The distribution characteristics of pollutants released at different cross-sectional positions of a river

International Nuclear Information System (INIS)

Huang Heqing; Chen Guang; Zhang Qianfeng

2010-01-01

The distribution characteristics of heavier or lighter pollutants released at different cross-sectional positions of a wide river is investigated with a well-tested three-dimensional numerical model of gravity flows based on Reynolds-Averaged Navier-Stokes equations and turbulence k-ε model. By focusing on investigating the influences of flow and buoyancy on pollutants, it is found that while carrying by the river flow downstream: i) a heavier pollutant released from the cross-sectional side position, forms transverse oscillation between two banks with decreased amplitude, i.e. forms kind of helical flow pattern along the straight part of channel bed; ii) a heavier pollutant released from the cross-sectional middle position, forms collapse oscillation in the middle of the straight channel part with reduced amplitude; iii) in the downstream sinuous channel, heavier pollutant is of higher concentration on the outer side of channel bends; iv) a light pollutant released from the cross-sectional side position, slips partly to the other side of the river, resulting in higher concentrations on two sides of the channel top; v) a light pollutant released from the cross-sectional middle position, splits into two parts symmetrically along two sides of the channel top; vi) in the downstream sinuous channel, light pollutant presents higher concentration on the inner side of channel bends. These findings may assist in cost-effective scientific countermeasures to be taken for accidental or planned pollutant releases into a river. - The distribution characteristics of heavier or lighter pollutants released at different cross-sectional positions of a river.

Release of gaseous tritium during reprocessing

International Nuclear Information System (INIS)

Bruecher, H.; Hartmann, K.

1983-01-01

About 50% of the tritium put through an LWR reprocessing plant is obtained as tritium-bearing water, HTO. Gaseous tritium, HT has a radiotoxicity which is by 4 orders of magnitude lower than that of HTO. A possibility for the removal of HTO could therefore be its conversion into the gas phase with subsequent emission of the HT into the atmosphere. However, model computations which are, in part, supported by experimental data reveal that the radiation exposure caused by HT release is only by about one order of magnitude below that caused by HTO. This is being attributed to the relatively quick reoxidation of HT by soil bacteria. Two alternatives for producing HT from HTO (electrolysis; voloxidation with subsequent electrolysis) are presented and compared with the reference process of deep-well injection of HTO. The authors come to the conclusion that tritium removal by HT release into the atmosphere cannot be recommended at present under either radiological or economic aspects. (orig.) [de

Determination of Radiological, Material and Organizational Measures for Reuse of Conditionally Released Materials from Decommissioning

International Nuclear Information System (INIS)

Ondra, F.; Vasko, M.; Necas, V.

2012-01-01

An important part of nuclear installation decommissioning is conditional release of materials. The mass of conditionally released materials can significantly influence radioactive waste management and capacity of radioactive waste repository. The influence on a total decommissioning cost is also not negligible. Several scenarios for reuse of conditionally released materials were developed within CONRELMAT project. Each scenario contains preparation phase, construction phase and operation phase. For each above mentioned phase is needed to determine radiological, material, organizational and other constraints for conditionally released materials reuse to not break exposure limits for staff and public. Constraints are determined on the basis of external and internal exposure calculations in created models for selected takes in particular scenarios phases. The paper presents a developed methodology for determination of part of above mentioned constraints concerning external exposure of staff or public. Values of staff external exposure are also presented in paper to ensure that staff or public exposure does not break the limits. The methodology comprises a proposal of following constraints: radionuclide limit concentration of conditionally released materials for specific scenarios and nuclide vectors, specific deployment of conditionally released materials eventually shielding materials, staff and public during the scenario's phases, organizational measures concerning time of staff's or public's stay in the vicinity of conditionally released materials for individual performed scenarios and nuclide vectors. The paper further describes VISIPLAN 3D ALARA calculation planning software tool used for calculation of staff's and public's external exposure for individual scenarios. Several other parallel papers proposed for HND2012 are presenting selected details of the project.(author).

27 CFR 24.159 - Release of collateral security.

Science.gov (United States)

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Release of collateral... § 24.159 Release of collateral security. Collateral security pledged and deposited will be released only in accordance with the provisions of 31 CFR part 225. The collateral security will not be released...

Cocaine- and amphetamine-regulated transcript is present in hypothalamic neuroendocrine neurones and is released to the hypothalamic-pituitary portal circuit

DEFF Research Database (Denmark)

Larsen, P J; Seier, V; Fink-Jensen, A

2003-01-01

Cocaine- and amphetamine-regulated transcript (CART) is present in a number of hypothalamic nuclei. Besides actions in circuits regulating feeding behaviour and stress responses, the hypothalamic functions of CART are largely unknown. We report that CART immunoreactivity is present in hypothalami......, supraoptic, paraventricular (PVN) and periventricular nuclei of the hypothalamus. In the PVN, CART-positive neuroendocrine neurones were found in all of cytoarchitectonically identified nuclei. In the periventricular nucleus, approximately one-third of somatostatin cells were also CART......-immunoreactive. In the medial parvicellular subnucleus of the PVN, CART and FG coexisted with thyrotrophin-releasing hormone, whereas very few of the corticotrophin-releasing hormone containing cells were CART-immunoreactive. In the arcuate nucleus, CART was extensively colocalized with pro...

27 CFR 17.114 - Release of collateral.

Science.gov (United States)

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Release of collateral. 17... PRODUCTS Bonds and Consents of Sureties Termination of Bonds § 17.114 Release of collateral. The release of collateral security pledged and deposited to satisfy the bond requirement of this part is governed by the...

PWR-GALE, Radioactive Gaseous Release and Liquid Release from PWR

International Nuclear Information System (INIS)

Chandrasekaran, T.; Lee, J.Y.; Willis, C.A.

1988-01-01

1 - Description of program or function: The PWR-GALE (Boiling Water Reactor Gaseous and Liquid Effluents) Code is a computerized mathematical model for calculating the release of radioactive material in gaseous and liquid effluents from pressurized water reactors (PWRs). The calculations are based on data generated from operating reactors, field tests, laboratory tests, and plant-specific design considerations incorporated to reduce the quantity of radioactive materials that may be released to the environment. 2 - Method of solution: GALE calculates expected releases based on 1) standardized coolant activities derived from ANS Standards 18.1 Working Group recommendations, 2) release and transport mechanisms that result in the appearance of radioactive material in liquid and gaseous waste streams, 3) plant-specific design features used to reduce the quantities of radioactive materials ultimately released to the environs, and 4) information received on the operation of nuclear power plants. 3 - Restrictions on the complexity of the problem: The liquid release portion of GALE uses subroutines taken from the ORIGEN (CCC-217) to calculate radionuclide buildup and decay during collection, processing, and storage of liquid radwaste. Memory requirements for this part of the program are determined by the large nuclear data base accessed by these subroutines

The NASA Electronic Parts and Packaging (NEPP) Program - Presentation to Korean Aerospace Research Institute

Science.gov (United States)

LaBel, Kenneth A.; Sampson, Michael J.

2016-01-01

This presentation will provide basic information about NASA's Electronic Parts and Packaging Program (NEPP), for sharing with representatives of the South Korean Aerospace Research Institute (KARI) as part of a larger presentation by Headquarters Office of Safety and Mission Assurance. The NEPP information includes mission and goals, history of the program, basic focus areas, strategies, deliverables and some examples of current tasks.

Strategies for making oral presentations about clinical issues: Part I. At the workplace.

Science.gov (United States)

Brown, Janet M; Schmidt, Nola A

2009-04-01

This column offers strategies that clinicians can use to make effective oral presentations at work. Part II, which will be published next month, will offer strategies for making oral presentations at professional conferences.

A 'Puff' dispersion model for routine and accidental releases

International Nuclear Information System (INIS)

Grsic, Z.; Rajkovic, B.; Milutinovic, P.

1999-01-01

A Puff dispersion model for accidental or routine releases is presented. This model was used as a constitutive part of an automatic meteorological station.All measured quantities are continuously displayed on PC monitor in a digital and graphical form, they are averaging every 10 minutes and sending to the civil information center of Belgrade. In the paper simulation of a pollutant plume dispersion from The oil refinery 'Pancevo', on April 18 th 1999 is presented. (author)

Environmental releases for calendar year 1993

International Nuclear Information System (INIS)

Thomas, S.P.; Curn, B.L.

1994-07-01

This report presents data on radioactive and nonradioactive materials released into the environment during calendar year 1993 from facilities managed by Westinghouse Hanford Company. As part of this executive summary, comprehensive data summaries of air emissions and liquid effluents in 1993 are displayed in tables. These tables represent the following: radionuclide air emissions data; data on radioactive liquid effluents discharged to the soil; radionuclides discharged to the Columbia River; nonradioactive air emissions data; total volumes and flow rates of 200/600 area liquid effluents. Both summary and detailed presentations of these data are given. When appropriate, comparisons to data from previous years are made

Minimizing employee exposure to toxic chemical releases

International Nuclear Information System (INIS)

Plummer, R.W.; Stobbe, T.J.; Mogensen, J.E.; Jeram, L.K.

1987-01-01

This book describes procedures for minimizing employee exposure to toxic chemical releases and suggested personal protective equipment (PPE) to be used in the event of such chemical release. How individuals, employees, supervisors, or companies perceive the risks of chemical exposure (risk meaning both probability of exposure and effect of exposure) determines to a great extent what precautions are taken to avoid risk. In Part I, the authors develop and approach which divides the project into three phases: kinds of procedures currently being used; the types of toxic chemical release accidents and injuries that occur; and, finally, integration of this information into a set of recommended procedures which should decrease the likelihood of a toxic chemical release and, if one does occur, will minimize the exposure and its severity to employees. Part II covers the use of personal protective equipment. It addresses the questions: what personal protective equipment ensembles are used in industry in situations where the release of a toxic or dangerous chemical may occur or has occurred; and what personal protective equipment ensembles should be used in these situations

Alveolar Soft Part Sarcoma Presenting as Hypervascular Adrenal Metastasis

Science.gov (United States)

Goroshi, Manjunath; Lila, Anurag R.; Bandgar, Tushar; Shah, Nalini S.

2018-01-01

Hypervascular adrenal masses include pheochromocytoma, metastases caused by clear renal cell carcinoma/hepatocellular carcinoma. Alveolar soft part sarcoma (ASPS) causing hypervascular metastases is not described in the literature. Here, we describe the first case of ASPS presenting as hypervascular metastasis. Our case was a 23-year-old male incidentally detected right adrenal mass during the evaluation of pain in the abdomen. On computed tomography (CT), adrenal mass showed bright enhancement in early arterial phase (unenhanced Hounsfield unit [HU]-45.3; arterial phase HU-158.2). 18- flurodeoxyglucose positron emission tomography/CT showed multiple lesions and was confirmed histologically to be due to ASPS. PMID:29398970

Pressure-sensitive release mechanism for radiosonde applications

International Nuclear Information System (INIS)

Kulhanek, F.C.

1975-01-01

As part of the 1975 planetary boundary layer field experimental program, miniature radiosondes attached to pilot balloons were released into the atmosphere for routine sampling of the vertical temperature distribution. A new releasing mechanism used to continue sampling during descent by parachute is described

Risk from a pressurized toxic gas system: Part 2, Dispersal consequences

International Nuclear Information System (INIS)

Brereton, S.J.; Martin, D.; Lane, S.G.; Altenbach, T.J.

1995-04-01

During the preparation of a Safety Analysis Report at the Lawrence Livermore National Laboratory, we studied the release of chlorine from a compressed gas experimental apparatus. This paper presents the second part in a series of two papers on this topic. The first paper focuses on the frequency of an unmitigated release from the system; this paper discusses the consequences of the release. The release of chlorine from the experimental apparatus was modeled as an unmitigated blowdown through a 0.25 inch (0.0064 m) outside diameter tube. The physical properties of chlorine were considered as were the dynamics of the fluid flow problem. The calculated release rate was used as input for the consequence assessment. Downwind concentrations as a function of time were evaluated and then compared to suggested guidelines. For comparison purposes, a typical water treatment plant was briefly studied. The lower hazard presented by the LLNL operation becomes evident when its release is compared to the release of material from a water treatment plant, a hazard which is generally accepted by the public

An investigation into the anti-releasing performance of a serrated bolt

Energy Technology Data Exchange (ETDEWEB)

Jeong, Jin Hwan; Lee, Hyun Kyu; Park, Ke Un; Kim, Jong Bong [Seoul Natinal University, Seoul (Korea, Republic of)

2015-11-15

As the sizes of electric products, such as mobile phones and watch phones, decrease, the joining bolt for the electric product should also be miniaturized. However, the miniature-sized bolt has to support sufficient joining torque and joining force. The bolt also has to support sufficient anti-releasing torque to keep the product fastened. We investigated a serrated bolt as a candidate for a miniature-sized fastener to increase the anti-release torque. In the serrated bolt, serration shapes are formed on the bottom surface of a bolt head to create an obstacle to releasing. In this study, finite element analyses were carried out on joining and releasing, and the anti-release torque was predicted. Through the joining and releasing analyses for various values of the elastic modulus and yield strength of the joined part, the effect of the mechanical properties of the joined part on the anti-releasing performance were investigated. The analysis results showed that a high strength insert nut is needed to increase the anti-releasing torque when the yield strength of the joined part is low, such as a plastic board in a mobile phone.

Data sheets of fission product release experiments for light water reactor fuel, (2)

International Nuclear Information System (INIS)

Ishiwatari, Nasumi; Nagai, Hitoshi; Takeda, Tsuneo; Yamamoto, Katsumune; Nakazaki, Chozaburo.

1979-07-01

This is the second data sheets of fission products (FP) release experiments for light water reactor fuel. Results of five FP release experiments from the third to the seventh are presented: results of pre-examinations of UO 2 pellets, photographs of parts of fuel rod assemblies for irradiation and the assemblies, operational conditions of JMTR and OWL-1, variations of radioiodine-131 level in the main loop coolant during experimental periods, and representative results of post-irradiation examinations of respective fuel rods. (author)

A simple operational gas release and swelling model. Pt. 1

International Nuclear Information System (INIS)

Wood, M.H.; Matthews, J.R.

1980-01-01

A new and simple model of fission gas release and swelling has been developed for oxide nuclear fuel under operational conditions. The model, which is to be incorporated into a fuel element behaviour code, is physically based and applicable to fuel at both thermal and fast reactor ratings. In this paper we present that part of the model describing the behaviour of intragranular gas: a future paper will detail the treatment of the grain boundary gas. The results of model calculations are compared with recent experimental observations of intragranular bubble concentrations and sizes, and gas release from fuel irradiated under isothermal conditions. Good agreement is found between experiment and theory. (orig.)

Hydrogen release from irradiated elastomers measured by Nuclear Reaction Analysis

Energy Technology Data Exchange (ETDEWEB)

Jagielski, J., E-mail: jacek.jagielski@itme.edu.pl [Institute for Electronic Materials Technology, Wolczynska 133, 01-926 Warszawa (Poland); National Centre for Nuclear Research, A. Soltana 7, 05-400 Swierk/Otwock (Poland); Ostaszewska, U. [Institute for Engineering of Polymer Materials & Dyes, Division of Elastomers & Rubber Technology, Harcerska 30, 05-820 Piastow (Poland); Bielinski, D.M. [Technical University of Lodz, Institute of Polymer & Dye Technology, Stefanowskiego 12/16, 90-924 Lodz (Poland); Grambole, D. [Institute of Ion Beam Physics and Materials Research, Helmholtz Zentrum Dresden Rossendorf, PO Box 51 01 19, D-01314 Dresden (Germany); Romaniec, M.; Jozwik, I.; Kozinski, R. [Institute for Electronic Materials Technology, Wolczynska 133, 01-926 Warszawa (Poland); Kosinska, A. [National Centre for Nuclear Research, A. Soltana 7, 05-400 Swierk/Otwock (Poland)

2016-03-15

Ion irradiation appears as an interesting method of modification of elastomers, especially friction and wear properties. Main structural effect caused by heavy ions is a massive loss of hydrogen from the surface layer leading to its smoothening and shrinking. The paper presents the results of hydrogen release from various elastomers upon irradiation with H{sup +}, He{sup +} and Ar{sup +} studied by using Nuclear Reaction Analysis (NRA) method. The analysis of the experimental data indicates that the hydrogen release is controlled by inelastic collisions between ions and target electrons. The last part of the study was focused on preliminary analysis of mechanical properties of irradiated rubbers.

Release kinetics and mechanisms of trace heavy metals from cement based material; Cinetiques et mecanismes de relargage des metaux lourds presents en traces dans les matrices cimentaires

Energy Technology Data Exchange (ETDEWEB)

Moudilou, E.

2002-12-15

Chemical species contained in a solid matrix may be transferred to the environment through water leaching. Previous studies of trace metals released from building materials (particularly cement-based ones) highlight an important analytical difficulty. The aim of this study is to determine the kinetics and the mechanisms involved in the release of trace heavy metals (Cr, Cu, Ni, Pb, V and Zn) from industrial cement pastes (usually ranging from 20 to 300 ppm). The development of a dynamic leaching system, named CTG-LEACHCRETE, (used at pH=5, 20 C) which permits the evaluation of the kinetics of trace heavy metals is presented in the first part. Also, innovative solid analysis techniques (ICP-MS-Laser Ablation, local and Grazing Incidence X-rays Diffraction (GIXD) technique) were used to characterise the cement-degraded layers formed during leaching experiments. These techniques enable to monitor the mineralogical evolution and the distribution of trace metals in these areas. The confrontation of these two approaches, kinetic and solid analysis, coupled with a thorough investigation of previously developed models, lead to proposals concerning the mechanisms of release of the trace heavy metals studied. In all the cement pastes studied (CPA-CEM I, CPJ-CEM II/A and CLC-CEM V/A), chromium is trapped in ettringite by substitution SO{sub 4}{sup 2-}(U)CrO{sub 4}{sup 2-} and its release is then controlled by the dissolution of this hydrate. The behaviour of copper, nickel and zinc in degraded areas and in leachates, are correlated to the silicon of the hydrated calcium silicate (CSH), which imply that they are localised there. Lead, was never detected in the leachates. But it is also correlated to the silicon in the degraded layers. (author)

Correlations in metal release profiles following sorption by Lemna minor.

Science.gov (United States)

Üçüncü Tunca, Esra; Ölmez, Tolga T; Özkan, Alper D; Altındağ, Ahmet; Tunca, Evren; Tekinay, Turgay

2016-08-02

Following the rapid uptake of contaminants in the first few hours of exposure, plants typically attempt to cope with the toxic burden by releasing part of the sorbed material back into the environment. The present study investigates the general trends in the release profiles of different metal(loid)s in the aquatic macrophyte Lemna minor and details the correlations that exist between the release of metal(loid) species. Water samples with distinct contamination profiles were taken from Nilüfer River (Bursa, Turkey), Yeniçağa Lake (Bolu, Turkey), and Beyşehir Lake (Konya, Turkey) and used for release studies; 36 samples were tested in total. Accumulation and release profiles were monitored over five days for 11 metals and a metalloid ((208)Pb, (111)Cd, (52)Cr,(53)Cr,(60)Ni,(63)Cu,(65)Cu,(75)As,(55)Mn, (137)Ba, (27)Al, (57)Fe, (66)Zn,(68)Zn) and correlation, cluster and principal component analyses were employed to determine the factors that affect the release of these elements. Release profiles of the tested metal(loid)s were largely observed to be distinct; however, strong correlations have been observed between certain metal pairs (Cr/Ni, Cr/Cu, Zn/Ni) and principal component analysis was able to separate the metal(loid)s into three well-resolved groups based on their release.

Potential of phytase-mediated iron release from cereal-based foods: a quantitative view

DEFF Research Database (Denmark)

Nielsen, Anne Veller Friis; Tetens, Inge; Meyer, Anne S.

2013-01-01

The major part of iron present in plant foods such as cereals is largely unavailable for direct absorption in humans due to complexation with the negatively charged phosphate groups of phytate (myo-inositol (1,2,3,4,5,6)-hexakisphosphate). Human biology has not evolved an efficient mechanism...... to naturally release iron from iron phytate complexes. This narrative review will evaluate the quantitative significance of phytase-catalysed iron release from cereal foods. In vivo studies have shown how addition of microbially derived phytases to cereal-based foods has produced increased iron absorption via...... phytate complexes, and (3) the extent of phytate dephosphorylation required for iron release from inositol phosphates is warranted. Phytase-mediated iron release can improve iron absorption from plant foods. There is a need for development of innovative strategies to obtain better effects....

Oxygenated gasoline release in the unsaturated zone - Part 1: Source zone behavior.

Science.gov (United States)

Freitas, Juliana G; Barker, James F

2011-11-01

Oxygenates present in gasoline, such as ethanol and MTBE, are a concern in subsurface contamination related to accidental spills. While gasoline hydrocarbon compounds have low solubility, MTBE and ethanol are more soluble, ethanol being completely miscible with water. Consequently, their fate in the subsurface is likely to differ from that of gasoline. To evaluate the fate of gasoline containing oxygenates following a release in the unsaturated zone shielded from rainfall/recharge, a controlled field test was performed at Canadian Forces Base Borden, in Ontario. 200L of a mixture composed of gasoline with 10% ethanol and 4.5% MTBE was released in the unsaturated zone, into a trench 20cm deep, about 32cm above the water table. Based on soil cores, most of the ethanol was retained in the source, above the capillary fringe, and remained there for more than 100 days. Ethanol partitioned from the gasoline to the unsaturated pore-water and was retained, despite the thin unsaturated zone at the site (~35cm from the top of the capillary fringe to ground surface). Due to its lower solubility, most of the MTBE remained within the NAPL as it infiltrated deeper into the unsaturated zone and accumulated with the gasoline on top of the depressed capillary fringe. Only minor changes in the distribution of ethanol were noted following oscillations in the water table. Two methods to estimate the capacity of the unsaturated zone to retain ethanol are explored. It is clear that conceptual models for sites impacted by ethanol-fuels must consider the unsaturated zone. Copyright © 2011 Elsevier B.V. All rights reserved.

47 CFR 1.1204 - Exempt ex parte presentations and proceedings.

Science.gov (United States)

2010-10-01

... may have an impact on that agency's jurisdictional responsibilities. If the agency involved does not... prescription of common carrier depreciation rates under section 220(b) of the Communications Act prior to release of a public notice of specific proposed depreciation rates (see also § 1.1206(a)(9)); (5) An...

Monitoring of the release of gaseous and aerosol-bound radioactive materials. Pt. 2

International Nuclear Information System (INIS)

1992-01-01

KTA 1503 contains requirements on technical installations and supplementary organizational measures considered necessary in order to monitor the release of gaseous and aerosol-bound radioactive materials. It consists of part 1: Monitoring of the release of radioactive materials together with stack gas during normal operation; part 2: Monitoring of the release of radioactive materials together with stack gas in the event of incidents; part 3: Monitoring of radioactive materials not released together with stack gas. The concept on which this rule is based is to ensure that in the case of incidents during which the result of effluent monitoring remains meaningful, such monitoring can be reliably performed. (orig./HSCH) [de

Evaluation of Management of Water Releases for Painted Rocks Reservoir, Bitterroot River, Montana, 1983-1986, Final Report.

Energy Technology Data Exchange (ETDEWEB)

Spoon, Ronald L. (Montana Department of Fish, Wildlife and Parks, Missoula, MT)

1987-06-01

This study was initiated in July, 1983 to develop a water management plan for the release of water purchased from Painted Rocks Reservoir. Releases were designed to provide optimum benefits to the Bitterroot River fishery. Fisheries, habitat, and stream flow information was gathered to evaluate the effectiveness of these supplemental releases in improving trout populations in the Bitterroot River. The study was part of the Northwest Power Planning Council's Fish and Wildlife Program and was funded by the Bonneville Power Administration. This report presents data collected from 1983 through 1986.

Controlled release of biofunctional substances by radiation-induced polymerization

International Nuclear Information System (INIS)

Yoshida, M.; Kumakura, M.; Kaetsu, I.

1978-01-01

The release behaviour of a drug from flat circular capsules obtained by radiation-induced polymerization at low temperatures and with different hydrophilic properties has been studied. The effect of various factors on release property was investigated. The release process could be divided into three parts, an initial quick release stage, stationary state release stage and a retarded release stage. Release behaviour in the stationary state was examined using Noyes-Whitney and Higuchi equations. It was shown that the hydrophilic property of polymer matrix expressed by water content was the most important effect on diffusion and release rate. Rigidity of the polymer may also affect diffusivity. The first quick release step could be attributed to rapid dissolution of drug in the matrix surface due to polymer swelling. (author)

Press releases — the new trend in science communication

DEFF Research Database (Denmark)

Autzen, Charlotte

2014-01-01

Scientific institutions have for a long time known the importance of framing and owning stories about science They also know the effective way of communicating science in a press release This is part of the institution’s public relations. Enhanced competition among research institutions has led...... to a buildup of communicative competences and professionalization of public relations inside the institutions and the press release has become an integrated part of science communication from these institutions. Changing working conditions in the media, where fewer people have to publish more, have made press...... releases from trustworthy scientific institutions into free and easily copied content for the editors. In this commentary I investigate and discuss the communicative ecosystem of the university press release. I especially take a close look at the role of the critical and independent science journalist...

Protecting privacy in data release

CERN Document Server

Livraga, Giovanni

2015-01-01

This book presents a comprehensive approach to protecting sensitive information when large data collections are released by their owners. It addresses three key requirements of data privacy: the protection of data explicitly released, the protection of information not explicitly released but potentially vulnerable due to a release of other data, and the enforcement of owner-defined access restrictions to the released data. It is also the first book with a complete examination of how to enforce dynamic read and write access authorizations on released data, applicable to the emerging data outsou

Slow release coating remedy for nitrogen loss from conventional urea: a review.

Science.gov (United States)

Naz, Muhammad Yasin; Sulaiman, Shaharin Anwar

2016-03-10

Developing countries are consuming major part of the global urea production with an anticipated nitrogen use efficiency of 20 to 35%. The release of excess nitrogen in the soil is not only detrimental to the environment but also lessens the efficiency of the conventional urea. The urea performance can be enhanced by encapsulating it with slow release coating materials and synchronizing the nutrients' release with the plant up-taking. However, the present cost of most of the coated fertilizers is considerably higher than the conventional fertilizers. The high cost factor prevents their widespread use in mainstream agriculture. This paper documents a review of literature related to the global urea market, issues pertaining to the conventional urea use, natural and synthetic materials for slow release urea and fluidized bed spray coating process. The aim of the current review is to develop technical understanding of the conventional and non-conventional coating materials and associated spray coating mechanism for slow release urea production. The study also investigated the potential of starch as the coating material in relation to the coatings tested previously for controlled release fertilizers. Copyright © 2016 Elsevier B.V. All rights reserved.

Training Materials for Release 3

DEFF Research Database (Denmark)

Wake, Jo Dugstad; Hansen, Cecilie; Debus, Kolja

This document, D7.4 – training materials for release 3, provides an overview of the training material for version 3 of the NEXT-TELL tools and methods. Previous documents submitted as part of work package 7, which is about teacher training, are D7.1 – Training Concept, D7.2 – Training Materials...... for Release 1 and D7.3 – Training Materials for Release 2. D7.4 builds on D7.1 and D7.2 and D7.3. D7.4 contains further development of previous work within WP7, essentially a revised theoretical approach to the teacher training, and expansion of the notion of tool training. The media in use have been expanded...

Calculation of tritium release from reactor's stack

International Nuclear Information System (INIS)

Akhadi, M.

1996-01-01

Method for calculation of tritium release from nuclear to environment has been discussed. Part of gas effluent contain tritium in form of HTO vapor released from reactor's stack was sampled using silica-gel. The silica-gel was put in the water to withdraw HTO vapor absorbed by silica-gel. Tritium concentration in the water was measured by liquid scintillation counter of Aloka LSC-703. Tritium concentration in the gas effluent and total release of tritium from reactor's stack during certain interval time were calculated using simple mathematic formula. This method has examined for calculation of tritium release from JRR-3M's stack of JAERI, Japan. From the calculation it was obtained the value of tritium release as much as 4.63 x 10 11 Bq during one month. (author)

Triggered Release from Polymer Capsules

Energy Technology Data Exchange (ETDEWEB)

Esser-Kahn, Aaron P. [Univ. of Illinois, Urbana, IL (United States). Beckman Inst. for Advanced Science and Technology and Dept. of Chemistry; Odom, Susan A. [Univ. of Illinois, Urbana, IL (United States). Beckman Inst. for Advanced Science and Technology and Dept. of Chemistry; Sottos, Nancy R. [Univ. of Illinois, Urbana, IL (United States). Beckman Inst. for Advanced Science and Technology and Dept. of Materials Science and Engineering; White, Scott R. [Univ. of Illinois, Urbana, IL (United States). Beckman Inst. for Advanced Science and Technology and Dept. of Aerospace Engineering; Moore, Jeffrey S. [Univ. of Illinois, Urbana, IL (United States). Beckman Inst. for Advanced Science and Technology and Dept. of Chemistry

2011-07-06

Stimuli-responsive capsules are of interest in drug delivery, fragrance release, food preservation, and self-healing materials. Many methods are used to trigger the release of encapsulated contents. Here we highlight mechanisms for the controlled release of encapsulated cargo that utilize chemical reactions occurring in solid polymeric shell walls. Triggering mechanisms responsible for covalent bond cleavage that result in the release of capsule contents include chemical, biological, light, thermal, magnetic, and electrical stimuli. We present methods for encapsulation and release, triggering methods, and mechanisms and conclude with our opinions on interesting obstacles for chemically induced activation with relevance for controlled release.

An unusual presentation of Pseudomonas aeruginosa blebitis following combined surgery

Directory of Open Access Journals (Sweden)

Shabana Bharathi

2014-01-01

Full Text Available We report a case of blebitis that occurred 3 years later following a combined glaucoma and cataract surgery. It was an atypical presentation, as patient had no classical fiery looking signs of blebitis despite the isolated organism being Pseudomonas aeruginosa. Improvized surgical techniques like use of Mitomycin C, releasable flap sutures though considered as part of the recommended procedure for better surgical outcomes, their role as potential risk factors for visually blinding complications like endophthalmitis are often overlooked. This case report throws light on such risk factors for bleb associated infections and recommends removal or trimming of all releasable sutures and the need for a regular postoperative follow-up.

Factors controlling alkali salt deposition in recovery boilers. Release mechanisms

Energy Technology Data Exchange (ETDEWEB)

McKeough, P; Kurkela, M; Kylloenen, H; Tapola, E [VTT Energy, Espoo (Finland). Process Technology Group

1997-10-01

The research was part of an ongoing cooperative research effort aimed at developing a model to describe the behaviour of inorganic compounds in kraft recovery boilers. During 1996 experimental investigations of sulphur release were continued. Experiments at elevated pressures and employing larger particle sizes were performed in order to gain information about mass transfer effects. The first experiments yielding data on the rates of the sulphur-release reactions were performed. This data will be used as the basis of a drop model for sulphur release being developed in cooperation with another research group. The other part of the work during 1996 explored the possibility of using chemical equilibrium calculations to predict the release of sodium, potassium and chlorine in the recovery furnace. The approach is essentially different from that employed in earlier studies in that the effects of fume formation are taken into account. So far, the predictions of the chemical equilibrium release model have, in no way, conflicted with field measurements. (orig.)

Potent agonists of growth hormone-releasing hormone. Part I.

Science.gov (United States)

Zarandi, M; Serfozo, P; Zsigo, J; Bokser, L; Janaky, T; Olsen, D B; Bajusz, S; Schally, A V

1992-03-01

Analogs of the 29 amino acid sequence of growth hormone-releasing hormone (GH-RH) with agmatine (Agm) in position 29 have been synthesized by the solid phase method, purified, and tested in vitro and in vivo. The majority of the analogs contained desaminotyrosine (Dat) in position 1, but a few of them had Tyr1, or N-MeTyr1. Some peptides contained one or more additional L- or D-amino acid substitutions in positions 2, 12, 15, 21, 27, and/or 28. Compared to the natural sequence of GH-RH(1-29)NH2, [Dat1,Ala15]GH-RH(1-28)Agm (MZ-3-191) and [D-Ala2,Ala15]GH-RH(1-28)Agm (MZ-3-201) were 8.2 and 7.1 times more potent in vitro, respectively. These two peptides contained Met27. Their Nle27 analogs, [Dat1,Ala15,Nle27]GH-RH(1-28)Agm(MZ-2-51), prepared previously (9), and [D-Ala2,Ala15,Nle28]GH-RH(1-28)Agm(MZ-3-195) showed relative in vitro potencies of 10.5 and 2.4, respectively. These data indicate that replacement of Met27 by Nle27 enhanced the GH-releasing activity of the analog when the molecule contained Dat1-Ala2 residues at the N-terminus, but peptides containing Tyr1-D-Ala2 in addition to Nle27 showed decreased potencies. Replacement of Ser28 with Asp in multi-substituted analogs of GH-RH(1-28)Agm resulted in a decrease in in vitro potencies compared to the parent compound. Thus, the Ser28-containing MZ-2-51, and [Dat1,Ala15,D-Lys21,Nle27]GH-RH(1-28)Agm, its Asp28 homolog (MZ-3-149), possessed relative activities of 10.5 and 5.6, respectively.(ABSTRACT TRUNCATED AT 250 WORDS)

Static and mobile networks design for atmospheric accidental releases monitoring

International Nuclear Information System (INIS)

Abida, R.

2010-01-01

The global context of my PhD thesis work is the optimization of air pollution monitoring networks, but more specifically it concerns the monitoring of accidental releases of radionuclides in air. The optimization problem of air quality measuring networks has been addresses in the literature. However, it has not been addresses in the context of surveillance of accidental atmospheric releases. The first part of my thesis addresses the optimization of a permanent network of monitoring of radioactive aerosols in the air, covering France. The second part concerns the problem of targeting of observations in case of an accidental release of radionuclides from a nuclear plant. (author)

Fission gas release behaviour in MOX fuels

International Nuclear Information System (INIS)

Viswanathan, U.K.; Anantharaman, S.; Sahoo, K.C.

2002-01-01

As a part of plutonium recycling programme MOX (U,Pu)O 2 fuels will be used in Indian boiling water reactors (BWR) and pressurised heavy water reactors (PHWR). Based on successful test irradiation of MOX fuel in CIRUS reactor, 10 MOX fuel assemblies have been loaded in the BWR of Tarapur Atomic Power Station (TAPS). Some of these MOX fuel assemblies have successfully completed the initial target average burnup of ∼16,000 MWD/T. Enhancing the burnup target of the MOX fuels and increasing loading of MOX fuels in TAPS core will depend on the feedback information generated from the measurement of released fission gases. Fission gas release behaviour has been studied in the experimental MOX fuel elements (UO 2 - 4% PuO 2 ) irradiated in pressurised water loop (PWL) of CIRUS. Eight (8) MOX fuel elements irradiated to an average burnup of ∼16,000 MWD/T have been examined. Some of these fuel elements contained controlled porosity pellets and chamfered pellets. This paper presents the design details of the experimental set up for studying fission gas release behaviour including measurement of gas pressure, void volume and gas composition. The experimental data generated is compared with the prediction of fuel performance modeling codes of PROFESS and GAPCON THERMAL-3. (author)

Past and present of risk assessment for RA-226 releases

International Nuclear Information System (INIS)

Paschoa, A.S.

1982-12-01

Some of the new concepts introduced by ICRP 26 seem to be difficult to apply to the case of dose limits concerning the 226 Ra releases from the front end of the nuclear fuel cycle. Accordingly most national legislations have not been permeated yet by the 226 Ra dose limits based on such concepts. This work calls the attention on the one hand that a loose concept of acceptable risk is implicitly used in a dose limitation system for 226 Ra when such system is based on calculating the dose as a fraction of the (MPC) sub(w) introduced earlier by the ICRP 2, and on the other hand that the ALI currently recommended by the ICRP 30 should be used only in the framework of the recommendations published in the ICRP 26, which adopts a better defined concept of risk. (Author) [pt

A self-referential HOWTO on release engineering

Energy Technology Data Exchange (ETDEWEB)

Galassi, Mark C. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2018-01-31

Release engineering is a fundamental part of the software development cycle: it is the point at which quality control is exercised and bug fixes are integrated. The way in which software is released also gives the end user her first experience of a software package, while in scientific computing release engineering can guarantee reproducibility. For these reasons and others, the release process is a good indicator of the maturity and organization of a development team. Software teams often do not put in place a release process at the beginning. This is unfortunate because the team does not have early and continuous execution of test suites, and it does not exercise the software in the same conditions as the end users. I describe an approach to release engineering based on the software tools developed and used by the GNU project, together with several specific proposals related to packaging and distribution. I do this in a step-by-step manner, demonstrating how this very paper is written and built using proper release engineering methods. Because many aspects of release engineering are not exercised in the building of the paper, the accompanying software repository also contains examples of software libraries.

Release to the environment and diffusion of radioiodine in the environment, 1

International Nuclear Information System (INIS)

Murata, Toshifumi

1979-01-01

1. Radioactivity of iodine nuclides accumulated in nuclear facilities. Radioactive iodine nuclides which are produced in nuclear plants consist mainly of short lived 131 I- 135 I, while 129 I with long half life is being produced in a small amount. The radioactivity of iodine in a power reactor of 1,000 MWe which burns uranium fuel amounts to about 6 x 10 8 C sub(i). In the case of fuel which is handled in a reprocessing plant of spent fuel, almost all radioactive iodine remaining in the fuel is 129 I (half life: 1.7 x 10 7 years) because of cooling period of more than 6 months which is imposed by the plant. 2. Release of radioactive iodine during normal operating conditions. In an event of fuel failure in light water cooled reactors, a part of radioactive iodine is dissolved in water and very small amount is released as gaseous iodine to the environment through the ventillation system. The actual amount of radioactive iodine which was released from various types of nuclear reactors in the world between 1970 to 1974 is recorded as much lower than to the presently regulated value in all cases. 3. Behavior of radioactive iodine during postulated accident. The amount of radioactive iodine which will be released from reactor core to the containment vessel varies with conditions to be assumed. In the event of a severe accidental condition such as fuel melt down or oxidation, 25% of radioactive iodine in the fuel are assumed to be released. The iodine released to the containment vessel is mostly removed by planting out to the wall of the containment or washed out by core spray, while the remaining part in air is to be removed by a filter unit which is installed in the emergency gas treatment system. (author)

Environmental releases for calendar year 1996

International Nuclear Information System (INIS)

Greager, E.M.

1997-01-01

This report presents data on radioactive and nonradioactive materials released into the environment during calendar year 1996 from facilities and activities managed by the Fluor Daniel Hanford, Incorporated (formerly the Westinghouse Hanford Company) and Bechtel Hanford, Incorporated. Fluor Daniel Hanford, Incorporated provides effluent monitoring services for Bechtel Hanford, Incorporated, which includes release reporting. Both summary and detailed presentations of the environmental releases are provided. When appropriate, comparisons to data from previous years are made

Environmental releases for calendar year 1996

Energy Technology Data Exchange (ETDEWEB)

Greager, E.M.

1997-07-31

This report presents data on radioactive and nonradioactive materials released into the environment during calendar year 1996 from facilities and activities managed by the Fluor Daniel Hanford, Incorporated (formerly the Westinghouse Hanford Company) and Bechtel Hanford, Incorporated. Fluor Daniel Hanford, Incorporated provides effluent monitoring services for Bechtel Hanford, Incorporated, which includes release reporting. Both summary and detailed presentations of the environmental releases are provided. When appropriate, comparisons to data from previous years are made.

Gliclazide directly inhibits arginine-induced glucagon release

DEFF Research Database (Denmark)

Cejvan, Kenan; Coy, David H; Holst, Jens Juul

2002-01-01

Arginine-stimulated insulin and somatostatin release is enhanced by the sulfonylurea gliclazide. In contrast, gliclazide inhibits the glucagon response. The aim of the present study was to investigate whether this inhibition of glucagon release was mediated by a direct suppressive effect of glicl......Arginine-stimulated insulin and somatostatin release is enhanced by the sulfonylurea gliclazide. In contrast, gliclazide inhibits the glucagon response. The aim of the present study was to investigate whether this inhibition of glucagon release was mediated by a direct suppressive effect....... In islet perifusions with DC-41-33, arginine-induced glucagon release was inhibited by 66%. We therefore concluded that gliclazide inhibits glucagon release by a direct action on the pancreatic A cell....

Release process for non-real property containing residual radioactive material

International Nuclear Information System (INIS)

Ranek, N.L.; Chen, S.Y.; Kamboj, S.; Hensley, J.; Burns, D.; Fleming, R.; Warren, S.; Wallo, A.

1997-01-01

It is DOE's objective to operate its facilities and to conduct its activities so that radiation exposures to members of the public are maintained within acceptable limits and exposures to residual radioactive materials are controlled. To accomplish this, DOE has adopted Order DOE 5400.51 'Radiation Protection of the Public and the Environment', and will be promulgating IO CR Part 834 to codify and clarify the requirements of DOE 5400.5. Under both DOE 5400.5 and 10 CR Part 834, radioactively contaminated DOE property is prohibited from release unless specific actions have been completed prior to the release. This paper outlines a ten-step process that, if followed, will assist DOE Operations and contractor personnel in ensuring that the required actions established by Order DOE 5400.5 and 10 CR Part 834 have been appropriately completed prior to the release for reuse or recycle of non-real property (e.g., office furniture, computers, hand tools, machinery, vehicles and scrap metal). Following the process will assist in ensuring that radiological doses to the public from the released materials will meet applicable regulatory standards and be as low as reasonably achievable (ALARA)

Evaluation of fuel release rate and mechanism tests under RBCB conditions

International Nuclear Information System (INIS)

Adamson, M.G.

1981-09-01

This task includes theoretical evaluation of fuel/fission product release behavior from failed LMFBR fuel elements as well as an on-going experimental investigation of the mechanism of oxide fuel dispersal into flowing liquid sodium. The primary objectives of this work are to develop a fuel source term that can be used in predictive models for primary heat transfer system contamination and to understand the separate influences of important system variables (such as flow rate, oxygen impurity level) on this source term. The present report is written in two parts: the first, in condensed form, is an updated evaluation of fuel (U,Pu) and fission product release data, and the second describes the current status of supporting experimental work at General Electric's Vallecitos Laboratory

Validation of software releases for CMS

International Nuclear Information System (INIS)

Gutsche, Oliver

2010-01-01

The CMS software stack currently consists of more than 2 Million lines of code developed by over 250 authors with a new version being released every week. CMS has setup a validation process for quality assurance which enables the developers to compare the performance of a release to previous releases and references. The validation process provides the developers with reconstructed datasets of real data and MC samples. The samples span the whole range of detector effects and important physics signatures to benchmark the performance of the software. They are used to investigate interdependency effects of all CMS software components and to find and fix bugs. The release validation process described here is an integral part of CMS software development and contributes significantly to ensure stable production and analysis. It represents a sizable contribution to the overall MC production of CMS. Its success emphasizes the importance of a streamlined release validation process for projects with a large code basis and significant number of developers and can function as a model for future projects.

Regulatory analysis on criteria for the release of patients administered radioactive material. Final report

Energy Technology Data Exchange (ETDEWEB)

Schneider, S.; McGuire, S.A.

1997-02-01

This regulatory analysis was developed to respond to three petitions for rulemaking to amend 10 CFR parts 20 and 35 regarding release of patients administered radioactive material. The petitions requested revision of these regulations to remove the ambiguity that existed between the 1-millisievert (0.1-rem) total effective dose equivalent (TEDE) public dose limit in Part 20, adopted in 1991, and the activity-based release limit in 10 CFR 35.75 that, in some instances, would permit release of individuals in excess of the current public dose limit. Three alternatives for resolution of the petitions were evaluated. Under Alternative 1, NRC would amend its patient release criteria in 10 CFR 35.75 to match the annual public dose limit in Part 20 of 1 millisievert (0.1 rem) TEDE. Alternative 2 would maintain the status quo of using the activity-based release criteria currently found in 10 CFR 35.75. Under Alternative 3, the NRC would revise the release criteria in 10 CFR 35.75 to specify a dose limit of 5 millisieverts (0.5 rem) TEDE.

Regulatory analysis on criteria for the release of patients administered radioactive material. Final report

International Nuclear Information System (INIS)

Schneider, S.; McGuire, S.A.

1997-02-01

This regulatory analysis was developed to respond to three petitions for rulemaking to amend 10 CFR parts 20 and 35 regarding release of patients administered radioactive material. The petitions requested revision of these regulations to remove the ambiguity that existed between the 1-millisievert (0.1-rem) total effective dose equivalent (TEDE) public dose limit in Part 20, adopted in 1991, and the activity-based release limit in 10 CFR 35.75 that, in some instances, would permit release of individuals in excess of the current public dose limit. Three alternatives for resolution of the petitions were evaluated. Under Alternative 1, NRC would amend its patient release criteria in 10 CFR 35.75 to match the annual public dose limit in Part 20 of 1 millisievert (0.1 rem) TEDE. Alternative 2 would maintain the status quo of using the activity-based release criteria currently found in 10 CFR 35.75. Under Alternative 3, the NRC would revise the release criteria in 10 CFR 35.75 to specify a dose limit of 5 millisieverts (0.5 rem) TEDE

A Self-Peeling Vat for Improved Release Capabilities During DLP Materials Processing

DEFF Research Database (Denmark)

Pedersen, David Bue; Zhang, Yang; Nielsen, Jakob Skov

2016-01-01

for an eased release of the manufactured part from the vat by means of a flexible membrane system. A membrane of fluorinated ethylene polymer will through elastic deformation automatically peel off the part as the part is lifted during layer changes. Peeling has been qualified by means of a truncated inverted...... cone as test geometry. As the cross-sectional diameter of the cone increase throughout the build-job, the geometry will release from the glass based build platform at the point where the peeling force exceed the adhesion force between platform and part. At failure point the lateral surface area...... of the top and bottom of the truncated cone is used as a measure of the performance of the vat with respect to release-capability. This has been tested at increasing manufacturing rates. The new self-peeling vat outperformed industrial state-of-the-art vats by 814% percent....

A Novel Approach for Dry Powder Coating of Pellets with Ethylcellulose. Part II: Evaluation of Caffeine Release.

Science.gov (United States)

Albertini, Beatrice; Melegari, Cecilia; Bertoni, Serena; Dolci, Luisa Stella; Passerini, Nadia

2018-04-01

The objective of this study was to assess the efficacy and the capability of a novel ethylcellulose-based dry-coating system to obtain prolonged and stable release profiles of caffeine-loaded pellets. Lauric and oleic acids at a suitable proportion were used to plasticize ethylcellulose. The effect of coating level, percentage of drug loading, inert core particle size, and composition of the coating formulation including the anti-sticking agent on the drug release profile were fully investigated. A coating level of 15% w/w was the maximum layered amount which could modify the drug release. The best controlled drug release was obtained by atomizing talc (2.5% w/w) together with the solid plasticizer during the dry powder-coating process. SEM pictures revealed a substantial drug re-crystallization on the pellet surface, and the release studies evidenced that caffeine diffused through the plasticized polymer acting as pore former. Therefore, the phenomenon of caffeine migration across the coating layer had a strong influence on the permeability of the coating membrane. Comparing dry powder-coated pellets to aqueous film-coated ones, drug migration happened during storage, though more sustained release profiles were obtained. The developed dry powder-coating process enabled the production of stable caffeine sustained release pellets. Surprisingly, the release properties of the dry-coated pellets were mainly influenced by the way of addition of talc into the dry powder-coating blend and by the drug nature and affinity to the coating components. It would be interesting to study the efficacy of novel coating system using a different API.

77 FR 13061 - Electronic Reporting of Toxics Release Inventory Data

Science.gov (United States)

2012-03-05

...--Reporting Year SIC--Standard Industrial Code TRI--Toxics Release Inventory TRI-ME--TRI-Made Easy Desktop... EPA to ``publish a uniform toxic chemical release form for facilities covered'' by the TRI Program. 42... practicable. Similarly, EPA's Cross-Media Electronic Reporting Regulation (CROMERR) (40 CFR Part 3), published...

Fission gas release and grain growth in THO2-UO2 fuel irradiated at high temperature

International Nuclear Information System (INIS)

Goldberg, I.; Waldman, L.A.; Giovengo, J.F.; Campbell, W.R.

1979-01-01

Data are presented on fission gas release and grain growth in ThO 2 -UO 2 fuels irradiated as part of the LWBR fuel element development program. These data for rods that experienced peak linear power outputs ranging from 15 to 22 KW/ft supplement fission gas release data previously reported for 51 rods containing ThO 2 and ThO 2 -UO 2 fuel irradiated at peak linear powers predominantly below 14 KW/ft. Fission gas release was relatively high (up to 15.0 percent) for the rods operated at high power in contrast to the relatively low fission gas release (0.1 to 5.2 percent) measured for the rods operated at lower power. Metallographic examination revealed extensive equiaxed grain growth in the fuel at the high power axial locations of the three rods

Applications of energy-release-rate techniques to part-through cracks in experimental pressure vessels

International Nuclear Information System (INIS)

Bass, B.R.; Bryan, R.H.; Bryson, J.W.; Merkle, J.G.

1982-01-01

In nonlinear applications of computational fracture mechanics, energy release rate techniques are used increasingly for computing stress intensity parameters of crack configurations. Recently, deLorenzi used the virtual-crack-extension method to derive an analytical expression for the energy release rate that is better suited for three-dimensional calculations than the well-known J-integral. Certain studies of fracture phenomena, such as pressurized-thermal-shock of cracked structures, require that crack tip parameters be determined for combined thermal and mechanical loads. A method is proposed here that modifies the isothermal formulation of deLorenzi to account for thermal strains in cracked bodies. This combined thermo-mechanical formulation of the energy release rate is valid for general fracture, including nonplanar fracture, and applies to thermo-elastic as well as deformation plasticity material models. Two applications of the technique are described here. In the first, semi-elliptical surface cracks in an experimental test vessel are analyzed under elastic-plastic conditions using the finite element method. The second application is a thick-walled test vessel subjected to combined pressure and thermal shock loadings

Release-ability of nano fillers from different nanomaterials (toward the acceptability of nanoproduct)

International Nuclear Information System (INIS)

Golanski, L.; Guiot, A.; Pras, M.; Malarde, M.; Tardif, F.

2012-01-01

It is of great interest to set up a reproducible and sensitive method able to qualify nanomaterials before their market introduction in terms of their constitutive nanoparticle release-ability in usage. Abrasion was performed on polycarbonate, epoxy, and PA11 polymers containing carbone nanotubes (CNT) up to 4 %wt. Using Taber linear standard tool and standard abrasion conditions no release from polymer coatings containing CNT was measured. In this study, new practical tools inducing non-standardized stresses able to compete with van der Waals forces were developed and tested on model polymers, showing controlled CNT dispersion. These stresses are still realistic, corresponding to scratching, instantaneous mechanical shocks, and abrasion of the surface. They offer an efficient way to quantify if release is possible from nanomaterials under different mechanical stresses and therefore give an idea about the mechanisms that favors it. Release under mechanical shocks and hard abrasion was obtained using these tools but only when nanomaterials present a bad dispersion of CNT within the epoxy matrix. Under the same conditions no release was obtained from the same material presenting a good dispersion. The CNT used in this study showed an external diameter Dext = 12 nm, an internal diameter Din = 5 nm, and a mean length of 1 μm. Release from paints under hard abrasion using a standard rotative Taber tool was obtained from a intentionaly non-optimized paint containing SiO 2 nanoparticles up to 35 %wt. The primary diameter of the SiO 2 was estimated to be around 12 nm. A metallic rake was efficient to remove nanoparticles from a non-woven fabric nanomaterial.

Neonatal finasteride administration decreases dopamine release in nucleus accumbens after alcohol and food presentation in adult male rats.

Science.gov (United States)

Llidó, Anna; Bartolomé, Iris; Darbra, Sònia; Pallarès, Marc

2016-08-01

Endogenous levels of the neurosteroid (NS) allopregnanolone (AlloP) during neonatal stages are crucial for the correct development of the central nervous system (CNS). In a recent work we reported that the neonatal administration of AlloP or finasteride (Finas), an inhibitor of the enzyme 5α-reductase needed for AlloP synthesis, altered the voluntary consumption of ethanol and the ventrostriatal dopamine (DA) levels in adulthood, suggesting that neonatal NS manipulations can increase alcohol abuse vulnerability in adulthood. Moreover, other authors have associated neonatal NS alterations with diverse dopaminergic (DAergic) alterations. Thus, the aim of the present work is to analyse if manipulations of neonatal AlloP alter the DAergic response in the nucleus accumbens (NAcc) during alcohol intake in rats. We administered AlloP or Finas from postnatal day (PND) 5 to PND9. At PND98, we measured alcohol consumption using a two-bottle free-choice model (ethanol 10% (v/v)+glucose 3% (w/v), and glucose 3% (w/v)) for 12 days. On the last day of consumption, we measured the DA and 3,4-dihydroxyphenylacetic acid (DOPAC) release in NAcc in response to ethanol intake. The samples were obtained by means of in vivo microdialysis in freely moving rats, and DA and DOPAC levels were determined by means of high-performance liquid chromatography analysis (HPLC). The results revealed that neonatal Finas increased ethanol consumption in some days of the consumption phase, and decreased the DA release in the NAcc in response to solutions (ethanol+glucose) and food presentation. Taken together, these results suggest that neonatal NS alterations can affect alcohol rewarding properties. Copyright © 2016 Elsevier B.V. All rights reserved.

75 FR 3593 - Concept Release on Equity Market Structure

Science.gov (United States)

2010-01-21

... Structure 2. Other Measures B. High Frequency Trading 1. Strategies a. Passive Market Making b. Arbitrage c... trend from a market structure with primarily manual trading to a market structure with primarily... Part III Securities and Exchange Commission 17 CFR Part 242 Concept Release on Equity Market...

Factors controlling alkalisalt deposition in recovery boiler- release mechanisms

Energy Technology Data Exchange (ETDEWEB)

McKeough, P.; Kylloenen, H.; Kurkela, M. [VTT Energy, Espoo (Finland). Process Technology Group

1996-12-01

As part of a cooperative effort to develop a model to describe the behaviour of inorganic compounds in kraft recovery boilers, an experimental investigation of the release of sulphur during black liquor pyrolysis has been undertaken. Previous to these studies, the mechanisms of sulphur release and the reasons for the observed effects of process conditions on sulphur release were very poorly understood. On the basis of the experimental results, the main reactions leading to sulphur release have been elucidated with a fair degree of certainty. Logical explanations for the variations of sulphur release with temperature and with liquor solids content have been proposed. The influence of pressure has been investigated in order to gain insights into the effects of mass transfer on the sulphur-release rate. In the near future, the research will be aimed at generating the kinetic data necessary for modelling the release of sulphur in the recovery furnace. (author)

Hanford Tank 241-C-106: Residual Waste Contaminant Release Model and Supporting Data

International Nuclear Information System (INIS)

Deutsch, William J.; Krupka, Kenneth M.; Lindberg, Michael J.; Cantrell, Kirk J.; Brown, Christopher F.; Schaef, Herbert T.

2005-01-01

CH2M HILL is producing risk/performance assessments to support the closure of single-shell tanks at the DOE's Hanford Site. As part of this effort, staff at PNNL were asked to develop release models for contaminants of concern that are present in residual sludge remaining in tank 241-C-106 (C-106) after final retrieval of waste from the tank. This report provides the information developed by PNNL

GEWEX SRB Shortwave Release 4

Science.gov (United States)

Cox, S. J.; Stackhouse, P. W., Jr.; Mikovitz, J. C.; Zhang, T.

2017-12-01

The NASA/GEWEX Surface Radiation Budget (SRB) project produces shortwave and longwave surface and top of atmosphere radiative fluxes for the 1983-near present time period. Spatial resolution is 1 degree. The new Release 4 uses the newly processed ISCCP HXS product as its primary input for cloud and radiance data. The ninefold increase in pixel number compared to the previous ISCCP DX allows finer gradations in cloud fraction in each grid box. It will also allow higher spatial resolutions (0.5 degree) in future releases. In addition to the input data improvements, several important algorithm improvements have been made since Release 3. These include recalculated atmospheric transmissivities and reflectivities yielding a less transmissive atmosphere. The calculations also include variable aerosol composition, allowing for the use of a detailed aerosol history from the Max Planck Institut Aerosol Climatology (MAC). Ocean albedo and snow/ice albedo are also improved from Release 3. Total solar irradiance is now variable, averaging 1361 Wm-2. Water vapor is taken from ISCCP's nnHIRS product. Results from GSW Release 4 are presented and analyzed. Early comparison to surface measurements show improved agreement.

Fluoride releasing and enamel demineralization around orthodontic brackets by fluoride-releasing composite containing nanoparticles.

Science.gov (United States)

Melo, Mary A S; Morais, Weslanny A; Passos, Vanara F; Lima, Juliana P M; Rodrigues, Lidiany K A

2014-05-01

Fluoride-containing materials have been suggested to control enamel demineralization around orthodontic brackets during the treatment with fixed appliances. The improvement of their properties has been made through innovations, such as the application of nanotechnology by incorporation of nanofillers. This in vitro study evaluated the capacity of fluoride releasing and enamel demineralization inhibition of fluoride-releasing nanofilled cement around orthodontic brackets using an artificial caries biofilm model. Forty bovine enamel discs were selected by evaluating surface microhardness and randomized into four groups (n = 10): non-fluoride-releasing microfilled composite, fluoride-releasing microfilled composite, resin-modified glass ionomer cement (RMGI), and fluoride-releasing nanofilled composite (FN). After brackets bonding in each disc, the specimens were subjected to a cariogenic challenge through a Streptococcus mutans biofilm model. After the experimental period, the biofilm formed around the brackets was collected for fluoride analysis and the mineral loss around the brackets was determined by integrated demineralization via cross-sectional microhardness measurement at 20 and 70 μm from the bracket margin. Additionally, samples of each group were subjected to energy-dispersive X-ray spectroscopy (EDX) analysis examined under a scanning electron microscopy (SEM). ANOVA followed by Tukey test were applied for fluoride concentration and mineral loss data, respectively. At both distances, only RMGI statistically differed from the other groups presenting the lowest demineralization, although there was a trend to a lower demineralization of enamel around brackets in FN group. Similar condition was found to fluoride concentration and EDX/SEM analysis. Under the cariogenic exposure condition of this study, the fluoride-releasing nanofilled material had similar performance to fluoride-releasing microfilled materials. The presence of nanofillers in the fluoride-releasing

The OCaml system release 4.04: Documentation and user's manual

OpenAIRE

Leroy, Xavier; Doligez, Damien; Frisch, Alain; Garrigue, Jacques; Rémy, Didier; Vouillon, Jérôme

2016-01-01

This manual documents the release 4.04 of the OCaml system. It is organized as follows. Part I, "An introduction to OCaml", gives an overview of the language. Part II, "The OCaml language", is the reference description of the language. Part III, "The OCaml tools", documents the compilers, toplevel system, and programming utilities. Part IV, "The OCaml library", describes the modules provided in the standard library.

The OCaml system release 4.02: Documentation and user's manual

OpenAIRE

Leroy, Xavier; Doligez, Damien; Frisch, Alain; Garrigue, Jacques; Rémy, Didier; Vouillon, Jérôme

2014-01-01

This manual documents the release 4.02 of the OCaml system. It is organized as follows. Part I, "An introduction to OCaml", gives an overview of the language. Part II, "The OCaml language", is the reference description of the language. Part III, "The OCaml tools", documents the compilers, toplevel system, and programming utilities. Part IV, "The OCaml library", describes the modules provided in the standard library.

