WorldWideScience

Sample records for renewable surface separations

  1. Computational efficiency for the surface renewal method

    Science.gov (United States)

    Kelley, Jason; Higgins, Chad

    2018-04-01

    Measuring surface fluxes using the surface renewal (SR) method requires programmatic algorithms for tabulation, algebraic calculation, and data quality control. A number of different methods have been published describing automated calibration of SR parameters. Because the SR method utilizes high-frequency (10 Hz+) measurements, some steps in the flux calculation are computationally expensive, especially when automating SR to perform many iterations of these calculations. Several new algorithms were written that perform the required calculations more efficiently and rapidly, and that tested for sensitivity to length of flux averaging period, ability to measure over a large range of lag timescales, and overall computational efficiency. These algorithms utilize signal processing techniques and algebraic simplifications that demonstrate simple modifications that dramatically improve computational efficiency. The results here complement efforts by other authors to standardize a robust and accurate computational SR method. Increased speed of computation time grants flexibility to implementing the SR method, opening new avenues for SR to be used in research, for applied monitoring, and in novel field deployments.

  2. SURFACE ENERGY BALANCE OVER ORANGE ORCHARD USING SURFACE RENEWAL ANALYSIS

    Directory of Open Access Journals (Sweden)

    Salvatore Barbagallo

    2009-12-01

    Full Text Available Reliable estimation of surface sensible and latent heat flux is the most important process to appraise energy and mass exchange among atmosphere and biosphere. In this study the surface energy fluxes were measured over an irrigated orange orchard during 2005-2008 monitoring periods using a Surface Renewal- Energy Balance approach. The experimental area is located in a representative orchard growing area of eastern Sicily (Italy. The performance of Surface Renewal (SR analysis for estimating sensible heat flux (H was analysed and evaluated in terms of correlation with H fluxes from the eddy covariance (EC method. Study revealed that the mean available energy (RN- G and latent heat flux (LE were of about 300 W m-2 and 237 W m-2, respectively, during dry periods and unstable-case atmospheric conditions. The estimated crop coefficient Kc values for the orchard crop averaged close to 0.80, which is considerably higher than previous FAO studies that found the value to be 0.65 for citrus with 70% of ground cover. The intercepted photosynthetically active radiation (LI PAR by the crop was measured and relationships between LAI and crop coefficient (Kc were established.

  3. Surface renewal as a significant mechanism for dust emission

    Directory of Open Access Journals (Sweden)

    J. Zhang

    2016-12-01

    Full Text Available Wind tunnel experiments of dust emissions from different soil surfaces are carried out to better understand dust emission mechanisms. The effects of surface renewal on aerodynamic entrainment and saltation bombardment are analyzed in detail. It is found that flow conditions, surface particle motions (saltation and creep, soil dust content and ground obstacles all strongly affect dust emission, causing its rate to vary over orders of magnitude. Aerodynamic entrainment is highly effective, if dust supply is unlimited, as in the first 2–3 min of our wind tunnel runs. While aerodynamic entrainment is suppressed by dust supply limits, surface renewal through the motion of surface particles appears to be an effective pathway to remove the supply limit. Surface renewal is also found to be important to the efficiency of saltation bombardment. We demonstrate that surface renewal is a significant mechanism affecting dust emission and recommend that this mechanism be included in future dust models.

  4. Sound field separation with cross measurement surfaces.

    Directory of Open Access Journals (Sweden)

    Jin Mao

    Full Text Available With conventional near-field acoustical holography, it is impossible to identify sound pressure when the coherent sound sources are located on the same side of the array. This paper proposes a solution, using cross measurement surfaces to separate the sources based on the equivalent source method. Each equivalent source surface is built in the center of the corresponding original source with a spherical surface. According to the different transfer matrices between equivalent sources and points on holographic surfaces, the weighting of each equivalent source from coherent sources can be obtained. Numerical and experimental studies have been performed to test the method. For the sound pressure including noise after separation in the experiment, the calculation accuracy can be improved by reconstructing the pressure with Tikhonov regularization and the L-curve method. On the whole, a single source can be effectively separated from coherent sources using cross measurement.

  5. Advances in the Surface Renewal Flux Measurement Method

    Science.gov (United States)

    Shapland, T. M.; McElrone, A.; Paw U, K. T.; Snyder, R. L.

    2011-12-01

    The measurement of ecosystem-scale energy and mass fluxes between the planetary surface and the atmosphere is crucial for understanding geophysical processes. Surface renewal is a flux measurement technique based on analyzing the turbulent coherent structures that interact with the surface. It is a less expensive technique because it does not require fast-response velocity measurements, but only a fast-response scalar measurement. It is therefore also a useful tool for the study of the global cycling of trace gases. Currently, surface renewal requires calibration against another flux measurement technique, such as eddy covariance, to account for the linear bias of its measurements. We present two advances in the surface renewal theory and methodology that bring the technique closer to becoming a fully independent flux measurement method. The first advance develops the theory of turbulent coherent structure transport associated with the different scales of coherent structures. A novel method was developed for identifying the scalar change rate within structures at different scales. Our results suggest that for canopies less than one meter in height, the second smallest coherent structure scale dominates the energy and mass flux process. Using the method for resolving the scalar exchange rate of the second smallest coherent structure scale, calibration is unnecessary for surface renewal measurements over short canopies. This study forms the foundation for analysis over more complex surfaces. The second advance is a sensor frequency response correction for measuring the sensible heat flux via surface renewal. Inexpensive fine-wire thermocouples are frequently used to record high frequency temperature data in the surface renewal technique. The sensible heat flux is used in conjunction with net radiation and ground heat flux measurements to determine the latent heat flux as the energy balance residual. The robust thermocouples commonly used in field experiments

  6. A surface-renewal model of cross-flow microfiltration

    Directory of Open Access Journals (Sweden)

    A. Hasan

    2013-03-01

    Full Text Available A mathematical model using classical cake-filtration theory and the surface-renewal concept is formulated for describing cross-flow microfiltration under dynamic and steady-state conditions. The model can predict the permeate flux and cake buildup in the filter. The three basic parameters of the model are the membrane resistance, specific cake resistance and rate of surface renewal. The model is able to correlate experimental permeate flow rate data in the microfiltration of fermentation broths in laboratory- and pilot-scale units with an average root-mean-square (RMS error of 4.6%. The experimental data are also compared against the critical-flux model of cross-flow microfiltration, which has average RMS errors of 6.3, 5.5 and 6.1% for the cases of cake filtration, intermediate blocking and complete blocking mechanisms, respectively.

  7. Surface renewal analysis for estimating turbulent surface fluxes

    International Nuclear Information System (INIS)

    Castellvi, F.

    2009-01-01

    A decade ago, the need for a long-term surface monitoring was recognized to better understand the soil-vegetation-atmosphere scalar exchange and interaction processes. the AmeriFlux concept emerged in the IGBP workshop (La Thuile, IT, 1995). Continuous acquisition of surface fluxes for different species such as temperature, water vapour, CO x , halocarbon, ozone, etc.,) and momentum allows determination of the influence of local (canopy) exchanges, fossil fuel emission, large-scale biotic exchange on ambient concentrations which are crucial to take decisions for protecting natural environments and water resources, to develop new perspective for modern agriculture and forest management and to better understand the global climate change. (Author)

  8. Renewable and superior thermal-resistant cellulose-based composite nonwoven as lithium-ion battery separator.

    Science.gov (United States)

    Zhang, Jianjun; Liu, Zhihong; Kong, Qingshan; Zhang, Chuanjian; Pang, Shuping; Yue, Liping; Wang, Xuejiang; Yao, Jianhua; Cui, Guanglei

    2013-01-01

    A renewable and superior thermal-resistant cellulose-based composite nonwoven was explored as lithium-ion battery separator via an electrospinning technique followed by a dip-coating process. It was demonstrated that such nanofibrous composite nonwoven possessed good electrolyte wettability, excellent heat tolerance, and high ionic conductivity. The cells using the composite separator displayed better rate capability and enhanced capacity retention, when compared to those of commercialized polypropylene separator under the same conditions. These fascinating characteristics would endow this renewable composite nonwoven a promising separator for high-power lithium-ion battery.

  9. Surface Renewal Application for Estimating Evapotranspiration: A Review

    Directory of Open Access Journals (Sweden)

    Yongguang Hu

    2018-01-01

    Full Text Available The estimation of evapotranspiration (ET is essential for meteorological modeling of surface exchange processes, as well as for the agricultural practice of irrigation management. Hitherto, a number of methods for estimation of ET at different temporal scales and climatic conditions are constantly under investigation and improvement. One of these methods is surface renewal (SR. Therefore, the premise of this review is to present recent developments and applications of SR for ET measurements. The SR method is based on estimating the turbulent exchange of sensible heat flux between plant canopy and atmosphere caused by the instantaneous replacement of air parcels in contact with the surface. Additional measurements of net radiation and soil heat flux facilitate extracting ET using the shortened energy balance equation. The challenge, however, is the calibration of SR results against direct sensible heat flux measurements. For the classical SR method, only air temperature measured at high frequency is required. In addition, a new model suggests that the SR method could be exempted from calibration by measuring additional micrometeorological variables. However, further improvement of the SR method is required to provide improved results in the future.

  10. Estimation of sensible and latent heat flux from natural sparse vegetation surfaces using surface renewal

    Science.gov (United States)

    Zapata, N.; Martínez-Cob, A.

    2001-12-01

    This paper reports a study undertaken to evaluate the feasibility of the surface renewal method to accurately estimate long-term evaporation from the playa and margins of an endorreic salty lagoon (Gallocanta lagoon, Spain) under semiarid conditions. High-frequency temperature readings were taken for two time lags ( r) and three measurement heights ( z) in order to get surface renewal sensible heat flux ( HSR) values. These values were compared against eddy covariance sensible heat flux ( HEC) values for a calibration period (25-30 July 2000). Error analysis statistics (index of agreement, IA; root mean square error, RMSE; and systematic mean square error, MSEs) showed that the agreement between HSR and HEC improved as measurement height decreased and time lag increased. Calibration factors α were obtained for all analyzed cases. The best results were obtained for the z=0.9 m ( r=0.75 s) case for which α=1.0 was observed. In this case, uncertainty was about 10% in terms of relative error ( RE). Latent heat flux values were obtained by solving the energy balance equation for both the surface renewal ( LESR) and the eddy covariance ( LEEC) methods, using HSR and HEC, respectively, and measurements of net radiation and soil heat flux. For the calibration period, error analysis statistics for LESR were quite similar to those for HSR, although errors were mostly at random. LESR uncertainty was less than 9%. Calibration factors were applied for a validation data subset (30 July-4 August 2000) for which meteorological conditions were somewhat different (higher temperatures and wind speed and lower solar and net radiation). Error analysis statistics for both HSR and LESR were quite good for all cases showing the goodness of the calibration factors. Nevertheless, the results obtained for the z=0.9 m ( r=0.75 s) case were still the best ones.

  11. Microphase separated structure and surface properties of fluorinated polyurethane resin

    International Nuclear Information System (INIS)

    Sudaryanto; Nishino, T.; Hori, Y.; Nakamae, K.

    2000-01-01

    The effect of fluorination on microphase separation and surface properties of segmented polyurethane (PU) resin were investigated. A series of fluorinated polyurethane resin (FPU) was synthesized by reacting a fluorinated diol with aromatic diisocyanate. The microphase separated structure of FPU was studied by thermal analysis, and small angle X-ray scattering (SAXS) as well as wide angle X-ray diffraction (WAXD). The surface structure and properties were characterized by X-ray photoelectron spectroscopy (XPS) and dynamic contact angle measurement. The incorporation of fluorine into hard segment brings the FPU to have a higher hard domain cohesion and increase the phase separation, however localization of fluorine on the surface could not be observed. On the other hands, localization of fluorine on the surface could be achieved for soft segment fluorinated PU without any significant change in microphase separated structure. The result from this study give an important basic information for designing PU coating material with a low surface energy and strong adhesion as well as for development of release film on pressure sensitive adhesive tape. (author)

  12. Particle separation by phase modulated surface acoustic waves.

    Science.gov (United States)

    Simon, Gergely; Andrade, Marco A B; Reboud, Julien; Marques-Hueso, Jose; Desmulliez, Marc P Y; Cooper, Jonathan M; Riehle, Mathis O; Bernassau, Anne L

    2017-09-01

    High efficiency isolation of cells or particles from a heterogeneous mixture is a critical processing step in lab-on-a-chip devices. Acoustic techniques offer contactless and label-free manipulation, preserve viability of biological cells, and provide versatility as the applied electrical signal can be adapted to various scenarios. Conventional acoustic separation methods use time-of-flight and achieve separation up to distances of quarter wavelength with limited separation power due to slow gradients in the force. The method proposed here allows separation by half of the wavelength and can be extended by repeating the modulation pattern and can ensure maximum force acting on the particles. In this work, we propose an optimised phase modulation scheme for particle separation in a surface acoustic wave microfluidic device. An expression for the acoustic radiation force arising from the interaction between acoustic waves in the fluid was derived. We demonstrated, for the first time, that the expression of the acoustic radiation force differs in surface acoustic wave and bulk devices, due to the presence of a geometric scaling factor. Two phase modulation schemes are investigated theoretically and experimentally. Theoretical findings were experimentally validated for different mixtures of polystyrene particles confirming that the method offers high selectivity. A Monte-Carlo simulation enabled us to assess performance in real situations, including the effects of particle size variation and non-uniform acoustic field on sorting efficiency and purity, validating the ability to separate particles with high purity and high resolution.

  13. Radio-iodinated surface proteins of electrophoretically separated rat lymphocytes

    International Nuclear Information System (INIS)

    Jilg, W.; Hannig, K.; Zeiller, K.

    1980-01-01

    Rat thymocytes and lymph node cells were separated into three T and one B subpopulation by means of free flow electrophoresis. The surface proteins of the separated cells were labelled by lactoperoxidase catalysed radioiodination. Most of the label was demonstrated to be at the cell surface. Although the surface protein patterns of the four lamphocyte subpopulations were rather similar, distinctive differences could be found. B cells had six labelled proteins which seemed to be absent in the other cells. In the T cell group three protein bands were identified, each with specificity for peripheral T cells, thymocytes and all T cells respectively. Four other proteins were found which showed quantitative differences between the four cell groups. (orig.) [de

  14. Texture segregation, surface representation and figure-ground separation.

    Science.gov (United States)

    Grossberg, S; Pessoa, L

    1998-09-01

    A widespread view is that most texture segregation can be accounted for by differences in the spatial frequency content of texture regions. Evidence from both psychophysical and physiological studies indicate, however, that beyond these early filtering stages, there are stages of 3-D boundary segmentation and surface representation that are used to segregate textures. Chromatic segregation of element-arrangement patterns--as studied by Beck and colleagues--cannot be completely explained by the filtering mechanisms previously employed to account for achromatic segregation. An element arrangement pattern is composed of two types of elements that are arranged differently in different image regions (e.g. vertically on top and diagonally on the bottom). FACADE theory mechanisms that have previously been used to explain data about 3-D vision and figure-ground separation are here used to simulate chromatic texture segregation data, including data with equiluminant elements on dark or light homogeneous backgrounds, or backgrounds composed of vertical and horizontal dark or light stripes, or horizontal notched stripes. These data include the fact that segregation of patterns composed of red and blue squares decreases with increasing luminance of the interspaces. Asymmetric segregation properties under 3-D viewing conditions with the equiluminant elements close or far are also simulated. Two key model properties are a spatial impenetrability property that inhibits boundary grouping across regions with non-collinear texture elements and a boundary-surface consistency property that uses feedback between boundary and surface representations to eliminate spurious boundary groupings and separate figures from their backgrounds.

  15. Integral methods for shallow free-surface flows with separation

    DEFF Research Database (Denmark)

    Watanabe, S.; Putkaradze, V.; Bohr, Tomas

    2003-01-01

    eddy and separated flow. Assuming a variable radial velocity profile as in Karman-Pohlhausen's method, we obtain a system of two ordinary differential equations for stationary states that can smoothly go through the jump. Solutions of the system are in good agreement with experiments. For the flow down...... an inclined plane we take a similar approach and derive a simple model in which the velocity profile is not restricted to a parabolic or self-similar form. Two types of solutions with large surface distortions are found: solitary, kink-like propagating fronts, obtained when the flow rate is suddenly changed......, and stationary jumps, obtained, for instance, behind a sluice gate. We then include time dependence in the model to study the stability of these waves. This allows us to distinguish between sub- and supercritical flows by calculating dispersion relations for wavelengths of the order of the width of the layer....

  16. Advancing the Frontiers in Nanocatalysis, Biointerfaces, and Renewable Energy Conversion by Innovations of Surface Techniques

    Energy Technology Data Exchange (ETDEWEB)

    Somorjai, G.A.; Frei, H.; Park, J.Y.

    2009-07-23

    The challenge of chemistry in the 21st century is to achieve 100% selectivity of the desired product molecule in multipath reactions ('green chemistry') and develop renewable energy based processes. Surface chemistry and catalysis play key roles in this enterprise. Development of in situ surface techniques such as high-pressure scanning tunneling microscopy, sum frequency generation (SFG) vibrational spectroscopy, time-resolved Fourier transform infrared methods, and ambient pressure X-ray photoelectron spectroscopy enabled the rapid advancement of three fields: nanocatalysts, biointerfaces, and renewable energy conversion chemistry. In materials nanoscience, synthetic methods have been developed to produce monodisperse metal and oxide nanoparticles (NPs) in the 0.8-10 nm range with controlled shape, oxidation states, and composition; these NPs can be used as selective catalysts since chemical selectivity appears to be dependent on all of these experimental parameters. New spectroscopic and microscopic techniques have been developed that operate under reaction conditions and reveal the dynamic change of molecular structure of catalysts and adsorbed molecules as the reactions proceed with changes in reaction intermediates, catalyst composition, and oxidation states. SFG vibrational spectroscopy detects amino acids, peptides, and proteins adsorbed at hydrophobic and hydrophilic interfaces and monitors the change of surface structure and interactions with coadsorbed water. Exothermic reactions and photons generate hot electrons in metal NPs that may be utilized in chemical energy conversion. The photosplitting of water and carbon dioxide, an important research direction in renewable energy conversion, is discussed.

  17. Super-virtual Interferometric Separation and Enhancement of Back-scattered Surface Waves

    KAUST Repository

    Guo, Bowen; Hanafy, Sherif; Schuster, Gerard T.

    2015-01-01

    Back-scattered surface waves can be migrated to detect near-surface reflectors with steep dips. A robust surface-wave migration requires the prior separation of the back-scattered surface-wave events from the data. This separation is often difficult

  18. Plasma-Assisted Synthesis and Surface Modification of Electrode Materials for Renewable Energy.

    Science.gov (United States)

    Dou, Shuo; Tao, Li; Wang, Ruilun; El Hankari, Samir; Chen, Ru; Wang, Shuangyin

    2018-02-14

    Renewable energy technology has been considered as a "MUST" option to lower the use of fossil fuels for industry and daily life. Designing critical and sophisticated materials is of great importance in order to realize high-performance energy technology. Typically, efficient synthesis and soft surface modification of nanomaterials are important for energy technology. Therefore, there are increasing demands on the rational design of efficient electrocatalysts or electrode materials, which are the key for scalable and practical electrochemical energy devices. Nevertheless, the development of versatile and cheap strategies is one of the main challenges to achieve the aforementioned goals. Accordingly, plasma technology has recently appeared as an extremely promising alternative for the synthesis and surface modification of nanomaterials for electrochemical devices. Here, the recent progress on the development of nonthermal plasma technology is highlighted for the synthesis and surface modification of advanced electrode materials for renewable energy technology including electrocatalysts for fuel cells, water splitting, metal-air batteries, and electrode materials for batteries and supercapacitors, etc. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  19. Super-virtual Interferometric Separation and Enhancement of Back-scattered Surface Waves

    KAUST Repository

    Guo, Bowen

    2015-08-19

    Back-scattered surface waves can be migrated to detect near-surface reflectors with steep dips. A robust surface-wave migration requires the prior separation of the back-scattered surface-wave events from the data. This separation is often difficult to implement because the back-scattered surface waves are masked by the incident surface waves. We mitigate this problem by using a super-virtual interferometric method to enhance and separate the back-scattered surface waves. The key idea is to calculate the virtual back-scattered surface waves by stacking the resulting virtual correlated and convolved traces associated with the incident and back-scattered waves. Stacking the virtual back-scattered surface waves improves their signal-to-noise ratio and separates the back-scattered surface-waves from the incident field. Both synthetic and field data results validate the robustness of this method.

  20. Measurement of near neighbor separations of surface atoms

    International Nuclear Information System (INIS)

    Cohen, P.I.

    Two techniques are being developed to measure the nearest neighbor distances of atoms at the surfaces of solids. Both measures extended fine structure in the excitation probability of core level electrons which are excited by an incident electron beam. This is an important problem because the structures of most surface systems are as yet unknown, even though the location of surface atoms is the basis for any quantitative understanding of the chemistry and physics of surfaces and interfaces. These methods would allow any laboratory to make in situ determinations of surface structure in conjunction with most other laboratory probes of surfaces. Each of these two techniques has different advantages; further, the combination of the two will increase confidence in the results by reducing systematic error in the data analysis

  1. Dual-band frequency selective surface with large band separation and stable performance

    Science.gov (United States)

    Zhou, Hang; Qu, Shao-Bo; Peng, Wei-Dong; Lin, Bao-Qin; Wang, Jia-Fu; Ma, Hua; Zhang, Jie-Qiu; Bai, Peng; Wang, Xu-Hua; Xu, Zhuo

    2012-05-01

    A new technique of designing a dual-band frequency selective surface with large band separation is presented. This technique is based on a delicately designed topology of L- and Ku-band microwave filters. The two band-pass responses are generated by a capacitively-loaded square-loop frequency selective surface and an aperture-coupled frequency selective surface, respectively. A Faraday cage is located between the two frequency selective surface structures to eliminate undesired couplings. Based on this technique, a dual-band frequency selective surface with large band separation is designed, which possesses large band separation, high selectivity, and stable performance under various incident angles and different polarizations.

  2. Particle separation by external fields on periodic surfaces

    International Nuclear Information System (INIS)

    Sancho, J M; Khoury, M; Lindenberg, K; Lacasta, A M

    2005-01-01

    Particles moving on perfect periodic surfaces under the influence of external forces may move along directions that deviate from that of the force. We briefly recall previous results for transport of particles on surfaces with periodic traps or periodic obstacles driven by a constant external force, and present new results for particles moving in a harmonic periodic potential. The sorting properties are explored as a function of a number of control parameters, specifically the friction, force amplitude and direction, temperature, and lattice constants

  3. [Studies on a sequential injection renewable surface reflectance spectrophotometric system using a microchip flow cell].

    Science.gov (United States)

    Wang, Jian-ya; Fang, Zhao-lun

    2002-02-01

    A microchip flow cell was developed for flow injection renewable surface assay by reflectance spectrophotometry. The flow cell was coupled to a sequential injection system and optical fiber photometric detection system. The flow cell featured a three-layer structure. The flow channel was cut into a silicone rubber membrance which formed the middle layer, and a porous filter was inlayed across a widened section of the channel to trap microbeads introduced into the flow cell. The area of the detection window of the flow cell was approximately 3.6 mm2, the volume of the bead trapped in the flow cell was 2.2 microL, the depth of the bead layer was 600 microns. A multistrand bifurcated optical fiber was coupled with incident light, detector and flow cell. The chromogenic reaction of Cr(VI) with 1,5-diphenylcarbohydrazide (DPC) which was adsorbed on trapped Polysorb C-18 beads was used as a model reaction to optimize the flow cell design and the experimental system. The reflectance of the renewable reaction surface was monitored at 540 nm. With 100 microL sample loaded and 1.0 mL.min-1 carrier flow rate, the linear response range was 0-0.6 microgram.mL-1 Cr(VI). A detection limit (3 sigma) of 6 ng.mL-1, precision of 1.5% RSD(n = 11), and a throughput of 64 samples per hour were achieved. Considerations in system and flow cell design, the influence of depth of the bead layer, weight of beads used, and the flow rates of carrier stream on the performance were discussed.

  4. Atmospheric-pressure plasma activation and surface characterization on polyethylene membrane separator

    Science.gov (United States)

    Tseng, Yu-Chien; Li, Hsiao-Ling; Huang, Chun

    2017-01-01

    The surface hydrophilic activation of a polyethylene membrane separator was achieved using an atmospheric-pressure plasma jet. The surface of the atmospheric-pressure-plasma-treated membrane separator was found to be highly hydrophilic realized by adjusting the plasma power input. The variations in membrane separator chemical structure were confirmed by Fourier transform infrared spectroscopy and X-ray photoelectron spectroscopy. Chemical analysis showed newly formed carbonyl-containing groups and high surface concentrations of oxygen-containing species on the atmospheric-pressure-plasma-treated polymeric separator surface. It also showed that surface hydrophilicity primarily increased from the polar component after atmospheric-pressure plasma treatment. The surface and pore structures of the polyethylene membrane separator were examined by scanning electron microscopy, revealing a slight alteration in the pore structure. As a result of the incorporation of polar functionalities by atmospheric-pressure plasma activation, the electrolyte uptake and electrochemical impedance of the atmospheric-pressure-plasma-treated membrane separator improved. The investigational results show that the separator surface can be controlled by atmospheric-pressure plasma surface treatment to tailor the hydrophilicity and enhance the electrochemical performance of lithium ion batteries.

  5. Interfacial separation between elastic solids with randomly rough surfaces: comparison of experiment with theory

    Energy Technology Data Exchange (ETDEWEB)

    Lorenz, B; Persson, B N J [IFF, FZ-Juelich, D-52425 Juelich (Germany)

    2009-01-07

    We study the average separation between an elastic solid and a hard solid, with a nominally flat but randomly rough surface, as a function of the squeezing pressure. We present experimental results for a silicon rubber (PDMS) block with a flat surface squeezed against an asphalt road surface. The theory shows that an effective repulsive pressure acts between the surfaces of the form p{approx}exp(-u/u{sub 0}), where u is the average separation between the surfaces and u{sub 0} a constant of the order of the root-mean-square roughness, in good agreement with the experimental results.

  6. Biodegradable polyester films from renewable aleuritic acid: surface modifications induced by melt-polycondensation in air

    International Nuclear Information System (INIS)

    Benítez, José Jesús; De Vargas-Parody, María Inmaculada; Cruz-Carrillo, Miguel Antonio; Heredia-Guerrero, José Alejandro; Morales-Flórez, Victor; De la Rosa-Fox, Nicolás; Heredia, Antonio

    2016-01-01

    Good water barrier properties and biocompatibility of long-chain biopolyesters like cutin and suberin have inspired the design of synthetic mimetic materials. Most of these biopolymers are made from esterified mid-chain functionalized ω-long chain hydroxyacids. Aleuritic (9,10,16-trihydroxypalmitic) acid is such a polyhydroxylated fatty acid and is also the major constituent of natural lac resin, a relatively abundant and renewable resource. Insoluble and thermostable films have been prepared from aleuritic acid by melt-condensation polymerization in air without catalysts, an easy and attractive procedure for large scale production. Intended to be used as a protective coating, the barrier's performance is expected to be conditioned by physical and chemical modifications induced by oxygen on the air-exposed side. Hence, the chemical composition, texture, mechanical behavior, hydrophobicity, chemical resistance and biodegradation of the film surface have been studied by attenuated total reflection–Fourier transform infrared spectroscopy (ATR–FTIR), atomic force microscopy (AFM), nanoindentation and water contact angle (WCA). It has been demonstrated that the occurrence of side oxidation reactions conditions the surface physical and chemical properties of these polyhydroxyester films. Additionally, the addition of palmitic acid to reduce the presence of hydrophilic free hydroxyl groups was found to have a strong influence on these parameters. (paper)

  7. Atmospheric pressure surface sampling/ionization techniques for direct coupling of planar separations with mass spectrometry.

    Science.gov (United States)

    Pasilis, Sofie P; Van Berkel, Gary J

    2010-06-18

    Planar separations, which include thin layer chromatography and gel electrophoresis, are in widespread use as important and powerful tools for conducting separations of complex mixtures. To increase the utility of planar separations, new methods are needed that allow in situ characterization of the individual components of the separated mixtures. A large number of atmospheric pressure surface sampling and ionization techniques for use with mass spectrometry have emerged in the past several years, and several have been investigated as a means for mass spectrometric read-out of planar separations. In this article, we review the atmospheric pressure surface sampling and ionization techniques that have been used for the read-out of planar separation media. For each technique, we briefly explain the operational basics and discuss the analyte type for which it is appropriate and some specific applications from the literature. Copyright (c) 2010 Elsevier B.V. All rights reserved.

  8. Dual-band frequency selective surface with large band separation and stable performance

    International Nuclear Information System (INIS)

    Zhou Hang; Qu Shao-Bo; Lin Bao-Qin; Wang Jia-Fu; Ma Hua; Zhang Jie-Qiu; Peng Wei-Dong; Bai Peng; Wang Xu-Hua; Xu Zhuo

    2012-01-01

    A new technique of designing a dual-band frequency selective surface with large band separation is presented. This technique is based on a delicately designed topology of L- and Ku-band microwave filters. The two band-pass responses are generated by a capacitively-loaded square-loop frequency selective surface and an aperture-coupled frequency selective surface, respectively. A Faraday cage is located between the two frequency selective surface structures to eliminate undesired couplings. Based on this technique, a dual-band frequency selective surface with large band separation is designed, which possesses large band separation, high selectivity, and stable performance under various incident angles and different polarizations. (electromagnetism, optics, acoustics, heat transfer, classical mechanics, and fluid dynamics)

  9. A heat transfer correlation based on a surface renewal model for molten core concrete interaction study

    International Nuclear Information System (INIS)

    Tourniaire, B. . E-mail bruno.tourniaire@cea.fr

    2006-01-01

    The prediction of heat transfer between corium pool and concrete basemat is of particular significance in the framework of the study of PWR's severe accident. Heat transfer directly governs the ablation velocity of concrete in case of molten core concrete interaction (MCCI) and, consequently, the time delay when the reactor cavity may fail. From a restricted hydrodynamic point of view, this issue is related to heat transfer between a heated bubbling pool and a porous wall with gas injection. Several experimental studies have been performed with simulant materials and many correlations have been provided to address this issue. The comparisons of the results of these correlations with the measurements and their extrapolation to reactor materials show that strong discrepancies between the results of these models are obtained which probably means that some phenomena are not well taken into account. The main purpose of this paper is to present an alternative heat transfer model which was originally developed for chemical engineering applications (bubble columns) by Deckwer. A part of this work is devoted to the presentation of this model, which is based on a surface renewal assumption. Comparison of the results of this model with available experimental data in different systems are presented and discussed. These comparisons clearly show that this model can be used to deal with the particular problem of MCCI. The analyses also lead to enrich the original model by taking into account the thermal resistance of the wall: a new formulation of the Deckwer's correlation is finally proposed

  10. The surface renewal method for better spatial resolution of evapotranspiration measurements

    Science.gov (United States)

    Suvocarev, K.; Fischer, M.; Massey, J. H.; Reba, M. L.; Runkle, B.

    2017-12-01

    Evaluating feasible irrigation strategies when water is scarce requires measurements or estimations of evapotranspiration (ET). Direct observations of ET from agricultural fields are preferred, and micrometeorological methods such as eddy covariance (EC) provide a high quality, continuous time series of ET. However, when replicates of the measurements are needed to compare irrigation strategies, the cost of such experiments is often prohibitive and limits experimental scope. An alternative micrometeorological approach to ET, the surface renewal (SR) method, may be reduced to a thermocouple and a propeller anemometer (Castellvi and Snyder, 2009). In this case, net radiation, soil and sensible heat flux (H) are measured and latent heat flux (an energy equivalent for ET) is estimated as the residual of the surface energy-balance equation. In our experiment, thermocouples (Type E Fine-Wire Thermocouple, FW3) were deployed next to the EC system and combined with mean horizontal wind speed measurements to obtain H using SR method for three weeks. After compensating the temperature signal for non-ideal frequency response in the wavelet half-plane and correcting the sonic anemometer for the flow distortion (Horst et al., 2015), the SR H fluxes compared well to those measured by EC (r2 = 0.9, slope = 0.92). This result encouraged us to install thermocouples over 16 rice fields under different irrigation treatments (continuous cascade flood, continuous multiple inlet rice irrigation, alternate wetting and drying, and furrow irrigation). The EC measurements with net radiometer and soil heat flux plates are deployed at three of these fields to provide a direct comparison. The measurement campaign will finish soon and the data will be processed to evaluate the SR approach for ET estimation. The results will be used to show better spatial resolution of ET measurements to support irrigation decisions in agricultural crops.

  11. Flotation separation of polyvinyl chloride and polyethylene terephthalate plastics combined with surface modification for recycling.

    Science.gov (United States)

    Wang, Chongqing; Wang, Hui; Fu, Jiangang; Zhang, Lingling; Luo, Chengcheng; Liu, Younian

    2015-11-01

    Surface modification with potassium permanganate (KMnO4) solution was developed for separation of polyvinyl chloride (PVC) and polyethylene terephthalate (PET) waste plastics. The floatability of PVC decreases with increasing of KMnO4 concentration, treatment time, temperature and stirring rate, while that of PET is unaffected. Fourier transform infrared (FT-IR) analysis confirms that mechanism of surface modification may be due to oxidization reactions occurred on PVC surface. The optimum conditions are KMnO4 concentration 1.25 mM/L, treatment time 50 min, temperature 60°C, stirring rate 300 r/min, frother concentration 17.5 g/L and flotation time 1 min. PVC and PET with different particle sizes were separated efficiently through two-stage flotation. Additionally, after ultrasonic assisted surface modification, separation of PVC and PET with different mass ratios was obtained efficiently through one-stage flotation. The purity and the recovery of the obtained products after flotation separation are up to 99.30% and 99.73%, respectively. A flotation process was designed for flotation separation of PVC and PET plastics combined with surface modification. This study provides technical insights into physical separation of plastic wastes for recycling industry. Copyright © 2015 Elsevier Ltd. All rights reserved.

  12. Green Approach to the Fabrication of Superhydrophobic Mesh Surface for Oil/Water Separation.

    Science.gov (United States)

    Wang, Fajun; Lei, Sheng; Xu, Yao; Ou, Junfei

    2015-07-20

    We report a simple and environment friendly method to fabricate superhydrophobic metallic mesh surfaces for oil/water separation. The obtained mesh surface exhibits superhydrophobicity and superoleophilicity after it was dried in an oven at 200 °C for 10 min. A rough silver layer is formed on the mesh surface after immersion, and the spontaneous adsorption of airborne carbon contaminants on the silver surface lower the surface free energy of the mesh. No low-surface-energy reagents and/or volatile organic solvents are used. In addition, we demonstrate that by using the mesh box, oils can be separated and collected from the surface of water repeatedly, and that high separation efficiencies of larger than 92 % are retained for various oils. Moreover, the superhydrophobic mesh also possesses excellent corrosion resistance and thermal stability. Hence, these superhydrophobic meshes might be good candidates for the practical separation of oil from the surface of water. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  13. Adaptable bioinspired special wetting surface for multifunctional oil/water separation

    Science.gov (United States)

    Kavalenka, Maryna N.; Vüllers, Felix; Kumberg, Jana; Zeiger, Claudia; Trouillet, Vanessa; Stein, Sebastian; Ava, Tanzila T.; Li, Chunyan; Worgull, Matthias; Hölscher, Hendrik

    2017-01-01

    Inspired by the multifunctionality of biological surfaces necessary for the survival of an organism in its specific environment, we developed an artificial special wetting nanofur surface which can be adapted to perform different functionalities necessary to efficiently separate oil and water for cleaning accidental oil spills or separating industrial oily wastewater. Initial superhydrophobic nanofur surface is fabricated using a hot pulling method, in which nano- and microhairs are drawn out of the polymer surface during separation from a heated sandblasted steel plate. By using a set of simple modification techniques, which include microperforation, plasma treatment and subsequent control of storage environment, we achieved selective separation of either water or oil, variable oil absorption and continuous gravity driven separation of oil/water mixtures by filtration. Furthermore, these functions can be performed using special wetting nanofur made from various thermoplastics, including biodegradable and recyclable polymers. Additionally, nanofur can be reused after washing it with organic solvents, thus, further helping to reduce the environmental impacts of oil/water separation processes. PMID:28051163

  14. Distinct Stromal Cell Factor Combinations Can Separately Control Hematopoietic Stem Cell Survival, Proliferation, and Self-Renewal

    Directory of Open Access Journals (Sweden)

    Stefan Wohrer

    2014-06-01

    Full Text Available Hematopoietic stem cells (HSCs are identified by their ability to sustain prolonged blood cell production in vivo, although recent evidence suggests that durable self-renewal (DSR is shared by HSC subtypes with distinct self-perpetuating differentiation programs. Net expansions of DSR-HSCs occur in vivo, but molecularly defined conditions that support similar responses in vitro are lacking. We hypothesized that this might require a combination of factors that differentially promote HSC viability, proliferation, and self-renewal. We now demonstrate that HSC survival and maintenance of DSR potential are variably supported by different Steel factor (SF-containing cocktails with similar HSC-mitogenic activities. In addition, stromal cells produce other factors, including nerve growth factor and collagen 1, that can antagonize the apoptosis of initially quiescent adult HSCs and, in combination with SF and interleukin-11, produce >15-fold net expansions of DSR-HSCs ex vivo within 7 days. These findings point to the molecular basis of HSC control and expansion.

  15. The Role of Controlled Surface Topography and Chemistry on Mouse Embryonic Stem Cell Attachment, Growth and Self-Renewal.

    Science.gov (United States)

    Macgregor, Melanie; Williams, Rachel; Downes, Joni; Bachhuka, Akash; Vasilev, Krasimir

    2017-09-14

    The success of stem cell therapies relies heavily on our ability to control their fate in vitro during expansion to ensure an appropriate supply. The biophysical properties of the cell culture environment have been recognised as a potent stimuli influencing cellular behaviour. In this work we used advanced plasma-based techniques to generate model culture substrates with controlled nanotopographical features of 16 nm, 38 nm and 68 nm in magnitude, and three differently tailored surface chemical functionalities. The effect of these two surface properties on the adhesion, spreading, and self-renewal of mouse embryonic stem cells (mESCs) were assessed. The results demonstrated that physical and chemical cues influenced the behaviour of these stem cells in in vitro culture in different ways. The size of the nanotopographical features impacted on the cell adhesion, spreading and proliferation, while the chemistry influenced the cell self-renewal and differentiation.

  16. CFD simulation of direct contact condensation with ANSYS CFX using surface renewal theory based heat transfer coefficients

    Energy Technology Data Exchange (ETDEWEB)

    Wanninger, Andreas; Ceuca, Sabin Cristian; Macian-Juan, Rafael [Technische Univ. Muenchen, Garching (Germany). Dept. of Nuclear Engineering

    2013-07-01

    Different approaches for the calculation of Direct Contact Condensation (DCC) using Heat Transfer Coefficients (HTC) based on the Surface Renewal Theory (SRT) are tested using the CFD simulation tool ANSYS CFX. The present work constitutes a preliminary study of the flow patterns and conditions observed using different HTC models. A complex 3D flow pattern will be observed in the CFD simulations as well as a strong coupling between the condensation rate and the two-phase flow dynamics. (orig.)

  17. Surface renewal: an advanced micrometeorological method for measuring and processing field-scale energy flux density data.

    Science.gov (United States)

    McElrone, Andrew J; Shapland, Thomas M; Calderon, Arturo; Fitzmaurice, Li; Paw U, Kyaw Tha; Snyder, Richard L

    2013-12-12

    Advanced micrometeorological methods have become increasingly important in soil, crop, and environmental sciences. For many scientists without formal training in atmospheric science, these techniques are relatively inaccessible. Surface renewal and other flux measurement methods require an understanding of boundary layer meteorology and extensive training in instrumentation and multiple data management programs. To improve accessibility of these techniques, we describe the underlying theory of surface renewal measurements, demonstrate how to set up a field station for surface renewal with eddy covariance calibration, and utilize our open-source turnkey data logger program to perform flux data acquisition and processing. The new turnkey program returns to the user a simple data table with the corrected fluxes and quality control parameters, and eliminates the need for researchers to shuttle between multiple processing programs to obtain the final flux data. An example of data generated from these measurements demonstrates how crop water use is measured with this technique. The output information is useful to growers for making irrigation decisions in a variety of agricultural ecosystems. These stations are currently deployed in numerous field experiments by researchers in our group and the California Department of Water Resources in the following crops: rice, wine and raisin grape vineyards, alfalfa, almond, walnut, peach, lemon, avocado, and corn.

  18. Chemical Separation on Silver Nanorods Surface Monitored by TOF-SIMS

    Directory of Open Access Journals (Sweden)

    Ondrej Petruš

    2017-01-01

    Full Text Available The article introduces a possible chemical separation of a mixture of two compounds on the metal nanorods surface. A silver nanorods surface has been prepared by controlled electrochemical deposition in anodic alumina oxide (AAO template. Rhodamine 6G and 4-aminothiophenol have been directly applied to the sampling point on a silver nanorods surface in an aliquot mixture. The position of the resolved compounds was analysed by time-of-flight secondary ion mass spectrometry (TOF-SIMS which measured the fragments and the molecular ions of the two compounds separated on the silver nanorods surface. Rhodamine 6G has been preconcentrated as 1.5 mm radial from the sampling point while 4-aminothiophenol formed a continuous self-assembled monolayer on the silver nanorods surface with a maximum molecular ion intensity at a distance of 0.5 mm from the sampling point. The separation of the single chemical components from the two-component mixture over the examined silver nanostructured films could clearly be shown. A fast separation on the mentioned nanotextured films was observed (within 50 s. This procedure can be easily integrated into the micro/nanofluidic systems or chips and different detection systems can be applied.

  19. Surface patterning of polymeric separation membranes and its influence on the filtration performance

    Science.gov (United States)

    Maruf, Sajjad

    Polymeric membrane based separation technologies are crucial for addressing the global issues such as water purification. However, continuous operations of these processes are often hindered by fouling which increases mass transport resistance of the membrane to permeation and thus the energy cost, and eventually replacement of the membrane in the system. In comparison to other anti-fouling strategies, the use of controlled surface topography to mitigate fouling has not been realized mainly due to the lack of methods to create targeted topography on the porous membrane surface. This thesis aims to develop a new methodology to create surface-patterned polymeric separation membrane to improve their anti-fouling characteristics during filtration. First, successful fabrication of sub-micron surface patterns directly on a commercial ultrafiltration (UF) membrane surface using nanoimprint lithographic (NIL) technique was demonstrated. Comprehensive filtration studies revealed that the presence of these sub-micron surface patterns mitigates not only the onset of colloidal particle deposition, but also lowers the rate of growth of cake layer after initial deposition, in comparison with un-patterned membranes. The anti-fouling effects were also observed for model protein solutions. Staged filtration experiments, with backwash cleaning, revealed that the permeate flux of the patterned membrane after protein fouling was considerably higher than that of the pristine or un-patterned membrane. In addition to the surface-patterning of UF membranes, successful fabrication of a surface-patterned thin film composite (TFC) membrane was shown for the first time. A two-step fabrication process was carried out by (1) nanoimprinting a polyethersulfone (PES) support using NIL, and (2) forming a thin dense film atop the PES support via interfacial polymerization (IP). Fouling experiments suggest that the surface patterns alter the hydrodynamics at the membrane-feed interface, which is

  20. Nanosecond laser ablated copper superhydrophobic surface with tunable ultrahigh adhesion and its renewability with low temperature annealing

    Science.gov (United States)

    He, An; Liu, Wenwen; Xue, Wei; Yang, Huan; Cao, Yu

    2018-03-01

    Recently, metallic superhydrophobic surfaces with ultrahigh adhesion have got plentiful attention on account of their significance in scientific researches and industrial applications like droplet transport, drug delivery and novel microfluidic devices. However, the long lead time and transience hindered its in-depth development and industrial application. In this work, nanosecond laser ablation was carried out to construct grid of micro-grooves on copper surface, whereafter, by applying fast ethanol assisted low-temperature annealing, we obtained surface with superhydrophobicity and ultrahigh adhesion within hours. And the ultrahigh adhesion force was found tunable by varying the groove spacing. Using ultrasonic cleaning as the simulation of natural wear and tear in service, the renewability of superhydrophobicity was also investigated, and the result shows that the contact angle can rehabilitate promptly by the processing of ethanol assisted low-temperature annealing, which gives a promising fast and cheap circuitous strategy to realize the long wish durable metallic superhydrophobic surfaces in practical applications.

  1. Renewable target in sight

    International Nuclear Information System (INIS)

    Anon

    2000-01-01

    Australia's renewable energy industry is expecting several billion dollars of investment over the next 10 years following passage in December last year of the Renewable Energy Electricity) Act 2000 through Federal Parliament. The Act requires an additional 9500GWh of Australia's electricity production to be sourced from renewables by the year 2010. It also establishes a market for the 'green' component of the energy separate from the electricity itself, through a Renewable Energy Certificate (REC), whereby an accredited generator of renewable energy is able to issue one REC for each megawatt-hour of renewable energy generated

  2. Robust superhydrophobic surface by nature-inspired polyphenol chemistry for effective oil-water separation

    Science.gov (United States)

    Bu, Yiming; Huang, Jingjing; Zhang, Shiyu; Wang, Yinghua; Gu, Shaojin; Cao, Genyang; Yang, Hongjun; Ye, Dezhan; Zhou, Yingshan; Xu, Weilin

    2018-05-01

    With the ever-increasing oil spillages, oil-water separation has attracted widespread concern in recent years. In this work, a nature-inspired polyphenol method has been developed to fabricate the durable superhydrophobic surfaces for the oil-water separation. Inspiring from the adhesion of polyphenol and reducing capacity of free catechol/pyrogallol groups in polyphenol, firstly, the simple immersion of commercial materials (melamine sponge, PET, and nonwoven cotton fabrics) in tannic acid (TA) solution allows to form a multifunctional coating on the surface of sponge or fabrics, which was used as reducing reagent to generate Ag nanoparticles (NPs). Then, decoration of 1H, 1H, 2H, 2H-perfluorodecanethiol (PFDT) molecules produced superhydrophobic surfaces. The surface topological structure, chemical composition, and superhydrophobic property of the as-prepared surface are characterized by scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), energy dispersive spectroscopy (EDS), and water contact angle (WCA) measurements. The WCAs of as-prepared sponge and fabrics were higher than 150°. The stability, absorption capacity, and recyclability of as-prepared sponge and fabrics were investigated. The as-prepared sponge demonstrates high oil/water selectivity and high absorption capacity (66-150 g/g) for a broad variety of oils and organic solvents, and was chemically resistant, robust against abrasion, and long-term durability in harsh environments. Most important of all, it can continuously separate various kinds of oils or organic pollutants from the surface of water. This study presents a facile strategy to fabricate superhydrophobic materials for continuous oil-water separation, displaying great potential in large-scale practical application.

  3. Evidence for phase separation of ethanol-water mixtures at the hydrogen terminated nanocrystalline diamond surface.

    Science.gov (United States)

    Janssens, Stoffel D; Drijkoningen, Sien; Saitner, Marc; Boyen, Hans-Gerd; Wagner, Patrick; Larsson, Karin; Haenen, Ken

    2012-07-28

    Interactions between ethanol-water mixtures and a hydrophobic hydrogen terminated nanocrystalline diamond surface, are investigated by sessile drop contact angle measurements. The surface free energy of the hydrophobic surface, obtained with pure liquids, differs strongly from values obtained by ethanol-water mixtures. Here, a model which explains this difference is presented. The model suggests that, due to a higher affinity of ethanol for the hydrophobic surface, when compared to water, a phase separation occurs when a mixture of both liquids is in contact with the H-terminated diamond surface. These results are supported by a computational study giving insight in the affinity and related interaction at the liquid-solid interface.

  4. Tailorable Surface Morphology of 3D Scaffolds by Combining Additive Manufacturing with Thermally Induced Phase Separation.

    Science.gov (United States)

    Di Luca, Andrea; de Wijn, Joost R; van Blitterswijk, Clemens A; Camarero-Espinosa, Sandra; Moroni, Lorenzo

    2017-08-01

    The functionalization of biomaterials substrates used for cell culture is gearing towards an increasing control over cell activity. Although a number of biomaterials have been successfully modified by different strategies to display tailored physical and chemical surface properties, it is still challenging to step from 2D substrates to 3D scaffolds with instructive surface properties for cell culture and tissue regeneration. In this study, additive manufacturing and thermally induced phase separation are combined to create 3D scaffolds with tunable surface morphology from polymer gels. Surface features vary depending on the gel concentration, the exchanging temperature, and the nonsolvent used. When preosteoblasts (MC-3T3 cells) are cultured on these scaffolds, a significant increase in alkaline phosphatase activity is measured for submicron surface topography, suggesting a potential role on early cell differentiation. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  5. Source signature estimation from multimode surface waves via mode-separated virtual real source method

    Science.gov (United States)

    Gao, Lingli; Pan, Yudi

    2018-05-01

    The correct estimation of the seismic source signature is crucial to exploration geophysics. Based on seismic interferometry, the virtual real source (VRS) method provides a model-independent way for source signature estimation. However, when encountering multimode surface waves, which are commonly seen in the shallow seismic survey, strong spurious events appear in seismic interferometric results. These spurious events introduce errors in the virtual-source recordings and reduce the accuracy of the source signature estimated by the VRS method. In order to estimate a correct source signature from multimode surface waves, we propose a mode-separated VRS method. In this method, multimode surface waves are mode separated before seismic interferometry. Virtual-source recordings are then obtained by applying seismic interferometry to each mode individually. Therefore, artefacts caused by cross-mode correlation are excluded in the virtual-source recordings and the estimated source signatures. A synthetic example showed that a correct source signature can be estimated with the proposed method, while strong spurious oscillation occurs in the estimated source signature if we do not apply mode separation first. We also applied the proposed method to a field example, which verified its validity and effectiveness in estimating seismic source signature from shallow seismic shot gathers containing multimode surface waves.

  6. Forced Spreading of Aqueous Solutions on Zwitterionic Sulfobetaine Surfaces for Rapid Evaporation and Solute Separation.

    Science.gov (United States)

    Wu, Cyuan-Jhang; Singh, Vickramjeet; Sheng, Yu-Jane; Tsao, Heng-Kwong

    2017-08-01

    Solute separation of aqueous mixtures is mainly dominated by water vaporization. The evaporation rate of an aqueous drop grows with increasing the liquid-gas interfacial area. The spontaneous spreading behavior of a water droplet on a total wetting surface provides huge liquid-gas interfacial area per unit volume; however, it is halted by the self-pinning phenomenon upon addition of nonvolatile solutes. In this work, it is shown that the solute-induced self-pinning can be overcome by gravity, leading to anisotropic spreading much faster than isotropic spreading. The evaporation rate of anisotropic spreading on a zwitterionic sulfobetaine surface is 25 times larger as that on a poly(methyl methacrylate) surface. Dramatic enhancement of evaporation is demonstrated by simultaneous formation of fog atop liquid film. During anisotropic spreading, the solutes are quickly precipitated out within 30 s, showing the rapid solute-water separation. After repeated spreading process for the dye-containing solution, the mean concentration of the collection is doubled, revealing the concentration efficiency as high as 100%. Gravity-enhanced spreading on total wetting surfaces at room temperature is easy to scale-up with less energy consumption, and thus it has great potentials for the applications of solute separation and concentration.

  7. Bacterial surface layer proteins as a novel capillary coating material for capillary electrophoretic separations

    Energy Technology Data Exchange (ETDEWEB)

    Moreno-Gordaliza, Estefanía, E-mail: emorenog@ucm.es [Division of Analytical Biosciences, Leiden Academic Centre for Drug Research, Universiteit Leiden, Einsteinweg 55, 2300, RA, Leiden (Netherlands); Department of Analytical Chemistry, Faculty of Chemistry, Universidad Complutense de Madrid, Avda. Complutense s/n, 28040, Madrid (Spain); Stigter, Edwin C.A. [Division of Analytical Biosciences, Leiden Academic Centre for Drug Research, Universiteit Leiden, Einsteinweg 55, 2300, RA, Leiden (Netherlands); Department of Molecular Cancer Research, Universitair Medisch Centrum Utrecht, Wilhelmina Kinder Ziekenhuis, Lundlaan 6, 3584, EA Utrecht (Netherlands); Lindenburg, Petrus W.; Hankemeier, Thomas [Division of Analytical Biosciences, Leiden Academic Centre for Drug Research, Universiteit Leiden, Einsteinweg 55, 2300, RA, Leiden (Netherlands)

    2016-06-07

    A novel concept for stable coating in capillary electrophoresis, based on recrystallization of surface layer proteins on hydrophobized fused silica capillaries, was demonstrated. Surface layer protein A (SlpA) from Lactobacillus acidophilus bacteria was extracted, purified and used for coating pre-silanized glass substrates presenting different surface wettabilities (either hydrophobic or hydrophilic). Contact angle determination on SlpA-coated hydrophobic silica slides showed that the surfaces turned to hydrophilic after coating (53 ± 5°), due to a protein monolayer formation by protein-surface hydrophobic interactions. Visualization by atomic force microscopy demonstrated the presence of a SlpA layer on methylated silica slides displaying a surface roughness of 0.44 ± 0.02 nm. Additionally, a protein layer was visualized by fluorescence microscopy in methylated silica capillaries coated with SlpA and fluorescein isothiocyanate-labeled. The SlpA-coating showed an outstanding stability, even after treatment with 20 mM NaOH (pH 12.3). The electroosmotic flow in coated capillaries showed a partial suppression at pH 7.50 (3.8 ± 0.5 10{sup −9} m{sup 2} V{sup −1} s{sup −1}) when compared with unmodified fused silica (5.9 ± 0.1 10{sup −8} m{sup 2} V{sup −1} s{sup −1}). To demonstrate the potential of this novel coating, the SlpA-coated capillaries were applied for the first time for electrophoretic separation, and proved to be very suitable for the isotachophoretic separation of lipoproteins in human serum. The separations showed a high degree of repeatability (absolute migration times with 1.1–1.8% coefficient-of-variation (CV) within a day) and 2–3% CV inter-capillary reproducibility. The capillaries were stable for more than 100 runs at pH 9.40, and showed to be an exceptional alternative for challenging electrophoretic separations at long-term use. - Highlights: • New coating using recrystallized surface-layer proteins on

  8. Actinide-Lanthanide separation by an electrolytic method in molten salt media: feasibility assessment of a renewed liquid cathode

    International Nuclear Information System (INIS)

    Huguet, A.

    2009-12-01

    This study is part of a research program concerning the assessment of pyrochemical methods for the nuclear waste processing. The An-Ln partitioning could be achieved by an electrolytic selective extraction in molten salt media. It has been decided to focus on liquid reactive cathode which better suits to a group actinides co-recycling. The aim of the study is to propose, define and initiate the development of an electrolytic pyro-process dedicated to the quantitative and selective recovery of the actinides. Quantitativeness is related to technology, whereas selectivity is governed by chemistry. The first step consisted in selecting the adequate operating conditions, which enables a sufficient An-Ln separation. The first step consisted, by means of thermodynamic calculi and electrochemical investigations, in selecting a promising combination between molten electrolyte and cathodic material, regarding the process constraints. To improve the recovery yield, it is necessary to develop a disruptive technology: here comes the concept of a dynamic electrodeposition carried out onto liquid metallic drops. The next step consisted in designing and manufacturing a lab-scale device which enables dropping flow studies. Since interfacial phenomena are of primary meaning in such a concept, it has been decided to focus on high temperature liquid-liquid interfacial measurements. (author)

  9. Separation of platelets from whole blood using standing surface acoustic waves in a microchannel.

    Science.gov (United States)

    Nam, Jeonghun; Lim, Hyunjung; Kim, Dookon; Shin, Sehyun

    2011-10-07

    Platelet separation from blood is essential for biochemical analyses and clinical diagnosis. In this article, we propose a method to separate platelets from undiluted whole blood using standing surface acoustic waves (SSAWs) in a microfluidic device. A polydimethylsiloxane (PDMS) microfluidic channel was fabricated and integrated with interdigitated transducer (IDT) electrodes patterned on a piezoelectric substrate. To avoid shear-induced activation of platelets, the blood sample flow was hydrodynamically focused by introducing sheath flow from two side-inlets and pressure nodes were designed to locate at side walls. By means of flow cytometric analysis, the RBC clearance ratio from whole blood was found to be over 99% and the purity of platelets was close to 98%. Conclusively, the present technique using SSAWs can directly separate platelets from undiluted whole blood with higher purity than other methods.

  10. A plateau–valley separation method for textured surfaces with a deterministic pattern

    DEFF Research Database (Denmark)

    Godi, Alessandro; Kühle, Anders; De Chiffre, Leonardo

    2014-01-01

    The effective characterization of textured surfaces presenting a deterministic pattern of lubricant reservoirs is an issue with which many researchers are nowadays struggling. Existing standards are not suitable for the characterization of such surfaces, providing at times values without physical...... meaning. A new method based on the separation between the plateau and valley regions is hereby presented allowing independent functional analyses of the detected features. The determination of a proper threshold between plateaus and valleys is the first step of a procedure resulting in an efficient...

  11. Microphase separation behavior on the surfaces of PEG-MDI-PDMS multiblock copolymer coatings

    International Nuclear Information System (INIS)

    Fang Hongxia; Zhou Shuxue; Wu Limin

    2006-01-01

    A series of poly(ethylene glycol)(PEG)-4,4'-diphenylmethanediisocyanate(MDI)-poly(dimethylsiloxane) (PDMS) multiblock copolymers were synthesized by employing two-step growth polymerization technique. Atomic force microscopy (AFM) observed nanoscopically well-organized phase-separated surfaces consisting of hydrophilic domain from PEG and MDI segments and hydrophobic domain from PDMS segments even with 50 wt.% PDMS in the copolymer, and the multiblock copolymer coatings presented a surface free energy of as low as 6-8 mN m -1

  12. Energy-separated sequential irradiation for ripple pattern tailoring on silicon surfaces

    Energy Technology Data Exchange (ETDEWEB)

    Kumar, Tanuj [Department of Physics, Central University of Haryana, Jant-Pali, Mahendergarh 1123029 (India); Inter University Accelerator Centre, Aruna Asaf Ali Marg, New Delhi 110067 (India); Kumar, Manish, E-mail: manishbharadwaj@gmail.com [Department of Physics, Central University of Rajasthan, Kishangarh 305801 (India); Panchal, Vandana [Department of Physics, National Institute of Technology, Kurukshetra 136119 (India); Sahoo, P.K. [School of Physical Sciences, National Institute of Science Education and Research, Bhubaneswar 751005 (India); Kanjilal, D. [Inter University Accelerator Centre, Aruna Asaf Ali Marg, New Delhi 110067 (India)

    2015-12-01

    Highlights: • A new process for controlling the near-surface amorphization of ripples on Si surfaces. • Ripples generation by 100 KeV Ar{sup +} and amorphization control by 60 KeV Ar{sup +} irradiation. • Advantage of energy-separated irradiation demonstrated by detailed RBS and AFM studies. • Relevant mechanism is presented on the basis of DAMAGE and SIMNRA simulations. • Key role of solid flow towards the amorphous/crystalline interface is demonstrated. - Abstract: Nanoscale ripples on semiconductor surfaces have potential application in biosensing and optoelectronics, but suffer from uncontrolled surface-amorphization when prepared by conventional ion-irradiation methods. A two-step, energy-separated sequential-irradiation enables simultaneous control of surface-amorphization and ripple-dimensions on Si(1 0 0). The evolution of ripples using 100 keV Ar{sup +} bombardment and further tuning of the patterns using a sequential-irradiation by 60 keV Ar{sup +} at different fluences are demonstrated. The advantage of this approach as opposed to increased fluence at the same energy is clarified by atomic force microscopy and Rutherford backscattering spectroscopy investigations. The explanation of our findings is presented through DAMAGE simulation.

