low-carbon vehicles in a hybrid IO-LCA model. •Different electricity and transport scenarios are integrated in the model. •With Australia’s current grid-mix, electric vehicles offer no mitigation potential. •Using renewable energy, electric vehicle carbon footprints can be cut by 66%. -- Abstract: Recent life cycle assessments confirmed the greenhouse gas emission reduction potential of renewable electricity and electric vehicle technologies. However, each technology is usually assessed separately and not within a consistent macro-economic, multi-sectoral framework. Here we present a multi-regional input-output based hybrid approach with integrated scenarios to facilitate the carbon footprint assessment of all direct and indirect effects of a transition to low-emission transportation and electricity generation technologies in Australia. The work takes into account on-road energy consumption values that are more realistic than official drive-cycle energy consumption figures used in previous work. Accounting for these factors as well as for Australia’s grid electricity, which heavily relies on coal power, electric vehicles are found to have a higher carbon footprint than conventional vehicles, whereas hybrid electric vehicles have the lowest. This means that – from a carbon footprint perspective – powertrain electrification is beneficial only to a certain degree at the current stage. This situation can be changed by increasing shares of renewable electricity in the grid. In our best-case scenario, where renewable energy accounts for 96% of the electricity mix in 2050, electric vehicle carbon footprints can be cut by 66% by 2050 relative to 2009. In the business-as-usual scenario (36% renewable electricity share by 2050), electric vehicles can reach a 56% reduction if fossil fuel power plants significantly increase their efficiencies

Hydrogen Fuel Cell Vehicles

OpenAIRE

Anton Francesch, Judit

1992-01-01

Hydrogen is an especially attractive transportation fuel. It is the least polluting fuel available, and can be produced anywhere there is water and a clean source of electricity. A fuel cycle in which hydrogen is produced by solar-electrolysis of water, or by gasification of renewably grown biomass, and then used in a fuel-cell powered electric-motor vehicle (FCEV), would produce little or no local, regional, or global pollution. Hydrogen FCEVs would combine the best features of bat...

Transporting spent nuclear fuel: an overview

International Nuclear Information System (INIS)

1986-03-01

Although high-level radioactive waste from both commercial and defense activities will be shipped to the repository, this booklet focuses on various aspects of transporting commercial spent fuel, which accounts for the majority of the material to be shipped. The booklet is intended to give the reader a basic understanding of the following: the reasons for transportation of spent nuclear fuel, the methods by which it is shipped, the safety and security precautions taken for its transportation, emergency response procedures in the event of an accident, and the DOE program to develop a system uniquely appropriate to NWPA transportation requirements

Renewables in Transport: Directive 2009/28/EC - Devils in its Details

International Nuclear Information System (INIS)

Wilkin, S.

2009-01-01

As part of the 3*20 targets reached in December 2008, the EC decided that the EU should, by 2020, source 20% of its Final Energy Consumption (FEC) renewably. Working towards this aim should in general contribute to the primary objective of reducing emissions, but there are two major issues with the implementation of the target in the Transport sector which run the risk of being irrelevant or even counterproductive. Firstly, the constraining stipulation that all Member States should source 10% of their Transport sector FEC renewably will be a struggle for some Member States to achieve, forcing them to invest large amounts of money which would be better spent elsewhere. Secondly, the relevant legislation gives unrepresentative weight to the benefits of Electric Vehicles (EVs), meaning that Member States which invest in EVs may give the illusion of having reached their national renewable targets without actually having done so. This paper is based on EC Directive 2009/28/EC (henceforth referred to as 'the Directive') and the National Renewable Energy Action Plans of Denmark, France, Germany, Italy, Spain, and the UK which were submitted in response. Each EU Member State has an individual target for the proportion of its FEC which is to come from renewable sources in 2020. The targets are based on the countries? existing renewable shares (as shown in Table 1 below) and their supposed capacity for improvement. Together, they give an average EU-wide target of 20% across the 27 Member States. (author)

Transportation of radioactive wastes from nuclear fuel cycles

International Nuclear Information System (INIS)

1979-09-01

This paper discusses current and foreseen radioactive waste transportation systems as they apply to the INFCE Working Group 7 study. The types of wastes considered include spent fuel, which is treated as a waste in once-through fuel cycles; high-, medium-, and low-level waste; and gaseous waste. Regulatory classification of waste quantities and containers applicable to these classifications are discussed. Radioactive wastes are presently being transported in a safe and satisfactory manner. None of the INFCE candidate fuel cycles pose any extraordinary problems to future radioactive waste transportation and such transportation will not constitute a decisive factor in the choice of a preferred fuel cycle

Effects of Fuel Quantity on Soot Formation Process for Biomass-Based Renewable Diesel Fuel Combustion

KAUST Repository

Jing, Wei

2016-12-01

Soot formation process was investigated for biomass-based renewable diesel fuel, such as biomass to liquid (BTL), and conventional diesel combustion under varied fuel quantities injected into a constant volume combustion chamber. Soot measurement was implemented by two-color pyrometry under quiescent type diesel engine conditions (1000 K and 21% O2 concentration). Different fuel quantities, which correspond to different injection widths from 0.5 ms to 2 ms under constant injection pressure (1000 bar), were used to simulate different loads in engines. For a given fuel, soot temperature and KL factor show a different trend at initial stage for different fuel quantities, where a higher soot temperature can be found in a small fuel quantity case but a higher KL factor is observed in a large fuel quantity case generally. Another difference occurs at the end of combustion due to the termination of fuel injection. Additionally, BTL flame has a lower soot temperature, especially under a larger fuel quantity (2 ms injection width). Meanwhile, average soot level is lower for BTL flame, especially under a lower fuel quantity (0.5 ms injection width). BTL shows an overall low sooting behavior with low soot temperature compared to diesel, however, trade-off between soot level and soot temperature needs to be carefully selected when different loads are used.

The transportation of PuO2 and MOX fuel and management of irradiated MOX fuel

International Nuclear Information System (INIS)

Dyck, H.P.; Rawl, R.; Durpel, L. van den

2000-01-01

Information is given on the transportation of PuO 2 and mixed-oxide (MOX) fuel, the regulatory requirements for transportation, the packages used and the security provisions for transports. The experience with and management of irradiated MOX fuel and the reprocessing of MOX fuel are described. Information on the amount of MOX fuel irradiated is provided. (author)

Dual fuel mode operation in diesel engines using renewable fuels: Rubber seed oil and coir-pith producer gas

Energy Technology Data Exchange (ETDEWEB)

Ramadhas, A.S.; Jayaraj, S.; Muraleedharan, C. [Department of Mechanical Engineering, National Institute of Technology Calicut, Calicut-673601 (India)

2008-09-15

Partial combustion of biomass in the gasifier generates producer gas that can be used as supplementary or sole fuel for internal combustion engines. Dual fuel mode operation using coir-pith derived producer gas and rubber seed oil as pilot fuel was analyzed for various producer gas-air flow ratios and at different load conditions. The engine is experimentally optimized with respect to maximum pilot fuel savings in the dual fuel mode operation. The performance and emission characteristics of the dual fuel engine are compared with that of diesel engine at different load conditions. Specific energy consumption in the dual-fuel mode of operation with oil-coir-pith operation is found to be in the higher side at all load conditions. Exhaust emission was found to be higher in the case of dual fuel mode of operation as compared to neat diesel/oil operation. Engine performance characteristics are inferior in fully renewable fueled engine operation but it suitable for stationary engine application, particularly power generation. (author)

Comparison of the transportation risks for the spent fuel in Korea for different transportation scenarios

International Nuclear Information System (INIS)

Jeong, Jongtae; Cho, D.K.; Choi, H.J.; Choi, J.W.

2011-01-01

According to the long term management strategy for spent fuels in Korea, they will be transported from the spent fuel pools in each nuclear power plant to the central interim storage facility (CISF) which is to start operation in 2016. At the start of the operation of the final repository (FR), by the year 2065, transport will then take place between the CISF and the FR. Therefore, we have to determine the safe and economical logistics for the transportation of these spent fuels by considering their transportation risks and costs. In this study, we developed four transportation scenarios for a maritime transportation by considering the type of transportation casks and transport means in order to suggest safe and economical transportation logistics for the spent fuels in Korea. And, we estimated and compared the transportation risks for these four transportation scenarios. Also, we estimated and compared the transportation risks resulting from accidents during the transportation of PWR and PHWR spent fuels by road trailers from the CISF and the FR. From the results of this study, we found that risks resulting from accidents during the transportation of the spent fuels have a very low radiological risk activity with a manageable safety and health consequences. The results of this study can be used as basic data for the development of safe and economical logistics for a transportation of the spent fuels in Korea by considering the transportation costs for the four scenarios which will be needed in the near future.

Lifecycle analysis of renewable natural gas and hydrocarbon fuels from wastewater treatment plants’ sludge

Energy Technology Data Exchange (ETDEWEB)

Lee, Uisung [Argonne National Lab. (ANL), Argonne, IL (United States); Han, Jeongwoo [Argonne National Lab. (ANL), Argonne, IL (United States); Urgun Demirtas, Meltem [Argonne National Lab. (ANL), Argonne, IL (United States); Wang, Michael [Argonne National Lab. (ANL), Argonne, IL (United States); Tao, Ling [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2016-09-01

Wastewater treatment plants (WWTPs) produce sludge as a byproduct when they treat wastewater. In the United States, over 8 million dry tons of sludge are produced annually just from publicly owned WWTPs. Sludge is commonly treated in anaerobic digesters, which generate biogas; the biogas is then largely flared to reduce emissions of methane, a potent greenhouse gas. Because sludge is quite homogeneous and has a high energy content, it is a good potential feedstock for other conversion processes that make biofuels, bioproducts, and power. For example, biogas from anaerobic digesters can be used to generate renewable natural gas (RNG), which can be further processed to produce compressed natural gas (CNG) and liquefied natural gas (LNG). Sludge can be directly converted into hydrocarbon liquid fuels via thermochemical processes such as hydrothermal liquefaction (HTL). Currently, the environmental impacts of converting sludge into energy are largely unknown, and only a few studies have focused on the environmental impacts of RNG produced from existing anaerobic digesters. As biofuels from sludge generate high interest, however, existing anaerobic digesters could be upgraded to technology with more economic potential and more environmental benefits. The environmental impacts of using a different anaerobic digestion (AD) technology to convert sludge into energy have yet to be analyzed. In addition, no studies are available about the direct conversion of sludge into liquid fuels. In order to estimate the energy consumption and greenhouse gas (GHG) emissions impacts of these alternative pathways (sludge-to-RNG and sludge-to-liquid), this study performed a lifecycle analysis (LCA) using the Greenhouse gases, Regulated Emissions, and Energy use in Transportation (GREET®) model. The energy uses and GHG emissions associated with the RNG and hydrocarbon liquid are analyzed relative to the current typical sludge management case, which consists of a single-stage mesophilic

Fuel Cell Demonstration Project - 200 kW - Phosphoric Acid Fuel Cell Power Plant Located at the National Transportation Research Center: FINAL REPORT

Energy Technology Data Exchange (ETDEWEB)

Berry, JB

2005-05-06

Oak Ridge National Laboratory (ORNL) researches and develops distributed generation technology for the Department of Energy, Energy Efficiency and Renewable Energy Distributed Energy Program. This report describes installation and operation of one such distributed generation system, a United Technology Corporation fuel cell located at the National Transportation Research Center in Knoxville, Tennessee. Data collected from June 2003 to June of 2004, provides valuable insight regarding fuel cell-grid compatibility and the cost-benefit of the fuel cell operation. The NTRC fuel cell included a high-heat recovery option so that use of thermal energy improves project economics and improves system efficiency to 59% year round. During the year the fuel cell supplied a total of 834MWh to the NTRC and provided 300MBtu of hot water. Installation of the NTRC fuel cell was funded by the Distributed Energy Program with partial funding from the Department of Defense's Climate Change Fuel Cell Buy Down Program, administered by the National Energy Technology Laboratory. On-going operational expenses are funded by ORNL's utility budget and are paid from operational cost savings. Technical information and the benefit-cost of the fuel cell are both evaluated in this report and sister reports.

Algae as a Feedstock for Transportation Fuels. The Future of Biofuels?

Energy Technology Data Exchange (ETDEWEB)

McGill, Ralph [Sentech, Inc., Fuels, Engines, and Emissions Consulting, Knoxville, TN (United States)

2008-05-15

Events in world energy markets over the past several years have prompted many new technical developments as well as political support for alternative transportation fuels, especially those that are renewable. We have seen dramatic rises in the demand for and production of fuel ethanol from sugar cane and corn and biodiesel from vegetable oils. The quantities of these fuels being used continue to rise dramatically, and their use is helping to create a political climate for doing even more. But, the quantities are still far too small to stem the tide of rising crude prices worldwide. In fact, the use of some traditional crops (corn, sugar, soy, etc.) in making fuels instead of food is apparently beginning to impact the cost of food worldwide. Thus, there is considerable interest in developing alternative biofuel feedstocks for use in making fuels -- feedstocks that are not used in the food industries. Of course, we know that there is a lot of work in developing cellulosic-based ethanol that would be made from woody biomass. Process development is the critical path for this option, and the breakthrough in reducing the cost of the process has been elusive thus far. Making biodiesel from vegetable oils is a well-developed and inexpensive process, but to date there have been few reasonable alternatives for making biodiesel, although advanced processes such as gasification of biomass remain an option.

Transport of encapsulated nuclear fuels

International Nuclear Information System (INIS)

Broman, Ulrika; Dybeck, Peter; Ekendahl, Ann-Mari

2005-12-01

The transport system for encapsulated fuel is described, including a preliminary drawing of a transport container. In the report, the encapsulation plant is assumed to be located to Oskarshamn, and the repository to Oskarshamn or Forsmark

Transportation of irradiated fuel elements

International Nuclear Information System (INIS)

Preece, A.H.

1980-01-01

The report falls under the headings: introduction (explaining the special interest of the London Borough of Brent, as forming part of the route for transportation of irradiated fuel elements); nuclear power (with special reference to transport of spent fuel and radioactive wastes); the flask aspect (design, safety regulations, criticisms, tests, etc.); the accident aspect (working manual for rail staff, train formation, responsibility, postulated accident situations); the emergency arrangements aspect; the monitoring aspect (health and safety reports); legislation; contingency plans; radiation - relevant background information. (U.K.)

An improved assembly for the transport of fuel elements

International Nuclear Information System (INIS)

Myers, G.

1979-01-01

An improved assembly for the transport and storage of radioactive nuclear fuel elements is described. The fuel element transport canister is of the type in which the fuel elements are submerged in liquid with a self regulating ullage system, so that the fuel elements are always submerged in the liquid even when the assembly is used in one orientation during loading and another orientation during transportation. (UK)

Hydrogen fuel cell vehicles for the 3rd millenniums

International Nuclear Information System (INIS)

Fahmy, F.H.

