WorldWideScience

Sample records for release significant quantities

  1. DELPHI expert panel evaluation of Hanford high level waste tank failure modes and release quantities

    Energy Technology Data Exchange (ETDEWEB)

    Dunford, G.L.; Han, F.C.

    1996-09-30

    The Failure Modes and Release Quantities of the Hanford High Level Waste Tanks due to postulated accident loads were established by a DELPHI Expert Panel consisting of both on-site and off-site experts in the field of Structure and Release. The Report presents the evaluation process, accident loads, tank structural failure conclusion reached by the panel during the two-day meeting.

  2. Zinc release from Schaffer collaterals and its significance.

    Science.gov (United States)

    Takeda, Atsushi; Nakajima, Satoko; Fuke, Sayuri; Sakurada, Naomi; Minami, Akira; Oku, Naoto

    2006-02-15

    On the basis of the evidence that approximately 45% of Schaffer collateral boutons are zinc-positive, zinc release from Schaffer collaterals and its action were examined in hippocampal slices. When zinc release from Schaffer collaterals was examined using ZnAF-2, a membrane-impermeable zinc indicator, ZnAF-2 signal in the stratum radiatum of the CA1 was increased by tetanic stimuli at 100 Hz for 1s, suggesting that zinc is released from Schaffer collaterals in a calcium- and impulse-dependent manner. An in vivo microdialysis experiment indicated that the perfusion with 10 microM zinc significantly decreases extracellular glutamate concentration in the CA1. When tetanic stimuli at 100 Hz for 5s were delivered to the dentate granule cells, the increase in calcium signal in the stratum radiatum of the CA1, as well as in the stratum lucidum of the CA3, was attenuated by addition of 10 microM zinc, while enhanced by addition of 1mM CaEDTA, a membrane-impermeable zinc chelator. The increase in calcium signal in the CA1, in which Schaffer collateral synapses exist, during delivery of tetanic stimuli at 100 Hz for 1s to the Schaffer collateral-commissural pathway was also significantly enhanced by addition of 1mM CaEDTA. These results suggest that zinc released from Schaffer collaterals suppressively modulates presynaptic and postsynaptic calcium signaling in the CA1, followed by the suppression of glutamate release.

  3. Definition, significance and measurement of quantities pertaining to the oxygen carrying properties of human blood

    NARCIS (Netherlands)

    Zijlstra, WG; Maas, AHJ; Moran, RF

    1996-01-01

    A consistent set of definitions is given of the principal quantities pertaining to the oxygen transport by the blood, and of their mutual relationships, in relation to the methods used in their measurement. At the core is the correct definition of oxygen saturation, the deviation of which has

  4. The Dynamics of Pheromone Gland Synthesis and Release: a Paradigm Shift for Understanding Sex Pheromone Quantity in Female Moths.

    Science.gov (United States)

    Foster, Stephen P; Anderson, Karin G; Casas, Jérôme

    2018-05-10

    Moths are exemplars of chemical communication, especially with regard to specificity and the minute amounts they use. Yet, little is known about how females manage synthesis and storage of pheromone to maintain release rates attractive to conspecific males and why such small amounts are used. We developed, for the first time, a quantitative model, based on an extensive empirical data set, describing the dynamical relationship among synthesis, storage (titer) and release of pheromone over time in a moth (Heliothis virescens). The model is compartmental, with one major state variable (titer), one time-varying (synthesis), and two constant (catabolism and release) rates. The model was a good fit, suggesting it accounted for the major processes. Overall, we found the relatively small amounts of pheromone stored and released were largely a function of high catabolism rather than a low rate of synthesis. A paradigm shift may be necessary to understand the low amounts released by female moths, away from the small quantities synthesized to the (relatively) large amounts catabolized. Future research on pheromone quantity should focus on structural and physicochemical processes that limit storage and release rate quantities. To our knowledge, this is the first time that pheromone gland function has been modeled for any animal.

  5. Estimated quantity of mercury in amalgam waste water residue released by dentists into the sewerage system in Ontario, Canada.

    Science.gov (United States)

    Adegbembo, Albert O; Watson, Philip A

    2004-12-01

    To estimate the quantity of dental amalgam that Ontario dentists release into waste water. Information from a self-administered postal survey of Ontario dentists was combined with the results of other experiments on the weight of amalgam restorations and the quantity of amalgam waste that bypasses solids separators in dental offices. Algorithms were developed to compute the quantity of amalgam waste leaving dental offices when dentists used or did not use ISO 11143 amalgam particle separators. A total of 878 (44.0%) of 1,994 sampled dentists responded to the survey. It was estimated that Ontario dentists removed 1,880.32 kg of amalgam (940.16 kg of mercury) during 2002, of which 1,128.19 kg of amalgam (564.10 kg of mercury) would have been released into waste water in Ontario if no dentists had been using a separator. Approximately 22% of the dentists reported using amalgam particle separators. On the basis of current use of amalgam separators, it was estimated that 861.78 kg of amalgam (430.89 kg of mercury or 170.72 mg per dentist daily) was released in 2002. The use of amalgam separators by all dentists could reduce the quantity of amalgam (and mercury) entering waste water to an estimated 12.41 kg (6.21 kg of mercury, or 2.46 mg per dentist per day). Amalgam particles separators can dramatically reduce amalgam and mercury loading in waste water released from dental offices.

  6. Heat shock protein 72: release and biological significance during exercise.

    Science.gov (United States)

    Whitham, Martin; Fortes, Matthew Benjamin

    2008-01-01

    The cumulative stressors of exercise manifest themselves at a cellular level by threatening the protein homeostasis of the cell. In these conditions, Heat Shock Proteins (HSP) are synthesised to chaperone mis-folded and denatured proteins. As such, the intracellular HSP response is thought to aid cell survival in the face of otherwise lethal cellular stress. Recently, the inducible isoform of the 70 Kda heat shock protein family, Hsp72 has been detected in the extracellular environment. Furthermore, the release of this protein into the circulation has been shown to occur in response to a range of exercise bouts. The present review summarises the current research on the exercise Hsp72 response, the possible mediators and mechanisms of extracellular (e)Hsp72 release, and the possible biological significance of this systemic response. In particular, the possible role of eHsp72 in the modulation of immunity during exercise is discussed.

  7. Determination of the Quantity of I-135 Released from the AGR Experiment Series

    International Nuclear Information System (INIS)

    Scates, Dawn M.; Walter, John B.; Reber, Edward L.; Sterbentz, James W.; Petti, David A.

    2014-01-01

    A series of three Advanced Gas Reactor (AGR) experiments have been conducted in the Advanced Test Reactor (ATR) at Idaho National Laboratory (INL). From 2006 through 2014, these experiments supported the development and qualification of the new U.S. tri-structural isotropic (TRISO) particle fuel for Very High Temperature Reactors (VHTR). Each AGR experiment consisted of multiple fueled capsules, each plumbed for independent temperature control using a mix of helium and neon gases. The gas leaving a capsule was routed to individual Fission Product Monitor (FPM) detectors. For intact fuel particles, the TRISO particle coatings provide a substantial barrier to fission product release. However, particles with failed coatings, whether because of a minute percentage of initially defective particles, those which fail during irradiation, or those designed-to-fail (DTF) particles, can release fission products to the flowing gas stream. Because reactive fission product elements like iodine and cesium quickly deposit on cooler capsule components and piping structures as the effluent gas leaves the reactor core, only the noble fission gas isotopes of Kr and Xe tend to reach FPM detectors. The FPM system utilizes High Purity Germanium (HPGe) detectors coupled with a thallium activated sodium iodide NaI(Tl) scintillator. The germanium detector provides individual isotopic information, while the NaI(Tl) scintillator is used as a gross count rate meter. During irradiation, the "1"3"5"mXe concentration reaching the FPM detectors is from both direct fission and by decay of the accumulated "1"3"5I. About ~2.5 hours after irradiation (ten 15.3 minute "1"3"5mXe half-lives) the directly produced "1"3"5"mXe has decayed and only the longer lived "1"3"5I remains as a source. Decay systematics dictate that "1"3"5"mXe will be in secular equilibrium with its "1"3"5I parent, such that it’s production rate very nearly equals the decay rate of the parent, and its concentration in the flowing

  8. [Significance of lateral release in the therapy of patellar chondromalacia].

    Science.gov (United States)

    Krüger, T; Göbel, F; Huschenbett, A; Hein, W

    2002-10-01

    A retrospective study was performed in 26 patients who underwent an operation for femoro-patellar pain due to a patellar chondromalacia with or without minor patellar dislocation/lateral pressure syndrome. The average age of the patients was 28.5 (15-39) years. 22 of the 26 patients revealed minor chondral damages of the stages 1 and 2 according to Outerbridge. In 12 patients ("lavage" group), an arthroscopic joint debridement only was carried out, while an additional open, lateral retinaculum release was made in 14 patients ("lateral release" group). The patella's distance of dislocation according to Hepp was reduced on an average of 3.0 (0-7) mm (p = 0.0019). The results of Bentley's score obtained during the follow-up interval on an average of 30.1 (9 to 60) months were almost identical for both groups. "Good" and "very good" results were achieved in the "lavage" group (83.3 %) and "lateral release" group (78.6 % of the patients). Lateral release should be used in cases of patellar decentration between 5 and 10 mm and adequate pain symptoms. The post-operative distance of dislocation should be less than 5 mm. Under such conditions and with minor chondral damage, a combined approach by using an arthroscopic joint debridement and open lateral release is promising to treat a patellar dislocation/lateral pressure syndrome.

  9. Quantity Surveying Undergraduates’ Awareness on Cost Significant of High-Rise Condominium Projects in Malaysia: The Case of a Private University in Malaysia

    OpenAIRE

    Peng Lee Wah; Seng Ng See; Choon Toh Tien; Sim Lim Cheng; Khian Yong Ching; Chen Goh Kai

    2016-01-01

    Recent developments in quantity surveying (QS) emphasised the importance of identifying cost significant elements (CSE). The knowledge on CSE of high-rise condominium projects (HRCP) is essential as high-rise residential multi-unit projects are the next option in building construction due to limited land areas in urban areas. This study aims to determine the levels of awareness among QS undergraduates of a private university in Malaysia on CSE of HRCP in Malaysia. The respondents’ knowledge o...

  10. Preliminary investigations of the significance of the ingestion pathway following accidental releases with actinides

    International Nuclear Information System (INIS)

    Steinhauer, C.

    1985-10-01

    Preliminary accident consequence assessments have been performed with the computer code UFOMOD to study the significance of the ingestion pathway in accidental releases with actinides. The investigation was based on the release category K1 of the 'Risk Oriented Analysis of the SNR 300', in which a higher fraction of actinides is released than in the worst release category for an LWR. The analysis was carried out using the currently implemented food chain transport model WASH-1400/BSU and data from the dynamic model from the MARC methodology. To study the influence of the time of the accident on the food chain-related results, releases in January and July were considered by means of the MARC data. In this report the differences are presented between both food chain transport models for transuranium elements and those which are observed in the potential doses due to ingestion, the areas affected by food-bans and the late health effects when using both models and taking the influence of the season into account. (orig./HP) [de

  11. Quantity Surveying Undergraduates’ Awareness on Cost Significant of High-Rise Condominium Projects in Malaysia: The Case of a Private University in Malaysia

    Directory of Open Access Journals (Sweden)

    Peng Lee Wah

    2016-01-01

    Full Text Available Recent developments in quantity surveying (QS emphasised the importance of identifying cost significant elements (CSE. The knowledge on CSE of high-rise condominium projects (HRCP is essential as high-rise residential multi-unit projects are the next option in building construction due to limited land areas in urban areas. This study aims to determine the levels of awareness among QS undergraduates of a private university in Malaysia on CSE of HRCP in Malaysia. The respondents’ knowledge on CSE has not achieved a satisfactory level. Both male and female respondents have the same levels of awareness on CSE. Remedial strategies to improve this situation are recommended.

  12. A method for release and multiple strand amplification of small quantities of DNA from endospores of the fastidious bacterium Pasteuria penetrans.

    Science.gov (United States)

    Mauchline, T H; Mohan, S; Davies, K G; Schaff, J E; Opperman, C H; Kerry, B R; Hirsch, P R

    2010-05-01

    To establish a reliable protocol to extract DNA from Pasteuria penetrans endospores for use as template in multiple strand amplification, thus providing sufficient material for genetic analyses. To develop a highly sensitive PCR-based diagnostic tool for P. penetrans. An optimized method to decontaminate endospores, release and purify DNA enabled multiple strand amplification. DNA purity was assessed by cloning and sequencing gyrB and 16S rRNA gene fragments obtained from PCR using generic primers. Samples indicated to be 100%P. penetrans by the gyrB assay were estimated at 46% using the 16S rRNA gene. No bias was detected on cloning and sequencing 12 housekeeping and sporulation gene fragments from amplified DNA. The detection limit by PCR with Pasteuria-specific 16S rRNA gene primers following multiple strand amplification of DNA extracted using the method was a single endospore. Generation of large quantities DNA will facilitate genomic sequencing of P. penetrans. Apparent differences in sample purity are explained by variations in 16S rRNA gene copy number in Eubacteria leading to exaggerated estimations of sample contamination. Detection of single endospores will facilitate investigations of P. penetrans molecular ecology. These methods will advance studies on P. penetrans and facilitate research on other obligate and fastidious micro-organisms where it is currently impractical to obtain DNA in sufficient quantity and quality.

  13. Iodine-131 Releases from Radioactive Lanthanum Processing at the X-10 Site in Oak Ridge, Tennessee (1944-1956)- An Assessment of Quantities released, Off-Site Radiation Doses, and Potential Excess Risks of Thyroid Cancer, Volume 1

    International Nuclear Information System (INIS)

    Apostoaei, A.I.; Burns, R.E.; Hoffman, F.O.; Ijaz, T.; Lewis, C.J.; Nair, S.K.; Widner, T.E.

    1999-01-01

    In the early 1990s, concern about the Oak Ridge Reservation's past releases of contaminants to the environment prompted Tennessee's public health officials to pursue an in-depth study of potential off-site health effects at Oak Ridge. This study, the Oak Ridge dose reconstruction, was supported by an agreement between the U.S. Department of Energy (DOE) and the State of Tennessee, and was overseen by a 12-member panel appointed by Tennessee's Commissioner of Health. One of the major contaminants studied in the dose reconstruction was radioactive iodine, which was released to the air by X-10 (now called Oak Ridge National Laboratory) as it processed spent nuclear reactor fuel from 1944 through 1956. The process recovered radioactive lanthanum for use in weapons development. Iodine concentrates in the thyroid gland so health concerns include various diseases of the thyroid, such as thyroid cancer. The large report, ''Iodine-131 Releases from Radioactive Lanthanum Processing at the X-10 Site in Oak Ridge, Tennessee (1944-1956) - An Assessment of Quantities Released, Off-site Radiation Doses, and Potential Excess Risks of Thyroid Cancer,'' is in two volumes. Volume 1 is the main body of the report, and Volume 1A, which has the same title, consists of 22 supporting appendices. Together, these reports serve the following purposes: (1) describe the methodologies used to estimate the amount of iodine-131 (I-131) released; (2) evaluate I-131's pathway from air to vegetation to food to humans; (3) estimate doses received by human thyroids; (4) estimate excess risk of acquiring a thyroid cancer during ones lifetime; and (5) provide equations, examples of historical documents used, and tables of calculated values. Results indicate that females born in 1952 who consumed milk from a goat pastured a few miles east of X-10 received the highest doses from I-131 and would have had the highest risks of contracting thyroid cancer. Doses from cow's milk are considerably less . Detailed

  14. Iodine-131 Releases from Radioactive Lanthanum Processing at the X-10 Site in Oak Ridge, Tennessee (1944-1956)- An Assessment of Quantities released, Off-Site Radiation Doses, and Potential Excess Risks of Thyroid Cancer, Volume 1

    Energy Technology Data Exchange (ETDEWEB)

    Apostoaei, A.I.; Burns, R.E.; Hoffman, F.O.; Ijaz, T.; Lewis, C.J.; Nair, S.K.; Widner, T.E.

    1999-07-01

    In the early 1990s, concern about the Oak Ridge Reservation's past releases of contaminants to the environment prompted Tennessee's public health officials to pursue an in-depth study of potential off-site health effects at Oak Ridge. This study, the Oak Ridge dose reconstruction, was supported by an agreement between the U.S. Department of Energy (DOE) and the State of Tennessee, and was overseen by a 12-member panel appointed by Tennessee's Commissioner of Health. One of the major contaminants studied in the dose reconstruction was radioactive iodine, which was released to the air by X-10 (now called Oak Ridge National Laboratory) as it processed spent nuclear reactor fuel from 1944 through 1956. The process recovered radioactive lanthanum for use in weapons development. Iodine concentrates in the thyroid gland so health concerns include various diseases of the thyroid, such as thyroid cancer. The large report, ''Iodine-131 Releases from Radioactive Lanthanum Processing at the X-10 Site in Oak Ridge, Tennessee (1944-1956) - An Assessment of Quantities Released, Off-site Radiation Doses, and Potential Excess Risks of Thyroid Cancer,'' is in two volumes. Volume 1 is the main body of the report, and Volume 1A, which has the same title, consists of 22 supporting appendices. Together, these reports serve the following purposes: (1) describe the methodologies used to estimate the amount of iodine-131 (I-131) released; (2) evaluate I-131's pathway from air to vegetation to food to humans; (3) estimate doses received by human thyroids; (4) estimate excess risk of acquiring a thyroid cancer during ones lifetime; and (5) provide equations, examples of historical documents used, and tables of calculated values. Results indicate that females born in 1952 who consumed milk from a goat pastured a few miles east of X-10 received the highest doses from I-131 and would have had the highest risks of contracting thyroid cancer. Doses from cow

  15. 76 FR 71583 - Notice of Availability of Finding of No Significant Impact for Field Release of Insects for...

    Science.gov (United States)

    2011-11-18

    ... Finding of No Significant Impact for Field Release of Insects for Biological Control of Carrizo Cane... insects, the Arundo scale and the Arundo wasp as biological control agents for the non-native and invasive... [[Page 71584

  16. Significance of air humidity and air velocity for fungal spore release into the air

    Science.gov (United States)

    Pasanen, A.-L.; Pasanen, P.; Jantunen, M. J.; Kalliokoski, P.

    Our previous field studies have shown that the presence of molds in buildings does not necessarily mean elevated airborne spore counts. Therefore, we investigated the release of fungal spores from cultures of Aspergillus fumigatus, Penicillium sp. and Cladosporium sp. at different air velocities and air humidities. Spores of A. fumigatus and Penicillium sp. were released from conidiophores already at air velocity of 0.5 ms -1, whereas Cladosporium spores required at least a velocity of 1.0 ms -1. Airborne spore counts of A. fumigatus and Penicillium sp. were usually higher in dry than moist air, being minimal at relative humidities (r.h.) above 70%, while the effect of r.h. on the release of Cladosporium sp. was ambivalent. The geometric mean diameter of released spores increased when the r.h. exceeded a certain level which depends on fungal genus. Thus, spores of all three fungi were hygroscopic but the hygroscopicity of various spores appeared at different r.h.-ranges. This study indicates that spore release is controlled by external factors and depends on fungal genus which can be one reason for considerable variation of airborne spore counts in buildings with mold problems.

  17. Emission sources and quantities

    International Nuclear Information System (INIS)

    Heinen, B.

    1991-01-01

    The paper examines emission sources and quantities for SO 2 and NO x . Natural SO 2 is released from volcanic sources and to a much lower extent from marsh gases. In nature NO x is mainly produced in the course of the chemical and bacterial denitrification processes going on in the soil. Manmade pollutants are produced in combustion processes. The paper concentrates on manmade pollution. Aspects discussed include: mechanism of pollution development; manmade emission sources (e.g. industry, traffic, power plants and domestic sources); and emission quantities and forecasts. 11 refs., 2 figs., 5 tabs

  18. Anchoring cationic amphiphiles for nucleotide delivery: significance of DNA release from cationic liposomes for transfection.

    Science.gov (United States)

    Hirashima, Naohide; Minatani, Kazuhiro; Hattori, Yoshifumi; Ohwada, Tomohiko; Nakanishi, Mamoru

    2007-06-01

    We have designed and synthesized lithocholic acid-based cationic amphiphile molecules as components of cationic liposomes for gene transfection (lipofection). To study the relationship between the molecular structures of those amphiphilic molecules, particularly the extended hydrophobic appendant (anchor) at the 3-hydroxyl group, and transfection efficiency, we synthesized several lithocholic and isolithocholic acid derivatives, and examined their transfection efficiency. We also compared the physico-chemical properties of cationic liposomes prepared from these derivatives. We found that isolithocholic acid derivatives exhibit higher transfection efficiency than the corresponding lithocholic acid derivatives. This result indicates that the orientation and extension of hydrophobic regions influence the gene transfection process. Isolithocholic acid derivatives showed a high ability to encapsulate DNA in a compact liposome-DNA complex and to protect it from enzymatic degradation. Isolithocholic acid derivatives also facilitated the release of DNA from the liposome-DNA complex, which is a crucial step for DNA entry into the nucleus. Our results show that the transfection efficiency is directly influenced by the ability of the liposome complex to release DNA, rather than by the DNA-encapsulating ability. Molecular modeling revealed that isolithocholic acid derivatives take relatively extended conformations, while the lithocholic acid derivatives take folded structures. Thus, the efficiency of release of DNA from cationic liposomes in the cytoplasm, which contributes to high transfection efficiency, appears to be dependent upon the molecular shape of the cationic amphiphiles.

  19. Evaluation of the potential for significant ammonia releases from Hanford waste tanks

    International Nuclear Information System (INIS)

    Palmer, B.J.; Anderson, C.M.; Chen, G.; Cuta, J.M.; Ferryman, T.A.; Terrones, G.

    1996-07-01

    Ammonia is ubiquitous as a component of the waste stored in the Hanford Site single-shell tanks (SSTs) and double-shell tanks (DSTs). Because ammonia is both flammable and toxic, concerns have been raised about the amount of ammonia stored in the tanks and the possible mechanisms by which it could be released from the waste into the head space inside the tanks as well as into the surrounding atmosphere. Ammonia is a safety issue for three reasons. As already mentioned, ammonia is a flammable gas and may contribute to a flammability hazard either directly, if it reaches a high enough concentration in the tank head space, or by contributing to the flammability of other flammable gases such as hydrogen (LANL 1994). Ammonia is also toxic and at relatively low concentrations presents a hazard to human health. The level at which ammonia is considered Immediately Dangerous to Life or Health (IDLH) is 300 ppm (WHC 1993, 1995). Ammonia concentrations at or above this level have been measured inside the head space in a number of SSTs. Finally, unlike hydrogen and nitrous oxide, ammonia is highly soluble in aqueous solutions, and large amounts of ammonia can be stored in the waste as dissolved gas. Because of its high solubility, ammonia behaves in a qualitatively different manner from hydrogen or other insoluble gases. A broader range of scenarios must be considered in modeling ammonia storage and release

  20. The radiological significance of transuranium radioisotopes released to the environment during operation of the LMFBR fuel cycle

    International Nuclear Information System (INIS)

    Barr, N.F.

    1976-01-01

    Estimates based on current knowledge and conservative assumptions indicate that release of transuranium elements from the Liquid Metal Fast Breeder Reactor (LMFBR) fuel cycle are likely to proaduce population dose commitments small compared to those produced by naturally occurring alpha emitters and globally dispersed transuranium radioisotopes from tests of nuclear weapons in the atmosphere. Potential health consequences of these releases to current and future generations are estimated to be very small compared to risks associated with the production of energy by fossil fuels. The estimates are subject to a number of uncertainties imposed by lack of knowledge. Some of the uncertainties are not likely to be greatly reduced until LMFBR facilities are designed and operated. Others may be significantly reduced prior to facility design and operation. The paper discusses the sensitivity of the estimates to uncertainties and approches to reducing those uncertainties that strongly influence the estimates. (author)

  1. Inhibition of basophil histamine release by gangliosides. Further studies on the significance of cell membrane sialic acid in the histamine release process

    DEFF Research Database (Denmark)

    Jensen, C; Norn, S; Thastrup, Ole

    1987-01-01

    with the glucolipid mixture increased the sialic acid content of the cells, and this increase was attributed to an insertion of gangliosides into the cell membrane. The inhibition of histamine release was abolished by increasing the calcium concentration, which substantiates our previous findings that cell membrane......Histamine release from human basophils was inhibited by preincubation of the cells with a glucolipid mixture containing sialic acid-containing gangliosides. This was true for histamine release induced by anti-IgE, Concanavalin A and the calcium ionophore A23187, whereas the release induced by S....... aureus Wood 46 was not affected. It was demonstrated that the inhibitory capacity of the glucolipid mixture could be attributed to the content of gangliosides, since no inhibition was obtained with cerebrosides or with gangliosides from which sialic acid was removed. Preincubation of the cells...

  2. Dermal application of nitric oxide releasing acidified nitrite-containing liniments significantly reduces blood pressure in humans.

    Science.gov (United States)

    Opländer, Christian; Volkmar, Christine M; Paunel-Görgülü, Adnana; Fritsch, Thomas; van Faassen, Ernst E; Mürtz, Manfred; Grieb, Gerrit; Bozkurt, Ahmet; Hemmrich, Karsten; Windolf, Joachim; Suschek, Christoph V

    2012-02-15

    Vascular ischemic diseases, hypertension, and other systemic hemodynamic and vascular disorders may be the result of impaired bioavailability of nitric oxide (NO). NO but also its active derivates like nitrite or nitroso compounds are important effector and signal molecules with vasodilating properties. Our previous findings point to a therapeutical potential of cutaneous administration of NO in the treatment of systemic hemodynamic disorders. Unfortunately, no reliable data are available on the mechanisms, kinetics and biological responses of dermal application of nitric oxide in humans in vivo. The aim of the study was to close this gap and to explore the therapeutical potential of dermal nitric oxide application. We characterized with human skin in vitro and in vivo the capacity of NO, applied in a NO-releasing acidified form of nitrite-containing liniments, to penetrate the epidermis and to influence local as well as systemic hemodynamic parameters. We found that dermal application of NO led to a very rapid and significant transepidermal translocation of NO into the underlying tissue. Depending on the size of treated skin area, this translocation manifests itself through a significant systemic increase of the NO derivates nitrite and nitroso compounds, respectively. In parallel, this translocation was accompanied by an increased systemic vasodilatation and blood flow as well as reduced blood pressure. We here give evidence that in humans dermal application of NO has a therapeutic potential for systemic hemodynamic disorders that might arise from local or systemic insufficient availability of NO or its bio-active NO derivates, respectively. Copyright © 2012 Elsevier Inc. All rights reserved.

  3. Extended-release niacin/laropiprant significantly improves lipid levels in type 2 diabetes mellitus irrespective of baseline glycemic control

    Directory of Open Access Journals (Sweden)

    Bays HE

    2015-02-01

    Full Text Available Harold E Bays,1 Eliot A Brinton,2 Joseph Triscari,3 Erluo Chen,3 Darbie Maccubbin,3 Alexandra A MacLean,3 Kendra L Gibson,3 Rae Ann Ruck,3 Amy O Johnson-Levonas,3 Edward A O’Neill,3 Yale B Mitchel3 1Louisville Metabolic & Atherosclerosis Research Center (L-MARC, Louisville, KY, USA; 2Utah Foundation for Biomedical Research, Salt Lake City, UT, USA; 3Merck & Co, Inc., Whitehouse Station, NJ, USA Background: The degree of glycemic control in patients with type 2 diabetes mellitus (T2DM may alter lipid levels and may alter the efficacy of lipid-modifying agents. Objective: Evaluate the lipid-modifying efficacy of extended-release niacin/laropiprant (ERN/LRPT in subgroups of patients with T2DM with better or poorer glycemic control. Methods: Post hoc analysis of clinical trial data from patients with T2DM who were randomized 4:3 to double-blind ERN/LRPT or placebo (n=796, examining the lipid-modifying effects of ERN/LRPT in patients with glycosylated hemoglobin or fasting plasma glucose levels above and below median baseline levels. Results: At Week 12 of treatment, ERN/LRPT significantly improved low-density lipoprotein cholesterol, high-density lipoprotein cholesterol (HDL-C, non-high-density lipoprotein cholesterol, triglycerides, and lipoprotein (a, compared with placebo, with equal efficacy in patients above or below median baseline glycemic control. Compared with placebo, over 36 weeks of treatment more patients treated with ERN/LRPT had worsening of their diabetes and required intensification of antihyperglycemic medication, irrespective of baseline glycemic control. Incidences of other adverse experiences were generally low in all treatment groups. Conclusion: The lipid-modifying effects of ERN/LRPT are independent of the degree of baseline glycemic control in patients with T2DM (NCT00485758. Keywords: lipid-modifying agents, hyperglycemia, LDL, HDL, triglycerides

  4. Radiation quantities and units

    International Nuclear Information System (INIS)

    2013-01-01

    This fifth chapter presents the conceptual evolution, the definition procedures, the radiological quantities themselves, the relation between them, the new operational quantities and the new quantities defined in the ICRP 60 that replaced ICRP 26 and was included in the CNEN-NN-3.01 standard of 2011

  5. Strongly intensive quantities

    International Nuclear Information System (INIS)

    Gorenstein, M. I.; Gazdzicki, M.

    2011-01-01

    Analysis of fluctuations of hadron production properties in collisions of relativistic particles profits from use of measurable intensive quantities which are independent of system size variations. The first family of such quantities was proposed in 1992; another is introduced in this paper. Furthermore we present a proof of independence of volume fluctuations for quantities from both families within the framework of the grand canonical ensemble. These quantities are referred to as strongly intensive ones. Influence of conservation laws and resonance decays is also discussed.

  6. Iodine-131 Releases from Radioactive Lanthanum Processing at the X-10 Site in Oak Ridge, Tennessee (1944-1956)- An Assessment of Quantities released, Off-Site Radiation Doses, and Potential Excess Risks of Thyroid Cancer- APPENDICES Appendices-Volume 1A

    International Nuclear Information System (INIS)

    Apostoaei, A.I.; Burns, R.E.; Hoffman, F.O.; Ijaz, T.; Lewis, C.J.; Nair, S.K.; Widner, T.E.

    1999-01-01

    This report consists of all the appendices for the report described below: In the early 1990s, concern about the Oak Ridge Reservation's past releases of contaminants to the environment prompted Tennessee's public health officials to pursue an in-depth study of potential off-site health effects at Oak Ridge. This study, the Oak Ridge dose reconstruction, was supported by an agreement between the U.S. Department of Energy (DOE) and the State of Tennessee, and was overseen by a 12-member panel appointed by Tennessee's Commissioner of Health. One of the major contaminants studied in the dose reconstruction was radioactive iodine, which was released to the air by X-10 (now called Oak Ridge National Laboratory) as it processed spent nuclear reactor fuel from 1944 through 1956. The process recovered radioactive lanthanum for use in weapons development. Iodine concentrates in the thyroid gland so health concerns include various diseases of the thyroid, such as thyroid cancer. The large report, ''Iodine-131 Releases from Radioactive Lanthanum Processing at the X-10 Site in Oak Ridge, Tennessee (1944-1956) - An Assessment of Quantities Released, Off-site Radiation Doses, and Potential Excess Risks of Thyroid Cancer,'' is in two volumes. Volume 1 is the main body of the report, and Volume 1A, which has the same title, consists of 22 supporting appendices. Together, these reports serve the following purposes: (1) describe the methodologies used to estimate the amount of iodine-131 (I-131) released; (2) evaluate I-131's pathway from air to vegetation to food to humans; (3) estimate doses received by human thyroids; (4) estimate excess risk of acquiring a thyroid cancer during ones lifetime; and (5) provide equations, examples of historical documents used, and tables of calculated values as appendices. Results indicate that females born in 1952 who consumed milk from a goat pastured a few miles east of X-10 received the highest doses from I-131 and would have had the highest

  7. Iodine-131 Releases from Radioactive Lanthanum Processing at the X-10 Site in Oak Ridge, Tennessee (1944-1956)- An Assessment of Quantities released, Off-Site Radiation Doses, and Potential Excess Risks of Thyroid Cancer- APPENDICES Appendices-Volume 1A

    Energy Technology Data Exchange (ETDEWEB)

    Apostoaei, A.I.; Burns, R.E.; Hoffman, F.O.; Ijaz, T.; Lewis, C.J.; Nair, S.K.; Widner, T.E.

    1999-07-01

    This report consists of all the appendices for the report described below: In the early 1990s, concern about the Oak Ridge Reservation's past releases of contaminants to the environment prompted Tennessee's public health officials to pursue an in-depth study of potential off-site health effects at Oak Ridge. This study, the Oak Ridge dose reconstruction, was supported by an agreement between the U.S. Department of Energy (DOE) and the State of Tennessee, and was overseen by a 12-member panel appointed by Tennessee's Commissioner of Health. One of the major contaminants studied in the dose reconstruction was radioactive iodine, which was released to the air by X-10 (now called Oak Ridge National Laboratory) as it processed spent nuclear reactor fuel from 1944 through 1956. The process recovered radioactive lanthanum for use in weapons development. Iodine concentrates in the thyroid gland so health concerns include various diseases of the thyroid, such as thyroid cancer. The large report, ''Iodine-131 Releases from Radioactive Lanthanum Processing at the X-10 Site in Oak Ridge, Tennessee (1944-1956) - An Assessment of Quantities Released, Off-site Radiation Doses, and Potential Excess Risks of Thyroid Cancer,'' is in two volumes. Volume 1 is the main body of the report, and Volume 1A, which has the same title, consists of 22 supporting appendices. Together, these reports serve the following purposes: (1) describe the methodologies used to estimate the amount of iodine-131 (I-131) released; (2) evaluate I-131's pathway from air to vegetation to food to humans; (3) estimate doses received by human thyroids; (4) estimate excess risk of acquiring a thyroid cancer during ones lifetime; and (5) provide equations, examples of historical documents used, and tables of calculated values as appendices. Results indicate that females born in 1952 who consumed milk from a goat pastured a few miles east of X-10 received the highest doses from

  8. Quantities for environmental monitoring

    International Nuclear Information System (INIS)

    1989-01-01

    It is recommended that if measurements are made with the objective of monitor radiation levels in the environment to elucidate long-term changes in these levels, then air kerma should be used. If the objective is to give an indication that levels from man-made sources are acceptable within specified limits for the exposure of people, then ambient dose equivalent should be used. It should be noted that radiation risks to individuals are best expressed by the quantity effective dose equivalent. If this latter quantity is to be accurately assessed, it may be necessary to obtain details of the quality of the environmental radiation that cannot be described adequately by simple measurements of either air kerma or ambient dose equivalent. If the above objectives pertain, the measurements should record both air kerma and ambient dose equivalent. If neutrons are measured in the environment then ambient dose equivalent is the appropriate quantity for both the above objectives. (author)

  9. Radiation quantities and units

    International Nuclear Information System (INIS)

    1980-01-01

    This report supersedes ICRU Report 19. Since ICRU Report 19 was published, a number of discussions have taken place between members of the Report Committee on Fundamental Quantities and Units and other workers in the field. Some of these discussions have resulted in the acceptance of certain modifications in the material set out in Report 19 and these modifications are incorporated in the current report. In addition, there has been some expansion and rearrangement of the material in the earlier report. In line, with providing more didactic material and useful source material for other ICRU reports, the general considerations in subsection 1.A of Report 19 have been expanded and placed in a separate subsection. The additional material includes discussions of four terms that are used in this document - quantity, unit, stochastic, and non-stochastic - along with a brief discussion of the mathematical formalism used in ICRU reports. As in ICRU Report 19, the definitions of quantities and units specifically designed for radiation protection (Part B) are separated from those of the general quantities (Part A). The inclusion of the index concept outlined in ICRU Report 25[4] required an extension of Part B

  10. DOE approach to threshold quantities

    International Nuclear Information System (INIS)

    Wickham, L.E.; Kluk, A.F.; Department of Energy, Washington, DC)

    1985-01-01

    The Department of Energy (DOE) is developing the concept of threshold quantities for use in determining which waste materials must be handled as radioactive waste and which may be disposed of as nonradioactive waste at its sites. Waste above this concentration level would be managed as radioactive or mixed waste (if hazardous chemicals are present); waste below this level would be handled as sanitary waste. Ideally, the threshold must be set high enough to significantly reduce the amount of waste requiring special handling. It must also be low enough so that waste at the threshold quantity poses a very small health risk and multiple exposures to such waste would still constitute a small health risk. It should also be practical to segregate waste above or below the threshold quantity using available instrumentation. Guidance is being prepared to aid DOE sites in establishing threshold quantity values based on pathways analysis using site-specific parameters (waste stream characteristics, maximum exposed individual, population considerations, and site specific parameters such as rainfall, etc.). A guidance dose of between 0.001 to 1.0 mSv/y (0.1 to 100 mrem/y) was recommended with 0.3 mSv/y (30 mrem/y) selected as the guidance dose upon which to base calculations. Several tasks were identified, beginning with the selection of a suitable pathway model for relating dose to the concentration of radioactivity in the waste. Threshold concentrations corresponding to the guidance dose were determined for waste disposal sites at a selected humid and arid site. Finally, cost-benefit considerations at the example sites were addressed. The results of the various tasks are summarized and the relationship of this effort with related developments at other agencies discussed

  11. Forage quantity and quality

    Science.gov (United States)

    Jorgenson, Janet C.; Udevitz, Mark S.; Felix, Nancy A.; Douglas, David C.; Reynolds, Patricia E.; Rhode, E.B.

    2002-01-01

    The Porcupine caribou herd has traditionally used the coastal plain of the Arctic National Wildlife Refuge, Alaska, for calving. Availability of nutritious forage has been hypothesized as one of the reasons the Porcupine caribou herd migrates hundreds of kilometers to reach the coastal plain for calving (Kuropat and Bryant 1980, Russell et al. 1993).Forage quantity and quality and the chronology of snowmelt (which determines availability and phenological stages of forage) have been suggested as important habitat attributes that lead calving caribou to select one area over another (Lent 1980, White and Trudell 1980, Eastland et al. 1989). A major question when considering the impact of petroleum development is whether potential displacement of the caribou from the 1002 Area to alternate calving habitat will limit access to high quantity and quality forage.Our study had the following objectives: 1) quantify snowmelt patterns by area; 2) quantify relationships among phenology, biomass, and nutrient content of principal forage species by vegetation type; and 3) determine if traditional concentrated calving areas differ from adjacent areas with lower calving densities in terms of vegetation characteristics.

  12. Prices versus Quantities

    DEFF Research Database (Denmark)

    Hansen, Lars Gårn; Jensen, Frank

    illustrate that this result does not generalise to a search fishery, where marginal costs are allowed to depend on harvest. Hansen et al (2008) study a fishery where non-compliance with regulations is a problem. When the regulator is uncertain about non-compliance (compliance uncertainty), then landing fees......Weitzman (2002) studies the regulation of a fishery characterised by constant marginal harvest costs and shows that price regulation performs better than quantity regulation when the regulator is uncertain about the biological reproduction function (ecological uncertainty). Here, we initially...... are the preferred type of regulation, and Hansen et al (2008) find that this result does generalise to a search fishery where marginal costs depend on harvest. In this paper, we simulate a stochastic stock-recruitment model for the Danish cod fishery in the Kategat capturing both ecological and compliance...

  13. Allen's astrophysical quantities

    CERN Document Server

    2000-01-01

    This new, fourth, edition of Allen's classic Astrophysical Quantities belongs on every astronomer's bookshelf. It has been thoroughly revised and brought up to date by a team of more than ninety internationally renowned astronomers and astrophysicists. While it follows the basic format of the original, this indispensable reference has grown to more than twice the size of the earlier editions to accommodate the great strides made in astronomy and astrophysics. It includes detailed tables of the most recent data on: - General constants and units - Atoms, molecules, and spectra - Observational astronomy at all wavelengths from radio to gamma-rays, and neutrinos - Planetary astronomy: Earth, planets and satellites, and solar system small bodies - The Sun, normal stars, and stars with special characteristics - Stellar populations - Cataclysmic and symbiotic variables, supernovae - Theoretical stellar evolution - Circumstellar and interstellar material - Star clusters, galaxies, quasars, and active galactic nuclei ...

  14. Relativity of Electric Quantity

    Directory of Open Access Journals (Sweden)

    GAO Zhong-wen

    2017-04-01

    Full Text Available The demonstration foundation,which is used to demonstrate that observed values from the interaction force between two charges,which are not at the same point would be different in different reference frames,is that the transmission of the interaction between charges needs time. Firstly,this paper analyzes the foundation of hypothetical process that the electric field and the magnetic field are built by one charge,and then the electromagnetic field would be transferred to another charge in vacuo by the speed of light,and produces force. It points out that from the simultaneity of relativity,the force applied to charge would occur in different time in the different reference frames,the force would be neither in the same size nor in the opposite direction,and Newton’s Third Law is not valid longer, the deeper cause of these conclusions would be known. On this basis,this paper gives the basis that force would keep invariant in different reference frames,and according to this condition,with the situation of the charge that under the Coulombian force and electromagnetism,the relative form of expression and demonstration methods of electric quantity in different reference frames are given. On the basis of the hypothesis that force would keep invariant in different reference frames,with the similar derivation process,the mass relativity equation of Einstein would be obtained.

  15. Fission-product release during accidents

    International Nuclear Information System (INIS)

    Hunt, C.E.L.; Cox, D.S.

    1991-09-01

    One of the aims when managing a reactor accident is to minimize the release of radioactive fission products. Release is dependent not only on the temperature, but also on the partial pressure of oxygen. Strongly oxidizing atmospheres, such as those that occurred during the Chernobyl accident, released semi-volatile elements like ruthenium, which has volatile oxides. At low temperatures, UO 2 oxidization to U 3 O 8 can result in extensive breakup of the fuel, resulting in the release of non-volatile fission products as aerosols. Under less oxidizing conditions, when hydrogen accumulates from the zirconium-water reaction, the resulting low oxygen partial pressure can significantly reduce these reactions. At TMI-2, only the noble gases and volatile fission products were released in significant quantities. A knowledge of the effect of atmosphere as well as temperature on the release of fission products from damaged reactor cores is therefore a useful, if not necessary, component of information required for accident management

  16. Significance of starch properties and quantity on sponge cake volume

    Science.gov (United States)

    We evaluated the qualitative and quantitative effects of wheat starch on sponge cake (SC) baking quality. Twenty wheat flours, including soft white and club wheat of normal, partial waxy and waxy endosperm, and hard wheat, were tested for amylose content, pasting properties, and SC baking quality. S...

  17. Significant adverse reactions to long-acting gonadotropin-releasing hormone agonists for the treatment of central precocious puberty and early onset puberty

    Directory of Open Access Journals (Sweden)

    Ji Woo Lee

    2014-09-01

    Full Text Available PurposeLong-acting gonadotropin-releasing hormone agonists (GnRHa are commonly used to treat central precocious puberty (CPP in Korea. Although rare, there have been reports on the characteristic of adverse reactions of GnRHa in CPP among the Korean population. This study was intended to report on our clinical experience regarding significant adverse reactions to long-acting GnRHa in CPP and early onset puberty and to evaluate the prevalence rate of serious side effects.MethodsThis retrospective study included children with CPP and early onset puberty, who were administered monthly with long-acting GnRHa (leuprolide acetate, triptorelin acetate at the outpatient clinic of Department of Pediatrics, at Inha University Hospital, between January 2011 and December 2013. We analyzed the clinical characteristics of patients who experienced significant adverse reactions and evaluated the prevalence rate.ResultsSix serious side effects (0.9% were observed among total of 621 CPP and early onset puberty children with GnRHa therapy. The number of sterile abscess formation was four in three patients (4 events of 621. Anaphylaxis occurred in only one patient, and unilateral slipped capital femoral epiphysis (SCFE in another one patient. Anaphylaxis occurred after the 6th administration of the monthly depot triptorelin acetate. Unilateral SCFE developed in GnRHa therapy.ConclusionSterile abscess formation occurred in 0.6% of CPP and early onset puberty patients from the administration of a monthly depot GnRHa therapy. The occurrences of anaphylaxis and SCFE are extremely rare, but can have serious implications on patients. Clinicians should be aware of these potential adverse effects related to GnRHa therapy in CPP.

  18. [The changes of ghrelin, growth hormone, growth hormone releasing hormone and their clinical significances in patients with chronic obstructive pulmonary disease].

    Science.gov (United States)

    Xu, Zhi-song; Bao, Zi-yu; Wang, Zhi-ying; Yang, Guo-jun; Zhu, Dong-fang; Zhang, Li; Tan, Rong-mei

    2012-07-01

    To investigate the changes of plasma ghrelin, growth hormone (GH) and growth hormone releasing hormone (GHRH) and gastric ghrelin in patients with chronic obstructive pulmonary disease (COPD) and to explore their clinical significances. Plasma ghrelin, GH, GHRH, TNFα, IL-6 and C reactive protein (CRP) were measured in 40 COPD patients and 20 controls with chronic bronchitis. Correlated factors of plasma ghrelin, TNFα, IL-6, CRP were analyzed. Body composition was assessed with bioelectrical impedance analysis. The expression of gastric ghrelin in patients with COPD was detected. Plasma ghrelin was higher in the underweight patients than in the normal weight patients and in the controls [(1.78 ± 0.46) ng/L, (1.39 ± 0.46) ng/L, (1.36 ± 0.39) ng/L, respectively]. Plasma GH was lower in the underweight patients than in the normal weight patients and in the controls [(4.12 ± 0.83) µg/L, (5.17 ± 0.72)µg/L, (6.49 ± 1.13) µg/L, respectively]. Plasma GHRH was lower in the underweight patients than in the normal weight patients and in the controls [(20.43 ± 4.41) ng/L, (23.47 ± 3.97) ng/L, (27.48 ± 10.06) ng/L, respectively]. Plasma ghrelin was higher in the underweight patients than in the controls (P 0.05). Plasma ghrelin was positively correlated with TNFα and IL-6 in the underweight patients. The gastric expression of ghrelin showed no evident difference between the patients with COPD and the controls. The plasma GH in COPD patients may not be correlated with ghrelin. The plasma ghrelin level may be a useful indicator for malnutrition in COPD patients. Plasma ghrelin might be involved in the pathogenesis of CODP by affecting the body energy metabolism.

  19. Relationships of chemical composition, quantity of milt to fertility and ...

    African Journals Online (AJOL)

    African Journal of Food, Agriculture, Nutrition and Development ... determining the right quantity of milt that can be used to fertilize certain quantity of eggs. ... quantity of milt used for artificial reproduction in fish significantly affect water quality used ... is the major organic substance that supplies the spermatozoa with energy.

  20. Quantity Stickiness versus Stackelberg Leadership

    International Nuclear Information System (INIS)

    Ferreira, F. A.

    2008-01-01

    We study the endogenous Stackelberg relations in a dynamic market. We analyze a twice-repeated duopoly where, in the beginning, each firm chooses either a quantity-sticky production mode or a quantity-flexible production mode. The size of the market becomes observable after the first period. In the second period, a firm can adjust its quantity if, and only if, it has adopted the flexible mode. Hence, if one firm chooses the sticky mode whilst the other chooses the flexible mode, then they respectively play the roles of a Stackelberg leader and a Stackelberg follower in the second marketing period. We compute the supply quantities at equilibrium and the corresponding expected profits of the firms. We also analyze the effect of the slope parameter of the demand curve on the expected supply quantities and on the profits.

  1. Thermal quantities of 46Ti

    International Nuclear Information System (INIS)

    Rahmatinejad, A.; Razavi, R.; Kakavand, T.

    2015-01-01

    Thermodynamic quantities of 46 Ti have been calculated in the framework of the BCS model with inclusion of modified nuclear pairing gap (MPBCS) that was proposed in our previous publication. Using modified paring gap results in an S-shaped heat capacity curve at critical temperature with a smooth behavior instead of singular behavior of the same curve in the BCS calculations. In addition the thermal quantities have been extracted within the framework of a canonical ensemble according to the new experimental data on nuclear level densities measured by the Oslo group. Comparison shows a good agreement between our calculations in MPBCS and the extracted quantities in the canonical ensemble framework

  2. Environmental significance of copper, lead, manganese, uranium and zinc speciation in the event of contaminated waters release from the Ranger Uranium Mining Complex

    International Nuclear Information System (INIS)

    Noller, B.N.; Currey, N.A.

    1983-01-01

    The likely impact of the accidental release of tailings dam water during the dry season at the Ranger Uranium Mining Complex was examined. A speciation scheme utilising sizing by filtration and ion-exchange with Chelex 100 has given an insight into the likely partitioning of zinc, copper, lead, manganese and uranium following the addition of tailings dam water to samples from waterbodies in the vicinity of the uranium mining/milling complex. The speciation findings are discussed in terms of likely toxic effects on fish

  3. The release of nickel and other trace elements from electric kettles and coffee machines

    DEFF Research Database (Denmark)

    Berg, T.; Petersen, Annette; Pedersen, Gitte Alsing

    2000-01-01

    was improved. Two of these ten kettles still released more than 50 mu g/l nickel to water under the test conditions. These two kettles, however, were subsequently withdrawn from the market. Coffee machines tested similarly did not release aluminium, lead, chromium or nickel in quantities of any significance....

  4. Quantity Estimation Of The Interactions

    International Nuclear Information System (INIS)

    Gorana, Agim; Malkaj, Partizan; Muda, Valbona

    2007-01-01

    In this paper we present some considerations about quantity estimations, regarding the range of interaction and the conservations laws in various types of interactions. Our estimations are done under classical and quantum point of view and have to do with the interaction's carriers, the radius, the influence range and the intensity of interactions

  5. Recognizing Prefixes in Scientific Quantities

    Science.gov (United States)

    Sokolowski, Andrzej

    2015-01-01

    Although recognizing prefixes in physical quantities is inherent for practitioners, it might not be inherent for students, who do not use prefixes in their everyday life experiences. This deficiency surfaces in AP Physics exams. For example, readers of an AP Physics exam reported "a common mistake of incorrectly converting nanometers to…

  6. Definitions of Quantities and Units.

    Science.gov (United States)

    Spurgin, C. B.

    1983-01-01

    Compares various methods of defining derived quantities, arguing for a definitional formula using base or fundamental units in a word equation, or symbol-equations with the symbols explained. Suggests that fundamental units be defined operationally or left regarded as intuitive as in the case of length and time. (JM)

  7. A Case of Acromegaly in which a Pituitary Gland Tumor was Reduced Significantly by Administering Octreotide Long Acting Release (LAR) and Could Be Removed Surgically.

    Science.gov (United States)

    Arao, Tadashi; Okada, Yosuke; Uemura, Fumi; Nishizawa, Shigeru; Tanaka, Yoshiya

    A 54-year-old woman was admitted to our hospital for detailed examination of acromegaly because she noticed bilateral hand and finger swelling at the age of 43 and plantar thickening, facial changes and unclear articulation at the age of 49. She had prominent brow ridges, mandibular protrusion, and enlargement of the hands, feet, nasal wings, lips and tongue. Her growth hormone (GH) level was 39.8 ng/ml, insulin-like growth factor-1 (IGF-1) level was 717 ng/ml, GH level was not suppressed (22.9 ng/ml) during a 75-g oral glucose tolerance test (OGTT). Radiography showed cauliflower-like enlargement of the distal phalanx of the fingers, thickening/enlargement of the plantar soft tissues, and increased antero-posterior diameter of the sella turcica. Magnetic resonance imaging showed a mass (21×17 mm) growing towards the right suprasellar region and invading the cavernous sinus. She was diagnosed with acromegaly based on the characteristic physical findings, GH excess, high IGF-1, lack of GH suppression during the 75-g OGTT, and the presence of a pituitary tumor. She was started on octreotide long acting release (Oct-LAR) 20 mg/4w for tumor shrinkage. After three doses, her GH and IGF-1 levels decreased to 2.19 ng/ml (1.69 during the 75-g OGTT) and 205 ng/ml, respectively, meeting cure criteria for acromegaly. In this case, a decrease in GH and IGF-1 levels, tumor shrinkage, and resolution of cavernous sinus invasion allowed the patient to undergo surgery with curative intent (the first-line treatment for acromegaly) without postoperative complications. Thus, preoperative Oct-LAR administration has the potential to improve treatment outcomes of acromegaly.

  8. Strategic Planning in Irish Quantity Surveying Pracitces

    OpenAIRE

    Murphy, Roisin

    2011-01-01

    The role and usefulness of strategic planning has been well documented over several decades of strategic management research. Despite the significant body of existing knowledge in the field of strategic planning, there remains a paucity of investigation into the construction sector, specifically in Professional Service Firms (PSF’s) operating within it. The aim of this research was to ascertain the type, scope and extent of strategic planning within Irish Quantity Surveying (QS) practices and...

  9. Quantities used in radiological protection

    International Nuclear Information System (INIS)

    Menossi, Carlos

    2010-01-01

    The application of ICRP recommendations requires knowledge of a variety of concepts and magnitudes. Many of them are employed in other fields of science and precision in its definition reflects this wide application. In this regard, information on quantities and basic units of radiation, which exists in numerous publications, are subjects of great interest. The characteristics and radiation effects are studied by physicists, biologists and chemists mainly. However, there are basics that must be known and to be recognized by general practitioners and specialists from all branches of medicine. The information on quantities and units are used only in radiation protection, have been obtained from the reports listed on the attached bibliography. Such quantities and units contain weighting factors used to provide for different types of radiation and energies that affect the body and thus take into account the relative radio-sensitivity of different tissues. Additionally, they have added a series of data for a better understanding of the units: for example, multiples and sub-multiples, and some examples of converting the units used in radiation protection. (author) [es

  10. Variation in Quantity of Heat Produced from Charcoal of Prosopis ...

    African Journals Online (AJOL)

    Data were collected using the copper calorimeter, a thermometer, an air tight burner and a weight balance. The results showed a gradual decrease in the quantity of heat produced as combustion time increased from 10 40 minutes in all wood species. Significant differences (p<0.05) in the quantity of heat produced both ...

  11. How necessary are the new quantities

    International Nuclear Information System (INIS)

    Kraus, W.

    1991-01-01

    The necessity of the ICRU operational quantities is discussed from the point of view of practical, opertional radiation protection, on the basis of ICRU report 43. It is clear that, although the new quantities have some advantages over previous systems of operational quantities, there are some disadvantages as well. The decision to adopt these quantities is, therefore, not clear cut. (orig.)

  12. Are necessary unmeasurable quantities in radiation protection?

    International Nuclear Information System (INIS)

    David, M.G.; Correa, M.F.; Videira, A.A.P.

    2016-01-01

    We discuss in this paper the metrological status of unmeasurable protection quantities and the need to maintain these kind of quantities in the system. The discussion is based on reports from the institutions responsible for the quantities and on scientific publications. In conclusion, we can say that there are alternatives for changing the system in a way that it keep just measurable quantities, nevertheless the present system is well assimilated. Even though a proposal yet to be presented for changing the system, although might simplify and improve it, is not intended to overcome the existence of unmeasurable quantities or the two kinds of quantities. (author)

  13. Memory-Based Quantity Discrimination in Coyotes (Canis latrans

    Directory of Open Access Journals (Sweden)

    Salif Mahamane

    2014-08-01

    Full Text Available Previous research has shown that the ratio between competing quantities of food significantly mediates coyotes‘ (Canis latrans ability to choose the larger of two food options. These previous findings are consistent with predictions made by Weber‘s Law and indicate that coyotes possess quantity discrimination abilities that are similar to other species. Importantly, coyotes‘ discrimination abilities are similar to domestic dogs (Canis lupus familiaris, indicating that quantitative discrimination may remain stable throughout certain species‘ evolution. However, while previously shown in two domestic dogs, it is unknown whether coyotes possess the ability to discriminate visual quantities from memory. Here, we address this question by displaying different ratios of food quantities to 14 coyotes before placing the choices out of sight. The coyotes were then allowed to select one of either non-visible food quantities. Coyotes‘ discrimination of quantity from memory does not follow Weber‘s Law in this particular task. These results suggest that working memory in coyotes may not be adapted to maintain information regarding quantity as well as in domestic dogs. The likelihood of a coyote‘s choosing the large option increased when it was presented with difficult ratios of food options first, before it was later presented with trials using more easily discriminable ratios, and when the large option was placed on one particular side. This suggests that learning or motivation increased across trials when coyotes experienced difficult ratios first, and that location of food may have been more salient in working memory than quantity of food.

  14. Asymptotic conditions and conserved quantities

    International Nuclear Information System (INIS)

    Koul, R.K.

    1990-01-01

    Two problems have been investigated in this dissertation. The first one deals with the relationship between stationary space-times which are flat at null infinity and stationary space-times which are asymptotic flat at space-like infinity. It is shown that the stationary space-times which are asymptotically flat, in the Penrose sense, at null infinity, are asymptotically flat at space-like infinity in the Geroch sense and metric at space like infinity is at least C 1 . In the converse it is shown that the stationary space-times which are asymptotically flat at space like infinity, in the Beig sense, are asymptotically flat at null infinity in the Penrose sense. The second problem addressed deals with the theories of arbitrary dimensions. The theories treated are the ones which have fiber bundle structure, outside some compact region. For these theories the criterion for the choice of the background metric is specified, and the boundary condition for the initial data set (q ab , P ab ) is given in terms of the background metric. Having these boundary conditions it is shown that the symplectic structure and the constraint functionals are well defined. The conserved quantities associated with internal Killing vector fields are specified. Lastly the energy relative to a fixed background and the total energy of the theory have been given. It is also shown that the total energy of the theory is independent of the choice of the background

  15. Impact of the Velo 2 half misalignment on physical quantities

    CERN Document Server

    Roguljic, Matej; Borghi, Silvia; Grillo, Lucia; CERN. Geneva. EP Department

    2016-01-01

    The impact of the misalignment of the Vertex Locator of the LHCb experiment on the physical quantities of the decay "$D^{*+} \\rightarrow (D^{0}\\rightarrow K^{-}\\pi^{+}) \\pi^{+} $" is studied in this note. Different misalignments of the 2 halves are applied to Monte Carlo data and the variations of the physical quantities with respect to the case without misalignment are evaluated. The results show the importance of the VELO 2 half alignment which can significantly affect the physics performance in the large misalignment case. A misalignment equal to the precision of the real-time alignment of the Vertex Locator is found to have a negligible effect on the studied physical quantities.

  16. Serum-free culture alters the quantity and protein composition of neuroblastoma-derived extracellular vesicles

    Directory of Open Access Journals (Sweden)

    Jinghuan Li

    2015-05-01

    Full Text Available Extracellular vesicles (EVs play a significant role in cell–cell communication in numerous physiological processes and pathological conditions, and offer promise as novel biomarkers and therapeutic agents for genetic diseases. Many recent studies have described different molecular mechanisms that contribute to EV biogenesis and release from cells. However, little is known about how external stimuli such as cell culture conditions can affect the quantity and content of EVs. While N2a neuroblastoma cells cultured in serum-free (OptiMEM conditions did not result in EVs with significant biophysical or size differences compared with cells cultured in serum-containing (pre-spun conditions, the quantity of isolated EVs was greatly increased. Moreover, the expression levels of certain vesicular proteins (e.g. small GTPases, G-protein complexes, mRNA processing proteins and splicing factors, some of which were previously reported to be involved in EV biogenesis, were found to be differentially expressed in EVs under different culture conditions. These data, therefore, contribute to the understanding of how extracellular factors and intracellular molecular pathways affect the composition and release of EVs.

  17. Dose rate constants for new dose quantities

    International Nuclear Information System (INIS)

    Tschurlovits, M.; Daverda, G.; Leitner, A.

    1992-01-01

    Conceptual changes and new quantities made is necessary to reassess dose rate quantities. Calculations of the dose rate constant were done for air kerma, ambient dose equivalent and directional dose equivalent. The number of radionuclides is more than 200. The threshold energy is selected as 20 keV for the dose equivalent constants. The dose rate constant for the photon equivalent dose as used mainly in German speaking countries as a temporary quantity is also included. (Author)

  18. The new operational quantities for radiation protection

    International Nuclear Information System (INIS)

    Kellerer, A.M.

    1985-01-01

    Philosophies and quantities for radiation protection have often been subjected to changes, and some of the developments are traced which ultimately led to recent proposals by ICRU. Development in the past has largely been towards clarification and generalisation of definitions. The present changes, however, reflect a more fundamental issue, the transition from the limitation system to the assessment system in radiation protection. The index quantities were suitable tools to ascertain compliance with the limitation system of radiation protection. The new quantities proposed by ICRU are suitable estimators for effective dose equivalent, which is an essential quantity in the assessment system of radiation protection. A synopsis of the definitions is given. (author)

  19. Foreign materials in the repository - update of estimated quantities

    International Nuclear Information System (INIS)

    Hagros, A.