The OCaml system release 4.06: Documentation and user's manual

OpenAIRE

Leroy , Xavier; Doligez , Damien; Frisch , Alain; Garrigue , Jacques; Rémy , Didier; Vouillon , Jérôme

2017-01-01

This manual documents the release 4.06 of the OCaml system. It is organized as follows. Part I, "An introduction to OCaml", gives an overview of the language. Part II, "The OCaml language", is the reference description of the language. Part III, "The OCaml tools", documents the compilers, toplevel system, and programming utilities. Part IV, "The OCaml library", describes the modules provided in the standard library.

Protective action evaluation, Part 1. Effectiveness of sheltering as a protective action against nuclear accidents involving gaseous releases

International Nuclear Information System (INIS)

Anno, G.H.; Dore, M.A.

1978-04-01

In an airborne release of radioactive material from a nuclear power plant accident, sheltering of individuals is of importance in emergency protective action planning. An analysis to estimate the effectiveness or benefit that might be derived from sheltering is described. The objective of this effort is the development of sheltering effectiveness information for those responsible for formulating required emergency plans for nuclear power plant siting. Shelter effectiveness is specifically defined as the dose reduction factor (DRF). DRF estimates for different conditions of source release, shelter structure assumptions, and operational time parameters are made for both whole-body and thyroid doses separately, based on a single-compartment structural model of the time-varying outside and inside gaseous radionuclide sources of krypton, zenon, and iodine. Design basis accident (DBA) assumptions are made for the gaseous radionuclide release. The magnitude of the release and dose estimates are based on radionuclide data from The Reactor Safety Study (WASH-1400). Source release time and duration assumptions are related to release categories PWR 1, PWR 3, and PWR 4, for which release times range from 1.5 to 2.5 hr and the release duration ranges from 0.5 to 3 hr. The basic shelter model characteristics considered are gamma ray attentuation, source geometry, gaseous fission-product ingress, and air change rate. Temporal parameters considered are source release time and duration, cloud travel time, and time spent in the shelter structure. Also, the analysis of shelter effectiveness is based on a time-frame model, which can be conveniently related to other operational times important for emergency planning. In addition to developing shelter-effectiveness estimates parametrically, the advantage of exiting and evacuating the vicinity of the shelter area after some initial time in the shelter is analyzed from the standpoint of the DRF and temporal considerations

Endometriosis presenting as inguinal mass attached to the extra pelvic part of round ligament

International Nuclear Information System (INIS)

Ibrahim, N.T.

2013-01-01

Endometriosis attached to extra pelvic part of the round ligament is rare. Preoperative diagnosis is difficult but history and presentation may guide to diagnosis which is confirmed on histology. A woman aged 29 years presented with painful right inguinal mass whose intensity of pain and size changed with menstrual cycle. Physical examination revealed right inguinal hard, fixed mass measuring 2*2 cm. Ultrasound, computed tomography, and fine needle aspiration cytology were normal therefore, excision of the mass was done along with histology which,confirmed endometriosis; simultaneous laparoscopy was performed which showed peritoneal endometriosis too. (author)

Observations of the release of non-methane hydrocarbons from fractured shale.

Science.gov (United States)

Sommariva, Roberto; Blake, Robert S; Cuss, Robert J; Cordell, Rebecca L; Harrington, Jon F; White, Iain R; Monks, Paul S

2014-01-01

The organic content of shale has become of commercial interest as a source of hydrocarbons, owing to the development of hydraulic fracturing ("fracking"). While the main focus is on the extraction of methane, shale also contains significant amounts of non-methane hydrocarbons (NMHCs). We describe the first real-time observations of the release of NMHCs from a fractured shale. Samples from the Bowland-Hodder formation (England) were analyzed under different conditions using mass spectrometry, with the objective of understanding the dynamic process of gas release upon fracturing of the shale. A wide range of NMHCs (alkanes, cycloalkanes, aromatics, and bicyclic hydrocarbons) are released at parts per million or parts per billion level with temperature- and humidity-dependent release rates, which can be rationalized in terms of the physicochemical characteristics of different hydrocarbon classes. Our results indicate that higher energy inputs (i.e., temperatures) significantly increase the amount of NMHCs released from shale, while humidity tends to suppress it; additionally, a large fraction of the gas is released within the first hour after the shale has been fractured. These findings suggest that other hydrocarbons of commercial interest may be extracted from shale and open the possibility to optimize the "fracking" process, improving gas yields and reducing environmental impacts.

75 FR 75573 - Standards Governing the Release of a Suspicious Activity Report

Science.gov (United States)

2010-12-03

... Part III Department of the Treasury Comptroller of the Currency 12 CFR Parts 4 and 21 Office of Thrift Supervision 12 CFR Parts 510 and 563 31 CFR Part 103 Standards Governing the Release of a... THE TREASURY Office of the Comptroller of the Currency 12 CFR Part 4 [Docket ID OCC-2010-0018] RIN...

Decontamination for free release

Energy Technology Data Exchange (ETDEWEB)

Simpson, K A; Elder, G R [Bradtec Ltd., Bristol (United Kingdom)

1997-02-01

Many countries are seeking to treat radioactive waste in ways which meet the local regulatory requirements, but yet are cost effective when all contributing factors are assessed. In some countries there are increasing amounts of waste, arising from nuclear plant decommissioning, which are categorized as low level waste: however with suitable treatment a large part of such wastes might become beyond regulatory control and be able to be released as non-radioactive. The benefits and disadvantages of additional treatment before disposal need to be considered. Several processes falling within the overall description of decontamination for free release have been developed and applied, and these are outlined. In one instance the process seeks to take advantage of techniques and equipment used for decontaminating water reactor circuits intermittently through reactor life. (author). 9 refs, 1 fig., 3 tabs.

Modeling of fission product release in integral codes

International Nuclear Information System (INIS)

Obaidurrahman, K.; Raman, Rupak K.; Gaikwad, Avinash J.

2014-01-01

The Great Tohoku earthquake and tsunami that stroke the Fukushima-Daiichi nuclear power station in March 11, 2011 has intensified the needs of detailed nuclear safety research and with this objective all streams associated with severe accident phenomenology are being revisited thoroughly. The present paper would cover an overview of state of art FP release models being used, the important phenomenon considered in semi-mechanistic models and knowledge gaps in present FP release modeling. Capability of FP release module, ELSA of ASTEC integral code in appropriate prediction of FP release under several diversified core degraded conditions will also be demonstrated. Use of semi-mechanistic fission product release models at AERB in source-term estimation shall be briefed. (author)

32 CFR Appendix G to Part 275 - Releasing Information Obtained From Financial Institutions

Science.gov (United States)

2010-07-01

... SECRETARY OF DEFENSE (CONTINUED) MISCELLANEOUS OBTAINING INFORMATION FROM FINANCIAL INSTITUTIONS: RIGHT TO... Financial Institutions A. Financial records obtained under 12 U.S.C. chapter 35 shall be marked: “This... 32 National Defense 2 2010-07-01 2010-07-01 false Releasing Information Obtained From Financial...

Mercury release from fly ashes and hydrated fly ash cement pastes

Science.gov (United States)

Du, Wen; Zhang, Chao-yang; Kong, Xiang-ming; Zhuo, Yu-qun; Zhu, Zhen-wu

2018-04-01

The large-scale usage of fly ash in cement and concrete introduces mercury (Hg) into concrete structures and a risk of secondary emission of Hg from the structures during long-term service was evaluated. Three fly ashes were collected from coal-fired power plants and three blend cements were prepared by mixing Ordinary Portland cement (OPC) with the same amount of fly ash. The releasing behaviors of Hg0 from the fly ash and the powdered hydrated cement pastes (HCP) were measured by a self-developed Hg measurement system, where an air-blowing part and Hg collection part were involved. The Hg release of fly ashes at room temperature varied from 25.84 to 39.69 ng/g fly ash during 90-days period of air-blowing experiment. In contrast, the Hg release of the HCPs were in a range of 8.51-18.48 ng/g HCP. It is found that the Hg release ratios of HCPs were almost the same as those of the pure fly ashes, suggesting that the hydration products of the HCP have little immobilization effect on Hg0. Increasing temperature and moisture content markedly promote the Hg release.

Predicting hydrocarbon release from soil

International Nuclear Information System (INIS)

Poppendieck, D.; Loehr, R.C.

2002-01-01

'Full text:' The remediation of hazardous chemicals from soils can be a lengthy and costly process. As a result, recent regulatory initiatives have focused on risk-based corrective action (RBCA) approaches. Such approaches attempt to identify the amount of chemical that can be left at a site with contaminated soil and still be protective of human health and the environment. For hydrocarbons in soils to pose risk to human heath and the environment, the hydrocarbons must be released from the soil and accessible to microorganisms, earthworms, or other higher level organisms. The sorption of hydrocarbons to soil can reduce the availability of the hydrocarbon to receptors. Typically in soils and sediments, there is an initial fast release of a hydrocarbon from the soil to the aqueous phase followed by a slower release of the remaining hydrocarbon to the aqueous phase. The rate and extent of slow release can influence aqueous hydrocarbon concentrations and the fate and transport of hydrocarbons in the subsurface. Once the fast fraction of the chemical has been removed from the soil, the remaining fraction of a chemical may desorb at a rate that natural mechanisms can attenuate the released hydrocarbon. Hence, active remediation may be needed only until the fast fraction has been removed. However, the fast fraction is a soil and chemical specific parameter. This presentation will present a tier I type protocol that has been developed to quickly estimate the fraction of hydrocarbons that are readily released from the soil matrix to the aqueous phase. Previous research in our laboratory and elsewhere has used long-term desorption (four months) studies to determine the readily released fraction. This research shows that a single short-term (less than two weeks) batch extraction procedure provides a good estimate of the fast released fraction derived from long-term experiments. This procedure can be used as a tool to rapidly evaluate the release and bioavailability of

Morphology of Gas Release in Physical Simulants

Energy Technology Data Exchange (ETDEWEB)

Daniel, Richard C.; Burns, Carolyn A.; Crawford, Amanda D.; Hylden, Laura R.; Bryan, Samuel A.; MacFarlan, Paul J.; Gauglitz, Phillip A.

2014-07-03

This report documents testing activities conducted as part of the Deep Sludge Gas Release Event Project (DSGREP). The testing described in this report focused on evaluating the potential retention and release mechanisms of hydrogen bubbles in underground radioactive waste storage tanks at Hanford. The goal of the testing was to evaluate the rate, extent, and morphology of gas release events in simulant materials. Previous, undocumented scoping tests have evidenced dramatically different gas release behavior from simulants with similar physical properties. Specifically, previous gas release tests have evaluated the extent of release of 30 Pa kaolin and 30 Pa bentonite clay slurries. While both materials are clays and both have equivalent material shear strength using a shear vane, it was found that upon stirring, gas was released immediately and completely from bentonite clay slurry while little if any gas was released from the kaolin slurry. The motivation for the current work is to replicate these tests in a controlled quality test environment and to evaluate the release behavior for another simulant used in DSGREP testing. Three simulant materials were evaluated: 1) a 30 Pa kaolin clay slurry, 2) a 30 Pa bentonite clay slurry, and 3) Rayleigh-Taylor (RT) Simulant (a simulant designed to support DSGREP RT instability testing. Entrained gas was generated in these simulant materials using two methods: 1) application of vacuum over about a 1-minute period to nucleate dissolved gas within the simulant and 2) addition of hydrogen peroxide to generate gas by peroxide decomposition in the simulants over about a 16-hour period. Bubble release was effected by vibrating the test material using an external vibrating table. When testing with hydrogen peroxide, gas release was also accomplished by stirring of the simulant.

Analysis of drug effects on neurotransmitter release

International Nuclear Information System (INIS)

Rowell, P.; Garner, A.

1986-01-01

The release of neurotransmitter is routinely studied in a superfusion system in which serial samples are collected and the effects of drugs or other treatments on the amount of material in the superfusate is determined. With frequent sampling interval, this procedure provides a mechanism for dynamically characterizing the release process itself. Using automated data collection in conjunction with polyexponential computer analysis, the equation which describes the release process in each experiment is determined. Analysis of the data during the nontreated phase of the experiment allows an internal control to be used for accurately assessing any changes in neurotransmitter release which may occur during a subsequent treatment phase. The use of internal controls greatly improves the signal to noise ratio and allows determinations of very low concentrations of drugs on small amounts of tissue to be made. In this presentation, the effects of 10 μM nicotine on 3 H-dopamine release in rat nucleus accumbens is described. The time course, potency and efficacy of the drug treatment is characterized using this system. Determinations of the exponential order of the release as well as the rate constants allow one to study the mechanism of the release process. A description of 3 H-dopamine release in normal as well as Ca ++ -free medium is presented

Association between high risk papillomavirus DNA and nitric oxide release in the human uterine cervix.

Science.gov (United States)

Rahkola, Paivi; Mikkola, Tomi S; Ylikorkala, Olavi; Vaisanen-Tommiska, Mervi

2009-08-01

Local cervical factors may determine the outcome of human papillomavirus (HPV) infection. Nitric oxide (NO) may be one such factor, since it is produced by uterine cervical cells and it takes part in both immunological and carcinogenic reactions. We studied the association between the presence of cervical high risk (hr) HPV DNA and NO in the cervical canal in women. High risk HPV DNA status was assessed from 328 women by using a specific DNA test and the release of cervical NO was assessed as nitrate/nitrite in cervical fluid. Cervical NO was then compared between women showing different status of hr HPV DNA and different cytological and histological findings. High risk HPV DNA was present in 175/328 (53%) women. The cervical NO release in women with hr HPV DNA was 90% higher compared to hr HPV DNA negative women (poral contraception, intrauterine devices, or signs of bacterial vaginosis or candida infection. Cytologically healthy epithelium and epithelium with mild cytological or histological changes showed elevated NO release if hr HPV DNA was present. The presence of hr HPV DNA is associated with an increased release of NO in the human uterine cervix. The clinical significance of this phenomenon remains open.

Cumulative release to the accessible environment

International Nuclear Information System (INIS)

Kanehiro, B.

1985-01-01

The Containment and Isolation Working Group considered issues related to the postclosure behavior of repositories in crystalline rock. This working group was further divided into subgroups to consider the progress since the 1978 GAIN Symposium and identify research needs in the individual areas of regional ground-water flow, ground-water travel time, fractional release, and cumulative release. The analysis and findings of the Fractional Release Subgroup are presented

Decontamination and free release of reactor pond furniture

International Nuclear Information System (INIS)

Burke, S.P.; Sanders, M.J.

1993-01-01

As part of the Stage 1 decommissioning project for the Steam Generating Heavy Water Reactor (SGHWR) at AEA Technology's Winfrith site in the UK, the 20 fuel racks in the fuel pond are to be removed. At Winfrith, considerable experience of waste disposal via the free release (below regulatory concern) route has been built up. Using a redundant rack, a trial was carried out to assess the technical and economic feasibility of the decontamination/free release route. An electrochemical process was employed. The trial successfully demonstrated technical feasibility, and an economic assessment concluded that the route can be justified financially. Therefore a decision was taken to dispose of all the racks by decontamination and free release. (Author)

Techniques to limit gaseous releases in case of reactor accident. Choice criteria - present solutions

International Nuclear Information System (INIS)

Billard, Francois; Lavie, Jean-Marie

1964-10-01

Within the frame of the study of radiological risks associated with a reactor accident in order to define the required responses, this study comprises, on the one hand, an analysis of the different accident types in order to select typical accidents, and on the other hand, a site-based analysis to define the maximum admissible radioactivity release for a given site. The determination of minimum required coefficient of risk reduction results from a compromise between the choice of reactor configuration type and the efficiency of purification devices, while taking into account minimum characteristics of the enclosure mechanical strength, local release conditions, and nature of gaseous effluents to be processed. After a review of available containment techniques, the author applies this analysis method to the different French reactor types. He gives a brief description of adopted solutions for the most typical French reactors in terms of characteristics of venting and filtration devices. As data quality is a crucial requirement, the author outlines the need for further studies regarding fission product emission and transfer, the purification of gaseous effluents and their diffusion in the atmosphere [fr

Controlled release system for ametryn using polymer microspheres: Preparation, characterization and release kinetics in water

International Nuclear Information System (INIS)

Grillo, Renato; Pereira, Anderson do Espirito Santo; Ferreira Silva de Melo, Nathalie; Porto, Raquel Martins; Feitosa, Leandro Oliveira; Tonello, Paulo Sergio; Dias Filho, Newton L.; Rosa, Andre Henrique; Lima, Renata; Fraceto, Leonardo Fernandes

2011-01-01

The purpose of this work was to develop a modified release system for the herbicide ametryn by encapsulating the active substance in biodegradable polymer microparticles produced using the polymers poly(hydroxybutyrate) (PHB) or poly(hydroxybutyrate-valerate) (PHBV), in order to both improve the herbicidal action and reduce environmental toxicity. PHB or PHBV microparticles containing ametryn were prepared and the efficiencies of herbicide association and loading were evaluated, presenting similar values of approximately 40%. The microparticles were characterized by scanning electron microscopy (SEM), which showed that the average sizes of the PHB and PHBV microparticles were 5.92 ± 0.74 μm and 5.63 ± 0.68 μm, respectively. The ametryn release profile was modified when it was encapsulated in the microparticles, with slower and more sustained release compared to the release profile of pure ametryn. When ametryn was associated with the PHB and PHBV microparticles, the amount of herbicide released in the same period of time was significantly reduced, declining to 75% and 87%, respectively. For both types of microparticle (PHB and PHBV) the release of ametryn was by diffusion processes due to anomalous transport (governed by diffusion and relaxation of the polymer chains), which did not follow Fick's laws of diffusion. The results presented in this paper are promising, in view of the successful encapsulation of ametryn in PHB or PHBV polymer microparticles, and indications that this system may help reduce the impacts caused by the herbicide, making it an environmentally safer alternative.

InAs migration on released, wrinkled InGaAs membranes used as virtual substrate

International Nuclear Information System (INIS)

Filipe Covre da Silva, S; Lanzoni, E M; De Araujo Barboza, V; Deneke, Ch; Malachias, A; Kiravittaya, S

2014-01-01

Partly released, relaxed and wrinkled InGaAs membranes are used as virtual substrates for overgrowth with InAs. Such samples exhibit different lattice parameters for the unreleased epitaxial parts, the released flat, back-bond areas and the released wrinkled areas. A large InAs migration towards the released membrane is observed with a material accumulation on top of the freestanding wrinkles during overgrowth. A semi-quantitative analysis of the misfit strain shows that the material migrates to the areas of the sample with the lowest misfit strain, which we consider as the areas of the lowest chemical potential of the surface. Material migration is also observed for the edge-supported, freestanding InGaAs membranes found on these samples. Our results show that the released, wrinkled nanomembranes offer a growth template for InAs deposition that fundamentally changes the migration behavior of the deposited material on the growth surface. (paper)

Atmospheric Release Advisory Capability

International Nuclear Information System (INIS)

Dickerson, M.H.; Gudiksen, P.H.; Sullivan, T.J.

1983-02-01

The Atmospheric Release Advisory Capability (ARAC) project is a Department of Energy (DOE) sponsored real-time emergency response service available for use by both federal and state agencies in case of a potential or actual atmospheric release of nuclear material. The project, initiated in 1972, is currently evolving from the research and development phase to full operation. Plans are underway to expand the existing capability to continuous operation by 1984 and to establish a National ARAC Center (NARAC) by 1988. This report describes the ARAC system, its utilization during the past two years, and plans for its expansion during the next five to six years. An integral part of this expansion is due to a very important and crucial effort sponsored by the Defense Nuclear Agency to extend the ARAC service to approximately 45 Department of Defense (DOD) sites throughout the continental US over the next three years

Improving the quality of EMI Releases by leveraging the EMI Testing Infrastructure

International Nuclear Information System (INIS)

Aiftimiei, C; Ceccanti, A; Dongiovanni, D; Giacomini, F; Meglio, A Di

2012-01-01

What is an EMI Release? What is its life cycle? How is its quality assured through a continuous integration and large scale acceptance testing? These are the main questions that this article will answer, by presenting the EMI release management process with emphasis on the role played by the Testing Infrastructure in improving the quality of the middleware provided by the project. The European Middleware Initiative (EMI) is a close collaboration of four major European technology providers: ARC, gLite, UNICORE and dCache. Its main objective is to deliver a consolidated set of components for deployment in EGI (as part of the Unified Middleware Distribution, UMD), PRACE and other DCIs. The harmonized set of EMI components thus enables the interoperability and integration between Grids. EMI aims at creating an effective environment that satisfies the requirements of the scientific communities relying on it. The EMI distribution is organized in periodic major releases whose development and maintenance follow a 5-phase yearly cycle: i) requirements collection and analysis; ii) development and test planning; iii) software development, testing and certification; iv) release certification and validation and v) release and maintenance. In this article we present in detail the implementation of operational and infrastructural resources supporting the certification and validation phase of the release. The main goal of this phase is to harmonize into a single release the strongly inter-dependent products coming from various development teams through parallel certification paths. To achieve this goal the continuous integration and large scale acceptance testing performed on the EMI Testing Infrastructure plays a key role. The purpose of this infrastructure is to provide a system where both the production and the release candidate product versions are deployed. On this system inter-component testing by different product team testers can concurrently take place. The Testing

Experimental and theoretical studies on water and gas release from heated concrete

International Nuclear Information System (INIS)

McCormack, J.D.; Postma, A.K.

1977-01-01

Procedures currently used in licensing of nuclear facilities require analysis of postulated accidents which are more severe than ''design basis'' events. For breeder program reactors, some accidents in this severe category involve spillage of sodium coolant onto concrete protected by a steel liner. Heat transfer through the liner heats the concrete, causing a part of the mixing water and other gases to be driven off. These gases would add to pressure in the containment atmosphere, and the water vapor can form hydrogen if it contacts sodium. Evaluations of containment integrity for such postulated accidents will be aided by knowledge of how much water and other gases are released from heated concrete. The report presents results of a research effort at Hanford Engineering Development Laboratory designed to improve understanding of the release of water and gases from heated concrete

Deliberate release of genetically modified plants into the environment in Slovenia

Directory of Open Access Journals (Sweden)

Zlata LUTHAR

2015-11-01

Full Text Available Deliberate release of genetically modified higher plants (GMHPs into the environment in Slovenia is regulated by the Law on the Management of Genetically Modified Organisms (ZRGSO Ur. l. RS 23/2005 and 21/2010, III chapter. For each deliberate release of GMPs into the environment a license issued by the Ministry of Environment and Spatial Planning (MESP must be acquired. The application or notification should contain a very accurate and complex description of the GMP, of the field where it will be released and of wider surroundings or environment. The application consists of Annex 2 with accessories: 1. Part A (technical data for the authorization of deliberate GMP release into the environment; 2. Part B (environmental risk assessment; 3. Application summary in Slovenian and English language for the release of GMP into environment, which is transmitted to Brussels by MESP; 4. Extract from the Land Cadastre of the field to which the GMP will be released. The release procedure runs (till here under the above mentioned Law, which has been in place for several years and which clearly defines that it is possible to release GMP in Slovenia. In the case of GM rice in 2011, the law applied till the site selection of the experiment. Here, the law was not sufficiently taken into account. It was prevailed by the regulation of Farmland and Forest Fund of the Republic of Slovenia and municipal decision, which was stronger than the national law and prevented the cultivation of GM rice in an area that is legally suitable for release of GMO into the environment. Rice is not grown in Slovenia and does not have wild ancestors or close relatives with whom it might mate. Nearest area of cultivation is in neighboring Italy, which is from potentially selected location in Slovenia more than 70 km away.

Information Presentation in Decision and Risk Analysis: Answered, Partly Answered, and Unanswered Questions.

Science.gov (United States)

Keller, L Robin; Wang, Yitong

2017-06-01

For the last 30 years, researchers in risk analysis, decision analysis, and economics have consistently proven that decisionmakers employ different processes for evaluating and combining anticipated and actual losses, gains, delays, and surprises. Although rational models generally prescribe a consistent response, people's heuristic processes will sometimes lead them to be inconsistent in the way they respond to information presented in theoretically equivalent ways. We point out several promising future research directions by listing and detailing a series of answered, partly answered, and unanswered questions. © 2016 Society for Risk Analysis.

Deuterium release from Li-D films exposed to atmospheric gases

Energy Technology Data Exchange (ETDEWEB)

Gasparyan, Yu. M., E-mail: YMGasparyan@mephi.ru [National Research Nuclear University MEPhI (Moscow Engineering Physics Institute), Kashirskoe highway 31, Moscow (Russian Federation); Popkov, A.S.; Krat, S.A.; Pisarev, A.A.; Vasina, Ya. A. [National Research Nuclear University MEPhI (Moscow Engineering Physics Institute), Kashirskoe highway 31, Moscow (Russian Federation); Lyublinski, I.E. [National Research Nuclear University MEPhI (Moscow Engineering Physics Institute), Kashirskoe highway 31, Moscow (Russian Federation); JSC “Red Star”, Electrolitniy proezd 1a, Moscow (Russian Federation); Vertkov, A.V. [JSC “Red Star”, Electrolitniy proezd 1a, Moscow (Russian Federation)

2017-04-15

Highlights: • The major part of deuterium desorbs from Li-D films in a very sharp peak at 670–710 K. • Exposure on air leads to intensive deuterium release from the Li-D film at room temperature. • Interaction with water vapor plays a major role in deuterium release from lithium films in the air. - Abstract: Deuterium release from Li-D films co-deposited on a Mo substrate at room temperature in magnetron discharge was investigated by means of thermal desorption spectroscopy. The deuterium concentration in the films was estimated to be D/Li = (14 ± 4)%. TDS from Li-D films just after co-deposition had a sharp peak at 670–710 K. Exposure of deposited Li-D films in the air at room temperature led to deuterium release. Comparison of release in air, water vapor, nitrogen, and oxygen demonstrated that water plays a major role in deuterium release in the air at low temperatures.

Coupled Physics Environment (CouPE) library - Design, Implementation, and Release

Energy Technology Data Exchange (ETDEWEB)

Mahadevan, Vijay S. [Argonne National Lab. (ANL), Argonne, IL (United States)

2014-09-30

Over several years, high fidelity, validated mono-­physics solvers with proven scalability on peta-­scale architectures have been developed independently. Based on a unified component-­based architecture, these existing codes can be coupled with a unified mesh-­data backplane and a flexible coupling-­strategy-­based driver suite to produce a viable tool for analysts. In this report, we present details on the design decisions and developments on CouPE, an acronym that stands for Coupled Physics Environment that orchestrates a coupled physics solver through the interfaces exposed by MOAB array-­based unstructured mesh, both of which are part of SIGMA (Scalable Interfaces for Geometry and Mesh-­Based Applications) toolkit. The SIGMA toolkit contains libraries that enable scalable geometry and unstructured mesh creation and handling in a memory and computationally efficient implementation. The CouPE version being prepared for a full open-­source release along with updated documentation will contain several useful examples that will enable users to start developing their applications natively using the native MOAB mesh and couple their models to existing physics applications to analyze and solve real world problems of interest. An integrated multi-­physics simulation capability for the design and analysis of current and future nuclear reactor models is also being investigated as part of the NEAMS RPL, to tightly couple neutron transport, thermal-­hydraulics and structural mechanics physics under the SHARP framework. This report summarizes the efforts that have been invested in CouPE to bring together several existing physics applications namely PROTEUS (neutron transport code), Nek5000 (computational fluid-dynamics code) and Diablo (structural mechanics code). The goal of the SHARP framework is to perform fully resolved coupled physics analysis of a reactor on heterogeneous geometry, in order to reduce the overall numerical uncertainty while leveraging

Potential of Phytase-Mediated Iron Release from Cereal-Based Foods: A Quantitative View

Science.gov (United States)

Nielsen, Anne V. F.; Tetens, Inge; Meyer, Anne S.

2013-01-01

The major part of iron present in plant foods such as cereals is largely unavailable for direct absorption in humans due to complexation with the negatively charged phosphate groups of phytate (myo-inositol (1,2,3,4,5,6)-hexakisphosphate). Human biology has not evolved an efficient mechanism to naturally release iron from iron phytate complexes. This narrative review will evaluate the quantitative significance of phytase-catalysed iron release from cereal foods. In vivo studies have shown how addition of microbially derived phytases to cereal-based foods has produced increased iron absorption via enzyme-catalysed dephosphorylation of phytate, indicating the potential of this strategy for preventing and treating iron deficiency anaemia. Despite the immense promise of this strategy and the prevalence of iron deficiency worldwide, the number of human studies elucidating the significance of phytase-mediated improvements in iron absorption and ultimately in iron status in particularly vulnerable groups is still low. A more detailed understanding of (1) the uptake mechanism for iron released from partially dephosphorylated phytate chelates, (2) the affinity of microbially derived phytases towards insoluble iron phytate complexes, and (3) the extent of phytate dephosphorylation required for iron release from inositol phosphates is warranted. Phytase-mediated iron release can improve iron absorption from plant foods. There is a need for development of innovative strategies to obtain better effects. PMID:23917170

Pharmacokinetic comparison of sustained- and immediate-release oral formulations of cilostazol in healthy Korean subjects: a randomized, open-label, 3-part, sequential, 2-period, crossover, single-dose, food-effect, and multiple-dose study.

Science.gov (United States)

Lee, Donghwan; Lim, Lay Ahyoung; Jang, Seong Bok; Lee, Yoon Jung; Chung, Jae Yong; Choi, Jong Rak; Kim, Kiyoon; Park, Jin Woo; Yoon, Hosang; Lee, Jaeyong; Park, Min Soo; Park, Kyungsoo

2011-12-01

A sustained-release (SR) formulation of cilostazol was recently developed in Korea and was expected to yield a lower C(max) and a similar AUC to the immediate-release (IR) formulation. The goal of the present study was to compare the pharmacokinetic profiles of a newly developed SR formulation and an IR formulation of cilostazol after single- and multiple-dose administration and to evaluate the influence of food in healthy Korean subjects. This study was developed as part of a product development project at the request of the Korean regulatory agency. This was a randomized, 3-part, sequential, open-label, 2-period crossover study. Each part consisted of different subjects between the ages of 19 and 55 years. In part 1, each subject received a single dose of SR (200 mg × 1 tablet, once daily) and IR (100 mg × 2 tablets, BID) formulations of cilostazol orally 7 days apart in a fasted state. In part 2, each subject received a single dose of the SR (200 mg × 1 tablet, once daily) formulation of cilostazol 7 days apart in a fasted and a fed state. In part 3, each subject received multiple doses of the 2 formulations for 8 consecutive days 21 days apart. Blood samples were taken for 72 hours after the dose. Cilostazol pharmacokinetics were determined for both the parent drug and its metabolites (OPC-13015 and OPC-13213). Adverse events were evaluated through interviews and physical examinations. Among the 92 enrolled subjects (66 men, 26 women; part 1, n = 26; part 2, n = 26; part 3, n = 40), 87 completed the study. In part 1, all the primary pharmacokinetic parameters satisfied the criterion for assumed bioequivalence both in cilostazol and its metabolites, yielding 90% CI ratios of 0.9624 to 1.2323, 0.8873 to 1.1208, and 0.8919 to 1.1283 for C(max) and 0.8370 to 1.0134, 0.8204 to 0.9807, and 0.8134 to 0.9699 for AUC(0-last) of cilostazol, OPC-13015, and OPC-13213, respectively. In part 2, food intake increased C(max) and AUC significantly (P food and 23 with a high

Fission gas release during post irradiation annealing of large grain size fuels from Hinkley point B

International Nuclear Information System (INIS)

Killeen, J.C.

1997-01-01

A series of post-irradiation anneals has been carried out on fuel taken from an experimental stringer from Hinkley Point B AGR. The stringer was part of an experimental programme in the reactor to study the effect of large grain size fuel. Three differing fuel types were present in separate pins in the stringer. One variant of large grain size fuel had been prepared by using an MgO dopant during fuel manufactured, a second by high temperature sintering of standard fuel and the third was a reference, 12μm grain size fuel. Both large grain size variants had similar grain sizes around 35μm. The present experiments took fuel samples from highly rated pins from the stringer with local burn-up in excess of 25GWd/tU and annealed these to temperature of up to 1535 deg. C under reducing conditions to allow a comparison of fission gas behaviour at high release levels. The results demonstrate the beneficial effect of large grain size on release rate of 85 Kr following interlinkage. At low temperatures and release rates there was no difference between the fuel types, but at temperatures in excess of 1400 deg. C the release rate was found to be inversely dependent on the fuel grain size. The experiments showed some differences between the doped and undoped large grains size fuel in that the former became interlinked at a lower temperature, releasing fission gas at an increased rate at this temperature. At higher temperatures the grain size effect was dominant. The temperature dependence for fission gas release was determined over a narrow range of temperature and found to be similar for all three types and for both pre-interlinkage and post-interlinkage releases, the difference between the release rates is then seen to be controlled by grain size. (author). 4 refs, 7 figs, 3 tabs

Fission gas release during post irradiation annealing of large grain size fuels from Hinkley point B

Energy Technology Data Exchange (ETDEWEB)

Killeen, J C [Nuclear Electric plc, Barnwood (United Kingdom)

1997-08-01

A series of post-irradiation anneals has been carried out on fuel taken from an experimental stringer from Hinkley Point B AGR. The stringer was part of an experimental programme in the reactor to study the effect of large grain size fuel. Three differing fuel types were present in separate pins in the stringer. One variant of large grain size fuel had been prepared by using an MgO dopant during fuel manufactured, a second by high temperature sintering of standard fuel and the third was a reference, 12{mu}m grain size fuel. Both large grain size variants had similar grain sizes around 35{mu}m. The present experiments took fuel samples from highly rated pins from the stringer with local burn-up in excess of 25GWd/tU and annealed these to temperature of up to 1535 deg. C under reducing conditions to allow a comparison of fission gas behaviour at high release levels. The results demonstrate the beneficial effect of large grain size on release rate of {sup 85}Kr following interlinkage. At low temperatures and release rates there was no difference between the fuel types, but at temperatures in excess of 1400 deg. C the release rate was found to be inversely dependent on the fuel grain size. The experiments showed some differences between the doped and undoped large grains size fuel in that the former became interlinked at a lower temperature, releasing fission gas at an increased rate at this temperature. At higher temperatures the grain size effect was dominant. The temperature dependence for fission gas release was determined over a narrow range of temperature and found to be similar for all three types and for both pre-interlinkage and post-interlinkage releases, the difference between the release rates is then seen to be controlled by grain size. (author). 4 refs, 7 figs, 3 tabs.

Environmental assessment of the Chernobyl releases in China

International Nuclear Information System (INIS)

Zunsu, H.

1988-01-01

Since Chernobyl accident, China has rapidly developed a program of emergency preparedness for nuclear accidents that the institute of radiation protection assumes the responsibility together with other institutions. For the nuclear power plants in Qinshan and in Daya Bay, a series of emergency preparedness, including the investigation of conditions and feasibility of some principal protective measures are being carried out. The research program includes atmospheric transfer and dispersion, modelling analysis of accident consequence assessment and development of a computer software system for accident consequence prediction. The strategy of China is to well organize all resources and to broaden the international cooperation. The drafting of national emergency regulations and technical guides and the establishment of specialized technical teams are in progress. In China, the accident consequence assessment is based on the specialist experiences from transfer of radioactive effluents in the atmosphere, in water and in ecological system. On May 1986 environmental assessment of the Chernobyl releases in China and environmental monitoring were carried out. Radio-nuclides released from the Chernobyl accident were detectable in all parts of country but the concentrations were very low. The results of the environmental monitoring have been presented. 7 figs., 11 tabs. (author)

Fission product release from nuclear fuel II. Validation of ASTEC/ELSA on analytical and large scale experiments

International Nuclear Information System (INIS)

Brillant, G.; Marchetto, C.; Plumecocq, W.

2013-01-01

Highlights: • A wide range of experiments is presented for the ASTEC/ELSA code validation. • Analytical tests such as AECL, ORNL and VERCORS are considered. • A large-scale experiment, PHEBUS FPT1, is considered. • The good agreement with measurements shows the efficiency of the ASTEC modelling. • Improvements concern the FP release modelling from MOX and high burn-up UO 2 fuels. - Abstract: This article is the second of two articles dedicated to the mechanisms of fission product release from a degraded core. The models of fission product release from nuclear fuel in the ASTEC code have been described in detail in the first part of this work (Brillant et al., this issue). In this contribution, the validation of ELSA, the module of ASTEC that deals with fission product and structural material release from a degraded core, is presented. A large range of experimental tests, with various temperature and conditions for the fuel surrounding atmosphere (oxidising and reducing), is thus simulated with the ASTEC code. The validation database includes several analytical experiments with both bare fuel (e.g. MCE1 experiments) and cladded fuel (e.g. HCE3, VERCORS). Furthermore, the PHEBUS large-scale experiments are used for the validation of ASTEC. The rather satisfactory comparison between ELSA calculations and experimental measurements demonstrates the efficiency of the analytical models to describe fission product release in severe accident conditions

Estradiol potentiation of gonadotropin-releasing hormone responsiveness in the anterior pituitary is mediated by an increase in gonadotropin-releasing hormone receptors

International Nuclear Information System (INIS)

Menon, M.; Peegel, H.; Katta, V.

1985-01-01

In order to investigate the mechanism by which 17 beta-estradiol potentiates the action of gonadotropin-releasing hormone on the anterior pituitary in vitro, cultured pituitary cells from immature female rats were used as the model system. Cultures exposed to estradiol at concentrations ranging from 10(-10) to 10(-6) mol/L exhibited a significant augmentation of luteinizing hormone release in response to a 4-hour gonadotropin-releasing hormone (10 mumol/L) challenge at a dose of 10(-9) mol/L compared to that of control cultures. The estradiol augmentation of luteinizing hormone release was also dependent on the duration of estradiol exposure. When these cultures were incubated with tritium-labeled L-leucine, an increase in incorporation of radiolabeled amino acid into total proteins greater than that in controls was observed. A parallel stimulatory effect of estradiol on iodine 125-labeled D-Ala6 gonadotropin-releasing hormone binding was observed. Cultures incubated with estradiol at different concentrations and various lengths of time showed a significant increase in gonadotropin-releasing hormone binding capacity and this increase was abrogated by cycloheximide. Analysis of the binding data showed that the increase in gonadotropin-releasing hormone binding activity was due to a change in the number of gonadotropin-releasing hormone binding sites rather than a change in the affinity. These results suggest that (1) estradiol treatment increases the number of pituitary receptors for gonadotropin-releasing hormone, (2) the augmentary effect of estradiol on luteinizing hormone release at the pituitary level might be mediated, at least in part, by the increase in the number of binding sites of gonadotropin-releasing hormone, and (3) new protein synthesis may be involved in estradiol-mediated gonadotropin-releasing hormone receptor induction

Fluoride-releasing restorative materials and secondary caries.

Science.gov (United States)

Hicks, John; Garcia-Godoy, Franklin; Donly, Kevin; Flaitz, Catherine

2003-03-01

Secondary caries is responsible for 60 percent of all replacement restorations in the typical dental practice. Risk factors for secondary caries are similar to those for primary caries development. Unfortunately, it is not possible to accurately predict which patients are at risk for restoration failure. During the past several decades, fluoride-releasing dental materials have become a part of the dentist's armamentarium. Considerable fluoride is released during the setting reaction and for periods up to eight years following restoration placement. This released fluoride is readily taken up by the cavosurface tooth structure, as well as the enamel and root surfaces adjacent to the restoration. Resistance against caries along the cavosurface and the adjacent smooth surface has been shown in both in vitro and in vivo studies. Fluoride-releasing dental materials provide for improved resistance against primary and secondary caries in coronal and root surfaces. Plaque and salivary fluoride levels are elevated to a level that facilitates remineralization. In addition, the fluoride released to dental plaque adversely affects the growth of lactobacilli and mutans streptococci by interference with bacterial enzyme systems. Fluoride recharging of these dental materials is readily achieved with fluoridated toothpastes, fluoride mouthrinses, and other sources of topical fluoride. This allows fluoride-releasing dental materials to act as intraoral fluoride reservoirs. The improvement in the properties of dental materials with the ability to release fluoride has improved dramatically in the past decade, and it is anticipated that in the near future the vast majority of restorative procedures will employ fluoride-releasing dental materials as bonding agents, cavity liners, luting agents, adhesives for orthodontic brackets, and definitive restoratives.

Characterization of a synthetic bacterial self-destruction device for programmed cell death and for recombinant proteins release

Directory of Open Access Journals (Sweden)

Lupotto Manuel

2011-06-01

Full Text Available Abstract Background Bacterial cell lysis is a widely studied mechanism that can be achieved through the intracellular expression of phage native lytic proteins. This mechanism can be exploited for programmed cell death and for gentle cell disruption to release recombinant proteins when in vivo secretion is not feasible. Several genetic parts for cell lysis have been developed and their quantitative characterization is an essential step to enable the engineering of synthetic lytic systems with predictable behavior. Results Here, a BioBrick™ lysis device present in the Registry of Standard Biological Parts has been quantitatively characterized. Its activity has been measured in E. coli by assembling the device under the control of a well characterized N-3-oxohexanoyl-L-homoserine lactone (HSL -inducible promoter and the transfer function, lysis dynamics, protein release capability and genotypic and phenotypic stability of the device have been evaluated. Finally, its modularity was tested by assembling the device to a different inducible promoter, which can be triggered by heat induction. Conclusions The studied device is suitable for recombinant protein release as 96% of the total amount of the intracellular proteins was successfully released into the medium. Furthermore, it has been shown that the device can be assembled to different input devices to trigger cell lysis in response to a user-defined signal. For this reason, this lysis device can be a useful tool for the rational design and construction of complex synthetic biological systems composed by biological parts with known and well characterized function. Conversely, the onset of mutants makes this device unsuitable for the programmed cell death of a bacterial population.

Presentation and interpretation of field experiments of gaseous UF6 releases in the atmosphere

International Nuclear Information System (INIS)

Crabol, B.; Boulaud, D.; Deville-Cavelin, G.

1992-01-01

An experimental programme concerning the behaviour of UF 6 released in gaseous phase in the atmosphere has been conducted in the years 1986-1989 by the french Atomic Energy Commission and Eurodif. Three field tests have been performed on the CEA/CESTA experimental site. These experiments permitted to get informations about the kinetics of the hydrolysis reaction of the UF 6 , the behaviour of the hydrolysis products in the atmosphere and the granulometry of the solid particles

Presentation and interpretation of field experiments of gaseous UF6 releases in the atmosphere

Energy Technology Data Exchange (ETDEWEB)

Crabol, B.; Boulaud, D.; Deville-Cavelin, G. [CEA Centre d`Etudes de Fontenay-aux-Roses, 92 (France). Dept. de Protection de l`Environnement et des Installations; Geisse, C.; Iacona, L. [EURODIF, 26 - Pierrelatte (France)

1992-12-31

An experimental programme concerning the behaviour of UF{sub 6} released in gaseous phase in the atmosphere has been conducted in the years 1986-1989 by the french Atomic Energy Commission and Eurodif. Three field tests have been performed on the CEA/CESTA experimental site. These experiments permitted to get informations about the kinetics of the hydrolysis reaction of the UF{sub 6}, the behaviour of the hydrolysis products in the atmosphere and the granulometry of the solid particles.

The scaffold protein calcium/calmodulin-dependent serine protein kinase controls ATP release in sensory ganglia upon P2X3 receptor activation and is part of an ATP keeper complex.

Science.gov (United States)

Bele, Tanja; Fabbretti, Elsa

2016-08-01

P2X3 receptors, gated by extracellular ATP, are expressed by sensory neurons and are involved in peripheral nociception and pain sensitization. The ability of P2X3 receptors to transduce extracellular stimuli into neuronal signals critically depends on the dynamic molecular partnership with the calcium/calmodulin-dependent serine protein kinase (CASK). The present work used trigeminal sensory neurons to study the impact that activation of P2X3 receptors (evoked by the agonist α,β-meATP) has on the release of endogenous ATP and how CASK modulates this phenomenon. P2X3 receptor function was followed by ATP efflux via Pannexin1 (Panx1) hemichannels, a mechanism that was blocked by the P2X3 receptor antagonist A-317491, and by P2X3 silencing. ATP efflux was enhanced by nerve growth factor, a treatment known to potentiate P2X3 receptor function. Basal ATP efflux was not controlled by CASK, and carbenoxolone or Pannexin silencing reduced ATP release upon P2X3 receptor function. CASK-controlled ATP efflux followed P2X3 receptor activity, but not depolarization-evoked ATP release. Molecular biology experiments showed that CASK was essential for the transactivation of Panx1 upon P2X3 receptor activation. These data suggest that P2X3 receptor function controls a new type of feed-forward purinergic signaling on surrounding cells, with consequences at peripheral and spinal cord level. Thus, P2X3 receptor-mediated ATP efflux may be considered for the future development of pharmacological strategies aimed at containing neuronal sensitization. P2X3 receptors are involved in sensory transduction and associate to CASK. We have studied in primary sensory neurons the molecular mechanisms downstream P2X3 receptor activation, namely ATP release and partnership with CASK or Panx1. Our data suggest that CASK and P2X3 receptors are part of an ATP keeper complex, with important feed-forward consequences at peripheral and central level. © 2016 International Society for Neurochemistry.

Specialists' meeting on fission product release and transport in gas-cooled reactors. Summary report

Energy Technology Data Exchange (ETDEWEB)

NONE

1985-07-01

The purpose of the Meeting on Fission Product Release and Transport in Gas-Cooled Reactors was to compare and discuss experimental and theoretical results of fission product behaviour in gas-cooled reactors under normal and accidental conditions and to give direction for future development. The technical part of the meeting covered operational experience and laboratory research, activity release, and behaviour of released activity.

Specialists' meeting on fission product release and transport in gas-cooled reactors. Summary report

International Nuclear Information System (INIS)

1985-01-01

The purpose of the Meeting on Fission Product Release and Transport in Gas-Cooled Reactors was to compare and discuss experimental and theoretical results of fission product behaviour in gas-cooled reactors under normal and accidental conditions and to give direction for future development. The technical part of the meeting covered operational experience and laboratory research, activity release, and behaviour of released activity

Fission gas and iodine release measured in IFA-430 up to 15 GWd/t UO2 burnup

International Nuclear Information System (INIS)

Appelhans, A.D.; Turnbull, J.A.; White, R.J.

1983-01-01

The release of fission products from fuel pellets to the fuel-cladding gap is dependent on the fuel temperature, the power (fission rate) and the burnup (fuel structure). As part of the US Nuclear Regulatory Commission's Fuel Behavior Program, EG and G Idaho, Inc., is conducting fission product release studies in the Heavy Boiling Water Reactor in Halden, Norway. This paper presents a summary of the results up to December, 1982. The data cover fuel centerline temperatures ranging from 700 to 1500 0 C for average linear heat ratings of 16 to 35 kW/m. The measurements have been performed for the period between 4.2 and 14.8 GWd/t UO 2 of burnup of the Instrumented Fuel Assembly 430 (IFA-430). The measurement program has been directed toward quantifying the release of the short-lived radioactive noble gases and iodines

A radiolabel-release microwell assay for proteolytic enzymes present in cell culture media

International Nuclear Information System (INIS)

Rucklidge, G.J.; Milne, G.

1990-01-01

A modified method for the measurement of proteolytic enzyme activity in cell culture-conditioned media has been developed. Using the release of 3H-labeled peptides from 3H-labeled gelatin the method is performed in microwell plates. The substrate is insolubilized and attached to the wells by glutaraldehyde treatment, thus eliminating the need for a precipitation step at the end of the assay. The assay is sensitive, reproducible, and convenient for small sample volumes. The effect of different protease inhibitors on activity can be assessed rapidly allowing an early characterization of the enzyme. It can also be adapted to microplate spectrophotometric analysis by staining residual substrate with Coomassie blue

Fuel morphology effects on fission product release

International Nuclear Information System (INIS)

Osetek, D.J.; Hartwell, J.K.; Cronenberg, A.W.

1986-01-01

Results are presented of fission product release behavior observed during four severe fuel damage tests on bundles of UO 2 fuel rods. Transient temperatures up to fuel melting were obtained in the tests that included both rapid and slow cooldown, low and high (36 GWd/t) burnup fuel and the addition of Ag-In-Cd control rods. Release fractions of major fission product species and release rates of noble gas species are reported. Significant differences in release behavior are discussed between heatup and cooldown periods, low and high burnup fuel and long- and short-lived fission products. Explanations for the observed differences are offered that relate fuel morphology changes to the releases

Final technical report; Mercury Release from Organic matter (OM) and OM-Coated Mineral Surfaces

Energy Technology Data Exchange (ETDEWEB)

Aiken, George

2014-10-02

This document is the final technical report for a project designed to address fundamental processes controlling the release of mercury from flood plain soils associated with East Fork Poplar Creek, Tennessee near the U.S. Department of Energy Oak Ridge facility. The report summarizes the activities, findings, presentations, and publications resulting from an award to the U.S. Geological that were part of a larger overall effort including Kathy Nagy (University of Illinois, Chicago, Ill) and Joseph Ryan (University of Colorado, Boulder, CO). The specific charge for the U.S.G.S. portion of the study was to provide analytical support for the larger group effort (Nagy and Ryan), especially with regard to analyses of Hg and dissolved organic matter, and to provide information about the release of mercury from the floodplain soils.

Risk based In Vitro Performance Assessment of Extended Release Abuse Deterrent Formulations

Science.gov (United States)

Xu, Xiaoming; Gupta, Abhay; Al-Ghabeish, Manar; Calderon, Silvia N.; Khan, Mansoor A.

2016-01-01

High strength extended release opioid products, which are indispensable tools in the management of pain, are associated with serious risks of unintentional and potentially fatal overdose, as well as of misuse and abuse that might lead to addiction. The issue of drug abuse becomes increasingly prominent when the dosage forms can be readily manipulated to release a high amount of opioid or to extract the drug in certain products or solvents. One approach to deter opioid drug abuse is by providing novel abuse deterrent formulations (ADF), with properties that may be viewed as barriers to abuse of the product. However, unlike regular extended release formulations, assessment of ADF technologies are challenging, in part due to the great variety of formulation designs available to achieve deterrence of abuse by oral, parenteral, nasal and respiratory routes. With limited prior history or literature information, and lack of compendial standards, evaluation and regulatory approval of these novel drug products become increasingly difficult. The present article describes a risk-based standardized in-vitro approach that can be utilized in general evaluation of abuse deterrent features for all ADF products. PMID:26784976

Intestinal release and uptake of phenolic antioxidant diferulic acids

DEFF Research Database (Denmark)

Andreasen, Mette Findal; Kroon, P A; Williamson, G

2001-01-01

Diferulic acids are potent antioxidants and are abundant structural components of plant cell walls, especially in cereal brans. As such, they are part of many human and animal diets and may contribute to the beneficial effect of cereal brans on health. However, these phenolics are ester-linked to......Diferulic acids are potent antioxidants and are abundant structural components of plant cell walls, especially in cereal brans. As such, they are part of many human and animal diets and may contribute to the beneficial effect of cereal brans on health. However, these phenolics are ester...... in oil. Our study also reveals that human and rat colonic microflora contain esterase activity able to release 5-5-, 8-O-4-, and 8-5-diferulic acids from model compounds and dietary cereal brans, hence providing a mechanism for release of dietary diferulates prior to absorption of the free acids....... In addition, cell-free extracts from human and rat small intestine mucosa exhibited esterase activity towards diferulate esters. Hence, we have shown that esterified diferulates can be released from cereal brans by intestinal enzymes, and that free diferulic acids can be absorbed and enter the circulatory...

Selective release of D and 13C from insoluble organic matter of the Murchison meteorite by impact shock

Science.gov (United States)

Mimura, Koichi; Okamoto, Michioki; Sugitani, Kenichiro; Hashimoto, Shigemasa

2007-03-01

We performed shock-recovery experiments on insoluble organic matter (IOM) purified from the Murchison meteorite, and determined the abundances and isotope ratios of hydrogen and carbon in the shocked IOM sample. We also performed shock experiments on type III kerogen and compared the results of these experiments with the experimental results regarding IOM.The shock selectively released D and 13C from the IOM, while it preferably released H and 12C from the kerogen. The release of these elements from IOM cannot be explained in terms of the isotope effect, whereas their release from kerogen can be explained by this effect. The selective release of heavier isotopes from IOM would be due to its structure, in which D and 13C-enriched parts are present as an inhomogeneity and are weakly attached to the main network. Shock gave rise to a high release of D even at a lower degree of dehydrogenation compared with the stepwise heating of IOM. This effective release of D is probably an inherent result of shock, in which a dynamic high-pressure and high-temperature condition prevails. Thus, shock would effectively control the hydrogen isotope behavior of extraterrestrial organic matter during the evolution of the solar nebula.

Biomechanical consequences of plantar fascial release or rupture during gait. Part II: alterations in forefoot loading.

Science.gov (United States)

Sharkey, N A; Donahue, S W; Ferris, L

1999-02-01

With a model using feet from cadavers, we tested the hypothesis that plantar fascial release or rupture alters the loading environment of the forefoot during the latter half of the stance phase of gait. The model simulated the position and loading environment of the foot at two instants: early in terminal stance immediately after heel-off and late in terminal stance just preceding contralateral heel strike. Eight feet were loaded at both positions by simulated plantar flexor contraction, and the distribution of plantar pressure was measured before and after progressive release of the plantar fascia. Strain in the diaphysis of the second metatarsal was also measured, from which the bending moments and axial force imposed on the metatarsal were calculated. Cutting the medial half of the central plantar fascial band significantly increased peak pressure under the metatarsal heads but had little effect on pressures in other regions of the forefoot or on second metatarsal strain and loading. Dividing the entire central band or completely releasing the plantar fascia from the calcaneus had a much greater effect and caused significant shifts in plantar pressure and force from the toes to beneath the metatarsal heads. These shifts were accompanied by significantly increased strain and bending in the second metatarsal. Complete fasciotomy increased the magnitude of strain in the dorsal aspect of the second metatarsal by more than 80%, suggesting that plantar fascial release or rupture accelerates the accumulation of fatigue damage in these bones. Altered forefoot loading may be a potential complication of plantar fasciotomy.

Possibilities for in-vitro testing of controlled-release parenterals.

OpenAIRE

Kožák, Jan

2014-01-01

The objective of this study was to start with the development of a gel-based medium simulating intramuscular environment for in-vitro drug release testing as an alternative to currently used water-based media. A pork meat was selected as a model of the muscle tissue. At the first part of the study, diffusion rate was proposed as the most determining factor of drug release in gel-based medium. Consequently, the diffusion rate of sodium fluorescein in pork meat was compared with the diffusion r...

Maintaining Healthy Skin -- Part 2

Science.gov (United States)

... and SCI • Depression and SCI • Taking Care of Pressure Sores • Maintaining Healthy Skin (Part I) • Maintaining Healthy Skin ( ... For information on establishing skin tolerance, see our “Pressure Sores” pamphlet.) Pressure releases in a wheelchair can be ...

The finite element part of the LAMCAL program. Elastic-plastic fracture mechanics applications

International Nuclear Information System (INIS)

Lamain, L.G.; Blanckenburg, J.F.G.

1982-01-01

The elastic-plastic FEM code described in this report is the third part of the Lamcal program of which the two other parts for mesh generating and plotting were presented previously. Also this part uses the dynamic core storage. All variables and problem defining data are stored in one common array-SPACE. If all three parts are used together, the same common-SPACE is reused in each part. The lay-out of the complete program is given. J-integral evaluation and plotting can be done immediately in the FE run or afterwards in a post processing run. Post processing is done within the FEM part with a reduced core space. Originally developed as a general code, the use of the present version is mainly focussed on research in the field of the fracture mechanics. Several J-integral routines are available as well as crack growth modelling by node release or stiffness reduction, energy calculations, crack tip elements, etc. In this report the theory is discussed and some sample problems are given. The theory is presented in two parts, the general FEM and the more specific EPFM theory. For the sample problems, a choice has been made to show the accuracy of the program under more or less severe loading conditions

French RSE-M and RCC-MR code appendices for flaw analysis: Presentation of the fracture parameters calculation-Part IV: Cracked elbows

International Nuclear Information System (INIS)

Marie, S.; Chapuliot, S.; Kayser, Y.; Lacire, M.H.; Drubay, B.; Barthelet, B.; Le Delliou, P.; Rougier, V.; Naudin, C.; Gilles, P.; Triay, M.

2007-01-01

Two French nuclear codes include flaw assessment procedures: the RSE-M Code 'Rules for In-service Inspection of Nuclear Power Plant Components' and the RCC-MR code 'Design and Construction rules for mechanical components of FBR nuclear islands and high temperature applications'. Development of analytical methods has been made for the last 10 years through a collaboration between CEA, EDF and AREVA-NP, and through R and D actions involving CEA and IRSN. These activities have led to unification of the common methods of the two codes. The calculation of fracture mechanics parameters, and in particular the stress intensity factor K I and the J integral, has been widely developed for industrial configurations. All the developments have been integrated in the 2005 edition of RSE-M and in 2007 edition of RCC-MR. This series of papers is composed of five parts: the first presents an overview of the methods proposed in the RCC-MR and RSE-M codes. Parts II-IV provide compendia for specific components. The geometries are plates (part II), pipes (part III) and elbows (part IV). Part V presents validation of the methods, with details on their accuracy. This paper presents the stress intensity factor and J calculation for cracked elbows. General data applicable for all defect geometries are first presented, and then, compendia for K I and σ ref calculations are provided for the available defect geometries

THE RADIAL VELOCITY EXPERIMENT (RAVE): THIRD DATA RELEASE

International Nuclear Information System (INIS)

Siebert, A.; Williams, M. E. K.; Siviero, A.; Boeche, C.; Steinmetz, M.; De Jong, R. S.; Enke, H.; Anguiano, B.; Reid, W.; Ritter, A.; Fulbright, J.; Wyse, R. F. G.; Munari, U.; Zwitter, T.; Watson, F. G.; Burton, D.; Cass, C. J. P.; Fiegert, K.; Hartley, M.; Russel, K. S.

2011-01-01

We present the third data release of the RAdial Velocity Experiment (RAVE) which is the first milestone of the RAVE project, releasing the full pilot survey. The catalog contains 83,072 radial velocity measurements for 77,461 stars in the southern celestial hemisphere, as well as stellar parameters for 39,833 stars. This paper describes the content of the new release, the new processing pipeline, as well as an updated calibration for the metallicity based upon the observation of additional standard stars. Spectra will be made available in a future release. The data release can be accessed via the RAVE Web site.

Pressure releasing device for reactor container

International Nuclear Information System (INIS)

Takeda, Mika.

1994-01-01

In the present invention, dose rate to public caused by radioactive rare gases can be decreased. That is, a reactor container contains a reactor pressure vessel incorporating a reactor core. There are disposed a pressure releasing system for releasing the pressure in the reactor pressure vessel to the outside, and a burning device for burning gases released from the pressure releasing system. An exhaustion pipe is disposed to the pressure releasing system. A burning device is disposed to the exhaustion pipe. It is effective to dispose a ventilation port at a portion of the exhaustion pipe upstream of the burning device. In addition, the burning device may preferably be disposed in a multi-stage in the axial direction of the exhaustion pipe. With such procedures, hydrogen in gases discharged along with the release of the pressure in the container is burned. Buoyancy is caused to the exhaustion gases by heat energy upon burning. Since the exhaustion gases can reach a higher level by the buoyancy, the dose rate due to the rare gases can be reduced. (I.S.)