2006-01-01

As the world population increases, so does the demand for transportation. Automobiles, being the most common means of transportation are on of the main sources pollution. Therefore, in order to meet the needs of society and to protect the environment, scientists began looking for a new solution to this problem. Before they suggested any answers, the scientists first looked at all aspects surrounding the issue. Fuel cell can be promoted energy diversity and a transition to renewable energy sources. This paper presents a new friendly environmental vehicles. The fuel of this vehicles is a renewable sources, solar radiation, PV arrays, electrolyzer, hydrogen and fuel cell. All the results show the capability of vehicle's design with all the details of each main component for several varieties of vehicles for transportation. This new idea realizes clean and healthy environment vehicles

Alternatives to traditional transportation fuels 1995

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-12-01

This report provides information on transportation fuels other than gasoline and diesel, and the vehicles that use these fuels. The Energy Information Administration (EIA) provides this information to support the U.S. Department of Energy`s reporting obligations under Section 503 of the Energy Policy Act of 1992 (EPACT). The principal information contained in this report includes historical and year-ahead estimates of the following: (1) the number and type of alterative-fueled vehicles (AFV`s) in use; (2) the consumption of alternative transportation fuels and {open_quotes}replacement fuels{close_quotes}; and (3) the number and type of alterative-fueled vehicles made available in the current and following years. In addition, the report contains some material on special topics. The appendices include a discussion of the methodology used to develop the estimates (Appendix A), a map defining geographic regions used, and a list of AFV suppliers.

Control system of fuel transporting device

International Nuclear Information System (INIS)

Yokota, Minoru.

1981-01-01

Purpose: To effectively avoid an obstacle in a fuel transporting device by reading the outputs of absolute position detectors mounted on movable trucks, controlling the movements of the trucks, and thereby smoothly and accurately positioning the fuel transporting device at predetermined position and providing a contact detector thereat. Method: The outputs from absolute position detectors which are mounted on a longitudinally movable truck and a laterally movable truck are input to an input/output control circuit. The input/output control circuit serves to compare, the position a fuel transporting device is to be moved to, with the present position on the basis of said input detection signal and a command signal from an operator console, to calculate the amount of movement to be driven, to produce an operation signal therefor to a control panel, and to drive and control the drive motors which are respectively mounted on the trucks for the fuel transfer device. On the other hand, in case that the transfer device comes into contact with an obstacle, the contact detector will immediately operate to produce a stop command through the control panel to the transporting device, and avoid a collision with the obstacle. (Yoshino, Y.)

Liquid-fueled SOFC power sources for transportation

Science.gov (United States)

Myles, K. M.; Doshi, R.; Kumar, R.; Krumpelt, M.

Traditionally, fuel cells have been developed for space or stationary terrestrial applications. As the first commercial 200-kW systems were being introduced by ONSI and Fuji Electric, the potentially much larger, but also more challenging, application in transportation was beginning to be addressed. As a result, fuel cell-powered buses have been designed and built, and R&D programs for fuel cell-powered passenger cars have been initiated. The engineering challenge of eventually replacing the internal combustion engine in buses, trucks, and passenger cars with fuel cell systems is to achieve much higher power densities and much lower costs than obtainable in systems designed for stationary applications. At present, the leading fuel cell candidate for transportation applications is, without question, the polymer electrolyte fuel cell (PEFC). Offering ambient temperature start-up and the potential for a relatively high power density, the polymer technology has attracted the interest of automotive manufacturers worldwide. But the difficulties of fuel handling for the PEFC have led to a growing interest in exploring the prospects for solid oxide fuel cells (SOFCs) operating on liquid fuels for transportation applications. Solid oxide fuel cells are much more compatible with liquid fuels (methanol or other hydrocarbons) and are potentially capable of power densities high enough for vehicular use. Two SOFC options for such use are discussed in this report.

Contributions to LWR spent fuel storage and transport

International Nuclear Information System (INIS)

The papers included in this document describe the aspects of spent LWR fuel storage and transport-behaviour of spent fuel during storage; use of compact storage packs; safety of storage; design of storage facilities AR and AFR; description of transport casks and transport procedures

Inventory of concepts for mixed diesel fuels containing renewable components. Final report

Energy Technology Data Exchange (ETDEWEB)

Kronberg, B. [Inst. for Surface Chemistry, Stockholm (Sweden); Berg, R. [Befri Konsult, Solna (Sweden); Berg, J. [Svenska Lantmaennen/Agro Oil, Stockholm (Sweden)

2000-08-01

The present report has involved the assembly of two sub-reports, which have been put together to form this final report. Both of the sub-reports deal with the incorporation of ethanol in diesel fuels. The potential advantages are the decreased net emissions of carbon dioxide, due to the renewable nature of ethanol (if obtained from renewable raw materials), and the decrease of NO{sub x} emissions, due to the decreased combustion temperature. The first sub-report is a compilation of scientific articles and patents/patent applications regarding the possibility to blend ethanol into diesel to form a stable solution in the form of a so called microemulsion, with the aid of surfactants and/or co-solvents. The second sub-report briefly describes the test work, both in the laboratory and in field tests, that is being done in various countries, regarding the blending of ethanol into diesel fuel.

Promoting biogas production and using it as transport fuel in the Helsinki region; Suunnitelma liikennebiokaasun tuotannon ja kaeytoen edistaemiseksi Helsingin seudulla

Energy Technology Data Exchange (ETDEWEB)

Rasi, S.; Havukainen, J.; Uusitalo, V.; Andersson, R.; Manninen, K.; Aro-Heinilae, E.; Rintala, J.

2012-11-01

The main objective of the project was to promote biogas production and its use as transport fuel. The aims in the four Finnish and two Estonian case areas were to reduce the amount and improve the sustainable use of waste and sludge, to promote biogas production, to start biogas use as transport fuel and to provide tools for implementing the aims. The total biomethane potential in the Helsinki region corresponds to approximately 450 GWh/a. The most potential user for biomethane is public transport. The total amount of biomethane would suffice for 80% of the busses operating in the Helsinki region. Using biogas as a transport fuel instead of energy production in the Helsinki region would result in emission reductions (13 000 t{sub CO2,eq}/a). However if the fuel replacing biogas in energy production would be renewable, the emission reductions would be significantly greater. The economical assessment indicates that the production of biogas is economically feasible if all the produced gas can be sold. Biogas produced near the natural gas grid can also be transported to the Helsinki region where there are better possibilities to find uses for it. In this way, for example, gas that is produced in Kymenlaakso but is not consumed there can be transported via the natural gas grid, assuming that the production plant is reasonably close to the grid. (orig.)

Motor Fuel Excise Taxes

Energy Technology Data Exchange (ETDEWEB)

2015-09-01

A new report from the National Renewable Energy Laboratory (NREL) explores the role of alternative fuels and energy efficient vehicles in motor fuel taxes. Throughout the United States, it is common practice for federal, state, and local governments to tax motor fuels on a per gallon basis to fund construction and maintenance of our transportation infrastructure. In recent years, however, expenses have outpaced revenues creating substantial funding shortfalls that have required supplemental funding sources. While rising infrastructure costs and the decreasing purchasing power of the gas tax are significant factors contributing to the shortfall, the increased use of alternative fuels and more stringent fuel economy standards are also exacerbating revenue shortfalls. The current dynamic places vehicle efficiency and petroleum use reduction polices at direct odds with policies promoting robust transportation infrastructure. Understanding the energy, transportation, and environmental tradeoffs of motor fuel tax policies can be complicated, but recent experiences at the state level are helping policymakers align their energy and environmental priorities with highway funding requirements.

Ordinance concerning the filing of transport of nuclear fuel materials

International Nuclear Information System (INIS)

1987-01-01

This Order provides provisions concerning nuclear fuel substances requiring notification (nuclear fuel substance, material contaminated with nuclear fuel substances, fissionable substances, etc.), procedure for notification (to prefectural public safety commission), certificate of transpot (issued via public safety commission), instructions (speed of vehicle for transporting nuclear fuel substances, parking of vehicle, place for loading and unloading of nuclear fuel substances, method for loading and unloading, report to police, measures for disaster prevention during transport, etc.), communication among members of public safety commission (for smooth transport), notification of alteration of data in transport certificate (application to be submitted to public safety commission), application of reissue of transport certificate, return of transport certificate, inspection concerning transport (to be performed by police), submission of report (to be submitted by refining facilities manager, processing facilities manager, nuclear reactor manager, master of foreign nuclear powered ship, reprocessing facilities manager, waste disposal facilities manager; concerning stolen or missing nuclear fuel substances, traffic accident, unusual leakage of nuclear fuel substances, etc.). (Nogami, K.)

Nuclear-electrolytic hydrogen as a transportation fuel

International Nuclear Information System (INIS)

DeLuchi, M.A.

1989-01-01

Hydrogen is a very attractive transportation fuel in three important ways: it is the least polluting fuel that can be used in an internal combustion engine, it produces no greenhouse gases, and it is potentially available anywhere there is water and a clean source of power. The prospect of a clean, widely available transportation fuel has motivated much of the research on hydrogen fuels. This paper is a state-of-the art review of the production, storage, performance, environmental impacts, safety, and cost of nuclear-electrolytic hydrogen for highway vehicles

EDF energy generation UK transport of irradiated fuel

Energy Technology Data Exchange (ETDEWEB)

James, R. [EDF Energy, London, (United Kingdom)

2015-07-01

This paper give an overview of irradiated fuel transport in the UK. It describes the design of irradiated fuel flask used by EDF Energy; operational experience and good practices learnt from over 50 years of irradiated fuel transport. The AGRs can store approximately 9 months generation of spent fuel, hence the ability to transport irradiated fuel is vital. Movements are by road to the nearest railhead, typically less than 2 miles and then by rail to Sellafield, up to 400 miles, for reprocessing or long term storage. Road and rail vehicles are covered. To date in the UK: over 30,000 Magnox flask journeys and over 15,000 AGR A2 flask journeys have been carried out.

Thermal model of spent fuel transport cask

International Nuclear Information System (INIS)

Ahmed, E.E.M.; Rahman, F.A.; Sultan, G.F.; Khalil, E.E.

1996-01-01

The investigation provides a theoretical model to represent the thermal behaviour of the spent fuel elements when transported in a dry shipping cask under normal transport conditions. The heat transfer process in the spent fuel elements and within the cask are modeled which include the radiant heat transfer within the cask and the heat transfer by thermal conduction within the spent fuel element. The model considers the net radiant method for radiant heat transfer process from the inner most heated element to the surrounding spent elements. The heat conduction through fuel interior, fuel-clad interface and on clad surface are also presented. (author) 6 figs., 9 refs

Comparison of renewable fuels based on their land use using energy densities

NARCIS (Netherlands)

Dijkman, T. J.; Benders, R. M. J.

2010-01-01

In this article energy densities of selected renewable fuels are determined. Energy density is defined here as the annual energy production per hectare, taking energy inputs into account. Using 5 scenarios, consisting of 1 set focusing on technical differences and 1 set focusing on geographical

Transporting fuel debris from TMI-2 to INEL

International Nuclear Information System (INIS)

Quinn, G.J.; Burton, H.M.; Bixby, W.W.; McIntosh, T.W.; McGoff, O.J.; Barkonic, R.J.; Henrie, J.O.

1986-06-01

Transportation of the damaged fuel from Unit 2 of Three Mile Island (TMI-2) presented noteworthy technical challenges involving complex institutional issues. The program resulted from both a need to package and remove the accident debris and also the opportunity to receive and study damaged core components. These combined to establish the safe transport of the TMI-2 fuel debris as a high priority for many diverse organizations. The capability of the sending and receiving facilities to handle spent fuel transport casks in the most cost-effective manner was assessed and resulted in the development by Nuclear Packaging Inc. (NuPac) of the NuPac 125-B rail cask. This paper reviews the technical challenges in preparation of the TMI-2 core debris for transport from TMI-2 to the Idaho National Engineering Laboratory (INEL) and receipt and storage of that material at INEL. Challenges discussed include design and testing of fuel debris canisters; design, fabrication and licensing of a new rail cask for spent fuel transport; cask loading operations, equipment and facilities at TMI-2; transportation logistics; and, receipt, storage and core examination operations at INEL. 10 refs

Effects of fueling profiles on plasma transport

International Nuclear Information System (INIS)

Mense, A.T.; Houlberg, W.A.; Attenberger, S.E.; Milora, S.L.

1978-04-01

A one-dimensional (1-D), multifluid transport model is used to investigate the effects of particle fueling profiles on plasma transport in an ignition-sized tokamak (TNS). Normal diffusive properties of plasmas will likely maintain the density at the center of the discharge even if no active fueling is provided there. This significantly relaxes the requirements for fuel penetration. Not only is lower fuel penetration easier to achieve, but it may have the advantage of reducing or eliminating density gradient-driven trapped particle microinstabilities. Simulation of discrete pellet fueling indicates that relatively low velocity (approximately 10 3 m/sec) pellets may be sufficient to fuel a TNS-sized device (approximately 1.25-m minor radius), to produce a relatively broad, cool edge region of plasma which should reduce the potential for sputtering, and also to reduce the likelihood of trapped particle mode dominated transport. Low penetrating pellets containing up to 10 to 20 percent of the total plasma ions can produce fluctuations in density and temperature at the plasma edge, but the pressure profile and fusion alpha production remain almost constant

Alternative transport fuels: supply, consumption and conservation

International Nuclear Information System (INIS)

Trindade, S.C.

1990-01-01

Road-based passenger and freight transport almost exclusively uses petroleum/hydrocarbon fuels in the fluid form. These fuels will probably continue to be major transport fuels well into the 21st century. As such there is need to prolong their use which can be done through: (1) conservation of fuel by increasing efficiency of internal combustion engines, and (2) conversion of natural gas, coal and peat, and biomass into alternate fuels such as ethanol, methanol, CNG, LNG, LPG, low heat-content (producer) gas and vegetable oils. Research, development and demonstration (RD and D) priorities in supply, consumption and conservation of these alternate fuels are identified and ranked in the context of situation prevailing in Brazil. Author has assigned the highest priority for research in the impact of pricing, economic, fiscal and trade policies, capital allocation criteria and institutional and legislative framework. It has also been emphasised that an integrated or systems approach is mandatory to achieve net energy gains in transport sector. (M.G.B.). 33 refs., 11 tabs., 4 figs

A Transition Strategy from Fossil Fuels to Renewable Energy Sources in the Mexican Electricity System

Directory of Open Access Journals (Sweden)

Juan J. Vidal-Amaro

2018-03-01

Full Text Available Renewable energy sources exploitation acquires special importance for creating low-carbon energy systems. In Mexico a national regulation limits the fossil fuel-based electricity generation to 65%, 60% and 50% by years 2024, 2030 and 2050 respectively. This study evaluates several scenarios of renewables incorporation into the Mexican electricity system to attend those targets as well as a 75% renewables-based electricity share target towards a 100% renewable system. By its size, the Mexican electricity system, with a generation of 260.4 TWh/year (85% based on fossil fuels, can be regarded as an illustrating reference. The impact of increasing amounts of wind, photovoltaic solar, biomass, biogas, geothermal, hydro and concentrating solar power on the system’s capacity to attend demand on a one-hour timescale resolution is investigated utilizing the EnergyPLAN model and the minimum total mix capacity method. Possible excess of electricity production is also assessed. For every target year, a solution is obtained corresponding to the combination resulting in the minimum total generation capacity for the electricity system. A transition strategy to a system with a high share of renewables-based electricity is designed where every transition step corresponds to the optimal energy mix for each of the target years.

