WorldWideScience

Sample records for release significant amounts

  1. Permafrost Stores a Globally Significant Amount of Mercury

    Science.gov (United States)

    Schuster, Paul F.; Schaefer, Kevin M.; Aiken, George R.; Antweiler, Ronald C.; Dewild, John F.; Gryziec, Joshua D.; Gusmeroli, Alessio; Hugelius, Gustaf; Jafarov, Elchin; Krabbenhoft, David P.; Liu, Lin; Herman-Mercer, Nicole; Mu, Cuicui; Roth, David A.; Schaefer, Tim; Striegl, Robert G.; Wickland, Kimberly P.; Zhang, Tingjun

    2018-02-01

    Changing climate in northern regions is causing permafrost to thaw with major implications for the global mercury (Hg) cycle. We estimated Hg in permafrost regions based on in situ measurements of sediment total mercury (STHg), soil organic carbon (SOC), and the Hg to carbon ratio (RHgC) combined with maps of soil carbon. We measured a median STHg of 43 ± 30 ng Hg g soil-1 and a median RHgC of 1.6 ± 0.9 μg Hg g C-1, consistent with published results of STHg for tundra soils and 11,000 measurements from 4,926 temperate, nonpermafrost sites in North America and Eurasia. We estimate that the Northern Hemisphere permafrost regions contain 1,656 ± 962 Gg Hg, of which 793 ± 461 Gg Hg is frozen in permafrost. Permafrost soils store nearly twice as much Hg as all other soils, the ocean, and the atmosphere combined, and this Hg is vulnerable to release as permafrost thaws over the next century. Existing estimates greatly underestimate Hg in permafrost soils, indicating a need to reevaluate the role of the Arctic regions in the global Hg cycle.

  2. Permafrost stores a globally significant amount of mercury

    Science.gov (United States)

    Schaefer, K. M.; Schuster, P. F.; Antweiler, R.; Aiken, G.; DeWild, J.; Gryziec, J. D.; Gusmeroli, A.; Hugelius, G.; Jafarov, E.; Krabbenhoft, D. P.; Liu, L.; Herman-Mercer, N. M.; Mu, C.; Roth, D. A.; Schaefer, T.; Striegl, R. G.; Wickland, K.; Zhang, T.

    2017-12-01

    Changing climate in northern regions is causing permafrost to thaw with major implications for the cycling of mercury in arctic and subarctic ecosystems. Permafrost occurs in nearly one quarter of the Earth's Northern Hemisphere. We measured total soil mercury concentration in 588 samples from 13 soil permafrost cores from the interior and the North Slope of Alaska. The median concentration was 47.7±23.4 ng Hg g soil-1 and the median ratio of Hg to carbon was 1.56±0.86 µg Hg g C-1. We estimate Alaskan permafrost stores 56±32 kilotons of mercury and the entire northern hemisphere permafrost land mass stores 773±441 kilotons of mercury. This increases estimates of mercury stored in soils by 60%, making permafrost the second largest reservoir of mercury on the planet. Climate projections indicate extensive permafrost thawing, releasing mercury into the environment through a variety of mechanisms, for example, terrestrial transport via dissolved organic carbon (DOC), gaseous elemental mercury (GEM) evasion, forest fires, atmospheric mixing processes with ozone, and Springtime atmospheric Hg depletion after the polar sunrise. These findings have major implications for terrestrial and aquatic life, the world's fisheries, and ultimately human health.

  3. Permafrost stores a globally significant amount of mercury

    Science.gov (United States)

    Schuster, Paul F.; Schaefer, Kevin; Aiken, George R.; Antweiler, Ronald C.; DeWild, John F.; Gryziec, Joshua D.; Gusmeroli, Alessio; Hugelius, Gustaf; Jafarov, Elchin E.; Krabbenhoft, David P.; Liu, Lin; Herman-Mercer, Nicole M.; Mu, Cuicui; Roth, David A.; Schaefer, Tim; Striegl, Robert G.; Wickland, Kimberly P.; Zhang, Tingjun

    2018-01-01

    Changing climate in northern regions is causing permafrost to thaw with major implications for the global mercury (Hg) cycle. We estimated Hg in permafrost regions based on in situ measurements of sediment total mercury (STHg), soil organic carbon (SOC), and the Hg to carbon ratio (RHgC) combined with maps of soil carbon. We measured a median STHg of 43 ± 30 ng Hg g soil−1 and a median RHgC of 1.6 ± 0.9 μg Hg g C−1, consistent with published results of STHg for tundra soils and 11,000 measurements from 4,926 temperate, nonpermafrost sites in North America and Eurasia. We estimate that the Northern Hemisphere permafrost regions contain 1,656 ± 962 Gg Hg, of which 793 ± 461 Gg Hg is frozen in permafrost. Permafrost soils store nearly twice as much Hg as all other soils, the ocean, and the atmosphere combined, and this Hg is vulnerable to release as permafrost thaws over the next century. Existing estimates greatly underestimate Hg in permafrost soils, indicating a need to reevaluate the role of the Arctic regions in the global Hg cycle.

  4. Possible chaoticity for the time series of the amount of nuclear information released by the newsmedia

    International Nuclear Information System (INIS)

    Ohnishi, T.

    1995-01-01

    The amount of information concerning nuclear problems was time analysed which has been released by three types of the newsmedia in Japan, the press, television and magazines during the past 20 years. The time series of the logarithmic value of the amount released by some of the newsmedia was found to be possibly chaotic, or at least to be non-stochastic. Such a characteristic of time series can be interpreted as a result of the exertion of a certain sort of selection process in the interior of the newsmedia in deciding an event as news to be released. (author)

  5. Between Amount and Significance: The 'Capitalist' Aspect of Leisure

    Science.gov (United States)

    Gross, Zehavit

    2016-01-01

    The aim of this paper is to analyse the disparity between the time adolescents devote to various leisure activities and the significance they attribute to them. The gap between amount and significance mirrors the way that adolescents in Israel perceive the concept of leisure and the content with which they fill it. Leisure is a phenomenon that is…

  6. Zinc release from Schaffer collaterals and its significance.

    Science.gov (United States)

    Takeda, Atsushi; Nakajima, Satoko; Fuke, Sayuri; Sakurada, Naomi; Minami, Akira; Oku, Naoto

    2006-02-15

    On the basis of the evidence that approximately 45% of Schaffer collateral boutons are zinc-positive, zinc release from Schaffer collaterals and its action were examined in hippocampal slices. When zinc release from Schaffer collaterals was examined using ZnAF-2, a membrane-impermeable zinc indicator, ZnAF-2 signal in the stratum radiatum of the CA1 was increased by tetanic stimuli at 100 Hz for 1s, suggesting that zinc is released from Schaffer collaterals in a calcium- and impulse-dependent manner. An in vivo microdialysis experiment indicated that the perfusion with 10 microM zinc significantly decreases extracellular glutamate concentration in the CA1. When tetanic stimuli at 100 Hz for 5s were delivered to the dentate granule cells, the increase in calcium signal in the stratum radiatum of the CA1, as well as in the stratum lucidum of the CA3, was attenuated by addition of 10 microM zinc, while enhanced by addition of 1mM CaEDTA, a membrane-impermeable zinc chelator. The increase in calcium signal in the CA1, in which Schaffer collateral synapses exist, during delivery of tetanic stimuli at 100 Hz for 1s to the Schaffer collateral-commissural pathway was also significantly enhanced by addition of 1mM CaEDTA. These results suggest that zinc released from Schaffer collaterals suppressively modulates presynaptic and postsynaptic calcium signaling in the CA1, followed by the suppression of glutamate release.

  7. Effect of increased exposure times on amount of residual monomer released from single-step self-etch adhesives.

    Science.gov (United States)

    Altunsoy, Mustafa; Botsali, Murat Selim; Tosun, Gonca; Yasar, Ahmet

    2015-10-16

    The aim of this study was to evaluate the effect of increased exposure times on the amount of residual Bis-GMA, TEGDMA, HEMA and UDMA released from single-step self-etch adhesive systems. Two adhesive systems were used. The adhesives were applied to bovine dentin surface according to the manufacturer's instructions and were polymerized using an LED curing unit for 10, 20 and 40 seconds (n = 5). After polymerization, the specimens were stored in 75% ethanol-water solution (6 mL). Residual monomers (Bis-GMA, TEGDMA, UDMA and HEMA) that were eluted from the adhesives (after 10 minutes, 1 hour, 1 day, 7 days and 30 days) were analyzed by high-performance liquid chromatography (HPLC). The data were analyzed using 1-way analysis of variance and Tukey HSD tests. Among the time periods, the highest amount of released residual monomers from adhesives was observed in the 10th minute. There were statistically significant differences regarding released Bis-GMA, UDMA, HEMA and TEGDMA between the adhesive systems (p<0.05). There were no significant differences among the 10, 20 and 40 second polymerization times according to their effect on residual monomer release from adhesives (p>0.05). Increasing the polymerization time did not have an effect on residual monomer release from single-step self-etch adhesives.

  8. Comparison of the Amount of Fluoride Release from Nanofilled Resin Modified Glass Ionomer Conventional and Resin Modified Glass Ionomer Cements

    Directory of Open Access Journals (Sweden)

    Sumitha Upadhyay

    2013-01-01

    Full Text Available Objective: To investigate and compare the amount of fluoride release of conventional, resin modified and nanofilled resin modified glass ionomer cements.Materials and Methods: Tablets of glass-ionomer cements were immersed in deionized water and incubated at 37◦C. After 1, 2, 7, 15 and 30 days, fluoride ion was measured under normal atmospheric conditions by fluoride ion selective electrode. Buffer (TISAB II was used to decomplex the fluoride ion and to provide a constant background ionic strength and to maintain the pH of water between 5.0 and 5.5 as the fluoride electrode is sensitive to changes in pH. Statistical evaluation was carried out by one way ANOVA (Analysis of Variance using SPSS 11.0. The significance level was set at p< 0.05.Results: The release of fluoride was highest on day 1 and there was a sudden fall on day 2 in all three groups. Initially fluoride release from conven-tional glass-ionomer cement was highest compared to the other two glass-ionomer cements, but the amount drastically reduced over the period. Although the amount of fluoride release was less than both the resin modified and nanofilled resin modified glass-ionomer cement, the release was sustained consistently for 30 daysConclusion: The cumulative fluoride release of nanofilled resin modified glass ionomer cement was very less compared to the conventional and resin modified glass ionomer cements and Nanofilled resin modified glass ionomer cement released less but steady fluoride as compared to other resin modified glass ionomer cements.

  9. Evaluation of release amount of radioactivity from Chernobyl accident and of resulting radiological consequence in China

    International Nuclear Information System (INIS)

    Zhang Yongxing

    1987-01-01

    Three kinds of methods are used to evaluate the release amount from Chernoby1 RBMK-1000 reactor accident, i.e. (1) estimation by comparison with Windscale accident; (2) estimation in terms of the stock in the core; and (3) estimation according to the available monitoring data form adjacent countries such as Poland and Finland. The results obtained are as follows: the release of I-131 was 0.1-1.5 EBq, which is approximately 4-50% of the stock in the core; the release amount of Ru-103 was comparable to that of Cs-137, both approximately 5-10% of that of I-131; the volatile nuclides such as Mo-99, Ru-103, Te-132, Cs-137 etc., were in the order of 0.4 EBq; involatile nuclides were 0.2 EBq; noble gases and other fission products 10 EBq; and the total amount released was about 20 EBq, which taken together 8% of the stock in the core. The radioactive cloud cluster passed through over the area of China in the beginning of May. It was estimated that the total amount of I-131 in air over China area was about 1.6 PB q , Cs-137 about 0.3 PB q , Ru-103 about 0.2 PB q ; the total fallout in the area of China was about 3 PB q for I-131, about 0.1 PB q for Cs-137, about 0.3 PB q for Ru-103. The resulting effective dose equavalent commitment to critical group individual was about 60 μSv, collective effective dose equavalent commitment received by the population of China was about 1 x 10 4 man.Sv

  10. Environmental contamination due to release of a large amount of tritium

    International Nuclear Information System (INIS)

    Kawai, Hiroshi

    1988-01-01

    Tritium release incidents have occurred many times in the Savannah Rever Plant in the U.S. A tritium release incident also took place in the Lawrence Livermore Laboratory. The present article outlines the reports by the plant and laboratory on these incidents and makes some comments on environmental contamination that may results from release of a large amount of tritium from nuclear fusion facilities. Tritium is normally released in the form of a combination of chemical compounds such as HT, DT and T 2 and oxides such as HTO, DTO and T 2 O. The percentage of the oxides is given in the reports by the plant. Oxides, which can be absorbed through the skin, are considered to be nearly a thousand times more toxic than the other type of tritium compounds. The HT type compounds (HT, DT and T 2 ) can be oxidized by microorganisms in soil into oxides (HTO, DTO and T 2 O) and therefore, great care should also given to this type of compounds. After each accidental tritium release, the health physics group of the plant collected various environmental samples, including ground surface water, milk, leaves of plants, soil and human urine, in leeward areas. Results on the contamination of surface water, fish and underground water are outlined and discussed. (Nogami, K.)

  11. Heat shock protein 72: release and biological significance during exercise.

    Science.gov (United States)

    Whitham, Martin; Fortes, Matthew Benjamin

    2008-01-01

    The cumulative stressors of exercise manifest themselves at a cellular level by threatening the protein homeostasis of the cell. In these conditions, Heat Shock Proteins (HSP) are synthesised to chaperone mis-folded and denatured proteins. As such, the intracellular HSP response is thought to aid cell survival in the face of otherwise lethal cellular stress. Recently, the inducible isoform of the 70 Kda heat shock protein family, Hsp72 has been detected in the extracellular environment. Furthermore, the release of this protein into the circulation has been shown to occur in response to a range of exercise bouts. The present review summarises the current research on the exercise Hsp72 response, the possible mediators and mechanisms of extracellular (e)Hsp72 release, and the possible biological significance of this systemic response. In particular, the possible role of eHsp72 in the modulation of immunity during exercise is discussed.

  12. Crustacean zooplankton release copious amounts of dissolved organic matter as taurine in the ocean.

    Science.gov (United States)

    Clifford, Elisabeth L; Hansell, Dennis A; Varela, Marta M; Nieto-Cid, Mar; Herndl, Gerhard J; Sintes, Eva

    2017-11-01

    Taurine (Tau), an amino acid-like compound, is present in almost all marine metazoans including crustacean zooplankton. It plays an important physiological role in these organisms and is released into the ambient water throughout their life cycle. However, limited information is available on the release rates by marine organisms, the concentrations and turnover of Tau in the ocean. We determined dissolved free Tau concentrations throughout the water column and its release by abundant crustacean mesozooplankton at two open ocean sites (Gulf of Alaska and North Atlantic). At both locations, the concentrations of dissolved free Tau were in the low nM range (up to 15.7 nM) in epipelagic waters, declining sharply in the mesopelagic to about 0.2 nM and remaining fairly stable throughout the bathypelagic waters. Pacific amphipod-copepod assemblages exhibited lower dissolved free Tau release rates per unit biomass (0.8 ± 0.4 μmol g -1 C-biomass h -1 ) than Atlantic copepods (ranging between 1.3 ± 0.4 μmol g -1 C-biomass h -1 and 9.5 ± 2.1 μmol g -1 C-biomass h -1 ), in agreement with the well-documented inverse relationship between biomass-normalized excretion rates and body size. Our results indicate that crustacean zooplankton might contribute significantly to the dissolved organic matter flux in marine ecosystems via dissolved free Tau release. Based on the release rates and assuming steady state dissolved free Tau concentrations, turnover times of dissolved free Tau range from 0.05 d to 2.3 d in the upper water column and are therefore similar to those of dissolved free amino acids. This rapid turnover indicates that dissolved free Tau is efficiently consumed in oceanic waters, most likely by heterotrophic bacteria.

  13. Release measurement of great amount of waste. Conveyor belt versus wire mesh pallet systems

    Energy Technology Data Exchange (ETDEWEB)

    Sokcic-Kostic, Marina; Schultheis, Roland; Langer, Felix [NUKEM Technologies Engineering Services GmbH, Alzenau (Germany)

    2014-08-15

    Great amount of waste has to be measured for release during the decommissioning and rebuilding of nuclear facilities and installation. Since the enclosed storage or decontamination is very expensive it is advisable for economic reasons to separate contaminated material. The necessary measurement is however a time and cost intensive work which has carefully provided. There are two general methods to perform this task: one is a continuously running system on the basis of a conveyor belt system. The other approach is a discontinuously running system using wire mesh pallets. With the knowledge from existing installations this article will discuss the pro's and contra's and show the limits of the systems.

  14. [Significance of lateral release in the therapy of patellar chondromalacia].

    Science.gov (United States)

    Krüger, T; Göbel, F; Huschenbett, A; Hein, W

    2002-10-01

    A retrospective study was performed in 26 patients who underwent an operation for femoro-patellar pain due to a patellar chondromalacia with or without minor patellar dislocation/lateral pressure syndrome. The average age of the patients was 28.5 (15-39) years. 22 of the 26 patients revealed minor chondral damages of the stages 1 and 2 according to Outerbridge. In 12 patients ("lavage" group), an arthroscopic joint debridement only was carried out, while an additional open, lateral retinaculum release was made in 14 patients ("lateral release" group). The patella's distance of dislocation according to Hepp was reduced on an average of 3.0 (0-7) mm (p = 0.0019). The results of Bentley's score obtained during the follow-up interval on an average of 30.1 (9 to 60) months were almost identical for both groups. "Good" and "very good" results were achieved in the "lavage" group (83.3 %) and "lateral release" group (78.6 % of the patients). Lateral release should be used in cases of patellar decentration between 5 and 10 mm and adequate pain symptoms. The post-operative distance of dislocation should be less than 5 mm. Under such conditions and with minor chondral damage, a combined approach by using an arthroscopic joint debridement and open lateral release is promising to treat a patellar dislocation/lateral pressure syndrome.

  15. Sodium-Reduced Meat and Poultry Products Contain a Significant Amount of Potassium from Food Additives.

    Science.gov (United States)

    Parpia, Arti Sharma; Goldstein, Marc B; Arcand, JoAnne; Cho, France; L'Abbé, Mary R; Darling, Pauline B

    2018-05-01

    -sodium-reduced counterparts (mean difference [95% CI]: 486 [334-638]; Padditives appearing on the product label ingredient list, did not significantly differ between the two groups. Potassium additives are frequently added to sodium-reduced MPPs in amounts that significantly contribute to the potassium load for patients with impaired renal handling of potassium caused by chronic kidney disease and certain medications. Patients requiring potassium restriction should be counseled to be cautious regarding the potassium content of sodium-reduced MPPs and encouraged to make food choices accordingly. Copyright © 2018 Academy of Nutrition and Dietetics. Published by Elsevier Inc. All rights reserved.

  16. Method for optical 15N analysis of small amounts of nitrogen gas released from an automatic nitrogen analyzer

    International Nuclear Information System (INIS)

    Arima, Yasuhiro

    1981-01-01

    A method of optical 15 N analysis is proposed for application to small amounts of nitrogen gas released from an automatic nitrogen analyzer (model ANA-1300, Carlo Erba, Milano) subjected to certain set modifications. The ANA-1300 was combined with a vacuum line attached by a molecular sieve 13X column. The nitrogen gas released from the ANA-1300 was introduced with a carrier gas of helium into the molecular sieve column which was pre-evacuated at 10 -4 Torr and cooled with outer liquid nitrogen. After removal of the helium by evacuation, the nitrogen gas fixed on the molecular sieve was released by warming the column, and then, it was sealed into pre-evacuated pyrex glass tubes at 4.5 - 5.0 Torr. In the preparation of discharge tubes, contamination of unlabelled nitrogen occurred from the carrier gas of standard grade helium, and the relative lowering of the 15 N value by it was estimated to be less than 1% when over 700 μg nitrogen was charged on the ANA-1300; when 200 μg nitrogen was charged, it was about 3.5%. However, the effect of the contamination could be corrected for by knowing the amount of contaminant nitrogen. In the analysis of plant materials by the proposed method, the coefficient of variation was less than 2%, and no significant difference was observed between results given by the present method and by the ordinary method in which samples were directly pyrolyzed in the discharge tubes by the Dumas method. The present method revealed about 1.5 μg of cross-contaminated nitrogen and was applicable to more than 200 μg of sample nitrogen. (author)

  17. The significance of duration and amount of sodium reduction intervention in normotensive and hypertensive individuals

    DEFF Research Database (Denmark)

    Graudal, Niels; Hubeck-Graudal, Thorbjørn; Jürgens, Gesche

    2015-01-01

    The purpose of this meta-analysis was to establish the time for achievement of maximal blood pressure (BP) efficacy of a sodium reduction (SR) intervention and the relation between the amount of SR and the BP response in individuals with hypertension and normal BP. Relevant studies were retrieved.......12, P policy of sodium reduction....

  18. Influence of ultrasonic energy on dispersion of aggregates and released amounts of organic matter and polyvalent cations

    Science.gov (United States)

    Kaiser, M.; Kleber, M.; Berhe, A. A.

    2010-12-01

    Aggregates play important roles in soil carbon storage and stabilization. Identification of scale-dependent mechanisms of soil aggregate formation and stability is necessary to predict and eventually manage the flow of carbon through terrestrial ecosystems. Application of ultrasonic energy is a common tool to disperse soil aggregates. In this study, we used ultra sonic energy (100 to 2000 J cm-3) to determine the amount of polyvalent cations and organic matter involved in aggregation processes in three arable and three forest soils that varied in soil mineral composition. To determine the amount of organic matter and cations released after application of different amount of ultrasonic energy, we removed the coarse fraction (>250 µm). The remaining residue (solid residue freeze dried before we analyzed the amounts of water-extracted organic carbon (OC), Fe, Al, Ca, Mn, and Mg in the filtrates. The extracted OM and solid residues were further characterized by Fourier Transformed Infra Red spectroscopy and Scanning Electron Microscopy. Our results show a linear increase in amount of dissolved OC with increasing amounts of ultra sonic energy up to 1500 J cm-3 indicating maximum dispersion of soil aggregates at this energy level independent from soil type or land use. In contrast to Mn, and Mg, the amounts of dissolved Ca, Fe, and Al increase with increasing ultra sonic energy up to 1500 J cm-3. At 1500 J cm-3, the absolute amounts of OC, Ca, Fe, and Al released were specific for each soil type, likely indicating differences in type of OM-mineral interactions involved in micro-scaled aggregation processes. The amounts of dissolved Fe, and Al released after an application of 1500 J cm-3 are not related to oxalate- and dithionite- extractable, or total Al content indicating less disintegration of pedogenic oxides or clay minerals due to high levels of ultrasonic energy.

  19. Amount and timing of permafrost carbon release in response to climate warming

    Energy Technology Data Exchange (ETDEWEB)

    Schaefer, Kevin; Zhang, Tingjun; Barrett, Andrew P. (National Snow and Ice Data Center, Cooperative Inst. for Research in Environmental Sciences, Univ. of Colorado at Boulder, Boulder (United States)), e-mail: kevin.schaefer@nsidc.org; Bruhwiler, Lori (National Oceanic and Atmospheric Administration, Earth System Research Laboratory, Boulder (United States))

    2011-04-15

    The thaw and release of carbon currently frozen in permafrost will increase atmospheric CO{sub 2} concentrations and amplify surface warming to initiate a positive permafrost carbon feedback (PCF) on climate.We use surface weather from three global climate models based on the moderate warming, A1B Intergovernmental Panel on Climate Change emissions scenario and the SiBCASA land surface model to estimate the strength and timing of the PCF and associated uncertainty. By 2200, we predict a 29-59% decrease in permafrost area and a 53-97 cm increase in active layer thickness. By 2200, the PCF strength in terms of cumulative permafrost carbon flux to the atmosphere is 190 +- 64 Gt C. This estimate may be low because it does not account for amplified surface warming due to the PCF itself and excludes some discontinuous permafrost regions where SiBCASA did not simulate permafrost. We predict that the PCF will change the arctic from a carbon sink to a source after the mid-2020s and is strong enough to cancel 42-88% of the total global land sink. The thaw and decay of permafrost carbon is irreversible and accounting for the PCF will require larger reductions in fossil fuel emissions to reach a target atmospheric CO{sub 2} concentration

  20. Proposal of the concept of selection of accidents that release large amounts of radioactive substances in the high temperature engineering test reactor

    International Nuclear Information System (INIS)

    Ono, Masato; Honda, Yuki; Takada, Shoji; Sawa, Kazuhiro

    2015-01-01

    In Position, construction and equipment of testing and research reactor to be subjected to the use standards for rules Article 53 (prevention of expansion of the accident to release a large amount of radioactive material) generation the frequency is a lower accident than design basis accident, when what is likely to release a large amount of radioactive material or radiation from the facility has occurred, and take the necessary measures in order to prevent the spread of the accident. There is provided a lower accident than frequency design basis accidents, for those that may release a large amount of radioactive material or radiation. (author)

  1. Evaluation of the potential for significant ammonia releases from Hanford waste tanks

    International Nuclear Information System (INIS)

    Palmer, B.J.; Anderson, C.M.; Chen, G.; Cuta, J.M.; Ferryman, T.A.; Terrones, G.

    1996-07-01

    Ammonia is ubiquitous as a component of the waste stored in the Hanford Site single-shell tanks (SSTs) and double-shell tanks (DSTs). Because ammonia is both flammable and toxic, concerns have been raised about the amount of ammonia stored in the tanks and the possible mechanisms by which it could be released from the waste into the head space inside the tanks as well as into the surrounding atmosphere. Ammonia is a safety issue for three reasons. As already mentioned, ammonia is a flammable gas and may contribute to a flammability hazard either directly, if it reaches a high enough concentration in the tank head space, or by contributing to the flammability of other flammable gases such as hydrogen (LANL 1994). Ammonia is also toxic and at relatively low concentrations presents a hazard to human health. The level at which ammonia is considered Immediately Dangerous to Life or Health (IDLH) is 300 ppm (WHC 1993, 1995). Ammonia concentrations at or above this level have been measured inside the head space in a number of SSTs. Finally, unlike hydrogen and nitrous oxide, ammonia is highly soluble in aqueous solutions, and large amounts of ammonia can be stored in the waste as dissolved gas. Because of its high solubility, ammonia behaves in a qualitatively different manner from hydrogen or other insoluble gases. A broader range of scenarios must be considered in modeling ammonia storage and release

  2. Preliminary investigations of the significance of the ingestion pathway following accidental releases with actinides

    International Nuclear Information System (INIS)

    Steinhauer, C.

    1985-10-01

    Preliminary accident consequence assessments have been performed with the computer code UFOMOD to study the significance of the ingestion pathway in accidental releases with actinides. The investigation was based on the release category K1 of the 'Risk Oriented Analysis of the SNR 300', in which a higher fraction of actinides is released than in the worst release category for an LWR. The analysis was carried out using the currently implemented food chain transport model WASH-1400/BSU and data from the dynamic model from the MARC methodology. To study the influence of the time of the accident on the food chain-related results, releases in January and July were considered by means of the MARC data. In this report the differences are presented between both food chain transport models for transuranium elements and those which are observed in the potential doses due to ingestion, the areas affected by food-bans and the late health effects when using both models and taking the influence of the season into account. (orig./HP) [de

  3. The evaluation of failure stress and released amount of fission product gas of power ramped rod by fuel behaviour analysis code 'FEMAXI-III'

    International Nuclear Information System (INIS)

    Yanagisawa, Kazuaki; Fujita, Misao

    1984-01-01

    Pellet-Cladding Interaction(PCI) related in-pile failure of Zircaloy sheathed fuel rod is in general considered to be caused by combination of pellet-cladding mechanical interaction(PCMI) with fuel-cladding chemical interaction(FCCI). An understanding of a basic mechanism of PCI-related fuel failure is therefore necessary to get actual cladding hoop stress from mechanical interaction and released amounts of fission product(FP) gas of aggressive environmental agency from chemical interaction. This paper describes results of code analysis performed on fuel failure to cladding hoop stress and amounts of FP gas released under the condition associated with power ramping. Data from Halden(HBWR) and from Studsvik(R2) are used for code analysis. The fuel behaviour analysis code ''FEMAXI-III'' is used as an analytical tool. The followings are revealed from the study: (1) PCI-related fuel failure is dependent upon cladding hoop stress and released amounts of FP gas at power ramping. (2) Preliminary calculated threshold values of hoop stress and of released amounts of FP gas to PCI failure are respectively 330MPa, 10% under the Halden condition, 190MPa, 5% under the Inter ramp(BWR) condition, and 270MPa, 14% under the Over ramp(PWR) condition. The values of hoop stress calculated are almost in the similar range of those obtained from ex-reactor PCI simulated tests searched from references published. (3) The FEMAXI-III code verification is made in mechanical manner by using in-pile deformation data(diametral strain) obtained from power ramping test undertaken by JAERI. While, the code verification is made in thermal manner by using punctured FP gas data obtained from post irradiation examination performed on non-defected power ramped fuel rods. The calculations are resulted in good agreements to both, mechanical and thermal experimental data suggesting the validity of the code evaluation. (J.P.N.)

  4. 76 FR 71583 - Notice of Availability of Finding of No Significant Impact for Field Release of Insects for...

    Science.gov (United States)

    2011-11-18

    ... Finding of No Significant Impact for Field Release of Insects for Biological Control of Carrizo Cane... insects, the Arundo scale and the Arundo wasp as biological control agents for the non-native and invasive... [[Page 71584

  5. Significance of air humidity and air velocity for fungal spore release into the air

    Science.gov (United States)

    Pasanen, A.-L.; Pasanen, P.; Jantunen, M. J.; Kalliokoski, P.

    Our previous field studies have shown that the presence of molds in buildings does not necessarily mean elevated airborne spore counts. Therefore, we investigated the release of fungal spores from cultures of Aspergillus fumigatus, Penicillium sp. and Cladosporium sp. at different air velocities and air humidities. Spores of A. fumigatus and Penicillium sp. were released from conidiophores already at air velocity of 0.5 ms -1, whereas Cladosporium spores required at least a velocity of 1.0 ms -1. Airborne spore counts of A. fumigatus and Penicillium sp. were usually higher in dry than moist air, being minimal at relative humidities (r.h.) above 70%, while the effect of r.h. on the release of Cladosporium sp. was ambivalent. The geometric mean diameter of released spores increased when the r.h. exceeded a certain level which depends on fungal genus. Thus, spores of all three fungi were hygroscopic but the hygroscopicity of various spores appeared at different r.h.-ranges. This study indicates that spore release is controlled by external factors and depends on fungal genus which can be one reason for considerable variation of airborne spore counts in buildings with mold problems.

  6. Does the amount of tagged stool and fluid significantly affect the radiation exposure in low-dose CT colonography performed with an automatic exposure control?

    Energy Technology Data Exchange (ETDEWEB)

    Lim, Hyun Kyong; Lee, Kyoung Ho; Kim, So Yeon; Kim, Young Hoon [Seoul National University Bundang Hospital, Department of Radiology, Seongnam-si, Gyeonggi-do (Korea, Republic of); Seoul National University College of Medicine, Seoul National University Medical Research Center, Institute of Radiation Medicine, Bundang (Korea, Republic of); Kim, Kil Joong [Seoul National University College of Medicine, Department of Radiation Applied Life Science, Seoul (Korea, Republic of); Kim, Bohyoung; Lee, Hyunna [Seoul National University, School of Computer Science and Engineering, Seoul (Korea, Republic of); Park, Seong Ho [University of Ulsan College of Medicine, Department of Radiology and Research Institute of Radiology, Asan Medical Center, Seoul (Korea, Republic of); Yanof, Jeffrey H. [Philips Healthcare, CT Clinical Science, Cleveland, OH (United States); Hwang, Seung-sik [Inha University School of Medicine, Department of Social and Preventive Medicine, Incheon (Korea, Republic of)

    2011-02-15

    To determine whether the amount of tagged stool and fluid significantly affects the radiation exposure in low-dose screening CT colonography performed with an automatic tube-current modulation technique. The study included 311 patients. The tagging agent was barium (n = 271) or iodine (n = 40). Correlation was measured between mean volume CT dose index (CTDI{sub vol}) and the estimated x-ray attenuation of the tagged stool and fluid (ATT). Multiple linear regression analyses were performed to determine the effect of ATT on CTDI{sub vol} and the effect of ATT on image noise while adjusting for other variables including abdominal circumference. CTDI{sub vol} varied from 0.88 to 2.54 mGy. There was no significant correlation between CTDI{sub vol} and ATT (p = 0.61). ATT did not significantly affect CTDI{sub vol} (p = 0.93), while abdominal circumference was the only factor significantly affecting CTDI{sub vol} (p < 0.001). Image noise ranged from 59.5 to 64.1 HU. The p value for the regression model explaining the noise was 0.38. The amount of stool and fluid tagging does not significantly affect radiation exposure. (orig.)

  7. Does the amount of tagged stool and fluid significantly affect the radiation exposure in low-dose CT colonography performed with an automatic exposure control?

    International Nuclear Information System (INIS)

    Lim, Hyun Kyong; Lee, Kyoung Ho; Kim, So Yeon; Kim, Young Hoon; Kim, Kil Joong; Kim, Bohyoung; Lee, Hyunna; Park, Seong Ho; Yanof, Jeffrey H.; Hwang, Seung-sik

    2011-01-01

    To determine whether the amount of tagged stool and fluid significantly affects the radiation exposure in low-dose screening CT colonography performed with an automatic tube-current modulation technique. The study included 311 patients. The tagging agent was barium (n = 271) or iodine (n = 40). Correlation was measured between mean volume CT dose index (CTDI vol ) and the estimated x-ray attenuation of the tagged stool and fluid (ATT). Multiple linear regression analyses were performed to determine the effect of ATT on CTDI vol and the effect of ATT on image noise while adjusting for other variables including abdominal circumference. CTDI vol varied from 0.88 to 2.54 mGy. There was no significant correlation between CTDI vol and ATT (p = 0.61). ATT did not significantly affect CTDI vol (p = 0.93), while abdominal circumference was the only factor significantly affecting CTDI vol (p < 0.001). Image noise ranged from 59.5 to 64.1 HU. The p value for the regression model explaining the noise was 0.38. The amount of stool and fluid tagging does not significantly affect radiation exposure. (orig.)

  8. Anchoring cationic amphiphiles for nucleotide delivery: significance of DNA release from cationic liposomes for transfection.

    Science.gov (United States)

    Hirashima, Naohide; Minatani, Kazuhiro; Hattori, Yoshifumi; Ohwada, Tomohiko; Nakanishi, Mamoru

    2007-06-01

    We have designed and synthesized lithocholic acid-based cationic amphiphile molecules as components of cationic liposomes for gene transfection (lipofection). To study the relationship between the molecular structures of those amphiphilic molecules, particularly the extended hydrophobic appendant (anchor) at the 3-hydroxyl group, and transfection efficiency, we synthesized several lithocholic and isolithocholic acid derivatives, and examined their transfection efficiency. We also compared the physico-chemical properties of cationic liposomes prepared from these derivatives. We found that isolithocholic acid derivatives exhibit higher transfection efficiency than the corresponding lithocholic acid derivatives. This result indicates that the orientation and extension of hydrophobic regions influence the gene transfection process. Isolithocholic acid derivatives showed a high ability to encapsulate DNA in a compact liposome-DNA complex and to protect it from enzymatic degradation. Isolithocholic acid derivatives also facilitated the release of DNA from the liposome-DNA complex, which is a crucial step for DNA entry into the nucleus. Our results show that the transfection efficiency is directly influenced by the ability of the liposome complex to release DNA, rather than by the DNA-encapsulating ability. Molecular modeling revealed that isolithocholic acid derivatives take relatively extended conformations, while the lithocholic acid derivatives take folded structures. Thus, the efficiency of release of DNA from cationic liposomes in the cytoplasm, which contributes to high transfection efficiency, appears to be dependent upon the molecular shape of the cationic amphiphiles.

  9. Amount of platelet-bound IgG in chronic autoimmune thrombocytopenic purpura (ITP): absence of significant influence on platelet survival and destruction-site

    International Nuclear Information System (INIS)

    Leners, N.; Ferrant, A.; Beckers, C.

    1982-01-01

    The amount of platelet-bound IgG, as measured with a direct Coombs radioactive antiglobulin test, could not be correlated with either platelet survival or the site of platelet destruction in 22 patients with chronic ITP. The amount of platelet-bound IgG may not be an index of severity in this disease, nor does it offer an indication on the site of destruction of platelets

  10. The radiological significance of transuranium radioisotopes released to the environment during operation of the LMFBR fuel cycle

    International Nuclear Information System (INIS)

    Barr, N.F.

    1976-01-01

    Estimates based on current knowledge and conservative assumptions indicate that release of transuranium elements from the Liquid Metal Fast Breeder Reactor (LMFBR) fuel cycle are likely to proaduce population dose commitments small compared to those produced by naturally occurring alpha emitters and globally dispersed transuranium radioisotopes from tests of nuclear weapons in the atmosphere. Potential health consequences of these releases to current and future generations are estimated to be very small compared to risks associated with the production of energy by fossil fuels. The estimates are subject to a number of uncertainties imposed by lack of knowledge. Some of the uncertainties are not likely to be greatly reduced until LMFBR facilities are designed and operated. Others may be significantly reduced prior to facility design and operation. The paper discusses the sensitivity of the estimates to uncertainties and approches to reducing those uncertainties that strongly influence the estimates. (author)

  11. Inhibition of basophil histamine release by gangliosides. Further studies on the significance of cell membrane sialic acid in the histamine release process

    DEFF Research Database (Denmark)

    Jensen, C; Norn, S; Thastrup, Ole

    1987-01-01

    with the glucolipid mixture increased the sialic acid content of the cells, and this increase was attributed to an insertion of gangliosides into the cell membrane. The inhibition of histamine release was abolished by increasing the calcium concentration, which substantiates our previous findings that cell membrane......Histamine release from human basophils was inhibited by preincubation of the cells with a glucolipid mixture containing sialic acid-containing gangliosides. This was true for histamine release induced by anti-IgE, Concanavalin A and the calcium ionophore A23187, whereas the release induced by S....... aureus Wood 46 was not affected. It was demonstrated that the inhibitory capacity of the glucolipid mixture could be attributed to the content of gangliosides, since no inhibition was obtained with cerebrosides or with gangliosides from which sialic acid was removed. Preincubation of the cells...

  12. Dermal application of nitric oxide releasing acidified nitrite-containing liniments significantly reduces blood pressure in humans.

    Science.gov (United States)

    Opländer, Christian; Volkmar, Christine M; Paunel-Görgülü, Adnana; Fritsch, Thomas; van Faassen, Ernst E; Mürtz, Manfred; Grieb, Gerrit; Bozkurt, Ahmet; Hemmrich, Karsten; Windolf, Joachim; Suschek, Christoph V

    2012-02-15

    Vascular ischemic diseases, hypertension, and other systemic hemodynamic and vascular disorders may be the result of impaired bioavailability of nitric oxide (NO). NO but also its active derivates like nitrite or nitroso compounds are important effector and signal molecules with vasodilating properties. Our previous findings point to a therapeutical potential of cutaneous administration of NO in the treatment of systemic hemodynamic disorders. Unfortunately, no reliable data are available on the mechanisms, kinetics and biological responses of dermal application of nitric oxide in humans in vivo. The aim of the study was to close this gap and to explore the therapeutical potential of dermal nitric oxide application. We characterized with human skin in vitro and in vivo the capacity of NO, applied in a NO-releasing acidified form of nitrite-containing liniments, to penetrate the epidermis and to influence local as well as systemic hemodynamic parameters. We found that dermal application of NO led to a very rapid and significant transepidermal translocation of NO into the underlying tissue. Depending on the size of treated skin area, this translocation manifests itself through a significant systemic increase of the NO derivates nitrite and nitroso compounds, respectively. In parallel, this translocation was accompanied by an increased systemic vasodilatation and blood flow as well as reduced blood pressure. We here give evidence that in humans dermal application of NO has a therapeutic potential for systemic hemodynamic disorders that might arise from local or systemic insufficient availability of NO or its bio-active NO derivates, respectively. Copyright © 2012 Elsevier Inc. All rights reserved.

  13. Extended-release niacin/laropiprant significantly improves lipid levels in type 2 diabetes mellitus irrespective of baseline glycemic control

    Directory of Open Access Journals (Sweden)

    Bays HE

    2015-02-01

    Full Text Available Harold E Bays,1 Eliot A Brinton,2 Joseph Triscari,3 Erluo Chen,3 Darbie Maccubbin,3 Alexandra A MacLean,3 Kendra L Gibson,3 Rae Ann Ruck,3 Amy O Johnson-Levonas,3 Edward A O’Neill,3 Yale B Mitchel3 1Louisville Metabolic & Atherosclerosis Research Center (L-MARC, Louisville, KY, USA; 2Utah Foundation for Biomedical Research, Salt Lake City, UT, USA; 3Merck & Co, Inc., Whitehouse Station, NJ, USA Background: The degree of glycemic control in patients with type 2 diabetes mellitus (T2DM may alter lipid levels and may alter the efficacy of lipid-modifying agents. Objective: Evaluate the lipid-modifying efficacy of extended-release niacin/laropiprant (ERN/LRPT in subgroups of patients with T2DM with better or poorer glycemic control. Methods: Post hoc analysis of clinical trial data from patients with T2DM who were randomized 4:3 to double-blind ERN/LRPT or placebo (n=796, examining the lipid-modifying effects of ERN/LRPT in patients with glycosylated hemoglobin or fasting plasma glucose levels above and below median baseline levels. Results: At Week 12 of treatment, ERN/LRPT significantly improved low-density lipoprotein cholesterol, high-density lipoprotein cholesterol (HDL-C, non-high-density lipoprotein cholesterol, triglycerides, and lipoprotein (a, compared with placebo, with equal efficacy in patients above or below median baseline glycemic control. Compared with placebo, over 36 weeks of treatment more patients treated with ERN/LRPT had worsening of their diabetes and required intensification of antihyperglycemic medication, irrespective of baseline glycemic control. Incidences of other adverse experiences were generally low in all treatment groups. Conclusion: The lipid-modifying effects of ERN/LRPT are independent of the degree of baseline glycemic control in patients with T2DM (NCT00485758. Keywords: lipid-modifying agents, hyperglycemia, LDL, HDL, triglycerides

  14. Shear bond strengths of tooth coating materials including the experimental materials contained various amounts of multi-ion releasing fillers and their effects for preventing dentin demineralization.

    Science.gov (United States)

    Arita, Shoko; Suzuki, Masaya; Kazama-Koide, Miku; Shinkai, Koichi

    2017-10-01

    We examined shear bond strengths (SBSs) of various tooth-coating-materials including the experimental materials to dentin and demineralization resistance of a fractured adhesive surface after the SBS testing. Three resin-type tooth-coating-materials (BC, PRG Barrier Coat; HC, Hybrid Coat II; and SF, Shield force plus) and two glass-ionomer-type tooth-coating-materials (CV, Clinpro XT Varnish; and FJ, Fuji VII) were selected. The experimental PRG Barrier Coat containing 0, 17, and 33 wt% S-PRG filler (BC0, BC17, and BC33, respectively) were developed. Each tooth-coating-material was applied to flattened dentin surfaces of extracted human teeth for SBS testing. After storing in water for 32 days with 4000 thermal cycling, the specimens were subjected to the SBS test. Specimens after SBS testing were subjected to a pH cycling test, and then, demineralization depths were measured using a polarized-light microscope. ANOVA and Tukey's HSD test were used for statistical analysis. The SBS value of FJ and CV was significantly lower than those of other materials except for BC (p coating-materials demonstrated significantly higher SBS for dentin than the glass-ionomer-type tooth-coating-materials; however, they were inferior to the glass ionomer-type tooth-coating-materials in regards to the acid resistance of the fractured adhesion surface.

  15. Cetirizine release from cyclodextrin formulated compressed chewing gum

    DEFF Research Database (Denmark)

    Stojanov, Mladen; Larsen, Kim Lambertsen

    2012-01-01

    release patterns, but with variations in the total amount released. Chewing gum formulated with cetirizine alone, demonstrated a release of 75% after 8 min of chewing. The presence of CDs resulted in increased cetirizine release. The analysis of variance (ANOVA) demonstrated that parameters with the most...... the statistical analysis (ANOVA) demonstrated significance in the release (P

  16. Significant adverse reactions to long-acting gonadotropin-releasing hormone agonists for the treatment of central precocious puberty and early onset puberty

    Directory of Open Access Journals (Sweden)

    Ji Woo Lee

    2014-09-01

    Full Text Available PurposeLong-acting gonadotropin-releasing hormone agonists (GnRHa are commonly used to treat central precocious puberty (CPP in Korea. Although rare, there have been reports on the characteristic of adverse reactions of GnRHa in CPP among the Korean population. This study was intended to report on our clinical experience regarding significant adverse reactions to long-acting GnRHa in CPP and early onset puberty and to evaluate the prevalence rate of serious side effects.MethodsThis retrospective study included children with CPP and early onset puberty, who were administered monthly with long-acting GnRHa (leuprolide acetate, triptorelin acetate at the outpatient clinic of Department of Pediatrics, at Inha University Hospital, between January 2011 and December 2013. We analyzed the clinical characteristics of patients who experienced significant adverse reactions and evaluated the prevalence rate.ResultsSix serious side effects (0.9% were observed among total of 621 CPP and early onset puberty children with GnRHa therapy. The number of sterile abscess formation was four in three patients (4 events of 621. Anaphylaxis occurred in only one patient, and unilateral slipped capital femoral epiphysis (SCFE in another one patient. Anaphylaxis occurred after the 6th administration of the monthly depot triptorelin acetate. Unilateral SCFE developed in GnRHa therapy.ConclusionSterile abscess formation occurred in 0.6% of CPP and early onset puberty patients from the administration of a monthly depot GnRHa therapy. The occurrences of anaphylaxis and SCFE are extremely rare, but can have serious implications on patients. Clinicians should be aware of these potential adverse effects related to GnRHa therapy in CPP.

  17. [The changes of ghrelin, growth hormone, growth hormone releasing hormone and their clinical significances in patients with chronic obstructive pulmonary disease].

    Science.gov (United States)

    Xu, Zhi-song; Bao, Zi-yu; Wang, Zhi-ying; Yang, Guo-jun; Zhu, Dong-fang; Zhang, Li; Tan, Rong-mei

    2012-07-01

    To investigate the changes of plasma ghrelin, growth hormone (GH) and growth hormone releasing hormone (GHRH) and gastric ghrelin in patients with chronic obstructive pulmonary disease (COPD) and to explore their clinical significances. Plasma ghrelin, GH, GHRH, TNFα, IL-6 and C reactive protein (CRP) were measured in 40 COPD patients and 20 controls with chronic bronchitis. Correlated factors of plasma ghrelin, TNFα, IL-6, CRP were analyzed. Body composition was assessed with bioelectrical impedance analysis. The expression of gastric ghrelin in patients with COPD was detected. Plasma ghrelin was higher in the underweight patients than in the normal weight patients and in the controls [(1.78 ± 0.46) ng/L, (1.39 ± 0.46) ng/L, (1.36 ± 0.39) ng/L, respectively]. Plasma GH was lower in the underweight patients than in the normal weight patients and in the controls [(4.12 ± 0.83) µg/L, (5.17 ± 0.72)µg/L, (6.49 ± 1.13) µg/L, respectively]. Plasma GHRH was lower in the underweight patients than in the normal weight patients and in the controls [(20.43 ± 4.41) ng/L, (23.47 ± 3.97) ng/L, (27.48 ± 10.06) ng/L, respectively]. Plasma ghrelin was higher in the underweight patients than in the controls (P 0.05). Plasma ghrelin was positively correlated with TNFα and IL-6 in the underweight patients. The gastric expression of ghrelin showed no evident difference between the patients with COPD and the controls. The plasma GH in COPD patients may not be correlated with ghrelin. The plasma ghrelin level may be a useful indicator for malnutrition in COPD patients. Plasma ghrelin might be involved in the pathogenesis of CODP by affecting the body energy metabolism.

  18. Environmental significance of copper, lead, manganese, uranium and zinc speciation in the event of contaminated waters release from the Ranger Uranium Mining Complex

    International Nuclear Information System (INIS)

    Noller, B.N.; Currey, N.A.

    1983-01-01

    The likely impact of the accidental release of tailings dam water during the dry season at the Ranger Uranium Mining Complex was examined. A speciation scheme utilising sizing by filtration and ion-exchange with Chelex 100 has given an insight into the likely partitioning of zinc, copper, lead, manganese and uranium following the addition of tailings dam water to samples from waterbodies in the vicinity of the uranium mining/milling complex. The speciation findings are discussed in terms of likely toxic effects on fish

  19. A Case of Acromegaly in which a Pituitary Gland Tumor was Reduced Significantly by Administering Octreotide Long Acting Release (LAR) and Could Be Removed Surgically.

    Science.gov (United States)

    Arao, Tadashi; Okada, Yosuke; Uemura, Fumi; Nishizawa, Shigeru; Tanaka, Yoshiya

    A 54-year-old woman was admitted to our hospital for detailed examination of acromegaly because she noticed bilateral hand and finger swelling at the age of 43 and plantar thickening, facial changes and unclear articulation at the age of 49. She had prominent brow ridges, mandibular protrusion, and enlargement of the hands, feet, nasal wings, lips and tongue. Her growth hormone (GH) level was 39.8 ng/ml, insulin-like growth factor-1 (IGF-1) level was 717 ng/ml, GH level was not suppressed (22.9 ng/ml) during a 75-g oral glucose tolerance test (OGTT). Radiography showed cauliflower-like enlargement of the distal phalanx of the fingers, thickening/enlargement of the plantar soft tissues, and increased antero-posterior diameter of the sella turcica. Magnetic resonance imaging showed a mass (21×17 mm) growing towards the right suprasellar region and invading the cavernous sinus. She was diagnosed with acromegaly based on the characteristic physical findings, GH excess, high IGF-1, lack of GH suppression during the 75-g OGTT, and the presence of a pituitary tumor. She was started on octreotide long acting release (Oct-LAR) 20 mg/4w for tumor shrinkage. After three doses, her GH and IGF-1 levels decreased to 2.19 ng/ml (1.69 during the 75-g OGTT) and 205 ng/ml, respectively, meeting cure criteria for acromegaly. In this case, a decrease in GH and IGF-1 levels, tumor shrinkage, and resolution of cavernous sinus invasion allowed the patient to undergo surgery with curative intent (the first-line treatment for acromegaly) without postoperative complications. Thus, preoperative Oct-LAR administration has the potential to improve treatment outcomes of acromegaly.

  20. Methane release

    International Nuclear Information System (INIS)

    Seifert, M.

    1999-01-01

    The Swiss Gas Industry has carried out a systematic, technical estimate of methane release from the complete supply chain from production to consumption for the years 1992/1993. The result of this survey provided a conservative value, amounting to 0.9% of the Swiss domestic output. A continuation of the study taking into account new findings with regard to emission factors and the effect of the climate is now available, which provides a value of 0.8% for the target year of 1996. These results show that the renovation of the network has brought about lower losses in the local gas supplies, particularly for the grey cast iron pipelines. (author)

  1. Environmental Release Prevention and Control Plan

    International Nuclear Information System (INIS)

    Mamatey, A.; Arnett, M.

    1997-01-01

    During the history of SRS, continual improvements in facilities, process, and operations, and changes in the site''s mission have reduced the amount of radioactive liquid releases. In the early years of SRS (1958 to 1965), the amount of tritium discharged to the Savannah River averaged approximately 61,000 curies a year. During the mid-1980''s (1983 to 1988), liquid releases of tritium averaged 27,000 curies a year. By 1996, liquid releases of tritium are projected to be just 3000 curies for the year. This large projected decrease is the result of the planned shut-down of all reactors and the anticipated significant decline in the amount of tritium migrating from the site seepage basins and the Solid Waste Disposal Facility

  2. A simple assessment scheme for severe accident consequences using release parameters

    Energy Technology Data Exchange (ETDEWEB)

    Silva, Kampanart, E-mail: kampanarts@tint.or.th [Thailand Institute of Nuclear Technology, 16 Vibhavadi-Rangsit Rd., Latyao, Chatuchak, 10900 (Thailand); Okamoto, Koji [The University of Tokyo, 7-3-1 Hongo, Bunkyo, Tokyo 113-8654 (Japan)

    2016-08-15

    Highlights: • Nuclear accident consequence index can assess overall consequences of an accident. • Correlations between the index and release parameters are developed. • Relation between the index and release amount follows power function. • The exponent of the power function is the key to the relation. - Abstract: Nuclear accident consequence index (NACI) which can assess the overall consequences of a severe accident on people and the environment is developed based on findings from previous studies. It consists of three indices: radiation effect index, relocation index and decontamination index. Though the NACI can cover large range of consequences, its assessment requires extensive resources. The authors then attempt to simplify the assessment, by investigating the relations between the release parameters and the NACI, in order to use the release parameters for severe accident consequence assessment instead of the NACI. NACI and its components increase significantly when the release amount is increased, while the influences of the release period and the release starting time on the NACI are nearly negligible. Relations between the release amount and the NACI and its components follow simple power functions (y = ax{sup b}). The exponent of the power functions seems to be the key to the relations. The exponent of the relation between the release amount and the NACI was around 0.8–1.0 when the release amount is smaller than 100 TBq, and it increased to around 1.3–1.4 when the release amount is equal to or larger than 100 TBq.

  3. Simulated food effects on drug release from ethylcellulose: PVA-PEG graft copolymer-coated pellets.

    Science.gov (United States)

    Muschert, Susanne; Siepmann, Florence; Leclercq, Bruno; Carlin, Brian; Siepmann, Juergen

    2010-02-01

    Food effects might substantially alter drug release from oral controlled release dosage forms in vivo. The robustness of a novel type of controlled release film coating was investigated using various types of release media and two types of release apparatii. Importantly, none of the investigated conditions had a noteworthy impact on the release of freely water-soluble diltiazem HCl or slightly water-soluble theophylline from pellets coated with ethylcellulose containing small amounts of PVA-PEG graft copolymer. In particular, the presence of significant amounts of fats, carbohydrates, surfactants, bile salts, and calcium ions in the release medium did not alter drug release. Furthermore, changes in the pH and differences in the mechanical stress the dosage forms were exposed to did not affect drug release from the pellets. The investigated film coatings allowing for oral controlled drug delivery are highly robust in vitro and likely to be poorly sensitive to classical food effects in vivo.

  4. Fluoride and sodium trimetaphosphate (TMP release from fluoride varnishes supplemented with TMP

    Directory of Open Access Journals (Sweden)

    Michele Mauricio MANARELLI

    2016-01-01

    Full Text Available Abstract This study assessed fluoride (F and sodium trimetaphosphate (TMP release into artificial saliva from varnishes containing 0%, 2.5%, and 5% NaF, supplemented or not with 5% TMP. The varnishes were applied on polyester sheets (n = 8/group, and F and TMP released into artificial saliva were measured for up to 24 hours. The amount of F and TMP released were directly related to NaF and TMP concentrations in the varnishes. The highest F release was seen for 5% NaF and 5% NaF + 5% TMP, whereas 5% TMP released the highest amount of TMP. However, the simultaneous addition of NaF and TMP to varnishes significantly reduced the amount of F and TMP released from the products.

  5. Cell-swelling-induced taurine release from isolated perfused rat liver

    NARCIS (Netherlands)

    Brand, H. S.; Meijer, A. J.; Gustafson, L. A.; Jörning, G. G.; Leegwater, A. C.; Maas, M. A.; Chamuleau, R. A.

    1994-01-01

    Astrocytes and lymphocytes are able to release significant amounts of taurine during periods of hypotonicity to reduce the increase in cell volume. To investigate this mechanism in the liver, we studied the release of free amino acids from isolated perfused rat liver during hypotonicity. The

  6. Physician Fee Schedule National Payment Amount File

    Data.gov (United States)

    U.S. Department of Health & Human Services — The significant size of the Physician Fee Schedule Payment Amount File-National requires that database programs (e.g., Access, dBase, FoxPro, etc.) be used to read...

  7. Subtype-specific suppression of Shiga toxin 2 released from Escherichia coli upon exposure to protein synthesis inhibitors

    DEFF Research Database (Denmark)

    Pedersen, Malene Gantzhorn; Hansen, Claus; Riise, Erik

    2008-01-01

    Shiga toxins (Stx) are important virulence factors in the pathogenesis of severe disease including hemolytic-uremic syndrome, caused by Stx-producing Escherichia coli (STEC). STEC strains increase the release of Stx in vitro following the addition of fluoroquinolones, whereas protein synthesis...... inhibitors previously have been reported to suppress the release of Stx. The amount of Stx released from wild-type STEC strains incubated with protein synthesis inhibitors was examined by a Vero cell cytotoxicity assay. The amounts released were compared to the Stx type (Stx1 or Stx2) and additionally...... to the individual subtypes and toxin variants of Stx2. In general, Stx2 release was suppressed significantly upon exposure to protein synthesis inhibitors at MICs, which was not observed in the case of Stx1. Also, the average amount of different Stx2 toxin variants released was suppressed to various levels ranging...

  8. Effect of Food Emulsifiers on Aroma Release

    Directory of Open Access Journals (Sweden)

    Jia-Jia Li

    2016-04-01

    Full Text Available This study aimed to determine the influence of different emulsifiers or xanthan-emulsifier systems on the release of aroma compounds. Solid-phase microextraction (SPME and GC-MS were used to study the effects of varying concentrations of xanthan gum, sucrose fatty acid ester, Tween 80 and soybean lecithin on the release of seven aroma compounds. The effects of the emulsifier systems supplemented with xanthan gum on aroma release were also studied in the same way. The results showed varying degrees of influence of sucrose fatty acid ester, soybean lecithin, Tween 80 and xanthan gum on the release of aroma compounds. Compared with other aroma compounds, ethyl acetate was more likely to be conserved in the solution system, while the amount of limonene released was the highest among these seven aroma compounds. In conclusion, different emulsifiers and complexes showed different surface properties that tend to interact with different aroma molecules. The present studies showed that the composition and structure of emulsifiers and specific interactions between emulsifiers and aroma molecules have significant effects on aroma release.

  9. Influence of environmental factors on mercury release in hydroelectric reservoirs

    Energy Technology Data Exchange (ETDEWEB)

    Morrison, K.; Therien, N.

    1991-04-01

    Due to increased mercury concentrations in fish in hydro-electric reservoirs after flooding, a study was carried out to evaluate the release and transformation of mercury due to vegetation and soil flooded as a result of reservoir creation. Samples of vegetation and soils were immersed in water and concentrations of total mercury, methylmercury and nutrients were followed. The effects of anoxia, pH and temperature on release and transformation were examined. An existing dynamic model of decomposition of flooded materials in reservoirs was modified to include mercury release and transformation, and was calibrated to the experimental data. Amounts of mercury released by the different substrates was of the same order of magnitude. Tree species contributed to the greatest amounts of methylmercury per unit biomass, but the biomass used for these was twigs and foliage. Soil released significant amounts of mercury, but methylation was very low. The model was able to fit well for all substrates except lichen. The model can be adapted to proposed reservoirs to predict nutrient and mecury release and transformation. 175 refs., 38 figs., 38 tabs.

  10. Slow-release fertilizer

    Science.gov (United States)

    Ming, Douglas W.; Golden, D. C.

    1992-10-01

    A synthetic apatite containing agronutrients and a method for making the apatite are disclosed. The apatite comprises crystalline calcium phosphate having agronutrients dispersed in the crystalline structure. The agronutrients can comprise potassium, magnesium, sulfur, iron, manganese, molybdenum, chlorine, boron, copper and zinc in amounts suited for plant growth. The apatite can optionally comprise a carbonate and/or silicon solubility control agent. The agronutrients are released slowly as the apatite dissolves.

  11. Slow-release fertilizer

    Science.gov (United States)

    Ming, Douglas W. (Inventor); Golden, Dadigamuwage C. (Inventor)

    1995-01-01

    A synthetic apatite containing agronutrients and a method for making the apatite are disclosed. The apatite comprises crystalline calcium phosphate having agronutrients dispersed in the crystalline structure. The agronutrients can comprise potassium, magnesium, sulfur, iron, manganese, molybdenum, chlorine, boron, copper and zinc in amounts suited for plant growth. The apatite can optionally comprise a carbonate and/or silicon solubility control agent. The agronutrients are released slowly as the apatite dissolves.

  12. Profile of Fluoride Release from a Nanohybrid Composite Resin

    Directory of Open Access Journals (Sweden)

    Raquel Assed Bezerra Silva

    2015-02-01

    Full Text Available The aim of this study was to evaluate in vitro the amount and profile of fluoride release from a fluoride-containing nanohybrid composite resin (Tetric® N-Ceram by direct potentiometry. Thirty specimens (5 mm diameter x 3 mm high; n=10/material were made of Tetric® N-Ceram, Vitremer® resin-modified glass ionomer cement (RMGIC (positive control or Filtek® Z350 nanofill composite resin (negative control. The specimens were stored individually in plastic tubes containing 1 mL of artificial saliva at 37°C, which was daily renewed during 15 days. At each renewal of saliva, the amount of fluoride ions released in the solution was measured using a fluoride ion-selective electrode with ion analyzer, and the values obtained in mV were converted to ppm (µg/mL. Data were analyzed statistically by ANOVA and Tukey’s post-hoc test at a significance level of 5%. The results showed that the resins Tetric® N-Ceram and Filtek® Z350 did not release significant amounts of fluoride during the whole period of evaluation (p>0.05. Only Vitremer® released significant amounts of fluoride ions during the 15 days of the experiment, with greater release in first 2 days (p0.05. In conclusion, the nanohybrid composite resin Tetric® N-Ceram did not present in vitro fluoride-releasing capacity throughout the 15 days of study.

  13. Release of Hormones from Conjugates: Chloroplast Expression of β-Glucosidase Results in Elevated Phytohormone Levels Associated with Significant Increase in Biomass and Protection from Aphids or Whiteflies Conferred by Sucrose Esters1[C][OA

    Science.gov (United States)

    Jin, Shuangxia; Kanagaraj, Anderson; Verma, Dheeraj; Lange, Theo; Daniell, Henry

    2011-01-01

    Transplastomic tobacco (Nicotiana tabacum) plants expressing β-glucosidase (Bgl-1) show modified development. They flower 1 month earlier with an increase in biomass (1.9-fold), height (1.5-fold), and leaf area (1.6-fold) than untransformed plants. Trichome density on the upper and lower leaf surfaces of BGL-1 plants increase by 10- and 7-fold, respectively, harboring 5-fold more glandular trichomes (as determined by rhodamine B staining), suggesting that BGL-1 lines produce more sugar esters than control plants. Gibberellin (GA) levels were investigated because it is a known regulator of flowering time, plant height, and trichome development. Both GA1 and GA4 levels are 2-fold higher in BGL-1 leaves than in untransformed plants but do not increase in other organs. In addition, elevated levels of other plant hormones, including zeatin and indole-3-acetic acid, are observed in BGL-1 lines. Protoplasts from BGL-1 lines divide and form calli without exogenous hormones. Cell division in protoplasts is enhanced 7-fold in the presence of exogenously applied zeatin-O-glucoside conjugate, indicating the release of active hormones from their conjugates. Whitefly (Bemisia tabaci) and aphid (Myzus persicae) populations in control plants are 18 and 15 times higher than in transplastomic lines, respectively. Lethal dose to kill 50% of the test population values of 26.3 and 39.2 μg per whitefly and 23.1 and 35.2 μg per aphid for BGL-1 and untransformed control exudates, respectively, confirm the enhanced toxicity of transplastomic exudates. These data indicate that increase in sugar ester levels in BGL-1 lines might function as an effective biopesticide. This study provides a novel strategy for designing plants for enhanced biomass production and insect control by releasing plant hormones or sugar esters from their conjugates stored within their chloroplasts. PMID:21068365

  14. Release of hormones from conjugates: chloroplast expression of β-glucosidase results in elevated phytohormone levels associated with significant increase in biomass and protection from aphids or whiteflies conferred by sucrose esters.

    Science.gov (United States)

    Jin, Shuangxia; Kanagaraj, Anderson; Verma, Dheeraj; Lange, Theo; Daniell, Henry

    2011-01-01

    Transplastomic tobacco (Nicotiana tabacum) plants expressing β-glucosidase (Bgl-1) show modified development. They flower 1 month earlier with an increase in biomass (1.9-fold), height (1.5-fold), and leaf area (1.6-fold) than untransformed plants. Trichome density on the upper and lower leaf surfaces of BGL-1 plants increase by 10- and 7-fold, respectively, harboring 5-fold more glandular trichomes (as determined by rhodamine B staining), suggesting that BGL-1 lines produce more sugar esters than control plants. Gibberellin (GA) levels were investigated because it is a known regulator of flowering time, plant height, and trichome development. Both GA(1) and GA(4) levels are 2-fold higher in BGL-1 leaves than in untransformed plants but do not increase in other organs. In addition, elevated levels of other plant hormones, including zeatin and indole-3-acetic acid, are observed in BGL-1 lines. Protoplasts from BGL-1 lines divide and form calli without exogenous hormones. Cell division in protoplasts is enhanced 7-fold in the presence of exogenously applied zeatin-O-glucoside conjugate, indicating the release of active hormones from their conjugates. Whitefly (Bemisia tabaci) and aphid (Myzus persicae) populations in control plants are 18 and 15 times higher than in transplastomic lines, respectively. Lethal dose to kill 50% of the test population values of 26.3 and 39.2 μg per whitefly and 23.1 and 35.2 μg per aphid for BGL-1 and untransformed control exudates, respectively, confirm the enhanced toxicity of transplastomic exudates. These data indicate that increase in sugar ester levels in BGL-1 lines might function as an effective biopesticide. This study provides a novel strategy for designing plants for enhanced biomass production and insect control by releasing plant hormones or sugar esters from their conjugates stored within their chloroplasts.

  15. Chlorine release from biomass. Part 6; Kloravgaang fraan biobraenslen. Del 6

    Energy Technology Data Exchange (ETDEWEB)

    Zintl, Frank; Stroemberg, Birgitta [TPS Termiska Processer AB, Nykoeping (Sweden)

    2000-04-01

    Chlorine release from model compounds and different biomass fuels has been studied during thermal treatment in an electric oven in inert atmosphere (N{sub 2}) and with addition of 10% O{sub 2}. The amount of chlorine in all investigated materials has been kept to 2% with addition of KCl solution in methanol. The amount of chlorine was analysed before and after treatment in the decided atmosphere and to the temperature chosen. The influence from different functional groups on the chlorine release at low temperatures has been studied in pyrolysis experiments of simple model compounds with different structures. A good correlation between the chlorine release and the functional groups in the model substances was achieved. Results from the experiments shows that the early chlorine release, is most likely to occur in all biofuels, since all biomass fuels contains biological material with significant amounts of functional groups which can interact with fuel chlorine ( inorganic chlorine)

  16. Controlled release system for ametryn using polymer microspheres: Preparation, characterization and release kinetics in water

    International Nuclear Information System (INIS)

    Grillo, Renato; Pereira, Anderson do Espirito Santo; Ferreira Silva de Melo, Nathalie; Porto, Raquel Martins; Feitosa, Leandro Oliveira; Tonello, Paulo Sergio; Dias Filho, Newton L.; Rosa, Andre Henrique; Lima, Renata; Fraceto, Leonardo Fernandes

    2011-01-01

    The purpose of this work was to develop a modified release system for the herbicide ametryn by encapsulating the active substance in biodegradable polymer microparticles produced using the polymers poly(hydroxybutyrate) (PHB) or poly(hydroxybutyrate-valerate) (PHBV), in order to both improve the herbicidal action and reduce environmental toxicity. PHB or PHBV microparticles containing ametryn were prepared and the efficiencies of herbicide association and loading were evaluated, presenting similar values of approximately 40%. The microparticles were characterized by scanning electron microscopy (SEM), which showed that the average sizes of the PHB and PHBV microparticles were 5.92 ± 0.74 μm and 5.63 ± 0.68 μm, respectively. The ametryn release profile was modified when it was encapsulated in the microparticles, with slower and more sustained release compared to the release profile of pure ametryn. When ametryn was associated with the PHB and PHBV microparticles, the amount of herbicide released in the same period of time was significantly reduced, declining to 75% and 87%, respectively. For both types of microparticle (PHB and PHBV) the release of ametryn was by diffusion processes due to anomalous transport (governed by diffusion and relaxation of the polymer chains), which did not follow Fick's laws of diffusion. The results presented in this paper are promising, in view of the successful encapsulation of ametryn in PHB or PHBV polymer microparticles, and indications that this system may help reduce the impacts caused by the herbicide, making it an environmentally safer alternative.

  17. Statistical Optimization of Sustained Release Venlafaxine HCI Wax Matrix Tablet.

    Science.gov (United States)

    Bhalekar, M R; Madgulkar, A R; Sheladiya, D D; Kshirsagar, S J; Wable, N D; Desale, S S

    2008-01-01

    The purpose of this research was to prepare a sustained release drug delivery system of venlafaxine hydrochloride by using a wax matrix system. The effects of bees wax and carnauba wax on drug release profile was investigated. A 3(2) full factorial design was applied to systemically optimize the drug release profile. Amounts of carnauba wax (X(1)) and bees wax (X(2)) were selected as independent variables and release after 12 h and time required for 50% (t(50)) drug release were selected as dependent variables. A mathematical model was generated for each response parameter. Both waxes retarded release after 12 h and increases the t(50) but bees wax showed significant influence. The drug release pattern for all the formulation combinations was found to be approaching Peppas kinetic model. Suitable combination of two waxes provided fairly good regulated release profile. The response surfaces and contour plots for each response parameter are presented for further interpretation of the results. The optimum formulations were chosen and their predicted results found to be in close agreement with experimental findings.

  18. Significant event of patient radiation protection in radiotherapy (criterion 2.1): declaration and rating on the ASN-SFRO scale - ASN guide nr 16 - Release of the 01/01/2010

    International Nuclear Information System (INIS)

    2010-01-01

    This document brings together all the tools for the management of a significant event in radiation protection concerning a patient in radiotherapy. It contains the declaration form, a model for the reporting of significant events, and the ASN-SFRO scale which allows the event to be rated. After a presentation of the regulatory context and references, of the scope of application, this guide addresses the declaration of a significant event: general principles, definition of the 2.1 criterion, examples, delays and modalities of declaration, addressees of a declaration. It addresses the reporting of a significant event: general principles, sending delays and modalities. It addresses the rating on the ASN-SFRO scale: general principles, scale, and rating process. The last part deals with public information

  19. Significant event of patient radiation protection in radiotherapy (criterion 2.1): declaration and rating on the ASN-SFRO scale - ASN guide no. 16 - Release of 17/07/2015

    International Nuclear Information System (INIS)

    2015-01-01

    This document is an update of the previous version from October 2010. It brings together all the tools for the management of a significant event in radiation protection concerning a patient in radiotherapy. It contains the declaration form, a model for the reporting of significant events, and the ASN-SFRO scale which allows the event to be rated. After a presentation of the regulatory context and references, of the scope of application, this guide addresses the declaration of a significant event: general principles, definition of the 2.1 criterion, examples, delays and modalities of declaration, addressees of a declaration. It addresses the reporting of a significant event: general principles, sending delays and modalities. It addresses the rating on the ASN-SFRO scale: general principles, scale, and rating process. The last part deals with public information

  20. The 2017 Release Cloudy

    Science.gov (United States)

    Ferland, G. J.; Chatzikos, M.; Guzmán, F.; Lykins, M. L.; van Hoof, P. A. M.; Williams, R. J. R.; Abel, N. P.; Badnell, N. R.; Keenan, F. P.; Porter, R. L.; Stancil, P. C.