    2007-03-01

    In a repository for spent nuclear fuel, a variety of materials are used during the construction process and during the operation of the repository. In addition to materials necessary for the construction and operation, some materials may be transported into the repository through the ventilation air, as emissions from vehicles, as waste produced by the staff etc. Both of these two types of materials are considered here and their quantities - both the introduced quantities and the quantities that remain after closure - in the repository constructed at Olkiluoto in Eurajoki, Finland are estimated here based on new information. This work is intended to update the estimations that have been made previously, and it takes advantage of the experience collected during the construction of the underground rock characterisation facility ONKALO at Olkiluoto. During this construction process, the quantities of the different construction materials introduced into the underground openings have been monitored and they form a basis for estimating the quantities to be used in the future. The estimations made in this report are specific to a KBS-3V type repository and to the Olkiluoto site, although in some cases more generic information has been used, particularly when the relevant quantities have not been monitored in the ONKALO. The estimations are based on the new repository layout produced in 2006 and consider the latest plans for grouting and rock support. As these plans are generally not final yet, several different alternative plans are assumed when necessary. Also two different strategies for the backfilling of the tunnels are considered. The most significant differences with respect to the results of an earlier estimation are related to the materials used in grouting, shotcreting and in support bolts. In the cases where a mixture of bentonite and crushed rock is the used backfill alternative, gypsum and cement are the materials with the largest quantities remaining in the

  20. Food quantity affects the sensitivity of Daphnia to road salt.

    Science.gov (United States)

    Brown, Arran H; Yan, Norman D

    2015-04-07

    Road deicing operations have raised chloride (Cl) levels in many temperate lakes in Europe and North America. These lakes vary widely in trophic status, but to date, no one has quantified the interaction between food quantity and road salt toxicity. We examined the effects of food quantity (particulate algal C concentration (C)) on the chronic toxicity of Cl to Daphnia in soft-water bioassays. There was a strong positive linear relationship (r(2) = 0.92 for NaCl and r(2) = 0.96 for CaCl2) between food quantity and Cl LC50. As food quantity increased from 0.2 to 1.0 mg C/L (levels characteristic of oligotrophic to eutrophic lakes, respectively), the chronic Cl LC50 increased from 55.7 to 284.8 mg Cl/L. Salt type (NaCl or CaCl2) did not affect the Cl LC50, Daphnia life history parameters, or the intrinsic rate of population increase (r). The life history parameter most sensitive to Cl was neonate production. Cl did not inhibit egg production, nor was the maternal lipid investment in eggs changed, but egg viability and the subsequent release of live neonates decreased as Cl levels increased and food decreased. Our results suggest the trophic status of lakes should be considered when assessing ecological threat from Cl.

  1. Dosimetric radiation protection quantities. Impact of the forthcoming ICRP recommendations

    International Nuclear Information System (INIS)

    Pradhan, A.S.; Lee, J.I.; Kim, J.L.; Kim, B.H.

    2008-01-01

    The physical quantities namely fluence, kerma and absorbed dose provide the base for the operational and the protection quantities. The absorbed dose continues to be the fundamental physical quantity for the radiological protection. The most striking feature relating the quantities in the forthcoming recommendations is the updating of the radiation and tissue weighting factors based on the latest available scientific information on radiobiology and the physics of radiation exposure. This is bound to make a significant impact in arriving at the equivalent doses and effective dose. For external exposures of neutrons, the forthcoming recommendations are going to improve the relationship between the operational and protection quantities. The changes in the tissue weighting factors of some tissues/organs, the inclusion of several new tissues/organs for the consideration of tissue weighting factors and the use of the proposed Reference Male and Reference Female voxel phantoms would require new conversion coefficients and dose coefficients for external and internal exposures. The other striking feature appears to be the details of the concepts to ensure that the protections quantities are used for the appropriate and intended purposes only and the misuse is avoided. (author)

  2. Continuing Professional Development in the quantity surveying ...

    African Journals Online (AJOL)

    This research study was conducted in order to investigate Continuing Professional Development (CPD) in the South African quantity surveying profession. The study further aimed to establish the reasons why some quantity surveyors do not acquire the required CPD hours and face losing their professional registration with ...

  3. Continuing Professional Development in the quantity surveying ...

    African Journals Online (AJOL)

    1991-01-01

    Jan 1, 1991 ... The research established that quantity surveyors regarded handing in their CPD ... Surveying, Walter Sisulu University, PO Box 1421, East London, 5200, South Africa. ... Keywords: Continuing professional development, quantity surveying, perception .... In spite of this opportunity enshrined in the Act, the.

  4. 36 CFR 223.220 - Quantity determination.

    Science.gov (United States)

    2010-07-01

    ... 36 Parks, Forests, and Public Property 2 2010-07-01 2010-07-01 false Quantity determination. 223.220 Section 223.220 Parks, Forests, and Public Property FOREST SERVICE, DEPARTMENT OF AGRICULTURE SALE AND DISPOSAL OF NATIONAL FOREST SYSTEM TIMBER Special Forest Products § 223.220 Quantity determination...

  5. 30 CFR 75.325 - Air quantity.

    Science.gov (United States)

    2010-07-01

    ... the exposure of miners. (i) A ventilating air quantity that is less than what is required by paragraph... results of sampling that demonstrate that the lesser air quantity will maintain continuous compliance with applicable TLV ®'s. (j) If during sampling required by § 70.1900(c) of this subchapter the ventilating air is...

  6. Method and means for determining heat quantities

    Energy Technology Data Exchange (ETDEWEB)

    Waasdorp, G G; de Jong, J J; Bijl, A

    1965-08-24

    To determine the quantity of potential heat W that has flowed past a certain point in a certain time, the velocity of the combustible Q, the temperature T, and the specific gravity YDTU are measured, and these values are transmitted to a computer which automatically calculates the quantity: ..pi..EQUATION/sup -/ in which delta T is the difference between the combustible temperature T and a reference temperature, and in which the relation f(YDTU, delta T) represents the heat of combustion as a function of the quantities YDTU and delta T and possibly other properties of the combustible. Alternatively the quantity: ..pi..EQUATION/sup -/ may be measured; here the quantities have the same meaning as above.

  7. A Viewpoint on the Quantity "Plane Angle"

    Science.gov (United States)

    Eder, W. E.

    1982-01-01

    Properties of the quantity "plane angle" are explored under the hypothesis that it is a dimensional quantity. The exploration proceeds especially with respect to the physical concept, its mathematical treatment, vector concepts, measurement theory, units of related quantities, engineering pragmatism, and SI. An attempt is made to bring these different relations into a rational, logical and consistent framework, and thus to justify the hypothesis. Various types of vectorial quantities are recognized, and their properties described with an outline of the necessary algebraic manipulations. The concept of plane angle is amplified, and its interdependence with the circular arc is explored. The resulting units of plane angle form a class of similar scales of measurement. Consequences of the confirmed hypothesis are developed for mathematical expressions involving trigonometric functions, rotational volumes and areas, mathematical limits, differentiation and series expansion. Consequences for mechanical rotational quantities are developed, with proposals for revisions to a number of expressions for derived units within SI. A revised definition for the quantity "plane angle" is stated to take account of the developed insights. There is a clear need to reconsider the status of plane angle and some other quantities within the international framework of SI.

  8. Workplace stress experienced by quantity surveyors

    African Journals Online (AJOL)

    Paul (P.A.) Bowen, Department of Construction Economics and Management,. University of Cape Town, Private ..... Explore workplace stress levels among quantity surveyors in the developing nation of ...... London: Free. Association Books.

  9. The Radiometric Measurement Quantity for SAR Images

    OpenAIRE

    Döring, Björn J.; Schwerdt, Marco

    2013-01-01

    A Synthetic Aperture Radar (SAR) system measures among other quantities the terrain radar reflectivity. After image calibration, the pixel intensities are commonly expressed in terms of radar cross sections (for point targets) or as backscatter coefficients (for distributed targets), which are directly related. This paper argues that pixel intensities are not generally proportional to radar cross section or derived physical quantities. The paper further proposes to replace the inaccurate term...

  10. Average Transverse Momentum Quantities Approaching the Lightfront

    OpenAIRE

    Boer, Daniel

    2015-01-01

    In this contribution to Light Cone 2014, three average transverse momentum quantities are discussed: the Sivers shift, the dijet imbalance, and the $p_T$ broadening. The definitions of these quantities involve integrals over all transverse momenta that are overly sensitive to the region of large transverse momenta, which conveys little information about the transverse momentum distributions of quarks and gluons inside hadrons. TMD factorization naturally suggests alternative definitions of su...

  11. A conserved quantity in thin body dynamics

    Science.gov (United States)

    Hanna, J. A.; Pendar, H.

    2016-02-01

    Thin, solid bodies with metric symmetries admit a restricted form of reparameterization invariance. Their dynamical equilibria include motions with both rigid and flowing aspects. On such configurations, a quantity is conserved along the intrinsic coordinate corresponding to the symmetry. As an example of its utility, this conserved quantity is combined with linear and angular momentum currents to construct solutions for the equilibria of a rotating, flowing string, for which it is akin to Bernoulli's constant.

  12. Trained Quantity Abilities in Horses (Equus caballus: A Preliminary Investigation

    Directory of Open Access Journals (Sweden)

    Maria Elena Miletto Petrazzini

    2014-07-01

    Full Text Available Once believed to be a human prerogative, the capacity to discriminate between quantities now has also been reported in several vertebrates. To date, only two studies investigated numerical abilities in horses (Equus caballus but reported contrasting data. To assess whether horses can be trained to discriminate between quantities, I have set up a new experimental protocol using operant conditioning. One adult female was trained to discriminate between 1 and 4 (Test 1 in three different conditions: non-controlled continuous variables (numerical and continuous quantities that co-vary with number are simultaneously available, 50% controlled continuous variables (intermediate condition, and 100% controlled continuous variables (only numerical information available. The subject learned the discrimination in all conditions, showing the capacity to process numerical information. When presented with a higher numerical ratio (2 vs. 4, Test 2, the subject still discriminated between the quantities but its performance was statistically significant only in the non-controlled condition, suggesting that the subject used multiple cues in presence of a more difficult discrimination. On the whole, the results here reported encourage the use of this experimental protocol as a valid tool to investigate the capacity to process numerical and continuous quantities in horses in future research.

  13. Critical review of the current radiation protection quantities and units

    International Nuclear Information System (INIS)

    Sabol, J.

    1998-01-01

    Examples exist in dosimetry and radiation protection where primary attention was focused on the unit rather than the corresponding quantity. Another difficulty arises from the fact that quantities in this field cannot be considered as pure physical quantities, they are rather biophysical quantities. There are too many quantities (e. g. 17 quantities based on the dose equivalent), with differences in numerical values of 'similar' quantities, not always satisfactory approximations of virtually unmeasurable quantities by measurable quantities, inconsistency in definitions and interpretations of quantities of some international expert bodies, and problems of weighting and conversion factors. (M.D.)

  14. Foreign materials in the repository. Update of estimated quantities

    International Nuclear Information System (INIS)

    Karvonen, T.

    2011-06-01

    A variety of materials are used during the construction process and the operation of the repository for spent nuclear fuel at Olkiluoto in Eurajoki, Finland. In addition to materials necessary for the construction and operation, some materials may be transported into the repository with the ventilation air, as emissions from vehicles etc. Both of these two types of materials are considered here and both introduced quantities and the quantities that remain after the closure in the repository are estimated here based on the most recent information. This work is intended to update the previous estimations, and it takes advantage of the experience collected during the construction of the underground rock characterisation facility called ONKALO at Olkiluoto. The implemented quantities as well as designs and preliminary designs have been used in calculating the quantities of the foreign materials. The estimations made in this report are specific to a KBS-3V type repository. In some cases more generic information has been used, particularly when the relevant quantities have not been monitored in ONKALO. The estimations are based on the new repository layout produced in 2010 and consider the latest plans for grouting and rock support. As all of these plans are not final some quantities may change in the future. As the repository layout may still go through some changes this report also provides the foreign materials for a hundred meters of different deposition tunnels designed for the OL and LO type canisters1. The results have also been calculated for a space demanded by a deposition tunnel end plug and the tunnel lengths before and after one. The most significant foreign materials are certain accessory minerals of the clay materials followed by organic materials (including the organic carbon from the clay materials), cement, steel and silica. (orig.)

  15. A shared system of representation governing quantity discrimination in canids

    Directory of Open Access Journals (Sweden)

    Joseph M Baker

    2012-10-01

    Full Text Available One way to investigate the evolution of cognition is to compare the abilities of phylogenetically related species. The domestic dog (Canis lupus familiaris, for example, still shares cognitive abilities with the coyote (C. latrans. Both of these canids possess the ability to make psychophysical less/more discriminations of food based on quantity. Like many other species including humans, this ability is mediated by Weber’s Law: discrimination of continuous quantities is dependent on the ratio between the two quantities. As two simultaneously presented quantities of food become more similar, choice of the large or small option becomes random in both dogs and coyotes. It remains unknown, however, whether these closely related species within the same family—one domesticated, and one wild—make such quantitative comparisons with comparable accuracy. Has domestication honed or diminished this quantitative ability? Might different selective and ecological pressures facing coyotes drive them to be more or less able to accurately represent and discriminate food quantity than domesticated dogs? This study is an effort to elucidate this question concerning the evolution of non-verbal quantitative cognition.Here, we tested the quantitative discrimination ability of 16 domesticated dogs. Each animal was given 9 trials in which two different quantities of food were simultaneously displayed to them. The domesticated dogs’ performance on this task was then compared directly to the data from 16 coyotes’ performance on this same task reported by Baker and colleagues (2011.The quantitative discrimination abilities between the two species were strikingly similar. Domesticated dogs demonstrated similar quantitative sensitivity as coyotes, suggesting that domestication may not have significantly altered the psychophysical discrimination abilities of canids. Instead, this study provides further evidence for similar nonverbal quantitative abilities across

  16. Management of small quantities of radioactive waste

    International Nuclear Information System (INIS)

    1998-09-01

    The main objective of this publication is to provide practical guidance primarily to developing Member States on the predisposal management of small quantities of radioactive waste arising from hospitals, laboratories, industries, institutions, research reactors and research centres.The publication covers the management of liquid, solid and gaseous radioactive wastes at the users' premises and gives general guidance on procedures at a centralized waste management facility. Predisposal management of radioactive waste includes handling, treatment, conditioning, storage and transportation. This publication provides information and guidance on the following topics: national waste management framework; origin and characteristics of radioactive waste arising from users generating small quantities of waste; radioactive waste management concepts appropriate for small quantities; local waste management; the documentation and approval necessary for the consignment of waste to a centralized waste management facility; centralized waste management; exemption of radionuclides from the regulatory body; transportation; environmental monitoring; quality assurance for the whole predisposal process; regional co-operation aspects

  17. A conserved quantity in thin body dynamics

    International Nuclear Information System (INIS)

    Hanna, J.A.; Pendar, H.

    2016-01-01

    Thin, solid bodies with metric symmetries admit a restricted form of reparameterization invariance. Their dynamical equilibria include motions with both rigid and flowing aspects. On such configurations, a quantity is conserved along the intrinsic coordinate corresponding to the symmetry. As an example of its utility, this conserved quantity is combined with linear and angular momentum currents to construct solutions for the equilibria of a rotating, flowing string, for which it is akin to Bernoulli's constant. - Highlights: • A conserved quantity relevant to the dynamical equilibria of thin structures. • A mixed Lagrangian–Eulerian non-material action principle for fixed windows of axially moving systems. • Analytical solutions for rotating, flowing strings (yarn balloons). • Noether meets Bernoulli in a textile factory.

  18. A conserved quantity in thin body dynamics

    Energy Technology Data Exchange (ETDEWEB)

    Hanna, J.A., E-mail: hannaj@vt.edu [Department of Biomedical Engineering and Mechanics, Virginia Polytechnic Institute and State University, Blacksburg, VA 24061 (United States); Department of Physics, Virginia Polytechnic Institute and State University, Blacksburg, VA 24061 (United States); Pendar, H. [Department of Biomedical Engineering and Mechanics, Virginia Polytechnic Institute and State University, Blacksburg, VA 24061 (United States)

    2016-02-15

    Thin, solid bodies with metric symmetries admit a restricted form of reparameterization invariance. Their dynamical equilibria include motions with both rigid and flowing aspects. On such configurations, a quantity is conserved along the intrinsic coordinate corresponding to the symmetry. As an example of its utility, this conserved quantity is combined with linear and angular momentum currents to construct solutions for the equilibria of a rotating, flowing string, for which it is akin to Bernoulli's constant. - Highlights: • A conserved quantity relevant to the dynamical equilibria of thin structures. • A mixed Lagrangian–Eulerian non-material action principle for fixed windows of axially moving systems. • Analytical solutions for rotating, flowing strings (yarn balloons). • Noether meets Bernoulli in a textile factory.

  19. Relevance of protection quantities in medical exposures

    International Nuclear Information System (INIS)

    Pradhan, A.S.

    2008-01-01

    International Commission on Radiological Protection (ICRP) continues to classify the exposures to radiation in three categories; namely 1- occupational exposure, 2- public exposure, and 3- medical exposure. Protection quantities are primarily meant for the regulatory purpose in radiological protection for controlling and limiting stochastic risks in occupational and public exposures. These are based on two basic assumptions of 1- linear no-threshold dose-effect relationship (LNT) at low doses and 2- long-term additivity of low doses. Medical exposure are predominantly delivered to individuals (patients) undergoing diagnostic examinations, interventional procedures and radiation therapy but also include individual caring for or comforting patients incurring exposure and the volunteers of biomedical medical research programmes. Radiation protection is as relevant to occupational and public exposure as to medical exposures except that the dose limits set for the formers are not applicable to medical exposure but reference levels and dose constrains are recommended for diagnostic and interventional medical procedures. In medical institutions, both the occupational and medical exposure takes place. Since the doses in diagnostic examinations are low, it has been observed that not only the protection quantities are often used in such cases but these are extended to estimate the number of cancer deaths due to such practices. One of the striking features of the new ICRP recommendations has been to elaborate the concepts of the dosimetric quantities. The limitation of protection quantities ((Effective dose, E=Σ RT D TR .W T .W R and Equivalent Dose H T =Σ RT D TR .W R ) have been brought out and this has raised a great concern and initiated debates on the use of these quantities in medical exposures. Consequently, ICRP has set a task group to provide more details and the recommendations. It has, therefore, became important to draw the attention of medical physics community

  20. Editorial: New operational dose equivalent quantities

    International Nuclear Information System (INIS)

    Harvey, J.R.

    1985-01-01

    The ICRU Report 39 entitled ''Determination of Dose Equivalents Resulting from External Radiation Sources'' is briefly discussed. Four new operational dose equivalent quantities have been recommended in ICRU 39. The 'ambient dose equivalent' and the 'directional dose equivalent' are applicable to environmental monitoring and the 'individual dose equivalent, penetrating' and the 'individual dose equivalent, superficial' are applicable to individual monitoring. The quantities should meet the needs of day-to-day operational practice, while being acceptable to those concerned with metrological precision, and at the same time be used to give effective control consistent with current perceptions of the risks associated with exposure to ionizing radiations. (U.K.)

  1. Calibration of personal dosimeters: Quantities and terminology

    International Nuclear Information System (INIS)

    Aleinikov, V.E.

    1999-01-01

    The numerical results obtained in the interpretation of individual monitoring of external radiation depend not only on the accurate calibration of the radiation measurement instruments involved, but also on the definition of the quantities in term of which these instruments are calibrated The absence of uniformity in terminology not only makes it difficult to understand properly the scientific and technical literature but can also lead to incorrect interpretation of particular concepts and recommendations. In this paper, brief consideration is given to definition of radiation quantities and terminology used in calibration procedures. (author)

  2. On the Output-Inflation Relationship When Price and Quantity Adjustments are Costly

    DEFF Research Database (Denmark)

    Danziger, Leif; Kreiner, Claus Thustrup

    A vast literature analyzes the real effects of price-adjustment costs assuming that quantity adjustments are costless. In this paper, we analyze whether the presence of quantity-adjustments costs, which presumably are significant, change the traditional results on the impact of inflation....... In particular, recent findings suggest that quantity-adjustment costs may remove the linkage between output and inflation. We show that this is not the case when inflation is anticipated. On the contrary, quantity-adjustment costs may significantly amplify the consequences of price-adjustment costs...

  3. [Relativity among starch quantity, polysaccharides content and total alkaloid content of Dendrobium loddigesii].

    Science.gov (United States)

    Zhu, Hua; Teng, Jianbei; Cai, Yi; Liang, Jie; Zhu, Yilin; Wei, Tao

    2011-12-01

    To find out the relativity among starch quantity, polysaccharides content and total alkaloid content of Dendrobium loddigesii. Microscopy-counting process was applied to starch quantity statistics, sulfuric acid-anthrone colorimetry was used to assay polysaccharides content and bromocresol green colorimetry was used to assay alkaloid content. Pearson product moment correlation analysis, Kendall's rank correlation analysis and Spearman's concordance coefficient analysis were applied to study their relativity. Extremely significant positive correlation was found between starch quantity and polysaccharides content, and significant negative correlation between alkaloid content and starch quantity was discovered, as well was between alkaloid content and polysaccharides content.

  4. 7 CFR 35.13 - Minimum quantity.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 2 2010-01-01 2010-01-01 false Minimum quantity. 35.13 Section 35.13 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing... part, transport or receive for transportation to any foreign destination, a shipment of 25 packages or...

  5. Varieties of Quantity Estimation in Children

    Science.gov (United States)

    Sella, Francesco; Berteletti, Ilaria; Lucangeli, Daniela; Zorzi, Marco

    2015-01-01

    In the number-to-position task, with increasing age and numerical expertise, children's pattern of estimates shifts from a biased (nonlinear) to a formal (linear) mapping. This widely replicated finding concerns symbolic numbers, whereas less is known about other types of quantity estimation. In Experiment 1, Preschool, Grade 1, and Grade 3…

  6. Symmetries and conserved quantities in geodesic motion

    International Nuclear Information System (INIS)

    Hojman, S.; Nunez, L.; Patino, A.; Rago, H.

    1986-01-01

    Recently obtained results linking several constants of motion to one (non-Noetherian) symmetry to the problem of geodesic motion in Riemannian space-times are applied. The construction of conserved quantities in geodesic motion as well as the deduction of geometrical statements about Riemannian space-times are achieved

  7. Hypergraph topological quantities for tagged social networks

    Science.gov (United States)

    Zlatić, Vinko; Ghoshal, Gourab; Caldarelli, Guido

    2009-09-01

    Recent years have witnessed the emergence of a new class of social networks, which require us to move beyond previously employed representations of complex graph structures. A notable example is that of the folksonomy, an online process where users collaboratively employ tags to resources to impart structure to an otherwise undifferentiated database. In a recent paper, we proposed a mathematical model that represents these structures as tripartite hypergraphs and defined basic topological quantities of interest. In this paper, we extend our model by defining additional quantities such as edge distributions, vertex similarity and correlations as well as clustering. We then empirically measure these quantities on two real life folksonomies, the popular online photo sharing site Flickr and the bookmarking site CiteULike. We find that these systems share similar qualitative features with the majority of complex networks that have been previously studied. We propose that the quantities and methodology described here can be used as a standard tool in measuring the structure of tagged networks.

  8. 16 CFR 500.25 - Net quantity, average quantity, permitted variations.

    Science.gov (United States)

    2010-01-01

    ... good distribution practice and which unavoidably result in change of weight or mass or measure. (c... good packaging practice: Provided, that such variations shall not be permitted to such extent that the... 16 Commercial Practices 1 2010-01-01 2010-01-01 false Net quantity, average quantity, permitted...

  9. Optimizing basin-scale coupled water quantity and water quality management with stochastic dynamic programming

    DEFF Research Database (Denmark)

    Davidsen, Claus; Liu, Suxia; Mo, Xingguo

    2015-01-01

    Few studies address water quality in hydro-economic models, which often focus primarily on optimal allocation of water quantities. Water quality and water quantity are closely coupled, and optimal management with focus solely on either quantity or quality may cause large costs in terms of the oth......-er component. In this study, we couple water quality and water quantity in a joint hydro-economic catchment-scale optimization problem. Stochastic dynamic programming (SDP) is used to minimize the basin-wide total costs arising from water allocation, water curtailment and water treatment. The simple water...... quality module can handle conservative pollutants, first order depletion and non-linear reactions. For demonstration purposes, we model pollutant releases as biochemical oxygen demand (BOD) and use the Streeter-Phelps equation for oxygen deficit to compute the resulting min-imum dissolved oxygen...

  10. Studies related to the development of the viking 1975 labeled release experiment

    International Nuclear Information System (INIS)

    Devincenzi, D.L.; Deal, P.H.

    1976-04-01

    The labeled release life detection experiment on the Viking 1975 Mars mission is based on the concept that microorganisms will metabolize radioactive organic substrates in a nutrient medium and release radioactive carbon dioxide. Several experiments, using laboratory equipment, were carried out to evaluate various aspects of the concept. Results indicate: (1) label is released by sterilization-treated soil, (2) substantial quantities of label are retained in solution under basic conditions, (3) the substrate used, as well as position of label in the molecule, affect release of label, (4) label release is depressed by radiolytic decomposition of substrates, and (5) About 100,000 organisms are required to produce a detectable response. These results, suggest additional areas for testing, add to the data base for interpretation of flight results, and have significance for broader application of this technique for assessing microbial activity. (Author)

  11. Radiation quantities and units. ICRU report 33

    International Nuclear Information System (INIS)

    Anon.

    1987-01-01

    This report supersedes ICRU Report 19. Since ICRU Report 19 was published, a number of discussions have taken place between members of the Report Committee on Fundamental Quantities and Units and other workers in the field. Some of these discussions have resulted in the acceptance of certain modifications in the material set out in Report 19 and these modifications are incorporated in the current report. In addition, there has been some expansion and rearrangement of the material in the earlier report. It is recommended that energy state be inserted into the definition of activity and that the word transformation be replaced by transition. These modifications have now been incorporated into the current definition. Helpful comments on the previous quantities and units report have resulted in clarification of several points in the present Report. In line with providing more didactic material and useful source material for other ICRU reports, the general considerations in subsection I.A of Report 19 have been expanded and placed in a separate subsection. The additional material includes discussions of four terms that are used in this document - quantity, unit, stochastic, and non-stochastic - along with a brief discussion of the mathematical formalism used in ICRU reports. 11 refs., 4 tabs

  12. Quantity discrimination in wolves (Canis lupus

    Directory of Open Access Journals (Sweden)

    Ewelina eUtrata

    2012-11-01

    Full Text Available Quantity discrimination has been studied extensively in different non-human animal species. In the current study, we tested eleven hand-raised wolves (Canis lupus in a two-way choice task. We placed a number of food items (one to four sequentially into two opaque cans and asked the wolves to choose the larger amount. Moreover, we conducted two additional control conditions to rule out non-numerical properties of the presentation that the animals might have used to make the correct choice. Our results showed that wolves are able to make quantitative judgments at the group, but also at the individual level even when alternative strategies such as paying attention to the surface area or time and total amount are ruled out. In contrast to previous canine studies on dogs (Canis familiaris and coyotes (Canis latrans, our wolves’ performance did not improve with decreasing ratio, referred to as Weber’s law. However, further studies using larger quantities than we used in the current setup are still needed to determine whether and when wolves’ quantity discrimination conforms to Weber’s law.

  13. Release of Hormones from Conjugates: Chloroplast Expression of β-Glucosidase Results in Elevated Phytohormone Levels Associated with Significant Increase in Biomass and Protection from Aphids or Whiteflies Conferred by Sucrose Esters1[C][OA

    Science.gov (United States)

    Jin, Shuangxia; Kanagaraj, Anderson; Verma, Dheeraj; Lange, Theo; Daniell, Henry

    2011-01-01

    Transplastomic tobacco (Nicotiana tabacum) plants expressing β-glucosidase (Bgl-1) show modified development. They flower 1 month earlier with an increase in biomass (1.9-fold), height (1.5-fold), and leaf area (1.6-fold) than untransformed plants. Trichome density on the upper and lower leaf surfaces of BGL-1 plants increase by 10- and 7-fold, respectively, harboring 5-fold more glandular trichomes (as determined by rhodamine B staining), suggesting that BGL-1 lines produce more sugar esters than control plants. Gibberellin (GA) levels were investigated because it is a known regulator of flowering time, plant height, and trichome development. Both GA1 and GA4 levels are 2-fold higher in BGL-1 leaves than in untransformed plants but do not increase in other organs. In addition, elevated levels of other plant hormones, including zeatin and indole-3-acetic acid, are observed in BGL-1 lines. Protoplasts from BGL-1 lines divide and form calli without exogenous hormones. Cell division in protoplasts is enhanced 7-fold in the presence of exogenously applied zeatin-O-glucoside conjugate, indicating the release of active hormones from their conjugates. Whitefly (Bemisia tabaci) and aphid (Myzus persicae) populations in control plants are 18 and 15 times higher than in transplastomic lines, respectively. Lethal dose to kill 50% of the test population values of 26.3 and 39.2 μg per whitefly and 23.1 and 35.2 μg per aphid for BGL-1 and untransformed control exudates, respectively, confirm the enhanced toxicity of transplastomic exudates. These data indicate that increase in sugar ester levels in BGL-1 lines might function as an effective biopesticide. This study provides a novel strategy for designing plants for enhanced biomass production and insect control by releasing plant hormones or sugar esters from their conjugates stored within their chloroplasts. PMID:21068365

  14. Release of hormones from conjugates: chloroplast expression of β-glucosidase results in elevated phytohormone levels associated with significant increase in biomass and protection from aphids or whiteflies conferred by sucrose esters.

    Science.gov (United States)

    Jin, Shuangxia; Kanagaraj, Anderson; Verma, Dheeraj; Lange, Theo; Daniell, Henry

    2011-01-01

    Transplastomic tobacco (Nicotiana tabacum) plants expressing β-glucosidase (Bgl-1) show modified development. They flower 1 month earlier with an increase in biomass (1.9-fold), height (1.5-fold), and leaf area (1.6-fold) than untransformed plants. Trichome density on the upper and lower leaf surfaces of BGL-1 plants increase by 10- and 7-fold, respectively, harboring 5-fold more glandular trichomes (as determined by rhodamine B staining), suggesting that BGL-1 lines produce more sugar esters than control plants. Gibberellin (GA) levels were investigated because it is a known regulator of flowering time, plant height, and trichome development. Both GA(1) and GA(4) levels are 2-fold higher in BGL-1 leaves than in untransformed plants but do not increase in other organs. In addition, elevated levels of other plant hormones, including zeatin and indole-3-acetic acid, are observed in BGL-1 lines. Protoplasts from BGL-1 lines divide and form calli without exogenous hormones. Cell division in protoplasts is enhanced 7-fold in the presence of exogenously applied zeatin-O-glucoside conjugate, indicating the release of active hormones from their conjugates. Whitefly (Bemisia tabaci) and aphid (Myzus persicae) populations in control plants are 18 and 15 times higher than in transplastomic lines, respectively. Lethal dose to kill 50% of the test population values of 26.3 and 39.2 μg per whitefly and 23.1 and 35.2 μg per aphid for BGL-1 and untransformed control exudates, respectively, confirm the enhanced toxicity of transplastomic exudates. These data indicate that increase in sugar ester levels in BGL-1 lines might function as an effective biopesticide. This study provides a novel strategy for designing plants for enhanced biomass production and insect control by releasing plant hormones or sugar esters from their conjugates stored within their chloroplasts.

  15. The Acquisition of Quantity Contrasts in Guina-ang Bontok

    Science.gov (United States)

    Aoyama, Katsura; Reid, Lawrence A.

    2016-01-01

    This study reports on the acquisition of quantity contrasts in Guina-ang Bontok, an indigenous language spoken in the Philippines. Four-year-old and 5-year-old children's perception and production of quantity contrasts were examined using a pair of names that contrast in the quantity of the medial nasal. Frequencies of the quantity contrast were…

  16. Significant event of patient radiation protection in radiotherapy (criterion 2.1): declaration and rating on the ASN-SFRO scale - ASN guide nr 16 - Release of the 01/01/2010

    International Nuclear Information System (INIS)

    2010-01-01

    This document brings together all the tools for the management of a significant event in radiation protection concerning a patient in radiotherapy. It contains the declaration form, a model for the reporting of significant events, and the ASN-SFRO scale which allows the event to be rated. After a presentation of the regulatory context and references, of the scope of application, this guide addresses the declaration of a significant event: general principles, definition of the 2.1 criterion, examples, delays and modalities of declaration, addressees of a declaration. It addresses the reporting of a significant event: general principles, sending delays and modalities. It addresses the rating on the ASN-SFRO scale: general principles, scale, and rating process. The last part deals with public information

  17. Significant event of patient radiation protection in radiotherapy (criterion 2.1): declaration and rating on the ASN-SFRO scale - ASN guide no. 16 - Release of 17/07/2015

    International Nuclear Information System (INIS)

    2015-01-01

    This document is an update of the previous version from October 2010. It brings together all the tools for the management of a significant event in radiation protection concerning a patient in radiotherapy. It contains the declaration form, a model for the reporting of significant events, and the ASN-SFRO scale which allows the event to be rated. After a presentation of the regulatory context and references, of the scope of application, this guide addresses the declaration of a significant event: general principles, definition of the 2.1 criterion, examples, delays and modalities of declaration, addressees of a declaration. It addresses the reporting of a significant event: general principles, sending delays and modalities. It addresses the rating on the ASN-SFRO scale: general principles, scale, and rating process. The last part deals with public information

  18. Method of Converting Wheat Flour Quantity into Rice Flour Quantity in Cookies (Part-1)

    OpenAIRE

    村田,美穂子; 髙橋,由加

    2016-01-01

    A method of converting the wheat flour quantity of a recipe of wheat-flour cookies into the rice flour quantity of a recipe of rice-flour cookies used domestically for wheat-allergic children was studied. The proportion of the water content with respect to the flour content (the wheat or rice flour content) in cut cookies prepared according to a commercially available recipe was obtained. Next, four types of rice-flour cookies were prepared according to a recipe for wheat-flour cookies using ...

  19. Effective dose: a radiation protection quantity

    CERN Document Server

    Menzel, H G

    2012-01-01

    Modern radiation protection is based on the principles of justification, limitation, and optimisation. Assessment of radiation risks for individuals or groups of individuals is, however, not a primary objective of radiological protection. The implementation of the principles of limitation and optimisation requires an appropriate quantification of radiation exposure. The International Commission on Radiological Protection (ICRP) has introduced effective dose as the principal radiological protection quantity to be used for setting and controlling dose limits for stochastic effects in the regulatory context, and for the practical implementation of the optimisation principle. Effective dose is the tissue weighted sum of radiation weighted organ and tissue doses of a reference person from exposure to external irradiations and internal emitters. The specific normalised values of tissue weighting factors are defined by ICRP for individual tissues, and used as an approximate age- and sex-averaged representation of th...

  20. The 2017 Release Cloudy

    Science.gov (United States)

    Ferland, G. J.; Chatzikos, M.; Guzmán, F.; Lykins, M. L.; van Hoof, P. A. M.; Williams, R. J. R.; Abel, N. P.; Badnell, N. R.; Keenan, F. P.; Porter, R. L.; Stancil, P. C.

    2017-10-01

    We describe the 2017 release of the spectral synthesis code Cloudy, summarizing the many improvements to the scope and accuracy of the physics which have been made since the previous release. Exporting the atomic data into external data files has enabled many new large datasets to be incorporated into the code. The use of the complete datasets is not realistic for most calculations, so we describe the limited subset of data used by default, which predicts significantly more lines than the previous release of Cloudy. This version is nevertheless faster than the previous release, as a result of code optimizations. We give examples of the accuracy limits using small models, and the performance requirements of large complete models. We summarize several advances in the H- and He-like iso-electronic sequences and use our complete collisional-radiative models to establish the densities where the coronal and local thermodynamic equilibrium approximations work.

  1. The Effect of Quantity, Quality and Timing of Headquarters-Initiated Knowledge Flows on Subsidiary Performance

    DEFF Research Database (Denmark)

    Tran, Yen; Mahnke, Volker; Ambos, Björn

    2010-01-01

    quality/performance relationship and a curvilinear quantity/performance relationship, indicating that too much knowledge sharing can be detrimental to the receiving subsidiary. Most importantly, we show that the timing of a knowledge flow significantly affects subsidiary sales performance....

  2. Metal lost and found: dissipative uses and releases of copper in the United States 1975-2000.

    Science.gov (United States)

    Lifset, Reid J; Eckelman, Matthew J; Harper, E M; Hausfather, Zeke; Urbina, Gonzalo

    2012-02-15

    Metals are used in a variety of ways, many of which lead to dissipative releases to the environment. Such releases are relevant from both a resource use and an environmental impact perspective. We present a historical analysis of copper dissipative releases in the United States from 1975 to 2000. We situate all dissipative releases in copper's life cycle and introduce a conceptual framework by which copper dissipative releases may be categorized in terms of intentionality of use and release. We interpret our results in the context of larger trends in production and consumption and government policies that have served as drivers of intentional copper releases from the relevant sources. Intentional copper releases are found to be both significant in quantity and highly variable. In 1975, for example, the largest source of intentional releases was from the application of copper-based pesticides, and this decreased more than 50% over the next 25 years; all other sources of intentional releases increased during that period. Overall, intentional copper releases decreased by approximately 15% from 1975 to 2000. Intentional uses that are unintentionally released such as copper from roofing, increased by the same percentage. Trace contaminant sources such as fossil fuel combustion, i.e., sources where both the use and the release are unintended, increased by nearly 50%. Intentional dissipative uses are equivalent to 60% of unintentional copper dissipative releases and more than five times that from trace sources. Dissipative copper releases are revealed to be modest when compared to bulk copper flows in the economy, and we introduce a metric, the dissipation index, which may be considered an economy-wide measure of resource efficiency for a particular substance. We assess the importance of dissipative releases in the calculation of recycling rates, concluding that the inclusion of dissipation in recycling rate calculations has a small, but discernible, influence, and should

  3. Methane release

    International Nuclear Information System (INIS)

    Seifert, M.

    1999-01-01

    The Swiss Gas Industry has carried out a systematic, technical estimate of methane release from the complete supply chain from production to consumption for the years 1992/1993. The result of this survey provided a conservative value, amounting to 0.9% of the Swiss domestic output. A continuation of the study taking into account new findings with regard to emission factors and the effect of the climate is now available, which provides a value of 0.8% for the target year of 1996. These results show that the renovation of the network has brought about lower losses in the local gas supplies, particularly for the grey cast iron pipelines. (author)

  4. Category 3 threshold quantities for hazard categorization of nonreactor facilities

    International Nuclear Information System (INIS)

    Mandigo, R.L.

    1996-01-01

    This document provides the information necessary to determine Hazard Category 3 threshold quantities for those isotopes of interest not listed in WHC-CM-4-46, Section 4, Table 1.''Threshold Quantities.''

  5. Discounting of quantity surveying fees in South Africa

    African Journals Online (AJOL)

    by clients have forced Quantity Surveying firms into competition with ... Furthermore, 43% of consulting engineering firms were discounting their fees at a rate of .... Quantity. Surveying services are also offered in the fields of dispute resolution,.

  6. Rainwater in Egypt: quantity, distribution and harvesting

    Directory of Open Access Journals (Sweden)

    H.I. ABDEL-SHAFY

    2010-11-01

    Full Text Available Egypt has limited water resources, and it will be under water stress within the year 2030. Therefore, Egypt should consider the natural and non-conventional water resources to overcome such problem. Rain harvesting is one solution; but not all; particularly on the north coast by the Mediterranean Sea and the Red sea. In this paper, the rainwater issue is reviewed and discussed in terms of the quantities and distribution at different selected areas in Egypt. The amount of rain falls at different location in Egypt was collected for a period of 16 months. The data indicated that rainfall in Egypt is very scarce, with an annual average of 12 mm and ranges from 0 mm/year in the desert to 200 mm/year in the north coastal region. The maximum total amount of rain does not exceed 1.8 billion m3per year. However, the average annual amount of rainfall water that is effectively utilized for agriculture purposes is estimated to be 1 billion m3. Harvesting pilot plant was constructed and implemented in Alexandria directly on the Mediterranean Sea. The harvested rain was used for irrigation and treated for drinking. It was, therefore, recommended to develop sustainable catchments at appropriate locations in the rain-fed areas at the north coast as well as cost effective grafting of the indigenous technologies with the innovative techniques.

  7. 41 CFR 101-27.102 - Economic order quantity principle.

    Science.gov (United States)

    2010-07-01

    ... MANAGEMENT 27.1-Stock Replenishment § 101-27.102 Economic order quantity principle. The economic order quantity (EOQ) principle is a means for achieving economical inventory management. Application of the EOQ... 41 Public Contracts and Property Management 2 2010-07-01 2010-07-01 true Economic order quantity...

  8. Six categories of ionizing radiation quantities practical in various fields

    International Nuclear Information System (INIS)

    Zheng Junzheng; Zhuo Weihai

    2011-01-01

    This paper is the part of review on the evolvement of the systems for ionizing radiation quantities and units. In the paper, for better understanding and correct use of the relevant quantities of ionizing radiation, the major ionizing radiation quantities in various fields are divided into six categories. (authors)

  9. 7 CFR 61.102 - Determination of quantity index.

    Science.gov (United States)

    2010-01-01

    ... the quantity index shall equal four times percentage of oil plus six times percentage of ammonia, plus 5. (b) For American Pima cottonseed the quantity index shall equal four times percentage of oil... 7 Agriculture 3 2010-01-01 2010-01-01 false Determination of quantity index. 61.102 Section 61.102...

  10. Spray drying of silica microparticles for sustained release application with a new sol-gel precursor.

    Science.gov (United States)

    Wang, Bifeng; Friess, Wolfgang

    2017-10-30

    A new precursor, tetrakis(2-methoxyethyl) orthosilicate (TMEOS) was used to fabricate microparticles for sustained release application, specifically for biopharmaceuticals, by spray drying. The advantages of TMEOS over the currently applied precursors are its water solubility and hydrolysis at moderate pH without the need of organic solvents or catalyzers. Thus a detrimental effect on biomolecular drug is avoided. By generating spray-dried silica particles encapsulating the high molecular weight model compound FITC-dextran 150 via the nano spray dryer Büchi-90, we demonstrated how formulation parameters affect and enable control of drug release properties. The implemented strategies to regulate release included incorporating different quantities of dextrans with varying molecular weight as well as adjusting the pH of the precursor solution to modify the internal microstructures. The addition of dextran significantly altered the released amount, while the release became faster with increasing dextran molecular weight. A sustained release over 35days could be achieved with addition of 60 kD dextran. The rate of FITC-Dextran 150 release from the dextran 60 containing particles decreased with higher precursor solution pH. In conclusion, the new precursor TMEOS presents a promising alternative sol-gel technology based carrier material for sustained release application of high molecular weight biopharmaceutical drugs. Copyright © 2017 Elsevier B.V. All rights reserved.

  11. EFFECT OF SALES PROMOTION SCHEMES ON PURCHASE QUANTITY: A STUDY OF MALAYSIAN CONSUMERS

    Directory of Open Access Journals (Sweden)

    Hawa JALLOW

    2016-11-01

    Full Text Available The research aims to study the effect of sales promotion on the purchase quantity and recommend sales promotional means and methods that could improve sales for retail sector in Malaysia. The impact of coupons, bonus packages, premiums, free samples and price discount is measured on purchase quantity of Malaysian retail consumers. Empirical data is gathered from 150 respondents using self-administered questionnaire and analyzed using correlation and regression analysis to examine the relationship between variables. The findings of the study reveal that all independent variables influences purchase quantity positively and significantly while free samples and price discounts are most influential factors for Malaysian market.

  12. The covariance matrix of derived quantities and their combination

    International Nuclear Information System (INIS)

    Zhao, Z.; Perey, F.G.

    1992-06-01

    The covariance matrix of quantities derived from measured data via nonlinear relations are only approximate since they are functions of the measured data taken as estimates for the true values of the measured quantities. The evaluation of such derived quantities entails new estimates for the true values of the measured quantities and consequently implies a modification of the covariance matrix of the derived quantities that was used in the evaluation process. Failure to recognize such an implication can lead to inconsistencies between the results of different evaluation strategies. In this report we show that an iterative procedure can eliminate such inconsistencies

  13. Determination of dosimetric quantities in pediatric abdominal computed tomography scans

    Energy Technology Data Exchange (ETDEWEB)

    Jornada, Tiago da Silva [Universidade Federal de Sao Paulo (UNIFESP), Sao Paulo, SP (Brazil). Escola Paulista de Medicina. Dept. de Diagnostipo por Imagem; Silva, Teogenes Augusto da, E-mail: silvata@cdtn.br [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil)

    2014-09-15

    Objective: aiming at contributing to the knowledge on doses in computed tomography (CT), this study has the objective of determining dosimetric quantities associated with pediatric abdominal CT scans, comparing the data with diagnostic reference levels (DRL). Materials and methods: the study was developed with a Toshiba Asteion single-slice CT scanner and a GE BrightSpeed multi-slice CT unit in two hospitals. Measurements were performed with a pencil-type ionization chamber and a 16 cm-diameter polymethylmethacrylate trunk phantom. Results: No significant difference was observed in the values for weighted air kerma index (C{sub W}), but the differences were relevant in values for volumetric air kerma index (C{sub VOL}), air kerma-length product (P{sub KL,CT}) and effective dose. Conclusion: Only the CW values were lower than the DRL, suggesting that dose optimization might not be necessary. However, P{sub KL,CT} and effective dose values stressed that there still is room for reducing pediatric radiation doses. The present study emphasizes the importance of determining all dosimetric quantities associated with CT scans. (author)

  14. Determination of dosimetric quantities in pediatric abdominal computed tomography scans*

    Science.gov (United States)

    Jornada, Tiago da Silva; da Silva, Teógenes Augusto

    2014-01-01

    Objective Aiming at contributing to the knowledge on doses in computed tomography (CT), this study has the objective of determining dosimetric quantities associated with pediatric abdominal CT scans, comparing the data with diagnostic reference levels (DRL). Materials and methods The study was developed with a Toshiba Asteion single-slice CT scanner and a GE BrightSpeed multi-slice CT unit in two hospitals. Measurements were performed with a pencil-type ionization chamber and a 16 cm-diameter polymethylmethacrylate trunk phantom. Results No significant difference was observed in the values for weighted air kerma index (CW), but the differences were relevant in values for volumetric air kerma index (CVOL), air kerma-length product (PKL,CT) and effective dose. Conclusion Only the CW values were lower than the DRL, suggesting that dose optimization might not be necessary. However, PKL,CT and effective dose values stressed that there still is room for reducing pediatric radiation doses. The present study emphasizes the importance of determining all dosimetric quantities associated with CT scans. PMID:25741103

  15. Unified Symmetry and Conserved Quantities of Mechanical System in Phase Space

    International Nuclear Information System (INIS)

    Fang Jianhui; Ding Ning; Wang Peng

    2006-01-01

    In this paper, a new symmetry and its conserved quantities of a mechanical system in phase space are studied. The definition of this new symmetry, i.e., a unified one is presented, and the criterion of this symmetry is also given. The Noether, the generalized Hojman and the Mei conserved quantities of the unified symmetry of the system are obtained. The unified symmetry contains the Noether, the Lie and the Mei symmetries, and has more generalized significance.

  16. Comparison of metal release from various metallic biomaterials in vitro.

    Science.gov (United States)

    Okazaki, Yoshimitsu; Gotoh, Emiko

    2005-01-01

    To investigate the metal release of each base and alloying elements in vitro, SUS316L stainless steel, Co-Cr-Mo casting alloy, commercially pure Ti grade 2, and Ti-6Al-4V, V-free Ti-6Al-7Nb and Ti-15Zr-4Nb-4Ta alloys were immersed in various solutions, namely, alpha-medium, PBS(-), calf serum, 0.9% NaCl, artificial saliva, 1.2 mass% L-cysteine, 1 mass% lactic acid and 0.01 mass% HCl for 7d. The difference in the quantity of Co released from the Co-Cr-Mo casting alloy was relatively small in all the solutions. The quantities of Ti released into alpha-medium, PBS(-), calf serum, 0.9% NaCl and artificial saliva were much lower than those released into 1.2% L-cysteine, 1% lactic acid and 0.01% HCl. The quantity of Fe released from SUS316L stainless steel decreased linearly with increasing pH. On the other hand, the quantity of Ti released from Ti materials increased with decreasing pH, and it markedly attenuated at pHs of approximately 4 and higher. The quantity of Ni released from stainless steel gradually decreased with increasing pH. The quantities of Al released from the Ti-6Al-4V and Ti-6Al-7Nb alloys gradually decreased with increasing pH. A small V release was observed in calf serum, PBS(-), artificial saliva, 1% lactic acid, 1.2% l-cysteine and 0.01% HCl. The quantity of Ti released from the Ti-15Zr-4Nb-4Ta alloy was smaller than those released from the Ti-6Al-4V and Ti-6Al-7Nb alloys in all the solutions. In particular, it was approximately 30% or smaller in 1% lactic acid, 1.2% L-cysteine and 0.01% HCl. The quantity of (Zr + Nb + Ta) released was also considerably lower than that of (Al + Nb) or (Al + V) released. Therefore, the Ti-15Zr-4Nb-4Ta alloy with its low metal release in vitro is considered advantageous for long-term implants. Copyright 2004 Elsevier Ltd.

  17. Determination of accident related release data

    International Nuclear Information System (INIS)

    Koch, W.; Nolte, O.; Lange, F.; Martens, R.

    2004-01-01

    For accident safety analyses, for the assessment of potential radiological consequences, for the review of current requirements of the Transport Regulations and for their possible further development as well as for the demonstration that radioactive materials such as LDM candidate material fulfil the regulatory requirements reliable release data following mechanical impact are required. This is definitely one of the demanding issues in the field of transport safety of radioactive materials. In this context special attention has to be paid to radioactive wastes immobilised in brittle materials, e.g. cement/concrete, glass, ceramics or other brittle materials such as fresh and spent fuel. In this presentation we report on a long-term experimental program aiming at improving the general physical understanding of the release process as well as the quantity and the quality of release data. By combining laboratory experiments using small scale test specimens with a few key scaling experiments with large scale test objects significant progress was achieved to meet this objective. The laboratory equipment enables the in-situ determination of the amount and aerodynamic size distribution of the airborne particles generated upon impact of the test specimen on a hard target. Impact energies cover the range experienced in transport accidents including aircraft accidents. The well defined experimental boundary conditions and the good reproducibility of the experimental procedure allowed for systematic studies to exactly measure the amount and aerodynamic size distribution of the airborne release and to quantify its dependence on relevant parameters such as energy input, material properties, and specimen geometry. The experimental program was performed within the scope of various national and international (e.g. EU-funded) projects. The small scale experiments with brittle materials revealed a pronounced universality of the airborne release in view of the material properties and

  18. A geochemical module for "AMDTreat" to compute caustic quantity, effluent quantity, and sludge volume

    Science.gov (United States)

    Cravotta,, Charles A.; Parkhurst, David L.; Means, Brent P; McKenzie, Bob; Morris, Harry; Arthur, Bill

    2010-01-01

    Treatment with caustic chemicals typically is used to increase pH and decrease concentrations of dissolved aluminum, iron, and/or manganese in largevolume, metal-laden discharges from active coal mines. Generally, aluminum and iron can be removed effectively at near-neutral pH (6 to 8), whereas active manganese removal requires treatment to alkaline pH (~10). The treatment cost depends on the specific chemical used (NaOH, CaO, Ca(OH)2, Na2CO3, or NH3) and increases with the quantities of chemical added and sludge produced. The pH and metals concentrations do not change linearly with the amount of chemical added. Consequently, the amount of caustic chemical needed to achieve a target pH and the corresponding effluent composition and sludge volume can not be accurately determined without empirical titration data or the application of geochemical models to simulate the titration of the discharge water with caustic chemical(s). The AMDTreat computer program (http://amd.osmre.gov/ ) is widely used to compute costs for treatment of coal-mine drainage. Although AMDTreat can use results of empirical titration with industrial grade caustic chemicals to compute chemical costs for treatment of net-acidic or net-alkaline mine drainage, such data are rarely available. To improve the capability of AMDTreat to estimate (1) the quantity and cost of caustic chemicals to attain a target pH, (2) the concentrations of dissolved metals in treated effluent, and (3) the volume of sludge produced by the treatment, a titration simulation is being developed using the geochemical program PHREEQC (wwwbrr.cr.usgs.gov/projects/GWC_coupled/phreeqc/) that will be coupled as a module to AMDTreat. The simulated titration results can be compared with or used in place of empirical titration data to estimate chemical quantities and costs. This paper describes the development, evaluation, and potential utilization of the PHREEQC titration module for AMDTreat.

  19. A New type of conserved quantity deduced from Mei symmetry of nonholonomic systems in terms of quasi-coordinates

    International Nuclear Information System (INIS)

    Ting, Pang; Jian-Hui, Fang; Ming-Jiang, Zhang; Peng, Lin; Kai, Lu

    2009-01-01

    This paper studies the new type of conserved quantity which is directly induced by Mei symmetry of nonholonomic systems in terms of quasi-coordinates. A coordination function is introduced, and the conditions for the existence of the new conserved quantities as well as their forms are proposed. Some special cases are given to illustrate the generalized significance of the new type conserved quantity. Finally, an illustrated example is given to show the application of the nonholonomic system's results. (general)

  20. Bulky waste quantities and treatment methods in Denmark

    DEFF Research Database (Denmark)

    Larsen, Anna Warberg; Petersen, Claus; Christensen, Thomas Højlund

    2012-01-01

    were identified of which ten were recyclable and constituted 50–60% of the total quantity. The others were combustible waste for incineration (30–40%) and non-combustible waste for landfilling (10%). The largest fractions by mass were combustible waste, bricks and tile, concrete, non-combustible waste....... In addition a sorting analysis was conducted on combustible waste, which is a major fraction of bulky waste in Denmark. The generation of bulky waste was found to be 150–250 kg capita−1 year−1, and 90% of the waste was collected at recycling centres; the rest through kerbside collection. Twelve main fractions......, wood, and metal scrap, which together made up more than 90% of the total waste amounts. The amount of combustible waste could be significantly reduced through better sorting. Many of the waste fractions consisted of composite products that underwent thorough separation before being recycled...

  1. Uranium chemistry: significant advances

    International Nuclear Information System (INIS)

    Mazzanti, M.

    2011-01-01

    The author reviews recent progress in uranium chemistry achieved in CEA laboratories. Like its neighbors in the Mendeleev chart uranium undergoes hydrolysis, oxidation and disproportionation reactions which make the chemistry of these species in water highly complex. The study of the chemistry of uranium in an anhydrous medium has led to correlate the structural and electronic differences observed in the interaction of uranium(III) and the lanthanides(III) with nitrogen or sulfur molecules and the effectiveness of these molecules in An(III)/Ln(III) separation via liquid-liquid extraction. Recent work on the redox reactivity of trivalent uranium U(III) in an organic medium with molecules such as water or an azide ion (N 3 - ) in stoichiometric quantities, led to extremely interesting uranium aggregates particular those involved in actinide migration in the environment or in aggregation problems in the fuel processing cycle. Another significant advance was the discovery of a compound containing the uranyl ion with a degree of oxidation (V) UO 2 + , obtained by oxidation of uranium(III). Recently chemists have succeeded in blocking the disproportionation reaction of uranyl(V) and in stabilizing polymetallic complexes of uranyl(V), opening the way to to a systematic study of the reactivity and the electronic and magnetic properties of uranyl(V) compounds. (A.C.)

  2. Estimated quantities of residual materials in a KBS-3H repository at Olkiluoto

    International Nuclear Information System (INIS)

    Hagros, Annika

    2008-12-01

    The quantities of residual materials in a KBS-3H type repository have been estimated in this report. The repository is assumed to be constructed at Olkiluoto in Eurajoki, Western Finland. Both the total quantities of the materials introduced into the repository and the quantities of materials that remain in the repository after closure have been calculated. The calculations are largely based on a similar work regarding the material quantities in the Finnish KBS-3V repository and the main goal has been to identify the differences between the KBS-3H and KBS-3V repositories with respect to the type and quantities of residual materials. As the design of the KBS-3H repository is not final yet, the results are only preliminary. Several alternative designs were assumed in the calculations, resulting in different total quantities of materials. The design alternatives that had the greatest effect on the total material quantities were the two different tunnel backfill options, bentonite-crushed rock and Friedland clay. If Friedland clay is used instead of a bentonite-crushed rock mixture, the total quantity of pyrite remaining in the repository is 20 times larger and the quantities of organic materials and gypsum are also increased significantly. The other design alternatives did not have a substantial effect on the total material quantities. The remaining quantity of cement can be reduced by some 20% by selecting the silica grouting alternative in the sealing of the rock mass and low-pH cement in the shotcreting of the repository, instead of using the ordinary cement alternatives. If the total quantity of steel should be minimised, the use of the DAWE design alternative would be better than the Basic Design, although the total reduction would be less than 10%. The main difference between the different drift end plug alternatives is related to the total remaining quantity of silica, which is some 80% smaller if the rock plug is used instead of the LHHP (Low Heat High

  3. Estimated quantities of residual materials in a KBS-3H repository at Olkiluoto

    Energy Technology Data Exchange (ETDEWEB)

    Hagros, Annika (Sannio and Riekkola OY (Finland))

    2008-12-15

    The quantities of residual materials in a KBS-3H type repository have been estimated in this report. The repository is assumed to be constructed at Olkiluoto in Eurajoki, Western Finland. Both the total quantities of the materials introduced into the repository and the quantities of materials that remain in the repository after closure have been calculated. The calculations are largely based on a similar work regarding the material quantities in the Finnish KBS-3V repository and the main goal has been to identify the differences between the KBS-3H and KBS-3V repositories with respect to the type and quantities of residual materials. As the design of the KBS-3H repository is not final yet, the results are only preliminary. Several alternative designs were assumed in the calculations, resulting in different total quantities of materials. The design alternatives that had the greatest effect on the total material quantities were the two different tunnel backfill options, bentonite-crushed rock and Friedland clay. If Friedland clay is used instead of a bentonite-crushed rock mixture, the total quantity of pyrite remaining in the repository is 20 times larger and the quantities of organic materials and gypsum are also increased significantly. The other design alternatives did not have a substantial effect on the total material quantities. The remaining quantity of cement can be reduced by some 20% by selecting the silica grouting alternative in the sealing of the rock mass and low-pH cement in the shotcreting of the repository, instead of using the ordinary cement alternatives. If the total quantity of steel should be minimised, the use of the DAWE design alternative would be better than the Basic Design, although the total reduction would be less than 10%. The main difference between the different drift end plug alternatives is related to the total remaining quantity of silica, which is some 80% smaller if the rock plug is used instead of the LHHP (Low Heat High

  4. Physical quantities, their role and treatment in gasflow measurement techniques

    International Nuclear Information System (INIS)

    Narjes, L.

    1977-06-01

    We begin by taking a closer look at the concepts physical quantity, dimension and unit of measurement. Then a survey is given of the physical quantities applied in gasflow measurement techniques. Here the volume-, as well as the mass-flow rate, as derived quantities are of particular interest. The application of these quantities in relation to the legal units of measurement is specifically described. In addition the quantity equation and further the quantity equation adapted to the use of suitable units and their modes of application are compared. In the appendix four examples clarify these modes. Special attention is paid to the quantity equation adapted to practically oriented units. The applications of this type of equation in VDI regulations, standards and other technical guidelines for measurement of flow are mentioned. Moreover, the meaning of the standard state for the comparison of flows of gaseous fluids is illustrated. The difficulties concerning an international agreement on uniform standard temperature are explained. Starting from there, the advantages of the fundamental quantity 'amount of substance' applied to the measurement of flow are described. The use of this quantity for the thermodynamic state of ideal and real gases, respectively gas mixtures, is demonstrated in the appendix by an example. (orig.) [de

  5. By Default: The Effect of Prepopulated Prescription Quantities on Opioid Prescribing in the Emergency Department.

    Science.gov (United States)

    Santistevan, Jamie R; Sharp, Brian R; Hamedani, Azita G; Fruhan, Scott; Lee, Andrew W; Patterson, Brian W

    2018-03-01

    Opioid prescribing patterns have come under increasing scrutiny with the recent rise in opioid prescriptions, opioid misuse and abuse, and opioid-related adverse events. To date, there have been limited studies on the effect of default tablet quantities as part of emergency department (ED) electronic order entry. Our goal was to evaluate opioid prescribing patterns before and after the removal of a default quantity of 20 tablets from ED electronic order entry. We performed a retrospective observational study at a single academic, urban ED with 58,000 annual visits. We identified all adult patients (18 years or older) seen in the ED and discharged home with prescriptions for tablet forms of hydrocodone and oxycodone (including mixed formulations with acetaminophen). We compared the quantity of tablets prescribed per opioid prescription 12 months before and 10 months after the electronic order-entry prescription default quantity of 20 tablets was removed and replaced with no default quantity. No specific messaging was given to providers, to avoid influencing prescribing patterns. We used two-sample Wilcoxon rank-sum test, two-sample test of proportions, and Pearson's chi-squared tests where appropriate for statistical analysis. A total of 4,104 adult patients received discharge prescriptions for opioids in the pre-intervention period (151.6 prescriptions per 1,000 discharged adult patients), and 2,464 post-intervention (106.69 prescriptions per 1,000 discharged adult patients). The median quantity of opioid tablets prescribed decreased from 20 (interquartile ration [IQR] 10-20) to 15 (IQR 10-20) (pdefault quantity. While the most frequent quantity of tablets received in both groups was 20 tablets, the proportion of patients who received prescriptions on discharge that contained 20 tablets decreased from 0.5 (95% confidence interval [CI] [0.48-0.52]) to 0.23 (95% CI [0.21-0.24]) (pdefault quantity removal. Although the median number of tablets differed significantly

  6. Skin dose estimation due to a contamination by a radionuclide β emitter: are doses equivalent good estimator of protection quantities?

    International Nuclear Information System (INIS)

    Bourgois, L.

