Dynamic Leidenfrost effect: relevant time- and length-scales
Shirota, Minori; Sun, Chao; Prosperetti, Andrea; Lohse, Detlef
2015-01-01
When a liquid droplet impacts a hot solid surface, enough vapor may be generated under it as to prevent its contact with the solid. The minimum solid temperature for this so-called Leidenfrost effect to occur is termed the Leidenfrost temperature, or the dynamic Leidenfrost temperature when the droplet velocity is non-negligible. We observe the wetting/drying and the levitation dynamics of the droplet impacting on an (isothermal) smooth sapphire surface using high speed total internal reflection imaging, which enables us to observe the droplet base up to about 100 nm above the substrate surface. By this method we are able to reveal the processes responsible for the transitional regime between the fully wetting and the fully levitated droplet as the solid temperature increases, thus shedding light on the characteristic time- and length-scales setting the dynamic Leidenfrost temperature for droplet impact on an isothermal substrate.
Harvey-Thompson, A. J.; Sefkow, A. B.; Wei, M. S.; Nagayama, T.; Campbell, E. M.; Blue, B. E.; Heeter, R. F.; Koning, J. M.; Peterson, K. J.; Schmitt, A.
2016-11-01
We report experimental results and simulations showing efficient laser energy coupling into plasmas at conditions relevant to the magnetized liner inertial fusion (MagLIF) concept. In MagLIF, to limit convergence and increase the hydrodynamic stability of the implosion, the fuel must be efficiently preheated. To determine the efficiency and physics of preheating by a laser, an Ar plasma with ne/nc r i t˜0.04 is irradiated by a multi-ns, multi-kJ, 0.35-μm, phase-plate-smoothed laser at spot-averaged intensities ranging from 1.0 ×1014 to 2.5 ×1014W /c m2 and pulse widths from 2 to 10 ns. Time-resolved x-ray images of the laser-heated plasma are compared to two-dimensional radiation-hydrodynamic simulations that show agreement with the propagating emission front, a comparison that constrains laser energy deposition to the plasma. The experiments show that long-pulse, modest-intensity (I =1.5 ×1014W /c m2 ) beams can efficiently couple energy (˜82 % of the incident energy) to MagLIF-relevant long-length (9.5 mm) underdense plasmas. The demonstrated heating efficiency is significantly higher than is thought to have been achieved in early integrated MagLIF experiments [A. B. Sefkow et al., Phys. Plasmas 21, 072711 (2014), 10.1063/1.4890298].
Rosenberg, M. J.; Solodov, A. A.; Seka, W.; Myatt, J. F.; Regan, S. P.; Hohenberger, M.; Epstein, R.; Froula, D. H.; Radha, P. B.; Michel, P. A.; Moody, J. D.; Masse, L.; Goyon, C.; Turnbull, D. P.; Barrios, M. A.; Bates, J. W.; Schmitt, A. J.
2016-10-01
The first experiments at the National Ignition Facility to probe laser-plasma interactions and the hot electron production at scale lengths relevant to direct-drive ignition are reported. The irradiation on one side of planar CH foils generated a plasma at the quarter-critical surface with predicted density scale lengths of Ln 600 μm, measured electron temperatures of Te 3.5 to 4.0 keV, and overlapped laser intensities of I 6 to 15 ×1014W/cm2. Optical emission from stimulated Raman scattering (SRS) and at ω/2 are correlated with the time-dependent hard x-ray signal. The fraction of laser energy converted to hot electrons increased from 0.5 % to 2.3 % as the laser intensity increased from 6 to 15 ×1014W/cm2, while the hot electron temperature was nearly constant around 40 to 50 keV. Only a sharp red-shifted feature is observed around ω/2, and both refracted and sidescattered SRS are detected, suggesting that multibeam SRS contributes to, and may even dominate, hot-electron production. These results imply a diminished presence of two-plasmon decay relative to SRS at these conditions, which has implications for hot-electron preheat mitigation strategies for direct-drive ignition. This work is supported by the DOE NNSA under Award Number DE-NA0001944.
IMF Length Scales and Predictability: The Two Length Scale Medium
Collier, Michael R.; Szabo, Adam; Slavin, James A.; Lepping, R. P.; Kokubun, S.
1999-01-01
We present preliminary results from a systematic study using simultaneous data from three spacecraft, Wind, IMP 8 (Interplanetary Monitoring Platform) and Geotail to examine interplanetary length scales and their implications on predictability for magnetic field parcels in the typical solar wind. Time periods were selected when the plane formed by the three spacecraft included the GSE (Ground Support Equipment) x-direction so that if the parcel fronts were strictly planar, the two adjacent spacecraft pairs would determine the same phase front angles. After correcting for the motion of the Earth relative to the interplanetary medium and deviations in the solar wind flow from radial, we used differences in the measured front angle between the two spacecraft pairs to determine structure radius of curvature. Results indicate that the typical radius of curvature for these IMF parcels is of the order of 100 R (Sub E). This implies that there are two important IMF (Interplanetary Magnetic Field) scale lengths relevant to predictability: (1) the well-established scale length over which correlations observed by two spacecraft decay along a given IMF parcel, of the order of a few tens of Earth radii and (2) the scale length over which two spacecraft are unlikely to even observe the same parcel because of its curvature, of the order of a hundred Earth radii.
Minimal Length Scale Scenarios for Quantum Gravity
Sabine Hossenfelder
2013-01-01
Full Text Available We review the question of whether the fundamental laws of nature limit our ability to probe arbitrarily short distances. First, we examine what insights can be gained from thought experiments for probes of shortest distances, and summarize what can be learned from different approaches to a theory of quantum gravity. Then we discuss some models that have been developed to implement a minimal length scale in quantum mechanics and quantum field theory. These models have entered the literature as the generalized uncertainty principle or the modified dispersion relation, and have allowed the study of the effects of a minimal length scale in quantum mechanics, quantum electrodynamics, thermodynamics, black-hole physics and cosmology. Finally, we touch upon the question of ways to circumvent the manifestation of a minimal length scale in short-distance physics.
Minimal Length Scale Scenarios for Quantum Gravity.
Hossenfelder, Sabine
2013-01-01
We review the question of whether the fundamental laws of nature limit our ability to probe arbitrarily short distances. First, we examine what insights can be gained from thought experiments for probes of shortest distances, and summarize what can be learned from different approaches to a theory of quantum gravity. Then we discuss some models that have been developed to implement a minimal length scale in quantum mechanics and quantum field theory. These models have entered the literature as the generalized uncertainty principle or the modified dispersion relation, and have allowed the study of the effects of a minimal length scale in quantum mechanics, quantum electrodynamics, thermodynamics, black-hole physics and cosmology. Finally, we touch upon the question of ways to circumvent the manifestation of a minimal length scale in short-distance physics.
Length-scale dependent phonon interactions
Srivastava, Gyaneshwar
2014-01-01
This book presents a comprehensive description of phonons and their interactions in systems with different dimensions and length scales. Internationally-recognized leaders describe theories and measurements of phonon interactions in relation to the design of materials with exotic properties such as metamaterials, nano-mechanical systems, next-generation electronic, photonic, and acoustic devices, energy harvesting, optical information storage, and applications of phonon lasers in a variety of fields. The emergence of techniques for control of semiconductor properties and geometry has enabled engineers to design structures in which functionality is derived from controlling electron behavior. As manufacturing techniques have greatly expanded the list of available materials and the range of attainable length scales, similar opportunities now exist for designing devices whose functionality is derived from controlling phonon behavior. However, progress in this area is hampered by gaps in our knowledge of phono...
Scale Length of the Galactic Thin Disk
D. Κ. Ojha
2000-06-01
This paper presents an analysis of the first 2MASS (The Two Micron All Sky Survey) sampler data as observed at lower Galactic latitude in our Galaxy. These new near-infrared data provide insight into the structure of the thin disk of our Galaxy, The interpretation of star counts and color distributions of stars in the near-infrared with the synthetic stellar population model, gives strong evidence that the Galactic thin disk density scale length, ℎ, is rather short (2.7 ± 0.1 kpc).
Optimal Length Scale for a Turbulent Dynamo.
Sadek, Mira; Alexakis, Alexandros; Fauve, Stephan
2016-02-19
We demonstrate that there is an optimal forcing length scale for low Prandtl number dynamo flows that can significantly reduce the required energy injection rate. The investigation is based on simulations of the induction equation in a periodic box of size 2πL. The flows considered are the laminar and turbulent ABC flows forced at different forcing wave numbers k_{f}, where the turbulent case is simulated using a subgrid turbulence model. At the smallest allowed forcing wave number k_{f}=k_{min}=1/L the laminar critical magnetic Reynolds number Rm_{c}^{lam} is more than an order of magnitude smaller than the turbulent critical magnetic Reynolds number Rm_{c}^{turb} due to the hindering effect of turbulent fluctuations. We show that this hindering effect is almost suppressed when the forcing wave number k_{f} is increased above an optimum wave number k_{f}L≃4 for which Rm_{c}^{turb} is minimum. At this optimal wave number, Rm_{c}^{turb} is smaller by more than a factor of 10 than the case forced in k_{f}=1. This leads to a reduction of the energy injection rate by 3 orders of magnitude when compared to the case where the system is forced at the largest scales and thus provides a new strategy for the design of a fully turbulent experimental dynamo.
Length Scales in Bayesian Automatic Adaptive Quadrature
Adam Gh.
2016-01-01
Full Text Available Two conceptual developments in the Bayesian automatic adaptive quadrature approach to the numerical solution of one-dimensional Riemann integrals [Gh. Adam, S. Adam, Springer LNCS 7125, 1–16 (2012] are reported. First, it is shown that the numerical quadrature which avoids the overcomputing and minimizes the hidden floating point loss of precision asks for the consideration of three classes of integration domain lengths endowed with specific quadrature sums: microscopic (trapezoidal rule, mesoscopic (Simpson rule, and macroscopic (quadrature sums of high algebraic degrees of precision. Second, sensitive diagnostic tools for the Bayesian inference on macroscopic ranges, coming from the use of Clenshaw-Curtis quadrature, are derived.
Length Scale of the Spin Seebeck Effect
Kehlberger, Andreas; Ritzmann, Ulrike; Hinzke, Denise; Guo, Er-Jia; Cramer, Joel; Jakob, Gerhard; Onbasli, Mehmet C.; Kim, Dong Hun; Ross, Caroline A.; Jungfleisch, Matthias B.; Hillebrands, Burkard; Nowak, Ulrich; Kläui, Mathias
2015-08-01
We investigate the origin of the spin Seebeck effect in yttrium iron garnet (YIG) samples for film thicknesses from 20 nm to 50 μ m at room temperature and 50 K. Our results reveal a characteristic increase of the longitudinal spin Seebeck effect amplitude with the thickness of the insulating ferrimagnetic YIG, which levels off at a critical thickness that increases with decreasing temperature. The observed behavior cannot be explained as an interface effect or by variations of the material parameters. Comparison to numerical simulations of thermal magnonic spin currents yields qualitative agreement for the thickness dependence resulting from the finite magnon propagation length. This allows us to trace the origin of the observed signals to genuine bulk magnonic spin currents due to the spin Seebeck effect ruling out an interface origin and allowing us to gauge the reach of thermally excited magnons in this system for different temperatures. At low temperature, even quantitative agreement with the simulations is found.
Imaging mass spectrometry at cellular length scales.
Altelaar, A F Maarten; Luxembourg, Stefan L; McDonnell, Liam A; Piersma, Sander R; Heeren, Ron M A
2007-01-01
Imaging mass spectrometry (IMS) allows the direct investigation of both the identity and the spatial distribution of the molecular content directly in tissue sections, single cells and many other biological surfaces. In this protocol, we present the steps required to retrieve the molecular information from tissue sections using matrix-enhanced (ME) and metal-assisted (MetA) secondary ion mass spectrometry (SIMS) as well as matrix-assisted laser desorption/ionization (MALDI) IMS. These techniques require specific sample preparation steps directed at optimal signal intensity with minimal redistribution or modification of the sample analytes. After careful sample preparation, different IMS methods offer a unique discovery tool in, for example, the investigation of (i) drug transport and uptake, (ii) biological processing steps and (iii) biomarker distributions. To extract the relevant information from the huge datasets produced by IMS, new bioinformatics approaches have been developed. The duration of the protocol is highly dependent on sample size and technique used, but on average takes approximately 5 h.
Minimum length scale in topology optimization by geometric constraints
Zhou, Mingdong; Lazarov, Boyan Stefanov; Wang, Fengwen
2015-01-01
A density-based topology optimization approach is proposed to design structures with strict minimum length scale. The idea is based on using a filtering-threshold topology optimization scheme and computationally cheap geometric constraints. The constraints are defined over the underlying structural...... geometry represented by the filtered and physical fields. Satisfying the constraints leads to a design that possesses user-specified minimum length scale. Conventional topology optimization problems can be augmented with the proposed constraints to achieve minimum length scale on the final design....... No additional finite element analysis is required for the constrained optimization. Several benchmark examples are presented to show the effectiveness of this approach....
Hydrodynamic length-scale selection in microswimmer suspensions
Heidenreich, Sebastian; Dunkel, Jörn; Klapp, Sabine H. L.; Bär, Markus
2016-08-01
A universal characteristic of mesoscale turbulence in active suspensions is the emergence of a typical vortex length scale, distinctly different from the scale invariance of turbulent high-Reynolds number flows. Collective length-scale selection has been observed in bacterial fluids, endothelial tissue, and active colloids, yet the physical origins of this phenomenon remain elusive. Here, we systematically derive an effective fourth-order field theory from a generic microscopic model that allows us to predict the typical vortex size in microswimmer suspensions. Building on a self-consistent closure condition, the derivation shows that the vortex length scale is determined by the competition between local alignment forces, rotational diffusion, and intermediate-range hydrodynamic interactions. Vortex structures found in simulations of the theory agree with recent measurements in Bacillus subtilis suspensions. Moreover, our approach yields an effective viscosity enhancement (reduction), as reported experimentally for puller (pusher) microorganisms.
Introducing artificial length scales to tailor magnetic properties
Fassbender, J; Strache, T; Liedke, M O; Marko, D; Wintz, S; Lenz, K; Keller, A; Facsko, S [Institute of Ion Beam Physics and Materials Research, Forschungszentrum Dresden-Rossendorf, PO Box 51 01 19, D-01314 Dresden (Germany); Moench, I; McCord, J [Leibniz Institute for Solid State and Materials Research IFW Dresden, PO Box 27 01 16, D-01171 Dresden (Germany)], E-mail: J.Fassbender@fzd.de
2009-12-15
Magnetism is a collective phenomenon. Hence, a local variation on the nanoscale of material properties, which act on the magnetic properties, affects the overall magnetism in an intriguing way. Of particular importance are the length scales on which a material property changes. These might be related to the exchange length, the domain wall width, a typical roughness correlation length, or a length scale introduced by patterning of the material. Here we report on the influence of two artificially created length scales: (i) ion erosion templates that serve as a source of a predefined surface morphology (ripple structure) and hence allow for the investigation of roughness phenomena. It is demonstrated that the ripple wave length can be easily tuned over a wide range (25-175 nm) by varying the primary ion erosion energy. The effect of this ripple morphology on the induced uniaxial magnetic anisotropy in soft magnetic Permalloy films is studied. Only below a ripple wavelength threshold ({approx}60 nm) is a significant induced magnetic anisotropy found. Above this threshold the corrugated Permalloy film acts as a flat film. This cross-over is discussed in the frame of dipolar interactions giving rise to the induced anisotropies. (ii) Ion implantation through a lithographically defined mask, which is used for a magnetic property patterning on various length scales. The resulting magnetic properties are neither present in non-implanted nor in homogeneously implanted films. Here new insight is gained by the comparison of different stripe patterning widths ranging from 1 to 10 {mu}m. In addition, the appearance of more complicated magnetic domain structures, i.e. spin-flop domain configurations and head-on domain walls, during hard axis magnetization reversal is demonstrated. In both cases the magnetic properties, the magnetization reversal process as well as the magnetic domain configurations depend sensitively on the artificially introduced length scale.
A multiple length scale description of the mechanism of elastomer stretching
Neuefeind, J.; Skov, Anne Ladegaard; Daniels, J. E.;
2016-01-01
Conventionally, the stretching of rubber is modeled exclusively by rotations of segments of the embedded polymer chains; i.e. changes in entropy. However models have not been tested on all relevant length scales due to a lack of appropriate probes. Here we present a universal X-ray based method...
Maximum length scale in density based topology optimization
Lazarov, Boyan Stefanov; Wang, Fengwen
2017-01-01
The focus of this work is on two new techniques for imposing maximum length scale in topology optimization. Restrictions on the maximum length scale provide designers with full control over the optimized structure and open possibilities to tailor the optimized design for broader range...... of manufacturing processes by fulfilling the associated technological constraints. One of the proposed methods is based on combination of several filters and builds on top of the classical density filtering which can be viewed as a low pass filter applied to the design parametrization. The main idea...
Length scales in cryogenic injection at supercritical pressure
Branam, R.; Mayer, W. [German Aerospace Center, DLR Lampoldshausen, 74239 Hardthausen (Germany)
2002-09-01
Length scales provide some understanding of the injection of cryogenic propellants in rocket chambers on mixing efficiency, which translates to burning efficiency and performance. This project uses supercritical cryogenic nitrogen to look at high-density core flows such as those of coaxial injectors used in rocket engines. The investigation considers test conditions from 4.0 to 6.0 MPa chamber pressure at two injection velocities and temperatures. Experimental data taken by using shadowgraph images provides a means of characterizing turbulent flow structures using a two-point correlation method to determine length scales and structure shapes. The experimental results are compared to computational models. (orig.)
Scaling carbon nanotube complementary transistors to 5-nm gate lengths
Qiu, Chenguang; Zhang, Zhiyong; Xiao, Mengmeng; Yang, Yingjun; Zhong, Donglai; Peng, Lian-Mao
2017-01-01
High-performance top-gated carbon nanotube field-effect transistors (CNT FETs) with a gate length of 5 nanometers can be fabricated that perform better than silicon complementary metal-oxide semiconductor (CMOS) FETs at the same scale. A scaling trend study revealed that the scaled CNT-based devices, which use graphene contacts, can operate much faster and at much lower supply voltage (0.4 versus 0.7 volts) and with much smaller subthreshold slope (typically 73 millivolts per decade). The 5-nanometer CNT FETs approached the quantum limit of FETs by using only one electron per switching operation. In addition, the contact length of the CNT CMOS devices was also scaled down to 25 nanometers, and a CMOS inverter with a total pitch size of 240 nanometers was also demonstrated.
A two-scale damage model with material length
Dascalu, Cristian
2009-09-01
The Note presents the formulation of a class of two-scale damage models involving a micro-structural length. A homogenization method based on asymptotic developments is employed to deduce the macroscopic damage equations. The damage model completely results from energy-based micro-crack propagation laws, without supplementary phenomenological assumptions. We show that the resulting two-scale model has the property of capturing micro-structural lengths. When damage evolves, the micro-structural length is given by the ratio of the surface density of energy dissipated during the micro-crack growth and the macroscopic damage energy release rate per unit volume of the material. The use of fracture criteria based on resistance curves or power laws for sub-critical growth of micro-cracks leads to quasi-brittle and, respectively, time-dependent damage models. To cite this article: C. Dascalu, C. R. Mecanique 337 (2009).
Length scales and selforganization in dense suspension flows
Düring, G.; Lerner, E.; Wyart, M.
2014-01-01
Dense non-Brownian suspension flows of hard particles display mystifying properties: As the jamming threshold is approached, the viscosity diverges, as well as a length scale that can be identified from velocity correlations. To unravel the microscopic mechanism governing dissipation and its
An inertial range length scale in structure functions
Kerr, R M; Gotoh, T; Kerr, Robert M.; Meneguzzi, Maurice; Gotoh, Toshiyuki
2000-01-01
It is shown using experimental and numerical data that within the traditional inertial subrange defined by where the third order structure function is linear that the higher order structure function scaling exponents for longitudinal and transverse structure functions converge only over larger scales, $r>r_S$, where $r_S$ has scaling intermediate between $\\eta$ and $\\lambda$ as a function of $R_\\lambda$. Below these scales, scaling exponents cannot be determined for any of the structure functions without resorting to procedures such as extended self-similarity (ESS). With ESS, different longitudinal and transverse higher order exponents are obtained that are consistent with earlier results. The relationship of these statistics to derivative and pressure statistics, to turbulent structures and to length scales is discussed.
Interacting length scales in the reactive-infiltration instability
Szymczak, Piotr
2013-01-01
The reactive-infiltration instability, which develops when a porous matrix is dissolved by a flowing fluid, contains two important length scales. Here we outline a linear stability analysis that simultaneously incorporates both scales. We show that the commonly used "thin-front" model is a limiting case of a more general theory, which also includes convection-dominated dissolution as another special case. The wavelength of the instability is bounded from below, and lies in the range 1mm to 1km for physically reasonable flow rates and reaction rates. We obtain a closed form for the growth rate when the change in porosity is small.
Proton conduction in exchange membranes across multiple length scales.
Jorn, Ryan; Savage, John; Voth, Gregory A
2012-11-20
Concerns over global climate change associated with fossil-fuel consumption continue to drive the development of electrochemical alternatives for energy technology. Proton exchange fuel cells are a particularly promising technology for stationary power generation, mobile electronics, and hybrid engines in automobiles. For these devices to work efficiently, direct electrical contacts between the anode and cathode must be avoided; hence, the separator material must be electronically insulating but highly proton conductive. As a result, researchers have examined a variety of polymer electrolyte materials for use as membranes in these systems. In the optimization of the membrane, researchers are seeking high proton conductivity, low electronic conduction, and mechanical stability with the inclusion of water in the polymer matrix. A considerable number of potential polymer backbone and side chain combinations have been synthesized to meet these requirements, and computational studies can assist in the challenge of designing the next generation of technologically relevant membranes. Such studies can also be integrated in a feedback loop with experiment to improve fuel cell performance. However, to accurately simulate the currently favored class of membranes, perfluorosulfonic acid containing moieties, several difficulties must be addressed including a proper treatment of the proton-hopping mechanism through the membrane and the formation of nanophase-separated water networks. We discuss our recent efforts to address these difficulties using methods that push the limits of computer simulation and expand on previous theoretical developments. We describe recent advances in the multistate empirical valence bond (MS-EVB) method that can probe proton diffusion at the nanometer-length scale and accurately model the so-called Grotthuss shuttling mechanism for proton diffusion in water. Using both classical molecular dynamics and coarse-grained descriptions that replace atomistic
Similarity theory based on the Dougherty-Ozmidov length scale
Grachev, Andrey A; Fairall, Christopher W; Guest, Peter S; Persson, P Ola G
2014-01-01
Local similarity theory is suggested based on the Brunt-Vaisala frequency and the dissipation rate of turbulent kinetic energy instead the turbulent fluxes used in the traditional Monin-Obukhov similarity theory. Based on dimensional analysis (Pi theorem), it is shown that any properly scaled statistics of the small-scale turbulence are universal functions of a stability parameter defined as the ratio of a reference height z and the Dougherty-Ozmidov length scale which in the limit of z-less stratification is linearly proportional to the Obukhov length scale. Measurements of atmospheric turbulence made at five levels on a 20-m tower over the Arctic pack ice during the Surface Heat Budget of the Arctic Ocean experiment (SHEBA) are used to examine the behaviour of different similarity functions in the stable boundary layer. It is found that in the framework of this approach the non-dimensional turbulent viscosity is equal to the gradient Richardson number whereas the non-dimensional turbulent thermal diffusivit...
On the damage and fracture of nuclear graphite at multiple length-scales
Liu, Dong; Mingard, Ken; Lord, Oliver T.; Flewitt, Peter
2017-09-01
Gilsocarbon graphite, as a neutron moderator and load-bearing component in the core of the UK fleet of Advanced Gas-Cooled Reactors, possesses complex microstructural features including defects/pores over a range of length-scales from nanometres to millimetres in size. As a consequence, this material exhibits different characteristics when specimens of different length-scale are deformed. In this work, the deformation and fracture of this material have been characterised using in situ methods for specimens of micrometre size (meso-scale) and the results are then compared with those measured one length-scale smaller, and those at the macro-scale. At the micro-scale, sampling a volume of material (2 × 2 × 10 μm) excludes micro- and macro-size pores, the strength was measured to be as high as 1000 MPa (an elastic modulus of about 67 GPa). When the specimen size is increased by one order of magnitude to the meso-scale, the strength is reduced to about 100 MPa (an elastic modulus of about 20 GPa) due to the inclusion of micro-size pores. For larger engineering-size specimens that include millimetre-size pores, the strength of the material averages about 20 MPa (an elastic modulus of about 11 GPa). This trend in the data is discussed and considered in the context of selecting the appropriate data for relevant multi-scale modelling.
Turbulence and entrainment length scales in large wind farms
Andersen, Søren Juhl; Sørensen, Jens Nørkær; Mikkelsen, Robert Flemming
2017-01-01
be taken into account when developing farm layouts. The self-organized motion or large coherent structures also yield high correlations between the power productions of consecutive turbines, which can be exploited through dynamic farm control.This article is part of the themed issue 'Wind energy in complex...... orthogonal decomposition, which is employed to detect the largest and most energetic coherent turbulent structures. The dominant length scales responsible for the entrainment process are shown to grow further into the wind farm, but to be limited in extent by the streamwise turbine spacing, which could...
Transition in multiple-scale-lengths turbulence in plasmas
Itoh, Sanae-I. [Kyushu Univ., Fukuoka (Japan). Research Inst. for Applied Mechanics; Itoh, Kimitaka [National Inst. for Fusion Science, Toki, Gifu (Japan)
2001-05-01
Statistical theory of strong turbulence in inhomogeneous plasmas is extended to the state where fluctuations with different scale lengths, micro and semi-micro modes, coexist. Their nonlinear interactions give several states of turbulence: in one state, the micro mode is excited while the semi-micro mode is quenched; in another state, the latter is excited while the micro mode is suppressed. A new turbulence transition with a hard bifurcation was obtained. A phase diagram was obtained. A new insight is given for the physics of internal transport barrier. (author)
Multi length-scale characterisation inorganic materials series
Bruce, Duncan W; Walton, Richard I
2013-01-01
Whereas the first five volumes in the Inorganic Materials Series focused on particular classes of materials (synthesis, structures, chemistry, and properties), it is now very timely to provide complementary volumes that introduce and review state-of-the-art techniques for materials characterization. This is an important way of emphasizing the interplay of chemical synthesis and physical characterization. The methods reviewed include spectroscopic, diffraction, and surface techniques that examine the structure of materials on all length scales, from local atomic structure to long-range crystall
Ashbaugh, H S; Ashbaugh, Henry S.; Pratt, Lawrence R.
2003-01-01
Hydrophobic hydration plays a crucial role in self-assembly processes over multiple-length scales, from the microscopic origins of inert gas solubility in water, to the mesoscopic organization of proteins and surfactant structures, to macroscopic phase separation. Many theoretical studies focus on the molecularly detailed interactions between oil and water, but the extrapolation of molecular-scale models to larger length scale hydration phenomena is sometimes not warranted. We revisit the scaled particle theory proposed thirty years ago by Stillinger, adopt a practical generalization, and consider the implications for hydrophobic hydration in light of our current understanding. The generalization is based upon identifying a molecular length, implicit in previous applications of scaled particle models, that provides an effective boundary radius for joining microscopic and macroscopic descriptions. We demonstrate that the generalized theory correctly reproduces many of the anomalous thermodynamic properties of ...
Spontaneous transmission of chirality through multiple length scales.
Iski, Erin V; Tierney, Heather L; Jewell, April D; Sykes, E Charles H
2011-06-20
The hierarchical transfer of chirality in nature, from the nano-, to meso-, to macroscopic length scales, is very complex, and as of yet, not well understood. The advent of scanning probes has allowed chirality to be monitored at the single molecule or monolayer level and has opened up the possibility to track enantiospecific interactions and chiral self-assembly with molecular-scale detail. This paper describes the self-assembly of a simple, model molecule (naphtho[2,3-a]pyrene) that is achiral in the gas phase, but becomes chiral when adsorbed on a surface. This polyaromatic hydrocarbon forms a stable and reversibly ordered system on Cu(111) in which the transmission of chirality from single surface-bound molecules to complex 2D chiral architectures can be monitored as a function of molecular packing density and surface temperature. In addition to the point chirality of the surface-bound molecule, the unit cell of the molecular domains was also found to be chiral due to the incommensurate alignment of the molecular rows with respect to the underlying metal lattice. These molecular domains always aggregated in groups of three, all of the same chirality, but with different rotational orientations, forming homochiral "tri-lobe" ensembles. At a larger length scale, these tri-lobe ensembles associated with nearest-neighbor tri-lobe units of opposite chirality at lower packing densities before forming an extended array of homochiral tri-lobe ensembles at higher converges. This system displayed chirality at a variety of size scales from the molecular (≈1 nm) and domain (≈5 nm) to the tri-lobe ensemble (≈10 nm) and extended array (>25 nm) levels. The chirality of the tri-lobe ensembles dictated how the overall surface packing occurred and both homo- and heterochiral arrays could be reproducibly and reversibly formed and interchanged as a function of surface coverage. Finally, these chirally templated surfaces displayed remarkable enantiospecificity for
The dynamics of rapid fracture: instabilities, nonlinearities and length scales.
Bouchbinder, Eran; Goldman, Tamar; Fineberg, Jay
2014-04-01
The failure of materials and interfaces is mediated by cracks, almost singular dissipative structures that propagate at velocities approaching the speed of sound. Crack initiation and subsequent propagation-the dynamic process of fracture-couples a wide range of time and length scales. Crack dynamics challenge our understanding of the fundamental physics processes that take place in the extreme conditions within the almost singular region where material failure occurs. Here, we first briefly review the classic approach to dynamic fracture, namely linear elastic fracture mechanics (LEFM), and discuss its successes and limitations. We show how, on the one hand, recent experiments performed on straight cracks propagating in soft brittle materials have quantitatively confirmed the predictions of this theory to an unprecedented degree. On the other hand, these experiments show how LEFM breaks down as the singular region at the tip of a crack is approached. This breakdown naturally leads to a new theoretical framework coined 'weakly nonlinear fracture mechanics', where weak elastic nonlinearities are incorporated. The stronger singularity predicted by this theory gives rise to a new and intrinsic length scale, ℓnl. These predictions are verified in detail through direct measurements. We then theoretically and experimentally review how the emergence of ℓnl is linked to a new equation for crack motion, which predicts the existence of a high-speed oscillatory crack instability whose wavelength is determined by ℓnl. We conclude by delineating outstanding challenges in the field.
Spatial length scales of large-scale structures in atmospheric surface layers
Liu, HongYou; Wang, GuoHua; Zheng, XiaoJing
2017-06-01
Synchronous multipoint measurements were performed in the atmospheric surface layer at the Qingtu Lake Observation Array site to obtain high-Reynolds-number [Reτ˜O (106) ] data. Based on the selected high-quality data in the near-neutral surface layer, the spatial length scales of the large-scale dominant structures in the outer region of the turbulent boundary layer are investigated. The characteristic length scales are extracted from the two-point streamwise velocity correlations. Results show that the spatial length scales are invariant over a three order of magnitude change in Reynolds number [Reτ˜O (103) -O (106) ] . However, they increase significantly with the wall-normal distance, showing reasonable collapses on outer-scaled axes. The variation of the spanwise width scale in the logarithmic region follows a linear increase, with the rate of increase much larger than that in the wake region. Moreover, the variation of the wall-normal length scale is also revealed, which displays a qualitative behavior similar to that of the spanwise width scale. The universal laws revealed in the present work contribute to a better understanding of the dominant structures in the outer region of the turbulent boundary layer at high Reynolds numbers.
Kalaitzaki, Eleftheria; White, Ian R; Khadjesari, Zarnie; Murray, Elizabeth; Linke, Stuart; Thompson, Simon G; Godfrey, Christine; Wallace, Paul
2011-01-01
Background There has been limited study of factors influencing response rates and attrition in online research. Online experiments were nested within the pilot (study 1, n = 3780) and main trial (study 2, n = 2667) phases of an evaluation of a Web-based intervention for hazardous drinkers: the Down Your Drink randomized controlled trial (DYD-RCT). Objectives The objective was to determine whether differences in the length and relevance of questionnaires can impact upon loss to follow-up in online trials. Methods A randomized controlled trial design was used. All participants who consented to enter DYD-RCT and completed the primary outcome questionnaires were randomized to complete one of four secondary outcome questionnaires at baseline and at follow-up. These questionnaires varied in length (additional 23 or 34 versus 10 items) and relevance (alcohol problems versus mental health). The outcome measure was the proportion of participants who completed follow-up at each of two follow-up intervals: study 1 after 1 and 3 months and study 2 after 3 and 12 months. Results At all four follow-up intervals there were no significant effects of additional questionnaire length on follow-up. Randomization to the less relevant questionnaire resulted in significantly lower rates of follow-up in two of the four assessments made (absolute difference of 4%, 95% confidence interval [CI] 0%-8%, in both study 1 after 1 month and in study 2 after 12 months). A post hoc pooled analysis across all four follow-up intervals found this effect of marginal statistical significance (unadjusted difference, 3%, range 1%-5%, P = .01; difference adjusted for prespecified covariates, 3%, range 0%-5%, P = .05). Conclusions Apparently minor differences in study design decisions may have a measurable impact on attrition in trials. Further investigation is warranted of the impact of the relevance of outcome measures on follow-up rates and, more broadly, of the consequences of what we ask participants to
Minimum description length methods of medium-scale simultaneous inference
Bickel, David R
2010-01-01
Nonparametric statistical methods developed for analyzing data for high numbers of genes, SNPs, or other biological features tend to overfit data with smaller numbers of features such as proteins, metabolites, or, when expression is measured with conventional instruments, genes. For this medium-scale inference problem, the minimum description length (MDL) framework quantifies the amount of information in the data supporting a null or alternative hypothesis for each feature in terms of parametric model selection. Two new MDL techniques are proposed. First, using test statistics that are highly informative about the parameter of interest, the data are reduced to a single statistic per feature. This simplifying step is already implicit in conventional hypothesis testing and has been found effective in empirical Bayes applications to genomics data. Second, the codelength difference between the alternative and null hypotheses of any given feature can take advantage of information in the measurements from all other...
DHS Internship Summary-Crystal Assembly at Different Length Scales
Mishchenko, L
2009-08-06
I was part of a project in which in situ atomic force microscopy (AFM) was used to monitor growth and dissolution of atomic and colloidal crystals. At both length scales, the chemical environment of the system greatly altered crystal growth and dissolution. Calcium phosphate was used as a model system for atomic crystals. A dissolution-reprecipitation reaction was observed in this first system, involving the conversion of brushite (DCPD) to octacalcium phosphate (OCP). In the second system, polymeric colloidal crystals were dissolved in an ionic solvent, revealing the underlying structure of the crystal. The dissolved crystal was then regrown through an evaporative step method. Recently, we have also found that colloids can be reversibly deposited in situ onto an ITO (indium tin oxide) substrate via an electrochemistry setup. The overall goal of this project was to develop an understanding of the mechanisms that control crystallization and order, so that these might be controlled during material synthesis. Controlled assembly of materials over a range of length scales from molecules to nanoparticles to colloids is critical for designing new materials. In particular, developing materials for sensor applications with tailorable properties and long range order is important. In this work, we examine two of these length scales: small molecule crystallization of calcium phosphate (whose crystal phases include DCPD, OCP, and HAP) and colloidal crystallization of Poly(methyl methacrylate) beads. Atomic Force Microscopy is ideal for this line of work because it allows for the possibility of observing non-conducting samples in fluid during growth with high resolution ({approx} 10 nm). In fact, during atomic crystal growth one can observe changes in atomic steps, and with colloidal crystals, one can monitor the individual building blocks of the crystal. Colloids and atoms crystallize under the influence of different forces acting at different length scales as seen in Table 1
Turbulence and entrainment length scales in large wind farms
Andersen, Søren J.; Sørensen, Jens N.; Mikkelsen, Robert F.
2017-03-01
A number of large wind farms are modelled using large eddy simulations to elucidate the entrainment process. A reference simulation without turbines and three farm simulations with different degrees of imposed atmospheric turbulence are presented. The entrainment process is assessed using proper orthogonal decomposition, which is employed to detect the largest and most energetic coherent turbulent structures. The dominant length scales responsible for the entrainment process are shown to grow further into the wind farm, but to be limited in extent by the streamwise turbine spacing, which could be taken into account when developing farm layouts. The self-organized motion or large coherent structures also yield high correlations between the power productions of consecutive turbines, which can be exploited through dynamic farm control. This article is part of the themed issue 'Wind energy in complex terrains'.
Density Functional Theory and Materials Modeling at Atomistic Length Scales
Swapan K. Ghosh
2002-04-01
Full Text Available Abstract: We discuss the basic concepts of density functional theory (DFT as applied to materials modeling in the microscopic, mesoscopic and macroscopic length scales. The picture that emerges is that of a single unified framework for the study of both quantum and classical systems. While for quantum DFT, the central equation is a one-particle Schrodinger-like Kohn-Sham equation, the classical DFT consists of Boltzmann type distributions, both corresponding to a system of noninteracting particles in the field of a density-dependent effective potential, the exact functional form of which is unknown. One therefore approximates the exchange-correlation potential for quantum systems and the excess free energy density functional or the direct correlation functions for classical systems. Illustrative applications of quantum DFT to microscopic modeling of molecular interaction and that of classical DFT to a mesoscopic modeling of soft condensed matter systems are highlighted.
Cooperative length scale of Aroclor near its dynamic glass transition
Rizos, A.K. [Univ. of Crete, Heraklion (Greece); Ngai, K.L. [Naval Research Lab., Washington, DC (United States)
1997-12-31
Photon correlation spectroscopy in the depolarized mode has been used to monitor the reorientational dynamics of Aroclor (A1248) (polychlorinated biphenyls) that contain in solutions various amounts of low and high molecular weight (M{sub W}) polymers. For the high M{sub W} polymer/A1248 solutions the authors observe a very small dependence of the stretched exponential parameter {beta} on temperature. In contrast, the low M{sub W} polymer/A1248 solutions display a pronounced temperature dependence of {beta}. These preliminary experiments allow them to use the effect of modification of the solvent dynamics by added polymer to estimate the length scale of cooperative motion in glass forming systems from the size of the polymer chain.
Turbulence and entrainment length scales in large wind farms.
Andersen, Søren J; Sørensen, Jens N; Mikkelsen, Robert F
2017-04-13
A number of large wind farms are modelled using large eddy simulations to elucidate the entrainment process. A reference simulation without turbines and three farm simulations with different degrees of imposed atmospheric turbulence are presented. The entrainment process is assessed using proper orthogonal decomposition, which is employed to detect the largest and most energetic coherent turbulent structures. The dominant length scales responsible for the entrainment process are shown to grow further into the wind farm, but to be limited in extent by the streamwise turbine spacing, which could be taken into account when developing farm layouts. The self-organized motion or large coherent structures also yield high correlations between the power productions of consecutive turbines, which can be exploited through dynamic farm control.This article is part of the themed issue 'Wind energy in complex terrains'.
Structural and cooperative length scales in polymer gels.
Géraud, Baudouin; Jørgensen, Loren; Ybert, Christophe; Delanoë-Ayari, Hélène; Barentin, Catherine
2017-01-01
Understanding the relationship between the material structural details, the geometrical confining constraints, the local dynamical events and the global rheological response is at the core of present investigations on complex fluid properties. In the present article, this problem is addressed on a model yield stress fluid made of highly entangled polymer gels of Carbopol which follows at the macroscopic scale the well-known Herschel-Bulkley rheological law. First, performing local rheology measurements up to high shear rates ([Formula: see text] s(-1))and under confinement, we evidence unambiguously the breakdown of bulk rheology associated with cooperative processes under flow. Moreover, we show that these behaviors are fully captured with a unique cooperativity length [Formula: see text] over the whole range of experimental conditions. Second, we introduce an original optical microscopy method to access structural properties of the entangled polymer gel in the direct space. Performing image correlation spectroscopy of fluorophore-loaded gels, the characteristic size D of carbopol gels microstructure is determined as a function of preparation protocol. Combining both dynamical and structural information shows that the measured cooperative length [Formula: see text] corresponds to 2-5 times the underlying structural size D, thus providing a strong grounding to the "Shear Transformation Zones" modeling approach.
Modelling Time and Length Scales of Scour Around a Pipeline
Smith, H. D.; Foster, D. L.
2002-12-01
The scour and burial of submarine objects is an area of interest for engineers, oceanographers and military personnel. Given the limited availability of field observations, there exists a need to accurately describe the hydrodynamics and sediment response around an obstacle using numerical models. In this presentation, we will compare observations of submarine pipeline scour with model predictions. The research presented here uses the computational fluid dynamics (CFD) model FLOW-3D. FLOW-3D, developed by Flow Science in Santa Fe, NM, is a 3-dimensional finite-difference model that solves the Navier-Stokes and continuity equations. Using the Volume of Fluid (VOF) technique, FLOW-3D is able to resolve fluid-fluid and fluid-air interfaces. The FAVOR technique allows for complex geometry to be resolved with rectangular grids. FLOW-3D uses a bulk transport method to describe sediment transport and feedback to the hydrodynamic solver is accomplished by morphology evolution and fluid viscosity due to sediment suspension. Previous investigations by the authors have shown FLOW-3D to well-predict the hydrodynamics around five static scoured bed profiles and a stationary pipeline (``Modelling of Flow Around a Cylinder Over a Scoured Bed,'' submit to Journal of Waterway, Port, Coastal, and Ocean Engineering). Following experiments performed by Mao (1986, Dissertation, Technical University of Denmark), we will be performing model-data comparisons of length and time scales for scour around a pipeline. Preliminary investigations with LES and k-ɛ closure schemes have shown that the model predicts shorter time scales in scour hole development than that observed by Mao. Predicted time and length scales of scour hole development are shown to be a function of turbulence closure scheme, grain size, and hydrodynamic forcing. Subsequent investigations consider variable wave-current flow regimes and object burial. This investigation will allow us to identify different regimes for the
Fault zone rheology and length scales of frictional failure
Fagereng, A.
2011-12-01
Faults have a finite thickness and commonly contain fault rocks of heterogeneous composition, leading to rheological contrasts between intermingled lithologies (at the macroscale) and minerals (at the microscale) within the fault zone. The distribution and volumetric ratio of materials with different viscosity, frictional behavior, and preferred deformation mechanism, may therefore be a critical factor controlling the bulk rheology of heterogeneous fault zones. For example, at subgreenschist facies metamorphic conditions, fine-grained phyllosilicate-dominated mudstones tend to experience viscous shearing flow by dissolution-precipitation creep, whereas coarse grained quartz-dominated sandstones tend to act like competent, brittle volumes. In the rock record, deformation of mixed lithologies is well represented in tectonic mélanges. The subgreenschist facies (P defined by slickenfibre-coated shear surfaces linked by quartz-calcite extension veins. The frequency-size distribution of competent lenses (phacoids) in the Chrystalls Beach Complex follows a power-law distribution and is scale-invariant. The exponent of the power-law distribution varies with dominant deformation style, and is high in zones of dominantly continuous deformation - relating to a high matrix fraction, predominance of small phacoids, and small phacoid aspect ratios, whereas a low power-law exponent relates to a small matrix fraction and localized deformation accommodated on shear discontinuities. This variation in power-law exponent indicates that whether deformation occurs predominantly by continuous or discontinuous deformation may be predicted from the shape of the frequency-size distribution of competent lenses, and supports the hypothesis that bulk rheology is determined by the volume fraction of competent material. The distribution of competent material likely affects the seismic style of actively deforming fault zones. The length scales of shear discontinuities are likely to be a factor
Measuring Biological Parameters in Rivers: Relevance of the Spatial Scale
Romani, A. M.
2009-07-01
The analyses of biological parameters in river ecosystems have been traditionally used as indicative of water quality with the advantage over chemical or physical analyses that they integrate the effects of punctual as well as long term effects. However, analyses of biological parameters (such as biomass and metabolism) performed at different spatial scales (from the microbial communities to the whole river) inform about different key processes. At the finer scale, microbial interactions and the structure of the microbial community (biofilm microbial biomass, three dimensional structure, and relevance of polysaccharide matrix) can be detected. At the reach scale, the different stream bed substrate (sediment, rocks, and particulate organic matter accumulation) are shown to play differential and specific roles on the processing of organic and inorganic materials in the flowing water. (Author)
A multiple length scale description of the mechanism of elastomer stretching
Neuefeind, J.; Skov, Anne Ladegaard; Daniels, J. E.
2016-01-01
Conventionally, the stretching of rubber is modeled exclusively by rotations of segments of the embedded polymer chains; i.e. changes in entropy. However models have not been tested on all relevant length scales due to a lack of appropriate probes. Here we present a universal X-ray based method...... within the individual monomers, but among the contributions is also an elastic strain, acting between chains, which is 3-4 orders of magnitude smaller than the macroscopic strain, and of the opposite sign, i.e. extension of polymer chains in the direction perpendicular to the stretch. This may be due...
The distribution of length scales generated by mixing processes in time-p eriodic chaotic flows
Muzzio, Fernando; Alvarez, Mario; Cerbelli, Stefano
1997-11-01
This talk explores in some detail the evolution of the spatial structure and th e statistical properties of partially mixed systems as they evolve on a torus by using a direct numerical simulation of the evolution of continuous material lin es as they are stretched, reoriented, and folded by the flow. In the time scale s of interest to mixing processes, such material lines grow exponentially fast, but much faster than predicted by the Lyapunov exponent. The filament develops into a self-similar structure; frequency distribution of filament densities corr esponding to different times collapses onto an invariant curve by a simple homog eneous scaling. It is shown that this behavior is a direct consequence of a gen eric asymptotic directionality property characteristic of 2D time-periodic flows . Mixture microstructure is also analyzed by computing the evolution of th e distribution of length scales in the flow. Once again, the result is a family of self-similar curves that scale homogeneously by the mean length scale, which collapses in inverse proportion to the rate of growth of the filament. It is s hown that this rate of collapse, which has direct relevance to mixing applicatio ns, can be accurately and straightforwardly predicted from the ergodic average o f the stretching field. Implications for mixing processes in realistic systems are also discussed.
Optically controlled thermal management on the nanometer length scale
Garwe, F [Institute of Photonic Technology (IPHT) Jena, PO Box 100239, D-07745 Jena (Germany); Bauerschaefer, U [GmBU, Erich-Neuss-Weg 5, D-06120 Halle/S (Germany); Csaki, A [Institute of Photonic Technology (IPHT) Jena, PO Box 100239, D-07745 Jena (Germany); Steinbrueck, A [Institute of Photonic Technology (IPHT) Jena, PO Box 100239, D-07745 Jena (Germany); Ritter, K [Technical University Ilmenau, D-98693 Ilmenau (Germany); Bochmann, A [Institute of Photonic Technology (IPHT) Jena, PO Box 100239, D-07745 Jena (Germany); Bergmann, J [Institute of Photonic Technology (IPHT) Jena, PO Box 100239, D-07745 Jena (Germany); Weise, A [Friedrich Schiller University Jena, Institute of Human Genetics and Anthropology, D-07702 Jena (Germany); Akimov, D [Friedrich Schiller University Jena, Institute of Physical Chemistry, D-07743 Jena (Germany); Maubach, G [Institute of Photonic Technology (IPHT) Jena, PO Box 100239, D-07745 Jena (Germany); Koenig, K [Fraunhofer Institut St Ingbert, D-07702 St Ingbert (Germany); Huettmann, G [Medical Laser Center Luebeck, D-23552 Luebeck (Germany); Paa, W [Institute of Photonic Technology (IPHT) Jena, PO Box 100239, D-07745 Jena (Germany); Popp, J [Institute of Photonic Technology (IPHT) Jena, PO Box 100239, D-07745 Jena (Germany); Fritzsche, W [Institute of Photonic Technology (IPHT) Jena, PO Box 100239, D-07745 Jena (Germany)
2008-02-06
The manipulation of polymers and biological molecules or the control of chemical reactions on a nanometer scale by means of laser pulses shows great promise for applications in modern nanotechnology, biotechnology, molecular medicine or chemistry. A controllable, parallel, highly efficient and very local heat conversion of the incident laser light into metal nanoparticles without ablation or fragmentation provides the means for a tool like a 'nanoreactor', a 'nanowelder', a 'nanocrystallizer' or a 'nanodesorber'. In this paper we explain theoretically and show experimentally the interaction of laser radiation with gold nanoparticles on a polymethylmethacrylate (PMMA) layer (one-photon excitation) by means of different laser pulse lengths, wavelengths and pulse repetition rates. To the best of our knowledge this is the first report showing the possibility of highly local (in a 40 nm range) regulated heat insertion into the nanoparticle and its surroundings without ablation of the gold nanoparticles. In an earlier paper we showed that near-infrared femtosecond irradiation can cut labeled DNA sequences in metaphase chromosomes below the diffraction-limited spot size. Now, we use gold as well as silver-enhanced gold nanoparticles on DNA (also within chromosomes) as energy coupling objects for femtosecond laser irradiation with single-and two-photon excitation. We show the results of highly localized destruction effects on DNA that occur only nearby the nanoparticles.
Broadband dielectric microwave microscopy on micron length scales.
Tselev, Alexander; Anlage, Steven M; Ma, Zhengkun; Melngailis, John
2007-04-01
We demonstrate that a near-field microwave microscope based on a transmission line resonator allows imaging in a substantially wide range of frequencies, so that the microscope properties approach those of a spatially resolved impedance analyzer. In the case of an electric probe, the broadband imaging can be used in a direct fashion to separate contributions from capacitive and resistive properties of a sample at length scales on the order of one micron. Using a microwave near-field microscope based on a transmission line resonator we imaged the local dielectric properties of a focused ion beam milled structure on a high-dielectric-constant Ba(0.6)Sr(0.4)TiO(3) thin film in the frequency range from 1.3 to 17.4 GHz. The electrostatic approximation breaks down already at frequencies above approximately 10 GHz for the probe geometry used, and a full-wave analysis is necessary to obtain qualitative information from the images.
Model of a fluid at small and large length scales and the hydrophobic effect
tenWolde, Pieter Rein; Sun, Sean X.; Chandler, David
2001-01-01
We present a statistical field theory to describe large length scale effects induced by solutes in a cold and otherwise placid liquid. The theory divides space into a cubic grid of cells. The side length of each cell is of the order of the bulk correlation length of the bulk liquid. Large length scale states of the cells are specified with an Ising variable. Finer length scale effects are described with a Gaussian field, with mean and variance affected by both the large length scale field and...
Exploring heavy fermions from macroscopic to microscopic length scales
Wirth, Steffen; Steglich, Frank
2016-10-01
Strongly correlated systems present fundamental challenges, especially in materials in which electronic correlations cause a strong increase of the effective mass of the charge carriers. Heavy fermion metals — intermetallic compounds of rare earth metals (such as Ce, Sm and Yb) and actinides (such as U, Np and Pu) — are prototype systems for complex and collective quantum states; they exhibit both a lattice Kondo effect and antiferromagnetic correlations. These materials show unexpected phenomena; for example, they display unconventional superconductivity (beyond Bardeen-Cooper-Schrieffer (BCS) theory) and unconventional quantum criticality (beyond the Landau framework). In this Review, we focus on systems in which Landau's Fermi-liquid theory does not apply. Heavy fermion metals and semiconductors are well suited for the study of strong electronic correlations, because the relevant energy scales (for charge carriers, magnetic excitations and lattice dynamics) are well separated from each other, allowing the exploration of concomitant physical phenomena almost independently. Thus, the study of these materials also provides valuable insight for the understanding — and tailoring — of other correlated systems.
Inlet Turbulence and Length Scale Measurements in a Large Scale Transonic Turbine Cascade
Thurman, Douglas; Flegel, Ashlie; Giel, Paul
2014-01-01
Constant temperature hotwire anemometry data were acquired to determine the inlet turbulence conditions of a transonic turbine blade linear cascade. Flow conditions and angles were investigated that corresponded to the take-off and cruise conditions of the Variable Speed Power Turbine (VSPT) project and to an Energy Efficient Engine (EEE) scaled rotor blade tip section. Mean and turbulent flowfield measurements including intensity, length scale, turbulence decay, and power spectra were determined for high and low turbulence intensity flows at various Reynolds numbers and spanwise locations. The experimental data will be useful for establishing the inlet boundary conditions needed to validate turbulence models in CFD codes.
Energy dependent transport length scales in strongly diffusive carbon nanotubes
Lassagne, B [Laboratoire National des Champs Magnetiques Pulses, UMR5147 143 avenida de rangueil, 31400 Toulouse (France); Raquet, B [Laboratoire National des Champs Magnetiques Pulses, UMR5147 143 avenida de rangueil, 31400 Toulouse (France); Broto, J M [Laboratoire National des Champs Magnetiques Pulses, UMR5147 143 avenida de rangueil, 31400 Toulouse (France); Gonzalez, J [Centro de Estudios de Semiconductores Facultad de Ciencias, Departamento de Fisica, Universidad de Los Andes, Merida (Venezuela)
2006-05-17
We report magneto-transport measurements in parallel magnetic field and {mu}-Raman spectroscopy on diffusive multiwall carbon nanotubes. The disorder effects on the characteristic transport lengths are probed by combining applied magnetic field and back-gate tuning of the Fermi level. Modulations of the differential conductance versus energy depict the modulation of the strength of the weak localization. Both the electronic mean free path and the phase coherence length are found to be energy dependent. The role of disorder in the density of states and in the characteristic transport lengths is discussed.
Physics on Smallest Scales - An Introduction to Minimal Length Phenomenology
Sprenger, Martin; Bleicher, Marcus
2012-01-01
Many modern theories which try to unite gravity with the Standard Model of particle physics, as e.g. string theory, propose two key modifications to the commonly known physical theories: i) the existence of additional space dimensions; ii) the existence of a minimal length distance or maximal resolution. While extra dimensions have received a wide coverage in publications over the last ten years (especially due to the prediction of micro black hole production at the LHC), the phenomenology of models with a minimal length is still less investigated. In a summer study project for bachelor students in 2010 we have explored some phenomenological implications of the potential existence of a minimal length. In this paper we review the idea and formalism of a quantum gravity induced minimal length in the generalised uncertainty principle framework as well as in the coherent state approach to non-commutative geometry. These approaches are effective models which can make model-independent predictions for experiments a...
Time and length scales within a fire and implications for numerical simulation
TIESZEN,SHELDON R.
2000-02-02
A partial non-dimensionalization of the Navier-Stokes equations is used to obtain order of magnitude estimates of the rate-controlling transport processes in the reacting portion of a fire plume as a function of length scale. Over continuum length scales, buoyant times scales vary as the square root of the length scale; advection time scales vary as the length scale, and diffusion time scales vary as the square of the length scale. Due to the variation with length scale, each process is dominant over a given range. The relationship of buoyancy and baroclinc vorticity generation is highlighted. For numerical simulation, first principles solution for fire problems is not possible with foreseeable computational hardware in the near future. Filtered transport equations with subgrid modeling will be required as two to three decades of length scale are captured by solution of discretized conservation equations. By whatever filtering process one employs, one must have humble expectations for the accuracy obtainable by numerical simulation for practical fire problems that contain important multi-physics/multi-length-scale coupling with up to 10 orders of magnitude in length scale.
Shear strength of chromia across multiple length scales: An LDA + U study
Mosey, Nicholas J. [Department of Mechanical and Aerospace Engineering and Program in Applied and Computational Mathematics, Princeton University, Princeton, NJ 08544-5263 (United States); Carter, Emily A., E-mail: eac@princeton.edu [Department of Mechanical and Aerospace Engineering and Program in Applied and Computational Mathematics, Princeton University, Princeton, NJ 08544-5263 (United States)
2009-06-15
A method for predicting the shear strength of materials over multiple length scales is developed and tested. The method is based on renormalizing the energies and shear displacements obtained through electronic structure calculations of nanoscale models of the material of interest. All material- and size-dependent quantities are incorporated into the renormalization factors, yielding a universal model that can be applied to many materials and length scales. The model is used to predict the shear strength of Cr{sub 2}O{sub 3} along three relevant slip planes and slip directions. The results demonstrate that the shear strengths of the nanoscale systems used in the calculations range from 19.4 to 29.4 GPa. These data are then renormalized to predict the shear strength of a grain that is 10 {mu}m thick, yielding shear strengths ranging from 189 to 342 MPa. The large decrease in the shear strength with increasing grain size is consistent with the behavior of many materials. The ability to capture this change using electronic structure calculations that do not require experimental input may be useful in developing cohesive laws of novel materials for use in large-scale mechanical engineering simulations of materials failure.
Physics on smallest scales. An introduction to minimal length phenomenology
Sprenger, Martin [Deutsches Elektronen-Synchrotron (DESY), Hamburg (Germany); Goethe Univ., Frankfurt am Main (Germany). Inst. for Theoretical Physics and Frankfurt Institute for Advanced Studies; Nicolini, Piero; Bleicher, Marcus [Goethe Univ., Frankfurt am Main (Germany). Inst. for Theoretical Physics and Frankfurt Institute for Advanced Studies
2012-02-15
Many modern theories which try to unite gravity with the Standard Model of particle physics, as e.g. string theory, propose two key modifications to the commonly known physical theories: - the existence of additional space dimensions - the existence of a minimal length distance or maximal resolution. While extra dimensions have received a wide coverage in publications over the last ten years (especially due to the prediction of micro black hole production at the LHC), the phenomenology of models with a minimal length is still less investigated. In a summer study project for bachelor students in 2010 we have explored some phenomenological implications of the potential existence of a minimal length. In this paper we review the idea and formalism of a quantum gravity induced minimal length in the generalised uncertainty principle framework as well as in the coherent state approach to non- commutative geometry. These approaches are effective models which can make model-independent predictions for experiments and are ideally suited for phenomenological studies. Pedagogical examples are provided to grasp the effects of a quantum gravity induced minimal length. (orig.)
Strength-length scaling of elementary hemp fibers
Poriķe, E.; Andersons, J.
2013-03-01
The application of hemp fibers as a reinforcement of composite materials necessitates the characterization of fiber strength scatter and the effect of fiber length on its strength. With this aim, elementary hemp fibers were tested in tension at two different gage lengths. Due to the similar morphology of hemp and flax fibers, the probabilistic strength models derived and verified for the latter were applied to the former. The fiber strength was found to agree with the modified Weibull distribution. The modeling approaches developed for describing the variability of the strength and failure strain of elementary flax fibers are shown to be also applicable to hemp fibers.
Determination of length scale effects in nonlocal media
Simone, A; Iacono, C; Sluys, LJ; Yao, ZH; Yuan, MW; Zhong, WX
2004-01-01
A combined continuous-discontinuous framework for failure is presented. Continuous failure is described with a gradient enhanced damage model and discontinuous failure is introduced by adding discontinuities to finite elements through a node-based enhancement. The continuous model contains a length
Zavadil, Kevin Robert; Wall, Frederick Douglas
2004-03-01
A key factor in our ability to produce and predict the stability of metal-based macro- to nano-scale structures and devices is a fundamental understanding of the localized nature of corrosion. Corrosion processes where physical dimensions become critical in the degradation process include localized corrosion initiation in passivated metals, microgalvanic interactions in metal alloys, and localized corrosion in structurally complex materials like nanocrystalline metal films under atmospheric and inundated conditions. This project focuses on two areas of corrosion science where a fundamental understanding of processes occurring at critical dimensions is not currently available. Sandia will study the critical length scales necessary for passive film breakdown in the inundated aluminum (Al) system and the chemical processes and transport in ultra-thin water films relevant to the atmospheric corrosion of nanocrystalline tungsten (W) films. Techniques are required that provide spatial information without significantly perturbing or masking the underlying relationships. Al passive film breakdown is governed by the relationship between area of the film sampled and its defect structure. We will combine low current measurements with microelectrodes to study the size scale required to observe a single initiation event and record electrochemical breakdown events. The resulting quantitative measure of stability will be correlated with metal grain size, secondary phase size and distribution to understand which metal properties control stability at the macro- and nano-scale. Mechanisms of atmospheric corrosion on W are dependent on the physical dimensions and continuity of adsorbed water layers as well as the chemical reactions that take place in this layer. We will combine electrochemical and scanning probe microscopic techniques to monitor the chemistry and resulting material transport in these thin surface layers. A description of the length scales responsible for driving the
Length scales in glass-forming liquids and related systems: a review
Karmakar, Smarajit; Dasgupta, Chandan; Sastry, Srikanth
2016-01-01
The central problem in the study of glass-forming liquids and other glassy systems is the understanding of the complex structural relaxation and rapid growth of relaxation times seen on approaching the glass transition. A central conceptual question is whether one can identify one or more growing length scale(s) associated with this behavior. Given the diversity of molecular glass-formers and a vast body of experimental, computational and theoretical work addressing glassy behavior, a number of ideas and observations pertaining to growing length scales have been presented over the past few decades, but there is as yet no consensus view on this question. In this review, we will summarize the salient results and the state of our understanding of length scales associated with dynamical slow down. After a review of slow dynamics and the glass transition, pertinent theories of the glass transition will be summarized and a survey of ideas relating to length scales in glassy systems will be presented. A number of studies have focused on the emergence of preferred packing arrangements and discussed their role in glassy dynamics. More recently, a central object of attention has been the study of spatially correlated, heterogeneous dynamics and the associated length scale, studied in computer simulations and theoretical analysis such as inhomogeneous mode coupling theory. A number of static length scales have been proposed and studied recently, such as the mosaic length scale discussed in the random first-order transition theory and the related point-to-set correlation length. We will discuss these, elaborating on key results, along with a critical appraisal of the state of the art. Finally we will discuss length scales in driven soft matter, granular fluids and amorphous solids, and give a brief description of length scales in aging systems. Possible relations of these length scales with those in glass-forming liquids will be discussed.
Minimum Pay Scale and Career Length in the NBA
Johnny Ducking; Peter A. Groothuis; James Richard Hill
2012-01-01
We use data from the National Basketball Association (NBA) to analyze the impact of minimum salaries on an employee’s career length. The NBA has a salary structure in which the minimum salary a player can receive increases with the player’s years of experience. Salary schedules similar to the NBA’s exist in public education, federal government agencies, the Episcopalian church, and unionized industries. Even though the magnitude of the salaries in the NBA differs from other industries, this s...
Filter length scale for continuum modeling of subgrid physics
Simeonov, Julian; Calantoni, Joseph
2014-11-01
Modeling the wide range of scales of geophysical processes with direct numerical simulations (DNS) is currently not feasible. It is therefore typical to explicitly resolve only the large energy-containing scales and to parameterize the unresolved small scales. One approach to separate the scales is by means of spatial filters and here we discuss practical considerations regarding the choice of a volume averaging scale L. We use a macroscopically homogeneous scalar field and quantify the smoothness of the filtered field using a noise metric, ν, defined by the standard deviation of the filtered field normalized by the domain-averaged value of the field. For illustration, we consider the continuum modeling of the particle phase in discrete element method (DEM) simulations and the salt fingers in DNS of double-diffusive convection. We find that ν2 follows an inverse power law dependence on L with an exponent and coefficients proportional to the domain-averaged field value. The empirical power law relation can aid in the development of continuum models from fully resolved simulations while also providing uncertainty estimates of the modeled continuum fields.
SQUID magnetometry from nanometer to centimeter length scales
Hatridge, Michael J. [Univ. of California, Berkeley, CA (United States)
2010-06-01
The development of Superconducting QUantum Interference Device (SQUID)-based magnetometer for two applications, in vivo prepolarized, ultra-low field MRI of humans and dispersive readout of SQUIDs for micro- and nano-scale magnetometery, are the focus of this thesis.