    2017-10-01

    We describe the 2017 release of the spectral synthesis code Cloudy, summarizing the many improvements to the scope and accuracy of the physics which have been made since the previous release. Exporting the atomic data into external data files has enabled many new large datasets to be incorporated into the code. The use of the complete datasets is not realistic for most calculations, so we describe the limited subset of data used by default, which predicts significantly more lines than the previous release of Cloudy. This version is nevertheless faster than the previous release, as a result of code optimizations. We give examples of the accuracy limits using small models, and the performance requirements of large complete models. We summarize several advances in the H- and He-like iso-electronic sequences and use our complete collisional-radiative models to establish the densities where the coronal and local thermodynamic equilibrium approximations work.

  1. Decontamination for free release

    Energy Technology Data Exchange (ETDEWEB)

    Simpson, K A; Elder, G R [Bradtec Ltd., Bristol (United Kingdom)

    1997-02-01

    Many countries are seeking to treat radioactive waste in ways which meet the local regulatory requirements, but yet are cost effective when all contributing factors are assessed. In some countries there are increasing amounts of waste, arising from nuclear plant decommissioning, which are categorized as low level waste: however with suitable treatment a large part of such wastes might become beyond regulatory control and be able to be released as non-radioactive. The benefits and disadvantages of additional treatment before disposal need to be considered. Several processes falling within the overall description of decontamination for free release have been developed and applied, and these are outlined. In one instance the process seeks to take advantage of techniques and equipment used for decontaminating water reactor circuits intermittently through reactor life. (author). 9 refs, 1 fig., 3 tabs.

  2. Influence of Citric Acid on the Metal Release of Stainless Steels

    Energy Technology Data Exchange (ETDEWEB)

    Mazinanian, N.; Wallinder, I. Odnevall; Hedberg, Y. S. [KTH Royal Institute of Technology, School of Chemical Science and Engineering, Department of Chemistry, Division of Surface and Corrosion Science, Stockholm (Sweden)

    2015-08-15

    Knowledge of how metal releases from the stainless steels used in food processing applications and cooking utensils is essential within the framework of human health risk assessment. A new European standard test protocol for testing metal release in food contact materials made from metals and alloys has recently been published by the Council of Europe. The major difference from earlier test protocols is the use of citric acid as the worst-case food simulant. The objectives of this study were to assess the effect of citric acid at acidic, neutral, and alkaline solution pH on the extent of metal release for stainless steel grades AISI 304 and 316, commonly used as food contact materials. Both grades released lower amounts of metals than the specific release limits when they were tested according to test guidelines. The released amounts of metals were assessed by means of graphite furnace atomic absorption spectroscopy, and changes in the outermost surface composition were determined using X-ray photoelectron spectroscopy. The results demonstrate that both the pH and the complexation capacity of the solutions affected the extent of metal release from stainless steel and are discussed from a mechanistic perspective. The outermost surface oxide was significantly enriched in chromium upon exposure to citric acid, indicating rapid passivation by the acid. This study elucidates the effect of several possible mechanisms, including complex ion- and ligand-induced metal release, that govern the process of metal release from stainless steel under passive conditions in solutions that contain citric acid.

  3. COMMERCIAL SNF ACCIDENT RELEASE FRACTIONS

    Energy Technology Data Exchange (ETDEWEB)

    S.O. Bader

    1999-10-18

    The purpose of this design analysis is to specify and document the total and respirable fractions for radioactive materials that are released from an accident event at the Monitored Geologic Repository (MGR) involving commercial spent nuclear fuel (CSNF) in a dry environment. The total and respirable release fractions will be used to support the preclosure licensing basis for the MGR. The total release fraction is defined as the fraction of total CSNF assembly inventory, typically expressed as an activity inventory (e.g., curies), of a given radionuclide that is released to the environment from a waste form. The radionuclides are released from the inside of breached fuel rods (or pins) and from the detachment of radioactive material (crud) from the outside surfaces of fuel rods and other components of fuel assemblies. The total release fraction accounts for several mechanisms that tend to retain, retard, or diminish the amount of radionuclides that are available for transport to dose receptors or otherwise can be shown to reduce exposure of receptors to radiological releases. The total release fraction includes a fraction of airborne material that is respirable and could result in inhalation doses. This subset of the total release fraction is referred to as the respirable release fraction. Potential accidents may involve waste forms that are characterized as either bare (unconfined) fuel assemblies or confined fuel assemblies. The confined CSNF assemblies at the MGR are contained in shipping casks, canisters, or disposal containers (waste packages). In contrast to the bare fuel assemblies, the container that confines the fuel assemblies has the potential of providing an additional barrier for diminishing the total release fraction should the fuel rod cladding breach during an accident. However, this analysis will not take credit for this additional bamer and will establish only the total release fractions for bare unconfined CSNF assemblies, which may however be

  4. COMMERCIAL SNF ACCIDENT RELEASE FRACTIONS

    International Nuclear Information System (INIS)

    S.O. Bader

    1999-01-01

    The purpose of this design analysis is to specify and document the total and respirable fractions for radioactive materials that are released from an accident event at the Monitored Geologic Repository (MGR) involving commercial spent nuclear fuel (CSNF) in a dry environment. The total and respirable release fractions will be used to support the preclosure licensing basis for the MGR. The total release fraction is defined as the fraction of total CSNF assembly inventory, typically expressed as an activity inventory (e.g., curies), of a given radionuclide that is released to the environment from a waste form. The radionuclides are released from the inside of breached fuel rods (or pins) and from the detachment of radioactive material (crud) from the outside surfaces of fuel rods and other components of fuel assemblies. The total release fraction accounts for several mechanisms that tend to retain, retard, or diminish the amount of radionuclides that are available for transport to dose receptors or otherwise can be shown to reduce exposure of receptors to radiological releases. The total release fraction includes a fraction of airborne material that is respirable and could result in inhalation doses. This subset of the total release fraction is referred to as the respirable release fraction. Potential accidents may involve waste forms that are characterized as either bare (unconfined) fuel assemblies or confined fuel assemblies. The confined CSNF assemblies at the MGR are contained in shipping casks, canisters, or disposal containers (waste packages). In contrast to the bare fuel assemblies, the container that confines the fuel assemblies has the potential of providing an additional barrier for diminishing the total release fraction should the fuel rod cladding breach during an accident. However, this analysis will not take credit for this additional bamer and will establish only the total release fractions for bare unconfined CSNF assemblies, which may however be

  5. Modulation of drug release kinetics of shellac-based matrix tablets by in-situ polymerization through annealing process.

    Science.gov (United States)

    Limmatvapirat, Sontaya; Limmatvapirat, Chutima; Puttipipatkhachorn, Satit; Nunthanid, Jurairat; Luangtana-anan, Manee; Sriamornsak, Pornsak

    2008-08-01

    A new oral-controlled release matrix tablet based on shellac polymer was designed and developed, using metronidazole (MZ) as a model drug. The shellac-based matrix tablets were prepared by wet granulation using different amounts of shellac and lactose. The effect of annealing temperature and pH of medium on drug release from matrix tablets was investigated. The increased amount of shellac and increased annealing temperature significantly affected the physical properties (i.e., tablet hardness and tablet disintegration) and MZ release from the matrix tablets. The in-situ polymerization played a major role on the changes in shellac properties during annealing process. Though the shellac did not dissolve in acid medium, the MZ release in 0.1N HCl was faster than in pH 7.3 buffer, resulting from a higher solubility of MZ in acid medium. The modulation of MZ release kinetics from shellac-based matrix tablets could be accomplished by varying the amount of shellac or annealing temperature. The release kinetics was shifted from relaxation-controlled release to diffusion-controlled release when the amount of shellac or the annealing temperature was increased.

  6. Comparative evaluation of metal ions release from titanium and Ti-6Al-7Nb into bio-fluids

    Directory of Open Access Journals (Sweden)

    Lori A Joseph

    2009-01-01

    Full Text Available Background: The study was designed to investigate the effects of pH, chloride ions and nature of some bio-fluids on the amount of metal ions released from titanium and TiAl 6 Nb 7 plates following incubation in actual and simulated bio-fluids over time. Methods: The amounts of released metal ions from commercially pure titanium (CpTi and TiAl 6 Nb 7 of surgical grade on immersion in 20 mL Hank′s solution of pH 4.0 or 7.0, Hank′s solution of high chloride ions concentration, Whole Blood Serum (WBS and Phosphate Buffered Saline (PBS at 37° C were determined over an incubation time of 20 weeks using atomic absorption spectrophotometry. The levels of released metal ions were compared by two-way ANOVA and Duncan′s post-hoc tests. The amounts of titanium ions released by the samples were analyzed by Pearson′s correlation. Results: TiAl 6 Nb 7 plate showed no release of Ti ions into the test solutions until after 12 weeks of incubation, while Ti ions were released from the CpTi plate from the 1 day immersion time. The re-lease of measurable amount of Al ions from TiAl 6 Nb 7 was after 12 weeks of incubation. The rate of release of Ti and Al ions from the samples increased initially with incubation time and then stabilized due to adsorption-desorption equilibrium. Conclusion: The results showed that variations in pH and chloride ions of the test media has a sig-nificant effect on the amounts of Ti ions released, while increase in chloride ions concentration sig-nificantly elevates the release of Al ions into the bio-fluids.

  7. 46 CFR 308.403 - Insured amounts.

    Science.gov (United States)

    2010-10-01

    ... total amount of war risk insurance obtainable from companies authorized to do an insurance business in a... MARITIME ADMINISTRATION, DEPARTMENT OF TRANSPORTATION EMERGENCY OPERATIONS WAR RISK INSURANCE War Risk Builder's Risk Insurance § 308.403 Insured amounts. (a) Prelaunching period. The amount insured during...

  8. 13 CFR 400.202 - Loan amount.

    Science.gov (United States)

    2010-01-01

    ... 13 Business Credit and Assistance 1 2010-01-01 2010-01-01 false Loan amount. 400.202 Section 400.202 Business Credit and Assistance EMERGENCY STEEL GUARANTEE LOAN BOARD EMERGENCY STEEL GUARANTEE LOAN PROGRAM Steel Guarantee Loans § 400.202 Loan amount. (a) The aggregate amount of loan principal guaranteed...

  9. 13 CFR 500.202 - Loan amount.

    Science.gov (United States)

    2010-01-01

    ... 13 Business Credit and Assistance 1 2010-01-01 2010-01-01 false Loan amount. 500.202 Section 500.202 Business Credit and Assistance EMERGENCY OIL AND GAS GUARANTEED LOAN BOARD EMERGENCY OIL AND GAS GUARANTEED LOAN PROGRAM Oil and Gas Guaranteed Loans § 500.202 Loan amount. The aggregate amount of loan...

  10. 45 CFR 32.8 - Amounts withheld.

    Science.gov (United States)

    2010-10-01

    ...) of this section, or (ii) An amount equal to 25% of the debtor's disposable pay less the amount(s... first pay day after the employer receives the order. However, if the first pay day is within 10 days after receipt of the order, the employer may begin deductions on the second pay day. (k) An employer may...

  11. 31 CFR 235.5 - Reclamation amounts.

    Science.gov (United States)

    2010-07-01

    ... 31 Money and Finance: Treasury 2 2010-07-01 2010-07-01 false Reclamation amounts. 235.5 Section 235.5 Money and Finance: Treasury Regulations Relating to Money and Finance (Continued) FISCAL SERVICE... ON DESIGNATED DEPOSITARIES § 235.5 Reclamation amounts. Amounts received by way of reclamation on...

  12. Release of metal ions from round and rectangular NiTi wires

    Directory of Open Access Journals (Sweden)

    Arash Azizi

    2016-04-01

    Full Text Available Abstract Background The aim of this study was to evaluate the amount of nickel and titanium ions released from two wires with different shapes and a similar surface area. Methods Forty round nickel-titanium (NiTi arch wires with the diameter of 0.020 in. and 40 rectangular NiTi arch wires with the diameter of 0.016 × 0.016 in. were immersed in artificial saliva during a 21-day period. The surface area of both wires was 0.44 in.2. Wires were separately dipped into polypropylene tubes containing 50 ml of buffer solution and were incubated and maintained at 37 °C. Inductively coupled plasma atomic emission spectrometry (ICP-AES was used to measure the amount of ions released after exposure lengths of 1 h, 24 h, 1 week, and 3 weeks. Repeated measures ANOVA and Tukey tests were used to evaluate the data. Results The results indicated that the amount of nickel and titanium concentrations was significantly higher in the rectangular wire group. The most significant release of all metals was measured after the first hour of immersion. In the rectangular wire group, 243 ± 4.2 ng/ml of nickel was released after 1 h, while 221.4 ± 1.7 ng/ml of nickel was released in the round wire group. Similarly, 243.3 ± 2.8 ng/ml of titanium was released in the rectangular wire group and a significantly lower amount of 211.9 ± 2.3 ng/ml of titanium was released in the round wire group. Conclusions Release of metal ions was influenced by the shape of the wire and increase of time.

  13. Sustained release of radioprotective agents

    International Nuclear Information System (INIS)

    Shani, J.

    1980-11-01

    New pharmaceutical formulations for the sustained release into the G.I. tract of radioprotective agents have been developed by the authors. The experimental method initially consisted in the production of methylcellulose microcapsules. This method failed apparently because of the premature ''explosion'' of the microcapsules and the consequent premature release of massive amounts of the drug. A new method has been developed which consists in drying and pulverising cysteamine and cysteine preparations, mixing them in various proportions with stearic acid and ethylcellulose as carriers. The mixture is then compressed into cylindrical tablets at several pressure values and the leaching rate of the radioprotective agents is then measured by spectrophotometry. The relation between the concentration of the active drug and its rate of release, and the effect on the release rate of the pressure applied to the tablet during its formation were also investigated. Results indicating that the release rate was linearly related to the square root of ''t'' seem to be in agreement with what is predictable, according to Higuchi's equation, save for the very initial and terminal phases. A clear correlation was also established between the stearic acid/ethylcellulose ratios and the release of 20% cysteine, namely a marked decrease in the rate of cysteine release was observed with increasing concentrations of stearic acid. Finally, it was observed that a higher formation pressure results in quicker release of the drug

  14. Depressive status explains a significant amount of the variance in COPD assessment test (CAT) scores.

    Science.gov (United States)

    Miravitlles, Marc; Molina, Jesús; Quintano, José Antonio; Campuzano, Anna; Pérez, Joselín; Roncero, Carlos

    2018-01-01

    COPD assessment test (CAT) is a short, easy-to-complete health status tool that has been incorporated into the multidimensional assessment of COPD in order to guide therapy; therefore, it is important to understand the factors determining CAT scores. This is a post hoc analysis of a cross-sectional, observational study conducted in respiratory medicine departments and primary care centers in Spain with the aim of identifying the factors determining CAT scores, focusing particularly on the cognitive status measured by the Mini-Mental State Examination (MMSE) and levels of depression measured by the short Beck Depression Inventory (BDI). A total of 684 COPD patients were analyzed; 84.1% were men, the mean age of patients was 68.7 years, and the mean forced expiratory volume in 1 second (%) was 55.1%. Mean CAT score was 21.8. CAT scores correlated with the MMSE score (Pearson's coefficient r =-0.371) and the BDI ( r =0.620), both p CAT scores and explained 45% of the variability. However, a model including only MMSE and BDI scores explained up to 40% and BDI alone explained 38% of the CAT variance. CAT scores are associated with clinical variables of severity of COPD. However, cognitive status and, in particular, the level of depression explain a larger percentage of the variance in the CAT scores than the usual COPD clinical severity variables.

  15. Comparison of in vitro histamine release by ionic and nonionic radiographyic contrast media

    International Nuclear Information System (INIS)

    Faraj, B.A.; Martin, L.G.

    1989-01-01

    This paper discusses a study whose results showed that in 53 hospitalized patients undergoing cardiovascular catheterization, incubation of their blood samples with varying concentrations of an ionic contrast medium (Angiovist-370, 60--631 mM) induced a significant (P < .005) amount of histamine release from whole blood (3.5%--10%), as compared with the histamine release following incubation with a nonionic contrast medium. Data suggest that the use of nonionic contrast media may induce minimal histamine release and thereby involve less patient risk from the histamine-mediated allergic and hemodynamic side effects associated with radiographic contrast media procedures

  16. Effect of a new drug releasing system on microencapsulated islet transplantation

    Science.gov (United States)

    Lu, Binjie; Gao, Qingkun; Liu, Rui; Ren, Ming; Wu, Yan; Jiang, Zaixing; Zhou, Yi

    2015-01-01

    Objective: This study aimed to develop a novel release system for grafted islets. Materials and methods: A graphene oxide-FTY720 release system was constructed to test the drug loading and releasing capacity. The recipient rats were divided into four groups as following: Experiment group A (EG A) and B (EG B); Control group A (CG A) and B (CG B). In each group, (2000±100) IEQ microencapsulated islets were implanted into the abdominal cavity of the recipients with oral FTY720, local graphene oxide-FTY720 injection, without immunosuppressants, and with graphene oxide-saturated solution respectively. We detected the immunological data, the blood glucose level, and pericapsular overgrowth to show the transplantation effect. Results: 31% of adsorptive FTY720 was released within 6 h, and 82% of FTY720 was released within 48 h. From day 5 to 8, the amount of PBL in EG B was significantly less than those in EG A (PGraphene oxide-FTY720 complex showed a drug releasing effect. Local application of graphene-FTY720 releasing system could decrease the amount of peripheral blood lymphocytes (PBL) and the percentage of CD3 and CD8 T lymphocytes in blood for longer time than oral drug application. This releasing system could achieve a better blood glucose control. PMID:26722425

  17. Determination of accident related release data

    International Nuclear Information System (INIS)

    Koch, W.; Nolte, O.; Lange, F.; Martens, R.

    2004-01-01

    For accident safety analyses, for the assessment of potential radiological consequences, for the review of current requirements of the Transport Regulations and for their possible further development as well as for the demonstration that radioactive materials such as LDM candidate material fulfil the regulatory requirements reliable release data following mechanical impact are required. This is definitely one of the demanding issues in the field of transport safety of radioactive materials. In this context special attention has to be paid to radioactive wastes immobilised in brittle materials, e.g. cement/concrete, glass, ceramics or other brittle materials such as fresh and spent fuel. In this presentation we report on a long-term experimental program aiming at improving the general physical understanding of the release process as well as the quantity and the quality of release data. By combining laboratory experiments using small scale test specimens with a few key scaling experiments with large scale test objects significant progress was achieved to meet this objective. The laboratory equipment enables the in-situ determination of the amount and aerodynamic size distribution of the airborne particles generated upon impact of the test specimen on a hard target. Impact energies cover the range experienced in transport accidents including aircraft accidents. The well defined experimental boundary conditions and the good reproducibility of the experimental procedure allowed for systematic studies to exactly measure the amount and aerodynamic size distribution of the airborne release and to quantify its dependence on relevant parameters such as energy input, material properties, and specimen geometry. The experimental program was performed within the scope of various national and international (e.g. EU-funded) projects. The small scale experiments with brittle materials revealed a pronounced universality of the airborne release in view of the material properties and

  18. 24 CFR 201.10 - Loan amounts.

    Science.gov (United States)

    2010-04-01

    ... 24 Housing and Urban Development 2 2010-04-01 2010-04-01 false Loan amounts. 201.10 Section 201.10... MORTGAGE AND LOAN INSURANCE PROGRAMS UNDER NATIONAL HOUSING ACT AND OTHER AUTHORITIES TITLE I PROPERTY IMPROVEMENT AND MANUFACTURED HOME LOANS Loan and Note Provisions § 201.10 Loan amounts. (a) Property...

  19. Measuring method for amount of fissionable gas in spent fuel pellet

    International Nuclear Information System (INIS)

    Kashibe, Shinji.

    1992-01-01

    The method of the present invention separately measures the amount of both of a fission product (FP) gas accumulated in bubbles at the crystal grain boundary of spent fuel pellets and an FP gas accumulated in the crystal grains. That is, in a radial position of the spent fuel pellet, a microfine region is mechanically destroyed. The amount of the FP gas released by the destruction from the crystal grains is measured by using a mass analyzer. Then, when the destroyed pieces formed by the destruction are recovered and dissolved, FP gas accumulated in the crystal grains of the pellet is released. The amount released is measured by the mass analyzer. With such procedures, the amount of FP gas accumulated in the bubbles at the crystal grain boundary and in the crystal grains at the radial position of the spent fuel pellet can be measured discriminately. Accordingly, the integrity of the fuel pellet can be recognized appropriately. (I.S.)

  20. Sustained release of fungicide metalaxyl by mesoporous silica nanospheres

    Energy Technology Data Exchange (ETDEWEB)

    Wanyika, Harrison, E-mail: hwanyika@gmail.com [Jomo Kenyatta University of Agriculture and Technology, Department of Chemistry (Kenya)

    2013-08-15

    The use of nanomaterials for the controlled delivery of pesticides is nascent technology that has the potential to increase the efficiency of food production and decrease pollution. In this work, the prospect of mesoporous silica nanoparticles (MSN) for storage and controlled release of metalaxyl fungicide has been investigated. Mesoporous silica nanospheres with average particle diameters of 162 nm and average pore sizes of 3.2 nm were prepared by a sol-gel process. Metalaxyl molecules were loaded into MSN pores from an aqueous solution by a rotary evaporation method. The loaded amount of metalaxyl as evaluated by thermogravimetric analysis was about 14 wt%. Release of the fungicide entrapped in the MSN matrix revealed sustained release behavior. About 76 % of the free metalaxyl was released in soil within a period of 30 days while only 11.5 and 47 % of the metalaxyl contained in the MSN carrier was released in soil and water, respectively, within the same period. The study showed that MSN can be used to successfully store metalaxyl molecules in its mesoporous framework and significantly delay their release in soil.

  1. Sustained release of fungicide metalaxyl by mesoporous silica nanospheres

    International Nuclear Information System (INIS)

    Wanyika, Harrison

    2013-01-01

    The use of nanomaterials for the controlled delivery of pesticides is nascent technology that has the potential to increase the efficiency of food production and decrease pollution. In this work, the prospect of mesoporous silica nanoparticles (MSN) for storage and controlled release of metalaxyl fungicide has been investigated. Mesoporous silica nanospheres with average particle diameters of 162 nm and average pore sizes of 3.2 nm were prepared by a sol–gel process. Metalaxyl molecules were loaded into MSN pores from an aqueous solution by a rotary evaporation method. The loaded amount of metalaxyl as evaluated by thermogravimetric analysis was about 14 wt%. Release of the fungicide entrapped in the MSN matrix revealed sustained release behavior. About 76 % of the free metalaxyl was released in soil within a period of 30 days while only 11.5 and 47 % of the metalaxyl contained in the MSN carrier was released in soil and water, respectively, within the same period. The study showed that MSN can be used to successfully store metalaxyl molecules in its mesoporous framework and significantly delay their release in soil

  2. TEGDMA and UDMA monomers released from composite dental material polymerized with diode and halogen lamps.

    Science.gov (United States)

    Wacławczyk, Agnieszka; Postek-Stefańska, Lidia; Pietraszewska, Daria; Birkner, Ewa; Zalejska-Fiolka, Jolanta; Wysoczańska-Jankowicz, Iwona

    2018-03-20

    More than 35 substances released from composite fillings have been identified. Among these, basic monomers and the so-called co-monomers are most often reported. The substances released from polymer-based materials demonstrate allergenic, cytotoxic, genotoxic, mutagenic, embryotoxic, teratogenic, and estrogenic properties. The aim of this study was to measure the amounts of triethylene glycol dimethacrylate (TEGDMA) and urethane dimethacrylate (UDMA) monomers released from composite dental fillings to citrate-phosphate buffer with the pH of 4, 6, 8 after 24 h and 6 months from the polymerization. Ten samples for each polymerization method had been made from the composite material (Filtek Supreme XT, 3M ESPE, St. Paul, USA), which underwent polymerization using the following lamps: halogen lamp (Translux CL, Heraeus Kulzer, Hanau, Germany) (sample H) and diode lamp (Elipar Freelight 2, 3M ESPE), with soft start function (group DS) and without that function (group DWS). It has been demonstrated that the type of light-curing units has a significant impact on the amount of TEGDMA and UDMA released. The amount of UDMA and TEGDMA monomers released from composite fillings differed significantly depending on the source of polymerization applied, as well as the pH of the solution and sample storage time. Elution of the monomers from composite material polymerized using halogen lamp was significantly greater as compared to curing with diode lamps.

  3. 131I release from a HTGR during the LOFC accident

    International Nuclear Information System (INIS)

    Foley, J.E.

    1975-03-01

    The time-dependent release of 131 I from both the core and the containment building of a high temperature gas-cooled (HTGR) reactor during the loss of forced coolant (LOFC) accident is studied. A simplified core release model is combined with a containment building release model so that the total amount of the isotope released to the environment can be calculated. The time-dependent release of 131 I from the core during the LOFC accident is primarily a function of the time-dependent core temperatures and the failed fuel release constants. The most important factor in calculating the amount of the isotope released to the environment is the total amount released into the containment building. (U.S.)

  4. Gas revenue increasingly significant

    International Nuclear Information System (INIS)

    Megill, R.E.

    1991-01-01

    This paper briefly describes the wellhead prices of natural gas compared to crude oil over the past 70 years. Although natural gas prices have never reached price parity with crude oil, the relative value of a gas BTU has been increasing. It is one of the reasons that the total amount of money coming from natural gas wells is becoming more significant. From 1920 to 1955 the revenue at the wellhead for natural gas was only about 10% of the money received by producers. Most of the money needed for exploration, development, and production came from crude oil. At present, however, over 40% of the money from the upstream portion of the petroleum industry is from natural gas. As a result, in a few short years natural gas may become 50% of the money revenues generated from wellhead production facilities

  5. Piezo1 regulates mechanotransductive release of ATP from human RBCs.

    Science.gov (United States)

    Cinar, Eyup; Zhou, Sitong; DeCourcey, James; Wang, Yixuan; Waugh, Richard E; Wan, Jiandi

    2015-09-22

    Piezo proteins (Piezo1 and Piezo2) are recently identified mechanically activated cation channels in eukaryotic cells and associated with physiological responses to touch, pressure, and stretch. In particular, human RBCs express Piezo1 on their membranes, and mutations of Piezo1 have been linked to hereditary xerocytosis. To date, however, physiological functions of Piezo1 on normal RBCs remain poorly understood. Here, we show that Piezo1 regulates mechanotransductive release of ATP from human RBCs by controlling the shear-induced calcium (Ca(2+)) influx. We find that, in human RBCs treated with Piezo1 inhibitors or having mutant Piezo1 channels, the amounts of shear-induced ATP release and Ca(2+) influx decrease significantly. Remarkably, a critical extracellular Ca(2+) concentration is required to trigger significant ATP release, but membrane-associated ATP pools in RBCs also contribute to the release of ATP. Our results show how Piezo1 channels are likely to function in normal RBCs and suggest a previously unidentified mechanotransductive pathway in ATP release. Thus, we anticipate that the study will impact broadly on the research of red cells, cellular mechanosensing, and clinical studies related to red cell disorders and vascular disease.

  6. Disposition of actinides released from high-level waste glass

    International Nuclear Information System (INIS)

    Ebert, W.L.; Bates, J.K.; Buck, E.C.; Gong, M.; Wolf, S.F.

    1994-01-01

    The disposition of actinide elements released from high-level waste glasses into a tuff groundwater in laboratory tests at 90 degrees C at various glass surface area/leachant volume ratios (S/V) between dissolved, suspended, and sorbed fractions has been measured. While the maximum release of actinides is controlled by the corrosion rate of the glass matrix, their solubility and sorption behavior affects the amounts present in potentially mobile phases. Actinide solubilities are affected by the solution pH and the presence of complexants released from the glass, such as sulfate, phosphate, and chloride, radiolytic products, such as nitrate and nitrite, and carbonate. Sorption onto inorganic colloids formed during lass corrosion may increase the amounts of actinides in solution, although subsequent sedimentation of these colloids under static conditions leads to a significant reduction in the amount of actinides in solution. The solution chemistry and observed actinide behavior depend on the S/V of the test. Tests at high S/V lead to higher pH values, greater complexant concentrations, and generate colloids more quickly than tests at low S/V. The S/V also affects the rate of glass corrosion

  7. Trace amount analysis using spark mass spectrometry

    International Nuclear Information System (INIS)

    Stefani, Rene

    1975-01-01

    Characteristics of spark mass spectrometers (ion source, properties of the ion beam, ion optics, and performance) and their use in qualitative and quantitative analysis are described. This technique is very interesting for the semi-quantitative analysis of trace amounts, down to 10 -8 atoms. Examples of applications such as the analysis of high purity materials and non-conducting mineral samples, and determination of carbon and gas trace amounts are presented. (50 references) [fr

  8. Stimuli responsive nanomaterials for controlled release applications

    KAUST Repository

    Li, Song

    2012-01-01

    The controlled release of therapeutics has been one of the major challenges for scientists and engineers during the past three decades. Coupled with excellent biocompatibility profiles, various nanomaterials have showed great promise for biomedical applications. Stimuli-responsive nanomaterials guarantee the controlled release of cargo to a given location, at a specific time, and with an accurate amount. In this review, we have combined the major stimuli that are currently used to achieve the ultimate goal of controlled and targeted release by "smart" nanomaterials. The most heavily explored strategies include (1) pH, (2) enzymes, (3) redox, (4) magnetic, and (5) light-triggered release.

  9. Determination of metal ions released by stainless steel arch bar into bio-fluids

    Directory of Open Access Journals (Sweden)

    Lori A. Joseph

    2009-04-01

    Full Text Available The amounts of cobalt, iron, manganese, nickel and chromium ions released from new and reused stainless steel arch bar used for maxillomandibular fixation was determined in Hank’s solutions of different hydrogen and chloride ions concentrations, whole blood serum and phosphate buffered saline (PBS in vitro, over a six-week immersion time at 37 oC, by atomic absorption spectrophotometry. The corrosion levels of the wires due to effects of media and incubation times in the bio-fluids were compared by Duncan’s two-way ANOVA (P less than 0.05. Pearson’s correlation was used in establishing relationship in the amounts of metal ions released by new and reused arch bars. The study indicated that the reused wires released more ions than new ones at all time points. The variation of pH and chloride ions of the bio-fluids had a significant effect on the amount of Ni, Mn and Cr ions released. Ageing prior use of arch bars significantly increased Ni ions released into the bio-fluids.

  10. Formulation And Evaluation Of Bilayer Tablet for Bimodal Release of Venlafaxine Hydrochloride

    Directory of Open Access Journals (Sweden)

    Munira eMomin

    2015-07-01

    Full Text Available The aim of the present research was to develop a bilayer tablet of venlafexine hydrochloride for bimodal drug release. In the present investigation authors have tried to explore Fenugreek Mucilage (FNM for bioadhesive sustained release layer. The attempt has been made to combine FNM with well studied bioahesive polymers like Hydroxy Propyl Methyl Cellulose, Carbopol and Xanthan Gum. The formulations were evaluated for swelling Index, ex-vivo bioadhesion, water uptake studies, in-vitro drug release and dissolution kinetics was studied. Substantial bioadhesion force (2.4±0.023 gms and tablet adhesion retention time (24±2 hrs was observed with FNM and HPMC combination at 80:20 ratio. The dissolution kinetics followed the Higuchi model (R2 =0.9913 via a non-Fickian diffusion controlled release mechanism after the initial burst. The 32 full factorial design was employed in the present study. The type of polymers used in combination with FNM (X1 and percent polymer replaced with FNM (X2 were taken as independent formulations variables. The selected responses, bioadhesion force (0.11-0.25±0.023gm, amount of drug released in 10 h, Y10 (78.20–95.78±1.24 % and bioadhesive strength, (19-24±2hrs presented good correlation with the selected independent variables. Statistical analysis (ANOVA of the optimized bilayer formulations showed no significant difference in the cumulative amount of drug release after 15 min, but significant difference (p < 0.05 in the amount of drug released after 1 hr till 12 h from optimized formulations was observed. The natural mucilage like FNM could be successfully incorporated into tablet with only 20% replacement with HPMC and it showed good bioadhesiveness and sustained drug release.

  11. Commercial SNF Accident Release Fractions

    Energy Technology Data Exchange (ETDEWEB)

    J. Schulz

    2004-11-05

    The purpose of this analysis is to specify and document the total and respirable fractions for radioactive materials that could be potentially released from an accident at the repository involving commercial spent nuclear fuel (SNF) in a dry environment. The total and respirable release fractions are used to support the preclosure licensing basis for the repository. The total release fraction is defined as the fraction of total commercial SNF assembly inventory, typically expressed as an activity inventory (e.g., curies), of a given radionuclide that is released to the environment from a waste form. Radionuclides are released from the inside of breached fuel rods (or pins) and from the detachment of radioactive material (crud) from the outside surfaces of fuel rods and other components of fuel assemblies. The total release fraction accounts for several mechanisms that tend to retain, retard, or diminish the amount of radionuclides that are available for transport to dose receptors or otherwise can be shown to reduce exposure of receptors to radiological releases. The total release fraction includes a fraction of airborne material that is respirable and could result in inhalation doses; this subset of the total release fraction is referred to as the respirable release fraction. Accidents may involve waste forms characterized as: (1) bare unconfined intact fuel assemblies, (2) confined intact fuel assemblies, or (3) canistered failed commercial SNF. Confined intact commercial SNF assemblies at the repository are contained in shipping casks, canisters, or waste packages. Four categories of failed commercial SNF are identified: (1) mechanically and cladding-penetration damaged commercial SNF, (2) consolidated/reconstituted assemblies, (3) fuel rods, pieces, and debris, and (4) nonfuel components. It is assumed that failed commercial SNF is placed into waste packages with a mesh screen at each end (CRWMS M&O 1999). In contrast to bare unconfined fuel assemblies, the

  12. Commercial SNF Accident Release Fractions

    International Nuclear Information System (INIS)

    Schulz, J.

    2004-01-01

    The purpose of this analysis is to specify and document the total and respirable fractions for radioactive materials that could be potentially released from an accident at the repository involving commercial spent nuclear fuel (SNF) in a dry environment. The total and respirable release fractions are used to support the preclosure licensing basis for the repository. The total release fraction is defined as the fraction of total commercial SNF assembly inventory, typically expressed as an activity inventory (e.g., curies), of a given radionuclide that is released to the environment from a waste form. Radionuclides are released from the inside of breached fuel rods (or pins) and from the detachment of radioactive material (crud) from the outside surfaces of fuel rods and other components of fuel assemblies. The total release fraction accounts for several mechanisms that tend to retain, retard, or diminish the amount of radionuclides that are available for transport to dose receptors or otherwise can be shown to reduce exposure of receptors to radiological releases. The total release fraction includes a fraction of airborne material that is respirable and could result in inhalation doses; this subset of the total release fraction is referred to as the respirable release fraction. Accidents may involve waste forms characterized as: (1) bare unconfined intact fuel assemblies, (2) confined intact fuel assemblies, or (3) canistered failed commercial SNF. Confined intact commercial SNF assemblies at the repository are contained in shipping casks, canisters, or waste packages. Four categories of failed commercial SNF are identified: (1) mechanically and cladding-penetration damaged commercial SNF, (2) consolidated/reconstituted assemblies, (3) fuel rods, pieces, and debris, and (4) nonfuel components. It is assumed that failed commercial SNF is placed into waste packages with a mesh screen at each end (CRWMS M andO 1999). In contrast to bare unconfined fuel assemblies, the

  13. Endurance exercise modulates levodopa induced growth hormone release in patients with Parkinson's disease.

    Science.gov (United States)

    Müller, Thomas; Welnic, Jacub; Woitalla, Dirk; Muhlack, Siegfried

    2007-07-11

    Acute levodopa (LD) application and exercise release human growth hormone (GH). An earlier trial showed, that combined stimulus of exercise and LD administration is the best provocative test for GH response in healthy participants. Objective was to show this combined effect of LD application and exercise on GH response and to investigate the impact on LD metabolism in 20 previously treated patients with Parkinson's disease (PD). We measured GH- and LD plasma concentrations following soluble 200 mg LD/50 mg benserazide administration during endurance exercise and rest on two separate consecutive days. GH concentrations significantly increased on both days, but GH release was significantly delayed during rest. LD metabolism was not altered due to exercise in a clinical relevant manner. Exercise induced a significant faster LD stimulated GH release in comparison with the rest condition. We did not find the supposed increase of LD induced GH release by endurance exercise. We assume, that only a limited amount of GH is available for GH release in the anterior pituitary following an acute 200 mg LD administration. GH disposal also depends on growth hormone releasing hormone (GHRH), which is secreted into hypothalamic portal capillaries. During the exercise condition, the resulting higher blood pressure supports blood flow and thus GHRH transport towards the GH producing cells in the pituitary. This might additionally have caused the significant faster GH release during exercise.

  14. Comparative evaluation of fluoride release from PRG-composites and compomer on application of topical fluoride: An in-vitro study

    Directory of Open Access Journals (Sweden)

    Dhull K

    2009-03-01

    Full Text Available Aims and Objective: To determine the fluoride release from Giomer and Compomer, using different topical fluoride regimes, and to compare the amount of fluoride release from giomer with that of compomer. Materials and Method: Forty-eight specimens of each giomer and compomer were divided into four treatment groups, namely, control group, fluoridated dentifrice (500 ppm once daily group, fluoridated dentifrice (500 ppm twice daily group, fluoridated dentifrice (500 ppm once daily + fluoridated mouthwash (225 ppm group. Each specimen was suspended in demineralizing solution for six hours and remineralizing solution for 18 hours. Fluoride release was measured in both the demineralizing solution and remineralizing solution daily for seven days. Total daily fluoride release for each specimen was calculated by adding the amount released in the demineralizing solution to that released in remineralizing solution. Results and Conclusion: The fluoride release (ppm was found to be more in Giomer when compared to Compomer. The fluoride released from Giomer and Compomer was significantly greater in the acidic demineralizing solution than in the neutral remineralizing solution. It was found that increasing fluoride exposure significantly increased fluoride release from the giomer and compomer. It was found that the fluoride release from the subgroups of giomer and compomer was in the following order: fluoridated dentifrice twice daily > fluoridated dentifrice once daily + fluoridated mouthwash > fluoridated dentifrice once daily > control group. It was found that the giomer showed a greater fluoride uptake than the compomer.

  15. Toxic releases from power plants

    International Nuclear Information System (INIS)

    Rubin, E.S.

    1999-01-01

    Beginning in 1998, electric power plants burning coal or oil must estimate and report their annual releases of toxic chemicals listed in the Toxics Release Inventory (TRI) published by the US Environmental Protection Agency (EPA). This paper identifies the toxic chemicals of greatest significance for the electric utility sector and develops quantitative estimates of the toxic releases reportable to the TRI for a representative coal-fired power plant. Key factors affecting the magnitude and types of toxic releases for individual power plants also are discussed. A national projection suggests that the magnitude of electric utility industry releases will surpass those of the manufacturing industries which current report to the TRI. Risk communication activities at the community level will be essential to interpret and provide context for the new TRI results

  16. Effect of non-cross-linked calcium on characteristics, swelling behaviour, drug release and mucoadhesiveness of calcium alginate beads.

    Science.gov (United States)

    Dalaty, Adnan Al; Karam, Ayman; Najlah, Mohammad; Alany, Raid G; Khoder, Mouhamad

    2016-04-20

    In this study, ibuprofen-loaded calcium alginate beads (CABs) with varying amounts of non-cross-linked calcium (NCL-Ca) were prepared using different washing methods. The influence of NCL-Ca on beads properties was investigated. Increasing the number or duration of washes led to significant decreases in the amount of NCL-Ca whereas the impact of the volume of washes was not significant. Approximately 70% of the initial amount of Ca(2+) was NCL-Ca which was removable by washing while only 30% was cross-linked (CL-Ca). Ca(2+) release from the CABs was bimodal; NCL-Ca was burst-released followed by a slower release of CL-Ca. Washing methods and the amount of NCL-Ca had significant influences on the encapsulation efficiency, beads weight, beads swelling, drug release profile and the mucoadhesiveness of CABs. This study highlighted the importance of washing methods and the amount of NCL-Ca to establish CABs properties and understand their behaviour in the simulated intestinal fluids (SIFs). Copyright © 2015 Elsevier Ltd. All rights reserved.

  17. Nanosized sustained-release pyridostigmine bromide microcapsules: process optimization and evaluation of characteristics

    Science.gov (United States)

    Tan, Qunyou; Jiang, Rong; Xu, Meiling; Liu, Guodong; Li, Songlin; Zhang, Jingqing

    2013-01-01

    Background Pyridostigmine bromide (3-[[(dimethylamino)-carbonyl]oxy]-1-methylpyridinium bromide), a reversible inhibitor of cholinesterase, is given orally in tablet form, and a treatment schedule of multiple daily doses is recommended for adult patients. Nanotechnology was used in this study to develop an alternative sustained-release delivery system for pyridostigmine, a synthetic drug with high solubility and poor oral bioavailability, hence a Class III drug according to the Biopharmaceutics Classification System. Novel nanosized pyridostigmine-poly(lactic acid) microcapsules (PPNMCs) were expected to have a longer duration of action than free pyridostigmine and previously reported sustained-release formulations of pyridostigmine. Methods The PPNMCs were prepared using a double emulsion-solvent evaporation method to achieve sustained-release characteristics for pyridostigmine. The preparation process for the PPNMCs was optimized by single-factor experiments. The size distribution, zeta potential, and sustained-release behavior were evaluated in different types of release medium. Results The optimal volume ratio of inner phase to external phase, poly(lactic acid) concentration, polyvinyl alcohol concentration, and amount of pyridostigmine were 1:10, 6%, 3% and 40 mg, respectively. The negatively charged PPNMCs had an average particle size of 937.9 nm. Compared with free pyridostigmine, PPNMCs showed an initial burst release and a subsequent very slow release in vitro. The release profiles for the PPNMCs in four different types of dissolution medium were fitted to the Ritger-Peppas and Weibull models. The similarity between pairs of dissolution profiles for the PPNMCs in different types of medium was statistically significant, and the difference between the release curves for PPNMCs and free pyridostigmine was also statistically significant. Conclusion PPNMCs prepared by the optimized protocol described here were in the nanometer range and had good uniformity

  18. Ion release from orthodontic brackets in 3 mouthwashes: an in-vitro study.

    Science.gov (United States)

    Danaei, Shahla Momeni; Safavi, Afsaneh; Roeinpeikar, S M Mehdi; Oshagh, Morteza; Iranpour, Shiva; Omidkhoda, Maryam; Omidekhoda, Maryam

    2011-06-01

    Stainless steel orthodontic brackets can release metal ions into the saliva. Fluoridated mouthwashes are often recommended to orthodontic patients to reduce the risk of white-spot lesions around their brackets. However, little information is available regarding the effect of different mouthwashes in ion release of orthodontic brackets. The purpose of this study was to measure the amount of metal ion release from orthodontic brackets when kept in different mouthwashes. One hundred sixty stainless steel brackets (0.022-in, 3M Unitek, Monrovia, Calif) were divided randomly into 4 equal groups and immersed in Oral B (Procter & Gamble, Weybridge, United Kingdom), chlorhexidine (Shahdaru Labratories, Tehran, Iran), and Persica (Poursina Pharmaceutical Laboratories, Tehran, Iran) mouthwashes and distilled deionized water and incubated at 37°C for 45 days. Nickel, chromium, iron, copper, and manganese released from the orthodontic brackets were measured with an inductively coupled plasma spectrometer. For statistical analysis, 1-way analysis of variance (ANOVA) and the Duncan multiple-range tests were used. The results showed that ion release in deionized water was significantly (P 0.05) in nickel, chromium, iron, and copper ion release in the Oral B and Persica mouthwashes. The level of manganese release was significantly different in all 4 groups. If ion release is a concern, Oral B and Persica mouthwashes might be better options than chlorhexidine for orthodontic patients with stainless steel brackets. Copyright © 2011 American Association of Orthodontists. Published by Mosby, Inc. All rights reserved.

  19. 29 CFR 4219.14 - Amount of liability for 20-year-limitation amounts.

    Science.gov (United States)

    2010-07-01

    ... amount equal to the present value of all initial withdrawal liability payments for which the employer was not liable pursuant to section 4219(c)(1)(B) of ERISA. The present value of such payments shall be... 29 Labor 9 2010-07-01 2010-07-01 false Amount of liability for 20-year-limitation amounts. 4219.14...

  20. News/Press Releases

    Data.gov (United States)

    Office of Personnel Management — A press release, news release, media release, press statement is written communication directed at members of the news media for the purpose of announcing programs...

  1. Significant Tsunami Events

    Science.gov (United States)

    Dunbar, P. K.; Furtney, M.; McLean, S. J.; Sweeney, A. D.

    2014-12-01

    Tsunamis have inflicted death and destruction on the coastlines of the world throughout history. The occurrence of tsunamis and the resulting effects have been collected and studied as far back as the second millennium B.C. The knowledge gained from cataloging and examining these events has led to significant changes in our understanding of tsunamis, tsunami sources, and methods to mitigate the effects of tsunamis. The most significant, not surprisingly, are often the most devastating, such as the 2011 Tohoku, Japan earthquake and tsunami. The goal of this poster is to give a brief overview of the occurrence of tsunamis and then focus specifically on several significant tsunamis. There are various criteria to determine the most significant tsunamis: the number of deaths, amount of damage, maximum runup height, had a major impact on tsunami science or policy, etc. As a result, descriptions will include some of the most costly (2011 Tohoku, Japan), the most deadly (2004 Sumatra, 1883 Krakatau), and the highest runup ever observed (1958 Lituya Bay, Alaska). The discovery of the Cascadia subduction zone as the source of the 1700 Japanese "Orphan" tsunami and a future tsunami threat to the U.S. northwest coast, contributed to the decision to form the U.S. National Tsunami Hazard Mitigation Program. The great Lisbon earthquake of 1755 marked the beginning of the modern era of seismology. Knowledge gained from the 1964 Alaska earthquake and tsunami helped confirm the theory of plate tectonics. The 1946 Alaska, 1952 Kuril Islands, 1960 Chile, 1964 Alaska, and the 2004 Banda Aceh, tsunamis all resulted in warning centers or systems being established.The data descriptions on this poster were extracted from NOAA's National Geophysical Data Center (NGDC) global historical tsunami database. Additional information about these tsunamis, as well as water level data can be found by accessing the NGDC website www.ngdc.noaa.gov/hazard/

  2. Observations of the release of non-methane hydrocarbons from fractured shale.

    Science.gov (United States)

    Sommariva, Roberto; Blake, Robert S; Cuss, Robert J; Cordell, Rebecca L; Harrington, Jon F; White, Iain R; Monks, Paul S

    2014-01-01

    The organic content of shale has become of commercial interest as a source of hydrocarbons, owing to the development of hydraulic fracturing ("fracking"). While the main focus is on the extraction of methane, shale also contains significant amounts of non-methane hydrocarbons (NMHCs). We describe the first real-time observations of the release of NMHCs from a fractured shale. Samples from the Bowland-Hodder formation (England) were analyzed under different conditions using mass spectrometry, with the objective of understanding the dynamic process of gas release upon fracturing of the shale. A wide range of NMHCs (alkanes, cycloalkanes, aromatics, and bicyclic hydrocarbons) are released at parts per million or parts per billion level with temperature- and humidity-dependent release rates, which can be rationalized in terms of the physicochemical characteristics of different hydrocarbon classes. Our results indicate that higher energy inputs (i.e., temperatures) significantly increase the amount of NMHCs released from shale, while humidity tends to suppress it; additionally, a large fraction of the gas is released within the first hour after the shale has been fractured. These findings suggest that other hydrocarbons of commercial interest may be extracted from shale and open the possibility to optimize the "fracking" process, improving gas yields and reducing environmental impacts.

  3. Consequences of severe radioactive releases to Nordic Marine environment

    DEFF Research Database (Denmark)

    Iosjpe, M.; Isaksson, M.; Joensen, H.P.

    - or minor – radioactive releases to Nordic marine environment. As a reference, the release amounts from a 3000 MWth reactor size were used. Based on source term analyses, the chosen release fractions in the study were: iodine 20% (of the total core inventory), caesium 10%, tellurium 10%, strontium 0...

  4. Prolactin, thyrotropin, and growth hormone release during stress associated with parachute jumping.

    Science.gov (United States)

    Noel, G L; Dimond, R C; Earll, J M; Frantz, A G

    1976-05-01

    Prolactin, growth hormone, and thyrotropin (TSH) release during the stress of parachute jumping has been evaluated in 14 male subjects. Subjects were studied at several times before and immediately after their first military parachute jump. All three hormones had risen significantly 1 to 14 min after the jump, compared to mean levels measured immediately beforehand. Earlier studies of physical exercise by ourselves and others would suggest that emotional stress played a role in producing changes of this magnitude. We conclude that prolactin, TSH, and growth hormone are released in physiologically significant amounts in association with the stress of parachute jumping.

  5. Effect of food simulating liquids on release of monomers from two dental resin composites

    Directory of Open Access Journals (Sweden)

    Ghavam M

    2010-06-01

    Full Text Available "nBackground and Aims: The elution of residual monomers from cured dental composites to oral cavity has a harmful effect on human health and can affect their clinical durability. The purpose of this study was to evaluate the amount of eluted monomers (Bis-GMA, TEGDMA, UDMA from two types of composites (Gradia and P60 after exposure to food simulating liquids such as ethanol (25, 50, 75 % and heptane 50 % for 24 hours and 7 days. "nMaterials and Methods: Forty specimens of each composite were prepared. Equal numbers of each composite were immersed in tubes containing 2cc volumes of 25, 50, 75 % ethanole and 50 % heptane. The amount of eluted monomers in standard condition such as Bis-GMA, TEGDMA and UDMA was measured by GC/MS (Gas Chromatography/Mass Spectroscopy and results were statistically analysed by three way and one way ANOVA. P<0.05 was considered as the level of significancy. "nResults: The results showed that Gradia released more TEGDMA than P60. In assessing the effect of environment, the result showed that ethanol caused releasing monomers more than heptane and the concentration rate of 75 % ethanole resulted in most releasing of monomers. In assessing the effect of time, the observation showed that more monomers were released 7 days compared to 24 hours. Bis-GMA and UDMA were not detected in any solutions in these conditions. "nConclusion: Ethanole caused more release of monomers than heptane and 75 % ethanole released the most amount of monomers. Gradia released more amount of TEGDMA than P60.

  6. 13 CFR 120.930 - Amount.

    Science.gov (United States)

    2010-01-01

    ... percent of total Project cost plus 100 percent of eligible administrative costs. For good cause shown, SBA... 13 Business Credit and Assistance 1 2010-01-01 2010-01-01 false Amount. 120.930 Section 120.930 Business Credit and Assistance SMALL BUSINESS ADMINISTRATION BUSINESS LOANS Development Company Loan...

  7. 33 CFR 135.203 - Amount required.

    Science.gov (United States)

    2010-07-01

    ... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Amount required. 135.203 Section 135.203 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE POLLUTION FINANCIAL RESPONSIBILITY AND COMPENSATION OFFSHORE OIL POLLUTION COMPENSATION FUND...

  8. Controlled Release Formulations of Auxinic Herbicides

    Science.gov (United States)

    Kowalski, Witold J.; Siłowiecki, Andrzej.; Romanowska, Iwona; Glazek, Mariola; Bajor, Justyna; Cieciwa, Katarzyna; Rychter, Piotr

    2013-04-01

    Controlled release formulations are applied extensively for the release of active ingredients such as plant protection agents and fertilizers in response to growing concern for ecological problems associated with increased use of plant protection chemicals required for intensive agricultural practices [1]. We synthesized oligomeric mixtures of (R,S)-3-hydroxy butyric acid chemically bonded with 2,4-D, Dicamba and MCPA herbicides (HBA) respectively, and determined their molecular structure and molecular weight dispersion by the size exclusion chromatography, proton magnetic resonance spectrometry and electro-spray ionization mass spectrometry. Further we carried out bioassays of herbicidal effectiveness of the HBA herbicides vs. series of dicotyledonous weeds and crop injury tests [2, 3, 4]. Field bioassays were accomplished according to the EPPO standards [5]. Groups of representative weeds (the development stages in the BCCH scale: 10 - 30) were selected as targets. Statistical variabilities were assessed by the Fisher LSD test for plants treated with the studied herbicides in form of HBA oligomers, the reference herbicides in form of dimethyl ammonium salts (DMA), and untreated plants. No statistically significant differences in the crop injuries caused by the HBA vs. the DMA reference formulation were observed. The effectiveness of the HBA herbicides was lower through the initial period (ca. 2 weeks) relative to the DMA salts, but a significant increase in the effectiveness of the HBA systems followed during the remaining fraction of each assay. After 6 weeks all observed efficiencies approached 100%. The death of weeds treated with the HBA herbicides was delayed when compared with the DMA reference herbicides. The delayed uptake observed for the HBA oligomers relative to the DMA salts was due to controlled release phenomena. In case of the DMA salts the total amount of active ingredients was available at the target site. By contrast, the amount of an active

  9. Tailored sequential drug release from bilayered calcium sulfate composites

    International Nuclear Information System (INIS)

    Orellana, Bryan R.; Puleo, David A.

    2014-01-01

    The current standard for treating infected bony defects, such as those caused by periodontal disease, requires multiple time-consuming steps and often multiple procedures to fight the infection and recover lost tissue. Releasing an antibiotic followed by an osteogenic agent from a synthetic bone graft substitute could allow for a streamlined treatment, reducing the need for multiple surgeries and thereby shortening recovery time. Tailorable bilayered calcium sulfate (CS) bone graft substitutes were developed with the ability to sequentially release multiple therapeutic agents. Bilayered composite samples having a shell and core geometry were fabricated with varying amounts (1 or 10 wt.%) of metronidazole-loaded poly(lactic-co-glycolic acid) (PLGA) particles embedded in the shell and simvastatin directly loaded into either the shell, core, or both. Microcomputed tomography showed the overall layered geometry as well as the uniform distribution of PLGA within the shells. Dissolution studies demonstrated that the amount of PLGA particles (i.e., 1 vs. 10 wt.%) had a small but significant effect on the erosion rate (3% vs. 3.4%/d). Mechanical testing determined that introducing a layered geometry had a significant effect on the compressive strength, with an average reduction of 35%, but properties were comparable to those of mandibular trabecular bone. Sustained release of simvastatin directly loaded into CS demonstrated that changing the shell to core volume ratio dictates the duration of drug release from each layer. When loaded together in the shell or in separate layers, sequential release of metronidazole and simvastatin was achieved. By introducing a tunable, layered geometry capable of releasing multiple drugs, CS-based bone graft substitutes could be tailored in order to help streamline the multiple steps needed to regenerate tissue in infected defects. - Highlights: • Bilayered CS composites were fabricated as potential bone graft substitutes. • The shell

  10. Tailored sequential drug release from bilayered calcium sulfate composites

    Energy Technology Data Exchange (ETDEWEB)

    Orellana, Bryan R.; Puleo, David A., E-mail: puleo@uky.edu

    2014-10-01

    The current standard for treating infected bony defects, such as those caused by periodontal disease, requires multiple time-consuming steps and often multiple procedures to fight the infection and recover lost tissue. Releasing an antibiotic followed by an osteogenic agent from a synthetic bone graft substitute could allow for a streamlined treatment, reducing the need for multiple surgeries and thereby shortening recovery time. Tailorable bilayered calcium sulfate (CS) bone graft substitutes were developed with the ability to sequentially release multiple therapeutic agents. Bilayered composite samples having a shell and core geometry were fabricated with varying amounts (1 or 10 wt.%) of metronidazole-loaded poly(lactic-co-glycolic acid) (PLGA) particles embedded in the shell and simvastatin directly loaded into either the shell, core, or both. Microcomputed tomography showed the overall layered geometry as well as the uniform distribution of PLGA within the shells. Dissolution studies demonstrated that the amount of PLGA particles (i.e., 1 vs. 10 wt.%) had a small but significant effect on the erosion rate (3% vs. 3.4%/d). Mechanical testing determined that introducing a layered geometry had a significant effect on the compressive strength, with an average reduction of 35%, but properties were comparable to those of mandibular trabecular bone. Sustained release of simvastatin directly loaded into CS demonstrated that changing the shell to core volume ratio dictates the duration of drug release from each layer. When loaded together in the shell or in separate layers, sequential release of metronidazole and simvastatin was achieved. By introducing a tunable, layered geometry capable of releasing multiple drugs, CS-based bone graft substitutes could be tailored in order to help streamline the multiple steps needed to regenerate tissue in infected defects. - Highlights: • Bilayered CS composites were fabricated as potential bone graft substitutes. • The shell

  11. Orthodontic forces released by low-friction versus conventional systems during alignment of apically or buccally malposed teeth.

    Science.gov (United States)

    Baccetti, Tiziano; Franchi, Lorenzo; Camporesi, Matteo; Defraia, Efisio

    2011-02-01

    The aim of the present study was to analyse the forces released by passive stainless steel self-ligating brackets (SLBs) and by a non-conventional elastomeric ligature-bracket system on conventional brackets ([slide ligatures on conventional brackets (SLCB)]) when compared with conventional elastomeric ligatures on conventional brackets (CLCB) during the alignment of apically or buccally malposed teeth in the maxillary arch. An experimental model consisting of five brackets was used to assess the forces released by the three different bracket-ligature systems with 0.012-inch super-elastic (SE) nickel-titanium (NiTi) wires in the presence of different amounts of apical or buccal canine misalignment of the canine (ranging from 1.5 to 6 mm). The forces released by each wire/bracket/ligature combination with the three different amounts of apical or buccal canine misalignment were tested 20 times. Comparisons between the different types of wire/bracket/ligature systems were carried out by means of analysis of variance on ranks with Dunnett's post hoc test (P < 0.05). No difference in the amount of force released in presence of a misalignment of 1.5 mm was recorded among the three systems. At 3 mm of apical misalignment a significantly greater amount of orthodontic force was released by SLB or SLCB when compared with CLCB, while no significant differences were found among the three systems at 3 mm of buccal canine displacement. When correction of a large amount of misalignment (6 mm) was attempted, a noticeable amount of force for alignment was still generated by the passive SLB and SLCB systems while no force was released in presence of CLCB.

  12. Assessment of the Potential Release of Radioactivity from Installations at AERE, Harwell. Implications for Emergency Planning

    Energy Technology Data Exchange (ETDEWEB)

    Flew, Elizabeth M.; Lister, B. A.J. [Atomic Energy Research Establishment, Harwell, Didcot, Berks. (United Kingdom)

    1969-10-15

    As part of a review of the site emergency organization at AERE, a realistic reappraisal has been made of the potential hazard to the establishment and district of all the buildings containing significant amounts of radioactive materials. To assess the amount of radioactive material which might be released under specified accident conditions, four factors have been applied to the total building stock: (a) the fraction of the stock involved, (b) the percentage conversion to an aerosol form, (c) release from primary containment and (d) release from the building. These potential release figures have been compared with ''site hazardous release'' figures for relevant radionuclides i.e., amounts which could give rise to exposure above defined reference levels. Those buildings with more than one tenth of the potential for causing; a site or district hazard have been designated ''risk buildings''. Such a quantitative assessment, although necessarily very approximate, has been of considerable value in determining the type and complexity of the central emergency organization required and in producing the right emphasis on exercises, training, liaison with outside bodies, etc. (author)

  13. Analysis of drug effects on neurotransmitter release

    International Nuclear Information System (INIS)

    Rowell, P.; Garner, A.

    1986-01-01

    The release of neurotransmitter is routinely studied in a superfusion system in which serial samples are collected and the effects of drugs or other treatments on the amount of material in the superfusate is determined. With frequent sampling interval, this procedure provides a mechanism for dynamically characterizing the release process itself. Using automated data collection in conjunction with polyexponential computer analysis, the equation which describes the release process in each experiment is determined. Analysis of the data during the nontreated phase of the experiment allows an internal control to be used for accurately assessing any changes in neurotransmitter release which may occur during a subsequent treatment phase. The use of internal controls greatly improves the signal to noise ratio and allows determinations of very low concentrations of drugs on small amounts of tissue to be made. In this presentation, the effects of 10 μM nicotine on 3 H-dopamine release in rat nucleus accumbens is described. The time course, potency and efficacy of the drug treatment is characterized using this system. Determinations of the exponential order of the release as well as the rate constants allow one to study the mechanism of the release process. A description of 3 H-dopamine release in normal as well as Ca ++ -free medium is presented

  14. Increasing potassium (K release from K-containing minerals in the presence of insoluble phosphate by bacteria

    Directory of Open Access Journals (Sweden)

    Mohammad Reza Sarikhani

    2016-03-01

    Full Text Available Introduction: Phosphorus and potassium are major essential macronutrients for biological growth and development. Application of soil microorganisms is one approach to enhance crop growth. Some bacteria are efficient in releasing K and solubilizing P from mineral sources but their behavior was not studied more in presence together. Materials and methods: In this study the ability of seven bacterial strains, including Pseudomonas putida P13, P. putida Tabriz, P. fluorescens Tabriz, P. fluorescens Chao, Pantoea agglomerans P5, Azotobacter sp. and Bacillus megaterium JK3 to release mineral K from muscovite and biotite with application of insoluble (Ca3(PO42 or soluble (Na2HPO4 P-sources was investigated. Nutrient Broth was used to prepare an overnight culture of bacteria to inoculate in Aleksandrov medium, which was used to study the dissolution of silicate minerals. It should be mentioned that Aleksandrov medium was used to determine the amount of released P from tricalcium phosphate (TCP while muscovite was added to the medium as a sole source of potassium. Concentration of P was determined spectrophotometrically by ammonium-vanadate-molybdate method and K was determined by flame photometry. Results: The insoluble P-source led to a significantly increased released K into assay medium (66%, and the net release of K from the biotite was significantly enhanced. Among bacterial strains, the highest mean of released K was observed with P. putida P13 which released more K (27% than the control. The amounts of released K from micas in the presence of insoluble and soluble phosphate by P. putida P13 were 8.25 and 4.87 mg/g, respectively. Discussion and conclusion: Application of insoluble phosphate could increase K release from mica minerals. The enhanced releasing of mineral K might be attributed to the release of organic acids from the bacteria, a mechanism which plays a pivotal role in solubilizing phosphate from inorganic source of phosphate.

  15. Radiculography with reduced amounts of contrast medium

    International Nuclear Information System (INIS)

    Signorini, E.; Caputo, N.; Chiurulla, C.; Ciorba, E.; Pelliccioli, G.P.; Cianciulli, E.

    1984-01-01

    Because of the frequency and seriousness of side effects observed after radiculography, due to, among the other things, the amount of contrast medium, the authors describe a method that gives diagnostically satisfactory results using a low dose of contrast and a tangent-beam technique. Among 106 patients undergoing radiculography with a tangent-beam technique and Iopamidol, only 4 developed mild side effects, namely headache in three cases and headache with nausea in one. (Author)

  16. In situ release rates of Cu and Zn from commercial antifouling paints at different salinities.

    Science.gov (United States)

    Lagerström, Maria; Lindgren, J Fredrik; Holmqvist, Albin; Dahlström, Mia; Ytreberg, Erik

    2018-02-01

    Antifouling paints are environmentally risk assessed based on their biocidal release rates to the water phase. In situ release rates of copper (Cu) and zinc (Zn) were derived for five commercial paints in two recreational marinas with different salinities (5 and 14 PSU) using an X-Ray Fluorescence spectrometer (XRF). Salinity was found to significantly affect the Cu release, with twice the amount of Cu released at the higher salinity, while its influence on the Zn release was paint-specific. Site-specific release rates for water bodies with salinity gradients, e.g. the Baltic Sea, are therefore necessary for more realistic risk assessments of antifouling paints. Furthermore, the in situ release rates were up to 8 times higher than those generated using standardized laboratory or calculation methods. The environmental risk assessment repeated with the field release rates concludes that it is questionable whether the studied products should be allowed on the Swedish market. Copyright © 2017 The Authors. Published by Elsevier Ltd.. All rights reserved.

  17. Spray drying of silica microparticles for sustained release application with a new sol-gel precursor.

    Science.gov (United States)

    Wang, Bifeng; Friess, Wolfgang

    2017-10-30

    A new precursor, tetrakis(2-methoxyethyl) orthosilicate (TMEOS) was used to fabricate microparticles for sustained release application, specifically for biopharmaceuticals, by spray drying. The advantages of TMEOS over the currently applied precursors are its water solubility and hydrolysis at moderate pH without the need of organic solvents or catalyzers. Thus a detrimental effect on biomolecular drug is avoided. By generating spray-dried silica particles encapsulating the high molecular weight model compound FITC-dextran 150 via the nano spray dryer Büchi-90, we demonstrated how formulation parameters affect and enable control of drug release properties. The implemented strategies to regulate release included incorporating different quantities of dextrans with varying molecular weight as well as adjusting the pH of the precursor solution to modify the internal microstructures. The addition of dextran significantly altered the released amount, while the release became faster with increasing dextran molecular weight. A sustained release over 35days could be achieved with addition of 60 kD dextran. The rate of FITC-Dextran 150 release from the dextran 60 containing particles decreased with higher precursor solution pH. In conclusion, the new precursor TMEOS presents a promising alternative sol-gel technology based carrier material for sustained release application of high molecular weight biopharmaceutical drugs. Copyright © 2017 Elsevier B.V. All rights reserved.

  18. Environmental transport and long-term exposure for tritium released in the biosphere

    International Nuclear Information System (INIS)

    Bergman, R.; Bergstroem, U.; Evans, S.

    1979-01-01

    Global cycling of tritium is studied with regard to long-term exposure and dose. Dose and dose commitment are calculated for releases at different latitudes to the troposphere, land and upper ocean layer, with particular regard to effects from release into recipients of intermediate size as, for example, the Baltic Sea. The global transport of tritium appears to be governed by first order kinetics. Compartment models based on linear differential equation systems, as used in this study, should therefore be adequate. The realism and applicability of ecological compartment models are analysed with respect to completeness of the systems of reservoirs and pathways as well as accuracy in assumed reservoir sizes and exchange rates. By introducing different biospheric reservoirs and transfer mechanisms, important carriers and recipients are identified for the analysis of tritium released to air, land and water. Terrestrial biota and groundwater are shown to be significant both with regard to reservoir sizes and influence on the land-troposphere and land-sea exchange of tritium. Model studies regarding the conversion of HT to HTO in different biospheric reservoirs indicate that an atmospheric release of HT may yield up to 1.7 times the dose commitment obtained after release of the same amount of tritium as HTO. The global collective dose commitment from a tropospheric release of tritium is 0.002-0.004 man.rem per Ci depending on the latitude at the release point. Release to the surface ocean layers gives a ten times lower collective dose. (author)

  19. Amount of trace elements in marine cephalopods

    International Nuclear Information System (INIS)

    Ueda, Taiji; Nakahara, Motokazu; Ishii, Toshiaki; Suzuki, Yuzuru; Suzuki, Hamaji.

    1979-01-01

    For the estimation of internal radiation to human beings, the amounts of Mn, Fe, Cu, Zn, Co and Cs in 5 species of marine cephalopods were determined by atomic absorption spectrophotometry and neutron activation analysis, and then the concentration factors were calculated. The average amount and the concentration factor of the elements in the edible parts (mantle, arms and tentacles) of cephalopods are as follows: 0.14 mg, 2 x 10 2 for Mn, 1.8 mg, 2 x 10 2 for Fe, 2.0 mg, 7 x 10 2 for Cu, 12.2 mg, 1 x 10 3 for Zn, 5.3 μg, 6 x 10 1 for Co and 3.4 μg, 7 for Cs. The amounts of Fe, Co, Cu and Zn in the liver and the branchial heart were much higher than those in the edible parts, although those of Cs and Mn were almost the same. The Co content in the visceral organs of O. Vulgaris showed extremely high value, particularly in the branchial heart. (author)

  20. Airborne engineered nanomaterials in the workplace—a review of release and worker exposure during nanomaterial production and handling processes

    Energy Technology Data Exchange (ETDEWEB)

    Ding, Yaobo [Institute for Work and Health (IST), Universities of Lausanne and Geneva, Route de la Corniche 2, 1066, Epalinges (Switzerland); Kuhlbusch, Thomas A.J. [Institute of Energy and Environmental Technology (IUTA), Air Quality & Sustainable Nanotechnology Unit, Bliersheimer Straße 58-60, 47229 Duisburg (Germany); Centre for Nanointegration (CENIDE), University Duisburg-Essen, Duisburg (Germany); Van Tongeren, Martie; Jiménez, Araceli Sánchez [Centre for Human Exposure Science, Institute of Occupational Medicine (IOM), Research Avenue North, Edinburgh EH14 4AP (United Kingdom); Tuinman, Ilse [TNO, Lange Kleiweg 137, Rijswijk (Netherlands); Chen, Rui [CAS Key Laboratory for Biomedical Effects of Nanomaterials and Nanosafety & CAS Center for Excellence in Nanoscience, National Center for Nanoscience and Technology of China, Beijing 100190 (China); Alvarez, Iñigo Larraza [ACCIONA Infrastructure, Materials Area, Innovation Division, C/Valportillo II 8, 28108, Alcobendas (Spain); Mikolajczyk, Urszula [Nofer Institute of Occupational Medicine, Lodz (Poland); Nickel, Carmen; Meyer, Jessica; Kaminski, Heinz [Institute of Energy and Environmental Technology (IUTA), Air Quality & Sustainable Nanotechnology Unit, Bliersheimer Straße 58-60, 47229 Duisburg (Germany); Wohlleben, Wendel [Dept. Material Physics, BASF SE, Advanced Materials Research, Ludwigshafen (Germany); Stahlmecke, Burkhard [Institute of Energy and Environmental Technology (IUTA), Air Quality & Sustainable Nanotechnology Unit, Bliersheimer Straße 58-60, 47229 Duisburg (Germany); Clavaguera, Simon [NanoSafety Platform, Commissariat à l’Energie Atomique et aux Energies Alternatives (CEA), Univ. Grenoble Alpes, Grenoble, 38054 (France); and others

    2017-01-15

    Highlights: • Release characteristics can be grouped by the type of occupational activities. • Release levels may be linked to process energy. • A better data reporting practice will facilitate exposure assessment. • The results help prioritize industrial processes for human risk assessment. - Abstract: For exposure and risk assessment in occupational settings involving engineered nanomaterials (ENMs), it is important to understand the mechanisms of release and how they are influenced by the ENM, the matrix material, and process characteristics. This review summarizes studies providing ENM release information in occupational settings, during different industrial activities and using various nanomaterials. It also assesses the contextual information — such as the amounts of materials handled, protective measures, and measurement strategies — to understand which release scenarios can result in exposure. High-energy processes such as synthesis, spraying, and machining were associated with the release of large numbers of predominantly small-sized particles. Low-energy processes, including laboratory handling, cleaning, and industrial bagging activities, usually resulted in slight or moderate releases of relatively large agglomerates. The present analysis suggests that process-based release potential can be ranked, thus helping to prioritize release assessments, which is useful for tiered exposure assessment approaches and for guiding the implementation of workplace safety strategies. The contextual information provided in the literature was often insufficient to directly link release to exposure. The studies that did allow an analysis suggested that significant worker exposure might mainly occur when engineering safeguards and personal protection strategies were not carried out as recommended.