  13. SEPARATION OF CELL POPULATIONS BY SUPER-PARAMAGNETIC PARTICLES WITH CONTROLLED SURFACE FUNCTIONALITY

    Directory of Open Access Journals (Sweden)

    Lootsik M. D.

    2014-02-01

    Full Text Available The recognition and isolation of specific mammalian cells by the biocompatible polymer coated super-paramagnetic particles with determined surface functionality were studied. The method of synthesis of nanoscaled particles on a core of iron III oxide (Fe2O3, magemit coated with a polymer shell containing reactive oligoperoxide groups for attachment of ligands is described. By using the developed superparamagnetic particles functionalized with peanut agglutinin (PNA we have separated the sub-populations of PNA+ and PNA– cells from ascites of murine Nemeth-Kellner lymphoma. In another type of experiment, the particles were opsonized with proteins of the fetal calf serum that improved biocompatibility of the particles and their ingestion by cultivated murine macrophages J774.2. Macrophages loaded with the particles were effeciently separated from the particles free cells by using the magnet. Thus, the developed surface functionalized superparamagnetic particles showed to be a versatile tool for cell separation independent on the mode of particles’ binding with cell surface or their engulfment by the targeted cells.

  14. Lateral phase separation of mixed polymer brushes on planar and spherical surfaces

    Science.gov (United States)

    van Lehn, Reid; Alexander-Katz, Alfredo

    2012-02-01

    A mixed polymer brush consists of two (or more) polymer species grafted to a surface at a high density, inducing the polymers to highly stretch to maximize favorable solvent interactions while minimizing polymer overlap. The enthalpic and entropic interactions between the different polymers give rise to lateral phase behavior on the surface. Understanding this phase separation behavior is interesting for applications in nanotemplating and controlled protein adsorption. In this work, we present a novel theoretical model to quickly predict lateral phase separated morphologies of mixed polymer brushes on planar, cylindrical and spherical surfaces. The model combines a Flory-Huggins model for enthalpic interactions between the polymer components with an Alexander-de Gennes model for the entropy of the brush layers. When there is a length difference between the polymer components, these two interactions along with the conformational entropy of the system lead to a range of morphologies including stripes, dimples, mixing, and complete phase separation. The computational efficiency of this model allows for phase diagrams to be generated with great accuracy. The results of our model thus allow for the fast prediction of lateral morphologies on different geometries.

  15. Mechanically durable underwater superoleophobic surfaces based on hydrophilic bulk metals for oil/water separation

    Science.gov (United States)

    Yu, Huadong; Lian, Zhongxu; Xu, Jinkai; Wan, Yanling; Wang, Zuobin; Li, Yiquan; Yu, Zhanjiang; Weng, Zhankun

    2018-04-01

    Despite the success of previous methods for fabricating underwater superoleophobic surfaces, most of the surfaces based on soft materials are prone to collapse and deformation due to their mechanically fragile nature, and they fail to perform their designed functions after the surface materials are damaged in water. In this work, the nanosecond laser-induced oxide coatings on hydrophilic bulk metals are reported which overcomes the limitation and shows the robust underwater superoleophobicity to a mechanical challenge encountered by surfaces deployed in water environment. The results show that the surface materials have the advantage that the underwater superoleophobicity is still preserved after the surfaces are scratched by knife or sandpaper and even completely destroyed because of the hydrophilic property of damaged materials in water. It is important that the results provide a guide for the design of durable underwater superoleophobic surfaces, and the development of superoleophobic materials in many potential applications such as the oil-repellent and the oil/water separation. Additionally, the nanosecond laser technology is simple, cost-effective and suitable for the large-area and mass fabrication of mechanically durable underwater superoleophobic metal materials.

  16. Optically transparent, mechanically durable, nanostructured superhydrophobic surfaces enabled by spinodally phase-separated glass thin films.

    Science.gov (United States)

    Aytug, Tolga; Simpson, John T; Lupini, Andrew R; Trejo, Rosa M; Jellison, Gerald E; Ivanov, Ilia N; Pennycook, Stephen J; Hillesheim, Daniel A; Winter, Kyle O; Christen, David K; Hunter, Scott R; Haynes, J Allen

    2013-08-09

    We describe the formation and properties of atomically bonded, optical quality, nanostructured thin glass film coatings on glass plates, utilizing phase separation by spinodal decomposition in a sodium borosilicate glass system. Following deposition via magnetron sputtering, thermal processing and differential etching, these coatings are structurally superhydrophilic (i.e., display anti-fogging functionality) and demonstrate robust mechanical properties and superior abrasion resistance. After appropriate chemical surface modification, the surfaces display a stable, non-wetting Cassie-Baxter state and exhibit exceptional superhydrophobic performance, with water droplet contact angles as large as 172°. As an added benefit, in both superhydrophobic and superhydrophilic states these nanostructured surfaces can block ultraviolet radiation and can be engineered to be anti-reflective with broadband and omnidirectional transparency. Thus, the present approach could be tailored toward distinct coatings for numerous markets, such as residential windows, windshields, specialty optics, goggles, electronic and photovoltaic cover glasses, and optical components used throughout the US military.

  17. Optically transparent, mechanically durable, nanostructured superhydrophobic surfaces enabled by spinodally phase-separated glass thin films

    Science.gov (United States)

    Aytug, Tolga; Simpson, John T.; Lupini, Andrew R.; Trejo, Rosa M.; Jellison, Gerald E.; Ivanov, Ilia N.; Pennycook, Stephen J.; Hillesheim, Daniel A.; Winter, Kyle O.; Christen, David K.; Hunter, Scott R.; Haynes, J. Allen

    2013-08-01

    We describe the formation and properties of atomically bonded, optical quality, nanostructured thin glass film coatings on glass plates, utilizing phase separation by spinodal decomposition in a sodium borosilicate glass system. Following deposition via magnetron sputtering, thermal processing and differential etching, these coatings are structurally superhydrophilic (i.e., display anti-fogging functionality) and demonstrate robust mechanical properties and superior abrasion resistance. After appropriate chemical surface modification, the surfaces display a stable, non-wetting Cassie-Baxter state and exhibit exceptional superhydrophobic performance, with water droplet contact angles as large as 172°. As an added benefit, in both superhydrophobic and superhydrophilic states these nanostructured surfaces can block ultraviolet radiation and can be engineered to be anti-reflective with broadband and omnidirectional transparency. Thus, the present approach could be tailored toward distinct coatings for numerous markets, such as residential windows, windshields, specialty optics, goggles, electronic and photovoltaic cover glasses, and optical components used throughout the US military.

  18. Optically transparent, mechanically durable, nanostructured superhydrophobic surfaces enabled by spinodally phase-separated glass thin films

    International Nuclear Information System (INIS)

    Aytug, Tolga; Simpson, John T; Lupini, Andrew R; Trejo, Rosa M; Jellison, Gerald E; Ivanov, Ilia N; Pennycook, Stephen J; Hillesheim, Daniel A; Winter, Kyle O; Christen, David K; Hunter, Scott R; Allen Haynes, J

    2013-01-01

    We describe the formation and properties of atomically bonded, optical quality, nanostructured thin glass film coatings on glass plates, utilizing phase separation by spinodal decomposition in a sodium borosilicate glass system. Following deposition via magnetron sputtering, thermal processing and differential etching, these coatings are structurally superhydrophilic (i.e., display anti-fogging functionality) and demonstrate robust mechanical properties and superior abrasion resistance. After appropriate chemical surface modification, the surfaces display a stable, non-wetting Cassie–Baxter state and exhibit exceptional superhydrophobic performance, with water droplet contact angles as large as 172°. As an added benefit, in both superhydrophobic and superhydrophilic states these nanostructured surfaces can block ultraviolet radiation and can be engineered to be anti-reflective with broadband and omnidirectional transparency. Thus, the present approach could be tailored toward distinct coatings for numerous markets, such as residential windows, windshields, specialty optics, goggles, electronic and photovoltaic cover glasses, and optical components used throughout the US military. (paper)

  19. Anisotropic surface physicochemical properties of spodumene and albite crystals: Implications for flotation separation

    Science.gov (United States)

    Xu, Longhua; Peng, Tiefeng; Tian, Jia; Lu, Zhongyuan; Hu, Yuehua; Sun, Wei

    2017-12-01

    Aluminosilicate minerals (e.g., spodumene, albite) have complex crystal structures and similar surface chemistries, but they have poor selectivity compared to traditional fatty acid collectors, making flotation separation difficult. Previous research has mainly considered the mineral crystal structure as a whole. In contrast, the surface characteristics at the atomic level and the effects of different crystal interfaces on the flotation behavior have rarely been investigated. This study focuses on investigating the surface anisotropy quantitatively, including the chemical bond characteristics, surface energies, and broken bond densities, using density functional theory and classical theoretical calculations. In addition, the anisotropy of the surface wettability and adsorption characteristics were examined using contact angle, zeta potential, and Fourier-transform infrared measurements. Finally, these surface anisotropies with different flotation behaviors were investigated and interpreted using molecular dynamics simulations, scanning electron microscopy, and X-ray photoelectron spectroscopy. This systematic research offers new ideas concerning the selective grinding and stage flotation of aluminosilicate minerals based on the crystal characteristics.

  20. Smart surfaces with switchable superoleophilicity and superoleophobicity in aqueous media: Toward controllable oil/water separation

    KAUST Repository

    Zhang, L.

    2012-02-01

    Advanced materials with surfaces that have controllable oil wettability when submerged in aqueous media have great potential for various underwater applications. Here we have developed smart surfaces on commonly used materials, including non-woven textiles and polyurethane sponges, which are able to switch between superoleophilicity and superoleophobicity in aqueous media. The smart surfaces are obtained by grafting a block copolymer, comprising blocks of pH-responsive poly(2-vinylpyridine) and oleophilic/hydrophobic polydimethylsiloxane (i.e., P2VP-b-PDMS) on these materials. The P2VP block can alter its wettability and its conformation via protonation and deprotonation in response to the pH of the aqueous media, which provides controllable and switchable access of oil by the PDMS block, resulting in the switchable surface oil wettability in the aqueous media. On the other hand, the high flexibility of the PDMS block facilitates the reversible switching of the surface oil wettability. As a proof of concept, we also demonstrate that materials functionalized with our smart surfaces can be used for highly controllable oil/water separation processes.

  1. Separation of top and bottom surface conduction in Bi2Te3 thin films

    International Nuclear Information System (INIS)

    Yu Xinxin; He Liang; Lang Murong; Jiang Wanjun; Kou Xufeng; Tang Jianshi; Huang Guan; Wang, Kang L; Xiu Faxian; Liao Zhiming; Zou Jin; Wang Yong; Zhang Peng

    2013-01-01

    Quantum spin Hall (QSH) systems are insulating in the bulk with gapless edges or surfaces that are topologically protected and immune to nonmagnetic impurities or geometric perturbations. Although the QSH effect has been realized in the HgTe/CdTe system, it has not been accomplished in normal 3D topological insulators. In this work, we demonstrate a separation of two surface conductions (top/bottom) in epitaxially grown Bi 2 Te 3 thin films through gate dependent Shubnikov–de Haas (SdH) oscillations. By sweeping the gate voltage, only the Fermi level of the top surface is tuned while that of the bottom surface remains unchanged due to strong electric field screening effects arising from the high dielectric constant of Bi 2 Te 3 . In addition, the bulk conduction can be modulated from n- to p-type with a varying gate bias. Our results on the surface control hence pave a way for the realization of QSH effect in topological insulators which requires a selective control of spin transports on the top/bottom surfaces. (paper)

  2. Bioinspired polydopamine particles-assisted construction of superhydrophobic surfaces for oil/water separation.

    Science.gov (United States)

    Shang, Bin; Wang, Yanbing; Peng, Bo; Deng, Ziwei

    2016-11-15

    Frequent oil spillages and industrial discharge of oils/organic solvents have induced severe environmental pollution and ecological damage, and a great cost in energy and finance has been consumed to solve the problems raised. Therefore, it is urgent to develop a surface hydrophobic modification that can be applied to materials with desired properties of high separation efficiency, excellent selectivity and stable performance in extreme conditions during the oil/water separation. Herein, with combined bioinspirations from mussel adhesive protein (polydopamine) and superhydrophobic lotus leaf (hierarchical structures), we develop a general way to superhydrophobically modify various commercial materials, aiming for the selective removal of oils/organic solvents from water. In this procedure, immersing commercial materials (e.g. melamine sponge, stainless steel mesh, nylon netting and cotton cloth) into water/ethanol/ammonia mixtures at a low concentration of dopamine (DA, 2mg/mL) allows a polydopamine (PDA) coating with a tunable roughness appearing on the substrate in one step. This is because DA can self-polymerize and form PDA particles with a catalyst of ammonia, attaching to any surfaces due to abundant catechol and amine groups in PDA, and ultimately, resulting in hierarchical structures. The subsequent decoration with 1H, 1H, 2H, 2H-perfluorodecanethiol features the surface superhydrophobic and superoleophilic. This approach is straightforward and economic, and carried out under a mild, environmental-benign circumstance, with nonspecific substrate demands. In addition, the as-prepared superhydrophobic materials exhibit excellent separation performances including high absorption/separation capacity, excellent selectivity, and extraordinary recyclability for collecting various oils/organic solvents from water. These superhydrophobic materials have also verified to be highly chemical resistant, environment stable and mechanically durable. Therefore, this

  3. APPLICATION OF A SURFACE-RENEWAL MODEL TO PERMEATE-FLUX DATA FOR CONSTANTPRESSURE CROSS-FLOW MICROFILTRATION WITH DEAN VORTICES

    Directory of Open Access Journals (Sweden)

    G. Idan

    2015-06-01

    Full Text Available AbstractThe introduction of flow instabilities into a microfiltration process can dramatically change several elements such as the surface-renewal rate, permeate flux, specific cake resistance, and cake buildup on the membrane in a positive way. A recently developed surface-renewal model for constant-pressure, cross-flow microfiltration (Hasan et al., 2013 is applied to the permeate-flux data reported by Mallubhotla and Belfort (1997, one set of which included flow instabilities (Dean vortices while the other set did not. The surface-renewal model has two forms - the complete model and an approximate model. For the complete model, the introduction of vortices leads to a 53% increase in the surface-renewal rate, which increases the limiting (i.e., steady-state permeate flux by 30%, decreases the specific cake resistance by 14.5% and decreases the limiting cake mass by 15.5% compared to operation without vortices. For the approximate model, a 50% increase in the value of surface renewal rate is shown due to vortices, which increases the limiting permeate flux by 30%, decreases the specific cake resistance by 10.5% and decreases the limiting cake mass by 13.7%. The cake-filtration version of the critical-flux model of microfiltration (Field et al., 1995 is also compared against the experimental permeate-flux data of Mallubhotla and Belfort (1997. Although this model can represent the data, the quality of its fit is inferior compared to that of the surface-renewal model.

  4. Surveillance of parasitic Legionella in surface waters by using immunomagnetic separation and amoebae enrichment.

    Science.gov (United States)

    Hsu, Tsui-Kang; Wu, Shu-Fen; Hsu, Bing-Mu; Kao, Po-Min; Tao, Chi-Wei; Shen, Shu-Min; Ji, Wen-Tsai; Huang, Wen-Chien; Fan, Cheng-Wei

    2015-01-01

    Free-living amoebae (FLA) are potential reservoirs of Legionella in aquatic environments. However, the parasitic relationship between various Legionella and amoebae remains unclear. In this study, surface water samples were gathered from two rivers for evaluating parasitic Legionella. Warmer water temperature is critical to the existence of Legionella. This result suggests that amoebae may be helpful in maintaining Legionella in natural environments because warmer temperatures could enhance parasitisation of Legionella in amoebae. We next used immunomagnetic separation (IMS) to identify extracellular Legionella and remove most free Legionella before detecting the parasitic ones in selectively enriched amoebae. Legionella pneumophila was detected in all the approaches, confirming that the pathogen is a facultative amoebae parasite. By contrast, two obligate amoebae parasites, Legionella-like amoebal pathogens (LLAPs) 8 and 9, were detected only in enriched amoebae. However, several uncultured Legionella were detected only in the extracellular samples. Because the presence of potential hosts, namely Vermamoeba vermiformis, Acanthamoeba spp. and Naegleria gruberi, was confirmed in the samples that contained intracellular Legionella, uncultured Legionella may survive independently of amoebae. Immunomagnetic separation and amoebae enrichment may have referential value for detecting parasitic Legionella in surface waters.

  5. Materials surface treatments by concentrated solar light: a renewable energy option

    International Nuclear Information System (INIS)

    Martinez, D.; Rodriguez, J.

    1998-01-01

    The possible applications of solar furnaces to materials surface treatment are explained in an illustrative manner. A brief description of these systems is exposed, as well as an overview of the feasible industrial or testing applications for which their validity has been proven. (Author) 5 refs

  6. Recent developments in automatic solid-phase extraction with renewable surfaces exploiting flow-based approaches

    DEFF Research Database (Denmark)

    Miró, Manuel; Hartwell, Supaporn Kradtap; Jakmunee, Jaroon

    2008-01-01

    ,on-line SPE assays performed in permanent mode lack sufficient reliability as a consequence of progressively tighter packing of the bead reactor, contamination of the solid surfaces and potential leakage of functional moieties. This article overviews the current state-of-the-art of an appealing tool...... chemical-derivatization reactions, and it pinpoints the most common instrumental detection techniques utilized. We present and discuss in detail relevant environmental and bioanalytical applications reported in the past few years....

  7. INFLUENCE OF RESIDENCE-TIME DISTRIBUTION ON A SURFACE-RENEWAL MODEL OF CONSTANT-PRESSURE CROSS-FLOW MICROFILTRATION

    Directory of Open Access Journals (Sweden)

    W. Zhang

    2015-03-01

    Full Text Available Abstract This work examines the influence of the residence-time distribution (RTD of surface elements on a model of cross-flow microfiltration that has been proposed recently (Hasan et al., 2013. Along with the RTD from the previous work (Case 1, two other RTD functions (Cases 2 and 3 are used to develop theoretical expressions for the permeate-flux decline and cake buildup in the filter as a function of process time. The three different RTDs correspond to three different startup conditions of the filtration process. The analytical expressions for the permeate flux, each of which contains three basic parameters (membrane resistance, specific cake resistance and rate of surface renewal, are fitted to experimental permeate flow rate data in the microfiltration of fermentation broths in laboratory- and pilot-scale units. All three expressions for the permeate flux fit the experimental data fairly well with average root-mean-square errors of 4.6% for Cases 1 and 2, and 4.2% for Case 3, respectively, which points towards the constructive nature of the model - a common feature of theoretical models used in science and engineering.

  8. Influence of nanoparticle–graphene separation on the localized surface plasmon resonances of metal nanoparticles

    Energy Technology Data Exchange (ETDEWEB)

    Masoudian Saadabad, Reza, E-mail: masoudian-reza@yahoo.com, E-mail: rms@mail.usb.ac.ir; Aporvari, Ahmad Shafiei [University of Sistan and Baluchestan, Department of Physics (Iran, Islamic Republic of); Shirdel-Havar, Amir Hushang [Golestan University, Department of Physics (Iran, Islamic Republic of); Havar, Majid Shirdel [University of Kashan, Department of Physics (Iran, Islamic Republic of)

    2016-01-15

    We develop a theory to model the interaction of graphene substrate with localized plasmon resonances in metallic nanoparticles. The influence of a graphene substrate on the surface plasmon resonances is described using an effective background permittivity that is derived from a pseudoparticle concept using the electrostatic method. For this purpose, the interaction of metal nanoparticle with graphene sheet is studied to obtain the optical spectrum of gold nanoparticles deposited on a graphene substrate. Then, we introduce a factor based on dipole approximation to predict the influence of the separation of nanoparticles and graphene on the spectral position of the localized plasmon resonance of the nanoparticles. We applied the theory for a 4-nm-radius gold nanosphere placed near 1.5 nm graphene layer. It is shown that a blue shift is emerged in the position of plasmon resonance when the nanoparticle moves away from graphene.

  9. Shock tunnel measurements of surface pressures in shock induced separated flow field using MEMS sensor array

    International Nuclear Information System (INIS)

    Sriram, R; Jagadeesh, G; Ram, S N; Hegde, G M; Nayak, M M

    2015-01-01

    Characterized not just by high Mach numbers, but also high flow total enthalpies—often accompanied by dissociation and ionization of flowing gas itself—the experimental simulation of hypersonic flows requires impulse facilities like shock tunnels. However, shock tunnel simulation imposes challenges and restrictions on the flow diagnostics, not just because of the possible extreme flow conditions, but also the short run times—typically around 1 ms. The development, calibration and application of fast response MEMS sensors for surface pressure measurements in IISc hypersonic shock tunnel HST-2, with a typical test time of 600 μs, for the complex flow field of strong (impinging) shock boundary layer interaction with separation close to the leading edge, is delineated in this paper. For Mach numbers 5.96 (total enthalpy 1.3 MJ kg −1 ) and 8.67 (total enthalpy 1.6 MJ kg −1 ), surface pressures ranging from around 200 Pa to 50 000 Pa, in various regions of the flow field, are measured using the MEMS sensors. The measurements are found to compare well with the measurements using commercial sensors. It was possible to resolve important regions of the flow field involving significant spatial gradients of pressure, with a resolution of 5 data points within 12 mm in each MEMS array, which cannot be achieved with the other commercial sensors. In particular, MEMS sensors enabled the measurement of separation pressure (at Mach 8.67) near the leading edge and the sharply varying pressure in the reattachment zone. (paper)

  10. Highly efficient separation of surfactant stabilized water-in-oil emulsion based on surface energy gradient and flame retardancy.

    Science.gov (United States)

    Long, Mengying; Peng, Shan; Deng, Wanshun; Miao, Xinrui; Wen, Ni; Zhou, Qiannan; Deng, Wenli

    2018-06-15

    Surface energy gradient would generate an imbalance force to drive tiny water droplets in dry air from the hydrophilic bumps to superhydrophobic domains, which has found on the Stenocara beetle's back. Inspired by this phenomenon, we introduced a pristine superhydrophilic filter paper on the lower surface energy superhydrophobic filter paper. ZnSn(OH) 6 particles and polydimethylsiloxane were mixed to prepare the superhydrophobic coating, and the coating was spray-coated on the poly(dialkyldimethylammonium chloride) covered filter paper to separate the span 80 stabilized water-in-isooctane emulsion. A pristine filter paper was added on the superhydrophobic filter paper to fabricate another membrane for separation. The results revealed that with a pristine filter paper, the membrane performed higher efficiency and more recyclability, and it could separate the emulsions with higher surfactant concentrations. The stabilized water droplets passed the superamphiphilic surface, and hindered by the superhydrophobic surface, generating a surface energy gradient for better separation. In addition, the superhydrophobic membrane could be protected from fire to some degree due to the introduced ZnSn(OH) 6 particles with excellent flame retardancy. This easy and efficient approach via simply bringing in pristine superhydrophilic membrane has great potential applications for water-in-oil emulsion separation or oil purification. Copyright © 2018 Elsevier Inc. All rights reserved.

  11. Extraction, stability, and separation of betalains from Opuntia joconostle cv. using response surface methodology.

    Science.gov (United States)

    Sanchez-Gonzalez, Noe; Jaime-Fonseca, Monica R; San Martin-Martinez, Eduardo; Zepeda, L Gerardo

    2013-12-11

    Betalains were extracted and analyzed from Opuntia joconostle (the prickly pear known as xoconostle in Mexico). For the extraction, two solvent systems were used, methanol/water and ethanol/water. A three-variable Box-Behnken statistical design was used for extraction: solvent concentration (0-80%, v/v), temperature (5-30 °C), and treatment time (10-30 min). The extraction and stability of betalains from xoconostle were studied using response surface methodology (RSM). Techniques such as UV-vis, column chromatography, and HPLC were employed for the separation and analysis of the main pigments present in the extracts. Maximum pigment concentration (92 mg/100 g of fruit) was obtained at a temperature of 15 °C and a time of 10 min for methanol/water (20:80), whereas maximum stability of the pigment was observed at pH 5 and a temperature of 25 °C. HPLC chromatograms showed the main betalains of the xoconostle characterized were betalain, betanidin, and isobetalain.

  12. Nanoporous, Metal Carbide, Surface Diffusion Membranes for High Temperature Hydrogen Separations

    Energy Technology Data Exchange (ETDEWEB)

    Way, J. Douglas [Colorado School of Mines, Golden, CO (United States). Dept. of Chemical and Biological Engineering; Wolden, Colin A. [Colorado School of Mines, Golden, CO (United States)

    2013-09-30

    Colorado School of Mines (CSM) developed high temperature, hydrogen permeable membranes that contain no platinum group metals with the goal of separating hydrogen from gas mixtures representative of gasification of carbon feedstocks such as coal or biomass in order to meet DOE NETL 2015 hydrogen membrane performance targets. We employed a dual synthesis strategy centered on transition metal carbides. In the first approach, novel, high temperature, surface diffusion membranes based on nanoporous Mo2C were fabricated on ceramic supports. These were produced in a two step process that consisted of molybdenum oxide deposition followed by thermal carburization. Our best Mo2C surface diffusion membrane achieved a pure hydrogen flux of 367 SCFH/ft2 at a feed pressure of only 20 psig. The highest H2/N2 selectivity obtained with this approach was 4.9. A transport model using “dusty gas” theory was derived to describe the hydrogen transport in the Mo2C coated, surface diffusion membranes. The second class of membranes developed were dense metal foils of BCC metals such as vanadium coated with thin (< 60 nm) Mo2C catalyst layers. We have fabricated a Mo2C/V composite membrane that in pure gas testing delivered a H2 flux of 238 SCFH/ft2 at 600 °C and 100 psig, with no detectable He permeance. This exceeds the 2010 DOE Target flux. This flux is 2.8 times that of pure Pd at the same membrane thickness and test conditions and over 79% of the 2015 flux target. In mixed gas testing we achieved a permeate purity of ≥99.99%, satisfying the permeate purity milestone, but the hydrogen permeance was low, ~0.2 SCFH/ft2.psi. However, during testing of a Mo2C coated Pd alloy membrane with DOE 1 feed gas mixture a hydrogen permeance of >2 SCFH/ft2.psi was obtained which was stable during the entire test, meeting the permeance associated with

  13. Radiative heat transfer exceeding the blackbody limit between macroscale planar surfaces separated by a nanosize vacuum gap

    Science.gov (United States)

    Bernardi, Michael P.; Milovich, Daniel; Francoeur, Mathieu

    2016-09-01

    Using Rytov's fluctuational electrodynamics framework, Polder and Van Hove predicted that radiative heat transfer between planar surfaces separated by a vacuum gap smaller than the thermal wavelength exceeds the blackbody limit due to tunnelling of evanescent modes. This finding has led to the conceptualization of systems capitalizing on evanescent modes such as thermophotovoltaic converters and thermal rectifiers. Their development is, however, limited by the lack of devices enabling radiative transfer between macroscale planar surfaces separated by a nanosize vacuum gap. Here we measure radiative heat transfer for large temperature differences (~120 K) using a custom-fabricated device in which the gap separating two 5 × 5 mm2 intrinsic silicon planar surfaces is modulated from 3,500 to 150 nm. A substantial enhancement over the blackbody limit by a factor of 8.4 is reported for a 150-nm-thick gap. Our device paves the way for the establishment of novel evanescent wave-based systems.

  14. Surface-ionization ion source designed for in-beam operation with the BEMS-2 isotope separator

    International Nuclear Information System (INIS)

    Bogdanov, D.D.; Voboril, J.; Demyanov, A.V.; Karnaukhov, V.A.; Petrov, L.A.

    1976-01-01

    A surface-ionization ion source designed to operate in combination with the BEMS-2 isotope separator in a heavy ion beam is described. The ion source is adjusted for the separation of rare-earth elements. The separation efficiency for 150 Dy is determined to be equal to about 20% at the ionizer temperature of 2600 deg K. The hold-up times for praseodymium, promethium and dysprosium in the ion source range from 5 to 10 sec at the ionizer temperature of 2500-2700 deg K

  15. Superfocusing modes of surface plasmon polaritons in conical geometry based on the quasi-separation of variables approach

    International Nuclear Information System (INIS)

    Kurihara, Kazuyoshi; Otomo, Akira; Syouji, Atsushi; Takahara, Junichi; Suzuki, Koji; Yokoyama, Shiyoshi

    2007-01-01

    Analytic solutions to the superfocusing modes of surface plasmon polaritons in a conical geometry are theoretically studied using an ingenious method called the quasi-separation of variables. This method can be used to look for fundamental solutions to the wave equation for a field that must satisfy boundary conditions at all points on the continuous surface of tapered geometries. The set of differential equations exclusively separated from the wave equation can be consistently solved in combination with perturbation methods. This paper presents the zeroth-order perturbation solution of conical superfocusing modes with azimuthal symmetry and graphically represents them in electric field-line patterns

  16. Study on Water Quality of Surface Runoff and Groundwater Runoff on the Basis of Separation by a Numerical Filter

    OpenAIRE

    Kawara, Osami; Fukumoto, Kohji

    1994-01-01

    In this study we investigated the water quality of surface runoff and groundwater runoff from the basins of the Yodo River and the Asahi River based on that separated by a numerical filter. The water quality of the surface runoff is greatly different from the groundwater runoff. The tendency of concentration change in accordance with river discharges is different from each other. The water qtiality of groundwater runoff changes with river discharges clockwise in many cases. The differences of...

  17. Surface-Enhanced Separation of Water from Hydrocarbons: Potential Dewatering Membranes for the Catalytic Fast Pyrolysis of Pine Biomass

    Energy Technology Data Exchange (ETDEWEB)

    Engtrakul, Chaiwat; Hu, Michael Z.; Bischoff, Brian L.; Jang, Gyoung G.

    2016-10-20

    The impact of surface-selective coatings on water permeation through a membrane when exposed to catalytic fast pyrolysis (CFP) vapor products was studied by tailoring the surface properties of the membrane coating from superhydrophilic to superhydrophobic. Our approach used high-performance architectured surface-selective (HiPAS) membranes that were inserted after a CFP reactor. At this insertion point, the inner wall surface of a tubular membrane was exposed to a mixture of water and upgraded product vapors, including light gases and deoxygenated hydrocarbons. Under proper membrane operating conditions, a high selectivity for water over one-ring upgraded biomass pyrolysis hydrocarbons was observed as a result of a surface-enhanced capillary condensation process. Owing to this surface-enhanced effect, HiPAS membranes have the potential to enable high flux separations, suggesting that water can be selectively removed from the CFP product vapors.

  18. Renewal processes

    CERN Document Server

    Mitov, Kosto V

    2014-01-01

    This monograph serves as an introductory text to classical renewal theory and some of its applications for graduate students and researchers in mathematics and probability theory. Renewal processes play an important part in modeling many phenomena in insurance, finance, queuing systems, inventory control and other areas. In this book, an overview of univariate renewal theory is given and renewal processes in the non-lattice and lattice case are discussed. A pre-requisite is a basic knowledge of probability theory.

  19. Surface-Modified Membrane as A Separator for Lithium-Ion Polymer Battery

    Directory of Open Access Journals (Sweden)

    Jun Young Kim

    2010-04-01

    Full Text Available This paper describes the fabrication of novel modified polyethylene (PE membranes using plasma technology to create high-performance and cost-effective separator membranes for practical applications in lithium-ion polymer batteries. The modified PE membrane via plasma modification process plays a critical role in improving wettability and electrolyte retention, interfacial adhesion between separators and electrodes, and cycle performance of lithium-ion polymer batteries. This paper suggests that the performance of lithium-ion polymer batteries can be greatly enhanced by the plasma modification of commercial separators with proper functional materials for targeted application.

  20. Renewable energy

    DEFF Research Database (Denmark)

    Olsen, Birgitte Egelund

    2016-01-01

    Renewable energy projects are increasingly confronted by local opposition, which delays and sometimes even prevents their implementation. This reflects the frequent gap between support for the general idea of renewables as a strategy for reducing carbon emissions, and acceptance of renewable energy...

  1. Polydimethylsiloxane-Based Superhydrophobic Surfaces on Steel Substrate: Fabrication, Reversibly Extreme Wettability and Oil-Water Separation.

    Science.gov (United States)

    Su, Xiaojing; Li, Hongqiang; Lai, Xuejun; Zhang, Lin; Liang, Tao; Feng, Yuchun; Zeng, Xingrong

    2017-01-25

    Functional surfaces for reversibly switchable wettability and oil-water separation have attracted much interest with pushing forward an immense influence on fundamental research and industrial application in recent years. This article proposed a facile method to fabricate superhydrophobic surfaces on steel substrates via electroless replacement deposition of copper sulfate (CuSO 4 ) and UV curing of vinyl-terminated polydimethylsiloxane (PDMS). PDMS-based superhydrophobic surfaces exhibited water contact angle (WCA) close to 160° and water sliding angle (WSA) lower than 5°, preserving outstanding chemical stability that maintained superhydrophobicity immersing in different aqueous solutions with pH values from 1 to 13 for 12 h. Interestingly, the superhydrophobic surface could dramatically switch to the superhydrophilic state under UV irradiation and then gradually recover to the highly hydrophobic state with WCA at 140° after dark storage. The underlying mechanism was also investigated by scanning electron microscopy, Fourier transform infrared spectroscopy, and X-ray photoelectron spectroscopy. Additionally, the PDMS-based steel mesh possessed high separation efficiency and excellent reusability in oil-water separation. Our studies provide a simple, fast, and economical fabrication method for wettability-transformable superhydrophobic surfaces and have the potential applications in microfluidics, the biomedical field, and oil spill cleanup.

  2. Smart surfaces with switchable superoleophilicity and superoleophobicity in aqueous media: Toward controllable oil/water separation

    KAUST Repository

    Zhang, L.; Zhang, Z.; Wang, Peng

    2012-01-01

    Advanced materials with surfaces that have controllable oil wettability when submerged in aqueous media have great potential for various underwater applications. Here we have developed smart surfaces on commonly used materials, including non

  3. Separation of density and viscosity influence on liquid-loaded surface acoustic wave devices

    Science.gov (United States)

    Herrmann, F.; Hahn, D.; Büttgenbach, S.

    1999-05-01

    Love-mode sensors are reported for separate measurement of liquid density and viscosity. They combine the general merits of Love-mode devices, e.g., ease of sensitivity adjustment and robustness, with a highly effective procedure of separate determination of liquid density and viscosity. A model is proposed to describe the frequency response of the devices to liquid loading. Moreover, design rules are given for further optimization and sensitivity enhancement.

  4. Fabrication of a novel superhydrophobic and superoleophilic surface by one-step electrodeposition method for continuous oil/water separation

    Science.gov (United States)

    Xiang, Meisu; Jiang, Meihuizi; Zhang, Yanzong; Liu, Yan; Shen, Fei; Yang, Gang; He, Yan; Wang, Lilin; Zhang, Xiaohong; Deng, Shihuai

    2018-03-01

    A novel superhydrophobic and superoleophilic surface was fabricated by one-step electrodeposition on stainless steel meshes, and the durability and oil/water separation properties were assessed. Field emission scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), fourier transform infrared spectroscopy (FT-IR) and optical contact angle measurements were used to characterize surface morphologies, chemical compositions, and wettabilities, respectively. The results indicated that the as-prepared mesh preformed excellent superhydrophobicity and superoleophilicity with a high water contact angle (WCA) of 162 ± 1° and oil contact angle of (OCA) 0°. Meanwhile, the as-prepared mesh also exhibited continuous separation capacity of many kinds of oil/water mixtures, and the separation efficiency for lubrication oil/water mixture was about 98.6%. In addition, after 10 separation cycles, the as-prepared mesh possessed the WCAs of 155 ± 2°, the OCAs of 0° and the separation efficiency of 97.8% for lubrication oil/water mixtures. The as-prepared mesh also retained superhydrophobic and superoleophilic properties after abrading, immersing in salt solutions and different pH solutions.

  5. EXPERIMENTAL DESIGN AND RESPONSE SURFACE MODELING OF PI/PES-ZEOLITE 4A MIXED MATRIX MEMBRANE FOR CO2 SEPARATION

    Directory of Open Access Journals (Sweden)

    T. D. KUSWORO

    2015-09-01

    Full Text Available This paper investigates the effect of preparation of polyimide/polyethersulfone (PI/PES blending-zeolite mixed matrix membrane through the manipulation of membrane production variables such as polymer concentration, blending composition and zeolite loading. Combination of central composite design and response surface methodology were applied to determine the main effect and interaction effects of these variables on membrane separation performance. The quadratic models between each response and the independent parameters were developed and the response surface models were tested with analysis of variance (ANOVA. In this study, PI/ (PES–zeolite 4A mixed matrix membranes were casted using dry/wet phase inversion technique. The separation performance of mixed matrix membrane had been tested using pure gases such as CO2 and CH4. The results showed that zeolite loading was the most significant variable that influenced the CO2/CH4 selectivity among three variables and the experimental results were in good agreement with those predicted by the proposed regression models. The gas separation performance of the membrane was relatively higher as compare to polymeric membrane. Therefore, combination of central composite design and response surface methodology can be used to prepare optimal condition for mixed matrix membrane fabrication. The incorporation of 20 wt% zeolite 4A into 25 wt% of PI/PES matrix had resulted in a high separation performance of membrane material.

  6. Microscale anechoic architecture: acoustic diffusers for ultra low power microparticle separation via traveling surface acoustic waves.

    Science.gov (United States)

    Behrens, Jan; Langelier, Sean; Rezk, Amgad R; Lindner, Gerhard; Yeo, Leslie Y; Friend, James R

    2015-01-07

    We present a versatile and very low-power traveling SAW microfluidic sorting device able to displace and separate particles of different diameter in aqueous suspension; the travelling wave propagates through the fluid bulk and diffuses via a Schröder diffuser, adapted from its typical use in concert hall acoustics to be the smallest such diffuser to be suitable for microfluidics. The effective operating power range is two to three orders of magnitude less than current SAW devices, uniquely eliminating the need for amplifiers, and by using traveling waves to impart forces directly upon suspended microparticles, they can be separated by size.

  7. Ion chromatography separation of cotton surface melezitose and raffinose: entomological vs. plant sugars

    Science.gov (United States)

    According to previous studies, certain levels of the carbohydrates melezitose and trehalulose deposited on the surface of cotton are indicative of either whitefly or aphid contamination, which may cause problems during cotton processing. Obtaining reliable IC values for those surface sugars is para...

  8. Surface hardening of optic materials by deposition of diamond like carbon coatings from separated plasma of arc discharge

    Science.gov (United States)

    Osipkov, A. S.; Bashkov, V. M.; Belyaeva, A. O.; Stepanov, R.; Mironov, Y. M.; Galinovsky, A. L.

    2015-02-01

    This article considers the issue of strengthening of optic materials used in the IR spectrum by deposition of diamond like carbon coatings from separated plasma arc discharge. The report shows results of tests of bare and strengthened optical materials such as BaF2, MgF2, Si, Ge, including the testing of their strength and spectral characteristics. Results for the determination of optical constants for the DLC coatings deposited on substrates of Ge and Si, by using separated plasma, are also presented. Investigations showed that surface hardening of optical materials operable in the IR range, by the deposition of diamond like carbon coating onto their surface, according to this technology, considerably improves operational properties and preserves or improves their optic properties.

  9. Role of nanoparticles in phase separation and final morphology of superhydrophobic polypropylene/zinc oxide nanocomposite surfaces

    Energy Technology Data Exchange (ETDEWEB)

    Hejazi, Iman [Department of Polymer Engineering and Color Technology, Amirkabir University of Technology, Tehran (Iran, Islamic Republic of); Hajalizadeh, Bardia [Department of Chemical Engineering, Islamic Azad University, Shahrood Branch, P.O. Box 36155-163, Shahrood (Iran, Islamic Republic of); Seyfi, Javad, E-mail: Jseyfi@gmail.com [Department of Chemical Engineering, Islamic Azad University, Shahrood Branch, P.O. Box 36155-163, Shahrood (Iran, Islamic Republic of); Sadeghi, Gity Mir Mohamad [Department of Polymer Engineering and Color Technology, Amirkabir University of Technology, Tehran (Iran, Islamic Republic of); Jafari, Seyed-Hassan [School of Chemical Engineering, University of Tehran, P.O. Box 11155-4563, Tehran (Iran, Islamic Republic of); Khonakdar, Hossein Ali [Iran Polymer and Petrochemical Institute, P.O. Box 14965/115, Tehran (Iran, Islamic Republic of)

    2014-02-28

    In this work, phase separation process was revisited to study the effect of nanoparticles in acceleration of phase separation and formation of hierarchical structures. Superhydrophobic surfaces were prepared using polypropylene (PP) and the corresponding nanocomposites containing zinc oxide (ZnO) nanoparticles through a typical solution casting method. The wettability and morphological behavior of the surfaces were investigated via water contact angle (WCA) measurements and scanning electron microscopy (SEM), respectively. It was found that upon introduction of ZnO nanoparticles into the pure PP, the obtained surfaces have become superhydrophobic with WCAs above 150° and sliding angles below 10°. Calcination of ZnO nanoparticles was exploited to explicate the unexpected significant loss in superhydrophobicity of the sample loaded with high ZnO content. Crystallization behavior of the samples were also investigated via differential scanning calorimetry and correlated to superhydrophobicity of the surfaces. X-ray photoelectron and Fourier transform infrared spectroscopies were also utilized to further characterize the samples. An attempt was also made to present a more clear mechanism for formation of hierarchical structures which are responsible for superhydrophobicity. Likewise, the so far proposed mechanisms for formation of micro/nano roughness on the superhydrophobic surfaces were reviewed as well.

  10. Renewable enthusiasm

    International Nuclear Information System (INIS)

    Duffin, Tony

    2000-01-01

    A reduction in energy consumption by the energy intensive sectors will be rewarded by a tax credit. The advantages of renewable sources of energy in terms of reducing emissions of carbon dioxide are extolled. The Government will reward the use of renewables through exemption from the Climate Change Levy. Many major companies are now committed to renewables and Shell predict that 50% of world energy will come from renewables by 2050. World-wide there is now 10,000 MW of installed wind power and the annual rate of growth is more than 20%. Other renewables such as biomass, energy from waste, solar power, hydropower, wind power and tidal power are discussed. The Government would like to see 10% of the UK's electricity coming from renewables by 2010. (UK)

  11. Surface treatment with Fenton for separation of acrylonitrile-butadiene-styrene and polyvinylchloride waste plastics by flotation.

    Science.gov (United States)

    Wang, Jian-Chao; Wang, Hui; Huang, Luo-Luo; Wang, Chong-Qing

    2017-09-01

    Surface treatment with Fenton was applied to flotation separation of acrylonitrile-butadienestyrene (ABS) and polyvinylchloride (PVC). After treatment, the floatability of ABS has a dramatic decrease, while the floatability of PVC is not affected. Fourier transform infrared spectroscopy (FT-IR) spectra and X-ray photoelectron spectroscopy (XPS) spectra were recorded to ascertain the mechanism of Fenton treatment. FT-IR and XPS analysis confirms that the introduction of oxygen-containing group occurs on the surface of ABS. The optimum conditions are molar ration (H 2 O 2 :Fe 2+ ) 10000, H 2 O 2 concentration 0.4M/L, pH 5.8, treatment time 2min and temperature 25°C, frother concentration 15mg/L and flotation time 3min. Particle sizes and mixing ratios were also investigated. Plastic mixtures of ABS and PVC with different particle sizes and mixing ratios can be effectively separated. The purity of ABS and PVC are up to 100% and 99.78%, respectively; the recovery of ABS and PVC are up to 99.89% and 100%, respectively. A practical, environmentally friendly and effective reagent, namely Fenton, was originally applied to surface treatment of ABS and PVC waste plastics for flotation separation of their mixtures. Copyright © 2017 Elsevier Ltd. All rights reserved.

  12. Renewable energy

    International Nuclear Information System (INIS)

    Yoon, Cheon Seok

    2009-09-01

    This book tells of renewable energy giving description of environment problem, market of renewable energy and vision and economics of renewable energy. It also deals with solar light like solar cell, materials performance, system and merit of solar cell, solar thermal power such as solar cooker and solar collector, wind energy, geothermal energy, ocean energy like tidal power and ocean thermal energy conversion, fuel cell and biomass.

  13. Quantifying the resolution level where the GRACE satellites can separate Greenland's glacial mass balance from surface mass balance

    Science.gov (United States)

    Bonin, J. A.; Chambers, D. P.

    2015-09-01

    Mass change over Greenland can be caused by either changes in the glacial dynamic mass balance (DMB) or the surface mass balance (SMB). The GRACE satellite gravity mission cannot directly separate the two physical causes because it measures the sum of the entire mass column with limited spatial resolution. We demonstrate one theoretical way to indirectly separate cumulative SMB from DMB with GRACE, using a least squares inversion technique with knowledge of the location of the glaciers. However, we find that the limited 60 × 60 spherical harmonic representation of current GRACE data does not provide sufficient resolution to adequately accomplish the task. We determine that at a maximum degree/order of 90 × 90 or above, a noise-free gravity measurement could theoretically separate the SMB from DMB signals. However, current GRACE satellite errors are too large at present to separate the signals. A noise reduction of a factor of 10 at a resolution of 90 × 90 would provide the accuracy needed for the interannual cumulative SMB and DMB to be accurately separated.

  14. Interfacial separation of a mature biofilm from a glass surface - A combined experimental and cohesive zone modelling approach.

    Science.gov (United States)

    Safari, Ashkan; Tukovic, Zeljko; Cardiff, Philip; Walter, Maik; Casey, Eoin; Ivankovic, Alojz

    2016-02-01

    A good understanding of the mechanical stability of biofilms is essential for biofouling management, particularly when mechanical forces are used. Previous biofilm studies lack a damage-based theoretical model to describe the biofilm separation from a surface. The purpose of the current study was to investigate the interfacial separation of a mature biofilm from a rigid glass substrate using a combined experimental and numerical modelling approach. In the current work, the biofilm-glass interfacial separation process was investigated under tensile and shear stresses at the macroscale level, known as modes I and II failure mechanisms respectively. The numerical simulations were performed using a Finite Volume (FV)-based simulation package (OpenFOAM®) to predict the separation initiation using the cohesive zone model (CZM). Atomic force microscopy (AFM)-based retraction curve was used to obtain the separation properties between the biofilm and glass colloid at microscale level, where the CZM parameters were estimated using the Johnson-Kendall-Roberts (JKR) model. In this study CZM is introduced as a reliable method for the investigation of interfacial separation between a biofilm and rigid substrate, in which a high local stress at the interface edge acts as an ultimate stress at the crack tip.This study demonstrated that the total interfacial failure energy measured at the macroscale, was significantly higher than the pure interfacial separation energy obtained by AFM at the microscale, indicating a highly ductile deformation behaviour within the bulk biofilm matrix. The results of this study can significantly contribute to the understanding of biofilm detachments. Copyright © 2015 Elsevier Ltd. All rights reserved.

  15. Fabrication of superhydrophobic copper surface on various substrates for roll-off, self-cleaning, and water/oil separation.

    Science.gov (United States)

    Sasmal, Anup Kumar; Mondal, Chanchal; Sinha, Arun Kumar; Gauri, Samiran Sona; Pal, Jaya; Aditya, Teresa; Ganguly, Mainak; Dey, Satyahari; Pal, Tarasankar

    2014-12-24

    Superhydrophobic surfaces prevent percolation of water droplets and thus render roll-off, self-cleaning, corrosion protection, etc., which find day-to-day and industrial applications. In this work, we developed a facile, cost-effective, and free-standing method for direct fabrication of copper nanoparticles to engender superhydrophobicity for various flat and irregular surfaces such as glass, transparency sheet (plastic), cotton wool, textile, and silicon substrates. The fabrication of as-prepared superhydrophobic surfaces was accomplished using a simple chemical reduction of copper acetate by hydrazine hydrate at room temperature. The surface morphological studies demonstrate that the as-prepared surfaces are rough and display superhydrophobic character on wetting due to generation of air pockets (The Cassie-Baxter state). Because of the low adhesion of water droplets on the as-prepared surfaces, the surfaces exhibited not only high water contact angle (164 ± 2°, 5 μL droplets) but also superb roll-off and self-cleaning properties. Superhydrophobic copper nanoparticle coated glass surface uniquely withstands water (10 min), mild alkali (5 min in saturated aqueous NaHCO3 of pH ≈ 9), acids (10 s in dilute HNO3, H2SO4 of pH ≈ 5) and thiol (10 s in neat 1-octanethiol) at room temperature (25-35 °C). Again as-prepared surface (cotton wool) was also found to be very effective for water-kerosene separation due to its superhydrophobic and oleophilic character. Additionally, the superhydrophobic copper nanoparticle (deposited on glass surface) was found to exhibit antibacterial activity against both Gram-negative and Gram-positive bacteria.

  16. Facile Synthesis of Flexible Methylsilsesquioxane Aerogels with Surface Modifications for Sound- Absorbance, Fast Dye Adsorption and Oil/Water Separation

    Directory of Open Access Journals (Sweden)

    Xingzhong Guo

    2018-04-01

    Full Text Available New flexible methylsilsesquioxane (MSQ aerogels have been facilely prepared by a sol–gel process with methyltrimethoxysilane (MTMS and dimethyldimethoxysilane (DMDMS as co-precursors, followed by surface modification and ambient pressure drying. The microstructure, mechanical properties and hydrophobicity of these MSQ aerogels after surface modifications of hexamethyldisiloxane (HMDSO and/or hexamethyldisilazane (HMDS were investigated in detail, and the applications of surface-modified MSQ aerogels in sound-absorbance, fast dye adsorption and oil/water separation were evaluated, respectively. The MSQ aerogels surface-modified by HMDS possess flexibility, elasticity and superhydrophobicity, and demonstrate good performance in the mentioned applications. The resultant MSQ aerogel used in sound-absorbance has high frequency (about 6 kHz acoustic absorptivity of up to 80%, benefiting from its macroporous structure and porosity of 94%, and it also possesses intermediate frequency acoustic absorptivity (about 1 kHz up to 80% owing to its elasticity. This MSQ aerogel can selectively separate oil from oil/water mixtures with high efficiency due to its superhydrophobicity and superlipophilicity, resulting from a lot of methyl groups, density as low as 0.12 cm3·g−1 and a water contact angle as high as 157°. This MSQ aerogel can be assembled to be a monolithic column applied for fast dye adsorption, and shows selective adsorption for anionic dyes and removal efficiency of methyl orange of up to 95%.

  17. Corrugation of Phase-Separated Lipid Bilayers Supported by Nanoporous Silica Xerogel Surfaces

    Energy Technology Data Exchange (ETDEWEB)

    Goksu, E I; Nellis, B A; Lin, W; Satcher Jr., J H; Groves, J T; Risbud, S H; Longo, M L

    2008-10-30

    Lipid bilayers supported by substrates with nanometer-scale surface corrugations holds interest in understanding both nanoparticle-membrane interactions and the challenges of constructing models of cell membranes on surfaces with desirable properties, e.g. porosity. Here, we successfully form a two-phase (gel-fluid) lipid bilayer supported by nanoporous silica xerogel. Surface topology, diffusion, and lipid density in comparison to mica-supported lipid bilayers were characterized by AFM, FRAP, FCS, and quantitative fluorescence microscopy, respectively. We found that the two-phase lipid bilayer follows the xerogel surface contours. The corrugation imparted on the lipid bilayer results in a lipid density that is twice that on a flat mica surface. In direct agreement with the doubling of actual bilayer area in a projected area, we find that the lateral diffusion coefficient (D) of lipids on xerogel ({approx}1.7 {micro}m{sup 2}/s) is predictably lower than on mica ({approx}4.1 {micro}m{sup 2}/s) by both FRAP and FCS techniques. Furthermore, the gel-phase domains on xerogel compared to mica were larger and less numerous. Overall, our results suggest the presence of a relatively defect-free continuous two-phase bilayer that penetrates approximately midway into the first layer of {approx}50 nm xerogel beads.

  18. Finite element method for starved hydrodynamic lubrication with film separation and free surface effects

    DEFF Research Database (Denmark)

    Poulios, Konstantinos; Vølund, Anders; Klit, Peder

    2018-01-01

    This paper proposes a numerical method for determining the evolution of lubricant film thickness and pressure in partially and fully flooded regions of a hydrodynamic contact between two non-conformal rigid surfaces. The proposed method accounts for the classical Reynolds equation within the fully...... thickness is zero. Both pressure and film thickness fields are considered as unknowns to solve for in each time step and they are approximated through quadratic B-spline finite elements. The geometry of the gap between the rigid surfaces delimiting the lubricant is accounted for in the form of a unilateral...

  19. Electrochemical separation and isotopic determination of thallium at the nanogram level by surface ionisation mass spectrometry

    International Nuclear Information System (INIS)

    Arden, J.W.

    1983-01-01

    A rapid low-blank procedure is described for the co-separation of thallium and lead by sequential cathodic and anodic electrodeposition from natural samples, especially complex natural silicates, for subsequent mass spectrometry. A micro anion-exchange procedure is also described for the separation of thallium and lead. Ion currents of 10 - 10 A can be obtained from 1 ng of thallium. The isotopic composition of 1 ng of thallium can be measured on a Faraday detector with a precision of 0.05-0.1%. The total procedural blank is 3 pg. By using stable isotope dilution, 0.2 ng of thallium can be measured with a precision of 0.6% with only a 2% blank correction. This allows the accurate determination of thallium in natural samples down to concentration levels of about 50 pg g - 1 . The detection limit is 50 fg. This procedure has been applied to meteorites and terrestrial rocks. The stable isotope dilution technique is suitable for geochemical, environmental and toxicological studies requiring a highly sensitive, accurate and precise method for the determination of thallium. (Auth.)

  20. License renewal

    International Nuclear Information System (INIS)

    Newberry, S.

    1993-01-01

    This article gives an overview of the process of license renewal for nuclear power plants. It explains what is meant by license renewal, the significance of license renewal, and goes over key elements involved in the process of license renewal. Those key elements are NRC requirements embodied in 10 CFR Part 54 (Reactor Safety) and 10 CFR Part 51 (Environmental Issues). In addition Industry Reports must be developed and reviewed. License renewal is essentially the process of applying for a 20 year extension to the original 40 year operating license granted for the plant. This is a very long term process, which involves a lot of preparation, and compliance with regulatory rules and guidelines. In general it is a process which is expected to begin when plants reach an operating lifetime of 20 years. It has provisions for allowing the public to become involved in the review process

  1. Renewable Energy

    DEFF Research Database (Denmark)

    Sørensen, Bent Erik

    Bent Sorensen’s Renewable Energy: Physics, Engineering, Environmental Impacts, Economics and Planning, Fifth Edition, continues the tradition by providing a thorough and current overview of the entire renewable energy sphere. Since its first edition, this standard reference source helped put...... renewable energy on the map of scientific agendas. Several renewable energy solutions no longer form just a marginal addition to energy supply, but have become major players, with the promise to become the backbone of an energy system suitable for life in the sustainability lane. This volume is a problem...... structured around three parts in order to assist readers in focusing on the issues that impact them the most for a given project or question. PART I covers the basic scientific principles behind all major renewable energy resources, such as solar, wind, and biomass. PART II provides in-depth information...

  2. Response Surface Optimized Extraction of 1-Deoxynojirimycin from Mulberry Leaves (Morus alba L. and Preparative Separation with Resins

    Directory of Open Access Journals (Sweden)

    Teng Wang

    2014-05-01

    Full Text Available In the present study, the extraction technology and preparative separation of 1-deoxynojirimycin from mulberry leaves were systematically investigated. Four extraction parameters (ethanol concentration, extraction temperature, extraction time and ratio of solvent to sample were explored by response surface methodology (RSM. The results indicated that the maximal yield of 1-deoxynojirimycin was achieved with an ethanol concentration of 55%, extraction temperature of 80 °C, extraction time of 1.2 h and ratio of solvent to sample of 12:1. The extraction yield under these optimum conditions was found to be 256 mg/100 g dry mulberry leaves. A column packed with a selected resin was used to perform dynamic adsorption and desorption tests to optimize the separation process. The results show that the preparative separation of 1-deoxynojirimycin from mulberry leaves can be easily and effectively done by adopting 732 resin. In conclusion, 732 resin is the most appropriate for the separation of 1-deoxynojirimycin from other components in mulberry leaves extracts, and its adsorption behavior can be described with Langmuir isotherms and a two-step adsorption kinetics model. The recovery and purity of 1-deoxynojirimycin in the final product were 90.51% and 15.3%, respectively.

  3. Land Surface Temperature and Emissivity Separation from Cross-Track Infrared Sounder Data with Atmospheric Reanalysis Data and ISSTES Algorithm

    Directory of Open Access Journals (Sweden)

    Yu-Ze Zhang

    2017-01-01

    Full Text Available The Cross-track Infrared Sounder (CrIS is one of the most advanced hyperspectral instruments and has been used for various atmospheric applications such as atmospheric retrievals and weather forecast modeling. However, because of the specific design purpose of CrIS, little attention has been paid to retrieving land surface parameters from CrIS data. To take full advantage of the rich spectral information in CrIS data to improve the land surface retrievals, particularly the acquisition of a continuous Land Surface Emissivity (LSE spectrum, this paper attempts to simultaneously retrieve a continuous LSE spectrum and the Land Surface Temperature (LST from CrIS data with the atmospheric reanalysis data and the Iterative Spectrally Smooth Temperature and Emissivity Separation (ISSTES algorithm. The results show that the accuracy of the retrieved LSEs and LST is comparable with the current land products. The overall differences of the LST and LSE retrievals are approximately 1.3 K and 1.48%, respectively. However, the LSEs in our study can be provided as a continuum spectrum instead of the single-channel values in traditional products. The retrieved LST and LSEs now can be better used to further analyze the surface properties or improve the retrieval of atmospheric parameters.

  4. In situ Silver Spot Preparation and on-Plate Surface-Enhanced Raman Scattering Detection in Thin Layer Chromatography Separation

    Science.gov (United States)

    Herman, K.; Mircescu, N. E.; Szabo, L.; Leopold, L. F.; Chiş, V.; Leopold, N.