Length scale of a chaotic element in Rayleigh-Bénard convection.
Karimi, A; Paul, M R
2012-12-01
We describe an approach to quantify the length scale of a chaotic element of a Rayleigh-Bénard convection layer exhibiting spatiotemporal chaos. The length scale of a chaotic element is determined by simultaneously evolving the dynamics of two convection layers with a unidirectional coupling that involves only the time-varying values of the fluid velocity and temperature on the lateral boundaries of the domain. In our results we numerically simulate the full Boussinesq equations for the precise conditions of experiment. By varying the size of the boundary used for the coupling we identify a length scale that describes the size of a chaotic element. The length scale of the chaotic element is of the same order of magnitude, and exhibits similar trends, as the natural chaotic length scale that is based upon the fractal dimension.
The Relevant Length of Customer Event History for Churn Prediction: How long is long enough?
M. BALLINGS; D. VAN DEN POEL
2012-01-01
The key question of this study is: How long should the length of customer event history be for customer churn prediction? While most studies in predictive churn modeling aim to improve models by data augmentation or algorithm improvement, this study focuses on a another dimension: time window optimization with respect to predictive performance. This paper first presents a formalization of the time window selection strategy, along with a literature review. Next, using logistic regression, clas...
Determination of Longitudinal Electron Bunch Lengths on Picosecond Time Scales
Martínez, C; Calviño, F
1999-01-01
At CERN (European Laboratory for Particle Physics) the CLIC (Compact Linear Collider) study is pursuing the design of an electron-positron high-energy linear collider using an innovative concept for the RF (Radio Frequency) power production, the socalled two-beam acceleration scheme. In order to keep the length of the collider in a reasonable range while being able of accelerating electrons and positrons up to 5 TeV, the normal-conducting accelerating structures should operate at very high frequency (in this case 30 GHz). The RF power necessary to feed the accelerating cavities is provided by a second electron beam, the drive beam, running parallel to the main beam. The CLIC Test Facility (CTF) was build with the main aim of studying and demonstrating the feasibility of the two beam acceleration scheme and technology. It is composed of two beams, the drive beam that will generate the 30 GHz RF power and the main beam which will be accelerated by this power. In order to have a good efficiency for the power gen...
Implementing structural slow light on short length scales: the photonic speed-bump
Faggiani, Remi; Hostein, Richard; Lalanne, Philippe
2016-01-01
One-dimensional (1D) infinite periodic systems exhibit vanishing group velocity and diverging density of states (DOS) near band edges. However, in practice, systems have finite sizes and inevitably this prompts the question of whether helpful physical quantities related to infinite systems, such as the group velocity that is deduced from the band structure, remain relevant in finite systems. For instance, one may wonder how the DOS divergence can be approached with finite systems. Intuitively, one may expect that the implementation of larger and larger DOS, or equivalently smaller and smaller group velocities, would critically increase the system length. Based on general 1D-wave-physics arguments, we demonstrate that the large slow-light DOS enhancement of periodic systems can be observed with very short systems, whose lengths scale with the logarithm of the inverse of the group velocities. The understanding obtained for 1D systems leads us to propose a novel sort of microstructure to enhance light-matter int...
An updated length-scale formulation for turbulent mixing in clear and cloudy boundary layers
Lenderink, G.; Holtslag, A. A. M.
2004-10-01
A new mixing-length scale is presented for turbulence-closure schemes, with special emphasis on neutral-to-convective conditions in clear and cloudy boundary layers. The length scale is intended for a prognostic turbulent-kinetic-energy closure. It is argued that present-day length-scale formulations may easily fail in one of two limiting situations. Schemes based on a local stability measure (e.g.the Richardson number) display unrealistic behaviour and instabilities in the convective limit. This strongly limits the representation of mixing in cloudy boundary layers. On the other hand, it is shown that non-local parcel methods may misrepresent mixing near the surface. The new length-scale formulation combines local and non-local stability in a new way; it uses vertical integrals over the stability (the Richardson number) in a simple 'parcel' framework. The length scale matches with surface-layer similarity for near-neutral conditions and displays a realistic convective limit. The use of the length-scale formulation can be extended easily to cloudy boundary layers. The scheme is numerically stable and computationally cheap. The behaviour of the length scale is evaluated in a single-column model (SCM) and in a high-resolution limited-area model (LAM). The SCM shows good behaviour in three cases with and without boundary-layer clouds. The prediction of the near-surface wind and temperature in the LAM compares favourably with tower measurements at Cabauw (the Netherlands).
Nonsymmorphic Phononic Metamaterials: shaping waves over multiple length scales
Koh, Cheongyang; Thomas, Edwin
2012-02-01
The vector nature of the phonon makes rational design of phononic metamaterials challenging, despite potential in unique wave propagation behavior, such as negative refraction and hyper-lensing. While most designs to date focus on the ``meta-atom'' (building block) design, their ``spatial arrangement'' (non-locality) is equally instrumental in dispersion engineering. Here, we present a generalized design framework (DF) for PMM design, utilizing both ``global'' and ``local'' symmetry concepts. We demonstrate, utilizing specific properties of nonsymmorphic plane groups, PMMs possessing i) a low-frequency in-plane complete spectral gap (ICSG) of 102% (CSG of 88%), ii) a set of polychromatic ICSGs totaling over 100% in normalized gap size. Within the same DF, we further integrate broken symmetry states (BSS) (edge states, waveguides, etc) with designed polarization, (de)localization and group velocities. In particular, we demonstrate how these BSS may be utilized to elucidate signatures of complex polarization fields through phonon-structure interactions, leading to interesting applications in elastic-wave imaging, as well as information retrieval by probing polarization states of scattering bodies over multiple scales.
Non-perturbative gravity at different length scales
Folkerts, Sarah
2013-12-18
In this thesis, we investigate different aspects of gravity as an effective field theory. Building on the arguments of self-completeness of Einstein gravity, we argue that any sensible theory, which does not propagate negative-norm states and reduces to General Relativity in the low energy limit is self-complete. Due to black hole formation in high energy scattering experiments, distances smaller than the Planck scale are shielded from any accessibility. Degrees of freedom with masses larger than the Planck mass are mapped to large classical black holes which are described by the already existing infrared theory. Since high energy (UV) modifications of gravity which are ghost-free can only produce stronger gravitational interactions than Einstein gravity, the black hole shielding is even more efficient in such theories. In this light, we argue that conventional attempts of a Wilsonian UV completion are severely constrained. Furthermore, we investigate the quantum picture for black holes which emerges in the low energy description put forward by Dvali and Gomez in which black holes are described as Bose-Einstein condensates of many weakly coupled gravitons. Specifically, we investigate a non-relativistic toy model which mimics certain aspects of the graviton condensate picture. This toy model describes the collapse of a condensate of attractive bosons which emits particles due to incoherent scattering. We show that it is possible that the evolution of the condensate follows the critical point which is accompanied by the appearance of a light mode. Another aspect of gravitational interactions concerns the question whether quantum gravity breaks global symmetries. Arguments relying on the no hair theorem and wormhole solutions suggest that global symmetries can be violated. In this thesis, we parametrize such effects in terms of an effective field theory description of three-form fields. We investigate the possible implications for the axion solution of the strong CP
Plasma scale-length effects on electron energy spectra in high-irradiance laser plasmas
Culfa, O.; Tallents, G. J.; Rossall, A. K.; Wagenaars, E.; Ridgers, C. P.; Murphy, C. D.; Dance, R. J.; Gray, R. J.; McKenna, P.; Brown, C. D. R.; James, S. F.; Hoarty, D. J.; Booth, N.; Robinson, A. P. L.; Lancaster, K. L.; Pikuz, S. A.; Faenov, A. Ya.; Kampfer, T.; Schulze, K. S.; Uschmann, I.; Woolsey, N. C.
2016-04-01
An analysis of an electron spectrometer used to characterize fast electrons generated by ultraintense (1020W cm-2 ) laser interaction with a preformed plasma of scale length measured by shadowgraphy is presented. The effects of fringing magnetic fields on the electron spectral measurements and the accuracy of density scale-length measurements are evaluated. 2D EPOCH PIC code simulations are found to be in agreement with measurements of the electron energy spectra showing that laser filamentation in plasma preformed by a prepulse is important with longer plasma scale lengths (>8 μ m ).
Cable dynamics applied to long-length scale mechanics of DNA
Goyal, Sachin; Lillian, Todd; Noel C Perkins; Meyhofer, Edgar
2007-01-01
This paper introduces the use of cable dynamics models as a means to explore the mechanics of DNA on long-length scales. It is on these length scales that DNA forms twisted and curved three-dimensional shapes known as supercoils and loops. These long-length scale DNA structures have a pronounced influence on the functions of this molecule within the cell including the packing of DNA in the cell nucleus, transcription, replication and gene repair. We provide a short background to the mechanics...
Long-time data storage: relevant time scales
Elwenspoek, Miko C.
2011-01-01
Dynamic processes relevant for long-time storage of information about human kind are discussed, ranging from biological and geological processes to the lifecycle of stars and the expansion of the universe. Major results are that life will end ultimately and the remaining time that the earth is habit
Magnetized and collimated millimeter scale plasma jets with astrophysical relevance
Brady, Parrish C.; Quevedo, Hernan J. [Texas Center for High Intensity Laser Science, University of Texas at Austin, Austin, Texas 78712 (United States); Valanju, Prashant M. [Institute for Fusion Studies, University of Texas at Austin, Austin, Texas 78712-1060 (United States); Bengtson, Roger D.; Ditmire, Todd [Department of Physics, University of Texas at Austin, Austin, Texas 78712 (United States)
2012-01-15
Magnetized collimated plasma jets are created in the laboratory to extend our understanding of plasma jet acceleration and collimation mechanisms with particular connection to astrophysical jets. In this study, plasma collimated jets are formed from supersonic unmagnetized flows, mimicking a stellar wind, subject to currents and magnetohydrodynamic forces. It is found that an external poloidal magnetic field, like the ones found anchored to accretion disks, is essential to stabilize the jets against current-driven instabilities. The maximum jet length before instabilities develop is proportional to the field strength and the length threshold agrees well with Kruskal-Shafranov theory. The plasma evolution is modeled qualitatively using MHD theory of current-carrying flux tubes showing that jet acceleration and collimation arise as a result of electromagnetic forces.
Sohrab, Siavash
Thermodynamic equilibrium between matter and radiation leads to de Broglie wavelength λdβ = h /mβvrβ and frequency νdβ = k /mβvrβ of matter waves and stochastic definitions of Planck h =hk =mk c and Boltzmann k =kk =mk c constants, λrkνrk = c , that respectively relate to spatial (λ) and temporal (ν) aspects of vacuum fluctuations. Photon massmk =√{ hk /c3 } , amu =√{ hkc } = 1 /No , and universal gas constant Ro =No k =√{ k / hc } result in internal Uk = Nhνrk = Nmkc2 = 3 Nmkvmpk2 = 3 NkT and potential pV = uN\\vcirc / 3 = N\\ucirc / 3 = NkT energy of photon gas in Casimir vacuum such that H = TS = 4 NkT . Therefore, Kelvin absolute thermodynamic temperature scale [degree K] is identified as length scale [meter] and related to most probable wavelength and de Broglie thermal wavelength as Tβ =λmpβ =λdβ / 3 . Parallel to Wien displacement law obtained from Planck distribution, the displacement law λwS T =c2 /√{ 3} is obtained from Maxwell -Boltzmann distribution of speed of ``photon clusters''. The propagation speeds of sound waves in ideal gas versus light waves in photon gas are described in terms of vrβ in harmony with perceptions of Huygens. Newton formula for speed of long waves in canals √{ p / ρ } is modified to √{ gh } =√{ γp / ρ } in accordance with adiabatic theory of Laplace.
Szazdi, Laszlo; Abranyi, Agnes; Pukansky Jr, Bela; Vancso, G. Julius; Pukanszky, Bela
2006-01-01
The structure and rheological properties of a large number of layered silicate poly(propylene) nanocomposites were studied with widely varying compositions. Morphology characterization at different length scales was achieved by SEM, TEM, and XRD. Rheological measurements supplied additional informat
Drozdzik, Marek; Gröer, Christian; Penski, Jette; Lapczuk, Joanna; Ostrowski, Marek; Lai, Yurong; Prasad, Bhagwat; Unadkat, Jashvant D; Siegmund, Werner; Oswald, Stefan
2014-10-01
Intestinal transporters are crucial determinants in the oral absorption of many drugs. We therefore studied the mRNA expression (N = 33) and absolute protein content (N = 10) of clinically relevant transporters in healthy epithelium of the duodenum, the proximal and distal jejunum and ileum, and the ascending, transversal, descending, and sigmoidal colon of six organ donors (24-54 years). In the small intestine, the abundance of nearly all studied proteins ranged between 0.2 and 1.6 pmol/mg with the exception of those of OCT3 (intestinal segment. ABCB1, ABCG2, PEPT1, and ASBT were significantly more abundant in jejunum and ileum than in colon. In contrast to this, the level of expression of ABCC2, ABCC3, and OCT3 was found to be highest in colon. Site-dependent differences in the levels of gene and protein expression were observed for ABCB1 and ASBT. Significant correlations between mRNA and protein levels have been found for ABCG2, ASBT, OCT3, and PEPT1 in the small intestine. Our data provide further physiological pieces of the puzzle required to predict intestinal drug absorption in humans.
Desert bird associations with broad-scale boundary length: Applications in avian conservation
Gutzwiller, K.J.; Barrow, W.C.
2008-01-01
1. Current understanding regarding the effects of boundaries on bird communities has originated largely from studies of forest-non-forest boundaries in mesic systems. To assess whether broad-scale boundary length can affect bird community structure in deserts, and to identify patterns and predictors of species' associations useful in avian conservation, we studied relations between birds and boundary-length variables in Chihuahuan Desert landscapes. Operationally, a boundary was the border between two adjoining land covers, and broad-scale boundary length was the total length of such borders in a large area. 2. Within 2-km radius areas, we measured six boundary-length variables. We analysed bird-boundary relations for 26 species, tested for assemblage-level patterns in species' associations with boundary-length variables, and assessed whether body size, dispersal ability and cowbird-host status were correlates of these associations. 3. The abundances or occurrences of a significant majority of species were associated with boundary-length variables, and similar numbers of species were related positively and negatively to boundary-length variables. 4. Disproportionately small numbers of species were correlated with total boundary length, land-cover boundary length and shrubland-grassland boundary length (variables responsible for large proportions of boundary length). Disproportionately large numbers of species were correlated with roadside boundary length and riparian vegetation-grassland boundary length (variables responsible for small proportions of boundary length). Roadside boundary length was associated (positively and negatively) with the most species. 5. Species' associations with boundary-length variables were not correlated with body size, dispersal ability or cowbird-host status. 6. Synthesis and applications. For the species we studied, conservationists can use the regressions we report as working models to anticipate influences of boundary-length changes
Length Scaling of Shear Zones at the Frictional-Viscous Transition (FVT)
Schrank, C. E.; Handy, M. R.; Fusseis, F.
2005-12-01
We present a new method for determining the characteristic length scales of strain localization in crustal scale shear zones. This entails determining two parameters that describe the degree of strain heterogeneity in natural shear zones: (1) the strain localization factor, LfRA, defined as the ratio of the shear zone area to a chosen reference area, ARA, and (2) the relative localization intensity, Iloc, a function of the ratio of the mean shear strain to the maximum shear strain measured in a transect of the shear zone. ARA is a geometric homogenization scale determined from autocorrelation functions (ACF) of 2-D images (thin sections, foliation maps and aerial photographs) of shear zone networks on different scales that formed during a single deformational event. When applied to shear zones from a well exposed segment of the frictional-to-viscous transition (FVT) in NE Spain, we found that maxima in LfRA on the mm, cm, m and km scales coincided with the length scales of existing mineralogical and lithological heterogeneities. On any of these characteristic length scales, Iloc increased both along and across the length of the shear zones, suggesting that the shear zones weakening as a function of time and strain. This is consistent with structural evidence for progressive weakening of the crust on the characteristic length scales of strain heterogeneity.
Ichitaro Yamazaki; Zhaojun Bai; Wenbin Chen; Richard Scalettar
2009-01-01
We study preconditioning techniques used in conjunction with the conjugate gradient method for solving multi-length-scale symmetric positive definite linear systems originating from the quantum Monte Carlo simulation of electron interaction of correlated materials. Existing preconditioning techniques are not designed to be adaptive to varying numerical properties of the multi-length-scale systems. In this paper, we propose a hybrid incomplete Cholesky (HIC) preconditioner and demonstrate its adaptivity to the multi-length-scale systems. In addition, we propose an extension of the compressed sparse column with row access (CSCR) sparse matrix storage format to efficiently accommodate the data access pattern to compute the HIC preconditioner. We show that for moderately correlated materials, the HIC preconditioner achieves the optimal linear scaling of the simulation. The development of a linear-scaling preconditioner for strongly correlated materials remains an open topic.
Size effects and internal length scales in the elasticity of random fiber networks
Picu, Catalin; Berkache, Kamel; Shahsavari, Ali; Ganghoffer, Jean-Francois
Random fiber networks are the structural element of many biological and man-made materials, including connective tissue, various consumer products and packaging materials. In all cases of practical interest the scale at which the material is used and the scale of the fiber diameter or the mean segment length of the network are separated by several orders of magnitude. This precludes solving boundary value problems defined on the scale of the application while resolving every fiber in the system, and mandates the development of continuum equivalent models. To this end, we study the intrinsic geometric and mechanical length scales of the network and the size effect associated with them. We consider both Cauchy and micropolar continuum models and calibrate them based on the discrete network behavior. We develop a method to predict the characteristic length scales of the problem and the minimum size of a representative element of the network based on network structural parameters and on fiber properties.
Relevant Spatial Scales of Chemical Variation in Aplysina aerophoba
Oriol Sacristan-Soriano
2011-11-01
Full Text Available Understanding the scale at which natural products vary the most is critical because it sheds light on the type of factors that regulate their production. The sponge Aplysina aerophoba is a common Mediterranean sponge inhabiting shallow waters in the Mediterranean and its area of influence in Atlantic Ocean. This species contains large concentrations of brominated alkaloids (BAs that play a number of ecological roles in nature. Our research investigates the ecological variation in BAs of A. aerophoba from a scale of hundred of meters to thousand kilometers. We used a nested design to sample sponges from two geographically distinct regions (Canary Islands and Mediterranean, over 2500 km, with two zones within each region (less than 50 km, two locations within each zone (less than 5 km, and two sites within each location (less than 500 m. We used high-performance liquid chromatography to quantify multiple BAs and a spectrophotometer to quantify chlorophyll a (Chl a. Our results show a striking degree of variation in both natural products and Chl a content. Significant variation in Chl a content occurred at the largest and smallest geographic scales. The variation patterns of BAs also occurred at the largest and smallest scales, but varied depending on which BA was analyzed. Concentrations of Chl a and isofistularin-3 were negatively correlated, suggesting that symbionts may impact the concentration of some of these compounds. Our results underline the complex control of the production of secondary metabolites, with factors acting at both small and large geographic scales affecting the production of multiple secondary metabolites.
Empirical scaling of the length of the longest increasing subsequences of random walks
Mendonça, J. Ricardo G.
2017-02-01
We provide Monte Carlo estimates of the scaling of the length L n of the longest increasing subsequences of n-step random walks for several different distributions of step lengths, short and heavy-tailed. Our simulations indicate that, barring possible logarithmic corrections, {{L}n}∼ {{n}θ} with the leading scaling exponent 0.60≲ θ ≲ 0.69 for the heavy-tailed distributions of step lengths examined, with values increasing as the distribution becomes more heavy-tailed, and θ ≃ 0.57 for distributions of finite variance, irrespective of the particular distribution. The results are consistent with existing rigorous bounds for θ, although in a somewhat surprising manner. For random walks with step lengths of finite variance, we conjecture that the correct asymptotic behavior of L n is given by \\sqrt{n}\\ln n , and also propose the form for the subleading asymptotics. The distribution of L n was found to follow a simple scaling form with scaling functions that vary with θ. Accordingly, when the step lengths are of finite variance they seem to be universal. The nature of this scaling remains unclear, since we lack a working model, microscopic or hydrodynamic, for the behavior of the length of the longest increasing subsequences of random walks.
Evaluating the accuracy of finite element models at reduced length scales
Kemp, Connor
Finite element models are used frequently in both engineering and scientific research. While they can provide useful information as to the performance of materials, as length scales are decreased more sophisticated model descriptions are required. It is also important to develop methods by which existing models may be verified against experimental findings. The present study evaluates the ability of various finite element models to predict materials behaviour at length scales ranging from several microns to tens of nanometers. Considering this motivation, this thesis is provided in manuscript form with the bulk of material coming from two case studies. Following an overview of relevant literature in Chapter 2, Chapter 3 considers the nucleation of delta-zirconium hydrides in a Zircaloy-2 matrix. Zirconium hydrides are an important topic in the nuclear industry as they form a brittle phase which leads to delayed hydride cracking during reactor start-up and shut-down. Several FE models are used to compare present results with literature findings and illustrate the weaknesses of standard FE approaches. It is shown that standard continuum techniques do not sufficiently capture the interfacial effects of an inclusion-matrix system. By using nano-scale material descriptions, nucleation lattice strains are obtained which are in good agreement with previous experimental studies. The motivation for Chapter 4 stems from a recognized need to develop a method for modeling corrosion behaviour of materials. Corrosion is also an issue for reactor design and an ability to predict failure points is needed. Finite element models could be used for this purpose, provided model accuracy is verified first. In Chapter 4 a technique is developed which facilitates the extraction of sub-micron resolution strain data from correlation images obtained during in-situ tensile deformation. By comparing image correlation results with a crystal plasticity finite element code it is found that good
Long-Time Data Storage: Relevant Time Scales
Miko C. Elwenspoek
2011-02-01
Full Text Available Dynamic processes relevant for long-time storage of information about human kind are discussed, ranging from biological and geological processes to the lifecycle of stars and the expansion of the universe. Major results are that life will end ultimately and the remaining time that the earth is habitable for complex life is about half a billion years. A system retrieved within the next million years will be read by beings very closely related to Homo sapiens. During this time the surface of the earth will change making it risky to place a small number of large memory systems on earth; the option to place it on the moon might be more favorable. For much longer timescales both options do not seem feasible because of geological processes on the earth and the flux of small meteorites to the moon.
Low frequency energy scavenging using sub-wave length scale acousto-elastic metamaterial
Riaz U. Ahmed
2014-11-01
Full Text Available This letter presents the possibility of energy scavenging (ES utilizing the physics of acousto-elastic metamaterial (AEMM at low frequencies (<∼3KHz. It is proposed to use the AEMM in a dual mode (Acoustic Filter and Energy Harvester, simultaneously. AEMM’s are typically reported for filtering acoustic waves by trapping or guiding the acoustic energy, whereas this letter shows that the dynamic energy trapped inside the soft constituent (matrix of metamaterials can be significantly harvested by strategically embedding piezoelectric wafers in the matrix. With unit cell AEMM model, we experimentally asserted that at lower acoustic frequencies (< ∼3 KHz, maximum power in the micro Watts (∼35µW range can be generated, whereas, recently reported phononic crystal based metamaterials harvested only nano Watt (∼30nW power against 10KΩ resistive load. Efficient energy scavengers at low acoustic frequencies are almost absent due to large required size relevant to the acoustic wavelength. Here we report sub wave length scale energy scavengers utilizing the coupled physics of local, structural and matrix resonances. Upon validation of the argument through analytical, numerical and experimental studies, a multi-frequency energy scavenger (ES with multi-cell model is designed with varying geometrical properties capable of scavenging energy (power output from ∼10µW – ∼90µW between 0.2 KHz and 1.5 KHz acoustic frequencies.
DNA flexibility on short length scales probed by atomic force microscopy.
Mazur, Alexey K; Maaloum, Mounir
2014-02-14
Unusually high bending flexibility has been recently reported for DNA on short length scales. We use atomic force microscopy (AFM) in solution to obtain a direct estimate of DNA bending statistics for scales down to one helical turn. It appears that DNA behaves as a Gaussian chain and is well described by the wormlike chain model at length scales beyond 3 helical turns (10.5 nm). Below this threshold, the AFM data exhibit growing noise because of experimental limitations. This noise may hide small deviations from the Gaussian behavior, but they can hardly be significant.
Brosten, Tyler R; Codd, Sarah L; Maier, Robert S; Seymour, Joseph D
2009-11-20
Nuclear magnetic resonance measurements of scale dependent dynamics in a random solid open-cell foam reveal a characteristic length scale for transport processes in this novel type of porous medium. These measurements and lattice Boltzmann simulations for a model foam structure indicate dynamical behavior analogous to lower porosity consolidated granular porous media, despite extremely high porosity in solid cellular foams. Scaling by the measured characteristic length collapses data for different foam structures as well as consolidated granular media. The nonequilibrium statistical mechanics theory of preasymptotic dispersion, developed for hierarchical porous media, is shown to model the hydrodynamic dispersive transport in a foam structure.
Magnetically stabilized bed dust filters-Analysis through variable length scale approach
Jordan Hristov
2007-01-01
Magnetically stabilized beds are packed beds subjected to fluid-driven deformation and controlled by magnetically induced interparticle forces.This paper deals with magnetically stabilized beds as deformable porous media and describes their application in dust filtration. The Richardson-Zaki scaling law, U/Ut = εn describes the field controlled bed expansion via the exponent n, that yields a porosity-dependent flow length scale dc =dpεn.The paper addresses two issues: (i) deformation characteristics by assuming homogeneous bed expansion and a definition of bed variable flow length scale; (ii) dust filtration characteristics such as filter coefficient, specific deposit and filtration efficiency expressed in terms of the variable flow length scale and illustrated by experimental data.
Large-scale length that could determine the mean rate of energy dissipation in turbulence
Mouri, H; Kawashima, Y; Hashimoto, K
2012-01-01
The mean rate of energy dissipation in turbulence is traditionally assumed to scale with parameters of the energy-containing large scales, i.e., the root-mean-square fluctuation of the longitudinal velocity u and its correlation length L(u). However, the resultant scaling coefficient C(u) is known to depend on the large-scale configuration of the flow. We define the correlation length L(u2) of the local energy u2, study the scaling coefficient C(u2) with experimental data of several flows, and find a possibility that C(u2) does not depend on the flow configuration. Not L(u) but rather L(u2) could scale with the typical size of the energy-containing eddies, so that L(u2) determines the mean rate at which the energy is transferred from those eddies to the smaller eddies and is eventually dissipated into heat.
Chakraborty, S; Arora, A K; Sivasubramanian, V; Krishna, P S R; Krishnan, R Venkata
2012-12-19
Processes occurring at macroscopic and microscopic length scales across the glass transition (T(g)) in lead-tellurite glass (PbO)(x)(TeO(2))(1-x) (x = 0.1-0.3) are investigated using Brillouin and Raman spectroscopy, respectively. For all the samples, the temperature dependence of the longitudinal acoustic (LA) mode is found to exhibit a universal scaling below T(g) and a rapid softening above T(g). The lower value of elastic modulus at a higher concentration of network modifier PbO, estimated from Brillouin data, arises due to loss of network rigidity. From quantitative analysis of the reduced Raman spectra, several modes are found to exhibit anomalous changes across T(g). Instead of the expected anharmonic behaviour, several modes exhibit hardening, suggesting stiffening of the stretching force constants with temperature, the effect being more pronounced in glasses with higher x. In addition, incorporation of PbO in the glass is also found to narrow down the bond-length distribution, as evident from the sharpening of the Raman bands. The stiffening of the force constants of molecular units at a microscopic length scale and the decrease of elastic constant attributed to loss of network rigidity on a macroscopic length scale appear to be opposite. These different behaviours at two length scales are understood on the basis of a microscopic model involving TeO(n) and PbO units in the structure.
Integral Length and Time Scales of Velocity, Heat and Mass At and Near a Turbulent Free Surface
Curtis, G. M.; Zappa, C. J.; Variano, E. A.
2010-12-01
variation in integral length scales enabled the effective identification of periods of heavy turbulent mixing at the surface and revealed the localized nature of such events. Analogous to the integral length scale, the integral time scale analysis revealed the characteristic duration of turbulent events at the surface. Covariance and cospectra quantify the time and length scales that are most relevant to fluxes. The measurements presented here will increase our understanding of turbulent transport across the air-sea interface.
Laser Acoustic Microstructure Analysis at the Micron and Nanometer Length Scale
Telschow, K.L.; Hurley, D.H.
2002-05-15
Laser acoustic approaches to investigating the interaction of elastic waves with microstructure in materials is presented that probe both the micron and nanometer length scales. At the micron length scale, a full-field imaging approach is described that provides quantitative measurement of amplitude and phase of the out-of-plane acoustical motion at GHz frequencies. Specific lateral acoustic modes can be identified in addition to the primary thickness mode with spatial resolution sufficient to image wavelengths as small as 4.5 microns.
Laser Acoustic Microstructure Analysis at the Micron and Nanometer Length Scale
Telschow, Kenneth Louis; Hurley, David Howard
2002-05-01
Laser acoustic approaches to investigating the interaction of elastic waves with microstructure in materials is presented that probe both the micron and nanometer length scales. At the micron length scale, a full-field imaging approach is described that provides quantitative measurement of amplitude and phase of the out-of-plane acoustical motion at GHz frequencies. Specific lateral acoustic modes can be identified in addition to the primary thickness mode with spatial resolution sufficient to image wavelengths as small as 4.5 microns.
Observing Evolution in the Supergranular Length Scale During Periods of Low Solar Activity
McIntosh, Scott W; Hoch, Rachel A; Rast, Mark P; Ulrich, Roger K
2011-01-01
We present the initial results of an observational study into the variation of the dominant length-scale of quiet solar emission: supergranulation. This length-scale reflects the radiative energy in the plasma of the upper solar chromosphere and transition region at the magnetic network boundaries forming as a result of the relentless interaction of magnetic fields and convective motions of the Sun's interior. We demonstrate that a net difference of ~0.5Mm in the supergranular emission length-scale occurs when comparing observations cycle 22/23 and cycle 23/24 minima. This variation in scale is reproduced in the datasets of multiple space- and ground-based instruments and using different diagnostic measures. By means of extension, we consider the variation of the supergranular length-scale over multiple solar minima by analyzing a subset of the Mt Wilson Solar Observatory (MWO) Ca II K image record. The observations and analysis presented provide a tantalizing look at solar activity in the absence of large-sc...
Interplay between multiple length and time scales in complex chemical systems
Biman Bagchi; Charusita Chakravarty
2010-07-01
Processes in complex chemical systems, such as macromolecules, electrolytes, interfaces, micelles and enzymes, can span several orders of magnitude in length and time scales. The length and time scales of processes occurring over this broad time and space window are frequently coupled to give rise to the control necessary to ensure specificity and the uniqueness of the chemical phenomena. A combination of experimental, theoretical and computational techniques that can address a multiplicity of length and time scales is required in order to understand and predict structure and dynamics in such complex systems. This review highlights recent experimental developments that allow one to probe structure and dynamics at increasingly smaller length and time scales. The key theoretical approaches and computational strategies for integrating information across time-scales are discussed. The application of these ideas to understand phenomena in various areas, ranging from materials science to biology, is illustrated in the context of current developments in the areas of liquids and solvation, protein folding and aggregation and phase transitions, nucleation and self-assembly.
Maglio, Sam J; Trope, Yaacov
2011-02-01
Scale can vary by requiring a different number of units to measure the same target. But what are the consequences of using fewer, larger units? We draw on past psychophysical research that shows how using fewer units reduces clutter in measurement, translating to shorter length estimates. Additionally, we propose that larger scale is associated with targets further from a person's immediate experience (i.e., psychologically distant) and higher order mental representation. Evidence from Study 1 indicates that framing a target as further away causes it to be estimated as shorter because people use larger units to measure it compared to when the same target is framed as nearby. Two subsequent studies suggest that direct manipulation of larger (versus smaller) measurement scale produces not only shorter length estimates, but also more distal timing judgments (Study 2) and abstract mental representation (Study 3). Implications for scale and level of mental construal are discussed.
Multiresolution analysis of characteristic length scales with high-resolution topographic data
Sangireddy, Harish; Stark, Colin P.; Passalacqua, Paola
2017-07-01
Characteristic length scales (CLS) define landscape structure and delimit geomorphic processes. Here we use multiresolution analysis (MRA) to estimate such scales from high-resolution topographic data. MRA employs progressive terrain defocusing, via convolution of the terrain data with Gaussian kernels of increasing standard deviation, and calculation at each smoothing resolution of (i) the probability distributions of curvature and topographic index (defined as the ratio of slope to area in log scale) and (ii) characteristic spatial patterns of divergent and convergent topography identified by analyzing the curvature of the terrain. The MRA is first explored using synthetic 1-D and 2-D signals whose CLS are known. It is then validated against a set of MARSSIM (a landscape evolution model) steady state landscapes whose CLS were tuned by varying hillslope diffusivity and simulated noise amplitude. The known CLS match the scales at which the distributions of topographic index and curvature show scaling breaks, indicating that the MRA can identify CLS in landscapes based on the scaling behavior of topographic attributes. Finally, the MRA is deployed to measure the CLS of five natural landscapes using meter resolution digital terrain model data. CLS are inferred from the scaling breaks of the topographic index and curvature distributions and equated with (i) small-scale roughness features and (ii) the hillslope length scale.
What structural length scales can be detected by the spectral variance of a microscope image?
Cherkezyan, Lusik; Subramanian, Hariharan; Backman, Vadim
2014-01-01
A spectroscopic microscope, configured to detect interference spectra of backscattered light in the far zone, quantifies the statistics of refractive-index (RI) distribution via the spectral variance (Σ̃2) of the acquired bright-field image. Its sensitivity to subtle structural changes within weakly scattering, label-free media at subdiffraction scales shows great promise in fields from material science to medical diagnostics. We further investigate the length-scale sensitivity of Σ̃ and reve...
Fabbris, G.; Hücker, M.; Gu, G. D.; Tranquada, J. M.; Haskel, D.
2016-07-01
Some of the most exotic material properties derive from electronic states with short correlation length (~10-500 {\\AA}), suggesting that the local structural symmetry may play a relevant role in their behavior. Here we discuss the combined use of polarized x-ray absorption fine structure and x-ray diffraction at high pressure as a powerful method to tune and probe structural and electronic orders at multiple length scales. Besides addressing some of the technical challenges associated with such experiments, we illustrate this approach with results obtained in the cuprate La$_{1.875}$Ba$_{0.125}$CuO$_4$, in which the response of electronic order to pressure can only be understood by probing the structure at the relevant length scales.
Nano-scaled graphene platelets with a high length-to-width aspect ratio
Zhamu, Aruna; Guo, Jiusheng; Jang, Bor Z.
2010-09-07
This invention provides a nano-scaled graphene platelet (NGP) having a thickness no greater than 100 nm and a length-to-width ratio no less than 3 (preferably greater than 10). The NGP with a high length-to-width ratio can be prepared by using a method comprising (a) intercalating a carbon fiber or graphite fiber with an intercalate to form an intercalated fiber; (b) exfoliating the intercalated fiber to obtain an exfoliated fiber comprising graphene sheets or flakes; and (c) separating the graphene sheets or flakes to obtain nano-scaled graphene platelets. The invention also provides a nanocomposite material comprising an NGP with a high length-to-width ratio. Such a nanocomposite can become electrically conductive with a small weight fraction of NGPs. Conductive composites are particularly useful for shielding of sensitive electronic equipment against electromagnetic interference (EMI) or radio frequency interference (RFI), and for electrostatic charge dissipation.
Infrared length scale and extrapolations for the no-core shell model
Wendt, K A; Papenbrock, T; Sääf, D
2015-01-01
We precisely determine the infrared (IR) length scale of the no-core shell model (NCSM). In the NCSM, the $A$-body Hilbert space is truncated by the total energy, and the IR length can be determined by equating the intrinsic kinetic energy of $A$ nucleons in the NCSM space to that of $A$ nucleons in a $3(A-1)$-dimensional hyper-radial well with a Dirichlet boundary condition for the hyper radius. We demonstrate that this procedure indeed yields a very precise IR length by performing large-scale NCSM calculations for $^{6}$Li. We apply our result and perform accurate IR extrapolations for bound states of $^{4}$He, $^{6}$He, $^{6}$Li, $^{7}$Li. We also attempt to extrapolate NCSM results for $^{10}$B and $^{16}$O with bare interactions from chiral effective field theory over tens of MeV.
Numerical scalings of the decay lengths in the scrape-off layer
Militello, F.; Naulin, V; Nielsen, Anders Henry
2013-01-01
Numerical simulations of L-mode turbulence in the scrape-off layer (SOL) are used to construct power scaling laws for the characteristic decay lengths of the temperature, density and heat flux at the outer mid-plane. Most of the results obtained are in qualitative agreement with the experimental...
Smirnova, YG; ten Brinke, G; Erukhimovich, IY; Smirnova, Yuliya G.; Erukhimovich, Igor Ya.
2006-01-01
The phase behavior of A(fmN)(B(N/2)A(N/2))B(1-f)mN multiblock copolymer melts is studied within the weak segregation theory. The interplay between ordering on different length scales is shown to cause dramatic changes both in the ordered phase symmetry and periodicity upon small variation of the arc
Berg, van den L.; Rosenberg, Y.; Boekel, van M.A.J.S.; Rosenberg, M.; Velde, van de F.
2009-01-01
Mixed biopolymer gels are often used to model semi-solid food products. Understanding of their functional properties requires knowledge about structural elements composing these systems at various length scales. This study has been focused on investigating the structural features of mixed cold-set g
Enhanced Strain in Functional Nanoporous Gold with a Dual Microscopic Length Scale Structure
Detsi, Eric; Punzhin, Sergey; Rao, Jiancun; Onck, Patrick R.; De Hosson, Jeff Th. M.
2012-01-01
We have synthesized nanoporous Au with a dual microscopic length scale by exploiting the crystal structure of the alloy precursor. The synthesized mesoscopic material is characterized by stacked Au layers of submicrometer thickness. In addition, each layer displays nanoporosity through the entire bu
Smirnova, YG; ten Brinke, G; Erukhimovich, IY; Smirnova, Yuliya G.; Erukhimovich, Igor Ya.
2006-01-01
The phase behavior of A(fmN)(B(N/2)A(N/2))B(1-f)mN multiblock copolymer melts is studied within the weak segregation theory. The interplay between ordering on different length scales is shown to cause dramatic changes both in the ordered phase symmetry and periodicity upon small variation of the arc
Berg, van den L.; Rosenberg, Y.; Boekel, van M.A.J.S.; Rosenberg, M.; Velde, van de F.
2009-01-01
Mixed biopolymer gels are often used to model semi-solid food products. Understanding of their functional properties requires knowledge about structural elements composing these systems at various length scales. This study has been focused on investigating the structural features of mixed cold-set g
Roughness controlled superhydrophobicity on single nanometer length scale with metal nanoparticles
ten Brink, Gert H.; Foley, Nolan; Zwaan, Darin; Kooi, Bart J.; Palasantzas, Georgios
2015-01-01
Here we demonstrate high water pinning nanostructures and trapping of water droplets onto surfaces via control of roughness on a single nanometer length-scale generated by deposition of preformed gas phase distinct copper nanoparticles on hydrophilic and hydrophobic surfaces. It was found that the c
Roughness controlled superhydrophobicity on single nanometer length scale with metal nanoparticles
ten Brink, Gert H.; Foley, Nolan; Zwaan, Darin; Kooi, Bart J.; Palasantzas, Georgios
2015-01-01
Here we demonstrate high water pinning nanostructures and trapping of water droplets onto surfaces via control of roughness on a single nanometer length-scale generated by deposition of preformed gas phase distinct copper nanoparticles on hydrophilic and hydrophobic surfaces. It was found that the
Wind direction variations in the natural wind – A new length scale
Johansson, Jens; Christensen, Silas Sverre
2017-01-01
During an observation period of e.g. 10min, the wind direction will differ from its mean direction for short periods of time, and a body of air will pass by from that direction before the direction changes once again. The present paper introduces a new length scale which we have labeled the angul...
Scale and time dependence of serial correlations in word-length time series of written texts
Rodriguez, E.; Aguilar-Cornejo, M.; Femat, R.; Alvarez-Ramirez, J.
2014-11-01
This work considered the quantitative analysis of large written texts. To this end, the text was converted into a time series by taking the sequence of word lengths. The detrended fluctuation analysis (DFA) was used for characterizing long-range serial correlations of the time series. To this end, the DFA was implemented within a rolling window framework for estimating the variations of correlations, quantified in terms of the scaling exponent, strength along the text. Also, a filtering derivative was used to compute the dependence of the scaling exponent relative to the scale. The analysis was applied to three famous English-written literary narrations; namely, Alice in Wonderland (by Lewis Carrol), Dracula (by Bram Stoker) and Sense and Sensibility (by Jane Austen). The results showed that high correlations appear for scales of about 50-200 words, suggesting that at these scales the text contains the stronger coherence. The scaling exponent was not constant along the text, showing important variations with apparent cyclical behavior. An interesting coincidence between the scaling exponent variations and changes in narrative units (e.g., chapters) was found. This suggests that the scaling exponent obtained from the DFA is able to detect changes in narration structure as expressed by the usage of words of different lengths.
An actuator line model simulation with optimal body force projection length scales
Martinez-Tossas, Luis; Churchfield, Matthew J.; Meneveau, Charles
2016-11-01
In recent work (Martínez-Tossas et al. "Optimal smoothing length scale for actuator line models of wind turbine blades", preprint), an optimal body force projection length-scale for an actuator line model has been obtained. This optimization is based on 2-D aerodynamics and is done by comparing an analytical solution of inviscid linearized flow over a Gaussian body force to the potential flow solution of flow over a Joukowski airfoil. The optimization provides a non-dimensional optimal scale ɛ / c for different Joukowski airfoils, where ɛ is the width of the Gaussian kernel and c is the chord. A Gaussian kernel with different widths in the chord and thickness directions can further reduce the error. The 2-D theory developed is extended by simulating a full scale rotor using the optimal body force projection length scales. Using these values, the tip losses are captured by the LES and thus, no additional explicit tip-loss correction is needed for the actuator line model. The simulation with the optimal values provides excellent agreement with Blade Element Momentum Theory. This research is supported by the National Science Foundation (Grant OISE-1243482, the WINDINSPIRE project).
Dependence of exponents on text length versus finite-size scaling for word-frequency distributions
Corral, Álvaro; Font-Clos, Francesc
2017-08-01
Some authors have recently argued that a finite-size scaling law for the text-length dependence of word-frequency distributions cannot be conceptually valid. Here we give solid quantitative evidence for the validity of this scaling law, using both careful statistical tests and analytical arguments based on the generalized central-limit theorem applied to the moments of the distribution (and obtaining a novel derivation of Heaps' law as a by-product). We also find that the picture of word-frequency distributions with power-law exponents that decrease with text length [X. Yan and P. Minnhagen, Physica A 444, 828 (2016), 10.1016/j.physa.2015.10.082] does not stand with rigorous statistical analysis. Instead, we show that the distributions are perfectly described by power-law tails with stable exponents, whose values are close to 2, in agreement with the classical Zipf's law. Some misconceptions about scaling are also clarified.
Hu, S. X.; Michel, D. T.; Edgell, D. H.; Froula, D. H.; Follett, R. K.; Goncharov, V. N.; Myatt, J. F.; Skupsky, S.; Yaakobi, B. [Laboratory for Laser Energetics, University of Rochester, 250 E. River Road, Rochester, New York 14623 (United States)
2013-03-15
Direct-drive-ignition designs with plastic CH ablators create plasmas of long density scale lengths (L{sub n} {>=} 500 {mu}m) at the quarter-critical density (N{sub qc}) region of the driving laser. The two-plasmon-decay (TPD) instability can exceed its threshold in such long-scale-length plasmas (LSPs). To investigate the scaling of TPD-induced hot electrons to laser intensity and plasma conditions, a series of planar experiments have been conducted at the Omega Laser Facility with 2-ns square pulses at the maximum laser energies available on OMEGA and OMEGA EP. Radiation-hydrodynamic simulations have been performed for these LSP experiments using the two-dimensional hydrocode draco. The simulated hydrodynamic evolution of such long-scale-length plasmas has been validated with the time-resolved full-aperture backscattering and Thomson-scattering measurements. draco simulations for CH ablator indicate that (1) ignition-relevant long-scale-length plasmas of L{sub n} approaching {approx}400 {mu}m have been created; (2) the density scale length at N{sub qc} scales as L{sub n}({mu}m) Asymptotically-Equal-To (R{sub DPP} Multiplication-Sign I{sup 1/4}/2); and (3) the electron temperature T{sub e} at N{sub qc} scales as T{sub e}(keV) Asymptotically-Equal-To 0.95 Multiplication-Sign {radical}(I), with the incident intensity (I) measured in 10{sup 14} W/cm{sup 2} for plasmas created on both OMEGA and OMEGA EP configurations with different-sized (R{sub DPP}) distributed phase plates. These intensity scalings are in good agreement with the self-similar model predictions. The measured conversion fraction of laser energy into hot electrons f{sub hot} is found to have a similar behavior for both configurations: a rapid growth [f{sub hot} Asymptotically-Equal-To f{sub c} Multiplication-Sign (G{sub c}/4){sup 6} for G{sub c} < 4] followed by a saturation of the form, f{sub hot} Asymptotically-Equal-To f{sub c} Multiplication-Sign (G{sub c}/4){sup 1.2} for G{sub c} {>=} 4, with the
Length Scale of Free Stream Turbulence and Its Impact on Bypass Transition in a Boundary Layer
J. Grzelak
2017-01-01
Full Text Available An experimental investigation was carried out to study the turbulent flow over a flat plate in a subsonic wind tunnel. The enhanced level of turbulence was generated by five wicker grids with square meshes, and different parameters (diameter of the grid rod d = 0.3 to 3 mm and the grid mesh size M = 1 to 30 mm. The velocity of the flow was measured by means of a 1D hot-wire probe, suitable for measurements in a boundary layer. The main aim of the investigation was to explore the influence of the free stream turbulence length scale on the onset of laminar-turbulent bypass transition in a boundary layer on a flat plate. For this purpose, several transition correlations were presented, including intensity and length scales of turbulence, both at the leading edge of a plate and at the onset of transition. The paper ends with an attempt to create a correlation, which takes into account a simultaneous impact of turbulence intensity and turbulence scale on the boundary layer transition. To assess the isotropy of turbulence, the skewness factor of the flow velocity distribution was determined. Also several longitudinal scales of turbulence were determined and compared (integral scale, dissipation scale, Taylor microscale and Kolmogorov scale for different grids and different velocities of the mean flow U = 4, 6, 10, 15, 20 m/s.
Macmahan, Jamie; Reniers, Ad; Ashley, Will; Thornton, Ed
2012-09-01
Macroscale turbulent coherent flow structures in a natural fast-flowing river were examined with a combination of a novel 2 MHz Acoustic Doppler Beam (ADB) and a Maximum Likelihood Estimator (MLE) to characterize the streamwise horizontal length scales and persistence of coherent flow structures by measuring the frequency (f)-streamwise-wavenumber (ks) energy density velocity spectrum, E(f, ks), for the first time in natural rivers. The ADB was deployed under a range of Froude numbers (0.1-0.6) at high Reynolds numbers (˜106) based on depth and velocity conditions within a gravel bed reach of the Kootenai River, Idaho. The MLE employed on the ADB data increased our ability to describe river motions with relatively long (>10 m) length scales in ˜1 m water depths. The E(f, ks) spectra fell along a ridge described by V = f/ks, where Vis the mean velocity over depth, consistent with Taylor's hypothesis. New, consistent length scale measures are defined based on averaged wavelengths of the low-frequencyE(f, ks) and coherence spectra. Energetic (˜50% of the total spectral energy), low-frequency (f 1 m/s,Lmwere found to be significantly longer than their corresponding coherence lengths, suggesting that the turbulent structures evolve rapidly under these conditions. This is attributed to the stretching and concomitant deformation of preexisting macroturbulent motions by the ubiquitous bathymetry-induced spatial flow accelerations present in a natural gravel bed river.
Length Scales and Turbulent Properties of Magnetic Fields in Simulated Galaxy Clusters
Egan, Hilary; Hallman, Eric; Burns, Jack; Xu, Hao; Collins, David; Li, Hui; Norman, Michael L
2016-01-01
Additional physics beyond standard hydrodynamics is needed to fully model the intracluster medium (ICM); however, as we move to more sophisticated models, it is important to consider the role of magnetic fields and the way the fluid approximation breaks down. This paper represents a first step towards developing a self-consistent model of the ICM by characterizing the statistical properties of magnetic fields in cosmological simulations of galaxy clusters. We find that plasma conditions are largely homogeneous across a range of cluster masses and relaxation states. We also find that the magnetic field length scales are resolution dependent and not based on any particular physical process. Energy transfer mechanisms and scales are also identified, and imply the existence of small scale dynamo action. The scales of the small scale dynamo are resolution limited and driven by numerical resistivity and viscosity.
Xu, Jinglei; Li, Meng; Zhang, Yang; Chen, Longfei
2016-12-01
The von Karman length scale is able to reflect the size of the local turbulence structure. However, it is not suitable for the near wall region of wall-bounded flows, for its value is almost infinite there. In the present study, a simple and novel length scale combining the wall distance and the von Karman length scale is proposed by introducing a structural function. The new length scale becomes the von Karman length scale once local unsteady structures are detected. The proposed method is adopted in a series of turbulent channel flows at different Reynolds numbers. The results show that the proposed length scale with the structural function can precisely simulate turbulence at high Reynolds numbers, even with a coarse grid resolution.
Scaling analysis of random walks with persistence lengths: Application to self-avoiding walks
Granzotti, C. R. F.; Martinez, A. S.; da Silva, M. A. A.
2016-05-01
We develop an approach for performing scaling analysis of N -step random walks (RWs). The mean square end-to-end distance, , is written in terms of inner persistence lengths (IPLs), which we define by the ensemble averages of dot products between the walker's position and displacement vectors, at the j th step. For RW models statistically invariant under orthogonal transformations, we analytically introduce a relation between and the persistence length, λN, which is defined as the mean end-to-end vector projection in the first step direction. For self-avoiding walks (SAWs) on 2D and 3D lattices we introduce a series expansion for λN, and by Monte Carlo simulations we find that λ∞ is equal to a constant; the scaling corrections for λN can be second- and higher-order corrections to scaling for . Building SAWs with typically 100 steps, we estimate the exponents ν0 and Δ1 from the IPL behavior as function of j . The obtained results are in excellent agreement with those in the literature. This shows that only an ensemble of paths with the same length is sufficient for determining the scaling behavior of , being that the whole information needed is contained in the inner part of the paths.
Measurements of the Influence of Integral Length Scale on Stagnation Region Heat Transfer
Vanfossen, G. James; Ching, Chang Y.
1994-01-01
The purpose was twofold: first, to determine if a length scale existed that would cause the greatest augmentation in stagnation region heat transfer for a given turbulence intensity and second, to develop a prediction tool for stagnation heat transfer in the presence of free stream turbulence. Toward this end, a model with a circular leading edge was fabricated with heat transfer gages in the stagnation region. The model was qualified in a low turbulence wind tunnel by comparing measurements with Frossling's solution for stagnation region heat transfer in a laminar free stream. Five turbulence generating grids were fabricated; four were square mesh, biplane grids made from square bars. Each had identical mesh to bar width ratio but different bar widths. The fifth grid was an array of fine parallel wires that were perpendicular to the axis of the cylindrical leading edge. Turbulence intensity and integral length scale were measured as a function of distance from the grids. Stagnation region heat transfer was measured at various distances downstream of each grid. Data were taken at cylinder Reynolds numbers ranging from 42,000 to 193,000. Turbulence intensities were in the range 1.1 to 15.9 percent while the ratio of integral length scale to cylinder diameter ranged from 0.05 to 0.30. Stagnation region heat transfer augmentation increased with decreasing length scale. An optimum scale was not found. A correlation was developed that fit heat transfer data for the square bar grids to within +4 percent. The data from the array of wires were not predicted by the correlation; augmentation was higher for this case indicating that the degree of isotropy in the turbulent flow field has a large effect on stagnation heat transfer. The data of other researchers are also compared with the correlation.
Scaling Between Localization Length and TC in Disordered YBa2Cu3 O6.9
Gauzzi, Andrea; Pavuna, Davor
We quantitatively study the effect of growth-induced reduction of long range structural order on the superconducting transition in epitaxial YBa2Cu3O6.9 films. The corresponding reduction of structural coherence length rc is determined from the width of X-ray diffraction rocking curves. Tc measurements in the films give evidence for the validity of the empirical scaling relation ΔTc~ rc,ab-2, where ΔTc is the disorder-induced reduction of Tc and rc,ab is the structural coherence length in the ab-plane. To explain this algebraic law we propose a simple phenomenological model based on the disorder-induced localization of the charge carriers within each ordered domain of size rc,ab. This picture enables us to precisely determine the Ginzburg-Landau superconducting coherence length in the ab-plane, and we obtain ξab=1.41±0.04 nm.
Length Scales of Magmatic Segments at Intermediate and Fast Spreading Ridges
Boulahanis, B.; Carbotte, S. M.; Klein, E. M.; Smith, D. K.; Cannat, M.
2014-12-01
A synthesis of observations from fast and magmatically-robust intermediate spreading ridges suggest that fine-scale tectonic segments, previously classified as 3rd order, correspond with principle magmatic segments along these ridges, each with their own magmatic plumbing system in the crust and shallow mantle. In this study, we use multi-beam sonar data available for fast and intermediate spreading ridges to determine the length distribution of these segments for comparison with the primary segmentation of the ridge axis found at slower spreading ridges. A study of intermediate, slow and ultraslow-spreading ridges using global satellite-derived bathymetry indicates a dominant segment length of 53 km [Briais and Rabinowicz, J. Geophys. Res. 2002]. However, satellite-derived bathymetry cannot be used to identify fine-scale tectonic segmentation of fast and magmatically-robust intermediate spreading ridges due to the subdued low-relief expression of ridge-axis discontinuities along these spreading rates. This study focuses on the well-mapped regions of the East Pacific Rise between 13.35°S and 18°N, and the Galapagos Spreading Center between 85° and 95.38° W. We reexamine tectonic segmentation of the ridge axis previously identified in the literature and modify the locations of ridge-axis discontinuities defining segment ends in regions where modern multi-beam bathymetric data coverage has improved relative to that available in early studies. Discontinuities of first, second, and third order are used to define tectonic segment lengths. Initial results show a mean segment length of 42 km (standard deviation of 27 km) and a median of 33 km, with 85 segments studied, similar to the segment length distributions observed at slower spreading ridges. To further evaluate the hypothesis of principle magmatic segments, we also examine the relationship between fine-scale tectonic segmentation and properties of the crustal magmatic system imaged in prior seismic studies of
Application of DDES and IDDES with shear layer adapted subgrid length-scale to separated flows
Guseva, E. K.; Garbaruk, A. V.; Strelets, M. Kh
2016-11-01
A comparative study is conducted of the original versions of Delayed Detached- Eddy Simulation (DDES) and Improved DDES (IDDES) and these approaches combined with “shear-layer-adapted” (SLA) subgrid length-scale proposed recently for resolving the issue of delayed RANS-to-LES transition in separated shear layers in global hybrid RANS-LES approaches. Computations were carried out of two separated flows: a transonic flow past M 219 cavity and a subsonic flow over NASA wall mounted hump. Results of the computations suggest that the use of the SLA subgrid length-scale considerably accelerates transition to resolved three-dimensional turbulence in the separated shear layers and substantially improves agreement with the experimental data.
The length-scale dependence of strain in networks by SANS
Pyckhout-Hintzen, W.; Botti, A.; Heinrich, M.; Richter, D. [IFF-Forschungszentrum Juelich, 52425 Juelich (Germany); Westermann, S. [Goodyear, 7750 Colmar-Berg (Luxembourg); Straube, E. [University of Halle, FB Physik, 06099 Halle (Germany)
2002-07-01
We present a SANS study of the length-scale dependence of chain deformation by means of a suitable labeling in dense, cross-linked elastomers of the HDH-type. This length scale is controlled by the size of the label as well as the cross-link density. The results are compared to long homopolymers. The data are analyzed by means of the tube model of topology in rubber elasticity in combination with the random-phase approximation (RPA) to account for interchain correlations. Chain degradation during cross linking is treated by the standard RPA approach for polydisperse multicomponent systems. A transition from locally freely fluctuating to tube-constrained segmental motion was observed. (orig.)
The length-scale dependence of strain in networks by SANS
Pyckhout-Hintzen, W; Heinrich, M; Richter, D; Westermann, S; Straube, E
2002-01-01
We present a SANS study of the length-scale dependence of chain deformation by means of a suitable labeling in dense, cross-linked elastomers of the HDH-type. This length scale is controlled by the size of the label as well as the cross-link density. The results are compared to long homopolymers. The data are analyzed by means of the tube model of topology in rubber elasticity in combination with the random-phase approximation (RPA) to account for interchain correlations. Chain degradation during cross linking is treated by the standard RPA approach for polydisperse multicomponent systems. A transition from locally freely fluctuating to tube-constrained segmental motion was observed. (orig.)
Jamshidian, M., E-mail: mostafa.jamshidian@gmail.com [Department of Mechanical Engineering, Isfahan University of Technology, Isfahan (Iran, Islamic Republic of); Institute of Structural Mechanics, Bauhaus-University Weimar, Marienstrasse 15, 99423 Weimar (Germany); Rabczuk, T., E-mail: timon.rabczuk@uni-weimar.de [Institute of Structural Mechanics, Bauhaus-University Weimar, Marienstrasse 15, 99423 Weimar (Germany); School of Civil, Environmental and Architectural Engineering, Korea University, Seoul (Korea, Republic of)
2014-03-15
We establish the correlation between the diffuse interface and sharp interface descriptions for stressed grain boundary migration by presenting analytical solutions for stressed migration of a circular grain boundary in a bicrystalline phase field domain. The validity and accuracy of the phase field model is investigated by comparing the phase field simulation results against analytical solutions. The phase field model can reproduce precise boundary kinetics and stress evolution provided that a thermodynamically consistent theory and proper expressions for model parameters in terms of physical material properties are employed. Quantitative phase field simulations are then employed to investigate the effect of microstructural length scale on microstructure and texture evolution by stressed grain growth in an elastically deformed polycrystalline aggregate. The simulation results reveal a transitional behaviour from normal to abnormal grain growth by increasing the microstructural length scale.
A mass-length scaling law for modeling muscle strength in the lower limb.
Correa, Tomas A; Pandy, Marcus G
2011-11-10
Musculoskeletal computer models are often used to study muscle function in children with and without impaired mobility. Calculations of muscle forces depend in part on the assumed strength of each muscle, represented by the peak isometric force parameter, which is usually based on measurements obtained from cadavers of adult donors. The aim of the present study was twofold: first, to develop a method for scaling lower-limb peak isometric muscle forces in typically-developing children; and second, to determine the effect of this scaling method on model calculations of muscle forces obtained for normal gait. Muscle volumes were determined from magnetic resonance (MR) images obtained from ten children aged from 7 to 13yr. A new mass-length scaling law was developed based on the assumption that muscle volume and body mass are linearly related, which was confirmed by the obtained volume and body mass data. Two musculoskeletal models were developed for each subject: one in which peak isometric muscle forces were estimated using the mass-length scaling law; and another in which these parameters were determined directly from the MR-derived muscle volumes. Musculoskeletal modeling and quantitative gait analysis were then used to calculate lower-limb muscle forces in normal walking. The patterns of muscle forces predicted by the model with scaled peak isometric force values were similar to those predicted by the MR-based model, implying that assessments of muscle function obtained from these two methods are practically equivalent. These results support the use of mass-length scaling in the development of subject-specific musculoskeletal models of children.
Frantziskonis, George N.; Gur, Sourav
2017-06-01
Thermally induced phase transformation in NiTi shape memory alloys (SMAs) shows strong size and shape, collectively termed length scale effects, at the nano to micrometer scales, and that has important implications for the design and use of devices and structures at such scales. This paper, based on a recently developed multiscale model that utilizes molecular dynamics (MDs) simulations at small scales and MD-verified phase field (PhF) simulations at larger scales, reports results on specific length scale effects, i.e. length scale effects in martensite phase fraction (MPF) evolution, transformation temperatures (martensite and austenite start and finish) and in the thermally cyclic transformation between austenitic and martensitic phase. The multiscale study identifies saturation points for length scale effects and studies, for the first time, the length scale effect on the kinetics (i.e. developed internal strains) in the B19‧ phase during phase transformation. The major part of the work addresses small scale single crystals in specific orientations. However, the multiscale method is used in a unique and novel way to indirectly study length scale and grain size effects on evolution kinetics in polycrystalline NiTi, and to compare the simulation results to experiments. The interplay of the grain size and the length scale effect on the thermally induced MPF evolution is also shown in this present study. Finally, the multiscale coupling results are employed to improve phenomenological material models for NiTi SMA.
Junzhong Xu
Full Text Available Measurements of apparent diffusion coefficient (ADC using magnetic resonance imaging (MRI have been suggested as potential imaging biomarkers for monitoring tumor response to treatment. However, conventional pulsed-gradient spin echo (PGSE methods incorporate relatively long diffusion times, and are usually sensitive to changes in cell density and necrosis. Diffusion temporal spectroscopy using the oscillating gradient spin echo (OGSE sequence is capable of probing short length scales, and may detect significant intracellular microstructural changes independent of gross cell density changes following anti-cancer treatment. To test this hypothesis, SW620 xenografts were treated by barasertib (AZD1152, a selective inhibitor of Aurora B kinase which causes SW620 cancer cells to develop polyploidy and increase in size following treatment, ultimately leading to cell death through apoptosis. Following treatment, the ADC values obtained by both the PGSE and low frequency OGSE methods increased. However, the ADC values at high gradient frequency (i.e. short diffusion times were significantly lower in treated tumors, consistent with increased intracellular restrictions/hindrances. This suggests that ADC values at long diffusion times are dominated by tumor microstructure at long length scales, and may not convey unambiguous information of subcellular space. While the diffusion temporal spectroscopy provides more comprehensive means to probe tumor microstructure at various length scales. This work is the first study to probe intracellular microstructural variations due to polyploidy following treatment using diffusion MRI in vivo. It is also the first observation of post-treatment ADC changes occurring in opposite directions at short and long diffusion times. The current study suggests that temporal diffusion spectroscopy potentially provides pharmacodynamic biomarkers of tumor early response which distinguish microstructural variations following
Multi-Length-Scale Morphologies Driven by Mixed Additives in Porphyrin-Based Organic Photovoltaics.
Gao, Ke; Miao, Jingsheng; Xiao, Liangang; Deng, Wanyuan; Kan, Yuanyuan; Liang, Tianxiang; Wang, Cheng; Huang, Fei; Peng, Junbiao; Cao, Yong; Liu, Feng; Russell, Thomas P; Wu, Hongbin; Peng, Xiaobin
2016-06-01
A new category of deep-absorbing small molecules is developed. Optimized devices driven by mixed additives show a remarkable short-circuit current of ≈20 mA cm(-2) and a highest power conversion efficiency of 9.06%. A multi-length-scale morphology is formed, which is fully characterized by resonant soft X-ray scattering, high-angle annular dark film image transmission electron microscopy, etc.