  1. Airborne engineered nanomaterials in the workplace—a review of release and worker exposure during nanomaterial production and handling processes

    International Nuclear Information System (INIS)

    Ding, Yaobo; Kuhlbusch, Thomas A.J.; Van Tongeren, Martie; Jiménez, Araceli Sánchez; Tuinman, Ilse; Chen, Rui; Alvarez, Iñigo Larraza; Mikolajczyk, Urszula; Nickel, Carmen; Meyer, Jessica; Kaminski, Heinz; Wohlleben, Wendel; Stahlmecke, Burkhard; Clavaguera, Simon

    2017-01-01

    Highlights: • Release characteristics can be grouped by the type of occupational activities. • Release levels may be linked to process energy. • A better data reporting practice will facilitate exposure assessment. • The results help prioritize industrial processes for human risk assessment. - Abstract: For exposure and risk assessment in occupational settings involving engineered nanomaterials (ENMs), it is important to understand the mechanisms of release and how they are influenced by the ENM, the matrix material, and process characteristics. This review summarizes studies providing ENM release information in occupational settings, during different industrial activities and using various nanomaterials. It also assesses the contextual information — such as the amounts of materials handled, protective measures, and measurement strategies — to understand which release scenarios can result in exposure. High-energy processes such as synthesis, spraying, and machining were associated with the release of large numbers of predominantly small-sized particles. Low-energy processes, including laboratory handling, cleaning, and industrial bagging activities, usually resulted in slight or moderate releases of relatively large agglomerates. The present analysis suggests that process-based release potential can be ranked, thus helping to prioritize release assessments, which is useful for tiered exposure assessment approaches and for guiding the implementation of workplace safety strategies. The contextual information provided in the literature was often insufficient to directly link release to exposure. The studies that did allow an analysis suggested that significant worker exposure might mainly occur when engineering safeguards and personal protection strategies were not carried out as recommended.

  2. Release of Liposomal Contents by Cell-Secreted Matrix Metalloproteinase-9

    Science.gov (United States)

    Banerjee, Jayati; Hanson, Andrea J.; Gadam, Bhushan; Elegbede, Adekunle I.; Tobwala, Shakila; Ganguly, Bratati; Wagh, Anil; Muhonen, Wallace W.; Law, Benedict; Shabb, John B.; Srivastava, D. K.; Mallik, Sanku

    2011-01-01

    Liposomes have been widely used as a drug delivery vehicle and currently, more than 10 liposomal formulations are approved by the Food and Drug Administration for clinical use. However, upon targeting, the release of the liposome-encapsulated contents is usually slow. We have recently demonstrated that contents from appropriately-formulated liposomes can be rapidly released by the cancer-associated enzyme matrix metalloproteinase-9 (MMP-9). Herein, we report our detailed studies to optimize the liposomal formulations. By properly selecting the lipopeptide, the major lipid component and their relative amounts, we demonstrate that the contents are rapidly released in the presence of cancer-associated levels of recombinant human MMP-9. We observed that the degree of lipid mismatch between the lipopepides and the major lipid component profoundly affects the release profiles from the liposomes. By utilizing the optimized liposomal formulations, we also demonstrate that cancer cells (HT-29) which secrete low levels of MMP-9 failed to release significant amount of the liposomal contents. Metastatic cancer cells (MCF7) secreting high levels of the enzyme rapidly release the encapsulated contents from the liposomes. PMID:19601658

  3. Physical protection of small amounts of nuclear material or contaminated parts

    International Nuclear Information System (INIS)

    Zipper, R.

    2002-01-01

    In July 2001 an incident was recognized where a worker occupied with decontamination of structures in a shut down reprocessing plant for spent fuel illegally removed a small amount of radioactive material from the facility site. The investigations exhibited that he brought this material to the apartment of his partner in life and she incorporated significantly α-activity in the form of plutonium. Immediately after the incident was discovered the supervisory authorities and the operating company of the facility took action to minimize the harms to third parties arising from the radioactive material released and to prevent a similar event to occur. As the overall inventory of radioactive material in the shut down facility at the time the theft occurred was below the limit where measures of physical protection are required by the German regulatory work discussions were raised on consequences to be drawn from this incident to close this obvious gap. The German Federal Ministry for Environment, Nature Protection and Reactor Safety (BMU) as the superior competent authority therefore ordered GRS to draft a set of fundamental requirements for future rules to make a repetition of the initiating incident unlikely. Further discussions of the authorities involved on supplementary rules and guidelines aiming to better protect small amounts of radioactive material from being illegally removed out of nuclear facilities and laboratories are based on these fundamentals defined by GRS but not yet finished. (orig.)

  4. Drug release kinetic analysis and prediction of release data via polymer molecular weight in sustained release diltiazem matrices.

    Science.gov (United States)

    Adibkia, K; Ghanbarzadeh, S; Mohammadi, G; Khiavi, H Z; Sabzevari, A; Barzegar-Jalali, M

    2014-03-01

    This study was conducted to investigate the effects of HPMC (K4M and K100M) as well as tragacanth on the drug release rate of diltiazem (DLTZ) from matrix tablets prepared by direct compression method.Mechanism of drug transport through the matrices was studied by fitting the release data to the 10 kinetic models. 3 model independent parameters; i. e., mean dissolution time (MDT), mean release rate (MRR) and release rate efficacy (RE) as well as 5 time point approaches were established to compare the dissolution profiles. To find correlation between fraction of drug released and polymer's molecular weight, dissolution data were fitted into two proposed equations.All polymers could sustain drug release up to 10 h. The release data were fitted best to Peppas and Higuchi square root kinetic models considering squared correlation coefficient and mean percent error (MPE). RE and MRR were decreased when polymer to drug ratio was increased. Conversely, t60% was increased with raising polymer /drug ratio. The fractions of drug released from the formulations prepared with tragacanth were more than those formulated using the same amount of HPMC K4M and HPMC K100M.Preparation of DLTZ matrices applying HPMCK4M, HPMC K100M and tragacanth could effectively extend the drug release. © Georg Thieme Verlag KG Stuttgart · New York.

  5. Predicting hydrocarbon release from soil

    International Nuclear Information System (INIS)

    Poppendieck, D.; Loehr, R.C.

    2002-01-01

    'Full text:' The remediation of hazardous chemicals from soils can be a lengthy and costly process. As a result, recent regulatory initiatives have focused on risk-based corrective action (RBCA) approaches. Such approaches attempt to identify the amount of chemical that can be left at a site with contaminated soil and still be protective of human health and the environment. For hydrocarbons in soils to pose risk to human heath and the environment, the hydrocarbons must be released from the soil and accessible to microorganisms, earthworms, or other higher level organisms. The sorption of hydrocarbons to soil can reduce the availability of the hydrocarbon to receptors. Typically in soils and sediments, there is an initial fast release of a hydrocarbon from the soil to the aqueous phase followed by a slower release of the remaining hydrocarbon to the aqueous phase. The rate and extent of slow release can influence aqueous hydrocarbon concentrations and the fate and transport of hydrocarbons in the subsurface. Once the fast fraction of the chemical has been removed from the soil, the remaining fraction of a chemical may desorb at a rate that natural mechanisms can attenuate the released hydrocarbon. Hence, active remediation may be needed only until the fast fraction has been removed. However, the fast fraction is a soil and chemical specific parameter. This presentation will present a tier I type protocol that has been developed to quickly estimate the fraction of hydrocarbons that are readily released from the soil matrix to the aqueous phase. Previous research in our laboratory and elsewhere has used long-term desorption (four months) studies to determine the readily released fraction. This research shows that a single short-term (less than two weeks) batch extraction procedure provides a good estimate of the fast released fraction derived from long-term experiments. This procedure can be used as a tool to rapidly evaluate the release and bioavailability of

  6. Fluoride release and recharge behavior of a nano-filled resin-modified glass ionomer compared with that of other fluoride releasing materials.

    Science.gov (United States)

    Mitra, Sumita B; Oxman, Joe D; Falsafi, Afshin; Ton, Tiffany T

    2011-12-01

    To compare the long-term fluoride release kinetics of a novel nano-filled two-paste resin-modified glass-ionomer (RMGI), Ketac Nano (KN) with that of two powder-liquid resin-modified glass-ionomers, Fuji II LC (FLC) and Vitremer (VT) and one conventional glass-ionomer, Fuji IX (FIX). Fluoride release was measured in vitro using ion-selective electrodes. Kinetic analysis was done using regression analysis and compared with existing models for GIs and compomers. In a separate experiment the samples of KN and two conventional glass-ionomers, FIX and Ketac Molar (KM) were subjected to a treatment with external fluoride source (Oral-B Neutra-Foam) after 3 months of fluoride release and the recharge behavior studied for an additional 7-day period. The cumulative amount of fluoride released from KN, VT and FLC and the release profiles were statistically similar but greater than that for FIX at P coating of KN with its primer and of DY with its adhesive did not significantly alter the fluoride release behavior of the respective materials. The overall rate for KN was significantly higher than for the compomer DY. DY showed a linear rate of release vs. t and no burst effect as expected for compomers. The nanoionomer KN showed fluoride recharge behavior similar to the conventional glass ionomers FIX and KM. Thus, it was concluded that the new RMGI KN exhibits fluoride ion release behavior similar to typical conventional and RMGIs and that the primer does not impede the release of fluoride.

  7. Biological significance of soluble IL-2 receptor

    Directory of Open Access Journals (Sweden)

    Calogero Caruso

    1993-01-01

    Full Text Available A NUMBER of receptors for growth factors and differentiation antigens have been found to be secreted or released by cells. Following mononuclear cell (MNC activation and interleukin-2 receptor (IL-2R expression, a soluble form of the Alpha;-chain of IL-2R (sIL-2R is released. The sIL-2R has been shown to be present in the culture supernatants of activated MNCs as well as in normal sera and, in higher amounts, in sera from subjects affected by several diseases including neoplastic, infectious and autoimmune ones, and in sera from transplanted patients suffering allograft rejection. The blood sIL-2R levels depend on the number of producing cells and the number of molecules per cell, so that sIL-2R blood values may represent an index of the number and the functional state of producing cells, both normal and neoplastic. Thus, monitoring of the immune system, mostly T-cells and haematological malignancies might be targets for the measurement of sIL-2R. Since many conditions may influence sIL-2R production, little diagnostic use may result from these measurements. However, since blood sIL-2R levels may correlate with disease progression and/or response to therapy, their measurement may be a useful index of activity and extent of disease. The precise biological role of the soluble form of the IL-2R is still a matter of debate. However, we know that increased sIL-2R levels may be observed in association with several immunological abnormalities and that sIL-2R is able to bind IL-2. It is conceivable then that in these conditions the excess sIL-2R released in vivo by activated lymphoid cells or by neoplastic cells may somehow regulate IL-2-dependent processes. On the other hand, it cannot exclude that sIL-2R is a by-product without biological significance. Finally, it is puzzling that in many conditions in which an increase of blood sIL-2R values has been observed, MNCs display a decreased in vitro capacity to produce sIL-2R. These seemingly contrasting

  8. Design and evaluation of lornoxicam bilayered tablets for biphasic release

    Directory of Open Access Journals (Sweden)

    Songa Ambedkar Sunil

    2012-12-01

    Full Text Available The objective of the present investigation was to develop bilayered tablets of lornoxicam to achieve biphasic release pattern. A bilayered tablet, consisting of an immediate and controlled release layer, was prepared by direct compression technique. The controlled release effect was achieved by using various hydrophilic natural, semi synthetic and synthetic controlled release polymers such as xanthan gum, hydroxypropyl methylcellulose (HPMC and polyethylene oxide (PEO to modulate the release of the drug. The in vitro drug release profiles showed the biphasic release behavior in which the immediate release (IR layer containing the lornoxicam was released within 15 minutes, whereas the controlled release (CR layer controlled the drug release for up to 24 h. All the bilayered tablets formulated have followed the zero order release with non-Fickian diffusion controlled release mechanism after the initial burst release. FTIR studies revealed that there was no interaction between the drug and polymers used in the study. Statistical analysis (ANOVA showed no significant difference in the cumulative amount of drug release after 15 min, but significant difference (p O objetivo do presente trabalho foi desenvolver comprimidos bicamada de lornoxicam para atingir padrão de liberação bifásica. Preparou-se, por compressão direta, comprimido bicamada, consistindo de uma camada de liberação imediata e uma de liberação controlada. A liberação controlada foi obtida pelo uso de vários polímeros naturais hidrofílicos, semi-sintéticos e sintéticos, tais como goma xantana, hidroxipropilmetil celulose (HPMC e óxido de polietileno (PEO para modular a liberação do fármaco. Os perfis de liberação in vitro mostraram comportamento bifásico em que a camada de liberação imediata (IR contendo lornoxicam foi liberada em 15 minutos, enquanto a camada de liberação controlada (CR liberou o fármaco em mais de 24 horas, Todos os comprimidos bicamada

  9. Do CAD/CAM dentures really release less monomer than conventional dentures?

    Science.gov (United States)

    Steinmassl, Patricia-Anca; Wiedemair, Verena; Huck, Christian; Klaunzer, Florian; Steinmassl, Otto; Grunert, Ingrid; Dumfahrt, Herbert

    2017-06-01

    Computer-aided design (CAD)/computer-aided manufacturing (CAM) dentures are assumed to have more favourable material properties than conventionally fabricated dentures, among them a lower methacrylate monomer release. The aim of this study was to test this hypothesis. CAD/CAM dentures were generated from ten different master casts by using four different CAD/CAM systems. Conventional, heat-polymerised dentures served as control group. Denture weight and volume were measured; the density was calculated, and the denture surface area was assessed digitally. The monomer release after 7 days of water storage was measured by high-performance liquid chromatography. Whole You Nexteeth and Wieland Digital Dentures had significantly lower mean volume and weight than conventional dentures. Baltic Denture System and Whole You Nexteeth had a significantly increased density. Baltic Denture System had a significantly smaller surface area. None of the CAD/CAM dentures released significantly less monomer than the control group. All tested dentures released very low amounts of methacrylate monomer, but not significantly less than conventional dentures. A statistically significant difference might nevertheless exist in comparison to other, less recommendable denture base materials, such as the frequently used autopolymerising resins. CAD/CAM denture fabrication has numerous advantages. It enables the fabrication of dentures with lower resin volume and lower denture weight. Both could increase the patient comfort. Dentures with higher density might exhibit more favourable mechanical properties. The hypothesis that CAD/CAM dentures release less monomer than conventional dentures could, however, not be verified.

  10. Metal release from simulated fixed orthodontic appliances.

    Science.gov (United States)

    Hwang, C J; Shin, J S; Cha, J Y

    2001-10-01

    Most orthodontic appliances and archwires are stainless steel or nickel-titanium (NiTi) alloys that can release metal ions, with saliva as the medium. To measure metal released from the fixed orthodontic appliances currently in use, we fabricated simulated fixed orthodontic appliances that corresponded to half of the maxillary arch and soaked them in 50 mL of artificial saliva (pH 6.75 +/- 0.15, 37 degrees C) for 3 months. We used brackets, tubes, and bands made by Tomy (Tokyo, Japan). Four groups were established according to the appliance manufacturer and the type of metal in the .016 x .022-in archwires. Groups A and B were stainless steel archwires from Ormco (Glendora, Calif) and Dentaurum (Ispringen, Germany), respectively, and groups C and D were both NiTi archwires with Ormco's copper NiTi and Tomy's Bioforce sentalloy, respectively. Stainless steel archwires were heat treated in an electric furnace at 500 degrees C for 1 minute and quenched in water. We measured the amount of metal released from each group by immersion time. Our conclusions were as follows: (1) there was no increase in the amount of chromium released after 4 weeks in group A, 2 weeks in group B, 3 weeks in group C, and 8 weeks in group D; (2) there was no increase in the amount of nickel released after 2 weeks in group A, 3 days in group B, 7 days in group C, and 3 weeks in group D; and (3) there was no increase in the amount of iron released after 2 weeks in group A, 3 days in group B, and 1 day in groups C and D. In our 3-month-long investigation, we saw a decrease in metal released as immersion time increased.

  11. In vitro evaluation of extemporaneously compounded slow-release capsules containing morphine sulfate or oxycodone hydrochloride.

    Science.gov (United States)

    Glowiak, Dana L; Green, Julie L; Bowman, Bill J

    2005-01-01

    The in vitro performance of extemporaneously compounded morphine sulfate and oxycodone hydrochloride slow-release capsules was evaluated. Capsules containing varying amoutns of morphine sulfate (15, 60, 200 mg) or oxycodone hydrochloride (10, 80, 200 mg) were prepared and provided by a Phoenix, Arizona, pharmacy. The capsules also contained 40% Methocel E4M Premium to slow the release of their active ingredient and sufficient lactose to fill the capsules. Three batches of each capsule strength were prepared, and replicates from each batch were evlauated using United Stated Pharmacopeia dissolution apparatus II. Samples were taken at regular time intervals over 24 hours. After 1 hour the pH of the dissolution medium was adjusted form 1.2 to 4.0, and after 2 hours the pH was adjusted to 6.8. The amount of drug released at each time point was determined spectrophotometrically. The compounded capsules released 14% to 23%, 67% to 85% and 93% to 98% of their active ingredient after 0.5, 4 and 12 hours, respectively. The relative standard deviations between the replicates from each batch were less than 10% for most time points. The percent of drug released over the first 4 hours was linear (r squared = 0.9409-0.9999) when plotted versus time 1/2, indicating adherence to the simplified Higuchi model. Statistical analysis of the Higuchi dissolution constants indicated a significant difference (P less than 0.05) between batch No.3 and the other two batches of 200-mg oxycodone hydrochloride capsules. There was also a statistical difference between most of the Higuchi dissolution constants for the different-strength slow-release capsules and most slow-release capsules and equivalent strength controlled-release manufactured tablets (P less than 0.05). Using 40% Methocel E4M Premium slowed the release of morphine sulfate and oxycodone hydrochloride from extemporaneously compounded capsules. The in vitro performance of the slow-release capsules showed little intrabatch variation

  12. Toxics Release Inventory (TRI)

    Data.gov (United States)

    U.S. Environmental Protection Agency — The Toxics Release Inventory (TRI) is a dataset compiled by the U.S. Environmental Protection Agency (EPA). It contains information on the release and waste...

  13. Polarographic determination of trace amounts of thorium

    Energy Technology Data Exchange (ETDEWEB)

    Zaofan Zhao; Xiaohua Cai; Peibiao Li; Handong Yang

    1986-07-01

    A sensitive linear-sweep polarographic method for the determination of thorium is described. It is based on the thorium complex with Xylidyl Blue I (XBI) in a medium containing ethylenediamine, 1, 10-phenanthroline, oxalic acid and ninhydrin, at pH 10.5-11.5. The complex has been proved to be Th(XBI)/sub 2/, with log ..beta..'=9.6. The method can be used to determine trace amounts of thorium over the range 3.5x10/sup -8/-3x10/sup -6/M. The detection limit is 1x10/sup -8/M. A solvent extraction procedure is necessary to eliminate interference from several cations. The method has been applied to determination of traces of thorium in minerals, with good results.

  14. Rab3A Inhibition of Ca2+ -Dependent Dopamine Release From PC12 Cells Involves Interaction With Synaptotagmin I.

    Science.gov (United States)

    Dai, Zhipan; Tang, Xia; Chen, Jia; Tang, Xiaochao; Wang, Xianchun

    2017-11-01

    Rab3 and synaptotagmin have been suggested to play important roles in the regulation of neurotransmitter release and, however, the molecular mechanism has not been completely clear. Here, we studied the effects of Rab3A and synaptotagmin I (Syt I) on dopamine release using PC12 cells as a model system. Rab3A was demonstrated to have effects on both Ca 2+ -independent and Ca 2+ -dependent dopamine releases from the PC12 cells. Application of Rab3A (up to 2500 nM) gradually decreased the amount of Ca 2+ -dependently released dopamine, indicating that Rab3A is a negative modulator that was further supported by the increase in dopamine release caused by Rab3A knockdown. Syt I knockdown weakened the Ca 2+ -dependent dopamine release, suggesting that Syt I plays a positive regulatory role in the cellular process. Treatment of the Syt I-knocked down PC12 cells with Rab3A further decreased Ca 2+ -dependent dopamine release and, however, the decrease magnitude was significantly reduced compared with that before Syt I knockdown, thus for the first time demonstrating that the inhibitory effect of Rab3A on Ca 2+ -dependent dopamine release involves the interaction with Syt I. This work has shed new light on the molecular mechanism for Rab3 and synaptotamin regulation of neurotransmitter release. J. Cell. Biochem. 118: 3696-3705, 2017. © 2017 Wiley Periodicals, Inc. © 2017 Wiley Periodicals, Inc.

  15. Excitatory and inhibitory effects of prolactin release activated by nerve stimulation in rat anterior pituitary

    Directory of Open Access Journals (Sweden)

    Gao Li-Zhi

    2009-12-01

    Full Text Available Abstract Background A series of studies showed the presence of substantial amount of nerve fibers and their close relationship with the anterior pituitary gland cells. Our previous studies have suggested that aside from the classical theory of humoral regulation, the rat anterior pituitary has direct neural regulation on adrenocorticotropic hormone release. In rat anterior pituitary, typical synapses are found on every type of the hormone-secreting cells, many on lactotrophs. The present study was aimed at investigating the physiological significance of this synaptic relationship on prolactin release. Methods The anterior pituitary of rat was sliced and stimulated with electrical field in a self-designed perfusion chamber. The perfusate was continuously collected in aliquots and measured by radioimmunoassay for prolactin levels. After statistic analysis, differences of prolactin concentrations within and between groups were outlined. Results The results showed that stimulation at frequency of 2 Hz caused a quick enhancement of prolactin release, when stimulated at 10 Hz, prolactin release was found to be inhibited which came slower and lasted longer. The effect of nerve stimulation on prolactin release is diphasic and frequency dependent. Conclusions The present in vitro study offers the first physiological evidence that stimulation of nerve fibers can affect prolactin release in rat anterior pituitary. Low frequency stimulation enhances prolactin release and high frequency mainly inhibits it.

  16. Effect of micropatterning induced surface hydrophobicity on drug release from electrospun cellulose acetate nanofibers

    Science.gov (United States)

    Adepu, Shivakalyani; Gaydhane, Mrunalini K.; Kakunuri, Manohar; Sharma, Chandra S.; Khandelwal, Mudrika; Eichhorn, Stephen J.

    2017-12-01

    Sustained release and prevention of burst release for low half-life drugs like Diclofenac sodium is crucial to prevent drug related toxicity. Electrospun nanofibers have emerged recently as potential carrier materials for controlled and sustained drug release. Here, we present a facile method to prevent burst release by tuning the surface wettability through template assisted micropatterning of drug loaded electrospun cellulose acetate (CA) nanofibers. A known amount of drug (Diclofenac sodium) was first mixed with CA and then electrospun in the form of a nanofabric. This as-spun network was hydrophilic in nature. However, when electrospinning was carried out through non-conducting templates, viz nylon meshes with 50 and 100 μm size openings, two kinds of hydrophobic micro-patterned CA nanofabrics were produced. In vitro transdermal testing of our nanofibrous mats was carried out; these tests were able to show that it would be possible to create a patch for transdermal drug release. Further, our results show that with optimized micro-patterned dimensions, a zero order sustained drug release of up to 12 h may be achieved for the transdermal system when compared to non-patterned samples. This patterning caused a change in the surface wettability, to a hydrophobic surface, resulting in a controlled diffusion of the hydrophilic drug. Patterning assisted in controlling the initial burst release, which is a significant finding especially for low half-life drugs.

  17. Stimuli responsive nanomaterials for controlled release applications

    KAUST Repository

    Li, Song; Li, Wengang; Khashab, Niveen M.

    2012-01-01

    applications. Stimuli-responsive nanomaterials guarantee the controlled release of cargo to a given location, at a specific time, and with an accurate amount. In this review, we have combined the major stimuli that are currently used to achieve the ultimate

  18. Studies on renin release in vitro

    DEFF Research Database (Denmark)

    Skøtt, O

    1989-01-01

    1) Measurements of renin secretion from single arterioles at time intervals down to 20 seconds showed that the renin secretion is episodic, the amount of renin released during each episode corresponding to the estimated content of one secretory granule. 2) A decrease in osmolality elicits episodi...

  19. DETERMINATION OF METAL IONS RELEASED BY STAINLESS ...

    African Journals Online (AJOL)

    The amounts of cobalt, iron, manganese, nickel and chromium ions released from new and reused stainless steel arch bar used for maxillomandibular fixation was determined in Hank's solutions of different hydrogen and chloride ions concentrations, whole blood serum and phosphate buffered saline (PBS) in vitro, over a ...

  20. Calcitonin gene-related peptide and somatostatin releases correlated with the area under the lafutidine concentration-time curve in human plasma.

    Science.gov (United States)

    Ikawa, K; Shimatani, T; Azuma, Y; Inoue, M; Morikawa, N

    2006-08-01

    To examine the effects of the histamine H(2)-receptor antagonist, lafutidine, at clinical dosage (10 mg tablet after a standardized meal) on plasma levels of the gastrointestinal peptides, calcitonin gene-related peptide (CGRP), somatostatin and gastrin. Six healthy male volunteers ate a standardized meal, and received either lafutidine orally at a dose of 10 mg or water only (control). Blood samples were taken before and up to 4 h after the drug administration. Plasma lafutidine concentrations were determined by high pressure liquid chromatography. Pharmacokinetic analysis of lafutidine was performed using one-compartmental model. The levels of immunoreactive substances of plasma CGRP, somatostatin and gastrin were measured by enzyme immunoassay, and the amount of peptide release was calculated by the trapezoidal method. Lafutidine significantly increased plasma CGRP levels at 1, 1.5, 2.5 and 4 h and the total amount of CGRP release (192 +/- 14.0 pg.h/mL) compared with the control group (128 +/- 21.5 pg.h/mL). Lafutidine significantly increased the plasma somatostatin levels at 1 and 1.5 h, and the total amount of somatostatin released (107 +/- 18.2 pg.h/mL) compared with the control (78.4 +/- 7.70 pg.h/mL). The area under the drug concentration-time curve (AUC) from 0 to 4 h after administration correlated well with the Delta-CGRP and Delta-somatostatin release but not with total amount of gastrin released. However, plasma gastrin levels were significantly elevated at 1.5 h after drug administration. Lafutidine at clinical dosage increases plasma CGRP and the somatostatin. The amounts released correlated with the AUC of lafutidine in humans. These results suggest that the increased release of CGRP and somatostatin may contribute to its gastroprotective and anti-acid secretory effect.

  1. Employment of the porous particles for preparation of the capsules containing aspirin and drug release property

    International Nuclear Information System (INIS)

    Hosoi, Fumio; Makuuchi, Keizo; Saito, Kenji; Koishi, Masumi.

    1985-01-01

    Polymer-coated porous particles containing aspirin as a drug were prepared and the rate of release of aspirin was studied. The impregnation of aspirin was carried out by post-graft polymerization, where methyl methacrylate or methacrylic acid was treated with porous particles, pre-irradiated with γ-ray from 60 Co, in the presence of aspirin. Release of aspirin from modified particles was tested with 50 % methanol solution and/or pH 5.2 buffer solution of acetic acid. The amount of aspirin released from capsules increased with time and reached a constant values after 140 h. The amount of aspirin absorbed in porous particles was increased with graft polymerization. In addition, absorption of aspirin in porous particles was significantly enhanced by treating the particle surface with TiO 2 before irradiation. The amount of aspirin released was linearly to the square root of time. It was concluded that the diffusion of aspirin through the polymer matrix was the rate limiting step. (author)

  2. Optimization of sustained release aceclofenac microspheres using response surface methodology

    Energy Technology Data Exchange (ETDEWEB)

    Deshmukh, Rameshwar K.; Naik, Jitendra B., E-mail: jitunaik@gmail.com

    2015-03-01

    Polymeric microspheres containing aceclofenac were prepared by single emulsion (oil-in-water) solvent evaporation method using response surface methodology (RSM). Microspheres were prepared by changing formulation variables such as the amount of Eudragit® RS100 and the amount of polyvinyl alcohol (PVA) by statistical experimental design in order to enhance the encapsulation efficiency (E.E.) of the microspheres. The resultant microspheres were evaluated for their size, morphology, E.E., and in vitro drug release. The amount of Eudragit® RS100 and the amount of PVA were found to be significant factors respectively for determining the E.E. of the microspheres. A linear mathematical model equation fitted to the data was used to predict the E.E. in the optimal region. Optimized formulation of microspheres was prepared using optimal process variables setting in order to evaluate the optimization capability of the models generated according to IV-optimal design. The microspheres showed high E.E. (74.14 ± 0.015% to 85.34 ± 0.011%) and suitably sustained drug release (minimum; 40% to 60%; maximum) over a period of 12 h. The optimized microspheres formulation showed E.E. of 84.87 ± 0.005 with small error value (1.39). The low magnitudes of error and the significant value of R{sup 2} in the present investigation prove the high prognostic ability of the design. The absence of interactions between drug and polymers was confirmed by Fourier transform infrared (FTIR) spectroscopy. Differential scanning calorimetry (DSC) and X-ray powder diffractometry (XRPD) revealed the dispersion of drug within microspheres formulation. The microspheres were found to be discrete, spherical with smooth surface. The results demonstrate that these microspheres could be promising delivery system to sustain the drug release and improve the E.E. thus prolong drug action and achieve the highest healing effect with minimal gastrointestinal side effects. - Highlights: • Aceclofenac microspheres

  3. Energy Release in Solar Flares,

    Science.gov (United States)

    1982-10-01

    Plasma Research, Stanford University P. Kaufmanu CRAA/CNPq -Conseiho lacional de Desenvolvimento Cientifico e Tecnologico, Slo Paulo, SP, Brasil D.F...three phases of energy release in solar flares (Sturrock, 1980). However, a recent article by Feldman e a.. (1982) points to a significant

  4. Tritium behavior intentionally released in the room

    International Nuclear Information System (INIS)

    Kobayashi, K.; Hayashi, T.; Iwai, Y.; Yamanishi, T.; Willms, R. S.; Carlson, R. V.

    2008-01-01

    To construct a fusion reactor with high safety and acceptability, it is necessary to establish and to ensure tritium safe handling technology. Tritium should be well-controlled not to be released to the environment excessively and to prevent workers from excess exposure. It is especially important to grasp tritium behavior in the final confinement area, such as the room and/or building. In order to obtain data for actual tritium behavior in a room and/or building, a series of intentional Tritium Release Experiments (TREs) were planned and carried out within a radiologically controlled area (main cell) at Tritium System Test Assembly (TSTA) in Los Alamos National Laboratory (LANL) under US-JAPAN collaboration program. These experiments were carried out three times. In these experiments, influence of a difference in the tritium release point and the amount of hydrogen isotope for the initial tritium behavior in the room were suggested. Tritium was released into the main cell at TSTA/LANL. The released tritium reached a uniform concentration about 30 - 40 minutes in all the experiments. The influence of the release point and the amount of hydrogen isotope were not found to be important in these experiments. The experimental results for the initial tritium behavior in the room were also simulated well by the modified three-dimensional eddy flow analysis code FLOW-3D. (authors)

  5. Relationship between insulin release and 65zinc efflux from rat pancreatic islets maintained in tissue culture

    International Nuclear Information System (INIS)

    Formby, B.; Schmid-Formby, F.; Grodsky, G.M.

    1984-01-01

    In short-term batch-incubation or perfusion experiments, we studied insulin release and associated 65 Zn efflux from rat pancreatic islets loaded with 65 Zn by 24-h tissue culture in low-glucose medium. The fractional basal insulin release and 65 Zn efflux were 0.4% and 3% of total content/h/islet, respectively. Thus, basal 65 Zn efflux was much greater than that to be accounted for if zinc was released proportionally with insulin release only; extragranular zinc flux was suggested. Two millimolar glucose, with or without 1 mM 3-isobutyl-1-methylxanthine (IBMX), affected neither insulin release nor associated 65 Zn efflux. Twenty-five millimolar glucose produced a significant threefold increase in insulin release above baseline, but somewhat decreased 65 Zn efflux at marginal significance. Glucose (25 mM) plus 1 mM IBMX provoked a high increase in insulin release and an associated 30% increase in fractional 65 Zn efflux over basal. Calculations based on previous estimations of 65 Zn distribution and equilibrium with islet zinc indicated that molar zinc efflux was more than sufficient to account for a 2-zinc-insulin hexamer. L-Leucine (2 or 20 mM) plus 1 mM IBMX caused far greater 65 Zn efflux for the amount of insulin released, indicating additional 65 Zn mobilization not directly related to insulin secretion. To evaluate 65 Zn efflux during inhibited insulin secretion, batch incubations were performed in 100% D 2 O or at 27 degrees C, conditions that inhibited insulin release stimulated by high glucose plus IBMX. These agents decreased the 65 Zn efflux far below the basal value (35% and 50%, respectively) and greater than could be accounted for by the attendent inhibition of insulin secretion.(ABSTRACT TRUNCATED AT 250 WORDS)

  6. Fission-product release during accidents

    International Nuclear Information System (INIS)

    Hunt, C.E.L.; Cox, D.S.

    1991-09-01

    One of the aims when managing a reactor accident is to minimize the release of radioactive fission products. Release is dependent not only on the temperature, but also on the partial pressure of oxygen. Strongly oxidizing atmospheres, such as those that occurred during the Chernobyl accident, released semi-volatile elements like ruthenium, which has volatile oxides. At low temperatures, UO 2 oxidization to U 3 O 8 can result in extensive breakup of the fuel, resulting in the release of non-volatile fission products as aerosols. Under less oxidizing conditions, when hydrogen accumulates from the zirconium-water reaction, the resulting low oxygen partial pressure can significantly reduce these reactions. At TMI-2, only the noble gases and volatile fission products were released in significant quantities. A knowledge of the effect of atmosphere as well as temperature on the release of fission products from damaged reactor cores is therefore a useful, if not necessary, component of information required for accident management

  7. 76 FR 59138 - Medicare Program; Medicare Appeals; Adjustment to the Amount in Controversy Threshold Amounts for...

    Science.gov (United States)

    2011-09-23

    ... Administrative Law Judge (ALJ) hearings and judicial review under the Medicare appeals process. The adjustment to the AIC threshold amounts will be effective for requests for ALJ hearings and judicial review filed on... $1,350 for judicial review. DATES: Effective Date: This notice is effective on January 1, 2012. FOR...

  8. 75 FR 58407 - Medicare Program; Medicare Appeals; Adjustment to the Amount in Controversy Threshold Amounts for...

    Science.gov (United States)

    2010-09-24

    ... Administrative Law Judge (ALJ) hearings and judicial review under the Medicare appeals process. The adjustment to the AIC threshold amounts will be effective for requests for ALJ hearings and judicial review filed on... judicial review. DATES: Effective Date: This notice is effective on January 1, 2011. FOR FURTHER...

  9. 78 FR 59702 - Medicare Program; Medicare Appeals: Adjustment to the Amount in Controversy Threshold Amounts for...

    Science.gov (United States)

    2013-09-27

    ... Administrative Law Judge (ALJ) hearings and judicial review under the Medicare appeals process. The adjustment to the AIC threshold amounts will be effective for requests for ALJ hearings and judicial review filed on... ALJ hearings and $1,430 for judicial review. DATES: This notice is effective on January 1, 2014. FOR...

  10. 77 FR 59618 - Medicare Program; Medicare Appeals; Adjustment to the Amount in Controversy Threshold Amounts for...

    Science.gov (United States)

    2012-09-28

    ... Administrative Law Judge (ALJ) hearings and judicial review under the Medicare appeals process. The adjustment to the AIC threshold amounts will be effective for requests for ALJ hearings and judicial review filed on... $1,400 for judicial review. Effective Date: This notice is effective on January 1, 2013. FOR FURTHER...

  11. Chronic cigarette smoking enhances spontaneous release of tumour necrosis factor-α from alveolar macrophages of rats

    Directory of Open Access Journals (Sweden)

    G. P. Pessina

    1993-01-01

    Full Text Available Some biological effects of chronic cigarette smoking (two cigarettes for 2 h, daily for 4 months in rats were evaluated. During the smoking period, body weight of smoker rats was always significantly lower than that of control rats. Immediately after the last smoking session the carboxyhaemoglobin concentration in the blood was about 8.5% and the polymorphonuclear cells in the bronchoalveolar fluid increased significantly. At the same time, enzymatic analyses on the supernatants of bronchoalveolar fluid revealed a significant increase of β-glucuronidase in the smoker group. Alveolar macrophages, collected 0, 8 and 24 h after the last smoking session, significantly increased the generation of superoxide anion and, after incubation for 24 h at 37° C in a humidified atmosphere, released significantly high amounts of TNF-α. When challenged with lipopolysaccharide, alveolar macrophages of smoker rats released much more TNF-α but, in such a case, TNF-α release was about one half of that observed in the control group. Peritoneal macrophages of both control and smoker rats were unable either to generate high levels of superoxide anion or to release significant amounts of TNF-α. The results clearly demonstrated the activated state of alveolar macrophages and the resting state of peritoneal macrophages.

  12. Thermoresponsive latexes for fragrance encapsulation and release.

    Science.gov (United States)

    Popadyuk, N; Popadyuk, A; Kohut, A; Voronov, A

    2016-04-01

    To synthesize cross-linked latex particles protecting the encapsulated fragrance at ambient temperatures and facilitating the release of cargo at the temperature of the surface of the skin that varies in different regions of the body between 33.5 and 36.9°C. Poly(stearyl acrylate) (PSA), a polymer with long crystallizable alkyl side chains (undergoes order-disorder transitions at 45°C), was chosen as the main component of the polymer particles. As a result, new thermoresponsive polymer particles for fragrance encapsulation were synthesized and characterized, including assessing the performance of particles in triggered release by elevated temperature. To obtain network domains of various crystallinity, stearyl acrylate was copolymerized with dipropylene glycol acrylate caprylate (DGAC) (comonomer) in the presence of a dipropylene glycol diacrylate sebacate (cross-linker) using the miniemulsion process. Comonomers and a cross-linker were mixed directly in a fragrance during polymerization. Fragrance release was evaluated at 25, 31, 35 and 39°C to demonstrate a new material potential in personal/health care skin-related applications. Particles protect the fragrance from evaporation at 25°C. The fragrance release rate gradually increases at 31, 35 and 39°C. Two slopes were found on release plots. The first slope corresponds to a rapid fragrance release. The second slope indicates a subsequent reduction in the release rate. Crystalline-to-amorphous transition of PSA triggers the release of fragrances from cross-linked latex particles at elevated temperatures. The presence of the encapsulated fragrance, as well as the inclusion of amorphous fragments in the polymer network, reduces the particle crystallinity and enhances the release. Release profiles can be tuned by temperature and controlled by the amount of loaded fragrance and the ratio of comonomers in the feed mixture. © 2015 Society of Cosmetic Scientists and the Société Française de Cosmétologie.

  13. The synthesis and application involving regulation of the insoluble drug release from mesoporous silica nanotubes

    International Nuclear Information System (INIS)

    Li, Jia; Wang, Yan; Zheng, Xin; Zhang, Ying; Sun, Changshan; Gao, Yikun; Jiang, Tongying; Wang, Siling

    2015-01-01

    Highlights: • Mesoporous silica nanotubes (SNT) were synthesized by using CNT as hard template, and the formation of the SNT shows that CTAB played a significant effect on the coating process. • The tube mesoporous silica materials which were seldom reported were applied in the drug delivery system to improve the loading amount and the drug dissolution. • The release rate could be controlled by the gelatin layer on the silica surface and the mechanism was illustrated. - Abstract: Mesoporous silica nanotubes (SNT) were synthesized using hard template carbon nanotubes (CNT) with the aid of cetyltrimethyl ammonium bromide (CTAB) in a method, which was simple and inexpensive. Scanning electron microscopy, transmission electron microscopy and specific surface area analysis were employed to characterize the morphology and structure of SNT, and the formation mechanism of SNT was also examined by Fourier transform infrared spectroscopy. There are few published reports of the mesoporous SNT with large specific surface area applied in the drug delivery systems to improve the amount of drug loading. In addition, the structure of SNT allows investigators to control the drug particle size in the pore channels and significantly increase the drug dissolution rate. The insoluble drug, cilostazol, was chosen as a model drug to be loaded into SNT and we developed a simple and efficient method for regulating the drug release by using a gelatin coating with different thicknesses around the SNT. The release rate was adjusted by the amount of gelatin surrounding the SNT, with an increased barrier leading to a reduction in the release rate. A model developed on the basis of the Weibull modulus was established to fit the release results

  14. Carbon-14 releases from an unsaturated repository: A senseless but expensive dilemma

    International Nuclear Information System (INIS)

    Pflum, C.G.

    1993-01-01

    The purpose of the US Environmental Protection Agency (EPA) Environmental Standards for the Management and Disposal of Spent Nuclear Fuel, High-Level and Transuranic Radioactive Wastes (40 CFR Part 191 or standards) is to protect public health and safety. The 1985 rule was developed on the basis of the assumption that the repository would be located in a geologic formation that lies below the water table. It is appropriate to examine gaseous releases and transport of pollutants in order to determine site adequacy. When the provisions of the 1985 standard are applied to Yucca Mountain, specifically the limits for carbon-14, we can release in 10,000 years no more than 7,000 curies of carbon-14 in the form of carbon dioxide. Meanwhile, the US Department of Energy (DOE) and others indicate that the repository may release about 8,000 curies of carbon-14 dioxide, an amount that exceeds the standard by 10 to 20 percent. The original basis of the 1985 standards was that, in a site below the water table, the limit for carbon-14 was technically achievable. It was not a standard based on a release level that would prevent a danger to public health. If we examine the danger to public health of the release of 8,000 curies of carbon-14 dioxide during and 8,000-year period, this release would not a pose a significant threat to the average individual. Industry and natural sources release many times this amount of carbon-14 dioxide each year. The question therefore becomes: is it appropriate to spend an additional $3.2 billion on waste packages when the expenditure does not measurably improve the public health?

  15. Extended latanoprost release from commercial contact lenses: in vitro studies using corneal models.

    Directory of Open Access Journals (Sweden)

    Saman Mohammadi

    Full Text Available In this study, we compared, for the first time, the release of a 432 kDa prostaglandin F2a analogue drug, Latanoprost, from commercially available contact lenses using in vitro models with corneal epithelial cells. Conventional polyHEMA-based and silicone hydrogel soft contact lenses were soaked in drug solution (131 μg = ml solution in phosphate buffered saline. The drug release from the contact lens material and its diffusion through three in vitro models was studied. The three in vitro models consisted of a polyethylene terephthalate (PET membrane without corneal epithelial cells, a PET membrane with a monolayer of human corneal epithelial cells (HCEC, and a PET membrane with stratified HCEC. In the cell-based in vitro corneal epithelium models, a zero order release was obtained with the silicone hydrogel materials (linear for the duration of the experiment whereby, after 48 hours, between 4 to 6 μg of latanoprost (an amount well within the range of the prescribed daily dose for glaucoma patients was released. In the absence of cells, a significantly lower amount of drug, between 0.3 to 0.5 μg, was released, (p <0:001. The difference observed in release from the hydrogel lens materials in the presence and absence of cells emphasizes the importance of using an in vitro corneal model that is more representative of the physiological conditions in the eye to more adequately characterize ophthalmic drug delivery materials. Our results demonstrate how in vitro models with corneal epithelial cells may allow better prediction of in vivo release. It also highlights the potential of drug-soaked silicone hydrogel contact lens materials for drug delivery purposes.

  16. The effect of helium generation and irradiation temperature on tritium release from neutron irradiated beryllium

    International Nuclear Information System (INIS)

    Kupriyanov, I.B.; Gorokhov, V.A.; Vlasov, V.V.; Kovalev, A.M.; Chakin, V.P.

    2004-01-01

    The effect of neutron irradiation condition on tritium release from beryllium is described in this paper. Beryllium samples were irradiated in the SM reactor with neutron fluence (E > 0.1 MeV) of (0.37-2.0) x 10 22 cm -2 at 70-100degC and 650-700degC. Mass-spectrometer technique was used in out of tritium release experiments during stepped-temperature anneal within a temperature range from 250 to 1300degC. The total amount of helium accumulated in irradiated beryllium samples varied from 521 appm to 3061 appm. The first signs of tritium release were detected at temperature of 406-553degC. It was shown that irradiation temperature and helium generation level significantly affect the tritium release. A fraction of 44 - 74 % of tritium content in samples irradiated at low temperature (70 - 100degC) is release from beryllium at an annealing temperature below 800degC, whereas for samples after high temperature irradiation (650 - 700 degC) tritium release did not exceed 14 %. Majority of tritium (∼68%) is released within a temperature range from 800 to 920 degC. The increase of helium generation from 521 appm to 3061 appm results in lowering the temperature of maximal tritium release rate and the upper temperature of tritium release from beryllium by 100-130degC and 200-240degC, correspondingly. On the basis of data obtained, the diffusion coefficients of tritium in beryllium were calculated. (author)

  17. Development of CNC prototype for the characterization of the nanoparticle release during physical manipulation of nanocomposites.

    Science.gov (United States)

    Gendre, Laura; Marchante, Veronica; Abhyankar, Hrushikesh A; Blackburn, Kim; Temple, Clive; Brighton, James L

    2016-01-01

    This work focuses on the release of nanoparticles from commercially used nanocomposites during machining operations. A reliable and repeatable method was developed to assess the intentionally exposure to nanoparticles, in particular during drilling. This article presents the description and validation of results obtained from a new prototype used for the measurement and monitoring of nanoparticles in a controlled environment. This methodology was compared with the methodologies applied in other studies. Also, some preliminary experiments on drilling nanocomposites are included. Size, shape and chemical composition of the released nanoparticles were investigated in order to understand their hazard potential. No significant differences were found in the amount of nanoparticles released between samples with and without nanoadditives. Also, no chemical alteration was observed between the dust generated and the bulk material. Finally, further developments of the prototype are proposed.

  18. Interactions between Surfactants in Solution and Electrospun Protein Fibers: Effects on Release Behavior and Fiber Properties

    DEFF Research Database (Denmark)

    Boutrup Stephansen, Karen; García-Díaz, María; Jessen, Flemming

    2016-01-01

    , and drug delivery. In the present study, we present a systematic investigation of how surfactants and proteins, as physiologically relevant components, interact with insulin-loaded fish sarcoplasmic protein (FSP) electrospun fibers (FSP-Ins fibers) in solution and thereby affect fiber properties...... such as accessible surface hydrophilicity, physical stability, and release characteristics of an encapsulated drug. Interactions between insulin-loaded protein fibers and five anionic surfactants (sodium taurocholate, sodium taurodeoxycholate, sodium glycocholate, sodium glycodeoxycholate, and sodium dodecyl sulfate......), a cationic surfactant (benzalkonium chloride), and a neutral surfactant (Triton X-100) were studied. The anionic surfactants increased the insulin release in a concentration-dependent manner, whereas the neutral surfactant had no significant effect on the release. Interestingly, only minute amounts...

  19. Localisation and neural control of the release of calcitonin gene-related peptide (CGRP) from the isolated perfused porcine ileum

    DEFF Research Database (Denmark)

    Rasmussen, T N; Schmidt, P; Poulsen, S S

    2001-01-01

    was abolished by infusion of hexamethonium (3x10(-5) M). Infusion of capsaicin (10(-5) M) caused a significant increase in the release of CGRP-LI to 485+/-82% of basal output (n=5). Our results suggest a dual origin of CGRP innervation of the porcine ileum (intrinsic and extrinsic). The intrinsic CGRP neurons...... extracts, CGRP-LI corresponded entirely to porcine CGRP plus smaller amounts of oxidised CGRP. Using isolated vascularly perfused segments of the ileum, we studied the release of CGRP-LI in response to electrical stimulation of the mixed extrinsic periarterial nerves and to infusion of different...... receive excitatory input by parasympathetic, possibly vagal, preganglionic fibres, via release of acetylcholine acting on nicotinic receptors. The stimulatory effect of capsaicin suggests that CGRP is also released from extrinsic sensory neurons....

  20. The role of substrate morphology for the cytokine release profile of immature human primary macrophages

    Energy Technology Data Exchange (ETDEWEB)

    Bartneck, Matthias [Department of Medicine III, Medical Faculty, RWTH Aachen, Pauwelsstr. 30, 52074 Aachen (Germany); Heffels, Karl-Heinz [Department and Chair of Functional Materials in Medicine and Dentistry, University of Würzburg, Pleicherwall 2, 97070 Würzburg (Germany); Bovi, Manfred [Electron Microscopic Facility, Medical Faculty, RWTH Aachen (Germany); Groll, Jürgen [Department and Chair of Functional Materials in Medicine and Dentistry, University of Würzburg, Pleicherwall 2, 97070 Würzburg (Germany); Zwadlo-Klarwasser, Gabriele [Interdisciplinary Center for Clinical Research and Dept. of Dermatology, Medical Faculty, RWTH Aachen, Pauwelsstr. 30, 52056 Aachen (Germany)

    2013-12-01

    There is increasing evidence that the physicochemical nature of any given material is a dominant factor for the release of cytokines by innate immune cells, specifically of macrophages, and thus majorly influences their interaction with other cell types. Recently, we could show that the 3D structure of star shaped polytheylene oxide–polypropylene oxide co-polymers (sP(EO-stat-PO))-hydrogel coated substrates has a stronger influence on the release pattern of cytokines after 7 days of culture than surface chemistry. Here, we focused on the analysis of cytokine release over time and a more detailed analysis of cell morphology by scanning electron microscopy (SEM). Therefore, we compared different strategies for SEM sample preparation and found that using osmium tetroxide combined with aqua bidest led to best preparation results. For cytokine release we show significant changes from day 3 to day 7 of cell culture. After 3 days, the sP(EO-stat-PO)-coated substrates led to an induction of pro-angiogenic CCL3 and CCL4, and of low amounts of the anti-inflammatory IL10, which declined at day 7. In contrast, pleiotropic IL6 and the pro-inflammatory TNFα and IL1β were expressed stronger at day 7 than at day 3. - Highlights: • Strategies for the preparation of macrophages on hydrogel materials (Fig. 1) • Cytokine release of immature macrophages on the substrates (Fig. 2 and Table 1) • Changes in cytokine release during macrophage maturation (Table 2)

  1. Fission product release in conditions of a spent fuel pool severe accident

    International Nuclear Information System (INIS)

    Ohai, Dumitru

    2007-01-01

    Full text: Depending on the residence time, fuel burnup, and fuel rack configuration, there may be sufficient decay heat for the fuel clad to heat up, swell, and burst in case of a loss of pool water. Initiating event categories can be: loss of offsite power from events initiated by severe weather, internal fire, loss of pool cooling, loss of coolant inventory, seismic event, aircraft impact, tornado, missile attack. The breach in the clad releases the radioactive gases present in the gap between the fuel and clad, what is called 'gap release'. If the fuel continues to heat up, the zirconium clad will reach the point of rapid oxidation in air. This reaction of zirconium and air, or zirconium and steam is exothermic. The energy released from the reaction, combined with the fuel's decay energy, can cause the reaction to become self-sustaining and ignite the zirconium. The increase in heat from the oxidation reaction can also raise the temperature in adjacent fuel assemblies and propagate the oxidation reaction. Simultaneously, the sintered UO 2 pellets resulting from pins destroying are oxidized. Due to the self-disintegration of pellets by oxidation, fission gases and low volatile fission products are released. The release rate, the chemical nature and the amount of fission products depend on powder granulation distribution and environmental conditions. The zirconium burning and pellets self-disintegration will result in a significant release of spent fuel fission products that will be dispersed from the reactor site. (author)

  2. The role of substrate morphology for the cytokine release profile of immature human primary macrophages

    International Nuclear Information System (INIS)

    Bartneck, Matthias; Heffels, Karl-Heinz; Bovi, Manfred; Groll, Jürgen; Zwadlo-Klarwasser, Gabriele

    2013-01-01

    There is increasing evidence that the physicochemical nature of any given material is a dominant factor for the release of cytokines by innate immune cells, specifically of macrophages, and thus majorly influences their interaction with other cell types. Recently, we could show that the 3D structure of star shaped polytheylene oxide–polypropylene oxide co-polymers (sP(EO-stat-PO))-hydrogel coated substrates has a stronger influence on the release pattern of cytokines after 7 days of culture than surface chemistry. Here, we focused on the analysis of cytokine release over time and a more detailed analysis of cell morphology by scanning electron microscopy (SEM). Therefore, we compared different strategies for SEM sample preparation and found that using osmium tetroxide combined with aqua bidest led to best preparation results. For cytokine release we show significant changes from day 3 to day 7 of cell culture. After 3 days, the sP(EO-stat-PO)-coated substrates led to an induction of pro-angiogenic CCL3 and CCL4, and of low amounts of the anti-inflammatory IL10, which declined at day 7. In contrast, pleiotropic IL6 and the pro-inflammatory TNFα and IL1β were expressed stronger at day 7 than at day 3. - Highlights: • Strategies for the preparation of macrophages on hydrogel materials (Fig. 1) • Cytokine release of immature macrophages on the substrates (Fig. 2 and Table 1) • Changes in cytokine release during macrophage maturation (Table 2)

  3. An Investigation on Metallic Ion Release from Four Dental Casting Alloys

    Directory of Open Access Journals (Sweden)

    F. Nejatidanesh

    2005-12-01

    Full Text Available Statement of Problem: Element release from dental casting alloys into the oral environment is of clinical concern and is considered to be a potential health problem to all patients.Purpose: The aim of this study was to investigate the metallic ion release of four base metal alloys.Materials and Methods: Two Ni-Cr (Minalux and Supercast and two Co-Cr alloys (Minalia and Wironit were examined. Nine specimens of each type were prepared in 13×11×1.4 mm dimensions and each of the four alloys (3 specimens per group were conditioned in artificial saliva at 37 c for one, three and seven days.The conditioning media were analyzed for element-release using Inductive CoupledPlasma Atomic Emission Spectrophotometer (ICPAES. Collected data were statistically analyzed using ANOVA and Duncan multiple range test (P< 0.05.Results: The greatest amount of element release was seen after seven days (134.9 ppb Supercast, 159.2 ppb Minalux, 197.2 ppb Minalia, and 230.2 ppb Wironit. There was a significant difference between the released elements from the alloys after the three conditioning times (p<0.001.Conclusion: Element release from the studied alloys is proportional to the conditioning time. The Ni-Cr alloys tested in this investigation were more resistant to corrosion as compared to the Co-Cr alloys in artificial saliva. Supercast had the highest corrosion resistance.

  4. Can gamma irradiation during radiotherapy influence the metal release process for biomedical CoCrMo and 316L alloys?

    Science.gov (United States)

    Wei, Zheng; Edin, Jonathan; Karlsson, Anna Emelie; Petrovic, Katarina; Soroka, Inna L; Odnevall Wallinder, Inger; Hedberg, Yolanda

    2018-02-09

    The extent of metal release from implant materials that are irradiated during radiotherapy may be influenced by irradiation-formed radicals. The influence of gamma irradiation, with a total dose of relevance for radiotherapy (e.g., for cancer treatments) on the extent of metal release from biomedical stainless steel AISI 316L and a cobalt-chromium alloy (CoCrMo) was investigated in physiological relevant solutions (phosphate buffered saline with and without 10 g/L bovine serum albumin) at pH 7.3. Directly after irradiation, the released amounts of metals were significantly higher for irradiated CoCrMo as compared to nonirradiated CoCrMo, resulting in an increased surface passivation (enhanced passive conditions) that hindered further release. A similar effect was observed for 316L showing lower nickel release after 1 h of initially irradiated samples as compared to nonirradiated samples. However, the effect of irradiation (total dose of 16.5 Gy) on metal release and surface oxide composition and thickness was generally small. Most metals were released initially (within seconds) upon immersion from CoCrMo but not from 316L. Albumin induced an increased amount of released metals from AISI 316L but not from CoCrMo. Albumin was not found to aggregate to any greater extent either upon gamma irradiation or in the presence of trace metal ions, as determined using different light scattering techniques. Further studies should elucidate the effect of repeated friction and fractionated low irradiation doses on the short- and long term metal release process of biomedical materials. © 2018 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 2018. © 2018 The Authors Journal of Biomedical Materials Research Part B: Applied Biomaterials Published by Wiley Periodicals, Inc.

  5. "Effect of nano-filled surface coating agent on fluoride release from conventional glass ionomer cement: an in vitro trial".

    Science.gov (United States)

    Tiwari, S; Nandlal, B

    2013-01-01

    To overcome the drawbacks of glass ionomer cement of sensitivity to initial desiccation and moisture contamination the use of surface coating agent is recommended. The search in this area led to invent of use of nanofillers in surface coating agent, but its effect on fluoride release is not clear. The aim of this study is to evaluate and compare the fluoride release from conventional glass ionomer cement with and without surface coating agent. This in vitro study comprised of total 80 samples (40 samples of each with and without surface coating). Specimens were prepared, G coat plus was applied and light cured. Fluoride release of the sample was measured every 24 h for 7 days and weekly from 7th to 21 st day using Sension4 pH/ISE/MV Meter. Descriptive Statistics, Repeated Measure ANOVA, Paired Sample t-test, Independent Sample t-test, Scheffe post hoc test. Mean values clearly reveal a significant decrease in the fluoride release from day 1 to day 21 for both groups. Non-coated group released significantly more fluoride than surface coated group (Pagent will reduce the amount of fluoride released into oral environment as compared to non-coated group and at the same time releasing fluoride into surrounding cavity walls to create zones of inhibition into the cavity floor to help internal remineralization.

  6. Large scientific releases

    International Nuclear Information System (INIS)

    Pongratz, M.B.

    1981-01-01

    The motivation for active experiments in space is considered, taking into account the use of active techniques to obtain a better understanding of the natural space environment, the utilization of the advantages of space as a laboratory to study fundamental plasma physics, and the employment of active techniques to determine the magnitude, degree, and consequences of artificial modification of the space environment. It is pointed out that mass-injection experiments in space plasmas began about twenty years ago with the Project Firefly releases. Attention is given to mass-release techniques and diagnostics, operational aspects of mass release active experiments, the active observation of mass release experiments, active perturbation mass release experiments, simulating an artificial modification of the space environment, and active experiments to study fundamental plasma physics

  7. 24 CFR 891.525 - Amount and terms of financing.

    Science.gov (United States)

    2010-04-01

    ... 24 Housing and Urban Development 4 2010-04-01 2010-04-01 false Amount and terms of financing. 891... Handicapped-Section 8 Assistance § 891.525 Amount and terms of financing. (a) The amount of financing approved... financing provided shall not exceed the lesser of: (1) The dollar amounts stated in paragraphs (b) through...

  8. 45 CFR 149.100 - Amount of reimbursement.

    Science.gov (United States)

    2010-10-01

    ... 45 Public Welfare 1 2010-10-01 2010-10-01 false Amount of reimbursement. 149.100 Section 149.100... REQUIREMENTS FOR THE EARLY RETIREE REINSURANCE PROGRAM Reinsurance Amounts § 149.100 Amount of reimbursement... reimbursement in the amount of 80 percent of the costs for health benefits (net of negotiated price concessions...

  9. 40 CFR 721.90 - Release to water.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Release to water. 721.90 Section 721... SIGNIFICANT NEW USES OF CHEMICAL SUBSTANCES Certain Significant New Uses § 721.90 Release to water. Whenever a... predict the surface water concentration which will result from the intended release of the substance, if...

  10. Comparison of nickel and chromium ions released from stainless steel and NiTi wires after immersion in Oral B®, Orthokin® and artificial saliva.

    Science.gov (United States)

    Jamilian, Abdolreza; Moghaddas, Omid; Toopchi, Shabnam; Perillo, Letizia

    2014-07-01

    Oral environment of the mouth is a suitable place for biodegradation of alloys used in orthodontic wires. The toxicity of these alloys namely nickel and chromium has concerned the researchers about the release of these ions from orthodontic wires and brackets. The aim of this study was to measure the levels of nickel and chromium ions released from 0.018" stainless steel (SS) and NiTi wires after immersion in three solutions. One hundred and forty-four round NiTi and 144 round SS archwires with the diameters of 0.018" were immersed in Oral B®, Orthokin® and artificial saliva. The amounts of nickel and chromium ions released were measured after 1, 6, 24 hours and 7 days. Two way repeated ANOVA showed that the amount of chromium and nickel significantly increased in all solutions during all time intervals (p nickel ions were released more in NiTi wire in all solutions compared with SS wire. The lowest increase rate was also seen in artificial saliva. There is general consensus in literature that even very little amounts of nickel and chromium are dangerous for human body specially when absorbed orally; therefore, knowing the precise amount of these ions released from different wires when immersed in different mouthwashes is of high priority.

  11. Consequences of severe radioactive releases to Nordic Marine environment

    Energy Technology Data Exchange (ETDEWEB)

    Iosjpe, M. [Norwegian Radiation Protection Authority (NRPA) (Norway); Isaksson, M. [Univ. of Gothenburg (Sweden); Joensen, H.P. [Froskaparsetur Foeroya. Faroe Islands, Torshavn (Denmark); Lahtinen, J. [Radiation and Nuclear Safety Authority (Finland); Logemann, K. [Univ. of Iceland (Iceland); Palsson, S.E. [Geislavarnir Rikisins (Iceland); Roos, P. [Technical Univ. of Denmark. Risoe DTU, Roskilde (Denmark); Suolanen, V. [Technical Research Centre of Finland (Finland)

    2013-02-15

    chosen release fractions in the study were: iodine 20% (of the total core inventory), caesium 10%, tellurium 10%, strontium 0.5%, ruthenium 0.5%. The considered release event to marine environment were assumed to start ten hours after shutdown of the reactor. Total released amounts of the most important nuclides were estimated to be: 4.85{center_dot}10{sup 17} Bq (I-131), 7.29{center_dot}10{sup 16} Bq (Cs-134) and 4.17{center_dot}10{sup 16} Bq (Cs-137). Due to the highly contaminated sea food, the arising doses to human from a hypothetical severe nuclear power plant accident would be high especially in local sea area. Based on preliminary results, annual individual doses could be ten to some hundreds of millisieverts from local sea area. The most important nuclides were Cs-134, Cs-137 and I-131 causing 96% of the total ingestion dose. In the Baltic Sea area, the arising doses from a severe nuclear power plant accident assumed to happen e.g. at Gulf of Finland, would be about 1/10000 compared to doses in the local sea area. Thus the arising maximum annual individual dose for fish pathway is in the level of 0.1 mSv in the Baltic Sea area. Submarine accident assumed to happen at Icelandic waters, has been analysed in the study. The calculated collective dose rates to man as well as doses to a critical group are significantly lower than doses from natural sources. However, in local considerations dose-rates are significantly higher than the negligible component to the annual individual dose obtained from natural sources (UNSCEAR, 2000) and, therefore, have to be taken into consideration during evaluation of the accident consequences. (Author)

  12. Consequences of severe radioactive releases to Nordic Marine environment

    International Nuclear Information System (INIS)

    Iosjpe, M.; Isaksson, M.; Joensen, H.P.; Lahtinen, J.; Logemann, K.; Palsson, S.E.; Roos, P.; Suolanen, V.

    2013-02-01

    release fractions in the study were: iodine 20% (of the total core inventory), caesium 10%, tellurium 10%, strontium 0.5%, ruthenium 0.5%. The considered release event to marine environment were assumed to start ten hours after shutdown of the reactor. Total released amounts of the most important nuclides were estimated to be: 4.85·10 17 Bq (I-131), 7.29·10 16 Bq (Cs-134) and 4.17·10 16 Bq (Cs-137). Due to the highly contaminated sea food, the arising doses to human from a hypothetical severe nuclear power plant accident would be high especially in local sea area. Based on preliminary results, annual individual doses could be ten to some hundreds of millisieverts from local sea area. The most important nuclides were Cs-134, Cs-137 and I-131 causing 96% of the total ingestion dose. In the Baltic Sea area, the arising doses from a severe nuclear power plant accident assumed to happen e.g. at Gulf of Finland, would be about 1/10000 compared to doses in the local sea area. Thus the arising maximum annual individual dose for fish pathway is in the level of 0.1 mSv in the Baltic Sea area. Submarine accident assumed to happen at Icelandic waters, has been analysed in the study. The calculated collective dose rates to man as well as doses to a critical group are significantly lower than doses from natural sources. However, in local considerations dose-rates are significantly higher than the negligible component to the annual individual dose obtained from natural sources (UNSCEAR, 2000) and, therefore, have to be taken into consideration during evaluation of the accident consequences. (Author)

  13. Presynaptic M1 muscarinic receptor modulates spontaneous release of acetylcholine from rat basal forearm slices

    International Nuclear Information System (INIS)

    Suzuki, T.; Fujimoto, LK.; Oohata, H.; Kawashima, K.

    1988-01-01

    Spontaneous release of (ACh) from rat basal forebrain slices in the presence of cholinesterase inhibitor was directly determined using a specific radioimmunoassay for ACh. The release was calcium dependent. A consistent amount of ACh release was observed throughout the experiment. Atropine (10- 8 to 10- 5 M) and pirenzepine (10- 7 to 10- 5 M) enhanced spontaneous ACh release. These findings indicate the presence of an M 1 muscarenic autoreceptor that modulates spontaneous release of ACh in the rat forebrain

  14. Solubility and fluoride release in ionomers and compomers.

    Science.gov (United States)

    Bertacchini, S M; Abate, P F; Blank, A; Baglieto, M F; Macchi, R L

    1999-03-01

    The degree of solubility and the fluoride release of glass-ionomer cements and "compomers" were determined as a function of time. Three conventional glass-ionomer cements, three hybrid ionomers, and two compomers were included in the study. Disk-shaped specimens were prepared and immersed in a lactic acid solution. Solubility was evaluated from determinations of loss of mass as a function of time. To evaluate fluoride release, similar specimens were immersed in 50 mL of deionized water to which 50 mL of buffer solution was added. A fluoride ion detector was used to read the concentration of fluoride ion in the overall solution at different times after immersion. Material and time factors had a significant influence on results. The compomers showed less corrosion and fluoride release than the ionomers. Some correlation was found between solubility and fluoride leakage values. Components of both the ionomers and compomers that were studied can dissolve in water. The materials leak fluoride ions in amounts that differ according to the characteristics of the individual products.

  15. Diagnostic value of determination of amount of urinary excretion of proteins for early diabetic nephropathy

    International Nuclear Information System (INIS)

    Li Zhuocheng; Chen Jianxiong; Yan Dewen

    2007-01-01

    Objective: To investigate the value of detection of changes of the amount of usinary excretion of albumin, β 2 -m, Tamm- Horsfall protein and α 1 -m for diagnosis of early diabetic nephropathy. Methods: The amounts of 24h urinary excretion of albumin, β 2 -m, Tamm-Horsfall protein and α 1 -m were determined with RIA in 78 patients with diabetes mellitus and 40 controls. Results: The amounts of 24h urinary excretion of albumin, β 2 -m, α 1 -m in patients with diabetes mellitus were significantly higher than those in controls (P<0.01 ), while the amount of Tamm-Horsfall protein was significantly lower (P<0.01). Among the diabetic patients, the changes of the amount of protein excretion were more pronounced in those with advanced impairment of renal function. Conclusion: Determination of amount of urinary excretion of proteins was helpful for diagnosis and assessment of early diabetic nephropathy. (authors)

  16. Detecting Novelty and Significance

    Science.gov (United States)

    Ferrari, Vera; Bradley, Margaret M.; Codispoti, Maurizio; Lang, Peter J.

    2013-01-01

    Studies of cognition often use an “oddball” paradigm to study effects of stimulus novelty and significance on information processing. However, an oddball tends to be perceptually more novel than the standard, repeated stimulus as well as more relevant to the ongoing task, making it difficult to disentangle effects due to perceptual novelty and stimulus significance. In the current study, effects of perceptual novelty and significance on ERPs were assessed in a passive viewing context by presenting repeated and novel pictures (natural scenes) that either signaled significant information regarding the current context or not. A fronto-central N2 component was primarily affected by perceptual novelty, whereas a centro-parietal P3 component was modulated by both stimulus significance and novelty. The data support an interpretation that the N2 reflects perceptual fluency and is attenuated when a current stimulus matches an active memory representation and that the amplitude of the P3 reflects stimulus meaning and significance. PMID:19400680

  17. Significant NRC Enforcement Actions

    Data.gov (United States)

    Nuclear Regulatory Commission — This dataset provides a list of Nuclear Regulartory Commission (NRC) issued significant enforcement actions. These actions, referred to as "escalated", are issued by...

  18. Impact of physicochemical properties of porous silica materials conjugated with dexamethasone via pH-responsive hydrazone bond on drug loading and release behavior

    Science.gov (United States)

    Numpilai, Thanapha; Witoon, Thongthai; Chareonpanich, Metta; Limtrakul, Jumras

    2017-02-01

    The conjugation of dexamethasone (DEX) onto modified-porous silica materials via a pH-responsive hydrazone bond has been reported to be highly efficient method to specifically deliver the DEX to diseased sites. However, the influence of physicochemical properties of porous silica materials has not yet been fully understood. In this paper, the impact of pore sizes, particle sizes and silanol contents on surface functionalization, drug loading and release behavior of porous silica materials conjugated with dexamethasone via pH-responsive hydrazone bond was investigated. The grafting density was found to relate to the number of silanol groups on the surface of porous silica materials. The particle size and macropores of the porous silica materials played an vital role on the drug loading and release behavior. Although the porous silica materials with larger particle sizes possessed a lower grafting density, a larger amount of drug loading could be achieved. Moreover, the porous silica materials with larger particle sizes showed a slower release rate of DEX due to a longer distance for cleaved DEX diffusion out of pores. DEX release rate exhibited pH-dependent, sustained release. At pH 4.5, the amount of DEX release within 10 days could be controlled in the range of 12.74-36.41%, depending on the host material. Meanwhile, less than 1.5% of DEX was released from each of type of the porous silica materials at pH 7.4. The results of silica dissolution suggested that the degradation of silica matrix did not significantly affect the release rate of DEX. In addition, the kinetic modeling studies revealed that the DEX releases followed Korsmeyer-Peppas model with a release exponent (n) ranged from 0.3 to 0.47, indicating a diffusion-controlled release mechanism.

  19. The Significance of Science

    Science.gov (United States)

    Pielke, R.

    2002-05-01

    Whether global warming, terrestrial carbon sinks, ecosystem functioning, genetically modified organisms, cloning, vaccination or chemicals in the environment, science is increasingly the battlefield on which political advocates, not least lawyers and commercial interests, manipulate `facts' to their preferred direction, which fosters the politicization of science. Debate putatively over science increasingly relies on tactics such as ad hominem attacks and criticism of process (for example, peer review or sources of funding), through paid advertisements, press releases and other publicity campaigns. As political battles are waged through `science', many scientists are willing to adopt tactics of demagoguery and character assassination as well as, or even instead of, reasoned argument, as in aspects of debate over genetically modified crops or global warming. Science is becoming yet another playing field for power politics, complete with the trappings of media spin and a win-at-all-costs attitude. Sadly, much of what science can offer policymakers, and hence society, is lost. This talk will use cases from the atmospheric sciences as points of departure to explore the politicization of science from several perspectives and address questions such as: Is it a problem? For whom and what outcomes? What are the alternatives to business-as-usual?

  20. Design of sustained-release nitrendipine microspheres having solid dispersion structure by quasi-emulsion solvent diffusion method

    DEFF Research Database (Denmark)

    Cui, Fude; Yang, Mingshi; Jiang, Yanyan

    2003-01-01

    crystallization technique, i.e. quasi-emulsion solvent diffusion method. The factors of effect on micromeritic properties and release profiles of the resultant microspheres were investigated. And the bioavailability of nitrendipine microspheres was evaluated in six healthy dogs. The results showed...... that the particle size of microspheres was determined mainly by the agitation speed. The dissolution rate of nitrendipine from microspheres was enhanced significantly with increasing the amount of dispersing agents, and sustained by adding retarding agents. The release rate of microspheres could be controlled...