    2011-01-01

    When handling radioactive β emitters, measurements in terms of personal dose equivalents H p (0.07) are used to estimate the equivalent dose limit to skin or extremities given by regulations. First of all, analytical expressions for individual dose equivalents H p (0.07) and equivalent doses to the extremities H skin are given for a point source and for contamination with a radionuclide β emitter. Second of all, operational quantities and protection quantities are compared. It is shown that in this case the operational quantities significantly overstate the protection quantities. For a skin contamination the ratio between operational quantities and protection quantities is 2 for a maximum β energy of 3 MeV and 90 for a maximum β energy of 150 keV. (author)

  7. Effects of insemination quantity on honey bee queen physiology.

    Directory of Open Access Journals (Sweden)

    Freddie-Jeanne Richard

    2007-10-01

    Full Text Available Mating has profound effects on the physiology and behavior of female insects, and in honey bee (Apis mellifera queens, these changes are permanent. Queens mate with multiple males during a brief period in their early adult lives, and shortly thereafter they initiate egg-laying. Furthermore, the pheromone profiles of mated queens differ from those of virgins, and these pheromones regulate many different aspects of worker behavior and colony organization. While it is clear that mating causes dramatic changes in queens, it is unclear if mating number has more subtle effects on queen physiology or queen-worker interactions; indeed, the effect of multiple matings on female insect physiology has not been broadly addressed. Because it is not possible to control the natural mating behavior of queens, we used instrumental insemination and compared queens inseminated with semen from either a single drone (single-drone inseminated, or SDI or 10 drones (multi-drone inseminated, or MDI. We used observation hives to monitor attraction of workers to SDI or MDI queens in colonies, and cage studies to monitor the attraction of workers to virgin, SDI, and MDI queen mandibular gland extracts (the main source of queen pheromone. The chemical profiles of the mandibular glands of virgin, SDI, and MDI queens were characterized using GC-MS. Finally, we measured brain expression levels in SDI and MDI queens of a gene associated with phototaxis in worker honey bees (Amfor. Here, we demonstrate for the first time that insemination quantity significantly affects mandibular gland chemical profiles, queen-worker interactions, and brain gene expression. Further research will be necessary to elucidate the mechanistic bases for these effects: insemination volume, sperm and seminal protein quantity, and genetic diversity of the sperm may all be important factors contributing to this profound change in honey bee queen physiology, queen behavior, and social interactions in the

  8. The effects of quantity and depth of processing on children's time perception.

    Science.gov (United States)

    Arlin, M

    1986-08-01

    Two experiments were conducted to investigate the effects of quantity and depth of processing on children's time perception. These experiments tested the appropriateness of two adult time-perception models (attentional and storage size) for younger ages. Children were given stimulus sets of equal time which varied by level of processing (deep/shallow) and quantity (list length). In the first experiment, 28 children in Grade 6 reproduced presentation times of various quantities of pictures under deep (living/nonliving categorization) or shallow (repeating label) conditions. Students also compared pairs of durations. In the second experiment, 128 children in Grades K, 2, 4, and 6 reproduced presentation times under similar conditions with three or six pictures and with deep or shallow processing requirements. Deep processing led to decreased estimation of time. Higher quantity led to increased estimation of time. Comparative judgments were influenced by quantity. The interaction between age and depth of processing was significant. Older children were more affected by depth differences than were younger children. Results were interpreted as supporting different aspects of each adult model as explanations of children's time perception. The processing effect supported the attentional model and the quantity effect supported the storage size model.

  9. The effect of coolant quantity on local fuel–coolant interactions in a molten pool

    International Nuclear Information System (INIS)

    Cheng, Songbai; Matsuba, Ken-ichi; Isozaki, Mikio; Kamiyama, Kenji; Suzuki, Tohru; Tobita, Yoshiharu

    2015-01-01

    Highlights: • We investigate local fuel–coolant interactions in a molten pool. • As water volume increases, limited pressurization and mechanical energy observed. • Only a part of water is evaporated and responsible for the pressurization. - Abstract: Studies on local fuel–coolant interactions (FCI) in a molten pool are important for severe accident analyses of sodium-cooled fast reactors (SFRs). Motivated by providing some evidence for understanding this interaction, in this study several experimental tests, with comparatively larger difference in coolant volumes, were conducted by delivering a given quantity of water into a simulated molten fuel pool (formed with a low-melting-point alloy). Interaction characteristics including the pressure-buildup as well as mechanical energy release and its conversion efficiency are evaluated and compared. It is found that as water quantity increases, a limited pressure-buildup and the resultant mechanical energy release are observable. The performed analyses also suggest that only a part of water is probably vaporized during local FCIs and responsible for the pressurization and mechanical energy release, especially for those cases with much larger water volumes

  10. Atmospheric dispersion models of radioactivity releases

    International Nuclear Information System (INIS)

    Oza, R.B.

    2016-01-01

    In view of the rapid industrialization in recent time, atmospheric dispersion models have become indispensible 'tools' to ensure that the effects of releases are well within the acceptable limits set by the regulatory authority. In the case of radioactive releases from the nuclear facility, though negligible in quantity and many a times not even measurable, it is required to demonstrate the compliance of these releases to the regulatory limits set by the regulatory authority by carrying out radiological impact assessment. During routine operations of nuclear facility, the releases are so low that environmental impact is usually assessed with the help of atmospheric dispersion models as it is difficult to distinguish negligible contribution of nuclear facility to relatively high natural background radiation. The accidental releases from nuclear facility, though with negligible probability of occurrence, cannot be ruled out. In such cases, the atmospheric dispersion models are of great help to emergency planners for deciding the intervention actions to minimize the consequences in public domain and also to workout strategies for the management of situation. In case of accidental conditions, the atmospheric dispersion models are also utilized for the estimation of probable quantities of radionuclides which might have got released to the atmosphere. Thus, atmospheric dispersion models are an essential tool for nuclear facility during routine operation as well as in the case of accidental conditions

  11. In vitro evaluation of extemporaneously compounded slow-release capsules containing morphine sulfate or oxycodone hydrochloride.

    Science.gov (United States)

    Glowiak, Dana L; Green, Julie L; Bowman, Bill J

    2005-01-01

    , and only one preparation showed statistically significant interbatch variation, indicating reproducible and robust formulation. Even though changing the quantity of the formulation ingredients altered the release characteristics of the slow-release capsules, which also varied from that of equivalent strength-controlled release tablets, their release profiles were similar. Further testing is needed to determine whether these diffences are clinically significant.

  12. Flavor release and perception in hard candy: influence of flavor compound-flavor solvent interactions.

    Science.gov (United States)

    Schober, Amanda L; Peterson, Devin G

    2004-05-05

    The release kinetics of l-menthol dissolved in propylene glycol (PG), Miglyol, or 1,8-cineole (two common odorless flavor solvents differing in polarity and a hydrophobic flavor compound) were monitored from a model aqueous system via atmospheric pressure chemical ionization mass spectrometry (APCI-MS). Breath analysis was also conducted via APCI-MS to monitor release of l-menthol from hard candy that used PG and Miglyol for l-menthol incorporation. The quantities of l-menthol released when dissolved in PG or Miglyol from the model aqueous system were found to be similar and overall significantly greater in comparison to when dissolved in 1,8-cineole. Analogous results were reported by the breath analysis of hard candy. The release kinetics of l-menthol from PG or Miglyol versus from 1,8-cineole were notably more rapid and higher in quantity. Results from the sensory time-intensity study also indicated that there was no perceived difference in the overall cooling intensity between the two flavor solvent delivery systems (PG and Miglyol).

  13. 48 CFR 52.217-6 - Option for Increased Quantity.

    Science.gov (United States)

    2010-10-01

    ... 48 Federal Acquisition Regulations System 2 2010-10-01 2010-10-01 false Option for Increased....217-6 Option for Increased Quantity. As prescribed in 17.208(d), insert a clause substantially the same as the following: Option for Increased Quantity (MAR 1989) The Government may increase the...

  14. 41 CFR 109-27.102 - Economic order quantity principle.

    Science.gov (United States)

    2010-07-01

    ... PROCUREMENT 27-INVENTORY MANAGEMENT 27.1-Stock Replenishment § 109-27.102 Economic order quantity principle. ... 41 Public Contracts and Property Management 3 2010-07-01 2010-07-01 false Economic order quantity principle. 109-27.102 Section 109-27.102 Public Contracts and Property Management Federal Property...

  15. 48 CFR 916.504 - Indefinite-quantity contracts.

    Science.gov (United States)

    2010-10-01

    ... indefinite-quantity, multiple award contracts to ensure that adequate consideration exists to contractually... contracts. 916.504 Section 916.504 Federal Acquisition Regulations System DEPARTMENT OF ENERGY CONTRACTING METHODS AND CONTRACT TYPES TYPES OF CONTRACTS Indefinite-Delivery Contracts 916.504 Indefinite-quantity...

  16. 30 CFR 75.322 - Harmful quantities of noxious gases.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Harmful quantities of noxious gases. 75.322... quantities of noxious gases. Concentrations of noxious or poisonous gases, other than carbon dioxide, shall... Governmental Industrial Hygienists in “Threshold Limit Values for Substance in Workroom Air” (1972). Detectors...

  17. Symbols and definitions of quantities and units in isotope stoichiometry

    International Nuclear Information System (INIS)

    Junghans, P.; Krumbiegel, P.; Faust, H.

    1982-01-01

    On the basis of the International System of Units and recent recommendations of the IUPAC on 'Symbols and Terminology for Physicochemical Quantities and Units' a system is proposed of uniform and unambiguous symbols and definitions of quantities and units used in the isotope dilution technique. The close relationship between isotope stoichiometry and common stoichiometry is demonstrated. (author)

  18. 19 CFR 144.33 - Minimum quantities to be withdrawn.

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 2 2010-04-01 2010-04-01 false Minimum quantities to be withdrawn. 144.33 Section 144.33 Customs Duties U.S. CUSTOMS AND BORDER PROTECTION, DEPARTMENT OF HOMELAND SECURITY; DEPARTMENT... Warehouse § 144.33 Minimum quantities to be withdrawn. Unless by special authority of the Commissioner of...

  19. 21 CFR 1314.20 - Restrictions on sales quantity.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 9 2010-04-01 2010-04-01 false Restrictions on sales quantity. 1314.20 Section 1314.20 Food and Drugs DRUG ENFORCEMENT ADMINISTRATION, DEPARTMENT OF JUSTICE RETAIL SALE OF SCHEDULED LISTED CHEMICAL PRODUCTS Sales by Regulated Sellers § 1314.20 Restrictions on sales quantity. (a) Without...

  20. Quantifying cannabis: A field study of marijuana quantity estimation.

    Science.gov (United States)

    Prince, Mark A; Conner, Bradley T; Pearson, Matthew R

    2018-05-17

    The assessment of marijuana use quantity poses unique challenges. These challenges have limited research efforts on quantity assessments. However, quantity estimates are critical to detecting associations between marijuana use and outcomes. We examined accuracy of marijuana users' estimations of quantities of marijuana they prepared to ingest and predictors of both how much was prepared for a single dose and the degree of (in)accuracy of participants' estimates. We recruited a sample of 128 regular-to-heavy marijuana users for a field study wherein they prepared and estimated quantities of marijuana flower in a joint or a bowl as well as marijuana concentrate using a dab tool. The vast majority of participants overestimated the quantity of marijuana that they used in their preparations. We failed to find robust predictors of estimation accuracy. Self-reported quantity estimates are inaccurate, which has implications for studying the link between quantity and marijuana use outcomes. (PsycINFO Database Record (c) 2018 APA, all rights reserved).

  1. Significant Radionuclides Determination

    Energy Technology Data Exchange (ETDEWEB)

    Jo A. Ziegler

    2001-07-31

    The purpose of this calculation is to identify radionuclides that are significant to offsite doses from potential preclosure events for spent nuclear fuel (SNF) and high-level radioactive waste expected to be received at the potential Monitored Geologic Repository (MGR). In this calculation, high-level radioactive waste is included in references to DOE SNF. A previous document, ''DOE SNF DBE Offsite Dose Calculations'' (CRWMS M&O 1999b), calculated the source terms and offsite doses for Department of Energy (DOE) and Naval SNF for use in design basis event analyses. This calculation reproduces only DOE SNF work (i.e., no naval SNF work is included in this calculation) created in ''DOE SNF DBE Offsite Dose Calculations'' and expands the calculation to include DOE SNF expected to produce a high dose consequence (even though the quantity of the SNF is expected to be small) and SNF owned by commercial nuclear power producers. The calculation does not address any specific off-normal/DBE event scenarios for receiving, handling, or packaging of SNF. The results of this calculation are developed for comparative analysis to establish the important radionuclides and do not represent the final source terms to be used for license application. This calculation will be used as input to preclosure safety analyses and is performed in accordance with procedure AP-3.12Q, ''Calculations'', and is subject to the requirements of DOE/RW-0333P, ''Quality Assurance Requirements and Description'' (DOE 2000) as determined by the activity evaluation contained in ''Technical Work Plan for: Preclosure Safety Analysis, TWP-MGR-SE-000010'' (CRWMS M&O 2000b) in accordance with procedure AP-2.21Q, ''Quality Determinations and Planning for Scientific, Engineering, and Regulatory Compliance Activities''.

  2. Organizational citizenship behavior and the quantity and quality of work group performance.

    Science.gov (United States)

    Podsakoff, P M; Ahearne, M; MacKenzie, S B

    1997-04-01

    Despite the widespread interest in the topic of organizational citizenship behaviors (OCBs), little empirical research has tested the fundamental assumption that these forms of behavior improve the effectiveness of work groups or organizations in which they are exhibited. In the present study, the effects of OCBs on the quantity and quality of the performance of 218 people working in 40 machine crews in a paper mill located in the Northeastern United States were examined. The results indicate that helping behavior and sportsmanship had significant effects on performance quantity and that helping behavior had a significant impact on performance quality. However, civic virtue had no effect on either performance measure.

  3. Association Between Work–Family Conflict and Smoking Quantity Among Daily Smokers

    Science.gov (United States)

    2013-01-01

    Introduction: Recent work demonstrated a direct relation between work–family conflict and likelihood of smoking. This study furthered this area of research by (a) testing the association between work–family conflict and smoking quantity and (b) testing demographic, workplace, and home factors as moderators of this relation. Methods: Participants (N = 423) were daily smokers from a Midwestern community-based sample. Ordinal regression analysis tested work-to-home and home-to-work conflict as predictors (after controlling for demographic characteristics, home factors, and workplace factors) of smoking quantity. Additionally, we tested whether the demographic, home, and workplace factors moderated the effects of work-to-home conflict and home-to-work conflict on smoking quantity. Results: Males (OR = 8.81, p = .005), older participants (OR = 1.09, p = .012), those with less educational attainment (OR = 1.87, p = .001), those who reported lower levels of workplace smoking restrictions (OR = 0.87, p = .019), and those who reported higher levels of work-to-home conflict (OR = 1.39, p = .026) smoked more cigarettes per day. There was no significant main effect of home-to-work conflict on smoking quantity (OR = 1.46, p = .099). A significant interaction (OR = 0.55, p = .043) revealed that home-to-work conflict was associated with smoking quantity for females but not for males. Conclusions: After controlling for demographic characteristics and potential confounders, work-to-home conflict had a negative impact on smoking quantity for all participants, and home-to-work conflict was associated with smoking quantity for women. Workplace wellness programs to reduce smoking among employees should take into account the direction of conflict and how the effect of the conflict on smoking behavior may vary based on other factors. PMID:23709611

  4. Association between work-family conflict and smoking quantity among daily smokers.

    Science.gov (United States)

    Macy, Jonathan T; Chassin, Laurie; Presson, Clark C

    2013-11-01

    Recent work demonstrated a direct relation between work-family conflict and likelihood of smoking. This study furthered this area of research by (a) testing the association between work-family conflict and smoking quantity and (b) testing demographic, workplace, and home factors as moderators of this relation. Participants (N = 423) were daily smokers from a Midwestern community-based sample. Ordinal regression analysis tested work-to-home and home-to-work conflict as predictors (after controlling for demographic characteristics, home factors, and workplace factors) of smoking quantity. Additionally, we tested whether the demographic, home, and workplace factors moderated the effects of work-to-home conflict and home-to-work conflict on smoking quantity. Males (OR = 8.81, p = .005), older participants (OR = 1.09, p = .012), those with less educational attainment (OR = 1.87, p = .001), those who reported lower levels of workplace smoking restrictions (OR = 0.87, p = .019), and those who reported higher levels of work-to-home conflict (OR = 1.39, p = .026) smoked more cigarettes per day. There was no significant main effect of home-to-work conflict on smoking quantity (OR = 1.46, p = .099). A significant interaction (OR = 0.55, p = .043) revealed that home-to-work conflict was associated with smoking quantity for females but not for males. After controlling for demographic characteristics and potential confounders, work-to-home conflict had a negative impact on smoking quantity for all participants, and home-to-work conflict was associated with smoking quantity for women. Workplace wellness programs to reduce smoking among employees should take into account the direction of conflict and how the effect of the conflict on smoking behavior may vary based on other factors.

  5. The behavior, quantity, and location of undissolved gas in Tank 241-SY-101

    Energy Technology Data Exchange (ETDEWEB)

    Brewster, M.E.; Gallagher, N.B.; Hudson, J.D.; Stewart, C.W.

    1995-10-01

    Mitigation of episodic flammable gas releases from Hanford Waste Tank 241-SY-101 was accomplished in July 1993 with the installation of a mixer pump that prevents gas retention. But is has not been possible until recently to measure the effects of mixing on the waste or how much gas remains and where it is located. Direct measurements of the void fraction and rheology of the mixed waste by the void fraction instrument (VFI) and ball rheometer along with previous data provide estimates of the location, quantity, and behavior of undissolved gas in the tank. This report documents the compilation and integration of the information that enables this understanding.

  6. Toxic releases from power plants

    International Nuclear Information System (INIS)

    Rubin, E.S.

    1999-01-01

    Beginning in 1998, electric power plants burning coal or oil must estimate and report their annual releases of toxic chemicals listed in the Toxics Release Inventory (TRI) published by the US Environmental Protection Agency (EPA). This paper identifies the toxic chemicals of greatest significance for the electric utility sector and develops quantitative estimates of the toxic releases reportable to the TRI for a representative coal-fired power plant. Key factors affecting the magnitude and types of toxic releases for individual power plants also are discussed. A national projection suggests that the magnitude of electric utility industry releases will surpass those of the manufacturing industries which current report to the TRI. Risk communication activities at the community level will be essential to interpret and provide context for the new TRI results

  7. The Plinius/Colima CA-U3 test on fission-product aerosol release over a VVER-type corium pool

    International Nuclear Information System (INIS)

    Journeau, Ch.; Piluso, P.; Correggio, P.; Godin-Jacqmin, L.

    2007-01-01

    In a hypothetical case of severe accident in a PWR type VVER-440, a complex corium pool could be formed and fission products could be released. In order to study aerosols release in terms of mechanisms, kinetics, nature or quantity, and to better precise the source term of VVER-440, a series of experiments have been performed in the Colima facility and the test Colima CA-U3 has been successfully performed thanks to technological modifications to melt a prototypical corium at 2760 C degrees. Specific instrumentation has allowed us to follow the evolution of the corium melt and the release, transport and deposition of the fission products. The main conclusions are: -) there is a large release of Cr, Te, Sr, Pr and Rh (>95%w), -) there is a significant release of Fe (50%w), -) there is a small release of Ba, Ce, La, Nb, Nd and Y (<90%w), -) there is a very small release of U in proportion (<5%w) but it is one of the major released species in mass, and -) there is no release of Zr. The Colima experimental results are consistent with previous experiments on irradiated fuels except for Ba, Fe and U releases. (A.C.)

  8. Concept of ICRU's operational quantity and its application

    International Nuclear Information System (INIS)

    Murakami, Hiroyuki

    1995-01-01

    The operational quantity which was introduced in the ICRU report 39 published in 1985 was shocking rather than fresh for the author. The report was translated into Japanese, but at the beginning, the contents were not able to be understood. Thereafter, the measurement of ICRU sphere dose equivalent was introduced in a national law. But it is feared that the understanding of this operational quantity is limited to specialist level, and is not by men of practical works. The meaning of ''operational'' must be that workers measure and obtain dose on the spot for the radiation protection for themselves. The principles used when ICRU considered the new practical measured quantity are shown. In the definition of operational quantity in area monitoring, two concepts of expanded and aligned connect real measurement with the operational quantity. The problems of measuring individual dose equivalent are discussed. As to the reality of applying the operational quantity, the fundamentals of the calibration of measuring instruments, the investigation of the operational quantity in relation to measuring instruments and measurement mode, and the relation of area monitoring and individual monitoring are described. (K.I.)

  9. Influence of Cattle Trails on Runoff Quantity and Quality.

    Science.gov (United States)

    Miller, Jim J; Curtis, Tony; Chanasyk, David S; Willms, Walter D

    2017-03-01

    Cattle trails in grazed pastures close to rivers may adversely affect surface water quality of the adjacent river by directing runoff to it. The objective of this 3-yr study (2013-2015) in southern Alberta, Canada, was to determine if cattle trails significantly increased the risk of runoff and contaminants (sediment, nutrients) compared with the adjacent grazed pasture (control). A portable rainfall simulator was used to generate artificial rainfall (140 mm h) and runoff. The runoff properties measured were time to runoff and initial abstraction (infiltration), total runoff depth and average runoff rates, as well as concentrations and mass loads of sediment, N, and P fractions. Cattle trails significantly ( ≤ 0.10) decreased time to runoff and initial abstraction (26-32%) in the 2 yr measured and increased total runoff depth, runoff coefficients, and average runoff rates (21-51%) in 2 of 3 yr. Concentrations of sediment, N, and P fractions in runoff were not significantly greater for cattle trails than for control areas. However, mass loads of total suspended solids (57-85% increase), NH-N (31-90%), and dissolved reactive P (DRP) (30-92%) were significantly greater because of increased runoff volumes. Overall, runoff quantity and loads of sediment, NH-N, and DRP were greater for cattle trails compared with the adjacent grazed pasture, and hydrologic connection with cattle-access sites on the riverbank suggests that this could adversely affect water quality in the adjacent river. Extrapolation of the study results should be tempered by the specific conditions represented by this rainfall simulation study. Copyright © by the American Society of Agronomy, Crop Science Society of America, and Soil Science Society of America, Inc.

  10. Conceptual Model of Quantities, Units, Dimensions, and Values

    Science.gov (United States)

    Rouquette, Nicolas F.; DeKoenig, Hans-Peter; Burkhart, Roger; Espinoza, Huascar

    2011-01-01

    JPL collaborated with experts from industry and other organizations to develop a conceptual model of quantities, units, dimensions, and values based on the current work of the ISO 80000 committee revising the International System of Units & Quantities based on the International Vocabulary of Metrology (VIM). By providing support for ISO 80000 in SysML via the International Vocabulary of Metrology (VIM), this conceptual model provides, for the first time, a standard-based approach for addressing issues of unit coherence and dimensional analysis into the practice of systems engineering with SysML-based tools. This conceptual model provides support for two kinds of analyses specified in the International Vocabulary of Metrology (VIM): coherence of units as well as of systems of units, and dimension analysis of systems of quantities. To provide a solid and stable foundation, the model for defining quantities, units, dimensions, and values in SysML is explicitly based on the concepts defined in VIM. At the same time, the model library is designed in such a way that extensions to the ISQ (International System of Quantities) and SI Units (Systeme International d Unites) can be represented, as well as any alternative systems of quantities and units. The model library can be used to support SysML user models in various ways. A simple approach is to define and document libraries of reusable systems of units and quantities for reuse across multiple projects, and to link units and quantity kinds from these libraries to Unit and QuantityKind stereotypes defined in SysML user models.

  11. News/Press Releases

    Data.gov (United States)

    Office of Personnel Management — A press release, news release, media release, press statement is written communication directed at members of the news media for the purpose of announcing programs...

  12. Investigators find hundreds of intentional nuclear releases

    International Nuclear Information System (INIS)

    Lobsenz, G.

    1994-01-01

    Investigators with the federal Advisory Committee on Human Radiation Experiments have said that the category of intentional releases is now known to be larger, in variety and quantity, than the 13 releases identified prior to the committee's formation in January 1994 by President Clinton. The committee is now aware of hundreds of additional intentional releases. In addition to the intentional releases, the committee said it had compiled documents on 400 biomedical experiments involving radiation prior to 1975, and had at least fragmentary evidence of more than 1,000 more. The committee also discovered a top secret 1953 Defense Department policy statement on human experimentation that was based on the World War II-era Nuremberg Code. The committee said it was looking into how or whether the policy was implemented. The committee is expected to issue a final report, including recommendations on possible compensation for victims by April 1995

  13. Layer-Mean Quantities, Local Conservation Laws, and Vorticity

    International Nuclear Information System (INIS)

    Camassa, R.; Levermore, C.D.

    1997-01-01

    We derive local conservation laws for layer-mean quantities in two general settings. When applied to Euler flows, the first of these settings yields well-known local conservation laws for quantities averaged between material surfaces. The second, however, leads to new local conservation laws for quantities involving the vorticity that are averaged between arbitrary surfaces. These produce the crucial vorticity conservation laws in shallow water models that admit nonhydrostatic and noncolumnar motion. Moreover, they seem to lie outside the Hamiltonian paradigm of fluid dynamics. The formalism generalizes to skew-symmetric matrix fields; applications to electromagnetism are suggested. copyright 1997 The American Physical Society

  14. New quantities in radiation protection and conversion coefficients

    International Nuclear Information System (INIS)

    1986-01-01

    Four new quantities have been proposed by the ICRP for use in radiation protection from external sources, i.e. the ambient dose equivalent, the directional dose equivalent, the individual dose equivalent (penetrating), and the individual dose equivalent (superficial). These quantities are briefly described together with two new concepts of expanded and aligned fields. The BCRU recommends that these quantities should be adopted for use in the UK together with conversion coefficients when re-calibrating existing instruments, reporting the results of measurements and designing instruments. (UK)

  15. Experience of iodine, caesium and noble gas release from AGR failures

    International Nuclear Information System (INIS)

    Chapman, C.J.; Harris, A.M.; Phillips, M.E.

    1985-01-01

    In the event of a fuel failure in an Advanced Gas Cooled Reactor (AGR), the quantity of fission products available for release to the environment is determined by the transport of fission products in the UO 2 fuel, by the possible retention of fission products in the fuel can interspace and by the deposition of fission products on gas circuit surfaces ('plate-out'). The fission products of principal radiological concern are radioactive caesium (Cs-137 and Cs-134) and iodine (principally I-131). Results are summarised of a number of experiments which were designed to study the release of these fission products from individual fuel failures in the prototype AGR at Windscale. Results are also presented of fission product release from failures in commercial AGRs. Comparisons of measured releases of caesium and iodine relative to the release of the noble gas fission products show that, for some fuel failures, there is a significant retention of caesium and iodine within the fuel can interspace. Under normal conditions circuit deposition reduces caesium and iodine gas concentrations by several orders of magnitude. Differing release behaviour of caesium and iodine from the failures is examined together with subsequent deposition within the sampling equipment. These observations are important factors which must be considered in developing an understanding of the mechanisms involved in circuit deposition. (author)

  16. An analysis of the additional fission product release phenomena

    International Nuclear Information System (INIS)

    Takeda, Tsuneo; Nagai, Hitoshi

    1978-09-01

    The additional fission product release behavior through a defect hole on the cladding of fuel rods has been studied qualitatively with a computer program CODAC-ARFP. The additional fission product release phenomena are described as qualitative evaluation. The additional fission product release behavior in coolant temperature and pressure fluctuations and in reactor start-up and shut-down depends on coolant water flow behavior into and from the free space of fuel rods through a defect hole. Based on the results of evaluations, the experimental results with an inpile water loop OWL-1 are described in detail. The estimation methods of fission product quantity in the free space and fission product release ratio (quantity released into the coolant/quantity in the free space before beginning of release) are necessary for analysis of the fission product release behavior; the estimation method of water flow through a defect hole is also necessary. In development of the above estimation methods, outpile and capsule experiments supporting the additional fission product release experiments are required. (author)

  17. Cetirizine release from cyclodextrin formulated compressed chewing gum

    DEFF Research Database (Denmark)

    Stojanov, Mladen; Larsen, Kim Lambertsen

    2012-01-01

    release patterns, but with variations in the total amount released. Chewing gum formulated with cetirizine alone, demonstrated a release of 75% after 8 min of chewing. The presence of CDs resulted in increased cetirizine release. The analysis of variance (ANOVA) demonstrated that parameters with the most...... the statistical analysis (ANOVA) demonstrated significance in the release (P

  18. WEB TECHNOLOGIES USED TO FORECAST FUTURE WASTE QUANTITIES

    Directory of Open Access Journals (Sweden)

    Valeriu LUPU

    2014-06-01

    Full Text Available In this article the authors propose a modality of prognosis of the quantities of waste generated in a certain period. The proposition was finalized by achieving a model of prognosis present on a site hosted by a Web server. The software solve the problem for the general case, depending on the input data after analysis. After analyzing input data sets are used with one, two or three components (trend, seasonality and residual variable. According to the input data the adjustment model regarding the description of the analyzed phenomenon (additive and multiplying is chosen. If the chronogram of the analyzed phenomenon indicates an oscillating evolution, of sinusoidal nature, the additive model (+ is chosen, otherwise the multiplying model (  is chosen. The seasonal component is estimated and the deseasonalized chronological series is determined. The seasonality is determined by: the procedure of arithmetical means, the procedure of moving averages and the procedure of analytical tendency. The adjustment function is specified regarding the tendency of the phenomenon and its parameters are estimated. The significance of the adjustment function is verified specifying the significance threshold with which it may be accepted as significant. The estimation of the parameters of the adjustment function is made on the basis of the application of the method of least squares. The values of the phenomenon on two or three trimesters/ months are estimated for the processed data (by using time series with two or three steps ahead. Several types of waste specified by the value of the meter for waste from the database may be accepted. The model proposed makes decisions and justifies if the data prognosticated is accepted or not. All information from the input data to the final data is stored in a MySQL database.

  19. HARAD, Decay Isotope Concentration from Atmospheric Noble-Gas Release

    International Nuclear Information System (INIS)

    Moore, R.E.

    1986-01-01

    1 - Description of problem or function: HARAD calculates concentrations of radioactive daughters in air following the atmospheric release of a parent radionuclide for a variety of release heights and meteorological conditions. It can be applied most profitably to the assessment of doses to man from the noble gases such as Rn-222, Rn-220, and Xe and Kr isotopes. These gases can produce significant quantities of short-lived particulate daughters in an airborne plume, which are the major contributors to dose. The simultaneous processes of radioactive decay, buildup and environmental loss due to wet and dry deposition on ground surfaces are calculated for a daughter chain in an airborne plume as it is dispersed downwind from a point of release of a parent. 2 - Method of solution: The code evaluates the analytic solution to the set of coupled first order differential equations describing time variation of the concentration of a chain of radionuclides. The analytic solutions assume that the coefficient describing the fractional rate of dry deposition is constant with time. To account for the variation the time coordinate is automatically divided into intervals and a set of average values are used. 3 - Restrictions on the complexity of the problem: - The maximum length of decay chain is 10 nuclides; calculations can be made at a maximum of 24 downwind distances

  20. Quality and quantity of construction and demolition waste in Tehran.

    Science.gov (United States)

    Asgari, Alireza; Ghorbanian, Tahereh; Yousefi, Nader; Dadashzadeh, Dariush; Khalili, Fatemeh; Bagheri, Amin; Raei, Mehdi; Mahvi, Amir Hossein

    2017-01-01

    In recent years the generation rate of construction and demolition waste (C&D) has significantly augmented. The aim of this study was to assessed the quality and quantity of construction and demolition waste in Tehran (capital of Iran). Questionnaire methods were used for estimating the amount of generated C&D wastes national statistical data and typical waste generation data. In order to defining the composition of C&D waste, trucks were randomly selected and their wastes were separated and weighted. According to obtained results, about 82,646,051 m 3 of C&D waste (average 16,529,210 m 3 per year) were generated during 2011 to 2016 which only about 26% of them has been recycled. Mixing sand and cement, concrete, broken bricks and soil have the highest amount of the composition of C&D waste in Tehran that was 30, 19, 18 and 11%, respectively. Based on the results, about 2,784,158 t of the waste will generate in 2025 and this is approximately 122% higher than wastes generate in 2016. Based on MAPSA's data, 360 teams of personnel cruise and control the illegal disposals, but due to the expansion of Tehran this number of teams is inadequate and can't be effective in controlling the situation. In general, the overall condition of C&D waste management in Tehran seems undesirable and needs to be updated based on the experience of successful countries in this field.

  1. A note on the expectation and deviation of physical quantities

    International Nuclear Information System (INIS)

    Nagasawa, Masao

    2009-01-01

    By using the function representation of self-adjoint operators, the expectation and variance of physical quantities (self-adjoint operators) are defined, and it is shown that the so-called uncertainty principle does not hold.

  2. The ICRU dose equivalence quantities in radiation protection

    International Nuclear Information System (INIS)

    Grimbergen, T.W.M.

    1990-09-01

    The definitions and application of the new ICRU radiation protection quantities have been reviewed and studied in literature. Special emphasis was laid on the consequences of the use of the new quantities by personnel dosimetry services, and on the consequences of the use of the new quantities during an intercomparison programme for dosimetry services. The study shows that the recommendations of the ICRU are not yet complete and not fully realizable. This means that the dosimetry services always have to make certain approximations, when they use the new quantities. In literature, several approaches have been proposed. The feasibility of an approach depends on the characteristics of the dosimeters used. The use of different approaches by the dosimetry services is thought to be of possible influence on the results of an intercomparison programme. (author). 42 refs.; 3 figs.; 1 tab

  3. Safeguards Implementation Guide for States with Small Quantities Protocols

    International Nuclear Information System (INIS)

    2013-01-01

    The International Atomic Energy Agency (IAEA) works to enhance the contribution of nuclear energy for peace and prosperity around the world, while helping to ensure that nuclear material is not diverted to nuclear weapons or other nuclear explosive devices. In implementing safeguards, the IAEA plays an instrumental independent verification role, providing credible assurances that States' safeguards commitments are being respected. Most of the world's non-nuclear-weapon States (NNWSs) have concluded comprehensive safeguards agreements (CSAs) with the IAEA, pursuant to the Treaty on the Non- Proliferation of Nuclear Weapons (NPT). The IAEA and States are required to cooperate in the implementation of such agreements. Effective cooperation demonstrates a State's commitment to the peaceful use of nuclear energy and furthers the State's national interests by reducing the risk of unauthorized use of nuclear material. Over 100 NNWSs party to the NPT have very limited quantities of nuclear material and have concluded protocols to their CSAs which hold in abeyance many procedures in Part II of a CSA. These protocols are referred to as 'small quantities protocols' or 'SQPs' and remain in effect as long as the State meets certain eligibility criteria. The purpose of an SQP is to reduce the burden of safeguards implementation for States with little or no nuclear activities, while retaining the integrity of the safeguards system. States with SQPs have very important obligations they must fulfil under their CSAs. In 1997, as part of the IAEA's efforts to strengthen its safeguards system, the Model Additional Protocol to the Agreement(s) between State(s) and the International Atomic Energy Agency for the Application of Safeguards was developed to provide the IAEA with broader access to information and locations, thus significantly increasing the IAEA's ability to provide assurance of the absence of undeclared nuclear material and activities in States. Many States with SQPs have

  4. Quantity versus Quality: A New Approach to Examine the Relationship between Technology Use and Student Outcomes

    Science.gov (United States)

    Lei, Jing

    2010-01-01

    The author argues that to examine the relationship between technology use and student outcomes, the quality of technology use--how, and what, technology is used--is a more significant factor than the quantity of technology use--how much technology is used. This argument was exemplified by an empirical study that used both angles to examine the…

  5. Import and export of small quantities of nuclear materials

    International Nuclear Information System (INIS)

    Grenier, M.

    1986-06-01

    Administrative procedures for import export of nuclear materials are specific for each country. In France regulations are reviewed for small quantities, lower threshold, in some cases, allows a simplified procedure, however thresholds are not the same in the different texts (and for one of them, concerning proliferation, is zero). It is obvious that regulations are necessary even for small quantities but national and international threshold should be harmonized [fr

  6. Complexity in an Unexpected Place: Quantities in Selected Acquisition Reports

    Science.gov (United States)

    2017-12-01

    by the Army Acquisition Executive contains the following language . As a recently delegated Acquisition Category IC program, the AH-64E Apache...Complexity in an Unexpected Place: Quantities in Selected Acquisition Reports Gregory A. Davis, Project Leader Margaret L. Giles David M. Tate I...F E N S E A N A L Y S E S IDA Paper P-8490 Complexity in an Unexpected Place: Quantities in Selected Acquisition Reports Gregory A. Davis

  7. Charaterisation of function spaces via mollification; fractal quantities for distributions

    Directory of Open Access Journals (Sweden)

    Hans Triebel

    2003-01-01

    Full Text Available The aim of this paper is twofold. First we characterise elements f belonging to the Besov spaces Bpqs(ℝn with s∈ℝ,  0quantities for distributions generalising well-known corresponding quantities for Radon measures.

  8. Information quantity in a pixel of digital image

    OpenAIRE

    Kharinov, M.

    2014-01-01

    The paper is devoted to the problem of integer-valued estimating of information quantity in a pixel of digital image. The definition of an integer estimation of information quantity based on constructing of the certain binary hierarchy of pixel clusters is proposed. The methods for constructing hierarchies of clusters and generating of hierarchical sequences of image approximations that minimally differ from the image by a standard deviation are developed. Experimental results on integer-valu...

  9. Uncertainty analysis of thermal quantities measurement in a centrifugal compressor

    Science.gov (United States)

    Hurda, Lukáš; Matas, Richard

    2017-09-01

    Compressor performance characteristics evaluation process based on the measurement of pressure, temperature and other quantities is examined to find uncertainties for directly measured and derived quantities. CFD is used as a tool to quantify the influences of different sources of uncertainty of measurements for single- and multi-thermocouple total temperature probes. The heat conduction through the body of the thermocouple probe and the heat-up of the air in the intake piping are the main phenomena of interest.

  10. Testing quantity theory of money for the Turkish economy

    OpenAIRE

    Levent, Korap

    2007-01-01

    In this paper, it is tried to test the main assumptions of the Quantity Theory of Money for the Turkish economy. Using some contemporaneous estimation techniques to examine the long-run stationary economic relationships on which the quantity theory is constructed, it is found that stationary characteristics of the velocitities of narrowly and broadly defined monetary aggregates cannot be rejected. However, monetary aggregates seem to be endogenous for the long-run evoluation of prices and rea...

  11. Energy Drinks and Binge Drinking Predict College Students' Sleep Quantity, Quality, and Tiredness.

    Science.gov (United States)

    Patrick, Megan E; Griffin, Jamie; Huntley, Edward D; Maggs, Jennifer L

    2018-01-01

    This study examines whether energy drink use and binge drinking predict sleep quantity, sleep quality, and next-day tiredness among college students. Web-based daily data on substance use and sleep were collected across four semesters in 2009 and 2010 from 667 individuals for up to 56 days each, yielding information on 25,616 person-days. Controlling for average levels of energy drink use and binge drinking (i.e., 4+ drinks for women, 5+ drinks for men), on days when students consumed energy drinks, they reported lower sleep quantity and quality that night, and greater next-day tiredness, compared to days they did not use energy drinks. Similarly, on days when students binge drank, they reported lower sleep quantity and quality that night, and greater next-day tiredness, compared to days they did not binge drink. There was no significant interaction effect between binge drinking and energy drink use on the outcomes.

  12. Nuclear trafficking latest statistics released

    International Nuclear Information System (INIS)

    2005-01-01

    Full text: Countries reported 121 incidents to the IAEA in 2004 of illicit trafficking and other unauthorized activities involving nuclear and other radioactive materials, newly released statistics from the Agency's Illicit Trafficking Database (ITDB) show. The ITDB report also shows that one incident was reported since 2003 that involved fissile material - highly enriched uranium (HEU) or plutonium - that is needed to make a nuclear weapon. It occurred in June 2003 when an individual was arrested in possession of 170 grams of HEU, attempting to illegally transport it across the border. During the two-year period 2003-2004, the number of incidents reported by States substantially increased compared with previous years. 'Improved reporting may in part account for it,' the report said. 'The majority of the incidents reported in 2003-2004 showed no evidence of criminal activity.' The Past Twelve Years: 1993 - 2004 Nuclear Weapons Grade Material. Since the database started in 1993, there have been eighteen confirmed incidents involving trafficking in HEU and plutonium. A few of these incidents involved seizures of kilogram quantities of weapons-usable nuclear material but most involved very small quantities. In some of the cases the seized material was allegedly a sample of larger quantities available for illegal sale or at risk of theft. More than two dozens incidents involved trace amounts of plutonium sources. Table can be viewed: Incidents involving HEU and Pu confirmed to the ITDB (1993-2004). Nuclear Materials. In the past twelve years, 220 incidents involved nuclear materials. The majority of confirmed cases with nuclear materials involved low-grade nuclear materials, mostly in the form of reactor fuel pellets, and natural uranium, depleted uranium and thorium. While the quantities of these materials have been rather small to be significant for nuclear proliferation or use in a terrorist nuclear explosive device, these cases are indicative of gaps in the control

  13. PWR-GALE, Radioactive Gaseous Release and Liquid Release from PWR

    International Nuclear Information System (INIS)

    Chandrasekaran, T.; Lee, J.Y.; Willis, C.A.

    1988-01-01

    1 - Description of program or function: The PWR-GALE (Boiling Water Reactor Gaseous and Liquid Effluents) Code is a computerized mathematical model for calculating the release of radioactive material in gaseous and liquid effluents from pressurized water reactors (PWRs). The calculations are based on data generated from operating reactors, field tests, laboratory tests, and plant-specific design considerations incorporated to reduce the quantity of radioactive materials that may be released to the environment. 2 - Method of solution: GALE calculates expected releases based on 1) standardized coolant activities derived from ANS Standards 18.1 Working Group recommendations, 2) release and transport mechanisms that result in the appearance of radioactive material in liquid and gaseous waste streams, 3) plant-specific design features used to reduce the quantities of radioactive materials ultimately released to the environs, and 4) information received on the operation of nuclear power plants. 3 - Restrictions on the complexity of the problem: The liquid release portion of GALE uses subroutines taken from the ORIGEN (CCC-217) to calculate radionuclide buildup and decay during collection, processing, and storage of liquid radwaste. Memory requirements for this part of the program are determined by the large nuclear data base accessed by these subroutines

  14. Processing ordinality and quantity: the case of developmental dyscalculia.

    Directory of Open Access Journals (Sweden)

    Orly Rubinsten

    Full Text Available In contrast to quantity processing, up to date, the nature of ordinality has received little attention from researchers despite the fact that both quantity and ordinality are embodied in numerical information. Here we ask if there are two separate core systems that lie at the foundations of numerical cognition: (1 the traditionally and well accepted numerical magnitude system but also (2 core system for representing ordinal information. We report two novel experiments of ordinal processing that explored the relation between ordinal and numerical information processing in typically developing adults and adults with developmental dyscalculia (DD. Participants made "ordered" or "non-ordered" judgments about 3 groups of dots (non-symbolic numerical stimuli; in Experiment 1 and 3 numbers (symbolic task: Experiment 2. In contrast to previous findings and arguments about quantity deficit in DD participants, when quantity and ordinality are dissociated (as in the current tasks, DD participants exhibited a normal ratio effect in the non-symbolic ordinal task. They did not show, however, the ordinality effect. Ordinality effect in DD appeared only when area and density were randomized, but only in the descending direction. In the symbolic task, the ordinality effect was modulated by ratio and direction in both groups. These findings suggest that there might be two separate cognitive representations of ordinal and quantity information and that linguistic knowledge may facilitate estimation of ordinal information.

  15. Processing ordinality and quantity: the case of developmental dyscalculia.

    Science.gov (United States)

    Rubinsten, Orly; Sury, Dana

    2011-01-01

    In contrast to quantity processing, up to date, the nature of ordinality has received little attention from researchers despite the fact that both quantity and ordinality are embodied in numerical information. Here we ask if there are two separate core systems that lie at the foundations of numerical cognition: (1) the traditionally and well accepted numerical magnitude system but also (2) core system for representing ordinal information. We report two novel experiments of ordinal processing that explored the relation between ordinal and numerical information processing in typically developing adults and adults with developmental dyscalculia (DD). Participants made "ordered" or "non-ordered" judgments about 3 groups of dots (non-symbolic numerical stimuli; in Experiment 1) and 3 numbers (symbolic task: Experiment 2). In contrast to previous findings and arguments about quantity deficit in DD participants, when quantity and ordinality are dissociated (as in the current tasks), DD participants exhibited a normal ratio effect in the non-symbolic ordinal task. They did not show, however, the ordinality effect. Ordinality effect in DD appeared only when area and density were randomized, but only in the descending direction. In the symbolic task, the ordinality effect was modulated by ratio and direction in both groups. These findings suggest that there might be two separate cognitive representations of ordinal and quantity information and that linguistic knowledge may facilitate estimation of ordinal information.

  16. Quantities of natural gas transported in January-December 2009

    International Nuclear Information System (INIS)

    2010-01-01

    GRTgaz is a European leader in natural gas transmission, a world expert in gas transmission networks and systems, and an operator firmly committed to the energy transition. It owns and operates the gas transmission network throughout most of France and it manages the transmission network in Germany, thereby helping to ensure correct operation of the French and European gas market. It contributes to the energy security of regional supply systems and performs a public service mission to ensure the continuity of consumer supply. This document presents the monthly key figures of GRTgaz activity in 2009: Total quantities transmitted by GRTgaz (Inputs to the GRTgaz network/Outputs from the GRTgaz network); Maximum and minimum daily flow (Daily quantities transported, Daily consumption, Daily inputs excluding storage); Quantities exchanged on the wholesale market; Consumption on the GRTgaz Network (gross monthly consumption and Average monthly temperatures)

  17. Quantities of natural gas transported in August-December 2007

    International Nuclear Information System (INIS)

    2008-01-01

    GRTgaz is a European leader in natural gas transmission, a world expert in gas transmission networks and systems, and an operator firmly committed to the energy transition. It owns and operates the gas transmission network throughout most of France and it manages the transmission network in Germany, thereby helping to ensure correct operation of the French and European gas market. It contributes to the energy security of regional supply systems and performs a public service mission to ensure the continuity of consumer supply. This document presents the available monthly key figures of GRTgaz activity from August to December 2007: Total quantities transmitted by GRTgaz (Inputs to the GRTgaz network/Outputs from the GRTgaz network); Maximum and minimum daily flow (Daily quantities transported, Daily consumption, Daily inputs excluding storage); Quantities exchanged on the wholesale market; Consumption on the GRTgaz Network (gross monthly consumption and Average monthly temperatures)

  18. BIRTHDAY CAKE ACTIVITY STRUCTURED ARRANGEMENT FOR HELPING CHILDREN DETERMINING QUANTITIES

    Directory of Open Access Journals (Sweden)

    Neni Mariana

    2010-07-01

    Full Text Available Few researches have been concerned about relation between children’s spatialthinking and number sense. Narrowing for this small research, we focused onone component of spatial thinking, that is structuring objects, and onecomponent of number senses, that is cardinality by determining quantities. Thisstudy focused on a design research that was conducted in Indonesia in which weinvestigated pre-school children’s (between 2 and 3.5 years old ability inmaking structured arrangement and their ability to determine the quantities bylooking at the arrangements. The result shows us that some of the children wereable to make such arrangement. However, the children found difficulties eitherto determine quantities from those arrangements or to compare some structuresto easily recognize number of objects.Keywords: structures, structured arrangement, cardinality DOI: http://dx.doi.org/10.22342/jme.1.1.790.53-70

  19. Birthday Cake Activity Structured Arrangement for Helping Children Determining Quantities

    Directory of Open Access Journals (Sweden)

    Neni Mariana

    2010-07-01

    Full Text Available Few researches have been concerned about relation between children’s spatial thinking and number sense. Narrowing for this small research, we focused on one component of spatial thinking, that is structuring objects, and one component of number senses, that is cardinality by determining quantities. This study focused on a design research that was conducted in Indonesia in which we investigated pre-school children’s (between 2 and 3.5 years old ability in making structured arrangement and their ability to determine the quantities by looking at the arrangements. The result shows us that some of the children were able to make such arrangement. However, the children found difficulties either to determine quantities from those arrangements or to compare some structures to easily recognize number of objects.

  20. Multimodal semantic quantity representations: further evidence from Korean Sign Language

    Directory of Open Access Journals (Sweden)

    Frank eDomahs

    2012-01-01

    Full Text Available Korean deaf signers performed a number comparison task on pairs of Arabic digits. In their RT profiles, the expected magnitude effect was systematically modified by properties of number signs in Korean Sign Language in a culture-specific way (not observed in hearing and deaf Germans or hearing Chinese. We conclude that finger-based quantity representations are automatically activated even in simple tasks with symbolic input although this may be irrelevant and even detrimental for task performance. These finger-based numerical representations are accessed in addition to another, more basic quantity system which is evidenced by the magnitude effect. In sum, these results are inconsistent with models assuming only one single amodal representation of numerical quantity.

  1. How tobacco companies have used package quantity for consumer targeting.

    Science.gov (United States)

    Persoskie, Alexander; Donaldson, Elisabeth A; Ryant, Chase

    2018-05-31

    Package quantity refers to the number of cigarettes or amount of other tobacco product in a package. Many countries restrict minimum cigarette package quantities to avoid low-cost packs that may lower barriers to youth smoking. We reviewed Truth Tobacco Industry Documents to understand tobacco companies' rationales for introducing new package quantities, including companies' expectations and research regarding how package quantity may influence consumer behaviour. A snowball sampling method (phase 1), a static search string (phase 2) and a follow-up snowball search (phase 3) identified 216 documents, mostly from the 1980s and 1990s, concerning cigarettes (200), roll-your-own tobacco (9), smokeless tobacco (6) and 'smokeless cigarettes' (1). Companies introduced small and large packages to motivate brand-switching and continued use among current users when faced with low market share or threats such as tax-induced price increases or competitors' use of price promotions. Companies developed and evaluated package quantities for specific brands and consumer segments. Large packages offered value-for-money and matched long-term, heavy users' consumption rates. Small packages were cheaper, matched consumption rates of newer and lighter users, and increased products' novelty, ease of carrying and perceived freshness. Some users also preferred small packages as a way to try to limit consumption or quit. Industry documents speculated about many potential effects of package quantity on appeal and use, depending on brand and consumer segment. The search was non-exhaustive, and we could not assess the quality of much of the research or other information on which the documents relied. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2018. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

  2. Quality or Quantity: A Statement for Teacher Training in Turkey

    Directory of Open Access Journals (Sweden)

    Ali AZAR

    2011-01-01

    Full Text Available Developed countries are initiating and implementing effective and appropriate technics in the field of teacher training. In Turkey, much research has been done in order to determine the qualification of teachers and, by this way, to train qualified teachers. Ministry of Education, Turkish Council of Higher Education, Faculties of Education and Faculties of Sciences have cooperated some certification systems, however, the research which is not supported by preliminary studies but exposured to political coercions lowered the quality of education. Besides, quantity is increased by pedagogical formation programs. In this study, Turkish teacher training system is analyzed with respect to quantity and quality.

  3. Manual of symbols and terminology for physicochemical quantities and units

    CERN Document Server

    Whiffen, D H

    2013-01-01

    Manual of Symbols and Terminology for Physicochemical Quantities and Units, 1979 Edition contains physical quantity tabulations of products. The Commission on Symbols, Terminology, and Units is a part of the Division of Physical Chemistry of the International Union of Pure and Applied Chemistry. Its general responsibilities are to secure clarity and precision, and wider agreement in the use of symbols, by chemists in different countries, among physicists, chemists, and engineers, and by editors of scientific journals. This book is composed of 13 chapters, and begins with the determination o

  4. Units for physical quantities used in dosimetry and radiation protection

    Energy Technology Data Exchange (ETDEWEB)

    Taubert, R; Wagner, S

    1976-04-01

    The 15th General Conference on Weights and Measures (1975) decided to introduce the name Becquerel for the SI unit of the quantity activity (1 Bq = 1 s/sup -1/) and the name Gray for the SI unit of ionizing radiations (1 Gy = 1 J/kg). The consequences of this latter decision are discussed. The Bundesanstalt is of the opinion that no further names for this unit should be introduced, but that the Gray should be used also for other quantities of the same dimension, especially for the dose equivalent.

  5. Studies on quantity and composition of dairy cow excreta

    International Nuclear Information System (INIS)

    Peschke, H.

    1982-01-01

    After feeding a lactating dairy cow a day ration completely enriched with 15 N, the quantities of feces and urine were registered over a period of ten days and put into proportion to the animal mass. The fecal dry matter was put into proportion to the dry matter of the fodder by means of 15 N analysis the N excretion with the excreta was determined concerning quantity and time. Selected feces and urine charges were used to produce a slurry model. The content of nutritive elements of the initial components and of the organic fertilizer are discussed. (author)

  6. Photosynthesis-related quantities for education and modeling.

    Science.gov (United States)

    Antal, Taras K; Kovalenko, Ilya B; Rubin, Andrew B; Tyystjärvi, Esa

    2013-11-01

    A quantitative understanding of the photosynthetic machinery depends largely on quantities, such as concentrations, sizes, absorption wavelengths, redox potentials, and rate constants. The present contribution is a collection of numbers and quantities related mainly to photosynthesis in higher plants. All numbers are taken directly from a literature or database source and the corresponding reference is provided. The numerical values, presented in this paper, provide ranges of values, obtained in specific experiments for specific organisms. However, the presented numbers can be useful for understanding the principles of structure and function of photosynthetic machinery and for guidance of future research.

  7. Synthesis of attapulgite/N-isopropylacrylamide and its use in drug release

    Energy Technology Data Exchange (ETDEWEB)

    Li, Xiaomo [Jiangsu Key Laboratory for Chemistry of Low-Dimensional Materials, School of Chemistry and Chemical Engineering, Huaiyin Normal University, Huaian 223300 (China); Faculty of Chemistry, Northeast Normal University, Changchun 130024, Jilin (China); Zhong, Hui, E-mail: huizhong@hytc.edu.cn [Jiangsu Key Laboratory for Chemistry of Low-Dimensional Materials, School of Chemistry and Chemical Engineering, Huaiyin Normal University, Huaian 223300 (China); Faculty of Chemistry, Northeast Normal University, Changchun 130024, Jilin (China); Li, Xiaorong, E-mail: lxr206206@163.com [Jiangsu Key Laboratory for Chemistry of Low-Dimensional Materials, School of Chemistry and Chemical Engineering, Huaiyin Normal University, Huaian 223300 (China); Jia, Feifei [Jiangsu Key Laboratory for Chemistry of Low-Dimensional Materials, School of Chemistry and Chemical Engineering, Huaiyin Normal University, Huaian 223300 (China); Faculty of Chemistry, Northeast Normal University, Changchun 130024, Jilin (China); Cheng, Zhipeng; Zhang, Lili; Yin, Jingzhou; An, Litao [Jiangsu Key Laboratory for Chemistry of Low-Dimensional Materials, School of Chemistry and Chemical Engineering, Huaiyin Normal University, Huaian 223300 (China); Guo, Liping, E-mail: guolp078@nenu.edu.cn [Faculty of Chemistry, Northeast Normal University, Changchun 130024, Jilin (China)

    2014-12-01

    Environmentally sensitive hydrogels as one of the most potential drug delivery systems have gained considerable interest in recent years. In the present study, we synthesized a newly temperature-responsive composite hydrogel based on attapulgite (ATP) and poly (N-isopropylacrylamide) (PNIPAM) as the localized drug carriers for drug delivery. The as-prepared ATP/PNIPAM hydrogel has large aperture which significantly improved the quantity of adsorption of drugs, exhibiting the excellent properties of drug release. The scanning electron microscope (SEM), Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), and X-ray diffraction (XRD) were used to characterize the ATP/PNIPAM. The swelling/deswelling behaviors and the release of ciprofloxacin lactate were studied. When the temperature was below the low critical solution temperature (LCST), the swelling property of hydrogels was excellent and the swelling rate was large. And, the drug release rate increased with the increase of the content of attapulgite in the composite hydrogel when it was put in the buffer solution (pH 7.38) at 37.0 °C. Therefore, the composite hydrogels might be very useful for its application in biomedical fields. - Highlights: • Attapulgite/N-isopropylacrylamide hydrogels were synthesized and characterized. • The swelling property of hydrogels was excellent when temperature was below 34.0 °C. • The composite hydrogels were used for the release of ciprofloxacin lactate. • The drug release rate increased with the increase of the content of attapulgite.

  8. Dams release methane even in temperate zoned

    International Nuclear Information System (INIS)

    Lemarchand, F.

    2010-01-01

    The Wohlen lake (near Bern) is a retaining dam built 90 years ago that has undergone a campaign to measure the quantity of methane released. The campaign lasted 1 year and the result was unexpected: 0.15 g/m 2 *day which one of the highest release rates in temperate zones. This result is all the more stunning since water stays only 2 days in average in the reservoir and that the drowned area is not important. In fact the river Aar that feeds the lake is loaded with organic matter coming from humane activities: agriculture and 3 sewage plants. This organic matter decays in the lake releasing methane. (A.C.)

  9. Fact Sheet: Clean Air Act Section 112(r): Accidental Release Prevention / Risk Management Plan Rule

    Science.gov (United States)

    EPA is required to publish regulations and guidance for chemical accident prevention at facilities that pose the greatest risk of harm from accidental releases of regulated flammable and toxic substances above threshold quantities.

  10. Quantities of natural gas transmitted in January-December 2012. Quantities of natural gas transported in January-December 2012

    International Nuclear Information System (INIS)

    2013-01-01

    GRTgaz is a European leader in natural gas transmission, a world expert in gas transmission networks and systems, and an operator firmly committed to the energy transition. It owns and operates the gas transmission network throughout most of France and it manages the transmission network in Germany, thereby helping to ensure correct operation of the French and European gas market. It contributes to the energy security of regional supply systems and performs a public service mission to ensure the continuity of consumer supply. This document presents the monthly key figures of GRTgaz activity in 2012: Total quantities transmitted by GRTgaz (Inputs to the GRTgaz network/Outputs from the GRTgaz network); Maximum and minimum daily flow (Daily quantities transported, Daily consumption, Daily inputs excluding storage); Quantities exchanged on the wholesale market; Consumption on the GRTgaz Network (gross monthly consumption and Average monthly temperatures)

  11. Toxics Release Inventory (TRI)

    Data.gov (United States)

    U.S. Environmental Protection Agency — The Toxics Release Inventory (TRI) is a dataset compiled by the U.S. Environmental Protection Agency (EPA). It contains information on the release and waste...

  12. Synthesis and Characterization of Low Solubility Poly Carbonyl Urea as a Slow Release Fertilizer

    International Nuclear Information System (INIS)

    Liu, Y.; Sun, X.

    2016-01-01

    Low solubility poly carbonyl urea has been successfully synthesized by the reaction of urea with methyl carbamate (MC) under the conditions of potassium carbonate as an initiator. It was characterized by FT-IR, /sup 13/C-NMR, and elemental analyser. In addition, the influences of the quantity of initiator, reaction temperature, reaction time and the molar ratio of starting materials on the conversion are discussed in detail. All those observations suggest that when initiator as 10 wt percent of urea, the reaction temperature 160 Degree C, 6 h, and n(urea):n(MC)=1:10, the reaction conversion rate can reach 78.4 percent. Moreover, the novel procedure is reported for the first time and has a significant N slow release properties, the N release in soil was 80 percent over 30 days. (author)

  13. Teacher quality and quantity as correlates of secondary school ...

    African Journals Online (AJOL)

    This study investigated the twin variables of quality and quantity of teachers as correlates of secondary school academic performance in Ogun State of Nigeria between 1997/98 and 2000/2001 academic sessions. The study was conducted ex-post facto under a descriptive survey research design using the proportional to ...

  14. 16 CFR 1.23 - Quantity limit rules.

    Science.gov (United States)

    2010-01-01

    ... 16 Commercial Practices 1 2010-01-01 2010-01-01 false Quantity limit rules. 1.23 Section 1.23 Commercial Practices FEDERAL TRADE COMMISSION ORGANIZATION, PROCEDURES AND RULES OF PRACTICE GENERAL... Robinson-Patman Act. These rules have the force and effect of law. [32 FR 8444, June 13, 1967. Redesignated...

  15. Quantity, Quality, and Satisfaction with Mentoring: What Matters Most?

    Science.gov (United States)

    Xu, Xiaohong; Payne, Stephanie C.

    2014-01-01

    According to Kram's mentor role theory, satisfaction with mentoring and mentorship quality are key indicators of effective and successful mentoring. We contribute to mentoring research by demonstrating the relative importance of mentorship quantity, mentorship quality, and satisfaction with mentoring to the prediction of job satisfaction,…

  16. 19 CFR 351.409 - Differences in quantities.

    Science.gov (United States)

    2010-04-01

    ... DUTIES Calculation of Export Price, Constructed Export Price, Fair Value, and Normal Value § 351.409... comparing export price or constructed export price with normal value, the Secretary will make a reasonable... section 773(a)(6)(C)(i) of the Act.) (b) Sales with quantity discounts in calculating normal value. The...

  17. Color Coding of Circuit Quantities in Introductory Circuit Analysis Instruction

    Science.gov (United States)

    Reisslein, Jana; Johnson, Amy M.; Reisslein, Martin

    2015-01-01

    Learning the analysis of electrical circuits represented by circuit diagrams is often challenging for novice students. An open research question in electrical circuit analysis instruction is whether color coding of the mathematical symbols (variables) that denote electrical quantities can improve circuit analysis learning. The present study…

  18. Thermodynamic quantities for the Klein–Gordon equation

    Indian Academy of Sciences (India)

    We study some thermodynamic quantities for the Klein–Gordon equation with a linear plus inverselinear, scalar potential. We obtain the energy eigenvalues with the help of the quantization rule from the biconfluent Heun's equation.We use a method based on the Euler–MacLaurin formula to analytically compute thethermal ...

  19. Thermodynamic quantities for the Klein–Gordon equation with a ...

    Indian Academy of Sciences (India)

    2017-02-01

    Feb 1, 2017 ... Abstract. We study some thermodynamic quantities for the Klein–Gordon equation with a linear plus inverse- linear, scalar potential. We obtain the energy eigenvalues with the help of the quantization rule from the biconfluent Heun's equation. We use a method based on the Euler–MacLaurin formula to ...