French RSE-M and RCC-MR code appendices for flaw analysis: Presentation of the fracture parameters calculation-Part II: Cracked plates

International Nuclear Information System (INIS)

Marie, S.; Chapuliot, S.; Kayser, Y.; Lacire, M.H.; Drubay, B.; Barthelet, B.; Le Delliou, P.; Rougier, V.; Naudin, C.; Gilles, P.; Triay, M.

2007-01-01

French nuclear codes include flaw assessment procedures: the RSE-M Code 'Rules for In-service Inspection of Nuclear Power Plant Components' and the RCC-MR code 'Design and Construction rules for mechanical components of FBR nuclear islands and high temperature applications'. An important effort of development of these analytical methods has been made for the last 10 years in the frame of a collaboration between CEA, EDF and AREVA-NP, and in the frame of R and D actions involving CEA and IRSN. These activities have led to a unification of the common methods of the two codes. The calculation of fracture mechanics parameters, and in particular the stress intensity factor K I and the J integral, has been widely developed for industrial configurations. All the developments have been integrated in the 2005 edition of RSE-M and in the 2007 edition of RCC-MR. This series of articles is composed of 5 parts: the first part presents an overview of the methods proposed in the RCC-MR and RSE-M codes. Parts II-IV provide compendia for specific components. The geometries are plates (part II), pipes (part III) and elbows (part IV). Finally, part V presents the validation elements of the methods, with details on the process followed for the development and evaluation of the accuracy of the proposed analytical methods. This second article in the series presents all details for the stress intensity factor and J calculations for cracked plates. General data applicable for all defect geometries are first presented, and then, available defect geometries where compendia for K I and σ ref calculation are provided are given

Aerosol material release rates from zircaloy-4 at temperatures from 2000 to 22000C

International Nuclear Information System (INIS)

Mulpuru, S.R.; Wren, D.J.; Rondeau, R.K.

1987-01-01

During some postulated severe accidents involving loss of coolant and loss of emergency coolant injection, the temperatures in a CANDU reactor fuel channel become high enough to cause failure and melting of the Zircaloy fuel cladding. At such high temperatures, vapors of fission products and structural (fuel and cladding) materials will be released into the coolant steam and hydrogen mixture. These vapors will condense as cooler conditions are encountered downstream. The vapors from structural materials are relatively involatile; therefore, they will condense readily into aerosol particles. These particles, in turn, will provide sites for the condensation of the more volatile fission products. The aerosol transport of fission products in the primary heat transport system (PHTS) will thus be influenced by the structural material release rates. As part of an ongoing program to develop predictive tools for aerosol and associated fission product transport through the PHTS, experiments have been conducted to measure the vapor mass release rates of the alloying elements from Zircaloy-4 at high temperatures. The paper presents the results and analysis of these experiments

Fission gas release from ThO2 and ThO2--UO2 fuels (LWBR development program)

International Nuclear Information System (INIS)

Goldberg, I.; Spahr, G.L.; White, L.S.; Waldman, L.A.; Giovengo, J.F.; Pfennigwerth, P.L.; Sherman, J.

1978-08-01

Fission gas release data are presented from 51 fuel rods irradiated as part of the LWBR irradiations test program. The fuel rods were Zircaloy-4 clad and contained ThO 2 or ThO 2 -UO 2 fuel pellets, with UO 2 compositions ranging from 2.0 to 24.7 weight percent and fuel densities ranging from 77.8 to 98.7 percent of theoretical. Rod diameters ranged from 0.25 to 0.71 inches and fuel active lengths ranged from 3 to 84 inches. Peak linear power outputs ranged from 2 to 22 kw/ft for peak fuel burnups up to 56,000 MWD/MTM. Measured fission gas release was quite low, ranging from 0.1 to 5.2 percent. Fission gas release was higher at higher temperature and burnup and was lower at higher initial fuel density. No sensitivity to UO 2 composition was evidenced

Controlled Release Strategies for Bone, Cartilage, and Osteochondral Engineering—Part I: Recapitulation of Native Tissue Healing and Variables for the Design of Delivery Systems

Science.gov (United States)

Santo, Vítor E.; Mano, João F.; Reis, Rui L.

2013-01-01

The potential of growth factors to stimulate tissue healing through the enhancement of cell proliferation, migration, and differentiation is undeniable. However, critical parameters on the design of adequate carriers, such as uncontrolled spatiotemporal presence of bioactive factors, inadequate release profiles, and supraphysiological dosages of growth factors, have impaired the translation of these systems onto clinical practice. This review describes the healing cascades for bone, cartilage, and osteochondral interface, highlighting the role of specific growth factors for triggering the reactions leading to tissue regeneration. Critical criteria on the design of carriers for controlled release of bioactive factors are also reported, focusing on the need to provide a spatiotemporal control over the delivery and presentation of these molecules. PMID:23268651

Fission product release mechanisms and groupings

International Nuclear Information System (INIS)

Iglesia, F.C.; Brito, A.C.; Liu, Y.

1995-01-01

During CANDU postulated accidents the reactor fuel is estimated to be exposed to a variety of conditions. These conditions are dynamic and, during the course of an accident, the fuel may experience a wide range of temperatures and conditions from highly oxidizing to mildly reducing environments. The exposure of the reactor fuel to these environments and temperatures may affect its stoichiometry and release performance. In this paper a review of the important fission product release mechanisms is presented, the results of three out-of-pile experimental programs are summarized, and fission product release groups, for both oxidizing and reducing conditions are proposed. (author)

Tritium release from neutron irradiated beryllium pebbles

Energy Technology Data Exchange (ETDEWEB)

Scaffidi-Argentina, F.; Werle, H. [Forschungszentrum Karlsruhe GmbH Technik und Umwelt (Germany). Inst. fuer Neutronenphysik und Reactortechnik

1998-01-01

One of the most important open issues related to beryllium for fusion applications refers to the kinetics of the tritium release as a function of neutron fluence and temperature. The EXOTIC-7 as well as the `Beryllium` experiments carried out in the HFR reactor in Petten are considered as the most detailed and significant tests for investigating the beryllium response under neutron irradiation. This paper reviews the present status of beryllium post-irradiation examinations performed at the Forschungszentrum Karlsruhe with samples from the above mentioned irradiation experiments, trying to elucidate the tritium release controlling processes. In agreement with previous studies it has been found that release starts at about 500-550degC and achieves a maximum at about 700-750degC. The observed release at about 500-550degC is probably due to tritium escaping from chemical traps, while the maximum release at about 700-750degC is due to tritium escaping from physical traps. The consequences of a direct contact between beryllium and ceramics during irradiation, causing tritium implanting in a surface layer of beryllium up to a depth of about 40 mm and leading to an additional inventory which is usually several times larger than the neutron-produced one, are also presented and the effects on the tritium release are discussed. (author)

Estimation of large early release frequency for Advanced Heavy Water Reactor

International Nuclear Information System (INIS)

Santhosh, T.V.; Thangamani, I.; Shrivastava, A.; Vinod, Gopika; Verma, Vishnu; Vijayan, P.K.

2015-01-01

Level 2 probabilistic safety assessment (PSA) examines severe accidents through a combination of probabilistic and deterministic approaches, in order to determine the release of radionuclides from containment, including the physical processes that are involved in the loss of structural integrity of the reactor core. The probabilistic part focuses on the reliability evaluation of containment systems and the deterministic part focuses on the analysis of the physical processes of an accident (timing and magnitude of radioactivity release), and the response of the containment. The important tasks involved are: (i) grouping and categorization of accident sequences into plant damage states (PDSs) (ii) development of a containment event trees (CETs) (iii) development of CET top event definitions and quantification of failure probabilities, and (iv) assigning the release categories and estimation of large early release frequency (LERF). LERF is defined as the frequency of those accidents leading to rapid, unmitigated release of airborne fission products from the containment to the environment occurring before the effective implementation of offsite emergency response and protective actions such that there is the potential for early health effects. Such accidents generally include unscrubbed releases associated with early containment failure shortly after vessel breach, containment bypass events, and loss of containment isolation. Preliminary assessment of LERF, based on release categorization from qualitative expert judgement, has been carried out and the estimated LERF is found to be 1e-13/yr. The dominant contributors are: (a) LB LOCA with the failure of prompt shutdown coupled with containment isolation failure, (b) containment bypass event from main steam line break outside containment coupled with failure of main steam isolation valves, and (c) LB LOCA with complete failure of emergency core cooling system (ECCS) and loss of moderator cooling

SMA-Based System for Environmental Sensors Released from an Unmanned Aerial Vehicle

Directory of Open Access Journals (Sweden)

Lorenzo Pellone

2017-01-01

Full Text Available In the work at hand, a shape memory alloy (SMA-based system is presented. The system, conceived for releasing environmental sensors from ground or small unmanned aerial vehicles, UAV (often named UAS, unmanned aerial system, is made of a door, integrated into the bottom of the fuselage, a device distributor, operated by a couple of antagonistic SMA springs, and a kinematic chain, to synchronize the deployment operation with the system movement. On the basis of the specifications (weight, available space, energy supply, sensors size, etc., the system design was addressed. After having identified the main system characteristics, a representative mock-up was manufactured, featuring the bottom part of the reference fuselage. Functionality tests were performed to prove the system capability to release the sensors; a detailed characterization was finally carried out, mainly finalized at correlating the kinematic chain displacement with the SMA spring temperature and the supplied electrical power. A comparison between theoretical predictions and experimental outcomes showed good agreement.

An interactive computer model for the assessment of continuous release atmospheric transfers

International Nuclear Information System (INIS)

Pages, P.; Rancillac, F.

1983-05-01

The purpose of the model is to assess air concentrations and soil deposits following a continuous release of gaseous effluents. This is usually part of the problem of assessing the consequences of normal operation of a plant. The atmospheric dispersion model used is the gaussian plume model according to DOURY's scheme. Ground reflexion, the presence of an inversion layer and removal processes (by dry or wet deposition and radioactive decay type) are taken into account. Air and ground concentrations are computed around the release point according to an arbitrary grid with spatial coordinates and accounting for annual frequencies of meteorological conditions. The methodology is presented in detail and assumptions are clearly stated. A conversational structured computer program has been set up in APL which allows to get results easily and to test their sensitivity to various assumptions concerning both input data and model parameters. As an example an application of the model with real data and results is given [fr

Structural and functional analysis of a FeoB A143S G5 loop mutant explains the accelerated GDP release rate.

Science.gov (United States)

Guilfoyle, Amy P; Deshpande, Chandrika N; Vincent, Kimberley; Pedroso, Marcelo M; Schenk, Gerhard; Maher, Megan J; Jormakka, Mika

2014-05-01

GTPases (G proteins) hydrolyze the conversion of GTP to GDP and free phosphate, comprising an integral part of prokaryotic and eukaryotic signaling, protein biosynthesis and cell division, as well as membrane transport processes. The G protein cycle is brought to a halt after GTP hydrolysis, and requires the release of GDP before a new cycle can be initiated. For eukaryotic heterotrimeric Gαβγ proteins, the interaction with a membrane-bound G protein-coupled receptor catalyzes the release of GDP from the Gα subunit. Structural and functional studies have implicated one of the nucleotide binding sequence motifs, the G5 motif, as playing an integral part in this release mechanism. Indeed, a Gαs G5 mutant (A366S) was shown to have an accelerated GDP release rate, mimicking a G protein-coupled receptor catalyzed release state. In the present study, we investigate the role of the equivalent residue in the G5 motif (residue A143) in the prokaryotic membrane protein FeoB from Streptococcus thermophilus, which includes an N-terminal soluble G protein domain. The structure of this domain has previously been determined in the apo and GDP-bound states and in the presence of a transition state analogue, revealing conformational changes in the G5 motif. The A143 residue was mutated to a serine and analyzed with respect to changes in GTPase activity, nucleotide release rate, GDP affinity and structural alterations. We conclude that the identity of the residue at this position in the G5 loop plays a key role in the nucleotide release rate by allowing the correct positioning and hydrogen bonding of the nucleotide base. © 2014 FEBS.

Methodology of external exposure calculation for reuse of conditional released materials from decommissioning - 59138

International Nuclear Information System (INIS)

Ondra, Frantisek; Vasko, Marek; Necas, Vladimir

2012-01-01

The article presents methodology of external exposure calculation for reuse of conditional released materials from decommissioning using VISIPLAN 3D ALARA planning tool. Production of rails has been used as an example application of proposed methodology within the CONRELMAT project. The article presents a methodology for determination of radiological, material, organizational and other conditions for conditionally released materials reuse to ensure that workers and public exposure does not breach the exposure limits during scenario's life cycle (preparation, construction and operation of scenario). The methodology comprises a proposal of following conditions in the view of workers and public exposure: - radionuclide limit concentration of conditionally released materials for specific scenarios and nuclide vectors, - specific deployment of conditionally released materials eventually shielding materials, workers and public during the scenario's life cycle, - organizational measures concerning time of workers or public stay in the vicinity on conditionally released materials for individual performed scenarios and nuclide vectors. The above mentioned steps of proposed methodology have been applied within the CONRELMAT project. Exposure evaluation of workers for rail production is introduced in the article as an example of this application. Exposure calculation using VISIPLAN 3D ALARA planning tool was done within several models. The most exposed profession for scenario was identified. On the basis of this result, an increase of radionuclide concentration in conditional released material was proposed more than two times to 681 Bq/kg without no additional safety or organizational measures being applied. After application of proposed safety and organizational measures (additional shielding, geometry changes and limitation of work duration) it is possible to increase concentration of radionuclide in conditional released material more than ten times to 3092 Bq/kg. Storage

Site release in the decommissioning of nuclear installations

International Nuclear Information System (INIS)

Revilla, Jose Luis; Sanz, Maria Teresa; Marugan, Inmaculada; Simon, Inmaculada; Martin, Manuel; Solis, Susana; Sterling, Agustina

2008-01-01

Spanish regulatory framework for the decommissioning process of a nuclear facility ends up with a decommission statement, which releases the licence-holder of the facility from its responsibilities as an operator. It also establishes -where a restricted site release applies- the appropriate future use restrictions, and the responsible of both maintaining such restrictions and ensuring their compliance. Releasing a site implies eliminating all radiological monitoring. The Regulations, however, did not specify either the radiological conditions to be met for the site to be released, or the possibility of a partial release -with or without restrictions-. In case of restricted site release, the Regulations did not specify either the required criteria for such a release. This paper presents the main features of the Safety Instruction IS-13 'Radiological criteria for the release of nuclear facilities sites' issued recently by the Spanish Nuclear Safety Council as a new specific regulation. This Safety Instruction establishes the requirements and conditions for the release of nuclear facility sites, that is, radiological criteria on the effective dose to the public, partial release of nuclear facility sites and restricted release of nuclear facility sites. (author).

Metallic fission product releases from HTR-spherical fuel elements

International Nuclear Information System (INIS)

Helmbold, M.; Amian, W.; Stoever, D.; Hecker, R.

1978-01-01

Fission product releases from fuel determines to a large extent the feasibility of a special reactor concept. Basic data describing the diffusion behaviour from coated particle fuel are presented concerning isotopes Cs 137 , Sr 90 and Agsup(110m). Taking into account these data for typical 3000MWth plants release calculations are performed. Sensitive release parameters could be defined and the results show low release figures for all the considered reactor concepts. (author)

Modelling of fission product release behavior from HTR spherical fuel elements under accident conditions

International Nuclear Information System (INIS)

Verfondern, K.; Mueller, D.

1991-01-01

Computer codes for modelling the fission product release behavior of spherical fuel elements for High Temperature Reactors (HTR) have been developed for the purpose of being used in risk analyses for HTRs. An important part of the validation and verification procedure for these calculation models is the theoretical investigation of accident simulation experiments which have been conducted in the KueFA test facility in the Hot Cells at KFA. The paper gives a presentation of the basic modeling and the calculational results of fission product release from modern German HTR fuel elements in the temperature range 1600-1800 deg. C using the TRISO coated particle failure model PANAMA and the diffusion model FRESCO. Measurements of the transient release behavior for cesium and strontium and of their concentration profiles after heating have provided informations about diffusion data in the important retention barriers of the fuel: silicon carbide and matrix graphite. It could be shown that the diffusion coefficients of both cesium and strontium in silicon carbide can significantly be reduced using a factor in the range of 0.02 - 0.15 compared to older HTR fuel. Also in the development of fuel element graphite, a tendency towards lower diffusion coefficients for both nuclides can be derived. Special heating tests focussing on the fission gases and iodine release from the matrix contamination have been evaluated to derive corresponding effective diffusion data for iodine in fuel element graphite which are more realistic than the iodine transport data used so far. Finally, a prediction of krypton and cesium release from spherical fuel elements under heating conditions will be given for fuel elements which at present are irradiated in the FRJ2, Juelich, and which are intended to be heated at 1600/1800 deg. C in the KueFA furnace in near future. (author). 7 refs, 11 figs

The value of bladder filling in addition to manual elevation of presenting fetal part in cases of cord prolapse.

Science.gov (United States)

Bord, Ilia; Gemer, Ofer; Anteby, Eyal Y; Shenhav, Simon

2011-05-01

To compare perinatal outcome of deliveries complicated by cord prolapse between cases in which bladder filling was performed in addition to supporting presenting part and cases where only support was employed. A retrospective review of 44 deliveries complicated by prolapse occurring after admission was made. The first group included 29 patients who were rushed to a cesarean section with doctor's hand inside the vagina pushing the presenting part. The second group of 15 patients, included women whose bladder was filled with 500 cc of normal saline in addition to manual support. Time to delivery was similar in the first and second group (19.7 ± 9.46 and 21.6 ± 11.9, P = 0.57; respectively) as well as the mean neonatal pH values (7.28 ± 0.09 and 7.26 ± 0.07, P = 0.55; respectively). There was no significant difference in proportion of neonates with an Apgar score of less than 7 between the two arms. The addition of bladder filling to further displace the presenting part did not improve the neonatal outcome which was not compromised regardless of the measures employed.

Medicare Program; Revisions to Payment Policies Under the Physician Fee Schedule and Other Revisions to Part B for CY 2017; Medicare Advantage Bid Pricing Data Release; Medicare Advantage and Part D Medical Loss Ratio Data Release; Medicare Advantage Provider Network Requirements; Expansion of Medicare Diabetes Prevention Program Model; Medicare Shared Savings Program Requirements. Final rule.

Science.gov (United States)

2016-11-15

This major final rule addresses changes to the physician fee schedule and other Medicare Part B payment policies, such as changes to the Value Modifier, to ensure that our payment systems are updated to reflect changes in medical practice and the relative value of services, as well as changes in the statute. This final rule also includes changes related to the Medicare Shared Savings Program, requirements for Medicare Advantage Provider Networks, and provides for the release of certain pricing data from Medicare Advantage bids and of data from medical loss ratio reports submitted by Medicare health and drug plans. In addition, this final rule expands the Medicare Diabetes Prevention Program model.

Fission product release mechanisms and groupings

Energy Technology Data Exchange (ETDEWEB)

Iglesia, F C; Brito, A C; Liu, Y [Ontario Hydro, Toronto, ON (Canada); and others

1996-12-31

During CANDU postulated accidents the reactor fuel is estimated to be exposed to a variety of conditions. These conditions are dynamic and, during the course of an accident, the fuel may experience a wide range of temperatures and conditions from highly oxidizing to mildly reducing environments. The exposure of the reactor fuel to these environments and temperatures may affect its stoichiometry and release performance. In this paper a review of the important fission product release mechanisms is presented, the results of three out-of-pile experimental programs are summarized, and fission product release groups, for both oxidizing and reducing conditions are proposed. (author) 92 refs., 6 tabs.

Kinetics of potassium release in sweet potato cropped soils: a case study in the highlands of Papua New Guinea

Science.gov (United States)

Rajashekhar Rao, B. K.

2015-02-01

The present study attempts to employ potassium (K) release parameters to identify soil-quality degradation due to changed land use patterns in sweet potato (Ipomoea batatas (L.) Lam) farms of the highlands of Papua New Guinea. Rapid population increase in the region increased pressure on the land to intensify subsistence production mainly by reducing fallow periods. Such continuous cropping practice coupled with lack of K fertilization practices could lead to a rapid loss of soil fertility and soil-resource degradation. The study aims to evaluate the effects of crop intensification on the K-release pattern and identify soil groups vulnerable to K depletion. Soils with widely differing exchangeable and non-exchangeable K contents were sequentially extracted for periods between 1 and 569 h in 0.01 M CaCl2, and K-release data were fitted to four mathematical models: first order, power, parabolic diffusion and Elovich equations. Results showed two distinct parts in the K-release curves, and 58-80% of total K was released to solution phase within 76 h (first five extractions) with 20-42% K released in the later parts (after 76 h). Soils from older farms that were subjected to intensive and prolonged land use showed significantly (P farms recently brought to cultivation (new farms). Among the four equations, first-order and power equations best described the K-release pattern; the constant b, an index of K-release rates, ranged from 0.005 to 0.008 mg kg-1 h-1 in the first-order model and was between 0.14 and 0.83 mg kg-1 h-1 in the power model for the soils. In the non-volcanic soils, model constant b values were significantly (P < 0.05) higher than the volcanic soils, thus indicating the vulnerability of volcanic soils to K deficiency. The volcanic soils cropped for several crop cycles need immediate management interventions either through improved fallow management or through mineral fertilizers plus animal manures to sustain productivity.

Interleukin-6 release from the human brain during prolonged exercise

DEFF Research Database (Denmark)

Nybo, Lars; Nielsen, Bodil; Pedersen, Bente Klarlund

2002-01-01

Interleukin (IL)-6 is a pleiotropic cytokine, which has a variety of physiological roles including functions within the central nervous system. Circulating IL-6 increases markedly during exercise, partly due to the release of IL-6 from the contracting skeletal muscles, and exercise-induced IL-6 m...... influence of hyperthermia. In conclusion, IL-6 is released from the brain during prolonged exercise in humans and it appears that the duration of the exercise rather than the increase in body temperature dictates the cerebral IL-6 response....... in the brain at rest or after 15 min of exercise, but a small release of IL-6 was observed after 60 min of exercise in the first bout (0.06 +/- 0.03 ng min(-1)). This release of IL-6 from the brain was five-fold greater at the end of the second bout (0.30 +/- 0.08 ng min(-1); P

Neutralization method for a hydrofluoric acid release

International Nuclear Information System (INIS)

Williams, D.L.; Deacon, L.E.

1976-01-01

A laboratory investigation of methods for neutralizing a release at the hydrofluoric acid tank farm at the Portsmouth Gaseous Diffusion Plant has revealed that the best neutralization method incorporates the use of a lime/water slurry. In this method, settling of suspended solids in the liquid is enhanced by the application of sodium dodecyl sulfate, which causes immediate flocculation and settling. Dilution and expulsion of the supernatant liquid above the flocculated solids result in an effluent which meets the one part per million fluoride limit established by the U.S. Environmental Protection Agency. A fluoride specific ion electrode is used to determine fluoride concentration. This method presently is being adapted for use in the hydrofluoric acid tank farm and is being considered for use at the plant's fluorine generation facility. It could be adapted for use in any facility that contains fluoride in aqueous solution

Development of novel small molecules for imaging and drug release

Science.gov (United States)

Cao, Yanting

Small organic molecules, including small molecule based fluorescent probes, small molecule based drugs or prodrugs, and smart multifunctional fluorescent drug delivery systems play important roles in biological research, drug discovery, and clinical practices. Despite the significant progress made in these fields, the development of novel and diverse small molecules is needed to meet various demands for research and clinical applications. My Ph.D study focuses on the development of novel functional molecules for recognition, imaging and drug release. In the first part, a turn-on fluorescent probe is developed for the detection of intracellular adenosine-5'-triphosphate (ATP) levels based on multiplexing recognitions. Considering the unique and complicated structure of ATP molecules, a fluorescent probe has been implemented with improved sensitivity and selectivity due to two synergistic binding recognitions by incorporating of 2, 2'-dipicolylamine (Dpa)-Zn(II) for targeting of phospho anions and phenylboronic acid group for cis-diol moiety. The novel probe is able to detect intracellular ATP levels in SH-SY5Y cells. Meanwhile, the advantages of multiplexing recognition design concept have been demonstrated using two control molecules. In the second part, a prodrug system is developed to deliver multiple drugs within one small molecule entity. The prodrug is designed by using 1-(2-nitrophenyl)ethyl (NPE) as phototrigger, and biphenol biquaternary ammonium as the prodrug. With controlled photo activation, both DNA cross-linking agents mechlorethamine and o-quinone methide are delivered and released at the preferred site, leading to efficient DNA cross-links formation and cell death. The prodrug shows negligible cytotoxicity towards normal skin cells (Hekn cells) with and without UV activation, but displays potent activity towards cancer cells (HeLa cells) upon UV activation. The multiple drug release system may hold a great potential for practical application. In the

14 CFR Appendix I to Part 417 - Methodologies for Toxic Release Hazard Analysis and Operational Procedures

Science.gov (United States)

2010-01-01

... Quotient/Hazard Index (HQ/HI) formulation to determine the toxic concentration threshold for mixtures of... cloud center of mass altitude. (vi) Worst case initial source term assuming instantaneous release of...

Containment and release management applied to a PWR ice condenser plant

International Nuclear Information System (INIS)

Lehner, J.; Neogy, P.

1991-01-01

As part of a US Nuclear Regulatory Commission program focusing on the accident management capabilities of operating nuclear plants, Brookhaven National Laboratory (BNL) is carrying out a series of studies of containment and release management (CRM) for each of the five containment types used in US commercial power plants. The purpose of CRM is to maintain the integrity of the containment as long as possible following a severe accident and minimize the release of radioactivity to the environment

Understanding and Predicting the Process of Software Maintenance Releases

Science.gov (United States)

Basili, Victor; Briand, Lionel; Condon, Steven; Kim, Yong-Mi; Melo, Walcelio L.; Valett, Jon D.

1996-01-01

One of the major concerns of any maintenance organization is to understand and estimate the cost of maintenance releases of software systems. Planning the next release so as to maximize the increase in functionality and the improvement in quality are vital to successful maintenance management. The objective of this paper is to present the results of a case study in which an incremental approach was used to better understand the effort distribution of releases and build a predictive effort model for software maintenance releases. This study was conducted in the Flight Dynamics Division (FDD) of NASA Goddard Space Flight Center(GSFC). This paper presents three main results: 1) a predictive effort model developed for the FDD's software maintenance release process; 2) measurement-based lessons learned about the maintenance process in the FDD; and 3) a set of lessons learned about the establishment of a measurement-based software maintenance improvement program. In addition, this study provides insights and guidelines for obtaining similar results in other maintenance organizations.

Presentation and interpretation of field experiments of gaseous UF{sub 6} releases in the atmosphere

Energy Technology Data Exchange (ETDEWEB)

Crabol, B.; Boulaud, D.; Deville-Cavelin, G. [CEA/Inst. de Protection et de Surete Nucleaire, Dept. de Protection de l' Environnement et des Installations, Fontenay-aux-Roses (France); Geisse, C.; Iacona, L. [EURODIF/Production, Site de Tricastin, Pierrelatte Cedex (France)

1992-07-01

An experimental programme concerning the behaviour of UF{sub 6} released in gaseous phase in the atmosphere has been conducted in the years 1986-1989 by the French Atomic Energy Commission and EURODIF. Three field tests have been performed on the CEA/CESTA experimental site. These experiments permitted to get information about the kinetics of the hydrolysis reaction of the UF{sub 6}, the behaviour of the hydrolysis products in the atmosphere and the granulometry of the solid particles. (author)

Limited Releases of Krsko NPP

International Nuclear Information System (INIS)

Breznik, B.; Kovac, A.

2001-01-01

Full text: Krsko Nuclear Power Plant is about 700 MW Pressurised Water Reactor plant located in Slovenia close to the border with Croatia. The authorised limit for the radioactive releases is basically set to 50 μSv effective dose per year to the members of the public. There is also additional limitation of total activities released in a year and concentration. The poster presents the effluents of the year 2000 and evaluated dose referring to the limits and to the natural and other sources of radiation around the plant. (author)

Canadian pollutant releases and transfers : NPRI data 1998

International Nuclear Information System (INIS)

2001-03-01

A large, two-sided fold-out poster showing pollution hotspots throughout Canada, has been released by the Canadian Institute for Environmental Law and Policy (CIELAP). The poster is based on the maps and tables of the National Pollutant Release Inventory (NPRI) 1998. It presents the top on-site releases and off-site transfers of pollutants by facilities across Canada, and provides a summary of releases, transfers and recycling of pollutants by province. The map depicts the facilities with the five largest quantities of individual pollutants released to each medium, i. e. water, air, land, underground. The crude oil and gas, other utilities, primary metal, paper and chemical industrial sectors are responsible for the largest on-site releases, while the business services, fabricated metal. primary metal and chemical industrial sectors account for the largest off-site transfers. Twenty-five of the 176 substances whose releases and transfers are reported under the NPRI are classified as 'toxic' or 'carcinogenic'. tabs., maps

Performance evaluation of the Scent Transfer Unit (STU-100) for organic compound collection and release.

Science.gov (United States)

Eckenrode, Brian A; Ramsey, Scott A; Stockham, Rex A; Van Berkel, Gary J; Asano, Keiji G; Wolf, Dennis A

2006-07-01

The Scent Transfer Unit (STU-100) is a portable vacuum that uses airflow through a sterile gauze pad to capture a volatiles profile over evidentiary items for subsequent canine presentation to assist law enforcement personnel. This device was evaluated to determine its ability to trap and release organic compounds at ambient temperature under controlled laboratory conditions. Gas chromatography-mass spectrometry (GC-MS) analyses using a five-component volatiles mixture in methanol injected directly into a capture pad indicated that compound release could be detected initially and 3 days after the time of collection. Additionally, 15 compounds of a 39-component toxic organic gaseous mixture (10-1000 parts per billion by volume [p.p.b.(v)]) were trapped, released, and detected in the headspace of a volatiles capture pad after being exposed to this mixture using the STU-100 with analysis via GC-MS. Component release efficiencies at ambient temperature varied with the analyte; however, typical values of c. 10% were obtained. Desorption at elevated temperatures of reported human odor/scent chemicals and colognes trapped by the STU-100 pads was measured and indicated that the STU-100 has a significant trapping efficiency at ambient temperature. Multivariate statistical analysis of subsequent mass spectral patterns was also performed.

Implementation of multimode release criteria and dose standard alternatives

International Nuclear Information System (INIS)

Klett, R.

1993-01-01

The current standard that regulates the disposal of high-level radioactive wastes (HLW) and transuranic (TRU) wastes evaluates the cumulative risk of all repositories with a single derived set of generic release limits. This paper reviews the technical basis, attributes, and deficiencies of the present approach and two alternative modifications and extensions. The alternatives are the multimode release limits applied at the point of release and a dose standard alternative suggested at the first Electric Power Research Institute (EPRI) waste disposal workshop. Methods of developing and applying the alternatives are presented and some suggestions are given for incorporating them in the standards

Reporting releases of hazardous substances under CERCLA and EPCRA

International Nuclear Information System (INIS)

Dailey, R.

1990-04-01

Several federal environmental laws requires that ''release of hazardous substances to the environment'' above certain threshold amounts -- Reportable Quantities or RQs -- be reported. Current and proposed regulations under these statutes are unclear and make full compliance difficult. Nevertheless, failure to comply could result in civil or criminal penalties. In response to questions raised by several DOE Field Elements, this Information Brief is part of a series that will provide updated information on this and other CERCLA issues. The Environmental Guidance Division (EH-231) has responded to those questions relating the reporting of releases for which EPA has a clearly articulated position. EPA's position on other questions raised by Field Elements has been equivocal; DOE is working with EPA to resolve these outstanding issues. Additional information briefs on reporting releases will be issued as a clear position is defined

Energy storage and release of prosthetic feet. Part 1: biomechanical analysis related to user benefits

NARCIS (Netherlands)

Postema, K.; Hermens, Hermanus J.; de Vries, J.; de Vries, J.; Koopman, Hubertus F.J.M.; Eisma, W.H.

1997-01-01

The energy storing and releasing behaviour of 2 energy storing feet (ESF) and 2 conventional prosthetic feet (CF) were compared (ESF: Otto Bock Dynamic Pro and Hanger Quantum; CF: Otto Bock Multi Axial and Otto Bock Lager). Ten trans-tibial amputees were selected. The study was designed as a

Safety aspects of targets for ADTT: Activity, volatile products, residual heat release

International Nuclear Information System (INIS)

Gai, E.V.; Ignatyuk, A.V.; Lunev, V.P.; Shubin, Yu.N.

1999-01-01

Safety aspects of heavy metal liquid targets for the accelerator driven systems connected with the activity accumulation and residual energy release due to the irradiation with high energy proton beam are discussed. The results obtained for the lead-bismuth target that are under construction in IPPE now in the frame of ISTC Project No. 559 are briefly presented. The calculations and the analysis of the accumulation of the spallation reaction products, activity and energy release at various moments after the accelerator shutdown are presented. The concentrations of the reaction products, the total and partial activities, the activities of volatile products are determined. The contributions of the short-lived nuclides important for the prediction of the facility behaviour in regimes with the accelerator beam trips. The calculations and analysis of the residual energy release due to different decay type have been performed. The conclusions are as follows. The obtained results showed that long lived radioactivity accumulates mainly due to primary nuclear reactions. Secondary reactions are responsible for the production of small number of long-lived isotopes Bi-207, Po-210 and some others, being generated by radiative capture of low energy neutrons. It is possible to make a conclusion that neutrons in the energy range 20 - 800 MeV and protons with energy above 100 MeV give main contribution to the total activity generation although these parts of spectra inside the target give comparatively small contribution to the total flux. The correct consideration of short-lived nuclides contribution is the main problem in the analysis of the target behaviour in the case of short accelerator shutdowns. They make the determining contribution to the both activity and the heat release at the first moments after the accelerator shutdown, creating the intermediate links and additional channels for the long-lived nuclides accumulation chains. The strong dependence of calculated

Heat and mass release for some transient fuel source fires: A test report

International Nuclear Information System (INIS)

Nowlen, S.P.

1986-10-01

Nine fire tests using five different trash fuel source packages were conducted by Sandia National Laboratories. This report presents the findings of these tests. Data reported includes heat and mass release rates, total heat and mass release, plume temperatures, and average fuel heat of combustion. These tests were conducted as a part of the US Nuclear Regulatory Commission sponsored fire safety research program. Data from these tests were intended for use in nuclear power plant probabilistic risk assessment fire analyses. The results were also used as input to a fire test program at Sandia investigating the vulnerability of electrical control cabinets to fire. The fuel packages tested were chosen to be representative of small to moderately sized transient trash fuel sources of the type that would be found in a nuclear power plant. The highest fire intensity encountered during these tests was 145 kW. Plume temperatures did not exceed 820 0 C

Corrosion Tests of LWR Fuels - Nuclide Release

International Nuclear Information System (INIS)

P.A. Finn; Y. Tsai; J.C. Cunnane

2001-01-01

Two BWR fuels [64 and 71 (MWd)/kgU], one of which contained 2% Gd, and two PWR fuels [30 and 45 (MWd)/kgU], are tested by dripping groundwater on the fuels under oxidizing and hydrologically unsaturated conditions for times ranging from 2.4 to 8.2 yr at 90 C. The 99 Tc, 129 I, 137 Cs, 97 Mo, and 90 Sr releases are presented to show the effects of long reaction times and of gadolinium on nuclide release. This investigation showed that the five nuclides at long reaction times have similar fractional release rates and that the presence of 2% Gd reduced the 99 Tc cumulative release fraction by about an order of magnitude over that of a fuel with a similar burnup

Reconcentration of radioactive material released to sanitary sewers in accordance with 10 CFR Part 20

International Nuclear Information System (INIS)

Ainsworth, C.C.; Hill, R.L.; Cantrell, K.J.; Kaplan, D.I.; Norton, M.V.; Aaberg, R.L.; Stetar, E.A.

1994-12-01

The US Nuclear Regulatory Commission (NRC), in accordance with 10 CFR 20, and agreement states, in accordance with state regulations, regulates the discharge of radioactive materials into sanitary sewer systems. A one-year study was conducted by Pacific Northwest Laboratory (PNL) for the NRC to assess whether radioactive materials that are dischared to sanitary sewer systems undergo significant reconcentration within the wastewater treatment plants (WWTP) and to determine the physical and/or chemical processes that may result in radionuclide reconcentration within the WWTPs. The study objectives were addressed by collecting information and data on wastewater treatment, relevant geochemical processes, and individual radionuclide behavior in WWTPs from the open literature, NRC reports, EPA surveys, and interviews with NRC licensees and staff of WWTPs that may be impacted by these discharges. Radionuclide mass balance and removal efficiencies were calculated for WWTPs at Oak Ridge, TN; and Erwin, TN, but were not shown to be reliable since the licensee release data generally underestimated the mass of radionuclide that was ultimately found in the sludge. This disparity may be due, in part, to the fact that data available for use in this study were collected to address regulatory concerns and not to perform mass balance calculations. A limited modeling study showed some promise for predicting radionuclide behavior in WWTPS, however, the general applicability of using these empirical models remains uncertain. With the data and models currently available, it is not possible to quantitatively determine the physical and chemical processes that cause reconcentration or to calculate, a priori, reconcentration factors for specific WWTP unit processes or WWTPs in general

Effect of Food Emulsifiers on Aroma Release

Directory of Open Access Journals (Sweden)

Jia-Jia Li

2016-04-01

Full Text Available This study aimed to determine the influence of different emulsifiers or xanthan-emulsifier systems on the release of aroma compounds. Solid-phase microextraction (SPME and GC-MS were used to study the effects of varying concentrations of xanthan gum, sucrose fatty acid ester, Tween 80 and soybean lecithin on the release of seven aroma compounds. The effects of the emulsifier systems supplemented with xanthan gum on aroma release were also studied in the same way. The results showed varying degrees of influence of sucrose fatty acid ester, soybean lecithin, Tween 80 and xanthan gum on the release of aroma compounds. Compared with other aroma compounds, ethyl acetate was more likely to be conserved in the solution system, while the amount of limonene released was the highest among these seven aroma compounds. In conclusion, different emulsifiers and complexes showed different surface properties that tend to interact with different aroma molecules. The present studies showed that the composition and structure of emulsifiers and specific interactions between emulsifiers and aroma molecules have significant effects on aroma release.

Aspirin Induces Apoptosis through Release of Cytochrome c from Mitochondria

Directory of Open Access Journals (Sweden)

Katja C. Zimmermann

2000-01-01

Full Text Available Nonsteroidal anti-inflammatory drugs (NSAID reduce the risk for cancer, due to their anti proliferative and apoptosis-inducing effects. A critical pathway for apoptosis involves the release of cytochrome c from mitochondria, which then interacts with Apaf-1 to activate caspase proteases that orchestrate cell death. In this study we found that treatment of a human cancer cell line with aspirin induced caspase activation and the apoptotic cell morphology, which was blocked by the caspase inhibitor zVAD-fmk. Further analysis of the mechanism underlying this apoptotic event showed that aspirin induces translocation of Bax to the mitochondria and triggers release of cytochrome c into the cytosol. The release of cytochrome c from mitochondria was inhibited by overexpression of the antiapoptotic protein Bcl-2 and cells that lack Apaf-1 were resistant to aspirin-induced apoptosis. These data provide evidence that the release of cytochrome c is an important part of the apoptotic mechanism of aspirin.

Contribution o the assessment of the environmental risk associated with uranium releases in the Ritord drainage basin

International Nuclear Information System (INIS)

Beaugelin-Seiller, K.; Garnier-Laplace, J.; Gilbin, R.; Della-Vedova, C.

2008-01-01

This document reports the application to aquatic environments and more particularly to the case of a drainage basin of methods of assessment of the environmental risk presented in another report. The objective is to determine the environmental risk related to releases of uranium from ancient mining sites. The method is applied to available data to diagnose a possible chemical and/or radiological risk due to these releases. Should the occasion occurs, probabilistic approaches are used to refine the assessment of the possible risk identified by the screening. After a presentation of the context, the different screening steps are reported: methodology (exposure analysis, effect analysis, and risk characterization), deterministic characterization of the chronic radiological risk, deterministic characterization of the chronic chemical risk. The next part reports the probabilistic assessment of the chemical or radiological risk. In conclusion, the authors indicate actions to be performed to better analyse exposures, and desirable actions to better analyse effects

Idaho National Engineering Laboratory release criteria for decontamination and decommissioning

International Nuclear Information System (INIS)

Dolenc, M.R.; Case, M.J.

1986-01-01

Criteria have been developed for release of Idaho National Engineering Laboratory (INEL) facilities and land areas following decontamination and decommissioning (D and D). Decommissioning release criteria in the form of dose guidelines were proposed by the US Nuclear Regulatory Commission as early as 1980. These criteria were used on an interim basis for INEL D and D projects. However, dose guidelines alone do not adequately cover the criteria necessary to release sites for unrestricted use. In actual practice, other parameters such as pathways analyses, sampling and instrumentation techniques, and implementation procedures are required to develop the basis for unrestricted release of a site. Thus, a rigorous approach for evaluating these other parameters is needed to develop acceptable D and D release criteria. Because of the complex and sensitive nature of the dose and pathways analyses work, a thorough review by experts in those respective fields was desired. Input and support in preparing or reviewing each part of the criteria development task was solicited from several DOE field offices. Experts were identified and contracted to assist in preparing portions of the release criteria, or to serve on a peer-review committee. Thus, the entire release criteria development task was thoroughly reviewed by recognized experts from each DOE field office, to validate technical content of the INEL site-specific document

Flammable gas double shell tank expert elicitation presentations (Part A and Part B)

Energy Technology Data Exchange (ETDEWEB)

Bratzel, D.R.

1998-04-17

This document is a compilation of presentation packages and white papers for the Flammable Gas Double Shell Tank Expert Elicitation Workshop {number_sign}2. For each presentation given by the different authors, a separate section was developed. The purpose for issuing these workshop presentation packages and white papers as a supporting document is to provide traceability and a Quality Assurance record for future reference to these packages.

Flammable gas double shell tank expert elicitation presentations (Part A and Part B)

International Nuclear Information System (INIS)

Bratzel, D.R.

1998-01-01

This document is a compilation of presentation packages and white papers for the Flammable Gas Double Shell Tank Expert Elicitation Workshop number-sign 2. For each presentation given by the different authors, a separate section was developed. The purpose for issuing these workshop presentation packages and white papers as a supporting document is to provide traceability and a Quality Assurance record for future reference to these packages

Idaho National Engineering Laboratory response to the December 13, 1991, Congressional inquiry on offsite release of hazardous and solid waste containing radioactive materials from Department of Energy facilities

International Nuclear Information System (INIS)

Shapiro, C.; Garcia, K.M.; McMurtrey, C.D.; Williams, K.L.; Jordan, P.J.

1992-05-01

This report is a response to the December 13, 1991, Congressional inquiry that requested information on all hazardous and solid waste containing radioactive materials sent from Department of Energy facilities to offsite facilities for treatment or disposal since January 1, 1981. This response is for the Idaho National Engineering Laboratory. Other Department of Energy laboratories are preparing responses for their respective operations. The request includes ten questions, which the report divides into three parts, each responding to a related group of questions. Part 1 answers Questions 5, 6, and 7, which call for a description of Department of Energy and contractor documentation governing the release of waste containing radioactive materials to offsite facilities. ''Offsite'' is defined as non-Department of Energy and non-Department of Defense facilities, such as commercial facilities. Also requested is a description of the review process for relevant release criteria and a list of afl Department of Energy and contractor documents concerning release criteria as of January 1, 1981. Part 2 answers Questions 4, 8, and 9, which call for information about actual releases of waste containing radioactive materials to offsite facilities from 1981 to the present, including radiation levels and pertinent documentation. Part 3 answers Question 10, which requests a description of the process for selecting offsite facilities for treatment or disposal of waste from Department of Energy facilities. In accordance with instructions from the Department of Energy, the report does not address Questions 1, 2, and 3

[Lactose intolerance: past and present. Part 1].

Science.gov (United States)

Buzás, György Miklós

2015-09-20

Lactose intolerance is the most prevalent intestinal malabsorption disorder. After presentation of its history, the author describes the emergence of lactose intolerance during the evolution of species, and the biochemistry of lactose as well as features of human and bacterial lactase enzymes are then described. The unequal distribution of lactose intolerance in different continents and population is discussed, followed by presentation of past and present prevalence data in Hungary. Adult-type hypolactasia is caused by a polymorphism of the MCM6 gene located upstream from the lactase gene on the long arm of the chromosome 2. It can be determined with the polymerase chain reaction. The intestinal symptoms of lactose intolerance are well known, but its extra-intestinal manifestations are less recognised. Invasive diagnostic methods (determination of lactase activity from small intestinal biopsies, lactose tolerance test), are accurate, but have been replaced by the non-invasive methods; their gold standard is the H2 breath test. Genetic testing is being used more and more frequently in Hungary too, and, presumably, the methane breath test will be also available in the near future. Lactose intolerance can be accompanied by inflammatory bowel diseases, coeliac disease and irritable bowel syndrome; it could be established whether this association is causal or not in order to start a correct diet and therapy.

Noble Gas Release Signal as a Precursor to Fracture

Science.gov (United States)

Bauer, S. J.; Lee, H.; Gardner, W. P.

2017-12-01

We present empirical results of rock strain, microfracturing, acoustic emissions, and noble gas release from laboratory triaxial experiments for a granite, basalt, shale and bedded rock salt. Noble gases are released and measured real-time during deformation using mass spectrometry. The gas release represents a precursive signal to macrofracture. Gas release is associated with increased acoustic emissions indicating that microfracturing is required to release gas and create pathways for the gas to be sensed. The gas released depends on initial gas content, pore structure and its evolution during deformation, the deformation amount, matrix permeability, deformation style and the stress/strain history. Gases are released from inter and intracrystalline sites; release rate increases as strain and microfracturing increases. The gas composition depends on lithology, geologic history and age, fluids present, and radioisotope concentrations that affect radiogenic noble gas isotope (e.g. 4He,40Ar) production. Noble gas emission and its relationship to crustal processes such as seismicity and volcanism, tectonic velocities, qualitative estimates of deep permeability, age dating of groundwater, and a signature of nuclear weapon detonation. Our result show that mechanical deformation of crustal materials is an important process controlling gas release from rocks and minerals, and should be considered in techniques which utilize gas release and/or accumulation. We propose using noble gas release to signal rock deformation in boreholes, mines and waste repositories. We postulate each rock exhibits a gas release signature which is microstructure, stress, strain, and/or permanent deformation dependent. Calibration of such relationships, for example relating gas release per rock unit volume to strain may be used to quantify rock deformation and develop predictive models.Sandia National Laboratories is a multimission laboratory managed and operated by National Technology and

Environmental releases for calendar year 1997

International Nuclear Information System (INIS)

Gleckler, B.P.

1998-01-01

This report fulfills the annual environmental release reporting requirements of US Department of Energy (DOE) Order 5400.1. This report provides supplemental information to the Hanford Site Environmental Report (PNNL-11795). The Hanford Site Environmental Report provides an update on the environmental status of the Hanford Site. The sitewide annual report summarizes the degree of compliance with applicable environmental regulations and informs the public concerning the impact of Hanford Site operations on the surrounding environment. Like the Hanford Site Environmental Report, this annual report presents a summary of the environmental releases from facilities and activities managed by the Fluor Daniel Hanford, Incorporated (FDH), and Bechtel Hanford, Incorporated (BHI). In addition to the summary data, this report also includes detailed data on air emissions, liquid effluents, and hazardous substances released to the environment during calendar year 1997. Comprehensive data summaries of air emissions and liquid effluents in 1997 are displayed in Tables ES-1 through ES-5. These tables represent the following: Table ES-1--Radionuclide air emissions data (detailed data on emissions are presented in Section 2.0); Table ES-2--Data on radioactive liquid effluents discharged to the soil (detailed data are presented in Section 3.0); Table ES-3--Radionuclides discharged to the Columbia River (detailed data are presented in Section 3.0); Table ES-4--Nonradioactive air emissions data (detailed data are presented in Section 2.0); Table ES-5--Total Volumes and Flow Rates of 200/600 Area Radioactive Liquid Effluents (detailed data are presented in Section 3.0)

Border cell release

DEFF Research Database (Denmark)

Mravec, Jozef

2017-01-01

Plant border cells are specialised cells derived from the root cap with roles in the biomechanics of root growth and in forming a barrier against pathogens. The mechanism of highly localised cell separation which is essential for their release to the environment is little understood. Here I present...... in situ analysis of Brachypodium distachyon, a model organism for grasses which possess type II primary cell walls poor in pectin content. Results suggest similarity in spatial dynamics of pectic homogalacturonan during dicot and monocot border cell release. Integration of observations from different...... species leads to the hypothesis that this process most likely does not involve degradation of cell wall material but rather employs unique cell wall structural and compositional means enabling both the rigidity of the root cap as well as detachability of given cells on its surface....

An Affirmative Action Program for Ethnic Minorities. Part I: Present Practices and Procedures of Los Rios District.

Science.gov (United States)

Los Rios Community Coll. District, Sacramento, CA.

The components and present status of programs for ethnic minorities at American River, Sacramento City, and Cosumnes River Colleges of the Los Rios Community College District (California) are explained in this Part I of a larger study. The programs aim to enhance minority students' opportunities to succeed in college, provide equal opportunity for…

Sustained-release progesterone vaginal suppositories 1--development of sustained-release granule--.

Science.gov (United States)

Nakayama, Ayako; Sunada, Hisakazu; Okamoto, Hirokazu; Furuhashi, Kaoru; Ohno, Yukiko; Ito, Mikio

2009-02-01

Progesterone (P) is an important hormone for the establishment of pregnancy, and its administration is useful for luteal insufficiency. Considering the problems of commercially available oral and injection drugs, hospital-formulated vaginal suppositories are clinically used. However, since the half-life of P suppositories is short, it is difficult to maintain its constant blood concentration. To sustain drug efficacy and prevent side-effects, we are attempting to develop sustained-release suppositories by examining the degree of sustained-release of active ingredients. In this study, we examined the combinations of granulation methods and release systems for the preparation of sustained-release granules of P, and produced 13 types of sustained-release granules. We also examined the diameter, content, and dissolution of each type of granules, and confirmed that the sustained-release of all types of granules was satisfactory. Among the sustained-release granules, we selected granules with a content and a degree of sustained-release suitable for sustained-release suppositories.

The Ninth Data Release of the Sloan Digital Sky Survey: First Spectroscopic Data from the SDSS-III Baryon Oscillation Spectroscopic Survey

Energy Technology Data Exchange (ETDEWEB)

Ahn, Christopher P.; Alexandroff, Rachael; Allende Prieto, Carlos; Anderson, Scott F.; Anderton, Timothy; Andrews, Brett H.; Aubourg, Éric; Bailey, Stephen; Balbinot, Eduardo; Barnes, Rory; Bautista, Julian; Beers, Timothy C.; Beifiori, Alessandra; Berlind, Andreas A.; Bhardwaj, Vaishali; Bizyaev, Dmitry; Blake, Cullen H.; Blanton, Michael R.; Blomqvist, Michael; Bochanski, John J.; Bolton, Adam S.; Borde, Arnaud; Bovy, Jo; Brandt, W. N.; Brinkmann, J.; Brown, Peter J.; Brownstein, Joel R.; Bundy, Kevin; Busca, N. G.; Carithers, William; Carnero, Aurelio R.; Carr, Michael A.; Casetti-Dinescu, Dana I.; Chen, Yanmei; Chiappini, Cristina; Comparat, Johan; Connolly, Natalia; Crepp, Justin R.; Cristiani, Stefano; Croft, Rupert A. C.; Cuesta, Antonio J.; da Costa, Luiz N.; Davenport, James R. A.; Dawson, Kyle S.; de Putter, Roland; De Lee, Nathan; Delubac, Timothée; Dhital, Saurav; Ealet, Anne; Ebelke, Garrett L.; Edmondson, Edward M.; Eisenstein, Daniel J.; Escoffier, S.; Esposito, Massimiliano; Evans, Michael L.; Fan, Xiaohui; Femenía Castellá, Bruno; Fernández Alvar, Emma; Ferreira, Leticia D.; Filiz Ak, N.; Finley, Hayley; Fleming, Scott W.; Font-Ribera, Andreu; Frinchaboy, Peter M.; García-Hernández, D. A.; Pérez, A. E. García; Ge, Jian; Génova-Santos, R.; Gillespie, Bruce A.; Girardi, Léo; González Hernández, Jonay I.; Grebel, Eva K.; Gunn, James E.; Guo, Hong; Haggard, Daryl; Hamilton, Jean-Christophe; Harris, David W.; Hawley, Suzanne L.; Hearty, Frederick R.; Ho, Shirley; Hogg, David W.; Holtzman, Jon A.; Honscheid, Klaus; Huehnerhoff, J.; Ivans, Inese I.; Ivezić, Željko; Jacobson, Heather R.; Jiang, Linhua; Johansson, Jonas; Johnson, Jennifer A.; Kauffmann, Guinevere; Kirkby, David; Kirkpatrick, Jessica A.; Klaene, Mark A.; Knapp, Gillian R.; Kneib, Jean-Paul; Le Goff, Jean-Marc; Leauthaud, Alexie; Lee, Khee-Gan; Lee, Young Sun; Long, Daniel C.; Loomis, Craig P.; Lucatello, Sara; Lundgren, Britt; Lupton, Robert H.; Ma, Bo; Ma, Zhibo; MacDonald, Nicholas; Mack, Claude E.; Mahadevan, Suvrath; Maia, Marcio A. G.; Majewski, Steven R.; Makler, Martin; Malanushenko, Elena; Malanushenko, Viktor; Manchado, A.; Mandelbaum, Rachel; Manera, Marc; Maraston, Claudia; Margala, Daniel; Martell, Sarah L.; McBride, Cameron K.; McGreer, Ian D.; McMahon, Richard G.; Ménard, Brice; Meszaros, Sz.; Miralda-Escudé, Jordi; Montero-Dorta, Antonio D.; Montesano, Francesco; Morrison, Heather L.; Muna, Demitri; Munn, Jeffrey A.; Murayama, Hitoshi; Myers, Adam D.; Neto, A. F.; Nguyen, Duy Cuong; Nichol, Robert C.; Nidever, David L.; Noterdaeme, Pasquier; Nuza, Sebastián E.; Ogando, Ricardo L. C.; Olmstead, Matthew D.; Oravetz, Daniel J.; Owen, Russell; Padmanabhan, Nikhil; Palanque-Delabrouille, Nathalie; Pan, Kaike; Parejko, John K.; Parihar, Prachi; Pâris, Isabelle; Pattarakijwanich, Petchara; Pepper, Joshua; Percival, Will J.; Pérez-Fournon, Ismael; Pérez-Ràfols, Ignasi; Petitjean, Patrick; Pforr, Janine; Pieri, Matthew M.; Pinsonneault, Marc H.; Porto de Mello, G. F.; Prada, Francisco; Price-Whelan, Adrian M.; Raddick, M. Jordan; Rebolo, Rafael; Rich, James; Richards, Gordon T.; Robin, Annie C.; Rocha-Pinto, Helio J.; Rockosi, Constance M.; Roe, Natalie A.; Ross, Ashley J.; Ross, Nicholas P.; Rossi, Graziano; Rubiño-Martin, J. A.; Samushia, Lado; Sanchez Almeida, J.; Sánchez, Ariel G.; Santiago, Basílio; Sayres, Conor; Schlegel, David J.; Schlesinger, Katharine J.; Schmidt, Sarah J.; Schneider, Donald P.; Schultheis, Mathias; Schwope, Axel D.; Scóccola, C. G.; Seljak, Uros; Sheldon, Erin; Shen, Yue; Shu, Yiping; Simmerer, Jennifer; Simmons, Audrey E.; Skibba, Ramin A.; Skrutskie, M. F.; Slosar, A.; Sobreira, Flavia; Sobeck, Jennifer S.; Stassun, Keivan G.; Steele, Oliver; Steinmetz, Matthias; Strauss, Michael A.; Streblyanska, Alina; Suzuki, Nao; Swanson, Molly E. C.; Tal, Tomer; Thakar, Aniruddha R.; Thomas, Daniel; Thompson, Benjamin A.; Tinker, Jeremy L.; Tojeiro, Rita; Tremonti, Christy A.; Vargas Magaña, M.; Verde, Licia; Viel, Matteo; Vikas, Shailendra K.; Vogt, Nicole P.; Wake, David A.; Wang, Ji; Weaver, Benjamin A.; Weinberg, David H.; Weiner, Benjamin J.; West, Andrew A.; White, Martin; Wilson, John C.; Wisniewski, John P.; Wood-Vasey, W. M.; Yanny, Brian; Yèche, Christophe; York, Donald G.; Zamora, O.; Zasowski, Gail; Zehavi, Idit; Zhao, Gong-Bo; Zheng, Zheng; Zhu, Guangtun; Zinn, Joel C.

2012-11-19

The Sloan Digital Sky Survey III (SDSS-III) presents the first spectroscopic data from the Baryon Oscillation Spectroscopic Survey (BOSS). This ninth data release (DR9) of the SDSS project includes 535,995 new galaxy spectra (median z=0.52), 102,100 new quasar spectra (median z=2.32), and 90,897 new stellar spectra, along with the data presented in previous data releases. These spectra were obtained with the new BOSS spectrograph and were taken between 2009 December and 2011 July. In addition, the stellar parameters pipeline, which determines radial velocities, surface temperatures, surface gravities, and metallicities of stars, has been updated and refined with improvements in temperature estimates for stars with T_eff<5000 K and in metallicity estimates for stars with [Fe/H]>-0.5. DR9 includes new stellar parameters for all stars presented in DR8, including stars from SDSS-I and II, as well as those observed as part of the SDSS-III Sloan Extension for Galactic Understanding and Exploration-2 (SEGUE-2). The astrometry error introduced in the DR8 imaging catalogs has been corrected in the DR9 data products. The next data release for SDSS-III will be in Summer 2013, which will present the first data from the Apache Point Observatory Galactic Evolution Experiment (APOGEE) along with another year of data from BOSS, followed by the final SDSS-III data release in December 2014.

Minimizing lead release levels in secondary smelters slags

International Nuclear Information System (INIS)

Shenkler, E.S.; Graham, S.; Ghosh, R.; Greenhut, V.A.

1991-01-01

Five lead-containing slags and four mattes were analyzed to reveal microstructure, semi-quantitative microchemistry, and phases present. To determine if the slags could be incorporated as a glass so that lead release levels could be stabilized, glass batches were formulated based on slag compositions. Leaching tests showed that all materials that were fritted in a glass batch had lower lead release levels than non-adjusted materials, and all could satisfy EPA test requirements. The mole ratio of glass modifiers to glass formers played an important role in the extent of lead release. Small additions of phosphate to a batch had a significant effect on lowering lead release levels

A new release of the S3M code

International Nuclear Information System (INIS)

Pavlovic, M.; Bokor, J.; Regodic, M.; Sagatova, A.

2015-01-01

This paper presents a new release of the code that contains some additional routines and advanced features of displaying the results. Special attention is paid to the processing of the SRIM range file, which was not included in the previous release of the code. Examples of distributions provided by the S 3 M code for implanted ions in thyroid and iron are presented. (authors)

Role of fission gas release in reactor licensing

International Nuclear Information System (INIS)

1975-11-01

The release of fission gases from oxide pellets to the fuel rod internal voidage (gap) is reviewed with regard to the required safety analysis in reactor licensing. Significant analyzed effects are described, prominent gas release models are reviewed, and various methods used in the licensing process are summarized. The report thus serves as a guide to a large body of literature including company reports and government documents. A discussion of the state of the art of gas release analysis is presented

Fission product release under severe accidental conditions: general presentation of the program and synthesis of VERCORS 1-6 results

International Nuclear Information System (INIS)

Ducros, G.; Malgouyres, P.P.; Kissane, M.; Boulaud, D.; Durin, M.