  1. Microemulsion-Based Mucoadhesive Buccal Wafers: Wafer Formation, In Vitro Release, and Ex Vivo Evaluation.

    Science.gov (United States)

    Pham, Minh Nguyet; Van Vo, Toi; Tran, Van-Thanh; Tran, Phuong Ha-Lien; Tran, Thao Truong-Dinh

    2017-10-01

    Microemulsion has the potentials to enhance dissolution as well as facilitate absorption and permeation of poorly water-soluble drugs through biological membranes. However, its application to govern a controlled release buccal delivery for local treatment has not been discovered. The aim of this study is to develop microemulsion-based mucoadhesive wafers for buccal delivery based on an incorporation of the microemulsion with mucoadhesive agents and mannitol. Ratio of oil to surfactant to water in the microemulsion significantly impacted quality of the wafers. Furthermore, the combination of carbopol and mannitol played a key role in forming the desired buccal wafers. The addition of an extra 50% of water to the formulation was suitable for wafer formation by freeze-drying, which affected the appearance and distribution of carbopol in the wafers. The amount of carbopol was critical for the enhancement of mucoadhesive properties and the sustained drug release patterns. Release study presented a significant improvement of the drug release profile following sustained release for 6 h. Ex vivo mucoadhesive studies provided decisive evidence to the increased retention time of wafers along with the increased carbopol content. The success of this study indicates an encouraging strategy to formulate a controlled drug delivery system by incorporating microemulsions into mucoadhesive wafers.

  2. Bioactive Glass Nanoparticles as a New Delivery System for Sustained 5-Fluorouracil Release: Characterization and Evaluation of Drug Release Mechanism

    Directory of Open Access Journals (Sweden)

    Abeer M. El-Kady

    2015-01-01

    Full Text Available Bioactive glass nanoparticles were synthesized and tested for the first time as a new delivery system for sustained 5-fluorouracil (5-FU release. They were characterized by TEM, DTA, TGA, and FT-IR. The porosity % and specific surface area of glass nanoparticles were 85.59% and 378.36 m2/g, respectively. The in vitro bioactivity evaluation confirmed that bioactive glass disks prepared from these nanoparticles could induce hydroxyapatite layer over their surfaces in simulated body fluid. The in vitro drug release experiment indicated that glass nanoparticles could serve as long-term local delivery vehicles for sustained 5-FU release. The release profile of 5-FU showed an initial fast release stage followed by a second stage of slower release. The initial burst release of 5-FU in the first day was about 23% (28.92 mg·L−1 of the total amount of loaded 5-FU, while the final cumulative percentage of the 5-FU released after 32 days was about 45.6% (57.31 mg·L−1 of the total amount of loaded 5-FU. The application of different mathematical models indicated that 5-FU was released by diffusion controlled mechanism and suggested that its release rate was dependent on glass particles dissolution, changes of surface area as well as diameter of glass particles, and concentration of loaded drug.

  3. Effects of exogenous salinity (NaCl) gradient on Cd release in acidified contaminated brown soil

    Science.gov (United States)

    Zhang, Lina; Rong, Yong; Mao, Li; Gao, Zhiyuan; Liu, Xiaoyu; Dong, Zhicheng

    2018-02-01

    Taking acidified Cd contaminated brown soil in Yantai as the research object, based on different exogenous salinity (NaCl) gradient (0%, 0.3%, 0.6%, 0.9%, 1.5%, 2% and 5%), indoor simulation experiments of Cd release were carried out after field investigation. Results showed that there was a significantly positive relation (r>0.90) between Cd release concentration/amount/ratio and exogenous salt (NaCl). Besides, the more exogenous salt (NaCl) was added; maximum release concentration/amount of Cd appeared the earlier. It was found that exogenous salt (NaCl) addition could obviously promote Cd release from acidified Cd contaminated brown soil. It was believed that this could be mainly due to the cation exchange between Cd2+ and Na+, together with the dissociation and/or complexation between Cl- and Cd2+. In addition, available adsorption sites reduction by exchange base in soil causing Cd changed from solid state to soil solution was also a probable reason.

  4. EIA new releases

    International Nuclear Information System (INIS)

    1994-09-01

    This report is a compliation of news releases from the Energy Information Administration. The september-october report includes articles on energy conservation, energy consumption in commercial buildings, and a short term energy model for a personal computer

  5. Air exposure and sample storage time influence on hydrogen release from tungsten

    Energy Technology Data Exchange (ETDEWEB)

    Moshkunov, K.A., E-mail: moshkunov@gmail.co [National Research Nuclear University ' MEPhI' , Kashirskoe sh. 31, 115409 Moscow (Russian Federation); Schmid, K.; Mayer, M. [Max-Planck-Institut fuer Plasmaphysik, EURATOM Association, Boltzmannstrasse 2, D-85748 Garching (Germany); Kurnaev, V.A.; Gasparyan, Yu.M. [National Research Nuclear University ' MEPhI' , Kashirskoe sh. 31, 115409 Moscow (Russian Federation)

    2010-09-30

    In investigations of hydrogen retention in first wall components the influence of the conditions of the implanted target storage prior to analysis and the storage time is often neglected. Therefore we have performed a dedicated set of experiments. The release of hydrogen from samples exposed to ambient air after irradiation was compared to samples kept in vacuum. For air exposed samples significant amounts of HDO and D{sub 2}O are detected during TDS. Additional experiments have shown that heavy water is formed by recombination of releasing D and H atoms with O on the W surface. This water formation can alter hydrogen retention results significantly, in particular - for low retention cases. In addition to the influence of ambient air exposure also the influence of storage time in vacuum was investigated. After implantation at 300 K the samples were stored in vacuum for up to 1 week during which the retained amount decreased significantly. The subsequently measured TDS spectra showed that D was lost from both the high and low energy peaks during storage at ambient temperature of {approx}300 K. An attempt to simulate this release from both peaks during room temperature storage by TMAP 7 calculations showed that this effect cannot be explained by conventional diffusion/trapping models.

  6. Air exposure and sample storage time influence on hydrogen release from tungsten

    International Nuclear Information System (INIS)

    Moshkunov, K.A.; Schmid, K.; Mayer, M.; Kurnaev, V.A.; Gasparyan, Yu.M.

    2010-01-01

    In investigations of hydrogen retention in first wall components the influence of the conditions of the implanted target storage prior to analysis and the storage time is often neglected. Therefore we have performed a dedicated set of experiments. The release of hydrogen from samples exposed to ambient air after irradiation was compared to samples kept in vacuum. For air exposed samples significant amounts of HDO and D 2 O are detected during TDS. Additional experiments have shown that heavy water is formed by recombination of releasing D and H atoms with O on the W surface. This water formation can alter hydrogen retention results significantly, in particular - for low retention cases. In addition to the influence of ambient air exposure also the influence of storage time in vacuum was investigated. After implantation at 300 K the samples were stored in vacuum for up to 1 week during which the retained amount decreased significantly. The subsequently measured TDS spectra showed that D was lost from both the high and low energy peaks during storage at ambient temperature of ∼300 K. An attempt to simulate this release from both peaks during room temperature storage by TMAP 7 calculations showed that this effect cannot be explained by conventional diffusion/trapping models.

  7. Air exposure and sample storage time influence on hydrogen release from tungsten

    Science.gov (United States)

    Moshkunov, K. A.; Schmid, K.; Mayer, M.; Kurnaev, V. A.; Gasparyan, Yu. M.

    2010-09-01

    In investigations of hydrogen retention in first wall components the influence of the conditions of the implanted target storage prior to analysis and the storage time is often neglected. Therefore we have performed a dedicated set of experiments. The release of hydrogen from samples exposed to ambient air after irradiation was compared to samples kept in vacuum. For air exposed samples significant amounts of HDO and D 2O are detected during TDS. Additional experiments have shown that heavy water is formed by recombination of releasing D and H atoms with O on the W surface. This water formation can alter hydrogen retention results significantly, in particular - for low retention cases. In addition to the influence of ambient air exposure also the influence of storage time in vacuum was investigated. After implantation at 300 K the samples were stored in vacuum for up to 1 week during which the retained amount decreased significantly. The subsequently measured TDS spectra showed that D was lost from both the high and low energy peaks during storage at ambient temperature of ˜300 K. An attempt to simulate this release from both peaks during room temperature storage by TMAP 7 calculations showed that this effect cannot be explained by conventional diffusion/trapping models.

  8. What does it take to build a medium scale scientific cloud to process significant amounts of Earth observation data?

    Science.gov (United States)

    Hollstein, André; Diedrich, Hannes; Spengler, Daniel

    2017-04-01

    The installment of the operational fleet of Sentinels by Copernicus offers an unprecedented influx of freely available Earth Observation data with Sentinel-2 being a great example. It offers a broad range of land applications due to its high spatial sampling from 10 m to 20 m and its multi-spectral imaging capabilities with 13 spectral bands. The open access policy allows unrestricted use by everybody and provides data downloads for on the respective sites. For a small area of interest and shorter time series, data processing, and exploitation can easily be done manually. However, for multi-temporal analysis of larger areas, the data size can quickly increase such that it is not manageable in practice on a personal computer which leads to an increasing interest in central data exploitation platforms. Prominent examples are GoogleEarth Engine, NASA Earth Exchange (NEX) or current developments such as CODE-DE in Germany. Open standards are still evolving, and the choice of a platform may create lock-in scenarios and a situation where scientists are not anymore in full control of all aspects of their analysis. Securing intellectual properties of researchers can become a major issue in the future. Partnering with a startup company that is dedicated to providing tools for farm management and precision farming, GFZ builds a small-scale science cloud named GTS2 for processing and distribution of Sentinel-2 data. The service includes a sophisticated atmospheric correction algorithm, spatial co-registration of time series data, as well as a web API for data distribution. This approach is different from the drag to centralized research using infrastructures controlled by others. By keeping the full licensing rights, it allows developing new business models independent from the initially chosen processing provider. Currently, data is held for the greater German area but is extendable to larger areas on short notice due to a scalable distributed network file system. For a given area of interest, band and time range selection, the API returns only the data that was requested in a fast manner and thereby saves storage space on the user's machine. A jupyterhub instance is a main tool for data exploitation by our users. Nearly all used software is open source, is based on open standards, and allows to transfer software to other infrastructures. In the talk, we give an overview of the current status of the project and the service, but also want to share our experience with its development.

  9. Sellafield (release of radioactivity)

    Energy Technology Data Exchange (ETDEWEB)

    Cunningham, J; Goodlad, A; Morris, M

    1986-02-06

    A government statement is reported, about the release of plutonium nitrate at the Sellafield site of British Nuclear Fuels plc on 5 February 1986. Matters raised included: details of accident; personnel monitoring; whether radioactive material was released from the site; need for public acceptance of BNFL activities; whether plant should be closed; need to reduce level of radioactive effluent; number of incidents at the plant.

  10. Tunable release of clavam from clavam stabilized gold nanoparticles — Design, characterization and antimicrobial study

    Energy Technology Data Exchange (ETDEWEB)

    Manju, V. [Electrodics and Electrocatalysis Division, CSIR-Central Electrochemical Research Institute, Karaikudi, Tamilnadu 630006 (India); Dhandapani, P. [Corrosion Materials and Protection Division, CSIR-Central Electrochemical Research Institute, Karaikudi, Tamilnadu, 630006 (India); Gurusamy Neelavannan, M. [Characterization and Measurement lab, CSIR-Central Electrochemical Research Institute, Karaikudi, Tamilnadu 630006 (India); Maruthamuthu, S. [Corrosion Materials and Protection Division, CSIR-Central Electrochemical Research Institute, Karaikudi, Tamilnadu, 630006 (India); Berchmans, S. [Electrodics and Electrocatalysis Division, CSIR-Central Electrochemical Research Institute, Karaikudi, Tamilnadu 630006 (India); Palaniappan, A., E-mail: palani112@gmail.com [Electrodics and Electrocatalysis Division, CSIR-Central Electrochemical Research Institute, Karaikudi, Tamilnadu 630006 (India)

    2015-04-01

    A facile one-step approach is developed to synthesize highly stable (up to 6 months) gold nanoparticles (GNPs) using Clavam, pharmaceutical form of amoxicillin which contains a mixture of amoxicillin and potassium salt of clavulanic acid, at room temperature (25–30 °C). The clavam stabilized GNPs are characterized using various techniques including UV–Visible, FT-IR spectrophotometry and transmission electron microscopy (TEM). Tunable release of clavam from clavam stabilized GNPs is demonstrated using intracellular concentrations of glutathione (GSH). The process is monitored using an UV–Vis spectroscopy and the amount of clavam released in terms of amoxicillin concentration is quantitatively estimated using reverse phase high performance liquid chromatographic (RP-HPLC) technique. In vitro study reveals that the clavam released from GNPs' surface was found to show a significant enhancement in antibacterial activity against Escherichia coli and the cause of enhancement is addressed. - Graphical abstract: Stable and nearly monodisperse gold nanoparticles (GNPs) are prepared at room temperature (~ 25–30 °C) using clavam; commercial form of amoxicillin antibiotic. Tunable release of clavam from clavam stabilized GNPs is demonstrated by the addition of varying concentrations of glutathione. Interactions between clavam and gold core are investigated in detail. The mechanism of enhanced antimicrobial activity of clavam released from clavam stabilized GNPs is probed. - Highlights: • Gold nanoparticles (GNPs) are prepared without reducing agent using antibiotic clavam{sup TR}. • Our work shed lights on the nature of interaction between the clavam and GNPs. • Sustained release of clavam from clavam stabilized GNPs is demonstrated using glutathione. • Antimicrobial activity of the released clavam is confirmed using various techniques. • Our study suggests that the clavam released from GNPs shows better inhibition of E. coli.

  11. Recombinant human bone morphogenetic protein-2 released from polyurethane-based scaffolds promotes early osteogenic differentiation of human mesenchymal stem cells

    International Nuclear Information System (INIS)

    Kim, Jinku; Hollinger, Jeffrey O

    2012-01-01

    The purposes of this study were to determine the pharmacokinetics of recombinant human bone morphogenetic protein-2 (rhBMP-2) from a polyurethane (PUR)-based porous scaffold and to determine the biological responses of human mesenchymal stem cells (hMSCs) to the rhBMP-2 released from those scaffolds. The rhBMP-2 was incorporated into the PUR three-dimensional (3D) porous scaffolds and release profiles were determined using enzyme-linked immunosorbent assay. The bioactivity of the rhBMP-2 containing releasates was determined using hMSCs and compared with exogenous rhBMP-2. Release of rhBMP-2 from PUR-based systems was bi-phasic and characterized by an initial burst followed by a sustained release for up to 21 days. Expression of alkaline phosphatase activity by hMSCs treated with the rhBMP-2 releasates was significantly greater than the cells alone (control) throughout the time periods. Furthermore, after 14 days of culture, the hMSCs cultured with rhBMP-2 releasate had a greater amount of mineralization compared to exogenous rhBMP-2. Overall, the rhBMP-2 release from the PUR-based scaffolds was sustained for 21 days and the releasates appeared to be bioactive and promoted earlier osteogenic differentiation and mineralization of hMSCs than the exogenous rhBMP-2. (paper)

  12. [Preparation of hydrophilic matrix sustained release tablets of total lactones from Andrographis paniculata and study on its in vitro release mechanism].

    Science.gov (United States)

    Xu, Fang-Fang; Shi, Wei; Zhang, Hui; Guo, Qing-Ming; Wang Zhen-Zhong; Bi, Yu-An; Wang, Zhi-Min; Xiao, Wei

    2015-01-01

    In this study, hydrophilic matrix sustained release tablets of total lactones from Andrographis paniculata were prepared and the in vitro release behavior were also evaluated. The optimal prescription was achieved by studying the main factor of the type and amount of hydroxypropyl methylcellulose (HPMC) using single factor test and evaluating through cumulative release of three lactones. No burst drug release from the obtained matrix tablets was observed. Drug release sustained to 14 h. The release mechanism of three lactones from A. paniculata was accessed by zero-order, first-order, Higuchi and Peppas equation. The release behavior of total lactones from A. paniculata was better agreed with Higuchi model and the drug release from the tablets was controlled by degradation of the matrix. The preparation of hydrophilic matrix sustained release tablets of total lactones from A. paniculata with good performance of drug release was simple.

  13. Fuel morphology effects on fission product release

    International Nuclear Information System (INIS)

    Osetek, D.J.; Hartwell, J.K.; Cronenberg, A.W.

    1986-01-01

    Results are presented of fission product release behavior observed during four severe fuel damage tests on bundles of UO 2 fuel rods. Transient temperatures up to fuel melting were obtained in the tests that included both rapid and slow cooldown, low and high (36 GWd/t) burnup fuel and the addition of Ag-In-Cd control rods. Release fractions of major fission product species and release rates of noble gas species are reported. Significant differences in release behavior are discussed between heatup and cooldown periods, low and high burnup fuel and long- and short-lived fission products. Explanations for the observed differences are offered that relate fuel morphology changes to the releases

  14. Intracellular sphingosine releases calcium from lysosomes.

    Science.gov (United States)

    Höglinger, Doris; Haberkant, Per; Aguilera-Romero, Auxiliadora; Riezman, Howard; Porter, Forbes D; Platt, Frances M; Galione, Antony; Schultz, Carsten

    2015-11-27

    To elucidate new functions of sphingosine (Sph), we demonstrate that the spontaneous elevation of intracellular Sph levels via caged Sph leads to a significant and transient calcium release from acidic stores that is independent of sphingosine 1-phosphate, extracellular and ER calcium levels. This photo-induced Sph-driven calcium release requires the two-pore channel 1 (TPC1) residing on endosomes and lysosomes. Further, uncaging of Sph leads to the translocation of the autophagy-relevant transcription factor EB (TFEB) to the nucleus specifically after lysosomal calcium release. We confirm that Sph accumulates in late endosomes and lysosomes of cells derived from Niemann-Pick disease type C (NPC) patients and demonstrate a greatly reduced calcium release upon Sph uncaging. We conclude that sphingosine is a positive regulator of calcium release from acidic stores and that understanding the interplay between Sph homeostasis, calcium signaling and autophagy will be crucial in developing new therapies for lipid storage disorders such as NPC.

  15. Inhibition of insulin release by cyproheptadine: Effects on 3',5'-cyclic-AMP-content and /sup 45/Ca-accumulation of incubated mouse islets

    Energy Technology Data Exchange (ETDEWEB)

    Joost, H G; Beckmann, J; Lenzen, S; Hasselblatt, A [Goettingen Univ. (F.R. Germany)

    1976-01-01

    Cyproheptadine (1, 10 and 100 ..mu..m) significantly reduced insulin release from isolated mouse islets in response to glucose. In contrast, 1 mM cyproheptadine induced a large release of insulin into the incubation medium probably due to islet cell damage, since the islets had lost a considerable amount of their protein content. 3',5'-cyclic-AMP-levels of the islets were not significantly affected by 10 ..mu..M cyproheptadine in the presence as well as in the absence of theophylline (10 mM). As the inhibitory effect of cyproheptadine on insulin release was correlated with reduced accumulation of calcium-45, the agent may inhibit insulin release by interfering with the calcium handling of the ..beta..-cell.

  16. Determinants of quality, latency, and amount of Stack Overflow answers about recent Android APIs

    Science.gov (United States)

    Filkov, Vladimir

    2018-01-01

    Stack Overflow is a popular crowdsourced question and answer website for programming-related issues. It is an invaluable resource for software developers; on average, questions posted there get answered in minutes to an hour. Questions about well established topics, e.g., the coercion operator in C++, or the difference between canonical and class names in Java, get asked often in one form or another, and answered very quickly. On the other hand, questions on previously unseen or niche topics take a while to get a good answer. This is particularly the case with questions about current updates to or the introduction of new application programming interfaces (APIs). In a hyper-competitive online market, getting good answers to current programming questions sooner could increase the chances of an app getting released and used. So, can developers anyhow, e.g., hasten the speed to good answers to questions about new APIs? Here, we empirically study Stack Overflow questions pertaining to new Android APIs and their associated answers. We contrast the interest in these questions, their answer quality, and timeliness of their answers to questions about old APIs. We find that Stack Overflow answerers in general prioritize with respect to currentness: questions about new APIs do get more answers, but good quality answers take longer. We also find that incentives in terms of question bounties, if used appropriately, can significantly shorten the time and increase answer quality. Interestingly, no operationalization of bounty amount shows significance in our models. In practice, our findings confirm the value of bounties in enhancing expert participation. In addition, they show that the Stack Overflow style of crowdsourcing, for all its glory in providing answers about established programming knowledge, is less effective with new API questions. PMID:29547620

  17. Determinants of quality, latency, and amount of Stack Overflow answers about recent Android APIs.

    Science.gov (United States)

    Kavaler, David; Filkov, Vladimir

    2018-01-01

    Stack Overflow is a popular crowdsourced question and answer website for programming-related issues. It is an invaluable resource for software developers; on average, questions posted there get answered in minutes to an hour. Questions about well established topics, e.g., the coercion operator in C++, or the difference between canonical and class names in Java, get asked often in one form or another, and answered very quickly. On the other hand, questions on previously unseen or niche topics take a while to get a good answer. This is particularly the case with questions about current updates to or the introduction of new application programming interfaces (APIs). In a hyper-competitive online market, getting good answers to current programming questions sooner could increase the chances of an app getting released and used. So, can developers anyhow, e.g., hasten the speed to good answers to questions about new APIs? Here, we empirically study Stack Overflow questions pertaining to new Android APIs and their associated answers. We contrast the interest in these questions, their answer quality, and timeliness of their answers to questions about old APIs. We find that Stack Overflow answerers in general prioritize with respect to currentness: questions about new APIs do get more answers, but good quality answers take longer. We also find that incentives in terms of question bounties, if used appropriately, can significantly shorten the time and increase answer quality. Interestingly, no operationalization of bounty amount shows significance in our models. In practice, our findings confirm the value of bounties in enhancing expert participation. In addition, they show that the Stack Overflow style of crowdsourcing, for all its glory in providing answers about established programming knowledge, is less effective with new API questions.

  18. Release of Growth Factors into Root Canal by Irrigations in Regenerative Endodontics.

    Science.gov (United States)

    Zeng, Qian; Nguyen, Sean; Zhang, Hongming; Chebrolu, Hari Priya; Alzebdeh, Dalia; Badi, Mustafa A; Kim, Jong Ryul; Ling, Junqi; Yang, Maobin

    2016-12-01

    The aim of this study was to investigate the release of growth factors into root canal space after the irrigation procedure of regenerative endodontic procedure. Sixty standardized root segments were prepared from extracted single-root teeth. Nail varnish was applied to all surfaces except the root canal surface. Root segments were irrigated with 1.5% NaOCl + 17% EDTA, 2.5% NaOCl + 17% EDTA, 17% EDTA, or deionized water. The profile of growth factors that were released after irrigation was studied by growth factor array. Enzyme-linked immunosorbent assay was used to validate the release of transforming growth factor (TGF)-β1 and basic fibroblast growth factor (bFGF) at 4 hours, 1 day, and 3 days after irrigation. The final concentrations were calculated on the basis of the root canal volume measured by cone-beam computed tomography. Dental pulp stem cell migration on growth factors released from root segments was measured by using Transwell assay. Total of 11 of 41 growth factors were detected by growth factors array. Enzyme-linked immunosorbent assay showed that TGF-β1 was released in all irrigation groups. Compared with the group with 17% EDTA (6.92 ± 4.49 ng/mL), the groups with 1.5% NaOCl + 17% EDTA and 2.5% NaOCl + 17% EDTA had significantly higher release of TGF-β1 (69.04 ± 30.41 ng/mL and 59.26 ± 3.37 ng/mL, respectively), with a peak release at day 1. The release of bFGF was detected at a low level in all groups (0 ng/mL to 0.43 ± 0.22 ng/mL). Migration assay showed the growth factors released from root segments induced dental pulp stem cell migration. The root segment model in present study simulated clinical scenario and indicated that the current irrigation protocol released a significant amount of TGF-β1 but not bFGF. The growth factors released into root canal space induced dental pulp stem cell migration. Copyright © 2016 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

  19. Formal conditions for the significance-effect

    DEFF Research Database (Denmark)

    Thellefsen, Torkild Leo; Sørensen, Bent; Thellefsen, Martin

    2006-01-01

    The significance-effect is the right effect of meaning caused upon an interpreting mind. The right effect is understood as the right interpretation of an intended meaning caused by a sign communicated by an utterer. In the article, which is inspired by Charles S. Peirce's doctrine of signs, his s...... semeiotics and his theory of communication, we account for the formal conditions that have to be present for the release of the significance-effect....

  20. Effect of bioceramic functional groups on drug binding and release kinetics

    Science.gov (United States)

    Trujillo, Christopher

    DI water for 2 days and the concentrations of dissolved silicate and phosphate ions released from the surface of Cris were measured using Inductively Coupled Plasma -- Optical Emission Spectrometry (ICP-OES). The phosphate ions released from the material activated the surface and exposed the silicate functional groups as indicated by the FTIR analysis. Pre-immersed Cris particles and control non-immersed samples (200 mg, n=5 for each sample) of particle size 90-150 mum were immersed in 2 mL of vancomycin (Vanc) solution (8 mg/ml) in PBS on an orbital shaker at 37°C for 24 hours. The amount of drug bound to the material was measured by High Performance Liquid Chromatography (HPLC). Control non-immersed Cris samples P-0 and P-39.1 adsorbed a comparable amount of drug. While there was a statistically significant lower amount of drug adsorbed onto P-78.2 than that adsorbed onto P-39.1 (p P-165.5 > P-331; p HPLC and FTIR analyses showed that ceramics that had higher content of O-Si-O bending (at ~498 cm-1 and ~620 cm-1) bands facilitated Vanc adsorption. On the other hand surfaces with a higher content of nu 4 PO4/O-P-O bending (at ~557 cm-1) and P=O stretching (at ~1343.9 cm-1) bands did not enhance Vanc adsorption. Drug loaded pre-immersed and control non-immersed Cris samples (each 200 mg, n=5 for each sample) were immersed in 2 mL of PBS on an orbital shaker at 37°C, and a 0.5 mL aliquot was removed from the solution and replenished at 1, 3, 6, 8, 24, and 48 hour, and every 48 hour intervals to 22 days thereafter. Drug concentration released from Cris samples after each time point was measured using HPLC. The drug release kinetics demonstrated a statistically significant decrease (p < 0.05) in the cumulative and percent of Vanc released from control non-immersed Cris samples P-0 (1.521 +/- .026 mg; 37.66 +/- .89 %) to P-331 (1.276 +/- .016 mg; 33.46 +/- .77 %) of Vanc, respectively. Additionally, release kinetics also demonstrated statistically significant increase

  1. 12 CFR 347.120 - Computation of investment amounts.

    Science.gov (United States)

    2010-01-01

    ... 12 Banks and Banking 4 2010-01-01 2010-01-01 false Computation of investment amounts. 347.120... GENERAL POLICY INTERNATIONAL BANKING § 347.120 Computation of investment amounts. In computing the amount that may be invested in any foreign organization under §§ 347.117 through 347.119, any investments held...

  2. 29 CFR 4.142 - Contracts in an indefinite amount.

    Science.gov (United States)

    2010-07-01

    ... McNamara-O'Hara Service Contract Act Determining Amount of Contract § 4.142 Contracts in an indefinite amount. (a) Every contract subject to this Act which is indefinite in amount is required to contain the....), a case arising under the Walsh-Healey Public Contracts Act. Such a contract, which may be in the...

  3. 46 CFR 308.303 - Amounts insured under interim binder.

    Science.gov (United States)

    2010-10-01

    ... 308.303 Shipping MARITIME ADMINISTRATION, DEPARTMENT OF TRANSPORTATION EMERGENCY OPERATIONS WAR RISK INSURANCE Second Seamen's War Risk Insurance § 308.303 Amounts insured under interim binder. The amounts insured are the amounts specified in the Second Seamen's War Risk Policy (1955) or as modified by shipping...

  4. Modeling metabolic response to changes of enzyme amount in ...

    African Journals Online (AJOL)

    Based on the work of Hynne et al. (2001), in an in silico model of glycolysis, Saccharomyces cerevisiae is established by introducing an enzyme amount multiple factor (.) into the kinetic equations. The model is aimed to predict the metabolic response to the change of enzyme amount. With the help of .α, the amounts of ...

  5. 7 CFR 1710.107 - Amount lent for acquisitions.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 11 2010-01-01 2010-01-01 false Amount lent for acquisitions. 1710.107 Section 1710... GUARANTEES Loan Purposes and Basic Policies § 1710.107 Amount lent for acquisitions. The maximum amount that will be lent for an acquisition is limited to the value of the property, as determined by RUS. If the...

  6. Kinetics of radiocesium released from contaminated soil by fertilizer solutions

    International Nuclear Information System (INIS)

    Chiang, P.N.; Wang, M.K.; Huang, P.M.; Wang, J.J.

    2008-01-01

    137 Cs is one of the major artificial radionuclides found in environments; but the mechanisms behind fertilizer-induced 137 Cs desorption from soil remain unknown. This study aimed to investigate the kinetics and mechanisms underlying the various cations and anions that cause Cs release from soil under acidic conditions. NH 4 H 2 PO 4 (1 M), 0.5 M (NH 4 ) 2 SO 4 , 1 M NH 4 Cl, 1 M KCl or 1 M NaCl solutions were added to 137 Cs-contaminated soil. The power function model well described the short term 137 Cs desorption with the solutions. The rate coefficients for 137 Cs release from soil in NH 4 H 2 PO 4 , (NH 4 ) 2 SO 4 , NH 4 Cl, and KCl solutions were 7.7, 7.3, 6.8, and 6.1 times higher than the rate observed in a NaCl solution, respectively. The NH 4 H 2 PO 4 and (NH 4 ) 2 SO 4 solutions induced significantly greater 137 Cs release from the contaminated soil than the NH 4 Cl, KCl and NaCl solutions. After four times repeated extractions with the fertilizer solutions, the total amount of 137 Cs extracted by (NH 4 ) 2 SO 4 and NH 4 Cl solutions reached equilibrium, while that extracted using an NH 4 H 2 PO 4 solution continued to increase. The combined effect of phosphate and protons was the major mechanism behind 137 Cs release from contaminated soils, when an NH 4 H 2 PO 4 solution was used

  7. Drug Release Studies from Caesalpinia pulcherrima Seed Polysaccharide.

    Science.gov (United States)

    Jeevanandham, Somasundaram; Dhachinamoorthi, Duraiswamy; Bannoth Chandra Sekhar, Kothapalli

    2011-01-01

    This study examines the controlled release behavior of both water-soluble (acetaminophen, caffeine, theophylline and salicylic acid) and water insoluble (indomethacin) drugs derived from Caesalpinia pulcherrima seed Gum isolated from Caesalpinia pulcherrima kernel powder. It further investigates the effect of incorporating diluents such as microcrystalline cellulose and lactose on caffeine release. In addition the effect the gum's (polysaccharide) partial cross-linking had on release of acetaminophen was examined. Applying the exponential equation, the soluble drugs mechanism of release was found to be anomalous. The insoluble drugs showed a near case II or zero order release mechanism. The rate of release in descending order was caffeine, acetaminophen, theophylline, salicylic acid and indomethacin. An increase in the release kinetics of the drug was observed on blending with diluents. However, the rate of release varied with the type and amount of blend within the matrix. The mechanism of release due to effect of diluents was found to be anomalous. The rate of drug release decreased upon partial cross-linking and the mechanism of release was found to be of super case II.

  8. Preliminary analysis of public dose from CFETR gaseous tritium release

    Energy Technology Data Exchange (ETDEWEB)

    Nie, Baojie [Key Laboratory of Neutronics and Radiation Safety, Institute of Nuclear Energy Safety Technology, Chinese Academy of Sciences, Hefei, Anhui 230031 (China); University of Science and Technology of China, Hefei, Anhui 230027 (China); Ni, Muyi, E-mail: muyi.ni@fds.org.cn [Key Laboratory of Neutronics and Radiation Safety, Institute of Nuclear Energy Safety Technology, Chinese Academy of Sciences, Hefei, Anhui 230031 (China); Lian, Chao; Jiang, Jieqiong [Key Laboratory of Neutronics and Radiation Safety, Institute of Nuclear Energy Safety Technology, Chinese Academy of Sciences, Hefei, Anhui 230031 (China)

    2015-02-15

    Highlights: • Present the amounts and limit dose of tritium release to the environment for CFETR. • Perform a preliminary simulation of radiation dose for gaseous tritium release. • Key parameters about soil types, wind speed, stability class, effective release height and age were sensitivity analyzed. • Tritium release amount is recalculated consistently with dose limit in Chinese regulation for CFETR. - Abstract: To demonstrate tritium self-sufficiency and other engineering issues, the scientific conception of Chinese Fusion Engineering Test Reactor (CFETR) has been proposed in China parallel with ITER and before DEMO reactor. Tritium environmental safety for CFETR is an important issue and must be evaluated because of the huge amounts of tritium cycling in reactor. In this work, different tritium release scenarios of CFETR and dose limit regulations in China are introduced. And the public dose is preliminarily analyzed under normal and accidental events. Furthermore, after finishing the sensitivity analysis of key input parameters, the public dose is reevaluated based on extreme parameters. Finally, tritium release amount is recalculated consistently with the dose limit in Chinese regulation for CFETR, which would provide a reference for tritium system design of CFETR.

  9. Reading motivation, reading amount, and text comprehension in deaf and hearing adults.

    Science.gov (United States)

    Parault, Susan J; Williams, Heather M

    2010-01-01

    The purpose of this study is to examine the relationship between the variables of reading motivation, reading amount, and text comprehension in deaf and hearing adults. Research has shown that less than 50% of deaf students leave high school reading at or above a fourth-grade level (Allen, 1994). Our question is, how does this affect the levels of reading motivation and amount of reading in which deaf adults engage? Assessments of 30 hearing and 24 deaf adults showed that deaf participants reported significantly higher levels of reading motivation despite having been found to read at less than a sixth-grade level. No significant difference in the amount of reading between hearing and deaf adults was found. Amount of reading for personal reasons was found to be the best predictor of text comprehension in the deaf participants, and intrinsic motivation was found to be the best predictor of amount of reading in the deaf participants.

  10. ATP Release Channels

    Directory of Open Access Journals (Sweden)

    Akiyuki Taruno

    2018-03-01

    Full Text Available Adenosine triphosphate (ATP has been well established as an important extracellular ligand of autocrine signaling, intercellular communication, and neurotransmission with numerous physiological and pathophysiological roles. In addition to the classical exocytosis, non-vesicular mechanisms of cellular ATP release have been demonstrated in many cell types. Although large and negatively charged ATP molecules cannot diffuse across the lipid bilayer of the plasma membrane, conductive ATP release from the cytosol into the extracellular space is possible through ATP-permeable channels. Such channels must possess two minimum qualifications for ATP permeation: anion permeability and a large ion-conducting pore. Currently, five groups of channels are acknowledged as ATP-release channels: connexin hemichannels, pannexin 1, calcium homeostasis modulator 1 (CALHM1, volume-regulated anion channels (VRACs, also known as volume-sensitive outwardly rectifying (VSOR anion channels, and maxi-anion channels (MACs. Recently, major breakthroughs have been made in the field by molecular identification of CALHM1 as the action potential-dependent ATP-release channel in taste bud cells, LRRC8s as components of VRACs, and SLCO2A1 as a core subunit of MACs. Here, the function and physiological roles of these five groups of ATP-release channels are summarized, along with a discussion on the future implications of understanding these channels.

  11. Marine fouling release silicone/carbon nanotube nanocomposite coatings: on the importance of the nanotube dispersion state.

    Science.gov (United States)

    Beigbeder, Alexandre; Mincheva, Rosica; Pettitt, Michala E; Callow, Maureen E; Callow, James A; Claes, Michael; Dubois, Philippe

    2010-05-01

    The present work reports on the influence of the dispersion quality of multiwall carbon nanotubes (MWCNTs) in a silicone matrix on the marine fouling-release performance of the resulting nanocomposite coatings. A first set of coatings filled with different nanofiller contents was prepared by the dilution of a silicone/MWCNTs masterbatch within a hydrosilylation-curing polydimethylsiloxane resin. The fouling-release properties of the nanocomposite coatings were studied through laboratory assays with the marine alga (seaweed) Ulva, a common fouling species. As reported previously (see Ref. [19]), the addition of a small (0.05%) amount of carbon nanotubes substantially improves the fouling-release properties of the silicone matrix. This paper shows that this improvement is dependent on the amount of filler, with a maximum obtained with 0.1 wt% of multiwall carbon nanotubes (MWCNTs). The method of dispersion of carbon nanotubes in the silicone matrix is also shown to significantly (p = 0.05) influence the fouling-release properties of the coatings. Dispersing 0.1% MWCNTs using the masterbatch approach yielded coatings with circa 40% improved fouling-release properties over those where MWCNTs were dispersed directly in the polymeric matrix. This improvement is directly related to the state of nanofiller dispersion within the cross-linked silicone coating.

  12. Effect of Laser-assisted and Conventional In-office Bleaching on Monomer Release from Microhybrid and Nanohybrid Composite.

    Science.gov (United States)

    Omrani, Ladan Ranjbar; Farjadfar, Shayan; Pedram, Parham; Sadray, Sima; Kamangar, Sedighe Sadat Hashemi; Chiniforoush, Nasim

    2017-06-30

    Bleaching might affect structural properties of composite materials, and lead to monomer release. This study aimed to evaluate the effect of Laser-assisted and conventional in-office bleaching on the release of BIS-GMA, TEGDMA, and UDMA monomers from a nanohybrid and a microhybrid BIS-GMA based composite. 32 samples of each composite, were divided into 4 subgroups; subgroup 1: Conventional in-office bleaching (CIB) with the Opalescence Boost PF 38% gel, subgroup 2: Laser-assisted bleaching (LBO) with the Opalescence Boost PF 38% gel, subgroup 3: Laser-assisted bleaching (LBH) with the JW Power bleaching gel, subgroup 4: (CO) control without bleaching. All the samples were immersed in tubes of 2cc Ethanol 75% medium. The released monomers were analyzed using the high performance liquid chromatography (HPLC) method 24 h, 7, and 28 days. Data's were analyzed by Univariate Analysis of Variance test followed by Tukeys HSD. The amount of TEGDMA monomer released was not significant. However, nanohybrid composites showed significantly more monomer release than microhybrid composites (P Bleaching by laser with JW Power Bleaching gel led to more monomer release in nanohybrid composite.

  13. Feeding Releases Endogenous Opioids in Humans.

    Science.gov (United States)

    Tuulari, Jetro J; Tuominen, Lauri; de Boer, Femke E; Hirvonen, Jussi; Helin, Semi; Nuutila, Pirjo; Nummenmaa, Lauri

    2017-08-23

    The endogenous opioid system supports a multitude of functions related to appetitive behavior in humans and animals, and it has been proposed to govern hedonic aspects of feeding thus contributing to the development of obesity. Here we used positron emission tomography to investigate whether feeding results in hedonia-dependent endogenous opioid release in humans. Ten healthy males were recruited for the study. They were scanned with the μ-opioid-specific ligand [ 11 C]carfentanil three times, as follows: after a palatable meal, a nonpalatable meal, and after an overnight fast. Subjective mood, satiety, and circulating hormone levels were measured. Feeding induced significant endogenous opioid release throughout the brain. This response was more pronounced following a nonpalatable meal versus a palatable meal, and independent of the subjective hedonic responses to feeding. We conclude that feeding consistently triggers cerebral opioid release even in the absence of subjective pleasure associated with feeding, suggesting that metabolic and homeostatic rather than exclusively hedonic responses play a role in the feeding-triggered cerebral opioid release. SIGNIFICANCE STATEMENT The endogenous opioid system supports both hedonic and homeostatic functions. It has been proposed that overeating and concomitant opioid release could downregulate opioid receptors and promote the development of obesity. However, it remains unresolved whether feeding leads to endogenous opioid release in humans. We used in vivo positron emission tomography to test whether feeding triggers cerebral opioid release and whether this response is associated with pleasurable sensations. We scanned volunteers using the μ-opioid receptor-specific radioligand [ 11 C]carfentanil three times, as follows: after an overnight fast, after consuming a palatable meal, and after consuming a nonpalatable meal. Feeding led to significant endogenous opioid release, and this occurred also in the absence of feeding

  14. Carbon nanotube release from polymers into a food simulant.

    Science.gov (United States)

    Xia, Yining; Uysal Unalan, Ilke; Rubino, Maria; Auras, Rafael

    2017-10-01

    The release assessment of multi-walled carbon nanotubes (CNTs) was performed on two types of polymer-CNT nanocomposites: polypropylene (PP) and polyamide 6 (PA6) containing 3 wt% CNT. Nanocomposite films were prepared and then exposed to ethanol as a fatty-food simulant at 40 °C, and the amount of CNT release into ethanol was determined by ultraviolet-visible spectroscopy (UV-Vis) and graphite furnace atomic absorption spectrometry (GFAAS). The CNTs released into ethanol were visualized by transmission electron microscopy (TEM) and verified by Raman spectroscopy. UV-Vis analysis showed a very small amount of CNT release from the nanocomposite films into ethanol over 60 d: maximum CNT concentrations in ethanol were 1.3 mg/L for the PP-CNT film and 1.2 mg/L for the PA6-CNT film. GFAAS results indicated that the amount of CNTs released into ethanol after 12 d was over 20-fold higher than the results obtained by UV-Vis. Overestimation of CNT release by GFAAS suggested aggregation and poor dispersion of CNTs in the solvent. This assumption was verified by TEM images exhibiting the embedded CNTs in the polymer flakes, which could be poorly dispersed in the solvent. In general, CNT release from the nanocomposite films was considered a surface phenomenon, as indicated by detachment of CNT-containing polymer flakes from the film surface. Copyright © 2017 Elsevier Ltd. All rights reserved.

  15. The in vitro antibiotic release from anti-washout apatite cement using chitosan.

    Science.gov (United States)

    Takechi, Masaaki; Miyamoto, Youji; Momota, Yukihiro; Yuasa, Tetsuya; Tatehara, Seikou; Nagayama, Masaru; Ishikawa, Kunio; Suzuki, Kazuomi

    2002-10-01

    The in vitro antibiotic release from anti-washout apatite cement using chitosan (aw-AC(chi)) was investigated in a preliminary evaluation. Flomoxef sodium was employed as the antibiotic and was incorporated into the powder phase aw-AC(chi) at up to 10%. The setting times were measured for aw-AC(chi) containing various amounts of flomoxef sodium. X-ray diffraction (XRD) analysis was also conducted for the identification of products. To evaluate the drug release profile, set aw-AC was immersed in saline and the released flomoxef sodium was determined at regular intervals. The setting time was prolonged slightly with the addition of flomoxef sodium. The difference at 10% flomoxef sodium (0% vs. 10%) was not significant (p>0.05), and can be negligible in clinic. The XRD analysis revealed that formation of hydroxyapatite (HAP) from aw-AC(chi) was reduced, even after 24 h, when the aw-AC(chi) contained flomoxef sodium at 8% or more. The flomoxef sodium release from aw-AC(chi) showed the typical profile observed in skeleton type drug delivery system (DDS). Changing the concentration of chitosan can control the rate of drug release from aw-AC. Therefore, we conclude that aw-AC(chi) is a good candidate for potential use as a DDS carrier that may be useful in surgical operations.

  16. The estimation of early health effects for different combinations of release parameters and meteorological data

    International Nuclear Information System (INIS)

    Jeong, Jong Tae; Jung, Won Dea

    2001-01-01

    Variations in the number of early health effects resulting from the severe accidents of the YGN 3 and 4 nuclear power plants were examined for different combinations of release parameters and meteorological data. The release parameters and meteorological data were selected in combination to define a limited number of basic spectra characterized by release height, heat content, release time, warning time, wind speed, rainfall rate, and atmospheric stability class. Variant seasonal spectra were also defined in order to estimate the potential significance of seasonal variations as a factor determining the incidence or number of early health effects. The results show that there are large differences in consequences from spectrum to spectrum, although an equal amount and mix of radioactive material is released to the atmosphere in each case. Also, there are large differences in the estimated number of health effects from season to season due to distinct seasonal variations in meteorological combinations in Korea. Therefore, it is necessary to consider seasonal characteristics in developing optimum emergency response strategies

  17. RAVEN Beta Release

    International Nuclear Information System (INIS)

    Rabiti, Cristian; Alfonsi, Andrea; Cogliati, Joshua Joseph; Mandelli, Diego; Kinoshita, Robert Arthur; Wang, Congjian; Maljovec, Daniel Patrick; Talbot, Paul William

    2016-01-01

    This documents the release of the Risk Analysis Virtual Environment (RAVEN) code. A description of the RAVEN code is provided, and discussion of the release process for the M2LW-16IN0704045 milestone. The RAVEN code is a generic software framework to perform parametric and probabilistic analysis based on the response of complex system codes. RAVEN is capable of investigating the system response as well as the input space using Monte Carlo, Grid, or Latin Hyper Cube sampling schemes, but its strength is focused toward system feature discovery, such as limit surfaces, separating regions of the input space leading to system failure, using dynamic supervised learning techniques. RAVEN has now increased in maturity enough for the Beta 1.0 release.

  18. RAVEN Beta Release

    Energy Technology Data Exchange (ETDEWEB)

    Rabiti, Cristian [Idaho National Lab. (INL), Idaho Falls, ID (United States); Alfonsi, Andrea [Idaho National Lab. (INL), Idaho Falls, ID (United States); Cogliati, Joshua Joseph [Idaho National Lab. (INL), Idaho Falls, ID (United States); Mandelli, Diego [Idaho National Lab. (INL), Idaho Falls, ID (United States); Kinoshita, Robert Arthur [Idaho National Lab. (INL), Idaho Falls, ID (United States); Wang, Congjian [Idaho National Lab. (INL), Idaho Falls, ID (United States); Maljovec, Daniel Patrick [Idaho National Lab. (INL), Idaho Falls, ID (United States); Talbot, Paul William [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2016-02-01

    This documents the release of the Risk Analysis Virtual Environment (RAVEN) code. A description of the RAVEN code is provided, and discussion of the release process for the M2LW-16IN0704045 milestone. The RAVEN code is a generic software framework to perform parametric and probabilistic analysis based on the response of complex system codes. RAVEN is capable of investigating the system response as well as the input space using Monte Carlo, Grid, or Latin Hyper Cube sampling schemes, but its strength is focused toward system feature discovery, such as limit surfaces, separating regions of the input space leading to system failure, using dynamic supervised learning techniques. RAVEN has now increased in maturity enough for the Beta 1.0 release.

  19. Guidance for Evaluating the Safety of Experimental Releases of Mosquitoes, Emphasizing Mark-Release-Recapture Techniques.

    Science.gov (United States)

    Benedict, Mark Q; Charlwood, J Derek; Harrington, Laura C; Lounibos, L Philip; Reisen, William K; Tabachnick, Walter J

    2018-01-01

    Experimental releases of mosquitoes are performed to understand characteristics of populations related to the biology, ability to transmit pathogens, and ultimately their control. In this article, we discuss considerations related to the safety of experimental releases of living mosquitoes, applying principles of good practice in vector biology that protect human health and comfort. We describe specific factors of experimental releases of mosquitoes that we believe are critical to inform institutional biosafety committees and similar review boards to which proposals to conduct mosquito release experiments have been submitted. In this study, "experimental releases" means those that do not significantly increase vector capacity or nuisance biting relative to the unperturbed natural baseline. This document specifically does not address releases of mosquitoes for ongoing control programs or trials of new control methods for which broader assessments of risk are required. It also does not address releases of transgenic or exotic (non-native) mosquito species, both of which require particular regulatory approval. Experimental releases may include females and males and evaluation must consider their effects based on the number released, their genotype and phenotype, the environment into which they are released, and postrelease collection activities. We consider whether increases of disease transmission and nuisance biting might result from proposed experimental releases against the backdrop of natural population size variation. We recommend that experimental releases be conducted in a manner that can be reasonably argued to have insignificant negative effects. Reviewers of proposals for experimental releases should expect applicants to provide such an argument based on evidence from similar studies and their planned activities. This document provides guidance for creating and evaluating such proposals.

  20. Gas Release as a Deformation Signal

    Energy Technology Data Exchange (ETDEWEB)

    Bauer, Stephen J. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2017-09-01

    Radiogenic noble gases are contained in crustal rock at inter and intra granular sites. The gas composition depends on lithology, geologic history, fluid phases, and the aging effect by decay of U, Th, and K. The isotopic signature of noble gases found in rocks is vastly different than that of the atmosphere which is contributed by a variety of sources. When rock is subjected to stress conditions exceeding about half its yield strength, micro-cracks begin to form. As rock deformation progresses a fracture network evolves, releasing trapped noble gases and changing the transport properties to gas migration. Thus, changes in gas emanation and noble gas composition from rocks could be used to infer changes in stress-state and deformation. The purpose of this study has been to evaluate the effect of deformation/strain rate upon noble gas release. Four triaxial experiments were attempted for a strain rate range of %7E10-8 /s (180,000s) to %7E 10-4/s (500s); the three fully successful experiments (at the faster strain rates) imply the following: (1) helium is measurably released for all strain rates during deformation, this release is in amounts 1-2 orders of magnitude greater than that present in the air, and (2) helium gas release increases with decreasing strain rate.

  1. Choosing the right amount of healthcare information technologies investments.

    Science.gov (United States)

    Meyer, Rodolphe; Degoulet, Patrice

    2010-04-01

    Choosing and justifying the right amount of investment in healthcare information technologies (HITECH or HIT) in hospitals is an ever increasing challenge. Our objectives are to assess the financial impact of HIT on hospital outcome, and propose decision-helping tools that could be used to rationalize the distribution of hospital finances. We used a production function and microeconomic tools on data of 21 Paris university hospitals recorded from 1998 to 2006 to compute the elasticity coefficients of HIT versus non-HIT capital and labor as regards to hospital financial outcome and optimize the distribution of investments according to the productivity associated with each input. HIT inputs and non-HIT inputs both have a positive and significant impact on hospital production (elasticity coefficients respectively of 0.106 and 0.893; R(2) of 0.92). We forecast 2006 results from the 1998 to 2005 dataset with an accuracy of +0.61%. With the model used, the best proportion of HIT investments was estimated to be 10.6% of total input and this was predicted to lead to a total saving of 388 million Euros for the 2006 dataset. Considering HIT investment from the point of view of a global portfolio and applying econometric and microeconomic tools allow the required confidence level to be attained for choosing the right amount of HIT investments. It could also allow hospitals using these tools to make substantial savings, and help them forecast their choices for the following year for better HITECH governance in the current stimulation context. (c) 2010 Elsevier Ireland Ltd. All rights reserved.

  2. Testing Significance Testing

    Directory of Open Access Journals (Sweden)

    Joachim I. Krueger

    2018-04-01

    Full Text Available The practice of Significance Testing (ST remains widespread in psychological science despite continual criticism of its flaws and abuses. Using simulation experiments, we address four concerns about ST and for two of these we compare ST’s performance with prominent alternatives. We find the following: First, the 'p' values delivered by ST predict the posterior probability of the tested hypothesis well under many research conditions. Second, low 'p' values support inductive inferences because they are most likely to occur when the tested hypothesis is false. Third, 'p' values track likelihood ratios without raising the uncertainties of relative inference. Fourth, 'p' values predict the replicability of research findings better than confidence intervals do. Given these results, we conclude that 'p' values may be used judiciously as a heuristic tool for inductive inference. Yet, 'p' values cannot bear the full burden of inference. We encourage researchers to be flexible in their selection and use of statistical methods.

  3. Safety significance evaluation system

    International Nuclear Information System (INIS)

    Lew, B.S.; Yee, D.; Brewer, W.K.; Quattro, P.J.; Kirby, K.D.

    1991-01-01

    This paper reports that the Pacific Gas and Electric Company (PG and E), in cooperation with ABZ, Incorporated and Science Applications International Corporation (SAIC), investigated the use of artificial intelligence-based programming techniques to assist utility personnel in regulatory compliance problems. The result of this investigation is that artificial intelligence-based programming techniques can successfully be applied to this problem. To demonstrate this, a general methodology was developed and several prototype systems based on this methodology were developed. The prototypes address U.S. Nuclear Regulatory Commission (NRC) event reportability requirements, technical specification compliance based on plant equipment status, and quality assurance assistance. This collection of prototype modules is named the safety significance evaluation system

  4. Predicting significant torso trauma.

    Science.gov (United States)

    Nirula, Ram; Talmor, Daniel; Brasel, Karen

    2005-07-01

    Identification of motor vehicle crash (MVC) characteristics associated with thoracoabdominal injury would advance the development of automatic crash notification systems (ACNS) by improving triage and response times. Our objective was to determine the relationships between MVC characteristics and thoracoabdominal trauma to develop a torso injury probability model. Drivers involved in crashes from 1993 to 2001 within the National Automotive Sampling System were reviewed. Relationships between torso injury and MVC characteristics were assessed using multivariate logistic regression. Receiver operating characteristic curves were used to compare the model to current ACNS models. There were a total of 56,466 drivers. Age, ejection, braking, avoidance, velocity, restraints, passenger-side impact, rollover, and vehicle weight and type were associated with injury (p < 0.05). The area under the receiver operating characteristic curve (83.9) was significantly greater than current ACNS models. We have developed a thoracoabdominal injury probability model that may improve patient triage when used with ACNS.

  5. Carbon nanotube release from polymers into a food simulant

    International Nuclear Information System (INIS)

    Xia, Yining; Uysal Unalan, Ilke; Rubino, Maria; Auras, Rafael

    2017-01-01

    The release assessment of multi-walled carbon nanotubes (CNTs) was performed on two types of polymer-CNT nanocomposites: polypropylene (PP) and polyamide 6 (PA6) containing 3 wt% CNT. Nanocomposite films were prepared and then exposed to ethanol as a fatty-food simulant at 40 °C, and the amount of CNT release into ethanol was determined by ultraviolet-visible spectroscopy (UV-Vis) and graphite furnace atomic absorption spectrometry (GFAAS). The CNTs released into ethanol were visualized by transmission electron microscopy (TEM) and verified by Raman spectroscopy. UV-Vis analysis showed a very small amount of CNT release from the nanocomposite films into ethanol over 60 d: maximum CNT concentrations in ethanol were 1.3 mg/L for the PP-CNT film and 1.2 mg/L for the PA6-CNT film. GFAAS results indicated that the amount of CNTs released into ethanol after 12 d was over 20-fold higher than the results obtained by UV-Vis. Overestimation of CNT release by GFAAS suggested aggregation and poor dispersion of CNTs in the solvent. This assumption was verified by TEM images exhibiting the embedded CNTs in the polymer flakes, which could be poorly dispersed in the solvent. In general, CNT release from the nanocomposite films was considered a surface phenomenon, as indicated by detachment of CNT-containing polymer flakes from the film surface. - Highlights: • Release of CNT from polypropylene and polyamide nanocomposites were quantified and validated with TEM and Raman. • Spectroscopy and silane-labeled CNT were used for tracking the release of CNT. • The release behavior of CNT from nanocomposites was mostly generated from the polymer surfaces.

  6. Muscle glycogen storage after different amounts of carbohydrate ingestion.

    Science.gov (United States)

    Ivy, J L; Lee, M C; Brozinick, J T; Reed, M J

    1988-11-01

    The purpose of this study was to determine whether the rate of muscle glycogen storage could be enhanced during the initial 4-h period postexercise by substantially increasing the amount of the carbohydrate consumed. Eight subjects cycled for 2 h on three separate occasions to deplete their muscle glycogen stores. Immediately and 2 h after exercise they consumed either 0 (P), 1.5 (L), or 3.0 g glucose/kg body wt (H) from a 50% glucose polymer solution. Blood samples were drawn from an antecubital vein before exercise, during exercise, and throughout recovery. Muscle biopsies were taken from the vastus lateralis immediately, 2 h, and 4 h after exercise. Blood glucose and insulin declined significantly during exercise in each of the three treatments. They remained below the preexercise concentrations during recovery in the P treatment but increased significantly above the preexercise concentrations during the L and H treatments. By the end of the 4 h-recovery period, blood glucose and insulin were still significantly above the preexercise concentrations in both treatments. Muscle glycogen storage was significantly increased above the basal rate (P, 0.5 mumol.g wet wt-1.h-1) after ingestion of either glucose polymer supplement. The rates of muscle glycogen storage, however, were not different between the L and H treatments during the first 2 h (L, 5.2 +/- 0.9 vs. H, 5.8 +/- 0.7 mumol.g wet wt-1.h-1) or the second 2 h of recovery (L, 4.0 +/- 0.9 vs. H, 4.5 +/- 0.6 mumol.g wet wt-1. h-1).(ABSTRACT TRUNCATED AT 250 WORDS)

  7. Hydraulic release oil tool

    International Nuclear Information System (INIS)

    Mims, M.G.; Mueller, M.D.; Ehlinger, J.C.

    1992-01-01

    This patent describes a hydraulic release tool. It comprises a setting assembly; a coupling member for coupling to drill string or petroleum production components, the coupling member being a plurality of sockets for receiving the dogs in the extended position and attaching the coupling member the setting assembly; whereby the setting assembly couples to the coupling member by engagement of the dogs in the sockets of releases from and disengages the coupling member in movement of the piston from its setting to its reposition in response to a pressure in the body in exceeding the predetermined pressure; and a relief port from outside the body into its bore and means to prevent communication between the relief port and the bore of the body axially of the piston when the piston is in the setting position and to establish such communication upon movement of the piston from the setting position to the release position and reduce the pressure in the body bore axially of the piston, whereby the reduction of the pressure signals that the tool has released the coupling member

  8. APASS Data Release 10

    Science.gov (United States)

    Henden, Arne A.; Levine, Stephen; Terrell, Dirk; Welch, Douglas L.; Munari, Ulisse; Kloppenborg, Brian K.

    2018-06-01

    The AAVSO Photometric All-Sky Survey (APASS) has been underway since 2010. This survey covers the entire sky from 7.5 knowledge of the optical train distortions. With these changes, DR10 includes many more stars than prior releases. We describe the survey, its remaining limitations, and prospects for the future, including a very-bright-star extension.

  9. Release the Prisoners Game

    Science.gov (United States)

    Van Hecke, Tanja

    2011-01-01

    This article presents the mathematical approach of the optimal strategy to win the "Release the prisoners" game and the integration of this analysis in a math class. Outline lesson plans at three different levels are given, where simulations are suggested as well as theoretical findings about the probability distribution function and its mean…

  10. Tumor significant dose

    International Nuclear Information System (INIS)

    Supe, S.J.; Nagalaxmi, K.V.; Meenakshi, L.

    1983-01-01

    In the practice of radiotherapy, various concepts like NSD, CRE, TDF, and BIR are being used to evaluate the biological effectiveness of the treatment schedules on the normal tissues. This has been accepted as the tolerance of the normal tissue is the limiting factor in the treatment of cancers. At present when various schedules are tried, attention is therefore paid to the biological damage of the normal tissues only and it is expected that the damage to the cancerous tissues would be extensive enough to control the cancer. Attempt is made in the present work to evaluate the concent of tumor significant dose (TSD) which will represent the damage to the cancerous tissue. Strandquist in the analysis of a large number of cases of squamous cell carcinoma found that for the 5 fraction/week treatment, the total dose required to bring about the same damage for the cancerous tissue is proportional to T/sup -0.22/, where T is the overall time over which the dose is delivered. Using this finding the TSD was defined as DxN/sup -p/xT/sup -q/, where D is the total dose, N the number of fractions, T the overall time p and q are the exponents to be suitably chosen. The values of p and q are adjusted such that p+q< or =0.24, and p varies from 0.0 to 0.24 and q varies from 0.0 to 0.22. Cases of cancer of cervix uteri treated between 1978 and 1980 in the V. N. Cancer Centre, Kuppuswamy Naidu Memorial Hospital, Coimbatore, India were analyzed on the basis of these formulations. These data, coupled with the clinical experience, were used for choice of a formula for the TSD. Further, the dose schedules used in the British Institute of Radiology fraction- ation studies were also used to propose that the tumor significant dose is represented by DxN/sup -0.18/xT/sup -0.06/

  11. New Environmentalconditions Responsible for the amount of mg Incorporated in Biogenic Carbonates

    Science.gov (United States)

    Zuddas, P.; Cherchi, A.; DeGiudici, G. B.; Buosi, C.

    2012-12-01

    The composition of carbonate minerals formed in past and present oceans is assumed to be significantly controlled by temperature and seawater composition. Several kinetic laboratory investigations have suggested that the temperature is kinetically responsible for the amount of Mg incorporated in both abiotic and biogenic calcites and that variation of kinetic reaction mechanism resulting from the temperature changes are correlated with the variable amount of Mg incorporated in calcites. These results explain why in present-day marine carbonates low-Mg calcite cements are mainly associated with cool water while high-Mg carbonates are dominantly found in warm-water environments. An apparent inverse relationship between the global average paleo-temperature and the Mg/Ca ratio is however observed in the past formed marine carbonate. This apparent contradiction has been interpreted as resulting from a possible changing in the relative seawater geochemical cycles of these cations. Recent monitoring of costal areas in presence of heavy metals and CO2 released from industrial polluted area reveals the presence of porcelanaceous miliolids infested by microscopic boring microflora (cyanobacteria, algae and fungi). Here, benthonic foraminifera have Mg/Ca molar ratio by one order of magnitude higher when compared to the average value of the same genus living under uncontaminated environments. A similar behaviour has been found for Zn, Cd and Pb. In these contaminated environments, temperature and average major seawater composition remain constant, while PCO2 partial pressure (estimated by pH and alkalinity using the ion pairing model) is 3-5 times higher than the average for the open sea nearby. Geochemical models predicts that CO2 increase is affecting carbonate saturation state of surface water in the twenty-first century indicating that calcareous organisms may have difficulty calcifying leading to production of weaker skeletons and greater vulnerability to erosion. The

  12. Diffusion rates for elevated releases

    International Nuclear Information System (INIS)

    Ramsdell, J.V.

    1983-11-01

    A search of the literature related to diffusion from elevated sources has determined that an adequate data base exists for use in developing parameterizations for estimating diffusion rates for material released from free standing stacks at nuclear power plants. A review of published data analyses indicates that a new parameterization of horizontal diffusion rates specifically for elevated releases is not likely to significantly change the magnitudes of horizontal diffusion coefficients on the average. However, the uncertainties associated with horizontal diffusion coefficient estimates under any given set of atmospheric conditions could be reduced by a new parameterization. Similarly, a new parameterization of vertical diffusion rates would be unlikely to significantly alter the magnitudes of diffusion coefficients for unstable atmospheric conditons. However, for neutral and stable atmospheric conditions, a new parameterization of vertical diffusion rates might increase vertical diffusion coefficients significantly. The increase would move ground-level time-integrated concentration maxima closer to the plant and would increase the maxima. 55 references, 2 figures, 4 tables

  13. Uranium chemistry: significant advances

    International Nuclear Information System (INIS)

    Mazzanti, M.

    2011-01-01

    The author reviews recent progress in uranium chemistry achieved in CEA laboratories. Like its neighbors in the Mendeleev chart uranium undergoes hydrolysis, oxidation and disproportionation reactions which make the chemistry of these species in water highly complex. The study of the chemistry of uranium in an anhydrous medium has led to correlate the structural and electronic differences observed in the interaction of uranium(III) and the lanthanides(III) with nitrogen or sulfur molecules and the effectiveness of these molecules in An(III)/Ln(III) separation via liquid-liquid extraction. Recent work on the redox reactivity of trivalent uranium U(III) in an organic medium with molecules such as water or an azide ion (N 3 - ) in stoichiometric quantities, led to extremely interesting uranium aggregates particular those involved in actinide migration in the environment or in aggregation problems in the fuel processing cycle. Another significant advance was the discovery of a compound containing the uranyl ion with a degree of oxidation (V) UO 2 + , obtained by oxidation of uranium(III). Recently chemists have succeeded in blocking the disproportionation reaction of uranyl(V) and in stabilizing polymetallic complexes of uranyl(V), opening the way to to a systematic study of the reactivity and the electronic and magnetic properties of uranyl(V) compounds. (A.C.)

  14. Meaning and significance of

    Directory of Open Access Journals (Sweden)

    Ph D Student Roman Mihaela

    2011-05-01

    Full Text Available The concept of "public accountability" is a challenge for political science as a new concept in this area in full debate and developement ,both in theory and practice. This paper is a theoretical approach of displaying some definitions, relevant meanings and significance odf the concept in political science. The importance of this concept is that although originally it was used as a tool to improve effectiveness and eficiency of public governance, it has gradually become a purpose it itself. "Accountability" has become an image of good governance first in the United States of America then in the European Union.Nevertheless,the concept is vaguely defined and provides ambiguous images of good governance.This paper begins with the presentation of some general meanings of the concept as they emerge from specialized dictionaries and ancyclopaedies and continues with the meanings developed in political science. The concept of "public accontability" is rooted in economics and management literature,becoming increasingly relevant in today's political science both in theory and discourse as well as in practice in formulating and evaluating public policies. A first conclusin that emerges from, the analysis of the evolution of this term is that it requires a conceptual clarification in political science. A clear definition will then enable an appropriate model of proving the system of public accountability in formulating and assessing public policies, in order to implement a system of assessment and monitoring thereof.

  15. Nuclear operator. Liability amounts and financial security limits

    International Nuclear Information System (INIS)

    2015-07-01

    This paper gives, for numerous countries involved (or would be involved) in nuclear activities, financial information on the liability amount imposed on the operator, the amounts provided from public funds beyond the Operator's Liability Amount, to be made available by the State in whose territory the nuclear installation of the liable operator is situated, and the public funds contributed jointly by all the States parties to the BSC or CSC according to a pre-determined formula

  16. Significant Radionuclides Determination

    Energy Technology Data Exchange (ETDEWEB)

    Jo A. Ziegler

    2001-07-31

    The purpose of this calculation is to identify radionuclides that are significant to offsite doses from potential preclosure events for spent nuclear fuel (SNF) and high-level radioactive waste expected to be received at the potential Monitored Geologic Repository (MGR). In this calculation, high-level radioactive waste is included in references to DOE SNF. A previous document, ''DOE SNF DBE Offsite Dose Calculations'' (CRWMS M&O 1999b), calculated the source terms and offsite doses for Department of Energy (DOE) and Naval SNF for use in design basis event analyses. This calculation reproduces only DOE SNF work (i.e., no naval SNF work is included in this calculation) created in ''DOE SNF DBE Offsite Dose Calculations'' and expands the calculation to include DOE SNF expected to produce a high dose consequence (even though the quantity of the SNF is expected to be small) and SNF owned by commercial nuclear power producers. The calculation does not address any specific off-normal/DBE event scenarios for receiving, handling, or packaging of SNF. The results of this calculation are developed for comparative analysis to establish the important radionuclides and do not represent the final source terms to be used for license application. This calculation will be used as input to preclosure safety analyses and is performed in accordance with procedure AP-3.12Q, ''Calculations'', and is subject to the requirements of DOE/RW-0333P, ''Quality Assurance Requirements and Description'' (DOE 2000) as determined by the activity evaluation contained in ''Technical Work Plan for: Preclosure Safety Analysis, TWP-MGR-SE-000010'' (CRWMS M&O 2000b) in accordance with procedure AP-2.21Q, ''Quality Determinations and Planning for Scientific, Engineering, and Regulatory Compliance Activities''.

  17. Twenty-six years of post-release monitoring of Florida manatees (Trichechus manatus latirostris): evaluation of a cooperative rehabilitation program

    Science.gov (United States)

    Adimey, Nicole M.; Ross, Monica; Hall, Madison; Reid, James P.; Barlas, Margie E.; Keith Diagne, Lucy W; Bonde, Robert K.

    2016-01-01

    The rescue, rehabilitation, and release of Florida manatees (Trichechus manatus latirostris) into the wild has occurred since 1974; however, a comprehensive evaluation of the outcomes of the releases has never been conducted. Herein, we examined data for 136 Florida manatees that were rehabilitated and released with telemetry tags between 1988 and 2013 to determine release outcome of each individual as either success (acclimation) or failure after at least 1 y. Ten predictor variables were statistically evaluated for potential relationships to release outcome. To assess the contribution of each predictor variable to release outcome, each variable was tested for significance in univariate analyses. Manatees born in captivity experienced poor success after release (14%), whereas the overall success of wild-born individuals was higher (72%). When compared with other variables in our dataset, number of days in captivity was the strongest predictor for determining success. Manatees rescued as calves and held in captivity for more than 5 y had a high likelihood of failure, while subadults and adults had a high likelihood of success, regardless of the amount of time spent in captivity. Ensuring the success of individual manatees after release is critical for evaluating the contribution of the manatee rehabilitation program to the growth of the wild population.

  18. Composite poly(vinyl alcohol/poly(vinyl acetate electrospun nanofibrous mats as a novel wound dressing matrix for controlled release of drugs

    Directory of Open Access Journals (Sweden)

    Jannesari M

    2011-05-01

    Full Text Available Marziyeh Jannesari1, Jaleh Varshosaz2, Mohammad Morshed1, Maedeh Zamani11Department of Textile Engineering, Isfahan University of Technology, Isfahan, Iran; 2Department of Pharmaceutics, School of Pharmacy and Pharmaceutical Sciences Research Center, Isfahan University of Medical Sciences, Isfahan, IranAbstract: The aim of this study was to develop novel biomedicated nanofiber electrospun mats for controlled drug release, especially drug release directly to an injury site to accelerate wound healing. Nanofibers of poly(vinyl alcohol (PVA, poly(vinyl acetate (PVAc, and a 50:50 composite blend, loaded with ciprofloxacin HCl (CipHCl, were successfully prepared by an electrospinning technique for the first time. The morphology and average diameter of the electrospun nanofibers were investigated by scanning electron microscopy. X-ray diffraction studies indicated an amorphous distribution of the drug inside the nanofiber blend. Introducing the drug into polymeric solutions significantly decreased solution viscosities as well as nanofiber diameter. In vitro drug release evaluations showed that both the kind of polymer and the amount of drug loaded greatly affected the degree of swelling, weight loss, and initial burst and rate of drug release. Blending PVA and PVAc exhibited a useful and convenient method for electrospinning in order to control the rate and period of drug release in wound healing applications. Also, the thickness of the blend nanofiber mats strongly influenced the initial release and rate of drug release.Keywords: biodegradable polymers, drug delivery, controlled release, electrospun nanofibers, wound dressing

  19. Secondary effects of anion exchange on chloride, sulfate, and lead release: systems approach to corrosion control.

    Science.gov (United States)

    Willison, Hillary; Boyer, Treavor H

    2012-05-01

    Water treatment processes can cause secondary changes in water chemistry that alter finished water quality including chloride, sulfate, natural organic matter (NOM), and metal release. Hence, the goal of this research was to provide an improved understanding of the chloride-to-sulfate mass ratio (CSMR) with regards to chloride and sulfate variations at full-scale water treatment plants and corrosion potential under simulated premise plumbing conditions. Laboratory corrosion studies were conducted using Pb-Sn solder/Cu tubing galvanic cells exposed to model waters with low (approx. 5 mg/L Cl(-) and 10 mg/L SO(4)(2-)) and high (approx. 50 mg/L Cl(-) and 100 mg/L SO(4)(2-)) concentrations of chloride and sulfate at a constant CSMR of ≈ 0.5. The role of NOM during corrosion was also evaluated by changing the type of organic material. In addition, full-scale sampling was conducted to quantify the raw water variability of chloride, sulfate, and NOM concentrations and the changes to these parameters from magnetic ion exchange treatment. Test conditions with higher concentrations of chloride and sulfate released significantly more lead than the lower chloride and sulfate test waters. In addition, the source of NOM was a key factor in the amount of lead released with the model organic compounds yielding significantly less lead release than aquatic NOM. Copyright © 2012 Elsevier Ltd. All rights reserved.