Risk assessment in spent fuel storage and transportation

International Nuclear Information System (INIS)

Pandimani, S.

1989-01-01

Risk assessment in various stages of nuclear fuel cycle is still an active area of Nuclear safety studies. From the results of risk assessment available in literature, it can be determined that the risk resulting from shipments of plutonium and spent-fuel are much greater than that resulting from the transport of other materials within the nuclear fuel cycle. In India spent fuels are kept in Spent Fuel Storage Pool (SFSP) for about 240-400 days, which is relatively a longer period compared to the usual 120 days as recommended by regulatory authorities. After cooling spent fuels are transported to the reprocessing sites which are mostly situated close to the plants. India has two high level waste treatment facilities, one PREFRE (Plutonium Reprocessing and Fuel Recycling) at Tarapur and the other one, a unit of Nuclear Fuel Complex at Hyderabad. This paper presents the risk associated with spent fuel storage and transportation for the Indian conditions. All calculations are based on a typical CANDU reactor system. Simple fault tree models are evolved for SFSP and for Transportation Accident Mode (TAM) for both road and rail. Fault tree quantification and risk assessment are done to each of these models. All necessary data for SFSP are taken mostly from Reactor Safety Study, (1975). Similarly, the data for rail TAM are taken from Annual Statistical Statements, (1987-8) and that for road TAM from Special Issue on Motor Vehicle Accident Statistics in India, (1986). Simulation method is used wherever necessary. Risk is also estimated for normal/accident free transport

Nanofluidic fuel cell

Science.gov (United States)

Lee, Jin Wook; Kjeang, Erik

2013-11-01

Fuel cells are gaining momentum as a critical component in the renewable energy mix for stationary, transportation, and portable power applications. State-of-the-art fuel cell technology benefits greatly from nanotechnology applied to nanostructured membranes, catalysts, and electrodes. However, the potential of utilizing nanofluidics for fuel cells has not yet been explored, despite the significant opportunity of harnessing rapid nanoscale reactant transport in close proximity to the reactive sites. In the present article, a nanofluidic fuel cell that utilizes fluid flow through nanoporous media is conceptualized and demonstrated for the first time. This transformative concept captures the advantages of recently developed membraneless and catalyst-free fuel cell architectures paired with the enhanced interfacial contact area enabled by nanofluidics. When compared to previously reported microfluidic fuel cells, the prototype nanofluidic fuel cell demonstrates increased surface area, reduced activation overpotential, superior kinetic characteristics, and moderately enhanced fuel cell performance in the high cell voltage regime with up to 14% higher power density. However, the expected mass transport benefits in the high current density regime were constrained by high ohmic cell resistance, which could likely be resolved through future optimization studies.

French experience in research reactor fuel transportation

International Nuclear Information System (INIS)

Raisonnier, Daniele

1996-01-01

Since 1963 Transnucleaire has safely performed a large number of national and international transports of radioactive material. Transnucleaire has also designed and supplied suitable packaging for all types of nuclear fuel cycle radioactive material from front-end and back-end products and for power or for research reactors. Transportation of spent fuel from power reactors are made on a regular and industrial basis, but this is not yet the case for the transport of spent fuel coming from research reactors. Each shipment is a permanent challenge and requires a reactive organization dealing with all the transportation issues. This presentation will explain the choices made by Transnucleaire and its associates to provide and optimize the corresponding services while remaining in full compliance with the applicable regulations and customer requirements. (author)

Texas transportation planning for future renewable energy projects : final report.

Science.gov (United States)

2017-03-01

There will be a significant increase in the number of renewable energy production facilities in Texas. The : construction of wind farms requires the transport of wind turbine components that create increased loads on : rural roads and bridges. These ...

Irradiated nuclear fuel transport from Japan to Europe

International Nuclear Information System (INIS)

Kavanagh, M.T.; Shimoyama, S.

1976-01-01

Irradiated nuclear fuel has been transported from Japan to Europe since 1969, although U.K. experience goes back almost two decades. Both magnox and oxide fuel have been transported, and the technical requirements associated with each type of fuel are outlined. The specialized ships used by British Nuclear Fuels Limited (BNFL) for this transport are described, as well as the ships being developed for future use in the Japan trade. The ship requirements are related to the regulatory position both in the United Kingdom and internationally, and the Japanese regulatory requirements are described. Finally, specific operational experience of a Japanese reactor operator is described

Spent fuels transportation coming from Australia; Transport de combustible use en provenance d'Australie

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-07-01

Maritime transportation of spent fuels from Australia to France fits into the contract between COGEMA and ANSTO, signed in 1999. This document proposes nine information cards in this domain: HIFAR a key tool of the nuclear, scientific and technological australian program; a presentation of the ANSTO Australian Nuclear Science and Technology Organization; the HIFAR spent fuel management problem; the COGEMA expertise in favor of the research reactor spent fuel; the spent fuel reprocessing at La Hague; the transports management; the transport safety (2 cards); the regulatory framework of the transports. (A.L.B.)

Final report : Alberta renewable diesel demonstration

Energy Technology Data Exchange (ETDEWEB)

NONE

2009-02-15

The Alberta renewable diesel demonstration (ARDD) was a demonstration project aimed at providing information and operating experience to stakeholders in the diesel fuel industry. The demonstration took renewable diesel from the lab to the road, providing hands-on experience at 2 and 5 per cent blends (B2 in winter and B5 in shoulder and summer seasons). The ARDD fleet consisted of 59 vehicles running on two types of renewable diesel, notably fatty acid methyl ester (FAME) and hydrogenated-derived renewable diesel (HDRD). This report was a summary of the observations of the ARDD. The report provided a general account of the project scope, methods and observations employed in a multi-stakeholder, real-world demonstration of low-level renewable diesel fuels in challenging winter conditions. The purpose of the report was to provide feedback to stakeholders regarding the use of renewable diesel fuels in Canada's on-road diesel fuel market and to confirm the operability of low level renewable diesel blends under the specific conditions tested ensuring full and continuous compliance with CAN/CGSB 3.520. The report discussed Canada's fuel distribution system in western Canada; the blending facility; blending techniques; fuel retail locations; fuel properties; fuel handling; fuel selection; and fuel testing. It was concluded that the ARDD demonstrated that B2 blends of canola methyl ester and 2 per cent blends of hydrogenation derived renewable diesel were fully operable in winter conditions in the study area when cloud points were adjusted to meet CAN/CGSB requirements. 4 refs., 15 tabs., 20 figs., 2 appendices.

Renewable sustainable biocatalyzed electricity production in a photosynthetic algal microbial fuel cell (PAMFC).

Science.gov (United States)

Strik, David P B T B; Terlouw, Hilde; Hamelers, Hubertus V M; Buisman, Cees J N

2008-12-01

Electricity production via solar energy capturing by living higher plants and microalgae in combination with microbial fuel cells are attractive because these systems promise to generate useful energy in a renewable, sustainable, and efficient manner. This study describes the proof of principle of a photosynthetic algal microbial fuel cell (PAMFC) based on naturally selected algae and electrochemically active microorganisms in an open system and without addition of instable or toxic mediators. The developed solar-powered PAMFC produced continuously over 100 days renewable biocatalyzed electricity. The sustainable performance of the PAMFC resulted in a maximum current density of 539 mA/m2 projected anode surface area and a maximum power production of 110 mW/m2 surface area photobioreactor. The energy recovery of the PAMFC can be increased by optimization of the photobioreactor, by reducing the competition from non-electrochemically active microorganisms, by increasing the electrode surface and establishment of a further-enriched biofilm. Since the objective is to produce net renewable energy with algae, future research should also focus on the development of low energy input PAMFCs. This is because current algae production systems have energy inputs similar to the energy present in the outcoming valuable products.

Waste cooking oil as source for renewable fuel in Romania

Science.gov (United States)

Allah, F. Um Min; Alexandru, G.

2016-08-01

Biodiesel is non-toxic renewable fuel which has the potential to replace diesel fuel with little or no modifications in diesel engine. Waste cooking oil can be used as source to produce biodiesel. It has environmental and economic advantages over other alternative fuels. Biodiesel production from transesterification is affected by water content, type f alcohol, catalyst type and concentration, alcohol to oil ratio, temperature, reaction rate, pH, free fatty acid (FFA) and stirrer speed. These parameters and their effect on transesterification are discussed in this paper. Properties of biodiesel obtained from waste cooking oil are measured according to local standards by distributor and their comparison with European biodiesel standard is also given in this paper. Comparison has shown that these properties lie within the limits of the EN 14214 standard. Furthermore emission performance of diesel engine for biodiesel-diesel blends has resulted in reduction of greenhouse gas emissions. Romanian fuel market can ensure energy security by mixing fuel share with biodiesel produced from waste cooking oil. Life cycle assessment of biodiesel produced from waste cooking oil has shown its viability economically and environmentally.

Summary of the transportation of spent fuel attitude survey

International Nuclear Information System (INIS)

Roop, E.; Price, D.L.; Paquet, V.L.

1992-01-01

The proposed repository at Yucca Mountain, Nevada will increase highway and railway transportation of spent fuel and high level nuclear wastes. The purpose of the survey was to determine the attitudes and differences in attitudes of important actors in the transportation of spent fuel. The three major areas of investigation were 1) perceived risks associated with the transportation of spent fuel, 2) confidence in the government and others responsible for transporting spent fuel, and 3) certain transportation requirements. Response was 34.3% of the original mailing and included: 193 safety personnel, 141 employees of the nuclear industry, 260 government employees, 34 native Americans, and 9 employees of environmental organizations. This paper summarizes overall and group attitudes and opinions for the three areas mentioned above. (author)

Development of nuclear spent fuel Maritime transportation scenario

International Nuclear Information System (INIS)

Yoo, Min; Kang, Hyun Gook

2014-01-01

Spent fuel transportation of South Korea is to be conducted through near sea because it is able to ship a large amount of the spent fuel far from the public comparing to overland transportation. The maritime transportation is expected to be increased and its risk has to be assessed. For the risk assessment, this study utilizes the probabilistic safety assessment (PSA) method and the notions of the combined event. Risk assessment of maritime transportation of spent fuel is not well developed in comparison with overland transportation. For the assessment, first, the transportation scenario should be developed and categorized. Categories are assorted into the locations, release aspects and exposure aspects. This study deals with accident that happens on voyage and concentrated on ship-ship collision. The collision accident scenario is generated with event tree analysis. The scenario will be exploited for the maritime transportation risk model which includes consequence and accident probability

Development of nuclear spent fuel Maritime transportation scenario

Energy Technology Data Exchange (ETDEWEB)

Yoo, Min; Kang, Hyun Gook [KAIST, Daejeon (Korea, Republic of)

2014-08-15

Spent fuel transportation of South Korea is to be conducted through near sea because it is able to ship a large amount of the spent fuel far from the public comparing to overland transportation. The maritime transportation is expected to be increased and its risk has to be assessed. For the risk assessment, this study utilizes the probabilistic safety assessment (PSA) method and the notions of the combined event. Risk assessment of maritime transportation of spent fuel is not well developed in comparison with overland transportation. For the assessment, first, the transportation scenario should be developed and categorized. Categories are assorted into the locations, release aspects and exposure aspects. This study deals with accident that happens on voyage and concentrated on ship-ship collision. The collision accident scenario is generated with event tree analysis. The scenario will be exploited for the maritime transportation risk model which includes consequence and accident probability.

Alternative Fuel Fleet Vehicle Evaluations | Transportation Research | NREL

Science.gov (United States)

delivery, transit, and freight vehicles. Although biodiesel is the most commonly used alternative fuel in Diesel and Biodiesel Renewable diesel is a conventional petroleum diesel substitute produced from alternative to conventional diesel and does not require any vehicle modifications. Biodiesel is an oxygenated

Risk of transporting spent nuclear fuel by train

International Nuclear Information System (INIS)

Elder, H.K.

1981-12-01

This paper presents results of a study which analyzes the risk of transporting spent fuel by train. The risk assessment methodology consists of 4 basic steps: (1) a description of the system being analyzed; (2) identification of sequences of events that could lead to a release of material during transportation; (3) evaluation of the probability and consequences of each release sequence; and (4) assessment of the risk and evaluation of the results. The conclusion reached was that considering the substantial benefits derived from the fuel, the current spent fuel transportation system poses reasonably low risks

Biomass - alternative renewable energy source to the fossil fuels

Directory of Open Access Journals (Sweden)

Koruba Dorota

2017-01-01

Full Text Available The article presents the fossil fuels combustion effects in terms of the dangers of increasing CO2 concentration in the atmosphere. Based on the bibliography review the negative impact of increased carbon dioxide concentration on the human population is shown in the area of the external environment, particularly in terms of the air pollution and especially the impact on human health. The paper presents biomass as the renewable energy alternative source to fossil fuels which combustion gives a neutral CO2 emissions and therefore should be the main carrier of primary energy in Poland. The paper presents the combustion heat results and humidity of selected dry wood pellets (pellets straw, energy-crop willow pellets, sawdust pellets, dried sewage sludge from two sewage treatment plants of the Holly Cross province pointing their energy potential. In connection with the results analysis of these studies the standard requirements were discussed (EN 14918:2010 “Solid bio-fuels-determination of calorific value” regarding the basic parameters determining the biomass energy value (combustion heat, humidity.