    2013-05-01

    An improved approach for surface-enhanced Raman scattering (SERS) detection of mixture constituents after thin layer chromatography (TLC) separation is presented. A SERS active silver substrate was prepared under open air conditions, directly on the thin silica film by photo-reduction of silver nitrate, allowing the detection of binary mixtures of cresyl violet, bixine, crystal violet, and Cu(II) complex of 4-(2-pyridylazo)resorcinol. The recorded SERS spectrum provides a unique spectral fingerprint for each molecule; therefore the use of analyte standards is avoided, thus rendering the presented procedure advantageous compared to the conventional detection methodology in TLC.

  5. Fabrication of stable and durable superhydrophobic surface on copper substrates for oil-water separation and ice-over delay.

    Science.gov (United States)

    Guo, Jie; Yang, Fuchao; Guo, Zhiguang

    2016-03-15

    We report a simple and rapid method to fabricate superhydrophobic films on copper substrates via Fe(3+) etching and octadecanethiol (ODT) modification. The etching process can be as short as 5 min and the ODT treatment only takes several seconds. In addition, the whole process is quite flexible in reaction time. The superhydrophobicity of as-prepared surfaces is mechanically durable and chemically stable, which have great performance in oil-water separation and ice-over resistance. Copyright © 2015 Elsevier Inc. All rights reserved.

  6. Renewable energy

    International Nuclear Information System (INIS)

    Berghmans, J.

    1994-01-01

    Renewable energy sources have a small environmental impact and can be easily integrated within existing structures. Moreover, the use of renewable energy sources can contribute to achieve a zero emission of carbon dioxide by 2100, provided an efficient environmental policy during the next 40 years. This includes a correct pricing policy of renewable energy sources with respect to nuclear energy and fossil fuel. The latter energy sources have been favoured in the past. In addition, an open market policy, the restructuring or conversion of existing international energy institutes, and international treaties for the protection of the natural environment are needed in view of achieving the zero carbon dioxide emission objective. (A.S.)

  7. Development of Surfaces Optically Suitable for Flat Solar Panels. [using a reflectometer which separately evaluates spectral and diffuse reflectivities of surfaces

    Science.gov (United States)

    1979-01-01

    A reflectometer which can separately evaluate the spectral and diffuse reflectivities of surfaces is described. A phase locked detection system for the reflectometer is also described. A selective coating on aluminum potentially useful for flat plate solar collector applications is presented. The coating is composed of strongly bound copper oxide (divalent) and is formed by an etching process performed on an aluminum alloy with high copper content. Fabrication costs are expected to be small due to the one stop fabrication process. A number of conclusions gathered from the literature as to the required optical properties of flat plate solar collectors are discussed.

  8. A separator

    Energy Technology Data Exchange (ETDEWEB)

    Prokopyuk, S.G.; Dyachenko, A.Ye.; Mukhametov, M.N.; Prokopov, O.I.

    1982-01-01

    A separator is proposed which contains separating slanted plates and baffle plates installed at a distance to them at an acute angle to them. To increase the effectiveness of separating a gas and liquid stream and the throughput through reducing the secondary carry away of the liquid drops and to reduce the hydraulic resistance, as well, openings are made in the plates. The horizontal projections of each opening from the lower and upper surfaces of the plate do not overlap each other.

  9. Renewable energy.

    Science.gov (United States)

    Destouni, Georgia; Frank, Harry

    2010-01-01

    The Energy Committee of the Royal Swedish Academy of Sciences has in a series of projects gathered information and knowledge on renewable energy from various sources, both within and outside the academic world. In this article, we synthesize and summarize some of the main points on renewable energy from the various Energy Committee projects and the Committee's Energy 2050 symposium, regarding energy from water and wind, bioenergy, and solar energy. We further summarize the Energy Committee's scenario estimates of future renewable energy contributions to the global energy system, and other presentations given at the Energy 2050 symposium. In general, international coordination and investment in energy research and development is crucial to enable future reliance on renewable energy sources with minimal fossil fuel use.

  10. Effects of low-pressure nitrogen plasma treatment on the surface properties and electrochemical performance of the polyethylene separator used lithium-ion batteries

    Science.gov (United States)

    Li, Chun; Li, Hsiao-Ling; Li, Chi-Heng; Liu, Yu-Shuan; Sung, Yu-Ching; Huang, Chun

    2018-01-01

    In this paper, we describe the surface transition of the polyethylene (PE) separator used in lithium-ion batteries treated by low-pressure nitrogen plasma discharge. The nitrogen-plasma-treated PE separator was characterized by contact angle measurement, Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy, and scanning electron microscopy. The electrochemical performance of the lithium ion batteries fabricated with the nitrogen-plasma-treated separator was also evaluated. Results showed that polar functionalization groups were induced on the PE surface by the nitrogen plasma discharge, causing the surface to become hydrophilic. The increases in surface wettability and surface free energy result in electrolyte retention improvement. Moreover, the nitrogen plasma-treated PE separator leads to superior performance in lithium-ion battery assembly.

  11. Surface phase separation, dewetting feature size, and crystal morphology in thin films of polystyrene/poly(ε-caprolactone) blend.

    Science.gov (United States)

    Ma, Meng; He, Zhoukun; Li, Yuhan; Chen, Feng; Wang, Ke; Zhang, Qing; Deng, Hua; Fu, Qiang

    2012-12-01

    Thin films of polystyrene (PS)/poly(ε-caprolactone) (PCL) blends were prepared by spin-coating and characterized by tapping mode force microscopy (AFM). Effects of the relative concentration of PS in polymer solution on the surface phase separation and dewetting feature size of the blend films were systematically studied. Due to the coupling of phase separation, dewetting, and crystallization of the blend films with the evaporation of solvent during spin-coating, different size of PS islands decorated with various PCL crystal structures including spherulite-like, flat-on individual lamellae, and flat-on dendritic crystal were obtained in the blend films by changing the film composition. The average distance of PS islands was shown to increase with the relative concentration of PS in casting solution. For a given ratio of PS/PCL, the feature size of PS appeared to increase linearly with the square of PS concentration while the PCL concentration only determined the crystal morphology of the blend films with no influence on the upper PS domain features. This is explained in terms of vertical phase separation and spinodal dewetting of the PS rich layer from the underlying PCL rich layer, leading to the upper PS dewetting process and the underlying PCL crystalline process to be mutually independent. Copyright © 2012 Elsevier Inc. All rights reserved.

  12. Simple and Green Fabrication of a Superhydrophobic Surface by One-Step Immersion for Continuous Oil/Water Separation.

    Science.gov (United States)

    Zhu, Jingfang; Liu, Bin; Li, Longyang; Zeng, Zhixiang; Zhao, Wenjie; Wang, Gang; Guan, Xiaoyan

    2016-07-21

    In this paper, stainless steel meshes with superhydrophobic and superoleophilic surfaces were fabricated by rapid and simple one-step immersion in a solution containing hydrochloric acid and stearic acid. The apparent contact angles were tested by a video contact angle measurement system (CA). Field emission scanning electron microscopy (FE-SEM), Fourier transform infrared spectroscopy (FTIR), and X-ray photoelectron spectroscopy (XPS) were conducted to characterize the surface topographies and chemical compositions. The SEM results showed that mesh surfaces were covered by ferric stearate (Fe[CH3(CH2)16COO]2) with low surface energy. The CA test results showed that the mesh had a maximum apparent contact angle of 160 ± 1.0° and a sliding angle of less than 5.0° for the water droplet, whereas the apparent contact angle for the oil droplet was zero. Ultrasound oscillation and exposure tests at atmospheric conditions and immersion tests in 3.5 wt % NaCl aqueous solution were conducted to confirm the mesh with excellent superhydrophobic and superoleophilic properties. On the basis of the superhydrophobic mesh, a miniature separation device pump was designed to collect pure oil from the oil/water mixture. It showed that the device was easier and convenient. The techniques and materials presented in this work are promising for application to wastewater and oil spill treatment.

  13. Spent coffee-based activated carbon: specific surface features and their importance for H2S separation process.

    Science.gov (United States)

    Kante, Karifala; Nieto-Delgado, Cesar; Rangel-Mendez, J Rene; Bandosz, Teresa J

    2012-01-30

    Activated carbons were prepared from spent ground coffee. Zinc chloride was used as an activation agent. The obtained materials were used as a media for separation of hydrogen sulfide from air at ambient conditions. The materials were characterized using adsorption of nitrogen, elemental analysis, SEM, FTIR, and thermal analysis. Surface features of the carbons depend on the amount of an activation agent used. Even though the residual inorganic matter takes part in the H(2)S retention via salt formation, the porous surface of carbons governs the separation process. The chemical activation method chosen resulted in formation of large volume of pores with sizes between 10 and 30Å, optimal for water and hydrogen sulfide adsorption. Even though the activation process can be optimized/changed, the presence of nitrogen in the precursor (caffeine) is a significant asset of that specific organic waste. Nitrogen functional groups play a catalytic role in hydrogen sulfide oxidation. Copyright © 2011 Elsevier B.V. All rights reserved.

  14. Preparation of a surface-grafted imprinted ceramic membrane for selective separation of molybdate anion from water solutions.

    Science.gov (United States)

    Zeng, Jianxian; Dong, Zhihui; Zhang, Zhe; Liu, Yuan

    2017-07-05

    A surface-grafted imprinted ceramic membrane (IIP-PVI/CM) for recognizing molybdate (Mo(VI)) anion was prepared by surface-initiated graft-polymerization. Firstly, raw alumina ceramic membrane (CM) was deposited with SiO 2 active layer by situ hydrolysis deposition method. Subsequently, γ-methacryloxy propyl trimethoxyl silane (MPS) was used as a coupling agent to introduce double bonds onto the SiO 2 layer (MPS-CM). Then, 1-vinylimidazole (VI) was employed as a functional monomer to graft-polymerization onto the MPS-CM (PVI-CM). During the graft-polymerization, the influence factors of grafting degree of PVI were investigated in detail. Under optimum conditions (monomer concentration 20wt%, temperature 70°C, initiator amount 1.1wt% and reaction time 8h), the grafting degree of 20.39g/100g was obtained. Further, Mo(VI) anion was used as a template to imprint in the PVI-CM by employing 1,6-dibromohexane as a cross-linking agent, and then Mo(VI) was removed, obtaining the IIP-PVI/CM with many imprinted cavities for Mo(VI). Thereafter, static adsorption and dynamic separation properties of IIP-PVI/CM for Mo(VI) were studied. Results indicate that IIP-PVI/CM shows a specific selectivity for Mo(VI) with the adsorption capacity of 0.69mmol/100g, and the selectivity coefficient of IIP-PVI/CM is 7.48 for molybdate to tungstate anions. During the dynamic separation, IIP-PVI/CM has also good selectivity for separation of Mo(VI) and W(VI) anions. Copyright © 2017 Elsevier B.V. All rights reserved.

  15. Comparing Methods of Separating Bacterial Biofilms on the Surface of Water Transportation Pipes and Equipment of Milking in the Farms

    Directory of Open Access Journals (Sweden)

    setareh nabizadeh

    2016-08-01

    Full Text Available Introduction Bacterial biofilms can be both useful and harmful based on their combination and locations. Biofilm formation occurs as a stepwise process. Their formation in liquid transportation pipes used for milking system and drinking water in animal farms may create some problems and is a potential source of pollution. Speed of biofilm formation depends on many factors including: construction and functional characteristics of bacteria, the composition and culture conditions such as temperature and substratum. In this research the Bacillus subtillis bacteria with special characteristics was selected due to its capability for biofilm creation. Bacillus subtillis bacteria is mobility and a stronger connection than other bacteria levels are created. In the research conducted in the biofilm there are many resources on biofilm formation by Bacillus subtillis bacteria. Bacillus subtillis is saprophytic in the soil, water and air. There is also the ability to form spores of Bacillus subtillis. Materials and Methods Firstly the possibility of creating biofilms on different Plastic (polyvinilchlorid, polypropylene, polyethylengelycole, alluminum and glass surfaces in three temperatures of 4°C, 30°C and 37°C were studied. Two different methods of biofilms separation including separating swap and vortex were tested and their efficienceies were calculated. After biofilm formation on parts of the vortex separation method after washing parts in sterile conditions in a tube containing normal saline for 4 minutes was vortex. The bacterial suspension decreasing dilution series was created. Pour plate in medium using agar plate count agar and was cultured at 30°C for 24-48 hours. Numbers of colonies were counted. The numbers of biofilm cells were calculated. In swap method after biofilm formation on parts using a cotton swap was isolated biofilms. The swap was transferred to tube containing normal saline and the bacterial suspension decreasing dilution

  16. The shape of a hole and that of the surface-with-hole cannot be analyzed separately.

    Science.gov (United States)

    Bertamini, Marco; Helmy, Mai Salah

    2012-08-01

    Figure-ground organization has a central role in visual perception, since it creates the regions to which properties, such as shape descriptions, are then assigned. However, there is disagreement on how much shape analysis is independent of figure-ground. The reversal of figure-ground of a single closed region is the purest form of figure-ground organization, and the two resulting percepts are that of an object and that of a hole. Both object and hole are nonaccidental regions and can share an identical outline. We devised a test of how figure-ground and contour ownership dramatically affect how shape is processed. Observers judged the shape of a contour that could be either the same as or different from an irrelevant surrounding contour. We report that different (incongruent) inside and outside contours produce a stronger interference effect when they form a single object-with-hole, as compared with a hierarchical set of surfaces or a single hole separating different surfaces (a trench). We conclude that (1) which surface owns the contour constrains the interference between shapes and that (2) despite some recent claims, holes do not display objectlike properties.

  17. Separation followed by direct SERS detection of explosives on a novel black silicon multifunctional nanostructured surface prepared in a microfluidic channel

    DEFF Research Database (Denmark)

    Talian, Ivan; Hübner, Jörg

    2013-01-01

    The article describes the multifunctionality of a novel black silicon (BS) nanostructured surface covered with a thin layer of noble metal prepared in the a microfluidic channel. It is focused on the separation properties of the BS substrate with direct detection of the separated analytes utilizing...

  18. Renewable energy

    DEFF Research Database (Denmark)

    Olsen, Birgitte Egelund

    2016-01-01

    Renewable energy projects are increasingly confronted by local opposition, which delays and sometimes even prevents their implementation. This reflects the frequent gap between support for the general idea of renewables as a strategy for reducing carbon emissions, and acceptance of renewable energy...... installations in the local landscape. A number of countries have introduced financial incentives to promote community acceptance. The tool box of incentives is still limited but in recent years it has been expanded to address local concerns. Certain general characteristics can be identified, suggesting...... that there are at least three distinct categories of incentives: individual compensation, community benefits and ownership measures. Local opposition must be approached with caution, as financial incentives to promote local acceptance can be seen as buying consent or even ‘bribery’, stirring up further opposition....

  19. Organic photochemical reactions on solid surfaces: Enrichment and separation of isotopes. Final report. SBIR-1988, Phase 2

    International Nuclear Information System (INIS)

    Ruderman, W.; Fehlner, J.; Spencer, J.

    1988-01-01

    The objectives of the Phase II program were to: (1) investigate organic photochemical reactions on solid porous silica surfaces, (2) utilize the magnetic isotope effect to develop a (13)C enrichment process using a fluidized bed reactor, and (3) investigate the possibility of enrichment of heavier isotopes having a nuclear spin. Although researchers were able to demonstrate a continuous fluidized bed (13)C enrichment process, analysis showed that the process could not compete with low temperature distillation of CO because of the high cost of the starting material, dibenzylketone (DBK), and the difficulty of converting the photochemical decomposition products back to DBK. However, the process shows promise for the separation of heavier isotopes such as (29)Si. The photochemical studies led to the discovery that the selectivity for terminal chlorination of alkanes can be increased more than 25 fold by sorbing the alkanes on ZSM-5 zeolites in a fluidized bed. The selectivity is ascribed to the presence of interfaces within the crystals

  20. Optimization of methanol crystallization for highly efficient separation of palmitic acid from palm fatty acid mixture using response surface methodology

    Directory of Open Access Journals (Sweden)

    A. A.W. Japir

    2018-01-01

    Full Text Available The objective of the current study was to develop parameters for the separation of palmitic acid (PA from a crude palm oil saturated fatty acid (SFAs mixture by using the methanol crystallization method. The conditions of methanol crystallization were optimized by the response surface methodology (RSM with the D-optimal design. The procedure of developing the solvent crystallization method was based on various different parameters. The fatty acid composition was carried out using a gas chromatography flame ionization detector (GC-FID as fatty acid methyl esters. The highest percentage of SFAs was more than 96% with the percentage yield of 87.5% under the optimal conditions of fatty acids-to-methanol ratio of 1: 20 (w/v, the crystallization temperature of -15 °C, and the crystallization time of 24 hours, respectively. The composition of separated SFAs in the solid fraction contains 96.7% of palmitic acid (C16:0 as a dominant component and 3.3% of stearic acid (C18:0. The results showed that utilizing methanol as a crystallization solvent is recommended because of its high efficiency, low cost, stability, availability, comparative ease of recovery and its ability to form needle-like crystals which have good filtering and washing characteristics.

  1. Optimization of methanol crystallization for highly efficient separation of palmitic acid from palm fatty acid mixture using response surface methodology

    International Nuclear Information System (INIS)

    Japir, A.A.W.; Salimon, J.; Derawi, D.; Yahaya, B.H.; Jamil, M.S.M.; Yusop, M.R.

    2017-01-01

    The objective of the current study was to develop parameters for the separation of palmitic acid (PA) from a crude palm oil saturated fatty acid (SFAs) mixture by using the methanol crystallization method. The conditions of methanol crystallization were optimized by the response surface methodology (RSM) with the D-optimal design. The procedure of developing the solvent crystallization method was based on various different parameters. The fatty acid composition was carried out using a gas chromatography flame ionization detector (GC-FID) as fatty acid methyl esters. The highest percentage of SFAs was more than 96% with the percentage yield of 87.5% under the optimal conditions of fatty acids-to-methanol ratio of 1: 20 (w/v), the crystallization temperature of -15 °C, and the crystallization time of 24 hours, respectively. The composition of separated SFAs in the solid fraction contains 96.7% of palmitic acid (C16:0) as a dominant component and 3.3% of stearic acid (C18:0). The results showed that utilizing methanol as a crystallization solvent is recommended because of its high efficiency, low cost, stability, availability, comparative ease of recovery and its ability to form needle-like crystals which have good filtering and washing characteristics. [es

  2. Renewable Energy

    NARCIS (Netherlands)

    Turkenburg, W.C.; Arent, D.; Bertani, R.; Faaij, A.P.C.; Hand, M.; Krewitt, W.; Larson, E.D.; Lund, J.; Mehos, M.; Merrigan, T.; Mitchell, C.; Moreira, J.R.; Sinke, W.C.; Sonntag-O'Brien, V.; Thresher, B.; Sark, W.G.J.H.M. van; Usher, E.

    2012-01-01

    This chapter presents an in-depth examination of major renewable energy technologies, including their installed capacity and energy supply in 2009 , the current state of market and technology development, their economic and financial feasibility in 2009 and in the near future, as well as major

  3. Unsteady separated stagnation-point flow and heat transfer of a viscous fluid over a moving flat surface

    Science.gov (United States)

    Dholey, S.

    2018-04-01

    In this paper, we have investigated numerically the laminar unsteady separated stagnation-point flow and heat transfer of a viscous fluid over a moving flat surface in the presence of a time dependent free stream velocity which causes the unsteadiness of this flow problem. The plate is assumed to move in the same or opposite direction of the free stream velocity. The flow is therefore governed by the velocity ratio parameter λ (ratio of the plate velocity to the free stream velocity) and the unsteadiness parameter β. When the plate surface moves in the same direction of the free stream velocity (i.e., when λ > 0), the solution of this flow problem continues for any given value of β. On the other hand, when they move in opposite directions (i.e., when λ heat transfer analysis is that for a given value of λ(= 0), first the heat transfer rate increases with the increase of the Prandtl number Pr and after attaining a maximum value, it decreases and finally tends to be zero for large values of Pr depending upon the values of β > 0. On the contrary, for a given value of β(≤ 0), the rate of heat transfer increases consistently with the increase of Pr.

  4. Cell surface engineering of Saccharomyces cerevisiae combined with membrane separation technology for xylitol production from rice straw hydrolysate.

    Science.gov (United States)

    Guirimand, Gregory; Sasaki, Kengo; Inokuma, Kentaro; Bamba, Takahiro; Hasunuma, Tomohisa; Kondo, Akihiko

    2016-04-01

    Xylitol, a value-added polyol deriving from D-xylose, is widely used in both the food and pharmaceutical industries. Despite extensive studies aiming to streamline the production of xylitol, the manufacturing cost of this product remains high while demand is constantly growing worldwide. Biotechnological production of xylitol from lignocellulosic waste may constitute an advantageous and sustainable option to address this issue. However, to date, there have been few reports of biomass conversion to xylitol. In the present study, xylitol was directly produced from rice straw hydrolysate using a recombinant Saccharomyces cerevisiae YPH499 strain expressing cytosolic xylose reductase (XR), along with β-glucosidase (BGL), xylosidase (XYL), and xylanase (XYN) enzymes (co-)displayed on the cell surface; xylitol production by this strain did not require addition of any commercial enzymes. All of these enzymes contributed to the consolidated bioprocessing (CBP) of the lignocellulosic hydrolysate to xylitol to produce 5.8 g/L xylitol with 79.5 % of theoretical yield from xylose contained in the biomass. Furthermore, nanofiltration of the rice straw hydrolysate provided removal of fermentation inhibitors while simultaneously increasing sugar concentrations, facilitating high concentration xylitol production (37.9 g/L) in the CBP. This study is the first report (to our knowledge) of the combination of cell surface engineering approach and membrane separation technology for xylitol production, which could be extended to further industrial applications.

  5. A rapid method for detection of genetically modified organisms based on magnetic separation and surface-enhanced Raman scattering.

    Science.gov (United States)

    Guven, Burcu; Boyacı, İsmail Hakkı; Tamer, Ugur; Çalık, Pınar

    2012-01-07

    In this study, a new method combining magnetic separation (MS) and surface-enhanced Raman scattering (SERS) was developed to detect genetically modified organisms (GMOs). An oligonucleotide probe which is specific for 35 S DNA target was immobilized onto gold coated magnetic nanospheres to form oligonucleotide-coated nanoparticles. A self assembled monolayer was formed on gold nanorods using 5,5'-dithiobis (2-nitrobenzoic acid) (DTNB) and the second probe of the 35 S DNA target was immobilized on the activated nanorod surfaces. Probes on the nanoparticles were hybridized with the target oligonucleotide. Optimization parameters for hybridization were investigated by high performance liquid chromatography. Optimum hybridization parameters were determined as: 4 μM probe concentration, 20 min immobilization time, 30 min hybridization time, 55 °C hybridization temperature, 750 mM buffer salt concentration and pH: 7.4. Quantification of the target concentration was performed via SERS spectra of DTNB on the nanorods. The correlation between the target concentration and the SERS signal was found to be linear within the range of 25-100 nM. The analyses were performed with only one hybridization step in 40 min. Real sample analysis was conducted using Bt-176 maize sample. The results showed that the developed MS-SERS assay is capable of detecting GMOs in a rapid and selective manner. This journal is © The Royal Society of Chemistry 2012

  6. Comparative Study on Assimilating Remote Sensing High Frequency Radar Surface Currents at an Atlantic Marine Renewable Energy Test Site

    Directory of Open Access Journals (Sweden)

    Lei Ren

    2017-12-01

    Full Text Available A variety of data assimilation approaches have been applied to enhance modelling capability and accuracy using observations from different sources. The algorithms have varying degrees of complexity of implementation, and they improve model results with varying degrees of success. Very little work has been carried out on comparing the implementation of different data assimilation algorithms using High Frequency radar (HFR data into models of complex inshore waters strongly influenced by both tides and wind dynamics, such as Galway Bay. This research entailed implementing four different data assimilation algorithms: Direct Insertion (DI, Optimal Interpolation (OI, Nudging and indirect data assimilation via correcting model forcing into a three-dimensional hydrodynamic model and carrying out detailed comparisons of model performances. This work will allow researchers to directly compare four of the most common data assimilation algorithms being used in operational coastal hydrodynamics. The suitability of practical data assimilation algorithms for hindcasting and forecasting in shallow coastal waters subjected to alternate wetting and drying using data collected from radars was assessed. Results indicated that a forecasting system of surface currents based on the three-dimensional model EFDC (Environmental Fluid Dynamics Code and the HFR data using a Nudging or DI algorithm was considered the most appropriate for Galway Bay. The largest averaged Data Assimilation Skill Score (DASS over the ≥6 h forecasting period from the best model NDA attained 26% and 31% for east–west and north–south surface velocity components respectively. Because of its ease of implementation and its accuracy, this data assimilation system can provide timely and useful information for various practical coastal hindcast and forecast operations.

  7. Optimization of the Nonaqueous Capillary Electrophoresis Separation of Metal Ions Using Mixture Design and Response Surface Methods

    OpenAIRE

    DEMİR, Cevdet; YÜCEL, Yasin

    2014-01-01

    Mixture experimental design was used to enhance the separation selectivity of metal ions in nonaqueous capillary electrophoresis. The separation of cations (Ag, Fe, Cr, Mn, Cd, Co, Pb, Ni, Zn and Cu) was achieved using imidazole as UV co-ion for indirect detection. Acetic acid was chosen as an electrolyte because its cathodic electroosmotic flow permits faster separation. The composition of organic solvents is important to achieve the best separation of all metal ions. Simplex latt...

  8. Some regularities of separate and simultaneous radiation polymerization of vinyl acetate and acrylonitrile in adsorption layer on aerosil surface

    International Nuclear Information System (INIS)

    Mund, S.L.; Bruk, M.A.; Abkin, A.D.

    1976-01-01

    The kinetics has been studied of initial stage radiation copolymerization and separate radiation polymerization of aerosil adsorbed vinylacetate (VA) and acrylonitrile (AN). The monomers were irradiated using a Co 60 gamma source or a RUP-400 X-ray unit. Infrared spectroscopy, nuclear magnetic resonance and gravimetry were used in the study. It has been found that in the dose rate interval studied (over 60-450 rad./sec) the break of kinetic chains during the polymerization of VA and its mixtures with AN is due to the reaction of degenerate transfer of the chains to the surface hydroxyl groups. When AN is polymerized, biomolecular break of chains prevails. The effective activation energy of polymerization is 1.5 kcal/mol for VA and 2.5 kcal/mol for AN. The order of polymerization rates by the concentration of adsorbed monomers at 50 deg, as well as by the irradiation dose rate is equal to 1 and 1 for VA and 3/2 and 0.7 for AN, respectively. The calculated values of copolymerization constants coincide with those characteristic of their radical polymerization in liquid phase. Isotherms for adsorption of VA and AN on aerosil at 30, 50 and 70 deg have been studied [ru

  9. Chromatographic Separation and Visual Detection on Wicking Microfluidic Devices: Quantitation of Cu2+ in Surface, Ground, and Drinking Water.

    Science.gov (United States)

    Bandara, Gayan C; Heist, Christopher A; Remcho, Vincent T

    2018-02-20

    Copper is widely applied in industrial and technological applications and is an essential micronutrient for humans and animals. However, exposure to high environmental levels of copper, especially through drinking water, can lead to copper toxicity, resulting in severe acute and chronic health effects. Therefore, regular monitoring of aqueous copper ions has become necessary as recent anthropogenic activities have led to elevated environmental concentrations of copper. On-site monitoring processes require an inexpensive, simple, and portable analytical approach capable of generating reliable qualitative and quantitative data efficiently. Membrane-based lateral flow microfluidic devices are ideal candidates as they facilitate rapid, inexpensive, and portable measurements. Here we present a simple, chromatographic separation approach in combination with a visual detection method for Cu 2+ quantitation, performed in a lateral flow microfluidic channel. This method appreciably minimizes interferences by incorporating a nonspecific polymer inclusion membrane (PIM) based assay with a "dot-counting" approach to quantification. In this study, hydrophobic polycaprolactone (PCL)-filled glass microfiber (GMF) membranes were used as the base substrate onto which the PIM was evenly dispensed as an array of dots. The devices thus prepared were then selectively exposed to oxygen radicals through a mask to generate a hydrophilic surface path along which the sample was wicked. Using this approach, copper concentrations from 1 to 20 ppm were quantified from 5 μL samples using only visual observation of the assay device.

  10. Effect of Reynolds Number and Periodic Unsteady Wake Flow Condition on Boundary Layer Development, Separation, and Intermittency Behavior Along the Suction Surface of a Low Pressure Turbine Blade

    Science.gov (United States)

    Schobeiri, M. T.; Ozturk, B.; Ashpis, David E.

    2007-01-01

    The paper experimentally studies the effects of periodic unsteady wake flow and different Reynolds numbers on boundary layer development, separation and re-attachment along the suction surface of a low pressure turbine blade. The experimental investigations were performed on a large scale, subsonic unsteady turbine cascade research facility at Turbomachinery Performance and Flow Research Laboratory (TPFL) of Texas A&M University. The experiments were carried out at Reynolds numbers of 110,000 and 150,000 (based on suction surface length and exit velocity). One steady and two different unsteady inlet flow conditions with the corresponding passing frequencies, wake velocities, and turbulence intensities were investigated. The reduced frequencies chosen cover the operating range of LP turbines. In addition to the unsteady boundary layer measurements, surface pressure measurements were performed. The inception, onset, and the extent of the separation bubble information collected from the pressure measurements were compared with the hot wire measurements. The results presented in ensemble-averaged, and the contour plot forms help to understand the physics of the separation phenomenon under periodic unsteady wake flow and different Reynolds number. It was found that the suction surface displayed a strong separation bubble for these three different reduced frequencies. For each condition, the locations defining the separation bubble were determined carefully analyzing and examining the pressure and mean velocity profile data. The location of the boundary layer separation was dependent of the Reynolds number. It is observed that starting point of the separation bubble and the re-attachment point move further downstream by increasing Reynolds number from 110,000 to 150,000. Also, the size of the separation bubble is smaller when compared to that for Re=110,000.

  11. Separation system

    International Nuclear Information System (INIS)

    Rubin, L.S.

    1986-01-01

    A disposal container is described for use in disposal of radioactive waste materials consisting of: top wall structure, bottom wall structure, and circumferential side wall structure interconnecting the top and bottom wall structures to define an enclosed container, separation structure in the container adjacent the inner surface of the side wall structure for allowing passage of liquid and retention of solids, inlet port structure in the top wall structure, discharge port structure at the periphery of the container in communication with the outer surface of the separation structure for receiving liquid that passes through the separation structure, first centrifugally actuated valve structure having a normal position closing the inlet port structure and a centrifugally actuated position opening the inlet port structure, second centrifugally actuated valve structure having a normal position closing the discharge port structure and a centrifugally actuated position opening the discharge port structure, and coupling structure integral with wall structure of the container for releasable engagement with centrifugal drive structure

  12. Shear waves in near surface 3D media-SH-wavefield separation, refraction time migration and tomography

    Science.gov (United States)

    Woelz, Susanne; Rabbel, Wolfgang; Mueller, Christof

    2009-05-01

    When investigating topographically irregular layers in the near surface with shear waves, it is of particular importance to consider the 3D-nature of wave propagation. Depending on the layer geometry and on the spatial arrangement of source- and receiver-points significant lateral ray bending can occur causing side-swipe traveltime effects and complicated polarisation patterns. As an example we present a study where 3D-shear wave refraction measurements were applied in order to reconstruct the geometry of a silted ancient harbour basin at the archaeological site of Miletus (West Turkey). Seismic signals were generated with a three-component vector force and recorded with three-component geophones arranged in 2D-arrays of 1 m grid spacing. Since a correct identification of refracted S-wave arrivals is a precondition to traveltime interpretation we investigated a method to decompose these wavefields with respect to their polarisation and azimuth of propagation. Taking advantage of the 2D-geophone arrangement we applied the following processing approach: In case of general lateral heterogeneity a decomposition can be performed by applying the curl and divergence operations to the vector wavefields recorded in 2D-arrays. The separated tangential and normal components to the wavefront in a plane are finally enhanced by combining the different force components in order to eliminate the radiation characteristics of the source. The decomposed wavefield was then the basis for 3D-refractor imaging through a newly formulated map migration of the refracted traveltime field. This technique was developed to map coherent basement structure on the meter-scale. Supplemental tomographic inversion using the refractor topography model as input provided a plausible velocity model, exhibiting characteristic anomalies such as a prominent low velocity zone overlain by a high velocity layer in the refractor. The seismic velocity structure suggests that the harbour basin was locally filled

  13. Combined Pressure, Temperature Contrast and Surface-Enhanced Separation of Carbon Dioxide for Post-Combustion Carbon Capture

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Zhen [Rice Univ., Houston, TX (United States); Wong, Michael [Rice Univ., Houston, TX (United States); Gupta, Mayank [Rice Univ., Houston, TX (United States); Hirasaki, George [Rice Univ., Houston, TX (United States); Cox, Kenneth [Rice Univ., Houston, TX (United States)

    2016-05-01

    The Rice University research team developed a hybrid carbon dioxide (CO2) absorption process combining absorber and stripper columns using a high surface area ceramic foam gas-liquid contactor for enhanced mass transfer and utilizing waste heat for regeneration. This integrated absorber/desorber arrangement will reduce space requirements, an important factor for retrofitting existing coal-fired power plants with CO2 capture technology. Described in this report, we performed an initial analysis to estimate the technical and economic feasibility of the process. A one-dimensional (1D) CO2 absorption column was fabricated to measure the hydrodynamic and mass transfer characteristics of the ceramic foam. A bench-scale prototype was constructed to implement the complete CO2 separation process and tested to study various aspects of fluid flow in the process. A model was developed to simulate the two-dimensional (2D) fluid flow and optimize the CO2 capture process. Test results were used to develop a final technoeconomic analysis and identify the most appropriate absorbent as well as optimum operating conditions to minimize capital and operating costs. Finally, a technoeconomic study was performed to assess the feasibility of integrating the process into a 600 megawatt electric (MWe) coal-fired power plant. With process optimization, $82/MWh of COE can be achieved using our integrated absorber/desorber CO2 capture technology, which is very close to DOE's target that no more than a 35% increase in COE with CCS. An environmental, health, and safety (EH&S) assessment of the capture process indicated no significant concern in terms of EH&S effects or legislative compliance.

  14. The renewable alternative

    International Nuclear Information System (INIS)

    Anon.

    1992-01-01

    This chapter discusses renewable energy sources as an alternative to a fossil fuel based economy. The topics discussed in the chapter include the historic aspects and current status of use of renewable energy, status of the renewable energy industry, market barriers to renewable energy, research and development and commercialization of renewable energy, the environmental and social costs associated with renewable energy, valuing future costs and benefits of energy use, and the potential market of renewable energy

  15. Hybrid selective surface hydrophilization and froth flotation separation of hazardous chlorinated plastics from E-waste with novel nanoscale metallic calcium composite

    Energy Technology Data Exchange (ETDEWEB)

    Mallampati, Srinivasa Reddy, E-mail: srireddys@ulsan.ac.kr; Heo, Je Haeng; Park, Min Hee

    2016-04-05

    Highlights: • Nanometallic Ca/CaO treatment significantly enhanced PVC surface hydrophilicity. • The contact angle of PVC significantly decreased compared to other E-waste plastics. • 100% of PVC was selectively separated with 96.4% purity from E-waste plastics. • SEM/XPS results indicated an oxidative degradation of chlorides on the PVC surface. • Hybrid treatment with nanometallic Ca/CaO and froth flotation is effective. - Abstract: Treatment by a nanometallic Ca/CaO composite has been found to selectively hydrophilize the surface of polyvinyl chloride (PVC), enhancing its wettability and thereby promoting its separation from E-waste plastics by means of froth flotation. The treatment considerably decreased the water contact angle of PVC, by about 18°. The SEM images of the PVC plastic after treatment displayed significant changes in their surface morphology compared to other plastics. The SEM-EDS results reveal that a markedly decrease of [Cl] concentration simultaneously with dramatic increase of [O] on the surface of the PCV samples. XPS results further confirmed an increase of hydrophilic functional groups on the PVC surface. Froth flotation at 100 rpm mixing speed was found to be optimal, separating 100% of the PVC into a settled fraction of 96.4% purity even when the plastics fed into the reactor were of nonuniform size and shape. The total recovery of PVC-free plastics in E-waste reached nearly 100% in the floated fraction, significantly improved from the 20.5 wt% of light plastics that can be recovered by means of conventional wet gravity separation. The hybrid method of nanometallic Ca/CaO treatment and froth flotation is effective in the separation of hazardous chlorinated plastics from E-waste plastics.

  16. Hybrid selective surface hydrophilization and froth flotation separation of hazardous chlorinated plastics from E-waste with novel nanoscale metallic calcium composite

    International Nuclear Information System (INIS)

    Mallampati, Srinivasa Reddy; Heo, Je Haeng; Park, Min Hee

    2016-01-01

    Highlights: • Nanometallic Ca/CaO treatment significantly enhanced PVC surface hydrophilicity. • The contact angle of PVC significantly decreased compared to other E-waste plastics. • 100% of PVC was selectively separated with 96.4% purity from E-waste plastics. • SEM/XPS results indicated an oxidative degradation of chlorides on the PVC surface. • Hybrid treatment with nanometallic Ca/CaO and froth flotation is effective. - Abstract: Treatment by a nanometallic Ca/CaO composite has been found to selectively hydrophilize the surface of polyvinyl chloride (PVC), enhancing its wettability and thereby promoting its separation from E-waste plastics by means of froth flotation. The treatment considerably decreased the water contact angle of PVC, by about 18°. The SEM images of the PVC plastic after treatment displayed significant changes in their surface morphology compared to other plastics. The SEM-EDS results reveal that a markedly decrease of [Cl] concentration simultaneously with dramatic increase of [O] on the surface of the PCV samples. XPS results further confirmed an increase of hydrophilic functional groups on the PVC surface. Froth flotation at 100 rpm mixing speed was found to be optimal, separating 100% of the PVC into a settled fraction of 96.4% purity even when the plastics fed into the reactor were of nonuniform size and shape. The total recovery of PVC-free plastics in E-waste reached nearly 100% in the floated fraction, significantly improved from the 20.5 wt% of light plastics that can be recovered by means of conventional wet gravity separation. The hybrid method of nanometallic Ca/CaO treatment and froth flotation is effective in the separation of hazardous chlorinated plastics from E-waste plastics.

  17. Surface directed phase separation of semiconductor ferroelectric polymer blends and their use in non-volatile memories

    NARCIS (Netherlands)

    Breemen, A.J.J.M. van; Zaba, T.; Khikhlovskyi, V.; Michels, J.; Janssen, R.; Kemerink, M.; Gelinck, G.

    2015-01-01

    The polymer phase separation of P(VDF-TrFE):F8BT blends is studied in detail. Its morphology is key to the operation and performance of memory diodes. In this study, it is demonstrated that it is possible to direct the semiconducting domains of a phase-separating mixture of P(VDF-TrFE) and F8BT in a

  18. Hybrid selective surface hydrophilization and froth flotation separation of hazardous chlorinated plastics from E-waste with novel nanoscale metallic calcium composite.

    Science.gov (United States)

    Mallampati, Srinivasa Reddy; Heo, Je Haeng; Park, Min Hee

    2016-04-05

    Treatment by a nanometallic Ca/CaO composite has been found to selectively hydrophilize the surface of polyvinyl chloride (PVC), enhancing its wettability and thereby promoting its separation from E-waste plastics by means of froth flotation. The treatment considerably decreased the water contact angle of PVC, by about 18°. The SEM images of the PVC plastic after treatment displayed significant changes in their surface morphology compared to other plastics. The SEM-EDS results reveal that a markedly decrease of [Cl] concentration simultaneously with dramatic increase of [O] on the surface of the PCV samples. XPS results further confirmed an increase of hydrophilic functional groups on the PVC surface. Froth flotation at 100rpm mixing speed was found to be optimal, separating 100% of the PVC into a settled fraction of 96.4% purity even when the plastics fed into the reactor were of nonuniform size and shape. The total recovery of PVC-free plastics in E-waste reached nearly 100% in the floated fraction, significantly improved from the 20.5wt% of light plastics that can be recovered by means of conventional wet gravity separation. The hybrid method of nanometallic Ca/CaO treatment and froth flotation is effective in the separation of hazardous chlorinated plastics from E-waste plastics. Copyright © 2015 Elsevier B.V. All rights reserved.

  19. Microstructural study by XPS and GISAXS of surface layers formed via phase separation and percolation in polystyren/tetrabutyl titanate/alumina composite films

    International Nuclear Information System (INIS)

    Zeng Yanwei; Tian Changan; Liu Junliang

    2006-01-01

    The XPS and GISAXS have been employed as useful tools to probe the chemical compositional and microstructural evolutions in the surface layers formed via phase separation and percolation in polystyren/Ti(OBut) 4 /alumina composite thick films. The surface enrichment of Ti species due to the migration of Ti(OBut) 4 molecules in the films was found to show an incubation period of ∼15 h while the samples were treated at 100 deg. C before a remarkable progress can be identified. According to the XPS and GISAXS data, Key mechanism to govern this surface process is phenomenologically considered to be the specific phase separation behavior in Ti(OBut) 4 /PS blend and the subsequent percolating process. The extended thermal treatment was found to make the surface layer microstructure evolve from local phase separation featured with an increasing population of individual microbeads of Ti(OBut) 4 (∼1.5 nm in radius) to the formation of large size clusters of microbeads due to their interconnections, accompanied by the growth of every microbead itself to ∼10 nm on the average, which provokes and then enhances the surface enrichment of Ti(OBut) 4 since these clusters act as a fast diffusion network due to percolation effect

  20. Renewable Energy Country Profiles. Pacific

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2012-09-15

    The IRENA Renewable Energy Country Profiles take stock of the latest development of renewable energy in two regions where renewable energy can make a significant contribution to combat climate change and bring modern energy services to everyone: Africa and the Pacific. These two regions are presented separately in this volume and its sister publication. The country profiles combine elements of IRENA analysis with the latest information available from a vast array of sources in order to give a brief yet comprehensive and up-to-date picture of the situation of renewable energy that includes energy supply, electrical capacity, energy access, policies, targets, investment climate, projects and endowment in renewable energy resources. Because of the different timelines of these sources, data presented here refer to years between 2008 and 2012. Data availability also differs from country to country, which makes comparison with a wider regional group possible only for the year for which figures are available for all the members of the group; while this may not be the most recent year, the differences between countries, regions and the world remain striking. The current country profiles are just a starting point; they will be extended upon with new indicators to make them more informative, and maintained as a live product on the IRENA website as a key source of information on renewable energy.

  1. Renewable Energy Country Profiles. Africa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2012-02-15

    The IRENA Renewable Energy Country Profiles take stock of the latest development of renewable energy in two regions where renewable energy can make a significant contribution to combat climate change and bring modern energy services to everyone: Africa and the Pacific. These two regions are presented separately in this volume and its sister publication. The country profiles combine elements of IRENA analysis with the latest information available from a vast array of sources in order to give a brief yet comprehensive and up-to-date picture of the situation of renewable energy that includes energy supply, electrical capacity, energy access, policies, targets, investment climate, projects and endowment in renewable energy resources. Because of the different timelines of these sources, data presented here refer to years between 2008 and 2012. Data availability also differs from country to country, which makes comparison with a wider regional group possible only for the year for which figures are available for all the members of the group; while this may not be the most recent year, the differences between countries, regions and the world remain striking. The current country profiles are just a starting point; they will be extended upon with new indicators to make them more informative, and maintained as a live product on the IRENA website as a key source of information on renewable energy.

  2. Immobilization of Styrene-acrylamide Co-polymer on Either Silica Particles or Inner Surface of Silica Capillary for the Separation of D-Glucose Anomers

    International Nuclear Information System (INIS)

    Ali, Faiz; Kim, Yune Sung; Cheong, Won Jo

    2014-01-01

    Styrene-acrylamide co-polymer was immobilized on porous partially sub-2 μm silica monolith particles and inner surface of fused silica capillary (50 μm ID and 28 cm length) to result in μLC and CEC stationary phases, respectively, for separation of anomeric D-glucose derivatives. Reversed addition-fragmentation transfer (RAFT) polymerization was incorporated to induce surface polymerization. Acrylamide was employed to incorporate amide-functionality in the stationary phase. The resultant μLC and CEC stationary phases were able to separate isomers of D-glucose derivatives with high selectivity and efficiency. The mobile phase of 75/ 25 (v/v) acetonitrile (ACN)/water with 0.1% TFA, was used for HPLC with a packed column (1 mm ID, 300 mm length). The effects of pH and ACN composition on anomeric separation of D-glucose in CEC have been examined. A mobile phase of 85/15 (v/v) ACN/30 mM sodium acetate pH 6.7 was found the optimized mobile phase for CEC. The CEC stationary phase also gave good separation of other saccharides such as maltotriose and Dextran 1500 (MW∼1500) with good separation efficiency (number of theoretical plates ∼300,000/m)

  3. Immobilization of Styrene-acrylamide Co-polymer on Either Silica Particles or Inner Surface of Silica Capillary for the Separation of D-Glucose Anomers

    Energy Technology Data Exchange (ETDEWEB)

    Ali, Faiz; Kim, Yune Sung; Cheong, Won Jo [Inha Univ., Incheon (Korea, Republic of)

    2014-02-15

    Styrene-acrylamide co-polymer was immobilized on porous partially sub-2 μm silica monolith particles and inner surface of fused silica capillary (50 μm ID and 28 cm length) to result in μLC and CEC stationary phases, respectively, for separation of anomeric D-glucose derivatives. Reversed addition-fragmentation transfer (RAFT) polymerization was incorporated to induce surface polymerization. Acrylamide was employed to incorporate amide-functionality in the stationary phase. The resultant μLC and CEC stationary phases were able to separate isomers of D-glucose derivatives with high selectivity and efficiency. The mobile phase of 75/ 25 (v/v) acetonitrile (ACN)/water with 0.1% TFA, was used for HPLC with a packed column (1 mm ID, 300 mm length). The effects of pH and ACN composition on anomeric separation of D-glucose in CEC have been examined. A mobile phase of 85/15 (v/v) ACN/30 mM sodium acetate pH 6.7 was found the optimized mobile phase for CEC. The CEC stationary phase also gave good separation of other saccharides such as maltotriose and Dextran 1500 (MW∼1500) with good separation efficiency (number of theoretical plates ∼300,000/m)

  4. Spatiotemporal Co-variability of Surface Climate for Renewable Energy across the Contiguous United States: Role of the North Atlantic Subtropical High

    Science.gov (United States)

    Doering, K.; Steinschneider, S.

    2017-12-01

    The variability of renewable energy supply and drivers of demand across space and time largely determines the energy balance within power systems with a high penetration of renewable technologies. This study examines the joint spatiotemporal variability of summertime climate linked to renewable energy production (precipitation, wind speeds, insolation) and energy demand (temperature) across the contiguous United States (CONUS) between 1948 and 2015. Canonical correlation analysis is used to identify the major modes of joint variability between summer wind speeds and precipitation and related patterns of insolation and temperature. Canonical variates are then related to circulation anomalies to identify common drivers of the joint modes of climate variability. Results show that the first two modes of joint variability between summer wind speeds and precipitation exhibit pan-US dipole patterns with centers of action located in the eastern and central CONUS. Temperature and insolation also exhibit related US-wide dipoles. The relationship between canonical variates and lower-tropospheric geopotential height indicates that these modes are related to variability in the North Atlantic subtropical high (NASH). This insight can inform optimal strategies for siting renewables in an interconnected electric grid, and has implications for the impacts of climate variability and change on renewable energy systems.

  5. Semi-automated technique for the separation and determination of barium and strontium in surface waters by ion exchange chromatography and atomic emission spectrometry

    International Nuclear Information System (INIS)

    Pierce, F.D.; Brown, H.R.

    1977-01-01

    A semi-automated method for the separation and the analysis of barium and strontium in surface waters by atomic emission spectrometry is described. The method employs a semi-automated separation technique using ion exchange and an automated aspiration-analysis procedure. Forty specimens can be prepared in approximately 90 min and can be analyzed for barium and strontium content in 20 min. The detection limits and sensitivities provided by the described technique are 0.003 mg/l and 0.01 mg/l respectively for barium and 0.00045 mg/l and 0.003 mg/l respectively for strontium

  6. Renewing governance.

    Science.gov (United States)

    Loos, Gregory P

    2003-01-01

    Globalization's profound influence on social and political institutions need not be negative. Critics of globalization have often referred to the "Impossible Trinity" because decision-making must 1. respect national sovereignty, 2. develop and implement firm regulation, and 3. allow capital markets to be as free as possible. To many, such goals are mutually exclusive because history conditions us to view policy-making and governance in traditional molds. Thus, transnational governance merely appears impossible because current forms of governance were not designed to provide it. The world needs new tools for governing, and its citizens must seize the opportunity to help develop them. The rise of a global society requires a greater level of generality and inclusion than is found in most policy bodies today. Politicians need to re-examine key assumptions about government. States must develop ways to discharge their regulatory responsibilities across borders and collaborate with neighboring jurisdictions, multilateral bodies, and business. Concepts such as multilateralism and tripartism show great promise. Governments must engage civil society in the spirit of shared responsibility and democratic decision-making. Such changes will result in a renewal of the state's purpose and better use of international resources and expertise in governance.

  7. Enhanced the performance of graphene oxide/polyimide hybrid membrane for CO2 separation by surface modification of graphene oxide using polyethylene glycol

    Science.gov (United States)

    Wu, Li-guang; Yang, Cai-hong; Wang, Ting; Zhang, Xue-yang

    2018-05-01

    Polyethylene glycol (PEG) with different molecular weights was first used to modify graphene oxide (GO) samples. Subsequently, polyimide (PI) hybrid membranes containing modified-GO were fabricated via in situ polymerization. The separation performance of these hybrid membranes was evaluated using permeation experiments for CO2 and N2 gases. The morphology characterization showed that PEG with suitable molecular weight could be successfully grafted on the GO surface. PEG modification altered the surface properties of GO and introduced defective structures onto GO surface. This caused strong surface polarity and high free volume of membranes containing PEG-modified GO, thereby improving the separation performance of membranes. The addition of PEG-GO with low molecular weight effectively increased gas diffusion through hybrid membranes. The hybrid membranes containing PEG-GO with large molecular weight had high solubility performance for CO2 gas due to the introduction of numerous polar groups into polymeric membranes. With the loading content of modified GO, the CO2 gas permeability of hybrid membranes initially increased but eventually decreased. The optimal content of modified GO in membranes reached 3.0 wt%. When too much PEG added (exceeding 30 g), some impurities formed on GO surface and some aggregates appeared in the resulting hybrid membrane, which depressed the membrane performance.

  8. Continuously renewed wall for a thermonuclear reactor

    International Nuclear Information System (INIS)

    Livshits, A.I.; Pustovojt, YU.M.; Samartsev, A.A.; Gosudarstvennyj Komitet po Ispol'zovaniyu Atomnoj Ehnergii SSSR, Moscow. Inst. Atomnoj Ehnergii)

    1982-01-01

    The possibility of creating a continuously renewed first wall of a thermonuclear reactor is experimentally investigated. The following variants of the wall are considered: the wall is double, its part turned to plasma is made of comparatively thin material. The external part separated from it by a small gap appears to be protected from interaction with plasma and performs structural functions. The gap contains the mixture of light helium and hydrogen and carbon-containing gas. The light gas transfers heat from internal part of the wall to the external part. Carbon-containing gas provides continuous renewal of carbon coating of the operating surface. The experiment is performed with palladium membrane 20 μm thick. Carbon is introduced into the membrane by benzol pyrolysis on one of the surfaces at the membrane temperature of 900 K. Carbon removal from the operating side of the wall due to its spraying by fast particles is modelled by chemical itching with oxygen given to the operating membrane wall. Observation of the carbon release on the operating surface is performed mass-spectrometrically according to the observation over O 2 transformation into CO and CO 2 . It is shown that in cases of benzol pressure of 5x10 -7 torr, carbon current on the opposite surface is not less than 3x10 12 atoms/sm 2 s and corresponds to the expected wall spraying rate in CF thermonuclear reactors. It is also shown that under definite conditions the formation and maintaining of a through protective carbon coating in the form of a monolayer or volumetric phase is possible

  9. Flotation separation of PET from a PET, PVC and PS mixture by the hydrofilization of the PET surface in NaOH solutions

    Directory of Open Access Journals (Sweden)

    Ľubica Kozáková

    2005-11-01

    Full Text Available Recycling is the most effective method of waste minimization created by the human activity. The idea of waste re-use as a result of environmental, social and economical factors is becoming very relevant in the last decades. The portion of plastics in the municipal waste is growing year by year as also is its use in the wrapping industry. A condition for recycling technologies is the input of highly pure plastics (without undesirable admixtures suitable for recycling. Various separation technologies can be used which provide separation of particular components of plastic waste and contaminants. Flotation is one of the separation methods used especially for the ore beneficiation but recently is widely also used for the separation of various types of waste. Plastics, which are not possible to be separated by gravitational methods (because they have almost the same density, PET from beverage bottles, PVC from bottles and foils and PS from beverage beakers, were studied. By changing the surface properties of PET from naturally hydrophobic to hydrophilic by the adjustment in a NaOH solution, PET with the recovery of up to 99 % in the non-foamy product and with the product purity of up to 98 % was acquired by the flotation.

  10. Applying a method of chemical separation and mass spectrometry for the determination of radium-226 in surface water

    International Nuclear Information System (INIS)

    Sibello Hernandez, Rita Y; Cozzella, Maria Letizia; Guillen Arruebarrena, Aniel

    2014-01-01

    Radium-226 ( 226 Ra) is a naturally occurring radionuclide, alpha emitter with half-life of 1 622 years originating from uranium-238 ( 238 U). Its presence in drinking water is a major radiological hazards, which requires constant monitoring. The analytical techniques used in the determination of 226 Ra generally require the establishment of secular equilibrium and/or tedious separation of other elements. The main objective of this paper is to demonstrate the efficiency and speed of a method of preconcentration and separation of 226 Ra in natural water samples using coprecipitation with MnO 2 radius and purification by cation exchange resin Dowex 50WX8. Measurement technique was Quadrupole Mass Spectrometry and associated induced plasma ICP-Q-MS. The 226 Ra values obtained are in the range of 0,010-0,219 pg/L in natural waters analyzed

  11. Wetting-layer formation mechanisms of surface-directed phase separation under different quench depths with off-critical compositions in polymer binary mixture

    Science.gov (United States)

    Yan, Li-Tang; Xie, Xu-Ming

    2007-02-01

    Focusing on the off-critical condition, the quench depth dependence of surface-directed phase separation in the polymer binary mixture is numerically investigated by combination of the Cahn-Hilliard-Cook theory and the Flory-Huggins-de Gennes theory. Two distinct situations, i.e., for the wetting, the minority component is preferred by the surface and the majority component is preferred by the surface, are discussed in detail. The simulated results show that the formation mechanism of the wetting layer is affected by both the quench depth and the off-critical extent. Moreover, a diagram, illustrating the formation mechanisms of the wetting layer with various quench depths and compositions, is obtained on the basis of the simulated results. It is found that, when the minority component is preferred by the surface, the growth of the wetting layer can exhibit pure diffusion limited growth law, logarithmic growth law, and Lifshitz-Slyozov growth law. However, when the majority component is preferred by the surface, the wetting layer always grows logarithmically, regardless of the quench depth and the off-critical extent. It is interesting that the surface-induced nucleation can be observed in this case. The simulated results demonstrate that the surface-induced nucleation only occurs below a certain value of the quench depth, and a detailed range about it is calculated and indicated. Furthermore, the formation mechanisms of the wetting layer are theoretically analyzed in depth by the chemical potential gradient.

  12. The effects of processing conditions on the surface morphology and hydrophobicity of polyvinylidene fluoride membranes prepared via vapor-induced phase separation

    Science.gov (United States)

    Peng, Yuelian; Fan, Hongwei; Ge, Ju; Wang, Shaobin; Chen, Ping; Jiang, Qi

    2012-12-01

    The present investigation reveals how the surface morphology and the hydrophobicity of polyvinylidene fluoride (PVDF) membranes, which were prepared via a vapor-induced phase separation method, were affected by the initial PVDF content in the casting solution and the air temperature. The surface morphology was characterized with scanning electron microscopy. A ternary phase diagram of PVDF/N, N-dimethylacetamide/water was constructed to explain the formation mechanism of the different morphologies. The results show that different membrane morphologies and hydrophobicities can be obtained by changing the processing conditions. Low air temperature and high PVDF contents facilitate the crystallization process, resulting in the formation of a porous skin and particle morphology, which increases the hydrophobicity of the surface. High air temperature and low PVDF contents are favorable for the formation of a net-like surface morphology via spinodal decomposition and lead to a superhydrophobic surface. Theoretical calculations were performed to testify that the net-like surface was more favorable for superhydrophobicity than the particle-based surface.

  13. Fusion fuel and renewables

    International Nuclear Information System (INIS)

    Entler, Slavomir

    2015-01-01

    It is shown that fusion fuel meets all aspects applied when defining renewables. A table of definitions of renewables is presented. The sections of the paper are as follows: An industrial renewable source; Nuclear fusion; Current situation in research; Definitions of renewable sources; Energy concept of nuclear fusion; Fusion fuel; Natural energy flow; Environmental impacts; Fusion fuel assessment; Sustainable power; and Energy mix from renewables. (P.A.)

  14. Response surface methodology for the determination of the design space of enantiomeric separations on cinchona-based zwitterionic chiral stationary phases by high performance liquid chromatography.

    Science.gov (United States)

    Hanafi, Rasha Sayed; Lämmerhofer, Michael

    2018-01-26

    Quality-by-Design approach for enantioselective HPLC method development surpasses Quality-by-Testing in offering the optimal separation conditions with the least number of experiments and in its ability to describe the method's Design Space visually which helps to determine enantiorecognition to a significant extent. Although some schemes exist for enantiomeric separations on Cinchona-based zwitterionic stationary phases, the exact design space and the weights by which each of the chromatographic parameters influences the separation have not yet been statistically studied. In the current work, a screening design followed by a Response Surface Methodology optimization design were adopted for enantioseparation optimization of 3 model drugs namely the acidic Fmoc leucine, the amphoteric tryptophan and the basic salbutamol. The screening design proved that the acid/base additives are of utmost importance for the 3 chiral drugs, and that among 3 different pairs of acids and bases, acetic acid and diethylamine is the couple able to provide acceptable resolution at variable conditions. Visualization of the response surface of the retention factor, separation factor and resolution helped describe accurately the magnitude by which each chromatographic factor (% MeOH, concentration and ratio of acid base modifiers) affects the separation while interacting with other parameters. The global optima compromising highest enantioresolution with the least run time for the 3 chiral model drugs varied extremely, where it was best to set low % methanol with equal ratio of acid-base modifiers for the acidic drug, very high % methanol and 10-fold higher concentration of the acid for the amphoteric drug while 20 folds of the base modifier with moderate %methanol were needed for the basic drug. Considering the selected drugs as models for many series of structurally related compounds, the design space defined and the optimum conditions computed are the key for method development on

  15. Gas separating

    Science.gov (United States)

    Gollan, A.