  20. Conserved quantities for stationary Einstein-Maxwell space-times

    International Nuclear Information System (INIS)

    Esposito, F.P.; Witten, L.

    1978-01-01

    It is shown that every stationary Einstein-Maxwell space-time has eight divergence-free vector fields and these are isolated in general form. The vector fields and associated conserved quantities are calculated for several families of space-times. (Auth.)

  1. Photographs in Dutch History Textbooks: Quantity, type and educational use

    NARCIS (Netherlands)

    M. Kleppe (Martijn)

    2010-01-01

    textabstractThis article demonstrates a media scientific approach by studying the use of photographs in Dutch History textbooks for High School pupils in the period 1970 – 2000. The quantity of photos has been determined as well as the types of pictures and its use as educational tool. Results show

  2. A colorimeter for measurement of picomole quantities of urea.

    Science.gov (United States)

    Vurek, G G; Knepper, M A

    1982-04-01

    We described a new colorimeter for the measurement of picomole quantities of urea in nanoliter volume fluid samples. The diacetyl monoxime reaction was used to produce a colored product from urea. The method is capable of resolving differences of 10 pmoles between samples containing 0 to 225 pmoles.

  3. Estimating waste disposal quantities from raw waste samples

    International Nuclear Information System (INIS)

    Negin, C.A.; Urland, C.S.; Hitz, C.G.; GPU Nuclear Corp., Middletown, PA)

    1985-01-01

    Estimating the disposal quantity of waste resulting from stabilization of radioactive sludge is complex because of the many factors relating to sample analysis results, radioactive decay, allowable disposal concentrations, and options for disposal containers. To facilitate this estimation, a microcomputer spread sheet template was created. The spread sheet has saved considerable engineering hours. 1 fig., 3 tabs

  4. Do Speakers and Listeners Observe the Gricean Maxim of Quantity?

    Science.gov (United States)

    Engelhardt, Paul E.; Bailey, Karl G. D.; Ferreira, Fernanda

    2006-01-01

    The Gricean Maxim of Quantity is believed to govern linguistic performance. Speakers are assumed to provide as much information as required for referent identification and no more, and listeners are believed to expect unambiguous but concise descriptions. In three experiments we examined the extent to which naive participants are sensitive to the…

  5. Whither the Nigerian Quantity Surveyors in the Information ...

    African Journals Online (AJOL)

    The paucity of information on the computing status of the quantity surveyors in Nigeria have been scanty and without empirical substantiation. The basic platform for entry to the information technology gateway is the acquisition, adoption and utilization of the computer. Baseline information is therefore indispensable for the ...

  6. Water quantity and quality at the urban-rural interface

    Science.gov (United States)

    Ge Sun; B. Graeme Lockaby

    2012-01-01

    Population growth and urban development dramatically alter natural watershed ecosystem structure and functions and stress water resources. We review studies on the impacts of urbanization on hydrologic and biogeochemical processes underlying stream water quantity and water quality issues, as well as water supply challenges in an urban environment. We conclude that...

  7. Hazardous Waste Management for the Small Quantity Generator. Teacher Edition.

    Science.gov (United States)

    Oklahoma State Dept. of Vocational and Technical Education, Stillwater. Curriculum and Instructional Materials Center.

    This instructional package for teaching about the regulations imposed on small quantity generators by the Environmental Protection Agency (EPA) under the Resource Conservation Recovery Act is organized around ll program objectives: students will be able to (l) determine a hazardous waste from lists or by identifying characteristics; (2) identify…

  8. Birthday Cake Activity Structured Arrangement for Helping Children Determining Quantities

    Science.gov (United States)

    Mariana, Neni

    2010-01-01

    Few researches have been concerned about relation between children's spatial thinking and number sense. Narrowing for this small research, we focused on one component of spatial thinking, that is structuring objects, and one component of number senses, that is cardinality by determining quantities. This study focused on a design research that was…

  9. 7 CFR 1427.170 - Quantity for loan.

    Science.gov (United States)

    2010-01-01

    ... to the preservation or safety of the loan collateral. Loans may be made on a lower percentage basis... 7 Agriculture 10 2010-01-01 2010-01-01 false Quantity for loan. 1427.170 Section 1427.170... OF AGRICULTURE LOANS, PURCHASES, AND OTHER OPERATIONS COTTON Recourse Seed Cotton Loans § 1427.170...

  10. Quantity and quality of written feedback, action plans, and student ...

    African Journals Online (AJOL)

    Background. Mini-clinical-evaluation exercise (mini-CEX) assessment forms that have been modified with the addition of specific spaces on separate sheets are expected to improve the quantity and quality of written feedback and the action plan for further learning which is agreed upon, and to encourage written reflection.

  11. Is the dose equivalent index a quantity to be measured

    International Nuclear Information System (INIS)

    Wagner, S.R.

    1980-01-01

    The following modifying factors are briefly considered in relation to the ambiguities and limitations of the Dose Equivalent Index: 1) Variations with time or of the movement of the exposed person 2) Irradiation geometry 3) Effect of radiation energy 4) Instrument performance and calibration, and other operational quantities. (U.K.)

  12. Threshold quantities for infectious diseases in periodic environments

    NARCIS (Netherlands)

    Heesterbeek, J.A.P.; Roberts, M.G.

    1995-01-01

    In this short note we give threshold quantities that determine the stability of the infection-free steady state for periodic deterministic systems that describe the spread of infectious diseases in populations whose individuals can be divided into a finite number of distinct groups. We concentrate

  13. An Adaptive Information Quantity-Based Broadcast Protocol for Safety Services in VANET

    Directory of Open Access Journals (Sweden)

    Wenjie Wang

    2016-01-01

    Full Text Available Vehicle-to-vehicle communication plays a significantly important role in implementing safe and efficient road traffic. When disseminating safety messages in the network, the information quantity on safety packets changes over time and space. However, most of existing protocols view each packet the same to disseminate, preventing vehicles from collecting more recent and precise safety information. Hence, an information quantity-based broadcast protocol is proposed in this paper to ensure the efficiency of safety messages dissemination. In particular, we propose the concept of emergency-degree to evaluate packets’ information quantity. Then we present EDCast, an emergency-degree-based broadcast protocol. EDCast differentiates each packet’s priority for accessing the channel based on its emergency-degree so as to provide vehicles with more safety information timely and accurately. In addition, an adaptive scheme is presented to ensure fast dissemination of messages in different network condition. We compare the performance of EDCast with those of three other representative protocols in a typical highway scenario. Simulation results indicate that EDCast achieves higher broadcast efficiency and less redundancy with less delivery delay. What we found demonstrates that it is feasible and necessary for incorporating information quantity of messages in designing an efficient safety message broadcast protocol.

  14. Comparative Assessment of Physical and Social Determinants of Water Quantity and Water Quality Concerns

    Science.gov (United States)

    Gunda, T.; Hornberger, G. M.

    2017-12-01

    Concerns over water resources have evolved over time, from physical availability to economic access and recently, to a more comprehensive study of "water security," which is inherently interdisciplinary because a secure water system is influenced by and affects both physical and social components. The concept of water security carries connotations of both an adequate supply of water as well as water that meets certain quality standards. Although the term "water security" has many interpretations in the literature, the research field has not yet developed a synthetic analysis of water security as both a quantity (availability) and quality (contamination) issue. Using qualitative comparative and multi-regression analyses, we evaluate the primary physical and social factors influencing U.S. states' water security from a quantity perspective and from a quality perspective. Water system characteristics are collated from academic and government sources and include access/use, governance, and sociodemographic, and ecosystem metrics. Our analysis indicates differences in variables driving availability and contamination concerns; for example, climate is a more significant determinant in water quantity-based security analyses than in water quality-based security analyses. We will also discuss coevolution of system traits and the merits of constructing a robust water security index based on the relative importance of metrics from our analyses. These insights will improve understanding of the complex interactions between quantity and quality aspects and thus, overall security of water systems.

  15. Energy Release in Solar Flares,

    Science.gov (United States)

    1982-10-01

    Plasma Research, Stanford University P. Kaufmanu CRAA/CNPq -Conseiho lacional de Desenvolvimento Cientifico e Tecnologico, Slo Paulo, SP, Brasil D.F...three phases of energy release in solar flares (Sturrock, 1980). However, a recent article by Feldman e a.. (1982) points to a significant

  16. Application of the radioreagent method to the determination of trace quantities of lead

    International Nuclear Information System (INIS)

    Figueiredo, A.M.G.; Saiki, M.; Lima, F.W. de

    1983-01-01

    The radioreagent method of analysis was applied to determine trace quantities of lead in several types of samples. This method is based on the extraction of radioactive cobalt, displaced by lead from the cobalt chelate of ethylenediaminetetraacetate labeled with 60 Co, into a tetracycline-benzyl alcohol solution. The radioactivity of the released cobalt, extracted into the organic phase, measured by menas of a single channel gamma-ray analyzer coupled to a Na(T1) scintillation detector, is proportional to the lead concentration. The elements which might interfere with the analysis were removed by a chemical separation procedure of lead using dithizone. The method was applied for lead determination in air samples, gasoline and samples from the International Atomic Energy Agency, namely: simulated air filter (Air-3), fresh water (W-3), dried animal whole blood(A-2) and calcinated animal bone (A3/1). The sensitivity, accuracy and precision of the method were also discussed. (Author) [pt

  17. IAEA regulatory initiatives for the air transport of large quantities of radioactive materials

    International Nuclear Information System (INIS)

    Luna, R.E.; Wangler, M.W.; Selling, H.A.

    1992-01-01

    The International Atomic Energy Agency (IAEA) has been laboring since 1988 over a far reaching change to its model regulations (IAEA, 1990) for the transport of radioactive materials (RAM). This change could impact the manner in which certain classes of radioactive materials are shipped by air and change some of the basic tenets of radioactive material transport regulations around the world. The impetus for this effort was spawned in part by the decision of the Japanese government to move large quantities of reprocessed plutonium by air from France to Japan. The exploration of options for overflights of United States and Canadian airspace (among others) and landings in Anchorage, Alaska, generated intense debate in the US and countries that might have been overflown. The debate centered on general questions of the need to air transport plutonium in large quantities, package survival in an accident, prenotification, emergency response, routing, safeguards and other facets of the proposed operations. In the US, which already had the most stringent regulations for packaging of plutonium shipped by air (NUREG-0360), there was immediate additional legislative action to increase the stringency by requiring demonstration that an aircraft carrying plutonium in certified packagings could undergo a severe crash without release of plutonium (the Murkowski amendment). In the United Kingdom there was an official inquiry that resulted in a high visibility report (ACTRAM 88) and a conclusion that the IAEA should examine regulatory needs in the general area of air transport

  18. Role of Leadership in Transforming the Profession of Quantity Surveying

    Directory of Open Access Journals (Sweden)

    George Ofori

    2012-11-01

    Full Text Available The construction industry is facing a period of change. The roles ofthe professions involved in the industry in general, and of quantitysurveyors in particular, are also changing. There are opportunitiesfor surveyors to seize the initiative to broaden their involvement inprojects, and attain strategic positions within the industry. However,they will have to improve upon their skill sets and their knowledgebases. Senior quantity surveyors interviewed in Singapore sharedtheir views on the challenges facing the construction industry,and their profession. They suggested that the quantity surveyingprofession would only be able to address the pressing issues itfaces if it pays more attention to innovation and the development ofits people. It should be able to attract and retain talent. Knowledgemanagement will be of critical importance. This will be enabled andfacilitated by knowledge leadership.

  19. Does quantity generate quality? Testing the fundamental principle of brainstorming.

    Science.gov (United States)

    Muñoz Adánez, Alfredo

    2005-11-01

    The purpose of this work is to test the chief principle of brainstorming, formulated as "quantity generates quality." The study is included within a broad program whose goal is to detect the strong and weak points of creative techniques. In a sample of 69 groups, containing between 3 and 8 members, the concurrence of two commonly accepted criteria was established as a quality rule: originality and utility or value. The results fully support the quantity-quality relation (r = .893): the more ideas produced to solve a problem, the better quality of the ideas. The importance of this finding, which supports Osborn's theory, is discussed, and the use of brainstorming is recommended to solve the many open problems faced by our society.

  20. On the operational quantity Hp(3) for eye lens dosimetry

    International Nuclear Information System (INIS)

    Behrens, R

    2012-01-01

    In the past the operational quantity H p (3) has been defined for calibration purposes in a slab phantom. Recently, an additional phantom in the form of a cylinder was suggested for eye lens dosimetry as a cylinder much better approximates the shape of a head than a slab. Therefore, this work investigates whether the quantity H p (3), when defined in the respective calibration phantom, adequately estimates the eye lens dose (or is at least conservative) depending on the phantom: it turns out that in most cases both calibration phantoms are similarly well suited. Finally, the definition of the eye lens dose is discussed together with possible consequences on the definition of H p (3): the consideration of only the radiation sensitive volume of the lens causes H p (3) not to be conservative in beta radiation fields. (paper)

  1. Dimensions of Organisational Culture in Quantity Surveying Firms in Nigeria

    Directory of Open Access Journals (Sweden)

    Ayokunle Olubunmi Olanipekun

    2014-12-01

    Full Text Available The functionalist paradigm of organisational culture (OC views culture as a variable subject to conscious manipulation and control in order to solve organisational challenges. Therefore, this paper provides information on how OC is a solution to the challenges in Quantity Surveying firms (QSFs.  This was achieved by eliciting the dimensions of OC in forty two QSFs in Lagos, Nigeria, which are the business, people and external environment dimensions. The paper concludes that OC is a relevant solution to the identity and management related challenges in QSFs. Specifically, the paper informs on the implications of business and people dimensions of OC as a solution to the identity challenges, as well as on the implication of the external environment dimension of OC to the management challenges. Based on the findings, practical implications and recommendations were directed at the management and employees QSs in QSFs and Quantity Surveying researchers.

  2. Conserved quantities for generalized KdV equations

    International Nuclear Information System (INIS)

    Calogero, F.; Rome Univ.; Degasperis, A.; Rome Univ.

    1980-01-01

    It is noted that the nonlinear evolution equation usub(t) = α(t)usub(xxx) - 6ν(t) usub(x)u, u is identical to u(x,t), possesses three (and, in some cases, four) conserved quantities, that are explicitly displayed. These results are of course relevant only to the cases in which this evolution equation is not known to possess an infinite number of conserved quantities. Purpose and scope of this paper is to report three or four simple conservation laws possessed by the evolution equation usub(t) = α(t)usub(xxx) - 6ν(t)usub(x)u, u is identical to u(x,t). (author)

  3. Securing water quality and quantity: Research and development perspective

    CSIR Research Space (South Africa)

    Pienaar, H

    2012-10-01

    Full Text Available : ? economic growth & development ? human & environmental needs ? meeting international obligations ? energy needs (strategic water users) ? ensuring availability and allocation (all other users) ? CSIR 2012 Slide 3 Background ? SA 30th driest country... and quantity: Research and development perspective 4th Biennial Conference Harrison Pienaar 10 October 2012 Presentation outline ? Introduction and background to water in South Africa ? Transboundary water resource aspects ? Water related challenges...

  4. Surface tension and related thermodynamic quantities of aqueous electrolyte solutions

    CERN Document Server

    Matubayasi, Norihiro

    2013-01-01

    Surface tension provides a thermodynamic avenue for analyzing systems in equilibrium and formulating phenomenological explanations for the behavior of constituent molecules in the surface region. While there are extensive experimental observations and established ideas regarding desorption of ions from the surfaces of aqueous salt solutions, a more successful discussion of the theory has recently emerged, which allows the quantitative calculation of the distribution of ions in the surface region. Surface Tension and Related Thermodynamic Quantities of Aqueous Electrolyte Solutions provides a d

  5. Synthesis of bulk quantity BN nanotubes with uniform morphology

    International Nuclear Information System (INIS)

    Wen, G.; Zhang, T.; Huang, X.X.; Zhong, B.; Zhang, X.D.; Yu, H.M.

    2010-01-01

    Bulk quantity hexagonal BN nanotubes (h-BNNTs) with uniform morphology were synthesized via an improved ball-milling and annealing method. The sample was characterized by X-ray photoelectron spectrometry, electron energy loss spectroscopy, X-ray diffraction, scanning electron microscopy, conventional transmission electron microscopy (TEM) and high-resolution TEM. The results show that the fabricated BNNTs have a uniform diameter ranging from 80 to 100 nm and a length of about 50-60 μm.

  6. Monitoring the eye lens: which dose quantity is adequate?

    International Nuclear Information System (INIS)

    Behrens, R; Dietze, G

    2010-01-01

    Recent epidemiological studies suggest a rather low dose threshold (below 0.5 Gy) for the induction of a cataract of the eye lens. Some other studies even assume that there is no threshold at all. Therefore, protection measures have to be optimized and current dose limits for the eye lens may be reduced in the future. The question of which personal dose equivalent quantity is appropriate for monitoring the dose to the eye lens arises from this situation. While in many countries dosemeters calibrated in terms of the dose equivalent quantity H p (0.07) have been seen as being adequate for monitoring the dose to the eye lens, this might be questionable in the case of reduced dose limits and, thus, it may become necessary to use the dose equivalent quantity H p (3) for this purpose. To discuss this question, the dose conversion coefficients for the equivalent dose of the eye lens (in the following eye lens dose) were determined for realistic photon and beta radiation fields and compared with the values of the corresponding conversion coefficients for the different operational quantities. The values obtained lead to the following conclusions: in radiation fields where most of the dose comes from photons, especially x-rays, it is appropriate to use dosemeters calibrated in terms of H p (0.07) on a slab phantom, while in other radiation fields (dominated by beta radiation or unknown contributions of photon and beta radiation) dosemeters calibrated in terms of H p (3) on a slab phantom should be used. As an alternative, dosemeters calibrated in terms of H p (0.07) on a slab phantom could also be used; however, in radiation fields containing beta radiation with the end point energy near 1 MeV, an overestimation of the eye lens dose by up to a factor of 550 is possible.

  7. Mass spectrometry of submicrogram quantities of lead and cadmium

    International Nuclear Information System (INIS)

    Moraes, Noemia M.P. de; Kakazu, M.H.; Iyer, S.S.

    1980-01-01

    Isotope analyses of submicrogram quantities of lead and cadmium are carried out by single filament solid source mass spectrometry. Thermionic emission of Pb and Cd is enhanced using silica gel as an emitter. Details of the chemical and mass spectrometric techniques are described. The low blank levels are maintained by extra purification of the reagents. The applications of isotope ratios of Pb and Cd in environmental sciences and geochemistry are discussed. (Author) [pt

  8. Effects of nonindigenous invasive species on water quality and quantity

    Science.gov (United States)

    Frank H. McCormick; Glen C. Contreras; Sherri L. Johnson

    2010-01-01

    Physical and biological disruptions of aquatic systems caused by invasive species alter water quantity and water quality. Recent evidence suggests that water is a vector for the spread of Sudden Oak Death disease and Port-Orfordcedar root disease. Since the 1990s, the public has become increasingly aware of the presence of invasive species in the Nation’s waters. Media...

  9. A Cross-Sectional Snapshot of Sleep Quality and Quantity Among US Medical Students.

    Science.gov (United States)

    Ayala, Erin E; Berry, Rani; Winseman, Jeffrey S; Mason, Hyacinth Rc

    2017-10-01

    Fatigue is a well-known risk factor for mood disturbances, decreased cognitive acuity, and impaired judgment. Sleep research in medical students typically focuses on sleep quantity, but less is known about the quality of a student's sleep. The purpose of this investigation was to examine the subjective sleep quality and quantity of US medical students and to identify differences in sleep characteristics across demographic groups. Medical students (N = 860) representing 49 medical colleges completed the Medical Outcomes Study Sleep Scale and a demographic questionnaire between December 2015 and March 2016. Although participants reported obtaining nearly 7 h of sleep per night, the majority of students reported indicators of poor sleep quality. First and third year students reported higher rates of sleep-related problems compared to second and fourth year students. First and second year students reported the highest levels of sleep somnolence. Ethnic minority students reported significantly lower levels of sleep adequacy and sleep quantity and significantly higher levels of sleep somnolence than Caucasian students. Impaired sleep quality may contribute to fatigue in medical students even when sleep quantity seems adequate. Students appear to begin medical school with disrupted sleep patterns that may not improve until their final year of study. Education regarding proper sleep habits and the significant role of sleep quality in sustaining healthy sleep is especially important in the early stages of medical education. Minority, first year, and third year students may benefit the most from learning new behaviors that promote sufficient sleep quality during periods of sustained stress.

  10. Multidemand Multisource Order Quantity Allocation with Multiple Transportation Alternatives

    Directory of Open Access Journals (Sweden)

    Jun Gang

    2015-01-01

    Full Text Available This paper focuses on a multidemand multisource order quantity allocation problem with multiple transportation alternatives. To solve this problem, a bilevel multiobjective programming model under a mixed uncertain environment is proposed. Two levels of decision makers are considered in the model. On the upper level, the purchaser aims to allocate order quantity to multiple suppliers for each demand node with the consideration of three objectives: total purchase cost minimization, total delay risk minimization, and total defect risk minimization. On the lower level, each supplier attempts to optimize the transportation alternatives with total transportation and penalty costs minimization as the objective. In contrast to prior studies, considering the information asymmetry in the bilevel decision, random and fuzzy random variables are used to model uncertain parameters of the construction company and the suppliers. To solve the bilevel model, a solution method based on Kuhn-Tucker conditions, sectional genetic algorithm, and fuzzy random simulation is proposed. Finally, the applicability of the proposed model and algorithm is evaluated through a practical case from a large scale construction project. The results show that the proposed model and algorithm are efficient in dealing with practical order quantity allocation problems.

  11. Entropy and Its Correlations with Other Related Quantities

    Directory of Open Access Journals (Sweden)

    Jing Wu

    2014-02-01

    Full Text Available In order to find more correlations between entropy and other related quantities, an analogical analysis is conducted between thermal science and other branches of physics. Potential energy in various forms is the product of a conserved extensive quantity (for example, mass or electric charge and an intensive quantity which is its potential (for example, gravitational potential or electrical voltage, while energy in specific form is a dissipative quantity during irreversible transfer process (for example mechanical or electrical energy will be dissipated as thermal energy. However, it has been shown that heat or thermal energy, like mass or electric charge, is conserved during heat transfer processes. When a heat transfer process is for object heating or cooling, the potential of internal energy U is the temperature T and its potential “energy” is UT/2 (called entransy and it is the simplified expression of thermomass potential energy; when a heat transfer process is for heat-work conversion, the potential of internal energy U is (1 − T0/T, and the available potential energy of a system in reversible heat interaction with the environment is U − U0 − T0(S − S0, then T0/T and T0(S − S0 are the unavailable potential and the unavailable potential energy of a system respectively. Hence, entropy is related to the unavailable potential energy per unit environmental temperature for heat-work conversion during reversible heat interaction between the system and its environment. Entropy transfer, like other forms of potential energy transfer, is the product of the heat and its potential, the reciprocal of temperature, although it is in form of the quotient of the heat and the temperature. Thus, the physical essence of entropy transfer is the unavailable potential energy transfer per unit environmental temperature. Entropy is a non-conserved, extensive, state quantity of a system, and entropy generation in an irreversible heat transfer process

  12. Quantities of arsenic-treated wood in demolition debris generated by Hurricane Katrina.

    Science.gov (United States)

    Dubey, Brajesh; Solo-Gabriele, Helena M; Townsendt, Timothy G

    2007-03-01

    The disaster debris from Hurricane Katrina is one of the largest in terms of volume and economic loss in American history. One of the major components of the demolition debris is wood waste of which a significant proportion is treated with preservatives, including preservatives containing arsenic. As a result of the large scale destruction of treated wood structures such as electrical poles, fences, decks, and homes a considerable amount of treated wood and consequently arsenic will be disposed as disaster debris. In this study an effort was made to estimate the quantity of arsenic disposed through demolition debris generated in the Louisiana and Mississippi area through Hurricane Katrina. Of the 72 million cubic meters of disaster debris generated, roughly 12 million cubic meters were in the form of construction and demolition wood resulting in an estimated 1740 metric tons of arsenic disposed. Management of disaster debris should consider the relatively large quantities of arsenic associated with pressure-treated wood.

  13. Groundwater Quantity and Quality Issues in a Water-Rich Region: Examples from Wisconsin, USA

    Directory of Open Access Journals (Sweden)

    John Luczaj

    2015-06-01

    Full Text Available The State of Wisconsin is located in an unusually water-rich portion of the world in the western part of the Great Lakes region of North America. This article presents an overview of the major groundwater quantity and quality concerns for this region in a geologic context. The water quantity concerns are most prominent in the central sand plain region and portions of a Paleozoic confined sandstone aquifer in eastern Wisconsin. Water quality concerns are more varied, with significant impacts from both naturally occurring inorganic contaminants and anthropogenic sources. Naturally occurring contaminants include radium, arsenic and associated heavy metals, fluoride, strontium, and others. Anthropogenic contaminants include nitrate, bacteria, viruses, as well as endocrine disrupting compounds. Groundwater quality in the region is highly dependent upon local geology and land use, but water bearing geologic units of all ages, Precambrian through Quaternary, are impacted by at least one kind of contaminant.

  14. Impact of Fruit Piece Structure in Yogurts on the Dynamics of Aroma Release and Sensory Perception

    Directory of Open Access Journals (Sweden)

    Isabelle Souchon

    2013-05-01

    Full Text Available The aim of this work was to gain insight into the effect of food formulation on aroma release and perception, both of which playing an important role in food appreciation. The quality and quantity of retronasal aroma released during food consumption affect the exposure time of olfactory receptors to aroma stimuli, which can influence nutritional and hedonic characteristics, as well as consumption behaviors. In yogurts, fruit preparation formulation can be a key factor to modulate aroma stimulation. In this context, the impact of size and hardness of fruit pieces in fat-free pear yogurts was studied. Proton Transfer Reaction-Mass Spectrometry (PTR-MS was used to allow sensitive and on-line monitoring of volatile odorous compound release in the breath during consumption. In parallel, a trained panel used sensory profile and Temporal Dominance of Sensations (TDS methods to characterize yogurt sensory properties and their dynamic changes during consumption. Results showed that the size of pear pieces had few effects on aroma release and perception of yogurts, whereas fruit hardness significantly influenced them. Despite the fact that yogurts presented short and similar residence times in the mouth, this study showed that fruit preparation could be an interesting formulation factor to enhance exposure time to stimuli and thus modify food consumption behaviors. These results could be taken into account to formulate new products that integrate both nutritional and sensory criteria.

  15. Change regularity of water quality parameters in leakage flow conditions and their relationship with iron release.

    Science.gov (United States)

    Liu, Jingqing; Shentu, Huabin; Chen, Huanyu; Ye, Ping; Xu, Bing; Zhang, Yifu; Bastani, Hamid; Peng, Hongxi; Chen, Lei; Zhang, Tuqiao

    2017-11-01

    The long-term stagnation in metal water supply pipes, usually caused by intermittent consumption patterns, will cause significant iron release and water quality deterioration, especially at the terminus of pipelines. Another common phenomenon at the terminus of pipelines is leakage, which is considered helpful by allowing seepage of low-quality drinking water resulting from long-term stagnation. In this study, the effect of laminar flow on alleviating water quality deterioration under different leakage conditions was investigated, and the potential thresholds of the flow rate, which can affect the iron release process, were discussed. Based on a galvanized pipe and ductile cast iron pipe pilot platform, which was established at the terminus of pipelines, this research was carried out by setting a series of leakage rate gradients to analyze the influence of different leakage flow rates on iron release, as well as the relationship with chemical and biological parameters. The results showed that the water quality parameters were obviously influenced by the change in flow velocity. Water quality was gradually improved with an increase in flow velocity, but its change regularity reflected a diversity under different flow rates (p water distribution system, when the bulk water was at the critical laminar flow velocity, the concentration of total iron, the quantity and rate of total iron release remain relatively in an ideal and safe situation. Copyright © 2017. Published by Elsevier Ltd.

  16. Remarks and suggestions concerned with formulation of the definition of quantity ''committed dose'' and quantity ''radiation burden'' useful in estimates of population exposure

    International Nuclear Information System (INIS)

    Cwik, T.

    1990-01-01

    The paper contains remarks to the definitions of the quantity ''commited dose'' given in the publications of the ICRP. The suggestions are presented on the mode of formulating the definition of the quantity ''commited dose'' and the definition of the quantity denoted hitherto by the symbol H 50 . The other suggestions deal with introduction of the quantity ''radiation burden'', assigned for use in assessments of irradiation expressed ''per caput'' of population. 9 refs. (author)

  17. Dangerous quantities of radioactive material (D-values)

    International Nuclear Information System (INIS)

    2010-01-01

    Radioactive material is widely used in industry, medicine, education and agriculture. In addition, it occurs naturally. The health risk posed by these materials vary widely depending on many factors, the most important of which are the amount of the material involved and its physical and chemical form. Therefore, there is a need to identify the quantity and type of radioactive material for which emergency preparedness and other arrangements (e.g. security) are warrant due to the health risk they pose. The aim of this publication is to provide practical guidance for Member States on that quantity of radioactive material that may be considered dangerous. A dangerous quantity is that, which if uncontrolled, could be involved in a reasonable scenario resulting in the death of an exposed individual or a permanent injury, which decreases that person's quality of life. This publication is published as part of the IAEA Emergency Preparedness and Response Series. It supports several publications including: the IAEA Safety Requirements 'Preparedness and Response for a Nuclear or Radiological Emergency', IAEA Safety Standards Series No. GS-R-2. IAEA, Vienna (2002). IAEA Safety Guide 'Categorization of Radioactive Sources', IAEA Safety Standards Series No RS-G-1.9, IAEA, Vienna (2005) and IAEA Safety Guide 'Arrangements for Preparedness for a Nuclear or Radiological Emergency' IAEA Safety Standards Series No. GS-G-2.1, IAEA, Vienna (2006). The procedures and data in this publication have been prepared with due attention to accuracy. However, as part of the review process, they undergo ongoing quality assurance checks. Comments are welcome and, following a period that will allow for a more extensive review, the IAEA may revise this publication as part of the process of continuous improvement. The publication uses a number of exposure scenarios, risk models and dosimetric data, which could be used during the response to nuclear or radiological emergency or other purposes

  18. Solvation quantities from a COSMO-RS equation of state

    International Nuclear Information System (INIS)

    Panayiotou, C.; Tsivintzelis, I.; Aslanidou, D.; Hatzimanikatis, V.

    2015-01-01

    Highlights: • Extension of the successful COSMO-RS model to an equation-of-state model. • Two scaling constants, obtained from atom-specific contributions. • Overall estimation of the solvation quantities and contributions. - Abstract: This work focuses on the extension of the successful COSMO-RS model of mixtures into an equation-of-state model of fluids and its application for the estimation of solvation/hydration quantities of a variety of chemical substances. These quantities include free-energies, enthalpies and entropies of hydration as well as the separate contributions to each of them. Emphasis is given on the estimation of contributions from the conformational changes of solutes upon solvation and the associated restructuring of solvent in its immediate neighborhood. COSMO-RS is a quantum-mechanics based group/segment contribution model in which the Quasi-Chemical (QC) approach is used for the description of the non-random distribution of interacting segments in the system. Thus, the equation-of-state development is done through such a QC framework. The new model will not need any adjustable parameters for the strong specific interactions, such as hydrogen bonds, since they will be provided by the quantum-mechanics based cosmo-files – a key feature of COSMO-RS model. It will need, however, one volumetric and one energy parameter per fluid, which are scaling constants or molecular descriptors of the fluid and are obtained from rather easily available data such as densities, boiling points, vapor pressures, heats of vaporization or second virial coefficients. The performance and the potential of the new equation-of-state model to become a fully predictive model are critically discussed

  19. Radiation quantities, units and measurements. Final report 1999

    International Nuclear Information System (INIS)

    Wambersie, A.; Allisy, A.; Caswell, R.S.

    2000-01-01

    The determination of human exposure to radiation and radioactivity, whether arising from environmental exposures, medical practice or industrial activities, requires a fundamental set of quantities and units with which exposures can be specified and the means and ability to make measurements which yield results in terms of these quantities and units. Radiation protection then, as well as effective use of radiation in medical applications, requires the capability to accurately quantify the characteristics and extent of radiation exposure, so that appropriate and useful assessments of the potential health consequences and risks, whether for protection of the public and workers or for diagnosis and treatment of disease, can be formulated. The work carried out via this concerted action on ''Radiation quantities, units and measurements'' has addressed these needs. Measurement of radiation is a complex subject and is a science in itself. Yet many users of radiation who need to make radiation measurements cannot be expected to become experts in this particular field. They need authoritative guidance on how to deal with the measurement problems connected with their particular use of radiation. The work carried out pursuant to this concerted action has resulted in publications that meet this need. Important achievements include the publication of seven new ICRU reports, the completion of all but the printing of three other ICRU reports, completion of the drafting work on two other reports, the development of many others reports and the initiation of seven new activities that will result in ICRU reports representing important future contribution to the needs identified in this project. (orig.)

  20. Preparation and Evaluation of Oxaliplatin Thermosensitive Liposomes with Rapid Release and High Stability.

    Directory of Open Access Journals (Sweden)

    Chunying Zeng

    Full Text Available Oxaliplatin (OXP was reported to show low anti-tumor activity when used alone and to display side effects; this low activity was attributed to high partitioning to erythrocytes and low accumulation in tumors. Thermosensitive liposomes (TSL were considered able to specifically deliver drugs to heated tumors and to resolve the OXP distribution problem. Regretfully, TSL encapsulating doxorubicin did not demonstrate significant improvement in progression-free survival. Drug release below 41°C and significant leakage were considered major reasons for the failure. The purpose of this study was to acquire OXP TSL with rapid release at the triggered temperature and high stability at body temperature and at storage temperatures. A small quantity of poloxamer 188 was introduced into the TSL formulation to stabilize the encapsulated drug. It was shown that the addition of poloxamer 188 had no influence on the TSL characteristics. More than 90% of OXP was released within 10 min at 42°C, and less than 15% was released within 60 min at temperatures below 39°C. TSL were stable at 37°C for 96 h and at 4°C for 6 months. The anti-tumor activity of TSL at the dose of 2.5 mg/kg was certified to be equal to those of OXP injection and non-thermosensitive liposomes (NTSL at the dose of 5 mg/kg, and significant improvement of tumor inhibition was observed in TSL compared with injection and NTSL at the same dose. It was also shown from the histological transmutation of tumors that TSL had stronger anti-tumor activity. Therefore, it could be concluded that TSL composed of a proper amount of poloxamer had rapid release and high stability, and OXP TSL would be anticipated to exert prominent anti-tumor activity in the clinic.

  1. Evaluating the uncertainty of input quantities in measurement models

    Science.gov (United States)

    Possolo, Antonio; Elster, Clemens

    2014-06-01

    The Guide to the Expression of Uncertainty in Measurement (GUM) gives guidance about how values and uncertainties should be assigned to the input quantities that appear in measurement models. This contribution offers a concrete proposal for how that guidance may be updated in light of the advances in the evaluation and expression of measurement uncertainty that were made in the course of the twenty years that have elapsed since the publication of the GUM, and also considering situations that the GUM does not yet contemplate. Our motivation is the ongoing conversation about a new edition of the GUM. While generally we favour a Bayesian approach to uncertainty evaluation, we also recognize the value that other approaches may bring to the problems considered here, and focus on methods for uncertainty evaluation and propagation that are widely applicable, including to cases that the GUM has not yet addressed. In addition to Bayesian methods, we discuss maximum-likelihood estimation, robust statistical methods, and measurement models where values of nominal properties play the same role that input quantities play in traditional models. We illustrate these general-purpose techniques in concrete examples, employing data sets that are realistic but that also are of conveniently small sizes. The supplementary material available online lists the R computer code that we have used to produce these examples (stacks.iop.org/Met/51/3/339/mmedia). Although we strive to stay close to clause 4 of the GUM, which addresses the evaluation of uncertainty for input quantities, we depart from it as we review the classes of measurement models that we believe are generally useful in contemporary measurement science. We also considerably expand and update the treatment that the GUM gives to Type B evaluations of uncertainty: reviewing the state-of-the-art, disciplined approach to the elicitation of expert knowledge, and its encapsulation in probability distributions that are usable in

  2. Comparison of simulated and measured quantities of a duplex reactor

    Energy Technology Data Exchange (ETDEWEB)

    Koskela, M.; Kajava, M. [ABB Marine, Helsinki (Finland)

    1997-12-31

    The purpose of this article is to illustrate the use of an analog simulator as a design tool when designing new power electric equipment. The purpose of simulation is to predict the functionality of electrical equipment to be constructed. Duplex reactor is an electromagnetic device designed to reduce voltage harmonics and short circuit currents in the ship electrical network. In this report a comparison between simulated and measured electrical quantities of a duplex reactor has been made. The purpose of the measurements was to show the correct functioning of the reactor. The simulation results and the measured waveforms corresponds well to each other. (orig.) 4 refs.

  3. Sustainable economic production quantity models for inventory systems with shortage

    DEFF Research Database (Denmark)

    Taleizadeh, Ata Allah; Soleymanfar, Vahid Reza; Govindan, Kannan

    2018-01-01

    optimal values of inventory system variables, we solve four independent profit maximization problems for four different situations. These proposed models include a basic model in which shortages are not allowed, and when shortages are allowed, the lost sale, full backordering and partial backordering...... (EPQ). The theoretical sustainable EOQ and EPQ models are basic models that ignore many real-life conditions such as the possibility of stock-out in inventory systems. In this paper, we develop four new sustainable economic production quantity models that consider different shortage situations. To find...

  4. Net present value analysis of the economic production quantity

    OpenAIRE

    Disney, Stephen Michael; Warburton, R. D. H.; Zhong, Q. C.

    2013-01-01

    Using Laplace transforms we extend the economic production quantity (EPQ) model by analysing cash flows from a net present value (NPV) viewpoint. We obtain an exact expression for the present value of the cash flows in the EPQ problem. From this, we are able to derive the optimal batch size. We obtain insights into the monotonicity and convexity of the present value of each of the cash flows, and show that there is a unique minimum in the present value of the sum of the cash flows in the exte...

  5. Ultracold atoms for precision measurement of fundamental physical quantities

    CERN Multimedia

    CERN. Geneva

    2003-01-01

    Cooling and trapping of neutral atoms has been one of the most active fields of research in physics in recent years. Several methods were demonstrated to reach temperatures as low as a few nanokelvin allowing, for example, the investigation of quantum degenerate gases. The ability to control the quantum degrees of freedom of atoms opens the way to applications for precision measurement of fundamental physical quantities. Experiments in progress, planned or being considered using new quantum devices based on ultracold atoms, namely atom interferometers and atomic clocks, will be discussed.

  6. Physical quantities related to measurement campaigns for cooling towers

    International Nuclear Information System (INIS)

    Boegel, W.

    1975-12-01

    The nomenclature in reports on the measurement campaigns for cooling towers will be adapted as far as possible to the already existing VDI report on this subject. On the other hand, the appropriate standards will also be accounted for. In order to facilitate a decision in individual cases in a first table the meteorologically or generally interesting quantities of the VDI reports are compared with the German, international, and WMO standards and - if necessary - also commented. A second table contains the air humidity parameters standardized by WMO including brief definitions. (orig/HP) [de

  7. MICROMICETES QUANTITY AND BIOMASS IN TECHNOGENIC AND NATURAL SOILS

    Directory of Open Access Journals (Sweden)

    O. N. Korinovskaya

    2014-08-01

    Full Text Available It is shown that in edaphotopes around of freight checkpoint of CJSC «Krivorozhskiy Surikovyy Zavod», ore-enrichment factory and fresh-inwashed pool of tailings dam of PJSC «Northern Iron Ore Enrichment Works» there is an increase of heavy metals mobile forms (which are the most dangerous for microorganisms, plants, animals and human: for iron in 310; for zinc - in 4,3-6,5; for lead - in 3.2-5.7; for cadmium - in 5,6-9,8; for copper – 6,8-66,5 and for nickel - in 9 times as compared to zonal soil. Whereas in soils of CJSC «Krivorozhskiy Surikovyy Zavod» sanitary protection zone number of copper, nickel, lead, cadmium and zinc mobile forms exceeded the control values in 2,4-6,6 times. For the first time the features of soil microscopic fungi seasonal dynamics of quantity in industrial disturbed soils of Kryvorizhzhya compared to zonal soil (chernozem usual were registered. Changes in fungal mycelium length and biomass, its spore’s amount and biomass in edaphotopes of ore-enrichment and chemical enterprises and of common chernozem are also presented. It is shown that in edaphotopes of heavy contamination areas of «Krivorozhskiy Surikovyy Zavod» and of «Northern Iron Ore Enrichment Works» in spring, summer, and autumn there was decrease of microscopic fungi quantity in 4-10 times, moreover in tehnozems of «Northern Iron Ore Enrichment Works» fresh-inwashed pool of tailings dam their amount reduces in more than 100 times, compared with common chernozem. In low contamination area of «Krivorozhskiy Surikovyy Zavod» their quantity decreases in 2 times. Also in heavy contamination areas of chemical and ore-enrichment enterprises there is strong decrease in the length of fungal mycelium in 2.7-4.2 times, its biomass in 2,6-4,5 times, the spores amount - in 4,5-7,7 times and their biomass - in 10,5-21 times compared to the natural soil, which could be explained by high contents of toxicants. While in the sanitary protection zone of the

  8. Documentation and analysis for packaging limited quantity ice chests

    International Nuclear Information System (INIS)

    Nguyen, P.M.

    1995-01-01

    The purpose of this Documentation and Analysis for Packaging (DAP) is to document that ice chests meet the intent of the International Air Transport Association (IATA) and the U.S. Department of Transportation (DOT) Code of Federal Regulations as strong, tight containers for the packaging of limited quantities for transport. This DAP also outlines the packaging method used to protect the sample bottles from breakage. Because the ice chests meet the DOT requirements, they can be used to ship LTD QTY on the Hanford Site

  9. Investigation on Capability of Reaming Process using Minimal Quantity Lubrication

    DEFF Research Database (Denmark)

    De Chiffre, Leonardo; Tosello, Guido; Piska, Miroslav

    2008-01-01

    An investigation on reaming using minimal quantity lubrication (MQL) was carried out with the scope of documenting process capability using a metrological approach. Reaming tests were carried out on austenitic stainless steel, using HSS reamers with different cutting data and lubrication conditions...... depth of cut was employed. The suitability of MQL for reaming was proven under the investigated process conditions, concerning both the quality of the machined holes, in terms of geometrical characteristics and surface finishing, and the process quality, with respect to reaming torque and thrust, along...

  10. Large scientific releases

    International Nuclear Information System (INIS)

    Pongratz, M.B.

    1981-01-01

    The motivation for active experiments in space is considered, taking into account the use of active techniques to obtain a better understanding of the natural space environment, the utilization of the advantages of space as a laboratory to study fundamental plasma physics, and the employment of active techniques to determine the magnitude, degree, and consequences of artificial modification of the space environment. It is pointed out that mass-injection experiments in space plasmas began about twenty years ago with the Project Firefly releases. Attention is given to mass-release techniques and diagnostics, operational aspects of mass release active experiments, the active observation of mass release experiments, active perturbation mass release experiments, simulating an artificial modification of the space environment, and active experiments to study fundamental plasma physics

  11. The release of dissolved nutrients and metals from coastal sediments due to resuspension

    Science.gov (United States)

    Kalnejais, Linda H.; Martin, William R.; Bothner, Michael H.

    2010-01-01

    Coastal sediments in many regions are impacted by high levels of contaminants. Due to a combination of shallow water depths, waves, and currents, these sediments are subject to regular episodes of sediment resuspension. However, the influence of such disturbances on sediment chemistry and the release of solutes is poorly understood. The aim of this study is to quantify the release of dissolved metals (iron, manganese, silver, copper, and lead) and nutrients due to resuspension in Boston Harbor, Massachusetts, USA. Using a laboratory-based erosion chamber, a range of typical shear stresses was applied to fine-grained Harbor sediments and the solute concentration at each shear stress was measured. At low shear stress, below the erosion threshold, limited solutes were released. Beyond the erosion threshold, a release of all solutes, except lead, was observed and the concentrations increased with shear stress. The release was greater than could be accounted for by conservative mixing of porewaters into the overlying water, suggesting that sediment resuspension enhances the release of nutrients and metals to the dissolved phase. To address the long-term fate of resuspended particles, samples from the erosion chamber were maintained in suspension for 90. h. Over this time, 5-7% of the particulate copper and silver was released to the dissolved phase, while manganese was removed from solution. Thus resuspension releases solutes both during erosion events and over a longer timescale due to reactions of suspended particles in the water column. The magnitude of the annual solute release during erosion events was estimated by coupling the erosion chamber results with a record of bottom shear stresses simulated by a hydrodynamic model. The release of dissolved copper, lead, and phosphate due to resuspension is between 2% and 10% of the total (dissolved plus particulate phase) known inputs to Boston Harbor. Sediment resuspension is responsible for transferring a significant

  12. A statistical law in the perception of risks and physical quantities in traffic

    DEFF Research Database (Denmark)

    Elvik, Rune

    2015-01-01

    This paper suggests that a universal psychophysical law influences the perception of risks and physical quantities in traffic. This law states that there will be a tendency to overestimate low probabilities or small quantities, while high probabilities or large quantities may be underestimated....... Studies of the perception of risk and physical quantities in traffic have found a highly consistent pattern....

  13. Water quantity and quality optimization modeling of dams operation based on SWAT in Wenyu River Catchment, China.

    Science.gov (United States)

    Zhang, Yongyong; Xia, Jun; Chen, Junfeng; Zhang, Minghua

    2011-02-01

    Water quantity and quality joint operation is a new mode in the present dams' operation research. It has become a hot topic in governmental efforts toward integrated basin improvement. This paper coupled a water quantity and quality joint operation model (QCmode) and genetic algorithm with Soil and Water Assessment Tool (SWAT). Together, these tools were used to explore a reasonable operation of dams and floodgates at the basin scale. Wenyu River Catchment, a key area in Beijing, was selected as the case study. Results showed that the coupled water quantity and quality model of Wenyu River Catchment more realistically simulates the process of water quantity and quality control by dams and floodgates. This integrated model provides the foundation for research of water quantity and quality optimization on dam operation in Wenyu River Catchment. The results of this modeling also suggest that current water quality of Wenyu River will improve following the implementation of the optimized operation of the main dams and floodgates. By pollution control and water quantity and quality joint operation of dams and floodgates, water quality of Wenyu river will change significantly, and the available water resources will increase by 134%, 32%, 17%, and 82% at the downstream sites of Sha River Reservoir, Lutong Floodgate, Xinpu Floodgate, and Weigou Floodgate, respectively. The water quantity and quality joint operation of dams will play an active role in improving water quality and water use efficiency in Wenyu River Basin. The research will provide the technical support for water pollution control and ecological restoration in Wenyu River Catchment and could be applied to other basins with large number of dams. Its application to the Wenyu River Catchment has a great significance for the sustainable economic development of Beijing City.

  14. 40 CFR 721.90 - Release to water.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Release to water. 721.90 Section 721... SIGNIFICANT NEW USES OF CHEMICAL SUBSTANCES Certain Significant New Uses § 721.90 Release to water. Whenever a... predict the surface water concentration which will result from the intended release of the substance, if...

  15. Development of blueberry liquor: influence of distillate, sweetener and fruit quantity.

    Science.gov (United States)

    Caldeira, Ilda; Lopes, Daniel; Delgado, Teresa; Canas, Sara; Anjos, Ofélia

    2018-02-01

    In this work different formulations of blueberry liquor were tested and characterised based on their physico-chemical and sensory characteristics. Three factors were evaluated: the distillate used to produce the liquor (wine spirit or grape marc spirit); the sweetener (white sugar or honey) and the fruit quantity (two doses). For each liquor, pH, total acidity, dry soluble solids content, dry extract, alcoholic strength, reducing sugars, colour intensity, methanol content, acetaldehyde and fusel alcohols were determined. Sensory tests were carried out with a trained panel. The three factors studied significantly influenced the physico-chemical features of the liquors, being the quantity of fruit the most discriminating factor, except for the volatile compounds which were mainly influenced by the distillate. As regards the sensory analysis, it was found that the most appreciated liquor was that prepared with wine spirit, sugar and a lower dose of blueberry, and the less appreciated formulation was the one made with grape marc spirit, honey and a lower quantity of blueberry. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

  16. Loneliness in Early Adolescence: Friendship Quantity, Friendship Quality, and Dyadic Processes.

    Science.gov (United States)

    Lodder, Gerine M A; Scholte, Ron H J; Goossens, Luc; Verhagen, Maaike

    2017-01-01

    Friendship quantity and quality are related to adolescent loneliness, but the exact link between these constructs is not well understood. The present study aimed to examine whether adolescents' perception of friendship quantity and quality, and the perceptions of their peers, were related to loneliness. We examined the relation between loneliness and the number of unilateral and reciprocal friendships and compared the views of best friendship quality. Overall, 1,172 Dutch adolescents (49.1% male, M age = 12.81, SD = .43) nominated their friends and rated their friendship quality. Friendship quantity was measured using sociometrics to distinguish reciprocated and unilateral (i.e., one-sided) friendships. The analyses indicated that loneliness was related to fewer reciprocal and unilateral-received friendships (i.e., the adolescent received a friendship nomination but did not reciprocate that nomination) and a lower quality of best friendship. Actor-partner interdependence analyses revealed that adolescents' loneliness was related to a less positive evaluation of their friendship, as reported by adolescents themselves (i.e., a significant actor effect) but not by their friends (i.e., nonsignificant partner effect). These findings (a) indicate that loneliness is negatively related to the number of friends adolescents have, as perceived by themselves and their peers and (b) suggest that, once a friendship is established, lonely adolescents may interpret the friendship quality less positively compared to their friends. Implications of these findings for our current understanding of adolescent loneliness are discussed, and suggestions for future research are outlined.

  17. Quantity and quality benefits of in-service invasive cleaning of trunk mains

    Science.gov (United States)

    Sunny, Iftekhar; Husband, Stewart; Drake, Nick; Mckenzie, Kevan; Boxall, Joby

    2017-07-01

    Trunk mains are high risk critical infrastructure where poor performance can impact on large numbers of customers. Both quantity (e.g. hydraulic capacity) and quality (e.g. discolouration) of trunk main performance are affected by asset deterioration in the form of particle accumulation at the pipe wall. Trunk main cleaning techniques are therefore desirable to remove such material. However, little is quantified regarding the efficacy of different maintenance interventions or longer-term changes following such cleaning. This paper presents an assessment of quantity and quality performance of a trunk main system pre, post and for 12 months following cleaning using pigging with ice slurry. Hydraulic calibration showed a 7 times roughness height reduction after ice slurry pigging, evidencing substantially improved hydraulic capacity and reduced headloss. Turbidity response due to carefully imposed shear stress increase remained significant after the cleaning intervention, showing that relatively loose material had not been fully removed from the pipe wall. Overall the results demonstrate that cleaning by pigging with ice slurry can be beneficial for quantity performance, but care and further assessment may be necessary to realise the full quality benefits.

  18. Quantity and quality benefits of in-service invasive cleaning of trunk mains

    Directory of Open Access Journals (Sweden)

    I. Sunny

    2017-07-01

    Full Text Available Trunk mains are high risk critical infrastructure where poor performance can impact on large numbers of customers. Both quantity (e.g. hydraulic capacity and quality (e.g. discolouration of trunk main performance are affected by asset deterioration in the form of particle accumulation at the pipe wall. Trunk main cleaning techniques are therefore desirable to remove such material. However, little is quantified regarding the efficacy of different maintenance interventions or longer-term changes following such cleaning. This paper presents an assessment of quantity and quality performance of a trunk main system pre, post and for 12 months following cleaning using pigging with ice slurry. Hydraulic calibration showed a 7 times roughness height reduction after ice slurry pigging, evidencing substantially improved hydraulic capacity and reduced headloss. Turbidity response due to carefully imposed shear stress increase remained significant after the cleaning intervention, showing that relatively loose material had not been fully removed from the pipe wall. Overall the results demonstrate that cleaning by pigging with ice slurry can be beneficial for quantity performance, but care and further assessment may be necessary to realise the full quality benefits.

  19. The economics of water reuse and implications for joint water quality-quantity management

    Science.gov (United States)

    Kuwayama, Y.

    2015-12-01

    Traditionally, economists have treated the management of water quality and water quantity as separate problems. However, there are some water management issues for which economic analysis requires the simultaneous consideration of water quality and quantity policies and outcomes. Water reuse, which has expanded significantly over the last several decades, is one of these issues. Analyzing the cost effectiveness and social welfare outcomes of adopting water reuse requires a joint water quality-quantity optimization framework because, at its most basic level, water reuse requires decision makers to consider (a) its potential for alleviating water scarcity, (b) the quality to which the water should be treated prior to reuse, and (c) the benefits of discharging less wastewater into the environment. In this project, we develop a theoretical model of water reuse management to illustrate how the availability of water reuse technologies and practices can lead to a departure from established rules in the water resource economics literature for the optimal allocation of freshwater and water pollution abatement. We also conduct an econometric analysis of a unique dataset of county-level water reuse from the state of Florida over the seventeen-year period between 1996 and 2012 in order to determine whether water quality or scarcity concerns drive greater adoption of water reuse practices.

  20. Effect of Temperature and Process on Quantity and Composition of Laboratory-generated Bitumen Emissions.

    Science.gov (United States)

    Bolliet, Christophe; Kriech, Anthony J; Juery, Catherine; Vaissiere, Mathieu; Brinton, Michael A; Osborn, Linda V

    2015-01-01

    In this study we investigated the impact of temperature on emissions as related to various bitumen applications and processes used in commercial products. Bitumen emissions are very complex and can be influenced in quantity and composition by differences in crude source, refining processes, application temperature, and work practices. This study provided a controlled laboratory environment to study five bitumen test materials from three European refineries; three paving grade, one used for primarily roofing and some paving applications, and one oxidized industrial specialty bitumen. Emissions were generated at temperatures between 140°C and 230°C based on typical application temperatures of each product. Emissions were characterized by aerodynamic particle size, total organic matter (TOM), simulated distillation, 40 individual PACs, and fluorescence (FL-PACs) spectroscopy. Results showed that composition of bitumen emissions is influenced by temperature under studied experimental conditions. A distinction between the oxidized bitumen with flux oil (industrial specialty bitumen) and the remaining bitumens was observed. Under typical temperatures used for paving (150°C-170°C), the TOM and PAC concentrations in the emissions were low. However, bitumen with flux oil produced significantly higher emissions at 230°C, laden with high levels of PACs. Flux oil in this bitumen mixture enhanced release of higher boiling-ranged compounds during application conditions. At 200°C and below, concentrations of 4-6 ring PACs were ≤6.51 μg/m(3) for all test materials, even when flux oil was used. Trends learned about emission temperature-process relationships from this study can be used to guide industry decisions to reduce worker exposure during processing and application of hot bitumen.

  1. Discussion on concepts for radiological dosimetric quantities in the Japan Health Physics Society

    International Nuclear Information System (INIS)

    Takahashi, Fumiaki; Oda, Keiji

    2007-01-01

    Many dosimetric quantities have been used for radiation protection purpose. The International Commission on Radiological Protection (ICRP) has recommended protection quantities and the International Commission on Radiation Units and Measurements (ICRU) has introduced operational quantities to provide a reasonable estimate of the protection quantities. Enthusiastic discussions are continuously made on the issues of the dosimetric quantities, such as basic biological data for the definition of these quantities and applicability of the quantities to actual radiation protection practice. At the moment, some changes are being proposed concerning dosimetric quantities in the draft recommendations of ICRP, opened for consultation in recent years. Thus, the Japan Health Physics Society (JHPS) established the Expert Committee on concepts of Dosimetric Quantities used in radiological protection (ECDQ) in April 2005 to reviewed and discuss issues in the dosimetric quantities. (author)

  2. Inventory simulation tools: Separating nuclide contributions to radiological quantities

    Science.gov (United States)

    Gilbert, Mark R.; Fleming, Michael; Sublet, Jean-Christophe

    2017-09-01

    The activation response of a material is a primary factor considered when evaluating its suitability for a nuclear application. Various radiological quantities, such as total (becquerel) activity, decay heat, and γ dose, can be readily predicted via inventory simulations, which numerically evolve in time the composition of a material under exposure to neutron irradiation. However, the resulting data sets can be very complex, often necessarily resulting in an over-simplification of the results - most commonly by just considering total response metrics. A number of different techniques for disseminating more completely the vast amount of data output from, in particular, the FISPACT-II inventory code system, including importance diagrams, nuclide maps, and primary knock-on atom (PKA) spectra, have been developed and used in scoping studies to produce database reports for the periodic table of elements. This paper introduces the latest addition to this arsenal - standardised and automated plotting of the time evolution in a radiological quantity for a given material separated by contributions from dominant radionuclides. Examples for relevant materials under predicted fusion reactor conditions, and for bench-marking studies against decay-heat measurements, demonstrate the usefulness and power of these radionuclide-separated activation plots. Note to the reader: the pdf file has been changed on September 22, 2017.

  3. Inventory simulation tools: Separating nuclide contributions to radiological quantities

    Directory of Open Access Journals (Sweden)

    Gilbert Mark R.

    2017-01-01

    Full Text Available The activation response of a material is a primary factor considered when evaluating its suitability for a nuclear application. Various radiological quantities, such as total (becquerel activity, decay heat, and γ dose, can be readily predicted via inventory simulations, which numerically evolve in time the composition of a material under exposure to neutron irradiation. However, the resulting data sets can be very complex, often necessarily resulting in an over-simplification of the results – most commonly by just considering total response metrics. A number of different techniques for disseminating more completely the vast amount of data output from, in particular, the FISPACT-II inventory code system, including importance diagrams, nuclide maps, and primary knock-on atom (PKA spectra, have been developed and used in scoping studies to produce database reports for the periodic table of elements. This paper introduces the latest addition to this arsenal – standardised and automated plotting of the time evolution in a radiological quantity for a given material separated by contributions from dominant radionuclides. Examples for relevant materials under predicted fusion reactor conditions, and for bench-marking studies against decay-heat measurements, demonstrate the usefulness and power of these radionuclide-separated activation plots.

  4. Peer Assessment for Construction Management and Quantity Surveying Students

    Directory of Open Access Journals (Sweden)

    Patricia McLaughlin

    2012-11-01

    Full Text Available Students undertaking the Bachelor of ConstructionManagement degree course at RMIT University, Melbourne,qualify for registration with the Australian Institute ofQuantity Surveyors (AIQS and the Australian Institute ofBuilding (AIB upon graduation. Over the past decade thedegree course has been constantly upgraded and altered inline with recommendations from professional bodies such asthese and other industry partners. In 1994 the Departmentof Building and Construction Economics re-assesseda range of subjects including the first year technologysubjects. Out of the review a problem-based integratedlearning unit was developed and tested. This unit has nowbeen in place for ten years.Quantity surveying and construction management likemost other professions in the construction industryrequire teamwork and advanced consultation skills. Theseskills may be learnt through experience but there isconsiderable evidence that these skills can be taught in theundergraduate years. Therefore in line with team-basedapproaches used in industry and professional constructionsettings, this year a new assessment model - peerassessment - will be applied to the problem-based learningunit. This paper describes the procedures and processesused to introduce the change and examines the theoreticalbase upon which the model was developed.

  5. Determinants of procurement strategy for construction works: quantity surveyors’ perspectives

    Directory of Open Access Journals (Sweden)

    Olanrewaju AbdulLateef

    2016-01-01

    Full Text Available The selection of the ‘appropriate’ procurement strategy is a prerequisite to the success or failure of a construction project. This paper investigates the factors determining the selection of appropriate procurement strategy for construction works in Nigeria. Data for the study was collected through an online survey questionnaire. The survey administration involves only quantity surveyors. Quantity surveyors were targeted because they advise clients and other stakeholders on procurement and contractual issues on construction works. A total of 33 usable responses were received and analysed for this study. On the basis of the results, it is concluded that the selection of procurement strategies for construction depend on complex interrelated factors. The study could not detect a particular factor or few factors responsible for a procurement strategy selection. The findings of this study is useful because it argues that the construction sector needs to broaden its considerations on the procurement strategy’s determinants rather than focusing solely on the client’s type and nature of projects as is often cited. Future research could segment these factors in terms of class of construction works or increase the sample size, which might lead to different findings.

  6. Estimation of Waste Quantities Using DeCAT-Pro

    Energy Technology Data Exchange (ETDEWEB)

    Yun, Taesik; Jung, Hyejin; Oh, Jaeyoung; Kim, Younggook [KHNP CRI, Daejeon (Korea, Republic of)

    2016-10-15

    The D and D (Dismantling and Decontamination) is scheduled to get started in June 2022 elapsing five years of cooling spent fuels down. The final site status is postulated as Brown Field and tentative DCGL of less than 0.1 mSv per year to evaluate waste quantities in a conservative manner. The decommissioning strategy was determined the immediate decommissioning whose whole period would be taken for approximately 15 years; pre-decommissioning for two years, spent fuel cool-down for five years, D and D for six years, site remediation for two years. The assumption to dismantle the underground facilities including SSCs is to one meter beneath the ground level and the other facilities remain intact. In addition, non-radioactive concrete wastes would be used to landfill gaps of the remaining facilities. Although there are many assumptions we applied, the methodologies developed and the data produced by this research will play a meaningful role as a good starting point for the Kori-1 decommissioning after its shutdown to logically and reasonably estimate the waste quantity. However it is clear that tenacious efforts should be taken to successfully perform the decommissioning project.

  7. The orientation distribution of tunneling-related quantities

    Science.gov (United States)

    Seif, W. M.; Refaie, A. I.; Botros, M. M.