Energy Dependence and Scaling Property of Localization Length near a Gapped Flat Band
Ge, Li
2015-01-01
Using a tight-binding model for a one-dimensional Lieb lattice, we show that the localization length near a gapped flat band behaves differently from the typical Urbach tail in a band gap: instead of reducing monotonically as the energy E moves away from the flat band energy E_{FB}, the presence of the flat band causes a nonmonotonic energy dependence of the localization length. This energy dependence follows a scaling property when the energy is within the spread (W) of uniformly distributed diagonal disorder, i.e. the localization length is only a function of (E-E_{FB})/W. Several other lattices are compared to distinguish the effect of the flat band on the localization length, where we eliminate, shift, or duplicate the flat band, without changing the dispersion relations of other bands. Using the top right element of the Green's matrix, we derive an analytical relation between the density of states and the localization length, which shines light on these properties of the latter, including a summation rul...
LPI Thresholds in Longer Scale Length Plasmas Driven by the Nike Laser*
Weaver, J.; Oh, J.; Phillips, L.; Afeyan, B.; Seely, J.; Kehne, D.; Brown, C.; Obenschain, S.; Serlin, V.; Schmitt, A. J.; Feldman, U.; Holland, G.; Lehmberg, R. H.; McLean, E.; Manka, C.
2010-11-01
The Krypton-Fluoride (KrF) laser is an attractive driver for inertial confinement fusion due to its short wavelength (248nm), large bandwidth (1-3 THz), and beam smoothing by induced spatial incoherence. Experiments with the Nike KrF laser have demonstrated intensity thresholds for laser plasma instabilities (LPI) higher than reported for other high power lasers operating at longer wavelengths (>=351 nm). The previous Nike experiments used short pulses (350 ps FWHM) and small spots (<260 μm FWHM) that created short density scale length plasmas (Ln˜50-70 μm) from planar CH targets and demonstrated the onset of two-plasmon decay (2φp) at laser intensities ˜2x10^15 W/cm^2. This talk will present an overview of the current campaign that uses longer pulses (0.5-4.0 ns) to achieve greater density scale lengths (Ln˜100-200 μm). X-rays, emission near ^1/2φo and ^3/2φo harmonics, and reflected laser light have been monitored for onset of 2φp. The longer density scale lengths will allow better comparison to results from other laser facilities. *Work supported by DoE/NNSA and ONR.
Aberration-Corrected Electron Beam Lithography at the One Nanometer Length Scale.
Manfrinato, Vitor R; Stein, Aaron; Zhang, Lihua; Nam, Chang-Yong; Yager, Kevin G; Stach, Eric A; Black, Charles T
2017-08-09
Patterning materials efficiently at the smallest length scales is a longstanding challenge in nanotechnology. Electron-beam lithography (EBL) is the primary method for patterning arbitrary features, but EBL has not reliably provided sub-4 nm patterns. The few competing techniques that have achieved this resolution are orders of magnitude slower than EBL. In this work, we employed an aberration-corrected scanning transmission electron microscope for lithography to achieve unprecedented resolution. Here we show aberration-corrected EBL at the one nanometer length scale using poly(methyl methacrylate) (PMMA) and have produced both the smallest isolated feature in any conventional resist (1.7 ± 0.5 nm) and the highest density patterns in PMMA (10.7 nm pitch for negative-tone and 17.5 nm pitch for positive-tone PMMA). We also demonstrate pattern transfer from the resist to semiconductor and metallic materials at the sub-5 nm scale. These results indicate that polymer-based nanofabrication can achieve feature sizes comparable to the Kuhn length of PMMA and ten times smaller than its radius of gyration. Use of aberration-corrected EBL will increase the resolution, speed, and complexity in nanomaterial fabrication.
Isterling, William M; Dally, Bassam B; Alwahabi, Zeyad T; Dubovinsky, Miro; Wright, Daniel
2012-01-01
Narrow laser beams directed from aircraft may at times pass through the exhaust plume of the engines and potentially degrade some of the laser beam characteristics. This paper reports on controlled studies of laser beam deviation arising from propagation through turbulent hot gases, in a well-characterized laboratory burner, with conditions of relevance to aircraft engine exhaust plumes. The impact of the temperature, laser wavelength, and turbulence length scale on the beam deviation has been investigated. It was found that the laser beam displacement increases with the turbulent integral length scale. The effect of temperature on the laser beam angular deviation, σ, using two different laser wavelengths, namely 4.67 μm and 632.8 nm, was recorded. It was found that the beam deviation for both wavelengths may be semiempirically modeled using a single function of the form, σ=a(b+(1/T)(2))(-1), with two parameters only, a and b, where σ is in microradians and T is the temperature in °C.
Gokhale, A.M.; Yang, S. [Georgia Inst. of Tech., Atlanta, GA (United States). Dept. of Materials Science and Engineering
1999-09-01
Microstructures of engineering alloys often contain features at widely different length scales. In this contribution, a digital image processing technique is presented to incorporate the effect of features at higher length scales on the damage evolution and local fracture processes occurring at lower length scales. The method is called M-SLIP: Microstructural Scale Linking by Image Processing. The technique also enables incorporation of the real microstructure at different length scales in the finite element (FE)-based simulations. The practical application of the method is demonstrated via FE analysis on the microstructure of an aluminum cast alloy (A356), where the length scales of micropores and silicon particles differ by two orders of magnitude. The simulation captures the effect of nonuniformly distributed micropores at length scales of 200 to 500 {micro}m on the local stresses and strains around silicon particles that are at the length scales of 3 to 5 {micro}m. The procedure does not involve any simplifying assumptions regarding the microstructural geometry, and therefore, it is useful to model the mechanical response of the real multi-length scale microstructures of metals and alloys.
Meier, Andrea R; Schmuck, Ute; Meloro, Carlo; Clauss, Marcus; Hofmann, Reinhold R
2016-03-01
Various morphological measures demonstrate convergent evolution in ruminants with their natural diet, in particular with respect to the browser/grazer dichotomy. Here, we report quantitative macroanatomical measures of the tongue (length and width of specific parts) of 65 ruminant species and relate them to either body mass (BM) or total tongue length, and to the percentage of grass in the natural diet (%grass). Models without and with accounting for the phylogenetic structures of the dataset were used, and models were ranked using Akaike's Information Criterion. Scaling relationships followed geometric principles, that is, length measures scaled with BM to the power of 0.33. Models that used tongue length rather than BM as a body size proxy were consistently ranked better, indicating that using size proxies that are less susceptible to a wider variety of factors (such as BM that fluctuates with body condition) should be attempted whenever possible. The proportion of the freely mobile tongue tip of the total tongue (and hence also the corpus length) was negatively correlated to %grass, in accordance with concepts that the feeding mechanism of browsers requires more mobile tongues. It should be noted that some nonbrowsers, such as cattle, use a peculiar mechanism for grazing that also requires long, mobile tongues, but they appear to be exceptions. A larger corpus width with increasing %grass corresponds to differences in snout shape with broader snouts in grazers. The Torus linguae is longer with increasing %grass, a finding that still warrants functional interpretation. This study shows that tongue measures covary with diet in ruminants. In contrast, the shape of the tongue (straight or "hourglass-shaped" as measured by the ratio of the widest and smallest corpus width) is unrelated to diet and is influenced strongly by phylogeny.
Freunberger, S. A.
2007-07-01
This dissertation is concerned with the development, experimental diagnostics and mathematical modelling and simulation of polymer electrolyte fuel cells (PEFC). The central themes throughout this thesis are the closely interlinked phenomena of mass and charge transfer. In the face of developing a PEFC system for vehicle propulsion these phenomena are scrutinized on a broad range of relevant scales. Starting from the material related level of the membrane and the gas diffusion layer (GDL) we turn to length scales, where structural features of the cell additionally come into play. These are the scale of flow channels and ribs, the single cell and the cell stack followed by the cell, stack, and system development for an automotive power train. In Chapter 3 selected fundamental material models and properties, respectively, are explored that are crucial for the mathematical modelling and simulation of PEFC, as needed in some succeeding parts of this work. First, established mathematical models for mass and charge transfer in the membrane are compared within the framework of the membrane electrode assembly (MEA), which represents the electrochemical unit. Second, reliable values for effective diffusivities in the GDLs which are vital for the simulation of gaseous mass transport are measured. Therefore, a method is developed that allows measuring this quantity both as a function of compression and direction as this is a prerequisite of sophisticated more-dimensional numerical PEFC-models. Besides the cross section of the catalyst layer (CL) mass transfer under channels and ribs is considered as a major source of losses in particular under high load operation. As up to now there have been solely non-validated theoretical investigations, in Chapter 4 an experimental method is developed that is for the first time capable of resolving the current density distribution on the this scale. For this, the electron conductors in the cell are considered as 2-dimensional shunt
Fracture Testing at Small-Length Scales: From Plasticity in Si to Brittleness in Pt
Jaya, B. Nagamani; Jayaram, Vikram
2016-01-01
The field of micro-/nano-mechanics of materials has been driven, on the one hand by the development of ever smaller structures in devices, and, on the other, by the need to map property variations in large systems that are microstructurally graded. Observations of `smaller is stronger' have also brought in questions of accompanying fracture property changes in the materials. In the wake of scattered articles on micro-scale fracture testing of various material classes, this review attempts to provide a holistic picture of the current state of the art. In the process, various reliable micro-scale geometries are shown, challenges with respect to instrumentation to probe ever smaller length scales are discussed and examples from recent literature are put together to exhibit the expanse of unusual fracture response of materials, from ductility in Si to brittleness in Pt. Outstanding issues related to fracture mechanics of small structures are critically examined for plausible solutions.
Lower Length Scale Model Development for Embrittlement of Reactor Presure Vessel Steel
Zhang, Yongfeng [Idaho National Lab. (INL), Idaho Falls, ID (United States); Schwen, Daniel [Idaho National Lab. (INL), Idaho Falls, ID (United States); Chakraborty, Pritam [Idaho National Lab. (INL), Idaho Falls, ID (United States); Bai, Xianming [Idaho National Lab. (INL), Idaho Falls, ID (United States)
2016-09-01
This report summarizes the lower-length-scale effort during FY 2016 in developing mesoscale capabilities for microstructure evolution, plasticity and fracture in reactor pressure vessel steels. During operation, reactor pressure vessels are subject to hardening and embrittlement caused by irradiation induced defect accumulation and irradiation enhanced solute precipitation. Both defect production and solute precipitation start from the atomic scale, and manifest their eventual effects as degradation in engineering scale properties. To predict the property degradation, multiscale modeling and simulation are needed to deal with the microstructure evolution, and to link the microstructure feature to material properties. In this report, the development of mesoscale capabilities for defect accumulation and solute precipitation are summarized. A crystal plasticity model to capture defect-dislocation interaction and a damage model for cleavage micro-crack propagation is also provided.
Scaling of the critical free length for progressive unfolding of self-bonded graphene
Kwan, Kenny; Cranford, Steven W., E-mail: s.cranford@neu.edu [Laboratory of Nanotechnology in Civil Engineering (NICE), Department of Civil and Environmental Engineering, Northeastern University, 400 Snell Engineering, 360 Huntington Avenue, Boston, Massachusetts 02115 (United States)
2014-05-19
Like filled pasta, rolled or folded graphene can form a large nanocapsule surrounding a hollow interior. Use as a molecular carrier, however, requires understanding of the opening of such vessels. Here, we investigate a monolayer sheet of graphene as a theoretical trial platform for such a nanocapsule. The graphene is bonded to itself via aligned disulfide (S-S) bonds. Through theoretical analysis and atomistic modeling, we probe the critical nonbonded length (free length, L{sub crit}) that induces fracture-like progressive unfolding as a function of folding radius (R{sub i}). We show a clear linear scaling relationship between the length and radius, which can be used to determine the necessary bond density to predict mechanical opening/closing. However, stochastic dissipated energy limits any exact elastic formulation, and the required energy far exceeds the dissociation energy of the S-S bond. We account for the necessary dissipated kinetic energy through a simple scaling factor (Ω), which agrees well with computational results.
Decoherence of trapped bosons by buffer gas scattering: What length scales matter?
Gilz, Lukas; Anglin, James R
2014-01-01
We ask and answer a basic question about the length scales involved in quantum decoherence: how far apart in space do two parts of a quantum system have to be, before a common quantum environment decoheres them as if they were entirely separate? We frame this question specifically in a cold atom context. How far apart do two populations of bosons have to be, before an environment of thermal atoms of a different species (`buffer gas') responds to their two particle numbers separately? An initial guess for this length scale is the thermal coherence length of the buffer gas; we show that a standard Born-Markov treatment partially supports this guess, but predicts only inverse-square saturation of decoherence rates with distance, and not the much more abrupt Gaussian behavior of the buffer gas's first-order coherence. We confirm this Born-Markov result with a more rigorous theory, based on an exact solution of a two-scatterer scattering problem, which also extends the result beyond weak scattering. Finally, howev...
An estimation formula for the average path length of scale-free networks
Li Ying; Cao Hong-Duo; Shan Xiu-Ming; Ren Yong
2008-01-01
A universal estimation formula for the average path length of scale free networks is given in this paper. Different from other estimation formulas, most of which use the size of network, N, as the only parameter, two parameters including N and a second parameter α are included in our formula. The parameter α is the power-law exponent, which represents the local connectivity property of a network. Because of this, the formula captures an important property that the local connectivity property at a microscopic level can determine the global connectivity of the whole network. The use of this new parameter distinguishes this approach from the other estimation formulas, and makes it a universal estimation formula, which can be applied to all types of scale-free networks. The conclusion is made that the small world feature is a derivative feature of a scale free network. If a network follows the power-law degree distribution, it must be a small world network. The power-law degree distribution property, while making the network economical, preserves the efficiency through this small world property when the network is scaled up. In other words, a real scale-free network is scaled at a relatively small cost and a relatively high efficiency, and that is the desirable result of self-organization optimization.
Voss, Florian; Schmidt, Volker
2009-01-01
We consider spatial stochastic models, which can be applied e.g. to telecommunication networks with two hierarchy levels. In particular, we consider two Cox processes concentrated on the edge set of a random tessellation, where the points can describe the locations of low-level and high-level network components, respectively, and the edge set the underlying infrastructure of the network, like road systems, railways, etc. Furthermore, each low-level component is marked with the shortest path along the edge set to the nearest high-level component. We investigate the typical shortest path length of the resulting marked point process, which is an important characteristic e.g. in performance analysis and planning of telecommunication networks. In particular, we show that its distribution converges to simple parametric limit distributions if a certain scaling factor converges to zero and infinity, respectively. This can be used to approximate the density of the typical shortest path length by analytical formulae.
Chen, Wei; Legner, Markus; Rüegg, Andreas; Sigrist, Manfred
2017-02-01
The correlation functions related to topological phase transitions in inversion-symmetric lattice models described by 2 ×2 Dirac Hamiltonians are discussed. In one dimension, the correlation function measures the charge-polarization correlation between Wannier states at different positions, while in two dimensions it measures the itinerant-circulation correlation between Wannier states. The correlation function is nonzero in both the topologically trivial and nontrivial states, and allows us to extract a correlation length that diverges at topological phase transitions. The correlation length and the curvature function that defines the topological invariants are shown to have universal critical exponents, allowing the notion of universality classes to be introduced. Particularly in two dimensions, the universality class is determined by the orbital symmetry of the Dirac model. The scaling laws that constrain the critical exponents are revealed, and are predicted to be satisfied even in interacting systems, as demonstrated in an interacting topological Kondo insulator.
An evaluation of the hydrologic relevance of lateral flow in snow at hillslope and catchment scales
David Eiriksson; Michael Whitson; Charles H. Luce; Hans Peter Marshall; John Bradford; Shawn G. Benner; Thomas Black; Hank Hetrick; James P. McNamara
2013-01-01
Lateral downslope flow in snow during snowmelt and rain-on-snow (ROS) events is a well-known phenomenon, yet its relevance to water redistribution at hillslope and catchment scales is not well understood. We used dye tracers, geophysical methods, and hydrometric measurements to describe the snow properties that promote lateral flow, assess the relative velocities of...
Reneman, Michiel F.; Geertzen, Jan H. B.; Jorritsma, Wim; Knol-de Vries, Grietje; Dijkstra, Pieter U.
2012-01-01
To investigate relevant change on the Neck Pain and Disability Scale (NPAD) and Neck Disability Index (NDI) and which questionnaire is the most responsive in patients with non-specific chronic neck pain (CNP). Seventy-six patients with non-specific CNP in an outpatient tertiary rehabilitation settin
de Bruin, E.J.; van Kampen, R.K.A.; van Kooten, T.; Meijer, A.M.
2014-01-01
Objective: This study investigated reliability, validity, and clinical relevance of the Adolescent Sleep Hygiene Scale (ASHS) in Dutch adolescents. Methods: The Dutch translation of the ASHS was administered to 186 normal-sleeping adolescents and 112 adolescents with insomnia. Their sleep variables
de Bruin, E.J.; van Kampen, R.K.A.; van Kooten, T.; Meijer, A.M.
2014-01-01
Objective: This study investigated reliability, validity, and clinical relevance of the Adolescent Sleep Hygiene Scale (ASHS) in Dutch adolescents. Methods: The Dutch translation of the ASHS was administered to 186 normal-sleeping adolescents and 112 adolescents with insomnia. Their sleep variables
Analysis of Average Shortest-Path Length of Scale-Free Network
Guoyong Mao
2013-01-01
Full Text Available Computing the average shortest-path length of a large scale-free network needs much memory space and computation time. Hence, parallel computing must be applied. In order to solve the load-balancing problem for coarse-grained parallelization, the relationship between the computing time of a single-source shortest-path length of node and the features of node is studied. We present a dynamic programming model using the average outdegree of neighboring nodes of different levels as the variable and the minimum time difference as the target. The coefficients are determined on time measurable networks. A native array and multimap representation of network are presented to reduce the memory consumption of the network such that large networks can still be loaded into the memory of each computing core. The simplified load-balancing model is applied on a network of tens of millions of nodes. Our experiment shows that this model can solve the load-imbalance problem of large scale-free network very well. Also, the characteristic of this model can meet the requirements of networks with ever-increasing complexity and scale.
On the influence of free-stream turbulence length scales on boundary-layer transition
Fransson, Jens; Shahinfar, Shahab
2015-11-01
A measurement campaign on the free-stream turbulence (FST) induced boundary layer transition has been carried out in the Minimum-Turbulence-Level wind tunnel at KTH. Previous numerical investigations where the turbulence intensity (Tu) has been kept constant, while the integral length scale (Λx) has been varied, have shown that the transition location is advanced for increasing Λx. The present measurement campaign has been carried out using hot-wire anemometry and consists of 42 unique FST conditions with thorough measurements throughout the transitional region. Unlike other extensive FST induced transition measurements the free-stream velocity was here kept constant for all cases, implying that the boundary layer scale is locked up to transition onset. Our measurements confirm previous results on the advancement of the transition location with increasing Λx for low to moderate Tu levels, but show the opposite effect for higher levels, i.e. a delay in the transition location for larger Λx, which to the knowledge of the present authors so far is unreported. In addition, the common belief that the FST length scales have a negligible effect on the transition location with regards to the Tu level does not seem to be fully true.
A Generic Length-scale Equation For Second-order Turbulence Models of Oceanic Boundary Layers
Umlauf, L.; Burchard, H.
A generic transport equation for a generalized length-scale in second-order turbulence closure models for geophysical boundary layers is suggested. This variable consists of the products of powers of the turbulent kinetic energy, k, and the integral length-scale, l. The new approach generalizes traditional second-order models used in geophysical boundary layer modelling, e.g. the Mellor-Yamada model and the k- model, which, however, can be recovered as special cases. It is demonstrated how this new model can be calibrated with measurements in some typical geophysical boundary layer flows. As an example, the generic model is applied to the uppermost oceanic boundary layer directly influenced by the effects of breaking surface waves. Recent measurements show that in this layer the classical law of the wall is invalid, since there turbulence is dominated by turbulent transport of TKE from above, and not by shear-production. A widely accepted approach to describe the wave-affected layer with a one-equation turbulence model was suggested by Craig and Banner (1994). Here, some deficien- cies of their solutions are pointed out and a generalization of their ideas for the case of two-equation models is suggested. Direct comparison with very recently obtained measurements of the dissipation rate, , in the wave-affected boundary layer with com- puted results clearly demonstrate that only the generic two-equation model yields cor- rect predictions for the profiles of and the turbulent length scale, l. Also, the pre- dicted velocity profiles in the wave-affected layer, important e.g. for the interpretation of surface drifter experiments, are reproduced correctly only by the generic model. Implementation and computational costs of the generic model are comparable with traditonal two-equation models.
Abu Al-Rub, Rashid Kamel
Structural materials display a strong size-dependence when deformed non-uniformly into the inelastic range: smaller is stronger. This effect has important implications for an increasing number of applications in structural failure, electronics, functional coatings, composites, micro-electro-mechanical systems (MEMS), nanostructured materials, micro/nanometer fabrication technologies, etc. The mechanical behavior of these applications cannot be characterized by classical (local) continuum theories because they incorporate no, 'material length scales' and consequently predict no size effects. On the other hand, it is still not possible to perform quantum and atomistic simulations on realistic time and structures. It is therefore necessary to develop a scale-dependent continuum theory bridging the gap between the classical continuum theories and the atomistic simulations in order to be able to design the size-dependent structures of modern technology. Nonlocal rate-dependent and gradient-dependent theories of plasticity and damage are developed in this work for this purpose. We adopt a multi-scale, hierarchical thermodynamic consistent framework to construct the material constitutive relations for the scale-dependent plasticity/damage behavior. Material length scales are implicitly and explicitly introduced into the governing equations through material rate-dependency (viscosity) and coefficients of spatial higher-order gradients of one or more material state variables, respectively. The proposed framework is implemented into the commercially well-known finite element software ABAQUS. The finite element simulations of material instability problems converge to meaningful results upon further refinement of the finite element mesh, since the width of the fracture process zone (shear band) is determined by the intrinsic material length scale; while the classical continuum theories fail to address this problem. It is also shown that the proposed theory is successful for
Horkay, Ferenc; Falus, Peter; Hecht, Anne-Marie; Geissler, Erik (CNRS-UMR); (NIH); (ILL)
2010-12-07
In solutions of the charged semirigid biopolymer hyaluronic acid in salt-free conditions, the diffusion coefficient D{sub NSE} measured at high transfer momentum q by neutron spin echo is more than an order of magnitude smaller than that determined by dynamic light scattering, D{sub DLS}. This behavior contrasts with neutral polymer solutions. With increasing salt content, D{sub DLS} approaches D{sub NSE}, which is independent of ionic strength. Contrary to theoretical expectation, the ion-polymer coupling, which dominates the low q dynamics of polyelectrolyte solutions, already breaks down at distance scales greater than the Debye-Hueckel length.
Lab on a chip Canada--rapid diffusion over large length scales.
Juncker, David; Wheeler, Aaron R; Sinton, David
2013-07-07
The roots of lab on a chip in Canada are deep, comprising of some of the earliest contributions and first demonstrations of the potential of microfluidic chips. In an editorial leading off this special issue, Jed Harrison of University of Alberta reflects on these early days and Canada's role in the field's development (DOI: 10.1039/c3lc50522g). Over the last decade, microfluidics and lab-on-a-chip research efforts grew exponentially - rapidly diffusing across the vast Canadian length scales.
Optimal Heavy-Traffic Queue Length Scaling in an Incompletely Saturated Switch
Maguluri, Siva Theja; Burle, Sai Kiran; Srikant, R.
2016-01-01
We consider an input queued switch operating under the MaxWeight scheduling algorithm. This system is interesting to study because it is a model for Internet routers and data center networks. Recently, it was shown that the MaxWeight algorithm has optimal heavy-traffic queue length scaling when all ports are uniformly saturated. Here we consider the case when an arbitrary number of ports are saturated (which we call the incompletely saturated case), and each port is allowed to saturate at a d...
Explanation of the values of Hack's drainage basin, river length scaling exponent
Hunt, A. G.
2015-08-01
Percolation theory can be used to find water flow paths of least resistance. The application of percolation theory to drainage networks allows identification of the range of exponent values that describe the tortuosity of rivers in real river networks, which is then used to generate the observed scaling between drainage basin area and channel length, a relationship known as Hack's law. Such a theoretical basis for Hack's law allows interpretation of the range of exponent values based on an assessment of the heterogeneity of the substrate.
Hunt, Allen G.
2016-04-01
Percolation theory can be used to find water flow paths of least resistance. Application of percolation theory to drainage networks allows identification of the range of exponent values that describe the tortuosity of rivers in real river networks, which is then used to generate the observed scaling between drainage basin area and channel length, a relationship known as Hack's law. Such a theoretical basis for Hack's law may allow interpretation of the range of exponent values based on an assessment of the heterogeneity of the substrate.
Lead Selenide Nanostructures Self-Assembled across Multiple Length Scales and Dimensions
Evan K. Wujcik
2016-01-01
Full Text Available A self-assembly approach to lead selenide (PbSe structures that have organized across multiple length scales and multiple dimensions has been achieved. These structures consist of angstrom-scale 0D PbSe crystals, synthesized via a hot solution process, which have stacked into 1D nanorods via aligned dipoles. These 1D nanorods have arranged into nanoscale 2D sheets via directional short-ranged attraction. The nanoscale 2D sheets then further aligned into larger 2D microscale planes. In this study, the authors have characterized the PbSe structures via normal and cryo-TEM and EDX showing that this multiscale multidimensional self-assembled alignment is not due to drying effects. These PbSe structures hold promise for applications in advanced materials—particularly electronic technologies, where alignment can aid in device performance.
Electroweak symmetries from the topology of deformed spacetime with minimal length scale
Gresnigt, Niels G
2015-01-01
Lie-type deformations provide a systematic way of generalising the symmetries of modern physics. Deforming the isometry group of Minkowski spacetime through the introduction of a minimal length scale $\\ell$ leads to anti de Sitter spacetime with isometry group $SO(2,3)$. Quantum spacetime on scales of the order $\\ell$ therefore carries negative curvature. Considering extended particles of characteristic size $\\ell$ carrying topological information and requiring that their topological properties be compatible with those of the underlying spacetime, we show that electroweak symmetries emerge from the maximal compact subgroup of the anti de Sitter isometry group in a way that is consistent with no-go theorems. It is speculated that additional deformation outside the Lie-algebraic framework, such as $q$-deformations, could likewise provide an explanation of the origin of the strong force.
Application of nonlocal models to nano beams. Part I: Axial length scale effect.
Kim, Jun-Sik
2014-10-01
Applicability of nonlocal models to nano-beams is discussed in terms of physical implications via the similarity between a nonlocal Euler-Bernoulli (EB) beam theory and a classical Rankine-Timoshenko (RT) beam theory. The nonlocal EB beam model, Eringen's model, is briefly reviewed and the classical RT beam theory is recast by the primary variables of the EB model. A careful comparison of these two models reveals that the scale parameter used to the Eringen's model has a strike resemblance to the shear flexibility in the RT model. This implies that the nonlocal model employed in literature consider the axial length scale effect only. In addition, the paradox for a cantilevered nano-beam subjected to tip shear force is clearly explained by finding appropriate displacement prescribed boundary conditions.
Relations between overturning length scales at the Spanish planetary boundary layer
López, Pilar; Cano, José L.
2016-04-01
We analyze the behavior of the maximum Thorpe displacement (dT)max and the Thorpe scale LTat the atmospheric boundary layer (ABL), extending previous research with new data and improving our studies related to the novel use of the Thorpe method applied to ABL. The maximum Thorpe displacements vary between -900 m and 950 m for the different field campaigns. The maximum Thorpe displacement is always greater under convective conditions than under stable ones, independently of its sign. The Thorpe scale LT ranges between 0.2 m and 680 m for the different data sets which cover different stratified mixing conditions (turbulence shear-driven and convective regions). The Thorpe scale does not exceed several tens of meters under stable and neutral stratification conditions related to instantaneous density gradients. In contrast, under convective conditions, Thorpe scales are relatively large, they exceed hundreds of meters which may be related to convective bursts. We analyze the relation between (dT)max and the Thorpe scale LT and we deduce that they verify a power law. We also deduce that there is a difference in exponents of the power laws for convective conditions and shear-driven conditions. These different power laws could identify overturns created under different mechanisms. References Cuxart, J., Yagüe, C., Morales, G., Terradellas, E., Orbe, J., Calvo, J., Fernández, A., Soler, M., Infante, C., Buenestado, P., Espinalt, Joergensen, H., Rees, J., Vilà, J., Redondo, J., Cantalapiedra, I. and Conangla, L.: Stable atmospheric boundary-layer experiment in Spain (Sables 98). A report, Boundary-Layer Meteorology, 96, 337-370, 2000. Dillon, T. M.: Vertical Overturns: A Comparison of Thorpe and Ozmidov Length Scales, J. Geophys. Res., 87(C12), 9601-9613, 1982. Itsweire, E. C.: Measurements of vertical overturns in stably stratified turbulent flow, Phys. Fluids, 27(4), 764-766, 1984. Kitade, Y., Matsuyama, M. and Yoshida, J.: Distribution of overturn induced by internal
Salmon, Philip S; Zeidler, Anita
2013-10-07
The structure of several network-forming liquids and glasses is considered, where a focus is placed on the detailed information that is made available by using the method of neutron diffraction with isotope substitution (NDIS). In the case of binary network glass-forming materials with the MX2 stoichiometry (e.g. GeO2, GeSe2, ZnCl2), two different length scales at distances greater than the nearest-neighbour distance manifest themselves by peaks in the measured diffraction patterns. The network properties are influenced by a competition between the ordering on these "intermediate" and "extended" length scales, which can be manipulated by changing the chemical identity of the atomic constituents or by varying state parameters such as the temperature and pressure. The extended-range ordering, which describes the decay of the pair-correlation functions at large-r, can be represented by making a pole analysis of the Ornstein-Zernike equations, an approach that can also be used to describe the large-r behaviour of the pair-correlation functions for liquid and amorphous metals where packing constraints are important. The first applications are then described of the NDIS method to measure the detailed structure of aerodynamically-levitated laser-heated droplets of "fragile" glass-forming liquid oxides (CaAl2O4 and CaSiO3) at high-temperatures (~2000 K) and the structure of a "strong" network-forming glass (GeO2) under pressures ranging from ambient to ~8 GPa. The high-temperature experiments show structural changes on multiple length scales when the oxides are vitrified. The high-pressure experiment offers insight into the density-driven mechanisms of network collapse in GeO2 glass, and parallels are drawn with the high-pressure behaviour of silica glass. Finally, the hydrogen-bonded network of water is considered, where the first application of the method of oxygen NDIS is used to measure the structures of light versus heavy water and a difference of approximately equal
Freunberger, S. A.
2007-07-01
This dissertation is concerned with the development, experimental diagnostics and mathematical modelling and simulation of polymer electrolyte fuel cells (PEFC). The central themes throughout this thesis are the closely interlinked phenomena of mass and charge transfer. In the face of developing a PEFC system for vehicle propulsion these phenomena are scrutinized on a broad range of relevant scales. Starting from the material related level of the membrane and the gas diffusion layer (GDL) we turn to length scales, where structural features of the cell additionally come into play. These are the scale of flow channels and ribs, the single cell and the cell stack followed by the cell, stack, and system development for an automotive power train. In Chapter 3 selected fundamental material models and properties, respectively, are explored that are crucial for the mathematical modelling and simulation of PEFC, as needed in some succeeding parts of this work. First, established mathematical models for mass and charge transfer in the membrane are compared within the framework of the membrane electrode assembly (MEA), which represents the electrochemical unit. Second, reliable values for effective diffusivities in the GDLs which are vital for the simulation of gaseous mass transport are measured. Therefore, a method is developed that allows measuring this quantity both as a function of compression and direction as this is a prerequisite of sophisticated more-dimensional numerical PEFC-models. Besides the cross section of the catalyst layer (CL) mass transfer under channels and ribs is considered as a major source of losses in particular under high load operation. As up to now there have been solely non-validated theoretical investigations, in Chapter 4 an experimental method is developed that is for the first time capable of resolving the current density distribution on the this scale. For this, the electron conductors in the cell are considered as 2-dimensional shunt
S M Yusuf
2004-07-01
We have investigated magnetic correlations in various CMR manganites on macroscopic, mesoscopic and microscopic length scales by carrying out DC magnetization, neutron depolarization, and neutron diffraction measurements. We present here the effect of substituting Mn with Fe and La with Dy in the ferromagnetic La0.7- CaMnO3 ( ∼ 0.3 - 0.33) compounds. Neutron diffraction has been used in order to characterize the long-range magnetic order and its gradual suppression by the substitution. Neutron depolarization study has been carried out in order to bridge the gap in our understanding regarding the nature of magnetic correlation obtained from the macroscopic and microscopic measurements. In particular, our study on La0.67Ca0.33Mn0.9Fe0.1O3 has established the fact that a true double exchange mediated spin-glass is insulating. In another study of La-site ionic size effect and its disorder in (La1-Dy)0.7Ca0.3MnO3, we have investigated the evolution of the length scale of magnetic ordering with a possible microscopic explanation and the results have been compared with that for the light rare earth substituted compounds.
Cosmic string loop distribution on all length scales and at any redshift
Lorenz, Larissa; Ringeval, Christophe [Institute of Mathematics and Physics, Centre for Cosmology, Particle Physics and Phenomenology, Louvain University, 2 Chemin du Cyclotron, 1348 Louvain-la-Neuve (Belgium); Sakellariadou, Mairi, E-mail: larissa.lorenz@uclouvain.be, E-mail: christophe.ringeval@uclouvain.be, E-mail: mairi.sakellariadou@kcl.ac.uk [Department of Physics, King' s College, University of London, Strand, London WC2R 2LS (United Kingdom)
2010-10-01
We analytically derive the expected number density distribution of Nambu-Goto cosmic string loops at any redshift soon after the time of string formation to today. Our approach is based on the Polchinski-Rocha model of loop formation from long strings which we adjust to fit numerical simulations and complement by a phenomenological modelling of gravitational backreaction. Cosmological evolution drives the loop distribution towards scaling on all length scales in both the radiation and matter era. Memory of any reasonable initial loop distribution in the radiation era is shown to be erased well before Big Bang Nucleosynthesis. In the matter era, the loop distribution reaches full scaling, up to some residual loops from the radiation era which may be present for extremely low string tension. Finally, the number density of loops below the gravitational cutoff is shown to be scale independent, proportional to a negative power of the string tension and insensitive to the details of the backreaction modelling. As an application, we show that the energy density parameter of loops today cannot exceed 10{sup −5} for currently allowed string tension values, while the loop number density cannot be less than 10{sup −6} per Mpc{sup 3}. Our result should provide a more robust basis for studying the cosmological consequences of cosmic string loops.
Length measurement in absolute scale via low-dispersion optical cavity
Pravdova, Lenka; Lesundak, Adam; Smid, Radek; Hrabina, Jan; Rerucha, Simon; Cip, Ondrej
2016-12-01
We report on the length measuring instrument with the absolute scale that was based on the combination of an optical frequency comb and a passive optical cavity. The time spacing of short femtosecond pulses, generated by the optical frequency comb, is optically phase locked onto the cavity free spectral range with a derivative spectroscopy technique so that the value of the repetition frequency of the femtosecond laser is tied to and determines the measured displacement. The instantaneous value of the femtosecond pulse train frequency is counted by a frequency counter. This counted value corresponds to the length given by the spacing between the two mirrors of the passive cavity. The phase lock between the femtosecond pulsed beam and the passive cavity is possible due to the low-dispersion of the cavity mirrors, where the silver coating on the mirrors was used to provide the low dispersion for the broadband radiation of the comb. Every reflection on the output mirror feeds a portion of the beam back to the cavity so that the output beam is a result of multiple interfering components. The parameters of the output beam are given not only by the parameters of the mirrors but mainly by the absolute distance between the mirror surfaces. Thus, one cavity mirror can be considered as the reference starting point of the distance to be measured and the other mirror is the measuring probe surveying the unknown distance. The measuring mirror of the experimental setup of the low-dispersion cavity is mounted on a piezoelectric actuator which provides small changes in the cavity length we used to test the length measurement method. For the verification of the measurement accuracy a reference incremental interferometer was integrated into our system so that the displacement of the piezoelectric actuator could be obtained with both measuring methods simultaneously.
A simulation procedure for light-matter interaction at different length scales
Leiner, Claude; Nemitz, Wolfgang; Wenzl, Franz P.; Hartmann, Paul; Hohenester, Ulrich; Sommer, Christian
2012-06-01
The development of photonic devices with tailor-made optical properties requires the control and the manipulation of light propagation within structures of different length scales, ranging from sub-wavelength to macroscopic dimensions. However, optical simulation at different length scales necessitates the combination of different simulation methods, which have to account properly for various effects such as polarization, interference, or diffraction: At dimensions much larger than the wavelength of light common ray-tracing (RT) techniques are conveniently employed, while in the subwavelength regime more sophisticated approaches, like the so-called finite-difference time-domain (FDTD) technique, are needed. Describing light propagation both in the sub-wavelength regime as well as at macroscopic length scales can only be achieved by bridging between these two approaches. In this contribution we present on the one hand a study aiming at the determination of the intermediate size range for which both simulation methods are applicable and on the other hand an approach for combining classical ray-tracing with FDTD simulation in order to handle optical elements of large sizes. Generally, the interface between RT and FDTD is restricted to very small sample areas. Nevertheless, many real world optical devices use e.g. diffractive optical elements (DOEs) having comparably large areas in the order of 1-2 mm² (or larger). Therefore, one has to develop strategies in order to handle the data transfer between FDTD and RT also for structures of such larger size scales. Our approach in this regard is based on the symmetries of the structures. In this way support programs like e.g. MATLAB can be used to replicate the near-field of a single structure and to merge it to the near-field of a larger area. Comparisons of RT and FDTD simulations in the far-field can be used to validate the physical correctness of this approach. With such procedure it is possible to optimize light
St. Martin, Clara M.; Lundquist, Julie K.; Handschy, Mark A.
2015-04-01
The variability in wind-generated electricity complicates the integration of this electricity into the electrical grid. This challenge steepens as the percentage of renewably-generated electricity on the grid grows, but variability can be reduced by exploiting geographic diversity: correlations between wind farms decrease as the separation between wind farms increases. But how far is far enough to reduce variability? Grid management requires balancing production on various timescales, and so consideration of correlations reflective of those timescales can guide the appropriate spatial scales of geographic diversity grid integration. To answer ‘how far is far enough,’ we investigate the universal behavior of geographic diversity by exploring wind-speed correlations using three extensive datasets spanning continents, durations and time resolution. First, one year of five-minute wind power generation data from 29 wind farms span 1270 km across Southeastern Australia (Australian Energy Market Operator). Second, 45 years of hourly 10 m wind-speeds from 117 stations span 5000 km across Canada (National Climate Data Archive of Environment Canada). Finally, four years of five-minute wind-speeds from 14 meteorological towers span 350 km of the Northwestern US (Bonneville Power Administration). After removing diurnal cycles and seasonal trends from all datasets, we investigate dependence of correlation length on time scale by digitally high-pass filtering the data on 0.25-2000 h timescales and calculating correlations between sites for each high-pass filter cut-off. Correlations fall to zero with increasing station separation distance, but the characteristic correlation length varies with the high-pass filter applied: the higher the cut-off frequency, the smaller the station separation required to achieve de-correlation. Remarkable similarities between these three datasets reveal behavior that, if universal, could be particularly useful for grid management. For high
Statistical theory and transition in multiple-scale-lengths turbulence in plasmas
Itoh, Sanae-I. [Research Institute for Applied Mechanics, Kyushu Univ., Kasuga, Fukuoka (Japan); Itoh, Kimitaka [National Inst. for Fusion Science, Toki, Gifu (Japan)
2001-06-01
The statistical theory of strong turbulence in inhomogeneous plasmas is developed for the cases where fluctuations with different scale-lengths coexist. Nonlinear interactions in the same kind of fluctuations as well as nonlinear interplay between different classes of fluctuations are kept in the analysis. Nonlinear interactions are modelled as turbulent drag, nonlinear noise and nonlinear drive, and a set of Langevin equations is formulated. With the help of an Ansatz of a large number of degrees of freedom with positive Lyapunov number, Langevin equations are solved and the fluctuation dissipation theorem in the presence of strong plasma turbulence has been derived. A case where two driving mechanisms (one for micro mode and the other for semi-micro mode) coexist is investigated. It is found that there are several states of fluctuations: in one state, the micro mode is excited and the semi-micro mode is quenched; in the other state, the semi-micro mode is excited, and the micro mode remains at finite but suppressed level. New type of turbulence transition is obtained, and a cusp type catastrophe is revealed. A phase diagram is drawn for turbulence which is composed of multiple classes of fluctuations. Influence of the inhomogeneous global radial electric field is discussed. A new insight is given for the physics of internal transport barrier. Finally, the nonlocal heat transport due to the long-wave-length fluctuations, which are noise-pumped by shorter-wave-length ones, is analyzed and the impact on transient transport problems is discussed. (author)
Local transport measurements at mesoscopic length scales using scanning tunneling potentiometry.
Wang, Weigang; Munakata, Ko; Rozler, Michael; Beasley, Malcolm R
2013-06-07
Under mesoscopic conditions, the transport potential on a thin film carrying a current is theoretically expected to bear spatial variation due to quantum interference. Scanning tunneling potentiometry is the ideal tool to investigate such variation, by virtue of its high spatial resolution. We report in this Letter the first detailed measurement of transport potential under mesoscopic conditions. Epitaxial graphene at a temperature of 17 K was chosen as the initial system for study because the characteristic transport length scales in this material are relatively large. Tip jumping artifacts are a major possible contribution to systematic errors; and we mitigate such problems by using custom-made slender and sharp tips manufactured by focused ion beam. In our data, we observe residual resistivity dipoles associated with topographical defects, and local peaks and dips in the potential that are not associated with topographical defects.
Kelley, Shana O.; Mirkin, Chad A.; Walt, David R.; Ismagilov, Rustem F.; Toner, Mehmet; Sargent, Edward H.
2014-12-01
Rapid progress in identifying disease biomarkers has increased the importance of creating high-performance detection technologies. Over the last decade, the design of many detection platforms has focused on either the nano or micro length scale. Here, we review recent strategies that combine nano- and microscale materials and devices to produce large improvements in detection sensitivity, speed and accuracy, allowing previously undetectable biomarkers to be identified in clinical samples. Microsensors that incorporate nanoscale features can now rapidly detect disease-related nucleic acids expressed in patient samples. New microdevices that separate large clinical samples into nanocompartments allow precise quantitation of analytes, and microfluidic systems that utilize nanoscale binding events can detect rare cancer cells in the bloodstream more accurately than before. These advances will lead to faster and more reliable clinical diagnostic devices.
Improved Estimates of the Milky Way's Disk Scale Length From Hierarchical Bayesian Techniques
Licquia, Timothy C
2016-01-01
The exponential scale length ($L_d$) of the Milky Way's (MW's) disk is a critical parameter for describing the global physical size of our Galaxy, important both for interpreting other Galactic measurements and helping us to understand how our Galaxy fits into extragalactic contexts. Unfortunately, current estimates span a wide range of values and often are statistically incompatible with one another. Here, we aim to determine an improved, aggregate estimate for $L_d$ by utilizing a hierarchical Bayesian (HB) meta-analysis technique that accounts for the possibility that any one measurement has not properly accounted for all statistical or systematic errors. Within this machinery we explore a variety of ways of modeling the nature of problematic measurements, and then use a Bayesian model averaging technique to derive net posterior distributions that incorporate any model-selection uncertainty. Our meta-analysis combines 29 different (15 visible and 14 infrared) photometric measurements of $L_d$ available in ...
Sánchez, A; Domínguez-Adame, F; Angel Sanchez; Francisco Dominguez-Adame
1994-01-01
We have examined the dynamical behavior of the kink solutions of the one-dimensional sine-Gordon equation in the presence of a spatially periodic parametric perturbation. Our study clarifies and extends the currently available knowledge on this and related nonlinear problems in four directions. First, we present the results of a numerical simulation program which are not compatible with the existence of a radiative threshold, predicted by earlier calculations. Second, we carry out a perturbative calculation which helps interpret those previous predictions, enabling us to understand in depth our numerical results. Third, we apply the collective coordinate formalism to this system and demonstrate numerically that it accurately reproduces the observed kink dynamics. Fourth, we report on a novel occurrence of length scale competition in this system and show how it can be understood by means of linear stability analysis. Finally, we conclude by summarizing the general physical framework that arises from our study.
Cellular adaptation to biomechanical stress across length scales in tissue homeostasis and disease.
Gilbert, Penney M; Weaver, Valerie M
2016-09-15
Human tissues are remarkably adaptable and robust, harboring the collective ability to detect and respond to external stresses while maintaining tissue integrity. Following injury, many tissues have the capacity to repair the damage - and restore form and function - by deploying cellular and molecular mechanisms reminiscent of developmental programs. Indeed, it is increasingly clear that cancer and chronic conditions that develop with age arise as a result of cells and tissues re-implementing and deregulating a selection of developmental programs. Therefore, understanding the fundamental molecular mechanisms that drive cell and tissue responses is a necessity when designing therapies to treat human conditions. Extracellular matrix stiffness synergizes with chemical cues to drive single cell and collective cell behavior in culture and acts to establish and maintain tissue homeostasis in the body. This review will highlight recent advances that elucidate the impact of matrix mechanics on cell behavior and fate across these length scales during times of homeostasis and in disease states.
The effects of geometry and length scale on nanomechanical properties in constrained systems
Jungk, John Michael
2005-07-01
The determination of mechanical properties in nanoscale geometries is becoming increasingly important as microsystem and integrated circuit technologies continue to mature. Many devices produced by these technologies are composed of materials with critical sample dimensions smaller than 100 nm. In microelectronics, this can be the thickness of a metallization or dielectric layer, while wear coatings on MEMS devices are frequently thinner than this length scale. Since structures of this type are susceptible to plasticity and fracture as a result of either contact or residual stresses, it is critical that the mechanical behavior of the individual components be well described. This thesis is directed at the development of methods for characterizing the mechanical properties in small volume systems. Using instrumented indentation techniques, typically called nanoindentation, a systematic study of the mechanical response of materials ranging from ductile metals to brittle ceramics was executed. More specifically, investigations into how single length scale approaches may be used to describe mechanical properties such as indentation hardening, ductile film delamination and strain energy release rates were performed. In addition, the acoustic energy released during the fracture of brittle ceramics was related to both stress intensity and a strain energy release rate. Finite element simulations of nanoindentation tests were performed using ABAQUS, a commercially available material modeling software program. These simulations were used to separate individual film and substrate responses from the experimentally observed film/substrate composite mechanical behavior. Finally, quasi-tribological experiments were performed to probe for transitions in friction or wear response as the local deformation varied from the nanoscale to the macroscale.
Babcock, E.
2015-12-01
The best environmental education equips people with the know-how and drive to create healthy communities and a healthy planet. While there are many wonderful organizations providing environmental learning, ensuring quality, cultural relevance and equity of access remains an elusive goal--especially if environmental education organizations work in isolation. Organizations across 12 counties in the Bay Area have come together to create a different model. They have founded ChangeScale, a regional collaborative dedicated to providing high quality environmental education to hundreds of thousands of youth---by working together. ChangeScale's work involves setting up school district-level partnerships, providing technical assistance to local environmental education networks, and training environmental educators across the region. In this talk, the presenter, who is a founding member and steering committee chair for ChangeScale, will outline the challenges of working at a regional scale with dozens of organizations. She will share the processes ChangeScale has used to develop a business plan and build membership. She will conclude by sharing the short term and long term potential impacts of working collectively for environmental literacy in the Bay Area.
Groundwater in the Earth's critical zone: Relevance to large-scale patterns and processes
Fan, Ying
2015-05-01
Although we have an intuitive understanding of the behavior and functions of groundwater in the Earth's critical zone at the scales of a column (atmosphere-plant-soil-bedrock), along a toposequence (ridge to valley), and across a small catchment (up to third-order streams), this paper attempts to assess the relevance of groundwater to understanding large-scale patterns and processes such as represented in global climate and Earth system models. Through observation syntheses and conceptual models, evidence are presented that groundwater influence is globally prevalent, it forms an environmental gradient not fully captured by the climate, and it can profoundly shape critical zone evolution at continental to global scales. Four examples are used to illustrate these ideas: (1) groundwater as a water source for plants in rainless periods, (2) water table depth as a driver of plant rooting depth, (3) the accessibility of groundwater as an ecological niche separator, and (4) groundwater as the lower boundary of land drainage and a global driver of wetlands. The implications to understanding past and future global environmental change are briefly discussed, as well as critical discipline, scale, and data gaps that must be bridged in order for us to translate what we learn in the field at column, hillslope and catchment scales, to what we must predict at regional, continental, and global scales.
Zebrafish brain mapping--standardized spaces, length scales, and the power of N and n.
Hunter, Paul R; Hendry, Aenea C; Lowe, Andrew S
2015-06-01
Mapping anatomical and functional parameters of the zebrafish brain is moving apace. Research communities undertaking such studies are becoming ever larger and more diverse. The unique features, tools, and technologies associated with zebrafish are propelling them as the 21st century model organism for brain mapping. Uniquely positioned as a vertebrate model system, the zebrafish enables imaging of anatomy and function at different length scales from intraneuronal compartments to sparsely distributed whole brain patterns. With a variety of diverse and established statistical modeling and analytic methods available from the wider brain mapping communities, the richness of zebrafish neuroimaging data is being realized. The statistical power of population observations (N) within and across many samples (n) projected onto a standardized space will provide vast databases for data-driven biological approaches. This article reviews key brain mapping initiatives at different levels of scale that highlight the potential of zebrafish brain mapping. By way of introduction to the next wave of brain mappers, an accessible introduction to the key concepts and caveats associated with neuroimaging are outlined and discussed.
Scrape-off Layer Flows With Pressure Gradient Scale Length ~ {rho}{sub p}
Robert J. Goldston
2013-03-08
A heuristic model for the plasma scrape-off width balances magnetic drifts against parallel loss at c{sub s} /2, resulting in a SOL width ~ {rho}{sub p}. T{sub sep} is calculated from Spitzer–Härm parallel thermal conduction. This results in a prediction for the power scrape-off width in quantitative agreement both in magnitude and scaling with recent experimental data. To achieve the ~ c{sub s} /2 flow assumed in this model and measured experimentally sets requirements on the ratio of upstream to total SOL particle sources, relative to the square-root of the ratio of target to upstream temperature. The Pfisch-Schlüter model for equilibrium flows has been modified to allow near-sonic flows, appropriate for gradient scale lengths of order {rho}{sub p}, resulting in a new quadrupole radial flow pattern. The strong parallel flows and plasma charging implied by this model suggest a mechanism for H-mode transition, consistent with many observations
Scrape-off layer flows with pressure gradient scale length ∼ρ{sub p}
Goldston, Robert J., E-mail: rgoldston@pppl.gov [Princeton Plasma Physics Laboratory, MS-41, Princeton, NJ 08543 (United States)
2013-07-15
A heuristic model for the plasma scrape-off width balances magnetic drifts against parallel loss at c{sub s}/2, resulting in a SOL width ∼ρ{sub p}. T{sub sep} is calculated from Spitzer–Härm parallel thermal conduction. This results in a prediction for the power scrape-off width in quantitative agreement both in magnitude and scaling with recent experimental data. To achieve the ∼c{sub s}/2 flow assumed in this model and measured experimentally sets requirements on the ratio of upstream to total SOL particle sources, relative to the square-root of the ratio of target to upstream temperature. The Pfisch–Schlüter model for equilibrium flows has been modified to allow near-sonic flows, appropriate for gradient scale lengths of order ρ{sub p}, resulting in a new quadrupole radial flow pattern. The strong parallel flows and plasma charging implied by this model suggest a mechanism for H-mode transition, consistent with many observations.
Turbulent boundary layer over roughness transition with variation in spanwise roughness length scale
Westerweel, Jerry; Tomas, Jasper; Eisma, Jerke; Pourquie, Mathieu; Elsinga, Gerrit; Jonker, Harm
2016-11-01
Both large-eddy simulations (LES) and water-tunnel experiments, using simultaneous stereoscopic PIV and LIF were done to investigate pollutant dispersion in a region where the surface changes from rural to urban roughness. This consists of rectangular obstacles where we vary the spanwise aspect ratio of the obstacles. A line source of passive tracer was placed upstream of the roughness transition. The objectives of the study are: (i) to determine the influence of the aspect ratio on the roughness-transition flow, and (ii) to determine the dominant mechanisms of pollutant removal from street canyons in the transition region. It is found that for a spanwise aspect ratio of 2 the drag induced by the roughness is largest of all considered cases, which is caused by a large-scale secondary flow. In the roughness transition the vertical advective pollutant flux is the main ventilation mechanism in the first three streets. Furthermore, by means of linear stochastic estimation the mean flow structure is identied that is responsible for exchange of the fluid between the roughness obstacles and the outer part of the boundary layer. Furthermore, it is found that the vertical length scale of this structure increases with increasing aspect ratio of the obstacles in the roughness region.
A phenomenological description of BslA assemblies across multiple length scales.
Morris, Ryan J; Bromley, Keith M; Stanley-Wall, Nicola; MacPhee, Cait E
2016-07-28
Intrinsically interfacially active proteins have garnered considerable interest recently owing to their potential use in a range of materials applications. Notably, the fungal hydrophobins are known to form robust and well-organized surface layers with high mechanical strength. Recently, it was shown that the bacterial biofilm protein BslA also forms highly elastic surface layers at interfaces. Here we describe several self-assembled structures formed by BslA, both at interfaces and in bulk solution, over a range of length scales spanning from nanometres to millimetres. First, we observe transiently stable and highly elongated air bubbles formed in agitated BslA samples. We study their behaviour in a range of solution conditions and hypothesize that their dissipation is a consequence of the slow adsorption kinetics of BslA to an air-water interface. Second, we describe elongated tubules formed by BslA interfacial films when shear stresses are applied in both a Langmuir trough and a rheometer. These structures bear a striking resemblance, although much larger in scale, to the elongated air bubbles formed during agitation. Taken together, this knowledge will better inform the conditions and applications of how BslA can be used in the stabilization of multi-phase materials.This article is part of the themed issue 'Soft interfacial materials: from fundamentals to formulation'.
Thevis, Mario; Thomas, Andreas; Geyer, Hans; Schänzer, Wilhelm
2014-12-01
Since Goldspink and colleagues identified the expression of the mRNA of an insulin-like growth factor 1 (IGF-1) isoform in response to mechanical stress in 1996, substantial research into the so-called mechano growth factor and its modus operandi followed until today. Promising preclinical results were obtained by using the synthetic, 24-amino acid residues spanning peptide translated from the exons 4-6 of IGF-1Ec (which was later referred to as the mechano growth factor (MGF) peptide), particularly with regard to increased muscle myoblast proliferation. Consequently, the MGF peptide represented a promising drug candidate for the treatment of neuromuscular disorders; however, its misuse potential in sport was also identified shortly thereafter, and the substance (or class of substances) has been considered prohibited according to the regulations of the World Anti-Doping Agency (WADA) since 2005. While various MGF peptide versions have been known to sports drug testing authorities, the occurrence of a 'full-length MGF' as offered via illicit channels to athletes or athletes' managers was reported in 2014, arguably being undetectable in doping controls. An aliquot of the product was obtained and the content characterized by state-of-the-art analytical approaches including gel electrophoretic and mass spectrometric (top-down and bottom-up) sequencing approaches. Upon full characterization, its implementation into modified routine doping controls using ultrafiltration, immunoaffinity-based isolation, and nanoliquid chromatography-high resolution/high accuracy mass spectrometry was established. A protein with a monoisotopic molecular mass of 12264.9 Da and a sequence closely related to IGF-1Ec (lacking the signal- and propeptide moiety) was identified. The C-terminus was found to be modified by the elimination of the terminal lysine and a R109H substitution. With the knowledge of the compound's composition, existing doping control assays targeting peptide hormones such
Pokhrel, A.; El Hannach, M.; Orfino, F. P.; Dutta, M.; Kjeang, E.
2016-10-01
X-ray computed tomography (XCT), a non-destructive technique, is proposed for three-dimensional, multi-length scale characterization of complex failure modes in fuel cell electrodes. Comparative tomography data sets are acquired for a conditioned beginning of life (BOL) and a degraded end of life (EOL) membrane electrode assembly subjected to cathode degradation by voltage cycling. Micro length scale analysis shows a five-fold increase in crack size and 57% thickness reduction in the EOL cathode catalyst layer, indicating widespread action of carbon corrosion. Complementary nano length scale analysis shows a significant reduction in porosity, increased pore size, and dramatically reduced effective diffusivity within the remaining porous structure of the catalyst layer at EOL. Collapsing of the structure is evident from the combination of thinning and reduced porosity, as uniquely determined by the multi-length scale approach. Additionally, a novel image processing based technique developed for nano scale segregation of pore, ionomer, and Pt/C dominated voxels shows an increase in ionomer volume fraction, Pt/C agglomerates, and severe carbon corrosion at the catalyst layer/membrane interface at EOL. In summary, XCT based multi-length scale analysis enables detailed information needed for comprehensive understanding of the complex failure modes observed in fuel cell electrodes.
Espinosa-Paredes, Gilberto, E-mail: gepe@xanum.uam.m [Area de Ingenieria en Recursos Energeticos, Universidad Autonoma Metropolitana-Iztapalapa, Av. San Rafael Atlixco 186, Col. Vicentina, Apartado Postal 55-535, Mexico D.F. 09340 (Mexico)
2010-05-15
The aim of this paper is to propose a framework to obtain a new formulation for multiphase flow conservation equations without length-scale restrictions, based on the non-local form of the averaged volume conservation equations. The simplification of the local averaging volume of the conservation equations to obtain practical equations is subject to the following length-scale restrictions: d << l << L, where d is the characteristic length of the dispersed phases, l is the characteristic length of the averaging volume, and L is the characteristic length of the physical system. If the foregoing inequality does not hold, or if the scale of the problem of interest is of the order of l, the averaging technique and therefore, the macroscopic theories of multiphase flow should be modified in order to include appropriate considerations and terms in the corresponding equations. In these cases the local form of the averaged volume conservation equations are not appropriate to describe the multiphase system. As an example of the conservation equations without length-scale restrictions, the natural circulation boiling water reactor was consider to study the non-local effects on the thermal-hydraulic core performance during steady-state and transient behaviors, and the results were compared with the classic local averaging volume conservation equations.
Short length scale mantle heterogeneity beneath Iceland probed by glacial modulation of melting
Sims, Kenneth W. W.; Maclennan, John; Blichert-Toft, Janne; Mervine, Evelyn M.; Blusztajn, Jurek; Grönvold, Karl
2013-10-01
Glacial modulation of melting beneath Iceland provides a unique opportunity to better understand both the nature and length scale of mantle heterogeneity. At the end of the last glacial period, ∼13 000 yr BP, eruption rates were ∼20-100 times greater than in glacial or late postglacial times and geophysical modeling posits that rapid melting of the large ice sheet covering Iceland caused a transient increase in mantle decompression melting rates. Here we present the first time-series of Sr-Nd-Hf-Pb isotopic data for a full glacial cycle from a spatially confined region of basaltic volcanism in northern Iceland. Basalts and picrites erupted during the early postglacial burst of volcanic activity are systematically offset to more depleted isotopic compositions than those of lavas erupted during glacial or recent (Iceland is heterogeneous on small (glacial unloading indicates that the isotopic composition of mantle heterogeneities can be linked to their melting behavior. The present geochemical data can be accounted for by a melting model in which a lithologically heterogeneous mantle source contains an enriched component more fusible than its companion depleted component.
A Test Of Newtonian Gravity At The 25 Micron Length Scale
Smullin, S J
2005-01-01
Several recent predictions of extra dimensions and exotic particles include Yukawa-type modifications to the classical Newtonian gravitational potential at length scales and magnitudes that may be accessible in tabletop experiments. To test these theories of physics beyond the Standard Model, we have built a probe to measure forces as small as 10−18 N between masses separated by distances on the order of 25 microns. The force sensor is a micromachined silicon cantilever. A gold test mass approximately (50 x 50 x 30) μm3 in size is glued to the end of the cantilever. An alternating pattern of gold and silicon bars is oscillated below the test mass; the coupling between the test mass and the varying gravitational field of the moving drive mass excites the cantilever on resonance. A fiber interferometer measures the cantilever motion and from this measurement, the force between the masses is deduced. The experiment is run at low temperatures in vacuum to reduce the thermal noise of the cantileve...
Tricot, G; Saitoh, A; Takebe, H
2015-11-28
The structure of tin borophosphate glasses, considered for the development of low temperature sealing glasses or anode materials for Li-batteries, has been analysed at the intermediate length scale by a combination of high field standard and advanced 1D/2D nuclear magnetic resonance techniques. The nature and extent of B/P mixing were analysed using the (11)B((31)P) dipolar heteronuclear multiple quantum coherence NMR sequence and the data interpretation allowed (i) detecting the presence and analysing the nature of the B-O-P linkages, (ii) re-interpreting the 1D (31)P spectra and (iii) extracting the proportion of P connected to borate species. Interaction between the different borate species was analysed using the (11)B double quantum-simple quantum experiment to (i) investigate the presence and nature of the B-O-B linkage, (ii) assign the different borate species observed all along the composition line and (iii) monitor the borate network formation. In addition, (119)Sn static NMR was used to investigate the evolution of the chemical environment of the tin polyhedra. Altogether, the set of data allowed determining the structural units constituting the glass network and quantifying the extent of B/P mixing. The structural data were then used to explain the non-linear and unusual evolution of the glass transition temperature.
The role of reactant unmixedness, strain rate, and length scale on premixed combustor performance
Samuelsen, S.; LaRue, J.; Vilayanur, S. [Univ. of California, Irvine, CA (United States)] [and others
1995-10-01
Lean premixed combustion provides a means to reduce pollutant formation and increase combustion efficiency. However, fuel-air mixing is rarely uniform in space and time. This nonuniformity in concentration will lead to relative increases in pollutant formation and decreases in combustion efficiency. The nonuniformity of the concentration at the exit of the premixer has been defined by Lyons (1981) as the {open_quotes}unmixedness.{close_quotes} Although turbulence properties such as length scales and strain rate are known to effect unmixedness, the exact relationship is unknown. Evaluating this relationship and the effect of unmixedness in premixed combustion on pollutant formation and combustion efficiency are an important part of the overall goal of US Department of Energy`s Advanced Turbine Systems (ATS) program and are among the goals of the program described herein. The information obtained from ATS is intended to help to develop and commercialize gas turbines which have (1) a wide range of operation/stability, (2) a minimal amount of pollutant formation, and (3) high combustion efficiency. Specifically, with regard to pollutants, the goals are to reduce the NO{sub x} emissions by at least 10%, obtain less than 20 PPM of both CO and UHC, and increase the combustion efficiency by 5%.