    1988-03-29

    Feed gas is directed tangentially along the non-skin surface of gas separation membrane modules comprising a cylindrical bundle of parallel contiguous hollow fibers supported to allow feed gas to flow from an inlet at one end of a cylindrical housing through the bores of the bundled fibers to an outlet at the other end while a component of the feed gas permeates through the fibers, each having the skin side on the outside, through a permeate outlet in the cylindrical casing. 3 figs.

  16. Vapor-Liquid Sol-Gel Approach to Fabricating Highly Durable and Robust Superhydrophobic Polydimethylsiloxane@Silica Surface on Polyester Textile for Oil-Water Separation.

    Science.gov (United States)

    Su, Xiaojing; Li, Hongqiang; Lai, Xuejun; Zhang, Lin; Wang, Jing; Liao, Xiaofeng; Zeng, Xingrong

    2017-08-23

    Large-scale fabrication of superhydrophobic surfaces with excellent durability by simple techniques has been of considerable interest for its urgent practical application in oil-water separation in recent years. Herein, we proposed a facile vapor-liquid sol-gel approach to fabricating highly durable and robust superhydrophobic polydimethylsiloxane@silica surfaces on the cross-structure polyester textiles. Scanning electron microscopy and Fourier transform infrared spectroscopy demonstrated that the silica generated from the hydrolysis-condensation of tetraethyl orthosilicate (TEOS) gradually aggregated at microscale driven by the extreme nonpolar dihydroxyl-terminated polydimethylsiloxane (PDMS(OH)). This led to construction of hierarchical roughness and micronano structures of the superhydrophobic textile surface. The as-fabricated superhydrophobic textile possessed outstanding durability in deionized water, various solvents, strong acid/base solutions, and boiling/ice water. Remarkably, the polyester textile still retained great water repellency and even after ultrasonic treatment for 18 h, 96 laundering cycles, and 600 abrasion cycles, exhibiting excellent mechanical robustness. Importantly, the superhydrophobic polyester textile was further applied for oil-water separation as absorption materials and/or filter pipes, presenting high separation efficiency and great reusability. Our method to construct superhydrophobic textiles is simple but highly efficient; no special equipment, chemicals, or atmosphere is required. Additionally, no fluorinated slianes and organic solvents are involved, which is very beneficial for environment safety and protection. Our findings conceivably stand out as a new tool to fabricate organic-inorganic superhydrophobic surfaces with strong durability and robustness for practical applications in oil spill accidents and industrial sewage emission.

  17. Synthesis of Silicalite Membrane with an Aluminum-Containing Surface for Controlled Modification of Zeolitic Pore Entries for Enhanced Gas Separation

    Directory of Open Access Journals (Sweden)

    Shaowei Yang

    2018-02-01

    Full Text Available The separation of small molecule gases by membrane technologies can help performance enhancement and process intensification for emerging advanced fossil energy systems with CO2 capture capacity. This paper reports the demonstration of controlled modification of zeolitic channel size for the MFI-type zeolite membranes to enhance the separation of small molecule gases such as O2 and N2. Pure-silica MFI-type zeolite membranes were synthesized on porous α-alumina disc substrates with and without an aluminum-containing thin skin on the outer surface of zeolite membrane. The membranes were subsequently modified by on-stream catalytic cracking deposition (CCD of molecular silica to reduce the effective openings of the zeolitic channels. Such a pore modification caused the transition of gas permeation from the N2-selective gaseous diffusion mechanism in the pristine membrane to the O2-selective activated diffusion mechanism in the modified membrane. The experimental results indicated that the pore modification could be effectively limited within the aluminum-containing surface of the MFI zeolite membrane to minimize the mass transport resistance for O2 permeation while maintaining its selectivity. The implications of pore modification on the size-exclusion-enabled gas selectivity were discussed based on the kinetic molecular theory. In light of the theoretical analysis, experimental investigation was performed to further enhance the membrane separation selectivity by chemical liquid deposition of silica into the undesirable intercrystalline spaces.

  18. Renewable energy annual 1996

    International Nuclear Information System (INIS)

    1997-03-01

    This report presents summary data on renewable energy consumption, the status of each of the primary renewable technologies, a profile of each of the associated industries, an analysis of topical issues related to renewable energy, and information on renewable energy projects worldwide. It is the second in a series of annual reports on renewable energy. The renewable energy resources included in the report are biomass (wood and ethanol); municipal solid waste, including waste-to-energy and landfill gas; geothermal; wind; and solar energy, including solar thermal and photovoltaic. The report also includes various appendices and a glossary

  19. Renewable energy annual 1996

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    This report presents summary data on renewable energy consumption, the status of each of the primary renewable technologies, a profile of each of the associated industries, an analysis of topical issues related to renewable energy, and information on renewable energy projects worldwide. It is the second in a series of annual reports on renewable energy. The renewable energy resources included in the report are biomass (wood and ethanol); municipal solid waste, including waste-to-energy and landfill gas; geothermal; wind; and solar energy, including solar thermal and photovoltaic. The report also includes various appendices and a glossary.

  20. Structure, morphology and cell affinity of poly(L-lactide) films surface-functionalized with chitosan nanofibers via a solid–liquid phase separation technique

    Energy Technology Data Exchange (ETDEWEB)

    Zhao, Jianhao, E-mail: jhzhao@jnu.edu.cn [Department of Materials Science and Engineering, College of Science and Engineering, Jinan University, Guangzhou 510632 (China); Engineering Research Center of Artificial Organs and Materials, Ministry of Education, Guangzhou 510632 (China); Han, Wanqing; Tang, Minjian [Department of Materials Science and Engineering, College of Science and Engineering, Jinan University, Guangzhou 510632 (China); Tu, Mei; Zeng, Rong [Department of Materials Science and Engineering, College of Science and Engineering, Jinan University, Guangzhou 510632 (China); Engineering Research Center of Artificial Organs and Materials, Ministry of Education, Guangzhou 510632 (China); Liang, Zhihong [Analytical and Testing Center, Jinan University, Guangzhou 510632 (China); Zhou, Changren [Department of Materials Science and Engineering, College of Science and Engineering, Jinan University, Guangzhou 510632 (China); Engineering Research Center of Artificial Organs and Materials, Ministry of Education, Guangzhou 510632 (China)

    2013-04-01

    Poly(L-lactide) films with a nano-structured surface by immobilizing chitosan nanofibers (CSNFs) for improving the cell affinity were fabricated via a solid-liquid phase separation technique. The successful grafting of CSNFs on the surface of poly(L-lactide) films was confirmed by the binding energy of N1s at 398.0 eV in the X-ray photoelectron spectroscopy and the amide I and II bands of chitosan at 1650 and 1568 cm{sup −1} in the Fourier transform infrared spectroscopy. Compared with the poly(L-lactide) film, the hydrophilicity was improved with a lower water contact angle of 83.3 ± 1.9° and 75.3 ± 2.5° for the CSNFs-grafted and CSNFs-grafted/anchored poly(L-lactide) films respectively. The scanning electron microscopy and atomic force microscopy analyses showed that the grafted CSNFs with 50–500 nm in diameter were randomly arranged on the film surface and entangled with the anchored CSNFs on the outermost layer. The 3T3 fibroblasts culture indicated cells tended to attach and stretch along the CSNFs on the film surface. The cell viability measurement revealed that among all the samples, the film with both grafted and anchored CSNFs exhibited the highest cell proliferation rate that was twice as much of the poly(L-lactide) film at 7 d. Herein, engineering a nano-structured surface by solid–liquid phase separation will be a promising tool for surface modification of biomaterials. Highlights: ► A surface nano-structured poly(L-lactide) film with chitosan nanofibers was prepared. ► Grafted and anchored chitosan nanofibers were obtained by different treatment ways. ► Hydrophilicity was improved by immobilizing chitosan nanofibers on the film surface. ► Cell viability was enhanced on modified poly(L-lactide) film with chitosan nanofibers. ► Cells tended to attach and stretch along chitosan nanofibers on the film surface.

  1. Impacts of land surface properties and atmospheric CO2 on the Last Glacial Maximum climate: a factor separation analysis

    Directory of Open Access Journals (Sweden)

    G. Munhoven

    2009-06-01

    Full Text Available Many sensitivity studies have been carried out, using climate models of different degrees of complexity to test the climate response to Last Glacial Maximum boundary conditions. Here, instead of adding the forcings successively as in most previous studies, we applied the separation method of U. Stein et P. Alpert 1993, in order to determine rigorously the different contributions of the boundary condition modifications, and isolate the pure contributions from the interactions among the forcings. We carried out a series of sensitivity experiments with the model of intermediate complexity Planet Simulator, investigating the contributions of the ice sheet expansion and elevation, the lowering of the atmospheric CO2 and of the vegetation cover change on the LGM climate. The separation of the ice cover and orographic contributions shows that the ice albedo effect is the main contributor to the cooling of the Northern Hemisphere, whereas orography has only a local cooling impact over the ice sheets. The expansion of ice cover in the Northern Hemisphere causes a disruption of the tropical precipitation, and a southward shift of the ITCZ. The orographic forcing mainly contributes to the disruption of the atmospheric circulation in the Northern Hemisphere, leading to a redistribution of the precipitation, but weakly impacts the tropics. The isolated vegetation contribution also induces strong cooling over the continents of the Northern Hemisphere that further affects the tropical precipitation and reinforce the southward shift of the ITCZ, when combined with the ice forcing. The combinations of the forcings generate many non-linear interactions that reinforce or weaken the pure contributions, depending on the climatic mechanism involved, but they are generally weaker than the pure contributions. Finally, the comparison between the LGM simulated climate and climatic reconstructions over Eurasia suggests that our results reproduce well the south-west to

  2. Renewable Energy Certificates (RECs)

    Science.gov (United States)

    Renewable Energy Certificates (RECs), are tradable, non-tangible energy commodities in the United States that represent proof that 1 megawatt-hour (MWh) of electricity was generated from an eligible renewable energy resource.

  3. Online driver's license renewal.

    Science.gov (United States)

    2015-09-01

    The Kentucky Department of Vehicle Regulation is exploring the possibility of developing and implementing online : drivers license renewal. The objective of this project was to: 1) evaluate online drivers license and REAL ID renewal : programs ...

  4. Resilient Renewable Energy Microgrids

    Energy Technology Data Exchange (ETDEWEB)

    Anderson, Katherine H [National Renewable Energy Laboratory (NREL), Golden, CO (United States); DiOrio, Nicholas A [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Butt, Robert S [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Cutler, Dylan S [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Richards, Allison [Unaffiliated

    2017-11-14

    This presentation for the Cable-Tec Expo 2017 offers information about how renewable microgrids can be used to increase resiliency. It includes information about why renewable energy battery diesel hybrids microgrids should be considered for backup power, how to estimate economic savings of microgrids, quantifying the resiliency gain of microgrids, and where renewable microgrids will be successful.

  5. Investigating the effects of polymer molecular weight and non-solvent content on the phase separation, surface morphology and hydrophobicity of polyvinyl chloride films

    Science.gov (United States)

    Khoryani, Zahra; Seyfi, Javad; Nekoei, Mehdi

    2018-01-01

    The main aim of this research is to study the effects of polymer molecular weight as well as non-solvent concentration on the phase separation, surface morphology and wettability of polyvinyl chloride (PVC) films. Gel permeation chromatography (GPC) results showed that the Mn of the used PVC grades is 6 × 104, 8.7 × 104 and 1.26 × 105 g/mol. It was found that a proper combination of polymer molecular weight and non-solvent content could result in superhydrophobic and self-cleaning behaviors. Scanning electron microscopy (SEM) results demonstrated that addition of ethanol causes the polymer chains to be severely aggregated at the films' surface forming strand-like structures decorated by nano-scale polymer spheres. The polymer molecular weight was found to affect the degree of porosity which is highly influential on the hydrophobicity of the films. The mechanism of phase separation process was also discussed and it was found that the instantaneous demixing is the dominant mechanism once higher contents of non-solvent were used. However, a delayed demixing mechanism was detected when the lower molecular weight PVC has been used which resulted in a pore-less and dense skin layer. Differential scanning calorimetry was also utilized to study the crystallization and glass transition behavior of samples.

  6. Plasma membrane of a marine T cell lymphoma: surface labelling, membrane isolation, separation of membrane proteins and distribution of surface label amongst these proteins

    International Nuclear Information System (INIS)

    Crumpton, M.J.; Marchalonis, J.J.; Haustein, D.; Atwell, J.L.; Harris, A.W.

    1976-01-01

    Two established techniques for analysis of plasma membranes, namely, lactoperoxidase catalyzed surface radioiodination of intact cells and bulk membrane isolation following disruption of cells by shear forces, were applied in studies of membrane proteins of continuously cultured cells of the monoclonal T lymphoma line WEHI-22. It was found that macromolecular 125 I-iodide incorporated into plasma membrane proteins of intact cells was at least as good a marker for the plasma as was the commonly used enzyme 5'-nucleotidase, T lymphoma plasma membrane proteins were complex when analysed by polyacrylamide gel electrophoresis in sodium dodecylsulphate-containing buffers and more than thirty distinct components were resolved. More than fifteen of the components observed on a mass basis were also labelled with 125 I-iodide. Certain bands, however, exhibited a degree of label disproportionate to their staining properties with Coomassie Blue. This was interpreted in terms of their accessibility to the solvent in the intact cells. (author)

  7. Separation of surface, subsurface and volume fatigue damage effects in AISI 348 steel for power plant applications

    Energy Technology Data Exchange (ETDEWEB)

    Klein, Martin; Nowak, David; Walther, Frank [Technical Univ. Dortmund (Germany). Dept. of Materials Test Engineering (WPT); Starke, Peter [Saarland Univ., Saarbruecken (Germany). Chair of Non-Destructive Testing and Quality Assurance; Boller, Christian [Saarland Univ., Saarbruecken (Germany). Chair of Non-Destructive Testing and Quality Assurance; Fraunhofer IZFP, Saarbruecken (Germany)

    2016-08-01

    A wide range of industries including energy, chemistry, pharmacy, textiles, food and drink, pulp and paper, etc. is using stainless steels. Metastable austenitic steels such as used in power plants and chemical industry are subjected to cyclic mechanical and thermal loading in air as well as under the influence of corrosive media. This paper provides an overview on different nondestructive and electrochemical measurement techniques, which allow differentiating fatigue damage effects in total strain controlled multiple and constant amplitude tests with respect to damage appearance on surface, in subsurface area as well as in volume of specimens or components microstructure. In addition to conventional mechanical stress-strain hysteresis curves, electrical resistance, magnetic and open circuit potential measurements have been applied to characterize the cyclic deformation behavior of the metastable austenitic steel AISI 348 (X10CrNiNb18-9) in laboratory air and in distilled water. Based on these results obtained, the paper provides an outlook on the possibility for an efficient (remaining) fatigue life evaluation approach, which is adapted to the needs of the application areas.

  8. Mapping of renewable energies

    International Nuclear Information System (INIS)

    Boulanger, V.

    2013-01-01

    Germany is the champion of green energy in Europe: the contribution of renewable energies to electricity generation reached about 20% in 2011. This article describes the situation of renewable energies in Germany in 2011 with the help of 2 maps, the first one gives the installed electrical generation capacity for each region and for each renewable energy source (wind power, hydro-electricity, biomass, photovoltaic energy and biogas) and the second one details the total number of jobs (direct and indirect) for each renewable energy source and for each region. In 2011 about 372000 people worked in the renewable energy sector in Germany. (A.C.)

  9. Surface-enhanced Raman detection of RNA and DNA bases following flow-injection analysis or HPLC separation

    Science.gov (United States)

    Cotton, Therese M.; Sheng, Rong-Sheng; Ni, Fan

    1990-11-01

    The goal of this study is to develop Surface-enhanced Raman scattering (SERS) detection methods for flow injection analysis (FIA) and high performance liquid chromatography (HPLC). Nucleic acid bases have been chosen for analysis because of their importance in life processes. The advantages to the use of SERS-based detection include its sensitivity, specificity and versatility. With the development of improved methodology, the detection limits should be comparable to UV spectroscopy. However, the specificity is considerably superior to that obtained with electronic spectroscopy in that the Raman spectrum provides a molecular fingerprint of the individual analytes. Raman spectroscopy is very versatile: aqueous samples, gases and solids can be analyzed with equal facility. The results presented here demonstrate that SERS can be used as a detection method for both FIA and HPLC detection. In the following experiments Ag sols have been used as the active substrate. The effect of various parameters such as temperature, pH, flow rate, and the nature of the interface between the HPLC system and the Raman spectrometer have been examined. One of the most significant findings is that the temperature of the Ag sol/HPLC effluent mixture has a dramatic effect on the SERS intensities. This effect is a result of increased colloid aggregation at higher temperatures. Aggregation is known to produce greater enhancement in SERS and proceeds much more rapidly at elevated temperatures. An increase in the temperature of the Ag sol enables SERS detection under flowing conditions and in real time. This is a substantial improvement over many of the previous attempts to interface SERS detection to FIA or HPLC. In most of the previous studies, it was necessary to stop the flow as the analyte eluted from the chromatogram and measure the SERS spectra under static conditions.

  10. Renewable energy annual 1995

    International Nuclear Information System (INIS)

    1995-12-01

    The Renewable Energy Annual 1995 is the first in an expected series of annual reports the Energy Information Administration (EIA) intends to publish to provide a comprehensive assessment of renewable energy. This report presents the following information on the history, status, and prospects of renewable energy data: estimates of renewable resources; characterizations of renewable energy technologies; descriptions of industry infrastructures for individual technologies; evaluations of current market status; and assessments of near-term prospects for market growth. An international section is included, as well as two feature articles that discuss issues of importance for renewable energy as a whole. The report also contains a number of technical appendices and a glossary. The renewable energy sources included are biomass (wood), municipal solid waste, biomass-derived liquid fuels, geothermal, wind, and solar and photovoltaic

  11. Renewable energy annual 1995

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-12-01

    The Renewable Energy Annual 1995 is the first in an expected series of annual reports the Energy Information Administration (EIA) intends to publish to provide a comprehensive assessment of renewable energy. This report presents the following information on the history, status, and prospects of renewable energy data: estimates of renewable resources; characterizations of renewable energy technologies; descriptions of industry infrastructures for individual technologies; evaluations of current market status; and assessments of near-term prospects for market growth. An international section is included, as well as two feature articles that discuss issues of importance for renewable energy as a whole. The report also contains a number of technical appendices and a glossary. The renewable energy sources included are biomass (wood), municipal solid waste, biomass-derived liquid fuels, geothermal, wind, and solar and photovoltaic.

  12. Renewable Energy: Policy Considerations for Deploying Renewables

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2011-07-01

    This information paper accompanies the IEA publication Deploying Renewables 2011: Best and Future Policy Practice (IEA, 2011a). It provides more detailed data and analysis on policies for Deploying Renewables, and is intended to complement the main publication. It provides an account of the strategic drivers underpinning renewable energy (RE) technology deployment (energy security, economic development and environment protection) and assesses RE technologies with respect to these drivers, including an estimate of GHG emissions reductions due to RE technologies. The paper also explores the different barriers to deploying renewables at a given stage of market maturity and discusses what tools policy makers can avail of to succeed in removing deployment barriers. An additional topical highlight explores the challenges associated with accelerating the diffusion of RE technologies in developing countries.

  13. VT Renewable Energy Sites - Renewable Energy Professionals

    Data.gov (United States)

    Vermont Center for Geographic Information — (Link to Metadata) The Renewable Energy Atlas of Vermont and this dataset were created to assist town energy committees, the Clean Energy Development Fund and other...

  14. Renewable Substitutability Index: Maximizing Renewable Resource Use in Buildings

    OpenAIRE

    Srinivasan, Ravi; Campbell, Daniel; Wang, Wei

    2015-01-01

    In order to achieve a material and energy balance in buildings that is sustainable in the long run, there is an urgent need to assess the renewable and non-renewable resources used in the manufacturing process and to progressively replace non-renewable resources with renewables. Such progressive disinvestment in the non-renewable resources that may be substituted with renewable resources is referred to as “Renewable Substitutability” and if implemented, this process will lead to a paradigm sh...

  15. Separation of Cr(III) from Cr(VI) by Triton X-100 Cerium (Iv) Phosphate as a Surface Active Ion Exchanger

    International Nuclear Information System (INIS)

    El-Azony, K.M.; Ismail Aydia, M.; El-Mohty, A.A.

    2010-01-01

    A new and simple high-performance liquid chromatography (HPLC) method with ultraviolet (UV) detection has been developed for the determination of both Cr (III) and Cr (VI) ions. Chromium species were determined by HPLC using a stationary phase consisting of a reversed phase column (Nucleosil phenyl column; 250 mm x 4.6 mm,5 μm), and a mobile phase consisting of a mixture of methanol: water(70 : 30 v/v), in which the complexing agent di-(2-ethylhexyl) phosphoric acid (DEHPA) was dissolved. The UV detection was carried out at wavelength 650 nm. Separation of Cr (III) from Cr (VI) on Triton X-100 cerium(IV) phosphate(TX-100 CeP) as a surface active ion exchanger was investigated. TX-100 CeP has been synthesized, characterized using IR, X-Ray, TGA/DTA and elemental analysis. The ion exchange capacity and chemical stability in different HCl concentration have been studied

  16. Chromatographic separation and detection of contaminants from whole milk powder using a chitosan-modified silver nanoparticles surface-enhanced Raman scattering device.

    Science.gov (United States)

    Li, Dan; Lv, Di Y; Zhu, Qing X; Li, Hao; Chen, Hui; Wu, Mian M; Chai, Yi F; Lu, Feng

    2017-06-01

    Methods for the on-site analysis of food contaminants are in high demand. Although portable Raman spectroscopy is commonly used to test food on-site, it can be challenge to achieve this goal with rapid detection and inexpensive substrate. In this study, we detected trace food contaminants in samples of whole milk powder using the methods that combined chromatography with surface-enhanced Raman scattering detection (SERS). We developed a simple and efficient technique to fabricate the paper with chitosan-modified silver nanoparticles as a SERS-active substrate. The soaking time of paper and the concentration of chitosan solution were optimized for chromatographic separation and SERS detection. We then studied the separation properties for real applications including complex sample matrices, and detected melamine at 1mg/L, dicyandiamide at 100mg/L and sodium sulfocyanate at 10mg/L in whole milk powder. As such, our methods have great potential for field-based detection of milk contaminants. Copyright © 2016 Elsevier Ltd. All rights reserved.

  17. A separable surface-enhanced Raman scattering substrate modified with MIL-101 for detection of overlapping and invisible compounds after thin-layer chromatography development.

    Science.gov (United States)

    Zhang, Bin Bin; Shi, Yi; Chen, Hui; Zhu, Qing Xia; Lu, Feng; Li, Ying Wei

    2018-01-02

    By coupling surface-enhanced Raman spectroscopy (SERS) with thin-layer chromatography (TLC), a powerful method for detecting complex samples was successfully developed. However, in the TLC-SERS method, metal nanoparticles serving as the SERS-active substrate are likely to disturb the detection of target compounds, particularly in overlapping compounds after TLC development. In addition, the SERS detection of compounds that are invisible under both visible light and UV 254/365 after TLC development is still a significant challenge. In this study, we demonstrated a facile strategy to fabricate a TLC plate with metal-organic framework-modified gold nanoparticles as a separable SERS substrate, on which all separated components, including overlapping and invisible compounds, could be detected by a point-by-point SERS scan along the developing direction. Rhodamine 6G (R6G) was used as a probe to evaluate the performance of the substrate. The results indicated that the substrate provided good sensitivity and reproducibility, and optimal SERS signals could be collected in 5 s. Furthermore, this new substrate exhibited a long shelf life. Thus, our method has great potential for the sensitive and rapid detection of overlapping and invisible compounds in complex samples after TLC development. Copyright © 2017 The Author(s). Published by Elsevier B.V. All rights reserved.

  18. Separation and Determination of Honokiol and Magnolol in Chinese Traditional Medicines by Capillary Electrophoresis with the Application of Response Surface Methodology and Radial Basis Function Neural Network

    Science.gov (United States)

    Han, Ping; Luan, Feng; Yan, Xizu; Gao, Yuan; Liu, Huitao

    2012-01-01

    A method for the separation and determination of honokiol and magnolol in Magnolia officinalis and its medicinal preparation is developed by capillary zone electrophoresis and response surface methodology. The concentration of borate, content of organic modifier, and applied voltage are selected as variables. The optimized conditions (i.e., 16 mmol/L sodium tetraborate at pH 10.0, 11% methanol, applied voltage of 25 kV and UV detection at 210 nm) are obtained and successfully applied to the analysis of honokiol and magnolol in Magnolia officinalis and Huoxiang Zhengqi Liquid. Good separation is achieved within 6 min. The limits of detection are 1.67 µg/mL for honokiol and 0.83 µg/mL for magnolol, respectively. In addition, an artificial neural network with “3-7-1” structure based on the ratio of peak resolution to the migration time of the later component (Rs/t) given by Box-Behnken design is also reported, and the predicted results are in good agreement with the values given by the mathematic software and the experimental results. PMID:22291059

  19. Policies for Renewable Heat

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2012-07-01

    This paper builds on IEA publications, Deploying Renewables, Principles for Effective Policies and Deploying Renewables, Best and Future Policy Practice, that discuss the 'integrated policy approach,' whereby renewable energy technologies require different support policies at different stages of their maturity pathways. The paper discusses how the integrated policy approach applies to renewable heat. It attempts to provide guidance for policy-makers on renewable heat throughout the different phases of the policy lifecycle, allowing for the specific challenges of renewable heat and needs of the many stakeholders involved. Stimulating a market for heat involves challenges that are different and, often, more difficult to overcome than in the electricity and transport sectors.

  20. China's renewables law

    International Nuclear Information System (INIS)

    Zhu Li

    2005-01-01

    The paper discusses China's Renewable Energy Promotion Law which will come into force in January 2006. The law shows China's commitment to renewable energy sources. The target is to raise the country's energy consumption from renewables to 10% by 2020. Data for current capacity, and expected capacity by 2020, are given for wind power, solar power, biomass and hydroelectric power. The financial and technological hurdles which China must overcome are mentioned briefly

  1. Renewable energy resources

    CERN Document Server

    Twidell, John

    2015-01-01

    Renewable Energy Resources is a numerate and quantitative text covering the full range of renewable energy technologies and their implementation worldwide. Energy supplies from renewables (such as from biofuels, solar heat, photovoltaics, wind, hydro, wave, tidal, geothermal, and ocean-thermal) are essential components of every nation's energy strategy, not least because of concerns for the local and global environment, for energy security and for sustainability. Thus in the years between the first and this third edition, most renewable energy technologies have grown from fledgling impact to s

  2. The renewable chemicals industry

    DEFF Research Database (Denmark)

    Christensen, Claus H.; Rass-Hansen, J.; Marsden, Charlotte Clare

    2008-01-01

    per kilogram of desired product to illustrate in which processes the use of renewable resources lead to the most substantial reduction of CO2 emissions. The steps towards a renewable chemicals industry will most likely involve intimate integration of biocatalytic and conventional catalytic processes......The possibilities for establishing a renewable chemicals industry featuring renewable resources as the dominant feedstock rather than fossil resources are discussed in this Concept. Such use of biomass can potentially be interesting from both an economical and ecological perspective. Simple...

  3. Renewables. The clean advantage

    International Nuclear Information System (INIS)

    Klein, A.

    2006-01-01

    Europe's big utilities are increasingly seeing renewable energy as a viable alternative to conventional forms of power generation which at present have disadvantages in terms of cost and/or environment. Europe's biggest 20 utilities aim to double their renewables capacity in the next five years and nearly 20 billion US dollars have been earmarked for such projects. This report by Emerging Energy Research discusses the likely trends for the next five years. The various sources of renewable energy and how they might be developed are discussed. The companies leading exploitation of renewables and their market share are named

  4. Optimising reversed-phase liquid chromatographic separation of an acidic mixture on a monolithic stationary phase with the aid of response surface methodology and experimental design.

    Science.gov (United States)

    Wang, Y; Harrison, M; Clark, B J

    2006-02-10

    An optimization strategy for the separation of an acidic mixture by employing a monolithic stationary phase is presented, with the aid of experimental design and response surface methodology (RSM). An orthogonal array design (OAD) OA(16) (2(15)) was used to choose the significant parameters for the optimization. The significant factors were optimized by using a central composite design (CCD) and the quadratic models between the dependent and the independent parameters were built. The mathematical models were tested on a number of simulated data set and had a coefficient of R(2) > 0.97 (n = 16). On applying the optimization strategy, the factor effects were visualized as three-dimensional (3D) response surfaces and contour plots. The optimal condition was achieved in less than 40 min by using the monolithic packing with the mobile phase of methanol/20 mM phosphate buffer pH 2.7 (25.5/74.5, v/v). The method showed good agreement between the experimental data and predictive value throughout the studied parameter space and were suitable for optimization studies on the monolithic stationary phase for acidic compounds.

  5. Acoustofluidic bacteria separation

    International Nuclear Information System (INIS)

    Li, Sixing; Huang, Tony Jun; Ma, Fen; Zeng, Xiangqun; Bachman, Hunter; Cameron, Craig E

    2017-01-01

    Bacterial separation from human blood samples can help with the identification of pathogenic bacteria for sepsis diagnosis. In this work, we report an acoustofluidic device for label-free bacterial separation from human blood samples. In particular, we exploit the acoustic radiation force generated from a tilted-angle standing surface acoustic wave (taSSAW) field to separate Escherichia coli from human blood cells based on their size difference. Flow cytometry analysis of the E. coli separated from red blood cells shows a purity of more than 96%. Moreover, the label-free electrochemical detection of the separated E. coli displays reduced non-specific signals due to the removal of blood cells. Our acoustofluidic bacterial separation platform has advantages such as label-free separation, high biocompatibility, flexibility, low cost, miniaturization, automation, and ease of in-line integration. The platform can be incorporated with an on-chip sensor to realize a point-of-care sepsis diagnostic device. (paper)

  6. Acoustofluidic bacteria separation

    Science.gov (United States)

    Li, Sixing; Ma, Fen; Bachman, Hunter; Cameron, Craig E.; Zeng, Xiangqun; Huang, Tony Jun

    2017-01-01

    Bacterial separation from human blood samples can help with the identification of pathogenic bacteria for sepsis diagnosis. In this work, we report an acoustofluidic device for label-free bacterial separation from human blood samples. In particular, we exploit the acoustic radiation force generated from a tilted-angle standing surface acoustic wave (taSSAW) field to separate Escherichia coli from human blood cells based on their size difference. Flow cytometry analysis of the E. coli separated from red blood cells shows a purity of more than 96%. Moreover, the label-free electrochemical detection of the separated E. coli displays reduced non-specific signals due to the removal of blood cells. Our acoustofluidic bacterial separation platform has advantages such as label-free separation, high biocompatibility, flexibility, low cost, miniaturization, automation, and ease of in-line integration. The platform can be incorporated with an on-chip sensor to realize a point-of-care sepsis diagnostic device.

  7. Developing the use of renewable heat

    International Nuclear Information System (INIS)

    Nifenecker, Herve

    2013-01-01

    The author reports a study in which he shows that the heat production by means of renewable energies is an efficient method to reach the objective of 23 per cent of renewable energies in the French final energy consumption. He browses the different techniques of renewable heat production (solar heat, wood-fuel, surface geothermal) and indicates the associated potential resources. He proposes a cost analysis which compares the use of gas and electricity with three techniques of production of renewable heat: solar heat to produce hot water, biomass combustion (more particularly wood), solar heat extracted with fuel cells. He also assesses tariffs and CO 2 emissions. Then, he elaborates a strategy to phase out fossil energies: a modification of the RT 2012 thermal regulation, to give up the purchase obligation for electricity produced by wind and photovoltaic energy, to extend the CSPE calculation basis, to put oil-fuel and gas boilers out of the market, to support the development of renewable heat production, to improve the competitiveness of the different techniques of renewable heat production. He finally gives a brief overview of industrial perspectives created by such a development of renewable heat

  8. Marine Renewable Energies

    DEFF Research Database (Denmark)

    Azzellino, Arianna; Conley, Daniel; Vicinanza, Diego

    2013-01-01

    Countries with coastlines may have valuable renewable energy resources in the form of tides, currents, waves, and offshorewind.The potential to gather energy from the sea has recently gained interest in several nations, so Marine Renewable Energy Installations (hereinafter MREIs) will likely become...

  9. Renewable Resources in SA

    CSIR Research Space (South Africa)

    Mushwana, C

    2015-02-01

    Full Text Available Renewable energy is derived form natural resources that are replenished at a faster rate than they are consumed, and thus cannot be depleted. Solar, wind, geothermal, hydro, and some forms of biomass are common sources of renewable energy. Almost 90...

  10. Renewable Energy in Alaska

    Energy Technology Data Exchange (ETDEWEB)

    2013-03-01

    This report examines the opportunities, challenges, and costs associated with renewable energy implementation in Alaska and provides strategies that position Alaska's accumulating knowledge in renewable energy development for export to the rapidly growing energy/electric markets of the developing world.

  11. Renewable Energy Technology

    Science.gov (United States)

    Daugherty, Michael K.; Carter, Vinson R.

    2010-01-01

    In many ways the field of renewable energy technology is being introduced to a society that has little knowledge or background with anything beyond traditional exhaustible forms of energy and power. Dotson (2009) noted that the real challenge is to inform and educate the citizenry of the renewable energy potential through the development of…

  12. On the importance of PURE - Public Understanding of Renewable Energy

    Energy Technology Data Exchange (ETDEWEB)

    Broman, Lars; Kandpal, Tara C.

    2013-09-15

    Public understanding of science (PUS) is a central concept among science communicators. Public understanding of renewable energy (PURE) is proposed as an important sub-concept of PUS. The aim of this paper is to interest and invite renewable energy scientists to join a PURE research project. Four separate important questions for a PURE research project can be identified: (A) Is PURE important? (B) Which issues of PURE are the most important ones, according to renewable energy scientists? (C) What understanding of renewable energy has the general public today, worldwide? (D) How to achieve PURE?.

  13. Renewable energy resources: Opportunities and constraints 1990-2020

    International Nuclear Information System (INIS)

    1993-09-01

    This study examined the prospects for new renewable energy resources, from a global perspective, over the next three decades and beyond. The study is intended to support the work of the World Energy Council (WEC) Commission on Energy for Tomorrow's World. The new renewable resources investigated were: Solar; wind; geothermal; modern biomass; ocean; small hydro. Each of these areas was thoroughly researched and was the subject of a separate section of the report. Recent information on large-scale hydroelectric and traditional biomass is included for added perspective on total use of renewable energy, but both fall outside the definition of new renewable energy used in this report

  14. Renewable energy export network

    International Nuclear Information System (INIS)

    Anon

    2000-01-01

    A Renewable Energy Exporters Network (REEN) has recently been established, following a meeting of renewable energy exporters and government agencies on 30 October 2000. REEN will assist the Australian renewable energy industry to take advantage of the opportunities offered by the burgeoning global market for renewable energy goods and services. Recent estimates of the significant potential global growth is renewable energy demand have reinforced the industry and Government's view that, in the medium to long-term, growth in the Australian renewable energy industry will largely depend on capturing export market share. Expanding the export market was identified as a crucial component in the Renewable Energy Action Agenda, developed jointly by industry and Government and released in June 2000. It was estimated that, for the industry to achieve its vision of sales of $4 billion per year by 2010, exports would need to comprise approximately 50% of the forecast growth in sales. As such, the need for a specific export strategy for the Australian renewable energy industry was recognised in the Action Agenda, and the establishment of the REEN is one of the first initiatives undertaken as part of the Renewable Energy Export Strategy. The REEN comprises approximately 50 export-ready renewable energy companies, the Department of Industry, Science and Resources, Austrade, and Stage Government agencies such as NSW's Sustainable Energy Development Authority. The Export Network will operate electronically, with face-to-face meetings held as appropriate. The Department of Industry, Science and Resources will facilitate the Export Network and has published a website at www.isr.gov.au/industry/reen. The site includes: a members directory; a discussion forum; information on opportunities to showcase Australian renewable; energy products and services; and Iinks to sites containing information that may be useful to renewable energy exporters. Other actions that are being undertaken as

  15. Nuclear plant license renewal

    International Nuclear Information System (INIS)

    Gazda, P.A.; Bhatt, P.C.

    1991-01-01

    During the next 10 years, nuclear plant license renewal is expected to become a significant issue. Recent Electric Power Research Institute (EPRI) studies have shown license renewal to be technically and economically feasible. Filing an application for license renewal with the Nuclear Regulatory Commission (NRC) entails verifying that the systems, structures, and components essential for safety will continue to perform their safety functions throughout the license renewal period. This paper discusses the current proposed requirements for this verification and the current industry knowledge regarding age-related degradation of structures. Elements of a license renewal program incorporating NRC requirements and industry knowledge including a schedule are presented. Degradation mechanisms for structural components, their significance to nuclear plant structures, and industry-suggested age-related degradation management options are also reviewed

  16. New renewable energy sources

    International Nuclear Information System (INIS)

    2001-06-01

    This publication presents a review of the technological, economical and market status in the field of new renewable energy sources. It also deals briefly with the present use of energy, external conditions for new renewable energy sources and prospects for these energy sources in a future energy system. The renewable energy sources treated here are ''new'' in the sense that hydroelectric energy technology is excluded, being fully developed commercially. This publication updates a previous version, which was published in 1996. The main sections are: (1) Introduction, (2) Solar energy, (3) Bio energy, (4) Wind power, (5) Energy from the sea, (6) Hydrogen, (7) Other new renewable energy technologies and (8) New renewable s in the energy system of the future

  17. NRC's license renewal regulations

    International Nuclear Information System (INIS)

    Akstulewicz, Francis

    1991-01-01

    In order to provide for the continuity of the current generation of nuclear power plant operating licenses and at the same time ensure the health and safety of the public, and the quality of the environment, the US Nuclear Regulatory Commission (NRC) established a goal of developing and issuing regulations and regulatory guidance for license renewal in the early 1990s. This paper will discuss some of those activities underway to achieve this goal. More specifically, this paper will discuss the Commission's regulatory philosophy for license renewal and the two major license renewal rule makings currently underway. The first is the development of a new Part 54 to address procedural and technical requirements for license renewal; the second is a revision to existing Part 51 to exclude environmental issues and impacts from consideration during the license renewal process. (author)

  18. Renewable energy resources

    DEFF Research Database (Denmark)

    Ellabban, Omar S.; Abu-Rub, Haitham A.; Blaabjerg, Frede

    2014-01-01

    Electric energy security is essential, yet the high cost and limited sources of fossil fuels, in addition to the need to reduce greenhouse gasses emission, have made renewable resources attractive in world energy-based economies. The potential for renewable energy resources is enormous because...... they can, in principle, exponentially exceed the world's energy demand; therefore, these types of resources will have a significant share in the future global energy portfolio, much of which is now concentrating on advancing their pool of renewable energy resources. Accordingly, this paper presents how...... renewable energy resources are currently being used, scientific developments to improve their use, their future prospects, and their deployment. Additionally, the paper represents the impact of power electronics and smart grid technologies that can enable the proportionate share of renewable energy...

  19. Research of the value of linear distortion of renewable surface of part during rotary processing of bulky items without dismantling unit

    Science.gov (United States)

    Bondarenko, J. A.; Fedorenko, M. A.; Pogonin, A. A.

    2018-03-01

    The loading and unloading units and grinding mills of raw devices have internal cone type or pipe screw perceive load of incoming and outgoing material. The main part of the support assembly is a pin. Mounting seats for the pipe screws cone have traces of deformation and work hardening, while they themselves have wear of pins and deformation of the inner and outer cylindrical working surface. In the mill body, there are constantly acting dynamic forces causing vibration, which are transmitted to the stud and inner accelerating elements. Under the influence of stress and vibration, the housing spigot is in the stress-compressed state and stretched vertically and horizontally. As a result, the insertion element is deformed and weakened in the fixture. A moving element appears in the gap leading to the fact that it drops lfeedstock and under the influence of variable loads it is destroyed, as well as the seating surfaces of the insert pin member.

  20. Separation of flow

    CERN Document Server

    Chang, Paul K

    2014-01-01

    Interdisciplinary and Advanced Topics in Science and Engineering, Volume 3: Separation of Flow presents the problem of the separation of fluid flow. This book provides information covering the fields of basic physical processes, analyses, and experiments concerning flow separation.Organized into 12 chapters, this volume begins with an overview of the flow separation on the body surface as discusses in various classical examples. This text then examines the analytical and experimental results of the laminar boundary layer of steady, two-dimensional flows in the subsonic speed range. Other chapt

  1. A comparison of cellulosic fuel yields and separated soil-surface CO2 fluxes in maize and prairie biofuel cropping systems

    Science.gov (United States)

    Nichols, Virginia A.

    It has been suggested that strategic incorporation of perennial vegetation into agricultural landscapes could provide ecosystem services while maintaining agricultural productivity. To evaluate potential use of prairie as a Midwestern cellulosic feedstock, we investigated theoretical cellulosic fuel yields, as well as soil-surface carbon dioxide emissions of prairie-based biofuel systems as compared to maize-based systems on fertile soils in Boone County, IA, USA. Investigated systems were: a maize-soybean rotation grown for grain only, continuous maize grown for grain and stover both with and without a winter rye cover crop, and a 31-species reconstructed prairie grown with and without spring nitrogen fertilization for fall-harvested biomass. From 2009-2013, the highest producing system was N-fertilized prairie, averaging 10.4 Mg ha -1 yr-1 above-ground biomass with average harvest removals of 7.8 Mg ha-1 yr-1. The unfertilized prairie produced 7.4 Mg ha-1 yr-1, averaging harvests of 5.3 Mg ha-1 yr-1. Lowest cellulosic biomass harvests were realized from continuous maize systems, averaging 3.5 Mg ha -1 yr-1 when grown with, and 3.7 Mg ha-1 yr-1 when grown without a winter rye cover crop, respectively. Un-fertilized prairie biomass and maize stover had equivalent dietary conversion ratios at 330 g ethanol kg-1 dry biomass, but N-fertilized prairie was lower at 315. Over four years prairie systems averaged 1287 L cellulosic ethanol ha-1 yr-1 more than maize systems, with fertilization increasing prairie ethanol production by 865 L ha-1 yr-1. Harvested biomass accounted for >90% of ethanol yield variation. A major hurdle in carbon cycling studies is the separation of the soil-surface CO2 flux into its respective components. From 2012-2013 we used a shading method to separate soil-surface CO2 resulting from oxidation of soil organic matter and CO2 derived from live-root activity in three systems: unfertilized prairie, N-fertilized prairie, and continuous maize

  2. Renewable Energy in Romania after 2007

    Directory of Open Access Journals (Sweden)

    Daniela Enachescu

    2016-07-01

    Full Text Available Sustainable development requires obtaining energy from alternative sources which are clean and sustainable. In Romania, there are categories of renewable energy that basically were not used, such as solar PV and wind energy by 2007. Even today, their share is minor compared to energy from conventional sources, but they were made important steps, including in legislation domain. The paper aims to present the evolution of renewable energy in Romania after 2007, as a result of EU integration. The analysis is done separately for installed capacity in the following chapters: Hydropower, Wind Onshore, Solid biomass, Solar Photovoltaic and Biogas.

  3. Gains from an integrated market for tradable renewable energy credits

    International Nuclear Information System (INIS)

    Mozumder, Pallab; Marathe, Achla

    2004-01-01

    Decoupling the environmental attributes of renewable energy (RE) generation from the physical unit of energy is an innovative mechanism for marketing green or renewable power. The introduction of 'Tradable Renewable Energy Credits' (TRECs) allows the green power attributes of energy to be sold or traded separately from the physical unit of energy. Since the green power certificate system removes potential locational and physical bottlenecks, both suppliers and consumers gain flexibility in the marketplace. The TREC is also an efficient tool to meet 'Renewable Portfolio Standard' (RPS) required by different states in the US. This paper discusses the RPS requirements for different states and examines the implications of an integrated TREC market. It offers a competitive setting to the consumers to pay for renewable energy and a cost effective tool to support renewable energy generation [Grace and Wiser, 2002]. This paper also highlights some practical difficulties that should be addressed in order to establish an efficient integrated TREC market

  4. Emerging Markets for Renewable Energy Certificates: Opportunities and Challenges

    Energy Technology Data Exchange (ETDEWEB)

    Holt, E.; Bird, L.

    2005-01-01

    Renewable energy certificates (RECs) represent the attributes of electricity generated from renewable energy sources. These attributes are unbundled from the physical electricity, and the two products-the attributes embodied in the certificates and the commodity electricity-may be sold or traded separately. RECs are quickly becoming the currency of renewable energy markets because of their flexibility and the fact that they are not subject to the geographic and physical limitations of commodity electricity. RECs are currently used by utilities and marketers to supply renewable energy products to end-use customers as well as to demonstrate compliance with regulatory requirements, such as renewable energy mandates. The purpose of this report is to describe and analyze the emerging market for renewable energy certificates. It describes how RECs are marketed, examines RECs markets including scope and prices, and identifies and describes the key challenges facing the growth and success of RECs markets.

  5. Renewables in the Midwest

    International Nuclear Information System (INIS)

    Wager, J.S.

    1994-01-01

    Over the past three years, the Union of Concerned Scientists (UCS) has evaluated the potential for using renewable energy for electricity in the Midwest, and has been carrying out a multifaceted effort to expand the use of renewables in the region. The UCS study presents a strategy for developing renewable-electric technologies and resources in 12 midwestern states. UCS analysts used a geographic information system (GIS) to create data-bases of renewable resources, land uses, vegetation cover, terrain elevation and locations of utility transmission lines, and to analyze and present information on a .6 mi x .6 mi (1 km x 1 km) grid scale. In addition, UCS developed a model to calculate the net employment impact of renewable versus conventional electricity technologies on a state-by-state basis. In evaluating the costs and benefits of renewable energy sources, UCS analysts explored a cost assessment that accounted for the impact of pollution from fossil fuels on energy resource cost. Researchers also considered the risks associated with fuel-price volatility, environmental regulation, construction lead times and other uncertainties. Finally, UCS researchers suggested steps to remove the institutional, regulatory and legislative barriers that inhibit renewable energy development, and proposed policies to expand the use of the region's renewable resources. The UCS analysis showed that wind is currently the least expensive renewable resource. UCS also found numerous opportunities to expand biomass-electric generation in the near term, such as converting small coal-fired power plants to wood fuel, making greater use of logging residues and co-firing a small percentage of biomass with fossil fuel at large power plants

  6. Separation of Cr(III) from Cr(VI) by Triton X-100 cerium(IV) phosphate as a surface active ion exchanger

    International Nuclear Information System (INIS)

    El-Azony, K.M.; Ismail Aydia, M.; El-Mohty, A.A.

    2011-01-01

    Triton X-100 cerium(IV) phosphate (TX-100CeP) was synthesized and characterized by using IR, X-ray, TGA/DT and the elemental analysis. The chemical stability of TX-100CeP versus the different concentrations of HCl acid was studied before and after its exposure to the radiation dose (30 K Gray). The effect of HCl concentration on separation of Cr(III) from Cr(VI) by using TX-100CeP as surface active ion exchanger was also studied. A novel method was achieved for the quantifying of Cr(III) and Cr(VI) ions by using the high-performance liquid chromatography (HPLC) at wavelength 650 nm, a stationary phase consists of reversed phase column (Nucleosil phenyl column; 250 x 4.6 mm, 5 μm), and a mobile phase consists of 0.001 M di-(2-ethylhexyl) phosphoric acid (DEHPA) in methanol:water (70:30 v/v). The retention times were 7.0 and 8.5 min, for the Cr(III) and Cr(VI), respectively. The exchange capacity of Cr(III) was quantified (2.1 meq/g) onto the TX-100CeP. (author)

  7. Damn renewable energies

    International Nuclear Information System (INIS)

    Gay, Michel

    2017-01-01

    In this book, the author describes how renewable energies have been developed in a way he considers as scandalous, whereas they are a technical, financial and ecological dead end. He also explains how ecologists (notably the ADEME) manipulate figures to make believe that these energies could be an answer to the needs of France, of Europe and of humanity. In a first chapter, he criticises the influence of a so-called green ideology on the design of energy transition. In the second one, he denounces twelve tales about energy transition. In the next chapters, he denounces the sham of renewable energies, and finally tells some unfortunate renewable experiments

  8. Renewable energies - Alain Chardon

    International Nuclear Information System (INIS)

    Anon.

    2012-01-01

    In an interview, the chairman of Cleantechs and Decarbonate, Capgemini Consulting, comments the challenge of the struggle against global warming, discusses the role of gas on the way towards a de-carbonated economy, the cost of renewable energies compared to that of fossil and nuclear energies. He outlines other brakes upon the development of renewable energies, discusses the political issues and the challenge of meeting European objectives with respect with the share of renewable energies in the energy mix and the electricity mix by 2020

  9. Renewable Energy Development in India

    Energy Technology Data Exchange (ETDEWEB)

    Gupta, K.M.

    2007-07-01

    India has done a significant progress in the power generation in the country. The installed generation capacity was 1300 megawatt (MW) at the time of Independence i.e. about 60 years back. The total generating capacity anticipated at the end of the Tenth Plan on 31-03-2007, is 1, 44,520 MW which includes the generation through various sectors like Hydro, Thermal and Nuclear. Emphasis is given to the renewable energy programme towards gradual commercialization. This programme is looked after by the Ministry of Non-Conventional Sources of energy. Since the availability of fossil fuel is on the decline therefore, in this backdrop the norms for conventional or renewable sources of energy (RSE) is given importance not only in India but has attracted the global attention. The main items under RSE are as follows: (i) Hydro Power (ii) Solar Power (iii) Wind Power (iv) Bio-mass Power (v) Energy from waste (vi) Ocean energy, and (vii) Alternative fuel for surface transportation. Evolution of power transformer technology in the country during the past five decades is quite impressive. There are manufacturers in the country with full access to the latest technology at the global level. Some of the manufacturers have impressive R&D set up to support the technology. Renewable energy is very much promoted by the Chinese Government. At the same time as the law was passed, the Chinese Government set a target for renewable energy to contribute 10% of the country's gross energy consumption by 2020, a huge increase from the current 1%. It has been felt that there is rising demand for energy, food and raw materials by a population of 2.5 billion Chinese and Indians. Both these countries have large coal dominated energy systems in the world and the use of fossil fuels such as coal and oil releases carbon dioxide (CO2) into the air which adds to the greenhouse gases which lead to global warming. (auth)

  10. Isotope separation

    International Nuclear Information System (INIS)

    Eerkens, J.W.

    1979-01-01

    A method of isotope separation is described which involves the use of a laser photon beam to selectively induce energy level transitions of an isotope molecule containing the isotope to be separated. The use of the technique for 235 U enrichment is demonstrated. (UK)

  11. Designing and developing an accreditation scheme for renewable energy with full consultation of interested parties

    Energy Technology Data Exchange (ETDEWEB)

    Denne, T.; Wakerley, S.

    1998-11-01

    This document sets out a plan for the development of a labelling system to promote consumer sales of New and Renewable Electricity. A New and Renewable Electricity Verification Scheme is a mechanism to assist the development of an end-user market in new and renewable electricity. It provides two key features: a means for separately tracking new and renewable electricity using a methodology for verifying generation source; and a label for identifying new and renewable electricity (NRE) as a distinct product. The objectives of the scheme would be to: provide customers wishing to purchase NRE with confidence in the product; and to provide value to the new and renewable energy sector. (author)

  12. Renewable energy in Taiwan

    International Nuclear Information System (INIS)

    Chen, Falin; Lu, Shyi-Min; Wang, Eric; Tseng, Kuo-Tung

    2010-01-01

    With limited indigenous conventional energy resources, Taiwan imports over 99% of its energy supply from foreign countries, mostly from the Middle East. Developing independent renewable energy resources is thus of priority concern for the Taiwanese government. A medium subtropical island surrounded by the Pacific Ocean, Taiwan has enormous potential to develop various renewable energies, such as solar energy, biomass energy, wind power, geothermal energy, hydropower, etc. However, owing to the importance of conventional fossil energy in generating exceptionally cheap electricity, renewable energy has not yet fully developed in Taiwan, resulting from a lack of market competition. Consequently, numerous promotional and subsidy programs have recently been proclaimed by the Taiwanese government, focused on the development of various renewables. This study reviews the achievements, polices and future plans in this area. (author)

  13. The value of renewables

    International Nuclear Information System (INIS)

    Koch, H.J.

    2001-01-01

    The article extols the virtues of renewable energy sources. Based largely on the outcome of an IAE meeting in May 2001, the author has outlined an approach for accelerating the development of renewables. The article quotes several statements made by the IAE with respect to the need for a secure supply of affordable energy, sustainable development, diversification, the value of renewables and challenges confronting developers of renewables. The article is presented under the sub-headings of: (i) harnessing energy market forces; (ii) understanding costs in the context of diversification; (iii) economic performance; (iv) environmental protection; (v) an IAE action plan and (vi) conclusions. The author was once the IAE's director for energy efficiency, technology and R and D

  14. Biotechnology for renewable chemicals

    DEFF Research Database (Denmark)

    Borodina, Irina; Kildegaard, Kanchana Rueksomtawin; Jensen, Niels Bjerg

    2014-01-01

    The majority of the industrial organic chemicals are derived from fossil sources. With the oil and gas resources becoming limiting, biotechnology offers a sustainable alternative for production ofchemicals from renewable feedstocks. Yeast is an attractive cell factory forsustainable production...

  15. Foundations for renewables

    Energy Technology Data Exchange (ETDEWEB)

    Neidlein, H.C. [German Agency Scherer Schnell Walser und Partner (Germany)

    2007-07-01

    In Germany, 77 foundations promote renewable energy technology with around Euro 25 million annually. The most important internationally active foundations, however, can be found in the Anglo-Saxon countries. (orig.)

  16. Renewable resources - future possibilities

    International Nuclear Information System (INIS)

    Thomas, Martin H.

    1998-01-01

    The paper describes the Australian Cooperative Research Centre for Renewable Energy and Related Greenhouse Gas Abatement Technologies (ACRE), its technologies, commercial relationships and markets. The relevance of ACRE to developing country communities which lack reliable, adequate power supplies, is discussed. The opportunities for mutual collaboration between Australia and the developing countries in the application of renewable energy have never been stronger. Renewable energy promises real advantages to those who deploy it wisely, as well as significant job creation. Education at all level together with operational training, public awareness of what is possible and increased system reliability, are also vital ingredients for acceptance of these new technologies. They underpin successful commercialisation. The author concludes with the hope for a united international cooperative approach to the development of the renewable energy industry. (author)

  17. Promoting renewable energy technologies

    International Nuclear Information System (INIS)

    Grenaa Jensen, S.

    2004-06-01

    Technologies using renewable energy sources are receiving increasing interest from both public authorities and power producing companies, mainly because of the environmental advantages they procure in comparison with conventional energy sources. These technologies can be substitution for conventional energy sources and limit damage to the environment. Furthermore, several of the renewable energy technologies satisfy an increasing political goal of self-sufficiency within energy production. The subject of this thesis is promotion of renewable technologies. The primary goal is to increase understanding on how technological development takes place, and establish a theoretical framework that can assist in the construction of policy strategies including instruments for promotion of renewable energy technologies. Technological development is analysed by through quantitative and qualitative methods. (BA)

  18. Renewable Heating And Cooling

    Science.gov (United States)

    Renewable heating and cooling is a set of alternative resources and technologies that can be used in place of conventional heating and cooling technologies for common applications such as water heating, space heating, space cooling and process heat.

  19. Renewable Energy Tracking Systems

    Science.gov (United States)

    Renewable energy generation ownership can be accounted through tracking systems. Tracking systems are highly automated, contain specific information about each MWh, and are accessible over the internet to market participants.

  20. Renewable energy in Taiwan

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Falin; Lu, Shyi-Min; Wang, Eric; Tseng, Kuo-Tung [Institute of Applied Mechanics, National Taiwan University, Taipei 10617 (China)

    2010-09-15

    With limited indigenous conventional energy resources, Taiwan imports over 99% of its energy supply from foreign countries, mostly from the Middle East. Developing independent renewable energy resources is thus of priority concern for the Taiwanese government. A medium subtropical island surrounded by the Pacific Ocean, Taiwan has enormous potential to develop various renewable energies, such as solar energy, biomass energy, wind power, geothermal energy, hydropower, etc. However, owing to the importance of conventional fossil energy in generating exceptionally cheap electricity, renewable energy has not yet fully developed in Taiwan, resulting from a lack of market competition. Consequently, numerous promotional and subsidy programs have recently been proclaimed by the Taiwanese government, focused on the development of various renewables. This study reviews the achievements, polices and future plans in this area. (author)

  1. Renewable Substitutability Index: Maximizing Renewable Resource Use in Buildings

    Science.gov (United States)

    In order to achieve a material and energy balance in buildings that is sustainable in the long run, there is an urgent need to assess the renewable and non-renewable resources used in the manufacturing process and to progressively replace non-renewable resources with renewables. ...

  2. License renewal process

    International Nuclear Information System (INIS)

    Fable, D.; Prah, M.; Vrankic, K.; Lebegner, J.

    2004-01-01

    The purpose of this paper is to provide information about license renewal process, as defined by Nuclear Regulatory Commission (NRC). The Atomic Energy Act and NRC regulations limit commercial power reactor licenses to an initial 40 years but also permit such licenses to be renewed. This original 40-year term for reactor licenses was based on economic and antitrust considerations not on limitations of nuclear technology. Due to this selected time period; however, some structures and components may have been engineered on the basis of an expected 40-year service life. The NRC has established a timely license renewal process and clear requirements codified in 10 CFR Part 51 and 10 CFR Part 54, that are needed to assure safe plant operation for extended plant life. The timely renewal of licenses for an additional 20 years, where appropriate to renew them, may be important to ensuring an adequate energy supply during the first half of the 21st Century. License renewal rests on the determination that currently operating plants continue to maintain adequate levels of safety, and over the plant's life, this level has been enhanced through maintenance of the licensing bases, with appropriate adjustments to address new information from industry operating experience. Additionally, NRC activities have provided ongoing assurance that the licensing bases will continue to provide an acceptable level of safety. This paper provides additional discussion of license renewal costs, as one of key elements in evaluation of license renewal justifiability. Including structure of costs, approximately value and two different approaches, conservative and typical. Current status and position of Nuclear Power Plant Krsko, related to license renewal process, will be briefly presented in this paper. NPP Krsko is designed based on NRC Regulations, so requirements from 10 CFR 51, and 10 CFR 54, are applicable to NPP Krsko, as well. Finally, this paper will give an overview of current status of

  3. Power electronics for renewable and distributed energy systems a sourcebook of topologies, control and integration

    CERN Document Server

    Chakraborty, Sudipta; Kramer, William E

    2013-01-01

    While most books approach power electronics and renewable energy as two separate subjects, Power Electronics for Renewable and Distributed Energy Systems takes an integrative approach; discussing power electronic converters topologies, controls and integration that are specific to the renewable and distributed energy system applications. An overview of power electronic technologies is followed by the introduction of various renewable and distributed energy resources that includes photovoltaics, wind, small hydroelectric, fuel cells, microturbines and variable speed generation. Energy storage s

  4. Processes of Strategic Renewal,

    OpenAIRE

    Harald Aadne, John; Mahnke, Volker

    2010-01-01

    We discuss strategic renewal from a competence perspective. We argue that the management of speed and timing in this process is viewed distinctively when perceived through a cognitive lens. Managers need more firmly grounded process-understanding. The key idea of this paper is to dynamically conceptualize key activities of strategic renewal, and possible sources of break-down as they relate to the managment of speed and timing. Based on a case from the media industry, we identi...