Alternative Fuels Data Center: Biodiesel Truck Transports Capitol Christmas

Science.gov (United States)

Tree Biodiesel Truck Transports Capitol Christmas Tree to someone by E-mail Share Alternative Fuels Data Center: Biodiesel Truck Transports Capitol Christmas Tree on Facebook Tweet about Alternative Fuels Data Center: Biodiesel Truck Transports Capitol Christmas Tree on Twitter Bookmark Alternative

Impact of Transmutation Scenarios on Fuel Transportation

International Nuclear Information System (INIS)

Saturnin, A.; Duret, B.; Allou, A.; Jasserand, F.; Fillastre, E.; Giffard, F.X.; Chabert, C.; Caron-Charles, M.; Garzenne, C.; Laugier, F.

2015-01-01

Minor actinides transmutation scenarios have been studied in the frame of the French Sustainable Radioactive Waste Management Act of 28 June 2006. Transmutation scenarios supposed the introduction of a sodium-cooled fast reactor fleet using homogeneous or heterogeneous recycling modes for the minor actinides. Americium, neptunium and curium (MA) or americium alone (Am) can be transmuted together in a homogeneous way embedded in FR-MOX fuel or incorporated in MA or Am-Bearing radial Blankets (MABB or AmBB). MA transmutation in Accelerator Driven System has also been studied while plutonium is being recycled in SFR. Assessments and comparisons of these advanced cycles have been performed considering technical and economic criteria. Transportation needs for fresh and used transmutation fuels is one of these criteria. Transmutation fuels have specific characteristics in terms of thermal load and neutron emissions. Thermal, radiation and criticality constraints have been taken into account in this study to suggest cask concepts for routine conditions of transport, to estimate the number of assemblies to be transported in a cask and the number of annual transports. Comparison with the no transmutation option, i.e. management of uranium and plutonium in SFRs, is also presented. Regarding these matters, no high difficulties appear for assemblies with limited content of Am (homogeneous or heterogeneous recycling modes). When fuels contain curium, technical transport uncertainties increase because of the important heat release requiring dividing fresh fuels and technological innovations development (MABB and ADS). (authors)

Model documentation Renewable Fuels Module of the National Energy Modeling System

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-01-01

This report documents the objectives, analaytical approach and design of the National Energy Modeling System (NEMS) Renewable Fuels Module (RFM) as it relates to the production of the 1996 Annual Energy Outlook forecasts. The report catalogues and describes modeling assumptions, computational methodologies, data inputs, and parameter estimation techniques. A number of offline analyses used in lieu of RFM modeling components are also described.

Road transport fuels in europe: the explosion of demand for diesel fuel

International Nuclear Information System (INIS)

Bensaid, B.

2004-01-01

In the last 20 years, road transport fuel consumption has more than doubled in European countries, due to strong growth on the diesel passenger car segment and in the transport of road freight. In an economy heavily dependent on oil, European authorities are seeking to promote alternative energy solutions, such as motor fuels produced from biomass

Numerical simulation of ion transport membrane reactors: Oxygen permeation and transport and fuel conversion

KAUST Repository

Hong, Jongsup

2012-07-01

Ion transport membrane (ITM) based reactors have been suggested as a novel technology for several applications including fuel reforming and oxy-fuel combustion, which integrates air separation and fuel conversion while reducing complexity and the associated energy penalty. To utilize this technology more effectively, it is necessary to develop a better understanding of the fundamental processes of oxygen transport and fuel conversion in the immediate vicinity of the membrane. In this paper, a numerical model that spatially resolves the gas flow, transport and reactions is presented. The model incorporates detailed gas phase chemistry and transport. The model is used to express the oxygen permeation flux in terms of the oxygen concentrations at the membrane surface given data on the bulk concentration, which is necessary for cases when mass transfer limitations on the permeate side are important and for reactive flow modeling. The simulation results show the dependence of oxygen transport and fuel conversion on the geometry and flow parameters including the membrane temperature, feed and sweep gas flow, oxygen concentration in the feed and fuel concentration in the sweep gas. © 2012 Elsevier B.V.

Transportation risks in the US nuclear fuel cycle

International Nuclear Information System (INIS)

Rhoads, R.E.; Andrews, W.B.

1980-01-01

Estimated risks associated with accidental releases of materials transported for each step of the nuclear fuel cycle are presented. The risk estimates include both immediate and latent fatilities caused by releases of these materials in transportation accidents. Studies of the risk of transporting yellowcake, fresh nuclear and low level wastes from the front end of the fuel cycle have not been completed. Existing information does permit estimates of the risks to be made. The estimates presented result from the very low hazards associated with release of these materials. These estimates are consistent with the results of other studies. The results show that risks from all the fuel cycle transportation steps are low. The results also indicate that the total transportation risks associated with the nuclear fuel cycle are distributed about evenly between the fuel supply end and waste management end of the cycle. Risks in the front end of the cycle result primarily from the chemical toxicity of the materials transported. The results of the risk analysis studies for transportation of nuclear fuel cycle materials are compared with the results for the three studies that have been completed for non-nuclear systems. The risk analysis methodology used in these studies identifies the complete spectrum of potential accident consequences and estimates the probability of events producing that level of consequence. The maximum number of fatalities predicted for each material is presented. A variety of risk measures have been used because of the inherent difficulties in making risk comparisons. Examination of a number of risk measures can provide additional insights and help guard against conclusions that are dependent on the way the risk information has been developed and displayed. The results indicate that the risks from transporting these materials are all relatively low in comparison to other risks in society

Design of a transportation cask for irradiated CANDU fuel

International Nuclear Information System (INIS)

Nash, K.E.; Gavin, M.E.

1983-01-01

A major step in the development of a large-scale transportation system for irradiated CANDU fuel is being made by Ontario Hydro in the design and construction of a demonstration cask by 1988/89. The system being designed is based on dry transportation with the eventual fully developed system providing for dry fuel loading and unloading. Research carried out to date has demonstrated that it is possible to transport irradiated CANDU fuel in a operationally efficient and simple manner without any damage which would prejudice subsequent automated fuel handling

Spent Fuel Transportation Package Performance Study - Experimental Design Challenges

International Nuclear Information System (INIS)

Snyder, A. M.; Murphy, A. J.; Sprung, J. L.; Ammerman, D. J.; Lopez, C.

2003-01-01

Numerous studies of spent nuclear fuel transportation accident risks have been performed since the late seventies that considered shipping container design and performance. Based in part on these studies, NRC has concluded that the level of protection provided by spent nuclear fuel transportation package designs under accident conditions is adequate. [1] Furthermore, actual spent nuclear fuel transport experience showcase a safety record that is exceptional and unparalleled when compared to other hazardous materials transportation shipments. There has never been a known or suspected release of the radioactive contents from an NRC-certified spent nuclear fuel cask as a result of a transportation accident. In 1999 the United States Nuclear Regulatory Commission (NRC) initiated a study, the Package Performance Study, to demonstrate the performance of spent fuel and spent fuel packages during severe transportation accidents. NRC is not studying or testing its current regulations, a s the rigorous regulatory accident conditions specified in 10 CFR Part 71 are adequate to ensure safe packaging and use. As part of this study, NRC currently plans on using detailed modeling followed by experimental testing to increase public confidence in the safety of spent nuclear fuel shipments. One of the aspects of this confirmatory research study is the commitment to solicit and consider public comment during the scoping phase and experimental design planning phase of this research

Transport of MOX fuel from Europe to Japan; Transport de combustible mox d' Europe vers le Japon

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-07-01

The MOX fuel transports from Europe to Japan represent a main part in the implementing of the Japan nuclear program. They complement the 160 transports of spent fuels realized from Japan to Europe and the vitrified residues return from France to Japan. In this framework the document presents the MOX fuel, the use of the MOX fuel in reactor, the proliferation risks, the MOX fuel transport to Japan, the public health, the transport regulations, the safety and the civil liability. (A.L.B.)

Minnesota's Home-Grown Transportation Fuel

Energy Technology Data Exchange (ETDEWEB)

2002-10-01

Minnesota leads the country in production and consumption of ethanol E-85 transportation. DOE's State Energy Program supports energy efficiency and renewable energy projects in the states through the state energy offices.

Repurposing PEV batteries : supporting renewables meet the drivers

International Nuclear Information System (INIS)

Bibeau, E.

2009-01-01

Methods of repurposing plug-in hybrid electric vehicle (PHEV) batteries were presented. Declining fossil fuel resources and increased environmental emissions are driving the need to repurpose PHEV batteries. Current paths to address energy drivers in transportation include the use of hydrogen; the reduction of tailpipe emissions; an increased use of biofuels; and reductions in fossil fuel usage. Electric mobility can also be combined with other methods to provide a sustainable long-term approach to transportation management. An increase in electric mobility will aid in ensuring that Canada's overall energy management strategy is successful. It was concluded that the addition of renewable energy resources will increase energy efficiency and lower energy demand. tabs., figs.

Achieving stringent climate targets. An analysis of the role of transport and variable renewable energies using energy-economy-climate models

Energy Technology Data Exchange (ETDEWEB)

Pietzcker, Robert Carl

2014-07-01

Anthropogenic climate change is threatening the welfare of mankind. Accordingly, policy makers have repeatedly stated the goal of slowing climate change and limiting the increase of global mean temperature to less than 2 C above pre-industrial times (the so-called ''two degree target''). Stabilizing the temperature requires drastic reductions of greenhouse gas (GHG) emissions to nearly zero. As the global system of energy supply currently relies on fossil fuels, reducing GHG emissions can only be achieved through a full-scale transformation of the energy system. This thesis investigates the economic requirements and implications of different scenarios that achieve stringent climate mitigation targets. It starts with the analysis of characteristic decarbonization patterns and identifies two particularly relevant aspects of mitigation scenarios: deployment of variable renewable energies (VRE) and decarbonization of the transport sector. After investigating these fields in detail, we turned towards one of the most relevant questions for policy makers and analyzed the trade-off between the stringency of a climate target and its economic requirements and implications. All analyses are based on the improvement, application, comparison, and discussion of large-scale IAMs. The novel ''mitigation share'' metric allowed us to identify the relevance of specific technology groups for mitigation and to improve our understanding of the decarbonization patterns of different energy subsectors. It turned out that the power sector is decarbonized first and reaches lowest emissions, while the transport sector is slowest to decarbonize. For the power sector, non-biomass renewable energies contribute most to emission reductions, while the transport sector strongly relies on liquid fuels and therefore requires biomass in combination with carbon capture and sequestration (CCS) to reduce emissions. An in-depth investigation of the solar power

Sensor system for fuel transport vehicle

Science.gov (United States)

Earl, Dennis Duncan; McIntyre, Timothy J.; West, David L.

2016-03-22

An exemplary sensor system for a fuel transport vehicle can comprise a fuel marker sensor positioned between a fuel storage chamber of the vehicle and an access valve for the fuel storage chamber of the vehicle. The fuel marker sensor can be configured to measure one or more characteristics of one or more fuel markers present in the fuel adjacent the sensor, such as when the marked fuel is unloaded at a retail station. The one or more characteristics can comprise concentration and/or identity of the one or more fuel markers in the fuel. Based on the measured characteristics of the one or more fuel markers, the sensor system can identify the fuel and/or can determine whether the fuel has been adulterated after the marked fuel was last measured, such as when the marked fuel was loaded into the vehicle.

Smart Energy Systems for coherent 100% renewable energy and transport solutions

DEFF Research Database (Denmark)

Mathiesen, Brian Vad; Lund, Henrik; Connolly, David

2015-01-01

The hypothesis of this paper is that in order to identify least cost solutions of the integration of fluctuating renewable energy sources into current or future 100% renewable energy supplies one has to take a Smart Energy Systems approach. This paper outline why and how to do so. Traditionally......, significant focus is put on the electricity sector alone to solve the renewable energy integration puzzle. Smart grid research traditionally focuses on ICT, smart meters, electricity storage technologies, and local (electric) smart grids. In contrast, the Smart Energy System focuses on merging the electricity......, heating and transport sectors, in combination with various intra-hour, hourly, daily, seasonal and biannual storage options, to create the flexibility necessary to integrate large penetrations of fluctuating renewable energy. However, in this paper we present the development and design of coherent Smart...

Studies of Lanthanide Transport in Metallic Fuel

Energy Technology Data Exchange (ETDEWEB)

Zhang, Jinsuo; Taylor, Christopher

2018-04-02

Metallic nuclear fuels were tested in fast reactor programs and performed well. However, metallic fuels have shown the phenomenon of FCCI that are due to deleterious reactions between lanthanide fission products and cladding material. As the burnup is increased, lanthanide fission products that contact with the cladding could react with cladding constituents such as iron and chrome. These reactions produce higher-melting intermetallic compounds and low-melting alloys, and weaken the mechanical integrity. The lanthanide interaction with clad in metallic fuels is recognized as a long-term, high-burnup cause of the clad failures. Therefore, one of the key concerns of using metallic fuels is the redistribution of lanthanide fission products and migration to the fuel surface. It is believed that lanthanide migration is in part due to the thermal gradient between the center and the fuel-cladding interface, but also largely in part due to the low solubility of lanthanides within the uranium-based metal fuel. PIE of EBR-II fuels shows that lanthanides precipitate directly and do not dissolve to an appreciable extent in the fuel matrix. Based on the PIE data from EBR-II, a recent study recommended a so-called “liquid-like” transport mechanism for lanthanides and certain other species. The liquid-like transport model readily accounts for redistribution of Ln, noble metal fission products, and cladding components in the fuel matrix. According to the novel mechanism, fission products can transport as solutes in liquid metals, such as liquid cesium or liquid cesium–sodium, and on pore surfaces and fracture surfaces for metals near their melting temperatures. Transport in such solutions is expected to be much more rapid than solid-state diffusion. The mechanism could explain the Ln migration to the fuel slug peripheral surface and their deposition with a sludge-like form. Lanthanides have high solubility in liquid cesium but have low solubility in liquid sodium. As a

National Renewable Energy Laboratory 2002 Research Review (Booklet)

Energy Technology Data Exchange (ETDEWEB)

Cook, G.; Epstein, K.; Brown, H.

2002-07-01

America is making a long transition to a future in which conventional, fossil fuel technologies will be displaced by new renewable energy and energy efficiency technologies. This first biannual research review describes NREL's R&D in seven technology areas--biorefineries, transportation, hydrogen, solar electricity, distributed energy, energy-efficient buildings, and low-wind-speed turbines.

Spent-fuel transportation - a success story

International Nuclear Information System (INIS)

Gertz, C.P.; Schoonen, D.H.; Wakeman, B.H.