Neby, Simon; Sobolowski, Stefan
2017-04-01
How can users and stakeholders be actively involved with providing input to and using output from local-scale climate projections? How can the scientific community better understand the needs of local actors? And how should communication and cooperation efforts be organized? These are critical questions we aim to answer in a climate services project funded by the Norwegian Research Council (R3: Relevant, Reliable and Robust local-scale climate projections for Norway). The project takes into consideration not only the scientific issues in establishing useful local-scale climate projections, but also addresses the "usability gap" between climate information and decision-making. The lack of effective communication between scientists and user communities often result in outputs and products that are not matched with decision-relevant climate information. In the R3 project, the scientific participants actively engage with a range of users that have quite different information needs: municipalities, infrastructure developers, agriculture, energy producers, insurance companies, and more. In this particular presentation, we present our experiences concerning three specific issues that relate to the stakeholder-science interface: 1) Preferences are not clear-cut and pre-defined. In practice, this means that stakeholders often do not have precise information about their needs, nor precise information about how, where and whether their needs can be voiced. Similarly, science communities tend to presuppose that stakeholders are interested and have well-articulated needs, which is hardly the case. Collectively, that means that there is a need for an approach that guides the articulation and prioritization of preferences in a manner that integrates both scientific and stakeholder perspectives and takes the integrity of both perspectives seriously. 2) Technologies are unclear. Although information may be produced and used, past experiences, trial and error processes and pragmatic
Fu Suhua
2013-09-01
Full Text Available The slope length factor is one of the parameters of the Universal Soil Loss Equation (USLE and the Revised Universal Soil Loss Equation (RUSLE and is sometimes calculated based on a digital elevation model (DEM. The methods for calculating the slope length factor are important because the values obtained may depend on the methods used for calculation. The purpose of this study was to compare the difference in spatial distribution of the slope length factor between the different methods at a watershed scale. One method used the uniform slope length factor equation (USLFE where the effects of slope irregularities (such as slope gradient, etc. on soil erosion by water were not considered. The other method used segmented slope length factor equation(SSLFE which considered the effects of slope irregularities on soil erosion by water. The Arc Macro Language (AML Version 4 program for the revised universal soil loss equation(RUSLE.which uses the USLFE, was chosen to calculate the slope length factor. In a parallel analysis, the AML code of RUSLE Version 4 was modified according to the SSLFE to calculate the slope length factor. Two watersheds with different slope and gully densities were chosen. The results show that the slope length factor and soil loss using the USLFE method were lower than those using the SSLFE method, especially on downslopes watershed with more frequent steep slopes and higher gully densities. In addition, the slope length factor and soil loss calculated by the USLFE showed less spatial variation.
Quantum electrodynamics and the electron self-energy in a deformed space with a minimal length scale
Silva, Apollo V; Neves, M J
2016-01-01
The main motivation to study models in the presence of a minimal length is to obtain a quantum field theory free of the divergences. In this way, in this paper, we have constructed a new framework for quantum electrodynamics embedded in a minimal length scale background. New operators are introduced and the Green function method was used for the solution of the field equations, i.e., the Maxwell, Klein-Gordon and Dirac equations. We have analyzed specifically the scalar field and its one loop propagator. The mass of the scalar field regularized by the minimal length was obtained. The QED Lagrangian containing a minimal length was also constructed and the divergences were analyzed. The electron and photon propagators, and the electron self-energy at one loop as a function of the minimal length was also obtained.
Yang, Shujiang; Kertesz, Miklos
2006-12-01
The two bond length alternation related backbone carbon-carbon stretching Raman active normal modes of polyacetylene are notoriously difficulty to predict theoretically. We apply our new linear/exponential scaled quantum mechanical force field scheme to tackle this problem by exponentially adjusting the decay of the coupling force constants between backbone stretchings based on their distance which extends over many neighbors. With transferable scaling parameters optimized by least squares fitting to the experimental vibrational frequencies of short oligoenes, the scaled frequencies of trans-polyacetylene and its isotopic analogs agree very well with experiments. The linear/exponential scaling scheme is also applicable to the cis-polyacetylene case.
Role of length scales on microwave thawing dynamics in 2D cylinders
Basak, T.; Ayappa, K.G. [Indian Institute of Science, Bangalore (India). Department of Chemical Engineering
2002-11-01
Microwave (MW) thawing of 2D frozen cylinders exposed to uniform plane waves from one face, is modeled using the effective heat capacity formulation with the MW power obtained from the electric field equations. Computations are illustrated for tylose (23% methyl cellulose gel) which melts over a range of temperatures giving rise to a mushy zone. Within the mushy region the dielectric properties are functions of the liquid volume fraction. The resulting coupled, time dependent non-linear equation are solved using the Galerkin finite element method with a fixed mesh. Our method efficiently captures the multiple connected thawed domains that arise due to the penetration of MWs in the sample. For a cylinder of diameter D, the two length scales that control the thawing dynamics are D/D{sub p}, and D/{lambda}{sub m}, where D{sub p} and {lambda}{sub m} are the penetration depth and wavelength of radiation in the sample respectively. For D/D{sub p}, D/{lambda}{sub m}<<1 power absorption is uniform and thawing occurs almost simultaneously across the sample (Regime I). For D/D{sub p}>>1 thawing is seen to occur from the incident face, since the power decays exponentially into the sample (Regime III). At intermediate values, 0.2
Newcomb, C.; Qafoku, N. P.; Grate, J. W.; Hufschmid, R.; Browning, N.; De Yoreo, J. J.
2015-12-01
With elevated levels of carbon dioxide in the atmosphere due to anthropogenic emissions and disruption to the carbon cycle, the effects of climate change are being accelerated. Approximately 80% of Earth's terrestrial organic carbon is stored in soil, and the residence time of this carbon can range from hours to millenia. Understanding the dynamics of this carbon pool in the carbon cycle is crucial to both predicting climate and sustaining ecosystem services. Soil organic carbon is known to be strongly associated with high surface area clay minerals. The nature of these interactions is not well understood primarily due to the heterogeneity of soil, as much of the current knowledge relies on experiments that take a top-down approach using bulk experimental measurements. Our work seeks to probe physical, chemical, and molecular-level interactions at the organic-mineral interface using a bottom-up approach that establishes a model system where complexity can be built in systematically. By performing in situ techniques such as dynamic force spectroscopy, a technique where organic molecules can be brought into contact with mineral surfaces in a controlled manner using an atomic force microscope, we demonstrate the ability to mechanistically probe the energy landscape of individual organic molecules with mineral surfaces. We demonstrate the ability to measure the binding energies of soil-inspired organic functional groups (including carboxylic acid, amine, methyl, and phosphate) with clay and mineral surfaces as a function of solution chemistry. This effort can provide researchers with both guiding principles about carbon dynamics at the sub-nanometer length scale and insights into early aggregation events, where organic-mineral interactions play a significant role.
Min Jae Song
Full Text Available A major hurdle to understanding and exploiting interactions between the stem cell and its environment is the lack of a tool for precise delivery of mechanical cues concomitant to observing sub-cellular adaptation of structure. These studies demonstrate the use of microscale particle image velocimetry (μ-PIV for in situ spatiotemporal mapping of flow fields around mesenchymal stem cells, i.e. murine embryonic multipotent cell line C3H10T1/2, at the subcellular length scale, providing a tool for real time observation and analysis of stem cell adaptation to the prevailing mechanical milieu. In the absence of cells, computational fluid dynamics (CFD predicts flow regimes within 12% of μ-PIV measures, achieving the technical specifications of the chamber and the flow rates necessary to deliver target shear stresses at a particular height from the base of the flow chamber. However, our μ-PIV studies show that the presence of cells per se as well as the density at which cells are seeded significantly influences local flow fields. Furthermore, for any given cell or cell seeding density, flow regimes vary significantly along the vertical profile of the cell. Hence, the mechanical milieu of the stem cell exposed to shape changing shear stresses, induced by fluid drag, varies with respect to proximity of surrounding cells as well as with respect to apical height. The current study addresses a previously unmet need to predict and observe both flow regimes as well as mechanoadaptation of cells in flow chambers designed to deliver precisely controlled mechanical signals to live cells. An understanding of interactions and adaptation in response to forces at the interface between the surface of the cell and its immediate local environment may be key for de novo engineering of functional tissues from stem cell templates as well as for unraveling the mechanisms underlying multiscale development, growth and adaptation of organisms.
Compositional variations at ultra-structure length scales in coral skeleton
Meibom, Anders; Cuif, Jean-Pierre; Houlbreque, Fanny; Mostefaoui, Smail; Dauphin, Yannicke; Meibom, Karin L.; Dunbar, Robert
2008-03-01
Distributions of Mg and Sr in the skeletons of a deep-sea coral ( Caryophyllia ambrosia) and a shallow-water, reef-building coral ( Pavona clavus) have been obtained with a spatial resolution of 150 nm, using the NanoSIMS ion microprobe at the Muséum National d'Histoire Naturelle in Paris. These trace element analyses focus on the two primary ultra-structural components in the skeleton: centers of calcification (COC) and fibrous aragonite. In fibrous aragonite, the trace element variations are typically on the order of 10% or more, on length scales on the order of 1-10 μm. Sr/Ca and Mg/Ca variations are not correlated. However, Mg/Ca variations in Pavona are strongly correlated with the layered organization of the skeleton. These data allow for a direct comparison of trace element variations in zooxanthellate and non-zooxanthellate corals. In both corals, all trace elements show variations far beyond what can be attributed to variations in the marine environment. Furthermore, the observed trace element variations in the fibrous (bulk) part of the skeletons are not related to the activity of zooxanthellae, but result from other biological activity in the coral organism. To a large degree, this biological forcing is independent of the ambient marine environment, which is essentially constant on the growth timescales considered here. Finally, we discuss the possible detection of a new high-Mg calcium carbonate phase, which appears to be present in both deep-sea and reef-building corals and is neither aragonite nor calcite.
Statistical theory and transition in multiple-scale-length turbulence in plasmas
Itoh, Sanae-I [Research Institute for Applied Mechanics, Kyushu University, Kasuga (Japan); Itoh, Kimitaka [National Institute for Fusion Science, Toki (Japan)
2001-08-01
The statistical theory of strong turbulence in inhomogeneous plasmas is developed for the cases where fluctuations with different scale lengths coexist. Nonlinear interactions in the same kind of fluctuations as well as nonlinear interplay between different classes of fluctuations are kept in the analysis. Nonlinear interactions are modelled as turbulent drag, nonlinear noise and nonlinear drive, and a set of Langevin equations is formulated. With the help of an Ansatz of a large number of degrees of freedom with positive Lyapunov number, Langevin equations are solved and the fluctuation dissipation theorem in the presence of strong plasma turbulence has been derived. A case where two driving mechanisms (one for the micro mode and the other for semi-micro mode) coexist is investigated. It is found that there are several states of fluctuations: in one state, the micro mode is excited and the semi-micro mode is quenched; in the other state, the semi-micro mode is excited, and the micro mode remains at finite but at a suppressed level. A new type of turbulence transition is obtained, and a cusp-type catastrophe is revealed. A phase diagram is drawn for turbulence which is composed of multiple classes of fluctuations. The influence of the inhomogeneous global radial electric field is discussed. A new insight is given for the physics of the internal transport barrier. Finally, the non-local heat transport due to the long-wavelength fluctuations, which are noise-pumped by shorter-wavelength fluctuations, is analysed and its impact on transient transport problems is discussed. (author)
Thornton, E. B.; MacMahan, J. H.; Reniers, A. J.; Ashley, W.
2012-12-01
Macro-scale turbulent coherent flow structures in a natural fast-flowing river were examined with a combination of a novel 2 MHz Acoustic Doppler Beam (ADB) and a Maximum Likelihood Estimator (MLE) to characterize the stream-wise horizontal length scales and persistence of coherent flow structures by measuring the frequency (f)- streamwise-wavenumber (k) energy density velocity spectrum, E(f,k ), for the first time in natural rivers. The ADB was deployed under a range of Froude numbers (0.1-0.6) at high Reynolds Numbers based on depth and velocity conditions within a gravel-bed reach of the Kootenai River, ID. The MLE employed on the ADB data increased our ability to describe river motions with relatively long (>10 m) length scales in ~1 m water depths. The E(f,k) fall along a ridge described by V=f/k, where V is the mean velocity over depth, verifying Taylor's hypothesis. New, consistent length scale measures are defined based on averaged wave lengths of the low frequency E(f,k) and coherence spectra. Energetic (~50% of the total spectral energy), low-frequency (f1 m/s, L were found to be significantly longer than their corresponding coherence lengths suggesting that the turbulent structures evolve rapidly under these conditions. This is attributed to the stretching and concomitant deformation of pre-existing macro-turbulent motions by the ubiquitous bathymetry-induced spatial flow accelerations present in a natural gravel-bed river.Mean motion lengths, Lm, (circles) and coherence lengths, Lc, (squares) as a function of the mean streamwise velocity at locations in Zones 1-4.
Gaedke, Achim
2009-01-21
In this thesis, the interplay between diffusion and relaxation effects in spatially selective NMR experiments at short length scales is explored. This is especially relevant in the context of both conventional and mechanically detected MRI at (sub)micron resolution in biological specimens. Recent results on selectively excited very thin slices showed an in-slice-magnetization recovery orders of magnitude faster than the longitudinal relaxation time T1. However, those experiments were run on fully relaxed samples while MRI and especially mechanically detected NMR experiments are typically run in a periodic fashion with repetition times far below T1. The main purpose of this work therefore was to extend the study of the interplay between diffusion and longitudinal relaxation to periodic excitations. In some way, this is inverse phenomenon to the DESIRE (Diffusive Enhancement of SIgnal and REsolution) approach, proposed 1992 by Lauterbur. Experiments on periodically excited thin slices were carried out at a dedicated static field gradient cryomagnet with magnetic field gradients up to 180 T/m. In order to obtain plane slices, an appropriate isosurface of the gradient magnet had to be identified. It was found at a field of 3.8 T with a gradient of 73 T/m. In this field, slices down to a thickness of 3.2 {mu}m could be excited. The detection of the NMR signal was done using FIDs instead of echoes as the excitation bandwidth of those thin slices is sufficiently small to observe FIDs which are usually considered to be elusive to detection in such strong static field gradients. A simulation toolbox based on the full Bloch-Torrey-equation was developed to describe the excitation and the formation of NMR signals under those unusual conditions as well as the interplay of diffusion and magnetization recovery. Both the experiments and the simulations indicate that diffusion effects lead to a strongly enhanced magnetization modulation signal also under periodic excitation
Liu, Huabing; Nogueira d'Eurydice, Marcel; Obruchkov, Sergei; Galvosas, Petrik
2014-09-01
Pore length scales and pore surface relaxivities of rock cores with different lithologies were studied on a 2MHz Rock Core Analyzer. To determine the pore length scales of the rock cores, the high eigenmodes of spin bearing molecules satisfying the diffusion equation were detected with optimized encoding periods in the presence of internal magnetic fields Bin. The results were confirmed using a 64MHz NMR system, which supports the feasibility of high eigenmode detection at fields as low as 2MHz. Furthermore, this methodology was combined with relaxometry measurements to a two-dimensional experiment, which provides correlation between pore length and relaxation time. This techniques also yields information on the surface relaxivity of the rock cores. The estimated surface relaxivities were then compared to the results using an independent NMR method.
AbouZeid, Khaled Mohamed [Virginia Commonwealth University, Department of Chemistry (United States); Mohamed, Mona Bakr [Cairo University, National Institute of Laser Enhanced Science (NILES) (Egypt); El-Shall, M. Samy, E-mail: mselshal@vcu.edu [Virginia Commonwealth University, Department of Chemistry (United States)
2016-01-15
This work introduces a series of molecular bridging bi-functional linkers to produce laterally self-assembled nanostructures of the Au–CdSe nanoflowers on different length scales ranging from 10 nm to 100 microns. Assembly of Au nanocrystals within amorphous CdSe rods is found in the early stages of the growth of the Au–CdSe nanoflowers. The Au–CdSe nanoflowers are formed through a one-pot low temperature (150 °C) process where CdSe clusters are adsorbed on the surface of the Au cores, and they then start to form multiple arms and branches resulting in flower-shaped hybrid nanostructures. More complex assembly at a micron length scale can be achieved by means of bi-functional capping agents with appropriate alkyl chain lengths, such as 1,12-diaminododecane.
Sørup, Hjalte Jomo Danielsen
Time series of precipitation are necessary for assessment of urban hydrological systems. In a changed climate this is challenging as climate model output is not directly comparable to observations at the scales relevant for urban hydrology. The focus of this PhD thesis is downscaling...... of precipitation to spatio-temporal scales used in urban hydrology. It investigates several observational data products and identifies relevant scales where climate change and precipitation can be assessed for urban use. Precipitation is modelled at different scales using different stochastic techniques. A weather...... generator is used to produce an artificial spatio-temporal precipitation product that can be used both directly in large scale urban hydrological modelling and for derivation of extreme precipitation statistics relevant for urban hydrology. It is discussed why precipitation time series from a changed...
Numerical evaluation of the phase-field model for brittle fracture with emphasis on the length scale
Zhang, Xue; Vignes, Chet; Sloan, Scott W.; Sheng, Daichao
2017-05-01
The phase-field model has been attracting considerable attention due to its capability of capturing complex crack propagations without mesh dependence. However, its validation studies have primarily focused on the ability to predict reasonable, sharply defined crack paths. Very limited works have so far been contributed to estimate its accuracy in predicting force responses, which is majorly attributed to the difficulty in the determination of the length scale. Indeed, accurate crack path simulation can be achieved by setting the length scale to be sufficiently small, whereas a very small length scale may lead to unrealistic force-displacement responses and overestimate critical structural loads. This paper aims to provide a critical numerical investigation of the accuracy of phase-field modelling of brittle fracture with special emphasis on a possible formula for the length scale estimation. Phase-field simulations of a number of classical fracture experiments for brittle fracture in concretes are performed with simulated results compared with experimental data qualitatively and quantitatively to achieve this goal. Furthermore, discussions are conducted with the aim to provide guidelines for the application of the phase-field model.
Tuning Piezo ion channels to detect molecular-scale movements relevant for fine touch.
Poole, Kate; Herget, Regina; Lapatsina, Liudmila; Ngo, Ha-Duong; Lewin, Gary R
2014-03-24
In sensory neurons, mechanotransduction is sensitive, fast and requires mechanosensitive ion channels. Here we develop a new method to directly monitor mechanotransduction at defined regions of the cell-substrate interface. We show that molecular-scale (~13 nm) displacements are sufficient to gate mechanosensitive currents in mouse touch receptors. Using neurons from knockout mice, we show that displacement thresholds increase by one order of magnitude in the absence of stomatin-like protein 3 (STOML3). Piezo1 is the founding member of a class of mammalian stretch-activated ion channels, and we show that STOML3, but not other stomatin-domain proteins, brings the activation threshold for Piezo1 and Piezo2 currents down to ~10 nm. Structure-function experiments localize the Piezo modulatory activity of STOML3 to the stomatin domain, and higher-order scaffolds are a prerequisite for function. STOML3 is the first potent modulator of Piezo channels that tunes the sensitivity of mechanically gated channels to detect molecular-scale stimuli relevant for fine touch.
Elizabeth Margaret Stovold
2017-06-01
Full Text Available A Review of: Hanneke, R., & O’Brien, K. K. (2016. Comparison of three web-scale discovery services for health sciences research. Journal of the Medical Library Association, 104(2, 109-117. http://dx.doi.org/10.3163/1536-5050.104.2.004 Abstract Objective – To compare the results of health sciences search queries in three web-scale discovery (WSD services for relevance, duplicate detection, and retrieval of MEDLINE content. Design – Comparative evaluation and bibliometric study. Setting – Six university libraries in the United States of America. Subjects – Three commercial WSD services: Primo, Summon, and EBSCO Discovery Service (EDS. Methods – The authors collected data at six universities, including their own. They tested each of the three WSDs at two data collection sites. However, since one of the sites was using a legacy version of Summon that was due to be upgraded, data collected for Summon at this site were considered obsolete and excluded from the analysis. The authors generated three questions for each of six major health disciplines, then designed simple keyword searches to mimic typical student search behaviours. They captured the first 20 results from each query run at each test site, to represent the first “page” of results, giving a total of 2,086 total search results. These were independently assessed for relevance to the topic. Authors resolved disagreements by discussion, and calculated a kappa inter-observer score. They retained duplicate records within the results so that the duplicate detection by the WSDs could be compared. They assessed MEDLINE coverage by the WSDs in several ways. Using precise strategies to generate a relevant set of articles, they conducted one search from each of the six disciplines in PubMed so that they could compare retrieval of MEDLINE content. These results were cross-checked against the first 20 results from the corresponding query in the WSDs. To aid investigation of overall
Taylor-plasticity-based analysis of length scale effects in void growth
Liu, Junxian
2014-09-25
We have studied the void growth problem by employing the Taylor-based strain gradient plasticity theories, from which we have chosen the following three, namely, the mechanism-based strain gradient (MSG) plasticity (Gao et al 1999 J. Mech. Phys. Solids 47 1239, Huang et al 2000 J. Mech. Phys. Solids 48 99-128), the Taylor-based nonlocal theory (TNT; 2001 Gao and Huang 2001 Int. J. Solids Struct. 38 2615) and the conventional theory of MSG (CMSG; Huang et al 2004 Int. J. Plast. 20 753). We have addressed the following three issues which occur when plastic deformation at the void surface is unconstrained. (1) Effects of elastic deformation. Elasticity is essential for cavitation instability. It is therefore important to guarantee that the gradient term entering the Taylor model is the effective plastic strain gradient instead of the total strain gradient. We propose a simple elastic-plastic decomposition method. When the void size approaches the minimum allowable initial void size related to the maximum allowable geometrically necessary dislocation density, overestimation of the flow stress due to the negligence of the elastic strain gradient is on the order of lεY/R0 near the void surface, where l, εY and R0 are, respectively, the intrinsic material length scale, the yield strain and the initial void radius. (2) MSG intrinsic inconsistency, which was initially mentioned in Gao et al (1999 J. Mech. Phys. Solids 47 1239) but has not been the topic of follow-up studies. We realize that MSG higher-order stress arises due to the linear-strain-field approximation within the mesoscale cell with a nonzero size, lε. Simple analysis shows that within an MSG mesoscale cell near the void surface, the difference between microscale and mesoscale strains is on the order of (lε/R0)2, indicating that when lε/R0 ∼ 1.0, the higher-order stress effect can make the MSG result considerably different from the TNT or CMSG results. (3) Critical condition for cavitation instability
Wellman, Tyler J; Winkler, Tilo; Costa, Eduardo L V; Musch, Guido; Harris, R Scott; Venegas, Jose G; Vidal Melo, Marcos F
2012-09-01
Heterogeneous, small-airway diameters and alveolar derecruitment in poorly aerated regions of normal lungs could produce ventilation heterogeneity at those anatomic levels. We modeled the washout kinetics of (13)NN with positron emission tomography to examine how specific ventilation (sV) heterogeneity at different length scales is influenced by lung aeration. Three groups of anesthetized, supine sheep were studied: high tidal volume (Vt; 18.4 ± 4.2 ml/kg) and zero end-expiratory pressure (ZEEP) (n = 6); low Vt (9.2 ± 1.0 ml/kg) and ZEEP (n = 6); and low Vt (8.2 ± 0.2 ml/kg) and positive end-expiratory pressure (PEEP; 19 ± 1 cmH(2)O) (n = 4). We quantified fractional gas content with transmission scans, and sV with emission scans of infused (13)NN-saline. Voxel (13)NN-washout curves were fit with one- or two-compartment models to estimate sV. Total heterogeneity, measured as SD[log(10)(sV)], was divided into length-scale ranges by measuring changes in variance of log(10)(sV), resulting from progressive filtering of sV images. High-Vt ZEEP showed higher sV heterogeneity at 36-mm (r = -0.72) length scales (P < 0.001). We conclude that sV heterogeneity at length scales <60 mm increases in poorly aerated regions of mechanically ventilated normal lungs, likely due to heterogeneous small-airway narrowing and alveolar derecruitment. PEEP reduces sV heterogeneity by maintaining lung expansion and airway patency at those small length scales.
Validation of the Spanish-language version of the Relevant Outcome Scale for Alzheimer's Disease.
Carnero Pardo, C; López Alcalde, S; Espinosa García, M; Sánchez Magro, I
2017-09-01
The Relevant Outcome Scale for Alzheimer's Disease (ROSA) is a useful tool for evaluating and monitoring dementia patients. This study aims to evaluate the validity and reliability of the Spanish version of ROSA. Spanish multicentre study involving 39 researchers and including 237 patients with Alzheimer disease (78 mild, 79 moderate, and 80 severe). The patients were tested with the following: Mini-Mental State Examination (MMSE), Fototest, Neuropsychiatric Inventory (NPI), Blessed dementia scale, and a Spanish-language version of ROSA. A subsample of 40 subjects was retested in the 14 days following the initial evaluation. The construct validity was evaluated with the Spearman correlation coefficient (r), internal consistency with Cronbach's alpha (alpha), and test-retest reliability with the intraclass correlation coefficient (ICC). ROSA requires 13.8±7.4minutes to administer and its results show a significant association with the clinical stage of AD (mild, 116.7±23.1; moderate, 92.9±19.8; and severe, 64.3±22.6), and with results on the MMSE (r=0.68), Fototest (r=0.63), NPI (r=0.53), and Blessed dementia scale (r=-0.80). ROSA shows high internal consistency (alpha=0.90) and excellent test-retest reliability (ICC0.97). The Spanish version of ROSA is a brief, valid, and reliable tool permitting overall evaluation of patients with dementia. Copyright © 2016 Sociedad Española de Neurología. Publicado por Elsevier España, S.L.U. All rights reserved.
Harti, Ralph P.; Strobl, Markus; Betz, Benedikt; Jefimovs, Konstantins; Kagias, Matias; Grünzweig, Christian
2017-01-01
Neutron imaging and scattering give data of significantly different nature and traditional methods leave a gap of accessible structure sizes at around 10 micrometers. Only in recent years overlap in the probed size ranges could be achieved by independent application of high resolution scattering and imaging methods, however without providing full structural information when microstructures vary on a macroscopic scale. In this study we show how quantitative neutron dark-field imaging with a novel experimental approach provides both sub-pixel resolution with respect to microscopic correlation lengths and imaging of macroscopic variations of the microstructure. Thus it provides combined information on multiple length scales. A dispersion of micrometer sized polystyrene colloids was chosen as a model system to study gravity induced crystallisation of microspheres on a macro scale, including the identification of ordered as well as unordered phases. Our results pave the way to study heterogeneous systems locally in a previously impossible manner. PMID:28303923
Brisard, S.
2012-01-30
Morphological quantification of the complex structure of hierarchical geomaterials is of great relevance for Earth science and environmental engineering, among others. To date, methods that quantify the 3D morphology on length scales ranging from a few tens of nanometers to several hun-dred nanometers have had limited success. We demonstrate, for the first time, that it is possible to go beyond visualization and to extract quantitative morphological information from X-ray images in the aforementioned length scales. As examples, two different hierarchical geomaterials exhibiting complex porous structures ranging from nanometer to macroscopic scale are studied: a flocculated clay water suspension and two hydrated cement pastes. We show that from a single projection image it is possible to perform a direct computation of the ultra-small angle-scattering spectra. The predictions matched very well the experimental data obtained by the best ultra-small angle-scattering experimental setups as observed for the cement paste. In this context, we demonstrate that the structure of flocculated clay suspension exhibit two well-distinct regimes of aggregation, a dense mass fractal aggregation at short distance and a more open structure at large distance, which can be generated by a 3D reaction limited cluster-cluster aggregation process. For the first time, a high-resolution 3D image of fibrillar cement paste cluster was obtained from limited angle nanotomography.
Gauzzi, A.; Jönsson-Åkerman, B. Johan; Clerc-Dubois, A.; Pavuna, D.
2000-09-01
Measurements of critical temperature Tc in superconducting YBa2Cu3O6.9 films with reduced long-range structural order show the validity of the empirical scaling relation ΔTc propto rc-2 between disorder-induced reduction of Tc and structural coherence length rc in the ab-plane. This result is quantitatively explained by the disorder-induced confinement of the charge carriers within each ordered domain of size rc. Our analysis of the data based on this picture enables us to precisely determine the Ginzburg-Landau superconducting coherence length in the ab-plane, ξab = 1.41 ± 0.04 nm.
Schultz, R.A.; Soliva, R.; Fossen, H.; Okubo, C.H.; Reeves, D.M.
2008-01-01
Displacement-length data from faults, joints, veins, igneous dikes, shear deformation bands, and compaction bands define two groups. The first group, having a power-law scaling relation with a slope of n = 1 and therefore a linear dependence of maximum displacement and discontinuity length (Dmax = ??L), comprises faults and shear (non-compactional or non-dilational) deformation bands. These shearing-mode structures, having shearing strains that predominate over volumetric strains across them, grow under conditions of constant driving stress, with the magnitude of near-tip stress on the same order as the rock's yield strength in shear. The second group, having a power-law scaling relation with a slope of n = 0.5 and therefore a dependence of maximum displacement on the square root of discontinuity length (Dmax = ??L0.5), comprises joints, veins, igneous dikes, cataclastic deformation bands, and compaction bands. These opening- and closing-mode structures grow under conditions of constant fracture toughness, implying significant amplification of near-tip stress within a zone of small-scale yielding at the discontinuity tip. Volumetric changes accommodated by grain fragmentation, and thus control of propagation by the rock's fracture toughness, are associated with scaling of predominantly dilational and compactional structures with an exponent of n = 0.5. ?? 2008 Elsevier Ltd.
Tomas, J. M.; Eisma, H. E.; Pourquie, M. J. B. M.; Elsinga, G. E.; Jonker, H. J. J.; Westerweel, J.
2017-01-01
Both large-eddy simulations (LES) and water-tunnel experiments, using simultaneous stereoscopic particle image velocimetry and laser-induced fluorescence, have been used to investigate pollutant dispersion mechanisms in regions where the surface changes from rural to urban roughness. The urban roughness was characterized by an array of rectangular obstacles in an in-line arrangement. The streamwise length scale of the roughness was kept constant, while the spanwise length scale was varied by varying the obstacle aspect ratio l / h between 1 and 8, where l is the spanwise dimension of the obstacles and h is the height of the obstacles. Additionally, the case of two-dimensional roughness (riblets) was considered in LES. A smooth-wall turbulent boundary layer of depth 10h was used as the approaching flow, and a line source of passive tracer was placed 2h upstream of the urban canopy. The experimental and numerical results show good agreement, while minor discrepancies are readily explained. It is found that for l/h=2 the drag induced by the urban canopy is largest of all considered cases, and is caused by a large-scale secondary flow. In addition, due to the roughness transition the vertical advective pollutant flux is the main ventilation mechanism in the first three streets. Furthermore, by means of linear stochastic estimation the mean flow structure is identified that is responsible for street-canyon ventilation for the sixth street and onwards. Moreover, it is shown that the vertical length scale of this structure increases with increasing aspect ratio of the obstacles in the canopy, while the streamwise length scale does not show a similar trend.
Klameth, F; Henritzi, P; Vogel, M
2014-04-14
We perform molecular dynamics simulations to study static and dynamic length scales in molecular supercooled liquids, in particular, water. For a determination of these scales, we use equilibrium configurations and pin appropriate subsets of molecules so as to obtain random matrices, cylindrical pores, and slit confinements. Static length scales ξ(s) are determined by analyzing overlap correlation functions for various fractions of pinned molecules or distances to the confining walls. For water in all confinements and for propylene oxide trimers in random geometry, a linear increase of ξ(s) with inverse temperature is found. Dynamic length scales ξ(d) are determined by analogous analysis of fraction-dependent or position-resolved correlation times of structural relaxation. While ξ(d) continuously grows upon cooling in the cylindrical and slit confinements, we find no evidence for a temperature dependence in random matrices, implying that molecular dynamics in parsed volumes is qualitatively different from that in bulk liquids. Finally, we study possible connections between the growth of the static and dynamic length scales and the slowdown of the structural relaxation of the supercooled bulk liquids. For water, we observe a linear relation between ln τ(α) and ξ(s)²/T in the whole accessible range down to the critical temperature of mode-coupling theory, T(c). In the weakly supercooled regime, the same relation holds also for ξ(d), as obtained from cylindrical and slit confinements, but deviations from this behavior are observed near T(c). The results are discussed in connection with random first-order theory and experimental studies of liquid dynamics in nanoscopic confinements and binary mixtures.
The scaling law of climate change and its relevance to assessing (palaeo)biological responses
Kiessling, Wolfgang; Eichenseer, Kilian
2014-05-01
interglacials, are not monotonic, but punctuated by short-term cooling intervals. The fossil record tells us that biodiversity responded dramatically to ancient intervals of climate warming. We can now see that the apparently slower rates of change in some mass extinctions (Permian-Triassic, Triassic-Jurassic) were greater than today when the scaling law is considered. This reassures us that studying deep time patterns of organismic response to climate change is a worthwhile endeavor that is relevant for predicting the future. References Burrows, M. T., Schoeman, D. S., Buckley, L. B., Moore, P., Poloczanska, E. S., Brander, K. M., Brown, C., Bruno, J. F., Duarte, C. M., Halpern, B. S., Holding, J., Kappel, C. V., Kiessling, W., O'Connor, M. I., Pandolfi, J. M., Parmesan, C., Schwing, F. B., Sydeman, W. J., and Richardson, A. J.: The pace of shifting climate in marine and terrestrial ecosystems, Science, 334, 652-655, 2011. Gingerich, P. D.: Quantification and comparison of evolutionary rates, American Journal of Science, 293A, 453-478, 1993. Sadler, P. M.: Sediment accumulation rates and the completeness of stratigraphic sections, Journal of Geology, 89, 569-584, 1981. Sun, Y., Joachimski, M. M., Wignall, P. B., Yan, C., Chen, Y., Jiang, H., Wang, L., and Lai, X.: Lethally hot temperatures during the Early Triassic greenhouse, Science, 338, 366-370, 2012.
Physics on the Smallest Scales: An Introduction to Minimal Length Phenomenology
Sprenger, Martin; Nicolini, Piero; Bleicher, Marcus
2012-01-01
Many modern theories which try to unify gravity with the Standard Model of particle physics, such as e.g. string theory, propose two key modifications to the commonly known physical theories: the existence of additional space dimensions; the existence of a minimal length distance or maximal resolution. While extra dimensions have received a wide…
Validating a Mentoring Relationship Quality Scale: Does Match Strength Predict Match Length?
Rhodes, Jean E.; Schwartz, Sarah E. O.; Willis, Margaret M.; Wu, Max B.
2017-01-01
Youth mentoring relationships have significant potential for promoting positive youth development. Nonetheless, the benefits derived from such relationships depend considerably on the length and quality of the bonds that are created between mentors and youth. Although some attention has been paid to youth's experience of relationship quality, few…
Digital Library ImageRetrieval usingScale Invariant Feature and Relevance Vector Machine
Hongtao Zhang
2014-10-01
Full Text Available With the advance of digital library, the digital content develops with rich information connotation. Traditional information retrieval methods based on external characteristic and text description are unable to sufficientlyreveal and express the substance and semantic relation of multimedia information, and unable to fully reveal and describe the representative characteristics of information. Because of the abundant connotation of image content and the people’s abstract subjectivity in studying image content, the visual feature of the image is difficult to be described by key words. Therefore, this method not always can meet people’s needs, and the study of digital library image retrieval technique based on content is important to both academic research and application. At present, image retrieval methods are mainly based on the text and content, etc. But these existing algorithms have shortages, such as large errors and slow speeds. Motivated by the above fact, we in this paper propose a new approach based on relevance vector machine (RVM. The proposed approach first extracts the patch-level scale invariant image feature (SIFT, and then constructs the global features for images. The image feature is then delivered into RVM for retrieval. We evaluate the proposed approach on Corel dataset. The experimental result shows that the proposed method in this text has high accuracy when retrieves images.
Improving the local relevance of large scale water demand predictions: the way forward
Bernhard, Jeroen; Reynaud, Arnaud; de Roo, Ad
2016-04-01
Securing adequate availability of fresh water is of vital importance for socio-economic development of present and future Europe. Due to strong heterogeneity in climate conditions, some regions receive an abundant supply of water, where other areas almost completely depend on limited river discharge from upstream catchments. Furthermore, water demand differs greatly between regions due to differences in population density and local presence of intensive water using industries and agriculture. This results in many situations all across Europe where competition between water users translates into relative scarcity and economic damage. Additionally it is expected that inter-related economic and demographic developments, as well as climate change are to only further increase the need for efficient management of our water resources in the future. Successful policy making for such complex problems requires a good understanding of the system and reliable forecasting of conditions. The extent and complexity of the water use system however, stands in high contrast with the poor state of available data and lack of reliable predictions for this multi-disciplinary topic. Although the matching of available water to its demand is a European-wide problem, the amount of data with pan-European coverage is limited and usually with a national resolution at best. This is hindering researchers and policy makers because it usually makes large scale water demand predictions little relevant due to the strong regional heterogenic nature of the problem. We present in our study a first attempt of European-wide water demand predictions based on consistent regional data and econometric methods for the household and industry sector. We gathered data on water consumption, water prices and other relevant variables at the highest spatial detail available from national statistical offices and other organizational bodies. This database provides the most detailed up to date picture of present water
Evaluation of a Two-Length Scale Turbulence Model with Experiments on Shock-Driven Turbulent Mixing
Carter, John; Gore, Rob; Ranjan, Devesh
2015-11-01
A new second moment turbulence model which uses separate transport and decay length scales is used to model the shock-driven instability. The ability of the model to capture the evolution of turbulence statistics and mixing is discussed. Evaluation is based on comparison to the Georgia Tech shock tube experiments. In the experiments a membraneless light-over-heavy interface is created. There is a long-wavelength perturbation which exists due to inclination of the entire shock tube. By limiting calculations to one dimension, there is not a geometric description of the incline, and the ability of the transport length scale alone to capture the effect of the long-wavelength perturbation is tested.
Jin Guanghu
2014-09-01
Full Text Available The length of ballistic target is one of the most important features for target recognition. It can be extracted from ISAR Images. Unlike from the optical image, the length extraction from ISAR image has two difficulties. The first one is that it is hard to get the actual position of scattering centres by the traditional target extraction method. The second one is that the ISAR image’s cross scale is not known because of the target’s complex rotation. Here we propose two methods to solve these problems. Firstly, we use clustering method to get scattering centers. Secondly we propose to get cross scale of the ISAR images by affine registration. Experiments verified that our approach is realisable and has good performance.Defence Science Journal, Vol. 64, No. 5, September 2014, pp.458-463, DOI:http://dx.doi.org/10.14429/dsj.64.5001
The scaling of the minimum sum of edge lengths in uniformly random trees
Esteban, Juan Luis; Gómez-Rodríguez, Carlos
2016-01-01
The minimum linear arrangement problem on a network consists of finding the minimum sum of edge lengths that can be achieved when the vertices are arranged linearly. Although there are algorithms to solve this problem on trees in polynomial time, they have remained theoretical and have not been implemented in practical contexts to our knowledge. Here we use one of those algorithms to investigate the growth of this sum as a function of the size of the tree in uniformly random trees. We show that this sum is bounded above by its value in a star tree. We also show that the mean edge length grows logarithmically in optimal linear arrangements, in stark contrast to the linear growth that is expected on optimal arrangements of star trees or on random linear arrangements.
The scaling of the minimum sum of edge lengths in uniformly random trees
Esteban, Juan Luis; Ferrer-i-Cancho, Ramon; Gómez-Rodríguez, Carlos
2016-06-01
The minimum linear arrangement problem on a network consists of finding the minimum sum of edge lengths that can be achieved when the vertices are arranged linearly. Although there are algorithms to solve this problem on trees in polynomial time, they have remained theoretical and have not been implemented in practical contexts to our knowledge. Here we use one of those algorithms to investigate the growth of this sum as a function of the size of the tree in uniformly random trees. We show that this sum is bounded above by its value in a star tree. We also show that the mean edge length grows logarithmically in optimal linear arrangements, in stark contrast to the linear growth that is expected on optimal arrangements of star trees or on random linear arrangements.
Krsko, Peter; McCann, Thomas E; Thach, Thu-Trang; Laabs, Tracy L; Geller, Herbert M; Libera, Matthew R
2009-02-01
We engineered surfaces that permit the adhesion and directed growth of neuronal cell processes but that prevent the adhesion of astrocytes. This effect was achieved based on the spatial distribution of sub-micron-sized cell-repulsive poly(ethylene glycol) [PEG] hydrogels patterned on an otherwise cell-adhesive substrate. Patterns were identified that promoted cellular responses ranging from complete non-attachment, selective attachment, and directed growth at both cellular and subcellular length scales. At the highest patterning density where the individual hydrogels almost overlapped, there was no cellular adhesion. As the spacing between individual hydrogels was increased, patterns were identified where neurites could grow on the adhesive surface between hydrogels while astrocytes were unable to adhere. Patterns such as lines or arrays were identified that could direct the growth of these subcellular neuronal processes. At higher hydrogel spacings, both neurons and astrocytes adhered and grew in a manner approaching that of unpatterned control surfaces. Patterned lines could once again direct growth at cellular length scales. Significantly, we have demonstrated that the patterning of sub-micron/nano scale cell-repulsive features at microscale lengths on an otherwise cell-adhesive surface can differently control the adhesion and growth of cells and cell processes based on the difference in their characteristic sizes. This concept could potentially be applied to an implantable nerve-guidance device that would selectively enable regrowing axons to bridge a spinal-cord injury without interference from the glial scar.
Nondriven Polymer Translocation Through a Nanopore:Scaling for Translocation Time with Chain Length
LI Hui; ZHANG Jing; LIU Hong; SUN Chia-chung
2011-01-01
We investigated the dynamics of the passage for a polymer chain through a nanopore in the absence of any external driving force with Weeks-Chandler-Andersen potential in two-dimensional simulations,in particular,focused our attention on the scaling law of the mean translocation time.We found that the effect of hydrodynamic interactions is the major factor in determining the scaling exponents with increasing pore size.The scaling close to N1+2v was observed when the hydrodynamic interactions were screened in the cases of small pore sizes,while the scaling close to N3v was obtained when the hydrodynamic interactions were present in the cases of large pore sizes.
Helmuth, Brian; Broitman, Bernardo R; Yamane, Lauren; Gilman, Sarah E; Mach, Katharine; Mislan, K A S; Denny, Mark W
2010-03-15
Predicting when, where and with what magnitude climate change is likely to affect the fitness, abundance and distribution of organisms and the functioning of ecosystems has emerged as a high priority for scientists and resource managers. However, even in cases where we have detailed knowledge of current species' range boundaries, we often do not understand what, if any, aspects of weather and climate act to set these limits. This shortcoming significantly curtails our capacity to predict potential future range shifts in response to climate change, especially since the factors that set range boundaries under those novel conditions may be different from those that set limits today. We quantitatively examine a nine-year time series of temperature records relevant to the body temperatures of intertidal mussels as measured using biomimetic sensors. Specifically, we explore how a 'climatology' of body temperatures, as opposed to long-term records of habitat-level parameters such as air and water temperatures, can be used to extrapolate meaningful spatial and temporal patterns of physiological stress. Using different metrics that correspond to various aspects of physiological stress (seasonal means, cumulative temperature and the return time of extremes) we show that these potential environmental stressors do not always occur in synchrony with one another. Our analysis also shows that patterns of animal temperature are not well correlated with simple, commonly used metrics such as air temperature. Detailed physiological studies can provide guidance to predicting the effects of global climate change on natural ecosystems but only if we concomitantly record, archive and model environmental signals at appropriate scales.
Javvaji, Brahmanandam; Raha, S.; Mahapatra, D. Roy
2017-02-01
Electromagnetic and thermo-mechanical forces play a major role in nanotube-based materials and devices. Under high-energy electron transport or high current densities, carbon nanotubes fail via sequential fracture. The failure sequence is governed by certain length scale and flow of current. We report a unified phenomenological model derived from molecular dynamic simulation data, which successfully captures the important physics of the complex failure process. Length-scale and strain rate-dependent defect nucleation, growth, and fracture in single-walled carbon nanotubes with diameters in the range of 0.47 to 2.03 nm and length which is about 6.17 to 26.45 nm are simulated. Nanotubes with long length and small diameter show brittle fracture, while those with short length and large diameter show transition from ductile to brittle fracture. In short nanotubes with small diameters, we observe several structural transitions like Stone-Wales defect initiation, its propagation to larger void nucleation, formation of multiple chains of atoms, conversion to monatomic chain of atoms, and finally complete fracture of the carbon nanotube. Hybridization state of carbon-carbon bonds near the end cap evolves, leading to the formation of monatomic chain in short nanotubes with small diameter. Transition from ductile to brittle fracture is also observed when strain rate exceeds a critical value. A generalized analytical model of failure is established, which correlates the defect energy during the formation of atomic chain with aspect ratio of the nanotube and strain rate. Variation in the mechanical properties such as elastic modulus, tensile strength, and fracture strain with the size and strain rate shows important implications in mitigating force fields and ways to enhance the life of electronic devices and nanomaterial conversion via fracture in manufacturing.
Predicting the roughness length of turbulent flows over landscapes with multi-scale microtopography
Pelletier, Jon D.; Field, Jason P.
2016-01-01
The fully rough form of the law of the wall is commonly used to quantify velocity profiles and associated bed shear stresses in fluvial, aeolian, and coastal environments. A key parameter in this law is the roughness length, z0. Here we propose a predictive formula for z0 that uses the amplitude and slope of each wavelength of microtopography within a discrete-Fourier-transform-based approach. Computational fluid dynamics (CFD) modeling is used to quantify the effective z0 valu...
Hill, Jon; Piggott, M. D.; Ham, David A.; Popova, E. E.; Srokosz, M. A.
2012-10-01
Research into the use of unstructured mesh methods for ocean modelling has been growing steadily in the last few years. One advantage of using unstructured meshes is that one can concentrate resolution where it is needed. In addition, dynamic adaptive mesh optimisation (DAMO) strategies allow resolution to be concentrated when this is required. Despite the advantage that DAMO gives in terms of improving the spatial resolution where and when required, small-scale turbulence in the oceans still requires parameterisation. A two-equation, generic length scale (GLS) turbulence model (one equation for turbulent kinetic energy and another for a generic turbulence length-scale quantity) adds this parameterisation and can be used in conjunction with adaptive mesh techniques. In this paper, an implementation of the GLS turbulence parameterisation is detailed in a non-hydrostatic, finite-element, unstructured mesh ocean model, Fluidity-ICOM. The implementation is validated by comparing to both a laboratory-scale experiment and real-world observations, on both fixed and adaptive meshes. The model performs well, matching laboratory and observed data, with resolution being adjusted as necessary by DAMO. Flexibility in the prognostic fields used to construct the error metric used in DAMO is required to ensure best performance. Moreover, the adaptive mesh models perform as well as fixed mesh models in terms of root mean square error to observation or theoretical mixed layer depths, but uses fewer elements and hence has a reduced computational cost.
Altmoos, Michael; Henle, Klaus
2010-11-01
Habitat models for animal species are important tools in conservation planning. We assessed the need to consider several scales in a case study for three amphibian and two grasshopper species in the post-mining landscapes near Leipzig (Germany). The two species groups were selected because habitat analyses for grasshoppers are usually conducted on one scale only whereas amphibians are thought to depend on more than one spatial scale. First, we analysed how the preference to single habitat variables changed across nested scales. Most environmental variables were only significant for a habitat model on one or two scales, with the smallest scale being particularly important. On larger scales, other variables became significant, which cannot be recognized on lower scales. Similar preferences across scales occurred in only 13 out of 79 cases and in 3 out of 79 cases the preference and avoidance for the same variable were even reversed among scales. Second, we developed habitat models by using a logistic regression on every scale and for all combinations of scales and analysed how the quality of habitat models changed with the scales considered. To achieve a sufficient accuracy of the habitat models with a minimum number of variables, at least two scales were required for all species except for Bufo viridis, for which a single scale, the microscale, was sufficient. Only for the European tree frog ( Hyla arborea), at least three scales were required. The results indicate that the quality of habitat models increases with the number of surveyed variables and with the number of scales, but costs increase too. Searching for simplifications in multi-scaled habitat models, we suggest that 2 or 3 scales should be a suitable trade-off, when attempting to define a suitable microscale.
Song, Jing; Tranchida, Davide; Vancso, G. Julius
2008-01-01
The Young’s modulus of cross-linked poly(dimethylsiloxane) (PDMS) surface was quantitatively investigated as a function of UV/ozone treatment time across different length scales. An AFM was used to probe PDMS surface mechanical properties at the nanometer length scale. The Young’s modulus of each sa
Szymanski, R.; Sosnowski, S.
2017-01-01
Computer simulations (Monte Carlo and numerical integration of differential equations) and theoretical analysis show that the statistical nature of polyaddition, both irreversible and reversible one, affects the way the macromolecules of different lengths are distributed among the small volume nano-reactors (droplets in this study) at any reaction time. The corresponding droplet distributions in respect to the number of reacting chains as well as the chain length distributions depend, for the given reaction time, on rate constants of polyaddition kp and depolymerization kd (reversible process), and the initial conditions: monomer concentration and the number of its molecules in a droplet. As a model reaction, a simple polyaddition process (M)1+(M)1 ⟶ ⟵ (M)2 , (M)i+(M)j ⟶ ⟵ (M)i+j was chosen, enabling to observe both kinetic and thermodynamic (apparent equilibrium constant) effects of a small number of reactant molecules in a droplet. The average rate constant of polymerization is lower than in a macroscopic system, depending on the average number of reactant molecules in a droplet. The apparent equilibrium constants of polymerization Ki j=[(M)i +j] ¯ /([(M)i] ¯ [(M)j] ¯ ) appear to depend on oligomer/polymer sizes as well as on the initial number of monomer molecules in a droplet. The corresponding equations, enabling prediction of the equilibrium conditions, were derived. All the analyzed effects are observed not only for ideally dispersed systems, i.e. with all droplets containing initially the same number of monomer (M)1 molecules, but also when initially the numbers of monomer molecules conform the Poisson distribution, expected for dispersions of reaction mixtures.
Azhar, Hussain
This study looks at polarization and its components’ sensitivity to assumptions about equivalence scales, income definition, ethical income distribution parameters, and the income accounting period. A representative sample of Danish individual incomes from 1984 to 2002 is utilised. Results show...... that polarization has increased over time, regardless of the applied measure, when the last part of the period is compared to the first part of the period. Primary causes being increased inequality (alienation) and faster income growth among high incomes relative to those in the middle of the distribution....... Increasing the accounting period confirms the reduction in inequality found for shorter periods, but polarization is virtually unchanged, because income group identification increases. Applying different equivalence scales does not change polarization ranking for different years, but identification ranks...
Hausdorff, Jeffrey M.
2009-06-01
Parkinson's disease (PD) is a common, debilitating neurodegenerative disease. Gait disturbances are a frequent cause of disability and impairment for patients with PD. This article provides a brief introduction to PD and describes the gait changes typically seen in patients with this disease. A major focus of this report is an update on the study of the fractal properties of gait in PD, the relationship between this feature of gait and stride length and gait variability, and the effects of different experimental conditions on these three gait properties. Implications of these findings are also briefly described. This update highlights the idea that while stride length, gait variability, and fractal scaling of gait are all impaired in PD, distinct mechanisms likely contribute to and are responsible for the regulation of these disparate gait properties.
Tong, Chenning; Li, Wei; Yuan, Mengyuan; Carter, Campbell
2016-11-01
We investigate three-scalar mixing in a turbulent coaxial jet, in which a center jet and an annular flow, consisting of acetone-doped air and ethylene respectively, are mixed with the co-flow air. We investigate the effects of the velocity and length scale ratios of the annular flow to the center jet. Planar laser-induced fluorescence and Rayleigh scattering are employed to image the scalars. The results show that the velocity ratio alters the relative mean shear rates in the mixing layers between the center jet and the annular flow and between the annular flow and the co-flow, modifying the scalar fields through mean-flow advection, turbulent transport, and small-scale mixing. The length scale ratio determines the degree of separation between the center jet and the co-flow. The results show that while varying the velocity ratio can alter the mixing characteristics qualitatively, varying the annulus width only has quantitative effects. The evolution of the mean scalar profiles are dominated by the mean-flow advection, while the shape of the joint probability density function is largely determined by the turbulent transport and molecular diffusion. The results in the present study have implications for understanding and modeling multiscalar mixing in turbulent reactive flows. Supported by NSF.
Toju, Hirokazu
2008-05-01
Although coevolutionary theory predicts that evolutionary interactions between species are spatially hierarchical, few studies have examined coevolutionary processes at multiple spatial scales. In an antagonistic system involving a plant, the Japanese camellia (Camellia japonica), and its obligate seed predator, the camellia weevil (Curculio camelliae), I elucidated the local adaptation of a camellia defensive armament (pericarp thickness) and a weevil offensive armament (rostrum length) within Yakushima Island (ca. 30 km in diameter), compared to a larger-scale variation in those traits throughout Japan reported in previous studies. Results showed that camellia pericarp thickness and weevil rostrum length vary remarkably within several kilometers on this island. In addition, geographic variation in each camellia and weevil armament was best explained by the armament size of the sympatric participant than by abiotic environmental heterogeneity. However, I also found that camellia pericarp thickness significantly decreased in cool-temperate (i.e., highland) areas, suggesting the contributions of climate on the spatial structuring of the weevil-camellia interaction. Interestingly, relatively thin pericarps occurred not only in the highlands but also in some low-altitude areas, indicating that other factors such as nonrandom or asymmetric gene flow play important roles in the metapopulation processes of interspecific interactions at small spatial scales.
Crawford, Emmett Dudley
This thesis describes investigations into the mechanical and thermal characteristics of amorphous polymeric materials by structural changes on the molecular and the microscopic scale. On the molecular scale, the structure of a cross-linked polymeric material is controlled by changes in the molecular weight between cross-links, cross-link functionality, and chain stiffness. With control of the network structure, an expansive range of mechanical and thermal characteristics is possible. These properties range from intrinsic properties, such as the glass transition temperature, to performance properties, such as impact behavior. Relationships between the network structure and measured properties are established by the use of a variety of theories from rubber elasticity to free volume. Relationships are also established between the various measured properties through solid and fracture mechanics. The introduction of soft rubbery particles on the microscopic scale into a glassy polymeric matrix is commonly employed to create a tougher material. Despite the prevalent use, the mechanisms and sequence of mechanisms of toughening are poorly understood. The mechanisms and sequence of mechanisms are elucidated in this investigation through the use of unique mechanical tests and materials with favorable properties. The unique mechanical tests in this investigation include tensile dilatometry and a multi-axial stress state test. The multi-axial stress state test, which allows independent control of the dilational and deviatoric stresses of a material between uniaxial compression and equal biaxial tension, consists of a uniaxially loaded and pressurized thin walled hollow cylinder. The materials include liquid rubber modified epoxies, voided epoxies, and core-shell rubber modified polyvinylchloride. The voided epoxy material separates the matrix contributions from those of the rubbery phase, while the core-shell rubber modified polyvinylchloride provides optical verification of
Rider, Alexander D; Blakemore, Charles P; Louis, Maxime; Lu, Marie; Gratta, Giorgio
2016-01-01
We present the results of a search for unknown interactions that couple to mass between an optically levitated microsphere and a gold-coated silicon cantilever. The scale and geometry of the apparatus enables a search for new forces that appear at distances below 100 $\\mu$m and which would have evaded previous searches due to screening mechanisms. The data are consistent with electrostatic backgrounds and place upper limits on the strength of new interactions at 5.6 \\times 10^4$ in the region of parameter space where the self-coupling $\\Lambda \\gtrsim 5$ meV and the microspheres are not fully screened.
Optimal smoothing length scale for actuator line models of lifting surfaces
Martinez-Tossas, Luis A
2015-01-01
The actuator line model (ALM) is a commonly used method to represent lifting surfaces such as wind turbine blades within Large-Eddy Simulations (LES). In ALM the lift and drag forces are replaced by an imposed body force which is typically smoothed over several grid points using a Gaussian kernel with some prescribed smoothing width $\\epsilon$. To date, the choice of $\\epsilon$ has most often been based on numerical considerations mostly related to the grid spacing used in LES. However, especially for finely resolved LES with grid spacings on the order or smaller than the chord-length of the blade, the best choice of $\\epsilon$ is not known. Focusing first on the lift force, here we find $\\epsilon$ and the force center location that minimize the square difference between the velocity fields obtained from solving 2D potential flow over Joukowski airfoils and solving the Euler equations including the imposed body force. The latter solution is found for the linearized problem, and is valid for small angles of at...
Patchiness of ion-exchanged mica revealed by DNA binding dynamics at short length scales
Billingsley, D. J.; Lee, A. J.; Johansson, N. A. B.; Walton, A.; Stanger, L.; Crampton, N.; Bonass, W. A.; Thomson, N. H.
2014-01-01
The binding of double-stranded (ds) DNA to mica can be controlled through ion-exchanging the mica with divalent cations. Measurements of the end-to-end distance of linear DNA molecules discriminate whether the binding mechanism occurs through 2D surface equilibration or kinetic trapping. A range of linear dsDNA fragments have been used to investigate length dependences of binding. Mica, ion-exchanged with Ni(II) usually gives rise to kinetically trapped DNA molecules, however, short linear fragments (ion-exchanged mica is heterogeneous, and contains patches or domains, separating different ionic species. These results correlate with imaging of dsDNA under aqueous buffer on Ni(II)-mica and indicate that binding domains are of the order of 100 nm in diameter. Shorter DNA fragments behave intermediate to the two extreme cases of 2D equilibration and kinetic trapping. Increasing the incubation time of Ni(II) on mica, from minutes to hours, brings the conformations of the shorter DNA fragments closer to the theoretical value for kinetic trapping, indicating that long timescale kinetics play a role in ion-exchange. X-ray photoelectron spectroscopy (XPS) was used to confirm that the relative abundance of Ni(II) ions on the mica surface increases with time. These findings can be used to enhance spatial control of binding of DNA to inorganic surfaces with a view to patterning high densities arrays.
Length-Displacement Scaling of Lunar Thrust Faults and the Formation of Uphill-Facing Scarps
Hiesinger, Harald; Roggon, Lars; Hetzel, Ralf; Clark, Jaclyn D.; Hampel, Andrea; van der Bogert, Carolyn H.
2017-04-01
Lobate scarps are straight to curvilinear positive-relief landforms that occur on all terrestrial bodies [e.g., 1-3]. They are the surface manifestation of thrust faults that cut through and offset the upper part of the crust. Fault scarps on planetary surfaces provide the opportunity to study the growth of faults under a wide range of environmental conditions (e.g., gravity, temperature, pore pressure) [4]. We studied four lunar thrust-fault scarps (Simpelius-1, Morozov (S1), Fowler, Racah X-1) ranging in length from 1.3 km to 15.4 km [5] and found that their maximum total displacements are linearly correlated with length over one order of magnitude. We propose that during the progressive accumulation of slip, lunar faults propagate laterally and increase in length. On the basis of our measurements, the ratio of maximum displacement, D, to fault length, L, ranges from 0.017 to 0.028 with a mean value of 0.023 (or 2.3%). This is an order of magnitude higher than the value of 0.1% derived by theoretical considerations [4], and about twice as large as the value of 0.012-0.013 estimated by [6,7]. Our results, in addition to recently published findings for other lunar scarps [2,8], indicate that the D/L ratios of lunar thrust faults are similar to those of faults on Mercury and Mars (e.g., 1, 9-11], and almost as high as the average D/L ratio of 3% for faults on Earth [16,23]. Three of the investigated thrust fault scarps (Simpelius-1, Morozov (S1), Fowler) are uphill-facing scarps generated by slip on faults that dip in the same direction as the local topography. Thrust faults with such a geometry are common ( 60% of 97 studied scarps) on the Moon [e.g., 2,5,7]. To test our hypothesis that the surface topography plays an important role in the formation of uphill-facing fault scarps by controlling the vertical load on a fault plane, we simulated thrust faulting and its relation to topography with two-dimensional finite-element models using the commercial code ABAQUS
Sapp, Kayla; Shlomovitz, Roie; Maibaum, Lutz
Biological membranes exhibit long-range spatial structure in both chemical composition and geometric shape, which gives rise to remarkable physical phenomena and important biological functions. Continuum models that describe these effects play an important role in our understanding of membrane biophysics at large length scales. We review the mathematical framework used to describe both composition and shape degrees of freedom, and present best practices to implement such models in a computer simulation. We discuss in detail two applications of continuum models of cell membranes: the formation of microemulsion and modulated phases, and the effect of membrane-mediated interactions on the assembly of membrane proteins.
Berezhkovskii, Alexander M.; Coppey, Mathieu; Sealfon, Stuart C.; Shvartsman, Stanislav
2008-06-01
A problem of cell-to-cell communication by diffusible ligands is analyzed for the case when cells are distributed in three dimensions and diffusible ligands are secreted by cells and reversibly bind to cell surface receptors. Following its binding to a receptor, the ligand can either dissociate and be released back in the medium or be absorbed by the cell in a process that is called internalization. Using an effective medium approximation, we derive analytical expressions that characterize the time and length scales associated with the ligand trajectories leading to internalization. We discuss the applicability of our approximation and illustrate the application of our results to a specific cellular system.
Yavuzkurt, Savash
1991-01-01
The main objective of this research is to address two important but unresolved problems: (1) the measurement of vertical and transverse length scales via space correlations for all Reynolds stress components and velocity-temperature correlations, both in the free stream and within the boundary layer using the existing triple and quad-wire probes; and (2) to relate the character of the free stream turbulence to the character of the turbulence within the boundary layer in order to determine the effect on surface heat transfer.
Lidorikis, Elefterios; Bachlechner, Martina E.; Kalia, Rajiv K.; Nakano, Aiichiro; Vashishta, Priya; Voyiadjis, George Z.
2001-08-20
A hybrid molecular-dynamics (MD) and finite-element simulation approach is used to study stress distributions in silicon/silicon-nitride nanopixels. The hybrid approach provides atomistic description near the interface and continuum description deep into the substrate, increasing the accessible length scales and greatly reducing the computational cost. The results of the hybrid simulation are in good agreement with full multimillion-atom MD simulations: atomic structures at the lattice-mismatched interface between amorphous silicon nitride and silicon induce inhomogeneous stress patterns in the substrate that cannot be reproduced by a continuum approach alone.
Wu, Wen-fei; Xie, Jing-xing; Gong, Zhi-jun; Li, Bao-wei [Inner Mongolia Univ. of Science and Technology, Baotou (China). Inner Mongolia Key Lab. for Utilization of Bayan Obo Multi-Metallic Resources: Elected State Key Lab.
2013-07-01
The process of the pulverized coal combustion in tangential firing boiler has prominent significance on improving boiler operation efficiency and reducing NO{sub X} emission. This paper aims at researching complex turbulent vortex coherent structure formed by the four corners jets in the burner zone, a cold experimental model of tangential firing boiler has been built. And by employing spatial correlation analysis method and PIV (Particle Image Velocimetry) technique, the law of Vortex scale distribution on the three typical horizontal layers of the model based on the turbulent Integral Length Scale (ILS) has been researched. According to the correlation analysis of ILS and the temporal average velocity, it can be seen that the turbulent vortex scale distribution in the burner zone of the model is affected by both jet velocity and the position of wind layers, and is not linear with the variation of jet velocity. The vortex scale distribution of the upper primary air is significantly different from the others. Therefore, studying the ILS of turbulent vortex integral scale is instructive to high efficiency cleaning combustion of pulverized coal in theory.
Pegoraro, Adrian F; Fredberg, Jeffrey J; Park, Jin-Ah
2016-04-10
As do all things in biology, cell mechanosensation, adhesion and migration begin at the scale of the molecule. Collections of molecules assemble to comprise microscale objects such as adhesions, organelles and cells. And collections of cells in turn assemble to comprise macroscale tissues. From the points of view of mechanism and causality, events at the molecular scale are seen most often as being the most upstream and, therefore, the most fundamental and the most important. In certain collective systems, by contrast, events at many scales of length conspire to make contributions of equal importance, and even interact directly and strongly across disparate scales. Here we highlight recent examples in cellular mechanosensing and collective cellular migration where physics at some scale bigger than the cell but smaller than the tissue - the mesoscale - becomes the missing link that is required to tie together findings that might otherwise seem counterintuitive or even unpredictable. These examples, taken together, establish that the phenotypes and the underlying physics of collective cellular migration are far richer than previously anticipated. Copyright © 2015 Elsevier Inc. All rights reserved.