  5. Promoting renewable energy technologies

    DEFF Research Database (Denmark)

    Olsen, O.J.; Skytte, K.

    2004-01-01

    % of its annual electricity production. In this paper, we present and discuss the Danish experience as a case of promoting renewable energy technologies. The development path of the two technologies has been very different. Wind power is considered an outright success with fast deployment to decreasing...... technology and its particular context, it is possible to formulate some general principles that can help to create an effective and efficient policy for promoting new renewable energy technologies....

  6. Identifying the hotspots of non-renewable water use using HiGW-MAT: A new land surface model coupled with human interventions and ground water reservoir

    Science.gov (United States)

    Oki, T.; Pokhrel, Y. N.; Yeh, P. J.; Koirala, S.; Kanae, S.; Hanasaki, N.

    2011-12-01

    The real hydrological cycles on the Earth are not natural anymore. Global hydrological model simulations of the water cycle and available water resources should have an ability to consider the effects of human interventions on hydrological cycles. Anthropogenic activity modules (Hanasaki et al., 2008), such as reservoir operation, crop growth and water demand in crop lands, and environmental flows, were incorporated into a land surface model called MATSIRO (Takata et al., 2003), to form a new model, MAT-HI (Pokhrel et al., 2011). Total terrestrial water storages (TWS) in large river basins were estimated using the new model by off-line simulation, and compared with the TWS observed by GRACE for 2002-2007. The results showed MAT-HI has an advantage estimating TWS particularly in arid river basins compared with H08 (Hanasaki et al., 2008). MAT-HI was further coupled with a module representing the ground water level fluctuations (Yeh et al., 2005), and consists a new land surface scheme HiGW-MAT (Human Intervention and Ground Water coupled MATSIRO). HiGW-MAT is also associated with a scheme tracing the origin and flow path with the consideration on the sources of water withdrawal from stream flow, medium-size reservoirs and nonrenewable groundwater in addition to precipitation to croplands enabled the assessment of the origin of water producing major crops as Hanasaki et al. (2010). Areas highly dependent on nonrenewable groundwater are detected in the Pakistan, Bangladesh, western part of India, north and western parts of China, some regions in the Arabian Peninsula and the western part of the United States through Mexico. Cumulative nonrenewable groundwater withdrawals estimated by the model are corresponding fairly well with the country statistics of total groundwater withdrawals. Ground water table depletions in large aquifers in US estimated by HiGW-MAT were compared with in-situ observational data, and the correspondences are very good. Mean global exploitation

  7. Renewable energy in Europe

    International Nuclear Information System (INIS)

    Deshaies, M.

    2009-01-01

    Europe's increasing demand for energy and its environmental preoccupations are creating a favourable environment for the development of renewable energy sources. This article stated that although many European countries have adopted voluntary policies since the 1990s to increase the use of renewable energy sources, they have not been developed in an equal or consistent manner. A table was included to show the consumption of renewable energies by country; the percentage of renewable energies in 1995 as compared to 2006; and the consumption of primary energy resources. Combined, Germany, Spain and Denmark produce 75 per cent of wind energy in Europe, while 75 per cent of Europe's hydroelectricity is produced in Norway, Sweden, France, Italy, Austria and Switzerland. Germany has also made significant contributions in developing biomass energy. The article emphasized that the development of renewable energy sources is limited by the fact that it cannot keep up with growing energy demands. In addition, renewable energies cannot yet replace all fossil fuel consumption in Europe because of the variation in development from one country to another. 1 ref., 2 tabs., 4 figs.

  8. CENTRIFUGAL SEPARATORS

    Science.gov (United States)

    Skarstrom, C.

    1959-03-10

    A centrifugal separator is described for separating gaseous mixtures where the temperature gradients both longitudinally and radially of the centrifuge may be controlled effectively to produce a maximum separation of the process gases flowing through. Tbe invention provides for the balancing of increases and decreases in temperature in various zones of the centrifuge chamber as the result of compression and expansions respectively, of process gases and may be employed effectively both to neutralize harmful temperature gradients and to utilize beneficial temperaturc gradients within the centrifuge.

  9. Microparticle Separation by Cyclonic Separation

    Science.gov (United States)

    Karback, Keegan; Leith, Alexander

    2017-11-01

    The ability to separate particles based on their size has wide ranging applications from the industrial to the medical. Currently, cyclonic separators are primarily used in agriculture and manufacturing to syphon out contaminates or products from an air supply. This has led us to believe that cyclonic separation has more applications than the agricultural and industrial. Using the OpenFoam computational package, we were able to determine the flow parameters of a vortex in a cyclonic separator in order to segregate dust particles to a cutoff size of tens of nanometers. To test the model, we constructed an experiment to separate a test dust of various sized particles. We filled a chamber with Arizona test dust and utilized an acoustic suspension technique to segregate particles finer than a coarse cutoff size and introduce them into the cyclonic separation apparatus where they were further separated via a vortex following our computational model. The size of the particles separated from this experiment will be used to further refine our model. Metropolitan State University of Denver, Colorado University of Denver, Dr. Randall Tagg, Dr. Richard Krantz.

  10. 2016 Renewable Energy Data Book

    Energy Technology Data Exchange (ETDEWEB)

    2017-12-29

    The 2016 Renewable Energy Data Book provides facts and figures on energy and electricity use, renewable electricity in the United States, global renewable energy development, wind power, solar power, geothermal power, biopower, hydropower, marine and hydrokinetic power, hydrogen, renewable fuels, and clean energy investment.

  11. 2015 Renewable Energy Data Book

    Energy Technology Data Exchange (ETDEWEB)

    Beiter, Philipp [National Renewable Energy Lab. (NREL), Golden, CO (United States); Tian, Tian [National Renewable Energy Lab. (NREL), Golden, CO (United States)

    2016-11-01

    The Renewable Energy Data Book for 2015 provides facts and figures on energy and electricity use, renewable electricity in the United States, global renewable energy development, wind power, solar power, geothermal power, biopower, hydropower, marine and hydrokinetic power, hydrogen, renewable fuels, and clean energy investment.

  12. 2015 Renewable Energy Data Book

    Energy Technology Data Exchange (ETDEWEB)

    Beiter, Philipp; Tian, Tian

    2016-11-01

    The 2015 Renewable Energy Data Book provides facts and figures on energy and electricity use, renewable electricity in the United States, global renewable energy development, wind power, solar power, geothermal power, biopower, hydropower, marine and hydrokinetic power, hydrogen, renewable fuels, and clean energy investment.

  13. 2014 Renewable Energy Data Book

    Energy Technology Data Exchange (ETDEWEB)

    Beiter, Philipp

    2015-11-01

    The Renewable Energy Data Book for 2014 provides facts and figures on energy and electricity use, renewable electricity in the United States, global renewable energy development, wind power, solar power, geothermal power, biopower, hydropower, marine and hydrokinetic power, hydrogen, renewable fuels, and clean energy investment.

  14. Isotopic separation

    International Nuclear Information System (INIS)

    Castle, P.M.

    1979-01-01

    This invention relates to molecular and atomic isotope separation and is particularly applicable to the separation of 235 U from other uranium isotopes including 238 U. In the method described a desired isotope is separated mechanically from an atomic or molecular beam formed from an isotope mixture utilising the isotropic recoil momenta resulting from selective excitation of the desired isotope species by radiation, followed by ionization or dissociation by radiation or electron attachment. By forming a matrix of UF 6 molecules in HBr molecules so as to collapse the V 3 vibrational mode of the UF 6 molecule the 235 UF 6 molecules are selectively excited to promote reduction of UF 6 molecules containing 235 U and facilitate separation. (UK)

  15. Isotopic separation

    International Nuclear Information System (INIS)

    Chen, C.L.

    1979-01-01

    Isotopic species in an isotopic mixture including a first species having a first isotope and a second species having a second isotope are separated by selectively exciting the first species in preference to the second species and then reacting the selectively excited first species with an additional preselected radiation, an electron or another chemical species so as to form a product having a mass different from the original species and separating the product from the balance of the mixture in a centrifugal separating device such as centrifuge or aerodynamic nozzle. In the centrifuge the isotopic mixture is passed into a rotor where it is irradiated through a window. Heavier and lighter components can be withdrawn. The irradiated mixture experiences a large centrifugal force and is separated in a deflection area into lighter and heavier components. (UK)

  16. Synthesis and characterization of a surface-grafted Cd(II) ion-imprinted polymer for selective separation of Cd(II) ion from aqueous solution

    Energy Technology Data Exchange (ETDEWEB)

    Li, Min [State Key Laboratory of Explosion Science and Technology, Beijing Institute of Technology, Beijing 100081 (China); Feng, Changgen, E-mail: cgfeng@cast.org.cn [State Key Laboratory of Explosion Science and Technology, Beijing Institute of Technology, Beijing 100081 (China); Li, Mingyu; Zeng, Qingxuan; Gan, Qiang [State Key Laboratory of Explosion Science and Technology, Beijing Institute of Technology, Beijing 100081 (China); Yang, Haiyan [Research Institute of Tsinghua University in Shenzhen, Shenzhen 518057 (China)

    2015-03-30

    Highlights: • Cd(II) ion-imprinted polymer (Cd(II)-IIP) is prepared. • Cd(II)-IIP shows high stability, good selectivity and reusability. • Cd(II)-IIP can be used as a sorbent for selective removal of Cd(II) ion. - Abstract: A novel Cd(II) ion-imprinted polymer (Cd(II)-IIP) was prepared with surface imprinting technology by using cadmium chloride as a template and allyl thiourea (ATU) as a functional monomer for on-line solid-phase extraction of trace Cd(II) ion and selective separation Cd(II) ion in water samples. The Cd(II)-IIP exhibited good chemical performance and thermal stability. Kinetics studies showed that the equilibrium adsorption was achieved within 8.0 min and the adsorption process can be described by pseudo-second-order kinetic model. Compared to the Cd(II) non-imprinted polymer (Cd(II)-NIP), the Cd(II)-IIP had a higher adsorption capacity and selectivity for Cd(II) ion. The maximum adsorption capacities of the Cd(II)-IIP and Cd(II)-NIP for Cd(II) were 38.30 and 13.21 mg g{sup −1}, respectively. The relative selectivity coefficients of the adsorbent for Cd(II) in the presence of Cu{sup 2+}, Ni{sup 2+}, Co{sup 2+}, Pb{sup 2+} and Zn{sup 2+} were 2.86, 6.42, 11.50, 9.46 and 3.73, respectively. In addition, the Cd(II) ion adsorbed was easy to remove from sorbent and the Cd(II)-IIP exhibited good stability and reusability. The adsorption capacity had no obvious decrease after being used six times. The accuracy of this method was verified by the standard reference material, it was then applied for cadmium ion determination in different types of water samples.

  17. Separations chemistry

    International Nuclear Information System (INIS)

    Anon.

    1976-01-01

    Results of studies on the photochemistry of aqueous Pu solutions and the stability of iodine in liquid and gaseous CO 2 are reported. Progress is reported in studies on: the preparation of macroporous bodies filled with oxides and sulfides to be used as adsorbents; the beneficiation of photographic wastes; the anion exchange adsorption of transition elements from thiosulfate solutions; advanced filtration applications of energy significance; high-resolution separations; and, the examination of the separation agents, octylphenylphosphoric acid (OPPA) and trihexyl phosphate (THP)

  18. Isotopic separation

    International Nuclear Information System (INIS)

    Chen, C.L.

    1982-01-01

    A method is described for separating isotopes in which photo-excitation of selected isotope species is used together with the reaction of the excited species with postive ions of predetermined ionization energy, other excited species, or free electrons to produce ions or ion fragments of the selected species. Ions and electrons are produced by an electrical discharge, and separation is achieved through radial ambipolar diffusion, electrostatic techniques, or magnetohydrodynamic methods

  19. Influence of drying method on the surface energy of cellulose nanofibrils determined by inverse gas chromatography

    Science.gov (United States)

    Yucheng Peng; Douglas J. Gardner; Yousoo Han; Zhiyong Cai; Mandla A. Tshabalala

    2013-01-01

    Research and development of the renewable nanomaterial cellulose nanofibrils (CNFs) has received considerable attention. The effect of drying on the surface energy of CNFs was investigated. Samples of nanofibrillated cellulose (NFC) and cellulose nanocrystals (CNC) were each subjected to four separate drying methods: air-drying, freeze-drying, spray-drying, and...

  20. Separation techniques: Chromatography

    Science.gov (United States)

    Coskun, Ozlem

    2016-01-01

    Chromatography is an important biophysical technique that enables the separation, identification, and purification of the components of a mixture for qualitative and quantitative analysis. Proteins can be purified based on characteristics such as size and shape, total charge, hydrophobic groups present on the surface, and binding capacity with the stationary phase. Four separation techniques based on molecular characteristics and interaction type use mechanisms of ion exchange, surface adsorption, partition, and size exclusion. Other chromatography techniques are based on the stationary bed, including column, thin layer, and paper chromatography. Column chromatography is one of the most common methods of protein purification. PMID:28058406

  1. Renewable Energy in China

    Directory of Open Access Journals (Sweden)

    Valery I. Salygin

    2015-01-01

    Full Text Available China is the most densely populated country in the world with high rate of economic growth resulting in higher demand for energy resources and in strive to guarantee stable supply of these resources. Chinese annual GDP growth in 2012 and 2013 was down to 7.7% comparing to 10% in 2000-2011 [7]. In 2012 and 2013 economic growth stumbled because of slowdown in manufacturing and exports, taking into account that Chinese government was eager to cut inflation and excessive investments in some segments of the market. Speaking about energy sector Chinese government is aimed at promotion of market-based pricing systems, activities for advanced energy efficiency and higher competition between energy companies, and increased investment in renewable energy resources. Considering renewables as one of many ways to diversify energy supplies, lower dependence on coal and improve environmental situation Chinese government actively supports and develops programs aimed at support of renewable energy industry in China. Chinese economic development is tightly attached to five-year plans. It seems important to mention the fact that main energy goals for current 12-th "five-year plan" are to achieve 15% renewables consumption and CO2 sequestration up to 40-45% by2020 in order to lower dependency on coal and improve environmental situation. As a result of Chinese state policy to develop renewables China achieved certain results in wind energy, helioenergetics, hydroenergetics and energy from waste recycling.

  2. Renewable energy handbook

    Energy Technology Data Exchange (ETDEWEB)

    Fine, R

    1976-01-01

    The potential for renewable energy use in Canada is examined. It is pointed out that Canada can choose to begin to diversify its energy supply now, moving rapidly and smoothly towards an efficient energy society based on renewable energy sources; or, it can continue on its present course and face the possibility of being forced by necessity to make a later transition to renewable sources, probably with a great deal of economic and political disruption. The handbook begins with a discussion on major issues and options available. This second section deals with the technology, applications, and costs of direct solar energy utilization, solar thermal electricity generation, photovoltaic conversion, wind energy, biomass energy, tidal power, wave energy, ocean thermal energy, geothermal energy, heat pumps, and energy storage. Section three discusses how renewable energy might realistically supply Canada's energy requirements within a reasonable period of time. Some issues on how government, industry, and the individual may become involved to make this happen are suggested. A list of resource people and renewable energy businesses is provided in the last section. A recommended reading list and bibliography complete the handbook. (MCW)

  3. Art : accessible, renewable technology

    International Nuclear Information System (INIS)

    Middleton, C.D.

    2004-01-01

    This paper focuses on the role of non-governmental organization (NGO) citizen groups in Ontario in the use and production of electricity. NGOs have the potential to act both directly on their own accord, and indirectly by pressuring government and others. Current demand for electricity is divided between industrial, commercial and residential users. Citizens have an important role to play in reducing energy demand. On the supply side, there is a revival of interest in renewable energy based on wind, photovoltaic and local-hydro technologies as a result of the escalating environmental and economic costs of coal and nuclear generation. However, citizen groups have greater interest and enthusiasm than technical expertise, creating a mismatch between technological solutions and human need or use of them. This paper discusses how this mismatch applies to renewable-energy technologies, many of which are not especially user-friendly, or accessible. While alternative technologies are increasingly welcomed by government, industry is developing a large and growing array of technological devices. In between this is the citizen, who, despite keen interest, can be overwhelmed by the complexity of the situation. This paper links the theoretical perspective to the real world with a discussion of the dynamics between people and renewable energy in citizen groups and makes particular reference to one group, Citizens for Renewable Energy, that has been making renewable energy technology more accessible to its members for over a decade

  4. Subsidies for renewable energy?

    International Nuclear Information System (INIS)

    Skytte, K.; Grenaa Jensen, S.; Morthorst, P.E.; Olsen, O.J.

    2004-01-01

    Ambitious Danish and European energy and environment objectives make a point of using renewable energy sources in the electricity supply. Denmark has been leading country in successful development and commercialization of wind turbines and is as yet one of the leading manufacturers of the world. Danish governments have successfully invested a lot in this development. Other countries have spent more money without achieving a similar success. The questions are why things have gone so well in Denmark and if the Danish success can be repeated for other renewable energy technologies. The starting point of this book is that a political decision on subsidizing the developmental process of a specific technology not in itself guarantees that the technology will turn out reliable and efficient enough to compete successfully in a liberalized electricity market. An understanding of this development is necessary in order to affect a technological development. This book goes through the development of different renewable energy technologies and two theories used for discussing the technological development: experience curves and innovation theory. Based on the discussions and a description of causal relations, an analytical model for different phases of renewable energy technologies' developmental progress and technological life cycle is made. The model is used for evaluating the subsidies for chosen renewable technologies in Denmark. With wind energy as example an analysis of what went well or badly, what might be done and which actions might be efficient is made. (BA)

  5. Separable algebras

    CERN Document Server

    Ford, Timothy J

    2017-01-01

    This book presents a comprehensive introduction to the theory of separable algebras over commutative rings. After a thorough introduction to the general theory, the fundamental roles played by separable algebras are explored. For example, Azumaya algebras, the henselization of local rings, and Galois theory are rigorously introduced and treated. Interwoven throughout these applications is the important notion of étale algebras. Essential connections are drawn between the theory of separable algebras and Morita theory, the theory of faithfully flat descent, cohomology, derivations, differentials, reflexive lattices, maximal orders, and class groups. The text is accessible to graduate students who have finished a first course in algebra, and it includes necessary foundational material, useful exercises, and many nontrivial examples.

  6. EDITORIAL: Renewing energy technology Renewing energy technology

    Science.gov (United States)

    Demming, Anna

    2011-06-01

    Renewable energy is now a mainstream concern among businesses and governments across the world, and could be considered a characteristic preoccupation of our time. It is interesting to note that many of the energy technologies currently being developed date back to very different eras, and even predate the industrial revolution. The fuel cell was first invented as long ago as 1838 by the Swiss--German chemist Christian Friedrich Schönbein [1], and the idea of harnessing solar power dates back to ancient Greece [2]. The enduring fascination with new means of harnessing energy is no doubt linked to man's innate delight in expending it, whether it be to satisfy the drive of curiosity, or from a hunger for entertainment, or to power automated labour-saving devices. But this must be galvanized by the sustained ability to improve device performance, unearthing original science, and asking new questions, for example regarding the durability of photovoltaic devices [3]. As in so many fields, advances in hydrogen storage technology for fuel cells have benefited significantly from nanotechnology. The idea is that the kinetics of hydrogen uptake and release may be reduced by decreasing the particle size. An understanding of how effective this may be has been hampered by limited knowledge of the way the thermodynamics are affected by atom or molecule cluster size. Detailed calculations of individual atoms in clusters are limited by computational resources as to the number of atoms that can studied, and other innovative approaches that deal with force fields derived by extrapolating the difference between the properties of clusters and bulk matter require labour-intensive modifications when extending such studies to new materials. In [4], researchers in the US use an alternative approach, considering the nanoparticle as having the same crystal structure as the bulk but relaxing the few layers of atoms near the surface. The favourable features of nanostructures for catalysis

  7. Isotope separation

    International Nuclear Information System (INIS)

    Bartlett, R.J.; Morrey, J.R.

    1978-01-01

    A method and apparatus is described for separating gas molecules containing one isotope of an element from gas molecules containing other isotopes of the same element in which all of the molecules of the gas are at the same electronic state in their ground state. Gas molecules in a gas stream containing one of the isotopes are selectively excited to a different electronic state while leaving the other gas molecules in their original ground state. Gas molecules containing one of the isotopes are then deflected from the other gas molecules in the stream and thus physically separated

  8. Renewability of geothermal resources

    Energy Technology Data Exchange (ETDEWEB)

    O' Sullivan, Michael; Yeh, Angus [Department of Engineering Science, University of Auckland, Auckland (New Zealand); Mannington, Warren [Contact Energy Limited, Taupo (New Zealand)

    2010-12-15

    In almost all geothermal projects worldwide, the rate of extraction of heat energy exceeds the pre-exploitation rate of heat flow from depth. For example, current production of geothermal heat from the Wairakei-Tauhara system exceeds the natural recharge of heat by a factor of 4.75. Thus, the current rate of heat extraction from Wairakei-Tauhara is not sustainable on a continuous basis, and the same statement applies to most other geothermal projects. Nevertheless, geothermal energy resources are renewable in the long-term because they would fully recover to their pre-exploitation state after an extended shut-down period. The present paper considers the general issue of the renewability of geothermal resources and uses computer modeling to investigate the renewability of the Wairakei-Tauhara system. In particular, modeling is used to simulate the recovery of Wairakei-Tauhara after it is shut down in 2053 after a hundred years of production. (author)

  9. People and renewable energy

    International Nuclear Information System (INIS)

    Rosenvald, Avo

    2002-01-01

    The use of renewable energy is tightly connected to solving social problems in Estonia by creating more new jobs. It is essential that Estonia should increase the use of biofuels. One of the biofuels, firewood, has been used already for centuries. For wider use of renewable energy in Estonia, it is not enough to rely only on enterprices. Rather, before any serious progress can take place, the state should create the appropriate legal environment. Due to its many social and environmental aspects, renewable energy is more important to the state than a sole enterprice. Unfortunately, Estonian government has been delaying its duties. Estonia has two resources that should be taken advantage of, fertile spare land and people still used to the country life. The country people would get work by growing different energy crops on the spare land. (author)

  10. Understanding renewable energy systems

    Energy Technology Data Exchange (ETDEWEB)

    Quaschning, Volker

    2005-01-15

    Beginning with an overview of renewable energy sources including biomass, hydroelectricity, geothermal, tidal, wind and solar power, this book explores the fundamentals of different renewable energy systems. The main focus is on technologies with high development potential such as solar thermal systems, photovoltaics and wind power. This text not only describes technological aspects, but also deals consciously with problems of the energy industry. In this way, the topics are treated in a holistic manner, bringing together maths, engineering, climate studies and economics, and enabling readers to gain a broad understanding of renewable energy technologies and their potential. The book also contains a free CD-ROM resource, which includes a variety of specialist simulation software and detailed figures from the book. (Author)

  11. Renewables vs fossil fuels

    Energy Technology Data Exchange (ETDEWEB)

    Adams, K. (Energy Research and Development Corporation (Australia))

    1992-01-01

    The paper examines some of the factors which will influence the future mix of energy from fossil fuels and renewable sources in Australia. Aspects covered include: the present energy situation; impact of environmental issues; potential for renewable energy; motivators for change; and research and development. It is concluded that the future for fossil fuels and renewable energy is dependent on a number of complex factors, many of which are currently unknown. The key factor is economic viability and that will be influenced by a range of factors such as policies of the Australian and overseas governments in relation to pollution and environment protection (reflected in the cost of meeting such requirements), exploration and production costs (also influenced by government policies), availability of supply, rate of technological development and the size of export markets. 8 refs., 2 figs., 1 tab.

  12. Raw and renewable polymers

    CSIR Research Space (South Africa)

    Joseph, S

    2010-01-01

    Full Text Available in the permeability of the membrane and HO H3C H3C H2C H2C HO OH NH NH OH O OC C n O O O O Fig. 4 Structure of Chitin Raw and Renewable Polymers promoting internal osmotic imbalances. This results in leaching of electrolytes and proteins. 2... is often lost. In most cases this denaturation is not reversible. R-CH-COOH NH2 w Amino acid H2N COOHR a Amino acid Fig. 5 Structure of amino acid Raw and Renewable Polymers The solubilities of proteins vary considerably based on compositions...

  13. Renewable energy sources (promotion)

    International Nuclear Information System (INIS)

    Cook, F.

    1986-01-01

    Permission to present a Bill to establish an independent commission directly responsible for the research, development and demonstration of clean, renewable, alternative sources of energy (to nuclear energy) is requested. The paragraphs of the preamble to the Bill are summarized by the Member seeking permission. The main reason for promoting renewable energy sources is opposition to the nuclear industry. One objection was raised. However, permission was granted to present the Bill and it was read for the first time with a second reading ordered for 7 March 1986. The Bill itself is not reprinted but the permission and question are reported verbatim. (U.K.)

  14. Renewable Electricity Futures (Presentation)

    Energy Technology Data Exchange (ETDEWEB)

    Mai, T.

    2012-08-01

    This presentation library summarizes findings of NREL's Renewable Electricity Futures study, published in June 2012. RE Futures investigated the challenges and impacts of achieving very high renewable electricity generation levels in the contiguous United States by 2050. It was presented at the 2012 RE AMP Annual Meeting. RE-AMP is an active network of 144 nonprofits and foundations across eight Midwestern states working on climate change and energy policy with the goal of reducing global warming pollution economy-wide 80% by 2050.

  15. Fundamentals of affinity cell separations.

    Science.gov (United States)

    Zhang, Ye; Lyons, Veronica; Pappas, Dimitri

    2018-03-01

    Cell separations using affinity methods continue to be an enabling science for a wide variety of applications. In this review, we discuss the fundamental aspects of affinity separation, including the competing forces for cell capture and elution, cell-surface interactions, and models for cell adhesion. Factors affecting separation performance such as bond affinity, contact area, and temperature are presented. We also discuss and demonstrate the effects of nonspecific binding on separation performance. Metrics for evaluating cell separations are presented, along with methods of comparing separation techniques for cell isolation using affinity capture. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  16. Superhydrophobic Cu{sub 2}S@Cu{sub 2}O film on copper surface fabricated by a facile chemical bath deposition method and its application in oil-water separation

    Energy Technology Data Exchange (ETDEWEB)

    Pi, Pihui, E-mail: phpi@scut.edu.cn; Hou, Kun; Zhou, Cailong; Li, Guidong; Wen, Xiufang; Xu, Shouping; Cheng, Jiang; Wang, Shuangfeng

    2017-02-28

    Highlights: • A superhydrophobic film with macro/nano structure was fabricated on copper surface. • The as-prepared film shows outstanding water repellency and long-term storage stability. • The same method was used to fabricate superhydrophobic/superoleophilic copper mesh. • The obtained mesh could realize separation of various oily sewages with separation efficiency above 94%. - Abstract: Cu{sub 2}S and Cu{sub 2}O composite (Cu{sub 2}S@Cu{sub 2}O) film with micro/nano binary structure was created on copper surface using the mixing solution of sodium thiosulphate and copper sulfate by a facile chemical bath deposition method. After modification with low-cost polydimethylsioxane (PDMS), the superhydrophobic Cu{sub 2}S@Cu{sub 2}O film was obtained. The as-prepared film shows outstanding water repellency with a water contact angle larger than 150° and long-term storage stability. The geometric morphology and chemical composition of the film were characterized by scanning electron microscope (SEM), energy dispersive spectrometer (EDS) and attenuated total reflectance Fourier transform infrared spectroscopy (ATR-FTIR), respectively. Moreover, the same method was used to fabricate superhydrophobic/superoleophilic copper mesh, and it could realize separation of various oily sewages with separation efficiency above 94%. This strategy has potential to fabricate the practical superhydrophobic Cu{sub 2}S@Cu{sub 2}O film on copper surface on a large scale due to its simplicity and low cost.

  17. DRI Renewable Energy Center (REC) (NV)

    Energy Technology Data Exchange (ETDEWEB)

    Hoekman, S. Kent; Broch, Broch; Robbins, Curtis; Jacobson, Roger; Turner, Robert

    2012-12-31

    The primary objective of this project was to utilize a flexible, energy-efficient facility, called the DRI Renewable Energy Experimental Facility (REEF) to support various renewable energy research and development (R&D) efforts, along with education and outreach activities. The REEF itself consists of two separate buildings: (1) a 1200-ft2 off-grid capable house and (2) a 600-ft2 workshop/garage to support larger-scale experimental work. Numerous enhancements were made to DRI's existing renewable power generation systems, and several additional components were incorporated to support operation of the REEF House. The power demands of this house are satisfied by integrating and controlling PV arrays, solar thermal systems, wind turbines, an electrolyzer for renewable hydrogen production, a gaseous-fuel internal combustion engine/generator set, and other components. Cooling needs of the REEF House are satisfied by an absorption chiller, driven by solar thermal collectors. The REEF Workshop includes a unique, solar air collector system that is integrated into the roof structure. This system provides space heating inside the Workshop, as well as a hot water supply. The Workshop houses a custom-designed process development unit (PDU) that is used to convert woody biomass into a friable, hydrophobic char that has physical and chemical properties similar to low grade coal. Besides providing sufficient space for operation of this PDU, the REEF Workshop supplies hot water that is used in the biomass treatment process. The DRI-REEF serves as a working laboratory for evaluating and optimizing the performance of renewable energy components within an integrated, residential-like setting. The modular nature of the system allows for exploring alternative configurations and control strategies. This experimental test bed is also highly valuable as an education and outreach tool both in providing an infrastructure for student research projects, and in highlighting renewable

  18. Sustainable processes synthesis for renewable resources

    International Nuclear Information System (INIS)

    Halasz, L.; Povoden, G.; Narodoslawsky, M.

    2005-01-01

    Renewable resources pose special challenges to process synthesis. Due to decentral raw material generation, usually low transport densities and the perishable character of most renewable raw materials in combination with their time dependent availability, logistical questions as well as adaptation to regional agricultural structures are necessary. This calls for synthesis of structures not only of single processes but of the whole value chain attached to the utilisation of a certain resource. As most of the innovative technologies proposed to build on a renewable raw material base face stiff economic competition from fossil based processes, economic optimality of the value chain is crucial to their implementation. On top of this widening of the process definition for synthesis, many processes on the base of renewable resources apply technologies (like membrane separations, chromatographic purification steps, etc.) for which the heuristic knowledge is still slim. This reduces the choice of methods for process synthesis, mainly to methods based on combinatorial principles. The paper investigates applicability as well as impact on technology development of process synthesis for renewable raw material utilisation. It takes logistic considerations into account and applies process synthesis to the case study of the green biorefinery concept. The results show the great potential of process synthesis for technology development of renewable resource utilisation. Applied early in the development phase, it can point towards the most promising utilisation pathways, thus guiding the engineering work. On top of that, and even more important, it can help avoid costly development flops as it also clearly indicates 'blind alleys' that have to be avoided

  19. Nontraditional renewable energy sources

    International Nuclear Information System (INIS)

    Shpil'rajn, Eh.Eh.

    1997-01-01

    The paper considers the application possibilities of nontraditional renewable energy sources to generate electricity, estimates the potential of nontraditional sources using energy of Sun, wind, biomass, as well as, geothermal energy and presents the results of economical analysis of cost of electricity generated by solar electrical power plants, geothermal and electrical plants and facilities for power reprocessing of biomass. 1 tab

  20. The wood, renewable energy

    International Nuclear Information System (INIS)

    Acket, C.

    2006-12-01

    This document evaluates the french forest situation and its future. Indeed, the wood energy constitutes in France the first renewable energy after the hydraulic. It presents the today situation of the french forest providing statistical data, evaluation of the energy estimation, the carbon fixation, the resources, the perspectives wood energy for 2050, the biofuels and an economic analysis. (A.L.B.)

  1. Information for Institutional Renewal.

    Science.gov (United States)

    Spencer, Richard L.

    1979-01-01

    Discusses a planning, management, and evaluation system, an objective-based planning process, research databases, analytical reports, and transactional data as state-of-the-art tools available to generate data which link research directly to planning for institutional renewal. (RC)

  2. Renewable Energies, Present & Future

    Institute of Scientific and Technical Information of China (English)

    X. S. Cai

    2005-01-01

    Fossil fuels are major cause of environmental destruction in pollutions. It has created much needed momentum for renewable energies, which are environmentally benign, generated locally, and can play a significant role in developing economy. As a sustainable energy sources, it can grow at a rapid pace to meet increasing demands for electricity in a cost-effective way.

  3. Renewable Energy for Microenterprise

    Energy Technology Data Exchange (ETDEWEB)

    Allderdice, A.; Rogers, J.H.

    2000-11-28

    This guide provides readers with a broad understanding of the potential benefits that current renewable energy technologies can offer rural microenterprises. It also introduces the institutional approaches that have been developed to make RE technologies accessible to microentrepreneurs and the challenges that these entrepreneurs have encountered.

  4. Renewable material resource potential

    NARCIS (Netherlands)

    van Weenen, H.; Wever, R.; Quist, J.; Tukker, A.; Woudstra, J.; Boons, F.A.A.; Beute, N.

    2010-01-01

    Renewable material resources, consist of complex systems and parts. Their sub-systems and sub-sub-systems, have unique, specific, general and common properties. The character of the use that is made of these resources, depends on the availability of knowledge, experience, methods, tools, machines

  5. Renewable Energy Essentials: Hydropower

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2010-07-01

    Hydropower is currently the most common form of renewable energy and plays an important part in global power generation. Worldwide hydropower produced 3 288 TWh, just over 16% of global electricity production in 2008, and the overall technical potential for hydropower is estimated to be more than 16 400 TWh/yr.

  6. Renewable Substitutability Index: Maximizing Renewable Resource Use in Buildings

    Directory of Open Access Journals (Sweden)

    Ravi S. Srinivasan

    2015-05-01

    Full Text Available In order to achieve a material and energy balance in buildings that is sustainable in the long run, there is an urgent need to assess the renewable and non-renewable resources used in the manufacturing process and to progressively replace non-renewable resources with renewables. Such progressive disinvestment in the non-renewable resources that may be substituted with renewable resources is referred to as “Renewable Substitutability” and if implemented, this process will lead to a paradigm shift in the way building materials are manufactured. This paper discusses the development of a Renewable Substitutability Index (RSI that is designed to maximize the use of renewable resources in a building and quantifies the substitution process using solar emergy (i.e., the solar equivalent joules required for any item. The RSI of a building or a building component, i.e., floor or wall systems, etc., is the ratio of the renewable resources used during construction, including replacement and maintenance, to the building’s maximum renewable emergy potential. RSI values range between 0 and 1.0. A higher RSI achieves a low-energy building strategy promoting a higher order of sustainability by optimizing the use of renewables over a building’s lifetime from formation-extraction-manufacturing to maintenance, operation, demolition, and recycle.

  7. The Renewable Energy Data Explorer: Mapping Our Renewable Energy Future

    Energy Technology Data Exchange (ETDEWEB)

    2017-04-13

    The Renewable Energy (RE) Data Explorer, developed by the National Renewable Energy Laboratory, is an innovative web-based platform that allows users to visualize and analyze renewable energy potential. The RE Data Explorer informs prospecting, integrated planning, and policymaking to enable low emission development.

  8. Implementation of renewable energy in the European Union until 2010

    Energy Technology Data Exchange (ETDEWEB)

    Harmelink, M.; Voogt, M.; Joosen, S.; De Jager, D. [Ecofys, Utrecht (Netherlands); Palmers, G.; Shaw, S. [3E, Brussels (Belgium); Cremer, C. [Fraunhofer-Institut fuer Systemtechnik und Innovationsforschung ISI, Karlsruhe (Germany)

    2002-08-01

    PRETIR is the acronym for Progress of Renewable Energy: Target Setting, Implementation and Realisation. The PRETIR project aims at developing a monitoring protocol, including a set of transparent indicators, through which monitoring of policy development with regard to renewable energy sources in the 15 European Union (EU) Member States can take place; i.e. the degree to which the national and European targets are translated to national action plans and policy instruments to realise the targeted implementation of renewable energy sources. By analysing the results of this monitoring process conclusions can be drawn on the likeliness of achieving the goals as set in the White Paper, the Directive on electricity from renewable energy sources, the draft Directive on biofuels and the Campaign for Take-Off. This report holds the results of the monitoring of renewable energy policies for the European Union. Chapters 2 and 3 start with a brief outline of the used definitions and monitoring methodology. A more detailed description of the methodology is available in the monitoring report, published separately. Chapter 4 provides an overview of the renewable energy policies in the EU Member States and is followed by chapters dealing with each of the distinguished renewable energy sources. Finally, chapter 11 holds the conclusions on the progress on implementation of renewable energy sources in the European Union.

  9. Renewable Energy on Tribal Lands

    Science.gov (United States)

    This page contains presentations from the Brown to Green: Make the Connection to Renewable Energy workshop held in Santa Fe, New Mexico, during December 10-11, 2008 regarding Renewable Energy on Tribal Lands.

  10. Non-renewal of contracts

    CERN Multimedia

    Association du personnel

    2007-01-01

    A new illegal practice is appearing in certain sectors of the Organization: the non-renewal of renewable three-year limited-duration (LD) contracts, despite a more than satisfactory performance and an obvious commitment to the Organization.

  11. Status and Trends in U.S. Compliance and Voluntary Renewable Energy Certificate Markets (2010 Data)

    Energy Technology Data Exchange (ETDEWEB)

    Heeter, Jenny [National Renewable Energy Lab. (NREL), Golden, CO (United States); Bird, Lori [National Renewable Energy Lab. (NREL), Golden, CO (United States)

    2011-10-01

    The "voluntary" or "green power" market is that in which consumers and institutions voluntarily purchase renewable energy to match all or part of their electricity needs. Voluntary action provides a revenue stream for renewable energy projects and raises consumer awareness of the benefits of renewable energy. There are numerous ways consumers and institutions can purchase renewable energy. Historically, the voluntary market has consisted of three market sectors: (1) utility green pricing programs (in states with regulated electricity markets), (2) competitive suppliers (in states with restructured electricity markets), and (3) unbundled renewable electricity certificate (REC) markets, where RECs are purchased by consumers separately from electricity ("unbundled").

  12. Separators - Technology review: Ceramic based separators for secondary batteries

    Energy Technology Data Exchange (ETDEWEB)

    Nestler, Tina; Schmid, Robert; Münchgesang, Wolfram; Bazhenov, Vasilii; Meyer, Dirk C. [Technische Universität Bergakademie Freiberg, Institut für Experimentelle Physik, Leipziger Str. 23, 09596 Freiberg (Germany); Schilm, Jochen [Fraunhofer-Institut für Keramische Technologien und Systeme IKTS, Winterbergstraße 28, 01277 Dresden (Germany); Leisegang, Tilmann [Fraunhofer-Technologiezentrum Halbleitermaterialien THM, Am St.-Niclas-Schacht 13, 09599 Freiberg (Germany)

    2014-06-16

    Besides a continuous increase of the worldwide use of electricity, the electric energy storage technology market is a growing sector. At the latest since the German energy transition ('Energiewende') was announced, technological solutions for the storage of renewable energy have been intensively studied. Storage technologies in various forms are commercially available. A widespread technology is the electrochemical cell. Here the cost per kWh, e. g. determined by energy density, production process and cycle life, is of main interest. Commonly, an electrochemical cell consists of an anode and a cathode that are separated by an ion permeable or ion conductive membrane - the separator - as one of the main components. Many applications use polymeric separators whose pores are filled with liquid electrolyte, providing high power densities. However, problems arise from different failure mechanisms during cell operation, which can affect the integrity and functionality of these separators. In the case of excessive heating or mechanical damage, the polymeric separators become an incalculable security risk. Furthermore, the growth of metallic dendrites between the electrodes leads to unwanted short circuits. In order to minimize these risks, temperature stable and non-flammable ceramic particles can be added, forming so-called composite separators. Full ceramic separators, in turn, are currently commercially used only for high-temperature operation systems, due to their comparably low ion conductivity at room temperature. However, as security and lifetime demands increase, these materials turn into focus also for future room temperature applications. Hence, growing research effort is being spent on the improvement of the ion conductivity of these ceramic solid electrolyte materials, acting as separator and electrolyte at the same time. Starting with a short overview of available separator technologies and the separator market, this review focuses on ceramic

  13. Separators - Technology review: Ceramic based separators for secondary batteries

    Science.gov (United States)

    Nestler, Tina; Schmid, Robert; Münchgesang, Wolfram; Bazhenov, Vasilii; Schilm, Jochen; Leisegang, Tilmann; Meyer, Dirk C.

    2014-06-01

    Besides a continuous increase of the worldwide use of electricity, the electric energy storage technology market is a growing sector. At the latest since the German energy transition ("Energiewende") was announced, technological solutions for the storage of renewable energy have been intensively studied. Storage technologies in various forms are commercially available. A widespread technology is the electrochemical cell. Here the cost per kWh, e. g. determined by energy density, production process and cycle life, is of main interest. Commonly, an electrochemical cell consists of an anode and a cathode that are separated by an ion permeable or ion conductive membrane - the separator - as one of the main components. Many applications use polymeric separators whose pores are filled with liquid electrolyte, providing high power densities. However, problems arise from different failure mechanisms during cell operation, which can affect the integrity and functionality of these separators. In the case of excessive heating or mechanical damage, the polymeric separators become an incalculable security risk. Furthermore, the growth of metallic dendrites between the electrodes leads to unwanted short circuits. In order to minimize these risks, temperature stable and non-flammable ceramic particles can be added, forming so-called composite separators. Full ceramic separators, in turn, are currently commercially used only for high-temperature operation systems, due to their comparably low ion conductivity at room temperature. However, as security and lifetime demands increase, these materials turn into focus also for future room temperature applications. Hence, growing research effort is being spent on the improvement of the ion conductivity of these ceramic solid electrolyte materials, acting as separator and electrolyte at the same time. Starting with a short overview of available separator technologies and the separator market, this review focuses on ceramic-based separators

  14. Autonomous renewable energy conversion system

    Energy Technology Data Exchange (ETDEWEB)

    Valtchev, V. [Technical University of Varna (Bulgaria). Dept. of Electronics; Bossche, A. van den; Ghijselen, J.; Melkebeek, J. [University of Gent (Belgium). Dept. of Electrical Power Engineering

    2000-02-01

    This paper briefly reviews the need for renewable power generation and describes a medium-power Autonomous Renewable Energy Conversion System (ARECS), integrating conversion of wind and solar energy sources. The objectives of the paper are to extract maximum power from the proposed wind energy conversion scheme and to transfer this power and the power derived by the photovoltaic system in a high efficiency way to a local isolated load. The wind energy conversion operates at variable shaft speed yielding an improved annual energy production over constant speed systems. An induction generator (IG) has been used because of its reduced cost, robustness, absence of separate DC source for excitation, easier dismounting and maintenance. The maximum energy transfer of the wind energy is assured by a simple and reliable control strategy adjusting the stator frequency of the IG so that the power drawn is equal to the peak power production of the wind turbine at any wind speed. The presented control strategy also provides an optimal efficiency operation of the IG by applying a quadratic dependence between the IG terminal voltage and frequency V {approx} f{sup 2}. For improving the total system efficiency, high efficiency converters have been designed and implemented. The modular principle of the proposed DC/DC conversion provides the possibility for modifying the system structure depending on different conditions. The configuration of the presented ARECS and the implementation of the proposed control algorithm for optimal power transfer are fully discussed. The stability and dynamic performance as well as the different operation modes of the proposed control and the operation of the converters are illustrated and verified on an experimental prototype. (author)

  15. Isotope separation

    International Nuclear Information System (INIS)

    Rosevear, A.; Sims, H.E.

    1985-01-01

    sup(195m)Au for medical usage is separated from sup(195m)Hg in a solution containing ions of sup(195m)Hg by contacting the solution with an adsorbing agent to adsorb 195 Hgsup(H) thereon, followed by selective elution of sup(195m)Au generated by radioactive decay of the sup(195m)Hg. The adsorbing agent comprises a composite material in the form of an inert porous inorganic substrate (e.g. Kieselguhr),the pores of which are occupied by a hydrogel of a polysaccharide (e.g. agarose) carrying terminal thiol groups for binding Hgsup(H) ions. (author)

  16. Seeing Beyond the Painting Surface with Terahertz Time-Domain Imaging (THz-TDI): a signal separation method for extracting images of buried individual layers in paintings

    DEFF Research Database (Denmark)

    Filtenborg, Troels Folke; Skou-Hansen, Jakob; Koch Dandolo, Corinna Ludovica

    2015-01-01

    and denoising methods used to resolve temporal features of THz reflected signals, they result impractical if applied to large images analysis. Therefore, we presented a simple, fast and effective method to separate single THz pulses of interest from the entire signal recorded at each spatial coordinate...

  17. A NEW QUATERNARY MOBILE PHASE SYSTEM FOR OPTIMIZATION OF TLC SEPARATIONS OF ALKALOIDS USING MIXTURE DESIGNS AND RESPONSE-SURFACE MODELING

    NARCIS (Netherlands)

    COENEGRACHT, PMJ; DIJKMAN, M; DUINEVELD, CAA; METTING, HJ; ELEMA, ET; MALINGRE, TM

    1991-01-01

    A new combination of four organic solvents is proposed for the optimization of TLC separations of basic drugs and alkaloids. The solvents are diethylamine (DEA), methanol (MeOH), chloroform (CHCl3) and ethylacetate (EtAc). They were selected from a collection of ten solvents used in Normal Phase TLC

  18. RENEWABLE ENERGY IN TOURISM

    Directory of Open Access Journals (Sweden)

    MĂDĂLINA MIHĂILĂ

    2012-06-01

    Full Text Available Recent reports published by the International Energy Agency and U.S. Department of Energy, regarding the global energy outlook for the first three decades of the XXI century, warns of global trends on energy demand, increasing dependence on energy imports, coal use and volume emissions of greenhouse gases, torism industry being one of the biggest energy consumption industry. Uncertainties on different models of regional development and access of the world to traditional energy resources require a change of orientation towards long-term scenarios for assessing energy domain, increasing the share of energy from renewable resources beeing one of the solutions. Intourism the renewable energy is a solution for a positive impact on enviroment , reduced operational costs and even won an extra-profit.

  19. Renewables in Electricity Markets

    DEFF Research Database (Denmark)

    Ordoudis, Christos; Papakonstantinou, Athanasios; Pinson, Pierre

    2014-01-01

    Electricity is nowadays commonly exchanged through electricity markets, designed in a context where dispatchable generators, with non-negligible marginal costs, were dominating. By depending primarily on conventional (fossil, hydro and nuclear) power generation based on marginal pricing...... not designed to take into account the uncertainty brought by the substantial variability and limited predictability associated with stochastic sources, most notably wind power and solar energy. Due to these developments, the need for decision making models able to account for the uncertainty introduced by high...... from renewables, and on the adaption of electricity market designs and power system operations to the aforementioned characteristics of renewables. Additionally, the aim of the research group is supplemented by providing the appropriate frameworks for secure future investments in the field...

  20. Renewable Energy Systems

    DEFF Research Database (Denmark)

    Lund, Henrik; Mathiesen, Brian Vad; Connolly, David

    2014-01-01

    on the electricity sector, smart energy systems include the entire energy system in its approach to identifying suitable energy infrastructure designs and operation strategies. The typical smart grid sole focus on the electricity sector often leads to the conclusion that transmission lines, flexible electricity......This paper presents the learning of a series of studies that analyse the problems and perspectives of converting the present energy system into a 100 % renewable energy system using a smart energy systems approach. As opposed to, for instance, the smart grid concept, which takes a sole focus...... are to be found when the electricity sector is combined with the heating and cooling sectors and/or the transportation sector. Moreover, the combination of electricity and gas infrastructures may play an important role in the design of future renewable energy systems. The paper illustrates why electricity smart...

  1. Bolivia renewable energy development

    Energy Technology Data Exchange (ETDEWEB)

    Smith, P.

    1997-12-01

    The author summarizes changes which have occurred in Bolivia in the past year which have had an impact on renewable energy source development. Political changes have included the privatization of power generation and power distribution, and resulted in a new role for state level government and participation by the individual. A National Rural Electrification Plan was adopted in 1996, which stresses the use of GIS analysis and emphasizes factors such as off grid, economic index, population density, maintenance risk, and local organizational structure. The USAID program has chosen to stress economic development, environmental programs, and health over village power programs. The national renewables program has adopted a new development direction, with state projects, geothermal projects, and private sector involvement stressed.

  2. Renewable Energy Symposium

    International Nuclear Information System (INIS)

    2016-01-01

    Representatives of state universities, public institutions and Costa Rican private sector, and American experts have exposed projects or experiences about the use and generation of renewable energy in different fields. The thematics presented have been about: development of smart grids and design of electrical energy production systems that allow money saving and reducing emissions to the environment; studies on the use of non-traditional plants and agricultural waste; sustainable energy model in the process of coffee production; experiments from biomass for the fabrication of biodiesel, biogas production and storage; and the use of non-conventional energy. Researches were presented at the Renewable Energy Symposium, organized by the Centro de Investigacion en Estructuras Microscopicas and support of the Vicerrectoria de Investigacion, both from the Universidad de Costa Rica [es

  3. Renewable energy project development

    Energy Technology Data Exchange (ETDEWEB)

    Ohi, J.

    1996-12-31

    The author presents this paper with three main thrusts. The first is to discuss the implementation of renewable energy options in China, the second is to identify the key project development steps necessary to implement such programs, and finally is to develop recommendations in the form of key issues which must be addressed in developing such a program, and key technical assistance needs which must be addressed to make such a program practical.

  4. Renewing Samsø

    DEFF Research Database (Denmark)

    Papazu, Irina

    2017-01-01

    and globally, I ask: if indeed such a process of renewal must be understood as a political process and the island’s energy transition as an inherently political event, what can Samsø teach us about the workings of politics and local democracy as enacted in practice? This is politics not as election result...... or ideological struggle over values, ideals and the distribution of goods, but as the down-to-earth but significant activity of creating something new together....

  5. Self-renewal molecular mechanisms of colorectal cancer stem cells.

    Science.gov (United States)

    Pan, Tianhui; Xu, Jinghong; Zhu, Yongliang

    2017-01-01

    Colorectal cancer stem cells (CCSCs) represent a small fraction of the colorectal cancer cell population that possess self-renewal and multi-lineage differentiation potential and drive tumorigenicity. Self-renewal is essential for the malignant biological behaviors of colorectal cancer stem cells. While the self-renewal molecular mechanisms of colorectal cancer stem cells are not yet fully understood, the aberrant activation of signaling pathways, such as Wnt, Notch, transforming growth factor-β (TGF-β)/bone morphogenetic protein (BMP) and Hedgehog-Gli (HH-GLI), specific roles mediated by cell surface markers and micro-environmental factors are involved in the regulation of self-renewal. The elucidation of the molecular mechanisms behind self-renewal may lead to the development of novel targeted interventions for the treatment of colorectal cancer.

  6. Renewable Energy in Latvia

    Energy Technology Data Exchange (ETDEWEB)

    Shipkovs, P.; Kashkarova, G. [Latvian Energy Agency, Riga (Latvia); Shipkovs, M. [Energy-R Ltd., Riga (Latvia)

    1997-12-31

    Latvia is among those countries that do not have gas, coal and, for the time being, also oil resources of its own. The amount of power produced in Latvia does not meet the demand, consequently a part of the power has to be purchased from neighbouring countries. Firewood, peat and hydro resources are the only significant domestic energy resources. Massive decrease of energy consumption has been observed since Latvia regained independence. Domestic and renewable energy resources have been examined and estimated. There are already 13 modern boiler houses operating in Latvia with total installed capacity 45 MW that are fired with wood chips. Latvian companies are involved in the production of equipment. 7 small HPPs have been renewed with the installed capacity 1.85 MW. Wind plant in Ainazi has started its operation, where two modern wind turbines with the capacity of 0.6 MW each have been installed. Mechanism of tariff setting is aligned. Favourable power energy purchasing prices are set for renewable energy sources and small cogeneration plants

  7. Market analysis. Renewable fuels

    International Nuclear Information System (INIS)

    2014-01-01

    The Agency for Renewable Resources (FNR) had on behalf of the Federal Ministry of Food and Agriculture created a study on the market development of renewable resources in Germany and published this in the year of 2006. The aim of that study was to identify of actual status and market performance of the individual market segments of the material and energetic use as a basis for policy recommendations for accelerated and long term successful market launch and market share expansion of renewable raw materials. On behalf of the FNR, a market analysis of mid-2011 was carried out until the beginning of 2013, the results of which are hereby resubmitted. This market analysis covers all markets of material and energetic use in the global context, taking account of possible competing uses. A market segmentation, which was based on the product classification of the Federal Statistical Office, formed the basis of the analysis. A total of ten markets have been defined, seven material and three energetic use. [de

  8. Renewable Energy in Latvia

    Energy Technology Data Exchange (ETDEWEB)

    Shipkovs, P; Kashkarova, G [Latvian Energy Agency, Riga (Latvia); Shipkovs, M [Energy-R Ltd., Riga (Latvia)

    1998-12-31

    Latvia is among those countries that do not have gas, coal and, for the time being, also oil resources of its own. The amount of power produced in Latvia does not meet the demand, consequently a part of the power has to be purchased from neighbouring countries. Firewood, peat and hydro resources are the only significant domestic energy resources. Massive decrease of energy consumption has been observed since Latvia regained independence. Domestic and renewable energy resources have been examined and estimated. There are already 13 modern boiler houses operating in Latvia with total installed capacity 45 MW that are fired with wood chips. Latvian companies are involved in the production of equipment. 7 small HPPs have been renewed with the installed capacity 1.85 MW. Wind plant in Ainazi has started its operation, where two modern wind turbines with the capacity of 0.6 MW each have been installed. Mechanism of tariff setting is aligned. Favourable power energy purchasing prices are set for renewable energy sources and small cogeneration plants

  9. What drives renewable energy development?

    International Nuclear Information System (INIS)

    Alagappan, L.; Orans, R.; Woo, C.K.

    2011-01-01

    This viewpoint reviews renewable energy development in 14 markets that differ in market structure (restructured vs. not restructured), use of feed-in-tariff (FIT) (yes vs. no), transmission planning (anticipatory vs. reactive), and transmission interconnection cost allocated to a renewable generator (high vs. low). We find that market restructuring is not a primary driver of renewable energy development. Renewable generation has the highest percent of total installed capacity in markets that use a FIT, employ anticipatory transmission planning, and have loads or end-users paying for most, if not all, of the transmission interconnection costs. In contrast, renewable developers have been less successful in markets that do not use a FIT, employ reactive transmission planning, and have generators paying for most, if not all, of the transmission interconnection costs. While these policies can lead to higher penetration of renewable energy in the short run, their high cost to ratepayers can threaten the economic sustainability of renewable energy in the long-run. - Highlights: → Market structure seems to have little effect on renewable energy development. → Renewable energy development is more successful in markets that use a FIT. → Anticipatory transmission planning aids renewable energy development. → Low interconnection costs for developers also aids renewable energy development.

  10. Renewable energy education in Turkey

    Energy Technology Data Exchange (ETDEWEB)

    Acikgoz, Caglayan [Department of Chemical and Process Engineering, Faculty of Engineering, Bilecik University, P.O.11030, Bilecik (Turkey)

    2011-02-15

    Utilization of renewable energy sources and the application of environmentally sound energy technologies are essential to sustainable development and will help to secure the quality of living and the well-being of the future generations. Turkey presently has considerable renewable energy sources. The most important renewable sources are hydropower, wind, solar, geothermal, and biomass. The use of renewable energy as a topic to study energy and its forms permits a novel way to motivate students, particularly those who energy topics taking conscience with the environment. This paper presents the analysis and classification of renewable energy sources and how to find out their origin and a way to motivate students in energy topics related to renewable sources and also, the development of didactic competencies in special blended learning arrangements for educationalists, trainers and lecturers in adult education in the field of renewable energies in Turkey. (author)

  11. Superhydrophobicity construction with dye-sensitised TiO2 on fabric surface for both oil/water separation and water bulk contaminants purification

    Science.gov (United States)

    Yu, Linfeng; Zhang, Shengmiao; Zhang, Meng; Chen, Jianding

    2017-12-01

    For the promising material for both oil/water separation and water-soluble contaminants, the Dye@TiO2-TEOS/VTEO hybrid modified polyester fabric is developed by a simple dip-coating process, which combines Dye-sensitised TiO2 with silicon contained superhydrophobic coating to guarantee the long-term stability of Dye-sensitised TiO2 system as well as material's sustainability. The modified fabric possesses selective oil/water seperation properties towards water and oil, besides, mechanical, acid and alkali durability shows this material's appropriate performance on oil/water separation. UV-Vis absorption spectrum reveals the Dye 4-(2H-imidazol-2-ylazo) benzoic acid could sensitize the semiconductor TiO2 for visible light catalytic organic pollutant degradation that is also confirmed by methylene blue degradation experiment. Density Functional calculation (DFT) witnesses that HOMO, HOMO-1 of Dye contributed by oxygen bonding to TiO2 can insert into TiO2 band gap and result in low energy electron excitation. The ability of oil/water separation and water-soluble contaminants purification provides the material opportunity to practical applications in environmental restoration and human life.

  12. Boosting renewable energies

    International Nuclear Information System (INIS)

    Anon.