2001-01-01

The French Nuclear Protection and Safety Institute (IPSN) launched the HEVA-VERCORS program in 1983, in collaboration with Electricite de France (EDF). This program is devoted to the source term of fission products (FP) released from PWR fuel samples during a sequence representative of a severe accident. The analytical experiments are conducted in a shielded hot cell of the LAMA facility of the Grenoble center of CEA (Commissariat a l'Energie Atomique); as simplified tests addressing a limited number of phenomena, they give results complementary to those of the more global in-pile PHEBUS experiments. Six VERCORS tests have been conducted from 1989-1994 with higher fuel temperatures (up to 2600 K) compared with the earlier HEVA tests in order, in particular, to quantify better the release of lower volatile FPs. This paper gives an overview of the experimental facility, a synthesis of FP release from these tests and exhibits, as an example, some specific results of the VERCORS 6 test, performed with high burn-up fuel (60 GWd tU -1 ). The on-going VERCORS HT-RT program, designed to reach fuel liquefaction temperatures, is described before conclusions are drawn

Decision support system for containment and release management

Energy Technology Data Exchange (ETDEWEB)

Oosterhuis, B [Twente Univ., Enschede (Netherlands). Computer Science Dept.

1995-09-01

The Containment and Release Management project was carried out within the Reinforced Concerted Action Programme for Accident Management Support and partly financed by the European Union. In this report a prototype of an accident management support system is presented. The support system integrates several concepts from accident management research, like safety objective trees, severe accident phenomena, calculation models and an emergency response data system. These concepts are provided by the prototype in such a way that the decision making process of accident management is supported. The prototype application is demonstrated by process data taken from a severe accident scenario for a pressurized water reactor (PWR) that was simulated with the thermohydraulic computer program MAAP. The prototype was derived from a decision support framework based on a decision theory. For established and innovative concepts from accident management research it is pointed out in which way these concepts can support accident management and how these concepts can be integrated. This approach is generic in two ways; it applies to both pressurized and boiling water reactors and it applies to both in vessel management and containment and release management. The prototype application was developed in Multimedia Toolbox 3.0 and requires at least a 386 PC with 4 MB memory, 6 MB free disk space and MS Windows 3.1. (orig.).

Decision support system for containment and release management

International Nuclear Information System (INIS)

Oosterhuis, B.

1995-09-01

The Containment and Release Management project was carried out within the Reinforced Concerted Action Programme for Accident Management Support and partly financed by the European Union. In this report a prototype of an accident management support system is presented. The support system integrates several concepts from accident management research, like safety objective trees, severe accident phenomena, calculation models and an emergency response data system. These concepts are provided by the prototype in such a way that the decision making process of accident management is supported. The prototype application is demonstrated by process data taken from a severe accident scenario for a pressurized water reactor (PWR) that was simulated with the thermohydraulic computer program MAAP. The prototype was derived from a decision support framework based on a decision theory. For established and innovative concepts from accident management research it is pointed out in which way these concepts can support accident management and how these concepts can be integrated. This approach is generic in two ways; it applies to both pressurized and boiling water reactors and it applies to both in vessel management and containment and release management. The prototype application was developed in Multimedia Toolbox 3.0 and requires at least a 386 PC with 4 MB memory, 6 MB free disk space and MS Windows 3.1. (orig.)

SNX9 - a prelude to vesicle release.

Science.gov (United States)

Lundmark, Richard; Carlsson, Sven R

2009-01-01

The sorting nexin SNX9 has, in the past few years, been singled out as an important protein that participates in fundamental cellular activities. SNX9 binds strongly to dynamin and is partly responsible for the recruitment of this GTPase to sites of endocytosis. SNX9 also has a high capacity for modulation of the membrane and might therefore participate in the formation of the narrow neck of endocytic vesicles before scission occurs. Once assembled on the membrane, SNX9 stimulates the GTPase activity of dynamin to facilitate the scission reaction. It has also become clear that SNX9 has the ability to activate the actin regulator N-WASP in a membrane-dependent manner to coordinate actin polymerization with vesicle release. In this Commentary, we summarize several aspects of SNX9 structure and function in the context of membrane remodeling, discuss its interplay with various interaction partners and present a model of how SNX9 might work in endocytosis.

Physico-chemical state influences in vitro release profile of curcumin from pectin beads.

Science.gov (United States)

Nguyen, An Thi-Binh; Winckler, Pascale; Loison, Pauline; Wache, Yves; Chambin, Odile

2014-09-01

Curcumin is a polyphenolic compound with diverse effects interesting to develop health benefit products but its formulation in functional foods or in food supplement is hampered by its poor water solubility and susceptibility to alkaline conditions, light, oxidation and heat. Encapsulation of curcumin could be a mean to overcome these difficulties. In this paper, curcumin was encapsulated by ionotropic gelation method in low methoxyl pectin beads associated with different surfactants: Solutol(®), Transcutol(®) and sodium caseinate. After encapsulation, physico-chemical properties of encapsulated curcumin such as its solubility, physical state, tautomeric forms and encapsulation efficiency as well as encapsulation yield were characterized. In vitro dissolution of curcumin from beads displayed different kinetic profiles according to bead composition due to different matrix network. As Solutol(®) was a good solvent for curcumin, the drug was present into amorphous form in these beads inducing a rapid release of curcumin in the simulated digestive fluids. In contrast, drug release was slower from sodium caseinate beads since curcumin was not totally dissolved during the manufacturing process. Moreover, the FLIM studies showed that a part of curcumin was encapsulated in caseinate micelles and that 34% of this drug was in keto form which may delay the curcumin release. The Transcutol beads showed also a slow drug release because of the low curcumin solubility and the high density of the matrix. Copyright © 2014 Elsevier B.V. All rights reserved.

SkyMapper Southern Survey: First Data Release (DR1)

Science.gov (United States)

Wolf, Christian; Onken, Christopher A.; Luvaul, Lance C.; Schmidt, Brian P.; Bessell, Michael S.; Chang, Seo-Won; Da Costa, Gary S.; Mackey, Dougal; Martin-Jones, Tony; Murphy, Simon J.; Preston, Tim; Scalzo, Richard A.; Shao, Li; Smillie, Jon; Tisserand, Patrick; White, Marc C.; Yuan, Fang

2018-02-01

We present the first data release of the SkyMapper Southern Survey, a hemispheric survey carried out with the SkyMapper Telescope at Siding Spring Observatory in Australia. Here, we present the survey strategy, data processing, catalogue construction, and database schema. The first data release dataset includes over 66 000 images from the Shallow Survey component, covering an area of 17 200 deg2 in all six SkyMapper passbands uvgriz, while the full area covered by any passband exceeds 20 000 deg2. The catalogues contain over 285 million unique astrophysical objects, complete to roughly 18 mag in all bands. We compare our griz point-source photometry with Pan-STARRS1 first data release and note an RMS scatter of 2%. The internal reproducibility of SkyMapper photometry is on the order of 1%. Astrometric precision is better than 0.2 arcsec based on comparison with Gaia first data release. We describe the end-user database, through which data are presented to the world community, and provide some illustrative science queries.

Tritium sorption by cement and subsequent release

International Nuclear Information System (INIS)

Ono, F.; Yamawaki, M.

1995-01-01

In a fusion reactor or tritium-handling facilities, contamination of concrete by tritium and subsequent release from it to the reator or experimental room is a matter of problem for safe control of tritium and management of operational environment. In order to evaluate this tritium behavior, interaction of tritiated water with concrete or cement should be clarified. In the present study, HTO sorption and subsequent release from cement were experimentally studied.(1)Sorption experiments were conducted using columns packed with cement particles of different sizes. From the analysis of the breakthrough curve, tritium diffusivity in macropores and microparticles were evaluated.(2)From the short-term tritium release experiments, effective desorption rate constants were evaluated and the effects of temperature and moisture were studied.(3)In the long-term tritium release experiments to 6000h, the tritium release mechanism was found to be composed of three kinds of water: initially from capillary water, and in the second stage from gel water and from the water in the cement crystal.(4)Tritium release behavior by heat treatment to 800 C was studied. A high temperature above 600 C was required for the tritium trapped in the crystal water to be released. (orig.)

Controlled release hydrophilic matrix tablet formulations of isoniazid: design and in vitro studies.

Science.gov (United States)

Hiremath, Praveen S; Saha, Ranendra N

2008-01-01

The aim of the present investigation was to develop oral controlled release matrix tablet formulations of isoniazid using hydroxypropyl methylcellulose (HPMC) as a hydrophilic release retardant polymer and to study the influence of various formulation factors like proportion of the polymer, polymer viscosity grade, compression force, and release media on the in vitro release characteristics of the drug. The formulations were developed using wet granulation technology. The in vitro release studies were performed using US Pharmacopoeia type 1 apparatus (basket method) in 900 ml of pH 7.4 phosphate buffer at 100 rpm. The release kinetics was analyzed using Korsmeyer-Peppas model. The release profiles were also analyzed using statistical method (one-way analysis of variance) and f (2) metric values. The release profiles found to follow Higuchi's square root kinetics model irrespective of the polymer ratio and the viscosity grade used. The results in the present investigation confirm that the release rate of the drug from the HPMC matrices is highly influenced by the drug/HPMC ratio and viscosity grade of the HPMC. Also, the effect of compression force and release media was found to be significant on the release profiles of isoniazid from HPMC matrix tablets. The release mechanism was found to be anomalous non-Fickian diffusion in all the cases. In the present investigation, a series of controlled release formulations of isoniazid were developed with different release rates and duration so that these formulations could further be assessed from the in vivo bioavailability studies. The formulations were found to be stable and reproducible.

A vacuum microgripping tool with integrated vibration releasing capability

Energy Technology Data Exchange (ETDEWEB)

Rong, Weibin; Fan, Zenghua, E-mail: zenghua-fan@163.com; Wang, Lefeng; Xie, Hui; Sun, Lining [State Key Laboratory of Robotics and System, Harbin Institute of Technology, Harbin, Heilongjiang (China)

2014-08-01

Pick-and-place of micro-objects is a basic task in various micromanipulation demands. Reliable releasing of micro-objects is usually disturbed due to strong scale effects. This paper focuses on a vacuum micro-gripper with vibration releasing functionality, which was designed and assembled for reliable micromanipulation tasks. Accordingly, a vibration releasing strategy of implementing a piezoelectric actuator on the vacuum microgripping tool is presented to address the releasing problem. The releasing mechanism was illustrated using a dynamic micro contact model. This model was developed via theoretical analysis, simulations and pull-off force measurement using atomic force microscopy. Micromanipulation experiments were conducted to verify the performance of the vacuum micro-gripper. The results show that, with the assistance of the vibration releasing, the vacuum microgripping tool can achieve reliable release of micro-objects. A releasing location accuracy of 4.5±0.5 μm and a successful releasing rate of around 100% (which is based on 110 trials) were achieved for manipulating polystyrene microspheres with radius of 35–100 μm.

A vacuum microgripping tool with integrated vibration releasing capability

International Nuclear Information System (INIS)

Rong, Weibin; Fan, Zenghua; Wang, Lefeng; Xie, Hui; Sun, Lining

2014-01-01

Pick-and-place of micro-objects is a basic task in various micromanipulation demands. Reliable releasing of micro-objects is usually disturbed due to strong scale effects. This paper focuses on a vacuum micro-gripper with vibration releasing functionality, which was designed and assembled for reliable micromanipulation tasks. Accordingly, a vibration releasing strategy of implementing a piezoelectric actuator on the vacuum microgripping tool is presented to address the releasing problem. The releasing mechanism was illustrated using a dynamic micro contact model. This model was developed via theoretical analysis, simulations and pull-off force measurement using atomic force microscopy. Micromanipulation experiments were conducted to verify the performance of the vacuum micro-gripper. The results show that, with the assistance of the vibration releasing, the vacuum microgripping tool can achieve reliable release of micro-objects. A releasing location accuracy of 4.5±0.5 μm and a successful releasing rate of around 100% (which is based on 110 trials) were achieved for manipulating polystyrene microspheres with radius of 35–100 μm

Magnetic Active Agent Release System (MAARS): evaluation of a new way for a reproducible, externally controlled drug release into the small intestine.

Science.gov (United States)

Dietzel, Christian T; Richert, Hendryk; Abert, Sandra; Merkel, Ute; Hippius, Marion; Stallmach, Andreas

2012-08-10

Human absorption studies are used to test new drug candidates for their bioavailability in different regions of the gastrointestinal tract. In order to replace invasive techniques (e.g. oral or rectal intubation) a variety of externally controlled capsule-based drug release systems has been developed. Most of these use ionizing radiation, internal batteries, heating elements or even chemicals for the localization and disintegration process of the capsule. This embodies potential harms for volunteers and patients. We report about a novel technique called "Magnetic Active Agent Release System" (MAARS), which uses purely magnetic effects for this purpose. In our trial thirteen healthy volunteers underwent a complete monitoring and release procedure of 250 mg acetylsalicylic acid (ASA) targeting the flexura duodenojejunalis and the mid-part of the jejunum. During all experiments MAARS initiated a sufficient drug release and was well tolerated. Beside this we also could show that the absorption of ASA is about two times faster in the more proximal region of the flexura duodenojejunalis with a tmax of 47±13 min compared to the more distal jejunum with tmax values of 100±10 min (p=0.031). Copyright © 2012 Elsevier B.V. All rights reserved.

Dating gasoline releases using ground-water chemical analyses: Case studies

International Nuclear Information System (INIS)

Worthington, M.A.; Perez, E.J.

1993-01-01

This paper presents case studies where geochemical data were analyzed in spatial and temporal relation to documented gasoline releases at typical service station sites. In particular, the authors present ground-water analytical data for sites where (1) the date of the gasoline release is known with a good degree of confidence, (2) the release is confined to a relatively short period of time so as to be considered essentially instantaneous, (3) antecedent geochemical condition are known or can be reasonably expected to have been either unaffected by previous hydrocarbon impacts or minor in comparison to known release events, and (4) where geologic materials can be classified as to structure and composition. The authors' intent is to provide empirical data regarding the hydrogeological fate of certain gasoline components, namely the compounds benzene, toluene, ethylbenzene and xylene isomers (BTEX) and methyl-tertiary-butyl ether (MTBE). Particular emphasis is placed on analysis of gasoline weathering as a means of comparing releases in given hydrogeologic environments. Trends seen in a variety of comparative hydrocarbon compound ratios may provide a basis for evaluating relative release dates

French RSE-M and RCC-MR code appendices for flaw analysis: Presentation of the fracture parameters calculation-Part I: General overview

International Nuclear Information System (INIS)

Marie, S.; Chapuliot, S.; Kayser, Y.; Lacire, M.H.; Drubay, B.; Barthelet, B.; Le Delliou, P.; Rougier, V.; Naudin, C.; Gilles, P.; Triay, M.

2007-01-01

Two French nuclear codes include flaw assessment procedures: the RSE-M code 'Rules for In-service Inspection of Nuclear Power Plant Components' and the RCC-MR code 'Design and Construction rules for mechanical components of FBR nuclear islands and high temperature applications'. An important effort of development of these analytical methods has been made for the last 10 years in the frame of a collaboration between CEA, EDF and AREVA-NP, and in the frame of R and D actions involving CEA and IRSN. These activities have led to a unification of the common methods of the two codes. The calculation of fracture mechanics parameters, and in particular the stress intensity factor K I and the J integral, has been widely developed for industrial configurations. All developments have been integrated in the 2005 edition of RSE-M and in the 2007 edition of RCC-MR. This series of articles is composed of five parts: this first one presents an overview of the methods proposed in the RCC-MR and RSE-M codes. Parts II-IV provide compendia for specific components: plates (part II), pipes (part III) and elbows (part IV). Finally, part V presents the validation elements of the methods, with details on the process followed for their development and on evaluation of the accuracy of the proposed analytical methods. This first article of the series presents an overview of the calculation of K I and J in these two codes and describes briefly the defect assessment analyses. Specific details in the Appendix A16 of RCC-MR (LBB procedure and creep analyses) are also introduced in this article

Synthesis and characterization of emamectin-benzoate slow-release microspheres with different surfactants.

Science.gov (United States)

Wang, Yan; Wang, Anqi; Wang, Chunxin; Cui, Bo; Sun, Changjiao; Zhao, Xiang; Zeng, Zhanghua; Shen, Yue; Gao, Fei; Liu, Guoqiang; Cui, Haixin

2017-10-06

Pesticide slow-release formulations provide a way to increase the efficiency of active components by reducing the amount of pesticide that needs to be applied. Slow-release formulations also increase the stability and prolong the control effect of photosensitive pesticides. Surfactants are an indispensable part of pesticide formulations, and the choice of surfactant can strongly affect formulation performance. In this study, emamectin-benzoate (EMB) slow-release microspheres were prepared by the microemulsion polymerization method. We explored the effect of different surfactants on the particle size and dispersity of EMB in slow-release microspheres. The results indicated that the samples had uniform spherical shapes with an average diameter of 320.5 ±5.24 nm and good dispersity in the optimal formulation with the polymeric stabilizer polyvinyl alcohol (PVA) and composite non-ionic surfactant polyoxyethylene castor oil (EL-40). The optimal EMB pesticide slow-release microspheres had excellent anti-photolysis performance, stability, controlled release properties, and good leaf distribution. These results demonstrated that EMB slow-release microspheres are an attractive candidate for improving pesticide efficacy and prolonging the control effect of EMB in the environment.

Development of novel diclofenac potassium controlled release tablets by wet granulation technique and the effect of co-excipients on in vitro drug release rates.

Science.gov (United States)

Shah, Shefaatullah; Khan, Gul Majid; Jan, Syed Umer; Shah, Kifayatullah; Hussain, Abid; Khan, Haroon; Khan, Haroon; Khan, Haroon; Khan, Kamran Ahmad

2012-01-01

The aim of the present study was the formulation and evaluation of controlled release polymeric tablets of Diclofenac Potassium by wet granulation method for the release rate, release pattern and the mechanism involved in drug release. Formulations having three grades of polymer Ethocel (7P; 7FP, 10P, 10FP, 100P, 100FP) in several drugs to polymer ratios (10:3 and 10:1) were compressed into tablets using wet granulation method. Co-excipients were added to some selected formulations to investigate their enhancement effect on in vitro drug release patterns. In vitro drug release studies were performed using USP Method-1 (Rotating Basket method) and Phosphate buffer (pH 7.4) was used as a dissolution medium. The similarities and dissimilarities of release profiles of test formulations with reference standard were checked using f2 similarity factor and f1 dissimilarity factor. Mathematical/Kinetic models were employed to determine the release mechanism and drug release kinetics.

The comparison between limited open carpal tunnel release using direct vision and tunneling technique and standard open carpal tunnel release: a randomized controlled trial study.

Science.gov (United States)

Suppaphol, Sorasak; Worathanarat, Patarawan; Kawinwongkovit, Viroj; Pittayawutwinit, Preecha

2012-04-01

To compare the operative outcome of carpal tunnel release between limited open carpal tunnel release using direct vision and tunneling technique (group A) with standard open carpal tunnel release (group B). Twenty-eight patients were enrolled in the present study. A single blind randomized control trial study was conducted to compare the postoperative results between group A and B. The study parameters were Levine's symptom severity and functional score, grip and pinch strength, and average two-point discrimination. The postoperative results between two groups were comparable with no statistical significance. Only grip strength at three months follow up was significantly greater in group A than in group B. The limited open carpal tunnel release in the present study is effective comparable to the standard open carpal tunnel release. The others advantage of this technique are better cosmesis and improvement in grip strength at the three months postoperative period.

Fission gas release from fuel at high burnup

International Nuclear Information System (INIS)

Meyer, R.O.; Beyer, C.E.; Voglewede, J.C.

1978-03-01

The release of fission gas from fuel pellets at high burnup is reviewed in the context of the safety analysis performed for reactor license applications. Licensing actions are described that were taken to correct deficient gas release models used in these safety analyses. A correction function, which was developed by the Nuclear Regulatory Commission staff and its consultants, is presented. Related information, which includes some previously unpublished data, is also summarized. The report thus provides guidance for the analysis of high burnup gas release in licensing situations

Release the Prisoners Game

Science.gov (United States)

Van Hecke, Tanja

2011-01-01

This article presents the mathematical approach of the optimal strategy to win the "Release the prisoners" game and the integration of this analysis in a math class. Outline lesson plans at three different levels are given, where simulations are suggested as well as theoretical findings about the probability distribution function and its mean…

French RSE-M and RCC-MR code appendices for flaw analysis: Presentation of the fracture parameters calculation-Part V: Elements of validation

International Nuclear Information System (INIS)

Marie, S.; Chapuliot, S.; Kayser, Y.; Lacire, M.H.; Drubay, B.; Barthelet, B.; Le Delliou, P.; Rougier, V.; Naudin, C.; Gilles, P.; Triay, M.

2007-01-01

French nuclear codes include flaw assessment procedures: the RSE-M Code 'Rules for In-service Inspection of Nuclear Power Plant Components' and the RCC-MR code 'Design and Construction Rules for Mechanical Components of FBR Nuclear Islands and High Temperature Applications'. Development of analytical methods has been made for the last 10 years in the framework of a collaboration between CEA, EDF and AREVA-NP, and by R and D actions involving CEA and IRSN. These activities have led to a unification of the common methods of the two codes. The calculation of fracture mechanics parameters, in particular the stress intensity factor K I and the J integral, has been widely developed for industrial configurations. All the developments have been integrated in the 2005 edition of RSE-M and in 2007 edition of RCC-MR. This series of articles consists of 5 parts: the first part presents an overview of the methods proposed in the RCC-MR and RSE-M codes. Parts II-IV provide the compendia for specific components. The geometries are plates (part II), pipes (part III) and elbows (part IV). This part presents validation of the methods, with details on the process followed for their development and of the evaluation accuracy of the proposed analytical methods

Regulation of gonadotropin-releasing hormone neurons by glucose

Science.gov (United States)

Roland, Alison V.; Moenter, Suzanne M.

2011-01-01

Reproduction is influenced by energy balance, but the physiological pathways mediating their relationship have not been fully elucidated. As the central regulators of fertility, gonadotropin-releasing hormone (GnRH) neurons integrate numerous physiological signals, including metabolic cues. Circulating glucose levels regulate GnRH release and may in part mediate the effects of negative energy balance on fertility. Existing evidence suggests that neural pathways originating in the hindbrain, as well as in the hypothalamic feeding nuclei, transmit information concerning glucose availability to GnRH neurons. Here we review recent evidence suggesting that GnRH neurons may directly sense changes in glucose availability by a mechanism involving adenosine monophosphate-activated protein kinase (AMPK). These findings expand our understanding of how metabolic signaling in the brain regulates reproduction. PMID:21855365

Recoil release of fission products from nuclear fuel

International Nuclear Information System (INIS)

Wise, C.

1985-01-01

An analytical approximation is developed for calculating recoil release from nuclear fuel into gas filled interspaces. This expression is evaluated for a number of interspace geometries and shown to be generally accurate to within about 10% by comparison with numerical calculations. The results are applied to situations of physical interest and it is demonstrated that recoil can be important when modelling fission product release from low temperature CAGR pin failures. Furthermore, recoil can contribute significantly in experiments on low temperature fission product release, particularly where oxidation enhancement of this release is measured by exposing the fuel to CO 2 . The calculations presented here are one way of allowing for this, other methods are suggested. (orig.)

Tritium sorption by cement and subsequent release

International Nuclear Information System (INIS)

Ono, F.; Tanaka, S.; Yamawaki, M.

1994-01-01

In a fusion reactor or tritium handling facilities, contamination of concrete by tritium and subsequent release from it to the reactor or experimental rooms is a matter of problem for safety control of tritium and management of operational environment. In order to evaluate these tritium behavior, interaction of tritiated water with concrete or cement should be clarified. In the present study, HTO sorption and subsequent release from cement were studied by combining various experimental methods. From the basic studies on tritium-cement interactions, it has become possible to evaluate tritium uptake by cement or concrete and subsequent tritium release behavior as well as tritium removing methods from them

Drug release kinetic analysis and prediction of release data via polymer molecular weight in sustained release diltiazem matrices.

Science.gov (United States)

Adibkia, K; Ghanbarzadeh, S; Mohammadi, G; Khiavi, H Z; Sabzevari, A; Barzegar-Jalali, M

2014-03-01

This study was conducted to investigate the effects of HPMC (K4M and K100M) as well as tragacanth on the drug release rate of diltiazem (DLTZ) from matrix tablets prepared by direct compression method.Mechanism of drug transport through the matrices was studied by fitting the release data to the 10 kinetic models. 3 model independent parameters; i. e., mean dissolution time (MDT), mean release rate (MRR) and release rate efficacy (RE) as well as 5 time point approaches were established to compare the dissolution profiles. To find correlation between fraction of drug released and polymer's molecular weight, dissolution data were fitted into two proposed equations.All polymers could sustain drug release up to 10 h. The release data were fitted best to Peppas and Higuchi square root kinetic models considering squared correlation coefficient and mean percent error (MPE). RE and MRR were decreased when polymer to drug ratio was increased. Conversely, t60% was increased with raising polymer /drug ratio. The fractions of drug released from the formulations prepared with tragacanth were more than those formulated using the same amount of HPMC K4M and HPMC K100M.Preparation of DLTZ matrices applying HPMCK4M, HPMC K100M and tragacanth could effectively extend the drug release. © Georg Thieme Verlag KG Stuttgart · New York.

Microspheres prepared with biodegradable PHBV and PLA polymers as prolonged-release system for ibuprofen: in vitro drug release and in vivo evaluation

Directory of Open Access Journals (Sweden)

Giovana Carolina Bazzo

2012-12-01

Full Text Available In this study, poly(hydroxybutyrate-co-hydroxyvalerate (PHBV and poly(l-lactide (PLA microspheres containing ibuprofen were prepared with the aim of prolonging the drug release. The oil-in-water (O/W emulsion solvent evaporation technique was used, varying the polymer ratio. All formulations provided spherical particles with drug crystals on the surface and a porous and rough polymeric matrix when PHBV was used and smooth external surface when prepared with PLA. The in vitro dissolution profiles show that the formulation containing PHBV/PLA at the proportion of 30/70 presented the best results in terms of prolonging the ibuprofen release. The analysis of the concentration of ibuprofen in the blood of rats showed that maximum levels were achieved at between one and two hours after administration of the immediate-release form (pure drug, while the prolonged microspheres led to a small amount of the drug being released within the first two hours and reached the maximum level after six hours of administration. It was concluded that it is possible to prolong the release of ibuprofen through its incorporation into PHBV/PLA microspheres.No presente estudo foram preparadas microesferas de poli(hidroxibutirato-co-hidroxivalerato (PHBV e poli(ácido láctico (PLA com o objetivo de prolongar a liberação do ibuprofeno, utilizado como fármaco modelo. Empregou-se o método de emulsificação e evaporação do solvente óleo em água (O/A, variando-se a proporção entre os polímeros. Todas as formulações originaram partículas esféricas com cristais de fármaco aderidos à superfície externa. As microesferas apresentaram superfície rugosa e porosa, quando o PHBV foi utilizado, e superfície externa lisa, quando preparadas com o PLA. Os perfis de dissolução in vitro evidenciaram que a formulação que continha PHBV/PLA na proporção de 30/70 apresentou melhores resultados para prolongar a liberação do ibuprofeno. Através da análise da concentra

Sol-gel encapsulation for controlled drug release and biosensing

Science.gov (United States)

Fang, Jonathan

The main focus of this dissertation is to investigate the use of sol-gel encapsulation of biomolecules for controlled drug release and biosensing. Controlled drug release has advantages over conventional therapies in that it maintains a constant, therapeutic drug level in the body for prolonged periods of time. The anti-hypertensive drug Captopril was encapsulated in sol-gel materials of various forms, such as silica xerogels and nanoparticles. The primary objective was to show that sol-gel silica materials are promising drug carriers for controlled release by releasing Captopril at a release rate that is within a therapeutic range. We were able to demonstrate desired release for over a week from Captopril-doped silica xerogels and overall release from Captopril-doped silica nanoparticles. As an aside, the antibiotic Vancomycin was also encapsulated in these porous silica nanoparticles and desired release was obtained for several days in-vitro. The second part of the dissertation focuses on immobilizing antibodies and proteins in sol-gel to detect various analytes, such as hormones and amino acids. Sol-gel competitive immunoassays on antibody-doped silica xerogels were used for hormone detection. Calibration for insulin and C-peptide in standard solutions was obtained in the nM range. In addition, NASA-Ames is also interested in developing a reagentless biosensor using bacterial periplasmic binding proteins (bPBPs) to detect specific biomarkers, such as amino acids and phosphate. These bPBPs were doubly labeled with two different fluorophores and encapsulated in silica xerogels. Ligand-binding experiments were performed on the bPBPs in solution and in sol-gel. Ligand-binding was monitored by fluorescence resonance energy transfer (FRET) between the two fluorophores on the bPBP. Titration data show that one bPBP has retained its ligand-binding properties in sol-gel.

Accelerated in-vitro release testing methods for extended-release parenteral dosage forms.

Science.gov (United States)

Shen, Jie; Burgess, Diane J

2012-07-01

This review highlights current methods and strategies for accelerated in-vitro drug release testing of extended-release parenteral dosage forms such as polymeric microparticulate systems, lipid microparticulate systems, in-situ depot-forming systems and implants. Extended-release parenteral dosage forms are typically designed to maintain the effective drug concentration over periods of weeks, months or even years. Consequently, 'real-time' in-vitro release tests for these dosage forms are often run over a long time period. Accelerated in-vitro release methods can provide rapid evaluation and therefore are desirable for quality control purposes. To this end, different accelerated in-vitro release methods using United States Pharmacopeia (USP) apparatus have been developed. Different mechanisms of accelerating drug release from extended-release parenteral dosage forms, along with the accelerated in-vitro release testing methods currently employed are discussed. Accelerated in-vitro release testing methods with good discriminatory ability are critical for quality control of extended-release parenteral products. Methods that can be used in the development of in-vitro-in-vivo correlation (IVIVC) are desirable; however, for complex parenteral products this may not always be achievable. © 2012 The Authors. JPP © 2012 Royal Pharmaceutical Society.

Accelerated in vitro release testing methods for extended release parenteral dosage forms

Science.gov (United States)

Shen, Jie; Burgess, Diane J.

2012-01-01

Objectives This review highlights current methods and strategies for accelerated in vitro drug release testing of extended release parenteral dosage forms such as polymeric microparticulate systems, lipid microparticulate systems, in situ depot-forming systems, and implants. Key findings Extended release parenteral dosage forms are typically designed to maintain the effective drug concentration over periods of weeks, months or even years. Consequently, “real-time” in vitro release tests for these dosage forms are often run over a long time period. Accelerated in vitro release methods can provide rapid evaluation and therefore are desirable for quality control purposes. To this end, different accelerated in vitro release methods using United States Pharmacopoeia (USP) apparatus have been developed. Different mechanisms of accelerating drug release from extended release parenteral dosage forms, along with the accelerated in vitro release testing methods currently employed are discussed. Conclusions Accelerated in vitro release testing methods with good discriminatory ability are critical for quality control of extended release parenteral products. Methods that can be used in the development of in vitro-in vivo correlation (IVIVC) are desirable, however for complex parenteral products this may not always be achievable. PMID:22686344

National Atmospheric Release Advisory Center (NARAC) Capabilities for Homeland Security

Energy Technology Data Exchange (ETDEWEB)

Sugiyama, G; Nasstrom, J; Baskett, R; Simpson, M

2010-03-08

The Department of Energy's National Atmospheric Release Advisory Center (NARAC) provides critical information during hazardous airborne releases as part of an integrated national preparedness and response strategy. Located at Lawrence Livermore National Laboratory, NARAC provides 24/7 tools and expert services to map the spread of hazardous material accidentally or intentionally released into the atmosphere. NARAC graphical products show affected areas and populations, potential casualties, and health effect or protective action guideline levels. LLNL experts produce quality-assured analyses based on field data to assist decision makers and responders. NARAC staff and collaborators conduct research and development into new science, tools, capabilities, and technologies in strategically important areas related to airborne transport and fate modeling and emergency response. This paper provides a brief overview of some of NARAC's activities, capabilities, and research and development.

News/Press Releases

Data.gov (United States)

Office of Personnel Management — A press release, news release, media release, press statement is written communication directed at members of the news media for the purpose of announcing programs...

Investigation of tritium release and retention in lithium aluminate

International Nuclear Information System (INIS)

Kopasz, J.P.; Tistchenko, S.; Botter, F.

1991-01-01

Tritium release from lithium aluminate, although previously investigated by both in-reactor and ex-reactor experiments, remains poorly understood. Agreement between experiments is lacking, and the mechanisms responsible for tritium release from lithium aluminate are under debate. In an effort to improve our understanding of the mechanisms of tritium release from lithium ceramics, we have investigated tritium release from pure lithium aluminate and lithium aluminate doped with impurities. The results of these experiments on large grain size material indicate that after anneals at low temperature, a large fraction of the tritium present before the anneal remains in the sample. We have modeled this behavior based on first-order release from three types of sites. At the lowest temperature, the release is dominated by one site, while the tritium in the other sites is retained in the solid. Adding magnesium dopant to the ceramic appears to alter the distribution of tritium between the sites. This addition decreases the fraction of tritium released at 777 degree C, while increasing the fractions released at 538 and 950 degree C. 11 refs., 8 figs., 1 tab

Health and environmental impacts of a fertilizer plant - Part I: Assessment of radioactive pollution

Energy Technology Data Exchange (ETDEWEB)

Righi, Serena [Interdepartment Centre for Research in Environmental Science, University of Bologna, via dell' Agricoltura 5, 48100 Ravenna (Italy)]. E-mail: serena.righi2@unibo.it; Lucialli, Patrizia [ARPA, Emilia-Romagna Regional Agency for Prevention and Environment, Department of Ravenna, via Alberoni 17/19, 48100 Ravenna (Italy); Bruzzi, Luigi [Interdepartment Centre for Research in Environmental Science, University of Bologna, via dell' Agricoltura 5, 48100 Ravenna (Italy)

2005-07-01

The aim of the first part of this investigation is to assess the radioactive pollution caused by a production plant of complex fertilizers (that is to say containing nitrogen, phosphorus and, in some cases, potassium). Firstly, the authors determine the concentrations of natural radioactivity present in raw materials, end products and wastes of the industrial plant. Then, they carry out an assessment of radioactive releases into the atmosphere, hydrosphere and lithosphere as well as of their significance from the environmental point of view. The second part of the investigation will be aimed at assessing the annual effective doses to plant workers and to members of the population surrounding the industrial site.

Health and environmental impacts of a fertilizer plant - Part I: Assessment of radioactive pollution

International Nuclear Information System (INIS)

Righi, Serena; Lucialli, Patrizia; Bruzzi, Luigi

2005-01-01

The aim of the first part of this investigation is to assess the radioactive pollution caused by a production plant of complex fertilizers (that is to say containing nitrogen, phosphorus and, in some cases, potassium). Firstly, the authors determine the concentrations of natural radioactivity present in raw materials, end products and wastes of the industrial plant. Then, they carry out an assessment of radioactive releases into the atmosphere, hydrosphere and lithosphere as well as of their significance from the environmental point of view. The second part of the investigation will be aimed at assessing the annual effective doses to plant workers and to members of the population surrounding the industrial site

Model to estimate radiation dose commitments to the world population from the atmospheric release of radionuclides (LWBR development program)

International Nuclear Information System (INIS)

Rider, J.L.; Beal, S.K.

1978-02-01

The equations developed for use in the LWBR environmental statement to estimate the dose commitment over a given time interval to a given organ of the population in the entire region affected by the atmospheric releases of a radionuclide are presented and may be used for any assessment of dose commitments in these regions. These equations define the dose commitments to the world resulting from a released radionuclide and each of its daughters and the sum of these dose commitments provides the total dose commitment accrued from the release of a given radionuclide. If more than one radionuclide is released from a facility, then the sum of the dose commitments from each released nuclide and from each daughter of each released nuclide is the total dose commitment to the world from that facility. Furthermore, if more than one facility is considered as part of an industry, then the sum of the dose commitments from the individual facilities represents the total world dose commitment associated with that industry. The actual solutions to these equations are carried out by the AIRWAY computer program. The writing of this computer program entailed defining in detail the specific representations of the various parameters such as scavenging coefficients, resuspension factors, deposition velocities, dose commitment conversion factors, and food uptake factors, in addition to providing specific numerical values for these types of parameters. The program permits the examination of more than one released nuclide at a time and performs the necessary summing to obtain the total dose commitment to the world accrued from the specified releases

Measures for Management of Land Use Master Plan Released

Institute of Scientific and Technical Information of China (English)

Qian Fang; Li Caige

2017-01-01

On May 8,2017,the Measures for Management of Land Use Master Plan was released for enforcement by the Ministry of Land and Resources.The Measures clearly points out that a land use master plan is an essential part of the national spatial planning system and an important basis for implementing land use modes control and management,

Importance of vesicle release stochasticity in neuro-spike communication.

Science.gov (United States)

Ramezani, Hamideh; Akan, Ozgur B

2017-07-01

Aim of this paper is proposing a stochastic model for vesicle release process, a part of neuro-spike communication. Hence, we study biological events occurring in this process and use microphysiological simulations to observe functionality of these events. Since the most important source of variability in vesicle release probability is opening of voltage dependent calcium channels (VDCCs) followed by influx of calcium ions through these channels, we propose a stochastic model for this event, while using a deterministic model for other variability sources. To capture the stochasticity of calcium influx to pre-synaptic neuron in our model, we study its statistics and find that it can be modeled by a distribution defined based on Normal and Logistic distributions.

Analysis of an LPG accidental release

Energy Technology Data Exchange (ETDEWEB)

Demichela, M.; Piccinini, N.; Poggio, A.

2004-03-01

An industrial LPG storage accident due to the release of propane from a tanker is described in this paper and the sequence of events that led to the collapse of a storage tank is examined using simulation software. A model taking both released flows into account as a radiant thermal contribution in the presence of flames is presented. The progression of the accident is assessed through digitalization and processing of the film of the fireball produced by about 500 L of LPG, whose diameter was calculated as approximately 50 m. (author)

Free release measurement of radioactive waste on the basis of the Bayes theory

International Nuclear Information System (INIS)

Sokcic-Kostic, M.; Langer, F.; Schultheis, R.

2013-01-01

The application of Bayesian theory in the evaluation of the free release measurements requires complex co-ordination between experiment and analysis. The algorithms are more complex compared to those used in the frequentist data analysis and partly to those of the Monte Carlo methods. The user can get an objective treatment of parameters of the measurement error and - as a result - a reliable indication of confidence intervals. For release measurement, the upper limit of the confidence interval must be compared with the limit given by the Radiation Protection Regulations (StrlSchV) to decide on a possible release of the material under test. (orig.)

Ultraviolet radiation stimulates the release of arachidonic acid from mammalian cells in culture

International Nuclear Information System (INIS)

De Leo, V.A.; Hanson, D.; Weinstein, I.B.; Harber, L.C.

1985-01-01

C3H 10T1/2 cells in culture were prelabelled with [ 3 H]arachidonic acid and exposed to UVB radiation. Almost immediately after irradiation cells released labelled arachidonate metabolites into media in a dose dependent manner. This release was inhibited by removing calcium ions from the system and by the addition of dexamethasone and parabromophenacyl bromide to the system. This suggests that the UVB stimulated release of arachidonic acid from membrane phospholipids is, in part, mediated by a phospholipase A 2 enzyme system. Thin layer chromatographic examination of media extracts revealed a dose dependent UVB stimulation of prostaglandin production by cultured cells. (author)

Release rates from waste packages in a salt repository

International Nuclear Information System (INIS)

Chambre, P.L.; Hwang, Y.; Lee, W.W.L.; Pigford, T.H.

1987-06-01

In this report we present estimates of radionuclide release rates from waste packages into salt. This conservative and bounding analysis shows that release rates from waste packages in salt are well below the US Nuclear Regulatory Commission's performance objectives for the engineered barrier system. 2 refs., 2 figs

A history of effluent releases from the Texas A and M University reactor

Energy Technology Data Exchange (ETDEWEB)

Bates, E F; Neff, R D; Sandel, P S; Schoenbucher, B [Texas A and M University (United States)

1974-07-01

Since 1966 records of radioactive effluents releases from the Texas A and M University Research Reactor have been compiled. These data include particulate activity, noble gases, and liquid effluent releases. Particulate activity releases with half-lives greater than eight days were negligible and are not included in this presentation. Conversion from an MTR plate reactor to a TRIGA fueled reactor was completed in August 1968. Records of effluent releases of Argon-4l and liquids for the past, five years are summarized, in this presentation. These release data are compared to the current limits specified: in 10 CPR 20 and the limits appearing in proposed Appendix.

Nitric Oxide-Releasing Silica Nanoparticle-Doped Polyurethane Electrospun Fibers

Science.gov (United States)

Koh, Ahyeon; Carpenter, Alexis W.; Slomberg, Danielle L.; Schoenfisch, Mark H.

2013-01-01

Electrospun polyurethane fibers doped with nitric oxide (NO)-releasing silica particles are presented as novel macromolecular scaffolds with prolonged NO-release and high porosity. Fiber diameter (119–614 nm) and mechanical strength (1.7–34.5 MPa of modulus) were varied by altering polyurethane type and concentration, as well as the NO-releasing particle composition, size, and concentration. The resulting NO-releasing electrospun nanofibers exhibited ~83% porosity with flexible plastic or elastomeric behavior. The use of N-diazeniumdiolate- or S-nitrosothiol-modified particles yielded scaffolds exhibiting a wide range of NO release totals and durations (7.5 nmol mg−1–0.12 μmol mg−1 and 7 h to 2 weeks, respectively). The application of NO-releasing porous materials as coating for subcutaneous implants may improve tissue biocompatibility by mitigating the foreign body response and promoting cell integration. PMID:23915047

ELSA: A simplified code for fission product release calculations

International Nuclear Information System (INIS)

Manenc, H.; Notley, M.J.

1996-01-01

During a light water reactor severe accident, fission products are released from the overheated core as it progressively degrades. A new computer module named ELSA is being developed to calculate fission product release. The authors approach is to model the key phenomena, as opposed to more complete mechanistic approaches. Here they present the main features of the module. Different release mechanisms have been identified and are modeled in ELSA, depending on fission product volatility: diffusion seems to govern the release of the highly volatile species if fuel oxidation is properly accounted for, whereas mass transport governs that of lower volatility fission products and fuel volatilization that of the practically involatile species

Selected Papers and Presentations Presented at MODSIM World 2010 Conference Expo. Part 2

Science.gov (United States)

Pinelli, Thomas E. (Editor)

2011-01-01

MODSIM World 2010 was held in Hampton, Virginia, October 13-15, 2010. The theme of the 2010 conference & expo was "21st Century Decision-Making: The Art of Modeling& Simulation". The conference program consisted of seven technical tracks - Defense, Engineering and Science, Health & Medicine, Homeland Security & First Responders, The Human Dimension, K-20 STEM Education, and Serious Games & Virtual Worlds. Selected papers and presentations from MODSIM World 2010 Conference & Expo are contained in this NASA Conference Publication (CP). Section 8.0 of this CP contains papers from MODSIM World 2009 Conference & Expo that were unavailable at the time of publication of NASA/CP-2010-216205 Selected Papers Presented at MODSIM World 2009 Conference and Expo, March 2010.

Renal epithelial cells can release ATP by vesicular fusion

Directory of Open Access Journals (Sweden)

Randi G Bjaelde

2013-09-01

Full Text Available Renal epithelial cells have the ability to release nucleotides as paracrine factors. In the intercalated cells of the collecting duct, ATP is released by connexin30 (cx30, which is selectively expressed in this cell type. However, ATP is released by virtually all renal epithelia and the aim of the present study was to identify possible alternative nucleotide release pathways in a renal epithelial cell model. We used MDCK (type1 cells to screen for various potential ATP release pathways. In these cells, inhibition of the vesicular H+-ATPases (bafilomycin reduced both the spontaneous and hypotonically (80%-induced nucleotide release. Interference with vesicular fusion using N-ethylamide markedly reduced the spontaneous nucleotide release, as did interference with trafficking from the endoplasmic reticulum to the Golgi apparatus (brefeldin A1 and vesicular transport (nocodazole. These findings were substantiated using a siRNA directed against SNAP-23, which significantly reduced spontaneous ATP release. Inhibition of pannexin and connexins did not affect the spontaneous ATP release in this cell type, which consists of ∼90% principal cells. TIRF-microscopy of either fluorescently-labeled ATP (MANT-ATP or quinacrine-loaded vesicles, revealed that spontaneous release of single vesicles could be promoted by either hypoosmolality (50% or ionomycin. This vesicular release decreased the overall cellular fluorescence by 5.8% and 7.6% respectively. In summary, this study supports the notion that spontaneous and induced ATP release can occur via exocytosis in renal epithelial cells.

Application for approval of derived authorized limits for the release of the 190-C trenches and 105-C process water tunnels at the Hanford Site: Volume 2 - source term development

International Nuclear Information System (INIS)

Denham, D.H.; Winslow, S.L.; Moeller, M.P.; Kennedy, W.E. Jr.

1997-03-01

As part of environmental restoration activities at the Hanford Site, Bechtel Hanford, Inc. is conducting a series of evaluations to determine appropriate release conditions for specific facilities following the completion of decontamination and decommissioning projects. The release conditions, with respect to the residual volumetric radioactive contamination, are termed authorized limits. This report presents the summary of the supporting information and the final application for approval of derived authorized limits for the release of the 190-C trenches and the 105-C process water tunnels. This document contains two volumes; this volume (Vol. 2) contains the radiological characterization data, spreadsheet analyses, and radiological source terms

Intestinal and peritoneal mast cells differ in kinetics of quantal release

Energy Technology Data Exchange (ETDEWEB)

Balseiro-Gomez, Santiago, E-mail: sanbalgom@alum.us.es; Ramirez-Ponce, M. Pilar, E-mail: pponce@us.es; Acosta, Jorge, E-mail: jorgealo@us.es; Ales, Eva, E-mail: eales@us.es; Flores, Juan A., E-mail: jaflores@us.es

2016-01-15

5-hydroxytriptamine (5-HT, serotonin) storage and release in mast cell (MC) secretory granules (SG) are dependent on serglycin proteoglycans (PG). This notion is based on the studies of MC of the connective tissue subtype that predominantly contain PG of the heparin type, whereas intestinal mucosal MC, which contain predominantly chondroitin sulfate, have been poorly explored. In the present study, we addressed the possibility that PG contents may differently affect the storage and release of preformed mediators in these two MC subclasses and explain in part their different functional properties. Rat peritoneal (PMC) and intestinal mast cells (IMC) were isolated and purified using a percoll gradient, and the efflux of 5-HT from each SG was measured by amperometric detection. IMC exhibited a ∼34% reduction in the release of 5-HT compared with PMC because of a lower number of exocytotic events, rather than a lower secretion per single exocytotic event. Amperometric spikes from IMC exhibited a slower decay phase and increased half-width but a similar ascending phase and foot parameters, indicating that the fusion pore kinetics are comparable in both MC subclasses. We conclude that both PG subtypes are equally efficient systems, directly involved in serotonin accumulation, and play a crucial role in regulating the kinetics of exocytosis from SG, providing specific secretory properties for the two cellular subtypes. - Highlights: • We improved a method for isolating and purifying IMC. • There was a reduction in total serotonin release in IMC with respect to PMC. • This decrease was not due to less secretion per quantum but a lower number of exocytotic events. • There was also a deceleration of exocytosis in IMC with respect to PMC.

Source Release Modeling for the Idaho National Engineering and Environmental Laboratory's Subsurface Disposal Area

International Nuclear Information System (INIS)

Becker, B.H.

2002-01-01

A source release model was developed to determine the release of contaminants into the shallow subsurface, as part of the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) evaluation at the Idaho National Engineering and Environmental Laboratory's (INEEL) Subsurface Disposal Area (SDA). The output of the source release model is used as input to the subsurface transport and biotic uptake models. The model allowed separating the waste into areas that match the actual disposal units. This allows quantitative evaluation of the relative contribution to the total risk and allows evaluation of selective remediation of the disposal units within the SDA

Hindered disulfide bonds to regulate release rate of model drug from mesoporous silica.

Science.gov (United States)

Nadrah, Peter; Maver, Uroš; Jemec, Anita; Tišler, Tatjana; Bele, Marjan; Dražić, Goran; Benčina, Mojca; Pintar, Albin; Planinšek, Odon; Gaberšček, Miran

2013-05-01

With the advancement of drug delivery systems based on mesoporous silica nanoparticles (MSNs), a simple and efficient method regulating the drug release kinetics is needed. We developed redox-responsive release systems with three levels of hindrance around the disulfide bond. A model drug (rhodamine B dye) was loaded into MSNs' mesoporous voids. The pore opening was capped with β-cyclodextrin in order to prevent leakage of drug. Indeed, in absence of a reducing agent the systems exhibited little leakage, while the addition of dithiothreitol cleaved the disulfide bonds and enabled the release of cargo. The release rate and the amount of released dye were tuned by the level of hindrance around disulfide bonds, with the increased hindrance causing a decrease in the release rate as well as in the amount of released drug. Thus, we demonstrated the ability of the present mesoporous systems to intrinsically control the release rate and the amount of the released cargo by only minor structural variations. Furthermore, an in vivo experiment on zebrafish confirmed that the present model delivery system is nonteratogenic.

Orientation of pigeons exposed to constant light and released from familiar sites.

Science.gov (United States)

Dall'Antonia, P; Luschi, P

1993-12-01

It has been proposed that homing pigeons may use pilotage to orient home when released from familiar sites. To test this possibility, a group of pigeons was released from familiar locations after being exposed to a constant bright light. This treatment produced the loss of the circadian rhythmicity of general activity of the birds and thus presumably impaired their time-compensating sun compass mechanism. Experimental birds, both anosmic and olfactorily unimpaired, did not show any tendency to orient home, their bearing distributions being generally not different from random. Their homing performances were also affected. These results show that initial orientation of pigeons released from familiar sites entails the use of the sun compass even when the birds are released after a treatment that makes them arrhythmic in their activity. The possibility that pilotage may play a role in the first part of the homing flight of pigeons remains to be demonstrated.

Role of various natural, synthetic and semi-synthetic polymers on drug release kinetics of losartan potassium oral controlled release tablets.

Science.gov (United States)

Jayasree, J; Sivaneswari, S; Hemalatha, G; Preethi, N; Mounika, B; Murthy, S Vasudeva

2014-10-01

The objective of the present work was to formulate and to characterize controlled release matrix tablets of losartan potassium in order to improve bioavailability and to minimize the frequency of administration and increase the patient compliance. Losartan potassium controlled release matrix tablets were prepared by direct compression technique by the use of different natural, synthetic and semisynthetic polymers such as gum copal, gum acacia, hydroxypropyl methyl cellulose K100 (HPMC K100), eudragit RL 100 and carboxy methyl ethyl cellulose (CMEC) individually and also in combination. Studies were carried out to study the influence of type of polymer on drug release rate. All the formulations were subjected to physiochemical characterization such as weight variation, hardness, thickness, friability, drug content, and swelling index. In vitro dissolution studies were carried out simulated gastric fluid (pH 1.2) for first 2 h and followed by simulated intestinal fluid (pH 6.8) up to 24 h, and obtained dissolution data were fitted to in vitro release kinetic equations in order to know the order of kinetics and mechanism of drug release. Results of physiochemical characterization of losartan potassium matrix tablets were within acceptable limits. Formulation containing HPMC K100 and CMEC achieved the desired drug release profile up to 24 h followed zero order kinetics, release pattern dominated by Korsmeyer - Peppas model and mechanism of drug release by nonfickian diffusion. The good correlation obtained from Hixson-Crowell model indicates that changes in surface area of the tablet also influences the drug release. Based on the results, losartan potassium controlled release matrix tablets prepared by employing HPMC K100 and CMEC can attain the desired drug release up to 24 h, which results in maintaining steady state concentration and improving bioavailability.

Environmental releases for calendar year 1994

International Nuclear Information System (INIS)

Gleckler, B.P.

1995-07-01

This report fulfills the annual environmental release reporting requirements of US Department of Energy (DOE) Orders. This report provides supplemental information to the Hanford Site Environmental Report. The Hanford Site Environmental Report provides an update on the environmental status of the entire Hanford Site. The sitewide annual report summarizes the degree of compliance of the Hanford Site with applicable environmental regulations and informs the public about the impact of Hanford operations on the surrounding environment. Like the Hanford Site Environmental Report, this annual report presents a summary of the environmental releases from facilities managed by the Westinghouse Hanford Company (WHC) and monitored by Bechtel Hanford, Incorporated (BHI). In addition to the summary data, this report also includes detailed data on air emissions, liquid effluents, and hazardous substances released to the environment during calendar year 1994 from these facilities

Norepinephrine storage, distribution, and release in diabetic cardiomyopathy

International Nuclear Information System (INIS)

Ganguly, P.K.; Beamish, R.E.; Dhalla, K.S.; Innes, J.R.; Dhalla, N.S.

1987-01-01

The ability of hearts to store, distribute, and release norepinephrine (NE) was investigated in rats 8 wk after the induction of diabetes by an injection of streptozotocin. Chronic diabetes was associated with increased content and concentration of NE in heart and in other tissues such as kidney, brain, and spleen. Reserpine or tyramine treatment resulted in depletion of endogenous cardiac NE in control and diabetic rats. The depletion of NE stores at different times after a dose of reserpine was greater in diabetic hearts. On the other hand, NE stores in diabetic hearts were less sensitive than control hearts to low doses of tyramine but were more sensitive to high doses. The uptake of [ 3 H]NE was greater in diabetic hearts in isolated perfused preparations. In comparison with the control values, diabetic hearts showed a decrease in [ 3 H]NE in the granular fraction and an increase in the supernatant fraction. Diabetic hearts also showed an accelerated spontaneous release of [ 3 H]NE. The increased cardiac NE and the uptake and release of NE in diabetic animals were reversible upon treatment with insulin. These results are consistent with the view that sympathetic activity is increased in diabetic cardiomyopathy and indicate that cardiac NE in diabetic rats is maintained at a higher level partly due to an increased uptake of released NE by adrenergic nerve terminals

LNG containment release: Comparison of NFPA-59A and 49-CFR-193

International Nuclear Information System (INIS)

West, H.H.; Pfenning, D.B.

1994-01-01

Due to the potential wide area impact of an unplanned LNG (Liquefied Natural Gas) release, the National Fire Protection Association (NFPA) and later the US Department of Transportation issued standards and regulations which included specific methodologies for analyzing the consequence of an accidental LNG release. The concept of a ''design spill'' was defined in order to evaluate the consequences of an accidental LNG release, with particular attention to the influence of safety protective measures. In addition to specifying the magnitude of the unplanned release, the design spill also specified some of the parameters for estimation of the downwind LNG vapor dispersion and the extent of the radiant heat from an LNG pool fire. Since the NFPA-59A and 49-CFR-193 standards were the first in-depth regulation to address consequence analysis estimation for petroleum components, it is particularly important to consider their details in light of the recently proposed EPA 40-CFR-68 regulations [Risk Management for Chemical Accidental Release Prevention] which specifically address consequence analysis as a part of process safety management

The mechanism of nuclear energy release in nucleus-nucleus collisions

International Nuclear Information System (INIS)

Strugalski, Z.; Strugalska-Gola, E.

1998-01-01

The mechanism of intranuclear energy release in reactions induced by nucleus-nucleus collisions at energies higher than ∼ 0.5 GeV/nucl. is presented - as prompted experimentally. The intranuclear energy release goes through local damages of the colliding nuclei

Toxic chemical considerations for tank farm releases. Revision 1

Energy Technology Data Exchange (ETDEWEB)

Van Keuren, J.C.

1995-11-01

This document provides a method of determining the toxicological consequences of accidental releases from Hanford Tank Farms. A determination was made of the most restrictive toxic chemicals that are expected to be present in the tanks. Concentrations were estimated based on the maximum sample data for each analyte in all the tanks in the composite. Composite evaluated were liquids and solids from single shell tanks, double shell tanks, flammable gas watch list tanks, as well as all solids, all liquids, head space gases, and 241-C-106 solids. A sum of fractions of the health effects was computed for each composite for unit releases based emergency response planning guidelines (ERPGs). Where ERPGs were not available for chemical compounds of interest, surrogate guidelines were established. The calculation method in this report can be applied to actual release scenarios by multiplying the sum of fractions by the release rate for continuous releases, or the release amount for puff releases. Risk guidelines are met if the product is less than for equal to one.

Toxic chemical considerations for tank farm releases. Revision 1

International Nuclear Information System (INIS)

Van Keuren, J.C.

1995-11-01

This document provides a method of determining the toxicological consequences of accidental releases from Hanford Tank Farms. A determination was made of the most restrictive toxic chemicals that are expected to be present in the tanks. Concentrations were estimated based on the maximum sample data for each analyte in all the tanks in the composite. Composite evaluated were liquids and solids from single shell tanks, double shell tanks, flammable gas watch list tanks, as well as all solids, all liquids, head space gases, and 241-C-106 solids. A sum of fractions of the health effects was computed for each composite for unit releases based emergency response planning guidelines (ERPGs). Where ERPGs were not available for chemical compounds of interest, surrogate guidelines were established. The calculation method in this report can be applied to actual release scenarios by multiplying the sum of fractions by the release rate for continuous releases, or the release amount for puff releases. Risk guidelines are met if the product is less than for equal to one

Containment and release management

International Nuclear Information System (INIS)

Lehner, J.R.; Pratt, W.T.

1988-01-01

Reducing the risk from potentially severe accidents by appropriate accident management strategies is receiving increased attention from the international reactor safety community. Considerable uncertainty still surrounds some of the physical phenomena likely to occur during a severe accident. The USNRC, in developing its research plan for accident management, wants to ensure that both the developers and implementers of accident management strategies are aware of the uncertainty associated with the plant operators' ability to correctly diagnose an accident, as well as the uncertainties associated with various preventive and mitigative strategies. The use of a particular accident management strategy can have both positive and negative effects on the status of a plant and these effects must be carefully weighed before a particular course of action is chosen and implemented. By using examples of severe accident scenarios, initial insights are presented here regarding the indications plant operators may have to alert them to particular accident states. Insights are also offered on the various management actions operators and plant technical staff might pursue for particular accident situations and the pros and cons associated with such actions. The examples given are taken for the most part from the containment and release phase of accident management, since this is the current focus of the effort in the accident management area at Brookhaven National Laboratory. 2 refs

Hydraulic running and release tool with mechanical emergency release

International Nuclear Information System (INIS)

Baker, S.F.

1991-01-01

This patent describes a setting tool for connection in a well string to position a tubular member in a well bore. It comprises: a mandrel adapted to be connected to the well string; an outer sleeve surrounding the mandrel and releasably secured thereto; a latch nut releasably connected to the outer sleeve; piston means sealingly engaging the mandrel; shear means releasably securing the piston to the latch nut to maintain the latch nut releasably connected to the tubular member; the mandrel having port means for conducting fluid pressure from the well string to release the piston means from and the latch nut; cooperating engageable surfaces on the piston and latch nut to reengage them together after the piston moves a predetermined longitudinal distance relative to the latch nut; and additional cooperating engageable surfaces on the latch nut and the outer sleeve which are engageable when the piston and engaged latch nut are moved a predetermined additional longitudinal distance by fluid pressure to secure the engaged piston and latch nut with the outer sleeve for retrieval along with the mandrel from the well bore

Fate of corrosion products released from stainless steel in marine sediments and seawater. Part 4: Hatteras abyssal red clay

International Nuclear Information System (INIS)

Schmidt, R.L.