1986-01-01

Spent nuclear fuel research and development (R and D) demonstrations and associated transportation activities are being performed as a part of the storage cask performance testing programs at the Idaho National Engineering Laboratory (INEL). These spent-fuel programs support the Nuclear Waste Policy Act (NWPA) and US Department of Energy (DOE) objectives for cooperative demonstrations with the utilities, testing at federal sites, and alternatives for viable transportation systems. A cooperative demonstration program with the private sector to develop dry storage technologies that the US Nuclear Regulatory Commission (NRC) can generically approve is in place as well as cost-shared dry storage R and D program at a federal facility to collect the necessary licensing data. In addition to the accomplishments in the cask performance and testing demonstrations, the long-distance transportation of a large number of spent-fuel assemblies is considered a success story. The evaluation and implementation of applicable requirements, industry perspective, and extensive planning all contributed to this achievement

Sizing stack and battery of a fuel cell hybrid distribution truck

NARCIS (Netherlands)

Bram Veenhuizen; Y. Shen; P.P.J. van den Bosch; Edwin Tazelaar; T. Hofman

2012-01-01

Fuel cell hybrid vehicles are believed to provide a solution to cut down emissions in the long term. They provide local zero-emission propulsion and when the hydrogen as fuel is derived from renewable energy sources, fuel cell hybrids enable well-to-wheel zero-emission transportation,

Catalyst technology for biofuel production: Conversion of renewable lipids into biojet and biodiesel

Directory of Open Access Journals (Sweden)

Scharff Yves

2013-09-01

Full Text Available Renewable lipids based biofuels are an important tool to address issues raised by policies put in place in order to reduce the dependence of transportation sector on fossil fuels and to promote the development of non-food based, sustainable and eco-friendly fuels. This paper presents the main features of the heterogeneous catalysis technologies Axens has developed for the production of biofuels from renewable lipids: the first by transesterification to produce fatty acid methyl esters or biodiesel and the second by hydrotreating to produce isoparaffinic hydroprocessed ester and fatty acids, high blending rate drop-in diesel and jet biofuels.

The myth and realities of renewable energy

International Nuclear Information System (INIS)

Shargal, M.; Houseman, D.

2008-01-01

Renewable energies use natural resources such as sunlight, wind, rain, tides, and geothermal heat, which are naturally replenished. Renewable energy technologies range from wind power, hydroelectricity, wave, solar, biomass, and biofuels. While most renewable energy sources do not produce pollution directly, the materials, industrial processes, and construction equipment used to create them may generate waste and pollution. This paper discussed the myths and realities of these energy applications. The following were described as being myths: plug-in cars could help reduce air pollution; current electric infrastructure can support the growth in plug-in cars; transmission grid can support the transportation of renewable electricity generated in rural areas to homes and business that need it in large metropolitan areas; there is a shortage of renewable energy sources on earth; biofuels do not have environmental issues; renewable energy facilities last forever; biofuel and biomass energy positively influence greenhouse gas; and greater efficiency results in lower energy consumption, resulting in energy independence. The paper also addressed the myth that ethanol is an eco-friendly fuel, and that if the United States tapped into its vast coal reserves effectively with clean and efficient coal-to-liquids technology, America would achieve energy independence. The paper also discussed the transformation from surplus fossil fuel resources to constrained gas and oil carriers, and subsequently to new energy supply and conversion technologies. Specifically, the paper addressed carbon offsets and allowance, cow power, and innovative experiments. It was concluded that the world is not on course to achieve a sustainable energy future. The global energy supply will continue to be dominated by fossil fuels for several decades. In order to reduce the resultant greenhouse gas emissions, a transition to zero and low-carbon technologies will be required. 10 refs

Renewable sustainable biocatalyzed electricity production in a photosynthetic algal microbial fuel cell (PAMFC)

NARCIS (Netherlands)

Strik, D.P.B.T.B.; Terlouw, H.; Hamelers, H.V.M.; Buisman, C.J.N.

2008-01-01

Electricity production via solar energy capturing by living higher plants and microalgae in combination with microbial fuel cells are attractive because these systems promise to generate useful energy in a renewable, sustainable, and efficient manner. This study describes the proof of principle of a

On Combustion in the CNG-Diesel Dual Fuel Engine

OpenAIRE

Königsson, Fredrik

2014-01-01

Currently there is a large interest in alternative transport fuels. There are two underlying reasons for this interest: the desire to decrease the environmental impact of transports and the need to compensate for the declining availability of petroleum. In the light of both these factors, the CNG-diesel dual fuelengine is an attractive concept. The primary fuel of the dual fuel engine is methane, which can be derived both from renewables and from fossil sources. Methane from organic waste, co...

Agricultural transportation fuels

International Nuclear Information System (INIS)

Anon.

1993-01-01

The recommendations on the title subject are focused on the question whether advantages and disadvantages of agricultural fuels compared to fossil fuels justify the Dutch policy promotion of the use of agricultural products as basic materials for agricultural fuels. Attention is paid to energetic, environmental and economical aspects of both fuel types. Four options to apply agricultural transportation fuels are discussed: (1) 10% bio-ethanol in euro-unleaded gasoline for engines of passenger cars, equipped with a three-way catalyst; (2) the substitution of 15% methyl tertiair butyl ether (MTBE) by ethyl tertiair butyl ether (ETBE) as a substituent for lead in unleaded super plus gasoline (Sp 98) for engines of passenger cars, equipped with a three-way catalyst; (3) 50% KME (rapeseed oil ester) in low-sulfur diesel (0.05%S D) for engines of vans without a catalyst; and (4) the substitution of 0.05% S D by bio-ethanol or KME for buses with fuel-adjusted engines, equipped with a catalyst. Also the substitution by liquefied petroleum gas (LPG), compressed natural gas (CNG) or E 95 was investigated in option four. Each of the options investigated can contribute to a reduction of the use of fossil energy and the environmental effects of the use of fossil fuels, although some environmental effects from agricultural fuels must be taken into consideration. It is recommended to seriously pay attention to the promotion of agricultural fuels, not only in the Netherlands, but also in an international context. Policy instruments to be used in the stimulation of the use of such fuels are the existing European Community subsidies on fallow lands, exemption of the European Community energy levy, and the use of tax differentiation. Large-scale demonstration projects must be started to quantify hazardous emissions and to solve still existing technical problems. 8 figs., 3 tabs., refs., 4 appendices

Considerations for the transportation of spent fuel

International Nuclear Information System (INIS)

Jefferson, R.M.

1984-01-01

In our society today the transportation of radioactive materials, and most particularly spent reactor fuel, is surrounded by considerable emotion and a wealth of information, good and bad. The transportation of these materials is viewed as unique and distinct from the transportation of other hazardous materials and as a particularly vulnerable component of the nuclear power activities of this nation. Added to this is the concept, widely held, that almost everyone is an expert on the transportation of radioactive materials. One significant contribution to this level of emotion is the notion that all roads (rail and highway), on which these goods will be transported, somehow traverse everyone's backyard. The issue of the transportation of spent fuel has thus become a political battleground. Perhaps this should not be surprising since it has all of the right characteristics for such politicization in that it is pervasive, emotional, and visible. In order that those involved in the discussion of this activity might be able to reach some rational conclusions, this paper offers some background information which might be useful to a broad range of individuals in developing their own perspectives. The intent is to address the safety of transporting spent fuel from a technical standpoint without the emotional content which is frequently a part of this argument

Evaluation of Suppression of Hydroprocessed Renewable Jet (HRJ) Fuel Fires with Aqueous Film Forming Foam (AFFF)

Science.gov (United States)

2011-07-01

Collecting particles from an open pan fire would preclude the consideration of isokinetic sampling usually required in Method 5, but this would...hydroprocessed renewable jet fuel in2 square inches JP-8 jet propellant 8, i.e. jet fuel kW kilowatts m2 square meters Mil-Spec Military Specification min

Renewable sustainable biocatalyzed electricity production in a photosynthetic algal microbial fuel cell (PAMFC)

Energy Technology Data Exchange (ETDEWEB)

Strik, David P.B.T.B.; Terlouw, Hilde; Hamelers, Hubertus V.M.; Buisman, Cees J.N. [Wageningen Univ. (Netherlands). Sub-Dept. of Environmental Technology

2008-12-15

Electricity production via solar energy capturing by living higher plants and microalgae in combination with microbial fuel cells are attractive because these systems promise to generate useful energy in a renewable, sustainable, and efficient manner. This study describes the proof of principle of a photosynthetic algal microbial fuel cell (PAMFC) based on naturally selected algae and electrochemically active microorganisms in an open system and without addition of instable or toxic mediators. The developed solar-powered PAMFC produced continuously over 100 days renewable biocatalyzed electricity. The sustainable performance of the PAMFC resulted in a maximum current density of 539 mA/m{sup 2} projected anode surface area and a maximum power production of 110 mW/m{sup 2} surface area photobioreactor. The energy recovery of the PAMFC can be increased by optimization of the photobioreactor, by reducing the competition from non-electrochemically active microorganisms, by increasing the electrode surface and establishment of a further-enriched biofilm. Since the objective is to produce net renewable energy with algae, future research should also focus on the development of low energy input PAMFCs. This is because current algae production systems have energy inputs similar to the energy present in the outcoming valuable products. (orig.)

The Role of Distribution Infrastructure and Equipment in the Life-cycle Air Emissions of Liquid Transportation Fuels

Science.gov (United States)

Strogen, Bret Michael

component. In order to apply the new emission factors to policy-relevant scenarios, a projection is made for the fleet inventory of infrastructure components necessary to distribute 21 billion gallons of ethanol (the 2022 federal mandate for advanced biofuels under the Energy Independence and Security Act of 2007) derived entirely from Miscanthus grass, for comparison to the baseline petroleum system. Due to geographic, physical and chemical properties of biomass and alcohols, the distribution system for Miscanthus-based ethanol is more capital- and energy-intensive than petroleum per unit of fuel energy delivered. The transportation of biofuels away from producer regions poses environmental, health, and economic trade-offs that are herein evaluated using a simplified national distribution network model. In just the last ten years, ethanol transportation within the contiguous United States is estimated to have increased more than ten-fold in total t-km as ethanol has increasingly been transported away from Midwest producers due to air quality regulations pertaining to gasoline, renewable fuel mandates, and the 10% blending limit (i.e., the E10 blend wall). From 2004 to 2009, approximately 10 billion t-km of ethanol transportation are estimated to have taken place annually for reasons other than the E10 blend wall, leading to annual freight costs greater than $240 million and more than 300,000 tonnes of CO2-e emissions and significant emissions of criteria air pollutants from the combustion of more than 90 million liters of diesel. Although emissions from distribution activities are small when normalized to each unit of fuel, they are large in scale. Archetypal fuel distribution routes by rail and by truck are created to evaluate the significance of mode choice and route location on the severity of public health impacts from locomotive and truck emissions, by calculating the average PM2.5 pollution intake fraction along each route. Exposure to pollution resulting from

Integrated risk assessment for spent fuel transportation using developed software

International Nuclear Information System (INIS)

Yun, Mi Rae; Christian, Robby; Kim, Bo Gyung; Almomani, Belal; Ham, Jae Hyun; Kang, Gook Hyun; Lee, Sang hoon

2016-01-01

As on-site spent fuel storage meets limitation of their capacity, spent fuel need to be transported to other place. In this research, risk of two ways of transportation method, maritime transportation and on-site transportation, and interim storage facility were analyzed. Easier and integrated risk assessment for spent fuel transportation will be possible by applying this software. Risk assessment for spent fuel transportation has not been researched and this work showed a case for analysis. By using this analysis method and developed software, regulators can get some insights for spent fuel transportation. For example, they can restrict specific region for preventing ocean accident and also they can arrange spend fuel in interim storage facility avoiding most risky region which have high risk from aircraft engine shaft. Finally, they can apply soft material on the floor for specific stage for on-site transportation. In this software, because we targeted Korea, we need to use Korean reference data. However, there were few Korean reference data. Especially, there was no food chain data for Korean ocean. In MARINRAD, they used steady state food chain model, but it is far from reality. Therefore, to get Korean realistic reference data, dynamic food chain model for Korean ocean need to be developed

Integrated risk assessment for spent fuel transportation using developed software

Energy Technology Data Exchange (ETDEWEB)

Yun, Mi Rae; Christian, Robby; Kim, Bo Gyung; Almomani, Belal; Ham, Jae Hyun; Kang, Gook Hyun [KAIST, Daejeon (Korea, Republic of); Lee, Sang hoon [Keimyung University, Daegu (Korea, Republic of)

2016-05-15

As on-site spent fuel storage meets limitation of their capacity, spent fuel need to be transported to other place. In this research, risk of two ways of transportation method, maritime transportation and on-site transportation, and interim storage facility were analyzed. Easier and integrated risk assessment for spent fuel transportation will be possible by applying this software. Risk assessment for spent fuel transportation has not been researched and this work showed a case for analysis. By using this analysis method and developed software, regulators can get some insights for spent fuel transportation. For example, they can restrict specific region for preventing ocean accident and also they can arrange spend fuel in interim storage facility avoiding most risky region which have high risk from aircraft engine shaft. Finally, they can apply soft material on the floor for specific stage for on-site transportation. In this software, because we targeted Korea, we need to use Korean reference data. However, there were few Korean reference data. Especially, there was no food chain data for Korean ocean. In MARINRAD, they used steady state food chain model, but it is far from reality. Therefore, to get Korean realistic reference data, dynamic food chain model for Korean ocean need to be developed.

The decision-making that disregarded electrofuels as alternative within transport

DEFF Research Database (Denmark)

Ridjan, Iva; Mathiesen, Brian Vad

on the decision-making that made biofuels one of the main solutions for the transport sector as well as on the stakeholders that influenced the development of these fuels and relevant policies. The search will also try to identify how policies recognize electrofuels or Carbon Capture and Recycling (CCR......) as potential alternatives in the climate mitigation and set up renewable energy goals as well as how this is reflecting on solving the transport sector transition to renewable energy. The results indicate that biofuels are still the only supported liquid renewable alternative to be utilized in the transport...