    2010-01-01

    Public policy and funding are basically different, but both are needed to develop the renewable energy market. Public policy creates incentives, but also obligations. The setting up of a 'repurchase rate' also called a 'feed-in tariff' or 'clean energy cash back scheme' obliges electric power companies to buy back energy of renewable origin at a fixed, guaranteed rate. The extra-cost generated, although usually low, is passed on to all customers and does not cost the State anything. Funding is characterized by its source, the manner in which it is obtained and who supplies it, whether it be banks, mutual funds, development agencies, electric power companies, local governments or the consumers themselves. Repurchasing yields regular cash flows over a given period at a lower risk and allows banks to provide funding. This is one of the reasons for its success. This solution is also very popular with political leaders because it does not weigh down public funding. Both these reasons explain why repurchasing is so appreciated in Europe and in a growing number of countries, more than seventy having adopted it in 2010. In addition, it is regularly discounted in relation to technological breakthroughs and lower costs. As is the case in Europe, the problem lies in maintaining an acceptable rate while avoiding excessive project profitability. In Europe, for instance, the number of renewable energy projects is such that consumers are starting to complain about seeing their electricity rates rise because of the famous feed-in tariff, even though the cost of renewable energies continues to drop on a regular basis. The United States and a few other countries, including China, prefer the quota system, or RPS (Renewable Portfolio Standards), which requires electric power companies to generate a minimal share of electric power by a renewable energy source. These companies consequently invest in renewable energy projects or purchase this energy from other suppliers. Like the

  13. Preparation of RF-(VM-SiO2n-RF/AM-Cellu Nanocomposites, and Use Thereof for the Modification of Glass and Filter Paper Surfaces: Creation of a Glass Thermoresponsive Switching Behavior and an Efficient Separation Paper Membrane

    Directory of Open Access Journals (Sweden)

    Hideo Sawada

    2017-03-01

    Full Text Available Fluoroalkyl end-capped vinyltrimethoxysilane oligomeric silica/alkyl-modified cellulose (AM-Cellu nanocomposites [RF-(CH2-CHSiO2n-RF/AM-Cellu; n = 2, 3; RF = CF(CF3OC3F7] were prepared by the sol-gel reactions of the corresponding oligomer [RF-(CH2-CHSi(OMe3n-RF] in the presence of AM-Cellu. The nanocomposites thus obtained were applied to the surface modification of glass to exhibit a highly oleophobic/superhydrophilic characteristic on the modified surface at 20 °C. Interestingly, a temperature dependence of contact angle values of dodecane and water was observed on the modified surface at 20~70 °C, and the dodecane contact angle values were found to decrease with increasing the temperatures from 20 to 70 °C to provide from highly oleophobic to superoleophilic characteristics on the surface. On the other hand, the increase of the water contact angle values was observed with the increase in the temperatures under similar conditions to supply superhydrophilic to superhydrophobic characteristics on the modified surface. The corresponding nanocomposites were also applied to the surface modification of the filter paper under similar conditions to afford a superoleophilic/superhydrophobic characteristic on the surface. It was demonstrated that the modified filter paper is effective for the separation membrane for W/O emulsion to isolate the transparent colorless oil.

  14. Renewable energy education for 21st century

    International Nuclear Information System (INIS)

    Charters, W.W.S.

    2000-01-01

    The major technological developments in equipment, designed to harness new and renewable sources of energy, have only taken place in the last four decades of the twentieth century, although the principles involved have been previously known for many centuries and were clearly formulated in many of the ancient civilizations. The term renewable energy (RE) itself is of relatively recent origin and only came into widespread use worldwide in the eighties, after the United Nations Conference on New and Renewable Sources of Energy, held in Nairobi, Kenya in 1981, Ref 1. Currently, the term renewable s is extensively used to describe the full range of direct and indirect uses of solar radiation incident on the earth's surface, and is often extended to include energy resources, such as tidal power or geothermal energy, neither of which is strictly renewable in the true sense of the word. Energy extracted from biomass is also generally included under this heading, although biomass is truly renewable only if continuous plantation development and replanting is carried out as the biomass is harvested. On a global scale, relatively extensive teaching about renewable energy started in the late seventies and early eighties, after the first impact of the OPEC oil price shock. Up till this time, there were only a few centres around the world where individual dedicated researchers and university teachers were involved in such activity. The next impetus to course and teaching material development came with national movements for energy independence and finally, in the latter years of this century, considerable stimulation has been given due to the increasing realisation of global environmental factors such as global warming, ozone depletion in the upper atmosphere, acid rain formation, and many other environmental degradation effects due to the increasing use of fossil fuel reserves. Considerable attention has been focused in the last twenty years through the many national and

  15. Flow Separation

    Science.gov (United States)

    1975-11-01

    procedant k une "correction de couche Halte" qul aura pour effet de placer le decollement en un point plus avanc« et, par Id, plus pro- che de celul trouve...couche Hmlte se comporte comae celul qul se produlralt sur la surface correapondant i la frontlire de fi. evaluee k partlr du premier calcul sans...proche de celul de Chapman-Rubesln que le nombre de coefficients retenu dans la relation gin^rale de Nielsen entre la temperature et la

  16. WIPP's Hazardous Waste Facility Permit Renewal Application

    International Nuclear Information System (INIS)

    Most, W.A.; Kehrman, R.F.

    2009-01-01

    Hazardous waste permits issued by the New Mexico Environment Department (NMED) have a maximum term of 10-years from the permit's effective date. The permit condition in the Waste Isolation Pilot Plant's (WIPP) Hazardous Waste Facility Permit (HWFP) governing renewal applications, directs the Permittees to submit a permit application 180 days prior to expiration of the Permit. On October 27, 1999, the Secretary of the NMED issued to the United States Department of Energy (DOE), the owner and operator of WIPP, and to Washington TRU Solutions LLC (WTS), the Management and Operating Contractor and the cooperator of WIPP, a HWFP to manage, store, and dispose hazardous waste at WIPP. The DOE and WTS are collectively known as the Permittees. The HWFP is effective for a fixed term not to exceed ten years from the effective date of the Permit. The Permittees may renew the HWFP by submitting a new permit application at least 180 calendar days before the expiration date, of the HWFP. The Permittees are not proposing any substantial changes in the Renewal Application. First, the Permittees are seeking the authority to dispose of Contact-Handled and Remote-Handled TRU mixed waste in Panel 8. Panels 4 through 7 have been approved in the WIPP Hazardous Waste Facility Permit as it currently exists. No other change to the facility or to the manner in which hazardous waste is characterized, managed, stored, or disposed is being requested. Second, the Permittees also seek to include the Mine Ventilation Rate Monitoring Plan, as Attachment Q in the HWFP. This Plan has existed as a separate document since May 2000. The NMED has requested that the Plan be submitted as part of the Renewal Application. The Permittees have been operating to the Mine Ventilation Rate Monitoring Plan since the Plan was submitted. Third, some information submitted in the original WIPP RCRA Part B Application has been updated, such as demographic information. The Permittees will submit this information in the

  17. Renewables 2017 Global Status Report

    International Nuclear Information System (INIS)

    Sawin, Janet L.; Sverrisson, Freyr; Seyboth, Kristin; Adib, Rana; Murdock, Hannah E.; Lins, Christine; Edwards, Isobel; Hullin, Martin; Nguyen, Linh H.; Prillianto, Satrio S.; Satzinger, Katharina; Appavou, Fabiani; Brown, Adam; Chernyakhovskiy, Ilya; Logan, Jeffrey; Milligan, Michael; Zinaman, Owen; Epp, Baerbel; Huber, Lon; Lyons, Lorcan; Nowak, Thomas; Otte, Pia; Skeen, Jonathan; Sovacool, Benjamin; Witkamp, Bert; Musolino, Evan; Brown, Adam; Williamson, Laura E.; Ashworth, Lewis; Mastny, Lisa

    2017-01-01

    Renewable energy technologies increase their hold across developing and emerging economies throughout the year The year 2016 saw several developments and ongoing trends that all have a bearing on renewable energy, including the continuation of comparatively low global fossil fuel prices; dramatic price declines of several renewable energy technologies; and a continued increase in attention to energy storage. For the third consecutive year, global energy-related carbon dioxide emissions from fossil fuels and industry were nearly flat in 2016, due largely to declining coal use worldwide but also due to improvements in energy efficiency and to increasing use of renewable energy. As of 2015, renewable energy provided an estimated 19.3% of global final energy consumption, and growth in capacity and production continued in 2016. The power sector experienced the greatest increases in renewable energy capacity in 2016, whereas the growth of renewables in the heating and cooling and transport sectors was comparatively slow. Most new renewable energy capacity is installed in developing countries, and largely in China, the single largest developer of renewable power and heat over the past eight years. In 2016, renewable energy spread to a growing number of developing and emerging economies, some of which have become important markets. For the more than 1 billion people without access to electricity, distributed renewable energy projects, especially those in rural areas far from the centralised grid, offer important and often cost-effective options to provide such access. The renewable energy sector employed 9.8 million people in 2016, an increase of 1.1% over 2015. By technology, solar PV and biofuels provided the largest numbers of jobs. Employment shifted further towards Asia, which accounted for 62% of all renewable energy jobs (not including large-scale hydropower), led by China. The development of community renewable energy projects continued in 2016, but the pace of

  18. Management of development of renewable energy sources

    Directory of Open Access Journals (Sweden)

    Inić Branimir P.

    2014-01-01

    Full Text Available The aim of the paper: 'Management of development of renewable energy sources is to point out the possible solutions for neutralizing the threat of energy shortages. The paper outlines major short and long term energy problems facing humanity. The increase of world human population is, inevitably, accompanied by higher energy consumption. Reserves decrease of nonrenewable energy sources like oil, gas, and coal is a major threat to maintaining current living conditions, and thus requires solutions in order to neutralize the threat. This is why the management of development of renewable energy sources is an imperative for Serbia. The paper emphasizes the use of solar energy, because the annual average of solar radiation in Serbia is about 40% higher than the European average, however, the actual use of the sun's energy to generate electricity in Serbia is far behind the countries of the European Union. Solar energy is clean, renewable, and the fact that 4.2 kilowatt-hours are received daily per square meter averaged over the entire surface of the planet, makes it an almost unused energy source, Compared to EU countries, the price of non-renewable derived energy is, on average, higher in Serbia. Taking this into consideration, the use of solar energy, as an unused resource, imposes itself as indispensable.

  19. Sibling rivalry, separation, and change in Austen's Sense and Sensibility.

    Science.gov (United States)

    Fitzpatrick Hanly, Margaret Ann

    2016-08-01

    The paper explores a process of growth represented in the interplay of Jane Austen's characterizations of Marianne and Elinor Dashwood in Sense and Sensibility, approaching the text through the lens of psychoanalytic theories on oedipal sibling rivalry, separation, and processes of change. A close reading of Sense and Sensibility tracks Marianne Dashwood's repudiation of any 'second attachment' as the surface of an unconscious fantasy, denying a rival for the mother's love. A psychoanalytic view contrasts Marianne's lack of separation from her mother, her use of denial and projection, and her near death after losing the man she loves, with her older sister Elinor Dashwood's capacities for depression, reflection, and greater acceptance of loss and separation. The narrative portrays Mrs. Dashwood's identification with and idealization of her daughter Marianne, which contribute to her oedipal sibling 'victory'. In the language and structure of the novel, the projections, identifications, aggressions, and separations (conscious and unconscious) of the sisters in the vicissitudes of their adolescent loves and rivalries constitute a process of growth. Austen's novel brings to life, with the vividness and coherence of great literature, forces and fantasies in oedipal sibling rivalries, inspiring renewed attention to their subtle presence in the transference and countertransference of the psychoanalytic process. Copyright © 2015 Institute of Psychoanalysis.

  20. Polymeric materials from renewable resources

    Energy Technology Data Exchange (ETDEWEB)

    Frollini, Elisabete; Rodrigues, Bruno V. M.; Silva, Cristina G. da; Castro, Daniele O.; Ramires, Elaine C.; Oliveira, Fernando de; Santos, Rachel P. O. [Macromolecular Materials and Lignocellulosic Fibers Group, Center for Research on Science and Technology of BioResources, Institute of Chemistry of São Carlos, University of São Paulo, CP 780, 13560-970 São Carlos, São Paulo (Brazil)

    2016-05-18

    The goals of our studies have been the use of renewable raw materials in the preparation of polymeric materials with diversified properties. In this context, lignosulfonate, which is produced in large scale around the world, but not widely used in the production of polymeric materials, was used to replace phenol and polyols in the preparation of phenolic- (Ligno-PH) and polyurethane-type (Ligno-PU) polymers, respectively. These polymers were used to prepare composites reinforced with sisal lignocellulosic fibers. The use of lignosulfonate in the formulation of both types of polymers was beneficial, because in general composites with improved properties, specially impact strength, were obtained. Composites were also prepared from the so called “biopolyethylene” (HDPE), curaua lignocellulosic fiber, and castor oil (CO). All composites HDBPE/CO/Fiber exhibited higher impact strength, when compared to those of the corresponding HDBPE/Fiber. These results, combined with others (eg SEM images of the fractured surfaces) indicated that, in addition to acting as a plasticizer, this oil may have acted as a compatibilizer of the hydrophilic fiber with the hydrophobic polymer. The set of results indicated that (i) mats with nano (diameter ≤ 100nm) and/or ultrafine (submicron scale) fibers were produced, (ii) hybrid fibers were produced (bio-based mats composites), (iii) cellulosic pulp (CP) and/or lignin (Lig) can be combined with PET matrices to control properties such as stiffness and hydrophilicity of the respective mats. Materials with diversified properties were prepared from high content of renewable raw materials, thus fulfilling the proposed targets.

  1. Polymeric materials from renewable resources

    Science.gov (United States)

    Frollini, Elisabete; Rodrigues, Bruno V. M.; da Silva, Cristina G.; Castro, Daniele O.; Ramires, Elaine C.; de Oliveira, Fernando; Santos, Rachel P. O.

    2016-05-01

    The goals of our studies have been the use of renewable raw materials in the preparation of polymeric materials with diversified properties. In this context, lignosulfonate, which is produced in large scale around the world, but not widely used in the production of polymeric materials, was used to replace phenol and polyols in the preparation of phenolic- (Ligno-PH) and polyurethane-type (Ligno-PU) polymers, respectively. These polymers were used to prepare composites reinforced with sisal lignocellulosic fibers. The use of lignosulfonate in the formulation of both types of polymers was beneficial, because in general composites with improved properties, specially impact strength, were obtained. Composites were also prepared from the so called "biopolyethylene" (HDPE), curaua lignocellulosic fiber, and castor oil (CO). All composites HDBPE/CO/Fiber exhibited higher impact strength, when compared to those of the corresponding HDBPE/Fiber. These results, combined with others (eg SEM images of the fractured surfaces) indicated that, in addition to acting as a plasticizer, this oil may have acted as a compatibilizer of the hydrophilic fiber with the hydrophobic polymer. The set of results indicated that (i) mats with nano (diameter ≤ 100nm) and/or ultrafine (submicron scale) fibers were produced, (ii) hybrid fibers were produced (bio-based mats composites), (iii) cellulosic pulp (CP) and/or lignin (Lig) can be combined with PET matrices to control properties such as stiffness and hydrophilicity of the respective mats. Materials with diversified properties were prepared from high content of renewable raw materials, thus fulfilling the proposed targets.

  2. Separations chemistry

    International Nuclear Information System (INIS)

    Anon.

    1977-01-01

    Infrared spectra of Pu(IV) polymer show effects of CO 2 adsorption and of aging. Uv light (300 nm) increases the rate of reduction of PuO 2 2+ and Pu 4+ to Pu 3+ and the Pu--U separation factor using TBP. Distribution ratios for Zr and Hf between Dowex 50W--X8 resin and H 2 SO 4 solutions were found to decrease sharply with H 2 SO 4 content. Octylphenyl acid phosphate, a mixture of monooctylphenyl and dioctylphenyl phosphoric acids, is being studied for U recovery from wet-process phosphoric acid. A study of HNO 3 leaching of Ra from U ores was completed. Effects of particle size of the packed bed on the dispersion of the boundary of the miscible phase used in oil recovery are being studied. Effects of sulfonates on toluene--n-butanol--water phase relations were determined, as were the effects of salts and solutes on the max water content of 1:1 toluene--alcohol solutions. A study was begun of hydrocarbon solubility in water--surfactant--alcohol. The mechanism of the formation of hydrous ZrO 2 --polyacrylate membranes and their use for sulfate rejection were studied. Salt rejection through hyperfiltration by clay membranes (bentonite and kaolin) was also investigated. Preliminary results are given for hyperfiltration of wood-pulping wastes by ZrO 2 membranes. 13 figures

  3. Proceedings of the 2010 renewable energy infrastructure workshop

    International Nuclear Information System (INIS)

    2010-01-01

    This workshop provided a forum for electric power industry leaders and key stakeholders to discuss Canada's renewable energy infrastructure needs. The workshop was held to provide practical solutions for meeting the increased demand for renewable energy as well as to offer a range of marketplace options and funding opportunities. Participants in the workshop examined the regulatory framework of the Green Energy Act and its potential impact on organizations. Approval process procedures for renewable energy projects were reviewed, and methods of ensuring the integration of renewable energy projects with current business strategies were discussed. Communications strategies for managing the public perception of energy project were presented. Policy barriers to infrastructure development were outlined. Methods of developing partnerships with Aboriginal communities were also discussed. The conference featured 16 presentations, of which 3 have been catalogued separately for inclusion in this database. tabs., figs.

  4. Tandem assays of protein and glucose with functionalized core/shell particles based on magnetic separation and surface-enhanced Raman scattering.

    Science.gov (United States)

    Kong, Xianming; Yu, Qian; Lv, Zhongpeng; Du, Xuezhong

    2013-10-11

    Tandem assays of protein and glucose in combination with mannose-functionalized Fe3 O4 @SiO2 and Ag@SiO2 tag particles have promising potential in effective magnetic separation and highly sensitive and selective SERS assays of biomaterials. It is for the first time that tandem assay of glucose is developed using SERS based on the Con A-sandwiched microstructures between the functionalized magnetic and tag particles. Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  5. Talking Renewables; A renewable energy primer for everyone

    Science.gov (United States)

    Singh, Anirudh

    2018-03-01

    This book provides a clear and factual picture of the status of renewable energy and its capabilities today. The book covers all areas of renewable energy, starting from biomass energy and hydropower and proceeding to wind, solar and geothermal energy before ending with an overview of ocean energy. The book also explores how the technologies are being implemented today and takes a look at the future of renewable energy.

  6. Renewable energy rebound effect?: Estimating the impact of state renewable energy financial incentives on residential electricity consumption

    Science.gov (United States)

    Stephenson, Beth A.

    Climate change is a well-documented phenomenon. If left unchecked greenhouse gas emissions will continue global surface warming, likely leading to severe and irreversible impacts. Generating renewable energy has become an increasingly salient topic in energy policy as it may mitigate the impact of climate change. State renewable energy financial incentives have been in place since the mid-1970s in some states and over 40 states have adopted one or more incentives at some point since then. Using multivariate linear and fixed effects regression for the years 2002 through 2012, I estimate the relationship between state renewable energy financial incentives and residential electricity consumption, along with the associated policy implications. My hypothesis is that a renewable energy rebound effect is present; therefore, states with renewable energy financial incentives have a higher rate of residential electricity consumption. I find a renewable energy rebound effect is present in varying degrees for each model, but the results do not definitively indicate how particular incentives influence consumer behavior. States should use caution when adopting and keeping renewable energy financial incentives as this may increase consumption in the short-term. The long-term impact is unclear, making it worthwhile for policymakers to continue studying the potential for renewable energy financial incentives to alter consumer behavior.

  7. Regional Renewable Energy Cooperatives

    Science.gov (United States)

    Hazendonk, P.; Brown, M. B.; Byrne, J. M.; Harrison, T.; Mueller, R.; Peacock, K.; Usher, J.; Yalamova, R.; Kroebel, R.; Larsen, J.; McNaughton, R.

    2014-12-01

    We are building a multidisciplinary research program linking researchers in agriculture, business, earth science, engineering, humanities and social science. Our goal is to match renewable energy supply and reformed energy demands. The program will be focused on (i) understanding and modifying energy demand, (ii) design and implementation of diverse renewable energy networks. Geomatics technology will be used to map existing energy and waste flows on a neighbourhood, municipal, and regional level. Optimal sites and combinations of sites for solar and wind electrical generation (ridges, rooftops, valley walls) will be identified. Geomatics based site and grid analyses will identify best locations for energy production based on efficient production and connectivity to regional grids and transportation. Design of networks for utilization of waste streams of heat, water, animal and human waste for energy production will be investigated. Agriculture, cities and industry produce many waste streams that are not well utilized. Therefore, establishing a renewable energy resource mapping and planning program for electrical generation, waste heat and energy recovery, biomass collection, and biochar, biodiesel and syngas production is critical to regional energy optimization. Electrical storage and demand management are two priorities that will be investigated. Regional scale cooperatives may use electric vehicle batteries and innovations such as pump storage and concentrated solar molten salt heat storage for steam turbine electrical generation. Energy demand management is poorly explored in Canada and elsewhere - our homes and businesses operate on an unrestricted demand. Simple monitoring and energy demand-ranking software can easily reduce peaks demands and move lower ranked uses to non-peak periods, thereby reducing the grid size needed to meet peak demands. Peak demand strains the current energy grid capacity and often requires demand balancing projects and

  8. Introduction to renewable energy

    CERN Document Server

    Nelson, Vaughn C

    2011-01-01

    IntroductionEnergy and SocietyTypes of EnergyRenewable EnergyAdvantages/DisadvantagesEconomicsGlobal WarmingOrder of Magnitude EstimatesGrowth (Exponential)SolutionsEnergyIntroductionDefinition of Energy and PowerHeatThermodynamicsEnergy Dilemma in Light of the Laws of ThermodynamicsUse of Fossil FuelsNuclearFinite ResourceSummarySunSolar PowerElectromagnetic SpectrumEnergy Balance of the EarthEarth-Sun MotionInsolationSolar ResourceGreenhouse EffectHeat Transfer and StorageIntroductionConductionConvectionRadiationThermal MassSeasonal Heating or CoolingThermal ComfortSolar Heating and CoolingB

  9. Renewable sources of energy

    International Nuclear Information System (INIS)

    Wojas, K.

    1996-01-01

    The author takes a look at causes of the present interest in the renewable, natural sources of energy. These are: the fuel deposits becoming exhausted, hazard to environment (especially carbon dioxide) and accessibility of these sources for under-developed countries. An interrelation is shown between these sources and the energy circulations connected with atmosphere and ocean systems. The chief ones from among them that are being used now are discussed, i.e. solar radiation, wind, water waves energy, tides, geothermal heat, and the like. Problems of conversion of the forms of these kinds of energy are also given a mention. (author)

  10. 78 FR 12005 - Regulation of Fuels and Fuel Additives: 2013 Renewable Fuel Standards; Public Hearing

    Science.gov (United States)

    2013-02-21

    ... Regulation of Fuels and Fuel Additives: 2013 Renewable Fuel Standards; Public Hearing AGENCY: Environmental... EPA is announcing a public hearing to be held for the proposed rule ``Regulation of Fuels and Fuel Additives: 2013 Renewable Fuel Standards,'' which was published separately in the Federal Register on...

  11. Renewable Energy Country Attractiveness Indices

    International Nuclear Information System (INIS)

    2011-02-01

    Since 2003 Ernst and Young team has been releasing quarterly data that ranks national renewable energy markets, and their suitability for individual technologies. The Country Attractiveness Indices now track the relative attractiveness of 30 countries' renewable energy markets across a selection of technologies each quarter. The Renewable Energy Country Attractiveness Indices publication scores and comments on various technologies, including: on-shore wind, off-shore wind, solar PV, solar CSP, biomass, and geothermal.

  12. Policies for a renewable future

    International Nuclear Information System (INIS)

    Anon.

    1992-01-01

    This chapter identifies changes needed in policies regarding the utilization of renewable energy sources. The topics of the chapter include financial and legal incentives, information needs, long range energy and economic policy, environmental issues as an impetus to commercialization of renewable energy sources, taxing use of fossil fuels, encouraging renewable energy use by electric utilities through least-cost planning, educating the public and providing technical assistance, research and development, and environmental regulation and monitoring

  13. Renewable energy development in China

    Energy Technology Data Exchange (ETDEWEB)

    Junfeng, Li

    1996-12-31

    This paper presents the resources availability, technologies development and their costs of renewable energies in China and introduces the programs of renewable energies technologies development and their adaptation for rural economic development in China. As the conclusion of this paper, renewable energies technologies are suitable for some rural areas, especially in the remote areas for both household energy and business activities energy demand. The paper looks at issues involving hydropower, wind energy, biomass combustion, geothermal energy, and solar energy.

  14. Visions of regulatory renewal

    International Nuclear Information System (INIS)

    Edgeworth, A.

    1998-01-01

    The economic contribution of the CEPA (Canadian Energy Pipeline Association) member companies to Canada's trade balance was discussed. CEPA member companies transport 95 per cent of the crude oil and natural gas produced in Canada to domestic and export markets. This represents a total of 5.6 Tcf of gas annually. Half of Canada's natural gas and oil production is exported to U.S. markets. All of these exports are transported by pipeline. CEPA member companies operate 90,000 km of pipeline from British Columbia to Quebec. Expansions are needed as a result of a significant increase in demand for natural gas and crude oil since 1990. Several issues exist for regulatory renewal. They include the need to create a level playing field, the overseeing of tolls and contract renewal terms, changing risk/reward trade-offs, the right to confidentiality of information and price discovery mechanism. The drivers for regulatory reform at Westcoast Energy are the need for pricing flexibility, customers desire for toll certainty, decontracting and opposition to rolled-in expansions for gathering and processing. An overview of Westcoast Energy's negotiated toll settlement, its implications, and the components of Westcoast Energy's 'light handed regulation' (LHR) was presented

  15. Renewable Energy Marketplace

    Science.gov (United States)

    Ghadimian, Vachik

    The renewable energy sector is evolving, and today, renewable energy has become a viable alternative for many facilities. Because this sector is in its infancy stage, lack of experience has resulted in failing solar projects. This project involves the design and implementation of a functioning web application that streamlines and automates the planning, risk assessment and financing of a solar development project. The three key stakeholders, the host facility, solar installer and financier are seamlessly integrated into a single marketplace. By designing a project development workflow, projects are vetted early on and terminated if deemed infeasible, saving time and resources. By risk assessing the project using the proposed scoring model, one can inherit more confident investors. The project scoring model also serves as a debt rating system, where investors can measure the risk/rewards. The platform will also serve as a communication medium between the three stakeholders. Besides storing documents like engineering drawings, permits, etc., the platform auto-generates all necessary transactional documents, legal documents and agreements among the three stakeholders.

  16. Mexican renewable electricity law

    Energy Technology Data Exchange (ETDEWEB)

    Ruiz-Mendoza, B.J.; Sheinbaum-Pardo, C. [Institute of Engineering of the National Autonomous University of Mexico, Circuito Exterior s/n, Edificio 12 Bernardo Quintana, Piso 3, Cubiculo 319, Ciudad Universitaria, Delegacion Coyoacan, CP 04510, Mexico D.F. (Mexico)

    2010-03-15

    Two renewable electricity bills have been proposed in Congress since 2005 in Mexico. The first one was rejected by the Senate and the second one was approved by both the House of Representatives and the Senate in October 2008. Our objective is to explain the nature of both bills and to analyze each of them bearing in mind the Mexican electricity sector management scheme. In the Mexican electricity sector single-buyer scheme, the state-owned companies (Comision Federal de Electricidad and Luz y Fuerza del Centro) are responsible of the public services and the private sector generates electricity under six modalities: self-supply, cogeneration, independent production, small production, export, and import, which are not considered a public service. This scheme has caused controversies related to the constitutionality of the 1992 Power Public Services Law that allowed this scheme to be implemented. Both bills, the rejected one and the approved one, were formulated and based on that controversial law and their objectives are linked precisely more to the controversial issues than to the promotion of renewable electricity technologies; consequently, the gap among environmental, economic and social issues related with sustainability notion is wider. (author)

  17. Mexican renewable electricity law

    International Nuclear Information System (INIS)

    Ruiz-Mendoza, B.J.; Sheinbaum-Pardo, C.

    2010-01-01

    Two renewable electricity bills have been proposed in Congress since 2005 in Mexico. The first one was rejected by the Senate and the second one was approved by both the House of Representatives and the Senate in October 2008. Our objective is to explain the nature of both bills and to analyze each of them bearing in mind the Mexican electricity sector management scheme. In the Mexican electricity sector single-buyer scheme, the state-owned companies (Comision Federal de Electricidad and Luz y Fuerza del Centro) are responsible of the public services and the private sector generates electricity under six modalities: self-supply, cogeneration, independent production, small production, export, and import, which are not considered a public service. This scheme has caused controversies related to the constitutionality of the 1992 Power Public Services Law that allowed this scheme to be implemented. Both bills, the rejected one and the approved one, were formulated and based on that controversial law and their objectives are linked precisely more to the controversial issues than to the promotion of renewable electricity technologies; consequently, the gap among environmental, economic and social issues related with sustainability notion is wider. (author)

  18. Renewables 2007 - Global status report

    International Nuclear Information System (INIS)

    Martinot, Eric; Mastny, Lisa; Rosbotham, Lyle; Suding, Paul; Sonntag-O'Brien, Virginia; Lempp, Philippe

    2007-01-01

    In 2007, more than $100 billion was invested in new renewable energy capacity, manufacturing plants, and research and development-a true global milestone. Yet perceptions lag behind the reality of renewable energy because change has been so rapid in recent years. This report captures that reality and provides an overview of the status of renewable energy worldwide in 2007. The report covers trends in markets, investments, industries, policies, and rural (off-grid) renewable energy. (By design, the report does not provide analysis, discuss current issues, or forecast the future.) Many of the trends reflect increasing significance relative to conventional energy

  19. Integrating Renewables in Electricity Markets

    DEFF Research Database (Denmark)

    Morales González, Juan Miguel; Conejo, Antonio J.; Madsen, Henrik

    in the electricity market. • The development of procedures to enable demand response and to facilitate the integration of stochastic renewable units. This book is written in a modular and tutorial manner and includes many illustrative examples to facilitate its comprehension. It is intended for advanced...... such as: • The modeling and forecasting of stochastic renewable power production. • The characterization of the impact of renewable production on market outcomes. • The clearing of electricity markets with high penetration of stochastic renewable units. • The development of mechanisms to counteract...

  20. Economics of nuclear and renewables

    International Nuclear Information System (INIS)

    Khatib, Hisham; Difiglio, Carmine

    2016-01-01

    This paper provides an assessment of the economic challenges faced by both nuclear power and “new” renewable electricity technologies. The assessment reflects the need to incorporate new renewables into power grids and issues faced in dispatching power and their effect on traditional electricity technologies as well as the need for transmission extension and/or grid reinforcement. Wider introduction of smart grids and the likely demise of nuclear in some OECD countries are bound to enhance the future prospects for new renewables. However, their immediate future expansion will depend on continued subsidies, which are becoming difficult to sustain in present economic circumstances. Development of large energy storage facilities and carbon pricing could significantly enhance future renewable energy prospects. Correspondingly, expanding renewable energy, in spite of their popularity with some governments and sections of the public, is likely to face challenges which will slow their present rapid progress. Nuclear is now shied away from in many industrialized countries and having mixed prospects in developing economies. In many instances, it suffers from high initial costs, long lead times and often excessive construction delays. Nuclear power also faces challenging risks – investment as well as regulatory. In contrast to renewables, its share of global energy consumption is declining. - Highlights: •Renewables are increasing their energy share. •Renewables system cost is higher than their production cost. •Nuclear share is not increasing and their costs are not reduced. •Discount rate and subsidies are important in economics of renewables and nuclear.

  1. Regulatory guidance for license renewal

    International Nuclear Information System (INIS)

    Thoma, John A.

    1991-01-01

    The proposed 10 CFR Part 54 rule proceduralizes the process for license renewal by identifying both the administrative and technical requirements for a renewal application. To amplify and support this regulation, written guidance has been provided in the form of a draft Regulatory Guide (DG 1009) and a draft Standard Review Plan for License Renewal (NUREG 1299). This guidance is scheduled to be finalized in 1992. Similar guidance will be provided for the proposed revisions to 10 CFR Part 51 concerning the environmental aspects of license renewal. (author)

  2. Separation science and technology

    International Nuclear Information System (INIS)

    Smith, B.F.; Sauer, N.; Chamberlin, R.M.; Gottesfeld, S.; Mattes, B.R.; Li, D.Q.; Swanson, B.

    1998-01-01

    The focus of this project is the demonstration and advancement of membrane-based separation and destruction technologies. The authors are exploring development of membrane systems for gas separations, selective metal ion recovery, and for separation or destruction of hazardous organics. They evaluated existing polymers and polymer formulations for recovery of toxic oxyanionic metals such as chromate and arsenate from selected waste streams and developed second-generation water-soluble polymeric systems for highly selective oxyanion removal and recovery. They optimized the simultaneous removal of radioactive strontium and cesium from aqueous solutions using the new nonhazardous separations agents, and developed recyclable, redox-active extractants that permitted recovery of the radioactive ions into a minimal waste volume. They produced hollow fibers and fabricated prototype hollow-fiber membrane modules for applications to gas separations and the liquid-liquid extraction and recovery of actinides and nuclear materials from process streams. They developed and fabricated cyclodextrin-based microporous materials that selectively absorb organic compounds in an aqueous environment; the resultant products gave pure water with organics at less than 0.05 parts per billion. They developed new, more efficient, membrane-based electrochemical reactors for use in organic destruction in process waste treatment. They addressed the need for advanced oxidation technologies based on molecular-level materials designs that selectively remove or destroy target species. They prepared and characterized surface-modified TiO 2 thin films using different linking approaches to attach ruthenium photosensitizers, and they started the measurement of the photo-degradation products generated using surface modified TiO 2 films in reaction with chlorophenol

  3. 78 FR 69628 - Public Hearing for the 2014 Standards for the Renewable Fuel Standard Program

    Science.gov (United States)

    2013-11-20

    ..., biomass-based diesel, advanced biofuel, and renewable fuels that would apply to all gasoline and diesel produced in the U.S. or imported in the year 2014. In addition, the separate proposal includes a proposed...

  4. Effects of pressure, temperature and atomic exchanges on phase separation dynamics in Au/Ni(111) surface alloy: Kinetic Monte Carlo study

    Energy Technology Data Exchange (ETDEWEB)

    Zvejnieks, G. [Institute for Solid State Physics, University of Latvia, Kengaraga 8, LV-1063 Riga (Latvia); Ibenskas, A., E-mail: ibenskas@pfi.lt [Center for Physical Sciences and Technology, Semiconductor Physics Institute, Gostauto 11, LT-01108 Vilnius (Lithuania); Tornau, E.E. [Center for Physical Sciences and Technology, Semiconductor Physics Institute, Gostauto 11, LT-01108 Vilnius (Lithuania)

    2015-11-15

    Instability of the Au/Ni(111) surface alloy is studied in different CO gas pressure, p, and temperature limits using kinetic Monte Carlo simulations. We analyze the reaction front dynamics and formation of Au clusters using the model which takes into account surface adatom pair and three-body interactions, CO adsorption and desorption, catalytic carbonyl formation reaction, Au and Ni adatom diffusion and their concerted exchange. Variation of interaction parameters allows us to identify three possible reaction front propagation limits with different pressure dependencies: (i) slow channel-like flow in agreement with experimental data [1] (step flow rate, R, increases with p), (ii) intermediate regime (weak p–dependence), and (iii) fast homogeneous flow (R decreases with p). We find that only Au–Ni exchange, contrary to both Ni–CO and Au–CO exchanges, significantly reduces the number of screened Ni atoms inside the Au clusters and stimulates the occurrence of Ni-free Au clusters. The size of Au islands depends on both pressure and temperature. At a fixed temperature it decreases with pressure due to an increased step flow rate. In the high temperature limit, despite the step flow rate exponential increase with temperature, the cluster size increases due to an enhanced Au mobility. - Highlights: • Kinetic Monte Carlo study of Au–Ni surface alloy instability to CO pressure and temperature. • Three reaction front propagation regimes. • In channel-like regime, the step flow rate increases with CO pressure as in experiment. • Ni-free Au islands are obtained when Au-Ni adatom exchange mechanism is considered. • The size of Au islands decreases with pressure and increases with temperature.

  5. Effects of pressure, temperature and atomic exchanges on phase separation dynamics in Au/Ni(111) surface alloy: Kinetic Monte Carlo study

    International Nuclear Information System (INIS)

    Zvejnieks, G.; Ibenskas, A.; Tornau, E.E.

    2015-01-01

    Instability of the Au/Ni(111) surface alloy is studied in different CO gas pressure, p, and temperature limits using kinetic Monte Carlo simulations. We analyze the reaction front dynamics and formation of Au clusters using the model which takes into account surface adatom pair and three-body interactions, CO adsorption and desorption, catalytic carbonyl formation reaction, Au and Ni adatom diffusion and their concerted exchange. Variation of interaction parameters allows us to identify three possible reaction front propagation limits with different pressure dependencies: (i) slow channel-like flow in agreement with experimental data [1] (step flow rate, R, increases with p), (ii) intermediate regime (weak p–dependence), and (iii) fast homogeneous flow (R decreases with p). We find that only Au–Ni exchange, contrary to both Ni–CO and Au–CO exchanges, significantly reduces the number of screened Ni atoms inside the Au clusters and stimulates the occurrence of Ni-free Au clusters. The size of Au islands depends on both pressure and temperature. At a fixed temperature it decreases with pressure due to an increased step flow rate. In the high temperature limit, despite the step flow rate exponential increase with temperature, the cluster size increases due to an enhanced Au mobility. - Highlights: • Kinetic Monte Carlo study of Au–Ni surface alloy instability to CO pressure and temperature. • Three reaction front propagation regimes. • In channel-like regime, the step flow rate increases with CO pressure as in experiment. • Ni-free Au islands are obtained when Au-Ni adatom exchange mechanism is considered. • The size of Au islands decreases with pressure and increases with temperature

  6. Separating Bulk and Surface Contributions to Electronic Excited-State Processes in Hybrid Mixed Perovskite Thin Films via Multimodal All-Optical Imaging.

    Science.gov (United States)

    Simpson, Mary Jane; Doughty, Benjamin; Das, Sanjib; Xiao, Kai; Ma, Ying-Zhong

    2017-07-20

    A comprehensive understanding of electronic excited-state phenomena underlying the impressive performance of solution-processed hybrid halide perovskite solar cells requires access to both spatially resolved electronic processes and corresponding sample morphological characteristics. Here, we demonstrate an all-optical multimodal imaging approach that enables us to obtain both electronic excited-state and morphological information on a single optical microscope platform with simultaneous high temporal and spatial resolution. Specifically, images were acquired for the same region of interest in thin films of chloride containing mixed lead halide perovskites (CH 3 NH 3 PbI 3-x Cl x ) using femtosecond transient absorption, time-integrated photoluminescence, confocal reflectance, and transmission microscopies. Comprehensive image analysis revealed the presence of surface- and bulk-dominated contributions to the various images, which describe either spatially dependent electronic excited-state properties or morphological variations across the probed region of the thin films. These results show that PL probes effectively the species near or at the film surface.

  7. Surface Nanostructures Formed by Phase Separation of Metal Salt-Polymer Nanocomposite Film for Anti-reflection and Super-hydrophobic Applications

    Science.gov (United States)

    Con, Celal; Cui, Bo

    2017-12-01

    This paper describes a simple and low-cost fabrication method for multi-functional nanostructures with outstanding anti-reflective and super-hydrophobic properties. Our method employed phase separation of a metal salt-polymer nanocomposite film that leads to nanoisland formation after etching away the polymer matrix, and the metal salt island can then be utilized as a hard mask for dry etching the substrate or sublayer. Compared to many other methods for patterning metallic hard mask structures, such as the popular lift-off method, our approach involves only spin coating and thermal annealing, thus is more cost-efficient. Metal salts including aluminum nitrate nonahydrate (ANN) and chromium nitrate nonahydrate (CNN) can both be used, and high aspect ratio (1:30) and high-resolution (sub-50 nm) pillars etched into silicon can be achieved readily. With further control of the etching profile by adjusting the dry etching parameters, cone-like silicon structure with reflectivity in the visible region down to a remarkably low value of 2% was achieved. Lastly, by coating a hydrophobic surfactant layer, the pillar array demonstrated a super-hydrophobic property with an exceptionally high water contact angle of up to 165.7°.

  8. Renewable Acrylonitrile Production

    Energy Technology Data Exchange (ETDEWEB)

    Beckham, Gregg T [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Karp, Eric M [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Eaton, Todd R [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Sanchez i Nogue, Violeta [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Vorotnikov, Vassili [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Biddy, Mary J [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Tan, Eric C [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Brandner, David [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Manker, Lorenz [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Michener, William E [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Vardon, Derek R [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Bratis, Adam D [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Liu, Rongming [University of Colorado; Gill, Ryan T. [University of Colorado; Gilhespy, Michelle [Johnson Matthey Technology Centre; Skoufa, Zinovia [Johnson Matthey Technology Centre; Watson, Michael J. [Johnson Matthey Technology Centre; Fruchey, O. Stanley [MATRIC; Cywar, Robin M. [Formerly NREL

    2017-12-08

    Acrylonitrile (ACN) is a petroleum-derived compound used in resins, polymers, acrylics, and carbon fiber. We present a process for renewable ACN production using 3-hydroxypropionic acid (3-HP), which can be produced microbially from sugars. The process achieves ACN molar yields exceeding 90% from ethyl 3-hydroxypropanoate (ethyl 3-HP) via dehydration and nitrilation with ammonia over an inexpensive titanium dioxide solid acid catalyst. We further describe an integrated process modeled at scale that is based on this chemistry and achieves near-quantitative ACN yields (98 +/- 2%) from ethyl acrylate. This endothermic approach eliminates runaway reaction hazards and achieves higher yields than the standard propylene ammoxidation process. Avoidance of hydrogen cyanide as a by-product also improves process safety and mitigates product handling requirements.

  9. Rewards of renewables

    Science.gov (United States)

    McNamee, Gregory

    2008-09-01

    In 1987 an American-style fridge freezer would use about 950 kWh of electricity and cost about 150 (£80) a year to run. Two decades on, a comparable appliance uses half the electricity and costs less than half as much to run. In 1975 there were about 3780 000 cars on the streets of Los Angeles, whereas today there are more than 5200 000 - yet air-pollution levels have fallen by half and an increasing number of those vehicles are hybrids or rely on renewable fuels like bio-diesel. Last year, half a million homes in Southern California were receiving direct solar power, either from solar electricity plants or from rooftop photovoltaic panels.

  10. Marine Renewable Energy Seascape

    Directory of Open Access Journals (Sweden)

    Alistair G.L. Borthwick

    2016-03-01

    Full Text Available Energy production based on fossil fuel reserves is largely responsible for carbon emissions, and hence global warming. The planet needs concerted action to reduce fossil fuel usage and to implement carbon mitigation measures. Ocean energy has huge potential, but there are major interdisciplinary problems to be overcome regarding technology, cost reduction, investment, environmental impact, governance, and so forth. This article briefly reviews ocean energy production from offshore wind, tidal stream, ocean current, tidal range, wave, thermal, salinity gradients, and biomass sources. Future areas of research and development are outlined that could make exploitation of the marine renewable energy (MRE seascape a viable proposition; these areas include energy storage, advanced materials, robotics, and informatics. The article concludes with a sustainability perspective on the MRE seascape encompassing ethics, legislation, the regulatory environment, governance and consenting, economic, social, and environmental constraints. A new generation of engineers is needed with the ingenuity and spirit of adventure to meet the global challenge posed by MRE.

  11. Resources: the renewable promises

    International Nuclear Information System (INIS)

    Bellin, I.; Damier, J.; Persiaux, R.

    2010-01-01

    A set of brief articles gives an overview of development perspectives and objectives for renewable energies in France (biomass, hydraulic, wind, geothermal, solar, and sea energies). The influence of public investments and subsidies, and possible technological developments are evoked for solar energy. The advances of various projects and ideas in the field of sea energy are discussed: sea current energy, wave and swell energy, offshore wind generators, ocean thermal energy. The objectives and impacts of the use of biomass and of the development of bio-refineries are discussed, as well as the challenge CO 2 capture and storage. The evolution of electricity networks is outlined in terms of electricity storage, demand management and energy saving

  12. Renewable Energy Certificate Program

    Energy Technology Data Exchange (ETDEWEB)

    Gwendolyn S. Andersen

    2012-07-17

    This project was primarily to develop and implement a curriculum which will train undergraduate and graduate students at the University seeking a degree as well as training for enrollees in a special certification program to prepare individuals to be employed in a broad range of occupations in the field of renewable energy and energy conservation. Curriculum development was by teams of Saint Francis University Faculty in the Business Administration and Science Departments and industry experts. Students seeking undergraduate and graduate degrees are able to enroll in courses offered within these departments which will combine theory and hands-on training in the various elements of wind power development. For example, the business department curriculum areas include economic modeling, finance, contracting, etc. The science areas include meteorology, energy conversion and projection, species identification, habitat protection, field data collection and analysis, etc.

  13. Participatory urban renewal

    Directory of Open Access Journals (Sweden)

    Drago Kos

    2005-01-01

    Full Text Available The article consists of two parts. The first deals with the theoretical framework of urban rehabilitation. Literature provides the basis for a conclusion, which is that the key issue in rehabilitation projects is legitimate negotiation of various interests between participating individuals and institutions. In the second part this presentation and analyses of events that took place at the urban design workshop organised within the framework of the research project Renewal of housing estates in Ljubljana, provide experiential confirmation of the starting thesis. We established that the directly involved residents were willing to actively participate in rehabilitation procedures, however the process is never triggered, because of insufficient capacities in institutional frameworks. In conclusion several real proposals are shown, namely, how to surmount obstacles in urban rehabilitation and especially in larger housing estates built after World War 2.

  14. Renewal of radiological equipment.

    Science.gov (United States)

    2014-10-01

    In this century, medical imaging is at the heart of medical practice. Besides providing fast and accurate diagnosis, advances in radiology equipment offer new and previously non-existing options for treatment guidance with quite low morbidity, resulting in the improvement of health outcomes and quality of life for the patients. Although rapid technological development created new medical imaging modalities and methods, the same progress speed resulted in accelerated technical and functional obsolescence of the same medical imaging equipment, consequently creating a need for renewal. Older equipment has a high risk of failures and breakdowns, which might cause delays in diagnosis and treatment of the patient, and safety problems both for the patient and the medical staff. The European Society of Radiology is promoting the use of up-to-date equipment, especially in the context of the EuroSafe Imaging Campaign, as the use of up-to-date equipment will improve quality and safety in medical imaging. Every healthcare institution or authority should have a plan for medical imaging equipment upgrade or renewal. This plan should look forward a minimum of 5 years, with annual updates. Teaching points • Radiological equipment has a definite life cycle span, resulting in unavoidable breakdown and decrease or loss of image quality which renders equipment useless after a certain time period.• Equipment older than 10 years is no longer state-of-the art equipment and replacement is essential. Operating costs of older equipment will be high when compared with new equipment, and sometimes maintenance will be impossible if no spare parts are available.• Older equipment has a high risk of failure and breakdown, causing delays in diagnosis and treatment of the patient and safety problems both for the patient and the medical staff.• Every healthcare institution or authority should have a plan for medical imaging equipment upgrade or replacement. This plan should look forward a

  15. Renewable Energy in European Regions

    NARCIS (Netherlands)

    Krozer, Yoram

    2012-01-01

    The regional dynamics of energy innovation, in particular the shift from fossil fuels to renewable energy in the EU, is discussed within the framework of neo-Schumpeterian theory. The EU’s 4.2% average annual growth in renewable energy production in the last decade has been accompanied by diverging

  16. Business development in renewable energy

    NARCIS (Netherlands)

    Krozer, Yoram; Visa, Ion

    2014-01-01

    This paper discusses how to foster development of renewable energy business. Factors that impede or enhance renewable energy in the EU 27 member states in the period 1998–2008 are analyzed. Nine factors are considered: population density, production output and energy sector output to indicate market

  17. PYRAMID LAKE RENEWEABLE ENERGY PLAN

    Energy Technology Data Exchange (ETDEWEB)

    HIGH DESERT GEOCULTURE, LLC

    2009-06-06

    The Pyramid Lake Renewable Energy Plan covers these areas: energy potential (primarily focusing on geothermal resource potential, but also more generally addressing wind energy potential); renewable energy market potential; transmission system development; geothermal direct use potential; and business structures to accomplish the development objectives of the Pyramid Lake Paiute Tribe.

  18. Renewal Processes and Repairable Systems

    NARCIS (Netherlands)

    2003-01-01

    In this thesis we discuss the following topics: 1. Renewal reward processes The marginal distributions of renewal reward processes and its version, which we call in this thesis instantaneous reward processes, are derived. Our approach is based on the theory of point processes, especially Poisson

  19. Renewable energies: public policy challenges

    International Nuclear Information System (INIS)

    Grazi, Laure; Souletie, Arthur

    2016-03-01

    Renewable energy sources (RES) are low-carbon energies available right within our borders, and as such can be of great value in addressing the challenges of climate change and energy security. In 2014, renewable energies accounted for 14.6% of France's gross final energy consumption. The French Energy Transition Act for Green Growth sets renewables targets of 23% and 32% as a share of gross final energy consumption by 2020 and 2030, respectively. However, renewable energies are still more costly than conventional energies. A significant share of this additional cost is borne by energy consumers, particularly in the form of energy taxation and biofuels blending obligations. Public aid is also provided to support heat production from renewable energy sources (RES-H). The two most significant aids available today are the Energy Transition Tax Credit (CITE) and the Heat Fund. Comparing the various types of renewable energies shows sharp disparities in terms of the cost of avoiding one tonne of CO 2 , which ranges from euros 59 to more than euros 500 for electricity production it follows that the cost of the energy transition is likely to vary significantly depending on which renewable energy sources are pushed to the fore. The combustion of biomass for heat production appears to offer an economically efficient way to reduce CO 2 emissions. Of the various renewable technologies available for the production of electricity (with the exception of hydropower, which was excluded from the scope of this study), onshore wind power is the least costly

  20. Renewable Energy Education in India

    Science.gov (United States)

    Bajpai, Shrish; Kidwai, Naimur Rahman

    2017-01-01

    The issue of renewable energy sources that have great potential to give solutions to the longstanding energy problems of India has been considered. It has been stated that renewable energy sources are an important part of India's plan to increase energy security and provide new generation with ample job opportunities. India's plans to move towards…

  1. 75 FR 26919 - Charter Renewals

    Science.gov (United States)

    2010-05-13

    ...: Notice of Renewal of the Advisory Committee on Commercial Remote Sensing Charter. SUMMARY: In accordance... Commercial Remote Sensing (ACCRES) is in the public interest in connection with the performance of duties imposed on the Department by law. The ACCRES Charter was renewed on April 1, 2010. SUPPLEMENTARY...

  2. Renewables in Global Energy Supply

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2007-07-01

    Renewable energies are essential contributors to the energy supply portfolio as they contribute to world energy supply security, reducing dependency on fossil fuel resources, and provide opportunities for mitigating greenhouse gases. Differences in definition and lack of adequate data complicated the discussion between participants on these key issues. The International Energy Agency believes that this fact sheet can be of use to all to facilitate the debate on the past, current and future place and role of renewables in total energy supply. Our goal is to present as objectively as possible the main elements of the current renewables energy situation. The definitions and coverage of national statistics vary between countries and organisations. In this fact sheet, the renewables definition includes combustible renewables and waste (CRW), hydro, geothermal, solar, wind, tide and wave energy.

  3. New renewables - a business challenge

    International Nuclear Information System (INIS)

    Jochum, G.

    2004-01-01

    This article takes a look at the increased use of renewable forms of energy and, in particular, the so-called 'new renewables' that are the subject of discussion in Europe and Switzerland. The wide divergence between the political and economical viewpoints concerning renewables is examined and the question is posed on how political desires and economical sense can be brought closer together. Questions concerning the public acceptance of various forms of energy are looked at and the expectations placed on renewable forms of energy are commented on. Criteria for models of promotion are listed including CO 2 emissions, technology and cost efficiency, marketing aspects and flexibility. Also, aspects concerning plausibility, fairness and responsibility are looked at. A model named 'Swiss Renewables Model' is proposed and its efficiency, functionality and financing are discussed

  4. The potential of renewable energies

    International Nuclear Information System (INIS)

    Glubrecht, H.

    1998-01-01

    If one compares the progress in research and development of renewable energy applications with the finding which has been granted to these activities during the 23 years after the first oil shock, one cannot but be very impressed. It is indicated in this paper hoe comprehensive the potential of renewable energy is. One should take into account that the methods described form a broad interdisciplinary field in contrast to fossil and nuclear technologies. From technical point of view the present and future energy demand can be met by the broad spectrum of renewable energies in combination with energy conservation. Many of these techniques are already economically competitive: solar architecture, wind energy, hydropower, low temperature heat production, photovoltaic for remote areas, various types of biomass application, geothermal energy although not exactly renewable. The future of renewable energies will depend on opening markets for these techniques

  5. Somerset County Renewable Energy Initiative

    Energy Technology Data Exchange (ETDEWEB)

    Katula, Denise [County of Somerset, Somervile, NJ (United States)

    2014-05-07

    The County of Somerset, New Jersey, through the Somerset County Improvement Authority (SCIA), applied Federal funding through the U.S. Department of Energy to will apply project funds to buy-down the capital costs of equipment associated with the installation of solar photovoltaic (PV) systems at two sites owned by the County. This Renewable Energy Initiative allows the County to take advantage of clean renewable energy, without any adverse debt impacts, and at a price that results in operating budget savings beyond what is presently available in the marketplace. This project addressed the objectives of the Office of Energy Efficiency and Renewable Energy by making the acquisition of renewable energy more affordable for the County, thereby, encouraging other counties and local units to develop similar programs and increase the deployment of solar energy technologies. The two sites that were funded by the DOE grant are part of a much larger, ambitious, and unique renewable energy project, described in the next section.

  6. Renewal-anomalous-heterogeneous files

    International Nuclear Information System (INIS)

    Flomenbom, Ophir

    2010-01-01

    Renewal-anomalous-heterogeneous files are solved. A simple file is made of Brownian hard spheres that diffuse stochastically in an effective 1D channel. Generally, Brownian files are heterogeneous: the spheres' diffusion coefficients are distributed and the initial spheres' density is non-uniform. In renewal-anomalous files, the distribution of waiting times for individual jumps is not exponential as in Brownian files, yet obeys: ψ α (t)∼t -1-α , 0 2 >, obeys, 2 >∼ 2 > nrml α , where 2 > nrml is the MSD in the corresponding Brownian file. This scaling is an outcome of an exact relation (derived here) connecting probability density functions of Brownian files and renewal-anomalous files. It is also shown that non-renewal-anomalous files are slower than the corresponding renewal ones.

  7. Modeling renewable energy company risk

    International Nuclear Information System (INIS)

    Sadorsky, Perry

    2012-01-01

    The renewable energy sector is one of the fastest growing components of the energy industry and along with this increased demand for renewable energy there has been an increase in investing and financing activities. The tradeoff between risk and return in the renewable energy sector is, however, precarious. Renewable energy companies are often among the riskiest types of companies to invest in and for this reason it is necessary to have a good understanding of the risk factors. This paper uses a variable beta model to investigate the determinants of renewable energy company risk. The empirical results show that company sales growth has a negative impact on company risk while oil price increases have a positive impact on company risk. When oil price returns are positive and moderate, increases in sales growth can offset the impact of oil price returns and this leads to lower systematic risk.

  8. Renewable energies for power generation

    International Nuclear Information System (INIS)

    Freris, L.; Infield, D.

    2009-01-01

    Power generation from renewable energy sources is different from power generation from classical energies (nuclear, thermal..). Therefore, the integration into the grid of the electricity supplied by renewable sources requires a deep thinking. The reason is that these power sources are controlled by variable elements, like wind, water and sun, which condition production. This book deals with the following aspects in detail: characteristics of classical and intermittent generators; grid balancing between supply and demand; conversion methods of renewable energies into electricity; power systems; privatizing of power generation and birth of new markets, in particular the 'green' power market; development of renewable energies thanks to technical advances. It gives a comprehensive overview of the present day available renewable energy sources for power generation. (J.S.)

  9. Electrochemical Approaches to Renewable Energy

    Science.gov (United States)

    Lobaccaro, Peter

    Renewable energy is becoming an increasingly important component of the world's energy supply as the threat of global warming continues to rise. There is a need to reduce the cost of this renewable energy and a future challenge to deal with the strain intermittent power sources like renewables place on the power grid. In this dissertation, electrochemistry is harnessed to address possible solutions to both of these issues. First, it is used to develop a low cost alternative photovoltaic material. Then, it is used to investigate the production of chemical fuel stocks which can be used for energy storage. In chapter 2, advances are made in the electrochemical deposition of indium (In) on molybdenum foil which enables the deposition of electronic-grade purity, continuous films with thicknesses in the micron range. As an example application, the electrodeposited In films are phosphorized via the thin-film vapor-liquid-solid growth method. The resulting poly-crystalline InP films display excellent optoelectronic quality, comparable to films grown from more standard vacuum deposition techniques. This demonstrates the versatility of the developed electrochemical deposition procedure. In the remaining chapters, renewable fuel production is investigated. First in chapter 3, molybdenum disulfide (MoS2) is examined as a catalyst for the hydrogen evolution reaction (HER). Typically, high-cost synthesized MoS2 is used as the catalyst because the pristine MoS 2 mineral is known to be a poor catalyst. The fundamental challenge with pristine MoS2 is the inert HER activity of the predominant (0001) basal surface plane. Here, we report a general thermal process in which the basal plane is texturized to increase the density of HER-active edge sites. The process generates high HER catalytic performance in pristine MoS 2 across various morphologies such as the bulk mineral, films composed of micron-scale flakes, and even films of a commercially-available spray of nanoflake MoS2. In

  10. Polymer biocomposites with renewable sources

    Directory of Open Access Journals (Sweden)

    S. Kuciel

    2010-07-01

    Full Text Available Nowadays production of natural biodegradable polymer composites is an important research topic on the stage of renewable sourcesimplementation instead of petrochemical sources. In this work, possibilities of processing biocomposites on the base on different types of biopolymers – polylactide (PLA, thermoplastic starch (TPS, polyhydroxybutyrate (PHB, cellulose acetate (CA - filled with natural fibers such as wood, kenaf, horse hair and nettle are presented. Large variety of natural fibers and their developed surface which increases adhesion to matrix makes them an attractive filler material. The fibers serve as reinforcement by giving strength and stiffness to the structure while the polymer matrix holds the fibers in place so that suitable structural composites can be made. Main physic-mechanical properties of natural fibers and biopolymers are presented. Modulus of elasticity and tensile strength increased with rising content of natural fibers in composite. The results show that biocomposites based on starch or PHB filled with kenaf fibers has the best mechanical properties. Modulus of elasticity achieves 10-12 GPa and tensile strength 50 MPa. This property can be interesting for packaging especially for fresh food like fruits or vegetables and for technical products with short-time life cycles. In future prospects, biocomposites based on biopolymers with a long time of decomposition can be interesting alternative as a construction material in automotive sectors.

  11. Spinodal Theory: A Common Rupturing Mechanism in Spinodal Dewetting and Surface Directed Phase Separation (Some Technological Aspects: Spatial Correlations and the Significance of Dipole-Quadrupole Interaction in Spinodal Dewetting)

    International Nuclear Information System (INIS)

    Singh, S.P.; Singh, S.P.