1982-07-01

A study in which neutron-activated 347 stainless steel was exposed to surficial sediment from a site in the Hatteras Abyssal Plain of the Northwest Atlantic Ocean is described. This sediment consists of approx. 20% CaCO 3 , which could lead to the formation of calcareous scale on the metal surface and reduce the corrosion rate. The distribution of indigenous metals among different chemical fractions shows that extractable Cr, Mn, Fe, Co, and Zn were associated with amorphous Mn and Fe oxides. Most of the remaining extractable Cr, and about a third of the extractable Cu appear to have been weakly complexed. Major fractions (25 to 36%) of extractable Mn, Co and Ni were present as adsorbed cations. Organic complexation appears to account for a large amount of extractable Fe, Ni, Cu and Zn. Neutron-activated 347 stainless steel specimens were exposed to sediment slurry under aerobic and non-oxygenated conditions for a period of 94 days. The redox potential measurements for air-sparged and N 2 , CO 2 -sparged sediment slurries were +410 and +60 mv, respectively. The presence of 0 2 produced increased amounts of corrosion products. Chemical extraction showed that relatively labile substances constituted about 84% of the 60 Co activity released in aerated sediment. Relatively labile substances constitute about 82% of the total 60 Co activity released under non-oxygenated conditions. A large fraction of 60 Co which was in the soluble or easily dissolved forms under non-oxygenated conditions appears to have been more strongly adsorbed to the sediment under aerated conditions

Atmospheric Dispersion Modeling of the February 2014 Waste Isolation Pilot Plant Release

Energy Technology Data Exchange (ETDEWEB)

Nasstrom, John [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Piggott, Tom [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Simpson, Matthew [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Lobaugh, Megan [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Tai, Lydia [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Pobanz, Brenda [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Yu, Kristen [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

2015-07-22

This report presents the results of a simulation of the atmospheric dispersion and deposition of radioactivity released from the Waste Isolation Pilot Plant (WIPP) site in New Mexico in February 2014. These simulations were made by the National Atmospheric Release Advisory Center (NARAC) at Lawrence Livermore National Laboratory (LLNL), and supersede NARAC simulation results published in a previous WIPP report (WIPP, 2014). The results presented in this report use additional, more detailed data from WIPP on the specific radionuclides released, radioactivity release amounts and release times. Compared to the previous NARAC simulations, the new simulation results in this report are based on more detailed modeling of the winds, turbulence, and particle dry deposition. In addition, the initial plume rise from the exhaust vent was considered in the new simulations, but not in the previous NARAC simulations. The new model results show some small differences compared to previous results, but do not change the conclusions in the WIPP (2014) report. Presented are the data and assumptions used in these model simulations, as well as the model-predicted dose and deposition on and near the WIPP site. A comparison of predicted and measured radionuclide-specific air concentrations is also presented.

Proceedings of the Scientific Meeting and Presentation on Basic Research in Nuclear of the Science and Technology part I : Physics and Nuclear Reactor

International Nuclear Information System (INIS)

Kusminarto; Sri Juari Santoso; Agus Taftazani; Sudjatmoko; Darsono; Samin; Syarip; Prajitno; Muhadi Ayub Wasitho; Sukarsono; Tjipto Sujitno; Elisabeth Supriyatni

2009-07-01

The Scientific Meeting and Presentation on Basic Research in Nuclear Science and Technology is a routine activity held by Centre for Accelerator Technology and Material Process, National Nuclear Energy Agency, for monitoring the research activity which achieved in National Nuclear Energy Agency. The proceedings contains papers presented on scientific meeting about Physics and Nuclear Reactor. The proceedings is the first part of the three parts which published in series. There are 28 papers. (PPIN)

Instant release fraction and matrix release of high burn-up UO{sub 2} spent nuclear fuel: Effect of high burn-up structure and leaching solution composition

Energy Technology Data Exchange (ETDEWEB)

Serrano-Purroy, D., E-mail: Daniel.serrano-purroy@ec.europa.eu [European Commission, Joint Research Centre, Institute for Transuranium Elements, P.O. Box 2340, D-76125 Karlsruhe (Germany); Clarens, F.; Gonzalez-Robles, E. [CTM Centre Tecnologic, Avda. Bases de Manresa 1, 08240 Barcelona (Spain); Glatz, J.P.; Wegen, D.H. [European Commission, Joint Research Centre, Institute for Transuranium Elements, P.O. Box 2340, D-76125 Karlsruhe (Germany); Pablo, J. de [CTM Centre Tecnologic, Avda. Bases de Manresa 1, 08240 Barcelona (Spain); Department of Chemical Engineering, Universitat Politecnica de Catalunya, Avda. Diagonal 647, 08028 Barcelona (Spain); Casas, I.; Gimenez, J. [Department of Chemical Engineering, Universitat Politecnica de Catalunya, Avda. Diagonal 647, 08028 Barcelona (Spain); Martinez-Esparza, A. [ENRESA, C/Emilio Vargas 7, 28043 Madrid (Spain)

2012-08-15

Two weak points in Performance Assessment (PA) exercises regarding the alteration of Spent Nuclear Fuel (SNF) are the contribution of the so-called Instant Release Fraction (IRF) and the effect of High Burn-Up Structure (HBS). This manuscript focuses on the effect of HBS in matrix (long term) and instant release of a Pressurised Water Reactor (PWR) SNF irradiated in a commercial reactor with a mean Burn-Up (BU) of 60 GWd/tU. In order to study the HBS contribution, two samples from different radial positions have been prepared. One from the centre of the SNF, labelled CORE, and one from the periphery, enriched with HBS and labelled OUT. Static leaching experiments have been carried out with two synthetic leaching solutions: bicarbonate (BIC) and Bentonitic Granitic Groundwater (BGW), and in all cases under oxidising conditions. IRF values have been calculated from the determined Fraction of Inventory in Aqueous Phase (FIAP). In all studied cases, some radionuclides (RN): Rb, Sr and Cs, have shown higher release rates than uranium, especially at the beginning of the experiment, and have been considered as IRF. Redox sensitive RN like Mo and Tc have been found to dissolve slightly faster than uranium and further studies might be needed to confirm if they can also be considered part of the IRF. Most of the remaining studied RN, mainly actinides and lanthanides, have been found to dissolve congruently with the uranium matrix. Finally, Zr, Ru and Rh presented lower release rates than the matrix. Higher matrix release has been determined for CORE than for OUT samples showing that the formation of HBS might have a protective effect against the oxidative corrosion of the SNF. On the contrary, no significant differences have been observed between the two studied leaching solutions (BIC and BGW). Two different IRF contributions have been determined. One corresponding to the fraction of inventory segregated in the external open grain boundaries, directly available to water and

32 CFR Appendix C to Part 45 - DD Form 215

Science.gov (United States)

2010-07-01

... 32 National Defense 1 2010-07-01 2010-07-01 false DD Form 215 C Appendix C to Part 45 National... CERTIFICATE OF RELEASE OR DISCHARGE FROM ACTIVE DUTY (DD FORM 214/5 SERIES) Pt. 45, App. C Appendix C to Part 45—DD Form 215 EC21OC91.050 ...

Italian Present-day Stress Indicators: IPSI Database

Science.gov (United States)

Mariucci, M. T.; Montone, P.

2017-12-01

In Italy, since the 90s of the last century, researches concerning the contemporary stress field have been developing at Istituto Nazionale di Geofisica e Vulcanologia (INGV) with local and regional scale studies. Throughout the years many data have been analysed and collected: now they are organized and available for an easy end-use online. IPSI (Italian Present-day Stress Indicators) database, is the first geo-referenced repository of information on the crustal present-day stress field maintained at INGV through a web application database and website development by Gabriele Tarabusi. Data consist of horizontal stress orientations analysed and compiled in a standardized format and quality-ranked for reliability and comparability on a global scale with other database. Our first database release includes 855 data records updated to December 2015. Here we present an updated version that will be released in 2018, after new earthquake data entry up to December 2017. The IPSI web site (http://ipsi.rm.ingv.it/) allows accessing data on a standard map viewer and choose which data (category and/or quality) to plot easily. The main information of each single element (type, quality, orientation) can be viewed simply going over the related symbol, all the information appear by clicking the element. At the same time, simple basic information on the different data type, tectonic regime assignment, quality ranking method are available with pop-up windows. Data records can be downloaded in some common formats, moreover it is possible to download a file directly usable with SHINE, a web based application to interpolate stress orientations (http://shine.rm.ingv.it). IPSI is mainly conceived for those interested in studying the characters of Italian peninsula and surroundings although Italian data are part of the World Stress Map (http://www.world-stress-map.org/) as evidenced by many links that redirect to this database for more details on standard practices in this field.

The Goiania accident: release from hospital criterion

International Nuclear Information System (INIS)

Falcao, R.C.; Hunt, J.

1990-01-01

On the thirteenth of September 1987, a 1357 Ci Cesium source was removed from the 'Instituto de Radiologia de Goiania' - probably two or three days later the source was opened, causing the internal and external contamination of 247 people, and part of the city of Goiania. This paper describes the release from hospital criterion of the contaminated patients, based on radiation protection principles which were developed for this case. The estimate of the biological half-life for cesium is also described. (author) [pt

Release properties of UC sub x and molten U targets

CERN Document Server

Roussière, B; Sauvage, J; Bajeat, O; Barre, N; Clapier, F; Cottereau, E; Donzaud, C; Ducourtieux, M; Essabaa, S; Guillemaud-Müller, D; Lau, C; Lefort, H; Liang, C F; Le Blanc, F; Müller, A C; Obert, J; Pauwels, N; Potier, J C; Pougheon, F; Proust, J; Sorlin, O; Verney, D; Wojtasiewicz, A

2002-01-01

The release properties of UC sub x and molten U thick targets associated with a Nier-Bernas ion source have been studied. Two experimental methods are used to extract the release time. Results are presented and discussed for Kr, Cd, I and Xe.

Applicability of near-infrared spectroscopy in the monitoring of film coating and curing process of the prolonged release coated pellets.

Science.gov (United States)

Korasa, Klemen; Hudovornik, Grega; Vrečer, Franc

2016-10-10

Although process analytical technology (PAT) guidance has been introduced to the pharmaceutical industry just a decade ago, this innovative approach has already become an important part of efficient pharmaceutical development, manufacturing, and quality assurance. PAT tools are especially important in technologically complex operations which require strict control of critical process parameters and have significant effect on final product quality. Manufacturing of prolonged release film coated pellets is definitely one of such processes. The aim of the present work was to study the applicability of the at-line near-infrared spectroscopy (NIR) approach in the monitoring of pellet film coating and curing steps. Film coated pellets were manufactured by coating the active ingredient containing pellets with film coating based on polymethacrylate polymers (Eudragit® RS/RL). The NIR proved as a useful tool for the monitoring of the curing process since it was able to determine the extent of the curing and hence predict drug release rate by using partial least square (PLS) model. However, such approach also showed a number of limitations, such as low reliability and high susceptibility to pellet moisture content, and was thus not able to predict drug release from pellets with high moisture content. On the other hand, the at-line NIR was capable to predict the thickness of Eudragit® RS/RL film coating in a wide range (up to 40μm) with good accuracy even in the pellets with high moisture content. To sum up, high applicability of the at-line NIR in the monitoring of the prolonged release pellets production was demonstrated in the present study. The present findings may contribute to more efficient and reliable PAT solutions in the manufacturing of prolonged release dosage forms. Copyright © 2016 Elsevier B.V. All rights reserved.

Growth hormone-releasing peptides.

Science.gov (United States)

Ghigo, E; Arvat, E; Muccioli, G; Camanni, F

1997-05-01

Growth hormone-releasing peptides (GHRPs) are synthetic, non-natural peptides endowed with potent stimulatory effects on somatotrope secretion in animals and humans. They have no structural homology with GHRH and act via specific receptors present either at the pituitary or the hypothalamic level both in animals and in humans. The GHRP receptor has recently been cloned and, interestingly, it does not show sequence homology with other G-protein-coupled receptors known so far. This evidence strongly suggests the existence of a natural GHRP-like ligand which, however, has not yet been found. The mechanisms underlying the GHRP effect are still unclear. At present, several data favor the hypothesis that GHRPs could act by counteracting somatostatinergic activity both at the pituitary and the hypothalamic level and/or, at least partially, via a GHRH-mediated mechanism. However, the possibility that GHRPs act via an unknown hypothalamic factor (U factor) is still open. GHRP-6 was the first hexapeptide to be extensively studied in humans. More recently, a heptapeptide, GHRP-1, and two other hexapeptides, GHRP-2 and Hexarelin, have been synthesized and are now available for human studies. Moreover, non-peptidyl GHRP mimetics have been developed which act via GHRP receptors and their effects have been clearly demonstrated in animals and in humans in vivo. Among non-peptidyl GHRPs, MK-0677 seems the most interesting molecule. The GH-releasing activity of GHRPs is marked and dose-related after intravenous, subcutaneous, intranasal and even oral administration. The effect of GHRPs is reproducible and undergoes partial desensitization, more during continuous infusion, less during intermittent administration: in fact, prolonged administration of GHRPs increases IGF-1 levels both in animals and in humans. The GH-releasing effect of GHRPs does not depend on sex but undergoes age-related variations. It increases from birth to puberty, persists at a similar level in adulthood and

Blood banking-induced alteration of red blood cell oxygen release ability.

Science.gov (United States)

Li, Yaojin; Xiong, Yanlian; Wang, Ruofeng; Tang, Fuzhou; Wang, Xiang

2016-05-01

Current blood banking procedures may not fully preserve red blood cell (RBC) function during storage, contributing to the decrease of RBC oxygen release ability. This study was undertaken to evaluate the impact of routine cold storage on RBC oxygen release ability. RBC units were collected from healthy donors and each unit was split into two parts (whole blood and suspended RBC) to exclude possible donor variability. Oxygen dissociation measurements were performed on blood units stored at 4 °C during a 5-week period. 2,3-diphosphoglycerate levels and fluorescent micrographs of erythrocyte band 3 were also analysed. P50 and oxygen release capacity decreased rapidly during the first 3 weeks, and then did not change significantly. In contrast, the kinetic properties (PO2-t curve and T*50) of oxygen release changed slowly during the first 3 weeks of storage, but then decreased significantly in the last 2 weeks. 2,3-diphosphoglycerate decreased quickly during the first 3 weeks of storage to almost undetectable levels. Band 3 aggregated significantly during the last 2 weeks of storage. RBC oxygen release ability appears to be sensitive to routine cold storage. The thermodynamic characteristics of RBC oxygen release ability changed mainly in the first 3 weeks of storage, due to the decrease of 2,3-diphosphoglycerate, whereas the kinetic characteristics of RBC oxygen release ability decreased significantly at the end of storage, probably affected by alterations of band 3.

Gas Release as a Deformation Signal

Energy Technology Data Exchange (ETDEWEB)

Bauer, Stephen J. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2017-09-01

Radiogenic noble gases are contained in crustal rock at inter and intra granular sites. The gas composition depends on lithology, geologic history, fluid phases, and the aging effect by decay of U, Th, and K. The isotopic signature of noble gases found in rocks is vastly different than that of the atmosphere which is contributed by a variety of sources. When rock is subjected to stress conditions exceeding about half its yield strength, micro-cracks begin to form. As rock deformation progresses a fracture network evolves, releasing trapped noble gases and changing the transport properties to gas migration. Thus, changes in gas emanation and noble gas composition from rocks could be used to infer changes in stress-state and deformation. The purpose of this study has been to evaluate the effect of deformation/strain rate upon noble gas release. Four triaxial experiments were attempted for a strain rate range of %7E10-8 /s (180,000s) to %7E 10-4/s (500s); the three fully successful experiments (at the faster strain rates) imply the following: (1) helium is measurably released for all strain rates during deformation, this release is in amounts 1-2 orders of magnitude greater than that present in the air, and (2) helium gas release increases with decreasing strain rate.

Measurement of very low release rates of corrosion products in high temperature water

International Nuclear Information System (INIS)

Hermansson, H.-P.; Falk, I.

1984-01-01

A radiotracer technique has been developed for the measurement of release rates from nuclear reactor materials and it has been tested in a number of experiments. THis article, which forms the first part in a series, describes the experimental loop, the experimental technique and the preliminary results. Experiments were carried out on 18Cr8Ni stainless steel and on Inconel X750 in BWR primary system and feed water environments. The result show that a steady state in the release rate is achieved after operation for approximately 600 h. The release rate depends on the elemental concentration in the material and on the chemical and physical environments. Typical release rates for an 18Cr8Ni stainless steel and Inconel X750 in a BWR primary system environment were found to be 5 mdm and 8 mdm respectively. (Authors)

Mechanistic model for Sr and Ba release from severely damaged fuel

International Nuclear Information System (INIS)

Rest, J.; Cronenberg, A.W.

1985-11-01

Among radionuclides associated with fission product release during severe accidents, the primary ones with health consequences are the volatile species of I, Te, and Cs, and the next most important are Sr, Ba, and Ru. Considerable progress has been made in the mechanistic understanding of I, Cs, Te, and noble gas release; however, no capability presently exists for estimating the release of Sr, Ba, and Ru. This paper presents a description of the primary physical/chemical models recently incorporated into the FASTGRASS-VFP (volatile fission product) code for the estimation of Sr and Ba release. FASTGRASS-VFP release predictions are compared with two data sets: (1) data from out-of-reactor induction-heating experiments on declad low-burnup (1000 and 4000 MWd/t) pellets, and (2) data from the more recent in-reactor PBF Severe Fuel Damage Tests, in which one-meter-long, trace-irradiated (89 MWd/t) and normally irradiated (approx.35,000 MWd/t) fuel rods were tested under accident conditions. 10 refs

Agricultural production - Phase 2. Indonesia. Controlled release pesticide formulations

International Nuclear Information System (INIS)

Vollner, L.

1992-01-01

At the request of the Government of Indonesia, an IAEA expert undertook a two weeks mission from 2 to 15 April 1991, and continued it from the 9 to 22 November 1991 at the Center for Application of Isotopes and Radiation (CAIR) of the National Atomic Energy Agency, BATAN in Jakarta. Expert discussed the project and carried out experiments together with the staff of the center, introducing shellac (description in part II) as a candidate for controlled release formulations. Formulations of carbofuran, butachlor, 2,4-D and diazinon were carried out, using sand and cocconut shells as carriers. Release rates of a.i. into water have been checked and further work has been discussed. Expert assessed further needs for supply of instruments, accessories and chemicals. (author)

Development and Characterization of Chitosan Cross-Linked With Tripolyphosphate as a Sustained Release Agent in Tablets, Part I: Design of Experiments and Optimization.

Science.gov (United States)

Pinto, Colin A; Saripella, Kalyan K; Loka, Nikhil C; Neau, Steven H

2018-04-01

Certain issues with the use of particles of chitosan (Ch) cross-linked with tripolyphosphate (TPP) in sustained release formulations include inefficient drug loading, burst drug release, and incomplete drug release. Acetaminophen was added to Ch:TPP particles to test for advantages of drug addition extragranularly over drug addition made during cross-linking. The influences of Ch concentration, Ch:TPP ratio, temperature, ionic strength, and pH were assessed. Design of experiments allowed identification of factors and 2-factor interactions that have significant effects on average particle size and size distribution, yield, zeta potential, and true density of the particles, as well as drug release from the directly compressed tablets. Statistical model equations directed production of a control batch that minimized span, maximized yield, and targeted a t 50 of 90 min (sample A); sample B that differed by targeting a t 50 of 240-300 min to provide sustained release; and sample C that differed from sample B by maximizing span. Sample B maximized yield and provided its targeted t 50 and the smallest average particle size, with the higher zeta potential and the lower span of samples B and C. Extragranular addition of a drug to Ch:TPP particles achieved 100% drug loading, eliminated a burst drug release, and can accomplish complete drug release. Copyright © 2018 American Pharmacists Association®. Published by Elsevier Inc. All rights reserved.

Large scientific releases

International Nuclear Information System (INIS)

Pongratz, M.B.

1981-01-01

The motivation for active experiments in space is considered, taking into account the use of active techniques to obtain a better understanding of the natural space environment, the utilization of the advantages of space as a laboratory to study fundamental plasma physics, and the employment of active techniques to determine the magnitude, degree, and consequences of artificial modification of the space environment. It is pointed out that mass-injection experiments in space plasmas began about twenty years ago with the Project Firefly releases. Attention is given to mass-release techniques and diagnostics, operational aspects of mass release active experiments, the active observation of mass release experiments, active perturbation mass release experiments, simulating an artificial modification of the space environment, and active experiments to study fundamental plasma physics

Stimulatory effects of neuronally released norepinephrine on renin release in vitro

Energy Technology Data Exchange (ETDEWEB)

Matsumura, Yasuo; Kawazoe, Shinka; Ichihara, Toshio; Shinyama, Hiroshi; Kageyama, Masaaki; Morimoto, Shiro (Osaka Univ. of Pharmaceutical Sciences (Japan))

1988-10-01

Extracellular high potassium inhibits renin release in vitro by increasing calcium concentrations in the juxtaglomerular cells. The authors found that the decreased response of renin release from rat kidney cortical slices in high potassium solution changed to a strikingly increased one in the presence of nifedipine at doses over 10{sup {minus}6} M. They then examined the stimulatory effect of extracellular high potassium in the presence of nifedipine on renin release. The enhancement of release was significantly suppressed either by propranolol or by metoprolol but not by prazosin. High potassium plus nifedipine-induced increase in renin release was markedly attenuated by renal denervation. The enhancing effect was not observed when the slices were incubated in calcium-free medium. Divalent cations such as Cd{sup 2+}, Co{sup 2+}, and Mn{sup 2+} blocked this enhancement in a concentration-dependent manner. High potassium elicited an increase in {sup 3}H efflux from the slices preloaded with ({sup 3}H)-norepinephrine. The increasing effect was not influenced by nifedipine but was abolished by the removal of extracellular calcium or by the addition of divalent cations. These observations suggest to us that the high potassium plus nifedipine-induced increase in renin release from the slices is mediated by norepinephrine derived from renal sympathetic nerves and that this neuronally released norepinephrine stimulates renin release via activation of {beta}-adrenoceptors.

Simulation and parametric study of a film-coated controlled-release pharmaceutical.

Science.gov (United States)

Borgquist, Per; Zackrisson, Gunnar; Nilsson, Bernt; Axelsson, Anders

2002-04-23

Pharmaceutical formulations can be designed as Multiple Unit Systems, such as Roxiam CR, studied in this work. The dose is administrated as a capsule, which contains about 100 individual pellets, which in turn contain the active drug remoxipride. Experimental data for a large number of single pellets can be obtained by studying the release using microtitre plates. This makes it possible to study the release of the individual subunits making up the total dose. A mathematical model for simulating the release of remoxipride from single film-coated pellets is presented including internal and external mass transfer hindrance apart from the most important film resistance. The model can successfully simulate the release of remoxipride from single film-coated pellets if the lag phase of the experimental data is ignored. This was shown to have a minor influence on the release rate. The use of the present model is demonstrated by a parametric study showing that the release process is film-controlled, i.e. is limited by the mass transport through the polymer coating. The model was used to fit the film thickness and the drug loading to the experimental release data. The variation in the fitted values was similar to that obtained in the experiments.

Direct releases to the surface and associated complementary cumulative distribution functions in the 1996 performance assessment for the Waste Isolation Pilot Plant: direct brine release

International Nuclear Information System (INIS)

Stoelzel, D.M.; O'Brien, D.G.; Garner, J.W.; Helton, J.C.; Johnson, J.D.; Smith, L.N.

2000-01-01

The following topics related to the treatment of direct brine releases to the surface environment in the 1996 performance assessment for the Waste Isolation Pilot Plant (WIPP) are presented: (i) mathematical description of models; (ii) uncertainty and sensitivity analysis results arising from subjective (i.e. epistemic) uncertainty for individual releases; (iii) construction of complementary cumulative distribution functions (CCDFs) arising from stochastic (i.e. aleatory) uncertainty; and (iv) uncertainty and sensitivity analysis results for CCDFs. The presented analyses indicate that direct brine releases do not constitute a serious threat to the effectiveness of the WIPP as a disposal facility for transuranic waste. Even when the effects of uncertain analysis inputs are taken into account, the CCDFs for direct brine releases fall substantially to the left of the boundary line specified in the US Environmental Protection Agency's standard for the geologic disposal of radioactive waste (40 CFR 191, 40 CFR 194)

Correlation of recent fission product release data

International Nuclear Information System (INIS)

Kress, T.S.; Lorenz, R.A.; Nakamura, T.; Osborne, M.F.

1989-01-01

For the calculation of source terms associated with severe accidents, it is necessary to model the release of fission products from fuel as it heats and melts. Perhaps the most definitive model for fission product release is that of the FASTGRASS computer code developed at Argonne National Laboratory. There is persuasive evidence that these processes, as well as additional chemical and gas phase mass transport processes, are important in the release of fission products from fuel. Nevertheless, it has been found convenient to have simplified fission product release correlations that may not be as definitive as models like FASTGRASS but which attempt in some simple way to capture the essence of the mechanisms. One of the most widely used such correlation is called CORSOR-M which is the present fission product/aerosol release model used in the NRC Source Term Code Package. CORSOR has been criticized as having too much uncertainty in the calculated releases and as not accurately reproducing some experimental data. It is currently believed that these discrepancies between CORSOR and the more recent data have resulted because of the better time resolution of the more recent data compared to the data base that went into the CORSOR correlation. This document discusses a simple correlational model for use in connection with NUREG risk uncertainty exercises. 8 refs., 4 figs., 1 tab

Formulation And Evaluation Of Bilayer Tablet for Bimodal Release of Venlafaxine Hydrochloride

Directory of Open Access Journals (Sweden)

Munira eMomin

2015-07-01

Full Text Available The aim of the present research was to develop a bilayer tablet of venlafexine hydrochloride for bimodal drug release. In the present investigation authors have tried to explore Fenugreek Mucilage (FNM for bioadhesive sustained release layer. The attempt has been made to combine FNM with well studied bioahesive polymers like Hydroxy Propyl Methyl Cellulose, Carbopol and Xanthan Gum. The formulations were evaluated for swelling Index, ex-vivo bioadhesion, water uptake studies, in-vitro drug release and dissolution kinetics was studied. Substantial bioadhesion force (2.4±0.023 gms and tablet adhesion retention time (24±2 hrs was observed with FNM and HPMC combination at 80:20 ratio. The dissolution kinetics followed the Higuchi model (R2 =0.9913 via a non-Fickian diffusion controlled release mechanism after the initial burst. The 32 full factorial design was employed in the present study. The type of polymers used in combination with FNM (X1 and percent polymer replaced with FNM (X2 were taken as independent formulations variables. The selected responses, bioadhesion force (0.11-0.25±0.023gm, amount of drug released in 10 h, Y10 (78.20–95.78±1.24 % and bioadhesive strength, (19-24±2hrs presented good correlation with the selected independent variables. Statistical analysis (ANOVA of the optimized bilayer formulations showed no significant difference in the cumulative amount of drug release after 15 min, but significant difference (p < 0.05 in the amount of drug released after 1 hr till 12 h from optimized formulations was observed. The natural mucilage like FNM could be successfully incorporated into tablet with only 20% replacement with HPMC and it showed good bioadhesiveness and sustained drug release.

Iodine release from sodium pool combustion

International Nuclear Information System (INIS)

Sagawa, N.; Fukushima, Y.; Yokota, N.; Akagane, K.; Mochizuki, K.

1979-01-01

Iodine release associated with sodium pool combustion was determined by heating 20 gr sodium containing sodium iodide, which was labelled with 131 I and dissolved in the sodium in concentration of 1∼1,000 ppm, to burn on a nickel crucible in conditioned atmosphere in a closed vessel of 0.4 m 3 . Oxygen concentration was changed in 5∼21% and humidity in 0∼89% by mixing nitrogen gas and air. Combustion products were trapped by a Maypack filter composed of particle filters, copper screens and activated charcoal beds and by a glass beads pack cooled by liquid argon. Iodine collected on these filter elements was determined by radio-gas chromatography. When the sodium sample burned in the atmosphere of air at room temperature, the release fractions observed were 6∼33% for sodium and 1∼20% for iodine added in the sodium. The release iodine was present in aerosol at a ratio of 98%, and the remainder in the gas form. The release fraction of iodine trended to decrease as oxygen concentration and humidity in the atmosphere increased. No organic iodide was detected in the combustion products. (author)

Critical review of controlled release packaging to improve food safety and quality.

Science.gov (United States)

Chen, Xi; Chen, Mo; Xu, Chenyi; Yam, Kit L

2018-03-19

Controlled release packaging (CRP) is an innovative technology that uses the package to release active compounds in a controlled manner to improve safety and quality for a wide range of food products during storage. This paper provides a critical review of the uniqueness, design considerations, and research gaps of CRP, with a focus on the kinetics and mechanism of active compounds releasing from the package. Literature data and practical examples are presented to illustrate how CRP controls what active compounds to release, when and how to release, how much and how fast to release, in order to improve food safety and quality.

Arct'Alg release from hydrogel membranes

International Nuclear Information System (INIS)

Amaral, Renata H.; Rogero, Sizue O.; Shihomatsu, Helena M.; Lugao, Ademar B.

2009-01-01

The hydrogel properties make them attractive for a variety of biomedical and pharmaceutical applications, primarily in drug delivery system. Synthetic hydrogels have been studied to develop new devices for drugs or cosmetic active agents release. Arct'Alg R is an extract derived from red algae biomass which has antioxidant, anti-inflammatory and tissue regeneration stimulant properties. This extract was incorporated to poly(N-vinyl pyrrolidone) (PVP) and poly(vinyl alcohol) (PVA) hydrogel membranes obtained by gamma rays crosslinking technique. The ionizing radiation presents the advantage to occur polymerization and sterilization simultaneously in the same process. The aim of this work was the in vitro release kinetic study of Arct'Alg R from hydrogel membranes during 24 hours to verify the possibility of use in cosmetic and dermatological treatments. Results showed that about 50% and 30% of incorporated Arct'Alg R was released from PVP and PVA hydrogel membrane devices respectively. (author)

Formulation development and optimization of sustained release matrix tablet of Itopride HCl by response surface methodology and its evaluation of release kinetics.

Science.gov (United States)

Bose, Anirbandeep; Wong, Tin Wui; Singh, Navjot

2013-04-01

The objective of this present investigation was to develop and formulate sustained release (SR) matrix tablets of Itopride HCl, by using different polymer combinations and fillers, to optimize by Central Composite Design response surface methodology for different drug release variables and to evaluate drug release pattern of the optimized product. Sustained release matrix tablets of various combinations were prepared with cellulose-based polymers: hydroxy propyl methyl cellulose (HPMC) and polyvinyl pyrolidine (pvp) and lactose as fillers. Study of pre-compression and post-compression parameters facilitated the screening of a formulation with best characteristics that underwent here optimization study by response surface methodology (Central Composite Design). The optimized tablet was further subjected to scanning electron microscopy to reveal its release pattern. The in vitro study revealed that combining of HPMC K100M (24.65 MG) with pvp(20 mg)and use of LACTOSE as filler sustained the action more than 12 h. The developed sustained release matrix tablet of improved efficacy can perform therapeutically better than a conventional tablet.

Radioactive contamination in Arctic - present situation and future challenges

International Nuclear Information System (INIS)

Strand, Per

2002-01-01

There is currently a focus on radioactivity and the Arctic region. The reason for this is probably the high number of nuclear sources in parts of the Arctic and the vulnerability of Arctic systems to radioactive contamination. The Arctic environment is also perceived as a wilderness and the need for the protection of this wilderness against contamination is great. In the last decade information has also been released concerning the nuclear situation which has caused concern in many countries. Due to such concerns, the International Arctic Environmental Protection Strategy (IAEPS) was launched in 1991 and the Arctic Monitoring and Assessment Programme (AMAP) was established. AMAP is undertaking an assessment of the radioactive contamination of the Arctic and its radiological consequences. In 1996 IAEPS became part of the Arctic Council. AMAP presented one main report in 1997 and another in 1998. There are also several other national, bilateral and international programmes in existence which deal with this issue. This paper summarises some of current knowledge about sources of radioactive contamination, vulnerability, exposure of man, and potential sources for radioactive contamination within Arctic and some views on the future needs for work concerning radioactivity in Arctic. (au)

Effectiveness of water release as mitigation for hydroelectric impacts to fish

International Nuclear Information System (INIS)

Lewis, A.F.; Mitchell, A.C.

1995-01-01

Utility companies release water to mitigate the effects of hydroelectric projects on fish habitats. Utility companies, government agencies, and research communities in Canada, the US, Europe, New Zealand, and Australia were surveyed as part of a Canadian Electrical Association study to evaluate the effectiveness of water release as a mitigation. Respondents identified only 28 projects in which water was released specifically to protect fish habitats. Fewer than half of these projects (12) were judged as being effective. Six case histories with preimpact assessment and postimpact monitoring were reviewed. In four cases fish habitat or fish populations or both were maintained; in two cases they were not. The effectiveness of water release differed among rivers and fish species, and was greatest when designed to meet the habitat requirements of each life-history stage. A review of the literature did not support the theory that a particular fraction of the mean annual flow provides the bet fish habitat. Although smaller changes in the flow regime had smaller effects, increasing minimum flows above those historically observed did not necessarily increase fish production

Modelling isothermal fission gas release

International Nuclear Information System (INIS)

Uffelen, P. van

2002-01-01

The present paper presents a new fission gas release model consisting of two coupled modules. The first module treats the behaviour of the fission gas atoms in spherical grains with a distribution of grain sizes. This module considers single atom diffusion, trapping and fission induced re-solution of gas atoms associated with intragranular bubbles, and re-solution from the grain boundary into a few layers adjacent to the grain face. The second module considers the transport of the fission gas atoms along the grain boundaries. Four mechanisms are incorporated: diffusion controlled precipitation of gas atoms into bubbles, grain boundary bubble sweeping, re-solution of gas atoms into the adjacent grains and gas flow through open porosity when grain boundary bubbles are interconnected. The interconnection of the intergranular bubbles is affected both by the fraction of the grain face occupied by the cavities and by the balance between the bubble internal pressure and the hydrostatic pressure surrounding the bubbles. The model is under validation. In a first step, some numerical routines have been tested by means of analytic solutions. In a second step, the fission gas release model has been coupled with the FTEMP2 code of the Halden Reactor Project for the temperature distribution in the pellets. A parametric study of some steady-state irradiations and one power ramp have been simulated successfully. In particular, the Halden threshold for fission gas release and two simplified FUMEX cases have been computed and are summarised. (author)

FREVAP-6, Metal Fission Products Release from HTGR Fuel Elements

International Nuclear Information System (INIS)

Pierce, V.H.

2005-01-01

1 - Description of problem or function: The FREVAP type of code for estimating the release of longer-lived metallic fission products from HTGR fuel elements has been developed to take into account the combined effects of the retention of metallic fission products by fuel particles and the rather strong absorption of these fission products by the graphite of the fuel elements. Release calculations are made on the basis that the loss of fission product nuclides such as strontium, cesium, and barium is determined by their evaporation from the graphite surfaces and their transpiration induced by the flowing helium coolant. The code is devised so that changes of fission rate (fuel element power), fuel temperature, and graphite temperature may be incorporated into the calculation. Temperature is quite important in determining release because, in general, both release from fuel particles and loss by evaporation (transpiration) vary exponentially with the reciprocal of the absolute temperature. NESC0301/02: This version differs from the previous one in the following points: The source and output files were converted from BCD to ASCII coding. 2 - Method of solution: A problem is defined as having a one-dimensional segment made up of three parts - (1) the fission product source (fuel particles) in series with, (2) a non-source and absorption part (element graphite) and (3) a surface for evaporation to the coolant (graphite-helium interface). More than one segment may be connected (possibly segments stacked axially) by way of the coolant. At any given segment, a continuity equation is solved assuming equilibrium between the source term, absorption term, evaporation at coolant interface and the partial pressure of the fission product isotope in the coolant. 3 - Restrictions on the complexity of the problem - Maxima of: 5 isotopes; 10 time intervals for time-dependent variable; 49 segments (times number of isotopes); 5 different output print time-steps

Statistical Optimization of Sustained Release Venlafaxine HCI Wax Matrix Tablet.

Science.gov (United States)

Bhalekar, M R; Madgulkar, A R; Sheladiya, D D; Kshirsagar, S J; Wable, N D; Desale, S S

2008-01-01

The purpose of this research was to prepare a sustained release drug delivery system of venlafaxine hydrochloride by using a wax matrix system. The effects of bees wax and carnauba wax on drug release profile was investigated. A 3(2) full factorial design was applied to systemically optimize the drug release profile. Amounts of carnauba wax (X(1)) and bees wax (X(2)) were selected as independent variables and release after 12 h and time required for 50% (t(50)) drug release were selected as dependent variables. A mathematical model was generated for each response parameter. Both waxes retarded release after 12 h and increases the t(50) but bees wax showed significant influence. The drug release pattern for all the formulation combinations was found to be approaching Peppas kinetic model. Suitable combination of two waxes provided fairly good regulated release profile. The response surfaces and contour plots for each response parameter are presented for further interpretation of the results. The optimum formulations were chosen and their predicted results found to be in close agreement with experimental findings.

Predictive property models for use in design of controlled release of pesticides

DEFF Research Database (Denmark)

Suné, Nuria Muro; Gani, Rafiqul; Bell, G.

2005-01-01

A model capable of predicting the release of an Active Ingredient (AI) from a specific device would be very useful in the field of pesticide controlled release technology for design purposes. For the release of an AI from a microcapsule a mathematical model is briefly presented here, as an introd...

FACTORS AFFECTING THE RELEASE RATE OF A HIGHLY SOLUBLE DRUG FROM A PROGRAMMED RELEASE MEGALOPOROUS SYSTEM

NARCIS (Netherlands)

VANDERVEEN, C; MENGER, NR; LERK, CF

The present study reports on the successful incorporation of a highly soluble drug, procaine HCl, in a programmed-release megaloporous system. This solid two-phase system is composed of housing phase matrix granules (HMG), controlling liquid penetration into the system, and of restraining phase

Acetylcholine release and inhibitory interneuron activity in hippocampal CA1

Directory of Open Access Journals (Sweden)

A. Rory McQuiston

2014-09-01

Full Text Available Acetylcholine release in the central nervous system (CNS has an important role in attention, recall and memory formation. One region influenced by acetylcholine is the hippocampus, which receives inputs from the medial septum and diagonal band of Broca complex (MS/DBB. Release of acetylcholine from the MS/DBB can directly affect several elements of the hippocampus including glutamatergic and GABAergic neurons, presynaptic terminals, postsynaptic receptors and astrocytes. A significant portion of acetylcholine’s effect likely results from the modulation of GABAergic inhibitory interneurons, which have crucial roles in controlling excitatory inputs, synaptic integration, rhythmic coordination of principal neurons and outputs in the hippocampus. Acetylcholine affects interneuron function in large part by altering their membrane potential via muscarinic and nicotinic receptor activation. This minireview describes recent data from mouse hippocampus that investigated changes in CA1 interneuron membrane potentials following acetylcholine release. The interneuron subtypes affected, the receptor subtypes activated, and the potential outcome on hippocampal CA1 network function is discussed.

Pramipexole Extended Release: A Novel Treatment Option in Parkinson's Disease

Directory of Open Access Journals (Sweden)

Wolfram Eisenreich

2010-01-01

Full Text Available Pramipexole, the most commonly prescribed dopamine agonist worldwide, meanwhile serves as a reference substance for evaluation of new drugs. Based on numerous clinical data and vast experiences, efficacy and safety profiles of this non-ergoline dopamine agonist are well characterized. Since October 2009, an extended-release formulation of pramipexole has been available for symptomatic treatment of Parkinson's disease. Pramipexole administration can be cut down from three times to once a day due to the newly developed extended-release formulation. This is considerable progress in regard to minimizing pill burden and enhancing compliance. Moreover, the 24 h continuous drug release of the once-daily extended-release formulation results in fewer fluctuations in plasma concentrations over time compared to immediate-release pramipexole, given three times daily. The present study summarizes pharmacokinetics and all essential pharmacological and clinical characteristics of the extended-release formulation. In addition, it provides all study data, available so far, with regard to transition and de-novo administration of extended-release formulation for patients with Parkinson's disease. It further compares efficacy and safety data of immediate-release pramipexole with the extended-release formulation of pramipexole.

Saiboku-to, a Kampo herbal medicine, inhibits LTC4 release from eosinophils

Directory of Open Access Journals (Sweden)

Koichi Hirai

1998-01-01

Full Text Available Saiboku-to (TJ-96, a traditional Kampo herbal formation, has been used in the treatment of bronchial asthma in Japan as an anti-allergy herbal medicine. We investigated the effect of TJ-96 on leukotriene (LTC4 release from eosinophils and basophils isolated from healthy volunteers. Pre-incubation of eosinophils with TJ-96 inhibited ionophore- or formyl-methionyl-leucyl-phenylalanine (FMLP-induced LTC4 generation by eosinophils in a dose-dependent fashion. The TJ-96 was more potent in the release by ionophore (IC50 = 60 mg/mL than the release induced by FMLP (IC50 = 300 mg/mL. Maximal inhibition was observed when eosinophils were pretreated with TJ-96 for 5 min. Although TJ-96 at high concentrations inhibited IgE-mediated histamine release from human basophils, inhibition of IgE-mediated LTC4 release was not statistically significant. The potent inhibitory activity was found in the extract of Glycyrrhiza root, one of the herbal components of TJ-96, but the inhibitory effects were not due to either glycyrrhizin or liquiritin, the main elements of the Glycyrrhiza root. These results raise the possibility that the clinical efficacy of TJ-96 is derived, at least in part, from its potent inhibitory effect on LTC4 release from eosinophils.

Control of synthesis and release of radioactive acetylcholine in brain slices from the rat. Effects of neurotropic drugs

Science.gov (United States)

Grewaal, D. S.; Quastel, J. H.

1973-01-01

1. Studies of the synthesis and release of radioactive acetylcholine in rat brain-cortex slices incubated in Locke–bicarbonate–[U-14C]glucose media, containing paraoxon as cholinesterase inhibitor, revealed the following phenomena: (a) dependence of K+-or protoveratrine-stimulated acetylcholine synthesis and release on the presence of Na+ and Ca2+ in the incubation medium, (b) enhanced release of radioactive acetylcholine by substances that promote depolarization at the nerve cell membrane (e.g. high K+, ouabain, protoveratrine, sodium l-glutamate, high concentration of acetylcholine), (c) failure of acetylcholine synthesis to keep pace with acetylcholine release under certain conditions (e.g. the presence of ouabain or lack of Na+). 2. Stimulation by K+ of radioactive acetylcholine synthesis was directly proportional to the external concentration of Na+, but some synthesis and release of radioactive acetylcholine occurred in the absence of Na+ as well as in the absence of Ca2+. 3. The Na+ dependence of K+-stimulated acetylcholine synthesis was partly due to suppression of choline transport, as addition of small concentrations of choline partly neutralized the effect of Na+ lack, and partly due to the suppression of the activity of the Na+ pump. 4. Protoveratrine caused a greatly increased release of radioactive acetylcholine without stimulating total radioactive acetylcholine synthesis. Protoveratrine was ineffective in the absence of Ca2+ from the incubation medium. It completely blocked K+ stimulation of acetylcholine synthesis and release. 5. Tetrodotoxin abolished the effects of protoveratrine on acetylcholine release. It had blocking effects (partial or complete) on the action of high K+, sodium l-glutamate and lack of Ca2+ on acetylcholine synthesis and release. 6. Unlabelled exogenous acetylcholine did not diminish the content of labelled tissue acetylcholine, derived from labelled glucose, suggesting that no exchange with vesicular acetylcholine took

Excessive nickel release from mobile phones--a persistent cause of nickel allergy and dermatitis.

Science.gov (United States)

Jensen, Peter; Johansen, Jeanne D; Zachariae, Claus; Menné, Torkil; Thyssen, Jacob P

2011-12-01

Despite the political intention to limit nickel allergy and dermatitis in Europeans, nickel allergy remains frequent. There are several explanations for the persistence of nickel allergy and dermatitis, including the increasing use of mobile phones. Before regulation of nickel release from mobile phones, we showed that eight (19.5%) of 41 mobile phones marketed in Denmark between 2003 and 2007 released nickel in concentrations that may result in nickel allergy and dermatitis. In 2009, the EU Nickel Directive was revised to include nickel-releasing mobile phones. To investigate the proportion of mobile phones sold in Denmark that release nickel after regulation. Metallic parts from 50 randomly selected mobile phones currently for sale in Denmark were tested for nickel release by use of the dimethylglyoxime (DMG)-nickel spot test. Nine (18%) phones showed at least one positive DMG test reaction and two phones had more than one DMG test-positive spot. Apparently, the proportion of mobile phones with significant nickel release remains unchanged, despite the 2009 revision of the EU Nickel Directive. We encourage manufacturers to measure nickel release from metallic components used in the assembly of mobile phones to ensure safe products. © 2011 John Wiley & Sons A/S.

CMS Partial Releases Model, Tools, and Applications. Online and Framework-Light Releases

CERN Document Server

Jones, Christopher D; Meschi, Emilio; Shahzad Muzaffar; Andreas Pfeiffer; Ratnikova, Natalia; Sexton-Kennedy, Elizabeth

2009-01-01

The CMS Software project CMSSW embraces more than a thousand packages organized in subsystems for analysis, event display, reconstruction, simulation, detector description, data formats, framework, utilities and tools. The release integration process is highly automated by using tools developed or adopted by CMS. Packaging in rpm format is a built-in step in the software build process. For several well-defined applications it is highly desirable to have only a subset of the CMSSW full package bundle. For example, High Level Trigger algorithms that run on the Online farm, and need to be rebuilt in a special way, require no simulation, event display, or analysis packages. Physics analysis applications in Root environment require only a few core libraries and the description of CMS specific data formats. We present a model of CMS Partial Releases, used for preparation of the customized CMS software builds, including description of the tools used, the implementation, and how we deal with technical challenges, suc...

Sintering of wax for controlling release from pellets.

Science.gov (United States)

Singh, Reena; Poddar, S S; Chivate, Amit

2007-09-14

The purpose of the present study was to investigate incorporation of hydrophobic (ie, waxy) material into pellets using a thermal sintering technique and to evaluate the pellets in vitro for controlled release. Pellets prepared by extrusion-spheronization technology were formulated with a water-soluble drug, microcrystalline cellulose, and carnauba wax. Powdered carnauba wax (4%-20%) prepared by grinding or by emulsification was studied with an attempt to retard the drug release. The inclusion of ground or emulsified carnauba wax did not sustain the release of theophylline for more than 3 hours. Matrix pellets of theophylline prepared with various concentrations of carnauba wax were sintered thermally at various times and temperatures. In vitro drug release profiles indicated an increase in drug release retardation with increasing carnauba wax concentration. Pellets prepared with ground wax showed a higher standard deviation than did those prepared with emulsified wax. There was incomplete release at the end of 12 hours for pellets prepared with 20% ground or emulsified wax. The sintering temperature and duration were optimized to allow for a sustained release lasting at least 12 hours. The optimized temperature and duration were found to be 100 degrees C and 140 seconds, respectively. The sintered pellets had a higher hydrophobicity than did the unsintered pellets. Scanning electron micrographs indicated that the carnauba wax moved internally, thereby increasing the surface area of wax within the pellets.

Hanford Tank 241-C-106: Impact of Cement Reactions on Release of Contaminants from Residual Waste

International Nuclear Information System (INIS)

Deutsch, William J.; Krupka, Kenneth M.; Lindberg, Michael J.; Cantrell, Kirk J.; Brown, Christopher F.; Schaef, Herbert T.

2006-01-01

The CH2M HILL Hanford Group, Inc. (CH2M HILL) is producing risk/performance assessments to support the closure of single-shell tanks at the U.S. Department of Energy's Hanford Site. As part of this effort, staff at Pacific Northwest National Laboratory were asked to develop release models for contaminants of concern that are present in residual sludge remaining in tank 241-C-106 (C-106) after final retrieval of waste from the tank. Initial work to produce release models was conducted on residual tank sludge using pure water as the leaching agent. The results were reported in an earlier report. The decision has now been made to close the tanks after waste retrieval with a cementitious grout to minimize infiltration and maintain the physical integrity of the tanks. This report describes testing of the residual waste with a leaching solution that simulates the composition of water passing through the grout and contacting the residual waste at the bottom of the tank.

Tritium release of titan-tritium layers in air, aqueous solutions and living organisms of animals

International Nuclear Information System (INIS)

Biro, J.; Feher, I.; Mate, L.; Varga, L.

1978-01-01

Samples containing 400-1100 MBq (10-30 mCi) tritium were prepared and the effect of storage time on tritium release was followed. In 250 days one thousandth of the tritium was released in aqueous solution; in air the ratio of release per hour fell in the range of 10 -6 -10 -7 . Ti-T plates with different storage times were surgically placed in the abdomen of rats. Their tritium release dropped with time and the activity appearing in the circulation was lower than that of plates with 5-6 orders of magnitude. Checking the tritium incorporation of neutron generator operators it must be held in mind that only a minor part of tritium can be detected by the measurement of the tritium content of urine. (author)

Free-space optics technology employed in an UMTS release 4 bearer independent core network access part

Science.gov (United States)

Bibac, Ionut

2005-08-01

The UMTS Bearer Independent Core Network program introduced the 3rd Generation Partnership Program Release 4 BICN architecture into the legacy UMTS TDM-switched network. BICN is the application of calI server archltecture for voice and circuit switched data, enabling the provisioning of traditional circuit-switched services using a packet-switched transport network. Today"s business climate has made it essential for service providers to develop a comprehensive networking strategy that means introduction of RCBICN networks. The R4-BICN solution to the evolution of the Core Network in UMTS will enable operators to significantly reduce the capital and operational costs of delivering both traditional voice sewices and new multimedia services. To build the optical backbone, which can support the third generation (3G) packetized infrastructure, the operators could choose a fibre connection, or they could retain the benefits of a wireless connectivity by using a FSO - Free Space Optical lmk, the only wireless technology available that is capable of achieving data rates up to 2.4 Gbit/s. FSO offers viable alternatives for both core transmission networks and for replacing microwaves links in NodeB - RNC access networks. The paper and presentation aim to demonstrate the manner in which FSO products and networks are employed into R4-BICN design solutions.

Hot neutron stars at birth and energy release

International Nuclear Information System (INIS)

Takatsuka, Tatsuyuki

1994-01-01

For the discussion of hot neutron stars at birth, it is necessary to calculate the equation of state for a so-called 'supernova matter' consisting of a neutron-rich nuclear matter and degenerated leptons. One of the aims of this paper is to obtain the realistic results for the equation of state. In 10-20s after the birth, new born hot neutron stars are cooled down by neutrino diffusion process, and gradually contract to usual cold neutron starts. It is another aim of this paper to determine how much energy is released during this cooling stage. The points to which attention was paid are explained. A three-nucleon interaction was introduced phenomenologically, as a two-nucleon interaction is insufficient to satisfy the empirical saturation property of symmetric nuclear matters. The separation of uncertain part from well-known part has the merit to clarify the dependence of the results on the present theoretical uncertainties. The validity of the simplified calculation as an approximation for the exact calculation is discussed. The results by both calculations were compared for the case of hot symmetric nuclear matters. The comparison of the density profiles for a hot neutron star and a cold neutron star is shown. The binding energy for hot and cold neutron stars was plotted. These results are examined. (K.I.)

Fate of corrosion products released from stainless steel in marine sediments and seawater. Part 4: Hatteras abyssal red clay

Energy Technology Data Exchange (ETDEWEB)

Schmidt, R.L.

1982-07-01

A study in which neutron-activated 347 stainless steel was exposed to surficial sediment from a site in the Hatteras Abyssal Plain of the Northwest Atlantic Ocean is described. This sediment consists of approx. 20% CaCO/sub 3/, which could lead to the formation of calcareous scale on the metal surface and reduce the corrosion rate. The distribution of indigenous metals among different chemical fractions shows that extractable Cr, Mn, Fe, Co, and Zn were associated with amorphous Mn and Fe oxides. Most of the remaining extractable Cr, and about a third of the extractable Cu appear to have been weakly complexed. Major fractions (25 to 36%) of extractable Mn, Co and Ni were present as adsorbed cations. Organic complexation appears to account for a large amount of extractable Fe, Ni, Cu and Zn. Neutron-activated 347 stainless steel specimens were exposed to sediment slurry under aerobic and non-oxygenated conditions for a period of 94 days. The redox potential measurements for air-sparged and N/sub 2/, CO/sub 2/-sparged sediment slurries were +410 and +60 mv, respectively. The presence of 0/sub 2/ produced increased amounts of corrosion products. Chemical extraction showed that relatively labile substances constituted about 84% of the /sup 60/Co activity released in aerated sediment. Relatively labile substances constitute about 82% of the total /sup 60/Co activity released under non-oxygenated conditions. A large fraction of /sup 60/Co which was in the soluble or easily dissolved forms under non-oxygenated conditions appears to have been more strongly adsorbed to the sediment under aerated conditions.

Sintering of wax for controlling release from pellets

OpenAIRE

Singh, Reena; Poddar, S. S.; Chivate, Amit

2007-01-01

The purpose of the present study was to investigate incorporation of hydrophobic (ie, waxy) material into pellets using a thermal sintering technique and to evaluate the pellets in vitro for controlled release. Pellets prepared by extrusion-spheronization technology were formulated with a water-soluble drug, microcrystalline cellulose, and carnauba wax. Powdered carnauba wax (4%–20%) prepared by grinding or by emulsification was studied with an attempt to retard the drug release. The inclusio...

Stretch-induced Ca2+ independent ATP release in hippocampal astrocytes.

Science.gov (United States)

Xiong, Yingfei; Teng, Sasa; Zheng, Lianghong; Sun, Suhua; Li, Jie; Guo, Ning; Li, Mingli; Wang, Li; Zhu, Feipeng; Wang, Changhe; Rao, Zhiren; Zhou, Zhuan

2018-02-28

Similar to neurons, astrocytes actively participate in synaptic transmission via releasing gliotransmitters. The Ca 2+ -dependent release of gliotransmitters includes glutamate and ATP. Following an 'on-cell-like' mechanical stimulus to a single astrocyte, Ca 2+ independent single, large, non-quantal, ATP release occurs. Astrocytic ATP release is inhibited by either selective antagonist treatment or genetic knockdown of P2X7 receptor channels. Our work suggests that ATP can be released from astrocytes via two independent pathways in hippocampal astrocytes; in addition to the known Ca 2+ -dependent vesicular release, larger non-quantal ATP release depends on P2X7 channels following mechanical stretch. Astrocytic ATP release is essential for brain functions such as synaptic long-term potentiation for learning and memory. However, whether and how ATP is released via exocytosis remains hotly debated. All previous studies of non-vesicular ATP release have used indirect assays. By contrast, two recent studies report vesicular ATP release using more direct assays. In the present study, using patch clamped 'ATP-sniffer cells', we re-investigated astrocytic ATP release at single-vesicle resolution in hippocampal astrocytes. Following an 'on-cell-like' mechanical stimulus of a single astrocyte, a Ca 2+ independent single large non-quantal ATP release occurred, in contrast to the Ca 2+ -dependent multiple small quantal ATP release in a chromaffin cell. The mechanical stimulation-induced ATP release from an astrocyte was inhibited by either exposure to a selective antagonist or genetic knockdown of P2X7 receptor channels. Functional P2X7 channels were expressed in astrocytes in hippocampal brain slices. Thus, in addition to small quantal ATP release, larger non-quantal ATP release depends on P2X7 channels in astrocytes. © 2018 The Authors. The Journal of Physiology © 2018 The Physiological Society.

Proceedings of the Scientific Meeting and Presentation on Basic Research in Nuclear of the Science and Technology part I : Physics and Nuclear Reactor

International Nuclear Information System (INIS)

Kamsul Abraha; Yateman Arryanto; Sri Jauhari S; Agus Taftazani; Kris Tri Basuki; Djoko Sardjono, Ign.; Sukarsono, R.; Samin; Syarip; Suryadi, MS; Sardjono, Y.; Tri Mardji Atmono; Dwiretnani Sudjoko; Tjipto Sujitno, BA.

2007-08-01

The Scientific Meeting and Presentation on Basic Research in Nuclear Science and Technology is a routine activity held by Centre for Accelerator Technology and Material Process, National Nuclear Energy Agency, for monitoring the research activity which achieved in National Nuclear Energy Agency. The Meeting was held in Yogyakarta on July 10, 2007. The proceedings contains papers presented on the meeting about Physics and Nuclear Reactor and there are 52 papers. The proceedings is the first part of the three parts which published in series. (PPIN)

Diffusive spatio-temporal noise in a first-passage time model for intracellular calcium release

KAUST Repository

Flegg, Mark B.; Rüdiger, Sten; Erban, Radek

2013-01-01

The intracellular release of calcium from the endoplasmic reticulum is controlled by ion channels. The resulting calcium signals exhibit a rich spatio-temporal signature, which originates at least partly from microscopic fluctuations. While

The application of release models to the interpretation of rare gas coolant activities

International Nuclear Information System (INIS)

Wise, C.

1985-01-01

Much research is carried out into the release of fission products from UO 2 fuel and from failed pins. A significant application of this data is to define models of release which can be used to interpret measured coolant activities of rare gas isotopes. Such interpretation is necessary to extract operationally relevant parameters, such as the number and size of failures in the core and the 131 I that might be released during depressurization faults. The latter figure forms part of the safety case for all operating CAGRs. This paper describes and justifies the models which are used in the ANAGRAM program to interpret CAGR coolant activities, highlighting any remaining uncertainties. The various methods by which the program can extract relevant information from the measurements are outlined, and examples are given of the analysis of coolant data. These analyses point to a generally well understood picture of fission gas release from low temperature failures. Areas of higher temperature release are identified where further research would be beneficial to coolant activity analysis. (author)

Modified hydrotalcite-like compounds as active fillers of biodegradable polymers for drug release and food packaging applications.

Science.gov (United States)

Costantino, Umberto; Nocchetti, Morena; Tammaro, Loredana; Vittoria, Vittoria

2012-11-01

This review treats the recent patents and related literature, mainly from the Authors laboratories, on biomedical and food packaging applications of nano-composites constituted of biodegradable polymers filled with micro or nano crystals of organically modified Layered Double Hydroxides of Hydrotalcite type. After a brief outline of the chemical and structural aspects of Hydrotalcite-like compounds (HTlc) and of their manipulation via intercalation of functional molecular anions to obtain materials for numerous, sometime unexpected applications, the review approaches the theme in three separated parts. Part 1 deals with the synthetic method used to prepare the pristine Mg-Al and Zn-Al HTlc and with the procedures of their functionalization with anti-inflammatory (diclofenac), antibacterial (chloramphenicol hemisuccinate), antifibrinolytic (tranexamic acid) drugs and with benzoates with antimicrobial activity. Procedures used to form (nano) composites of polycaprolactone, used as an example of biodegradable polymer, and functionalized HTlc are also reported. Part 2 discusses a patent and related papers on the preparation and biomedical use of a controlled delivery system of the above mentioned pharmacologically active substances. After an introduction dealing with the recent progress in the field of local drug delivery systems, the chemical and structural aspects of the patented system constituted of a biodegradable polymer and HTlc loaded with the active substances will be presented together with an extensive discussion of the drug release in physiological medium. Part 3 deals with a recent patent and related papers on chemical, structural and release property of antimicrobial species of polymeric films containing antimicrobial loaded HTlc able to act as active packaging for food products prolonging their shelf life.