What are the environmental benefits of electric vehicles? A life cycle based comparison of electric vehicles with biofuels, hydrogen and fossil fuels

Energy Technology Data Exchange (ETDEWEB)

Jungmeier, Gerfried; Canella, Lorenza; Beermann, Martin; Pucker, Johanna; Koenighofer, Kurt [JOANNEUM RESEARCH Forschungsgesellschaft mbH, Graz (Austria)

2013-06-01

The Renewable Energy Directive aims reaching a share of 10% of renewable fuels in Europe in 2020. These renewable fuels are transportation biofuels, renewable electricity and renewable hydrogen. In most European countries transportation biofuels are already on the transportation fuel market in significant shares, e.g. in Austria 7% by blending bioethanol to gasoline and biodiesel to diesel. Electric vehicles can significantly contribute towards creating a sustainable, intelligent mobility and intelligent transportation systems. They can open new business opportunities for the transportation engineering sector and electricity companies. But the broad market introduction of electric vehicles is only justified due to a significant improvement of the environmental impact compared to conventional vehicles. This means that in addition to highly efficient electric vehicles and renewable electricity, the overall environmental impact in the life cycle - from building the vehicles and the battery to recycling at the end of its useful life - has to be limited to an absolute minimum. There is international consensus that the environmental effects of electric vehicles (and all other fuel options) can only be analysed on the basis of life cycle assessment (LCA) including the production, operation and the end of life treatment of the vehicles. The LCA results for different environmental effects e.g. greenhouse gas emissions, primary energy consumption, eutrophication will be presented in comparison to other fuels e.g. transportation biofuels, gasoline, natural gas and the key factors to maximize the environmental benefits will be presented. The presented results are mainly based on a national research projects. These results are currently compared and discussed with international research activities within the International Energy Agency (lEA) in the Implementing Agreement on Hybrid and Electric Vehicles (IA-HEV) in Task 19 ''Life Cycle Assessment of Electric Vehicles

Determination of prerequisites for the estimation of transportation cost of spent fuels

International Nuclear Information System (INIS)

Choi, Heui Joo; Lee, Jong Youl; Kim, Seong Ki; Cha, Jeong Hoon; Choi, Jong Won

2007-10-01

The cost for the spent fuel management includes the costs for the interim storage, the transportation, and the permanent disposal of the spent fuels. The scope of this report is limited to the cost for the spent fuel transportation. KAERI is developing a cost estimation method for the spent fuel transportation through a joint study with the French AREVA TN. Several prerequisites should be fixed in order to estimate the cost for the spent fuel transportation properly. In this report we produced them considering the Korean current status on the management of spent fuels. The representative characteristics of a spent fuel generated from the six nuclear reactors at the YG site were determined. Total 7,200 tons of spent fuels are projected with the lifespan of 60 years. As the transportation mode, sea transportation and road transportation is recommended considering the location of the YG site and the hypothetical Centralized Interim Storage Facility (CISF) and Final Repository (FR). The sea route and transportation time were analyzed by using a sea distance analysis program which the NORI (National Oceanographic Research Institute) supplies on a web. Based on the results of the analysis, the shipping rates were determined. The regulations related to the spent fuel transportation were reviewed. The characteristics of the transportation vessel and a trailer were suggested. The handling and transportation systems at the YG site, Centralized Interim Storage Facility, and the Final Repository were described in detail for the purpose of the cost estimation of the spent fuel transportation. From the detail description the major components of the transportation system were determined for the conceptual design. It is believed that the conceptual design of the transportation system developed in this report will be used for the analysis of transportation logistics and the cost estimation of spent fuels

Transport of nuclear used fuel and waste materials

Energy Technology Data Exchange (ETDEWEB)

Neau, H.J. [World Nuclear Transport Institute, London (United Kingdom)

2015-07-01

20 millions consignments of radioactive materials are routinely transported annually on public roads, railways and ships. 5% of these are nuclear fuel cycle related. International Atomic Energy Agency Regulations have been in force since 1961. The sector has an excellent safety record spanning over 50 years. Back end transport covers the operations concerned with spent fuel that leaves reactors and wastes. Since 1971, there have been 70,000 shipments of used fuel (i.e. over 80,000 tonnes) with no damage to property or person. The excellent safety record spanning over 50 years praised every year by the General Conference of the International Atomic Energy Agency. More than 200 sea voyages over a distance of more than 8 million kilometres of transport of used fuel or high-level wastes.

Transportation fuel from plastic: Two cases of study.

Science.gov (United States)

Faussone, Gian Claudio

2018-03-01

Synthesis of liquid fuels from waste is a promising pathway for reducing the carbon footprint of transportation industry and optimizing waste management towards zero landfilling. The study of commercial plants that conduct pyrolysis of plastics from post-consumer recycled materials and directly mine from old landfills without any pre-treatment has revealed two cases that show the feasibility of manufacturing transportation fuels via these methods. Pyrolysis oil, consisting of almost 26% hydrocarbons within the gasoline range and almost 70% within the diesel range, is upgraded to transportation fuel in the existing refinery. A batch operating plant is able to deliver relatively good quality pyrolysis oil from post-consumer plastic waste, owing to the catalyst employed. Simple distillation was also evaluated as an alternative and cheaper upgrading process into transportation fuels, meeting EN590 diesel and ISO8217 marine fuel standards. Even though the two installations are outside the European Union, they represent good examples of the "circular economy" concept envisaged by the European Union via its ambitious "Circular Economy Package [1]", providing real world data for comparison with other experimental and lab results. Copyright © 2017 Elsevier Ltd. All rights reserved.

Enabling alternate fuels for commercial aircraft

OpenAIRE

Daggett, D.

2010-01-01

The following reports on the past four years of work to examine the feasibility, sustainability and economic viability of developing a renewable, greenhouse-gas-neutral, liquid biofuel for commercial aircraft. The sharp increase in environmental concerns, such as global warming, as well as the volatile price fluctuations of fossil fuels, has ignited a search for alternative transportation fuels. However, commercial aircraft can not use present alternative fuels that are designed for ground...

Environmental economics of lignin derived transport fuels

OpenAIRE

Obydenkova, SV; Kouris, P Panagiotis; Hensen, EJM Emiel; Heeres, Hero J; Boot, MD Michael

2017-01-01

This paper explores the environmental and economic aspects of fast pyrolytic conversion of lignin, obtained from 2G ethanol plants, to transport fuels for both the marine and automotive markets. Various scenarios are explored, pertaining to aggregation of lignin from several sites, alternative energy carries to replace lignin, transport modalities, and allocation methodology. The results highlight two critical factors that ultimately determine the economic and/or environmental fuel viability....

Techno-Economic Analysis of Camelina-Derived Hydroprocessed Renewable Jet Fuel and its Implications on the Aviation Industry

Science.gov (United States)

Shila, Jacob Joshua Howard

Although the aviation industry contributes toward global economic growth via transportation of passengers and cargo, the increasing demand for air transportation causes concern due to the corresponding increase in aircraft engine exhaust emissions. Use of alternative fuels is one pathway that has been explored for reducing emissions in the aviation industry. Hydroprocessed renewable jet (HRJ) (also known as Hydroprocessed Esters and Fatty Acids - HEFA) fuels have been approved for blending with traditional jet fuel up to 50% by volume to be used as drop-in fuels. However, limited information exists on the economic viability of these fuels. While techno-economic studies have been conducted on the HRJ production process using soybean oil, different vegetable oils possess different hydrocarbon structures that affect the yield of HRJ fuels. This study involves the techno-economic analysis of producing Camelina-derived HRJ fuel using the option of hydro-deoxygenation (HDO). The hydrodeoxygenation option requires extra hydrogen and hence affects the overall cost of HRJ fuel production. Similar studies have been conducted on the production of Camelina-derived HRJ fuels using the same path of hydrodeoxygenation with minor contributions from both decarbonylation and decarboxylation reactions. This study, however, employs the UOP Honeywell procedure using the hydrodeoxygenation chemical reaction to estimate the breakeven price of Camelina-derived HRJ fuel. In addition, the study treats the cultivation of Camelina oilseeds, extraction of oilseeds, and the conversion of HRJ fuel as separate entities. The production of Camelina oilseed, Camelina oil, and finally Camelina-derived HRJ fuel is modeled in order to estimate the breakeven price of the fuel. In addition, the information obtained from the techno-economic analysis is used to assess the breakeven carbon price. All costs are analyzed based on 2016 US dollars. The breakeven price of Camelina oilseeds is found to be 228

Transport of MOX fuel from Europe to Japan; Transport de combustible mox d' Europe vers le Japon

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-07-01

The MOX fuel transports from Europe to Japan represent a main part in the implementing of the Japan nuclear program. They complement the 160 transports of spent fuels realized from Japan to Europe and the vitrified residues return from France to Japan. In this framework the document presents the MOX fuel, the use of the MOX fuel in reactor, the proliferation risks, the MOX fuel transport to Japan, the public health, the transport regulations, the safety and the civil liability. (A.L.B.)

Subsidy regulation in WTO Law : Some implications for fossil fuels and renewable energy

NARCIS (Netherlands)

Marhold, Anna

2016-01-01

This contribution discusses WTO subsidies disciplines in the context of the energy sector. After laying out the relevant disciplines, it will discuss the paradox of WTO law with respect to subsidies towards fossil fuels vis-à-vis those towards renewable energy. It is clear that subsidies on clean

Renewable energy production - A business for the future?

International Nuclear Information System (INIS)

2002-01-01

The report is the result of a study performed in 2002. Main objectives of the study were: Is there a potential for growth for the Swedish companies active in the business of renewable energy? Can these companies develop into internationally competitive industries? The areas studied are: Biofuels, Bio-based transportation fuels, Wastes, Small scale hydro power, Wind power, Solar cells and Hydrogen

High-Density Renewable Fuels Based on the Selective Dimerization of Pinenes

Science.gov (United States)

2009-01-01

RJ-5, significant ring strain contributing to a high heat of combustion (Table 1). Bulk agricultural waste products, such as cellulose and lignin , are...compact structures and reactive olefin functionalities, these molecules have sig- nificant potential as feedstocks for high-density renewable fuels.2b,7...potential to have heating values exceeding that of JP-10. Given the favorable potential net heat of combustion for these pinene dimers, reactivity

Regional income effects and renewable fuels. Increased usage of renewable energy sources in Danish rural areas and its impact on regional incomes

Energy Technology Data Exchange (ETDEWEB)

Bentzen, J.; Smith, V. [Aarhus School of Business, Dept. of Economics (Denmark); Dilling-Hansen, M. [Univ. of Aarhus, Dept. of Management (Denmark)

1996-12-31

CO{sub 2}-emission is a world wide problem and in the attempt to reduce these emissions, renewable energy sources may be considered serious alternatives to the present usage of fossil fuels. As part of a research programme financed by The Danish Energy Agency, data concerning the different heating technologies based on oil and wood fuels have been collected. Private and social costs are estimated and these economic data are used when analysing regional income effects of increased consumption of fuels (e.g. wood) locally produced. The impacts on income and tax revenues are calculated from multiplier expressions, constructed with rights to the measurement of local effects. (au) 10 refs.

Regional income effects and renewable fuels. Increased usage of renewable energy sources in Danish rural areas and its impact on regional incomes

International Nuclear Information System (INIS)

Bentzen, J.; Smith, V.; Dilling-Hansen, M.

1996-01-01

CO 2 -emission is a world wide problem and in the attempt to reduce these emissions, renewable energy sources may be considered serious alternatives to the present usage of fossil fuels. As part of a research programme financed by The Danish Energy Agency, data concerning the different heating technologies based on oil and wood fuels have been collected. Private and social costs are estimated and these economic data are used when analysing regional income effects of increased consumption of fuels (e.g. wood) locally produced. The impacts on income and tax revenues are calculated from multiplier expressions, constructed with rights to the measurement of local effects. (au) 10 refs

Biogas: A renewable energy source

International Nuclear Information System (INIS)

Imiere, E.E.; Ojih, V.B.; Esiekpe, L.E.; Okafor, M.C.; Attoh, V. A.

2011-01-01

Biogas refers to a gas produced by the biological breakdown of organic matter in the absence of oxygen. Biogas can be used as a fuel in any country for any heating purpose such as cooking. By means of digesters, the energy in the gas can be converted to electricity and heat. Biogas like natural gas can also be used to power motor vehicle. Biogas is a renewable fuel which qualifies it for a renewable energy subsidy. It is non-toxic, environment-friendly and serve as a means of combating global warming. Biogas is presently being used in U.S.A, U.K, China, Sweden, Brazil, and India amongst others for domestic purposes, transportation and power generation. In this regard, this paper discusses biogas production. It also presents a model design of domestic biogas plant suitable for Nigerian households. The paper recommends that Nigerian Government should intensify efforts in educating the masses on this novel technology for a sustainable global development. A biogas plant designed for Nigerian household discussed in this paper is also recommended.

Safety evaluation on MOX new fuel at marine transport

International Nuclear Information System (INIS)

Tsumune, Daisuke; Ito, Chihiro; Saegusa, Toshiari; Maruyama, Koki

2000-01-01

In the Central Research Institute of Electric Power Industry, in order to confirm effects of MOX new fuel on the public are as small as possible even when its marine transport goes down, some exposed radiation dose has previously conducted on imaginary shipwreck of marine transport on used nuclear fuel, plutonium dioxide, and high level return glass solid. Under a base of such informations, some investigations on safety on marine transport of the MOX new fuel was conducted. On September, 1999, five transport vessels of the MOX new fuel was at first transported on marine. The value of five times of estimated exposed radiation dose (max. 8.1 x 10 -8 mSv/y) corresponds to an evaluation result assumed by shipwreck in marine transport this time. As a result, it was found that the exposed radiation dose estimated on this case would be sufficiently less than an effective dose equivalent limit (1 mSv/y) of public exposure according to the recommendation of ICRP in both coastal and oceanic areas. (G.K.)

Transport phenomena in fuel cells : from microscale to macroscale

Energy Technology Data Exchange (ETDEWEB)

Djilali, N. [Victoria Univ., BC (Canada). Dept. of Mechanical Engineering]|[Victoria Univ., BC (Canada). Inst. for Integrated Energy Systems

2006-07-01

Proton Exchange Membrane (PEM) fuel cells rely on an array of thermofluid transport processes for the regulated supply of reactant gases and the removal of by-product heat and water. Flows are characterized by a broad range of length and time scales that take place in conjunction with reaction kinetics in a variety of regimes and structures. This paper examined some of the challenges related to computational fluid dynamics (CFD) modelling of PEM fuel cell transport phenomena. An overview of the main features, components and operation of PEM fuel cells was followed by a discussion of the various strategies used for component modelling of the electrolyte membrane; the gas diffusion layer; microporous layer; and flow channels. A review of integrated CFD models for PEM fuel cells included the coupling of electrochemical thermal and fluid transport with 3-D unit cell simulations; air-breathing micro-structured fuel cells; and stack level modelling. Physical models for modelling of transport at the micro-scale were also discussed. Results of the review indicated that the treatment of electrochemical reactions in a PEM fuel cell currently combines classical reaction kinetics with solutions procedures to resolve charged species transport, which may lead to thermodynamically inconsistent solutions for more complex systems. Proper representation of the surface coverage of all the chemical species at all reaction sites is needed, and secondary reactions such as platinum (Pt) dissolution and oxidation must be accounted for in order to model and understand degradation mechanisms in fuel cells. While progress has been made in CFD-based modelling of fuel cells, functional and predictive capabilities remain a challenge because of fundamental modelling and material characterization deficiencies in ionic and water transport in polymer membranes; 2-phase transport in porous gas diffusion electrodes and gas flow channels; inadequate macroscopic modelling and resolution of catalyst

Economic dispatch optimization for system integrating renewable energy sources

Science.gov (United States)

Jihane, Kartite; Mohamed, Cherkaoui

2018-05-01

Nowadays, the use of energy is growing especially in transportation and electricity industries. However this energy is based on conventional sources which pollute the environment. Multi-source system is seen as the best solution to sustainable development. This paper proposes the Economic Dispatch (ED) of hybrid renewable power system. The hybrid system is composed of ten thermal generators, photovoltaic (PV) generator and wind turbine generator. To show the importance of renewable energy sources (RES) in the energy mix we have ran the simulation for system integrated PV only and PV plus wind. The result shows that the system with renewable energy sources (RES) is more compromising than the system without RES in terms of fuel cost.