Application of nonlocal models to nano beams. Part II: Thickness length scale effect.
Kim, Jun-Sik
2014-10-01
Applicability of nonlocal models to nano-beams is discussed in terms of the Eringen's nonlocal Euler-Bernoulli (EB) beam model. In literature, most work has taken the axial coordinate derivative in the Laplacian operator presented in nonlocal elasticity. This causes that the non-locality always makes the beam soften as compared to the local counterpart. In this paper, the thickness scale effect is solely considered to investigate if the nonlocal model can simulate stiffening effect. Taking the thickness derivative in the Laplacian operator leads to the presence of a surface stress state. The governing equation derived is compared to that of the EB model with the surface stress. The results obtained reveal that the nonlocality tends to decrease the bending moment stiffness whereas to increase the bending rigidity in the governing equation. This tendency also depends on the surface conditions.
Hirai, Kenji; Reboul, Julien; Morone, Nobuhiro; Heuser, John E; Furukawa, Shuhei; Kitagawa, Susumu
2014-10-22
Porous coordination polymers (PCPs) are an intriguing class of molecular-based materials because of the designability of framework scaffolds, pore sizes and pore surface functionalities. Besides the structural designability at the molecular scale, the structuring of PCPs into mesoscopic/macroscopic morphologies has attracted much attention due to the significance for the practical applications. The structuring of PCPs at the mesoscopic/macroscopic scale has been so far demonstrated by the spatial localization of coordination reactions on the surface of templates or at the phase boundaries. However, these methodologies have never been applied to the fabrication of solid-solution or multivariate metal-organic frameworks (MOFs), in which multiple components are homogeneously mixed. Herein, we demonstrate the structuring of a box-type superstructure comprising of a solid-solution PCP by integrating a bidirectional diffusion of multiple organic ligands into molecular assembly. The parent crystals of [Zn2(ndc)2(bpy)]n were placed in the DMF solution of additional organic component of H2bdc, and the temperature was rapidly elevated up to 80 °C (ndc = 1,4-naphthalenedicarboxylate, bpy = 4,4'-bipyridyl, bdc = 1,4-benzenedicarboxylate). The dissolution of the parent crystals induced the outward diffusion of components; contrariwise, the accumulation of the other organic ligand of H2bdc induced the inward diffusion toward the surface of the parent crystals. This bidirectional diffusion of multiple components spatially localized the recrystallization at the surface of cuboid parent crystals; therefore, the nanocrystals of a solid-solution PCP ([Zn2(bdc)1.5(ndc)0.5(bpy)]n) were organized into a mesoscopic box superstructure. Furthermore, we demonstrated that the box superstructures enhanced the mass transfer kinetics for the separation of hydrocarbons.
Pinheiro, L.; Furlan, A. P.; Krott, L. B.; Diehl, A.; Barbosa, M. C.
2017-02-01
Molecular Dynamic and Monte Carlo studies are performed in a system of particles interacting through core-softened (CS) potential, composed by two length scales: a repulsive shoulder at short distances and the another a variable scale, that can be repulsive or strongly attractive depending on the parameters used. The system show water-like anomalous behavior. The density, diffusion and structural anomalous regions in the pressure versus temperature phase diagram shrink in pressure as the system becomes more attractive. The transition appears with the increase of the attraction well. We found that the liquid-gas phase transition is Ising-like for all the CS potentials and its critical temperature increases with the increase of the attraction. No Ising-like behavior for the liquid-liquid phase transition was detected in the Monte Carlo simulations what might be due to the presence of stable amorphous phases.
Zeng Zheng-Zhong; Qiu Ai-Ci
2004-01-01
Numerical computation based on a zero-dimensional thin-plasma-shell model has been carried out to study the scaling of the maximum kinetic energy per unit length, the current amplitude and the compression ratio for the imploding Z-pinch liner driven by peaked current pulses. A dimensionless scaling constant of 0.9 with an error less than 10% is extracted at the optimal choice of the current and liner parameters. Deviation of the chosen experimental parameter from the optimal exerts a minor influence on the kinetic energy for wider-shaped and slower-decaying pulses, but the influence becomes significant for narrower-shaped and faster-decaying pulses. The computation is in reasonable agreement with experimental data from the Z, Saturn, Blackjack 5 and Qiangguang-I liners.
Alter, Orly; Golub, Gene H
2006-08-01
We describe the singular value decomposition (SVD) of yeast genome-scale mRNA lengths distribution data measured by DNA microarrays. SVD uncovers in the mRNA abundance levels data matrix of genes x arrays, i.e., electrophoretic gel migration lengths or mRNA lengths, mathematically unique decorrelated and decoupled "eigengenes." The eigengenes are the eigenvectors of the arrays x arrays correlation matrix, with the corresponding series of eigenvalues proportional to the series of the "fractions of eigen abundance." Each fraction of eigen abundance indicates the significance of the corresponding eigengene relative to all others. We show that the eigengenes fit "asymmetric Hermite functions," a generalization of the eigenfunctions of the quantum harmonic oscillator and the integral transform which kernel is a generalized coherent state. The fractions of eigen abundance fit a geometric series as do the eigenvalues of the integral transform which kernel is a generalized coherent state. The "asymmetric generalized coherent state" models the measured data, where the profiles of mRNA abundance levels of most genes as well as the distribution of the peaks of these profiles fit asymmetric Gaussians. We hypothesize that the asymmetry in the distribution of the peaks of the profiles is due to two competing evolutionary forces. We show that the asymmetry in the profiles of the genes might be due to a previously unknown asymmetry in the gel electrophoresis thermal broadening of a moving, rather than a stationary, band of RNA molecules.
Marte Gutierrez; Dong-Joon Youn
2015-01-01
Fracture systems have strong influence on the overall mechanical behavior of fractured rock masses due to their relatively lower stiffness and shear strength than those of the rock matrix. Understanding the effects of fracture geometrical distribution, such as length, spacing, persistence and orientation, is important for quantifying the mechanical behavior of fractured rock masses. The relation between fracture geometry and the mechanical characteristics of the fractured rock mass is complicated due to the fact that the fracture geometry and mechanical behaviors of fractured rock mass are strongly dependent on the length scale. In this paper, a comprehensive study was conducted to determine the effects of fracture distribution on the equivalent continuum elastic compliance of fractured rock masses over a wide range of fracture lengths. To account for the stochastic nature of fracture distributions, three different simulation techniques involving Oda’s elastic compliance tensor, Monte Carlo simulation (MCS), and suitable probability density functions (PDFs) were employed to represent the elastic compliance of fractured rock masses. To yield geologically realistic results, parameters for defining fracture distribu-tions were obtained from different geological fields. The influence of the key fracture parameters and their relations to the overall elastic behavior of the fractured rock mass were studied and discussed. A detailed study was also carried out to investigate the validity of the use of a representative element volume (REV) in the equivalent continuum representation of fractured rock masses. A criterion was also proposed to determine the appropriate REV given the fracture distribution of the rock mass.
Marte Gutierrez
2015-12-01
Full Text Available Fracture systems have strong influence on the overall mechanical behavior of fractured rock masses due to their relatively lower stiffness and shear strength than those of the rock matrix. Understanding the effects of fracture geometrical distribution, such as length, spacing, persistence and orientation, is important for quantifying the mechanical behavior of fractured rock masses. The relation between fracture geometry and the mechanical characteristics of the fractured rock mass is complicated due to the fact that the fracture geometry and mechanical behaviors of fractured rock mass are strongly dependent on the length scale. In this paper, a comprehensive study was conducted to determine the effects of fracture distribution on the equivalent continuum elastic compliance of fractured rock masses over a wide range of fracture lengths. To account for the stochastic nature of fracture distributions, three different simulation techniques involving Oda's elastic compliance tensor, Monte Carlo simulation (MCS, and suitable probability density functions (PDFs were employed to represent the elastic compliance of fractured rock masses. To yield geologically realistic results, parameters for defining fracture distributions were obtained from different geological fields. The influence of the key fracture parameters and their relations to the overall elastic behavior of the fractured rock mass were studied and discussed. A detailed study was also carried out to investigate the validity of the use of a representative element volume (REV in the equivalent continuum representation of fractured rock masses. A criterion was also proposed to determine the appropriate REV given the fracture distribution of the rock mass.
Carpentier, S. F. A.; Roy-Chowdhury, K.; Stephenson, R. A.; Stovba, S.
2009-10-01
A novel statistical analysis, which augments conventional interpretation of deep seismic reflection/refraction data, is applied to the DOBRE 2000/2001 reflection profile. The goal is to improve delineation of the lithosphere in terms of lithotectonic units and to compare these to existing interpretations. After a successful validation of the method using synthetic data, stochastic parameters estimated from windowed average lateral autocorrelations in the DOBRE data are compiled in a two-dimensional profile of von Karman-type causative reflectivity. These estimates in terms of lateral correlation lengths and power law exponents are accompanied by associated uncertainties. Given its low uncertainties, the lateral correlation length ax turns out to be a robust delineator. The profile of ax reveals systematic spatial variations in the lithospheric fabric below the Donbas Fold Belt. As in earlier interpretations based upon conventional processing of reflection/refraction data, both the sedimentary basin and Moho discontinuity stand out clearly, as well as a region indicating massive vertical intrusion in the crust from upper mantle sills and ultramafic underplating of the lower crust. Notable differences with conventional interpretations include the number and extent of supra-Moho rift pillow structures, the lack of imaging a crust-cutting dislocation feature and a laterally disturbed uppermost mantle. Von Karman lateral correlation length provides new independent information at a scale between velocity models from wide-angle reflection/refraction data and line drawings from near vertical reflections and provides new insights and understanding of lithospheric evolution.
On determining characteristic length scales in pressure-gradient turbulent boundary layers
Vinuesa, R.; Bobke, A.; Örlü, R.; Schlatter, P.
2016-05-01
In the present work, we analyze three commonly used methods to determine the edge of pressure gradient turbulent boundary layers: two based on composite profiles, the one by Chauhan et al. ["Criteria for assessing experiments in zero pressure gradient boundary layers," Fluid Dyn. Res. 41, 021404 (2009)] and the one by Nickels ["Inner scaling for wall-bounded flows subject to large pressure gradients," J. Fluid Mech. 521, 217-239 (2004)], and the other one based on the condition of vanishing mean velocity gradient. Additionally, a new method is introduced based on the diagnostic plot concept by Alfredsson et al. ["A new scaling for the streamwise turbulence intensity in wall-bounded turbulent flows and what it tells us about the `outer' peak," Phys. Fluids 23, 041702 (2011)]. The boundary layers developing over the suction and pressure sides of a NACA4412 wing section, extracted from a direct numerical simulation at chord Reynolds number Rec = 400 000, are used as the test case, besides other numerical and experimental data from favorable, zero, and adverse pressure-gradient flat-plate turbulent boundary layers. We find that all the methods produce robust results with mild or moderate pressure gradients, although the composite-profile techniques require data preparation, including initial estimations of fitting parameters and data truncation. Stronger pressure gradients (with a Rotta-Clauser pressure-gradient parameter β larger than around 7) lead to inconsistent results in all the techniques except the diagnostic plot. This method also has the advantage of providing an objective way of defining the point where the mean streamwise velocity is 99% of the edge velocity and shows consistent results in a wide range of pressure gradient conditions, as well as flow histories. Collapse of intermittency factors obtained from a wide range of pressure-gradient and Re conditions on the wing further highlights the robustness of the diagnostic plot method to determine the
Jeanmairet, Guillaume; Levesque, Maximilien; Borgis, Daniel
2013-10-21
We present an extension of our recently introduced molecular density functional theory of water [G. Jeanmairet et al., J. Phys. Chem. Lett. 4, 619 (2013)] to the solvation of hydrophobic solutes of various sizes, going from angstroms to nanometers. The theory is based on the quadratic expansion of the excess free energy in terms of two classical density fields: the particle density and the multipolar polarization density. Its implementation requires as input a molecular model of water and three measurable bulk properties, namely, the structure factor and the k-dependent longitudinal and transverse dielectric susceptibilities. The fine three-dimensional water structure around small hydrophobic molecules is found to be well reproduced. In contrast, the computed solvation free-energies appear overestimated and do not exhibit the correct qualitative behavior when the hydrophobic solute is grown in size. These shortcomings are corrected, in the spirit of the Lum-Chandler-Weeks theory, by complementing the functional with a truncated hard-sphere functional acting beyond quadratic order in density, and making the resulting functional compatible with the Van-der-Waals theory of liquid-vapor coexistence at long range. Compared to available molecular simulations, the approach yields reasonable solvation structure and free energy of hard or soft spheres of increasing size, with a correct qualitative transition from a volume-driven to a surface-driven regime at the nanometer scale.
On the coherence length of large-scale peculiar velocities and gravitational clustering
Kashlinsky, A. (National Radio Astronomy Observatory, Charlottesville, VA (USA); Queen Mary College, London (England))
1989-08-01
If the large-scale structure in the universe is formed by gravitational clustering of less than 0 density fluctuations, the correlation function of massive objects/clusters of the clustering hierarchy would be increased over the underlying mass autocorrelation function. This means that if light traces mass, the peculiar gravitational field on the average would be stronger when measured by galaxies associated with such clusters. This in turn would lead to larger rms peculiar velocities deduced from the motions of such samples. Ellipticals are known to populate preferentially dense regions/(rich) clusters, and it is, therefore, suggested that this mechanism is responsible for the large peculiar motions observed recently by the Seven Samurai in a sample of elliptical galaxies. On the assumption that light traces mass, these and the cluster-cluster correlation function results are consistent with gravitational clustering of n of about -1 fluctuations in Omega of about 0.2 universe. It is further shown that according to the gravitational clustering theory, galaxies selected preferentially from poor groups should exhibit small rms peculiar velocities. 21 refs.
Li, Calvin H.; Rioux, Russell P.
2016-01-01
Spherical Cu nanocavity surfaces are synthesized to examine the individual role of contact angles in connecting lateral Rayleigh-Taylor wavelength to vertical Kevin-Helmholtz wavelength on hydrodynamic instability for the onset of pool boiling Critical Heat Flux (CHF). Solid and porous Cu pillar surfaces are sintered to investigate the individual role of pillar structure pitch at millimeter scale, named as module wavelength, on hydrodynamic instability at CHF. Last, spherical Cu nanocavities are coated on the porous Cu pillars to create a multiscale Cu structure, which is studied to examine the collective role and relative significance of contact angles and module wavelength on hydrodynamic instability at CHF, and the results indicate that module wavelength plays the dominant role on hydrodynamic instability at CHF when the height of surface structures is equal or above ¼ Kelvin-Helmholtz wavelength. Pool boiling Heat Transfer Coefficient (HTC) enhancements on spherical Cu nanocavity surfaces, solid and porous Cu pillar surfaces, and the integrated multiscale structure have been investigated, too. The experimental results reveal that the nanostructures and porous pillar structures can be combined together to achieve even higher enhancement of HTC than that of individual structures. PMID:27841322
Li, Calvin H; Rioux, Russell P
2016-11-14
Spherical Cu nanocavity surfaces are synthesized to examine the individual role of contact angles in connecting lateral Rayleigh-Taylor wavelength to vertical Kevin-Helmholtz wavelength on hydrodynamic instability for the onset of pool boiling Critical Heat Flux (CHF). Solid and porous Cu pillar surfaces are sintered to investigate the individual role of pillar structure pitch at millimeter scale, named as module wavelength, on hydrodynamic instability at CHF. Last, spherical Cu nanocavities are coated on the porous Cu pillars to create a multiscale Cu structure, which is studied to examine the collective role and relative significance of contact angles and module wavelength on hydrodynamic instability at CHF, and the results indicate that module wavelength plays the dominant role on hydrodynamic instability at CHF when the height of surface structures is equal or above ¼ Kelvin-Helmholtz wavelength. Pool boiling Heat Transfer Coefficient (HTC) enhancements on spherical Cu nanocavity surfaces, solid and porous Cu pillar surfaces, and the integrated multiscale structure have been investigated, too. The experimental results reveal that the nanostructures and porous pillar structures can be combined together to achieve even higher enhancement of HTC than that of individual structures.
Eddy length scales and the Rossby radius in the Arctic Ocean
A. J. G. Nurser
2013-10-01
Full Text Available The first (and second baroclinic deformation (or Rossby radii are presented and discussed north of ~60° N, focusing on deep basins and shelf seas in the high Arctic Ocean, the Nordic Seas, Baffin Bay, Hudson Bay and the Canadian Arctic Archipelago, derived from high-resolution ice-ocean general circulation model output. Comparison of the model output with measured results shows that low values of the Rossby radius (in shallow water and high values (in the Canada Basin are accurately reproduced, while intermediate values (in the region of the Makarov and Amundsen Basins are overestimated. In the high Arctic Ocean, the first Rossby radius increases from ~5 km in the Nansen Basin to ~15 km in the central Canadian Basin. In the shelf seas and elsewhere, values are low (1–7 km, reflecting weak density stratification, shallow water, or both. Seasonality only strongly impacts the Rossby radii in shallow seas where winter homogenisation of the water column can reduce it to the order of 100 m. We also offer an interpretation and explanation of the observed scales of Arctic Ocean eddies.
Dominant length scale of the ``pure'' turbulent fluctuations in the outer region of wall turbulence
Kwon, Yong Seok; Monty, Jason; Hutchins, Nick
2014-11-01
A new method of decomposing the total velocity in boundary layers, which removes the influence of instantaneous boundary layer thickness variations to the fluctuating velocity component, is proposed. The recent proposition of the quiescent core of turbulent channel flow by Kwon et al. (J. Fluid Mech., 751, 228 (2014)) permits us to apply the same decomposition to channel flows where the quiescent core is analogous to the free-stream. Using this decomposition, it is observed that the majority of the large-scale streamwise velocity fluctuation within the intermittent region is attributed to the oscillation of the turbulent/non-turbulent interface or the quiescent core. It suggests that the quiescent core and the free-stream play a similar role and the flow nearer to the wall in both flows is more similar than previously thought while the different characteristics of the free-stream and the quiescent core account for the differences in the outer region of two flows. These findings re-affirm the analogy between the quiescent core and the free-stream, which could potentially lead to the unified conceptual model between internal and external flows. This work is financially supported by the Australian Research Council and the Defence Science and Technology Organisation.
Plasma-field Coupling at Small Length Scales in Solar Wind Near 1 AU
Livadiotis, G.; Desai, M. I.
2016-10-01
In collisionless plasmas such as the solar wind, the coupling between plasma constituents and the embedded magnetic field occurs on various temporal and spatial scales, and is primarily responsible for the transfer of energy between waves and particles. Recently, it was shown that the transfer of energy between solar wind plasma particles and waves is governed by a new and unique relationship: the ratio between the magnetosonic energy and the plasma frequency is constant, E ms/ω pl ˜ ℏ*. This paper examines the variability and substantial departure of this ratio from ℏ* observed at ˜1 au, which is caused by a dispersion of fast magnetosonic (FMS) waves. In contrast to the efficiently transferred energy in the fast solar wind, the lower efficiency of the slow solar wind can be caused by this dispersion, whose relation and characteristics are derived and studied. In summary, we show that (i) the ratio E ms/ω pl transitions continuously from the slow to the fast solar wind, tending toward the constant ℏ* (ii) the transition is more efficient for larger thermal, Alfvén, or FMS speeds; (iii) the fast solar wind is almost dispersionless, characterized by quasi-constant values of the FMS speed, while the slow wind is subject to dispersion that is less effective for larger wind or magnetosonic speeds; and (iv) the constant ℏ* is estimated with the best known precision, ℏ* ≈ (1.160 ± 0.083) × 10-22 Js.
Namekata, Kosuke; Watanabe, Kyoko; Asai, Ayumi; Shibata, Kazunari
2016-01-01
Shibata & Yokoyama (1999, 2002) proposed a method of estimating the coronal magnetic field strengths ($B$) and magnetic loop lengths ($L$) of solar and stellar flares, on the basis of magnetohydrodynamic simulations of the magnetic reconnection model. Using the scaling law provided by Shibata & Yokoyama (1999, 2002), $B$ and $L$ are obtained as functions of the emission measure ($EM=n^2L^3$) and temperature ($T$) at the flare peak. Here, $n$ is the coronal electron density of the flares. This scaling law enables the estimation of $B$ and $L$ for unresolved stellar flares from the observable physical quantities $EM$ and $T$, which is helpful for studying stellar surface activities. To apply this scaling law to stellar flares, we discuss its validity for spatially resolved solar flares. $EM$ and $T$ were calculated from GOES soft X-ray flux data, and $B$ and $L$ are theoretically estimated using the scaling law. For the same flare events, $B$ and $L$ were also observationally estimated with images taken...
From divots to swales: Hillslope sediment transport across divers length scales
Furbish, David Jon; Haff, Peter K.
2010-09-01
In soil-mantled steeplands, soil motions associated with creep, ravel, rain splash, soil slips, tree throw, and rodent activity are patchy and intermittent and involve widely varying travel distances. To describe the collective effect of these motions, we formulate a nonlocal expression for the soil flux. This probabilistic formulation involves upslope and downslope convolutions of land surface geometry to characterize motions in both directions, notably accommodating the bidirectional dispersal of material on gentle slopes as well as mostly downslope dispersal on steeper slopes, and it distinguishes between the mobilization of soil material and the effect of surface slope in giving a downslope bias to the dispersal of mobilized material. The formulation separates dispersal associated with intermittent surface motions from the slower bulk behavior associated with small-scale bioturbation and similar dilational processes operating mostly within the soil column. With a uniform rate of mobilization of soil material, the nearly parabolic form of a hillslope profile at steady state resembles a diffusive behavior. With a slope-dependent rate of mobilization, the steady state hillslope profile takes on a nonparabolic form where land surface elevation varies with downslope distance x as xa with a ˜ 3/2, consistent with field observations and where the flux increases nonlinearly with increasing slope. The convolution description of the soil flux, when substituted into a suitable expression of conservation, yields a nonlinear Fokker-Planck equation and can be mapped to discrete particle models of hillslope behavior and descriptions of soil-grain transport by rain splash as a stochastic advection-dispersion process.
Age-related changes in the plasticity and toughness of human cortical bone at multiple length-scales
Zimmermann, Elizabeth A.; Schaible, Eric; Bale, Hrishikesh; Barth, Holly D.; Tang, Simon Y.; Reichert, Peter; Busse, Bjoern; Alliston, Tamara; Ager III, Joel W.; Ritchie, Robert O.
2011-08-10
The structure of human cortical bone evolves over multiple length-scales from its basic constituents of collagen and hydroxyapatite at the nanoscale to osteonal structures at nearmillimeter dimensions, which all provide the basis for its mechanical properties. To resist fracture, bone’s toughness is derived intrinsically through plasticity (e.g., fibrillar sliding) at structural-scales typically below a micron and extrinsically (i.e., during crack growth) through mechanisms (e.g., crack deflection/bridging) generated at larger structural-scales. Biological factors such as aging lead to a markedly increased fracture risk, which is often associated with an age-related loss in bone mass (bone quantity). However, we find that age-related structural changes can significantly degrade the fracture resistance (bone quality) over multiple lengthscales. Using in situ small-/wide-angle x-ray scattering/diffraction to characterize sub-micron structural changes and synchrotron x-ray computed tomography and in situ fracture-toughness measurements in the scanning electron microscope to characterize effects at micron-scales, we show how these age-related structural changes at differing size-scales degrade both the intrinsic and extrinsic toughness of bone. Specifically, we attribute the loss in toughness to increased non-enzymatic collagen cross-linking which suppresses plasticity at nanoscale dimensions and to an increased osteonal density which limits the potency of crack-bridging mechanisms at micron-scales. The link between these processes is that the increased stiffness of the cross-linked collagen requires energy to be absorbed by “plastic” deformation at higher structural levels, which occurs by the process of microcracking.
Scale-up considerations relevant to experimental studies of nuclear waste-package behavior
Coles, D.G.; Peters, R.D.
1986-04-01
Results from a study that investigated whether testing large-scale nuclear waste-package assemblages was technically warranted are reported. It was recognized that the majority of the investigations for predicting waste-package performance to date have relied primarily on laboratory-scale experimentation. However, methods for the successful extrapolation of the results from such experiments, both geometrically and over time, to actual repository conditions have not been well defined. Because a well-developed scaling technology exists in the chemical-engineering discipline, it was presupposed that much of this technology could be applicable to the prediction of waste-package performance. A review of existing literature documented numerous examples where a consideration of scaling technology was important. It was concluded that much of the existing scale-up technology is applicable to the prediction of waste-package performance for both size and time extrapolations and that conducting scale-up studies may be technically merited. However, the applicability for investigating the complex chemical interactions needs further development. It was recognized that the complexity of the system, and the long time periods involved, renders a completely theoretical approach to performance prediction almost hopeless. However, a theoretical and experimental study was defined for investigating heat and fluid flow. It was concluded that conducting scale-up modeling and experimentation for waste-package performance predictions is possible using existing technology. A sequential series of scaling studies, both theoretical and experimental, will be required to formulate size and time extrapolations of waste-package performance.
The gluino-glue particle and relevant scales for the simulations of supersymmetric Yang-Mills theory
Bergner, Georg; Münster, Gernot; Sandbrink, Dirk; Özugurel, Umut D
2012-01-01
Supersymmetric Yang-Mills theory is in several respects different from QCD and pure Yang-Mills theory. Therefore, a reinvestigation of the scales, at which finite size effects and lattice artifacts become relevant, is necessary. Both, finite size effects and lattice artifacts, induce a breaking of supersymmetry. In view of the unexpected mass gap between bosonic and fermionic particles an estimation of these effects is essential.
Valentin Jossen
2016-01-01
Full Text Available The potential of human mesenchymal stem cells (hMSCs for allogeneic cell therapies has created a large amount of interest. However, this presupposes the availability of efficient scale-up procedures. Promising results have been reported for stirred bioreactors that operate with microcarriers. Recent publications focusing on microcarrier-based stirred bioreactors have demonstrated the successful use of Computational Fluid Dynamics (CFD and suspension criteria (NS1u, NS1 for rapidly scaling up hMSC expansions from mL- to pilot scale. Nevertheless, one obstacle may be the formation of large microcarrier-cell-aggregates, which may result in mass transfer limitations and inhomogeneous distributions of stem cells in the culture broth. The dependence of microcarrier-cell-aggregate formation on impeller speed and shear stress levels was investigated for human adipose derived stromal/stem cells (hASCs at the spinner scale by recording the Sauter mean diameter (d32 versus time. Cultivation at the suspension criteria provided d32 values between 0.2 and 0.7 mm, the highest cell densities (1.25 × 106 cells mL−1 hASCs, and the highest expansion factors (117.0 ± 4.7 on day 7, while maintaining the expression of specific surface markers. Furthermore, suitability of the suspension criterion NS1u was investigated for scaling up microcarrier-based processes in wave-mixed bioreactors for the first time.
A. Daniyel Raj
2015-03-01
Full Text Available During many decades, continuous device performance improvement has been made possible only through device scaling. But presently, due to aggressive scaling at the sub-micron or nanometer region, the conventional planner silicon technology is suffering from the fundamental physical limits. Such imposed limits on further downscaling of silicon planner technology have lead to alternative device technology like Silicon-On-Insulator (SOI technology. Due-to some of its inherent advantages, the Silicon-On-Insulator (SOI technology has reduced the Short-channel-effects (SCEs and thus increased transistor scalability. Till now, intense research interests have been paid in practical fabrication and theoretical modeling of SOI MOSFETs but a little attention has been paid to understand the circuit level performance improvement with nano-scale SOI MOSFETs. The circuit level performance analysis of SOI MOSFET is highly essential to understand the impact of SOI technology on next level VLSI circuit and chip design and for doing so device compact models are high on demand. In such scenario, under present research, a physics based compact device model of SOI MOSFET has been developed. At the first phase of the compact model development, a physics based threshold voltage model has been developed by solving 2-D Poisson’s equation at the channel region and at the second phase, a current-voltage model has been developed with drift-diffusion analysis. Different SCEs, valid at nano-scale, are effectively incorporated in threshold voltage and Current-Voltage model. At the third phase, using the compact model, the Voltage Transfer Characteristics (VTC for a nano-scale SOI CMOS inverter has been derived with graphical analysis. The impacts of different device parameters e.g.; channel length and channel doping concentration on VTC has been investigated through simulation and the results have been analyzed.
Namekata, Kosuke; Sakaue, Takahito; Watanabe, Kyoko; Asai, Ayumi; Shibata, Kazunari
2017-02-01
Shibata and Yokoyama (1999, ApJ, 526, L49; 2002, ApJ, 577, 422) proposed a method of estimating the coronal magnetic field strength (B) and magnetic loop length (L) of solar and stellar flares, on the basis of magnetohydrodynamic simulations of the magnetic reconnection model. Using the scaling law provided by Shibata and Yokoyama (1999, ApJ, 526, L49; 2002, ApJ, 577, 422), we obtain B and L as functions of the emission measure (EM = n2L3) and temperature (T) at the flare peak. Here, n is the coronal electron density of the flares. This scaling law enables the estimation of B and L for unresolved stellar flares from the observable physical quantities EM and T, which is helpful for studying stellar surface activities. To apply this scaling law to stellar flares, we discuss its validity for spatially resolved solar flares. Quantities EM and T are calculated from GOES (Geostationary Operational Environmental Satellite) soft X-ray flux data, and B and L are theoretically estimated using the scaling law. For the same flare events, B and L were also observationally estimated with images taken by the Solar Dynamics Observatory (SDO)/Helioseismic and Magnetic Imager (HMI) Magnetogram and Atmospheric Imaging Assembly (AIA) 94 Å pass band. As expected, a positive correlation was found between the theoretically and observationally estimated values. We interpret this result as indirect evidence that flares are caused by magnetic reconnection. Moreover, this analysis makes us confident about the validity of applying this scaling law to stellar flares as well as solar flares.
Marine Climate Services ‐ Forecasting the state of the ocean at end‐user relevant time‐scale
Payne, Mark
Recent advances in oceanographic modelling mean that today we can forecast the state of the ocean with meaningful skill up to a decade in advance. Such forecasts are potentially of great value to society, as they span the gap between the short (days-to-weeks) time scales of weather forecasts and ......) in the North Atlantic. Further opportunities for forecasting variables, both globally and that are of direct relevance to Danish end-users will also be presented.......Recent advances in oceanographic modelling mean that today we can forecast the state of the ocean with meaningful skill up to a decade in advance. Such forecasts are potentially of great value to society, as they span the gap between the short (days-to-weeks) time scales of weather forecasts...... and the long (century) time-scales of climate projections: importantly, these are the time scales where most users make important decisions. However, a translation step is required to convert the outputs from these models, which are typically physical variables, into variables that are directly relevant to end...
The relevance of non-generic events in scale space models
Kuijper, Arjan; Florack, L.
2002-01-01
In order to investigate the deep structure of Gaussian scale space images, one needs to understand the behaviour of spatial critical points under the influence of blurring. We show how the mathematical framework of catastrophe theory can be used to describe and model the behaviour of critical point
Cammarota, Chiara; Seoane, Beatriz
2016-11-01
As a guideline for experimental tests of the ideal glass transition (random-pinning glass transition, RPGT) that shall be induced in a system by randomly pinning particles, we performed first-principle computations within the hypernetted chain approximation and numerical simulations of a hard-sphere model of a glass former. We obtain confirmation of the expected enhancement of glassy behavior under the procedure of random pinning. We present the analytical phase diagram as a function of c and of the packing fraction ϕ , showing a line of RPGT ending in a critical point. We also obtain microscopic results on cooperative length scales characterizing medium-range amorphous order in hard-sphere glasses and indirect quantitative information on a key thermodynamic quantity defined in proximity to ideal glass transitions, the amorphous surface tension. Finally, we present numerical results of pair correlation functions able to differentiate the liquid and the glass phases, as predicted by the analytic computations.
Garrido, Nephtali
2012-01-01
We put to the test an effective three-dimensional electrostatic potential, obtained effectively by considering an electrostatic source inside a (5+$p$)-dimensional braneworld scenario with $p$ compact and one infinite spacial extra dimensions in the RS II-$p$ model, for $p=1$ and $p=2$. This potential is regular at the source and matches the standard Coulomb potential outside a neighborhood. We use variational and perturbative approximation methods to calculate corrections to the ground energy of the Helium atom modified by this potential, by making use of a 6 and 39-parameter trial wave function of Hylleraas type for the ground state. These corrections to the ground-state energy are compared with experimental data for Helium atom in order to set bounds for the extra dimensions length scale. We find that these bounds are less restrictive than the ones obtained by Morales et. al. through a calculation using the Lamb shift in Hydrogen.
Ma, Li-Juan; Ji, Xiao-Li; Chen, Yuan-Cong; Xia, Hao-Guang; Zhu, Chen-Xin; Guo, Qiang; Yan, Feng
2014-09-01
The recently developed four Rsd extraction methods from a single device, involving the constant-mobility method, the direct Id—Vgs method, the conductance method and the Y-function method, are evaluated on 32 nm n-channel metal-oxide-semiconductor field-effect transistors (nMOSFETs). It is found that Rsd achieved from the constant-mobility method exhibits the channel length independent characteristics. The L-dependent Rsd extracted from the other three methods is proven to be associated with the gate-voltage-induced mobility degradation in the extraction procedures. Based on L-dependent behaviors of Rsd, a new method is proposed for accurate series resistance extraction on deeply scaled MOSFETs.
Rahbari, A; Montazerian, H; Davoodi, E; Homayoonfar, S
2017-02-01
The main aim of this research is to numerically obtain the permeability coefficient in the cylindrical scaffolds. For this purpose, a mathematical analysis was performed to derive an equation for desired porosity in terms of morphological parameters. Then, the considered cylindrical geometries were modeled and the permeability coefficient was calculated according to the velocity and pressure drop values based on the Darcy's law. In order to validate the accuracy of the present numerical solution, the obtained permeability coefficient was compared with the published experimental data. It was observed that this model can predict permeability with the utmost accuracy. Then, the effect of geometrical parameters including porosity, scaffold pore structure, unit cell size, and length of the scaffolds as well as entrance mass flow rate on the permeability of porous structures was studied. Furthermore, a parametric study with scaling laws analysis of sample length and mass flow rate effects on the permeability showed good fit to the obtained data. It can be concluded that the sensitivity of permeability is more noticeable at higher porosities. The present approach can be used to characterize and optimize the scaffold microstructure due to the necessity of cell growth and transferring considerations.
Licquia, Timothy C.; Newman, Jeffrey A.
2016-11-01
The exponential scale length (L d ) of the Milky Way’s (MW’s) disk is a critical parameter for describing the global physical size of our Galaxy, important both for interpreting other Galactic measurements and helping us to understand how our Galaxy fits into extragalactic contexts. Unfortunately, current estimates span a wide range of values and are often statistically incompatible with one another. Here, we perform a Bayesian meta-analysis to determine an improved, aggregate estimate for L d , utilizing a mixture-model approach to account for the possibility that any one measurement has not properly accounted for all statistical or systematic errors. Within this machinery, we explore a variety of ways of modeling the nature of problematic measurements, and then employ a Bayesian model averaging technique to derive net posterior distributions that incorporate any model-selection uncertainty. Our meta-analysis combines 29 different (15 visible and 14 infrared) photometric measurements of L d available in the literature; these involve a broad assortment of observational data sets, MW models and assumptions, and methodologies, all tabulated herein. Analyzing the visible and infrared measurements separately yields estimates for L d of {2.71}-0.20+0.22 kpc and {2.51}-0.13+0.15 kpc, respectively, whereas considering them all combined yields 2.64 ± 0.13 kpc. The ratio between the visible and infrared scale lengths determined here is very similar to that measured in external spiral galaxies. We use these results to update the model of the Galactic disk from our previous work, constraining its stellar mass to be {4.8}-1.1+1.5× {10}10 M ⊙, and the MW’s total stellar mass to be {5.7}-1.1+1.5× {10}10 M ⊙.
The relevance of cartographic scale in interactive and multimedia cartographic information systems
Mirjanka Lechthaler
2004-09-01
Full Text Available The application of new technologies in the processes of gathering, analysing, transforming, visualizing and communicating of space data and geoinformation offers a great challenge for cartography. Cartographic information provision as described in several cartographic models, which is included in cartographic information systems depend on the graphical presentation/visualization at certain scales. That necessitates a need to define the capacity or content borders (geometry and semantic for cognition and communication. However, currently we need and use maps as a vehicle for transportation of spatial and temporal information. Graphic constructions of geoanalogies, linked with interaction, multimedia sequences and animations, support effective geocommunication, bridging the gaps imposed by having to work at pre-defined scales. This paper illustrates two interactive information systems, which were conceptualised and prototyped at the Institute of Cartography and Geomedia Technique, Vienna University of Technology.
Mosby, Matthew; Matouš, Karel
2015-12-01
Three-dimensional simulations capable of resolving the large range of spatial scales, from the failure-zone thickness up to the size of the representative unit cell, in damage mechanics problems of particle reinforced adhesives are presented. We show that resolving this wide range of scales in complex three-dimensional heterogeneous morphologies is essential in order to apprehend fracture characteristics, such as strength, fracture toughness and shape of the softening profile. Moreover, we show that computations that resolve essential physical length scales capture the particle size-effect in fracture toughness, for example. In the vein of image-based computational materials science, we construct statistically optimal unit cells containing hundreds to thousands of particles. We show that these statistically representative unit cells are capable of capturing the first- and second-order probability functions of a given data-source with better accuracy than traditional inclusion packing techniques. In order to accomplish these large computations, we use a parallel multiscale cohesive formulation and extend it to finite strains including damage mechanics. The high-performance parallel computational framework is executed on up to 1024 processing cores. A mesh convergence and a representative unit cell study are performed. Quantifying the complex damage patterns in simulations consisting of tens of millions of computational cells and millions of highly nonlinear equations requires data-mining the parallel simulations, and we propose two damage metrics to quantify the damage patterns. A detailed study of volume fraction and filler size on the macroscopic traction-separation response of heterogeneous adhesives is presented.
Kim, Philseok; Kreder, Michael J; Alvarenga, Jack; Aizenberg, Joanna
2013-04-10
Lubricant-infused textured solid substrates are gaining remarkable interest as a new class of omni-repellent nonfouling materials and surface coatings. We investigated the effect of the length scale and hierarchy of the surface topography of the underlying substrates on their ability to retain the lubricant under high shear conditions, which is important for maintaining nonwetting properties under application-relevant conditions. By comparing the lubricant loss, contact angle hysteresis, and sliding angles for water and ethanol droplets on flat, microscale, nanoscale, and hierarchically textured surfaces subjected to various spinning rates (from 100 to 10,000 rpm), we show that lubricant-infused textured surfaces with uniform nanofeatures provide the most shear-tolerant liquid-repellent behavior, unlike lotus leaf-inspired superhydrophobic surfaces, which generally favor hierarchical structures for improved pressure stability and low contact angle hysteresis. On the basis of these findings, we present generalized, low-cost, and scalable methods to manufacture uniform or regionally patterned nanotextured coatings on arbitrary materials and complex shapes. After functionalization and lubrication, these coatings show robust, shear-tolerant omniphobic behavior, transparency, and nonfouling properties against highly contaminating media.
Florian Holon
Full Text Available Ecosystem services provided by oceans and seas support most human needs but are threatened by human activities. Despite existing maps illustrating human impacts on marine ecosystems, information remains either large-scale but rough and insufficient for stakeholders (1 km² grid, lack of data along the coast or fine-scale but fragmentary and heterogeneous in methodology. The objectives of this study are to map and quantify the main pressures exerted on near-coast marine ecosystems, at a large spatial scale though in fine and relevant resolution for managers (one pixel = 20 x 20 m. It focuses on the French Mediterranean coast (1,700 km of coastline including Corsica at a depth of 0 to 80 m. After completing and homogenizing data presently available under GIS on the bathymetry and anthropogenic pressures but also on the seabed nature and ecosystem vulnerability, we provide a fine modeling of the extent and impacts of 10 anthropogenic pressures on marine habitats. The considered pressures are man-made coastline, boat anchoring, aquaculture, urban effluents, industrial effluents, urbanization, agriculture, coastline erosion, coastal population and fishing. A 1:10 000 continuous habitat map is provided considering 11 habitat classes. The marine bottom is mostly covered by three habitats: infralittoral soft bottom, Posidonia oceanica meadows and circalittoral soft bottom. Around two thirds of the bottoms are found within medium and medium high cumulative impact categories. Seagrass meadows are the most impacted habitats. The most important pressures (in area and intensity are urbanization, coastal population, coastal erosion and man-made coastline. We also identified areas in need of a special management interest. This work should contribute to prioritize environmental needs, as well as enhance the development of indicators for the assessment of the ecological status of coastal systems. It could also help better apply and coordinate management measures
Holon, Florian; Mouquet, Nicolas; Boissery, Pierre; Bouchoucha, Marc; Delaruelle, Gwenaelle; Tribot, Anne-Sophie; Deter, Julie
2015-01-01
Ecosystem services provided by oceans and seas support most human needs but are threatened by human activities. Despite existing maps illustrating human impacts on marine ecosystems, information remains either large-scale but rough and insufficient for stakeholders (1 km² grid, lack of data along the coast) or fine-scale but fragmentary and heterogeneous in methodology. The objectives of this study are to map and quantify the main pressures exerted on near-coast marine ecosystems, at a large spatial scale though in fine and relevant resolution for managers (one pixel = 20 x 20 m). It focuses on the French Mediterranean coast (1,700 km of coastline including Corsica) at a depth of 0 to 80 m. After completing and homogenizing data presently available under GIS on the bathymetry and anthropogenic pressures but also on the seabed nature and ecosystem vulnerability, we provide a fine modeling of the extent and impacts of 10 anthropogenic pressures on marine habitats. The considered pressures are man-made coastline, boat anchoring, aquaculture, urban effluents, industrial effluents, urbanization, agriculture, coastline erosion, coastal population and fishing. A 1:10 000 continuous habitat map is provided considering 11 habitat classes. The marine bottom is mostly covered by three habitats: infralittoral soft bottom, Posidonia oceanica meadows and circalittoral soft bottom. Around two thirds of the bottoms are found within medium and medium high cumulative impact categories. Seagrass meadows are the most impacted habitats. The most important pressures (in area and intensity) are urbanization, coastal population, coastal erosion and man-made coastline. We also identified areas in need of a special management interest. This work should contribute to prioritize environmental needs, as well as enhance the development of indicators for the assessment of the ecological status of coastal systems. It could also help better apply and coordinate management measures at a relevant
Holon, Florian; Mouquet, Nicolas; Boissery, Pierre; Bouchoucha, Marc; Delaruelle, Gwenaelle; Tribot, Anne-Sophie; Deter, Julie
2015-01-01
Ecosystem services provided by oceans and seas support most human needs but are threatened by human activities. Despite existing maps illustrating human impacts on marine ecosystems, information remains either large-scale but rough and insufficient for stakeholders (1 km² grid, lack of data along the coast) or fine-scale but fragmentary and heterogeneous in methodology. The objectives of this study are to map and quantify the main pressures exerted on near-coast marine ecosystems, at a large spatial scale though in fine and relevant resolution for managers (one pixel = 20 x 20 m). It focuses on the French Mediterranean coast (1,700 km of coastline including Corsica) at a depth of 0 to 80 m. After completing and homogenizing data presently available under GIS on the bathymetry and anthropogenic pressures but also on the seabed nature and ecosystem vulnerability, we provide a fine modeling of the extent and impacts of 10 anthropogenic pressures on marine habitats. The considered pressures are man-made coastline, boat anchoring, aquaculture, urban effluents, industrial effluents, urbanization, agriculture, coastline erosion, coastal population and fishing. A 1:10 000 continuous habitat map is provided considering 11 habitat classes. The marine bottom is mostly covered by three habitats: infralittoral soft bottom, Posidonia oceanica meadows and circalittoral soft bottom. Around two thirds of the bottoms are found within medium and medium high cumulative impact categories. Seagrass meadows are the most impacted habitats. The most important pressures (in area and intensity) are urbanization, coastal population, coastal erosion and man-made coastline. We also identified areas in need of a special management interest. This work should contribute to prioritize environmental needs, as well as enhance the development of indicators for the assessment of the ecological status of coastal systems. It could also help better apply and coordinate management measures at a relevant
Miller, S.; Bankert, R.; Forsythe, J.; Mitrescu, C.; Reinke, D.; Austin, R.
2007-12-01
horizontal to construct pseudo three-dimensional information. These statistics are based on cloud-type classification, which are identifiable from cloud top observations by conventional 2-D observing systems. Preliminary cloud-type-dependent vertical structures, based on the CloudSat Level-2 Cloud Water Content (CWC) product, are presented for an assortment of cloud classifications. Such statistics can then be applied to the vertically-integrated liquid/ice water content as retrieved by 2-D sensors to distribute this water in the column according to type-dependency. In addition, the degree to which cloud layer base heights can be extended into the cross-track direction (e.g., given an observation of similar cloud-type from a conventional 2-D optical radiometer) can be assessed via correlation lengths computed along the CloudSat track. The effective result is a pseudo 3-D swath of cloud water content of potential use to operational support and numerical weather prediction analysis and/or validation. Preliminary results from the currently available compilation of CloudSat data are presented to illustrate conceptually the potential and limitations of such approaches.
Z. Yu
2012-07-01
Full Text Available High-latitude peatlands contain about one third of the world's soil organic carbon, most of which is derived from partly decomposed Sphagnum (peat moss plants. We conducted a meta-analysis based on a global data set of Sphagnum growth measurements collected from published literature to investigate the effects of bioclimatic variables on Sphagnum growth. Analysis of variance and general linear models were used to relate Sphagnum magellanicum and S. fuscum growth rates to photosynthetically active radiation integrated over the growing season (PAR0 and a moisture index. We found that PAR0 was the main predictor of Sphagnum growth for the global data set, and effective moisture was only correlated with moss growth at continental sites. The strong correlation between Sphagnum growth and PAR0 suggests the existence of a global pattern of growth, with slow rates under cool climate and short growing seasons, highlighting the important role of growing season length in explaining peatland biomass production. Large-scale patterns of cloudiness during the growing season might also limit moss growth. Although considerable uncertainty remains over the carbon balance of peatlands under a changing climate, our results suggest that increasing PAR0 as a result of global warming and lengthening growing seasons, without major change in cloudiness, could promote Sphagnum growth. Assuming that production and decomposition have the same sensitivity to temperature, this enhanced growth could lead to greater peat-carbon sequestration, inducing a negative feedback to climate change.
Goy, A.; Xiao, Y.H.; Passalaris, T. [Memorial Sloan-Kettering Cancer Center, New York, NY (United States)] [and others
1995-03-20
The PML gene located on chromosome band 15q22 is involved with the RAR{alpha} locus (17q21) in a balanced reciprocal translocation uniquely observed in acute promyelocytic leukemia. Physical mapping studies by pulsed-field gel electrophoresis revealed that the PML gene is flanked by two CpG islands that are separated by a variable distance in normal individuals. Several lines of evidence demonstrate that this is the consequence of a large insertion/deletion polymorphism linked to the PML locus: (1) overlapping fragments obtained with a variety of rare-cutting restriction enzymes demonstrated the same variability in distance between the flanking CpG islands; (2) mapping with restriction enzymes insensitive to CpG methylation confirmed that the findings were not a consequence of variable methylation of CpG dinucleotides; (3) the polymorphism followed a Mendelian inheritance pattern. This polymorphism is localized 3{prime} to the PML locus. There are five common alleles, described on the basis of BssHII fragments, ranging from 220 to 350 kb with increments of approximately 30 kb between alleles. Both heterozygous (61%) and homozygous (391%) patterns were observed in normal individuals. Mega-base-scale insertion/deletion restriction fragment length polymorphisms are very rare and have been described initially in the context of multigene families. Such structures have been also reported as likely regions of genetic instability. High-resolution restriction mapping of this particular structure linked to the PML locus is underway. 47 refs., 4 figs., 1 tab.
Raschke, Markus
2015-03-01
To understand and ultimately control the properties of most functional materials, from molecular soft-matter to quantum materials, requires access to the structure, coupling, and dynamics on the elementary time and length scales that define the microscopic interactions in these materials. To gain the desired nanometer spatial resolution with simultaneous spectroscopic specificity we combine scanning probe microscopy with different optical, including coherent, nonlinear, and ultrafast spectroscopies. The underlying near-field interaction mediated by the atomic-force or scanning tunneling microscope tip provides the desired deep-sub wavelength nano-focusing enabling few-nm spatial resolution. I will introduce our generalization of the approach in terms of the near-field impedance matching to a quantum system based on special optical antenna-tip designs. The resulting enhanced and qualitatively new forms of light-matter interaction enable measurements of quantum dynamics in an interacting environment or to image the electromagnetic local density of states of thermal radiation. Other applications include the inter-molecular coupling and dynamics in soft-matter hetero-structures, surface plasmon interferometry as a probe of electronic structure and dynamics in graphene, and quantum phase transitions in correlated electron materials. These examples highlight the general applicability of the new near-field microscopy approach, complementing emergent X-ray and electron imaging tools, aiming towards the ultimate goal of probing matter on its most elementary spatio-temporal level.
Somogyi, Andrea; Medjoubi, Kadda; Baranton, Gil; Le Roux, Vincent; Ribbens, Marc; Polack, François; Philippot, Pascal; Samama, Jean Pierre
2015-07-01
The Nanoscopium 155 m-long beamline of Synchrotron Soleil is dedicated to scanning hard X-ray nanoprobe techniques. Nanoscopium aims to reach ≤100 nm resolution in the 5-20 keV energy range for routine user experiments. The beamline design tackles the tight stability requirements of such a scanning nanoprobe by creating an overfilled secondary source, implementing all horizontally reflecting main beamline optics, applying high mechanical stability equipment and constructing a dedicated high-stability building envelope. Multi-technique scanning imaging and tomography including X-ray fluorescence spectrometry and spectro-microscopy, absorption, differential phase and dark-field contrasts are implemented at the beamline in order to provide simultaneous information on the elemental distribution, speciation and sample morphology. This paper describes the optical concept and the first measured performance of the Nanoscopium beamline followed by the hierarchical length-scale multi-technique imaging experiments performed with dwell times down to 3 ms per pixel.
P. Oshkai; M. Geveci; D. Rockwell; M. Pollack
2002-12-12
Flow-acoustic interactions due to fully turbulent inflow past a shallow axisymmetric cavity mounted in a pipe are investigated using a technique of high-image-density particle image velocimetry in conjunction with unsteady pressure measurements. This imaging leads to patterns of velocity, vorticity, streamline topology, and hydrodynamic contributions to the acoustic power integral. Global instantaneous images, as well as time-averaged images, are evaluated to provide insight into the flow physics during tone generation. Emphasis is on the manner in which the streamwise length scale of the cavity alters the major features of the flow structure. These image-based approaches allow identification of regions of the unsteady shear layer that contribute to the instantaneous hydrodynamic component of the acoustic power, which is necessary to maintain a flow tone. In addition, combined image analysis and pressure measurements allow categorization of the instantaneous flow patterns that are associated with types of time traces and spectra of the fluctuating pressure. In contrast to consideration based solely on pressure spectra, it is demonstrated that locked-on tones may actually exhibit intermittent, non-phase-locked images, apparently due to low damping of the acoustic resonator. Locked-on flow tones (without modulation or intermittency), locked-on flow tones with modulation, and non-locked-on oscillations with short-term, highly coherent fluctuations are defined and represented by selected cases. Depending on which of,these regimes occur, the time-averaged Q (quality)-factor and the dimensionless peak pressure are substantially altered.
Lee, Wei Li; Low, Hong Yee
2016-03-01
Micro- and nanoscale surface textures, when optimally designed, present a unique approach to improve surface functionalities. Coupling surface texture with shape memory polymers may generate reversibly tuneable surface properties. A shape memory polyetherurethane is used to prepare various surface textures including 2 μm- and 200 nm-gratings, 250 nm-pillars and 200 nm-holes. The mechanical deformation via stretching and recovery of the surface texture are investigated as a function of length scales and shapes. Results show the 200 nm-grating exhibiting more deformation than 2 μm-grating. Grating imparts anisotropic and surface area-to-volume effects, causing different degree of deformation between gratings and pillars under the same applied macroscopic strain. Full distribution of stress within the film causes the holes to deform more substantially than the pillars. In the recovery study, unlike a nearly complete recovery for the gratings after 10 transformation cycles, the high contribution of surface energy impedes the recovery of holes and pillars. The surface textures are shown to perform a switchable wetting function. This study provides insights into how geometric features of shape memory surface patterns can be designed to modulate the shape programming and recovery, and how the control of reversibly deformable surface textures can be applied to transfer microdroplets.
Wenbin Shen; Cunchao Peng
2016-01-01
Scientists pay great attention to different-time-scale signals in the length of day (LOD)variations ALOD,which provide signatures of the Earth's interior structure,couplings among different layers,and potential excitations of ocean and atmosphere.In this study,based on the ensemble empirical mode decomposition (EEMD),we analyzed the latest time series of ALOD data spanning from January 1962 to March 2015.We observed the signals with periods and amplitudes of about 0.5 month and 0.19 ms,1.0 month and 0.19 ms,0.5 yr and 0.22 ms,1.0 yr and 0.18 ms,2.28 yr and 0.03 ms,5.48 yr and 0.05 ms,respectively,in coincidence with the results of predecessors.In addition,some signals that were previously not definitely observed by predecessors were detected in this study,with periods and amplitudes of 9.13 d and 0.12 ms,13.69 yr and 0.10 ms,respectively.The mechanisms of the LOD fluctuations of these two signals are still open.
Z. Yu
2012-02-01
Full Text Available High-latitude peatlands contain about one third of the world's soil organic carbon, most of which is derived from partly decomposed Sphagnum (peat moss plants. We conducted a meta-analysis based on a global dataset of Sphagnum growth measurements collected from published literature to investigate the effects of bioclimatic variables on Sphagnum growth. Analysis of variance and general linear models were used to relate Sphagnum magellanicum and S. fuscum growth rates to photosynthetically active radiation integrated over the growing season (PAR0 and a moisture index. We found that PAR0 was the main predictor of Sphagnum growth for the global dataset, and effective moisture was only correlated with moss growth at continental sites. The strong correlation between Sphagnum growth and PAR0 suggests the existence of a global pattern of growth, with slow rates under cool climate and short growing seasons, highlighting the important role of temperature and growing season length in explaining peatland biomass production. Large-scale patterns of cloudiness during the growing season might also limit moss growth. Although considerable uncertainty remains over the carbon balance of peatlands under a changing climate, our results suggest that increasing PAR0 as a result of global warming and lengthening growing seasons could promote Sphagnum growth. Assuming that production and decomposition have the same sensitivity to temperature, this enhanced growth could lead to greater peat-carbon sequestration, inducing a negative feedback to climate change.
Fischer, Peter
2008-08-01
The magnetic properties of low dimensional solid state matter is of the utmost interest both scientifically as well as technologically. In addition to the charge of the electron which is the base for current electronics, by taking into account the spin degree of freedom in future spintronics applications open a new avenue. Progress towards a better physical understanding of the mechanism and principles involved as well as potential applications of nanomagnetic devices can only be achieved with advanced analytical tools. Soft X-ray microscopy providing a spatial resolution towards 10nm, a time resolution currently in the sub-ns regime and inherent elemental sensitivity is a very promising technique for that. This article reviews the recent achievements of magnetic soft X-ray microscopy by selected examples of spin torque phenomena, stochastical behavior on the nanoscale and spin dynamics in magnetic nanopatterns. The future potential with regard to addressing fundamental magnetic length and time scales, e.g. imaging fsec spin dynamics at upcoming X-ray sources is pointed out.
Sherley, Richard B; Botha, Philna; Underhill, Les G; Ryan, Peter G; van Zyl, Danie; Cockcroft, Andrew C; Crawford, Robert J M; Dyer, Bruce M; Cook, Timothée R
2017-03-01
Human activities are important drivers of marine ecosystem functioning. However, separating the synergistic effects of fishing and environmental variability on the prey base of non-target predators is difficult, often because prey availability estimates on appropriate scales are lacking. Understanding how prey abundance at different spatial scales links to population change can help integrate the needs of non-target predators into fisheries management by defining ecologically-relevant areas for spatial protection. We investigated the local population response (number of breeders) of the bank cormorant Phalacrocorax neglectus, a range-restricted endangered seabird, to the availability of its prey, the heavily-fished west coast rock lobster Jasus lalandii. Using Bayesian state-space modeled cormorant counts at three colonies, 22 years of fisheries-independent data on local lobster abundance and generalized additive modeling, we determined the spatial-scale pertinent to these relationships in areas of differing lobster availability. Cormorant numbers responded positively to lobster availability in the intermediate and high abundance regions, but not where regime shifts and fishing pressure have depleted lobster stocks. The relationships were strongest at 20-30 km, greater than the cormorants' foraging range when breeding, and may have been influence by prey availability for non-breeding birds, prey switching or prey ecology. Our results highlight the importance of considering the scale of ecological relationships in marine spatial planning and suggest that designing spatial protection around focal species can benefit marine predators across their full life cycle. We propose the precautionary implementation of small-scale marine protected areas, followed by robust assessment and adaptive-management, to confirm population-level benefits for the cormorants, their prey and the wider ecosystem, without negative impacts on local fisheries. This article is protected by
Lecomte, Tania; Corbière, Marc; Laisné, François
2006-06-30
Studies investigating self-esteem in individuals with severe mental illness, either as a treatment goal, outcome or correlate to other variables, have increased over the past few years. One of the main difficulties in assessing self-esteem is the assessment itself, often measuring global and stable self-esteem as in the Rosenberg Self-Esteem Scale, or requiring extensive training and long interviews. The present article aims at demonstrating the relevance of the French and English versions of the Self-Esteem Rating Scale-Short Form with individuals with severe mental illness. The instrument's reliability and validity were investigated in a sample of 250 French Canadian college students, 247 British college students and three samples of English- or French-speaking individuals with severe mental illness (N=254, N=150 and N=171). Confirmatory factor analysis revealed that a shorter version of the instrument (20 items), with a positive and a negative self-esteem factor, had a great validity for all the samples studied. The Self-Esteem Rating Scale-Short Form, with its positive and negative self-esteem subscales, appears to be a valid and reliable self-esteem measure for individuals with mental health problems. Limitations of this study and future directions are discussed.
Zhang, Fan; Levine, Lyle E.; Allen, Andrew J.; Campbell, Carelyn E.; Creuziger, Adam A.; Kazantseva, Nataliya; Ilavsky, Jan
2016-06-01
The precipitate structure and precipitation kinetics in an Al-Cu-Mg alloy (AA2024) aged at 190 °C, 208 °C, and 226 °C have been studied using ex situ Transmission Electron Microscopy (TEM) and in situ synchrotron-based, combined ultra-small angle X-ray scattering, small angle X-ray scattering (SAXS), and wide angle X-ray scattering (WAXS) across a length scale from sub-Angstrom to several micrometers. TEM brings information concerning the nature, morphology, and size of the precipitates while SAXS and WAXS provide qualitative and quantitative information concerning the time-dependent size and volume fraction evolution of the precipitates at different stages of the precipitation sequence. Within the experimental time resolution, precipitation at these ageing temperatures involves dissolution of nanometer-sized small clusters and formation of the planar S phase precipitates. Using a three-parameter scattering model constructed on the basis of TEM results, we established the temperature-dependent kinetics for the cluster-dissolution and S-phase formation processes simultaneously. These two processes are shown to have different kinetic rates, with the cluster-dissolution rate approximately double the S-phase formation rate. We identified a dissolution activation energy at (149.5 ± 14.6) kJ mol-1, which translates to (1.55 ± 0.15) eV/atom, as well as an activation energy for the formation of S precipitates at (129.2 ± 5.4) kJ mol-1, i.e. (1.33 ± 0.06) eV/atom. Importantly, the SAXS/WAXS results show the absence of an intermediate Guinier-Preston Bagaryatsky 2 (GPB2)/S" phase in the samples under the experimental ageing conditions. These results are further validated by precipitation simulations that are based on Langer-Schwartz theory and a Kampmann-Wagner numerical method.
P Oshkai; M Geveci; D Rockwell; M Pollack
2004-05-24
Flow-acoustic interactions due to fully turbulent inflow past a shallow axisymmetric cavity mounted in a pipe, which give rise to flow tones, are investigated using a technique of high-image-density particle image velocimetry in conjunction with unsteady pressure measurements. This imaging leads to patterns of velocity, vorticity, streamline topology, and hydrodynamic contributions to the acoustic power integral. Global instantaneous images, as well as time-averaged images, are evaluated to provide insight into the flow physics during tone generation. Emphasis is on the manner in which the streamwise length scale of the cavity alters the major features of the flow structure. These image-based approaches allow identification of regions of the unsteady shear layer that contribute to the instantaneous hydrodynamic component of the acoustic power, which is necessary to maintain a flow tone. In addition, combined image analysis and pressure measurements allow categorization of the instantaneous flow patterns that are associated with types of time traces and spectra of the fluctuating pressure. In contrast to consideration based solely on pressure spectra, it is demonstrated that locked-on tones may actually exhibit intermittent, non-phase-locked images, apparently due to low damping of the acoustic resonator. Locked-on flow tones (without modulation or intermittency), locked-on flow tones with modulation, and non-locked-on oscillations with short-term, highly coherent fluctuations are defined and represented by selected cases. Depending on which of these regimes occur, the time-averaged Q (quality)-factor and the dimensionless peak pressure are substantially altered.
Siddique, N A; Salehi, Amir; Wei, Zi; Liu, Dong; Sajjad, Syed D; Liu, Fuqiang
2015-08-03
The charge and discharge of lithium ion batteries are often accompanied by electrochemically driven phase-transformation processes. In this work, two in situ and operando methods, that is, micro-Raman spectroscopy and X-ray diffraction (XRD), have been combined to study the phase-transformation process in LiFePO4 at two distinct length scales, namely, particle-level scale (∼1 μm) and macroscopic scale (∼several cm). In situ Raman studies revealed a discrete mode of phase transformation at the particle level. Besides, the preferred electrochemical transport network, particularly the carbon content, was found to govern the sequence of phase transformation among particles. In contrast, at the macroscopic level, studies conducted at four different discharge rates showed a continuous but delayed phase transformation. These findings uncovered the intricate phase transformation in LiFePO4 and potentially offer valuable insights into optimizing the length-scale-dependent properties of battery materials.