SRTM Data Release for Africa, Colored Height

Science.gov (United States)

2004-01-01

This color shaded relief image shows the extent of digital elevation data for Africa recently released by the Shuttle Radar Topography Mission (SRTM). This release includes data for all of the continent, plus the island of Madagascar and the Arabian Peninsula. SRTM flew on board the Space Shuttle Endeavour in February 2000 and used an interferometric radar system to map the topography of Earth's landmass between latitudes 56 degrees south and 60 degrees north. The data were processed into geographic 'tiles,' each of which represents one by one degree of latitude and longitude. A degree of latitude measures 111 kilometers (69 miles) north-south, and a degree of longitude measures 111 kilometers or less east-west, decreasing away from the equator. The data are being released to the public on a continent-by-continent basis. This Africa segment includes 3256 tiles, almost a quarter of the total data set. Previous releases covered North America, South America and Eurasia. Forthcoming releases will include Australia plus an 'Islands' release for those islands not included in the continental releases. Together these data releases constitute the world's first high-resolution, near-global elevation model. The resolution of the publicly released data is three arcseconds (1/1,200 of a degree of latitude and longitude), which is about 90 meters (295 feet). Coverage in the current data release extends from 35 degrees north latitude at the southern edge of the Mediterranean to the very tip of South Africa, encompassing a great diversity of landforms. The northern part of the continent consists of a system of basins and plateaus, with several volcanic uplands whose uplift has been matched by subsidence in the large surrounding basins. Many of these basins have been infilled with sand and gravel, creating the vast Saharan lands. The Atlas Mountains in the northwest were created by convergence of the African and Eurasian tectonic plates. The geography of the central latitudes of

Impact of Industrial Releases on Inshas Area

International Nuclear Information System (INIS)

El-Messiry, A.M.; Aly, M.M.

1999-01-01

Two Egyptian research reactors are located within the nuclear research center at Inshas area, 30 km north east of Cairo. This area are crowded by different industrial plants. The releases from them has a hazardous and economical effects on the research center workers and the surrounding inhabitancy. In the present work we study these effects. A meteorological regional specific data is considered all over the year, including a wind rose characterization. The study considered both normal operating conditions and an accidental releases. The results shows that there are a considerable risk due to normal releases in some areas downwind direction of the major releases, and a highly risk in areas subjected to major exposure. Regional maps of emission distribution, economical damage , pollutant concentration are obtained. The study helps to identify solutions to problems of atmospheric protection. It can be used as a decision support for the environmental, economic, and innovation planning at the national levels taking into consideration the national pollution standards and variety of existing emission sources

Formulation and In Vitro, In Vivo Evaluation of Effervescent Floating Sustained-Release Imatinib Mesylate Tablet

Science.gov (United States)

Kadivar, Ali; Kamalidehghan, Behnam; Javar, Hamid Akbari; Davoudi, Ehsan Taghizadeh; Zaharuddin, Nurul Dhania; Sabeti, Bahareh; Chung, Lip Yong; Noordin, Mohamed Ibrahim

2015-01-01

Introduction Imatinib mesylate is an antineoplastic agent which has high absorption in the upper part of the gastrointestinal tract (GIT). Conventional imatinib mesylate (Gleevec) tablets produce rapid and relatively high peak blood levels and requires frequent administration to keep the plasma drug level at an effective range. This might cause side effects, reduced effectiveness and poor therapeutic management. Therefore, floating sustained-release Imatinib tablets were developed to allow the tablets to be released in the upper part of the GIT and overcome the inadequacy of conventional tablets. Methodology Floating sustained-release Imatinib mesylate tablets were prepared using the wet granulation method. Tablets were formulated using Hydroxypropyl Methylcellulose (HPMC K4M), with Sodium alginate (SA) and Carbomer 934P (CP) as release-retarding polymers, sodium bicarbonate (NaHCO3) as the effervescent agent and lactose as a filler. Floating behavior, in vitro drug release, and swelling index studies were conducted. Initial and total drug release duration was compared with a commercial tablet (Gleevec) in 0.1 N HCl (pH 1.2) at 37 ± 0.5°C for 24 hours. Tablets were then evaluated for various physical parameters, including weight variation, thickness, hardness, friability, and drug content. Consequently, 6 months of physical stability studies and in vitro gastro-retentive studies were conducted. Results and Discussion Statistical data analysis revealed that tablets containing a composition of 14.67% w/w HPMC K4M, 10.67%, w/w Na alginate, 1.33%, w/w Carbomer 934P and 9.33%, w/w NaHCO3 produced the most favorable formulation to develop 24-hour sustained-release tablets with optimum floating behavior and satisfactory physicochemical characteristics. Furthermore, in vitro release study revealed that the formulated SR tablet had significantly lower Cmax and higher Tmax compared to the conventional tablet (Gleevec). Thus, formulated SR tablets preserved persistent

Formulation and in vitro, in vivo evaluation of effervescent floating sustained-release imatinib mesylate tablet.

Directory of Open Access Journals (Sweden)

Ali Kadivar

Full Text Available Imatinib mesylate is an antineoplastic agent which has high absorption in the upper part of the gastrointestinal tract (GIT. Conventional imatinib mesylate (Gleevec tablets produce rapid and relatively high peak blood levels and requires frequent administration to keep the plasma drug level at an effective range. This might cause side effects, reduced effectiveness and poor therapeutic management. Therefore, floating sustained-release Imatinib tablets were developed to allow the tablets to be released in the upper part of the GIT and overcome the inadequacy of conventional tablets.Floating sustained-release Imatinib mesylate tablets were prepared using the wet granulation method. Tablets were formulated using Hydroxypropyl Methylcellulose (HPMC K4M, with Sodium alginate (SA and Carbomer 934P (CP as release-retarding polymers, sodium bicarbonate (NaHCO3 as the effervescent agent and lactose as a filler. Floating behavior, in vitro drug release, and swelling index studies were conducted. Initial and total drug release duration was compared with a commercial tablet (Gleevec in 0.1 N HCl (pH 1.2 at 37 ± 0.5°C for 24 hours. Tablets were then evaluated for various physical parameters, including weight variation, thickness, hardness, friability, and drug content. Consequently, 6 months of physical stability studies and in vitro gastro-retentive studies were conducted.Statistical data analysis revealed that tablets containing a composition of 14.67% w/w HPMC K4M, 10.67%, w/w Na alginate, 1.33%, w/w Carbomer 934P and 9.33%, w/w NaHCO3 produced the most favorable formulation to develop 24-hour sustained-release tablets with optimum floating behavior and satisfactory physicochemical characteristics. Furthermore, in vitro release study revealed that the formulated SR tablet had significantly lower Cmax and higher Tmax compared to the conventional tablet (Gleevec. Thus, formulated SR tablets preserved persistent concentration of plasma up to 24 hours

Bcl-2 and Bcl-xL overexpression inhibits cytochrome c release, activation of multiple caspases, and virus release following coxsackievirus B3 infection

International Nuclear Information System (INIS)

Carthy, Christopher M.; Yanagawa, Bobby; Luo Honglin; Granville, David J.; Yang, Decheng; Cheung, Paul; Cheung, Caroline; Esfandiarei, Mitra; Rudin, Charles M.; Thompson, Craig B.; Hunt, David W.C.; McManus, Bruce M.

2003-01-01

Coxsackievirus B3, a cytopathic virus in the family Picornaviridae, induces degenerative changes in host cell morphology. Here we demonstrate cytochrome c release and caspases-2, -3, -6, -7, -8, and -9 processing. Enforced Bcl-2 and Bcl-xL expression markedly reduced release of cytochrome c, presentation of the mitochondrial epitope 7A6, and depressed caspase activation following infection. In comparison, cell death using TRAIL ligand caused caspase-8 processing prior to cytochrome c release and executioner caspases and cell death was only partially rescued by Bcl-2 and Bcl-xL overexpression. Disruption of the mitochondrial inner membrane potential following CVB3 infection was not inhibited by zVAD.fmk treatment. Bcl-2 or Bcl-xL overexpression or zVAD.fmk treatment delayed the loss of host cell viability and decreased progeny virus release following infection. Our data suggest that mitochondrial release of cytochrome c may be an important early event in caspase activation in CVB3 infection, and, as such, may contribute to the loss of host-cell viability and progeny virus release

The state of head injury biomechanics: past, present, and future part 2: physical experimentation.

Science.gov (United States)

Goldsmith, Werner; Monson, Kenneth L

2005-01-01

This presentation is the continuation of the article published in Critical Reviews of Biomedical Engineering, 29(5-6), 2001. That issue contained topics dealing with components and geometry of the human head, classification of head injuries, some early experimental studies, and tolerance considerations. It then dealt with head motion and load characterization, investigations during the period from 1939 to 1966, injury causation and early modeling efforts, the 1966 Head Injury Conference and its sequels, mechanical properties of solid tissues, fluid characterization, and early investigation of the mechanical properties of cranial materials. It continued with a description of the systematic investigations of solid cranial components and structural properties since 1966, fetal cranial properties, analytical head modeling, and numerical solutions of head injury. The paper concluded with experimental dynamic loading of human living and cadaver heads, dynamic loading of surrogate heads, and head injury mechanics. This portion of the paper describes physical head injury experimentation involving animals, primarily primates, human cadavers, volunteers, and inanimate physical models. In order to address the entire domain of head injury biomechanics in the two-part survey, it was intended that this information be supplemented by discussions of head injury tolerance and criteria, automotive and sports safety considerations, and the design of protective equipment, but Professor Goldsmith passed away before these sections could be completed. It is nevertheless anticipated that this attenuated installment will provide, in conjunction with the first part of the survey, a valuable resource for students and practitioners of head injury biomechanics.

Flash release an alternative for releasing complex MEMS devices

NARCIS (Netherlands)

Deladi, S.; Krijnen, Gijsbertus J.M.; Elwenspoek, Michael Curt

2004-01-01

A novel time-saving and cost-effective release technique has been developed and is described. The physical nature of the process is explained in combination with experimental observations. The results of the flash release process are compared with those of freeze-drying and supercritical CO2

Prodigiosin release from an implantable biomedical device: kinetics of localized cancer drug release

International Nuclear Information System (INIS)

Danyuo, Y.; Obayemi, J.D.; Dozie-Nwachukwu, S.; Ani, C.J.; Odusanya, O.S.; Oni, Y.; Anuku, N.; Malatesta, K.; Soboyejo, W.O.

2014-01-01

This paper presents an implantable encapsulated structure that can deliver localized heating (hyperthermia) and controlled concentrations of prodigiosin (a cancer drug) synthesized by bacteria (Serratia marcesce (subsp. marcescens)). Prototypical Poly-di-methyl-siloxane (PDMS) packages, containing well-controlled micro-channels and drug storage compartments, were fabricated along with a drug-storing polymer produced by free radical polymerization of Poly(N-isopropylacrylamide)(PNIPA) co-monomers of Acrylamide (AM) and Butyl-methacrylate (BMA). The mechanisms of drug diffusion of PNIPA-base gels were elucidated. Scanning Electron Microscopy (SEM) was also used to study the heterogeneous porous structure of the PNIPA-based gels. The release exponents, n, of the gels were found to between 0.5 and 0.7. This is in the range expected for Fickian (n = 0.5). Deviation from Fickian diffusion was also observed (n > 0.5) diffusion. The gel diffusion coefficients were shown to vary between 2.1 × 10 −12 m 2 /s and 4.8 × 10 −6 m 2 /s. The implications of the results are then discussed for the localized treatment of cancer via hyperthermia and the controlled delivery of prodigiosin from encapsulated PNIPA-based devices. - Highlights: • Fabricated thermo-sensitive hydrogels for localized drug release from an implantable biomedical device. • Determined the cancer drug diffusion mechanisms of PNIPA-co-AM copolymer hydrogel. • Encapsulated PNIPA-based hydrogels in PDMS capsules for controlled drug delivery. • Established the kinetics of drug release from gels and channels in an implantable biomedical device. • Demonstrated the potential for the controlled release of prodigiosin (PG) as an anticancer drug

Prodigiosin release from an implantable biomedical device: kinetics of localized cancer drug release

Energy Technology Data Exchange (ETDEWEB)

Danyuo, Y.; Obayemi, J.D.; Dozie-Nwachukwu, S. [Department of Materials Science and Engineering, African University of Science and Technology (AUST), Abuja, Federal Capital Territory (Nigeria); Ani, C.J. [Department of Theoretical Physics, African University of Science and Technology (AUST), Abuja, Federal Capital Territory (Nigeria); Odusanya, O.S. [Biotechnology and Genetic Engineering Advanced Laboratory, Sheda Science and Technology Complex (SHESTCO), Abuja, Federal Capital Territory (Nigeria); Oni, Y. [Department of Chemistry, Bronx Community College, New York, NY (United States); Anuku, N. [Department of Chemistry, Bronx Community College, New York, NY (United States); Princeton Institute for the Science and Technology of Materials (PRISM), 70 Prospect Street, Princeton, NJ 08544 (United States); Malatesta, K. [Department of Chemistry, Bronx Community College, New York, NY (United States); Soboyejo, W.O., E-mail: soboyejo@princeton.edu [Department of Materials Science and Engineering, African University of Science and Technology (AUST), Abuja, Federal Capital Territory (Nigeria); Princeton Institute for the Science and Technology of Materials (PRISM), 70 Prospect Street, Princeton, NJ 08544 (United States); Department of Mechanical and Aerospace Engineering 1 Olden Street, Princeton, NJ 08544 (United States)

2014-09-01

This paper presents an implantable encapsulated structure that can deliver localized heating (hyperthermia) and controlled concentrations of prodigiosin (a cancer drug) synthesized by bacteria (Serratia marcesce (subsp. marcescens)). Prototypical Poly-di-methyl-siloxane (PDMS) packages, containing well-controlled micro-channels and drug storage compartments, were fabricated along with a drug-storing polymer produced by free radical polymerization of Poly(N-isopropylacrylamide)(PNIPA) co-monomers of Acrylamide (AM) and Butyl-methacrylate (BMA). The mechanisms of drug diffusion of PNIPA-base gels were elucidated. Scanning Electron Microscopy (SEM) was also used to study the heterogeneous porous structure of the PNIPA-based gels. The release exponents, n, of the gels were found to between 0.5 and 0.7. This is in the range expected for Fickian (n = 0.5). Deviation from Fickian diffusion was also observed (n > 0.5) diffusion. The gel diffusion coefficients were shown to vary between 2.1 × 10{sup −12} m{sup 2}/s and 4.8 × 10{sup −6} m{sup 2}/s. The implications of the results are then discussed for the localized treatment of cancer via hyperthermia and the controlled delivery of prodigiosin from encapsulated PNIPA-based devices. - Highlights: • Fabricated thermo-sensitive hydrogels for localized drug release from an implantable biomedical device. • Determined the cancer drug diffusion mechanisms of PNIPA-co-AM copolymer hydrogel. • Encapsulated PNIPA-based hydrogels in PDMS capsules for controlled drug delivery. • Established the kinetics of drug release from gels and channels in an implantable biomedical device. • Demonstrated the potential for the controlled release of prodigiosin (PG) as an anticancer drug.

Final voluntary release assessment/corrective action report

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-11-12

The US Department of Energy, Carlsbad Area Office (DOE-CAO) has completed a voluntary release assessment sampling program at selected Solid Waste Management Units (SWMUs) at the Waste Isolation Pilot Plant (WIPP). This Voluntary Release Assessment/Corrective Action (RA/CA) report has been prepared for final submittal to the Environmental protection Agency (EPA) Region 6, Hazardous Waste Management Division and the New Mexico Environment Department (NMED) Hazardous and Radioactive Materials Bureau to describe the results of voluntary release assessment sampling and proposed corrective actions at the SWMU sites. The Voluntary RA/CA Program is intended to be the first phase in implementing the Resource Conservation and Recovery Act (RCRA) Facility Investigation (RFI) and corrective action process at the WIPP. Data generated as part of this sampling program are intended to update the RCRA Facility Assessment (RFA) for the WIPP (Assessment of Solid Waste Management Units at the Waste Isolation Pilot Plant), NMED/DOE/AIP 94/1. This Final Voluntary RA/CA Report documents the results of release assessment sampling at 11 SWMUs identified in the RFA. With this submittal, DOE formally requests a No Further Action determination for these SWMUs. Additionally, this report provides information to support DOE`s request for No Further Action at the Brinderson and Construction landfill SWMUs, and to support DOE`s request for approval of proposed corrective actions at three other SWMUs (the Badger Unit Drill Pad, the Cotton Baby Drill Pad, and the DOE-1 Drill Pad). This information is provided to document the results of the Voluntary RA/CA activities submitted to the EPA and NMED in August 1995.

Controlled release of tetracycline-HCl from halloysite-polymer composite films.

Science.gov (United States)

Ward, Christopher J; Song, Shang; Davis, Edward W

2010-10-01

The first direct comparison between two common methods for loading halloysite with a small molecule for controlled release is presented. While the methods differ in the degree of simplicity, they provide essentially the same level of loading and release kinetics. A tentative explanation of the "burst" effect often seen in the release of low molecular weight molecules from halloysite is provided. The ability of halloysite to mediate the release rate of a water soluble drug, tetracycline, from solution cast polyvinyl alcohol and polymethyl methacrylate films was evaluated. In some films, montmorillonite was also incorporated. The addition of montmorillonite to solutions used to cast tetracycline containing films significantly reduced the release rate from the dried films. The same overall effect was seen when the drug was loaded into halloysite prior to preparation of the films. In both cases, the release was best fit with the simple Higuchi model. However, when montmorillonite was added to solutions of polyvinyl alcohol and drug loaded halloysite the release profiles were better fit by the Ritgar-Peppas model for anomalous transport. Release from polymethyl methacrylate was reduced by a factor of three by incorporating the drug in halloysite prior to producing the films.

Role of hemolysis in potassium release by iodinated contrast medium

Energy Technology Data Exchange (ETDEWEB)

Hayakawa, K.; Nakamura, T.; Shimizu, Y. [Department of Radiology, Kyoto City Hospital (Japan)

1999-09-01

It has been demonstrated that an iodinated contrast medium (CM) causes release of potassium into blood vessel lumina, resulting in an increase in serum potassium. The purpose of the present study was to assess whether this potassium release is due to hemolysis. Fresh human blood was mixed in vitro with CM at a ratio of 10:2. Potassium release rates were determined, and serum haptoglobin and free hemoglobin were measured after 30 min of exposure to CM. To compare the potassium release curve between CM exposure and true hemolysis induced by distilled water, fresh human blood was also mixed with distilled water. The level of serum haptoglobin decreased due to hemodilution. Changes in haptoglobin were not correlated with potassium release rates. The serum free hemoglobin level did not increase significantly, and there was no correlation between changes in the free hemoglobin level and the rate of potassium release. Hemolysis caused by water occurred instantaneously, whereas potassium release caused by CM was a slow response, which was linearly correlated with exposure time. Potassium release from blood cannot be explained by hemolysis. (orig.) With 4 figs., 4 tabs., 3 refs.

How to (really) reduce the greenhouse gases releases

International Nuclear Information System (INIS)

Masurel, J.; Frot, J.

2009-01-01

Based on the last 2008 GIEC report, 'Sauvons le Climat' presupposes the character essentially anthropic of the climatic change and concludes to the requirement to divide by four, between now and 2050, the releases of greenhouse gases of the OECD countries. The world energetic balance is composed, for 80% of carbonaceous energies: petroleum, coal and natural gas. At the world-wide level, the preoccupations of the energetic resources and those of climate protection go therefore hand in hand. It is the same thing for the European Union but not for France whose carbonaceous energies part is only of 50%. That is to say, in France, an energy savings has only one chance of two to improve its energetic independence and to protect the climate. Especially for France, 'Sauvons le Climat' gives then here some advices to really reduce the greenhouse gases releases. (O.M.)

Applied exposure modeling for residual radioactivity and release criteria

International Nuclear Information System (INIS)

Lee, D.W.

1989-01-01

The protection of public health and the environment from the release of materials with residual radioactivity for recycle or disposal as wastes without radioactive contents of concern presents a formidable challenge. Existing regulatory criteria are based on technical judgment concerning detectability and simple modeling. Recently, exposure modeling methodologies have been developed to provide a more consistent level of health protection. Release criteria derived from the application of exposure modeling methodologies share the same basic elements of analysis but are developed to serve a variety of purposes. Models for the support of regulations for all applications rely on conservative interpretations of generalized conditions while models developed to show compliance incorporate specific conditions not likely to be duplicated at other sites. Research models represent yet another type of modeling which strives to simulate the actual behavior of released material. In spite of these differing purposes, exposure modeling permits the application of sound and reasoned principles of radiation protection to the release of materials with residual levels of radioactivity. Examples of the similarities and differences of these models are presented and an application to the disposal of materials with residual levels of uranium contamination is discussed. 5 refs., 2 tabs

Estimate of radionuclide release characteristics into containment under severe accident conditions

International Nuclear Information System (INIS)

Nourbakhsh, H.P.

1993-11-01

A detailed review of the available light water reactor source term information is presented as a technical basis for development of updated source terms into the containment under severe accident conditions. Simplified estimates of radionuclide release and transport characteristics are specified for each unique combination of the reactor coolant and containment system combinations. A quantitative uncertainty analysis in the release to the containment using NUREG-1150 methodology is also presented

Measurements of the Shock Release Of Quartz and Paralyene-N

Science.gov (United States)

Hawreliak, James; Karasik, Max; Oh, Jaechul; Aglitskiy, Yefim

2017-06-01

The shock and release properties of Quartz and hydrocarbons are important to high energy density (HED) research and inertial confinement fusion (ICF) science. The bulk of HED material research studies single shock or multiple shock conditions. The challenge with measuring release properties is unlike shocks which have a single interface from which to measure the properties, the release establishes gradients in the sample. The streaked x-ray imaging capability of the NIKE laser allow the interface between quartz and CH to be measured during the release, giving measurements of the interface velocity and CH density. Here, we present experimental results from the NIKE laser where quartz and parylene-N are shock compressed to high pressure and temperature and the release state is measured through x-ray imaging. The shock state is characterized by shock front velocity measurements using VISAR and the release state is characterized by using side-on streaked x-ray radiography Work supported by DOE/NNSA.

Present Status of the JENDL Project (May, 2014)

International Nuclear Information System (INIS)

Iwamoto, Osamu; Yokoyama, Kenji

2014-01-01

The Japanese Nuclear Data Committee (JNDC) is a research committee for JAEA research activities. It has two subcommittees: Subcommittee on Nuclear Data and Subcommittee on Reactor Constants. The JENDL-4.0 Updated Files (JENDL-4.0u) have been produced to take care of errors which were found after the release of JENDL-4.0. The JENDL-4.0u includes the nuclides whose nuclear data partly revised from important and/or trivial error(s). Thirteen files for JENDL-4.0 were released in 2013. Benchmarking for fission reactor applications was done using test files of Gd-157 and Am-241, and an integral testing for Th-232 was done using KUCA critical experiments. The data which are not updated in JENDL-4.0 are continuously considered to be revised, especially for FP region nuclides. Evaluated results for 141,143 Pr, 121,123-126 Sb and 96,98-106 Ru were published. The R-matrix analysis for O-16 is in progress. For decommissioning of nuclear power plants, evaluation of activation cross sections was planned for 569 reactions with 309 nuclides and is in progress. Evaluated files for the 246 isotopes from H to Hf have been created. As the activity of High Energy Nuclear Data Evaluation WG, development of new JENDL Photonuclear Data File is in progress. Evaluation for 181 nuclides has been finished. A Symposium on Nuclear Data was held on 14-15 November 2013 at Research Institute of Nuclear Engineering, University of Fukui, Tsuruga-shi, with topics about Progress in neutron cross-section measurement and analysis, Application of Nuclear Data, Recent topics, and Progress in studies of high-energy nuclear reaction. A total of 37 papers including 23 poster presentations were presented

Design and characterization of controlled release tablet of metoprolol

Directory of Open Access Journals (Sweden)

Gautam Singhvi

2012-01-01

Full Text Available Metoprolol succinate is a selective beta-adrenergic receptor blocker useful in treatment of hypertension, angina and heart failure. The purpose of the present work was to design and evaluate controlled release matrix type tablet of Metoprolo succinate using HPMC K15M and Eudragit (RLPO and RSPO as a matrix forming agents. Effect of various polymer alone and combinations were studied in pH 1.2 buffer using USP type II paddle at 50 rpm. HPMC was used to form firm gel with Eudragit polymer. Formulation with Equal proportion (1:1 of Eudragit RSPO and RLPO showed optimum drug release t50 =7 hrs and t100 =16 hrs indicate optimum permeability for drug release from matrix. The drug release mechanism was predominantly found to be Non-Fickian diffusion controlled.

Fission product release from fuel of water-cooled reactors

International Nuclear Information System (INIS)

Strupczewski, A.; Marks, P.; Klisinska, M.

1997-01-01

The report contains a review of theoretical models and experimental works of gaseous and volatile fission products from uranium dioxide fuel. The experimental results of activity release at low burnup and the model of fission gas behaviour at initial stage of fuel operational cycle are presented. Empirical models as well as measured results of transient fission products release rate in the temperature up to UO 2 melting point, with consideration of their chemical reactions with fuel and cladding, are collected. The theoretical and experimental data were used for calculations of gaseous and volatile fission products release, especially iodine and caesium, to the gas volume of WWER-1000 and WWER-440 type fuel rods at low and high burnup and their further release from defected rods at the assumed loss-of-coolant accident. (author)

Hydrogen Release From 800-MeV Proton-Irradiated Tungsten

International Nuclear Information System (INIS)

Oliver, Brian M.; Venhaus, Thomas J.; Causey, Rion A.; Garner, Francis A.; Maloy, Stuart A.

2002-01-01

Tungsten irradiated in spallation neutron sources such as those proposed for the Accelerator Production of Tritium (APT) project, or in proposed fusion reactors, will contain large quantities of generated helium and hydrogen gas. In the APT, spallation neutrons would be generated by the interaction of high energy (∼1 GeV) protons with solid tungsten rods or cylinders. In fusion reactors, tungsten used in a tokamak diverter will contain hydrogen, as well as deuterium and tritium diffusing in from the plasma-facing surface. The release kinetics of these gases during various off-normal scenarios involving loss of coolant and afterheat-induced rises in temperature is of particular interest for both applications. To determine the release kinetics of hydrogen from tungsten, tungsten rods irradiated with 800 MeV protons in the Los Alamos Neutron Science Center (LANCE) to high exposures as part of the APT project have been examined. Hydrogen evolution from the tungsten was measured using a dedicated mass spectrometer system by subjecting the specimens to an essentially linear temperature ramp from ∼323 K to ∼1473 K. Release profiles are compared with predictions obtained using the Tritium Migration Analysis Program (TMAP4). Input parameters for the modeling, consisting of diffusivity, recombination rate coefficient, and trapping, are discussed. The measurements show that for high proton doses, the majority of the hydrogen is released gradually, starting at about 900 K and reaching a maximum at about 1400 K, where it drops fairly rapidly. Comparisons with TMAP show reasonable agreement at high proton dose using a trap value of 1.4 eV and a trap density of 3%. There is also a small release fraction occurring at ∼600 K which predominates at lower proton doses, and which is relatively independent of dose. This lower-temperature release is predicted by TMAP if no traps are assumed, suggesting that this release may represent an adsorbed surface component

32 CFR Appendix B to Part 45 - DD Form 214ws

Science.gov (United States)

2010-07-01

... 32 National Defense 1 2010-07-01 2010-07-01 false DD Form 214ws B Appendix B to Part 45 National... CERTIFICATE OF RELEASE OR DISCHARGE FROM ACTIVE DUTY (DD FORM 214/5 SERIES) Pt. 45, App. B Appendix B to Part 45—DD Form 214ws EC23OC91.007 ...

Development and evaluation of accelerated drug release testing methods for a matrix-type intravaginal ring.

Science.gov (United States)

Externbrink, Anna; Eggenreich, Karin; Eder, Simone; Mohr, Stefan; Nickisch, Klaus; Klein, Sandra

2017-01-01

Accelerated drug release testing is a valuable quality control tool for long-acting non-oral extended release formulations. Currently, several intravaginal ring candidates designed for the long-term delivery of steroids or anti-infective drugs are being in the developing pipeline. The present article addresses the demand for accelerated drug release methods for these formulations. We describe the development and evaluation of accelerated release methods for a steroid releasing matrix-type intravaginal ring. The drug release properties of the formulation were evaluated under real-time and accelerated test conditions. Under real-time test conditions drug release from the intravaginal ring was strongly affected by the steroid solubility in the release medium. Under sufficient sink conditions that were provided in release media containing surfactants drug release was Fickian diffusion driven. Both temperature and hydro-organic dissolution media were successfully employed to accelerate drug release from the formulation. Drug release could be further increased by combining the temperature effect with the application of a hydro-organic release medium. The formulation continued to exhibit a diffusion controlled release kinetic under the investigated accelerated conditions. Moreover, the accelerated methods were able to differentiate between different prototypes of the intravaginal ring that exhibited different release profiles under real-time test conditions. Overall, the results of the present study indicate that both temperature and hydro-organic release media are valid parameters for accelerating drug release from the intravaginal ring. Variation of either a single or both parameters yielded release profiles that correlated well with real-time release. Copyright © 2016 Elsevier B.V. All rights reserved.

Tuning silver ion release properties in reactively sputtered Ag/TiOx nanocomposites

Science.gov (United States)

Xiong, J.; Ghori, M. Z.; Henkel, B.; Strunskus, T.; Schürmann, U.; Deng, M.; Kienle, L.; Faupel, F.

2017-07-01

Silver/titania nanocomposites with strong bactericidal effects and good biocompatibility/environmental safety show a high potential for antibacterial applications. Tailoring the silver ion release is thus highly promising to optimize the antibacterial properties of such coatings and to preserve biocompatibility. Reactive sputtering is a fast and versatile method for the preparation of such Ag/TiOx nanocomposites coatings. The present work is concerned with the influence of sputter parameters on the surface morphology and silver ion release properties of reactively sputtered Ag/TiOx nanocomposites coatings showing a silver nanoparticle size distribution in the range from 1 to 20 nm. It is shown that the silver ion release rate strongly depends on the total pressure: the coatings prepared at lower pressure present a lower but long-lasting release behavior. The much denser structure produced under these conditions reduces the transport of water molecules into the coating. In addition, the influence of microstructure and thickness of titanium oxide barriers on the silver ion release were investigated intensively. Moreover, for the coatings prepared at high total pressure, it was demonstrated that stable and long-lasting silver release can be achieved by depositing a barrier with a high rate. Nanocomposites produced under these conditions show well controllable silver ion release properties for applications as antibacterial coatings.

Selected Papers and Presentations Presented at MODSIM World 2010 Conference and Expo. Part 1

Science.gov (United States)

Pinelli, Thomas E. (Editor)

2011-01-01

MODSIM World 2010 was held in Hampton, Virginia, October 13-15, 2010. The theme of the 2010 conference & expo was "21st Century Decision-Making: The Art of Modeling& Simulation". The conference program consisted of seven technical tracks - Defense, Engineering and Science, Health & Medicine, Homeland Security & First Responders, The Human Dimension, K-20 STEM Education, and Serious Games & Virtual Worlds. Selected papers and presentations from MODSIM World 2010 Conference & Expo are contained in this NASA Conference Publication (CP). Section 8.0 of this CP contains papers from MODSIM World 2009 Conference & Expo that were unavailable at the time of publication of NASA/CP-2010-216205 Selected Papers Presented at MODSIM World 2009 Conference and Expo, March 2010.

The influence of season of the year on the predicted agricultural consequences of accidental releases of radionuclides to atmosphere

International Nuclear Information System (INIS)

Simmonds, J.R.

1985-02-01

In Europe, because of the seasonal nature of agricultural practices, the consequences for agriculture of an accidental release of radioactive materials to atmosphere are likely to vary depending upon the time of year when the release occurs. The quantification of this variation is complicated by the need to take into account the introduction of countermeasures to restrict the radiation exposure from ingestion of contaminated foods, and by the presence in accidental releases of radionuclides which persist over several seasons. In this study, the effect on agricultural consequences of accidental releases occurring at different times of the year is examined. The consequences are expressed in terms of the amount of produce affected by restrictions on food supplies and the collective radiation dose from ingestion of food. The investigation has been carried out for three hypothetical releases representing a range of releases postulated for pressurised water reactors (PWRs). The effect of season of the year was determined for accidental releases occurring both in a single, defined set of meteorological conditions and for a range of possible meteorological conditions. For the main part of the study, consideration was limited to agricultural production in the UK only, but the effect of extending the analysis beyond the UK boundary was also considered. The results of the study show that considerable variation can occur in agricultural consequences following an accidental release at different times of the year. For the larger releases considered, this variation is reduced due to the effect of the introduction of countermeasures, particularly when consideration is limited to the UK only. Seasonal variation tends to be greater for the results of a deterministic analysis, which uses a single set of constant meteorological conditions, than for the results of a full probabilistic assessment. From the results presented here it is also seen that for many applications of

Transfer of tritium released by nuclear facilities to the food supply

International Nuclear Information System (INIS)

Bovard, P.; Delmas, J.; Belot, Y.; Camus, H.; Grauby, A.; Hoek, J. van den

1979-01-01

The use for agricultural purposes of river waters receiving releases or discharges of tritium results in contamination of irrigated crops and of animals given such water to drink or consuming the contaminated crops. It therefore seemed of importance to assess the part played by tritium in the contamination of the food chain, together with its possible effects on organisms. With this in mind, French, Belgian and Netherlands laboratories have joined forces to study, more especially, the relationship between environmental contamination rates and those of produce harvested in the Mediterranean region and in a humid temperate climate, the transfer process in the chain: water - fodder - bovines - dairy produce, and the role of technology in the contamination of the food chain. The present status of research undertaken jointly by organizations in the three countries is reviewed. In the Atlantic environment the experiments involved four annual crops consumed on a large scale: potatoes, sugar beet, carrots and peas, and in the Mediterranean environment several perennial species such as vine, olive, orange and apple were studied. The results obtained relate to the residence time for tritium in the various organs of each species, the part played by evapotranspiration and the physiological functions of the different parts of the plants, the uptake of tritium by tissue water and organic matter, and the distribution of tritium in the soil profile. (author)

Competitive release and facilitation of drug-resistant parasites after therapeutic chemotherapy in a rodent malaria model

Science.gov (United States)

Wargo, A.R.; Huijben, S.; De Roode, J. C.; Shepherd, J.; Read, A.F.

2007-01-01

Malaria infections frequently consist of mixtures of drug-resistant and drug-sensitive parasites. If crowding occurs, where clonal population densities are suppressed by the presence of coinfecting clones, removal of susceptible clones by drug treatment could allow resistant clones to expand into the newly vacated niche space within a host. Theoretical models show that, if such competitive release occurs, it can be a potent contributor to the strength of selection, greatly accelerating the rate at which resistance spreads in a population. A variety of correlational field data suggest that competitive release could occur in human malaria populations, but direct evidence cannot be ethically obtained from human infections. Here we show competitive release after pyrimethamine curative chemotherapy of acute infections of the rodent malaria Plasmodium chabaudi in laboratory mice. The expansion of resistant parasite numbers after treatment resulted in enhanced transmission-stage densities. After the elimination or near-elimination of sensitive parasites, the number of resistant parasites increased beyond that achieved when a competitor had never been present. Thus, a substantial competitive release occurred, markedly elevating the fitness advantages of drug resistance above those arising from survival alone. This finding may explain the rapid spread of drug resistance and the subsequently brief useful lifespans of some antimalarial drugs. In a second experiment, where subcurative chemotherapy was administered, the resistant clone was only partly released from competitive suppression and experienced a restriction in the size of its expansion after treatment. This finding raises the prospect of harnessing in-host ecology to slow the spread of drug resistance. ?? 2007 by The National Academy of Sciences of the USA.

Mediastinoscopic Bilateral Bronchial Release for Long Segmental Resection and Anastomosis of the Trachea

OpenAIRE

Kang, Jeong-Han; Park, In Kyu; Bae, Mi-Kyung; Hwang, Yoohwa

2011-01-01

The extent of resection and release of the trachea is important for successful anastomosis. Bilateral bronchial dissection is one of the release techniques for resection of the lower trachea. We present the experience of cervical video-assisted mediastinoscopic bilateral bronchial release for long segmental resection and anastomosis of the lower trachea.

TOXRISK, Toxic Gas Release Accident Analysis

International Nuclear Information System (INIS)

Bennett, D.E.; Chanin, D.I.; Shiver, A.W.

1993-01-01

1 - Description of program or function: TOXRISK is an interactive program developed to aid in the evaluation of nuclear power plant control room habitability in the event of a nearby toxic material release. The program uses a model which is consistent with the approach described in the NRC Regulatory Guide 1.78. Release of the gas is treated as an initial puff followed by a continuous plume. The relative proportions of these as well as the plume release rate are supplied by the user. Transport of the gas is modeled as a Gaussian distribution and occurs through the action of a constant velocity, constant direction wind. Great flexibility is afforded the user in specifying the release description, meteorological conditions, relative geometry of the accident and plant, and the plant ventilation system characteristics. Two types of simulation can be performed: multiple case (parametric) studies and probabilistic analyses. Upon execution, TOXRISK presents a menu, and the user chooses between the Data Base Manager, the Multiple Case program, and the Probabilistic Study Program. The Data Base Manager provides a convenient means of storing, retrieving, and modifying blocks of data required by the analysis programs. The Multiple Case program calculates resultant gas concentrations inside the control room and presents a summary of information that describes the event for each set of conditions given. Optimally, a time history profile of inside and outside concentrations can also be produced. The Probabilistic Study program provides a means for estimating the annual probability of operator incapacitation due to toxic gas accidents on surrounding transportation routes and storage sites. 2 - Method of solution: Dispersion or diffusion of the gas during transport is described by modified Pasquill-Gifford dispersion coefficients

Analysis of hydrogen sulfide releases in heavy water production facilities

International Nuclear Information System (INIS)

Croitoru, Cornelia; Dumitrescu, Maria; Preda, Irina; Lazar, Roxana

1996-01-01

Safety analyses conducted at ICIS concern primarily the heavy water production installations. The quantitative risk assessment needs the frequency calculation of accident sequences and consequences. In heavy water plants which obtain primary isotopic concentration of water by H 2 O - H 2 S exchange, large amounts of hydrogen sulfide which is a toxic, inflammable and explosive gas, are circulated. The first stage in calculating the consequences consists in potential analysis of H 2 S release. This work presents a study of this types of releases for pilot installations of the heavy water production at ICIS (Plant 'G' at Rm. Valcea). The installations which contain and maneuver large quantities of H 2 S and the mathematical models for different types of releases are presented. The accidents analyzed are: catastrophic column, container, spy-hole failures or gas-duct rupture and wall cracks in the installation. The main results are given as tables while the time variations of the flow rate and quantities of H 2 O released by stack disposal are plotted

The gamma spectrometry a powerful tool for irradiated fuel and fission products release studies

International Nuclear Information System (INIS)

Pontillon, Y.; Roure, C.; Lacroix, B.; Martella, T.; Ducros, G.; Ravel, S.; Gleizes, B.

2003-01-01

Over the last decades, due to the potentially severe consequences of a nuclear incident and/or accident for surrounding populations as well as the environment, international safety authorities launched R and D programs in support of general policy on exploitation of nuclear energy. This increasing interest enabled starting of many research programs in CEA and particularly in Nuclear Energy Directorate (DEN). Most of them are devoted to (i) the source term of fission products (including gas) and actinides released from PWR fuel samples in normal or accident conditions, (ii) burn-up determination, (iii) isotopic repartition... by quantitative gamma spectrometry. In this context, the Department of Fuel Studies (DEC), part of the DEN, has acquired considerable experience in this field of research. In order to attain the required capabilities, specific technical facilities set up in shielded hot cells at the CEA-Grenoble and CEA-Cadarache have been developed. In particular, the researchers of the Department have developed several gamma scanning benches and a set of two thermal treatment devices, including the so-called 'VERCORS facility'. These devices are associated to on line quantitative gamma spectrometry, in order to measure emitted gas and fission products (FPs). The greatest asset of such installations is to ensure a high analytical experiments rate, and as a consequence to make parametrical approach of planned studies easier. The first part of the present communication focuses, on the one hand, on the peculiar aspects of the gamma spectrometry applied on irradiated fuel, mad on the other hand, on the technical aspect of the different facilities (i.e. quantitative gamma spectrometry apparatus and corresponding 'home made' software). The last part is devoted to the results which can be obtained with such installation. In particular, it will be explained how experimental programs on FPs and gas release in normal and/or accidental conditions can be conducted

Officially released mutant varieties - the FAO/IAEA Database

International Nuclear Information System (INIS)

Maluszynski, M.; Nichterlein, K.; Zanten, L. van; Ahloowalia, B.S.

2000-01-01

In the approximately 70 year-old history of induced mutations, there are many examples on the development of new and valuable alteration in plant characters significantly contributing to increased yield potential of specific crops. However, knowledge on the success of induced mutations in crop improvement among geneticists and breeders is usually limited to species of their interest. The present paper contains a comprehensive list of officially released mutant varieties, based on information from plant breeders. The number of mutant varieties officially released and recorded in the FAO/IAEA Mutant Varieties Database before the end of 2000 is 2,252. Almost half of these varieties have been released during the last 15 years. Considering a significant delay in the dissemination of information on newly released varieties and difficulties in the collection of such data, there has been a renaissance in the use of mutation techniques in crop improvement. At the demand of geneticists, plant breeders, and more recently molecular geneticists, for information on released mutant varieties of specific crops, the MVD was transferred to the web site of the FAO/IAEA Joint Division. The MVD will be available on our web pages early in 2001. (author)

Estimation of cobalt release from feed water heater tubes of BWRs

International Nuclear Information System (INIS)

Uchida, S.; Kitamura, M.; Ozawa, Y.

1983-01-01

To evaluate the release source of cobalt from heater tubes of the feed water line, release rate measurements were carried out by detecting 60 Co released from irradiated stainless steel in contact with neutral water at an oxygen concentration of 20 ppb. The dependences of cobalt release rate on temperature, flow velocity and exposure time were studied after 670 hours of release experiments, and an empirical equation (which is presented) was obtained in the temperature range from 150 to 240 deg C. A decrease in the cobalt release rate above 250 deg C was considered due to the formation of a protective oxide layer. From these data, the amount of cobalt released from individual feed water heaters was evaluated. It was demonstrated that low cobalt containing stainless steel was economically applied only in the higher temperature region of the heater (20% of the total surface) to reduce cobalt feed rate into the reactor (to approx. 1/2). (author)

Development of modified-release tablets of zolpidem tartrate by biphasic quick/slow delivery system.

Science.gov (United States)

Mahapatra, Anjan Kumar; Sameeraja, N H; Murthy, P N

2015-06-01

Zolpidem tartrate is a non-benzodiazepine analogue of imidazopyridine of sedative and hypnotic category. It has a short half-life with usual dosage regimen being 5 mg, two times a day, or 10 mg, once daily. The duration of action is considered too short in certain circumstances. Thus, it is desirable to lengthen the duration of action. The formulation design was implemented by preparing extended-release tablets of zolpidem tartrate using the biphasic delivery system technology, where sodium starch glycolate acts as a superdisintegrant in immediate-release part and hydroxypropyl methyl cellulose as a release retarding agent in extended-release core. Tablets were prepared by direct compression. Both the core and the coat contained the drug. The pre-compression blends were evaluated for angle of repose, bulk density, and compressibility index. The tablets were evaluated for thickness, hardness, weight variation test, friability, and in vitro release studies. No interaction was observed between zolpidem tartrate and excipients from the Fourier transform infrared spectroscopy and differential scanning calorimetry analysis. The results of all the formulations prepared were compared with reference product Stilnoct®. Optimized formulations showed release patterns that match the United States Pharmacopeia (USP) guidelines for zolpidem tartrate extended-release tablets. The mechanism of drug release was studied using different mathematical models, and the optimized formulation has shown Fickian diffusion. Accelerated stability studies were performed on the optimized formulation.

Analysis of metal ion release from biomedical implants

Directory of Open Access Journals (Sweden)

Ivana Dimić

2013-06-01

Full Text Available Metallic biomaterials are commonly used for fixation or replacement of damaged bones in the human body due to their good combination of mechanical properties. The disadvantage of metals as implant materials is their susceptibility to corrosion and metal ion release, which can cause serious health problems. In certain concentrations metals and metal ions are toxic and their presence can cause diverse inflammatory reactions, genetic mutations or even cancer. In this paper, different approaches to metal ion release examination, from biometallic materials sample preparation to research results interpretation, will be presented. An overview of the analytical techniques, used for determination of the type and concentration of released ions from implants in simulated biofluids, is also given in the paper.

Transport in biosphere of radionuclides released from finally disposed nuclear waste - background information for transport and dose model

International Nuclear Information System (INIS)

Hulmi, R.; Savolainen, I.

1981-07-01

An outline is made about the biosphere transport and dose models employed in the estimation of doses due to releases from finally disposed nuclear waste. The models often divide into two parts; the first one describes the transport of radionuclides in those parts of biosphere where the time scale is large (e.g. soil, sea and sea sediment), the second part of the model describes the transport of nuclides in the systems where the time scale is small (e.g. food chains, plants and animals). The description of biosphere conditions includes remarkable uncertainty due to the complexity of the biosphere and its ecosystems. Therefore studies of scenario type are recommended: some values of parametres describing the conditions are assumed, and the consequences are estimated by using these values. The effect of uncertainty in various factors on the uncertainty of final results should be investigated with the employment of alternative scenarios and parametric sensitivity studies. In addition to the ordinary results, intermediate results should be presented. A proposal for the structure of a transport and dose program based on dynamic linear compartment model is presented and mathematical solution alternatives are studied also

Seminar on Comparative assessment of the environmental impact of radionuclides released during three major nuclear accidents: Kyshtym, Windscale, Chernobyl. Vol. 1

International Nuclear Information System (INIS)

1991-01-01

These proceedings of seminar on comparative assessment of the environmental impact of radionuclides released during three major nuclear accidents (Kyshtym, Windscale, Chernobyl) are divided into 5 parts bearing on: part 1: accident source terms; part 2: atmospheric dispersion, resuspension, chemical and physical forms of contamination; part 3: environmental contamination and transfer; part 4: radiological implications for man and his environment; part 5: countermeasures

Methodology for assessing the radiological consequences of radioactive releases from the BPX Facility at PPPL

International Nuclear Information System (INIS)

McKenzie-Carter, M.A.; Lyon, R.E.; Rope, S.K.

1991-04-01

This report contains information to support the Environmental Assessment for the Burning Plasma Experiment (BPX) Project proposed for the Princeton Plasma Physics Laboratory (PPPL). The assumptions and methodology used to assess the impact to members of the public from operational and accidental releases of radioactive material from the proposed BPX during the operational period of the project are described. A description of the tracer release tests conducted at PPPL by NOAA is included; dispersion values from these tests are used in the dose calculations. Radiological releases, doses, and resulting health risks are calculated and summarized. The computer code AIRDOS- EPA, which is part of the computer code system CAP-88, is used to calculate the individual and population doses for routine releases; FUSCRAC3 is used to calculate doses resulting from off-normal releases where direct application of the NOAA tracer test data is not practical. Where applicable, doses are compared to regulatory limits and guideline values. 48 refs., 16 tabs

Interactions of MK-801 with glutamate-, glutamine- and methamphetamine-evoked release of [3H]dopamine from striatal slices

International Nuclear Information System (INIS)

Bowyer, J.F.; Scallet, A.C.; Holson, R.R.; Lipe, G.W.; Slikker, W. Jr.; Ali, S.F.

1991-01-01

The interactions of MK-801 [(+)-5-methyl-10,11-dihydro-5H-dibenzo[a,d] cyclohepten-5,10-imine], glutamate and glutamine with methamphetamine (METH)-evoked release of [ 3 H]dopamine were assessed in vitro to determine whether MK-801 inhibition of METH neurotoxicity might be mediated presynaptically, and to evaluate the effects of glutamatergic stimulation on METH-evoked dopamine release. MK-801 inhibition of glutamate- or METH-evoked dopamine release might reduce synaptic dopamine levels during METH exposure and decrease the formation of 6-hydroxydopamine or other related neurotoxins. Without Mg 2+ present, 40 microM and 1 mM glutamate evoked a N-methyl-D-aspartate receptor-mediated [ 3 H]dopamine and [ 3 H]metabolite (tritium) release of 3 to 6 and 12 to 16% of total tritium stores, respectively, from striatal slices. With 1.50 mM Mg 2+ present, 10 mM glutamate alone or in combination with the dopamine uptake blocker nomifensine released only 2.1 or 4.2%, respectively, of total tritium stores, and release was only partially dependent on N-methyl-D-aspartate-type glutamate receptors. With or without 1.50 mM Mg 2+ present, 0.5 or 5 microM METH evoked a substantial release of tritium (5-8 or 12-21% of total stores, respectively). METH-evoked dopamine release was not affected by 5 microM MK-801 but METH-evoked release was additive with glutamate-evoked release. Without Mg 2+ present, 1 mM glutamine increased glutamate release and induced the release of [ 3 H]dopamine and metabolites. Both 0.5 and 5 microM METH also increased tritium release with 1 mM glutamine present. When striatal slices were exposed to 5 microM METH this glutamine-evoked release of glutamate was increased more than 50%

Arrested motherhood : Parenting, cognitive distortions, and depressive symptoms in mothers being released from incarceration

NARCIS (Netherlands)

Menting, A.T.A.; Orobio De Castro, B.; Matthys, W.C.H.J.

2017-01-01

Objective. The present study examines cognitive and emotional problems in mothers being released from incarceration. Design. Participants were 98 mothers who were about to be released or had just been released from incarceration, and 63 comparison mothers from disadvantaged areas with low

Results of dose calculations for NET accidental and normal operation releases of tritium and activation products

International Nuclear Information System (INIS)

Raskob, W.; Hasemann, I.

1992-08-01

This report documents conditions, data and results of dose calculations for accidental and normal operation releases of tritium and activation products, performed within the NET subtask SEP2.2 ('NET-Benchmark') of the European Fusion Technology Programme. For accidental releases, the computer codes UFOTRI and COSYMA for assessing the radiological consequences, have been applied for both deterministic and probabilistic calculations. The influence on dose estimates of different release times (2 minutes / 1 hour), two release heights (10 m / 150 m), two chemical forms of tritium (HT/HTO), and two different model approaches for the deposition velocity of HTO on soil was investigated. The dose calculations for normal operation effluents were performed using the tritium model of the German regulatory guidelines, parts of the advanced dose assessment model NORMTRI still under development, and the statistical atmospheric dispersion model ISOLA. Accidental and normal operation source terms were defined as follows: 10g (3.7 10 15 Bq) for accidental tritium releases, 10 Ci/day (3.7 10 11 Bq/day) for tritium releases during normal operation and unit releases of 10 9 Bq for accidental releases of activation products and fission products. (orig./HP) [de

Australian radiation therapy – Part two: Reflections of the past, the present, the future

Energy Technology Data Exchange (ETDEWEB)

Merchant, Susan [Radiation Oncology Department, Royal Adelaide Hospital, Adelaide, SA (Australia); Curtin Health Innovative Research Institute, Curtin University, Perth, WA (Australia); Halkett, Georgia [Curtin Health Innovative Research Institute, Curtin University, Perth, WA (Australia); Sale, Charlotte [Radiation Oncology, Andrew Love Cancer Centre, Barwon Health, Geelong, Vic. (Australia); Radiation Oncology Department, Royal Adelaide Hospital, Adelaide, SA (Australia); Collaboration: Grad Cert Grief & Pall Care Counselling, MIR

2014-02-15

Introduction: Documentation on the history of Australian radiotherapy is limited. This study provides radiation therapists' (RTs) perspectives of the people, workplace, and work practices in Australian radiotherapy centres from 1960 onwards. It provides a follow-up to our previous study: Australian radiation therapy: An overview – Part one, which outlines the history and development of radiotherapy from conception until present day. Methods: Four focus groups were conducted on separate occasions in 2010, one in South Australia and three in Victoria, Australia. Participants who worked in radiotherapy were purposively selected to ensure a range of experience, age, and years of work. Results: From a RT perspective, radiotherapy has evolved from a physically demanding ‘hands-on’ work environment, often with unpleasant sights and smells of disease, to a more technology-driven workplace. Conclusion: Understanding these changes and their subsequent effects on the role of Australian RTs will assist future directions in advanced role development.

Australian radiation therapy – Part two: Reflections of the past, the present, the future

International Nuclear Information System (INIS)

Merchant, Susan; Halkett, Georgia; Sale, Charlotte

2014-01-01

Introduction: Documentation on the history of Australian radiotherapy is limited. This study provides radiation therapists' (RTs) perspectives of the people, workplace, and work practices in Australian radiotherapy centres from 1960 onwards. It provides a follow-up to our previous study: Australian radiation therapy: An overview – Part one, which outlines the history and development of radiotherapy from conception until present day. Methods: Four focus groups were conducted on separate occasions in 2010, one in South Australia and three in Victoria, Australia. Participants who worked in radiotherapy were purposively selected to ensure a range of experience, age, and years of work. Results: From a RT perspective, radiotherapy has evolved from a physically demanding ‘hands-on’ work environment, often with unpleasant sights and smells of disease, to a more technology-driven workplace. Conclusion: Understanding these changes and their subsequent effects on the role of Australian RTs will assist future directions in advanced role development

Assessment of CPA Candidates' Education: Part Two

Science.gov (United States)

Giffin, Richard B.; Geddie, Mary; Moser, Ernest; Griffin, B. Wynne

2012-01-01

This paper is the second of a two part study comparing The Sixth Edition of the Uniform Accountancy Act as prepared and adopted by the National Association of State Boards of Accountancy (NASBA)with the actual regulatory practice of the various jurisdictional boards of accountancy in place just prior to the release of the most recent NASBA…

Using mass-release of engineered insects to manage insecticide resistance

International Nuclear Information System (INIS)

Alphey, Nina; Coleman, Paul G.; Donnelly, Christl A.

2006-01-01

Transgenic crops expressing insecticidal toxins derived from Bacillus thuringiensis (Bt) are widely used to control insect pests. The benefits of such crops would be lost if resistance to the toxins spread to a significant proportion of the pest population. The main resistance management method, mandatory in the US, is the high-dose/refuge strategy, requiring nearby refuges of toxin-free crops, and the use of toxin doses sufficiently high to kill not only wild type insects but also insects heterozygous for a resistance allele, thereby rendering the resistance functionally recessive. We propose that mass-release of harmless toxin-sensitive insects could substantially delay or even reverse the spread of resistance. Mass-release of such insects is an integral part of RIDL, a genetics-based method of pest control related to the Sterile Insect Technique. We used a population genetic mathematical model to analyze the effects of releasing male insects homozygous for a female-specific dominant lethal genetic construct, and concluded that this RIDL strategy could form an effective component of a resistance management scheme for insecticidal plants and other toxins. (author)

Using mass-release of engineered insects to manage insecticide resistance

Energy Technology Data Exchange (ETDEWEB)

Alphey, Nina [University of Oxford (United Kingdom). Dept. of Zoology; Alphey, Luke [Oxitec Limited, Oxford (United Kingdom); Coleman, Paul G [London School of Hygiene and Tropical Medicine (United Kingdom). Dept. of Infectious and Tropical Diseases; Donnelly, Christl A [Imperial College Faculty of Medicine, London (United Kingdom). Dept. of Infectious Disease Epidemiology

2006-07-01

Transgenic crops expressing insecticidal toxins derived from Bacillus thuringiensis (Bt) are widely used to control insect pests. The benefits of such crops would be lost if resistance to the toxins spread to a significant proportion of the pest population. The main resistance management method, mandatory in the US, is the high-dose/refuge strategy, requiring nearby refuges of toxin-free crops, and the use of toxin doses sufficiently high to kill not only wild type insects but also insects heterozygous for a resistance allele, thereby rendering the resistance functionally recessive. We propose that mass-release of harmless toxin-sensitive insects could substantially delay or even reverse the spread of resistance. Mass-release of such insects is an integral part of RIDL, a genetics-based method of pest control related to the Sterile Insect Technique. We used a population genetic mathematical model to analyze the effects of releasing male insects homozygous for a female-specific dominant lethal genetic construct, and concluded that this RIDL strategy could form an effective component of a resistance management scheme for insecticidal plants and other toxins. (author)

Sustained release nimesulide microparticles: evaluation of release modifying property of ethy

International Nuclear Information System (INIS)

Khan, S.A.; Ahmed, M.; Nisar-ur-Rehman; Madni, A.U.; Aamir, M.N.; Murtaza, G.

2011-01-01

Microencapsulated controlled-release preparations of nimesulide were formulated. Microparticles were prepared by modified phase separation (non-solvent addition) technique using different ratios of ethylcellulose. The microparticles (M/sub 1/, M/sub 2/, and M/sub 3/) were yellow, free flowing and spherical in shape with the particle size varying from 93.62 +- 14.15 to 104.19 +- 18.15 mu m. The t/sub 60%/of nimesulide release from microparticles was found to be 3 +- 0.6, 5 +- 0.6 and 8 +- 0.8 h for formulations M/sub 1/, M/sub 2/, and M/sub 3/, respectively. FT-IR, XRD, and thermal analysis were done which showed that there is no interaction between the polymer and drug. The mechanism of drug release from nimesulide microparticles was studied by using Higuchi and Korsmeyer-Peppas models. The value of coefficient of determination (R/sup 2/) for M/sub 1/, M/sub 2/, and M/sub 3/ indicates anomalous and case-II transport release mechanism. The dissolution data of designed system verified its ability to maintain plasma concentration without the need of frequent dosing. The Nimesulide microparticles prolonged drug release for 12 hours or longer. Based on the results of release studies, M/sub 3/ was opted as a suitable microparticulate formulation allowing the controlled release of nimesulide over a prolonged period of time. Moreover, its encapsulation efficiency was also comparable to the other two formulations (M/sub 1/ and M/sub 2/). In conclusion, the influence of polymer concentration should be considered during formulation development. (author)

Summary of the presentations

International Nuclear Information System (INIS)

2002-01-01

This part summarizes the content of the six following presentations: 1. IAEA requirements/guidance for the decommissioning safety case (Mike Bell, IAEA); 2. Safety case in an EIA context (Patrick O'SULLIVAN, The Netherlands); 3. Plant configuration and the D and D licensing process (Eugenio GIL LOPEZ and Pedro CARBONERAS, Spain); 4. Accident assessment (Ivo TRIPPUTI, Italy; Ingmar LUND, Sweden); 5. Balancing radiological and industrial risk in the safety case (Pascal DEBOODT, Belgium); 6. The safety case for safe store and dormancy periods (Paul WOOLLAM, UK). Following the six presentations, the WPDD members discussed the safety case in an open discussion led by the Topical Session Chair, Frances Taylor. The discussion was wide-ranging, and topics varied from the standards that apply to releases to the environment during safe store, to decommissioning parallels with other major processing industries and facilities (such as oil rigs). Frances Taylor steered the discussion toward addressing the questions that the WPDD Core Group had proposed for the topical session. The Chair, the Rapporteur, and some members of the group sensed that the presentations had covered such an wide variety of issues, and that the content of the presentations themselves differed so greatly, that it would be difficult to distill a position paper from the information gathered, as had been the mandate from the Core Group. In addition, the meaning of the term 'Safety Case' differed greatly among participants in the topical session. Some took the term to mean the analysis and document that the implementor provides to the regulator, describing how operations will be performed safely. Others considered the term to mean the overall safety and risk conditions inherent in a nuclear facility during operations or decommissioning. With the differences in presentations and with the meaning of the terminology remaining unclear, the WPDD participants did not reach consensus conclusions on December 5, 2001

Antimicrobial beeswax coated polylactide films with silver control release capacity.