    2018-03-01

    In the nuclear tunneling processes involving deformed nuclei, most of the tunneling-related quantities depend on the relative orientations of the participating nuclei. In the presence of different multipole deformations, we study the variation of a few relevant quantities for the α-decay and the sub-barrier fusion processes, in an orientation degree of freedom. The knocking frequency and the penetration probability are evaluated within the Wentzel-Kramers-Brillouin approximation. The interaction potential is calculated with Skyrme-type nucleon-nucleon interaction. We found that the width of the potential pocket, the Coulomb barrier radius, the penetration probability, the α-decay width, and the fusion cross-section follow consistently the orientation-angle variation of the radius of the deformed nucleus. The orientation distribution patterns of the pocket width, the barrier radius, the logarithms of the penetrability, the decay width, and the fusion cross-section are found to be highly analogous to pattern of the deformed-nucleus radius. The curve patterns of the orientation angle distributions of the internal pocket depth, the Coulomb barrier height and width, as well as the knocking frequency simulate inversely the variation of the deformed nucleus radius. The predicted orientation behaviors will be of a special interest in predicting the optimum orientations for the tunneling processes.

  8. Highway route controlled quantity shipment routing reports - An overview

    International Nuclear Information System (INIS)

    Cashwell, J.W.; Welles, B.W.; Welch, M.J.

    1989-01-01

    US Department of Transportation (DOT) regulations require a postnotification report from the shipper for all shipments of radioactive materials categorized as a Highway Route Controlled Quantity. These postnotification reports, filed in compliance with 49 CFR 172.203(d), have been compiled by the DOT in a database known as the Radioactive Materials Routing Report (RAMRT) since 1982. The data were sorted by each of its elements to establish historical records and trends of Highway Route Controlled Quantity shipments from 1982 through 1987. Approximately 1520 records in the RAMRT database were compiled for this analysis. Approximately half of the shipments reported for the study period were from the US Department of Energy (DOE) and its contractors, with the others being commercial movements. Two DOE installations, EG and G Idaho and Oak Ridge, accounted for nearly half of the DOE activities. Similarly, almost half of the commercial movements were reported by two vendors, Nuclear Assurance Corporation and Transnuclear, Incorporated. Spent fuel from power and research reactors accounted for approximately half of all shipments

  9. Improvement of job satisfaction and organisational commitment through work group identification: an examination of the quantity surveyors in Hong Kong

    Directory of Open Access Journals (Sweden)

    Wai Yee Betty Chiu

    2013-09-01

    Full Text Available Though extant literatures in other sectors indicatethat job satisfaction and organizational commitment are important fordetermining individual and organisational outcomes, limited related researchhas been conducted amongst quantity surveyors in Hong Kong. Given cooperativeworking arrangement in the quantity surveying profession, work groupidentification is regarded as an important antecedent for determining jobsatisfaction and organisational commitment. The aim of this study is to examinewhether work group identification improves job satisfaction and organisationalcommitment. A questionnaire survey is conducted to collect data from quantitysurveyors working in private sector. A total of 71 valid responses are obtainedfrom 509 contacted quantity surveyors in Hong Kong. Bivariate correlation andmultiple regression analyses are performed to find the significance ofrelationships among the variables. Data analysis results support mosthypotheses. Work group identification is found to have significant positiveeffect on job satisfaction, affective and normative commitment. The finding isa bold step for quantity surveying companies to improve their quantity surveyors’job satisfaction and commitment level. The role of other contextual and organisationalfactors on job satisfaction and organisational commitment needs to becomplemented for future research.

  10. Detecting Novelty and Significance

    Science.gov (United States)

    Ferrari, Vera; Bradley, Margaret M.; Codispoti, Maurizio; Lang, Peter J.

    2013-01-01

    Studies of cognition often use an “oddball” paradigm to study effects of stimulus novelty and significance on information processing. However, an oddball tends to be perceptually more novel than the standard, repeated stimulus as well as more relevant to the ongoing task, making it difficult to disentangle effects due to perceptual novelty and stimulus significance. In the current study, effects of perceptual novelty and significance on ERPs were assessed in a passive viewing context by presenting repeated and novel pictures (natural scenes) that either signaled significant information regarding the current context or not. A fronto-central N2 component was primarily affected by perceptual novelty, whereas a centro-parietal P3 component was modulated by both stimulus significance and novelty. The data support an interpretation that the N2 reflects perceptual fluency and is attenuated when a current stimulus matches an active memory representation and that the amplitude of the P3 reflects stimulus meaning and significance. PMID:19400680

  11. Significant NRC Enforcement Actions

    Data.gov (United States)

    Nuclear Regulatory Commission — This dataset provides a list of Nuclear Regulartory Commission (NRC) issued significant enforcement actions. These actions, referred to as "escalated", are issued by...

  12. The Significance of Science

    Science.gov (United States)

    Pielke, R.

    2002-05-01

    Whether global warming, terrestrial carbon sinks, ecosystem functioning, genetically modified organisms, cloning, vaccination or chemicals in the environment, science is increasingly the battlefield on which political advocates, not least lawyers and commercial interests, manipulate `facts' to their preferred direction, which fosters the politicization of science. Debate putatively over science increasingly relies on tactics such as ad hominem attacks and criticism of process (for example, peer review or sources of funding), through paid advertisements, press releases and other publicity campaigns. As political battles are waged through `science', many scientists are willing to adopt tactics of demagoguery and character assassination as well as, or even instead of, reasoned argument, as in aspects of debate over genetically modified crops or global warming. Science is becoming yet another playing field for power politics, complete with the trappings of media spin and a win-at-all-costs attitude. Sadly, much of what science can offer policymakers, and hence society, is lost. This talk will use cases from the atmospheric sciences as points of departure to explore the politicization of science from several perspectives and address questions such as: Is it a problem? For whom and what outcomes? What are the alternatives to business-as-usual?

  13. MICROMICETES QUANTITY AND BIOMASS IN TECHNOGENIC AND NATURAL SOILS

    Directory of Open Access Journals (Sweden)

    Korinovskaya Olga Nikolaevna

    2014-08-01

    Full Text Available It is shown that in edaphotopes around of freight checkpoint of CJSC «Krivorozhskiy Surikovyy Zavod», ore-enrichment factory and fresh-inwashed pool of tailings dam of PJSC «Northern Iron Ore Enrichment Works» there is an increase of heavy metals mobile forms (which are the most dangerous for microorganisms, plants, animals and human: for iron in 310; for zinc - in 4,3-6,5; for lead - in 3.2-5.7; for cadmium - in 5,6-9,8; for copper – 6,8-66,5 and for nickel - in 9 times as compared to zonal soil. Whereas in soils of CJSC «Krivorozhskiy Surikovyy Zavod» sanitary protection zone number of copper, nickel, lead, cadmium and zinc mobile forms exceeded the control values in 2,4-6,6 times. For the first time the features of soil microscopic fungi seasonal dynamics of quantity in industrial disturbed soils of Kryvorizhzhya compared to zonal soil (chernozem usual were registered. Changes in fungal mycelium length and biomass, its spore’s amount and biomass in edaphotopes of ore-enrichment and chemical enterprises and of common chernozem are also presented. It is shown that in edaphotopes of heavy contamination areas of «Krivorozhskiy Surikovyy Zavod» and of «Northern Iron Ore Enrichment Works» in spring, summer, and autumn there was decrease of microscopic fungi quantity in 4-10 times, moreover in tehnozems of «Northern Iron Ore Enrichment Works» fresh-inwashed pool of tailings dam their amount reduces in more than 100 times, compared with common chernozem. In low contamination area of «Krivorozhskiy Surikovyy Zavod» their quantity decreases in 2 times. Also in heavy contamination areas of chemical and ore-enrichment enterprises there is strong decrease in the length of fungal mycelium in 2.7-4.2 times, its biomass in 2,6-4,5 times, the spores amount - in 4,5-7,7 times and their biomass - in 10,5-21 times compared to the natural soil, which could be explained by high contents of toxicants. While in the sanitary protection zone of the

  14. EIA new releases

    International Nuclear Information System (INIS)

    1994-09-01

    This report is a compliation of news releases from the Energy Information Administration. The september-october report includes articles on energy conservation, energy consumption in commercial buildings, and a short term energy model for a personal computer

  15. The quantity time relation in the ionizing radiations

    Science.gov (United States)

    Jordão, B. O.; Quaresma, D. S.; Peixoto, J. G. P.

    2018-03-01

    The metrology area has taken a step forward with regard to the uncertainty calculation. This mathematical tool used in laboratories is essential to ensure that the values resulting from a measurement are reliable. For this to be possible, all equipment used in a measurement process must be reliable and, above all, traceable to the international metrology system. We propose to present in this work: (i) the development and calibration of a microcontrolled time device with a resolution of 1x10-4 s, in order to characterize the time greatness and make it re-producible; (ii) the calibration of the quartz clock present in a computer present in the dosimetry laboratories; (iii) a more in-depth study of the influence of time quantity on calibrations of instruments used in the area of radiological protection, diagnostic radiology and radiotherapy, with measurements performed on the Kerma magnitude in air or its rate.

  16. Quantity and structure of word knowledge across adulthood.

    Science.gov (United States)

    Salthouse, Timothy A

    2014-09-01

    Cross-sectional and longitudinal data from moderately large samples of healthy adults confirmed prior findings of age-related declines in measures of the quantity of word knowledge beginning around age 65. Additional analyses were carried out to investigate the interrelations of different types of vocabulary knowledge at various periods in adulthood. Although the organizational structures were similar in adults of different ages, scores on tests with different formats had weaker relations to a higher-order vocabulary construct beginning when adults were in their 60's. The within-person dispersion among different vocabulary test scores was also greater after about 65 years of age. The discovery of quantitative decreases in amount of knowledge occurring at about the same age as qualitative shifts in the structure of knowledge raises the possibility that the two types of changes may be causally linked.

  17. Synthesis of pure iron magnetic nanoparticles in large quantity

    International Nuclear Information System (INIS)

    Tiwary, C S; Kashyap, S; Chattopadhyay, K; Biswas, K

    2013-01-01

    Free nanoparticles of iron (Fe) and their colloids with high saturation magnetization are in demand for medical and microfluidic applications. However, the oxide layer that forms during processing has made such synthesis a formidable challenge. Lowering the synthesis temperature decreases rate of oxidation and hence provides a new way of producing pure metallic nanoparticles prone to oxidation in bulk amount (large quantity). In this paper we have proposed a methodology that is designed with the knowledge of thermodynamic imperatives of oxidation to obtain almost oxygen-free iron nanoparticles, with or without any organic capping by controlled milling at low temperatures in a specially designed high-energy ball mill with the possibility of bulk production. The particles can be ultrasonicated to produce colloids and can be bio-capped to produce transparent solution. The magnetic properties of these nanoparticles confirm their superiority for possible biomedical and other applications. (paper)

  18. Protection of groundwater resources quality and quantity in mining areas

    International Nuclear Information System (INIS)

    Grmela, A.

    1997-01-01

    This contribution is devoted to the problems of the impact of land subsidence from coal and other mining systems on underground and surface waters, particularly in relation to the possible influence on quality and quantity of pumped waters for public or individual supply. It determines features of permanent and time-limited changes of hydrogeological structure and effectiveness of measures for their minimization (classification of sources from the point of view of protection, delineation of protection zones for water resources, monitoring of effectiveness of measures). Case studies are presented for examples from the Czech part of Upper Silesian Basin - catchment area Doubrava-Spluchov, Karvina-Stare Mesto, Ostrava-Nove Ves, and Dubi, Darkov Spa. Attention is focused on problems of delimitation of protection zones in undermined areas in respect to the new proposal of the Appendix to Water Law. 8 refs., 2 figs

  19. Symbol addition by monkeys provides evidence for normalized quantity coding

    Science.gov (United States)

    Livingstone, Margaret S.; Pettine, Warren W.; Srihasam, Krishna; Moore, Brandon; Morocz, Istvan A.; Lee, Daeyeol

    2014-01-01

    Weber’s law can be explained either by a compressive scaling of sensory response with stimulus magnitude or by a proportional scaling of response variability. These two mechanisms can be distinguished by asking how quantities are added or subtracted. We trained Rhesus monkeys to associate 26 distinct symbols with 0–25 drops of reward, and then tested how they combine, or add, symbolically represented reward magnitude. We found that they could combine symbolically represented magnitudes, and they transferred this ability to a novel symbol set, indicating that they were performing a calculation, not just memorizing the value of each combination. The way they combined pairs of symbols indicated neither a linear nor a compressed scale, but rather a dynamically shifting, relative scaling. PMID:24753600

  20. ANALYZER OF QUANTITY AND QUALITY OF THE ELECTRIC POWER

    Directory of Open Access Journals (Sweden)

    A. I. Semilyak

    2013-01-01

    Full Text Available One of the activities of the research center for “Energy Saving Technologies and Smart Metering in Electrical Power Engineering" is research work on the use of electronic devices and systems of intelligent power distribution, produced by Analog Devices and equipped with the accurate energy consumption measurement feature. The article focuses on the development of the analyzer of quantity and quality of electric energy.The main part of the analyzer is a metering IC by Analog Devices ADE7878, designed for use in commercial and industrial smart electricity meters. Such counters measure the amount of consumed or produced electric energy with high accuracy and have the means of remote meter reading.

  1. The quantity time relation in the ionizing radiations

    Energy Technology Data Exchange (ETDEWEB)

    Jordão, Bruno; Quaresma, Daniel, E-mail: bjordan@on.br [Observatorio Nacional (LPTF/ON), Rio de Janeiro, RJ (Brazil). Laboratório Primário de Tempo e Frequência; Peixoto, José Guilherme P. [Instituto de Radioproteção e Dosimetria (LNMRI/IRD/CNEN-RJ), Rio de Janeiro, RJ (Brazil). Laboratório Nacional de Metrologia das Radiações Ionizantes

    2017-07-01

    The area of metrology has taken a step forward with regard to the calculation of uncertainty. This mathematical tool used in laboratories is essential to ensure that the values resulting from a measurement are reliable. For this to be possible, all equipment used in a measurement process must be reliable and, above all, traceable to the international metrology system. We propose to present in this work: (1) the development and calibration of a microcontrolled time device with a resolution of 1 x 10{sup -4} s, in order to characterize the time greatness and make it reproducible; (2) the calibration of the quartz clock present in a computer present in the dosimetry laboratories; (3) a more in-depth study of the influence of time quantity on calibrations of instruments used in the area of radiological protection, diagnostic radiology and radiotherapy, with measurements performed on the Kerma magnitude in air or its rate. (author)

  2. The quantity time relation in the ionizing radiations

    International Nuclear Information System (INIS)

    Jordão, Bruno; Quaresma, Daniel; Peixoto, José Guilherme P.

    2017-01-01

    The area of metrology has taken a step forward with regard to the calculation of uncertainty. This mathematical tool used in laboratories is essential to ensure that the values resulting from a measurement are reliable. For this to be possible, all equipment used in a measurement process must be reliable and, above all, traceable to the international metrology system. We propose to present in this work: (1) the development and calibration of a microcontrolled time device with a resolution of 1 x 10 -4 s, in order to characterize the time greatness and make it reproducible; (2) the calibration of the quartz clock present in a computer present in the dosimetry laboratories; (3) a more in-depth study of the influence of time quantity on calibrations of instruments used in the area of radiological protection, diagnostic radiology and radiotherapy, with measurements performed on the Kerma magnitude in air or its rate. (author)

  3. Measuring Radionuclides in the environment: radiological quantities and sampling designs

    International Nuclear Information System (INIS)

    Voigt, G.

    1998-10-01

    One aim of the workshop was to support and provide an ICRU report committee (International Union of Radiation Units) with actual information on techniques, data and knowledge of modern radioecology when radionuclides are to be measured in the environment. It has been increasingly recognised that some studies in radioecology, especially those involving both field sampling and laboratory measurements, have not paid adequate attention to the problem of obtaining representative, unbiased samples. This can greatly affect the quality of scientific interpretation, and the ability to manage the environment. Further, as the discipline of radioecology has developed, it has seen a growth in the numbers of quantities and units used, some of which are ill-defined and which are non-standardised. (orig.)

  4. Sellafield (release of radioactivity)

    Energy Technology Data Exchange (ETDEWEB)

    Cunningham, J; Goodlad, A; Morris, M

    1986-02-06

    A government statement is reported, about the release of plutonium nitrate at the Sellafield site of British Nuclear Fuels plc on 5 February 1986. Matters raised included: details of accident; personnel monitoring; whether radioactive material was released from the site; need for public acceptance of BNFL activities; whether plant should be closed; need to reduce level of radioactive effluent; number of incidents at the plant.

  5. The use of averages and other summation quantities in the testing of evaluated fission product yield and decay data. Applications to ENDF/B(IV)

    International Nuclear Information System (INIS)

    Walker, W.H.

    1976-01-01

    Averages of some fission product properties can be obtained by multiplying the fission product yield for each fission product by the value of the property (e.g. mass, atomic number, mass defect) for that fission product and summing all significant contributions. These averages can be used to test the reliability of the yield set or provide useful data for reactor calculations. The report gives the derivation of these averages and discusses their application using the ENDF/B(IV) fission product library. The following quantities are treated here: the number of fission products per fission ΣYsub(i); the average mass number and the average number of neutrons per fission; the average atomic number of the stable fission products and the average number of β-decays per fission; the average mass defect of the stable fission products and the total energy release per fission; the average decay energy per fission (beta, gamma and anti-neutrino); the average β-decay energy per fission; individual and group-averaged delayed neutron emission; the total yield for each fission product element. Wherever it is meaningful to do so, a sum is subdivided into its light and heavy mass components. The most significant differences between calculated values based on ENDF/B(IV) and measurements are the β and γ decay energies for 235 U thermal fission and delayed neutron yields for other fissile nuclides, most notably 238 U. (author)

  6. Biologically Weighted Quantities in Radiotherapy: an EMRP Joint Research Project

    Directory of Open Access Journals (Sweden)

    Rabus Hans

    2014-01-01

    Full Text Available Funded within the European Metrology Research Programme (EMRP [1], the joint research project “Biologically weighted quantities in radiotherapy” (BioQuaRT [2] aims to develop measurement and simulation techniques for determining the physical properties of ionising particle tracks on different length scales (about 2 nm to 10 μm, and to investigate the correlation of these track structure characteristics with the biological effects of radiation at the cellular level. Work package 1 develops micro-calorimeter prototypes for the direct measurement of lineal energy and will characterise their response for different ion beams by experiment and modelling. Work package 2 develops techniques to measure particle track structure on different length scales in the nanometre range as well as a measurement device integrating a silicon microdosimeter and a nanodosimeter. Work package 3 investigates the indirect effects of radiation based on probes for quantifying particular radical and reactive oxygen species (ROS. Work package 4 focuses on the biological aspects of radiation damage and will produce data on initial DNA damage and late effects for radiotherapy beams of different qualities. Work package 5 provides evaluated data sets of DNA cross-sections and develops a multi-scale model to address microscopic and nanometric track structure properties. The project consortium includes three linked researchers holding so-called Researcher Excellence Grants, who carry out ancillary investigations such as developing and benchmarking a new biophysical model for induction of early radiation damage and developing methods for the translation of quantities derived from particle track structure to clinical applications in ion beam therapy.

  7. Is the dose equivalent index a quantity to be measured

    International Nuclear Information System (INIS)

    Wagner, S.R.

    1980-01-01

    ICRP introduced the concept of Effective Dose Equivalent H(sub)E and fixed the basic limits of radiation exposure in terms of H(sub)I. As H(sub)E cannot be measured, ICRP stated that with external exposure to penetrating radiation the limitation of the Dose Equivalent Index H(sub)I would afford at least as good a level of protection. However, difficulties arise in measuring H(sub)I and in calibrating instruments in terms of H(sub)I, since the height and location of the dose equivalent maximum in the sphere which is the phantom used in the definition of H(sub)I, depend on the energy and the angular distribution of the incident radiation. That is, H(sub)I is not an additive quantity relative to the partial H(sub)I(sub)i-values of the different energy and angular components. Hence, 1) the distribution of dose equivalent in the sphere must be measured in full for a determination of H(sub)I, and 2) it is not possible to calibrate an instrument which does not exhibit the scattering and absorption properties of the sphere, consistently for arbitrary radiation fields in terms of H(sub)I. Thus the calibration in an unidirectional beam would infer an uncertainty which may amount to a factor of up to 4. This would hardly be tolerable as a base for radiation protection provisions. An alternative is to introduce operational quantities which are additive, e.g. 1) the sum of maxima of the dose equivalent distributions in the sphere produced by different radiation components, and 2) the mean dose equivalent in the sphere. Their relation to H(sub)E for different types of radiation and consequences on secondary limits are discussed. (H.K.)

  8. [Application of target restoration space quantity and quantitative relation in precise esthetic prosthodontics].

    Science.gov (United States)

    Haiyang, Yu; Tian, Luo

    2016-06-01

    Target restoration space (TRS) is the most precise space required for designing optimal prosthesis. TRS consists of an internal or external tooth space to confirm the esthetics and function of the final restoration. Therefore, assisted with quantitive analysis transfer, TRS quantitative analysis is a significant improvement for minimum tooth preparation. This article presents TRS quantity-related measurement, analysis, transfer, and internal relevance of three TR. classifications. Results reveal the close bond between precision and minimally invasive treatment. This study can be used to improve the comprehension and execution of precise esthetic prosthodontics.

  9. Procurement-distribution model for perishable items with quantity discounts incorporating freight policies under fuzzy environment

    Directory of Open Access Journals (Sweden)

    Makkar Sandhya

    2013-01-01

    Full Text Available A significant issue of the supply chain problem is how to integrate different entities. Managing supply chain is a difficult task because of complex integrations, especially when the products are perishable in nature. Little attention has been paid on ordering specific perishable products jointly in uncertain environment with multiple sources and multiple destinations. In this article, we propose a supply chain coordination model through quantity and freight discount policy for perishable products under uncertain cost and demand information. A case is provided to validate the procedure.

  10. Study of dosimetric quantities and image quality in pediatric examinations of chest and abdomen computed tomography

    International Nuclear Information System (INIS)

    Jornada, Tiago da Silva

    2013-01-01

    This work had the objective to achieve the knowledge of the dosimetric quantities related to chest and abdomen computed tomography (CT) examinations of pediatric patients, in Belo Horizonte city. The reason of this work is based on the fact that the probability of health detriment in children, which it may be caused by radiation, is higher than in adults. Besides, although in many countries the knowledge and control of patient doses is a normal procedure, this safety culture does not exist in Brazil. Another objective of this work was to compare the dosimetric quantity values with the Diagnostic Reference Levels (DRLs); when it was needed, an optimization process was applied and the quality of the diagnostic image obtained with the optimized technical parameters was analyzed. This study was carried out in five hospitals, where the weighted air kerma index (Cw), the volumetric air kerma index (Cvol), the air kerma - length product (PKL,CT), the Effective Dose (E) and the Normalized Effective Dose (En) were determined; three methods were adopted for measurements: the ionization chamber inside a chest pediatric phantom, radiochromic films and the CT-EXPO software. The optimization process was applied to a single hospital through variations in the current (mA) and voltage (kV) of the x-ray tube for the protocols used for abdomen CT examinations. The analysis of the quality of the diagnostic image was done by Normal Distribution and ROC analysis; spatial resolution analysis was used through MTF determination and the noise level was judged in terms quantitative and qualitative. Results of the dosimetric quantities showed that they significantly differed between single-slice and multi-slice tomography units, but their values were always below the recommended DRLs. The optimized values of the dosimetric quantities obtained after the optimization process showed that it was possible to reduce the radiation exposure of pediatric patient without losing the image quality

  11. The influence of using anticoagulants (EDTA and citrate acid 3.8% toward the quantity of Platelet Rich Plasma (PRP

    Directory of Open Access Journals (Sweden)

    Lilies Anggarwati Astuti

    2016-06-01

    Full Text Available Platelet Rich Plasma (PRP is a blood concentrate that has a thrombocytes concentration several time higher than normal concentration of thrombocytes in normal human blood. PRP is a promising alternative to surgery with a safe and natural healing. The standard protocol for PRP preparation must be determined to get the right quantity and quality of the matrix of fibrin, leukocytes, platelets and growth factors. It could not be separated from the number of PRP produced. The use of PRP in the success of periodontal treatment would not be separated from methods to obtain it. To detect the influence of using anticoagulants (EDTA and citrate acid 3.8% toward the quantity of PRP. There are 41 subjects studied by taking 21 ml of venous blood in each of the seven tubes. Centrifugation performed twice with different speed, duration, use of anticoagulants then analyzed. This quantity between the two groups differed significantly between the PRP in EDTA group is higher 322.2 ml rather than citrate acid 3.8% group, then control group is higher 329.5 ml rather than citrate acid 3.8% group, while there is no difference between EDTA and control group. There is effect of the use of anticoagulants EDTA compared with citrate acid 3.8% in the quantity of PRP, and there was no effect using citrate acid 3.8% as anticoagulants in quantity of PRP.

  12. Fuel morphology effects on fission product release

    International Nuclear Information System (INIS)

    Osetek, D.J.; Hartwell, J.K.; Cronenberg, A.W.

    1986-01-01

    Results are presented of fission product release behavior observed during four severe fuel damage tests on bundles of UO 2 fuel rods. Transient temperatures up to fuel melting were obtained in the tests that included both rapid and slow cooldown, low and high (36 GWd/t) burnup fuel and the addition of Ag-In-Cd control rods. Release fractions of major fission product species and release rates of noble gas species are reported. Significant differences in release behavior are discussed between heatup and cooldown periods, low and high burnup fuel and long- and short-lived fission products. Explanations for the observed differences are offered that relate fuel morphology changes to the releases

  13. Intracellular sphingosine releases calcium from lysosomes.

    Science.gov (United States)

    Höglinger, Doris; Haberkant, Per; Aguilera-Romero, Auxiliadora; Riezman, Howard; Porter, Forbes D; Platt, Frances M; Galione, Antony; Schultz, Carsten

    2015-11-27

    To elucidate new functions of sphingosine (Sph), we demonstrate that the spontaneous elevation of intracellular Sph levels via caged Sph leads to a significant and transient calcium release from acidic stores that is independent of sphingosine 1-phosphate, extracellular and ER calcium levels. This photo-induced Sph-driven calcium release requires the two-pore channel 1 (TPC1) residing on endosomes and lysosomes. Further, uncaging of Sph leads to the translocation of the autophagy-relevant transcription factor EB (TFEB) to the nucleus specifically after lysosomal calcium release. We confirm that Sph accumulates in late endosomes and lysosomes of cells derived from Niemann-Pick disease type C (NPC) patients and demonstrate a greatly reduced calcium release upon Sph uncaging. We conclude that sphingosine is a positive regulator of calcium release from acidic stores and that understanding the interplay between Sph homeostasis, calcium signaling and autophagy will be crucial in developing new therapies for lipid storage disorders such as NPC.

  14. The Plinius/Colima CA-U3 test on fission-product aerosol release over a VVER-type corium pool; L'essai Plinius/Colima CA-U3 sur le relachement des aerosols de produits de fission au-dessus d'un bain de corium de type VVER

    Energy Technology Data Exchange (ETDEWEB)

    Journeau, Ch.; Piluso, P.; Correggio, P.; Godin-Jacqmin, L

    2007-07-01

    In a hypothetical case of severe accident in a PWR type VVER-440, a complex corium pool could be formed and fission products could be released. In order to study aerosols release in terms of mechanisms, kinetics, nature or quantity, and to better precise the source term of VVER-440, a series of experiments have been performed in the Colima facility and the test Colima CA-U3 has been successfully performed thanks to technological modifications to melt a prototypical corium at 2760 C degrees. Specific instrumentation has allowed us to follow the evolution of the corium melt and the release, transport and deposition of the fission products. The main conclusions are: -) there is a large release of Cr, Te, Sr, Pr and Rh (>95%w), -) there is a significant release of Fe (50%w), -) there is a small release of Ba, Ce, La, Nb, Nd and Y (<90%w), -) there is a very small release of U in proportion (<5%w) but it is one of the major released species in mass, and -) there is no release of Zr. The Colima experimental results are consistent with previous experiments on irradiated fuels except for Ba, Fe and U releases. (A.C.)

  15. Formal conditions for the significance-effect

    DEFF Research Database (Denmark)

    Thellefsen, Torkild Leo; Sørensen, Bent; Thellefsen, Martin

    2006-01-01

    The significance-effect is the right effect of meaning caused upon an interpreting mind. The right effect is understood as the right interpretation of an intended meaning caused by a sign communicated by an utterer. In the article, which is inspired by Charles S. Peirce's doctrine of signs, his s...... semeiotics and his theory of communication, we account for the formal conditions that have to be present for the release of the significance-effect....

  16. Applying nonlinear MODM model to supply chain management with quantity discount policy under complex fuzzy environment

    Directory of Open Access Journals (Sweden)

    Zhe Zhang

    2014-06-01

    Full Text Available Purpose: The aim of this paper is to deal with the supply chain management (SCM with quantity discount policy under the complex fuzzy environment, which is characterized as the bi-fuzzy variables. By taking into account the strategy and the process of decision making, a bi-fuzzy nonlinear multiple objective decision making (MODM model is presented to solve the proposed problem.Design/methodology/approach: The bi-fuzzy variables in the MODM model are transformed into the trapezoidal fuzzy variables by the DMs's degree of optimism ?1 and ?2, which are de-fuzzified by the expected value index subsequently. For solving the complex nonlinear model, a multi-objective adaptive particle swarm optimization algorithm (MO-APSO is designed as the solution method.Findings: The proposed model and algorithm are applied to a typical example of SCM problem to illustrate the effectiveness. Based on the sensitivity analysis of the results, the bi-fuzzy nonlinear MODM SCM model is proved to be sensitive to the possibility level ?1.Practical implications: The study focuses on the SCM under complex fuzzy environment in SCM, which has a great practical significance. Therefore, the bi-fuzzy MODM model and MO-APSO can be further applied in SCM problem with quantity discount policy.Originality/value: The bi-fuzzy variable is employed in the nonlinear MODM model of SCM to characterize the hybrid uncertain environment, and this work is original. In addition, the hybrid crisp approach is proposed to transferred to model to an equivalent crisp one by the DMs's degree of optimism and the expected value index. Since the MODM model consider the bi-fuzzy environment and quantity discount policy, so this paper has a great practical significance.

  17. Radiation Protection Concepts and Quantities for the Occupational Exposure to Cosmic Radiation

    International Nuclear Information System (INIS)

    Bartlett, D.T.

    1999-01-01

    For the purposes of dose limitation and dose control, the harm, or detriment, of exposure to radiation is assessed by the quantity effective dose. Effective dose is evaluated by the application of factors to the averaged absorbed dose in the organs and tissues of the body. Radiation monitoring instruments are generally calibrated in terms of the quantity ambient dose equivalent which is defined in a simple spherical phantom. The relationship of these quantities is described. Requirements for the radiation protection of aircraft crew are given in the European Union Council Directive 96/29/EURATOM. There are requirements to assess the exposure of aircraft crew, to inform them of health risks, to reduce higher doses, and to control the dose to the foetus. There are no explicit dose limits, other than a dose objective to be applied to the exposure of the foetus, and no requirements for designation of areas or classification of workers. There are significant differences between the exposure condition of aircraft crew and workers in most other industries where there is occupational exposure to radiation. There are greater ranges of radiation types and energy, and there are different dose distributions and characteristics of the working populations. However, the field intensity is predictable and, with the exception of rare solar events, there is no risk of significant unexpected exposures. Dose assessment is anticipated to be by folding staff roster information with estimates of route doses, since there is little variability of dose rate within an aircraft. Route doses, which may be either an agreed average value for a given airport pairing and aircraft type, or be flight specific, will be closely linked to measured values. Requirements as to the accuracy of dose assessment should be applied which are broadly similar to those used in individual monitoring generally. (author)

  18. The Effects of Type and Quantity of Input on Iranian EFL Learners’ Oral Language Proficiency

    Directory of Open Access Journals (Sweden)

    Zahra Hassanzadeh

    2014-05-01

    Full Text Available In the written texts on foreign language learning, a group of studies has stressed the function of learning context and learning chances for learners’ language input. The present thesis had two main goals: on the one hand, different types of input to which Iranian grade four high school EFL learners’ are exposed were looked at; on the other hand, the possible relationship between types and quantity of input and Iranian EFL learners’ oral proficiency was investigated. It was supposed that EFL learners who have access to more input will show better oral proficiency than those who do not have. Instruments used in the present study for the purpose of data collation included  PET test, researcher- made questionnaire, oral language proficiency test and face- to -face interview. Data were gathered from 50 Iranian female grade four high school foreign language learners who were selected from among 120 students whose score on PET test were +1SD from the mean score. The results of the Spearman rank –order correlation test for the types of input and oral language proficiency scores, showed that the participants’ oral proficiency score significantly correlated with the intended four sources of input including spoken (rho= 0.416, sig=0.003, written (rho= 0.364, sig=0.009, aural (rho= 0.343, sig=0.015 and visual or audio-visual types of input (rho= 0.47, sig=0.00. The findings of Spearman rank –order correlation test for the quantity of input and oral language proficiency scores also showed a significant relationship between quantity of input and oral language proficiency (rho= 0.543, sig= 0.00. The findings showed that EFL learners’ oral proficiency is significantly correlated with efficient and effective input. The findings may also suggest  answers to the question why most Iranian English learners fail to speak English fluently, which might be due to  lack of effective input. This may emphasize the importance of the types and quantity of

  19. Transient fission gas release during direct electrical heating experiments

    International Nuclear Information System (INIS)

    Fenske, G.R.; Emerson, J.E.; Savoie, F.E.

    1983-12-01

    The gas release behavior of irradiated EBR-II fuel was observed to be dependent on several factors: the presence of cladding, the retained gas content, and the energy absorbed. Fuel that retained in excess of 16 to 17 μmoles/g of fission gas underwent spallation as the cladding melted and released 22 to 45% of its retained gas, while fuel with retained gas levels below approx. 15 to 16 μmoles/g released less than approx. 9% of its gas as the cladding melted. During subsequent direct electrical heating ramps, fuel that did not spall released an additional quantity of gas (up to 4 μmoles/g), depending on the energy absorbed

  20. Savannah River release: test of the new ARAC capability

    International Nuclear Information System (INIS)

    Dickerson, M.H.

    1977-01-01

    Working jointly from opposite sides of the nation Lawrence Livermore Laboratory (LLL) and the Savannah River Laboratory (SRL) quickly assessed the consequences of an early-morning tritium release in May 1974 from the Savannah River Plant, in South Carolina. Measurements confirmed the accuracy of the LLL predictions. Due to the small quantity involved and to the release location (well within the plant confines), the release was not dangerous to the public. The emergency provided a dramatic test of procedures and capabilities of the new Atmospheric Release Advisory Capability (ARAC) center at Livermore, which was not yet operational, demonstrating the capacity for quick response, and the feasibility of real-time data acquisition and transmittal across the continent

  1. ATP Release Channels

    Directory of Open Access Journals (Sweden)

    Akiyuki Taruno

    2018-03-01

    Full Text Available Adenosine triphosphate (ATP has been well established as an important extracellular ligand of autocrine signaling, intercellular communication, and neurotransmission with numerous physiological and pathophysiological roles. In addition to the classical exocytosis, non-vesicular mechanisms of cellular ATP release have been demonstrated in many cell types. Although large and negatively charged ATP molecules cannot diffuse across the lipid bilayer of the plasma membrane, conductive ATP release from the cytosol into the extracellular space is possible through ATP-permeable channels. Such channels must possess two minimum qualifications for ATP permeation: anion permeability and a large ion-conducting pore. Currently, five groups of channels are acknowledged as ATP-release channels: connexin hemichannels, pannexin 1, calcium homeostasis modulator 1 (CALHM1, volume-regulated anion channels (VRACs, also known as volume-sensitive outwardly rectifying (VSOR anion channels, and maxi-anion channels (MACs. Recently, major breakthroughs have been made in the field by molecular identification of CALHM1 as the action potential-dependent ATP-release channel in taste bud cells, LRRC8s as components of VRACs, and SLCO2A1 as a core subunit of MACs. Here, the function and physiological roles of these five groups of ATP-release channels are summarized, along with a discussion on the future implications of understanding these channels.

  2. Significant Tsunami Events

    Science.gov (United States)

    Dunbar, P. K.; Furtney, M.; McLean, S. J.; Sweeney, A. D.

    2014-12-01

    Tsunamis have inflicted death and destruction on the coastlines of the world throughout history. The occurrence of tsunamis and the resulting effects have been collected and studied as far back as the second millennium B.C. The knowledge gained from cataloging and examining these events has led to significant changes in our understanding of tsunamis, tsunami sources, and methods to mitigate the effects of tsunamis. The most significant, not surprisingly, are often the most devastating, such as the 2011 Tohoku, Japan earthquake and tsunami. The goal of this poster is to give a brief overview of the occurrence of tsunamis and then focus specifically on several significant tsunamis. There are various criteria to determine the most significant tsunamis: the number of deaths, amount of damage, maximum runup height, had a major impact on tsunami science or policy, etc. As a result, descriptions will include some of the most costly (2011 Tohoku, Japan), the most deadly (2004 Sumatra, 1883 Krakatau), and the highest runup ever observed (1958 Lituya Bay, Alaska). The discovery of the Cascadia subduction zone as the source of the 1700 Japanese "Orphan" tsunami and a future tsunami threat to the U.S. northwest coast, contributed to the decision to form the U.S. National Tsunami Hazard Mitigation Program. The great Lisbon earthquake of 1755 marked the beginning of the modern era of seismology. Knowledge gained from the 1964 Alaska earthquake and tsunami helped confirm the theory of plate tectonics. The 1946 Alaska, 1952 Kuril Islands, 1960 Chile, 1964 Alaska, and the 2004 Banda Aceh, tsunamis all resulted in warning centers or systems being established.The data descriptions on this poster were extracted from NOAA's National Geophysical Data Center (NGDC) global historical tsunami database. Additional information about these tsunamis, as well as water level data can be found by accessing the NGDC website www.ngdc.noaa.gov/hazard/

  3. Feeding Releases Endogenous Opioids in Humans.

    Science.gov (United States)

    Tuulari, Jetro J; Tuominen, Lauri; de Boer, Femke E; Hirvonen, Jussi; Helin, Semi; Nuutila, Pirjo; Nummenmaa, Lauri

    2017-08-23

    The endogenous opioid system supports a multitude of functions related to appetitive behavior in humans and animals, and it has been proposed to govern hedonic aspects of feeding thus contributing to the development of obesity. Here we used positron emission tomography to investigate whether feeding results in hedonia-dependent endogenous opioid release in humans. Ten healthy males were recruited for the study. They were scanned with the μ-opioid-specific ligand [ 11 C]carfentanil three times, as follows: after a palatable meal, a nonpalatable meal, and after an overnight fast. Subjective mood, satiety, and circulating hormone levels were measured. Feeding induced significant endogenous opioid release throughout the brain. This response was more pronounced following a nonpalatable meal versus a palatable meal, and independent of the subjective hedonic responses to feeding. We conclude that feeding consistently triggers cerebral opioid release even in the absence of subjective pleasure associated with feeding, suggesting that metabolic and homeostatic rather than exclusively hedonic responses play a role in the feeding-triggered cerebral opioid release. SIGNIFICANCE STATEMENT The endogenous opioid system supports both hedonic and homeostatic functions. It has been proposed that overeating and concomitant opioid release could downregulate opioid receptors and promote the development of obesity. However, it remains unresolved whether feeding leads to endogenous opioid release in humans. We used in vivo positron emission tomography to test whether feeding triggers cerebral opioid release and whether this response is associated with pleasurable sensations. We scanned volunteers using the μ-opioid receptor-specific radioligand [ 11 C]carfentanil three times, as follows: after an overnight fast, after consuming a palatable meal, and after consuming a nonpalatable meal. Feeding led to significant endogenous opioid release, and this occurred also in the absence of feeding

  4. The effects of extreme rainfall events on carbon release from Biological Soil Crusts covered soil in fixed sand dunes in the Tengger Desert, northern China

    Science.gov (United States)

    Zhao, Yang; Li, Xinrong; Pan, Yanxia; Hui, Rong

    2016-04-01

    How soil cover types and extreme rainfall event influence carbon (C) release in temperate desert ecosystems has largely been unexplored. We assessed the effects of extreme rainfall (quantity and intensity) events on the carbon release from soils covered by different types of biological soil crusts (BSCs) in fixed sand dunes in the Tengger Desert, Shapotou regionof northern China. We removed intact crusts down to 10 cm and measured them in PVC mesocosms. A Li-6400-09 Soil Chamber was used to measure the respiration rates of the BSCs immediately after the rainfall stopped, and continued until the respiration rates of the BSCs returned to the pre-rainfall basal rate. Our results showed that almost immediately after extreme rainfall events the respiration rates of algae crust and mixed crust were significantly inhibited, but moss crust was not significantly affected. The respiration rates of algae crust, mixed crust, and moss crust in extreme rainfall quantity and intensity events were, respectively, 0.12 and 0.41 μmolCO2/(m2•s), 0.10 and 0.45 μmolCO2/(m2•s), 0.83 and 1.69 μmolCO2/(m2•s). Our study indicated that moss crust in the advanced succession stage can well adapt to extreme rainfall events in the short term. Keywords: carbon release; extreme rainfall events; biological soil crust

  5. RAVEN Beta Release

    International Nuclear Information System (INIS)

    Rabiti, Cristian; Alfonsi, Andrea; Cogliati, Joshua Joseph; Mandelli, Diego; Kinoshita, Robert Arthur; Wang, Congjian; Maljovec, Daniel Patrick; Talbot, Paul William

    2016-01-01

    This documents the release of the Risk Analysis Virtual Environment (RAVEN) code. A description of the RAVEN code is provided, and discussion of the release process for the M2LW-16IN0704045 milestone. The RAVEN code is a generic software framework to perform parametric and probabilistic analysis based on the response of complex system codes. RAVEN is capable of investigating the system response as well as the input space using Monte Carlo, Grid, or Latin Hyper Cube sampling schemes, but its strength is focused toward system feature discovery, such as limit surfaces, separating regions of the input space leading to system failure, using dynamic supervised learning techniques. RAVEN has now increased in maturity enough for the Beta 1.0 release.

  6. RAVEN Beta Release

    Energy Technology Data Exchange (ETDEWEB)

    Rabiti, Cristian [Idaho National Lab. (INL), Idaho Falls, ID (United States); Alfonsi, Andrea [Idaho National Lab. (INL), Idaho Falls, ID (United States); Cogliati, Joshua Joseph [Idaho National Lab. (INL), Idaho Falls, ID (United States); Mandelli, Diego [Idaho National Lab. (INL), Idaho Falls, ID (United States); Kinoshita, Robert Arthur [Idaho National Lab. (INL), Idaho Falls, ID (United States); Wang, Congjian [Idaho National Lab. (INL), Idaho Falls, ID (United States); Maljovec, Daniel Patrick [Idaho National Lab. (INL), Idaho Falls, ID (United States); Talbot, Paul William [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2016-02-01

    This documents the release of the Risk Analysis Virtual Environment (RAVEN) code. A description of the RAVEN code is provided, and discussion of the release process for the M2LW-16IN0704045 milestone. The RAVEN code is a generic software framework to perform parametric and probabilistic analysis based on the response of complex system codes. RAVEN is capable of investigating the system response as well as the input space using Monte Carlo, Grid, or Latin Hyper Cube sampling schemes, but its strength is focused toward system feature discovery, such as limit surfaces, separating regions of the input space leading to system failure, using dynamic supervised learning techniques. RAVEN has now increased in maturity enough for the Beta 1.0 release.

  7. Quantity of Candida Colonies in Saliva: 
A Diagnostic Evaluation for Oral Candidiasis.

    Science.gov (United States)

    Zhou, Pei Ru; Hua, Hong; Liu, Xiao Song

    To investigate the relationship between the quantity of Candida colonies in saliva and oral candidiasis (OC), as well as to identify the threshold for distinguishing oral candidiasis from healthy carriage. A diagnostic test was conducted in 197 patients with different oral problems. The diagnosis of OC was established based on clinical features. Whole saliva samples from the subjects were cultured for Candida species. Receiver operating characteristic (ROC) curve analysis was used in this study. OC patients had significantly more Candida colony-forming units per millilitre saliva (795 cfu/ml) than asymptomatic carriers (40 cfu/ml; P candidiasis, the quantity of Candida colonies differed. The number of Candida colonies in pseudomembranous type was significantly higher than that in the erythematous type (P < 0.05). Candida albicans was the predominant species of Candida. The cut-off point with the best fit for OC diagnosis was calculated to be 266 cfu/ml. The sensitivity and specificity were 0.720 and 0.825, respectively. Analysis of the ROC curve indicated that Candida colonies had a high diagnostic value for OC, as demonstrated by the area under the curve (AUC = 0.873). Based on this study, the value of 270 cfu/ml was considered a threshold for distinguishing OC from carriage.

  8. Effect of vitamin E supplementation on semen quantity and quality of Local Kampong roosters

    Directory of Open Access Journals (Sweden)

    Mohamad Asrol, K

    2017-09-01

    Full Text Available This experiment was conducted to investigate the effect of increasing dietary levels of vitamin E on semen quantity and quality characteristics of local kampong roosters. Forty-five roosters were randomly distributed equally to 3 treatment groups with each group consisting of 5 replicates of 3 roosters per replicate. The 3 treatment groups were no vitamin E (T0, 200 IU vitamin E (T1 and 400 IU vitamin E (T2 supplementations. DL a-tocopherol acetate was used as the source of vitamin E. Commercial broiler feed, crushed corn and water were given ad libitum. Semen quantity and quality were evaluated at week 2, 3 and 4 after the initial vitamin E supplementation. Improvement in semen production characteristics was only noticeable after 4 wk of vitamin E supplementation. Semen characteristics (sperm gross motility score, percentage of live sperm and colour score at week 4 after supplementation were significantly higher (6.20 � 1.10, 81.68 � 5.39% and 2.80 � 0.30, respectively in T2 group (P < 0.05 compared to control group. Percentages of abnormal tail spermatozoa were significantly (P < 0.05 lower (3.84 � 2.55 T2 group compared to control group. From this study, it can be concluded that higher supplementation of dietary vitamin E is beneficial in improving the semen characteristics of local kampong chicken after 4 wk of supplementation.

  9. Process of quantity determination of uranium by chromatography in liquid zone

    International Nuclear Information System (INIS)

    Muller, J.P.; Cojean, J.; Daubizit, M.

    1993-01-01

    The invention concerns a process of quantity determination of uranium by chromatography in liquid zone, usable to determine the quantity of uranium traces. Solutions to be treated can be aqueous or organic

  10. Friendship quantity and quality as predictors of rejection sensitivity in adolescents

    Directory of Open Access Journals (Sweden)

    Gabriela Šeboková

    2014-12-01

    Full Text Available The current study examines friendship quality and quantity as unique predictors of rejection sensitivity in adolescents. The purpose of the study was to analyze whether the unique contributions of friendship quality and quantity differ in adolescent boys and girls. Rejection sensitivity is conceptualized as the disposition to anxiously expect, readily perceive and intensively react to social rejection. That is why rejection sensitivity is considered to be a cognitive-affective mechanism which leads to increase of internalizing problems in children and adolescents (loneliness, social anxiety, depression.... Friendship variables have been found to predict the level of internalizing problems in adolescents. Little to no research, however, has examined friendship quality and quantity as predictors of level of rejection sensitivity. Participants in this study were 184 students (98 girls and 86 boys, aged from 13 to 16 (M=13.83, SD=1. Adolescents completed measures assessing number of their friends, quality of best friendship (self-report questionnaire Friendship qualities scale, Bukowski, Hoza, Boivin, 1994 and rejection sensitivity (self-report questionnaire Rejection sensitivity scale, Downey, Feldman, 1996. Regression analysis indicated that friendship features (companionship, balance, help, security, closeness, friendship quantity and overall friendship quality are significant unique predictors of sensitivity rejection in adolescents with. Results suggest that adolescents with higher number of and higher quality friendships have lower concerns about the possibility and expectation of rejection, which can lead to minimizing the risk of development of internalizing problems. However, only a small proportion of variance was accounted for in rejection sensitivity by the friendship variables (small to medium effect size. This suggests that different kind of peer relationships (peer acceptance, popularity, peer victimization make unique, differential

  11. Order Quantity Distributions: Estimating an Adequate Aggregation Horizon

    Directory of Open Access Journals (Sweden)

    Eriksen Poul Svante

    2016-09-01

    Full Text Available In this paper an investigation into the demand, faced by a company in the form of customer orders, is performed both from an explorative numerical and analytical perspective. The aim of the research is to establish the behavior of customer orders in first-come-first-serve (FCFS systems and the impact of order quantity variation on the planning environment. A discussion of assumptions regarding demand from various planning and control perspectives underlines that most planning methods are based on the assumption that demand in the form of customer orders are independently identically distributed and stem from symmetrical distributions. To investigate and illustrate the need to aggregate demand to live up to these assumptions, a simple methodological framework to investigate the validity of the assumptions and for analyzing the behavior of orders is developed. The paper also presents an analytical approach to identify the aggregation horizon needed to achieve a stable demand. Furthermore, a case study application of the presented framework is presented and concluded on.

  12. Deep groundwater quantity and quality in the southwestern US

    Science.gov (United States)

    Kang, M.; Ayars, J. E.; Jackson, R. B.

    2017-12-01

    Groundwater demands are growing in many arid regions and adaptation through the use of non-traditional resources during extreme droughts is increasingly common. One such resource is deep groundwater, which we define as deeper than 300 m and up to several kilometer-depths. Although deep groundwater has been studied in the context of oil and gas, geothermal, waste disposal, and other uses, it remains poorly characterized, especially for the purposes of human consumption and irrigation uses. Therefore, we evaluate deep groundwater quantity and quality within these contexts. We compile and analyze data from water management agencies and oil and gas-based sources for the southwestern US, with a detailed look at California's Central Valley. We also use crop tolerance thresholds to evaluate deep groundwater quality for irrigation purposes. We find fresh and usable groundwater volume estimates in California's Central Valley to increase by three- and four-fold respectively when depths of up to 3 km are considered. Of the ten basins in the southwestern US with the most data, we find that the Great Basin has the greatest proportions of fresh and usable deep groundwater. Given the potentially large deep groundwater volumes, it is important to characterize the resource, guard against subsidence where extracted, and protect it for use in decades and centuries to come.

  13. Ship waste quantities prediction model for the port of Belgrade

    Directory of Open Access Journals (Sweden)

    VLADANKA PRESBURGER ULNIKOVIĆ

    2011-06-01

    Full Text Available This study focuses on the issues related to the waste management in river ports in general and especially in the port of Belgrade. Data on solid waste, waste oils, oily waters, gray water and black water have been collected for a period of five years. The methodology of data collection is presented. Trends of data were analyzed and the regression model was used to predict the waste quantities in the Belgrade port. This data could be utilized as a basis for the calculation of the equipment capacity for waste selective collection, treatment and storage. The results presented in this study establish the need for an orga¬nized management system for this type of waste which can be achieved either by constructing and providing new specialized terminal or by providing mobile floating facilities and other plants in the Port of Belgrade for these kinds of ser¬vices. In addition to the above, the legislative and organizational strategy of waste management has been explored to complete the study because the im¬pact of good waste management on environment and prevention of environ¬mental accidents would be highly beneficial. This study demonstrated that ad¬dressing these issues should be considered at international as well as national level.

  14. A pilot study to evaluate runoff quantity from green roofs.

    Science.gov (United States)

    Lee, Ju Young; Lee, Min Jung; Han, Mooyoung

    2015-04-01

    The use of green roofs is gaining increased recognition in many countries as a solution that can be used to improve environmental quality and reduce runoff quantity. To achieve these goals, pilot-scale green roof assemblies have been constructed and operated in an urban setting. From a stormwater management perspective, green roofs are 42.8-60.8% effective in reducing runoff for 200 mm soil depth and 13.8-34.4% effective in reducing runoff for 150 mm soil depth. By using Spearman rank correlation analysis, high rainfall intensity was shown to have a negative relationship with delayed occurrence time, demonstrating that the soil media in green roofs do not efficiently retain rainwater. Increasing the number of antecedent dry days can help to improve water retention capacity and delay occurrence time. From the viewpoint of runoff water quality, green roofs are regarded as the best management practice by filtration and adsorption through growth media (soil). Copyright © 2015 Elsevier Ltd. All rights reserved.

  15. Quantity and Quality of Inhaled Dose Predicts Immunopathology in Tuberculosis

    Directory of Open Access Journals (Sweden)

    Kevin Patrick Fennelly

    2015-06-01

    Full Text Available Experimental animal models of tuberculosis (TB have convincingly demonstrated that inhaled dose predicts immunopathology and survival. In contrast, the importance of inhaled dose has generally not been appreciated in TB epidemiology, clinical science, or the practice of TB control. Infectiousness of TB patients has traditionally been assessed using microscopy for acid-fast bacilli in the sputum, which should be considered only a risk factor. We have recently demonstrated that cough aerosol cultures from index cases with pulmonary TB are the best predictors of new infection among household contacts. We suggest that cough aerosols of M. tuberculosis are the best surrogates of inhaled dose, and we hypothesize that the quantity of cough aerosols is associated with TB infection versus disease. Although several factors affect the quality of infectious aerosols, we propose that the particle size distribution of cough aerosols is an important predictor of primary upper airway disease and cervical lymphadenitis and of immune responses in exposed hosts. We hypothesize that large droplet aerosols (> 5 microns containing M. tuberculosis deposit in the upper airway and can induce immune responses without establishing infection. We suggest that this may partially explain the large proportion of humans who never develop TB disease in spite of having immunological evidence of M. tuberculosis infection (e.g. positive TST or IGRA. If these hypotheses are proven true, they would alter the current paradigm of latent TB infection and reactivation, further demonstrating the need for better biomarkers or methods of assessing TB infection and the risk of developing disease.

  16. BIM IMPLEMENTATION IN A NEW ZEALAND CONSULTING QUANTITY SURVEYING PRACTICE

    Directory of Open Access Journals (Sweden)

    Curtis Harrison

    2015-07-01

    Full Text Available 5D BIM – generating cost data via the building information modelling (BIM process- has the potential to be used by quantity surveyors (QSs to streamline their workflows and increase their provision of quality service. Consultant QSs experienced in the use 5D BIM, from the New Zealand office of one large global practice, were interviewed on their perceptions of the benefits of, and barriers to, 5D BIM implementation within their firm. Findings suggest that 5D BIM has numerous benefits over traditional methods, chiefly through the increased efficiency and visualization that BIM provides, along with the rapid identification of design changes. However, realization of these perceived benefits limited to date, due to several barriers hindering 5D BIM implementation: incomplete design and insufficient model object data in the BIM model; a lack of standards to facilitate electronic measurement; legal issues, and a lack of government support. However, participants perceived that 5D BIM implementation will achieve these benefits to a far greater extent in the future. Further research is recommended to identify the BIM skills which QSs will need in the future to reach the full potential of 5D BIM

  17. Quantities of actinides in nuclear reactor fuel cycles

    International Nuclear Information System (INIS)

    Ang, K.P.

    1975-01-01

    The quantities of plutonium and other fuel actinides have been calculated for equilibrium fuel cycles for 1000 MW reactors of the following types: water reactors fueled with slightly enriched uranium, water reactors fueled with plutonium and natural uranium, fast-breeder reactors, gas-cooled reactors fueled with thorium and highly enriched uranium, and gas-cooled reactors fueled with thorium, plutonium, and recycled uranium. The radioactivity levels of plutonium, americium, and curium processed yearly in these fuel cycles are greatest for the water reactors fueled with natural uranium and recycled plutonium. The total amount of actinides processed is calculated for the predicted future growth of the United States nuclear power industry. For the same total installed nuclear power capacity, the introduction of the plutonium breeder has little effect upon the total amount of plutonium processed in this century. The estimated amount of plutonium in the low-level process wastes in the plutonium fuel cycles is comparable to the amount of plutonium in the high-level fission product wastes. The amount of plutonium processed in the nuclear fuel cycles can be considerably reduced by using gas-cooled reactors to consume plutonium produced in uranium-fueled water reactors. These, and other reactors dedicated for plutonium utilization, could be co-located with facilities for fuel reprocessing and fuel fabrication to eliminate the off-site transport of separated plutonium. (U.S.)

  18. Dynamic Coding of Signed Quantities in Cortical Feedback Circuits

    Directory of Open Access Journals (Sweden)

    Dana eBallard

    2012-08-01

    Full Text Available In the early sensory and motor areas of the cortex, individual neurons transmit information about specific sensory features via a peaked response. This concept has been crystallized as `labeled lines,' to denote that axons communicate the specific properties of their sensory or motor parent cell. Such cells also can be characterized as being polarized, that is, as representing a signed quantity that is either positive or negative. We show in a model simulation that there are two important consequences when learning receptive fields using such signed codings in circuits that subtract different inputs. The first is that, in feedback circuits using labeled lines, such arithmetic operations need to be distributed across multiple distinct pathways. The second consequence is that such pathways must be necessarily dynamic, i.e. that synapses can grow and retract when forming receptive fields. The model monitors the breaking and growing of new circuit connections when their synapses need to change polarities and predicts that the rate of such changes should be inversely correlated with the progress of receptive field formation.

  19. Sound radiation quantities arising from a resilient circular radiator.

    Science.gov (United States)

    Aarts, Ronald M; Janssen, Augustus J E M

    2009-10-01

    Power series expansions in ka are derived for the pressure at the edge of a radiator, the reaction force on the radiator, and the total radiated power arising from a harmonically excited, resilient, flat, circular radiator of radius a in an infinite baffle. The velocity profiles on the radiator are either Stenzel functions (1-(sigma/a)2)n, with sigma the radial coordinate on the radiator, or linear combinations of Zernike functions Pn(2(sigma/a)2-1), with Pn the Legendre polynomial of degree n. Both sets of functions give rise, via King's integral for the pressure, to integrals for the quantities of interest involving the product of two Bessel functions. These integrals have a power series expansion and allow an expression in terms of Bessel functions of the first kind and Struve functions. Consequently, many of the results in [M. Greenspan, J. Acoust. Soc. Am. 65, 608-621 (1979)] are generalized and treated in a unified manner. A foreseen application is for loudspeakers. The relation between the radiated power in the near-field on one hand and in the far field on the other is highlighted.

  20. Energy taxes, resource taxes and quantity rationing for climate protection

    Energy Technology Data Exchange (ETDEWEB)

    Eisenack, Klaus [Oldenburg Univ. (Germany). Dept. of Economics; Edenhofer, Ottmar; Kalkuhl, Matthias [Potsdam-Institut fuer Klimafolgenforschung e.V., Potsdam (Germany)

    2010-11-15

    Economic sectors react strategically to climate policy, aiming at a re-distribution of rents. Established analysis suggests a Pigouvian emission tax as efficient instrument, but also recommends factor input or output taxes under specific conditions. However, existing studies leave it open whether output taxes, input taxes or input rationing perform better, and at best only touch their distributional consequences. When emissions correspond to extracted ressources, it is questionable whether taxes are effective at all. We determine the effectiveness, efficiency and functional income distribution for these instruments in the energy and resource sector, based on a game theoretic growth model with explicit factor markets and policy instruments. Market equilibrium depends on a government that acts as a Stackelberg leader with a climate protection goal. We find that resource taxes and cumulative resource quantity rationing achieve this objective efficiently. Energy taxation is only second best. Mitigation generates a substantial ''climate rent'' in the resource sector that can be converted to transfer incomes by taxes. (orig.)

  1. Guidance for Evaluating the Safety of Experimental Releases of Mosquitoes, Emphasizing Mark-Release-Recapture Techniques.

    Science.gov (United States)

    Benedict, Mark Q; Charlwood, J Derek; Harrington, Laura C; Lounibos, L Philip; Reisen, William K; Tabachnick, Walter J

    2018-01-01

    Experimental releases of mosquitoes are performed to understand characteristics of populations related to the biology, ability to transmit pathogens, and ultimately their control. In this article, we discuss considerations related to the safety of experimental releases of living mosquitoes, applying principles of good practice in vector biology that protect human health and comfort. We describe specific factors of experimental releases of mosquitoes that we believe are critical to inform institutional biosafety committees and similar review boards to which proposals to conduct mosquito release experiments have been submitted. In this study, "experimental releases" means those that do not significantly increase vector capacity or nuisance biting relative to the unperturbed natural baseline. This document specifically does not address releases of mosquitoes for ongoing control programs or trials of new control methods for which broader assessments of risk are required. It also does not address releases of transgenic or exotic (non-native) mosquito species, both of which require particular regulatory approval. Experimental releases may include females and males and evaluation must consider their effects based on the number released, their genotype and phenotype, the environment into which they are released, and postrelease collection activities. We consider whether increases of disease transmission and nuisance biting might result from proposed experimental releases against the backdrop of natural population size variation. We recommend that experimental releases be conducted in a manner that can be reasonably argued to have insignificant negative effects. Reviewers of proposals for experimental releases should expect applicants to provide such an argument based on evidence from similar studies and their planned activities. This document provides guidance for creating and evaluating such proposals.