Mondal, Jahur A; Namboodiri, V; Mathi, P; Singh, Ajay K
2017-04-06
Although the hydrophobic size of an amphiphile plays a key role in various chemical, biological, and atmospheric processes, its effect at macroscopic aqueous interfaces (e.g., air-water, oil-water, cell membrane-water, etc.), which are ubiquitous in nature, is not well understood. Here we report the hydrophobic alkyl chain length dependent structural and orientational transformations of water at alcohol (CnH2n+1OH, n = 1-12)-water interfaces using interface-selective heterodyne-detected vibrational sum frequency generation (HD-VSFG) and Raman multivariate curve resolution (Raman-MCR) spectroscopic techniques. The HD-VSFG results reveal that short-chain alcohols (CnH2n+1OH, n alcohols (CnH2n+1OH, n > 4, i.e., beyond 1-butanol) make the interfacial water more strongly H-bonded and reversely orientated; the OH stretch band maximum appears at ∼3200 cm(-1), and the H atoms are pointed away from the bulk water, that is, "H-up" oriented. Interestingly, for the alcohol of intermediate chain length (CnH2n+1OH, n = 4, i.e, 1-butanol), the interface is quite unstable even after hours of its formation and the time-averaged result is qualitatively similar to that of the long-chain alcohols, indicating a structural/orientational crossover of interfacial water at the 1-butanol-water interface. pH-dependent HD-VSFG measurements (with H2O as well as isotopically diluted water, HOD) suggest that the structural/orientational transformation of water at the long-chain alcohol-water interface is associated with the adsorption of OH(-) anion at the interface. Vibrational mapping of the water structure in the hydration shell of OH(-) anion (obtained by Raman-MCR spectroscopy of NaOH in HOD) clearly shows that the water becomes strongly H-bonded (OH stretch max. ≈ 3200 cm(-1)) while hydrating the OH(-) anion. Altogether, it is conceivable that alcohols of different hydrophobic chain lengths that are present in the troposphere will differently affect the interfacial electrostatics and
Amplified fragment length polymorphism (AFLP) markers can be developed more quickly and at a lower cost than microsatellite and single nucleotide polymorphism markers, which makes them ideal markers for large-scale studies of understudied taxa — such as species at risk. However,...
Swartzentruber, Brian Shoemaker
2009-04-01
This document is the final SAND Report for the LDRD Project 102660 - 'Bottomup' meets 'top-down': Self-assembly to direct manipulation of nanostructures on length scales from atoms to microns - funded through the Strategic Partnerships investment area as part of the National Institute for Nano-Engineering (NINE) project.
Kuchanov, S.; Zharnikov, T.; Brinke, G. ten
2011-01-01
A theoretical study on the effect of polydispersity of two-length-scale binary multiblock copolymers on the shape of the structure factor is presented. A bifurcation diagram is constructed showing the partition of the parameter space into domains differing in the way in which the homogeneous melt lo
Kuchanov, S.; Zharnikov, T.; Brinke, G. ten
2011-01-01
A theoretical study on the effect of polydispersity of two-length-scale binary multiblock copolymers on the shape of the structure factor is presented. A bifurcation diagram is constructed showing the partition of the parameter space into domains differing in the way in which the homogeneous melt lo
Teo, Boon K.; Li, Wai-Kee
2011-01-01
This article is divided into two parts. In the first part, the atomic unit (au) system is introduced and the scales of time, space (length), and speed, as well as those of mass and energy, in the atomic world are discussed. In the second part, the utility of atomic units in quantum mechanical and spectroscopic calculations is illustrated with…
Buckley, Patrick G; Das, Sudipto; Bryan, Kenneth; Watters, Karen M; Alcock, Leah; Koster, Jan; Versteeg, Rogier; Stallings, Raymond L
2011-05-15
The downregulation of specific genes through DNA hypermethylation is a major hallmark of cancer, although the extent and genomic distribution of hypermethylation occurring within cancer genomes is poorly understood. We report on the first genome-wide analysis of DNA methylation alterations in different neuroblastic tumor subtypes and cell lines, revealing higher order organization and clinically relevant alterations of the epigenome. The methylation status of 33,485 discrete loci representing all annotated CpG islands and RefSeq gene promoters was assessed in primary neuroblastic tumors and cell lines. A comparison of genes that were hypermethylated exclusively in the clinically favorable ganglioneuroma/ganglioneuroblastoma tumors revealed that nine genes were associated with poor clinical outcome when overexpressed in the unfavorable neuroblastoma (NB) tumors. Moreover, an integrated DNA methylation and copy number analysis identified 80 genes that were recurrently concomitantly deleted and hypermethylated in NB, with 37 reactivated by 5-aza-deoxycytidine. Lower expression of four of these genes was correlated with poor clinical outcome, further implicating their inactivation in aggressive disease pathogenesis. Analysis of genome-wide hypermethylation patterns revealed 70 recurrent large-scale blocks of contiguously hypermethylated promoters/CpG islands, up to 590 kb in length, with a distribution bias toward telomeric regions. Genome-wide hypermethylation events in neuroblastic tumors are extensive and frequently occur in large-scale blocks with a significant bias toward telomeric regions, indicating that some methylation alterations have occurred in a coordinated manner. Our results indicate that methylation contributes toward the clinicopathological features of neuroblastic tumors, revealing numerous genes associated with poor patient survival in NB.
Hösel, Markus; Dam, Henrik Friis; Krebs, Frederik C
2015-01-01
We describe and review how the scaling of printed energy technologies not only requires scaling of the input materials but also the machinery used in the processes. The general consensus that ultrafast processing of technologies with large energy capacity can only be realized using roll-to-roll m......We describe and review how the scaling of printed energy technologies not only requires scaling of the input materials but also the machinery used in the processes. The general consensus that ultrafast processing of technologies with large energy capacity can only be realized using roll...
Qin, Zhao; Fabre, Andrea; Buehler, Markus J
2013-05-01
The stability of alpha helices is important in protein folding, bioinspired materials design, and controls many biological properties under physiological and disease conditions. Here we show that a naturally favored alpha helix length of 9 to 17 amino acids exists at which the propensity towards the formation of this secondary structure is maximized. We use a combination of thermodynamical analysis, well-tempered metadynamics molecular simulation and statistical analyses of experimental alpha helix length distributions and find that the favored alpha helix length is caused by a competition between alpha helix folding, unfolding into a random coil and formation of higher-order tertiary structures. The theoretical result is suggested to be used to explain the statistical distribution of the length of alpha helices observed in natural protein structures. Our study provides mechanistic insight into fundamental controlling parameters in alpha helix structure formation and potentially other biopolymers or synthetic materials. The result advances our fundamental understanding of size effects in the stability of protein structures and may enable the design of de novo alpha-helical protein materials.
Spreading lengths of Hermite polynomials
Sánchez-Moreno, P; Manzano, D; Yáñez, R; 10.1016/j.cam.2009.09.043
2009-01-01
The Renyi, Shannon and Fisher spreading lengths of the classical or hypergeometric orthogonal polynomials, which are quantifiers of their distribution all over the orthogonality interval, are defined and investigated. These information-theoretic measures of the associated Rakhmanov probability density, which are direct measures of the polynomial spreading in the sense of having the same units as the variable, share interesting properties: invariance under translations and reflections, linear scaling and vanishing in the limit that the variable tends towards a given definite value. The expressions of the Renyi and Fisher lengths for the Hermite polynomials are computed in terms of the polynomial degree. The combinatorial multivariable Bell polynomials, which are shown to characterize the finite power of an arbitrary polynomial, play a relevant role for the computation of these information-theoretic lengths. Indeed these polynomials allow us to design an error-free computing approach for the entropic moments (w...
Buyukdagli, S; Buyukdagli, Sahin; Joyeux, Marc
2006-01-01
We used the Transfer-Integral method to compute, with an uncertainty smaller than 5%, the six fundamental characteristic exponents of two dynamical models for DNA thermal denaturation and investigate the validity of the scaling laws. Doubts concerning this point arise because the investigated systems (i) have a divergent internal length, (ii) are described by a divergent order parameter, (iii) are of dimension 1. We found that the assumption that the free energy can be described by a single homogeneous function is robust, despite the divergence of the order parameter, so that Rushbrooke's and Widom's identities are valid relations. Josephson's identity is instead not satisfied. This is probably due to the divergence of the internal length, which invalidates the assumption that the correlation length is solely responsible for singular contributions to thermodynamic quantities. Fisher's identity is even wronger. We showed that this is due to the d=1 dimensionality and obtained an alternative law, which is well ...
and, Chen Xu; Aryanfar, Asghar; Viswanathan, Venkatasubramanian; Greer, Julia R
2016-01-01
Most next-generation Li-ion battery chemistries require a functioning lithium metal (Li) anode. However, its application in secondary batteries has been inhibited because of uncontrollable dendrite growth during cycling. Mechanical suppression of dendrite growth through solid polymer electrolytes (SPE) or through robust separators has shown the most potential for alleviating this problem. Studies of the mechanical behavior of Li at any length scale and temperature are virtually non-existent because of its extreme reactivity, which renders sample preparation, transfer, microstructure characterization and mechanical testing prohibitively challenging. We conduct nano-mechanical experiments in an in-situ Scanning Electron Microscope and show that micron-sized Li attains extremely high strengths of 105 MPa at room temperature and of 35MPa at 90$^\\circ$C. We demonstrate that single crystalline Li exhibits a power-law size-effect at the micron- and sub-micron length scales, with the strengthening exponent of -0.68 a...
Shaw, A.; Ghosh, A., E-mail: sspag@iacs.res.in [Department of Solid State Physics, Indian Association for the Cultivation of Science, Jadavpur, Kolkata 700032 (India)
2014-10-28
We have studied the mixed network former effect on the dynamics of lithium ions in borotellurite glasses in wide composition and temperature ranges. The length scales of ion dynamics, such as characteristic mean square displacement and spatial extent of sub-diffusive motion of lithium ions have been determined from the ac conductivity and dielectric spectra, respectively, in the framework of linear response theory. The relative concentrations of different network structural units have been determined from the deconvolution of the FTIR spectra. A direct correlation between the ion dynamics and the characteristic length scales and the relative concentration of BO{sub 4} units has been established for different compositions of the borotellurite glasses.
A. LUCCHETTI
2014-09-01
Full Text Available Passive nets are currently among the most important fishing gears largely used along the Mediterranean coasts by the small scale fisheries sector. The fishing effort exerted by this sector is strongly correlated with net dimensions. Therefore, the use of passive nets is worldwide managed by defining net length and net drop. The EC Reg. 1967/2006 reports that the length of bottom-set and drifting nets may be also defined considering their weight or volume; however, no practical suggestions for fisheries inspectors are yet available. Consequently, even if such technical measures are reasonable from a theoretical viewpoint, they are hardly suitable as a management tool, due to the difficulties in harbour control. The overall objective of this paper is to provide a quick methodological approach for the gross estimation of passive net length (by net type on the basis of net volume. The final goal is to support fisheries managers with suitable advice for enforcement and control purposes. The results obtained are important for the management of the fishing effort exerted by small scale fisheries. The methodology developed in this study should be considered as a first attempt to tackle the tangled problem of net length estimation that can be easily applied in other fisheries and areas in order to improve the precision of the models developed herein.
A. LUCCHETTI
2015-01-01
Full Text Available Passive nets are currently among the most important fishing gears largely used along the Mediterranean coasts by the small scale fisheries sector. The fishing effort exerted by this sector is strongly correlated with net dimensions. Therefore, the use of passive nets is worldwide managed by defining net length and net drop. The EC Reg. 1967/2006 reports that the length of bottom-set and drifting nets may be also defined considering their weight or volume; however, no practical suggestions for fisheries inspectors are yet available. Consequently, even if such technical measures are reasonable from a theoretical viewpoint, they are hardly suitable as a management tool, due to the difficulties in harbour control. The overall objective of this paper is to provide a quick methodological approach for the gross estimation of passive net length (by net type on the basis of net volume. The final goal is to support fisheries managers with suitable advice for enforcement and control purposes. The results obtained are important for the management of the fishing effort exerted by small scale fisheries. The methodology developed in this study should be considered as a first attempt to tackle the tangled problem of net length estimation that can be easily applied in other fisheries and areas in order to improve the precision of the models developed herein.
2013-03-01
polymer matrix composite materials display quite complex deformation and failure behavior under ballistic/blast impact loading conditions. This complexity is generally attributed to a number of factors such as (a) hierarchical/multi-length scale architecture of the material microstructure; (b) nonlinear, rate-dependent and often pressure-sensitive mechanical response; and (c) the interplay of various intrinsic phenomena and processes such as fiber twisting, interfiber friction/sliding, etc. Material models currently employed in the computational engineering
Francis A. Roesch
2017-09-01
Full Text Available The resilience of a National Forest Inventory and Monitoring sample design can sometimes depend upon the degree to which it can adapt to fluctuations in funding. If a budget reduction necessitates the observation of fewer plots per year, some practitioners weigh the problem as a tradeoff between reducing the total number of plots and measuring the original number of plots over a greater number of years. Here, we explore some of the effects of differing plot intensities and cycle lengths on variants of three general classes of estimators for annual cubic meter per hectare volume, using a simulated population and appropriately-graduated sampling simulations. The simulations showed that an increase in cycle length yielded quite dramatic effects while differences due to a simulated reduction in plot intensity had more subtle effects.
Aguiar, Jeffery A. [National Renewable Energy Laboratory, Golden CO 80401 USA; Erkan, Mehmet E. [Department of Electrical and Computer Engineering, University of Utah, UT 84112 USA; Pruzan, Dennis S. [Department of Materials Science and Engineering, University of Utah, UT 84112 USA; Nagaoka, Akira [Department of Materials Science and Engineering, University of Utah, UT 84112 USA; Department of Applied Physics and Electronic Engineering, University of Miyazaki, Miyazaki 889 2192 Japan; Yoshino, Kenji [Department of Applied Physics and Electronic Engineering, University of Miyazaki, Miyazaki 889 2192 Japan; Moutinho, Helio [National Renewable Energy Laboratory, Golden CO 80401 USA; Al-Jassim, Mowafak [National Renewable Energy Laboratory, Golden CO 80401 USA; Scarpulla, Michael A. [Department of Electrical and Computer Engineering, University of Utah, UT 84112 USA; Department of Materials Science and Engineering, University of Utah, UT 84112 USA
2016-04-05
Kesterite Cu_{2}ZnSn(S,Se)_{4} (CZTSSe) is a sustainable material for thin-film photovoltaics with device efficiencies greater than 12% have been demonstrated. Despite similar crystal structure and polycrystalline film microstructures, there is widespread evidence for larger-amplitude potential and bandgap fluctuations in CZTS than in the analogous Cu(In,Ga)Se_{2} (CIGSe) chalcopyrite material. This disorder is believed to account for a sizable part of the larger open-circuit voltage (VOC) deficit in CZTS devices, yet the detailed origins and length scales of these fluctuations have not been fully elucidated. Herein, we present a transmission electron microscopy study focusing on composition variation within bulk multicrystals of CZTS grown by the travelling heater method (THM). In these slow-cooled, solution grown crystals we find direct evidence for spatial composition fluctuations of amplitude <1 at.% (~5 x 10^{20} cm^{-3}) and thus, explainable by point defects. However, rather than being homogeneously-distributed we find a characteristic 20 nm length scale for these fluctuations, which sets a definite length scale for band gap and potential fluctuations. At Σ3 grain boundaries, we find no evidence of composition variation compared to the bulk. The finding highlights such variations reported at grain boundaries in polycrystalline thin-films are direct consequences of processing methods and not intrinsic properties of CZTS itself.
Bovy, Jo
2013-01-01
We present and apply rigorous dynamical modeling with which we infer unprecedented constraints on the stellar and dark matter mass distribution within our Milky Way (MW), based on large sets of phase-space data on individual stars. Specifically, we model the dynamics of 16,269 G-type dwarfs from SEGUE, which sample 5 < R/kpc < 12 and 0.3 < |Z|/kpc < 3. We independently fit a parameterized MW potential and a three-integral, action-based distribution function (DF) to the phase-space data of 43 separate abundance-selected sub-populations (MAPs), accounting for the complex selection effects affecting the data. We robustly measure the total surface density within 1.1 kpc of the mid-plane to about 5% over the range 4.5< R/kpc < 9. Using metal-poor MAPs with small radial scale lengths as dynamical tracers probes 4.5 < R/kpc < 7, while MAPs with longer radial scale lengths sample 7 < R/kpc < 9. We measure the mass-weighted Galactic disk scale length to be R_d = 2.15+/-0.14 kpc, in agreem...
P. Döll
2010-05-01
Full Text Available River flow regimes, including long-term average flows, seasonality, low flows, high flows and other types of flow variability, play an important role for freshwater ecosystems. Thus, climate change affects freshwater ecosystems not only by increased temperatures but also by altered river flow regimes. However, with one exception, transferable quantitative relations between flow alterations and ecological responses have not yet been derived. While discharge decreases are generally considered to be detrimental for ecosystems, the effect of future discharge increases is unclear. As a first step towards a global-scale analysis of climate change impacts on freshwater ecosystems, we quantified the impact of climate change on five ecologically relevant river flow indicators, using the global water model WaterGAP 2.1g to simulate monthly time series of river discharge with a spatial resolution of 0.5 degrees. Four climate change scenarios based on two global climate models and two greenhouse gas emissions scenarios were evaluated.
We compared the impact of climate change by the 2050s to the impact of water withdrawals and dams on natural flow regimes that had occurred by 2002. Climate change was computed to alter seasonal flow regimes significantly (i.e. by more than 10% on 90% of the global land area (excluding Greenland and Antarctica, as compared to only one quarter of the land area that had suffered from significant seasonal flow regime alterations due to dams and water withdrawals. Due to climate change, the timing of the maximum mean monthly river discharge will be shifted by at least one month on one third on the global land area, more often towards earlier months (mainly due to earlier snowmelt. Dams and withdrawals had caused comparable shifts on less than 5% of the land area only. Long-term average annual river discharge is predicted to significantly increase on one half of the land area, and to significantly decrease on one quarter
P. Döll
2010-02-01
Full Text Available River flow regimes, including long-term average flows, seasonality, low flows, high flows and other types of flow variability, play an important role for freshwater ecosystems. Thus, climate change affects freshwater ecosystems not only by increased temperatures but also by altered river flow regimes. However, with one exception, transferable quantitative relations between flow alterations and ecosystem responses have not yet been derived. While discharge decreases are generally considered to be detrimental for ecosystems, the effect of future discharge increases is unclear. As a first step towards a global-scale analysis of climate change impacts on freshwater ecosystems, we quantified the impact of climate change on five ecologically relevant river flow indicators, using the global water model WaterGAP 2.1g to simulate monthly time series of river discharge with a spatial resolution of 0.5 degrees. Four climate change scenarios based on two global climate models and two greenhouse gas emissions scenarios were evaluated.
We compared the impact of climate change by the 2050s to the impact of water withdrawals and dams on natural flow regimes that had occurred by 2002. Climate change was computed to alter seasonal flow regimes significantly (i.e. by more than 10% on 90% of the global land area (excluding Greenland and Antarctica, as compared to only one quarter of the land area that had suffered from significant seasonal flow regime alterations due to dams and water withdrawals. Due to climate change, the timing of the maximum mean monthly river discharge will be shifted by at least one month on one third on the global land area, more often towards earlier months (mainly due to earlier snowmelt. Dams and withdrawals had caused comparable shifts on less than 5% of the land area only. Long-term average annual river discharge is predicted to significantly increase on one half of the land area, and to significantly decrease on one quarter
Solodov, A. A.; Rosenberg, M. J.; Myatt, J. F.; Epstein, R.; Regan, S. P.; Seka, W.; Shaw, J.; Hohenberger, M.; Bates, J. W.; Moody, J. D.; Ralph, J. E.; Turnbull, D. P.; Barrios, M. A.
2016-05-01
The two-plasmon-decay (TPD) instability can be detrimental for direct-drive inertial confinement fusion because it generates high-energy electrons that can preheat the target, thereby reducing target performance. Hydrodynamic simulations to design a new experimental platform to investigate TPD and other laser-plasma instabilities relevant to direct-drive-ignition implosions at the National Ignition Facility are presented. The proposed experiments utilize planar plastic targets with an embedded Mo layer to characterize generation of hot electrons through Mo Kα fluorescence and hard x-ray emission. Different laser-irradiation geometries approximate conditions near both the equator and the pole of a polar-direct-drive implosion.
Vaingankar Janhavi
2011-10-01
Full Text Available Abstract Background Instruments to measure mental health and well-being are largely developed and often used within Western populations and this compromises their validity in other cultures. A previous qualitative study in Singapore demonstrated the relevance of spiritual and religious practices to mental health, a dimension currently not included in exiting multi-dimensional measures. The objective of this study was to develop a self-administered measure that covers all key and culturally appropriate domains of mental health, which can be applied to compare levels of mental health across different age, gender and ethnic groups. We present the item reduction and validation of the Positive Mental Health (PMH instrument in a community-based adult sample in Singapore. Methods Surveys were conducted among adult (21-65 years residents belonging to Chinese, Malay and Indian ethnicities. Exploratory and confirmatory factor analysis (EFA, CFA were conducted and items were reduced using item response theory tests (IRT. The final version of the PMH instrument was tested for internal consistency and criterion validity. Items were tested for differential item functioning (DIF to check if items functioned in the same way across all subgroups. Results: EFA and CFA identified six first-order factor structure (General coping, Personal growth and autonomy, Spirituality, Interpersonal skills, Emotional support, and Global affect under one higher-order dimension of Positive Mental Health (RMSEA = 0.05, CFI = 0.96, TLI = 0.96. A 47-item self-administered multi-dimensional instrument with a six-point Likert response scale was constructed. The slope estimates and strength of the relation to the theta for all items in each six PMH subscales were high (range:1.39 to 5.69, suggesting good discrimination properties. The threshold estimates for the instrument ranged from -3.45 to 1.61 indicating that the instrument covers entire spectrums for the six dimensions. The
Benjamin, Aaron S.; Tullis, Jonathan G.; Lee, Ji Hae
2013-01-01
Rating scales are a standard measurement tool in psychological research. However, research has suggested that the cognitive burden involved in maintaining the criteria used to parcel subjective evidence into ratings introduces "decision noise" and affects estimates of performance in the underlying task. There has been debate over whether…
Pal, Tamisra; Biswas, Ranjit
2015-12-24
Composition dependence of four-point dynamic susceptibilities, overlap functions, and other dynamic heterogeneity (DH) parameters have been investigated by using all-atom molecular dynamics simulations for aqueous solutions of the ionic liquid (IL), 1-octyl-3-methyl imidazolium tetrafluoroborate ([Omim][BF4]) covering the pure-to-pure range. Upon addition of water in the IL, the DH time scales become faster and the four-point dynamic susceptibility time scale softens. Evidences for jump motions for both water and ions have been found from the simulated single particle displacements that show strong deviation from Gaussian distribution. Estimated dynamic correlation length for water reflects effects of IL, whereas those for ions remain largely insensitive to the mixture composition. Simulated structural aspects and DH time scales provide microscopic explanations to the existing experimental observations from time-resolved fluorescence and Kerr spectroscopic measurements.
Seki Motoaki
2008-11-01
Full Text Available Abstract Background Thellungiella halophila (also known as Thellungiella salsuginea is a model halophyte with a small plant size, short life cycle, and small genome. It easily undergoes genetic transformation by the floral dipping method used with its close relative, Arabidopsis thaliana. Thellungiella genes exhibit high sequence identity (approximately 90% at the cDNA level with Arabidopsis genes. Furthermore, Thellungiella not only shows tolerance to extreme salinity stress, but also to chilling, freezing, and ozone stress, supporting the use of Thellungiella as a good genomic resource in studies of abiotic stress tolerance. Results We constructed a full-length enriched Thellungiella (Shan Dong ecotype cDNA library from various tissues and whole plants subjected to environmental stresses, including high salinity, chilling, freezing, and abscisic acid treatment. We randomly selected about 20 000 clones and sequenced them from both ends to obtain a total of 35 171 sequences. CAP3 software was used to assemble the sequences and cluster them into 9569 nonredundant cDNA groups. We named these cDNAs "RTFL" (RIKEN Thellungiella Full-Length cDNAs. Information on functional domains and Gene Ontology (GO terms for the RTFL cDNAs were obtained using InterPro. The 8289 genes assigned to InterPro IDs were classified according to the GO terms using Plant GO Slim. Categorical comparison between the whole Arabidopsis genome and Thellungiella genes showing low identity to Arabidopsis genes revealed that the population of Thellungiella transport genes is approximately 1.5 times the size of the corresponding Arabidopsis genes. This suggests that these genes regulate a unique ion transportation system in Thellungiella. Conclusion As the number of Thellungiella halophila (Thellungiella salsuginea expressed sequence tags (ESTs was 9388 in July 2008, the number of ESTs has increased to approximately four times the original value as a result of this effort. Our
Liao, S Y; Lu, C C; Chang, T; Huang, C F; Cheng, C H; Chang, L B
2014-08-01
Compared to AlGaN/GaN HEMT with 0.15 μm T-gate length, the AlInN/AlN/GaN one exhibits much higher current density and transconductance of 1558 mA/mm at Vd = 2 V and 330 mS/mm, respectively. The high extrinsic ft and fmax of 82 GHz and 70 GHz are extracted from AlInN/AlN/GaN HEMT. Besides, we find that the transconductance roll-off is significant in AlGaN/GaN, but largely improved in AlInN/AlN/GaN HEMT, suggesting that the high carrier density and lattice-matched epitaxial heterostructure is important to reach both large RF output power and high operation frequency, especially for an aggressively gate length scaling.
Gauzzi, A. [Ecole Polytechnique Federale, Lausanne (Switzerland). Dept. de Physique; Consiglio Nazionale delle Ricerche, Parma (Italy). Lab. MASPEC; Joensson-Aakerman, B.J.; Clerc-Dubois, A.; Pavuna, D. [Ecole Polytechnique Federale, Lausanne (Switzerland). Dept. de Physique
2000-09-15
Measurements of critical temperature T{sub c} in superconducting YBa{sub 2}Cu{sub 3}O{sub 6.9} films with reduced long-range structural order show the validity of the empirical scaling relation {delta}T{sub c}{proportional_to}r{sub c}{sup -2} between disorder-induced reduction of T{sub c} and structural coherence length r{sub c} in the ab-plane. This result is quantitatively explained by the disorder-induced confinement of the charge carriers within each ordered domain of size r{sub c}. Our analysis of the data based on this picture enables us to precisely determine the Ginzburg-Landau superconducting coherence length in the ab-plane, {xi}{sub ab} = 1.41 {+-} 0.04 nm. (orig.)
Length-displacement scaling of thrust faults on the Moon and the formation of uphill-facing scarps
Roggon, Lars; Hetzel, Ralf; Hiesinger, Harald; Clark, Jaclyn D.; Hampel, Andrea; van der Bogert, Carolyn H.
2017-08-01
Fault populations on terrestrial planets exhibit a linear relationship between their length, L, and the maximum displacement, D, which implies a constant D/L ratio during fault growth. Although it is known that D/L ratios of faults are typically a few percent on Earth and 0.2-0.8% on Mars and Mercury, the D/L ratios of lunar faults are not well characterized. Quantifying the D/L ratios of faults on the Moon is, however, crucial for a better understanding of lunar tectonics, including for studies of the amount of global lunar contraction. Here, we use high-resolution digital terrain models to perform a topographic analysis of four lunar thrust faults - Simpelius-1, Morozov (S1), Fowler, and Racah X-1 - that range in length from 1.3 km to 15.4 km. First, we determine the along-strike variation of the vertical displacement from ≥ 20 topographic profiles across each fault. For measuring the vertical displacements, we use a method that is commonly applied to fault scarps on Earth and that does not require detrending of the profiles. The resulting profiles show that the displacement changes gradually along these faults' strike, with maximum vertical displacements ranging from 17 ± 2 m for Simpelius-1 to 192 ± 30 m for Racah X-1. Assuming a fault dip of 30° yields maximum total displacements (D) that are twice as large as the vertical displacements. The linear relationship between D and L supports the inference that lunar faults gradually accumulate displacement as they propagate laterally. For the faults we investigated, the D/L ratio is ∼2.3%, an order of magnitude higher than theoretical predictions for the Moon, but a value similar for faults on Earth. We also employ finite-element modeling and a Mohr circle stress analysis to investigate why many lunar thrust faults, including three of those studied here, form uphill-facing scarps. Our analysis shows that fault slip is preferentially initiated on planes that dip in the same direction as the topography, because
Phillips James
2010-01-01
Full Text Available Abstract This paper distinguishes between two different scales of medium range order, MRO, in non-crystalline SiO2: (1 the first is ~0.4 to 0.5 nm and is obtained from the position of the first sharp diffraction peak, FSDP, in the X-ray diffraction structure factor, S(Q, and (2 the second is ~1 nm and is calculated from the FSDP full-width-at-half-maximum FWHM. Many-electron calculations yield Si–O third- and O–O fourth-nearest-neighbor bonding distances in the same 0.4–0.5 nm MRO regime. These derive from the availability of empty Si dπ orbitals for back-donation from occupied O pπ orbitals yielding narrow symmetry determined distributions of third neighbor Si–O, and fourth neighbor O–O distances. These are segments of six member rings contributing to connected six-member rings with ~1 nm length scale within the MRO regime. The unique properties of non-crystalline SiO2 are explained by the encapsulation of six-member ring clusters by five- and seven-member rings on average in a compliant hard-soft nano-scaled inhomogeneous network. This network structure minimizes macroscopic strain, reducing intrinsic bonding defects as well as defect precursors. This inhomogeneous CRN is enabling for applications including thermally grown ~1.5 nm SiO2 layers for Si field effect transistor devices to optical components with centimeter dimensions. There are qualitatively similar length scales in nano-crystalline HfO2 and phase separated Hf silicates based on the primitive unit cell, rather than a ring structure. Hf oxide dielectrics have recently been used as replacement dielectrics for a new generation of Si and Si/Ge devices heralding a transition into nano-scale circuits and systems on a Si chip.
Starikov, Sergey V., E-mail: starikov@ihed.ras.ru; Pisarev, Vasily V. [Moscow Institute of Physics and Technology, Dolgoprudny 141700 (Russian Federation); Joint Institute for High Temperatures, Russian Academy of Sciences, Moscow 125412 (Russian Federation)
2015-04-07
In this work, the femtosecond laser pulse modification of surface is studied for aluminium (Al) and gold (Au) by use of two-temperature atomistic simulation. The results are obtained for various atomistic models with different scales: from pseudo-one-dimensional to full-scale three-dimensional simulation. The surface modification after laser irradiation can be caused by ablation and melting. For low energy laser pulses, the nanoscale ripples may be induced on a surface by melting without laser ablation. In this case, nanoscale changes of the surface are due to a splash of molten metal under temperature gradient. Laser ablation occurs at a higher pulse energy when a crater is formed on the surface. There are essential differences between Al ablation and Au ablation. In the first step of shock-wave induced ablation, swelling and void formation occur for both metals. However, the simulation of ablation in gold shows an additional athermal type of ablation that is associated with electron pressure relaxation. This type of ablation takes place at the surface layer, at a depth of several nanometers, and does not induce swelling.
Shen Yi
2013-01-01
In this paper,we propose an adaptive strategy based on the linear prediction of queue length to minimize congestion in Barabási-Albert (BA) scale-free networks.This strategy uses local knowledge of traffic conditions and allows nodes to be able to self-coordinate their accepting probability to the incoming packets.We show that the strategy can delay remarkably the onset of congestion and systems avoiding the congestion can benefit from hierarchical organization of accepting rates of nodes.Furthermore,with the increase of prediction orders,we achieve larger values for the critical load together with a smooth transition from free-flow to congestion.
Lidorikis, Elefterios; Bachlechner, Martina E.; Kalia, Rajiv K.; Nakano, Aiichiro; Vashishta, Priya; Voyiadjis, George Z.
2001-08-01
A hybrid molecular-dynamics (MD) and finite-element simulation approach is used to study stress distributions in silicon/silicon-nitride nanopixels. The hybrid approach provides atomistic description near the interface and continuum description deep into the substrate, increasing the accessible length scales and greatly reducing the computational cost. The results of the hybrid simulation are in good agreement with full multimillion-atom MD simulations: atomic structures at the lattice-mismatched interface between amorphous silicon nitride and silicon induce inhomogeneous stress patterns in the substrate that cannot be reproduced by a continuum approach alone.
Okaya, D.; Johnson, S. E.; Vel, S. S.; Song, W. J.; Christensen, N. I.
2012-04-01
Recent studies based on laboratory petrophysics and in particular EBSD-based calculations indicate material rock anisotropy for crustal rocks can possess significant low orders of symmetry. These symmetries based on elastic tensor calculations can range from hexagonal and orthorhombic down to monoclinic and triclinic. On the other hand, interpretation of field seismic data yield crustal anisotropy of fast- or slow-axis transverse isotropy (hexagonal) symmetry at best; identification of orthorhombic symmetry is barely possible. Seismic results are often limited to simple orientations of the symmetry axes, such as vertical (radial anisotropy) or horizontal (azimuthal anisotropy). The physical scales of earth anisotropic fabrics and of seismic waves affect the types of information that may be extracted from seismic signals. A seismic wave has inherent limits to resolving capabilities, usually measured as some percentage of its wavelength, λ. This wave will accumulate anisotropic signal in two ways based on its path through anisotropic media of physical size, L: (1) When the wave is much smaller than the anisotropic material (λ > L), the wave will not see details of the material but will respond to just the bulk average of the material. In the first case, the wave will be sensitive to large scale earth changes such as limbs of an antiformal mountain range. The accumulating anisotropic seismic signal can get complicated (e.g., shear wave splits of splits). In the second case, the wave is too large to see any fine detail, and the material can be represented by an equivalent "effective media" that produces the same seismic response. Geometrical structure is a factor that helps bridge the scales of rock CPO to lower resolution seismic signals. Local rock CPO can fill or be mapped into a structure that is large enough for a seismic wave to respond to. We use tensor representation of anisotropic elasticity to formulate a way to separate structural effects from local rock
Kumar, K; Liu, G; Nogami, J; Kherani, N P
2016-01-01
In this paper, we simulate a front surface inverted pyramidal grating texture on 2 to 400 micron thick silicon and optimize it to derive maximum photocurrent density from the cell. We identify a one size fits all front grating period of 1000 nm that leads to maximum photo-absorption of normally incident AM1.5g solar spectrum in silicon (configured with a back surface reflector) irrespective of the thickness of the crystalline silicon absorbing layer. With the identification of such universally optimized periodicity for the case of an inverted pyramidal grating texture, a common fabrication process can be designed to manufacture high-efficiency devices on crystalline silicon regardless of wafer thickness. In order to validate the results of the simulation, we fabricated high resolution inverted pyramidal textures on a 400 micron thick silicon wafer with electron beam lithography to compare the reflectance from submicron and wavelength scale periodic textures. The experimental reflectance measurements on textur...
Scaling between localization length and {Tc} in disordered YBa{sub 2}Cu{sub 3}O{sub 6.9}
Gauzzi, A.; Pavuna, D.
1999-12-20
The authors quantitatively study the effect of growth-induced reduction of long range structural order on the superconducting transition in epitaxial YBa{sub 2}Cu{sub 3}O{sub 6.9} films. The corresponding reduction of structural coherence length r{sub c} is determined from the width of X-ray diffraction rocking curves. {Tc} measurements in the films give evidence for the validity of the empirical scaling relation {Delta}{Tc} {approximately} r{sub c,ab}{sup {minus}2}, where {Delta}{Tc} is the disorder-induced reduction of {Tc} and r{sub c,ab} is the structural coherence length in the ab-plane. To explain this algebraic law the authors propose a simple phenomenological model based on the disorder-induced localization of the charge carriers within each ordered domain of size r{sub c,ab}. This picture enables them to precisely determine the Ginzburg-Landau superconducting coherence length in the ab-plane, and they obtain {xi}{sub ab} = 1.41 {+-} 0.04 nm.
Aprile, Carmela; Corma, Avelino; Garcia, Hermenegildo
2008-02-14
This review summarizes the physical approaches towards enhancement of the photocatalytic activity of titanium dioxide by controlling this semiconductor in a certain length scale from subnanometric to submillimetric distances and provides examples in which the photocatalytic activity of TiO2 is not promoted by doping or changes in the chemical composition, but rather by application of physical concepts and spatial structuring of the semiconductor. Thus, encapsulation inside the micropores and cavities of zeolites (about 1 nm) renders small titanium oxide clusters with harnessed photocatalytic activity. On the other hand, nanometric titanium particles can be ordered forming structured periodic mesoporous materials with high specific surface area and well defined porosity. Titiania nanotubes of micrometric length, either independent or forming a membrane, also exhibit unique photocatalytic activity as consequence of the long diffusion length of charge carriers along the nanotube axis. Finally, photonic crystals with an inverse opal structure and the even more powerful concept of photonic sponges can serve to slow down visible light photons inside the material, increasing the effective optical path in such a way that light absorption near the absorption onset of the material is enhanced considerably. All these physical-based approaches have shown their potential in enhancing the photocatalytic activity of titania, paving the way for a new generation of novel structured photocatalysts in which physical and chemical concepts are combined.
Bensby, T; Oey, M S; Yong, D; Meléndez, J
2011-01-01
Based on high-resolution spectra obtained with the MIKE spectrograph on the Magellan telescopes we present detailed elemental abundances for 20 red giant stars in the outer Galactic disk, located at Galactocentric distances between 9 and 13 kpc. The outer disk sample is complemented with samples of red giants from the inner Galactic disk and the solar neighbourhood, analysed using identical methods. For Galactocentric distances beyond 10 kpc, we only find chemical patterns associated with the local thin disk, even for stars far above the Galactic plane. Our results show that the relative densities of the thick and thin disks are dramatically different from the solar neighbourhood, and we therefore suggest that the radial scale length of the thick disk is much shorter than that of the thin disk. We make a first estimate of the thick disk scale-length of L_thick=2.0 kpc, assuming L_thin=3.8 kpc for the thin disk. We suggest that radial migration may explain the lack of radial age, metallicity, and abundance gra...
V. Martinez-Quiroga
2014-01-01
Full Text Available System codes along with necessary nodalizations are valuable tools for thermal hydraulic safety analysis. Qualifying both codes and nodalizations is an essential step prior to their use in any significant study involving code calculations. Since most existing experimental data come from tests performed on the small scale, any qualification process must therefore address scale considerations. This paper describes the methodology developed at the Technical University of Catalonia in order to contribute to the qualification of Nuclear Power Plant nodalizations by means of scale disquisitions. The techniques that are presented include the so-called Kv-scaled calculation approach as well as the use of “hybrid nodalizations” and “scaled-up nodalizations.” These methods have revealed themselves to be very helpful in producing the required qualification and in promoting further improvements in nodalization. The paper explains both the concepts and the general guidelines of the method, while an accompanying paper will complete the presentation of the methodology as well as showing the results of the analysis of scaling discrepancies that appeared during the posttest simulations of PKL-LSTF counterpart tests performed on the PKL-III and ROSA-2 OECD/NEA Projects. Both articles together produce the complete description of the methodology that has been developed in the framework of the use of NPP nodalizations in the support to plant operation and control.
Peyre, Véronique; Bouguerra, Sabah; Testard, Fabienne
2013-01-01
The micellization in mixed solvent was studied using conductimetry, density measurements (molar volumes), and small angle neutron scattering (SANS) to explore dodecyltrimethylammonium bromide (DTABr) micelle formation throughout the entire composition range of water-dimethylsulfoxide (DMSO) mixtures. As the concentration of DMSO was increased in the mixture, the critical micelle concentration (CMC) increased, the aggregation number decreased and the ionization degree increased, until no aggregates could be detected any more for DMSO molar fraction higher than 0.51. The results were consistent with the presence of globular micelles interacting via a coulombic potential. The experimental CMC values and aggregation numbers were successfully reconciled with a molecular thermodynamic model describing the micellization process in solvent mixtures (R. Nagarajan and C.-C. Wang, Langmuir 16 (2000) 5242). The structural and thermodynamic characterization of the micelles agreed with the prediction of a dissymmetric solvation of the surfactant entity: the hydrocarbon chain was surrounded only by DMSO while the polar head was surrounded only by water. The decrease in the ionization degree was due to the condensation of the counterions and was definitely linked to the geometrical characteristics of the aggregates and by no means to the CMC or salinity. This multi-technique study provides new insight into the role of solvation in micellization and the reason for the decrease in ionization degree, emphasizing the dissymmetric solvation of the chain by DMSO and the head by water. This is the first time that, for a given surfactant in solvent mixtures, micellization is described using combined analysis from molecular to macroscopic scale.
Radulescu, Aurel; Szekely, Noemi Kinga; Appavou, Marie-Sousai; Pipich, Vitaliy; Kohnke, Thomas; Ossovyi, Vladimir; Staringer, Simon; Schneider, Gerald J.; Amann, Matthias; Zhang-Haagen, Bo; Brandl, Georg; Drochner, Matthias; Engels, Ralf; Hanslik, Romuald; Kemmerling, Günter
2016-01-01
The KWS-2 SANS diffractometer is dedicated to the investigation of soft matter and biophysical systems covering a wide length scale, from nm to µm. The instrument is optimized for the exploration of the wide momentum transfer Q range between 1x10-4 and 0.5 Å-1 by combining classical pinhole, focusing (with lenses), and time-of-flight (with chopper) methods, while simultaneously providing high-neutron intensities with an adjustable resolution. Because of its ability to adjust the intensity and the resolution within wide limits during the experiment, combined with the possibility to equip specific sample environments and ancillary devices, the KWS-2 shows a high versatility in addressing the broad range of structural and morphological studies in the field. Equilibrium structures can be studied in static measurements, while dynamic and kinetic processes can be investigated over time scales between minutes to tens of milliseconds with time-resolved approaches. Typical systems that are investigated with the KWS-2 cover the range from complex, hierarchical systems that exhibit multiple structural levels (e.g., gels, networks, or macro-aggregates) to small and poorly-scattering systems (e.g., single polymers or proteins in solution). The recent upgrade of the detection system, which enables the detection of count rates in the MHz range, opens new opportunities to study even very small biological morphologies in buffer solution with weak scattering signals close to the buffer scattering level at high Q. In this paper, we provide a protocol to investigate samples with characteristic size levels spanning a wide length scale and exhibiting ordering in the mesoscale structure using KWS-2. We present in detail how to use the multiple working modes that are offered by the instrument and the level of performance that is achieved. PMID:28060296
Radulescu, Aurel; Szekely, Noemi Kinga; Appavou, Marie-Sousai; Pipich, Vitaliy; Kohnke, Thomas; Ossovyi, Vladimir; Staringer, Simon; Schneider, Gerald J; Amann, Matthias; Zhang-Haagen, Bo; Brandl, Georg; Drochner, Matthias; Engels, Ralf; Hanslik, Romuald; Kemmerling, Günter
2016-12-08
The KWS-2 SANS diffractometer is dedicated to the investigation of soft matter and biophysical systems covering a wide length scale, from nm to µm. The instrument is optimized for the exploration of the wide momentum transfer Q range between 1x10(-4) and 0.5 Å(-1) by combining classical pinhole, focusing (with lenses), and time-of-flight (with chopper) methods, while simultaneously providing high-neutron intensities with an adjustable resolution. Because of its ability to adjust the intensity and the resolution within wide limits during the experiment, combined with the possibility to equip specific sample environments and ancillary devices, the KWS-2 shows a high versatility in addressing the broad range of structural and morphological studies in the field. Equilibrium structures can be studied in static measurements, while dynamic and kinetic processes can be investigated over time scales between minutes to tens of milliseconds with time-resolved approaches. Typical systems that are investigated with the KWS-2 cover the range from complex, hierarchical systems that exhibit multiple structural levels (e.g., gels, networks, or macro-aggregates) to small and poorly-scattering systems (e.g., single polymers or proteins in solution). The recent upgrade of the detection system, which enables the detection of count rates in the MHz range, opens new opportunities to study even very small biological morphologies in buffer solution with weak scattering signals close to the buffer scattering level at high Q. In this paper, we provide a protocol to investigate samples with characteristic size levels spanning a wide length scale and exhibiting ordering in the mesoscale structure using KWS-2. We present in detail how to use the multiple working modes that are offered by the instrument and the level of performance that is achieved.
Miller, Joshua D.; Price, Joanna; Campbell, W. Keith
2012-01-01
Some scholars have called for the replacement of the Narcissistic Personality Inventory (NPI) with more narrow scales measuring grandiosity and entitlement instead. In the current study, the authors examined the relations among the NPI and measures of grandiosity and entitlement, as well as in relation to a measure of the Five-Factor Model (FFM).…
Ortiz-Iniesta, Maria Jesus; Melian-Cabrera, Ignacio
2015-01-01
A mild template removal of microcrystalline beta zeolite, based on Fenton chemistry, was optimized. Fenton detemplation was studied in terms of applicability conditions window, reaction rate and scale up. TGA and CHN elemental analysis were used to evaluate the detemplation effectiveness, while 'CP,
Monteiro, PMS
2006-09-01
Full Text Available or mortality of rock lobster in the southern Benguela; Medium term (2 month) forecasting of the intensification of the remote forcing of ETSA derived LOW which has a bearing on the Namibian hake fishery These two scales are discussed in detail in the companion...
A Multiscale Lattice-Boltzmann Model of Macro-to-Micro Scale Transport Relevant to Gut Function
Wang, Yanxing; Brasseur, James; Banco, Gino
2007-11-01
Nutrient and pharmaceutical absorption in the small intestine involve coupled multiscale transport and mixing processes that span several orders of magnitude. We hypothesize that muscle-induced villi motions generate and control a ``micro-mixing layer'' that couples with macro-scale mixing to enhance molecular transport to and from the epithelium. In this work we developed a 2-D numerical method based on a multigrid strategy within the lattice-Boltzmann framework. We model a macro-scale cavity flow with microscale finger-like villi in pendular motion on the lower surface and evaluate the coupling between macro and micro-scale fluid motions, scalar mixing, and uptake of passive scalar at the villi surface. Preliminary results show that the moving villi can be effective mixers at the micro scale, especially when groups of villi move in a coordinated, but out-of-phase fashion. A time-evolving series of flow recirculation eddies are generated within a micro mixing layer that increase transport of passive scalar from the macro eddy to the surface by advection. Flow parameters such as frequency of pendular motion, spacing between villi and villi grouping, have strong influences on the behaviors of the micro-mixing layer and the efficiency of scalar transport. An extensive analysis is in process to quantify correlation between scalar mixing and flux, details of villi motion, and induced flow patterns.
Miller, Joshua D.; Price, Joanna; Campbell, W. Keith
2012-01-01
Some scholars have called for the replacement of the Narcissistic Personality Inventory (NPI) with more narrow scales measuring grandiosity and entitlement instead. In the current study, the authors examined the relations among the NPI and measures of grandiosity and entitlement, as well as in relation to a measure of the Five-Factor Model (FFM).…
Zhang, Yongfeng [Idaho National Laboratory
2016-09-01
U3Si2 and FeCrAl have been proposed as fuel and cladding concepts, respectively, for accident tolerance fuels with higher tolerance to accident scenarios compared to UO2. However, a lot of key physics and material properties regarding their in-pile performance are yet to be explored. To accelerate the understanding and reduce the cost of experimental studies, multiscale modeling and simulation are used to develop physics-based materials models to assist engineering scale fuel performance modeling. In this report, the lower-length-scale efforts in method and material model development supported by the Accident Tolerance Fuel (ATF) high-impact-problem (HIP) under the NEAMS program are summarized. Significant progresses have been made regarding interatomic potential, phase field models for phase decomposition and gas bubble formation, and thermal conductivity for U3Si2 fuel, and precipitation in FeCrAl cladding. The accomplishments are very useful by providing atomistic and mesoscale tools, improving the current understanding, and delivering engineering scale models for these two ATF concepts.
Philip Coppens
2015-03-01
Full Text Available A number of examples illustrate structural-dynamics studies of picosecond and slower photo-induced processes. They include molecular rearrangements and excitations. The information that can be obtained from such studies is discussed. The results are complementary to the information obtained from femtosecond studies. The point is made that all pertinent time scales should be covered to obtain comprehensive insight in dynamic processes of chemical and biological importance.
Suetsugu, Yoshitaka; Futahashi, Ryo; Kanamori, Hiroyuki; Kadono-Okuda, Keiko; Sasanuma, Shun-ichi; Narukawa, Junko; Ajimura, Masahiro; Jouraku, Akiya; Namiki, Nobukazu; Shimomura, Michihiko; Sezutsu, Hideki; Osanai-Futahashi, Mizuko; Suzuki, Masataka G; Daimon, Takaaki; Shinoda, Tetsuro; Taniai, Kiyoko; Asaoka, Kiyoshi; Niwa, Ryusuke; Kawaoka, Shinpei; Katsuma, Susumu; Tamura, Toshiki; Noda, Hiroaki; Kasahara, Masahiro; Sugano, Sumio; Suzuki, Yutaka; Fujiwara, Haruhiko; Kataoka, Hiroshi; Arunkumar, Kallare P; Tomar, Archana; Nagaraju, Javaregowda; Goldsmith, Marian R; Feng, Qili; Xia, Qingyou; Yamamoto, Kimiko; Shimada, Toru; Mita, Kazuei
2013-09-01
The establishment of a complete genomic sequence of silkworm, the model species of Lepidoptera, laid a foundation for its functional genomics. A more complete annotation of the genome will benefit functional and comparative studies and accelerate extensive industrial applications for this insect. To realize these goals, we embarked upon a large-scale full-length cDNA collection from 21 full-length cDNA libraries derived from 14 tissues of the domesticated silkworm and performed full sequencing by primer walking for 11,104 full-length cDNAs. The large average intron size was 1904 bp, resulting from a high accumulation of transposons. Using gene models predicted by GLEAN and published mRNAs, we identified 16,823 gene loci on the silkworm genome assembly. Orthology analysis of 153 species, including 11 insects, revealed that among three Lepidoptera including Monarch and Heliconius butterflies, the 403 largest silkworm-specific genes were composed mainly of protective immunity, hormone-related, and characteristic structural proteins. Analysis of testis-/ovary-specific genes revealed distinctive features of sexual dimorphism, including depletion of ovary-specific genes on the Z chromosome in contrast to an enrichment of testis-specific genes. More than 40% of genes expressed in specific tissues mapped in tissue-specific chromosomal clusters. The newly obtained FL-cDNA sequences enabled us to annotate the genome of this lepidopteran model insect more accurately, enhancing genomic and functional studies of Lepidoptera and comparative analyses with other insect orders, and yielding new insights into the evolution and organization of lepidopteran-specific genes.
Reimann, Tommy
2017-01-09
This thesis is concerned with different generic types of vortex matter arising in the intermediate state of the type-I superconductor lead, the intermediate mixed state of the type-II superconductor niobium, and the helimagnetic phase of the compound manganese silicide. It is demonstrated and explained how a combination of i) the radiographic techniques neutron grating interferometry and neutron diffractive imaging with ii) scattering methods such as small-angle-neutron scattering and ultra-small-angle neutron scattering can provide novel insight into the bulk behavior of these vortex systems. By means of the used scattering methods, detailed information on the morphology of the vortex phases covering a length scale of 0.01 to 10 μm are obtained, while the radiographic approaches additionally map the spatial distribution of vortices within the sample. In particular, this thesis focuses on the strong influences of demagnetization, geometric barriers and pinning on the vortex configuration.
Castro, C
2004-01-01
We construct the Extended Relativity Theory in Born-Clifford-Phase spaces with an upper and lower length scales (infrared/ultraviolet cutoff). The invariance symmetry leads naturally to the real Clifford algebra Cl (2, 6, R ) and complexified Clifford Cl_C ( 4 ) algebra related to Twistors. We proceed with an extensive review of Smith's 8D model based on the Clifford algebra Cl ( 1 ,7) that reproduces at low energies the physics of the Standard Model and Gravity; including the derivation of all the coupling constants, particle masses, mixing angles, ....with high precision. Further results by Smith are discussed pertaining the interplay among Clifford, Jordan, Division and Exceptional Lie algebras within the hierarchy of dimensions D = 26, 27, 28 related to bosonic string, M, F theory. Two Geometric actions are presented like the Clifford-Space extension of Maxwell's Electrodynamics, Brandt's action related the 8D spacetime tangent-bundle involving coordinates and velocities (Finsler geometries) followed by a...
Choi, Jonathan W.; Li, Zhaodong; Black, Charles T.; Sweat, Daniel P.; Wang, Xudong; Gopalan, Padma
2016-06-01
In this work, we demonstrate the use of self-assembled thin films of the cylinder-forming block copolymer poly(4-tert-butylstyrene-block-2-vinylpyridine) to pattern high density features at the 10 nm length scale. This material's large interaction parameter facilitates pattern formation in single-digit nanometer dimensions. This block copolymer's accessible order-disorder transition temperature allows thermal annealing to drive the assembly of ordered 2-vinylpyridine cylinders that can be selectively complexed with the organometallic precursor trimethylaluminum. This unique chemistry converts organic 2-vinylpyridine cylinders into alumina nanowires with diameters ranging from 8 to 11 nm, depending on the copolymer molecular weight. Graphoepitaxy of this block copolymer aligns and registers sub-12 nm diameter nanowires to larger-scale rectangular, curved, and circular features patterned by optical lithography. The alumina nanowires function as a robust hard mask to withstand the conditions required for patterning the underlying silicon by plasma etching. We conclude with a discussion of some of the challenges that arise with using block copolymers for patterning at sub-10 nm feature sizes.In this work, we demonstrate the use of self-assembled thin films of the cylinder-forming block copolymer poly(4-tert-butylstyrene-block-2-vinylpyridine) to pattern high density features at the 10 nm length scale. This material's large interaction parameter facilitates pattern formation in single-digit nanometer dimensions. This block copolymer's accessible order-disorder transition temperature allows thermal annealing to drive the assembly of ordered 2-vinylpyridine cylinders that can be selectively complexed with the organometallic precursor trimethylaluminum. This unique chemistry converts organic 2-vinylpyridine cylinders into alumina nanowires with diameters ranging from 8 to 11 nm, depending on the copolymer molecular weight. Graphoepitaxy of this block copolymer aligns and
Zouaoui, J; Trunfio-Sfarghiu, A M; Brizuela, L; Piednoir, A; Maniti, O; Munteanu, B; Mebarek, S; Girard-Egrot, A; Landoulsi, A; Granjon, T
2017-09-09
Considering the importance of cellular mechanics in the birth and evolution of cancer towards increasingly aggressive stages, we compared nano-mechanical properties of non-tumoral (WPMY-1) and highly aggressive metastatic (PC-3) prostate cell lines both on cell aggregates, single cells, and membrane lipids. Cell aggregate rheological properties were analyzed during dynamic compression stress performed on a homemade rheometer. Single cell visco-elasticity measurements were performed by Atomic Force Microscopy using a cantilever with round tip on surface-attached cells. At a molecular level, the lateral diffusion coefficient of total extracted lipids deposited as a Langmuir monolayer on an air-water interface was measured by the FRAP technique. At cellular pellet scale, and at single cell scale, PC-3 cells were less stiff, less viscous, and thus more prone to deformation than the WPMY-1 control. Interestingly, stress-relaxation curves indicated a two-step response, which we attributed to a differential response coming from two cell elements, successively stressed. Both responses are faster for PC-3 cells. At a molecular scale, the dynamics of the PC-3 lipid extracts are also faster than that of WPMY-1 lipid extracts. As the evolution of cancer towards increasingly aggressive stages is accompanied by alterations both in membrane composition and in cytoskeleton dynamical properties, we attribute differences in viscoelasticity between PC-3 and WPMY-1 cells to modifications of both elements. A decrease in stiffness and a less viscous behavior may be one of the diverse mechanisms that cancer cells adopt to cope with the various physiological conditions that they encounter. Copyright © 2017 Elsevier B.V. All rights reserved.
Klöckner, Wolf; Gacem, Riad; Anderlei, Tibor; Raven, Nicole; Schillberg, Stefan; Lattermann, Clemens; Büchs, Jochen
2013-12-02
Among disposable bioreactor systems, cylindrical orbitally shaken bioreactors show important advantages. They provide a well-defined hydrodynamic flow combined with excellent mixing and oxygen transfer for mammalian and plant cell cultivations. Since there is no known universal correlation between the volumetric mass transfer coefficient for oxygen kLa and relevant operating parameters in such bioreactor systems, the aim of this current study is to experimentally determine a universal kLa correlation. A Respiration Activity Monitoring System (RAMOS) was used to measure kLa values in cylindrical disposable shaken bioreactors and Buckingham's π-Theorem was applied to define a dimensionless equation for kLa. In this way, a scale- and volume-independent kLa correlation was developed and validated in bioreactors with volumes from 2 L to 200 L. The final correlation was used to calculate cultivation parameters at different scales to allow a sufficient oxygen supply of tobacco BY-2 cell suspension cultures. The resulting equation can be universally applied to calculate the mass transfer coefficient for any of seven relevant cultivation parameters such as the reactor diameter, the shaking frequency, the filling volume, the viscosity, the oxygen diffusion coefficient, the gravitational acceleration or the shaking diameter within an accuracy range of +/- 30%. To our knowledge, this is the first kLa correlation that has been defined and validated for the cited bioreactor system on a bench-to-pilot scale.
Ejeckam, R.B.
1992-12-01
Small-scale foliation measurements in lengths of core from borehole WD-3 of Permit Area D of the Lac du Bonnet Batholith have defined five major mean orientation sets. They strike NW, N and NE. The orientations (strike to the left of the dip direction/dip) of these sets are as follows: Set I - 028/74 deg; II - 001/66 deg; III - 100/58 deg; IV - 076/83 deg; and V - 210/40 deg. The small-scale foliations were defined by different mineral types such as biotite crystals, plagioclase, mineral banding and quartz lenses. Well-developed biotite foliation is commonly present whenever well-developed plagioclase foliation exists, but as the strength of development weakens, the preferred orientations of plagioclase foliation do not correspond to those of biotite. It is also noted that the foliations appear to strike in directions orthogonal to the fractures in the fracture zones in the same depth interval. No significant change in foliation orientation was observed in Zones I to IV. Set V, however, whose mean orientation is 210/40 deg, is absent from the Zone IV interval, ranging from 872 to 905 m. (auth)
Utzat, Hendrik
2017-04-24
A key challenge in achieving control over photocurrent generation by bulk-heterojunction organic solar cells is understanding how the morphology of the active layer impacts charge separation and in particular the separation dynamics within molecularly intermixed donor-acceptor domains versus the dynamics between phase-segregated domains. This paper addresses this issue by studying blends and devices of the amorphous silicon-indacenodithiophene polymer SiIDT-DTBT and the acceptor PCBM. By changing the blend composition, we modulate the size and density of the pure and intermixed domains on the nanometer length scale. Laser spectroscopic studies show that these changes in morphology correlate quantitatively with the changes in charge separation dynamics on the nanosecond time scale and with device photocurrent densities. At low fullerene compositions, where only a single, molecularly intermixed polymer-fullerene phase is observed, photoexcitation results in a ∼ 30% charge loss from geminate polaron pair recombination, which is further studied via light intensity experiments showing that the radius of the polaron pairs in the intermixed phase is 3-5 nm. At high fullerene compositions (≥67%), where the intermixed domains are 1-3 nm and the pure fullerene phases reach ∼4 nm, the geminate recombination is suppressed by the reduction of the intermixed phase, making the fullerene domains accessible for electron escape.
Pugh, C.E.
2001-01-29
Numerous large-scale fracture experiments have been performed over the past thirty years to advance fracture mechanics methodologies applicable to thick-wall pressure vessels. This report first identifies major factors important to nuclear reactor pressure vessel (RPV) integrity under pressurized thermal shock (PTS) conditions. It then covers 20 key experiments that have contributed to identifying fracture behavior of RPVs and to validating applicable assessment methodologies. The experiments are categorized according to four types of specimens: (1) cylindrical specimens, (2) pressurized vessels, (3) large plate specimens, and (4) thick beam specimens. These experiments were performed in laboratories in six different countries. This report serves as a summary of those experiments, and provides a guide to references for detailed information.
Earth Data Analysis Center, University of New Mexico — Flame length was modeled using FlamMap, an interagency fire behavior mapping and analysis program that computes potential fire behavior characteristics. The tool...
Kraucunas, Ian P.; Clarke, Leon E.; Dirks, James A.; Hathaway, John E.; Hejazi, Mohamad I.; Hibbard, Kathleen A.; Huang, Maoyi; Jin, Chunlian; Kintner-Meyer, Michael C.W.; Kleese van Dam, Kerstin; Leung, Lai-Yung R.; Li, Hongyi; Moss, Richard H.; Peterson, Marty J.; Rice, Jennie S.; Scott, Michael J.; Thomson, Allison M.; Voisin, Nathalie; West, Tristram O.
2015-04-01
The Platform for Regional Integrated Modeling and Analysis (PRIMA) is an innovative modeling system developed at Pacific Northwest National Laboratory (PNNL) to simulate interactions among natural and human systems at scales relevant to regional decision making. PRIMA brings together state-of-the-art models of regional climate, hydrology, agriculture, socioeconomics, and energy systems using a flexible coupling approach. The platform can be customized to inform a variety of complex questions and decisions, such as the integrated evaluation of mitigation and adaptation options across a range of sectors. Research into stakeholder decision support needs underpins the platform's application to regional issues, including uncertainty characterization. Ongoing numerical experiments are yielding new insights into the interactions among human and natural systems on regional scales with an initial focus on the energy-land-water nexus in the upper U.S. Midwest. This paper focuses on PRIMA’s functional capabilities and describes some lessons learned to date about integrated regional modeling.
Sun, Genhou; Hu, Zeyong; Wang, Jiemin; Xie, Zhipeng; Lin, Yun; Huang, Fangfang
2016-07-01
The aerodynamic roughness length (z0m) is a crucial parameter in quantifying momentum, sensible and latent heat fluxes between land surface and atmosphere, and it depends greatly on spatial scales. This paper presents a tentative study on the upscaling analysis of z0m in the north Tibetan Plateau based on in situ data from eddy covariance (EC) and large aperture scintillometer (LAS) and leaf area index (LAI) of MODerate-resolution Imaging Spectroradiometer (MODIS) with 250 m and 2 km spatial resolutions. The comparison of z0m calculated from EC (z0m_EC) and LAS (z0m _LAS) data indicates that z0m at both scales has apparent seasonal variations and is in good agreement with the LAI result. However, z0m_LAS is higher than z0m_EC, which is attributed to the differences in roughness elements in their footprints. An upscaling relationship for z0m is developed with z0m_EC, z0m _LAS and LAI with 250 m spatial resolution of MODIS. In addition, an altitude correction factor is introduced into the vegetation height estimation equation because the cold environment in the north Tibetan Plateau, which is due to its high altitude, has a strong influence on vegetation height. The z0m retrieval with 250 m spatial resolution in the rain season is validated with z0m_EC at sites Nagqu/Amdo, Nagqu/MS3478 and Nagqu/NewD66, and the agreement is acceptable. The spatial distribution of z0m retrievals at small spatial scale in the north Tibetan Plateau from June to September 2012 shows that the z0m values are less than 0.015 m in most areas, with the exception of the area in the southeast part, where z0m reaches 0.025 m owing to low altitudes. The z0m retrievals at large spatial scale in the north Tibetan Plateau from June to September 2012 range from 0.015 to 0.065 m, and high values appear in the area with low altitudes. The spatial distribution and frequency statistics of z0m retrievals at both spatial scales reveal the influence of altitude and LAI on the z0m in the north Tibetan
Hallock, Michael J; Stone, John E; Roberts, Elijah; Fry, Corey; Luthey-Schulten, Zaida
2014-05-01
Simulation of in vivo cellular processes with the reaction-diffusion master equation (RDME) is a computationally expensive task. Our previous software enabled simulation of inhomogeneous biochemical systems for small bacteria over long time scales using the MPD-RDME method on a single GPU. Simulations of larger eukaryotic systems exceed the on-board memory capacity of individual GPUs, and long time simulations of modest-sized cells such as yeast are impractical on a single GPU. We present a new multi-GPU parallel implementation of the MPD-RDME method based on a spatial decomposition approach that supports dynamic load balancing for workstations containing GPUs of varying performance and memory capacity. We take advantage of high-performance features of CUDA for peer-to-peer GPU memory transfers and evaluate the performance of our algorithms on state-of-the-art GPU devices. We present parallel e ciency and performance results for simulations using multiple GPUs as system size, particle counts, and number of reactions grow. We also demonstrate multi-GPU performance in simulations of the Min protein system in E. coli. Moreover, our multi-GPU decomposition and load balancing approach can be generalized to other lattice-based problems.