  20. "The blood pressure and dermal sensitivity effects of Nylon hollow fiber releasing Glycerin Trinitrate in vivo "

    Directory of Open Access Journals (Sweden)

    "Ostad SN

    2002-09-01

    Full Text Available In order to improve patient's compliance in taking glycerine trinitrate (GTN nylon hollow fiber which has been successfully used for release of chlorhexidine diacetate and levonorgestrel was employed to make nylon hollow fiber releasing GTN. Hollow nylon fibres of external diameter 0.63 mm, 75 mm long with an internal capacity of 16 μl, were filled with GTN (190 mg/ml in 70% ethanol (v/v or vehicle alone and the ends were heat-sealed. The fibers were then immersed in 10 ml of 0.9% (w/v saline in a separating funnel. The GTN release pattern from fiber, the effect of the product on blood pressure and its potential dermal toxicity were assessed. The release of GTN from the fibres was approximately 2.7 μg/min when the fibres contained 16 mg of drug. The results showed that the amount of GTN within the single fibre was enough to reduce blood pressure significantly, while it did not show significant dermal toxicity. It is concluded that GTN fiber, if used as monofilament, is not an alternative method for GTN delivery.

  1. Degassing, gas retention and release in Fe(0) permeable reactive barriers.

    Science.gov (United States)

    Ruhl, Aki S; Jekel, Martin

    2014-04-01

    Corrosion of Fe(0) has been successfully utilized for the reductive treatment of multiple contaminants. Under anaerobic conditions, concurrent corrosion leads to the generation of hydrogen and its liberation as a gas. Gas bubbles are mobile or trapped within the irregular pore structure leading to a reduction of the water filled pore volume and thus decreased residence time and permeability (gas clogging). With regard to the contaminant transport to the reactive site, the estimation of surface properties of the reactive material indicated that individual gas bubbles only occupied minor contact areas of the reactive surface. Quantification of gas entrapment by both gravimetrical and tracer investigations revealed that development of preferential flow paths was not significant. A novel continuous gravimetrical method was implemented to record variations in gas entrapment and gas bubble releases from the reactive filling. Variation of grain size fractions revealed that the pore geometry had a significant impact on gas release. Large pores led to the release of comparably large gas amounts while smaller volumes were released from finer pores with a higher frequency. Relevant processes are explained with a simplified pictorial sequence that incorporates relevant mechanisms. Copyright © 2014 Elsevier B.V. All rights reserved.

  2. Significant incidents in nuclear fuel cycle facilities

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    In contrast to nuclear power plants, events in nuclear fuel cycle facilities are not well documented. The INES database covers all the nuclear fuel cycle facilities; however, it was developed in the early 1990s and does not contain information on events prior to that. The purpose of the present report is to collect significant events and analyze them in order to give a safety related overview of nuclear fuel cycle facilities. Significant incidents were selected using the following criteria: release of radioactive material or exposure to radiation; degradation of items important to safety; and deficiencies in design, quality assurance, etc. which include criticality incidents, fire, explosion, radioactive release and contamination. This report includes an explanation, where possible, of root causes, lessons learned and action taken. 4 refs, 4 tabs.

  3. Significant incidents in nuclear fuel cycle facilities

    International Nuclear Information System (INIS)

    1996-03-01

    In contrast to nuclear power plants, events in nuclear fuel cycle facilities are not well documented. The INES database covers all the nuclear fuel cycle facilities; however, it was developed in the early 1990s and does not contain information on events prior to that. The purpose of the present report is to collect significant events and analyze them in order to give a safety related overview of nuclear fuel cycle facilities. Significant incidents were selected using the following criteria: release of radioactive material or exposure to radiation; degradation of items important to safety; and deficiencies in design, quality assurance, etc. which include criticality incidents, fire, explosion, radioactive release and contamination. This report includes an explanation, where possible, of root causes, lessons learned and action taken. 4 refs, 4 tabs

  4. STUDIES ON THE PATHOGENESIS OF FEVER. 13. THE EFFECT OF PHAGOCYTOSIS ON THE RELEASE OF ENDOGENOUS PYROGEN BY POLYMORPHONUCLEAR LEUKOCYTES.

    Science.gov (United States)

    BERLIN, R D; WOOD, W B

    1964-05-01

    1. Phagocytosis promotes the release of endogenous pyrogen from polymorphonuclear leucocytes. 2. The release of pyrogen, though initiated by the phagocytic event, is not synchronous with it. 3. The postphagocytic release mechanism is not inhibited by sodium fluoride and, therefore, appears not to require continued production of energy by the cell. 4. The release process, on the other hand, is inhibited by arsenite, suggesting the participation of one or more sulfhydryl-dependent enzymes in the over-all reaction. 5. Particle for particle, the ingestion of heat-killed rough pneumococci causes the release of approximately 100 times as much pyrogen as the ingestion of polystyrene beads of the same size. 6. The pyrogen release mechanism of polymorphonuclear leucocytes separated directly from blood, unlike that of granulocytes in acute inflammatory exudates, is not readily activated by incubation of the cells in K-free saline. Despite this difference, both blood and exudate leucocytes following phagocytosis release large amounts of pyrogen, even in the presence of K(+). The fact that the postphagocytic reaction is uninhibited by the concentrations of K(+) which are present in plasma and extracellular fluids, suggests that this mechanism of pyrogen release may well operate in vivo. 7. As might be expected from the foregoing observations, the intravenous injection of a sufficiently large number of heat-killed pneumococci causes fever in the intact host. Intravenously injected polystyrene beads, on the other hand, are significantly less pyrogenic. Evidence is presented to support the conclusion that the fever in both instances is caused by pyrogen released from the circulating leucocytes which have phagocyted the injected particles. 8. The possible relationships of these findings to the pathogenesis of fevers caused by acute bacterial infections are discussed.

  5. Decomposition and particle release of a carbon nanotube/epoxy nanocomposite at elevated temperatures

    Energy Technology Data Exchange (ETDEWEB)

    Schlagenhauf, Lukas [Empa - Swiss Federal Laboratories for Materials Science and Technology, Laboratory for Functional Polymers (Switzerland); Kuo, Yu-Ying; Bahk, Yeon Kyoung [Empa - Swiss Federal Laboratories for Materials Science and Technology, Laboratory for Advanced Analytical Technologies (Switzerland); Nüesch, Frank [Empa - Swiss Federal Laboratories for Materials Science and Technology, Laboratory for Functional Polymers (Switzerland); Wang, Jing, E-mail: Jing.Wang@ifu.baug.ethz.ch [Empa - Swiss Federal Laboratories for Materials Science and Technology, Laboratory for Advanced Analytical Technologies (Switzerland)

    2015-11-15

    Carbon nanotubes (CNTs) as fillers in nanocomposites have attracted significant attention, and one of the applications is to use the CNTs as flame retardants. For such nanocomposites, possible release of CNTs at elevated temperatures after decomposition of the polymer matrix poses potential health threats. We investigated the airborne particle release from a decomposing multi-walled carbon nanotube (MWCNT)/epoxy nanocomposite in order to measure a possible release of MWCNTs. An experimental set-up was established that allows decomposing the samples in a furnace by exposure to increasing temperatures at a constant heating rate and under ambient air or nitrogen atmosphere. The particle analysis was performed by aerosol measurement devices and by transmission electron microscopy (TEM) of collected particles. Further, by the application of a thermal denuder, it was also possible to measure non-volatile particles only. Characterization of the tested samples and the decomposition kinetics were determined by the usage of thermogravimetric analysis (TGA). The particle release of different samples was investigated, of a neat epoxy, nanocomposites with 0.1 and 1 wt% MWCNTs, and nanocomposites with functionalized MWCNTs. The results showed that the added MWCNTs had little effect on the decomposition kinetics of the investigated samples, but the weight of the remaining residues after decomposition was influenced significantly. The measurements with decomposition in different atmospheres showed a release of a higher number of particles at temperatures below 300 °C when air was used. Analysis of collected particles by TEM revealed that no detectable amount of MWCNTs was released, but micrometer-sized fibrous particles were collected.

  6. Decomposition and particle release of a carbon nanotube/epoxy nanocomposite at elevated temperatures

    International Nuclear Information System (INIS)

    Schlagenhauf, Lukas; Kuo, Yu-Ying; Bahk, Yeon Kyoung; Nüesch, Frank; Wang, Jing

    2015-01-01

    Carbon nanotubes (CNTs) as fillers in nanocomposites have attracted significant attention, and one of the applications is to use the CNTs as flame retardants. For such nanocomposites, possible release of CNTs at elevated temperatures after decomposition of the polymer matrix poses potential health threats. We investigated the airborne particle release from a decomposing multi-walled carbon nanotube (MWCNT)/epoxy nanocomposite in order to measure a possible release of MWCNTs. An experimental set-up was established that allows decomposing the samples in a furnace by exposure to increasing temperatures at a constant heating rate and under ambient air or nitrogen atmosphere. The particle analysis was performed by aerosol measurement devices and by transmission electron microscopy (TEM) of collected particles. Further, by the application of a thermal denuder, it was also possible to measure non-volatile particles only. Characterization of the tested samples and the decomposition kinetics were determined by the usage of thermogravimetric analysis (TGA). The particle release of different samples was investigated, of a neat epoxy, nanocomposites with 0.1 and 1 wt% MWCNTs, and nanocomposites with functionalized MWCNTs. The results showed that the added MWCNTs had little effect on the decomposition kinetics of the investigated samples, but the weight of the remaining residues after decomposition was influenced significantly. The measurements with decomposition in different atmospheres showed a release of a higher number of particles at temperatures below 300 °C when air was used. Analysis of collected particles by TEM revealed that no detectable amount of MWCNTs was released, but micrometer-sized fibrous particles were collected

  7. Decomposition and particle release of a carbon nanotube/epoxy nanocomposite at elevated temperatures

    Science.gov (United States)

    Schlagenhauf, Lukas; Kuo, Yu-Ying; Bahk, Yeon Kyoung; Nüesch, Frank; Wang, Jing

    2015-11-01

    Carbon nanotubes (CNTs) as fillers in nanocomposites have attracted significant attention, and one of the applications is to use the CNTs as flame retardants. For such nanocomposites, possible release of CNTs at elevated temperatures after decomposition of the polymer matrix poses potential health threats. We investigated the airborne particle release from a decomposing multi-walled carbon nanotube (MWCNT)/epoxy nanocomposite in order to measure a possible release of MWCNTs. An experimental set-up was established that allows decomposing the samples in a furnace by exposure to increasing temperatures at a constant heating rate and under ambient air or nitrogen atmosphere. The particle analysis was performed by aerosol measurement devices and by transmission electron microscopy (TEM) of collected particles. Further, by the application of a thermal denuder, it was also possible to measure non-volatile particles only. Characterization of the tested samples and the decomposition kinetics were determined by the usage of thermogravimetric analysis (TGA). The particle release of different samples was investigated, of a neat epoxy, nanocomposites with 0.1 and 1 wt% MWCNTs, and nanocomposites with functionalized MWCNTs. The results showed that the added MWCNTs had little effect on the decomposition kinetics of the investigated samples, but the weight of the remaining residues after decomposition was influenced significantly. The measurements with decomposition in different atmospheres showed a release of a higher number of particles at temperatures below 300 °C when air was used. Analysis of collected particles by TEM revealed that no detectable amount of MWCNTs was released, but micrometer-sized fibrous particles were collected.

  8. Development and evaluation of sustained release losartan potassium matrix tablet using kollidon SR as release retardant

    Directory of Open Access Journals (Sweden)

    Shahid Sarwar

    2012-12-01

    Full Text Available The present study was undertaken to develop sustained release (SR matrix tablets of losartan potassium, an angiotensin-II antagonist for the treatment of hypertension. The tablets were prepared by direct compression method, along with Kollidon SR as release retardant polymer. The amount of losartan potassium remains fixed (100 mg for all the three formulations whereas the amounts of Kollidon SR were 250 mg, 225 mg, and 200 mg for F-1, F-2, and F-3 respectively. The evaluation involves three stages: the micromeritic properties evaluation of granules, physical property studies of tablets, and in-vitro release kinetics studies. The USP apparatus type II was selected to perform the dissolution test, and the dissolution medium was 900 mL phosphate buffer pH 6.8. The test was carried out at 75 rpm, and the temperature was maintained at 37 ºC ± 0.5 ºC. The release kinetics was analyzed using several kinetics models. Higher polymeric content in the matrix decreased the release rate of drug. At lower polymeric level, the rate and extent of drug release were enhanced. All the formulations followed Higuchi release kinetics where the Regression co-efficient (R² values are 0.958, 0.944, and 0.920 for F-1, F-2, and F-3 respectively, and they exhibited diffusion dominated drug release. Statistically significant (PO presente estudo foi realizado para desenvolver (SR matriz de comprimidos de liberação sustentada de losartana, um antagonista da angiotensina II, para o tratamento da hipertensão arterial. Os comprimidos foram preparados pelo método de compressão direta com Kollidon SR como polímero de liberação lenta. A quantidade de losartana potássica permanece fixa (100 mg para todas as três formulações enquanto que as quantidades de Kollidon SR foram de 250 mg, 225 mg e 200 mg para F-1, F-2 e F-3, respectivamente. A avaliação envolve três etapas- propriedades micromeríticas dos grânulos, estudo das propriedades físicas dos comprimidos e

  9. The load and release characteristics on a strong cationic ion-exchange fiber: kinetics, thermodynamics, and influences.

    Science.gov (United States)

    Yuan, Jing; Gao, Yanan; Wang, Xinyu; Liu, Hongzhuo; Che, Xin; Xu, Lu; Yang, Yang; Wang, Qifang; Wang, Yan; Li, Sanming

    2014-01-01

    Ion-exchange fibers were different from conventional ion-exchange resins in their non-cross-linked structure. The exchange was located on the surface of the framework, and the transport resistance reduced significantly, which might mean that the exchange is controlled by an ionic reaction instead of diffusion. Therefore, this work aimed to investigate the load and release characteristics of five model drugs with the strong cationic ion-exchange fiber ZB-1. Drugs were loaded using a batch process and released in United States Pharmacopoeia (USP) dissolution apparatus 2. Opposing exchange kinetics, suitable for the special structure of the fiber, were developed for describing the exchange process with the help of thermodynamics, which illustrated that the load was controlled by an ionic reaction. The molecular weight was the most important factor to influence the drug load and release rate. Strong alkalinity and rings in the molecular structures made the affinity between the drug and fiber strong, while logP did not cause any profound differences. The drug-fiber complexes exhibited sustained release. Different kinds and concentrations of counter ions or different amounts of drug-fiber complexes in the release medium affected the release behavior, while the pH value was independent of it. The groundwork for in-depth exploration and further application of ion-exchange fibers has been laid.

  10. Heat release rate from the combustion of uranium

    International Nuclear Information System (INIS)

    Solbrig, C.W.

    1995-01-01

    Fuel treatment is planned at the Argonne National Laboratory on EBR-II spent fuel. The electrochemical treatment process is carried out in a cell with an argon atmosphere to prevent any reaction. The amount of fuel processed at any time is limited by the amount of energy which could be released by metal combustion if air is inadvertently allowed into the cell since the heat release would increase the cell pressure. The cell pressure is required to be below atmospheric even if combustion occurs to ensure no cell gas/aerosol is released to the environment. Metal fires can release large amounts of heat. In certain configurations such as fine particulate, metal can be pyrophoric at room temperature. When the metal is a nuclear fuel, it is important to be able to predict the reaction/heat release rate if the metal is inadvertently exposed to air. A realistic combustion model is needed to predict heat release rates for the many different flow and transport configurations which exist in the various fuel processing steps. A model for the combustion of uranium is developed here which compares satisfactorily to experimental data

  11. 5 CFR 870.704 - Amount of Option A.

    Science.gov (United States)

    2010-01-01

    ... 5 Administrative Personnel 2 2010-01-01 2010-01-01 false Amount of Option A. 870.704 Section 870... of Option A. (a) The amount of Option A coverage an annuitant or compensationer can continue is $10,000. (b) An annuitant's or compensationer's Option A coverage reduces by 2 percent of the original...

  12. 24 CFR 232.565 - Maximum loan amount.

    Science.gov (United States)

    2010-04-01

    ... URBAN DEVELOPMENT MORTGAGE AND LOAN INSURANCE PROGRAMS UNDER NATIONAL HOUSING ACT AND OTHER AUTHORITIES MORTGAGE INSURANCE FOR NURSING HOMES, INTERMEDIATE CARE FACILITIES, BOARD AND CARE HOMES, AND ASSISTED... Fire Safety Equipment Eligible Security Instruments § 232.565 Maximum loan amount. The principal amount...

  13. 39 CFR 601.111 - Interest on claim amounts.

    Science.gov (United States)

    2010-07-01

    ... that date is later, until the date of payment. Simple interest will be paid at the rate established by... 39 Postal Service 1 2010-07-01 2010-07-01 false Interest on claim amounts. 601.111 Section 601.111... PROPERTY RIGHTS OTHER THAN PATENTS PURCHASING OF PROPERTY AND SERVICES § 601.111 Interest on claim amounts...

  14. 22 CFR 226.73 - Collection of amounts due.

    Science.gov (United States)

    2010-04-01

    ... 22 Foreign Relations 1 2010-04-01 2010-04-01 false Collection of amounts due. 226.73 Section 226.73 Foreign Relations AGENCY FOR INTERNATIONAL DEVELOPMENT ADMINISTRATION OF ASSISTANCE AWARDS TO U.S. NON-GOVERNMENTAL ORGANIZATIONS After-the-Award Requirements § 226.73 Collection of amounts due. (a...

  15. Potentiometric determination of milligram amounts of uranium by semiautomatic titrator

    International Nuclear Information System (INIS)

    Ryzhinskij, M.V.; Stepanov, A.V.; Preobrazhenskaya, L.D.; Solntseva, L.F.; Gromova, E.A.

    1978-01-01

    A semiautomatic titrator is described which allows gravimetriotentiometricc-p titrat mg amounts of substances. Milligram amounts of uranium (absolute contents and oxygen/uranium ratio) in U 3 O 8 were determined as an example of the titrator action. The relative standard deviation was less than 0.001

  16. 12 CFR 209.4 - Amounts and payments.

    Science.gov (United States)

    2010-01-01

    ... CANCELLATION OF FEDERAL RESERVE BANK CAPITAL STOCK (REGULATION I) § 209.4 Amounts and payments. (a) Amount of... lesser of 15 percent or 100 shares of its Reserve Bank capital stock, it shall file with the appropriate Reserve Bank an application for issue or cancellation of Reserve Bank capital stock in order to adjust its...

  17. 45 CFR 1225.11 - Amount of attorney fees.

    Science.gov (United States)

    2010-10-01

    ... 45 Public Welfare 4 2010-10-01 2010-10-01 false Amount of attorney fees. 1225.11 Section 1225.11... § 1225.11 Amount of attorney fees. (a) When a decision of the agency provides for an award of attorney's fees or costs, the complainant's attorney shall submit a verified statement of costs and attorney's...

  18. 46 CFR 282.20 - Amount of subsidy payable.

    Science.gov (United States)

    2010-10-01

    ... Rates. Daily ODS rates shall be used to quantify the amount of ODS payable. The daily ODS rate... items is the daily amount of ODS payable for approved vessel operating days, excluding reduced crew... the daily wage ODS rate to conform to the complement remaining on the vessel. The man-day reduction...

  19. 29 CFR 530.302 - Amounts of civil money penalties.

    Science.gov (United States)

    2010-07-01

    ... 29 Labor 3 2010-07-01 2010-07-01 false Amounts of civil money penalties. 530.302 Section 530.302... EMPLOYMENT OF HOMEWORKERS IN CERTAIN INDUSTRIES Civil Money Penalties § 530.302 Amounts of civil money penalties. (a) A civil money penalty, not to exceed $500 per affected homeworker for any one violation, may...

  20. 42 CFR 438.704 - Amounts of civil money penalties.

    Science.gov (United States)

    2010-10-01

    ... 42 Public Health 4 2010-10-01 2010-10-01 false Amounts of civil money penalties. 438.704 Section... SERVICES (CONTINUED) MEDICAL ASSISTANCE PROGRAMS MANAGED CARE Sanctions § 438.704 Amounts of civil money penalties. (a) General rule. The limit on, or the maximum civil money penalty the State may impose varies...

  1. 20 CFR 362.12 - Computation of amount of reimbursement.

    Science.gov (United States)

    2010-04-01

    ... 20 Employees' Benefits 1 2010-04-01 2010-04-01 false Computation of amount of reimbursement. 362.12 Section 362.12 Employees' Benefits RAILROAD RETIREMENT BOARD INTERNAL ADMINISTRATION, POLICY AND... the cost of repair is the amount payable. (b) Depreciation in value of an item of personal property is...

  2. 28 CFR 70.73 - Collection of amounts due.

    Science.gov (United States)

    2010-07-01

    ... 28 Judicial Administration 2 2010-07-01 2010-07-01 false Collection of amounts due. 70.73 Section 70.73 Judicial Administration DEPARTMENT OF JUSTICE (CONTINUED) UNIFORM ADMINISTRATIVE REQUIREMENTS... OTHER NON-PROFIT ORGANIZATIONS After-the-Award Requirements § 70.73 Collection of amounts due. (a) Any...

  3. Atmospheric Release Advisory Capability

    International Nuclear Information System (INIS)

    Dickerson, M.H.; Gudiksen, P.H.; Sullivan, T.J.

    1983-02-01

    The Atmospheric Release Advisory Capability (ARAC) project is a Department of Energy (DOE) sponsored real-time emergency response service available for use by both federal and state agencies in case of a potential or actual atmospheric release of nuclear material. The project, initiated in 1972, is currently evolving from the research and development phase to full operation. Plans are underway to expand the existing capability to continuous operation by 1984 and to establish a National ARAC Center (NARAC) by 1988. This report describes the ARAC system, its utilization during the past two years, and plans for its expansion during the next five to six years. An integral part of this expansion is due to a very important and crucial effort sponsored by the Defense Nuclear Agency to extend the ARAC service to approximately 45 Department of Defense (DOD) sites throughout the continental US over the next three years

  4. Border cell release

    DEFF Research Database (Denmark)

    Mravec, Jozef

    2017-01-01

    Plant border cells are specialised cells derived from the root cap with roles in the biomechanics of root growth and in forming a barrier against pathogens. The mechanism of highly localised cell separation which is essential for their release to the environment is little understood. Here I present...... in situ analysis of Brachypodium distachyon, a model organism for grasses which possess type II primary cell walls poor in pectin content. Results suggest similarity in spatial dynamics of pectic homogalacturonan during dicot and monocot border cell release. Integration of observations from different...... species leads to the hypothesis that this process most likely does not involve degradation of cell wall material but rather employs unique cell wall structural and compositional means enabling both the rigidity of the root cap as well as detachability of given cells on its surface....

  5. Energy released in fission

    International Nuclear Information System (INIS)

    James, M.F.

    1969-05-01

    The effective energy released in and following the fission of U-235, Pu-239 and Pu-241 by thermal neutrons, and of U-238 by fission spectrum neutrons, is discussed. The recommended values are: U-235 ... 192.9 ± 0.5 MeV/fission; U-238 ... 193.9 ± 0.8 MeV/fission; Pu-239 ... 198.5 ± 0.8 MeV/fission; Pu-241 ... 200.3 ± 0.8 MeV/fission. These values include all contributions except from antineutrinos and very long-lived fission products. The detailed contributions are discussed, and inconsistencies in the experimental data are pointed out. In Appendix A, the contribution to the total useful energy release in a reactor from reactions other than fission are discussed briefly, and in Appendix B there is a discussion of the variations in effective energy from fission with incident neutron energy. (author)

  6. Released air during vapor and air cavitation

    Energy Technology Data Exchange (ETDEWEB)

    Jablonská, Jana, E-mail: jana.jablonska@vsb.cz; Kozubková, Milada, E-mail: milada.kozubkova@vsb.cz [VŠB-Technical University of Ostrava, Faculty of Mechanical Engineering, Department of Hydromechanics and Hydraulic Equipment, 17. listopadu 15, 708 33 Ostrava-Poruba (Czech Republic)

    2016-06-30

    Cavitation today is a very important problem that is solved by means of experimental and mathematical methods. The article deals with the generation of cavitation in convergent divergent nozzle of rectangular cross section. Measurement of pressure, flow rate, temperature, amount of dissolved air in the liquid and visualization of cavitation area using high-speed camera was performed for different flow rates. The measurement results were generalized by dimensionless analysis, which allows easy detection of cavitation in the nozzle. For numerical simulation the multiphase mathematical model of cavitation consisting of water and vapor was created. During verification the disagreement with the measurements for higher flow rates was proved, therefore the model was extended to multiphase mathematical model (water, vapor and air), due to release of dissolved air. For the mathematical modeling the multiphase turbulence RNG k-ε model for low Reynolds number flow with vapor and air cavitation was used. Subsequently the sizes of the cavitation area were verified. In article the inlet pressure and loss coefficient depending on the amount of air added to the mathematical model are evaluated. On the basis of the approach it may be create a methodology to estimate the amount of released air added at the inlet to the modeled area.

  7. EIA new releases

    International Nuclear Information System (INIS)

    1994-12-01

    This report was prepared by the Energy Information Administration. It contains news releases on items of interest to the petroleum, coal, nuclear, electric and alternate fuels industries ranging from economic outlooks to environmental concerns. There is also a listing of reports by industry and an energy education resource listing containing sources for free or low-cost energy-related educational materials for educators and primary and secondary students

  8. Atmospheric release advisory capability

    International Nuclear Information System (INIS)

    Sullivan, T.J.

    1981-01-01

    The ARAC system (Atmospheric Release Advisory Capability) is described. The system is a collection of people, computers, computer models, topographic data and meteorological input data that together permits a calculation of, in a quasi-predictive sense, where effluent from an accident will migrate through the atmosphere, where it will be deposited on the ground, and what instantaneous and integrated dose an exposed individual would receive

  9. Controlled release effervescent buccal discs of buspirone hydrochloride: in vitro and in vivo evaluation studies.

    Science.gov (United States)

    Jaipal, A; Pandey, M M; Charde, S Y; Sadhu, N; Srinivas, A; Prasad, R G

    2016-01-01

    In the present study controlled release effervescent buccal discs of buspirone hydrochloride (BS) were designed using HPMC as rate controlling and bioadhesive polymer by direct compression method. Sodium bicarbonate and citric acid were used in varying amounts as effervescence forming agents. Carbon dioxide evolved due to reaction of sodium bicarbonate and citric acid was explored for its potential as buccal permeation enhancer. The designed buccal discs were evaluated for physical characteristics and in vitro drug release studies. Bioadhesive behavior of designed buccal discs was assessed using texture analyzer. In vivo animal studies were performed in rabbits to study bioavailability of BS in the designed buccal discs and to establish permeation enhancement ability of carbon dioxide. It was observed that effervescent buccal discs have faster drug release compared to non-effervescent buccal discs in vitro and effervescent buccal discs demonstrated significant increase in bioavailability of drug when compared to non-effervescent formulation. Hence, effervescent buccal discs can be used as an alternative to improve the drug permeation resulting in better bioavailability. However, the amount of acid and base used for generation of carbon dioxide should be selected with care as this may damage the integrity of bioadhesive dosage form.

  10. Use of plasma creatine kinase pharmacokinetics to estimate the amount of excercise-induced muscle damage in Beagles.

    Science.gov (United States)

    Chanoit, G P; Lefebvre, H P; Orcel, K; Laroute, V; Toutain, P L; Braun, J P

    2001-09-01

    To assess the effects of moderate exercise on plasma creatine kinase (CK) pharmacokinetics and to estimate exercise-induced muscle damage in dogs. 6 untrained adult Beagles. The study was divided into 3 phases. In phase 1, dogs ran for 1 hour at a speed of 9 km/h, and samples were used to determine the area under the plasma CK activity versus time curve (AUC) induced by exercise. In phases 2 and 3, pharmacokinetics of CK were calculated in dogs during exercise and at rest, respectively. Values for AUC and plasma clearance (CI) were used to estimate muscle damage. At rest, values for Cl, steady-state volume of distribution (Vdss), and mean retention time (MRT) were 0.32+/-0.02 ml/kg of body weight/min, 57+/-173 ml/kg, and 3.0+/-0.57 h, respectively. During exercise, Cl decreased significantly (0.26+/-0.03 ml/kg/min), MRT increased significantly, (4.4+/-0.97 h), and Vdss remained unchanged. Peak of plasma CK activity (151+/-58.8 U/L) was observed 3 hours after completion of exercise. Estimated equivalent amount of muscle corresponding to the quantity of CK released was 41+/-29.3 mg/kg. These results revealed that exercise had a minor effect on CK disposition and that the equivalent amount of muscle damaged by moderate exercise was negligible. This study illustrates the relevance for use of the minimally invasive and quantitative pharmacokinetic approach when estimating muscle damage.

  11. Contact: Releasing the news

    Science.gov (United States)

    Pinotti, Roberto

    The problem of mass behavior after man's future contacts with other intelligences in the universe is not only a challenge for social scientists and political leaders all over the world, but also a cultural time bomb as well. In fact, since the impact of CETI (Contact with Extraterrestrial Intelligence) on human civilization, with its different cultures, might cause a serious socio-anthropological shock, a common and predetermined worldwide strategy is necessary in releasing the news after the contact, in order to keep possible manifestations of fear, panic and hysteria under control. An analysis of past studies in this field and of parallel historical situations as analogs suggests a definite "authority crisis" in the public as a direct consequence of an unexpected release of the news, involving a devastating "chain reaction" process (from both the psychological and sociological viewpoints) of anomie and maybe the collapse of today's society. The only way to prevent all this is to prepare the world's public opinion concerning contact before releasing the news, and to develop a long-term strategy through the combined efforts of scientists, political leaders, intelligence agencies and the mass media, in order to create the cultural conditions in which a confrontation with ETI won't affect mankind in a traumatic way. Definite roles and tasks in this multi-level model are suggested.

  12. Noble Gas Release Signal as a Precursor to Fracture

    Science.gov (United States)

    Bauer, S. J.; Lee, H.; Gardner, W. P.

    2017-12-01

    We present empirical results of rock strain, microfracturing, acoustic emissions, and noble gas release from laboratory triaxial experiments for a granite, basalt, shale and bedded rock salt. Noble gases are released and measured real-time during deformation using mass spectrometry. The gas release represents a precursive signal to macrofracture. Gas release is associated with increased acoustic emissions indicating that microfracturing is required to release gas and create pathways for the gas to be sensed. The gas released depends on initial gas content, pore structure and its evolution during deformation, the deformation amount, matrix permeability, deformation style and the stress/strain history. Gases are released from inter and intracrystalline sites; release rate increases as strain and microfracturing increases. The gas composition depends on lithology, geologic history and age, fluids present, and radioisotope concentrations that affect radiogenic noble gas isotope (e.g. 4He,40Ar) production. Noble gas emission and its relationship to crustal processes such as seismicity and volcanism, tectonic velocities, qualitative estimates of deep permeability, age dating of groundwater, and a signature of nuclear weapon detonation. Our result show that mechanical deformation of crustal materials is an important process controlling gas release from rocks and minerals, and should be considered in techniques which utilize gas release and/or accumulation. We propose using noble gas release to signal rock deformation in boreholes, mines and waste repositories. We postulate each rock exhibits a gas release signature which is microstructure, stress, strain, and/or permanent deformation dependent. Calibration of such relationships, for example relating gas release per rock unit volume to strain may be used to quantify rock deformation and develop predictive models.Sandia National Laboratories is a multimission laboratory managed and operated by National Technology and

  13. Studies on the Biological Effects of Ozone: 10. Release of Factors from Ozonated Human Platelets

    Directory of Open Access Journals (Sweden)

    G. Valacchi

    1999-01-01

    Full Text Available In a previous work we have shown that heparin, in the presence of ozone (O3, promotes a dose-dependent platelet aggregation, while after Ca2+ chelation with citrate, platelet aggregation is almost negligible. These results led us to think that aggregation may enhance the release of platelet components. We have here shown that indeed significantly higher amount of platelet-derived growth factor (PDGF, transforming growth factor β1 (TGF-β1 and interleukin-8(IL-8 are released in a dose-dependent manner after ozonation of heparinised platelet-rich plasma samples. These findings may explain the enhanced healing of torpid ulcers in patients with chronic limbischemia treated with O3 autohaemoteraphy (O3-AHT.

  14. Determining the amount of waste plastics in the feed of Austrian waste-to-energy facilities

    OpenAIRE

    Schwarzb?ck, Therese; Van Eygen, Emile; Rechberger, Helmut; Fellner, Johann

    2016-01-01

    Although thermal recovery of waste plastics is widely practiced in many European countries, reliable information on the amount of waste plastics in the feed of waste-to-energy plants is rare. In most cases the amount of plastics present in commingled waste, such as municipal solid waste, commercial, or industrial waste, is estimated based on a few waste sorting campaigns, which are of limited significance with regard to the characterisation of plastic flows. In the present study, an alternati...

  15. Release of mineral ions in dental plaque following acid production.

    Science.gov (United States)

    Tanaka, M; Margolis, H C

    1999-03-01

    The release of appreciable amounts of calcium, phosphate and fluoride found in whole plaque into the plaque-fluid phase, following bacterial acid production, can potentially reduce the driving force for tooth demineralization. However, limited information is available on this topic, particularly on the release of fluoride. This study sought to determine the change in calcium, phosphate and fluoride concentrations in plaque fluid after sucrose exposure. 48 h overnight-fasted supragingival plaque samples were collected from all tooth surfaces (with the exception of the lower lingual anterior teeth) of one half of an individual mouth, following a 1 min water rinse. Plaque samples were then collected from the other half of the same mouth, following a 292 mM sucrose rinse. Plaque fluid was isolated by centrifugation and analysed for total calcium and phosphate (ion chromatography) and for free fluoride (ion-specific electrode). Samples were collected from seven individuals. Following sucrose exposure, plaque-fluid pH decreased significantly from 6.5+/- 0.3 to 5.4+/-0.2; calcium concentrations (mmol/l) also increased significantly (p Fluoride and phosphate concentrations in plaque fluid, however, did not increase significantly after sucrose exposure: mean concentrations (mmol/l) of fluoride after the water and sucrose rinses were 0.006+/-0.003 and 0.005+/-0.002, respectively, and mean phosphate concentrations (mmol/l) were 11.0+/-2.0 and 12.0+/-3.0, respectively. When results were expressed per wet plaque weight, phosphate concentrations were also found to increase significantly. The same trends were observed when additional plaque samples were treated in vitro with sucrose: fluoride-ion activity did not increase in plaque under in vivo-like conditions.

  16. An evaluation of two types of nickel-titanium wires in terms of micromorphology and nickel ions' release following oral environment exposure.

    Science.gov (United States)

    Ghazal, Abdul Razzak A; Hajeer, Mohammad Y; Al-Sabbagh, Rabab; Alghoraibi, Ibrahim; Aldiry, Ahmad

    2015-01-01

    This study aimed to compare superelastic and heat-activated nickel-titanium orthodontic wires' surface morphology and potential release of nickel ions following exposure to oral environment conditions. Twenty-four 20-mm-length distal cuts of superelastic (NiTi Force I®) and 24 20-mm-length distal cuts of heat-activated (Therma-Ti Lite®) nickel-titanium wires (American Orthodontics, Sheboygan, WI, USA) were divided into two equal groups: 12 wire segments left unused and 12 segments passively exposed to oral environment for 1 month. Scanning electron microscopy and atomic force microscopy were used to analyze surface morphology of the wires which were then immersed in artificial saliva for 1 month to determine potential nickel ions' release by means of atomic absorption spectrophotometer. Heat-activated nickel-titanium (NiTi) wires were rougher than superelastic wires, and both types of wires released almost the same amount of Ni ions. After clinical exposure, more surface roughness was recorded for superelastic NiTi wires and heat-activated NiTi wires. However, retrieved superelastic NiTi wires released less Ni ions in artificial saliva after clinical exposure, and the same result was recorded regarding heat-activated wires. Both types of NiTi wires were obviously affected by oral environment conditions; their surface roughness significantly increased while the amount of the released Ni ions significantly declined.

  17. Protecting privacy in data release

    CERN Document Server

    Livraga, Giovanni

    2015-01-01

    This book presents a comprehensive approach to protecting sensitive information when large data collections are released by their owners. It addresses three key requirements of data privacy: the protection of data explicitly released, the protection of information not explicitly released but potentially vulnerable due to a release of other data, and the enforcement of owner-defined access restrictions to the released data. It is also the first book with a complete examination of how to enforce dynamic read and write access authorizations on released data, applicable to the emerging data outsou

  18. Triggered Release from Polymer Capsules

    Energy Technology Data Exchange (ETDEWEB)

    Esser-Kahn, Aaron P. [Univ. of Illinois, Urbana, IL (United States). Beckman Inst. for Advanced Science and Technology and Dept. of Chemistry; Odom, Susan A. [Univ. of Illinois, Urbana, IL (United States). Beckman Inst. for Advanced Science and Technology and Dept. of Chemistry; Sottos, Nancy R. [Univ. of Illinois, Urbana, IL (United States). Beckman Inst. for Advanced Science and Technology and Dept. of Materials Science and Engineering; White, Scott R. [Univ. of Illinois, Urbana, IL (United States). Beckman Inst. for Advanced Science and Technology and Dept. of Aerospace Engineering; Moore, Jeffrey S. [Univ. of Illinois, Urbana, IL (United States). Beckman Inst. for Advanced Science and Technology and Dept. of Chemistry

    2011-07-06

    Stimuli-responsive capsules are of interest in drug delivery, fragrance release, food preservation, and self-healing materials. Many methods are used to trigger the release of encapsulated contents. Here we highlight mechanisms for the controlled release of encapsulated cargo that utilize chemical reactions occurring in solid polymeric shell walls. Triggering mechanisms responsible for covalent bond cleavage that result in the release of capsule contents include chemical, biological, light, thermal, magnetic, and electrical stimuli. We present methods for encapsulation and release, triggering methods, and mechanisms and conclude with our opinions on interesting obstacles for chemically induced activation with relevance for controlled release.

  19. Metal release from coffee machines and electric kettles.

    Science.gov (United States)

    Müller, Frederic D; Hackethal, Christin; Schmidt, Roman; Kappenstein, Oliver; Pfaff, Karla; Luch, Andreas

    2015-01-01

    The release of elemental ions from 8 coffee machines and 11 electric kettles into food simulants was investigated. Three different types of coffee machines were tested: portafilter espresso machines, pod machines and capsule machines. All machines were tested subsequently on 3 days before and on 3 days after decalcification. Decalcification of the machines was performed with agents according to procedures as specified in the respective manufacturer's manuals. The electric kettles showed only a low release of the elements analysed. For the coffee machines decreasing concentrations of elements were found from the first to the last sample taken in the course of 1 day. Metal release on consecutive days showed a decreasing trend as well. After decalcification a large increase in the amounts of elements released was encountered. In addition, the different machine types investigated clearly differed in their extent of element release. By far the highest leaching, both quantitatively and qualitatively, was found for the portafilter machines. With these products releases of Pb, Ni, Mn, Cr and Zn were in the range and beyond the release limits as proposed by the Council of Europe. Therefore, a careful rinsing routine, especially after decalcification, is recommended for these machines. The comparably lower extent of release of one particular portafilter machine demonstrates that metal release at levels above the threshold that triggers health concerns are technically avoidable.

  20. 26 CFR 1.465-20 - Treatment of amounts borrowed from certain persons and amounts protected against loss.

    Science.gov (United States)

    2010-04-01

    ... not increase the taxpayer's amount at risk because they are borrowed from a person who has an interest in the activity other than that of a creditor or from a person who is related to a person (other than the taxpayer) who has an interest in the activity other than that of a creditor; and (2) Amounts...

  1. Arsenic readily released to pore waters from buried mill tailings

    Energy Technology Data Exchange (ETDEWEB)

    Mahoney, John [Hydrologic Consultants, Inc., 143 Union Blvd., Suite 525, Lakewood, CO 80228 (United States)]. E-mail: jmahoney@hcico.com; Langmuir, Donald [Hydrochem Systems Corp., P.O. Box 17090, Golden, CO 80402 (United States); Gosselin, Neil [Department of Chemistry and Biochemistry, University of Regina, 3737 Wascana Way, Regina, SK, S4S 0A2 (Canada); Rowson, John [COGEMA Resources, Inc., P.O. Box 9204, Saskatoon, SK, S7K 3X5 (Canada)

    2005-05-15

    At the McClean Lake Operation in the Athabasca Basin of northern Saskatchewan, the untreated acid raffinate solutions associated with U mill tailings contain up to 700 mg/L dissolved As. To reduce the concentration of As and other contaminants in acid tailing slurries at the JEB mill at McClean Lake, ferric sulfate may be added to the acid raffinates to assure that their molar Fe/As ratio equals or exceeds 3. Tailings slurries are then neutralized with lime to pH 4, and subsequently to pH 7-8. The neutralized tailings contain minerals from the original ore, which are chiefly quartz, illite, kaolinite and chlorite, and precipitated (secondary) minerals that include gypsum, scorodite, annabergite, hydrobasaluminite and ferrihydrite. Most of the As is associated with the secondary arsenate minerals, scorodite and annabergite. However, a few percent is adsorbed and/or co-precipitated, mainly by ferrihydrite. Of major concern to provincial and federal regulators is the risk that significant amounts of As might be released from the tailings to pore waters after their subaqueous disposal in the tailings management facility. A laboratory study was performed to address this issue, measuring readily desorbed As using a method known as equilibrium partitioning in closed systems (EPICS). The EPICS method was selected because it employs a leaching solution that, except for its As concentration, is identical in composition to the neutralized raffinate in contact with the tailings. Laboratory experiments and modeling results demonstrated that the As that could be readily released to pore waters is about 0.2% of the total As in the tailings. Long-term, such releases may contribute no more than a few mg/L of dissolved As to tailings pore waters.

  2. Arsenic readily released to pore waters from buried mill tailings

    International Nuclear Information System (INIS)

    Mahoney, John; Langmuir, Donald; Gosselin, Neil; Rowson, John

    2005-01-01

    At the McClean Lake Operation in the Athabasca Basin of northern Saskatchewan, the untreated acid raffinate solutions associated with U mill tailings contain up to 700 mg/L dissolved As. To reduce the concentration of As and other contaminants in acid tailing slurries at the JEB mill at McClean Lake, ferric sulfate may be added to the acid raffinates to assure that their molar Fe/As ratio equals or exceeds 3. Tailings slurries are then neutralized with lime to pH 4, and subsequently to pH 7-8. The neutralized tailings contain minerals from the original ore, which are chiefly quartz, illite, kaolinite and chlorite, and precipitated (secondary) minerals that include gypsum, scorodite, annabergite, hydrobasaluminite and ferrihydrite. Most of the As is associated with the secondary arsenate minerals, scorodite and annabergite. However, a few percent is adsorbed and/or co-precipitated, mainly by ferrihydrite. Of major concern to provincial and federal regulators is the risk that significant amounts of As might be released from the tailings to pore waters after their subaqueous disposal in the tailings management facility. A laboratory study was performed to address this issue, measuring readily desorbed As using a method known as equilibrium partitioning in closed systems (EPICS). The EPICS method was selected because it employs a leaching solution that, except for its As concentration, is identical in composition to the neutralized raffinate in contact with the tailings. Laboratory experiments and modeling results demonstrated that the As that could be readily released to pore waters is about 0.2% of the total As in the tailings. Long-term, such releases may contribute no more than a few mg/L of dissolved As to tailings pore waters

  3. Potential risks of TiO{sub 2} and ZnO nanoparticles released from sunscreens into outdoor swimming pools

    Energy Technology Data Exchange (ETDEWEB)

    Jeon, Soo-kyung [Center for Water Resource Cycle, Green City Technology Institute, Korea Institute of Science and Technology (KIST), Seoul 136-791 (Korea, Republic of); Energy Environment Policy and Technology, Green School, Korea University (KU)-Korea Institute of Science and Technology (KIST), Seoul 136-701 (Korea, Republic of); Kim, Eun-ju [Center for Water Resource Cycle, Green City Technology Institute, Korea Institute of Science and Technology (KIST), Seoul 136-791 (Korea, Republic of); Lee, Jaesang [Energy Environment Policy and Technology, Green School, Korea University (KU)-Korea Institute of Science and Technology (KIST), Seoul 136-701 (Korea, Republic of); Civil, Environmental, and Architectural Engineering, Korea University, Seoul 136-701 (Korea, Republic of); Lee, Seunghak, E-mail: seunglee@kist.re.kr [Center for Water Resource Cycle, Green City Technology Institute, Korea Institute of Science and Technology (KIST), Seoul 136-791 (Korea, Republic of); Energy Environment Policy and Technology, Green School, Korea University (KU)-Korea Institute of Science and Technology (KIST), Seoul 136-701 (Korea, Republic of)

    2016-11-05

    Highlights: • Nanoparticles from sunscreen products can be released into public pools. • Nanoparticles and organic ingredients can generate reactive oxygen species (ROS). • A negative impact of ROS should not be significant in swimming pool. - Abstract: The potential risks of nanoparticles (NPs) in sunscreens being released into swimming water were evaluated by a series of laboratory experiments simulating the fate and transport of NPs in outdoor swimming pools. NPs released from sunscreen-applied skin were estimated using pig skins covered with five different commercial sunscreens containing TiO{sub 2}, ZnO, or both at various concentrations. Assuming that the swimming water treatment processes consisted of filtration, UV irradiation, heating, and chlorination, possible removal of the released NPs by each process was estimated. Generation of hydrogen peroxide (H{sub 2}O{sub 2}) by the NPs under sunlight and after UV photochemical treatment were measured, and the H{sub 2}O{sub 2} concentration possibly present in the swimming pool was calculated based on some specific scenarios of operating an outdoor swimming pool. It was found that a significant amount of the NPs in sunscreens could be released into the swimming water, and accumulate during circulation through the treatment system. However, the concentration of H{sub 2}O{sub 2} possibly present in the swimming pool should be below the level at which an adverse effect to bathers is concerned.

  4. Gamma-amino butyric acid (GABA) release in the ciliated protozoon Paramecium occurs by neuronal-like exocytosis.

    Science.gov (United States)

    Ramoino, P; Milanese, M; Candiani, S; Diaspro, A; Fato, M; Usai, C; Bonanno, G

    2010-04-01

    Paramecium primaurelia expresses a significant amount of gamma-amino butyric acid (GABA). Paramecia possess both glutamate decarboxylase (GAD)-like and vesicular GABA transporter (vGAT)-like proteins, indicating the ability to synthesize GABA from glutamate and to transport GABA into vesicles. Using antibodies raised against mammalian GAD and vGAT, bands with an apparent molecular weight of about 67 kDa and 57 kDa were detected. The presence of these bands indicated a similarity between the proteins in Paramecium and in mammals. VAMP, syntaxin and SNAP, putative proteins of the release machinery that form the so-called SNARE complex, are present in Paramecium. Most VAMP, syntaxin and SNAP fluorescence is localized in spots that vary in size and density and are primarily distributed near the plasma membrane. Antibodies raised against mammal VAMP-3, sintaxin-1 or SNAP-25 revealed protein immunoblot bands having molecular weights consistent with those observed in mammals. Moreover, P. primaurelia spontaneously releases GABA into the environment, and this neurotransmitter release significantly increases after membrane depolarization. The depolarization-induced GABA release was strongly reduced not only in the absence of extracellular Ca(2+) but also by pre-incubation with bafilomycin A1 or with botulinum toxin C1 serotype. It can be concluded that GABA occurs in Paramecium, where it is probably stored in vesicles capable of fusion with the cell membrane; accordingly, GABA can be released from Paramecium by stimulus-induced, neuronal-like exocytotic mechanisms.

  5. Potential risks of TiO_2 and ZnO nanoparticles released from sunscreens into outdoor swimming pools

    International Nuclear Information System (INIS)

    Jeon, Soo-kyung; Kim, Eun-ju; Lee, Jaesang; Lee, Seunghak

    2016-01-01

    Highlights: • Nanoparticles from sunscreen products can be released into public pools. • Nanoparticles and organic ingredients can generate reactive oxygen species (ROS). • A negative impact of ROS should not be significant in swimming pool. - Abstract: The potential risks of nanoparticles (NPs) in sunscreens being released into swimming water were evaluated by a series of laboratory experiments simulating the fate and transport of NPs in outdoor swimming pools. NPs released from sunscreen-applied skin were estimated using pig skins covered with five different commercial sunscreens containing TiO_2, ZnO, or both at various concentrations. Assuming that the swimming water treatment processes consisted of filtration, UV irradiation, heating, and chlorination, possible removal of the released NPs by each process was estimated. Generation of hydrogen peroxide (H_2O_2) by the NPs under sunlight and after UV photochemical treatment were measured, and the H_2O_2 concentration possibly present in the swimming pool was calculated based on some specific scenarios of operating an outdoor swimming pool. It was found that a significant amount of the NPs in sunscreens could be released into the swimming water, and accumulate during circulation through the treatment system. However, the concentration of H_2O_2 possibly present in the swimming pool should be below the level at which an adverse effect to bathers is concerned.

  6. Stimulatory effects of neuronally released norepinephrine on renin release in vitro

    Energy Technology Data Exchange (ETDEWEB)

    Matsumura, Yasuo; Kawazoe, Shinka; Ichihara, Toshio; Shinyama, Hiroshi; Kageyama, Masaaki; Morimoto, Shiro (Osaka Univ. of Pharmaceutical Sciences (Japan))

    1988-10-01

    Extracellular high potassium inhibits renin release in vitro by increasing calcium concentrations in the juxtaglomerular cells. The authors found that the decreased response of renin release from rat kidney cortical slices in high potassium solution changed to a strikingly increased one in the presence of nifedipine at doses over 10{sup {minus}6} M. They then examined the stimulatory effect of extracellular high potassium in the presence of nifedipine on renin release. The enhancement of release was significantly suppressed either by propranolol or by metoprolol but not by prazosin. High potassium plus nifedipine-induced increase in renin release was markedly attenuated by renal denervation. The enhancing effect was not observed when the slices were incubated in calcium-free medium. Divalent cations such as Cd{sup 2+}, Co{sup 2+}, and Mn{sup 2+} blocked this enhancement in a concentration-dependent manner. High potassium elicited an increase in {sup 3}H efflux from the slices preloaded with ({sup 3}H)-norepinephrine. The increasing effect was not influenced by nifedipine but was abolished by the removal of extracellular calcium or by the addition of divalent cations. These observations suggest to us that the high potassium plus nifedipine-induced increase in renin release from the slices is mediated by norepinephrine derived from renal sympathetic nerves and that this neuronally released norepinephrine stimulates renin release via activation of {beta}-adrenoceptors.

  7. An In-Vitro Study on the Release of Fluoride from Two Restorative Materials and Their Rechargeability after Exposure to Daily 1000 ppm Fluoride

    Directory of Open Access Journals (Sweden)

    A. Kowsari

    2005-09-01

    Full Text Available Statement of Problem: Since the fluoride releases from materials with the property of releasing fluoride are decreasing gradually, it seems that probably the material rechargeability is more important than their long-term fluoride release.Purpose: the objective of this study was to asses the fluoride release and rechargeability of 2 types of fluoride releasing restorative materials, a resin modified glass ionomer(Vitremer and a compomer (Compoglass F, after exposure to daily NaF solutionscontaining 1000 ppm F, for 1 minute.Materials and Methods: Twelve discs ( 8 mm ×2 mm of each of the materials were fabricated, and divided into 2 groups (test and control. All discs were stored in 4 mL artificial saliva at 37°C. In group 1 (N=6, the specimens were immersed in artificialsaliva which was changed daily for 25 days. In group 2 (N=6, in addition to receiving the same treatment as group 1, the specimens were immersed in NaF solution (1000ppm F, ph=6.9 for 1 minute before daily saliva change. A potentiometer was used to determine the amount of fluoride released on days 1, 2, 3, 5, 10, 15, 20 and 25, after the daily saliva change, in all study groups. Data were analyzed by the t-student test after confirmation of the equality of variances by Leven’s test.Results: Both materials continued releasing fluoride throughout the whole study period. For each material, the release was highest on day one. During the first 3 days,glass ionomer released significantly higher amounts of fluoride as compared to compomer (p0.05. After exposure to NaF solution, none of the materials showed statistically significant rechargeability (p>0.05 and the amount of fluoride-releasecontinued to drop during the study period in similar patterns for both the test and the control groups.Conclusion: It may be concluded that rechargeability of glass ionomer and compomer,using daily neutral fluoride mouth rinses and toothpastes does not occur in reliable amounts.

  8. Preparation and Evaluation of Oxaliplatin Thermosensitive Liposomes with Rapid Release and High Stability.

    Directory of Open Access Journals (Sweden)

    Chunying Zeng

    Full Text Available Oxaliplatin (OXP was reported to show low anti-tumor activity when used alone and to display side effects; this low activity was attributed to high partitioning to erythrocytes and low accumulation in tumors. Thermosensitive liposomes (TSL were considered able to specifically deliver drugs to heated tumors and to resolve the OXP distribution problem. Regretfully, TSL encapsulating doxorubicin did not demonstrate significant improvement in progression-free survival. Drug release below 41°C and significant leakage were considered major reasons for the failure. The purpose of this study was to acquire OXP TSL with rapid release at the triggered temperature and high stability at body temperature and at storage temperatures. A small quantity of poloxamer 188 was introduced into the TSL formulation to stabilize the encapsulated drug. It was shown that the addition of poloxamer 188 had no influence on the TSL characteristics. More than 90% of OXP was released within 10 min at 42°C, and less than 15% was released within 60 min at temperatures below 39°C. TSL were stable at 37°C for 96 h and at 4°C for 6 months. The anti-tumor activity of TSL at the dose of 2.5 mg/kg was certified to be equal to those of OXP injection and non-thermosensitive liposomes (NTSL at the dose of 5 mg/kg, and significant improvement of tumor inhibition was observed in TSL compared with injection and NTSL at the same dose. It was also shown from the histological transmutation of tumors that TSL had stronger anti-tumor activity. Therefore, it could be concluded that TSL composed of a proper amount of poloxamer had rapid release and high stability, and OXP TSL would be anticipated to exert prominent anti-tumor activity in the clinic.

  9. Riola release report

    Energy Technology Data Exchange (ETDEWEB)

    Woodward, E.C.

    1983-08-04

    Eleven hours after execution of the Riola Event (at 0826 PDT on 25 September 1980) in hole U2eq of the Nevada Test Site (NTS), a release of radioactivity began. When the seepage stopped at about noon the following day, up to some 3200 Ci of activity had been dispersed by light variable winds. On 26 September, examination of the geophone records showed six hours of low-level, but fairly continuous, activity before the release. Electrical measurements indicated that most cables were still intact to a depth below the stemming platform. A survey of the ground zero area showed that the seepage came through cracks between the surface conductor and the pad, through cracks in the pad, and through a crack adjacent to the pad around the mousehole (a small hole adjacent to the emplacement hole). To preclude undue radiation exposure or injury from a surprise subsidence, safety measures were instituted. Tritium seepage was suffucient to postpone site activities until a box and pipeline were emplaced to contain and remove the gas. Radiation release modeling and calculations were generally consistent with observations. Plug-hole interaction calculations showed that the alluvium near the bottom of the plug may have been overstressed and that improvements in the design of the plug-medium interface can be made. Experimental studies verified that the surface appearance of the plug core was caused by erosion, but, assuming a normal strength for the plug material, that erosion alone could not account for the disappearance of such a large portion of the stemming platform. Samples from downhole plug experiments show that the plug may have been considerably weaker than had been indicted by quality assurance (QA) samples. 19 references, 32 figures, 10 tables.

  10. Riola release report

    International Nuclear Information System (INIS)

    Woodward, E.C.

    1983-01-01

    Eleven hours after execution of the Riola Event (at 0826 PDT on 25 September 1980) in hole U2eq of the Nevada Test Site (NTS), a release of radioactivity began. When the seepage stopped at about noon the following day, up to some 3200 Ci of activity had been dispersed by light variable winds. On 26 September, examination of the geophone records showed six hours of low-level, but fairly continuous, activity before the release. Electrical measurements indicated that most cables were still intact to a depth below the stemming platform. A survey of the ground zero area showed that the seepage came through cracks between the surface conductor and the pad, through cracks in the pad, and through a crack adjacent to the pad around the mousehole (a small hole adjacent to the emplacement hole). To preclude undue radiation exposure or injury from a surprise subsidence, safety measures were instituted. Tritium seepage was suffucient to postpone site activities until a box and pipeline were emplaced to contain and remove the gas. Radiation release modeling and calculations were generally consistent with observations. Plug-hole interaction calculations showed that the alluvium near the bottom of the plug may have been overstressed and that improvements in the design of the plug-medium interface can be made. Experimental studies verified that the surface appearance of the plug core was caused by erosion, but, assuming a normal strength for the plug material, that erosion alone could not account for the disappearance of such a large portion of the stemming platform. Samples from downhole plug experiments show that the plug may have been considerably weaker than had been indicted by quality assurance (QA) samples. 19 references, 32 figures, 10 tables

  11. Different amounts of ejaculatory activity, a natural rewarding behavior, induce differential mu and delta opioid receptor internalization in the rat's ventral tegmental area.

    Science.gov (United States)

    Garduño-Gutiérrez, René; León-Olea, Martha; Rodríguez-Manzo, Gabriela

    2013-12-06

    Opioid receptors internalize upon specific agonist stimulation. The in vivo significance of receptor internalization is not well established, partly due to the limited in vivo models used to study this phenomenon. Ejaculation promotes endogenous opioid release which activates opioid receptors at the brain, including the mesolimbic system and medial preoptic area. The objective of the present work was to analyze if there was a correlation between the degree of in vivo mu (MOR) and delta opioid receptor (DOR) internalization in the ventral tegmental area and the execution of different amounts of ejaculatory behavior of male rats. To this aim, we analyzed the brains of rats that ejaculated once or six successive times and of sexually exhausted rats with an established sexual inhibition, using immunofluorescence and confocal microscopy. Results showed that MOR and DOR internalization increased as a consequence of ejaculation. There was a relationship between the amount of sexual activity executed and the degree of internalization for MOR, but not for DOR. MOR internalization was larger in rats that ejaculated repeatedly than in animals ejaculating only once. Significant DOR internalization was found only in animals ejaculating once. Changes in MOR, DOR and beta arrestin2 detection, associated to sexual activity, were also found. It is suggested that copulation to satiety might be useful as a model system to study the biological significance of receptor internalization. © 2013 Published by Elsevier B.V.

  12. Tritium release from neutron irradiated beryllium pebbles

    Energy Technology Data Exchange (ETDEWEB)

    Scaffidi-Argentina, F.; Werle, H. [Forschungszentrum Karlsruhe GmbH Technik und Umwelt (Germany). Inst. fuer Neutronenphysik und Reactortechnik

    1998-01-01

    One of the most important open issues related to beryllium for fusion applications refers to the kinetics of the tritium release as a function of neutron fluence and temperature. The EXOTIC-7 as well as the `Beryllium` experiments carried out in the HFR reactor in Petten are considered as the most detailed and significant tests for investigating the beryllium response under neutron irradiation. This paper reviews the present status of beryllium post-irradiation examinations performed at the Forschungszentrum Karlsruhe with samples from the above mentioned irradiation experiments, trying to elucidate the tritium release controlling processes. In agreement with previous studies it has been found that release starts at about 500-550degC and achieves a maximum at about 700-750degC. The observed release at about 500-550degC is probably due to tritium escaping from chemical traps, while the maximum release at about 700-750degC is due to tritium escaping from physical traps. The consequences of a direct contact between beryllium and ceramics during irradiation, causing tritium implanting in a surface layer of beryllium up to a depth of about 40 mm and leading to an additional inventory which is usually several times larger than the neutron-produced one, are also presented and the effects on the tritium release are discussed. (author)

  13. Mining Significant Semantic Locations from GPS Data

    DEFF Research Database (Denmark)

    Cao, Xin; Cong, Gao; Jensen, Christian Søndergaard

    2010-01-01

    With the increasing deployment and use of GPS-enabled devices, massive amounts of GPS data are becoming available. We propose a general framework for the mining of semantically meaningful, significant locations, e.g., shopping malls and restaurants, from such data. We present techniques capable...... of extracting semantic locations from GPS data. We capture the relationships between locations and between locations and users with a graph. Significance is then assigned to locations using random walks over the graph that propagates significance among the locations. In doing so, mutual reinforcement between...

  14. Mining significant semantic locations from GPS data

    DEFF Research Database (Denmark)

    Cao, Xin; Cong, Gao; Jensen, Christian S.

    2010-01-01

    With the increasing deployment and use of GPS-enabled devices, massive amounts of GPS data are becoming available. We propose a general framework for the mining of semantically meaningful, significant locations, e.g., shopping malls and restaurants, from such data. We present techniques capable...... of extracting semantic locations from GPS data. We capture the relationships between locations and between locations and users with a graph. Significance is then assigned to locations using random walks over the graph that propagates significance among the locations. In doing so, mutual reinforcement between...

  15. Renal epithelial cells can release ATP by vesicular fusion

    Directory of Open Access Journals (Sweden)

    Randi G Bjaelde

    2013-09-01

    Full Text Available Renal epithelial cells have the ability to release nucleotides as paracrine factors. In the intercalated cells of the collecting duct, ATP is released by connexin30 (cx30, which is selectively expressed in this cell type. However, ATP is released by virtually all renal epithelia and the aim of the present study was to identify possible alternative nucleotide release pathways in a renal epithelial cell model. We used MDCK (type1 cells to screen for various potential ATP release pathways. In these cells, inhibition of the vesicular H+-ATPases (bafilomycin reduced both the spontaneous and hypotonically (80%-induced nucleotide release. Interference with vesicular fusion using N-ethylamide markedly reduced the spontaneous nucleotide release, as did interference with trafficking from the endoplasmic reticulum to the Golgi apparatus (brefeldin A1 and vesicular transport (nocodazole. These findings were substantiated using a siRNA directed against SNAP-23, which significantly reduced spontaneous ATP release. Inhibition of pannexin and connexins did not affect the spontaneous ATP release in this cell type, which consists of ∼90% principal cells. TIRF-microscopy of either fluorescently-labeled ATP (MANT-ATP or quinacrine-loaded vesicles, revealed that spontaneous release of single vesicles could be promoted by either hypoosmolality (50% or ionomycin. This vesicular release decreased the overall cellular fluorescence by 5.8% and 7.6% respectively. In summary, this study supports the notion that spontaneous and induced ATP release can occur via exocytosis in renal epithelial cells.

  16. Allegheny County Toxics Release Inventory

    Data.gov (United States)

    Allegheny County / City of Pittsburgh / Western PA Regional Data Center — The Toxics Release Inventory (TRI) data provides information about toxic substances released into the environment or managed through recycling, energy recovery, and...

  17. Environmental risks due to radionuclide releases Environmental Risks Due To Radionuclide Releases From The Oil And Gas Industry

    International Nuclear Information System (INIS)

    Steinhausler, F.

    2005-01-01

    Full text : Exploration and transport in the oil- and gas industry result in the release of elevated levels of natural radioactivity into the environment. This has the following impact: Due to the large volumes of water needed during the extraction of gas and oil the resulting waste water can contain increased concentration of natural radionuclides, such as radium (Ra 226) and its decay products; At the oil/water interface waste water and sludge precipitate and form scalings, containing elevated levels of radium (Ra 226); At oil- and gas extraction sites tanks and equipment can be coated with long-lived radon (Rn 222) decay products; Along oil- and gas pipelines (e.g., at compressor stations) radon (Rn 222) decay products can be deposited internally on metal surfaces, such as valves. Typical U 238-series concentration values in production water range from 8 to 42 kBq/ m3, respectively in scale from 1 to 1 000 kBq/kg. In addition, oil- and gas extraction results in significant releases of natural radionuclides to the atmosphere (Rn 222) and to the water (Th 228, Ra 226, Rn 222, Pb 210, Po 210); for example, about 0.15 GBq/a of Rn 222 are released to the atmosphere per 106 m3 of oil extracted. The disposal of large amounts of contaminated wastes (scales, sludges) represents an environmental problem for the scrap metal industry (recycling of steel pipes containing scales) and the housing industry (use of sludge for landfill below a residential area). Using data from the oil- and gas industry in Latin America, Europe and the Asia-Pacific region, the various exposure pathways are reviewed. Furthermore, the current efforts in defining a suitable regulatory framework are discussed

  18. USING OF THE COVER AMOUNTS METHOD FOR OPTIMIZATION OF INCOME

    Directory of Open Access Journals (Sweden)

    A. V. Volkov

    2007-01-01

    Full Text Available The method of cover amounts (marginal income gives possibility to determine profitableness of each kind of the production and their real contribution into the result of work of enterprise.

  19. Nuclear liability amounts on the rise for nuclear installations

    International Nuclear Information System (INIS)

    Vasquez-Maignan, Ximena; Schwartz, Julia; Kuzeyli, Kaan

    2015-01-01

    The NEA Table on Nuclear Operator Liability Amounts and Financial Security Limits (NEA 'Liability Table'), which covers 71 countries, aims to provide one of the most comprehensive listings of nuclear liability amounts and financial security limits. The current and revised Paris and Brussels Supplementary Conventions ('Paris-Brussels regime'), the original and revised Vienna Conventions ('Vienna regime') and the Convention on Supplementary Compensation for Nuclear Damage, newly entered into force in April 2015, provide for the minimum amounts to be transposed in the national legislation of states parties to the conventions, and have served as guidelines for non-convention states. This article examine in more detail increases in the liability amounts provided for under these conventions, as well as examples of non-convention states (China, India and Korea)

  20. Amount of Future Forest Edge at a 2 Hectare Scale

    Data.gov (United States)

    U.S. Environmental Protection Agency — Forests provide economic and ecological value. High amounts of forest edge indicates a highly fragmented forest, which generally diminishes those economic and...

  1. 41 CFR 105-56.019 - Offset amount.

    Science.gov (United States)

    2010-07-01

    ... Administration 56-SALARY OFFSET FOR INDEBTEDNESS OF FEDERAL EMPLOYEES TO THE UNITED STATES Centralized Salary... referred for offset under this subpart is $100. (b) The amount offset from a salary payment under this... resolved to the satisfaction of GSA. ...

  2. Amount of Forest Edge at a 65 Hectare Scale

    Data.gov (United States)

    U.S. Environmental Protection Agency — Forests provide economic and ecological value. High amounts of forest edge indicates a highly fragmented forest, which generally diminishes those economic and...

  3. Amount of Future Forest Edge at a 65 Hectare scale

    Data.gov (United States)

    U.S. Environmental Protection Agency — Forests provide economic and ecological value. High amounts of forest edge indicates a highly fragmented forest, which generally diminishes those economic and...

  4. Amount of Forest Edge at a 2 Hectare Scale

    Data.gov (United States)

    U.S. Environmental Protection Agency — Forests provide economic and ecological value. High amounts of forest edge indicates a highly fragmented forest, which generally diminishes those economic and...

  5. 24 CFR 17.48 - Computation of amount of award.

    Science.gov (United States)

    2010-04-01

    ... be no allowance for replacement cost or for appreciation in the value of the property. Subject to... repairs does not exceed the amount allowable under paragraph (a)(1) of this section. (b) Depreciation in...

  6. Evaluation of the amount of apically extruded debris during ...

    African Journals Online (AJOL)

    2015-04-06

    Apr 6, 2015 ... Objective: To evaluate the amount of apically extruded debris during retreatment (with or without solvent) of root canals filled by two ... These filling materials can be used with several obturation .... The tip of the master cone.

  7. 24 CFR 206.105 - Amount of MIP.

    Science.gov (United States)

    2010-04-01

    ... DEVELOPMENT MORTGAGE AND LOAN INSURANCE PROGRAMS UNDER NATIONAL HOUSING ACT AND OTHER AUTHORITIES HOME EQUITY CONVERSION MORTGAGE INSURANCE Contract Rights and Obligations Mortgage Insurance Premiums § 206.105 Amount of...

  8. Compressional, mechanical and release properties of a novel gum in paracetamol tablet formulations

    Directory of Open Access Journals (Sweden)

    Adedokun Musiliu O.

    2014-09-01

    Full Text Available The binding properties of Eucalyptus gum obtained from the incised trunk of Eucalyptus tereticornis, were evaluated in paracetamol tablet formulations, in comparison with that of Gelatin B.P. In so doing, the compression properties were analyzed using density measurements and the compression equations of Heckel, Kawakita and Gurham. In our work, the mechanical properties of the tablets were assessed using the crushing strength and friability of the tablets, while the drug release properties of the tablets were assessed using disintegration and dissolution times. The results of the study reveal that tablet formulations incorporating Eucalyptus gum as binder, exhibited faster onset and higher amount of plastic deformation during compression than those containing gelatin. What is more, the Gurnham equation could be used as a substitute for the Kawakita equation in describing the compression properties of pharmaceutical tablets. Furthermore, the crushing strength, disintegration and dissolution times of the tablets increased with binder concentration, while friability values decreased. We noted that no significant differences in properties exist between formulations derived from the two binders (p > 0.05 exist. While tablets incorporating gelatin exhibited higher values for mechanical properties, Eucalyptus gum tablets had better balance between mechanical and release properties - as seen from the CSFR/Dt values. Tablets of good mechanical and release properties were prepared using Eucalyptus gum as a binder, and, therefore, it could serve as an alternative binder in producing tablets with good mechanical strength and fast drug release.

  9. Sugar amount analysis in food from Lithuanian food market

    OpenAIRE

    Gudauskaitė, Milda

    2015-01-01

    When taking too much simple sugar, especially sucrose, harmful health effects occur: more tooth decay occurs, the excess sugar coverts into fat, digestive system gets irritated, increase of weight, possibility in increasing of developing cancer cells, pancreatic and other misbalances in the endocrine organs. Thesis goal: to perform sugar amount analysis in Lithuanian food market Analysis methodology. Assessing the amount of sugar (g/100g) there was analyzed 147 major food la...

  10. Dam pre-release as an important operation strategy in reducing flood impact in Malaysia

    Science.gov (United States)

    Hidayah Ishak, Nurul; Mustafa Hashim, Ahmad

    2018-03-01

    The 2014 flood was reported to be one of the worst natural disaster has ever affected several states in the northern part of Peninsular Malaysia. Overwhelming rainfall was noted as one of the main factors causing such impact, which was claimed to be unprecedented to some extent. The state of Perak, which is blessed with four cascading dams had also experienced flood damage at a scale that was considered the worst in history. The rainfall received had caused the dam to reach danger level that necessitated additional discharge to be released. Safety of the dams was of great importance and such unavoidable additional discharge was allowed to avoid catastrophic failure of the dam structures. This paper discusses the dam pre-release as a significant dam management strategy in reducing flood impact. An important balance between required dam storage to be maintained and the risk element that can be afforded is the crucial factor in such enhanced operation strategy. While further possibility in developing a carefully engineered dam pre-release strategy can be explored for dam operation in Malaysia, this has already been introduced in some developed countries. Australia and South Africa are examples where pre-release has been practiced and proven to reduce flood risk. The concept involves controlling the dam lake level throughout the year, in reference to the rainfall data and the hydrological properties for the catchment area of the dams. Plentiful data analysis need to be done in contemplation of producing the optimal pre-release model. The amount of heavy rainfalls received is beyond human control but the distribution of the discharge from the dams can be further managed with the appropriate pre-release strategy.