Science.gov (United States)

Martínez-Abad, Antonio; Lagarón, Jose Maria; Ocio, María Jose

2014-03-17

Although the application of silver based antimicrobial systems is a widespread technology, its implementation in areas such as food packaging is still challenging. The present paper describes the fabrication of poly(lactic acid) (PLA) coated with beeswax with controlled release properties for sustained antimicrobial performance. Release of silver ions from the polymers was monitored voltammetrically under various conditions (surface contact, immersion in various liquid media and at different pH values) throughout at least 7days. A higher release was noted with decreasing pH while surface release was much slower than the release when immersed in liquid medium. While uncoated films demonstrated a high burst release which in some instances implied surpassing some current migration restrictions (food), the addition of a beeswax layer allowed a sustained release of the antimicrobial compound. Increasing the thickness of the beeswax layer resulted in an increase in the water barrier properties of the films while reducing the relatively constant values of sustained release. Antimicrobial performance was correlated with the release of silver ions, indicating threshold concentrations for biocide action of films displayed a strong bactericidal effect against Salmonella enterica. The application of this functional barrier thus offers the possibility of tuning the release profiles of the films to suit a specific application and puts forth the possible suitability of these materials for food packaging or other migration sensitive applications. Copyright © 2013 Elsevier B.V. All rights reserved.

Drug Release and Skin Permeation from Lipid Liquid Crystalline Phases

Science.gov (United States)

Costa-Balogh, F. O.; Sparr, E.; Sousa, J. J. S.; Pais, A. A. C. C.

We have studied drug release and skin permeation from several different liquid crystalline lipid formulations that may be used to control the respective release rates. We have studied the release and permeation through human skin of a water-soluble and amphiphilic drug, propranolol hydrochloride, from several formulations prepared with monoolein and phytantriol as permeation enhancers and controlled release excipients. Diolein and cineol were added to selected formulations. We observed that viscosity decreases with drug load, wich is compatible with the occurrence of phase changes. Diolein stabilizes the bicontinuous cubic phases leading to an increase in viscosity and sustained release of the drug. The slowest release was found for the cubic phases with higher viscosity. Studies on skin permeation showed that these latter formulations also presented lower permeability than the less viscous monoolein lamellar phases. Formulations containing cineol originated higher permeability with higher enhancement ratios. Thus, the various formulations are adapted to different circumstances and delivery routes. While a slow release is usually desired for drug sustained delivery, the transdermal route may require a faster release. Lamellar phases, which are less viscous, are more adapted to transdermal applications. Thus, systems involving lamellar phases of monoolein and cineol are good candidates to be used as skin permeation enhancers for propranolol hydrochloride.

Exhaustive Exercise-induced Oxidative Stress Alteration of Erythrocyte Oxygen Release Capacity.

Science.gov (United States)

Xiong, Yanlian; Xiong, Yanlei; Wang, Yueming; Zhao, Yajin; Li, Yaojin; Ren, Yang; Wang, Ruofeng; Zhao, Mingzi; Hao, Yitong; Liu, Haibei; Wang, Xiang

2018-05-24

The aim of the present study is to explore the effect of exhaustive running exercise (ERE) in the oxygen release capacity of rat erythrocytes. Rats were divided into sedentary control (C), moderate running exercise (MRE) and exhaustive running exercise groups. The thermodynamics and kinetics properties of the erythrocyte oxygen release process of different groups were tested. We also determined the degree of band-3 oxidative and phosphorylation, anion transport activity and carbonic anhydrase isoform II(CAII) activity. Biochemical studies suggested that exhaustive running significantly increased oxidative injury parameters in TBARS and methaemoglobin levels. Furthermore, exhaustive running significantly decreased anion transport activity and carbonic anhydrase isoform II(CAII) activity. Thermodynamic analysis indicated that erythrocytes oxygen release ability also significantly increased due to elevated 2,3-DPG level after exhaustive running. Kinetic analysis indicated that exhaustive running resulted in significantly decreased T50 value. We presented evidence that exhaustive running remarkably impacted thermodynamics and kinetics properties of RBCs oxygen release. In addition, changes in 2,3-DPG levels and band-3 oxidation and phosphorylation could be the driving force for exhaustive running induced alterations in erythrocytes oxygen release thermodynamics and kinetics properties.

Hydrogen release from 800 MeV proton-irradiated tungsten

Science.gov (United States)

Oliver, B. M.; Venhaus, T. J.; Causey, R. A.; Garner, F. A.; Maloy, S. A.

2002-12-01

Tungsten irradiated in spallation neutron sources, such as those proposed for the accelerator production of tritium (APT) project, will contain large quantities of generated helium and hydrogen gas. Tungsten used in proposed fusion reactors will also be exposed to neutrons, and the generated protium will be accompanied by deuterium and tritium diffusing in from the plasma-facing surface. The release kinetics of these gases during various off-normal scenarios involving loss of coolant and after heat-induced rises in temperature are of particular interest for both applications. To determine the release kinetics of hydrogen from tungsten, tungsten rods irradiated with 800 MeV protons in the Los Alamos Neutron Science Center (LANSCE) to high exposures as part of the APT project have been examined. Hydrogen evolution from the tungsten has been measured using a dedicated mass-spectrometer system by subjecting the specimens to an essentially linear temperature ramp from ˜300 to ˜1500 K. Release profiles are compared with predictions obtained using the Tritium Migration Analysis Program (TMAP4). The measurements show that for high proton doses, the majority of the hydrogen is released gradually, starting at about 900 K and reaching a maximum at about 1400 K, where it drops fairly rapidly. Comparisons with TMAP show quite reasonable agreement using a trap energy of 1.4 eV and a trap density of ˜7%. There is a small additional release fraction occurring at ˜550 K, which is believed to be associated with low-energy trapping at or near the surface, and, therefore, was not included in the bulk TMAP model.

Hydrogen release from 800 MeV proton-irradiated tungsten

International Nuclear Information System (INIS)

Oliver, B.M.; Venhaus, T.J.; Causey, R.A.; Garner, F.A.; Maloy, S.A.

2002-01-01

Tungsten irradiated in spallation neutron sources, such as those proposed for the accelerator production of tritium (APT) project, will contain large quantities of generated helium and hydrogen gas. Tungsten used in proposed fusion reactors will also be exposed to neutrons, and the generated protium will be accompanied by deuterium and tritium diffusing in from the plasma-facing surface. The release kinetics of these gases during various off-normal scenarios involving loss of coolant and after heat-induced rises in temperature are of particular interest for both applications. To determine the release kinetics of hydrogen from tungsten, tungsten rods irradiated with 800 MeV protons in the Los Alamos Neutron Science Center (LANSCE) to high exposures as part of the APT project have been examined. Hydrogen evolution from the tungsten has been measured using a dedicated mass-spectrometer system by subjecting the specimens to an essentially linear temperature ramp from ∼300 to ∼1500 K. Release profiles are compared with predictions obtained using the Tritium Migration Analysis Program (TMAP4). The measurements show that for high proton doses, the majority of the hydrogen is released gradually, starting at about 900 K and reaching a maximum at about 1400 K, where it drops fairly rapidly. Comparisons with TMAP show quite reasonable agreement using a trap energy of 1.4 eV and a trap density of ∼7%. There is a small additional release fraction occurring at ∼550 K, which is believed to be associated with low-energy trapping at or near the surface, and, therefore, was not included in the bulk TMAP model

Hydrogen release from 800 MeV proton-irradiated tungsten

Energy Technology Data Exchange (ETDEWEB)

Oliver, B.M. E-mail: brian.oliver@pnl.gov; Venhaus, T.J.; Causey, R.A.; Garner, F.A.; Maloy, S.A

2002-12-01

Tungsten irradiated in spallation neutron sources, such as those proposed for the accelerator production of tritium (APT) project, will contain large quantities of generated helium and hydrogen gas. Tungsten used in proposed fusion reactors will also be exposed to neutrons, and the generated protium will be accompanied by deuterium and tritium diffusing in from the plasma-facing surface. The release kinetics of these gases during various off-normal scenarios involving loss of coolant and after heat-induced rises in temperature are of particular interest for both applications. To determine the release kinetics of hydrogen from tungsten, tungsten rods irradiated with 800 MeV protons in the Los Alamos Neutron Science Center (LANSCE) to high exposures as part of the APT project have been examined. Hydrogen evolution from the tungsten has been measured using a dedicated mass-spectrometer system by subjecting the specimens to an essentially linear temperature ramp from {approx}300 to {approx}1500 K. Release profiles are compared with predictions obtained using the Tritium Migration Analysis Program (TMAP4). The measurements show that for high proton doses, the majority of the hydrogen is released gradually, starting at about 900 K and reaching a maximum at about 1400 K, where it drops fairly rapidly. Comparisons with TMAP show quite reasonable agreement using a trap energy of 1.4 eV and a trap density of {approx}7%. There is a small additional release fraction occurring at {approx}550 K, which is believed to be associated with low-energy trapping at or near the surface, and, therefore, was not included in the bulk TMAP model.

Free release of the premises of a company according to the ''De.Minimis Concept'' - an application from the point of view of the operator and the consultant

International Nuclear Information System (INIS)

Knappik, R.; Schmidt, G.

2003-01-01

VKTA are carrying out for the Free State of Saxony the decommissioning of nuclear facilities at the Rossendorf Research Site at Dresden as well as the related tasks for waste management and free release. Therefore, concepts need to be developed of how the optimum method towards greenfield should be designed in each individual case taking into consideration the specific characteristics of the site. The facilities for waste management and storage that have been installed on part of the VKTA area and which to a large extend are below surface level have been decommissioned and the sources of contamination removed. Parts of buildings, surfaces and deeper soil layers are partly contaminated with radioactive substances. It is the final objective to free release these premises from the ambit of the Atomic Energy Act. In such a case the remaining buildings are completely removed (Method 1) which is accompanied by large-scale earth moving to remove soil contaminations for subsequent free release. In this case VKTA considers it the more intelligent and less costly solution to free release the remaining building structures and the surrounding soil on the basis of the de-minimise concept (Method 2). Taking into consideration ancillary conditions, in particular the future uses of the area and being aware of the results of the hydrogeological opinion for the Rossendorf Site, the history of the facilities and the large number of analyzed soil samples, the 10-μSv/a concept may be complied with also for the case that deeper contaminations and the remaining building structures remain in the soil. Therefore, the operator and the expert consultant will present the problem from their points of view. (orig.)

The utilization of adenosine triphosphate in rat mast cells during histamine release induced by anaphylactic reaction and compound 48/80

DEFF Research Database (Denmark)

Johansen, Torben; Chakravarty, N

1975-01-01

of ATP synthesis while a large part of the histamine release remained unaffected-a decrease in the ATP content could be demonstrated in close time relation to both anaphylactic and compound 48/80-induced histamine release. The observations indicate an increased utilization of ATP in mast cells during...

Investigating the in vitro drug release kinetics from controlled release diclofenac potassium-ethocel matrix tablets and the influence of co-excipients on drug release patterns.

Science.gov (United States)

Shah, Shefaat Ullah; Shah, Kifayat Ullah; Rehman, Asimur; Khan, Gul Majid

2011-04-01

The objective of the study was to formulate and evaluate controlled release polymeric tablets of Diclofenac Potassium for the release rate, release patterns and the mechanism involved in the release process of the drug. Formulations with different types and grades of Ethyl Cellulose Ether derivatives in several drug-to-polymer ratios (D:P) were compressed into tablets using the direct compression method. In vitro drug release studies were performed in phosphate buffer (pH 7.4) as dissolution medium by using USP Method-1 (Rotating Basket Method). Similarity factor f2 and dissimilarity factor f1 were applied for checking the similarities and dissimilarities of the release profiles of different formulations. For the determination of the release mechanism and drug release kinetics various mathematical/kinetic models were employed. It was found that all of the Ethocel polymers could significantly slow down the drug release rate with Ethocel FP polymers being the most efficient, especially at D:P ratios of 10:03 which lead towards the achievement of zero or near zero order release kinetics.

Transient modeling of electrochemically assisted CO2 capture and release

DEFF Research Database (Denmark)

Singh, Shobhana; Stechel, Ellen B.; Buttry, Daniel A.

2017-01-01

to analyze the time-dependent behavior of CO2 capture and electro-migration transport across the cell length. Given high nonlinearity of the system, we used a finite element method (FEM) to numerically solve the coupled mass transport equations. The model describes the concentration profiles by taking......The present work aims to develop a model of a new electrochemical CO2 separation and release technology. We present a one-dimensional transient model of an electrochemical cell for point source CO2 capture and release, which mainly focuses on the simultaneous mass transport and complex chemical...... reactions associated with the separation process. For concreteness, we use an ionic liquid (IL) with 2 M thiolate anion (RS−) in 1 M disulfide (RSSR) as an electrolyte in the electrochemical cell to capture, transport and release CO2 under standard operating conditions. We computationally solved the model...

Microwave Activation of Drug Release

DEFF Research Database (Denmark)

Jónasson, Sævar Þór

Due to current limitations in control of pharmaceutical drug release in the body along with increasing medicine use, methods of externally-controlled drug release are of high interest. In this thesis, the use of microwaves is proposed as a technique with the purpose of externally activating...... setup, called the microwave activation system has been developed and tested on a body phantom that emulates the human torso. The system presented in this thesis, operates unobtrusively, i.e. without physically interfering with the target (patient). The torso phantom is a simple dual-layered cylindrical...... the phantom is of interest for disclosing essential information about the limitations of the concept, the phantom and the system. For these purposes, a twofold operation of the microwave activation system was performed, which are reciprocal of each other. In the first operation phase, named mapping...

Modelling the release behaviour of cesium during severe fuel degradation

International Nuclear Information System (INIS)

Lewis, B.J.; Andre, B.; Morel, B.

1995-01-01

An analytical model has been applied to describe the diffusional release of fission product cesium from Zircaloy-clad fuel under high-temperature reactor accident conditions. The present treatment accounts for the influence of the atmosphere (i.e., changing oxygen potential) on the state of fuel oxidation and the release kinetics. The effects of fuel dissolution on the volatile release behaviour (under reducing conditions) is considered in terms of earlier crucible experiments and a simple model based on bubble coalescence and transport in metal pools. The model has been used to interpret the cesium release kinetics observed in steam and hydrogen experiments at the Vertical Irradiation (VI) Facility in the Oak Ridge National Laboratory and at the HEVA/VERCORS Facility in the Commissariat a l'Energie Atomique. (author)

EPICS release 3.11 specific documentation -- EPICS release notes for 3.11

International Nuclear Information System (INIS)

1994-01-01

EPICS release 3.11 is now ready for user testing. A person who wants to set up a simplified application environment to boot an IOC and create databases using R3.11 should follow the directions in Appendix B, page 27, of the EPICS Source/Release Control Manual, Sept. 20, 1993. The R3.11 EPICS path at ANL/APS is /net/phebos/epics/R3.11 so the command to get the new release is /net/phebos/epics/R3.11/Unix/share/bin/getrel /net/phebos/epics/R3.11. An existing R3.8 short form report can be copied to this new directory and used to create a database. ANL/APS is currently testing an Application Developers Source/Release control system. It is not yet ready for general distribution. Attached are the EPICS R3.11 release notes

Steady bound electromagnetic eigenstate arises in a homogeneous isotropic linear metamaterial with zero-real-part-of-impedance and nonzero-imaginary-part-of-wave-vector

Science.gov (United States)

Chen, Jiangwei; Dai, Yuyao; Yan, Lin; Zhao, Huimin

2018-04-01

In this paper, we shall demonstrate theoretically that steady bound electromagnetic eigenstate can arise in an infinite homogeneous isotropic linear metamaterial with zero-real-part-of-impedance and nonzero-imaginary-part-of-wave-vector, which is partly attributed to that, here, nonzero-imaginary-part-of-wave-vector is not involved with energy losses or gain. Altering value of real-part-of-impedance of the metamaterial, the bound electromagnetic eigenstate may become to be a progressive wave. Our work may be useful to further understand energy conversion and conservation properties of electromagnetic wave in the dispersive and absorptive medium and provides a feasible route to stop, store and release electromagnetic wave (light) conveniently by using metamaterial with near-zero-real-part-of-impedance.

Release mechanisms from shallow engineered trenches used as repositories for radioactive wastes

International Nuclear Information System (INIS)

Locke, J.; Wood, E.

1987-05-01

This report has been written for the Department of the Environment as part of their radioactive waste management research programme. The aim has been to identify release mechanisms of radioactivity from fully engineered trenches of the LAND 2 type and, to identify the data needed for their assessment. No direct experimental work has been involved. The report starts with a brief background to UK strategy and outlines a basic disposal system. It gives reviews of existing experience of low level radioactive waste disposal from LAND 1 trenches and of UK experience of toxic waste disposal to provide a practical basis for the next section which covers the implications of identified release mechanisms on the design requirements for an engineered trench. From these design requirements and their interaction with potential site conditions (both saturated and unsaturated zone sites are considered) an assessment of radionuclide release mechanism is made. (author)

Spatial Release From Masking in Children: Effects of Simulated Unilateral Hearing Loss.

Science.gov (United States)

Corbin, Nicole E; Buss, Emily; Leibold, Lori J

The purpose of this study was twofold: (1) to determine the effect of an acute simulated unilateral hearing loss on children's spatial release from masking in two-talker speech and speech-shaped noise, and (2) to develop a procedure to be used in future studies that will assess spatial release from masking in children who have permanent unilateral hearing loss. There were three main predictions. First, spatial release from masking was expected to be larger in two-talker speech than in speech-shaped noise. Second, simulated unilateral hearing loss was expected to worsen performance in all listening conditions, but particularly in the spatially separated two-talker speech masker. Third, spatial release from masking was expected to be smaller for children than for adults in the two-talker masker. Participants were 12 children (8.7 to 10.9 years) and 11 adults (18.5 to 30.4 years) with normal bilateral hearing. Thresholds for 50%-correct recognition of Bamford-Kowal-Bench sentences were measured adaptively in continuous two-talker speech or speech-shaped noise. Target sentences were always presented from a loudspeaker at 0° azimuth. The masker stimulus was either co-located with the target or spatially separated to +90° or -90° azimuth. Spatial release from masking was quantified as the difference between thresholds obtained when the target and masker were co-located and thresholds obtained when the masker was presented from +90° or -90° azimuth. Testing was completed both with and without a moderate simulated unilateral hearing loss, created with a foam earplug and supra-aural earmuff. A repeated-measures design was used to compare performance between children and adults, and performance in the no-plug and simulated-unilateral-hearing-loss conditions. All listeners benefited from spatial separation of target and masker stimuli on the azimuth plane in the no-plug listening conditions; this benefit was larger in two-talker speech than in speech-shaped noise. In the

Limits for the release of uranium compounds to the environment

International Nuclear Information System (INIS)

Lopez, F.; Ferruz, P.; Aguayo, A.

1987-01-01

A conservative criteria to be be followed by a Regulatory Body, in order to provide the limits of radioactive material release in the environment, When all the parameters are not available for the optimization of radiation protection is presented. This criteria can be applied to stablishment of radioactive release limits for uranium compounds from the nuclear fuel cycle facilities. (author)

Hanford Tanks 241-C-202 and 241-C-203 Residual Waste Contaminant Release Models and Supporting Data

Energy Technology Data Exchange (ETDEWEB)

Deutsch, William J.; Krupka, Kenneth M.; Lindberg, Michael J.; Cantrell, Kirk J.; Brown, Christopher F.; Mattigod, Shas V.; Schaef, Herbert T.; Arey, Bruce W.

2007-09-13

As directed by Congress, the U. S. Department of Energy (DOE) established the Office of River Protection in 1998 to manage DOE's largest, most complex environmental cleanup project – retrieval of radioactive waste from Hanford tanks for treatment and eventual disposal. Sixty percent by volume of the nation's high-level radioactive waste is stored at Hanford in aging deteriorating tanks. If not cleaned up, this waste is a threat to the Columbia River and the Pacific Northwest. CH2M Hill Hanford Group, Inc., is the Office of River Protection's prime contractor responsible for the storage, retrieval, and disposal of Hanford's tank waste. As part of this effort, CH2M HILL Hanford Group, Inc. contracted with Pacific Northwest National Laboratory (PNNL) to develop release models for key contaminants that are present in residual sludge remaining after closure of Hanford Tanks 241-C-203 (C-203) and 241-C-204 (C-204). The release models were developed from data generated by laboratory characterization and testing of samples from these two tanks. These release models are being developed to support the tank closure risk assessments performed by CH2M HILL Hanford Group, Inc., for DOE.

Proceedings of the Scientific Meeting and Presentation on Basic Research in Nuclear of the Science and Technology part III : Radioactive Waste Management and Environment

International Nuclear Information System (INIS)

Kamsul Abraha; Yateman Arryanto; Sri Jauhari S; Agus Taftazani; Kris Tri Basuki; Djoko Sardjono, Ign.; Sukarsono, R.; Samin; Syarip; Suryadi, MS; Sardjono, Y.; Tri Mardji Atmono; Dwiretnani Sudjoko; Tjipto Sujitno, BA.

2007-08-01

The Scientific Meeting and Presentation on Basic Research in Nuclear Science and Technology is a routine activity held by Centre for Accelerator Technology and Material Process, National Nuclear Energy Agency, for monitoring the research activity which achieved in National Nuclear Energy Agency. The Meeting was held in Yogyakarta on July 10, 2007. The proceedings contains papers presented on the meeting about Radioactive Waste Management and Environment and there are 25 papers which have separated index. The proceedings is the third part of the three parts which published in series. (PPIN)

Proceedings of the Scientific Meeting and Presentation on Basic Research in Nuclear of the Science and Technology part II : Nuclear Chemistry and Process Technology

International Nuclear Information System (INIS)

Kamsul Abraha; Yateman Arryanto; Sri Jauhari S; Agus Taftazani; Kris Tri Basuki; Djoko Sardjono, Ign.; Sukarsono, R.; Samin; Syarip; Suryadi, MS; Sardjono, Y.; Tri Mardji Atmono; Dwiretnani Sudjoko; Tjipto Sujitno, BA.

2007-08-01

The Scientific Meeting and Presentation on Basic Research in Nuclear Science and Technology is a routine activity held by Centre for Accelerator Technology and Material Process, National Nuclear Energy Agency, for monitoring the research activity which achieved in National Nuclear Energy Agency. The Meeting was held in Yogyakarta on July 10, 2007. The proceedings contains papers presented on the meeting about Nuclear Chemistry and Process Technology and there are 47 papers which have separated index. The proceedings is the second part of the three parts which published in series. (PPIN)

Accelerated in vitro release testing method for naltrexone loaded PLGA microspheres.

Science.gov (United States)

Andhariya, Janki V; Choi, Stephanie; Wang, Yan; Zou, Yuan; Burgess, Diane J; Shen, Jie

2017-03-30

The objective of the present study was to develop a discriminatory and reproducible accelerated release testing method for naltrexone loaded parenteral polymeric microspheres. The commercially available naltrexone microsphere product (Vivitrol ® ) was used as the testing formulation in the in vitro release method development, and both sample-and-separate and USP apparatus 4 methods were investigated. Following an in vitro drug stability study, frequent media replacement and addition of anti-oxidant in the release medium were used to prevent degradation of naltrexone during release testing at "real-time" (37°C) and "accelerated" (45°C), respectively. The USP apparatus 4 method was more reproducible than the sample-and-separate method. In addition, the accelerated release profile obtained using USP apparatus 4 had a shortened release duration (within seven days), and good correlation with the "real-time" release profile. Lastly, the discriminatory ability of the developed accelerated release method was assessed using compositionally equivalent naltrexone microspheres with different release characteristics. The developed accelerated USP apparatus 4 release method was able to detect differences in the release characteristics of the prepared naltrexone microspheres. Moreover, a linear correlation was observed between the "real-time" and accelerated release profiles of all the formulations investigated, suggesting that the release mechanism(s) may be similar under both conditions. These results indicate that the developed accelerated USP apparatus 4 method has the potential to be an appropriate fast quality control tool for long-acting naltrexone PLGA microspheres. Copyright © 2017 Elsevier B.V. All rights reserved.

Guidance for Evaluating the Safety of Experimental Releases of Mosquitoes, Emphasizing Mark-Release-Recapture Techniques.

Science.gov (United States)

Benedict, Mark Q; Charlwood, J Derek; Harrington, Laura C; Lounibos, L Philip; Reisen, William K; Tabachnick, Walter J

2018-01-01

Experimental releases of mosquitoes are performed to understand characteristics of populations related to the biology, ability to transmit pathogens, and ultimately their control. In this article, we discuss considerations related to the safety of experimental releases of living mosquitoes, applying principles of good practice in vector biology that protect human health and comfort. We describe specific factors of experimental releases of mosquitoes that we believe are critical to inform institutional biosafety committees and similar review boards to which proposals to conduct mosquito release experiments have been submitted. In this study, "experimental releases" means those that do not significantly increase vector capacity or nuisance biting relative to the unperturbed natural baseline. This document specifically does not address releases of mosquitoes for ongoing control programs or trials of new control methods for which broader assessments of risk are required. It also does not address releases of transgenic or exotic (non-native) mosquito species, both of which require particular regulatory approval. Experimental releases may include females and males and evaluation must consider their effects based on the number released, their genotype and phenotype, the environment into which they are released, and postrelease collection activities. We consider whether increases of disease transmission and nuisance biting might result from proposed experimental releases against the backdrop of natural population size variation. We recommend that experimental releases be conducted in a manner that can be reasonably argued to have insignificant negative effects. Reviewers of proposals for experimental releases should expect applicants to provide such an argument based on evidence from similar studies and their planned activities. This document provides guidance for creating and evaluating such proposals.

Influence of bicarbonate on the sensitivity of renin release to sodium chloride

DEFF Research Database (Denmark)

Skøtt, O; Jensen, B L

1989-01-01

glomeruli treated with bicarbonate/chloride exchange inhibitor (DNDS), NaCl/KCl cotransport inhibitor (bumetanide), or Na+/H+ antiport inhibitor (amiloride) in the presence or absence of bicarbonate. In addition, the sensitivity to increases in osmolality by addition of sucrose was tested in the presence...... or absence of bicarbonate. Renin release from time controls superfused with a bicarbonate-free Ringer was identical to release from glomeruli superfused with a bicarbonate Ringer. DNDS (0.11 or 1.1 mM) had no effect on renin release in a bicarbonate Ringer. 30 mM sucrose inhibited renin release independently...... of bicarbonate. 15 mM NaCl stimulated renin release when bicarbonate was absent, while it caused an inhibition in the presence of bicarbonate. When bicarbonate/chloride exchange was inhibited, addition of NaCl stimulated renin release even when bicarbonate was present. The effect of NaCl on renin release...

[The effects of various factors on the in vitro velocity of drug release from repository tablets. Part 4: Isoniazid (Rimicid) respository tablets (author's transl)].

Science.gov (United States)

Tomassini, L; Michailova, D; Naplatanova, D; Slavtschev, P

1979-12-01

The authors investigated the release of isoniazid from repository tablets as related to form, processing technology, strength constant and storage for 5 years. On determining the diffusion coefficient (D), the initial dissolution rate (Vo) and the time required for the diffusion of the releasing medium to the middle of the tablet (t1/2), it was found that the difference in release rate between the flat and the biconvex tablets is small. Furthermore, it was stated that the three-layer tablets have very high D and Vo values and very low t1/2 values, for what reason they are unsuited for repository tablets of the composition under investigation. Moreover, it was found that an increase of the strength constant does not affect the D, t1/2 and Vo values, and that the release of isoniazid is retarded only in flat tablets with the highest strength constant. Storage exerts no effect on the drug release from these tablets. The industrial production of these tablets is under way.

Repeated episodes of ozone inhalation attenuates airway injury/repair and release of substance P, but not adaptation.

Science.gov (United States)

Schelegle, Edward S; Walby, William F; Alfaro, Mario F; Wong, Viviana J; Putney, Lei; Stovall, Mary Y; Sterner-Kock, Anja; Hyde, Dallas M; Plopper, Charles G

2003-02-01

To determine the impact of repeated episodes of ozone exposure on physiologic adaptation, epithelial injury/repair, and tracheal substance P levels, adult rats were subjected to episodes of ozone (5 days, 1 ppm, 8 h/day) followed by 9 days of filtered air for four cycles. Rats were sampled on days 1 and 5 of each episode and 9 days after day 5 of episodes 1, 2, and 4. One hour before being euthanized each rat was injected with 5-bromo-2'-deoxyuridine to label proliferating cells. Each 5-day episode showed a characteristic pattern of rapid shallow breathing (days 1 and 2), epithelial injury, and interstitial and intraluminal inflammation. In contrast, the neutrophil component of inflammation, tracheal substance P release, and cell proliferation became attenuated with each consecutive episode of exposure. Concurrent with this cyclic and attenuated response there was progressive hypercellularity and hyperplasia in all airways studied and a progressive remodeling present in the terminal bronchioles. Our findings are consistent with the notion that the cumulative distal airway lesion is at least in part the result of a depressed cell proliferative response to injury in these airways. This depressed cell proliferative response may be in part the result of diminished neutrophil inflammation and/or release of mitogenic neuropeptides in response to ozone-induced injury.

Modelling transient energy release from molten fuel coolant interaction debris

International Nuclear Information System (INIS)

Fletcher, D.F.

1984-05-01

A simple model of transient energy release in a Molten Fuel Coolant Interaction is presented. A distributed heat transfer model is used to examine the effect of heat transfer coefficient, time available for rapid energy heat transfer and particle size on transient energy release. The debris is assumed to have an Upper Limit Lognormal distribution. Model predictions are compared with results from the SUW series of experiments which used thermite-generated uranium dioxide molybdenum melts released below the surface of a pool of water. Uncertainties in the physical principles involved in the calculation of energy transfer rates are discussed. (author)

Release of fission and activation products during LWR core meltdown

International Nuclear Information System (INIS)

Albrecht, H.; Matschoss, V.; Wild, H.

1978-01-01

Experiments are described by which activity release fractions and aerosol characteristics were investigated for various core melting conditions. Samples of corium and fissium were heated by induction to temperatures of 2800 0 C under air, argon and steam. Release values are presented for Cr, Mn, Fe, Co, Se, Zr, Mo, Cd, Sn, Sb, Te, J, Cs and U. The deposition behaviour of the released products was found to depend strongly on the volatility and on the gas flow rate. Preliminary results of additional measurements indicate that the size distribution of the aerosol particles is trimodal. (author)

Proceeding of the Scientific Meeting and Presentation on Basic Research in Nuclear Science and Technology. Part I : Physics, Reactor Physics and Nuclear Instrumentation

International Nuclear Information System (INIS)

Sudjatmoko; Karmanto, Eko Edy; Supartini, Endang

1996-04-01

Scientific Meeting and Presentation on Basic Research in Nuclear Science and Technology is a routine activity was held by PPNY BATAN for monitoring the research Activity which achieved in BATAN. The Proceeding contains a proposal about basic which has physics; reactor physics and nuclear instrumentation. This proceedings is the first part from two part which published in series. There are 33 articles which have separated index

Identification and assessment of containment and release management strategies

International Nuclear Information System (INIS)

Lehner, J.R.; Lin, C.C.; Neogy, P.

1990-01-01

Brookhaven National Laboratory, under the auspices of the US Nuclear Regulatory Commission, is investigating accident management strategies which could help preserve containment integrity or minimize releases during a severe accident. The objective is to make use of existing plant systems and equipment in innovative ways to reduce the likelihood of containment failure or to mitigate the release of fission products to the environment if failure cannot be prevented. Many of the strategies would be implemented during the later stages of a severe accident. The identification and assessment process for containment and release strategies is described, and some insights derived from its application to a BWR Mark 1 plant are presented here. 13 refs., 2 figs

Prevention and mitigation of groundwater contamination from radioactive releases

International Nuclear Information System (INIS)

1988-10-01

This document gives basic information on potential pathways and mechanisms, by which radioactive materials from releases can reach man, and on modelling considerations to predict the behaviour of radioactive materials in the ground. The main objective is to present an overview of existing techniques for preventing the offsite releases of contaminants into the groundwater systems and techniques for mitigation of effects of such releases should they occur. The recommended techniques are fully applicable to any hazardous materials, such as organic liquids, and toxic materials or otherwise dangerous materials, the presence of which in the accessible biosphere can represent health risks as well as economic losses to the general public. 11 refs, 2 figs, 8 tabs

Can gamma irradiation during radiotherapy influence the metal release process for biomedical CoCrMo and 316L alloys?

Science.gov (United States)

Wei, Zheng; Edin, Jonathan; Karlsson, Anna Emelie; Petrovic, Katarina; Soroka, Inna L; Odnevall Wallinder, Inger; Hedberg, Yolanda

2018-02-09

The extent of metal release from implant materials that are irradiated during radiotherapy may be influenced by irradiation-formed radicals. The influence of gamma irradiation, with a total dose of relevance for radiotherapy (e.g., for cancer treatments) on the extent of metal release from biomedical stainless steel AISI 316L and a cobalt-chromium alloy (CoCrMo) was investigated in physiological relevant solutions (phosphate buffered saline with and without 10 g/L bovine serum albumin) at pH 7.3. Directly after irradiation, the released amounts of metals were significantly higher for irradiated CoCrMo as compared to nonirradiated CoCrMo, resulting in an increased surface passivation (enhanced passive conditions) that hindered further release. A similar effect was observed for 316L showing lower nickel release after 1 h of initially irradiated samples as compared to nonirradiated samples. However, the effect of irradiation (total dose of 16.5 Gy) on metal release and surface oxide composition and thickness was generally small. Most metals were released initially (within seconds) upon immersion from CoCrMo but not from 316L. Albumin induced an increased amount of released metals from AISI 316L but not from CoCrMo. Albumin was not found to aggregate to any greater extent either upon gamma irradiation or in the presence of trace metal ions, as determined using different light scattering techniques. Further studies should elucidate the effect of repeated friction and fractionated low irradiation doses on the short- and long term metal release process of biomedical materials. © 2018 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 2018. © 2018 The Authors Journal of Biomedical Materials Research Part B: Applied Biomaterials Published by Wiley Periodicals, Inc.

Presentation of the ASTRAL software; Presentation du logiciel ASTRAL

Energy Technology Data Exchange (ETDEWEB)

NONE

2011-07-01

This report presents the ASTRAL software (ASTRAL means technical assistance in post-accidental radioprotection) which is aimed to be used as an aid-to-decision tool in the case of an important release of radionuclides in the environment by assessing radionuclide concentration in different environments and food products, determining the potential exposure to irradiation of concerned populations, foreseeing the evolution of the situation, and proposing different scenarios for the management of contaminated areas. The report describes the software general operation, presents the calculation module (main functionalities, concentration index calculation, dose calculation or radiological impact calculation, how countermeasures are taken into account), the data bases (contextual data, data for radio-ecological calculations and for radiological calculations), the software ergonomics (general principles, result selection and display, result printing and input data). Its briefly evokes the development quality assurance, and describes the software implementation architecture

Evaluating tamsulosin hydrochloride-released microparticles prepared using single-step matrix coating.

Science.gov (United States)

Maeda, Atsushi; Shinoda, Tatsuki; Ito, Naoki; Baba, Keizo; Oku, Naoto; Mizumoto, Takao

2011-04-15

The objective of the present study was to determine the optimum composition for sustained-release of tamsulosin hydrochloride from microparticles intended for orally disintegrating tablets. Microparticles were prepared from an aqueous ethylcellulose dispersion (Aquacoa®), and an aqueous copolymer based on ethyl acrylate and methyl methacrylate dispersion (Eudragit®) NE30D), with microcrystalline cellulose as core particles with a fluidized bed coating process. Prepared microparticles were about 200 μm diameter and spherical. The microparticles were evaluated for in vitro drug release and in vivo absorption to assess bioequivalence in a commercial product, Harnal® pellets. The optimum ratio of Aquacoat® and Eudragit® NE30D in the matrix was 9:1. We observed similar drug release profiles in microparticles and Harnal® pellets. Higuchi model analysis of the in vitro drug release from microparticles was linear up to 80% release, typical of Fickian diffusion sustained-release profile. The in vivo absorption properties from microparticles were comparable to Harnal® pellets, and there was a linear relationship between in vitro drug release and in vivo drug release. In conclusion, this development produces microparticles in single-step coating, that provided a sustained-release of tamsulosin hydrochloride comparable to Harnal® pellets. Copyright © 2011 Elsevier B.V. All rights reserved.

Radioactive release data from Canadian nuclear generating stations 1872-1987

International Nuclear Information System (INIS)

1989-03-01

All nuclear generating stations emit small quantities of radioactive effluent both into the atmosphere and in the form of liquid effluent, into the adjoining water body, be it river, lake or sea. The purpose of this document is to report on the magnitude of these emissions for each nuclear generating station in Canada and to indicate how these emissions compare with the relevant limitations imposed by the Atomic Energy Control Board as part of its regulatory and licensing program. This report incorporates histograms indicating the annual releases of tritium in air, noble gases, iodine-131, airborne particulates, tritium in water and waterborne gross beta activity for each nuclear generating station. In addition, for Pickering NGS 'A', annual released of carbon-14 are depicted for the years 1986 and 1987. In each case the emission data are compared to the Derived Emission Limit (DEL) in order that the data may be placed in perspective. At present, only Pickering NGS 'A' is required to monitor and report carbon-14 emissions. Environmental monitoring for C-14 is conducted around the Bruce site to determine the environmental impact of its emission and whether effluent monitoring will be necessary in future years. Three nuclear generating stations have been permanently taken out of service during the last few years (Gentilly NGS-1, Douglas Point NGS and NPD NGS). Some small emissions from these sites do still occur, however, due to decontamination and decommissioning operations. (11 tabs., 26 figs.)

Release and Degradation of Microencapsulated Spinosad and Emamectin Benzoate.

Science.gov (United States)

Huang, Bin Bin; Zhang, Shao Fei; Chen, Peng Hao; Wu, Gang

2017-09-07

The dynamics of release and degradation of the microencapsulation formulation containing spinosad (SP) and emamectin benzoate (EM) were evaluated in the present study. SP and EM were microencapsulated using biodegradable poly-lactic acid (PLA) as the wall material. Their release from and degradation within the prepared SP and EM microspheres (SP-EM-microspheres) were studied. It was found that the encapsulation significantly prolonged the insecticide release. The release could be further extended if the external aqueous phase was pre-saturated with the insecticides and the microspheres were additionally coated with gelatin. On the other hand, increasing the water content of the emulsion or the hydrophilic polycaprolactone (PCL) content in the PLA/PCL mixture accelerated the release. Due to the photolysis and hydrolysis of SP and EM by sunlight, the toxicity of the non-encapsulated insecticides in water declined continuously from 0 through the 9 th day (d), and dissipated in 13 d. In contrast, an aqueous suspension containing 5% SP-EM-microspheres maintained a mostly constant toxicity to Plutella xylostella for 17 d. The biodegradable SP-EM-microspheres showed significantly higher long-term toxicity to P. xylostella due to lower release, reduced photolysis and hydrolysis of the encapsulated insecticides, which were affected by the varied preparation conditions.

Equilibrium and kinetic models for colloid release under transient solution chemistry conditions

Science.gov (United States)

We present continuum models to describe colloid release in the subsurface during transient physicochemical conditions. Our modeling approach relates the amount of colloid release to changes in the fraction of the solid surface area that contributes to retention. Equilibrium, kinetic, equilibrium and...

Controlled release of ibuprofen by meso-macroporous silica

Science.gov (United States)

Santamaría, E.; Maestro, A.; Porras, M.; Gutiérrez, J. M.; González, C.

2014-02-01

Structured meso-macroporous silica was successfully synthesized from an O/W emulsion using decane as a dispersed phase. Sodium silicate solution, which acts as a silica source and a poly(ethylene oxide)-poly(propylene oxide)-poly(ethylene oxide) (EO19PO39EO19) denoted as P84 was used in order to stabilize the emulsion and as a mesopore template. The materials obtained were characterized through transmission electron microscopy (TEM), scanning electron microscopy (SEM), small-angle X-ray diffraction scattering (SAXS) and nitrogen adsorption-desorption isotherms. Ibuprofen (IBU) was selected as the model drug and loaded into ordered meso-macroporous materials. The effect of the materials’ properties on IBU drug loading and release was studied. The results showed that the loading of IBU increases as the macropore presence in the material is increased. The IBU adsorption process followed the Langmuir adsorption isotherm. A two-step release process, consisting of an initial fast release and then a slower release was observed. Macropores enhanced the adsorption capacity of the material; this was probably due to the fact that they allowed the drug to access internal pores. When only mesopores were present, ibuprofen was probably adsorbed on the mesopores close to the surface. Moreover, the more macropore present in the material, the slower the release behaviour observed, as the ibuprofen adsorbed in the internal pores had to diffuse along the macropore channels up to the surface of the material. The material obtained from a highly concentrated emulsion was functionalized with amino groups using two methods, the post-grafting mechanism and the co-condensation mechanism. Both routes improve IBU adsorption in the material and show good behaviour as a controlled drug delivery system.

Tritium releases, birth defects and infant deaths

International Nuclear Information System (INIS)

1991-01-01

The AECB has published a report 'Tritium releases from the Pickering Nuclear Generating Station and Birth Defects and Infant Mortality in Nearby Communities 1971-1988' (report number INFO-0401). This presents the results of a detailed analysis of deaths and birth defects occurring in infants born to mothers living in the area (25 Km radius) of the Pickering nuclear power plant, over an 18-year period. The analysis looked at the frequency of these defects and deaths in comparison to the general rate for Ontario, and also in relation to airborne and waterborne releases of tritium from the power plant. The overall conclusion was that the rates of infant death and birth defects were generally not higher in the study population than in all of Ontario. There was no prevalent relationship between these deaths and defects and tritium releases measured either at the power plant or by ground monitoring stations t some distance from the facility

Prestress Accumulation-Release Technique for Damping of Impact-Born Vibrations: Application to Self-Deployable Structures

Directory of Open Access Journals (Sweden)

Arkadiusz Mróz

2015-01-01

Full Text Available A numerical study is presented, which tailors so-called prestress accumulation-release (PAR strategy to mitigate free vibrations of frame structures. First, the concept of proposed semiactive technique is outlined and possible applications are specified. In the second part of the work a parametric study is discussed, which illustrates the potential of the method for mitigation of free vibrations induced by impact or other initial load scenarios. Special attention is given to the energy balance including all relevant contributions to the total energy of the considered dissipative system. The proposed technique shows a very high potential in mitigation of free vibrations, exceeding 99% of the reference amplitude after 5 cycles of vibration.

Design and evaluation of lornoxicam bilayered tablets for biphasic release

Directory of Open Access Journals (Sweden)

Songa Ambedkar Sunil

2012-12-01

Full Text Available The objective of the present investigation was to develop bilayered tablets of lornoxicam to achieve biphasic release pattern. A bilayered tablet, consisting of an immediate and controlled release layer, was prepared by direct compression technique. The controlled release effect was achieved by using various hydrophilic natural, semi synthetic and synthetic controlled release polymers such as xanthan gum, hydroxypropyl methylcellulose (HPMC and polyethylene oxide (PEO to modulate the release of the drug. The in vitro drug release profiles showed the biphasic release behavior in which the immediate release (IR layer containing the lornoxicam was released within 15 minutes, whereas the controlled release (CR layer controlled the drug release for up to 24 h. All the bilayered tablets formulated have followed the zero order release with non-Fickian diffusion controlled release mechanism after the initial burst release. FTIR studies revealed that there was no interaction between the drug and polymers used in the study. Statistical analysis (ANOVA showed no significant difference in the cumulative amount of drug release after 15 min, but significant difference (p O objetivo do presente trabalho foi desenvolver comprimidos bicamada de lornoxicam para atingir padrão de liberação bifásica. Preparou-se, por compressão direta, comprimido bicamada, consistindo de uma camada de liberação imediata e uma de liberação controlada. A liberação controlada foi obtida pelo uso de vários polímeros naturais hidrofílicos, semi-sintéticos e sintéticos, tais como goma xantana, hidroxipropilmetil celulose (HPMC e óxido de polietileno (PEO para modular a liberação do fármaco. Os perfis de liberação in vitro mostraram comportamento bifásico em que a camada de liberação imediata (IR contendo lornoxicam foi liberada em 15 minutos, enquanto a camada de liberação controlada (CR liberou o fármaco em mais de 24 horas, Todos os comprimidos bicamada

Computational analysis of modern HTGR fuel performance and fission product release during the HFR-EU1 irradiation experiment

Energy Technology Data Exchange (ETDEWEB)

Verfondern, Karl, E-mail: k.verfondern@fz-juelich.de [Research Center Jülich, Institute of Energy and Climate Research, 52425 Jülich (Germany); Xhonneux, André, E-mail: xhonneux@lrst.rwth-aachen.de [Research Center Jülich, Institute of Energy and Climate Research, 52425 Jülich (Germany); Nabielek, Heinz, E-mail: heinznabielek@me.com [Research Center Jülich, Monschauerstrasse 61, 52355 Düren (Germany); Allelein, Hans-Josef, E-mail: h.j.allelein@fz-juelich.de [Research Center Jülich, Institute of Energy and Climate Research, 52425 Jülich (Germany); RWTH Aachen, Chair for Reactor Safety and Reactor Technology, 52072 Aachen (Germany)

2014-07-01

Highlights: • HFR-EU1 irradiation test demonstrates high quality of HTGR spherical fuel elements. • Irradiation performance is in good agreement with German fuel performance modeling. • International benchmark exercise expected first particle to fail at ∼13–17% FIMA. • EOL silver release is predicted to be in the percentage range. • EOL cesium and strontium are expected to remain at a low level. - Abstract: Various countries engaged in the development and fabrication of modern HTGR fuel have initiated activities of modeling the fuel and fission product release behavior with the aim of predicting the fuel performance under HTGR operating and accident conditions. Verification and validation studies are conducted by code-to-code benchmarking and code-to-experiment comparisons as part of international exercises. The methodology developed in Germany since the 1980s represents valuable and efficient tools to describe fission product release from spherical fuel elements and TRISO fuel performance, respectively, under given conditions. Continued application to new results of irradiation and accident simulation testing demonstrates the appropriateness of the models in terms of a conservative estimation of the source term as part of interactions with HTGR licensing authorities. Within the European irradiation testing program for HTGR fuel and as part of the former EU RAPHAEL project, the HFR-EU1 irradiation experiment explores the potential for high performance of the presently existing German and newly produced Chinese fuel spheres under defined conditions up to high burnups. The fuel irradiation was completed in 2010. Test samples are prepared for further postirradiation examinations (PIE) including heatup simulation testing in the KÜFA-II furnace at the JRC-ITU, Karlsruhe, to be conducted within the on-going ARCHER Project of the European Commission. The paper will describe the application of the German computer models to the HFR-EU1 irradiation test and

The initial phase of sudden releases of superheated liquid

International Nuclear Information System (INIS)

Schmidli, J.

1994-04-01

The catastrophic failure of a pressure vessel containing a liquefied substance, leading to an instantaneous release of its whole contents is considered as one of the major technological hazards. Due to the rapid depressurization caused by vessel failure, the fluid becomes superheated and unstable. Part of the fluid will evaporate using its internal energy and the two-phase mixture forming will be accelerated. This flashing process can be very violent, as experiments and incidents actually happened have shown. In the past, a number of dispersion models were developed to predict the history of an instantaneous release. In most of these models the source term is considered to be a gas volume at rest and not a rapidly expanding aerosol, as could be observed. Furthermore, it is usually assumed that all of the remaining fluid is entrained into the expanding cloud and nothing is deposited on the ground to form a pool. This work concentrates on the initial phase of the sudden release of superheated liquids with the aim to gain a better understanding of the flashing process and of the physical mechanisms involved, leading to a reliable prediction of the source term. Therefore, more than 400 experiments with propane, butane, refrigerant 12 and 114 were conducted. The experiments were initiated by shattering spherical glass flasks of different sizes. The main parameters varied were the liquid superheat and the filling level of the vessel. Using high-speed video and movie recordings and very fast responding measurement devices, it was possible to study the initial phase of such releases during which gravity plays no role. For sufficiently large released internal energy, the initial evolution of the release was always spherical with a constant radial expansion velocity during he first milliseconds until instabilities appeared at the surface of the droplet/vapor cloud that was formed. For all the experimental conditions, the fraction of the initial liquid falling on the ground

Design and characteristics of gellan gum beads for modified release of meloxicam.

Science.gov (United States)

Osmałek, Tomasz; Milanowski, Bartłomiej; Froelich, Anna; Szybowicz, Mirosław; Białowąs, Wojciech; Kapela, Marcin; Gadziński, Piotr; Ancukiewicz, Katarzyna

2017-08-01

The aim of the presented work was to design, formulate and evaluate the properties of low-acyl gellan macro beads with the potential application as carriers for oral delivery of meloxicam (MLX) in the prophylaxis of colorectal cancer. The beads were obtained by means of ionotropic gelation technique. Calcium chloride (1.0%, 9.0 × 10 -2  M) was used as the cross-linking agent. Nine different polymer, drug and surfactant (Tween ® 80) mixtures were used for production of the beads. The quantitative compositions of the mixtures were generated with the application of the Design of Experiments (DoE) modulus from the STATISTICA Software. The prepared formulations revealed 7.2-27.0% of drug loading and 29.2-50.7% drug encapsulation efficiency. It turned out that 0.5% amount of gellan gum in the mixtures was not sufficient to obtain spherical beads. The morphology and surface of the dried beads were analyzed by SEM. Raman spectra confirmed that MLX did not undergo structural changes during production of the beads. The swelling behavior and degradation of the beads were evaluated in three simulated gastrointestinal fluids at different pH (1.2; 4.5; 6.8). The MLX in vitro release studies were conducted on USP apparatus IV, working in the open loop mode. The obtained results showed that MLX release from the dried beads was pH-dependent. The formulations obtained from mixtures containing 1.0 and 1.5% of gellan may be considered as oral dosage forms for MLX, intended to omit the stomach and release the drug in the distal parts of the gastrointestinal tract.

Loose-parts monitoring: present status of the technology, its implementation in U.S. reactors, and some recommendations for achieving improved performance

International Nuclear Information System (INIS)

Kryter, R.C.; Ricker, C.W.; Jones, J.E.

1977-01-01

An assessment of the technical development status of loose-parts monitoring systems (LPMS) and their performance record to data in commercial light-water-cooled nuclear reactor plants was made during the spring of 1977, using an on-site personal interview and equipment demonstration approach. The study revealed that while presently demonstrated LPMS technology does indeed provide a capability for detecting the presence of those relatively massive loose parts that would likely constitute a serious operational or safety hazard to the plant, it unfortunately affords little information useful to the determination of the parts' safety significance and has not yet attained the levels of sophistication and reliability ordinarily associated with safety systems. A definite need was found for specification of the functional requirements for LPMS, in the form of a clear and comprehensive statement of NRC policy regarding the formulation and implementation of safety-oriented, yet operationally practicable, loose-parts monitoring programs for both existing and future nuclear generating stations so that overall objectives of both the utilities and the regulatory agency might be satisfied simultaneously

Osmotic pressure-dependent release profiles of payloads from nanocontainers by co-encapsulation of simple salts

Science.gov (United States)

Behzadi, Shahed; Rosenauer, Christine; Kappl, Michael; Mohr, Kristin; Landfester, Katharina; Crespy, Daniel

2016-06-01

The encapsulation of payloads in micro- to nano-scale capsules allows protection of the payload from the surrounding environment and control of its release profile. Herein, we program the release of hydrophilic payloads from nanocontainers by co-encapsulating simple inorganic salts for adjusting the osmotic pressure. The latter either leads to a burst release at high concentrations of co-encapsulated salts or a sustained release at lower concentrations. Osmotic pressure causes swelling of the nanocapsule's shell and therefore sustained release profiles can be adjusted by crosslinking it. The approach presented allows for programing the release of payloads by co-encapsulating inexpensive salts inside nanocontainers without the help of stimuli-responsive materials.The encapsulation of payloads in micro- to nano-scale capsules allows protection of the payload from the surrounding environment and control of its release profile. Herein, we program the release of hydrophilic payloads from nanocontainers by co-encapsulating simple inorganic salts for adjusting the osmotic pressure. The latter either leads to a burst release at high concentrations of co-encapsulated salts or a sustained release at lower concentrations. Osmotic pressure causes swelling of the nanocapsule's shell and therefore sustained release profiles can be adjusted by crosslinking it. The approach presented allows for programing the release of payloads by co-encapsulating inexpensive salts inside nanocontainers without the help of stimuli-responsive materials. Electronic supplementary information (ESI) available. See DOI: 10.1039/c6nr01882c

Release of a Poorly Soluble Drug from Hydrophobically Modified Poly (Acrylic Acid in Simulated Intestinal Fluids.

Directory of Open Access Journals (Sweden)

Patrik Knöös

Full Text Available A large part of new pharmaceutical substances are characterized by a poor solubility and high hydrophobicity, which might lead to a difference in drug adsorption between fasted and fed patients. We have previously evaluated the release of hydrophobic drugs from tablets based on Pemulen TR2 and showed that the release can be manipulated by adding surfactants. Here we further evaluate the possibility to use Pemulen TR2 in controlled release tablet formulations containing a poorly soluble substance, griseofulvin. The release is evaluated in simulated intestinal media that model the fasted state (FaSSIF medium or fed state (FeSSIF. The rheology of polymer gels is studied in separate experiments, in order to gain more information on possible interactions. The release of griseofulvin in tablets without surfactant varied greatly and the slowest release were observed in FeSSIF. Addition of SDS to the tablets eliminated the differences and all tablets showed a slow linear release, which is of obvious relevance for robust drug delivery. Comparing the data from the release studies and the rheology experiment showed that the effects on the release from the different media could to a large extent be rationalised as a consequence of the interactions between the polymer and the surfactants in the media. The study shows that Pemulen TR2 is a candidate for controlled release formulations in which addition of surfactant provides a way to eliminate food effects on the release profile. However, the formulation used needs to be designed to give a faster release rate than the tablets currently investigated.

FEBEX. Investigations on gas generation, release and migration

International Nuclear Information System (INIS)

Jockwer, Norbert; Wieczorek, Klaus

2008-06-01

The FEBEX project is based on the Spanish reference concept for the disposal of radioactive waste in crystalline rock, which considers the emplacement of the canisters enclosing the conditioned waste surrounded by clay barriers constructed of high-compacted bentonite blocks in horizontal drifts /ENR 957. The whole project consisted of an experimental and a modelling part. The experimental part itself was divided into the in-situ test, a mock-up test performed at the CIEMAT laboratory, and various small-scale laboratory tests. In the modelling part it was expected to develop and validate the thermo-hydro-mechanical (THM) and the thermo-hydro-chemical (THC) processes for the performance assessment of the near-field behaviour. GRS was only involved in the in-situ test and some additional laboratory work with regard to gas generation, gas migration, and pore pressure build-up in the buffer constructed of high-compacted bentonite blocks around the electrical heaters simulating the waste containers. The following topics are covered: installation and dismantling of the heater pipes; methods of gas generation and release measurement, summary of results and discussion

Pneumatic transport system development: residuals and releases program at Westinghouse Cheswick site

International Nuclear Information System (INIS)

Larouere, P.J.; Shoulders, J.L.

1979-01-01

Plutonium oxide and uranium oxide powders are processed within glove boxes or within confinement systems during the fabrication of mixed oxide (MOX) pellets for recycle fuel. The release of these powders to the glove box or to the confinement results in some airborne material that is deposited in the enclosure or is carried in the air streams to the effluent air filtration system. Release tests on simulated leaks in pneumatic transport equipment and release tests on simulated failures with powder blending equipment were conducted. A task to develop pneumatic transport for the movement of powders within an MOX fabrication plant has been underway at the Westinghouse Research Laboratories. While testing and evaluating selected pneumatic transport components on a full scale were in progress, it was deemed necessary that final verification of the technology would have to be performed with plutonium-bearing powders because of the marked differences in certain properties of plutonium from those of uranium oxides. A smaller was designed and constructed for the planned installation in glove boxes at the Westinghouse Plutonium Fuel Development Laboratory. However, prior to use with plutonium it was agreed that this system be set up and tested with uranium oxide powder. The test program conducted at the Westinghouse Cheswick site was divided into two major parts. The first of these examined the residuals left as a result of the pneumatic transport of nuclear fuel powders and verified the operability of this one-third scale system. The second part of the program studied the amount of powder released to the air when off-standard process procedures or maintenance operations were conducted on the pneumatic transport system. Air samplers located within the walk-in box housing the transport loop were used to measure the solids concentration in the air. From this information, the total amount of airborne powder was determined

Surface radiological free release program for the Battelle Columbus Laboratory Decommissioning Project

International Nuclear Information System (INIS)

Horton, C.N.

1995-01-01

This paper was prepared for the Second Residual Radioactivity and Recycling Criteria Workshop and discusses decommissioning and decontamination activities at the Battelle Columbus Laboratories Decommissioning Project (BCLDP). The BCLDP is a joint effort between the Department of Energy (DOE) and Battelle Columbus Operations to decontaminate fifteen Battelle-owned buildings contaminated with DOE radioactive materials. The privately owned buildings located across the street from The Ohio State University campus became contaminated with natural uranium and thorium during nuclear research activities. BCLDP waste management is supported by an extensive radiological free-release program. Miscellaneous materials and building surfaces have been free-released from the BCLDP. The free-release program has substantially reduced radioactive waste volumes and supported waste minimization. Free release for unrestricted use has challenged regulators and NRC licensees since the development of early surface-release criteria. This paper discusses the surface radiological free-release program incorporated by the BCLDP and the historical development of the surface radiological free-release criteria. Concerns regarding radiological free-release criteria are also presented. (author)

ATP Release Channels

Directory of Open Access Journals (Sweden)

Akiyuki Taruno

2018-03-01

Full Text Available Adenosine triphosphate (ATP has been well established as an important extracellular ligand of autocrine signaling, intercellular communication, and neurotransmission with numerous physiological and pathophysiological roles. In addition to the classical exocytosis, non-vesicular mechanisms of cellular ATP release have been demonstrated in many cell types. Although large and negatively charged ATP molecules cannot diffuse across the lipid bilayer of the plasma membrane, conductive ATP release from the cytosol into the extracellular space is possible through ATP-permeable channels. Such channels must possess two minimum qualifications for ATP permeation: anion permeability and a large ion-conducting pore. Currently, five groups of channels are acknowledged as ATP-release channels: connexin hemichannels, pannexin 1, calcium homeostasis modulator 1 (CALHM1, volume-regulated anion channels (VRACs, also known as volume-sensitive outwardly rectifying (VSOR anion channels, and maxi-anion channels (MACs. Recently, major breakthroughs have been made in the field by molecular identification of CALHM1 as the action potential-dependent ATP-release channel in taste bud cells, LRRC8s as components of VRACs, and SLCO2A1 as a core subunit of MACs. Here, the function and physiological roles of these five groups of ATP-release channels are summarized, along with a discussion on the future implications of understanding these channels.

Carbon-14 releases from an unsaturated repository: A senseless but expensive dilemma

International Nuclear Information System (INIS)

Pflum, C.G.