Regulation on the transport of nuclear fuel materials by vehicles

International Nuclear Information System (INIS)

1984-01-01

The regulations applying to the transport of nuclear fuel materials by vehicles, mentioned in the law for the regulations of nuclear source materials, nuclear fuel materials and reactors. The transport is for outside of the factories and the site of enterprises by such modes of transport as rail, trucks, etc. Covered are the following: definitions of terms, places of fuel materials handling, loading methods, limitations on mix loading with other cargo, radiation dose rates concerning the containers and the vehicles, transport indexes, signs and indications, limitations on train linkage during transport by rail, security guards, transport of empty containers, etc. together with ordinary rail cargo and so on. (Mori, K.)

Fleet renewal: An approach to achieve sustainable road transport

Directory of Open Access Journals (Sweden)

Manojlović Aleksandar V.

2011-01-01

Full Text Available With more stringent requirements for efficient utilization of energy resources within the transport industry a need for implementation of sustainable development principles has appeared. Such action will be one of competitive advantages in the future. This is especially confirmed within the road transport sector. A methodology implemented in public procurement procedures for fleet renewal regarding the calculation of road vehicles’ operational lifecycle costs has been analyzed in detail in this paper. Afore mentioned calculation comprises the costs for: vehicle ownership, energy, carbon dioxide and pollutants emissions. Implementation of this methodology allows making the choice of energy efficient vehicles and vehicles with notable positive environmental effects. The objective of the research is to assess the influence of specific parameters of vehicle operational lifecycle costs, especially energy costs and estimated vehicle energy consumption, on vehicle choice in the procurement procedure. The case of urban bus fleet in Serbia was analyzed. Their operational lifecycle costs were calculated and differently powered vehicles were assessed. Energy consumption input values were defined. It was proved that defined fleet renewal scenarios could influence unquestionable decrease in energy consumption.

System and method for integration of renewable energy and fuel cell for the production of electricity and hydrogen

NARCIS (Netherlands)

Hemmes, K.

2007-01-01

The invention relates to a system and method for integrating renewable energy and a fuel cell for the production of electricity and hydrogen, wherein this comprises the use of renewable energy as fluctuating energy source for the production of electricity and also comprises the use of at least one

The renewable alternative

International Nuclear Information System (INIS)

Anon.

1992-01-01

This chapter discusses renewable energy sources as an alternative to a fossil fuel based economy. The topics discussed in the chapter include the historic aspects and current status of use of renewable energy, status of the renewable energy industry, market barriers to renewable energy, research and development and commercialization of renewable energy, the environmental and social costs associated with renewable energy, valuing future costs and benefits of energy use, and the potential market of renewable energy

A review of renewable energy in Canada, 1990-2003

International Nuclear Information System (INIS)

Nyboer, J.; Rivers, N.; Muncaster, K.; Bennett, M.; Bennett, S.

2004-10-01

This paper provides a comprehensive database of renewable energy facilities in Canada by province and by resource type. It considers technologies used for power generation or cogeneration, renewable energy heating systems, hydrogen generation and transportation fuels. Renewable energy technologies convert naturally regenerating resources into useful energy such as electricity, thermal energy, hydrogen or bio-fuels. The database contains information on renewable power operations in Canada over a scale of 100 kilowatts of rated capacity. Smaller applications have been included for run-of-river, hydro, earth, wind and solar power. There are 753 records for renewable energy facilities in Canada, including wind, hydroelectricity, wood residue biomass, landfill/sewage gas, solar photovoltaic, municipal solid waste, and tidal energy. The data in this report was acquired from Statistics Canada and other public information sources. For each of the 753 renewable energy power plants, this report states its type of renewable energy, the province, the name of the project, its location, its operator, electrical generating capacity, number of generating units, average annual electricity production, and the year it began operation. Canada currently has an installed electrical capacity of 115 GW, of which renewable energy sources constitute 76 per cent with the dominant source being hydroelectricity. Manitoba has the highest portion of renewable energy in its installed electrical capacity. Approximately 40 per cent Canada's renewable power capacity is in Quebec, followed by 15 per cent in British Columbia. Nova Scotia has Canada's only tidal power plant. Most of the installed renewable energy power capacity in Canada is owned by integrated electric utilities and a small percentage is owned by renewable electricity generating companies, aluminium companies, pulp and paper companies or diversified electricity generators. It is expected that interest in renewable energy will grow with

Fuel cell development for transportation: Catalyst development

Energy Technology Data Exchange (ETDEWEB)

Doddapaneni, N. [Sandia National Lab., Albuquerque, NM (United States)

1996-04-01

Fuel cells are being considered as alternate power sources for transportation and stationary applications. With proton exchange membrane (PEM) fuel cells the fuel crossover to cathodes causes severe thermal management and cell voltage drop due to oxidation of fuel at the platinized cathodes. The main goal of this project was to design, synthesize, and evaluate stable and inexpensive transition metal macrocyclic catalysts for the reduction of oxygen and be electrochemically inert towards anode fuels such as hydrogen and methanol.

Platinum Porous Electrodes for Fuel Cells

DEFF Research Database (Denmark)

Andersen, Shuang Ma

Fuel cell energy bears the merits of renewability, cleanness and high efficiency. Proton Exchange Membrane Fuel Cell (PEMFC) is one of the most promising candidates as the power source in the near future. A fine management of different transports and electrochemical reactions in PEM fuel cells...... to a genuine picture of a working PEM fuel cell catalyst layer. These, in turn, enrich the knowledge of Three-Phase-Boundary, provide efficient tool for the electrode selection and eventually will contribute the advancement of PEMFC technology....

Integration of carbon capture and sequestration and renewable resource technologies for sustainable energy supply in the transportation sector

International Nuclear Information System (INIS)

Kim, Minsoo; Won, Wangyun; Kim, Jiyong

2017-01-01

Highlights: • Integration of carbon capture and sequestration and renewable resource technologies. • A new superstructure-based optimization model to identify the energy supply system. • Model validation via application study of the future transportation sector in Korea. - Abstract: In this study, a new design for a sustainable energy system was developed by integrating two technology frameworks: the renewable resource-based energy supply and the conventional (fossil fuel) resource-based energy production coupled with carbon capture and sequestration. To achieve this goal, a new superstructure-based optimization model was proposed using mixed-integer linear programming to identify the optimal combination of these technologies that minimizes the total daily cost, subject to various practical and logical constraints. The performance of the proposed model was validated via an application study of the future transportation sector in Korea. By considering six different scenarios that combined varying crude oil/natural gas prices and environmental regulation options, the optimal configuration of the energy supply system was identified, and the major cost drivers and their sensitivities were analyzed. It was shown that conventional resource-based energy production was preferred if crude oil and natural gas prices were low, even though environmental regulation was considered. Environmental regulation caused an increase in the total daily cost by an average of 26.4%, mainly due to CO_2 capture cost.

World-wide French experience in research reactor fuel cycle transportation

International Nuclear Information System (INIS)

Raisonnier, D.

1997-01-01

Since 1963 Transnucleaire has safely performed a large number of national and international transports of radioactive material. Transnucleaire has also designed and supplied suitable packagings for all types of nuclear fuel cycle radioactive material from front-end and back-end products and for power or for research reactors. Transportation of the nuclear fuel material for power reactors is made on a regular and industrial basis. The transportation of material for the research reactor fuel cycle is quite different due to the small quantities involved, the categorisation of material and the numerous places of delivery world-wide. Adapted solutions exist, which require a reactive organisation dealing with all the transportation issues for LEU and HEU products as metal, oxide, fresh fuel elements, spent fuel elements including supply of necessary transport packaging and equipment. This presentation will: - explain the choices made by Transnucleaire and its associates to provide and optimise the corresponding services, - demonstrate the capability to achieve, through reliable partnership, transport operations involving new routes, specific equipment and new political constraints while respecting sophisticated safety and security regulations. (author)

The analysis of quantitative methods for renewable fuel processes and lubricant of materials derived from plastic waste

Science.gov (United States)

Rajagukguk, J. R.

2018-01-01

Plastic has become an important component in modern life today. Its role has replaced wood and metal, given its advantages such as light and strong, corrosion resistant, transparent and easy to color and good insulation properties. The research method is used with quantitative and engineering research methods. Research objective is to convert plastic waste into something more economical and to preserve the environment surrounding. Renewable fuel and lubricant variables are simultaneously influenced significantly to the sustainable environment. This is based on Fh> Ft of 62.101> 4.737) and its significance is 0.000 sustainable, the value of correlation coefficient 0.941 or 94.1% which means there is a very strong relationship between renewable fuel variables and lubricants to the sustainable environment. And utilizing plastic waste after being processed by pyrolysis method produces liquid hydrocarbons having elements of compounds such as crude oil and renewable fuels obtained from calculations are CO2 + H2O + C1-C4 + Residual substances. Then the plastic waste can be processed by isomerization process + catalyst to lubricating oil and the result of chemical calculation obtained is CO2, H2O, C18H21 and the rest.

Experience feedback from the transportation of Framatome fuel assemblies

International Nuclear Information System (INIS)

Robin, M.E.; Gaillard, G.; Aubin, C.

1998-01-01

Framatome, the foremost world nuclear fuel manufacturer, has for 25 years been delivering fuel elements from its three factories (Dessel, Romans, Pierrelatte) to the various sites in France and abroad (Germany, Sweden, Belgium, China, Korea, South Africa, Switzerland). During this period, Framatome has built up experience and expertise in fuel element transportation by road, rail and sea. In this filed, the range of constraints is very wide: safety and environmental protection constraints; constraints arising from the control and protection of nuclear materials, contractual and financial constraints, media watchdogs. Through the experience feedback from the transportation of FRAMATOME assemblies, this paper addresses all the phases in the transportation of fresh fuel assemblies. (authors)

Standardized, utility-DOE compatible, spent fuel storage-transport systems

International Nuclear Information System (INIS)

Smith, M.L.

1991-01-01

Virginia Power has developed and licensed a facility for dry storage of spent nuclear fuel in metal spent fuel storage casks. The modifications to the design of these casks necessary for licensing for both storage and transport of spent fuel are discussed along with the operational advantages of dual purpose storage-transport casks. Dual purpose casks can be used for storage at utility and DOE sites (MRS or repository) and for shipment between these sites with minimal spent fuel handling. The cost for a standardized system of casks that are compatible for use at both DOE and utility sites is discussed along with possible arrangements for sharing both the cost and benefits of dual purpose storage-transport casks

Renewable and dangerous residues as industrial fuels. Study about hard environmental support in the cement production in Brazil, years 1990

International Nuclear Information System (INIS)

Santi, Auxiliadora Maria Moura; Seva Filho, Arsenio Oswaldo

1999-01-01

The aim of the work is to indicate new fuels to Brazilian cement industry. A comparative study is presented. The renewable energetic sources, not renewable energetic sources, and residues of other industrial processes are analyzed

78 FR 69628 - Public Hearing for the 2014 Standards for the Renewable Fuel Standard Program

Science.gov (United States)

2013-11-20

..., biomass-based diesel, advanced biofuel, and renewable fuels that would apply to all gasoline and diesel produced in the U.S. or imported in the year 2014. In addition, the separate proposal includes a proposed...

Modeling the highway transportation of spent fuel

International Nuclear Information System (INIS)

Harrison, I.G.

1986-01-01

There will be a substantial increase in the number of spent fuel shipments on the nation's highway system in the next thirty years. Most of the spent fuel will be moving from reactors to a spent fuel repository. This study develops two models that evaluate the risk and cost of moving the spent fuel. The Minimum Total Transport Risk Model (MTTRM) seeks an efficient solution for this problem by finding the minimum risk path through the network and sending all the spent fuel shipments over this one path. The Equilibrium Transport Risk Model (ETRM) finds an equitable solution by distributing the shipments over a number of paths in the network. This model decreases the risk along individual paths, but increases society's risk because the spent fuel shipments are traveling over more links in the network. The study finds that there is a trade off between path risk and societal risk. As path risk declines, societal risk rises. The cost of shipping also increases as the number of paths expand. The cost and risk of shipping spent fuel from ten reactors to four potential repository sites are evaluated using the MTTRM. The temporary monitored retrievable storage (MRS) facility in Tennessee is found to be the minimum cost and minimum risk solution. When direct shipment to the permanent sites is considered, Deaf Smith, Texas is the least cost and least incident free transport risk location. Yucca Mountain, Nevada is the least risk location when the focus is placed on the potential consequences of an accident

Transportation of spent fuel from light water reactors

International Nuclear Information System (INIS)

Bernard, H.

1993-01-01

The French 'Compagnie Generale des Matieres Nucleaires' - COGEMA - is involved in the whole nuclear fuel cycle about 20 years. Among the different parts of the cycle, the Transport of Radioactive Materials, acting as a link between the differents plants has a great importance. As nuclear material transportation is the only fuel cycle step to be performed on public grounds, the industrial task has to be performed with the utmost stringent safety criteria. COGEMA and associates is now operating a fully mature commercial activity, with some 300 spent fuel shipments per year from its reprocessing customer's reactors to the LA HAGUE plant, either by rail, road or sea. The paper will review the organization of COGEMA transportation business, the level of technology with an update of the casks used for spent fuel, and the operational experience, with a particular view of the maintenance policy. (author)

Renewables in the Midwest

International Nuclear Information System (INIS)

Wager, J.S.

1994-01-01

Over the past three years, the Union of Concerned Scientists (UCS) has evaluated the potential for using renewable energy for electricity in the Midwest, and has been carrying out a multifaceted effort to expand the use of renewables in the region. The UCS study presents a strategy for developing renewable-electric technologies and resources in 12 midwestern states. UCS analysts used a geographic information system (GIS) to create data-bases of renewable resources, land uses, vegetation cover, terrain elevation and locations of utility transmission lines, and to analyze and present information on a .6 mi x .6 mi (1 km x 1 km) grid scale. In addition, UCS developed a model to calculate the net employment impact of renewable versus conventional electricity technologies on a state-by-state basis. In evaluating the costs and benefits of renewable energy sources, UCS analysts explored a cost assessment that accounted for the impact of pollution from fossil fuels on energy resource cost. Researchers also considered the risks associated with fuel-price volatility, environmental regulation, construction lead times and other uncertainties. Finally, UCS researchers suggested steps to remove the institutional, regulatory and legislative barriers that inhibit renewable energy development, and proposed policies to expand the use of the region's renewable resources. The UCS analysis showed that wind is currently the least expensive renewable resource. UCS also found numerous opportunities to expand biomass-electric generation in the near term, such as converting small coal-fired power plants to wood fuel, making greater use of logging residues and co-firing a small percentage of biomass with fossil fuel at large power plants

Biomass energy from wood chips: Diesel fuel dependence?