  11. The inventory of sources, environmental releases and risk assessment for perfluorooctane sulfonate in China

    International Nuclear Information System (INIS)

    Zhang Lai; Liu Jianguo; Hu Jianxin; Liu Chao; Guo Weiguang; Wang Qiang; Wang Hong

    2012-01-01

    With about 100 t/y of the production volume, perfluorootane sulfonates (PFOS) are mainly used for metal plating, aqueous fire-fighting foams (AFFFs) and sulfluramidin China, and the use amount is about 30–40 t/y, 25–35 t/y and 4–8 t/y respectively. Based on the inventory of PFOS production and uses with geographic distribution educed from statistics, environmental risk assessment of PFOS was taken by using EUSES model, as well as its environmental releases were estimated both in local and regional levels in China. While the environmental release from manufacture is significant in Central China region, metal plating was identified as the major PFOS release source in regional level. The East China region shows the most strong emission strength of PFOS. Though the predicted environmental concentrations (PECs) were not exceed current relevant predicted no effect concentrations (PNECs) of the risk characterization for PFOS, higher PECs was estimated around major PFOS release sources showing undesirable environmental risk at local level. - Highlights: ► Inventory of production and uses of perfluorooctane sulfonate (PFOS) in China with geographical distribution. ► Characteristics of PFOS release sources and distribution consistent with social-economic situation in China. ► Effective model predicted results of PFOS environmental risk assessment in local and regional scales compared with relevant environmental monitoring data. - Inventory of PFOS production and use of with sectoral and regional distribution of China, environmental releases and risk status were indicated both in the local and regional level of the country.

  12. Acetamiprid Accumulates in Different Amounts in Murine Brain Regions

    Directory of Open Access Journals (Sweden)

    Hayato Terayama

    2016-09-01

    Full Text Available Neonicotinoids such as acetamiprid (ACE belong to a new and widely used single class of pesticides. Neonicotinoids mimic the chemical structure of nicotine and share agonist activity with the nicotine acetylcholine receptor (nAchR. Neonicotinoids are widely considered to be safe in humans; however, they have recently been implicated in a number of human health disorders. A wide range of musculoskeletal and neuromuscular disorders associated with high doses of neonicotinoids administered to animals have also been reported. Consequently, we used a mouse model to investigate the response of the central nervous system to ACE treatment. Our results show that exposure to ACE-containing water for three or seven days (decuple and centuple of no observable adverse effect level (NOAEL/day caused a decrease in body weight in 10-week old A/JJmsSlc (A/J mice. However, the treatments did not affect brain histology or expression of CD34. ACE concentrations were significantly higher in the midbrain of ACE-treated mice than that of the normal and vehicle groups. Expression levels of α7, α4, and β2 nAChRs were found to be low in the olfactory bulb and midbrain of normal mice. Furthermore, in the experimental group (centuple ACE-containing water for seven days, β2 nAChR expression decreased in many brain regions. Information regarding the amount of accumulated ACE and expression levels of the acetylcholine receptor in each region of the brain is important for understanding any clinical symptoms that may be associated with ACE exposure.

  13. Polymeric nanoparticles containing diazepam: preparation, optimization, characterization, in-vitro drug release and release kinetic study

    Science.gov (United States)

    Bohrey, Sarvesh; Chourasiya, Vibha; Pandey, Archna

    2016-03-01

    Nanoparticles formulated from biodegradable polymers like poly(lactic-co-glycolic acid) (PLGA) are being extensively investigated as drug delivery systems due to their two important properties such as biocompatibility and controlled drug release characteristics. The aim of this work to formulated diazepam loaded PLGA nanoparticles by using emulsion solvent evaporation technique. Polyvinyl alcohol (PVA) is used as stabilizing agent. Diazepam is a benzodiazepine derivative drug, and widely used as an anticonvulsant in the treatment of various types of epilepsy, insomnia and anxiety. This work investigates the effects of some preparation variables on the size and shape of nanoparticles prepared by emulsion solvent evaporation method. These nanoparticles were characterized by photon correlation spectroscopy (PCS), transmission electron microscopy (TEM). Zeta potential study was also performed to understand the surface charge of nanoparticles. The drug release from drug loaded nanoparticles was studied by dialysis bag method and the in vitro drug release data was also studied by various kinetic models. The results show that sonication time, polymer content, surfactant concentration, ratio of organic to aqueous phase volume, and the amount of drug have an important effect on the size of nanoparticles. Hopefully we produced spherical shape Diazepam loaded PLGA nanoparticles with a size range under 250 nm with zeta potential -23.3 mV. The in vitro drug release analysis shows sustained release of drug from nanoparticles and follow Korsmeyer-Peppas model.

  14. The influences of consumer characteristics on the amount of rice consumption

    Science.gov (United States)

    Supriana, T.; Pane, TC

    2018-02-01

    This study aimed to analyze the characteristics of rice consumers and the influences of consumer characteristics on the amount of rice consumption. The research areas were determined purposively in the sub-districts with the most significant population in Medan City. The analytical methods used were descriptive and multiple linear regression analysis. The results showed that consumers in the study areas have various characteristics, concerning age, income, family size, health, and education. Simultaneously, characteristics of rice consumers have the significant effect on the amount of rice consumed. Partially, age and the number of family members have the significant effect on the amount of rice consumed. The implications of this research are, need different policies toward consumers of rice based on their income strata. Rice policies cannot be generalized.

  15. Modelling rainfall amounts using mixed-gamma model for Kuantan district

    Science.gov (United States)

    Zakaria, Roslinazairimah; Moslim, Nor Hafizah

    2017-05-01

    An efficient design of flood mitigation and construction of crop growth models depend upon good understanding of the rainfall process and characteristics. Gamma distribution is usually used to model nonzero rainfall amounts. In this study, the mixed-gamma model is applied to accommodate both zero and nonzero rainfall amounts. The mixed-gamma model presented is for the independent case. The formulae of mean and variance are derived for the sum of two and three independent mixed-gamma variables, respectively. Firstly, the gamma distribution is used to model the nonzero rainfall amounts and the parameters of the distribution (shape and scale) are estimated using the maximum likelihood estimation method. Then, the mixed-gamma model is defined for both zero and nonzero rainfall amounts simultaneously. The formulae of mean and variance for the sum of two and three independent mixed-gamma variables derived are tested using the monthly rainfall amounts from rainfall stations within Kuantan district in Pahang Malaysia. Based on the Kolmogorov-Smirnov goodness of fit test, the results demonstrate that the descriptive statistics of the observed sum of rainfall amounts is not significantly different at 5% significance level from the generated sum of independent mixed-gamma variables. The methodology and formulae demonstrated can be applied to find the sum of more than three independent mixed-gamma variables.

  16. A fission gas release model

    Energy Technology Data Exchange (ETDEWEB)

    Denis, A; Piotrkowski, R [Argentine Atomic Energy Commission, Buenos Aires (Argentina)

    1997-08-01

    The hypothesis contained in the model developed in this work are as follows. The UO{sub 2} is considered as a collection of spherical grains. Nuclear reactions produce fission gases, mainly Xe and Kr, within the grains. Due to the very low solubility of these gases in UO{sub 2}, intragranular bubbles are formed, of a few nanometers is size. The bubbles are assumed to be immobile and to act as traps which capture gas atoms. Free atoms diffuse towards the grain boundaries, where they give origin to intergranular, lenticular bubbles, of the order of microns. The gas atoms in bubbles, either inter or intragranular, can re-enter the matrix through the mechanism of resolution induced by fission fragment impact. The amount of gas stored in intergranular bubbles grows up to a saturation value. Once saturation is reached, intergranular bubbles inter-connect and the gas in excess is released through different channels to the external surface of the fuel. The resolution of intergranular bubbles particularly affects the region of the grain adjacent to the grain boundary. During grain growth, the grain boundary traps the gas atoms, either free or in intragranular bubbles, contained in the swept volume. The grain boundary is considered as a perfect sink, i.e. the gas concentration is zero at that surface of the grain. Due to the spherical symmetry of the problem, the concentration gradient is null at the centre of the grain. The diffusion equation was solved using the implicit finite difference method. The initial solution was analytically obtained by the Laplace transform. The calculations were performed at different constant temperatures and were compared with experimental results. They show the asymptotic growth of the grain radius as a function of burnup, the gas distribution within the grain at every instant, the growth of the gas content at the grain boundary up to the saturation value and the fraction of gas released by the fuel element referred to the total gas generated

  17. Validation of software releases for CMS

    International Nuclear Information System (INIS)

    Gutsche, Oliver

    2010-01-01

    The CMS software stack currently consists of more than 2 Million lines of code developed by over 250 authors with a new version being released every week. CMS has setup a validation process for quality assurance which enables the developers to compare the performance of a release to previous releases and references. The validation process provides the developers with reconstructed datasets of real data and MC samples. The samples span the whole range of detector effects and important physics signatures to benchmark the performance of the software. They are used to investigate interdependency effects of all CMS software components and to find and fix bugs. The release validation process described here is an integral part of CMS software development and contributes significantly to ensure stable production and analysis. It represents a sizable contribution to the overall MC production of CMS. Its success emphasizes the importance of a streamlined release validation process for projects with a large code basis and significant number of developers and can function as a model for future projects.

  18. Dexamethasone-induced haptoglobin release by calf liver parenchymal cells.

    Science.gov (United States)

    Higuchi, H; Katoh, N; Miyamoto, T; Uchida, E; Yuasa, A; Takahashi, K

    1994-08-01

    Parenchymal cells were isolated from the liver of male calves, and monolayer cultures formed were treated with glucocorticoids to examine whether haptoglobin, appearance of which is associated with hepatic lipidosis (fatty liver) in cattle, is induced by steroid hormones. Without addition of dexamethasone, only trace amounts of haptoglobin were detected in culture medium. With addition of dexamethasone (10(-12) to 10(-4) M), considerable amounts of haptoglobin were released into the medium. Maximal release was observed at concentrations of 10(-8) to 10(-6) M dexamethasone. Haptoglobin release was similarly induced by cortisol, although the effect was less potent than that of dexamethasone. Actinomycin D (a known protein synthesis inhibitor) dose-dependently reduced amounts of haptoglobin released in response to 10(-8) M dexamethasone. Dexamethasone also induced annexin I, which is known to be synthesized in response to glucocorticoids. Dexamethasone treatment resulted in reduced protein kinase C activity in the cell cytosol, which has been shown to be an early event in dexamethasone-treated cells. Other than glucocorticoids, estradiol induced haptoglobin release, whereas progesterone was less effective. The association of haptoglobin with hepatic lipidosis can be reasonably explained by the fact that haptoglobin production by the liver is induced by glucocorticoids and estradiol, and these steroid hormones are triggers for development of hepatic lipidosis in cattle.

  19. The market for equity release products: Lessons from the ...

    African Journals Online (AJOL)

    Home Equity Release Products (ERPs) are innovative fi nancial instruments that enable elderly, retired people to use their unencumbered houses as a source of income/funding while they continue to reside in them, thereby seeking to address the constraints of the life cycle hypothesis. The loan and outstanding amounts ...

  20. Differential antibiotic-induced endotoxin release in severe melioidosis

    NARCIS (Netherlands)

    Simpson, A. J.; Opal, S. M.; Angus, B. J.; Prins, J. M.; Palardy, J. E.; Parejo, N. A.; Chaowagul, W.; White, N. J.

    2000-01-01

    Severe melioidosis is a life-threatening, systemic bacterial infection caused by Burkholderia pseudomallei. A prospective, randomized treatment trial was conducted in northeast Thailand to compare ceftazidime (a penicillin-binding protein [PBP]-3-specific agent that causes release of large amounts

  1. Influence of bracket-slot design on the forces released by superelastic nickel-titanium alignment wires in different deflection configurations.

    Science.gov (United States)

    Nucera, Riccardo; Gatto, Elda; Borsellino, Chiara; Aceto, Pasquale; Fabiano, Francesca; Matarese, Giovanni; Perillo, Letizia; Cordasco, Giancarlo

    2014-05-01

    To evaluate how different bracket-slot design characteristics affect the forces released by superelastic nickel-titanium (NiTi) alignment wires at different amounts of wire deflection. A three-bracket bending and a classic-three point bending testing apparatus were used to investigate the load-deflection properties of one superelastic 0.014-inch NiTi alignment wire in different experimental conditions. The selected NiTi archwire was tested in association with three bracket systems: (1) conventional twin brackets with a 0.018-inch slot, (2) a self-ligating bracket with a 0.018-inch slot, and (3) a self-ligating bracket with a 0.022-inch slot. Wire specimens were deflected at 2 mm and 4 mm. Use of a 0.018-inch slot bracket system, in comparison with use of a 0.022-inch system, increases the force exerted by the superelastic NiTi wires at a 2-mm deflection. Use of a self-ligating bracket system increases the force released by NiTi wires in comparison with the conventional ligated bracket system. NiTi wires deflected to a different maximum deflection (2 mm and 4 mm) release different forces at the same unloading data point (1.5 mm). Bracket design, type of experimental test, and amount of wire deflection significantly affected the amount of forces released by superelastic NiTi wires (Pwire's load during alignment.

  2. Building Adjustable Pre-storm Reservoir Flood-control Release Rules

    Science.gov (United States)

    Yang, Shun-Nien; Chang, Li-Chiu; Chang, Fi-John; Hsieh, Cheng-Daw

    2017-04-01

    Typhoons hit Taiwan several times every year, which could cause serious flood disasters. Because mountainous terrains and steep landforms can rapidly accelerate the speed of flood flow during typhoon events, rivers cannot be a stable source of water supply. Reservoirs become the most effective floodwater storage facilities for alleviating flood damages in Taiwan. The pre-storm flood-control release can significantly increase reservoir storage capacity available to store floodwaters for reducing downstream flood damage, while the uncertainties of total forecasted rainfalls are very high in different stages of an oncoming typhoon, which may cause the risk of water shortage in the future. This study proposes adjustable pre-storm reservoir flood-control release rules in three designed operating stages with various hydrological conditions in the Feitsui Reservoir, a pivot reservoir for water supply to Taipei metropolitan in Taiwan, not only to reduce the risk of reservoir flood control and downstream flooding but also to consider water supply. The three operating stages before an oncoming typhoon are defined upon the timings when: (1) typhoon news is issued (3-7days before typhoon hit); (2) the sea warning is issued (2-4 days before typhoon hit); and (3) the land warning is issued (1-2 days before typhoon hit). We simulate 95 historical typhoon events with 3000 initial water levels and build some pre-storm flood-control release rules to adjust the amount of pre-release based on the total forecasted rainfalls at different operating stages. A great number of simulations (68.4 millions) are conducted to extract their major consequences and then build the adjustable pre-storm reservoir flood-control release rules. Accordingly, given a total forecasted rainfall and a water level, reservoir decision makers can easily identify the corresponding rule to tell the amount of pre-release in any stage. The results show that the proposed adjustable pre-release rules can effectively

  3. Cobalt release from inexpensive jewellery

    DEFF Research Database (Denmark)

    Thyssen, Jacob Pontoppidan; Jellesen, Morten Stendahl; Menné, Torkil

    2010-01-01

    . Conclusions: This study showed that only a minority of inexpensive jewellery purchased in Denmark released cobalt when analysed with the cobalt spot test. As fashion trends fluctuate and we found cobalt release from dark appearing jewellery, cobalt release from consumer items should be monitored in the future......Objectives: The aim was to study 354 consumer items using the cobalt spot test. Cobalt release was assessed to obtain a risk estimate of cobalt allergy and dermatitis in consumers who would wear the jewellery. Methods: The cobalt spot test was used to assess cobalt release from all items...

  4. Mechanical properties and modeling of drug release from chlorhexidine-containing etch-and-rinse adhesives.

    Science.gov (United States)

    Stanislawczuk, Rodrigo; Reis, Alessandra; Malaquias, Pamela; Pereira, Fabiane; Farago, Paulo Vitor; Meier, Marcia Margarete; Loguercio, Alessandro D

    2014-04-01

    To evaluate the effects of chlorhexidine (CHX) addition in different concentrations into simplified etch-and-rinse adhesives on the ultimate tensile strength (UTS), water sorption (WS), solubility (SO) and the rate of CHX release over time. We added CHX diacetate to Ambar [AM] (FGM) and XP Bond [XP] (Dentsply) in concentrations of 0, 0.01, 0.05, 0.1 and 0.2 wt%. For UTS (n=10 for each group), adhesive specimens were constructed in an hourglass shape metallic matrix with cross-sectional area of 0.8 mm(2). Half of specimens were tested after 24 h and the other half after 28 days of water storage in tension of 0.5 mm/min. For WS and SO (n=10 for each group), adhesive discs (5.8 mm×1.0 mm) were prepared into a mold. After desiccation, we weighed and stored the cured adhesive specimens in distilled water for evaluation of the WS, SO and the cumulative release of CHX over a 28-day period. For CHX release (n=10 for each group), spectrophotometric measurements of storage solution were performed to examine the release kinetics of CHX. We subjected data from each test to ANOVA and Tukey' test (α=0.05). XP Bond adhesive showed significantly more WS and SO and lower UTS than Ambar. In general, the addition of CHX did not alter WS, SO and UTS of the adhesives. XP showed a higher CHX release than AM (p<0.05) in all concentrations and the final amount of CHX release was directly proportional to the initial CHX concentration added to the adhesives. After 28 days of water storage, approximately 20% of CHX was released from XP and 8.0-12.0% from AM. Addition of CHX to commercial adhesive is a feasible method to provide a controlled release of CHX over time without jeopardizing WS, SO and UTS of the adhesives. Manufacturers should consider adding CHX to commercial adhesives to provide a controlled release of CHX over time. Copyright © 2014 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

  5. Correlation between image quality of CT scan and amount of intravenous contrast media

    International Nuclear Information System (INIS)

    Yoon, Dae Young; Choi, Dae Seob; Kim, Seung Hyup; Han, Joon Koo; Choi, Byung Ihn; Im, Jung Gi; Han, Moon Hee; Chang, Kee Hyun; Kim, Jong Hyo; Han, Man Chung

    1993-01-01

    A blind, comparative clinical study was performed prospectively to examine the correlation between image quality of CT scan in terms of contrast enhancement effect and amount of intravenous contrast media. A total of 357 patients were randomized into two groups. Ionic high-osmolality contrast media (68% meglumine ioglicate) was administered intravenously as 100 ml bolus in one group and as 50 ml bolus in the other group. Statistically significant differences of image quality were found in CT scans of the brain, head and neck, chest and abdomen (p 0.05). We suggest that amount of contrast media may be reduced in pelvis CT without significant degradation of image quality

  6. Manufacturing Amorphous Solid Dispersions with a Tailored Amount of Crystallized API for Biopharmaceutical Testing.

    Science.gov (United States)

    Theil, Frank; Milsmann, Johanna; Anantharaman, Sankaran; van Lishaut, Holger

    2018-05-07

    The preparation of an amorphous solid dispersion (ASD) by dissolving a poorly water-soluble active pharmaceutical ingredient (API) in a polymer matrix can improve the bioavailability by orders of magnitude. Crystallization of the API in the ASD, though, is an inherent threat for bioavailability. Commonly, the impact of crystalline API on the drug release of the dosage form is studied with samples containing spiked crystallinity. These spiked samples possess implicit differences compared to native crystalline samples, regarding size and spatial distribution of the crystals as well as their molecular environment. In this study, we demonstrate that it is possible to grow defined amounts of crystalline API in solid dosage forms, which enables us to study the biopharmaceutical impact of actual crystallization. For this purpose, we studied the crystal growth in fenofibrate tablets over time under an elevated moisture using transmission Raman spectroscopy (TRS). As a nondestructive method to assess API crystallinity in ASD formulations, TRS enables the monitoring of crystal growth in individual dosage forms. Once the kinetic trace of the crystal growth for a certain environmental condition is determined, this method can be used to produce samples with defined amounts of crystallized API. To investigate the biopharmaceutical impact of crystallized API, non-QC dissolution methods were used, designed to identify differences between the various amounts of crystalline materials present. The drug release in the samples manufactured in this fashion was compared to that of samples with spiked crystallinity. In this study, we present for the first time a method for targeted crystallization of amorphous tablets to simulate crystallized ASDs. This methodology is a valuable tool to generate model systems for biopharmaceutical studies on the impact of crystallinity on the bioavailability.

  7. Investigating the in vitro drug release kinetics from controlled release diclofenac potassium-ethocel matrix tablets and the influence of co-excipients on drug release patterns.

    Science.gov (United States)

    Shah, Shefaat Ullah; Shah, Kifayat Ullah; Rehman, Asimur; Khan, Gul Majid

    2011-04-01

    The objective of the study was to formulate and evaluate controlled release polymeric tablets of Diclofenac Potassium for the release rate, release patterns and the mechanism involved in the release process of the drug. Formulations with different types and grades of Ethyl Cellulose Ether derivatives in several drug-to-polymer ratios (D:P) were compressed into tablets using the direct compression method. In vitro drug release studies were performed in phosphate buffer (pH 7.4) as dissolution medium by using USP Method-1 (Rotating Basket Method). Similarity factor f2 and dissimilarity factor f1 were applied for checking the similarities and dissimilarities of the release profiles of different formulations. For the determination of the release mechanism and drug release kinetics various mathematical/kinetic models were employed. It was found that all of the Ethocel polymers could significantly slow down the drug release rate with Ethocel FP polymers being the most efficient, especially at D:P ratios of 10:03 which lead towards the achievement of zero or near zero order release kinetics.

  8. Preparation and Characterization of Sustained Release Matrix ...

    African Journals Online (AJOL)

    tablet formulations showed a percent drug release ranging from 92.54 ± 1.02 to 98.56 ± 1.26 % at the end of 12 h. Using the spinal injury rat model, ... very common and significant problem. Nonsteroidal anti-inflammatory drugs (NSAIDs) ... animal studies, its mechanism of action involves depressing polysynaptic reflexes ...

  9. Significance of blood examination in radiation workers

    International Nuclear Information System (INIS)

    Mori, Hirofumi; Nakamura, Shinobu; Ando, Atsushi; Kojima, Kazuhiko; Kikuta, Yoko.

    1978-01-01

    Blood examination made for the past 3 years revealed that the influences of chronic exposure of extremely small amounts of radiation (an average of 5 mrem/day) on peripheral blood are not detected. However, the blood examination, which is prescribed at least twice a year by law, is for determining whether or not the results of blood examination are within a normal range. Therefore, even though influences of a large amount of radiation are detected, it has little significance as a monitoring of chronic exposure of extremely small amounts of radiation. If the blood examination is used as a monitoring method for detecting exposure, it is important to compare the results with the previous ones in the same individuals. It is also necessary to increase the number of examinations and to study the blood more in detail. However, before that, the standard of the evaluation should be more defined because of its obscurity. The present blood examination is useful in managing the health generally. However, it is not good as a monitoring for chronic exposure of the extremely small amounts of radiation. Therefore, a routine biological method to be able to monitor radiation more precisely, is required. (Namekawa, K.)

  10. Ultrasound stimulated release of gallic acid from chitin hydrogel matrix

    International Nuclear Information System (INIS)

    Jiang, Huixin; Kobayashi, Takaomi

    2017-01-01

    Ultrasound (US) stimulated drug release was examined in this study using a chitin hydrogel matrix loaded with gallic acid (GA), a drug used for wound healing and anticancer. Using phase inversion, GA-chitin hydrogels were prepared from chitin-dimethylacetamide (DMAc)/lithium chloride (LiCl) solution in the presence of GA, with 24 h exposure of the solution to water vapor. The GA release from the GA-chitin hydrogel was examined under different US powers of 0–30 W at 43 kHz. The effects of GA loading amounts in the hydrogels (0.54, 0.43, and 0.25 mg/cm 3 ) and chitin concentrations (0.1, 0.5, and 1 wt%) on the release behaviors were recorded under 43 kHz US exposure at 30 W. Results show that US accelerated the release efficiencies for all samples. Furthermore, the release efficiency increased concomitantly with increasing US power, GA loading amount, and decrease of the chitin concentration. The highest release rate of 0.74 μg/mL·min was obtained from 0.54 mg/cm 3 of GA-loaded hydrogel fabricated from a 0.1 wt% chitin mixture solution under 43 kHz US exposure at 30 W: nine times higher than that of the sample without US exposure. The hydrogel viscoelasticity demonstrated that the US irradiation rigidified the material. FT-IR showed that US can break the hydrogen bonds in the GA-chitin hydrogels. - Highlights: • Ultrasound (US) stimulated Gallic acid (GA) release from chitin hydrogel was studied. • The release efficiency of GA from chitin hydrogel increased nine times when irradiated by 43 kHz US compared with the sample without US. • Generalized 2D correlation and deconvolution study of FT-IR showed that US could promote the GA release by breaking hydrogen bonds.

  11. Ultrasound stimulated release of gallic acid from chitin hydrogel matrix

    Energy Technology Data Exchange (ETDEWEB)

    Jiang, Huixin; Kobayashi, Takaomi, E-mail: takaomi@nagaokaut.ac.jp

    2017-06-01

    Ultrasound (US) stimulated drug release was examined in this study using a chitin hydrogel matrix loaded with gallic acid (GA), a drug used for wound healing and anticancer. Using phase inversion, GA-chitin hydrogels were prepared from chitin-dimethylacetamide (DMAc)/lithium chloride (LiCl) solution in the presence of GA, with 24 h exposure of the solution to water vapor. The GA release from the GA-chitin hydrogel was examined under different US powers of 0–30 W at 43 kHz. The effects of GA loading amounts in the hydrogels (0.54, 0.43, and 0.25 mg/cm{sup 3}) and chitin concentrations (0.1, 0.5, and 1 wt%) on the release behaviors were recorded under 43 kHz US exposure at 30 W. Results show that US accelerated the release efficiencies for all samples. Furthermore, the release efficiency increased concomitantly with increasing US power, GA loading amount, and decrease of the chitin concentration. The highest release rate of 0.74 μg/mL·min was obtained from 0.54 mg/cm{sup 3} of GA-loaded hydrogel fabricated from a 0.1 wt% chitin mixture solution under 43 kHz US exposure at 30 W: nine times higher than that of the sample without US exposure. The hydrogel viscoelasticity demonstrated that the US irradiation rigidified the material. FT-IR showed that US can break the hydrogen bonds in the GA-chitin hydrogels. - Highlights: • Ultrasound (US) stimulated Gallic acid (GA) release from chitin hydrogel was studied. • The release efficiency of GA from chitin hydrogel increased nine times when irradiated by 43 kHz US compared with the sample without US. • Generalized 2D correlation and deconvolution study of FT-IR showed that US could promote the GA release by breaking hydrogen bonds.

  12. Computational modeling and analysis of iron release from macrophages.

    Directory of Open Access Journals (Sweden)

    Alka A Potdar

    2014-07-01

    Full Text Available A major process of iron homeostasis in whole-body iron metabolism is the release of iron from the macrophages of the reticuloendothelial system. Macrophages recognize and phagocytose senescent or damaged erythrocytes. Then, they process the heme iron, which is returned to the circulation for reutilization by red blood cell precursors during erythropoiesis. The amount of iron released, compared to the amount shunted for storage as ferritin, is greater during iron deficiency. A currently accepted model of iron release assumes a passive-gradient with free diffusion of intracellular labile iron (Fe2+ through ferroportin (FPN, the transporter on the plasma membrane. Outside the cell, a multi-copper ferroxidase, ceruloplasmin (Cp, oxidizes ferrous to ferric ion. Apo-transferrin (Tf, the primary carrier of soluble iron in the plasma, binds ferric ion to form mono-ferric and di-ferric transferrin. According to the passive-gradient model, the removal of ferrous ion from the site of release sustains the gradient that maintains the iron release. Subcellular localization of FPN, however, indicates that the role of FPN may be more complex. By experiments and mathematical modeling, we have investigated the detailed mechanism of iron release from macrophages focusing on the roles of the Cp, FPN and apo-Tf. The passive-gradient model is quantitatively analyzed using a mathematical model for the first time. A comparison of experimental data with model simulations shows that the passive-gradient model cannot explain macrophage iron release. However, a facilitated-transport model associated with FPN can explain the iron release mechanism. According to the facilitated-transport model, intracellular FPN carries labile iron to the macrophage membrane. Extracellular Cp accelerates the oxidation of ferrous ion bound to FPN. Apo-Tf in the extracellular environment binds to the oxidized ferrous ion, completing the release process. Facilitated-transport model can

  13. Consumption of energy and release of entropy into the biosphere

    International Nuclear Information System (INIS)

    Deutscher, G.

    2014-01-01

    The short-term threat on humanity is not the shortage of energy but rather the contamination of the environment. The concept of entropy is useful to assess the impact of humane activities on the environment. During most of earth history the increase of entropy was more than compensated by the energy brought by the sun. Today the intensive use of fossil fuels has reversed the trend: the biosphere entropy increases as CO 2 piles up in the atmosphere. The release of entropy is linked to the amount of energy we consume and to the efficiency of the process we use to produce it. Nuclear power plants release entropy as low-temperature heat but this amount of entropy is far less than the entropy released by fossil-fuel power plants under the form of CO 2 . (A.C.)

  14. Nuclear trafficking latest statistics released

    International Nuclear Information System (INIS)

    2005-01-01

    Full text: Countries reported 121 incidents to the IAEA in 2004 of illicit trafficking and other unauthorized activities involving nuclear and other radioactive materials, newly released statistics from the Agency's Illicit Trafficking Database (ITDB) show. The ITDB report also shows that one incident was reported since 2003 that involved fissile material - highly enriched uranium (HEU) or plutonium - that is needed to make a nuclear weapon. It occurred in June 2003 when an individual was arrested in possession of 170 grams of HEU, attempting to illegally transport it across the border. During the two-year period 2003-2004, the number of incidents reported by States substantially increased compared with previous years. 'Improved reporting may in part account for it,' the report said. 'The majority of the incidents reported in 2003-2004 showed no evidence of criminal activity.' The Past Twelve Years: 1993 - 2004 Nuclear Weapons Grade Material. Since the database started in 1993, there have been eighteen confirmed incidents involving trafficking in HEU and plutonium. A few of these incidents involved seizures of kilogram quantities of weapons-usable nuclear material but most involved very small quantities. In some of the cases the seized material was allegedly a sample of larger quantities available for illegal sale or at risk of theft. More than two dozens incidents involved trace amounts of plutonium sources. Table can be viewed: Incidents involving HEU and Pu confirmed to the ITDB (1993-2004). Nuclear Materials. In the past twelve years, 220 incidents involved nuclear materials. The majority of confirmed cases with nuclear materials involved low-grade nuclear materials, mostly in the form of reactor fuel pellets, and natural uranium, depleted uranium and thorium. While the quantities of these materials have been rather small to be significant for nuclear proliferation or use in a terrorist nuclear explosive device, these cases are indicative of gaps in the control

  15. How restrained eaters perceive the amount they eat.

    Science.gov (United States)

    Jansen, A

    1996-09-01

    The cognitive model of binge eating states that it is the awareness of a broken diet that disinhibits the restrained eater. It is, according to that model, the perception of having overeaten that triggers disinhibited eating. However, although the perception of the amount eaten plays a central role in cognitive restraint theory, it has never directly been tested how restrained subjects perceive the amount of food they eat. In the present studies, participants were given ad libitum access to large amounts of palatable food and both their perception of the amount eaten and their estimated caloric intake were compared with the amount they actually ate. The restrained participants in these studies ate more than the unrestrained participants. In the first and second studies, the restrained participants consumed 571 and 372 'forbidden' calories respectively, without having the feeling that they had eaten very much, let alone too much. Moreover in both studies, the restrained eaters underestimated their caloric intake, whereas unrestrained eaters estimated their caloric intake quite well. The potential implications of the present findings for the cognitive restraint model are discussed.

  16. Amounts of mercury in soil of some golf course sites

    Energy Technology Data Exchange (ETDEWEB)

    MacLean, A J; Stone, B; Cordukes, W E

    1973-01-01

    Mercurial compounds are widely used for controlling diseases of turfgrass of golf courses, but the fungicides are usually confined to the greens. Composite soil samples were obtained from three golf courses in the Ottawa and Ontario region of Canada. Samples from the turf and surface layer of soil were analyzed and high amounts of mercury were found. The soil of No.I course was a sand; No.II was a sandy loam in the surface and a loam below; and No. III was a loam in the surface layer and a clay loam below. The pH of the surface layer was 6.4 in No. I, 7.5 in No. II, and 6.0 in No. III. The amounts of Hg in the turf were high near the green but they decreased with distance. Fairway III contained the highest amounts of Hg and there was evidence of it leaching to a depth of 90 cm at the edge of the green. The particularly high amounts of Hg in no III were in accord with the liberal use of mercurial fungicides on this course in the period 1912-64. The leaching of Hg depends on amounts of organic matter and the clay in the soil.

  17. [Characteristics of dissolved organic carbon release under inundation from typical grass plants in the water-level fluctuation zone of the Three Gorges Reservoir area].

    Science.gov (United States)

    Tan, Qiu-Xia; Zhu, Boi; Hua, Ke-Ke

    2013-08-01

    The water-level fluctuation zone of the Three Gorges Reservoir (TGR) exposes in spring and summer, then, green plants especially herbaceous plants grow vigorously. In the late of September, water-level fluctuation zone of TGR goes to inundation. Meanwhile, annually accumulated biomass of plant will be submerged for decaying, resulting in organism decomposition and release a large amount of dissolved organic carbon (DOC). This may lead to negative impacts on water environment of TGR. The typical herbaceous plants from water-level fluctuation zone were collected and inundated in the laboratory for dynamic measurements of DOC concentration of overlying water. According to the determination, the DOC release rates and fluxes have been calculated. Results showed that the release process of DOC variation fitted in a parabolic curve. The peak DOC concentrations emerge averagely in the 15th day of inundation, indicating that DOC released quickly with organism decay of herbaceous plant. The release process of DOC could be described by the logarithm equation. There are significant differences between the concentration of DOC (the maximum DOC concentration is 486.88 mg x L(-1) +/- 35.97 mg x L(-1) for Centaurea picris, the minimum is 4.18 mg x L(-1) +/- 1.07 mg x L(-1) for Echinochloacrus galli) and the release amount of DOC (the maximum is 50.54 mg x g(-1) for Centaurea picris, the minimum is 6.51 mg x g(-1) for Polygonum hydropiper) due to different characteristics of plants, especially, the values of C/N of herbaceous plants. The cumulative DOC release quantities during the whole inundation period were significantly correlated with plants' C/N values in linear equations.

  18. Ingenol mebutate in low amounts for the treatment of actinic keratosis in Korean patients

    Directory of Open Access Journals (Sweden)

    Joe HJ

    2017-03-01

    Full Text Available Hyun Jae Joe, Byung Ho Oh Department of Dermatology, Keimyung University, College of Medicine, Daegu, Republic of Korea Background: Ingenol mebutate (IM, a novel agent for field therapy of actinic keratosis (AK, has a drawback of inducing local skin reactions (LSRs, which may cause discomfort in patients. To reduce the LSRs, we tried the application of IM in low amounts.Objective: The purpose of this study was to review Korean patients with AK being treated with IM and evaluate the LSRs and therapeutic outcomes of low amounts of IM.Methods: We retrospectively reviewed 47 patients with AK on the face. A total of 20 and 27 patients were treated by applying recommended amount of 18.8 mg/cm2 and the lower amount of 10 mg/cm2, respectively.Results: The mean composite LSR score for the low amount group (LAG; 12.18±3.29 was significantly lower than that for the recommended amount group (RAG; 15.45±2.70 (P<0.01, independent sample t-test. The 2-month clearance rate calculated by the number of AKs before and after treatment in each patient was significantly higher for RAG (88.16%, compared with 75.56% for LAG (P<0.001.Conclusion: Low amount of IM for the treatment of facial AK significantly reduced LSRs in Korean patients. Minimizing LSRs may allow for a secondary targeting treatment of IM for the residual lesions, depending on initial treatment outcomes. Keywords: actinic keratosis, field therapy, ingenol mebutate 

  19. Size-separated particle fractions of stainless steel welding fume particles - A multi-analytical characterization focusing on surface oxide speciation and release of hexavalent chromium.

    Science.gov (United States)

    Mei, N; Belleville, L; Cha, Y; Olofsson, U; Odnevall Wallinder, I; Persson, K-A; Hedberg, Y S

    2018-01-15

    Welding fume of stainless steels is potentially health hazardous. The aim of this study was to investigate the manganese (Mn) and chromium (Cr) speciation of welding fume particles and their extent of metal release relevant for an inhalation scenario, as a function of particle size, welding method (manual metal arc welding, metal arc welding using an active shielding gas), different electrodes (solid wires and flux-cored wires) and shielding gases, and base alloy (austenitic AISI 304L and duplex stainless steel LDX2101). Metal release investigations were performed in phosphate buffered saline (PBS), pH 7.3, 37°, 24h. The particles were characterized by means of microscopic, spectroscopic, and electroanalytical methods. Cr was predominantly released from particles of the welding fume when exposed in PBS [3-96% of the total amount of Cr, of which up to 70% as Cr(VI)], followed by Mn, nickel, and iron. Duplex stainless steel welded with a flux-cored wire generated a welding fume that released most Cr(VI). Nano-sized particles released a significantly higher amount of nickel compared with micron-sized particle fractions. The welding fume did not contain any solitary known chromate compounds, but multi-elemental highly oxidized oxide(s) (iron, Cr, and Mn, possibly bismuth and silicon). Copyright © 2017 The Authors. Published by Elsevier B.V. All rights reserved.

  20. The release of silver nanoparticles from commercial toothbrushes

    International Nuclear Information System (INIS)

    Mackevica, Aiga; Olsson, Mikael Emil; Hansen, Steffen Foss

    2017-01-01

    Highlights: • Ag and Ag nanoparticle release was measured from two types of toothbrushes. • Maximum release for entire intended product use period was 10 ng Ag per toothbrush. • Released Ag nanoparticles had median sizes from 42 to 47 nm. • Up to 2.8% of total Ag released was detected in nanoparticulate form. - Abstract: The use of silver nanoparticles (NPs) in commercial products has become increasingly common in the past decade, mostly due to their antimicrobial properties. Using Ag NP-containing articles may lead to particle release, which raises concern of human and environmental safety. The published literature addressing particle release is scarce, especially when it comes to quantifying exposure to NPs specifically. In this study, we have experimentally investigated the release of total Ag and Ag NP from commercially available toothbrushes i.e. biodegradable toothbrushes for adults and toothbrushes for children. Toothbrushes were immersed and abraded in tap water for 24 h corresponding to more than the whole intended usage time of a toothbrush. The total amount of released Ag was quantified by inductively coupled plasma—mass spectrometry (ICP-MS) analysis, and the Ag NPs were characterized by single particle ICP-MS and transmission electron microscopy (TEM). The median size of the released Ag NPs ranged from 42 to 47 nm, and the maximum total Ag release was 10.2 ng per toothbrush. The adult toothbrushes were generally releasing more total Ag and NPs than children toothbrushes. In conclusion, our results indicate that the use of Ag NP-impregnated toothbrushes can cause consumer as well as environmental exposure to Ag NPs.

  1. The release of silver nanoparticles from commercial toothbrushes

    Energy Technology Data Exchange (ETDEWEB)

    Mackevica, Aiga, E-mail: aima@env.dtu.dk; Olsson, Mikael Emil; Hansen, Steffen Foss

    2017-01-15

    Highlights: • Ag and Ag nanoparticle release was measured from two types of toothbrushes. • Maximum release for entire intended product use period was 10 ng Ag per toothbrush. • Released Ag nanoparticles had median sizes from 42 to 47 nm. • Up to 2.8% of total Ag released was detected in nanoparticulate form. - Abstract: The use of silver nanoparticles (NPs) in commercial products has become increasingly common in the past decade, mostly due to their antimicrobial properties. Using Ag NP-containing articles may lead to particle release, which raises concern of human and environmental safety. The published literature addressing particle release is scarce, especially when it comes to quantifying exposure to NPs specifically. In this study, we have experimentally investigated the release of total Ag and Ag NP from commercially available toothbrushes i.e. biodegradable toothbrushes for adults and toothbrushes for children. Toothbrushes were immersed and abraded in tap water for 24 h corresponding to more than the whole intended usage time of a toothbrush. The total amount of released Ag was quantified by inductively coupled plasma—mass spectrometry (ICP-MS) analysis, and the Ag NPs were characterized by single particle ICP-MS and transmission electron microscopy (TEM). The median size of the released Ag NPs ranged from 42 to 47 nm, and the maximum total Ag release was 10.2 ng per toothbrush. The adult toothbrushes were generally releasing more total Ag and NPs than children toothbrushes. In conclusion, our results indicate that the use of Ag NP-impregnated toothbrushes can cause consumer as well as environmental exposure to Ag NPs.

  2. In vitro atrazine-exposure inhibits human natural killer cell lytic granule release

    International Nuclear Information System (INIS)

    Rowe, Alexander M.; Brundage, Kathleen M.; Barnett, John B.

    2007-01-01

    The herbicide atrazine is a known immunotoxicant and an inhibitor of human natural killer (NK) cell lytic function. The precise changes in NK cell lytic function following atrazine exposure have not been fully elucidated. The current study identifies the point at which atrazine exerts its affect on the stepwise process of human NK cell-mediated lyses of the K562 target cell line. Using intracellular staining of human peripheral blood lymphocytes, it was determined that a 24-h in vitro exposure to atrazine did not decrease the level of NK cell lytic proteins granzyme A, granzyme B or perforin. Thus, it was hypothesized that atrazine exposure was inhibiting the ability of the NK cells to bind to the target cell and subsequently inhibit the release of lytic protein from the NK cell. To test this hypothesis, flow cytometry and fluorescent microscopy were employed to analyze NK cell-target cell co-cultures following atrazine exposure. These assays demonstrated no significant decrease in the level of target cell binding. However, the levels of NK intracellular lytic protein retained and the amount of lytic protein released were assessed following a 4-h incubation with K562 target cells. The relative level of intracellular lytic protein was 25-50% higher, and the amount of lytic protein released was 55-65% less in atrazine-treated cells than vehicle-treated cells following incubation with the target cells. These results indicate that ATR exposure inhibits the ability of NK cells to lyse target cells by blocking lytic granule release without affecting the ability of the NK cell to form stable conjugates with target cells

  3. Quality evaluation of extemporaneous delayed-release liquid formulations of lansoprazole.

    Science.gov (United States)

    Melkoumov, Alexandre; Soukrati, Amina; Elkin, Igor; Forest, Jean-Marc; Hildgen, Patrice; Leclair, Grégoire

    2011-11-01

    The quality attributes of extemporaneous delayed-release liquid formulations of lansoprazole for oral administration were evaluated. A novel liquid formulation (3 mg/mL) of Prevacid FasTab in an Ora-Blend vehicle was prepared and compared with the Prevacid FasTab 30 mg and Prevacid-sodium bicarbonate 1 M formulation (3 mg/mL). The latter formulation was combined with hydrochloric acid 0.1 N, and the remaining lansoprazole content was assayed by high-performance liquid chromatography (HPLC). A batch of delayed-release liquid formulation was prepared to evaluate content uniformity. For content assay, three samples were prepared for each evaluated condition and each sample was analyzed in triplicate by HPLC. The lansoprazole in the sodium bicarbonate formulation was extensively degraded by quantities of hydrochloric acid 0.1 N in excess of 100 mL. Storage time and temperature had a significant effect on lansoprazole stability in the Ora-Blend formulation. The drug remained stable for seven days when the formulation was stored at 4.5-5.5 °C, but storage at 21-22 °C or the reduction of pH with citric acid accelerated lansoprazole degradation. The amount of lansoprazole released from the Ora-Blend formulation during the buffer stage of the dissolution test decreased with increases in formulation storage time, in formulation storage temperature, and in the amount of lansoprazole released and degraded during the acid stage of the test. An extemporaneous formulation consisting of lansoprazole microgranules in Ora-Blend maintained acceptable quality attributes when stored for three days at 4.5-5.5 °C.

  4. Single cell amperometry reveals curcuminoids modulate the release of neurotransmitters during exocytosis from PC12 cells

    Science.gov (United States)

    Li, Xianchan; Mohammadi, Amir Saeid; Ewing, Andrew G.

    2016-01-01

    We used single cell amperometry to examine whether curcumin and bisdemethoxycurcumin (BDMC), substances that are suggested to affect learning and memory, can modulate monoamine release from PC12 cells. Our results indicate both curcumin and BDMC need long-term treatment (72 h in this study) to influence exocytosis effectively. By analyzing the parameters calculated from single exocytosis events, it can be concluded that curcumin and BDMC affect exocytosis through different mechanisms. Curcumin accelerates the event dynamics with no significant change of the monoamine amount released from single exocytotic events, whereas BDMC attenuates the amount from single exocytotic event with no significant change of the event dynamics. This comparison of the effect of curcumin and BDMC on exocytosis at the single cell level brings insight into their different mechanisms, which might lead to different biological actions. The effect of curcumin and BDMC on the opening and closing of the exocytotic fusion pore were also investigated. These results might be helpful for understanding the improvement of learning and memory and the anti-depression properties of curcuminoids. PMID:28579928

  5. Increasing the amount of payment to research subjects

    Science.gov (United States)

    Resnick, DB

    2014-01-01

    This article discusses some ethical issues that can arise when researchers decide to increase the amount of payment offered to research subjects to boost enrollment. Would increasing the amount of payment be unfair to subjects who have already consented to participate in the study? This article considers how five different models of payment—the free market model, the wage payment model, the reimbursement model, the appreciation model, and the fair benefits model—would approach this issue. The article also considers several practical problems related to changing the amount of payment, including determining whether there is enough money in the budget to offer additional payments to subjects who have already enrolled, ascertaining how difficult it will be to re-contact subjects, and developing a plan of action for responding to subjects who find out they are receiving less money and demand an explanation. PMID:18757614

  6. Release of powdered material from waste packages

    International Nuclear Information System (INIS)

    Berg, H.P.; Gruendler, D.; Peiffer, F.; Seehars, H.D.

    1990-01-01

    Possible incidents in the operational phase of the planned German repository KONRAD for radioactive waste with negligible heat production were investigated to assess the radiological consequences. For these investigations release fractions of the radioactive materials are required. This paper deals with the determination of the release of powdered material from waste packages under mechanical stress. These determinations were based on experiments. The experimental procedure and the process parameters chosen in accordance with the conditions in the planned repository will be described. The significance of the experimental results is discussed with respect to incidents in the planned repository. 8 figs., 3 tabs

  7. Application of a Biodegradable Polyesteramide Derived from L-Alanine as Novel Excipient for Controlled Release Matrix Tablets.

    Science.gov (United States)

    Bonillo Martínez, Ana Dora; Galán, Inés Carmen Rodríguez; Bellver, María Victoria Margarit

    2017-11-01

    This pre-formulation study assays the capacity of the polyesteramide PADAS, poly (L-alanine-dodecanediol-L-alanine-sebacic), as an insoluble tablet excipient matrix for prolonged drug release. The flow properties of PADAS were suitable for tableting, and the compressibility of tablets containing exclusively PADAS was evaluated by ESEM observation of the microstructure. The tablets were resistant to crushing and non-friable and they did not undergo disintegration (typical features of an inert matrix). Tablets containing 33.33% sodium diclofenac (DF), ketoprofen (K) or dexketoprofen trometamol (DK-T) as a model drug, in addition with 66.67% of polymer, were formulated, and the absence of interactions between the components was confirmed by differential scanning calorimetry. Dissolution tests showed that PADAS retained DF and K and prolonged drug release, following a Higuchi kinetic. The tablets containing DK-T did not retain the drug sufficiently for prolonged release to be established. Tablets containing DK-T and 66.67, 83.33 or 91.67% PADAS, compressed at 44.48 or 88.96 kN, were elaborated to determine the influence of the polymer amount and of the compression force on DK-T release. Both parameters significantly delayed drug release, except when the proportion of polymer was 91.67%.

  8. 5-Fluorouracil Encapsulated Chitosan Nanoparticles for pH-Stimulated Drug Delivery: Evaluation of Controlled Release Kinetics

    Directory of Open Access Journals (Sweden)

    R. Seda Tığlı Aydın

    2012-01-01

    Full Text Available Nanoparticles consisting of human therapeutic drugs are suggested as a promising strategy for targeted and localized drug delivery to tumor cells. In this study, 5-fluorouracil (5-FU encapsulated chitosan nanoparticles were prepared in order to investigate potentials of localized drug delivery for tumor environment due to pH sensitivity of chitosan nanoparticles. Optimization of chitosan and 5-FU encapsulated nanoparticles production revealed 148.8±1.1 nm and 243.1±17.9 nm particle size diameters with narrow size distributions, which are confirmed by scanning electron microscope (SEM images. The challenge was to investigate drug delivery of 5-FU encapsulated chitosan nanoparticles due to varied pH changes. To achieve this objective, pH sensitivity of prepared chitosan nanoparticle was evaluated and results showed a significant swelling response for pH 5 with particle diameter of ∼450 nm. In vitro release studies indicated a controlled and sustained release of 5-FU from chitosan nanoparticles with the release amounts of 29.1–60.8% due to varied pH environments after 408 h of the incubation period. pH sensitivity is confirmed by mathematical modeling of release kinetics since chitosan nanoparticles showed stimuli-induced release. Results suggested that 5-FU encapsulated chitosan nanoparticles can be launched as pH-responsive smart drug delivery agents for possible applications of cancer treatments.

  9. Unusual amount of (-)-mesquitol from the heartwood of Prosopis juliflora.

    Science.gov (United States)

    Sirmah, Peter; Dumarçay, Stéphane; Masson, Eric; Gérardin, Philippe

    2009-01-01

    A large amount of flavonoid has been extracted and isolated from the heartwood of Prosopis juliflora, an exogenous wood species of Kenya. Structural and physicochemical elucidation based on FTIR, (1)H and (13)C NMR, GC-MS and HPLC analysis clearly demonstrated the presence of (-)-mesquitol as the sole compound without any noticeable impurities. The product was able to slow down oxidation of methyl linoleate induced by AIBN. The important amount and high purity of (-)-mesquitol present in the acetonic extract of P. juliflora could therefore be of valuable interest as a potential source of antioxidants from a renewable origin.

  10. Role of fission gas release in reactor licensing

    International Nuclear Information System (INIS)

    1975-11-01

    The release of fission gases from oxide pellets to the fuel rod internal voidage (gap) is reviewed with regard to the required safety analysis in reactor licensing. Significant analyzed effects are described, prominent gas release models are reviewed, and various methods used in the licensing process are summarized. The report thus serves as a guide to a large body of literature including company reports and government documents. A discussion of the state of the art of gas release analysis is presented

  11. Design of a controlled release system of OP-1 and TGF-β1 based in microparticles of sodium alginate and release characterization by HPLC-UV.

    Science.gov (United States)

    Oliva-Rodríguez, Ricardo; Pérez-Urizar, José; Dibildox-Alvarado, Estela; Martínez-Saldaña, María Consolación; Avelar-González, Francisco Javier; Flores-Reyes, Héctor; Pozos-Guillén, Amaury de Jesús; Guerrero-Barrera, Alma Lilián

    2011-12-01

    A new system for sustained release of growth factors, such as osteogenic protein 1 (OP-1) and transforming growth factor β1 (TGF-β1), intended to repair and promote dental tissue regeneration in rats was designed and characterized in this work. The release system was made with microparticles of sodium alginate, produced by ionic gelling dripping technique. The release profiles of OP-1 and TGF-β1 from biopolymer matrix were determined by high-performance liquid chromatography (HPLC), and with this purpose, an HPLC-UV method was developed. About 80% of each growth factor was released in the first 24 h, reaching almost 100% in 168 h. The system was tested during the tissue repair in rat molars in comparison with calcium hydroxide and both growth factors not encapsulated. The dentin sialoprotein (DSP) was used as a repair marker. It was detected by immunohistochemistry, after 14- and 28-d post-treatment. X (2) test (p ≤ 0.001) and Fisher exact test (p ≤ 0.05) were applied for assessment of the amount of immunostaining. The treatment with encapsulated OP-1 showed an increased DSP immunostaining after 14 d and did not find any significant difference with the immunostaining observed for calcium hydroxide treatment. Treatment with TGF-β1 did not show significant difference with calcium hydroxide. Treatment with both factors OP-1 and TGF-β1 showed higher DSP immunostaining in comparison with calcium hydroxide treatment. In conclusion, the combination of both growth factors encapsulated showed more DSP immunostaining in comparison with each one separated, either encapsulated or not.

  12. Reference amounts utilised in front of package nutrition labelling; impact on product healthfulness evaluations.

    Science.gov (United States)

    Raats, M M; Hieke, S; Jola, C; Hodgkins, C; Kennedy, J; Wills, J

    2015-05-01

    The research question addressed in this paper is how different reference amounts utilised in front of package nutrition labelling influence evaluation of product healthfulness. A total of 13,117 participants from six European countries (Germany, UK, Spain, France, Poland and Sweden) were recruited via online panels. A mixed between/within-subject factorial design was employed with food (biscuits, sandwiches, yogurts), healthfulness and presence of Guideline Daily Amounts as within-subjects factors and reference amount ('per 100 g', 'typical portion', 'half portion') and country as between-subjects factors. Overall, people correctly ranked foods according to their objective healthfulness as defined by risk nutrients alone, and could distinguish between more and less healthful variants of foods. General healthfulness associations with the three product categories do not appear to have had a strong influence on product ratings. This study shows that where the reference amount of 'per 100 g' is very different from the 'typical' portion size, as was the case for biscuits, products with a 'per 100 g' label are rated significantly less healthful than the 'typical' or 'half typical' portions. The results indicate that across the three food categories, consumers do factor the reference amount, that is, the quantity of food for which the nutritional information is being presented, into their judgements of healthfulness. Therefore, appropriate reference amounts are also of importance for the effective presentation of nutritional information.

  13. Influence of decrease of the amount of starting salary of radiological technologists

    International Nuclear Information System (INIS)

    Shibuya, Koichi; Kato, Hirokazu

    2010-01-01

    This paper analyzes differences and changes within and between the occupation of nurses, radiological technologists, and medical technologists concerning starting salary from April 2005 to March 2009. This paper also investigates the percentage of difference in the amount of starting salary of nurses, radiological technologists, and medical technologists according to their educational attainments. The research-target used was the full-time-job-opening data provided to Okayama University within the given period of time, which specifies the amount of starting salary. The result shows that one's educational background has a crucial influence on the amount of one's starting salary. In fact, the percentage of the amount of starting salary base on one's educational attainment all increased in nurses, radiological technologists, and medical technologists from April 2007 to March 2009. However, this percentage for radiological technologists remains only 50% of increase, which was less significant than other two professional occupations. Moreover, the result indicates a crucial change in the amount of basic starting salary: while the amount of basic starting salary of nurses in 2008 has increased since 2005, that of radiological technologists has dropped remarkably. If this situation is not improved in the near future, the health-service sector may experience a decrease in the number of skilled practitioners which, in turn, will result in a decline in quality of medical care. (author)

  14. Gravitational vacuum and energy release in microworld

    International Nuclear Information System (INIS)

    Mel'nikov, V.N.; Nikolaev, Yu.M.; Stanyukovich, K.P.

    1981-01-01

    It is shown that gravitati.onal interaction can be connected with the processes of energy release in microworld. Suggested is a planckeon model within the frames of which gradual production of the observed substance of the Universe during the whole evolution is explained. Burst processes in nuclei of the Galaxy are explained. It is concluded that the theory of gravitational vacuum creates preconditions for developing the general theory of the field explaining the basic peculiarities of the micro- and macroworld, reveals significant applications in the physics of elementary particles and atomic nucleus. The process of 235 U fission is considered for testing the hypothesis that the coefficient of energy release depends on the nature of the reaction in different processes of energy release in the micro- and macroworld [ru

  15. The influence of DOM and microbial processes on arsenic release from karst during ASR operations in the Floridan Aquifer

    Science.gov (United States)

    Jin, J.; Zimmerman, A. R.

    2011-12-01

    The mobilization of subsurface As poses a serious threat to human health, particularly in a region such as Florida where population is heavily dependent on highly porous karstic aquifers for drinking water. Injection water used in aquifer storage and recovery (ASR) or aquifer recharge (AR) operations is commonly high in dissolved organic matter (DOM) and OM can also be present in the subsurface carbonate rock. Using batch incubation experiments, this study examined the role of core preservation methods, as well as the influence of labile and more refractory DOM on the mobilization of As from carbonate rock. Incubation experiments used sealed reaction vessels with preserved and homogenized core materials collected via coring the Suwannee Formation in southwest Florida and treatment additions consisting of 1) source water (SW) enriched in sterilized soil DOM, 2) SW enriched in soil DOM and microbes, and 3) SW enriched in sodium acetate. During an initial equilibration phase in native groundwater (NGW) with low dissolved oxygen (DO; Phase 1), we found the greatest As release of the whole incubation. In the beginning of Phase 2 (N2 headspace) in which NGW was replaced with treatment solutions, there was little As release except in the vessel with Na-acetate added, which also had the lowest ORP. At the start of Phase 3, when incubations were exposed to air, most vessels saw more ion (including As) release into solution. Vessel with Na-acetate had less As release in Phase 3 than in Phase 2. During all experimental phases, treatments of DOM or microbe additions had no apparent effect on the amount of As release. The core materials was found contain significant amount of indigenous DOM (about 8 g OC/kg core) which was released during the incubation so DOC concentrations displayed no clear pattern among different treatments. At least three abiotic As mobilization mechanisms may play a role in As released during different stages of the experiment. Desorption of As from iron

  16. 29 CFR 4.141 - General criteria for measuring amount.

    Science.gov (United States)

    2010-07-01

    ... Government for such work under his contract or may even agree to pay the Government in return for the right... formal advertising, in arriving at the aggregate amount involved, there must be included all property and... single advertisement for bids if the procurement were being effected by formal advertising. Therefore, if...

  17. 42 CFR 402.105 - Amount of penalty.

    Science.gov (United States)

    2010-10-01

    ... insurance benefit plans (§ 402.1(c)(21)). (b) $1,000. CMS or OIG may impose a penalty of not more than $1... 42 Public Health 2 2010-10-01 2010-10-01 false Amount of penalty. 402.105 Section 402.105 Public Health CENTERS FOR MEDICARE & MEDICAID SERVICES, DEPARTMENT OF HEALTH AND HUMAN SERVICES GENERAL...

  18. 20 CFR 404.338 - Widow's and widower's benefits amounts.

    Science.gov (United States)

    2010-04-01

    ... benefit may change as explained in § 404.304. (c) Your monthly benefit will be reduced if the insured person chooses to receive old-age benefits before reaching full retirement age. If so, your benefit will... 20 Employees' Benefits 2 2010-04-01 2010-04-01 false Widow's and widower's benefits amounts. 404...

  19. 26 CFR 1.617-2 - Limitation on amount deductible.

    Science.gov (United States)

    2010-04-01

    ... 1.617-2 Internal Revenue INTERNAL REVENUE SERVICE, DEPARTMENT OF THE TREASURY (CONTINUED) INCOME TAX (CONTINUED) INCOME TAXES (CONTINUED) Natural Resources § 1.617-2 Limitation on amount deductible. (a... 1967, 1968, 1969, and 1970 A had exploration costs of $80,000 all with respect to coal deposits located...

  20. 26 CFR 1.615-4 - Limitation of amount deductible.

    Science.gov (United States)

    2010-04-01

    ... 1.615-4 Internal Revenue INTERNAL REVENUE SERVICE, DEPARTMENT OF THE TREASURY (CONTINUED) INCOME TAX (CONTINUED) INCOME TAXES (CONTINUED) Natural Resources § 1.615-4 Limitation of amount deductible. (a) Taxable... lease with respect to certain coal lands. A has deducted exploration expenditures under section 615 for...

  1. 42 CFR 493.649 - Methodology for determining fee amount.

    Science.gov (United States)

    2010-10-01

    ... fringe benefit costs to support the required number of State inspectors, management and direct support... full time equivalent employee. Included in this cost are salary and fringe benefit costs, necessary... 42 Public Health 5 2010-10-01 2010-10-01 false Methodology for determining fee amount. 493.649...

  2. 42 CFR 422.382 - Minimum net worth amount.

    Science.gov (United States)

    2010-10-01

    ... that CMS considers appropriate to reduce, control or eliminate start-up administrative costs. (b) After... section. (c) Calculation of the minimum net worth amount—(1) Cash requirement. (i) At the time of application, the organization must maintain at least $750,000 of the minimum net worth amount in cash or cash...

  3. 7 CFR 3550.63 - Maximum loan amount.

    Science.gov (United States)

    2010-01-01

    ... self-help housing will be calculated by adding the total of the market value of the lot (including... amount. Total secured indebtedness must not exceed the area loan limit or market value limitations... appraisal, tax monitoring fee, and the charge to establish an escrow account for taxes and insurance will...

  4. 41 CFR 105-56.029 - Offset amount.

    Science.gov (United States)

    2010-07-01

    ... Administration 56-SALARY OFFSET FOR INDEBTEDNESS OF FEDERAL EMPLOYEES TO THE UNITED STATES Centralized Salary... salary offset under this subpart is $100. (b) The amount offset from a salary payment under this subpart... otherwise resolved to the satisfaction of the creditor agency. ...

  5. 20 CFR 615.6 - Extended Benefits; weekly amount.

    Science.gov (United States)

    2010-04-01

    ... 20 Employees' Benefits 3 2010-04-01 2010-04-01 false Extended Benefits; weekly amount. 615.6 Section 615.6 Employees' Benefits EMPLOYMENT AND TRAINING ADMINISTRATION, DEPARTMENT OF LABOR EXTENDED... compensation payable during such benefit year. (2) If the method in paragraph (a)(1)(iii) of this section is...

  6. 46 CFR 308.300 - Insured amount-application.

    Science.gov (United States)

    2010-10-01

    ... Shipping MARITIME ADMINISTRATION, DEPARTMENT OF TRANSPORTATION EMERGENCY OPERATIONS WAR RISK INSURANCE Second Seamen's War Risk Insurance § 308.300 Insured amount—application. An applicant for Second Seamen's war risk insurance shall not state the amount of insurance desired, which shall be as provided in...

  7. 13 CFR 143.52 - Collection of amounts due.

    Science.gov (United States)

    2010-01-01

    ... 13 Business Credit and Assistance 1 2010-01-01 2010-01-01 false Collection of amounts due. 143.52 Section 143.52 Business Credit and Assistance SMALL BUSINESS ADMINISTRATION UNIFORM ADMINISTRATIVE... Government. If not paid within a reasonable period after demand, the Federal agency may reduce the debt by...

  8. 34 CFR 682.506 - Limitations on maximum loan amounts.

    Science.gov (United States)

    2010-07-01

    ... loan is intended less— (i) The student's estimated financial assistance; and (ii) The student's.... (b) The Secretary does not guarantee a Federal Consolidation loan in an amount greater than that required to discharge loans eligible for consolidation under § 682.100(a)(4). (Authority: 20 U.S.C. 1075...

  9. 7 CFR 3565.204 - Maximum loan amount.

    Science.gov (United States)

    2010-01-01

    ... project. The lender shall recommend to the Agency an adjustment in the loan amount if appropriate as a result of this review. (2) Where the project financing combines a guaranteed loan with Low-Income Housing Tax Credits or other Federal assistance, the project must conform to the policies regarding necessary...

  10. 9 CFR 89.1 - Amount of feed.

    Science.gov (United States)

    2010-01-01

    ... 9 Animals and Animal Products 1 2010-01-01 2010-01-01 false Amount of feed. 89.1 Section 89.1 Animals and Animal Products ANIMAL AND PLANT HEALTH INSPECTION SERVICE, DEPARTMENT OF AGRICULTURE INTERSTATE TRANSPORTATION OF ANIMALS (INCLUDING POULTRY) AND ANIMAL PRODUCTS STATEMENT OF POLICY UNDER THE...

  11. 29 CFR 530.303 - Considerations in determining amounts.

    Science.gov (United States)

    2010-07-01

    ... 29 Labor 3 2010-07-01 2010-07-01 false Considerations in determining amounts. 530.303 Section 530... REGULATIONS EMPLOYMENT OF HOMEWORKERS IN CERTAIN INDUSTRIES Civil Money Penalties § 530.303 Considerations in... representations; and (5) Exercise of due care. (b) An employer's financial inability to meet obligations under the...

  12. 76 FR 71554 - Civil Penalties; Notice of Adjusted Maximum Amounts

    Science.gov (United States)

    2011-11-18

    ... Substances Act (FHSA), and the Flammable Fabrics Act (FFA). The Improvement Act added civil penalty authority... penalty amounts authorized under the Consumer Product Safety Act, the Federal Hazardous Substances Act, and the Flammable Fabrics Act. On August 14, 2009, the Consumer Product Safety Improvement Act of 2008...

  13. 78 FR 4057 - Inflation Adjustment of Civil Money Penalty Amounts

    Science.gov (United States)

    2013-01-18

    ...] RIN 2501-AD59 Inflation Adjustment of Civil Money Penalty Amounts AGENCY: Office of the Secretary, HUD. ACTION: Final rule. SUMMARY: This final rule amends HUD's civil money penalty and civil penalty... outdated cross-reference in its civil money penalty regulations. DATES: Effective Date: February 19, 2013...

  14. AMOUNT TO EXPROPRIATION? AN ANALYSIS OF THE Agri SA

    African Journals Online (AJOL)

    Examiner

    then make an order for the payment against the defendant to the state of any amount .... The second point of criticism is found in a decision of the Australian High Court, .... system when it comes to distinguishing between deprivation and ...

  15. 47 CFR 54.403 - Lifeline support amount.

    Science.gov (United States)

    2010-10-01

    ... local exchange carrier serving the area in which the qualifying low-income consumer receives service, as... a qualifying low-income consumer's intrastate rate, if the carrier has received the non-federal... SERVICE Universal Service Support for Low-Income Consumers § 54.403 Lifeline support amount. (a) The...

  16. 26 CFR 1.1441-2 - Amounts subject to withholding.

    Science.gov (United States)

    2010-04-01

    ..., it shall apply only to obligations issued after December 31, 2000. (4) Securities lending... issue discount) described in section 871(i)(2)(A) or 881(d)); (3) Amounts described in § 1.1441-1(b)(4)(iv) (dealing with interest or original issue discount on certain short-term obligations described in...

  17. Effects of hyperthyroidism and hypothyroidism on rat growth hormone release induced by thyrotropin-releasing hormone.

    Science.gov (United States)

    Chihara, K; Kato, Y; Ohgo, S; Iwasaki, Y; Maeda, K

    1976-06-01

    The effect of synthetic thyrotropin-releasing hormone (TRH) on the release of growth hormone (GH) and thyroid-stimulating hormone (TSH) was investigated in euthyroid, hypothyroid, and hyperthyroid rats under urethane anesthesia. In euthyroid control rats, intravenous injection of TRH (200 ng/100 g BW) resulted in a significant increase in both plasma GH and TSH. In rats made hypothyroid by treatment with propylthiouracil or by thyroidectomy, basal GH and TSH levels were significantly elevated with exaggerated responses to TRH. In contrast, plasma GH and TSH responses to TRH were both significantly inhibited in rats made hyperthyroid by L-thyroxine (T4) treatment. These results suggest that altered thyroid status influences GH release as well as TSH secretion induced by TRH in rats.

  18. Release of nitrogen precursors from coal and biomass residues in a bubbling fluidized bed

    Energy Technology Data Exchange (ETDEWEB)

    P. Abelha; I. Gulyurtlu; I. Cabrita [Instituto Nacional de Engenharia, Lisbon (Portugal)

    2008-01-15

    This work was undertaken with the aim of quantifying the relative amounts of NH{sub 3} and HCN released from different residues during their devolatilization under fluidized bed conditions. The results were compared with data collected for bituminous coals of different origin. The relation between amounts of HCN and NH{sub 3} released and the levels of NOX and N{sub 2}O formed during cocombustion was also addressed. The partitioning of nitrogen between volatiles and char was also quantified. The pyrolysis studies were undertaken in a small fluidized bed reactor of 80 mm of ID and 500 mm high using an inert atmosphere (N{sub 2}). The HCN and NH{sub 3} were quantified by bubbling the pyrolysis gases in absorbing solutions which were subsequently analyzed with selective electrodes. The combustion studies were carried out on a pilot installation. The fluidized bed combustor is square in cross section with each side being 300 mm long. There is secondary air supply to the freeboard at different heights to deal with high volatile fuels as almost all waste materials are. The temperatures in the bed and in the freeboard and that of the flue gases leaving the reactor were continuously monitored. The results obtained suggest that, while coal releases nitrogen mostly as HCN, residues like RDF and sewage sludge give out fuel-N in greater quantities as NH{sub 3}. Residues at fluidized bed combustion (FBC) temperatures release more than 80% of the fuel-N with the volatiles. The NH{sub 3} evolved during pyrolysis acted as a reducing agent on NOX emissions. The presence of calcium significantly reduces the emission of N{sub 2}O probably by interfering with HCN chemistry. With high amounts of residues in the fuel mixture, the relative importance of char on the nitrogen chemistry substantially decreases. By using cocombustion, it is possible to reduce fuel-N conversion to NOX and N{sub 2}O, by tuning the amounts of coal and residue in the mixture. 29 refs., 18 figs., 3 tabs.

  19. Released radioactivity reducing facility

    International Nuclear Information System (INIS)

    Tanaka, Takeaki.

    1992-01-01

    Upon occurrence of a reactor accident, penetration portions of a reactor container, as a main leakage source from a reactor container, are surrounded by a plurality of gas-tight chambers, the outside of which is surrounded by highly gas-tightly buildings. Branched pipelines of an emergency gas processing system are introduced to each of the gas-tight chambers and they are joined and in communication with an emergency gas processing device. With such a constitution, radioactive materials are prevented from leaking directly from the buildings. Further, pipeline openings of the emergency gas processing facility are disposed in the plurality highly gas-tight penetration chambers. If the radioactive materials are leaked from the reactor to elevate the pressure in the penetration chambers, the radioactive materials are introduced to a filter device in the emergency gas processing facility by way of the branched pipelines, filtered and then released to the atmosphere. Accordingly, the reliability and safety of the system can be improved. (T.M.)

  20. Containment and release management

    International Nuclear Information System (INIS)

    Lehner, J.R.; Pratt, W.T.

    1988-01-01

    Reducing the risk from potentially severe accidents by appropriate accident management strategies is receiving increased attention from the international reactor safety community. Considerable uncertainty still surrounds some of the physical phenomena likely to occur during a severe accident. The USNRC, in developing its research plan for accident management, wants to ensure that both the developers and implementers of accident management strategies are aware of the uncertainty associated with the plant operators' ability to correctly diagnose an accident, as well as the uncertainties associated with various preventive and mitigative strategies. The use of a particular accident management strategy can have both positive and negative effects on the status of a plant and these effects must be carefully weighed before a particular course of action is chosen and implemented. By using examples of severe accident scenarios, initial insights are presented here regarding the indications plant operators may have to alert them to particular accident states. Insights are also offered on the various management actions operators and plant technical staff might pursue for particular accident situations and the pros and cons associated with such actions. The examples given are taken for the most part from the containment and release phase of accident management, since this is the current focus of the effort in the accident management area at Brookhaven National Laboratory. 2 refs

  1. Released radioactivity reducing device

    International Nuclear Information System (INIS)

    Miyamoto, Yumi.

    1995-01-01

    A water scrubber is disposed in a scrubber tank and a stainless steel fiber filter is disposed above the water scrubber. The upper end of the scrubber tank is connected by way of a second bent tube to a capturing vessel incorporating a moisture removing layer and an activated carbon filter. The exit of the capturing vessel is connected to a stack. Upon occurrence of an accident of a BWR-type power plant, gases containing radioactive materials released from a reactor container are discharged into the water scrubber from a first bent tube through a venturi tube nozzle, and water soluble and aerosol-like radioactive materials are captured in the water. Aerosol and splashes of water droplets which can not be captured thoroughly by the water scrubber are captured by the stainless steel fiber filter. Gases passing through the scrubber tank are introduced to a capturing vessel through a second bent tube, and organic iodine is captured by the activated carbon filter. (I.N.)