  2. Cytotoxic effects of glass ionomer cements on human dental pulp stem cells correlate with fluoride release.

    Science.gov (United States)

    Kanjevac, Tatjana; Milovanovic, Marija; Volarevic, Vladislav; Lukic, Miodrag L; Arsenijevic, Nebojsa; Markovic, Dejan; Zdravkovic, Nebojsa; Tesic, Zivoslav; Lukic, Aleksandra

    2012-01-01

    Glass ionomer cements (GICs) are commonly used as restorative materials. Responses to GICs differ among cell types and it is therefore of importance to thoroughly investigate the influence of these restorative materials on pulp stem cells that are potential source for dental tissue regeneration. Eight biomaterials were tested: Fuji I, Fuji II, Fuji VIII, Fuji IX, Fuji Plus, Fuji Triage, Vitrebond and Composit. We compared their cytotoxic activity on human dental pulp stem cells (DPSC) and correlated this activity with the content of Fluoride, Aluminium and Strontium ions in their eluates. Elution samples of biomaterials were prepared in sterile tissue culture medium and the medium was tested for toxicity by an assay of cell survival/proliferation (MTT test) and apoptosis (Annexin V FITC Detection Kit). Concentrations of Fluoride, Aluminium and Strontium ions were tested by appropriate methods in the same eluates. Cell survival ranged between 79.62% (Fuji Triage) to 1.5% (Fuji Plus) and most dead DPSCs were in the stage of late apoptosis. Fluoride release correlated with cytotoxicity of GICs, while Aluminium and Strontium ions, present in significant amount in eluates of tested GICs did not. Fuji Plus, Vitrebond and Fuji VIII, which released fluoride in higher quantities than other GICs, were highly toxic to human DPSCs. Opposite, low levels of released fluoride correlated to low cytotoxic effect of Composit, Fuji I and Fuji Triage.

  3. A 'Puff' dispersion model for routine and accidental releases

    International Nuclear Information System (INIS)

    Grsic, Z.; Rajkovic, B.; Milutinovic, P.

    1999-01-01

    A Puff dispersion model for accidental or routine releases is presented. This model was used as a constitutive part of an automatic meteorological station.All measured quantities are continuously displayed on PC monitor in a digital and graphical form, they are averaging every 10 minutes and sending to the civil information center of Belgrade. In the paper simulation of a pollutant plume dispersion from The oil refinery 'Pancevo', on April 18 th 1999 is presented. (author)

  4. Symbolic Estrangement: Evidence against a Strong Association between Numerical Symbols and the Quantities They Represent

    Science.gov (United States)

    Lyons, Ian M.; Ansari, Daniel; Beilock, Sian L.

    2012-01-01

    Are numerals estranged from a sense of the actual quantities they represent? We demonstrate that, irrespective of numerical size or distance, direct comparison of the relative quantities represented by symbolic and nonsymbolic formats leads to performance markedly worse than when comparing 2 nonsymbolic quantities (Experiment 1). Experiment 2…

  5. 48 CFR 245.7309-8 - Variations in quantity or weight.

    Science.gov (United States)

    2010-10-01

    ... Inventory 245.7309-8 Variations in quantity or weight. When property is sold on a “unit price” basis, the Contractor reserves the right to vary by up to 15 percent the quantity or weight listed in the Invitation and... price shall be adjusted in accordance with the unit price and on the basis of the quantity or weight...

  6. 40 CFR 273.8 - Applicability-household and conditionally exempt small quantity generator waste.

    Science.gov (United States)

    2010-07-01

    ... conditionally exempt small quantity generator waste. 273.8 Section 273.8 Protection of Environment ENVIRONMENTAL....8 Applicability—household and conditionally exempt small quantity generator waste. (a) Persons... universal wastes defined at § 273.9; and/or (2) Conditionally exempt small quantity generator wastes that...

  7. SOL-Gel microspheres and nanospheres for controlled release applications

    International Nuclear Information System (INIS)

    Barbe, C.; Beyer, R.; Kong, L.; Blackford, M.; Trautman, R.; Bartlett, J.

    2002-01-01

    one hour. The particles thus produced were washed with cyclohexane and carefully dried. Release Kinetics. The release of the encapsulated species from the particles was monitored by placing a fixed quantity of the sample in water or physiological saline, and monitoring the concentration of the released species using UV/Vis spectroscopy. The fraction released was normalised to the total mass initially encapsulated. The influence of the emulsion chemistry on the size of the microspheres obtained at pH 2 is illustrated in Figure 1 for microspheres containing encapsulated Orange II Using essentially identical sol-gel chemistries, particles with dimensions ranging from 50 nm to 50 μm can be readily obtained. The size of the particles is controlled by the size of the emulsion droplets, which act as micro-reactors for the sol-gel reactions. In turn, the size of the droplets is determined predominantly by the hydrophile/lipophile balance of the surfactant/ solvent couple and by processing parameters such as the water to surfactant ratio and the concentration of surfactant. The effect of sol-gel processing parameters on the morphology and associated release kinetics is illustrated in Figure 2. Although both samples have essentially identical particle sizes (not shown), their morphologies are significantly different. Processing under acidic conditions leads to the formation of nanosized linear silicate 'building block' which are woven tightly together in the final gel matrix, to produce a microporous material (pore diameters 2 nm). The different morphologies are clearly reflected in the release rate of the encapsulated species from the respective matrices; rapid release kinetics are evident for the mesoporous material (high pH), while significantly slower release rates are obtained for the microporous material (low pH). A combined sol-gel/emulsion processing method has been developed to produce inorganic matrices with tailored nanostructures containing encapsulated organic and

  8. Testing Significance Testing

    Directory of Open Access Journals (Sweden)

    Joachim I. Krueger

    2018-04-01

    Full Text Available The practice of Significance Testing (ST remains widespread in psychological science despite continual criticism of its flaws and abuses. Using simulation experiments, we address four concerns about ST and for two of these we compare ST’s performance with prominent alternatives. We find the following: First, the 'p' values delivered by ST predict the posterior probability of the tested hypothesis well under many research conditions. Second, low 'p' values support inductive inferences because they are most likely to occur when the tested hypothesis is false. Third, 'p' values track likelihood ratios without raising the uncertainties of relative inference. Fourth, 'p' values predict the replicability of research findings better than confidence intervals do. Given these results, we conclude that 'p' values may be used judiciously as a heuristic tool for inductive inference. Yet, 'p' values cannot bear the full burden of inference. We encourage researchers to be flexible in their selection and use of statistical methods.

  9. Safety significance evaluation system

    International Nuclear Information System (INIS)

    Lew, B.S.; Yee, D.; Brewer, W.K.; Quattro, P.J.; Kirby, K.D.

    1991-01-01

    This paper reports that the Pacific Gas and Electric Company (PG and E), in cooperation with ABZ, Incorporated and Science Applications International Corporation (SAIC), investigated the use of artificial intelligence-based programming techniques to assist utility personnel in regulatory compliance problems. The result of this investigation is that artificial intelligence-based programming techniques can successfully be applied to this problem. To demonstrate this, a general methodology was developed and several prototype systems based on this methodology were developed. The prototypes address U.S. Nuclear Regulatory Commission (NRC) event reportability requirements, technical specification compliance based on plant equipment status, and quality assurance assistance. This collection of prototype modules is named the safety significance evaluation system

  10. Predicting significant torso trauma.

    Science.gov (United States)

    Nirula, Ram; Talmor, Daniel; Brasel, Karen

    2005-07-01

    Identification of motor vehicle crash (MVC) characteristics associated with thoracoabdominal injury would advance the development of automatic crash notification systems (ACNS) by improving triage and response times. Our objective was to determine the relationships between MVC characteristics and thoracoabdominal trauma to develop a torso injury probability model. Drivers involved in crashes from 1993 to 2001 within the National Automotive Sampling System were reviewed. Relationships between torso injury and MVC characteristics were assessed using multivariate logistic regression. Receiver operating characteristic curves were used to compare the model to current ACNS models. There were a total of 56,466 drivers. Age, ejection, braking, avoidance, velocity, restraints, passenger-side impact, rollover, and vehicle weight and type were associated with injury (p < 0.05). The area under the receiver operating characteristic curve (83.9) was significantly greater than current ACNS models. We have developed a thoracoabdominal injury probability model that may improve patient triage when used with ACNS.

  11. Gas revenue increasingly significant

    International Nuclear Information System (INIS)

    Megill, R.E.

    1991-01-01

    This paper briefly describes the wellhead prices of natural gas compared to crude oil over the past 70 years. Although natural gas prices have never reached price parity with crude oil, the relative value of a gas BTU has been increasing. It is one of the reasons that the total amount of money coming from natural gas wells is becoming more significant. From 1920 to 1955 the revenue at the wellhead for natural gas was only about 10% of the money received by producers. Most of the money needed for exploration, development, and production came from crude oil. At present, however, over 40% of the money from the upstream portion of the petroleum industry is from natural gas. As a result, in a few short years natural gas may become 50% of the money revenues generated from wellhead production facilities

  12. Characterisation, quantity and sorptive properties of microplastics extracted from cosmetics.

    Science.gov (United States)

    Napper, Imogen E; Bakir, Adil; Rowland, Steven J; Thompson, Richard C

    2015-10-15

    Cosmetic products, such as facial scrubs, have been identified as potentially important primary sources of microplastics to the marine environment. This study characterises, quantifies and then investigates the sorptive properties of plastic microbeads that are used as exfoliants in cosmetics. Polyethylene microbeads were extracted from several products, and shown to have a wide size range (mean diameters between 164 and 327 μm). We estimated that between 4594 and 94,500 microbeads could be released in a single use. To examine the potential for microbeads to accumulate and transport chemicals they were exposed to a binary mixture of (3)H-phenanthrene and (14)C-DDT in seawater. The potential for transport of sorbed chemicals by microbeads was broadly similar to that of polythene (PE) particles used in previous sorption studies. In conclusion, cosmetic exfoliants are a potentially important, yet preventable source of microplastic contamination in the marine environment. Copyright © 2015 Elsevier Ltd. All rights reserved.

  13. Influence of diet quantity on learning and memory ability and immunological function in mice

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    evaluate learning ability and the memory ability was retested at 24 hours later.Times of autonomic activity within 5 minutes were used to evaluate ability of autonomic activity.In addition,blood was collected from eyeball to measure plasma immune globulin and complement by using immunoturbidimetry.MAIN OUTCOME MEASURES:① Effect of different diet quantity on learning and memory ability;②effect of different diet quantity on times of autonomic activity and survival time under hypoxia and normal pressure;③ effect of different diet quantity on content of immune globulin and complement.RESULTS:All 80 mice were involved in the final analysis.① Effect of different diet quantity on learning and memory ability:There was no significant difference in learning ability during step down test (P>0.05).While,memory ability in the over-diet group and the quantitative-diet group was better than that in the over-limit diet group (t=2.235 - 2.423,P<0.05).During shuttle box test,learning and memory ability in the over-diet group was superior to that in the over-limit diet group (t =2.237 - 2.431,P<0.05).While,memory ability in the quantitative-diet group and quantitative-limit diet group was superior to that in the over-limit group (t =2.704 - 2.813,P<0.05).② Effect of different diet quantity on times of autonomic activity and survival time under hypoxia and normal pressure:There were significant differences in the times of autonomic activity among quantitative-diet group,quantitative-limit diet group and over-limit diet group (t=2.725 - 2.98,P<0.05).Survival time in the quantitative-diet group and the quantitative-limit diet group was longer than that in the over-diet group (7=2.365,2.719,P<0.05),but shorter than that in the over-limit diet group (t =2.427,2.538,P<0.05).While,survival time in the over-limit diet group was longer than that in the over-diet group (t =2.765,P<0.01).③Effect of different diet quantity on content of immune globulin and complement

  14. Hydraulic release oil tool

    International Nuclear Information System (INIS)

    Mims, M.G.; Mueller, M.D.; Ehlinger, J.C.

    1992-01-01

    This patent describes a hydraulic release tool. It comprises a setting assembly; a coupling member for coupling to drill string or petroleum production components, the coupling member being a plurality of sockets for receiving the dogs in the extended position and attaching the coupling member the setting assembly; whereby the setting assembly couples to the coupling member by engagement of the dogs in the sockets of releases from and disengages the coupling member in movement of the piston from its setting to its reposition in response to a pressure in the body in exceeding the predetermined pressure; and a relief port from outside the body into its bore and means to prevent communication between the relief port and the bore of the body axially of the piston when the piston is in the setting position and to establish such communication upon movement of the piston from the setting position to the release position and reduce the pressure in the body bore axially of the piston, whereby the reduction of the pressure signals that the tool has released the coupling member

  15. APASS Data Release 10

    Science.gov (United States)

    Henden, Arne A.; Levine, Stephen; Terrell, Dirk; Welch, Douglas L.; Munari, Ulisse; Kloppenborg, Brian K.

    2018-06-01

    The AAVSO Photometric All-Sky Survey (APASS) has been underway since 2010. This survey covers the entire sky from 7.5 knowledge of the optical train distortions. With these changes, DR10 includes many more stars than prior releases. We describe the survey, its remaining limitations, and prospects for the future, including a very-bright-star extension.

  16. Release the Prisoners Game

    Science.gov (United States)

    Van Hecke, Tanja

    2011-01-01

    This article presents the mathematical approach of the optimal strategy to win the "Release the prisoners" game and the integration of this analysis in a math class. Outline lesson plans at three different levels are given, where simulations are suggested as well as theoretical findings about the probability distribution function and its mean…

  17. Tumor significant dose

    International Nuclear Information System (INIS)

    Supe, S.J.; Nagalaxmi, K.V.; Meenakshi, L.

    1983-01-01

    In the practice of radiotherapy, various concepts like NSD, CRE, TDF, and BIR are being used to evaluate the biological effectiveness of the treatment schedules on the normal tissues. This has been accepted as the tolerance of the normal tissue is the limiting factor in the treatment of cancers. At present when various schedules are tried, attention is therefore paid to the biological damage of the normal tissues only and it is expected that the damage to the cancerous tissues would be extensive enough to control the cancer. Attempt is made in the present work to evaluate the concent of tumor significant dose (TSD) which will represent the damage to the cancerous tissue. Strandquist in the analysis of a large number of cases of squamous cell carcinoma found that for the 5 fraction/week treatment, the total dose required to bring about the same damage for the cancerous tissue is proportional to T/sup -0.22/, where T is the overall time over which the dose is delivered. Using this finding the TSD was defined as DxN/sup -p/xT/sup -q/, where D is the total dose, N the number of fractions, T the overall time p and q are the exponents to be suitably chosen. The values of p and q are adjusted such that p+q< or =0.24, and p varies from 0.0 to 0.24 and q varies from 0.0 to 0.22. Cases of cancer of cervix uteri treated between 1978 and 1980 in the V. N. Cancer Centre, Kuppuswamy Naidu Memorial Hospital, Coimbatore, India were analyzed on the basis of these formulations. These data, coupled with the clinical experience, were used for choice of a formula for the TSD. Further, the dose schedules used in the British Institute of Radiology fraction- ation studies were also used to propose that the tumor significant dose is represented by DxN/sup -0.18/xT/sup -0.06/

  18. Angiogenesis in calcium phosphate scaffolds by inorganic copper ion release.

    Science.gov (United States)

    Barralet, Jake; Gbureck, Uwe; Habibovic, Pamela; Vorndran, Elke; Gerard, Catherine; Doillon, Charles J

    2009-07-01

    Angiogenesis in a tissue-engineered device may be induced by incorporating growth factors (e.g., vascular endothelial growth factor [VEGF]), genetically modified cells, and=or vascular cells. It represents an important process during the formation and repair of tissue and is essential for nourishment and supply of reparative and immunological cells. Inorganic angiogenic factors, such as copper ions, are therefore of interest in the fields of regenerative medicine and tissue engineering due to their low cost, higher stability, and potentially greater safety compared with recombinant proteins or genetic engineering approaches. The purpose of this study was to compare tissue responses to 3D printed macroporous bioceramic scaffolds implanted in mice that had been loaded with either VEGF or copper sulfate. These factors were spatially localized at the end of a single macropore some 7 mm from the surface of the scaffold. Controls without angiogenic factors exhibited only poor tissue growth within the blocks; in contrast, low doses of copper sulfate led to the formation of microvessels oriented along the macropore axis. Further, wound tissue ingrowth was particularly sensitive to the quantity of copper sulfate and was enhanced at specific concentrations or in combination with VEGF. The potential to accelerate and guide angiogenesis and wound healing by copper ion release without the expense of inductive protein(s) is highly attractive in the area of tissue-engineered bone and offers significant future potential in the field of regenerative biomaterials.

  19. Diffusion rates for elevated releases

    International Nuclear Information System (INIS)

    Ramsdell, J.V.

    1983-11-01

    A search of the literature related to diffusion from elevated sources has determined that an adequate data base exists for use in developing parameterizations for estimating diffusion rates for material released from free standing stacks at nuclear power plants. A review of published data analyses indicates that a new parameterization of horizontal diffusion rates specifically for elevated releases is not likely to significantly change the magnitudes of horizontal diffusion coefficients on the average. However, the uncertainties associated with horizontal diffusion coefficient estimates under any given set of atmospheric conditions could be reduced by a new parameterization. Similarly, a new parameterization of vertical diffusion rates would be unlikely to significantly alter the magnitudes of diffusion coefficients for unstable atmospheric conditons. However, for neutral and stable atmospheric conditions, a new parameterization of vertical diffusion rates might increase vertical diffusion coefficients significantly. The increase would move ground-level time-integrated concentration maxima closer to the plant and would increase the maxima. 55 references, 2 figures, 4 tables

  20. Forest Biomass Energy Resources in China: Quantity and Distribution

    Directory of Open Access Journals (Sweden)

    Caixia Zhang

    2015-11-01

    Full Text Available As one of the most important renewable and sustainable energy sources, the forest biomass energy resource has always been the focus of attention of scholars and policy makers. However, its potential is still uncertain in China, especially with respect to its spatial distribution. In this paper, the quantity and distribution of Chinese forest biomass energy resources are explored based mainly on forestry statistics data rather than forest resource inventory data used by most previous studies. The results show that the forest biomass energy resource in China was 169 million tons in 2010, of which wood felling and bucking residue (WFBR,wood processing residue (WPR, bamboo processing residue, fuel wood and firewood used by farmers accounted for 38%, 37%, 6%, 4% and 15%, respectively. The highest resource was located in East China, accounting for nearly 39.0% of the national amount, followed by the Southwest and South China regions, which accounted for 17.4% and 16.3%, respectively. At the provincial scale, Shandong has the highest distribution, accounting for 11.9% of total resources, followed by Guangxi and Fujian accounting for 10.3% and 10.2%, respectively. The actual wood-processing residue (AWPR estimated from the actual production of different wood products (considering the wood transferred between regions showed apparent differences from the local wood processing residue (LWPR, which assumes that no wood has been transferredbetween regions. Due to the large contribution of WPR to total forestry bioenergy resources, the estimation of AWPR will provide a more accurate evaluation of the total amount and the spatial distribution of forest biomass energy resources in China.

  1. On Complex Networks Representation and Computation of Hydrologycal Quantities

    Science.gov (United States)

    Serafin, F.; Bancheri, M.; David, O.; Rigon, R.

    2017-12-01

    Water is our blue gold. Despite results of discovery-based science keep warning public opinion about the looming worldwide water crisis, water is still treated as a not worth taking resource. Could a different multi-scale perspective affect environmental decision-making more deeply? Can also a further pairing to a new graphical representation of processes interaction sway decision-making more effectively and public opinion consequently?This abstract introduces a complex networks driven way to represent catchments eco-hydrology and related flexible informatics to manage it. The representation is built upon mathematical category. A category is an algebraic structure that comprises "objects" linked by "arrows". It is an evolution of Petri Nets said Time Continuous Petri Nets (TCPN). It aims to display (water) budgets processes and catchment interactions using explicative and self-contained symbolism. The result improves readability of physical processes compared to current descriptions. The IT perspective hinges on the Object Modeling System (OMS) v3. The latter is a non-invasive flexible environmental modeling framework designed to support component-based model development. The implementation of a Directed Acyclic Graph (DAG) data structure, named Net3, has recently enhanced its flexibility. Net3 represents interacting systems as complex networks: vertices match up with any sort of time evolving quantity; edges correspond to their data (fluxes) interchange. It currently hosts JGrass-NewAge components, and those implementing travel time analysis of fluxes. Further bio-physical or management oriented components can be easily added.This talk introduces both graphical representation and related informatics exercising actual applications and examples.

  2. Technology development for evaluation of operational quantities in radiation protection

    International Nuclear Information System (INIS)

    Jang, Si Young; Lee, T. Y.; Kim, B. H.

    2003-03-01

    Korean government recently published a national regulation on the internal exposure monitoring and dose evaluation (internal dosimetry) based on the most recent ICRP recommendation 60 and subsequent publications, which supercede the former ICRP recommendation 26 and publication 30, on which the internal dosimetry practice in Korea had been based so far. Consequently, this project, according to the demand from both government and nuclear industry, had been launched to develop a user-friendly computer code on internal dosimetry adopting the most up to date ICRP biokinetic and dosimetric model to resolve the difficulties and problems faced to nuclear industry and to develop related technology. The reliability of this code, named as BiDAS, as a result of several benchmark calculations for self assurance appeared to be excellent comparing with the foreign computer code. This computer code is expected to be successfully utilized in nuclear industry and related fields in complying with the national regulation on internal dosimetry program started from late 2003. Reference low level gamma(γ) radiation field for calibration of environmental radiation(γ) monitor and reference neutron field for calibration of n monitoring equipment have been established and characterized. International cross comparison of these reference radiation fields have been performed and radiation response of various radiation monitoring instrument has been tested by using these reference radiation fields. A technology which can directly measure the radiation quality factor and tissue absorbed dose has been established to evaluate the neutron dose in terms of operational quantity in the unknown mixed n-γ radiation field. Spherical and cylindrical TEPC systems have been designed and manufactured and a portable TEPC system to measure the neutron quality and dose in the real work field has been developed and tested in accelerator laboratory

  3. Influence of adhesive bonding on quantity of emissions VOCs

    Directory of Open Access Journals (Sweden)

    Petr Čech

    2008-01-01

    Full Text Available The study deals with the influence of urea-formaldehyde glue and veneered bolstering on technological operation veneering on quantity of emission VOCs (volatile organic compounds.The so-called Volatile Organic Compounds (VOC are among the largest pollution sources of both the internal and external environments.VOC is defined as emission of any organic compound or a mixture thereof, with the exception of methane, whereby the compound exerts the pressure of 0.01 kPa or more at the temperature of 20 °C (293.15 K and reaches the corresponding volatility under the specific conditions of its use and can undergo photochemical reactions with nitrogen oxides when exposed to solar radiation.The effects of VOC upon environment can be described by equation:VOC + NOx + UV radiation + heat = tropospheric ozone (O3.In this work there were tested background working environment in various parts of multi-storeyed press, next was judged emissive charge of veneered device and used glue. We used surface material such as chipboard. We used urea-formaldehyde glue KRONOCOL U300 on technological operation veneering.The VOC emissions from the wooden surfaces with or without finishing were tested in the Equipment for VOC Measuring with a small-space chamber. This equipment was installed in and made available by the Institute of Furniture, Design and Habitation. The small-space chamber is suitable for testing small parts of wood products. The device equipped with small-chamber satisfies all conditions mandated in the standard ENV 13 419 DIN -V-ENV 13 419 ”Determination of the emissions of Volatile organic compounds”.The VOC emissions were collected in columns with sorbent Tenax TA. We analyzed the columns with the VOC emissions by: the gas chromatography in conjunction with mass spectrometer and Direct Thermal Desorption.

  4. Calculation of uncertainties in influence quantities in biological essays

    Directory of Open Access Journals (Sweden)

    Pierre Morel

    2006-01-01

    Full Text Available Due to the need of showing the reliability of results from biological essays, such as in health and environmental areas, laboratories have been implementing quality systems, particularly ABNT NBR ISO/IEC 17025 (ABNT, 2001, which include as one of the requirements, the calculation of uncertainty in essays results. It is of common knowledge that estimating uncertainty in essays using organisms, such as animal and vegetal species, is difficult, preventing from meeting that requirement in the standard. The paper shows the calculation of uncertainties in influences quantities in these essays as a tool to allow validating the measuring process, by using the essays performed by Rhodia Environmental Impact Analysis Laboratory and IPEN Ecotoxicology Laboratory as examples.Devido à necessidade de demonstrar a confiabilidade dos resultados de ensaios biológicos como, por exemplo, nas áreas de saúde e ambiental, laboratórios vêm implementando sistemas da qualidade, em especial a ABNT NBR ISO/IEC 17025 (ABNT, 2001 que inclui como um dos requisitos o cálculo da incerteza dos resultados dos ensaios. É reconhecidamente difícil de estimar a incerteza de ensaios que utilizam organismos, como com espécies animais e vegetais o que impede, consequentemente, o atendimento deste requisito da norma. O trabalho apresenta o cálculo de incerteza das grandezas de influências nestes ensaios como uma ferramenta que permite validar o processo de medição, utilizando como exemplos aqueles realizados pelos Laboratórios de Análise de Impacto Ambiental da Rhodia e de Ecologia e Ecotoxicologia do IPEN.

  5. Meaning and significance of

    Directory of Open Access Journals (Sweden)

    Ph D Student Roman Mihaela

    2011-05-01

    Full Text Available The concept of "public accountability" is a challenge for political science as a new concept in this area in full debate and developement ,both in theory and practice. This paper is a theoretical approach of displaying some definitions, relevant meanings and significance odf the concept in political science. The importance of this concept is that although originally it was used as a tool to improve effectiveness and eficiency of public governance, it has gradually become a purpose it itself. "Accountability" has become an image of good governance first in the United States of America then in the European Union.Nevertheless,the concept is vaguely defined and provides ambiguous images of good governance.This paper begins with the presentation of some general meanings of the concept as they emerge from specialized dictionaries and ancyclopaedies and continues with the meanings developed in political science. The concept of "public accontability" is rooted in economics and management literature,becoming increasingly relevant in today's political science both in theory and discourse as well as in practice in formulating and evaluating public policies. A first conclusin that emerges from, the analysis of the evolution of this term is that it requires a conceptual clarification in political science. A clear definition will then enable an appropriate model of proving the system of public accountability in formulating and assessing public policies, in order to implement a system of assessment and monitoring thereof.

  6. Large methane releases lead to strong aerosol forcing and reduced cloudiness

    DEFF Research Database (Denmark)

    Kurten, T.; Zhou, L.; Makkonen, R.

    2011-01-01

    The release of vast quantities of methane into the atmosphere as a result of clathrate destabilization is a potential mechanism for rapid amplification of global warming. Previous studies have calculated the enhanced warming based mainly on the radiative effect of the methane itself, with smaller...... is predicted to significantly decrease hydroxyl radical (OH) concentrations, while moderately increasing ozone (O-3). These changes lead to a 70% increase in the atmospheric lifetime of methane, and an 18% decrease in global mean cloud droplet number concentrations (CDNC). The CDNC change causes a radiative...... forcing that is comparable in magnitude to the long-wave radiative forcing ("enhanced greenhouse effect") of the added methane. Together, the indirect CH4-O-3 and CH4-OHaerosol forcings could more than double the warming effect of large methane increases. Our findings may help explain the anomalously...

  7. Assessment of potential climate change impacts on peatland dissolved organic carbon release and drinking water treatment from laboratory experiments

    International Nuclear Information System (INIS)

    Tang, R.; Clark, J.M.; Bond, T.; Graham, N.; Hughes, D.; Freeman, C.

    2013-01-01

    Catchments draining peat soils provide the majority of drinking water in the UK. Over the past decades, concentrations of dissolved organic carbon (DOC) have increased in surface waters. Residual DOC can cause harmful carcinogenic disinfection by-products to form during water treatment processes. Increased frequency and severity of droughts combined with and increased temperatures expected as the climate changes, have potentials to change water quality. We used a novel approach to investigate links between climate change, DOC release and subsequent effects on drinking water treatment. We designed a climate manipulation experiment to simulate projected climate changes and monitored releases from peat soil and litter, then simulated coagulation used in water treatment. We showed that the ‘drought’ simulation was the dominant factor altering DOC release and affected the ability to remove DOC. Our results imply that future short-term drought events could have a greater impact than increased temperature on DOC treatability. - Highlights: ► We model realistic temperature and moisture changes on peat and surface vegetation. ► Quantity, quality and treatability changes of dissolved organic carbon were examined. ► Moisture has significantly greater influence than temperature on DOC production. ► Dry conditions alter treatability of DOC released from surface litter. ► Droughts have greater impact on water treatment than short-term heat waves alone. - Future drought events are likely to alter soil moisture, which predominately controls production of peat-derived dissolved organic carbon and subsequently drinking water quality.

  8. Canadian pollutant releases and transfers : NPRI data 1998

    International Nuclear Information System (INIS)

    2001-03-01

    A large, two-sided fold-out poster showing pollution hotspots throughout Canada, has been released by the Canadian Institute for Environmental Law and Policy (CIELAP). The poster is based on the maps and tables of the National Pollutant Release Inventory (NPRI) 1998. It presents the top on-site releases and off-site transfers of pollutants by facilities across Canada, and provides a summary of releases, transfers and recycling of pollutants by province. The map depicts the facilities with the five largest quantities of individual pollutants released to each medium, i. e. water, air, land, underground. The crude oil and gas, other utilities, primary metal, paper and chemical industrial sectors are responsible for the largest on-site releases, while the business services, fabricated metal. primary metal and chemical industrial sectors account for the largest off-site transfers. Twenty-five of the 176 substances whose releases and transfers are reported under the NPRI are classified as 'toxic' or 'carcinogenic'. tabs., maps

  9. Significant incidents in nuclear fuel cycle facilities

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    In contrast to nuclear power plants, events in nuclear fuel cycle facilities are not well documented. The INES database covers all the nuclear fuel cycle facilities; however, it was developed in the early 1990s and does not contain information on events prior to that. The purpose of the present report is to collect significant events and analyze them in order to give a safety related overview of nuclear fuel cycle facilities. Significant incidents were selected using the following criteria: release of radioactive material or exposure to radiation; degradation of items important to safety; and deficiencies in design, quality assurance, etc. which include criticality incidents, fire, explosion, radioactive release and contamination. This report includes an explanation, where possible, of root causes, lessons learned and action taken. 4 refs, 4 tabs.

  10. Significant incidents in nuclear fuel cycle facilities

    International Nuclear Information System (INIS)

    1996-03-01

    In contrast to nuclear power plants, events in nuclear fuel cycle facilities are not well documented. The INES database covers all the nuclear fuel cycle facilities; however, it was developed in the early 1990s and does not contain information on events prior to that. The purpose of the present report is to collect significant events and analyze them in order to give a safety related overview of nuclear fuel cycle facilities. Significant incidents were selected using the following criteria: release of radioactive material or exposure to radiation; degradation of items important to safety; and deficiencies in design, quality assurance, etc. which include criticality incidents, fire, explosion, radioactive release and contamination. This report includes an explanation, where possible, of root causes, lessons learned and action taken. 4 refs, 4 tabs

  11. The Effect of Units Lost Due to Deterioration in Fuzzy Economic Order Quantity (FEOQ Model

    Directory of Open Access Journals (Sweden)

    M. Pattnaik

    2013-07-01

    Full Text Available For several decades, the Economic Order Quantity (EOQ model and its variations have received much attention from researchers. Recently, there has been an investigation into an EOQ model incorporating effect of units lost due to deterioration in infinite planning horizon with crisp decision environment. Accounting for holding and ordering cost, as has traditionally been the case of modeling inventory systems in fuzzy environment are investigated which are not precisely known and defined on a bounded interval of real numbers. The question is how reliable are the EOQ models when items stocked deteriorate one time. This paper introduces Fuzzy Economic Order Quantity (FEOQ model in which it assumes that units lost due to deterioration is included in the objective function to properly model the problem in finite planning horizon. The numerical analysis shows that an appropriate fuzzy policy can benefit the retailer and that is significant, especially for deteriorating items is shown to be superior to that of crisp decision making. A computational algorithm using LINGO 13.0 and MATLAB (R2009a software are developed to find the optimal solution. Sensitivity analysis of the optimal solution is also studied and managerial insights are drawn which shows the influence of key model parameters.

  12. Parents face quantity-quality trade-offs between reproduction and investment in offspring in Iceland.

    Science.gov (United States)

    Lynch, Robert Francis

    2016-05-01

    How to optimally allocate time, energy and investment in an effort to maximize one's reproductive success is a fundamental problem faced by all organisms. This effort is complicated when the production of each additional offspring dilutes the total resources available for parental investment. Although a quantity-quality trade-off between producing and investing in offspring has long been assumed in evolutionary biology, testing it directly in humans is difficult, partly owing to the long generation time of our species. Using data from an Icelandic genealogy (Íslendingabók) over two centuries, I address this issue and analyse the quantity-quality trade-off in humans. I demonstrate that the primary impact of parents on the fitness of their children is the result of resources and or investment, but not genes. This effect changes significantly across time, in response to environmental conditions. Overall, increasing reproduction has negative fitness consequences on offspring, such that each additional sibling reduces an individual's average lifespan and lifetime reproductive success. This analysis provides insights into the evolutionary conflict between producing and investing in children while also shedding light on some of the causes of the demographic transition.

  13. Effect of the selected seismic energy dissipation capacity on the materials quantity for reinforced concrete walls

    Directory of Open Access Journals (Sweden)

    José Miguel Benjumea Royero

    2017-02-01

    Full Text Available Context: Regarding their design of reinforced concrete structural walls, the Colombian seismic design building code allows the engineer to select one of the three seismic energy dissipation capacity (ordinary, moderate, and special depending on the seismic hazard of the site. Despite this, it is a common practice to choose the minor requirement for the site because it is thought that selecting a higher requirement will lead to larger structural materials amounts and, therefore, cost increments.  Method: In this work, an analytical study was performed in order to determine the effect of the selected energy dissipation capacity on the quantity of materials and ductility displacement capacity of R/C walls. The study was done for a region with low seismic hazard, mainly because this permitted to explore and compare the use of the three seismic energy dissipations capacities. The effect of different parameters such as the wall total height and thickness, the tributary loaded area, and the minimum volumetric steel ratio were studied. Results: The total amount of steel required for the walls with moderate and special energy dissipation capacity corresponds, on average, to 77% and 89%, respectively, of the quantity required for walls with minimum capacity. Conclusions: it is possible to achieve reductions in the total steel required weight when adopting either moderated or special seismic energy dissipation instead of the minimum capacity.  Additionally, a significant increment in the seismic ductility displacements capacity of the wall was obtained.

  14. Effect of interfacial composition and crumbliness on aroma release in soy protein/sugar beet pectin mixed emulsion gels.

    Science.gov (United States)

    Hou, Jun-Jie; Guo, Jian; Wang, Jin-Mei; Yang, Xiao-Quan

    2016-10-01

    In this study, soy protein isolate/sugar beet pectin (SPI/SBP) emulsion gels were prepared through an enzymatic gelation process. The effects of emulsifier (SBP, SPI or SPI/SBP complex) and emulsification process on the microstructure, texture, breakdown properties and aroma release behavior of resulting emulsion gels were investigated. Oil emulsification by SBP/SPI complex resulted in a higher amount of emulsifier absorbing on the oil-water interface than by SBP and SPI alone, indicating that a more compact interfacial network was formed. Flocculation of oil droplets was observed and corresponding emulsion gels exhibited lower fracture force and strain when the oil was emulsified by SPI and SBP/SPI complex. Moreover, emulsion gels with small droplets produced a greater quantity of small fragments after mastication. However, microstructure did not have a significant effect on breakdown properties of emulsion gels. Headspace gas chromatography analysis showed that the release rate of ethyl butyrate before and after mastication was significantly lower in emulsion gel with more compact network, but the release of aroma compounds with higher hydrophobicity did not show a significant influence of the microstructure and texture of emulsion gel. This finding provides a useful application for designing semi-solid foods with desirable flavor perception. © 2016 Society of Chemical Industry. © 2016 Society of Chemical Industry.

  15. Moving beyond quantity of participation in process evaluation of an intervention to prevent excessive pregnancy weight gain

    Directory of Open Access Journals (Sweden)

    Paul Keriann H

    2013-02-01

    Full Text Available Abstract Background Few lifestyle interventions have successfully prevented excessive gestational weight gain. Understanding the program processes through which successful interventions achieve outcomes is important for the design of effective programs. The objective of this study was to evaluate the effect of the quantity and quality of participation in a healthy lifestyle intervention on risk of excessive gestational weight gain. Findings Pregnant women (N = 179 received five newsletters about weight, nutrition, and exercise plus postcards on which they were asked to set related goals and return to investigators. The quantity of participation (dose was defined as low for returning few or some vs. high for many postcards (N = 89, 49.7%. Quality of participation was low for setting few vs. high for some or many appropriate goals (N = 92, 51.4%. Fisher’s exact tests and multivariate logistic regression were used to analyze the effect of participation variables on the proportion with excessive weight gain. Quantity and quality of participation alone were each not significantly associated with excessive gestational weight gain, while quality of participation among those with high-levels of participation approached significance (p = 0.07. The odds of gaining excessively was decreased when women had both a high quantity and quality of participation (OR = 0.04, 95% CI = 0.005, 0.30. Conclusions Both quantity and quality of participation are important program process measures in evaluations of lifestyle interventions to promote healthy weight gain during pregnancy.

  16. Decontamination for free release

    Energy Technology Data Exchange (ETDEWEB)

    Simpson, K A; Elder, G R [Bradtec Ltd., Bristol (United Kingdom)

    1997-02-01

    Many countries are seeking to treat radioactive waste in ways which meet the local regulatory requirements, but yet are cost effective when all contributing factors are assessed. In some countries there are increasing amounts of waste, arising from nuclear plant decommissioning, which are categorized as low level waste: however with suitable treatment a large part of such wastes might become beyond regulatory control and be able to be released as non-radioactive. The benefits and disadvantages of additional treatment before disposal need to be considered. Several processes falling within the overall description of decontamination for free release have been developed and applied, and these are outlined. In one instance the process seeks to take advantage of techniques and equipment used for decontaminating water reactor circuits intermittently through reactor life. (author). 9 refs, 1 fig., 3 tabs.

  17. Atmospheric Release Advisory Capability

    International Nuclear Information System (INIS)

    Dickerson, M.H.; Gudiksen, P.H.; Sullivan, T.J.

    1983-02-01

    The Atmospheric Release Advisory Capability (ARAC) project is a Department of Energy (DOE) sponsored real-time emergency response service available for use by both federal and state agencies in case of a potential or actual atmospheric release of nuclear material. The project, initiated in 1972, is currently evolving from the research and development phase to full operation. Plans are underway to expand the existing capability to continuous operation by 1984 and to establish a National ARAC Center (NARAC) by 1988. This report describes the ARAC system, its utilization during the past two years, and plans for its expansion during the next five to six years. An integral part of this expansion is due to a very important and crucial effort sponsored by the Defense Nuclear Agency to extend the ARAC service to approximately 45 Department of Defense (DOD) sites throughout the continental US over the next three years

  18. Border cell release

    DEFF Research Database (Denmark)

    Mravec, Jozef

    2017-01-01

    Plant border cells are specialised cells derived from the root cap with roles in the biomechanics of root growth and in forming a barrier against pathogens. The mechanism of highly localised cell separation which is essential for their release to the environment is little understood. Here I present...... in situ analysis of Brachypodium distachyon, a model organism for grasses which possess type II primary cell walls poor in pectin content. Results suggest similarity in spatial dynamics of pectic homogalacturonan during dicot and monocot border cell release. Integration of observations from different...... species leads to the hypothesis that this process most likely does not involve degradation of cell wall material but rather employs unique cell wall structural and compositional means enabling both the rigidity of the root cap as well as detachability of given cells on its surface....

  19. Energy released in fission

    International Nuclear Information System (INIS)

    James, M.F.

    1969-05-01

    The effective energy released in and following the fission of U-235, Pu-239 and Pu-241 by thermal neutrons, and of U-238 by fission spectrum neutrons, is discussed. The recommended values are: U-235 ... 192.9 ± 0.5 MeV/fission; U-238 ... 193.9 ± 0.8 MeV/fission; Pu-239 ... 198.5 ± 0.8 MeV/fission; Pu-241 ... 200.3 ± 0.8 MeV/fission. These values include all contributions except from antineutrinos and very long-lived fission products. The detailed contributions are discussed, and inconsistencies in the experimental data are pointed out. In Appendix A, the contribution to the total useful energy release in a reactor from reactions other than fission are discussed briefly, and in Appendix B there is a discussion of the variations in effective energy from fission with incident neutron energy. (author)

  20. Assessment of Sleep Quantity and Sleep Disturbances During Recovery From Sports-Related Concussion in Youth Athletes.

    Science.gov (United States)

    Murdaugh, Donna L; Ono, Kim E; Reisner, Andrew; Burns, Thomas G

    2018-05-01

    To determine the relation between sleep quantity and sleep disturbances on symptoms and neurocognitive ability during the acute phase (sports-related concussion (SRC; >21d). Prospective inception cohort study. General community setting of regional middle and high schools. A sample (N=971) including youth athletes with SRC (n=528) and controls (n=443) (age, 10-18y). Not applicable. Athletes completed the Immediate Post-Concussion Assessment and Cognitive Testing battery. Partial correlation analyses and independent t tests were conducted to assess sleep quantity the night before testing. Multivariate analysis of covariance was used to assess sleep disturbances and their interaction with age. Less sleep quantity was correlated with greater report of cognitive (P=.001) and neuropsychological (P=.024) symptoms specific to prolonged recovery from SRC. Sleep disturbances significantly affect each migraine, cognitive, and neuropsychological symptoms (Psleep disturbances and age (P=.04) at >21 days post-SRC. Findings emphasize that the continued presence of low sleep quantity and sleep disturbances in youth athletes with SRC should be a specific indicator to health professionals that these athletes are at an increased risk of protracted recovery. Further research should identify additional factors that may interact with sleep to increase the risk of protracted recovery. Copyright © 2018 American Congress of Rehabilitation Medicine. Published by Elsevier Inc. All rights reserved.

  1. [Dynamics of change of ureaplasma laboratory strain titers and quantity of their DNA in transport medium at varying temperature].

    Science.gov (United States)

    Gamova, N A; Ivanova, T A

    2013-01-01

    Study of preservation dynamics of ureaplasma laboratory strain live cultures and their DNA in transport medium at varying temperature. The study was carried out in laboratory strains Ureaplasma urealyticum serotype 8 and Ureaplasma parvum serotype 1. The quantity of live ureaplasmas was determined by method of tenfold dilutions in liquid medium. The growth of ureaplasmas was registered by changes in the color of the cultivation medium due to its alkalization by metabolism products and expressed in CCU/ml. DNA quantity in samples was determined by real time PCR performed by using Florocenosis-micoplasmas-FL test system produced by ILS. Live ureaplasmas wer shown to be preserved in transport medium at 4 degrees C for 12 - 29 days, at 18 - 22 degrees C--for 9 - 20 days and at 37 degrees C--for only 2 days. In samples incubated at 37 degrees C the quantity of live ureaplasmas increased and then sharply decreased to 0, at lower temperature titers of the cells decreased smoothly. The quantity of ureaplasma DNA in the process of their incubation did not change significantly. Fundamental differences in the duration of survival of U. urealyticum strain and U. parvum strain in transport medium at varying temperature were not detected. Based on the studies performed a practical conclusion can be drawn that in cases of emergency when clinical material transportation is necessary its storage in transport medium for several days is acceptable.

  2. Slow-release fertilizer

    Science.gov (United States)

    Ming, Douglas W.; Golden, D. C.

    1992-10-01

    A synthetic apatite containing agronutrients and a method for making the apatite are disclosed. The apatite comprises crystalline calcium phosphate having agronutrients dispersed in the crystalline structure. The agronutrients can comprise potassium, magnesium, sulfur, iron, manganese, molybdenum, chlorine, boron, copper and zinc in amounts suited for plant growth. The apatite can optionally comprise a carbonate and/or silicon solubility control agent. The agronutrients are released slowly as the apatite dissolves.

  3. EIA new releases

    International Nuclear Information System (INIS)

    1994-12-01

    This report was prepared by the Energy Information Administration. It contains news releases on items of interest to the petroleum, coal, nuclear, electric and alternate fuels industries ranging from economic outlooks to environmental concerns. There is also a listing of reports by industry and an energy education resource listing containing sources for free or low-cost energy-related educational materials for educators and primary and secondary students

  4. Atmospheric release advisory capability

    International Nuclear Information System (INIS)

    Sullivan, T.J.

    1981-01-01

    The ARAC system (Atmospheric Release Advisory Capability) is described. The system is a collection of people, computers, computer models, topographic data and meteorological input data that together permits a calculation of, in a quasi-predictive sense, where effluent from an accident will migrate through the atmosphere, where it will be deposited on the ground, and what instantaneous and integrated dose an exposed individual would receive

  5. Slow-release fertilizer

    Science.gov (United States)

    Ming, Douglas W. (Inventor); Golden, Dadigamuwage C. (Inventor)

    1995-01-01

    A synthetic apatite containing agronutrients and a method for making the apatite are disclosed. The apatite comprises crystalline calcium phosphate having agronutrients dispersed in the crystalline structure. The agronutrients can comprise potassium, magnesium, sulfur, iron, manganese, molybdenum, chlorine, boron, copper and zinc in amounts suited for plant growth. The apatite can optionally comprise a carbonate and/or silicon solubility control agent. The agronutrients are released slowly as the apatite dissolves.

  6. Emergency planning and preparedness for the deliberate release of toxic industrial chemicals.

    Science.gov (United States)

    Russell, David; Simpson, John

    2010-03-01

    Society in developed and developing countries is hugely dependent upon chemicals for health, wealth, and economic prosperity, with the chemical industry contributing significantly to the global economy. Many chemicals are synthesized, stored, and transported in vast quantities and classified as high production volume chemicals; some are recognized as being toxic industrial chemicals (TICs). Chemical accidents involving chemical installations and transportation are well recognized. Such chemical accidents occur with relative frequency and may result in large numbers of casualties with acute and chronic health effects as well as fatalities. The large-scale production of TICs, the potential for widespread exposure and significant public health impact, together with their relative ease of acquisition, makes deliberate release an area of potential concern. The large numbers of chemicals, together with the large number of potential release scenarios means that the number of possible forms of chemical incident are almost infinite. Therefore, prior to undertaking emergency planning and preparedness, it is necessary to prioritize risk and subsequently mitigate. This is a multi-faceted process, including implementation of industrial protection layers, substitution of hazardous chemicals, and relocation away from communities. Residual risk provides the basis for subsequent planning. Risk-prioritized emergency planning is a tool for identifying gaps, enhancing communication and collaboration, and for policy development. It also serves to enhance preparedness, a necessary prelude to preventing or mitigating the public health risk to deliberate release. Planning is an iterative and on-going process that requires multi-disciplinary agency input, culminating in the formation of a chemical incident plan complimentary to major incident planning. Preparedness is closely related and reflects a state of readiness. It is comprised of several components, including training and exercising

  7. Radiation Exposure Decreases the Quantity and Quality of Cardiac Stem Cells in Mice

    Science.gov (United States)

    Luo, Lan; Urata, Yoshishige; Yan, Chen; Hasan, Al Shaimaa; Goto, Shinji; Guo, Chang-Ying; Tou, Fang-Fang; Xie, Yucai; Li, Tao-Sheng

    2016-01-01

    Radiation exposure may increase cardiovascular disease risks; however, the precise molecular/cellular mechanisms remain unclear. In the present study, we examined the hypothesis that radiation impairs cardiac stem cells (CSCs), thereby contributing to future cardiovascular disease risks. Adult C57BL/6 mice were exposed to 3 Gy γ-rays, and heart tissues were collected 24 hours later for further experiments. Although c-kit-positive cells were rarely found, radiation exposure significantly induced apoptosis and DNA damage in the cells of the heart. The ex vivo expansion of CSCs from freshly harvested atrial tissues showed a significantly lower production of CSCs in irradiated mice compared with healthy mice. The proliferative activity of CSCs evaluated by Ki-67 expression was not significantly different between the groups. However, compared to the healthy control, CSCs expanded from irradiated mice showed significantly lower telomerase activity, more 53BP1 foci in the nuclei, lower expression of c-kit and higher expression of CD90. Furthermore, CSCs expanded from irradiated mice had significantly poorer potency in the production of insulin-like growth factor-1. Our data suggest that radiation exposure significantly decreases the quantity and quality of CSCs, which may serve as sensitive bio-parameters for predicting future cardiovascular disease risks. PMID:27195709

  8. Radiation Exposure Decreases the Quantity and Quality of Cardiac Stem Cells in Mice.

    Directory of Open Access Journals (Sweden)

    Lan Luo

    Full Text Available Radiation exposure may increase cardiovascular disease risks; however, the precise molecular/cellular mechanisms remain unclear. In the present study, we examined the hypothesis that radiation impairs cardiac stem cells (CSCs, thereby contributing to future cardiovascular disease risks. Adult C57BL/6 mice were exposed to 3 Gy γ-rays, and heart tissues were collected 24 hours later for further experiments. Although c-kit-positive cells were rarely found, radiation exposure significantly induced apoptosis and DNA damage in the cells of the heart. The ex vivo expansion of CSCs from freshly harvested atrial tissues showed a significantly lower production of CSCs in irradiated mice compared with healthy mice. The proliferative activity of CSCs evaluated by Ki-67 expression was not significantly different between the groups. However, compared to the healthy control, CSCs expanded from irradiated mice showed significantly lower telomerase activity, more 53BP1 foci in the nuclei, lower expression of c-kit and higher expression of CD90. Furthermore, CSCs expanded from irradiated mice had significantly poorer potency in the production of insulin-like growth factor-1. Our data suggest that radiation exposure significantly decreases the quantity and quality of CSCs, which may serve as sensitive bio-parameters for predicting future cardiovascular disease risks.

  9. Contact: Releasing the news

    Science.gov (United States)

    Pinotti, Roberto

    The problem of mass behavior after man's future contacts with other intelligences in the universe is not only a challenge for social scientists and political leaders all over the world, but also a cultural time bomb as well. In fact, since the impact of CETI (Contact with Extraterrestrial Intelligence) on human civilization, with its different cultures, might cause a serious socio-anthropological shock, a common and predetermined worldwide strategy is necessary in releasing the news after the contact, in order to keep possible manifestations of fear, panic and hysteria under control. An analysis of past studies in this field and of parallel historical situations as analogs suggests a definite "authority crisis" in the public as a direct consequence of an unexpected release of the news, involving a devastating "chain reaction" process (from both the psychological and sociological viewpoints) of anomie and maybe the collapse of today's society. The only way to prevent all this is to prepare the world's public opinion concerning contact before releasing the news, and to develop a long-term strategy through the combined efforts of scientists, political leaders, intelligence agencies and the mass media, in order to create the cultural conditions in which a confrontation with ETI won't affect mankind in a traumatic way. Definite roles and tasks in this multi-level model are suggested.

  10. Analysis of hydrogen sulfide releases in heavy water production facilities

    International Nuclear Information System (INIS)

    Croitoru, Cornelia; Dumitrescu, Maria; Preda, Irina; Lazar, Roxana

    1996-01-01

    Safety analyses conducted at ICIS concern primarily the heavy water production installations. The quantitative risk assessment needs the frequency calculation of accident sequences and consequences. In heavy water plants which obtain primary isotopic concentration of water by H 2 O - H 2 S exchange, large amounts of hydrogen sulfide which is a toxic, inflammable and explosive gas, are circulated. The first stage in calculating the consequences consists in potential analysis of H 2 S release. This work presents a study of this types of releases for pilot installations of the heavy water production at ICIS (Plant 'G' at Rm. Valcea). The installations which contain and maneuver large quantities of H 2 S and the mathematical models for different types of releases are presented. The accidents analyzed are: catastrophic column, container, spy-hole failures or gas-duct rupture and wall cracks in the installation. The main results are given as tables while the time variations of the flow rate and quantities of H 2 O released by stack disposal are plotted

  11. Polyester Textiles as a Source of Microplastics from Households: A Mechanistic Study to Understand Microfiber Release During Washing.

    Science.gov (United States)

    Hernandez, Edgar; Nowack, Bernd; Mitrano, Denise M

    2017-06-20

    Microplastic fibers make up a large proportion of microplastics found in the environment, especially in urban areas. There is good reason to consider synthetic textiles a major source of microplastic fibers, and it will not diminish since the use of synthetic fabrics, especially polyester, continues to increase. In this study we provide quantitative data regarding the size and mass of microplastic fibers released from synthetic (polyester) textiles during simulated home washing under controlled laboratory conditions. Consideration of fabric structure and washing conditions (use of detergents, temperature, wash duration, and sequential washings) allowed us to study the propensity of fiber shedding in a mechanistic way. Thousands of individual fibers were measured (number, length) from each wash solution to provide a robust data set on which to draw conclusions. Among all the variables tested, the use of detergent appeared to affect the total mass of fibers released the most, yet the detergent composition (liquid or powder) or overdosing of detergent did not significantly influence microplastic release. Despite different release quantities due to the addition of a surfactant (approximately 0.025 and 0.1 mg fibers/g textile washed, without and with detergent, respectively), the overall microplastic fiber length profile remained similar regardless of wash condition or fabric structure, with the vast majority of fibers ranging between 100 and 800 μm in length irrespective of wash cycle number. This indicates that the fiber staple length and/or debris encapsulated inside the fabric from the yarn spinning could be directly responsible for releasing stray fibers. This study serves as a first look toward understanding the physical properties of the textile itself to better understand the mechanisms of fiber shedding in the context of microplastic fiber release into laundry wash water.

  12. Model calculations of the quantities of landfill gas, emitted from the landfill for solid domestic waste in Blagoevgrad (village of Buchino)

    International Nuclear Information System (INIS)

    Tzekova, Stefka; Ganev, Ivailo; Dimitrov, Boyan

    2009-01-01

    The biogas released from the landfills has got a noxious effect. It also creates the most serious environmental problems after the landfills closing. The gas releases actively for more than 25 years. That is why extremely high requirements for its utilization have been set today. The first step in this direction is the determination of its amounts. A prognosis for the quantities of gas released from the landfill at the village of Buchino has been made in the present report. The used mathematical model of prognosis has been adapted for the conditions in Bulgaria on the basis of the authors’ experience gained during their observations and research of a number of landfills in the country Keywords: landfill gas, biogas, RES

  13. Macroscopic calculational model of fission gas release from water reactor fuels

    International Nuclear Information System (INIS)

    Uchida, Masaki

    1993-01-01

    Existing models for estimating fission gas release rate usually have fuel temperature as independent variable. Use of fuel temperature, however, often brings an excess ambiguity in the estimation because it is not a rigorously definable quantity as a function of heat generation rate and burnup. To derive a mathematical model that gives gas release rate explicitly as a function of design and operational parameters, the Booth-type diffusional model was modified by changing the character of the diffusion constant from physically meaningful quantity into a mere mathematical parameter, and also changing its temperature dependency into power dependency. The derived formula was found, by proper choice of arbitrary constants, to satisfactorily predict the release rates under a variety of irradiation histories up to a burnup of 60,000 MWd/t. For simple power histories, the equation can be solved analytically by defining several transcendental functions, which enables simple calculation of release rate using graphs. (author)

  14. Protecting privacy in data release

    CERN Document Server

    Livraga, Giovanni

    2015-01-01

    This book presents a comprehensive approach to protecting sensitive information when large data collections are released by their owners. It addresses three key requirements of data privacy: the protection of data explicitly released, the protection of information not explicitly released but potentially vulnerable due to a release of other data, and the enforcement of owner-defined access restrictions to the released data. It is also the first book with a complete examination of how to enforce dynamic read and write access authorizations on released data, applicable to the emerging data outsou

  15. Triggered Release from Polymer Capsules

    Energy Technology Data Exchange (ETDEWEB)

    Esser-Kahn, Aaron P. [Univ. of Illinois, Urbana, IL (United States). Beckman Inst. for Advanced Science and Technology and Dept. of Chemistry; Odom, Susan A. [Univ. of Illinois, Urbana, IL (United States). Beckman Inst. for Advanced Science and Technology and Dept. of Chemistry; Sottos, Nancy R. [Univ. of Illinois, Urbana, IL (United States). Beckman Inst. for Advanced Science and Technology and Dept. of Materials Science and Engineering; White, Scott R. [Univ. of Illinois, Urbana, IL (United States). Beckman Inst. for Advanced Science and Technology and Dept. of Aerospace Engineering; Moore, Jeffrey S. [Univ. of Illinois, Urbana, IL (United States). Beckman Inst. for Advanced Science and Technology and Dept. of Chemistry

    2011-07-06

    Stimuli-responsive capsules are of interest in drug delivery, fragrance release, food preservation, and self-healing materials. Many methods are used to trigger the release of encapsulated contents. Here we highlight mechanisms for the controlled release of encapsulated cargo that utilize chemical reactions occurring in solid polymeric shell walls. Triggering mechanisms responsible for covalent bond cleavage that result in the release of capsule contents include chemical, biological, light, thermal, magnetic, and electrical stimuli. We present methods for encapsulation and release, triggering methods, and mechanisms and conclude with our opinions on interesting obstacles for chemically induced activation with relevance for controlled release.

  16. Reporting releases of hazardous substances under CERCLA and EPCRA

    International Nuclear Information System (INIS)

    Dailey, R.

    1990-04-01

    Several federal environmental laws requires that ''release of hazardous substances to the environment'' above certain threshold amounts -- Reportable Quantities or RQs -- be reported. Current and proposed regulations under these statutes are unclear and make full compliance difficult. Nevertheless, failure to comply could result in civil or criminal penalties. In response to questions raised by several DOE Field Elements, this Information Brief is part of a series that will provide updated information on this and other CERCLA issues. The Environmental Guidance Division (EH-231) has responded to those questions relating the reporting of releases for which EPA has a clearly articulated position. EPA's position on other questions raised by Field Elements has been equivocal; DOE is working with EPA to resolve these outstanding issues. Additional information briefs on reporting releases will be issued as a clear position is defined

  17. Dry washing: the solution for contaminated liquid effluent releases

    International Nuclear Information System (INIS)

    L'homme, D.; Trambouze, P.

    1998-01-01

    The release of wash water used for contaminated garments poses an ever-increasing problem on nuclear sites. Even though the radioactivity is low, it mixes with organic compounds, thus polluting a large quantity of liquid effluents. In many cases, several thousands of m 3 /year per nuclear site are produced, which at times represents more than 30% of the volume of total releases. The conventional dry cleaning process is not a viable option, given that repeated washing cause clothes to fade and the odors are rot removed completely. In order to eliminate releases, STMI has developed, after several years of research with the Technological University of Compiegne, France, a solvent dry washing process for garments used in the nuclear industry. (author)

  18. Evaluation of minimum quantity lubrication grinding with nano-particles and recent related patents.

    Science.gov (United States)

    Li, Changhe; Wang, Sheng; Zhang, Qiang; Jia, Dongzhou

    2013-06-01

    In recent years, a large number of patents have been devoted to developing minimum quantity lubrication (MQL) grinding techniques that can significantly improve both environmentally conscious and energy saving and costeffective sustainable grinding fluid alternatives. Among them, one patent is about a supply system for the grinding fluid in nano-particle jet MQL, which produced MQL lubricant by adding solid nano-particles in degradable grinding fluid. The MQL supply device turns the lubricant to the pulse drops with fixed pressure, unchanged pulse frequency and the same drop diameter. The drops will be produced and injected in the grinding zone in the form of jet flow under high pressure gas and air seal. As people become increasingly demanding on our environment, minimum quantity lubrication has been widely used in the grinding and processing. Yet, it presents the defect of insufficient cooling performance, which confines its development. To improve the heat transfer efficiency of MQL, nano-particles of a certain mass fraction can be added in the minimum quantity of lubricant oil, which concomitantly will improve the lubrication effects in the processing. In this study, the grinding experiment corroborated the effect of nano-particles in surface grinding. In addition, compared with other forms of lubrication, the results presented that the grinding force, the friction coefficient and specific grinding energy of MQL grinding have been significantly weakened, while G ratio greatly rose. These are attributed to the friction oil-film with excellent anti-friction and anti-wear performance, which is generated nano-particles at the wheel/workpiece interface. In this research, the cooling performance of nano-particle jet MQL was analyzed. Based on tests and experiments, the surface temperature was assayed from different methods, including flood lubricating oil, dry grinding, MQL grinding and nano-particle jet MQL grinding. Because of the outstanding heat transfer

  19. Quantity and/or Quality? The Importance of Publishing Many Papers

    Science.gov (United States)

    van den Besselaar, Peter

    2016-01-01

    Do highly productive researchers have significantly higher probability to produce top cited papers? Or do high productive researchers mainly produce a sea of irrelevant papers—in other words do we find a diminishing marginal result from productivity? The answer on these questions is important, as it may help to answer the question of whether the increased competition and increased use of indicators for research evaluation and accountability focus has perverse effects or not. We use a Swedish author disambiguated dataset consisting of 48.000 researchers and their WoS-publications during the period of 2008–2011 with citations until 2014 to investigate the relation between productivity and production of highly cited papers. As the analysis shows, quantity does make a difference. PMID:27870854

  20. Effect of pilot fuel quantity on the performance of a dual fuel engine

    Energy Technology Data Exchange (ETDEWEB)

    Abd Alla, G.H.; Soliman, H.A.; Badr, O.A.; Abd Rabbo, M.F. [Zagazig University, Cairo (Egypt). Shoubra Faculty of Engineering

    2000-04-01

    It is well known that the operation of dual fuel engines at lower loads suffers from lower thermal efficiency and higher unburned percentages of fuel. To rectify this problem, tests have been conducted on a special single cylinder compression ignition research engine (Ricardo E6) to investigate the effect of pilot fuel quantity on the performance of an indirect injection diesel engine fuelled with gaseous fuel. Diesel fuel was used as the pilot fuel and methane or propane was used as the main fuel which was inducted into the intake manifold to mix with the intake air. Through experimental investigations, it is shown that, the low efficiency and excess emissions at light loads can be improved significantly by increasing the amount of pilot fuel, while increasing the amount of pilot fuel at high loads led to early knocking. (author)

  1. Amending greenroof soil with biochar to affect runoff water quantity and quality.

    Science.gov (United States)

    Beck, Deborah A; Johnson, Gwynn R; Spolek, Graig A

    2011-01-01

    Numbers of greenroofs in urban areas continue to grow internationally; so designing greenroof soil to reduce the amount of nutrients in the stormwater runoff from these roofs is becoming essential. This study evaluated changes in extensive greenroof water discharge quality and quantity after adding biochar, a soil amendment promoted for its ability to retain nutrients in soils and increase soil fertility. Prototype greenroof trays with and without biochar were planted with sedum or ryegrass, with barren soil trays used as controls. The greenroof trays were subjected to two sequential 7.4cm/h rainfall events using a rain simulator. Runoff from the rain events was collected and evaluated. Trays containing 7% biochar showed increased water retention and significant decreases in discharge of total nitrogen, total phosphorus, nitrate, phosphate, and organic carbon. The addition of biochar to greenroof soil improves both runoff water quality and retention. Copyright © 2011 Elsevier Ltd. All rights reserved.