1993-01-01

The purpose of the US Environmental Protection Agency (EPA) Environmental Standards for the Management and Disposal of Spent Nuclear Fuel, High-Level and Transuranic Radioactive Wastes (40 CFR Part 191 or standards) is to protect public health and safety. The 1985 rule was developed on the basis of the assumption that the repository would be located in a geologic formation that lies below the water table. It is appropriate to examine gaseous releases and transport of pollutants in order to determine site adequacy. When the provisions of the 1985 standard are applied to Yucca Mountain, specifically the limits for carbon-14, we can release in 10,000 years no more than 7,000 curies of carbon-14 in the form of carbon dioxide. Meanwhile, the US Department of Energy (DOE) and others indicate that the repository may release about 8,000 curies of carbon-14 dioxide, an amount that exceeds the standard by 10 to 20 percent. The original basis of the 1985 standards was that, in a site below the water table, the limit for carbon-14 was technically achievable. It was not a standard based on a release level that would prevent a danger to public health. If we examine the danger to public health of the release of 8,000 curies of carbon-14 dioxide during and 8,000-year period, this release would not a pose a significant threat to the average individual. Industry and natural sources release many times this amount of carbon-14 dioxide each year. The question therefore becomes: is it appropriate to spend an additional $3.2 billion on waste packages when the expenditure does not measurably improve the public health?

Rapid Retinal Release from a Cone Visual Pigment Following Photoactivation*

Science.gov (United States)

Chen, Min-Hsuan; Kuemmel, Colleen; Birge, Robert R.; Knox, Barry E.

2012-01-01

As part of the visual cycle, the retinal chromophore in both rod and cone visual pigments undergoes reversible Schiff base hydrolysis and dissociation following photobleaching. We characterized light-activated retinal release from a short-wavelength sensitive cone pigment (VCOP) in 0.1% dodecyl maltoside using fluorescence spectroscopy. The half-time (t1/2) of retinal release from VCOP was 7.1 s, 250-fold faster than rhodopsin. VCOP exhibited pH-dependent release kinetics, with the t1/2 decreasing from 23 s to 4 s with pH 4.1 to 8, respectively. However, the Arrhenius activation energy (Ea) for VCOP derived from kinetic measurements between 4° and 20°C was 17.4 kcal/mol, similar to 18.5 kcal/mol for rhodopsin. There was a small kinetic isotope (D2O) effect in VCOP, but less than that observed in rhodopsin. Mutation of the primary Schiff base counterion (VCOPD108A) produced a pigment with an unprotonated chromophore (⌊max = 360 nm) and dramatically slowed (t1/2 ~ 6.8 min) light-dependent retinal release. Using homology modeling, a VCOP mutant with two substitutions (S85D/ D108A) was designed to move the counterion one alpha helical turn into the transmembrane region from the native position. This double mutant had a UV-visible absorption spectrum consistent with a protonated Schiff base (⌊max = 420 nm). Moreover, VCOPS85D/D108A mutant had retinal release kinetics (t1/2 = 7 s) and Ea (18 kcal/mol) similar to the native pigment exhibiting no pH-dependence. By contrast, the single mutant VCOPS85D had a ~3-fold decrease in retinal release rate compared to the native pigment. Photoactivated VCOPD108A had kinetics comparable to a rhodopsin counterion mutant, RhoE113Q, both requiring hydroxylamine to fully release retinal. These results demonstrate that the primary counterion of cone visual pigments is necessary for efficient Schiff base hydrolysis. We discuss how the large differences in retinal release rates between rod and cone visual pigments arise, not from

32 CFR Appendix A to Part 45 - DD Form 214

Science.gov (United States)

2010-07-01

... 32 National Defense 1 2010-07-01 2010-07-01 false DD Form 214 A Appendix A to Part 45 National... CERTIFICATE OF RELEASE OR DISCHARGE FROM ACTIVE DUTY (DD FORM 214/5 SERIES) Pt. 45, App. A Appendix A to Part 45—DD Form 214 EC23OC91.003 EC23OC91.004 EC23OC91.005 EC23OC91.006 [54 FR 9985, Mar. 9, 1989] ...

Iodine-131 releases from the Hanford Site, 1944--1947

International Nuclear Information System (INIS)

Heeb, C.M.

1992-10-01

Detailed results of the Hanford Environmental Dose Reconstruction (HEDR) iodine-131 release reconstruction are presented in this volume. Included are daily data on B, D, and F Plant, reactor operations from the P-Department Daily Reports (General Electric Company 1947). Tables of B and T Plant material processed from the three principal sources on separations plant operations: The Jaech report (Jaech undated), the 200 Area Report (Acken and Bird 1945; Bird and Donihee 1945), and the Metal History Reports (General Electric Company 1946). A transcription of the Jaech report is also provided because it is computer-generated and is not readily readable in its original format. The iodine-131 release data are from the STRM model. Cut-by-cut release estimates are provided, along with daily, monthly, and yearly summations. These summations are based on the hourly release estimates. The hourly data are contained in a 28 megabyte electronic file. Interested individuals may request a copy

Encapsulation of Volatile Citronella Essential Oil by Coacervation: Efficiency and Release Study

Science.gov (United States)

Manaf, M. A.; Subuki, I.; Jai, J.; Raslan, R.; Mustapa, A. N.

2018-05-01

The volatile citronella essential oil was encapsulated by simple coacervation and complex coacervation using Arabic gum and gelatin as wall material. Glutaraldehyde was used in the methodology as crosslinking agent. The citronella standard calibration graph obtained with R2 of 0.9523 was used for the accurate determination of encapsulation efficiency and release study. The release kinetic was analysed based on Fick"s law of diffusion for polymeric system and linear graph of Log fraction release over Log time was constructed to determine the release rate constant, k and diffusion coefficient, n. Both coacervation methods in the present study produce encapsulation efficiency around 94%. The produced capsules for both coacervation processes were discussed based on the capsules morphology and release kinetic mechanisms.

Pharmacokinetic comparison of controlled-release and immediate-release oral formulations of simvastatin in healthy Korean subjects: a randomized, open-label, parallel-group, single- and multiple-dose study.

Science.gov (United States)

Jang, Seong Bok; Lee, Yoon Jung; Lim, Lay Ahyoung; Park, Kyung-Mi; Kwon, Bong-Ju; Woo, Jong Soo; Kim, Yong-Il; Park, Min Soo; Kim, Kyung Hwan; Park, Kyungsoo

2010-01-01

A controlled-release (CR) formulation of simvastatin was recently developed in Korea. The formulation is expected to yield a lower C(max) and similar AUC values compared with the immediate-release (IR) formulation. The goal of this study was to compare the pharmacokinetics of the new CR formulation and an IR formulation of simvastatin after single- and multiple-dose administration in healthy Korean subjects. This study was developed as part of a product development project at the request of the Korean regulatory agency. This was a randomized, open-label, parallelgroup, 2-part study. Eligible subjects were healthy male or female volunteers between the ages of 19 and 55 years and within 20% of their ideal weight. In part I, each subject received a single dose of the CR or IR formulation of simvastatin 40 mg orally (20 mg x 2 tablets) after fasting. In part II, each subject received the same dose of the CR or IR formulation for 8 consecutive days. Blood samples were obtained for 48 hours after the dose in part I and after the first and the last dose in part II. Pharmacokinetic parameters were determined for both simvastatin (the inactive prodrug) and simvastatin acid (the active moiety). An adverse event (AE) was defined as any unfavorable sign (including an abnormal laboratory finding) or symptom, regardless of whether it had a causal relationship with the study medication. Serious AEs were defined as any events that are considered life threatening, require hospitalization or prolongation of existing hospitalization, cause persistent or significant disability or incapacity, or result in congenital abnormality, birth defect, or death. AEs were determined based on patient interviews and physical examinations. Twenty-four healthy subjects (17 men, 7 women; mean [SD] age, 29 [7] years; age range, 22-50 years) were enrolled in part I, and 29 subjects (17 men, 12 women; mean age, 33 [9] years; age range, 19-55 years) were enrolled in part II. For simvastatin acid, C

Release kinetics of tocopherol and quercetin from binary antioxidant controlled-release packaging films.

Science.gov (United States)

Chen, Xi; Lee, Dong Sun; Zhu, Xuntao; Yam, Kit L

2012-04-04

This paper investigated the feasibility of manipulating packaging polymers with various degrees of hydrophobicity to release two antioxidants, tocopherol and quercetin, at rates suitable for long-term inhibition of lipid oxidation in food. For example, one antioxidant can be released at a fast rate to provide short-term/intermediate protection, whereas the other antioxidant can be released at a slower rate to provide intermediate/long-term protection of lipid oxidation. Controlled-release packaging films containing tocopherol and quercetin were produced using ethylene vinyl alcohol (EVOH), ethylene vinyl acetate (EVA), low-density polyethylene (LDPE), and polypropylene (PP) polymers; the release of these antioxidants to 95% ethanol (a fatty food simulant) was measured using UV-vis spectrophotometry, and Fickian diffusion models with appropriate initial and boundary conditions were used to fit the data. For films containing only quercetin, the results show that the release of quercetin was much faster but lasted for a much shorter time for hydrophilic polymers (EVOH and EVA) than for hydrophobic polymers (LDPE and PP). For binary antioxidant films containing tocopherol and quercetin, the results show that tocopherol released more rapidly but for a shorter period of time than quercetin in LDPE and EVOH films, and the difference is more pronounced for LDPE films than EVOH films. The results also show the presence of tocopherol can accelerate the release of quercetin. Although none of the films produced is acceptable for long-term lipid oxidation inhibition, the study provides encouraging results suggesting that acceptable films may be produced in the future using polymer blend films.

Preliminary analysis of public dose from CFETR gaseous tritium release

Energy Technology Data Exchange (ETDEWEB)

Nie, Baojie [Key Laboratory of Neutronics and Radiation Safety, Institute of Nuclear Energy Safety Technology, Chinese Academy of Sciences, Hefei, Anhui 230031 (China); University of Science and Technology of China, Hefei, Anhui 230027 (China); Ni, Muyi, E-mail: muyi.ni@fds.org.cn [Key Laboratory of Neutronics and Radiation Safety, Institute of Nuclear Energy Safety Technology, Chinese Academy of Sciences, Hefei, Anhui 230031 (China); Lian, Chao; Jiang, Jieqiong [Key Laboratory of Neutronics and Radiation Safety, Institute of Nuclear Energy Safety Technology, Chinese Academy of Sciences, Hefei, Anhui 230031 (China)

2015-02-15

Highlights: • Present the amounts and limit dose of tritium release to the environment for CFETR. • Perform a preliminary simulation of radiation dose for gaseous tritium release. • Key parameters about soil types, wind speed, stability class, effective release height and age were sensitivity analyzed. • Tritium release amount is recalculated consistently with dose limit in Chinese regulation for CFETR. - Abstract: To demonstrate tritium self-sufficiency and other engineering issues, the scientific conception of Chinese Fusion Engineering Test Reactor (CFETR) has been proposed in China parallel with ITER and before DEMO reactor. Tritium environmental safety for CFETR is an important issue and must be evaluated because of the huge amounts of tritium cycling in reactor. In this work, different tritium release scenarios of CFETR and dose limit regulations in China are introduced. And the public dose is preliminarily analyzed under normal and accidental events. Furthermore, after finishing the sensitivity analysis of key input parameters, the public dose is reevaluated based on extreme parameters. Finally, tritium release amount is recalculated consistently with the dose limit in Chinese regulation for CFETR, which would provide a reference for tritium system design of CFETR.

Thermosensitive liposomes entrapping iron oxide nanoparticles for controllable drug release

International Nuclear Information System (INIS)

Tai, L-A; Wang, Y-C; Wang, Y-J; Yang, C-S; Tsai, P-J; Lo, L-W

2009-01-01

Iron oxide nanoparticles can serve as a heating source upon alternative magnetic field (AMF) exposure. Iron oxide nanoparticles can be mixed with thermosensitive nanovehicles for hyperthermia-induced drug release, yet such a design and mechanism may not be suitable for controllable drug release applications in which the tissues are susceptible to environmental temperature change such as brain tissue. In the present study, iron oxide nanoparticles were entrapped inside of thermosensitive liposomes for AMF-induced drug release while the environmental temperature was maintained at a constant level. Carboxyfluorescein was co-entrapped with the iron oxide nanoparticles in the liposomes as a model compound for monitoring drug release and environmental temperature was maintained with a water circulator jacket. These experiments have been successfully performed in solution, in phantom and in anesthetized animals. Furthermore, the thermosensitive liposomes were administered into rat forearm skeletal muscle, and the release of carboxylfluorescein triggered by the external alternative magnetic field was monitored by an implanted microdialysis perfusion probe with an on-line laser-induced fluorescence detector. In the future such a device could be applied to simultaneous magnetic resonance imaging and non-invasive drug release in temperature-sensitive applications.

Radionuclide release from PWR spent fuel specimens with induced cladding defects

International Nuclear Information System (INIS)

Wilson, C.N.; Oversby, V.M.

1984-03-01

Radionuclide releases from pressurized water reactor (PWR) spent fuel rod specimens containing various artificially induced cladding defects were compared by leach testing. The study was conducted in support of the Nevada Nuclear Waste Storage Investigations (NNWSI) Waste Package Task to evaluate the effectiveness of failed cladding as a barrier to radionuclide release. Test description and results are presented

Experimental study on hydrodynamics of the up-draught part of the VK-50 boiling water reactor

International Nuclear Information System (INIS)

Fedulin, V.N.; Shmelev, V.E.; Solodkij, V.A.; Kharitonov, Yu.V.

1982-01-01

The investigation results on steam content distribution in the volume of the up-draught part of the VK 50 reactor on the basis of the electrical sounding method are presented. The operating conditions of the up-draught part of a large diameter and limited height is characterized by hydrodynamic non-uniformity of distribution of steam content field over its volume. In the up-draught part of the reactor owing to its limited height hydrodynamic flow stabilization over the section is not attained. The higher void fraction in the central region of the up-draught part (owing to higher energy release in the centre of the core) causes accelerated coolant motion upwatds which results in steam migration from the periphery to the centre and to increase of general non-uniformity of steam distribution. The revealed steam distribution non-uniformity over the height and radius of the up-draught part elucidates the discrepancy of experimental and calculation values of the average volumetric steam content and determines the necessity of the development of new calculation methods

High-performance liquid chromatography method for the determination of hydrogen peroxide present or released in teeth bleaching kits and hair cosmetic products.

Science.gov (United States)

Gimeno, Pascal; Bousquet, Claudine; Lassu, Nelly; Maggio, Annie-Françoise; Civade, Corinne; Brenier, Charlotte; Lempereur, Laurent

2015-03-25

This manuscript presents an HPLC/UV method for the determination of hydrogen peroxide present or released in teeth bleaching products and hair products. The method is based on an oxidation of triphenylphosphine into triphenylphosphine oxide by hydrogen peroxide. Triphenylphosphine oxide formed is quantified by HPLC/UV. Validation data were obtained using the ISO 12787 standard approach, particularly adapted when it is not possible to make reconstituted sample matrices. For comparative purpose, hydrogen peroxide was also determined using ceric sulfate titrimetry for both types of products. For hair products, a cross validation of both ceric titrimetric method and HPLC/UV method using the cosmetic 82/434/EEC directive (official iodometric titration method) was performed. Results obtained for 6 commercialized teeth whitening products and 5 hair products point out similar hydrogen peroxide contain using either the HPLC/UV method or ceric sulfate titrimetric method. For hair products, results were similar to the hydrogen peroxide content using the cosmetic 82/434/EEC directive method and for the HPLC/UV method, mean recoveries obtained on spiked samples, using the ISO 12787 standard, ranges from 100% to 110% with a RSDhydrogen peroxide contents higher than the regulated limit. Copyright © 2015 Elsevier B.V. All rights reserved.

PCDD/PCDF release inventories

Energy Technology Data Exchange (ETDEWEB)

Fiedler, H. [UNEP Chemicals, Chatelaine (Switzerland)

2004-09-15

The Stockholm Convention on Persistent Organic Pollutants (POPs) entered into force on 17 May 2004 with 50 Parties. In May 2004, 59 countries had ratified or acceded the Convention. The objective of the Convention is ''to protect human health and the environment from persistent organic pollutants''. For intentionally produced POPs, e.g., pesticides and industrial chemicals such as hexachlorobenzene and polychlorinated biphenyls, this will be achieved by stop of production and use. For unintentionally generated POPs, such as polychlorinated dibenzo-pdioxins (PCDD) and polychlorinated dibenzofurans (PCDF), measures have to be taken to ''reduce the total releases derived from anthropogenic sources''; the final goal is ultimate elimination, where feasible. Under the Convention, Parties have to establish and maintain release inventories to prove the continuous release reduction. Since many countries do not have the technical and financial capacity to measure all releases from all potential PCDD/PCDF sources, UNEP Chemicals has developed the ''Standardized Toolkit for the Identification of Quantification of Dioxin and Furan Releases'' (''Toolkit'' for short), a methodology to estimate annual releases from a number of sources. With this methodology, annual releases can be estimated by multiplying process-specific default emission factors provided in the Toolkit with national activity data. At the seventh session of the Intergovernmental Negotiating Committee, the Toolkit was recommended to be used by countries when reporting national release data to the Conference of the Parties. The Toolkit is especially used by developing countries and countries with economies in transition where no measured data are available. Results from Uruguay, Thailand, Jordan, Philippines, and Brunei Darussalam have been published.

Controlled-release tablet formulation of isoniazid.

Science.gov (United States)

Jain, N K; Kulkarni, K; Talwar, N

1992-04-01

Guar (GG) and Karaya gums (KG) alone and in combination with hydroxy-propylmethylcellulose (HPMC) were evaluated as release retarding materials to formulate a controlled-release tablet dosage form of isoniazid (1). In vitro release of 1 from tablets followed non-Fickian release profile with rapid initial release. Urinary excretion studies in normal subjects showed steady-state levels of 1 for 13 h. In vitro and in vivo data correlated (r = 0.9794). The studies suggested the potentiality of GG and KG as release retarding materials in formulating controlled-release tablet dosage forms of 1.

Delivery presentations

Science.gov (United States)

... has entered the pelvis. If the presenting part lies above the ischial spines, the station is reported ... M. is also a founding member of Hi-Ethics and subscribes to the principles of the Health ...

Modulation of Neutrophil Extracellular Trap and Reactive Oxygen Species Release by Periodontal Bacteria.

Science.gov (United States)

Hirschfeld, Josefine; White, Phillipa C; Milward, Michael R; Cooper, Paul R; Chapple, Iain L C

2017-12-01

Oral bacteria are the main trigger for the development of periodontitis, and some species are known to modulate neutrophil function. This study aimed to explore the release of neutrophil extracellular traps (NETs), associated antimicrobial proteins, and reactive oxygen species (ROS) in response to periodontal bacteria, as well as the underlying pathways. Isolated peripheral blood neutrophils were stimulated with 19 periodontal bacteria. NET and ROS release, as well as the expression of NET-bound antimicrobial proteins, elastase, myeloperoxidase, and cathepsin G, in response to these species was measured using fluorescence-based assays. NET and ROS release was monitored after the addition of NADP (NADPH) oxidase pathway modulators and inhibitors of Toll-like receptors (TLRs). Moreover, bacterial entrapment by NETs was visualized microscopically, and bacterial killing was assessed by bacterial culture. Certain microorganisms, e.g., Veillonella parvula and Streptococcus gordonii , stimulated higher levels of ROS and NET release than others. NETs were found to entrap, but not kill, all periodontal bacteria tested. NADPH oxidase pathway modulators decreased ROS production but not NET production in response to the bacteria. Interestingly, TLR inhibitors did not impact ROS and NET release. These data suggest that the variability in the neutrophil response toward different bacteria may contribute to the pathogenesis of periodontal diseases by mechanisms such as bacterial avoidance of host responses and activation of neutrophils. Moreover, our results indicate that bacterium-stimulated NET release may arise in part via NADPH oxidase-independent mechanisms. The role of TLR signaling in bacterium-induced ROS and NET release needs to be further elucidated. Copyright © 2017 American Society for Microbiology.

Modelling of Pb release during Portland cement alteration

Energy Technology Data Exchange (ETDEWEB)

Benard, A. [INERIS Mediterrannee, F-13545 Aix En Provence 04 (France); Rose, J.; Borschneck, D.; Bottero, J.Y. [Univ Paul Cezanne, CNRS, UMR 6635, CEREGE, IFR PMSE 112, F-13545 Aix En Provence, (France); Hazemann, J.L. [CNRS, Cristallog Lab, F-38042 Grenoble 09 (France); Proux, O. [Univ Grenoble 1, CNRS, UMR, LGIT, F-38400 St Martin Dheres (France); Trotignon, L. [CEA Cadarache, DTN, SMTM, Lab Modelisat Transferts Environm, 13 - Saint Paul lez Durance (France); Nonat, A. [Univ Bourgogne, CNRS, UMR 5613, Fac Sci Mirande, Lab Rech Reactivite Solides, F-21078 Dijon (France); Chateau, L. [ADEME, F-49004 Angers (France)

2009-07-01

Complex cementitious matrices undergo weathering with environmental exchange and can release metallic pollutants during alteration. The molecular mechanisms responsible for metal release are difficult to identify, though this is necessary if such processes are to be controlled. The present study determines and models the molecular mechanisms of Pb release during Portland cement leaching. As Pb release is strongly related to its speciation (i.e. atomic environment and the nature of bearing phases), the first objective of the present study was to investigate the evolution of Pb retention sites together with the evolution of the cement mineralogy during leaching. Complementary and efficient investigation tools were used, namely X-ray diffraction, micro-X-ray fluorescence and X-ray absorption fine structures. The second objective was to reproduce our results with a reactive transport code (CHESS/HYTEC) in order to test the proposed speciation model of Pb. Combined results indicate that in both the unaltered core and the altered layer of the leached cement, Pb(II) would be retained through C-S-H 'nano-structure', probably linked to a Q(1) or Q(2P) silicate tetrahedra. Moreover in the altered layer, the presence of Fe atoms in the atomic environment of Pb is highly probable. Unfortunately little is known about Fe phases in cement, which makes the interpretation difficult. Can Fe-substituted hydrogranet (C(3)AH(6)) be responsible for Pb retention? Modelling results were consistent with Pb retention through C-S-H in layers and also in an additional, possibly Fe-containing, Pb-retention phase in the altered layer. (authors)

Fission product release from TRIGA-LEU reactor fuels

International Nuclear Information System (INIS)

Baldwin, N.L.; Foushee, F.C.; Greenwood, J.S.

1980-01-01

Due to present international concerns over nuclear proliferation, TRIGA reactor fuels will utilize only low-enriched uranium (LEU) (enrichment <20%). This requires increased total uranium loading per unit volume of fuel in order to maintain the appropriate fissile loading. Tests were conducted to determine the fractional release of gaseous and metallic fission products from typical uranium-zirconium hydride TRIGA fuels containing up to 45 wt-% uranium. These tests, performed in late 1977 and early 1978, were similar to those conducted earlier on TRIGA fuels with 8.5 wt-% U. Fission gas release measurements were made on prototypic specimens from room temperature to 1100 deg. C in the TRIGA King Furnace Facility. The fuel specimens were irradiated in the TRIGA reactor at a low power level. The fractional releases of the gaseous nuclides of krypton and xenon were measured under steady-state operating conditions. Clean helium was used to sweep the fission gases released during irradiation from the furnace into a standard gas collection trap for gamma counting. The results of these tests on TRIGA-LEU fuel agree well with data from the similar, earlier tests on TRIGA fuel. The correlation used to calculate the release of fission products from 8.5 wt-% U TRIGA fuel applies equally well for U contents up to 45 wt-%. (author)

COMMERCIAL SNF ACCIDENT RELEASE FRACTIONS

Energy Technology Data Exchange (ETDEWEB)

S.O. Bader

1999-10-18

The purpose of this design analysis is to specify and document the total and respirable fractions for radioactive materials that are released from an accident event at the Monitored Geologic Repository (MGR) involving commercial spent nuclear fuel (CSNF) in a dry environment. The total and respirable release fractions will be used to support the preclosure licensing basis for the MGR. The total release fraction is defined as the fraction of total CSNF assembly inventory, typically expressed as an activity inventory (e.g., curies), of a given radionuclide that is released to the environment from a waste form. The radionuclides are released from the inside of breached fuel rods (or pins) and from the detachment of radioactive material (crud) from the outside surfaces of fuel rods and other components of fuel assemblies. The total release fraction accounts for several mechanisms that tend to retain, retard, or diminish the amount of radionuclides that are available for transport to dose receptors or otherwise can be shown to reduce exposure of receptors to radiological releases. The total release fraction includes a fraction of airborne material that is respirable and could result in inhalation doses. This subset of the total release fraction is referred to as the respirable release fraction. Potential accidents may involve waste forms that are characterized as either bare (unconfined) fuel assemblies or confined fuel assemblies. The confined CSNF assemblies at the MGR are contained in shipping casks, canisters, or disposal containers (waste packages). In contrast to the bare fuel assemblies, the container that confines the fuel assemblies has the potential of providing an additional barrier for diminishing the total release fraction should the fuel rod cladding breach during an accident. However, this analysis will not take credit for this additional bamer and will establish only the total release fractions for bare unconfined CSNF assemblies, which may however be

COMMERCIAL SNF ACCIDENT RELEASE FRACTIONS

International Nuclear Information System (INIS)

S.O. Bader

1999-01-01

The purpose of this design analysis is to specify and document the total and respirable fractions for radioactive materials that are released from an accident event at the Monitored Geologic Repository (MGR) involving commercial spent nuclear fuel (CSNF) in a dry environment. The total and respirable release fractions will be used to support the preclosure licensing basis for the MGR. The total release fraction is defined as the fraction of total CSNF assembly inventory, typically expressed as an activity inventory (e.g., curies), of a given radionuclide that is released to the environment from a waste form. The radionuclides are released from the inside of breached fuel rods (or pins) and from the detachment of radioactive material (crud) from the outside surfaces of fuel rods and other components of fuel assemblies. The total release fraction accounts for several mechanisms that tend to retain, retard, or diminish the amount of radionuclides that are available for transport to dose receptors or otherwise can be shown to reduce exposure of receptors to radiological releases. The total release fraction includes a fraction of airborne material that is respirable and could result in inhalation doses. This subset of the total release fraction is referred to as the respirable release fraction. Potential accidents may involve waste forms that are characterized as either bare (unconfined) fuel assemblies or confined fuel assemblies. The confined CSNF assemblies at the MGR are contained in shipping casks, canisters, or disposal containers (waste packages). In contrast to the bare fuel assemblies, the container that confines the fuel assemblies has the potential of providing an additional barrier for diminishing the total release fraction should the fuel rod cladding breach during an accident. However, this analysis will not take credit for this additional bamer and will establish only the total release fractions for bare unconfined CSNF assemblies, which may however be

Effect of Multimodal Pore Channels on Cargo Release from Mesoporous Silica Nanoparticles

Directory of Open Access Journals (Sweden)

Sushilkumar A. Jadhav

2016-01-01

Full Text Available Mesoporous silica nanoparticles (MSNs with multimodal pore channels were fully characterized by TEM, nitrogen adsorption-desorption, and DLS analyses. MSNs with average diameter of 200 nm with dual pore channel zones with pore diameters of 1.3–2.6 and 4 nm were tested for their use in drug delivery application. Important role of the multimodal pore systems present on MSNs on the quantitative release of model drug ibuprofen was investigated. The results obtained revealed that the release profile for ibuprofen clearly shows distinct zones which can be attributed to the respective porous channel zones present on the particles. The fluctuations in the concentration of ibuprofen during the prolonged release from MSNs were caused by the multimodal pore channel systems.

Cobalt release from inexpensive jewellery

DEFF Research Database (Denmark)

Thyssen, Jacob Pontoppidan; Jellesen, Morten Stendahl; Menné, Torkil

2010-01-01

. Conclusions: This study showed that only a minority of inexpensive jewellery purchased in Denmark released cobalt when analysed with the cobalt spot test. As fashion trends fluctuate and we found cobalt release from dark appearing jewellery, cobalt release from consumer items should be monitored in the future......Objectives: The aim was to study 354 consumer items using the cobalt spot test. Cobalt release was assessed to obtain a risk estimate of cobalt allergy and dermatitis in consumers who would wear the jewellery. Methods: The cobalt spot test was used to assess cobalt release from all items...

MUDMAP: Simulation model for releases from offshore platforms

International Nuclear Information System (INIS)

Anon.

1994-01-01

The present article deals with a Norwegian developed simulation model dubbed MUDMAP. MUDMAP is a numerical model that simulates releases of drill muds and cuttings, produced water and other substances from offshore platforms. The model is envisioned as an advanced tool to assist in the rapid design and placement of intakes and release pipes on platforms, as well as in evaluating potential long-term impacts in the water and on the sea floor. MUDMAP allows rapid visual/graphical analysis of potential alternative solutions under various realistic environmental conditions, and for planning and executing platform monitoring projects. 4 figs

Release of volatile mercury from vascular plants

Science.gov (United States)

Siegel, S. M.; Puerner, N. J.; Speitel, T. W.

1974-01-01

Volatile, organic solvent soluble mercury has been found in leaves and seeds of several angiosperms. Leaves of garlic vine, avocado, and haole-koa release mercury in volatile form rapidly at room temperature. In garlic vine, the most active release is temperature dependent, but does not parallel the vapor-pressure temperature relationship for mercury. Mercury can be trapped in nitric-perchloric acid digestion fluid, or n-hexane, but is lost from the hexane unless the acid mixture is present. Seeds of haole-koa also contain extractable mercury but volatility declines in the series n-hexane (90%), methanol (50%), water (10%). This suggests that reduced volatility may accompany solvolysis in the more polar media.

Gaia Data Release 1. Testing parallaxes with local Cepheids and RR Lyrae stars

NARCIS (Netherlands)

Gaia Collaboration, [Unknown; Clementini, G.; Eyer, L.; Ripepi, V.; Marconi, M.; Muraveva, T.; Garofalo, A.; Sarro, L. M.; Palmer, M.; Luri, X.; Molinaro, R.; Rimoldini, L.; Szabados, L.; Musella, I.; Anderson, R. I.; Prusti, T.; de Bruijne, J. H. J.; Brown, A. G. A.; Vallenari, A.; Babusiaux, C.; Bailer-Jones, C. A. L.; Bastian, U.; Biermann, M.; Evans, D. W.; Jansen, F.; Jordi, C.; Klioner, S. A.; Lammers, U.; Lindegren, L.; Mignard, F.; Panem, C.; Pourbaix, D.; Randich, S.; Sartoretti, P.; Siddiqui, H. I.; Soubiran, C.; Valette, V.; van Leeuwen, F.; Walton, N. A.; Aerts, C.; Arenou, F.; Cropper, M.; Drimmel, R.; Høg, E.; Katz, D.; Lattanzi, M. G.; O'Mullane, W.; Grebel, E. K.; Holland, A. D.; Huc, C.; Passot, X.; Perryman, M.; Bramante, L.; Cacciari, C.; Castañeda, J.; Chaoul, L.; Cheek, N.; De Angeli, F.; Fabricius, C.; Guerra, R.; Hernández, J.; Jean-Antoine-Piccolo, A.; Masana, E.; Messineo, R.; Mowlavi, N.; Nienartowicz, K.; Ordóñez-Blanco, D.; Panuzzo, P.; Portell, J.; Richards, P. J.; Riello, M.; Seabroke, G. M.; Tanga, P.; Thévenin, F.; Torra, J.; Els, S. G.; Gracia-Abril, G.; Comoretto, G.; Garcia-Reinaldos, M.; Lock, T.; Mercier, E.; Altmann, M.; Andrae, R.; Astraatmadja, T. L.; Bellas-Velidis, I.; Benson, K.; Berthier, J.; Blomme, R.; Busso, G.; Carry, B.; Cellino, A.; Cowell, S.; Creevey, O.; Cuypers, J.; Davidson, M.; De Ridder, J.; de Torres, A.; Delchambre, L.; Dell'Oro, A.; Ducourant, C.; Frémat, Y.; García-Torres, M.; Gosset, E.; Halbwachs, J.-L.; Hambly, N. C.; Harrison, D. L.; Hauser, M.; Hestroffer, D.; Hodgkin, S. T.; Huckle, H. E.; Hutton, A.; Jasniewicz, G.; Jordan, S.; Kontizas, M.; Korn, A. J.; Lanzafame, A. C.; Manteiga, M.; Moitinho, A.; Muinonen, K.; Osinde, J.; Pancino, E.; Pauwels, T.; Petit, J.-M.; Recio-Blanco, A.; Robin, A. C.; Siopis, C.; Smith, M.; Smith, K. W.; Sozzetti, A.; Thuillot, W.; van Reeven, W.; Viala, Y.; Abbas, U.; Abreu Aramburu, A.; Accart, S.; Aguado, J. J.; Allan, P. M.; Allasia, W.; Altavilla, G.; Álvarez, M. A.; Alves, J.; Andrei, A. H.; Anglada Varela, E.; Antiche, E.; Antoja, T.; Antón, S.; Arcay, B.; Bach, N.; Baker, S. G.; Balaguer-Núñez, L.; Barache, C.; Barata, C.; Barbier, A.; Barblan, F.; Barrado y Navascués, D.; Barros, M.; Barstow, M. A.; Becciani, U.; Bellazzini, M.; Bello García, A.; Belokurov, V.; Bendjoya, P.; Berihuete, A.; Bianchi, L.; Bienaymé, O.; Billebaud, F.; Blagorodnova, N.; Blanco-Cuaresma, S.; Boch, T.; Bombrun, A.; Borrachero, R.; Bouquillon, S.; Bourda, G.; Bragaglia, A.; Breddels, M. A.; Brouillet, N.; Brüsemeister, T.; Bucciarelli, B.; Burgess, P.; Burgon, R.; Burlacu, A.; Busonero, D.; Buzzi, R.; Caffau, E.; Cambras, J.; Campbell, H.; Cancelliere, R.; Cantat-Gaudin, T.; Carlucci, T.; Carrasco, J. M.; Castellani, M.; Charlot, P.; Charnas, J.; Chiavassa, A.; Clotet, M.; Cocozza, G.; Collins, R. S.; Costigan, G.; Crifo, F.; Cross, N. J. G.; Crosta, M.; Crowley, C.; Dafonte, C.; Damerdji, Y.; Dapergolas, A.; David, P.; David, M.; De Cat, P.; de Felice, F.; de Laverny, P.; De Luise, F.; De March, R.; de Souza, R.; Debosscher, J.; del Pozo, E.; Delbo, M.; Delgado, A.; Delgado, H. E.; Di Matteo, P.; Diakite, S.; Distefano, E.; Dolding, C.; Dos Anjos, S.; Drazinos, P.; Durán, J.; Dzigan, Y.; Edvardsson, B.; Enke, H.; Evans, N. W.; Eynard Bontemps, G.; Fabre, C.; Fabrizio, M.; Falcão, A. J.; Farràs Casas, M.; Federici, L.; Fedorets, G.; Fernández-Hernández, J.; Fernique, P.; Fienga, A.; Figueras, F.; Filippi, F.; Findeisen, K.; Fonti, A.; Fouesneau, M.; Fraile, E.; Fraser, M.; Fuchs, J.; Gai, M.; Galleti, S.; Galluccio, L.; Garabato, D.; García-Sedano, F.; Garralda, N.; Gavras, P.; Gerssen, J.; Geyer, R.; Gilmore, G.; Girona, S.; Giuffrida, G.; Gomes, M.; González-Marcos, A.; González-Núñez, J.; González-Vidal, J. J.; Granvik, M.; Guerrier, A.; Guillout, P.; Guiraud, J.; Gúrpide, A.; Gutiérrez-Sánchez, R.; Guy, L. P.; Haigron, R.; Hatzidimitriou, D.; Haywood, M.; Heiter, U.; Helmi, A.; Hobbs, D.; Hofmann, W.; Holl, B.; Holland, G.; Hunt, J. A. S.; Hypki, A.; Icardi, V.; Irwin, M.; Jevardat de Fombelle, G.; Jofré, P.; Jonker, P. G.; Jorissen, A.; Julbe, F.; Karampelas, A.; Kochoska, A.; Kohley, R.; Kolenberg, K.; Kontizas, E.; Koposov, S. E.; Kordopatis, G.; Koubsky, P.; Krone-Martins, A.; Kudryashova, M.; Bachchan, R. K.; Lacoste-Seris, F.; Lanza, A. F.; Lavigne, J.-B.; Le Poncin-Lafitte, C.; Lebreton, Y.; Lebzelter, T.; Leccia, S.; Leclerc, N.; Lecoeur-Taibi, I.; Lemaitre, V.; Lenhardt, H.; Leroux, F.; Liao, S.; Licata, E.; Lindstrøm, H. E. P.; Lister, T. A.; Livanou, E.; Lobel, A.; Löffler, W.; López, M.; Lorenz, D.; MacDonald, I.; Magalhães Fernandes, T.; Managau, S.; Mann, R. G.; Mantelet, G.; Marchal, O.; Marchant, J. M.; Marinoni, S.; Marrese, P. M.; Marschalkó, G.; Marshall, D. J.; Martín-Fleitas, J. M.; Martino, M.; Mary, N.; Matijevič, G.; McMillan, P. J.; Messina, S.; Michalik, D.; Millar, N. R.; Miranda, B. M. H.; Molina, D.; Molinaro, M.; Molnár, L.; Moniez, M.; Montegriffo, P.; Mor, R.; Mora, A.; Morbidelli, R.; Morel, T.; Morgenthaler, S.; Morris, D.; Mulone, A. F.; Narbonne, J.; Nelemans, G.; Nicastro, L.; Noval, L.; Ordénovic, C.; Ordieres-Meré, J.; Osborne, P.; Pagani, C.; Pagano, I.; Pailler, F.; Palacin, H.; Palaversa, L.; Parsons, P.; Pecoraro, M.; Pedrosa, R.; Pentikäinen, H.; Pichon, B.; Piersimoni, A. M.; Pineau, F.-X.; Plachy, E.; Plum, G.; Poujoulet, E.; Prša, A.; Pulone, L.; Ragaini, S.; Rago, S.; Rambaux, N.; Ramos-Lerate, M.; Ranalli, P.; Rauw, G.; Read, A.; Regibo, S.; Reylé, C.; Ribeiro, R. A.; Riva, A.; Rixon, G.; Roelens, M.; Romero-Gómez, M.; Rowell, N.; Royer, F.; Ruiz-Dern, L.; Sadowski, G.; Sagristà Sellés, T.; Sahlmann, J.; Salgado, J.; Salguero, E.; Sarasso, M.; Savietto, H.; Schultheis, M.; Sciacca, E.; Segol, M.; Segovia, J. C.; Segransan, D.; Shih, I.-C.; Smareglia, R.; Smart, R. L.; Solano, E.; Solitro, F.; Sordo, R.; Soria Nieto, S.; Souchay, J.; Spagna, A.; Spoto, F.; Stampa, U.; Steele, I. A.; Steidelmüller, H.; Stephenson, C. A.; Stoev, H.; Suess, F. F.; Süveges, M.; Surdej, J.; Szegedi-Elek, E.; Tapiador, D.; Taris, F.; Tauran, G.; Taylor, M. B.; Teixeira, R.; Terrett, D.; Tingley, B.; Trager, S. C.; Turon, C.; Ulla, A.; Utrilla, E.; Valentini, G.; van Elteren, A.; Van Hemelryck, E.; van Leeuwen, M.; Varadi, M.; Vecchiato, A.; Veljanoski, J.; Via, T.; Vicente, D.; Vogt, S.; Voss, H.; Votruba, V.; Voutsinas, S.; Walmsley, G.; Weiler, M.; Weingrill, K.; Wevers, T.; Wyrzykowski, Ł.; Yoldas, A.; Žerjal, M.; Zucker, S.; Zurbach, C.; Zwitter, T.; Alecu, A.; Allen, M.; Allende Prieto, C.; Amorim, A.; Anglada-Escudé, G.; Arsenijevic, V.; Azaz, S.; Balm, P.; Beck, M.; Bernstein, H.-H.; Bigot, L.; Bijaoui, A.; Blasco, C.; Bonfigli, M.; Bono, G.; Boudreault, S.; Bressan, A.; Brown, S.; Brunet, P.-M.; Bunclark†, P.; Buonanno, R.; Butkevich, A. G.; Carret, C.; Carrion, C.; Chemin, L.; Chéreau, F.; Corcione, L.; Darmigny, E.; de Boer, K. S.; de Teodoro, P.; de Zeeuw, P. T.; Delle Luche, C.; Domingues, C. D.; Dubath, P.; Fodor, F.; Frézouls, B.; Fries, A.; Fustes, D.; Fyfe, D.; Gallardo, E.; Gallegos, J.; Gardiol, D.; Gebran, M.; Gomboc, A.; Gómez, A.; Grux, E.; Gueguen, A.; Heyrovsky, A.; Hoar, J.; Iannicola, G.; Isasi Parache, Y.; Janotto, A.-M.; Joliet, E.; Jonckheere, A.; Keil, R.; Kim, D.-W.; Klagyivik, P.; Klar, J.; Knude, J.; Kochukhov, O.; Kolka, I.; Kos, J.; Kutka, A.; Lainey, V.; LeBouquin, D.; Liu, C.; Loreggia, D.; Makarov, V. V.; Marseille, M. G.; Martayan, C.; Martinez-Rubi, O.; Massart, B.; Meynadier, F.; Mignot, S.; Munari, U.; Nguyen, A.-T.; Nordlander, T.; O'Flaherty, K. S.; Ocvirk, P.; Olias Sanz, A.; Ortiz, P.; Osorio, J.; Oszkiewicz, D.; Ouzounis, A.; Park, P.; Pasquato, E.; Peltzer, C.; Peralta, J.; Péturaud, F.; Pieniluoma, T.; Pigozzi, E.; Poels†, J.; Prat, G.; Prod'homme, T.; Raison, F.; Rebordao, J. M.; Risquez, D.; Rocca-Volmerange, B.; Rosen, S.; Ruiz-Fuertes, M. I.; Russo, F.; Serraller Vizcaino, I.; Short, A.; Siebert, A.; Silva, H.; Sinachopoulos, D.; Slezak, E.; Soffel, M.; Sosnowska, D.; Straižys, V.; ter Linden, M.; Terrell, D.; Theil, S.; Tiede, C.; Troisi, L.; Tsalmantza, P.; Tur, D.; Vaccari, M.; Vachier, F.; Valles, P.; Van Hamme, W.; Veltz, L.; Virtanen, J.; Wallut, J.-M.; Wichmann, R.; Wilkinson, M. I.; Ziaeepour, H.; Zschocke, S.

2017-01-01

Context. Parallaxes for 331 classical Cepheids, 31 Type II Cepheids, and 364 RR Lyrae stars in common between Gaia and the Hipparcos and Tycho-2 catalogues are published in Gaia Data Release 1 (DR1) as part of the Tycho-Gaia Astrometric Solution (TGAS). Aims: In order to test these first parallax

Fission product release from nuclear fuel I. Physical modelling in the ASTEC code

International Nuclear Information System (INIS)

Brillant, G.; Marchetto, C.; Plumecocq, W.

2013-01-01

Highlights: • Physical modeling of FP and SM release in ASTEC is presented. • The release is described as solid state diffusion within fuel for high volatile FP. • The release is described as FP vaporisation for semi volatile FP. • The release is described as fuel vaporisation for low volatile FP. • ASTEC validation is presented in the second paper. - Abstract: This article is the first of a series of two articles dedicated to the mechanisms of fission product release from a degraded core as they are modelled in the ASTEC code. The ASTEC code aims at simulating severe accidents in nuclear reactors from the initiating event up to the radiological consequences on the environment. This code is used for several applications such as nuclear plant safety evaluation including probabilistic studies and emergency preparedness. To cope with the requirements of robustness and low calculation time, the code is based on a semi-empirical approach and only the main limiting phenomena that govern the release from intact rods and from debris beds are considered. For solid fuel, fission products are classified into three groups, depending on their degree of volatility. The kinetics of volatile fission products release depend on the rate-limiting process of solid-state diffusion through fuel grains. For semi-volatile fission products, the release from the open fuel porosities is assumed to be governed by vaporisation and mass transfer processes. The key phenomenon for the release of low volatile fission products is supposed to be fuel volatilisation. A similar approach is used for the release of fission products from a rubble bed. An in-depth validation of the code including both analytical and integral experiments is the subject of the second article

Extracellular ATP in the Exocrine Pancreas – ATP Release, Signalling and Metabolism

DEFF Research Database (Denmark)

Kowal, Justyna Magdalena

release. So far, the contribution of duct cells in purinergic signalling has never been studied. This work presents that both acinar and duct cells are sources of extracellular ATP in the exocrine pancreas. Here we show that duct cells release ATP in response to several physiological......ATP plays an important role as an autocrine/paracrine signalling molecule, being released from a number of tissues, in response to physiological and pathophysiological stimuli. Released ATP induces Ca2+ - and/or cAMP - dependent cellular responses via activation of ubiquitously expressed P2X and P2......, particularly during Ca2+ stress conditions. In conclusion, these studies demonstrate a complex regulation of purinergic signalling in exocrine pancreas. A crucial role for duct cells in mediating extracellular nucleotides homeostasis, involving ATP release, subsequent hydrolysis and conversion via...

Radionuclide release from PWR spent fuel specimens with induced cladding defects

International Nuclear Information System (INIS)

Wilson, C.N.; Oversby, V.M.

1984-03-01

Radionuclide releases from pressurized water reactor (PWR) spent fuel rod specimens containing various artificially induced cladding defects were compared by leach testing. The study was conducted in support of the Nevada Nuclear Waste Storage Investigations (NNWSI) Waste Package Task to evaluate the effectiveness of failed cladding as a barrier to radionuclide release. Test description and results are presented. 6 references, 4 figures

Laser-activated nano-biomaterials for tissue repair and controlled drug release

International Nuclear Information System (INIS)

Matteini, P; Ratto, F; Rossi, F; Pini, R

2014-01-01

We present recent achievements of minimally invasive welding of biological tissue and controlled drug release based on laser-activated nano-biomaterials. In particular, we consider new advancements in the biomedical application of near-IR absorbing gold nano-chromophores as an original solution for the photothermal repair of surgical incisions and as nanotriggers of controlled drug release from hybrid biopolymer scaffolds. (laser biophotonics)

Consequences of tritium release to water pathways from postulated accidents in a DOE production reactor

International Nuclear Information System (INIS)

O'Kula, K.R.; Olson, R.L.; Hamby, D.M.

1991-01-01

A full-scale PRA of a DOE production reactor has been completed that considers full release of tritium as part of the severe accident source term. Two classes of postulated reactor accidents, a loss-of-moderator pumping accident and a loss-of-coolant accident, are used to bound the expected dose consequence from liquid pathway release. Population doses from the radiological release associated with the two accidents are compared for aqueous discharge and atmospheric release modes. The expectation values of the distribution of possible values for the societal effective dose equivalent to the general public, given a tritium release to the atmosphere, is 2.8 person-Sv/PBq (9.9 x 10 -3 person-rem/Ci). The general public drinking water dose to downstream water consumers is 6.5 x 10 -2 person-Sv/Pbq (2.4 x 10 -4 person-rem/Ci) for aqueous releases to the surface streams eventually reaching the Savannah River. Negligible doses are calculated for freshwater fish and saltwater invertebrate consumption, irrigation, and recreational use of the river, given that an aqueous release is assumed to occur. Relative to the balance of fission products released in a hypothetical severe accident, the tritium-related dose is small. This study suggests that application of regional models (1610 km radius) will indicate larger dose consequences from short-term tritium release to the atmosphere than from comparable tritium source terms to water pathways. However, the water pathways assessment is clearly site-specific, and the overall aqueous dose will be dependent on downstream receptor populations and uses of the river

Relative Release-to-Birth Indicators for Investigating TRISO Fuel Fission Gas Release Models

International Nuclear Information System (INIS)

Harp, Jason M.; Hawari, Ayman I.

2008-01-01

TRISO microsphere fuel is the fundamental fuel unit for Very High Temperature Reactors (VHTR). A single TRISO particle consists of an inner kernel of uranium dioxide or uranium oxycarbide surrounded by layers of pyrolytic carbon and silicon carbide. If the silicon carbide layer fails, fission products, especially the noble fission gases Kr and Xe, will begin to escape the failed particle. The release of fission gas is usually quantified by measuring the ratio of the released activity (R) to the original birth activity (B), which is designated as the R/B ratio. In this work, relative Release-to-Birth indicators (I) are proposed as a technique for interpreting the results of TRISO irradiation experiments. By implementing a relative metric, it is possible to reduce the sensitivity of the indicators to instrumental uncertainties and variations in experimental conditions. As an example, relative R/B indicators are applied to the interpretation of representative data from the Advanced Gas Reactor-1 TRISO fuel experiment that is currently taking place at the Advanced Test Reactor of Idaho National Laboratory. It is shown that the comparison of measured to predicted relative R/B indicators (I) gives insight into the physics of release and helps validate release models. Different trends displayed by the indicators are related to the mechanisms of fission gas release such as diffusion and recoil. The current analysis shows evidence for separate diffusion coefficients for Kr and Xe and supports the need to account for recoil release. (authors)

Dose apportionment using statistical modeling of the effluent release

International Nuclear Information System (INIS)

Datta, D.

2011-01-01

Nuclear power plants are always operated under the guidelines stipulated by the regulatory body. These guidelines basically contain the technical specifications of the specific power plant and provide the knowledge of the discharge limit of the radioactive effluent into the environment through atmospheric and aquatic route. However, operational constraints sometimes may violate the technical specification due to which there may be a failure to satisfy the stipulated dose apportioned to that plant. In a site having multi facilities sum total of the dose apportioned to all the facilities should be constrained to 1 mSv/year to the members of the public. Dose apportionment scheme basically stipulates the limit of the gaseous and liquid effluent released into the environment. Existing methodology of dose apportionment is subjective in nature that may result the discharge limit of the effluent in atmospheric and aquatic route in an adhoc manner. Appropriate scientific basis for dose apportionment is always preferable rather than judicial basis from the point of harmonization of establishing the dose apportionment. This paper presents an attempt of establishing the discharge limit of the gaseous and liquid effluent first on the basis of the existing value of the release of the same. Existing release data for a few years (for example 10 years) for any nuclear power station have taken into consideration. Bootstrap, a resampling technique, has been adopted on this data sets to generate the population which subsequently provide the corresponding population distribution of the effluent release. Cumulative distribution of the population distribution obtained is constructed and using this cumulative distribution, 95th percentile (upper bound) of the discharge limit of the radioactive effluents is computed. Dose apportioned for a facility is evaluated using this estimated upper bound of the release limit. Paper describes the detail of the bootstrap method in evaluating the

Drug release from non-aqueous suspensions. II. The release of methylxanthines from paraffin suspensions

NARCIS (Netherlands)

Blaey, C.J. de; Fokkens, J.G.

1984-01-01

The release of 3 methylxanthines, i.e. caffeine, theobromine and theophylline, from suspensions in liquid paraffin to an aqueous phase was determined in an in vitro apparatus. The release rates were determined as a function of the pH of the aqueous phase. It was proved that the release process was

Risk from a pressurized toxic gas system: Part 2, Dispersal consequences

International Nuclear Information System (INIS)

Brereton, S.J.; Altenbach, T.J.; Lane, S.G.; Martin, D.W.

1995-02-01

During the preparation of a Safety Analysis Report at the Lawrence Livermore National Laboratory. we studied the release of chlorine from a compressed gas experimental apparatus. This paper presents the second pan in a series of two papers on this topic. The first paper focuses on the frequency of an unmitigated release from the system; paper focuses the consequences of the release. The release of chlorine from the experimental apparatus was modeled as an unmitigated blowdown through a 0.25 inch (0.006.4 m) outside diameter tube. The physical properties of chlorine were considered as were the dynamics of the fluid flow problem. The calculated release rate was used as input for the consequence assessment. Downwind concentrations as a function of time were evaluated and then compared to suggested guidelines. For comparison purposes, a typical water treatment plant was briefly studied. The lower hazard presented by the LLNL operation becomes evident when its release is compared to the release of material from a water treatment plant, a hazard which is generally accepted by the public

Regulatory analysis on criteria for the release of patients administered radioactive material

International Nuclear Information System (INIS)

Schneider, S.; McGuire, S.A.

1994-05-01

The Nuclear Regulatory Commission (NRC) has received two petitions to amend its regulations in 10 CFR Parts 20 and 35 as they apply to doses received by members of the public exposed to patients released from a hospital after they have been administered radioactive material. While the two petitions are not identical they both request that the NRC establish a dose limit of 5 millisieverts (0.5 rem) per year for individuals exposed to patients who have been administered radioactive materials. This Regulatory Analysis evaluates three alternatives. Alternative 1 is for the NRC to amend its patient release criteria in 10 CFR 35.75 to use the more stringent dose limit of 1 millisievert per year in 10 CFR 20.1301(a) for its patient release criteria. Alternative 2 is for the NRC to continue using the existing patient release criteria in 10 CFR 35.75 of 1,110 megabecquerels of activity or a dose rate at one meter from the patient of 0.05 millisievert per hour. Alternative 3 is for the NRC to amend the patient release criteria in 10 CFR 35.75 to specify a dose limit of 5 millisieverts for patient release. The evaluation indicates that Alternative 1 would cause a prohibitively large increase in the national health care cost from retaining patients in a hospital longer and would cause significant personal and psychological costs to patients and their families. The choice of Alternatives 2 or 3 would affect only thyroid cancer patients treated with iodine-131. For those patients, Alternative 3 would result in less hospitalization than Alternative 2. Alternative 3 has a potential decrease in national health care cost of $30,000,000 per year but would increase the potential collective dose from released therapy patients by about 2,700 person-rem per year, mainly to family members

Regulatory analysis on criteria for the release of patients administered radioactive material

Energy Technology Data Exchange (ETDEWEB)

Schneider, S.; McGuire, S.A. [Nuclear Regulatory Commission, Washington, DC (United States). Div. of Regulatory Applications; Behling, U.H.; Behling, K.; Goldin, D. [Cohen (S.) and Associates, Inc., McLean, VA (United States)

1994-05-01

The Nuclear Regulatory Commission (NRC) has received two petitions to amend its regulations in 10 CFR Parts 20 and 35 as they apply to doses received by members of the public exposed to patients released from a hospital after they have been administered radioactive material. While the two petitions are not identical they both request that the NRC establish a dose limit of 5 millisieverts (0.5 rem) per year for individuals exposed to patients who have been administered radioactive materials. This Regulatory Analysis evaluates three alternatives. Alternative 1 is for the NRC to amend its patient release criteria in 10 CFR 35.75 to use the more stringent dose limit of 1 millisievert per year in 10 CFR 20.1301(a) for its patient release criteria. Alternative 2 is for the NRC to continue using the existing patient release criteria in 10 CFR 35.75 of 1,110 megabecquerels of activity or a dose rate at one meter from the patient of 0.05 millisievert per hour. Alternative 3 is for the NRC to amend the patient release criteria in 10 CFR 35.75 to specify a dose limit of 5 millisieverts for patient release. The evaluation indicates that Alternative 1 would cause a prohibitively large increase in the national health care cost from retaining patients in a hospital longer and would cause significant personal and psychological costs to patients and their families. The choice of Alternatives 2 or 3 would affect only thyroid cancer patients treated with iodine-131. For those patients, Alternative 3 would result in less hospitalization than Alternative 2. Alternative 3 has a potential decrease in national health care cost of $30,000,000 per year but would increase the potential collective dose from released therapy patients by about 2,700 person-rem per year, mainly to family members.

International comparison on radioactive releases of PWR between 1975 and 1988

International Nuclear Information System (INIS)

Benedittini, M.; Tabare, M.

1990-02-01

This report presents the main results of a comparison on radioactive releases from 135 PWRs in the following countries: Belgium, Federal Republic of Germany, Finland, France, Japan, Sweden, Switzerland and the United States. For liquid releases, distinctions have been undertaken between tritium and no tritium activities and for gaseous releases between noble gases and halogens-aerosols. Data has been collected from literature published or by contacting utilities administrative staff or authorities in order to constitute a data base. As regards this comparison however, reactors, the commercial operation of which started prior to July 1974, have been excluded [fr

Nuclear computerized library for assessing reactor reliability (NUCLARR): Data manual: Part 1, Summary description

International Nuclear Information System (INIS)

Gertman, D.I.; Gilbert, B.G.; Gilmore, W.E.; Galyean, W.J.

1988-06-01

This volume of a five-volume series summarizes those data currently resident in the first release of the Nuclear Computerized Library for Assessing Reactor Reliability (NUCLARR) data base. The raw human error probability (HEP) and hardware component failure data (HCFD) contained herein are accompanied by a glossary of terms and the HEP and hardware taxonomies used to structure the data. Instructions are presented on how the user may navigate through the NUCLARR data management system to find anchor values to assist in solving risk-related problems. Volume V: Data Manual will be updated on a periodic basis so that risk analysis without access to a computer may have access to the largest NUCLARR data. This document Part 1 of Volume 5 introduces aspects of the NUCLARR data base management system and prepares the reader for reviewing data in other Parts of Volume 5

Fluoride release and surface roughness of a new glass ionomer cement: glass carbomer

Directory of Open Access Journals (Sweden)

Célia Maria Condeixa de França LOPES

2018-02-01

Full Text Available Abstract Objective This study analyzed the fluoride release/recharge and surface roughness of glass carbomer compared to other encapsulated glass ionomer cements (GICs. Material and method The GICs tested were Glass Fill® (GC-GCP Dental, Riva Self Cure® (RS-SDI, Riva Light Cure® (RL-SDI, Equia Fil® (EF-GC Europe. The composite resin Luna® (LU-SDI was used as control. Five samples of each material were prepared and kept in a humidifier for 24 hours (37 °C, 100% relative humidity. Fluoride release was measured in two times: before (T1: days 1, 2, 7, 14 and after topical application of fluoride (T2: days 15, 16, 21 and 28. The surface roughness was also measured in both times (T1: days 1 and 14; T2: days 15 and 28. All samples were submitted to a single topical application of acidulated fluoride phosphate (Fluor Care - FGM. Two-way ANOVA with repeated measures and Tukey's post-test (p <0.05 were used in the statistical analysis. Result Equia Fil presented the highest fluoride release in both evaluation periods, with a higher release in T1 (p <0.05. The other materials tested, including glass carbomer presented similar release in both periods (T1 and T2. Regarding surface roughness, no significant differences were observed in the interaction between the material × time factors (T1 and T2 (p=0.966. Conclusion The GICs tested presented fluoride release and recharge ability and showed no surface roughness increase by topical application of fluoride.

Manufacture of plastic parts by radiation molding

International Nuclear Information System (INIS)

Leszyk, G.M.; Morrison, E.D.; Williams, R.F. Jr.

1977-01-01

Thin plastic parts which can have precise tolerances and can be of complex shape are prepared by casting a viscous radiation-curable composition onto a support, such as a moving web of polymeric material, in the shape of the desired part and then irradiating, for example with ultraviolet radiation or high energy electrons, to cause curing of the composition to a solid plastic. The radiation-curable composition is formulated with viscosity and flow characteristics it to be cast in the exact shape of the part desired yet retain this shape during curing while supported only by the surface on which it has been cast. Plastic parts made by this method can be formed entirely of the radiation-curable composition by casting onto a web having a release surface from which the part can be stripped subsequent to curing or can be formed partially from a web material and partially from the radiation-curable composition by casting onto a web to which the composition will bond and subsequently cutting the web into discrete portions which include the cured composition

Future trends in the assessment of hazards from fission product releases

Energy Technology Data Exchange (ETDEWEB)