  2. Equilibrium and kinetic models for colloid release under transient solution chemistry conditions

    Science.gov (United States)

    We present continuum models to describe colloid release in the subsurface during transient physicochemical conditions. Our modeling approach relates the amount of colloid release to changes in the fraction of the solid surface area that contributes to retention. Equilibrium, kinetic, equilibrium and...

  3. Radionuclide releases to the atmosphere from Hanford Operations, 1944--1972. Hanford Environmental Dose Reconstruction Project

    Energy Technology Data Exchange (ETDEWEB)

    Heeb, C.M.

    1994-05-01

    The purpose of the Hanford Environmental Dose Reconstruction Project is to estimate the radiation dose that individuals could have received as a result of radionuclide emissions since 1944 from the Hanford Site. The first step in determining dose is to estimate the amount and timing of radionuclide releases to air and water. This report provides the air release information.

  4. Investigation of chloride-release of nuclear grade resin in PWR primary system coolant

    International Nuclear Information System (INIS)

    Cao Xiaoning; Li Yunde; Li Jinghong; Lin Fangliang

    1997-01-01

    A new preparation technique is developed for making the low-chloride nuclear-grade resin by commercial resin. The chloride remained in nuclear grade resin may release to PWR primary coolant. The amount of released chloride is depended on the concentration of boron, lithium, other anion impurities, and remained chloride concentration in resin

  5. An advanced model for spreading and evaporation of accidentally released hazardous liquids on land

    NARCIS (Netherlands)

    Trijssenaar-Buhre, I.J.M.; Sterkenburg, R.P.; Wijnant-Timmerman, S.I.

    2009-01-01

    Pool evaporation modelling is an important element in consequence assessment of accidentally released hazardous liquids. The evaporation rate determines the amount of toxic or flammable gas released into the atmosphere and is an important factor for the size of a pool fire. In this paper a

  6. An advanced model for spreading and evaporation of accidentally released hazardous liquids on land

    NARCIS (Netherlands)

    Trijssenaar-Buhre, I.J.M.; Wijnant-Timmerman, S.L.

    2008-01-01

    Pool evaporation modelling is an important element in consequence assessment of accidentally released hazardous liquids. The evaporation rate determines the amount of toxic or flammable gas released into the atmosphere and is an important factor for the size of a pool fire. In this paper a

  7. Underground water stress release models

    Science.gov (United States)

    Li, Yong; Dang, Shenjun; Lü, Shaochuan

    2011-08-01

    The accumulation of tectonic stress may cause earthquakes at some epochs. However, in most cases, it leads to crustal deformations. Underground water level is a sensitive indication of the crustal deformations. We incorporate the information of the underground water level into the stress release models (SRM), and obtain the underground water stress release model (USRM). We apply USRM to the earthquakes occurred at Tangshan region. The analysis shows that the underground water stress release model outperforms both Poisson model and stress release model. Monte Carlo simulation shows that the simulated seismicity by USRM is very close to the real seismicity.

  8. Flash release an alternative for releasing complex MEMS devices

    NARCIS (Netherlands)

    Deladi, S.; Krijnen, Gijsbertus J.M.; Elwenspoek, Michael Curt

    2004-01-01

    A novel time-saving and cost-effective release technique has been developed and is described. The physical nature of the process is explained in combination with experimental observations. The results of the flash release process are compared with those of freeze-drying and supercritical CO2

  9. Methodology of external exposure calculation for reuse of conditional released materials from decommissioning - 59138

    International Nuclear Information System (INIS)

    Ondra, Frantisek; Vasko, Marek; Necas, Vladimir

    2012-01-01

    before expedition or temporary storage before next manufacturing activity was found as a critical activity from external exposure point of view. Significant increase of worker exposure is caused by storage of huge amount of radioactive rails in piles. Therefore it is recommended to distribute storage rails into several individual separate storage places. The optimised radionuclide concentrations in conditional released material for external exposure will be compared with radionuclide concentrations for internal exposures calculated by means of GoldSim software tool (another part of the CONRELMAT project). Based on this comparison, more conservative radionuclide concentrations will be selected. (authors)

  10. Stimuli-Responsive Materials for Controlled Release Applications

    KAUST Repository

    Li, Song

    2015-04-01

    The controlled release of therapeutics has been one of the major challenges for scientists and engineers during the past three decades. To address this outstanding problem, the design and fabrication of stimuli-responsive materials are pursued to guarantee the controlled release of cargo at a specific time and with an accurate amount. Upon applying different stimuli such as light, magnetic field, heat, pH change, enzymes or redox, functional materials change their physicochemical properties through physical transformation or chemical reactions, allowing the release of payload agents on demand. This dissertation studied three stimuli-responsive membrane systems for controlled release from films of macro sizes to microcapsules of nano sizes. The first membrane system is a polymeric composite film which can decrease and sustain diffusion upon light irradiation. The photo-response of membranes is based on the photoreaction of cinnamic derivatives. The second one is composite membrane which can improve diffusion upon heating. The thermo-response of membranes comes from the volume phase transition ability of hydrogels. The third one is microcapsule which can release encapsulated agents upon light irradiation. The photo-response of capsules results from the photoreaction of nitrobenzyl derivatives. The study on these membrane systems reveals that stimuli-responsive release can be achieved by utilizing different functional materials on either macro or micro level. Based on the abundant family of smart materials, designing and fabricating stimuli-responsive systems shall lead to various advanced release processes on demand for biomedical applications.

  11. Peptide secreted by human alveolar macrophages releases neutrophil granule contents

    International Nuclear Information System (INIS)

    MacArthur, C.K.; Miller, E.J.; Cohen, A.B.

    1987-01-01

    A monoclonal antibody was developed against an 8000-kDa enzyme-releasing peptide (ERP) released from human alveolar macrophages. ERP was isolated on an immunoaffinity column containing the antibody bound to staphylococcal protein A-Sepharose, and by autoradiography. Release of ERP from the macrophages is not changed by plastic adherence, phagocytosis, calcium ionophore, or phorbol esters. The peptide was not antigenically similar to interferon-γ, tumor necrosis factor, or interleukin lα or 1β. The release of constituents from azurophilic and specific granules was the main identified biologic function of ERP. ERP was a more effective secretagogue in the untreated neutrophils and f-met-leu-phe was more effective in the cytochalasin B-treated neutrophils. Absorption of ERP from macrophage-conditioned medium removed a small amount of the chemotactic activity; however, the immunopurified peptide was not chemotactic or chemokinetic for neutrophils, and at high concentrations, it suppressed base line chemokinesis. Treatment of washed macrophages with trypsin released active ERP of approximately the same m.w. of spontaneously secreted ERP. These studies showed that human alveolar macrophages release a peptide which is a secretagogue for human neutrophils under conditions which may be encountered in the lungs during certain disease states. Proteolytic enzymes which are free in the lungs may release the peptide and lead to the secretion of neutrophil enzymes

  12. Toxic chemical considerations for tank farm releases. Revision 1

    Energy Technology Data Exchange (ETDEWEB)

    Van Keuren, J.C.

    1995-11-01

    This document provides a method of determining the toxicological consequences of accidental releases from Hanford Tank Farms. A determination was made of the most restrictive toxic chemicals that are expected to be present in the tanks. Concentrations were estimated based on the maximum sample data for each analyte in all the tanks in the composite. Composite evaluated were liquids and solids from single shell tanks, double shell tanks, flammable gas watch list tanks, as well as all solids, all liquids, head space gases, and 241-C-106 solids. A sum of fractions of the health effects was computed for each composite for unit releases based emergency response planning guidelines (ERPGs). Where ERPGs were not available for chemical compounds of interest, surrogate guidelines were established. The calculation method in this report can be applied to actual release scenarios by multiplying the sum of fractions by the release rate for continuous releases, or the release amount for puff releases. Risk guidelines are met if the product is less than for equal to one.

  13. Toxic chemical considerations for tank farm releases. Revision 1

    International Nuclear Information System (INIS)

    Van Keuren, J.C.

    1995-11-01

    This document provides a method of determining the toxicological consequences of accidental releases from Hanford Tank Farms. A determination was made of the most restrictive toxic chemicals that are expected to be present in the tanks. Concentrations were estimated based on the maximum sample data for each analyte in all the tanks in the composite. Composite evaluated were liquids and solids from single shell tanks, double shell tanks, flammable gas watch list tanks, as well as all solids, all liquids, head space gases, and 241-C-106 solids. A sum of fractions of the health effects was computed for each composite for unit releases based emergency response planning guidelines (ERPGs). Where ERPGs were not available for chemical compounds of interest, surrogate guidelines were established. The calculation method in this report can be applied to actual release scenarios by multiplying the sum of fractions by the release rate for continuous releases, or the release amount for puff releases. Risk guidelines are met if the product is less than for equal to one

  14. Minimizing lead release levels in secondary smelters slags

    International Nuclear Information System (INIS)

    Shenkler, E.S.; Graham, S.; Ghosh, R.; Greenhut, V.A.

    1991-01-01

    Five lead-containing slags and four mattes were analyzed to reveal microstructure, semi-quantitative microchemistry, and phases present. To determine if the slags could be incorporated as a glass so that lead release levels could be stabilized, glass batches were formulated based on slag compositions. Leaching tests showed that all materials that were fritted in a glass batch had lower lead release levels than non-adjusted materials, and all could satisfy EPA test requirements. The mole ratio of glass modifiers to glass formers played an important role in the extent of lead release. Small additions of phosphate to a batch had a significant effect on lowering lead release levels

  15. The influence of granulating solvents on drug release from tablets ...

    African Journals Online (AJOL)

    ... significantly lower than the other wet granulated tablets, but higher than the matrix tablets. The granulating solvent influenced the release of drug which increased with increase in the water content. Key Words: Grewia gum: Granulating solvents; Release mechanisms. Journal of Pharmacy and Bioresources Vol.1(1) 2004: ...

  16. Comparing fixed-amount and progressive-amount DRO Schedules for tic suppression in youth with chronic tic disorders.

    Science.gov (United States)

    Capriotti, Matthew R; Turkel, Jennifer E; Johnson, Rachel A; Espil, Flint M; Woods, Douglas W

    2017-01-01

    Chronic tic disorders (CTDs) involve motor and/or vocal tics that often cause substantial distress and impairment. Differential reinforcement of other behavior (DRO) schedules of reinforcement produce robust, but incomplete, reductions in tic frequency in youth with CTDs; however, a more robust reduction may be needed to affect durable clinical change. Standard, fixed-amount DRO schedules have not commonly yielded such reductions, so we evaluated a novel, progressive-amount DRO schedule, based on its ability to facilitate sustained abstinence from functionally similar behaviors. Five youth with CTDs were exposed to periods of baseline, fixed-amount DRO (DRO-F), and progressive-amount DRO (DRO-P). Both DRO schedules produced decreases in tic rate and increases in intertic interval duration, but no systematic differences were seen between the two schedules on any dimension of tic occurrence. The DRO-F schedule was generally preferred to the DRO-P schedule. Possible procedural improvements and other future directions are discussed. © 2016 Society for the Experimental Analysis of Behavior.

  17. Growth hormone (GH)-releasing activity of chicken GH-releasing hormone (GHRH) in chickens.

    Science.gov (United States)

    Harvey, S; Gineste, C; Gaylinn, B D

    2014-08-01

    Two peptides with sequence similarities to growth hormone releasing hormone (GHRH) have been identified by analysis of the chicken genome. One of these peptides, chicken (c) GHRH-LP (like peptide) was previously found to poorly bind to chicken pituitary membranes or to cloned and expressed chicken GHRH receptors and had little, if any, growth hormone (GH)-releasing activity in vivo or in vitro. In contrast, a second more recently discovered peptide, cGHRH, does bind to cloned and expressed cGHRH receptors and increases cAMP activity in transfected cells. The possibility that this peptide may have in vivo GH-releasing activity was therefore assessed. The intravenous (i.v.) administration of cGHRH to immature chickens, at doses of 3-100 μg/kg, significantly increased circulating GH concentrations within 10 min of injection and the plasma GH levels remained elevated for at least 30 min after the injection of maximally effective doses. The plasma GH responses to cGHRH were comparable with those induced by human (h) or porcine (p) GHRH preparations and to that induced by thyrotropin releasing hormone (TRH). In marked contrast, the i.v. injection of cGHRH-LP had no significant effect on circulating GH concentrations in immature chicks. GH release was also increased from slaughterhouse chicken pituitary glands perifused for 5 min with cGHRH at doses of 0.1 μg/ml or 1.0 μg/ml, comparable with GH responses to hGHRH1-44. In contrast, the perifusion of chicken pituitary glands with cGHRH-LP had no significant effect on GH release. In summary, these results demonstrate that cGHRH has GH-releasing activity in chickens and support the possibility that it is the endogenous ligand of the cGHRH receptor. Copyright © 2014 Elsevier Inc. All rights reserved.

  18. Quantifying Ca2+ release and inactivation of Ca2+ release in fast- and slow-twitch muscles.

    Science.gov (United States)

    Barclay, C J

    2012-12-01

    The aims of this study were to quantify the Ca(2+) release underlying twitch contractions of mammalian fast- and slow-twitch muscle and to comprehensively describe the transient inactivation of Ca(2+) release following a stimulus. Experiments were performed using bundles of fibres from mouse extensor digitorum longus (EDL) and soleus muscles. Ca(2+) release was quantified from the amount of ATP used to remove Ca(2+) from the myoplasm following stimulation. ATP turnover by crossbridges was blocked pharmacologically (N-benzyl-p-toluenesulphonamide for EDL, blebbistatin for soleus) and muscle heat production was used as an index of Ca(2+) pump ATP turnover. At 20°C, Ca(2+) release in response to a single stimulus was 34 and 84 μmol (kg muscle)(-1) for soleus and EDL, respectively, and increased with temperature (30°C: soleus, 61 μmol kg(-1); EDL, 168 μmol kg(-1)). Delivery of another stimulus within 100 ms of the first produced a smaller Ca(2+) release. The maximum magnitude of the decrease in Ca(2+) release was greater in EDL than soleus. Ca(2+) release recovered with an exponential time course which was faster in EDL (mean time constant at 20°C, 32.1 ms) than soleus (65.6 ms) and faster at 30°C than at 20°C. The amounts of Ca(2+) released and crossbridge cycles performed are consistent with a scheme in which Ca(2+) binding to troponin-C allowed an average of ∼1.7 crossbridge cycles in the two muscles.

  19. The Research and Application of Sustainable Long-release Carbon Material with Agricultural Waste

    Science.gov (United States)

    Wen, Z.

    2017-12-01

    (1) The element analysis shown that ten kinds of agricultural wastes containing a certain amount of C, N, H elements, the highest content of C element, and t value ranges from 36.02% 36.02%, and the variation of C, N, H elements content in difference materials was not significant. The TOC concentration of sugar cane was up to 38.66 mg·g-1, and quality ratio was 39‰, significantly lower than C elements content. The released TOC quality of the rest materials were 2.36 2.36 mg·g-1, and the order from high to low were the soybean straw, rice straw, corn straw, rice husk, poplar branches, wheat straw, reeds, corn cob and wood chips respectively. The long-term leaching experiment of selected Optimized agricultural waste showed that the TOC content in leaching solution rise rapidly to peak value and was stable afterwards, with the concentration of 4.59 19.46 mg·g-1. The TOC releasing amount order was same with the short-term leaching experiment. (2) The releasing of nitrate nitrogen in ten kinds of agricultural waste was low (corn straw was up to 0.12mg·g-1, and the rest were all below 0.04mg·g-1 without accumulation. Most of the ammonia nitrogen concentration in leachate was lower than 0.3mg·g-1. The kjeldahl nitrogen in the corn straw, soybean straw, rice straw, reed, rice husk, and sugar cane leachate (0.81 1.65mg·g-1) were higher than that of poplar branches, corn cob and wood chips (corn straw, rice husk and wheat straw leachate. Above all, it can be concluded that the sugar cane, corn straw, rice husk, wheat straw, corn cob, wood were ideal carbon source material in ten kinds of agricultural.

  20. Effect of increasing amounts of straw on pigs’ explorative behaviour

    DEFF Research Database (Denmark)

    Jensen, Margit Bak; Herskin, Mette S.; Forkman, Björn

    2015-01-01

    According to European legislation, pigs must have permanent access to sufficient quantity of materialto enable manipulation activities. However, few studies have quantified how much straw is needed tofulfil the requirements of growing pigs. We investigated the effect of increasing amount of straw...... on pigs’manipulation of the straw, and hypothesised that after a certain point increasing straw amount will nolonger increase oral manipulation further. From 30 to 80 kg live weight, pigs were housed in 90 groups of18 pigs in pens (5.48 m × 2.48 m) with partly slatted concrete floor and daily provided...... with the percentage ofpigs manipulating straw simultaneously. This was recorded in three 1-h intervals (1 h before and 1 h afterstraw allocation in the morning, as well as from 17 to 18 h in the afternoon). With increasing quantity ofstraw provided, we found a curvilinear (P increase in the time spent in oral...

  1. Another way of managing large amounts of data

    CERN Multimedia

    2009-01-01

    Jeff Hammerbacher is Vice President of Products and Chief Scientist at Cloudera, a US software company that provides solutions for managing and analysing very large data sets. His invited talk on 21 August was a good opportunity to exchange views with the CERN experts who face similar problems. Although still relatively young, Jeff has considerable experience in developing tools for storing and processing large amounts of data. Before Cloudera Jeff conceived, built and led the Data team at Facebook. He has also worked as a quantitative analyst on Wall Street. Jeff holds a Bachelor’s Degree in mathematics from Harvard University. At CERN, handling large amounts of data is the job of the Grid; Hadoop, the software Cloudera is developing, is intended for the same scope but has different technical features and implementations. "The Grid software products are designed for many organisations to collaborate on large-scale data analysis across many data centres. In contrast, Had...

  2. Hindered disulfide bonds to regulate release rate of model drug from mesoporous silica.

    Science.gov (United States)

    Nadrah, Peter; Maver, Uroš; Jemec, Anita; Tišler, Tatjana; Bele, Marjan; Dražić, Goran; Benčina, Mojca; Pintar, Albin; Planinšek, Odon; Gaberšček, Miran

    2013-05-01

    With the advancement of drug delivery systems based on mesoporous silica nanoparticles (MSNs), a simple and efficient method regulating the drug release kinetics is needed. We developed redox-responsive release systems with three levels of hindrance around the disulfide bond. A model drug (rhodamine B dye) was loaded into MSNs' mesoporous voids. The pore opening was capped with β-cyclodextrin in order to prevent leakage of drug. Indeed, in absence of a reducing agent the systems exhibited little leakage, while the addition of dithiothreitol cleaved the disulfide bonds and enabled the release of cargo. The release rate and the amount of released dye were tuned by the level of hindrance around disulfide bonds, with the increased hindrance causing a decrease in the release rate as well as in the amount of released drug. Thus, we demonstrated the ability of the present mesoporous systems to intrinsically control the release rate and the amount of the released cargo by only minor structural variations. Furthermore, an in vivo experiment on zebrafish confirmed that the present model delivery system is nonteratogenic.

  3. Amount of substance and the proposed redefinition of the mole

    Science.gov (United States)

    Milton, M. J. T.; Mills, I. M.

    2009-06-01

    There has been considerable discussion about the merits of redefining four of the base units of the SI, including the mole. In this paper, the options for implementing a new definition for the mole based on a fixed value for the Avogadro constant are discussed. They are placed in the context of the macroscopic nature of the quantity amount of substance and the opportunity to introduce a system for molar and atomic masses with unchanged values and consistent relative uncertainties.

  4. Infected Atopic Dermatitis Lesions Contain Pharmacologic Amounts of Lipoteichoic Acid

    Science.gov (United States)

    Travers, Jeffrey B.; Kozman, Amal; Mousdicas, Nico; Saha, Chandan; Landis, Megan; Al-Hassani, Mohammed; Yao, Weiguo; Yao, Yongxue; Hyatt, Ann-Marie; Sheehan, Michael P.; Haggstrom, Anita N.; Kaplan, Mark H.

    2009-01-01

    Background Bacterial infection with Staphylococcus aureus is a known trigger for worsening of atopic dermatitis (AD); the exact mechanisms by which bacterial infection worsens dermatitis are unknown. Objective We sought to characterize the amounts of the biologically active bacterial lipoprotein lipoteichoic acid (LTA) in infected AD lesions. Methods Eighty-nine children with clinically impetiginized lesions of AD were enrolled in this study. A lesion was graded clinically using the Eczema Area and Severity Index (EASI), and then wash fluid obtained from the lesion for quantitative bacterial culture, and measurement of LTA and cytokines. The staphylococcal isolate was tested for antibiotic susceptibilities. The patients were treated with a regimen that included topical corticosteroids and systemic antibiotics and the lesion was re-analyzed after two weeks. Results S. aureus was identified in 79 of 89 children enrolled in the study. The bacterial CFU correlated with the EASI lesional score (p = 0.04). LTA levels up to 9.8 μg/ml were measured in the wash fluid samples and the amounts correlated with the lesional EASI scores (p = 0.01) and S. aureus CFU (p < 0.001). Approximately 30% of clinically impetiginized AD lesions contained greater than 1 μg/ml LTA, amounts that exert effects on various cell types in vitro. Moreover, injection of skin tissue ex vivo with amounts of LTA found in AD lesions resulted in epidermal cytokine gene expression. Conclusions Pharmacologic levels of LTA are found in many infected atopic dermatitis lesions. Clinical Implications These findings suggest that staphylococcal LTA could be an important mediator of the increased skin inflammation associated with infected AD. Capsule Summary These studies demonstrate high levels of staphylococcal LTA are found on impetiginized AD lesions. Moreover, subjects harboring MRSA exhibited greater total body involvement of AD. PMID:19962742

  5. Forest amount affects soybean productivity in Brazilian agricultural frontier

    Science.gov (United States)

    Rattis, L.; Brando, P. M.; Marques, E. Q.; Queiroz, N.; Silverio, D. V.; Macedo, M.; Coe, M. T.

    2017-12-01

    Over the past three decades, large tracts of tropical forests have been converted to crop and pasturelands across southern Amazonia, largely to meet the increasing worldwide demand for protein. As the world's population continue to grow and consume more protein per capita, forest conversion to grow more crops could be a potential solution to meet such demand. However, widespread deforestation is expected to negatively affect crop productivity via multiple pathways (e.g., thermal regulation, rainfall, local moisture, pest control, among others). To quantify how deforestation affects crop productivity, we modeled the relationship between forest amount and enhanced vegetation index (EVI—a proxy for crop productivity) during the soybean planting season across southern Amazonia. Our hypothesis that forest amount causes increased crop productivity received strong support. We found that the maximum MODIS-based EVI in soybean fields increased as a function of forest amount across three spatial-scales, 0.5 km, 1 km, 2 km, 5 km, 10 km, 15 km and 20 km. However, the strength of this relationship varied across years and with precipitation, but only at the local scale (e.g., 500 meters and 1 km radius). Our results highlight the importance of considering forests to design sustainable landscapes.

  6. INVESTIGATION OF DRUG RELEASE FROM BIODEGRADABLE PLG MICROSPHERES: EXPERIMENT AND THEORY

    Energy Technology Data Exchange (ETDEWEB)

    ANDREWS, MALCOLM J. [Los Alamos National Laboratory; BERCHANE, NADER S. [Los Alamos National Laboratory; CARSON, KENNETH H. [Los Alamos National Laboratory; RICE-FICHT, ALLISON C. [Los Alamos National Laboratory

    2007-01-30

    Piroxicam containing PLG microspheres having different size distributions were fabricated, and in vitro release kinetics were determined for each preparation. Based on the experimental results, a suitable mathematical theory has been developed that incorporates the effect of microsphere size distribution and polymer degradation on drug release. We show from in vitro release experiments that microsphere size has a significant effect on drug release rate. The initial release rate decreased with an increase in microsphere size. In addition, the release profile changed from first order to concave-upward (sigmoidal) as the system size was increased. The mathematical model gave a good fit to the experimental release data.

  7. An experimental test of the habitat-amount hypothesis for saproxylic beetles in a forested region.

    Science.gov (United States)

    Seibold, Sebastian; Bässler, Claus; Brandl, Roland; Fahrig, Lenore; Förster, Bernhard; Heurich, Marco; Hothorn, Torsten; Scheipl, Fabian; Thorn, Simon; Müller, Jörg

    2017-06-01

    The habitat-amount hypothesis challenges traditional concepts that explain species richness within habitats, such as the habitat-patch hypothesis, where species number is a function of patch size and patch isolation. It posits that effects of patch size and patch isolation are driven by effects of sample area, and thus that the number of species at a site is basically a function of the total habitat amount surrounding this site. We tested the habitat-amount hypothesis for saproxylic beetles and their habitat of dead wood by using an experiment comprising 190 plots with manipulated patch sizes situated in a forested region with a high variation in habitat amount (i.e., density of dead trees in the surrounding landscape). Although dead wood is a spatio-temporally dynamic habitat, saproxylic insects have life cycles shorter than the time needed for habitat turnover and they closely track their resource. Patch size was manipulated by adding various amounts of downed dead wood to the plots (~800 m³ in total); dead trees in the surrounding landscape (~240 km 2 ) were identified using airborne laser scanning (light detection and ranging). Over 3 yr, 477 saproxylic species (101,416 individuals) were recorded. Considering 20-1,000 m radii around the patches, local landscapes were identified as having a radius of 40-120 m. Both patch size and habitat amount in the local landscapes independently affected species numbers without a significant interaction effect, hence refuting the island effect. Species accumulation curves relative to cumulative patch size were not consistent with either the habitat-patch hypothesis or the habitat-amount hypothesis: several small dead-wood patches held more species than a single large patch with an amount of dead wood equal to the sum of that of the small patches. Our results indicate that conservation of saproxylic beetles in forested regions should primarily focus on increasing the overall amount of dead wood without considering its

  8. The radiological significance of beta emitting hot particles released from the Chernobyl nuclear power plant

    International Nuclear Information System (INIS)

    Hofmann, W.; Crawford-Brown, D.J.; Martonen, T.B.

    1988-01-01

    In order to assess radiological hazards associated with inhalation of beta emitting hot particles detected in fall-out from the Chernobyl incident, radiation doses and lung cancer risk are calculated for a hot particle composed entirely of 103 Ru. Lung cancer risk estimates are based upon an initiation-promotion model of carcinogenesis. In the immediate vicinity of a hot particle, calculations indicate that doses may be extremely high, so that all cells are killed and no tumour will arise. At intermediate distances, however, the probability for lung cancer induction exhibits a distinct maximum. Risk enhancement factors, computed relative to a uniform radionuclide distribution of equal activity, are highest for intermediate activities and hot particles moving in the lung. While the risk from inhalation of 103 Ru hot particles might, indeed, exceed that from all other exposure pathways of the Chernobyl fall-out, it still lies within normal fluctuations of radon progeny induced lung cancer risk. (author)

  9. The significance of ground contamination following an accidental release of radioactivity

    International Nuclear Information System (INIS)

    Corbett, J.O.

    1977-07-01

    The reasons for extending the analysis of hypothetical accidents to include ground contamination as a route to radiation dosage in man are discussed. Models and data available for such an assessment of ground contamination are examined with reference to the deposition of radionuclides from the atmosphere and dosage by direct γ-irradiation, ingestion of radionuclides in milk and inhalation of a resuspended aerosol. Dosage through these routes is then compared with that which arises directly from the plume emitted in a hypothetical accident. The assessment methods are subject to uncertainty, so that in some cases only an upper limit to dose or an estimate within an order of magnitude can be obtained. Areas where further research could lead to a reduction of this uncertainty are identified. (author)

  10. The influence of "host release factor" on carbon release by zooxanthellae isolated from fed and starved Aiptasia pallida (Verrill).

    Science.gov (United States)

    Davy, S K; Cook, C B

    2001-06-01

    Symbiotic dinoflagellates (zooxanthellae) typically respond to extracts of host tissue with enhanced release of short-term photosynthetic products. We examined this "host release factor" (HRF) response using freshly isolated zooxanthellae of differing nutritional status. The nutritional status was manipulated by either feeding or starving the sea anemone Aiptasia pallida (Verrill). The release of fixed carbon from isolated zooxanthellae was measured using 14C in 30 min experiments. Zooxanthellae in filtered seawater alone released approximately 5% of photosynthate irrespective of host feeding history. When we used a 10-kDa ultrafiltrate of A. pallida host tissue as a source of HRF, approximately 14% of photosynthate was released to the medium. This increased to over 25% for zooxanthellae from anemones starved for 29 days or more. The cell-specific photosynthetic rate declined with starvation in these filtrate experiments, but the decline was offset by the increased percentage release. Indeed, the total amount of released photosynthate remained unchanged, or even increased, as zooxanthellae became more nutrient deficient. Similar trends were also observed when zooxanthellae from A. pallida were incubated in a 3-kDa ultrafiltrate of the coral Montastraea annularis, suggesting that HRF in the different filtrates operated in a similar manner. Our results support the suggestion that HRF diverts surplus carbon away from storage compounds to translocated compounds such as glycerol.

  11. Release strategies for rehabilitated sea otters

    Science.gov (United States)

    DeGange, Anthony R.; Ballachey, Brenda E.; Bayha, Keith; Williams, Terrie M.; Davis, Randall W.

    1995-01-01

    According to the U.S. Fish and Wildlife Services’ (USFWS) Response Plan for sea otters (USFWS, in preparation), in the event of an oil spill, the decision to release sea otters from rehabilitation centers following treatment will be linked to the decision on whether to capture sea otters for treatment. Assuming a scenario similar to the Exxon Valdez oil spill (EVOS), once the decision to capture sea otters is made, the ultimate goal is to return as many sea otters to the wild as possible, even though the rescue may not be expected to produce results significant at the population level. The decision by the USFWS to proceed with capture, rehabilitation, and release will be made on a case-by-case basis (USFWS, in preparation). Many factors will influence the decision. Perhaps the most important factors in deciding when and where to release sea otters are the location and availability of suitable release sites and verification that the otters are free of diseases that might be transmitted to the wild population.Alternative release strategies for sea otters will be contained in the sea otter response portion of the USFWS’s oil spill contingency plans for Alaska and California that are being developed as required by the Oil Pollution Act of 1990. Public review of these plans before they are implemented will help to reduce public concern about the survival of rehabilitated otters, their biological effect on the release area, and the potential introduction or spread of disease into the wild sea otter population.The objective of this chapter is to review alternative strategies for the disposition of rehabilitated sea otters. Our assumption is that returning as many animals to the wild as possible, whether it be for humanitarian or biological reasons, is the ultimate goal of this effort (Figure 10.1).

  12. Simplified assessment of segmental gastrointestinal transit time with orally small amount of barium

    Energy Technology Data Exchange (ETDEWEB)

    Yuan, Weitang; Zhang, Zhiyong; Liu, Jinbo; Li, Zhen; Song, Junmin; Wu, Changcai [Department of Colorectal Surgery, The First Affiliated Hospital and Institute of Clinical Medicine, Zhengzhou University, 450052 Zhengzhou (China); Wang, Guixian, E-mail: guixianwang@hotmail.com [Department of Colorectal Surgery, The First Affiliated Hospital and Institute of Clinical Medicine, Zhengzhou University, 450052 Zhengzhou (China)

    2012-09-15

    Objective: To determine the effectiveness and advantage of small amount of barium in the measurement of gastrointestinal transmission function in comparison with radio-opaque pallets. Methods: Protocal 1: 8 healthy volunteers (male 6, female 2) with average age 40 ± 6.1 were subjected to the examination of radio-opaque pellets and small amount of barium with the interval of 1 week. Protocol 2: 30 healthy volunteers in group 1 (male 8, female 22) with average age 42.5 ± 8.1 and 50 patients with chronic functional constipation in group 2 (male 11, female 39) with average age 45.7 ± 7.8 were subjected to the small amount of barium examination. The small amount of barium was made by 30 g barium dissolved in 200 ml breakfast. After taking breakfast which contains barium, objectives were followed with abdominal X-ray at 4, 8, 12, 24, 48, 72, 96 h until the barium was evacuated totally. Results: Small amount of barium presented actual chyme or stool transit. The transit time of radio-opaque pallets through the whole gastrointestinal tract was significantly shorter than that of barium (37 ± 8 h vs. 47 ± 10 h, P < 0.05) in healthy people. The transit times of barium in constipation patients were markedly prolonged in colon (61.1 ± 22 vs. 37.3 ± 11, P < 0.01) and rectum (10.8 ± 3.7 vs. 2.3 ± 0.8 h, P < 0.01) compared with unconstipated volunteers. Transit times in individual gastrointestinal segments were also recorded by using small amount of barium, which allowed identifying the subtypes of constipation. Conclusion: The small amount barium examination is a convenient and low cost method to provide the most useful and reliable information on the transmission function of different gastrointestinal segments and able to classify the subtypes of slow transit constipation.

  13. Simplified assessment of segmental gastrointestinal transit time with orally small amount of barium

    International Nuclear Information System (INIS)

    Yuan, Weitang; Zhang, Zhiyong; Liu, Jinbo; Li, Zhen; Song, Junmin; Wu, Changcai; Wang, Guixian

    2012-01-01

    Objective: To determine the effectiveness and advantage of small amount of barium in the measurement of gastrointestinal transmission function in comparison with radio-opaque pallets. Methods: Protocal 1: 8 healthy volunteers (male 6, female 2) with average age 40 ± 6.1 were subjected to the examination of radio-opaque pellets and small amount of barium with the interval of 1 week. Protocol 2: 30 healthy volunteers in group 1 (male 8, female 22) with average age 42.5 ± 8.1 and 50 patients with chronic functional constipation in group 2 (male 11, female 39) with average age 45.7 ± 7.8 were subjected to the small amount of barium examination. The small amount of barium was made by 30 g barium dissolved in 200 ml breakfast. After taking breakfast which contains barium, objectives were followed with abdominal X-ray at 4, 8, 12, 24, 48, 72, 96 h until the barium was evacuated totally. Results: Small amount of barium presented actual chyme or stool transit. The transit time of radio-opaque pallets through the whole gastrointestinal tract was significantly shorter than that of barium (37 ± 8 h vs. 47 ± 10 h, P < 0.05) in healthy people. The transit times of barium in constipation patients were markedly prolonged in colon (61.1 ± 22 vs. 37.3 ± 11, P < 0.01) and rectum (10.8 ± 3.7 vs. 2.3 ± 0.8 h, P < 0.01) compared with unconstipated volunteers. Transit times in individual gastrointestinal segments were also recorded by using small amount of barium, which allowed identifying the subtypes of constipation. Conclusion: The small amount barium examination is a convenient and low cost method to provide the most useful and reliable information on the transmission function of different gastrointestinal segments and able to classify the subtypes of slow transit constipation

  14. Effects of picture amount on preference, balance, and dynamic feel of Web pages.

    Science.gov (United States)

    Chiang, Shu-Ying; Chen, Chien-Hsiung

    2012-04-01

    This study investigates the effects of picture amount on subjective evaluation. The experiment herein adopted two variables to define picture amount: column ratio and picture size. Six column ratios were employed: 7:93,15:85, 24:76, 33:67, 41:59, and 50:50. Five picture sizes were examined: 140 x 81, 220 x 127, 300 x 173, 380 x 219, and 460 x 266 pixels. The experiment implemented a within-subject design; 104 participants were asked to evaluate 30 web page layouts. Repeated measurements revealed that the column ratio and picture size have significant effects on preference, balance, and dynamic feel. The results indicated the most appropriate picture amount for display: column ratios of 15:85 and 24:76, and picture sizes of 220 x 127, 300 x 173, and 380 x 219. The research findings can serve as the basis for the application of design guidelines for future web page interface design.

  15. Variations of measured and simulated soil-loss amounts in a semiarid area in Turkey.

    Science.gov (United States)

    Hacisalihoğlu, Sezgin

    2010-06-01

    The main goal of this research was soil-loss determination and comparison of the plot measurement results with simulation model (universal soil loss equation (USLE)) results in different land use and slope classes. The research took place in three different land-use types (Scotch pine forest, pasture land, and agricultural land) and in two different slope classes (15-20%, 35-40%). Within six measurement stations (for each land-use type and slope class-one station), totally 18 measurement plots have been constituted, and soil-loss amount measurements have been investigated during the research period (3 years along). USLE simulation model is used in these measurement plots for calculation the soil-loss amounts. The results pointed out that measured (in plots) and simulated (with USLE) soil-loss amounts differ significantly in each land-use type and slope class.

  16. Press Oil Final Release Survey

    Energy Technology Data Exchange (ETDEWEB)

    Whicker, Jeffrey Jay [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Ruedig, Elizabeth [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2017-05-11

    There are forty-eight 55 gallon barrels filled with hydraulic oil that are candidates for release and recycle. This oil needs to be characterized prior to release. Principles of sampling as provided in MARSAME/MARSSIM approaches were used as guidance for sampling.

  17. Workload Control with Continuous Release

    NARCIS (Netherlands)

    Phan, B. S. Nguyen; Land, M. J.; Gaalman, G. J. C.

    2009-01-01

    Workload Control (WLC) is a production planning and control concept which is suitable for the needs of make-to-order job shops. Release decisions based on the workload norms form the core of the concept. This paper develops continuous time WLC release variants and investigates their due date

  18. Systemic levels of metallic ions released from orthodontic mini-implants.

    Science.gov (United States)

    de Morais, Liliane Siqueira; Serra, Glaucio Guimarães; Albuquerque Palermo, Elisabete Fernandes; Andrade, Leonardo Rodrigues; Müller, Carlos Alberto; Meyers, Marc André; Elias, Carlos Nelson

    2009-04-01

    Orthodontic mini-implants are a potential source of metallic ions to the human body because of the corrosion of titanium (Ti) alloy in body fluids. The purpose of this study was to gauge the concentration of Ti, aluminum (Al), and vanadium (V), as a function of time, in the kidneys, livers, and lungs of rabbits that had Ti-6Al-4V alloy orthodontic mini-implants placed in their tibia. Twenty-three New Zealand rabbits were randomly divided into 4 groups: control, 1 week, 4 weeks, and 12 weeks. Four orthodontic mini-implants were placed in the left proximal tibia of 18 rabbits. Five control rabbits had no orthodontic mini-implants. After 1, 4, and 12 weeks, the rabbits were killed, and the selected tissues were extracted and prepared for analysis by graphite furnace atomic absorption spectrophotometry. Low amounts of Ti, Al, and V were detectable in the 1-week, 4-weeks, and 12-weeks groups, confirming that release of these metals from the mini-implants occurs, with diffusion and accumulation in remote organs. Despite the tendency of ion release when using the Ti alloy as orthodontic mini-implants, the amounts of metals detected were significantly below the average intake of these elements through food and drink and did not reach toxic concentrations.

  19. Effects of prostaglandin E2 and cAMP elevating drugs on GM-CSF release by cultured human airway smooth muscle cells. Relevance to asthma therapy.

    Science.gov (United States)

    Lazzeri, N; Belvisi, M G; Patel, H J; Yacoub, M H; Chung, K F; Mitchell, J A

    2001-01-01

    Human airway smooth muscle (HASM) cells release granulocyte macrophage-colony stimulating factor (GM-CSF) and express cyclooxygenase (COX)-2 (resulting in the release of prostaglandin [PG] E2) after stimulation with cytokines. Because COX-2 activity can regulate a number of inflammatory processes, we have assessed its effects, as well as those of agents that modulate cyclic adenosine monophosphate (cAMP), on GM-CSF release by HASM cells. Cells stimulated with a combination of proinflammatory cytokines (interleukin-1beta and tumor necrosis factor-alpha each at 10 ng/ml) for 24 h released significant amounts of PGE2 (measured by radioimmunoassay) and GM-CSF (measured by enzyme-linked immunosorbent assay). Indomethacin and other COX-1/COX-2 inhibitors caused concentration-dependent inhibitions of PGE2 concomitantly with increases in GM-CSF formation. Addition of exogenous PGE2 or the beta2-agonist fenoterol, which increase cAMP, to cytokine-treated HASM cells had no effect on GM-CSF release unless COX activity was first blocked with indomethacin. The type 4 phosphodiesterase inhibitors rolipram and SB 207499 both caused concentration-dependent reductions in GM-CSF production. Thus, when HASM cells are activated with cytokines they release PGE2, which acts as a "braking mechanism" to limit the coproduction of GM-CSF. Moreover, agents that elevate cAMP also reduce GM-CSF formation by these cells.

  20. Significant exposures to isoeugenol derivaties in perfumes

    DEFF Research Database (Denmark)

    Rastogi, Suresh Chandra; Johansen, Jeanne Duus

    2008-01-01

    in perfumes/aftershaves. MATERIALS AND METHODS: 29 international brand perfumes/aftershaves were analysed for the target fragrance ingredient by gas chromatography-mass spectrometry. All samples were analysed in duplicate at detection levels of 1-5 p.p.m. RESULTS: 16 products (55%) contained isoeugenol...... was not detected in any of the investigated products. CONCLUSIONS: Isoeugenyl acetate is present in perfumes/aftershaves, in some products in significant amounts. This may lead to elicitation of contact allergy in isoeugenol-sensitized individuals and may contribute to unchanged levels of isoeugenol sensitization....

  1. Return period curves for extreme 5-min rainfall amounts at the Barcelona urban network

    Science.gov (United States)

    Lana, X.; Casas-Castillo, M. C.; Serra, C.; Rodríguez-Solà, R.; Redaño, A.; Burgueño, A.; Martínez, M. D.

    2018-03-01

    Heavy rainfall episodes are relatively common in the conurbation of Barcelona and neighbouring cities (NE Spain), usually due to storms generated by convective phenomena in summer and eastern and south-eastern advections in autumn. Prevention of local flood episodes and right design of urban drainage have to take into account the rainfall intensity spread instead of a simple evaluation of daily rainfall amounts. The database comes from 5-min rain amounts recorded by tipping buckets in the Barcelona urban network along the years 1994-2009. From these data, extreme 5-min rain amounts are selected applying the peaks-over-threshold method for thresholds derived from both 95% percentile and the mean excess plot. The return period curves are derived from their statistical distribution for every gauge, describing with detail expected extreme 5-min rain amounts across the urban network. These curves are compared with those derived from annual extreme time series. In this way, areas in Barcelona submitted to different levels of flood risk from the point of view of rainfall intensity are detected. Additionally, global time trends on extreme 5-min rain amounts are quantified for the whole network and found as not statistically significant.

  2. A radiolabel release microassay for phagocytic killing of Candida albicans

    International Nuclear Information System (INIS)

    Bistoni, F.; Baccarini, M.; Blasi, E.; Marconi, P.; Puccetti, P.

    1982-01-01

    The chromium-51 release technique for quantifying intracellular killing of radiolabelled Candida albicans particles was exploited in a microassay in which murine and human phagocytes acted as effectors under peculiarly simple conditions. At appropriate effector: target ratios and with a 4 h incubation, up to 50% specific chromium release could be detected in the supernatant with no need for opsonization or lysis of phagocytes. This simple microassay permits easy-to-perform, simultaneous testing of a variety of different phagocytes even if only available in limited amounts, and provides an objective measurement of intracellular killing of Candida albicans. (Auth.)

  3. Cytotoxic effects of glass ionomer cements on human dental pulp stem cells correlate with fluoride release.

    Science.gov (United States)

    Kanjevac, Tatjana; Milovanovic, Marija; Volarevic, Vladislav; Lukic, Miodrag L; Arsenijevic, Nebojsa; Markovic, Dejan; Zdravkovic, Nebojsa; Tesic, Zivoslav; Lukic, Aleksandra

    2012-01-01

    Glass ionomer cements (GICs) are commonly used as restorative materials. Responses to GICs differ among cell types and it is therefore of importance to thoroughly investigate the influence of these restorative materials on pulp stem cells that are potential source for dental tissue regeneration. Eight biomaterials were tested: Fuji I, Fuji II, Fuji VIII, Fuji IX, Fuji Plus, Fuji Triage, Vitrebond and Composit. We compared their cytotoxic activity on human dental pulp stem cells (DPSC) and correlated this activity with the content of Fluoride, Aluminium and Strontium ions in their eluates. Elution samples of biomaterials were prepared in sterile tissue culture medium and the medium was tested for toxicity by an assay of cell survival/proliferation (MTT test) and apoptosis (Annexin V FITC Detection Kit). Concentrations of Fluoride, Aluminium and Strontium ions were tested by appropriate methods in the same eluates. Cell survival ranged between 79.62% (Fuji Triage) to 1.5% (Fuji Plus) and most dead DPSCs were in the stage of late apoptosis. Fluoride release correlated with cytotoxicity of GICs, while Aluminium and Strontium ions, present in significant amount in eluates of tested GICs did not. Fuji Plus, Vitrebond and Fuji VIII, which released fluoride in higher quantities than other GICs, were highly toxic to human DPSCs. Opposite, low levels of released fluoride correlated to low cytotoxic effect of Composit, Fuji I and Fuji Triage.

  4. Making lasting memories: Remembering the significant

    Science.gov (United States)

    McGaugh, James L.

    2013-01-01

    Although forgetting is the common fate of most of our experiences, much evidence indicates that emotional arousal enhances the storage of memories, thus serving to create, selectively, lasting memories of our more important experiences. The neurobiological systems mediating emotional arousal and memory are very closely linked. The adrenal stress hormones epinephrine and corticosterone released by emotional arousal regulate the consolidation of long-term memory. The amygdala plays a critical role in mediating these stress hormone influences. The release of norepinephrine in the amygdala and the activation of noradrenergic receptors are essential for stress hormone-induced memory enhancement. The findings of both animal and human studies provide compelling evidence that stress-induced activation of the amygdala and its interactions with other brain regions involved in processing memory play a critical role in ensuring that emotionally significant experiences are well-remembered. Recent research has determined that some human subjects have highly superior autobiographic memory of their daily experiences and that there are structural differences in the brains of these subjects compared with the brains of subjects who do not have such memory. Understanding of neurobiological bases of such exceptional memory may provide additional insights into the processes underlying the selectivity of memory. PMID:23754441

  5. Canine stifle stability following cranial cruciate ligament transection and medial meniscal release

    DEFF Research Database (Denmark)

    Vedel, T.; Kristiansen, S.; Jensen, Bente Rona

    stifle stability was evaluated in right pelvic limbs from canine cadavers under three different test situations (intact, CrCL deficient and medial meniscal release (MMR)). Dogs were euthanized for reasons unrelated to the study, owner approval given for research use and institutional ethical approval...... to an intact stifle PTA between 95.5° and 97°. The mean maximal CTS in CrCL deficient stifles was 52.8% of intact marker separation distance, occurring at an average joint angle of 130°, equivalent to an intact PTA of 109°.After MMR, CTS initiated significantly earlier in extension, at a joint angle of 65...... meniscus, but did not cause a significant change in the maximal amount of CTS....

  6. Smoking-induced dopamine release studied with [11C]raclopride PET

    International Nuclear Information System (INIS)

    Kim, Yu Kyeong; Cho, Sang Soo; Lee, Do Hoon

    2005-01-01

    It has been postulated that dopamine release in the striatum underlies the reinforcing properties of nicotine. Substantial evidence in the animal studies demonstrates that nicotine interacts with and regulates the activation of the dopaminergic neuron. The aim of this study was to visualize the dopamine release by smoking in human brain using PET scan with [ 11 C]raclopride. Four male non-smokers or ex-smokers with an abstinence period longer than 1 year (mean age of 24.3±2.6 years) were enrolled in this study. Dopamine D2 receptor radioligand, [ 11 C]raclopride was administrated with bolus-plus-constant infusion. Dynamic PET was performed during 120 minutes (3x20s, 2x60s, 2x120s, 1x180s and 22x300s). Following the 50 minute-scanning, subjects smoked a cigarette containing 1 mg of nicotine while in the scanner. Blood samples for the measurements of plasma nicotine levels were collected at 0, 5, 10, 15, 20, 25, 30, 45, 60, and 90 minute after smoking. Regions for striatal structures were drawn on the coronal summed PET images guided with co-registered MRI. Binding potential, calculated as striatal-cerebellar/cerebellar activity, was measured under equilibrium condition at baseline and smoking session. The mean change in binding potential between the baseline and smoking in caudate, Putamen and ventral striatum was 3.7 % , 4.0 % and 8.6 %, respectively. This indicated the striatal dopamine release by smoking. The reduction in binding potential in the ventral striatum was significantly correlated with the cumulated plasma level of the nicotine (r 2 =0.91, p=0.04). These data demonstrate that in vivo imaging with [ 11 C]raclopride PET could measure nicotine-induced dopamine release in the human brain, which has a significant positive correlation with the amount of nicotine administered by smoking

  7. Smoking-induced dopamine release studied with [{sup 11}C]raclopride PET

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Yu Kyeong; Cho, Sang Soo; Lee, Do Hoon [Seoul National University College of Medicine, Seoul (Korea, Republic of)] (and others)

    2005-07-01

    It has been postulated that dopamine release in the striatum underlies the reinforcing properties of nicotine. Substantial evidence in the animal studies demonstrates that nicotine interacts with and regulates the activation of the dopaminergic neuron. The aim of this study was to visualize the dopamine release by smoking in human brain using PET scan with [{sup 11}C]raclopride. Four male non-smokers or ex-smokers with an abstinence period longer than 1 year (mean age of 24.3{+-}2.6 years) were enrolled in this study. Dopamine D2 receptor radioligand, [{sup 11}C]raclopride was administrated with bolus-plus-constant infusion. Dynamic PET was performed during 120 minutes (3x20s, 2x60s, 2x120s, 1x180s and 22x300s). Following the 50 minute-scanning, subjects smoked a cigarette containing 1 mg of nicotine while in the scanner. Blood samples for the measurements of plasma nicotine levels were collected at 0, 5, 10, 15, 20, 25, 30, 45, 60, and 90 minute after smoking. Regions for striatal structures were drawn on the coronal summed PET images guided with co-registered MRI. Binding potential, calculated as striatal-cerebellar/cerebellar activity, was measured under equilibrium condition at baseline and smoking session. The mean change in binding potential between the baseline and smoking in caudate, Putamen and ventral striatum was 3.7 % , 4.0 % and 8.6 %, respectively. This indicated the striatal dopamine release by smoking. The reduction in binding potential in the ventral striatum was significantly correlated with the cumulated plasma level of the nicotine (r{sup 2}=0.91, p=0.04). These data demonstrate that in vivo imaging with [{sup 11}C]raclopride PET could measure nicotine-induced dopamine release in the human brain, which has a significant positive correlation with the amount of nicotine administered by smoking.

  8. Activated platelets release sphingosine 1-phosphate and induce hypersensitivity to noxious heat stimuli in vivo

    Directory of Open Access Journals (Sweden)

    Daniela eWeth

    2015-04-01

    Full Text Available At the site of injury activated platelets release various mediators, one of which is sphingosine 1-phosphate (S1P. It was the aim of this study to explore whether activated human platelets had a pronociceptive effect in an in vivo mouse model and whether this effect was based on the release of S1P and subsequent activation of neuronal S1P receptors 1 or 3. Human platelets were prepared in different concentrations (105/µl, 106/µl, 107/µl and assessed in mice with different genetic backgrounds (WT, S1P1fl/fl, SNS-S1P1-/-, S1P3-/-. Intracutaneous injections of activated human platelets induced a significant, dose-dependent hypersensitivity to noxious thermal stimulation. The degree of heat hypersensitivity correlated with the platelet concentration as well as the platelet S1P content and the amount of S1P released upon platelet activation as measured with LC MS/MS. Despite the significant correlations between S1P and platelet count, no difference in paw withdrawal latency (PWL was observed in mice with a global null mutation of the S1P3 receptor or a conditional deletion of the S1P1 receptor in nociceptive primary afferents. Furthermore, neutralisation of S1P with a selective anti-S1P antibody did not abolish platelet induced heat hypersensitivity. Our results suggest that activated platelets release S1P and induce heat hypersensitivity in vivo. However, the platelet induced heat hypersensitivity was caused by mediators other than S1P.

  9. Amount and composition of rain failing at Rothamsted

    Energy Technology Data Exchange (ETDEWEB)

    Russell, E J; Richards, E H

    1919-01-01

    The monthly fluctuations in the ammoniacal concentration varies with rainfall, i.e., highest in spring; lowest in winter. The nitric nitrogen concentration fluctuated year by year and month by month in the same way as the ammoniacal nitrogen and the rainfall until 1910, since when there has been no simple relationship. The close relationship between the amounts of ammoniacal and nitric nitrogen suggests either a common origin or the production of nitric compounds from ammonia. Chlorine fluctuations closely follow the rainfall also. Since 1888, when the experiments began, to 1916, when they terminated, there has been a rise in the amounts of nitric nitrogen and of chlorine in the rain. In the case of chlorine a parallel series of determinations made at Cirencester over the same period shows a similar rise. There is no rise of ammonia but on the contrary a tendency to drop; the sum of ammoniacal and nitric nitrogen shows little change over the period. This seems to suggest that a former source of ammonia is now turning out nitric acid. It is possible that modern gas burners and grates tend to the formation of nitric oxides rather than of ammonia. Rain contains on an average 10 parts of dissolved oxygen per million, the amount being higher in winter than in summer: 66.4 lb per acre per annum was brought down during the two years over which the determinations extended. The marked difference in composition between summer and winter rainfall suggests that these may differ in their origin. The winter rain resembles Atlantic rain in its high chlorine and low ammonia and nitrate content; the summer rain is characterized by low chlorine but high ammonia and nitrate content, suggesting that it arises by evaporation of water from the soil and condensation at higher altitudes than in the case of winter rain.

  10. DEFERRED TAXES GENERATED BY THE CAPITALIZED INTERESTS IN THE AMOUNT

    Directory of Open Access Journals (Sweden)

    PALIU – POPA LUCIA

    2015-08-01

    Full Text Available According to the General Framework for preparing and presenting the financial statements elaborated by IASB, the utility of information is provided by attributes (qualitative features, such as: intelligibility, relevance, credibility and comparability. For being credible, the financial information shall be erroneous, shall not be biased or deforming the patrimony, and one of the elements representing and defining the information credibility is the prudency. Thus, the prudential accounting treatments affect, on the one hand, the accounting information relevance and credibility, and on the other hand, equally, both the producers as well as the users of the financial information, due to the economic consequences which are generated. From this perspective and considering that the implied economic agents are not neutral in terms of their option concerning the neutral accounting practices, prudent or aggressive, we opined that it is useful to conduct a study aiming the relevance of the accounting information related to the deferred taxes generated by the capitalized interests in the amount of the fix assets, recognizing the value of these taxes having as result the compliance with the principle of prudency within the accountancy. In this context, compared to the dominant accounting systems, respectively the continental system and the Anglo- Saxon system, within which the accounting information is characterized as legal, respectively addressed to the external users, especially to the investors, the conducted study aimed the following directions: the main differences between the provisions of the national, European, Anglo-Saxon accounting regulations and those of the international referential related to the prudency; the occurrence and evolution of the deferred taxes generated by the capitalized interests in the amount of the fix assets; informational benefits of the accounting prudency concerning the reflection of the deferred taxes established by the

  11. Estimation of cobalt release from feed water heater tubes of BWRs

    International Nuclear Information System (INIS)

    Uchida, S.; Kitamura, M.; Ozawa, Y.

    1983-01-01

    To evaluate the release source of cobalt from heater tubes of the feed water line, release rate measurements were carried out by detecting 60 Co released from irradiated stainless steel in contact with neutral water at an oxygen concentration of 20 ppb. The dependences of cobalt release rate on temperature, flow velocity and exposure time were studied after 670 hours of release experiments, and an empirical equation (which is presented) was obtained in the temperature range from 150 to 240 deg C. A decrease in the cobalt release rate above 250 deg C was considered due to the formation of a protective oxide layer. From these data, the amount of cobalt released from individual feed water heaters was evaluated. It was demonstrated that low cobalt containing stainless steel was economically applied only in the higher temperature region of the heater (20% of the total surface) to reduce cobalt feed rate into the reactor (to approx. 1/2). (author)

  12. The effect of loading solution and dissolution media on release of Diclofenac from ion exchange resins

    Directory of Open Access Journals (Sweden)

    "Atyabi F

    2002-07-01

    Full Text Available Drugs can be loaded on ion exchange resins in order to control their release. Loading of diclofenac sodium on the resin beads not only sustain its release but also reduce its gastrointestinal mucosal injury. In this study the effect of loading solution and concentration of diclofenac in loading solution on total amount of drug loaded on the resin beads (Amberlite IRA-900 and the release characteristic of drug in different media were examined. Results showed that diclofenac resin complex did not release their drug content in simulated gastric fluid but released it in simulated intestinal fluid independent of exposure time in acidic conditions. The effect of a number of parameters such as ionic strength and pH on the release characteristic of drug - resin complexes were also examined. Results showed that although ionic strength is an important factor, drug release is more affected by the pH of the media. NO ABSTRACT

  13. Optimum amount of an insurance sum in life insurance

    Directory of Open Access Journals (Sweden)

    Janez Balkovec

    2001-01-01

    Full Text Available Personal insurance represents one of the sources of personal social security as a category of personal property. How to get a proper life insurance is a frequently asked question. When insuring material objects (car, house..., the problem is usually not in the amount of the taken insurance. With life insurance (abstract goods, problems as such occur. In this paper, we wish to present a model that, according to the financial situation and the anticipated future, makes it possible to calculate the optimum insurance sum in life insurance.

  14. [Influence of mastication on the amount of hemoglobin in human brain tissue].

    Science.gov (United States)

    Sasaki, A

    2001-03-01

    The purpose of this study was to investigate the influence of mastication on the amount of hemoglobin in human brain tissue. Nine healthy volunteers (6 males and 3 females) participated in this study. They underwent two tasks: 1) at rest, 2) gum-chewing. In seven of the nine (4 males and 3 females), experimental occlusal interference was applied to the first molar of the mandibule on the habitual masticatory side. They underwent the gum-chewing task. To evaluate the amount of hemoglobin, both the hemoglobin oxygenation state and blood volume during gum-chewing were measured in the frontal region, using near-infrared spectroscopy. The amount of total-hemoglobin (blood volume) and oxyhemoglobin of subjects significantly increased during gum-chewing (p experimental occlusal interference was imposed on the subject, the amount of them significantly decreased compared with subjects without experimental occlusal interference (p < 0.05). The results suggested that increases of cerebral blood flow in the frontal region were not due to the mandibular movement, and that human brain activity caused by mastication was not only in the cortical masticatory area but also in the frontal region.

  15. Blue lighting decreases the amount of food consumed in men, but not in women.

    Science.gov (United States)

    Cho, Sungeun; Han, Ashley; Taylor, Michael H; Huck, Alexandria C; Mishler, Amanda M; Mattal, Kyle L; Barker, Caleb A; Seo, Han-Seok

    2015-02-01

    Previous research has demonstrated that colors of lighting can modulate participants' motivation to consume the food placed under the lighting. This study was designed to determine whether the colors of lighting can affect the amount of food consumed, in addition to sensory perception of the food. The influence of lighting color was also compared between men and women. One-hundred twelve participants (62 men and 50 women) were asked to consume a breakfast meal (omelets and mini-pancakes) under one of three different lighting colors: white, yellow, and blue. During the test, hedonic impression of the food's appearance, willingness to eat, overall flavor intensity and overall impression of the food, and meal size (i.e., the amount of food consumed) were measured. Blue lighting decreased the hedonic impression of the food's appearance, but not the willingness to eat, compared to yellow and white lighting conditions. The blue lighting significantly decreased the amount consumed in men, but not in women, compared to yellow and white lighting conditions. Overall flavor intensity and overall impression of the food were not significantly different among the three lighting colors. In conclusion, this study provides empirical evidence that the color of lighting can modulate the meal size. In particular, blue lighting can decrease the amount of food eaten in men without reducing their acceptability of the food. Published by Elsevier Ltd.

  16. PIXE investigation of in-vitro release of chloramphenicol across polyvinyl alcohol/ acrylamide hydrogel

    International Nuclear Information System (INIS)

    Rihawi, M.; Al-Zeer, A.; Allaf, A.

    2012-01-01

    Hydrogels based on polyvinyl alcohol (PVA) and different amounts of acrylamide monomer (AAm) were prepared by thermal crosslinking process in solid state. The PVA/AAm hydrogels were investigated for drug delivery system applications. Chloramphenicol was adopted as a model drug to study its release behaviour across the prepared hydrogels. Particle induced X-ray emission (PIXE) analytical technique was utilized to study the drug release behaviour across the hydrogels. A comparison study between PIXE and UV measurements was performed. FTIR measurements were carried out to perform the molecular characterization. The releasing behaviour of the drug across the hydrogels demonstrates a decrease and a subsequent increase in the drug release rate, as the AAm amount increases. The FTIR characterization of the prepared hydrogels has shown a competitive behaviour between the crosslinking of PVA with AAm monomer or oligomerized AAm, depending on the amount of AAm added to prepare the PVA/AAm hydrogels. (author)

  17. Estimating the consequences of significant fracture flow at Yucca Mountain

    International Nuclear Information System (INIS)

    Gauthier, J.H.; Wilson, M.L.; Lauffer, F.C.

    1992-01-01

    In this paper a simple model is proposed for investigating the possibility of significant fracture flow at Yucca Mountain, Nevada. The model allows an estimate of the number of flowing fractures at Yucca Mountain based on the size of the fractures and the yearly volume of infiltrating water. Given the number of flowing fractures, the number of waste containers they contact is estimated by a geometric argument. Preliminary results indicate that the larger the flowing fractures, the lower the releases of radionuclides. Also, even with significant fracture flow, releases could be well below the limits set by the Environmental Protection Agency

  18. Estimating the consequences of significant fracture flow at Yucca Mountain

    International Nuclear Information System (INIS)

    Gauthier, J.H.; Wilson, M.L.; Lauffer, F.C.

    1991-01-01

    A simple model is proposed for investigating the possibility of significant fracture flow at Yucca Mountain, Nevada. The model allows an estimate of the number of flowing fractures at Yucca Mountain based on the size of the fractures and the yearly volume of infiltrating water. Given the number of flowing fractures, the number of waste containers they contact is estimated by a geometric argument. Preliminary results indicate that the larger the flowing fractures, the lower the releases of radionuclides. Also, even with significant fracture flow, releases could be well below the limits set by the Environmental Protection Agency

  19. Radioactive release during nuclear accidents in Chernobyl and Fukushima

    Science.gov (United States)

    Nur Ain Sulaiman, Siti; Mohamed, Faizal; Rahim, Ahmad Nabil Ab

    2018-01-01

    Nuclear accidents that occurred in Chernobyl and Fukushima have initiated many research interests to understand the cause and mechanism of radioactive release within reactor compound and to the environment. Common types of radionuclide release are the fission products from the irradiated fuel rod itself. In case of nuclear accident, the focus of monitoring will be mostly on the release of noble gases, I-131 and Cs-137. As these are the only accidents have been rated within International Nuclear Events Scale (INES) Level 7, the radioactive release to the environment was one of the critical insights to be monitored. It was estimated that the release of radioactive material to the atmosphere due to Fukushima accident was approximately 10% of the Chernobyl accident. By referring to the previous reports using computational code systems to model the release rate, the release activity of I-131 and Cs-137 in Chernobyl was significantly higher compare to Fukushima. The simulation code also showed that Chernobyl had higher release rate of both radionuclides on the day of accident. Other factors affecting the radioactive release for Fukushima and Chernobyl accidents such as the current reactor technology and safety measures are also compared for discussion.

  20. The release of nickel from orthodontic NiTi wires is increased by dynamic mechanical loading but not constrained by surface nitridation.

    Science.gov (United States)

    Peitsch, T; Klocke, A; Kahl-Nieke, B; Prymak, O; Epple, M

    2007-09-01

    The influence of dynamic mechanical loading and of surface nitridation on the nickel release from superelastic nickel-titanium orthodontic wires was investigated under ultrapure conditions. Commercially available superelastic NiTi arch wires (size 0.018 x 0.025'') without surface modification (Neo Sentalloy) and with nitrogen ion implantation surface treatment (Neo Sentalloy Ionguard) were analyzed. Mechanical loading of wire segments with a force similar to the physiological situation was performed with a frequency of 5 Hz in ultrapure water and saline solution, respectively. The release of nickel was monitored by atomic absorption spectroscopy for up to 36 days. The mechanically loaded wires released significantly more nickel ( approximately 45 ng cm(-2) d(-1)) than did nonloaded wires (<1 ng cm(-2) d(-1)). There was no statistically significant effect of the testing solution (water or NaCl) or of the surface nitridation. The total amount of released nickel was small in all cases, but may nevertheless account for the occasional clinical observations of adverse reactions during application of NiTi-based orthodontic appliances. The surface nitridation did not constrain the release of nickel from NiTi under continuous mechanical stress.

  1. Release plan for Big Pete

    International Nuclear Information System (INIS)

    Edwards, T.A.

    1996-11-01

    This release plan is to provide instructions for the Radiological Control Technician (RCT) to conduct surveys for the unconditional release of ''Big Pete,'' which was used in the removal of ''Spacers'' from the N-Reactor. Prior to performing surveys on the rear end portion of ''Big Pete,'' it shall be cleaned (i.e., free of oil, grease, caked soil, heavy dust). If no contamination is found, the vehicle may be released with the permission of the area RCT Supervisor. If contamination is found by any of the surveys, contact the cognizant Radiological Engineer for decontamination instructions

  2. The influence of source term release parameters on health effects

    International Nuclear Information System (INIS)

    Jeong, Jong Tae; Ha, Jae Joo

    1998-08-01

    In this study, the influence of source term release parameters on the health effects was examined. This is very useful in identifying the relative importance of release parameters and can be an important factor in developing a strategy for reducing offsite risks. The release parameters investigated in this study are release height, heat content, fuel burnup, release time, release duration, and warning time. The health effects affected by the change of release parameters are early fatalities, cancer fatalities, early injuries, cancer injuries, early fatality risk, population weighted early fatality risk, population weighted cancer fatality risk, effective whole body population dose, population exceeding an early acute red bone marrow dose of 1.5 Sv, and distance at which early fatalities are expected to occur. As release height increases, the values of early health effects such as early fatalities and injuries decrease. However, the release height dose not have significant influences on late health effects. The values of both early and late health effects decrease as heat content increases. The increase fuel burnup, i.e., the increase of core inventories increases the late health effects, however, has small influence on the early health effects. But, the number of early injuries increases as the fuel burnup increases. The effects of release time increase shows very similar influence on both the early and late health effects. As the release time increases to 2 hours, the values of health effects increase and then decrease rapidly. As release duration increases, the values of late health effects increase slightly, however, the values of early health effects decrease. As warning time increases to 2 hours, the values of late health effects decrease and then shows no variation. The number of early injuries decreases rapidly as the warning time increases to 2 hours. However, the number of early fatalities and the early fatality risk increase as the warning time increases

  3. Activated human neutrophils release hepatocyte growth factor/scatter factor.

    LENUS (Irish Health Repository)

    McCourt, M

    2012-02-03

    BACKGROUND: Hepatocyte growth factor or scatter factor (HGF\\/SF) is a pleiotropic cytokine that has potent angiogenic properties. We have previously demonstrated that neutrophils (PMN) are directly angiogenic by releasing vascular endothelial growth factor (VEGF). We hypothesized that the acute inflammatory response can stimulate PMN to release HGF. AIMS: To examine the effects of inflammatory mediators on PMN HGF release and the effect of recombinant human HGF (rhHGF) on PMN adhesion receptor expression and PMN VEGF release. METHODS: In the first experiment, PMN were isolated from healthy volunteers and stimulated with tumour necrosis factor-alpha (TNF-alpha), lipopolysaccharide (LPS), interleukin-8 (IL-8), and formyl methionyl-leucyl-phenylalanine (fMLP). Culture supernatants were assayed for HGF using ELISA. In the second experiment, PMN were lysed to measure total HGF release and HGF expression in the PMN was detected by Western immunoblotting. Finally, PMN were stimulated with rhHGF. PMN CD 11a, CD 11b, and CD 18 receptor expression and VEGF release was measured using flow cytometry and ELISA respectively. RESULTS: TNF-alpha, LPS and fMLP stimulation resulted in significantly increased release of PMN HGF (755+\\/-216, 484+\\/-221 and 565+\\/-278 pg\\/ml, respectively) compared to controls (118+\\/-42 pg\\/ml). IL-8 had no effect. Total HGF release following cell lysis and Western blot suggests that HGF is released from intracellular stores. Recombinant human HGF did not alter PMN adhesion receptor expression and had no effect on PMN VEGF release. CONCLUSIONS: This study demonstrates that pro-inflammatory mediators can stimulate HGF release from a PMN intracellular store and that activated PMN in addition to secreting VEGF have further angiogenic potential by releasing HGF.

  4. Expert system shell to reason on large amounts of data

    Science.gov (United States)

    Giuffrida, Gionanni

    1994-01-01

    The current data base management systems (DBMS's) do not provide a sophisticated environment to develop rule based expert systems applications. Some of the new DBMS's come with some sort of rule mechanism; these are active and deductive database systems. However, both of these are not featured enough to support full implementation based on rules. On the other hand, current expert system shells do not provide any link with external databases. That is, all the data are kept in the system working memory. Such working memory is maintained in main memory. For some applications the reduced size of the available working memory could represent a constraint for the development. Typically these are applications which require reasoning on huge amounts of data. All these data do not fit into the computer main memory. Moreover, in some cases these data can be already available in some database systems and continuously updated while the expert system is running. This paper proposes an architecture which employs knowledge discovering techniques to reduce the amount of data to be stored in the main memory; in this architecture a standard DBMS is coupled with a rule-based language. The data are stored into the DBMS. An interface between the two systems is responsible for inducing knowledge from the set of relations. Such induced knowledge is then transferred to the rule-based language working memory.

  5. Milk intake in kits: not only the total amount matters

    Directory of Open Access Journals (Sweden)

    Alberto Arnau Bonachera

    2017-06-01

    Full Text Available The aim of this work was to identify milk intake variation patterns in kits throughout lactation, to evaluate their permanent maternal component and their relationships with the performance of kits before and after weaning. To achieve this goal, we used 73 rabbit does, controlled between the 1st and the 4th lactation, which kindled 229 litters with a total of 2225 kits. The daily milk intake records per young rabbit were analysed using a principal component analysis (PCA. We found that 72.3% of the variability was explained by the first 3 principal components (PCs. PC1 explained 46.4% of the total variability, was associated with the total amount of milk intake during lactation and presented a repeatability of 0.27 (P0.05. This component was little related to performance traits. Therefore, it seems that milk plays 2 different roles at the beginning of feed intake; the most important would affect development of the kits and thus is related with high intake. The second one, for a given total amount of milk intake during lactation, would create a kind of competition between milk and feed intake at the end of lactation. The effects of both components still persist during the growing period and seem to be moderately affected by the mother.

  6. Release enhancement of tritium from graphite by addition of hydrogen

    International Nuclear Information System (INIS)

    Saeki, Masakatsu; Masaki, N.M.

    1989-01-01

    The release behavior of tritium from graphite was studied in pure He and He + H 2 atmosphere. The release from powdered graphite was significantly enhanced in hydrogen environment. Apparent diffusion coefficients of tritium in graphite also became much higher in an atmosphere containing hydrogen than values obtained in pure helium atmosphere. A careful investigation of the release processes resulted in the conclusion that the most important process of tritium behaviour in graphite was diffusion, but the desorption process of tritium from the surface played a significant role. The enhancement of the desorption process was controlled by atomic hydrogen. (orig.)

  7. Release fraction of PWR after severe accidents. Vol. 4

    International Nuclear Information System (INIS)

    Aziz, M.; El-Messeiry, A.M.