    2011-01-01

    The emerging structures in spinodal dewetting of thin nano films and spinodal decomposition of binary mixtures are found to be similar with certain differences attributed to the nonlinearities inherent in the wetting forces. This paper deals with the technological aspects of the spinodal processes by giving a brief account of the theory and to correlate the two phenomena termed as spinodal dewetting of thin nano films and surface-directed phase separation. The MC simulation micrographs at early stage of spinodal dewetting of a (linear) polymer film confined between two hard walls (using FENE potential between the beads on same chain and Morse potential between inter and intra chain beads) show similarities with surface-directed phase separation (using metropolis algorithm) in creation of holes. The spinodal dewetting is also criticized on the basis of global minimization of free energy emerging from dipole-quadrupole interactions. A novel molecular scale-driving mechanism coming from asymmetric interface formation in spinodal processes is also proposed. It can be believed that the modeling done with the films under confinement of two walls works as a classical mathematical Ansatz to the dipole-quadrupole interaction coming from quantum origins and giving rise to lateral interactions in the process reflecting a colossal behavior in thin nano films though weak in nature

  12. Spinodal Theory: A Common Rupturing Mechanism in Spinodal Dewetting and Surface Directed Phase Separation (Some Technological Aspects: Spatial Correlations and the Significance of Dipole-Quadrupole Interaction in Spinodal Dewetting

    Directory of Open Access Journals (Sweden)

    Satya Pal Singh

    2011-01-01

    Full Text Available The emerging structures in spinodal dewetting of thin nano films and spinodal decomposition of binary mixtures are found to be similar with certain differences attributed to the nonlinearities inherent in the wetting forces. This paper deals with the technological aspects of the spinodal processes by giving a brief account of the theory and to correlate the two phenomena termed as spinodal dewetting of thin nanofilms and surface-directed phase separation. The MC simulation micrographs at early stage of spinodal dewetting of a (linear polymer film confined between two hard walls (using FENE potential between the beads on same chain and Morse potential between inter and intra chain beads show similarities with surface-directed phase separation (using metropolis algorithm in creation of holes. The spinodal dewetting is also criticized on the basis of global minimization of free energy emerging from dipole-quadrupole interactions. A novel molecular scale-driving mechanism coming from asymmetric interface formation in spinodal processes is also proposed. It can be believed that the modeling done with the films under confinement of two walls works as a classical mathematical ansatz to the dipole-quadrupole interaction coming from quantum origins and giving rise to lateral interactions in the process reflecting a colossal behavior in thin nano films though weak in nature.

  13. Separate Developmental Programs for HLA-A and -B Cell Surface Expression during Differentiation from Embryonic Stem Cells to Lymphocytes, Adipocytes and Osteoblasts

    DEFF Research Database (Denmark)

    Sabir, Hardee J; Nehlin, Jan O; Qanie, Diyako

    2013-01-01

    -A, but not -B) is seen on some multipotent stem cells, and this raises the question how this is in other stem cells and how it changes during differentiation. In this study, we have used flow cytometry to investigate the cell surface expression of HLA-A and -B on human embryonic stem cells (hESC), human...... hematopoietic stem cells (hHSC), human mesenchymal stem cells (hMSC) and their fully-differentiated progenies such as lymphocytes, adipocytes and osteoblasts. hESC showed extremely low levels of HLA-A and no -B. In contrast, multipotent hMSC and hHSC generally expressed higher levels of HLA-A and clearly HLA......A major problem of allogeneic stem cell therapy is immunologically mediated graft rejection. HLA class I A, B, and Cw antigens are crucial factors, but little is known of their respective expression on stem cells and their progenies. We have recently shown that locus-specific expression (HLA...

  14. Capital renewal as a real option

    NARCIS (Netherlands)

    Reindorp, M.J.; Fu, M.C.

    2011-01-01

    We consider the timing of replacement of obsolete subsystems within an extensive, complex infrastructure. Such replacement action, known as capital renewal, must balance uncertainty about future profitability against uncertainty about future renewal costs. Treating renewal investments as real

  15. Battery storage for supplementing renewable energy systems

    Energy Technology Data Exchange (ETDEWEB)

    None, None

    2009-01-18

    The battery storage for renewable energy systems section of the Renewable Energy Technology Characterizations describes structures and models to support the technical and economic status of emerging renewable energy options for electricity supply.

  16. Renewable energy action plan. Policy action plan for promotion of renewable energy in the Czech Republic to 2010

    International Nuclear Information System (INIS)

    1999-08-01

    Energy efficiency and renewable energy production contribute to the three major goals of the national energy policy of the Czech Republic: overall competitiveness, security of supply; and environmental protection. Therefore, the Czech government promotes these two sustainable options. The Energy Policy White Paper, which is being developed at the time of writing (June 1999), will provide the general framework for the future role of energy efficiency and renewable energy in the Czech Republic. However, in addition, it is necessary to develop specific policies. The National Energy Efficiency Study aimed to support the Czech government in the formula tion of energy efficiency and renewable energy policy. The National Energy Efficiency Study has resulted in the following documents: (1) The Renewable Energy Action Plan (this report) addresses renewable energy production. The Energy Efficiency Action Plan focuses on the promotion of energy efficiency in end use (separate report; ECN-C--99-065). These two Action Plans provide policy makers in the Czech government with information on potentials, targets, budgets and recommended policy instruments. The core of the Action Plans is the list of concrete policy actions, ready for implementation; (2) The National Energy Efficiency Study NEES (separate report; ECN-C--99-063). This report is the background document to the two Action Plans. It contains detailed information on options and measures, potentials, barriers and policy instruments for energy efficiency and renewables. The main part is a detailed outline for a new energy efficiency and renewable policy. Also, it includes recommendations for financing schemes to overcome the invest ment constraints in the Czech Republic. Finally, a list of concrete projects is included to support project identification

  17. Vehicle Testing and Integration Facility; NREL (National Renewable Energy Laboratory)

    Energy Technology Data Exchange (ETDEWEB)

    None

    2015-03-02

    Engineers at the National Renewable Energy Laboratory’s (NREL’s) Vehicle Testing and Integration Facility (VTIF) are developing strategies to address two separate but equally crucial areas of research: meeting the demands of electric vehicle (EV) grid integration and minimizing fuel consumption related to vehicle climate control. Dedicated to renewable and energy-efficient solutions, the VTIF showcases technologies and systems designed to increase the viability of sustainably powered vehicles. NREL researchers instrument every class of on-road vehicle, conduct hardware and software validation for EV components and accessories, and develop analysis tools and technology for the Department of Energy, other government agencies, and industry partners.

  18. Building a sustainable market for renewables

    Energy Technology Data Exchange (ETDEWEB)

    Rader, N.

    1996-12-31

    Opinions regarding marketing approaches for electricity generation from renewable resources are presented in the paper. The Renewables Portfolio Standard of the California Public Utilities Commission is described. This system is based on renewable energy credits. Other marketing approaches, including surcharges, auctioned renewables credit, green pricing, and green marketing are also assessed. It is concluded that the Renewables Portfolio Standard creates a stable economic environment for the renewable energy industries.

  19. Separate developmental programs for HLA-A and -B cell surface expression during differentiation from embryonic stem cells to lymphocytes, adipocytes and osteoblasts.

    Directory of Open Access Journals (Sweden)

    Hardee J Sabir

    Full Text Available A major problem of allogeneic stem cell therapy is immunologically mediated graft rejection. HLA class I A, B, and Cw antigens are crucial factors, but little is known of their respective expression on stem cells and their progenies. We have recently shown that locus-specific expression (HLA-A, but not -B is seen on some multipotent stem cells, and this raises the question how this is in other stem cells and how it changes during differentiation. In this study, we have used flow cytometry to investigate the cell surface expression of HLA-A and -B on human embryonic stem cells (hESC, human hematopoietic stem cells (hHSC, human mesenchymal stem cells (hMSC and their fully-differentiated progenies such as lymphocytes, adipocytes and osteoblasts. hESC showed extremely low levels of HLA-A and no -B. In contrast, multipotent hMSC and hHSC generally expressed higher levels of HLA-A and clearly HLA-B though at lower levels. IFNγ induced HLA-A to very high levels on both hESC and hMSC and HLA-B on hMSC. Even on hESC, a low expression of HLA-B was achieved. Differentiation of hMSC to osteoblasts downregulated HLA-A expression (P = 0.017. Interestingly HLA class I on T lymphocytes differed between different compartments. Mature bone marrow CD4(+ and CD8(+ T cells expressed similar HLA-A and -B levels as hHSC, while in the peripheral blood they expressed significantly more HLA-B7 (P = 0.0007 and P = 0.004 for CD4(+ and CD8(+ T cells, respectively. Thus different HLA loci are differentially regulated during differentiation of stem cells.

  20. Renewables 2013. Global Status Report

    Energy Technology Data Exchange (ETDEWEB)

    Sawin, J. L. [and others

    2013-07-01

    Renewable energy markets, industries, and policy frameworks have evolved rapidly in recent years. The Renewables Global Status Report provides a comprehensive and timely overview of renewable energy market, industry, investment, and policy developments worldwide. It relies on the most recent data available, provided by many contributors and researchers from around the world, all of which is brought together by a multi-disciplinary authoring team. The report covers recent developments, current status, and key trends; by design, it does not provide analysis or forecasts. This latest Renewables Global Status Report saw: a shift in investment patterns that led to a global decrease in clean energy investment; continuing growth in installed capacity due to significant technology cost reductions and increased investment in developing countries; renewables progressively supplementing established electricity systems, demonstrating that the implementation of suitable policies can enable the successful integration of higher shares of variable renewables; and the emergence of integrated policy approaches that link energy efficiency measures with the implementation of renewable energy technologies.

  1. Developing Government Renewable Energy Projects

    Energy Technology Data Exchange (ETDEWEB)

    Kurt S. Myers; Thomas L. Baldwin; Jason W. Bush; Jake P. Gentle

    2012-07-01

    The US Army Corps of Engineers has retained Idaho National Laboratory (INL) to conduct a study of past INL experiences and complete a report that identifies the processes that are needed for the development of renewable energy projects on government properties. The INL has always maintained expertise in power systems and applied engineering and INL’s renewable energy experiences date back to the 1980’s when our engineers began performing US Air Force wind energy feasibility studies and development projects. Over the last 20+ years of working with Department of Defense and other government agencies to study, design, and build government renewable projects, INL has experienced the do’s and don’ts for being successful with a project. These compiled guidelines for government renewable energy projects could include wind, hydro, geothermal, solar, biomass, or a variety of hybrid systems; however, for the purpose of narrowing the focus of this report, wind projects are the main topic discussed throughout this report. It is our thought that a lot of what is discussed could be applied, possibly with some modifications, to other areas of renewable energy. It is also important to note that individual projects (regardless the type) vary to some degree depending on location, size, and need but in general these concepts and directions can be carried over to the majority of government renewable energy projects. This report focuses on the initial development that needs to occur for any project to be a successful government renewable energy project.

  2. renewables 2011 - Global status report

    International Nuclear Information System (INIS)

    Sawin, Janet L.; Martinot, Eric; Barnes, Douglas; Martinot, Eric; McCrone, Angus; Roussell, Jodie; Sawin, Janet L.; Sims, Ralph; Sonntag-O'Brien, Virginia; Adib, Rana; Skeen, Jonathan; Musolino, Evan; Riahi, Lily; Mastny, Lisa

    2011-01-01

    Changes in renewable energy markets, investments, industries, and policies have been so rapid in recent years that perceptions of the status of renewable energy can lag years behind the reality. This report captures that reality and provides a unique overview of renewable energy worldwide as of early 2011. The report covers both current status and key trends; by design, it does not provide analysis or forecast the future. Global energy consumption rebounded in 2010 after an overall downturn in 2009. Renewable energy, which experienced no downturn in 2009, continued to grow strongly in all end-use sectors - power, heat and transport - and supplied an estimated 16% of global final energy consumption. Renewable energy accounted for approximately half of the estimated 194 gigawatts (GW) of new electric capacity added globally during the year. Renewables delivered close to 20% of global electricity supply in 2010, and by early 2011 they comprised one quarter of global power capacity from all sources. In several countries, renewables represent a rapidly growing share of total energy supply, including heat and transport

  3. Mitigation of global warming through renewable biomass

    International Nuclear Information System (INIS)

    Dhillon, R.S.; Wuehlisch, George von

    2013-01-01

    Rising level of atmospheric CO 2 and consequent global warming is evident. Global surface temperature have already increased by 0.8 °C over the 20th century and is projected to increase by 1.4–5.8 °C during the twenty-first century. The global warming will continue till atmospheric concentrations of the major greenhouse gases are stabilized. Among them, CO 2 is mainly responsible and is expected to account for about 60% of the warming over the next century. This study reviews advances on causes and consequences of global climate change and its impact on nature and society. Renewable biomass has tremendous potential to mitigate the global warming. Renewable biomass is expected to play a multifunctional role including food production, source of energy and fodder, biodiversity conservation, yield of goods and services to the society as well as mitigation of the impact of climate change. The review highlights the different management and research strategies in forestry, agriculture, agroforestry and grasslands to mitigate the global warming. -- Highlights: ► Rising level of atmospheric CO 2 and consequent global warming is evident. ► CO 2 is mainly responsible for global warming. ► Global temperature is predicted to increase by 1.4–5.8 °C during 21st century. ► Renewable biomass has great potential to mitigate the global warming

  4. Marine Renewable Energy Center

    Energy Technology Data Exchange (ETDEWEB)

    Vigeant, Paul [Univ. of Massachusetts, Dartmouth, MA (United States); Miller, John [Univ. of Massachusetts, Dartmouth, MA (United States); Howes, Brian [Univ. of Massachusetts, Dartmouth, MA (United States); McGowan, Jon G. [Univ. of Massachusetts, Amherst, MA (United States); Baldwin, Kenneth [Univ. of New Hampshire, Durham, NH (United States); Grilli, Annette [Univ. of Rhode Island, Kingston, RI (United States); Terray, Eugene [Woods Hole Oceanographic Inst., Woods Hole, MA (United States)

    2013-10-08

    Project Goals: The funding provided by this contract supported the following activities: A) Test Site Development; B) Seed Grant Funded Technology Development; C) Stakeholder Activities The first year of funding was dedicated to the formation of the NE MREC University Consortium which was comprised of University of Massachusetts Dartmouth (UMD) and Amherst (UMA), Massachusetts Institute of Technology (MIT), Woods Hole Oceanographic Institution (WHOI), University of New Hampshire (UNH), and the University of Rhode Island (URI). The consortium worked together to encourage research and promote benefits of obtaining energy from ocean wind, waves, tides and currents. In addition, NE MREC’s goal was to fund projects aimed at potential test sites with the first year funding going to studies of the potential for tidal device testing in Muskeget Channel, at the General Sullivan Bridge in New Hampshire, and for wave device testing at the proposed National Offshore Renewable Energy Innovation Zone (NOREIZ) located off the Massachusetts coast. The project spanned 4.5 years and addressed three specific tasks that are interrelated but also served as independent investigations.

  5. Renewables 2005. Global status report

    International Nuclear Information System (INIS)

    2005-01-01

    This report provides an overview of the status of renewable energy worldwide in 2005. It covers markets, investments, industries, policies, and rural (off-grid) renewable energy in developing countries. By design, the report does not provide analysis, recommendations, or conclusions. An extensive research and review process over several months involving more than 100 researchers and contributors has kept inaccuracies to a minimum. REN21 sees this report as the beginning of an active exchange of views and information. This report reveals some surprising facts about renewable energy, many reflecting strong growth trends and increasing significance relative to conventional energy. (au)

  6. Renewables 2005. Global status report

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2005-07-01

    This report provides an overview of the status of renewable energy worldwide in 2005. It covers markets, investments, industries, policies, and rural (off-grid) renewable energy in developing countries. By design, the report does not provide analysis, recommendations, or conclusions. An extensive research and review process over several months involving more than 100 researchers and contributors has kept inaccuracies to a minimum. REN21 sees this report as the beginning of an active exchange of views and information. This report reveals some surprising facts about renewable energy, many reflecting strong growth trends and increasing significance relative to conventional energy. (au)

  7. Renewables 2005 - Global status report

    International Nuclear Information System (INIS)

    Martinot, Eric

    2005-01-01

    This report provides an overview of the status of renewable energy worldwide in 2005. It covers markets, investments, industries, policies, and rural (off-grid) renewable energy in developing countries. By design, the report does not provide analysis, recommendations, or conclusions. An extensive research and review process over several months involving more than 100 researchers and contributors has kept inaccuracies to a minimum. REN21 sees this report as the beginning of an active exchange of views and information. This report reveals some surprising facts about renewable energy, many reflecting strong growth trends and increasing significance relative to conventional energy

  8. Separation of microplastics from a coastal soil and their surface microscopic features%滨海潮滩土壤中微塑料的分离及其表面微观特征

    Institute of Scientific and Technical Information of China (English)

    周倩; 章海波; 周阳; 李远; 薛勇; 付传城; 涂晨; 骆永明

    2016-01-01

    微塑料(<5 mm)作为海岸带地区的新型污染物正越来越受到关注.本研究以我国河北省曹妃甸围填海区潮滩土壤为例,采用自行改进设计的连续流动-气浮分离一体化装置,有效分离和提取了潮滩土壤样品中微塑料,并结合扫描电子显微镜-能谱仪(SEM-EDS)对微塑料表面的微观特性进行了表征.研究结果表明,供试土壤中微塑料丰度达到317 n/500 g(其中n表示微塑料个数),平均粒径为1.56±0.63 mm,其中<1 mm的微塑料占49.8%;微塑料丰度上整体呈现随粒径变小而增加的趋势.在土壤中分离到碎片、颗粒、纤维和薄膜四类微塑料,其中,黑色碎片类微塑料为首次报道的类型.颗粒类微塑料丰度最大但平均粒径最小.土壤中微塑料表面均有不同程度的风化痕迹,具有不同形态和大小的微孔结构.在部分微塑料中还发现其表面附着稳定的铁氧化物.未来需要深入研究了解基于微塑料表面特性的污染物结合机制、生物积累与生态毒性,尤其更需关注丰度较高、颗粒更细的<1 mm的这部分微塑料(MP1).%Microplastics (<5 mm) are emerging pollutants in the coastal zone and are of worldwide concern.Previous studies have shown the importance of surface features of microplastics on the adsorption and transport of chemical pollutants in the ocean and coastal environment.The objective of this study was therefore to characterize the surface properties of the microplastic samples from a reclamation area polluted by plastic debris in Chaofeidian,Hebei Province.A surface (0-2 cm) soil composite sample was collected from several square plots each with an area of 1 m×l m.The microplastics were separated in two steps.Firstly,500 g (dry weight) soil sample was reduced to <100 g soil which contained most of the microplastics using continuous air-flow flotation separation apparatus designed by our own group.Secondly,the microplastics were separated from the

  9. Renewable, ethical? Assessing the energy justice potential of renewable electricity

    Directory of Open Access Journals (Sweden)

    Aparajita Banerjee

    2017-08-01

    Full Text Available Energy justice is increasingly being used as a framework to conceptualize the impacts of energy decision making in more holistic ways and to consider the social implications in terms of existing ethical values. Similarly, renewable energy technologies are increasingly being promoted for their environmental and social benefits. However, little work has been done to systematically examine the extent to which, in what ways and in what contexts, renewable energy technologies can contribute to achieving energy justice. This paper assesses the potential of renewable electricity technologies to address energy justice in various global contexts via a systematic review of existing studies analyzed in terms of the principles and dimensions of energy justice. Based on publications including peer reviewed academic literature, books, and in some cases reports by government or international organizations, we assess renewable electricity technologies in both grid integrated and off-grid use contexts. We conduct our investigation through the rubric of the affirmative and prohibitive principles of energy justice and in terms of its temporal, geographic, socio-political, economic, and technological dimensions. Renewable electricity technology development has and continue to have different impacts in different social contexts, and by considering the different impacts explicitly across global contexts, including differences between rural and urban contexts, this paper contributes to identifying and understanding how, in what ways, and in what particular conditions and circumstances renewable electricity technologies may correspond with or work to promote energy justice.

  10. Renewables 2010 - Global status report

    International Nuclear Information System (INIS)

    Sawin, Janet L.; Martinot, Eric; Sonntag-O'Brien, Virginia; McCrone, Angus; Roussell, Jodie; Barnes, Douglas; Flavin, Christopher; Mastny, Lisa; Kraft, Diana; Wang, Shannon; Ellenbeck, Saskia; Ilieva, Lili; Griebenow, Christof; Adib, Rana; Lempp, Philippe; Welker, Bettina

    2010-01-01

    Changes in renewable energy markets, investments, industries, and policies have been so rapid in recent years that perceptions of the status of renewable energy can lag years behind the reality. This report captures that reality and provides a unique overview of renewable energy worldwide as of early 2010. The report covers both current status and key trends. By design, the report does not provide analysis, discuss current issues, or forecast the future. Many of the trends reflect the increasing significance of renewable energy relative to conventional energy sources (including coal, gas, oil, and nuclear). By 2010, renewable energy had reached a clear tipping point in the context of global energy supply. Renewables comprised fully one quarter of global power capacity from all sources and delivered 18 percent of global electricity supply in 2009. In a number of countries, renewables represent a rapidly growing share of total energy supply-including heat and transport. The share of households worldwide employing solar hot water heating continues to increase and is now estimated at 70 million households. And investment in new renewable power capacity in both 2008 and 2009 represented over half of total global investment in new power generation. Trends reflect strong growth and investment across all market sectors-power generation, heating and cooling, and transport fuels. Grid-connected solar PV has grown by an average of 60 percent every year for the past decade, increasing 100-fold since 2000. During the past five years from 2005 to 2009, consistent high growth year-after-year marked virtually every other renewable technology. During those five years, wind power capacity grew an average of 27 percent annually, solar hot water by 19 percent annually, and ethanol production by 20 percent annually. Biomass and geothermal for power and heat also grew strongly. Much more active policy development during the past several years culminated in a significant policy milestone

  11. Action plan for renewable energy sources

    International Nuclear Information System (INIS)

    2000-03-01

    energy sources in relation to other energy sources. The objective in the long term is to make them as competitive as possible in the open energy market. Among those measures of crucial importance included in the Action Plan, we can mention development and commercialisation of new technology as well as several financial measures, of which taxation and investment aid are considered to have the greatest effect. In addition, the Action Plan presents several administrative measures for the promotion of renewable energy sources. A separate assessment of the environmental impact of the Action Plan has been made resulting in an environmental impact statement (EIS) that contains a detailed account of the environmental impacts of the use of renewable energy sources and the use of peat in energy production. The most important environmental impact of the implementation of the Action Plan will be a reduction in greenhouse gas emissions. As a result of the intensified measures to be taken in accordance with the Action Plan, carbon dioxide emissions are estimated to be reduced at least by 2 million tons per year compared with the outlook presented in the Energy Strategy. Further, the use of waste, which otherwise would have been transported to tips, in energy production is estimated to reduce methane emissions by 1 million ton per year (C0 2 equivalent). The reduction might be even much bigger in the next few years. To ensure that the objectives of the Action Plan will be achieved, the contribution by the State (tax subsidies, investment aid and other forms of aid) should be approx. FIM 500 million on an average per year in the next ten years. In 1998, the State's contribution exceeded FIM 300 million. Further, financing amounting to approx. FIM 200 million is channelled to the research on and the development of energy production technology, which in the future to a larger extent than now will be channelled to the development of such forms of energy production technology that are using

  12. Financing of Renewable Energy Projects

    International Nuclear Information System (INIS)

    Santizo, Rodolfo; Berganza, Jose

    2000-01-01

    The paper describes the role of the Banco Centroamericano de Integracion Economica in financing renewable energy projects in Central America. Also decribes the different financing modes to the goverment and private sectors

  13. Nuclear energy and renewable energies

    International Nuclear Information System (INIS)

    1994-01-01

    The nuclear energy and the renewable energies namely: solar energy, wind energy, geothermal energy and biomass are complementary. They are not polluting and they are expected to develop in the future to replace the fossil fuels

  14. VT Renewable Energy Sites - Hydroelectric

    Data.gov (United States)

    Vermont Center for Geographic Information — (Link to Metadata) The Renewable Energy Atlas of Vermont and this dataset were created to assist town energy committees, the Clean Energy Development Fund and other...

  15. VT Renewable Energy Sites - Geothermal

    Data.gov (United States)

    Vermont Center for Geographic Information — (Link to Metadata) The Renewable Energy Atlas of Vermont and this dataset were created to assist town energy committees, the Clean Energy Development Fund and other...

  16. VT Renewable Energy Sites - Landfills

    Data.gov (United States)

    Vermont Center for Geographic Information — (Link to Metadata) The Renewable Energy Atlas of Vermont and this dataset were created to assist town energy committees, the Clean Energy Development Fund and other...

  17. VT Renewable Energy Sites - Wind

    Data.gov (United States)

    Vermont Center for Geographic Information — (Link to Metadata) The Renewable Energy Atlas of Vermont and this dataset were created to assist town energy committees, the Clean Energy Development Fund and other...

  18. Renewable energies in United Kingdom

    International Nuclear Information System (INIS)

    Baize, T.

    1993-01-01

    An evaluation of research and development policy in United Kingdom on renewable energy sources is presented with economical studies (short or long term profitability), engaged programs and electric production. (A.B.). refs. tabs

  19. Which leadership for renewable energies?

    International Nuclear Information System (INIS)

    Chaumien, Marielle

    2016-02-01

    This publication first outlines that France is late in deploying renewable energies by 2020. It comments the application of the Energy multi-year plan (PPE), evokes the content of a report by the French Court of Auditors about costs and means of implementation of transition (with notably the issue of maintenance of nuclear plants). It also shows that European Union is not a leader in renewable energies any more, that some European countries are changing sides, that figures and trends must be carefully compared with those in the field of fossil and nuclear energies, that all energies are not all the same, that jobs and system integration are also important, that investments and attractiveness of countries in renewable energies must be assessed, and that a mobilisation on small scale and consumer-based renewable energies is required. Ten recommendations are made for France to support the EU leadership development

  20. VT Renewable Energy Sites - Solar

    Data.gov (United States)

    Vermont Center for Geographic Information — (Link to Metadata) The Renewable Energy Atlas of Vermont and this dataset were created to assist town energy committees, the Clean Energy Development Fund and other...

  1. Renewable energy in the EU

    International Nuclear Information System (INIS)

    Lambert, Allan; Myers, Stephen; Trow, Stuart

    1998-05-01

    Contains Executive Summary and Chapters on: Overview of European Renewable Energy; Austria; Belgium; Denmark; Finland; France; Germany; Greece; Ireland; Italy; Luxembourg; The Netherlands; Portugal; Spain; Sweden; The United Kingdom. (Author)

  2. Nanostructured Materials for Renewable Energy

    Energy Technology Data Exchange (ETDEWEB)

    None

    2009-11-01

    This factsheet describes a research project whose overall objective is to advance the fundamental understanding of novel photoelectronic organic device structures integrated with inorganic nanostructures, while also expanding the general field of nanomaterials for renewable energy devices and systems.

  3. Renewables Global Futures Report: Great debates towards 100% renewable energy

    International Nuclear Information System (INIS)

    Teske, Sven; Fattal, Alex; Lins, Christine; Hullin, Martin; Williamson, Laura E.

    2017-01-01

    The first version of REN21's Renewables Global Futures Report (GFR) published in January 2013 identified a panorama of likely future debates related to the renewable energy transition. As a reflection of the wide range of contemporary thinking by the many experts interviewed for the report, it did not present just one vision of the future but rather a 'mosaic' of insights. Given the positive feedback in response to the first edition, a new edition has been prepared, continuing where the last one left off. The objective of this report is to gather opinions about the feasibility of a 100% renewable energy future, and the macro-economic impacts it would entail. In so doing, the report reflects on the debates of 2013, and tracks their evolution to the present time. Some remain, some have changed, some have been overtaken by progress, and new ones have arisen. They are summarised here as the Great Debates in renewable energy. The questionnaire for the survey was developed in close cooperation between the REN21 Secretariat, the Institute for Sustainable Future (ISF) of the University of Technology Sydney/Australia (UTS) and the Institute for Advanced Sustainability Studies (IASS) in Potsdam/Germany. It covered the following topics: 1. How much renewables?; 2. Power sector; 3. Heating and cooling; 4. Transport; 5. Storage; 6. Demand-side management and energy efficiency; 7. Integration of sectors; 8. Macro-economic considerations; 9. Technology and costs; 10. Policy; 11. Cities; 12. Distributed renewable energy/energy access; 13. Barriers/challenges/enablers. 114 experts were interviewed in total; the average interview time was approximately one hour. The interviews were conducted between May and October 2016. The questionnaire was also mirrored in an online version and used both by interviewers and interviewees to record the interview process. Interviewees were selected from the following regions: Africa, Australia and Oceania, China, Europe, India, Japan, Latin America

  4. Catalytic Gas-Phase Production of Lactide from Renewable Alkyl Lactates.

    Science.gov (United States)

    De Clercq, Rik; Dusselier, Michiel; Makshina, Ekaterina; Sels, Bert F

    2018-03-12

    A new route to lactide, which is a key building block of the bioplastic polylactic acid, is proposed involving a continuous catalytic gas-phase transesterification of renewable alkyl lactates in a scalable fixed-bed setup. Supported TiO 2 /SiO 2 catalysts are highly selective to lactide, with only minimal lactide racemization. The solvent-free process allows for easy product separation and recycling of unconverted alkyl lactates and recyclable lactyl intermediates. The catalytic activity of TiO 2 /SiO 2 catalysts was strongly correlated to their optical properties by DR UV/Vis spectroscopy. Catalysts with high band-gap energy of the supported TiO 2 phase, indicative of a high surface spreading of isolated Ti centers, show the highest turnover frequency per Ti site. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  5. Panorama 2011: Ocean renewable energies

    International Nuclear Information System (INIS)

    Demoulin, P.; Vinot, S.

    2011-01-01

    Our society is looking increasingly to renewable energy sources in the face of the energy and environmental challenges with which it is grappling. As far as ocean renewable energies are concerned, a wide range of technologies is currently being experimented with, including wind power and energy derived from waves and tidal currents. They are all at varying levels of maturity, and bring with them very different technical and economic challenges. (author)

  6. GRENADA. Renewables Readiness Assessment 2012

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2012-07-01

    Grenada, like many Caribbean islands, is dependent on costly oil imports for its energy needs, including the generation of electricity. The transition to renewable energy could potentially support price reductions and improve the overall competitiveness of key sectors of the economy, particularly tourism. This report provides facts and analysis to support the country's discussion on ways to move forward with the renewable energy agenda. IRENA is ready to provide support in the implementation of the actions identified in this report.

  7. The renewable energies: the landscape

    International Nuclear Information System (INIS)

    Acket, C.; Bacher, P.

    2005-03-01

    If one takes into account the hydroelectric power, the France is the first european country in the renewable energies domain. The position is also honorable concerning the wood energy. Meanwhile, for the solar and wind energy, France is late. To discuss this debate, the authors bring together today data on the renewable energies, offer some proposals for the next 50 years taking into account the reduction of greenhouse gases emission for 2050. (A.L.B.)

  8. Renewable Energy Education in India

    OpenAIRE

    Bajpai Shrish; Kidwai Naimur Rahman

    2017-01-01

    The issue of renewable energy sources that have great potential to give solutions to the longstanding energy problems of India has been considered. It has been stated that renewable energy sources are an important part of India’s plan to increase energy security and provide new generation with ample job opportunities. India’s plans to move towards green technology and address environmental concerns associated with the country and the world have been characterized. The peculiarities of the ren...

  9. Local investment in renewable energies

    International Nuclear Information System (INIS)

    2003-11-01

    Although the vast majority of renewable energies projects are established by commercial developers, some of them are financed by ''ordinary citizens'' pooling together through different schemes. This is particularly frequent in Denmark and Germany, possibly a key reason for the continuous and so successful growth of various renewable energies sources in these countries. This guideline aims to define the term of local investment and provides examples of development and recommendations. (A.L.B.)

  10. Regional Integration of Renewable Energies

    International Nuclear Information System (INIS)

    Amador Guerra, J.; Dominguez Bravo, J.

    2000-01-01

    The aim of this report is to show how Energetic Planning and Territorial Policy should be working together for a better integration of Renewable Energies into Region. This Integration should to contemplate social, economic and environmental aspects of the territory. The report has been classified into 7 items: planning, energetic scenarios, technology transfer for Renewable Energies dissemination, barriers for this dissemination, environmental aspects, European Union Policy and Decision Support Systems (and specially GIS). (Author) 54 refs

  11. Renewable energies in the EU

    International Nuclear Information System (INIS)

    Heller, W.

    2008-01-01

    On January 23, 2008, the European Commission presented proposals in the form of a directive in an effort to give more specific shape to the objective adopted in the spring, i.e. to increase to 20% by 2020 the share of renewable energies in energy consumption in the Community. The proposal was to include legally binding goals for the overall share of renewable energy sources and the share of biofuels in the transport sector. The proposed directive on 'promoting the use of energy from renewable sources' calls upon each member state to ensure that its share of energy from renewable sources in the total energy consumption in 2020 at least corresponds to the target mentioned in Annex I Part A. In addition to the targets, the EU Commission charted a tentative course towards a minimum increase in the share of renewable energies in the period between 2011 and 2020. Finally, the member states are obliged to adopt national action plans. Unfortunately, the EU is missing an important target in its proposed directive: It should establish a framework for harmonized conditions promoting the use of renewable energies. One aspect to be welcomed is the introduction of a system of certificates of origin. It represents the entry, in principle, into a trading system with certificates of origin. The Green Package incorporates a wealth of new approaches. They will have to be tested and, if necessary, supplemented. Something else is evident, however: The directive established the foundations of a vast number of new regulations and red tape. (orig.)

  12. Renewable energy islands in Europe

    Energy Technology Data Exchange (ETDEWEB)

    Oestergaard, Iben [ed.

    1998-12-31

    This publication includes a compiled presentation of various aspects concerning the possible transformation of some European islands into renewable energy communities and these projects were presented by a selection of pioneer islands at the first European Seminar on Renewable Energy Islands, held on the Danish island of Samsoee, 29-30 June 1998. This issue has increased in importance with the presentation of the ambitious EU-White Paper: `Energy for the future: Renewable Sources of Energy` which was adopted in 1998. One of the key elements of the strategy for an accelerated implementation of renewable energy is to transform 100 localities within Europe into communities which are to be 100% self-sufficient with renewable energy before 2010. In line with this strategy, the Danish Government appointed the island of Samsoe towards the end of 1997 to be the first `official` Danish, renewable energy island. This is to serve as a demonstration project for other local communities, both in Denmark as well as in the rest Europe. Gothland, Madeira, Canary Islands, Cape Verde, Arki, Crete, Minorca and Orkney Islands were represented. Environmental advantages of wind, solar and wave power for distant island communities were indicated. Serious savings would be achieved by limitation of fossil fuel import and utilization of local resources. (EG)

  13. Simulation of hybrid renewable microgeneration systems for variable electricity prices

    International Nuclear Information System (INIS)

    Brandoni, C.; Renzi, M.; Caresana, F.; Polonara, F.

    2014-01-01

    This paper addresses a hybrid renewable system that consists of a micro-Combined Cooling Heat and Power (CCHP) unit and a solar energy conversion device. In addition to a traditional PV system, a High Concentrator Photovoltaic (HCPV) device, the design of which is suitable for building integration application, was also modelled and embedded in the hybrid system. The work identifies the optimal management strategies for the hybrid renewable system in an effort to minimise the primary energy usage, the carbon dioxide emissions and the operational costs for variable electricity prices that result from the day-ahead electricity market. An “ad hoc” model describes the performance of the HCPV module, PV and Internal Combustion Engine, whilst the other units were simulated based on their main characteristic parameters. The developed algorithm was applied to three different building typologies. The results indicate that the best configuration is the hybrid renewable system with PV, which can provide a yearly primary energy reduction of between 20% and 30% compared to separate production. The hybrid renewable system with HCPV becomes competitive with the PV technology when the level of solar radiation is high. - Highlights: • The paper addresses a hybrid renewable system that consists of a micro-CCHP unit and a solar energy conversion device. • Both PV and High Concentrator Photovoltaic (HCPV) systems have been modelled and embedded in the hybrid system. • The work identifies the optimal management strategies for variable electricity prices. • Hybrid renewable systems provide a yearly primary energy reduction of between 20% and 30% compared to separate production. • When the level of solar radiation is high, HCPV becomes competitive with the PV technology

  14. Surface molecular imprinting onto fluorescein-coated magnetic nanoparticlesvia reversible addition fragmentation chain transfer polymerization: A facile three-in-one system for recognition and separation of endocrine disrupting chemicals

    Science.gov (United States)

    Li, Ying; Dong, Cunku; Chu, Jia; Qi, Jingyao; Li, Xin

    2011-01-01

    In this study, we present a general protocol for the making of surface-imprinted magnetic fluorescence beads viareversible addition-fragmentation chain transfer polymerization. The resulting composites were characterized by X-ray diffraction analysis, transmission electron microscopy, scanning electron microscopy, fluorescence spectroscopy, Fourier transform infrared spectroscopy, and energy dispersive spectroscopy. The as-synthesized beads exhibited homogeneous polymer films (thickness of about 5.7 nm), spherical shape, high fluorescence intensity and magnetic property (Magnetization (Ms) = 3.67 emu g-1). The hybrids bind the original template 17β-estradiol with an appreciable selectivity over structurally related compounds. In addition, the resulting hybrids performed without obvious deterioration after five repeated cycles. This study therefore demonstrates the potential of molecularly imprinted polymers for the recognition and separation of endocrine disrupting chemicals.In this study, we present a general protocol for the making of surface-imprinted magnetic fluorescence beads viareversible addition-fragmentation chain transfer polymerization. The resulting composites were characterized by X-ray diffraction analysis, transmission electron microscopy, scanning electron microscopy, fluorescence spectroscopy, Fourier transform infrared spectroscopy, and energy dispersive spectroscopy. The as-synthesized beads exhibited homogeneous polymer films (thickness of about 5.7 nm), spherical shape, high fluorescence intensity and magnetic property (Magnetization (Ms) = 3.67 emu g-1). The hybrids bind the original template 17β-estradiol with an appreciable selectivity over structurally related compounds. In addition, the resulting hybrids performed without obvious deterioration after five repeated cycles. This study therefore demonstrates the potential of molecularly imprinted polymers for the recognition and separation of endocrine disrupting chemicals. Electronic

  15. U.S. regulatory requirements for nuclear plant license renewal: The B and W Owners Group License Renewal Program

    International Nuclear Information System (INIS)

    Staudinger, Deborah K.

    2004-01-01

    This paper discusses the current U.S. Regulatory Requirements for License Renewal and describes the Babcock and Wilcox Owners Group (B and WOG) Generic License Renewal Program (GLRP). The B and W owners, recognizing the need to obtain the maximum life for their nuclear generating units, embarked on a program to renew the licenses of the seven reactors in accordance with the requirements of the Atomic Energy Act of 1954 and further defined by Title 10 of the Code of Federal Regulation Part 54 (10 CFR 54). These reactors, owned by five separate utilities, are Pressurized Water Reactors (PWR) ranging in net rated capacity from approximately 800 to 900 MW. The plants, predominately constructed in the 70s, have USNRC Operating Licenses that expire between 2013 to 2017. (author)

  16. Steam-water separator

    International Nuclear Information System (INIS)

    Modrak, T.M.; Curtis, R.W.

    1978-01-01

    The steam-water separator connected downstream of a steam generator consists of a vertical centrifugal separator with swirl blades between two concentric pipes and a cyclone separator located above. The water separated in the cyclone separator is collected in the inner tube of the centrifugal separator which is closed at the bottom. This design allows the overall height of the separator to be reduced. (DG) [de

  17. Interactions between renewable energy policy and renewable energy industrial policy: A critical analysis of China's policy approach to renewable energies

    International Nuclear Information System (INIS)

    Zhang, Sufang; Andrews-Speed, Philip; Zhao, Xiaoli; He, Yongxiu

    2013-01-01

    This paper analyzes China's policy approach to renewable energies and assesses how effectively China has met the ideal of appropriate interactions between renewable energy policy and renewable energy industrial policy. First we briefly discuss the interactions between these two policies. Then we outline China's key renewable energy and renewable industrial policies and find that China's government has well recognized the need for this policy interaction. After that, we study the achievements and problems in China's wind and solar PV sector during 2005–2012 and argue that China's policy approach to renewable energies has placed priority first on developing a renewable energy manufacturing industry and only second on renewable energy itself, and it has not effectively met the ideal of appropriate interactions between renewable energy policy and renewable energy industrial policy. Lastly, we make an in-depth analysis of the three ideas underlying this policy approach, that is, the green development idea, the low-carbon leadership idea and indigenous innovation idea. We conclude that Chinas' policy approach to renewable energies needs to enhance the interactions between renewable energy policy and renewable energy industrial policy. The paper contributes to a deeper understanding of China's policy strategy toward renewable energies. -- Highlights: •Interactions between renewable energy policy and renewable energy industrial policy are discussed. •China's key renewable energy and renewable energy industrial policies are outlined. •Two empirical cases illustrate China's policy approach to renewable energies. •We argue that China needs to enhance the interactions between the two policies. •Three ideas underlie China's policy approach to renewable energies

  18. 48 CFR 570.401 - Renewal options.

    Science.gov (United States)

    2010-10-01

    ... 48 Federal Acquisition Regulations System 4 2010-10-01 2010-10-01 false Renewal options. 570.401... Requirements 570.401 Renewal options. (a) Exercise of options. Before exercising an option to renew, follow the... survey. Before exercising an option to renew a lease, review current market information to ensure the...

  19. 2012 Renewable Energy Data Book (Book)

    Energy Technology Data Exchange (ETDEWEB)

    Gelman, R.

    2013-10-01

    This Renewable Energy Data Book for 2012 provides facts and figures in a graphical format on energy in general, renewable electricity in the United States, global renewable energy development, wind power, solar power, geothermal power, biopower, hydropower, advanced water power, hydrogen, renewable fuels, and clean energy investment.

  20. 2011 Renewable Energy Data Book (Book)

    Energy Technology Data Exchange (ETDEWEB)

    Gelman, R.

    2012-10-01

    This Renewable Energy Data Book for 2011 provides facts and figures on energy in general, renewable electricity in the United States, global renewable energy development, wind power, solar energy, geothermal power, biopower, hydropower, advanced water power, hydrogen, renewable fuels, and clean energy investments.

  1. 2010 Renewable Energy Data Book (Book)

    Energy Technology Data Exchange (ETDEWEB)

    Gelman, R.

    2011-10-01

    This Renewable Energy Data Book for 2010 provides facts and figures on energy in general, renewable electricity in the United States, global renewable energy development, wind power, solar energy, geothermal power, biopower, hydropower, advanced water power, hydrogen, renewable fuels, and clean energy investments.

  2. 2013 Renewable Energy Data Book (Book)

    Energy Technology Data Exchange (ETDEWEB)

    Esterly, S.

    2014-12-01

    This Renewable Energy Data Book for 2013 provides facts and figures on energy in general, renewable electricity in the United States, global renewable energy development, wind power, solar power, geothermal power, biopower, hydropower, advanced water power, hydrogen, renewable fuels, and clean energy investment.

  3. Renewal processes with costs and rewards

    NARCIS (Netherlands)

    Vlasiou, M.; Cochran, J.J.; Cox, L.A.; Keskinocak, P.; Kharoufeh, J.P.; Smith, J.C.

    2011-01-01

    We review the theory of renewal reward processes, which describes renewal processes that have some cost or reward associated with each cycle. We present a new simplified proof of the renewal reward theorem that mimics the proof of the Elementary Renewal Theorem and avoids the technicalities in the

  4. Separation of BSA through FAU-type zeolite ceramic composite membrane formed on tubular ceramic support: Optimization of process parameters by hybrid response surface methodology and biobjective genetic algorithm.

    Science.gov (United States)

    Vinoth Kumar, R; Ganesh Moorthy, I; Pugazhenthi, G

    2017-08-09

    In this study, Faujasite (FAU) zeolite was coated on low-cost tubular ceramic support as a separating layer through hydrothermal route. The mixture of silicate and aluminate solutions was used to create a zeolitic separation layer on the support. The prepared zeolite ceramic composite membrane was characterized using X-ray powder diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), particle size distribution (PSD), field emission scanning electron microscopy (FESEM), and zeta potential measurements. The porosity of ceramic support (53%) was reduced by the deposition of FAU (43%) zeolite layer. The pore size and water permeability of the membrane were evaluated as 0.179 µm and 1.62 × 10 -7  m 3 /m 2  s kPa, respectively, which are lower than that of the support (pore size of 0.309 µm and water permeability of 5.93 × 10 -7  m 3 /m 2  s kPa). The permeate flux and rejection potential of the prepared membrane were evaluated by microfiltration of bovine serum albumin (BSA). To study the influences of three independent variables such as operating pressure (68.94-275.79 kPa), concentration of BSA (100-500 ppm), and solution pH (2-4) on permeate flux and percentage of rejection, the response surface methodology (RSM) was used. The predicted models for permeate flux and rejection were further subjected to biobjective genetic algorithm (GA). The hybrid RSM-GA approach resulted in a maximum permeate flux of 2.66 × 10 -5  m 3 /m 2  s and BSA rejection of 88.02%, at which the optimum conditions were attained as 100 ppm BSA concentration, 2 pH solution, and 275.79 kPa applied pressure. In addition, the separation efficiency was compared with other membranes applied for BSA separation to know the potential of the fabricated FAU zeolite ceramic composite membrane.

  5. Fictional Separation Logic

    DEFF Research Database (Denmark)

    Jensen, Jonas Buhrkal; Birkedal, Lars

    2012-01-01

    , separation means physical separation. In this paper, we introduce \\emph{fictional separation logic}, which includes more general forms of fictional separating conjunctions P * Q, where "*" does not require physical separation, but may also be used in situations where the memory resources described by P and Q...

  6. Proceedings of World Renewable Energy Congress '99

    International Nuclear Information System (INIS)

    Kamaruzzaman Sopian; Mohd Yusof Othman; Baharuddin Yatim

    2000-01-01

    The congress discussed the following subjects, 1. The role of renewable energy in the next millenium; 2. Challenges in the commercialization of renewable energy; 3. The role and agenda for renewable energy towards sustainable development. Topics covered in the technical session were biomass conversion; solar thermal technologies and systems; solar photovoltaic s; renewable energy economics, financing and policy; renewable energy education; climate and the environment; energy and architecture; energy management; wind and hydro technologies and systems; hydrogen and fuel cell

  7. Renewable Energy Policy Fact sheet - Romania

    International Nuclear Information System (INIS)

    2017-07-01

    The EurObserv'ER policy profiles give a snapshot of the renewable energy policy in the EU Member States. The promotion of renewable electricity in Romania relies primarily on a renewable quota scheme. Since 2017 the scheme has been closed for new projects. Renewable heating and cooling is promoted through investment subsidies. Renewable energy sources in the transport sector are promoted by a bio-fuels quota scheme and indirectly through a subsidy scheme for the purchase of electric vehicles

  8. FINANCING RENEWABLE ENERGY SOURCES INVESTMENT IN POLAND

    Directory of Open Access Journals (Sweden)

    Jerzy Piotr Gwizdała

    2017-09-01

    Full Text Available In Poland, as in other European Union countries, the project finance structure is used to finance investments in the field of energy. This method investment financing is often used in the world. The upward trend inhibition in recent periods has been due to the global financial crisis and financial instability in the euro zone. On account of the necessity to develop the energy infrastructure associated with renewable sources, the considerable strengthening in the use of project finance techniques can be expected. The particular progression may be observed in the case of public-private partnership (ppp, where public investments are carried out by private companies. Companies, in case of investment realization in the field of ppp, almost always use project finance, because it is a beneficial way to separate the risks associated with an investment from the balance sheet of the compa-ny.

  9. Renewable energy policy and landscape management in Andalusia, Spain: The facts

    International Nuclear Information System (INIS)

    Prados, Maria-Jose

    2010-01-01

    Renewable energy has developed spectacularly in Spain since the European Union started a process of energy policy reform. A review of Spanish State legislation on renewable energies confirms that the success in installing renewable energy is attributable to public aid. Andalusia is one of the autonomous communities, which has simultaneously developed the legal framework and very successfully implemented the introduction of renewable power. When implementing the central government's policy, the Andalusian regional government prioritised increases in both surface cover by wind and solar plants (thermal and photovoltaic energy) and in the number of companies involved. However, this development of renewable energies took place without any proper integration into regional spatial and landscape planning. This paper explores renewable power implementation in Andalusia through regulatory measures put in place over the last decade to develop renewable energy systems and the way they can be managed alongside planning issues. The location of large-scale renewable plants has had consequences for territory in the socio-political context of renewable energy promotion. The main findings focus on renewable energy plant sprawl throughout rural areas in Andalusia with no clear effect on landscape management and no firm backing from the local population.

  10. Renewal and Change (Editorial

    Directory of Open Access Journals (Sweden)

    Denise Koufogiannakis

    2011-01-01

    Full Text Available The end of yet another calendar year leads to a time of new beginnings and new challenges. For me, this is the end of my three year term as Editor-in-Chief of EBLIP, which has been a very rewarding challenge personally and professionally. I would like to thank each and every person who has contributed to the success of the journal. EBLIP relies on the talented and professional people who regularly give of their time and expertise. I particularly want to thank the Editorial Team who has worked so closely with me over the past three years: Alison Brettle, Lorie Kloda, Katrine Mallan, Jonathan Eldredge, Michelle Dunaway, and our former intern Andrea Baer. Thank you!In the past three years, EBLIP has continued to grow and thrive. We currently have more than 3400 registered readers, and an Editorial Advisory Board comprised of 70 people from 11 countries. Several of our papers have had more than 5000 pdf downloads, and the average number of downloads is 1308. I am also pleased to let you know that we have recently been accepted for inclusion in Scopus.In looking back and reflecting on the past three years, we have continued to build a strong open access journal that is relevant to LIS practitioners. We have increased the number of articles being published, and the overall number of submissions. Content is wide ranging, including multiple sectors within library and information studies. Our evidence summaries continue to be the heart of our journal, with more and more research from our field being critically appraised in this way. We have also added new sections such as Using Evidence in Practice, in which authors reflect on incorporating evidence into practice.And now it is time yet again for renewal and change. I am very pleased to welcome Alison Brettle of the University of Salford, as she begins her three year term as Editor-in-Chief. Alison has been the Associate Editor (Articles since the very early days of publication and brings extensive

  11. MENA Renewables Status Report 2013

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2013-06-15

    The MENA Renewables Status Report is an outcome of ADIREC, the Abu Dhabi International Renewable Energy Conference. The report provides a status overview of renewable energy markets, industry, policy and investment trends in the region, drawing on the most recent data available. It is produced in cooperation with over 50 contributors and researchers in the region and reveals massive growth in the renewable energy markets of the Middle East and North Africa (MENA). Regional investment topped US$2.9 billion in 2012, up 40% from 2011 and 650% from 2004. With over 100 projects under development, the region could see a 450% increase in non-hydro renewable energy generating capacity in the next few years. For the report, the 21 MENA countries were clustered into two sub-groups: Net Oil-Exporting Countries (NOEC) -- Algeria, Bahrain, Egypt, Iran, Iraq, Kuwait, Libya, Oman, Qatar, Saudi Arabia, Syria, United Arab Emirates, and Yemen; and Net Oil-Importing Countries (NOIC) -- Djibouti, Israel, Jordan, Lebanon, Malta, Morocco, Palestine, and Tunisia.

  12. Separation Anxiety (For Parents)

    Science.gov (United States)

    ... Safe Videos for Educators Search English Español Separation Anxiety KidsHealth / For Parents / Separation Anxiety What's in this ... both of you get through it. About Separation Anxiety Babies adapt pretty well to other caregivers. Parents ...

  13. Physical mechanisms in shock-induced turbulent separated flow

    Science.gov (United States)

    Dolling, D. S.

    1987-12-01

    It has been demonstrated that the flow downstream of the moving shock is separated and that the foot of the shock is effectively the instantaneous separation point. The shock induced turbulent separation is an intermittant process and the separation line indicated by surface tracer methods, such as kerosene-lampblack, is a downstream boundary of a region of intermittent separation.

  14. Using Biomolecules to Separate Plutonium

    Science.gov (United States)

    Gogolski, Jarrod

    Used nuclear fuel has traditionally been treated through chemical separations of the radionuclides for recycle or disposal. This research considers a biological approach to such separations based on a series of complex and interdependent interactions that occur naturally in the human body with plutonium. These biological interactions are mediated by the proteins serum transferrin and the transferrin receptor. Transferrin to plutonium in vivo and can deposit plutonium into cells after interacting with the transferrin receptor protein at the cell surface. Using cerium as a non-radioactive surrogate for plutonium, it was found that cerium(IV) required multiple synergistic anions to bind in the N-lobe of the bilobal transferrin protein, creating a conformation of the cerium-loaded protein that would be unable to interact with the transferrin receptor protein to achieve a separation. The behavior of cerium binding to transferrin has contributed to understanding how plutonium(IV)-transferrin interacts in vivo and in biological separations.

  15. Printed Spacecraft Separation System

    Energy Technology Data Exchange (ETDEWEB)

    Dehoff, Ryan R [ORNL; Holmans, Walter [Planetary Systems Corporation

    2016-10-01

    In this project Planetary Systems Corporation proposed utilizing additive manufacturing (3D printing) to manufacture a titanium spacecraft separation system for commercial and US government customers to realize a 90% reduction in the cost and energy. These savings were demonstrated via “printing-in” many of the parts and sub-assemblies into one part, thus greatly reducing the labor associated with design, procurement, assembly and calibration of mechanisms. Planetary Systems Corporation redesigned several of the components of the separation system based on additive manufacturing principles including geometric flexibility and the ability to fabricate complex designs, ability to combine multiple parts of an assembly into a single component, and the ability to optimize design for specific mechanical property targets. Shock absorption was specifically targeted and requirements were established to attenuate damage to the Lightband system from shock of initiation. Planetary Systems Corporation redesigned components based on these requirements and sent the designs to Oak Ridge National Laboratory to be printed. ORNL printed the parts using the Arcam electron beam melting technology based on the desire for the parts to be fabricated from Ti-6Al-4V based on the weight and mechanical performance of the material. A second set of components was fabricated from stainless steel material on the Renishaw laser powder bed technology due to the improved geometric accuracy, surface finish, and wear resistance of the material. Planetary Systems Corporation evaluated these components and determined that 3D printing is potentially a viable method for achieving significant cost and savings metrics.

  16. Apparatus for diffusion separation

    International Nuclear Information System (INIS)

    Nierenberg, W.A.

    1976-01-01

    A diffuser separator apparatus is described which comprises a plurality of flow channels in a single stage. Each of said channels has an inlet port and an outlet port and a constant cross sectional area between said ports. At least a portion of the defining surface of each of said channels is a diffusion separation membrane, and each of said channels is a different cross sectional area. Means are provided for connecting said channels in series so that each successive channel of said series has a smaller cross sectional area than the previous channel of said series. Also provided are a source of gaseous mixture, individual means for flowing said gaseous mixture to the inlet port of each of said channels, gas receiving and analyzing means, individual means for flowing gas passing from each of said outlet ports and means for flowing gas passing through said membranes to said receiving and analyzing means, and individual means for connecting the outlet port of each channel with the inlet port of the channel having the next smaller cross sectional area

  17. Introduction to Renewable Energy Systems

    DEFF Research Database (Denmark)

    Ma, Ke; Yang, Yongheng; Blaabjerg, Frede

    2014-01-01

    . It is concluded that as the quick development of renewable energy, wind power and PV power both show great potential to be largely integrated into the power grid. Power electronics is playing essential role in both of the systems to achieve more controllable, efficient, and reliable energy production......In this chapter, the state-of-the-arts developments of renewable energy are reviewed in respect to the installed power and market share, where wind power and photovoltaic power generation are the main focuses due to the fast growing speed and large share of installed capacity. Some basic principles...... of operation, mission profiles, as well as power electronics solutions and corresponding controls are discussed respectively in the case of wind power and photovoltaic power systems. Finally a few development trends for renewable energy conversions are also given from a power electronics point of view...

  18. Renewable Energy CSOPs in Germany

    Directory of Open Access Journals (Sweden)

    Jens Lowitzsch

    2013-01-01

    Full Text Available The Energy-CSOP facilitates broad equity participation of citizens without assets or savings in a regulated public energy utility. As the CSOP is designed for regulated markets with guaranteed prices, regulated market access and long-term relationships between producer and consumer, the energy market is predestined. A CSOP trust can be set up for a renewable energy plant (e.g., a biogas reactor, a solar panel, a windmill or a geothermic drill. European states have set an ambitious target to reach 20% share of energy from renewable sources by 2020. Germany as Europe’s green energy leader could become a pioneer in CSOP implementation. Small communities in Europe would benefit from the increased share of renewable energy resources.

  19. Renewable Energy Devices and Systems

    DEFF Research Database (Denmark)

    Blaabjerg, Frede; Ionel, Dan M.

    2015-01-01

    In this paper, essential statistics demonstrating the increasing role of renewable energy generation are firstly discussed. A state of the art review section covers fundamentals of wind turbines and PV systems. Included are schematic diagrams illustrating the main components and system topologies...... and the fundamental and increasing role of power electronics as an enabler for renewable energy integration, and for the future power system and smart grid. Recent examples of research and development, including new devices and system installations for utility power plants, as well for as residential and commercial......, fuel cells, and storage with batteries and hydrogen, respectively. Recommended further readings on topics of electric power engineering for renewable energy are included in a final section. This paper also represents an editorial introduction for two special issues of the Electric Power Component...

  20. Renewable energy market overview 2000

    International Nuclear Information System (INIS)

    Mahoney, Nicholas

    2001-01-01

    The article discusses the findings of a recent survey on the renewable energy market carried out in 164 countries and across a wide range of sectors of industry. The survey found almost unanimous optimism regarding the growth of the renewable energy market over the coming year. Tables show (i) the survey sample (in terms of continents, database population and responses); (ii) subsidiaries and locations of parent companies; (iii) expectations of sales next year (by continent) and (iv) expectations of sales in the coming year by sector. Figures show (a) regional distribution of companies (by continent); (b) companies' activities and (c) index of expectations of sales, by continent. The survey is intended for inclusion in the World Directory of Renewable Energy Suppliers and Services

  1. Project financing renewable energy schemes

    International Nuclear Information System (INIS)

    Brandler, A.

    1993-01-01

    The viability of many Renewable Energy projects is critically dependent upon the ability of these projects to secure the necessary financing on acceptable terms. The principal objective of the study was to provide an overview to project developers of project financing techniques and the conditions under which project finance for Renewable Energy schemes could be raised, focussing on the potential sources of finance, the typical project financing structures that could be utilised for Renewable Energy schemes and the risk/return and security requirements of lenders, investors and other potential sources of financing. A second objective is to describe the appropriate strategy and tactics for developers to adopt in approaching the financing markets for such projects. (author)

  2. Renewable energy market overview 2000

    Energy Technology Data Exchange (ETDEWEB)

    Mahoney, Nicholas

    2001-02-01

    The article discusses the findings of a recent survey on the renewable energy market carried out in 164 countries and across a wide range of sectors of industry. The survey found almost unanimous optimism regarding the growth of the renewable energy market over the coming year. Tables show (i) the survey sample (in terms of continents, database population and responses); (ii) subsidiaries and locations of parent companies; (iii) expectations of sales next year (by continent) and (iv) expectations of sales in the coming year by sector. Figures show (a) regional distribution of companies (by continent); (b) companies' activities and (c) index of expectations of sales, by continent. The survey is intended for inclusion in the World Directory of Renewable Energy Suppliers and Services.