Favali, Paolo; Beranzoli, Laura; Best, Mairi; Franceschini, PierLuigi; Materia, Paola; Peppoloni, Silvia; Picard, John
2014-05-01
EMSO (European Multidisciplinary Seafloor and Water Column Observatory) is a large-scale European Research Infrastructure (RI). It is a geographically distributed infrastructure composed of several deep-seafloor and water-column observatories, which will be deployed at key sites in European waters, spanning from the Arctic, through the Atlantic and Mediterranean, to the Black Sea, with the basic scientific objective of real-time, long-term monitoring of environmental processes related to the interaction between the geosphere, biosphere and hydrosphere. EMSO is one of the environmental RIs on the ESFRI roadmap. The ESRFI Roadmap identifies new RIs of pan-European importance that correspond to the long term needs of European research communities. EMSO will be the sub-sea segment of the EU's large-scale Earth Observation program, Copernicus (previously known as GMES - Global Monitoring for Environment and Security) and will significantly enhance the observational capabilities of European member states. An open data policy compliant with the recommendations being developed within the GEOSS initiative (Global Earth Observation System of Systems) will allow for shared use of the infrastructure and the exchange of scientific information and knowledge. The processes that occur in the oceans have a direct impact on human societies, therefore it is crucial to improve our understanding of how they operate and interact. To encompass the breadth of these major processes, sustained and integrated observations are required that appreciate the interconnectedness of atmospheric, surface ocean, biological pump, deep-sea, and solid-Earth dynamics and that can address: • natural and anthropogenic change; • interactions between ecosystem services, biodiversity, biogeochemistry, physics, and climate; • impacts of exploration and extraction of energy, minerals, and living resources; • geo-hazard early warning capability for earthquakes, tsunamis, gas-hydrate release, and slope
YU,KUI; BRINKER,C. JEFFREY; HURD,ALAN J.; EISENBERG,ADI
2000-11-22
Since the discovery of surfactant-templated silica by Mobil scientists in 1992, mesostructured silica has been synthesized in various forms including thin films, powders, particles, and fibers. In general, mesostructured silica has potential applications, such as in separation, catalysis, sensors, and fluidic microsystems. In respect to these potential applications, mesostructured silica in the form of thin films is perhaps one of the most promising candidates. The preparation of mesostructured silica films through preferential solvent evaporation-induced self-assembly (EISA) has recently received much attention in the laboratories. However, no amphiphile/silica films with reverse mesophases have ever been made through this EISA procedure. Furthermore, templates employed to date have been either surfactants or poly(ethylene oxide)-b-poly(propylene oxide)-b-poly(ethylene oxide) triblock copolymers, such as pluronic P-123, both of which are water-soluble and alcohol-soluble. Due to their relatively low molecular weight, the templated silica films with mesoscopic order have been limited to relatively small characteristic length scales. In the present communication, the authors report a novel synthetic method to prepare mesostructured amphiphilic/silica films with regular and reverse mesophases of large characteristic length scales. This method involves evaporation-induced self-assembly (EISA) of amphiphilic polystyrene-block-poly(ethylene oxide) (PS-b-PEO) diblock copolymers. In the present study, the PS-b-PEO diblocks are denoted as, for example, PS(215)-b-PEO(100), showing that this particular sample contains 215 S repeat units and 100 EO repeat units. This PS(215)-b-PEO(100) diblock possesses high molecular weight and does not directly mix with water or alcohol. To the authors knowledge, no studies have reported the use of water-insoluble and alcohol-insoluble amphiphilic diblocks as structure-directing agents in the synthesis of mesostructured silica films through
Schuna, John M; Peterson, Courtney M; Thomas, Diana M; Heo, Moonseong; Hong, Sangmo; Choi, Woong; Heymsfield, Steven B
2015-01-01
Adult body mass (MB) empirically scales as height (Ht) squared (MB ∝ Ht(2) ), but does regional body mass and body composition as a whole also scale as Ht(2) ? This question is relevant to a wide range of biological topics, including interpretation of body mass index (BMI). Dual-energy X-ray absorptiometry (DXA) was used to quantify regional body mass [head (MH), trunk, arms, and legs] and whole-body composition [fat, lean soft tissue (LST), and bone mineral content (BMC)] in non-Hispanic (NH) white, NH black, Mexican American, and Korean adults participating in the National Health and Nutrition Examination Survey (NHANES; n = 17,126) and Korean NHANES (n = 8,942). Regression models were developed to establish Ht scaling powers for each measured component with adjustments for age and adiposity. Exploratory analyses revealed a consistent scaling pattern across men and women of the four population groups: regional mass powers, head (∼0.8-1) body composition, LST (∼2.0-2.3) body mass scaled uniformly across the eight sex and population groups as Ht(∼2) , tall and short subjects differed in body shape (e.g., MH/MB ∝ Ht(-∼1) ) and composition. Adult human body shape and relative composition are a function of body size as represented by stature, a finding that reveals a previously unrecognized phenotypic heterogeneity as defined by BMI. These observations provide new pathways for exploring mechanisms governing the interrelations between adult stature, body morphology, biomechanics, and metabolism. © 2014 Wiley Periodicals, Inc.
Anadón, A., E-mail: anadonb@unizar.es; Lucas, I.; Morellón, L. [Instituto de Nanociencia de Aragón, Universidad de Zaragoza, E-50018 Zaragoza (Spain); Departamento de Física de la Materia Condensada, Universidad de Zaragoza, E-50009 Zaragoza (Spain); Ramos, R. [WPI Advanced Institute for Materials Research, Tohoku University, Sendai 980-8577 (Japan); Spin Quantum Rectification Project, ERATO, Japan Science and Technology Agency, Sendai 980-8577 (Japan); Algarabel, P. A. [Departamento de Física de la Materia Condensada, Universidad de Zaragoza, E-50009 Zaragoza (Spain); Instituto de Ciencia de Materiales de Aragón, Universidad de Zaragoza and Consejo Superior de Investigaciones Científicas, 50009 Zaragoza (Spain); Ibarra, M. R.; Aguirre, M. H. [Instituto de Nanociencia de Aragón, Universidad de Zaragoza, E-50018 Zaragoza (Spain); Departamento de Física de la Materia Condensada, Universidad de Zaragoza, E-50009 Zaragoza (Spain); Laboratorio de Microscopías avanzadas, Universidad de Zaragoza, 50018 Zaragoza (Spain)
2016-07-04
The dependence of Spin Seebeck effect (SSE) with the thickness of the magnetic materials is studied by means of incoherent thermal excitation. The SSE voltage signal in Fe{sub 3}O{sub 4}/Pt bilayer structure increases with the magnetic material thickness up to 100 nm, approximately, showing signs of saturation for larger thickness. This dependence is well described in terms of a spin current pumped in the platinum film by the magnon accumulation in the magnetic material. The spin current is generated by a gradient of temperature in the system and detected by the Pt top contact by means of inverse spin Hall effect. Calculations in the frame of the linear response theory adjust with a high degree of accuracy the experimental data, giving a thermal length scale of the magnon accumulation (Λ) of 17 ± 3 nm at 300 K and Λ = 40 ± 10 nm at 70 K.
Andersson, Anders David Ragnar [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Pastore, Giovanni [Idaho National Lab. (INL), Idaho Falls, ID (United States); Liu, Xiang-Yang [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Perriot, Romain Thibault [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Tonks, Michael [Idaho National Lab. (INL), Idaho Falls, ID (United States); Stanek, Christopher Richard [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)
2014-11-07
This report summarizes the development of new fission gas diffusion models from lower length scale simulations and assessment of these models in terms of annealing experiments and fission gas release simulations using the BISON fuel performance code. Based on the mechanisms established from density functional theory (DFT) and empirical potential calculations, continuum models for diffusion of xenon (Xe) in UO_{2} were derived for both intrinsic conditions and under irradiation. The importance of the large X_{eU3O} cluster (a Xe atom in a uranium + oxygen vacancy trap site with two bound uranium vacancies) is emphasized, which is a consequence of its high mobility and stability. These models were implemented in the MARMOT phase field code, which is used to calculate effective Xe diffusivities for various irradiation conditions. The effective diffusivities were used in BISON to calculate fission gas release for a number of test cases. The results are assessed against experimental data and future directions for research are outlined based on the conclusions.
km-length IBAD-MgO fabricated at 1 km/h by a large-scale IBAD system in Fujikura
Hanyu, S., E-mail: satrush@gmail.co [Fujikura Ltd., 1440, Mutsuzaki, Sakura, Chiba 285-8550 (Japan); Tashita, C.; Hanada, Y.; Hayashida, T.; Morita, K.; Sutoh, Y.; Igarashi, M.; Kakimoto, K.; Kutami, H.; Iijima, Y.; Saitoh, T. [Fujikura Ltd., 1440, Mutsuzaki, Sakura, Chiba 285-8550 (Japan)
2010-12-15
A large-scale IBAD system with the world largest ion source was employed to fabricate ion beam-assisted deposition (IBAD) MgO films. Finally, we successfully fabricated a 1 km-length IBAD-MgO film at a production rate of 1 km/h. We also studied pulsed laser deposited (PLD) CeO{sub 2} films directly on IBAD-MgO films. An observation at the interface between MgO and CeO{sub 2} films by a transmission electron microscope (TEM), showed that a CeO{sub 2} film was finely textured on an IBAD-MgO film though a lattice mismatch was large (28.5%). Then we fabricated PLD-GdBa{sub 2}Cu{sub 3}O{sub 7-x} (GdBCO) film on the CeO{sub 2}/MgO substrate. Critical currents (I{sub c}) and critical current density (J{sub c}) of the films were over 300 A and 3 MA/cm{sup 2} at 77 K, self-field.
Oh, Sang Young; Lee, Minho; Seo, Joon Beom; Kim, Namkug; Lee, Sang Min; Lee, Jae Seung; Oh, Yeon Mok
2017-01-01
A novel approach of size-based emphysema clustering has been developed, and the size variation and collapse of holes in emphysema clusters are evaluated at inspiratory and expiratory computed tomography (CT). Thirty patients were visually evaluated for the size-based emphysema clustering technique and a total of 72 patients were evaluated for analyzing collapse of the emphysema hole in this study. A new approach for the size differentiation of emphysema holes was developed using the length scale, Gaussian low-pass filtering, and iteration approach. Then, the volumetric CT results of the emphysema patients were analyzed using the new method, and deformable registration was carried out between inspiratory and expiratory CT. Blind visual evaluations of EI by two readers had significant correlations with the classification using the size-based emphysema clustering method (r-values of reader 1: 0.186, 0.890, 0.915, and 0.941; reader 2: 0.540, 0.667, 0.919, and 0.942). The results of collapse of emphysema holes using deformable registration were compared with the pulmonary function test (PFT) parameters using the Pearson's correlation test. The mean extents of low-attenuation area (LAA), E1 (size variation and collapse of emphysema holes may be useful for understanding the dynamic collapse of emphysema and its functional relation.
Grujicic, M.; Pandurangan, B.; Snipes, J. S.; Yen, C.-F.; Cheeseman, B. A.
2013-03-01
Fiber-reinforced polymer matrix composite materials display quite complex deformation and failure behavior under ballistic/blast impact loading conditions. This complexity is generally attributed to a number of factors such as (a) hierarchical/multi-length scale architecture of the material microstructure; (b) nonlinear, rate-dependent and often pressure-sensitive mechanical response; and (c) the interplay of various intrinsic phenomena and processes such as fiber twisting, interfiber friction/sliding, etc. Material models currently employed in the computational engineering analyses of ballistic/blast impact protective structures made of this type of material do not generally include many of the aforementioned aspects of the material dynamic behavior. Consequently, discrepancies are often observed between computational predictions and their experimental counterparts. To address this problem, the results of an extensive set of molecular-level computational analyses regarding the role of various microstructural/morphological defects on the Kevlar® fiber mechanical properties are used to upgrade one of the existing continuum-level material models for fiber-reinforced composites. The results obtained show that the response of the material is significantly affected as a result of the incorporation of microstructural effects both under quasi-static simple mechanical testing condition and under dynamic ballistic-impact conditions.
Lidorikis, Elefterios; Bachlechner, Martina E.; Kalia, Rajiv K.; Nakano, Aiichiro; Vashishta, Priya
2005-09-01
A hybrid atomistic-continuum simulation approach has been implemented to study strain relaxation in lattice-mismatched Si/Si3N4 nanopixels on a Si(111) substrate. We couple the molecular-dynamics (MD) and finite-element simulation approaches to provide an atomistic description near the interface and a continuum description deep into the substrate, increasing the accessible length scales and greatly reducing the computational cost. The results of the hybrid simulation are validated against full multimillion-atom MD simulations. We find that strain relaxation in Si/Si3N4 nanopixels may occur through the formation of a network of interfacial domain boundaries reminiscent of interfacial misfit dislocations. They result from the nucleation of domains of different interfacial bonding at the free edges and corners of the nanopixel, and subsequent to their creation they propagate inwards. We follow the motion of the domain boundaries and estimate a propagation speed of about ˜2.5×103m/s . The effects of temperature, nanopixel architecture, and film structure on strain relaxation are also investigated. We find: (i) elevated temperature increases the interfacial domain nucleation rates; (ii) a thin compliant Si layer between the film and the substrate plays a beneficial role in partially suppressing strain relaxation; and (iii) additional control over the interface morphology may be achieved by varying the film structure.
Cheng, Judy Y; Morrison, Heather L; Lee, Young Sun; Beers, Timothy C; Bizyaev, Dmitry; Harding, Paul; Malanushenko, Elena; Malanushenko, Viktor; Oravetz, Daniel; Pan, Kaike; Schlesinger, Katharine J; Schneider, Donald P; Simmons, Audrey; Weaver, Benjamin A
2012-01-01
We examine the \\alpha-element abundance ratio, [\\alpha/Fe], of 5620 stars, observed by the Sloan Extension for Galactic Understanding and Exploration survey in the region 6 kpc < R < 16 kpc, 0.15 kpc < |Z| < 1.5 kpc, as a function of Galactocentric radius R and distance from the Galactic plane |Z|. Our results show that the high-\\alpha\\ thick disk population has a short scale length (L_thick ~ 1.8 kpc) compared to the low-\\alpha population, which is typically associated with the thin disk. We find that the fraction of high-\\alpha\\ stars in the inner disk increases at large |Z|, and that high-\\alpha\\ stars lag in rotation compared to low-\\alpha\\ stars. In contrast, the fraction of high-\\alpha\\ stars in the outer disk is low at all |Z|, and high- and low-\\alpha\\ stars have similar rotational velocities up to 1.5 kpc from the plane. We interpret these results to indicate that different processes were responsible for the high-\\alpha\\ populations in the inner and outer disk. The high-\\alpha\\ population...
Sui, Tan; Landini, Gabriel; Korsunsky, Alexander M.
2011-10-01
High energy (>50keV) synchrotron X-ray scattering experiments were carried out on beamline I12 JEEP at the Diamond Light Source (DLS, Oxford, UK). Although a complete human tooth could be studied, in the present study attention was focused on coupons from the region of the Dentin-Enamel Junction (DEJ). Simultaneous high energy SAXS/WAXS measurements were carried out. Quantitative analysis of the results allows multiple length scale characterization of the nano-crystalline structure of dental tissues. SAXS patterns analysis provide insight into the mean thickness and orientation of hydroxyapatite particles, while WAXS (XRD) patterns allow the determination of the crystallographic unit cell parameters of the hydroxyapatite phase. It was found that the average particle thickness determined from SAXS interpretation varies as a function of position in the vicinity of the DEJ. Most mineral particles are randomly orientated within dentin, although preferred orientation emerges and becomes stronger on approach to the enamel. Within the enamel, texture is stronger than anywhere in the dentin, and the determination of lattice parameters can be accomplished by Pawley refinement of the multiple peak diffraction pattern. The results demonstrate the feasibility of using high energy synchrotron X-ray beams for the characterization of human dental tissues. This opens up the opportunity of studying thick samples (e.g., complete teeth) in complex sample environments (e.g., under saline solution). This opens new avenues for the application of high energy synchrotron X-ray scattering to dental research.
2013-01-01
Background The genetics and molecular biology of sesame has only recently begun to be studied even though sesame is an important oil seed crop. A high-density genetic map for sesame has not been published yet due to a lack of sufficient molecular markers. Specific length amplified fragment sequencing (SLAF-seq) is a recently developed high-resolution strategy for large-scale de novo SNP discovery and genotyping. SLAF-seq was employed in this study to obtain sufficient markers to construct a high-density genetic map for sesame. Results In total, 28.21 Gb of data containing 201,488,285 pair-end reads was obtained after sequencing. The average coverage for each SLAF marker was 23.48-fold in the male parent, 23.38-fold in the female parent, and 14.46-fold average in each F2 individual. In total, 71,793 high-quality SLAFs were detected of which 3,673 SLAFs were polymorphic and 1,272 of the polymorphic markers met the requirements for use in the construction of a genetic map. The final map included 1,233 markers on the 15 linkage groups (LGs) and was 1,474.87 cM in length with an average distance of 1.20 cM between adjacent markers. To our knowledge, this map is the densest genetic linkage map to date for sesame. 'SNP_only’ markers accounted for 87.51% of the markers on the map. A total of 205 markers on the map showed significant (P sesame. The map was constructed using an F2 population and the SLAF-seq approach, which allowed the efficient development of a large number of polymorphic markers in a short time. Results of this study will not only provide a platform for gene/QTL fine mapping, map-based gene isolation, and molecular breeding for sesame, but will also serve as a reference for positioning sequence scaffolds on a physical map, to assist in the process of assembling the sesame genome sequence. PMID:24060091
Zhang, Yanxin; Wang, Linhai; Xin, Huaigen; Li, Donghua; Ma, Chouxian; Ding, Xia; Hong, Weiguo; Zhang, Xiurong
2013-09-24
The genetics and molecular biology of sesame has only recently begun to be studied even though sesame is an important oil seed crop. A high-density genetic map for sesame has not been published yet due to a lack of sufficient molecular markers. Specific length amplified fragment sequencing (SLAF-seq) is a recently developed high-resolution strategy for large-scale de novo SNP discovery and genotyping. SLAF-seq was employed in this study to obtain sufficient markers to construct a high-density genetic map for sesame. In total, 28.21 Gb of data containing 201,488,285 pair-end reads was obtained after sequencing. The average coverage for each SLAF marker was 23.48-fold in the male parent, 23.38-fold in the female parent, and 14.46-fold average in each F2 individual. In total, 71,793 high-quality SLAFs were detected of which 3,673 SLAFs were polymorphic and 1,272 of the polymorphic markers met the requirements for use in the construction of a genetic map. The final map included 1,233 markers on the 15 linkage groups (LGs) and was 1,474.87 cM in length with an average distance of 1.20 cM between adjacent markers. To our knowledge, this map is the densest genetic linkage map to date for sesame. 'SNP_only' markers accounted for 87.51% of the markers on the map. A total of 205 markers on the map showed significant (P sesame. The map was constructed using an F2 population and the SLAF-seq approach, which allowed the efficient development of a large number of polymorphic markers in a short time. Results of this study will not only provide a platform for gene/QTL fine mapping, map-based gene isolation, and molecular breeding for sesame, but will also serve as a reference for positioning sequence scaffolds on a physical map, to assist in the process of assembling the sesame genome sequence.
Oh SY
2017-07-01
Full Text Available Sang Young Oh,1,* Minho Lee,1,* Joon Beom Seo,1,* Namkug Kim,1,2,* Sang Min Lee,1 Jae Seung Lee,3 Yeon Mok Oh3 1Department of Radiology, 2Department of Convergence Medicine, 3Department of Pulmonology, University of Ulsan College of Medicine, Asan Medical Center, Seoul, Republic of Korea *These authors contributed equally to this work Abstract: A novel approach of size-based emphysema clustering has been developed, and the size variation and collapse of holes in emphysema clusters are evaluated at inspiratory and expiratory computed tomography (CT. Thirty patients were visually evaluated for the size-based emphysema clustering technique and a total of 72 patients were evaluated for analyzing collapse of the emphysema hole in this study. A new approach for the size differentiation of emphysema holes was developed using the length scale, Gaussian low-pass filtering, and iteration approach. Then, the volumetric CT results of the emphysema patients were analyzed using the new method, and deformable registration was carried out between inspiratory and expiratory CT. Blind visual evaluations of EI by two readers had significant correlations with the classification using the size-based emphysema clustering method (r-values of reader 1: 0.186, 0.890, 0.915, and 0.941; reader 2: 0.540, 0.667, 0.919, and 0.942. The results of collapse of emphysema holes using deformable registration were compared with the pulmonary function test (PFT parameters using the Pearson’s correlation test. The mean extents of low-attenuation area (LAA, E1 (<1.5 mm, E2 (<7 mm, E3 (<15 mm, and E4 (≥15 mm were 25.9%, 3.0%, 11.4%, 7.6%, and 3.9%, respectively, at the inspiratory CT, and 15.3%, 1.4%, 6.9%, 4.3%, and 2.6%, respectively at the expiratory CT. The extents of LAA, E2, E3, and E4 were found to be significantly correlated with the PFT parameters (r=−0.53, −0.43, −0.48, and −0.25, with forced expiratory volume in 1 second (FEV1; −0.81, −0.62, −0.75, and
Wietsma, T. W.; Zhang, C.; Oostrom, M.; Grate, J. W.
2010-12-01
Capture and sequestration of anthropogenic CO2 in depleted oil and gas reservoirs, unminable coal seams and deep saline aquifer are being intensively studied as a promising strategy to mitigate CO2 emission into the atmosphere. Two critical research areas are trapping mechanisms and caprock sealing efficiency, which are controlled by interfacial processes at the fluid-fluid and fluid-rock interfaces. Fundamental understanding of capillary/viscous effects and host rock heterogeneity on trapping mechanisms and sealing efficiency can be gained through micromodel pore-scale displacement experiments. Experimental capabilities are being developed at the Environmental Molecular Sciences Lab (EMSL), Pacific Northwest National Laboratory (PNNL) to study coupled flow and reactive transport processes in complex systems at the pore-scale at relevant storage pressures and temperatures. This presentation highlights our strategies for design and construction of a unique high-pressure system for micromodel experimentation and a capability for visualizing dynamic interfacial processes using a solvatochromic dye under supercritical conditions. Preliminary results on displacement of brine by supercritical CO2 will be presented.
Gammel, P.L.; Barber, B.P.; Ramirez, A.P.
1999-01-01
The flux line form factor in small angle neutron scattering and transport data determines the superconducting length scares and critical fields in single crystal ErNi2B2C. For H parallel to c, the coherence length xi increases and the penetration depth lambda decreases when crossing T-N = 6.0 K, ...
Urien, N; Lebrun, J D; Fechner, L C; Uher, E; François, A; Quéau, H; Coquery, M; Chaumot, A; Geffard, O
2016-05-15
Kinetic models have become established tools for describing trace metal bioaccumulation in aquatic organisms and offer a promising approach for linking water contamination to trace metal bioaccumulation in biota. Nevertheless, models are based on laboratory-derived kinetic parameters, and the question of their relevance to predict trace metal bioaccumulation in the field is poorly addressed. In the present study, we propose to assess the capacity of kinetic models to predict trace metal bioaccumulation in gammarids in the field at a wide spatial scale. The field validation consisted of measuring dissolved Cd, Cu, Ni and Pb concentrations in the water column at 141 sites in France, running the models with laboratory-derived kinetic parameters, and comparing model predictions and measurements of trace metal concentrations in gammarids caged for 7 days to the same sites. We observed that gammarids poorly accumulated Cu showing the limited relevance of that species to monitor Cu contamination. Therefore, Cu was not considered for model predictions. In contrast, gammarids significantly accumulated Pb, Cd, and Ni over a wide range of exposure concentrations. These results highlight the relevance of using gammarids for active biomonitoring to detect spatial trends of bioavailable Pb, Cd, and Ni contamination in freshwaters. The best agreements between model predictions and field measurements were observed for Cd with 71% of good estimations (i.e. field measurements were predicted within a factor of two), which highlighted the potential for kinetic models to link Cd contamination to bioaccumulation in the field. The poorest agreements were observed for Ni and Pb (39% and 48% of good estimations, respectively). However, models developed for Ni, Pb, and to a lesser extent for Cd, globally underestimated bioaccumulation in caged gammarids. These results showed that the link between trace metal concentration in water and in biota remains complex, and underlined the limits of
Beltrame, Ludovica; Carbonin, Daniele; Galelli, Stefano; Castelletti, Andrea
2014-05-01
Population growth, water scarcity and climate change are three major factors making the understanding of variations in water availability increasingly important. Therefore, reliable medium-to-long range forecasts of streamflows are essential to the development of water management policies. To this purpose, recent modelling efforts have been dedicated to seasonal and inter-annual streamflow forecasts based on the teleconnection between "at-site" hydro-meteorological processes and low frequency climate fluctuations, such as El Niño Southern Oscillation (ENSO). This work proposes a novel procedure for first detecting the impact of ENSO on hydro-meteorological processes at the catchment scale, and then assessing the potential of ENSO indicators for building medium-to-long range statistical streamflow prediction models. Core of this procedure is the adoption of the Iterative Input variable Selection (IIS) algorithm that is employed to find the most relevant forcings of streamflow variability and derive predictive models based on the selected inputs. The procedure is tested on the Columbia (USA) and Williams (Australia) Rivers, where ENSO influence has been well-documented, and then adopted on the unexplored Red River basin (Vietnam). Results show that IIS outcomes on the Columbia and Williams Rivers are consistent with the results of previous studies, and that ENSO indicators can be effectively used to enhance the streamflow forecast models capabilities. The experiments on the Red River basin show that the ENSO influence is less pronounced, inducing little effects on the basin hydro-meteorological processes.
Relevant Criteria for Testing the Quality of Turbulence Models
Frandsen, Sten; Jørgensen, Hans E.; Sørensen, John Dalsgaard
2007-01-01
turbines when seeking wind characteristics that correspond to one blade and the entire rotor, respectively. For heights exceeding 50-60m the gust factor increases with wind speed. For heights larger the 60-80m, present assumptions on the value of the gust factor are significantly conservative, both for 3......Seeking relevant criteria for testing the quality of turbulence models, the scale of turbulence and the gust factor have been estimated from data and compared with predictions from first-order models of these two quantities. It is found that the mean of the measured length scales is approx. 10......% smaller than the IEC model, for wind turbine hub height levels. The mean is only marginally dependent on trends in time series. It is also found that the coefficient of variation of the measured length scales is about 50%. 3sec and 10sec pre-averaging of wind speed data are relevant for MW-size wind...
Andrade, H; Santos, J; Taylor, R
2013-06-01
The ecology of common snook Centropomus undecimalis in Amatique Bay, a tropical estuary in eastern Guatemala, was investigated and life-history traits were used to conduct a meta-analysis of the species from Florida to Brazil. The reproduction cycle of C. undecimalis in Amatique was strongly related to the precipitation cycle, with a lag of 2 months. Spawning occurred from April to November with a peak spawning after the onset of the summer rains. Protandric sex reversal occurred early in the dry season (December) before somatic recovery from spawning. The growth cycle preceded that of body condition by c. 1 month, and was out of phase with the reproductive cycle. Growth was fast, as many individuals reached >70% of the maximum observed total length (LT , 102 cm) after 3 years. Sex transition occurred within a relatively narrow LT range (70-79 cm), but over a wide range of ages, indicating plasticity in this respect. The meta-analysis indicated a latitudinal-temperature gradient in life-history traits, as well as different seasonal patterns relative to temperature and hydrographical cycles. Centropomus undecimalis from cooler winter waters (e.g. Florida) reach larger maximum LT and LT at sex change, as well as greater gonado-somatic indices and longer life spans. Further, increased fishing mortality results in younger age at sex reversal and male predominance in the populations compared. Recognition of large-scale biogeographic patterns in this important, but little studied, fish species helps in the formulation of management advice in other areas of its occurrence. © 2013 The Authors. Journal of Fish Biology © 2013 The Fisheries Society of the British Isles.
Micro- and meso-scale effects of forested terrain
Dellwik, Ebba; Mann, Jakob; Sogachev, Andrey
2011-01-01
. Deviations from the requirement of homogeneity are often the focus of micro-scale studies in forested areas. Yet, to explain the wind climate in the relevant height range for turbines, it is necessary to also account for the length scales that are important parameters for the meso-scale flow. These length...... scales are the height of the planetary boundary layer and the Monin-Obukhov length, which both are related to the energy balance of the surface. Examples of important micro- and meso-scale effects of forested terrain are shown using data and model results from recent and ongoing experiments. For micro...
D Rechem; S Latreche; C Gontrand
2009-03-01
In this paper, we study the effects of short channel on double gate MOSFETs. We evaluate the variation of the threshold voltage, the subthreshold slope, the leakage current and the drain-induced barrier lowering when channel length CH decreases. Further- more, quantum effects on the performance of DG-MOSFETs are addressed and discussed. We also study the influence of metal gate work function on the performance of nanoscale MOSFETs. We use a self-consistent Poisson–Schrödinger solver in two dimensions over the entire device. A good agreement with numerical simulation results is obtained.
Nielsen, Tine; Kreiner, Svend
2011-01-01
approach to item reduction based on results of graphical loglinear Rasch modeling (GLLRM) was designed. This approach was then used to reduce the number of items in the subscales of the R-D-LSI which had an item-length of more than seven items, thereby obtaining the Danish Self-Assessment Learning Styles......The Revised Danish Learning Styles Inventory (R-D-LSI) (Nielsen 2005), which is an adaptation of Sternberg- Wagner Thinking Styles Inventory (Sternberg, 1997), comprises 14 subscales, each measuring a separate learning style. Of these 14 subscales, 9 are eight items long and 5 are seven items long...
Martínez-Tossas, L. A. [Department of Mechanical Engineering, Johns Hopkins University, Baltimore 21218 MD USA; Churchfield, M. J. [National Renewable Energy Laboratory, Golden 80401 CO USA; Meneveau, C. [Department of Mechanical Engineering, Johns Hopkins University, Baltimore 21218 MD USA
2017-01-20
The actuator line model (ALM) is a commonly used method to represent lifting surfaces such as wind turbine blades within large-eddy simulations (LES). In the ALM, the lift and drag forces are replaced by an imposed body force that is typically smoothed over several grid points using a Gaussian kernel with some prescribed smoothing width e. To date, the choice of e has most often been based on numerical considerations related to the grid spacing used in LES. However, especially for finely resolved LES with grid spacings on the order of or smaller than the chord length of the blade, the best choice of e is not known. In this work, a theoretical approach is followed to determine the most suitable value of e, based on an analytical solution to the linearized inviscid flow response to a Gaussian force. We find that the optimal smoothing width eopt is on the order of 14%-25% of the chord length of the blade, and the center of force is located at about 13%-26% downstream of the leading edge of the blade for the cases considered. These optimal values do not depend on angle of attack and depend only weakly on the type of lifting surface. It is then shown that an even more realistic velocity field can be induced by a 2-D elliptical Gaussian lift-force kernel. Some results are also provided regarding drag force representation.
Aoki, Koh; Yano, Kentaro; Suzuki, Ayako; Kawamura, Shingo; Sakurai, Nozomu; Suda, Kunihiro; Kurabayashi, Atsushi; Suzuki, Tatsuya; Tsugane, Taneaki; Watanabe, Manabu; Ooga, Kazuhide; Torii, Maiko; Narita, Takanori; Shin-I, Tadasu; Kohara, Yuji; Yamamoto, Naoki; Takahashi, Hideki; Watanabe, Yuichiro; Egusa, Mayumi; Kodama, Motoichiro; Ichinose, Yuki; Kikuchi, Mari; Fukushima, Sumire; Okabe, Akiko; Arie, Tsutomu; Sato, Yuko; Yazawa, Katsumi; Satoh, Shinobu; Omura, Toshikazu; Ezura, Hiroshi; Shibata, Daisuke
2010-03-30
The Solanaceae family includes several economically important vegetable crops. The tomato (Solanum lycopersicum) is regarded as a model plant of the Solanaceae family. Recently, a number of tomato resources have been developed in parallel with the ongoing tomato genome sequencing project. In particular, a miniature cultivar, Micro-Tom, is regarded as a model system in tomato genomics, and a number of genomics resources in the Micro-Tom-background, such as ESTs and mutagenized lines, have been established by an international alliance. To accelerate the progress in tomato genomics, we developed a collection of fully-sequenced 13,227 Micro-Tom full-length cDNAs. By checking redundant sequences, coding sequences, and chimeric sequences, a set of 11,502 non-redundant full-length cDNAs (nrFLcDNAs) was generated. Analysis of untranslated regions demonstrated that tomato has longer 5'- and 3'-untranslated regions than most other plants but rice. Classification of functions of proteins predicted from the coding sequences demonstrated that nrFLcDNAs covered a broad range of functions. A comparison of nrFLcDNAs with genes of sixteen plants facilitated the identification of tomato genes that are not found in other plants, most of which did not have known protein domains. Mapping of the nrFLcDNAs onto currently available tomato genome sequences facilitated prediction of exon-intron structure. Introns of tomato genes were longer than those of Arabidopsis and rice. According to a comparison of exon sequences between the nrFLcDNAs and the tomato genome sequences, the frequency of nucleotide mismatch in exons between Micro-Tom and the genome-sequencing cultivar (Heinz 1706) was estimated to be 0.061%. The collection of Micro-Tom nrFLcDNAs generated in this study will serve as a valuable genomic tool for plant biologists to bridge the gap between basic and applied studies. The nrFLcDNA sequences will help annotation of the tomato whole-genome sequence and aid in tomato functional
Cummins, D.J.F.
1985-01-01
This thesis seeks to extend the search for the moral implications inherent in the development, possession, and the threatened use of physical/astrophysical processes and in current understandings of the evolution of the physical universe. The nature of normal/theological discussion will not be a primary concern although clearly some residual position that such discussion is meaningful is presupposed. Neither is the nature of science or the scientific method at issue. It is assumed that both theology and science have long since negotiated the confidence crises of adolescence, and have mustered the requisite self-esteem regarding their respective disciplines. The aim of this work is to present the concept of time scales as a relevant moral category. It investigates the use of this concept and its relationship to the other categories developed in the relevant scientific literature. The question is raised as to the validity of and the future of the concept of time scales as a common moral ground.
无
2001-01-01
The genome length is a fundamental feature of a species. This note outlined the general concept and estimation method of the physical and genetic length. Some formulae for estimating the genetic length were derived in detail. As examples, the genome genetic length of Pinus pinaster Ait. and the genetic length of chromosome Ⅵ of Oryza sativa L. were estimated from partial linkage data.
Emmons, Samuel; Acharya, Bijaya; Platter, Lucas
2017-01-01
For an ultracold heteronuclear mixture with a large positive interspecies scattering length and negligible intraspecies scattering length, we determine the three-body recombination rate as a function of collision energy using universal functions of a single scaling variable. We use the zero-range approximation and the Skorniakov -Ter-Martirosian equation to calculate these scaling functions for a range of collision energies. Further, we explore the effects that a nonzero temperature has on three-body recombination, as well as the effects of the formation of deep dimers, for experimentally relevant heteronuclear gases such as the 6Li-133Cs mixture. NSF Grant Nos. PHY-1516077 and PHY-1555030.
Eric Costello
2011-01-01
Full Text Available The shape of a cable hanging under its own weight and uniform horizontal tension between two power poles is a catenary. The catenary is a curve which has an equation defined by a hyperbolic cosine function and a scaling factor. The scaling factor for power cables hanging under their own weight is equal to the horizontal tension on the cable divided by the weight of the cable. Both of these values are unknown for this problem. Newton's method was used to approximate the scaling factor and the arc length function to determine the length of the cable. A script was written using the Python programming language in order to quickly perform several iterations of Newton's method to get a good approximation for the scaling factor.
陈星明; 肖正学; 谭诚; 尹轶东
2012-01-01
Achieve higher efficiency is a aim of mining enterprises on the basis of safety produce, choice of the blasting method is an important restraining factor about mining costs. The deficiencies of medium-length hole blasting in small-scale and opencast quarry of Mianyang area were analyzed and pointed out by detailed survey. The suitable method of medium-length hole blasting in small-scale and opencast quarry of Mianyang area were designed according to deposit condition of mine and production status. It achieved good results on safe production and economic efficiency by carrying out the design. The optimization design can promote and improve small Small-scale and opencast quarry safety in production and economy efficiency.%钻孔爆破方式的选择是采矿成本高低的一个重要制约因素:通过调研绵阳地区部分小型露天采石场使用的中深孔爆破的方案,分析并指出其在爆破质量、生产安全性能和效率方面存在的不足之处,根据矿体赋存条件和实际生产状况对该中深孔爆破方案进行了重新设计,并进行了矿山现场实践,在安全生产和经济效果方面取得了良好的效果.研究成果可用于小型采石场.
Information, polarization and term length in democracy
Schultz, Christian
2008-01-01
This paper considers term lengths in a representative democracy where the political issue divides the population on the left-right scale. Parties are ideologically different and better informed about the consequences of policies than voters are. A short term length makes the government more accou...... the uncertainty is large and parties are not very polarized. Partisan voters always prefer a long term length. When politicians learn while in office a long term length becomes more attractive for swing voters....
Bovy, Jo [Institute for Advanced Study, Einstein Drive, Princeton, NJ 08540 (United States); Rix, Hans-Walter, E-mail: bovy@ias.edu [Max-Planck-Institut für Astronomie, Königstuhl 17, D-69117 Heidelberg (Germany)
2013-12-20
We present and apply rigorous dynamical modeling with which we infer unprecedented constraints on the stellar and dark matter mass distribution within our Milky Way (MW), based on large sets of phase-space data on individual stars. Specifically, we model the dynamics of 16,269 G-type dwarfs from SEGUE, which sample 5 kpc < R{sub GC} < 12 kpc and 0.3 kpc ≲ |Z| ≲ 3 kpc. We independently fit a parameterized MW potential and a three-integral, action-based distribution function (DF) to the phase-space data of 43 separate abundance-selected sub-populations (MAPs), accounting for the complex selection effects affecting the data. We robustly measure the total surface density within 1.1 kpc of the mid-plane to 5% over 4.5 kpc < R{sub GC} < 9 kpc. Using metal-poor MAPs with small radial scale lengths as dynamical tracers probes 4.5 kpc ≲ R{sub GC} ≲ 7 kpc, while MAPs with longer radial scale lengths sample 7 kpc ≲ R{sub GC} ≲ 9 kpc. We measure the mass-weighted Galactic disk scale length to be R{sub d} = 2.15 ± 0.14 kpc, in agreement with the photometrically inferred spatial distribution of stellar mass. We thereby measure dynamically the mass of the Galactic stellar disk to unprecedented accuracy: M {sub *} = 4.6 ± 0.3 + 3.0 (R {sub 0}/ kpc – 8) × 10{sup 10} M {sub ☉} and a total local surface density of Σ{sub R{sub 0}}(Z=1.1 kpc)=68 ± 4 M{sub ⊙} pc{sup −2} of which 38 ± 4 M {sub ☉} pc{sup –2} is contributed by stars and stellar remnants. By combining our surface density measurements with the terminal velocity curve, we find that the MW's disk is maximal in the sense that V {sub c,} {sub disk}/V {sub c,} {sub total} = 0.83 ± 0.04 at R = 2.2 R{sub d} . We also constrain for the first time the radial profile of the dark halo at such small Galactocentric radii, finding that ρ{sub DM}(r; ≈R {sub 0})∝1/r {sup α} with α < 1.53 at 95% confidence. Our results show that action-based DF modeling of complex stellar data sets is now a feasible
Lunkenbein, Thomas; Girgsdies, Frank; Kandemir, Timur; Thomas, Nygil; Behrens, Malte; Schlögl, Robert; Frei, Elias
2016-10-01
Long-term stability of catalysts is an important factor in the chemical industry. This factor is often underestimated in academic testing methods, which may lead to a time gap in the field of catalytic research. The deactivation behavior of an industrially relevant Cu/ZnO/Al2 O3 catalyst for the synthesis of methanol is reported over a period of 148 days time-on-stream (TOS). The process was investigated by a combination of quasi in situ and ex situ analysis techniques. The results show that ZnO is the most dynamic species in the catalyst, whereas only slight changes can be observed in the Cu nanoparticles. Thus, the deactivation of this catalyst is driven by the changes in the ZnO moieties. Our findings indicate that methanol synthesis is an interfacially mediated process between Cu and ZnO.
Bailey, Joseph; Field, Richard; Boyd, Doreen
2016-04-01
We assess the scale-dependency of the relationship between biodiversity and novel geodiversity information by studying spatial patterns of native and alien (archaeophytes and neophytes) vascular plant species richness at varying spatial scales across Great Britain. Instead of using a compound geodiversity metric, we study individual geodiversity components (GDCs) to advance our understanding of which aspects of 'geodiversity' are most important and at what scale. Terrestrial native (n = 1,490) and alien (n = 1,331) vascular plant species richness was modelled across the island of Great Britain at two grain sizes and several extent radii. Various GDCs (landforms, hydrology, geology) were compiled from existing national datasets and automatically extracted landform coverage information (e.g. hollows, valleys, peaks), the latter using a digital elevation model (DEM) and geomorphometric techniques. More traditional predictors of species richness (climate, widely-used topography metrics, land cover diversity, and human population) were also incorporated. Boosted Regression Tree (BRT) models were produced at all grain sizes and extents for each species group and the dominant predictors were assessed. Models with and without geodiversity data were compared. Overarching patterns indicated a clear dominance of geodiversity information at the smallest study extent (12.5km radius) and finest grain size (1x1km), which substantially decreased for each increase in extent as the contribution of climatic variables increased. The contribution of GDCs to biodiversity models was chiefly driven by landform information from geomorphometry, but hydrology (rivers and lakes), and to a lesser extent materials (soil, superficial deposits, and geology), were important, also. GDCs added significantly to vascular plant biodiversity models in Great Britain, independently of widely-used topographic metrics, particularly for native species. The wider consideration of geodiversity alongside
Federighi, Pamela; Wong, Aaron L.; Shelhamer, Mark
2017-01-01
Saccades exhibit variation in performance from one trial to the next, even when paced at a constant rate by targets at two fixed locations. We previously showed that amplitude fluctuations in consecutive predictive saccades have fractal structure: the spectrum of the sequence of consecutive amplitudes has a power-law (f −α) form, indicative of inter-trial correlations that reflect the storage of prior performance information to guide the planning of subsequent movements. More gradual decay of these inter-trial correlations coincides with a larger magnitude of spectral slope α, and indicates stronger information storage over longer times. We have previously demonstrated that larger decay exponents (α) are associated with faster adaptation in a saccadic double-step task. Here, we extend this line of investigation to predictive saccade endpoints (i.e., movement errors). Subjects made predictive, paced saccades between two fixed targets along a horizontal or vertical axis. Endpoint fluctuations both along (on-axis) and orthogonal to (off-axis) the direction of target motion were examined for correlations and fractal structure. Endpoints in the direction of target motion had little or no correlation or power-law scaling, suggesting that successive movements were uncorrelated (white noise). In the orthogonal direction, however, the sequence of endpoints did exhibit inter-trial correlations and scaling. In contrast, in our previous work the scaling of saccade amplitudes is strong along the target direction. This may reflect the fact that while saccade amplitudes are neurally programmed, endpoints are not directly controlled but instead serve as a source of error feedback. Hence, the lack of correlations in on-axis endpoint errors suggests that maximum information has been extracted from previous movement errors to plan subsequent movement amplitudes. In contrast, correlations in the off-axis component indicate that useful information still remains in this error
Iwase, H.; Koizumi, S.; Iikura, H.; Matsubayashi, M.; Yamaguchi, D.; Maekawa, Y.; Hashimoto, T.
2009-06-01
In order to visualize water generated in an operating polymer electrolyte fuel cell (PEFC), a neutron radiography (NR) apparatus, composed of a scintillator, optical mirrors and a CCD camera, was installed at a sample position of the focusing and polarized neutron small-angle scattering (SANS) spectrometer (SANS-J-II) at research reactor JRR-3 at Japan Atomic Energy Agency, Tokai, Japan. By combining SANS and NR, we aim to cover a wide length scale from nanometer to millimeter. The new method succeeded in detecting a spatial distribution of the water generated in individual cell elements; NR detected the water in a gas diffusion layer and a flow field, whereas SANS quantitatively determines the water content in a membrane electrode assembly (MEA).
Minimal Length Scale Scenarios for Quantum Gravity
Hossenfelder, Sabine
2013-01-01
.... First, we examine what insights can be gained from thought experiments for probes of shortest distances, and summarize what can be learned from different approaches to a theory of quantum gravity...
Chromosome length scaling in haploid, asexual reproduction
de Oliveira, P. M. C.
2007-02-01
We study the genetic behaviour of a population formed by haploid individuals which reproduce asexually. The genetic information for each individual is stored along a bit-string (or chromosome) with L bits, where 0-bits represent the wild allele and 1-bits correspond to harmful mutations. Each newborn inherits this chromosome from its parent with a few random mutations: on average a fixed number m of bits are flipped. Selection is implemented according to the number N of 1-bits counted along the individual's chromosome: the smaller N the higher the probability an individual has to survive a new time step. Such a population evolves, with births and deaths, and its genetic distribution becomes stabilized after sufficiently many generations have passed. The question we pose concerns the procedure of increasing L. The aim is to get the same distribution of genetic loads N/L among the equilibrated population, in spite of a larger L. Should we keep the same mutation rate m/L for different values of L? The answer is yes, which intuitively seems to be plausible. However, this conclusion is not trivial, according to our simulation results: the question also involves the population size.
Chromosome length scaling in haploid, asexual reproduction
Oliveira, P M C de [Instituto de Fisica, Universidade Federal Fluminense, avenida Litoranea s/n, Boa Viagem, Niteroi 24210-340 (Brazil)
2007-02-14
We study the genetic behaviour of a population formed by haploid individuals which reproduce asexually. The genetic information for each individual is stored along a bit-string (or chromosome) with L bits, where 0-bits represent the wild allele and 1-bits correspond to harmful mutations. Each newborn inherits this chromosome from its parent with a few random mutations: on average a fixed number m of bits are flipped. Selection is implemented according to the number N of 1-bits counted along the individual's chromosome: the smaller N the higher the probability an individual has to survive a new time step. Such a population evolves, with births and deaths, and its genetic distribution becomes stabilized after sufficiently many generations have passed. The question we pose concerns the procedure of increasing L. The aim is to get the same distribution of genetic loads N/L among the equilibrated population, in spite of a larger L. Should we keep the same mutation rate m/L for different values of L? The answer is yes, which intuitively seems to be plausible. However, this conclusion is not trivial, according to our simulation results: the question also involves the population size.
Nakada, Koji; Ikeda, Masami; Takahashi, Masazumi; Kinami, Shinichi; Yoshida, Masashi; Uenosono, Yoshikazu; Kawashima, Yoshiyuki; Oshio, Atsushi; Suzukamo, Yoshimi; Terashima, Masanori; Kodera, Yasuhiro
2015-01-01
Lack of a suitable instrument to comprehensively assess symptoms, living status, and quality of life in postgastrectomy patients prompted the authors to develop postgastrectomy syndrome assessment scale (PGSAS)-45. PGSAS-45 consists of 45 items in total: 8 items from SF-8, 15 items from GSRS, and an additional 22 items selected by 47 gastric surgeons. Using the PGSAS-45, a multi-institutional survey was conducted to determine the prevalence of postgastrectomy syndrome and its impact on everyday life among patients who underwent various types of gastrectomy. Eligible data were obtained from 2,368 patients operated and followed at 52 institutions in Japan. Of these, data from 1,777 patients were used in the current study in which symptom subscales of the PGSAS-45 were determined. We also considered the characteristics of the postgastrectomy syndrome and to what extent these symptoms influence patients' living status and quality of life (QOL). By factor analysis, 23 symptom-related items of PGSAS-45 were successfully clustered into seven symptom subscales that represent esophageal reflux, abdominal pain, meal-related distress, indigestion, diarrhea, constipation, and dumping. These seven symptom subscales and two other subscales measuring quality of ingestion and dissatisfaction for daily life, respectively, had good internal consistency in terms of Cronbach's α (0.65-0.88). PGSAS-45 provides a valid and reliable integrated index for evaluation of symptoms, living status, and QOL in gastrectomized patients.
Measuring Thermodynamic Length
Crooks, Gavin E
2007-09-07
Thermodynamic length is a metric distance between equilibrium thermodynamic states. Among other interesting properties, this metric asymptotically bounds the dissipation induced by a finite time transformation of a thermodynamic system. It is also connected to the Jensen-Shannon divergence, Fisher information, and Rao's entropy differential metric. Therefore, thermodynamic length is of central interestin understanding matter out of equilibrium. In this Letter, we will consider how to denethermodynamic length for a small system described by equilibrium statistical mechanics and how to measure thermodynamic length within a computer simulation. Surprisingly, Bennett's classic acceptance ratio method for measuring free energy differences also measures thermodynamic length.
Gallen, Sean; Clark, Marin; Godt, Jonathan; Lowe, Katherine
2016-04-01
The material strength of rock is known to be a fundamental property in setting landscape form and geomorphic process rates as it acts to modulate feedbacks between earth surface processes, tectonics, and climate. Despite the long recognition of its importance in landscape evolution, a quantitative understanding of the role of rock strength in affecting geomorphic processes lags our knowledge of the influence of tectonics and climate. This gap stems largely from the fact that it remains challenging to quantify rock strength at the hillslope scale. Rock strength is strongly scale dependent because the number, size, spacing, and aperture of fractures sets the upper limit on rock strength, making it difficult to extrapolate laboratory measurements to landscape-scale interpretations. Here we present a method to determine near-surface rock strength at the hillslope-scale, relying on earthquake-triggered landslides as a regional-scale "shear strength" test. We define near-surface strength as the average strength of rock sample by the landslides, which is typically present results from two well-documented case-studies of earthquakes that caused widespread mass-wasting; the 2008 Mw 7.9 Wenchuan Earthquake, Sichuan Province, China and the 1994 Mw. 6.8 Northridge Earthquake, CA, USA. We show how this model can be used to determine near-surface rock strength and reproduce mapped landslide patterns provided the spatial distribution of local hillslope gradient, earthquake peak ground acceleration (PGA), and coseismic landsliding are well constrained. Results suggest that near-surface rock strength in these tectonically active settings is much lower than that obtained using typical laboratory shear strength measurements on intact rock samples. Furthermore, the near-surface material strength is similar between the study areas despite differences in tectonic, climatic, and lithologic conditions. Variations in near-surface strength within each setting appear to be more strongly
Perceptually Relevant and Piecewise Linear Matching of Silhouettes
Zabulis, Xenophon; Sporring, Jon; Orphanoudakis, Xenophon
2005-01-01
correct correspondences than conventional methods that scale the arc-length descriptions of silhouettes to align them. The selection of landmarks is investigated as to the robustness of their localization and their perceptual relevance. Matching of silhouettes is then achieved by quantifying...... the dissimilarity of a pair of silhouette boundaries, based on a novel dissimilarity metric. The matching procedure is evaluated, based on retrieval experiments, and it is concluded that the precision of the results is higher than that obtained by conventional pointwise comparison methods....
The Harmonic Oscillator in the Classical Limit of a Minimal-Length Scenario
Quintela, T. S.; Fabris, J. C.; Nogueira, J. A.
2016-09-01
In this work, we explicitly solve the problem of the harmonic oscillator in the classical limit of a minimal-length scenario. We show that (i) the motion equation of the oscillator is not linear anymore because the presence of a minimal length introduces an anarmonic term and (ii) its motion is described by a Jacobi sine elliptic function. Therefore, the motion is periodic with the same amplitude and with the new period depending on the minimal length. This result (the change in the period of oscillation) is very important since it enables us to find in a quite simple way the most relevant effect of the presence of a minimal length and consequently traces of the Planck-scale physics. We show applications of our results in spectroscopy and gravity.
Scaling properties of universal tetramers.
Hadizadeh, M R; Yamashita, M T; Tomio, Lauro; Delfino, A; Frederico, T
2011-09-23
We evidence the existence of a universal correlation between the binding energies of successive four-boson bound states (tetramers), for large two-body scattering lengths (a), related to an additional scale not constrained by three-body Efimov physics. Relevant to ultracold atom experiments, the atom-trimer relaxation peaks for |a|→∞ when the ratio between the tetramer and trimer energies is ≃4.6 and a new tetramer is formed. The new scale is also revealed for a < 0 by the prediction of a correlation between the positions of two successive peaks in the four-atom recombination process.
Why relevance theory is relevant for lexicography
Bothma, Theo; Tarp, Sven
2014-01-01
, socio-cognitive and affective relevance. It then shows, at the hand of examples, why relevance is important from a user perspective in the extra-lexicographical pre- and post-consultation phases and in the intra-lexicographical consultation phase. It defines an additional type of subjective relevance...... that is very important for lexicography as well as for information science, viz. functional relevance. Since all lexicographic work is ultimately aimed at satisfying users’ information needs, the article then discusses why the lexicographer should take note of all these types of relevance when planning a new...... dictionary project, identifying new tasks and responsibilities of the modern lexicographer. The article furthermore discusses how relevance theory impacts on teaching dictionary culture and reference skills. By integrating insights from lexicography and information science, the article contributes to new...
Gupta, Ankur [Department of Materials Science and Engineering, Indian Institute of Technology, Kanpur 208016 (India); Advanced Materials Processing and Analysis Center, Department of Materials Science and Engineering, University of Central Florida, Orlando, FL 32826 (United States); Kumar, Vinod [Department of Materials Science and Engineering, Indian Institute of Technology, Kanpur 208016 (India); Department of Metallurgical and Materials Engineering, Malaviya National Institute of Technology, Jaipur 302017 (India); Nair, Jitin [Department of Materials and Metallurgical Engineering, National Institute of Foundry and Forge Technology, Ranchi 834003 (India); Bansal, Ankit [Department of Materials Science and Engineering, Indian Institute of Technology, Kanpur 208016 (India); Tata Steel Ltd., Jamshedpur, Jharkhand 831001 (India); Balani, Kantesh, E-mail: kbalani@iitk.ac.in [Department of Materials Science and Engineering, Indian Institute of Technology, Kanpur 208016 (India)
2015-06-15
Highlights: • Dual phase (α + β) Mg–9Li–7Al–1Sn (LAT971) and Mg–9Li–5Al–3Sn–1Zn (LATZ9531) alloys. • Effective elastic modulus estimated from finite element method (FEM). • Correlation of nanoscale mechanical data with microstress distribution. • Precipitates of Mg–Al–Li act as stress relaxer and Mg–Li–Sn as stress concentrator. • Higher local heterogeneous stress distribution (∼0.6–5.7 GPa) in LATZ9531 alloys. - Abstract: In the recent years, magnesium–lithium (Mg–Li) alloys have attracted considerable attention/interest due to their high strength-to-density ratio and damping characteristic; and have found potential use in structural and biomedical applications. Here the mechanical behavior of novel Mg–9 wt.% Li–7 wt.% Al–1 wt.% Sn (LAT971) and Mg–9 wt.% Li–5 wt.% Al–3 wt.% Sn–1 wt.% Zn (LATZ9531) alloys is reported. Both, as cast and thermomechanically processed alloys have been studied which possess dual phase microstructure. Nanoindentation data have been utilized to envisage the elastic modulus of alloy via various micromechanics models (such as rule of mixtures, Voigt–Reuss, Cox model, Halpin–Tsai and Guth model) in order to estimate the elastic modulus. Object oriented finite element modeling (FEM) has been performed to predict stress distribution under tensile and compressive strain state. Close match between Halpin–Tsai model and FEM results show the abridgment of nano length scale property to evolution of microscopic stress distribution in novel LAT971 and LATZ9531 Mg–Li–Al based alloys.
Minimum Length - Maximum Velocity
Panes, Boris
2011-01-01
We study a framework where the hypothesis of a minimum length in space-time is complemented with the notion of reference frame invariance. It turns out natural to interpret the action of the obtained reference frame transformations in the context of doubly special relativity. As a consequence of this formalism we find interesting connections between the minimum length properties and the modified velocity-energy relation for ultra-relativistic particles. For example we can predict the ratio between the minimum lengths in space and time using the results from OPERA about superluminal neutrinos.
Telomere length and depression
Wium-Andersen, Marie Kim; Ørsted, David Dynnes; Rode, Line
2016-01-01
BACKGROUND: Depression has been cross-sectionally associated with short telomeres as a measure of biological age. However, the direction and nature of the association is currently unclear. AIMS: We examined whether short telomere length is associated with depression cross-sectionally as well...... as prospectively and genetically. METHOD: Telomere length and three polymorphisms, TERT, TERC and OBFC1, were measured in 67 306 individuals aged 20-100 years from the Danish general population and associated with register-based attendance at hospital for depression and purchase of antidepressant medication....... RESULTS: Attendance at hospital for depression was associated with short telomere length cross-sectionally, but not prospectively. Further, purchase of antidepressant medication was not associated with short telomere length cross-sectionally or prospectively. Mean follow-up was 7.6 years (range 0...
Myofilament length dependent activation
de Tombe, Pieter P.; Mateja, Ryan D.; Tachampa, Kittipong; Mou, Younss Ait; Farman, Gerrie P.; Irving, Thomas C. (IIT); (Loyola)
2010-05-25
The Frank-Starling law of the heart describes the interrelationship between end-diastolic volume and cardiac ejection volume, a regulatory system that operates on a beat-to-beat basis. The main cellular mechanism that underlies this phenomenon is an increase in the responsiveness of cardiac myofilaments to activating Ca{sup 2+} ions at a longer sarcomere length, commonly referred to as myofilament length-dependent activation. This review focuses on what molecular mechanisms may underlie myofilament length dependency. Specifically, the roles of inter-filament spacing, thick and thin filament based regulation, as well as sarcomeric regulatory proteins are discussed. Although the 'Frank-Starling law of the heart' constitutes a fundamental cardiac property that has been appreciated for well over a century, it is still not known in muscle how the contractile apparatus transduces the information concerning sarcomere length to modulate ventricular pressure development.
A Characteristic Particle Length
Roberts, Mark D
2015-01-01
It is argued that there are characteristic intervals associated with any particle that can be derived without reference to the speed of light $c$. Such intervals are inferred from zeros of wavefunctions which are solutions to the Schr\\"odinger equation. The characteristic length is $\\ell=\\beta^2\\hbar^2/(8Gm^3)$, where $\\beta=3.8\\dots$; this length might lead to observational effects on objects the size of a virus.
Demaison, Jean; Császár, Attila G.
2012-09-01
Based on a sample of 38 molecules, 47 accurate equilibrium CO bond lengths have been collected and analyzed. These ultimate experimental (reEX), semiexperimental (reSE), and Born-Oppenheimer (reBO) equilibrium structures are compared to reBO estimates from two lower-level techniques of electronic structure theory, MP2(FC)/cc-pVQZ and B3LYP/6-311+G(3df,2pd). A linear relationship is found between the best equilibrium bond lengths and their MP2 or B3LYP estimates. These (and similar) linear relationships permit to estimate the CO bond length with an accuracy of 0.002 Å within the full range of 1.10-1.43 Å, corresponding to single, double, and triple CO bonds, for a large number of molecules. The variation of the CO bond length is qualitatively explained using the Atoms in Molecules method. In particular, a nice correlation is found between the CO bond length and the bond critical point density and it appears that the CO bond is at the same time covalent and ionic. Conditions which permit the computation of an accurate ab initio Born-Oppenheimer equilibrium structure are discussed. In particular, the core-core and core-valence correlation is investigated and it is shown to roughly increase with the bond length.
Observations on oesophageal length.
Kalloor, G J; Deshpande, A H; Collis, J L
1976-01-01
The subject of oesophageal length is discussed. The great variations in the length of the oesophagus in individual patients is noted, and the practical use of its recognition in oesophageal surgery is stressed. An apprasial of the various methods available for this measurement is made; this includes the use of external chest measurement, endoscopic measurement, and the measurement of the level of the electrical mucosal potential change. Correlative studies of these various methods are made, and these show a very high degree of significance. These studies involved simultaneous measurement of external and internal oesophageal length in 26 patients without a hiatal hernia or gastro-oesophageal length in 26 patients without a hiatal hernia or gastro-oesophageal reflux symptoms, 42 patients with sliding type hiatal hernia, and 17 patients with a peptic stricture in association with hiatal hernia. The method of measuring oesophageal length by the use of the external chest measurement, that is, the distance between the lower incisor teeth and the xiphisternum, measured with the neck fully extended and the patient lying supine, is described in detail, its practical application in oesophageal surgery is illustrated, and its validity tested by internal measurements. The findings of this study demonstrate that the external chest measurement provides a mean of assessing the true static length of the oesophagus, corrected for the size of the individual. Images PMID:941114
Wentian eLi
2014-11-01
Full Text Available Power-law distributions are the main functional form forthe distribution of repeat size and repeat copy number in the human genome. When the genome is broken into fragments for sequencing, the limited size offragments and reads may prevent an unique alignment of repeatsequences to the reference sequence. Repeats in the human genome canbe as long as $10^4$ bases, or $10^5-10^6$ bases when allowing for mismatches between repeat units. Sequence reads from these regions are therefore unmappable when the read length is in the range of $10^3$ bases.With the read length of exactly 1000 bases, slightly more than 1% of theassembled genome, and slightly less than 1% of the 1kbreads, are unmappable, excluding the unassembled portion of the humangenome (8% in GRCh37. The slow decay (long tail ofthe power-law function implies a diminishing return in convertingunmappable regions/reads to become mappable with the increase of theread length, with the understanding that increasing read length willalways move towards the direction of 100% mappability.
Kimura, Masayuki; Hjelmborg, Jacob V B; Gardner, Jeffrey P
2008-01-01
telomeres predicted the death of the first co-twin better than the mTRFL did (mTRFL: 0.56, 95% confidence interval (CI): 0.49, 0.63; mTRFL(50): 0.59, 95% CI: 0.52, 0.66; mTRFL(25): 0.59, 95% CI: 0.52, 0.66; MTRFL: 0.60, 95% CI: 0.53, 0.67). The telomere-mortality association was stronger in years 3-4 than......Leukocyte telomere length, representing the mean length of all telomeres in leukocytes, is ostensibly a bioindicator of human aging. The authors hypothesized that shorter telomeres might forecast imminent mortality in elderly people better than leukocyte telomere length. They performed mortality...... analysis in 548 same-sex Danish twins (274 pairs) aged 73-94 years, of whom 204 pairs experienced the death of one or both co-twins during 9-10 years of follow-up (1997-2007). From the terminal restriction fragment length (TRFL) distribution, the authors obtained the mean TRFL (mTRFL) and the mean values...
PENDULUM WITH LINEAR DAMPING AND VARIABLE LENGTH
蔡建平; 杨翠红; 李怡平
2004-01-01
The methods of multiple scales and approximate potential are used to study pendulums with linear damping and variable length. According to the order of the coefficient of friction compared with that of the slowly varying parameter of length, three different cases are discussed in details. Asymptotic analytical expressions of amplitude, frequency and solution are obtained. The method of approximate potential makes the results effective for large oscillations. A modified multiple scales method is used to get more accurate leading order approximations when the coefficient friction is not small. Comparisons are also made with numerical results to show the efficiency of the present method.