    1996-01-01

    Fission fragments and gases are emitted after accidents as a result of core meltdown and core concrete interactions. These aerosols are transported and fill the reactor containment. With increasing the pressure above pressure design bases, a failure of containment may occur and subsequently these aerosols will release into the external environment leading to a source term of radioactivity that affects the safety of workers and public. The amount of aerosol which escapes to the environment can be described by the release fraction which is defined as the total accumulated aerosol which initially enters the containment. The factors that affect the release fraction is studied, and the aerosol dynamics equation is used to model the release of aerosol to the outside atmosphere. These factors are containment pressure, failure time,break area, the size of aerosol particle. It found that early failure time and higher pressure increase the release fraction, also the release faction is affected by the area and the aerosol particle size. 7 figs., 2 tabs

  8. Effects of compost age on the release of nutrients

    Directory of Open Access Journals (Sweden)

    Bilal B. Al-Bataina

    2016-09-01

    Full Text Available Composted organic materials are applied to help restore disturbed soils, speed revegetation, and control erosion; these changes are generally beneficial for stormwater quality. Ensuring that nutrient release from compost is adequate for plant needs without degrading stormwater quality is important since composts release nitrogen at variable rates (1–3% of total N/yr and the leaching process can extend for many years. The aim of this work was to understand the effect of compost age on the extent and rates of nitrogen release by conducting detailed rainfall simulation studies of one compost type at three different ages. Models describing temporal changes in nitrogen release to runoff during a single storm and across multiple storms were developed and applied to the runoff data. Nitrogen content (% and bulk density of compost increased with the increase in compost age and total nitrogen release decreased with increasing compost age. The three rain simulations (storms performed on each of the three compost ages show that nitrogen release declined each day of the repeated daily storms. A first-order kinetic model was used to estimate the amount of nitrogen remaining on compost after several storms.

  9. Release fraction of PWR after severe accidents. Vol. 4

    Energy Technology Data Exchange (ETDEWEB)

    Aziz, M; El-Messeiry, A M [National Center for Nuclear Safety and Radiation Control, Atomic Energy Authority, Cairo (Egypt)

    1996-03-01

    Fission fragments and gases are emitted after accidents as a result of core meltdown and core concrete interactions. These aerosols are transported and fill the reactor containment. With increasing the pressure above pressure design bases, a failure of containment may occur and subsequently these aerosols will release into the external environment leading to a source term of radioactivity that affects the safety of workers and public. The amount of aerosol which escapes to the environment can be described by the release fraction which is defined as the total accumulated aerosol which initially enters the containment. The factors that affect the release fraction is studied, and the aerosol dynamics equation is used to model the release of aerosol to the outside atmosphere. These factors are containment pressure, failure time,break area, the size of aerosol particle. It found that early failure time and higher pressure increase the release fraction, also the release faction is affected by the area and the aerosol particle size. 7 figs., 2 tabs.

  10. Tritium release experiments with CATS and numerical simulation

    International Nuclear Information System (INIS)

    Munakata, Kenzo; Wajima, Takaaki; Hara, Keisuke; Wada, Kohei; Takeishi, Toshiharu; Shinozaki, Yohei; Mochizuki, Kazuhiro; Katekari, Kenichi; Kobayashi, Kazuhiro; Iwai, Yasunori; Hayashi, Takumi; Yamanishi, Toshihiko

    2010-01-01

    In D-T fusion power plants, large amounts of tritium would be handled. Tritium is the radioisotope of protium, and is easily taken into the human body, and thus the behavior of tritium accidentally released in fusion power plants should be studied for the safety design and radioprotection of workers. Therefore, it is necessary to investigate the behavior of tritium released into large rooms with objectives, since complex flow fields should exist in such rooms and they could influence the ventilation of the air containing released tritium. Thus, tritium release experiments were conducted using Caisson Assembly for Tritium Safety Study (CATS) in TPL/JAEA. Some data were taken for tritium behavior in the ventilated area and response of tritium monitors. In the experiments, approximately 17 GBq of tritium was released into Caisson with the total volume of 12 m 3 , and the room was ventilated at the rate of 12 m 3 /h after release of tritium. It was found that placement of an objective in the vessel substantially affects decontamination efficiency. With regard to an experimental result, numerical calculation was performed and the experimental result and the result of numerical calculation were compared, which indicates that experimental results are qualitatively reproduced by numerical calculation. However, further R and D needs to be carried out for quantitative reproduction of the experimental results.

  11. Tritium release experiments with CATS and numerical simulation

    Energy Technology Data Exchange (ETDEWEB)

    Munakata, Kenzo, E-mail: kenzo@gipc.akita-u.ac.jp [Faculty of Engineering and Resource Sciences, Akita University, Tegata-gakuen-cho 1-1, Akita 010-8502 (Japan); Wajima, Takaaki; Hara, Keisuke; Wada, Kohei [Faculty of Engineering and Resource Sciences, Akita University, Tegata-gakuen-cho 1-1, Akita 010-8502 (Japan); Takeishi, Toshiharu; Shinozaki, Yohei; Mochizuki, Kazuhiro; Katekari, Kenichi [Interdisciplinary Graduate School of Engineering Science, Kyushu University, Hakozaki 6-10-1, Higashi-ku, Fukuoka 812-8581 (Japan); Kobayashi, Kazuhiro; Iwai, Yasunori; Hayashi, Takumi; Yamanishi, Toshihiko [Tritium Technology Group, Japan Atomic Energy Agency, Tokai, Ibaraki 319-1195 (Japan)

    2010-12-15

    In D-T fusion power plants, large amounts of tritium would be handled. Tritium is the radioisotope of protium, and is easily taken into the human body, and thus the behavior of tritium accidentally released in fusion power plants should be studied for the safety design and radioprotection of workers. Therefore, it is necessary to investigate the behavior of tritium released into large rooms with objectives, since complex flow fields should exist in such rooms and they could influence the ventilation of the air containing released tritium. Thus, tritium release experiments were conducted using Caisson Assembly for Tritium Safety Study (CATS) in TPL/JAEA. Some data were taken for tritium behavior in the ventilated area and response of tritium monitors. In the experiments, approximately 17 GBq of tritium was released into Caisson with the total volume of 12 m{sup 3}, and the room was ventilated at the rate of 12 m{sup 3}/h after release of tritium. It was found that placement of an objective in the vessel substantially affects decontamination efficiency. With regard to an experimental result, numerical calculation was performed and the experimental result and the result of numerical calculation were compared, which indicates that experimental results are qualitatively reproduced by numerical calculation. However, further R and D needs to be carried out for quantitative reproduction of the experimental results.

  12. Savannah River Site radioiodine atmospheric releases and offsite maximum doses

    International Nuclear Information System (INIS)

    Marter, W.L.

    1990-01-01

    Radioisotopes of iodine have been released to the atmosphere from the Savannah River Site since 1955. The releases, mostly from the 200-F and 200-H Chemical Separations areas, consist of the isotopes, I-129 and 1-131. Small amounts of 1-131 and 1-133 have also been released from reactor facilities and the Savannah River Laboratory. This reference memorandum was issued to summarize our current knowledge of releases of radioiodines and resultant maximum offsite doses. This memorandum supplements the reference memorandum by providing more detailed supporting technical information. Doses reported in this memorandum from consumption of the milk containing the highest I-131 concentration following the 1961 1-131 release incident are about 1% higher than reported in the reference memorandum. This is the result of using unrounded 1-131 concentrations of I-131 in milk in this memo. It is emphasized here that this technical report does not constitute a dose reconstruction in the same sense as the dose reconstruction effort currently underway at Hanford. This report uses existing published data for radioiodine releases and existing transport and dosimetry models

  13. Uptake and release of glucose by the human kidney. Postabsorptive rates and responses to epinephrine.

    Science.gov (United States)

    Stumvoll, M; Chintalapudi, U; Perriello, G; Welle, S; Gutierrez, O; Gerich, J

    1995-11-01

    Despite ample evidence that the kidney can both produce and use appreciable amounts of glucose, the human kidney is generally regarded as playing a minor role in glucose homeostasis. This view is based on measurements of arteriorenal vein glucose concentrations indicating little or no net release of glucose. However, inferences from net balance measurements do not take into consideration the simultaneous release and uptake of glucose by the kidney. Therefore, to assess the contribution of release and uptake of glucose by the human kidney to overall entry and removal of plasma glucose, we used a combination of balance and isotope techniques to measure renal glucose net balance, fractional extraction, uptake and release as well as overall plasma glucose appearance and disposal in 10 normal volunteers under basal postabsorptive conditions and during a 3-h epinephrine infusion. In the basal postabsorptive state, there was small but significant net output of glucose by the kidney (66 +/- 22 mumol.min-1, P = 0.016). However, since renal glucose fractional extraction averaged 2.9 +/- 0.3%, there was considerable renal glucose uptake (2.3 +/- 0.2 mumol.kg-1.min-1) which accounted for 20.2 +/- 1.7% of systemic glucose disposal (11.4 +/- 0.5 mumol.kg-1.min-1). Renal glucose release (3.2 +/- 0.2 mumol.kg-1.min-1) accounted for 27.8 +/- 2.1% of systemic glucose appearance (11.4 +/- 0.5 mumol.kg-1.min-1). Epinephrine infusion, which increased plasma epinephrine to levels observed during hypoglycemia (3722 +/- 453 pmol/liter) increased renal glucose release nearly twofold (5.2 +/- 0.5 vs 2.8 +/- 0.1 mol.kg-1.min-1, P = 0.01) so that at the end of the infusion, renal glucose release accounted for 40.3 +/- 5.5% of systemic glucose appearance and essentially all of the increase in systemic glucose appearance. These observations suggest an important role for the human kidney in glucose homeostasis.

  14. Novel Nitric Oxide (NO)-Releasing Polymers and Their Biomedical Applications

    Science.gov (United States)

    Brisbois, Elizabeth J.

    Two common factors that can cause complications with indwelling biomedical devices are thrombus and infection. Nitric oxide (NO) is known to be a potent inhibitor of platelet activation and adhesion. Healthy endothelial cells exhibit a NO flux into the bloodstream of 0.5˜4x10-10 mol cm -2 min-1. In addition, NO that is released within the sinus cavities and by neutrophils/macrophages functions as a potent natural antimicrobial agent. Therefore, polymer materials that release NO are expected to have similar anti-thrombotic and antimicrobial properties. In this dissertation work, two novel approaches to achieving long-term NO release from polymers were studied and evaluated for their potential biomedical applications. In the first approach, S-nitroso-N -acetypenicillamine (SNAP)-doped polymers were studied for potential hemocompatibility. The SNAP-doped Elast-eon E2As (block copolymer of poly(dimethylsiloxane) and polyurethane) creates an inexpensive polymer that can locally deliver physiologically relevant levels of NO (via thermal and photochemical reactions). SNAP was also found to be surprisingly stable in the E2As polymer during shelf-life stability and ethylene oxide sterilization studies. The SNAP/E2As polymer was coated on the inner walls of extracorporeal circulation (ECC) circuits and was found to preserve the platelet count at ˜100% of baseline and reduce thrombus area after 4 h blood flow in a rabbit model. The SNAP/E2As polymer was also used to fabricate NO-releasing catheters that were implanted in sheep veins for 7 d. The SNAP/E2As catheters significantly reduced the amount of thrombus and bacterial adhesion (in comparison to E2As control catheters). In the second approach, the NO release from diazeniumdiolated dibutylhexanediamine (DBHD/N2 O 2)-doped polymers was significantly improved using various poly(lactic-co-glycolic acid) (PLGA) additives. Using acid-capped PLGA additives was found to cause high initial bursts of NO, while using an ester

  15. Observation of electrostatically released DNA from gold electrodes with controlled threshold voltages.

    Science.gov (United States)

    Takeishi, Shunsaku; Rant, Ulrich; Fujiwara, Tsuyoshi; Buchholz, Karin; Usuki, Tatsuya; Arinaga, Kenji; Takemoto, Kazuya; Yamaguchi, Yoshitaka; Tornow, Marc; Fujita, Shozo; Abstreiter, Gerhard; Yokoyama, Naoki

    2004-03-22

    DNA oligo-nucleotides, localized at Au metal electrodes in aqueous solution, are found to be released when applying a negative bias voltage to the electrode. The release was confirmed by monitoring the intensity of the fluorescence of cyanine dyes (Cy3) linked to the 5' end of the DNA. The threshold voltage of the release changes depending on the kind of linker added to the DNA 3'-terminal. The amount of released DNA depends on the duration of the voltage pulse. Using this technique, we can retain DNA at Au electrodes or Au needles, and release the desired amount of DNA at a precise location in a target. The results suggest that DNA injection into living cells is possible with this method. (c) 2004 American Institute of Physics

  16. Wound healing effect of bioactive ion released from Mg-smectite.

    Science.gov (United States)

    Sasaki, Yu; Sathi, Gulsan Ara; Yamamoto, Osamu

    2017-08-01

    Bioactive ions like Mg 2+ and Si 4+ have been known as promotion factors of tissue regeneration. In the present work, Mg-smectite, consisting of Mg 2+ and Si 4+ ions, was synthesized by a solution process, and evaluated for the efficiency of the powder on wound healing in rats. White precipitates were obtained by mixing a magnesium chloride hexahydrate solution and a sodium silicate hexahydrate solution at room temperature. The precipitates mixed with a NaOH aqueous solution were subjected to hydrothermal reaction, and finally crystalline Mg-smectite powder was obtained. The crystal and molecular structure of Mg-smectite was identified by X-ray diffractometry (XRD) and Fourier-transform infrared spectroscopy (FT-IR). The synthesized material was determined to be crystalline Mg-smectite. The amount of Mg 2+ and Si 4+ ions released from Mg-smectite in physiological saline was analyzed by inductively coupled plasma mass spectroscopy (ICP-MS). The total amount of Si 4+ ion released from Mg-smectite was greater than that of Mg 2+ ion. To evaluate the wound healing effect of Mg-smectite, Mg-smectite powder was applied to a full-thickness surgical wound reaching the subcutaneous tissue in the rat's abdomen. At 1 and 2weeks, skin tissue was collected and subjected to histological analysis. The results for skin regeneration showed no significant difference in wound size between the control and Mg-smectite group. However, it was found that the neovascularization, collagen deposition, and maturation were notedly accelerated by applying Mg-smectite powder in comparison with the control. Mg-smectite can then be hypothesized to stimulate the regeneration of skin tissue by releasing Mg 2+ and Si 4+ ions. These results suggested that Mg-smectite could offer great potential as a wound dressing material. Copyright © 2017 Elsevier B.V. All rights reserved.

  17. The 2014 water release into the arid Colorado River delta and associated water losses by evaporation

    Energy Technology Data Exchange (ETDEWEB)

    Daesslé, L.W., E-mail: walter@uabc.edu.mx [Instituto de Investigaciones Oceanológicas, Universidad Autónoma de Baja California, CarreteraTranspeninsular Tijuana-Ensenada No. 3917, Fraccionamiento Playitas, CP 22860 Ensenada, Baja California (Mexico); Friedrich-Alexander University of Erlangen-Nuremberg (FAU), Department of Geography and Geosciences, GeoZentrum Nordbayern, Schlossgarten 5, 91054 Erlangen (Germany); Geldern, R. van [Friedrich-Alexander University of Erlangen-Nuremberg (FAU), Department of Geography and Geosciences, GeoZentrum Nordbayern, Schlossgarten 5, 91054 Erlangen (Germany); Orozco-Durán, A. [Instituto de Investigaciones Oceanológicas, Universidad Autónoma de Baja California, CarreteraTranspeninsular Tijuana-Ensenada No. 3917, Fraccionamiento Playitas, CP 22860 Ensenada, Baja California (Mexico); Barth, J.A.C. [Friedrich-Alexander University of Erlangen-Nuremberg (FAU), Department of Geography and Geosciences, GeoZentrum Nordbayern, Schlossgarten 5, 91054 Erlangen (Germany)

    2016-01-15

    For the first time in history, water was intentionally released for environmental purposes into the final, otherwise dry, 160-km stretch of the Colorado River basin, south of the Mexican border. Between March and May 2014 three pulses of water with a total volume of 132 × 10{sup 6} m{sup 3} were released to assess the restoration potential of endemic flora along its course and to reach its estuary. The latter had not received a sustained input of fresh water and nutrients from its main fluvial source for over 50 years because of numerous upstream dam constructions. During this pulse flow large amounts of water were lost and negligible amounts reached the ocean. While some of these water losses can be attributed to plant uptake and infiltration, we were able to quantify evaporation losses between 16.1 to 17.3% of the original water mass % within the first 80 km after the Morels Dam with water stable isotope data. Our results showed no evidence for freshwater reaching the upper Colorado River estuary and it is assumed that the pulse flow had only negligible influences on the coastal ecosystem. Future water releases that aim on ecological restoration need to become more frequent and should have larger volumes if more significant effects are to be established on the area. - Highlights: • Isotope ratios of oxygen and hydrogen quantify water lost through evaporation. • Evaporation losses between 16.1 and 17.3% during the 2014 Colorado River • Larger water volumes are required to influence the estuary ecosystem.

  18. The 2014 water release into the arid Colorado River delta and associated water losses by evaporation

    International Nuclear Information System (INIS)

    Daesslé, L.W.; Geldern, R. van; Orozco-Durán, A.; Barth, J.A.C.

    2016-01-01

    For the first time in history, water was intentionally released for environmental purposes into the final, otherwise dry, 160-km stretch of the Colorado River basin, south of the Mexican border. Between March and May 2014 three pulses of water with a total volume of 132 × 10"6 m"3 were released to assess the restoration potential of endemic flora along its course and to reach its estuary. The latter had not received a sustained input of fresh water and nutrients from its main fluvial source for over 50 years because of numerous upstream dam constructions. During this pulse flow large amounts of water were lost and negligible amounts reached the ocean. While some of these water losses can be attributed to plant uptake and infiltration, we were able to quantify evaporation losses between 16.1 to 17.3% of the original water mass % within the first 80 km after the Morels Dam with water stable isotope data. Our results showed no evidence for freshwater reaching the upper Colorado River estuary and it is assumed that the pulse flow had only negligible influences on the coastal ecosystem. Future water releases that aim on ecological restoration need to become more frequent and should have larger volumes if more significant effects are to be established on the area. - Highlights: • Isotope ratios of oxygen and hydrogen quantify water lost through evaporation. • Evaporation losses between 16.1 and 17.3% during the 2014 Colorado River • Larger water volumes are required to influence the estuary ecosystem.

  19. 51Cr release and oxidative stress in the lens

    International Nuclear Information System (INIS)

    Stewart-DeHaan, P.J.; Sanwal, M.; Creighton, M.O.; Inch, W.R.; Trevithick, J.R.

    1989-01-01

    Examination of the opaque areas of human cortical cataracts has shown that a large portion of the opacity could be attributed to the globules found there. We tested models involving globule formation as a result of oxidative damage to rat lens cells in culture and whole chick embryo lenses. When cell monolayers from a lens cell line were exposed to oxidizing conditions they developed globules on the cell surface. The cells were protected from damage by the addition of glutathione and vitamin C. Thirteen-day chick embryo lenses were also incubated in oxidizing conditions and the amount of cellular damage was assessed using a chromium-51 release assay we have developed. After 24 hr the percent 51Cr in the medium increased by an average of 20% as a result of 10 mM hydrogen peroxide treatment. The addition of the 10 mM vitamin C to the hydrogen peroxide significantly reduced the 51Cr leakage to the control level. Light microscopy of sections of the lens showed a breakdown of the equatorial fibre arrangement in the presence of H2O2, while addition of vitamin C restored the fibre organization to almost normal. The findings suggest that oxidative stress is an important step in cataractogenesis and point towards the use of water soluble antioxidants as protective agents

  20. Gaseous release of radioactive iodine from decaying plants. I. Release following foliar and root uptake

    International Nuclear Information System (INIS)

    Saas, Arsene; Grauby, Andre

    1975-12-01

    Iodine uptake by plants is a significant link in the contamination of the food chain. Long half-live iodine was studied considering foliar and root uptake, loss by rain scavenging, residue decay or outgassing in order to assess two aspects of the problem: the importance of outgassing and the effect of the route of transfer on iodine losses. It appeared that iodine release was a function of the vegetal type, there were differences according to the pattern of absorption (via leaf or root) and the processes of iodine release were usually related to biochemical mechanisms [fr

  1. Radioisotopic composition of yellowcake: an estimation of stack release rates

    International Nuclear Information System (INIS)

    Momeni, M.H.; Kisieleski, W.E.; Rayno, D.R.; Sabau, C.S.

    1979-12-01

    Uranium concentrate (yellowcake) composites from four mills (Anaconda, Kerr-McGee, Highland, and Uravan) were analyzed for U-238, U-235, U-234, Th-230, Ra-226, and Pb-210. The ratio of specific activities of U-238 to U-234 in the composites suggested that secular radioactive equilibrium exists in the ore. The average activity ratios in the yellowcake were determined to be 2.7 x 10 -3 (Th-230/U-238), 5 x 10 -4 (Ra-226/U-238) and 2 x 10 -4 (Pb-210/U-238). Based on earlier EPA measurements of the release rates from the stacks, the amount of yellowcake released was determined to be 0.1% of the amount processed

  2. Sulfur Release during Alternative fuels Combustion in Cement Rotary Kilns

    DEFF Research Database (Denmark)

    Cortada Mut, Maria del Mar

    fuel with the bed material, heating up of a particle, 5 iv devolatilization, char combustion, the reactions between CaSO 4 and the different reducing agents, and the oxidation of the volatiles gases in the free board. The main reducing agents are CO, CH 4 and H 2 , which are introduced under the bed...... are of high importance for SO 2 release because it is shown that introducing the same total amount of gas, the highest reducing agent concentration fo r a short period released a higher total SO 2 amount compared to the lowest concentration during a long period. A mathematical reaction based model...... but the effect of sulfur content in the bed cannot be predicted. Further development regarding particle motion according to the rotational speed may be needed. Furthermore, a model for predicting the tendency of build-ups for a kiln system is developed based on the prediction of SO 3 and Cl concentrations...

  3. Birth control - slow release methods

    Science.gov (United States)

    Contraception - slow-release hormonal methods; Progestin implants; Progestin injections; Skin patch; Vaginal ring ... might want to consider a different birth control method. SKIN PATCH The skin patch is placed on ...

  4. DEVELOPMENT OF SUSTAINED RELEASE TABLETS ...

    African Journals Online (AJOL)

    2013-12-31

    Dec 31, 2013 ... The SR dosage forms that release drugs pH independently in .... were determined; Post compression parameters such as weight variation test, hardness, ... Based on the ICH guidelines 12, the stability studies were carried out ...

  5. Targeted delivery and controlled release of Paclitaxel for the treatment of lung cancer using single-walled carbon nanotubes

    International Nuclear Information System (INIS)

    Yu, Baodan; Tan, Li; Zheng, Runhui; Tan, Huo; Zheng, Lixia

    2016-01-01

    A new type of drug delivery system (DDS) based on single-walled carbon nanotubes (SWNTs) for controlled-release of the anti-cancer drug Paclitaxel (PTX) was constructed in this study. Chitosan (CHI) was non-covalently attached to the SWNTs to improve biocompatibility. Biocompatible hyaluronan was also combined to the outer CHI layer to realise the specific targeting property. The results showed that the release of PTX was pH-triggered and was better at lower pH (pH 5.5). The modified SWNTs showed a significant improvement in intracellular reactive oxygen species (ROS), which may have enhanced mitogen-activated protein kinase activation and further promoted cell apoptosis. The results of western blotting indicated that the apoptosis-related proteins were abundantly expressed in A549 cells. Lactate dehydrogenase (LDH) release assay and cell viability assay demonstrated that PTX-loaded SWNTs could destroy cell membrane integrity, thus inducing lower cell viability of the A549 cells. Thus, this targeting DDS could effectively inhibit cell proliferation and kill A549 cells, is a promising system for cancer therapy. - Highlights: • Chitosan and hyaluronan modified single-walled carbon nanotubes (SWNTs) were prepared for delivery of Paclitaxel (PTX). • Morphology, drug loading efficiency and drug release amount of the nanotubes were studied. • Cell viability, LDH, intracellular ROS levels and western blotting were evaluated. • The drug delivery system could effectively inhibit A549 cells proliferation.

  6. Targeted delivery and controlled release of Paclitaxel for the treatment of lung cancer using single-walled carbon nanotubes

    Energy Technology Data Exchange (ETDEWEB)

    Yu, Baodan; Tan, Li; Zheng, Runhui; Tan, Huo, E-mail: tanhuo.2008@163.com; Zheng, Lixia, E-mail: 66593953@qq.com

    2016-11-01

    A new type of drug delivery system (DDS) based on single-walled carbon nanotubes (SWNTs) for controlled-release of the anti-cancer drug Paclitaxel (PTX) was constructed in this study. Chitosan (CHI) was non-covalently attached to the SWNTs to improve biocompatibility. Biocompatible hyaluronan was also combined to the outer CHI layer to realise the specific targeting property. The results showed that the release of PTX was pH-triggered and was better at lower pH (pH 5.5). The modified SWNTs showed a significant improvement in intracellular reactive oxygen species (ROS), which may have enhanced mitogen-activated protein kinase activation and further promoted cell apoptosis. The results of western blotting indicated that the apoptosis-related proteins were abundantly expressed in A549 cells. Lactate dehydrogenase (LDH) release assay and cell viability assay demonstrated that PTX-loaded SWNTs could destroy cell membrane integrity, thus inducing lower cell viability of the A549 cells. Thus, this targeting DDS could effectively inhibit cell proliferation and kill A549 cells, is a promising system for cancer therapy. - Highlights: • Chitosan and hyaluronan modified single-walled carbon nanotubes (SWNTs) were prepared for delivery of Paclitaxel (PTX). • Morphology, drug loading efficiency and drug release amount of the nanotubes were studied. • Cell viability, LDH, intracellular ROS levels and western blotting were evaluated. • The drug delivery system could effectively inhibit A549 cells proliferation.

  7. Influence of the conditional release of the materials with very low level of radioactivity on the environment - 59132

    International Nuclear Information System (INIS)

    Prvakova, Slavka; Mrskova, Adela; Pritrsky, Jozef

    2012-01-01

    Significant amount of solid materials (metals, non-metals, building structures) that could be contaminated or activated is produced during operation and especially decommissioning of nuclear power plants. Considerable fraction of these materials has level of radioactivity close to the radiological limits allowing its safe release into the environment thereby could be potentially recycled within the special constructions, as for example tunnels, roads or bridges. If the requirements of legislation on the radiological limits for handling such material and long-term safety of the constructions are met, contaminated material can be incorporated in the form of recycled concrete, remelted steel, etc. The paper presents implementation of the IAEA and EC recommendations into the form of detailed analytical approaches with the aim to develop integrated scenarios and to analyse long-term influence of the conditional release of the material with very low level of radioactivity on the environment. Further, an estimation of the key input parameters characteristic for the specific conditions of Slovak case in order to fulfil the radiological limits according to the Slovak legislation is included. Analysed integrated scenarios represent surface or underground civil construction with radionuclides released directly into the geosphere and transported by a groundwater flow to the biosphere. The migration of radionuclides is modelled in the near-surface conditions with the advection as a dominant transport mechanism. Computer code GoldSim is used to evaluate the long-term safety assessment of the conditionally released material on the environment. (authors)

  8. Effects of various catalysts on hydrogen release and uptake characteristics of LiAlH{sub 4}

    Energy Technology Data Exchange (ETDEWEB)

    Resan, Mirna; Hampton, Michael D.; Lomness, Janice K. [Department of Chemistry, University of Central Florida, 4000 Central Florida Boulevard, Orlando, FL 32816-2366 (United States); Slattery, Darlene K. [Florida Solar Energy Center, 1679 Clearlake Rd., Cocoa, FL 32922 (United States)

    2005-11-01

    The effects of various catalysts on the hydrogen release characteristics of LiAlH{sub 4} were studied. The catalysts were incorporated into the alanate by ball milling. The catalysts studied included elemental titanium, TiH{sub 2}, TiCl{sub 4}, TiCl{sub 3}, AlCl{sub 3}, FeCl{sub 3}, elemental iron, elemental nickel, elemental vanadium, and carbon black. Dehydriding/rehydriding properties were characterized by using differential scanning calorimetry coupled with pressure measurement and X-ray diffraction. The addition of TiCl{sub 3} and TiCl{sub 4} to LiAlH{sub 4} eliminated the first step of hydrogen evolution and significantly lowered decomposition temperature of the second step. Doping with elemental iron caused only a slight decrease in the amount of hydrogen released and did not eliminate the first step of hydrogen evolution. Ball milling in the absence of the catalyst was found to decrease the release temperature of hydrogen, while doping with elemental iron did not have any additional effect on the temperature of hydrogen release of LiAlH{sub 4}. (author)

  9. Augmented surgical amounts for intermittent exotropia to prevent recurrence

    Directory of Open Access Journals (Sweden)

    Hatice Arda

    2014-01-01

    Full Text Available Purpose: The purpose was to evaluate the results of bilateral lateral rectus (BLR recession which is based on augmented surgical amounts of classical surgical table of Parks′ for basic and pseudo-divergence excess type intermittent exotropia [X(T]. Materials and Methods: Patients with X(T operated by the same surgeon and followed-up for at least 6 months were included. Patients with prior surgery, neurobehavioral and musculoskeletal conditions, strabismus different from that mentioned above X(T were excluded. All the patients received BLR only. The amount of the recession was increased by the amount needed to correct 5 prism diopters (PD more X(T than what was measured. After the operation, 1 st week, 2 nd and 6 months measurements were recorded. The patients were grouped according to their 1 st week (3-7 days postoperative examination as: >10 PD esotropia (Group 1, ≤10 PD esotropia (Group 2, exotropia (Group 3, and orthotropic (Group 4, respectively. Final surgical outcomes were classified as "good" (≤10 PD exotropia and ≤5 PD esotropia, "recurrence" (>10 PD exotropia and "overcorrected" (>5 esotropia. Results: Thirty-seven patients were included. The mean age was 6.78 ± 2.87 years (range: 2-12 years. Mean preoperative deviation was 29.72 ± 8.07 PD (range: 15-45 PD at distance and 20.94 ± 11.65 PD (range: 10-45 PD at near (P < 0.0001. There were 21 (56.8% patients in Group 1, 9 (24.3% patients in Group 2, 1 (2.7% patient in Group 3 and 6 (16.2% patients in Group 4. Initial esotropia was achieved in 30 (30/37 of the patients. Twenty-eight of them had good results at the end of the 6 months. Overall "motor surgical" success rate was found to be 89.2% (33/37 patients, with 1 (2.7% overcorrection and 3 (8.1% recurrences at the end of the 6 months. Conclusion: This study demonstrated that early overcorrection of 10-20 PD after X(T surgery can achieve acceptable motor outcomes in the first 6 months postoperative period.

  10. Localised controlled release of simvastatin from porous chitosan–gelatin scaffolds engrafted with simvastatin loaded PLGA-microparticles for bone tissue engineering application

    Energy Technology Data Exchange (ETDEWEB)

    Gentile, Piergiorgio [Department of Mechanical and Aerospace Engineering, Politecnico di Torino, Corso Duca degli Abruzzi 24, 10129 Turin (Italy); School of Clinical Dentistry, University of Sheffield, 19 Claremont Crescent, Sheffield (United Kingdom); Nandagiri, Vijay Kumar [Department of Mechanical and Aerospace Engineering, Politecnico di Torino, Corso Duca degli Abruzzi 24, 10129 Turin (Italy); School of Pharmacy, Royal College of Surgeons in Ireland, 123, St. Stephen Green, Dublin 2 (Ireland); Daly, Jacqueline [Division of Biology, Department of Anatomy, Royal College of Surgeons in Ireland, 123, St. Stephen Green, Dublin 2 (Ireland); Chiono, Valeria; Mattu, Clara; Tonda-Turo, Chiara; Ciardelli, Gianluca [Department of Mechanical and Aerospace Engineering, Politecnico di Torino, Corso Duca degli Abruzzi 24, 10129 Turin (Italy); Ramtoola, Zebunnissa, E-mail: zramtoola@rcsi.ie [School of Pharmacy, Royal College of Surgeons in Ireland, 123, St. Stephen Green, Dublin 2 (Ireland)

    2016-02-01

    Localised controlled release of simvastatin from porous freeze-dried chitosan–gelatin (CH–G) scaffolds was investigated by incorporating simvastatin loaded poly-(DL-lactide-co-glycolide) acid (PLGA) microparticles (MSIMs) into the scaffolds. MSIMs at 10% w/w simvastatin loading were prepared using a single emulsion-solvent evaporation method. The MSIM optimal amount to be incorporated into the scaffolds was selected by analysing the effect of embedding increasing amounts of blank PLGA microparticles (BL-MPs) on the scaffold physical properties and on the in vitro cell viability using a clonal human osteoblastic cell line (hFOB). Increasing the BL-MP content from 0% to 33.3% w/w showed a significant decrease in swelling degree (from 1245 ± 56% to 570 ± 35%). Scaffold pore size and distribution changed significantly as a function of BL-MP loading. Compressive modulus of scaffolds increased with increasing BL-MP amount up to 16.6% w/w (23.0 ± 1.0 kPa). No significant difference in cell viability was observed with increasing BL-MP loading. Based on these results, a content of 16.6% w/w MSIM particles was incorporated successfully in CH–G scaffolds, showing a controlled localised release of simvastatin able to influence the hFOB cell proliferation and the osteoblastic differentiation after 11 days. - Highlights: • Simvastatin loaded PLGA microparticle engrafted porous CH–G scaffolds were produced. • The microparticle optimal amount to be incorporated into the scaffolds was studied. • Physical properties of scaffolds changed as a function of microparticle loading. • The level of simvastatin released enhanced cell proliferation and mineralisation.

  11. Localised controlled release of simvastatin from porous chitosan–gelatin scaffolds engrafted with simvastatin loaded PLGA-microparticles for bone tissue engineering application

    International Nuclear Information System (INIS)

    Gentile, Piergiorgio; Nandagiri, Vijay Kumar; Daly, Jacqueline; Chiono, Valeria; Mattu, Clara; Tonda-Turo, Chiara; Ciardelli, Gianluca; Ramtoola, Zebunnissa

    2016-01-01

    Localised controlled release of simvastatin from porous freeze-dried chitosan–gelatin (CH–G) scaffolds was investigated by incorporating simvastatin loaded poly-(DL-lactide-co-glycolide) acid (PLGA) microparticles (MSIMs) into the scaffolds. MSIMs at 10% w/w simvastatin loading were prepared using a single emulsion-solvent evaporation method. The MSIM optimal amount to be incorporated into the scaffolds was selected by analysing the effect of embedding increasing amounts of blank PLGA microparticles (BL-MPs) on the scaffold physical properties and on the in vitro cell viability using a clonal human osteoblastic cell line (hFOB). Increasing the BL-MP content from 0% to 33.3% w/w showed a significant decrease in swelling degree (from 1245 ± 56% to 570 ± 35%). Scaffold pore size and distribution changed significantly as a function of BL-MP loading. Compressive modulus of scaffolds increased with increasing BL-MP amount up to 16.6% w/w (23.0 ± 1.0 kPa). No significant difference in cell viability was observed with increasing BL-MP loading. Based on these results, a content of 16.6% w/w MSIM particles was incorporated successfully in CH–G scaffolds, showing a controlled localised release of simvastatin able to influence the hFOB cell proliferation and the osteoblastic differentiation after 11 days. - Highlights: • Simvastatin loaded PLGA microparticle engrafted porous CH–G scaffolds were produced. • The microparticle optimal amount to be incorporated into the scaffolds was studied. • Physical properties of scaffolds changed as a function of microparticle loading. • The level of simvastatin released enhanced cell proliferation and mineralisation.

  12. PCDD/PCDF release inventories

    Energy Technology Data Exchange (ETDEWEB)

    Fiedler, H. [UNEP Chemicals, Chatelaine (Switzerland)

    2004-09-15

    The Stockholm Convention on Persistent Organic Pollutants (POPs) entered into force on 17 May 2004 with 50 Parties. In May 2004, 59 countries had ratified or acceded the Convention. The objective of the Convention is ''to protect human health and the environment from persistent organic pollutants''. For intentionally produced POPs, e.g., pesticides and industrial chemicals such as hexachlorobenzene and polychlorinated biphenyls, this will be achieved by stop of production and use. For unintentionally generated POPs, such as polychlorinated dibenzo-pdioxins (PCDD) and polychlorinated dibenzofurans (PCDF), measures have to be taken to ''reduce the total releases derived from anthropogenic sources''; the final goal is ultimate elimination, where feasible. Under the Convention, Parties have to establish and maintain release inventories to prove the continuous release reduction. Since many countries do not have the technical and financial capacity to measure all releases from all potential PCDD/PCDF sources, UNEP Chemicals has developed the ''Standardized Toolkit for the Identification of Quantification of Dioxin and Furan Releases'' (''Toolkit'' for short), a methodology to estimate annual releases from a number of sources. With this methodology, annual releases can be estimated by multiplying process-specific default emission factors provided in the Toolkit with national activity data. At the seventh session of the Intergovernmental Negotiating Committee, the Toolkit was recommended to be used by countries when reporting national release data to the Conference of the Parties. The Toolkit is especially used by developing countries and countries with economies in transition where no measured data are available. Results from Uruguay, Thailand, Jordan, Philippines, and Brunei Darussalam have been published.

  13. Officially released mutant varieties in China

    International Nuclear Information System (INIS)

    Liu, L.; Van Zanten, L.; Shu, Q.Y.; Maluszynski, M.

    2004-01-01

    The use of mutation techniques for crop improvement in China has a long and well-established tradition of more than 50 years. As the result of intensive research in many institutes dealing with application of nuclear technologies more than 620 cultivars of 44 crop species have been released. Numerous mutant varieties have been grown on a large scale bringing significant economic impact, sustaining crop production and greatly contributing to increase of food production also in stress prone areas of the country. However, there is still missing information not only on the number of mutant varieties released in particular crop species but also on mutagens applied, selection approaches and on the use of mutants in cross breeding. Numerous Chinese scientists collected and systematized this information. Results of their work were often published in local scientific journals in the Chinese language and as such were unavailable to breeders from other countries. Having this in mind, we requested Dr. Liu Luxiang, the Director of the Department of Plant Mutation Breeding and Genetics, Institute for Application of Atomic Energy, Chinese Academy of Agricultural Sciences in Beijing to help us in finding as much information as possible on mutant varieties officially released in China. The data has been collected in close collaboration with his colleagues from various institutions all over the country and then evaluated, edited and prepared for publication by our team responsible for the FAO/IAEA Database of Officially Released Mutant Varieties. We would like to thank all Chinese colleagues who contributed to this list of Chinese mutant varieties. We hope that this publication will stimulate plant breeders in China to collect more information on released mutant varieties and especially on the use of mutated genes in cross breeding. (author)

  14. Sodium lauryl sulfate impedes drug release from zinc-crosslinked alginate beads: switching from enteric coating release into biphasic profiles.

    Science.gov (United States)

    Taha, Mutasem O; Nasser, Wissam; Ardakani, Adel; Alkhatib, Hatim S

    2008-02-28

    The aim of this research is to investigate the effects of sodium lauryl sulfate (SLS) on ionotropically cross-linked alginate beads. Different levels of SLS were mixed with sodium alginate and chlorpheniramine maleate (as loaded model drug). The resulting viscous solutions were dropped onto aqueous solutions of zinc or calcium ions for ionotropic curing. The generated beads were assessed by their drug releasing profiles, infrared and differential scanning colorimetery (DSC) traits. SLS was found to exert profound concentration-dependent impacts on the characteristics of zinc-crosslinked alginate beads such that moderate modifications in the levels of SLS switched drug release from enteric coating-like behavior to a biphasic release modifiable to sustained-release by the addition of minute amounts of xanthan gum. Calcium cross-linking failed to reproduce the same behavior, probably due to the mainly ionic nature of calcium-carboxylate bonds compared to the coordinate character of their zinc-carboxylate counterparts. Apparently, moderate levels of SLS repel water penetration into the beads, and therefore minimize chlorpheniramine release. However, higher SLS levels seem to discourage polymeric cross-linking and therefore allow biphasic drug release.

  15. Amount of prenatal visual stimulation alters incubation times and postnatal preferences in leopard geckos (Eublepharis macularius).

    Science.gov (United States)

    Sleigh, M J; Birchard, G F

    2001-09-01

    The authors exposed gecko (Eublepharis macularius) embryos to patterned visual stimulation beginning at either 1 week or 2 weeks prior to hatching. Embryos exposed to the substantially augmented amount of prenatal visual stimulation hatched significantly earlier than the embryos either exposed to the moderately augmented prenatal visual stimulation or not exposed to any prenatal visual stimulation (p geckos in all conditions failed to exhibit a preference for either stimulus.

  16. [Effects of irrigation amount on morphological characteristics and water use of Jatropha curcas].

    Science.gov (United States)

    Yang, Qi-Liang; Zhang, Jing; Liu, Xiao-Gang; Liu, Yan-Wei; Yang, Ju-Rui

    2014-05-01

    Jatropha curcas is the most promising energy tree, and soil moisture is the key factor which affects the seedling quality and water use efficiency of J. curcas. With aims to evaluate the effect of different irrigation amount on growth, morphological characteristics and water use of J. curcas, a pot experiment was conducted with four irrigation amounts, i. e., W1:472.49 mm, W2: 228.79 mm, W3:154.18 mm and W4:106.93 mm, respectively. Compared with W1 treatment, the leaf area and stem cross-section area of base significantly decreased in W2, W3 and W4 treatments, but Huber value significantly increased, which could improve the efficiency of water transfer from root to shoot, thus enhance the capability of resistance to drought stress. Compared with W, treatment, the healthy index of J. curcas seedlings decreased slightly in W2 treatment but significantly decreased in W3 and W4 treatments. Hence, the irrigation amount from 228.79 to 472.49 mm was beneficial to increase the healthy index of J. curcas seedlings. Compared with W1 treatment, irrigation water was saved by 67.4% in W3 treatment, and the total dry mass and evapotranspiration significantly decreased by 17.4% and 68.6%, and the irrigation water use efficiency and total water use efficiency increased by 153.2% and 163.2%, respectively. In the condition of this study, the irrigation amount of 154.18 mm was beneficial to increase water use efficiency.

  17. Quantitative relationship between adsorbed amount of solute and solvent composition

    International Nuclear Information System (INIS)

    Wang Yan; Geng Xindu; Zebolsky, Don M.

    2003-01-01

    A new adsorption isotherm that relates the amount of solute adsorbed to the solvent concentration is proposed. The new equation is derived from Geng and Shi's stoichiometric displacement model for adsorption (SDM-A). The obtained equation may be simplified to an expression containing two parameters. The equation with two parameters, valid for low concentrations of solute, is a logarithmically linear relationship. The intercept contains a thermodynamic equilibrium constant of the solute displacing solvent from the adsorbent. The slope is the negative value of the stoichiometric displacement parameter (Z), the average total number of solvent molecules displaced from an active site on the adsorbent and from the solute. Tests with a homologous series of aromatic alcohols by frontal analysis in reversed phase liquid chromatography demonstrate that experimental results fit the equation well

  18. Late excretion of plutonium following acquisition of known amounts

    International Nuclear Information System (INIS)

    Rundo, J.

    1981-01-01

    The urinary and fecal excretion rates of plutonium 10,000 days after intravenous injection of known amounts are compared with the predictions of various models. Both Langham's and Durbin's equations underestimated the urinary excretion by about an order of magnitude; the observed fecal excretion rates were also higher than the predictions. The total excretion rate predicted by the ICRP model was in quite good agreement with the observed rate, but it overestimated it at early times ( 239 Pu of former Manhattan Project plutonium workers, as calculated from the measured urinary excretion an application of Langham's equation. In one of these subjects the urinary excretion rate started to increase at about 6000 days, reached a maximum at about 9500 days, and declined for the next 2700 days

  19. Determination of micro amounts of praseodymium by analogue derivative spectrophotometry

    International Nuclear Information System (INIS)

    Ishii, Hajime; Satoh, Katsuhiko.

    1986-01-01

    Derivative spectrophotometry using the analogue differentiation circuit was applied to the determination of praseodymium at the ppm level. By the proposed method, in which the second or fourth derivative spectrum of the characteristic absorption band of praseodymium(III) at 444 nm is measured, as little as 3 ppm of praseodymium can be determined directly and easily even in the presence of large amounts of other rare earths without any prior separation. Interferences from neodymium, samarium, dysprosium, holmium and erbium ions which have characteristic absorption bands around 444 nm can easily be removed by utilizing the isosbestic point in the derivative spectra of praseodymium(III) and the interfering rare earth(III). (author)

  20. Does the amount of school choice matter for student engagement?

    Science.gov (United States)

    Vaughn, Michael G.; Witko, Christopher

    2013-01-01

    School choice may increase student engagement by enabling students to attend schools that more closely match their needs and preferences. But this effect on engagement may depend on the characteristics of the choices available. Therefore, we consider how the amount of educational choice of different types in a local educational marketplace affects student engagement using a large, national population of 8th grade students. We find that more choice of regular public schools in the elementary and middle school years is associated with a lower likelihood that students will be severely disengaged in eighth grade, and more choices of public schools of choice has a similar effect but only in urban areas. In contrast, more private sector choice does not have such a general beneficial effect. PMID:23682202

  1. Discovering Related Clinical Concepts Using Large Amounts of Clinical Notes.

    Science.gov (United States)

    Ganesan, Kavita; Lloyd, Shane; Sarkar, Vikren

    2016-01-01

    The ability to find highly related clinical concepts is essential for many applications such as for hypothesis generation, query expansion for medical literature search, search results filtering, ICD-10 code filtering and many other applications. While manually constructed medical terminologies such as SNOMED CT can surface certain related concepts, these terminologies are inadequate as they depend on expertise of several subject matter experts making the terminology curation process open to geographic and language bias. In addition, these terminologies also provide no quantifiable evidence on how related the concepts are. In this work, we explore an unsupervised graphical approach to mine related concepts by leveraging the volume within large amounts of clinical notes. Our evaluation shows that we are able to use a data driven approach to discovering highly related concepts for various search terms including medications, symptoms and diseases.

  2. Discovering Related Clinical Concepts Using Large Amounts of Clinical Notes

    Directory of Open Access Journals (Sweden)

    Kavita Ganesan

    2016-01-01

    Full Text Available The ability to find highly related clinical concepts is essential for many applications such as for hypothesis generation, query expansion for medical literature search, search results filtering, ICD-10 code filtering and many other applications. While manually constructed medical terminologies such as SNOMED CT can surface certain related concepts, these terminologies are inadequate as they depend on expertise of several subject matter experts making the terminology curation process open to geographic and language bias. In addition, these terminologies also provide no quantifiable evidence on how related the concepts are. In this work, we explore an unsupervised graphical approach to mine related concepts by leveraging the volume within large amounts of clinical notes. Our evaluation shows that we are able to use a data driven approach to discovering highly related concepts for various search terms including medications, symptoms and diseases.

  3. Kinetic Spectrophotometric Determination of Trace Amounts of Sulfide

    Energy Technology Data Exchange (ETDEWEB)

    Barzegar, Mohsen [Tarbiat Modarres University, Tehran (Iran, Islamic Republic of); Jabbari, Ali [K. N. Toosi University, Tehran (Iran, Islamic Republic of); Esmaeili, Majid [Razi University, Kermanshah (Iran, Islamic Republic of)

    2003-09-15

    A method for the determination of trace amount of sulfide based on the addition reaction of sulfide with methyl green at pH 7.5 and 25 .deg. C is described. The reaction is monitored spectrophotometrically by measuring the decrease in absorbance of the dyestuff at 637 nm by the initial rate and fixed time method. The calibration graph is linear in the range 30-1200 ppb. The theoretical limit of detection was 0.014 ppm. Seven replicate analysis of a sample solution containing 0.70 ppm sulfide gave a relative standard deviation of 1.5%. The interfering effects of various ions on sulfide determination have been reported and procedures for removal of interference have been described. The proposed method was applied successfully to the determination of sulfide in tap and wastewater samples.

  4. Kinetic Spectrophotometric Determination of Trace Amounts of Sulfide

    International Nuclear Information System (INIS)

    Barzegar, Mohsen; Jabbari, Ali; Esmaeili, Majid

    2003-01-01

    A method for the determination of trace amount of sulfide based on the addition reaction of sulfide with methyl green at pH 7.5 and 25 .deg. C is described. The reaction is monitored spectrophotometrically by measuring the decrease in absorbance of the dyestuff at 637 nm by the initial rate and fixed time method. The calibration graph is linear in the range 30-1200 ppb. The theoretical limit of detection was 0.014 ppm. Seven replicate analysis of a sample solution containing 0.70 ppm sulfide gave a relative standard deviation of 1.5%. The interfering effects of various ions on sulfide determination have been reported and procedures for removal of interference have been described. The proposed method was applied successfully to the determination of sulfide in tap and wastewater samples

  5. First-aid training in school: amount, content and hindrances.

    Science.gov (United States)

    Bakke, H K; Bakke, H K; Schwebs, R

    2017-11-01

    To increase knowledge and competence about first aid in the population, first-aid instruction is included in primary and secondary school curricula. This study aimed to establish how much time is spent on first-aid training, which first-aid measures are taught, and which factors prevent teachers from providing the quantity and quality of first-aid training that they wish to give. A questionnaire was distributed to teachers in physical education in primary and secondary schools and to teachers in vocational subjects in higher secondary schools. The teachers taught a median of two lessons in first aid per year. Cardiopulmonary resuscitation (CPR) was taught by 64% of teachers, free airway and recovery position by 69% and stopping severe bleeding by 51%. Recognising heart attack and stroke was taught by 25% and 23%, respectively. The main factors that the teachers perceived as limiting the amount and quality of first-aid training were insufficient learning objective specifications in the curriculum, too many other competence aims, lack of CPR mannequins and lack of training as first-aid instructors. Norwegian teachers provide an appreciable amount of first-aid training to their students. However, several potential life-saving measures are poorly covered. The curriculum needs to contain first aid but also should specify what first-aid measures to be taught. First-aid training of teachers should adequately prepare them to be first-aid instructors. © 2017 The Authors. Acta Anaesthesiologica Scandinavica published by John Wiley & Sons Ltd on behalf of Acta Anaesthesiologica Scandinavica Foundation.

  6. Knowledge discovery: Extracting usable information from large amounts of data

    International Nuclear Information System (INIS)

    Whiteson, R.

    1998-01-01

    The threat of nuclear weapons proliferation is a problem of world wide concern. Safeguards are the key to nuclear nonproliferation and data is the key to safeguards. The safeguards community has access to a huge and steadily growing volume of data. The advantages of this data rich environment are obvious, there is a great deal of information which can be utilized. The challenge is to effectively apply proven and developing technologies to find and extract usable information from that data. That information must then be assessed and evaluated to produce the knowledge needed for crucial decision making. Efficient and effective analysis of safeguards data will depend on utilizing technologies to interpret the large, heterogeneous data sets that are available from diverse sources. With an order-of-magnitude increase in the amount of data from a wide variety of technical, textual, and historical sources there is a vital need to apply advanced computer technologies to support all-source analysis. There are techniques of data warehousing, data mining, and data analysis that can provide analysts with tools that will expedite their extracting useable information from the huge amounts of data to which they have access. Computerized tools can aid analysts by integrating heterogeneous data, evaluating diverse data streams, automating retrieval of database information, prioritizing inputs, reconciling conflicting data, doing preliminary interpretations, discovering patterns or trends in data, and automating some of the simpler prescreening tasks that are time consuming and tedious. Thus knowledge discovery technologies can provide a foundation of support for the analyst. Rather than spending time sifting through often irrelevant information, analysts could use their specialized skills in a focused, productive fashion. This would allow them to make their analytical judgments with more confidence and spend more of their time doing what they do best

  7. Iron isotope constraints on arsenic release from Mekong Delta sediments, Cambodia

    Science.gov (United States)

    Matsumoto, T.; Yamaguchi, K. E.; Hirata, T.; Yamagata, Y.; Yamaguchi, A.; Abe, G.

    2017-12-01

    Arsenic-contaminated groundwater is a world-wide environmental problem and threatens more than 100 million people living in delta areas of South, SE and East Asia. It is typically associated with reducing aquifers with organic-rich alluvial sediments, little thermal gradients, low sulfate concentrations, and slow flushing rates. Such conditions are typical for low-lying countries in Asian deltas; however, compared to Bangladesh, Cambodia has received far less attention. Upon reductive dissolution of Fe-(oxyhydr)oxides that adsorbed As, Fe and As are released into solution as dissolved Fe2+ and arsenate, respectively. Following the oxidation of dissolved Fe2+, newly-formed Fe-(oxyhydr)oxides adsorb As again. Thus, in anoxic waters, concentrations of As correlate with those of dissolved Fe2+. Fluctuating redox conditions in the aquifer are control As release, although inhibition of adsorption of arsenate and arsenite onto the Fe-(oxyhydr)oxides occurs when the concentrations of phosphate, bicarbonate, silicate, and/or organic matter become sufficiently high. Biogeochemical redox reactions of Fe result in significant isotope fractionation (e.g., Johnson et al., 2008). We hypothesized that magnitude of isotope fractionation of Fe in the aquifer sediments, reflecting repeated (incomplete) redox reactions of Fe, may be proportional to the amount of total As release. We aim to calibrate the As release from aquifer sediment by Fe isotope analysis. As a preliminary study, series of sediment samples were collected from the Mekong Delta, Cambodia, in September 2016. Based on measurements by XRF, ICP-AES and ICP-MS, concentrations of As varied significantly covering the range from 4.5 to 15.5 µg/g with a median value of 11 µg/g (higher than the average crustal value of 5 µg/g), and those of Fe is from 2.6 to 9.7 wt.% with a median value of 7.1 wt.%. Concentrations of As and Fe show positive correlation (R2 = 0.72), indicating an effective redox cycling of Fe and As as

  8. Effect of interfacial composition and crumbliness on aroma release in soy protein/sugar beet pectin mixed emulsion gels.

    Science.gov (United States)

    Hou, Jun-Jie; Guo, Jian; Wang, Jin-Mei; Yang, Xiao-Quan

    2016-10-01

    In this study, soy protein isolate/sugar beet pectin (SPI/SBP) emulsion gels were prepared through an enzymatic gelation process. The effects of emulsifier (SBP, SPI or SPI/SBP complex) and emulsification process on the microstructure, texture, breakdown properties and aroma release behavior of resulting emulsion gels were investigated. Oil emulsification by SBP/SPI complex resulted in a higher amount of emulsifier absorbing on the oil-water interface than by SBP and SPI alone, indicating that a more compact interfacial network was formed. Flocculation of oil droplets was observed and corresponding emulsion gels exhibited lower fracture force and strain when the oil was emulsified by SPI and SBP/SPI complex. Moreover, emulsion gels with small droplets produced a greater quantity of small fragments after mastication. However, microstructure did not have a significant effect on breakdown properties of emulsion gels. Headspace gas chromatography analysis showed that the release rate of ethyl butyrate before and after mastication was significantly lower in emulsion gel with more compact network, but the release of aroma compounds with higher hydrophobicity did not show a significant influence of the microstructure and texture of emulsion gel. This finding provides a useful application for designing semi-solid foods with desirable flavor perception. © 2016 Society of Chemical Industry. © 2016 Society of Chemical Industry.

  9. Release of chlorine from biomass at gasification conditions

    Energy Technology Data Exchange (ETDEWEB)

    Bjoerkman, E.; Stroemberg, B. [TPS Termiska Processer AB, Nykoeping (Sweden)

    1997-05-01

    The objective of the project was to investigate the influence of different gasifying atmospheres on the release of chlorine from biomass during gasification conditions. Furthermore, the purpose was also to try and identify the formed chloro compounds. The results showed that O{sub 2}, H{sub 2}O and CO{sub 2} had negligible effect on the chlorine release at temperatures under 700 deg C. At temperatures above 800 deg C the reactivity towards CO{sub 2} increased and could be seen as higher chlorine release and less solid residue. No chloro organic compounds (aliphatic one to six carbons or aromatic one to two rings) could be detected in the tar or the fuel gas produced during pyrolysis/gasifying. On the other hand, comparable amounts of chlorinated benzenes were found in the cooling section during combustion of lucerne and of synthetic waste, indicating that oxygen is essential for chlorination reactions. 11 refs, 4 figs, 1 tab

  10. Release of chlorine from biomass at gasification conditions

    International Nuclear Information System (INIS)

    Bjoerkman, E.; Stroemberg, B.

    1997-05-01

    The objective of the project was to investigate the influence of different gasifying atmospheres on the release of chlorine from biomass during gasification conditions. Furthermore, the purpose was also to try and identify the formed chloro compounds. The results showed that O 2 , H 2 O and CO 2 had negligible effect on the chlorine release at temperatures under 700 deg C. At temperatures above 800 deg C the reactivity towards CO 2 increased and could be seen as higher chlorine release and less solid residue. No chloro organic compounds (aliphatic one to six carbons or aromatic one to two rings) could be detected in the tar or the fuel gas produced during pyrolysis/gasifying. On the other hand, comparable amounts of chlorinated benzenes were found in the cooling section during combustion of lucerne and of synthetic waste, indicating that oxygen is essential for chlorination reactions. 11 refs, 4 figs, 1 tab

  11. Reporting releases of hazardous substances under CERCLA and EPCRA

    International Nuclear Information System (INIS)

    Dailey, R.

    1990-04-01

    Several federal environmental laws requires that ''release of hazardous substances to the environment'' above certain threshold amounts -- Reportable Quantities or RQs -- be reported. Current and proposed regulations under these statutes are unclear and make full compliance difficult. Nevertheless, failure to comply could result in civil or criminal penalties. In response to questions raised by several DOE Field Elements, this Information Brief is part of a series that will provide updated information on this and other CERCLA issues. The Environmental Guidance Division (EH-231) has responded to those questions relating the reporting of releases for which EPA has a clearly articulated position. EPA's position on other questions raised by Field Elements has been equivocal; DOE is working with EPA to resolve these outstanding issues. Additional information briefs on reporting releases will be issued as a clear position is defined

  12. Post-release monitoring of Antillean manatees: an assessment of the Brazilian rehabilitation and release programme

    Science.gov (United States)

    Normande, Iran C.; Malhado, Ana C. M.; Reid, James P.; Viana Junior, P.C.; Savaget, P. V. S.; Correia, R. A.; Luna, F. O.; R. J. Ladle,

    2016-01-01

    Mammalian reintroduction programmes frequently aim to reconnect isolated sub-populations and restore population viability. However, these long-term objectives are rarely evaluated due to the inadequacy of post-release monitoring. Here, we report the results of a unique long term telemetry-based monitoring programme for rehabilitated Antillean manatees (Trichechus manatus manatus) reintroduced into selected sites in northeast Brazil with the aim of reconnecting isolated relict populations. Twenty-one satellite-tagged rehabilitated manatees, 13 males and 8 females, were released into the wild from two sites between November 2008 and June 2013. Individual accumulation curves were plotted and home ranges were calculated through the fixed kernel method using 95% of the utilization distribution. The number and size of the Centres of Activity (COAs) were calculated using 50% of the utilization distribution. Manatees displayed a dichotomous pattern of movement, with individuals either characterized by sedentary habits or by much more extensive movements. Moreover, home range size was not significantly influenced by gender, age at release or release site. COAs were strongly associated with sheltered conditions within reefs and estuaries, and also by the presence of freshwater and feeding sites. Our data confirm that manatee reintroductions in Brazil have the potential to reconnect distant sub-populations. However, pre-release identification of potential long-distance migrants is currently unfeasible, and further analysis would be required to confirm genetic mixing of distant sub-populations.

  13. Fundamental Study of Disposition and Release of Methane in a Shale Gas Reservoir

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Yifeng [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Dept. of Nuclear Waste Disposal Research and Analysis; Xiong, Yongliang [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Dept. of Repository Performance; Criscenti, Louise J. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Dept. of Geochemistry; Ho, Tuan Ahn [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Dept. of Geochemistry; Weck, Philippe F. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Storage and Transportation Technology; Ilgen, Anastasia G. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Dept. of Geochemistry; Matteo, Edward [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Dept. of Nuclear Waste Disposal Research and Analysis; Kruichak, Jessica N. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Dept. of Nuclear Waste Disposal Research and Analysis; Mills, Melissa M. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Dept. of Nuclear Waste Disposal Research and Analysis; Dewers, Thomas [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Dept. of Geomechanics; Gordon, Margaret E. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Dept. of Materials, Devices and Energy Technologies; Akkutlu, Yucel [Texas A & M Univ., College Station, TX (United States). Dept. of Petroleum Engineering

    2016-09-01

    The recent boom in shale gas production through hydrofracturing has reshaped the energy production landscape in the United States. Wellbore production rates vary greatly among the wells within a single field and decline rapidly with time, thus bring up a serious concern with the sustainability of shale gas production. Shale gas production starts with creating a fracture network by injecting a pressurized fluid in a wellbore. The induced fractures are then held open by proppant particles. During production, gas releases from the mudstone matrix, migrates to nearby fractures, and ultimately reaches a production wellbore. Given the relatively high permeability of the induced fractures, gas release and migration in low-permeability shale matrix is likely to be a limiting step for long-term wellbore production. Therefore, a clear understanding of the underlying mechanisms of methane disposition and release in shale matrix is crucial for the development of new technologies to maximize gas production and recovery. Shale is a natural nanocomposite material with distinct characteristics of nanometer-scale pore sizes, extremely low permeability, high clay contents, significant amounts of organic carbon, and large spatial heterogeneities. Our work has shown that nanopore confinement plays an important role in methane disposition and release in shale matrix. Using molecular simulations, we show that methane release in nanoporous kerogen matrix is characterized by fast release of pressurized free gas (accounting for ~ 30 - 47% recovery) followed by slow release of adsorbed gas as the gas pressure decreases. The first stage is driven by the gas pressure gradient while the second stage is controlled by gas desorption and diffusion. The long-term production decline appears controlled by the second stage of gas release. We further show that diffusion of all methane in nanoporous kerogen behaves differently from the bulk phase, with much smaller diffusion coefficients. The MD

  14. Assessment of released organics from leaf biomass on air quality in the state of California

    International Nuclear Information System (INIS)

    Badgett-West, C.R.; Cort, R.P.

    1991-01-01

    Air quality scientists today are concerned that significant amounts of volatile organic compounds (VOCs), specifically isoprenes and monoterpenes, are released by vegetative matter during biological processes. These emissions have not been previously accounted for and therefore the magnitude of their contribution to ozone concentrations has not been determined. A study of the emissions in the State of California was performed using 1987 as a base year. Data were collected on the acerages of natural and agricultural vegetation for each county in the state. Vegetation acreages were divided by season for direct input into air quality models. Generally, an inventory of the agricultural lands was more complicated than accounting for natural vegetation acreages. This was due to a large extent to crop rotation and production of more than one crop on the same land within the same calendar year. The amount of leaf biomass per acre was very difficult to define. Very little research has been completed in this area. In addition, several variables influence the amount of leaf biomass per acre. These include moisture, temperature, type of soil, insect/animal consumption, and agricultural practices

  15. Forces released during alignment with a preadjusted appliance with different types of elastomeric ligatures.

    Science.gov (United States)

    Franchi, Lorenzo; Baccetti, Tiziano

    2006-05-01

    The purpose of this in-vitro study was to compare the forces generated by new nonconventional elastomeric ligatures (NCEL) and conventional elastomeric ligatures (CEL) during leveling and aligning phases. The testing model consisted of 5 stainless steel 0.022-in preadjusted brackets for second premolar, first premolar, canine, lateral incisor, and central incisor. The canine bracket was welded to a sliding bar that allowed for different vertical positions. The forces generated by 3 sizes of wires (0.012-, 0.014-, and 0.016-in superelastic nickel-titanium) with the 2 types of elastomeric ligatures at different amounts of upward canine misalignment (1.5, 3, 4.5, and 6 mm) were recorded. Significant differences between CEL and NCEL were found for all tested variables (P <.01) with the exception of the 0.014- and 0.016-in wires at canine misalignment of 1.5 mm. A noticeable amount of force was generated with the NCEL at all 4 canine positions with all 3 wire sizes (from about 50 to about 150 g). With 4.5 mm of canine misalignment or more, the average amount of released force with the CEL was approximately zero.

  16. Controlled drug release on amine functionalized spherical MCM-41

    Energy Technology Data Exchange (ETDEWEB)

    Szegedi, Agnes, E-mail: szegedi@chemres.hu [Institute of Materials and Environmental Chemistry, Research Centre for Natural Sciences, Hungarian Academy of Sciences, 1025 Budapest, Pusztaszeri ut 59-67 (Hungary); Popova, Margarita; Goshev, Ivan [Institute of Organic Chemistry with Centre of Phytochemistry, Bulgarian Academy of Sciences, Sofia (Bulgaria); Klebert, Szilvia [Institute of Materials and Environmental Chemistry, Research Centre for Natural Sciences, Hungarian Academy of Sciences, 1025 Budapest, Pusztaszeri ut 59-67 (Hungary); Mihaly, Judit [Institute of Molecular Pharmacology, Research Centre for Natural Sciences, Hungarian Academy of Sciences, 1025 Budapest, Pusztaszeri ut 59-67 (Hungary)

    2012-10-15

    MCM-41 silica with spherical morphology and small particle sizes (100 nm) was synthesized and modified by post-synthesis method with different amounts of 3-aminopropyltriethoxysilane (APTES). A comparative study of the adsorption and release of a model drug, ibuprofen, was carried out. The modified and drug loaded mesoporous materials were characterized by XRD, TEM, N{sub 2} physisorption, elemental analysis, thermal analysis and FT-IR spectroscopy. A new method was developed for the quantitative determination of amino groups in surface modified mesoporous materials by the ninhydrin reaction. Good correlation was found between the amino content of the MCM-41 materials determined by the ninhydrin method and their ibuprofen adsorption capacity. Amino modification resulted in high degree of ibuprofen loading and slow release rate in comparison to the parent non-modified MCM-41. - Graphical abstract: Determination of surface amino groups by ninhidrin method. Highlights: Black-Right-Pointing-Pointer Spherical MCM-41 modified by different amounts of APTES was studied. Black-Right-Pointing-Pointer Ibuprofen (IBU) adsorption and release characteristics was tested. Black-Right-Pointing-Pointer The ninhydrin reaction was used for the quantitative determination of amino groups. Black-Right-Pointing-Pointer Stoichiometric amount of APTES is enough for totally covering the surface with amino groups. Black-Right-Pointing-Pointer Good correlation was found between the amino content and IBU adsorption capacity.

  17. Controlled drug release on amine functionalized spherical MCM-41

    International Nuclear Information System (INIS)

    Szegedi, Agnes; Popova, Margarita; Goshev, Ivan; Klébert, Szilvia; Mihály, Judit

    2012-01-01

    MCM-41 silica with spherical morphology and small particle sizes (100 nm) was synthesized and modified by post-synthesis method with different amounts of 3-aminopropyltriethoxysilane (APTES). A comparative study of the adsorption and release of a model drug, ibuprofen, was carried out. The modified and drug loaded mesoporous materials were characterized by XRD, TEM, N 2 physisorption, elemental analysis, thermal analysis and FT-IR spectroscopy. A new method was developed for the quantitative determination of amino groups in surface modified mesoporous materials by the ninhydrin reaction. Good correlation was found between the amino content of the MCM-41 materials determined by the ninhydrin method and their ibuprofen adsorption capacity. Amino modification resulted in high degree of ibuprofen loading and slow release rate in comparison to the parent non-modified MCM-41. - Graphical abstract: Determination of surface amino groups by ninhidrin method. Highlights: ► Spherical MCM-41 modified by different amounts of APTES was studied. ► Ibuprofen (IBU) adsorption and release characteristics was tested. ► The ninhydrin reaction was used for the quantitative determination of amino groups. ► Stoichiometric amount of APTES is enough for totally covering the surface with amino groups. ► Good correlation was found between the amino content and IBU adsorption capacity.

  18. Hydraulic running and release tool with mechanical emergency release

    International Nuclear Information System (INIS)

    Baker, S.F.

    1991-01-01

    This patent describes a setting tool for connection in a well string to position a tubular member in a well bore. It comprises: a mandrel adapted to be connected to the well string; an outer sleeve surrounding the mandrel and releasably secured thereto; a latch nut releasably connected to the outer sleeve; piston means sealingly engaging the mandrel; shear means releasably securing the piston to the latch nut to maintain the latch nut releasably connected to the tubular member; the mandrel having port means for conducting fluid pressure from the well string to release the piston means from and the latch nut; cooperating engageable surfaces on the piston and latch nut to reengage them together after the piston moves a predetermined longitudinal distance relative to the latch nut; and additional cooperating engageable surfaces on the latch nut and the outer sleeve which are engageable when the piston and engaged latch nut are moved a predetermined additional longitudinal distance by fluid pressure to secure the engaged piston and latch nut with the outer sleeve for retrieval along with the mandrel from the well bore

  19. Socioeconomic Status Moderates Genetic and Environmental Effects on the Amount of Alcohol Use

    Science.gov (United States)

    Hamdi, Nayla R; Krueger, Robert F.; South, Susan C.

    2015-01-01

    Background Much is unknown about the relationship between socioeconomic status (SES) and alcohol use, including the means by which SES may influence risk for alcohol use. Methods Using a sample of 672 twin pairs (aged 25–74) derived from the MacArthur Foundation Survey of Midlife Development in the United States (MIDUS), the present study examined whether SES, measured by household income and educational attainment, moderates genetic and environmental influences on three indices of alcohol use: amount used, frequency of use, and problem use. Results We found significant moderation for amount of alcohol used. Specifically, genetic effects were greater in low-SES conditions, shared environmental effects (i.e., environmental effects that enhance the similarity of twins from the same families) tended to increase in high-SES conditions, and non-shared environmental effects (i.e., environmental effects that distinguish twins) tended to decrease with SES. This pattern of results was found for both income and education, and it largely replicated at a second wave of assessment spaced nine years after the first. There was virtually no evidence of moderation for either frequency of alcohol use or alcohol problems. Conclusions Our findings indicate that genetic and environmental influences on drinking amount vary as a function of the broader SES context, whereas the etiologies of other drinking phenomena are less affected by this context. Efforts to find the causes underlying the amount of alcohol used are likely to be more successful if such contextual information is taken into account. PMID:25778493

  20. Socioeconomic status moderates genetic and environmental effects on the amount of alcohol use.

    Science.gov (United States)

    Hamdi, Nayla R; Krueger, Robert F; South, Susan C

    2015-04-01

    Much is unknown about the relationship between socioeconomic status (SES) and alcohol use, including the means by which SES may influence risk for alcohol use. Using a sample of 672 twin pairs (aged 25 to 74) derived from the MacArthur Foundation Survey of Midlife Development in the United States, this study examined whether SES, measured by household income and educational attainment, moderates genetic and environmental influences on 3 indices of alcohol use: amount used, frequency of use, and problem use. We found significant moderation for amount of alcohol used. Specifically, genetic effects were greater in low-SES conditions, shared environmental effects (i.e., environmental effects that enhance the similarity of twins from the same families) tended to increase in high-SES conditions, and nonshared environmental effects (i.e., environmental effects that distinguish twins) tended to decrease with SES. This pattern of results was found for both income and education, and it largely replicated at a second wave of assessment spaced 9 years after the first. There was virtually no evidence of moderation for either frequency of alcohol use or alcohol problems. Our findings indicate that genetic and environmental influences on drinking amount vary as a function of the broader SES context, whereas the etiologies of other drinking phenomena are less affected by this context. Efforts to find the causes underlying the amount of alcohol used are likely to be more successful if such contextual information is taken into account. Copyright © 2015 by the Research Society on Alcoholism.