International Nuclear Information System (INIS)

Timmons, Dave; Mejia, Cesar Viteri

2010-01-01

Most renewable energy sources depend to some extent on use of other, non-renewable sources. In this study we explore use of diesel fuel in producing and transporting woody biomass in the state of New Hampshire, USA. We use two methods to estimate the diesel fuel used in woody biomass production: 1) a calculation based on case studies of diesel consumption in different parts of the wood chip supply chain, and 2) to support extrapolating those results to a regional system, an econometric study of the variation of wood-chip prices with respect to diesel fuel prices. The econometric study relies on an assumption of fixed demand, then assesses variables impacting supply, with a focus on how the price of diesel fuel affects price of biomass supplied. The two methods yield similar results. The econometric study, representing overall regional practices, suggests that a $1.00 per liter increase in diesel fuel price is associated with a $5.59 per Mg increase in the price of wood chips. On an energy basis, the diesel fuel used directly in wood chip production and transportation appears to account for less than 2% of the potential energy in the wood chips. Thus, the dependence of woody biomass energy production on diesel fuel does not appear to be extreme. (author)

Analysis Insights, August 2015: Sustainable Transportation; NREL (National Renewable Energy Laboratory)

Energy Technology Data Exchange (ETDEWEB)

None

2015-08-01

NREL Analysis Insights mines our body of analysis work to synthesize topical insights and key findings. In this issue, we examine transportation systems, alternative fuels, and implications of increasing electrification of transit. Moving people and goods from point A to B has never been easier, but our current transportation systems also take a toll on our environment. Transportation currently accounts for 71% of total U.S. petroleum use and 33% of the nation’s total carbon emissions. With new technology, can we make our transportation system cleaner and more cost effective? NREL is applying its analytical expertise and imagination to do just that. Solutions start with systems thinking. Connecting the dots between physical components - vehicles, fueling stations, and highways - and institutional components - traffic laws, regulations, and vehicle standards - helps illuminate solutions that address the needs of the transportation system's many stakeholders.

Integrated modeling for optimized regional transportation with compressed natural gas fuel

Directory of Open Access Journals (Sweden)

Hossam A. Gabbar

2016-03-01

Full Text Available Transportation represents major energy consumption where fuel is considered as a primary energy source. Recent development in the vehicle technology revealed possible economical improvements when using natural gas as a fuel source instead of traditional gasoline. There are several fuel alternatives such as electricity, which showed potential for future long-term transportation. However, the move from current situation where gasoline vehicle is dominating shows high cost compared to compressed natural gas vehicle. This paper presents modeling and simulation methodology to optimize performance of transportation based on quantitative study of the risk-based performance of regional transportation. Emission estimation method is demonstrated and used to optimize transportation strategies based on life cycle costing. Different fuel supply scenarios are synthesized and evaluated, which showed strategic use of natural gas as a fuel supply.

Beyond Solar Fuels: Renewable Energy-Driven Chemistry.

Science.gov (United States)

Lanzafame, Paola; Abate, Salvatare; Ampelli, Claudio; Genovese, Chiara; Passalacqua, Rosalba; Centi, Gabriele; Perathoner, Siglinda

2017-11-23

The future feasibility of decarbonized industrial chemical production based on the substitution of fossil feedstocks (FFs) with renewable energy (RE) sources is discussed. Indeed, the use of FFs as an energy source has the greatest impact on the greenhouse gas emissions of chemical production. This future scenario is indicated as "solar-driven" or "RE-driven" chemistry. Its possible implementation requires to go beyond the concept of solar fuels, in particular to address two key aspects: i) the use of RE-driven processes for the production of base raw materials, such as olefins, methanol, and ammonia, and ii) the development of novel RE-driven routes that simultaneously realize process and energy intensification, particularly in the direction of a significant reduction of the number of the process steps. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Building Partnerships to Cut Petroleum Use in Transportation

Energy Technology Data Exchange (ETDEWEB)

None

2014-02-26

The U.S. Department of Energy's Clean Cities initiative advances the nation's economic, environmental, and energy security by supporting local actions to cut petroleum use in transportation. Clean Cities accomplishes this work through the activities of nearly 100 local coalitions. These coalitions provide resources and technical assistance in the deployment of alternative and renewable fuels, idle-reduction measures, fuel economy improvements, and new transportation technologies as they emerge.

Market analysis. Renewable fuels

International Nuclear Information System (INIS)

2014-01-01

The Agency for Renewable Resources (FNR) had on behalf of the Federal Ministry of Food and Agriculture created a study on the market development of renewable resources in Germany and published this in the year of 2006. The aim of that study was to identify of actual status and market performance of the individual market segments of the material and energetic use as a basis for policy recommendations for accelerated and long term successful market launch and market share expansion of renewable raw materials. On behalf of the FNR, a market analysis of mid-2011 was carried out until the beginning of 2013, the results of which are hereby resubmitted. This market analysis covers all markets of material and energetic use in the global context, taking account of possible competing uses. A market segmentation, which was based on the product classification of the Federal Statistical Office, formed the basis of the analysis. A total of ten markets have been defined, seven material and three energetic use. [de

Terminology used for renewable liquid and gaseous fuels based on the conversion of electricity

DEFF Research Database (Denmark)

Ridjan, Iva; Mathiesen, Brian Vad; Connolly, David

2016-01-01

fuels produced with coal-, gas- and biomass-to-liquid (xTL) technologies. However, a number of articles use the term beyond this definition. Results for the term electrofuel gave a similar outcome, as it was not clear which processes were used for the fuel production. In some cases, both synthetic...... of this article is to identify and review these terms to avoid any potential misuse. An integrative review of terminology has been made. This review did not differentiate the articles in terms of the methodologies applied, but had the main objective to identify the terminology used and its definition. The results...... confirm that the term synthetic fuel is used generically in the majority of articles, without providing information about the production process of the fuel or differentiating between fossil-based and renewable-based synthetic fuels. The majority of the articles use the term synthetic fuel to describe...

10 CFR 490.203 - Light Duty Alternative Fueled Vehicle Plan.

Science.gov (United States)

2010-01-01

... Efficiency and Renewable Energy, EE-33, 1000 Independence Ave., SW., Washington, DC 20585, or to such other... 10 Energy 3 2010-01-01 2010-01-01 false Light Duty Alternative Fueled Vehicle Plan. 490.203 Section 490.203 Energy DEPARTMENT OF ENERGY ENERGY CONSERVATION ALTERNATIVE FUEL TRANSPORTATION PROGRAM...

INTERACTION OF AIR TRANSPORTATION AND FUEL-SUPPLY COMPANIES

Directory of Open Access Journals (Sweden)

I. P. Zheleznaya

2014-01-01

Full Text Available The article describes the role of aviation fuel in the life of air transport. Fueling industry worldwide solves two main tasks - ensuring the safety and economy of air traffic. In Russia, there is one more task of airlines fuel supply. The article deals with fuel pricing taking into consideration today's realities.

An Indian perspective for transportation and storage of spent fuel

International Nuclear Information System (INIS)

Dey, P.K.

2005-01-01

The spent fuel discharged from the reactors are temporarily stored at the reactor pool. After a certain cooling time, the spent fuel is moved to the storage locations either on or off reactor site depending on the spent fuel management strategy. As India has opted for a closed fuel cycle for its nuclear energy development, reprocessing of the spent fuel, recycling of the reprocessed plutonium and uranium and disposal of the wastes from the reprocessing operations forms the spent fuel management strategy. Since the reprocessing operations are planned to match the nuclear energy programme, storage of the spent fuel in ponds are adopted prior to reprocessing. Transport of the spent fuel to the storage locations are carried out adhering to international and national guide lines. India is having 14 operating power reactors and three research reactors. The spent fuel from the two safeguarded BWRs are stored at-reactor (AR) storage pond. A separate wet storage facility away-from-reactor (AFR) has been designed, constructed and made operational since 1991 for additional fuel storage. Storage facilities are provided in ARs at other reactor locations to cater to 10 reactor-years of operation. A much lower capacity spent fuel storage is provided in reprocessing plants on the same lines of AR fuel storage design. Since the reprocessing operations are carried out on a need basis, to cater to the increased storage needs two new spent fuel storage facilities (SFSF) are being designed and constructed near the existing nuclear plant sites. India has mastered the technology for design, construction and operation of wet spent fuel storage facility meeting all the international standards Wet storage of the spent fuel is the most commonly adopted mode all over the world. Recently an alternate mode viz. dry storage has also been considered. India has designed, constructed and operated lead shielded dry storage casks and is operational at one site. A dry storage cask made of concrete

The interaction between intermittent renewable energy and the electricity, heating and transport sectors

DEFF Research Database (Denmark)

Mathiesen, Brian Vad; Duić, Neven; Stadler, Ingo

2012-01-01

In a global perspective, it is essential that the world transfers from fossil fuels to renewable energy sources in order to minimise climate change effects. As a part of such transition energy savings are also important, as they can decrease production costs effectively. The nature of such a change...

World Biofuels Production Potential Understanding the Challenges to Meeting the U.S. Renewable Fuel Standard

Energy Technology Data Exchange (ETDEWEB)

Sastri, B.; Lee, A.

2008-09-15

This study by the U.S. Department of Energy (DOE) estimates the worldwide potential to produce biofuels including biofuels for export. It was undertaken to improve our understanding of the potential for imported biofuels to satisfy the requirements of Title II of the 2007 Energy Independence and Security Act (EISA) in the coming decades. Many other countries biofuels production and policies are expanding as rapidly as ours. Therefore, we modeled a detailed and up-to-date representation of the amount of biofuel feedstocks that are being and can be grown, current and future biofuels production capacity, and other factors relevant to the economic competitiveness of worldwide biofuels production, use, and trade. The Oak Ridge National Laboratory (ORNL) identified and prepared feedstock data for countries that were likely to be significant exporters of biofuels to the U.S. The National Renewable Energy Laboratory (NREL) calculated conversion costs by conducting material flow analyses and technology assessments on biofuels technologies. Brookhaven National Laboratory (BNL) integrated the country specific feedstock estimates and conversion costs into the global Energy Technology Perspectives (ETP) MARKAL (MARKet ALlocation) model. The model uses least-cost optimization to project the future state of the global energy system in five year increments. World biofuels production was assessed over the 2010 to 2030 timeframe using scenarios covering a range U.S. policies (tax credits, tariffs, and regulations), as well as oil prices, feedstock availability, and a global CO{sub 2} price. All scenarios include the full implementation of existing U.S. and selected other countries biofuels policies (Table 4). For the U.S., the most important policy is the EISA Title II Renewable Fuel Standard (RFS). It progressively increases the required volumes of renewable fuel used in motor vehicles (Appendix B). The RFS requires 36 billion (B) gallons (gal) per year of renewable fuels by 2022

Proceedings of the 2008 transportation technologies and fuels forum

International Nuclear Information System (INIS)

2008-01-01

As a large emitter of pollutants, the transportation industry is now seeking to develop a sustainable transportation plan for the future by developing methods of reducing emissions and improving the fuel efficiency of vehicles. This forum discussed recent innovations in vehicle transportation technologies. Industry leaders, government representatives, and researchers discussed methods of reducing greenhouse gases (GHGs) and air pollution in the transportation sector. Advanced combustion technologies were outlined, and recent developments in hybrid electric-powered vehicles were discussed. Research related to fuel cells, hydrogen fuels and biofuels was presented. The impacts of polluting vehicles on public health were also discussed. The forum was divided into the following 5 sessions: (1) setting the scene, (2) future fuels, (3) emissions, (4) EVs now, and (5) the road to the future. The sessions were followed by a panel on technology roadmaps. The forum featured 14 presentations, of which 4 have been catalogued separately for inclusion in this database. tabs., figs.

Drop analysis for structural integrity evaluation of KJRR fuel transport container

International Nuclear Information System (INIS)

Yang, Yun Young; Lim, Jong Min; Choi, Woo Seok; Lee, Ju Chan

2016-01-01

A fuel transport container for KiJang Research Reactor(KJRR) has been developed to transport fresh fuel assemblies and fission molly targets which are used for a research reactor built in Kijang. The KJRR fuel transport container is a type-A(F) container, which is defined in domestic and foreign regulations of a radioactive substance container. According to Nuclear Safety and Security Commission's notification, the container should meet the accident conditions defined in IAEA safety Standard Series, US NRC and etc. In this study, a structural integrity of the KJRR fuel transport container is evaluated by conducting computational analyses of 9-meter free drop and 1 meter puncture. It is confirmed that structural integrity of the KJRR fuel transport container can be maintained in the transportation accident condition. Hereafter, when the test model is produced, a safety test will be conducted and its result will be compared with the result of drop and puncture analyses.

Numerical simulation of ion transport membrane reactors: Oxygen permeation and transport and fuel conversion

KAUST Repository

Hong, Jongsup; Kirchen, Patrick; Ghoniem, Ahmed F.

2012-01-01

Ion transport membrane (ITM) based reactors have been suggested as a novel technology for several applications including fuel reforming and oxy-fuel combustion, which integrates air separation and fuel conversion while reducing complexity

Spent fuel transportation in the United States: commercial spent fuel shipments through December 1984

International Nuclear Information System (INIS)

1986-04-01

This report has been prepared to provide updated transportation information on light water reactor (LWR) spent fuel in the United States. Historical data are presented on the quantities of spent fuel shipped from individual reactors on an annual basis and their shipping destinations. Specifically, a tabulation is provided for each present-fuel shipment that lists utility and plant of origin, destination and number of spent-fuel assemblies shipped. For all annual shipping campaigns between 1980 and 1984, the actual numbers of spent-fuel shipments are defined. The shipments are tabulated by year, and the mode of shipment and the casks utilized in shipment are included. The data consist of the current spent-fuel inventories at each of the operating reactors as of December 31, 1984. This report presents historical data on all commercial spent-fuel transportation shipments have occurred in the United States through December 31, 1984

Marginal abatement cost curve for nitrogen oxides incorporating controls, renewable electricity, energy efficiency, and fuel switching.

Science.gov (United States)