  3. Renewable energies. Italy is mobilizing

    International Nuclear Information System (INIS)

    Marante, W.

    2005-01-01

    About 3 quarter of the Italian electric power comes from fossil fuel power plants. The rest is generated from hydropower, few comes from biomass and wind energy and a very few from geothermal energy (2% of the national production). However, the situation is changing and geothermal energy, with only 5 TWh, makes Italy the European leader in this domain and the world number 4 behind USA, Philippines and Mexico. The renewable sources represent 18.5% of the total Italian energy production. During the last five years, the renewable energy sources have developed rapidly: +80% per year for the wind energy, +32% per year for biomass and about +3% per year for geothermal energy. Moreover, the Italian government is implementing incentives for the development of renewable energy sources. This article gives an overview of the situation. (J.S.)

  4. China's renewable energy policy: Commitments and challenges

    International Nuclear Information System (INIS)

    Wang Feng; Yin Haitao; Li Shoude

    2010-01-01

    The passing of the Renewable Energy Law (REL) in 2005 demonstrated China's commitment to renewable energy development. In the 3 years after the REL, China's renewable electricity capacity grew rapidly. From 2006 to 2008, China's wind capacity installation more than doubled every year for 3 years in a row. However, three facts prevent us from being optimistic about China's renewable electricity future. First, considered as a share of total capacity, renewable electricity capacity is decreasing instead of increasing. This is due simply to the rapid growth of fossil fuel capacity. Second, a significant amount of renewable generation capacity is wasted because it is not connected to the electricity grid. Finally, renewable electricity plants are running at a low level of efficiency. Based on an in-depth analysis of China's existing renewable energy policy, we suggest that these challenges should be dealt with by introducing a market-based mandatory renewable portfolio requirement coupled with strong regulatory monitoring of grid enterprises.

  5. Renewable energy technology acceptance in Peninsular Malaysia

    International Nuclear Information System (INIS)

    Kardooni, Roozbeh; Yusoff, Sumiani Binti; Kari, Fatimah Binti

    2016-01-01

    Despite various policies, renewable energy resources have not been developed in Malaysia. This study investigates the factors that influence renewable energy technology acceptance in Peninsular Malaysia and attempts to show the impact of cost and knowledge on the perceived ease of use and perceived usefulness of renewable energy technology. The results show that cost of renewable energy has an indirect effect on attitudes towards using renewable energy through the associated impact on the perceived ease of use and perceived usefulness. The results also indicate that public knowledge in Peninsular Malaysia does not affect perceived ease of use, although the positive impact of knowledge on perceived usefulness is supported. Furthermore, our results show that the current business environment in Peninsular Malaysia does not support the adoption of renewable energy technology, and thus, renewable energy technology is not commercially viable in Peninsular Malaysia. Additionally, the population of Peninsular Malaysia associates the use of renewable energy with a high level of effort and therefore has a negative attitude towards the use of renewable energy technology. There is, therefore, a definite need to pay more attention to the role of public perception and awareness in the successes and failures of renewable energy policy. - Highlights: • Public acceptance is an essential element in the diffusion of renewable energy. • Perceived ease of use and perceived usefulness affect intention to use renewables. • It is important to reduce the cost of renewable energy, particularly for end users. • Renewable energy policies should address issues of public perception and awareness.

  6. World potential of renewable energies

    Energy Technology Data Exchange (ETDEWEB)

    Dessus, B; Devin, B; Pharabod, F

    1991-07-01

    A comprehensive analysis, region by region, of the actually accessible renewable energies at a given horizon, is presented. The same methodology as the one employed to derive ``proven fossil energy reserves`` from ``energy resources`` is adopted, in which resources are defined by quantitative information on physical potential, while reserves take into account technical and economical accessibility. As renewable resources are fluctuating with time and are diluted in space and not readily transportable or storeable, it is necessary to consider the presence of populations or activities near enough to be able to profit by these diluted and volatile energies.

  7. Renewables 2012. Global Status Report

    Energy Technology Data Exchange (ETDEWEB)

    Sawin, J. L. [and others

    2012-08-15

    Renewable energy markets and policy frameworks have evolved rapidly in recent years. This report provides a comprehensive and timely overview of renewable energy market, industry, investment, and policy developments worldwide. It relies on the most recent data available, provided by a network of more than 400 contributors and researchers from around the world, all of which is brought together by a multi-disciplinary authoring team. The report covers recent developments, current status, and key trends; by design, it does not provide analysis or forecast the future.

  8. Renewable energy prospects for implementation

    CERN Document Server

    Jackson, Tim

    1993-01-01

    Renewable Energy: Prospects for Implementation contains papers that were originally commissioned by the journal Energy Policy for a series on renewable energy appearing between January 1991 to September 1992. In view of the fast-changing demands on conventional energy supply to meet environmental imperatives, it seemed timely to reproduce here a selection of those papers with a new introduction and a revised concluding chapter by the Editor of the series, Dr Tim Jackson, a research fellow with the Stockholm Environment Institute. The book is organized into four parts. The papers in Part I

  9. Renewable energy sources. Erneuerbare Energien

    Energy Technology Data Exchange (ETDEWEB)

    1988-01-01

    To judge future trends in work on the exploitation of renewable energy sources for overall energy supply, it is necessary to know the following: the rules that nature abides by, the principles of technical exploitation of these energies, and the basic data for the current state of development. The above information is compiled in this publication for those renewable energy sources on which topical discussion centres: solar radiation and wind. For the remaining renowable energy sources (e.g. biomass, tidal power, geothermal energy), some examples of use are mentioned and advanced literature is indicated. (orig./HSCH).

  10. Renewable energies: the Spanish assets

    International Nuclear Information System (INIS)

    Petit-Pez, Ch.; Molenat, G.

    2009-01-01

    Even though Spain is far away from the Kyoto protocol objectives, this country possesses numerous assets in terms of renewable energies. This report presents overviews of the present situation and of innovation and research activities in the different fields of renewable energies: wind energy, solar energy (thermal, thermoelectric and photovoltaic), hydraulic energy (dams, tide and wave energy), biomass (wood, bio-fuels, biogas). Along with these presentations, the authors propose tables and graphs of quantitative data concerning these different energy productions, at the national as well as at the regional level, with comparison with data for other European countries

  11. Renewable energies - Situation and perspectives

    International Nuclear Information System (INIS)

    Acket, Claude; Vaillant, Jacques

    2011-01-01

    The world has to face increasing energy needs while it is today dependent of fossil fuels at 80%. Getting out of the fossil fuels dependence model requires an important effort to promote the energy saving and the carbon-free energies as well, and in particular the renewable energy sources. Taking all this information into account, the authors evaluate the global share that renewable energies could represent in the energy mix, in France and in the entire world. This share represents today only 10% of the energy consumed, but will it remain marginal or will it become important and eventually prominent? (J.S.)

  12. Comment: The Economics of Interdependent Renewable and Non-renewable Resources revisited.

    OpenAIRE

    Viktoria Kahui; Claire W. Armstrong

    2009-01-01

    This work expands upon Swallow's theoretical analysis of interactions between renewable and non-renewable resources. In this comment the interaction is such that the renewable resource prefers the non-renewable environment, as opposed to SwallowÕs (op cit) case of the non-renewable environment being essential to the renewable resource. We find that this difference strongly affects the results, and makes the resources change from being complements to being substitutes, i.e. in the essential ca...

  13. Equilibrium Transitions from Non Renewable Energy to Renewable Energy under Capacity Constraints

    OpenAIRE

    Amigues, Jean-Pierre; Ayong Le Kama, Alain; Moreaux, Michel

    2013-01-01

    We study the transition between non-renewable and renewable energy sources with adjustment costs over the production capacity of renewable energy. Assuming constant variable marginal costs for both energy sources, convex adjustment costs and a more expensive renewable energy, we show the following. With sufficiently abundant non-renewable energy endowments, the dynamic equilibrium path is composed of a first time phase of only non-renewable energy use followed by a transition phase substituti...

  14. The renewable energy field is gaining power

    Energy Technology Data Exchange (ETDEWEB)

    Fuller, D.B.

    1984-01-01

    For about 25 years, Basic Resources Corp. in New York has been growing on the strength of operations ranging from oil and gas exploration and printing to computer leasing and the manufacture of highway toll-collecting equipment. But since early 1982, when it received an Energy Department grant, a new subsidiary has been working on a project with scant resemblance to any other of the multimillion-dollar firm's operations: the preliminary research for an ocean thermal energy plant that would convert heat on the ocean's surface to power at a site in the Hawaiian islands. Renewable energy -- once largely the domain of dreamers and urban dropouts -- has moved into the corporate mainstream, and more and more companies in the United States and abroad are trying to stake a claim to a piece of its future. Basic Resources is not the only renewable energy source firm doing well. Several hundred exhibitors and other participants -- including a number of foreign visitors -- turned out for the 3-day event. Arco, which has been working on photovoltaics since the late 1970s, is considered the world's largest manufacturer of photovoltaics -- solar cells that convert the sun's energy directly into electricity. But, despite tax credits, worldwide sales and dramatic strides in reducing the cost of the technology, the operation still isn't profitable after the costs of research and other costreduction efforts are included. Nonetheless, Arco has no plans to abandon the field, and its attitude explains why so many firms are bucking the odds and pursuing renewable energy.

  15. New separation technique. Catalytically functionated separation membrane

    Energy Technology Data Exchange (ETDEWEB)

    Urgami, Tadashi [Kansai Univ., Osaka (Japan)

    1989-02-01

    This report introduces research examples, showing the fundamental principle of the membrane by separating the catalytically functionated separation membrane into enzyme fixing separation membrane, polymerized metal complex separation membrane and polymer catalyst separation membrane. This membrane can achieve both functions of separation and catalytic reaction simultaneously and has sufficient possibility to combine powerful functions. Enzyme fixing separation membrane is prepared by carrier combination method, bridging method or covering method and the enzyme fixing method with polymerized complex in which enzyme is controlled to prevent the activity lowering as much as possible and enzyme is fixed from an aqueous solution into polymer membrane. This membrane is applied to the continuous manufacturing of invert sugar from cane sugar and adsorption and removing of harmful substances from blood by utilizing both micro-capsuled urease and active carbon. Alginic acid-copper (II) complex membrane is used for the polymerized metal complex membrane and polystyrene sulfonate membrane is used for the polymer catalyst separation membrane. 28 refs., 4 figs., 1 tabs.

  16. Basic concepts for designing renewable electricity support aiming at a full-scale transition by 2050

    International Nuclear Information System (INIS)

    Verbruggen, Aviel; Lauber, Volkmar

    2009-01-01

    Renewable electricity supply is a crucial factor in the realization of a low-carbon energy economy. The understanding is growing that a full turn-over of the electricity sectors by 2050 is an elementary condition for avoiding global average temperature increase beyond 2 C. This article adopts such full transition as Europe's target when designing renewable energy policy. An immediate corollary is that phasing-in unprecedented energy efficiency and renewable generation must be paralleled by phasing-out non-sustainable fossil fuel and nuclear power technologies. The double phasing programme assigns novel meaning to nearby target settings for renewable power as share of total power consumption. It requires organizing in the medium term EU-wide markets for green power, a highly demanding task in the present context of poorly functional markets in brown power. The EU Commission's 2007/2008 proposals of expanding tradable certificates markets were not based on solid analysis of past experiences and future necessities. The keystone of sound policies on renewable electricity development is a detailed scientific differentiation and qualification of renewable electricity sources and technologies, for measuring the huge diversity in the field. We provide but structuring concepts about such qualification, because implementation requires extensive research resources. Support for renewable electricity development is organized via feed-in prices or premiums, and via quota obligations connected to tradable green certificates. Green certificates are dependent on physical generated renewable power, but separable and no joint products. Contrary to conventional wisdom we argue their separation in cost analysis but firm linking during trade. A few graphs illustrate the importance of assigning qualities to different renewable power sources/technologies. Feed-in systems based on an acceptable qualification perform generally better than certificate markets imposing uniform approaches on a

  17. Alaska's renewable energy potential.

    Energy Technology Data Exchange (ETDEWEB)

    2009-02-01

    This paper delivers a brief survey of renewable energy technologies applicable to Alaska's climate, latitude, geography, and geology. We first identify Alaska's natural renewable energy resources and which renewable energy technologies would be most productive. e survey the current state of renewable energy technologies and research efforts within the U.S. and, where appropriate, internationally. We also present information on the current state of Alaska's renewable energy assets, incentives, and commercial enterprises. Finally, we escribe places where research efforts at Sandia National Laboratories could assist the state of Alaska with its renewable energy technology investment efforts.

  18. Renewable energy policy. Into the mainstream

    International Nuclear Information System (INIS)

    2003-01-01

    Renewable energy today is at a critical stage of development: renewable technologies are maturing, and costs for some technologies are in the competitive range. Beyond the energy they produce, renewable energy technologies offer a variety of other benefits towards the achievement of sustainable development goals. This promise has led to all IEA governments to support their greater development. But, while renewables markets are growing strongly, additional steps must be taken to accelerate the achievement of sustainable, large-scale markets. This report by the IEA's Renewable Energy Working Party outlines those steps, and the benefits of moving renewable energy into the mainstream

  19. Controlling Separation in Turbomachines

    Science.gov (United States)

    Evans, Simon; Himmel, Christoph; Power, Bronwyn; Wakelam, Christian; Xu, Liping; Hynes, Tom; Hodson, Howard

    2010-01-01

    Four examples of flow control: 1) Passive control of LP turbine blades (Laminar separation control). 2) Aspiration of a conventional axial compressor blade (Turbulent separation control). 3) Compressor blade designed for aspiration (Turbulent separation control). 4.Control of intakes in crosswinds (Turbulent separation control).

  20. Renewable Energy Country Profiles. Caribbean

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2012-09-15

    IRENA Renewable Energy Country Profiles take stock of the latest developments in the field of renewables at country level around the world. Each profile combines analysis by IRENA's specialists with the latest available country data and additional information from a wide array of sources. The resulting reports provide a brief yet comprehensive picture of the situation with regard to renewable energy, including energy supply, electrical generation and grid capacity, and access. Energy policies, targets and projects are also considered, along with each country's investment climate and endowment with renewable energy resources. The energy statistics presented here span the period from 2009 until 2012, reflecting varying timelines in the source material. Since data availability differs from country to country, wider regional comparisons are possible only for the latest year with figures available for every country included. Despite the time lag in some cases, the evident differences and disparities between countries and regions around the world remain striking. The current package of country profiles is just a starting point. The geographic scope will continue to expand, and existing profiles will be enhanced with new indicators, with the whole series maintained as a live product on the IRENA website (www.irena.org)

  1. The USNCR license renewal process

    International Nuclear Information System (INIS)

    Kuo, Pao-Tsin

    2002-01-01

    The US Congress promulgated a law in 1954, entitled 'Atomic Energy Act'. This Act states that operating licenses for commercial nuclear power plants are limited to a fixed term of 40 years, but they may be renewed for a period not to exceed 20 years. The terms were established mainly for economic considerations, not based on technical limitations. The U.S. Nuclear Regulatory Commission (USNRC) published the license renewal rule, Title 10 of the Code of Federal Regulations, Part 54 (10 CFR Part 54), in December, 1991. The rule has since been amended in May, 1995. The underlying principle of the rule is that the regulatory process is adequate for ensuring safety of operating plants. The regulatory process includes NRC's issuance of Orders, Bulletins, Generic Letters, and Information Notices, as well as a number of special inspections in addition to the continuous oversight and routine inspection activities performed by on-site inspectors. Because of this comprehensive regulatory process, compilation of the current license basis or re-verification of the current licensing basis is not considered necessary for a license renewal review. The USNRC also determined on the basis of the findings of its research programs that active structures and components are well maintained by the existing programs. Therefore, the focus of the license renewal review is on passive, long-lived structures and components and on time-limited ageing analyses. The time-limited ageing analyses are for those structures and components which were originally designed to a 40 year service life

  2. The potential of renewable energy

    Energy Technology Data Exchange (ETDEWEB)

    1990-03-01

    On June 27 and 28, 1989, the US Department of Energy (DOE) national laboratories were convened to discuss plans for the development of a National Energy Strategy (NES) and, in particular, the analytic needs in support of NES that could be addressed by the laboratories. As a result of that meeting, interlaboratory teams were formed to produce analytic white papers on key topics, and a lead laboratory was designated for each core laboratory team. The broad-ranging renewables assignment is summarized by the following issue statement from the Office of Policy, Planning and Analysis: to what extent can renewable energy technologies contribute to diversifying sources of energy supply What are the major barriers to greater renewable energy use and what is the potential timing of widespread commercialization for various categories of applications This report presents the results of the intensive activity initiated by the June 1989 meeting to produce a white paper on renewable energy. Scores of scientists, analysts, and engineers in the five core laboratories gave generously of their time over the past eight months to produce this document. Their generous, constructive efforts are hereby gratefully acknowledged. 126 refs., 44 figs., 32 tabs.

  3. Shapes of a Renewable Society.

    Science.gov (United States)

    Deudney, Daniel; Flavin, Christopher

    1983-01-01

    To rely on coal and nuclear power as sources of energy is to narrow society's future options and to present numerous problems. Renewable solar energy, on the other hand, can preserve rather than reduce options. More jobs, rising self-reliance, and new equalities between nations will be the result. (RM)

  4. Innovative biofibers from renewable resources

    CERN Document Server

    Reddy, Narendra

    2015-01-01

    This book will be a one-stop-shop for readers seeking information on biofibers that are sustainable and environmentally friendly and those that can replace the non-renewable synthetic polymer based fibers. Emphasis will be on fibers that are derived from agricultural byproducts and coproducts without the need for additional natural resources.

  5. Solar Renewable Energy. Teaching Unit.

    Science.gov (United States)

    Buchanan, Marion; And Others

    This unit develops the concept of solar energy as a renewable resource. It includes: (1) an introductory section (developing understandings of photosynthesis and impact of solar energy); (2) information on solar energy use (including applications and geographic limitations of solar energy use); and (3) future considerations of solar energy…

  6. Analysis of renewable portfolio standards

    Energy Technology Data Exchange (ETDEWEB)

    Bernow, S.; Dougherty, W.; Duckworth, M.

    1997-12-31

    A national RPS would increase the fraction of U.S. electricity generation from renewable technologies at least cost. It would help ensure that the cost and performance of these technologies would improve with manufacturing experience, scale economies, and learning-by-doing from their integration into electric systems. Thus, their economic, environmental, energy security, and sustainability benefits would be realized.

  7. Legal framework: Renewables in Honduras

    International Nuclear Information System (INIS)

    Matute, Leonardo

    2000-01-01

    The paper describes the framework (organic structure and legislation) in promotion of renewables in Honduras, the policies for promotion of the free market of energy, laws on environmental protection and law of electricity. Also describes treties and agreements suscribed by Honduras in these matters

  8. Renewables 2012 - Global status report

    International Nuclear Information System (INIS)

    Sawin, Janet L.; Bhattacharya, Sribas Chandra; Galan, Ernesto Macias; McCrone, Angus; Moomaw, William R.; Sims, Ralph; Sonntag-O'Brien, Virginia; Sverrisson, Freyr; Chawla, Kanika; Adib, Rana; Musolino, Evan; Mastny, Lisa; Skeen, Jonathan; Martinot, Eric; Hinrichs-Rahlwes, Rainer

    2012-01-01

    Renewable energy markets and policy frameworks have evolved rapidly in recent years. This report provides a comprehensive and timely overview of renewable energy market, industry, investment, and policy developments worldwide. It relies on the most recent data available, provided by a network of more than 400 contributors and researchers from around the world, all of which is brought together by a multi-disciplinary authoring team. The report covers recent developments, current status, and key trends; by design, it does not provide analysis or forecast the future. As such, this report and subsequent editions will serve as a benchmark for measuring global progress in the deployment of renewable energy, which is of particular interest in this International Year of Sustainable Energy for All. UN Secretary-General Ban Ki-moon has marked the occasion with a new global initiative, Sustainable Energy for All, which seeks to mobilise global action on three inter-linked objectives to be achieved by 2030: universal access to modern energy services, improved rates of energy efficiency, and expanded use of renewable energy sources

  9. Power marketing and renewable energy

    International Nuclear Information System (INIS)

    Fang, J.M.

    1997-01-01

    Power marketing refers to wholesale and retail transactions of electric power made by companies other than public power entities and the regulated utilities that own the generation and distribution lines. The growth in power marketing has been a major development in the electric power industry during the last few years, and power marketers are expected to realize even more market opportunities as electric industry deregulation proceeds from wholesale competition to retail competition. This Topical Issues Brief examines the nature of the power marketing business and its relationship with renewable power. The information presented is based on interviews conducted with nine power marketing companies, which accounted for almost 54% of total power sales by power marketers in 1995. These interviews provided information on various viewpoints of power marketers, their experience with renewables, and their respective outlooks for including renewables in their resource portfolios. Some basic differences exist between wholesale and retail competition that should be recognized when discussing power marketing and renewable power. At the wholesale level, the majority of power marketers stress the commodity nature of electricity. The primary criteria for developing resource portfolios are the same as those of their wholesale customers: the cost and reliability of power supplies. At the retail level, electricity may be viewed as a product that includes value-added characteristics or services determined by customer preferences

  10. Renewable energies and public policies

    International Nuclear Information System (INIS)

    Cochet, Y.; Pierret, Ch.; Lienemann, M.N.

    2002-04-01

    This document presents the interventions of political personalities on the topic of the renewable energies development policies and the necessity of financial incentives which have been discussed during the colloquium of thursday 4 april 2002 at Paris. (A.L.B.)

  11. The renewable energies in Uruguay

    International Nuclear Information System (INIS)

    2011-01-01

    This report is about the energetic politc and its strong commitment with the incorporation of autochthonous sources and renewable energy. The objective and the main lines of action in Uruguay are: provide electric power, wind, biomass, bioethanol, biodiesel, solar and hydroelectric power

  12. Conservation and Renewable Energy Program

    Energy Technology Data Exchange (ETDEWEB)

    Vaughan, K.H.

    1991-05-01

    This bibliography lists reports and selected papers published under the Oak Ridge National Laboratory Conservation and Renewable Energy Program from 1986 through February 1991. Information on documents published prior to 1986 can be obtained from ORNL. Most of the documents in the bibliography are available from Oak Ridge National Laboratory.

  13. Heliodromus : Renewable energy from space

    NARCIS (Netherlands)

    Kuiper, J.M.

    2010-01-01

    Climate change and the related running out of fossil fuel reserves drive the development of renewable energy sources. To contribute to a solution of these problems, we present the results of a BSc student design synthesis exercise project on Space Based Solar Power (SBSP). A SBSP system generates

  14. New Quebec renewable energy organization

    Energy Technology Data Exchange (ETDEWEB)

    McArthur, D.; Salaff, S.

    1998-04-01

    The recent formation of the Quebec Association for the Production of Renewable Energy (l`Association quebecoise de la production d`energie renouvelable - AQPER) was announced. The Association is becoming the centre of the Quebec private electricity generation industry. By communicating the industry`s message to the public the organization gives much needed visibility to renewable resources, new forms of energy and sustainable development. The new group is an outgrowth of the former Quebec Association of Private Hydroelectricity Producers. In its new reincarnation, the organization represents all forms of renewables, small and medium hydro, wind, solar, forest and agricultural biomass and urban waste. With deregulation of the electricity market, specifically the creation of the Regie de l`energie` in Quebec, the wider role is a welcome boost for renewable energy development in the province. In one of its first actions the AQPER recommended that all hydroelectric sites up to 50 MW be reserved for development exclusively by the private sector, in conformity with the Quebec energy policy announced in 1996.

  15. Renewable electricity in the Netherlands

    International Nuclear Information System (INIS)

    Junginger, M.; Agterbosch, S.; Faaij, A.; Turkenburg, W.

    2004-01-01

    The Dutch policy goal is to achieve a share of 17% renewable electricity in the domestic demand in 2020, corresponding to 18-24 TWh. It is uncertain whether and under which conditions this aim can be achieved. This paper aims to explore the feasible deployment of renewable electricity production in the Netherlands until 2020 by evaluating different images representing policies and societal preferences. Simultaneously, the most promising technologies for different settings are investigated and identified. First Dutch policy goals, governmental policy measures and definitions of renewable electricity are discussed. Second, a comparison is made of four existing studies that analyze the possible developments of renewable electricity production in the coming decades. Finally, three images are set up with emphasis on the different key factors that influence the maximum realizable potential. Results indicate onshore wind, offshore wind and large-scale biomass plants as most promising, robust options in terms of economical performance, ecological sustainability and high technical implementation rate. In the image with high implementation rates, an annual production of 42 TWh may be achieved in 2020, while under stringent economical or ecological criteria, about 25 TWh may be reached. When only the robust options are considered, 9-22 TWh can be realized. The analysis illustrates the importance of taking the different key factors mentioned influencing implementation into account. Doing so allows for identification of robust and less robust technological options under different conditions

  16. Use of total internal reflection Raman (TIR) and attenuated total reflection infrared (ATR-IR) spectroscopy to analyze component separation in thin offset ink films after setting on coated paper surfaces.

    Science.gov (United States)

    Kivioja, Antti; Hartus, Timo; Vuorinen, Tapani; Gane, Patrick; Jääskeläinen, Anna-Stiina

    2013-06-01

    The interactive behavior of ink constituents with porous substrates during and after the offset print process has an important effect on the quality of printed products. To help elucidate the distribution of ink components between the retained ink layer and the substrate, a variety of spectroscopic and microscopic analysis techniques have been developed. This paper describes for the first time the use of total internal reflection (TIR) Raman spectroscopy to analyze the penetration behavior of separated offset ink components (linseed oil, solid color pigment) in coated papers providing chemically intrinsic information rapidly, nondestructively, and with minimal sample preparation. In addition, the already widely applied technique of attenuated total reflection infrared spectroscopy (ATR-IR) was evaluated in parallel and compared. The results of the ATR-IR Raman clearly revealed an improvement in uppermost depth resolution compared with values previously published from other nondestructive techniques, and the method is shown to be capable of providing new knowledge of the setting of thin (0.25-2 μm) offset ink films, allowing the spreading and the penetration behavior on physically different paper coating surfaces to be studied.

  17. Christmas Valley Renewable Energy Assessment

    Energy Technology Data Exchange (ETDEWEB)

    Del Mar, Robert [Oregon Department of Energy, Salem, OR (United States)

    2017-05-22

    In partnership with the Oregon Military Department, the Department of Energy used the award to assess and evaluate renewable resources in a 2,622-acre location in Lake County, central Oregon, leading to future development of up to 200 MW of solar electricity. In partnership with the Oregon Military Department, the Department of Energy used the award to assess and evaluate renewable resources in a 2,622-acre location in Lake County, central Oregon, leading to future development of up to 200 MW of solar electricity. The Oregon Military Department (Military) acquired a large parcel of land located in south central Oregon. The land was previously owned by the US Air Force and developed for an Over-the-Horizon Backscatter Radar Transmitter Facility, located about 10 miles east of the town of Christmas Valley. The Military is investigating a number of uses for the site, including Research and Development (R&D) laboratory, emergency response, military operations, developing renewable energy and related educational programs. One of the key potential uses would be for a large scale solar photovoltaic power plant. This is an attractive use because the site has excellent solar exposure; an existing strong electrical interconnection to the power grid; and a secure location at a moderate cost per acre. The project objectives include: 1. Site evaluation 2. Research and Development (R&D) facility analysis 3. Utility interconnection studies and agreements 4. Additional on-site renewable energy resources analysis 5. Community education, outreach and mitigation 6. Renewable energy and emergency readiness training program for veterans

  18. Renewable energy resources; Erneuerbare Energien

    Energy Technology Data Exchange (ETDEWEB)

    Lenz, Volker; Naumann, Karin [DBFZ Deutsches Biomasseforschungszentrum gemeinnuetzige GmbH, Leipzig (Germany); Kaltschmitt, Martin; Janczik, Sebastian [Technische Univ. Hamburg-Harburg (Germany). Inst. fuer Umwelttechnik und Energiewirtschaft

    2015-07-01

    Although the need to decarbonise our global economy and thus in particular the supply of energy to limit the global temperature increase is internationally undisputed the German politics in 2014 has significantly contributed less compared to previous years in order to attain this objective. The expansion of renewable energies in the electricity sector has decelerated significantly; and in the heating and mobility area no new impulses were set in relation to renewable energies. In addition, a dramatic fallen oil price makes it difficult to increase the use of renewable energy supply. Based on these deteriorated framework conditions compared to conditions of the previous years, the developments in Germany of 2014 are shown in the electricity, heat and transport sector in the field of renewable energy. For this purpose - in addition to a discussion of the current energy economic framework - for each option to use renewable energies the state and looming trends are analyzed. [German] Obwohl die Notwendigkeit zur Dekarbonisierung unserer globalen Wirtschaft und damit insbesondere der Energiebereitstellung zur Begrenzung des globalen Temperaturanstiegs international unstrittig ist, hat die deutsche Politik im Jahr 2014 im Vergleich zu den Vorjahren deutlich weniger zur Erreichung dieses Zieles beigetragen. Der Ausbau der Stromerzeugung aus erneuerbaren Energien im Stromsektor wurde deutlich verlangsamt; und im Waerme- und Mobilitaetsbereich wurden keine neuen Impulse in Bezug auf regenerative Energien gesetzt. Zusaetzlich erschwert ein drastisch gefallener Rohoelpreis die verstaerkte Nutzung des erneuerbaren Energieangebots. Ausgehend von diesen im Vergleich zu den Vorjahren verschlechterten Rahmenbedingungen werden nachfolgend die Entwicklungen in Deutschland des Jahres 2014 im Strom-, Waerme- und Transportsektor fuer den Bereich der erneuerbaren Energien aufgezeigt. Dazu werden - neben einer Diskussion des derzeitigen energiewirtschaftlichen Rahmens - fuer die

  19. The Monticello license renewal project

    International Nuclear Information System (INIS)

    Clauss, J.M.; Harrison, D.L.; Pickens, T.A.

    1993-01-01

    Today, 111 nuclear power plants provide over 20 percent of the electrical energy generated in the United States. The operating license of the oldest operating plant will expire in 2003, one-third of the existing operating licenses will expire by 2010 and the newest plant's operating license will expire in 2033. The National Energy Strategy (NES) prepared by the Department of Energy (DOE) assumes that 70 percent of the current operating plants will continue to operate beyond their current license expiration. Power from current operating plants can assist in ensuring an adequate, diverse, and environmentally acceptable energy supply for economic growth and improved U.S. competitiveness. In order to preserve this energy resource, three major tasks must be successfully completed: (1) establishment of regulations, technical standards, and procedures for the preparation and review of License Renewal Applications (LRAs); (2) development of technical criteria and bases for monitoring, refurbishing or replacing plant equipment; and (3) demonstration of the regulatory process by a plant obtaining a renewed license. Since 1986, the DOE has been working with the nuclear industry and the Nuclear Regulatory Commission (NRC) to establish and demonstrate the option to extend the life of a nuclear power plant by renewing the operating license. The Monticello Lead Plant demonstration project was initiated in September 1988, following the Pilot Plant studies. This paper is primarily focused on the status and insights gained from the Northern States Power Company (NSP) Monticello Lead Plant demonstration project. The following information is included: (1) Current Status - Monticello License Renewal Application; (2) Economic Analysis; (3) License Renewal Regulatory Uncertainty Issues; (4) Key Decisions; (5) Management Structure; (6) Technical and Licensing Perspective; (7) NRC Interactions; (8) Summary

  20. Renewables for sustainable village power

    International Nuclear Information System (INIS)

    Flowers, L.

    1997-03-01

    It is estimated that two billion people live without electricity and its services. In addition, there is a sizeable number of rural villages that have limited electrical service, with either part-day operation by diesel gen-sets or partial electrification (local school or community center and several nearby houses). For many villages connected to the grid, power is often sporadically available and of poor quality. The U.S. National Renewable Energy Laboratory (NREL) in Golden, Colorado, has initiated a program to address these potential electricity opportunities in rural villages through the application of renewable energy (RE) technologies. The objective of this program is to develop and implement applications that demonstrate the technical performance, economic competitiveness, operational viability, and environmental benefits of renewable rural electric solutions, compared to the conventional options of line extension and isolated diesel mini-grids. These four attributes foster sustainability; therefore, the program is entitled Renewables for Sustainable Village Power (RSVP). The RSVP program is a multi-technology, multi-application program composed of six activities, including village applications development, computer model development, systems analysis, pilot project development, technical assistance, and Internet-based village power project data base. While the current program emphasizes wind, photovoltaics (PV), and their hybrids with diesel gen-sets, micro-hydro and micro-biomass technologies may be integrated in the future. NREL's RSVP team is currently involved in rural electricity projects in thirteen countries, with U.S., foreign, and internationally based agencies and institutions. The integration of the technology developments, institutional experiences, and the financial solutions for the implementation of renewables in the main line rural electrification processes in both the developing world and remote regions of the developed world is the goal

  1. Implications of renewables on energy planning

    CSIR Research Space (South Africa)

    Bischof-Niemz, T

    2015-10-01

    Full Text Available : Senior consultant (energy system and renewables expert) at The Boston Consulting Group, Berlin and Frankfurt, Germany Education • Master of Public Administration (MPA) on energy and renewables policies in 2009 from Columbia University in New York City...

  2. Strategies and best practices for staff renewal

    International Nuclear Information System (INIS)

    Cottingham, C.

    2007-01-01

    This paper discusses the strategies and best practices for staff renewal in the electricity sector. Strategic initiatives for staff renewal include strategic recruiting, succession planning, employee relations, knowledge management and strategic partnerships

  3. Renewable Energy Park - Preliminary Feasibility & Engineering Report

    Energy Technology Data Exchange (ETDEWEB)

    Ariwite, Roderick [Fallon Paiute Shoshone Tribe, NV (United States)

    2015-07-31

    This "Renewable Energy Park - Preliminary Feasibility & Engineering Report" seeks to provide an overall assessment and review of renewable energy development opportunities on the Fallon Indian Reservation and Colony Lands.

  4. RENEWABLE ENERGY IN UKRAINE: TOWARDS NATIONAL ECO ...

    African Journals Online (AJOL)

    RAYAN_

    on the renewable energy sources, including solar, wind, hydro, biomass and geothermal. It is emphasized that ... structures. Keywords: renewable ..... has three wind power plants with the capacity for 2; 2,5; and 3 MW, respectively. Its special ...

  5. Renewable Energy Potential for New Mexico

    Science.gov (United States)

    RE-Powering America's Land: Renewable Energy on Contaminated Land and Mining Sites was presented by Penelope McDaniel, during the 2008 Brown to Green: Make the Connection to Renewable Energy workshop.

  6. Renewable Energy Policy Fact sheet - Luxembourg

    International Nuclear Information System (INIS)

    2017-09-01

    The EurObserv'ER policy profiles give a snapshot of the renewable energy policy in the EU Member States. Main support instruments for incentivising electricity from renewable energy sources are feed-in tariffs and feed-in premiums. A subsidy instrument is used as well. Households operating small solar installations are entitled to tax benefits. Renewable heat production is promoted through four subsidy instruments. Renewable transport fuels are promoted by way of a bio-fuels blending quota scheme

  7. Renewable Resources, Capital Accumulation, and Economic Growth

    OpenAIRE

    Wei-Bin Zhang

    2011-01-01

    This paper proposes a dynamic economic model with physical capital and renewable resources. Different from most of the neoclassical growth models with renewable resources which are based on microeconomic foundation and neglect physical capital accumulation, this study proposes a growth model with dynamics of renewable resources and physical capital accumulation. The model is a synthesis of the neoclassical growth theory and the traditional dynamic models of renewable resources with an alterna...

  8. Renewable Energy Policy Fact sheet - Slovenia

    International Nuclear Information System (INIS)

    2017-07-01

    The EurObserv'ER policy profiles give a snapshot of the renewable energy policy in the EU Member States. In Slovenia, electricity from renewable sources is promoted through a feed-in tariff (so called 'guaranteed purchase') and a premium tariff (so called 'operating premium'), both granted through a tender procedure. Renewable energy sources for heating purposes are promoted mainly through loans on concessional terms and subsidies. The main incentive for renewable energy use in transport are tax exemptions and subsidies

  9. Renewables 2014. Global status report 2014

    International Nuclear Information System (INIS)

    Sawin, Janet L.; Sverrisson, Freyr; Chawla, Kanika; Lins, Christine; Adib, Rana; Hullin, Martin; Leitner, Sarah; Mazzaccaro, Stefano; Murdock, Hannah; Williamson, Laura E.; Wright, Glen; McCrone, Angus; Musolino, Evan; Mastny, Lisa; Lily Riahi; Sims, Ralph; Jonathan Skeen; Sverrisson, Freyr; Martinot, Eric

    2014-01-01

    The Renewables Global Status Report provides a comprehensive and timely overview of renewable energy market, industry, investment, and policy developments worldwide. It enables policy-makers, industry, investors, and civil society to make informed decisions. The report covers recent developments, current status, and key trends; by design, it does not provide analysis or forecast. The Renewables Global Status Report relies on up-to-date renewable energy data, provided by an international network of more than 500 contributors, researchers, and authors

  10. New narratives on Russian renewable energy policy

    International Nuclear Information System (INIS)

    Belyi, A.V.; Overland, I.

    2010-01-01

    The article points out the renewable energy potential in Russia in light of the new policy targets development, technical and economic potential as well as limits related to a lack of effectiveness of renewable energy promoting policies. Moreover, the article links the renewable energy development to the liberalization of Russian power sector which actually provides a possibility for market-support mechanisms, such as the green certificates. Renewable energy in Russia also has an important regional dimension, particularly for remote regions. (authors)

  11. Renewal after the punishment of free operant behavior.

    Science.gov (United States)

    Bouton, Mark E; Schepers, Scott T

    2015-01-01

    Three experiments examined the role of context in punishment learning. In Experiment 1, rats were trained to lever press for food in Context A and then punished for responding in Context B (by presenting response-contingent footshock). Punishment led to complete suppression of the response. However, when responding was tested (in extinction) in Contexts A and B, a strong renewal of responding occurred in Context A. In Experiment 2, renewal also occurred when initial reinforcement occurred in Context A, punishment occurred in Context B, and testing occurred in a new context (Context C). In both experiments, behavioral suppression and renewal were not observed in groups that received noncontingent (yoked) footshocks in Context B. In Experiment 3, 2 responses (lever press and chain pull) were separately reinforced in Contexts A and B and then punished in the opposite context. Although the procedure equated the contexts on their association with reinforcement and punishment, renewal of each response was observed when it was tested in its nonpunished context. The contexts also influenced response choice. Overall, the results suggest that punishment is specific to the context in which it is learned, and establish that its context-specificity does not depend on a simple association between the context and shock. Like extinction, punishment may involve learning to inhibit a specific response in a specific context. Implications for theories of punishment and for understanding the cessation of problematic operant behavior (e.g., drug abuse) are discussed. PsycINFO Database Record (c) 2015 APA, all rights reserved.

  12. Recent incentives for renewable energy in Turkey

    International Nuclear Information System (INIS)

    Simsek, Hayal Ayca; Simsek, Nevzat

    2013-01-01

    Recently, the importance of renewable energy sources has increased significantly as climate change has become an important long term threat to global ecosystems and the world economy. In the face of increased concern about climate change and high fossil fuel costs together with a reduction in the primary energy sources such as oil, natural gas and coal, alternative energy sources (renewables) are increasingly needed to respond to the threat of climate change and growing energy demand in the world. Recent developments in Turkey, such as the liberalization of the electricity market and improvements in the renewable legislations, have accelerated the growth process and investment opportunities in the field of renewable energy. Turkey′s naturally endowed potential for renewables, such as solar, geothermal and wind, also accompanied these developments and attracted world attention to this market. In Turkey, renewable energy sources have gained great importance in the last decades due to growing energy demand and incentive policies which foster the utilization of renewable energy sources. This study aims to explore the availability and potential of renewable energy sources in Turkey and discuss the government policies and economic aspects. - highlights: • Turkey′s potential for renewable energy has attracted world attention. • Turkey has specific energy objectives in promoting renewable energy. • This paper evaluates recent incentives for renewable energy in Turkey. • Incentives in Turkey have led to more investment in renewable energy generation

  13. Wind, hydro or mixed renewable energy source

    DEFF Research Database (Denmark)

    Yang, Yingkui; Solgaard, Hans Stubbe; Haider, Wolfgang

    2016-01-01

    While the share of renewable energy, especially wind power, increases in the energy mix, the risk of temporary energy shortage increases as well. Thus, it is important to understand consumers' preference for the renewable energy towards the continuous growing renewable energy society. We use...

  14. Renewable sources of energy in Austria 1993

    International Nuclear Information System (INIS)

    Faninger, G.

    1993-07-01

    Present contribution of renewable sources of energy to the overall energy requirements in Austria. Estimated potential of renewable sources of energy in Austria: firewood and biogeneous fuels, environmental energy, combustible wastes. Ecological aspects of utilising renewable sources of energy. Market barriers and strategies for overcoming them

  15. Financing Renewable Energy in the European Energy Market

    Energy Technology Data Exchange (ETDEWEB)

    De Jager, D.; Klessmann, C.; Stricker, E.; Winkel, T.; De Visser, E.; Koper, M. [Ecofys, Utrecht (Netherlands); Ragwitz, M.; Held, A. [Fraunhofer ISI, Karlsruhe (Germany); Resch, G.; Busch, S.; Panzer, C. [Energy Economics Group EEG, Vienna University of Technology, Vienna (Austria); Gazzo, A.; Roulleau, T.; Gousseland, P.; Henriet, M.; Bouille, A. [Ernst and Young, London (United Kingdom)

    2011-01-15

    The Directive 2009/28/EC on the promotion of the use of energy from renewable sources (RES) sets the overall target to reach 20% renewable energy in gross final energy consumption in 2020. This target is broken down into binding individual Member State targets. Reaching these targets will require a huge mobilization of investments in renewable energies in the coming decade. In order to improve financing and coordination with a view to the achievement of the 20 % target, Article 23 (7) of the Directive requires the Commission to present an analysis and action plan with a view to: (a) The better use of structural funds and framework programmes; (b) The better and increased use of funds from the European Investment Bank and other public finance institutions; (c) Better access to risk capital; (d) The better coordination of Community and national funding and other forms of support; (e) The better coordination in support of renewable energy initiatives whose success depends on action by actors in several Member States. This report presents the results of the title project. The study provides an up to date and thorough assessment of the costs of renewable energy and the support and financing instruments available for renewable energy R and D, demonstration projects and large-scale deployment. This includes details of each Member State's expenditure (via grants, support schemes, loans etc.) and use of Community funds, including loans of the EIB (European Investment Bank) and the EBRD (European Bank for Reconstruction and Development). It also explores the possible instruments for use in the future and constraints in the capital market, which hinder the development of renewable energy. Finally, it develops recommendations for improving financing and support instruments, improving the sector's access to capital, and closing the financing gap for reaching the 2020 targets. The chapters of the report represent separate tasks: (1) Costs of renewable energy

  16. Separated Flow over Wind Turbines

    Science.gov (United States)

    Brown, David; Lewalle, Jacques

    2015-11-01

    The motion of the separation point on an airfoil under unsteady flow can affect its performance and longevity. Of interest is to understand and control the performance decrease in wind turbines subject to turbulent flow. We examine flow separation on an airfoil at a 19 degree angle of attack under unsteady flow conditions. We are using a DU-96-W180 airfoil of chord length 242 mm. The unsteadiness is generated by a cylinder with diameter 203 mm located 7 diameters upstream of the airfoil's leading edge. The data comes from twenty surface pressure sensors located on the top and bottom of the airfoil as well as on the upstream cylinder. Methods of analysis include Mexican hat transforms, Morlet wavelet transforms, power spectra, and various cross correlations. With this study I will explore how the differences of signals on the pressure and suction sides of an airfoil are related to the motion of the separation point.

  17. Distinct DNA-binding surfaces in the ATPase and linker domains of MutLγ determine its substrate specificities and exert separable functions in meiotic recombination and mismatch repair.

    Directory of Open Access Journals (Sweden)

    Corentin Claeys Bouuaert

    2017-05-01

    Full Text Available Mlh1-Mlh3 (MutLγ is a mismatch repair factor with a central role in formation of meiotic crossovers, presumably through resolution of double Holliday junctions. MutLγ has DNA-binding, nuclease, and ATPase activities, but how these relate to one another and to in vivo functions are unclear. Here, we combine biochemical and genetic analyses to characterize Saccharomyces cerevisiae MutLγ. Limited proteolysis and atomic force microscopy showed that purified recombinant MutLγ undergoes ATP-driven conformational changes. In vitro, MutLγ displayed separable DNA-binding activities toward Holliday junctions (HJ and, surprisingly, single-stranded DNA (ssDNA, which was not predicted from current models. MutLγ bound DNA cooperatively, could bind multiple substrates simultaneously, and formed higher-order complexes. FeBABE hydroxyl radical footprinting indicated that the DNA-binding interfaces of MutLγ for ssDNA and HJ substrates only partially overlap. Most contacts with HJ substrates were located in the linker regions of MutLγ, whereas ssDNA contacts mapped within linker regions as well as the N-terminal ATPase domains. Using yeast genetic assays for mismatch repair and meiotic recombination, we found that mutations within different DNA-binding surfaces exert separable effects in vivo. For example, mutations within the Mlh1 linker conferred little or no meiotic phenotype but led to mismatch repair deficiency. Interestingly, mutations in the N-terminal domain of Mlh1 caused a stronger meiotic defect than mlh1Δ, suggesting that the mutant proteins retain an activity that interferes with alternative recombination pathways. Furthermore, mlh3Δ caused more chromosome missegregation than mlh1Δ, whereas mlh1Δ but not mlh3Δ partially alleviated meiotic defects of msh5Δ mutants. These findings illustrate functional differences between Mlh1 and Mlh3 during meiosis and suggest that their absence impinges on chromosome segregation not only via reduced

  18. Magnetic separation of algae

    Science.gov (United States)

    Nath, Pulak; Twary, Scott N.

    2016-04-26

    Described herein are methods and systems for harvesting, collecting, separating and/or dewatering algae using iron based salts combined with a magnetic field gradient to separate algae from an aqueous solution.

  19. Separation anxiety in children

    Science.gov (United States)

    ... page: //medlineplus.gov/ency/article/001542.htm Separation anxiety in children To use the sharing features on this page, please enable JavaScript. Separation anxiety in children is a developmental stage in which ...

  20. Chromatographic separations of stereoisomers

    Energy Technology Data Exchange (ETDEWEB)

    Souter, R.W.

    1985-01-01

    This text covers both diastereomers and enantiomers; describes techniques for GC, HPLC, and other chromatographic methods; and tabulates results of various applications by both techniques and compound class. It provides current knowledge about separation mechanisms and interactions of asymmetric molecules, as well as experimental and commercial materials such as columns, instruments, and derivatization reagents. The contents also include stereoisomer separations by gas chromatography. Stereoisomer separations by high-performance liquid chromatography. Stereoisomer separations by other chromatographic techniques.

  1. Inventor networks in renewable energies

    DEFF Research Database (Denmark)

    Cantner, Uwe; Graf, Holger; Herrmann, Johannes

    2016-01-01

    on patent data. Our results indicate notable differences between the technologies: the network size for wind power is driven by technology push and systemic instruments, while in photovoltaics, demand pull is decisive for network growth. By and large, the instruments complement each other and form...... energies. Our goal is to gain insights into the influence of this policy mix on the intensity and organization of inventive activities for wind power and photovoltaics in Germany since the 1980s. We examine the effect of different instruments on the size and structure of co-inventor networks based......Technological change and gains in efficiency of renewable power generation technologies are to a large extent driven by governmental support. Various policy instruments that can broadly be categorized as technology push, demand pull or systemic constitute part of the policy mix for renewable...

  2. Renewable gas French panorama 2017

    International Nuclear Information System (INIS)

    Leboul-Proust, Catherine; Nayral, Raphaelle; Pinel, Julie; Rabetsimamanga, Ony; Singly, Bertrand de; Garret, Mathilde; Saurin, Alice; Apolit, Robin; Billerey, Elodie; Flajollet-Millan, Johanna; Jouet, Francoise; Bock, Roger; Marron, Didier

    2018-03-01

    This publication first describes how biomethane is a gaseous renewable source of energy, by outlining how biogas production and biomethane injection into the network represent a solution for the reduction of greenhouse gas emissions, and by describing the different types of biomethane injection sites and the different types of inputs used to supply these sites. Then, after a presentation and a brief discussion of some key data regarding production and consumption, this publication presents the economic context, the regulatory framework, and a map of biomethane injection in Europe. The third part presents the fleet of biomethane injection installations in France, the characteristics of the connected sites, the regional distribution of the biomethane injection sector, and the production of biomethane injection installations. The fourth part discusses the growth perspectives of this sector by proposing an overview of planned injection projects, by assessing the potential production of methanization, and by addressing prospective issues on other ways of production of renewable gas

  3. Regulation - renewable energies finally liberated?

    International Nuclear Information System (INIS)

    Blosseville, Thomas

    2016-01-01

    Within the context defined by the new French policy for energy transition, notably in terms of share of renewable energies in final energy consumption, France seems to be somehow late in the development of these energies: about 1 GW of wind energy are installed each year when the expected pace would be 1,5 GW, and the photovoltaic market is shrinking. As the legal context is important, this article proposes an overview of the evolution of the French policy during the last four years which started with interesting measures. Recently, the government showed its will to liberate renewable energies from several constraints. Some legal procedures tend to slow down the development. Some advances could therefore be made, for example to make rules less complex and numerous. The different situations of the wind and biogas sectors are evoked, as well as new opportunities created by a new decree on investment planning

  4. Are renewable energies too expensive?

    International Nuclear Information System (INIS)

    2015-01-01

    As hydroelectricity is known to be profitable, and as biomass displayed good results when used for heating buildings, the issue of the cost of electricity produced by wind and photovoltaic energies is still a matter of debate. This article outlines how to take different factors into account to assess a discount rate. These factors are location which determines wind and sun resource, the future prices of fossil energies, rates of interest, and so on. It indicates that ground based wind and solar farms now have a kWh cost which is close to that of fossil energies, and lower than that of nuclear energy when taking investment and operation cost into account. The production cost of renewable energies has been dramatically reduced during the last years and this trend will probably continue during the years to come. Thus, the article states that a 100 per cent renewable mix seems possible for France by 2050 without significant over-costs

  5. Renewable gas French panorama 2016

    International Nuclear Information System (INIS)

    De Singly, Bertrand; Pinel, Julie; Garret, Mathilde; Schmit, Julien; Apolit, Robin; Bock, Roger; Pisani, Olivier; Marron, Didier

    2017-01-01

    This publication first describes how biomethane is a gaseous renewable source of energy, by outlining how biogas production and biomethane injection into the network represent a solution for the reduction of greenhouse gas emissions, and by describing the different types of biomethane injection sites and the different types of inputs used to supply these sites. Then, after a presentation and a brief discussion of some key data regarding production and consumption, this publication presents the economic context, the regulatory framework, and a map of biomethane injection in Europe. The third part presents the fleet of biomethane injection installations in France, the characteristics of the connected sites, the regional distribution of the biomethane injection sector, and the production of biomethane injection installations. The fourth part discusses the growth perspectives of this sector by proposing an overview of planned injection projects, by assessing the potential production of methanization, and by addressing prospective issues on other ways of production of renewable gas

  6. Photon Science for Renewable Energy

    International Nuclear Information System (INIS)

    Hussain, Zahid; Tamura, Lori; Padmore, Howard; Schoenlein, Bob; Bailey, Sue

    2010-01-01

    Our current fossil-fuel-based system is causing potentially catastrophic changes to our planet. The quest for renewable, nonpolluting sources of energy requires us to understand, predict, and ultimately control matter and energy at the electronic, atomic, and molecular levels. Light-source facilities - the synchrotrons of today and the next-generation light sources of tomorrow - are the scientific tools of choice for exploring the electronic and atomic structure of matter. As such, these photon-science facilities are uniquely positioned to jump-start a global revolution in renewable and carbonneutral energy technologies. In these pages, we outline and illustrate through examples from our nation's light sources possible scientific directions for addressing these profound yet urgent challenges.

  7. Wide angle isotope separator

    International Nuclear Information System (INIS)

    Kantrowitz, A.

    1976-01-01

    A method and apparatus is described for particle separation. The method uses a wide angle radially expanding vapor of a particle mixture. In particular, selective ionization of one isotope type in the particle mixture is produced in a multichamber separator and the ionized isotope type is accelerated out of the path of the vapor expansion for separate collection

  8. Steam-water separator

    International Nuclear Information System (INIS)

    Modrak, T.M.; Curtis, R.W.

    1978-01-01

    A two-stage steam-water separating device is introduced, where the second stage is made as a cyclone separator. The water separated here is collected in the first stage of the inner tube and is returned to the steam raising unit. (TK) [de

  9. Meniscus Membranes For Separation

    Science.gov (United States)

    Dye, Robert C.; Jorgensen, Betty; Pesiri, David R.

    2005-09-20

    Gas separation membranes, especially meniscus-shaped membranes for gas separations are disclosed together with the use of such meniscus-shaped membranes for applications such as thermal gas valves, pre-concentration of a gas stream, and selective pre-screening of a gas stream. In addition, a rapid screening system for simultaneously screening polymer materials for effectiveness in gas separation is provided.

  10. Meniscus membranes for separations

    Science.gov (United States)

    Dye, Robert C [Irvine, CA; Jorgensen, Betty [Jemez Springs, NM; Pesiri, David R [Aliso Viejo, CA

    2004-01-27

    Gas separation membranes, especially meniscus-shaped membranes for gas separations are disclosed together with the use of such meniscus-shaped membranes for applications such as thermal gas valves, pre-concentration of a gas stream, and selective pre-screening of a gas stream. In addition, a rapid screening system for simultaneously screening polymer materials for effectiveness in gas separation is provided.

  11. Renewables for Heating and Cooling

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2007-07-01

    This timely report examines the technologies, current markets and relative costs for heat and cold production using biomass, geothermal and solar-assisted systems. It evaluates a range of national case studies and relevant policies. Should the successful and more cost-effective policies be implemented by other countries, then the relatively untapped economic potential of renewable energy heating and cooling systems could be better realised, resulting in potential doubling of the present market within the next few years.

  12. Communicating a Renewed Brand Identity

    OpenAIRE

    Marttila, Oona

    2017-01-01

    This thesis aims to help the commissioning company in finding a suitable approach to efficiently communicate the renewed brand identity of the company. Theories applied to this research include rebranding, segmentation, as well as theories on customer relationships, service encounters and online marketing. This is complemented by the identification of the company potential through SWOT analysis as well as identifying differentiating factors within the company, in order to gain competitive adv...

  13. Moment convergence in renewal theory

    NARCIS (Netherlands)

    Iksanov, A.; Marynych, A.; Meiners, M.

    2012-01-01

    Let ¿1, ¿2, . . . be independent copies of a positive random variable ¿, and let Sk := ¿ 1 + . . . + ¿ k, k ¿ N0. Define N(t) := #{k ¿ N0 : Sk= t}. (N(t))t=0 is a renewal counting process. It is known that if ¿ is in the domain of attraction of a stable law of index a ¿ (1, 2], then N(t), suitably

  14. Customer choice and renewable energy

    Energy Technology Data Exchange (ETDEWEB)

    Schaefer, D.

    1996-12-31

    Opinions on political and social factors affecting the U.S. market for wind power are presented in this paper. The position of and activities taken by U.S. Congressman Dan Schaefer as Chairman of the House Energy and Power Subcommittee are outlined. Background information used as input to subcommittee hearings is summarized. The formation and activities of the House Renewable Energy Caucus are very briefly described.

  15. The potential of renewable energy

    International Nuclear Information System (INIS)

    Piot, M.

    2007-01-01

    This article presents and comments on definitions of the potential of renewable forms of energy and, in a second part, takes a look at the potentials mentioned in the energy perspectives published by the Swiss Federal Office of Energy (SFOE). The following potentials are looked at: technical potential, ecological potential, economic potential, exploitable and expected potentials, technical, economic and ecological expansion potentials, potential of particular technologies in Switzerland, exploitable and expected expansion potential. Four scenarios for expansion potential are briefly described

  16. Local investment in renewable energies

    International Nuclear Information System (INIS)

    Grepmeier, K.; Larsen, J.; Manolakaki, E.; Quantin, J.; Twele, J.

    2003-01-01

    This document presents european examples on the interest of the local investment, illustrated by cases studies in Germany, Denmark and Switzerland. Two main points were discussed: the financial tools and the french strategy. The colloquium provided many discussions and analyzes on the possibility of significant contribution to the collective efforts in favor of the public involvement in the renewable energies development in Europe. (A.L.B.)

  17. The economic impact of renewable energy

    International Nuclear Information System (INIS)

    1998-02-01

    This report summarises the findings of a project investigating the economic impact of renewable energy. The background to the study is traced, and potential sources of public finance for renewable projects, sensitivity analysis of the employment estimates , estimates of demand met by renewable energy technologies, the expenditures involved in investment in renewable energy; and sectoral linkages are examined. Wealth creation through investment in renewable energy, and the economic and employment impacts are explored. Plant retirement and replacement analysis, and input-output models are considered in appendices

  18. Renewable energy delivery systems and methods

    Science.gov (United States)

    Walker, Howard Andrew

    2013-12-10

    A system, method and/or apparatus for the delivery of energy at a site, at least a portion of the energy being delivered by at least one or more of a plurality of renewable energy technologies, the system and method including calculating the load required by the site for the period; calculating the amount of renewable energy for the period, including obtaining a capacity and a percentage of the period for the renewable energy to be delivered; comparing the total load to the renewable energy available; and, implementing one or both of additional and alternative renewable energy sources for delivery of energy to the site.

  19. Renewable Energy Policy Fact sheet - Sweden

    International Nuclear Information System (INIS)

    2017-09-01

    The EurObserv'ER policy profiles give a snapshot of the renewable energy policy in the EU Member States. Sweden surpassed its 2020 nationally binding renewable energy in 2013. Main support measures to promote renewable energy in Sweden consists of a quota system, various tax regulation mechanisms and subsidy schemes. Sweden has a joint support scheme with Norway, thus being the first EU Member State to implement a cooperation mechanism, as defined under the 2009 EU Renewable Energy Directive. The Swedish coalition government has agreed on a target of 100% renewable electricity production by 2040

  20. The economic impact of renewable energy

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-02-01

    This report summarises the findings of a project investigating the economic impact of renewable energy. The background to the study is traced, and potential sources of public finance for renewable projects, sensitivity analysis of the employment estimates , estimates of demand met by renewable energy technologies, the expenditures involved in investment in renewable energy; and sectoral linkages are examined. Wealth creation through investment in renewable energy, and the economic and employment impacts are explored. Plant retirement and replacement analysis, and input-output models are considered in appendices.