Lioma, Christina; Larsen, Birger; Petersen, Casper
2016-01-01
train a Recurrent Neural Network (RNN) on existing relevant information to that query. We then use the RNN to "deep learn" a single, synthetic, and we assume, relevant document for that query. We design a crowdsourcing experiment to assess how relevant the "deep learned" document is, compared......What if Information Retrieval (IR) systems did not just retrieve relevant information that is stored in their indices, but could also "understand" it and synthesise it into a single document? We present a preliminary study that makes a first step towards answering this question. Given a query, we...... to existing relevant documents. Users are shown a query and four wordclouds (of three existing relevant documents and our deep learned synthetic document). The synthetic document is ranked on average most relevant of all....
Relativistic length agony continued
Redžić D.V.
2014-01-01
Full Text Available We made an attempt to remedy recent confusing treatments of some basic relativistic concepts and results. Following the argument presented in an earlier paper (Redžić 2008b, we discussed the misconceptions that are recurrent points in the literature devoted to teaching relativity such as: there is no change in the object in Special Relativity, illusory character of relativistic length contraction, stresses and strains induced by Lorentz contraction, and related issues. We gave several examples of the traps of everyday language that lurk in Special Relativity. To remove a possible conceptual and terminological muddle, we made a distinction between the relativistic length reduction and relativistic FitzGerald-Lorentz contraction, corresponding to a passive and an active aspect of length contraction, respectively; we pointed out that both aspects have fundamental dynamical contents. As an illustration of our considerations, we discussed briefly the Dewan-Beran-Bell spaceship paradox and the ‘pole in a barn’ paradox. [Projekat Ministarstva nauke Republike Srbije, br. 171028
Ground Wood Fiber Length Distributions
Lauri Ilmari Salminen; Sari Liukkonen; Alava, Mikko J.
2014-01-01
This study considers ground wood fiber length distributions arising from pilot grindings. The empirical fiber length distributions appear to be independent of wood fiber length as well as feeding velocity. In terms of mathematics the fiber fragment distributions of ground wood pulp combine an exponential distribution for high-length fragments and a power-law distribution for smaller lengths. This implies that the fiber length distribution is influenced by the stone surface. A fragmentation-ba...
Fuzziness and Relevance Theory
Grace Qiao Zhang
2005-01-01
This paper investigates how the phenomenon of fuzzy language, such as `many' in `Mary has many friends', can be explained by Relevance Theory. It is concluded that fuzzy language use conforms with optimal relevance in that it can achieve the greatest positive effect with the least processing effort. It is the communicators themselves who decide whether or not optimal relevance is achieved, rather than the language form (fuzzy or non-fuzzy) used. People can skillfully adjust the deployment of different language forms or choose appropriate interpretations to suit different situations and communication needs. However, there are two challenges to RT: a. to extend its theory from individual relevance to group relevance; b. to embrace cultural considerations (because when relevance principles and cultural protocols are in conflict, the latter tends to prevail).
Perceptions of document relevance
Peter eBruza
2014-07-01
Full Text Available This article presents a study of how humans perceive the relevance of documents.Humans are adept at making reasonably robust and quick decisions about what information is relevant to them, despite the ever increasing complexity and volume of their surrounding information environment. The literature on document relevance has identified various dimensions of relevance (e.g., topicality, novelty, etc., however little is understood about how these dimensions may interact.We performed a crowdsourced study of how human subjects judge two relevance dimensions in relation to document snippets retrieved from an internet search engine.The order of the judgement was controlled.For those judgements exhibiting an order effect, a q-test was performed to determine whether the order effects can be explained by a quantum decision model based on incompatible decision perspectives.Some evidence of incompatibility was found which suggests incompatible decision perspectives is appropriate for explaining interacting dimensions of relevance.
Relevance Theory in Translation
Shao Jun; Jiang Min
2008-01-01
In perspective of relevance theory, translation is regarded as communication. According to relevance theory, communication not only requires encoding, transfer and decoding processes, but also involves inference in addition. As communication, translation decision-making is also based on the human beings' inferential mental faculty. Concentrating on relevance theory, this paper tries to analyze and explain some translation phenomena in two English versions of Cai Gen Tan-My Crude Philosophy of Life.
Length, protein–protein interactions, and complexity
Tan, T.; Frenkel, D.; Gupta, V.; Deem, M.W.
2005-01-01
The evolutionary reason for the increase in gene length from archaea to prokaryotes to eukaryotes observed in large-scale genome sequencing efforts has been unclear. We propose here that the increasing complexity of protein–protein interactions has driven the selection of longer proteins, as they ar
P. R. Parthasarathy
2001-01-01
Full Text Available The transient solution is obtained analytically using continued fractions for a state-dependent birth-death queue in which potential customers are discouraged by the queue length. This queueing system is then compared with the well-known infinite server queueing system which has the same steady state solution as the model under consideration, whereas their transient solutions are different. A natural measure of speed of convergence of the mean number in the system to its stationarity is also computed.
姜志宏; 王晖; 李沛; 樊鹏翼
2012-01-01
P2P TV已经成为一种越来越普及的新型电视服务平台.与传统有线电视相比较,基于互联网的P2PTV在影响范围、交互性和开放性等方面都具有巨大的优势.P2P TV用户在感受到不同于传统电视的收看体验的同时,也表现出了不同于传统电视用户的收看行为.在利用自主研发的测量工具-TVCrawler获取实际系统数据的基础上,对P2P TV用户的会话时长进行了深入研究.按照P2P TV用户会话时长的分布特点,将其分为轻度收看者、中度收看者和重度收看者三类,对应的平均会话时长分别为3～5分钟,20～50分钟和120～200分钟,并进一步分析了在各被测频道中,三类用户各自的在线人数和到达率.%P2P TV system is getting more and more popular as a new TV service. In contrast with traditional cable and satellite TV system, the Internet-based P2P TV is more interactive, more open, and has wider sphere of influence. While getting some new experience that is different from traditional TV system, P2P TV users have exhibited some new characters of viewing behavior. In this work, it performs an in-depth study on session length of P2P TV user by analyzing the real data collected from the self-developed measuring tool named TVCrawler. According to the distribution characters of user session length, it puts P2P TV users into three categories: light viewers with 3~5 minutes of mean session length, medium viewers with 20~50 minutes of mean session length, and heavy viewers with 120-200 minutes of mean session length. It analyzes online number and arrival rate for different categories of users.
Pragmatic inferences and self-relevant judgments
Puente-Diaz, Rogelio; Cavazos Arroyo, Judith; Brem, Alexander
2016-01-01
Three studies examined the influence of type of scale on self-relevant judgments and the moderating role of age, prevention, focus, and need for cogni- tion. Participants were randomly assigned to a bipolar or a unipolar scale condition in all three studies. Results from study 1 with a representa...
Eick, Charles; Deutsch, Bill; Fuller, Jennifer; Scott, Fletcher
2008-01-01
Science teachers are always looking for ways to demonstrate the relevance of science to students. By connecting science learning to important societal issues, teachers can motivate students to both enjoy and engage in relevant science (Bennet, Lubben, and Hogarth 2007). To develop that connection, teachers can help students take an active role in…
Functionally relevant microsatellites in sugarcane unigenes
Singh Nagendra K
2010-11-01
Full Text Available Abstract Background Unigene sequences constitute a rich source of functionally relevant microsatellites. The present study was undertaken to mine the microsatellites in the available unigene sequences of sugarcane for understanding their constitution in the expressed genic component of its complex polyploid/aneuploid genome, assessing their functional significance in silico, determining the extent of allelic diversity at the microsatellite loci and for evaluating their utility in large-scale genotyping applications in sugarcane. Results The average frequency of perfect microsatellite was 1/10.9 kb, while it was 1/44.3 kb for the long and hypervariable class I repeats. GC-rich trinucleotides coding for alanine and the GA-rich dinucleotides were the most abundant microsatellite classes. Out of 15,594 unigenes mined in the study, 767 contained microsatellite repeats and for 672 of these putative functions were determined in silico. The microsatellite repeats were found in the functional domains of proteins encoded by 364 unigenes. Its significance was assessed by establishing the structure-function relationship for the beta-amylase and protein kinase encoding unigenes having repeats in the catalytic domains. A total of 726 allelic variants (7.42 alleles per locus with different repeat lengths were captured precisely for a set of 47 fluorescent dye labeled primers in 36 sugarcane genotypes and five cereal species using the automated fragment analysis system, which suggested the utility of designed primers for rapid, large-scale and high-throughput genotyping applications in sugarcane. Pair-wise similarity ranging from 0.33 to 0.84 with an average of 0.40 revealed a broad genetic base of the Indian varieties in respect of functionally relevant regions of the large and complex sugarcane genome. Conclusion Microsatellite repeats were present in 4.92% of sugarcane unigenes, for most (87.6% of which functions were determined in silico. High level of
Ground Wood Fiber Length Distributions
Lauri Ilmari Salminen
2014-01-01
Full Text Available This study considers ground wood fiber length distributions arising from pilot grindings. The empirical fiber length distributions appear to be independent of wood fiber length as well as feeding velocity. In terms of mathematics the fiber fragment distributions of ground wood pulp combine an exponential distribution for high-length fragments and a power-law distribution for smaller lengths. This implies that the fiber length distribution is influenced by the stone surface. A fragmentation-based model is presented that allows reproduction of the empirical results.
Criticisms of Relevance Theory
尚静; 孟晔; 焦丽芳
2006-01-01
This paper briefly introduces first the notion of Sperber and Wilson's Relevance Theory. Then, the motivation of S & W putting forward their RT is also mentioned. Secondly, the paper gives some details about the methodology of RT, in which ostensive-inferential communication, context and optimal relevance are highlighted. Thirdly, the paper focuses on the criticisms of RT from different areas of research on human language and communication. Finally, the paper draws a conclusion on the great importance of RT in pragmatics.
Electrophoresis of semiflexible heteropolymers and the ``hydrodynamic Kuhn length''
Chubynsky, Mykyta V.; Slater, Gary W.
Semiflexible polymers, such as DNA, are rodlike for short lengths and coil-like for long lengths. For purely geometric properties, such as the end-to-end distance, the crossover between these two behaviors occurs when the polymer length is on the order of the Kuhn length. On the other hand, for the hydrodynamic friction coefficient it is easy to see by comparing the expressions for a rod and a coil that the crossover should occur at the polymer length, termed by us the hydrodynamic Kuhn length, which is larger than the ordinary Kuhn length by a logarithmic factor that can be quite significant. We show that for the problem of electrophoresis of a heteropolymer consisting of several blocks of (in general) different stiffnesses, both of these length scales can be important depending on the details of the problem.
Min Lin
Full Text Available BACKGROUND: Cotton (Gossypium hirsutum L. is one of the world's most economically-important crops. However, its entire genome has not been sequenced, and limited resources are available in GenBank for understanding the molecular mechanisms underlying leaf development and senescence. METHODOLOGY/PRINCIPAL FINDINGS: In this study, 9,874 high-quality ESTs were generated from a normalized, full-length cDNA library derived from pooled RNA isolated from throughout leaf development during the plant blooming stage. After clustering and assembly of these ESTs, 5,191 unique sequences, representative 1,652 contigs and 3,539 singletons, were obtained. The average unique sequence length was 682 bp. Annotation of these unique sequences revealed that 84.4% showed significant homology to sequences in the NCBI non-redundant protein database, and 57.3% had significant hits to known proteins in the Swiss-Prot database. Comparative analysis indicated that our library added 2,400 ESTs and 991 unique sequences to those known for cotton. The unigenes were functionally characterized by gene ontology annotation. We identified 1,339 and 200 unigenes as potential leaf senescence-related genes and transcription factors, respectively. Moreover, nine genes related to leaf senescence and eleven MYB transcription factors were randomly selected for quantitative real-time PCR (qRT-PCR, which revealed that these genes were regulated differentially during senescence. The qRT-PCR for three GhYLSs revealed that these genes express express preferentially in senescent leaves. CONCLUSIONS/SIGNIFICANCE: These EST resources will provide valuable sequence information for gene expression profiling analyses and functional genomics studies to elucidate their roles, as well as for studying the mechanisms of leaf development and senescence in cotton and discovering candidate genes related to important agronomic traits of cotton. These data will also facilitate future whole-genome sequence
Grace, Emily; Butcher, Alistair; Monroe, Jocelyn; Nikkel, James A.
2017-09-01
Large liquid argon detectors have become widely used in low rate experiments, including dark matter and neutrino research. However, the optical properties of liquid argon are not well understood at the large scales relevant for current and near-future detectors. The index of refraction of liquid argon at the scintillation wavelength has not been measured, and current Rayleigh scattering length calculations disagree with measurements. Furthermore, the Rayleigh scattering length and index of refraction of solid argon and solid xenon at their scintillation wavelengths have not been previously measured or calculated. We introduce a new calculation using existing data in liquid and solid argon and xenon to extrapolate the optical properties at the scintillation wavelengths using the Sellmeier dispersion relationship.
Averill, M.; Briggle, A.
2006-12-01
Science policy and knowledge production lately have taken a pragmatic turn. Funding agencies increasingly are requiring scientists to explain the relevance of their work to society. This stems in part from mounting critiques of the "linear model" of knowledge production in which scientists operating according to their own interests or disciplinary standards are presumed to automatically produce knowledge that is of relevance outside of their narrow communities. Many contend that funded scientific research should be linked more directly to societal goals, which implies a shift in the kind of research that will be funded. While both authors support the concept of useful science, we question the exact meaning of "relevance" and the wisdom of allowing it to control research agendas. We hope to contribute to the conversation by thinking more critically about the meaning and limits of the term "relevance" and the trade-offs implicit in a narrow utilitarian approach. The paper will consider which interests tend to be privileged by an emphasis on relevance and address issues such as whose goals ought to be pursued and why, and who gets to decide. We will consider how relevance, narrowly construed, may actually limit the ultimate utility of scientific research. The paper also will reflect on the worthiness of research goals themselves and their relationship to a broader view of what it means to be human and to live in society. Just as there is more to being human than the pragmatic demands of daily life, there is more at issue with knowledge production than finding the most efficient ways to satisfy consumer preferences or fix near-term policy problems. We will conclude by calling for a balanced approach to funding research that addresses society's most pressing needs but also supports innovative research with less immediately apparent application.
Relevant Criteria for Testing the Quality of Models for Turbulent Wind Speed Fluctuations
Frandsen, Sten Tronæs; Ejsing Jørgensen, Hans; Sørensen, John Dalsgaard
2008-01-01
-size wind turbines when seeking wind characteristics that correspond to one blade and the entire rotor, respectively. For heights exceeding 50-60 m, the gust factor increases with wind speed. For heights larger than 60-80 m, present assumptions on the value of the gust factor are significantly......Seeking relevant criteria for testing the quality of turbulence models, the scale of turbulence and the gust factor have been estimated from data and compared with predictions from first-order models of these two quantities. It is found that the mean of the measured length scales is approximately...... 10% smaller than the IEC model for wind turbine hub height levels. The mean is only marginally dependent on trends in time series. It is also found that the coefficient of variation of the measured length scales is about 50%. 3 s and 10 s preaveraging of wind speed data are relevant for megawatt...
On some length biased inequalities for reliability measures
Oluyede BroderickO
2000-01-01
Full Text Available In this note, inequalities for length biased and the original residual life function and equilibrium distribution function with monotone hazard rate and mean residual life functions are derived. We also obtain estimates of the length biased probability density function and hazard function under random censoring. Finally, the Bayesian exponential reliability estimate under length biased sampling using a conjugate prior for the scale parameter is given.
Persistence Length of DNA Macromolecule with Kinks
Simonov, Kyrylo
2014-01-01
The study of configurational parameters of deformed DNA is a relevant problem in research of such important biological process as double helix compactization in cell. The deformations accompanied with local disruptions of the regular macromolecule structure cause significant bending of the double helix, or kinks. In this paper an approach for Kratky-Porod model to calculate persistence length of DNA macromolecule with kinks is developed. The presented approach considers kinks of arbitrary configuration, including two basic types of kinks, type 1 - sharp kink caused by unstacking a single base pair step, and type 2 - intrinsic-induced kink that involves several base pairs. Within developed approach analytical expressions for persistence length, coil size and gyration radius of kinky double helix were obtained.
Dunham, L. L.
1971-01-01
The "legacy" of the humanities is discussed in terms of relevance, involvement, and other philosophical considerations. Reasons for studying foreign literature in language classes are developed in the article. Comment is also made on attitudes and ideas culled from the writings of Clifton Fadiman, Jean Paul Sartre, and James Baldwin. (RL)
Müller, Emmanuel; Assent, Ira; Günnemann, Stephan
2009-01-01
. We prove that computation of this model is NP-hard. For RESCU, we propose an approximative solution that shows high accuracy with respect to our relevance model. Thorough experiments on synthetic and real world data show that RESCU successfully reduces the result to manageable sizes. It reliably...... achieves top clustering quality while competing approaches show greatly varying performance....
Is Information Still Relevant?
Ma, Lia
2013-01-01
Introduction: The term "information" in information science does not share the characteristics of those of a nomenclature: it does not bear a generally accepted definition and it does not serve as the bases and assumptions for research studies. As the data deluge has arrived, is the concept of information still relevant for information…
Müller, Emmanuel; Assent, Ira; Günnemann, Stephan;
2009-01-01
Subspace clustering aims at detecting clusters in any subspace projection of a high dimensional space. As the number of possible subspace projections is exponential in the number of dimensions, the result is often tremendously large. Recent approaches fail to reduce results to relevant subspace c...
Does an inter-flaw length control the accuracy of rupture forecasting in geological materials?
Vasseur, Jérémie; Wadsworth, Fabian B.; Heap, Michael J.; Main, Ian G.; Lavallée, Yan; Dingwell, Donald B.
2017-10-01
Multi-scale failure of porous materials is an important phenomenon in nature and in material physics - from controlled laboratory tests to rockbursts, landslides, volcanic eruptions and earthquakes. A key unsolved research question is how to accurately forecast the time of system-sized catastrophic failure, based on observations of precursory events such as acoustic emissions (AE) in laboratory samples, or, on a larger scale, small earthquakes. Until now, the length scale associated with precursory events has not been well quantified, resulting in forecasting tools that are often unreliable. Here we test the hypothesis that the accuracy of the forecast failure time depends on the inter-flaw distance in the starting material. We use new experimental datasets for the deformation of porous materials to infer the critical crack length at failure from a static damage mechanics model. The style of acceleration of AE rate prior to failure, and the accuracy of forecast failure time, both depend on whether the cracks can span the inter-flaw length or not. A smooth inverse power-law acceleration of AE rate to failure, and an accurate forecast, occurs when the cracks are sufficiently long to bridge pore spaces. When this is not the case, the predicted failure time is much less accurate and failure is preceded by an exponential AE rate trend. Finally, we provide a quantitative and pragmatic correction for the systematic error in the forecast failure time, valid for structurally isotropic porous materials, which could be tested against larger-scale natural failure events, with suitable scaling for the relevant inter-flaw distances.
FETAL FOOT LENGTH AND HAND LENGTH: RELATIONSHIP WITH CROWN RUMP LENGTH AND GESTATIONAL AGE
Garima
2015-12-01
Full Text Available BACKGROUND Estimation of gestational age of fetus is of great medicolegal importance. Multiple parameters of the fetal anatomical measurements are in use. However, gestational age assessment may be difficult in fetus with anencephaly, hydrocephalus, short limb dysplasia, post mortem destruction or in mutilated case. Study of literature suggests that fetal foot has a characteristic pattern of normal growth and the fetal foot shows gradual increase in length relative to the length of the embryo and could be used to estimate gestational age. The purpose of the present study is to determine the accuracy in estimating gestational age using fetal foot and hand length by studying its relation with crown rump length in the foetuses of Manipuri origin. AIMS AND OBJECTIVES 1 To study the relationship between fetal crown rump length and fetal hand and foot length, thereby determining the accuracy in estimating gestational age by a cross-sectional study. MATERIALS AND METHODS A total of 100 formalin fixed fetuses of Manipuri origin, obtained from the Department of Obstetrics and Gynaecology, Regional Institute of Medical Sciences, Imphal, were included in the study, carried out in the Department of Anatomy, from February 2015 to July 2015. The parameters studied were crown rump length, foot length and hand length of fetuses. The data was analysed using SPSS software by regression analysis. Graphs were also plotted to determine pattern of growth and their correlation with crown rump length if any. RESULTS A total of 100 fetuses were studied, of which 43 were females and 57 were males. The mean foot length and hand length progressively increased with increase in crown rump length. Measurements were not significantly different in right or left side or among male and female fetuses. A statistically significant linear relationship was seen between foot length and crown rump length of the fetus (r=0.980, p<0.0001 and hand length and crown rump length of the fetus
Determination of Arabidopsis thaliana telomere length by PCR.
Vaquero-Sedas, María I; Vega-Palas, Miguel A
2014-07-02
In humans, telomere length studies have acquired great relevance because the length of telomeres has been related to natural processes like disease, aging and cancer. However, very little is known about the influence of telomere length on the biology of wild type plants. The length of plant telomeres has been usually studied by Terminal Restriction Fragment (TRF) analyses. This technique requires high amounts of tissue, including multiple cell types, which might be the reason why very little is known about the influence of telomere length on plant natural processes. In contrast, many of the human telomere length studies have focused on homogenous cell populations. Most of these studies have been performed by PCR, using telomeric degenerated primers, which allow the determination of telomere length from small amounts of human cells. Here, we have adapted the human PCR procedure to analyze the length of Arabidopsis thaliana telomeres. This PCR approach will facilitate the analysis of telomere length from low amounts of tissue. We have used it to determine that CG and non CG DNA methylation positively regulates Arabidopsis telomere length.
Clinical Relevance of Adipokines
Matthias Blüher
2012-10-01
Full Text Available The incidence of obesity has increased dramatically during recent decades. Obesity increases the risk for metabolic and cardiovascular diseases and may therefore contribute to premature death. With increasing fat mass, secretion of adipose tissue derived bioactive molecules (adipokines changes towards a pro-inflammatory, diabetogenic and atherogenic pattern. Adipokines are involved in the regulation of appetite and satiety, energy expenditure, activity, endothelial function, hemostasis, blood pressure, insulin sensitivity, energy metabolism in insulin sensitive tissues, adipogenesis, fat distribution and insulin secretion in pancreatic β-cells. Therefore, adipokines are clinically relevant as biomarkers for fat distribution, adipose tissue function, liver fat content, insulin sensitivity, chronic inflammation and have the potential for future pharmacological treatment strategies for obesity and its related diseases. This review focuses on the clinical relevance of selected adipokines as markers or predictors of obesity related diseases and as potential therapeutic tools or targets in metabolic and cardiovascular diseases.
Bergenholtz, Henning; Gouws, Rufus
2007-01-01
as detrimental to the status of a dictionary as a container of linguistic knowledge. This paper shows that, from a lexicographic perspective, such a distinction is not relevant. What is important is that definitions should contain information that is relevant to and needed by the target users of that specific......In explanatory dictionaries, both general language dictionaries and dictionaries dealing with languages for special purposes, the lexicographic definition is an important item to present the meaning of a given lemma. Due to a strong linguistic bias, resulting from an approach prevalent in the early...... phases of the development of theoretical lexicography, a distinction is often made between encyclopaedic information and semantic information in dictionary definitions, and dictionaries had often been criticized when their definitions were dominated by an encyclopaedic approach. This used to be seen...
IMPEDANCE OF FINITE LENGTH RESISTOR
KRINSKY, S.; PODOBEDOV, B.; GLUCKSTERN, R.L.
2005-05-15
We determine the impedance of a cylindrical metal tube (resistor) of radius a, length g, and conductivity {sigma}, attached at each end to perfect conductors of semi-infinite length. Our main interest is in the asymptotic behavior of the impedance at high frequency, k >> 1/a. In the equilibrium regime, , the impedance per unit length is accurately described by the well-known result for an infinite length tube with conductivity {sigma}. In the transient regime, ka{sup 2} >> g, we derive analytic expressions for the impedance and wakefield.
Wildemuth, Barbara M.
2009-01-01
A user's interaction with a DL is often initiated as the result of the user experiencing an information need of some kind. Aspects of that experience and how it might affect the user's interactions with the DL are discussed in this module. In addition, users continuously make decisions about and evaluations of the materials retrieved from a DL, relative to their information needs. Relevance judgments, and their relationship to the user's information needs, are discussed in this module. Draft
Fractional Moment Bounds and Disorder Relevance for Pinning Models
Derrida, Bernard; Giacomin, Giambattista; Lacoin, Hubert; Toninelli, Fabio Lucio
2009-05-01
We study the critical point of directed pinning/wetting models with quenched disorder. The distribution K(·) of the location of the first contact of the (free) polymer with the defect line is assumed to be of the form K( n) = n - α-1 L( n), with α ≥ 0 and L(·) slowly varying. The model undergoes a (de)-localization phase transition: the free energy (per unit length) is zero in the delocalized phase and positive in the localized phase. For α 1, then quenched and annealed critical points differ whenever disorder is present, and we give the scaling form of their difference for small disorder. In agreement with the so-called Harris criterion, disorder is therefore relevant in this case. In the marginal case α = 1/2, under the assumption that L(·) vanishes sufficiently fast at infinity, we prove that the difference between quenched and annealed critical points, which is smaller than any power of the disorder strength, is positive: disorder is marginally relevant. Again, the case considered in [12,17] is out of our analysis and remains open. The results are achieved by setting the parameters of the model so that the annealed system is localized, but close to criticality, and by first considering a quenched system of size that does not exceed the correlation length of the annealed model. In such a regime we can show that the expectation of the partition function raised to a suitably chosen power {γ in (0, 1)} is small. We then exploit such an information to prove that the expectation of the same fractional power of the partition function goes to zero with the size of the system, a fact that immediately entails that the quenched system is delocalized.
Polyketide chain length control by chain length factor.
Tang, Yi; Tsai, Shiou-Chuan; Khosla, Chaitan
2003-10-22
Bacterial aromatic polyketides are pharmacologically important natural products. A critical parameter that dictates product structure is the carbon chain length of the polyketide backbone. Systematic manipulation of polyketide chain length represents a major unmet challenge in natural product biosynthesis. Polyketide chain elongation is catalyzed by a heterodimeric ketosynthase. In contrast to homodimeric ketosynthases found in fatty acid synthases, the active site cysteine is absent from the one subunit of this heterodimer. The precise role of this catalytically silent subunit has been debated over the past decade. We demonstrate here that this subunit is the primary determinant of polyketide chain length, thereby validating its designation as chain length factor. Using structure-based mutagenesis, we identified key residues in the chain length factor that could be manipulated to convert an octaketide synthase into a decaketide synthase and vice versa. These results should lead to novel strategies for the engineered biosynthesis of hitherto unidentified polyketide scaffolds.
Curve Length Estimation using Vertix Chain Code Curve Length Estimation
Habibollah Haron
2010-09-01
Full Text Available Most of the applications in image analysis are based on Freeman chain code. In this paper, for the first time, vertex chain code (VCC proposed by Bribiesca is applied to improve length estimation of the 2D digitized curve. The chain code has some preferences such as stable in shifting, turning, mirroring movement of image and has normalized starting point. Due to the variety of length estimator methods, we focused on the three specific techniques. First, the way Bribiesca proposed which is based on counting links between vertices; second, based on maximum length digital straight segments (DSSs and lastly local metrics. The results of these length estimators with the real perimeter are compared. Results thus obtained exhibits thatlength estimation using VCC is nearest to the actual length.
Universality of modulation length and time exponents.
Chakrabarty, Saurish; Dobrosavljević, Vladimir; Seidel, Alexander; Nussinov, Zohar
2012-10-01
We study systems with a crossover parameter λ, such as the temperature T, which has a threshold value λ(*) across which the correlation function changes from exhibiting fixed wavelength (or time period) modulations to continuously varying modulation lengths (or times). We introduce a hitherto unknown exponent ν(L) characterizing the universal nature of this crossover and compute its value in general instances. This exponent, similar to standard correlation length exponents, is obtained from motion of the poles of the momentum (or frequency) space correlation functions in the complex k-plane (or ω-plane) as the parameter λ is varied. Near the crossover (i.e., for λ→λ(*)), the characteristic modulation wave vector K(R) in the variable modulation length "phase" is related to that in the fixed modulation length "phase" q via |K(R)-q|[proportionality]|T-T(*)|(νL). We find, in general, that ν(L)=1/2. In some special instances, ν(L) may attain other rational values. We extend this result to general problems in which the eigenvalue of an operator or a pole characterizing general response functions may attain a constant real (or imaginary) part beyond a particular threshold value λ(*). We discuss extensions of this result to multiple other arenas. These include the axial next-nearest-neighbor Ising (ANNNI) model. By extending our considerations, we comment on relations pertaining not only to the modulation lengths (or times), but also to the standard correlation lengths (or times). We introduce the notion of a Josephson time scale. We comment on the presence of aperiodic "chaotic" modulations in "soft-spin" and other systems. These relate to glass-type features. We discuss applications to Fermi systems, with particular application to metal to band insulator transitions, change of Fermi surface topology, divergent effective masses, Dirac systems, and topological insulators. Both regular periodic and glassy (and spatially chaotic behavior) may be found in
Impedance of Finite Length Resistor
Krinsky, Samuel; Podobedov, Boris
2005-01-01
We determine the impedance of a cylindrical metal tube (resistor) of radius a and length g, attached at each end to perfect conductors of semi-infinite length. Our main interest is in the behavior of the impedance at high frequency (k>>1/a). In the equilibrium regime, ka2
Line Lengths and Starch Scores.
Moriarty, Sandra E.
1986-01-01
Investigates readability of different line lengths in advertising body copy, hypothesizing a normal curve with lower scores for shorter and longer lines, and scores above the mean for lines in the middle of the distribution. Finds support for lower scores for short lines and some evidence of two optimum line lengths rather than one. (SKC)
Gestation length in farmed reindeer.
Shipka, M P; Rowell, J E
2010-01-01
Reindeer (Rangifer tarandus tarundus) are the only cervids indigenous to the arctic environment. In Alaska, reindeer are a recognized agricultural species and an economic mainstay for many native populations. Traditionally raised in extensive free-ranging systems, a recent trend toward intensive farming requires a more in-depth knowledge of reproductive management. Reported gestation length in reindeer varies, ranging from 198 to 229 d in studies performed at the University of Alaska Fairbanks. A switchback study that manipulated only breeding date demonstrated a mean increase in gestation length of 8.5 d among females bred early in the season. The negative correlation between conception date and gestation length is consistent with reindeer research at other locations and reports of variable gestation length in a growing number of domestic and non-domestic species. This paper reviews the phenomenon in reindeer and discusses some of the factors known to affect gestation length as well as possible areas for future research.
Baer, Michael B
2008-01-01
Huffman coding finds an optimal prefix code for a given probability mass function. Consider situations in which one wishes to find an optimal code with the restriction that all codewords have lengths that lie in a user-specified set of lengths (or, equivalently, no codewords have lengths that lie in a complementary set). This paper introduces a polynomial-time dynamic programming algorithm that finds optimal codes for this reserved-length prefix coding problem. This has applications to quickly encoding and decoding lossless codes. In addition, one modification of the approach solves any quasiarithmetic prefix coding problem, while another finds optimal codes restricted to the set of codes with g codeword lengths for user-specified g (e.g., g=2).
Z-Scaling, Fractality and Principle of Relativity in Relativistic Collisions of Hadrons and Nuclei
Zborovský, I; Panebratsev, Yu A; Skoro, G P
2001-01-01
The formation length of particles produced in the relativistic collisions of hadrons and nuclei has relevance to the fundamental principles of physics at small interaction distances. The relation is phenomenologically expressed by a z-scaling observed in the differential cross sections for the inclusive reactions at high energies. The scaling variable reflects the length of the elementary particle trajectories in terms of a fractal measure. Characterizing the fractal approach, we demonstrate the relativity principle in space-time with broken isotropy. We derive relativistic transformations accounting for the asymmetry of space-time induced in the interactions by various parton fractal structures of hadrons and nuclei.
Flux saturation length of sediment transport.
Pähtz, Thomas; Kok, Jasper F; Parteli, Eric J R; Herrmann, Hans J
2013-11-22
Sediment transport along the surface drives geophysical phenomena as diverse as wind erosion and dune formation. The main length scale controlling the dynamics of sediment erosion and deposition is the saturation length Ls, which characterizes the flux response to a change in transport conditions. Here we derive, for the first time, an expression predicting Ls as a function of the average sediment velocity under different physical environments. Our expression accounts for both the characteristics of sediment entrainment and the saturation of particle and fluid velocities, and has only two physical parameters which can be estimated directly from independent experiments. We show that our expression is consistent with measurements of Ls in both aeolian and subaqueous transport regimes over at least 5 orders of magnitude in the ratio of fluid and particle density, including on Mars.
Minimum length-maximum velocity
Panes, Boris
2012-03-01
We study a framework where the hypothesis of a minimum length in space-time is complemented with the notion of reference frame invariance. It turns out natural to interpret the action of the obtained reference frame transformations in the context of doubly special relativity. As a consequence of this formalism we find interesting connections between the minimum length properties and the modified velocity-energy relation for ultra-relativistic particles. For example, we can predict the ratio between the minimum lengths in space and time using the results from OPERA on superluminal neutrinos.
On Fast Algorithm for Computing Even-Length DCT
Reznik, Yuriy A
2010-01-01
We study recursive algorithm for computing DCT of lengths $N=q 2^m$ ($m,q \\in \\mathbb{N}$, $q$ is odd) due to C.W.Kok. We show that this algorithm has the same multiplicative complexity as theoretically achievable by the prime factor decomposition, when $m \\leqslant 2$. We also show that C.W.Kok's factorization allows a simple conversion to a scaled form. We analyze complexity of such a scaled factorization, and show that for some lengths it achieves lower multiplicative complexity than one of known prime factor-based scaled transforms.
Chronobiology: relevance for tuberculosis.
Santos, Lígia Gabrielle; Pires, Gabriel Natan; Azeredo Bittencourt, Lia Rita; Tufik, Sergio; Andersen, Monica Levy
2012-07-01
Despite the knowledge concerning the pathogenesis of tuberculosis, this disease remains one of the most important causes of mortality worldwide. Several risk factors are well-known, such poverty, HIV infection, and poor nutrition, among others. However, some issues that may influence tuberculosis warrant further investigation. In particular, the chronobiological aspects related to tuberculosis have garnered limited attention. In general, the interface between tuberculosis and chronobiology is manifested in four ways: variations in vitamin D bioavailability, winter conditions, associated infections, and circannual oscillations of lymphocytes activity. Moreover, tuberculosis is related to the following chronobiological factors: seasonality, latitude, photoperiod and radiation. Despite the relevance of these topics, the relationship between them has been weakly reviewed. This review aims to synthesize the studies regarding the association between tuberculosis and chronobiology, as well as urge critical discussion and highlight its applicability to health policies for tuberculosis.
Longitudinal Changes in Leukocyte Telomere Length and Mortality in Humans
Bendix, Laila; Thinggaard, Mikael; Fenger, Mogens;
2014-01-01
Leukocyte telomere length (LTL) ostensibly shortens with age and has been moderately associated with mortality. In humans, these findings have come almost solely from cross-sectional studies. Only recently has LTL shortening within individuals been analyzed in longitudinal studies. Such studies...... are relevant to establish LTL dynamics as biomarkers of mortality as well as to disentangle the causality of telomeres on aging....
LU Yigang; PENG Jianxin; TONG Jie; DONG Yanwu
2000-01-01
On the basis of Jacobson's free length theory and the theory of pressure coefficient and temperature coefficient of free length in liquids, the relationship between the pressure coefficient of ultrasonic velocity and the pressure coefficient of free length, and the relationship between the temperature coefficient of ultrasonic velocity and the temperature coefficient of free length were studied. Relevant equations were given, and the pressure coefficient and temperature coefficient of ultrasonic velocity were calculated, which are in agreement with the measured values.
Pairing versus quarteting coherence length
Delion, Doru S
2015-01-01
We systematically analyse the coherence length in even-even nuclei. The pairing coherence length in the spin-singlet channel for the effective density dependent delta (DDD) and Gaussian interaction is estimated. We consider in our calculations bound states as well as narrow resonances. It turns out that the pairing gaps given by the DDD interaction are similar to those of the Gaussian potential if one renormalizes the radial width to the nuclear radius. The correlations induced by the pairing interaction have in all considered cases a long range character inside the nucleus and decrease towards the surface. The mean coherence length is larger than the geometrical radius for light nuclei and approaches this value for heavy nuclei. The effect of the temperature and states in continuum is investigated. Strong shell effects are evidenced, especially for protons. We generalize this concept to quartets by considering similar relations, but between proton and neutron pairs. The quartet coherence length has a similar...
Length Invisibilization of Tachyonic Neutrinos
Estakhr, Ahmad Reza
2016-09-01
Faster than the speed of light particle such as tachyonic neutrino due to its superluminal nature disapper and is undetectable. L = iΩ-1Lo where, i =√{ - 1 } is imaginary Number, Ω = 1 /√{βs2 - 1 } is Estakhr's Omega factor, L is the Superluminal Length, Lo is the proper length, βs =Vs / c > 1 is superluminal speed parameter, Vs is Superluminal velocity and c is speed of light.
Accurate aging of juvenile salmonids using fork lengths
Sethi, Suresh; Gerken, Jonathon; Ashline, Joshua
2017-01-01
Juvenile salmon life history strategies, survival, and habitat interactions may vary by age cohort. However, aging individual juvenile fish using scale reading is time consuming and can be error prone. Fork length data are routinely measured while sampling juvenile salmonids. We explore the performance of aging juvenile fish based solely on fork length data, using finite Gaussian mixture models to describe multimodal size distributions and estimate optimal age-discriminating length thresholds. Fork length-based ages are compared against a validation set of juvenile coho salmon, Oncorynchus kisutch, aged by scales. Results for juvenile coho salmon indicate greater than 95% accuracy can be achieved by aging fish using length thresholds estimated from mixture models. Highest accuracy is achieved when aged fish are compared to length thresholds generated from samples from the same drainage, time of year, and habitat type (lentic versus lotic), although relatively high aging accuracy can still be achieved when thresholds are extrapolated to fish from populations in different years or drainages. Fork length-based aging thresholds are applicable for taxa for which multiple age cohorts coexist sympatrically. Where applicable, the method of aging individual fish is relatively quick to implement and can avoid ager interpretation bias common in scale-based aging.
Elliptic Length Scales in Laminar, Two-Dimensional Supersonic Flows
2015-06-01
adiabatic wall flows over compression ramps and flows with shock impingements. The new correlations are derived from existing numerical data and...developed for 2D, laminar adiabatic wall flows over compression ramps and flows with shock impingements. These correlations are derived from existing...characterizing the influence of shocks and compression ramps on flat plate flows is presented. New correlations for laminar compressive interactions on
Length Scale and Gravity Effects on Microgravity Boiling Heat Transfer
Kim, Jungho; McQuillen, John; Balombin, Joe
2002-01-01
Boiling is a complex phenomenon where hydrodynamics, heat transfer, mass transfer, and interfacial phenomena are tightly interwoven. An understanding of boiling and critical heat flux in microgravity environments is of importance to space based hardware and processes such as heat exchange, cryogenic fuel storage and transportation, electronic cooling, and material processing due to the large amounts of heat that can be removed with relatively little increase in temperature. Although research in this area has been performed in the past four decades, the mechanisms by which heat is removed from surfaces in microgravity are still unclear. In earth gravity, buoyancy is an important parameter that affects boiling heat transfer through the rate at which bubbles are removed from the surface. A simple model describing the bubble departure size based on a quasistatic force balance between buoyancy and surface tension is given by the Fritz [I] relation: Bo(exp 1/2) = 0.0208 theta where Bo is the ratio between buoyancy and surface tension forces. For small, rapidly growing bubbles, inertia associated with the induced liquid motion can also cause bubble departure. In microgravity, the magnitude of effects related to natural convection and buoyancy are small and physical mechanisms normally masked by natural convection in earth gravity such as Marangoni convection can substantially influence the boiling and vapor bubble dynamics. CHF (critical heat transfer) is also substantially affected by microgravity. In 1 g environments, Bo has been used as a correlating parameter for CHF. Zuber's CHF model for an infinite horizontal surface assumes that vapor columns formed by the merger of bubbles become unstable due to a Helmholtz instability blocking the supply of liquid to the surface. The jets are spaced lambda(sub D) apart, where lambda(sub D) = 2pi square root of 3[(sigma)/(g(rho(sub l) - rho(sub v)](exp 1/2) = 2pi square root of 3 L Bo(exp -1/2) = square root of 3 lambda(sub c) and is the wavelength that amplifies most rapidly. The critical wavelength, lambda(sub c), is the wavelength below which a vapor layer underneath a liquid layer is stable. For heaters with Bo smaller than about 3 (heaters smaller than lambda(sub D)), the above model is not applicable, and surface tension effects dominate. Bubble coalescence is thought to be the mechanism for CHF under these conditions. Small Bo can result by decreasing the size of a heater in earth gravity, or by operating a large heater in a lower gravity environment. In the microgravity of space, even large heaters can have low Bo, and models based on Helmholtz instability should not be applicable. The macrolayer model of Haramura and Katto is dimensionally equivalent to Zuber's model and has the same dependence on gravity, so it should not be applicable as well. The goal of this work is to determine how boiling heat transfer mechanisms in a low-g environment are altered from those at higher gravity levels. Boiling data using a microheater array was obtained under gravity environments ranging from 1.8 g to 0.02 g with heater sizes ranging from 2.7 mm to 1 mm. The boiling behavior for 2.7 mm at 0.02 g looked quite similar to boiling on the 1 mm heater at 1 g-the formation of a large primary bubble surrounded by smaller satellite bubbles was observed under both conditions. The similarity suggests that for heaters smaller than some fraction of I(sub c), coalescence and surface tension dominate boiling heat transfer. It also suggests that microgravity boiling can be studied by studying boiling on very small heaters.
Coherent spectroscopies on ultrashort time and length scales
Schneider C.
2013-03-01
Full Text Available Three spectroscopic techniques are presented that provide simultaneous spatial and temporal resolution: modified confocal microscopy with heterodyne detection, space-time-resolved spectroscopy using coherent control concepts, and coherent two-dimensional nano-spectroscopy. Latest experimental results are discussed.
Length scale and manufacturability in density-based topology optimization
Lazarov, Boyan Stefanov; Wang, Fengwen; Sigmund, Ole
2016-01-01
Since its original introduction in structural design, density-based topology optimization has been applied to a number of other fields such as microelectromechanical systems, photonics, acoustics and fluid mechanics. The methodology has been well accepted in industrial design processes where it c......, well-defined designs with robust performances. The overview discusses the limitations, the advantages and the associated computational costs. The review is completed with optimized designs for minimum compliance, mechanism design and heat transfer.......Since its original introduction in structural design, density-based topology optimization has been applied to a number of other fields such as microelectromechanical systems, photonics, acoustics and fluid mechanics. The methodology has been well accepted in industrial design processes where it can...
Multi-length Scale Material Model Development for Armorgrade Composites
2014-05-02
synthesis -/processing-induced defects; (c) effect of 3 synthesis -/processing-induced defects on PPTA-fiber properties; (d) effect of fiber-/ yarn ...Derivation of the Materials Constitutive Relations for Carbon Nanotube Reinforced Poly-Vinyl-Ester-Epoxy Based Composites,” Journal of Materials Science, 42...fabric or PPTA-fiber-reinforced polymer-matrix composites. Specifically, the role of various material- synthesis -/fiber-processing-induced defects, as
Femtosecond structural dynamics on the atomic length scale
Zhang, Dongfang
2014-03-15
This thesis reports on the development and application of two different but complementary ultrafast electron diffraction setups built at the Max Planck Research Department for Structural Dynamics. One is an ultra-compact femtosecond electron diffraction (FED) setup (Egun300), which is currently operational (with a maximum electron energy of 150 keV) and provides ultrashort (∝300 fs) and bright (∝10 e/μm{sup 2}) electron bunches. The other one, named as Relativistic Electron Gun for Atomic Exploration (REGAE) is a radio frequency driven 2 to 5 MeV FED setup built in collaboration with different groups from DESY. REGAE was developed as a facility that will provide high quality diffraction with sufficient coherence to even address structural protein dynamics and with electron pulses as short as 20 fs (FWHM). As one of the first students in Prof. R.J. Dwayne Miller's group, I led the femtosecond (fs) laser sub-group at REGAE being responsible for the construction of different key optical elements required to drive both of aforementioned FED systems. A third harmonic generation (THG) and a nonlinear optical parametric amplifier (NOPA) have been used for the photo-generation of ultrashort electron bursts as well as sample laser excitation. Different diagnostic tools have been constructed to monitor the performance of the fs optical system. A fast autocorrelator was developed to provide on the fly pulse duration correction. A transient-grating frequency-resolved optical gating (TG-FROG) was built to obtain detail information about the characteristics of fs optical pulse, i.e. phase and amplitude of its spectral components. In addition to these optical setups, I developed a fs optical pump-probe system, which supports broadband probe pulses. This setup was successfully applied to investigate the semiconductor-to-metal photoinduced phase transition in VO{sub 2} and the ultrafast photo-reduction mechanism of graphene oxide. In regard to FED setups, I have been deeply involved in their development. I performed the first study in our compact FED system. I studied the optical and structural response of alkali halides to intense UV excitation conditions, i.e. above the damage threshold of the samples which required the application of a single-shot scheme. In order to gain a better understanding of the ablation process that follows fs optical excitation in alkali halides, I applied a variety of different techniques. Optical reflectivity, femtosecond electron diffraction, ion detection and crater measurements revealed the existence of a cold ablation process that occurs well below the threshold for plasma formation and even that for the melting point of the salts. This atypical cold explosion owes to the presence of highly localized excitonic states and reflects the repulsive nature of initial electronic correlations at play. In the case of REGAE, we performed the first time-resolved experiment following the fs laser heating dynamics and partial melting of polycrystalline gold films. This experiment was crucial to test the overall synchronization of our REGAE machine. We were able to observe a clear dynamics under single-shot photo-excitation conditions and found time zero within 1 picosecond. Further electron pulse characterization will involve the implementation of ponderomotive scattering. I have already constructed the required modular setup and performed all preliminary ASTRA N-body simulations.
何世柱; 王明文; 周军军; 石松
2011-01-01
The deep classification model is an effective paradigm for solving large-scale classification problems.An improved model was proposed based on the paradigm.First, a new method was used to evaluate the effectiveness of search stage independently.Second, the category and document information were collectively used to select category candidates.Finally, the classifier of Rocchio was trained based on the class centroid, and at the same time the information of related categories was used to determine the final category.Experiments on the corpus ODP show that the proposed approach outperforms the other new methods.%深层分类模型是一种解决大规模文本层次分类问题的有效范式.本文基于该范式提出一种改进型模型,首先将一种新方法用于单独评价搜索阶段的效果;然后利用类别和文档信息共同选择候选类别;最后基于类中心训练Rocchio分类器,同时利用相关类别的分类结果确定最终类别.在ODP数据集上的实验表明,相对于最新型的深层分类方法,该模型具有一定优势.
Hunt, Allen G; Ghanbarian, Behzad
2013-01-01
We apply our theory of conservative solute transport, based on concepts from percolation theory, directly and without modification to reactive solute transport. This theory has previously been shown to predict the observed range of dispersivity values for conservative solute transport over ten orders of magnitude of length scale. We now show that the temporal dependence derived for the solute velocity accurately predicts the time-dependence for the weathering of silicate minerals over nine orders of magnitude of time scale, while its predicted length dependence agrees with data obtained for reaction rates over five orders of magnitude of length scale. In both cases, it is possible to unify lab and field results. Thus, net reaction rates appear to be limited by solute transport velocities. We suggest the possible relevance of our results to landscape evolution of the earth's terrestrial surface.
Persistence Length of Stable Microtubules
Hawkins, Taviare; Mirigian, Matthew; Yasar, M. Selcuk; Ross, Jennifer
2011-03-01
Microtubules are a vital component of the cytoskeleton. As the most rigid of the cytoskeleton filaments, they give shape and support to the cell. They are also essential for intracellular traffic by providing the roadways onto which organelles are transported, and they are required to reorganize during cellular division. To perform its function in the cell, the microtubule must be rigid yet dynamic. We are interested in how the mechanical properties of stable microtubules change over time. Some ``stable'' microtubules of the cell are recycled after days, such as in the axons of neurons or the cilia and flagella. We measured the persistence length of freely fluctuating taxol-stabilized microtubules over the span of a week and analyzed them via Fourier decomposition. As measured on a daily basis, the persistence length is independent of the contour length. Although measured over the span of the week, the accuracy of the measurement and the persistence length varies. We also studied how fluorescently-labeling the microtubule affects the persistence length and observed that a higher labeling ratio corresponded to greater flexibility. National Science Foundation Grant No: 0928540 to JLR.
Inferring the Rate-Length Law of Protein Folding
Lane, Thomas J
2013-01-01
We investigate the rate-length scaling law of protein folding, a key undetermined scaling law in the analytical theory of protein folding. We demonstrate that chain length is a dominant factor determining folding times, and that the unambiguous determination of the way chain length corre- lates with folding times could provide key mechanistic insight into the folding process. Four specific proposed laws (power law, exponential, and two stretched exponentials) are tested against one an- other, and it is found that the power law best explains the data. At the same time, the fit power law results in rates that are very fast, nearly unreasonably so in a biological context. We show that any of the proposed forms are viable, conclude that more data is necessary to unequivocally infer the rate-length law, and that such data could be obtained through a small number of protein folding experiments on large protein domains.
CEBAF Upgrade Bunch Length Measurements
Ahmad, Mahmoud [Old Dominion Univ., Norfolk, VA (United States)
2016-05-01
Many accelerators use short electron bunches and measuring the bunch length is important for efficient operations. CEBAF needs a suitable bunch length because bunches that are too long will result in beam interruption to the halls due to excessive energy spread and beam loss. In this work, bunch length is measured by invasive and non-invasive techniques at different beam energies. Two new measurement techniques have been commissioned; a harmonic cavity showed good results compared to expectations from simulation, and a real time interferometer is commissioned and first checkouts were performed. Three other techniques were used for measurements and comparison purposes without modifying the old procedures. Two of them can be used when the beam is not compressed longitudinally while the other one, the synchrotron light monitor, can be used with compressed or uncompressed beam.
Keeping disease at arm's length
Lassen, Aske Juul
2015-01-01
active ageing change everyday life with chronic disease, and how do older people combine an active life with a range of chronic diseases? The participants in the study use activities to keep their diseases at arm’s length, and this distancing of disease at the same time enables them to engage in social...... and physical activities at the activity centre. In this way, keeping disease at arm’s length is analysed as an ambiguous health strategy. The article shows the importance of looking into how active ageing is practised, as active ageing seems to work well in the everyday life of the older people by not giving...... emphasis to disease. The article is based on ethnographic fieldwork and uses vignettes of four participants to show how they each keep diseases at arm’s length....
Validation of a novel ultrasound measurement of achilles tendon length
Barfod, Kristoffer Weisskirchner; Riecke, Anja Falk; Boesen, Anders
2014-01-01
PURPOSE: A clinically applicable and accurate method for measuring Achilles tendon length is needed to investigate the influence of elongation of the Achilles tendon after acute rupture. The purpose of this study was to develop and validate an ultrasonographic (US) length measurement...... of the Achilles tendon-aponeurosis complex. METHODS: Both legs of 19 non-injured subjects were examined by magnetic resonance imaging (MRI) and US. The length from calcaneus to the medial head of m. Gastrocnemius was measured by three independent US examiners. Repeated US measurements were performed and compared...... to be further assessed in the setting of acute Achilles tendon rupture. CLINICAL RELEVANCE: This new ultrasound measurement might allow for length measurement of ruptured Achilles tendons in the acute and chronic state after rupture. LEVEL OF EVIDENCE: II....
A nonparametric approach for relevance determination
Shahbaba, Babak
2010-01-01
The problem of evaluating a large number of factors in terms of their relevance to an outcome of interest arises in many research areas such as genetics, image processing, astrophysics, and neuroscience. In this paper, we argue that treating such problems as large-scale hypothesis testing does not reflect the usual motivation behind these studies, which is to select a subset of promising factors for further investigation. and leads investigators to rely on arbitrary selection mechanisms (e.g., setting the false discovery rate at 0.05) or unrealistic loss functions. Moreover, while we might be able to justify simplifying assumptions (e.g., parametric distributional forms for test statistics under the null and alternative hypotheses) for classic hypothesis testing situations (i.e., one hypothesis at a time), generalizing such assumptions to large-scale studies is restrictive and unnecessary. In accordance with the objective of such studies, we propose to treat them as relevance determination problems. This way,...
Traceability of high focal length cameras with diffractive optical elements
Lages Martins, L.; Silva Ribeiro, A.; Sousa, J. Alves e.
2016-11-01
This paper describes the use of diffractive optical elements (DOEs) for metrological traceable geometrical testing of high focal length cameras applied in the observation of large- scale structures. DOEs and related mathematical models are briefly explained. Laboratorial activities and results are described for the case of a high focal length camera used for longdistance displacement measurement of a long-span (2278 m) suspension bridge.
Casimir-Polder intermolecular forces in minimal length theories
Panella, O
2007-01-01
Generalized uncertainty relations are known to provide a minimal length $\\hbar\\sqrt{\\beta}$. The effect of such minimal length in the Casimir-Polder interactions between neutral atoms (molecules) is studied. The first order correction term in the minimal uncertainty parameter is derived and found to describe an attractive potential scaling as $r^{-9}$ as opposed to the well known $r^{-7}$ long range retarded potential.
Continuous lengths of oxide superconductors
Kroeger, Donald M.; List, III, Frederick A.
2000-01-01
A layered oxide superconductor prepared by depositing a superconductor precursor powder on a continuous length of a first substrate ribbon. A continuous length of a second substrate ribbon is overlaid on the first substrate ribbon. Sufficient pressure is applied to form a bound layered superconductor precursor powder between the first substrate ribbon and the second substrate ribbon. The layered superconductor precursor is then heat treated to establish the oxide superconducting phase. The layered oxide superconductor has a smooth interface between the substrate and the oxide superconductor.
Overview of bunch length measurements.
Lumpkin, A. H.
1999-02-19
An overview of particle and photon beam bunch length measurements is presented in the context of free-electron laser (FEL) challenges. Particle-beam peak current is a critical factor in obtaining adequate FEL gain for both oscillators and self-amplified spontaneous emission (SASE) devices. Since measurement of charge is a standard measurement, the bunch length becomes the key issue for ultrashort bunches. Both time-domain and frequency-domain techniques are presented in the context of using electromagnetic radiation over eight orders of magnitude in wavelength. In addition, the measurement of microbunching in a micropulse is addressed.
Hyperuniformity disorder length spectroscopy for extended particles
Durian, D. J.
2017-09-01
The concept of a hyperuniformity disorder length h was recently introduced for analyzing volume fraction fluctuations for a set of measuring windows [Chieco et al., Phys. Rev. E 96, 032909 (2017)., 10.1103/PhysRevE.96.032909]. This length permits a direct connection to the nature of disorder in the spatial configuration of the particles and provides a way to diagnose the degree of hyperuniformity in terms of the scaling of h and its value in comparison with established bounds. Here, this approach is generalized for extended particles, which are larger than the image resolution and can lie partially inside and partially outside the measuring windows. The starting point is an expression for the relative volume fraction variance in terms of four distinct volumes: that of the particle, the measuring window, the mean-squared overlap between particle and region, and the region over which particles have nonzero overlap with the measuring window. After establishing limiting behaviors for the relative variance, computational methods are developed for both continuum and pixelated particles. Exact results are presented for particles of special shape and for measuring windows of special shape, for which the equations are tractable. Comparison is made for other particle shapes, using simulated Poisson patterns. And the effects of polydispersity and image errors are discussed. For small measuring windows, both particle shape and spatial arrangement affect the form of the variance. For large regions, the variance scaling depends only on arrangement but particle shape sets the numerical proportionality. The combined understanding permit the measured variance to be translated to the spectrum of hyperuniformity lengths versus region size, as the quantifier of spatial arrangement. This program is demonstrated for a system of nonoverlapping particles at a series of increasing packing fractions as well as for an Einstein pattern of particles with several different extended shapes.
Inflation with a stringy minimal length, reworked
Palma, Gonzalo A
2009-01-01
In this paper we revisit the formulation of scalar field theories on de Sitter backgrounds subject to the generalized uncertainty principle (GUP). The GUP arises in several contexts in string theory, but is most readily thought of as resulting from using strings as effective probes of geometry, which suggests an uncertainty relation incorporating the string scale $l_s$. After reviewing the string theoretic case for the GUP, which implies a minimum length scale $l_s$, we follow in the footsteps of Kempf and concern ourselves as to how one might write down field theories which respect the GUP. We uncover a new representation of the GUP, which unlike previous studies, readily permits analytical solutions for the mode functions of a scalar field on de Sitter backgrounds. We find that scalar fields cannot be quantized on inflationary backgrounds with a Hubble radius $H^{-1}$ smaller than the string scale, implying a potential sub-planckian cutoff on the scale of inflation resulting from the GUP. We also compute or...
Self organisation of plasma turbulence: impact on radial correlation lengths
Ghendrih, Philippe; Dif-Pradalier, Guilhem; Norscini, Claudia; Cartier-Michaud, Thomas; Estève, Damien; Garbet, Xavier; Grandgirard, Virginie; Latu, Guillaume; Passeron, Chantal; Sarazin, Yanick
2014-11-01
The empirical scaling law used to support the projected ITER performance [1, 2] in analysed to determine the control parameters that must be considered in gyrokinetic simulations. The results of such an analysis are contradictory and do not appear to fit with present evidence from gyrokinetic simulations. Analysing the dependence of the correlation length on the ρ* parameter, we show that local values of the correlation length are governed by the shearing effect of the corrugation patterns, but that coarse graining this value, in time, radially or poloidally does not allow one to recover this match. A comparison to the scaling law must then rely on the scaling properties of the Probability Density Function of the correlation length that is found to exhibit heavy tails with algebraic decay.
Theory of stellar convection: Removing the Mixing-Length Parameter
Pasetto, S; Cropper, M; Grebel, E K
2014-01-01
Stellar convection is customarily described by Mixing-Length Theory, which makes use of the mixing-length scale to express the convective flux, velocity, and temperature gradients of the convective elements and stellar medium. The mixing-length scale is taken to be proportional to the local pressure scale height, and the proportionality factor (the mixing-length parameter) must be determined by comparing the stellar models to some calibrator, usually the Sun. No strong arguments exist to suggest that the mixing-length parameter is the same in all stars and at all evolutionary phases. Because of this, all stellar models in literature are hampered by this basic uncertainty. The aim of this study is to present a new theory of stellar convection that does not require the mixing length parameter. We present a self-consistent analytical formulation of stellar convection that determines the properties of stellar convection as a function of the physical behaviour of the convective elements themselves and the surround...
An Assessment of the Length and Variability of Mercury's Magnetotail
Milan, S. E.; Slavin, J. A.
2011-01-01
We employ Mariner 10 measurements of the interplanetary magnetic field in the vicinity of Mercury to estimate the rate of magnetic reconnection between the interplanetary magnetic field and the Hermean magnetosphere. We derive a time-series of the open magnetic flux in Mercury's magnetosphere. from which we can deduce the length of the magnetotail The length of the magnetotail is shown to be highly variable. with open field lines stretching between 15R(sub H) and 8S0R(sub H) downstream of the planet (median 150R(sub H)). Scaling laws allow the tail length at perihelion to be deduced from the aphelion Mariner 10 observations.
Length Normalization in XML Retrieval
Kamps, Jaap; Rijke, Maarten de; Sigurbjörnsson, Börkur
2005-01-01
The full paper appeared as: J. Kamps, M. de Rijke, and B. Sigurbj¨ornsson, “Length Normalization in XML Retrieval,” In: Proceedings 27th Annual International ACM SIGIR Conference (SIGIR 2004), pages 80-87, 2004.
Finite length Taylor Couette flow
Streett, C. L.; Hussaini, M. Y.
1987-01-01
Axisymmetric numerical solutions of the unsteady Navier-Stokes equations for flow between concentric rotating cylinders of finite length are obtained by a spectral collocation method. These representative results pertain to two-cell/one-cell exchange process, and are compared with recent experiments.
Administrator
from which stomachs were extracted for the analysis of the food contents, using frequency of occurrence, numerical and ... both fish species showed strong correlation between the weight and length with correlation coefficient (r) and ..... Basic data on the assessment of Sphyraena ... review of methods and their application.
Persistence length of dendronized polymers
Mikhailov, I.V.; Darinskii, A.A.; Zhulina, E.B.; Borisov, O.V.; Leermakers, F.A.M.
2015-01-01
We present numerical results for the thermodynamic rigidity and induced persistence length of dendronized polymers with systematically varied topology of their grafts obtained by the Scheutjens-Fleer self-consistent field method. The results were compared to predictions of an analytical mean-fiel
J. Vierinen
2011-06-01
Full Text Available We present a novel approach for modulating radar transmissions in order to improve target range and Doppler estimation accuracy. This is achieved by using non-uniform baud lengths. With this method it is possible to increase sub-baud range-resolution of phase coded radar measurements while maintaining a narrow transmission bandwidth. We first derive target backscatter amplitude estimation error covariance matrix for arbitrary targets when estimating backscatter in amplitude domain. We define target optimality and discuss different search strategies that can be used to find well performing transmission envelopes. We give several simulated examples of the method showing that fractional baud-length coding results in smaller estimation errors than conventional uniform baud length transmission codes when estimating the target backscatter amplitude at sub-baud range resolution. We also demonstrate the method in practice by analyzing the range resolved power of a low-altitude meteor trail echo that was measured using a fractional baud-length experiment with the EISCAT UHF system.
Cavity length below chute aerators
2008-01-01
It is proved that air entrainment is one of the efficient measures dealing with cavi-tation control for the release works of hydropower projects. There are many factors to be considered in designing a chute aerator. One of the most important factors concerns the cavity length below the aerator,which has outstanding effects on air entrainment against cavitation damage. It is crucial to determine reasonable emergence angle for the calculation of the cavity length. In the present paper the overall effects of structural and hydraulic parameters on the emergence angle of the flow from the aerator were analyzed. Four improved expressions of the emer-gence angle with weight coefficient were investigated through experimental data of 68 points observed from 12 aerators of 6 hydropower projects,of both model and prototype,on the basis of error theory. A method to calculate the cavity length be-low aerators was suggested,which considers overall effects of the above men-tioned parameters. Comparison between the method in this paper and the other five methods of calculating the cavity length showed that the present method is much more reliable than the existing methods while the mean error of the method is less than others.
Cavity length below chute aerators
WU JianHua; RUAN ShiPing
2008-01-01
It is proved that air entrainment is one of the efficient measures dealing with cavitation control for the release works of hydropower projects. There are many factors to be considered in designing a chute aerator. One of the most important factors concerns the cavity length below the aerator, which has outstanding effects on air entrainment against cavitation damage. It is crucial to determine reasonable emergence angle for the calculation of the cavity length. In the present paper the overall effects of structural and hydraulic parameters on the emergence angle of the flow from the aerator were analyzed. Four improved expressions of the emergence angle with weight coefficient were investigated through experimental data of 68 points observed from 12 aerators of 6 hydropower projects, of both model and prototype, on the basis of error theory. A method to calculate the cavity length below aerators was suggested, which considers overall effects of the above mentioned parameters. Comparison between the method in this paper and the other five methods of calculating the cavity length showed that the present method is much more reliable than the existing methods while the mean error of the method is less than others.
Manju Pruthi
2001-11-01
In this paper explicit expressions of + 1 idempotents in the ring $R = F_q[X]/\\langle X^{2^m}-1\\rangle$ are given. Cyclic codes of length 2 over the finite field , of odd characteristic, are defined in terms of their generator polynomials. The exact minimum distance and the dimension of the codes are obtained.