  2. Quality and Quantity of Sorghum Hydroponic Fodder from Different Varieties and Harvest Time

    Science.gov (United States)

    Chrisdiana, R.

    2018-02-01

    This experiment was designed to compare different varieties and harvest time of sorghum hydroponic fodder based on nutrient content and biomass production. Experimental design for fodder productivity was completely randomized design with 2 x 3 factorial, i.e., sorghum varieties (KD 4 and Super-1) and time of harvesting the sorghum hydroponic fodder (8,12 and 16 d). Total biomass and DM production, were affected significantly (p<0.05) on harvest time. Total biomass and nutrient content were increased in longer harvest time. The nutrient content were increased with decreasing total value of DM. Super-1 varieties produce larger biomass and nutrient content higher than KD4 (p<0.05). Based on sorghum hidroponic fodder quality and quantity, sorghum hidroponic fodder with Super-1 varieties harvested at 12 d had a good quality of fodder and it can be alternative of technology providing quality forage and land saving with a short time planting period and continous production.

  3. Quantity-Quality and the One Child Policy:The Only-Child Disadvantage in School Enrollment in Rural China

    OpenAIRE

    Nancy Qian

    2009-01-01

    Many believe that increasing the quantity of children will lead to a decrease in their quality. This paper exploits plausibly exogenous changes in family size caused by relaxations in China's One Child Policy to estimate the causal effect of family size on school enrollment of the first child. The results show that for one-child families, an additional child significantly increased school enrollment of first-born children by approximately 16 percentage-points. The effect is larger for househo...

  4. [Characteristics of dissolved organic carbon release under inundation from typical grass plants in the water-level fluctuation zone of the Three Gorges Reservoir area].

    Science.gov (United States)

    Tan, Qiu-Xia; Zhu, Boi; Hua, Ke-Ke

    2013-08-01

    The water-level fluctuation zone of the Three Gorges Reservoir (TGR) exposes in spring and summer, then, green plants especially herbaceous plants grow vigorously. In the late of September, water-level fluctuation zone of TGR goes to inundation. Meanwhile, annually accumulated biomass of plant will be submerged for decaying, resulting in organism decomposition and release a large amount of dissolved organic carbon (DOC). This may lead to negative impacts on water environment of TGR. The typical herbaceous plants from water-level fluctuation zone were collected and inundated in the laboratory for dynamic measurements of DOC concentration of overlying water. According to the determination, the DOC release rates and fluxes have been calculated. Results showed that the release process of DOC variation fitted in a parabolic curve. The peak DOC concentrations emerge averagely in the 15th day of inundation, indicating that DOC released quickly with organism decay of herbaceous plant. The release process of DOC could be described by the logarithm equation. There are significant differences between the concentration of DOC (the maximum DOC concentration is 486.88 mg x L(-1) +/- 35.97 mg x L(-1) for Centaurea picris, the minimum is 4.18 mg x L(-1) +/- 1.07 mg x L(-1) for Echinochloacrus galli) and the release amount of DOC (the maximum is 50.54 mg x g(-1) for Centaurea picris, the minimum is 6.51 mg x g(-1) for Polygonum hydropiper) due to different characteristics of plants, especially, the values of C/N of herbaceous plants. The cumulative DOC release quantities during the whole inundation period were significantly correlated with plants' C/N values in linear equations.

  5. Stimulatory effects of neuronally released norepinephrine on renin release in vitro

    Energy Technology Data Exchange (ETDEWEB)

    Matsumura, Yasuo; Kawazoe, Shinka; Ichihara, Toshio; Shinyama, Hiroshi; Kageyama, Masaaki; Morimoto, Shiro (Osaka Univ. of Pharmaceutical Sciences (Japan))

    1988-10-01

    Extracellular high potassium inhibits renin release in vitro by increasing calcium concentrations in the juxtaglomerular cells. The authors found that the decreased response of renin release from rat kidney cortical slices in high potassium solution changed to a strikingly increased one in the presence of nifedipine at doses over 10{sup {minus}6} M. They then examined the stimulatory effect of extracellular high potassium in the presence of nifedipine on renin release. The enhancement of release was significantly suppressed either by propranolol or by metoprolol but not by prazosin. High potassium plus nifedipine-induced increase in renin release was markedly attenuated by renal denervation. The enhancing effect was not observed when the slices were incubated in calcium-free medium. Divalent cations such as Cd{sup 2+}, Co{sup 2+}, and Mn{sup 2+} blocked this enhancement in a concentration-dependent manner. High potassium elicited an increase in {sup 3}H efflux from the slices preloaded with ({sup 3}H)-norepinephrine. The increasing effect was not influenced by nifedipine but was abolished by the removal of extracellular calcium or by the addition of divalent cations. These observations suggest to us that the high potassium plus nifedipine-induced increase in renin release from the slices is mediated by norepinephrine derived from renal sympathetic nerves and that this neuronally released norepinephrine stimulates renin release via activation of {beta}-adrenoceptors.

  6. Quality evaluation of extemporaneous delayed-release liquid formulations of lansoprazole.

    Science.gov (United States)

    Melkoumov, Alexandre; Soukrati, Amina; Elkin, Igor; Forest, Jean-Marc; Hildgen, Patrice; Leclair, Grégoire

    2011-11-01

    The quality attributes of extemporaneous delayed-release liquid formulations of lansoprazole for oral administration were evaluated. A novel liquid formulation (3 mg/mL) of Prevacid FasTab in an Ora-Blend vehicle was prepared and compared with the Prevacid FasTab 30 mg and Prevacid-sodium bicarbonate 1 M formulation (3 mg/mL). The latter formulation was combined with hydrochloric acid 0.1 N, and the remaining lansoprazole content was assayed by high-performance liquid chromatography (HPLC). A batch of delayed-release liquid formulation was prepared to evaluate content uniformity. For content assay, three samples were prepared for each evaluated condition and each sample was analyzed in triplicate by HPLC. The lansoprazole in the sodium bicarbonate formulation was extensively degraded by quantities of hydrochloric acid 0.1 N in excess of 100 mL. Storage time and temperature had a significant effect on lansoprazole stability in the Ora-Blend formulation. The drug remained stable for seven days when the formulation was stored at 4.5-5.5 °C, but storage at 21-22 °C or the reduction of pH with citric acid accelerated lansoprazole degradation. The amount of lansoprazole released from the Ora-Blend formulation during the buffer stage of the dissolution test decreased with increases in formulation storage time, in formulation storage temperature, and in the amount of lansoprazole released and degraded during the acid stage of the test. An extemporaneous formulation consisting of lansoprazole microgranules in Ora-Blend maintained acceptable quality attributes when stored for three days at 4.5-5.5 °C.

  7. Changes in sleep quantity and efficiency in professional rugby union players during home based training and match-play.

    Science.gov (United States)

    Eagles, A; Mclellan, C; Hing, W; Carloss, N; Lovell, D

    2014-11-04

    Adequate sleep is paramount to athlete recovery and performance, however little is know about the typical sleep patterns of professional rugby union players during home based training and match-play in the competitive season. The aim of the present study was to monitor changes in sleep quantity and efficiency of elite male rugby union players over a twelve night period, which included training and two competitive matches. A total of ten elite male rugby union players from a selected team, participated in the study. Athletes sleep quantity and efficiency was monitored over a twelve night period using the Bodymedia sensewear units (BSU). There was a significant difference in sleep quantity (pwake over the twelve night period. Sleep efficiency is defined as a percentage score calculated by incorporating movement and physiological measures over the sleep duration as determined by the BSU. Also there was no significant difference between sleep parameters on the game nights. The findings show players have significantly (p<0.05) reduced sleep following a home game, which is of concern considering the established negative influence of sleep deprivation on cognitive and physical performance. This data may assist coaching, medical and performance staff to develop and implement team and individualised sleep monitoring regimes to optimise training and on-field performance.

  8. Memory for multiple cache locations and prey quantities in a food-hoarding songbird

    Directory of Open Access Journals (Sweden)

    Nicola eArmstrong

    2012-12-01

    Full Text Available Most animals can discriminate between pairs of numbers that are each less than four without training. However, North Island robins (Petroica longipes, a food hoarding songbird endemic to New Zealand, can discriminate between quantities of items as high as eight without training. Here we investigate whether robins are capable of other complex quantity discrimination tasks. We test whether their ability to discriminate between small quantities declines with 1. the number of cache sites containing prey rewards and 2. the length of time separating cache creation and retrieval (retention interval. Results showed that subjects generally performed above chance expectations. They were equally able to discriminate between different combinations of prey quantities that were hidden from view in 2, 3 and 4 cache sites from between 1, 10 and 60 seconds. Overall results indicate that North Island robins can process complex quantity information involving more than two discrete quantities of items for up to one minute long retention intervals without training.

  9. Riola release report

    Energy Technology Data Exchange (ETDEWEB)

    Woodward, E.C.

    1983-08-04

    Eleven hours after execution of the Riola Event (at 0826 PDT on 25 September 1980) in hole U2eq of the Nevada Test Site (NTS), a release of radioactivity began. When the seepage stopped at about noon the following day, up to some 3200 Ci of activity had been dispersed by light variable winds. On 26 September, examination of the geophone records showed six hours of low-level, but fairly continuous, activity before the release. Electrical measurements indicated that most cables were still intact to a depth below the stemming platform. A survey of the ground zero area showed that the seepage came through cracks between the surface conductor and the pad, through cracks in the pad, and through a crack adjacent to the pad around the mousehole (a small hole adjacent to the emplacement hole). To preclude undue radiation exposure or injury from a surprise subsidence, safety measures were instituted. Tritium seepage was suffucient to postpone site activities until a box and pipeline were emplaced to contain and remove the gas. Radiation release modeling and calculations were generally consistent with observations. Plug-hole interaction calculations showed that the alluvium near the bottom of the plug may have been overstressed and that improvements in the design of the plug-medium interface can be made. Experimental studies verified that the surface appearance of the plug core was caused by erosion, but, assuming a normal strength for the plug material, that erosion alone could not account for the disappearance of such a large portion of the stemming platform. Samples from downhole plug experiments show that the plug may have been considerably weaker than had been indicted by quality assurance (QA) samples. 19 references, 32 figures, 10 tables.

  10. Riola release report

    International Nuclear Information System (INIS)

    Woodward, E.C.

    1983-01-01

    Eleven hours after execution of the Riola Event (at 0826 PDT on 25 September 1980) in hole U2eq of the Nevada Test Site (NTS), a release of radioactivity began. When the seepage stopped at about noon the following day, up to some 3200 Ci of activity had been dispersed by light variable winds. On 26 September, examination of the geophone records showed six hours of low-level, but fairly continuous, activity before the release. Electrical measurements indicated that most cables were still intact to a depth below the stemming platform. A survey of the ground zero area showed that the seepage came through cracks between the surface conductor and the pad, through cracks in the pad, and through a crack adjacent to the pad around the mousehole (a small hole adjacent to the emplacement hole). To preclude undue radiation exposure or injury from a surprise subsidence, safety measures were instituted. Tritium seepage was suffucient to postpone site activities until a box and pipeline were emplaced to contain and remove the gas. Radiation release modeling and calculations were generally consistent with observations. Plug-hole interaction calculations showed that the alluvium near the bottom of the plug may have been overstressed and that improvements in the design of the plug-medium interface can be made. Experimental studies verified that the surface appearance of the plug core was caused by erosion, but, assuming a normal strength for the plug material, that erosion alone could not account for the disappearance of such a large portion of the stemming platform. Samples from downhole plug experiments show that the plug may have been considerably weaker than had been indicted by quality assurance (QA) samples. 19 references, 32 figures, 10 tables

  11. SU-E-T-596: P3DVHStats - a Novel, Automatic, Institution Customizable Program to Compute and Report DVH Quantities On Philips Pinnacle TPS

    International Nuclear Information System (INIS)

    Wu, C

    2015-01-01

    Purpose: To implement a novel, automatic, institutional customizable DVH quantities evaluation and PDF report tool on Philips Pinnacle treatment planning system (TPS) Methods: An add-on program (P3DVHStats) is developed by us to enable automatic DVH quantities evaluation (including both volume and dose based quantities, such as V98, V100, D2), and automatic PDF format report generation, for EMR convenience. The implementation is based on a combination of Philips Pinnacle scripting tool and Java language pre-installed on each Pinnacle Sun Solaris workstation. A single Pinnacle script provide user a convenient access to the program when needed. The activated script will first export DVH data for user selected ROIs from current Pinnacle plan trial; a Java program then provides a simple GUI interface, utilizes the data to compute any user requested DVH quantities, compare with preset institutional DVH planning goals; if accepted by users, the program will also generate a PDF report of the results and export it from Pinnacle to EMR import folder via FTP. Results: The program was tested thoroughly and has been released for clinical use at our institution (Pinnacle Enterprise server with both thin clients and P3PC access), for all dosimetry and physics staff, with excellent feedback. It used to take a few minutes to use MS-Excel worksheet to calculate these DVH quantities for IMRT/VMAT plans, and manually save them as PDF report; with the new program, it literally takes a few mouse clicks in less than 30 seconds to complete the same tasks. Conclusion: A Pinnacle scripting and Java language based program is successfully implemented, customized to our institutional needs. It is shown to dramatically reduce time and effort needed for DVH quantities computing and EMR reporting

  12. SU-E-T-596: P3DVHStats - a Novel, Automatic, Institution Customizable Program to Compute and Report DVH Quantities On Philips Pinnacle TPS

    Energy Technology Data Exchange (ETDEWEB)

    Wu, C [Sutter Medical Foundation, Roseville, CA (United States)

    2015-06-15

    Purpose: To implement a novel, automatic, institutional customizable DVH quantities evaluation and PDF report tool on Philips Pinnacle treatment planning system (TPS) Methods: An add-on program (P3DVHStats) is developed by us to enable automatic DVH quantities evaluation (including both volume and dose based quantities, such as V98, V100, D2), and automatic PDF format report generation, for EMR convenience. The implementation is based on a combination of Philips Pinnacle scripting tool and Java language pre-installed on each Pinnacle Sun Solaris workstation. A single Pinnacle script provide user a convenient access to the program when needed. The activated script will first export DVH data for user selected ROIs from current Pinnacle plan trial; a Java program then provides a simple GUI interface, utilizes the data to compute any user requested DVH quantities, compare with preset institutional DVH planning goals; if accepted by users, the program will also generate a PDF report of the results and export it from Pinnacle to EMR import folder via FTP. Results: The program was tested thoroughly and has been released for clinical use at our institution (Pinnacle Enterprise server with both thin clients and P3PC access), for all dosimetry and physics staff, with excellent feedback. It used to take a few minutes to use MS-Excel worksheet to calculate these DVH quantities for IMRT/VMAT plans, and manually save them as PDF report; with the new program, it literally takes a few mouse clicks in less than 30 seconds to complete the same tasks. Conclusion: A Pinnacle scripting and Java language based program is successfully implemented, customized to our institutional needs. It is shown to dramatically reduce time and effort needed for DVH quantities computing and EMR reporting.

  13. Effect of Food Emulsifiers on Aroma Release

    Directory of Open Access Journals (Sweden)

    Jia-Jia Li

    2016-04-01

    Full Text Available This study aimed to determine the influence of different emulsifiers or xanthan-emulsifier systems on the release of aroma compounds. Solid-phase microextraction (SPME and GC-MS were used to study the effects of varying concentrations of xanthan gum, sucrose fatty acid ester, Tween 80 and soybean lecithin on the release of seven aroma compounds. The effects of the emulsifier systems supplemented with xanthan gum on aroma release were also studied in the same way. The results showed varying degrees of influence of sucrose fatty acid ester, soybean lecithin, Tween 80 and xanthan gum on the release of aroma compounds. Compared with other aroma compounds, ethyl acetate was more likely to be conserved in the solution system, while the amount of limonene released was the highest among these seven aroma compounds. In conclusion, different emulsifiers and complexes showed different surface properties that tend to interact with different aroma molecules. The present studies showed that the composition and structure of emulsifiers and specific interactions between emulsifiers and aroma molecules have significant effects on aroma release.

  14. Tritium release from neutron irradiated beryllium pebbles

    Energy Technology Data Exchange (ETDEWEB)

    Scaffidi-Argentina, F.; Werle, H. [Forschungszentrum Karlsruhe GmbH Technik und Umwelt (Germany). Inst. fuer Neutronenphysik und Reactortechnik

    1998-01-01

    One of the most important open issues related to beryllium for fusion applications refers to the kinetics of the tritium release as a function of neutron fluence and temperature. The EXOTIC-7 as well as the `Beryllium` experiments carried out in the HFR reactor in Petten are considered as the most detailed and significant tests for investigating the beryllium response under neutron irradiation. This paper reviews the present status of beryllium post-irradiation examinations performed at the Forschungszentrum Karlsruhe with samples from the above mentioned irradiation experiments, trying to elucidate the tritium release controlling processes. In agreement with previous studies it has been found that release starts at about 500-550degC and achieves a maximum at about 700-750degC. The observed release at about 500-550degC is probably due to tritium escaping from chemical traps, while the maximum release at about 700-750degC is due to tritium escaping from physical traps. The consequences of a direct contact between beryllium and ceramics during irradiation, causing tritium implanting in a surface layer of beryllium up to a depth of about 40 mm and leading to an additional inventory which is usually several times larger than the neutron-produced one, are also presented and the effects on the tritium release are discussed. (author)

  15. Renal epithelial cells can release ATP by vesicular fusion

    Directory of Open Access Journals (Sweden)

    Randi G Bjaelde

    2013-09-01

    Full Text Available Renal epithelial cells have the ability to release nucleotides as paracrine factors. In the intercalated cells of the collecting duct, ATP is released by connexin30 (cx30, which is selectively expressed in this cell type. However, ATP is released by virtually all renal epithelia and the aim of the present study was to identify possible alternative nucleotide release pathways in a renal epithelial cell model. We used MDCK (type1 cells to screen for various potential ATP release pathways. In these cells, inhibition of the vesicular H+-ATPases (bafilomycin reduced both the spontaneous and hypotonically (80%-induced nucleotide release. Interference with vesicular fusion using N-ethylamide markedly reduced the spontaneous nucleotide release, as did interference with trafficking from the endoplasmic reticulum to the Golgi apparatus (brefeldin A1 and vesicular transport (nocodazole. These findings were substantiated using a siRNA directed against SNAP-23, which significantly reduced spontaneous ATP release. Inhibition of pannexin and connexins did not affect the spontaneous ATP release in this cell type, which consists of ∼90% principal cells. TIRF-microscopy of either fluorescently-labeled ATP (MANT-ATP or quinacrine-loaded vesicles, revealed that spontaneous release of single vesicles could be promoted by either hypoosmolality (50% or ionomycin. This vesicular release decreased the overall cellular fluorescence by 5.8% and 7.6% respectively. In summary, this study supports the notion that spontaneous and induced ATP release can occur via exocytosis in renal epithelial cells.

  16. Allegheny County Toxics Release Inventory

    Data.gov (United States)

    Allegheny County / City of Pittsburgh / Western PA Regional Data Center — The Toxics Release Inventory (TRI) data provides information about toxic substances released into the environment or managed through recycling, energy recovery, and...

  17. Progress toward forecasting product quality and quantity of mammalian cell culture processes by performance-based modeling.

    Science.gov (United States)

    Schmidberger, Timo; Posch, Christoph; Sasse, Alexandra; Gülch, Carina; Huber, Robert

    2015-01-01

    The production of biopharmaceuticals requires highly sophisticated, complex cell based processes. Once a process has been developed, acceptable ranges for various control parameters are typically defined based on process characterization studies often comprising several dozens of small scale bioreactor cultivations. A lot of data is generated during these studies and usually only the information needed to define acceptable ranges is processed in more detail. Making use of the wealth of information contained in such data sets, we present here a methodology that uses performance data (such as metabolite profiles) to forecast the product quality and quantity of mammalian cell culture processes based on a toolbox of advanced statistical methods. With this performance based modeling (PBM) the final product concentration and 12 quality attributes (QAs) for two different biopharmaceutical products were predicted in daily intervals throughout the main stage process. The best forecast was achieved for product concentration in a very early phase of the process. Furthermore, some glycan isoforms were predicted with good accuracy several days before the bioreactor was harvested. Overall, PBM clearly demonstrated its capability of early process endpoint prediction by only using commonly available data, even though it was not possible to predict all QAs with the desired accuracy. Knowing the product quality prior to the harvest allows the manufacturer to take counter measures in case the forecasted quality or quantity deviates from what is expected. This would be a big step towards real-time release, an important element of the FDA's PAT initiative. © 2015 American Institute of Chemical Engineers.

  18. Principles and foundation: national standards on quantities and units in nuclear science field

    International Nuclear Information System (INIS)

    Chen Lishu

    1993-11-01

    The main contents of National Standards on Quantities and units of atomic and nuclear physics (GB 3102.9) and Quantities and Units of nuclear reactions and ionizing radiations (GB 310.10) are presented in which most important quantities with their symbols and definitions in the nuclear scientific field are given. The principles and foundation, including the International System of Units (SI) and its application to the nuclear scientific field, in the setting of the National Standards are explained

  19. Measuring nanocurie quantities of tritium bred in metallic lithium and lithium oxide samples

    International Nuclear Information System (INIS)

    Bertone, P.C.

    1985-01-01

    The LBM program requires that nanocurie quantities of tritium, bred in both lithium oxide pellets and lithium samples, be measured with an uncertainty not exceeding + or - 6%. Two methods of accurately measuring nanocurie quantities of tritium bred in LBM lithium oxide pellets and one method of accurately measuring nanocurie quantities of tritium bred in lithium samples are described. Potential errors associated with these tritium measurement techniques are also discussed

  20. Quantity-split strategy under two-contractor competitive procurement environment

    OpenAIRE

    Boger, Dan C.; Liao, Shu S.

    1988-01-01

    This report discusses the various market scenarios that provide bid price manipulation opportunities under the dual source competition environment. Two different quantity-split strategies were developed one for the case when one of the suppliers does not have the capacity to produce the majority of the annual quantity requirement and the other for the case when neither contractor is interested in using low prices to capture the larger share of annual quantity. Keywords: Dual sourcing, Quantit...

  1. Lie-Mei symmetry and conserved quantities of the Rosenberg problem

    International Nuclear Information System (INIS)

    Liu Xiao-Wei; Li Yuan-Cheng

    2011-01-01

    The Rosenberg problem is a typical but not too complicated problem of nonholonomic mechanical systems. The Lie—Mei symmetry and the conserved quantities of the Rosenberg problem are studied. For the Rosenberg problem, the Lie and the Mei symmetries for the equation are obtained, the conserved quantities are deduced from them and then the definition and the criterion for the Lie—Mei symmetry of the Rosenberg problem are derived. Finally, the Hojman conserved quantity and the Mei conserved quantity are deduced from the Lie—Mei symmetry. (general)

  2. Lie-Mei symmetry and conserved quantities of the Rosenberg problem

    Science.gov (United States)

    Liu, Xiao-Wei; Li, Yuan-Cheng

    2011-07-01

    The Rosenberg problem is a typical but not too complicated problem of nonholonomic mechanical systems. The Lie—Mei symmetry and the conserved quantities of the Rosenberg problem are studied. For the Rosenberg problem, the Lie and the Mei symmetries for the equation are obtained, the conserved quantities are deduced from them and then the definition and the criterion for the Lie—Mei symmetry of the Rosenberg problem are derived. Finally, the Hojman conserved quantity and the Mei conserved quantity are deduced from the Lie—Mei symmetry.

  3. 76 FR 82320 - Ethyl Alcohol for Fuel Use: Determination of the Base Quantity of Imports

    Science.gov (United States)

    2011-12-30

    ... INTERNATIONAL TRADE COMMISSION [Investigation No. 332-288] Ethyl Alcohol for Fuel Use: Determination of the Base Quantity of Imports AGENCY: United States International Trade Commission. [[Page 82321

  4. [Pärtel Lippus. The acoustic features and perception of the Estonian quantity system] / Stefan Werner

    Index Scriptorium Estoniae

    Werner, Stefan

    2012-01-01

    Arvustus: Pärtel Lippus. The acoustic features and perception of the Estonian quantity system. Tartu : Tartu University Press, 2011. (Dissertationes philologiae estonicae Universitatis Tartuensis ; 29)

  5. Patterns in new dimensionless quantities containing melting temperature, and their dependence on pressure

    Directory of Open Access Journals (Sweden)

    U. WALZER

    1980-06-01

    Full Text Available The relationships existing between melting temperature and other
    macroscopic physical quantities are investigated. A new dimensionless
    quantity Q(1 not containing the Grtineisen parameter proves to be suited for serving in future studies as a tool for the determination of the melting temperature in the outer core of the Earth. The pressure dependence of more general dimensionless quantities Q„ is determined analytically and, for the chemical elements, numerically, too. The patterns of various interesting dimensionless quantities are shown in the Periodic Table and compared.

  6. Quantity assessment of waste in the dismantlement of liquid waste treatment plant and its actual state

    International Nuclear Information System (INIS)

    Uchiyama, Takafumi; Mitsuhashi, Ishi; Matsumoto, Tetsuo; Morishima, Kayoko; Tanzawa, Tomio

    2016-01-01

    From the progress of decommissioning project work of Tokyo City University Atomic Energy Research Institute, this paper reports the comparison between the actual amount of the waste generated during dismantlement work at liquid waste treatment facilities and the assessment quantity before starting the dismantlement. The quantity assessment was made on the basis of the installation license application, design specifications, drawings, records, history of use, site investigation results, etc. Since this quantity assessment did not take into account the dismantling contents of reservoir concrete, the assessed quantity of non-radioactive waste (NR waste) did not match the sum of actual NR waste. However, if an actually generated quantity of concrete of radioactive waste was added to the quantity assessment as NR waste, the quantity of actually generated NR waste and that of assessed NR waste were nearly consistent, which verified the validity of this assessment. This method is considered to be able to be utilized in the future quantity assessment of decommissioning work and the like. On the other hand, it was found that the number of drums that were actually stored tended to increase more than the estimated number of drum conversion. In old buildings, it is necessary to take into account the generation of waste other than radioactive materials in the quantity assessment stage and dismantlement stage. (A.O.)

  7. Validation of software releases for CMS

    International Nuclear Information System (INIS)

    Gutsche, Oliver

    2010-01-01

    The CMS software stack currently consists of more than 2 Million lines of code developed by over 250 authors with a new version being released every week. CMS has setup a validation process for quality assurance which enables the developers to compare the performance of a release to previous releases and references. The validation process provides the developers with reconstructed datasets of real data and MC samples. The samples span the whole range of detector effects and important physics signatures to benchmark the performance of the software. They are used to investigate interdependency effects of all CMS software components and to find and fix bugs. The release validation process described here is an integral part of CMS software development and contributes significantly to ensure stable production and analysis. It represents a sizable contribution to the overall MC production of CMS. Its success emphasizes the importance of a streamlined release validation process for projects with a large code basis and significant number of developers and can function as a model for future projects.

  8. Cobalt release from inexpensive jewellery

    DEFF Research Database (Denmark)

    Thyssen, Jacob Pontoppidan; Jellesen, Morten Stendahl; Menné, Torkil

    2010-01-01

    . Conclusions: This study showed that only a minority of inexpensive jewellery purchased in Denmark released cobalt when analysed with the cobalt spot test. As fashion trends fluctuate and we found cobalt release from dark appearing jewellery, cobalt release from consumer items should be monitored in the future......Objectives: The aim was to study 354 consumer items using the cobalt spot test. Cobalt release was assessed to obtain a risk estimate of cobalt allergy and dermatitis in consumers who would wear the jewellery. Methods: The cobalt spot test was used to assess cobalt release from all items...

  9. Denervation-Induced Activation of the Ubiquitin-Proteasome System Reduces Skeletal Muscle Quantity Not Quality.

    Science.gov (United States)

    Baumann, Cory W; Liu, Haiming M; Thompson, LaDora V

    2016-01-01

    It is well known that the ubiquitin-proteasome system is activated in response to skeletal muscle wasting and functions to degrade contractile proteins. The loss of these proteins inevitably reduces skeletal muscle size (i.e., quantity). However, it is currently unknown whether activation of this pathway also affects function by impairing the muscle's intrinsic ability to produce force (i.e., quality). Therefore, the purpose of this study was twofold, (1) document how the ubiquitin-proteasome system responds to denervation and (2) identify the physiological consequences of these changes. To induce soleus muscle atrophy, C57BL6 mice underwent tibial nerve transection of the left hindlimb for 7 or 14 days (n = 6-8 per group). At these time points, content of several proteins within the ubiquitin-proteasome system were determined via Western blot, while ex vivo whole muscle contractility was specifically analyzed at day 14. Denervation temporarily increased several key proteins within the ubiquitin-proteasome system, including the E3 ligase MuRF1 and the proteasome subunits 19S, α7 and β5. These changes were accompanied by reductions in absolute peak force and power, which were offset when expressed relative to physiological cross-sectional area. Contrary to peak force, absolute and relative forces at submaximal stimulation frequencies were significantly greater following 14 days of denervation. Taken together, these data represent two keys findings. First, activation of the ubiquitin-proteasome system is associated with reductions in skeletal muscle quantity rather than quality. Second, shortly after denervation, it appears the muscle remodels to compensate for the loss of neural activity via changes in Ca2+ handling.

  10. Water quality and quantity investigation of green roofs in a dry climate.

    Science.gov (United States)

    Beecham, S; Razzaghmanesh, M

    2015-03-01

    Low-energy pollutant removal strategies are now being sought for water sensitive urban design. This paper describes investigations into the water quality and quantity of sixteen, low-maintenance and unfertilized intensive and extensive green roof beds. The factors of Slope (1° and 25°), Depth (100 mm and 300 mm), Growing media (type A, type B and type C) and Species (P1, P2 and P3) were randomized according to a split-split plot design. This consisted of twelve vegetated green roof beds and four non-vegetated beds as controls. Stormwater runoff was collected from drainage points that were installed in each area. Samples of run-off were collected for five rainfall events and analysed for water retention capacity and the water quality parameters of NO₂, NO₃, NH₄, PO₄, pH, EC, TDS, Turbidity, Na, Ca, Mg and K. The results indicated significant differences in terms of stormwater water quality and quantity between the outflows of vegetated and non-vegetated systems. The water retention was between 51% and 96% and this range was attributed to the green roof configurations in the experiment. Comparing the quality of rainfall as inflow, and the quality of runoff from the systems showed that green roofs generally acted as a source of pollutants in this study. In the vegetated beds, the intensive green roofs performed better than the extensive beds with regard to outflow quality while in the non-vegetated beds, the extensive beds performed better than intensive systems. This highlights the importance of vegetation in improving water retention capacity as well as the role of vegetation in enhancing pollutant removal in green roof systems. In addition growing media with less organic matter had better water quality performance. Comparison of these results with national and international standards for water reuse confirmed that the green roof outflow was suitable for non-potable uses such as landscape irrigation and toilet flushing. Copyright © 2014 Elsevier Ltd. All

  11. A Little Here, A Little There, A Fairly Big Problem Everywhere: Small Quantity Site Transuranic Waste Disposition Alternatives

    International Nuclear Information System (INIS)

    Luke, Dale Elden; Parker, Douglas Wayne; Moss, J.; Monk, Thomas Hugh; Fritz, Lori Lee; Daugherty, B.; Hladek, K.; Kosiewicx, S.

    2000-01-01

    Small quantities of transuranic (TRU) waste represent a significant challenge to the waste disposition and facility closure plans of several sites in the Department of Energy (DOE) complex. This paper presents the results of a series of evaluations, using a systems engineering approach, to identify the preferred alternative for dispositioning TRU waste from small quantity sites (SQSs). The TRU waste disposition alternatives evaluation used semi-quantitative data provided by the SQSs, potential receiving sites, and the Waste Isolation Pilot Plant (WIPP) to select and recommend candidate sites for waste receipt, interim storage, processing, and preparation for final disposition of contact-handled (CH) and remote-handled (RH) TRU waste. The evaluations of only four of these SQSs resulted in potential savings to the taxpayer of $33 million to $81 million, depending on whether mobile systems could be used to characterize, package, and certify the waste or whether each site would be required to perform this work. Small quantity shipping sites included in the evaluation included the Battelle Columbus Laboratory (BCL), University of Missouri Research Reactor (MURR), Energy Technology Engineering Center (ETEC), and Mound. Candidate receiving sites included the Idaho National Engineering and Environmental Laboratory (INEEL), the Savannah River Site (SRS), Los Alamos National Laboratory (LANL), Oak Ridge (OR), and Hanford. At least 14 additional DOE sites having TRU waste may be able to save significant money if cost savings are similar to the four evaluated thus far

  12. A little here, a little there, a fairly big problem everywhere: Small-quantity-site transuranic waste disposition alternatives

    International Nuclear Information System (INIS)

    D. Luke; D. Parker; J. Moss; T. Monk; L. Fritz; B. Daugherty; K. Hladek; S. Kosiewicx

    2000-01-01

    Small quantities of transuranic (TRU) waste represent a significant challenge to the waste disposition and facility closure plans of several sites in the Department of Energy (DOE) complex. This paper presents the results of a series of evaluations, using a systems engineering approach, to identify the preferred alternative for dispositioning TRU waste from small quantity sites (SQSs). The TRU waste disposition alternatives evaluation used semi-quantitative data provided by the SQSs, potential receiving sites, and the Waste Isolation Pilot Plant (WIPP) to select and recommend candidate sites for waste receipt, interim storage, processing, and preparation for final disposition of contact-handled (CH) and remote-handled (RH) TRU waste. The evaluations of only four of these SQSs resulted in potential savings to the taxpayer of $33 million to $81 million, depending on whether mobile systems could be used to characterize, package, and certify the waste or whether each site would be required to perform this work. Small quantity shipping sites included in the evaluation included the Battelle Columbus Laboratory (BCL), University of Missouri Research Reactor (MURR), Energy Technology Engineering Center (ETEC), and Mound Laboratory. Candidate receiving sites included the Idaho National Engineering and Environmental Laboratory (INEEL), the Savannah River Site (SRS), Los Alamos National Laboratory (LANL), Oak Ridge (OR), and Hanford. At least 14 additional DOE sites having TRU waste may be able to save significant money if cost savings are similar to the four evaluated thus far

  13. Investigating the in vitro drug release kinetics from controlled release diclofenac potassium-ethocel matrix tablets and the influence of co-excipients on drug release patterns.

    Science.gov (United States)

    Shah, Shefaat Ullah; Shah, Kifayat Ullah; Rehman, Asimur; Khan, Gul Majid

    2011-04-01

    The objective of the study was to formulate and evaluate controlled release polymeric tablets of Diclofenac Potassium for the release rate, release patterns and the mechanism involved in the release process of the drug. Formulations with different types and grades of Ethyl Cellulose Ether derivatives in several drug-to-polymer ratios (D:P) were compressed into tablets using the direct compression method. In vitro drug release studies were performed in phosphate buffer (pH 7.4) as dissolution medium by using USP Method-1 (Rotating Basket Method). Similarity factor f2 and dissimilarity factor f1 were applied for checking the similarities and dissimilarities of the release profiles of different formulations. For the determination of the release mechanism and drug release kinetics various mathematical/kinetic models were employed. It was found that all of the Ethocel polymers could significantly slow down the drug release rate with Ethocel FP polymers being the most efficient, especially at D:P ratios of 10:03 which lead towards the achievement of zero or near zero order release kinetics.

  14. Light interventions: a novel approach for sustaining sleep quality and quantity of elite swimmers under conditions of shifted circadian rhythm

    DEFF Research Database (Denmark)

    Argyraki, Aikaterini; Andersen, Jakob Hildebrandt; Johansen, Lars

    2017-01-01

    , efficiency, latency, percentages of light, deep or REM sleep were the variables under investigation. The sleep output was modeled (ANOVA) with subject as a random effect and phase as fixed effect. It was observed that the light program during the intervention phase significantly enabled the conservation...... of sleep quantity and quality of the swimmers, despite the shifted circadian rhythm. The hypothesis of no effect of phase of experiment on sleep duration, efficiency, latency, percentage of light, deep and REM sleep were all accepted with p. values 0.17, 0.53, 0.90, 0.38, 0.57 and 0.52, respectively......For the 2016 Olympics at Rio De Janeiro the Danish swimmers was facing a very important problem, how to maintain a good sleep quality, quantity and high performance potential, while being subject to large shift in circadian rhythm. In the present study we suggest an alternative approach...

  15. Preparation and Characterization of Sustained Release Matrix ...

    African Journals Online (AJOL)

    tablet formulations showed a percent drug release ranging from 92.54 ± 1.02 to 98.56 ± 1.26 % at the end of 12 h. Using the spinal injury rat model, ... very common and significant problem. Nonsteroidal anti-inflammatory drugs (NSAIDs) ... animal studies, its mechanism of action involves depressing polysynaptic reflexes ...

  16. An experimental study of the trapping and release of krypton in nickel

    International Nuclear Information System (INIS)

    Donnelly, S.E.; Ingram, D.C.; Armour, D.G.

    1979-01-01

    An experimental study is reported of the trapping and release of krypton implanted into nickel at low energies ( + incident on Ni (110) the maximum quantity of gas retained in the target was found to be approximately 2.5 x 10 15 ions cm -2 . (author)

  17. Growth Hormone's Effect on Adipose Tissue: Quality versus Quantity.

    Science.gov (United States)

    Berryman, Darlene E; List, Edward O

    2017-07-26

    Obesity is an excessive accumulation or expansion of adipose tissue (AT) due to an increase in either the size and/or number of its characteristic cell type, the adipocyte. As one of the most significant public health problems of our time, obesity and its associated metabolic complications have demanded that attention be given to finding effective therapeutic options aimed at reducing adiposity or the metabolic dysfunction associated with its accumulation. Growth hormone (GH) has therapeutic potential due to its potent lipolytic effect and resultant ability to reduce AT mass while preserving lean body mass. However, AT and its resident adipocytes are significantly more dynamic and elaborate than once thought and require one not to use the reduction in absolute mass as a readout of efficacy alone. Paradoxically, therapies that reduce GH action may ultimately prove to be healthier, in part because GH also possesses potent anti-insulin activities along with concerns that GH may promote the growth of certain cancers. This review will briefly summarize some of the newer complexities of AT relevant to GH action and describe the current understanding of how GH influences this tissue using data from both humans and mice. We will conclude by considering the therapeutic use of GH or GH antagonists in obesity, as well as important gaps in knowledge regarding GH and AT.

  18. Survival with breast cancer: the importance of estrogen receptor quantity.

    Science.gov (United States)

    Shek, L L; Godolphin, W

    1989-02-01

    The survival of 1184 British Columbian women whose primary breast cancers were diagnosed and assayed for estrogen receptor (ER) between 1975 and 1981 was studied. Median follow-up was 60 months. ER concentrations yielded greater prognostic information than simple positive and negative categories. When ER data were divided into four strata: less than or equal to 1, 2-9, 10-159 and greater than or equal to 160 fmol/mg cytosol protein, the association of higher ER with prolonged survival was highly significant (P less than 0.0001) and independent of TNM stage, nodal status and menopausal status. ER less than or equal to 1 and ER = 2-9 groups were distinct with respect to overall disease-specific survival. Patient age did not predict survival when controlled for ER. Prolonged recurrence-free survival was associated with higher ER (P = 0.0001) for at least 5 years after diagnosis. This significant trend persisted after adjustments for nodal status, TNM stage, menopausal status and the type of systemic adjuvant therapy.

  19. Aerosol release factor for Pu as a consequence of an ion exchange resin fire in the process cell of a fuel reprocessing plant

    Energy Technology Data Exchange (ETDEWEB)

    Bhanti, D.P.; Malvankar, S.V.; Kotrappa, P.; Somasundaram, S.; Raghunath, B.; Curtay, A.M.

    1988-12-01

    One of the upper limit accidents usually considered in the safety analysis of a fuel reprocessing plant is an accidental explosion, followed by a fire, of an ion exchange column containing resin loaded with large quantities of plutonium. In such accidents, a certain fraction (release factor) of Pu is released in the form of an aerosol into the ventilation system, and finally to the environment through HEPA filters and the stack. The present study was undertaken to determine the aerosol release factor for Pu in the process cell of a typical fuel reprocessing plant. Geometrically similar scaled-down models of three different sizes were built, and suitably scaled-down quantities of resin loaded with thorium in nitric acid medium were burnt in these model cells. Thorium was used in place of Pu because of its physical and chemical similarities with Pu. The release factor was obtained by comparing the amount of Th in air with the total. The study also dealt with aerosol characteristics and kinematics of process of fire. The aerosol release factors for the three models were found to lie in the range 0.01-0.07%, and varied non-monotonically with model size. The analysis of scaled down results in conjunction with simplified aerosol modelling yielded the release factor for the actual cell conditions as 0.012% with an upper limit value of 0.1%. The particle size analysis based on Th-radioactivity and particle-mass indicated nonuniform tagging of Th to aerosol particles. These particles were irregularly shaped, but not as long chain-like aggregates. The study proposes, with a reasonable degree of conservatism, the release factor of 0.1% for such fires, and aerosol parameters, AMAD and sigma/sub g/, as 2 m and 2 respectively. However, for situations significantly different from the present one, the release factor of 1% recommended by the American National Standards Institute may be used with a greater degree of confidence in the light of the present work.

  20. Price effects of changing quantities supplied at the integrated european fish market

    DEFF Research Database (Denmark)

    Nielsen, Max; Smit, Jos; Guillen, Jordi

    2012-01-01

    to be −1.1. This implies that price flexibilities previously estimated for single European countries underestimate price changes at the European level caused by quantity changes. Results indicate that changing quantities can increase revenues from individual species with large own-price flexibilities...

  1. 41 CFR 101-26.507-4 - Quantities in excess of the maximum order limitation.

    Science.gov (United States)

    2010-07-01

    ... 41 Public Contracts and Property Management 2 2010-07-01 2010-07-01 true Quantities in excess of... Management Federal Property Management Regulations System FEDERAL PROPERTY MANAGEMENT REGULATIONS SUPPLY AND PROCUREMENT 26-PROCUREMENT SOURCES AND PROGRAM 26.5-GSA Procurement Programs § 101-26.507-4 Quantities in...

  2. On pure-strategy Nash equilibria in price-quantity games

    NARCIS (Netherlands)

    Bos, I.; Vermeulen, A.J.

    2015-01-01

    This paper examines the existence and characteristics of pure-strategy Nash equilibria in oligopoly models in which firms set both prices and quantities. Existence is proved for a broad and natural class of price-quantity games. With differentiated products, the equilibrium outcome is similar to

  3. 48 CFR 852.270-2 - Bread and bakery products-quantities.

    Science.gov (United States)

    2010-10-01

    ... 48 Federal Acquisition Regulations System 5 2010-10-01 2010-10-01 false Bread and bakery products... Bread and bakery products—quantities. As prescribed in 870.111-3, insert the following clause: Bread and Bakery Products—Quantities (JAN 2008) The bidder agrees to furnish up to 25 percent more or 25 percent...

  4. 29 CFR 780.814 - “Grown in commercial quantities.”

    Science.gov (United States)

    2010-07-01

    ... OF GENERAL POLICY OR INTERPRETATION NOT DIRECTLY RELATED TO REGULATIONS EXEMPTIONS APPLICABLE TO AGRICULTURE, PROCESSING OF AGRICULTURAL COMMODITIES, AND RELATED SUBJECTS UNDER THE FAIR LABOR STANDARDS ACT... “commercial” quantities, the trade understanding of what are “commercial” quantities of cotton would be...

  5. Non-Noether conserved quantity for differential equations of motion in the phase space

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    A non-Noether conserved quantity for the differential equations of motion of mechanical systems in the phase space is studied. The differential equations of motion of the systems are established and the determining equations of Lie symmetry are given. An existence theorem of non-Noether conserved quantity is obtained. An example is given to illustrate the application of the result.

  6. Are Quantity Surveyors Competent to Value for Civil Engineering Works? Evaluating QSs' Competencies and Militating Factors

    Science.gov (United States)

    Olawumi, Timothy Oluwatosin; Ayegun, Olaleke Amos

    2016-01-01

    The role of the quantity surveyor is one that is often unclear amongst the general public. This study discussed the competencies of the quantity surveyor in measuring and managing civil engineering works and also carrying out the financial management for civil engineering construction projects; also outlined the various competencies and skills…

  7. Optimal trading quantity integration as a basis for optimal portfolio management

    Directory of Open Access Journals (Sweden)

    Saša Žiković

    2005-06-01

    Full Text Available The author in this paper points out the reason behind calculating and using optimal trading quantity in conjunction with Markowitz’s Modern portfolio theory. In the opening part the author presents an example of calculating optimal weights using Markowitz’s Mean-Variance approach, followed by an explanation of basic logic behind optimal trading quantity. The use of optimal trading quantity is not limited to systems with Bernoulli outcome, but can also be used when trading shares, futures, options etc. Optimal trading quantity points out two often-overlooked axioms: (1 a system with negative mathematical expectancy can never be transformed in a system with positive mathematical expectancy, (2 by missing the optimal trading quantity an investor can turn a system with positive expectancy into a negative one. Optimal trading quantity is that quantity which maximizes geometric mean (growth function of a particular system. To determine the optimal trading quantity for simpler systems, with a very limited number of outcomes, a set of Kelly’s formulas is appropriate. In the conclusion the summary of the paper is presented.

  8. 40 CFR 355.12 - What quantities of extremely hazardous substances trigger emergency planning requirements?

    Science.gov (United States)

    2010-07-01

    ... EMERGENCY PLANNING AND NOTIFICATION Emergency Planning Who Must Comply § 355.12 What quantities of extremely... 40 Protection of Environment 27 2010-07-01 2010-07-01 false What quantities of extremely hazardous substances trigger emergency planning requirements? 355.12 Section 355.12 Protection of Environment...

  9. Variations of influence quantities in industrial irradiators and their effect on dosimetry performance

    International Nuclear Information System (INIS)

    Chu, R.D.H.

    1999-01-01

    Many environmental factors, including irradiation temperature, post-irradiation storage temperature, dose rate, relative humidity, oxygen content and the energy spectrum may affect the response of dosimetry systems used in industrial radiation processing. Although the effects of individual influence quantities have been extensively studied, the variations of these influence quantities in production irradiators and the complex relationships between the effects of different influence quantities make it difficult to assess the overall effect on the measurement uncertainty. In the development of new dosimetry systems it is important to know the effect of each influence quantity and developers of new dosimetry systems should perform studies over a wide range of irradiation conditions. Analysis parameters and manufacturing specifications should be chosen to minimize the effect of influence quantities in the environments where the dosimeters will be used. Because of possible relationships between different influence quantities, care must be taken to ensure that the response function determined in the calibration of the dosimetry system is applicable for the conditions in which the dosimeters will be used. Reference standard dosimetry systems which have been thoroughly studied and have known relationships between dose response and influence quantities should be used to verify the calibration of routine dosimetry systems under the actual conditions of use. Better understanding of the variations in influence quantities in industrial irradiators may be obtained by modeling or direct measurements and may provide improvements in the calibration of routine dosimetry system and reduction of the overall measurement uncertainty. (author)

  10. 16 CFR 500.7 - Net quantity of contents, method of expression.

    Science.gov (United States)

    2010-01-01

    ... expression. The net quantity of contents shall be expressed in terms of weight or mass, measure, numerical... consumers. The net quantity of contents statement shall be in terms of fluid measure if the commodity is liquid, or in terms of weight or mass if the commodity is solid, semi-solid, or viscous, or a mixture of...

  11. 19 CFR 151.47 - Optional entry of net quantity of petroleum or petroleum products.

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 2 2010-04-01 2010-04-01 false Optional entry of net quantity of petroleum or petroleum products. 151.47 Section 151.47 Customs Duties U.S. CUSTOMS AND BORDER PROTECTION, DEPARTMENT OF... Petroleum and Petroleum Products § 151.47 Optional entry of net quantity of petroleum or petroleum products...

  12. A small quantity of sodium arsenite will kill large cull hardwoods

    Science.gov (United States)

    Francis M. Rushmore

    1956-01-01

    Although it is well known that sodium arsenite is an effective silvicide, forestry literature contains little information about the minimum quantities of this chemical that are required to kill large cull trees. Such information would be of value because if small quantities of a chemical will produce satisfactory results, small holes or frills in the tree will hold it...

  13. Release of powdered material from waste packages

    International Nuclear Information System (INIS)

    Berg, H.P.; Gruendler, D.; Peiffer, F.; Seehars, H.D.

    1990-01-01

    Possible incidents in the operational phase of the planned German repository KONRAD for radioactive waste with negligible heat production were investigated to assess the radiological consequences. For these investigations release fractions of the radioactive materials are required. This paper deals with the determination of the release of powdered material from waste packages under mechanical stress. These determinations were based on experiments. The experimental procedure and the process parameters chosen in accordance with the conditions in the planned repository will be described. The significance of the experimental results is discussed with respect to incidents in the planned repository. 8 figs., 3 tabs

  14. Capture of Tritium Released from Cladding in the Zirconium Recycle Process

    Energy Technology Data Exchange (ETDEWEB)

    Spencer, Barry B [ORNL; Bruffey, Stephanie H [ORNL; DelCul, Guillermo Daniel [ORNL; Walker, Trenton Baird [ORNL

    2016-08-31

    Zirconium may be recovered from the Zircaloy® cladding of used nuclear fuel (UNF) for recycle or to reduce the quantities of high-level waste destined for a geologic repository. Recovery of zirconium using a chlorination process is currently under development at the Oak Ridge National Laboratory. The approach is to treat the cladding with chlorine gas to convert the zirconium in the alloy (~98 wt % of the alloy mass) to zirconium tetrachloride. A significant fraction of the tritium (0–96%) produced in nuclear fuel during irradiation may be found in zirconium-based cladding and could be released from the cladding when the solid matrix is destroyed by the chlorination reaction. To prevent uncontrolled release of radioactive tritium to other parts of the plant or to the environment, a method to recover the tritium may be required. The focus of this effort was to (1) identify potential methods for the recovery of tritium from the off-gas of the zirconium recycle process, (2) perform scoping tests on selected recovery methods using nonradioactive gas simulants, and (3) select a process design appropriate for testing on radioactive gas streams generated by the engineering-scale zirconium recycle demonstrations on radioactive used cladding.

  15. Large methane releases lead to strong aerosol forcing and reduced cloudiness

    Directory of Open Access Journals (Sweden)

    T. Kurtén

    2011-07-01

    Full Text Available The release of vast quantities of methane into the atmosphere as a result of clathrate destabilization is a potential mechanism for rapid amplification of global warming. Previous studies have calculated the enhanced warming based mainly on the radiative effect of the methane itself, with smaller contributions from the associated carbon dioxide or ozone increases. Here, we study the effect of strongly elevated methane (CH4 levels on oxidant and aerosol particle concentrations using a combination of chemistry-transport and general circulation models. A 10-fold increase in methane concentrations is predicted to significantly decrease hydroxyl radical (OH concentrations, while moderately increasing ozone (O3. These changes lead to a 70 % increase in the atmospheric lifetime of methane, and an 18 % decrease in global mean cloud droplet number concentrations (CDNC. The CDNC change causes a radiative forcing that is comparable in magnitude to the longwave radiative forcing ("enhanced greenhouse effect" of the added methane. Together, the indirect CH4-O3 and CH4-OH-aerosol forcings could more than double the warming effect of large methane increases. Our findings may help explain the anomalously large temperature changes associated with historic methane releases.

  16. Capture of Tritium Released from Cladding in the Zirconium Recycle Process

    Energy Technology Data Exchange (ETDEWEB)

    Bruffey, Stephanie H [ORNL; Spencer, Barry B [ORNL; DelCul, Guillermo Daniel [ORNL

    2016-08-31

    This report is issued as the first revision to FCRD-MRWFD-2016-000297. Zirconium may be recovered from the Zircaloy® cladding of used nuclear fuel (UNF) for recycle or to reduce the quantities of high-level waste destined for a geologic repository. Recovery of zirconium using a chlorination process is currently under development at the Oak Ridge National Laboratory. The approach is to treat the cladding with chlorine gas to convert the zirconium in the alloy (~98 wt % of the alloy mass) to zirconium tetrachloride. A significant fraction of the tritium (0–96%) produced in nuclear fuel during irradiation may be found in zirconium-based cladding and could be released from the cladding when the solid matrix is destroyed by the chlorination reaction. To prevent uncontrolled release of radioactive tritium to other parts of the plant or to the environment, a method to recover the tritium may be required. The focus of this effort was to (1) identify potential methods for the recovery of tritium from the off-gas of the zirconium recycle process, (2) perform scoping tests on selected recovery methods using non-radioactive gas simulants, and (3) select a process design appropriate for testing on radioactive gas streams generated by the engineering-scale zirconium recycle demonstrations on radioactive used cladding.

  17. Calibration of personal dosemeters in terms of the ICRU operational quantities

    International Nuclear Information System (INIS)

    McDonald, J.C.; Hertel, N.E.

    1992-01-01

    The International Commission on Radiological Units and Measurements (ICRU) has defined several new operational quantities for radiation protection purposes. The quantities to be used for personal monitoring are defined at depths in the human body. Because these quantities are impossible to measure directly, the ICRU has recommended that personal dosimeters should be calibrated under simplified conditions on an appropriate phantom, such as the ICRU sphere. The U.S. personal dosimetry accreditation programs make use of a 30 x 30 x 15 cm polymethylmethacrylate (PMMA) phantom; therefore it is necessary to relate the response of dosimeters calibrated on this phantom to the ICRU operational quantities. Calculations of the conversion factors to compute dosimeter response in terms of the operational quantities have been performed using the code MCNP. These calculations have also been compared to experimental measurements using thermoluminescent (TLD) detectors. (author)

  18. Calibration of personal dosemeters in terms of the ICRU operational quantities

    International Nuclear Information System (INIS)

    McDonald, J.C.; Hertel, N.E.

    1992-05-01

    The International Commission on Radiological Units and Measurements (ICRU) has defined several new operational quantities for radiation protection purposes. The quantities to be used for personal monitoring are defined at depths in the human body. Because these quantities are impossible to measure directly, the ICRU has recommended that personal dosemeters should be calibrated under simplified conditions on an appropriate phantom, such as the ICRU sphere. The US personal dosimetry accreditation programs make use of a 30 x 30 x 15 cm polymethymethacrylate (PMMA) phantom, therefore it is necessary to relate the response of dosemeters calibrated on this phantom to the ICRU operational quantities. Calculations of the conversion factors to compute dosemeter response in terms of the operational quantities have been performed using the code MCNP. These calculations have also been compared to experimental measurements using thermoluminescent (TLD) detectors

  19. Role of fission gas release in reactor licensing

    International Nuclear Information System (INIS)

    1975-11-01

    The release of fission gases from oxide pellets to the fuel rod internal voidage (gap) is reviewed with regard to the required safety analysis in reactor licensing. Significant analyzed effects are described, prominent gas release models are reviewed, and various methods used in the licensing process are summarized. The report thus serves as a guide to a large body of literature including company reports and government documents. A discussion of the state of the art of gas release analysis is presented

  20. Deposit Mariovo geological characteristics coal quality and quantity

    International Nuclear Information System (INIS)

    Andreevski, Borche

    2008-01-01

    Evaluation of the actual situation with energy resources, in a global scale, shows negative trends, which is result from the numerous complex factors influences. Special influence over these trends has increased requirement and consumption of the fossil fuels, driven by the intensive technological development and unplanned long-term exploitation, which causes huge reduction of the available fossil fuels deposits and significant price oscillations. Additional contribution to this tendency has the fact that potential fossil fuels reserves are controlled from limited number of owners, which allows them to have global geo-strategic control over the energy resources, world politics and other types of influences. In such conditions underdevelopment countries will feel the biggest consequences and they will be forced to provide(conditionally, if there is an energy surplus at the market) and to save considerable financial resources for satisfying their needs. Maximal usage of country's own possessed energy raw material bases the only way out from this situation and it is also used by the countries which are at he greatest development level then ours. If we want to incorporate these reserves into the energetic strategy and energy balances they must be exactly defined and determined. According to the presented approach, paper has aim to make synthesis of previous investigations, through argumentation of geological specifics and quantitative-qualitative characteristics of deposit Mariovo coal given in the available documentation, and also has intention to point out its respectable characteristics. (Author)

  1. Deposit Mariovo geological characteristics coal quality and quantity

    International Nuclear Information System (INIS)

    Andreevski, Borche

    2007-01-01

    Evaluation of the actual situation with energy resources, in a global scale, shows negative trends, which is result from the numerous complex factors influences. Special influence over these trends has increased requirement and consumption of the fossil fuels, driven by the intensive technological development and unplanned long-term exploitation, which causes huge reduction of the available fossil fuels deposits and significant price oscillations. Additional contribution to this tendency has the fact that potential fossil fuels reserves are controlled from limited number of owners, which allows them to have global geo-strategic control over the energy resources, world politics and other types of influences. In such conditions underdevelopment countries will feel the biggest consequences and they will be forced to provide(conditionally, if there is an energy surplus at the market) and to save considerable financial resources for satisfying their needs. Maximal usage of country's own possessed energy raw material bases the only way out from this situation and it is also used by the countries which are at he greatest development level then ours. If we want to incorporate these reserves into the energetic strategy and energy balances they must be exactly defined and determined. According to the presented approach, paper has aim to make synthesis of previous investigations, through argumentation of geological specifics and quantitative-qualitative characteristics of deposit Mariovo coal given in the available documentation, and also has intention to point out its respectable characteristics. (Author)

  2. Operational experience in mitigating flammable gas releases from Hanford Site Tank 241-SY-101

    International Nuclear Information System (INIS)

    Lentsch, J.W.; Babad, H.; Kirch, N.W.

    1995-01-01

    Flammable gases consisting of hydrogen, nitrous oxide, ammonia, and methane are periodically released from Hanford Site waste tank 241-SY-101 at concentrations above the flammable limit. A large mixer pump installed in the tank in 1993 has effectively mitigated this problem by continuously releasing small amounts of the flammable gases at the rate they are generated. Tank 241-SY-101 is also equipped with multiple high-sensitivity gas monitoring systems and level detection systems to measure the quantity of gas that is retained in and released from the waste

  3. Environmental Release Prevention and Control Plan

    International Nuclear Information System (INIS)

    Mamatey, A.; Arnett, M.

    1997-01-01

    During the history of SRS, continual improvements in facilities, process, and operations, and changes in the site''s mission have reduced the amount of radioactive liquid releases. In the early years of SRS (1958 to 1965), the amount of tritium discharged to the Savannah River averaged approximately 61,000 curies a year. During the mid-1980''s (1983 to 1988), liquid releases of tritium averaged 27,000 curies a year. By 1996, liquid releases of tritium are projected to be just 3000 curies for the year. This large projected decrease is the result of the planned shut-down of all reactors and the anticipated significant decline in the amount of tritium migrating from the site seepage basins and the Solid Waste Disposal Facility

  4. Gravitational vacuum and energy release in microworld

    International Nuclear Information System (INIS)

    Mel'nikov, V.N.; Nikolaev, Yu.M.; Stanyukovich, K.P.

    1981-01-01

    It is shown that gravitati.onal interaction can be connected with the processes of energy release in microworld. Suggested is a planckeon model within the frames of which gradual production of the observed substance of the Universe during the whole evolution is explained. Burst processes in nuclei of the Galaxy are explained. It is concluded that the theory of gravitational vacuum creates preconditions for developing the general theory of the field explaining the basic peculiarities of the micro- and macroworld, reveals significant applications in the physics of elementary particles and atomic nucleus. The process of 235 U fission is considered for testing the hypothesis that the coefficient of energy release depends on the nature of the reaction in different processes of energy release in the micro- and macroworld [ru

  5. The observation of leptin levels in pregnant women newborn and newborn's weight and its clinical significance

    International Nuclear Information System (INIS)

    Yuan Gengbiao; Xiao Jin; Shi Xin; Chen Xuehong

    2002-01-01

    To study the relationship of leptin quantity of placenta, amniotic fluid, umbilical blood, maternal blood and newborn's weight, leptin levels of placenta, amniotic fluid, umbilical blood and maternal blood of 59 pregnant women were detected by RIA. Results were: (1) leptin was be detected from placenta, amniotic fluid, umbilical blood and maternal blood; (2) there was an obvious difference between leptin quantities of placenta, amniotic fluid, umbilical blood and maternal blood (P < 0.01); (3) there was an obvious difference between leptin quantities of placenta, amniotic fluid, umbilical blood and maternal blood for normal pregnant women and pregnancy induced hypertension (P < 0.01); (4) there was an obvious difference between leptin quantities of maternal blood and placenta (P < 0.01). It may be of important significance to detect eh leptin quantity of amniotic fluid and maternal blood in pregnant women for predicting the weight and growth of newborns and treat pregnancy induced hypertension

  6. Investigation of selection methods im mutation breeding of barley for protein quantity and quality

    International Nuclear Information System (INIS)

    Ulonska, E.; Gaul, H.; Baumer, M.; Gesellschaft fuer Strahlen- und Umweltforschung m.b.H., Gruenbach

    1975-01-01

    This mutation breeding programme is investigating the qualification of micro-mutations for the selection of improved protein quality and quantity. Normally, improvement of protein content in micro-mutations is rather small. Therefore, it is important to develop methods and conditions of selection being (a) capable of measuring these small deviations in protein content and quality, and (b) simple to use. In two experiments carried out in 1971 and 1972 nitrogen fertilization was found to be the most important factor in the improvement of selection conditions. There is a highly significant negative correlation between crude protein content and the standard deviation; i.e. the higher the content of crude protein, the lower the variation coefficient. This in turn leads to an increase of genetic variation necessary for better selection progress. Nitrogen fertilization, especially during ear emergence, covers environmental influences - e.g., planting space, sowing rate, growing in different plots (6, 3, 2, 1 rows or in half-ear hills) - to a great extent. Thus, by applying high doses of nitrogen dressings comparable results can be achieved. In an overall selection experiment (testing the entire crossing and mutation material available at Weihenstephan in a stepwise selection from 1971 to 1973) and two selection experiments conducted in 1971 to 1973 with micro-mutants - variety Nota, 4 times X-rayed and the naked barley strain 1606 treated once with EMS - significant selection results were found. (author)

  7. Effect of masticatory stimulation on the quantity and quality of saliva and the salivary metabolomic profile.

    Directory of Open Access Journals (Sweden)

    Nobuyuki Okuma

    Full Text Available This study characterized the changes in quality and quantity of saliva, and changes in the salivary metabolomic profile, to understand the effects of masticatory stimulation.Stimulated and unstimulated saliva samples were collected from 55 subjects and salivary hydrophilic metabolites were comprehensively quantified using capillary electrophoresis-time-of-flight mass spectrometry.In total, 137 metabolites were identified and quantified. The concentrations of 44 metabolites in stimulated saliva were significantly higher than those in unstimulated saliva. Pathway analysis identified the upregulation of the urea cycle and synthesis and degradation pathways of glycine, serine, cysteine and threonine in stimulated saliva. A principal component analysis revealed that the effect of masticatory stimulation on salivary metabolomic profiles was less dependent on sample population sex, age, and smoking. The concentrations of only 1 metabolite in unstimulated saliva, and of 3 metabolites stimulated saliva, showed significant correlation with salivary secretion volume, indicating that the salivary metabolomic profile and salivary secretion volume were independent factors.Masticatory stimulation affected not only salivary secretion volume, but also metabolite concentration patterns. A low correlation between the secretion volume and these patterns supports the conclusion that the salivary metabolomic profile may be a new indicator to characterize masticatory stimulation.

  8. Do human parents face a quantity-quality tradeoff?: evidence from a Shuar community.

    Science.gov (United States)

    Hagen, Edward H; Barrett, H Clark; Price, Michael E

    2006-07-01

    A number of evolutionary theories of human life history assume a quantity-quality tradeoff for offspring production: parents with fewer offspring can have higher biological fitness than those with more. Direct evidence for such a tradeoff, however, is mixed. We tested this assumption in a community of Ecuadorian Shuar hunter-horticulturalists, using child anthropometry as a proxy for fitness. We measured the impact of household consumer/producer (CP) ratio on height, weight, skinfold thicknesses, and arm and calf circumferences of 85 children and young adults. To control for possible "phenotypic" correlates that might mask the effect of CP ratio on anthropometry, we also measured household garden productivity, wealth, and social status. Regression models of the age-standardized variables indicated a significant negative impact of CP ratio on child growth and nutrition. The age-standardized height and weight of children in households with the largest CP ratio (10) were 1.38 and 1.44 standard deviations, respectively, below those of children in households with the smallest CP ratio (2). Surprisingly, garden productivity, wealth, and status had little to no effect on the fitness proxies. There was, however, an interesting and unexpected interaction between status and sex: for females, but not males, higher father status correlated significantly with higher values on the proxies.

  9. Uncertainties in the measured quantities of water leaving waste Tank 241-C-106 via the ventilation system

    Energy Technology Data Exchange (ETDEWEB)

    Minteer, D.J.

    1995-01-23

    The purpose of this analysis is to estimate the uncertainty in the measured quantity of water which typically leaves Tank 241-C-106 via the ventilation system each month. Such measurements are essential for heat removal estimation and tank liquid level verification purposes. The uncertainty associated with the current, infrequent, manual method of measurement (involves various psychrometric and pressure measurements) is suspected to be unreasonably high. Thus, the possible reduction of this uncertainty using a continuous, automated method of measurement will also be estimated. There are three major conclusions as a result of this analysis: (1) the uncertainties associated with the current (infrequent, manual) method of measuring the water which typically leaves Tank 241-C-106 per month via the ventilation system are indeed quite high (80% to 120%); (2) given the current psychrometric and pressure measurement methods and any tank which loses considerable moisture through active ventilation, such as Tank 241-C-106, significant quantities of liquid can actually leak from the tank before a leak can be positively identified via liquid level measurement; (3) using improved (continuous, automated) methods of taking the psychrometric and pressure measurements, the uncertainty in the measured quantity of water leaving Tank 241-C-106 via the ventilation system can be reduced by approximately an order of magnitude.

  10. Uncertainties in the measured quantities of water leaving waste Tank 241-C-106 via the ventilation system

    International Nuclear Information System (INIS)

    Minteer, D.J.

    1995-01-01

    The purpose of this analysis is to estimate the uncertainty in the measured quantity of water which typically leaves Tank 241-C-106 via the ventilation system each month. Such measurements are essential for heat removal estimation and tank liquid level verification purposes. The uncertainty associated with the current, infrequent, manual method of measurement (involves various psychrometric and pressure measurements) is suspected to be unreasonably high. Thus, the possible reduction of this uncertainty using a continuous, automated method of measurement will also be estimated. There are three major conclusions as a result of this analysis: (1) the uncertainties associated with the current (infrequent, manual) method of measuring the water which typically leaves Tank 241-C-106 per month via the ventilation system are indeed quite high (80% to 120%); (2) given the current psychrometric and pressure measurement methods and any tank which loses considerable moisture through active ventilation, such as Tank 241-C-106, significant quantities of liquid can actually leak from the tank before a leak can be positively identified via liquid level measurement; (3) using improved (continuous, automated) methods of taking the psychrometric and pressure measurements, the uncertainty in the measured quantity of water leaving Tank 241-C-106 via the ventilation system can be reduced by approximately an order of magnitude

  11. Effects of hyperthyroidism and hypothyroidism on rat growth hormone release induced by thyrotropin-releasing hormone.

    Science.gov (United States)

    Chihara, K; Kato, Y; Ohgo, S; Iwasaki, Y; Maeda, K

    1976-06-01

    The effect of synthetic thyrotropin-releasing hormone (TRH) on the release of growth hormone (GH) and thyroid-stimulating hormone (TSH) was investigated in euthyroid, hypothyroid, and hyperthyroid rats under urethane anesthesia. In euthyroid control rats, intravenous injection of TRH (200 ng/100 g BW) resulted in a significant increase in both plasma GH and TSH. In rats made hypothyroid by treatment with propylthiouracil or by thyroidectomy, basal GH and TSH levels were significantly elevated with exaggerated responses to TRH. In contrast, plasma GH and TSH responses to TRH were both significantly inhibited in rats made hyperthyroid by L-thyroxine (T4) treatment. These results suggest that altered thyroid status influences GH release as well as TSH secretion induced by TRH in rats.

  12. The gas release programs to increase competition in the European gas market

    International Nuclear Information System (INIS)

    Clastres, Cedric

    2005-01-01

    Regulators have implemented asymmetric regulation measures, such as gas release programs and market share targets, because of European gas supply features and gas market specificities. Empirical experiences show in line with economic theory that these regulation measures favour entry and competition without deterring investments. If we look at impacts on competition, they are mitigated. Some positive effects result from the increase in consumption or in importation and transportation infrastructure developments. But these regulations can also encourage anti-competitive behaviours like collusion, cream-skimming, reverse cherry picking or inefficient entries. Gas release measures establish a link between the incumbent and its competitors. A system of constraints on operators capacities can also appear. Thus, pricing or quantity strategies are more complex. Equilibrium prices are more volatile and very different of competition mark-up. The incumbent, for high gas release quantities and low supplies, can increase its costs to make more profit. This Raising Rivals' Costs strategy often occur if the gas release price is closer to supply costs. This strategy does not impact on consumers surplus but decreases welfare. The regulator can restore incentives to efficiency by setting gas release proportion function of incumbent's supplies. This proportion must be high enough to have a positive impact on the market because of incumbent's incentives to efficiency and greater total quantities sold by the two operators. But, on another way, it must not be too high as it could, thus, increase the probability of Raising Rivals' Costs or favour collusive strategies. (author) [fr

  13. Released radioactivity reducing facility

    International Nuclear Information System (INIS)

    Tanaka, Takeaki.

    1992-01-01

    Upon occurrence of a reactor accident, penetration portions of a reactor container, as a main leakage source from a reactor container, are surrounded by a plurality of gas-tight chambers, the outside of which is surrounded by highly gas-tightly buildings. Branched pipelines of an emergency gas processing system are introduced to each of the gas-tight chambers and they are joined and in communication with an emergency gas processing device. With such a constitution, radioactive materials are prevented from leaking directly from the buildings. Further, pipeline openings of the emergency gas processing facility are disposed in the plurality highly gas-tight penetration chambers. If the radioactive materials are leaked from the reactor to elevate the pressure in the penetration chambers, the radioactive materials are introduced to a filter device in the emergency gas processing facility by way of the branched pipelines, filtered and then released to the atmosphere. Accordingly, the reliability and safety of the system can be improved. (T.M.)

  14. Containment and release management

    International Nuclear Information System (INIS)

    Lehner, J.R.; Pratt, W.T.

    1988-01-01

    Reducing the risk from potentially severe accidents by appropriate accident management strategies is receiving increased attention from the international reactor safety community. Considerable uncertainty still surrounds some of the physical phenomena likely to occur during a severe accident. The USNRC, in developing its research plan for accident management, wants to ensure that both the developers and implementers of accident management strategies are aware of the uncertainty associated with the plant operators' ability to correctly diagnose an accident, as well as the uncertainties associated with various preventive and mitigative strategies. The use of a particular accident management strategy can have both positive and negative effects on the status of a plant and these effects must be carefully weighed before a particular course of action is chosen and implemented. By using examples of severe accident scenarios, initial insights are presented here regarding the indications plant operators may have to alert them to particular accident states. Insights are also offered on the various management actions operators and plant technical staff might pursue for particular accident situations and the pros and cons associated with such actions. The examples given are taken for the most part from the containment and release phase of accident management, since this is the current focus of the effort in the accident management area at Brookhaven National Laboratory. 2 refs

  15. Released radioactivity reducing device

    International Nuclear Information System (INIS)

    Miyamoto, Yumi.

    1995-01-01

    A water scrubber is disposed in a scrubber tank and a stainless steel fiber filter is disposed above the water scrubber. The upper end of the scrubber tank is connected by way of a second bent tube to a capturing vessel incorporating a moisture removing layer and an activated carbon filter. The exit of the capturing vessel is connected to a stack. Upon occurrence of an accident of a BWR-type power plant, gases containing radioactive materials released from a reactor container are discharged into the water scrubber from a first bent tube through a venturi tube nozzle, and water soluble and aerosol-like radioactive materials are captured in the water. Aerosol and splashes of water droplets which can not be captured thoroughly by the water scrubber are captured by the stainless steel fiber filter. Gases passing through the scrubber tank are introduced to a capturing vessel through a second bent tube, and organic iodine is captured by the activated carbon filter. (I.N.)

  16. COMMERCIAL SNF ACCIDENT RELEASE FRACTIONS

    Energy Technology Data Exchange (ETDEWEB)

    S.O. Bader

    1999-10-18

    The purpose of this design analysis is to specify and document the total and respirable fractions for radioactive materials that are released from an accident event at the Monitored Geologic Repository (MGR) involving commercial spent nuclear fuel (CSNF) in a dry environment. The total and respirable release fractions will be used to support the preclosure licensing basis for the MGR. The total release fraction is defined as the fraction of total CSNF assembly inventory, typically expressed as an activity inventory (e.g., curies), of a given radionuclide that is released to the environment from a waste form. The radionuclides are released from the inside of breached fuel rods (or pins) and from the detachment of radioactive material (crud) from the outside surfaces of fuel rods and other components of fuel assemblies. The total release fraction accounts for several mechanisms that tend to retain, retard, or diminish the amount of radionuclides that are available for transport to dose receptors or otherwise can be shown to reduce exposure of receptors to radiological releases. The total release fraction includes a fraction of airborne material that is respirable and could result in inhalation doses. This subset of the total release fraction is referred to as the respirable release fraction. Potential accidents may involve waste forms that are characterized as either bare (unconfined) fuel assemblies or confined fuel assemblies. The confined CSNF assemblies at the MGR are contained in shipping casks, canisters, or disposal containers (waste packages). In contrast to the bare fuel assemblies, the container that confines the fuel assemblies has the potential of providing an additional barrier for diminishing the total release fraction should the fuel rod cladding breach during an accident. However, this analysis will not take credit for this additional bamer and will establish only the total release fractions for bare unconfined CSNF assemblies, which may however be

  17. COMMERCIAL SNF ACCIDENT RELEASE FRACTIONS

    International Nuclear Information System (INIS)

    S.O. Bader

    1999-01-01

    The purpose of this design analysis is to specify and document the total and respirable fractions for radioactive materials that are released from an accident event at the Monitored Geologic Repository (MGR) involving commercial spent nuclear fuel (CSNF) in a dry environment. The total and respirable release fractions will be used to support the preclosure licensing basis for the MGR. The total release fraction is defined as the fraction of total CSNF assembly inventory, typically expressed as an activity inventory (e.g., curies), of a given radionuclide that is released to the environment from a waste form. The radionuclides are released from the inside of breached fuel rods (or pins) and from the detachment of radioactive material (crud) from the outside surfaces of fuel rods and other components of fuel assemblies. The total release fraction accounts for several mechanisms that tend to retain, retard, or diminish the amount of radionuclides that are available for transport to dose receptors or otherwise can be shown to reduce exposure of receptors to radiological releases. The total release fraction includes a fraction of airborne material that is respirable and could result in inhalation doses. This subset of the total release fraction is referred to as the respirable release fraction. Potential accidents may involve waste forms that are characterized as either bare (unconfined) fuel assemblies or confined fuel assemblies. The confined CSNF assemblies at the MGR are contained in shipping casks, canisters, or disposal containers (waste packages). In contrast to the bare fuel assemblies, the container that confines the fuel assemblies has the potential of providing an additional barrier for diminishing the total release fraction should the fuel rod cladding breach during an accident. However, this analysis will not take credit for this additional bamer and will establish only the total release fractions for bare unconfined CSNF assemblies, which may however be

  18. Underground water stress release models

    Science.gov (United States)

    Li, Yong; Dang, Shenjun; Lü, Shaochuan

    2011-08-01

    The accumulation of tectonic stress may cause earthquakes at some epochs. However, in most cases, it leads to crustal deformations. Underground water level is a sensitive indication of the crustal deformations. We incorporate the information of the underground water level into the stress release models (SRM), and obtain the underground water stress release model (USRM). We apply USRM to the earthquakes occurred at Tangshan region. The analysis shows that the underground water stress release model outperforms both Poisson model and stress release model. Monte Carlo simulation shows that the simulated seismicity by USRM is very close to the real seismicity.

  19. Effect of maca supplementation on bovine sperm quantity and quality followed over two spermatogenic cycles.

    Science.gov (United States)

    Clément, C; Kneubühler, J; Urwyler, A; Witschi, U; Kreuzer, M

    2010-07-15

    Maca (Lepidium meyenii Walpers), is an Andean crop that grows between 3,800 and 4,500 m a.s.l. The persistent interest in this plant is based on its assumed effects on fertility of male mammals due to the prevalence of certain, partially specific, secondary compounds. The present study aimed at evaluating the effect of maca supplementation on quality and quantity of semen, mating behavior, and clinical status of peripubertal breeding bulls. The experiment followed a cross-over design lasting for 23 wk with 3 wk of adaptation and baseline measurements, and 2 x 10 wk of treatment feeding thus covering two times the complete 8-wk spermatogenic cycle. Seventy-eight 55 wk to 84 wk old breeding bulls received either no maca (control) or maca (233 mg dried hypocotyls/kg body weight/day) for 10 wk followed by 10 wk without maca (maca early) or maca only in the last 10 wk (maca late). Measurements were always made in the last 2 wk of each period. Apart from standard analyses, ejaculates were analyzed by flow cytometry. Data was evaluated by analysis of variance considering the repeated measurement structure of the data. Significant treatment by measurement period indicated direct or carry-over effects of maca. Maca supplementation had no direct effect on body weight, testes circumference, rectal temperature, mating behavior, and ejaculate volume. However, supplementing maca in the first 10 wk period increased the number of sperms in the second 10 wk period, i.e., when the animals no longer received maca. The DNA fragmentation index and the visually assessed motility of the sperms of bulls, that initially showed a borderline sperm quality, were significantly improved with early maca supplementation, while no such effect was observed in the two other groups. No effects occurred in the proportion of intact sperm plasma membranes or acrosomes or both. In conclusion, maca supplementation seems to improve sperm quantity and quality of bulls to a certain degree, while mating

  20. Release of low-contaminated reactor wastes for unrestricted use

    International Nuclear Information System (INIS)

    Carleson, G.

    1982-01-01

    A generic methodology has been used to evaluate the dose contributions to an individual and to the population of five categories of low-contaminated reactor wastes produced according to the Swedish program and released for unrestricted handling and use. A reference quantity with a surface dose rate below a predetermined level is followed along the whole commercial pathway from the reactor station to the final product consumer and/or a municipal waste station. Dose contributions are calculated for each step in a normal pathway under maximally unfavourable conditions. (Auth.)

  1. Spatial and temporal patterns of dissolved organic matter quantity and quality in the Mississippi River Basin, 1997–2013

    Science.gov (United States)

    Stackpoole, Sarah M.; Stets, Edward G.; Clow, David W.; Burns, Douglas A.; Aiken, George R.; Aulenbach, Brent T.; Creed, Irena F.; Hirsch, Robert M.; Laudon, Hjalmar; Pellerin, Brian; Striegl, Robert G.

    2017-01-01

    Recent studies have found insignificant or decreasing trends in time-series dissolved organic carbon (DOC) datasets, questioning the assumption that long-term DOC concentrations in surface waters are increasing in response to anthropogenic forcing, including climate change, land use, and atmospheric acid deposition. We used the weighted regressions on time, discharge, and season (WRTDS) model to estimate annual flow-normalized concentrations and fluxes to determine if changes in DOC quantity and quality signal anthropogenic forcing at 10 locations in the Mississippi River Basin. Despite increases in agriculture and urban development throughout the basin, net increases in DOC concentration and flux were significant at only 3 of 10 sites from 1997 to 2013 and ranged between −3.5% to +18% and −0.1 to 19%, respectively. Positive shifts in DOC quality, characterized by increasing specific ultraviolet absorbance at 254 nm, ranged between +8% and +45%, but only occurred at one of the sites with significant DOC quantity increases. Basinwide reductions in atmospheric sulfate deposition did not result in large increases in DOC either, likely because of the high buffering capacity of the soil. Hydroclimatic factors including annual discharge, precipitation, and temperature did not significantly change during the 17-year timespan of this study, which contrasts with results from previous studies showing significant increases in precipitation and discharge over a century time scale. Our study also contrasts with those from smaller catchments, which have shown stronger DOC responses to climate, land use, and acidic deposition. This temporal and spatial analysis indicated that there was a potential change in DOC sources in the Mississippi River Basin between 1997 and 2013. However, the overall magnitude of DOC trends was not large, and the pattern in quantity and quality increases for the 10 study sites was not consistent throughout the basin.

  2. Quantity and quality limit detritivore growth: mechanisms revealed by ecological stoichiometry and co-limitation theory.

    Science.gov (United States)

    Halvorson, Halvor M; Sperfeld, Erik; Evans-White, Michelle A

    2017-12-01

    Resource quantity and quality are fundamental bottom-up constraints on consumers. Best understood in autotroph-based systems, co-occurrence of these constraints may be common but remains poorly studied in detrital-based systems. Here, we used a laboratory growth experiment to test limitation of the detritivorous caddisfly larvae Pycnopsyche lepida across a concurrent gradient of oak litter quantity (food supply) and quality (phosphorus : carbon [P:C ratios]). Growth increased simultaneously with quantity and quality, indicating co-limitation across the resource gradients. We merged approaches of ecological stoichiometry and co-limitation theory, showing how co-limitation reflected shifts in C and P acquisition throughout homeostatic regulation. Increased growth was best explained by elevated consumption rates and improved P assimilation, which both increased with elevated quantity and quality. Notably, C assimilation efficiencies remained unchanged and achieved maximum 18% at low quantity despite pronounced C limitation. Detrital C recalcitrance and substantive post-assimilatory C losses probably set a minimum quantity threshold to achieve positive C balance. Above this threshold, greater quality enhanced larval growth probably by improving P assimilation toward P-intensive growth. We suggest this interplay of C and P acquisition contributes to detritivore co-limitation, highlighting quantity and quality as potential simultaneous bottom-up controls in detrital-based ecosystems, including under anthropogenic change like nutrient enrichment. © 2017 by the Ecological Society of America.

  3. Effects of Fuel Quantity on Soot Formation Process for Biomass-Based Renewable Diesel Fuel Combustion

    KAUST Repository

    Jing, Wei

    2016-12-01

    Soot formation process was investigated for biomass-based renewable diesel fuel, such as biomass to liquid (BTL), and conventional diesel combustion under varied fuel quantities injected into a constant volume combustion chamber. Soot measurement was implemented by two-color pyrometry under quiescent type diesel engine conditions (1000 K and 21% O2 concentration). Different fuel quantities, which correspond to different injection widths from 0.5 ms to 2 ms under constant injection pressure (1000 bar), were used to simulate different loads in engines. For a given fuel, soot temperature and KL factor show a different trend at initial stage for different fuel quantities, where a higher soot temperature can be found in a small fuel quantity case but a higher KL factor is observed in a large fuel quantity case generally. Another difference occurs at the end of combustion due to the termination of fuel injection. Additionally, BTL flame has a lower soot temperature, especially under a larger fuel quantity (2 ms injection width). Meanwhile, average soot level is lower for BTL flame, especially under a lower fuel quantity (0.5 ms injection width). BTL shows an overall low sooting behavior with low soot temperature compared to diesel, however, trade-off between soot level and soot temperature needs to be carefully selected when different loads are used.

  4. Flash release an alternative for releasing complex MEMS devices

    NARCIS (Netherlands)

    Deladi, S.; Krijnen, Gijsbertus J.M.; Elwenspoek, Michael Curt

    2004-01-01

    A novel time-saving and cost-effective release technique has been developed and is described. The physical nature of the process is explained in combination with experimental observations. The results of the flash release process are compared with those of freeze-drying and supercritical CO2

  5. Minimizing lead release levels in secondary smelters slags

    International Nuclear Information System (INIS)

    Shenkler, E.S.; Graham, S.; Ghosh, R.; Greenhut, V.A.

    1991-01-01

    Five lead-containing slags and four mattes were analyzed to reveal microstructure, semi-quantitative microchemistry, and phases present. To determine if the slags could be incorporated as a glass so that lead release levels could be stabilized, glass batches were formulated based on slag compositions. Leaching tests showed that all materials that were fritted in a glass batch had lower lead release levels than non-adjusted materials, and all could satisfy EPA test requirements. The mole ratio of glass modifiers to glass formers played an important role in the extent of lead release. Small additions of phosphate to a batch had a significant effect on lowering lead release levels

  6. The influence of granulating solvents on drug release from tablets ...

    African Journals Online (AJOL)

    ... significantly lower than the other wet granulated tablets, but higher than the matrix tablets. The granulating solvent influenced the release of drug which increased with increase in the water content. Key Words: Grewia gum: Granulating solvents; Release mechanisms. Journal of Pharmacy and Bioresources Vol.1(1) 2004: ...

  7. Growth hormone (GH)-releasing activity of chicken GH-releasing hormone (GHRH) in chickens.

    Science.gov (United States)

    Harvey, S; Gineste, C; Gaylinn, B D

    2014-08-01

    Two peptides with sequence similarities to growth hormone releasing hormone (GHRH) have been identified by analysis of the chicken genome. One of these peptides, chicken (c) GHRH-LP (like peptide) was previously found to poorly bind to chicken pituitary membranes or to cloned and expressed chicken GHRH receptors and had little, if any, growth hormone (GH)-releasing activity in vivo or in vitro. In contrast, a second more recently discovered peptide, cGHRH, does bind to cloned and expressed cGHRH receptors and increases cAMP activity in transfected cells. The possibility that this peptide may have in vivo GH-releasing activity was therefore assessed. The intravenous (i.v.) administration of cGHRH to immature chickens, at doses of 3-100 μg/kg, significantly increased circulating GH concentrations within 10 min of injection and the plasma GH levels remained elevated for at least 30 min after the injection of maximally effective doses. The plasma GH responses to cGHRH were comparable with those induced by human (h) or porcine (p) GHRH preparations and to that induced by thyrotropin releasing hormone (TRH). In marked contrast, the i.v. injection of cGHRH-LP had no significant effect on circulating GH concentrations in immature chicks. GH release was also increased from slaughterhouse chicken pituitary glands perifused for 5 min with cGHRH at doses of 0.1 μg/ml or 1.0 μg/ml, comparable with GH responses to hGHRH1-44. In contrast, the perifusion of chicken pituitary glands with cGHRH-LP had no significant effect on GH release. In summary, these results demonstrate that cGHRH has GH-releasing activity in chickens and support the possibility that it is the endogenous ligand of the cGHRH receptor. Copyright © 2014 Elsevier Inc. All rights reserved.

  8. Non-Noether Conserved Quantity for Relativistic Nonholonomic System with Variable Mass

    International Nuclear Information System (INIS)

    Qiao Yongfen; Li Renjie; Ma Yongsheng

    2005-01-01

    Using form invariance under special infinitesimal transformations in which time is not variable, the non-Noether conserved quantity of the relativistic nonholonomic system with variable mass is studied. The differential equations of motion of the system are established. The definition and criterion of the form invariance of the system under infinitesimal transformations are studied. The necessary and sufficient condition under which the form invariance is a Lie symmetry is given. The condition under which the form invariance can be led to a non-Noether conserved quantity and the form of the conserved quantity are obtained. Finally, an example is given to illustrate the application of the result.

  9. The estimation of differential counting measurements of possitive quantities with relatively large statistical errors

    International Nuclear Information System (INIS)

    Vincent, C.H.

    1982-01-01

    Bayes' principle is applied to the differential counting measurement of a positive quantity in which the statistical errors are not necessarily small in relation to the true value of the quantity. The methods of estimation derived are found to give consistent results and to avoid the anomalous negative estimates sometimes obtained by conventional methods. One of the methods given provides a simple means of deriving the required estimates from conventionally presented results and appears to have wide potential applications. Both methods provide the actual posterior probability distribution of the quantity to be measured. A particularly important potential application is the correction of counts on low radioacitvity samples for background. (orig.)

  10. Coordinated Lot-sizing and Dynamic Prizing under a Supplier All-units Quantity Discount

    Directory of Open Access Journals (Sweden)

    Sandra Transchel

    2008-05-01

    Full Text Available We consider an economic order quantity model where the supplier offers an all-units quantity discount and a price sensitive customer demand. We compare a decentralized decision framework where selling price and replenishment policy are determined independently to simultaneous decision making. Constant and dynamic pricing are distinguished. We derive structural properties and develop algorithms that determine the optimal pricing and replenishment policy and show how quantity discounts not only influence the purchasing strategy but also the pricing policy. A sensitivity analysis indicates the impact of the fixed-holding cost ratio, the discount policy, and the customers' price sensitivity on the optimal decisions.

  11. Validity of the concept of absorbed dose as a physical quantity

    International Nuclear Information System (INIS)

    Tada, Jun-Ichiro; Katoh, Kazuaki.

    1995-01-01

    The concept of the 'absorbed dose' of ionizing radiation is scrutinized from physical point of view. It is shown that the concept and definition of the quantity in the ICRU system is disqualified as a physical quantity and the absorbed dose can not always be a 'measure of cause' in describing causality relation between radiation and effects on matter. The current absorbed dose depends even on the energy that have already been brought out from the matter, contrary to the intention of introducing the quantity. Trials to remove these difficulties are made. However, it is also shown there still exists an essential problem that cannot be solved by improving the formulation. (author)

  12. QUANTITY DISCOUNTS IN SUPPLIER SELECTION PROBLEM BY USE OF FUZZY MULTI-CRITERIA PROGRAMMING

    Directory of Open Access Journals (Sweden)

    Tunjo Perić

    2011-02-01

    Full Text Available Supplier selection in supply chain is a multi-criteria problem that involves a number of quantitative and qualitative factors. This paper deals with a concrete problem of flour purchase by a company that manufactures bakery products and the purchasing price of flour depends on the quantity ordered. The criteria for supplier selection and quantities supplied by individual suppliers are: purchase costs, product quality and reliability of suppliers. The problem is solved using a model that combines revised weighting method and fuzzy multi-criteria linear programming (FMCLP. The paper highlights the efficiency of the proposed methodology in conditions when purchasing prices depend on order quantities.

  13. Comparison of the accident process, radioactivity release and ground contamination between Chernobyl and Fukushima-1

    International Nuclear Information System (INIS)

    Imanaka, Tetsuji; Hayashi, Gohei; Endo, Satoru

    2015-01-01

    In this report, we have reviewed the basic features of the accident processes and radioactivity releases that occurred in the Chernobyl accident (1986) and in the Fukushima-1 accident (2011). The Chernobyl accident was a power-surge accident that was caused by a failure of control of a fission chain reaction, which instantaneously destroyed the reactor and building, whereas the Fukushima-1 accident was a loss-of-coolant accident in which the reactor cores of three units were melted by decay heat after losing the electricity supply. Although the quantity of radioactive noble gases released from Fukushima-1 exceeded the amount released from Chernobyl, the size of land area severely contaminated by 137 Cesium ( 137 Cs) was 10 times smaller around Fukushima-1 compared with around Chernobyl. The differences in the accident process are reflected in the composition of the discharged radioactivity as well as in the composition of the ground contamination. Volatile radionuclides (such as 132 Te- 132 I, 131 I, 134 Cs and 137 Cs) contributed to the gamma-ray exposure from the ground contamination around Fukishima-1, whereas a greater variety of radionuclides contributed significantly around Chernobyl. When radioactivity deposition occurred, the radiation exposure rate near Chernobyl is estimated to have been 770 μGy h −1 per initial 137 Cs deposition of 1000 kBq m −2 , whereas it was 100 μGy h −1 around Fukushima-1. Estimates of the cumulative exposure for 30 years are 970 and 570 mGy per initial deposition of 1000 kBq m −2 for Chernobyl and Fukusima-1, respectively. Of these exposures, 49 and 98% were contributed by radiocesiums ( 134 Cs + 137 Cs) around Chernobyl and Fukushima-1, respectively

  14. Biomass decomposition and nutrient release from black oat and hairy vetch residues deposited in a vineyard

    Directory of Open Access Journals (Sweden)

    Paulo Ademar Avelar Ferreira

    2014-10-01

    Full Text Available A significant quantity of nutrients in vineyards may return to the soil each year through decomposition of residues from cover plants. This study aimed to evaluate biomass decomposition and nutrient release from residues of black oats and hairy vetch deposited in the vines rows, with and without plastic shelter, and in the between-row areas throughout the vegetative and productive cycle of the plants. The study was conducted in a commercial vineyard in Bento Gonçalves, RS, Brazil, from October 2008 to February 2009. Black oat (Avena strigosa and hairy vetch (Vicia villosa residues were collected, subjected to chemical (C, N, P, K, Ca, and Mg and biochemical (cellulose - Cel, hemicellulose - Hem, and lignin - Lig content analyses, and placed in litter bags, which were deposited in vines rows without plastic shelter (VPRWS, in vines rows with plastic shelter (VPRS, and in the between-row areas (BR. We collected the residues at 0, 33, 58, 76, and 110 days after deposition of the litter bags, prepared the material, and subjected it to analysis of total N, P, K, Ca, and Mg content. The VPRS contained the largest quantities and percentages of dry matter and residual nutrients (except for Ca in black oat residues from October to February, which coincides with the period from flowering up to grape harvest. This practice led to greater protection of the soil surface, avoiding surface runoff of the solution derived from between the rows, but it retarded nutrient cycling. The rate of biomass decomposition and nutrient release from hairy vetch residues from October to February was not affected by the position of deposition of the residues in the vineyard, which may especially be attributed to the lower values of the C/N and Lig/N ratios. Regardless of the type of residue, black oat or hairy vetch, the greatest decomposition and nutrient release mainly occurred up to 33 days after deposition of the residues on the soil surface, which coincided with the

  15. INVESTIGATION OF DRUG RELEASE FROM BIODEGRADABLE PLG MICROSPHERES: EXPERIMENT AND THEORY

    Energy Technology Data Exchange (ETDEWEB)

    ANDREWS, MALCOLM J. [Los Alamos National Laboratory; BERCHANE, NADER S. [Los Alamos National Laboratory; CARSON, KENNETH H. [Los Alamos National Laboratory; RICE-FICHT, ALLISON C. [Los Alamos National Laboratory

    2007-01-30

    Piroxicam containing PLG microspheres having different size distributions were fabricated, and in vitro release kinetics were determined for each preparation. Based on the experimental results, a suitable mathematical theory has been developed that incorporates the effect of microsphere size distribution and polymer degradation on drug release. We show from in vitro release experiments that microsphere size has a significant effect on drug release rate. The initial release rate decreased with an increase in microsphere size. In addition, the release profile changed from first order to concave-upward (sigmoidal) as the system size was increased. The mathematical model gave a good fit to the experimental release data.

  16. Subtask 1.16-Slow-Release Bioremediation Accelerators

    International Nuclear Information System (INIS)

    Marc D. Kurz; Edwin S. Olson

    2006-01-01

    Low-cost methods are needed to enhance various bioremediation technologies, from natural attenuation to heavily engineered remediation of subsurface hydrocarbon contamination. Many subsurface sites have insufficient quantities of nitrogen and phosphorus, resulting in poor bioactivity and increased remediation time and costs. The addition of conventional fertilizers can improve bioactivity, but often the nutrients dissolve quickly and migrate away from the contaminant zone before being utilized by the microbes. Through this project, conducted by the Energy and Environmental Research Center, polymers were developed that slowly release nitrogen and phosphorus into the subsurface. Conceptually, these polymers are designed to adhere to soil particles in the subsurface contamination zone where they slowly degrade and release nutrients over longer periods of time compared to conventional fertilizer applications. Tests conducted during this study indicate that some of the developed polymers have excellent potential to satisfy the microbial requirements for enhanced bioremediation

  17. Subtask 1.16-Slow-Release Bioremediation Accelerators

    Energy Technology Data Exchange (ETDEWEB)

    Marc D. Kurz; Edwin S. Olson

    2006-07-31

    Low-cost methods are needed to enhance various bioremediation technologies, from natural attenuation to heavily engineered remediation of subsurface hydrocarbon contamination. Many subsurface sites have insufficient quantities of nitrogen and phosphorus, resulting in poor bioactivity and increased remediation time and costs. The addition of conventional fertilizers can improve bioactivity, but often the nutrients dissolve quickly and migrate away from the contaminant zone before being utilized by the microbes. Through this project, conducted by the Energy & Environmental Research Center, polymers were developed that slowly release nitrogen and phosphorus into the subsurface. Conceptually, these polymers are designed to adhere to soil particles in the subsurface contamination zone where they slowly degrade and release nutrients over longer periods of time compared to conventional fertilizer applications. Tests conducted during this study indicate that some of the developed polymers have excellent potential to satisfy the microbial requirements for enhanced bioremediation.

  18. The radiological significance of beta emitting hot particles released from the Chernobyl nuclear power plant

    International Nuclear Information System (INIS)

    Hofmann, W.; Crawford-Brown, D.J.; Martonen, T.B.

    1988-01-01

    In order to assess radiological hazards associated with inhalation of beta emitting hot particles detected in fall-out from the Chernobyl incident, radiation doses and lung cancer risk are calculated for a hot particle composed entirely of 103 Ru. Lung cancer risk estimates are based upon an initiation-promotion model of carcinogenesis. In the immediate vicinity of a hot particle, calculations indicate that doses may be extremely high, so that all cells are killed and no tumour will arise. At intermediate distances, however, the probability for lung cancer induction exhibits a distinct maximum. Risk enhancement factors, computed relative to a uniform radionuclide distribution of equal activity, are highest for intermediate activities and hot particles moving in the lung. While the risk from inhalation of 103 Ru hot particles might, indeed, exceed that from all other exposure pathways of the Chernobyl fall-out, it still lies within normal fluctuations of radon progeny induced lung cancer risk. (author)

  19. The significance of ground contamination following an accidental release of radioactivity

    International Nuclear Information System (INIS)

    Corbett, J.O.

    1977-07-01

    The reasons for extending the analysis of hypothetical accidents to include ground contamination as a route to radiation dosage in man are discussed. Models and data available for such an assessment of ground contamination are examined with reference to the deposition of radionuclides from the atmosphere and dosage by direct γ-irradiation, ingestion of radionuclides in milk and inhalation of a resuspended aerosol. Dosage through these routes is then compared with that which arises directly from the plume emitted in a hypothetical accident. The assessment methods are subject to uncertainty, so that in some cases only an upper limit to dose or an estimate within an order of magnitude can be obtained. Areas where further research could lead to a reduction of this uncertainty are identified. (author)

  20. Release strategies for rehabilitated sea otters

    Science.gov (United States)

    DeGange, Anthony R.; Ballachey, Brenda E.; Bayha, Keith; Williams, Terrie M.; Davis, Randall W.

    1995-01-01

    According to the U.S. Fish and Wildlife Services’ (USFWS) Response Plan for sea otters (USFWS, in preparation), in the event of an oil spill, the decision to release sea otters from rehabilitation centers following treatment will be linked to the decision on whether to capture sea otters for treatment. Assuming a scenario similar to the Exxon Valdez oil spill (EVOS), once the decision to capture sea otters is made, the ultimate goal is to return as many sea otters to the wild as possible, even though the rescue may not be expected to produce results significant at the population level. The decision by the USFWS to proceed with capture, rehabilitation, and release will be made on a case-by-case basis (USFWS, in preparation). Many factors will influence the decision. Perhaps the most important factors in deciding when and where to release sea otters are the location and availability of suitable release sites and verification that the otters are free of diseases that might be transmitted to the wild population.Alternative release strategies for sea otters will be contained in the sea otter response portion of the USFWS’s oil spill contingency plans for Alaska and California that are being developed as required by the Oil Pollution Act of 1990. Public review of these plans before they are implemented will help to reduce public concern about the survival of rehabilitated otters, their biological effect on the release area, and the potential introduction or spread of disease into the wild sea otter population.The objective of this chapter is to review alternative strategies for the disposition of rehabilitated sea otters. Our assumption is that returning as many animals to the wild as possible, whether it be for humanitarian or biological reasons, is the ultimate goal of this effort (Figure 10.1).

  1. Controlled release system for ametryn using polymer microspheres: Preparation, characterization and release kinetics in water

    International Nuclear Information System (INIS)

    Grillo, Renato; Pereira, Anderson do Espirito Santo; Ferreira Silva de Melo, Nathalie; Porto, Raquel Martins; Feitosa, Leandro Oliveira; Tonello, Paulo Sergio; Dias Filho, Newton L.; Rosa, Andre Henrique; Lima, Renata; Fraceto, Leonardo Fernandes

    2011-01-01

    The purpose of this work was to develop a modified release system for the herbicide ametryn by encapsulating the active substance in biodegradable polymer microparticles produced using the polymers poly(hydroxybutyrate) (PHB) or poly(hydroxybutyrate-valerate) (PHBV), in order to both improve the herbicidal action and reduce environmental toxicity. PHB or PHBV microparticles containing ametryn were prepared and the efficiencies of herbicide association and loading were evaluated, presenting similar values of approximately 40%. The microparticles were characterized by scanning electron microscopy (SEM), which showed that the average sizes of the PHB and PHBV microparticles were 5.92 ± 0.74 μm and 5.63 ± 0.68 μm, respectively. The ametryn release profile was modified when it was encapsulated in the microparticles, with slower and more sustained release compared to the release profile of pure ametryn. When ametryn was associated with the PHB and PHBV microparticles, the amount of herbicide released in the same period of time was significantly reduced, declining to 75% and 87%, respectively. For both types of microparticle (PHB and PHBV) the release of ametryn was by diffusion processes due to anomalous transport (governed by diffusion and relaxation of the polymer chains), which did not follow Fick's laws of diffusion. The results presented in this paper are promising, in view of the successful encapsulation of ametryn in PHB or PHBV polymer microparticles, and indications that this system may help reduce the impacts caused by the herbicide, making it an environmentally safer alternative.

  2. Sustained release of radioprotective agents

    International Nuclear Information System (INIS)

    Shani, J.

    1980-11-01

    New pharmaceutical formulations for the sustained release into the G.I. tract of radioprotective agents have been developed by the authors. The experimental method initially consisted in the production of methylcellulose microcapsules. This method failed apparently because of the premature ''explosion'' of the microcapsules and the consequent premature release of massive amounts of the drug. A new method has been developed which consists in drying and pulverising cysteamine and cysteine preparations, mixing them in various proportions with stearic acid and ethylcellulose as carriers. The mixture is then compressed into cylindrical tablets at several pressure values and the leaching rate of the radioprotective agents is then measured by spectrophotometry. The relation between the concentration of the active drug and its rate of release, and the effect on the release rate of the pressure applied to the tablet during its formation were also investigated. Results indicating that the release rate was linearly related to the square root of ''t'' seem to be in agreement with what is predictable, according to Higuchi's equation, save for the very initial and terminal phases. A clear correlation was also established between the stearic acid/ethylcellulose ratios and the release of 20% cysteine, namely a marked decrease in the rate of cysteine release was observed with increasing concentrations of stearic acid. Finally, it was observed that a higher formation pressure results in quicker release of the drug

  3. Press Oil Final Release Survey

    Energy Technology Data Exchange (ETDEWEB)

    Whicker, Jeffrey Jay [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Ruedig, Elizabeth [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2017-05-11

    There are forty-eight 55 gallon barrels filled with hydraulic oil that are candidates for release and recycle. This oil needs to be characterized prior to release. Principles of sampling as provided in MARSAME/MARSSIM approaches were used as guidance for sampling.

  4. Workload Control with Continuous Release

    NARCIS (Netherlands)

    Phan, B. S. Nguyen; Land, M. J.; Gaalman, G. J. C.

    2009-01-01

    Workload Control (WLC) is a production planning and control concept which is suitable for the needs of make-to-order job shops. Release decisions based on the workload norms form the core of the concept. This paper develops continuous time WLC release variants and investigates their due date

  5. The Influence of Season on the Cow Milk Quantity, Quality and Hygiene

    Directory of Open Access Journals (Sweden)

    Ludovic Toma Cziszter

    2012-10-01

    Full Text Available The purpose of this study was to evaluate the effects of season of collection on the quantity, quality and hygienicproperties of the raw milk delivered from one dairy farm. The studied traits were: bulk tank milk yield, chemicalcomposition (fat, protein, lactose, and total solids, freezing point, density, total bacteria count, coliform bacteriacount and somatic cell count, during years 2010 and 2011. A total of 727 samples were drawn and analysed in twolaboratories, using the standard methods. Average milk production per day per head in the farm was 13.58 kg,obtained from 252 cows. Year of collection had a significant effect on the bulk tank raw milk yield, quality andhygiene, except for freezing point and total bacteria count. The raw milk yield and chemical composition improved(p<0.05 from year 2010 to year 2011, as well as the hygienic quality. Season of collection had a significant (p<0.05influence on the milk yield and chemical composition, the highest milk yield with the lowest concentration beingobtained during summer, while the lowest milk yield with the highest chemical composition was obtained in winter.Physical properties of the raw milk were less affected by the season of collection, with the lowest freezing point inthe winter and the highest density in the autumn. The highest somatic cell count and coliform bacteria count wasobtained during the spring and the lowest total bacteria count was obtained in winter season. There was a significant(p<0.05 interaction between year and season of production for all raw milk traits.

  6. Quantity and configuration of available elephant habitat and related conservation concerns in the Lower Kinabatangan floodplain of Sabah, Malaysia.

    Directory of Open Access Journals (Sweden)

    Jason G Estes

    Full Text Available The approximately 300 (298, 95% CI: 152-581 elephants in the Lower Kinabatangan Managed Elephant Range in Sabah, Malaysian Borneo are a priority sub-population for Borneo's total elephant population (2,040, 95% CI: 1,184-3,652. Habitat loss and human-elephant conflict are recognized as the major threats to Bornean elephant survival. In the Kinabatangan region, human settlements and agricultural development for oil palm drive an intense fragmentation process. Electric fences guard against elephant crop raiding but also remove access to suitable habitat patches. We conducted expert opinion-based least-cost analyses, to model the quantity and configuration of available suitable elephant habitat in the Lower Kinabatangan, and called this the Elephant Habitat Linkage. At 184 km(2, our estimate of available habitat is 54% smaller than the estimate used in the State's Elephant Action Plan for the Lower Kinabatangan Managed Elephant Range (400 km(2. During high flood levels, available habitat is reduced to only 61 km(2. As a consequence, short-term elephant densities are likely to surge during floods to 4.83 km(-2 (95% CI: 2.46-9.41, among the highest estimated for forest-dwelling elephants in Asia or Africa. During severe floods, the configuration of remaining elephant habitat and the surge in elephant density may put two villages at elevated risk of human-elephant conflict. Lower Kinabatangan elephants are vulnerable to the natural disturbance regime of the river due to their limited dispersal options. Twenty bottlenecks less than one km wide throughout the Elephant Habitat Linkage, have the potential to further reduce access to suitable habitat. Rebuilding landscape connectivity to isolated habitat patches and to the North Kinabatangan Managed Elephant Range (less than 35 km inland are conservation priorities that would increase the quantity of available habitat, and may work as a mechanism to allow population release, lower elephant density, reduce

  7. Economic production quantity concerning learning and the reworking of imperfect items

    Directory of Open Access Journals (Sweden)

    Tsai Deng-Maw

    2012-01-01

    Full Text Available The classical economic production quantity (EPQ model assumes that items produced are of perfect quality and the production rate is constant. However, production quality depends on the condition of the process. Due to process deterioration or other factors, the production process may shift and produce imperfect quality items. These imperfect quality items sometimes can be reworked and repaired; hence, overall production-inventory costs can be reduced significantly. In addition, it can be found in practice that the time or cost required to repetitively produce a unit of a product decreases when the number of units produced by a worker or a group of workers increases. Under this circumstance, the unit production cost cannot be regarded as constant and, therefore, cannot be ignored when taking account of the total cost. This paper incorporates the effects of learning and the reworking of defective items on the EPQ model since they were not considered in existing models. An optimal operation policy that minimizes the expected total cost per unit time is derived. A numerical example is provided to illustrate the proposed model. In addition, sensitivity analysis is performed and discussed.

  8. Unexpected seasonality in quantity and composition of Amazon rainforest air reactivity.

    Science.gov (United States)

    Nölscher, A C; Yañez-Serrano, A M; Wolff, S; de Araujo, A Carioca; Lavrič, J V; Kesselmeier, J; Williams, J

    2016-01-22

    The hydroxyl radical (OH) removes most atmospheric pollutants from air. The loss frequency of OH radicals due to the combined effect of all gas-phase OH reactive species is a measureable quantity termed total OH reactivity. Here we present total OH reactivity observations in pristine Amazon rainforest air, as a function of season, time-of-day and height (0-80 m). Total OH reactivity is low during wet (10 s(-1)) and high during dry season (62 s(-1)). Comparison to individually measured trace gases reveals strong variation in unaccounted for OH reactivity, from 5 to 15% missing in wet-season afternoons to mostly unknown (average 79%) during dry season. During dry-season afternoons isoprene, considered the dominant reagent with OH in rainforests, only accounts for ∼20% of the total OH reactivity. Vertical profiles of OH reactivity are shaped by biogenic emissions, photochemistry and turbulent mixing. The rainforest floor was identified as a significant but poorly characterized source of OH reactivity.

  9. Amending greenroof soil with biochar to affect runoff water quantity and quality

    Energy Technology Data Exchange (ETDEWEB)

    Beck, Deborah A.; Johnson, Gwynn R. [Portland State University, Mechanical and Materials Engineering, POB 751, Portland, OR 97207 (United States); Spolek, Graig A., E-mail: graig@cecs.pdx.edu [Portland State University, Mechanical and Materials Engineering, POB 751, Portland, OR 97207 (United States)

    2011-08-15

    Numbers of greenroofs in urban areas continue to grow internationally; so designing greenroof soil to reduce the amount of nutrients in the stormwater runoff from these roofs is becoming essential. This study evaluated changes in extensive greenroof water discharge quality and quantity after adding biochar, a soil amendment promoted for its ability to retain nutrients in soils and increase soil fertility. Prototype greenroof trays with and without biochar were planted with sedum or ryegrass, with barren soil trays used as controls. The greenroof trays were subjected to two sequential 7.4 cm/h rainfall events using a rain simulator. Runoff from the rain events was collected and evaluated. Trays containing 7% biochar showed increased water retention and significant decreases in discharge of total nitrogen, total phosphorus, nitrate, phosphate, and organic carbon. The addition of biochar to greenroof soil improves both runoff water quality and retention. - Highlights: > Biochar in green roof soil reduces nitrogen and phosphorus in the runoff. > Addition of biochar reduces turbidity of runoff. > Addition of biochar reduces total organic carbon content in runoff by 67-72%. > Biochar improves water retention of saturated soil. - In this controlled laboratory experiment, greenroof soil was amended by the addition of biochar, which reduced the water runoff concentration of nitrogen, phosphorus, and organic carbon.

  10. The importance of food quantity and quality for reproductive performance in alpine water pipits (Anthus spinoletta).

    Science.gov (United States)

    Brodmann, Paul A; Reyer, H-U; Bollmann, Kurt; Schläpfer, Alex R; Rauter, Claudia

    1997-01-01

    Studies relating reproduction to food availability are usually restricted to food quantity, but ignore food quality and the effects of habitat structure on obtaining the food. This is particularly true for insectivorous birds. In this study we relate measures of reproductive success, time of reproduction and nestling size of water pipits (Anthus spinoletta) to biomass, taxonomic composition and nutritional content of available food, and to vegetation structure and distance to feeding sites. Clutch size was positively correlated with the proportion of grass at the feeding sites, which facilitates foraging. This suggests that water pipits adapt their clutch size to environmental conditions. Also, pipits started breeding earlier and produced more fledglings when abundant food and a large proportion of grass were available, probably because these conditions allow the birds to gain more energy in less time. The number of fledglings was positively correlated with the energy content of available food. No significant relationships were found between feeding conditions and nestling size or the time that nestlings took to fledge. This suggests that water pipits do not invest more in individual nestlings when food conditions are favourable but rather start breeding earlier and produce more young. Taxonomic composition and nutritional content of prey were not correlated with any of the reproductive parameters, indicating that profitability rather than quality of food affects reproductive success.

  11. MATERNAL ALCOHOL CONSUMPTION PRODUCING FETAL ALCOHOL SPECTRUM DISORDERS (FASD): QUANTITY, FREQUENCY, AND TIMING OF DRINKING

    Science.gov (United States)

    May, Philip A.; Blankenship, Jason; Marais, Anna-Susan; Gossage, J. Phillip; Kalberg, Wendy O.; Joubert, Belinda; Cloete, Marise; Barnard, Ronel; De Vries, Marlene; Hasken, Julie; Robinson, Luther K.; Adnams, Colleen M.; Buckley, David; Manning, Melanie; Parry, Charles; Hoyme, H. Eugene; Tabachnick, Barbara; Seedat, Soraya

    2013-01-01

    Background Concise, accurate measures of maternal prenatal alcohol use are needed to better understand fetal alcohol spectrum disorders (FASD). Methods Measures of drinking by mothers of children with specific FASD diagnoses and mothers of randomly-selected controls are compared and also correlated with physical and cognitive/behavioral outcomes. Results Measures of maternal alcohol use can differentiate maternal drinking associated with FASD from that of controls and some from mothers of alcohol-exposed normals. Six variables that combine quantity and frequency concepts distinguish mothers of FASD children from normal controls. Alcohol use variables, when applied to each trimester and three months prior to pregnancy, provide insight on critical timing of exposure as well. Measures of drinking, especially bingeing, correlate significantly with increased child dysmorphology and negative cognitive/behavioral outcomes in children, especially low non-verbal IQ, poor attention, and behavioral problems. Logistic regression links (palcohol consumption both within and between diagnostic groupings of mothers bearing children diagnosed within the FASD continuum. Drinking measures are empirically identified and correlated with specific child outcomes. Alcohol use, especially heavy use, should be avoided throughout pregnancy. PMID:23932841

  12. The effect of quantity of added eggs on whole meal pasta quality

    Directory of Open Access Journals (Sweden)

    Filipović Jelena S.

    2014-01-01

    Full Text Available This paper investigates the convenience of different chemical and rheological methods for determining the quality of two spelt cultivars for pasta making and the influence of egg quantity on whole meal pasta quality. Post-hoc Tukey’s HSD test at 95% confidence limit has been calculated to show significant differences between different samples. Score analysis is being useful tool for accessing the effect of eggs to spelt pasta quality, and this analysis proved that though lower scores (0.270 for rheological characteristics experienced with cultivar Eco, the addition of eggs is positively contributing to the spelt pasta quality yielding the best score for pasta (0.75, contrary to the cultivar Austria attributed with superior rheology scores. Whole meal spelt is characterised by lower Ca, but higher Fe and Mn content in comparison to bread wheat. In comparison with common pasta, spelt is a suitable raw material for a new product with improved functional properties at the market.[Projekat Ministarstva nauke Republike Srbije, br. TRI 46005 i br. TR 31055

  13. Amending greenroof soil with biochar to affect runoff water quantity and quality

    International Nuclear Information System (INIS)

    Beck, Deborah A.; Johnson, Gwynn R.; Spolek, Graig A.

    2011-01-01

    Numbers of greenroofs in urban areas continue to grow internationally; so designing greenroof soil to reduce the amount of nutrients in the stormwater runoff from these roofs is becoming essential. This study evaluated changes in extensive greenroof water discharge quality and quantity after adding biochar, a soil amendment promoted for its ability to retain nutrients in soils and increase soil fertility. Prototype greenroof trays with and without biochar were planted with sedum or ryegrass, with barren soil trays used as controls. The greenroof trays were subjected to two sequential 7.4 cm/h rainfall events using a rain simulator. Runoff from the rain events was collected and evaluated. Trays containing 7% biochar showed increased water retention and significant decreases in discharge of total nitrogen, total phosphorus, nitrate, phosphate, and organic carbon. The addition of biochar to greenroof soil improves both runoff water quality and retention. - Highlights: → Biochar in green roof soil reduces nitrogen and phosphorus in the runoff. → Addition of biochar reduces turbidity of runoff. → Addition of biochar reduces total organic carbon content in runoff by 67-72%. → Biochar improves water retention of saturated soil. - In this controlled laboratory experiment, greenroof soil was amended by the addition of biochar, which reduced the water runoff concentration of nitrogen, phosphorus, and organic carbon.

  14. Advances and patents about grinding equipments with nano-particle jet minimum quantity lubrication.

    Science.gov (United States)

    Jia, Dongzhou; Li, Changhe; Wang, Sheng; Zhang, Qiang; Hou, Yali

    2014-01-01

    In recent years, a large number of patents have been devoted to developing minimum quantity lubrication (MQL) grinding techniques that can significantly improve both environmentally conscious and energy saving and costeffective sustainable grinding fluid alternatives. Among them, one patent is about a controllable nano-fluids jet MQL grinding system based on electrostatic atomization. Using the principle of electrostatics, it can achieve the control of droplet transfer by charging the sprayed droplets. This system can improve the uniformity of the droplet spectrum, liquid deposition efficiency and effective utilization of liquid. It can also effectively control the movement patterns of the droplets, thereby reducing the pollution of the environment and providing better health protection for workers. Although researchers accomplished profound and systematic studies on MQL, especially on nano-particles jet MQL. It can solve the shortage of MQL in cooling performance, greatly improve the working environment, save energy and reduce costs to achieve a low-carbon manufacturing. The unique lubricating performance and tribological property of solid nano-particles form nano-particle shearing films at the grinding wheel/workpiece interface, which can enhance the lubricating performance of MQL grinding. Existing studies on MQL grinding equipments, however, cannot meet the needs of the technological development. Therefore, our research provided a general introduction of the latest patients and research progress of nanoparticles jet MQL grinding equipments presented by the research team from Qingdao Technological University.

  15. Bee pollination increases yield quantity and quality of cash crops in Burkina Faso, West Africa.

    Science.gov (United States)

    Stein, Katharina; Coulibaly, Drissa; Stenchly, Kathrin; Goetze, Dethardt; Porembski, Stefan; Lindner, André; Konaté, Souleymane; Linsenmair, Eduard K

    2017-12-18

    Mutualistic biotic interactions as among flowering plants and their animal pollinators are a key component of biodiversity. Pollination, especially by insects, is a key element in ecosystem functioning, and hence constitutes an ecosystem service of global importance. Not only sexual reproduction of plants is ensured, but also yields are stabilized and genetic variability of crops is maintained, counteracting inbreeding depression and facilitating system resilience. While experiencing rapid environmental change, there is an increased demand for food and income security, especially in sub-Saharan communities, which are highly dependent on small scale agriculture. By combining exclusion experiments, pollinator surveys and field manipulations, this study for the first time quantifies the contribution of bee pollinators to smallholders' production of the major cash crops, cotton and sesame, in Burkina Faso. Pollination by honeybees and wild bees significantly increased yield quantity and quality on average up to 62%, while exclusion of pollinators caused an average yield gap of 37% in cotton and 59% in sesame. Self-pollination revealed inbreeding depression effects on fruit set and low germination rates in the F1-generation. Our results highlight potential negative consequences of any pollinator decline, provoking risks to agriculture and compromising crop yields in sub-Saharan West Africa.

  16. Information Needs Expressed During Patient-Oriented Oncology Consultations: Quantity, Variation, and Barriers.

    Science.gov (United States)

    Ahamad, Anesa; Wallner, Paul; Salenius, Sharon; Ross, Rudi; Fernandez, Eduardo

    2018-02-12

    High-quality oncology consultation includes patient-oriented communication tailored to patients' individualized needs. Common methods used in studies to increase question-asking are prompt lists and coaching pre-consultations. However, our patients were encouraged to ask questions by the physician during their visit. We aimed to estimate the quantity, nature, and variation of their questions when they were invited to ask by their oncologist. During radiotherapy consultations from 2012 to 2016, patient's questions were deliberately elicited and physician-transcribed. We derived mean and median number of questions per patient, variance by patient factors, and a taxonomy of subjects using thematic analysis. Three hundred ninety-six patients asked 2386 questions, median asked per patient = 6 (interquartile range = 4). We found significant variance with age (mean = 6.9 questions for  10% of patients and 40 topics were asked by < 10% of patients. With median of 6 questions, it is practicable to routinely elicit and address individualized information needs. Potential barriers may be older and underinsured patients. The wide variety of topics, often pertaining to individuals' case, suggests that cancer clinicians should take time-out during consultation to elicit patients' questions to accomplish best-practice communication.

  17. Study of dimensionless quantities to analyse front and rear wall of ...

    Indian Academy of Sciences (India)

    hydrodynamic quantities describe the mechanism behind flow pattern present in .... beam is focused into a small spot adjustable approximately 0.1 to 0.8 mm in ... moves, the liquefied metal around the 'keyhole' flows back in, solidifying and.

  18. The effect of vial type and cocktail quantity on tritium measurement in LSC

    International Nuclear Information System (INIS)

    Chen Zhilin; Xing Shixiong; Wang Heyi; Chang Ruimin; Wu Guanyin; Zhou Yinhang

    2010-01-01

    The effect of sample vial type and cocktail quantity on tritium measurement in liquid scintillation counting is studied in this paper. With both high and low level tritium samples, glass vials allow higher counting rates than plastic vials do. We also present detailed analysis of the way to obtain the optimal counting condition by dispensing different quantity of cocktail into sample vials. Results indicate that the optimal counting condition has little relationship with tritium concentration in the sample. The main factor which influences the counting is the quantity of cocktail added into samples. Figure of merit is employed to access the results, which increases as the quantity of cocktail increasing. But when the ratio of cocktail and sample reaches 2.0, increase of ratio makes little contribution to the counts, and the disintegrations per minute comes nearly to be a constant.

  19. Effects of Fuel Quantity on Soot Formation Process for Biomass-Based Renewable Diesel Fuel Combustion

    KAUST Repository

    Jing, Wei; Wu, Zengyang; Roberts, William L.; Fang, Tiegang

    2016-01-01

    Soot formation process was investigated for biomass-based renewable diesel fuel, such as biomass to liquid (BTL), and conventional diesel combustion under varied fuel quantities injected into a constant volume combustion chamber. Soot measurement

  20. 3D facial expression recognition based on histograms of surface differential quantities

    KAUST Repository

    Li, Huibin; Morvan, Jean-Marie; Chen, Liming

    2011-01-01

    . To characterize shape information of the local neighborhood of facial landmarks, we calculate the weighted statistical distributions of surface differential quantities, including histogram of mesh gradient (HoG) and histogram of shape index (HoS). Normal cycle